Controlling fugitive emissions from mechanical seals

International Nuclear Information System (INIS)

Adams, W.V.

1992-01-01

This paper reports that enactment of the 1990 Federal Clean Air Amendments will sharply focus efforts in the process industries to reduce fugitive emissions. Moreover, state and local governments may be imposing stricter laws and regulations which will affect allowable fugitive emissions from U.S. refineries and process plants. Plants outside the U.S. have similar concerns. Clearly, mechanical seals for process pumps represent an enormous population and is one category of equipment destined for careful evaluation as a means to control fugitive emissions. Fugitive are unintentional emissions from valves, pumps, flanges, compressors, etc., as opposed to point-source emissions from stacks, vents and flares. Fugitive emissions do not occur as a part of normal plant operations, but result from the effects of: Malfunctions, Age, Lack of proper maintenance, Operator error, Improper equipment specification, Use of inferior technology, and externally caused damage

Impact of fugitive sources and meteorological parameters on vertical distribution of particulate matter over the industrial agglomeration.

Science.gov (United States)

Štrbová, Kristína; Raclavská, Helena; Bílek, Jiří

2017-12-01

The aim of the study was to characterize vertical distribution of particulate matter, in an area well known by highest air pollution levels in Europe. A balloon filled with helium with measuring instrumentation was used for vertical observation of air pollution over the fugitive sources in Moravian-Silesian metropolitan area during spring and summer. Synchronously, selected meteorological parameters were recorded together with particulate matter for exploration its relationship with particulate matter. Concentrations of particulate matter in the vertical profile were significantly higher in the spring than in the summer. Significant effect of fugitive sources was observed up to the altitude ∼255 m (∼45 m above ground) in both seasons. The presence of inversion layer was observed at the altitude ∼350 m (120-135 m above ground) at locations with major source traffic load. Both particulate matter concentrations and number of particles for the selected particle sizes decreased with increasing height. Strong correlation of particulate matter with meteorological parameters was not observed. The study represents the first attempt to assess the vertical profile over the fugitive emission sources - old environmental burdens in industrial region. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characteristics of PM10 Chemical Source Profiles for Geological Dust from the South-West Region of China

Directory of Open Access Journals (Sweden)

Yayong Liu

2016-11-01

Full Text Available Ninety-six particulate matter (PM10 chemical source profiles for geological sources in typical cities of southwest China were acquired from Source Profile Shared Service in China. Twenty-six elements (Na, Mg, Al, Si, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, As, Se, Sr, Cd, Sn, Sb, Ba, Be, Tl and Pb, nine ions (F−, Cl−, SO42−, NO3−, Na+, NH4+, K+, Mg2+ and Ca2+, and carbon-containing species (organic carbon and elemental carbon were determined to construct these profiles. Individual source profiles were averaged and compared to quantify similarities and differences in chemical abundances using the profile-compositing method. Overall, the major components of PM10 in geological sources were crustal minerals and undefined fraction. Different chemical species could be used as tracers for various types of geological dust in the region that resulted from different anthropogenic influence. For example, elemental carbon, V and Zn could be used as tracers for urban paved road dust; Al, Si, K+ and NH4+ for agricultural soil; Al and Si for natural soil; and SO42− for urban resuspended dust. The enrichment factor analysis showed that Cu, Se, Sr and Ba were highly enriched by human activities in geological dust samples from south-west China. Elemental ratios were taken to highlight the features of geological dust from south-west China by comparing with northern urban fugitive dust, loess and desert samples. Low Si/Al and Fe/Al ratios can be used as markers to trace geological sources from southwestern China. High Pb/Al and Zn/Al ratios observed in urban areas demonstrated that urban geological dust was influenced seriously by non-crustal sources.

Tracing Sources and Contamination Assessments of Heavy Metals in Road and Foliar Dusts in a Typical Mining City, China.

Directory of Open Access Journals (Sweden)

Jie Yang

Full Text Available Road and foliar dust samples from four land-use districts of Panzhihua City, a famous V-Ti magnetite production area of China, were collected to investigate the sources and distribution characteristics of 9 heavy metals (V, Pb, Cd, Cu, Zn, Ni, Cr, Fe, and Mn. The results suggest that foliar samples had smaller particle size and higher heavy metal contents than road dusts. The contamination assessments of heavy metals were as follows: Pb and V (significant enrichment > Zn, Ni, Cr, Fe, and Mn (moderate enrichment > Cd and Ni (minimal enrichment. Statistical analyses showed Pb, as the primary pollution element, originated from waste incineration and lead-fuel combustion. The sources of Zn, Ni, Cr, Fe, V, and Mn were fugitive dust and traffic activities. Potential origins of Cu were corrosion of alloys used in vehicle components, vehicle covers, or other metallic surfaces and materials. The sources of Cd were different from any other heavy metals. Traffic and industrial activities were the main anthropogenic origins of heavy metals in dusts of Panzhihua, and more attention should be paid to heavy metal pollution in agricultural area.

Fugitive Felons

Data.gov (United States)

Social Security Administration — The Fugitive Felon Reporting and Tracking System (FRATS) houses fugitive data submitted by reporters (RIDs) and warrant agencies (WAIDs). It also controls and tracks...

Using Epiphytic Lichens to Elucidate the Sources and Spatial Distribution of Inorganic Air Pollution in the Athabasca Oil Sands Region

Science.gov (United States)

Landis, M.; Graney, J. R.; Pancras, P.; Krupa, S.; Edgerton, E.; Puckett, K.; Percy, K.

2013-12-01

The Wood Buffalo Environmental Association (WBEA) conducted studies to document the geographic patterns of atmospheric deposition of sulfur (S) and nitrogen (N) in the Athabasca Oil Sands Region (AOSR) using epiphytic lichens as bioindicators of atmospheric pollution. Epiphytic lichen samples (Hypogymnia physodes) were collected from 44 locations in 2002, 359 locations in 2008, and 21 locations in 2011 within the AOSR. A subset of samples from 2002 (15) and 2008 (121); and all the samples from 2011 were microwave extracted and analyzed for a comprehensive suite of trace elements using DRC-ICPMS. In addition, source profiles were developed for samples from a variety of available process stacks, heavy duty diesel fleet vehicles, bulk materials representing the various stages of oil sands processing operations, and forest fires. The lichen monitoring and source profile information were integrated into a receptor modeling framework to elucidate the relative importance of natural and anthropogenic sources to the observed atmospheric deposition of S and N in the AOSR. U.S. EPA implemented statistical receptor models utilized included Positive Matrix Factorization (PMF), Unmix, and Chemical Mass Balance (CMB). The sources uniquely identified that significantly contributed to concentrations of elements in the lichen tissue include: fugitive dust from haul roads, tailing sand, and oil sand mining; oil sand processing; combustion processes; and a general urban regional source. The spatial patterns of CMB, PMF, and Unmix receptor model estimated source impacts on the Hypogymnia physodes tissue concentrations from the oil sand processing and fugitive dust sources had a significant association with the distance from the primary oil sands surface mining operations and related production facilities. The spatial extent of the fugitive dust impact was limited to an approximately 20 km radius around the major mining and oil production facilities, indicative of ground level coarse

Emission inventory for fugitive emissions from fuel in Denmark

DEFF Research Database (Denmark)

Plejdrup, Marlene Schmidt; Nielsen, Ole-Kenneth; Nielsen, Malene

This report presents the methodology and data used in the Danish inventory of fugitive emissions from fuels for the years until 2013. The inventory of fugitive emissions includes CO2, CH4, N2O, SO2, NOx, NMVOC, CO, particulate matter, Black carbon, heavy metals, dioxin and PAHs. In 2013 the total...... Danish emission of greenhouse gasses was 54 584 Gg CO2 equivalents. Fugitive emissions from fuels account for 387 Gg CO2 equivalents or approximately 1 %. The major part of the fugitive emissions are emitted as CO2 (61 %) mainly from flaring in upstream oil and gas production. The major source...... of fugitive CH4 emission is production of oil and gas in the North Sea, refining of oil and loading of oil onto ships both offshore and onshore. The fugitive emissions of NMVOC originate for the major part from oil and gas production, loading of ships, transmission and distribution of oil, and to a less...

Austrian emission inventory for dust

International Nuclear Information System (INIS)

Winiwarter, W.; Trenker, C.; Hoeflinger, W.

2001-09-01

For the first time, Austrian emissions of anthropogenic particulate matter emissions to the atmosphere have been estimated. Results have been reported as total suspended particles (TSP) as well as for the fractions of particles smaller than 10 μm or 2.5 μm aerodynamic diameter (PM 10 , PM 2.5 ), respectively. Base years for the inventory were 1990, 1995 and 1999. Excluded from this assessment is wind blown dust, which has been considered a natural source here. National statistics have been applied, specifically those also used previously in the Austrian air pollution inventory (OLI). Emission factors have been taken from literature compilations, only for exceptional cases specific Austrian assessments were performed or original literature on emission measurements was consulted. Resuspension of dust by road traffic emerged as the most important source. For the size fraction of PM 10 this source contributed about half of the emissions, when applying the calculation scheme by the U.S. EPA. While this scheme is widely used and well documented, its validity is currently subject of intense scientific debate. As these results do not seem to coincide with ambient air measurements, resuspension of road dust is considered separately and not now included in the national total. The sum of all other sources increases from 75,000 t of TSP in 1990 and 1995 to 77,000 t in 1999, while both PM 10 and PM 2.5 exhibit decreasing tendency (at 45,000 t and 26,000 t in 1999, respectively). The increase in TSP derives from increasing traffic and friction related emissions (tire wear, break wear), decrease of the finer particulate matter is due to reductions in firewood consumption for domestic heating. Most important source sectors are fugitive emissions from material transfer in industry as well as the building industry and the tilling of agricultural land. Common to these sources is the high uncertainty of available data. Wood combustion is the most important of the non-fugitive

[Influence of traffic restriction on road and construction fugitive dust].

Science.gov (United States)

Tian, Gang; Li, Gang; Qin, Jian-Ping; Fan, Shou-Bin; Huang, Yu-Hu; Nie, Lei

2009-05-15

By monitoring the road and construction dust fall continuously during the "Good Luck Beijing" sport events, the reduction of road and construction dust fall caused by traffic restriction was studied. The contribution rate of road and construction dust to particulate matter of Beijing atmosphere environment, and the emission ratio of it to total local PM10 emission were analyzed. The results show that the traffic restriction reduces road and construction dust fall significantly. The dust fall average value of ring roads was 0.27 g x (m2 x d)(-1) in the "traffic restriction" period, and the values were 0.81 and 0.59 g x (m2 x d)(-1) 1 month and 7 days before. The dust fall average value of major arterial and minor arterial was 0.21 g x (m2 x d)(-1) in the "traffic restriction" period, and the values were 0.54 and 0.58 g x (m2 x d)(-1) 1 month and 7 days before. The roads emission reduced 60%-70% compared with before traffic restriction. The dust fall average values of civil architecture and utility architecture were 0.61 and 1.06 g x (m2 x d)(-1) in the "traffic restriction" period, and the values were 1.15 and 1.55 g x (m2 x d)(-1) 20 days before. The construction dust reduced 30%-47% compared with 20 days before traffic restriction. Road and construction dust emission are the main source of atmosphere particulate matter in Beijing, and its contribution to ambient PM10 concentration is 21%-36%. PM10 emitted from roads and constructions account for 42%-72% and 30%-51% of local emission while the local PM10 account for 50% and 70% of the total emission.

Health aspects of wood particles in fugitive emission during professional exposition

International Nuclear Information System (INIS)

Vlckova, H.; Schwarz, M.; Lalik, V.

2008-01-01

Fugitive emission of wood dust can constitute serious menace to health of worker in wood industry. Present paper describes not only influence of unaccompanied wood which develops allergic reactions, respire diseases, dermatosis, cancer etc., but also additional effects of natural wood components as endotoxins, microbial spores, amoebas, fungus, animal and proteins, volatile components wood resins, respectively. (authors)

Study on reinforcement of soil for suppressing fugitive dust by bio-cementitious material

Science.gov (United States)

Zhan, Qiwei; Qian, Chunxiang

2017-06-01

Microbial-induced reinforcement of soil, as a new green and environmental-friendly method, is being paid extensive attention to in that it has low cost, simple operation and rapid effects. In this research, reinforcement of soil for suppressing fugitive dust by bio-cementitious material was investigated. Soil cemented by bio-cementitious material had superior mechanical properties, such as hardness, compressive strength, microstructure, wind-erosion resistance, rainfall-erosion resistance and freeze-thaw resistance. The average hardness of sandy soil, floury soil and clay soil is 18.9 º, 25.2 º and 26.1 º, while average compressive strength of samples is 0.43 MPa, 0.54 MPa and 0.69 MPa, respectively; meanwhile, the average calcite content of samples is 6.85 %, 6.09 %, and 5.96 %, respectively. Compared with the original sandy soil, floury soil and clay soil, the porosity decreases by 38.5 %, 33.7 % and 29.2 %. When wind speed is 12 m/s, the mass loss of sandy soil, floury soil and clay soil cemented by bio-cementitious material are all less than 30 g/(m2·h). After three cycles of rainfall erosion of 2.5 mm/h, the mass loss are less than 25 g/(m2·h) and the compressive strength residual ratio are more than 98.0 %. Under 25 cycles of freeze-thaw, the mass loss ratio are less than 3.0 %.

Directional passive ambient air monitoring of ammonia for fugitive source attribution; a field trial with wind tunnel characteristics

Science.gov (United States)

Solera García, M. A.; Timmis, R. J.; Van Dijk, N.; Whyatt, J. D.; Leith, I. D.; Leeson, S. R.; Braban, C. F.; Sheppard, L. J.; Sutton, M. A.; Tang, Y. S.

2017-10-01

Atmospheric ammonia is a precursor for secondary particulate matter formation, which harms human health and contributes to acidification and eutrophication. Under the 2012 Gothenburg Protocol, 2005 emissions must be cut by 6% by 2020. In the UK, 83% of total emissions originate from agricultural practices such as fertilizer use and rearing of livestock, with emissions that are spatially extensive and variable in nature. Such fugitive emissions make resolving and tracking of individual site performance challenging. The Directional Passive Air quality Sampler (DPAS) was trialled at Whim Bog, an experimental site with a wind-controlled artificial release of ammonia, in combination with CEH-developed ammonia samplers. Whilst saturation issues were identified, two DPAS-MANDE (Mini Annular Denuder) systems, when deployed in parallel, displayed an average relative deviation of 15% (2-54%) across all 12 directions, with the directions exposed to the ammonia source showing ∼5% difference. The DPAS-MANDE has shown great potential for directional discrimination and can contribute to the understanding and management of fugitive ammonia sources from intensive agriculture sites.

PERSPECTIVE: Dust, fertilization and sources

Science.gov (United States)

Remer, Lorraine A.

2006-11-01

fraction that arrives at another continent [2]. At the deposition end of the chain, it is still unclear how the limited minerals in the dust such as iron are released for uptake by organisms either on land or in the ocean. Not all dust deposited into oceans results in a phytoplankton bloom. The process requires a chemical pathway that mobilizes a fraction of the iron into soluble form. Meskhidze et al [3] show that phytoplankton blooms following dust transport from the Gobi desert in Asia into the Pacific ocean result in a phytoplankton bloom only if the dust is accompanied by high initial SO2-to-dust ratios, suggesting that sulfuric acid coatings on the dust particle mobilize the embedded iron in the dust for phytoplankton uptake. Quantifying transport, deposition and nutrient availability are the latter ends of a puzzle that must begin by identifying and quantifying dust emission at the sources. The emission process is complex at the microscale requiring the right conditions for saltation and bombardment, which makes identification and inclusion of sources in global transport models very difficult. The result is that estimates of annual global dust emissions range from 1000 to 3000 Tg per year [4]. Even as global estimates of dust emissions are uncertain, localizing the sources brings even greater uncertainty. It has been recognized for several years that dust sources are not uniformly distributed over the arid regions of the Earth, but are regulated to topographic lows associated with dried lake deposits [5]. Using aerosol information from satellites, a comprehensive map of the world's source regions shows sources localized to specific areas of the Earth's arid regions [6]. Still these maps suggest broad emission sources covering several degrees of latitude and longitude. In the paper by Koren and co-authors [7] appearing in this issue, one particular dust source, the Bodélé depression in Chad, is analyzed in detail. They find that the specific topography of the

Identifying sources of aeolian mineral dust: Present and past

Science.gov (United States)

Muhs, Daniel R; Prospero, Joseph M; Baddock, Matthew C; Gill, Thomas E

2014-01-01

Aeolian mineral dust is an important component of the Earth’s environmental systems, playing roles in the planetary radiation balance, as a source of fertilizer for biota in both terrestrial and marine realms and as an archive for understanding atmospheric circulation and paleoclimate in the geologic past. Crucial to understanding all of these roles of dust is the identification of dust sources. Here we review the methods used to identify dust sources active at present and in the past. Contemporary dust sources, produced by both glaciogenic and non-glaciogenic processes, can be readily identified by the use of Earth-orbiting satellites. These data show that present dust sources are concentrated in a global dust belt that encompasses large topographic basins in low-latitude arid and semiarid regions. Geomorphic studies indicate that specific point sources for dust in this zone include dry or ephemeral lakes, intermittent stream courses, dune fields, and some bedrock surfaces. Back-trajectory analyses are also used to identify dust sources, through modeling of wind fields and the movement of air parcels over periods of several days. Identification of dust sources from the past requires novel approaches that are part of the geologic toolbox of provenance studies. Identification of most dust sources of the past requires the use of physical, mineralogical, geochemical, and isotopic analyses of dust deposits. Physical properties include systematic spatial changes in dust deposit thickness and particle size away from a source. Mineralogy and geochemistry can pinpoint dust sources by clay mineral ratios and Sc-Th-La abundances, respectively. The most commonly used isotopic methods utilize isotopes of Nd, Sr, and Pb and have been applied extensively in dust archives of deep-sea cores, ice cores, and loess. All these methods have shown that dust sources have changed over time, with far more abundant dust supplies existing during glacial periods. Greater dust supplies in

75 FR 39365 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

Science.gov (United States)

2010-07-08

... coarse particulate matter (PM 10 ) emissions from sources of fugitive dust such as construction sites... because some provisions of the rules conflict with the CAA section 110(a) requirement that SIP rules must... also discuss our determination of which fugitive dust source categories addressed by Regulation VIII...

Fugitive emissions from nanopowder manufacturing

International Nuclear Information System (INIS)

Trompetter, W. J.; Ancelet, T.; Davy, P. K.; Kennedy, J.

2016-01-01

In response to health and safety questions and concerns regarding particulate matter emissions from equipment used for synthesizing NiFe and TiO 2 nanopowders, a study was undertaken to assess their impact on the air quality inside and outside a laboratory where the manufacturing equipment is operated. Elemental concentrations determined by ion beam analysis (IBA) of air particulate matter (PM) samples collected hourly with a Streaker TM sampler were used to identify possible sources and estimate contributions from nanopowder production and other sources. The fugitive nanopowder emissions were the highest at the indoor sampling location when powders were being manufactured. Average fugitive emissions of 210 ng m −3 (1-h average) (maximum 2163 ng m −3 1-h average) represented 2 % (maximum 20 %) of the average PM collected (9359 ng m −3 1-h average). The measured NiFe alloy or TiO 2 PM concentrations were much smaller than the 8-h time-weighted average (TWA) workplace exposure standards (WES) for these materials (≥1,000,000 ng m −3 ). Most PM was found to be from infiltrated outdoor ambient sources. This suggests that nanopowder production in the laboratory is not likely to have adverse health effects on individuals using the equipment, although further improvements can be made to further limit exposure.Graphical abstract

Atmospheric Fate and Transport of Agricultural Dust and Ammonia

Science.gov (United States)

Hiranuma, N.; Brooks, S. D.; Thornton, D. C.; Auvermann, B. W.; Fitz, D. R.

2008-12-01

Agricultural fugitive dust and odor are significant sources of localized air pollution in the semi-arid southern Great Plains. Daily episodes of ground-level fugitive dust emissions from the cattle feedlots associated with increased cattle activity in the early evenings are routinely observed, while consistently high ammonia is observed throughout the day. Here we present measurements of aerosol size distributions and concentrations of gas and particulate phase ammonia species collected at a feedlot in Texas during summers of 2006, 2007 and 2008. A GRIMM sequential mobility particle sizer and GRIMM 1.108 aerosol spectrometer were used to determine aerosol size distributions in the range of 10 nm to 20 µm aerodynamic diameter at the downwind and upwind edges of the facility. Using aqueous scrubbers, simultaneous measurements of both gas phase and total ammonia species present in the gas and particle phases were also collected. In addition to the continuous measurements at the edges of the facility, coincident aerosol and ammonia measurements were obtain at an additional site further downwind (~3.5 km). Taken together our measurements will be used to quantify aerosol and ammonia dispersion and transport. Relationships between the fate and transport of the aerosols and ammonia will be discussed.

Effect of Vehicle Characteristics on Unpaved Road Dust Emissions

National Research Council Canada - National Science Library

Gillies, J. A; Etyemezian, V; Kuhns, H; Nikolic, D; Gillette, D. A

2005-01-01

This paper presents PM10 fugitive dust emission factors for a range of vehicles types and examines the influence of vehicle and wake characteristics on the strength of emissions from an unpaved road...

Fugitive emissions from nanopowder manufacturing

Energy Technology Data Exchange (ETDEWEB)

Trompetter, W. J., E-mail: b.trompetter@gns.cri.nz; Ancelet, T.; Davy, P. K.; Kennedy, J. [GNS Science (New Zealand)

2016-07-15

In response to health and safety questions and concerns regarding particulate matter emissions from equipment used for synthesizing NiFe and TiO{sub 2} nanopowders, a study was undertaken to assess their impact on the air quality inside and outside a laboratory where the manufacturing equipment is operated. Elemental concentrations determined by ion beam analysis (IBA) of air particulate matter (PM) samples collected hourly with a Streaker{sup TM} sampler were used to identify possible sources and estimate contributions from nanopowder production and other sources. The fugitive nanopowder emissions were the highest at the indoor sampling location when powders were being manufactured. Average fugitive emissions of 210 ng m{sup −3} (1-h average) (maximum 2163 ng m{sup −3} 1-h average) represented 2 % (maximum 20 %) of the average PM collected (9359 ng m{sup −3} 1-h average). The measured NiFe alloy or TiO{sub 2} PM concentrations were much smaller than the 8-h time-weighted average (TWA) workplace exposure standards (WES) for these materials (≥1,000,000 ng m{sup −3}). Most PM was found to be from infiltrated outdoor ambient sources. This suggests that nanopowder production in the laboratory is not likely to have adverse health effects on individuals using the equipment, although further improvements can be made to further limit exposure.Graphical abstract.

Spatiotemporal variations of ambient PM10 source contributions in Beijing in 2004 using positive matrix factorization

Directory of Open Access Journals (Sweden)

T. Chen

2008-05-01

Full Text Available Source contributions to ambient PM10 (particles with an aerodynamic diameter of 10 μm or less in Beijing, China were determined with positive matrix factorization (PMF based on ambient PM10 composition data including concentrations of organic carbon (OC, elemental carbon (EC, ions and metal elements, which were simultaneously obtained at six sites through January, April, July and October in 2004. Results from PMF indicated that seven major sources of ambient PM10 were urban fugitive dust, crustal soil, coal combustion, secondary sulfate, secondary nitrate, biomass burning with municipal incineration, and vehicle emission, respectively. In paticular, urban fugitive dust and crustal soil as two types of dust sources with similar chemical characteristics were differentiated by PMF. Urban fugitive dust contributed the most, accounting for 34.4% of total PM10 mass on an annual basis, with relatively high contributions in all four months, and even covered 50% in April. It also showed higher contributions in southwestern and southeastern areas than in central urban areas. Coal combustion was found to be the primary contributor in January, showing higher contributions in urban areas than in suburban areas with seasonal variation peaking in winter, which accounted for 15.5% of the annual average PM10 concentration. Secondary sulfate and secondary nitrate combined as the largest contributor to PM10 in July and October, with strong seasonal variation peaking in summer, accounting for 38.8% and 31.5% of the total PM10 mass in July and October, respectively. Biomass burning with municipal incineration contributions were found in all four months and accounted for 9.8% of the annual average PM10 mass concentration, with obviously higher contribution in October than in other months. Incineration sources were probably located in southwestern Beijing. Contribution from vehicle emission accounted for 5.0% and exhibited no significant seasonal variation. In sum

Fugitive methane emissions from an agricultural biodigester

International Nuclear Information System (INIS)

Flesch, Thomas K.; Desjardins, Raymond L.; Worth, Devon

2011-01-01

The use of agricultural biodigesters provides a strategy for reducing greenhouse gas (GHG) emissions while generating energy. The GHG reduction associated with a biodigester will be affected by fugitive emissions from the facility. The objective of this study was to measure fugitive methane (CH 4 ) emissions from a Canadian biodigester. The facility uses anaerobic digestion to produce biogas from cattle manure and other organic feedstock, which is burnt to generate electricity (1 MW capacity) and heat. An inverse dispersion technique was used to calculate emissions. Fugitive emissions were related to the operating state of the biodigester, and over four seasonal campaigns the emission rate averaged 3.2, 0.8, and 26.6 kg CH 4 hr -1 for normal operations, maintenance, and flaring periods, respectively. During normal operations the average fugitive emission rate corresponded to 3.1% of the CH 4 gas production rate. -- Highlights: → Biodigesters reduce greenhouse gas emissions. → Net emission reduction affected by fugitive emissions. → Fugitive CH 4 measured at agricultural biodigester (1 MW generating capacity). → Emissions were 3.1% of gas production. → Emissions lower than assumed in carbon credit protocols.

Kuiper Belt Dust Grains as a Source of Interplanetary Dust Particles

Science.gov (United States)

Liou, Jer-Chyi; Zook, Herbert A.; Dermott, Stanley F.

1996-01-01

The recent discovery of the so-called Kuiper belt objects has prompted the idea that these objects produce dust grains that may contribute significantly to the interplanetary dust population. In this paper, the orbital evolution of dust grains, of diameters 1 to 9 microns, that originate in the region of the Kuiper belt is studied by means of direct numerical integration. Gravitational forces of the Sun and planets, solar radiation pressure, as well as Poynting-Robertson drag and solar wind drag are included. The interactions between charged dust grains and solar magnetic field are not considered in the model. Because of the effects of drag forces, small dust grains will spiral toward the Sun once they are released from their large parent bodies. This motion leads dust grains to pass by planets as well as encounter numerous mean motion resonances associated with planets. Our results show that about 80% of the Kuiper belt grains are ejected from the Solar System by the giant planets, while the remaining 20% of the grains evolve all the way to the Sun. Surprisingly, the latter dust grains have small orbital eccentricities and inclinations when they cross the orbit of the Earth. This makes them behave more like asteroidal than cometary-type dust particles. This also enhances their chances of being captured by the Earth and makes them a possible source of the collected interplanetary dust particles; in particular, they represent a possible source that brings primitive/organic materials from the outer Solar System to the Earth. When collisions with interstellar dust grains are considered, however, Kuiper belt dust grains around 9 microns appear likely to be collisionally shattered before they can evolve toward the inner part of the Solar System. The collision destruction can be applied to Kuiper belt grains up to about 50 microns. Therefore, Kuiper belt dust grains within this range may not be a significant part of the interplanetary dust complex in the inner Solar

Dust emissions from unpaved roads on the Colorado Plateau

Science.gov (United States)

Duniway, M.; Flagg, C.; Belnap, J.

2013-12-01

), the minimum wind velocity required to initiate erosion, and sediment production were also quantified using a portable wind tunnel at monitoring sites. Additionally, numerous characteristics including gravel cover, particle-size distribution, soil compaction, and loose-erodible material were measured on road surfaces at monitoring sites. Preliminary results suggest that roads are an important regional dust source, as emissions from roads are comparable to non-road, rural sources that are being monitored concurrently. While gravel roads produce more dust per day on average, per vehicle emissions are larger on dirt roads. Dust flux decreases with distance from the road edge on all road types, however this decline is less pronounced on dirt roads. Portable wind tunnel results indicate that TFV is consistently lower on dirt versus gravel roads across all soil types. Fugitive dust flux is generally larger and more variable on dirt roads compared to gravel roads. Initial analyses suggest that several easily measurable road surface characteristics can potentially be used to predict both TFV and sediment production, including: total gravel cover, gravel particle-size classes, clay content, and road compaction. The relation between TFV and total gravel cover in particular appears to be non-linear, with TFV increasing rapidly above ~40% gravel cover.

PROBLEMS WITH DETERMINATION OF FUGITIVE EMISSION OF POLYCYCLIC AROMATIC HYDROCARBONS FROM COKE OVEN BATTERY

Directory of Open Access Journals (Sweden)

Rafał Bigda

2017-03-01

Full Text Available Coke oven battery is complex and multifaceted facility in terms of air pollutant emissions. As far as stack or quenching tower does not cause major difficulties of emission measurement, the fugitive emission measurement from sources such as battery top elements (charging holes, ascension pipes or oven doors is still complicated and not fully solved problem. This article presents the discussion concerning main problems and errors likely to be made in particular stages of procedure of fugitive emissions characterization from coke oven battery (selection of sampling points, sampling itself, measurement of air velocity over battery top and laboratory analyses. In addition, results of concentrations measurements of selected substances characteristic for the coking process (naphthalene, anthracene, 4 PAHs and TSP originating from fugitive sources of coke oven battery and subjected to reporting under the E-PRTR are presented. The measurements were carried out on coke oven battery top in points selected on the basis of the preceding detailed air convection velocity measurements over battery top. Results of the velocity measurements were compared with results of numerical modelling using CFD software. The presented material is an attempt to cross-sectional presentation of issues related to the quantitative evaluation of fugitive emission from coke oven battery, discussed on the example of PAHs emission as a group of substances characteristic for coking of coal.

Early-Holocene greening of the Afro-Asian dust belt changed sources of mineral dust in West Asia

Science.gov (United States)

Sharifi, Arash; Murphy, Lisa N.; Pourmand, Ali; Clement, Amy C.; Canuel, Elizabeth A.; Naderi Beni, Abdolmajid; Lahijani, Hamid A. K.; Delanghe, Doriane; Ahmady-Birgani, Hesam

2018-01-01

Production, transport and deposition of mineral dust have significant impacts on different components of the Earth systems through time and space. In modern times, dust plumes are associated with their source region(s) using satellite and land-based measurements and trajectory analysis of air masses through time. Reconstruction of past changes in the sources of mineral dust as related to changes in climate, however, must rely on the knowledge of the geochemical and mineralogical composition of modern and paleo-dust, and that of their potential source origins. In this contribution, we present a 13,000-yr record of variations in radiogenic Sr-Nd-Hf isotopes and Rare Earth Element (REE) anomalies as well as dust grain size from an ombrotrophic (rain fed) peat core in NW Iran as proxies of past changes in the sources of dust over the interior of West Asia. Our data shows that although the grain size of dust varies in a narrow range through the entire record, the geochemical fingerprint of dust particles deposited during the low-flux, early Holocene period (11,700-6,000 yr BP) is distinctly different from aerosols deposited during high dust flux periods of the Younger Dryas and the mid-late Holocene (6,000-present). Our findings indicate that the composition of mineral dust deposited at the study site changed as a function of prevailing atmospheric circulation regimes and land exposure throughout the last deglacial period and the Holocene. Simulations of atmospheric circulation over the region show the Northern Hemisphere Summer Westerly Jet was displaced poleward across the study area during the early Holocene when Northern Hemisphere insolation was higher due to the Earth's orbital configuration. This shift, coupled with lower dust emissions simulated based on greening of the Afro-Asian Dust Belt during the early Holocene likely led to potential sources in Central Asia dominating dust export to West Asia during this period. In contrast, the dominant western and

Dust deposition in southern Nevada and California, 1984-1989: Relations to climate, source area, and source lithology

Science.gov (United States)

Reheis, Marith C.; Kihl, Rolf

1995-05-01

Dust samples collected annually for 5 years from 55 sites in southern Nevada and California provide the first regional source of information on modern rates of dust deposition, grain size, and mineralogical and chemical composition relative to climate and to type and lithology of dust source. The average silt and clay flux (rate of deposition) in southern Nevada and southeastern California ranges from 4.3 to 15.7 g/m2/yr, but in southwestern California the average silt and clay flux is as high as 30 g/m2/yr. The climatic factors that affect dust flux interact with each other and with the factors of source type (playas versus alluvium), source lithology, geographic area, and human disturbance. Average dust flux increases with mean annual temperature but is not correlated to decreases in mean annual precipitation because the regional winds bring dust to relatively wet areas. In contrast, annual dust flux mostly reflects changes in annual precipitation (relative drought) rather than temperature. Although playa and alluvial sources produce about the same amount of dust per unit area, the total volume of dust from the more extensive alluvial sources is much larger. In addition, playa and alluvial sources respond differently to annual changes in precipitation. Most playas produce dust that is richer in soluble salts and carbonate than that from alluvial sources (except carbonate-rich alluvium). Gypsum dust may be produced by the interaction of carbonate dust and anthropogenic or marine sulfates. The dust flux in an arid urbanizing area may be as much as twice that before disturbance but decreases when construction stops. The mineralogic and major-oxide composition of the dust samples indicates that sand and some silt is locally derived and deposited, whereas clay and some silt from different sources can be far-traveled. Dust deposited in the Transverse Ranges of California by the Santa Ana winds appears to be mainly derived from sources to the north and east.

Air quality dispersion models from energy sources

International Nuclear Information System (INIS)

Lazarevska, Ana

1996-01-01

Along with the continuing development of new air quality models that cover more complex problems, in the Clean Air Act, legislated by the US Congress, a consistency and standardization of air quality model applications were encouraged. As a result, the Guidelines on Air Quality Models were published, which are regularly reviewed by the Office of Air Quality Planning and Standards, EPA. These guidelines provide a basis for estimating the air quality concentrations used in accessing control strategies as well as defining emission limits. This paper presents a review and analysis of the recent versions of the models: Simple Terrain Stationary Source Model; Complex Terrain Dispersion Model; Ozone,Carbon Monoxide and Nitrogen Dioxide Models; Long Range Transport Model; Other phenomenon Models:Fugitive Dust/Fugitive Emissions, Particulate Matter, Lead, Air Pathway Analyses - Air Toxic as well as Hazardous Waste. 8 refs., 4 tabs., 2 ills

Development of High-Resolution Dynamic Dust Source Function - A Case Study with a Strong Dust Storm in a Regional Model

Science.gov (United States)

Kim, Dongchul; Chin, Mian; Kemp, Eric M.; Tao, Zhining; Peters-Lidard, Christa D.; Ginoux, Paul

2017-01-01

A high-resolution dynamic dust source has been developed in the NASA Unified-Weather Research and Forecasting (NU-WRF) model to improve the existing coarse static dust source. In the new dust source map, topographic depression is in 1-km resolution and surface bareness is derived using the Normalized Difference Vegetation Index (NDVI) data from Moderate Resolution Imaging Spectroradiometer (MODIS). The new dust source better resolves the complex topographic distribution over the Western United States where its magnitude is higher than the existing, coarser resolution static source. A case study is conducted with an extreme dust storm that occurred in Phoenix, Arizona in 0203 UTC July 6, 2011. The NU-WRF model with the new high-resolution dynamic dust source is able to successfully capture the dust storm, which was not achieved with the old source identification. However the case study also reveals several challenges in reproducing the time evolution of the short-lived, extreme dust storm events.

Development of High-Resolution Dynamic Dust Source Function -A Case Study with a Strong Dust Storm in a Regional Model.

Science.gov (United States)

Kim, Dongchul; Chin, Mian; Kemp, Eric M; Tao, Zhining; Peters-Lidard, Christa D; Ginoux, Paul

2017-06-01

A high-resolution dynamic dust source has been developed in the NASA Unified-Weather Research and Forecasting (NU-WRF) model to improve the existing coarse static dust source. In the new dust source map, topographic depression is in 1-km resolution and surface bareness is derived using the Normalized Difference Vegetation Index (NDVI) data from Moderate Resolution Imaging Spectroradiometer (MODIS). The new dust source better resolves the complex topographic distribution over the Western United States where its magnitude is higher than the existing, coarser resolution static source. A case study is conducted with an extreme dust storm that occurred in Phoenix, Arizona in 02-03 UTC July 6, 2011. The NU-WRF model with the new high-resolution dynamic dust source is able to successfully capture the dust storm, which was not achieved with the old source identification. However the case study also reveals several challenges in reproducing the time evolution of the short-lived, extreme dust storm events.

Fugitive emission source characterization using a gradient-based optimization scheme and scalar transport adjoint

Science.gov (United States)

Brereton, Carol A.; Joynes, Ian M.; Campbell, Lucy J.; Johnson, Matthew R.

2018-05-01

Fugitive emissions are important sources of greenhouse gases and lost product in the energy sector that can be difficult to detect, but are often easily mitigated once they are known, located, and quantified. In this paper, a scalar transport adjoint-based optimization method is presented to locate and quantify unknown emission sources from downstream measurements. This emission characterization approach correctly predicted locations to within 5 m and magnitudes to within 13% of experimental release data from Project Prairie Grass. The method was further demonstrated on simulated simultaneous releases in a complex 3-D geometry based on an Alberta gas plant. Reconstructions were performed using both the complex 3-D transient wind field used to generate the simulated release data and using a sequential series of steady-state RANS wind simulations (SSWS) representing 30 s intervals of physical time. Both the detailed transient and the simplified wind field series could be used to correctly locate major sources and predict their emission rates within 10%, while predicting total emission rates from all sources within 24%. This SSWS case would be much easier to implement in a real-world application, and gives rise to the possibility of developing pre-computed databases of both wind and scalar transport adjoints to reduce computational time.

OPEN PATH TUNABLE DIODE LASER ABSORPTION SPECTROSCOPY FOR ACQUISITION OF FUGITIVE EMISSION FLUX DATA

Science.gov (United States)

Air pollutant emission from unconfined sources is an increasingly important environmental issue. The U.S. EPA has developed a gorund-based optical remote sensing method that enables direct measurement of fugitive emission flux from large area sources. Open-path Fourier transfor...

Test plan for FY-91 dust control studies

International Nuclear Information System (INIS)

Winberg, M.R.

1991-03-01

This test plan defines basic test procedures for testing commercially available vendor products as soil fixatives and dust suppression agents to determine their capability to control fugitive dust generation during transuranic waste retrieval and handling operations. A description of the test apparatus and methods are provided in this test plan. This test plan defines the sampling procedures, controls, and analytical methods for the samples collected. Data management is discussed, as well as quality assurance and safety requirements for the study. 6 refs., 5 figs

Geochemical evidence for diversity of dust sources in the southwestern United States

Science.gov (United States)

Reheis, M.C.; Budahn, J.R.; Lamothe, P.J.

2002-01-01

Several potential dust sources, including generic sources of sparsely vegetated alluvium, playa deposits, and anthropogenic emissions, as well as the area around Owens Lake, California, affect the composition of modern dust in the southwestern United States. A comparison of geochemical analyses of modern and old (a few thousand years) dust with samples of potential local sources suggests that dusts reflect four primary sources: (1) alluvial sediments (represented by Hf, K, Rb, Zr, and rare-earth elements, (2) playas, most of which produce calcareous dust (Sr, associated with Ca), (3) the area of Owens (dry) Lake, a human-induced playa (As, Ba, Li, Pb, Sb, and Sr), and (4) anthropogenic and/or volcanic emissions (As, Cr, Ni, and Sb). A comparison of dust and source samples with previous analyses shows that Owens (dry) Lake and mining wastes from the adjacent Cerro Gordo mining district are the primary sources of As, Ba, Li, and Pb in dusts from Owens Valley. Decreases in dust contents of As, Ba, and Sb with distance from Owens Valley suggest that dust from southern Owens Valley is being transported at least 400 km to the east. Samples of old dust that accumulated before European settlement are distinctly lower in As, Ba, and Sb abundances relative to modern dust, likely due to modern transport of dust from Owens Valley. Thus, southern Owens Valley appears to be an important, geochemically distinct, point source for regional dust in the southwestern United States. Copyright ?? 2002 Elsevier Science Ltd.

Advanced receptor modelling for the apportionment of road dust resuspension to atmospheric PM

Science.gov (United States)

Amato, F.; Pandolfi, M.; Escrig, A.; Querol, X.; Alastuey, A.; Pey, J.; Perez, N.; Hopke, P. K.

2009-04-01

Fugitive emissions from traffic resuspension can often represent an important source of atmospheric particulate matter in urban environments, especially when the scarce precipitations favour the accumulation of road dust. Resuspension of road dust can lead to high exposures to heavy metals, metalloids and mineral matter. Knowing the amount of its contribution to atmospheric PM is a key task for establishing eventual mitigation or preventive measures. Factor analysis techniques are widely used tools for atmospheric aerosol source apportionment, based on the mass conservation principle. Paatero and Tapper (1993) suggested the use of a Weighted Least Squares scheme with the aim of obtaining a minimum variance solution. Additionally they proposed to incorporate the basic physical constraint of non negativity, calling their approach Positive Matrix Factorization (PMF), which can be performed by the program PMF2 released by Paatero (1997). Nevertheless, Positive Matrix Factorization can be either solved with the Multilinear Engine (ME-2), a more flexible program, also developed by Paatero (1999), which can solve any model consisting in sum of products of unknowns. The main difference with PMF2 is that ME-2 does not solve only well-defined tasks, but its actions are defined in a "script file" written in a special-purpose programming language, allowing incorporating additional tasks such as data processing etc. Thus in ME-2 a priori information, e.g. chemical fingerprints can be included as auxiliary terms of the object function to be minimized. This feature of ME-2 make it especially suitable for source apportionment studies where some knowledge (chemical ratios, profiles, mass conservation etc) of involved sources is available. The aim of this study was to quantify the contribution of road dust resuspension in PM10, PM2.5 and PM1 data set from Barcelona (Spain). Given that recently the emission profile of local road dust was characterized (Amato et al., in press

Emission Inventory for Fugitive Emissions in Denmark

DEFF Research Database (Denmark)

Plejdrup, Marlene Schmidt; Nielsen, Ole-Kenneth; Nielsen, Malene

This report presents the methodology and data used in the Danish inventory of fugitive emissions from fuels for the years until 2007. The inventory of fugitive emissions includes CO2, CH4, N2O, NOx, CO, NMVOC, SO2, dioxin, PAH and particulate matter. In 2007 the total Danish emission of greenhouse...

Long-term dust aerosol production from natural sources in Iceland.

Science.gov (United States)

Dagsson-Waldhauserova, Pavla; Arnalds, Olafur; Olafsson, Haraldur

2017-02-01

Iceland is a volcanic island in the North Atlantic Ocean with maritime climate. In spite of moist climate, large areas are with limited vegetation cover where >40% of Iceland is classified with considerable to very severe erosion and 21% of Iceland is volcanic sandy deserts. Not only do natural emissions from these sources influenced by strong winds affect regional air quality in Iceland ("Reykjavik haze"), but dust particles are transported over the Atlantic ocean and Arctic Ocean >1000 km at times. The aim of this paper is to place Icelandic dust production area into international perspective, present long-term frequency of dust storm events in northeast Iceland, and estimate dust aerosol concentrations during reported dust events. Meteorological observations with dust presence codes and related visibility were used to identify the frequency and the long-term changes in dust production in northeast Iceland. There were annually 16.4 days on average with reported dust observations on weather stations within the northeastern erosion area, indicating extreme dust plume activity and erosion within the northeastern deserts, even though the area is covered with snow during the major part of winter. During the 2000s the highest occurrence of dust events in six decades was reported. We have measured saltation and Aeolian transport during dust/volcanic ash storms in Iceland, which give some of the most intense wind erosion events ever measured. Icelandic dust affects the ecosystems over much of Iceland and causes regional haze. It is likely to affect the ecosystems of the oceans around Iceland, and it brings dust that lowers the albedo of the Icelandic glaciers, increasing melt-off due to global warming. The study indicates that Icelandic dust may contribute to the Arctic air pollution. Long-term records of meteorological dust observations from Northeast Iceland indicate the frequency of dust events from Icelandic deserts. The research involves a 60-year period and

Geochemical characterization of critical dust source regions in the American West

Science.gov (United States)

Aarons, Sarah M.; Blakowski, Molly A.; Aciego, Sarah M.; Stevenson, Emily I.; Sims, Kenneth W. W.; Scott, Sean R.; Aarons, Charles

2017-10-01

The generation, transport, and deposition of mineral dust are detectable in paleoclimate records from land, ocean, and ice, providing valuable insight into earth surface conditions and cycles on a range of timescales. Dust deposited in marine and terrestrial ecosystems can provide critical nutrients to nutrient-limited ecosystems, and variations in dust provenance can indicate changes in dust production, sources and transport pathways as a function of climate variability and land use change. Thus, temporal changes in locations of dust source areas and transport pathways have implications for understanding interactions between mineral dust, global climate, and biogeochemical cycles. This work characterizes dust from areas in the American West known for dust events and/or affected by increasing human settlement and livestock grazing during the last 150 years. Dust generation and uplift from these dust source areas depends on climate and land use practices, and the relative contribution of dust has likely changed since the expansion of industrialization and agriculture into the western United States. We present elemental and isotopic analysis of 28 potential dust source area samples analyzed using Thermal Ionization Mass Spectrometry (TIMS) for 87Sr/86Sr and 143Nd/144Nd composition and Multi-Collector Inductively Coupled Plasma Mass Spectrometer (MC-ICPMS) for 176Hf/177Hf composition, and ICPMS for major and trace element concentrations. We find significant variability in the Sr, Nd, and Hf isotope compositions of potential source areas of dust throughout western North America, ranging from 87Sr/86Sr = 0.703699 to 0.740236, εNd = -26.6 to 2.4, and εHf = -21.7 to -0.1. We also report differences in the trace metal and phosphorus concentrations in the geologic provinces sampled. This research provides an important resource for the geochemical tracing of dust sources and sinks in western North America, and will aid in modeling the biogeochemical impacts of increased

The Southern Kalahari: a potential new dust source in the Southern Hemisphere?

International Nuclear Information System (INIS)

Bhattachan, Abinash; D’Odorico, Paolo; Baddock, Matthew C; Zobeck, Ted M; Okin, Gregory S; Cassar, Nicolas

2012-01-01

Most sources of atmospheric dust on Earth are located in the Northern Hemisphere. The lower dust emissions in the Southern Hemisphere in part limit the supply of micronutrients (primarily soluble iron) to the Southern Ocean, thereby constraining its productivity. Climate and land use change can alter the current distribution of dust source regions on Earth. Can new dust sources be activated in the Southern Hemisphere? Here we show that vegetation loss and dune remobilization in the Southern Kalahari can promote dust emissions comparable to those observed from major contemporary dust sources in the Southern African region. Dust generation experiments support the hypothesis that, in the Southern Kalahari, aeolian deposits that are currently mostly stabilized by savanna vegetation are capable of emitting substantial amounts of dust from interdune areas. We show that dust from these areas is relatively rich in soluble iron, an important micronutrient for ocean productivity. Trajectory analyses show that dust from the Kalahari commonly reaches the Southern Ocean and could therefore enhance its productivity. (letter)

40 CFR 49.126 - Rule for limiting fugitive particulate matter emissions.

Science.gov (United States)

2010-07-01

... amount of fugitive particulate matter that may be emitted from certain air pollution sources operating... minimize the accumulation of dusty materials that have the potential to become airborne, and the prompt... materials likely to become airborne. (viii) The prompt removal from paved streets of earth or other material...

A comparison of models to assess the atmospheric dispersion of resuspended radionuclides on the Nevada Test Site

International Nuclear Information System (INIS)

Green, J.R.; Eckart, R.E.

1994-11-01

A study of computer codes was made to determine the suitability of their use for modeling radionuclide dispersion from attachment to fugitive dust at the GMX safety shot area of the Nevada Test site. Two codes, the Industrial Source Complex 2 Long Term Model (ISCLT2) and the Fugitive Dust Model (FDM), were subsequently chosen to model the GMX site. Dose calculations were performed using the output values generated by the computer codes. The concentration values produced by the two codes were within a factor of two of each other and were not significantly different. The FDM, however, was felt to be a more useful code for use in calculating doses caused by attachment to fugitive dust

Dust control products at Hagerman National Wildlife Refuge, Texas: environmental safety and performance

Science.gov (United States)

Kunz, Bethany K.; Little, Edward E.

2015-01-01

Controlling fugitive dust while protecting natural resources is a challenge faced by all managers of unpaved roads. Unfortunately, road managers choosing between dust control products often have little objective environmental information to aid their decisions. To address this information gap, the U.S. Geological Survey and the U.S. Fish and Wildlife Service collaborated on a field test of three dust control products with the objectives of (a) evaluating product performance under real-world conditions, (b) verifying the environmental safety of products identified as practically nontoxic in laboratory tests, and (c) testing the feasibility of several environmental monitoring techniques for use in dust control tests. In cooperation with refuge staff and product vendors, three products (one magnesium chloride plus binder, one cellulose, and one synthetic fluid plus binder) were applied in July 2012 to replicated road sections at the Hagerman National Wildlife Refuge in Texas. These sections were monitored periodically for 12 months after application. Product performance was assessed by mobile-mounted particulate-matter meters measuring production of fugitive dust and by observations of road conditions. Environmental safety was evaluated through on-site biological observations and leaching tests with samples of treated aggregate. All products reduced dust and improved surface condition during those 12 months. Planned environmental measurements were not always compatible with day-to-day refuge management actions; this incompatibility highlighted the need for flexible biological monitoring plans. As one of the first field tests of dust suppressants that explicitly incorporated biological endpoints, this effort provides valuable information for improving field tests and for developing laboratory or semifield alternatives.

[Geochemical characteristics and sources of atmospheric particulates in Shanghai during dust storm event].

Science.gov (United States)

Qian, Peng; Zheng, Xiang-min; Zhou, Li-min

2013-05-01

Atmospheric particulates were sampled from three sampling sites of Putuo, Minhang and Qingpu Districts in Shanghai between Oct. , 2009 and Oct. , 2010. In addition, particulate samples were also collected from Nantong, Zhengzhou, Xi'an, and Beijing city where dust storm dust transported along during spring. Element compositions of atmospheric particulates were determined by XRF and ICP-MS. The concentrations of major and trace elements in atmospheric particulates from Putuo, Minhang and Qingpu Districts were similar, indicating their common source. The UCC standardization distribution map showed that the major element composition of dust storm samples was similar to that of loess in northwestern China, indicating that the dust storm dust was mainly derived from Western desert and partly from local area. The REE partition patterns of dust storm dusts among different cities along dust transport route were similar to each other, as well as to those of northern loess, which indicates that the dust storm samples may have the same material source as loess, which mainly comes from crust material. However, the REE partition patterns of non-dust storm particulates were different among the studied cities, and different from those of loess, which suggests that the non-dust storm samples may be mixed with non-crust source material, which is different from dust storm dust and loess. The major element composition and REE partition pattern are effective indicators for source tracing of dust storm dust.

Identification of dust storm source areas in West Asia using multiple environmental datasets.

Science.gov (United States)

Cao, Hui; Amiraslani, Farshad; Liu, Jian; Zhou, Na

2015-01-01

Sand and Dust storms are common phenomena in arid and semi-arid areas. West Asia Region, especially Tigris-Euphrates alluvial plain, has been recognized as one of the most important dust source areas in the world. In this paper, a method is applied to extract SDS (Sand and Dust Storms) sources in West Asia region using thematic maps, climate and geography, HYSPLIT model and satellite images. Out of 50 dust storms happened during 2000-2013 and collected in form of MODIS images, 27 events were incorporated as demonstrations of the simulated trajectories by HYSPLIT model. Besides, a dataset of the newly released Landsat images was used as base-map for the interpretation of SDS source regions. As a result, six main clusters were recognized as dust source areas. Of which, 3 clusters situated in Tigris-Euphrates plain were identified as severe SDS sources (including 70% dust storms in this research). Another cluster in Sistan plain is also a potential source area. This approach also confirmed six main paths causing dust storms. These paths are driven by the climate system including Siberian and Polar anticyclones, monsoon from Indian Subcontinent and depression from north of Africa. The identification of SDS source areas and paths will improve our understandings on the mechanisms and impacts of dust storms on socio-economy and environment of the region. Copyright © 2014 Elsevier B.V. All rights reserved.

FORENSIC CRIMINOLOGY - FUGITIVE PSYCHOLOGY

OpenAIRE

Nyagudi, Nyagudi Musandu

2014-01-01

Forensic Criminology – Fugitive Psychology, 2010 Security Summit (Regional Security Exhibition & Conference ) a forum hosted by Kenya Security Industry Association, Securi Fast Trainers & Consultants, Fidelity Security Limited at Desmond Tutu Conference Centre, Nairobi Kenya from 4th-5th March, 2010  

Quantification of dust generating sources in gold and platinum mines.

CSIR Research Space (South Africa)

Biffi, M

2003-03-01

Full Text Available of workers from harmful respirable dust as well as projections for future work. Summary of dust levels from test mines Dust Levels [mg/m³] Mine Mine Type Dust Source Min Max Avg Crystalline Silica [%] Intake 0.09 1.57 0.46 Tips 0.23 0.65 0... ? The movement of people and rolling stock along haulages, travelling ways and production areas liberating settled dust, ? Rock crushing. ? Screening, grinding, milling and pulverising of the ore during processing. ? Backfill placement. Good practice...

Determination of road dust loadings and chemical characteristics using resuspension.

Science.gov (United States)

Chen, Jianhua; Wang, Wei; Liu, Hongjie; Ren, Lihong

2012-03-01

The contribution of fugitive dust from traffic to air pollution can no longer be ignored in China. In order to obtain the road dust loadings and to understand the chemical characteristics of PM(10) and PM(2.5) from typical road dust, different paved roads in eight districts of Beijing were selected for dust collection during the four seasons of 2005. Ninety-eight samples from 28 roads were obtained. The samples were resuspended using equipment assembled to simulate the rising process of road dust caused by the wind or wheels in order to obtain the PM(10) and PM(2.5) filter samples. The average road dust loading was 3.82 g m(-2), with the highest of 24.22 g m(-2) being in Hutongs in the rural-urban continuum during winter. The road dust loadings on higher-grade roads were lower than those on lower-grade roads. Attention should be paid to the pollution in the rural-urban continuum areas. The sums of element abundances measured were 16.17% and 18.50% for PM(10) and PM(2.5) in road dust. The average abundances of OC and EC in PM(10) and PM(2.5) in road dust were 11.52%, 2.01% and 12.50%, 2.06%, respectively. The abundance of elements, water-soluble ions, and OC, EC in PM(10) and PM(2.5) resuspended from road dust did not change greatly with seasons and road types. The soil dust, construction dust, dust emitted from burning coal, vehicle exhaust, and deposition of particles in the air were the main sources of road dust in Beijing. Affected by the application of snow-melting agents in Beijing during winter, the amount of Cl( - ) and Na( + ) was much higher during that time than in the other seasons. This will have a certain influence on roads, bridges, vegetations, and groundwater.

Center for Corporate Climate Leadership: Direct Fugitive Emissions from Refrigeration, Air Conditioning, Fire Suppression, and Industrial Gases

Science.gov (United States)

This guidance document focuses on several fugitive emissions sources that are common for organizations in many sectors: refrigeration and air conditioningsystems, fire suppression systems, and the purchase and release of industrial gases.

THE DUST BUDGET OF THE SMALL MAGELLANIC CLOUD: ARE ASYMPTOTIC GIANT BRANCH STARS THE PRIMARY DUST SOURCE AT LOW METALLICITY?

International Nuclear Information System (INIS)

Boyer, M. L.; Gordon, K. D.; Meixner, M.; Sargent, B. A.; Srinivasan, S.; Riebel, D.; McDonald, I.; Van Loon, J. Th.; Clayton, G. C.; Sloan, G. C.

2012-01-01

We estimate the total dust input from the cool evolved stars in the Small Magellanic Cloud, using the 8 μm excess emission as a proxy for the dust-production rate (DPR). We find that asymptotic giant branch (AGB) and red supergiant (RSG) stars produce (8.6-9.5) × 10 –7 M ☉ yr –1 of dust, depending on the fraction of far-infrared sources that belong to the evolved star population (with 10%-50% uncertainty in individual DPRs). RSGs contribute the least ( –3 M ☉ of dust each, then the total SN dust input and AGB input are roughly equivalent. We consider several scenarios of SN dust production and destruction and find that the interstellar medium (ISM) dust can be accounted for solely by stellar sources if all SNe produce dust in the quantities seen around the dustiest examples and if most SNe explode in dense regions where much of the ISM dust is shielded from the shocks. We find that AGB stars contribute only 2.1% of the ISM dust. Without a net positive contribution from SNe to the dust budget, this suggests that dust must grow in the ISM or be formed by another unknown mechanism.

Paracas dust storms: Sources, trajectories and associated meteorological conditions

Science.gov (United States)

Briceño-Zuluaga, F.; Castagna, A.; Rutllant, J. A.; Flores-Aqueveque, V.; Caquineau, S.; Sifeddine, A.; Velazco, F.; Gutierrez, D.; Cardich, J.

