水源保护地农业面源污染防治对策探讨——以昆明松花坝水源保护区为例%Discus on the Prevention and Control Countermeasures of Agricultural Non-point Pollution in Water Source Protected Areas

Institute of Scientific and Technical Information of China (English)

罗婷; 王崇云; 彭明春; 李其阳; 孔维琳; 杨莎; 董磊

2012-01-01

This paper analyzed the contamination sources,pollutants migration processes and causes,which related to water source protection. Best management practices system (BMPs) and ecologic and clean-type small watersheds approaches were two commonly used methods for abating the non-point source (NPS) pollution. We detailedly reviewed the countermeasures in two methods. Then,we took Kunming Songhuaba water protected area as an example to oudine the framework to fight against the NPS pollution,based on the functional zones of water conservation areas,BMPs and ecologic and clean-type small watersheds approaches were specifically elaborated for water protection implements and for agricultural non-point pollution prevention and control. Finally,the paper probed into the NPS pollution control of the water protected areas in future.%分析了水源保护地的污染物来源和迁移过程、形成原因,对最佳管理措施( BMPs)和生态清洁型小流域建设2种水源保护地常用的污染防治对策进行了详细概述；并以昆明松花坝为例,在其水源地保护功能区划的基础上,具体阐述了BMPs与生态清洁小流域建设在水源保护地农业面源污染防治中的应用.最后,探讨了我国水源保护地污染控制的研究方向.

Spatially-Distributed Cost-Effectiveness Analysis Framework to Control Phosphorus from Agricultural Diffuse Pollution.

Directory of Open Access Journals (Sweden)

Runzhe Geng

Full Text Available Best management practices (BMPs for agricultural diffuse pollution control are implemented at the field or small-watershed scale. However, the benefits of BMP implementation on receiving water quality at multiple spatial is an ongoing challenge. In this paper, we introduce an integrated approach that combines risk assessment (i.e., Phosphorus (P index, model simulation techniques (Hydrological Simulation Program-FORTRAN, and a BMP placement tool at various scales to identify the optimal location for implementing multiple BMPs and estimate BMP effectiveness after implementation. A statistically significant decrease in nutrient discharge from watersheds is proposed to evaluate the effectiveness of BMPs, strategically targeted within watersheds. Specifically, we estimate two types of cost-effectiveness curves (total pollution reduction and proportion of watersheds improved for four allocation approaches. Selection of a ''best approach" depends on the relative importance of the two types of effectiveness, which involves a value judgment based on the random/aggregated degree of BMP distribution among and within sub-watersheds. A statistical optimization framework is developed and evaluated in Chaohe River Watershed located in the northern mountain area of Beijing. Results show that BMP implementation significantly (p >0.001 decrease P loss from the watershed. Remedial strategies where BMPs were targeted to areas of high risk of P loss, deceased P loads compared with strategies where BMPs were randomly located across watersheds. Sensitivity analysis indicated that aggregated BMP placement in particular watershed is the most cost-effective scenario to decrease P loss. The optimization approach outlined in this paper is a spatially hierarchical method for targeting nonpoint source controls across a range of scales from field to farm, to watersheds, to regions. Further, model estimates showed targeting at multiple scales is necessary to optimize program

Assessment of the Effectiveness of Green Infrastructure Stormwater Best Management Practices (BMPs) at the Small Watershed Scale

Science.gov (United States)

There have been numerous studies of the water quantity and quality functions of stormwater BMPs at the site scale, but relatively few assessments at the watershed scale. This presentation will present an overview and initial results of projects to evaluate the effectiveness of g...

Optimizing best management practices to control anthropogenic sources of atmospheric phosphorus deposition to inland lakes.

Science.gov (United States)

Weiss, Lee; Thé, Jesse; Winter, Jennifer; Gharabaghi, Bahram

2018-04-18

Excessive phosphorus loading to inland freshwater lakes around the globe has resulted in nuisance plant growth along the waterfronts, degraded habitat for cold water fisheries, and impaired beaches, marinas and waterfront property. The direct atmospheric deposition of phosphorus can be a significant contributing source to inland lakes. The atmospheric deposition monitoring program for Lake Simcoe, Ontario indicates roughly 20% of the annual total phosphorus load (2010-2014 period) is due to direct atmospheric deposition (both wet and dry deposition) on the lake. This novel study presents a first-time application of the Genetic Algorithm (GA) methodology to optimize the application of best management practices (BMPs) related to agriculture and mobile sources to achieve atmospheric phosphorus reduction targets and restore the ecological health of the lake. The novel methodology takes into account the spatial distribution of the emission sources in the airshed, the complex atmospheric long-range transport and deposition processes, cost and efficiency of the popular management practices and social constraints related to the adoption of BMPs. The optimization scenarios suggest that the optimal overall capital investment of approximately $2M, $4M, and $10M annually can achieve roughly 3, 4 and 5 tonnes reduction in atmospheric P load to the lake, respectively. The exponential trend indicates diminishing returns for the investment beyond roughly $3M per year and that focussing much of this investment in the upwind, nearshore area will significantly impact deposition to the lake. The optimization is based on a combination of the lowest-cost, most-beneficial and socially-acceptable management practices that develops a science-informed promotion of implementation/BMP adoption strategy. The geospatial aspect to the optimization (i.e. proximity and location with respect to the lake) will help land managers to encourage the use of these targeted best practices in areas that

A regional protocol for evaluating the effectiveness of forestry best management practices at controlling erosion and sedimentation

Science.gov (United States)

Roger Ryder; Pamela Edwards; Pamela Edwards

2006-01-01

Forestry operations do not have permitting requirements under the Clean Water Act because there is a ccsilvicultural exemption" given in that law, as long as best management practices (BMPs) are used to help control non-point source pollution. However, states' monitoring of BMP effectiveness often has been sporadic and anecdotal, and the procedures used have...

Large-scale performance and design for construction activity erosion control best management practices.

Science.gov (United States)

Faucette, L B; Scholl, B; Beighley, R E; Governo, J

2009-01-01

The National Pollutant Discharge Elimination System (NPDES) Phase II requires construction activities to have erosion and sediment control best management practices (BMPs) designed and installed for site storm water management. Although BMPs are specified on storm water pollution prevention plans (SWPPPs) as part of the construction general permit (GP), there is little evidence in the research literature as to how BMPs perform or should be designed. The objectives of this study were to: (i) comparatively evaluate the performance of common construction activity erosion control BMPs under a standardized test method, (ii) evaluate the performance of compost erosion control blanket thickness, (iii) evaluate the performance of compost erosion control blankets (CECBs) on a variety of slope angles, and (iv) determine Universal Soil Loss Equation (USLE) cover management factors (C factors) for these BMPs to assist site designers and engineers. Twenty-three erosion control BMPs were evaluated using American Society of Testing and Materials (ASTM) D-6459, standard test method for determination of ECB performance in protecting hill slopes from rainfall induced erosion, on 4:1 (H:V), 3:1, and 2:1 slopes. Soil loss reduction for treatments exposed to 5 cm of rainfall on a 2:1 slope ranged from-7 to 99%. For rainfall exposure of 10 cm, treatment soil loss reduction ranged from 8 to 99%. The 2.5 and 5 cm CECBs significantly reduced erosion on slopes up to 2:1, while CECBs or= 4:1 when rainfall totals reach 5 cm. Based on the soil loss results, USLE C factors ranged from 0.01 to 0.9. These performance and design criteria should aid site planners and designers in decision-making processes.

Bone morphogenetic proteins in inflammation, glucose homeostasis and adipose tissue energy metabolism

DEFF Research Database (Denmark)

Grgurevic, Lovorka; Christensen, Gitte Lund; Schulz, Tim J

2016-01-01

implicated in pancreas development as well as control of adult glucose homeostasis. Lastly, we review the recently recognized role of BMPs in brown adipose tissue formation and their consequences for energy expenditure and adiposity. In summary, BMPs play a pivotal role in metabolism beyond their role...... homeostasis (anaemia, hemochromatosis) and oxidative damage. The second and third parts of this review focus on BMPs in the development of metabolic pathologies such as type-2 diabetes mellitus and obesity. The pancreatic beta cells are the sole source of the hormone insulin and BMPs have recently been...

Platelet-rich plasma stimulates osteoblastic differentiation in the presence of BMPs

International Nuclear Information System (INIS)

Tomoyasu, Akihiro; Higashio, Kanji; Kanomata, Kazuhiro; Goto, Masaaki; Kodaira, Kunihiko; Serizawa, Hiroko; Suda, Tatsuo; Nakamura, Atsushi; Nojima, Junya; Fukuda, Toru; Katagiri, Takenobu

2007-01-01

Platelet-rich plasma (PRP) is clinically used as an autologous blood product to stimulate bone formation in vivo. In the present study, we examined the effects of PRP on proliferation and osteoblast differentiation in vitro in the presence of bone morphogenetic proteins (BMPs). PRP and its soluble fraction stimulated osteoblastic differentiation of myoblasts and osteoblastic cells in the presence of BMP-2, BMP-4, BMP-6 or BMP-7. The soluble PRP fraction stimulated osteoblastic differentiation in 3D cultures using scaffolds made of collagen or hydroxyapatite. Moreover, heparin-binding fractions obtained from serum also stimulated osteoblastic differentiation in the presence of BMP-4. These results suggested that platelets contain not only growth factors for proliferation but also novel potentiator(s) for BMP-dependent osteoblastic differentiation

Forestry best management practices and sediment control at skidder stream crossings

Science.gov (United States)

Laura R. Wear; W. Michael Aust; M. Chad Bolding; Brian D. Strahm; Andrew C. Dolloff

2015-01-01

Stream crossings for skid trails have high sediment delivery ratios. Forestry Best Management Practices (BMPs) have proven to be effective for erosion control, but few studies have quantified the impact of various levels of BMPs on sedimentation. In this study, three skid-trail stream-crossing BMP treatments were installed on nine operational stream crossings (three...

The effects of BIG-3 on osteoblast differentiation are not dependent upon endogenously produced BMPs

International Nuclear Information System (INIS)

Gori, Francesca; Demay, Marie B.

2005-01-01

BMPs play an important role in both intramembranous and endochondral ossification. BIG-3, BMP-2-induced gene 3 kb, encodes a WD-40 repeat protein that accelerates the program of osteoblastic differentiation in vitro. To examine the potential interactions between BIG-3 and the BMP-2 pathway during osteoblastic differentiation, MC3T3-E1 cells stably transfected with BIG-3 (MC3T3E1-BIG-3), or with the empty vector (MC3T3E1-EV), were treated with noggin. Noggin treatment of pooled MC3T3E1-EV clones inhibited the differentiation-dependent increase in AP activity observed in the untreated MC3T3E1-EV clones but did not affect the increase in AP activity in the MC3T3E1-BIG-3 clones. Noggin treatment decreased the expression of Runx2 and type I collagen mRNAs and impaired mineralized matrix formation in MC3T3E1-EV clones but not in MC3T3E1-BIG-3 clones. To determine whether the actions of BIG-3 on osteoblast differentiation converged upon the BMP pathway or involved an alternate signaling pathway, Smad1 phosphorylation was examined. Basal phosphorylation of Smad1 was not altered in the MC3T3E1-BIG-3 clones. However, these clones did not exhibit the noggin-dependent decrease in phosphoSmad1 observed in the MC3T3E1-EV clones, nor did it decrease nuclear localization of phosphoSmad1. These observations suggest that BIG-3 accelerates osteoblast differentiation in MC3T3-E1 cells by inducing phosphorylation and nuclear translocation of Smad1 independently of endogenously produced BMPs

Combining Water Quality and Cost-Benefit Analysis to Examine the Implications of Agricultural Best Management Practices

Science.gov (United States)

Rao, N. S.; Easton, Z. M.; Lee, D. R.; Steenhuis, T. S.

2007-12-01

Nutrient runoff from agricultural fields threatens water quality and can impair habitats in many watersheds. Agencies consider these potential risks as they determine acceptable levels of nutrient loading. For example, in the New York City (NYC) watershed, the Environmental Protection Agency's Total Maximum Daily Load (TMDL) for phosphorus (P) has been set at 15μg P L-1 to protect against eutrophication and bacterial outbreaks. In the NYC watersheds agricultural Best Management Practices (BMPs) are the primary means to control nonpoint source P loading. BMPs include riparian buffers, filter strips, manure storage facilities, crop rotation, stripcropping, tree planting and nutrient management plans (NMPs). Water quality research on BMPs to date has included studies on site-specificity of different BMPs, short and long term BMP efficacy, and placement of BMPs with respect to critical source areas. A necessary complement to studies addressing water quality aspects of different BMPs are studies examining the cost-benefit aspects of BMPs. In general, there are installment, maintenance and opportunity costs associated with each BMP, and there are benefits, including cost share agreements between farmers and farm agencies, and increased efficiency of farm production and maintenance. Combining water quality studies and related cost-benefit analyses would help planners and watershed managers determine how best improve water quality. Our research examines the costs-benefit structure associated with BMP scenarios on a one-farm headwater watershed in the Catskill Mountains of NY. The different scenarios include "with and without" BMPs, combinations of BMPs, and different BMP placements across agricultural fields. The costs associated with each BMP scenarios are determined using information from farm agencies and watershed planning agencies. With these data we perform a cost-benefit analysis for the different BMP scenarios and couple the water quality modeling using the

Assessment of stormwater runoff management practices and BMPs under soil sealing: A study case in a peri-urban watershed of the metropolitan area of Rome (Italy).

Science.gov (United States)

Recanatesi, Fabio; Petroselli, Andrea; Ripa, Maria Nicolina; Leone, Antonio

2017-10-01

By 2006, almost 100,000 km 2 of EU soil (2.3% of the whole territory) had been sealed, with a per capita quota of 200 m 2 of sealed surface for each EU citizen. Italy, in 2016, recorded a soil sealing rate of 2.8% of the entire territory. In this context, the urban expansion which occurred in past decades is considered one of the main causes of the increase in flood frequency and intensity in small catchments, causing both social and financial damage. In the present paper, the positive impact of introducing Best Management Practices (BMPs) at urban scale is assessed, with particular regard to the decreasing of flood prone areas. A suburban watershed of the metropolitan area of Rome has been selected for a study case, as its soil sealing rate can be considered paradigmatic at this scale. Starting from the analysis of rainfall events occurring between 2008 and 2011 which caused millions of euros worth of damage, and using a high resolution data set in a GIS environment, two scenarios, with and without BMP introduction, are evaluated applying a rainfall-runoff model and a bidimensional hydraulic model. From a comparison of the flood maps with and without the introduction of BMPs, it was determined that in 90% of the circumstances the employment of the BMPs would completely remove the hydraulic risk, while in the remaining 10% the BMP would at least reduce the areas subjected to flooding. Copyright © 2017 Elsevier Ltd. All rights reserved.

Toward city-scale water quality control: building a theory for smart stormwater systems

Science.gov (United States)

Kerkez, B.; Mullapudi, A. M.; Wong, B. P.

2016-12-01

Urban stormwater systems are rarely designed as actual systems. Rather, it is often assumed that individual Best Management Practices (BMPs) will add up to achieve desired watershed outcomes. Given the rise of BMPs and green infrastructure, we ask: does doing "best" at the local scale guarantee the "best" at the global scale? Existing studies suggest that the system-level performance of distributed stormwater practices may actually adversely impact watersheds by increasing downstream erosion and reducing water quality. Optimizing spatial placement may not be sufficient, however, since precipitation variability and other sources of uncertainty can drive the overall system into undesirable states. To that end, it is also important to control the temporal behavior of the system, which can be achieved by equipping stormwater elements (ponds, wetlands, basins, bioswales, etc.) with "smart" sensors and valves. Rather than building new infrastructure, this permits for existing assets to be repurposed and controlled to adapt to individual storm events. While we have learned how to build and deploy the necessary sensing and control technologies, we do not have a framework or theory that combines our knowledge of hydrology, hydraulics, water quality and control. We discuss the development of such a framework and investigate how existing water domain knowledge can be transferred into a system-theoretic context to enable real-time, city-scale stormwater control. We apply this framework to water quality control in an urban watershed in southeast Michigan, which has been heavily instrumented and retrofitted for control over the past year.

Bmps and id2a act upstream of Twist1 to restrict ectomesenchyme potential of the cranial neural crest.

Directory of Open Access Journals (Sweden)

Ankita Das

Full Text Available Cranial neural crest cells (CNCCs have the remarkable capacity to generate both the non-ectomesenchyme derivatives of the peripheral nervous system and the ectomesenchyme precursors of the vertebrate head skeleton, yet how these divergent lineages are specified is not well understood. Whereas studies in mouse have indicated that the Twist1 transcription factor is important for ectomesenchyme development, its role and regulation during CNCC lineage decisions have remained unclear. Here we show that two Twist1 genes play an essential role in promoting ectomesenchyme at the expense of non-ectomesenchyme gene expression in zebrafish. Twist1 does so by promoting Fgf signaling, as well as potentially directly activating fli1a expression through a conserved ectomesenchyme-specific enhancer. We also show that Id2a restricts Twist1 activity to the ectomesenchyme lineage, with Bmp activity preferentially inducing id2a expression in non-ectomesenchyme precursors. We therefore propose that the ventral migration of CNCCs away from a source of Bmps in the dorsal ectoderm promotes ectomesenchyme development by relieving Id2a-dependent repression of Twist1 function. Together our model shows how the integration of Bmp inhibition at its origin and Fgf activation along its migratory route would confer temporal and spatial specificity to the generation of ectomesenchyme from the neural crest.

Retrofitting impervious urban infrastructure with green technology for rainfall-runoff restoration, indirect reuse and pollution load reduction

International Nuclear Information System (INIS)

Sansalone, John; Raje, Saurabh; Kertesz, Ruben; Maccarone, Kerrilynn; Seltzer, Karl; Siminari, Michele; Simms, Peter; Wood, Brandon

2013-01-01

The built environs alter hydrology and water resource chemistry. Florida is subject to nutrient criteria and is promulgating “no-net-load-increase” criteria for runoff and constituents (nutrients and particulate matter, PM). With such criteria, green infrastructure, hydrologic restoration, indirect reuse and source control are potential design solutions. The study simulates runoff and constituent load control through urban source area re-design to provide long-term “no-net-load-increases”. A long-term continuous simulation of pre- and post-development response for an existing surface parking facility is quantified. Retrofits include a biofiltration area reactor (BAR) for hydrologic and denitrification control. A linear infiltration reactor (LIR) of cementitious permeable pavement (CPP) provides infiltration, adsorption and filtration. Pavement cleaning provided source control. Simulation of climate and source area data indicates re-design achieves “no-net-load-increases” at lower costs compared to standard construction. The retrofit system yields lower cost per nutrient load treated compared to Best Management Practices (BMPs). -- Continuous simulation of climate and site data demonstrate that urban re-design using green infrastructure can provide long-term “no-net-load-increases” at a lower costs compared to BMPs

Evaluating watershed protection programs in New York City's Cannonsville Reservoir source watershed using SWAT-HS

Science.gov (United States)

Hoang, L.; Mukundan, R.; Moore, K. E.; Owens, E. M.; Steenhuis, T. S.

2017-12-01

New York City (NYC)'s reservoirs supply over one billion gallons of drinking water each day to over nine million consumers in NYC and upstate communities. The City has invested more than $1.5 billion in watershed protection programs to maintain a waiver from filtration for the Catskill and Delaware Systems. In the last 25 years, the NYC Department of Environmental Protection (NYCDEP) has implemented programs in cooperation with upstate communities that include nutrient management, crop rotations, improvement of barnyards and manure storage, implementing tertiary treatment for Phosphorus (P) in wastewater treatment plants, and replacing failed septic systems in an effort to reduce P loads to water supply reservoirs. There have been several modeling studies evaluating the effect of agricultural Best Management Practices (BMPs) on P control in the Cannonsville watershed in the Delaware System. Although these studies showed that BMPs would reduce dissolved P losses, they were limited to farm-scale or watershed-scale estimates of reduction factors without consideration of the dynamic nature of overland flow and P losses from variable source areas. Recently, we developed the process-based SWAT-Hillslope (SWAT-HS) model, a modified version of the Soil and Water Assessment Tool (SWAT) that can realistically predict variable source runoff processes. The objective of this study is to use the SWAT-HS model to evaluate watershed protection programs addressing both point and non-point sources of P. SWAT-HS predicts streamflow very well for the Cannonsville watershed with a daily Nash Sutcliffe Efficiency (NSE) of 0.85 at the watershed outlet and NSE values ranging from 0.56 - 0.82 at five other locations within the watershed. Based on good hydrological prediction, we applied the model to predict P loads using detailed P inputs that change over time due to the implementation of watershed protection programs. Results from P model predictions provide improved projections of P

Control of sealed radioactive sources in Peru

International Nuclear Information System (INIS)

Ramirez Quijada, R.

2001-01-01

The paper describes the inventory of radioactive sources in Peru and assesses the control. Three groups of source conditions are established: controlled sources, known sources, and lost and orphan sources. The potential risk, described as not significant, for producing accidents is established and the needed measures are discussed. The paper concludes that, while the control on sealed sources is good, there is still room for improvement. (author)

Performance Probability Distributions for Sediment Control Best Management Practices

Science.gov (United States)

Ferrell, L.; Beighley, R.; Walsh, K.

2007-12-01

Controlling soil erosion and sediment transport can be a significant challenge during the construction process due to the extent and conditions of bare, disturbed soils. Best Management Practices (BMPs) are used as the framework for the design of sediment discharge prevention systems in stormwater pollution prevention plans which are typically required for construction sites. This research focuses on commonly-used BMP systems for perimeter control of sediment export: silt fences and fiber rolls. Although these systems are widely used, the physical and engineering parameters describing their performance are not well understood. Performance expectations are based on manufacturer results, but due to the dynamic conditions that exist on a construction site performance expectations are not always achievable in the field. Based on experimental results product performance is shown to be highly variable. Experiments using the same installation procedures show inconsistent sediment removal performances ranging from (>)85 percent to zero. The goal of this research is to improve the determination of off-site sediment yield based on probabilistic performance results of perimeter control BMPs. BMPs are evaluated in the Soil Erosion Research Laboratory (SERL) in the Civil and Environmental Engineering department at San Diego State University. SERL experiments are performed on a 3-m by 10-m tilting soil bed with a soil depth of 0.5 meters and a slope of 33 percent. The simulated storm event consists of 17 mm/hr for 20 minutes followed by 51 mm/hr for 30 minutes. The storm event is based on an ASTM design storm intended to simulate BMP failures. BMP performance is assessed based on experiments where BMPs are installed per manufacture specifications, less than optimal installations, and no treatment conditions. Preliminary results from 30 experiments are presented and used to develop probability distributions for BMP sediment removal efficiencies. The results are then combined with

Analysis of the efficacy and cost-effectiveness of best management practices for controlling sediment yield: A case study of the Joumine watershed, Tunisia.