2017-09-01

Dust storms that develop along the Pisco-Ica desert in Southern Peru, locally known as ;Paracas; winds have ecological, health and economic repercussions. Here we identify dust sources through MODIS (Moderate Resolution Imaging Spectroradiometer) imagery and analyze HYSPLIT (Hybrid Single Particles Lagrangian Integrated Trajectory) model trajectories and dispersion patterns, along with concomitant synoptic-scale meteorological conditions from National Centers for Environmental Prediction/National Center for Atmospheric Research reanalysis (NCEP/NCAR). Additionally, surface pressure data from the hourly METeorological Aerodrome Report (METAR) at Arica (18.5°S, 70.3°W) and Pisco (13.7°S, 76.2°W) were used to calculate Alongshore (sea-level) Pressure Gradient (APG) anomalies during Paracas dust storms, their duration and associated wind-speeds and wind directions. This study provides a review on the occurrence and strength of the Paracas dust storms as reported in the Pisco airfield for five-year period and their correspondence with MODIS true-color imagery in terms of dust-emission source areas. Our results show that most of the particle fluxes moving into the Ica-Pisco desert area during Paracas wind events originate over the coastal zone, where strong winds forced by steep APGs develop as the axis of a deep mid-troposphere trough sets in along north-central Chile. Direct relationships between Paracas wind intensity, number of active dust-emission sources and APGs are also documented, although the scarcity of simultaneous METAR/MODIS data for clearly observed MODIS dust plumes prevents any significant statistical inference. Synoptic-scale meteorological composites from NCEP/NCAR reanalysis data show that Paracas wind events (steep APGs) are mostly associated with the strengthening of anticyclonic conditions in northern Chile, that can be attributed to cold air advection associated with the incoming trough. Compared to the MODIS images, HYSPLIT outputs were able

Assessing fugitive emissions of CH4 from high-pressure gas pipelines

Science.gov (United States)

Worrall, Fred; Boothroyd, Ian; Davies, Richard

2017-04-01

The impact of unconventional natural gas production using hydraulic fracturing methods from shale gas basins has been assessed using life-cycle emissions inventories, covering areas such as pre-production, production and transmission processes. The transmission of natural gas from well pad to processing plants and its transport to domestic sites is an important source of fugitive CH4, yet emissions factors and fluxes from transmission processes are often based upon ver out of date measurements. It is important to determine accurate measurements of natural gas losses when compressed and transported between production and processing facilities so as to accurately determine life-cycle CH4 emissions. This study considers CH4 emissions from the UK National Transmission System (NTS) of high pressure natural gas pipelines. Mobile surveys of CH4 emissions using a Picarro Surveyor cavity-ring-down spectrometer were conducted across four areas in the UK, with routes bisecting high pressure pipelines and separate control routes away from the pipelines. A manual survey of soil gas measurements was also conducted along one of the high pressure pipelines using a tunable diode laser. When wind adjusted 92 km of high pressure pipeline and 72 km of control route were drive over a 10 day period. When wind and distance adjusted CH4 fluxes were significantly greater on routes with a pipeline than those without. The smallest leak detectable was 3% above ambient (1.03 relative concentration) with any leaks below 3% above ambient assumed ambient. The number of leaks detected along the pipelines correlate to the estimated length of pipe joints, inferring that there are constant fugitive CH4 emissions from these joints. When scaled up to the UK's National Transmission System pipeline length of 7600 km gives a fugitive CH4 flux of 4700 ± 2864 kt CH4/yr - this fugitive emission from high pressure pipelines is 0.016% of the annual gas supply.

Methane fugitive emissions quantification using the novel 'plume camera' (spatial correlation) method

Science.gov (United States)

Crosson, E.; Rella, C.

2012-12-01

Fugitive emissions of methane into the atmosphere are a major concern facing the natural gas production industry. Given that the global warming potential of methane is many times greater than that of carbon dioxide, the importance of quantifying methane emissions becomes clear. The rapidly increasing reliance on shale gas (or other unconventional sources) is only intensifying the interest in fugitive methane releases. Natural gas (which is predominantly methane) is an attractive energy source, as it emits 40% less carbon dioxide per Joule of energy generated than coal. However, if just a small percentage of the natural gas consumed is lost due to fugitive emissions during production, processing, or transport, this global warming benefit is lost (Howarth et al. 2012). It is therefore imperative, as production of natural gas increases, that the fugitive emissions of methane are quantified accurately. Traditional direct measurement techniques often involve physical access of the leak itself to quantify the emissions rate, and are generally require painstaking effort to first find the leak and then quantify the emissions rate. With over half a million natural gas producing wells in the U.S. (U.S. Energy Information Administration), not including the associated processing, storage, and transport facilities, and with each facility having hundreds or even thousands of fittings that can potentially leak, the need is clear to develop methodologies that can provide a rapid and accurate assessment of the total emissions rate on a per-well head basis. In this paper we present a novel method for emissions quantification which uses a 'plume camera' with three 'pixels' to quantify emissions using direct measurements of methane concentration in the downwind plume. By analyzing the spatial correlation between the pixels, the spatial extent of the instantaneous plume can be inferred. This information, when combined with the wind speed through the measurement plane, provides a direct

Mobile sensing of point-source fugitive methane emissions using Bayesian inference: the determination of the likelihood function

Science.gov (United States)

Zhou, X.; Albertson, J. D.

2016-12-01

Natural gas is considered as a bridge fuel towards clean energy due to its potential lower greenhouse gas emission comparing with other fossil fuels. Despite numerous efforts, an efficient and cost-effective approach to monitor fugitive methane emissions along the natural gas production-supply chain has not been developed yet. Recently, mobile methane measurement has been introduced which applies a Bayesian approach to probabilistically infer methane emission rates and update estimates recursively when new measurements become available. However, the likelihood function, especially the error term which determines the shape of the estimate uncertainty, is not rigorously defined and evaluated with field data. To address this issue, we performed a series of near-source (using a specialized vehicle mounted with fast response methane analyzers and a GPS unit. Methane concentrations were measured at two different heights along mobile traversals downwind of the sources, and concurrent wind and temperature data are recorded by nearby 3-D sonic anemometers. With known methane release rates, the measurements were used to determine the functional form and the parameterization of the likelihood function in the Bayesian inference scheme under different meteorological conditions.

Chemical characterization of atmospheric particles and source apportionment in the vicinity of a steelmaking industry

International Nuclear Information System (INIS)

Almeida, S.M.; Lage, J.; Fernández, B.; Garcia, S.; Reis, M.A.; Chaves, P.C.

2015-01-01

The objective of this work was to provide a chemical characterization of atmospheric particles collected in the vicinity of a steelmaking industry and to identify the sources that affect PM 10 levels. A total of 94 PM samples were collected in two sampling campaigns that occurred in February and June/July of 2011. PM 2.5 and PM 2.5–10 were analyzed for a total of 22 elements by Instrumental Neutron Activation Analysis and Particle Induced X-ray Emission. The concentrations of water soluble ions in PM 10 were measured by Ion Chromatography and Indophenol-Blue Spectrophotometry. Positive Matrix Factorization receptor model was used to identify sources of particulate matter and to determine their mass contribution to PM 10 . Seven main groups of sources were identified: marine aerosol identified by Na and Cl (22%), steelmaking and sinter plant represented by As, Cr, Cu, Fe, Ni, Mn, Pb, Sb and Zn (11%), sinter plant stack identified by NH 4 + , K and Pb (12%), an unidentified Br source (1.8%), secondary aerosol from coke making and blast furnace (19%), fugitive emissions from the handling of raw material, sinter plant and vehicles dust resuspension identified by Al, Ca, La, Si, Ti and V (14%) and sinter plant and blast furnace associated essentially with Fe and Mn (21%). - Highlights: • Emissions from steelworks are very complex. • The larger steelworks contribution to PM 10 was from blast furnace and sinter plant. • Sinter plant stack emissions contributed for 12% of the PM 10 mass. • Secondary aerosol from coke making and blast furnace contributed for 19% of the PM 10 . • Fugitive dust emissions highly contribute to PM 10 mass

Quantifying Fugitive Methane Emissions from Natural Gas Production with Mobile Technology

Science.gov (United States)

Tsai, T.; Rella, C.; Crosson, E.

2013-12-01

Quantification of fugitive methane (CH4) emissions to determine the environmental impact of natural gas production is challenging with current methods. We present a new mobile method known as the Plume Scanner that can quickly quantify CH4 emissions of point sources. The Plume Scanner is a direct measurement technique which utilizes a mobile Picarro cavity ring-down spectrometer and a gas sampling system based on AirCore technology [1]. As the Plume Scanner vehicle drives through the plume, the air is simultaneously sampled at four different heights, and therefore, the spatial CH4 distribution can be captured (Fig. 1). The flux of the plume is then determined by multiplying the spatial CH4 distribution data with the anemometer measurements. In this way, fugitive emission rates of highly localized sources such as natural gas production pads can be made quickly (~7 min). Verification with controlled CH4 releases demonstrate that under stable atmospheric conditions (Pasquill stability class is C or greater), the Plume Scanner measurements have an error of 2% and a repeatability of 15% [2]. Under unstable atmospheric conditions (Class A or B), the error is 6%, and the repeatability increases to 70% due to the variability of wind conditions. Over two weeks, 275 facilities in the Barnett Shale were surveyed from public roads by sampling the air for elevations in CH4 concentration, and 77% were found leaking. Emissions from 52 sites have been quantified with the Plume Scanner (Fig. 2), and the total emission is 4,900 liters per min (lpm) or 39,000 metric tons/yr CO2e. 1. Karion, A., C. Sweeney, P. Tans, and T. Newberger (2010), AirCore: An innovative atmospheric sampling system, J. Atmos. Oceanic Tech, 27, 1839-1853. 2. F. Pasquill (1961), The estimation of the dispersion of wind borne material, Meterol. Mag., 90(1063), 33-49 Figure 1. Plume Scanner Cartoon Figure 2. Distribution of methane fugitive emissions with error bars associated with the Pasquill stability classes

Comparison of conventional and bio-treated methods as dust suppressants.

Science.gov (United States)

Naeimi, Maryam; Chu, Jian

2017-10-01

Dust is an environmental, geotechnical, health, and economical hazard. Fugitive dust emanating along transportation systems such as roads, railways, and airports especially can have significant impacts on health, safety, material loss, cost of maintenance, and interfere with the facilities. Quantitative studies on the effectiveness of the proper dust palliatives and their environmental impact have been studied with a number of biological and chemical methods. The objective of this study was to establish a method for using the microbial Induced calcium carbonate precipitation (MICP) approach to reduce the percent of mass loss against erosive force of wind regarding to the concentration and characteristics of aggregate used, climate, and traffic amounts. The results of this study showed that the required precipitation for dust control of sand by 70% is less than 15 g CaCO 3 /m 2 between sand grains in bio-treated sand. The wind tunnel test results of this study also indicate that the effectiveness of the bio-treatment method for dust control depends on many variables, such as the percent of precipitated calcium carbonate and tensile strength.

Advances in Mineral Dust Source Composition Measurement with Imaging Spectroscopy at the Salton Sea, CA

Science.gov (United States)

Green, R. O.; Realmuto, V. J.; Thompson, D. R.; Mahowald, N. M.; Pérez García-Pando, C.; Miller, R. L.; Clark, R. N.; Swayze, G. A.; Okin, G. S.

2015-12-01

Mineral dust emitted from the Earth's surface is a principal contributor to direct radiative forcing over the arid regions, where shifts in climate have a significant impact on agriculture, precipitation, and desert encroachment around the globe. Dust particles contribute to both positive and negative forcing, depending on the composition of the particles. Particle composition is a function of the surface mineralogy of dust source regions, but poor knowledge of surface mineralogy on regional to global scales limits the skill of Earth System models to predict shifts in regional climate around the globe. Earth System models include the source, emission, transport and deposition phases of the dust cycle. In addition to direct radiative forcing contributions, mineral dust impacts include indirect radiative forcing, modification of the albedo and melting rates of snow and ice, kinetics of tropospheric photochemistry, formation and deposition of acidic aerosols, supply of nutrients to aquatic and terrestrial ecosystems, and impact on human health and safety. We demonstrate the ability to map mineral dust source composition in the Salton Sea dust source region with imaging spectroscopy measurements acquired as part of the NASA HyspIRI preparatory airborne campaign. These new spectroscopically derived compositional measurements provide a six orders of magnitude improvement over current atlases for this dust source region and provide a pathfinder example for a remote measurement approach to address this critical dust composition gap for global Earth System models.

Integrated spatiotemporal characterization of dust sources and outbreaks in Central and East Asia

Science.gov (United States)

Darmenova, Kremena T.

The potential of atmospheric dust aerosols to modify the Earth's environment and climate has been recognized for some time. However, predicting the diverse impact of dust has several significant challenges. One is to quantify the complex spatial and temporal variability of dust burden in the atmosphere. Another is to quantify the fraction of dust originating from human-made sources. This thesis focuses on the spatiotemporal characterization of sources and dust outbreaks in Central and East Asia by integrating ground-based data, satellite multisensor observations, and modeling. A new regional dust modeling system capable of operating over a span of scales was developed. The modeling system consists of a dust module DuMo, which incorporates several dust emission schemes of different complexity, and the PSU/NCAR mesoscale model MM5, which offers a variety of physical parameterizations and flexible nesting capability. The modeling system was used to perform for the first time a comprehensive study of the timing, duration, and intensity of individual dust events in Central and East Asia. Determining the uncertainties caused by the choice of model physics, especially the boundary layer parameterization, and the dust production scheme was the focus of our study. Implications to assessments of the anthropogenic dust fraction in these regions were also addressed. Focusing on Spring 2001, an analysis of routine surface meteorological observations and satellite multi-sensor data was carried out in conjunction with modeling to determine the extent to which integrated data set can be used to characterize the spatiotemporal distribution of dust plumes at a range of temporal scales, addressing the active dust sources in China and Mongolia, mid-range transport and trans-Pacific, long-range transport of dust outbreaks on a case-by-case basis. This work demonstrates that adequate and consistent characterization of individual dust events is central to establishing a reliable

Development of a life-cycle fugitive methane emissions model utilizing device level emissions and activity factors

Science.gov (United States)

Englander, J.; Brandt, A. R.

2017-12-01

There has been numerous studies in quantifying the scale of fugitive emissions from across the natural gas value chain. These studies have typically focused on either specific types of equipment (such as valves) or on a single part of the life-cycle of natural gas production (such as gathering stations).1,2 However it has been demonstrated that average emissions factors are not sufficient for representing leaks in the natural gas system.3 In this work, we develop a robust estimate of fugitive emissions rates by incorporating all publicly available studies done at the component up to the process level. From these known studies, we create a database of leaks with normalized nomenclature from which leak estimates can be drawn from actual leak observations. From this database, and parameterized by meta-data such as location, scale of study, or placement in the life-cycle, we construct stochastic emissions factors specific for each process unit. This will be an integrated tool as part of the Oil production greenhouse gas estimator (OPGEE) as well as the Fugitive Emissions Abatement Simulation Toolkit (FEAST) models to enhances their treatment of venting and fugitive emissions, and will be flexible to include user provided data and input parameters.4,51. Thoma, ED et al. Assessment of Uinta Basin Oil and Natural Gas Well Pad Pneumatic Controller Emissions. J. Environ. Prot. 2017. 2. Marchese, AJ et al. Methane Emissions from United States Natural Gas Gathering and Processing. ES&T 2015. doi:10.1021/acs.est.5b02275 3. Brandt, AR et al. Methane Leaks from Natural Gas Systems Follow Extreme Distributions. ES&T 2016. doi:10.1021/acs.est.6b04303 4. El-Houjeiri, HM et al. An open-source LCA tool estimating greenhouse gas emissions from crude oil production using field characteristics. ES&T 2013. doi: 10.1021/es304570m 5. Kemp, CE et al. Comparing Natural Gas Leakage Detection Technologies Using an Open-Source `Virtual Gas Field' Simulator. ES&T 2016. doi:10.1021/acs.est.5b

Natural gas fugitive emissions rates constrained by global atmospheric methane and ethane.

Science.gov (United States)

Schwietzke, Stefan; Griffin, W Michael; Matthews, H Scott; Bruhwiler, Lori M P

2014-07-15

The amount of methane emissions released by the natural gas (NG) industry is a critical and uncertain value for various industry and policy decisions, such as for determining the climate implications of using NG over coal. Previous studies have estimated fugitive emissions rates (FER)--the fraction of produced NG (mainly methane and ethane) escaped to the atmosphere--between 1 and 9%. Most of these studies rely on few and outdated measurements, and some may represent only temporal/regional NG industry snapshots. This study estimates NG industry representative FER using global atmospheric methane and ethane measurements over three decades, and literature ranges of (i) tracer gas atmospheric lifetimes, (ii) non-NG source estimates, and (iii) fossil fuel fugitive gas hydrocarbon compositions. The modeling suggests an upper bound global average FER of 5% during 2006-2011, and a most likely FER of 2-4% since 2000, trending downward. These results do not account for highly uncertain natural hydrocarbon seepage, which could lower the FER. Further emissions reductions by the NG industry may be needed to ensure climate benefits over coal during the next few decades.

Directional Unfolded Source Term (DUST) for Compton Cameras.

Energy Technology Data Exchange (ETDEWEB)

Mitchell, Dean J.; Mitchell, Dean J.; Horne, Steven M.; O' Brien, Sean; Thoreson, Gregory G

2018-03-01

A Directional Unfolded Source Term (DUST) algorithm was developed to enable improved spectral analysis capabilities using data collected by Compton cameras. Achieving this objective required modification of the detector response function in the Gamma Detector Response and Analysis Software (GADRAS). Experimental data that were collected in support of this work include measurements of calibration sources at a range of separation distances and cylindrical depleted uranium castings.

Dust Storm over the Middle East: Retrieval Approach, Source Identification, and Trend Analysis

Science.gov (United States)

Moridnejad, A.; Karimi, N.; Ariya, P. A.

2014-12-01

The Middle East region has been considered to be responsible for approximately 25% of the Earth's global emissions of dust particles. By developing Middle East Dust Index (MEDI) and applying to 70 dust storms characterized on MODIS images and occurred during the period between 2001 and 2012, we herein present a new high resolution mapping of major atmospheric dust source points participating in this region. To assist environmental managers and decision maker in taking proper and prioritized measures, we then categorize identified sources in terms of intensity based on extracted indices for Deep Blue algorithm and also utilize frequency of occurrence approach to find the sensitive sources. In next step, by implementing the spectral mixture analysis on the Landsat TM images (1984 and 2012), a novel desertification map will be presented. The aim is to understand how human perturbations and land-use change have influenced the dust storm points in the region. Preliminary results of this study indicate for the first time that c.a., 39 % of all detected source points are located in this newly anthropogenically desertified area. A large number of low frequency sources are located within or close to the newly desertified areas. These severely desertified regions require immediate concern at a global scale. During next 6 months, further research will be performed to confirm these preliminary results.

Assessing fugitive emissions of CH4 from high-pressure gas pipelines in the UK

Science.gov (United States)

Clancy, S.; Worrall, F.; Davies, R. J.; Almond, S.; Boothroyd, I.

2016-12-01

Concern over the greenhouse gas impact of the exploitation of unconventional natural gas from shale deposits has caused a spotlight to be shone on to the entire hydrocarbon industry. Numerous studies have developed life-cycle emissions inventories to assess the impact that hydraulic fracturing has upon greenhouse gas emissions. Incorporated within life-cycle assessments are transmission and distribution losses, including infrastructure such as pipelines and compressor stations that pressurise natural gas for transport along pipelines. Estimates of fugitive emissions from transmission, storage and distribution have been criticized for reliance on old data from inappropriate sources (1970s Russian gas pipelines). In this study, we investigate fugitive emissions of CH4 from the UK high pressure national transmission system. The study took two approaches. Firstly, CH4 concentration is detected by driving along roads bisecting high pressure gas pipelines and also along an equivalent distance along a route where no high pressure gas pipeline was nearby. Five pipelines and five equivalent control routes were driven and the test was that CH4 measurements, when adjusted for distance and wind speed, should be greater on any route with a pipe than any route without a pipe. Secondly, 5 km of a high pressure gas pipeline and 5 km of equivalent farmland, were walked and soil gas (above the pipeline where present) was analysed every 7 m using a tunable diode laser. When wind adjusted 92 km of high pressure pipeline and 72 km of control route were drive over a 10 day period. When wind and distance adjusted CH4 fluxes were significantly greater on routes with a pipeline than those without. The smallest leak detectable was 3% above ambient (1.03 relative concentration) with any leaks below 3% above ambient assumed ambient. The number of leaks detected along the pipelines correlate to the estimated length of pipe joints, inferring that there are constant fugitive CH4 emissions from

Road dust and its effect on human health: a literature review

Science.gov (United States)

2018-01-01

The purpose of this study was to determine the effects of road dust on human health. A PubMed search was used to extract references that included the words “road dust” and “health” or “fugitive dust” and “health” in the title or abstract. A total of 46 references were extracted and selected for review after the primary screening of 949 articles. The respiratory system was found to be the most affected system in the human body. Lead, platinum-group elements (platinum, rhodium, and bohrium), aluminum, zinc, vanadium, and polycyclic aromatic hydrocarbons were the components of road dust that were most frequently referenced in the articles reviewed. Road dust was found to have harmful effects on the human body, especially on the respiratory system. To determine the complex mechanism of action of various components of road dust on the human body and the results thereof, the authors recommend a further meta-analysis and extensive risk-assessment research into the health impacts of dust exposure. PMID:29642653

On supernovae as a source of interstellar dust. The current observational picture

International Nuclear Information System (INIS)

Dinerstein, H.L.

1984-01-01

Supernovae have been generally thought of as being effective agents for the destruction of ambient interstellar dust. The idea that supernovae may also be a source of dust has been of interest recently, and is attractive for a couple of reasons. The main motivation is to explain meteoritic inclusions with peculiar isotopic abundance ratios as supernova dust condensates predating the solar nebula. In addition, although the nucleation process is not fully understood, the high concentration of condensable elements in the supernova mantle suggests the possibility that grain formation could be very efficient. In this case, supernovae could be a major source of new grain cores to the interstellar medium. (author)

Source apportionment of fine particles and its chemical components over the Yangtze River Delta, China during a heavy haze pollution episode

Science.gov (United States)

Li, L.; An, J. Y.; Zhou, M.; Yan, R. S.; Huang, C.; Lu, Q.; Lin, L.; Wang, Y. J.; Tao, S. K.; Qiao, L. P.; Zhu, S. H.; Chen, C. H.

2015-12-01

An extremely high PM2.5 pollution episode occurred over the eastern China in January 2013. In this paper, the particulate matter source apportionment technology (PSAT) method coupled within the Comprehensive air quality model with extensions (CAMx) is applied to study the source contributions to PM2.5 and its major components at six receptors (Urban Shanghai, Chongming, Dianshan Lake, Urban Suzhou, Hangzhou and Zhoushan) in the Yangtze River Delta (YRD) region. Contributions from 4 source areas (including Shanghai, South Jiangsu, North Zhejiang and Super-region) and 9 emission sectors (including power plants, industrial boilers and kilns, industrial processing, mobile source, residential, volatile emissions, dust, agriculture and biogenic emissions) to PM2.5 and its major components (sulfate, nitrate, ammonia, organic carbon and elemental carbon) at the six receptors in the YRD region are quantified. Results show that accumulation of local pollution was the largest contributor during this air pollution episode in urban Shanghai (55%) and Suzhou (46%), followed by long-range transport (37% contribution to Shanghai and 44% to Suzhou). Super-regional emissions play an important role in PM2.5 formation at Hangzhou (48%) and Zhoushan site (68%). Among the emission sectors contributing to the high pollution episode, the major source categories include industrial processing (with contributions ranging between 12.7 and 38.7% at different receptors), combustion source (21.7-37.3%), mobile source (7.5-17.7%) and fugitive dust (8.4-27.3%). Agricultural contribution is also very significant at Zhoushan site (24.5%). In terms of the PM2.5 major components, it is found that industrial boilers and kilns are the major source contributor to sulfate and nitrate. Volatile emission source and agriculture are the major contributors to ammonia; transport is the largest contributor to elemental carbon. Industrial processing, volatile emissions and mobile source are the most significant

Chemical characterization of atmospheric particles and source apportionment in the vicinity of a steelmaking industry

Energy Technology Data Exchange (ETDEWEB)

Almeida, S.M., E-mail: smarta@ctn.ist.utl.pt [Centro de Ciências e Tecnologias Nucleares, Instituto Superior Técnico, Universidade de Lisboa, Estrada Nacional 10, 139.7 km, 2695-066 Bobadela LRS (Portugal); Lage, J. [Centro de Ciências e Tecnologias Nucleares, Instituto Superior Técnico, Universidade de Lisboa, Estrada Nacional 10, 139.7 km, 2695-066 Bobadela LRS (Portugal); Fernández, B. [Global R& D, ArcelorMittal, Avilés (Spain); Garcia, S. [Instituto de Soldadura e Qualidade, Av. Prof. Dr. Cavaco Silva, 33, 2740-120 Porto Salvo (Portugal); Reis, M.A.; Chaves, P.C. [Centro de Ciências e Tecnologias Nucleares, Instituto Superior Técnico, Universidade de Lisboa, Estrada Nacional 10, 139.7 km, 2695-066 Bobadela LRS (Portugal)

2015-07-15

The objective of this work was to provide a chemical characterization of atmospheric particles collected in the vicinity of a steelmaking industry and to identify the sources that affect PM{sub 10} levels. A total of 94 PM samples were collected in two sampling campaigns that occurred in February and June/July of 2011. PM{sub 2.5} and PM{sub 2.5–10} were analyzed for a total of 22 elements by Instrumental Neutron Activation Analysis and Particle Induced X-ray Emission. The concentrations of water soluble ions in PM{sub 10} were measured by Ion Chromatography and Indophenol-Blue Spectrophotometry. Positive Matrix Factorization receptor model was used to identify sources of particulate matter and to determine their mass contribution to PM{sub 10}. Seven main groups of sources were identified: marine aerosol identified by Na and Cl (22%), steelmaking and sinter plant represented by As, Cr, Cu, Fe, Ni, Mn, Pb, Sb and Zn (11%), sinter plant stack identified by NH{sub 4}{sup +}, K and Pb (12%), an unidentified Br source (1.8%), secondary aerosol from coke making and blast furnace (19%), fugitive emissions from the handling of raw material, sinter plant and vehicles dust resuspension identified by Al, Ca, La, Si, Ti and V (14%) and sinter plant and blast furnace associated essentially with Fe and Mn (21%). - Highlights: • Emissions from steelworks are very complex. • The larger steelworks contribution to PM{sub 10} was from blast furnace and sinter plant. • Sinter plant stack emissions contributed for 12% of the PM{sub 10} mass. • Secondary aerosol from coke making and blast furnace contributed for 19% of the PM{sub 10}. • Fugitive dust emissions highly contribute to PM{sub 10} mass.

Applying geochemical signatures of atmospheric dust to distinguish current mine emissions from legacy sources

Science.gov (United States)

Dong, Chenyin; Taylor, Mark Patrick

2017-07-01

Resolving the source of environmental contamination is the critical first step in remediation and exposure prevention. Australia's oldest silver-zinc-lead mine at Broken Hill (>130 years old) has generated a legacy of contamination and is associated with persistent elevated childhood blood lead (Pb) levels. However, the source of environmental Pb remains in dispute: current mine emissions; remobilized mine-legacy lead in soils and dusts; and natural lead from geological weathering of the gossan ore body. Multiple lines of evidence used to resolve this conundrum at Broken Hill include spatial and temporal variations in dust Pb concentrations and bioaccessibility, Pb isotopic compositions, particle morphology and mineralogy. Total dust Pb loading (mean 255 μg/m2/day) and its bioaccessibility (mean 75% of total Pb) is greatest adjacent to the active mining operations. Unweathered galena (PbS) found in contemporary dust deposits contrast markedly to Pb-bearing particles from mine-tailings and weathered gossan samples. Contemporary dust particles were more angular, had higher sulfur content and had little or no iron and manganese. Dust adjacent to the mine has Pb isotopic compositions (208Pb/207Pb: 2.3197; 206Pb/207Pb: 1.0406) that are a close match (99%) to the ore body with values slightly lower (94%) at the edge of the city. The weight of evidence supports the conclusion that contemporary dust Pb contamination in Broken Hill is sourced primarily from current mining activities and not from weathering or legacy sources.

Source diagnostics of polycyclic aromatic hydrocarbons in urban road runoff, dust, rain and canopy throughfall

International Nuclear Information System (INIS)

Zhang Wei; Zhang Shucai; Wan Chao; Yue Dapan; Ye Youbin; Wang Xuejun

2008-01-01

Diagnostic ratios and multivariate analysis were utilized to apportion polycyclic aromatic hydrocarbon (PAH) sources for road runoff, road dust, rain and canopy throughfall based on samples collected in an urban area of Beijing, China. Three sampling sites representing vehicle lane, bicycle lane and branch road were selected. For road runoff and road dust, vehicular emission and coal combustion were identified as major sources, and the source contributions varied among the sampling sites. For rain, three principal components were apportioned representing coal/oil combustion (54%), vehicular emission (34%) and coking (12%). For canopy throughfall, vehicular emission (56%), coal combustion (30%) and oil combustion (14%) were identified as major sources. Overall, the PAH's source for road runoff mainly reflected that for road dust. Despite site-specific sources, the findings at the study area provided a general picture of PAHs sources for the road runoff system in urban area of Beijing. - Urban road runoff and road dust, canopy throughfall and rain were considered as a system for diagnostics of PAH sources

PM10 standards and nontraditional particulate source controls: Research perspective

International Nuclear Information System (INIS)

Watson, J.G.

1992-01-01

Knowledge of how to measure suspended particles, what their concentrations are, what they are composed of, and where they come from has increased substantially since 1975. At that time, much of the pioneering work in these areas was just being conducted and published. Size-classified measurements, low-level elemental analysis, inorganic ion analysis, and carbon determinations for aerosol samples were novel research developments. Receptor modeling was not considered to be a scientific discipline, let alone a useful tool for source apportionment. Presentations at earlier conferences went to great lengths to document and justify methodologies which are taken for granted at this conference. This paper goes on to discuss research findings in control of wood smoke, fugitive dusts, motor vehicle exhausts, and secondary aerosols. Research results in source apportionment are also discussed

Distribution, sources and health risk assessment of mercury in kindergarten dust

Science.gov (United States)

Sun, Guangyi; Li, Zhonggen; Bi, Xiangyang; Chen, Yupeng; Lu, Shuangfang; Yuan, Xin

2013-07-01

Mercury (Hg) contamination in urban area is a hot issue in environmental research. In this study, the distribution, sources and health risk of Hg in dust from 69 kindergartens in Wuhan, China, were investigated. In comparison with most other cities, the concentrations of total mercury (THg) and methylmercury (MeHg) were significantly elevated, ranging from 0.15 to 10.59 mg kg-1 and from 0.64 to 3.88 μg kg-1, respectively. Among the five different urban areas, the educational area had the highest concentrations of THg and MeHg. The GIS mapping was used to identify the hot-spot areas and assess the potential pollution sources of Hg. The emissions of coal-power plants and coking plants were the main sources of THg in the dust, whereas the contributions of municipal solid waste (MSW) landfills and iron and steel smelting related industries were not significant. However, the emission of MSW landfills was considered to be an important source of MeHg in the studied area. The result of health risk assessment indicated that there was a high adverse health effect of the kindergarten dust in terms of Hg contamination on the children living in the educational area (Hazard index (HI) = 6.89).

Diffuse and fugitive emission dose assessment on the Hanford Site

International Nuclear Information System (INIS)

Davis, W.E.; Schmidt, J.W.; Gleckler, B.P.; Rhoads, K.

1995-01-01

On February 3, 1993, the US Department of Energy, Richland Operations Office (RL), received a Compliance Order and Information Request from the Director of the Air and Toxics Division of the US Environmental Protection Agency (EPA), Region 10. The Compliance Order requires RL to (1) evaluate all radionuclide emission points at the Hanford Site to determine which are subject to continuous emission measurement requirements in 40 Code of Federal Regulations (CFR) 61, Subpart H, and (2) continuously measure radionuclide emissions in accordance with 40 CFR 61.93. The Information Request requires RL to provide a written Compliance Plan to meet the requirements of the Compliance Order. The RL Compliance Plan included as one of its milestones the requirement to develop a Federal Facility Compliance Agreement (FFCA). An FFCA was negotiated between RL and the EPA, Region 10, and was entered into on February 7, 1994. One of the milestones was to provide EPA, Region 10, with a copy of the Federal Clean Air Act Title V operating air permit application and Air Emission Inventory (AEI) concurrent with its submission to the Washington State Department of Ecology. The AEI will include an assessment of the diffuse and fugitive emissions from the Hanford Site. This assessment does not identify any diffuse or fugitive emission source that would cause an effective dose equivalent greater than 0.1 mrem/yr

Optical and microphysical properties of natural mineral dust and anthropogenic soil dust near dust source regions over northwestern China

Science.gov (United States)

Wang, Xin; Wen, Hui; Shi, Jinsen; Bi, Jianrong; Huang, Zhongwei; Zhang, Beidou; Zhou, Tian; Fu, Kaiqi; Chen, Quanliang; Xin, Jinyuan

2018-02-01

Mineral dust aerosols (MDs) not only influence the climate by scattering and absorbing solar radiation but also modify cloud properties and change the ecosystem. From 3 April to 16 May 2014, a ground-based mobile laboratory was deployed to measure the optical and microphysical properties of MDs near dust source regions in Wuwei, Zhangye, and Dunhuang (in chronological order) along the Hexi Corridor over northwestern China. Throughout this dust campaign, the hourly averaged (±standard deviation) aerosol scattering coefficients (σsp, 550 nm) of the particulates with aerodynamic diameters less than 2.5 µm (PM2.5) at these three sites were sequentially 101.5 ± 36.8, 182.2 ± 433.1, and 54.0 ± 32.0 Mm-1. Correspondingly, the absorption coefficients (σap, 637 nm) were 9.7 ± 6.1, 6.0 ± 4.6, and 2.3 ± 0.9 Mm-1; single-scattering albedos (ω, 637 nm) were 0.902 ± 0.025, 0.931 ± 0.037, and 0.949 ± 0.020; and scattering Ångström exponents (Åsp, 450-700 nm) of PM2.5 were 1.28 ± 0.27, 0.77 ± 0.51, and 0.52 ± 0.31. During a severe dust storm in Zhangye (i.e., from 23 to 25 April), the highest values of σsp2.5 ( ˜ 5074 Mm-1), backscattering coefficient (σbsp2.5, ˜ 522 Mm-1), and ω637 ( ˜ 0.993) and the lowest values of backscattering fraction (b2.5, ˜ 0.101) at 550 nm and Åsp2.5 ( ˜ -0.046) at 450-700 nm, with peak values of aerosol number size distribution (appearing at the particle diameter range of 1-3 µm), exhibited that the atmospheric aerosols were dominated by coarse-mode dust aerosols. It is hypothesized that the relatively higher values of mass scattering efficiency during floating dust episodes in Wuwei and Zhangye are attributed to the anthropogenic soil dust produced by agricultural cultivations.

A Mobile Sensing Approach for Regional Surveillance of Fugitive Methane Emissions in Oil and Gas Production.

Science.gov (United States)

Albertson, John D; Harvey, Tierney; Foderaro, Greg; Zhu, Pingping; Zhou, Xiaochi; Ferrari, Silvia; Amin, M Shahrooz; Modrak, Mark; Brantley, Halley; Thoma, Eben D

2016-03-01

This paper addresses the need for surveillance of fugitive methane emissions over broad geographical regions. Most existing techniques suffer from being either extensive (but qualitative) or quantitative (but intensive with poor scalability). A total of two novel advancements are made here. First, a recursive Bayesian method is presented for probabilistically characterizing fugitive point-sources from mobile sensor data. This approach is made possible by a new cross-plume integrated dispersion formulation that overcomes much of the need for time-averaging concentration data. The method is tested here against a limited data set of controlled methane release and shown to perform well. We then present an information-theoretic approach to plan the paths of the sensor-equipped vehicle, where the path is chosen so as to maximize expected reduction in integrated target source rate uncertainty in the region, subject to given starting and ending positions and prevailing meteorological conditions. The information-driven sensor path planning algorithm is tested and shown to provide robust results across a wide range of conditions. An overall system concept is presented for optionally piggybacking of these techniques onto normal industry maintenance operations using sensor-equipped work trucks.

Composition and source apportionment of dust fall around a natural lake.

Science.gov (United States)

Latif, Mohd Talib; Ngah, Sofia Aida; Dominick, Doreena; Razak, Intan Suraya; Guo, Xinxin; Srithawirat, Thunwadee; Mushrifah, Idris

2015-07-01

The aim of this study was to determine the source apportionment of dust fall around Lake Chini, Malaysia. Samples were collected monthly between December 2012 and March 2013 at seven sampling stations located around Lake Chini. The samples were filtered to separate the dissolved and undissolved solids. The ionic compositions (NO3-, SO4(2-), Cl- and NH4+) were determined using ion chromatography (IC) while major elements (K, Na, Ca and Mg) and trace metals (Zn, Fe, Al, Ni, Mn, Cr, Pb and Cd) were determined using inductively coupled plasma mass spectrometry (ICP-MS). The results showed that the average concentration of total solids around Lake Chini was 93.49±16.16 mg/(m2·day). SO4(2-), Na and Zn dominated the dissolved portion of the dust fall. The enrichment factors (EF) revealed that the source of the trace metals and major elements in the rain water was anthropogenic, except for Fe. Hierarchical agglomerative cluster analysis (HACA) classified the seven monitoring stations and 16 variables into five groups and three groups respectively. A coupled receptor model, principal component analysis multiple linear regression (PCA-MLR), revealed that the sources of dust fall in Lake Chini were dominated by agricultural and biomass burning (42%), followed by the earth's crust (28%), sea spray (16%) and a mixture of soil dust and vehicle emissions (14%). Copyright © 2015. Published by Elsevier B.V.

Mechanical resuspension of 239Pu from unpaved roads

International Nuclear Information System (INIS)

Hodgin, C.R.

1982-01-01

The impacts of resuspended plutonium from two unpaved roads at the Rocky Flats Plant on nearby air samplers were investigated. Because the sources were complex fugitive dust emitters and because of the small source-receptor distances, traditional dispersion modeling techniques could not be employed. Thus two specialized techniques, one for fugitive dust emissions and one for near distance dispersion, were developed and used to calculate atmospheric dust concentrations at the subject air samplers. Atmospheric 239 Pu impacts were then determined from measurements of plutonium concentrations in the resuspendible dust on the road surfaces. As a final step in the process the calculated plutonium impacts were compared to the 1980 annual average 239 Pu concentration at four samplers. The impact calculated for the Gunnery Range Road represented 2.1 percent of the observed annual concentration, with a 95 percent confidence interval of 1.1 to 7.9 percent. The Southeast Perimeter Road produced a more substantial effect with a point estimate of 3.8 percent. The 95 percent confidence interval for this source was 2.0 to 9.1 percent. The combined impact of the two roads on the subject samplers was 5.9 percent of the observed plutonium concentration, with a 95 percent confidence interval of 3.2 to 17.0 percent. Thus it was shown that fugitive plutonium emissions from the Gunnery Range Road and Southeast Perimeter Road are not substantial contributors to the plutonium concentrations observed at the subject samplers. Even an increase in dust control efficiency to 90 percent (as with paving) would result in only a four percent decrease in the overall atmosperic plutonium concentration at the site

Coal fly ash as a source of iron in atmospheric dust.

Science.gov (United States)

Chen, Haihan; Laskin, Alexander; Baltrusaitis, Jonas; Gorski, Christopher A; Scherer, Michelle M; Grassian, Vicki H

2012-02-21

Anthropogenic coal fly ash (FA) aerosol may represent a significant source of bioavailable iron in the open ocean. Few measurements have been made that compare the solubility of atmospheric iron from anthropogenic aerosols and other sources. We report here an investigation of iron dissolution for three FA samples in acidic aqueous solutions and compare the solubilities with that of Arizona test dust (AZTD), a reference material for mineral dust. The effects of pH, simulated cloud processing, and solar radiation on iron solubility have been explored. Similar to previously reported results on mineral dust, iron in aluminosilicate phases provides the predominant component of dissolved iron. Iron solubility of FA is substantially higher than of the crystalline minerals comprising AZTD. Simulated atmospheric processing elevates iron solubility due to significant changes in the morphology of aluminosilicate glass, a dominant material in FA particles. Iron is continuously released into the aqueous solution as FA particles break up into smaller fragments. These results suggest that the assessment of dissolved atmospheric iron deposition fluxes and their effect on the biogeochemistry at the ocean surface should be constrained by the source, environmental pH, iron speciation, and solar radiation.

Source diagnostics of polycyclic aromatic hydrocarbons in urban road runoff, dust, rain and canopy throughfall.

Science.gov (United States)

Zhang, Wei; Zhang, Shucai; Wan, Chao; Yue, Dapan; Ye, Youbin; Wang, Xuejun

2008-06-01

Diagnostic ratios and multivariate analysis were utilized to apportion polycyclic aromatic hydrocarbon (PAH) sources for road runoff, road dust, rain and canopy throughfall based on samples collected in an urban area of Beijing, China. Three sampling sites representing vehicle lane, bicycle lane and branch road were selected. For road runoff and road dust, vehicular emission and coal combustion were identified as major sources, and the source contributions varied among the sampling sites. For rain, three principal components were apportioned representing coal/oil combustion (54%), vehicular emission (34%) and coking (12%). For canopy throughfall, vehicular emission (56%), coal combustion (30%) and oil combustion (14%) were identified as major sources. Overall, the PAH's source for road runoff mainly reflected that for road dust. Despite site-specific sources, the findings at the study area provided a general picture of PAHs sources for the road runoff system in urban area of Beijing.

Road fugitive dust emission characteristics in Beijing during Olympics Game 2008 in Beijing, China

Science.gov (United States)

Shou-bin, Fan; Gang, Tian; Gang, Li; Yu-hu, Huang; Jian-ping, Qin; Shui-yuan, Cheng

2009-12-01

Eighty road dust-fall (DF) monitoring sites and 14 background monitoring sites were established in the Beijing metropolitan area, and monitoring was conducted from January 2006 to December 2008. The dust-fall attributable to roads (ΔDF) showed a clear decline from 2006 to 2008. Dust-fall levels decreased across different road types from freeway > major arterial roads > minor arterial roads > collector roads > background sites. The ΔDF showed declines of 65%, 55%, 65% and 84% respectively for freeways, major arterial, minor arterial and collector roads from August 2007 to August 2008, and declines of 77%, 76%, 82% and 82% between August 2006 and August 2008. The ΔDF declined by 80%, 79%, 82% and 69% for freeways, major arterial, minor arterial and collector roads respectively between September 2007 and September 2008, and declined by 84%, 88%, 80% and 81% between September 2006 and September 2008. Eighty samples were collected in August 2007 and August 2008 and analyzed for silt loading. PM 10 emission factors and emission strengths were calculated using the AP-42 model. The silt loading reduced by 77%, 35%, 61%, 59% and 75% for freeways, major arterial, minor arterial, collector and local roads respectively. The PM 10 emission factors were reduced by 57%, 15%, 36%, 51% and 61% and the PM 10 emission strength declined by 70%, 40%, 55%, 65% and 72% for freeways, major arterial, minor arterial, collector and local roads respectively between August 2007 and August 2008. The decline is consistent with the reduction in road dust-fall.

Global Scale Attribution of Anthropogenic and Natural Dust Sources and their Emission Rates Based on MODIS Deep Blue Aerosol Products

Science.gov (United States)

Ginoux, Paul; Prospero, Joseph M.; Gill, Thomas E.; Hsu, N. Christina; Zhao, Ming

2012-01-01

Our understanding of the global dust cycle is limited by a dearth of information about dust sources, especially small-scale features which could account for a large fraction of global emissions. Here we present a global-scale high-resolution (0.1 deg) mapping of sources based on Moderate Resolution Imaging Spectroradiometer (MODIS) Deep Blue estimates of dust optical depth in conjunction with other data sets including land use. We ascribe dust sources to natural and anthropogenic (primarily agricultural) origins, calculate their respective contributions to emissions, and extensively compare these products against literature. Natural dust sources globally account for 75% of emissions; anthropogenic sources account for 25%. North Africa accounts for 55% of global dust emissions with only 8% being anthropogenic, mostly from the Sahel. Elsewhere, anthropogenic dust emissions can be much higher (75% in Australia). Hydrologic dust sources (e.g., ephemeral water bodies) account for 31% worldwide; 15% of them are natural while 85% are anthropogenic. Globally, 20% of emissions are from vegetated surfaces, primarily desert shrublands and agricultural lands. Since anthropogenic dust sources are associated with land use and ephemeral water bodies, both in turn linked to the hydrological cycle, their emissions are affected by climate variability. Such changes in dust emissions can impact climate, air quality, and human health. Improved dust emission estimates will require a better mapping of threshold wind velocities, vegetation dynamics, and surface conditions (soil moisture and land use) especially in the sensitive regions identified here, as well as improved ability to address small-scale convective processes producing dust via cold pool (haboob) events frequent in monsoon regimes.

Global-scale attribution of anthropogenic and natural dust sources and their emission rates based on MODIS Deep Blue aerosol products

Science.gov (United States)

Ginoux, Paul; Prospero, Joseph M.; Gill, Thomas E.; Hsu, N. Christina; Zhao, Ming

2012-09-01

Our understanding of the global dust cycle is limited by a dearth of information about dust sources, especially small-scale features which could account for a large fraction of global emissions. Here we present a global-scale high-resolution (0.1°) mapping of sources based on Moderate Resolution Imaging Spectroradiometer (MODIS) Deep Blue estimates of dust optical depth in conjunction with other data sets including land use. We ascribe dust sources to natural and anthropogenic (primarily agricultural) origins, calculate their respective contributions to emissions, and extensively compare these products against literature. Natural dust sources globally account for 75% of emissions; anthropogenic sources account for 25%. North Africa accounts for 55% of global dust emissions with only 8% being anthropogenic, mostly from the Sahel. Elsewhere, anthropogenic dust emissions can be much higher (75% in Australia). Hydrologic dust sources (e.g., ephemeral water bodies) account for 31% worldwide; 15% of them are natural while 85% are anthropogenic. Globally, 20% of emissions are from vegetated surfaces, primarily desert shrublands and agricultural lands. Since anthropogenic dust sources are associated with land use and ephemeral water bodies, both in turn linked to the hydrological cycle, their emissions are affected by climate variability. Such changes in dust emissions can impact climate, air quality, and human health. Improved dust emission estimates will require a better mapping of threshold wind velocities, vegetation dynamics, and surface conditions (soil moisture and land use) especially in the sensitive regions identified here, as well as improved ability to address small-scale convective processes producing dust via cold pool (haboob) events frequent in monsoon regimes.

Geomorphic and land cover identification of dust sources in the eastern Great Basin of Utah, U.S.A.

Science.gov (United States)

Hahnenberger, Maura; Nicoll, Kathleen

2014-01-01

This study identifies anthropogenically disturbed areas and barren playa surfaces as the two primary dust source types that repeatedly contribute to dust storm events in the eastern Great Basin of western Utah, U.S.A. This semi-arid desert region is an important contributor to dust production in North America, with this study being the first to specifically identify and characterize regional dust sources. From 2004 to 2010, a total of 51 dust event days (DEDs) affected the air quality in Salt Lake City, UT. MODIS satellite imagery during 16 of these DEDs was analyzed to identify dust plumes, and assess the characteristics of dust source areas. A total of 168 plumes were identified, and showed mobilization of dust from Quaternary deposits located within the Bonneville Basin. This analysis identifies 4 major and 5 secondary source areas for dust in this region, which produce dust primarily during the spring and fall months and during moderate or greater drought conditions, with a Palmer Drought Index (PDI) of - 2 or less. The largest number of observed dust plumes (~ 60% of all plumes) originated from playas (ephemeral lakes) and are classified as barren land cover with a silty clay soil sediment surface. Playa surfaces in this region undergo numerous recurrent anthropogenic disturbances, including military operations and anthropogenic water withdrawal. Anthropogenic disturbance is necessary to produce dust from the vegetated landscape in the eastern Great Basin, as evidenced by the new dust source active from 2008 to 2010 in the area burned by the 2007 Milford Flat Fire; this fire was the largest in Utah's history due to extensive cover of invasive cheatgrass (Bromus tectorum) along with drought conditions. However, dust mobilization from the Milford Flat Burned Area was limited to regions that had been significantly disturbed by post-fire land management techniques that consisted of seeding, followed by chaining or tilling of the soil. Dust storms in the eastern

Refinery evaluation of optical imaging to locate fugitive emissions.

Science.gov (United States)

Robinson, Donald R; Luke-Boone, Ronke; Aggarwal, Vineet; Harris, Buzz; Anderson, Eric; Ranum, David; Kulp, Thomas J; Armstrong, Karla; Sommers, Ricky; McRae, Thomas G; Ritter, Karin; Siegell, Jeffrey H; Van Pelt, Doug; Smylie, Mike

2007-07-01

Fugitive emissions account for approximately 50% of total hydrocarbon emissions from process plants. Federal and state regulations aiming at controlling these emissions require refineries and petrochemical plants in the United States to implement a Leak Detection and Repair Program (LDAR). The current regulatory work practice, U.S. Environment Protection Agency Method 21, requires designated components to be monitored individually at regular intervals. The annual costs of these LDAR programs in a typical refinery can exceed US$1,000,000. Previous studies have shown that a majority of controllable fugitive emissions come from a very small fraction of components. The Smart LDAR program aims to find cost-effective methods to monitor and reduce emissions from these large leakers. Optical gas imaging has been identified as one such technology that can help achieve this objective. This paper discusses a refinery evaluation of an instrument based on backscatter absorption gas imaging technology. This portable camera allows an operator to scan components more quickly and image gas leaks in real time. During the evaluation, the instrument was able to identify leaking components that were the source of 97% of the total mass emissions from leaks detected. More than 27,000 components were monitored. This was achieved in far less time than it would have taken using Method 21. In addition, the instrument was able to find leaks from components that are not required to be monitored by the current LDAR regulations. The technology principles and the parameters that affect instrument performance are also discussed in the paper.

Iron Oxide Minerals in Atmospheric Dust and Source Sediments-Studies of Types and Properties to Assess Environmental Effects

Science.gov (United States)

Reynolds, R. L.; Goldstein, H. L.; Moskowitz, B. M.; Till, J. L.; Flagg, C.; Kokaly, R. F.; Munson, S.; Landry, C.; Lawrence, C. R.; Hiza, M. M.; D'Odorico, P.; Painter, T. H.

2011-12-01

Ferric oxide minerals in atmospheric dust can influence atmospheric temperatures, accelerate melting of snow and ice, stimulate marine phytoplankton productivity, and impact human health. Such effects vary depending on iron mineral type, size, surface area, and solubility. Generally, the presence of ferric oxides in dust is seen in the red, orange, or yellow hues of plumes that originate in North Africa, central and southwest Asia, South America, western North America, and Australia. Despite their global importance, these minerals in source sediments, atmospheric dust, and downwind aeolian deposits remain poorly described with respect to specific mineralogy, particle size and surface area, or presence in far-traveled aerosol compounds. The types and properties of iron minerals in atmospheric dust can be better understood using techniques of rock magnetism (measurements at 5-300 K), Mössbauer and high-resolution visible and near-infrared reflectance spectroscopy; chemical reactivity of iron oxide phases; and electron microscopy for observing directly the ferric oxide coatings and particles. These studies can elucidate the diverse environmental effects of iron oxides in dust and can help to identify dust-source areas. Dust-source sediments from the North American Great Basin and Colorado Plateau deserts and the Kalahari Desert, southern Africa, were used to compare average reflectance values with a magnetic parameter (hard isothermal remanent magnetization, HIRM) for ferric oxide abundance. Lower reflectance values correspond strongly with higher HIRM values, indicating that ferric oxides (hematite or goethite, or both) contribute to absorption of solar radiation in these sediments. Dust deposited to snow cover of the San Juan Mountains (Colorado) and Wasatch Mountains (Utah) was used to characterize dust composition compared with properties of sediments exposed in source-areas identified from satellite retrievals. Results from multiple methods indicate that

MEASUREMENT OF FUGITIVE EMISSIONS AT A BIOREACTOR LANDFILL

Science.gov (United States)

This report focuses on three field campaigns performed in 2002 and 2003 to measure fugitive emissions at a bioreactor landfill in Louisville, KY, using an open-path Fourier transform infrared spectrometer. The study uses optical remote sensing-radial plume mapping. The horizontal...

Quantifying the relative contribution of natural gas fugitive emissions to total methane emissions in Colorado and Utah using mobile stable isotope (13CH4) analysis

Science.gov (United States)

Rella, Chris; Jacobson, Gloria; Crosson, Eric; Karion, Anna; Petron, Gabrielle; Sweeney, Colm

2013-04-01

Fugitive emissions of methane into the atmosphere are a major concern facing the natural gas production industry. Because methane is more energy-rich than coal per kg of CO2 emitted into the atmosphere, it represents an attractive alternative to coal for electricity generation. However, given that the global warming potential of methane is many times greater than that of carbon dioxide (Solomon et al. 2007), the importance of quantifying the fugitive emissions of methane throughout the natural gas production and distribution process becomes clear (Howarth et al. 2011). A key step in the process of assessing the emissions arising from natural gas production activities is partitioning the observed methane emissions between natural gas fugitive emissions and other sources of methane, such as from landfills or agricultural activities. One effective method for assessing the contribution of these different sources is stable isotope analysis. In particular, the 13CH4 signature of natural gas (-35 to -40 permil) is significantly different that the signature of other significant sources of methane, such as landfills or ruminants (-45 to -70 permil). In this paper we present measurements of mobile field 13CH4 using a spectroscopic stable isotope analyzer based on cavity ringdown spectroscopy, in two intense natural gas producing regions of the United States: the Denver-Julesburg basin in Colorado, and the Uintah basin in Utah. Mobile isotope measurements in the nocturnal boundary layer have been made, over a total path of 100s of km throughout the regions, allowing spatially resolved measurements of the regional isotope signature. Secondly, this analyzer was used to quantify the isotopic signature of those individual sources (natural gas fugitive emissions, concentrated animal feeding operations, and landfills) that constitute the majority of methane emissions in these regions, by making measurements of the isotope ratio directly in the downwind plume from each source. These

Iron oxide minerals in dust-source sediments from the Bodélé Depression, Chad: Implications for radiative properties and Fe bioavailability of dust plumes from the Sahara

Science.gov (United States)

Moskowitz, Bruce M; Reynolds, Richard L.; Goldstein, Harland L.; Beroquo, Thelma; Kokaly, Raymond F.; Bristow, Charlie S

2016-01-01

Atmospheric mineral dust can influence climate and biogeochemical cycles. An important component of mineral dust is ferric oxide minerals (hematite and goethite) which have been shown to influence strongly the optical properties of dust plumes and thus affect the radiative forcing of global dust. Here we report on the iron mineralogy of dust-source samples from the Bodélé Depression (Chad, north-central Africa), which is estimated to be Earth’s most prolific dust producer and may be a key contributor to the global radiative budget of the atmosphere as well as to long-range nutrient transport to the Amazon Basin. By using a combination of magnetic property measurements, Mössbauer spectroscopy, reflectance spectroscopy, chemical analysis, and scanning electron microscopy, we document the abundance and relative amounts of goethite, hematite, and magnetite in dust-source samples from the Bodélé Depression. The partition between hematite and goethite is important to know to improve models for the radiative effects of ferric oxide minerals in mineral dust aerosols. The combination of methods shows (1) the dominance of goethite over hematite in the source sediments, (2) the abundance and occurrences of their nanosize components, and (3) the ubiquity of magnetite, albeit in small amounts. Dominant goethite and subordinate hematite together compose about 2% of yellow-reddish dust-source sediments from the Bodélé Depression and contribute strongly to diminution of reflectance in bulk samples. These observations imply that dust plumes from the Bodélé Depression that are derived from goethite-dominated sediments strongly absorb solar radiation. The presence of ubiquitous magnetite (0.002–0.57 wt%) is also noteworthy for its potentially higher solubility relative to ferric oxide and for its small sizes, including PM bioavailability to marine and terrestrial ecosystems.

Present and Past Impact of Glacially Sourced Dust on Iron Fertilization of the Southern Ocean

Science.gov (United States)

Shoenfelt, E. M.; Winckler, G.; Kaplan, M. R.; Sambrotto, R.; Bostick, B. C.

2016-12-01

An increase in iron-containing dust flux and a more efficient biological pump in the Southern Ocean have been associated with the CO2 drawdown and global cooling of the Last Glacial Maximum (LGM). While iron (Fe) mineralogy is known to affect Fe bioavailability through its impact on Fe solubility, there are limited studies investigating the importance of Fe mineralogy in dust fluxes to the Southern Ocean, and no previous studies investigating interactions between eukaryotic phytoplankton and particulate-phase Fe in natural dusts applicable to Southern Ocean environments. Since physically weathered bedrock becomes less soluble as it becomes weathered and oxidized, we hypothesized that glacially sourced dusts would contain more Fe(II)-rich primary minerals and would be more bioavailable than dusts from areas not impacted by glaciers. We used a series of natural dusts from Patagonia as the sole Fe source in incubation experiments with the model diatom Phaeodactylum tricornutum, and evaluated Fe bioavailability using culture growth rates, cell density, and variable fluorescence. Monod curves were also used to evaluate the efficiency of the different particulates as sources of nutrient Fe. Using these Monod curves fit to growth rates plotted against particulate Fe concentrations, we observed that 1) Fe(II)-rich primary silicates were significantly more effective as an Fe source to diatoms than Fe(III)-rich oxides, that 2) Fe(II) content itself was responsible for the difference in Fe bioavailability/efficiency of the Fe nutrient source, and that 3) surface interactions with the particulates were important. In an effort to explore the possibility that Fe mineralogy impacted Fe bioavailability in past oceans, we will present our hypotheses regarding productivity and Fe mineralogy/bioavailability through the last glacial cycle.

Ice Nucleating Particle Properties in the Saharan Air Layer Close to the Dust Source

Science.gov (United States)

Boose, Y.; Garcia, I. M.; Rodríguez, S.; Linke, C.; Schnaiter, M.; Nickovic, S.; Lohmann, U.; Kanji, Z. A.; Sierau, B.

2015-12-01

In August 2013 and 2014 measurements of ice nucleating particle (INP) concentrations, aerosol particle size distributions, chemistry and fluorescence were conducted at the Izaña Atmospheric Observatory located at 2373 m asl on Tenerife, west off the African shore. During summer, the observatory is frequently within the Saharan Air Layer and thus often exposed to dust. Absolute INP concentrations and activated fractions at T=-40 to -15°C and RHi=100-150 % were measured. In this study, we discuss the in-situ measured INP properties with respect to changes in the chemical composition, the biological content, the source regions as well as transport pathways and thus aging processes of the dust aerosol. For the first time, ice crystal residues were also analyzed with regard to biological content by means of their autofluorescence signal close to a major dust source region. Airborne dust samples were collected with a cyclone for additional offline analysis in the laboratory under similar conditions as in the field. Both, in-situ and offline dust samples were chemically characterized using single-particle mass spectrometry. The DREAM8 dust model extended with dust mineral fractions was run to simulate meteorological and dust aerosol conditions for ice nucleation. Results show that the background aerosol at Izaña was dominated by carbonaceous particles, which were hardly ice-active under the investigated conditions. When Saharan dust was present, INP concentrations increased by up to two orders of magnitude even at water subsaturated conditions at T≤-25°C. Differences in the ice-activated fraction were found between different dust periods which seem to be linked to variations in the aerosol chemical composition (dust mixed with changing fractions of sea salt and differences in the dust aerosol itself). Furthermore, two biomass burning events in 2014 were identified which led to very low INP concentrations under the investigated temperature and relative humidity

Geochemical evidence on the source regions of Tibetan Plateau dusts during non-monsoon period in 2008/09

Science.gov (United States)

Li, C.; Kang, S.; Zhang, Q.; Gao, S.

2012-12-01

Geochemical characteristics, source regions and related transport patterns of dust over the Tibetan Plateau (TP) are still unclear. To address these issues, major (Na, Mg, Al, K and Ca), trace (e.g. Li, Cr, Ni, As, Cd, Cs, Pb and U) and rare earth elements of dust samples from five snow-pits over the TP and its fringe areas during the non-monsoon period in 2008/2009 were analyzed. The results indicate that rare earth element compositions of snow-pit dust are similar to those of the upper continental crust. Enrichment factors of all the elements of snow-pit dust are identical to those of the pollution elements (e.g. Cu and Ni) and elements like Li, As and Cs that are concentrated in surface soils. In contrast, concentrations of some typical pollution elements (e.g. Cr and Cd) of snow pit dust are lower than those of dusts derived from the Sahara Desert and the Thar Desert surrounding the TP. Additionally, the compositions of rare earth elements and high field strength elements (Hf, Zr and Nb) of snow-pit dust are also similar to those of surface soils and different from dusts of these two deserts. The combined evidence, including dust transport patterns around the TP, supports the conclusion that the TP itself is the main source region of snow-pit dusts of the inner TP. It is unlikely that those particle-bound pollutants are transported into the TP from outside sources during the non-monsoon period. Ratios of Ce/Sm against Eu/Sm for the snow-pit dust, fine dust from the Sahara desert (A), and ratios of Ce/Er against Eu/Er for the snow-pit dust, fine dust from the Thar Desert (B). Dust from Sahasa cannot penetrate into the TP and transport only along the Himalayas at south and the Tianshan at north due to their high elevation

Optical and microphysical properties of natural mineral dust and anthropogenic soil dust near dust source regions over northwestern China

Directory of Open Access Journals (Sweden)

X. Wang

2018-02-01

Full Text Available Mineral dust aerosols (MDs not only influence the climate by scattering and absorbing solar radiation but also modify cloud properties and change the ecosystem. From 3 April to 16 May 2014, a ground-based mobile laboratory was deployed to measure the optical and microphysical properties of MDs near dust source regions in Wuwei, Zhangye, and Dunhuang (in chronological order along the Hexi Corridor over northwestern China. Throughout this dust campaign, the hourly averaged (±standard deviation aerosol scattering coefficients (σsp, 550 nm of the particulates with aerodynamic diameters less than 2.5 µm (PM2.5 at these three sites were sequentially 101.5 ± 36.8, 182.2 ± 433.1, and 54.0 ± 32.0 Mm−1. Correspondingly, the absorption coefficients (σap, 637 nm were 9.7 ± 6.1, 6.0 ± 4.6, and 2.3 ± 0.9 Mm−1; single-scattering albedos (ω, 637 nm were 0.902 ± 0.025, 0.931 ± 0.037, and 0.949 ± 0.020; and scattering Ångström exponents (Åsp, 450–700 nm of PM2.5 were 1.28 ± 0.27, 0.77 ± 0.51, and 0.52 ± 0.31. During a severe dust storm in Zhangye (i.e., from 23 to 25 April, the highest values of σsp2.5 ( ∼  5074 Mm−1, backscattering coefficient (σbsp2.5,  ∼  522 Mm−1, and ω637 ( ∼  0.993 and the lowest values of backscattering fraction (b2.5,  ∼  0.101 at 550 nm and Åsp2.5 ( ∼  −0.046 at 450–700 nm, with peak values of aerosol number size distribution (appearing at the particle diameter range of 1–3 µm, exhibited that the atmospheric aerosols were dominated by coarse-mode dust aerosols. It is hypothesized that the relatively higher values of mass scattering efficiency during floating dust episodes in Wuwei and Zhangye are attributed to the anthropogenic soil dust produced by agricultural cultivations.

Measuring Dust Emission from the Mojave Desert (USA) by Daily Remote-Camera Observations and Wind-Erosion Measurements: Bearing on "Unseen" Sources and Global Dust Abundance

Science.gov (United States)

Reynolds, R. L.; Urban, F.; Goldstein, H. L.; Fulton, R.

2017-12-01

A large gap in understanding the effects of atmospheric dust at all spatial scales is uncertainty about how much and whence dust is emitted annually. Digital recording of dust emission at high spatial and temporal resolution would, together with periodic flux measurements, support improved estimates of local-scale dust flux where infrastructure could support remote internet enabled cameras. Such recording would also elucidate wind-erosion dynamics when combined with meteorological data. Remote camera recording of dust-emitting settings on and around Soda Lake (Mojave Desert) was conducted every 15 minutes during daylight between 10 Nov. 2010 and 31 Dec. 2016 and images uploaded to a web server. Examination of 135,000 images revealed frequent dust events, termed "dust days" when plumes obscured mountains beyond source areas. Such days averaged 68 (sd=10) per year (2011 through 2016). We examined satellite retrievals (MODIS, GOES) for dust events during six cloudless days of highest and longest duration dust emission but none were observed. From Apr. 2000 through May 2013, aeolian sediments collected at three sites were sampled and weighed. Estimates of the emitted mass of silt- and clay-size fractions were made on the basis of measured horizontal mass flux, particle sizes of sediment in collectors, and roughly determined areas of dust generation. Over this period, nearly 4 Tg yr-1 of dust (as particulate matter flood in the basin in late Dec. 2010 that deposited flood sediment across the lake basin. Increased emission was likely related to the availability of fresh, unanchored flood sediment. Within the Mojave and Great Basin deserts of North America, many settings akin to those at Soda Lake similarly emit dust that is rarely detected in satellite retrievals. These findings strongly imply that local and regional dust emissions from western North America are far underestimated and that, by extension to relatively small dust-source areas across all drylands, global

Monitoring of fugitive emissions in petrochemical plant

Energy Technology Data Exchange (ETDEWEB)

Brandao, Rozilda F [Companhia Petroquimica do Nordeste (COPENE), Camacari, BA (Brazil). Div. de Engenharia Ambiental

1994-12-31

COPENE (Petroquimica do Nordeste S/A) has been implanting a program of fugitive emissions adapted to its reality, trying to promote a continuous improvement in its employees` working conditions and in environmental protection. This paper presents the methodology for the elaboration of this program and the conclusions of some surveys which were already completed (author). 4 refs., 7 figs., 3 tabs.

Monitoring of fugitive emissions in petrochemical plant

Energy Technology Data Exchange (ETDEWEB)

Brandao, Rozilda F. [Companhia Petroquimica do Nordeste (COPENE), Camacari, BA (Brazil). Div. de Engenharia Ambiental

1993-12-31

COPENE (Petroquimica do Nordeste S/A) has been implanting a program of fugitive emissions adapted to its reality, trying to promote a continuous improvement in its employees` working conditions and in environmental protection. This paper presents the methodology for the elaboration of this program and the conclusions of some surveys which were already completed (author). 4 refs., 7 figs., 3 tabs.

40 CFR 63.7291 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Science.gov (United States)

2010-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? 63... meet for fugitive pushing emissions if I have a by-product coke oven battery with vertical flues? (a... existing by-product coke oven battery with vertical flues. (1) Observe and record the opacity of fugitive...

Localization of fugitive methane emission from natural gas distribution network of Titas Gas

Directory of Open Access Journals (Sweden)

Mandal Pradip C.

2017-03-01

Full Text Available The aim of this paper is to localize the fugitive leaks from the above ground facilities of the existing system of Titas Gas (TG after developing mathematical model for fugitive emission. Soap screening techniques and Gasurveyor 500 series instrument were used in this study for detecting potential leaks. Leaked gas was quantified using either Hi-Flow gas sampler or bagging measurements system. The results show that the respective potential gas leaking point of City Gate Station (CGS, commercial Regulating and Metering Station (RMS, industrial RMS, residential RMS and Town Bordering Station (TBS/ District Regulating Station (DRS are scrubber dump valve (average leak rate 217.00 L/min, insulating point (average leak rate 4.04 L/min, tube fitting connector (average leak rate 8.00 L/min, connector (average leak rate 1.55 L/min and pressure relief valve (average leak rate 437.92 L/min. Fugitive methane emission can be reduced by stopping leaks of fittings or components having high KLeak value.

Sedimentary and mineral dust sources of dissolved iron to the world ocean

Directory of Open Access Journals (Sweden)

J. K. Moore

2008-05-01

from sinking particles; and 3 an improved sedimentary source for dissolved iron. Most scavenged iron (90% is put on sinking particles to remineralize deeper in the water column. The model-observation differences are reduced with these modifications. The improved BEC model is used to examine the relative contributions of mineral dust and marine sediments in driving dissolved-iron distributions and marine biogeochemistry. Mineral dust and sedimentary sources of iron contribute roughly equally, on average, to dissolved iron concentrations. The sedimentary source from the continental margins has a strong impact on open-ocean iron concentrations, particularly in the North Pacific. Plumes of elevated dissolved-iron concentrations develop at depth in the Southern Ocean, extending from source regions in the SW Atlantic and around New Zealand. The lower particle flux and weaker scavenging in the Southern Ocean allows the continental iron source to be advected far from sources. Both the margin sediment and mineral dust Fe sources substantially influence global-scale primary production, export production, and nitrogen fixation, with a stronger role for the dust source. Ocean biogeochemical models that do not include the sedimentary source for dissolved iron, will overestimate the impact of dust deposition variations on the marine carbon cycle. Available iron observations place some strong constraints on ocean biogeochemical models. Model results should be evaluated against both surface and subsurface Fe observations in the waters that supply dissolved iron to the euphotic zone.

Sr-Nd-Hf Isotopic Analysis of <10 mg Dust Samples: Implications for Ice Core Dust Source Fingerprinting

DEFF Research Database (Denmark)

Ujvari, Gabor; Wegner, Wencke; Klötzli, Urs

2018-01-01

Combined Sr‐Nd‐Hf isotopic data of two reference materials (AGV‐1/BCR2) and 50, 10, and 5 mg aliquots of carbonate‐free fine grain (isotopic...... compositions (ICs) demonstrate that robust isotopic ratios can be obtained from 5 to 10 mg size rock samples using the ion exchange/mass spectrometry techniques applied. While 87Sr/86Sr ratios of dust aluminosilicate fractions are affected by even small changes in pretreatments, Nd isotopic ratios are found...... to be insensitive to acid leaching, grain‐size or weathering effects. However, the Nd isotopic tracer is sometimes inconclusive in dust source fingerprinting (BEI and NUS both close to ɛNd(0) –10). Hafnium isotopic values (

CHARACTERIZATION OF MUD/DIRT CARRYOUT ONTO PAVED ROADS FROM CONSTRUCTION AND DEMOLITION ACTIVITIES

Science.gov (United States)

The report characterizes fugitive dust generated by vehicular traffic on paved streets and highways resulting from mud/dirt carryout from unpaved areas as a primary source of PM-10 (particles = or < 10 micrometers in aerodynamic diameter), and evaluates three technologies for eff...

Rotating dust ring in an RF discharge coupled with a dc-magnetron sputter source. Experiment and simulation

International Nuclear Information System (INIS)

Matyash, K; Froehlich, M; Kersten, H; Thieme, G; Schneider, R; Hannemann, M; Hippler, R

2004-01-01

During an experiment involving coating of dust grains trapped in an RF discharge using a sputtering dc-magnetron source, a rotating dust ring was observed and investigated. After the magnetron was switched on, the dust cloud levitating above the RF electrode formed a ring rotating as a rigid body. Langmuir probe diagnostics were used for the measurement of plasma density and potential. It was discovered that the coupling of the dc-magnetron source to the RF discharge causes steep radial gradients in electron density and plasma potential. The rotation of the dust ring is attributed to the azimuthal component of the ion drag force, which appears due to the azimuthal drift of the ions caused by crossed radial electric and axial magnetic fields. In order to get more insight into the mechanism of dust ring rotation, a Particle-in-Cell simulation of a rotating dust cloud was performed. The results of the experiment and simulation are presented and discussed

Rotating dust ring in an RF discharge coupled with a dc-magnetron sputter source. Experiment and simulation

Energy Technology Data Exchange (ETDEWEB)

Matyash, K [Institut fuer Niedertemperaturplasmaphysik Greifswald, Fr.-L.-Jahn-Strasse 19, 17489 Greifswald (Germany); Froehlich, M [Institut fuer Physik, Ernst-Moritz-Arndt-Universitaet Greifswald, Domstrasse 10a, 17487 Greifswald (Germany); Kersten, H [Institut fuer Niedertemperaturplasmaphysik Greifswald, Fr.-L.-Jahn-Strasse 19, 17489 Greifswald (Germany); Thieme, G [Institut fuer Physik, Ernst-Moritz-Arndt-Universitaet Greifswald, Domstrasse 10a, 17487 Greifswald (Germany); Schneider, R [Max-Planck-Institut fuer Plasmaphysik, Teilinstitut Greifswald, Wendelsteinstrasse 1, 17489 Greifswald (Germany); Hannemann, M [Institut fuer Niedertemperaturplasmaphysik Greifswald, Fr.-L.-Jahn-Strasse 19, 17489 Greifswald (Germany); Hippler, R [Institut fuer Physik, Ernst-Moritz-Arndt-Universitaet Greifswald, Domstrasse 10a, 17487 Greifswald (Germany)

2004-10-07

During an experiment involving coating of dust grains trapped in an RF discharge using a sputtering dc-magnetron source, a rotating dust ring was observed and investigated. After the magnetron was switched on, the dust cloud levitating above the RF electrode formed a ring rotating as a rigid body. Langmuir probe diagnostics were used for the measurement of plasma density and potential. It was discovered that the coupling of the dc-magnetron source to the RF discharge causes steep radial gradients in electron density and plasma potential. The rotation of the dust ring is attributed to the azimuthal component of the ion drag force, which appears due to the azimuthal drift of the ions caused by crossed radial electric and axial magnetic fields. In order to get more insight into the mechanism of dust ring rotation, a Particle-in-Cell simulation of a rotating dust cloud was performed. The results of the experiment and simulation are presented and discussed.

Saccharide Composition in Fine and Coarse Particulate Matter and Soils in Central Arizona and Use of Saccharides as Molecular Markers for Source Apportionment

Science.gov (United States)

Jia, Y.; Clements, A.; Fraser, M.

2009-04-01

The desert southwestern United States routinely exceeds health-based standards for coarse particulate matter [1]. PM10 concentrations are high in both urban and rural areas and are believed to originate from fugitive dust emissions from agricultural fields and roads and soil erosion from the surrounding desert locations. Soil together with its associated biota contains a complex mixture of biogenic detritus, including plant detritus, airborne microbes comprised of bacteria, viruses, spores of lichens and fungi, small algae, and protozoan cysts [4][5], which can mostly become airborne when winds are strong enough and soil dry enough to be re-entrained into the atmosphere [3]. Other potential sources to PM10 may include primary biological aerosol particles (PBAPs), given a multitude of flower, grass, and fungal species that thrive in the Sonoran desert and actively release pollens and spores throughout the year [2]. However, because soil and fugitive dust is also believed to contain a large number of these biological particles and is considered as a secondary host of PBAPs [3] [4], the role and contribution of PBAPs as a direct ambient PM source in the desert southwest have not been clearly stated or investigated. In an effort to identify and assess the relative contribution of these and other major PM sources in the southwestern US region, and particularly to assess the contribution from soil and fugitive dust, a series of ambient PM samples and soil samples were collected in Higley, AZ, USA, a suburb of the Phoenix metropolitan area which has seen rapid urban sprawl onto agricultural lands. Because of their suggested ability to track biologically important organic materials from natural environment [4][6][7][8][9][10], saccharides were chosen as the key compounds to trace the release of soil dusts into the atmosphere, and to elucidate other major sources that contribute to the PM levels in this location in the arid southwestern US. To this end, saccharide compounds

Herschel-ATLAS: Dust Temperature and Redshift Distribution of SPIRE and PACS Detected Sources Using Submillimetre Colours

Science.gov (United States)

Amblard, A.; Cooray, Asantha; Serra, P.; Temi, P.; Barton, E.; Negrello, M.; Auld, R.; Baes, M.; Baldry, I. K.; Bamford, S.;

Development of Briquette from Coir Dust and Rice Husk Blend: An Alternative Energy Source

Directory of Open Access Journals (Sweden)

Md. Hamidul Islam

2014-05-01

Full Text Available Biomass is one of the predominant renewable energy sources and the use of biomass for the energy generation has got much attention due to its environmental friendliness. Densification of coir dust into fuel briquette can solve waste disposal problem as well as can serve as an alternative energy source. The objective of this study was to investigate the possibility of producing briquette from coir dust and rice husk blend without binder. During this study, a briquetting experiment was conducted with different coir dust and rice husk blends (i.e. coir dust and rice husk ratio of 80:20, 60:40, 50:50, 40:60, 20:80 and 0:100. Briquetting operation was performed using a die-screw press type briquetting machine. The briquettes were tested to evaluate their density, compressive strength, calorific value, burning rate and water vaporizing capacity and it was found that mixing ratio had a significant effect on the physical, mechanical and combustion properties of the coir dust-rice husk briquettes. Density, compressive strength and calorific value and water vaporizing capacity were increased with increasing mixing ratio while burning rate was decreased. Coir dust-rice husk briquettes with mixing ratio of 20:80 had higher density (1.413 g/cm3, compressive strength (218.4 N/cm2, calorific value (4879 kcal/kg, water vaporizing capacity (0.853 l/kg and low burning rate (0.783 kg/hour followed by the mixing ratio 40:60, 50:50, 60:40 and 0:100. The results indicate that coir dust and rice husk blend briquettes were found to have better overall handling characteristics over rice husk briquette. However, production of briquettes from coir dust and rice husk at mixing ratio of 50:50 was found to be more suitable for commercial application in terms of cost effectiveness.

Source apportionment of PM10 mass and particulate carbon in the Kathmandu Valley, Nepal

Science.gov (United States)

Kim, Bong Mann; Park, Jin-Soo; Kim, Sang-Woo; Kim, Hyunjae; Jeon, Haeun; Cho, Chaeyoon; Kim, Ji-Hyoung; Hong, Seungkyu; Rupakheti, Maheswar; Panday, Arnico K.; Park, Rokjin J.; Hong, Jihyung; Yoon, Soon-Chang

2015-12-01

The Kathmandu Valley in Nepal is a bowl-shaped urban basin in the Himalayan foothills with a serious problem of fine particulate air pollution that impacts local health and impairs visibility. Particulate carbon concentrations have reached severe levels that threaten the health of 3.5 million local residents. Moreover, snow and ice on the Himalayan mountains are melting as a result of additional warming due to particulate carbon, especially high black carbon concentrations. To date, the sources of the Valley's particulate carbon and the impacts of different sources on particulate carbon concentrations are not well understood. Thus, before an effective control strategy can be developed, these particulate carbon sources must be identified and quantified. Our study has found that the four primary sources of particulate carbon in the Kathmandu Valley during winter are brick kilns, motor vehicles, fugitive soil dust, and biomass/garbage burning. Their source contributions are quantified using a recently developed new multivariate receptor model SMP. In contrast to other highly polluted areas such as China, secondary contribution is almost negligible in Kathmandu Valley. Brick kilns (40%), motor vehicles (37%) and biomass/garbage burning (22%) have been identified as the major sources of elemental carbon (black carbon) in the Kathmandu Valley during winter, while motor vehicles (47%), biomass/garbage burning (32%), and soil dust (13%) have been identified as the most important sources of organic carbon. Our research indicates that controlling emissions from motor vehicles, brick kilns, biomass/garbage burning, and soil dust is essential for the mitigation of the particulate carbon that threatens public health, impairs visibility, and influences climate warming within and downwind from the Kathmandu Valley. In addition, this paper suggests several useful particulate carbon mitigation methods that can be applied to Kathmandu Valley and other areas in South Asia with

Two-dimensional transport of dust from an infinite line source at ground level: non-zero roughness height

International Nuclear Information System (INIS)

Hassan, M.H.A.; Eltayeb, I.A.

1992-07-01

The previous study (Eltayeb and Hassan, 1992) of the two-dimensional diffusion equation of dust over a rough ground surface, which acts as a dust source of variable strength, under the influence of horizontal wind and gravitational attraction is here extended to all finite values of the roughness height Z 0 . An analytic expression is obtained for the concentration of dust for a general strength of the source. The result reduces to the previously known solutions as special cases. The expression for the concentration has been evaluated for some representative example of the source strength g(X). It is found that the concentration decreases with roughness height at any fixed point above ground level. (author). 4 refs, 2 figs

Magnetic characteristics of industrial dust from different sources of emission: A case study of Poland

Science.gov (United States)

Szuszkiewicz, Marcin; Magiera, Tadeusz; Kapička, Aleš; Petrovský, Eduard; Grison, Hanna; Gołuchowska, Beata

2015-05-01

Dust emission and deposition in topsoil have negative effect on individual components of the ecosystem. In addition to routine geochemical analyses, magnetic measurements may provide useful complementary information related to the type, concentration and grain-size distribution of the technogenic magnetic particles (TMPs) and thus the degree of contamination of the environment. The aim of this contribution is to use magnetic parameters in distinguishing dust from a wide range of sources of air pollution (power industry, cement, coke, ceramic industries and biomass combustion). We measured magnetic susceptibility, hysteresis parameters and thermomagnetic curves. Our results suggest that predominant component in tested samples is magnetite, only dust from coking plant and the combustion of lignite contained also maghemite and/or hematite. Mixture of sizes, ranging from fine single-domain to coarse multi-domain grains, was detected. Our results indicate that industrial dusts from various sources of emissions have different specific magnetic properties and magnetic measurements may provide very helpful information.

PM10 standards and nontraditional particulate source controls: A summary of the A ampersand WMA/EPA international specialty conference

International Nuclear Information System (INIS)

Chow, J.C.; Watson, J.G.; Ono, D.M.; Mathai, C.V.

1993-01-01

An international specialty conference, jointly sponsored by the Air ampersand Waste Management Association (A ampersand WMA) and the US Environmental Protection Agency (EPA), entitled open-quotes PM 10 Standards and Nontraditional Particulate Source Controls,close quotes was held in Scottsdale, Arizona, January 12-15, 1992. The conference included 92 presentations in 17 technical sessions. Eight-one peer-reviewed technical papers, two keynote addresses and one panel session summary describing novel applications, measurement processes, modeling techniques and control measures for nontraditional pollution sources are assembled in the Transactions. The technical issues addressed during the conference included: (1) measurement methods and data bases; (2) emissions source characterization; (3) source apportionment of nontraditional sources; (4) fugitive dust characterization and control technologies; (5) vegetative burning characterization and control technologies; (6) sources and controls of secondary aerosol and motor vehicle precursors; and (7) regulatory policies and State Implementation Plan (SIP) development. This paper gives an overview of the technical program. 105 refs., 1 tab

Iron oxide minerals in dust-source sediments from the Bodélé Depression, Chad: Implications for radiative properties and Fe bioavailability of dust plumes from the Sahara

Science.gov (United States)

Moskowitz, Bruce M; Reynolds, Richard L.; Goldstein, Harland L.; Beroquo, Thelma; Kokaly, Raymond F.; Bristow, Charlie S

2016-01-01

Atmospheric mineral dust can influence climate and biogeochemical cycles. An important component of mineral dust is ferric oxide minerals (hematite and goethite) which have been shown to influence strongly the optical properties of dust plumes and thus affect the radiative forcing of global dust. Here we report on the iron mineralogy of dust-source samples from the Bodélé Depression (Chad, north-central Africa), which is estimated to be Earth’s most prolific dust producer and may be a key contributor to the global radiative budget of the atmosphere as well as to long-range nutrient transport to the Amazon Basin. By using a combination of magnetic property measurements, Mössbauer spectroscopy, reflectance spectroscopy, chemical analysis, and scanning electron microscopy, we document the abundance and relative amounts of goethite, hematite, and magnetite in dust-source samples from the Bodélé Depression. The partition between hematite and goethite is important to know to improve models for the radiative effects of ferric oxide minerals in mineral dust aerosols. The combination of methods shows (1) the dominance of goethite over hematite in the source sediments, (2) the abundance and occurrences of their nanosize components, and (3) the ubiquity of magnetite, albeit in small amounts. Dominant goethite and subordinate hematite together compose about 2% of yellow-reddish dust-source sediments from the Bodélé Depression and contribute strongly to diminution of reflectance in bulk samples. These observations imply that dust plumes from the Bodélé Depression that are derived from goethite-dominated sediments strongly absorb solar radiation. The presence of ubiquitous magnetite (0.002–0.57 wt%) is also noteworthy for its potentially higher solubility relative to ferric oxide and for its small sizes, including PM iron apportionment is estimated at about 33% in ferric oxide minerals, 1.4% in magnetite, and 65% in ferric silicates. Structural iron in clay

Arabian Red Sea coastal soils as potential mineral dust sources

KAUST Repository

Prakash, P. Jish

2016-09-26

Both Moderate Resolution Imaging Spectroradiometer (MODIS) and Spinning Enhanced Visible and InfraRed Imager (SEVIRI) satellite observations suggest that the narrow heterogeneous Red Sea coastal region is a frequent source of airborne dust that, because of its proximity, directly affects the Red Sea and coastal urban centers. The potential of soils to be suspended as airborne mineral dust depends largely on soil texture, moisture content and particle size distributions. Airborne dust inevitably carries the mineralogical and chemical signature of a parent soil. The existing soil databases are too coarse to resolve the small but important coastal region. The purpose of this study is to better characterize the mineralogical, chemical and physical properties of soils from the Arabian Red Sea coastal plain, which in turn will help to improve assessment of dust effects on the Red Sea, land environmental systems and urban centers. Thirteen surface soils from the hot-spot areas of windblown mineral dust along the Red Sea coastal plain were sampled for analysis. Analytical methods included optical microscopy, X-ray diffraction (XRD), inductively coupled plasma optical emission spectrometry (ICP-OES), ion chromatography (IC), scanning electron microscopy (SEM) and laser particle size analysis (LPSA). We found that the Red Sea coastal soils contain major components of quartz and feldspar, as well as lesser but variable amounts of amphibole, pyroxene, carbonate, clays and micas, with traces of gypsum, halite, chlorite, epidote and oxides. The range of minerals in the soil samples was ascribed to the variety of igneous and metamorphic provenance rocks of the Arabian Shield forming the escarpment to the east of the Red Sea coastal plain. The analysis revealed that the samples contain compounds of nitrogen, phosphorus and iron that are essential nutrients to marine life. The analytical results from this study will provide a valuable input into dust emission models used in climate

Source apportionment and environmental fate of lead chromates in atmospheric dust in arid environments.

Science.gov (United States)

Meza-Figueroa, Diana; González-Grijalva, Belem; Romero, Francisco; Ruiz, Joaquin; Pedroza-Montero, Martín; Rivero, Carlos Ibañez-Del; Acosta-Elías, Mónica; Ochoa-Landin, Lucas; Navarro-Espinoza, Sofía

2018-03-07

The environmental fate of lead derived from traffic paint has been poorly studied in developing countries, mainly in arid zones. For this purpose, a developing city located in the Sonoran desert (Hermosillo, Mexico), was chosen to conduct a study. In this paper the lead chromate (crocoite) sources in atmospheric dust were addressed using a combination of Raman microspectroscopy, X-ray diffraction, scanning electron microscopy (SEM), and Pb isotope measurements. A high concentration of Pb and Cr as micro- and nanostructured pigments of crocoite is reported in yellow traffic paint (n=80), road dust (n=146), settled dust in roofs (n=21), and atmospheric dust (n=20) from a developing city located in the Sonoran Desert. 10 samples of peri-urban soils were collected for local geochemical background. The paint photodegradation and erosion of the asphaltic cover are enhanced by the climate, and the presence of the mineral crocoite (PbCrO 4 ) in road dust with an aerodynamic diameter ranging from 100nm to 2μm suggests its integration into the atmosphere by wind resuspension processes. A positive PbCr correlation (R 2 =0.977) was found for all studied samples, suggesting a common source. The Pb-isotope data show signatures in atmospheric dust as a product of the mixing of two end members: i) local soils and ii) crocoite crystals as pigments in paint. The presence of lead chromates in atmospheric dust has not been previously documented in Latin America, and it represents an unknown health risk to the exposed population because the identified size of crystals can reach the deepest part of lungs. Copyright © 2018 Elsevier B.V. All rights reserved.

Change of the Asian dust source region deduced from the composition of anthropogenic radionuclides in surface soil in Mongolia

Directory of Open Access Journals (Sweden)

Y. Igarashi

2011-07-01

Full Text Available Recent climate change, especially during the 2000s, may be the primary reason for the expansion of the Asian dust source region. The change in the dust source region was investigated by examining anthropogenic radionuclides contained in surface soil samples from Mongolia. Surface soil was globally labeled by radioactive fallout from nuclear testing during the late 1950s and early 1960s, but there are no current direct sources for anthropogenic radionuclides in the air (before the Fukushima nuclear power plant accident in 2011. Radionuclides in the atmosphere are therefore carried mainly by wind-blown dust from surface soil, that is, aeolian dust. Asian dust carries traces of ⁹⁰Sr, ¹³⁷Cs, and other anthropogenic radionuclides; the heaviest deposition occurs in spring and has been recorded in Japan since the early 1990s. The composition of anthropogenic radionuclides in atmospheric depositions would be affected by a change in the dust source. Previous studies of atmospheric deposition at long-term monitoring sites (e.g. in Tsukuba, Japan have detected changes in the ¹³⁷Cs/⁹⁰Sr ratio and in the specific activity of the radionuclides. These changes in the composition of observed atmospheric depositions are supposed to reflect changes in the climatic conditions of the dust source region. To investigate this dust source change, we conducted a field survey of radionuclides (⁹⁰Sr and ¹³⁷Cs in surface soil samples in September 2007 in the eastern and southern regions of Mongolia, where dust storms have occurred more frequently since 2000. The specific activities of both radionuclides as well as the ¹³⁷Cs/⁹⁰Sr ratio in the surface soil were well correlated with annual average precipitation in the Mongolian desert-steppe zone. Higher specific activities and a higher ¹³⁷Cs/⁹⁰Sr ratio were found in grassland regions that experienced greater

Quantifying the relative contribution of natural gas fugitive emissions to total methane emissions in Colorado, Utah, and Texas using mobile δ13CH4 analysis

Science.gov (United States)

Rella, C.; Crosson, E.; Petron, G.; Sweeney, C.; Karion, A.

2013-12-01

Fugitive emissions of methane into the atmosphere are a major concern facing the natural gas production industry. Because methane is more energy-rich than coal per kg of CO2 emitted into the atmosphere, it represents an attractive alternative to coal for electricity generation, provided that the fugitive emissions of methane are kept under control. A key step in assessing these emissions in a given region is partitioning the observed methane emissions between natural gas fugitive emissions and other sources of methane, such as from landfills or agricultural activities. One effective method for assessing the contribution of these different sources is stable isotope analysis, using the δ13CH4 signature to distinguish between natural gas and landfills or ruminants. We present measurements of mobile field δ13CH4 using a spectroscopic stable isotope analyzer based on cavity ringdown spectroscopy, in three intense natural gas producing regions of the United States: the Denver-Julesburg basin in Colorado, the Uintah basin in Utah, and the Barnett Shale in Texas. Mobile isotope measurements of individual sources and in the nocturnal boundary layer have been combined to establish the fraction of the observed methane emissions that can be attributed to natural gas activities. The fraction of total methane emissions in the Denver-Julesburg basin attributed to natural gas emissions is 78 +/- 13%. In the Uinta basin, which has no other significant sources of methane, the fraction is 96% +/- 15%. In addition, results from the Barnett shale are presented, which includes a major urban center (Dallas / Ft. Worth). Methane emissions in this region are spatially highly heterogeneous. Spatially-resolved isotope and concentration measurements are interpreted using a simple emissions model to arrive at an overall isotope ratio for the region. (left panel) Distribution of oil and gas well pads (yellow) and landfills (blue) in the Dallas / Ft. Worth area. Mobile nocturnal measurements

Fugitive emission rates assessment of PM2.5 and PM10 from open storage piles in China

Science.gov (United States)

Cao, Yiqi; Liu, Tao; He, Jiao

2018-03-01

An assessment of the fugitive emission rates of PM2.5 and PM10 from an open static coal and mine storage piles. The experiment was conducted at a large union steel enterprises in the East China region to effectively control the fugitive particulate emissions pollution on daily work and extreme weather conditions. Wind tunnel experiments conducted on the surface of static storage piles, and it generated specific fugitive emission rates (SERs) at ground level of between ca.10-1 and ca.102 (mg/m2·s) for PM2.5 and between ca.101 and ca.103 (mg/m2·s) for PM10 under the u*(wind velocity) between ca.3.0 (m/s) and 10.0 (m/s). Research results show that SERs of different materials differ a lot. Material particulate that has lower surface moisture content generate higher SER and coal material generate higher SER than mine material. For material storage piles with good water infiltrating properties, aspersion is a very effective measure for control fugitive particulate emission.

38 CFR 3.666 - Incarcerated beneficiaries and fugitive felons-pension.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Incarcerated beneficiaries and fugitive felons-pension. 3.666 Section 3.666 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation...

Characterization of Dust Properties at the Source Region During ACE-Asia

Science.gov (United States)

Tsay, Si-Chee; Lau, William (Technical Monitor)

2001-01-01

ACE (Aerosol Characterization Experiment)-Asia is designed to study the compelling variability in spatial and temporal scale of both pollution-derived and naturally-occurring aerosols, which often exist in high concentrations over eastern Asia and along the rim of the western Pacific. The phase-I of ACE-Asia was conducted from March-May 2001 in the vicinity of the Gobi desert, east coast of China, Yellow Sea, Korea, and Japan, along the pathway of Kosa (severe events that blanket East Asia with yellow desert dust, peaked in the Spring season). Asian dust typically originates in desert areas far from polluted urban regions. During transport, dust layers can interact with anthropogenic sulfate and soot aerosols from heavily polluted urban areas. Added to the complex effects of clouds and natural marine aerosols, dust particles reaching the marine environment can have drastically different properties than those from the source. Thus, understanding the unique temporal and spatial variations of Asian dust is of special importance in regional-to-global climate issues such as radiative forcing, the hydrological cycle, and primary biological productivity in the mid-Pacific Ocean. During ACE-Asia we have measured continuously aerosol optical/radiative properties, column precipitable water amount, and surface reflectivity over homogeneous areas from surface. The inclusion of flux measurements permits the determination of dust aerosol radiative flux in addition to measurements of loading and optical thickness. At the time of the Terra/MODIS overpass, these ground-based observations can provide valuable data to compare with MODIS retrievals over land. Preliminary results will be presented and discussed their implications in regional climatic effects.

Identifying sources of respirable quartz and silica dust in underground coal mines in southern West Virginia, western Virginia, and eastern Kentucky

Energy Technology Data Exchange (ETDEWEB)

Schatzel, Steven J. [National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, 626 Cochrans Mill Road, PO Box 18070, Pittsburgh, PA 15236 (United States)

2009-04-01

Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers. (author)

Modeling the biogeochemical impact of atmospheric phosphate deposition from desert dust and combustion sources to the Mediterranean Sea

Science.gov (United States)

Richon, Camille; Dutay, Jean-Claude; Dulac, François; Wang, Rong; Balkanski, Yves

2018-04-01

Daily modeled fields of phosphate deposition to the Mediterranean from natural dust, anthropogenic combustion and wildfires were used to assess the effect of this external nutrient on marine biogeochemistry. The ocean model used is a high-resolution (1/12°) regional coupled dynamical-biogeochemical model of the Mediterranean Sea (NEMO-MED12/PISCES). The input fields of phosphorus are for 2005, which are the only available daily resolved deposition fields from the global atmospheric chemical transport model LMDz-INCA. Traditionally, dust has been suggested to be the main atmospheric source of phosphorus, but the LMDz-INCA model suggests that combustion is dominant over natural dust as an atmospheric source of phosphate (PO4, the bioavailable form of phosphorus in seawater) for the Mediterranean Sea. According to the atmospheric transport model, phosphate deposition from combustion (Pcomb) brings on average 40.5×10-6 mol PO4 m-2 yr-1 over the entire Mediterranean Sea for the year 2005 and is the primary source over the northern part (e.g., 101×10-6 mol PO4 m-2 yr-1 from combustion deposited in 2005 over the north Adriatic against 12.4×10-6 from dust). Lithogenic dust brings 17.2×10-6 mol PO4 m-2 yr-1 on average over the Mediterranean Sea in 2005 and is the primary source of atmospheric phosphate to the southern Mediterranean Basin in our simulations (e.g., 31.8×10-6 mol PO4 m-2 yr-1 from dust deposited in 2005 on average over the south Ionian basin against 12.4×10-6 from combustion). The evaluation of monthly averaged deposition flux variability of Pdust and Pcomb for the 1997-2012 period indicates that these conclusions may hold true for different years. We examine separately the two atmospheric phosphate sources and their respective flux variability and evaluate their impacts on marine surface biogeochemistry (phosphate concentration, chlorophyll a, primary production). The impacts of the different phosphate deposition sources on the biogeochemistry of the

Arabian Red Sea coastal soils as potential mineral dust sources

Directory of Open Access Journals (Sweden)

P. Jish Prakash

2016-09-01

Full Text Available Both Moderate Resolution Imaging Spectroradiometer (MODIS and Spinning Enhanced Visible and InfraRed Imager (SEVIRI satellite observations suggest that the narrow heterogeneous Red Sea coastal region is a frequent source of airborne dust that, because of its proximity, directly affects the Red Sea and coastal urban centers. The potential of soils to be suspended as airborne mineral dust depends largely on soil texture, moisture content and particle size distributions. Airborne dust inevitably carries the mineralogical and chemical signature of a parent soil. The existing soil databases are too coarse to resolve the small but important coastal region. The purpose of this study is to better characterize the mineralogical, chemical and physical properties of soils from the Arabian Red Sea coastal plain, which in turn will help to improve assessment of dust effects on the Red Sea, land environmental systems and urban centers. Thirteen surface soils from the hot-spot areas of windblown mineral dust along the Red Sea coastal plain were sampled for analysis. Analytical methods included optical microscopy, X-ray diffraction (XRD, inductively coupled plasma optical emission spectrometry (ICP-OES, ion chromatography (IC, scanning electron microscopy (SEM and laser particle size analysis (LPSA. We found that the Red Sea coastal soils contain major components of quartz and feldspar, as well as lesser but variable amounts of amphibole, pyroxene, carbonate, clays and micas, with traces of gypsum, halite, chlorite, epidote and oxides. The range of minerals in the soil samples was ascribed to the variety of igneous and metamorphic provenance rocks of the Arabian Shield forming the escarpment to the east of the Red Sea coastal plain. The analysis revealed that the samples contain compounds of nitrogen, phosphorus and iron that are essential nutrients to marine life. The analytical results from this study will provide a valuable input into dust emission models

Source identification of heavy metals in atmospheric dust using Platanus orientalis L. leaves as bioindicator

Directory of Open Access Journals (Sweden)

Samira Norouzi

2015-07-01

Full Text Available Studies on atmospheric dust have been limited by the high cost of instrumental monitoring methods and also sampling difficulties. The use of organisms acting as bioaccumulators has recently been proposed. In this study, the leaves of Platanus orientalis L., as a possible biomonitor of heavy metals in atmospheric dust, were evaluated to understand the likely source(s of pollution in Isfahan, Iran. Concentration of Zn, Cu, Ni and Mn and Magnetic susceptibility (χlf were determined in washed (WL and unwashed leaves (UL, monthly sampled from May to Nov., 2012. By subtracting the amount of metal concentrations and χlf in UL and WL, the amount of these parameters in dust deposited on the leaves (UL-WL were calculated. Enrichment factor analysis (EF, correlation coeficient, principal component analysis (PCA and cluster analysis (CA on the UL-WL data were employed to trace the heavy metals sources. Results showed that the metal concentration in UL and WL in primary sampling times was not statistically different. As time passed, this difference became more noticeable. Seasonal accumulation trends of elements concentration in UL-WL, referred to as accumulative biomonitors showing the accumulation of dust on the leaves are considerable and the contamination of plants by metal occurs mainly by retention of particulate matter. All the heavy metals are well correlated with χlf, indicating the potential of magnetic measurement as an inexpensive and less laborious method to estimate heavy metals. Cu and Zn exhibited a very strong correlation with each other and the highest correlation with χlf, suggesting an anthropogenic nature of these two metals. High EF of Cu and Zn showed that anthropogenic sources contribute a substantial amount of these metals to dust deposited on leaves. Whereas, less EF for Mn and Ni shows that natural source and local polluted soils might be the main origins of these metals. PCA results showed 2 principal components. Factor 1 with

A novel integrated approach for the hazardous radioactive dust source terms estimation in future nuclear fusion power plants.

Science.gov (United States)

Poggi, L A; Malizia, A; Ciparisse, J F; Gaudio, P

2016-10-01

An open issue still under investigation by several international entities working on the safety and security field for the foreseen nuclear fusion reactors is the estimation of source terms that are a hazard for the operators and public, and for the machine itself in terms of efficiency and integrity in case of severe accident scenarios. Source term estimation is a crucial key safety issue to be addressed in the future reactors safety assessments, and the estimates available at the time are not sufficiently satisfactory. The lack of neutronic data along with the insufficiently accurate methodologies used until now, calls for an integrated methodology for source term estimation that can provide predictions with an adequate accuracy. This work proposes a complete methodology to estimate dust source terms starting from a broad information gathering. The wide number of parameters that can influence dust source term production is reduced with statistical tools using a combination of screening, sensitivity analysis, and uncertainty analysis. Finally, a preliminary and simplified methodology for dust source term production prediction for future devices is presented.

A large source of dust missing in Particulate Matter emission inventories? Wind erosion of post-fire landscapes

Directory of Open Access Journals (Sweden)

N.S. Wagenbrenner

2017-02-01

Full Text Available Wind erosion of soils burned by wildfire contributes substantial particulate matter (PM in the form of dust to the atmosphere, but the magnitude of this dust source is largely unknown. It is important to accurately quantify dust emissions because they can impact human health, degrade visibility, exacerbate dust-on-snow issues (including snowmelt timing, snow chemistry, and avalanche danger, and affect ecological and biogeochemical cycles, precipitation regimes, and the Earth’s radiation budget. We used a novel modeling approach in which local-scale winds were used to drive a high-resolution dust emission model parameterized for burned soils to provide a first estimate of post-fire PM emissions. The dust emission model was parameterized with dust flux measurements from a 2010 fire scar. Here we present a case study to demonstrate the ability of the modeling framework to capture the onset and dynamics of a post-fire dust event and then use the modeling framework to estimate PM emissions from burn scars left by wildfires in U.S. western sagebrush landscapes during 2012. Modeled emissions from 1.2 million ha of burned soil totaled 32.1 Tg (11.7–352 Tg of dust as PM10 and 12.8 Tg (4.68–141 Tg as PM2.5. Despite the relatively large uncertainties in these estimates and a number of underlying assumptions, these first estimates of annual post-fire dust emissions suggest that post-fire PM emissions could substantially increase current annual PM estimates in the U.S. National Emissions Inventory during high fire activity years. Given the potential for post-fire scars to be a large source of PM, further on-site PM flux measurements are needed to improve emission parameterizations and constrain these first estimates.

Quantifying the relative contribution of natural gas fugitive emissions to total methane emissions in Weld County Colorado using δ13CH4 analysis

Science.gov (United States)

Rella, C.; Jacobson, G. A.; Crosson, E.; Sweeney, C.; Karion, A.; Petron, G.

2012-12-01

Fugitive emissions of methane into the atmosphere are a major concern facing the natural gas production industry. Given that the global warming potential of methane is many times greater than that of carbon dioxide (Forster et al. 2007), the importance of quantifying methane emissions becomes clear. Companion presentations at this meeting describe efforts to quantify the overall methane emissions in two separate gas producing areas in Colorado and Utah during intensive field campaigns undertaken in 2012. A key step in the process of assessing the emissions arising from natural gas production activities is partitioning the observed methane emissions between natural gas fugitive emissions and other sources of methane, such as from landfills or agricultural activities. One method for assessing the contribution of these different sources is stable isotope analysis. In particular, the δ13CH4 signature of natural gas (-37 permil) is significantly different that the signature of other significant sources of methane, such as landfills or ruminants (-50 to -70 permil). In this paper we present measurements of δ13CH4 in Colorado in Weld County, a region of intense natural gas production, using a mobile δ13CH4¬ analyzer capable of high-precision measurements of the stable isotope ratio of methane at ambient levels. This analyzer was used to make stable isotope measurements at a fixed location near the center of the gas producing region, from which an overall isotope ratio for the regional emissions is determined. In addition, mobile measurements in the nocturnal boundary layer have been made, over a total distance of 150 km throughout Weld County, allowing spatially resolved measurements of this isotope signature. Finally, this analyzer was used to quantify the isotopic signature of those individual sources (natural gas fugitive emissions, concentrated animal feeding operations, and landfills) that constitute the majority of methane emissions in this region, by making

Spatial distribution, environmental risk and source of heavy metals in street dust from an industrial city in semi-arid area of China

Directory of Open Access Journals (Sweden)

Han Xiufeng

2017-06-01

Full Text Available Environmental risks associated with Co, Cr, Cu, Mn, Ni, Pb, V and Zn in street dust collected from Baotou, a medium-sized industrial city in a semi-arid area of northwest China, were assessed by using enrichment factor and the potential ecological index. Their spatial distributions and sources in the dust were analyzed on the basis of geostatistical methods and multivariate statistical analysis, respectively. The results indicate that street dust in Baotou has elevated heavy metal concentrations, especially of Co, Cr, Cu, Pb and Zn. Co in the dust was significantly enriched. Cr and Pb were from moderate to significant enrichment. Cu and Zn were from minimal to moderate enrichment, whereas Mn, Ni and V in the dust were from deficient to minimal enrichment. The ecological risk levels of Co and Pb in the dust were moderate to considerable and low to moderate, respectively, whereas those of other heavy metals studied in the dust presented low ecological risk. Different distribution patterns were found among the analyzed heavy metals. Three main sources of these heavy metals were identified. Cr, Mn, Ni and V originated from nature and industrial activities. Cu, Pb and Zn derived mainly from traffic sources, and Co was mainly from construction sources.

Evaluation of dust and trace metal estimates from the Community Multiscale Air Quality (CMAQ model version 5.0

Directory of Open Access Journals (Sweden)

K. W. Appel

2013-07-01

trace metals. Removing the anthropogenic fugitive dust (AFD emissions and the effects of wind-blown dust (WBD lowered the model soil concentrations. However, even with both AFD emissions and WBD effects removed, soil concentrations were still often overestimated, suggesting that there are other sources of errors in the modeling system that contribute to the overestimation of soil components. Efforts are underway to improve both the nighttime mixing in urban areas and the spatial and temporal distribution of dust-related emission sources in the emissions inventory.

Lead and other elements in house dust of Japanese residences – Source of lead and health risks due to metal exposure

International Nuclear Information System (INIS)

Yoshinaga, Jun; Yamasaki, Kumiko; Yonemura, Ayumi; Ishibashi, Yuri; Kaido, Takaya; Mizuno, Kodai; Takagi, Mai; Tanaka, Atsushi

2014-01-01

The levels of 25 elements in house dust collected from 100 general Japanese residences were measured. Factor analysis was applied on the multi-element data to explore source of Pb (median concentration 49.1 mg/kg) in house dust. Six factors were extracted and Pb was found to have great loading on the fifth factor with Sb and Sn, suggesting solder (Sn), and plastic and metals (Sb) may be the sources of Pb in the house dust of Japanese residences. No significant loading was found on soil-related factors indicating non-significant contribution of Pb in track-in soil. Seven heavy metals (Cd, Cu, Mo, Pb, Sb, Sn, and Zn) were found in house dust at >10 times more condensed than crustal abundance. Health risk of these elements to children via the ingestion of house dust was estimated based on the comparison with tolerable daily intake and found to be non-significant for most of the elements. - Highlights: • Multi-element analysis was carried out for house dust from households in Japan. • Factor analysis was applied on the multivariate data set. • The abundance of lead had a close relationship with antimony and tin in house dust. • Health risk of heavy metals in house dust for children was not serious. - Major source of Pb in house dust of Japanese residences was not track-in soil but unknown materials that contain Pb and Sb and/or Sn

Quantifying the relative contribution of natural gas fugitive emissions to total methane emissions in Colorado, Utah, and Texas using mobile isotopic methane analysis based on Cavity Ringdown Spectroscopy

Science.gov (United States)

Rella, Chris; Winkler, Renato; Sweeney, Colm; Karion, Anna; Petron, Gabrielle; Crosson, Eric

2014-05-01

Fugitive emissions of methane into the atmosphere are a major concern facing the natural gas production industry. Because methane is more energy-rich than coal per kg of carbon dioxide emitted into the atmosphere, it represents an attractive alternative to coal for electricity generation, provided that the fugitive emissions of methane are kept under control. A key step in assessing these emissions in a given region is partitioning the observed methane emissions between natural gas fugitive emissions and other sources of methane, such as from landfills or agricultural activities. One effective method for assessing the contribution of these different sources is stable isotope analysis, using the isotopic carbon signature to distinguish between natural gas and landfills or ruminants. We present measurements of methane using a mobile spectroscopic stable isotope analyzer based on cavity ringdown spectroscopy, in three intense natural gas producing regions of the United States: the Denver-Julesburg basin in Colorado, the Uintah basin in Utah, and the Barnett Shale in Texas. Performance of the CRDS isotope analyzer is presented, including precision, calibration, stability, and the potential for measurement bias due to other atmospheric constituents. Mobile isotope measurements of individual sources and in the nocturnal boundary layer have been combined to establish the fraction of the observed methane emissions that can be attributed to natural gas activities. The fraction of total methane emissions in the Denver-Julesburg basin attributed to natural gas emissions is 78 +/- 13%. In the Uinta basin, which has no other significant sources of methane, the fraction is 96% +/- 15%. In addition, results from the Barnett shale are presented, which includes a major urban center (Dallas / Ft. Worth). Methane emissions in this region are spatially highly heterogeneous. Spatially-resolved isotope and concentration measurements are interpreted using a simple emissions model to

Probing the Spatial Distribution of the Interstellar Dust Medium by High Angular Resolution X-ray Halos of Point Sources

Science.gov (United States)

Xiang, Jingen

X-rays are absorbed and scattered by dust grains when they travel through the interstellar medium. The scattering within small angles results in an X-ray ``halo''. The halo properties are significantly affected by the energy of radiation, the optical depth of the scattering, the grain size distributions and compositions, and the spatial distribution of dust along the line of sight (LOS). Therefore analyzing the X-ray halo properties is an important tool to study the size distribution and spatial distribution of interstellar grains, which plays a central role in the astrophysical study of the interstellar medium, such as the thermodynamics and chemistry of the gas and the dynamics of star formation. With excellent angular resolution, good energy resolution and broad energy band, the Chandra ACIS is so far the best instrument for studying the X-ray halos. But the direct images of bright sources obtained with ACIS usually suffer from severe pileup which prevents us from obtaining the halos in small angles. We first improve the method proposed by Yao et al to resolve the X-ray dust scattering halos of point sources from the zeroth order data in CC-mode or the first order data in TE mode with Chandra HETG/ACIS. Using this method we re-analyze the Cygnus X-1 data observed with Chandra. Then we studied the X-ray dust scattering halos around 17 bright X-ray point sources using Chandra data. All sources were observed with the HETG/ACIS in CC-mode or TE-mode. Using the interstellar grain models of WD01 model and MRN model to fit the halo profiles, we get the hydrogen column densities and the spatial distributions of the scattering dust grains along the line of sights (LOS) to these sources. We find there is a good linear correlation not only between the scattering hydrogen column density from WD01 model and the one from MRN model, but also between N_{H} derived from spectral fits and the one derived from the grain models WD01 and MRN (except for GX 301-2 and Vela X-1): N

Anthropogenic Air Pollution Observed Near Dust Source Regions in Northwestern China During Springtime 2008

Science.gov (United States)

Li, Can; Tsay, Si-Chee; Fu, Joshua S.; Dickerson, Russell R.; Ji, Qiang; Bell, Shaun W.; Gao, Yang; Zhang, Wu; Huang, Jianping; Li, Zhanqing;

Study of characterizations of aerosols in a dust storm source region and its influence on Beijing by NAA and ICP-MS

International Nuclear Information System (INIS)

Song Yan; Chai Zhifang; Xu Diandou; Feng Weiyue; Ouyang Hong; Mao Xueying

2005-01-01

Dust storms have caused many problems in the environment, health and climate. For decades, dust storms have occurred frequently in various regions of China. The dust aerosols not only affected the local atmosphere, but also contaminated the atmosphere of the circumjacent regions. Further, they could affect Korea, Japan and even USA via long-range transportation. Many researches related to Chinese dust storms have been reported, however, there are few reports on the chemical components and characters of dust aerosols at their sources. Data on chemical properties of dust storm in the dust source region can help people understand the characteristics of dust storms and their influence on local and other regions. Duolun county (42 degree 13' N, 116 degree 25' E) lies in the southeast of Inner Mongolia, China, in the south of Hunshandake sands (one of the four famous sands in China). Because it is located at windward of Beijing, the dust aerosols can affect Beijing quickly when dust storm occurs. Hence, the study of chemical compositions and elemental abundance patterns of atmospheric particulate matters at Duolun is imperative to understand its influence on Beijing's atmospheric quality. In this work, TSP and PM2.5 samples were collected in Beijing and Duolun, Inner Mongolia, China, in April and May of 2002. Monthly arithmetic averages of the mass concentrations indicated that the pollution of atmospheric particulate matter's (APM) in Duolun was very serious, especially in April. The chemical compositions of total 163 samples were analyzed by INAA and ICP-MS and their origins were identified through Enrichment Factor and Principal Component Analysis. The results showed that the main source of Duolun aerosols was soil dust, and coal combustion constituted the important anthropogenic contribution. The dust events in April and changes of local meteorological conditions were the main reasons for the differences of APM characteristics between April and May. The

Advancing Knowledge on Fugitive Natural Gas from Energy Resource Development at a Controlled Release Field Observatory

Science.gov (United States)

Cahill, A. G.; Chao, J.; Forde, O.; Prystupa, E.; Mayer, K. U.; Black, T. A.; Tannant, D. D.; Crowe, S.; Hallam, S.; Mayer, B.; Lauer, R. M.; van Geloven, C.; Welch, L. A.; Salas, C.; Levson, V.; Risk, D. A.; Beckie, R. D.

2017-12-01

Fugitive gas, comprised primarily of methane, can be unintentionally released from upstream oil and gas development either at surface from leaky infrastructure or in the subsurface through failure of energy well bore integrity. For the latter, defective cement seals around energy well casings may permit buoyant flow of natural gas from the deeper subsurface towards shallow aquifers, the ground surface and potentially into the atmosphere. Concerns associated with fugitive gas release at surface and in the subsurface include contributions to greenhouse gas emissions, subsurface migration leading to accumulation in nearby infrastructure and impacts to groundwater quality. Current knowledge of the extent of fugitive gas leakage including how to best detect and monitor over time, and particularly its migration and fate in the subsurface, is incomplete. We have established an experimental field observatory for evaluating fugitive gas leakage in an area of historic and ongoing hydrocarbon resource development within the Montney Resource Play of the Western Canadian Sedimentary Basin, British Columbia, Canada. Natural gas will be intentionally released at surface and up to 25 m below surface at various rates and durations. Resulting migration patterns and impacts will be evaluated through examination of the geology, hydrogeology, hydro-geochemistry, isotope geochemistry, hydro-geophysics, vadose zone and soil gas processes, microbiology, and atmospheric conditions. The use of unmanned aerial vehicles and remote sensors for monitoring and detection of methane will also be assessed for suitability as environmental monitoring tools. Here we outline the experimental design and describe initial research conducted to develop a detailed site conceptual model of the field observatory. Subsequently, results attained from pilot surface and sub-surface controlled natural gas releases conducted in late summer 2017 will be presented as well as results of numerical modelling conducted

Elucidating the urban levels, sources and health risks of polycyclic aromatic hydrocarbons (PAHs) in Pakistan: Implications for changing energy demand.

Science.gov (United States)

Hamid, Naima; Syed, Jabir Hussain; Junaid, Muhammad; Mahmood, Adeel; Li, Jun; Zhang, Gan; Malik, Riffat Naseem

2018-04-01

Due to the severe fuel crisis in terms of natural gas, a paradigm shift in fuel combustion (diesel, gasoline, and biomass) may increase the atmospheric emissions and associated health risks in Pakistan. Present study was aimed to investigate the concentration of fugitive PAHs in the environment (outdoor and indoor settings), associated probabilistic health risk assessment in the exposed population, and possible linkage between fuel consumption patterns and PAHs emissions in twin cities (Rawalpindi and Islamabad) of Pakistan. Results showed that the mean PAHs concentrations (air: 2390pgm -3 ; dust: 167ngg -1 ) in the indoor environment were higher than that of the outdoor environment (air: 2132pgm -3 ; dust: 90.0ngg -1 ). Further, the source apportionment PCA-MLR receptor model identified diesel and gasoline combustion as the primary PAHs sources in the urban and sub-urban settings. Estimated life cancer risk (LCR) potential via inhalation to indoor PAHs was higher with a probability of 2.0 cases per 10,000 inhabitants as compared to outdoor exposure. Incremental lifetime cancer risk (ILCR) model from exposure to dust bound PAHs showed risk in the order of ingestion>dermal>inhalation for various exposure pathways. Likewise, estimated daily intake (EDI) model reflects that PAHs in surface dust enter into the human body mainly through the respiratory system because EDI for breathing was reported higher than that of oral intake. Therefore, adoption of sustainable fuels is recommended to meet the energy requirements and to reduce PAHs emissions and related health risks in the twin cities of Pakistan. Copyright © 2017 Elsevier B.V. All rights reserved.

Novel plasma source for safe beryllium spectral line studies in the presence of beryllium dust

Science.gov (United States)

Stankov, B. D.; Vinić, M.; Gavrilović Božović, M. R.; Ivković, M.