Science.gov (United States)

Mtibaa, Slim; Hotta, Norifumi; Irie, Mitsuteru

2018-03-01

Soil erosion can be reduced through the strategic selection and placement of best management practices (BMPs) in critical source areas (CSAs). In the present study, the Soil Water Assessment Tool (SWAT) model was used to identify CSAs and investigate the effectiveness of different BMPs in reducing sediment yield in the Joumine watershed, an agricultural river catchment located in northern Tunisia. A cost-benefit analysis (CBA) was used to evaluate the cost-effectiveness of different BMP scenarios. The objective of the present study was to determine the most cost-effective management scenario for controlling sediment yield. The model performance for the simulation of streamflow and sediment yield at the outlet of the Joumine watershed was good and satisfactory, respectively. The model indicated that most of the sediment was originated from the cultivated upland area. About 34% of the catchment area consisted of CSAs that were affected by high to very high soil erosion risk (sediment yield >10t/ha/year). Contour ridges were found to be the most effective individual BMP in terms of sediment yield reduction. At the watershed level, implementing contour ridges in the CSAs reduced sediment yield by 59%. Combinations of BMP scenarios were more cost-effective than the contour ridges alone. Combining buffer strips (5-m width) with other BMPs depending on land slope (> 20% slope: conversion to olive orchards; 10-20% slope: contour ridges; 5-10% slope: grass strip cropping) was the most effective approach in terms of sediment yield reduction and economic benefits. This approach reduced sediment yield by 61.84% with a benefit/cost ratio of 1.61. Compared with the cost of dredging, BMPs were more cost-effective for reducing sediment loads to the Joumine reservoir, located downstream of the catchment. Our findings may contribute to ensure the sustainability of future conservation programs in Tunisian regions. Copyright © 2017 Elsevier B.V. All rights reserved.

Neutron generator tube ion source control

International Nuclear Information System (INIS)

Bridges, J.R.

1982-01-01

A system is claimed for controlling the output of a neutron generator tube of the deuterium-tritium accelerator type and having an ion source to produce sharply defined pulses of neutrons for well logging use. It comprises: means for inputting a relatively low voltage input control pulse having a leading edge and a trailing edge; means, responsive to the input control pulse, for producing a relatively high voltage ion source voltage pulse after receipt of the input pulse; and means, responsive to the input control pulse, for quenching, after receipt of the input pulse, the ion source control pulse, thereby providing a sharply time defined neutron output from the generator tube

Putting people into water quality modelling.

Science.gov (United States)

Strickert, G. E.; Hassanzadeh, E.; Noble, B.; Baulch, H. M.; Morales-Marin, L. A.; Lindenschmidt, K. E.

2017-12-01

Water quality in the Qu'Appelle River Basin, Saskatchewan is under pressure due to nutrient pollution entering the river system from major cities, industrial zones and agricultural areas. Among these stressors, agricultural activities are basin-wide; therefore, they are the largest non-point source of water pollution in this region. The dynamics of agricultural impacts on water quality are complex and stem from decisions and activities of two distinct stakeholder groups, namely grain farmers and cattle producers, which have different business plans, values, and attitudes towards water quality. As a result, improving water quality in this basin requires engaging with stakeholders to: (1) understand their perspectives regarding a range of agricultural Beneficial Management Practices (BMPs) that can improve water quality in the region, (2) show them the potential consequences of their selected BMPs, and (3) work with stakeholders to better understand the barriers and incentives to implement the effective BMPs. In this line, we held a series of workshops in the Qu'Appelle River Basin with both groups of stakeholders to understand stakeholders' viewpoints about alternative agricultural BMPs and their impact on water quality. Workshop participants were involved in the statement sorting activity (Q-sorts), group discussions, as well as mapping activity. The workshop outcomes show that stakeholder had four distinct viewpoints about the BMPs that can improve water quality, i.e., flow and erosion control, fertilizer management, cattle site management, as well as mixed cattle and wetland management. Accordingly, to simulate the consequences of stakeholder selected BMPs, a conceptual water quality model was developed using System Dynamics (SD). The model estimates potential changes in water quality at the farm, tributary and regional scale in the Qu'Appelle River Basin under each and/or combination of stakeholder selected BMPs. The SD model was then used for real

Regulatory Control of Radioactive Sources in Spain

Energy Technology Data Exchange (ETDEWEB)

Rodriguez, M.; Martin, J.L., E-mail: mrm@csn.es [Nuclear Safety Council, Madrid (Spain)

2011-07-15

The arrangements for the regulatory control of the safety and security of sealed radioactive sources in Spain are described. Emphasis is given to the situations which are most likely to result in the loss of control of sources and on the procedures introduced to reduce the likelihood of losses in these cases. Finally, the strategy for locating sources which have been lost from control (orphan sources) is described. (author)

Control system for Siam photon source

CERN Document Server

Apiwatwaja, R; Isoyama, G; Ishii, T; Pairsuwan, W

2003-01-01

A new computer control system has been developed for Siam photon source, which is the first synchrotron light source in Thailand, personal computers and PLC's have been employed which are connected together through Ethernet. Man Machine Interface Stations (MMIS) at the front end act as a graphical user interface within Windows environment. The monitoring and controlling of individual devices is handled through several pairs of digital control station and the device interface located in each part of the synchrotron complex. The installation of the control system has been completed. The commissioning test of the control system is underway and the reliability of the system is on the positive side. Details of commissioning tests as well as characteristics of this newly built control system for the Siam photon source are described in this report.

Factors Influencing Farmers’ Adoption of Best Management Practices: A Review and Synthesis

Science.gov (United States)

Best management practices (BMPs) for reducing agricultural non-point source pollution are widely available. However, agriculture remains a major global contributor to degradation of waters because farmers often do not adopt BMPs. To improve water quality, it is necessary to under...

Model predictive control for Z-source power converter

DEFF Research Database (Denmark)

Mo, W.; Loh, P.C.; Blaabjerg, Frede

2011-01-01

This paper presents Model Predictive Control (MPC) of impedance-source (commonly known as Z-source) power converter. Output voltage control and current control for Z-source inverter are analyzed and simulated. With MPC's ability of multi- system variables regulation, load current and voltage...

The IAEA and Control of Radioactive Sources

International Nuclear Information System (INIS)

Dodd, B.

2004-01-01

The presentation discusses the authoritative functions and the departments of the IAEA, especially the Department of Nuclear Safety and Security and its Safety and Security of Radiation Sources Unit. IAEA safety series and IAEA safety standards series inform about international standards, provide underlying principles, specify obligations and responsibilities and give recommendations to support requirements. Other IAEA relevant publications comprise safety reports, technical documents (TECDOCs), conferences and symposium papers series and accident reports. Impacts of loss of source control is discussed, definitions of orphan sources and vulnerable sources is given. Accidents with orphan sources, radiological accidents statistic (1944-2000) and its consequences are discussed. These incidents lead to development of the IAEA guidance. The IAEA's action plan for the safety of radiation sources and the security of radioactive material was approved by the IAEA Board of Governors and the General Conference in September 1999. This led to the 'Categorization of Radiation Sources' and the 'Code of Conduct on the Safety and Security of Radioactive Sources'. After 0911 the IAEA developed a nuclear security plan of activities including physical protection of nuclear material and nuclear facilities, detection of malicious activities involving nuclear and other radioactive materials, state systems for nuclear material accountancy and control, security of radioactive material other than nuclear material, assessment of safety and security related vulnerability of nuclear facilities, response to malicious acts, or threats thereof, adherence to and implementation of international agreements, guidelines and recommendations and nuclear security co-ordination and information management. The remediation of past problems comprised collection and disposal of known disused sources, securing vulnerable sources and especially high-risk sources (Tripartite initiative), searching for

Forestry Best Management Practices Relationships with Aquatic and Riparian Fauna: A Review

Directory of Open Access Journals (Sweden)

Brooke M. Warrington

2017-09-01

Full Text Available Forestry best management practices (BMPs were developed to minimize water pollution from forestry operations by primarily addressing sediment and sediment transport, which is the leading source of pollution from silviculture. Implementation of water quality BMPs may also benefit riparian and aquatic wildlife, although wildlife benefits were not driving forces for BMP development. Therefore, we reviewed literature regarding potential contributions of sediment-reducing BMPs to conservation of riparian and aquatic wildlife, while realizing that BMPs also minimize thermal, nutrient, and chemical pollution. We reached five important conclusions: (1 a significant body of research confirms that forestry BMPs contribute to the protection of water quality and riparian forest structure; (2 data-specific relationships between forestry BMPs and reviewed species are limited; (3 forestry BMPs for forest road construction and maintenance, skid trails, stream crossings, and streamside management zones (SMZs are important particularly for protection of water quality and aquatic species; (4 stream crossings should be carefully selected and installed to minimize sediment inputs and stream channel alterations; and (5 SMZs promote retention of older-age riparian habitat with benefits extending from water bodies to surrounding uplands. Overall, BMPs developed for protection of water quality should benefit a variety of riparian and aquatic species that are sensitive to changes in water quality or forest structure.

Forestry best management practices relationships with aquatic and riparian fauna: A review

Science.gov (United States)

Warrington, Brooke M.; Aust, W. Michael; Barrett, Scott M.; Ford, W. Mark; Dolloff, C. Andrew; Schilling, Erik B.; Wigley, T. Bently; Bolding, M. Chad

2017-01-01

Forestry best management practices (BMPs) were developed to minimize water pollution from forestry operations by primarily addressing sediment and sediment transport, which is the leading source of pollution from silviculture. Implementation of water quality BMPs may also benefit riparian and aquatic wildlife, although wildlife benefits were not driving forces for BMP development. Therefore, we reviewed literature regarding potential contributions of sediment-reducing BMPs to conservation of riparian and aquatic wildlife, while realizing that BMPs also minimize thermal, nutrient, and chemical pollution. We reached five important conclusions: (1) a significant body of research confirms that forestry BMPs contribute to the protection of water quality and riparian forest structure; (2) data-specific relationships between forestry BMPs and reviewed species are limited; (3) forestry BMPs for forest road construction and maintenance, skid trails, stream crossings, and streamside management zones (SMZs) are important particularly for protection of water quality and aquatic species; (4) stream crossings should be carefully selected and installed to minimize sediment inputs and stream channel alterations; and (5) SMZs promote retention of older-age riparian habitat with benefits extending from water bodies to surrounding uplands. Overall, BMPs developed for protection of water quality should benefit a variety of riparian and aquatic species that are sensitive to changes in water quality or forest structure.

Advanced Light Source control system

International Nuclear Information System (INIS)

Magyary, S.; Chin, M.; Cork, C.; Fahmie, M.; Lancaster, H.; Molinari, P.; Ritchie, A.; Robb, A.; Timossi, C.

1989-03-01

The Advanced Light Source (ALS) is a third generation 1--2 GeV synchrotron radiation source designed to provide ports for 60 beamlines. It uses a 50 MeV electron linac and 1.5 GeV, 1 Hz, booster synchrotron for injection into a 1--2 GeV storage ring. Interesting control problems are created because of the need for dynamic closed beam orbit control to eliminate interaction between the ring tuning requirements and to minimize orbit shifts due to ground vibrations. The extremely signal sensitive nature of the experiments requires special attention to the sources of electrical noise. These requirements have led to a control system design which emphasizes connectivity at the accelerator equipment end and a large I/O bandwidth for closed loop system response. Not overlooked are user friendliness, operator response time, modeling, and expert system provisions. Portable consoles are used for local operation of machine equipment. Our solution is a massively parallel system with >120 Mbits/sec I/O bandwidth and >1500 Mips computing power. At the equipment level connections are made using over 600 powerful Intelligent Local Controllers (ILC-s) mounted in 3U size Eurocard slots using fiber-optic cables between rack locations. In the control room, personal computers control and display all machine variables at a 10 Hz rate including the scope signals which are collected though the control system. Commercially available software and industry standards are used extensively. Particular attention is paid to reliability, maintainability and upgradeability. 10 refs., 11 figs

The Influence of Perceptions of Practice Characteristics: An Examination of Agricultural Best Management Practice Adoption in Two Indiana Watersheds

Science.gov (United States)

Reimer, Adam P.; Weinkauf, Denise Klotthor; Prokopy, Linda Stalker

2012-01-01

Agricultural best management practices (BMPs), or conservation practices, can help reduce nonpoint source pollution from agricultural lands, as well as provide valuable wildlife habitat. There is a large literature exploring factors that lead to a producer's voluntary adoption of BMPs, but there have been inconsistent findings. Generally, this…

Stormwater management impacts on urban stream water quality and quantity during and after development in Clarksburg, MD

Science.gov (United States)

Loperfido, J. V.; Noe, G. B.; Jarnagin, S.; Mohamoud, Y. M.; Van Ness, K.; Hogan, D. M.

2012-12-01

Urbanization and urban land use leads to degradation of local stream habitat and 'urban stream syndrome.' Best Management Practices (BMPs) are often used in an attempt to mitigate the impact of urban land use on stream water quality and quantity. Traditional development has employed stormwater BMPs that were placed in a centralized manner located either in the stream channel or near the riparian zone to treat stormwater runoff from large drainage areas; however, urban streams have largely remained impaired. Recently, distributed placement of BMPs throughout the landscape has been implemented in an attempt to detain, treat, and infiltrate stormwater runoff from smaller drainage areas near its source. Despite increasing implementation of distributed BMPs, little has been reported on the catchment-scale (1-10 km^2) performance of distributed BMPs and how they compare to centralized BMPs. The Clarksburg Special Protection Area (CSPA), located in the Washington, DC exurbs within the larger Chesapeake Bay watershed, is undergoing rapid urbanization and employs distributed BMPs on the landscape that treat small drainage areas with the goal of preserving high-quality stream resources in the area. In addition, the presence of a nearby traditionally developed (centralized BMPs) catchment and an undeveloped forested catchment makes the CSPA an ideal setting to understand how the best available stormwater management technology implemented during and after development affects stream water quality and quantity through a comparative watershed analysis. The Clarksburg Integrated Monitoring Partnership is a consortium of local and federal agencies and universities that conducts research in the CSPA including: monitoring of stream water quality, geomorphology, and biology; analysis of stream hydrological and water quality data; and GIS mapping and analysis of land cover, elevation change and BMP implementation data. Here, the impacts of urbanization on stream water quantity

EPICS application source/release control

International Nuclear Information System (INIS)

Zieman, B.; Anderson, J.; Kraimer, M.

1995-01-01

This manual describes a set of Application Source/Release Control tools (appSR) that can be used to develop software for EPICS based control systems. The Application Source/Release Control System (appSR) has been unbundled from base EPICS and is now available as an EPICS extension. Due to this unbundling, two new directories must be added to a user's path (see section ''Environment'' on page 3 for more information) and a new command getapp must be issued after the getrel command to get a specific version of appSR (see section ''Creating The Initial Application System Area'' on page 7 for more information). It is now required that GNU make version 3.71 or later be used for makes instead of SUN make. Users should now type gmake instead of make

Automatic control of a negative ion source

International Nuclear Information System (INIS)

Saadatmand, K.; Sredniawski, J.; Solensten, L.

1989-01-01

A CAMAC based control architecture is devised for a Berkeley-type H - volume ion source. The architecture employs three 80386 PCs. One PC is dedicated to control and monitoring of source operation. The other PC functions with digitizers to provide data acquisition of waveforms. The third PC is used for off-line analysis. Initially, operation of the source was put under remote computer control (supervisory). This was followed by development of an automated startup procedure. Finally, a study of the physics of operation is now underway to establish a data base from which automatic beam optimization can be derived. (orig.)

Automatic control of a negative ion source

Science.gov (United States)

Saadatmand, K.; Sredniawski, J.; Solensten, L.

1989-04-01

A CAMAC based control architecture is devised for a Berkeley-type H - volume ion source [1]. The architecture employs three 80386 TM PCs. One PC is dedicated to control and monitoring of source operation. The other PC functions with digitizers to provide data acquisition of waveforms. The third PC is used for off-line analysis. Initially, operation of the source was put under remote computer control (supervisory). This was followed by development of an automated startup procedure. Finally, a study of the physics of operation is now underway to establish a data base from which automatic beam optimization can be derived.

Automatic control of a negative ion source

Energy Technology Data Exchange (ETDEWEB)

Saadatmand, K.; Sredniawski, J.; Solensten, L. (Grumman Corp., Long Island, NY (USA))

1989-04-01

A CAMAC based control architecture is devised for a Berkeley-type H/sup -/ volume ion source. The architecture employs three 80386 PCs. One PC is dedicated to control and monitoring of source operation. The other PC functions with digitizers to provide data acquisition of waveforms. The third PC is used for off-line analysis. Initially, operation of the source was put under remote computer control (supervisory). This was followed by development of an automated startup procedure. Finally, a study of the physics of operation is now underway to establish a data base from which automatic beam optimization can be derived. (orig.).

Control of sources of ionizing radiation in Lithuania

International Nuclear Information System (INIS)

Mastauskas, Albinas; Ziliukas, Julius; Morkunas, Gendrutis

1997-01-01

Aspects connected with regulatory control of radioactive sources in Lithuania, such as keeping of the computer-based registry, investigation of arrested illegal radioactive material, decision making, control of users of radioactive sources are discussed. Most of the sources of ionizing radiation are smoke detectors and x-ray equipment. Potentially most dangerous sources (both sealed and unsealed) of therapy and industry are also presented

Control of radiation sources in Japan

International Nuclear Information System (INIS)

Maki, S.

2001-01-01

The report refers to the regulations for radioactive material in force in Japan, and to the organizations with responsibilities for regulating radiation sources. An outline of the law regulating the use of radiation sources and radioactive materials is provided, including its scope, types of radiation sources under control, exemptions and the system of notification, authorization and inspection. The experience of Japan with orphan sources is presented in three different cases, and the measures carried out to store the orphan sources in safe conditions. (author)

Strengthening control over radioactive sources in authorized use and regaining control over orphan sources. National strategies

International Nuclear Information System (INIS)

2004-02-01

The objective of this report is to provide practical guidance to States on the development of a national strategy for improving control over radioactive sources, particularly dangerous sources (Categories 1-3). Part of this process involves the determination of the magnitude of the potential problem with orphan and vulnerable sources and indeed, whether or not a national strategy is needed. The ultimate objective is that States will use this report to develop and then implement a plan of action that will result in all significant sources being managed in a safe and secure manner. This report attempts to provide both the background knowledge and the methodology necessary for an individual or small team of responsible persons to develop a national strategy for improving control over all radioactive sources, but especially orphan and vulnerable sources. The background knowledge given in Chapter 3 is an update of the information on practices that was given in IAEA-TECDOC-804, which focused on spent radioactive sources. After some introductory material, this report provides both the factual information and the general steps needed to develop and implement a national strategy. Part I contains background information for those who are not already familiar with the subject including the need for national strategies, the generic causes of loss of control of sources, with specific examples and the common applications of radioactive sources. Part II details the actual process for the development and implementation of a national strategy, which includes assessing the problem by first gathering specific and national information, determining the nature and magnitude of the problem, developing the national strategy by evaluating, and prioritizing possible solutions, implementing the strategy subsequent to a high level decision; and evaluating the effectiveness of the plan and making changes as a result until the desired objective is achieved. Searches for sources will be part of

Inadequate control of world's radioactive sources

International Nuclear Information System (INIS)

2002-01-01

The radioactive materials needed to build a 'dirty bomb' can be found in almost any country in the world, and more than 100 countries may have inadequate control and monitoring programs necessary to prevent or even detect the theft of these materials. The IAEA points out that while radioactive sources number in the millions, only a small percentage have enough strength to cause serious radiological harm. It is these powerful sources that need to be focused on as a priority. In a significant recent development, the IAEA, working in collaboration with the United States Department of Energy (DOE) and the Russian Federation's Ministry for Atomic Energy (MINATOM), have established a tripartite working group on 'Securing and Managing Radioactive Sources'. Through its program to help countries improve their national infrastructures for radiation safety and security, the IAEA has found that more than 100 countries may have no minimum infrastructure in place to properly control radiation sources. However, many IAEA Member States - in Africa, Asia, Latin America, and Europe - are making progress through an IAEA project to strengthen their capabilities to control and regulate radioactive sources. The IAEA is also concerned about the over 50 countries that are not IAEA Member States (there are 134), as they do not benefit from IAEA assistance and are likely to have no regulatory infrastructure. The IAEA has been active in lending its expertise to search out and secure orphaned sources in several countries. More than 70 States have joined with the IAEA to collect and share information on trafficking incidents and other unauthorized movements of radioactive sources and other radioactive materials. The IAEA and its Member States are working hard to raise levels of radiation safety and security, especially focusing on countries known to have urgent needs. The IAEA has taken the leading role in the United Nations system in establishing standards of safety, the most significant of

A Manual to Identify Sources of Fluvial Sediment | Science ...

Science.gov (United States)

Sedimentation is one of the main causes of stream/river aquatic life use impairments in R3. Currently states lack standard guidance on appropriate tools available to quantify sediment sources and develop sediment budgets in TMDL Development. Methods for distinguishing sediment types for TMDL development will focus stream restoration and soil conservation efforts in strategic locations in a watershed and may better target appropriate BMPs to achieve sediment load reductions. Properly identifying sediment sources in a TMDL will also help focus NPDES permitting, stream restoration activities and other TMDL implementation efforts. This project will focus on developing a framework that will be published as a guidance document that outlines steps and approaches to identify the significant sources of fine-grained sediment in 303D listed watersheds. In this framework, the sediment-fingerprinting and sediment budget approaches will be emphasized. This project will focus on developing a framework that will be published as a guidance document that outlines steps and approaches to identify the significant sources of fine-grained sediment in 303D listed watersheds. In this framework, the sediment-fingerprinting and sediment budget approaches will be emphasized.

Control of sources of ionizing radiation in Lithuania

Energy Technology Data Exchange (ETDEWEB)

Mastauskas, Albinas; Ziliukas, Julius; Morkunas, Gendrutis [Radiation Protection Centre, Vilnius (Lithuania)

1997-12-31

Aspects connected with regulatory control of radioactive sources in Lithuania, such as keeping of the computer-based registry, investigation of arrested illegal radioactive material, decision making, control of users of radioactive sources are discussed. Most of the sources of ionizing radiation are smoke detectors and x-ray equipment. Potentially most dangerous sources (both sealed and unsealed) of therapy and industry are also presented 2 refs., 2 tabs.; e-mail: rsc at post.omnitel.net

Neutron generator tube ion source control apparatus

International Nuclear Information System (INIS)

Bridges, J.R.

1982-01-01

A pulsed neutron well logging system includes a neutron generator tube of the deuterium-tritium accelerator type and an ion source control apparatus providing extremely sharply time-defined neutron pulses. A low voltage control pulse supplied to an input by timing circuits turns a power FET on via a buffer-driver whereby a 2000 volt pulse is produced in the secondary of a pulse transformer and applied to the ion source of the tube. A rapid fall in this ion source control pulse is ensured by a quenching circuit wherein a one-shot responds to the falling edge of the control pulse and produces a 3 microsecond delay to compensate for the propagation delay. A second one-shot is triggered by the falling edge of the output of the first one-shot and gives an 8 microsecond pulse to turn on the power FET which, via an isolation transformer turns on a series-connected transistor to ground the secondary of the pulse transformer and the ion source. (author)

Time-lapse controlled-source electromagnetics using interferometry

NARCIS (Netherlands)

Hunziker, J.W.; Slob, E.C.; Wapenaar, C.P.A.

In time-lapse controlled-source electromagnetics, it is crucial that the source and the receivers are positioned at exactly the same location at all times of measurement. We use interferometry by multidimensional deconvolution (MDD) to overcome problems in repeatability of the source location.

Urban stormwater source control policies: why and how?

Directory of Open Access Journals (Sweden)

G. Petrucci

2014-09-01

Full Text Available Stormwater source control is becoming a common strategy for urban stormwater management in many countries. It relies on regulations or other policy instruments compelling or inciting implementation, for each new urban development, of small-scale facilities to locally store and manage stormwater. Local authorities that pioneered source control since the 1980s have already observed that small-scale facilities systematically implemented over a catchment are able to influence its hydrological behaviour. This capability is the main strength of source control, as it allows compensation for the negative effects of urbanization. Yet, it also represents its main risk: if initial decision-making is not sufficiently accurate, source control can produce long-term negative effects. Because of its current spreading, source control will acquire an increasing role as a driver of hydrological changes in urban catchments, and the directions of these changes depend on current policy-making practices. This paper presents an analysis and a critical discussion of the main objectives that policy-makers attribute to stormwater source control. The investigation is based on a sample of French case studies, completed by a literature review for international comparison. It identifies four main objectives, some typical of urban stormwater management and some more innovative: flood reduction, receiving waters protection, sustainable development, costs reduction. The discussion focuses on how current policy-making practices are able to translate these objectives in concrete policy instruments, and on which knowledge and tools could improve this process. It is shown that for some objectives, basic knowledge is available, but the creation of policy instruments which are effective at the catchment scale and adapted to local conditions is still problematic. For other objectives, substantial lacks of knowledge exist, casting doubts on long-term effectiveness of current policy

Orphan sources control in the Republic of Korea

International Nuclear Information System (INIS)

Kim, C.-W.

2001-01-01

In this paper, the orphan source control programme in Korea will be discussed. Orphan sources are, in general, classified into three groups: 1) Illegally trafficking radioactive sources; 2) Domestic loss of radioactive sources due to the bankruptcy of licensees or authorized suppliers; and 3) Contaminated metal scrap, which has been imported. There are, currently, two approaches going on to control and manage orphan sources in Korea. First, the Korean regulatory authority (Ministry of Science and Technology: MOST) will fully run an information system on radiation safety to effectively trace and monitor all radioactive sources in the country by the year 2001. Second, the regulatory authority strongly advises steel mill companies to closely scrutinize and inspect scrap metal through a scrap monitoring system when they attempt to reutilize it in order to prevent it from being contaminated by uncontrolled sources. The Korea Institute of Nuclear Safety (KINS), a regulatory expert organization, is carrying out a three-year multiphase project to control and monitor orphan sources in Korea. The system, called the Information System on Integrated Radiation Safety (ISIRS) on the inter- and intra-net system has been developed to effectively control and accurately monitor radioactive sources on a real time basis since 1998. If the system is successfully set up as scheduled by the middle of May next year, the regulatory authority will be able to control any reutilization of uncontrolled sources efficiently. At the same time, the system can also provide, not only licensees, suppliers, or perspective end users but also the Korean general public of interests with information on radiation safety, safe radiation management tools and public services. The system has been created because of the necessity to effectively control radioactive sources safely. Also, it serves to prepare necessary protective measures in a timely manner for abnormal events of uncontrolled radiation from

Software architecture considerations for ion source control systems

International Nuclear Information System (INIS)

Sinclair, J.W.

1997-09-01

General characteristics of distributed control system software tools are examined from the perspective of ion source control system requirements. Emphasis is placed on strategies for building extensible, distributed systems in which the ion source element is one component of a larger system. Vsystem, a commercial software tool kit from Vista Control Systems was utilized extensively in the control system upgrade of the Holifield Radioactive Ion Beam Facility. Part of the control system is described and the characteristics of Vsystem are examined and compared with those of EPICS, the Experimental Physics and Industrial Control System

The regulatory control of ionizing radiation sources in Lithuania

International Nuclear Information System (INIS)

Mastauskas, A.; Ziliukas, J.; Morkunas, G.

1998-01-01

The Radiation Protection Centre of the Ministry of Health is the regulatory authority responsible for radiation protection of the public and of workers using sources of ionizing radiation in Lithuania. One of its responsibilities is the control of radioactive sources, which includes keeping the registry, investigating persons arrested while illegally carrying or in possession of radioactive material, decision making and control of users of radioactive sources. The computer based registry contains a directory of more than 24,000 sources and some 800 users in research, medicine and industry. Most of these sources are found in smoke detectors and X ray equipment. The potentially most dangerous sources for therapy and industry (sealed and unsealed) are also listed in this registry. Problems connected with the regulatory control of radioactive sources in Lithuania are presented and their solution is discussed. (author)

Control of sealed sources and equipments used in gammagraphy

International Nuclear Information System (INIS)

Sahyun, A.; Sordi, G.-M.A.A.; Biazzini Filho, F.L.

1988-01-01

The Radiation Protection Department of the IPEN-CNEN/SP, in 1987, formed a section incharged to control all radioactive material: a) received by the IPEN-CNEN/SP; b) produced by the IPEN-CNEN/SP; c) delivered from the IPEN-CNEN/SP. The aim of this section is to maintain a permanent control of all radioactive sources movement got at the IPEN-CNEN/SP. This control is performed with a microcomputer, trademark MICRODIGITAL, model TK3000 //e, 256 KBytes of memory, utilizing the TOTALWORKS program. This program permits to have the origin, characteristics and address of the radioactive sources, its sites in the IPEN, its uses, etc. Already we have put in the microcomputer, the control of the sealed sources produced used in nondestructive test, the inspection control of the gamagraphy irradiator and the control of the depleted sources. The next step is to introduce in the computer the inspection of the remote control of the irradiator. The aim of this paper is to describe the control program that was already put on. This radioactive material control was started with the sealed sources used in gamagraphy because we believe that is the field with the most likelihood of accident in the population, and therefore it's that need the most hard control about the site and the performance of the irradiation facility. (author) [pt

Nitrogen component in nonpoint source pollution models

Science.gov (United States)

Pollutants entering a water body can be very destructive to the health of that system. Best Management Practices (BMPs) and/or conservation practices are used to reduce these pollutants, but understanding the most effective practices is very difficult. Watershed models are an effective tool to aid...

Proteínas morfogenéticas óseas (BMPs): Efecto de la proteína osteogénica-1 (OP-l/BMP-7) en la condrogénesis y osteogenesis

OpenAIRE

Peris Serra, José Luis; Prat Pastor, Jaime; Dejoz, Ricardo; Comín Clavijo, Mario; Atienza Vicente, Carlos M.; Barreda, J. S.; Roger, I.; Reig, C.; Vera Luna, Pedro

1996-01-01

En la actualidad, los estudios sobre biología molecular han facilitado el análisis de ciertos factores de transformación del crecimiento tipo ß(TGF-ß)I, entre los que destaca una familia de proteínas morfogenéticas óseas (BMPs). Las técnicas de ingeniería genética han permitido replicar alguno de estos factores y localizar los genes que codifican dichas proteínas. La proteína osteogenics-1 (OP-1) ha sido caracterizada y sintetizada in vitro y muestra un elevado potencial osteog...

10 CFR 36.31 - Control of source movement.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Control of source movement. 36.31 Section 36.31 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR IRRADIATORS Design and Performance Requirements for Irradiators § 36.31 Control of source movement. (a) The mechanism that moves the...

Evaluation of nonpoint-source contamination, Wisconsin; selected streamwater-quality data, land-use and best-management practices inventory, and quality assurance and quality control, water year 1993

Science.gov (United States)

Corsi, Steven R.; Walker, John F.; Graczyk, D.J.; Greb, S.R.; Owens, D.W.; Rappold, K.F.

1995-01-01

The objective of the watershed-management evaluation monitoring program in Wisconsin is to evaluate the effectiveness of the best-management practices (BMPs) for rural streams, urban streams, and urban storm sewers. This report is an annual summary of the data collected for the program and a report of the results from several different special studies conducted within this program.

Evaluation of non-point source pollution reduction by applying best management practices using a SWAT model and QuickBird high resolution satellite imagery.

Science.gov (United States)

Lee, MiSeon; Park, GeunAe; Park, MinJi; Park, JongYoon; Lee, JiWan; Kim, SeongJoon

2010-01-01

This study evaluated the reduction effect of non-point source pollution by applying best management practices (BMPs) to a 1.21 km2 small agricultural watershed using a SWAT (Soil and Water Assessment Tool) model. Two meter QuickBird land use data were prepared for the watershed. The SWAT was calibrated and validated using daily streamflow and monthly water quality (total phosphorus (TP), total nitrogen (TN), and suspended solids (SS)) records from 1999 to 2000 and from 2001 to 2002. The average Nash and Sutcliffe model efficiency was 0.63 for the streamflow and the coefficients of determination were 0.88, 0.72, and 0.68 for SS, TN, and TP, respectively. Four BMP scenarios viz. the application of vegetation filter strip and riparian buffer system, the regulation of Universal Soil Loss Equation P factor, and the fertilizing control amount for crops were applied and analyzed.

Respiratory source control using a surgical mask: An in vitro study.

Science.gov (United States)

Patel, Rajeev B; Skaria, Shaji D; Mansour, Mohamed M; Smaldone, Gerald C

2016-07-01

Cough etiquette and respiratory hygiene are forms of source control encouraged to prevent the spread of respiratory infection. The use of surgical masks as a means of source control has not been quantified in terms of reducing exposure to others. We designed an in vitro model using various facepieces to assess their contribution to exposure reduction when worn at the infectious source (Source) relative to facepieces worn for primary (Receiver) protection, and the factors that contribute to each. In a chamber with various airflows, radiolabeled aerosols were exhaled via a ventilated soft-face manikin head using tidal breathing and cough (Source). Another manikin, containing a filter, quantified recipient exposure (Receiver). The natural fit surgical mask, fitted (SecureFit) surgical mask and an N95-class filtering facepiece respirator (commonly known as an "N95 respirator") with and without a Vaseline-seal were tested. With cough, source control (mask or respirator on Source) was statistically superior to mask or unsealed respirator protection on the Receiver (Receiver protection) in all environments. To equal source control during coughing, the N95 respirator must be Vaseline-sealed. During tidal breathing, source control was comparable or superior to mask or respirator protection on the Receiver. Source control via surgical masks may be an important adjunct defense against the spread of respiratory infections. The fit of the mask or respirator, in combination with the airflow patterns in a given setting, are significant contributors to source control efficacy. Future clinical trials should include a surgical mask source control arm to assess the contribution of source control in overall protection against airborne infection.

Synthetic aperture controlled source electromagnetics

NARCIS (Netherlands)

Fan, Y.; Snieder, R.; Slob, E.; Hunziker, J.W.; Singer, J.; Sheiman, J.; Rosenquist, M.

2010-01-01

Controlled?source electromagnetics (CSEM) has been used as a de?risking tool in the hydrocarbon exploration industry. Although there have been successful applications of CSEM, this technique is still not widely used in the industry because the limited types of hydrocarbon reservoirs CSEM can detect.

Establishing control over nuclear materials and radiation sources in Georgia

International Nuclear Information System (INIS)

Basilia, G.

2010-01-01

Regulatory control over radiation sources in Georgia was lost after disintegration of the Soviet Union. A number of radiation accidents and illegal events occurred in Georgia. From 1999 Nuclear and Radiation Safety Service of the Ministry of Environmental Protection and Natural Resources is responsible for regulatory control over radiation sources in Georgia. US NRC Regulatory Assistance Program in Georgia Assist the Service in establishing long term regulatory control over sources. Main focuses of US NRC program are country-wide inventory, create National Registry of sources, safe storage of disused sources, upgrade legislation and regulation, implementation licensing and inspection activities

CLS A Fully Open-Source Control System

CERN Document Server

Matias, Elder; Johnson, Terry; Tanner, Robby; Wilson, Tony; Wright, Glen; Zhang, Hao

2005-01-01

The Canadian Light Source is one of the first major accelerator facility to adopt a fully open source control system. The control system is based on Experimental Physics and Industrial Control System (EPICS) in use at may other facilities. From the outset CLS utilised RTEMS and Linux as the underlying operating systems for real-time control computers, operator interface computers and servers. When communicating with PLC and other intelligent devices CLS has also adopted a policy of using open communications protocols where possible. Combined these strategies have lead to a system that can easily evolve over the life of the facility without being tied to specific hardware or software suppliers. The operational experience over the past few years has indicates the selected architecture is sufficiently robust and reliable.

A Diagnostic Decision Support System for BMP Selection in Small Urban Watersheds

Science.gov (United States)

Wang, Y.; Montas, H. J.; Leisnham, P.; Shirmohammadi, A.; Brubaker, K. L.; Reiling, S.

2013-12-01

Overall water quality in the United States has improved since the establishment of the Clean Water Act in 1972. While waste water and other point source discharge treatments are expanding and improving in quality, non-point source pollution remains a problem. Best Management Practices (BMPs) are structural and nonstructural methods to mitigate these problems. Much attention has focused on non-point source pollutants in rural areas, where agricultural activities increase the nutrients (fertilizers), toxics (pesticides), and sediments in surface water. Urban and suburban areas also suffer from severe water quantity and quality problems, largely due to stormwater. Low Impact Development (LID), a series of spatially distributed and engineered small-scale hydrologic controls, is an appropriate approach to reduce flow rate and improve urban stormwater quality before it discharges into surface water bodies. This research sought to develop a Diagnostic Decision Support System (DDSS) for urban BMP/LID selection. The process-based hydrologic model, Soil and Water Assessment Tool (SWAT), was used to simulate the hydrologic processes and to estimate related water quality variables. A logic based simple method was developed to identify the critical water quality and quantity hotspots using the SWAT outputs for multiple Hydrologic Response Units (HRUs) within the study watershed. The DDSS consisted of two parts: a Diagnostic Expert System (DES), which identifies the most likely reasons for excessive pollutants; and a Prescriptive Expert System (PES), which selects the best set of spatially distributed BMPs. The DDSS is tested in Watts Branch, a small urban subwatershed in metropolitan Washington D.C. A SWAT model for the watershed was calibrated and validated first. The DDSS was then applied. The final selected series of BMPs was simulated again in the SWAT model for a ten-year period to quantify their effectiveness. The identified hotspots, possible reasons, and BMP solutions

Effective regulatory control of radioactive sources

International Nuclear Information System (INIS)

Meserve, R.A.

2001-01-01

This paper provides an overview of the situation in the USA regarding government control over use of radiation sources, the challenges it faces and the potential paths to their resolution. In the light of the large number of radiation sources in use worldwide, the safety record on balance is remarkably good. But there is still considerable room for improvement. The IAEA has an important role to play, and it is playing it effectively

Model Predictive Control of Z-source Neutral Point Clamped Inverter

DEFF Research Database (Denmark)

Mo, Wei; Loh, Poh Chiang; Blaabjerg, Frede

2011-01-01

This paper presents Model Predictive Control (MPC) of Z-source Neutral Point Clamped (NPC) inverter. For illustration, current control of Z-source NPC grid-connected inverter is analyzed and simulated. With MPC’s advantage of easily including system constraints, load current, impedance network...... response are obtained at the same time with a formulated Z-source NPC inverter network model. Operation steady state and transient state simulation results of MPC are going to be presented, which shows good reference tracking ability of this method. It provides new control method for Z-source NPC inverter...

Control for nuclear thermionic power source

International Nuclear Information System (INIS)

Fletcher, J.C.; Sawyer, C.D.

1978-01-01

A control for a power source is described which includes nuclear fuel interspersed with thermionic converters, including a power regulator that maintains a substantially constant output voltage to a variable load, and a control circuit that drives a neutron flux regulator in accordance with the current supplied to the power regulator and the neutron flux density in the region of the converters. The control circuit generates a control signal which is the difference between the neutron flux density and a linear fucntion of the current, and which drives the neutron regulator in a direction to decrease or increase the neutron flux according to the polarity of the control signal

CLOSED LOOP CONTROL OF EMBEDDED Z-SOURCE INVERTER WITH FUZZY CONTROLLER FOR SOLAR PV APPLICATIONS

OpenAIRE

Midde Mahesh*, K. Leleedhar Rao

2017-01-01

This paper proposes the use of Embedded Z –source inverter system with fuzzy controller for Solar Photo Voltaic (PV) applications with adjustable speed drives. Closed loop operation FUZZY control strategies of EZSI system are proposed. EZSI produces the same voltage gain as Z-source inverter (ZSI) but due to the DC sources embedded within the X- shaped impedance network, it has the added advantage of inherent source filtering capability and also reduced capacitor sizing. This can be achiev...

Control of radioisotopes and radiation sources in Indonesia

International Nuclear Information System (INIS)

Ridwan, M.

2001-01-01

Radioisotopes and radiation sources are extensively used in Indonesia in medicine, industry, mining, agriculture and research. These materials are controlled by the regulatory authority, according to established legal procedures. The Nuclear Energy Control Board of Indonesia (BAPETEN), which was established in 1998 through the Nuclear Energy Act No. 10/1997, is entrusted with the control of any application of nuclear energy, including the application of radioisotopes and radiation sources, through regulation, licensing and inspection. The control is aimed to assure welfare, security and peace, the safety and health of workers and the public, and environmental protection. The number of licences issued to date is around 2400, consisting of 1600 licences for radioisotopes and radiation sources used in hospitals, 347 in radiography, 256 in industry, 53 in mining, and the rest in many other areas such as research and agriculture. A licence can cover one or more radioisotopes or radiation sources, depending on the location of the user institution. These radioisotopes and radiation sources are Co-60, Cs-137, Ir-192, Ra-226, Am-241, Sr-90, Kr-85, Pm-147, linear accelerator and X-ray, and short half-life radioisotopes such as I-125, I-131 and Tc-99m. There are 10 LINACs, 27 X-ray medicines, 61 radioisotope devices for Co-60 and Cs-137, and 10 mHDR Ir-192 for therapeutic purposes currently used in Indonesia and some Ra-226 in storage. Any activity related to the application of nuclear energy is required to be conducted in a manner which observes safety and security. According to the legal requirements, each user has to employ at least one radiation safety officer. To improve the control of the application of radiation sources and radioactive material in the country, BAPETEN introduced some new approaches to the users, including regular dialogues with radiation safety officers and the management of the users, requalification for radiation protection officers twice in five

Orphan sources: Consequences, regaining control and learning the lessons

International Nuclear Information System (INIS)

Croft, J.R.

2001-01-01

The safety and security record of technologies that use radiation sources is adequate in most cases, but on occasions there has been a lack of appropriate controls or circumvention of those that exist, leading to radiological accidents. Particular concern rise those radiation sources that have become orphans i.e. sources that were never subject to regulatory control, or were abandoned, lost or misplaced, stolen, or removed without authorisation. These sources are likely to be found in the public domain; examples include sources that used in radiotherapy units which have been unintentionally sold as scrap metal and melted thereafter, or which have been found by unsuspecting individuals or stolen, causing serious radiation exposure of people and contamination of the human habitat

The regulatory control of radioactive sources in Argentina

International Nuclear Information System (INIS)

Rojkind, Roberto Hector

1997-01-01

Argentina has been conducting nuclear activities for more than forty years, and as early as in 1956 established a Regulatory Authority. Procedures for compliance monitoring and enforcement have been in use in the regulatory control of radioactive sources, and regulatory standards and regulations had been set in Argentina, before the accident in Goiania. The conclusions drawn from that accident encouraged in Argentina the improvement of some regulatory procedures and helped to enhance the quality of the regulatory process. Therefore, the effectiveness of the control of spent radioactive sources has gradually increased, and enforcement actions to prevent radioactive sources ending up in the public domain improved. Some lessons learned in Argentina from the accident in Goiania and the main characteristics of an effective enforcement program helpful to prevent radiological accidents in industrial, medical, research and teaching uses of radioactive sources are presented. (author)

Spatial regulation of bone morphogenetic proteins (BMPs) in postnatal articular and growth plate cartilage

Science.gov (United States)

Garrison, Presley; Yue, Shanna; Hanson, Jeffrey; Baron, Jeffrey; Lui, Julian C.