2018-05-01

Plasma source for beryllium spectral line studies in the presence of beryllium dust particles was realised. The guideline during construction was to prevent exposure to formed dust, considering the toxicity of beryllium. Plasma source characterization through determination of optimal working conditions is described. The necessary conditions for Be spectral line appearance and optimal conditions for line shape measurements are found. It is proven experimentally that under these conditions dust appears coincidently with the second current maximum. The electron density measured after discharge current maximum is determined from the peak separation of the hydrogen Balmer beta spectral line, and the electron temperature is determined from the ratios of the relative intensities of Be spectral lines emitted from successive ionized stages of atoms. Maximum values of electron density and temperature are measured to be 9.3 × 1022 m-3 and 16 800 K, respectively. Construction details and testing of the BeO discharge tube in comparison with SiO2 and Al2O3 discharge tubes are also presented in this paper.

Salt Efflorescence Effects on Soil Surface Erodibility and Dust Emissions

Science.gov (United States)

Van Pelt, R. S.; Zhang, G.

2017-12-01

Soluble salts resulting from weathering of geological materials often form surface crusts or efflorescences in areas with shallow saline groundwater. In many cases, the affected areas are susceptible to wind erosion due to their lack of protective vegetation and their flat topography. Fugitive dusts containing soluble salts affect the biogeochemistry of deposition regions and may result in respiratory irritation during transport. We created efflorescent crusts on soil trays by surface evaporation of single salt solutions and bombarded the resultant efflorescences with quartz abrader sand in a laboratory wind tunnel. Four replicate trays containing a Torrifluvent soil affected by one of nine salts commonly found in arid and semiarid streams were tested and the emissions were captured by an aspirated multi-stage deposition and filtering system. We found that in most cases the efflorescent crust reduced the soil surface erodibility but also resulted in the emission of salt rich dust. Two of the salts, sodium thiosulfate and calcium chloride, resulted in increased soil volume and erodibility. However, one of the calcium chloride replicates was tested after an outbreak of humid air caused hygroscopic wetting of the soil and it became indurated upon drying greatly decreasing the erodibility. Although saline affected soils are not used for agricultural production and degradation is not a great concern, the release of salt rich dust is an area of environmental concern and steps to control the dust emissions from affected soils should be developed. Future testing will utilize suites of salts found in streams of arid and semiarid regions.

40 CFR 63.7292 - What work practice standards must I meet for fugitive pushing emissions if I have a by-product...

Science.gov (United States)

2010-07-01

... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? 63... meet for fugitive pushing emissions if I have a by-product coke oven battery with horizontal flues? (a...) Prepare and operate by a written plan that will eliminate or minimize incomplete coking for each by...

Short-term variability of mineral dust, metals and carbon emission from road dust resuspension

Science.gov (United States)

Amato, Fulvio; Schaap, Martijn; Denier van der Gon, Hugo A. C.; Pandolfi, Marco; Alastuey, Andrés; Keuken, Menno; Querol, Xavier

2013-08-01

Particulate matter (PM) pollution in cities has severe impact on morbidity and mortality of their population. In these cities, road dust resuspension contributes largely to PM and airborne heavy metals concentrations. However, the short-term variation of emission through resuspension is not well described in the air quality models, hampering a reliable description of air pollution and related health effects. In this study we experimentally show that the emission strength of resuspension varies widely among road dust components/sources. Our results offer the first experimental evidence of different emission rates for mineral dust, heavy metals and carbon fractions due to traffic-induced resuspension. Also, the same component (or source) recovers differently in a road in Barcelona (Spain) and a road in Utrecht (The Netherlands). This finding has important implications on atmospheric pollution modelling, mostly for mineral dust, heavy metals and carbon species. After rain events, recoveries were generally faster in Barcelona rather than in Utrecht. The largest difference was found for the mineral dust (Al, Si, Ca). Tyre wear particles (organic carbon and zinc) recovered faster than other road dust particles in both cities. The source apportionment of road dust mass provides useful information for air quality management.

Emissions of road dust by winter tyres and the contributions of different road dust sources in road side particle samples; Talvirenkaiden poelypaeaestoet ja eri katupoelylaehteiden osuudet kadunvarrella keraetyissae hiukkasnaeytteissae

Energy Technology Data Exchange (ETDEWEB)

Kupiainen, K.; Pirjola, L.; Ritola, R.; Stojiljkovic, A.; Malinen, A.

2013-09-01

Aim of this study was to determine: (1) the relative contributions from pavement wear and traction sanding in PM{sub 10} road side air and road dust resuspension samples; (2) PM{sub 10} dust emissions from studded and studless tyres in on-road conditions. The study was conducted as part of the NASTA research program during the winter season 2011/2012. The studies were carried out in Suurmetsaentie and Viikintie in Helsinki, Finland. The results showed that dust from pavement aggregates was the largest source during spring, accounting for 40- 50 percent of the particulate matter in the air and resuspension samples. Based on studies on formation of dust, major source of the dust from pavement aggregates is the wear by studded tyres. Traction sand and road salt were used frequently during the winter 2011/2012. Sanding material explained about 25 percent of the road dust in the air and resuspension samples. Traction sanding is estimated to account for approximately few percent of the pavement dust via the sandpaper effect. Effect of road salt was few percent in the samples. The source contributions from pavement and traction sanding observed in spring 2011/2012 at Suurmetsaentie are similar to what has been estimated in previous studies conducted in the early 2000s in Finland. In a study conducted in the city of Hanko, it was estimated the contribution from traction sanding to be in average of about 10 percent. In another study in the center of Helsinki the contribution was estimated to be about half of the PM{sub 10}. The general perception in Finland has been that traction sanding is the main source of airborne road dust. Studies conducted in 2000s and the results of this study, however, indicate that traction sanding has been an important but not the main source of PM10 road dust even in winters with extensive use of gravel for traction control. Emissions of road dust by a single tyre consist of direct emissions of wear products as well as resuspension emissions of

40 CFR 63.1459 - What definitions apply to this subpart?

Science.gov (United States)

2010-07-01

... Clean Air Act, in § 63.2, and in this section as follows: Bag leak detection system means a system that... from one or more emission points, and to convey the captured gases and fumes to a control device. A..., storage, transfer, or other management of fugitive dust materials where the source is not associated with...

The impact of seasonal varied human activity on characteristics and sources of heavy metals in metropolitan road dusts.

Science.gov (United States)

Men, Cong; Liu, Ruimin; Wang, Qingrui; Guo, Lijia; Shen, Zhenyao

2018-10-01

Due to significant human activity, road dust is becoming contaminated by heavy metals in many cities. To comprehensively investigate the variation of contamination level and sources of heavy metals in road dust, 10 heavy metals in road dust samples from Beijing, China, in both summer and winter, were evaluated by spatial analysis using geographic information system (GIS) mapping technology and the positive matrix factorization (PMF) Model. Although the concentrations of some heavy metals between summer and winter had similarities, the differences of others and spatial distributions of heavy metals between summer and winter were considerable. The mean concentrations of As, Cd, Cr, Cu, and Fe were lower in winter, while those of Hg, Mn, Ni, Pb, and Zn were higher. According to the values of the Pollution Index (PI) and Nemerow Integrated Pollution Index (NIPI), there were no obvious differences between summer and winter, but the range between different sites in winter was nearly twice that of summer. Based on the PMF model, four sources of heavy metals in the dust samples were identified. Although the types of sources were consistent, the relative contributions of each source differed between summer and winter. Non-exhaust vehicle emissions was the most important source in summer (34.47 wt%), while fuel combustion contributed the largest proportion to the total heavy metals in winter (32.40 wt%). The impact of each source also showed spatial variation different trends in summer and winter. With the alteration of seasons, intensity of human activities also changed, such as the number of tourists, energy needs for building temperature regulation, construction, and the amount of pesticides and fertilizer. That might be the reason for the variation of heavy metal concentrations and relative contribution of their sources between summer and winter. Copyright © 2018 Elsevier B.V. All rights reserved.

Palaeo-dust records: A window to understanding past environments

Science.gov (United States)

Marx, Samuel K.; Kamber, Balz S.; McGowan, Hamish A.; Petherick, Lynda M.; McTainsh, Grant H.; Stromsoe, Nicola; Hooper, James N.; May, Jan-Hendrik

2018-06-01

Dust entrainment, transport over vast distances and subsequent deposition is a fundamental part of the Earth system. Yet the role and importance of dust has been underappreciated, due largely to challenges associated with recognising dust in the landscape and interpreting its depositional history. Despite these challenges, interest in dust is growing. Technical advances in remote sensing and modelling have improved understanding of dust sources and production, while advances in sedimentology, mineralogy and geochemistry (in particular) have allowed dust to be more easily distinguished within sedimentary deposits. This has facilitated the reconstruction of records of dust emissions through time. A key advance in our understanding of dust has occurred following the development of methods to geochemically provenance (fingerprint) dust to its source region. This ability has provided new information on dust transport pathways, as well as the reach and impact of dust. It has also expanded our understanding of the processes driving dust emissions over decadal to millennial timescales through linking dust deposits directly to source area conditions. Dust provenance studies have shown that dust emission, transport and deposition are highly sensitive to variability in climate. They also imply that dust emissions are not simply a function of the degree of aridity in source areas, but respond to a more complex array of conditions, including sediment availability. As well as recording natural variability, dust records are also shown to sensitively track the impact of human activity. This is reflected by both changing dust emission rates and changing dust chemistry. Specific examples of how dust responds to, and records change, are provided with our work on dust emissions from Australia, the most arid inhabited continent and the largest dust source in the Southern Hemisphere. These case studies show that Australian dust emissions reflect hydro-climate variability, with

The global distribution of mineral dust

International Nuclear Information System (INIS)

Tegen, I; Schepanski, K

2009-01-01

Dust aerosol particles produced by wind erosion in arid and semi arid regions affect climate and air quality, but the magnitude of these effects is largely unquantified. The major dust source regions include the Sahara, the Arabian and Asian deserts; global annual dust emissions are currently estimated to range between 1000 and 3000 Mt/yr. Dust aerosol can be transported over long distances of thousands of kilometers, e.g. from source regions in the Saharan desert over the North Atlantic, or from the Asian deserts towards the Pacific Ocean. The atmospheric dust load varies considerably on different timescales. While dust aerosol distribution and dust effects are important on global scales, they strongly depend on dust emissions that are controlled on small spatial and temporal scales.

Dust Aerosols at the Source Region During ACE-ASIA: A Surface/Satellite Perspective

Science.gov (United States)

Tsay, Si-Chee; Lau, William K. M. (Technical Monitor)

2001-01-01

ACE (Aerosol Characterization Experiment)-Asia is designed to study the compelling variability in spatial and temporal scale of both pollution-derived and naturally occurring aerosols, which often exist in high concentrations over eastern Asia and along the rim of the western Pacific. The phase-I of ACE-Asia was conducted from March-May 2001 in the vicinity of the Gobi desert, East Coast of China, Yellow Sea, Korea, and Japan, along the pathway of Kosa (severe events that blanket East Asia with yellow desert dust, peaked in the Spring season). Asian dust typically originates in desert areas far from polluted urban regions. During transport, dust layers can interact with anthropogenic sulfate and soot aerosols from heavily polluted urban areas. Added to the complex effects of clouds and natural marine aerosols, dust particles reaching the marine environment can have drastically different properties than those from the source. Thus, understanding the unique temporal and spatial variations of Asian dust is of special importance in regional-to-global climate issues such as radiative forcing, the hydrological cycle, and primary biological productivity in the mid-Pacific Ocean. During ACE-Asia we have measured continuously aerosol physical/optical/radiative properties, column precipitable water amount, and surface reflectivity over homogeneous areas from surface. The inclusion of flux measurements permits the determination of dust aerosol radiative flux in addition to measurements of loading and optical thickness. At the time of the Terra/MODIS, SeaWiFS, TOMS and other satellite overpasses, these ground-based observations can provide valuable data to compare with satellite retrievals over land. Preliminary results will be presented and discussed their implications in regional climatic effects.

Size-resolved dust and aerosol contaminants associated with copper and lead smelting emissions: Implications for emission management and human health

Energy Technology Data Exchange (ETDEWEB)

Csavina, Janae [Department of Chemical and Environmental Engineering, The University of Arizona, Tucson, AZ 85721 (United States); Taylor, Mark P. [Environmental Science, Faculty of Science, Macquarie University, North Ryde, Sydney, NSW 2109 (Australia); Félix, Omar [Department of Chemical and Environmental Engineering, The University of Arizona, Tucson, AZ 85721 (United States); Rine, Kyle P. [Department of Atmospheric Sciences, The University of Arizona, Tucson, AZ 85721 (United States); Eduardo Sáez, A., E-mail: esaez@email.arizona.edu [Department of Chemical and Environmental Engineering, The University of Arizona, Tucson, AZ 85721 (United States); Betterton, Eric A., E-mail: betterton@atmo.arizona.edu [Department of Atmospheric Sciences, The University of Arizona, Tucson, AZ 85721 (United States)

2014-09-15

Mining operations, including crushing, grinding, smelting, refining, and tailings management, are a significant source of airborne metal and metalloid contaminants such as As, Pb and other potentially toxic elements. In this work, we show that size-resolved concentrations of As and Pb generally follow a bimodal distribution with the majority of contaminants in the fine size fraction (< 1 μm) around mining activities that include smelting operations at various sites in Australia and Arizona. This evidence suggests that contaminated fine particles (< 1 μm) are the result of vapor condensation and coagulation from smelting operations while coarse particles are most likely the result of windblown dust from contaminated mine tailings and fugitive emissions from crushing and grinding activities. These results on the size distribution of contaminants around mining operations are reported to demonstrate the ubiquitous nature of this phenomenon so that more effective emission management and practices that minimize health risks associated with metal extraction and processing can be developed. - Highlights: • Lead and copper smelting produce significant atmospheric concentrations of lead and arsenic. • Atmospheric lead and arsenic concentrations depend on particle size. • Lead isotopic analysis can be used to assess source of atmospheric contamination from smelters.

Mineral Dust Instantaneous Radiative Forcing in the Arctic

Science.gov (United States)

Kylling, A.; Groot Zwaaftink, C. D.; Stohl, A.

2018-05-01

Mineral dust sources at high and low latitudes contribute to atmospheric dust loads and dust deposition in the Arctic. With dust load estimates from Groot Zwaaftink et al. (https://doi.org/10.1002/2016JD025482), we quantify the mineral dust instantaneous radiative forcing (IRF) in the Arctic for the year 2012. The annual-mean top of the atmosphere IRF is 0.225 W/m2, with the largest contributions from dust transported from Asia south of 60°N and Africa. High-latitude (>60°N) dust sources contribute about 39% to top of the atmosphere IRF and have a larger impact (1 to 2 orders of magnitude) on IRF per emitted kilogram of dust than low-latitude sources. Mineral dust deposited on snow accounts for nearly all of the bottom of the atmosphere IRF of 0.135 W/m2. More than half of the bottom of the atmosphere IRF is caused by dust from high-latitude sources, indicating substantial regional climate impacts rarely accounted for in current climate models.

Study of Arabian Red Sea coastal soils as potential mineral dust sources

KAUST Repository

Prakash, P. Jish; Stenchikov, Georgiy L.; Tao, Weichun; Yapici, Tahir; Warsama, Bashir H.; Engelbrecht, Johann

2016-01-01

Both Moderate Resolution Imaging Spectroradiometer (MODIS) and Spinning Enhanced Visible and InfraRed Imager (SEVIRI) satellite observations suggest that the narrow heterogeneous Red Sea coastal region is a frequent source of airborne dust that, because of its proximity, directly affects the Red Sea and coastal urban centers. The potential of soils to be suspended as airborne mineral dust depends largely on soil texture, moisture content, and particle size distributions. Airborne dust inevitably carries the mineralogical and chemical signature of a parent soil. The existing soil databases are too coarse to resolve the small but important coastal region. The purpose of this study is to better characterize the mineralogical, chemical and physical properties of soils from the Red Sea Arabian coastal plane, which in turn will help to improve assessment of dust effect on the Red Sea and land environmental systems and urban centers. Thirteen surface soils from the hot-spot areas of wind-blown mineral dust along the Red Sea coastal plain were sampled for analysis. Analytical methods included Optical Microscopy, X-ray diffraction (XRD), Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES), Ion Chromatography (IC), Scanning Electron Microscopy (SEM), and Laser Particle Size Analysis (LPSA). We found that the Red Sea coastal soils contain major components of quartz and feldspar, as well as lesser but variable amounts of amphibole, pyroxene, carbonate, clays, and micas, with traces of gypsum, halite, chlorite, epidote and oxides. The wide range of minerals in the soil samples was ascribed to the variety of igneous and metamorphic provenance rocks of the Arabian Shield forming the escarpment to the east of the Red Sea coastal plain. The analysis revealed that the samples contain compounds of nitrogen, phosphorus and iron that are essential nutrients to marine life. The analytical results from this study will provide a valuable input into dust emission models used

Study of Arabian Red Sea coastal soils as potential mineral dust sources

KAUST Repository

Prakash, P. Jish

2016-03-23

Both Moderate Resolution Imaging Spectroradiometer (MODIS) and Spinning Enhanced Visible and InfraRed Imager (SEVIRI) satellite observations suggest that the narrow heterogeneous Red Sea coastal region is a frequent source of airborne dust that, because of its proximity, directly affects the Red Sea and coastal urban centers. The potential of soils to be suspended as airborne mineral dust depends largely on soil texture, moisture content, and particle size distributions. Airborne dust inevitably carries the mineralogical and chemical signature of a parent soil. The existing soil databases are too coarse to resolve the small but important coastal region. The purpose of this study is to better characterize the mineralogical, chemical and physical properties of soils from the Red Sea Arabian coastal plane, which in turn will help to improve assessment of dust effect on the Red Sea and land environmental systems and urban centers. Thirteen surface soils from the hot-spot areas of wind-blown mineral dust along the Red Sea coastal plain were sampled for analysis. Analytical methods included Optical Microscopy, X-ray diffraction (XRD), Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES), Ion Chromatography (IC), Scanning Electron Microscopy (SEM), and Laser Particle Size Analysis (LPSA). We found that the Red Sea coastal soils contain major components of quartz and feldspar, as well as lesser but variable amounts of amphibole, pyroxene, carbonate, clays, and micas, with traces of gypsum, halite, chlorite, epidote and oxides. The wide range of minerals in the soil samples was ascribed to the variety of igneous and metamorphic provenance rocks of the Arabian Shield forming the escarpment to the east of the Red Sea coastal plain. The analysis revealed that the samples contain compounds of nitrogen, phosphorus and iron that are essential nutrients to marine life. The analytical results from this study will provide a valuable input into dust emission models used

Rebuilding conveyor transfer points to cut fugitive material and improve operations

Energy Technology Data Exchange (ETDEWEB)

Stahura, R P [Martin Engineering Company, Neponset, MA (USA)

1992-10-01

The article describes a three-part programme to control spillage and prevent fugitive material at conveyor transfer points. The three parts are: adequate belt support; the installation of a wear line inside the chute to preserve the rubber seal system; and the maintenance of an effective edge seal. The article also discusses designing for ease of maintenance. 9 figs.

77 FR 73322 - Revisions to the California State Implementation Plan, Monterey Bay Unified Air Pollution Control...

Science.gov (United States)

2012-12-10

...EPA is taking direct final action to approve revisions to the Monterey Bay Unified Air Pollution Control District (MBUAPCD) portion of the California State Implementation Plan (SIP). These revisions concern opacity standards related to multiple pollutants, including particulate matter (PM) emissions from several different types of sources, ranging from fugitive dust to gas turbines. We are approving a local rule that regulates these emission sources under the Clean Air Act (CAA or the Act).

77 FR 73392 - Revisions to the California State Implementation Plan, Monterey Bay Unified Air Pollution Control...

Science.gov (United States)

2012-12-10

...EPA is proposing to approve revisions to the Monterey Bay Unified Air Pollution Control District (MBUAPCD) portion of the California State Implementation Plan (SIP). This revision concerns opacity standards related to multiple pollutants, including particulate matter (PM) emissions from several different types of sources, ranging from fugitive dust to gas turbines. We are proposing to approve a local rule to regulate these emission sources under the Clean Air Act (CAA or the Act).

Source influence on emission pathways and ambient PM2.5 pollution over India (2015-2050)

Science.gov (United States)

Venkataraman, Chandra; Brauer, Michael; Tibrewal, Kushal; Sadavarte, Pankaj; Ma, Qiao; Cohen, Aaron; Chaliyakunnel, Sreelekha; Frostad, Joseph; Klimont, Zbigniew; Martin, Randall V.; Millet, Dylan B.; Philip, Sajeev; Walker, Katherine; Wang, Shuxiao

2018-06-01

India is currently experiencing degraded air quality, and future economic development will lead to challenges for air quality management. Scenarios of sectoral emissions of fine particulate matter and its precursors were developed and evaluated for 2015-2050, under specific pathways of diffusion of cleaner and more energy-efficient technologies. The impacts of individual source sectors on PM2.5 concentrations were assessed through systematic simulations of spatially and temporally resolved particulate matter concentrations, using the GEOS-Chem model, followed by population-weighted aggregation to national and state levels. We find that PM2.5 pollution is a pan-India problem, with a regional character, and is not limited to urban areas or megacities. Under present-day emissions, levels in most states exceeded the national PM2.5 annual standard (40 µg m-3). Sources related to human activities were responsible for the largest proportion of the present-day population exposure to PM2.5 in India. About 60 % of India's mean population-weighted PM2.5 concentrations come from anthropogenic source sectors, while the remainder are from other sources, windblown dust and extra-regional sources. Leading contributors are residential biomass combustion, power plant and industrial coal combustion and anthropogenic dust (including coal fly ash, fugitive road dust and waste burning). Transportation, brick production and distributed diesel were other contributors to PM2.5. Future evolution of emissions under regulations set at current levels and promulgated levels caused further deterioration of air quality in 2030 and 2050. Under an ambitious prospective policy scenario, promoting very large shifts away from traditional biomass technologies and coal-based electricity generation, significant reductions in PM2.5 levels are achievable in 2030 and 2050. Effective mitigation of future air pollution in India requires adoption of aggressive prospective regulation, currently not formulated

The Continuous Monitoring of Desert Dust using an Infrared-based Dust Detection and Retrieval Method

Science.gov (United States)

Duda, David P.; Minnis, Patrick; Trepte, Qing; Sun-Mack, Sunny

2006-01-01

Airborne dust and sand are significant aerosol sources that can impact the atmospheric and surface radiation budgets. Because airborne dust affects visibility and air quality, it is desirable to monitor the location and concentrations of this aerosol for transportation and public health. Although aerosol retrievals have been derived for many years using visible and near-infrared reflectance measurements from satellites, the detection and quantification of dust from these channels is problematic over bright surfaces, or when dust concentrations are large. In addition, aerosol retrievals from polar orbiting satellites lack the ability to monitor the progression and sources of dust storms. As a complement to current aerosol dust retrieval algorithms, multi-spectral thermal infrared (8-12 micron) data from the Moderate Resolution Imaging Spectroradiometer (MODIS) and the Meteosat-8 Spinning Enhanced Visible and Infrared Imager (SEVIRI) are used in the development of a prototype dust detection method and dust property retrieval that can monitor the progress of Saharan dust fields continuously, both night and day. The dust detection method is incorporated into the processing of CERES (Clouds and the Earth s Radiant Energy System) aerosol retrievals to produce dust property retrievals. Both MODIS (from Terra and Aqua) and SEVERI data are used to develop the method.

Laboratory estimate of the regional shortwave refractive index and single scattering albedo of mineral dust from major sources worldwide

Science.gov (United States)

Di Biagio, C.; Formenti, P.; Caponi, L.; Cazaunau, M.; Pangui, E.; Journet, E.; Nowak, S.; Caquineau, S.; Andreae, M. O.; Kandler, K.; Saeed, T.; Piketh, S.; Seibert, D.; Williams, E.; Balkanski, Y.; Doussin, J. F.

2017-12-01

Mineral dust is one of the most abundant aerosol species in the atmosphere and strongly contributes to the global and regional direct radiative effect. Still large uncertainties persist on the magnitude and overall sign of the dust direct effect, where indeed one of the main unknowns is how much mineral dust absorbs light in the shortwave (SW) spectral range. Aerosol absorption is represented both by the imaginary part (k) of the complex refractive index or the single scattering albedo (SSA, i.e. the ratio of the scattering to extinction coefficient). In this study we present a new dataset of SW complex refractive indices and SSA for mineral dust aerosols obtained from in situ measurements in the 4.2 m3 CESAM simulation chamber at LISA (Laboratoire Interuniversitaire des Systemes Atmospheriques) in Créteil, France. Investigated dust aerosol samples were issued from major desert sources worldwide, including the African Sahara and Sahel, Eastern Asia, the Middle East, Southern Africa, Australia, and the Americas, with differing iron oxides content. Results from the present study provide a regional mapping of the SW absorption by dust and show that the imaginary part of the refractive index largely varies (by up to a factor 6, 0.003-0.02 at 370 nm and 0.001-0.003 at 950 nm) for the different source areas due to the change in the particle iron oxide content. The SSA for dust varies between 0.75-0.90 at 370 nm and 0.95-0.99 at 950 nm, with the largest absorption observed for Sahelian and Australian dust aerosols. Our range of variability for k and SSA is well bracketed by already published literature estimates, but suggests that regional‒dependent values should be used in models. The possible relationship between k and the dust iron oxides content is investigated with the aim of providing a parameterization of the regional‒dependent dust absorption to include in climate models.

Chemical composition and source apportionment of PM10 at an urban background site in a high-altitude Latin American megacity (Bogota, Colombia).

Science.gov (United States)

Ramírez, Omar; Sánchez de la Campa, A M; Amato, Fulvio; Catacolí, Ruth A; Rojas, Néstor Y; de la Rosa, Jesús

2018-02-01

Bogota registers frequent episodes of poor air quality from high PM 10 concentrations. It is one of the main Latin American megacities, located at 2600 m in the tropical Andes, but there is insufficient data on PM 10 source contribution. A characterization of the chemical composition and the source apportionment of PM 10 at an urban background site in Bogota was carried out in this study. Daily samples were collected from June 2015 to May 2016 (a total of 311 samples). Organic carbon (OC), elemental carbon (EC), water soluble compounds (SO 4 2- , Cl - , NO 3 - , NH 4 + ), major elements (Al, Fe, Mg, Ca, Na, K, P) and trace metals (V, Cd, Pb, Sr, Ba, among others) were analyzed. The results were interpreted in terms of their variability during the rainy season (RS) and the dry season (DS). The data obtained revealed that the carbonaceous fraction (∼51%) and mineral dust (23%) were the main PM 10 components, followed by others (15%), Secondary Inorganic Compounds (SIC) (11%) and sea salt (0.4%). The average concentrations of soil, SIC and OC were higher during RS than DS. However, peak values were observed during the DS due to photochemical activity and forest fires. Although trace metals represented <1% of PM 10 , high concentrations of toxic elements such as Pb and Sb on RS, and Cu on DS, were obtained. By using a PMF model, six factors were identified (∼96% PM 10 ) including fugitive dust, road dust, metal processing, secondary PM, vehicles exhaust and industrial emissions. Traffic (exhaust emissions + road dust) was the major PM 10 source, accounting for ∼50% of the PM 10 . The results provided novel data about PM 10 chemical composition, its sources and its seasonal variability during the year, which can help the local government to define control strategies for the main emission sources during the most critical periods. Copyright © 2017 Elsevier Ltd. All rights reserved.

Benchmarking the New RESRAD-OFFSITE Source Term Model with DUST-MS and GoldSim - 13377

Energy Technology Data Exchange (ETDEWEB)

Cheng, J.J.; Kamboj, S.; Gnanapragasam, E.; Yu, C. [Argonne National Laboratory, Argonne, IL 60439 (United States)

2013-07-01

RESRAD-OFFSITE is a computer code developed by Argonne National Laboratory under the sponsorship of U.S. Department of Energy (DOE) and U.S. Nuclear Regulatory Commission (NRC). It is designed on the basis of RESRAD (onsite) code, a computer code designated by DOE and NRC for evaluating soil-contaminated sites for compliance with human health protection requirements pertaining to license termination or environmental remediation. RESRAD-OFFSITE has enhanced capabilities of modeling radionuclide transport to offsite locations and calculating potential radiation exposure to offsite receptors. Recently, a new source term model was incorporated into RESRAD-OFFSITE to enhance its capability further. This new source term model allows simulation of radionuclide releases from different waste forms, in addition to the soil sources originally considered in RESRAD (onsite) and RESRAD-OFFSITE codes. With this new source term model, a variety of applications can be achieved by using RESRAD-OFFSITE, including but not limited to, assessing the performance of radioactive waste disposal facilities. This paper presents the comparison of radionuclide release rates calculated by the new source term model of RESRAD-OFFSITE versus those calculated by DUST-MS and GoldSim, respectively. The focus of comparison is on the release rates of radionuclides from the bottom of the contaminated zone that was assumed to contain radioactive source materials buried in soil. The transport of released contaminants outside of the primary contaminated zone is beyond the scope of this paper. Overall, the agreement between the RESRAD-OFFSITE results and the DUST-MS and GoldSim results is fairly good, with all three codes predicting identical or similar radionuclide release profiles over time. Numerical dispersion in the DUST-MS and GoldSim results was identified as potentially contributing to the disagreement in the release rates. In general, greater discrepancy in the release rates was found for short

Benchmarking the New RESRAD-OFFSITE Source Term Model with DUST-MS and GoldSim - 13377

International Nuclear Information System (INIS)

Cheng, J.J.; Kamboj, S.; Gnanapragasam, E.; Yu, C.

2013-01-01

RESRAD-OFFSITE is a computer code developed by Argonne National Laboratory under the sponsorship of U.S. Department of Energy (DOE) and U.S. Nuclear Regulatory Commission (NRC). It is designed on the basis of RESRAD (onsite) code, a computer code designated by DOE and NRC for evaluating soil-contaminated sites for compliance with human health protection requirements pertaining to license termination or environmental remediation. RESRAD-OFFSITE has enhanced capabilities of modeling radionuclide transport to offsite locations and calculating potential radiation exposure to offsite receptors. Recently, a new source term model was incorporated into RESRAD-OFFSITE to enhance its capability further. This new source term model allows simulation of radionuclide releases from different waste forms, in addition to the soil sources originally considered in RESRAD (onsite) and RESRAD-OFFSITE codes. With this new source term model, a variety of applications can be achieved by using RESRAD-OFFSITE, including but not limited to, assessing the performance of radioactive waste disposal facilities. This paper presents the comparison of radionuclide release rates calculated by the new source term model of RESRAD-OFFSITE versus those calculated by DUST-MS and GoldSim, respectively. The focus of comparison is on the release rates of radionuclides from the bottom of the contaminated zone that was assumed to contain radioactive source materials buried in soil. The transport of released contaminants outside of the primary contaminated zone is beyond the scope of this paper. Overall, the agreement between the RESRAD-OFFSITE results and the DUST-MS and GoldSim results is fairly good, with all three codes predicting identical or similar radionuclide release profiles over time. Numerical dispersion in the DUST-MS and GoldSim results was identified as potentially contributing to the disagreement in the release rates. In general, greater discrepancy in the release rates was found for short

Pollution characteristics, source apportionment, and health risk of heavy metals in street dust of Suzhou, China.

Science.gov (United States)

Lin, Manli; Gui, Herong; Wang, Yao; Peng, Weihua

2017-01-01

To analyze the pollution characteristics, source apportionment, and health risk of heavy metals (HMs) in street dust of Suzhou, China, 23 sampling sites were selected and periodically sampled for 12 months. A total of 276 samples were collected, and the concentrations of selected HMs (e.g., Cr, Cu, Fe, Mn, Pb, V, and Zn) were examined with an X-ray fluorescence spectrum analyzer. Results showed that the mean concentrations of Cr, Cu, Fe, Mn, Pb, V, and Zn in the street dust of Suzhou were 112.9, 27.5, 19941.3, 410.3, 45.2, 75.6, and 225.3 mg kg -1 , respectively. Cr, Cu, Pb, and Zn exceeded their background values in local natural soils by 1.3-3.6-fold, whereas Fe, Mn, and V were all within their background values. However, enrichment factor analysis revealed that Cr, Cu, Mn, Pb, V, and Zn, especially Cr, Cu, Pb, and Zn, were enriched in Suzhou street dust. The HMs showed no significant seasonal changes overall, but spatial distribution analysis implied that the high values of Cr, Cu, Mn, Pb, V, and Zn were mainly distributed in areas with frequent human activities. Results of multivariate techniques (e.g., Pearson correlation, hierarchical cluster, and principal components analyses) suggested that Pb and Zn had complicated sources; Cu and V mainly originated from traffic sources; Fe and Mn mainly came from natural sources; and Cr was dominantly related to industrial district. Health risk assessment revealed that a single heavy metal might not cause both non-cancer and carcinogenic risks to local residents. Nevertheless, the sum of the hazard index of all selected HMs for children slightly exceeded the safety value, thereby implying that the HMs from Suzhou street dust can possibly produce significant risk to children. Cr was the priority pollutant in the study area because of its high concentration, high enrichment, and high contribution to non-cancer risk values.

Air quality impacts analysis for area G. Final report

International Nuclear Information System (INIS)

Kowalewsky, K.; Eklund, B.; Vold, E.L.

1995-01-01

The impact of fugitive radioactive emissions from the disposal site, Area G, was evaluated in support of site characterization for the Performance Assessment and for the Radioactive Air Emissions Management (RAEM) program. Fugitive emissions of tritiated water and contaminated windblown dust were considered. Data from an extensive field measurement program were used to estimate annual emissions of tritiated water. Fugitive dust models were used to calculate estimates of the annual emissions of windblown dust. These estimates were combined with data on contamination levels in surface soils to develop annual emission rates for specific radionuclides: tritium, uranium-238, cesium-137, plutonium-238, plutonium-239,240, and strontium-90. The CAP-88 atmospheric transport model was used to predict areas potentially affected by long-term dust deposition and atmospheric concentrations. The annual emission rate of tritiated water was estimated from the field data to be 14.0 Ci/yr. The emission rate of soil-borne radionuclides from open areas and from soils handling operations totaled less than 1x10 -4 Ci/yr. The CAP-88 results were used to develop effective dose equivalents (EDEs) for receptor locations downwind of Area G. All EDEs were several orders of magnitude below the national standard of 10 mrem/yr. Fugitive air emissions from Area G were found not to pose a health threat to persons living or working downwind of the facility

INFRARED LUMINOSITIES AND DUST PROPERTIES OF z ∼ 2 DUST-OBSCURED GALAXIES

International Nuclear Information System (INIS)

Bussmann, R. S.; Dey, Arjun; Jannuzi, B. T.; Borys, C.; Desai, V.; Sheth, K.; Soifer, B. T.; Le Floc'h, E.; Melbourne, J.

2009-01-01

We present SHARC-II 350 μm imaging of twelve 24 μm bright (F 24μm > 0.8 mJy) Dust-Obscured Galaxies (DOGs) and Combined Array for Research in Millimeter-wave Astronomy (CARMA) 1 mm imaging of a subset of two DOGs. These objects are selected from the Booetes field of the NOAO Deep Wide-Field Survey. Detections of four DOGs at 350 μm imply infrared (IR) luminosities which are consistent to within a factor of 2 of expectations based on a warm-dust spectral energy distribution (SED) scaled to the observed 24 μm flux density. The 350 μm upper limits for the 8 non-detected DOGs are consistent with both Mrk 231 and M82 (warm-dust SEDs), but exclude cold dust (Arp 220) SEDs. The two DOGs targeted at 1 mm were not detected in our CARMA observations, placing strong constraints on the dust temperature: T dust > 35-60 K. Assuming these dust properties apply to the entire sample, we find dust masses of ∼3 x 10 8 M sun . In comparison to other dusty z ∼ 2 galaxy populations such as submillimeter galaxies (SMGs) and other Spitzer-selected high-redshift sources, this sample of DOGs has higher IR luminosities (2 x 10 13 L sun versus 6 x 10 12 L sun for the other galaxy populations) that are driven by warmer dust temperatures (>35-60 K versus ∼30 K) and lower inferred dust masses (3 x 10 8 M sun versus 3 x 10 9 M sun ). Wide-field Herschel and Submillimeter Common-User Bolometer Array-2 surveys should be able to detect hundreds of these power-law-dominated DOGs. We use the existing Hubble Space Telescope and Spitzer/InfraRed Array Camera data to estimate stellar masses of these sources and find that the stellar to gas mass ratio may be higher in our 24 μm bright sample of DOGs than in SMGs and other Spitzer-selected sources. Although much larger sample sizes are needed to provide a definitive conclusion, the data are consistent with an evolutionary trend in which the formation of massive galaxies at z ∼ 2 involves a submillimeter bright, cold-dust, and star

Control of harmful dust in coal mines

Energy Technology Data Exchange (ETDEWEB)

Goddard, B; Bower, K; Mitchell, D

1973-01-01

This handbook consists of a series of short chapters devoted to: sources of airborne dust; dust standards and methods of sampling; dust prevention on mechanized faces; ventilation and dust extraction; distribution and use of water; dust control on mechanized faces; dust control in drivages and headings; drilling and shotfiring; dust control in transport; some outbye dust control techniques (hygroscopic salts, impingement curtains); water infusion; personal protective equipment. (CIS Abstr.)

Food allergens in mattress dust in Norwegian homes - a potentially important source of allergen exposure.

Science.gov (United States)

Bertelsen, R J; Faeste, C K; Granum, B; Egaas, E; London, S J; Carlsen, K-H; Lødrup Carlsen, K C; Løvik, M

2014-01-01

Sensitization to food allergens and food allergic reactions are mostly caused by ingesting the allergen, but can also occur from exposure via the respiratory tract or the skin. Little is known about exposure to food allergens in the home environment. The objective of this study was firstly to describe the frequency of detection of allergens from fish, egg, milk, and peanut in mattress dust collected from homes of 13-year-old adolescents and secondly to identify home characteristics associated with the presence of food allergen contamination in dust. Food allergens were measured by dot blot analysis in mattress dust from 143 homes in Oslo, Norway. We analysed associations between home characteristics (collected by parental questionnaires and study technicians) and food allergens by multivariate regression models. Fish allergen was detected in 46%, peanut in 41%, milk in 39%, and egg allergen in 22% of the mattress dust samples; only three samples contained none of these allergens. All four food allergens were more frequently detected in mattresses in small dwellings (Food allergens occurred frequently in beds in Norwegian homes, with dwelling size and proximity of kitchen and bedroom as the most important determinants. Due to the amount of time children spent in the bedroom, mattress dust may be an important source of exposure to food allergens. © 2013 John Wiley & Sons Ltd.

High-latitude dust in the Earth system

Science.gov (United States)

Bullard, Joanna E; Baddock, Matthew; Bradwell, Tom; Crusius, John; Darlington, Eleanor; Gaiero, Diego; Gasso, Santiago; Gisladottir, Gudrun; Hodgkins, Richard; McCulloch, Robert; NcKenna Neuman, Cheryl; Mockford, Tom; Stewart, Helena; Thorsteinsson, Throstur

2016-01-01

Natural dust is often associated with hot, subtropical deserts, but significant dust events have been reported from cold, high latitudes. This review synthesizes current understanding of high-latitude (≥50°N and ≥40°S) dust source geography and dynamics and provides a prospectus for future research on the topic. Although the fundamental processes controlling aeolian dust emissions in high latitudes are essentially the same as in temperate regions, there are additional processes specific to or enhanced in cold regions. These include low temperatures, humidity, strong winds, permafrost and niveo-aeolian processes all of which can affect the efficiency of dust emission and distribution of sediments. Dust deposition at high latitudes can provide nutrients to the marine system, specifically by contributing iron to high-nutrient, low-chlorophyll oceans; it also affects ice albedo and melt rates. There have been no attempts to quantify systematically the expanse, characteristics, or dynamics of high-latitude dust sources. To address this, we identify and compare the main sources and drivers of dust emissions in the Northern (Alaska, Canada, Greenland, and Iceland) and Southern (Antarctica, New Zealand, and Patagonia) Hemispheres. The scarcity of year-round observations and limitations of satellite remote sensing data at high latitudes are discussed. It is estimated that under contemporary conditions high-latitude sources cover >500,000 km2 and contribute at least 80–100 Tg yr−1 of dust to the Earth system (~5% of the global dust budget); both are projected to increase under future climate change scenarios.

High Latitude Dust in the Earth System

Science.gov (United States)

Bullard, Joanna E.; Baddock, Matthew; Bradwell, Tom; Crusius, John; Darlington, Eleanor; Gaiero, Diego; Gasso, Santiago; Gisladottir, Gudrun; Hodgkins, Richard; McCulloch, Robert;

Neutron activation analysis on sediments from Victoria Land, Antarctica. Multi-elemental characterization of potential atmospheric dust sources

International Nuclear Information System (INIS)

Baccolo, G.; Maggi, V.; Baroni, C.; Clemenza, M.; Motta, A.; Nastasi, M.; Previtali, E.; University of Milano-Bicocca, Milan; Delmonte, B.; Salvatore, M.C.

2014-01-01

The elemental composition of 40 samples of mineral sediments collected in Victoria Land, Antarctica, in correspondence of ice-free sites, is presented. Concentration of 36 elements was determined by instrumental neutron activation analysis, INAA. The selection of 6 standard reference materials and the development of a specific analytical procedure allowed to reduce measurements uncertainties and to verify the reproducibility of the results. The decision to analyze sediment samples from Victoria Land ice-free areas is related to recent investigations regarding mineral dust content in the TALos Dome ICE core (159deg11'E; 72deg49'S, East Antarctica, Victoria Land), in which a coarse local fraction of dust was recognized. The characterization of Antarctic potential source areas of atmospheric mineral dust is the first step to identify the active sources of dust for the Talos Dome area and to reconstruct the atmospheric pathways followed by air masses in this region during different climatic periods. Principal components analysis was used to identify elements and samples correlations; attention was paid specially to rare earth elements (REE) and incompatible/compatible elements (ICE) in respect to iron, which proved to be the most discriminating elemental groups. The analysis of REE and ICE concentration profiles supported evidences of chemical weathering in ice-free areas of Victoria Land, whereas cold and dry climate conditions of the Talos Dome area and in general of East Antarctica. (author)

Quantification of Fugitive Methane Emissions with Spatially Correlated Measurements Collected with Novel Plume Camera

Science.gov (United States)

Tsai, Tracy; Rella, Chris; Crosson, Eric

2013-04-01

Quantification of fugitive methane emissions from unconventional natural gas (i.e. shale gas, tight sand gas, etc.) production, processing, and transport is essential for scientists, policy-makers, and the energy industry, because methane has a global warming potential of at least 21 times that of carbon dioxide over a span of 100 years [1]. Therefore, fugitive emissions reduce any environmental benefits to using natural gas instead of traditional fossil fuels [2]. Current measurement techniques involve first locating all the possible leaks and then measuring the emission of each leak. This technique is a painstaking and slow process that cannot be scaled up to the large size of the natural gas industry in which there are at least half a million natural gas wells in the United States alone [3]. An alternative method is to calculate the emission of a plume through dispersion modeling. This method is a scalable approach since all the individual leaks within a natural gas facility can be aggregated into a single plume measurement. However, plume dispersion modeling requires additional knowledge of the distance to the source, atmospheric turbulence, and local topography, and it is a mathematically intensive process. Therefore, there is a need for an instrument capable of simple, rapid, and accurate measurements of fugitive methane emissions on a per well head scale. We will present the "plume camera" instrument, which simultaneously measures methane at different spatial points or pixels. The spatial correlation between methane measurements provides spatial information of the plume, and in addition to the wind measurement collected with a sonic anemometer, the flux can be determined. Unlike the plume dispersion model, this approach does not require knowledge of the distance to the source and atmospheric conditions. Moreover, the instrument can fit inside a standard car such that emission measurements can be performed on a per well head basis. In a controlled experiment

Multi-element characterization and source identification of trace metal in road dust from an industrial city in semi-humid area of Northwest China

International Nuclear Information System (INIS)

Mengmeng Zhang; Xinwei Lu; Hao Chen; Panpan Gao; Yi Fu

2015-01-01

Concentrations and sources of multi-elements in road dusts from an industrial city of northwest China were determined. Dust samples have elevated concentrations of Co, Cr, Cu, Pb, Zn, Sr and Ba. The dusts were mainly moderate enrichment by Co and Pb, minimal enrichment to moderate enrichment by Sr and Zn, and deficiency to minimal enrichment by other trace metals. Mn, V, Y, La, Hf, Th and U originated from soil. Cu, Pb, Cr, Ba and Sr mainly derived from traffic. Co, Zr, Ni, Ga, As and Zn have mixed sources of nature, industry and traffic. (author)

Sources of hydrocarbons in urban road dust: Identification, quantification and prediction.

Science.gov (United States)

Mummullage, Sandya; Egodawatta, Prasanna; Ayoko, Godwin A; Goonetilleke, Ashantha

2016-09-01

Among urban stormwater pollutants, hydrocarbons are a significant environmental concern due to their toxicity and relatively stable chemical structure. This study focused on the identification of hydrocarbon contributing sources to urban road dust and approaches for the quantification of pollutant loads to enhance the design of source control measures. The study confirmed the validity of the use of mathematical techniques of principal component analysis (PCA) and hierarchical cluster analysis (HCA) for source identification and principal component analysis/absolute principal component scores (PCA/APCS) receptor model for pollutant load quantification. Study outcomes identified non-combusted lubrication oils, non-combusted diesel fuels and tyre and asphalt wear as the three most critical urban hydrocarbon sources. The site specific variabilities of contributions from sources were replicated using three mathematical models. The models employed predictor variables of daily traffic volume (DTV), road surface texture depth (TD), slope of the road section (SLP), effective population (EPOP) and effective impervious fraction (EIF), which can be considered as the five governing parameters of pollutant generation, deposition and redistribution. Models were developed such that they can be applicable in determining hydrocarbon contributions from urban sites enabling effective design of source control measures. Copyright © 2016 Elsevier Ltd. All rights reserved.

Dust Generation Resulting from Desiccation of Playa Systems: Studies on Mono and Owens Lakes, California

Science.gov (United States)

Gill, Thomas Edward

1995-01-01

Playas, evaporites, and aeolian sediments frequently are linked components within the Earth system. Anthropogenic water diversions from terminal lakes form playas that release fugitive dust. These actions, documented worldwide, simulate aeolian processes activated during palaeoclimatic pluvial/interpluvial transitions, and have significant environmental impacts. Pluvial lakes Russell and Owens in North America's Great Basin preceded historic Mono and Owens Lakes, now desiccated by water diversions into dust-generating, evaporite -encrusted playas. Geochemical and hydrologic cycles acting on the Owens (Dry) Lake playa form three distinct crust types each year. Although initial dust production results from deflation of surface efflorescences after the playa dries, most aerosols are created by saltation abrasion of salt/silt/clay crusts at crust/ sand sheet contacts. The warm-season, clastic "cemented" crust is slowest to degrade into dust. If the playa surface is stabilized by an unbroken, non-efflorescent crust, dust formation is discouraged. When Mono Lake's surFace elevation does not exceed 1951 meters (6400 feet), similar processes will also generate dust from its saline lower playa. Six factors--related to wind, topography, groundwater, and sediments--control dust formation at both playas. These factors were combined into a statistical model relating suspended dust concentrations to playa/lake morphometry. The model shows the extent and severity of Mono Lake dust storms expands significantly below the surface level 6376 feet (1943.5 meters). X-ray diffraction analysis of Mono Basin soils, playa sediments, and aerosols demonstrates geochemical cycling of materials through land, air and water during Mono Lake's 1982 low stand. Soils and clastic playa sediments contain silicate minerals and tephra. Saline groundwater deposited calcite, halite, thenardite, gaylussite, burkeite and glauberite onto the lower playa. Aerosols contained silicate minerals (especially

CHARACTERIZATION OF THE FUGITIVE MERCURY EMISSIONS AT A CHLOR-ALKALI PLANT. OVERALL STUDY DESIGN

Science.gov (United States)

The paper discusses a detailed emissions measurement campaign that was conducted over a 9-day period within a mercury (Hg) cell chlor-alkali plant in the southeastern United States (U.S.). The principal focus of this study was to measure fugitive (non-ducted) airborne Hg emission...

Seasonal provenance changes in present-day Saharan dust collected in and off Mauritania

Directory of Open Access Journals (Sweden)

C. A. Friese

2017-08-01

Full Text Available Saharan dust has a crucial influence on the earth climate system and its emission, transport and deposition are intimately related to, e.g., wind speed, precipitation, temperature and vegetation cover. The alteration in the physical and chemical properties of Saharan dust due to environmental changes is often used to reconstruct the climate of the past. However, to better interpret possible climate changes the dust source regions need to be known. By analysing the mineralogical composition of transported or deposited dust, potential dust source areas can be inferred. Summer dust transport off northwest Africa occurs in the Saharan air layer (SAL. In continental dust source areas, dust is also transported in the SAL; however, the predominant dust input occurs from nearby dust sources with the low-level trade winds. Hence, the source regions and related mineralogical tracers differ with season and sampling location. To test this, dust collected in traps onshore and in oceanic sediment traps off Mauritania during 2013 to 2015 was analysed. Meteorological data, particle-size distributions, back-trajectory and mineralogical analyses were compared to derive the dust provenance and dispersal. For the onshore dust samples, the source regions varied according to the seasonal changes in trade-wind direction. Gibbsite and dolomite indicated a Western Saharan and local source during summer, while chlorite, serpentine and rutile indicated a source in Mauritania and Mali during winter. In contrast, for the samples that were collected offshore, dust sources varied according to the seasonal change in the dust transporting air layer. In summer, dust was transported in the SAL from Mauritania, Mali and Libya as indicated by ferroglaucophane and zeolite. In winter, dust was transported with the trades from Western Sahara as indicated by, e.g., fluellite.

Dust-gas interaction deduced from Halley multicolour camera observations

International Nuclear Information System (INIS)

Huebner, W.F.; Delamere, W.A.; Keller, H.U.; Reitsema, H.J.; Schmidt, H.U.; Whipple, F.L.; Wilhelm, K.

1986-01-01

The dust and gas productions of Comet Halley were measured by the dust counter and the mass spectrometers on the Giotto spacecraft. These instruments give only little information about the spatial asymmetry of the activity. The asymmetry in the dust production is clearly evident from the dust jets seen in the Halley Multicolour Camera images. Since the dust is entrained by the gas, production must be similarly asymmetric. The intensity profiles along and across several dust jets are related to their source regions on the nucleus. Properties of the dust jets are investigated. A few compact, but highly active source regions on the nucleus produce most of the visible dust and can account for most of the gas produced by the comet. 2 refs

Connecting the Plots: The Extension of Return and Korean Ethnic Nationalism in Jane Jeong Trenka’s 'Fugitive Visions'

Directory of Open Access Journals (Sweden)

Ethan Waddell

2017-05-01

Full Text Available Thousands of overseas Korean adoptees return to Korea temporarily each year in search of their true origin, but few choose to stay permanently. A prominent member of this small community is Jane Jeong Trenka, author of two memoirs: The Language of Blood (2003 and Fugitive Visions: An Adoptee’s Return to Korea (2009. This article analyses Trenka’s literary struggle for permanence in Fugitive Visions through theories on Korean ethnic national identity. Using Marshall McLuhan’s idea of media as the ‘extension of man’, it explores the symbiotic relationship between literary media and identity, connecting colonial-era writings on Korean ethnic nationalism to Trenka’s portrayal of transnational return.

Assessment for potential radionuclide emissions from stacks and diffuse and fugitive sources on the Hanford Site

International Nuclear Information System (INIS)

Davis, W.E.; Schmidt, J.W.; Gleckler, B.P.; Rhoads, K.

1995-06-01

By using the six EPA-approved methods, instead of only the original back calculation method for assessing the 84 WHC registered stacks, the number of stacks requiring continuous monitoring was reduced from 32 to 19 stacks. The intercomparison between results showed that no correlation existed between back calculations and release fractions. Also the NDA, upstream air samples, and powder release fraction method results were at least three orders of magnitude lower then the back calculations results. The most surprising results of the assessment came from NDA. NDA was found to be an easy method for assessing potential emissions. For the nine stacks assessed by NDA, all nine of the stacks would have required continuous monitoring when assessed by back calculations. However, when NDA was applied all stacks had potential emissions that would cause an EDE below the > 0.1 mrem/y standard. Apparent DFs for the HEPA filter systems were calculated for eight nondesignated stacks with emissions above the detection limit. These apparent DFs ranged from 0.5 to 250. The EDE dose to the MEI was calculated to be 0.028 mrem/y for diffuse and fugitive emissions from the Hanford Sited. This is well below the > 0.1 mrem/y standard

Occurrence, sources and human exposure assessment of SCCPs in indoor dust of northeast China.

Science.gov (United States)

Liu, Li-Hua; Ma, Wan-Li; Liu, Li-Yan; Huo, Chun-Yan; Li, Wen-Long; Gao, Chong-Jing; Li, Hai-Ling; Li, Yi-Fan; Chan, Hing Man

2017-06-01

Short-chain chlorinated paraffins (SCCPs) are widely used chemicals in household products and might cause adverse human health effects. However, limited information is available on the occurrence of SCCPs in indoor environments and their exposure risks on humans. In this study the concentrations, profiles and human exposure of SCCPs in indoor dust from five different indoor environments, including commercial stores, residential apartments, dormitories, offices and laboratories were characterized. The SCCPs levels ranged from 10.1 to 173.0 μg/g, with the median and mean concentration of 47.2 and 53.6 μg/g, respectively. No significant difference was found on concentrations among the five microenvironments. The most abundant compounds in indoor dust samples were homologues of C 13 group, Cl 7 group and N 20 (N is the total number of C and Cl) group. In the five microenvironments, commercial stores were more frequently exposed to shorter carbon chained and higher chlorinated homologues. Three potential sources for SCCPs were identified by the multiple linear regression of factor score model and correspondence analysis. The major sources of SCCPs in indoor dust were technical mixtures of CP-42 (42% chlorine, w/w) and CP-52 b (52% chlorine, w/w). The total daily exposure doses and hazard quotients (HQ) were calculated by the human exposure models, and they were all below the reference doses and threshold values, respectively. Monte Carlo simulation was applied to predict the human exposure risk of SCCPs. Infants and toddlers were at risk of SCCPs based on predicted HQ values, which were exceeded the threshold for neoplastic effects in the worst case. Our results on the occurrences, sources and human exposures of SCCPs will be useful to provide a better understanding of SCCPs behaviors in indoor environment in China, and to support environmental risk evaluation and regulation of SCCPs in the world. Copyright © 2017. Published by Elsevier Ltd.

78 FR 23677 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

Science.gov (United States)

2013-04-22

...EPA is finalizing approval of revisions to the Imperial County Air Pollution Control District (ICAPCD) portion of the California State Implementation Plan (SIP). This action was proposed in the Federal Register on January 7, 2013 and concerns local rules that regulate inhalable particulate matter (PM) emissions from sources of fugitive dust such as unpaved roads and disturbed soils in open and agricultural areas in Imperial County. We are approving local rules that regulate these emission sources under the Clean Air Act (CAA or the Act).

77 FR 19153 - Nonpayment of Benefits to Fugitive Felons and Probation or Parole Violators

Science.gov (United States)

2012-03-30

... toll-free number, 1-800-772-1213 or TTY 1-800-325-0778, or visit our Internet site, Social Security... SOCIAL SECURITY ADMINISTRATION 20 CFR Parts 404 and 416 [Docket No. SSA 2006-0173] RIN 0960-AG12 Nonpayment of Benefits to Fugitive Felons and Probation or Parole Violators AGENCY: Social Security...

Correlation between Yellow Dust and Radioactivity

International Nuclear Information System (INIS)

AIZaabia, Mouza A; Kim, Byoung-Jik

2015-01-01

In East Asia, yellow dust or Asian Dust (AD) outbreaks are among the largest contributors of wind-blown dust that carry natural and anthropogenic radionuclides and subsequently alter their concentration and distribution throughout the environment. Although the Korean Peninsula has been experiencing AD events since ancient times, the research has tended to focus on the transport routes and characteristics of AD, rather than on its impact on radionuclide activity levels. This paper examines the relationship between radionuclide concentration in the air and the frequency of dusty days in South Korea during AD intrusion events. It also investigates whether increased radionuclide concentration is a function of either more mass or more dust contamination. In this study, significant linear correlations of gamma-emitting radionuclides were found with mass of dust and occurrence frequency of AD. Regardless of the source origin of the dust, 137 Cs and 7 Be concentration primarily depended on dust mass in the filter. Nonetheless, the correlations were greatly distorted in 2011 and in the spring season, particularly the correlations with AD days that were far below that of the correlations obtained for the whole study period. A possible explanation of these conflicting results is that a change in the dust source could appreciably alter the concentration, deposition, and distribution of airborne radionuclides

Arabian Red Sea coastal soils as potential mineral dust sources

KAUST Repository

Prakash, P. Jish; Stenchikov, Georgiy L.; Tao, Weichun; Yapici, Tahir; Warsama, Bashir H.; Engelbrecht, Johann

2016-01-01

, because of its proximity, directly affects the Red Sea and coastal urban centers. The potential of soils to be suspended as airborne mineral dust depends largely on soil texture, moisture content and particle size distributions. Airborne dust inevitably

Utilization of waste coconut coir dust as a source of fuel

Energy Technology Data Exchange (ETDEWEB)

Festin, T.F.; Jose, W.I.

1979-01-01

A review on the production of a gaseous fuel by the pyrolysis of waste coir dust, which is a by-product in the manufacturing of coir fibers from coconut husks. Experimental and pilot-plant studies on the pyrolysis of coir dust are discussed and the properties of the dust and the fuel gas produced are given. (Refs. 13).