2017-01-01

Articular and growth plate cartilage both arise from condensations of mesenchymal cells, but ultimately develop important histological and functional differences. Each is composed of three layers—the superficial, mid and deep zones of articular cartilage and the resting, proliferative and hypertrophic zones of growth plate cartilage. The bone morphogenetic protein (BMP) system plays an important role in cartilage development. A gradient in expression of BMP-related genes has been observed across growth plate cartilage, likely playing a role in zonal differentiation. To investigate the presence of a similar expression gradient in articular cartilage, we used laser capture microdissection (LCM) to separate murine growth plate and articular cartilage from the proximal tibia into their six constituent zones, and used a solution hybridization assay with color-coded probes (nCounter) to quantify mRNAs for 30 different BMP-related genes in each zone. In situ hybridization and immunohistochemistry were then used to confirm spatial expression patterns. Expression gradients for Bmp2 and 6 were observed across growth plate cartilage with highest expression in hypertrophic zone. However, intracellular BMP signaling, assessed by phospho-Smad1/5/8 immunohistochemical staining, appeared to be higher in the proliferative zone and prehypertrophic area than in hypertrophic zone, possibly due to high expression of Smad7, an inhibitory Smad, in the hypertrophic zone. We also found BMP expression gradients across the articular cartilage with BMP agonists primarily expressed in the superficial zone and BMP functional antagonists primarily expressed in the deep zone. Phospho-Smad1/5/8 immunohistochemical staining showed a similar gradient. In combination with previous evidence that BMPs regulate chondrocyte proliferation and differentiation, the current findings suggest that BMP signaling gradients exist across both growth plate and articular cartilage and that these gradients may

Effective Regulatory Control of Radioactive Sources in Taiwan

International Nuclear Information System (INIS)

Liu, W.; Yuan, C.; Fan, S.; Su, S.

2004-01-01

Since the incident of radioactively contaminated buildings first surfaced in Taiwan in 1992, efforts have been made by AEC (Atomic Energy Council) of Taiwan to prevent recurrence of similar incidents involving radioactive materials and to achieve effective regulatory control over radioactive sources. The most important milestone is when AEC began to enforce IRPA he Ionizing Radiation Protection Act with the promulgation of 18 relevant regulations on Feb. 1, 2003. In order to enhance accountability of radioactive material and equipment capable of producing ionizing radiation, AEC develops and begins implementing a RPCS Radiation Protection Control System which is a powerful tool in controlling radiation safety and security. In addition, AEC develops a monthly registration program via internet, an o n-line reporting system f or owners/operators of radioactive sources, to improve monitoring of sealed sources (in-use and not-in-use). The registration requirement applies to 469 licensees possessing about 3,000 sealed sources in Taiwan. Because of the threat of orphan sources, AEC has made great efforts in preventing their contamination of construction steel material by establishing and enforcing the RPMMPIRCB Regulation for Preventive Measures and Management Plans for Incident of Radioactively Contaminated Buildings. To comply with this regulation, all 19 of Taiwan's steel factories with melting furnace have installed portal-type radiation detection system to monitor incoming scrap metal. (Author)

The regulatory control of radioactive sources in Argentina

International Nuclear Information System (INIS)

Rojkind, R.H.

1998-01-01

Argentina has been conducting nuclear activities for more than forty years, and had established a Regulatory Authority as early as in 1956. Procedures for compliance monitoring and enforcement have been in use in the regulatory control of radioactive sources, and regulatory standards and regulations were in force in Argentina before the accident in Goiania. The conclusions drawn from the Goiania accident encouraged the Argentine authorities to improve some regulatory procedures and helped to enhance the quality of the regulatory process. As a result, the effectiveness of the control of spent radioactive sources has gradually increased, and enforcement actions to prevent radioactive sources ending up in the public domain have improved. Lessons learned in Argentina from the accident in Goiania are presented as well as the main characteristics of an effective enforcement programme to prevent radiological accidents when radioactive sources are used for industrial, medical, research and teaching purposes. (author)

Regulatory control of radiation sources in Slovakia

International Nuclear Information System (INIS)

Auxtova, L.

2001-01-01

In Slovakia, there are two regulatory authorities. Regulatory control of the utilization of nuclear energy, based on the Slovak National Council's law No. 130/1998 on the peaceful uses of nuclear energy, is exercised by the Nuclear Regulatory Authority of the Slovak Republic. The second regulatory authority - the Ministry of Health - is empowered by law No. 72/1994 on the protection of human health to license radiation sources and is responsible for radiation protection supervision (there are nearly 3000 establishments with sealed sources, radiation generators and unsealed sources in Slovakia). Pursuant to a new radiation protection regulation based on international standards, radiation sources are to be categorized in six classes according to the associated exposure and contamination hazards. A national strategy for improving the safety of radiation sources over their life-cycle and for the management of disused and orphan sources is being prepared for governmental approval. (author)

Regulated control of practices and radiation sources

International Nuclear Information System (INIS)

1992-01-01

Excepting the radiation caused by the natural background radiation, the Executive Secretariat for Nuclear Affairs (SEAN) does not authorize any source no practice within the national territory that may imply exposure of a person to ionizing radiation unless this use is ruled. This document establishes the basic criteria to set up such system as well as to exclude or exempt practices and sources from this regulated control

Effectiveness of best management practices for sediment reduction at operation forest stream crossings

Science.gov (United States)

Laura R. Wear; Michael W. Aust; M. Chad Bolding; Brian D. Strahm; C. Andrew Dolloff

2013-01-01

Temporary skid trail stream crossings have repeatedly been identified as having considerable potential to introduce sediment to streams. Forestry Best Management Practices (BMPs) have proven to be effective for controlling erosion and subsequent sedimentation, yet few studies have quantified sedimentation associated with various levels of BMPs for skidder stream...

Spatio-temporal effects of low impact development practices

Science.gov (United States)

Gilroy, Kristin L.; McCuen, Richard H.

2009-04-01

SummaryThe increase in land development and urbanization experienced in the US and worldwide is causing environmental degradation. Traditional off-site stormwater management does not protect small streams. To mitigate the negative effects of land development, best management practices (BMPs) are being implemented into stormwater management policies for the purposes of controlling minor flooding and improving water quality. Unfortunately, the effectiveness of BMPs has not been extensively studied. The purpose of this research was to analyze the effects of both location and quantity of two types of BMPs: cisterns and bioretention pits. A spatio-temporal model of a microwatershed was developed to determine the effects of BMPs on single-family, townhome, and commercial lots. The effects of development and the BMPs on peak runoff rates and volumes were compared to pre-development conditions. The results show that cisterns alone are capable of controlling rooftop runoff for small storms. Both the spatial location and the volume of BMP storage on a microwatershed influences the effectiveness of BMPs. The volume of BMP storage is positively correlated to the percent reduction in the peak discharge rate and total runoff volume; however, location is a factor in the peak reduction and a maximum volume of effective storage for both hydrologic metrics does exist. These results provide guidelines for developing stormwater management policies that can potentially reduce pollution of first-order streams, lower the cost and maintenance requirements, enhance aesthetics, and increase safety.

The regulatory control of radioactive sources in Argentina

Energy Technology Data Exchange (ETDEWEB)

Rojkind, Roberto Hector [Autoridade Regulatoria Nuclear, Buenos Aires (Argentina)

1997-12-31

Argentina has been conducting nuclear activities for more than forty years, and as early as in 1956 established a Regulatory Authority. Procedures for compliance monitoring and enforcement have been in use in the regulatory control of radioactive sources, and regulatory standards and regulations had been set in Argentina, before the accident in Goiania. The conclusions drawn from that accident encouraged in Argentina the improvement of some regulatory procedures and helped to enhance the quality of the regulatory process. Therefore, the effectiveness of the control of spent radioactive sources has gradually increased, and enforcement actions to prevent radioactive sources ending up in the public domain improved. Some lessons learned in Argentina from the accident in Goiania and the main characteristics of an effective enforcement program helpful to prevent radiological accidents in industrial, medical, research and teaching uses of radioactive sources are presented. (author) 9 refs; e-mail: rrojkind at sede.arn.gov.br

Rate-control algorithms testing by using video source model

DEFF Research Database (Denmark)

Belyaev, Evgeny; Turlikov, Andrey; Ukhanova, Anna

2008-01-01

In this paper the method of rate control algorithms testing by the use of video source model is suggested. The proposed method allows to significantly improve algorithms testing over the big test set.......In this paper the method of rate control algorithms testing by the use of video source model is suggested. The proposed method allows to significantly improve algorithms testing over the big test set....

[Bibliometric analysis of literature regarding integrated schistosomiasis control strategy with emphasis on infectious source control].

Science.gov (United States)

Qian, Yi-Li; Wang, Wei; Hong, Qing-Biao; Liang, You-Sheng

2014-12-01

To evaluate the outcomes of implementation of integrated schistosomiasis control strategy with emphasis on infectious source control using a bibliometric method. The literature pertaining to integrated schistosomiasis control strategy with emphasis on infectious source control was retrieved from CNKI, Wanfangdata, VIP, PubMed, Web of Science, BIOSIS and Google Scholar, and a bibliometric analysis of literature captured was performed. During the period from January 1, 2004 through September 30, 2014, a total of 94 publications regarding integrated schistosomiasis control strategy with emphasis on infectious source control were captured, including 78 Chinese articles (82.98%) and 16 English papers (17.02%). The Chinese literature was published in 21 national journals, and Chinese Journal of Schistosomiasis Control had the largest number of publications, consisting of 37.23% of total publications; 16 English papers were published in 12 international journals, and PLoS Neglected Tropical Diseases had the largest number of publications (3 publications). There were 37 affiliations publishing these 94 articles, and National Institute of Parasitic Diseases, Chinese Center for Disease Control and Prevention (16 publications), Anhui Institute of Schistosomiasis Control (12 publications) and Hunan Institute of Schistosomiasis Control (9 publications) ranked top three affiliations in number of publications. A total of 157 persons were co-authored in these 94 publications, and Wang, Zhou and Zhang ranked top 3 authors in number of publications. The integrated schistosomiasis control strategy with emphasis on infectious source control has been widely implemented in China, and the achievements obtained from the implementation of this strategy should be summarized and transmitted internationally.

National strategies for improving control over orphan sources of ionising radiation

International Nuclear Information System (INIS)

Nizamska, M.

2007-01-01

Since 1989 Bulgaria started reformation of economy sector. Part of this process is the intensive privatisation, as well as in the sited using radioactive materials for different applications - industry, medicine, agriculture, etc. The quick change of property ownership results in difficulties to identify the assessor of radioactive source or material and finally led to appearance of orphan sources. A orphan source is defined as a source that poses sufficient radiological hazard to warrant regulatory control, but which is not under regulatory control because it has never been so, or because it has been abandoned, lost, misplaced, stolen or otherwise transferred without proper authorisation. A face on these problems, Bulgaria is performing a series of measure to improve the control over orphan sources and to strengthening the control over the nuclear and radioactive materials. The report presents briefly this measures. (author)

Femtosecond Light Source for Phase-Controlled Multiphoton Ionization

International Nuclear Information System (INIS)

Sokolov, A. V.; Walker, D. R.; Yavuz, D. D.; Yin, G. Y.; Harris, S. E.

2001-01-01

We describe a femtosecond Raman light source with more than an octave of optical bandwidth. We use this source to demonstrate phase control of multiphoton ionization under conditions where ionization requires eleven photons of the lowest frequency of the spectrum or five photons of the highest frequency. The nonlinearity of the photoionization process allows us to characterize the light source. Experiment-to-theory comparison implies generation of a near single-cycle waveform

Field Operations and Enforcement Manual for Air Pollution Control. Volume II: Control Technology and General Source Inspection.

Science.gov (United States)

Weisburd, Melvin I.

The Field Operations and Enforcement Manual for Air Pollution Control, Volume II, explains in detail the following: technology of source control, modification of operations, particulate control equipment, sulfur dioxide removal systems for power plants, and control equipment for gases and vapors; inspection procedures for general sources, fuel…

A Modified Droop Control Method for Parallel-Connected Current Source Inverters

DEFF Research Database (Denmark)

Wei, Baoze; Guerrero, Josep M.; Quintero, Juan Carlos Vasquez

2016-01-01

In this paper, a novel control method was proposed for current source inverters under the grid-connected working mode. The control scheme is based on a modified droop control method, with an additional current reference signal that will be generated instead of the voltage reference. Hence......, there is only a current control loop with droop control in the whole control scheme without voltage control loop. So it is very suitable for grid-connected current source inverter which will simplify the design of the control scheme and combine the advantage of droop control. The parallel configuration...... is widely used to acquire high power demand, but the circulating current problem is a key issue that should be considered. In this paper, a simulation based on parallel current source inverters using the proposed control scheme is provided. Simulation results showed that a good circulating current...

238Pu sources for cardiac pacemakers. II. Control

International Nuclear Information System (INIS)

Pottier, R.; Merigot, S.

1976-01-01

The method and the apparatus used for thermal (power) and radioactive control of radioisotopic sources for pacemakers are briefly described. The cybernetic system is also presented, which assumes almost automatically the monitoring of control, mechanical and electronic works, data processing, the measurements and computations, and the works related to quality control [fr

Generalized space vector control for current source inverters and rectifiers

Directory of Open Access Journals (Sweden)

Roseline J. Anitha

2016-06-01

Full Text Available Current source inverters (CSI is one of the widely used converter topology in medium voltage drive applications due to its simplicity, motor friendly waveforms and reliable short circuit protection. The current source inverters are usually fed by controlled current source rectifiers (CSR with a large inductor to provide a constant supply current. A generalized control applicable for both CSI and CSR and their extension namely current source multilevel inverters (CSMLI are dealt in this paper. As space vector pulse width modulation (SVPWM features the advantages of flexible control, faster dynamic response, better DC utilization and easy digital implementation it is considered for this work. This paper generalizes SVPWM that could be applied for CSI, CSR and CSMLI. The intense computation involved in framing a generalized space vector control are discussed in detail. The algorithm includes determination of band, region, subregions and vectors. The algorithm is validated by simulation using MATLAB /SIMULINK for CSR 5, 7, 13 level CSMLI and for CSR fed CSI.

Optimization and control of a small angle ion source using an adaptive neural network controller

Energy Technology Data Exchange (ETDEWEB)

Brown, S.K.; Mead, W.C.; Bowling, P.S.; Jones, R.D.; Barnes, C.W.

1993-09-01

This project developed an automated controller based on an artificial neural network and evaluated its applicability in a real-time environment. This capability was developed within the context of a small angle negative ion source on the Discharge Test Stand at Los Alamos. The controller processes information obtained from the beam current waveform, developing a figure of merit (fom) to determine the ion source operating conditions. The fom is composed of the magnitude of the beam current, the stability of operation, and the quietness of the beam. Using no knowledge of operating conditions, the controller begins by making of rough scan of the four-dimensional operating surface. This surface uses as independent variables the anode and cathode temperatures, the hydrogen flow rate, and the arc voltage. `Me dependent variable is the fom described above. Once the rough approximation of the surface has been determined, the network formulates a model from which it determines the best operating point. The controller takes the ion source to that operating point for a reality check. As real data is fed in, the model of the operating surface is updated until the neural network`s model agrees with reality. The controller then uses a gradient ascent method to optimize the operation of the ion source. Initial tests of the controller indicate that it is remarkably capable. It has optimized the operation of the ion source on six different occasions bringing the beam to excellent quality and stability.

Regulatory control of radiation sources in the Philippines

Energy Technology Data Exchange (ETDEWEB)

Daroy, Rosita R

1996-12-31

This paper is concerned with the radiation protection and safety infrastructure providing emphasis on the regulation and control of radiation sources in the Philippines. It deals with the experiences of the Philippine Nuclear Research Institute, as a regulatory body, in the regulation and control of radioactive materials in radiotherapy, nuclear medicine, industrial radiography, industrial gauges, industrial irradiators, and well logging. This paper includes an inventory of the sources and types of devices/equipment used by licensed users of radioactive materials in the Philippines as a contribution to the data base being prepared by the IAEA. The problems encountered by the regulatory body in the licensing and enforcement process, as well as the lessons learned from incidents involving radioactive materials are discussed. Plans for improving compliance to the regulations and enhancing the effectiveness of PNRI`s regulatory functions are presented. (author). Paper presented during the IAEA Regional (RCA) Workshop on System of Notification, Registration, Licensing, and Control of Radiation Sources and Installations, Jakarta, Indonesia, 24-28 April 1995. 6 refs., 2 figs., 12 tabs.

Computer aided control of the Bonn Penning polarized ion source

International Nuclear Information System (INIS)

He, N.W.; VonRossen, P.; Eversheim, P.D.; Busch, R.

1984-01-01

A CBM computer system is described which has been set up to control the Bonn Polarized Ion Source. The controlling program, besides setting and logging parameters, performs an optimization of the ion source output. A free definable figure of merit, being composed of the current of the ionizer and its variance, has proven to be an effective means in directing the source optimization. The performance that has been reached during the first successful tests is reported

A new R-SWAT Decision Making Framework for the Efficient Allocation of Best Management Practices

OpenAIRE

UDIAS MOINELO ANGEL; MALAGO ANNA; REYNAUD ARNAUD; PASTORI MARCO; VIGIAK OLGA; BOURAOUI Faycal

2015-01-01

The work presents and illustrates the application of R-SWAT-DM, a new R framework designed for Decision Making (DM), related to the implementation of Best Management Practices (BMPs), for restoring and protecting the good ecological status of freshwater bodies. R-SWAT-DM combines the use of the SWAT watershed model, the spatial representation of BMPs and an economic component. The SWAT model served as the nonpoint source pollution estimator for current conditions (base line) as well as for sc...

Knowledge based expert system to minimise environmental pollution in Malaysian construction sites

Energy Technology Data Exchange (ETDEWEB)

Al-Hadu, Ibrahiem Abdul Razak; Sidek, Lariyah Mohd; Desa, Mohamad Nor Mohamad [Civil Engineering, Universiti Tenaga Nasional, Kajang, Selangor (Malaysia); Basri, Noor Ezlin Ahmad [Civil Engineering, Universiti Tenaga Nasional, Kajang, Selangor (Malaysia)

2011-07-01

Construction activities generate enormous amount of erosion and sediments sediments that is the result of soil disturbance during construction activities, thus, will pollute the adjacent water bodies and make it unfeasible for different uses. This paper aimed to develop and create the main features of an expert system prototype (ESCES) for minimising erosion and sedimentation due to stormwater generated from the construction activities by recommending a feasible BMPs. Multi criteria Analysis (MCA) technique has been integrated so as to select the best control measure among many stormwater control alternatives. A questionnaire has been distributed to the relevant experts so as to rank the stormwater control measures to be used in the MCA technique. Using Visual Basic 6, Graphical User Interfaces (GUIs) were developed. The knowledge and experience were acquired from various textural sources (i.e. guidelines, manuals, literature, and human expert). Results from this study showed that the Best Management Practices (BMPs) reommended have good suited the site characteristics. As a conclusion from this study, the ESCES can be considered as part of the 'Green Technology Tool' since it helps in protecting the environment and preserve good quality of water adjacent to the construction sites in Malaysia.

Study on upgrade on nuclear control related open source information website

International Nuclear Information System (INIS)

Kim, H. T.; Park, S. S.; Park, W. S.; Choi, Y. M.

2002-01-01

The open source information relevant to the nuclear control is regularly collected, analyzed, and published to the three web sites by the Technology Center for Nuclear Control (TCNC) of the Korea Atomic Energy Research Institute (KAERI). These web sites are world-wide, KAERI-wide, and TCNC-wide, respectively. We are to upgrade the KAERI-wide website to the access-controlled world-wide web site with some additional functionality. In this research, the current status of the three nuclear control related open source information websites managed by the TCNC was introduced and methods for upgrading the KAERI-wide open source information website and associated information security technology were reviewed

Energy control of supercapacitor/fuel cell hybrid power source

International Nuclear Information System (INIS)

Payman, Alireza; Pierfederici, Serge; Meibody-Tabar, Farid

2008-01-01

This paper deals with a flatness based control principle in a hybrid system utilizing a fuel cell as a main power source and a supercapacitor as an auxiliary power source. The control strategy is based on regulation of the dc bus capacitor energy and, consequently, voltage regulation. The proposed control algorithm does not use a commutation algorithm when the operating mode changes with the load power variation and, thus, avoids chattering effects. Using the flatness based control method, the fuel cell dynamic and its delivered power is perfectly controlled, and the fuel cell can operate in a safe condition. In the hybrid system, the supercapacitor functions during transient energy delivery or during energy recovery situations. To validate the proposed method, the control algorithms are executed in dSPACE hardware, while analogical current loops regulators are employed in the experimental environment. The experimental results prove the validity of the proposed approach

Effects of distributed and centralized stormwater best management practices and land cover on urban stream hydrology at the catchment scale

Science.gov (United States)

Loperfido, J. V.; Noe, Gregory B.; Jarnagin, S. Taylor; Hogan, Dianna M.

2014-11-01

Urban stormwater runoff remains an important issue that causes local and regional-scale water quantity and quality issues. Stormwater best management practices (BMPs) have been widely used to mitigate runoff issues, traditionally in a centralized manner; however, problems associated with urban hydrology have remained. An emerging trend is implementation of BMPs in a distributed manner (multi-BMP treatment trains located on the landscape and integrated with urban design), but little catchment-scale performance of these systems have been reported to date. Here, stream hydrologic data (March, 2011-September, 2012) are evaluated in four catchments located in the Chesapeake Bay watershed: one utilizing distributed stormwater BMPs, two utilizing centralized stormwater BMPs, and a forested catchment serving as a reference. Among urban catchments with similar land cover, geology and BMP design standards (i.e. 100-year event), but contrasting placement of stormwater BMPs, distributed BMPs resulted in: significantly greater estimated baseflow, a higher minimum precipitation threshold for stream response and maximum discharge increases, better maximum discharge control for small precipitation events, and reduced runoff volume during an extreme (1000-year) precipitation event compared to centralized BMPs. For all catchments, greater forest land cover and less impervious cover appeared to be more important drivers than stormwater BMP spatial pattern, and caused lower total, stormflow, and baseflow runoff volume; lower maximum discharge during typical precipitation events; and lower runoff volume during an extreme precipitation event. Analysis of hydrologic field data in this study suggests that both the spatial distribution of stormwater BMPs and land cover are important for management of urban stormwater runoff. In particular, catchment-wide application of distributed BMPs improved stream hydrology compared to centralized BMPs, but not enough to fully replicate forested

Effects of distributed and centralized stormwater best management practices and land cover on urban stream hydrology at the catchment scale

Science.gov (United States)

Loperfido, John V.; Noe, Gregory B.; Jarnagin, S. Taylor; Hogan, Dianna M.

2014-01-01

Urban stormwater runoff remains an important issue that causes local and regional-scale water quantity and quality issues. Stormwater best management practices (BMPs) have been widely used to mitigate runoff issues, traditionally in a centralized manner; however, problems associated with urban hydrology have remained. An emerging trend is implementation of BMPs in a distributed manner (multi-BMP treatment trains located on the landscape and integrated with urban design), but little catchment-scale performance of these systems have been reported to date. Here, stream hydrologic data (March, 2011–September, 2012) are evaluated in four catchments located in the Chesapeake Bay watershed: one utilizing distributed stormwater BMPs, two utilizing centralized stormwater BMPs, and a forested catchment serving as a reference. Among urban catchments with similar land cover, geology and BMP design standards (i.e. 100-year event), but contrasting placement of stormwater BMPs, distributed BMPs resulted in: significantly greater estimated baseflow, a higher minimum precipitation threshold for stream response and maximum discharge increases, better maximum discharge control for small precipitation events, and reduced runoff volume during an extreme (1000-year) precipitation event compared to centralized BMPs. For all catchments, greater forest land cover and less impervious cover appeared to be more important drivers than stormwater BMP spatial pattern, and caused lower total, stormflow, and baseflow runoff volume; lower maximum discharge during typical precipitation events; and lower runoff volume during an extreme precipitation event. Analysis of hydrologic field data in this study suggests that both the spatial distribution of stormwater BMPs and land cover are important for management of urban stormwater runoff. In particular, catchment-wide application of distributed BMPs improved stream hydrology compared to centralized BMPs, but not enough to fully replicate forested

Strengthening the control on radioactive sources - Cernavoda NPP operating experience

International Nuclear Information System (INIS)

Daian, I.; Simionov, V.

2005-01-01

This paper presents the national legal frame governing the radioactive source management, legislative requirements introduced during last years and current status of controlled radioactive sources program at Cernavoda NPP. Romania has only one nuclear power plant, Cernavoda NPP, equipped with five PHWR - CANDU-6 Canadian type reactors - with a 700 MW(e) gross capacity each, in different implementation stages. The legal representative of the nuclear power production sector in Romania is 'Nuclearelectrica' S.A. National Company (SNN). SNN is a governmental company controlled by the Ministry of Industry and Trade. The company has headquarters in Bucharest and three subsidiaries: - CNE-PROD Cernavoda (CNE-PROD), operating the Cernavoda NPP - Unit 1; - CNE-INVEST Cernavoda, in charge with the completion of Unit 2 and with the preservation of Units 3,4,5; - Nuclear Fuel Plant in Pitesti (FCN). Unit 1 is in commercial operation since December 2, 1996, Unit 2 is under construction (80% completed) and Units 3, 4, 5 are under preservation. The operation of Cernavoda NPP implies use of radioactive sources that may present a significant risk to health, property and the environment when control is lost. Within the last years CNCAN issued new regulations stating clear responsibilities for the different institutions involved in radioactive materials control programs. To manage radioactive sources in a safe way CNE-PROD established and revised the Controlled Radioactive Sources Program, as part of Station Radiation Protection Regulation, ensuring strict recording of the radioactive sources and their usage, ensuring physical and radiological security, protecting the personnel, members of the public and the environment from the hazards of ionizing radiation during the life cycle of the plant, including decommissioning. (authors)

Strengthening the control on radioactive sources - Cernavoda NPP operating experience

International Nuclear Information System (INIS)

Daian, I.; Simionov, V.

2005-01-01

Full text: This paper presents the national legal frame governing the radioactive source management, legislative requirements introduced during last years and current status of controlled radioactive sources program at Cernavoda NPP. Romania has only one nuclear power plant, Cernavoda NPP, equipped with five PHWR - CANDU-6 Canadian type reactors - with a 700 MW(e) gross capacity each, in different implementation stages. The legal representative of the nuclear power production sector in Romania is 'Nuclearelectrica' S.A. National Company (SNN). SNN is a governmental company controlled by the Ministry of Industry and Trade. The company has headquarters in Bucharest and three subsidiaries: - CNE-PROD Cernavoda (CNE-PROD), operating the Cernavoda NPP - Unit 1; - CNE-INVEST Cernavoda, in charge with the completion of Unit 2 and with the preservation of Units 3,4,5; - Nuclear Fuel Plant in Pitesti (FCN). Unit 1 is in commercial operation since December 2, 1996, Unit 2 is under construction (80% completed) and Units 3, 4, 5 are under preservation. The operation of Cernavoda NPP implies use of radioactive sources that may present a significant risk to health, property and the environment when control is lost. Within the last years CNCAN issued new regulations stating clear responsibilities for the different institutions involved in radioactive materials control programs. To manage radioactive sources in a safe way CNE-PROD established and revised the Controlled Radioactive Sources Program, as part of Station Radiation Protection Regulation, ensuring strict recording of the radioactive sources and their usage, ensuring physical and radiological security, protecting the personnel, members of the public and the environment from the hazards of ionizing radiation during the life cycle of the plant. (authors)

An optical system for controlling ion source parameters

International Nuclear Information System (INIS)

Zhang Baifang; Liu Zhenhao; Jiang Yi; Xu Zhengjia

1999-01-01

An optical control system used for adjusting the source's parameters of an ion separator is described. There are two slice microcomputers at HV terminal and the ground respectively. These microcomputers communicate each other with the full-duplex mode through two pieces of optical fiber, in which many parameters are time-share transmitted in the form of optical pulse. This system can stabilize the arc current and temperature, adjust and display all parameters and has safe-guard ability. At HV terminal, the optical coupling technique is used for connecting the CPU and the ion source, and at the ground the CPU can communicate with a control microcomputer

Implementation and performance evaluation open-source controller for precision control of gripper

Science.gov (United States)

Lee, Seung-Yong; Ham, Un-Hyeong; Park, Young-Woo; Jung, Hak-Sang; Jung, Il-Kyun; Lim, Sun

2017-12-01

This paper proposes integrating gripper embedded operating system, which consist of external interface structure for sophisticated gripper control. This system has multiple functions that control the gripping module and measure the pose of the gripper body with respect to contact environment. A controller based on open source only for the gripper is developed and an external communication interface between robot controller and gripper controller is designed. An experimental environment for the fixed-cycle test consists of integrating magic gripper software system and hardware on commercial business. As a result, a deviation is measured approximately 2% and the system were verified for gripper control.

Development of Remote Control and Interlock System for the PEFP Microwave Ion Source

International Nuclear Information System (INIS)

Song, Young Gi; Seol, Kyung Tae; Kwon, Hyeok Jung; Jang, Ji Ho; Cho, Yong Sub

2011-01-01

The control system for a microwave ion source as an isolated high voltage device is a main part of the PEFP distributed control system. The system is used to control two sets of microwave ion sources, the remote control and the interlock system. A VME system with an embedded Power PC CPU is used as main computer. The VME system is dedicated to control and monitoring of the ion source operation. An isolated control system has been designed and developed for remote control and monitoring of a microwave generator and various power supplies. As the source is placed on high voltage platform, optical fiber isolation has been used between the serial to optical fiber VME I/O board and the control system on the high voltage platform. These are connected through RS232 serial interface. A fast Ethernet is used to communicate between the microwave ion source control system and other control stations in the PEFP control system. EPICS toolkit is adopted to provide network programming and user interface by using EPICS Channel Access (CA)

Assessing the impacts of Best Management Practices on nitrate pollution in an agricultural dominated lowland catchment considering environmental protection versus economic development.

Science.gov (United States)

Haas, Marcelo B; Guse, Björn; Fohrer, Nicola

2017-07-01

Water quality is strongly affected by nitrate inputs in agricultural catchments. Best Management Practices (BMPs) are alternative practices aiming to mitigate the impacts derived from agricultural activities and to improve water quality. Management activities are influenced by different governmental policies like the Water Framework Directive (WFD) and the Renewable Energy Sources Act (EEG). Their distinct goals can be contrasting and hamper an integrated sustainable development. Both need to be addressed in the actual conjuncture in rural areas. Ecohydrological models like the SWAT model are important tools for land cover and land use changes investigation and the assessment of BMPs implementation effects on water quality. Thus, in this study, buffer strip, fertilization reduction and alternative crops were considered as BMPs and were implemented in the SWAT model for the Treene catchment. Their efficiency in terms of nitrate loads reduction related to implementation costs at the catchment scale was investigated. The practices correspond to the catchment conditions and are based on small and mid areal changes. Furthermore, the BMPs were evaluated from the perspective of ecologic and economic policies. The results evidenced different responses of the BMPs. The critical periods in winter were addressed by most of the BMPs. However, some practices like pasture land increase need to be implemented in greater area for better results in comparison to current activities. Furthermore, there is a greater nitrate reduction potential by combining BMPs containing fertilization reduction, buffer strips and soil coverage in winter. The discussion about efficiency showed the complexity of costs stipulation and the relation with arable land and yield losses. Furthermore, as the government policies can be divergent an integrated approach considering all the involved actors is important and seeks a sustainable development. Copyright © 2017 Elsevier Ltd. All rights reserved.

The advanced light source control system

International Nuclear Information System (INIS)

Magyary, S.; Chin, M.; Cork, C.; Fahmie, M.; Lancaster, H.; Molinari, P.; Ritchie, A.; Robb, A.; Timossi, C.; Young, J.

1990-01-01

The criteria for the design of a modern control system are discussed in the context of the special requirements for the control of the Advanced Light Source (ALS). This is followed by the description of the system being built, which has a number of special features. The emphasis has been placed on providing an extremely wide I/O and CPU bandwidth (greater than 120 Mbits/s and 1200 Mips, respectively) and on using commercially available hardware and software. The only major custom design item is the Intelligent Local Controller (ILC), of which about 600 will be used to interface to the hardware. The use of personal computers for the operator stations allows the use of a wealth of industrial standards for windows, languages and tools. (orig.)

Reducing surface water pollution through the assessment of the cost-effectiveness of BMPs at different spatial scales.

Science.gov (United States)

Panagopoulos, Y; Makropoulos, C; Mimikou, M

2011-10-01

Two kinds of agricultural Best Management Practices (BMPs) were examined with respect to cost-effectiveness (CE) in reducing sediment, nitrates-nitrogen (NO(3)-N) and total phosphorus (TP) losses to surface waters of the Arachtos catchment in Western Greece. The establishment of filter strips at the edge of fields and a non-structural measure, namely fertilization reduction in alfalfa, combined with contour farming and zero-tillage in corn and reduction of animal numbers in pastureland, were evaluated. The Soil and Water Assessment Tool (SWAT) model was used as the non-point-source (NPS) estimator, while a simple economic component was developed estimating BMP implementation cost as the mean annual expenses needed to undertake and operate the practice for a 5-year period. After each BMP implementation, the ratio of their CE in reducing pollution was calculated for each Hydrologic Response Unit (HRU) separately, for each agricultural land use type entirely and for the whole catchment. The results at the HRU scale are presented comprehensively on a map, demonstrating the spatial differentiation of CE ratios across the catchment that enhances the identification of locations where each BMP is most advisable for implementation. Based on the analysis, a catchment management solution of affordable total cost would include the expensive measure of filter strips in corn and only in a small number of pastureland fields, in combination with the profitable measure of reducing fertilization to alfalfa fields. When examined for its impact on river loads at the outlet, the latter measure led to a 20 tn or 8% annual decrease of TP from the baseline with savings of 15€/kg of pollutant reduction. Filter strips in corn fields reduced annual sediments by 66 Ktn or 5%, NO(3)-N by 71 tn or 9.5% and TP by 27 tn or 10%, with an additional cost of 3.1 €/tn, 3.3 €/kg and 8.1 €/kg of each pollutant respectively. The study concludes that considerable reductions of several

Revised accident source terms and control room habitability

International Nuclear Information System (INIS)

Lahti, G.P.; Hubner, R.S.; Johnson, W.J.; Schwartz, B.C.

1993-01-01

In April 1992, the NRC staff presented to the Commissioners the draft NUREG open-quotes Revised Accident Source Terms for Light-Water Nuclear Power Plants.close quotes This document is the culmination of more than ten years of NRC-sponsored research and represents the first change in the NRC's position on source terms since TID-14844 was issued in 1962. The purpose of this paper is to investigate the impact of the revised source terms on the current approach to analyzing control room habitability as required by 10 CFR 50. Sample calculations are presented that identify aspects of the model requiring clarification before the implementation of the revised source terms. 6 refs., 4 tabs

Using the soil and water assessment tool to estimate achievable water quality targets through implementation of beneficial management practices in an agricultural watershed.

Science.gov (United States)

Yang, Qi; Benoy, Glenn A; Chow, Thien Lien; Daigle, Jean-Louis; Bourque, Charles P-A; Meng, Fan-Rui

2012-01-01

Runoff from crop production in agricultural watersheds can cause widespread soil loss and degradation of surface water quality. Beneficial management practices (BMPs) for soil conservation are often implemented as remedial measures because BMPs can reduce soil erosion and improve water quality. However, the efficacy of BMPs may be unknown because it can be affected by many factors, such as farming practices, land-use, soil type, topography, and climatic conditions. As such, it is difficult to estimate the impacts of BMPs on water quality through field experiments alone. In this research, the Soil and Water Assessment Tool was used to estimate achievable performance targets of water quality indicators (sediment and soluble P loadings) after implementation of combinations of selected BMPs in the Black Brook Watershed in northwestern New Brunswick, Canada. Four commonly used BMPs (flow diversion terraces [FDTs], fertilizer reductions, tillage methods, and crop rotations), were considered individually and in different combinations. At the watershed level, the best achievable sediment loading was 1.9 t ha(-1) yr(-1) (89% reduction compared with default scenario), with a BMP combination of crop rotation, FDT, and no-till. The best achievable soluble P loading was 0.5 kg ha(-1) yr(-1) (62% reduction), with a BMP combination of crop rotation and FDT and fertilizer reduction. Targets estimated through nonpoint source water quality modeling can be used to evaluate BMP implementation initiatives and provide milestones for the rehabilitation of streams and rivers in agricultural regions. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

A Look at the Future of Controlled-Source Seismology

Science.gov (United States)

Keller, G. R.; Klemperer, S.; Hole, J.; Snelson, C.

2008-12-01

Facilities like EarthScope and IRIS/PASSCAL offer a framework in which to re-assess the role of our highest- resolution geophysical tool, controlled-source seismology. This tool is effective in near surface studies that focus on the upper 100 m of the crust to studies that focus on Moho structure and the lithospheric mantle. IRIS has now existed for over two decades and has transformed the way in which passive-source seismology in particular is carried out. Progress over these two decades has led to major discoveries about continental architecture and evolution through the development of three-dimensional images of the upper mantle and lithosphere. Simultaneously the hydrocarbon exploration industry has mapped increasingly large fractions of our sedimentary basins in three-dimensions and at unprecedented resolution and fidelity. Thanks to the additional instruments in the EarthScope facility, a clear scientific need and opportunity exists to map, at similar resolution, all of the crust - the igneous/metamorphic basement, the non-petroliferous basins that contain the record of continental evolution, and the seismogenic faults and active volcanoes that are the principal natural hazards we face. Controlled-source seismology remains the fundamental technology behind exploration for all fossil fuels and many water resources, and as such is a multi-billion-dollar industry centered in the USA. Academic scientists are leaders in developing the algorithms to process the most advanced industry data, but lack the academic data sets to which to apply this technology. University and government controlled-source seismologists, and their students who will populate the exploration industry, are increasingly divorced from that industry by their reliance on sparse spatial recording of usually only a single-component of the wavefield, generated by even sparser seismic sources. However, if we can find the resources, the technology now exists to provide seismic images of immense

Power Controllability of Three-phase Converter with Unbalanced AC Source

DEFF Research Database (Denmark)

Ma, Ke; Liserre, Marco; Blaabjerg, Frede

2013-01-01

Three-phase DC-AC power converters suffer from power oscillation and overcurrentt problems in case of unbalanced AC source voltage that can be caused by grid/generator faults. Existing solutions to handle these problems are properly selecting and controlling the positive and negative sequence...... currents. In this work a new series of control strategies which utilize the zero-sequence components are proposed to enhance the power control ability under this adverse conditions. It is concluded that by introducing proper zero sequence current controls and corresponding circuit configurations, the power...... converter can enable more flexible control targets, achieving better performances in the delivered power and load current when suffering from unbalanced AC sources....

Modeling generalized interline power-flow controller (GIPFC using 48-pulse voltage source converters

Directory of Open Access Journals (Sweden)

Amir Ghorbani

2018-05-01

Full Text Available Generalized interline power-flow controller (GIPFC is one of the voltage-source controller (VSC-based flexible AC transmission system (FACTS controllers that can independently regulate the power-flow over each transmission line of a multiline system. This paper presents the modeling and performance analysis of GIPFC based on 48-pulsed voltage-source converters. This paper deals with a cascaded multilevel converter model, which is a 48-pulse (three levels voltage source converter. The voltage source converter described in this paper is a harmonic neutralized, 48-pulse GTO converter. The GIPFC controller is based on d-q orthogonal coordinates. The algorithm is verified using simulations in MATLAB/Simulink environment. Comparisons between unified power flow controller (UPFC and GIPFC are also included. Keywords: Generalized interline power-flow controller (GIPFC, Voltage source converter (VCS, 48-pulse GTO converter

Control of orphan sources. Import to and transport through Slovenia

International Nuclear Information System (INIS)

Cesarek, J.; Vokal Nemec, B.

2007-01-01

Orphan sources are radioactive sources which are not under regulatory control, either because they have never been under regulatory control, or because they have been abandoned, lost, misplaced, stolen or transferred without proper authorisation. The issue of orphan sources is not a new one but the situation has been highlighted more and more in the last ten years. One of the most important international milestones in this regard was the conference in Dijon, France in 1998. The orphan sources have become an international problem due to steady increase in international trade which made impossible to control every transfer of goods between countries. Shipments of metal scrap, either national or international, could comprise orphan sources which had come into metal stream. The consequences of such events vary greatly: from contaminated metal just above exemption levels to a melting of volatile radionuclides of significant activity which may cause enormous remediation costs. In addition, the phenomenon of deliberate abuse of nuclear material and radioactive material or previous accidents with found orphan sources worldwide and fatalities have made this issue even more provoking. In Slovenia, no such drastic events have occurred so far. Since 1991 there have been a few meltings of cobalt-60 sources with only economic impact. On several occasions, Italy - the country with strict import control - has detected elevated radiation and denied shipments of scrap metal. They had originated either from Slovenia or from other countries, mostly from former Yugoslav republics. The Slovenian experience shows that majority of cases is related to import of scrap metal in Slovenia or to transit of such material through Slovenia. These orphan sources have originated from past industrial activities or have been under no or weak regulatory control in their countries of origin. In order to prevent inadvertent movement and illicit trafficking of nuclear material and radioactive sources some

A Survey of Open-Source UAV Flight Controllers and Flight Simulators

DEFF Research Database (Denmark)

Ebeid, Emad Samuel Malki; Skriver, Martin; Terkildsen, Kristian Husum

2018-01-01

, which are all tightly linked to the UAV flight controller hardware and software. The lack of standardization of flight controller architectures and the use of proprietary closed-source flight controllers on many UAV platforms, however, complicates this work: solutions developed for one flight controller...... may be difficult to port to another without substantial extra development and testing. Using open-source flight controllers mitigates some of these challenges and enables other researchers to validate and build upon existing research. This paper presents a survey of the publicly available open...

Valuing the Potential Benefits of Water Quality Improvements in Watersheds Affected by Non-Point Source Pollution

Directory of Open Access Journals (Sweden)

Sergio Alvarez

2016-03-01

Full Text Available Nonpoint source (NPS pollution has been identified by the US Environmental Protection Agency (EPA as “the nation’s largest water quality problem”. Urban development, septic systems, and agricultural operations have been identified as the major sources of diffuse pollution in surface and ground water bodies. In recent decades, urban and agricultural Best Management Practices (BMP have been developed in several states to address agricultural water quality and water use impacts, including the reduction of nutrient loads to help meet water quality standards. Compliance with BMPs is associated with some costs to local governments, homeowners, and agricultural operations, but the improvements in water quality associated with BMP adoption are expected to yield significant benefits to society in the form of improved recreational opportunities, navigation, flood control, and ecosystem health. The development of sound policies and decision making processes require balancing the costs of BMP adoption to the agricultural operations with the social benefits to be derived from the improved water quality. In this paper we develop a benefits transfer model to provide estimates of the economic benefits of properly implemented and effective Best Management Practices (BMP throughout the state of Florida. These benefit estimates can be used in a cost-benefit framework to determine the optimal level of BMP adoption throughout the state of Florida and provide a framework for other regions to estimate the potential benefits of BMP-mediated water quality improvements.

Regulatory control and safety of radiation and radioactive sources in Bangladesh

International Nuclear Information System (INIS)

Mollah, A.S.

2001-01-01

The application of ionizing radiation and radioactive sources in different fields such as, medicine, industry, agriculture, research and teaching is constantly increasing in Bangladesh. Any system enacted to control exposure to ionizing radiation has as primary objective the protection of health of people against the deleterious effects of radiation. Establishing the appropriate level of radiological protection and safety of radiation sources used in practice or intervention attains this objective. The regulatory program governing the safe use of radioactive and radiation sources in Bangladesh is based on the legislation enacted as Nuclear Safety and Radiation Control (NSRC) Act-93 and NSRC Rules-97 and its implementation by the competent authority. The radiation control infrastructures and procedure are described as well as their functioning for the implementation of relevant activities such as licensing, regular inspection, personal dose monitoring, emergency preparedness, etc. The issue of security of radiation source is dealt in close relation with the preparation and use of the inventory of all radiation sources in the country

Retrofitting impervious urban infrastructure with green technology for rainfall-runoff restoration, indirect reuse and pollution load reduction.