Computation of radionuclide particulate finite area fugitive source strengths

Energy Technology Data Exchange (ETDEWEB)

Fields, D E

1983-06-01

Atmospheric source strengths quantifying particulate re-suspension from wind and non-wind disturbance-driven processes are computed for sites of small area. These values are useful in computing downwind air concentration values to evaluate risk to exposed populations. The net source strength for the site is the sum of the wind- and disturbance-driven components. A unified source strength approach includes both classes of re-suspension processes. More research is needed to satisfactorily express the time-dependence of re-suspension parameters, especially in non-arid climates where population densities are greater. (JMT)

Source influence on emission pathways and ambient PM2.5 pollution over India (2015–2050

Directory of Open Access Journals (Sweden)

C. Venkataraman

2018-06-01

Full Text Available India is currently experiencing degraded air quality, and future economic development will lead to challenges for air quality management. Scenarios of sectoral emissions of fine particulate matter and its precursors were developed and evaluated for 2015–2050, under specific pathways of diffusion of cleaner and more energy-efficient technologies. The impacts of individual source sectors on PM2.5 concentrations were assessed through systematic simulations of spatially and temporally resolved particulate matter concentrations, using the GEOS-Chem model, followed by population-weighted aggregation to national and state levels. We find that PM2.5 pollution is a pan-India problem, with a regional character, and is not limited to urban areas or megacities. Under present-day emissions, levels in most states exceeded the national PM2.5 annual standard (40 µg m−3. Sources related to human activities were responsible for the largest proportion of the present-day population exposure to PM2.5 in India. About 60 % of India's mean population-weighted PM2.5 concentrations come from anthropogenic source sectors, while the remainder are from other sources, windblown dust and extra-regional sources. Leading contributors are residential biomass combustion, power plant and industrial coal combustion and anthropogenic dust (including coal fly ash, fugitive road dust and waste burning. Transportation, brick production and distributed diesel were other contributors to PM2.5. Future evolution of emissions under regulations set at current levels and promulgated levels caused further deterioration of air quality in 2030 and 2050. Under an ambitious prospective policy scenario, promoting very large shifts away from traditional biomass technologies and coal-based electricity generation, significant reductions in PM2.5 levels are achievable in 2030 and 2050. Effective mitigation of future air pollution in India requires adoption of aggressive prospective

Dust in H II regions

International Nuclear Information System (INIS)

Isobe, S.

1977-01-01

Several pieces of evidence indicate that H II regions may contain dust: 1) the continuum light scattered by dust grains (O'Dell and Hubbard, 1965), 2) thermal radiation from dust grains at infrared wavelengths (Ney and Allen, 1969), 3) the abnormal helium abundance in some H II regions (Peimbert and Costero, 1969), etc. Although observations of the scattered continuum suggest that the H II region cores may be dust-free, dust grains and gas must be well mixed in view of the infrared observations. This difficulty may be solved by introducing globules with sizes approximately 0.001 pc. These globules and the molecular clouds adjacent to H II regions are the main sources supplying dust to H II regions. (Auth.)

Desert Dust and Health: A Central Asian Review and Steppe Case Study

Directory of Open Access Journals (Sweden)

Troy Sternberg

2017-11-01

Full Text Available In Asian deserts environmental and anthropomorphic dust is a significant health risk to rural populations. Natural sources in dry landscapes are exacerbated by human activities that increase the vulnerability to dust and dust-borne disease vectors. Today in Central and Inner Asian drylands, agriculture, mining, and rapid development contribute to dust generation and community exposure. Thorough review of limited dust investigation in the region implies but does not quantify health risks. Anthropogenic sources, such as the drying of the Aral Sea, highlight the shifting dust dynamics across the Central EurAsian steppe. In the Gobi Desert, our case study in Khanbogd, Mongolia addressed large-scale mining’s potential dust risk to the health of the local population. Dust traps showed variable exposure to particulates among herder households and town residents; dust density distribution indicated that sources beyond the mine need to be considered when identifying particulate sources. Research suggests that atmospheric dust from multiple causes may enhance human particulate exposure. Greater awareness of dust in greater Central Asia reflects community concern about related health implications. Future human well-being in the region will require more thorough information on dust emissions in the changing environment.

Desert Dust and Health: A Central Asian Review and Steppe Case Study.

Science.gov (United States)

Sternberg, Troy; Edwards, Mona

2017-11-03

In Asian deserts environmental and anthropomorphic dust is a significant health risk to rural populations. Natural sources in dry landscapes are exacerbated by human activities that increase the vulnerability to dust and dust-borne disease vectors. Today in Central and Inner Asian drylands, agriculture, mining, and rapid development contribute to dust generation and community exposure. Thorough review of limited dust investigation in the region implies but does not quantify health risks. Anthropogenic sources, such as the drying of the Aral Sea, highlight the shifting dust dynamics across the Central EurAsian steppe. In the Gobi Desert, our case study in Khanbogd, Mongolia addressed large-scale mining's potential dust risk to the health of the local population. Dust traps showed variable exposure to particulates among herder households and town residents; dust density distribution indicated that sources beyond the mine need to be considered when identifying particulate sources. Research suggests that atmospheric dust from multiple causes may enhance human particulate exposure. Greater awareness of dust in greater Central Asia reflects community concern about related health implications. Future human well-being in the region will require more thorough information on dust emissions in the changing environment.

Concentrations and source apportionment of PM10 and associated elemental and ionic species in a lignite-burning power generation area of southern Greece.

Science.gov (United States)

Argyropoulos, G; Grigoratos, Th; Voutsinas, M; Samara, C

2013-10-01

Ambient concentrations of PM10 and associated elemental and ionic species were measured over the cold and the warm months of 2010 at an urban and two rural sites located in the lignite-fired power generation area of Megalopolis in Peloponnese, southern Greece. The PM10 concentrations at the urban site (44.2 ± 33.6 μg m(-3)) were significantly higher than those at the rural sites (23.7 ± 20.4 and 22.7 ± 26.9 μg m(-3)). Source apportionment of PM10 and associated components was accomplished by an advanced computational procedure, the robotic chemical mass balance model (RCMB), using chemical profiles for a variety of local fugitive dust sources (power plant fly ash, flue gas desulfurization wet ash, feeding lignite, infertile material from the opencast mines, paved and unpaved road dusts, soil), which were resuspended and sampled through a PM10 inlet onto filters and then chemically analyzed, as well as of other common sources such as vehicular traffic, residential oil combustion, biomass burning, uncontrolled waste burning, marine aerosol, and secondary aerosol formation. Geological dusts (road/soil dust) were found to be major PM10 contributors in both the cold and warm periods of the year, with average annual contribution of 32.6 % at the urban site vs. 22.0 and 29.0 % at the rural sites. Secondary aerosol also appeared to be a significant source, contributing 22.1 % at the urban site in comparison to 30.6 and 28.7 % at the rural sites. At all sites, the contribution of biomass burning was most significant in winter (28.2 % at the urban site vs. 14.6 and 24.6 % at the rural sites), whereas vehicular exhaust contribution appeared to be important mostly in the summer (21.9 % at the urban site vs. 11.5 and 10.5 % at the rural sites). The highest contribution of fly ash (33.2 %) was found at the rural site located to the north of the power plants during wintertime, when winds are favorable. In the warm period, the highest contribution of fly ash was found at the

Engineering-scale dust control experiments

International Nuclear Information System (INIS)

Winberg, M.R.; Pawelko, R.J.; Jacobs, N.C.; Thompson, D.N.

1990-12-01

This report presents the results of engineering scale dust-control experiments relating to contamination control during handling of transuranic waste. These experiments focused on controlling dust during retrieval operations of buried waste where waste and soil are intimately mixed. Sources of dust generation during retrieval operations include digging, dumping, and vehicle traffic. Because contaminants are expected to attach to soil particles and move with the generated dust, control of the dust spread may be the key to contamination control. Dust control techniques examined in these experiments include the use of misting systems, soil fixatives, and dust suppression agents. The Dryfog Ultrasonic Misting Head, manufactured by Sonics, Incorporated, and ENTAC, an organic resin derived from tree sap manufactured by ENTAC Corporation, were tested. The results of the experiments include product performance and recommended application methods. 19 figs., 7 refs., 6 tabs

Featured Image: Making Dust in the Lab

Science.gov (United States)

Kohler, Susanna

2017-12-01

This remarkable photograph (which spans only 10 m across; click for a full view) reveals what happens when you form dust grains in a laboratory under conditions similar to those of interstellar space. The cosmic life cycle of dust grains is not well understood we know that in the interstellar medium (ISM), dust is destroyed at a higher rate than it is produced by stellar sources. Since the amount of dust in the ISM stays constant, however, there must be additional sources of dust production besides stars. A team of scientists led by Daniele Fulvio (Pontifical Catholic University of Rio de Janeiro and the Max Planck Institute for Astronomy at the Friedrich Schiller University Jena) have now studied formation mechanisms of dust grains in the lab by mimicking low-temperature ISM conditions and exploring how, under these conditions, carbonaceous materials condense from gas phase to form dust grains. To read more about their results and see additional images, check out the paper below.CitationDaniele Fulvio et al 2017 ApJS 233 14. doi:10.3847/1538-4365/aa9224

78 FR 894 - Interim Final Determination To Stay Sanctions, Imperial County Air Pollution Control District

Science.gov (United States)

2013-01-07

...EPA is making an interim final determination to stay imposition of sanctions based on a proposed approval of revisions to the Imperial County Air Pollution Control District (ICAPCD) portion of the California State Implementation Plan (SIP) published elsewhere in this Federal Register. The revisions concern local rules that regulate inhalable particulate matter (PM10) emissions from sources of fugitive dust such as unpaved roads and disturbed soils in open and agricultural areas in Imperial County.

Qualitative risk assessment for the 100-FR-1 source operable unit

International Nuclear Information System (INIS)

Corporation, I.T.

1994-08-01

This report provides the Qualitative risk assessment (QRA) for the waste sites associated with the 100-FR-1 Operable Unit. The QRA is an evaluation of risk for a predefined set of human and ecological exposure scenarios. It is not intended to replace or be a substitute for a baseline risk assessment. The QRA is streamlined to consider only two human health scenarios (frequent-and occasional-use) with four exposure pathways (soil ingestion, fugitive dust inhalation, inhalation of volatile organics, and external radiation exposure) and a limited ecological evaluation. The use of these scenarios and pathways was agreed to by the 100 Area Tri-Party unit managers

Measurement of fugitive emissions from gas processing plants in Alberta

Energy Technology Data Exchange (ETDEWEB)

Chambers, A. [Alberta Research Council, Edmonton, AB (Canada)

2004-07-01

This paper presents a new gas visualization camera created to detect leaks. An outline of the device's projected entry into the oil and gas industry was provided, and included: a demonstration of Differential Absorption Light Detection and Ranging (DIAL) and leak cameras to measure and reduce fugitive emissions; a comparison of DIAL measured emissions with estimated emissions; and a review of methods to measure particulate emissions. In addition, a background of gas leak visualisation technology was presented along with an an overview of DIAL and its results from sour gas plants. The results of a survey conducted in 2003 were presented, including leaks identified and repaired as well as a follow up leak survey. An analysis of pre and post-repair hydrocarbon emissions from the Deepcut area revealed a 60 per cent reduction with savings of $140,000 as well as additional savings from reduced carbon emissions. A similar survey conducted in another plant measured emissions from condensate tanks before and after cooler installation as well as from surrounding well sites, quantifying an 80 per cent reduction in methane emissions. Tasks identified for future research concerned particulate emissions and the development of Lidar methods which can currently identify particulates, but are not yet able to quantify them. Other tasks included a complete DIAL data workup and reporting; the quantification of both methane and carbon emissions reduction at a sour gas plant; a comparison of measured emissions with methods that estimate fugitives; and a complete review of particulate measurements. tabs, figs.

A new approach to estimate fugitive methane emissions from coal mining in China

Energy Technology Data Exchange (ETDEWEB)

Ju, Yiwen, E-mail: juyw03@163.com [Key Laboratory of Computational Geodynamics of Chinese Academy Sciences, Beijing 100049 (China); College of Earth Science, University of Chinese Academy Sciences, Beijing 100049 (China); Sun, Yue [Key Laboratory of Computational Geodynamics of Chinese Academy Sciences, Beijing 100049 (China); College of Earth Science, University of Chinese Academy Sciences, Beijing 100049 (China); Sa, Zhanyou [Department of Safety Engineering, Qingdao Technological University, Qingdao 266520 (China); Pan, Jienan [School of Resources and Environment, Henan Polytechnic University, Jiaozuo 454000 (China); Wang, Jilin [School of Resources and Geosciences, China University of Mining and Technology, Xuzhou 221116 (China); Hou, Quanlin; Li, Qingguang; Yan, Zhifeng [Key Laboratory of Computational Geodynamics of Chinese Academy Sciences, Beijing 100049 (China); College of Earth Science, University of Chinese Academy Sciences, Beijing 100049 (China); Liu, Jie [Department of Safety Engineering, Qingdao Technological University, Qingdao 266520 (China)

2016-02-01

Developing a more accurate greenhouse gas (GHG) emissions inventory draws too much attention. Because of its resource endowment and technical status, China has made coal-related GHG emissions a big part of its inventory. Lacking a stoichiometric carbon conversion coefficient and influenced by geological conditions and mining technologies, previous efforts to estimate fugitive methane emissions from coal mining in China has led to disagreeing results. This paper proposes a new calculation methodology to determine fugitive methane emissions from coal mining based on the domestic analysis of gas geology, gas emission features, and the merits and demerits of existing estimation methods. This new approach involves four main parameters: in-situ original gas content, gas remaining post-desorption, raw coal production, and mining influence coefficient. The case studies in Huaibei–Huainan Coalfield and Jincheng Coalfield show that the new method obtains the smallest error, + 9.59% and 7.01% respectively compared with other methods, Tier 1 and Tier 2 (with two samples) in this study, which resulted in + 140.34%, + 138.90%, and − 18.67%, in Huaibei–Huainan Coalfield, while + 64.36%, + 47.07%, and − 14.91% in Jincheng Coalfield. Compared with the predominantly used methods, this new one possesses the characteristics of not only being a comparably more simple process and lower uncertainty than the “emission factor method” (IPCC recommended Tier 1 and Tier 2), but also having easier data accessibility, similar uncertainty, and additional post-mining emissions compared to the “absolute gas emission method” (IPCC recommended Tier 3). Therefore, methane emissions dissipated from most of the producing coal mines worldwide could be more accurately and more easily estimated. - Highlights: • Propose a new method to estimate fugitive methane emissions from coal mining. • New method has accurate prediction for CMM emissions without activity data updating. • Mining

Correlation between Yellow Dust and Radioactivity

Energy Technology Data Exchange (ETDEWEB)

AIZaabia, Mouza A [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Kim, Byoung-Jik [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2015-10-15

In East Asia, yellow dust or Asian Dust (AD) outbreaks are among the largest contributors of wind-blown dust that carry natural and anthropogenic radionuclides and subsequently alter their concentration and distribution throughout the environment. Although the Korean Peninsula has been experiencing AD events since ancient times, the research has tended to focus on the transport routes and characteristics of AD, rather than on its impact on radionuclide activity levels. This paper examines the relationship between radionuclide concentration in the air and the frequency of dusty days in South Korea during AD intrusion events. It also investigates whether increased radionuclide concentration is a function of either more mass or more dust contamination. In this study, significant linear correlations of gamma-emitting radionuclides were found with mass of dust and occurrence frequency of AD. Regardless of the source origin of the dust, {sup 137}Cs and {sup 7}Be concentration primarily depended on dust mass in the filter. Nonetheless, the correlations were greatly distorted in 2011 and in the spring season, particularly the correlations with AD days that were far below that of the correlations obtained for the whole study period. A possible explanation of these conflicting results is that a change in the dust source could appreciably alter the concentration, deposition, and distribution of airborne radionuclides.

Road dust emission sources and assessment of street washing effect

NARCIS (Netherlands)

Karanasiou, A.; Amato, F.; Moreno, T.; Lumbreras, J.; Borge, R.; Linares, C.; Boldo, E.; Alastuey, A.; Querol, X.

2014-01-01

Although previous studies report on the effect of street washing on ambient particulate matter levels, there is a lack of studies investigating the results of street washing on the emission strength of road dust. A sampling campaign was conducted in Madrid urban area during July 2009 where road dust

Step by step in dust control

Energy Technology Data Exchange (ETDEWEB)

Archer, N. [Arch Environmental Equipment, Inc. (United States)

2003-05-01

The paper examines the different stages in identifying delegating and controlling dust before it becomes a serious problem for a facility. Material handling, processing, storage and traffic are the major dust producing sources. All industries that convey dry, light material need to install a dust control system. The confine-seal-suppress method of dust control has provided excellent results in numerous applications, only with the combination of all three will maximum dust control. When a system is properly engineered and correctly installed, meeting the EPA Government standards becomes very easy, and is necessary in to the operation of a quality facility. 5 photos.

CHARACTERIZATION OF FUGITIVE MERCURY EMISSIONS FROM THE CELL BUILDING AT A U.S. CHLOR-ALKALI PLANT

Science.gov (United States)

The paper discusses an extensive measurement campaign that was conducted of the fugitive (non-ducted) airborne elemental mercury [Hg(0)] emissions from the cell building of a chlor-alkali plant (CAP) located in the southeastern United States. The objectives of this study were to ...

Inventory of primary particulates emissions; Inventaire des emissions de particules primaires

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-12-01

CITEPA carried out a national inventory on particulate emissions. This report presents the results of this study for a great number of sectors and it covers a larger number of sources than the previous CITEPA inventories on particles and some other inventories carried out by International organisms (TNO, IIASA). In particular, at the present time, fugitive dust emissions for some sources are rarely taken into account in inventories because of poor knowledge and they are still the subject of researches in order to validate the emission results. (author)

78 FR 922 - Revisions to the California State Implementation Plan, Imperial County Air Pollution Control...

Science.gov (United States)

2013-01-07

...EPA is proposing to approve revisions to the Imperial County Air Pollution Control District (ICAPCD) portion of the California Implementation Plan (SIP). These revisions concern local rules that regulate inhalable particulate matter (PM10) emissions from sources of fugitive dust such as unpaved roads and disturbed soils in open and agricultural areas in Imperial County. We are proposing to approve local rules that regulate these emission sources under the Clean Air Act (CAA or the Act). We are taking comments on this proposal and plan to follow with a final action.

75 FR 13468 - Disapproval of California State Implementation Plan Revisions, Monterey Bay Unified Air Pollution...

Science.gov (United States)

2010-03-22

...EPA is proposing to disapprove a revision to the Monterey Bay Unified Air Pollution Control District (MBAPCD) portion of the California State Implementation Plan (SIP). This revision concerns opacity standards related to multiple pollutants, including particulate matter (PM) emissions from several different types of sources, ranging from fugitive dust to gas turbine generators. We are proposing action on a local rule that regulates these emission sources under the Clean Air Act as amended in 1990 (CAA or the Act). We are taking comments on this proposal and plan to follow with a final action.

Does the source migration pathway of HBCDs to household dust influence their bio-accessibility?

Energy Technology Data Exchange (ETDEWEB)

García-Alcega, Sonia [Soil Research Centre, University of Reading, Reading RG6 6AH (United Kingdom); Rauert, Cassie; Harrad, Stuart [School of Geography Earth and Environmental Sciences, University of Birmingham, Birmingham B15 2TT (United Kingdom); Collins, Chris D., E-mail: c.d.collins@reading.ac.uk [Soil Research Centre, University of Reading, Reading RG6 6AH (United Kingdom)

2016-11-01

A study was conducted to assess the human bioaccessibility of dust contaminated with hexabromocyclododecane (HBCD) via two migration pathways a) volatilisation with subsequent partitioning to dust particles, and b) abrasion of treated textile fibres directly to the dust. This was achieved using previously developed experimental chamber designs to generate dust samples contaminated with HBCDs emitted from a HBCD treated textile curtain. The generated dust samples were exposed to an in vitro colon extended physiologically based extraction test (CE-PBET). The bioaccessibility of the HBCDs which were incorporated within dust as a result of volatilisation from the curtain material with subsequent partitioning to dust was higher than in dusts contaminated with HBCDs via abrasion of the curtain (35% and 15% respectively). We propose this occurs due to a stronger binding of HBCDs to treated fabric fibres than that experienced following volatilisation and sorption of HBCDs to dust particles. - Highlights: • Migration pathways via which HBCDs enter dust influences its bioaccessibility. • HBCDs more bioaccessible when incorporated to dust via volatilisation. • Contamination of dusts is more variable via abrasion than volatilisation.

Does the source migration pathway of HBCDs to household dust influence their bio-accessibility?

International Nuclear Information System (INIS)

García-Alcega, Sonia; Rauert, Cassie; Harrad, Stuart; Collins, Chris D.

2016-01-01

A study was conducted to assess the human bioaccessibility of dust contaminated with hexabromocyclododecane (HBCD) via two migration pathways a) volatilisation with subsequent partitioning to dust particles, and b) abrasion of treated textile fibres directly to the dust. This was achieved using previously developed experimental chamber designs to generate dust samples contaminated with HBCDs emitted from a HBCD treated textile curtain. The generated dust samples were exposed to an in vitro colon extended physiologically based extraction test (CE-PBET). The bioaccessibility of the HBCDs which were incorporated within dust as a result of volatilisation from the curtain material with subsequent partitioning to dust was higher than in dusts contaminated with HBCDs via abrasion of the curtain (35% and 15% respectively). We propose this occurs due to a stronger binding of HBCDs to treated fabric fibres than that experienced following volatilisation and sorption of HBCDs to dust particles. - Highlights: • Migration pathways via which HBCDs enter dust influences its bioaccessibility. • HBCDs more bioaccessible when incorporated to dust via volatilisation. • Contamination of dusts is more variable via abrasion than volatilisation.

Fugitive emissions control on dry copper tailing with crushed rock armor

International Nuclear Information System (INIS)

Haase, E.F.

1992-01-01

Four inactive copper tailing impoundments totalling 1,900 acres near Ajo in southwestern Arizona were covered on horizontal surfaces with a 2 in. nominal thickness of crushed rock to control particulate emissions. The tailings are typically dominated by sand-sized particles but may also include significant PM 10 fractions towards the centers of the impoundments. The technology was selected by Phelps Dodge Corporation, after investigation of several alternatives, as a permanent and practical cover that essentially eliminates fugitive emissions. It simulates the natural desert pavement that characterizes this arid area of the Sonoran Desert. Rocky overburden was crushed to minus 3 in. diameter and broadcast on dry surfaces of tailing impoundments with all-terrain, balloon-tired spreaders. Stony residues in the rock armor tend to cement together following rainfall, forming a crust that enhances surface stability and erosion control. Slopes with windblown tailing deposition were covered to a nominal 6 in. thickness by conventional dozer pushing and blading of minus 10 in. rock over the sides. Athel trees, planted extensively since 1970 on two of the four inactive impoundments, provided partial control of fugitives, but were subjected to harsh environmental conditions, including abrasion from saltating particles. The rock armor functions as a mulch which is expected to improve water relations for existing vegetation and areas seeded with native species. New surface microenvironments, and the virtual elimination of surface creep and saltation, are expected to support native plant growth under favorable climatic conditions

Whither Cometary Dust?

Science.gov (United States)

Lisse, Carey M.

2010-10-01

In this paper I will discuss recent findings that have important implications for our understanding of the formation and evolution of primitive solar system dust, including: - Nesvorny et al. (2010), following up on their dynamical analyses of the zodiacal dust bands as sourced by the breakup of the Karin (5Mya) and Veritas (8Mya) asteroid families, argue that over 90% of the interplanetary dust cloud at 1 AU comes from JFC comets with near-circularized, low inclination orbits. This implies that the noted IPD collections of anhydrous and hydrous dust particles are likely to be from Oort cloud and JFC comets, respectively, not from asteroids and comets as thought in the past. Hydrous dust particles from comets like 85P/Wild2 and 9P/Tempel 1 would be consistent with results from the STARDUST and Deep Impact experiments. - Estimates of the dust particle size distributions (PSDs) in the comae of 85P/Wild2 (Green et al. 2004, 2007) and 73P/SW-3 (Sitko et al. 2010, Vaubaillon & Reach 2010) and in the trails of comets (Reach et al. 2007) have broken power law structure, with a plateau enhancement of particles of 1 mm - 1 cm in size. This size is also the size of most chondritic inclusions, and the predicted size range of the "aggregational barrier", where collisions between dust particles become destructive. - Studies of the albedo and polarization properties of cometary dust (Kolokolova et al. 2007) suggest there are 2 major groupings, one with low scattering capability and one with high. While these families could possibly have been explained by systematics in the PSDs of the emitted dust, independent work by Lisse et al. (2008) on the mineralogy of a number of highly dusty comets has shown evidence for one family of comets with highly crystalline dust and another with highly amorphous dust.

Identification of specific sources of airborne particles emitted from within a complex industrial (steelworks) site

Science.gov (United States)

Beddows, D. C. S.; Harrison, Roy M.

2018-06-01

A case study is provided of the development and application of methods to identify and quantify specific sources of emissions from within a large complex industrial site. Methods include directional analysis of concentrations, chemical source tracers and correlations with gaseous emissions. Extensive measurements of PM10, PM2.5, trace gases, particulate elements and single particle mass spectra were made at sites around the Port Talbot steelworks in 2012. By using wind direction data in conjunction with real-time or hourly-average pollutant concentration measurements, it has been possible to locate areas within the steelworks associated with enhanced pollutant emissions. Directional analysis highlights the Slag Handling area of the works as the most substantial source of elevated PM10 concentrations during the measurement period. Chemical analyses of air sampled from relevant wind directions is consistent with the anticipated composition of slags, as are single particle mass spectra. Elevated concentrations of PM10 are related to inverse distance from the Slag Handling area, and concentrations increase with increased wind speed, consistent with a wind-driven resuspension source. There also appears to be a lesser source associated with Sinter Plant emissions affecting PM10 concentrations at the Fire Station monitoring site. The results are compared with a ME2 study using some of the same data, and shown to give a clearer view of the location and characteristics of emission sources, including fugitive dusts.

Performance Evaluations and Quality Validation System for Optical Gas Imaging Cameras That Visualize Fugitive Hydrocarbon Gas Emissions

Science.gov (United States)

Optical gas imaging (OGI) cameras have the unique ability to exploit the electromagnetic properties of fugitive chemical vapors to make invisible gases visible. This ability is extremely useful for industrial facilities trying to mitigate product losses from escaping gas and fac...

An environmental pollution study of Indian metropolitan cities and industrial surroundings by INAA

International Nuclear Information System (INIS)

Garg, A.N.; Chutke, N.L.; Ambulkar, M.N.

1995-01-01

The process of urbanization and industrialization during last two decades has resulted in increased level of air pollution causing hazards to human health. Instrumental neutron activation analysis (INAA) using short and long term irradiation has been employed for the determination of more than 30 elements in suspended particulate matter (SPM) from six metropolitan cities and three industrial surroundings. A comparison of mean elemental contents in dust particulates from commercial, industrial and residential zones of Delhi, Calcutta, Madras, Cochin, Bombay and Nagpur cities has shown wide variation in toxic pollutant (As, Br, Cr, Cu, Hg and Sb) concentrations. Coastal areas have shown higher concentrations of Na, K, Cl and Br. Highly industrialized Bombay showed highest levels of Br, Cl, Cr, Fe, Mg, P, Rb and Sc. Mean elemental contents in fugitive and ambient dust of a cement factory and thermal power station (both in central India) are widely different. SPM levels in fugitive dust of the two industrial surroundings are higher by an order of magnitude compared to ambient air. Analysis of ambient air dust from a paper mill showed highest concentrations of Hg, Sb and Zn. Elemental data have been compared with those of Urban Particulate Matter (SRM 1648), Coal Fly Ash (SRM 1633a) and Vehicle Exhaust Particulate (NIES No. 8) which were analysed for quality control. An attempt has been made to attribute the elemental contents to possible sources of origin. (author) 26 refs.; 3 figs.; 3 tabs

The role of airborne mineral dusts in human disease

Science.gov (United States)

Morman, Suzette A.; Plumlee, Geoffrey S.

2013-01-01

Exposure to fine particulate matter (PM) is generally acknowledged to increase risk for human morbidity and mortality. However, particulate matter (PM) research has generally examined anthropogenic (industry and combustion by-products) sources with few studies considering contributions from geogenic PM (produced from the Earth by natural processes, e.g., volcanic ash, windborne ash from wildfires, and mineral dusts) or geoanthropogenic PM (produced from natural sources by processes that are modified or enhanced by human activities, e.g., dusts from lakebeds dried by human removal of water, dusts produced from areas that have undergone desertification as a result of human practices). Globally, public health concerns are mounting, related to potential increases in dust emission from climate related changes such as desertification and the associated long range as well as local health effects. Recent epidemiological studies have identified associations between far-traveled dusts from primary sources and increased morbidity and mortality in Europe and Asia. This paper provides an outline of public health research and history as it relates to naturally occurring inorganic mineral dusts. We summarize results of current public health research and describe some of the many challenges related to understanding health effects from exposures to dust aerosols.

Quasar Winds as Dust Factories at High Redshift

OpenAIRE

Elvis, Martin; Marengo, Massimo; Karovska, Margarita

2003-01-01

Winds from AGN and quasars will form large amounts of dust, as the cool gas in these winds passes through the (pressure, temperature) region where dust is formed in AGB stars. Conditions in the gas are benign to dust at these radii. As a result quasar winds may be a major source of dust at high redshifts, obviating a difficulty with current observations, and requiring far less dust to exist at early epochs.

Effects of Adding Corn Dried Distiller Grains with Solubles (DDGS to the Dairy Cow Diet and Effects of Bedding in Dairy Cow Slurry on Fugitive Methane Emissions

Directory of Open Access Journals (Sweden)

Daniel I. Massé

2014-12-01

Full Text Available The specific objectives of this experiment were to investigate the effects of adding 10% or 30% corn dried distillers grains with solubles (DDGS to the dairy cow diet and the effects of bedding type (wood shavings, straw or peat moss in dairy slurry on fugitive CH4 emissions. The addition of DDGS10 to the dairy cow diet significantly increased (29% the daily amount of fat excreted in slurry compared to the control diet. The inclusion of DDGS30 in the diet increased the daily amounts of excreted DM, volatile solids (VS, fat, neutral detergent fiber (NDF, acid detergent fiber (ADF and hemicellulose by 18%, 18%, 70%, 30%, 15% and 53%, respectively, compared to the control diet. During the storage experiment, daily fugitive CH4 emissions showed a significant increase of 15% (p < 0.05 for the slurry resulting from the corn DDGS30 diet. The addition of wood shavings and straw did not have a significant effect on daily fugitive CH4 emissions relative to the control diet, whereas the addition of peat moss caused a significant increase of 27% (p < 0.05 in fugitive CH4 emissions.

Effects of Adding Corn Dried Distiller Grains with Solubles (DDGS) to the Dairy Cow Diet and Effects of Bedding in Dairy Cow Slurry on Fugitive Methane Emissions.

Science.gov (United States)

Massé, Daniel I; Jarret, Guillaume; Benchaar, Chaouki; Hassanat, Fadi

2014-12-09

The specific objectives of this experiment were to investigate the effects of adding 10% or 30% corn dried distillers grains with solubles (DDGS) to the dairy cow diet and the effects of bedding type (wood shavings, straw or peat moss) in dairy slurry on fugitive CH₄ emissions. The addition of DDGS10 to the dairy cow diet significantly increased (29%) the daily amount of fat excreted in slurry compared to the control diet. The inclusion of DDGS30 in the diet increased the daily amounts of excreted DM, volatile solids (VS), fat, neutral detergent fiber (NDF), acid detergent fiber (ADF) and hemicellulose by 18%, 18%, 70%, 30%, 15% and 53%, respectively, compared to the control diet. During the storage experiment, daily fugitive CH₄ emissions showed a significant increase of 15% (p < 0.05) for the slurry resulting from the corn DDGS30 diet. The addition of wood shavings and straw did not have a significant effect on daily fugitive CH₄ emissions relative to the control diet, whereas the addition of peat moss caused a significant increase of 27% (p < 0.05) in fugitive CH₄ emissions.

Linear Alkylbenzenesulfonates in indoor Floor Dust

DEFF Research Database (Denmark)

Madsen, Jørgen Øgaard; Wolkoff, Peder; Madsen, Jørgen Øgaard

1999-01-01

The amount of Linear Alkylbenzenesulfonates (LAS) in the particle fraction of floor dust sampled from 7 selected public buildings varied between 34 and 1500 microgram per gram dust, while the contents of the fibre fractions generally were higher with up to 3500 microgram LAS/g dust. The use...... of a cleaning agent with LAS resulted in an increase of the amount of LAS in the floor dust after floor wash relative to just before floor wash. However, the most important source of LAS in the indoor floor dust appears to be residues of detergent in clothing. Thus, a newly washed shirt contained 2960 microgram...

Sr-Nd-Hf isotopic fingerprinting of transatlantic dust derived from North Africa

Science.gov (United States)

Zhao, Wancang; Balsam, William; Williams, Earle; Long, Xiaoyong; Ji, Junfeng

2018-03-01

Long-range transport of African dust plays an important role in understanding dust-climate relationships including dust source areas, dust pathways and associated atmospheric and/or oceanic processes. Clay-sized Sr-Nd-Hf isotopic compositions can be used as geochemical fingerprints to constrain dust provenance and the pathways of long-range transported mineral dust. We investigated the clay-sized Sr-Nd-Hf isotopic composition of surface samples along four transects bordering the Sahara Desert. The transects are from Mali, Niger/Benin/Togo, Egypt and Morocco. Our results show that the Mali transect on the West African Craton (WAC) produces lower εNd (εNd-mean = -16.38) and εHf (εHf-mean = -9.59) values than the other three transects. The Egyptian transect exhibits the lowest 87Sr/86Sr ratios (87Sr/86Srmean = 0.709842), the highest εHf (εHf-mean = -0.34) and εNd values of the four transects. Comparison of the clay-sized Sr-Nd-Hf isotopic values from our North African samples to transatlantic African dust collected in Barbados demonstrates that the dust's provenance is primarily the western Sahel and Sahara as well as the central Sahel. Summer emission dust is derived mainly from the western Sahel and Sahara regions. The source of transatlantic dust in spring and autumn is more varied than in the summer and includes dust not only from western areas, but also south central areas. Comparison of the Sr-Nd-Hf isotopic fingerprints between the source and sink of transatlantic dust also suggests that a northwestward shift in dust source occurs from the winter, through the spring and into the summer. The isotopic data we develop here provide another tool for discriminating changes in dust archives resulting from paleoenvironmental evolution of source regions.

Quantifying the environmental impact of particulate deposition from dry unpaved roadways

Energy Technology Data Exchange (ETDEWEB)

Becker, D.L.

1979-01-01

Airborne dust is the air pollutant most frequently observed to exceed National Ambient Air Quality Standards in rural areas. This pollutant (also referred to as suspended particulates) may originate from point sources (e.g., large areas of bare soil or pollen-producing vegetation.) Most sources of atmospheric particulates, whether natural or anthropogenic, are difficult to quantify by means of a source strength (i.e., mass of particulates emitted per unit time). A numerical model was developed for calculating the source strength and quantifying the atmospheric transport and eposition of dust generated on unpaved roadways. This model satisfies the second-order differential equation for the diffusion process and also the equation of mass conservation. Input to the model includes meterological variables, surface roughness characteristics, and the size distribution and suspended particulate concentration of dust as sampled downwind of an unpaved roadway. By using predetermined tolerance levels of airborne concentrations or tolerance levels of deposition, maximum allowable vehicular traffic volume can be established. The model also may be used to estimate reduction in photosynthesis resulting from fugitive dust from point or line sources. The contribug ion to sedimentation in aquatic bodies, resulting from airborne particulates also may be assessed with this model.

Environmental studies group. Annual report for 1978

International Nuclear Information System (INIS)

Hunt, D.C.; Hurley, J.D.

1980-01-01

Group projects included radioecological studies of aquatic and terrestrial systems, land management activities, foodstuff monitoring, dust transport studies including fugitive dust measurements and modeling, and several support programs involving evaluation of the plant's ambient air samplers and airborne tritium monitoring techniques. Some salient results from the several project reports include determination of an appropriate model for mechanically generated fugitive dust dispersion, a radionuclide inventory of Smart Ditch Pond (Pond D-1), a coefficient of community determination for two terrestrial sample plots on the plant site buffer zone, a natality and mortality rate determination for fawns in the plant deer herd (including one positive coyote-kill determination), inlet loss and filter paper collection efficiencies for the plant ambient air samplers, and differential tritium sampling measurements of the vapor in Building 771 stack effluent

Environmental studies group. Annual report for 1978

Energy Technology Data Exchange (ETDEWEB)

Hunt, D. C.; Hurley, J. D. [eds.

1980-08-21

Group projects included radioecological studies of aquatic and terrestrial systems, land management activities, foodstuff monitoring, dust transport studies including fugitive dust measurements and modeling, and several support programs involving evaluation of the plant's ambient air samplers and airborne tritium monitoring techniques. Some salient results from the several project reports include determination of an appropriate model for mechanically generated fugitive dust dispersion, a radionuclide inventory of Smart Ditch Pond (Pond D-1), a coefficient of community determination for two terrestrial sample plots on the plant site buffer zone, a natality and mortality rate determination for fawns in the plant deer herd (including one positive coyote-kill determination), inlet loss and filter paper collection efficiencies for the plant ambient air samplers, and differential tritium sampling measurements of the vapor in Building 771 stack effluent.

Investigation of dust storms entering Western Iran using remotely sensed data and synoptic analysis.

Science.gov (United States)

Boloorani, Ali D; Nabavi, Seyed O; Bahrami, Hosain A; Mirzapour, Fardin; Kavosi, Musa; Abasi, Esmail; Azizi, Rasoul

2014-01-01

One of the natural phenomena which have had considerable impacts on various regions of the world, including Iran, is "dust storm". In recent years, this phenomenon has taken on new dimensions in Iran and has changed from a local problem to a national issue. This study is an attempt to investigate the formation of the dust storms crossing the Western Iran. To find the sources of the dust storms entering Iran, first we examine three determined dust paths in the region and their temporal activities, using MODIS satellite images. Then, four regions were identified as dust sources through soil, land cover and wind data. Finally, atmospheric analyses are implemented to find synoptic patterns inducing dust storms. Source 1 has covered the region between the eastern banks of Euphrates and western banks of Tigris. Source 2 is in desert area of western and south-western Iraq. Finally source 3 is bounded in eastern and south-eastern deserts of Saudi Arabia called Rub-Al-Khali desert, or Empty Quarter. Moreover, south-eastern part of Iraq (source 4) was also determined as a secondary source which thickens the dust masses originating from the above mentioned sources. The study of synoptic circulations suggests that the dust storms originating from source 1 are formed due to the intense pressure gradient between the low-pressure system of Zagros and a high-pressure cell formed on Mediterranean Sea. The dust events in sources 2 and 3 are outcomes of the atmospheric circulations dominant in the cold period of the year in mid-latitudes.

Singlet Oxygen Production by Illuminated Road Dust and Winter Street Sweepings

Science.gov (United States)

Schneider, S.; Gan, L.; Gao, S.; Hoy, K. S.; Kwasny, J. R.; Styler, S. A.

2017-12-01

Road dust is an important urban source of primary particulate matter, especially in cities where sand and other traction materials are applied to roadways in winter. Although the composition and detrimental health effects of road dust are reasonably well characterized, little is currently known regarding its chemical behaviour. Motivated by our previous work, in which we showed that road dust is a photochemical source of singlet oxygen (1O2), we investigated 1O2 production by bulk winter street sweepings and by road dust collected in a variety of urban, industrial, and suburban locations in both autumn and spring. In all cases, the production of 1O2 by road dust was greater than that by Arizona test dust and desert-sourced dust, which highlights the unique photochemical environment afforded by this substrate. Mechanistically, we observed correlations between 1O2 production and the UV absorbance properties of dust extracts, which suggests the involvement of chromophoric dissolved organic matter in the observed photochemistry. Taken together, this work provides evidence that road dust-mediated photochemistry may influence the environmental lifetime of pollutants that react via 1O2-mediated pathways, including polycyclic aromatic hydrocarbons.

Fugitive methane emissions from natural, urban, agricultural, and energy-production landscapes of eastern Australia

Science.gov (United States)

Kelly, Bryce F. J.; Iverach, Charlotte P.; Lowry, Dave; Fisher, Rebecca E.; France, James L.; Nisbet, Euan G.

2015-04-01

Modern cavity ringdown spectroscopy systems (CRDS) enable the continuous measurement of methane concentration. This allows for improved quantification of greenhouse gas emissions associated with various natural and human landscapes. We present a subset of over 4000 km of continuous methane surveying along the east coast of Australia, made using a Picarro G2301 CRDS, deployed in a utility vehicle with an air inlet above the roof at 2.2 mAGL. Measurements were made every 5 seconds to a precision of cut coal mines, unconventional gas developments (coal seam gas; CSG), and leaks detected in cities and country towns. In areas of dryland crops the median methane concentration was 1.78 ppm, while in the irrigation districts located on vertisol soils the concentration was as low as 1.76 ppm, which may indicate that these soils are a sink for methane. In the Hunter Valley, New South Wales, open-cut coal mining district we mapped a continuous 50 km interval where the concentration of methane exceeded 1.80 ppm. The median concentration in this interval was 2.02 ppm. Peak readings were beyond the range of the reliable measurement (in excess of 3.00 ppm). This extended plume is an amalgamation of plumes from 17 major pits 1 to 10 km in length. Adjacent to CSG developments in the Surat Basin, southeast Queensland, only small anomalies were detected near the well-heads. Throughout the vast majority of the gas fields the concentration of methane was below 1.80 ppm. The largest source of fugitive methane associated with CSG was off-gassing methane from the co-produced water holding ponds. At one location the down wind plume had a cross section of approximately 1 km where the concentration of methane was above 1.80 ppm. The median concentration within this section was 1.82 ppm, with a peak reading of 2.11 ppm. The ambient air methane concentration was always higher in urban environments compared to the surrounding countryside. Along one major road in Sydney we mapped an interval

The Origin of Dust in the Early Universe

Science.gov (United States)

Dwek, Eli

2011-01-01

In this talk I will describe the origin of dust in the early universe. I will be presenting observations of the spectral energy distribution of the galaxy J1148+5251, and present estimates of the dust mass in this high redshift (z=6.4) object. I will then discuss the origin of this dust, and the role of SN and AGB stars as dust sources, and the effect of SNRs on the destruction of dust in the interstellar medium of this galaxy.

Grain size effect on Sr and Nd isotopic compositions in eolian dust. Implications for tracing dust provenance and Nd model age

International Nuclear Information System (INIS)

Feng Jinliang; Zhu Liping; Zhen Xiaolin; Hu Zhaoguo

2009-01-01

Strontium (Sr) and neodymium (Nd) isotopic compositions enable identification of dust sources and reconstruction of atmospheric dispersal pathways. The Sr and Nd isotopic compositions in eolian dust change systematically with grain size in ways not yet fully understood. This study demonstrates the grain size effect on the Sr and Nd isotopic compositions in loess and 2006 dust fall, based on analyses of seven separated grain size fractions. The analytical results indicate that Sr isotopic ratios strongly depend on the grain size fractions in samples from all types of eolian dust. In contrast, the Nd isotopic ratios exhibit little variation in loess, although they vary significantly with grain size in samples from a 2006 dust fall. Furthermore, Nd model ages tend to increase with increasing grain size in samples from all types of eolian dust. Comparatively, Sr isotopic compositions exhibit high sensitively to wind sorting, while Nd isotopic compositions show greater sensitively to dust origin. The principal cause for the different patterns of Sr and Nd isotopic composition variability with grain size appears related to the different geochemical behaviors between rubidium (Rb) and Sr, and the similar geochemical behaviors between samarium (Sm) and Nd. The Nd isotope data indicate that the various grain size fractions in loess have similar origins for each sample. In contrast, various provenance components may separate into different grain size fractions for the studied 2006 dust fall. The Sr and Nd isotope compositions further confirm that the 2006 dust fall and Pleistocene loess in Beijing have different sources. The loess deposits found in Beijing and those found on the Chinese Loess Plateau also derive from different sources. Variations between Sr and Nd isotopic compositions and Nd model ages with grain size need to be considered when directly comparing analyses of eolian dust of different grain size. (author)

Dust storm events over Delhi: verification of dust AOD forecasts with satellite and surface observations

Science.gov (United States)

Singh, Aditi; Iyengar, Gopal R.; George, John P.

2016-05-01

Thar desert located in northwest part of India is considered as one of the major dust source. Dust storms originate in Thar desert during pre-monsoon season, affects large part of Indo-Gangetic plains. High dust loading causes the deterioration of the ambient air quality and degradation in visibility. Present study focuses on the identification of dust events and verification of the forecast of dust events over Delhi and western part of IG Plains, during the pre-monsoon season of 2015. Three dust events have been identified over Delhi during the study period. For all the selected days, Terra-MODIS AOD at 550 nm are found close to 1.0, while AURA-OMI AI shows high values. Dust AOD forecasts from NCMRWF Unified Model (NCUM) for the three selected dust events are verified against satellite (MODIS) and ground based observations (AERONET). Comparison of observed AODs at 550 nm from MODIS with NCUM predicted AODs reveals that NCUM is able to predict the spatial and temporal distribution of dust AOD, in these cases. Good correlation (~0.67) is obtained between the NCUM predicted dust AODs and location specific observations available from AERONET. Model under-predicted the AODs as compared to the AERONET observations. This may be mainly because the model account for only dust and no anthropogenic activities are considered. The results of the present study emphasize the requirement of more realistic representation of local dust emission in the model both of natural and anthropogenic origin, to improve the forecast of dust from NCUM during the dust events.

Reconstructing transport pathways for late Quaternary dust from eastern Australia using the composition of trace elements of long traveled dusts

Science.gov (United States)

Petherick, Lynda M.; McGowan, Hamish A.; Kamber, Balz S.

2009-04-01

The southeast Australian dust transport corridor is the principal pathway through which continental emissions of dust from central and eastern Australia are carried to the oceans by the prevailing mid-latitude westerly circulation. The analysis of trace elements of aeolian dust, preserved in lake sediment on North Stradbroke Island, southeast Queensland, is used to reconstruct variation in the intensity and position of dust transport to the island over the past 25,000 yrs. Separation of local and long traveled dust content of lake sediments is achieved using a unique, four-element (Ga, Ni, Tl and Sc) separation method. The local and continental chronologies of aeolian deposition developed by this study show markedly different records, and indicate varied responses to climate variability on North Stradbroke Island (local aeolian sediment component) and in eastern and central Australia (long traveled dust component). The provenance of the continental component of the record to sub-geologic catchment scales was accomplished using a ternary mixing model in which the chemical identification of dusts extracted, from the lake sediments, was compared to potential chemical characteristics of surface dust from the source areas using 16 trace elements. The results indicate that the position and intensity of dust transport pathways during the late Quaternary varied considerably in response to changing atmospheric circulation patterns as well as to variations in sediment supply to dust source areas, which include the large anabranching river systems of the Lake Eyre and Murray-Darling Basins.

The ecological risk, source identification, and pollution assessment of heavy metals in road dust: a case study in Rafsanjan, SE Iran.

Science.gov (United States)

Mirzaei Aminiyan, Milad; Baalousha, Mohammed; Mousavi, Rouhollah; Mirzaei Aminiyan, Farzad; Hosseini, Hamideh; Heydariyan, Amin

2018-05-01

Heavy metal (HM) contamination in road dust is a potential environmental and human health threat. The sources, concentrations, spatial distribution, and ecological risk of As, Cd, Cu, Cr, Ni, Pb, and Zn in road dust in Rafsanjan City, Iran, were investigated. Pollution was assessed using the enrichment factor (EF). The potentially harmful effects of HMs were evaluated by calculating the potential ecological risk factor of individual metals (E r ) and of multiple metals (RI) using the Hakanson method. Correlation and principal component analyses (PCA) were applied to identify HM pollution sources. The concentrations of HMs in road dust were higher (ca. 5-10 folds) than their natural background values. The EF and E r increased according to the following order Cu > Pb > As > Zn > Cd > Cr > Ni and Cu > Cd > Pb > As > Ni > Zn > Cr, respectively. Thus, Cu is regarded as the pollutant of highest concern. Based on potential ecological risk index (RI) spatial distribution, all parts of Rafsanjan are characterized by significantly high potential ecological risk. HM concentration heat maps, PCA, and correlation analysis suggest that Cu, Pb, As, Cd, and Zn may have originated from the same source and follow the same spatial distribution pattern. These metals originated mainly from anthropogenic sources like copper mining and smelting plants, industrial and chemical activities, inordinate application of chemical fertilizers and pesticides in farmlands, and heavy traffic. Ni and Cr are likely to origniate from the industrial activities and traffic load in Rafsanjan City.

Is Optical Gas Imaging Effective for Detecting Fugitive Methane Emissions? - A Technological and Policy Perspective

Science.gov (United States)

Ravikumar, A. P.; Wang, J.; Brandt, A. R.

2016-12-01

Mitigating fugitive methane emissions from the oil and gas industry has become an important concern for both businesses and regulators. While recent studies have improved our understanding of emissions from all sectors of the natural gas supply chain, cost-effectively identifying leaks over expansive natural gas infrastructure remains a significant challenge. Recently, the Environmental Protection Agency (EPA) has recommended the use of optical gas imaging (OGI) technologies to be used in industry-wide leak detection and repair (LDAR) programs. However, there has been little to no systematic study of the effectiveness of infrared-camera-based OGI technology for leak detection applications. Here, we develop a physics-based model that simulates a passive infrared camera imaging a methane leak against varying background and ambient conditions. We verify the simulation tool through a series of large-volume controlled release field experiments wherein known quantities of methane were released and imaged from a range of distances. After simulator verification, we analyze the effects of environmental conditions like temperature, wind, and imaging background on the amount of methane detected from a statistically representative survey program. We also examine the effects of LDAR design parameters like imaging distance, leak size distribution, and gas composition. We show that imaging distance strongly affects leak detection - EPA's expectation of a 60% reduction in fugitive emissions based on a semi-annual LDAR survey will be realized only if leaks are imaged at a distance less than 10 m from the source under ideal environmental conditions. Local wind speed is also shown to be important. We show that minimum detection limits are 3 to 4 times higher for wet-gas compositions that contain a significant fraction of ethane and propane, resulting a significantly large leakage rate. We also explore the importance of `super-emitters' on the performance of an OGI-based leak

Identification of historical lead sources in roof dust and recent lake sediments from an industrialized are: Indications from lead isotopes

International Nuclear Information System (INIS)

Chenhall, B.E.; Depers, A.M.; Jones, B.G.; Chiaradia, M.

1997-01-01

X-ray fluorescence and stable lead (Pb) isotopic analyses have been undertaken on dusts, known from microscopic investigation to contain significant quantities of industrially- and urban-derived particulate matter, present in the roof cavities of houses in the Illawarra region (N.S.W., Australia), with the objective of examining the historic record of Pb pollution. All investigated houses contained in excess of 250 μg g -1 Pb, with dwellings close to a copper smelter, in a large industrial complex including a major steelworks, containing higher (>2500 μg g -1 ) Pb concentrations. The isotopic composition in the dusts, expressed here as 206 Pb/ 204 Pb, is relatively constant at 17.0, irrespective of dwelling age or distance from the industrial complex. Contamination of the dusts by Pb sourced from paint cannot explain the isotopic uniformity of the dust samples. Isotopic modelling indicates that the dusts contain Pb derived from the copper smelter, gasoline-air Pb and a minor contribution from the steelworks. Isotopic calculations, together with records of particulate pollution emission, indicate a link between the Pb in roof dusts and Pb contamination of the near surface lagoonal sediments. Over the last five decades, atmospheric fallout of Pb-bearing particulate matter appears to have been the dominant pathway for addition of Pb to the lagoon and dwellings in the Illawarra region

DISCOVERY OF 'WARM DUST' GALAXIES IN CLUSTERS AT z {approx} 0.3: EVIDENCE FOR STRIPPING OF COOL DUST IN THE DENSE ENVIRONMENT?

Energy Technology Data Exchange (ETDEWEB)

Rawle, T. D.; Rex, M.; Egami, E.; Walth, G.; Pereira, M. J. [Steward Observatory, University of Arizona, 933 N. Cherry Avenue, Tucson, AZ 85721 (United States); Chung, S. M.; Gonzalez, A. H. [Department of Astronomy, University of Florida, Gainesville, FL 32611-2055 (United States); Perez-Gonzalez, P. G. [Departamento de Astrofisica, Facultad de CC. Fisicas,Universidad Complutense de Madrid, E-28040 Madrid (Spain); Smail, I. [Institute for Computational Cosmology, Durham University, South Road, Durham DH1 3LE (United Kingdom); Altieri, B.; Valtchanov, I. [Herschel Science Centre, ESAC, ESA, P.O. Box 78, Villanueva de la Canada, E-28691 Madrid (Spain); Appleton, P.; Fadda, D. [IPAC, California Institute of Technology, Pasadena, CA 91125 (United States); Alba, A. Berciano [ASTRON, Oude Hoogeveensedijk 4, NL-7991 PD Dwingeloo (Netherlands); Blain, A. W. [Department of Physics and Astronomy, University of Leicester, University Road, Leicester LE1 7RH (United Kingdom); Dessauges-Zavadsky, M. [Observatoire de Geneve, Universite de Geneve, 51 Ch. des Maillettes, CH-1290 Sauverny (Switzerland); Van der Werf, P. P. [Sterrewacht Leiden, Leiden University, P.O. Box 9513, NL-2300 RA Leiden (Netherlands); Zemcov, M., E-mail: trawle@as.arizona.edu [Department of Physics, Mathematics and Astronomy, California Institute of Technology, Pasadena, CA 91125 (United States)

2012-09-10

Using far-infrared imaging from the 'Herschel Lensing Survey', we derive dust properties of spectroscopically confirmed cluster member galaxies within two massive systems at z {approx} 0.3: the merging Bullet Cluster and the more relaxed MS2137.3-2353. Most star-forming cluster sources ({approx}90%) have characteristic dust temperatures similar to local field galaxies of comparable infrared (IR) luminosity (T{sub dust} {approx} 30 K). Several sub-luminous infrared galaxy (LIRG; L{sub IR} < 10{sup 11} L{sub Sun }) Bullet Cluster members are much warmer (T{sub dust} > 37 K) with far-infrared spectral energy distribution (SED) shapes resembling LIRG-type local templates. X-ray and mid-infrared data suggest that obscured active galactic nuclei do not contribute significantly to the infrared flux of these 'warm dust' galaxies. Sources of comparable IR luminosity and dust temperature are not observed in the relaxed cluster MS2137, although the significance is too low to speculate on an origin involving recent cluster merging. 'Warm dust' galaxies are, however, statistically rarer in field samples (>3{sigma}), indicating that the responsible mechanism may relate to the dense environment. The spatial distribution of these sources is similar to the whole far-infrared bright population, i.e., preferentially located in the cluster periphery, although the galaxy hosts tend toward lower stellar masses (M{sub *} < 10{sup 10} M{sub Sun }). We propose dust stripping and heating processes which could be responsible for the unusually warm characteristic dust temperatures. A normal star-forming galaxy would need 30%-50% of its dust removed (preferentially stripped from the outer reaches, where dust is typically cooler) to recover an SED similar to a 'warm dust' galaxy. These progenitors would not require a higher IR luminosity or dust mass than the currently observed normal star-forming population.

Laboratory study of PCB transport from primary sources to settled dust

Science.gov (United States)

Transport of house dust and Arizona Test Dust on polychlorinated biphenyl (PCB)-containing panels and PCB-free panels was investigated in a 30-m3 stainless steel chamber. The PCB-containing panels were aluminum sheets coated with a PCB-spiked, oil-based primer or two-part polysul...

Dust from southern Africa: rates of emission and biogeochemical properties

Science.gov (United States)

Bhattachan, A.; D'Odorico, P.; Zobeck, T. M.; Okin, G. S.; Dintwe, K.

2012-12-01

The stabilized linear dunefields in the southern Kalahari show signs of reactivation due to reduced vegetation cover owing to drought and/or overgrazing. It has been demonstrated with a laboratory dust generator that the southern Kalahari soils are good emitters of dust and that large-scale dune reactivation can potentially make the region an important dust source in the relatively low-dust Southern Hemisphere. We show that emergence of the southern Kalahari as a new dust source may affect ocean biogeochemistry as the soils are rich in soluble iron and the dust from the southern Kalahari commonly reaches the Southern Ocean. We investigate the biogeochemical properties of the fine fraction of soil from the Kalahari dunes and compare them to those of currently active dust sources such as the Makgadikgadi and the Etosha pans as well as other smaller pans in the region. Using field measurements of sediment fluxes and satellite images, we calculate the rates of dust emission from the southern Kalahari under different land cover scenarios. To assess the reversibility of dune reactivation in the southern Kalahari, we investigate the resilience of dunefield vegetation by looking at changes in soil nutrients, fine soil fractions, and seed bank in areas affected by intense denudation.

Lead in Chinese villager house dust: Geographical variation and influencing factors

International Nuclear Information System (INIS)

Bi, Xiangyang; Liu, Jinling; Han, Zhixuan; Yang, Wenlin

2015-01-01

House dust has been recognized as an important contributor to Pb exposure of children. Here we conducted a comprehensive study to investigate geographical variation of Pb in Chinese villager house dust. The influences of outdoor soil Pb concentrations, dates of construction, house decoration materials, heating types, and site specific pollution on Pb concentrations in house dust were evaluated. The concentrations of Pb in 477 house dust samples collected from twenty eight areas throughout China varied from 12 to 2510 mg/kg, with a median concentration of 42 mg/kg. The median Pb concentrations in different geographical areas ranged from 16 (Zhangjiakou, Hebei) to 195 mg/kg (Loudi, Hunan). No correlations were found between the house dust Pb concentrations and the age of houses, as well as house decoration materials. Whereas outdoor soil, coal combustion, and site specific pollution may be potential Pb sources. Principal component analysis (PCA) confirmed that elemental compositions of the house dust were controlled by both anthropogenic and geogenic sources. Using scanning electron microscopy (SEM), the Pb bearing particles in the house dust were also studied. - Highlights: • Geographical variation in house dust Pb concentrations were observed. • Dust Pb concentrations were not associated with house age and decoration materials. • Soil, coal combustion, and site specific pollution were potential Pb sources. • Pb bearing particles were identified by SEM-EDX. - The variations of Pb in Chinese villager house dust were controlled by outdoor soil, coal combustion, and site specific pollution sources.

Characterization of Dust Properties Near Source Region During ACE-Asia: A Column Satellite-Surface Perspective

Science.gov (United States)

Tsay, S. -C.; Ji, Q.; Chu, A.; Hsu, C.; Holben, B.; Campbell, J.; Welton, E. J.; Shu, P. K.

2002-01-01

Many recent field experiments are designed to study the compelling variability in spatial and temporal scale of both pollution-derived and naturally occurring aerosols, which often exist in high concentrations over eastern/southeastern Asia and along the rim of the western Pacific. For example, the ACE-Asia was conducted from March-May 2001 in the vicinity of the Taklimakan and Gobi deserts, East Coast of China, Yellow Sea, Korea, and Japan, along the pathway of Kosa (severe events that blanket East Asia with yellow desert dust, peaked in the Spring season). Asian dust typically originates in desert areas far from polluted urban regions. During transport, dust layers can interact with anthropogenic sulfate and soot aerosols from heavily polluted urban areas. Added to the complex effects of clouds and natural marine aerosols, dust particles reaching the marine environment can have drastically different properties than those from the source. Thus, understanding the unique temporal and spatial variations of Asian aerosols is of special importance in regional-to-global climate issues such as radiative forcing, the hydrological cycle, and primary biological productivity in the mid-Pacific Ocean. During ACE-Asia we have measured continuously aerosol physical/optical/radiative properties, column precipitable water amount, and surface reflectivity over homogeneous areas from surface. The inclusion of flux measurements permits the determination of aerosol radiative flux in addition to measurements of loading and optical depth. At the time of the Terra/MODIS, SeaWiFS, TOMS and other satellite overpasses, these ground-based observations can provide valuable data to compare with satellite retrievals over land. Preliminary results will be presented and discussed their implications in regional climatic effects.

Enhancement and identification of dust events in the south-west ...

Indian Academy of Sciences (India)

in dust source regions, which have a negative impact on human health ... Keywords. MODIS; dust storm; visible; infrared; remote sensing; brightness temperature. 1 ... clouds can often be misinterpreted as dust. In order to ... dust aerosol outbreaks over land using satellite ... models were also used to track air parcels arriving.

High Proportions of Sub-micron Particulate Matter in Icelandic Dust Storms in 2015

Science.gov (United States)

Dagsson Waldhauserova, Pavla; Arnalds, Olafur; Olafsson, Haraldur; Magnusdottir, Agnes

2017-04-01

Iceland is extremely active dust region and desert areas of over 44,000 km2 acknowledge Iceland as the largest Arctic and European desert. Frequent dust events, up to 135 dust days annually, transport dust particles far distances towards the Arctic and Europe. Satellite MODIS pictures have revealed dust plumes exceeding 1,000 km. The annual dust deposition was calculated as 40.1 million tons yr-1. Two dust storms were measured in transverse horizontal profile about 90 km far from different dust sources in southwestern Iceland in the summer of 2015. Aerosol monitor DustTrak DRX 8533EP was used to measure PM mass concentrations corresponding to PM1, PM2.5, PM4, PM10 and the total PM15 at several places within the dust plume. Images from camera network operated by the Icelandic Road and Coastal Administration were used to estimate the visibility and spatial extent of measured dust events. A numerical simulation of surface winds was carried out with the numerical model HIRLAM with horizontal resolution of 5 km and used to calculate the total dust flux from the sources. The in situ measurements inside the dust plumes showed that aeolian dust can be very fine. The study highlights that suspended volcanic dust in Iceland causes air pollution with extremely high PM1 concentrations comparable to the polluted urban stations in Europe or Asia rather than reported dust event observations from around the world. The PM1/PM2.5 ratios are generally low during dust storms outside of Iceland, much lower than > 0.9 and PM1/PM10 ratios of 0.34-0.63 found in our study. It shows that Icelandic volcanic dust consists of higher proportion of submicron particles compared to crustal dust. The submicron particles are predicted to travel long distances. Moreover, such submicron particles pose considerable health risk because of high potential for entering the lungs. Icelandic volcanic glass has often fine pipe-vesicular structures known from asbestos and high content of heavy metals. Previous

Chemical signatures of urban, open burning and dust transportation in an urban environment- megacity in South Asia

Science.gov (United States)

Priyadharshini, B.; Verma, S.

2016-12-01

A sub-micron aerosol sampler (SAS) consisting of two parallel stacked filter units (SFU) was deployed at an urban location (Kolkata) to study the sub-micron aerosols (water soluble inorganic ions (WSII) and carbonaceous aerosols (elemental carbon (EC) and organic carbon (OC)) collected over a year (September 2010 to August 2011). Quantification of 10 WSII species using Ion Chromatograph (IC) indicated alkaline nature of aerosols with calcium (Ca2+) being the major neutralizing factor of acidity at the study site. In terms of WSII percentage contribution, the most abundant were crustal species (Ca2+, magnesium (Mg2+) and marine species (chloride (Cl-)), followed by the secondary species sulphate (SO42-), nitrate (NO3-) and ammonium (NH4+) . Ca2+ (fugitive and transported dust) was dominant throughout the study period with K+ concentrations exhibiting seasonality with agricultural residue burning. Further, results of carbonaceous aerosols analyzed using the OC-EC aerosol analyzer following Interagency Monitoring of Protected Visual Environment (IMPROVE) protocol exhibited pronounced seasonality in OC than EC with the overall mean concentration of OC being three folds than EC. Primary organic carbon (POC) and secondary organic carbon concentrations (SOC) estimated using EC tracer method showed 57% (43%) of POC (SOC) from various emission sources. Investigation of OC/EC ratio along with non-sea salt potassium (nss-K+) values revealed influence of season specific anthropogenic activities on both OC and EC concentrations (viz. Open burning (OB)) besides fossil fuel (FF) and biofuel (BF) usage for cooking and heating prevalent over the region. Source apportionment was discerned using positive matrix factorization (PMF) with four major factors (crustal, agricultural, anthropogenic sources and mixed source (crustal + agriculture + anthropogenic) as the primary contributors to the sub-micron aerosols at the study site.

Long-term variability of dust-storms in Iceland

Science.gov (United States)

Dagsson-Waldhauserová, Pavla; Ólafsson, Haraldur; Arnalds, Ólafur

2013-04-01

Iceland is a volcanic island in the North Atlantic Ocean with maritime climate. In spite of moist climate, large areas are with limited vegetation cover where >40% of Iceland is classified with considerable to very severe erosion and 21% of Iceland are volcanic sandy deserts. Natural emissions from these sources influenced by strong winds affect not only regional air quality in Iceland ("Reykjavik haze") but dust particles are transported over the Atlantic ocean and Arctic Ocean > 1000 km at times. The study places Icelandic dust production area into international perspective, present long term frequency of dust storm events in NE Iceland, and estimate dust aerosol concentrations during reported dust events. Meteorological observations with dust presence codes and related visibility were used to identify the frequency and the long-term changes in dust production in NE Iceland. There were annually 16.4 days on average with reported dust observations on weather stations within the NE erosion area, indicating extreme dust plume activity and erosion within the NE deserts, even though the area is covered with snow during the major part of winter. During the 2000s the highest occurrence of dust events in six decades was reported. We have measured saltation and aeolian transport during dust/volcanic ash storms in Iceland which give some of the most intense wind erosion events ever measured. Icelandic dust affects the ecosystems over much of Iceland and causes regional haze. It is likely to affect the ecosystems of the oceans around Iceland, and it brings dust that lowers the albedo of the Icelandic glaciers, increasing melt-off due to global warming. The study indicates that Icelandic dust is not only a substantial source for regional air pollution, but may be considered to contribute to the Arctic haze phenomena and Arctic air pollution.

Surface observation of sand and dust storm in East Asia and its application in CUACE/Dust

Directory of Open Access Journals (Sweden)

Y. Q. Wang

2008-02-01

Full Text Available The spatial-temporal distributions and sources of sand and dust storm (SDS in East Asia from 2001 to 2006 were investigated on the basis of visibility and PM₁₀ data from the routine SDS and weather monitoring networks run by CMA (China Meteorological Administration. A power functional relationships between PM₁₀ and visibility was found among various regions generally with a good correlation (r²=0.90, especially in Asian SDS source regions. In addition, three SDS occurrence centers, i.e. western China, Mongolia and northern China, were identified with the Mongolia source contributing more dust to the downwind areas including Korea and Japan than other two sources. Generally, high PM₁₀ concentrations were observed in most areas of northern China. The highest value was obtained in the center of western China with a spring daily mean value of 876 μgm⁻³, and the value in other source regions exceeds 200 μgm⁻³. These data sets together with the satellite observations in China form the main observation database for the evaluation and data assimilation of CUACE/Dust system – an operational SDS forecasting system for East Asia.

Polycyclic aromatic hydrocarbons (PAHs in indoor dusts of Guizhou, southwest of China: status, sources and potential human health risk.

Directory of Open Access Journals (Sweden)

Qin Yang

Full Text Available Polycyclic aromatic hydrocarbons (PAHs were analyzed for 136 indoor dust samples collected from Guizhou province, southwest of China. The ∑18PAHs concentrations ranged from 2.18 μg•g-1 to 14.20 μg•g-1 with the mean value of 6.78 μg•g-1. The highest Σ18PAHs concentration was found in dust samples from orefields, followed by city, town and village. Moreover, the mean concentration of Σ18PAHs in indoor dust was at least 10% higher than that of outdoors. The 4-6 rings PAHs, contributing more than 70% of ∑18PAHs, were the dominant species. PAHs ratios, principal component analysis with multiple linear regression (PCA-MLR and hierarchical clustering analysis (HCA were applied to evaluate the possible sources. Two major origins of PAHs in indoor dust were identified as vehicle emissions and coal combustion. The mean incremental lifetime cancer risk (ILCR due to human exposure to indoor dust PAHs in city, town, village and orefield of Guizhou province, China was 6.14×10-6, 5.00×10-6, 3.08×10-6, 6.02×10-6 for children and 5.92×10-6, 4.83×10-6, 2.97×10-6, 5.81×10-6 for adults, respectively.

Dust grains from the heart of supernovae

Science.gov (United States)

Bocchio, M.; Marassi, S.; Schneider, R.; Bianchi, S.; Limongi, M.; Chieffi, A.

2016-03-01

Dust grains are classically thought to form in the winds of asymptotic giant branch (AGB) stars. However, there is increasing evidence today for dust formation in supernovae (SNe). To establish the relative importance of these two classes of stellar sources of dust, it is important to know the fraction of freshly formed dust in SN ejecta that is able to survive the passage of the reverse shock and be injected in the interstellar medium. With this aim, we have developed a new code, GRASH_Rev, that allows following the dynamics of dust grains in the shocked SN ejecta and computing the time evolution of the mass, composition, and size distribution of the grains. We considered four well-studied SNe in the Milky Way and Large Magellanic Cloud: SN 1987A, CasA, the Crab nebula, and N49. These sources have been observed with both Spitzer and Herschel, and the multiwavelength data allow a better assessment the mass of warm and cold dust associated with the ejecta. For each SN, we first identified the best explosion model, using the mass and metallicity of the progenitor star, the mass of 56Ni, the explosion energy, and the circumstellar medium density inferred from the data. We then ran a recently developed dust formation model to compute the properties of freshly formed dust. Starting from these input models, GRASH_Rev self-consistently follows the dynamics of the grains, considering the effects of the forward and reverse shock, and allows predicting the time evolution of the dust mass, composition, and size distribution in the shocked and unshocked regions of the ejecta. All the simulated models aagree well with observations. Our study suggests that SN 1987A is too young for the reverse shock to have affected the dust mass. Hence the observed dust mass of 0.7-0.9 M⊙ in this source can be safely considered as indicative of the mass of freshly formed dust in SN ejecta. Conversely, in the other three SNe, the reverse shock has already destroyed between 10-40% of the

Regional and climatic controls on seasonal dust deposition in the southwestern U.S.

Science.gov (United States)

Reheis, M.C.; Urban, F.E.

2011-01-01

Vertical dust deposition rates (dust flux) are a complex response to the interaction of seasonal precipitation, wind, changes in plant cover and land use, dust source type, and local vs. distant dust emission in the southwestern U.S. Seasonal dust flux in the Mojave-southern Great Basin (MSGB) deserts, measured from 1999 to 2008, is similar in summer-fall and winter-spring, and antecedent precipitation tends to suppress dust flux in winter-spring. In contrast, dust flux in the eastern Colorado Plateau (ECP) region is much larger in summer-fall than in winter-spring, and twice as large as in the MSGB. ECP dust is related to wind speed, and in the winter-spring to antecedent moisture. Higher summer dust flux in the ECP is likely due to gustier winds and runoff during monsoonal storms when temperature is also higher. Source types in the MSGB and land use in the ECP have important effects on seasonal dust flux. In the MSGB, wet playas produce salt-rich dust during wetter seasons, whereas antecedent and current moisture suppress dust emission from alluvial and dry-playa sources during winter-spring. In the ECP under drought conditions, dust flux at a grazed-and-plowed site increased greatly, and also increased at three annualized, previously grazed sites. Dust fluxes remained relatively consistent at ungrazed and currently grazed sites that have maintained perennial vegetation cover. Under predicted scenarios of future climate change, these results suggest that an increase in summer storms may increase dust flux in both areas, but resultant effects will depend on source type, land use, and vegetation cover. ?? 2011.

PAEs occurrence and sources in road dust and soil in/around parks in May in Tianjin, China.

Science.gov (United States)

Zhao, Jie; Ji, Yaqin; Zhu, Zhenyu; Zhang, Wei; Zhang, Lei; Zhao, Jingbo

2018-01-01

This is the first study reporting the presence of six phthalic acid esters (PAEs) in 45 composite soil and road dust samples collected in the urban zone of Tianjin, China. Three sample types (one soil and two road dust) were collected from the city parks. Soil samples (SI) were obtained from inside the park, road dust samples (RDI) were gathered from inside the park roads and the others (RDA) from roads surrounding parks. The range of concentrations of ∑ 6 PAEs in SI, RDI and RDA were 0.07-0.92μgg -1 , 0.42-6.32μgg -1 and 0.40-7.54μgg -1 , respectively. The highest SI ∑ 6 PAEs concentration (0.92μgg -1 in The People's Park) was 13 times higher than that of the lowest content (0.07μgg -1 in XiLiu Park). Furthermore, the spatial distribution of PAEs in RDI showed higher contents in the Nankai and Hexi districts. PAEs concentrations in different types of roads displayed significant differences (P roads such as arterial road > sub-arterial road > branch road. The results of nonparametric tests on ∑ 6 PAEs revealed significant differences between every two different sample types (P < 0.05). The analysis of the six PAEs types indicated DnBP and DEHP were the primary contaminating compounds in all sample types. The PCA results showed cosmetics and personal care products were important sources of PAEs in SI, and plasticizers were the key sources of PAEs in RDI and RDA. Copyright © 2017 Elsevier Inc. All rights reserved.

Phosphorus speciation and solubility in aeolian dust deposited in the interior American West

Science.gov (United States)

Zhang, Zhuojun; Goldstein, Harland L.; Reynolds, Richard L.; Hu, Yongfeng; Wang, Xiaoming; Zhu, Mengqiang

2018-01-01

Aeolian dust is a significant source of phosphorus (P) to alpine oligotrophic lakes, but P speciation in dust and source sediments and its release kinetics to lake water remain unknown. Phosphorus K-edge XANES spectroscopy shows that calcium-bound P (Ca−P) is dominant in 10 of 12 dust samples (41−74%) deposited on snow in the central Rocky Mountains and all 42 source sediment samples (the fine fraction) (68−80%), with a lower proportion in dust probably because acidic snowmelt dissolves some Ca−P in dust before collection. Iron-bound P (Fe−P, ∼54%) dominates in the remaining two dust samples. Chemical extractions (SEDEX) on these samples provide inaccurate results because of unselective extraction of targeted species and

Dust: Small-scale processes with global consequences

Science.gov (United States)

Okin, G.S.; Bullard, J.E.; Reynolds, R.L.; Ballantine, J.-A.C.; Schepanski, K.; Todd, M.C.; Belnap, J.; Baddock, M.C.; Gill, T.E.; Miller, M.E.

2011-01-01

Desert dust, both modern and ancient, is a critical component of the Earth system. Atmospheric dust has important effects on climate by changing the atmospheric radiation budget, while deposited dust influences biogeochemical cycles in the oceans and on land. Dust deposited on snow and ice decreases its albedo, allowing more light to be trapped at the surface, thus increasing the rate of melt and influencing energy budgets and river discharge. In the human realm, dust contributes to the transport of allergens and pathogens and when inhaled can cause or aggravate respiratory diseases. Dust storms also represent a significant hazard to road and air travel. Because it affects so many Earth processes, dust is studied from a variety of perspectives and at multiple scales, with various disciplines examining emissions for different purposes using disparate strategies. Thus, the range of objectives in studying dust, as well as experimental approaches and results, has not yet been systematically integrated. Key research questions surrounding the production and sources of dust could benefit from improved collaboration among different research communities. These questions involve the origins of dust, factors that influence dust production and emission, and methods through which dust can be monitored. ?? Author(s) 2011.

Experiments on Dust Grain Charging

Science.gov (United States)

Abbas, M. N.; Craven, P. D.; Spann, J. F.; Tankosic, D.; LeClair, A.; West, E. A.

2004-01-01

Dust particles in various astrophysical environments are charged by a variety of mechanisms generally involving collisional processes with other charged particles and photoelectric emission with UV radiation from nearby sources. The sign and the magnitude of the particle charge are determined by the competition between the charging processes by UV radiation and collisions with charged particles. Knowledge of the particle charges and equilibrium potentials is important for understanding of a number of physical processes. The charge of a dust grain is thus a fundamental parameter that influences the physics of dusty plasmas, processes in the interplanetary medium and interstellar medium, interstellar dust clouds, planetary rings, cometary and outer atmospheres of planets etc. In this paper we present some results of experiments on charging of dust grains carried out on a laboratory facility capable levitating micron size dust grains in an electrodynamic balance in simulated space environments. The charging/discharging experiments were carried out by exposing the dust grains to energetic electron beams and UV radiation. Photoelectric efficiencies and yields of micron size dust grains of SiO2, and lunar simulates obtained from NASA-JSC will be presented.

Ulysses dust measurements near Jupiter.

Science.gov (United States)

Grün, E; Zook, H A; Baguhl, M; Fechtig, H; Hanner, M S; Kissel, J; Lindblad, B A; Linkert, D; Linkert, G; Mann, I B

1992-09-11

Submicrometer- to micrometer-sized particles were recorded by the Ulysses dust detector within 40 days of the Jupiter flyby. Nine impacts were recorded within 50 Jupiter radii with most of them recorded after closest approach. Three of these impacts are consistent with particles on prograde orbits around Jupiter and the rest are believed to have resulted from gravitationally focused interplanetary dust. From the ratio of the impact rate before the Jupiter flyby to the impact rate after the Jupiter flyby it is concluded that interplanetary dust particles at the distance of Jupiter move on mostly retrograde orbits. On 10 March 1992, Ulysses passed through an intense dust stream. The dust detector recorded 126 impacts within 26 hours. The stream particles were moving on highly inclined and apparently hyperbolic orbits with perihelion distances of >5 astronomical units. Interplanetary dust is lost rather quickly from the solar system through collisions and other mechanisms and must be almost continuously replenished to maintain observed abundances. Dust flux measurements, therefore, give evidence of the recent rates of production from sources such as comets, asteroids, and moons, as well as the possible presence of interstellar grains.

Source apportionment and health risk assessment of potentially toxic elements in road dust from urban industrial areas of Ahvaz megacity, Iran.

Science.gov (United States)

Najmeddin, Ali; Keshavarzi, Behnam; Moore, Farid; Lahijanzadeh, Ahmadreza

2017-10-28

This study investigates the occurrence and spatial distribution of potentially toxic elements (PTEs) (Hg, Cd, Cu, Mo, Pb, Zn, Ni, Co, Cr, Al, Fe, Mn, V and Sb) in 67 road dust samples collected from urban industrial areas in Ahvaz megacity, southwest of Iran. Geochemical methods, multivariate statistics, geostatistics and health risk assessment model were adopted to study the spatial pollution pattern and to identify the priority pollutants, regions of concern and sources of the studied PTEs. Also, receptor positive matrix factorization model was employed to assess pollution sources. Compared to the local background, the median enrichment factor values revealed the following order: Sb > Pb > Hg > Zn > Cu > V > Fe > Mo > Cd > Mn > Cr ≈ Co ≈ Al ≈ Ni. Statistical results show that a significant difference exists between concentrations of Mo, Cu, Pb, Zn, Fe, Sb, V and Hg in different regions (univariate analysis, Kruskal-Wallis test p matrix factorization model revealed that traffic-related emissions (43.5%) and steel industries (26.4%) were first two sources of PTEs in road dust, followed by natural sources (22.6%) and pipe and oil processing companies (7.5%). The arithmetic mean of pollution load index (PLI) values for high traffic sector (1.92) is greater than industrial (1.80) and residential areas (1.25). Also, the results show that ecological risk values for Hg and Pb in 41.8 and 9% of total dust samples are higher than 80, indicating their considerable or higher potential ecological risk. The health risk assessment model showed that ingestion of dust particles contributed more than 83% of the overall non-carcinogenic risk. For both residential and industrial scenarios, Hg and Pb had the highest risk values, whereas Mo has the lowest value.

Impact of Asian Dust on Climate and Air Quality

Science.gov (United States)

Chin, Mian; Tan, Qian; Diehl, Thomas; Yu, Hongbin

2010-01-01

Dust generated from Asian permanent desert and desertification areas can be efficiently transported around the globe, making significant radiative impact through their absorbing and scattering solar radiation and through their deposition on snow and ice to modify the surface albedo. Asian dust is also a major concern of surface air quality not only in the source and immediate downwind regions but also areas thousands of miles away across the Pacific. We present here a global model, GOCART, analysis of data from satellite remote sensing instrument (MODIS, MISR, CALIPSO, OMI) and other observations on Asian dust sources, transport, and deposition, and use the model to assess the Asian dust impact on global climate and air quality.

Gathering dust: A galaxy-wide study of dust emission from cloud complexes in NGC 300

Science.gov (United States)

Riener, M.; Faesi, C. M.; Forbrich, J.; Lada, C. J.

2018-05-01

Aims: We use multi-band observations by the Herschel Space Observatory to study the dust emission properties of the nearby spiral galaxy NGC 300. We compile a first catalogue of the population of giant dust clouds (GDCs) in NGC 300, including temperature and mass estimates, and give an estimate of the total dust mass of the galaxy. Methods: We carried out source detection with the multiwavelength source extraction algorithm getsources. We calculated physical properties, including mass and temperature, of the GDCs from five-band Herschel PACS and SPIRE observations from 100 to 500 μm; the final size and mass estimates are based on the observations at 250 μm that have an effective spatial resolution of 170 pc. We correlated our final catalogue of GDCs to pre-existing catalogues of HII regions to infer the number of GDCs associated with high-mass star formation and determined the Hα emission of the GDCs. Results: Our final catalogue of GDCs includes 146 sources, 90 of which are associated with known HII regions. We find that the dust masses of the GDCs are completely dominated by the cold dust component and range from 1.1 × 103 to 1.4 × 104 M⊙. The GDCs have effective temperatures of 13-23 K and show a distinct cold dust effective temperature gradient from the centre towards the outer parts of the stellar disk. We find that the population of GDCs in our catalogue constitutes 16% of the total dust mass of NGC 300, which we estimate to be about 5.4 × 106 M⊙. At least about 87% of our GDCs have a high enough average dust mass surface density to provide sufficient shielding to harbour molecular clouds. We compare our results to previous pointed molecular gas observations in NGC 300 and results from other nearby galaxies and also conclude that it is very likely that most of our GDCs are associated with complexes of giant molecular clouds. The catalogue is only available at the CDS via anonymous ftp to cdsarc.u-strasbg.fr (130.79.128.5) or via http

Consideration of Fugitive Emissions in Major Source Determinations

Science.gov (United States)

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

The Spatial Variation of Dust Particulate Matter Concentrations during Two Icelandic Dust Storms in 2015

Directory of Open Access Journals (Sweden)

Pavla Dagsson-Waldhauserova

2016-06-01

Full Text Available Particulate matter mass concentrations and size fractions of PM1, PM2.5, PM4, PM10, and PM15 measured in transversal horizontal profile of two dust storms in southwestern Iceland are presented. Images from a camera network were used to estimate the visibility and spatial extent of measured dust events. Numerical simulations were used to calculate the total dust flux from the sources as 180,000 and 280,000 tons for each storm. The mean PM15 concentrations inside of the dust plumes varied from 10 to 1600 µg·m−3 (PM10 = 7 to 583 µg·m−3. The mean PM1 concentrations were 97–241 µg·m−3 with a maximum of 261 µg·m−3 for the first storm. The PM1/PM2.5 ratios of >0.9 and PM1/PM10 ratios of 0.34–0.63 show that suspension of volcanic materials in Iceland causes air pollution with extremely high PM1 concentrations, similar to polluted urban areas in Europe or Asia. Icelandic volcanic dust consists of a higher proportion of submicron particles compared to crustal dust. Both dust storms occurred in relatively densely inhabited areas of Iceland. First results on size partitioning of Icelandic dust presented here should challenge health authorities to enhance research in relation to dust and shows the need for public dust warning systems.

ORIGIN OF DUST AROUND V1309 SCO

International Nuclear Information System (INIS)

Zhu, Chunhua; Lü, Guoliang; Wang, Zhaojun

2013-01-01

The origin of dust grains in the interstellar medium is still an unanswered problem. Nicholls et al. found the presence of a significant amount of dust around V1309 Sco, which may originate from the merger of a contact binary. We investigate the origin of dust around V1309 Sco and suggest that these dust grains are produced in the binary-merger ejecta. By means of the AGBDUST code, we estimate that ∼5.2 × 10 –4 M ☉ dust grains are produced with a radii of ∼10 –5 cm. These dust grains are mainly composed of silicate and iron grains. Because the mass of the binary merger ejecta is very small, the contribution of dust produced by binary merger ejecta to the overall dust production in the interstellar medium is negligible. However, it is important to note that the discovery of a significant amount of dust around V1309 Sco offers a direct support for the idea that common-envelope ejecta provides an ideal environment for dust formation and growth. Therefore, we confirm that common envelope ejecta can be important source of cosmic dust

Assessment of state-of-the-art dust emission scheme in GEOS

Science.gov (United States)

Darmenov, A.; Liu, X.; Prigent, C.

2017-12-01

The GEOS modeling system has been extended with state-of-the-art parameterization of dust emissions based on the vertical flux formulation described in Kok et al., 2014. The new dust scheme was coupled with the GOCART and MAM aerosol models. In the present study we compared dust emissions, aerosol optical depth (AOD) and radiative fluxes from GEOS experiments with the standard and new dust emissions. AOD from the model experiments were also compared with AERONET and satellite based AOD product. Based on this comparative analysis we concluded that the new parameterization improved the GEOS capability to model dust aerosols originating from African sources, however it led to overestimation of dust emissions from Asian and Middle-Eastern sources. Further regional tuning of key parameters controlling the threshold friction velocity may be required in order to attain more definitive and uniform improvement in the dust modeling skill with the newly implemented dust emissions scheme.

Research and development in dust and silicosis suppression

Energy Technology Data Exchange (ETDEWEB)

Breuer, H

1975-08-21

MAK values of 4 mg/m/sup 3/ for respirable dust containing quartz and 0.15 mg/m/sup 3/ for respirable quartz dust have been established for 5 years' exposure in West German hard coal mines. Routine gravimetric measurements were introduced in 1974 and these are supplemented by the digital Tyndallometer which indicates short-term variations. Gravimetric measurements have indicated the main sources of dust and improved dust suppression measures have considerably reduced respirable dust concentrations in some cases, e.g., by seam infusion, by spraying of the face machine path and at crushers, and by dedusters on heading machines.

Emerging ecological datasets with application for modeling North American dust emissions

Science.gov (United States)

McCord, S.; Stauffer, N. G.; Garman, S.; Webb, N.

2017-12-01

In 2011 the US Bureau of Land Management (BLM) established the Assessment, Inventory and Monitoring (AIM) program to monitor the condition of BLM land and to provide data to support evidence-based management of multi-use public lands. The monitoring program shares core data collection methods with the Natural Resources Conservation Service's (NRCS) National Resources Inventory (NRI), implemented on private lands nationally. Combined, the two programs have sampled >30,000 locations since 2003 to provide vegetation composition, vegetation canopy height, the size distribution of inter-canopy gaps, soil texture and crusting information on rangelands and pasture lands across North America. The BLM implements AIM on more than 247.3 million acres of land across the western US, encompassing major dust source regions of the Chihuahuan, Sonoran, Mojave and Great Basin deserts, the Colorado Plateau, and potential high-latitude dust sources in Alaska. The AIM data are publicly available and can be used to support modeling of land surface and boundary-layer processes, including dust emission. While understanding US dust source regions and emission processes has been of national interest since the 1930s Dust Bowl, most attention has been directed to the croplands of the Great Plains and emission hot spots like Owens Lake, California. The magnitude, spatial extent and temporal dynamics of dust emissions from western dust source areas remain highly uncertain. Here, we use ensemble modeling with empirical and physically-based dust emission schemes applied to AIM monitoring data to assess regional-scale patterns of aeolian sediment mass fluxes and dust emissions. The analysis enables connections to be made between dust emission rates at source and other indicators of ecosystem function at the landscape scale. Emerging ecological datasets like AIM provide new opportunities to evaluate aeolian sediment transport responses to land surface conditions, potential interactions with

Regional Modeling of Dust Mass Balance and Radiative Forcing over East Asia using WRF-Chem

Energy Technology Data Exchange (ETDEWEB)

Chen, Siyu; Zhao, Chun; Qian, Yun; Leung, Lai-Yung R.; Huang, J.; Huang, Zhongwei; Bi, Jianrong; Zhang, Wu; Shi, Jinsen; Yang, Lei; Li, Deshuai; Li, Jinxin

2014-12-01

The Weather Research and Forecasting model with Chemistry (WRF-Chem) is used to investigate the seasonal and annual variations of mineral dust over East Asia during 2007-2011, with a focus on the dust mass balance and radiative forcing. A variety of measurements from in-stu and satellite observations have been used to evaluate simulation results. Generally, WRF-Chem reproduces not only the column variability but also the vertical profile and size distribution of mineral dust over and near the dust source regions of East Asia. We investigate the dust lifecycle and the factors that control the seasonal and spatial variations of dust mass balance and radiative forcing over the seven sub-regions of East Asia, i.e. source regions, the Tibetan Plateau, Northern China, Southern China, the ocean outflow region, and Korea-Japan regions. Results show that, over the source regions, transport and dry deposition are the two dominant sinks. Transport contributes to ~30% of the dust sink over the source regions. Dust results in a surface cooling of up to -14 and -10 W m-2, atmospheric warming of up to 20 and 15 W m-2, and TOA cooling of -5 and -8 W m-2 over the two major dust source regions of East Asia, respectively. Over the Tibetan Plateau, transport is the dominant source with a peak in summer. Over identified outflow regions, maximum dust mass loading in spring is contributed by the transport. Dry and wet depositions are the comparably dominant sinks, but wet deposition is larger than dry deposition over the Korea-Japan region, particularly in spring (70% versus 30%). The WRF-Chem simulations can generally capture the measured features of dust aerosols and its radaitve properties and dust mass balance over East Asia, which provides confidence for use in further investigation of dust impact on climate over East Asia.

Magnetic studies of dusts in the urban environment

International Nuclear Information System (INIS)

Xie, S.

2000-12-01

Dusts are one of the major public health concerns in the urban environment. This study investigates the application of magnetic techniques in the studies of urban dust pollution. Measurements of magnetic properties, element concentrations, and the organic matter content were carried out on Liverpool (UK) street dust and/or Bootle (UK) deposited dust. Mixed dominant ferrimagnetic phases are found in Liverpool street dust although magnetite is probably a major one. The partial susceptibility technique is able to model the contributions of main magnetic components satisfactorily in Liverpool street dust. There are similar spatial distributions for some measurements, such as χLF and Pb, whilst there are different patterns for some measurements, such as χLF and the organic matter content. There are good linear correlations between the organic matter content and some magnetic mineral concentration-related parameters for < 1mm (bulk) samples. Among them, frequency dependent susceptibility (χFD) shows the highest correlation coefficient value. χFD percentage demonstrates a significant correlation with the organic matter content for size fraction and bulk samples. This suggests that re-entrainment of soil is probably a major source of the organic material present in street dust. The ratio χARM /SIRM shows a highly significant correlation with the organic matter content for <150μm fraction samples. The study demonstrates that the simple, rapid, and non-destructive magnetic measurements may be used as proxies for the organic matter content in street dust. Associations between magnetic properties and element concentrations are investigated by using correlation analysis and factor analysis, which may be a potential approach for source identification of magnetic material in the environment. The study suggests that ferrimagnetic minerals are the dominant magnetic component in Bootle dust samples. Both studied sites show similar magnetic properties, but they can be

75 FR 38745 - Approval and Promulgation of Implementation Plans; State of Iowa

Science.gov (United States)

2010-07-06

... that no person shall cause, allow, or permit fugitive dust material to become airborne in such..., Incorporation by reference, Intergovernmental relations, Lead, Nitrogen dioxide, Ozone, Particulate matter...

Onset of frequent dust storms in northern China at ~AD 1100.

Science.gov (United States)

He, Yuxin; Zhao, Cheng; Song, Mu; Liu, Weiguo; Chen, Fahu; Zhang, Dian; Liu, Zhonghui

2015-11-26

Dust storms in northern China strongly affect the living and health of people there and the dusts could travel a full circle of the globe in a short time. Historically, more frequent dust storms occurred during cool periods, particularly the Little Ice Age (LIA), generally attributed to the strengthened Siberian High. However, limited by chronological uncertainties in proxy records, this mechanism may not fully reveal the causes of dust storm frequency changes. Here we present a late Holocene dust record from the Qaidam Basin, where hydrological changes were previously reconstructed, and examine dust records from northern China, including the ones from historical documents. The records, being broadly consistent, indicate the onset of frequent dust storms at ~AD 1100. Further, peaked dust storm events occurred at episodes of high total solar irradiance or warm-dry conditions in source regions, superimposed on the high background of frequent dust storms within the cool LIA period. We thus suggest that besides strong wind activities, the centennial-scale dust storm events over the last 1000 years appear to be linked to the increased availability of dust source. With the anticipated global warming and deteriorating vegetation coverage, frequent occurrence of dust storms in northern China would be expected to persist.

INTELLIGENCE STUDIES IN FORENSIC CRIMINOLOGY OF FUGITIVE EMANATING DEFINITIVE AND LOCATIONAL PARAMETERS - Dissertation without Errata

OpenAIRE

Nyagudi, Nyagudi Musandu

2014-01-01

This dissertation addresses the problem of manhunts, against criminal fugitives. It establishesnew ways of describing and refining mechanisms and techniques, for manhunts. Methods used in thisdissertation to meet those objectives, include: review of case studies, benchmarking of techniques andthe analysis of techniques and concepts, which have been put forward by other scholars. Emphasishas been placed on the applicability of search techniques to a wide range of situations, and techniques for...

Normal and anomalous diffusion in fluctuations of dust concentration nearby emission source

Science.gov (United States)

Szczurek, Andrzej; Maciejewska, Monika; Wyłomańska, Agnieszka; Sikora, Grzegorz; Balcerek, Michał; Teuerle, Marek

2018-02-01

Particulate matter (PM) is an important component of air. Nowadays, major attention is payed to fine dust. It has considerable environmental impact, including adverse effect on human health. One of important issues regarding PM is the temporal variation of its concentration. The variation contains information about factors influencing this quantity in time. The work focuses on the character of PM concentration dynamics indoors, in the vicinity of emission source. The objective was to recognize between the homogeneous or heterogeneous dynamics. The goal was achieved by detecting normal and anomalous diffusion in fluctuations of PM concentration. For this purpose we used anomalous diffusion exponent, β which was derived from Mean Square Displacement (MSD) analysis. The information about PM concentration dynamics may be used to design sampling strategy, which serves to attain representative information about PM behavior in time. The data analyzed in this work was collected from single-point PM concentration monitoring in the vicinity of seven emission sources in industrial environment. In majority of cases we observed heterogeneous character of PM concentration dynamics. It confirms the complexity of interactions between the emission sources and indoor environment. This result also votes against simplistic approach to PM concentration measurement indoors, namely their occasional character, short measurement periods and long term averaging.

Numerical Prediction of Dust. Chapter 10

Science.gov (United States)

Benedetti, Angela; Baldasano, J. M.; Basart, S.; Benincasa, F.; Boucher, O.; Brooks, M.; Chen, J. P.; Colarco, P. R.; Gong, S.; Huneeus, N.;

Effects of two Asian sand dusts transported from the dust source regions of Inner Mongolia and northeast China on murine lung eosinophilia

Energy Technology Data Exchange (ETDEWEB)

He, Miao, E-mail: hemiao.cmu@gmail.com [Environment and Chronic Non-communicable Disease Research Center, College of Public Health, China Medical University, 11001 Shenyang (China); Department of Health Sciences, Oita University of Nursing and Health Sciences, 870-1201 Oita (Japan); Ichinose, Takamichi, E-mail: ichinose@oita-nhs.ac.jp [Department of Health Sciences, Oita University of Nursing and Health Sciences, 870-1201 Oita (Japan); Song, Yuan, E-mail: freude@med.uoeh-u.ac.jp [Department of Immunology and Parasitology, School of Medicine, University of Occupational and Environmental Health, Iseigaoka, Yahata-nishi-ku, Kitakyushu, 807-8555 Fukuoka (Japan); Yoshida, Yasuhiro, E-mail: songyuan1107@163.com [Department of Immunology and Parasitology, School of Medicine, University of Occupational and Environmental Health, Iseigaoka, Yahata-nishi-ku, Kitakyushu, 807-8555 Fukuoka (Japan); Arashidani, Keiichi, E-mail: arashi@snow.ocn.ne.jp [Department of Immunology and Parasitology, School of Medicine, University of Occupational and Environmental Health, Iseigaoka, Yahata-nishi-ku, Kitakyushu, 807-8555 Fukuoka (Japan); Yoshida, Seiichi, E-mail: syoshida@oita-nhs.ac.jp [Department of Health Sciences, Oita University of Nursing and Health Sciences, 870-1201 Oita (Japan); Liu, Boying, E-mail: boyingliu321@gmail.com [Environment and Chronic Non-communicable Disease Research Center, College of Public Health, China Medical University, 11001 Shenyang (China); Department of Health Sciences, Oita University of Nursing and Health Sciences, 870-1201 Oita (Japan); Nishikawa, Masataka, E-mail: mnishi@nies.go.jp [Environmental Chemistry Division, National Institute for Environmental Studies, 305-8506 Tsukuba, Ibaraki (Japan); Takano, Hirohisa, E-mail: htakano@health.env.kyoto-u.ac.jp [Environmental Health Division, Department of Environmental Engineering, Graduate School of Engineering, Kyoto University, Kyoto daigaku-Katsura, Nishikyo-ku, Kyoto 615-8530 (Japan); and others

2013-11-01

The quality and quantity of toxic materials adsorbed onto Asian sand dust (ASD) are different based on dust source regions and passage routes. The aggravating effects of two ASDs (ASD1 and ASD2) transported from the source regions of Inner Mongolia and northeast China on lung eosinophilia were compared to clarify the role of toxic materials in ASD. The ASDs contained different amounts of lipopolysaccharides (LPS) and β-glucan (ASD1 < ASD2) and SiO{sub 2} (ASD1 > ASD2). CD-1 mice were instilled intratracheally with ASD1, ASD2 and/or ovalbumin (OVA) four times at 2-week intervals. ASD1 and ASD2 enhanced eosinophil recruitment induced by OVA in the submucosa of the airway, with goblet cell proliferation in the bronchial epithelium. ASD1 and ASD2 synergistically increased OVA-induced eosinophil-relevant cytokines interleukin-5 (IL-5), IL-13 (ASD1 < ASD2) and chemokine eotaxin (ASD1 > ASD2) in bronchoalveolar lavage fluid. ASD2 aggravating effects on lung eosinophilia were greater than ASD1. The role of LPS and β-glucan in ASD2 on the production of pro-inflammatory mediators was assessed using in vitro bone marrow-derived macrophages (BMDMs) from wild type, Toll-like receptor 2-deficient (TLR2 −/−), TLR4 −/−, and MyD88 −/− mice (on Balb/c background). ASD2-stimulated TLR2 −/− BMDMs enhanced IL-6, IL-12, TNF-α, MCP-1 and MIP-1α secretion compared with ASD2-stimulated TLR4 −/− BMDMs. Protein expression from ASD2-stimulated MyD88 −/− BMDM were very low or undetectable. The in vitro results indicate that lung eosinophilia caused by ASD is TLR4 dependent. Therefore, the aggravation of OVA-related lung eosinophilia by ASD may be dependent on toxic substances derived from microbes, such as LPS, rather than SiO{sub 2}. - Highlights: • Asian sand dust (ASD) from the deserts of China causes serious respiratory problems. • The aggravating effects of two ASDs on lung eosinophilia were compared. • The ASDs contained different LPS and β-glucan (ASD1

Effects of two Asian sand dusts transported from the dust source regions of Inner Mongolia and northeast China on murine lung eosinophilia

International Nuclear Information System (INIS)

He, Miao; Ichinose, Takamichi; Song, Yuan; Yoshida, Yasuhiro; Arashidani, Keiichi; Yoshida, Seiichi; Liu, Boying; Nishikawa, Masataka; Takano, Hirohisa

2013-01-01

The quality and quantity of toxic materials adsorbed onto Asian sand dust (ASD) are different based on dust source regions and passage routes. The aggravating effects of two ASDs (ASD1 and ASD2) transported from the source regions of Inner Mongolia and northeast China on lung eosinophilia were compared to clarify the role of toxic materials in ASD. The ASDs contained different amounts of lipopolysaccharides (LPS) and β-glucan (ASD1 2 (ASD1 > ASD2). CD-1 mice were instilled intratracheally with ASD1, ASD2 and/or ovalbumin (OVA) four times at 2-week intervals. ASD1 and ASD2 enhanced eosinophil recruitment induced by OVA in the submucosa of the airway, with goblet cell proliferation in the bronchial epithelium. ASD1 and ASD2 synergistically increased OVA-induced eosinophil-relevant cytokines interleukin-5 (IL-5), IL-13 (ASD1 ASD2) in bronchoalveolar lavage fluid. ASD2 aggravating effects on lung eosinophilia were greater than ASD1. The role of LPS and β-glucan in ASD2 on the production of pro-inflammatory mediators was assessed using in vitro bone marrow-derived macrophages (BMDMs) from wild type, Toll-like receptor 2-deficient (TLR2 −/−), TLR4 −/−, and MyD88 −/− mice (on Balb/c background). ASD2-stimulated TLR2 −/− BMDMs enhanced IL-6, IL-12, TNF-α, MCP-1 and MIP-1α secretion compared with ASD2-stimulated TLR4 −/− BMDMs. Protein expression from ASD2-stimulated MyD88 −/− BMDM were very low or undetectable. The in vitro results indicate that lung eosinophilia caused by ASD is TLR4 dependent. Therefore, the aggravation of OVA-related lung eosinophilia by ASD may be dependent on toxic substances derived from microbes, such as LPS, rather than SiO 2 . - Highlights: • Asian sand dust (ASD) from the deserts of China causes serious respiratory problems. • The aggravating effects of two ASDs on lung eosinophilia were compared. • The ASDs contained different LPS and β-glucan (ASD1 2 (ASD1 > ASD2). • The ASD2 aggravating effects on lung

Reconciling PM10 analyses by different sampling methods for Iron King Mine tailings dust.

Science.gov (United States)

Li, Xu; Félix, Omar I; Gonzales, Patricia; Sáez, Avelino Eduardo; Ela, Wendell P

2016-03-01

The overall project objective at the Iron King Mine Superfund site is to determine the level and potential risk associated with heavy metal exposure of the proximate population emanating from the site's tailings pile. To provide sufficient size-fractioned dust for multi-discipline research studies, a dust generator was built and is now being used to generate size-fractioned dust samples for toxicity investigations using in vitro cell culture and animal exposure experiments as well as studies on geochemical characterization and bioassay solubilization with simulated lung and gastric fluid extractants. The objective of this study is to provide a robust method for source identification by comparing the tailing sample produced by dust generator and that collected by MOUDI sampler. As and Pb concentrations of the PM10 fraction in the MOUDI sample were much lower than in tailing samples produced by the dust generator, indicating a dilution of Iron King tailing dust by dust from other sources. For source apportionment purposes, single element concentration method was used based on the assumption that the PM10 fraction comes from a background source plus the Iron King tailing source. The method's conclusion that nearly all arsenic and lead in the PM10 dust fraction originated from the tailings substantiates our previous Pb and Sr isotope study conclusion. As and Pb showed a similar mass fraction from Iron King for all sites suggesting that As and Pb have the same major emission source. Further validation of this simple source apportionment method is needed based on other elements and sites.

Origin of Harmattan dust settled in Northern Ghana – Long transported or local dust?

DEFF Research Database (Denmark)

Lyngsie, Gry; Awadzi, Theodore W; Breuning-Madsen, Henrik

2011-01-01

is that the majority of dust deposited in northern Ghana may not be from the original Harmattan source in the Bodélé Depression. The aim of this study is therefore to investigate the origin of deposited dust in Tamale, Ghana. This is examined by comparing wind data, grain size distribution, mineralogical......The Harmattan is a dry, dust-laden continental wind which has its origin in the Bodélé Depression in the Chad basin. In Ghana the Harmattan can be experienced from November to March, when the Harmattan replaces the dominant south westerly maritime Monsoon wind. The hypothesis of this study...... and geochemical data from dust samples deposited during the Harmattan and Monsoon seasons, and topsoil. This study shows that despite a clear difference between the wind directions in the Harmattan and Monsoon seasons in Tamale, northern Ghana, no distinct differences are observed between the mineral or elemental...

Dust emission: small-scale processes with global consequences

Science.gov (United States)

Okin, Gregory S.; Bullard, Joanna E.; Reynolds, Richard L.; Ballantine, John-Andrew C.; Schepanski, Kerstin; Todd, Martin C.; Belnap, Jayne; Baddock, Matthew C.; Gill, Thomas E.; Miller, Mark E.

2011-01-01

Desert dust, both modern and ancient, is a critical component of the Earth system. Atmospheric dust has important effects on climate by changing the atmospheric radiation budget, while deposited dust influences biogeochemical cycles in the oceans and on land. Dust deposited on snow and ice decreases its albedo, allowing more light to be trapped at the surface, thus increasing the rate of melt and influencing energy budgets and river discharge. In the human realm, dust contributes to the transport of allergens and pathogens and when inhaled can cause or aggravate respiratory diseases. Dust storms also represent a significant hazard to road and air travel. Because it affects so many Earth processes, dust is studied from a variety of perspectives and at multiple scales, with various disciplines examining emissions for different purposes using disparate strategies. Thus, the range of objectives in studying dust, as well as experimental approaches and results, has not yet been systematically integrated. Key research questions surrounding the production and sources of dust could benefit from improved collaboration among different research communities. These questions involve the origins of dust, factors that influence dust production and emission, and methods through which dust can be monitored.

Systematic characterization of structural, dynamical and electrical properties of dust devils and implications for dust lifting processes

Science.gov (United States)

Franzese, Gabriele; Esposito, Francesca; Lorenz, Ralph D.; Popa, Ciprian; Silvestro, Simone; Deniskina, Natalia; Cozzolino, Fabio

2017-04-01

scale. Instead, on Mars the presence of the dust devils has been confirmed at almost every latitude and altitude and it has been indicated as the possible main source of suspended dust outside the storm seasons. Hence, the study of the dust devils becomes of great importance in order to understand the atmospheric dust loading and the global climate of the planet. In addition, the dust lifting phenomena are probably one of the main source of atmospheric electrification on Mars and the measurement and study of the Martian boundary layer electric field is one of the main objectives of the future Martian space missions, such as ExoMars 2020. Indeed, this mission will accommodate "Dust Complex", a suite of sensors that will monitor lifted dust and atmospheric electric field on the surface of Mars. For these reasons, the present work represents a useful tool for the understanding of the dust lifting phenomena and their electrification both on Earth and on Mars.

Investigation of snow cover dust pollution by contact and satellite observations

Science.gov (United States)

Raputa, Vladimir F.; Yaroslavtseva, Tatyana V.

2015-11-01

The problems of reconstructing the snow cover pollution fields from dusting, point, linear and area sources according to ground and satellite observations are considered. Using reconstruction models, the methods of the combined analysis of the characteristic images of snow cover pollution haloes in the vicinity of sources of dust and contact data observations have been developed. On the basis of the numerical data analysis of ground monitoring and satellite imagery, the stable quantitative regularities between the fields of dust fallouts and the intensity of a change of tones of gray in the radial directions relative to the main sources are identified.

Benzene observations and source appointment in a region of oil and natural gas development

Science.gov (United States)

Halliday, Hannah Selene

Benzene is a primarily anthropogenic volatile organic compound (VOC) with a small number of well characterized sources. Atmospheric benzene affects human health and welfare, and low level exposure (Atmospheric Observatory (PAO) in Colorado to investigate how O&NG development impacts air quality within the Wattenburg Gas Field (WGF) in the Denver-Julesburg Basin. The measurements were carried out in July and August 2014 as part of NASA's DISCOVER-AQ field campaign. The PTR-QMS data were supported by pressurized whole air canister samples and airborne vertical and horizontal surveys of VOCs. Unexpectedly high benzene mixing ratios were observed at PAO at ground level (mean benzene = 0.53 ppbv, maximum benzene = 29.3 ppbv), primarily at night (mean nighttime benzene = 0.73 ppbv). These high benzene levels were associated with southwesterly winds. The airborne measurements indicate that benzene originated from within the WGF, and typical source signatures detected in the canister samples implicate emissions from O&NG activities rather than urban vehicular emissions as primary benzene source. This conclusion is backed by a regional toluene-to-benzene ratio analysis which associated southerly flow with vehicular emissions from the Denver area. Weak benzene-to-CO correlations confirmed that traffic emissions were not responsible for the observed high benzene levels. Previous measurements at the Boulder Atmospheric Observatory (BAO) and our data obtained at PAO allow us to locate the source of benzene enhancements between the two atmospheric observatories. Fugitive emissions of benzene from O&NG operations in the Platteville area are discussed as the most likely causes of enhanced benzene levels at PAO. A limited information source attribution with the PAO dataset was completed using the EPA's positive matrix factorization (PMF) source receptor model. Six VOCs from the PTR-QMS measurement were used along with CO and NO for a total of eight chemical species. Six sources

Mass transfer of PBDEs from plastic TV casing to indoor dust via three migration pathways — A test chamber investigation

International Nuclear Information System (INIS)

Rauert, C.; Harrad, S.

2015-01-01

Polybrominated diphenyl ethers (PBDEs) are widely detected in humans with substantial exposure thought to occur in indoor environments and particularly via contact with indoor dust. Despite this, knowledge of how PBDEs migrate to indoor dust from products within which they are incorporated is scarce. This study utilises an in-house designed and built test chamber to investigate the relative significance of different mechanisms via which PBDEs transfer from source materials to dust, using a plastic TV casing treated with the Deca-BDE formulation as a model source. Experiments at both room temperature and 60 °C revealed no detectable transfer of PBDEs from the TV casing to dust via volatilisation and subsequent partitioning. In contrast, substantial transfer of PBDEs to dust was detected when the TV casing was abraded using a magnetic stirrer bar. Rapid and substantial PBDE transfer to dust was also observed in experiments in which dust was placed in direct contact with the source. Based on these experiments, we suggest that for higher molecular weight PBDEs like BDE-209; direct dust:source contact is the principal pathway via which source-to-dust transfer occurs. - Highlights: • Transfer from a TV casing to dust of high molecular weight PBDEs examined. • Direct source:dust contact effected rapid and most substantial transfer. • Substantial source:dust transfer also occurred via abrasion of source

Transport of Mineral Dust and Its Impact on Climate

Directory of Open Access Journals (Sweden)

Kerstin Schepanski

2018-04-01

Full Text Available Mineral dust plays a pivotal role in the Earth’s system. Dust modulates the global energy budget directly via its interactions with radiation and indirectly via its influence on cloud and precipitation formation processes. Dust is a micro-nutrient and fertilizer for ecosystems due to its mineralogical composition and thus impacts on the global carbon cycle. Hence, dust aerosol is an essential part of weather and climate. Dust suspended in the air is determined by the atmospheric dust cycle: Dust sources and emission processes define the amount of dust entrained into the atmosphere. Atmospheric mixing and circulation carry plumes of dust to remote places. Ultimately, dust particles are removed from the atmosphere by deposition processes such as gravitational settling and rain wash out. During its residence time, dust interacts with and thus modulates the atmosphere resulting into changes such as in surface temperature, wind, clouds, and precipitation rates. There are still uncertainties regarding individual dust interactions and their relevance. Dust modulates key processes that are inevitably influencing the Earth energy budget. Dust transport allows for these interactions and at the same time, the intermittency of dust transport introduces additional fluctuations into a complex and challenging system.

A survey of spatially distributed exterior dust lead loadings in New York City

Energy Technology Data Exchange (ETDEWEB)

Caravanos, Jack [Hunter College-CUNY, School of Health Sciences (United States); Weiss, Arlene L [Environmental Medicine Inc., 263 Center Avenue, Westwood, NJ 07675 (United States); School of Medicine, New York University, NY 10016 (United States); Blaise, Marc J [Hunter College-CUNY, School of Health Sciences (United States); Jaeger, Rudolph J [Environmental Medicine Inc., 263 Center Avenue, Westwood, NJ 07675 (United States) and School of Medicine, New York University, NY 10016 (United States)

2006-02-15

This work documents ambient lead dust deposition values (lead loading) for the boroughs of New York City in 2003-2004. Currently, no regulatory standards exist for exterior concentrations of lead in settled dust. This is in contrast to the clearance and risk assessment standards that exist for interior residential dust. The reported potential for neurobehavioral toxicity and adverse cognitive development in children due to lead exposure prompts public health concerns about undocumented lead sources. Such sources may include settled dust of outdoor origin. Dust sampling throughout the five boroughs of NYC was done from the top horizontal portion of pedestrian traffic control signals (PTCS) at selected street intersections along main thoroughfares. The data (n=214 samples) show that lead in dust varies within each borough with Brooklyn having the highest median concentration (730{mu}g/ft{sup 2}), followed in descending order by Staten Island (452{mu}g/ft{sup 2}), the Bronx (382{mu}g/ft{sup 2}), Queens (198{mu}g/ft{sup 2}) and finally, Manhattan (175{mu}g/ft{sup 2}). When compared to the HUD/EPA indoor lead in dust standard of 40{mu}g/ft{sup 2}, our data show that this value is exceeded in 86% of the samples taken. An effort was made to determine the source of the lead in the dust atop of the PTCS. The lead in the dust and the yellow signage paint (which contains lead) were compared using isotopic ratio analysis. Results showed that the lead-based paint chip samples from intact signage did not isotopically match the dust wipe samples taken from the same surface. We know that exterior dust containing lead contributes to interior dust lead loading. Therefore, settled leaded dust in the outdoor environment poses a risk for lead exposure to children living in urban areas, namely, areas with elevated childhood blood lead levels and background lead dust levels from a variety of unidentified sources.

A survey of spatially distributed exterior dust lead loadings in New York City

International Nuclear Information System (INIS)

Caravanos, Jack; Weiss, Arlene L.; Blaise, Marc J.; Jaeger, Rudolph J.

2006-01-01

This work documents ambient lead dust deposition values (lead loading) for the boroughs of New York City in 2003-2004. Currently, no regulatory standards exist for exterior concentrations of lead in settled dust. This is in contrast to the clearance and risk assessment standards that exist for interior residential dust. The reported potential for neurobehavioral toxicity and adverse cognitive development in children due to lead exposure prompts public health concerns about undocumented lead sources. Such sources may include settled dust of outdoor origin. Dust sampling throughout the five boroughs of NYC was done from the top horizontal portion of pedestrian traffic control signals (PTCS) at selected street intersections along main thoroughfares. The data (n=214 samples) show that lead in dust varies within each borough with Brooklyn having the highest median concentration (730μg/ft 2 ), followed in descending order by Staten Island (452μg/ft 2 ), the Bronx (382μg/ft 2 ), Queens (198μg/ft 2 ) and finally, Manhattan (175μg/ft 2 ). When compared to the HUD/EPA indoor lead in dust standard of 40μg/ft 2 , our data show that this value is exceeded in 86% of the samples taken. An effort was made to determine the source of the lead in the dust atop of the PTCS. The lead in the dust and the yellow signage paint (which contains lead) were compared using isotopic ratio analysis. Results showed that the lead-based paint chip samples from intact signage did not isotopically match the dust wipe samples taken from the same surface. We know that exterior dust containing lead contributes to interior dust lead loading. Therefore, settled leaded dust in the outdoor environment poses a risk for lead exposure to children living in urban areas, namely, areas with elevated childhood blood lead levels and background lead dust levels from a variety of unidentified sources

Tracing source, distribution and health risk of potentially harmful elements (PHEs) in street dust of Durgapur, India.

Science.gov (United States)

Gope, Manash; Masto, Reginald Ebhin; George, Joshy; Balachandran, Srinivasan

2018-06-15

Street dust samples from Durgapur, the steel city of eastern India, were collected from five different land use patterns, i.e., national highways, urban residential area, sensitive area, industrial area and busy traffic zone during summer, monsoon, and winter to analyze the pollution characteristics, chemical fractionation, source apportionment and health risk of heavy metals (HMs). The samples were fractionated into ≤ 53 µm and analyzed for potentially harmful elements (PHEs) viz. Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn. Summer season indicated higher concentrations of PHEs when compared to the other two seasons. Mean enrichment factor (EF), geo-accumulation index (Igeo), and contamination factor (CF) were high for Cd followed by Pb during all the three season in Durgapur. Chemical fractionation was executed in order to obtain distribution patterns of PHEs and to evaluate their bioavailable fractions in street dust samples. Mn was found to be highly bioavailable and bioavailability of the PHEs were in the order of Mn > Zn > Pb > Ni > Cd > Cu > Fe > Cr. Principal Component Analysis (PCA), cluster analysis, correlation analysis indicated the main sources of PHEs could be industrial, especially coal powered thermal plant, iron and steel industries and cement industries and vehicular. Multivariate analysis of variance (MANOVA) indicated that sites, seasons and their interaction were significantly affected by different PHEs as a whole. The health risk was calculated with total metal as well as mobile fraction of PHEs, which indicated that the actual non-carcinogenic risk due to bioavailable PHEs was less (HI < 1) when compared to total concentrations of PHEs. Carcinogenic risk was observed for total Cr in street dust (Child: 4.6E-06; Adult: 3.6E-06). Copyright © 2018 Elsevier Inc. All rights reserved.

Origin-Dependent Variations in the Atmospheric Microbiome in Eastern Mediterranean Dust Storms

Science.gov (United States)

Rudich, Y.; Gat, D.