Science.gov (United States)

Sansalone, John; Raje, Saurabh; Kertesz, Ruben; Maccarone, Kerrilynn; Seltzer, Karl; Siminari, Michele; Simms, Peter; Wood, Brandon

2013-12-01

The built environs alter hydrology and water resource chemistry. Florida is subject to nutrient criteria and is promulgating "no-net-load-increase" criteria for runoff and constituents (nutrients and particulate matter, PM). With such criteria, green infrastructure, hydrologic restoration, indirect reuse and source control are potential design solutions. The study simulates runoff and constituent load control through urban source area re-design to provide long-term "no-net-load-increases". A long-term continuous simulation of pre- and post-development response for an existing surface parking facility is quantified. Retrofits include a biofiltration area reactor (BAR) for hydrologic and denitrification control. A linear infiltration reactor (LIR) of cementitious permeable pavement (CPP) provides infiltration, adsorption and filtration. Pavement cleaning provided source control. Simulation of climate and source area data indicates re-design achieves "no-net-load-increases" at lower costs compared to standard construction. The retrofit system yields lower cost per nutrient load treated compared to Best Management Practices (BMPs). Copyright © 2013 Elsevier Ltd. All rights reserved.

Estimating the gross budget of applied nitrogen and phosphorus in tea plantations

Directory of Open Access Journals (Sweden)

Chi-Feng Chen

2016-05-01

Full Text Available To increase crop yield, high fertilizer application rates have generally been used. The residual fertilizers potentially become a source of diffused pollution, and degrade soil and water quality. Such nonpoint source pollution is a major threat to reservoir eutrophication. The best management practices (BMPs are usually used to prevent eutrophication; however, the environmental distribution of the applied fertilizers has not been understood properly. This could lead to a biased assessment of the rational quantity of nitrogen and phosphorous applied and the selection of BMPs. A field investigation of 32 plantations and 4 forests in the Feitsui Reservoir watershed, Taiwan, was conducted. Storm runoff water and soils were sampled, and a mass balance was used to demonstrate the gross nutrient budget. The results showed that when applying fertilizers of 2700 kg ha−1 in tea plantations only 18.3% of applied nitrogen and 5.5% of applied phosphorus were utilized by tea plants. Less than 5% of applied phosphorus was released in storm runoff, and more than 90% remained in the field. Approximately 30% of the nitrogen was lost through storm runoff, and 52% was stored in the soil mass. Therefore, reducing fertilizer application was recommended as the principal BMP, and collecting and treating storm runoff was suggested for controlling nitrogen pollution. The current management of soil erosion is an efficient measure for controlling phosphorus pollution.

Study on road surface source pollution controlled by permeable pavement

Science.gov (United States)

Zheng, Chaocheng

2018-06-01

The increase of impermeable pavement in urban construction not only increases the runoff of the pavement, but also produces a large number of Non-Point Source Pollution. In the process of controlling road surface runoff by permeable pavement, a large number of particulate matter will be withheld when rainwater is being infiltrated, so as to control the source pollution at the source. In this experiment, we determined the effect of permeable road surface to remove heavy pollutants in the laboratory and discussed the related factors that affect the non-point pollution of permeable pavement, so as to provide a theoretical basis for the application of permeable pavement.

A source-controlled data center network model.

Science.gov (United States)

Yu, Yang; Liang, Mangui; Wang, Zhe

2017-01-01

The construction of data center network by applying SDN technology has become a hot research topic. The SDN architecture has innovatively separated the control plane from the data plane which makes the network more software-oriented and agile. Moreover, it provides virtual multi-tenancy, effective scheduling resources and centralized control strategies to meet the demand for cloud computing data center. However, the explosion of network information is facing severe challenges for SDN controller. The flow storage and lookup mechanisms based on TCAM device have led to the restriction of scalability, high cost and energy consumption. In view of this, a source-controlled data center network (SCDCN) model is proposed herein. The SCDCN model applies a new type of source routing address named the vector address (VA) as the packet-switching label. The VA completely defines the communication path and the data forwarding process can be finished solely relying on VA. There are four advantages in the SCDCN architecture. 1) The model adopts hierarchical multi-controllers and abstracts large-scale data center network into some small network domains that has solved the restriction for the processing ability of single controller and reduced the computational complexity. 2) Vector switches (VS) developed in the core network no longer apply TCAM for table storage and lookup that has significantly cut down the cost and complexity for switches. Meanwhile, the problem of scalability can be solved effectively. 3) The SCDCN model simplifies the establishment process for new flows and there is no need to download flow tables to VS. The amount of control signaling consumed when establishing new flows can be significantly decreased. 4) We design the VS on the NetFPGA platform. The statistical results show that the hardware resource consumption in a VS is about 27% of that in an OFS.

A source-controlled data center network model

Science.gov (United States)

Yu, Yang; Liang, Mangui; Wang, Zhe

2017-01-01

The construction of data center network by applying SDN technology has become a hot research topic. The SDN architecture has innovatively separated the control plane from the data plane which makes the network more software-oriented and agile. Moreover, it provides virtual multi-tenancy, effective scheduling resources and centralized control strategies to meet the demand for cloud computing data center. However, the explosion of network information is facing severe challenges for SDN controller. The flow storage and lookup mechanisms based on TCAM device have led to the restriction of scalability, high cost and energy consumption. In view of this, a source-controlled data center network (SCDCN) model is proposed herein. The SCDCN model applies a new type of source routing address named the vector address (VA) as the packet-switching label. The VA completely defines the communication path and the data forwarding process can be finished solely relying on VA. There are four advantages in the SCDCN architecture. 1) The model adopts hierarchical multi-controllers and abstracts large-scale data center network into some small network domains that has solved the restriction for the processing ability of single controller and reduced the computational complexity. 2) Vector switches (VS) developed in the core network no longer apply TCAM for table storage and lookup that has significantly cut down the cost and complexity for switches. Meanwhile, the problem of scalability can be solved effectively. 3) The SCDCN model simplifies the establishment process for new flows and there is no need to download flow tables to VS. The amount of control signaling consumed when establishing new flows can be significantly decreased. 4) We design the VS on the NetFPGA platform. The statistical results show that the hardware resource consumption in a VS is about 27% of that in an OFS. PMID:28328925

Operational experience of SST1 NBI control system with prototype Ion source

International Nuclear Information System (INIS)

Patel, V B; Patel, P J; Singh, N P; Tripathi, V; Thakkar, D; Gupta, L N; Prahlad, V; Sharma, S K; Bandyopadyay, M; Chakraborty, A K; Baruah, U K; Mattoo, S K; Patel, G B; Onali, Raja

2010-01-01

This paper presents operational experience of integrated control of the arc-filament and High-voltage power supply of Steady State Tokamak (SST)-1 NBI system using Versa Module Europa (VME) system on prototype Ion source. The control algorithm is implemented on the VxWorks operating system using 'C' language. This paper also describes the operating sequence and controls on power supply system. Discharge and Filament power supplies are controlled in such a way so that necessary discharge current can be available in Ion Source. The discharge current is controlled by manipulating the filament current. Close loop control is implemented on each filament power supply with feedback from Discharge Current to control the overall discharge inside the ion source. Necessary actions for shut OFF and subsequent Turn ON are also taken during breakdowns between the Grids of the ion source. Total numbers of breakdowns are also monitored. Shot is terminated, if the breakdown count is higher than the set value. This control system can be programmed to restart High-voltage power supply within 5mS after breakdown occurs. This control system is capable to handle the all types of dynamics in the system. This paper also presents results of experiment.

Infrastructure of Taiwan photon source control network

International Nuclear Information System (INIS)

Chang, Y.T.; Kuo, C.H.; Cheng, Y.S.; Jenny Chen; Hsu, S.Y.; Wu, C.Y.; Hu, K.H.; Hsu, K.T.

2012-01-01

A reliable, flexible and secure network is essential for the Taiwan Photon Source (TPS) control system which is based upon the EPICS tool-kit framework. Subsystem sub-nets will connect to control system via EPICS based CA gateways for forwarding data and reducing network traffic. Combining cyber security technologies such as fire-wall, NAT and VLAN, control network is isolated to protect IOCs and accelerator components. Network management tools are used to improve network performance. Remote access mechanism will be constructed for maintenance and troubleshooting. The Ethernet is also used as field-bus for instruments such as power supplies. This paper will describe the system architecture for the TPS control network. Cabling topology, redundancy and maintainability are also discussed. (authors)

A quality control program for radiation sources

International Nuclear Information System (INIS)

Almeida, C.E. de; Sibata, C.H.; Cecatti, E.R.; Kawakami, N.S.; Alexandre, A.C.; Chiavegatti Junior, M.

1982-01-01

An extensive quality control program was established covering the following areas: physical parameters of the therapeutical machines, dosimetric standards, preventive maintenance of radiation sources and measuring instruments. A critical evaluation of this program was done after two years (1977-1979) of routine application and the results will be presented. The fluctuation on physical parameters strongly supports the efforts and cost of a quality control program. This program has certainly improved the accuracy required on the delivery of the prescribed dose for radiotherapy treatment. (Author) [pt

Sustainable energy from biomass: Biomethane manufacturing plant location and distribution problem

International Nuclear Information System (INIS)

Wu, Bingqing; Sarker, Bhaba R.; Paudel, Krishna P.

2015-01-01

Highlights: • Optimal strategy to locate biogas reactor and allocating feedstock. • Nonlinear mixed integer programming problem structure. • Real world supply chain of biogas production system. • Considers construction cost, transportation and labor costs. • Novel heuristic improves efficiency to obtain optimal solution. - Abstract: As an environment-friendly and renewable energy source, biomethane plays a significant role in the supply of sustainable energy. To facilitate the decision-making process of where to build a biomethane production system (BMPS) and how to allocate the resources for the BMPS, this paper develops an analytical method to find the solutions to location and allocation problems by minimizing the supply chain cost of the BMPS. The BMPS consists of the local farms for providing feedstock, the hubs for collecting and storing feedstock from farms, and the reactors for producing biomethane from feedstock. A mixed integer nonlinear programming (MINLP) is introduced to model the supply chain by considering building, transportation, and labor costs. An alternative heuristic is proposed to obtain an optimal/sub-optimal solution from the MINLP. The validity of the proposed heuristic is proven by numerical examples that are abstracted from practical scenarios.

Regulatory inspection: a powerful tool to control industrial radioactive sources

International Nuclear Information System (INIS)

Silva, F.C.A. da; Leocadio, J.C.; Ramalho, A.T.

2008-01-01

An important contribution for Brazilian development, especially for the quality control of products, is the use of radiation sources by conventional industries. There are in Brazil roughly 3,000 radioactive sources spread out among 950 industries. The main industrial practices involved are: industrial radiography, industrial irradiators, industrial accelerators, well logging petroleum and nuclear gauges. More than 1,800 Radiation Protection Officers (RPOs) were qualified to work in these practices. The present work presents a brief description of the safety control over industrial radioactive installations performed by the Brazilian Regulatory Authority, i.e. the National Commission of Nuclear Energy (CNEN). This paper also describes the national system for radiation safety inspections, the regulation infrastructure and the national inventory of industrial installations. The inspections are based on specific indicators, and their periodicity depends on the risk and type of installation. The present work discusses some relevant aspects that must be considered during the inspections, in order to make the inspections more efficient in controlling the sources. One of these aspects regards the evaluation of the storage place for the sources, a very important parameter for preventing future risky situations. (author)

APPLICATION OF CONTROLLED SOURCE AUDIO MAGNETOTELLURIC (CSAMT AT GEOTHERMAL

Directory of Open Access Journals (Sweden)

Susilawati S.

2017-04-01

Full Text Available CSAMT or Controlled Source Audio-Magnetotelluric is one of the Geophysics methods to determine the resistivity of rock under earth surface. CSAMT method utilizes artificial stream and injected into the ground, the frequency of artificial sources ranging from 0.1 Hz to 10 kHz, CSAMT data source effect correction is inverted. From the inversion results showed that there is a layer having resistivity values ranged between 2.5 Ω.m – 15 Ω.m, which is interpreted that the layer is clay.

Source-dependent and source-independent controls on plutonium oxidation state and colloid associations in groundwater.

Science.gov (United States)

Buesseler, Ken O; Kaplan, Daniel I; Dai, Minhan; Pike, Steven

2009-03-01

Plutonium (Pu) was characterized for its isotopic composition, oxidation states, and association with colloids in groundwater samples near disposal basins in F-Area of the Savannah River Site and compared to similar samples collected six years earlier. Two sources of Pu were identified, the disposal basins, which contained a 24Pu/l39Pu isotopic signature consistent with weapons grade Pu, and 244Cm, a cocontaminant that is a progenitor radionuclide of 24Pu. 24Pu that originated primarily from 244Cm tended to be appreciably more oxidized (Pu(V/VI)), less associated with colloids (approximately 1 kDa - 0.2 microm), and more mobile than 239Pu, as suggested by our prior studies at this site. This is not evidence of isotope fractionation but rather "source-dependent" controls on 240Pu speciation which are processes that are not at equilibrium, i.e., processes that appear kinetically hindered. There were also "source-independent" controls on 239Pu speciation, which are those processes that follow thermodynamic equilibrium with their surroundings. For example, a groundwater pH increase in one well from 4.1 in 1998 to 6.1 in 2004 resulted in an order of magnitude decrease in groundwater 239Pu concentrations. Similarly, the fraction of 239Pu in the reduced Pu(III/IV) and colloidal forms increased systematically with decreases in redox condition in 2004 vs 1998. This research demonstrates the importance of source-dependent and source-independent controls on Pu speciation which would impact Pu mobility during changes in hydrological, chemical, or biological conditions on both seasonal and decadal time scales, and over short spatial scales. This implies more dynamic shifts in Pu speciation, colloids association, and transport in groundwater than commonly believed.

Effects of the airwave in time-domain marine controlled-source electromagnetics

NARCIS (Netherlands)

Hunziker, J.W.; Slob, E.C.; Mulder, W.

2011-01-01

In marine time-domain controlled-source electromagnetics (CSEM), there are two different acquisition methods: with horizontal sources for fast and simple data acquisition or with vertical sources for minimizing the effects of the airwave. Illustrations of the electric field as a function of space

Modeling diffuse phosphorus emissions to assist in best management practice designing

Science.gov (United States)

Kovacs, Adam; Zessner, Matthias; Honti, Mark; Clement, Adrienne

2010-05-01

-bounded P load values at any arbitrary point within the catchment. Finally, a simple design procedure has been built up to plan BMPs in the catchments and simulate their possible impacts on diffuse P fluxes as well as calculate their approximately costs. Both source and transport controlling measures have been involved into the planning procedure. The model also allows examining the impacts of alterations of fertilizer application, point source emissions as well as the climate change on the river loads. Besides this, a simple optimization algorithm has been developed to select the most effective source areas (real hot spots), which should be targeted by the interventions. The fate model performed well in Hungarian pilot catchments. Using the calibrated and validated model, different management scenarios were worked out and their effects and costs evaluated and compared to each other. The results show that the approach is suitable to effectively design BMP measures at local scale. Combinative application of the source and transport controlling BMPs can result in high P reduction efficiency. Optimization of the interventions can remarkably reduce the area demand of the necessary BMPs, consequently the establishment costs can be decreased. The model can be coupled with a larger scale catchment model to form a "screening and planning" modeling system.

Plasma control for efficient extreme ultra-violet source

International Nuclear Information System (INIS)

Takahashi, Kensaku; Nakajima, Mitsuo; Kawamura, Tohru; Shiho, Makoto; Hotta, Eiki; Horioka, Kazuhiko

2008-01-01

To generate a high efficiency extreme-ultraviolet (EUV) source, effects of plasma shape for controlling radiative plasmas based on xenon capillary discharge are experimentally investigated. The radiation characteristics observed via tapered capillary discharge are compared with those of straight one. From the comparison, the long emission period and different plasma behaviors of tapered capillary discharge are confirmed. This means that control of the plasma geometry is effective for prolonging the EUV emission period. This result also indicates that the plasma shape control seems to have a potential for enhancing the conversion efficiency. (author)

Regulatory control of radiation sources in the Philippines

International Nuclear Information System (INIS)

Daroy, Rosita R.

1995-01-01

This paper is concerned with the radiation protection and safety infrastructure providing emphasis on the regulation and control of radiation sources in the Philippines. It deals with the experiences of the Philippine Nuclear Research Institute, as a regulatory body, in the regulation and control of radioactive materials in radiotherapy, nuclear medicine, industrial radiography, industrial gauges, industrial irradiators, and well logging. This paper includes an inventory of the sources and types of devices/equipment used by licensed users of radioactive materials in the Philippines as a contribution to the data base being prepared by the IAEA. The problems encountered by the regulatory body in the licensing and enforcement process, as well as the lessons learned from incidents involving radioactive materials are discussed. Plans for improving compliance to the regulations and enhancing the effectiveness of PNRI's regulatory functions are presented. (author)

RCT: Module 2.08, Radiological Source Control, Course 8774

Energy Technology Data Exchange (ETDEWEB)

Hillmer, Kurt T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-08-10

radioactive source is material used for its emitted radiation. Sources are sealed or unsealed and are classified as accountable or exempt. Radioactive sources are used for response checks, functional checks, and the calibration of instruments and monitors to traceable standards. To ensure the safety and welfare of all personnel, it is important to maintain control of radioactive sources to minimize the potential for the spread of contamination, unnecessary exposure to personnel, loss or theft, and improper disposal. This course will prepare the student with the skills necessary for RCT qualification by passing quizzes, tests, and the RCT Comprehensive Phase 1, Unit 2 Examination (TEST 27566) and will provide in-the-field skills.

Control of radiation sources in Brazil

International Nuclear Information System (INIS)

Oliveira, Silvia Maria Velasques de; Menezes, Sergio Ferreira; Alves Filho, Aristeu Dacio; Xavier, Ana Maria

1997-01-01

The radiological accident occurred in Goiania, in 1987, brought to light several deficiencies in the conduction of the licensing processes of medical, industrial and research facilities that handle radioisotopes as well as int he control of radioactive sources in Brazil. The objective of this article is to describe some of the technical and administrative measures taken to ensure the adoption of appropriate radiological safety standards throughout the country, thus reducing the incidence of radiological accidents. (author)

Control of trafficking of radioactive sources/substances on European Community eastern border

International Nuclear Information System (INIS)

Lovjagina, Irina; Graveris, Visvaldis

2008-01-01

Full text: Taking into account Latvia geographical location, historical core stones (the dissolution of Soviet Union, join to European Community) and increasing of the international terrorism treats, control fissile and non-fissile radioactive material become one of high priorities. During past 2 years active work and practical exercise with representative from Ministry of Defense, Police, and Custom etc. on control of trafficking of such materials were performed and Operational Manual for Control on Radioactive Materials for Customs and Policy officers is issued. All land borders check points with Russian Federation and Byelorussian, all harbors and airports were equipped with a gamma/ neutrons or gamma control portals. To control unwanted material traffic within the country, as well as to ensure the recycled scrap metal is source-free use of monitoring portals and additional portable detectors in the past years strictly increased. Cases with alarm levels, when gamma dose rate exceeds more than 1.5 times the background level, are subject to reporting and analyzing by Radiation Safety Centre (RDC) experts (24 hours on duty). Consultative phone service for inhabitants is maintained; guidelines and working procedures within Authority and other Institutions involving were developed and implemented. As a result, in 2007 RDC has got 612 reports from the border. In 83% cases this was relevant to the trains, in 17%- to the trucks. Mostly enhanced activity was due to potassium compounds in fertilizers (85%), due to ceramics (4%), abrasives (2.5%), and refractory materials (3%). Controlling scrap metal there were revealed two sources in 2007 - one Sr-90 calibration source and other Cs-137 orphan source (origin unknown). The presence of radioactive sources in scrap in the past 3 years has been represented by Co-60, Cs-137 and Sr-90 sources, parts of statically electricity neutralizers, Ra-226. Several times NORM industries polluted materials were from scrap excluded

[Automatic adjustment control system for DC glow discharge plasma source].

Science.gov (United States)

Wan, Zhen-zhen; Wang, Yong-qing; Li, Xiao-jia; Wang, Hai-zhou; Shi, Ning

2011-03-01

There are three important parameters in the DC glow discharge process, the discharge current, discharge voltage and argon pressure in discharge source. These parameters influence each other during glow discharge process. This paper presents an automatic control system for DC glow discharge plasma source. This system collects and controls discharge voltage automatically by adjusting discharge source pressure while the discharge current is constant in the glow discharge process. The design concept, circuit principle and control program of this automatic control system are described. The accuracy is improved by this automatic control system with the method of reducing the complex operations and manual control errors. This system enhances the control accuracy of glow discharge voltage, and reduces the time to reach discharge voltage stability. The glow discharge voltage stability test results with automatic control system are provided as well, the accuracy with automatic control system is better than 1% FS which is improved from 4% FS by manual control. Time to reach discharge voltage stability has been shortened to within 30 s by automatic control from more than 90 s by manual control. Standard samples like middle-low alloy steel and tin bronze have been tested by this automatic control system. The concentration analysis precision has been significantly improved. The RSDs of all the test result are better than 3.5%. In middle-low alloy steel standard sample, the RSD range of concentration test result of Ti, Co and Mn elements is reduced from 3.0%-4.3% by manual control to 1.7%-2.4% by automatic control, and that for S and Mo is also reduced from 5.2%-5.9% to 3.3%-3.5%. In tin bronze standard sample, the RSD range of Sn, Zn and Al elements is reduced from 2.6%-4.4% to 1.0%-2.4%, and that for Si, Ni and Fe is reduced from 6.6%-13.9% to 2.6%-3.5%. The test data is also shown in this paper.

Licensing authority's control of radiation sources and nuclear materials in Brazil

International Nuclear Information System (INIS)

Binns, D.A.C.