2017-12-01

Microorganisms carried by dust storms are transported through the atmosphere and may affect human health and the functionality of microbial communities in various environments. Characterizing the dust-borne microbiome in dust storms of different origins, or that followed different trajectories, provides valuable data to improve our understanding of global health and environmental impacts. We present a comparative study on the diversity of dust- borne bacterial communities in dust storms from three distinct origins—North Africa, Syria and Saudi Arabia—and compare them with local bacterial communities sampled on clear days, all collected at a single location, in Israel. Storms from different dust origins exhibited distinct bacterial communities, with signature bacterial taxa for each source. Dust storms were characterized by a lower abundance of selected antibiotic resistance genes (ARGs) compared with ambient dust, asserting that the origin of these genes is local, possibly anthropogenic. With the progression of the storm, the storm-borne bacterial community showed increasing resemblance to ambient dust, suggesting mixing with local dust. We will also discuss how exposure to dust containing biological components affect lung epithelial cells. These results show, for the first time, that dust storms from different sources display distinct bacterial communities, suggesting possible distinct effects on the environment and public health.

House-dust mites in our homes are a contamination from outdoor sources.

Science.gov (United States)

Hallas, Thorkil E

2010-05-01

Avoidance advices for house-dust mite sensitized persons are currently based upon the idea, that the mites (Dermatophagoides spp.) are part of the indoor fauna. A closer look at development stages in the house-dust samples shows, however, that only the mites' active stages are present there and that the stages between them, the inactive moulting stages, are absent. Therefore the mites probably do not carry out their life cycles in our dwellings, but are more likely contaminations from the open. Findings of low level concentrations can be explained by mites coming from outdoors and sedimented in accordance with known physical laws. The occasional finding of higher concentrations is the result of synchronized populations of the mites developing outdoors and being passively transported into our homes by wind and dust. The hypothesis explains why we find mites in our homes but nonetheless have no effect of avoidance measures. The verification of the entire hypothesis or part of it may have great impact on the management of the disease house-dust mite allergy.

Organophosphate esters and phthalate esters in human hair from rural and urban areas, Chongqing, China: Concentrations, composition profiles and sources in comparison to street dust.

Science.gov (United States)

He, Ming-Jing; Lu, Jun-Feng; Ma, Jing-Ye; Wang, Huan; Du, Xiao-Fan

2018-06-01

Human hair and street dust from rural and urban areas in Chongqing were collected to analyze Organophosphate esters (OPEs) and phthalate esters (PAEs). Concentrations of OPEs in urban hair were significantly higher than those in rural hair, whereas PAEs concentrations in rural hair were significantly higher than those in urban hair. Different composition patterns of OPEs were observed in rural and urban hair, where tris (2-chloroisopropyl) phosphate (TCIPP), tris (butyl) phosphate (TNBP) and triphenyl phosphate (TPHP) were the dominating analogues in rural hair, accounting for 62.1% of the OPEs burden, and tris (methylphenyl) phosphate (TMPP) exhibited a high contribution in urban hair, responsible for 51.3% of total OPEs, which differed from the composition profiles in corresponding street dust. Analogous composition patterns of PAEs were found in hair of both areas. Di-(2-ethylhexyl) phthalate (DEHP), dibutyl phthalate (DNBP), diisobutyl phthalate (DIBP) and diethyl phthalate (DEP) were the most abundant analogues in hair samples, while DEHP was the predominant analogue in dust samples. No clear tendency was obtained between the increasing ages and the concentrations of both compounds. Most OPEs and PAEs congeners showed significantly positive correlation with one another in rural hair. On the contrary, different correlation patterns were observed in urban hair for OPEs and PAEs, indicating multiple or additional sources existed in urban areas. Significant correlations of OPEs and PAEs were found between hair and corresponding street dust samples, but poor correlations of OPEs and PAEs were observed between rural hair and rural indoor dust, suggesting that street dust may be a predominant exogenous source for human exposure to OPEs and PAEs in this area. Copyright © 2018 Elsevier Ltd. All rights reserved.

Richton Dome air quality analysis: Revision 2

International Nuclear Information System (INIS)

1985-11-01

Detailed supporting calculations, methodology and results of the air quality analysis performed for the Richton Dome Environmental Assessment are presented in this report. Maximum emission rates during site characterization and repository construction and operation are analyzed and reported. The major source of emissions is fugitive dust from construction activities. Modeling was performed primarily with the US Environmental Protection Agency Industrial Source Complex (ISC) Model and meteorological data from Jackson, Mississippi. Predicted maximum ground level concentrations off site are presented. Supporting calculations and computer model runs are presented in appendixes. Salt deposition around the site was predicted and results and supporting analyses are presented. 4 refs., 1 fig., 21 tabs

THREE-DIMENSIONAL DUST MAPPING REVEALS THAT ORION FORMS PART OF A LARGE RING OF DUST

International Nuclear Information System (INIS)

Schlafly, E. F.; Rix, H.-W.; Martin, N. F.; Green, G.; Finkbeiner, D. P.; Burgett, W. S.; Chambers, K. C.; Kaiser, N.; Morgan, J. S.; Tonry, J. L.; Wainscoat, R. J.; Waters, C.; Draper, P. W.; Metcalfe, N.; Price, P. A.

2015-01-01

The Orion Molecular Complex is the nearest site of ongoing high-mass star formation, making it one of the most extensively studied molecular complexes in the Galaxy. We have developed a new technique for mapping the three-dimensional distribution of dust in the Galaxy using Pan-STARRS1 photometry. We isolate the dust at the distance to Orion using this technique, revealing a large (100 pc, 14° diameter), previously unrecognized ring of dust, which we term the ''Orion dust ring''. The ring includes Orion A and B, and is not coincident with current Hα features. The circular morphology suggests formation as an ancient bubble in the interstellar medium, though we have not been able to conclusively identify the source of the bubble. This hint at the history of Orion may have important consequences for models of high-mass star formation and triggered star formation

Dust control at Yucca Mountain project

International Nuclear Information System (INIS)

Kissell, F.; Jurani, R.; Dresel, R.; Reaux, C.

1999-01-01

This report describes actions taken to control silica dust at the Yucca Mountain Exploratory Studies Facility, a tunnel located in Southern Nevada that is part of a scientific program to determine site suitability for a potential nuclear waste repository. The rock is a volcanic tuff containing significant percentages of both quartz and cristobalite. Water use for dust control was limited because of scientific test requirements, and this limitation made dust control a difficult task. Results are reported for two drifts, called the Main Loop Drift and the Cross Drift. In the Main Loop Drift, dust surveys and tracer gas tests indicated that air leakage from the TBM head, the primary ventilation duct, and movement of the conveyor belt were all significant sources of dust. Conventional dust control approaches yielded no significant reductions in dust levels. A novel alternative was to install an air cleaning station on a rear deck of the TBM trailing gear. It filtered dust from the contaminated intake air and discharged clean air towards the front of the TBM. The practical effect was to produce dust levels below the exposure limit for all TBM locations except close to the head. In the Cross Drift, better ventilation and an extra set of dust seals on the TBM served to cut down the leakage of dust from the TBM cutter head. However, the conveyor belt was much dustier than the belt in the main loop drift. The problem originated with dirt on the bottom of the belt return side and much spillage from the belt top side. Achieving lower dust levels in hard rock tunneling operations will require new approaches as well as a more meticulous application of existing technology. Planning for dust control will require specific means to deal with dust that leaks from the TBM head, dust that originates with leaky ventilation systems, and dust that comes from conveyor belts. Also, the application of water could be more efficient if automatic controls were used to adjust the water flow

Suspended dust in Norwegian cities

International Nuclear Information System (INIS)

2001-01-01

According to calculations, at least 80 000 people in Oslo and 8 000 in Trondheim were annoyed by too much suspended dust in 2000. The dust concentration is greatest in the spring, presumably because dust is swirling up from melting snow and ice on the streets. Car traffic is the main source of the dust, except for some of the most highly exposed regions where wood-firing from old stoves contributes up to 70 percent of the dust. National targets for air quality include suspended dust, nitrogen dioxide, sulphur dioxide and benzene. Calculations show that nitrogen dioxide emissions exceeding the limit affected 4 000 people in Oslo and 1 000 people in Trondheim. The sulphur dioxide emissions in the major cities did non exceed the national quality limit; they did exceed the limit in some of the smaller industrial centres. In Trondheim, measurements show that the national limit for benzene was exceeded. Most of the emission of nitrogen dioxide comes from the road traffic. Local air pollution at times causes considerable health- and well-being problems in the larger cities and industrial centres, where a great part of the population may be at risk of early death, infection of the respiratory passage, heart- and lung diseases and cancer

New methods and standards for fine dust

International Nuclear Information System (INIS)

Spielvogel, Juergen; Hartstock, Stefan; Grimm, Hans

2009-01-01

There seems to be common agreement that PM10 is a suboptimal quantity for the quantification of potential dangers from fine dust due to a number of reasons, notably because the chemical composition of the particles is not considered, because the size distribution is disregarded, and because of sampling artefacts. In a first step for improving the particle measurements, the European Community has published new directives for ambient air in June 2008 (EU 2008), which as a main part included new regulations for PM2.5 measurements, in addition to the further on valid regulations for PM10. The comparison of PM2.5 and PM10 may allow a source apportionment and a better assessment of the influence of fine dust on human health. The source apportionment may allow more effective fine dust reduction strategies.

FIELD EVALUATION OF A METHOD FOR ESTIMATING GASEOUS FLUXES FROM AREA SOURCES USING OPEN-PATH FOURIER TRANSFORM INFRARED

Science.gov (United States)

The paper describes preliminary results from a field experiment designed to evaluate a new approach to quantifying gaseous fugitive emissions from area air pollution sources. The new approach combines path-integrated concentration data acquired with any path-integrated optical re...

House-dust mites in our homes are a contamination from outdoor sources

DEFF Research Database (Denmark)

Hallas, Thorkil E.

2010-01-01

there and that the stages between them, the inactive moulting stages, are absent. Therefore the mites probably do not carry out their life cycles in our dwellings, but are more likely contaminations from the open. Findings of low level concentrations can be explained by mites coming from outdoors and sedimented......Avoidance advices for house-dust mite sensitized persons are currently based upon the idea, that the mites (Dermatophagoides spp.) are part of the indoor fauna. A closer look at development stages in the house-dust samples shows, however, that only the mites' active stages are present...... no effect of avoidance measures. The verification of the entire hypothesis or part of it may have great impact on the management of the disease house-dust mite allergy....

Fugitive emission inventory from Brazilian oil and gas industry (2000-2005) and discussion of mitigation measures

Energy Technology Data Exchange (ETDEWEB)

Carloni, Flavia A.; D' Avignon, Alexandre; La Rovere, Emilio L. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Centro Clima

2008-07-01

The objective of this work is to evaluate current emissions of GHGs within the Brazilian oil and gas industry, specifically the fugitive emissions arising from exploration and production. Besides, projects for mitigating these emissions and opportunities for the national industry are investigated. Results show that N{sub 2}O contributes little to fugitive emissions from the oil and gas industry, principally from gas sector. NMVOC emissions are significant, principally from the oil sector. In relation to CO{sub 2} and CH{sub 4} emissions, the oil sector emits more CO{sub 2} while the gas sector contributes more to CH{sub 4} emissions. In both sectors flaring is the activity that emits most CO{sub 2}. In relation to CH{sub 4} the principal contribution to emissions are from exploration and production onshore, although offshore activities as a whole play a greater part in the national industry. The results make it clear that the use of gas from flaring activity is a great opportunity for emission mitigation projects. From a business point of view, methane emissions could mean lost opportunities in selling natural gas. The Kyoto Protocol mechanisms, as the Clean Development Mechanism and Joint Implementation actions, provide the opportunity to stimulate investments in projects for reducing flaring and venting of associated gas. (author)

Saharan dust levels in Greece and received inhalation doses

Directory of Open Access Journals (Sweden)

C. Mitsakou

2008-12-01

Full Text Available The desert of Sahara is one of the major sources of mineral dust on Earth, producing around 2×10⁸ tons/yr. Under certain weather conditions, dust particles from Saharan desert get transported over the Mediterranean Sea and most of Europe. The limiting values set by the directive EC/30/1999 of European Union can easily be exceeded by the transport of desert dust particles in the south European Region and especially in urban areas, where there is also significant contribution from anthropogenic sources. In this study, the effects of dust transport on air quality in several Greek urban areas are quantified. PM₁₀ concentration values from stationary monitoring stations are compared to dust concentrations for the 4-year period 2003–2006. The dust concentration values in the Greek areas were estimated by the SKIRON modelling system coupled with embedded algorithms describing the dust cycle. The mean annual dust contribution to daily-averaged PM₁₀ concentration values was found to be around or even greater than 10% in the urban areas throughout the years examined. Natural dust transport may contribute by more than 20% to the annual number of exceedances – PM₁₀ values greater than EU limits – depending on the specific monitoring location. In a second stage of the study, the inhaled lung dose received by the residents in various Greek locations is calculated. The particle deposition efficiency of mineral dust at the different parts of the human respiratory tract is determined by applying a lung dosimetry numerical model, which incorporates inhalation dynamics and aerosol physical processes. The inhalation dose from mineral dust particles was greater in the upper respiratory system (extrathoracic region and less significant in the lungs, especially in the sensitive alveolar region. However, in cases of dust episodes, the amounts of mineral dust deposited along the human lung are comparable to those

Measurements of industrial fugitive emissions by the FTIR Tracer Method (FTM)

International Nuclear Information System (INIS)

Mellqvist, J.; Arlander, B.; Galle, B.; Bergqvist, B.

1996-01-01

A new method called the FTIR Tracer Method (FTM), has been developed for measuring and quantifying fugitive (diffuse) emissions of hydrocarbons. The method has been evaluated in field experiments which were conducted in the vicinity of several petrochemical plants and an oil refinery during 1993-1995. The technique is based on concentration measurements with infrared remote sensing by Long Path Fourier Transform InfraRed (LPFTIR), combined with tracer releases. The field experiments show the FTM to be very useful for mass flux measurements of both alkanes and alkenes and that the measurements are consistent with the conventional SF 6 method. However, the technique needs to be further validated and a more thorough understanding of the measurement uncertainties have to be achieved

RR Tel: Determination of Dust Properties During Minimum Obscuration

Directory of Open Access Journals (Sweden)

Jurkić T.

2012-06-01

Full Text Available the ISO infrared spectra and the SAAO long-term JHKL photometry of RR Tel in the epochs during minimum obscuration are studied in order to construct a circumstellar dust model. the spectral energy distribution in the near- and the mid-IR spectral range (1–15 μm was obtained for an epoch without the pronounced dust obscuration. the DUSTY code was used to solve the radiative transfer through the dust and to determine the circumstellar dust properties of the inner dust regions around the Mira component. Dust temperature, maximum grain size, dust density distribution, mass-loss rate, terminal wind velocity and optical depth are determined. the spectral energy distribution and the long-term JHKL photometry during an epoch of minimum obscuration show almost unattenuated stellar source and strong dust emission which cannot be explained by a single dust shell model. We propose a two-component model consisting of an optically thin circmustellar dust shell and optically thick dust outside the line of sight in some kind of a flattened geometry, which is responsible for most of the observed dust thermal emission.

Hybrid Simulations of Plasma-Neutral-Dust Interactions at Enceladus

International Nuclear Information System (INIS)

Omidi, N.; Russell, C. T.; Jia, Y. D.; Tokar, R. L.; Farrell, W. M.; Kurth, W. S.; Gurnett, D. A.; Leisner, J. S.

2010-01-01

Through ejection from its southern hemisphere, Enceladus is a dominant source of neutral gas and dust in Saturn's inner magnetosphere. The interaction of the corotating plasma with the gas and dust modifies the plasma environment around Enceladus. We use 3-D hybrid (kinetic ions, fluid electrons) simulations to examine the effects of gas and dust on the nature of the interaction region and use Cassini observations to constrain their properties.

Puff models for simulation of fugitive radioactive emissions in atmosphere

Energy Technology Data Exchange (ETDEWEB)

Costa, Camila P. da, E-mail: camila.costa@ufpel.edu.b [Universidade Federal de Pelotas (UFPel), RS (Brazil). Inst. de Fisica e Matematica. Dept. de Matematica e Estatistica; Pereira, Ledina L., E-mail: ledinalentz@yahoo.com.b [Universidade do Extremo Sul Catarinense (UNESC), Criciuma, SC (Brazil); Vilhena, Marco T., E-mail: vilhena@pq.cnpq.b [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica; Tirabassi, Tiziano, E-mail: t.tirabassi@isac.cnr.i [Institute of Atmospheric Sciences and Climate (CNR/ISAC), Bologna (Italy)

2009-07-01

A puff model for the dispersion of material from fugitive radioactive emissions is presented. For vertical diffusion the model is based on general techniques for solving time dependent advection-diffusion equation: the ADMM (Advection Diffusion Multilayer Method) and GILTT (Generalized Integral Laplace Transform Technique) techniques. The first one is an analytical solution based on a discretization of the Atmospheric Boundary Layer (ABL) in sub-layers where the advection-diffusion equation is solved by the Laplace transform technique. The solution is given in integral form. The second one is a well-known hybrid method that had solved a wide class of direct and inverse problems mainly in the area of Heat Transfer and Fluid Mechanics and the solution is given in series form. Comparisons between values predicted by the models against experimental ground-level concentrations are shown. (author)

Puff models for simulation of fugitive radioactive emissions in atmosphere

International Nuclear Information System (INIS)

Costa, Camila P. da; Vilhena, Marco T.

2009-01-01

A puff model for the dispersion of material from fugitive radioactive emissions is presented. For vertical diffusion the model is based on general techniques for solving time dependent advection-diffusion equation: the ADMM (Advection Diffusion Multilayer Method) and GILTT (Generalized Integral Laplace Transform Technique) techniques. The first one is an analytical solution based on a discretization of the Atmospheric Boundary Layer (ABL) in sub-layers where the advection-diffusion equation is solved by the Laplace transform technique. The solution is given in integral form. The second one is a well-known hybrid method that had solved a wide class of direct and inverse problems mainly in the area of Heat Transfer and Fluid Mechanics and the solution is given in series form. Comparisons between values predicted by the models against experimental ground-level concentrations are shown. (author)

The concentration, source and deposition flux of ammonium and nitrate in atmospheric particles during dust events at a coastal site in northern China

Science.gov (United States)

Qi, Jianhua; Liu, Xiaohuan; Yao, Xiaohong; Zhang, Ruifeng; Chen, Xiaojing; Lin, Xuehui; Gao, Huiwang; Liu, Ruhai

2018-01-01

Asian dust has been reported to carry anthropogenic reactive nitrogen during transport from source areas to the oceans. In this study, we attempted to characterize NH4+ and NO3- in atmospheric particles collected at a coastal site in northern China during spring dust events from 2008 to 2011. Based on the mass concentrations of NH4+ and NO3- in each total suspended particle (TSP) sample, the samples can be classified into increasing or decreasing types. In Category 1, the concentrations of NH4+ and NO3- were 20-440 % higher in dust day samples relative to samples collected immediately before or after a dust event. These concentrations decreased by 10-75 % in the dust day samples in Categories 2 and 3. Back trajectory analysis suggested that multiple factors, such as the transport distance prior to the reception site, the mixing layer depth on the transport route and the residence time across highly polluted regions, might affect the concentrations of NH4+ and NO3-. NH4+ in the dust day samples was likely either in the form of ammonium salts existing separately to dust aerosols or as the residual of incomplete reactions between ammonium salts and carbonate salts. NO3- in the dust day samples was attributed to various formation processes during the long-range transport. The positive matrix factorization (PMF) receptor model results showed that the contribution of soil dust increased from 23 to 36 % on dust days, with decreasing contributions from local anthropogenic inputs and associated secondary aerosols. The estimated deposition flux of NNH4++NO3- varied greatly from event to event; e.g., the dry deposition flux of NNH4++NO3- increased by 9-285 % in Category 1 but decreased by 46-73 % in Category 2. In Category 3, the average dry deposition fluxes of particulate nitrate and ammonium decreased by 46 % and increased by 10 %, respectively, leading to 11-48 % decrease in the fluxes of NNH4++NO3-.

Paleo-dust insights onto dust-climate interactions

Science.gov (United States)

Albani, S.; Mahowald, N. M.

2017-12-01

Mineral dust emissions are affected by changing climate conditions, and in turn dust impacts the atmospheric radiation budget, clouds and biogeochemical cycles. Climate and public health dust-related issues call for attention on the fate of the dust cycle in the future, and the representation of the dust cycle is now part of the strategy of the Paleoclimate Modelling Intercomparison Project phase 4 and the Coupled Model Intercomparison Project phase 6 (PMIP4-CMIP6). Since mineral aerosols are one of the most important natural aerosols, understanding past dust responses to climate in the paleoclimate will allow us to better understand mineral aerosol feedbacks with climate and biogeochemistry in the Anthropocene. Modern observations and paleoclimate records offer the possibility of multiple, complementary views on the global dust cycle, and allow to validate and/or constrain the numerical representation of dust in climate and Earth system models. We present our results from a set of simulations with the Community Earth System Model for different climate states, including present and past climates such as the pre-industrial, the mid-Holocene and the Last Glacial Maximum. A set of simulations including a prognostic dust cycle was thoroughly compared with a wide set of present day observations from different platforms and regions, in order to realistically constrain the magnitude of dust load, surface concentration, deposition, optical properties, and particle size distributions. The magnitude of emissions for past climate regimes was constrained based on compilations of paleodust mass accumulation rates and size distributions, as well as based on information on dust provenance. The comparison with a parallel set of simulations without dust allows estimating the impacts of dust on surface climate. We analyze impacts of dust on the mean and variability of surface temperature and precipitation in each climate state, as well as the impacts that changing dust emissions had

Characteristics of mineral dust impacting the Persian Gulf

Science.gov (United States)

Ahmady-Birgani, Hesam; McQueen, Kenneth G.; Mirnejad, Hassan

2018-02-01

It is generally assumed that severe dust events in western Iran could be responsible for elevated levels of toxic and radioactive elements in the region. Over a period of 5 months, from January 2012 to May 2012, dust particles in the size range PM10 (i.e. chemical compositions of dust and aerosol samples collected during the non-dusty periods and during two severe dust events. Results of ICP-MS analysis of components indicate that during dust events the concentrations of major elements such as Ca, Mg, Al and K increase relative to ambient conditions when Fe and trace elements such as Cu, Cr, Ni, Pb and Zn are in higher proportions. Toxic trace elements that are generally ascribed to human activities, including industrial and urban pollution, are thus proportionately more abundant in the dust under calm conditions than during dust events, when their concentration is diluted by more abundant mineral particles of quartz, calcite and clay. The variability of chemical species during two dust events, noted by tracking the dust plumes in satellite images, was also assessed and the results relate to two different source areas, namely northern Iraq and northwestern Syria.

Investigation of Natural Gas Fugitive Leak Detection Using an Unmanned Aerial Vehicle

Science.gov (United States)

Yang, S.; Talbot, R. W.; Frish, M. B.; Golston, L.; Aubut, N. F.; Zondlo, M. A.

2017-12-01

The U.S is now the world's largest natural gas producer, of which methane (CH4) is the main component. About 2% of the CH4 is lost through fugitive leaks. This research is under the DOE Methane Observation Networks with Innovative Technology to Obtain Reductions (MONITOR) program of ARPA-E. Our sentry measurement system is composed of four state-of-the-art technologies centered around the RMLDTM (Remote Methane Leak Detector). An open path RMLDTM measures column-integrated CH4 concentration that incorporates fluctuations in the vertical CH4 distribution. Based on Backscatter Tunable Diode Laser Absorption Spectroscopy and Small Unmanned Aerial Vehicles, the sentry system can autonomously, consistently and cost-effectively monitor and quantify CH4 leakage from sites associated with natural gas production. This system provides an advanced capability in detecting leaks at hard-to-access sites (e.g., wellheads) compared to traditional manual methods. Automated leak detecting and reporting algorithms combined with wireless data link implement real-time leak information reporting. Early data were gathered to set up and test the prototype system, and to optimize the leak localization and calculation strategies. The flight pattern is based on a raster scan which can generate interpolated CH4 concentration maps. The localization and quantification algorithms can be derived from the plume images combined with wind vectors. Currently, the accuracy of localization algorithm can reach 2 m and the calculation algorithm has a factor of 2 accuracy. This study places particular emphasis on flux quantification. The data collected at Colorado and Houston test fields were processed, and the correlation between flux and other parameters analyzed. Higher wind speeds and lower wind variation are preferred to optimize flux estimation. Eventually, this system will supply an enhanced detection capability to significantly reduce fugitive CH4 emissions in the natural gas industry.

Influences of natural emission sources (wildfires and Saharan dust) on the urban organic aerosol in Barcelona (Western Mediterranean Basis) during a PM event.

Science.gov (United States)

van Drooge, Barend L; Lopez, Jordi F; Grimalt, Joan O

2012-11-01

The urban air quality in Barcelona in the Western Mediterranean Basin is characterized by overall high particulate matter (PM) concentrations, due to intensive local anthropogenic emissions and specific meteorological conditions. Moreover, on several days, especially in summer, natural PM sources, such as long-range transported Saharan dust from Northern Africa or wildfires on the Iberian Peninsula and around the Mediterranean Basin, may influence the levels and composition of the organic aerosol. In the second half of July 2009, daily collected PM(10) filter samples in an urban background site in Barcelona were analyzed on organic tracer compounds representing several emission sources. During this period, an important PM peak event was observed. Individual organic compound concentrations increased two to five times during this event. Although highest increase was observed for the organic tracer of biomass burning, the contribution to the organic aerosol was estimated to be around 6 %. Organic tracers that could be related to Saharan dust showed no correlation with the PM and OC levels, while this was the case for those related to fossil fuel combustion from traffic emissions. Moreover, a change in the meteorological conditions gave way to an overall increase of the urban background contamination. Long-range atmospheric transport of organic compounds from primary emissions sources (i.e., wildfires and Saharan dust) has a relatively moderate impact on the organic aerosol in an urban area where the local emissions are dominating.

Respirable dust measured downwind during rock dust application.

Science.gov (United States)

Harris, M L; Organiscak, J; Klima, S; Perera, I E

2017-05-01

The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH's Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners' exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device.

Dust in Snow in the Colorado River Basin: Spatial Variability in Dust Concentrations, Radiative Forcing, and Snowmelt Rates

Science.gov (United States)

Skiles, M.; Painter, T.; Deems, J. S.; Landry, C.; Bryant, A.

2012-12-01

Since the disturbance of the western US that began with the Anglo settlement in the mid 19th century, the mountain snow cover of the Colorado River Basin (CRB) has been subject to five-fold greater dust loading. This dust deposition accelerates snowmelt through its direct reduction of albedo and its further reduction of albedo by accelerating the growth of snow effective grain size. We have previously quantified the impacts of dust in snow using a 6-year record of dust concentration and energy balance fluxes at the alpine and subalpine towers in the Senator Beck Basin Study Area (SBBSA), San Juan Mountains in southwestern Colorado, USA. Dust loading exhibited interannual variability, and end of year dust concentrations were not necessarily related to the number of dust deposition events. Radiative forcing enhanced springtime melt by 21 to 51 days with the magnitude of advanced loss being linearly related to total dust concentration at the end of snow cover. To expand our understanding of dust on snow deposition patterns we utilize collections of dust concentration at the Colorado Dust on Snow (CODOS) study sites, established in 2009 along the western side of the CRB, to assess spatial variability in dust loading. In situ sampling of dust stratigraphy and concentration occurs twice each season, once over peak snow water equivalent (15 April), and again during melt (15 May). Dust loading occurs at all sites; dust concentrations are always higher in May, vary between sites, and the highest and lowest dust years were 2009 and 2012, respectively. In the absence of regular sampling and energy balance instrumentation these sites do not allow us to quantify the advanced melt due to dust. To facilitate this a new energy balance site, Grand Mesa Study plot (GMSP), was established for water year 2010 in west central Colorado, 150 km north of SBBSA. Back trajectories indicate similar Colorado Plateau dust sources at both SBBSA and GMSP, yet GMSP exhibits slightly lower dust

Lead isotopes combined with a sequential extraction procedure for source apportionment in the dry deposition of Asian dust and non-Asian dust

International Nuclear Information System (INIS)

Lee, Pyeong-Koo; Yu, Soonyoung

2016-01-01

Lead isotopic compositions were determined in leachates that were generated using sequential extractions of dry deposition samples of Asian dust (AD) and non-Asian dust (NAD) and Chinese desert soils, and used to apportion Pb sources. Results showed significant differences in "2"0"6Pb/"2"0"7Pb and "2"0"6Pb/"2"0"4Pb isotopic compositions in non-residual fractions between the dry deposition samples and the Chinese desert soils while "2"0"6Pb/"2"0"7Pb and "2"0"6Pb/"2"0"4Pb isotopic compositions in residual fraction of the dry deposition of AD and NAD were similar to the mean "2"0"6Pb/"2"0"7Pb and "2"0"6Pb/"2"0"4Pb in residual fraction of the Alashan Plateau soil. These results indicate that the geogenic materials of the dry deposition of AD and NAD were largely influenced by the Alashan Plateau soil, while the secondary sources of the dry deposition were different from those of the Chinese desert soils. In particular, the lead isotopic compositions in non-residual fractions of the dry deposition were homogenous, which implies that the non-residual four fractions (F1 to F4) shared the primary anthropogenic origin. "2"0"6Pb/"2"0"7Pb values and the predominant wind directions in the study area suggested that airborne particulates of heavily industrialized Chinese cities were one of the main Pb sources. Source apportionment calculations showed that the average proportion of anthropogenic Pb in the dry deposition of AD and NAD was 87% and 95% respectively in total Pb extraction, 92% and 97% in non-residual fractions, 15% and 49% in residual fraction. Approximately 81% and 80% of the anthropogenic Pb was contributed by coal combustion in China in the dry deposition of AD and NAD respectively while the remainder was derived from industrial Pb contamination. The research result proposes that sequential extractions with Pb isotope analysis are a useful tool for the discrimination of anthropogenic and geogenic origins in highly contaminated AD and NAD. - Highlights: �

78 FR 32131 - Revision to the Washington State Implementation Plan; Tacoma-Pierce County Nonattainment Area

Science.gov (United States)

2013-05-29

... speciation monitor and found no evidence of increasing fugitive dust trends from 2008 to 2011. See Tacoma PMF... request for these documents. For the convenience of the reader these background documents have been added...

PREVAILING DUST-TRANSPORT DIRECTIONS ON COMET 67P/CHURYUMOV–GERASIMENKO

Energy Technology Data Exchange (ETDEWEB)

Kramer, Tobias; Noack, Matthias [Konrad-Zuse-Zentrum für Informationstechnik, Takustrasse 7, D-14195 Berlin (Germany)

2015-11-10

Dust transport and deposition behind larger boulders on the comet 67P/Churyumov–Gerasimenko (67P/C–G) have been observed by the Rosetta mission. We present a mechanism for dust-transport vectors based on a homogeneous surface activity model incorporating in detail the topography of 67P/C–G. The combination of gravitation, gas drag, and Coriolis force leads to specific dust transfer pathways, which for higher dust velocities fuel the near-nucleus coma. By distributing dust sources homogeneously across the whole cometary surface, we derive a global dust-transport map of 67P/C–G. The transport vectors are in agreement with the reported wind-tail directions in the Philae descent area.

Lead in Chinese villager house dust: Geographical variation and influencing factors.

Science.gov (United States)

Bi, Xiangyang; Liu, Jinling; Han, Zhixuan; Yang, Wenlin

2015-12-01

House dust has been recognized as an important contributor to Pb exposure of children. Here we conducted a comprehensive study to investigate geographical variation of Pb in Chinese villager house dust. The influences of outdoor soil Pb concentrations, dates of construction, house decoration materials, heating types, and site specific pollution on Pb concentrations in house dust were evaluated. The concentrations of Pb in 477 house dust samples collected from twenty eight areas throughout China varied from 12 to 2510 mg/kg, with a median concentration of 42 mg/kg. The median Pb concentrations in different geographical areas ranged from 16 (Zhangjiakou, Hebei) to 195 mg/kg (Loudi, Hunan). No correlations were found between the house dust Pb concentrations and the age of houses, as well as house decoration materials. Whereas outdoor soil, coal combustion, and site specific pollution may be potential Pb sources. Principal component analysis (PCA) confirmed that elemental compositions of the house dust were controlled by both anthropogenic and geogenic sources. Using scanning electron microscopy (SEM), the Pb bearing particles in the house dust were also studied. Copyright © 2015 Elsevier Ltd. All rights reserved.

Preliminary Assessment of Health Risks of Potentially Toxic Elements in Settled Dust over Beijing Urban Area

Directory of Open Access Journals (Sweden)

Dejun Wan

2016-05-01

Full Text Available To examine levels, health risks, sources, and spatial distributions of potentially toxic elements in settled dust over Beijing urban area, 62 samples were collected mostly from residential building outdoor surfaces, and their <63 μm fractions were measured for 12 potentially toxic elements. The results show that V, Cr, Mn, Co, Ni, and Ba in dust are from predominantly natural sources, whereas Cu, Zn, As, Cd, Sb, and Pb mostly originate from anthropogenic sources. Exposure to these elements in dust has significant non-cancer risks to children but insignificant to adults. Cancer risks of Cr, Co, Ni, As, and Cd via inhalation and dermal contact are below the threshold of 10−6–10−4 but As via dust ingestion shows a tolerable risk. The non-cancer risks to children are contributed mainly (75% by As, Pb, and Sb, and dominantly (92% via dust ingestion, with relatively higher risks mainly occurring in the eastern and northeastern Beijing urban areas. Although Cd, Zn, and Cu in dust are heavily affected by anthropogenic sources, their health risks are insignificant. Source appointments suggest that coal burning emissions, the dominant source of As, are likely the largest contributors to the health risk, and traffic-related and industrial emissions are also important because they contribute most of the Pb and Sb in dust.

Aerosol-ozone correlations during dust transport episodes

Directory of Open Access Journals (Sweden)

P. Bonasoni

2004-01-01

Full Text Available Its location in the Mediterranean region and its physical characteristics render Mt. Cimone (44°11′ N, 10°42′ E, the highest peak of the Italian northern Apennines (2165 m asl, particularly suitable to study the transport of air masses from the north African desert area to Europe. During these northward transports 12 dust events were registered in measurements of the aerosol concentration at the station during the period June–December 2000, allowing the study of the impact of mineral dust transports on free tropospheric ozone concentrations, which were also measured at Mt. Cimone. Three-dimensional backward trajectories were used to determine the air mass origin, while TOMS Aerosol Index data for the Mt. Cimone area were used to confirm the presence of absorbing aerosol over the measurement site. A trajectory statistical analysis allowed identifying the main source areas of ozone and aerosols. The analysis of these back trajectories showed that central Europe and north and central Italy are the major pollution source areas for ozone and fine aerosol, whereas the north African desert regions were the most important source areas for coarse aerosol and low ozone concentrations. During dust events, the Mt. Cimone mean volume concentration for coarse particles was 6.18 µm3/cm3 compared to 0.63 µm3/cm3 in dust-free conditions, while the ozone concentrations were 4% to 21% lower than the monthly mean background values. Our observations show that surface ozone concentrations were lower than the background values in air masses coming from north Africa, and when these air masses were also rich in coarse particles, the lowest ozone values were registered. Moreover, preliminary results on the possible impact of the dust events on PM10 and ozone values measured in Italian urban and rural areas showed that during the greater number of the considered dust events, significant PM10 increases and ozone decreases have occurred in the Po valley.

Dust Studies in DIII-D and TEXTOR

International Nuclear Information System (INIS)

Rudakov, D.L.; Litnovsky, A.; West, W.P.; Yu, J.H.; Boedo, J.A.; Bray, B.D.; Brezinsek, S.; Brooks, N.H.; Fenstermacher, M.E.; Groth, M.; Hollmann, E.M.; Huber, A.; Hyatt, A.W.; Krasheninnikov, S.I.; Lasnier, C.J.; Moyer, R.A.; Pigarov, A.Y.; Philipps, V.; Pospieszczyk, A.; Smirnov, R.D.; Sharpe, J.P.; Solomon, W.M.; Watkins, J.G.; Wong, C.C.

2009-01-01

Studies of naturally occurring and artificially introduced carbon dust are conducted in DIII-D and TEXTOR. In DIII-D, dust does not present operational concerns except immediately after entry vents. Submicron sized dust is routinely observed using Mie scattering from a Nd:Yag laser. The source is strongly correlated with the presence of Type I edge localized modes (ELMs). Larger size (0.005-1 mm diameter) dust is observed by optical imaging, showing elevated dust levels after entry vents. Inverse dependence of the dust velocity on the inferred dust size is found from the imaging data. Direct heating of the dust particles by the neutral beam injection (NBI) and acceleration of dust particles by the plasma flows are observed. Energetic plasma disruptions produce significant amounts of dust. Large flakes or debris falling into the plasma may result in a disruption. Migration of pre-characterized carbon dust is studied in DIII-D and TEXTOR by introducing micron-size dust in plasma discharges. In DIII-D, a sample holder filled with ∼30 mg of dust is introduced in the lower divertor and exposed to high-power ELMing H-mode discharges with strike points swept across the divertor floor. After a brief exposure (∼0.1 s) at the outer strike point, part of the dust is injected into the plasma, raising the core carbon density by a factor of 2-3 and resulting in a twofold increase of the radiated power. In TEXTOR, instrumented dust holders with 1-45 mg of dust are exposed in the scrape-off layer 0-2 cm radially outside of the last closed flux surface in discharges heated with neutral beam injection (NBI) power of 1.4 MW. At the given configuration of the launch, the dust did not penetrate the core plasma and only moderately perturbed the edge plasma, as evidenced by an increase of the edge carbon content.

Estimation of micrometeorites and satellite dust flux surrounding Mars in the light of MAVEN results

Science.gov (United States)

Pabari, J. P.; Bhalodi, P. J.

2017-05-01

Recently, MAVEN observed dust around Mars from ∼150 km to ∼1000 km and it is a puzzling question to the space scientists about the presence of dust at orbital altitudes and about its source. A continuous supply of dust from various sources could cause existence of dust around Mars and it is expected that the dust could mainly be from either the interplanetary source or the Phobos/Deimos. We have studied incident projectiles or micrometeorites at Mars using the existing model, in this article. Comparison of results with the MAVEN results gives a new value of the population index S, which is reported here. The index S has been referred in a power law model used to describe the number of impacting particles on Mars. In addition, the secondary ejecta from natural satellites of Mars can cause a dust ring or torus around Mars and remain present for its lifetime. The dust particles whose paths are altered by the solar wind over its lifetime, could present a second plausible source of dust around Mars. We have investigated escaping particles from natural satellites of Mars and compared with the interplanetary dust flux estimation. It has been found that flux rate at Mars is dominated (∼2 orders of magnitude higher) by interplanetary particles in comparison with the satellite originated dust. It is inferred that the dust at high altitudes of Mars could be interplanetary in nature and our expectation is in agreement with the MAVEN observation. As a corollary, the mass loss from Martian natural satellites is computed based on the surface erosion by incident projectiles.

Role of Chinese wind-blown dust in enhancing environmental pollution in Metropolitan Seoul

Energy Technology Data Exchange (ETDEWEB)

Kim, Wonnyon [Department of Earth and Environmental Sciences, Korea University, Seoul 136-713 (Korea, Republic of); Doh, Seong-Jae [Department of Earth and Environmental Sciences, Korea University, Seoul 136-713 (Korea, Republic of)], E-mail: sjdoh@korea.ac.kr; Yu, Yongjae; Lee, Meehye [Department of Earth and Environmental Sciences, Korea University, Seoul 136-713 (Korea, Republic of)

2008-05-15

A suite of rock magnetic experiments and intensive microscopic observations were carried out on Asian dust deposits in Seoul, Korea, collected on 19 and 23 March 2002, 9 April 2002 and 12 April 2003. Desert-sand and loess from the dust source regions in China were also analyzed as a comparison. Asian dust showed a higher magnetic concentration than the source region samples, indicating a significant influx of magnetic particles into Asian dust had occurred during its transportation. Electron microscopy identified carbon-bearing iron-oxides as the added material. These iron-oxides were likely to have been produced by anthropogenic pollution (fossil fuel combustion) while the wind-blown dusts passing across the industrial areas of eastern China and western Korea. Such wind-paths were confirmed by a simulation of the air-mass trajectories. The magnetic technique appears to be useful for determining the anthropogenic pollution of Asian dust. - Magnetic quantification of anthropogenic pollution of Asian dust.

Role of Chinese wind-blown dust in enhancing environmental pollution in Metropolitan Seoul

International Nuclear Information System (INIS)

Kim, Wonnyon; Doh, Seong-Jae; Yu, Yongjae; Lee, Meehye

2008-01-01

A suite of rock magnetic experiments and intensive microscopic observations were carried out on Asian dust deposits in Seoul, Korea, collected on 19 and 23 March 2002, 9 April 2002 and 12 April 2003. Desert-sand and loess from the dust source regions in China were also analyzed as a comparison. Asian dust showed a higher magnetic concentration than the source region samples, indicating a significant influx of magnetic particles into Asian dust had occurred during its transportation. Electron microscopy identified carbon-bearing iron-oxides as the added material. These iron-oxides were likely to have been produced by anthropogenic pollution (fossil fuel combustion) while the wind-blown dusts passing across the industrial areas of eastern China and western Korea. Such wind-paths were confirmed by a simulation of the air-mass trajectories. The magnetic technique appears to be useful for determining the anthropogenic pollution of Asian dust. - Magnetic quantification of anthropogenic pollution of Asian dust

Dust Studies in DIII-D and TEXTOR

International Nuclear Information System (INIS)

Rudakov, D.; Litnovsky, A.; West, W.; Yu, J.; Boedo, J.; Bray, B.; Brezinsek, S.; Brooks, N.; Fenstermacher, M.; Groth, M.; Hollmann, E.; Huber, A.; Hyatt, A.; Krasheninnikov, S.; Lasnier, C.; Moyer, R.; Pigarov, A.; Philipps, V.; Pospieszezyk, A.; Smirnov, R.; Sharpe, J.; Solomon, W.; Watkins, J.; Wong, C.

2008-01-01

Studies of naturally occurring and artificially introduced carbon dust are conducted in DIII-D and TEXTOR. In DIII-D, dust does not present operational concerns except immediately after entry vents. Energetic plasma disruptions produce significant amounts of dust. However, dust production by disruptions alone is insufficient to account for the estimated in-vessel dust inventory in DIII-D. Submicron sized dust is routinely observed using Mie scattering from a Nd:Yag laser. The source is strongly correlated with the presence of Type I edge localized modes (ELMs). Larger size (0.005-1 mm diameter) dust is observed by optical imaging, showing elevated dust levels after entry vents. Inverse dependence of the dust velocity on the inferred dust size is found from the imaging data. Migration of pre-characterized carbon dust is studied in DIII-D and TEXTOR by injecting micron-size dust in plasma discharges. In DIII-D, a sample holder filled with ∼30 mg of dust is introduced in the lower divertor and exposed to high-power ELMing H-mode discharges with strike points swept across the divertor floor. After a brief exposure (∼0.1 s) at the outer strike point, part of the dust is injected into the plasma, raising the core carbon density by a factor of 2-3 and resulting in a twofold increase of the radiated power. Individual dust particles are observed moving at velocities of 10-100 m/s, predominantly in the toroidal direction, consistent with the drag force from the deuteron flow and in agreement with modeling by the 3D DustT code. In TEXTOR, instrumented dust holders with 1-45 mg of dust are exposed in the scrape-off layer 0-2 cm radially outside of the last closed flux surface in discharges heated with neutral beam injection (NBI) power of 1.4 MW. Dust is launched either in the beginning of a discharge or at the initiation of NBI, preferentially in a direction perpendicular to the toroidal magnetic field. At the given configuration of the launch, the dust did not penetrate

Multiregional environmental comparison of fossil fuel power generation-Assessment of the contribution of fugitive emissions from conventional and unconventional fossil resources

NARCIS (Netherlands)

Bouman, Evert A.; Ramirez, Andrea; Hertwich, Edgar G.

2015-01-01

In this paper we investigate the influence of fugitive methane emissions from coal, natural gas, and shale gas extraction on the greenhouse gas (GHG) impacts of fossil fuel power generation through its life cycle. A multiregional hybridized life cycle assessment (LCA) model is used to evaluate

Chemical characterization and receptor modeling of PM10 in the surroundings of the opencast lignite mines of Western Macedonia, Greece.

Science.gov (United States)

Samara, Constantini; Argyropoulos, George; Grigoratos, Theodoros; Kouras, Αthanasios; Manoli, Εvangelia; Andreadou, Symela; Pavloudakis, Fragkiskos; Sahanidis, Chariton

2018-05-01

The Western Macedonian Lignite Center (WMLC) in northwestern Greece is the major lignite center in the Balkans feeding four major power plants of total power exceeding 4 GW. Concentrations of PM 10 (i.e., particulate matters with diameters ≤10 μm) are the main concern in the region, and the high levels observed are often attributed to the activities related to power generation. In this study, the contribution of fugitive dust emissions from the opencast lignite mines to the ambient levels of PM 10 in the surroundings was estimated by performing chemical mass balance (CMB) receptor modeling. For this purpose, PM 10 samples were concurrently collected at four receptor sites located in the periphery of the mine area during the cold and the warm periods of the year (November-December 2011 and August-September 2012), and analyzed for a total of 26 macro- and trace elements and ionic species (sulfate, nitrate, chloride). The robotic chemical mass balance (RCMB) model was employed for source identification/apportionment of PM 10 at each receptor site using as inputs the ambient concentrations and the chemical profiles of various sources including the major mine operations, the fly ash escaping the electrostatic filters of the power plants, and other primary and secondary sources. Mean measured PM 10 concentrations at the different sites ranged from 38 to 72 μg m -3 . The estimated total contribution of mines ranged between 9 and 22% in the cold period increasing to 36-42% in the dry warm period. Other significant sources were vehicular traffic, biomass burning, and secondary sulfate and nitrate aerosol. These results imply that more efficient measures to prevent and suppress fugitive dust emissions from the mines are needed.

House dust in seven Danish offices

Science.gov (United States)

Mølhave, L.; Schneider, T.; Kjærgaard, S. K.; Larsen, L.; Norn, S.; Jørgensen, O.

Floor dust from Danish offices was collected and analyzed. The dust was to be used in an exposure experiment. The dust was analyzed to show the composition of the dust which can be a source of airborne dust indoors. About 11 kg of dust from vacuum cleaner bags from seven Danish office buildings with about 1047 occupants (12 751 m 2) was processed according to a standardized procedure yielding 5.5 kg of processed bulk dust. The bulk dust contained 130.000-160.000 CFU g -1 microorganisms and 71.000-90.000 CFU g -1 microfungi. The content of culturable microfungi was 65-123 CFU 30 g -1 dust. The content of endotoxins ranged from 5.06-7.24 EU g -1 (1.45 ng g -1 to 1.01 ng g -1). Allergens (ng g -1) were from 147-159 (Mite), 395-746 (dog) and 103-330 (cat). The macro molecular organic compounds (the MOD-content) varied from 7.8-9.8 mg g -1. The threshold of release of histamine from basophil leukocytes provoked by the bulk dust was between 0.3 and 1.0 mg ml -1. The water content was 2% (WGT) and the organic fraction 33%. 6.5-5.9% (dry) was water soluble. The fiber content was less than 0.2-1.5% (WGT) and the desorbable VOCs was 176-319 μg g -1. Most of the VOC were aldehydes. However, softeners for plastic (DBP and DEHP) were present. The chemical composition includes human and animal skin fragments, paper fibers, glass wool, wood and textilefibers and inorganic and metal particles. The sizes ranged from 0.001-1 mm and the average specific density was 1.0 g m -3. The bulk dust was resuspended and injected into an exposure chamber. The airborne dust was sampled and analyzed to illustrate the exposures that can result from sedimented dirt and dust. The airborne dust resulting from the bulk dust reached concentrations ranging from 0.26-0.75 mg m -3 in average contained 300-170 CFU m -3. The organic fraction was from 55-70% and the water content about 2.5% (WGT). The content of the dust was compared to the similar results reported in the literature and its toxic potency is

Quantifying local-scale dust emission from the Arabian Red Sea coastal plain

KAUST Repository

Anisimov, Anatolii

2017-01-23

Dust plumes emitted from the narrow Arabian Red Sea coastal plain are often observed on satellite images and felt in local population centers. Despite its relatively small area, the coastal plain could be a significant dust source; however, its effect is not well quantified as it is not well approximated in global or even regional models. In addition, because of close proximity to the Red Sea, a significant amount of dust from the coastal areas could be deposited into the Red Sea and serve as a vital component of the nutrient balance of marine ecosystems. In the current study, we apply the offline Community Land Model version 4 (CLM4) to better quantify dust emission from the coastal plain during the period of 2009-2011. We verify the spatial and temporal variability in model results using independent weather station reports. We also compare the results with the MERRA Aerosol Reanalysis (MERRAero). We show that the best results are obtained with 1 km model spatial resolution and dust source function based on Meteosat Second Generation Spinning Enhanced Visible and InfraRed Imager (SEVIRI) measurements. We present the dust emission spatial pattern, as well as estimates of seasonal and diurnal variability in dust event frequency and intensity, and discuss the emission regime in the major dust generation hot spot areas. We demonstrate the contrasting seasonal dust cycles in the northern and southern parts of the coastal plain and discuss the physical mechanisms responsible for dust generation. This study provides the first estimates of the fine-scale spatial and temporal distribution of dust emissions from the Arabian Red Sea coastal plain constrained by MERRAero and short-term WRF-Chem simulations. The estimate of total dust emission from the coastal plain, tuned to fit emissions in MERRAero, is 7.5 ± 0.5 Mt a. Small interannual variability indicates that the study area is a stable dust source. The mineralogical composition analysis shows that the coastal plain

Quantifying local-scale dust emission from the Arabian Red Sea coastal plain

KAUST Repository

Anisimov, Anatolii; Tao, Weichun; Stenchikov, Georgiy L.; Kalenderski, Stoitchko; Jish Prakash, P.; Yang, Zong Liang; Shi, Mingjie

2017-01-01

Dust plumes emitted from the narrow Arabian Red Sea coastal plain are often observed on satellite images and felt in local population centers. Despite its relatively small area, the coastal plain could be a significant dust source; however, its effect is not well quantified as it is not well approximated in global or even regional models. In addition, because of close proximity to the Red Sea, a significant amount of dust from the coastal areas could be deposited into the Red Sea and serve as a vital component of the nutrient balance of marine ecosystems. In the current study, we apply the offline Community Land Model version 4 (CLM4) to better quantify dust emission from the coastal plain during the period of 2009-2011. We verify the spatial and temporal variability in model results using independent weather station reports. We also compare the results with the MERRA Aerosol Reanalysis (MERRAero). We show that the best results are obtained with 1 km model spatial resolution and dust source function based on Meteosat Second Generation Spinning Enhanced Visible and InfraRed Imager (SEVIRI) measurements. We present the dust emission spatial pattern, as well as estimates of seasonal and diurnal variability in dust event frequency and intensity, and discuss the emission regime in the major dust generation hot spot areas. We demonstrate the contrasting seasonal dust cycles in the northern and southern parts of the coastal plain and discuss the physical mechanisms responsible for dust generation. This study provides the first estimates of the fine-scale spatial and temporal distribution of dust emissions from the Arabian Red Sea coastal plain constrained by MERRAero and short-term WRF-Chem simulations. The estimate of total dust emission from the coastal plain, tuned to fit emissions in MERRAero, is 7.5 ± 0.5 Mt a. Small interannual variability indicates that the study area is a stable dust source. The mineralogical composition analysis shows that the coastal plain

Radioactive dust concentration around the Ranger uranium mine

International Nuclear Information System (INIS)

Kavasnicka, Jiri.

1988-07-01

Environmental dust sampling and wind direction/velocity monitory were carried out between July and November 1987 at five points around the Ranger Uranium Mines project near Jabiru, Northern Territory. The measured radioactive dust alpha activities in the air were used to calculate the radioactive dust source-term and develop a site-specific air dispersion model which takes the depletion of the dust plume into account. The above model was used to estimate the effective committed dose equivalent as 15 μSv/year to children in Jabiru East. This corresponds to an increase of 2.6 x 10 -4 Bq. m -3 in the annual average dust alpha activity above the natural background. The dose to the children in Jabiru is about 5 μSv/year, so that the critical group of the public is in Jabiru East. 12 refs., 11 tabs., 2 maps

Charge-fluctuation-induced heating of dust particles in a plasma.

Science.gov (United States)

Vaulina, O S; Khrapak, S A; Nefedov, A P; Petrov, O F

1999-11-01

Random charge fluctuations are always present in dusty plasmas due to the discrete nature of currents charging the dust particle. These fluctuations can be a reason for the heating of the dust particle system. Such unexpected heating leading to the melting of the dust crystals was observed recently in several experiments. In this paper we show by analytical evaluations and numerical simulation that charge fluctuations provide an effective source of energy and can heat the dust particles up to several eV, in conditions close to experimental ones.

Health Effects of Petroleum Coke

Science.gov (United States)

Significant quantities of fugitive dust from pet coke storage and handling operations present a health risk. EPA’s research suggests that petcoke does not pose a different health risk than similar-sized particulate matter (PM10).

Common Warm Dust Temperatures Around Main Sequence Stars

Science.gov (United States)

Morales, Farisa; Rieke, George; Werner, Michael; Stapelfeldt, Karl; Bryden, Geoffrey; Su, Kate

2011-01-01

We compare the properties of warm dust emission from a sample of main-sequence A-type stars (B8-A7) to those of dust around solar-type stars (F5-KO) with similar Spitzer Space Telescope Infrared Spectrograph/MIPS data and similar ages. Both samples include stars with sources with infrared spectral energy distributions that show evidence of multiple components. Over the range of stellar types considered, we obtain nearly the same characteristic dust temperatures (∼ 190 K and ∼60 K for the inner and outer dust components, respectively)-slightly above the ice evaporation temperature for the inner belts. The warm inner dust temperature is readily explained if populations of small grains are being released by sublimation of ice from icy planetesimals. Evaporation of low-eccentricity icy bodies at ∼ 150 K can deposit particles into an inner/warm belt, where the small grains are heated to dust Temperatures of -190 K. Alternatively, enhanced collisional processing of an asteroid belt-like system of parent planetesimals just interior to the snow line may account for the observed uniformity in dust temperature. The similarity in temperature of the warmer dust across our B8-KO stellar sample strongly suggests that dust-producing planetesimals are not found at similar radial locations around all stars, but that dust production is favored at a characteristic temperature horizon.

Road dust from pavement wear and traction sanding

Energy Technology Data Exchange (ETDEWEB)

Kupiainen, K.

2007-07-01

Vehicles affect the concentrations of ambient airborne particles through exhaust emissions, but particles are also formed in the mechanical processes in the tire-road interface, brakes, and engine. Particles deposited on or in the vicinity of the road may be re-entrained, or resuspended, into air through vehicle-induced turbulence and shearing stress of the tires. A commonly used term for these particles is 'road dust'. The processes affecting road dust emissions are complex and currently not well known. Road dust has been acknowledged as a dominant source of PM10 especially during spring in the sub-arctic urban areas, e.g. in Scandinavia, Finland, North America and Japan. The high proportion of road dust in sub-arctic regions of the world has been linked to the snowy winter conditions that make it necessary to use traction control methods. Traction control methods include dispersion of traction sand, melting of ice with brine solutions, and equipping the tires with either metal studs (studded winter tires), snow chains, or special tire design (friction tires). Several of these methods enhance the formation of mineral particles from pavement wear and/or from traction sand that accumulate in the road environment during winter. When snow and ice melt and surfaces dry out, traffic-induced turbulence makes some of the particles airborne. A general aim of this study was to study processes and factors underlying and affecting the formation and emissions of road dust from paved road surfaces. Special emphasis was placed on studying particle formation and sources during tire road interaction, especially when different applications of traction control, namely traction sanding and/or winter tires were in use. Respirable particles with aerodynamic diameter below 10 micrometers (PM10) have been the main concern, but other size ranges and particle size distributions were also studied. The following specific research questions were addressed: (i) How do traction

The Origin and Evolution of Interstellar Dust in the Local and High-redshift Universe

Science.gov (United States)

Dwek, Eliahu

2012-01-01

In this talk I will begin by reviewing our current state of knowledge regarding the origin and evolution of dust in the local solar neighborhood. using chemical evolution models, I will discuss their many different input parameters and their uncertainties. An important consequence of these models is the delayed injection of dust from AGB stars, compared to supernova-condensed dust, into the interstellar medium. I will show that these stellar evolutionary effects on dust composition are manifested in the infrared spectra of local galaxies. The delayed production of dust in AGB stars has also important consequences for the origin of the large amount of dust detected in high-redshift galaxies, when the universe was less that approx. 1 Gyr old. Supernovae may have been the only viable dust sources in those galaxies. Recent observations of sN1987a show a significant mass of dust in the ejecta of this SN. Is that production rate high enough to account for the observed dust mass in these galaxies? If not, what are the alternative viable sources of dust, and how do they depend on the nature of the galaxy (starburst or AGN) and its star formation history .

Analysis of synoptic situation for dust storms in Iraq

Energy Technology Data Exchange (ETDEWEB)

Al-Jumaily, Kais J.; Ibrahim, Morwa K. [Department of Atmospheric Sciences, College of Science, Al-Mustansiriyah University, Baghdad (Iraq)

2013-07-01

Dust storms are considered major natural disasters that cause many damages to society and environment in Iraq and surrounded deserted regions. The aim of this research is to analyze and study the synoptic patterns leading to the formation of dust storms in Iraq. Analysis are based on satellite images, aerosols index and synoptic weather maps. Two severe dust storms occurred over Iraq on February 22, 2010, and on December 10, 2011 were analyzed. The results showed that dust storms form when a low-pressure system forms over Iran causing Shamal winds blow; they carry cool air from that region towards warmer regions like eastern Syria and Iraq. In some cases, this low-pressure system is followed by a high-pressure system brining more cold air to the region and pushing dust toward south. Dust storms are initiated from source regions near Iraq-Syria borders by the existence of negative vertical velocity, which causes dust particles to be lifted upwards, and the strong westerly wind drives dust to travel eastward.

Control of dust production in ITER

International Nuclear Information System (INIS)

Rodriguez-Rodrigo, L.; Ciattaglia, S.; Elbez-Uzan, J.