2002-01-01

Full text: The Brazilian Nuclear Energy Commission is the national licensing authority and among its responsibilities is the control of nuclear materials and radiation sources. This control is carried out in three different ways: 1) Control of the import and export of nuclear materials and radiation sources. To be able to import or export any nuclear material or radiation source, the user has to have an explicit permission of the licensing authority. This is controlled by electronic means in which the user has to fill a special form found on the licensing authority's home page, where he has to fill in his name, license number, license number of his radiation protection officer and data of the material to be imported or exported. These data are checked with a data base that contains all the information of the licensed users and qualified personnel before authorization is emitted. The airport authorities have already installed x-ray machines to check all baggages entering or leaving the country. 2) Transport and transfer permit for radiation sources. In order to transport and/or transfer radiations sources and nuclear materials within the country, the user(s) have to submit an application to the licensing authority. The user(s) fill out an application form where he fills in his company's name, licensing I.D., radiation protection officer's name and I.D and identification of the sources involved. These information are checked with the licensing operations data before the operations is permitted. 3) Inspections and radiation monitoring systems. Routine and regulatory inspections are continuously carried out where the user's radiation sources and nuclear materials inventory are checked. Also the physical security and protection of these materials are verified. The installation of monitoring systems is an item that is being discussed with the airport authorities so as to increase the possibilities of detecting any illegal transport of these materials. (author)

Regulatory control of radioactive sources: an international perspective

International Nuclear Information System (INIS)

Flakus, F.N.

1998-01-01

Within its Regular Programme and its Technical Co-operation Programme, the IAEA undertakes a number of activities in support of national efforts aimed at strengthening national infrastructures for the control of radiation sources. The framework of these activities is described. (author)

Controlled-source seismic interferometry with one way wave fields

Science.gov (United States)

van der Neut, J.; Wapenaar, K.; Thorbecke, J. W.

2008-12-01

In Seismic Interferometry we generally cross-correlate registrations at two receiver locations and sum over an array of sources to retrieve a Green's function as if one of the receiver locations hosts a (virtual) source and the other receiver location hosts an actual receiver. One application of this concept is to redatum an area of surface sources to a downhole receiver location, without requiring information about the medium between the sources and receivers, thus providing an effective tool for imaging below complex overburden, which is also known as the Virtual Source method. We demonstrate how elastic wavefield decomposition can be effectively combined with controlled-source Seismic Interferometry to generate virtual sources in a downhole receiver array that radiate only down- or upgoing P- or S-waves with receivers sensing only down- or upgoing P- or S- waves. For this purpose we derive exact Green's matrix representations from a reciprocity theorem for decomposed wavefields. Required is the deployment of multi-component sources at the surface and multi- component receivers in a horizontal borehole. The theory is supported with a synthetic elastic model, where redatumed traces are compared with those of a directly modeled reflection response, generated by placing active sources at the virtual source locations and applying elastic wavefield decomposition on both source and receiver side.

A review on effectiveness of best management practices in improving hydrology and water quality: Needs and opportunities.

Science.gov (United States)

Liu, Yaoze; Engel, Bernard A; Flanagan, Dennis C; Gitau, Margaret W; McMillan, Sara K; Chaubey, Indrajeet

2017-12-01

Best management practices (BMPs) have been widely used to address hydrology and water quality issues in both agricultural and urban areas. Increasing numbers of BMPs have been studied in research projects and implemented in watershed management projects, but a gap remains in quantifying their effectiveness through time. In this paper, we review the current knowledge about BMP efficiencies, which indicates that most empirical studies have focused on short-term efficiencies, while few have explored long-term efficiencies. Most simulation efforts that consider BMPs assume constant performance irrespective of ages of the practices, generally based on anticipated maintenance activities or the expected performance over the life of the BMP(s). However, efficiencies of BMPs likely change over time irrespective of maintenance due to factors such as degradation of structures and accumulation of pollutants. Generally, the impacts of BMPs implemented in water quality protection programs at watershed levels have not been as rapid or large as expected, possibly due to overly high expectations for practice long-term efficiency, with BMPs even being sources of pollutants under some conditions and during some time periods. The review of available datasets reveals that current data are limited regarding both short-term and long-term BMP efficiency. Based on this review, this paper provides suggestions regarding needs and opportunities. Existing practice efficiency data need to be compiled. New data on BMP efficiencies that consider important factors, such as maintenance activities, also need to be collected. Then, the existing and new data need to be analyzed. Further research is needed to create a framework, as well as modeling approaches built on the framework, to simulate changes in BMP efficiencies with time. The research community needs to work together in addressing these needs and opportunities, which will assist decision makers in formulating better decisions regarding BMP

System control for the modulated 252Cf source ''Shuffler''

International Nuclear Information System (INIS)

Stephens, M.M.

1975-06-01

The design and theory of operation of the control chassis for a 252 Cf nondestructive assay system are described. This system repetitively transfers a 252 Cf source from the irradiation region to a shielded position before measuring the delayed neutrons. The design criteria for the system were: rapid movement and precise positioning of the 252 Cf source, precise positioning of the sample, and very accurate timing of the irradiate and count cycles. To achieve these results crystal oscillators were used for timing, and stepping motors were used to position the sample and the source. (U.S.)

Testing of best management practices for controlling highway runoff.

Science.gov (United States)

1993-01-01

In order to obtain the necessary detailed design guidelines for storm water best management practices (BMPs) included in the Virginia Department of Transportation's storm water manual, a field program was initiated in 1991 for testing the pollutant r...

Stormwater Controls for Pollutant Removal on GDOT Right-Of-Way

Science.gov (United States)

2012-04-11

The Georgia Department of Transportation (GDOT) operates a large number of roadside stormwater treatment facilities to contain and treat roadside stormwater runoff. The stormwater best management practices (BMPs) were designed with an emphasis on the...

Cross-Layer Design of Source Rate Control and Congestion Control for Wireless Video Streaming

Directory of Open Access Journals (Sweden)

Peng Zhu

2007-01-01

Full Text Available Cross-layer design has been used in streaming video over the wireless channels to optimize the overall system performance. In this paper, we extend our previous work on joint design of source rate control and congestion control for video streaming over the wired channel, and propose a cross-layer design approach for wireless video streaming. First, we extend the QoS-aware congestion control mechanism (TFRCC proposed in our previous work to the wireless scenario, and provide a detailed discussion about how to enhance the overall performance in terms of rate smoothness and responsiveness of the transport protocol. Then, we extend our previous joint design work to the wireless scenario, and a thorough performance evaluation is conducted to investigate its performance. Simulation results show that by cross-layer design of source rate control at application layer and congestion control at transport layer, and by taking advantage of the MAC layer information, our approach can avoid the throughput degradation caused by wireless link error, and better support the QoS requirements of the application. Thus, the playback quality is significantly improved, while good performance of the transport protocol is still preserved.

Regulatory control for safe usage of ionizing radiation sources in Bangladesh

International Nuclear Information System (INIS)

Mollah, A.S.

2008-01-01

Full text: In Bangladesh, there is a widespread and continuos growth in the use of the ionizing radiation sources both radioactive materials and radiation generating equipment in the field of industry, medicine, agriculture, research, teaching etc. In industry, they are employed in production as well as quality control such as non-destructive testing (radiography), nucleonic gauging, radiotracer techniques and in radiation processing. Medical applications of ionizing radiation include X-ray radiography, X-ray fluoroscopy, CT scan, mammography, nuclear medicine, beam therapy and brachytherapy. Besides radioisotopes are also used for research applications, viz., scattering experiments, tracer studies, etc. In agriculture, the uptake of nutrients by soil, and parts of plants are studied using suitable radionuclides. In all the above applications radioisotopes in two forms namely sealed sources and open sources in different chemical forms are employed with source strengths varying from micro curies to mega curies. The benefits to man from the use of ionizing radiation and sources of radiation are accompanied by risks which may result from exposure of man to ionizing radiation. In order to have an effective control on the use of radiation sources and to ensure radiological safety of the user as well as the public, Government of Bangladesh has promulgated Nuclear Safety and Radiation Control (NSRC) rules 1997 under the NSRC Act 1993. The Bangladesh Atomic Energy commission (BAEC) is the competent authority for formulating rules and regulations for ensuring radiological safety. BAEC is legally responsible for developing and strengthening the necessary radiation protection infrastructure in the country through the effective enforcement and implementation of regulatory requirements, criteria, obligations, guiding, codes etc. in order to save man and the related environment from the deleterious effects of ionizing radiation. In Bangladesh, only those persons who have been

Research on wireless remote control scheme for the water source well of a uranium mine

International Nuclear Information System (INIS)

Wang Yun; Bao Feng

2013-01-01

Traditional wired electrical control method is applicable to simple control for the short-distance industrial equipment, but it is not suitable for the water source well of uranium mines requiring remote control. A kind of wireless remote control system based on high-speed radio modem communication technology was presented for the water source wells of a uranium mine, and the water source wells can be remotely controlled with the system. The component, implementation and characteristics of the control system are introduced. (authors)

The Sources of Air Pollution and Their Control.

Science.gov (United States)

National Air Pollution Control Administration (DHEW), Arlington, VA.

The problems of air pollution and its control are discussed. Major consideration is given the sources of pollution - motor vehicles, industry, power plants, space heating, and refuse disposal. Annual emission levels of five principle pollutants - carbon monoxide, sulfur dioxide, nitrogen oxides, hydrocarbons, and particulate matter - are listed…

The geological controls of geothermal groundwater sources in Lebanon

Energy Technology Data Exchange (ETDEWEB)

Shaban, Amin [National Council for Scientific Research, Remote Sensing Center, Beirut (Lebanon); Khalaf-Keyrouz, Layla [Notre Dame University-Louaize, Zouk Mosbeh (Lebanon)

2013-07-01

Lebanon is a country that is relatively rich in water resources, as compared to its neighboring states in the Middle East. Several water sources are issuing on the surface or subsurface, including nonconventional water sources as the geothermal groundwater. This aspect of water sources exists in Lebanon in several localities, as springs or in deep boreholes. To the present little attention has been given to these resources and their geological setting is still unidentified. The preliminary geological field surveys revealed that they mainly occur in the vicinity of the basalt outcrops. Therefore, understanding their geological controls will help in exploring their origin, and thus giving insights into their economical exploitation. This can be investigated by applying advanced detection techniques, field surveys along with detailed geochemical analysis. This study aims at assessing the geographic distribution of the geothermal water in Lebanon with respect to the different geological settings and controls that govern their hydrogeologic regimes. It will introduce an approach for an integrated water resources management which became of utmost significance for the country.

Modeling in control of the Advanced Light Source

International Nuclear Information System (INIS)

Bengtsson, J.; Forest, E.; Nishimura, H.; Schachinger, L.

1991-05-01

A software system for control of accelerator physics parameters of the Advanced Light Source (ALS) is being designed and implemented at LBL. Some of the parameters we wish to control are tunes, chromaticities, and closed orbit distortions as well as linear lattice distortions and, possibly, amplitude- and momentum-dependent tune shifts. In all our applications, the goal is to allow the user to adjust physics parameters of the machine, instead of turning knobs that control magnets directly. This control will take place via a highly graphical user interface, with both a model appropriate to the application and any correction algorithm running alongside as separate processes. Many of these applications will run on a Unix workstation, separate from the controls system, but communicating with the hardware database via Remote Procedure Calls (RPCs)

The control of radioactive sources in Brazil

International Nuclear Information System (INIS)

Oliveira, S.M.V.; Menezes, C.F.; Alves Filho, A.D.; Xavier, A.M.

1998-01-01

The radiological accident of Goiania in 1987 brought to light several deficiencies in the licensing of medical, industrial and research facilities, which handle radioisotopes, as well as in the control of radioactive sources in Brazil. The article describes some of the technical and administrative measures taken to ensure the adoption of appropriate radiological safety standards throughout the country and thereby reduce the incidence of radiological accidents. (author)

Testing of best management practices for controlling highway runoff, Phase II.

Science.gov (United States)

1994-01-01

In order to obtain the detailed information necessary to develop design guidelines for the stormwater best management practices (BMPs) included in the Virginia Department of Transportation's Stormwater Management Manual, a field program was initiated...

Best Management Practices Monitoring Guide for Stream Systems

OpenAIRE

Mesner, Nancy

2011-01-01

Best Management Practices Monitoring Guide for Stream Systems provides guidance on establishing a water quality monitoring program that will demonstrate the effectiveness of Best Management Practices (BMPs) to reduce nonpoint source pollution in stream systems.

Status report on the ADVANCED LIGHT SOURCE control system

International Nuclear Information System (INIS)

Magyary, S.; Chin, M.; Fahmie, M.; Lancaster, H.; Molinari, P.; Robb, A.; Timossi, C.; Young, J.

1992-01-01

This paper is a status report on the ADVANCED LIGHT SOURCE (ALS) control system. The current status, performance data, and future plans will be discussed. Manpower, scheduling, and costs issues are addressed. (author)

Applying neural networks to control the TFTR neutral beam ion sources

International Nuclear Information System (INIS)

Lagin, L.

1992-01-01

This paper describes the application of neural networks to the control of the neutral beam long-pulse positive ion source accelerators on the Tokamak Fusion Test Reactor (TFTR) at Princeton University. Neural networks were used to learn how the operators adjust the control setpoints when running these sources. The data sets used to train these networks were derived from a large database containing actual setpoints and power supply waveform calculations for the 1990 run period. The networks learned what the optimum control setpoints should initially be set based uon desired accel voltage and perveance levels. Neural networks were also used to predict the divergence of the ion beam

Mobile source pollution control in the United States and China

International Nuclear Information System (INIS)

Menz, Fredric C

2002-01-01

This paper reviews policies for the control of mobile source pollution and their potential application in China. The first section of the paper reviews the U.S. experience with mobile source pollution control since regulations were first established in the Clean Air Act of 1970. Highlights in the policy and trends in vehicle emissions over the 1970 to 2000 time period are discussed. The second section of the paper discusses the range of policy instruments that could be used to control vehicle pollution, ranging from traditional direct regulations to market-based instruments. Experiences with the use of economic incentives in the United States and elsewhere are also discussed. The third section of the paper discusses possible implications of the U.S. experience for controlling vehicle pollution in China. While market-based instruments might be particularly appropriate for use in several aspects of China's pollution control policies, important differences between the institutional structures in China and the United States suggest that they should be phased in gradually. The paper closes with concluding remarks. (author)

Mobile source pollution control in the United States and China

Energy Technology Data Exchange (ETDEWEB)

Menz, Fredric C

2002-07-01

This paper reviews policies for the control of mobile source pollution and their potential application in China. The first section of the paper reviews the U.S. experience with mobile source pollution control since regulations were first established in the Clean Air Act of 1970. Highlights in the policy and trends in vehicle emissions over the 1970 to 2000 time period are discussed. The second section of the paper discusses the range of policy instruments that could be used to control vehicle pollution, ranging from traditional direct regulations to market-based instruments. Experiences with the use of economic incentives in the United States and elsewhere are also discussed. The third section of the paper discusses possible implications of the U.S. experience for controlling vehicle pollution in China. While market-based instruments might be particularly appropriate for use in several aspects of China's pollution control policies, important differences between the institutional structures in China and the United States suggest that they should be phased in gradually. The paper closes with concluding remarks. (author)

Single-crate stand-alone CAMAC control system for a negative ion source test facility

International Nuclear Information System (INIS)

Juras, R.C.; Ziegler, N.F.

1979-01-01

A single-crate CAMAC system was configured to control a negative ion source development facility at ORNL and control software was written for the crate microcomputer. The software uses inputs from a touch panel and a shaft encoder to control the various operating parameters of the test facility and uses the touch panel to display the operating status. Communication to and from the equipment at ion source potential is accomplished over optical fibers from an ORNL-built CAMAC module. A receiver at ion source potential stores the transmitted data and some of these stored values are then used to control discrete parameters of the ion source (i.e., power supply on or off). Other stored values are sent to a multiplexed digital-to-analog converter to provide analog control signals. A transmitter at ion source potential transmits discrete status information and several channels of analog data from an analog-to-digital converter back to the ground-potential receiver where it is stored to be read and displayed by the software

Experimental Physics and Industrial Control System (EPICS): Application source/release control for EPICS R3.11.6

International Nuclear Information System (INIS)

Zieman, B.; Kraimer, M.

1994-01-01

This manual describes a set of tools that can be used to develop software for EPICS based control systems. It provides the following features: Multiple applications; the entire system is composed of an arbitrary number of applications: Source/Release Control; all files created or modified by the applications developers can be put under sccs (a UNIX Source/Release control utility): Multiple Developers; it allows a number of applications developers to work separately during the development phase but combine their applications for system testing and for a production system; Makefiles: makefiles are provided to automatically rebuild various application components. For C and state notation programs, Imagefiles are provided

The IAEA Regional Training Course on Regulatory Control of Radiation Sources

International Nuclear Information System (INIS)

2000-01-01

Materials of the IAEA Regional Training Course contains 8 presented lectures. Authors deals with regulatory control of radiation sources. The next materials of the IAEA were presented: Organization and implementation of a national regulatory infrastructure governing protection against ionizing radiation and the safety of radiation sources. (IAEA-TECDOC-1067); Safety assessment plants for authorization and inspection of radiation sources (IAEA-TECDOC-1113); Regulatory authority information system RAIS, Version 2.0, Instruction manual

Modified source of a fast neutral atom beam with a controlled energy

International Nuclear Information System (INIS)

Gostev, V.A.; Elakhovskij, D.V.; Khakhaev, A.D.

1980-01-01

A source of a metastable helium atom beam with a controlled energy based on a phenomenon of resonant ion neutralization on the surface of a solid body is described. The neutral particle energy control is carried out by changing ion velocities before their transformation into metastable atoms. The results of experiments with a modified construction of atomic beam source are stated. These experiments were conducted to find the possibilities to control velocities of atoms in a flow as well as to elucidate the peculiarities of operation of a collimator-converter of this construction. Dependences of a halfwidth of the ion velocity distribution function on the ion source parameters have been investigated. The possibility for particle energy control in a collimated flow of fast neutral. atoms has been experimentally shown, it is also shown that a mean value of atom energy in a beam coincides with a value of mean energy of ions from which atoms are produced by the resonant neutralization method; the construction of the source provides the possibility to realize the method of ''overtaking beams'' for neutral atoms and as a result of this to give a possibility for studying atom-atom collisions in a wide energy range at relatively high densities of flows

Variable cycle control model for intersection based on multi-source information

Science.gov (United States)

Sun, Zhi-Yuan; Li, Yue; Qu, Wen-Cong; Chen, Yan-Yan

2018-05-01

In order to improve the efficiency of traffic control system in the era of big data, a new variable cycle control model based on multi-source information is presented for intersection in this paper. Firstly, with consideration of multi-source information, a unified framework based on cyber-physical system is proposed. Secondly, taking into account the variable length of cell, hysteresis phenomenon of traffic flow and the characteristics of lane group, a Lane group-based Cell Transmission Model is established to describe the physical properties of traffic flow under different traffic signal control schemes. Thirdly, the variable cycle control problem is abstracted into a bi-level programming model. The upper level model is put forward for cycle length optimization considering traffic capacity and delay. The lower level model is a dynamic signal control decision model based on fairness analysis. Then, a Hybrid Intelligent Optimization Algorithm is raised to solve the proposed model. Finally, a case study shows the efficiency and applicability of the proposed model and algorithm.

REGIONAL DRAINWATER MANAGEMENT: SOURCE CONTROL, AGROFORESTRY, AND EVAPORATION PONDS

OpenAIRE

Posnikoff, Judith F.; Knapp, Keith C.

1996-01-01

Source control is one way to address salinity and drainage problems in irrigated agriculture, and reuse of drainage flows on salt-tolerant crops or trees in agroforestry production is another. A regional model of agricultural production with drainwater reuse and disposal is developed. Deep percolation flows are controlled through choice of crop areas, irrigation systems, and applied-water quantities. Crop drainwater may by reused in agroforestry production, and residual emissions are disposed...

Can There Ever Be Enough to Impact Water Quality? Evaluating BMPs in Elliot Ditch, Indiana Using the LTHIA-LID Model

Science.gov (United States)

Rahman, M. S.; Hoover, F. A.; Bowling, L. C.

2017-12-01

Elliot Ditch is an urban/urbanizing watershed located in the city of Lafayette, IN, USA. The city continues to struggle with stormwater management and combined sewer overflow (CSO) events. Several best-management practices (BMP) such as rain gardens, green roofs, and bioswales have been implemented in the watershed, but the level of adoption needed to achieve meaningful impact is currently unknown. This study's goal is to determine what level of BMP coverage is needed to impact water quality, whether meaningful impact is determined by achieving water quality targets or statistical significance. A power analysis was performed using water quality data for total suspended solids (TSS), E.coli, total phosphorus (TP) and nitrate (NO3-N) from Elliot Ditch from 2011 to 2015. The minimum detectable difference (MDD) was calculated as the percent reduction in load needed to detect a significant change in the watershed. The water quality targets were proposed by stakeholders as part of a watershed management planning process. The water quality targets and the MDD percentages were then compared to simulated load reductions due to BMP implementation using the Long-term Hydrologic Impact Assessment-Low Impact Development (LTHIA-LID) model. Seven baseline model scenarios were simulated by implementing the maximum number of each of six types of BMPs (rain barrels, permeable patios, green roofs, grassed swale/bioswales, bioretention/rain gardens, and porous pavement), as well as all the practices combined in the watershed. These provide the baseline for targeted implementation scenarios designed to determine if statistically and physically meaningful load reductions can be achieved through BMP implementation alone.

Status report on the Advanced Light Source control system, 1993

International Nuclear Information System (INIS)

Young, J.; Brown, W. Jr.; Cork, C.

1993-10-01

The Advanced Light Source (ALS), under construction for the past seven years, has become operational. The accelerator has been successfully commissioned using a control system based on hundreds of controllers of our own design and high performance personal computers which are the operator interface. The first beamlines are being commissioned using a control system based on VME hardware and the Experimental Physics and Industrial Control System (EPICS) software. The two systems are being integrated, and this paper reports on the current work being done

Sealed Radioactive Sources. Information, Resources, and Advice for Key Groups about Preventing the Loss of Control over Sealed Radioactive Sources

International Nuclear Information System (INIS)

2013-10-01

Among its many activities to improve the safety and security of sealed sources, the IAEA has been investigating the root causes of major accidents and incidents since the 1980's and publishes findings so that others can learn from them. There are growing concerns today about the possibility that an improperly stored source could be stolen and used for malicious purposes. To improve both safety and security, information needs to be in the hands of those whose actions and decisions can prevent a source from being lost or stolen in the first place. The IAEA developed this booklet to help improve communication with key groups about hazards that may result from the loss of control over sealed radioactive sources and measures that should be implemented to prevent such loss of control. Many people may benefit from the information contained in this booklet, particularly those working with sources and those likely to be involved if control over a source is lost; especially: officials in government agencies, first responders, medical users, industrial users and the metal recycling industry. The general public may also benefit from an understanding of the fundamentals of radiation safety. This booklet is comprised of several stand-alone chapters intended to communicate with these key groups. Various accidents that are described and information that is provided are relevant to more than one key group and therefore, some information is repeated throughout the booklet. This booklet seeks to raise awareness of the importance of the safety and security of sealed radioactive sources. However, it is not intended to be a comprehensive 'how to' guide for implementing safety and security measures for sealed radioactive sources. For more information on these measures, readers are encouraged to consult the key IAEA safety and security-related publications identified in this booklet

The regulatory control of radiation sources in Australia -- The challenges of a federal system

International Nuclear Information System (INIS)

Loy, J.; Colgan, P.