2006-01-01

In the last years dust has been observed in a number of fusion devices and is being studied more in detail for understanding in particular the physical phenomena related to its formation, its composition, physical and chemical characteristics, and the amount of produced dust. The extrapolation of dust formation to ITER predicts (with large error bars), a large mass of dust production with a scattered size distribution. To evaluate the impact of dust on safety, assumptions have also been made on radionuclide inventory, and mobility in off-normal events, as well as any postulated contributions the dust may make to effluents or accidental releases. Solid activation products in structures are generally not readily mobilisable in incidental and accidental situations, so that activated dust, tritium and activated corrosions products are the important in-vessel source terms in postulated scenarios that assume a mobilisation and release of some fraction of this inventory. Such a release would require the simultaneous leak or bypass of several robust confinement barriers. Further concerns for dust may be the potential for chemical reactions between dust and coolant in the event of an in-vessel leak, and the theoretical possibility of a dust explosion, either of which could in principle cause a pressure rise that challenges one or more of the confinement barriers. Although these hazards can - and will - be controlled by other measures in the ITER design, application of the principle of Defence in Depth dictates that the dust inventory should also be minimised and controlled to prevent the potential hazard. A well-coordinated R-and-D programme is required to support this dust production control. This document provides from the safety point of view, an overview of existing data given in '' Dossier d'Options de Surete '', the first safety report presented in 2001 to the French Safety Authorities, and ITER documents; it also gathers information on status of studies on activated

Density currents as a desert dust mobilization mechanism

Directory of Open Access Journals (Sweden)

S. Solomos

2012-11-01

Full Text Available The formation and propagation of density currents are well studied processes in fluid dynamics with many applications in other science fields. In the atmosphere, density currents are usually meso-β/γ phenomena and are often associated with storm downdrafts. These storms are responsible for the formation of severe dust episodes (haboobs over desert areas. In the present study, the formation of a convective cool pool and the associated dust mobilization are examined for a representative event over the western part of Sahara desert. The physical processes involved in the mobilization of dust are described with the use of the integrated atmospheric-air quality RAMS/ICLAMS model. Dust is effectively produced due to the development of near surface vortices and increased turbulent mixing along the frontal line. Increased dust emissions and recirculation of the elevated particles inside the head of the density current result in the formation of a moving "dust wall". Transport of the dust particles in higher layers – outside of the density current – occurs mainly in three ways: (1 Uplifting of preexisting dust over the frontal line with the aid of the strong updraft (2 Entrainment at the upper part of the density current head due to turbulent mixing (3 Vertical mixing after the dilution of the system. The role of the dust in the associated convective cloud system was found to be limited. Proper representation of convective processes and dust mobilization requires the use of high resolution (cloud resolving model configuration and online parameterization of dust production. Haboob-type dust storms are effective dust sources and should be treated accordingly in dust modeling applications.

Particulate matter over a seven year period in urban and rural areas within, proximal and far from mining and power station operations in Greece.

Science.gov (United States)

Triantafyllou, A G; Zoras, S; Evagelopoulos, V

2006-11-01

Lignite mining operations and lignite-fired power stations result in major particulate pollution (fly ash and fugitive dust) problems in the areas surrounding these activities. The problem is more complicated, especially, for urban areas located not far from these activities, due to additional contribution from the urban pollution sources. Knowledge of the distribution of airborne particulate matter into size fraction has become an increasing area of focus when examining the effects of particulate pollution. On the other hand, airborne particle concentration measurements are useful in order to assess the air pollution levels based on national and international air quality standards. These measurements are also necessary for developing air pollutants control strategies or for evaluating the effectiveness of these strategies, especially, for long periods. In this study an attempt is made in order to investigate the particle size distribution of fly ash and fugitive dust in a heavy industrialized (mining and power stations operations) area with complex terrain in the northwestern part of Greece. Parallel total suspended particulates (TSP) and particulate matter with an aerodynamic diameter less than 10 microm (PM10) concentrations are analyzed. These measurements gathered from thirteen monitoring stations located in the greater area of interest. Spatial, temporal variation and trend are analyzed over the last seven years. Furthermore, the geographical variation of PM10 - TSP correlation and PM10/TSP ratio are investigated and compared to those in the literature. The analysis has indicated that a complex system of sources and meteorological conditions modulate the particulate pollution of the examined area.

Assessment of elemental contamination in road dust using EDXRF

International Nuclear Information System (INIS)

Saradhi, I.V.; Sandeep, P.; Pandit, G.G.

2014-01-01

Road dust samples were collected in different locations of heavy traffic, medium traffic, express way and industrial areas of Mumbai. The concentrations of various elements (Mg, Al, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn and Pb) in road dust samples were analyzed using EDXRF. The average elemental profile of road dust in Mumbai was comparable with studies carried out in other countries with slight variations. The estimated geo accumulation indices and enrichment factors indicated moderate elemental contamination and enrichment of anthropogenic elements in road dust samples. Factor analysis of elemental data resolved four sources namely crustal, tyre wear, vehicular/industrial emissions and break wear. (author)

Dust extinction and X-ray emission from the starburst galaxy NGC 1482

Science.gov (United States)

Vagshette, N. D.; Pandge, M. B.; Pandey, S. K.; Patil, M. K.

2012-07-01

We present the results based on multiwavelength imaging observations of the prominent dust lane starburst galaxy NGC 1482 aimed to investigate the extinction properties of dust existing in the extreme environment. (B-V) colour-index map derived for the starburst galaxy NGC 1482 confirms two prominent dust lanes running along its optical major axis and are found to extend up to ˜11 kpc. In addition to the main lanes, several filamentary structures of dust originating from the central starburst are also evident. Though, the dust is surrounded by exotic environment, the average extinction curve derived for this target galaxy is compatible with the Galactic curve, with RV = 3.05, and imply that the dust grains responsible for the optical extinction in the target galaxy are not really different than the canonical grains in the Milky Way. Our estimate of total dust content of NGC 1482 assuming screening effect of dust is ˜2.7 × 105 M⊙, and provide lower limit due to the fact that our method is not sensitive to the intermix component of dust. Comparison of the observed dust in the galaxy with that supplied by the SNe to the ISM, imply that this supply is not sufficient to account for the observed dust and hence point towards the origin of dust in this galaxy through a merger like event. Our multiband imaging analysis reveals a qualitative physical correspondence between the morphologies of the dust and Hα emission lines as well as diffuse X-ray emission in this galaxy. Spatially resolved spectral analysis of the hot gas along outflows exhibit a gradient in the temperature. Similar gradient was also noticed in the measured values of metallicity, indicating that the gas in the halo is not yet enriched. High resolution, 2-8 keV Chandra image reveals a pair of point sources in the nuclear region with their luminosities equal to 2.27 × 1039 erg s-1 and 9.34 × 1039 erg s-1, and are in excess of the Eddington-limit of 1.5 M⊙ accreting source. Spectral analysis of these

Application of synchrotron microprobe methods to solid-phase speciation of metals and metalloids in house dust.

Science.gov (United States)

Walker, S R; Jamieson, H E; Rasmussen, P E

2011-10-01

Determination of the source and form of metals in house dust is important to those working to understand human and particularly childhood exposure to metals in residential environments. We report the development of a synchrotron microprobe technique for characterization of multiple metal hosts in house dust. We have applied X-ray fluorescence for chemical characterization and X-ray diffraction for crystal structure identification using microfocused synchrotron X-rays at a less than 10 μm spot size. The technique has been evaluated by application to archived house dust samples containing elevated concentrations of Pb, Zn, and Ba in bedroom dust, and Pb and As in living room dust. The technique was also applied to a sample of soil from the corresponding garden to identify linkages between indoor and outdoor sources of metals. Paint pigments including white lead (hydrocerussite) and lithopone (wurtzite and barite) are the primary source of Pb, Zn, and Ba in bedroom dust, probably related to renovation activity in the home at the time of sampling. The much lower Pb content in the living room dust shows a relationship to the exterior soil and no specific evidence of Pb and Zn from the bedroom paint pigments. The technique was also successful at confirming the presence of chromated copper arsenate treated wood as a source of As in the living room dust. The results of the study have confirmed the utility of this approach in identifying specific metal forms within the dust.

Constraining the Dust Opacity Law in Three Small and Isolated Molecular Clouds

Energy Technology Data Exchange (ETDEWEB)

Webb, K. A.; Thanjavur, K. [Department of Physics and Astronomy, 3800 Finnerty Road, University of Victoria, Victoria, BC, V8P 5C2 (Canada); Di Francesco, J. [National Research Council of Canada, Herzberg Institute of Astrophysics, 5071 West Saanich Road, Victoria, BC, V9E 2E7 (Canada); Sadavoy, S. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Launhardt, R.; Vicente, J. Abreu; Kainulainen, J. [Max-Planck-Institut für Astronomy, Königstuhl 17, D-69117, Heidelberg (Germany); Shirley, Y. [Steward Observatory, 933 North Cherry Avenue, Tucson, AZ 85721 (United States); Stutz, A., E-mail: kawebb@uvic.ca [Departmento de Astronomìa, Facultad Ciencias Físicas y Matemáticas, Universidad de Concepción, Av. Esteban Iturra s/n Barro Universitario, Casilla 160-C, Concepción (Chile)

2017-11-01

Density profiles of isolated cores derived from thermal dust continuum emission rely on models of dust properties, such as mass opacity, that are poorly constrained. With complementary measures from near-infrared extinction maps, we can assess the reliability of commonly used dust models. In this work, we compare Herschel -derived maps of the optical depth with equivalent maps derived from CFHT WIRCAM near-infrared observations for three isolated cores: CB 68, L 429, and L 1552. We assess the dust opacities provided from four models: OH1a, OH5a, Orm1, and Orm4. Although the consistency of the models differs between the three sources, the results suggest that the optical properties of dust in the envelopes of the cores are best described by either silicate and bare graphite grains (e.g., Orm1) or carbonaceous grains with some coagulation and either thin or no ice mantles (e.g., OH5a). None of the models, however, individually produced the most consistent optical depth maps for every source. The results suggest that either the dust in the cores is not well-described by any one dust property model, the application of the dust models cannot be extended beyond the very center of the cores, or more complex SED fitting functions are necessary.

Dust particle diffusion in ion beam transport region

Energy Technology Data Exchange (ETDEWEB)

Miyamoto, N.; Okajima, Y.; Romero, C. F.; Kuwata, Y.; Kasuya, T.; Wada, M., E-mail: mwada@mail.doshisha.ac.jp [Graduate school of Science and Engineering, Doshisha University, Kyotanabe, Kyoto 610-0321 (Japan)

2016-02-15

Dust particles of μm size produced by a monoplasmatron ion source are observed by a laser light scattering. The scattered light signal from an incident laser at 532 nm wavelength indicates when and where a particle passes through the ion beam transport region. As the result, dusts with the size more than 10 μm are found to be distributed in the center of the ion beam, while dusts with the size less than 10 μm size are distributed along the edge of the ion beam. Floating potential and electron temperature at beam transport region are measured by an electrostatic probe. This observation can be explained by a charge up model of the dust in the plasma boundary region.

40 CFR 63.7293 - What work practice standards must I meet for fugitive pushing emissions if I have a non-recovery...

Science.gov (United States)

2010-07-01

... meet for fugitive pushing emissions if I have a non-recovery coke oven battery? 63.7293 Section 63.7293... Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery Stacks Emission... pushing emissions if I have a non-recovery coke oven battery? (a) You must meet the requirements in...

The Paleozoic Dust Bowl: Dust Deposition in Tropical Western Pangaea (Midcontinent U.S.) at the Terminus of the Late Paleozoic Ice Age

Science.gov (United States)

Soreghan, G. S.; Heavens, N. G.; Benison, K. C.; Soreghan, M. J.; Mahowald, N. M.; Foster, T.; Zambito, J.; Sweet, A.; Kane, M.

2012-12-01

modeling possible causes and consequences of this massive dust record, which may include (1) partial glacial genesis in the CPM, (2) the action of the Pangaean mega-monsoon, and (3) particularly effective dust traps in the Midcontinent region. Modeling constrains the erosivity (the effect of winds and soil moisture effects) of a range of possible climate states on dust mobilization and underscores the relative difficulty of sourcing dust directly from the Appalachian-Ouachita orogenic system under most circumstances. Combining data and modeling helps constrain the erodibility (sediment availability, coherence, etc.) of dust sources. Reconstructions of marine dust deposition to the south and the west of the Anadarko basin suggest glacial-interglacial timescale erodibility changes were similar to those seen in the Midcontinent in the last 20,000 years, when it was at a much higher latitude.

Infrared astronomy and the galactic dust

International Nuclear Information System (INIS)

Pecker, J.C.

1977-01-01

The existence, in the Galaxy, of small absorbing dust grains has been known for a long time, as they redden the light of stars located behind them, and obscure by amounts which can often even be several magnitudes... In the infrared, where absorption is smaller, one can see through the dust, while at the same time, one can observe the emission of cold dust clouds. After a brief review of technical developments, the reasons for studying the infrared, and the principles of diagnostics, are given. The analysis of the spectral features leads to identification of ice, graphite, and various silicates, as main constituents of the dust. In the fifth section, examples are given of the various sources that one meets when travelling in the Galaxy: protostars, cold and dilute, dense envelopes of young stars (cold or hot), dilute envelopes of not so young stars, and ejected clouds surrounding evolved objects... The simultaneous observation of dust, molecules and atoms, in the same regions, shows that the knowledge of the circumstellar dense regions might be of a great interest, in the study of the origin of life, and of the evolution of the Universe. (Auth.)

Atmospheric Dust Modeling from Meso to Global Scales with the Online NMMB/BSC-Dust Model Part 2: Experimental Campaigns in Northern Africa

Science.gov (United States)

Haustein, K.; Perez, C.; Baldasano, J. M.; Jorba, O.; Basart, S.; Miller, R. L.; Janjic, Z.; Black, T.; Nickovic, S.; Todd, M. C.;

Highly Stretchable, Biocompatible, Striated Substrate Made from Fugitive Glue

Directory of Open Access Journals (Sweden)

Wei Li

2015-06-01

Full Text Available We developed a novel substrate made from fugitive glue (styrenic block copolymer that can be used to analyze the effects of large strains on biological samples. The substrate has the following attributes: (1 It is easy to make from inexpensive components; (2 It is transparent and can be used in optical microscopy; (3 It is extremely stretchable as it can be stretched up to 700% strain; (4 It can be micro-molded, for example we created micro-ridges that are 6 μm high and 13 μm wide; (5 It is adhesive to biological fibers (we tested fibrin fibers, and can be used to uniformly stretch those fibers; (6 It is non-toxic to cells (we tested human mammary epithelial cells; (7 It can tolerate various salt concentrations up to 5 M NaCl and low (pH 0 and high (pH 14 pH values. Stretching of this extraordinary stretchable substrate is relatively uniform and thus, can be used to test multiple cells or fibers in parallel under the same conditions.

3 MV hypervelocity dust accelerator at the Colorado Center for Lunar Dust and Atmospheric Studies.

Science.gov (United States)

Shu, Anthony; Collette, Andrew; Drake, Keith; Grün, Eberhard; Horányi, Mihály; Kempf, Sascha; Mocker, Anna; Munsat, Tobin; Northway, Paige; Srama, Ralf; Sternovsky, Zoltán; Thomas, Evan

2012-07-01

A hypervelocity dust accelerator for studying micrometeorite impacts has been constructed at the Colorado Center for Lunar Dust and Atmospheric Studies (CCLDAS) at the University of Colorado. Based on the Max-Planck-Institüt für Kernphysik (MPI-K) accelerator, this accelerator is capable of emitting single particles of a specific mass and velocity selected by the user. The accelerator consists of a 3 MV Pelletron generator with a dust source, four image charge pickup detectors, and two interchangeable target chambers: a large high-vacuum test bed and an ultra-high vacuum impact study chamber. The large test bed is a 1.2 m diameter, 1.5 m long cylindrical vacuum chamber capable of pressures as low as 10(-7) torr while the ultra-high vacuum chamber is a 0.75 m diameter, 1.1 m long chamber capable of pressures as low as 10(-10) torr. Using iron dust of up to 2 microns in diameter, final velocities have been measured up to 52 km/s. The spread of the dust particles and the effect of electrostatic focusing have been measured using a long exposure CCD and a quartz target. Furthermore, a new technique of particle selection is being developed using real time digital filtering techniques. Signals are digitized and then cross-correlated with a shaped filter, resulting in a suppressed noise floor. Improvements over the MPI-K design, which include a higher operating voltage and digital filtering for detection, increase the available parameter space of dust emitted by the accelerator. The CCLDAS dust facility is a user facility open to the scientific community to assist with instrument calibrations and experiments.

3 MV hypervelocity dust accelerator at the Colorado Center for Lunar Dust and Atmospheric Studies

Energy Technology Data Exchange (ETDEWEB)

Shu, Anthony; Horanyi, Mihaly; Kempf, Sascha; Thomas, Evan [Colorado Center for Lunar Dust and Atmospheric Studies, Boulder, Colorado 80303 (United States); Department of Physics, University of Colorado, Boulder, Colorado 80309 (United States); Laboratory for Atmospheric and Space Physics, 1234 Innovation Drive, Boulder, Colorado 80303 (United States); Collette, Andrew; Drake, Keith; Northway, Paige [Colorado Center for Lunar Dust and Atmospheric Studies, Boulder, Colorado 80303 (United States); Laboratory for Atmospheric and Space Physics, 1234 Innovation Drive, Boulder, Colorado 80303 (United States); Gruen, Eberhard [Colorado Center for Lunar Dust and Atmospheric Studies, Boulder, Colorado 80303 (United States); MPI fuer Kernphysik, Saupfercheckweg 1, D-69117 Heidelberg (Germany); Mocker, Anna [Colorado Center for Lunar Dust and Atmospheric Studies, Boulder, Colorado 80303 (United States); MPI fuer Kernphysik, Saupfercheckweg 1, D-69117 Heidelberg (Germany); IRS, Universitaet Stuttgart, Pfaffenwaldring 31, D-70569 Stuttgart (Germany); Munsat, Tobin [Colorado Center for Lunar Dust and Atmospheric Studies, Boulder, Colorado 80303 (United States); Department of Physics, University of Colorado, Boulder, Colorado 80309 (United States); Srama, Ralf [MPI fuer Kernphysik, Saupfercheckweg 1, D-69117 Heidelberg (Germany); IRS, Universitaet Stuttgart, Pfaffenwaldring 31, D-70569 Stuttgart (Germany); and others

2012-07-15

A hypervelocity dust accelerator for studying micrometeorite impacts has been constructed at the Colorado Center for Lunar Dust and Atmospheric Studies (CCLDAS) at the University of Colorado. Based on the Max-Planck-Instituet fuer Kernphysik (MPI-K) accelerator, this accelerator is capable of emitting single particles of a specific mass and velocity selected by the user. The accelerator consists of a 3 MV Pelletron generator with a dust source, four image charge pickup detectors, and two interchangeable target chambers: a large high-vacuum test bed and an ultra-high vacuum impact study chamber. The large test bed is a 1.2 m diameter, 1.5 m long cylindrical vacuum chamber capable of pressures as low as 10{sup -7} torr while the ultra-high vacuum chamber is a 0.75 m diameter, 1.1 m long chamber capable of pressures as low as 10{sup -10} torr. Using iron dust of up to 2 microns in diameter, final velocities have been measured up to 52 km/s. The spread of the dust particles and the effect of electrostatic focusing have been measured using a long exposure CCD and a quartz target. Furthermore, a new technique of particle selection is being developed using real time digital filtering techniques. Signals are digitized and then cross-correlated with a shaped filter, resulting in a suppressed noise floor. Improvements over the MPI-K design, which include a higher operating voltage and digital filtering for detection, increase the available parameter space of dust emitted by the accelerator. The CCLDAS dust facility is a user facility open to the scientific community to assist with instrument calibrations and experiments.

Trace-metal concentrations in African dust: effects of long-distance transport and implications for human health

Science.gov (United States)

Garrison, Virginia; Lamothe, Paul; Morman, Suzette; Plumlee, Geoffrey S.; Gilkes, Robert; Prakongkep, Nattaporn

2010-01-01

The Sahara and Sahel lose billions of tons of eroded mineral soils annually to the Americas and Caribbean, Europe and Asia via atmospheric transport. African dust was collected from a dust source region (Mali, West Africa) and from downwind sites in the Caribbean [Trinidad-Tobago (TT) and U.S. Virgin Islands (VI)] and analysed for 32 trace-elements. Elemental composition of African dust samples was similar to that of average upper continental crust (UCC), with some enrichment or depletion of specific trace-elements. Pb enrichment was observed only in dust and dry deposition samples from the source region and was most likely from local use of leaded gasoline. Dust particles transported long-distances (VI and TT) exhibited increased enrichment of Mo and minor depletion of other elements relative to source region samples. This suggests that processes occurring during long-distance transport of dust produce enrichment/depletion of specific elements. Bioaccessibility of trace-metals in samples was tested in simulated human fluids (gastric and lung) and was found to be greater in downwind than source region samples, for some metals (e.g., As). The large surface to volume ratio of the dust particles (<2.5 µm) at downwind sites may be a factor.

Hypervelocity Dust Impacts in Space and the Laboratory

Science.gov (United States)

Horanyi, Mihaly; Colorado CenterLunar Dust; Atmospheric Studies (CCLDAS) Team

2013-10-01

Interplanetary dust particles continually bombard all objects in the solar system, leading to the excavation of material from the target surfaces, the production of secondary ejecta particles, plasma, neutral gas, and electromagnetic radiation. These processes are of interest to basic plasma science, planetary and space physics, and engineering to protect humans and instruments against impact damages. The Colorado Center for Lunar Dust and Atmospheric Studies (CCLDAS) has recently completed a 3 MV dust accelerator, and this talk will summarize our initial science results. The 3 MV Pelletron contains a dust source, feeding positively charged micron and sub-micron sized particles into the accelerator. We will present the technical details of the facility and its capabilities, as well as the results of our initial experiments for damage assessment of optical devices, and penetration studies of thin films. We will also report on the completion of our dust impact detector, the Lunar Dust Experiment (LDEX), is expected to be flying onboard the Lunar Atmosphere and Dust Environment Explorer (LADEE) mission by the time of this presentation. LDEX was tested, and calibrated at our dust accelerator. We will close by offering the opportunity to use this facility by the planetary, space and plasma physics communities.

Characteristics and transport of organochlorine pesticides in urban environment: air, dust, rain, canopy throughfall, and runoff.

Science.gov (United States)

Zhang, Wei; Ye, Youbin; Hu, Dan; Ou, Langbo; Wang, Xuejun

2010-11-01

Characteristics and transport of organochlorine pesticides (OCPs) in urban multiple environments, including air, dust, rain, canopy throughfall, and runoff water, are explored in this study. Hexachlorocyclohexanes (HCHs) dominated in both air and rain water, and dichlorodiphenyltrichloroethane (DDT) related substances showed a higher affinity to dust. Relatively high concentrations of DDT and dichlorodiphenyldichloroethylene (DDE) in air, rain and dust imply that technical DDT in the environment has been degrading, and there may be unknown local or regional emission sources that contain DDTs in the study area. Source identification showed that DDTs in Beijing urban environments with a fresh signature may originate from the atmospheric transport from remote areas. The ratio of α-/γ-HCH in dust, rain, canopy throughfall and runoff were close to 1, indicating the possible use of lindane. OCPs in runoff were transported from various sources including rain, dust, and canopy throughfall. In runoff, DDTs and hexachlorobenzene (HCB) were mainly transported from dust, and HCHs were mainly from rain and canopy throughfall.

Product screening for sources of halogenated flame retardants in Canadian house and office dust

Energy Technology Data Exchange (ETDEWEB)

Abbasi, Golnoush [Department of Geography, University of Toronto, 100 St. George St., Toronto M5S 3G3 (Canada); Saini, Amandeep [Department of Physical and Environmental Sciences, University of Toronto, 1265 Military Trail, Toronto M1C 1A4 (Canada); Goosey, Emma [Department of Earth Sciences, University of Toronto, 22 Russell Street, Toronto M5S 3B1 (Canada); Diamond, Miriam L., E-mail: miriam.diamond@utoronto.ca [Department of Earth Sciences, University of Toronto, 22 Russell Street, Toronto M5S 3B1 (Canada); Department of Physical and Environmental Sciences, University of Toronto, 1265 Military Trail, Toronto M1C 1A4 (Canada)

2016-03-01

Human exposure to halogenated flame retardants (HFRs) such as polybrominated diphenyl ethers (PBDEs) and their replacements, can be related to exposure to indoor dust and direct contact with HFR-containing products. This study aimed to identify electronic products that contributed to HFRs measured in indoor dust and to develop a screening method for identifying HFRs in hard polymer products. Concentrations of 10 PBDEs and 12 halogenated replacements in dust and surface wipe samples of hard polymer casings of electronic products plus Br in the surfaces of those casing measured using X-ray fluorescence (XRF) were analyzed from 35 homes and 10 offices in Toronto (ON, Canada). HFR concentrations in dust and product wipes were positively correlated. Thus, we hypothesize that electronic products with the highest HFR concentrations contribute the most to concentrations in dust, regardless of the volatility of the HFR. Abundant HFRs in dust and product wipes were PBDEs (BDE-47, 99, 100, 153, 154, 183, 209), TDCPP, DBDPE, EH-TBB and BEHTBP. Older CRT TVs had the highest concentration of BDE-209 of all products tested. This was followed by higher concentrations of HFRs in PCs, Audio/Video (A/V) devices, small household appliances (HHAs) and flat screen TVs. The removal of HFRs from polymer surfaces using wipes supports concerns that HFRs could be transferred from these surfaces to hands as a result of direct contact with HFR-containing products. Surface wipe testing shows promise for screening additive HFRs. In comparison, the Br-content obtained using a handheld XRF analyzer did not correspond to concentrations obtained from surface wipe testing. - Highlights: • Concentrations of flame retardants in dust correlated with product surface wipes • Most abundant FRs in electronics were PBDEs, TDCPP, DBDPE, EH-TBB and BEHTBP. • Descending order of FRs in CRTs, TVs, PCs, A-V devices, and small household appliances • Product wipe testing, but not XRF, useful for non

Product screening for sources of halogenated flame retardants in Canadian house and office dust

International Nuclear Information System (INIS)

Abbasi, Golnoush; Saini, Amandeep; Goosey, Emma; Diamond, Miriam L.

2016-01-01

Human exposure to halogenated flame retardants (HFRs) such as polybrominated diphenyl ethers (PBDEs) and their replacements, can be related to exposure to indoor dust and direct contact with HFR-containing products. This study aimed to identify electronic products that contributed to HFRs measured in indoor dust and to develop a screening method for identifying HFRs in hard polymer products. Concentrations of 10 PBDEs and 12 halogenated replacements in dust and surface wipe samples of hard polymer casings of electronic products plus Br in the surfaces of those casing measured using X-ray fluorescence (XRF) were analyzed from 35 homes and 10 offices in Toronto (ON, Canada). HFR concentrations in dust and product wipes were positively correlated. Thus, we hypothesize that electronic products with the highest HFR concentrations contribute the most to concentrations in dust, regardless of the volatility of the HFR. Abundant HFRs in dust and product wipes were PBDEs (BDE-47, 99, 100, 153, 154, 183, 209), TDCPP, DBDPE, EH-TBB and BEHTBP. Older CRT TVs had the highest concentration of BDE-209 of all products tested. This was followed by higher concentrations of HFRs in PCs, Audio/Video (A/V) devices, small household appliances (HHAs) and flat screen TVs. The removal of HFRs from polymer surfaces using wipes supports concerns that HFRs could be transferred from these surfaces to hands as a result of direct contact with HFR-containing products. Surface wipe testing shows promise for screening additive HFRs. In comparison, the Br-content obtained using a handheld XRF analyzer did not correspond to concentrations obtained from surface wipe testing. - Highlights: • Concentrations of flame retardants in dust correlated with product surface wipes • Most abundant FRs in electronics were PBDEs, TDCPP, DBDPE, EH-TBB and BEHTBP. • Descending order of FRs in CRTs, TVs, PCs, A-V devices, and small household appliances • Product wipe testing, but not XRF, useful for non

Heavy Metals Speciation in Dust Samples from Various Parts of ...

African Journals Online (AJOL)

Dust on our roads constitutes a major source of environmental hazard. Little attention is paid to the enormous challenges resulting from its polluting effect and health implications. In this investigation, twenty five dust samples were collected from 5 locations within Ebonyi North, South and Central Senatorial Zones between ...

Synergistic Use of Remote Sensing and Modeling for Tracing Dust Storms in the Mediterranean

Directory of Open Access Journals (Sweden)

D. G. Kaskaoutis

2012-01-01

Full Text Available This study focuses on the detection of the dust source region and monitoring of the transport of the dust plume from its primary outflow to final deposition. The application area is the Sahara desert and the eastern Mediterranean, where two dust events occurred during the period 4–6 February 2009, an unusual event for a winter period. The Aqua-MODIS and OMI observations clearly define the spatial distribution of the dust plumes, while the CALIPSO observations of total attenuated backscatter (TAB at 532 nm, depolarization ratio (DR, and attenuated color ratio (1064/532 nm on 5 February 2009 provide a clear view and vertical structure of the dust-laden layer. The dust source region is defined to be near the Chad-Niger-Libyan borders, using satellite observations and model (DREAM output. This dust plume is vertically extended up to 2.5 km and is observed as a mass plume of dust from surface level to that altitude, where the vertical variation of TAB (0.002 to 0.2 and DR (0.2–0.5 implies dust-laden layer with non-spherical particles. CALIPSO profiles show that after the dust plume reached at its highest level, the dust particles start to be deposited over the Mediterranean and the initial dust plume was strongly attenuated, while features of dust were limited below about 1–1.5 km for latitudes northern of ~36° (Greek territory.

The representation of dust transport and missing urban sources as major issues for the simulation of PM episodes in a Mediterranean area

Directory of Open Access Journals (Sweden)

E. Flaounas

2009-10-01

Full Text Available Due to its adverse effects on human health, atmospheric particulate matter (PM constitutes a growing challenge for air quality management. It is also a complex subject of study. The understanding of its atmospheric evolution is indeed made difficult by the wide number of sources and the numerous processes that govern its evolution in the troposphere. As a consequence, the representation of particulate matter in chemistry-transport models needs to be permanently evaluated and enhanced in order to refine our comprehension of PM pollution events and to propose consistent environmental policies. The study presented here focuses on two successive summer particulate pollution episodes that occurred on the French Mediterranean coast. We identify and analyze the constitutive elements of the first and more massive episode and we discuss their representation within a eulerian model.

The results show that the model fails in reproducing the variability and the amplitude of dust import from western Africa, and that it constitutes a strong bias in PM daily forecasts. We then focus on the lack of diurnal variability in the model, which is attributed to missing urban sources in standard emission inventories, and notably the resuspension of particles by urban road traffic. Through a sensitivity study based on PM and NO_x measurements, we assess the sensitivity of PM to local emissions and the need to reconsider road traffic PM sources. In parallel, by coupling the CHIMERE-DUST model outputs to our simulation, we show that the representation of transcontinental dust transport allows a much better representation of atmospheric particles in southern France, and that it is needed in the frame of air quality management for the quantification of the anthropogenic part of particulate matter pollution.

Diagnostic evaluation of the Community Earth System Model in simulating mineral dust emission with insight into large-scale dust storm mobilization in the Middle East and North Africa (MENA)

Science.gov (United States)

Parajuli, Sagar Prasad; Yang, Zong-Liang; Lawrence, David M.

2016-06-01

Large amounts of mineral dust are injected into the atmosphere during dust storms, which are common in the Middle East and North Africa (MENA) where most of the global dust hotspots are located. In this work, we present simulations of dust emission using the Community Earth System Model Version 1.2.2 (CESM 1.2.2) and evaluate how well it captures the spatio-temporal characteristics of dust emission in the MENA region with a focus on large-scale dust storm mobilization. We explicitly focus our analysis on the model's two major input parameters that affect the vertical mass flux of dust-surface winds and the soil erodibility factor. We analyze dust emissions in simulations with both prognostic CESM winds and with CESM winds that are nudged towards ERA-Interim reanalysis values. Simulations with three existing erodibility maps and a new observation-based erodibility map are also conducted. We compare the simulated results with MODIS satellite data, MACC reanalysis data, AERONET station data, and CALIPSO 3-d aerosol profile data. The dust emission simulated by CESM, when driven by nudged reanalysis winds, compares reasonably well with observations on daily to monthly time scales despite CESM being a global General Circulation Model. However, considerable bias exists around known high dust source locations in northwest/northeast Africa and over the Arabian Peninsula where recurring large-scale dust storms are common. The new observation-based erodibility map, which can represent anthropogenic dust sources that are not directly represented by existing erodibility maps, shows improved performance in terms of the simulated dust optical depth (DOD) and aerosol optical depth (AOD) compared to existing erodibility maps although the performance of different erodibility maps varies by region.

Submillimeter Observations of CLASH 2882 and the Evolution of Dust in this Galaxy

Science.gov (United States)

Dwek, Eli; Staguhn, Johannes; Arendt, Richard G; Kovacs, Attila; Decarli, Roberto; Egami, Eiichi; Michalowski, Michal J.; Rawle, Timothy D.; Toft, Sune; Walter, Fabian

2015-01-01

Two millimeter observations of the MACS J1149.6+2223 cluster have detected a source that was consistent with the location of the lensed MACS 1149-JD galaxy at z = 9.6. A positive identification would have rendered this galaxy as the youngest dust forming galaxy in the universe. Follow up observation with the AzTEC 1.1 mm camera and the IRAM NOrthern Extended Millimeter Array (NOEMA) at 1.3 mm have not confirmed this association. In this paper we show that the NOEMA observations associate the 2 mm source with [PCB2012] 2882,12 source number 2882 in the Cluster Lensing And Supernova survey with Hubble (CLASH) catalog of MACS J1149.6 +2223. This source, hereafter referred to as CLASH 2882, is a gravitationally lensed spiral galaxy at z = 0.99. We combine the Goddard IRAM Superconducting 2-Millimeter Observer (GISMO) 2 mm and NOEMA 1.3 mm fluxes with other (rest frame) UV to far-IR observations to construct the full spectral energy distribution of this galaxy, and derive its star formation history, and stellar and interstellar dust content. The current star formation rate of the galaxy is 54/mu/Solar Mass/yr, and its dust mass is about 5 × 10(exp 7)/mu Solar Mass, where mu is the lensing magnification factor for this source, which has a mean value of 2.7. The inferred dust mass is higher than the maximum dust mass that can be produced by core collapse supernovae and evolved AGB stars. As with many other star forming galaxies, most of the dust mass in CLASH 2882 must have been accreted in the dense phases of the interstellar medium.

Atmospheric dust modeling from meso to global scales with the online NMMB/BSC-Dust model – Part 2: Experimental campaigns in Northern Africa

Directory of Open Access Journals (Sweden)

K. Haustein

2012-03-01

Full Text Available The new NMMB/BSC-Dust model is intended to provide short to medium-range weather and dust forecasts from regional to global scales. It is an online model in which the dust aerosol dynamics and physics are solved at each model time step. The companion paper (Pérez et al., 2011 develops the dust model parameterizations and provides daily to annual evaluations of the model for its global and regional configurations. Modeled aerosol optical depth (AOD was evaluated against AERONET Sun photometers over Northern Africa, Middle East and Europe with correlations around 0.6–0.7 on average without dust data assimilation. In this paper we analyze in detail the behavior of the model using data from the Saharan Mineral dUst experiment (SAMUM-1 in 2006 and the Bodélé Dust Experiment (BoDEx in 2005. AOD from satellites and Sun photometers, vertically resolved extinction coefficients from lidars and particle size distributions at the ground and in the troposphere are used, complemented by wind profile data and surface meteorological measurements. All simulations were performed at the regional scale for the Northern African domain at the expected operational horizontal resolution of 25 km. Model results for SAMUM-1 generally show good agreement with satellite data over the most active Saharan dust sources. The model reproduces the AOD from Sun photometers close to sources and after long-range transport, and the dust size spectra at different height levels. At this resolution, the model is not able to reproduce a large haboob that occurred during the campaign. Some deficiencies are found concerning the vertical dust distribution related to the representation of the mixing height in the atmospheric part of the model. For the BoDEx episode, we found the diurnal temperature cycle to be strongly dependant on the soil moisture, which is underestimated in the NCEP analysis used for model initialization. The low level jet (LLJ and the dust AOD over the Bodélé are

DustEM: Dust extinction and emission modelling

Science.gov (United States)

Compiègne, M.; Verstraete, L.; Jones, A.; Bernard, J.-P.; Boulanger, F.; Flagey, N.; Le Bourlot, J.; Paradis, D.; Ysard, N.

2013-07-01

DustEM computes the extinction and the emission of interstellar dust grains heated by photons. It is written in Fortran 95 and is jointly developed by IAS and CESR. The dust emission is calculated in the optically thin limit (no radiative transfer) and the default spectral range is 40 to 108 nm. The code is designed so dust properties can easily be changed and mixed and to allow for the inclusion of new grain physics.

Trace Metals and Mineral Composition of Harmattan Dust Haze in ...

African Journals Online (AJOL)

ADOWIE PERE

2018-01-29

Jan 29, 2018 ... ABSTRACT: Trace metals and mineralogical composition of harmattan dust haze was carried out on samples collected at Ilorin (80 32'N, ... Sahara desert which transports the dust by wind. Junge (1979) reported that on the .... Schwela et al 2002, it was observed that road transport emission sources ...

Determination of combustible volatile matter in coal mine roadway dusts by backscatter of x-rays from a radioisotope source

International Nuclear Information System (INIS)

Ailwood, C.R.; Bunch, K.; Fookes, R.A.; Gravitis, V.L.; Watt, J.S.

1977-01-01

The combustible volatile matter in coal mine roadway dusts (CVM) has been determined using x-ray backscatter techniques. The correlation between x-ray and chemical techniques is reasonably good for the 92 samples from collieries on the Bulli seam, and the maximum error expected at the maximum level of 11.5 weight per cent CVM permitted in the N.S.W. Coal Mines Regulation Act, 1912, as amended, is about +- 2.5 weight per cent. This x-ray technique can be used only when the combustible volatile content of the coal matter (CVM) varies within a limited range, and a separate calibration is required for each coal seam. Portable equipment based on a radioisotope x-ray source and digital ratemeter makes possible simple and rapid analysis, and with adaptation to use in coal mines should lead to much more comprehensive testing of roadways and hence improved overall prevention of coal dust explosions. (author)

Geologic and anthropogenic sources of contamination in settled dust of a historic mining port city in northern Chile: health risk implications

Directory of Open Access Journals (Sweden)

Joseline S. Tapia

2018-04-01

Full Text Available Chile is the leading producer of copper worldwide and its richest mineral deposits are found in the Antofagasta Region of northern Chile. Mining activities have significantly increased income and employment in the region; however, there has been little assessment of the resulting environmental impacts to residents. The port of Antofagasta, located 1,430 km north of Santiago, the capital of Chile, functioned as mineral stockpile until 1998 and has served as a copper concentrate stockpile since 2014. Samples were collected in 2014 and 2016 that show elevated concentrations of As, Cu, Pb, and Zn in street dust and in residents’ blood (Pb and urine (As samples. To interpret and analyze the spatial variability and likely sources of contamination, existent data of basement rocks and soil geochemistry in the city as well as public-domain airborne dust were studied. Additionally, a bioaccessibility assay of airborne dust was conducted and the chemical daily intake and hazard index were calculated to provide a preliminary health risk assessment in the vicinity of the port. The main conclusions indicate that the concentrations of Ba, Co, Cr, Mn, Ni, and V recorded from Antofagasta dust likely originate from intrusive, volcanic, metamorphic rocks, dikes, or soil within the city. However, the elevated concentrations of As, Cd, Cu, Mo, Pb, and Zn do not originate from these geologic outcrops, and are thus considered anthropogenic contaminants. The average concentrations of As, Cu, and Zn are possibly the highest in recorded street dust worldwide at 239, 10,821, and 11,869 mg kg−1, respectively. Furthermore, the contaminants As, Pb, and Cu exhibit the highest bioaccessibilities and preliminary health risk indices show that As and Cu contribute to elevated health risks in exposed children and adults chronically exposed to dust in Antofagasta, whereas Pb is considered harmful at any concentration. Therefore, an increased environmental awareness and greater

Geologic and anthropogenic sources of contamination in settled dust of a historic mining port city in northern Chile: health risk implications.

Science.gov (United States)

Tapia, Joseline S; Valdés, Jorge; Orrego, Rodrigo; Tchernitchin, Andrei; Dorador, Cristina; Bolados, Aliro; Harrod, Chris

2018-01-01

Chile is the leading producer of copper worldwide and its richest mineral deposits are found in the Antofagasta Region of northern Chile. Mining activities have significantly increased income and employment in the region; however, there has been little assessment of the resulting environmental impacts to residents. The port of Antofagasta, located 1,430 km north of Santiago, the capital of Chile, functioned as mineral stockpile until 1998 and has served as a copper concentrate stockpile since 2014. Samples were collected in 2014 and 2016 that show elevated concentrations of As, Cu, Pb, and Zn in street dust and in residents' blood (Pb) and urine (As) samples. To interpret and analyze the spatial variability and likely sources of contamination, existent data of basement rocks and soil geochemistry in the city as well as public-domain airborne dust were studied. Additionally, a bioaccessibility assay of airborne dust was conducted and the chemical daily intake and hazard index were calculated to provide a preliminary health risk assessment in the vicinity of the port. The main conclusions indicate that the concentrations of Ba, Co, Cr, Mn, Ni, and V recorded from Antofagasta dust likely originate from intrusive, volcanic, metamorphic rocks, dikes, or soil within the city. However, the elevated concentrations of As, Cd, Cu, Mo, Pb, and Zn do not originate from these geologic outcrops, and are thus considered anthropogenic contaminants. The average concentrations of As, Cu, and Zn are possibly the highest in recorded street dust worldwide at 239, 10,821, and 11,869 mg kg -1 , respectively. Furthermore, the contaminants As, Pb, and Cu exhibit the highest bioaccessibilities and preliminary health risk indices show that As and Cu contribute to elevated health risks in exposed children and adults chronically exposed to dust in Antofagasta, whereas Pb is considered harmful at any concentration. Therefore, an increased environmental awareness and greater protective measures

Dust in the Quasar Wind (Artist Concept)

Science.gov (United States)

2007-01-01

Dusty grains -- including tiny specks of the minerals found in the gemstones peridot, sapphires and rubies -- can be seen blowing in the winds of a quasar, or active black hole, in this artist's concept. The quasar is at the center of a distant galaxy. Astronomers using NASA's Spitzer Space Telescope found evidence that such quasar winds might have forged these dusty particles in the very early universe. The findings are another clue in an ongoing cosmic mystery: where did all the dust in our young universe come from? Dust is crucial for efficient star formation as it allows the giant clouds where stars are born to cool quickly and collapse into new stars. Once a star has formed, dust is also needed to make planets and living creatures. Dust has been seen as far back as when the universe was less than a tenth of its current age, but how did it get there? Most dust in our current epoch forms in the winds of evolved stars that did not exist when the universe was young. Theorists had predicted that winds from quasars growing in the centers of distant galaxies might be a source of this dust. While the environment close to a quasar is too hot for large molecules like dust grains to survive, dust has been found in the cooler, outer regions. Astronomers now have evidence that dust is created in these outer winds. Using Spitzer's infrared spectrograph instrument, scientists found a wealth of dust grains in a quasar called PG2112+059 located at the center of a galaxy 8 billion light-years away. The grains - including corundum (sapphires and rubies); forsterite (peridot); and periclase (naturally occurring in marble) - are not typically found in galaxies without quasars, suggesting they might have been freshly formed in the quasar's winds.

Improved dust representation in the Community Atmosphere Model

Science.gov (United States)

Albani, S.; Mahowald, N. M.; Perry, A. T.; Scanza, R. A.; Zender, C. S.; Heavens, N. G.; Maggi, V.; Kok, J. F.; Otto-Bliesner, B. L.

2014-09-01

Aerosol-climate interactions constitute one of the major sources of uncertainty in assessing changes in aerosol forcing in the anthropocene as well as understanding glacial-interglacial cycles. Here we focus on improving the representation of mineral dust in the Community Atmosphere Model and assessing the impacts of the improvements in terms of direct effects on the radiative balance of the atmosphere. We simulated the dust cycle using different parameterization sets for dust emission, size distribution, and optical properties. Comparing the results of these simulations with observations of concentration, deposition, and aerosol optical depth allows us to refine the representation of the dust cycle and its climate impacts. We propose a tuning method for dust parameterizations to allow the dust module to work across the wide variety of parameter settings which can be used within the Community Atmosphere Model. Our results include a better representation of the dust cycle, most notably for the improved size distribution. The estimated net top of atmosphere direct dust radiative forcing is -0.23 ± 0.14 W/m2 for present day and -0.32 ± 0.20 W/m2 at the Last Glacial Maximum. From our study and sensitivity tests, we also derive some general relevant findings, supporting the concept that the magnitude of the modeled dust cycle is sensitive to the observational data sets and size distribution chosen to constrain the model as well as the meteorological forcing data, even within the same modeling framework, and that the direct radiative forcing of dust is strongly sensitive to the optical properties and size distribution used.

Contribution of Asian dust to atmospheric deposition of radioactive cesium (137Cs)

International Nuclear Information System (INIS)

Fukuyama, Taijiro; Fujiwara, Hideshi

2008-01-01

Both Asian dust (kosa) transported from the East Asian continent and locally suspended dust near monitoring sites contribute to the observed atmospheric deposition of 137 Cs in Japan. To estimate the relative contribution of these dust phenomena to the total 137 Cs deposition, we monitored weekly deposition of mineral particles and 137 Cs in spring. Deposition of 137 Cs from a single Asian dust event was 62.3 mBq m -2 and accounted for 67% of the total 137 Cs deposition during the entire monitoring period. Furthermore, we found high 137 Cs specific activity in the Asian dust deposition sample. Although local dust events contributed to 137 Cs deposition, their contribution was considerably smaller than that of Asian dust. We conclude that the primary source of atmospheric 137 Cs in Japan is dust transported from the East Asian continent

PM10 concentration levels at an urban and background site in Cyprus: the impact of urban sources and dust storms.

Science.gov (United States)

Achilleos, Souzana; Evans, John S; Yiallouros, Panayiotis K; Kleanthous, Savvas; Schwartz, Joel; Koutrakis, Petros

2014-12-01

Air quality in Cyprus is influenced by both local and transported pollution, including desert dust storms. We examined PM10 concentration data collected in Nicosia (urban representative) from April 1, 1993, through December 11, 2008, and in Ayia Marina (rural background representative) from January 1, 1999, through December 31, 2008. Measurements were conducted using a Tapered Element Oscillating Micro-balance (TEOM). PM10 concentrations, meteorological records, and satellite data were used to identify dust storm days. We investigated long-term trends using a Generalized Additive Model (GAM) after controlling for day of week, month, temperature, wind speed, and relative humidity. In Nicosia, annual PM10 concentrations ranged from 50.4 to 63.8 μg/m3 and exceeded the EU annual standard limit enacted in 2005 of 40 μg/m3 every year A large, statistically significant impact of urban sources (defined as the difference between urban and background levels) was seen in Nicosia over the period 2000-2008, and was highest during traffic hours, weekdays, cold months, and low wind conditions. Our estimate of the mean (standard error) contribution of urban sources to the daily ambient PM10 was 24.0 (0.4) μg/m3. The study of yearly trends showed that PM10 levels in Nicosia decreased from 59.4 μg/m3 in 1993 to 49.0 μg/m3 in 2008, probably in part as a result of traffic emission control policies in Cyprus. In Ayia Marina, annual concentrations ranged from 27.3 to 35.6 μg/m3, and no obvious time trends were observed. The levels measured at the Cyprus background site are comparable to background concentrations reported in other Eastern Mediterranean countries. Average daily PM10 concentrations during desert dust storms were around 100 μg/m3 since 2000 and much higher in earlier years. Despite the large impact ofdust storms and their increasing frequency over time, dust storms were responsible for a small fraction of the exceedances of the daily PM10 limit. Implications: This

Investigations of Wind/WAVES Dust Impacts

Science.gov (United States)

St Cyr, O. C.; Wilson, L. B., III; Rockcliffe, K.; Mills, A.; Nieves-Chinchilla, T.; Adrian, M. L.; Malaspina, D.

2017-12-01

The Wind spacecraft launched in November 1994 with a primary goal to observe and understand the interaction between the solar wind and Earth's magnetosphere. The waveform capture detector, TDS, of the radio and plasma wave investigation, WAVES [Bougeret et al., 1995], onboard Wind incidentally detected micron-sized dust as electric field pulses from the recollection of the impact plasma clouds (an unintended objective). TDS has detected over 100,000 dust impacts spanning almost two solar cycles; a dataset of these impacts has been created and was described in Malaspina & Wilson [2016]. The spacecraft continues to collect data about plasma, energetic particles, and interplanetary dust impacts. Here we report on two investigations recently conducted on the Wind/WAVES TDS database of dust impacts. One possible source of dust particles is the annually-recurring meteor showers. Using the nine major showers defined by the American Meteor Society, we compared dust count rates before, during, and after the peak of the showers using averaging windows of varying duration. However, we found no statistically significant change in the dust count rates due to major meteor showers. This appears to be an expected result since smaller grains, like the micron particles that Wind is sensitive to, are affected by electromagnetic interactions and Poynting-Robertson drag, and so are scattered away from their initial orbits. Larger grains tend to be more gravitationally dominated and stay on the initial trajectory of the parent body so that only the largest dust grains (those that create streaks as they burn up in the atmosphere) are left in the orbit of the parent body. Ragot and Kahler [2003] predicted that coronal mass ejections (CMEs) near the Sun could effectively scatter dust grains of comparable size to those observed by Wind. Thus, we examined the dust count rates immediately before, during, and after the passage of the 350 interplanetary CMEs observed by Wind over its 20+ year

Energetics study of West African dust haze

International Nuclear Information System (INIS)

Omotosho, J.B.

1988-10-01

The causes of the large and often persistent negative anomalies of equivalent potential temperature observed in the 900-700 hpa layer and which occurs in association with dust haze outbreaks over Kano in winter is investigated. Energetics results indicate that the primary mechanism for such anomalies is the horizontal transport of drier and, to a lesser extent, colder air at the upper levels by eddy motions, with consequent destabilization of the atmospheric boundary layer over the station. This is suggested as the mobilization mechanism responsible for raising dust from the surface over the Bilma/Faya-Largeau source region much further poleward. Temperature inversions were also found to be more pronounced during dust spells than in clear periods. (author). 18 refs, 6 figs, 2 tabs

Electromagnetically Interacting Dust Streams During Ulysses' Second Jupiter Encounter

International Nuclear Information System (INIS)

Krueger, H.; Forsyth, R.J.; Graps, A.L.; Gruen, E.

2005-01-01

The Jupiter system is a source of collimated burst-like streams of electrically charged 10-nm dust particles. In 2004 the Ulysses spacecraft had its second flyby at Jupiter and from late 2002 to early 2005 it measured a total of 24 dust streams between 0.8 and 3.4 AU from the planet. The grains show strong coupling to the interplanetary magnetic field: their impact directions correlate with the orientation and strength of the interplanetary magnetic field vector (namely its tangential and radial components) and they occur at 26 day intervals, closely matching the solar rotation period. Ulysses measured the dust streams over a large range in jovian latitude (+75 deg. to -35 deg.). Enhanced dust emission was measured along the jovian equator

Dust Deposition Events on Mt. Elbrus, Caucasus Mountains in the 21st Century Reconstructed from the Shallow Firn and Ice Cores (Invited)

Science.gov (United States)

Shahgedanova, M.; Kutuzov, S.; Mikhalenko, V.; Ginot, P.; Lavrentiev, I.

2013-12-01

This paper presents and discusses a record of dust deposition events reconstructed from the shallow firn and ice cores extracted on the Western Plateau, Mt. Elbrus, Caucasus Mountains, Russia. A combination of SEVIRI imagery, HYSPLIT trajectory model, meteorological and atmospheric optical depth data were used to establish timing of deposition events and source regions of dust with very high temporal (hours) and spatial (c. 50-100 km) resolution. The source regions of the desert dust transported to Mt. Elbrus were primarily located in the Middle East, in particular in eastern Syria and in the Syrian Desert at the border between Saudi Arabia, Iraq and Jordan. Northern Sahara, the foothills of the Djebel Akhdar Mountains in eastern Libya and the border region between Libya and Algeria were other important sources of desert dust. Dust sources in the Sahara were natural (e.g. palaeolakes and alluvial deposits in the foothills) while in the Middle East, dust entrainment occurred from both natural (e.g. dry river beds) and anthropogenic (e.g. agricultural fields) sources. The overall majority of dust deposition events occurred between March and June and, less frequently, dust deposition events occurred in February and October. In all cases, dust deposition was associated with depressions causing strong surface wind and dust uplift in the source areas, transportation of dust to the Caucasus with a strong south-westerly flow from the Sahara or southerly flow from the Middle East, merging of the dust clouds with precipitation-bearing weather fronts and precipitation over the Caucasus region. The Saharan depressions were vigorous and associated with stronger daily wind speeds of 20-30 m/s at the 700 hPa level; depressions forming over the Middle East and the associated wind speeds were weaker at 12-15 m/s. The Saharan depressions were less frequent than those carrying dust from the Middle East but higher dust loads were associated with the Saharan depressions. A higher

Ecological Restoration Programs Induced Amelioration of the Dust Pollution in North China Plain

Science.gov (United States)

Long, X.; Tie, X.; Li, G.; Junji, C.

2017-12-01

With Moderate Resolution Imaging Spectroradiometer (MODIS) land cover product (MCD12Q1), we quantitatively evaluate the ecological restoration programs (ERP) induced land cover change in China by calculating gridded the land use fraction (LUF). We clearly capture two obvious vegetation (grass and forest) protective barriers arise between the dust source region DSR and North China Plain NCP from 2011 to 2013. The WRF-DUST model is applied to investigate the impact of ERPs on dust pollution from 2 to 8 March 2016, corresponding to a national dust storm event over China. Despite some model biases, the WRF-DUST model reasonably reproduced the temporal variations of dust storm event, involving IOA of 0.96 and NMB of 2% for DSR, with IOA of 0.83 and NMB of -15% for downwind area of NCP. Generally, the WRF-DUST model well capture the spatial variations and evolutions of dust storm events with episode-average [PMC] correlation coefficient (R) of 0.77, especially the dust storm outbreak and transport evolution, involving daily average [PMC] R of 0.9 and 0.73 on 4-5 March, respectively. It is found that the ERPs generally reduce the dust pollution in NCP, especially for BTH, involving upper dust pollution control benefits of -15.3% (-21.0 μg m-3) for BTH, and -6.2% (-9.3 μg m-3) for NCP. We are the first to conduct model sensitivity studies to quantitatively evaluate the impacts of the ERPs on the dust pollution in NCP. And our narrative is independently based on first-hand sources, whereas government statistics.

Lemaître-Tolman-Bondi dust solutions in f (R) gravity

Science.gov (United States)

Sussman, Roberto A.; Jaime, Luisa G.

2017-12-01

We derive a class of non-static inhomogeneous dust solutions in f(R) gravity described by the Lemaître-Tolman-Bondi (LTB) metric. The field equations are fully integrated for all parameter subcases and compared with analogous subcases of LTB dust solutions of GR. Since the solutions do not admit regular symmetry centres, we have two possibilities: (i) a spherical dust cloud with angle deficit acting as the source of a vacuum Schwarzschild-like solution associated with a global monopole, or (ii) fully regular dust wormholes without angle deficit, whose rest frames are homeomorphic to the Schwarzschild-Kruskal manifold or to a 3d torus. The compatibility between the LTB metric and generic f(R) ansatzes furnishes an ‘inverse procedure’ to generate LTB solutions whose sources are found from the f(R) geometry. While the resulting fluids may have an elusive physical interpretation, they can be used as exact non-perturbative toy models in theoretical and cosmological applications of f(R) theories.

Developing a Dust Emission Procedure for Central Asia

Directory of Open Access Journals (Sweden)

Longlei Li

2017-05-01

Full Text Available Airborne mineral dust is thought to have a significant influence on the climate through absorbing and scattering both shortwave and longwave radiations and affecting cloud microphysical processes. However, a knowledge of long-term dust emissions is limited from both temporal and spatial perspectives. Here, we have developed a quantitative climatology: the column-integrated mass of the dust aerosol loading in Central Asia by incorporating the dust module (DuMo into the Weather Research and Forecasting coupled with Chemistry (WRF-Chem model and accounting for regional climate and Land-Cover and Land-Use Changes for the 1950-2010 period in April. This data set is lowly to moderately correlated (0.22-0.48 with the satellite Aerosol Optical Depth in April of the 2000s and lowly correlated (0.02-0.11 with the Absorbing Aerosol Index in April of the 1980s, 1990s, and 2000s. The total dust loading is approximately 207.85 Mton per month in April during the recent decade (2000-2014 over dust source regions. Although only the month of April was simulated, results suggest that trends and magnitudes are captured well, using the WRF-Chem-DuMo.

Infrared spectrophotometry and radiative transfer in optically thick circumstellar dust envelopes

International Nuclear Information System (INIS)

Merrill, K.M.

1976-01-01

The Two-Micron Sky Survey of Neugebauer and Leighton and, more recently, the AFCRL Infrared Sky Survey of Walker and Price have detected numerous compact, isolated, bright infrared sources which are not identified with previously cataloged stars. Observations of many such objects suggest that extensive circumstellar dust envelopes modify the flux from a central source. The present investigations employ broad bandpass photometry at lambda lambda 1.65 μm to 12.5 μm and narrow bandpass spectrophotometry (Δ lambda/lambda approximately 0.015) at lambda lambda 2-4 μm and lambda lambda 8-13 μm to determine the properties of a large sample of such infrared sources. Infrared spectrophotometry can clearly differentiate between normal stars of spectral types M(''oxygen-rich'') and C (''carbon-rich'') on the basis of characteristic absorption bands arising in cool stellar atmospheres. Most of the 2 μ Sky Survey and many of the AFCRL Sky Survey sources appear to be stars of spectral types M and C which are differentiated from normal cool comparison stars only by the presence of extensive circumstellar dust envelopes. Due to the large optical depth of the envelopes, the flux from the star and from the dust cannot be simply separated. Hence solutions of radiative transfer through spherically symmetric envelopes of arbitrary optical depth were generated by a generalized computer code which employed opacities of real dust

Rapid formation of large dust grains in the luminous supernova 2010jl.

Science.gov (United States)

Gall, Christa; Hjorth, Jens; Watson, Darach; Dwek, Eli; Maund, Justyn R; Fox, Ori; Leloudas, Giorgos; Malesani, Daniele; Day-Jones, Avril C