2001-01-01

The report refers to the challenges that Australia is facing, as a federal nation having a Commonwealth Government and six States and two territories, in establishing appropriate regulatory control of radiation sources. Information on the national inventory of radiation sources and existing regulatory infrastructure, including the system of notification, registration, licensing, inspection and enforcement, is explained in the report. The national provisions for the management of disused sources; the planning, preparedness and response to abnormal events and emergencies; the recovery of control over orphan sources; and education and training; are specifically emphasized. (author)

National Management Measures to Control Nonpoint Source Pollution from Forestry

Science.gov (United States)

This report helps forest owners protect lakes and streams from polluted runoff that can result from forestry activities. The report will also help states to implement their nonpoint source control programs.

Knowledge and use of the internet as a source of controlled substances.

Science.gov (United States)

M Gordon, Susan; Forman, Robert F; Siatkowski, Candis

2006-04-01

Despite growing evidence that the internet is a source of controlled substances for nonmedical use, there is a lack of information about who is using it to obtain these drugs. One hundred adult drug-dependent inpatients in a private residential treatment program participated in a semistructured interview regarding how they obtained their drugs. Twenty-nine percent reported knowledge of the internet as a source of drugs, and 11% reported that they had used the internet to either buy drugs or locate a drug dealer. The results of this preliminary study suggest that the internet has become a source of controlled substances for some addicted individuals. Considerations for future research and clinical practice are described.

A wavenumber approach to analysing the active control of plane waves with arrays of secondary sources

Science.gov (United States)

Elliott, Stephen J.; Cheer, Jordan; Bhan, Lam; Shi, Chuang; Gan, Woon-Seng

2018-04-01

The active control of an incident sound field with an array of secondary sources is a fundamental problem in active control. In this paper the optimal performance of an infinite array of secondary sources in controlling a plane incident sound wave is first considered in free space. An analytic solution for normal incidence plane waves is presented, indicating a clear cut-off frequency for good performance, when the separation distance between the uniformly-spaced sources is equal to a wavelength. The extent of the near field pressure close to the source array is also quantified, since this determines the positions of the error microphones in a practical arrangement. The theory is also extended to oblique incident waves. This result is then compared with numerical simulations of controlling the sound power radiated through an open aperture in a rigid wall, subject to an incident plane wave, using an array of secondary sources in the aperture. In this case the diffraction through the aperture becomes important when its size is compatible with the acoustic wavelength, in which case only a few sources are necessary for good control. When the size of the aperture is large compared to the wavelength, and diffraction is less important but more secondary sources need to be used for good control, the results then become similar to those for the free field problem with an infinite source array.

Regularity of the wear control of radioactive sources from the nuclear measurers

International Nuclear Information System (INIS)

Ferreira L, M.

2006-01-01

The control of radioactive sources in Brazil is regulated by the CNEN (National Comissao of Nuclear Energy). The Laboratory of Descontaminacao of the IPEN (Institute of Energy Y Nuclear Investigations) it offers to the companies that work with nuclear measurers, essays for control of the source wear according to the ISO 9978/1992 through the smear tests Y of leakage. The analyses are taken in alpha Y beta detectors of low bottom radiation with annual detection limits around 1 Bq. Certificates of the accepted analyses by the CNEN for sources that already passed its time of validity assured by the makers, but its continue operational are emitted. The smear test is repeated the whole year, while the leakage test repeats to every two years. A balance of the last two years of the activities of the laboratory shows the regularity of the clients Y the growth of companies specialized in radioprotection with official of radioprotection, credited by the regulatory authority that its act as intermediaries in the process, contacting the clients, gathering the samples next to the proprietors of sources Y hiring our services. Overalls, proves that the inspection activities by part of the regulatory authority are fulfil. In 2004, 192 sources were analyzed by the smear method Y 86 sources by leakage. In 2005, 232 sources were analyzed by the smear method Y 60 sources by leakage. All the leakage tests was made in sources of Americium of oneself Y only client that brings the sources so that they dismantle them to him in the Sources production laboratory of the IPEN. By the quantity Y age of the sources that were analyzed in those two years, it is proven that the number of sources without use conditions (total activity measured by the two added methods smaller than 180Bq) it doesn't arrive to 2%. (Author)

Power Controllability of Three-phase Converter with Unbalanced AC Source

DEFF Research Database (Denmark)

Ma, Ke; Chen, Wenjie; Liserre, Marco

2015-01-01

Three-phase DC-AC power converters suffer from power oscillation and overcurrent problems in case of unbalanced AC source voltage that can be caused by grid/generator faults. Existing solutions to handle these problems are properly selecting and controlling the positive and negative sequence...... currents. In this work a new series of control strategies which utilize the zerosequence components are proposed to enhance the power control ability under this adverse condition. It is concluded that by introducing proper zero sequence current controls and corresponding circuit configurations, the power...... converter can enable more flexible control targets, achieving better performances in the delivered power and load current when suffering from unbalanced AC voltage....

Storage of low-level radioactive waste and regulatory control of sealed sources in Finland

International Nuclear Information System (INIS)

Rahola, T.; Markkanen, M.

2006-01-01

This paper is concentrated on the non nuclear low-level radioactive waste. The cornerstone for maintaining radioactive sources under control in Finland is that all practices involving sources are subject to authorization and all licensing information, including information on each individual source, are entered into a register which is continuously updated based on applications and notifications received from the licenses. Experiences during the past twenty years have shown that source-specific records of sources combined with regular inspections at the places of use have prevented efficiency losing control over sealed radioactive sources. The current capacity in the interim storage for State owned waste is not adequate for all used sealed sources and other small user waste which are currently kept in the possession of the licensees. Thus, expansion of the storage capacity and other options for taking care of the small user waste is under consideration. (N.C.)

Spatial optimization of watershed management practices for nitrogen load reduction using a modeling-optimization framework

Science.gov (United States)

Best management practices (BMPs) are perceived as being effective in reducing nutrient loads transported from non-point sources (NPS) to receiving water bodies. The objective of this study was to develop a modeling-optimization framework that can be used by watershed management p...

Assessment of Runoff and Sediment Yields Using the AnnAGNPS Model from the Daning River Watershed in Three-Gorge Area of China

Science.gov (United States)

Soil erosion has been recognized as one of the major threats to our environment and water quality worldwide, especially in China. To mitigate nonpoint source water quality problems caused by soil erosion, best management practices (BMPs) and/or conservation programs have been ado...

Suburban watershed nitrogen retention: Estimating the effectiveness of stormwater management structures

Science.gov (United States)

Koch, Benjamin J.; Febria, Catherine M.; Cooke, Roger M.; Hosen, Jacob D.; Baker, Matthew E.; Colson, Abigail R.; Filoso, Solange; Hayhoe, Katharine; Loperfido, J. V.; Stoner, Anne M.K.; Palmer, Margaret A.

2015-01-01

Excess nitrogen (N) is a primary driver of freshwater and coastal eutrophication globally, and urban stormwater is a rapidly growing source of N pollution. Stormwater best management practices (BMPs) are used widely to remove excess N from runoff in urban and suburban areas, and are expected to perform under a wide variety of environmental conditions. Yet the capacity of BMPs to retain excess N varies; and both the variation and the drivers thereof are largely unknown, hindering the ability of water resource managers to meet water quality targets in a cost-effective way. Here, we use structured expert judgment (SEJ), a performance-weighted method of expert elicitation, to quantify the uncertainty in BMP performance under a range of site-specific environmental conditions and to estimate the extent to which key environmental factors influence variation in BMP performance. We hypothesized that rain event frequency and magnitude, BMP type and size, and physiographic province would significantly influence the experts’ estimates of N retention by BMPs common to suburban Piedmont and Coastal Plain watersheds of the Chesapeake Bay region.

Enhanced osteogenesis of adipose derived stem cells with Noggin suppression and delivery of BMP-2.

Directory of Open Access Journals (Sweden)

Jiabing Fan

Full Text Available Bone morphogenetic proteins (BMPs are believed to be the most potent osteoinductive factors. However, BMPs are highly pleiotropic molecules and their supra-physiological high dose requirement leads to adverse side effects and inefficient bone formation. Thus, there is a need to develop alternative osteoinductive growth factor strategies that can effectively complement BMP activity. In this study, we intrinsically stimulated BMP signaling in adipose derived stem cells (ASCs by downregulating noggin, a potent BMP antagonist, using an RNAi strategy. ASCs transduced with noggin shRNA significantly enhanced osteogenic differentiation of cells. The potency of endogenous BMPs was subsequently enhanced by stimulating ASCs with exogenous BMPs at a significantly reduced dose. The level of mineralization in noggin shRNA treated ASCs when treated with BMP-2 was comparable to that of control shRNA treated cell treated with 10-fold more BMP-2. The complementary strategy of noggin suppression + BMP-2 to enhance osteogenesis was further confirmed in 3D in vitro environments using scaffolds consisting of chitosan (CH, chondroitin sulfate (CS, and apatite layer on their surfaces designed to slowly release BMP-2. This finding supports the novel therapeutic potential of this complementary strategy in bone regeneration.

Note: Tormenta: An open source Python-powered control software for camera based optical microscopy.

Science.gov (United States)

Barabas, Federico M; Masullo, Luciano A; Stefani, Fernando D

2016-12-01

Until recently, PC control and synchronization of scientific instruments was only possible through closed-source expensive frameworks like National Instruments' LabVIEW. Nowadays, efficient cost-free alternatives are available in the context of a continuously growing community of open-source software developers. Here, we report on Tormenta, a modular open-source software for the control of camera-based optical microscopes. Tormenta is built on Python, works on multiple operating systems, and includes some key features for fluorescence nanoscopy based on single molecule localization.

Regulatory control of radiation sources and radioactive materials in the Czech Republic

International Nuclear Information System (INIS)

Drabova, D.; Prouza, Z.

2001-01-01

The paper describes legal and regulatory provisions for radiation protection and safe use of sources of ionizing radiation in the Czech Republic with special emphasis on aspects of bringing activities under regulatory control and releasing them from it. It covers the development of a new legal framework, the work of the regulatory body, an overview of sources in use and provisions to achieve effective regulatory control of facilities and releases of radioactive material into the environment. Also, it describes reported unusual events with a proposed scheme for their classification and evaluation. (author)

Evaluation of PCB sources and releases for identifying priorities to reduce PCBs in Washington State (USA).

Science.gov (United States)

Davies, Holly; Delistraty, Damon

2016-02-01

Polychlorinated biphenyls (PCBs) are ubiquitously distributed in the environment and produce multiple adverse effects in humans and wildlife. As a result, the purpose of our study was to characterize PCB sources in anthropogenic materials and releases to the environment in Washington State (USA) in order to formulate recommendations to reduce PCB exposures. Methods included review of relevant publications (e.g., open literature, industry studies and reports, federal and state government databases), scaling of PCB sources from national or county estimates to state estimates, and communication with industry associations and private and public utilities. Recognizing high associated uncertainty due to incomplete data, we strived to provide central tendency estimates for PCB sources. In terms of mass (high to low), PCB sources include lamp ballasts, caulk, small capacitors, large capacitors, and transformers. For perspective, these sources (200,000-500,000 kg) overwhelm PCBs estimated to reside in the Puget Sound ecosystem (1500 kg). Annual releases of PCBs to the environment (high to low) are attributed to lamp ballasts (400-1500 kg), inadvertent generation by industrial processes (900 kg), caulk (160 kg), small capacitors (3-150 kg), large capacitors (10-80 kg), pigments and dyes (0.02-31 kg), and transformers (PCB distribution and decrease exposures include assessment of PCBs in buildings (e.g., schools) and replacement of these materials, development of Best Management Practices (BMPs) to contain PCBs, reduction of inadvertent generation of PCBs in consumer products, expansion of environmental monitoring and public education, and research to identify specific PCB congener profiles in human tissues.

Variable speed wind turbine generator system with current controlled voltage source inverter

International Nuclear Information System (INIS)

Muyeen, S.M.; Al-Durra, Ahmed; Tamura, J.

2011-01-01

highlights: → Current controlled voltage source inverter scheme for wind power application. → Low voltage ride through of wind farm. → Variable speed wind turbine driven permanent magnet synchronous generator-operation and control. -- Abstract: The present popular trend of wind power generation is to use variable speed wind turbine (VSWT) driving a doubly fed induction generator (DFIG), wound field synchronous generator (WFSG) or permanent magnet synchronous generator (PMSG). Among them, stability analyses of DFIG type of VSWT have already been reported in many literatures. However, transient stability and low voltage ride through (LVRT) characteristics analyses for synchronous generator type of VSWT is not sufficient enough. This paper focuses on detailed LVRT characteristic analysis of variable speed wind turbine driving a PMSG (VSWT-PMSG) with current controlled voltage source inverter (CC-VSI). Modeling and suitable control strategies for overall system are developed to augment the low voltage ride through capability of variable speed wind generator, considering recent wind farm grid code. Both symmetrical and unsymmetrical faults are analyzed as network disturbances in this paper. The permanent fault due to unsuccessful reclosing of circuit breakers is taken into consideration, which is a salient feature of this study. Moreover, the dynamic characteristic is analyzed using real wind speed data measured in Hokkaido Island, Japan. The proposed control scheme is simulated by using the standard power system simulation package PSCAD/EMTDC and results are verified by comparing that of voltage controlled voltage source inverter scheme available in power system literature.

Variable speed wind turbine generator system with current controlled voltage source inverter

Energy Technology Data Exchange (ETDEWEB)

Muyeen, S.M., E-mail: muyeen0809@yahoo.co [Dept. of Electrical Engineering, Petroleum Institute, P.O. Box 2533, Abu Dhabi (United Arab Emirates); Al-Durra, Ahmed [Dept. of Electrical Engineering, The Petroleum Institute, P.O. Box 2533, Abu Dhabi (United Arab Emirates); Tamura, J. [Dept. of EEE, Kitami Institute of Technology, 165 Koen-cho, Kitami 090-8507 (Japan)

2011-07-15

highlights: {yields} Current controlled voltage source inverter scheme for wind power application. {yields} Low voltage ride through of wind farm. {yields} Variable speed wind turbine driven permanent magnet synchronous generator-operation and control. -- Abstract: The present popular trend of wind power generation is to use variable speed wind turbine (VSWT) driving a doubly fed induction generator (DFIG), wound field synchronous generator (WFSG) or permanent magnet synchronous generator (PMSG). Among them, stability analyses of DFIG type of VSWT have already been reported in many literatures. However, transient stability and low voltage ride through (LVRT) characteristics analyses for synchronous generator type of VSWT is not sufficient enough. This paper focuses on detailed LVRT characteristic analysis of variable speed wind turbine driving a PMSG (VSWT-PMSG) with current controlled voltage source inverter (CC-VSI). Modeling and suitable control strategies for overall system are developed to augment the low voltage ride through capability of variable speed wind generator, considering recent wind farm grid code. Both symmetrical and unsymmetrical faults are analyzed as network disturbances in this paper. The permanent fault due to unsuccessful reclosing of circuit breakers is taken into consideration, which is a salient feature of this study. Moreover, the dynamic characteristic is analyzed using real wind speed data measured in Hokkaido Island, Japan. The proposed control scheme is simulated by using the standard power system simulation package PSCAD/EMTDC and results are verified by comparing that of voltage controlled voltage source inverter scheme available in power system literature.

Automatic control system for the pig ion source for the U-400 cyclotron

International Nuclear Information System (INIS)

Kutner, V.B.; Subbotin, V.G.; Sukhov, A.M.; Tret'yakov, Yu.P.; Fefilov, B.V.

1989-01-01

An automatic control system is described for the cyclotron U-400 multiply-charged ion source based on CAMAC apparatus and microprocesor controllers. The system allows the automatic tuning of the ion source to the necessary regime including the automatic start-up of discharge, the obtaining of the necessary parameters of sputtering, the automatic search for a maximum beam current within the given discharge parameters. The system performs tuning the ion source to the quasioptimal regime for 10-15 minutes with up to 5% deviation from the preset parameters. It is possible to stabilize the beam current within 3% using the automatic correction of the discharge regime. 6 refs.; 4 figs

Automatic control system of the PIG ion source for the U-400 cyclotron

International Nuclear Information System (INIS)

Kutner, V.B.; Subbotin, V.G.; Sukhov, A.M.; Tretyakov, Y.P.; Fefilov, B.V.; Kasyanov, A.A.; Rybin, V.M.

1990-01-01

An automatic control system is described for the multiply charged ion source of the U-400 cyclotron based on CAMAC apparatus and microprocessor controllers. The system allows the automatic tuning of the ion source to the necessary regime, including the automatic start-up of discharge, determination of the necessary parameters of sputtering, and the automatic search for a maximum beam current for given discharge parameters. The system performs the tuning of the ion source to the quasioptimal regime in 10--15 min with up to 5% deviation from the preset parameters. It is possible to stabilize the beam current within 3% using the automatic correction of the discharge regime

Selection and placement of best management practices used to reduce water quality degradation in Lincoln Lake watershed

Science.gov (United States)

Rodriguez, Hector German; Popp, Jennie; Maringanti, Chetan; Chaubey, Indrajeet

2011-01-01

An increased loss of agricultural nutrients is a growing concern for water quality in Arkansas. Several studies have shown that best management practices (BMPs) are effective in controlling water pollution. However, those affected with water quality issues need water management plans that take into consideration BMPs selection, placement, and affordability. This study used a nondominated sorting genetic algorithm (NSGA-II). This multiobjective algorithm selects and locates BMPs that minimize nutrients pollution cost-effectively by providing trade-off curves (optimal fronts) between pollutant reduction and total net cost increase. The usefulness of this optimization framework was evaluated in the Lincoln Lake watershed. The final NSGA-II optimization model generated a number of near-optimal solutions by selecting from 35 BMPs (combinations of pasture management, buffer zones, and poultry litter application practices). Selection and placement of BMPs were analyzed under various cost solutions. The NSGA-II provides multiple solutions that could fit the water management plan for the watershed. For instance, by implementing all the BMP combinations recommended in the lowest-cost solution, total phosphorous (TP) could be reduced by at least 76% while increasing cost by less than 2% in the entire watershed. This value represents an increase in cost of 5.49 ha-1 when compared to the baseline. Implementing all the BMP combinations proposed with the medium- and the highest-cost solutions could decrease TP drastically but will increase cost by 24,282 (7%) and $82,306 (25%), respectively.

Plans for a Collaboratively Developed Distributed Control System for the Spallation Neutron Source

International Nuclear Information System (INIS)

DeVan, W.R.; Gurd, D.P.; Hammonds, J.; Lewis, S.A.; Smith, J.D.

1999-01-01

The Spallation Neutron Source (SNS) is an accelerator-based pulsed neutron source to be built in Oak Ridge, Tennessee. The facility has five major sections - a ''front end'' consisting of a 65 keV H - ion source followed by a 2.5 MeV RFQ; a 1 GeV linac; a storage ring; a 1MW spallation neutron target (upgradeable to 2 MW); the conventional facilities to support these machines and a suite of neutron scattering instruments to exploit them. These components will be designed and implemented by five collaborating institutions: Lawrence Berkeley National Laboratory (Front End), Los Alamos National Laboratory (Linac); Brookhaven National Laboratory (Storage Ring); Argonne National Laboratory (Instruments); and Oak Ridge National Laboratory (Neutron Source and Conventional Facilities). It is proposed to implement a fully integrated control system for all aspects of this complex. The system will be developed collaboratively, with some degree of local autonomy for distributed systems, but centralized accountability. Technical integration will be based upon the widely-used EPICS control system toolkit, and a complete set of hardware and software standards. The scope of the integrated control system includes site-wide timing and synchronization, networking and machine protection. This paper discusses the technical and organizational issues of planning a large control system to be developed collaboratively at five different institutions, the approaches being taken to address those issues, as well as some of the particular technical challenges for the SNS control system

Controlling radioactive sources. Stronger 'cradle-to-grave' security needed, IAEA says

International Nuclear Information System (INIS)

2002-01-01

This article highlights the IAEA activities in the field of radiation safety and security of radiation sources and other radioactive materials in its Member States. The IAEA has been active in lending its expertise to search out and secure orphaned sources in several countries. Additionally more than 70 States have joined with the IAEA to collect and share information on trafficking incidents and other unauthorized movements of radioactive sources and other radioactive materials. In March 2002 the IAEA Board of Governors approved a multi-faceted Action plan to Combat Nuclear Terrorism that includes upgrading radiation safety and security. One programme is designed to ensure that significant, uncontrolled radioactive sources are brought under regulatory control and properly secured by providing assistance to Member States in their efforts to identify, locate and secure or dispose of orphan sources

Access control and interlock system at the Advanced Photon Source

International Nuclear Information System (INIS)

Forrestal, J.; Hogrefe, R.; Knott, M.; McDowell, W.; Reigle, D.; Solita, L.; Koldenhoven, R.; Haid, D.

1997-01-01

The Advanced Photon Source (APS) consists of a linac, position accumulator ring (PAR), booster synchrotron, storage ring, and up to 70 experimental beamlines. The Access Control and Interlock System (ACIS) utilizes redundant programmable logic controllers (PLCs) and a third hard-wired chain to protect personnel from prompt radiation generated by the linac, PAR, synchrotron, and storage ring. This paper describes the ACIS's design philosophy, configuration, hardware, functionality, validation requirements, and operational experience

40 CFR 450.24 - New source performance standards reflecting the best available demonstrated control technology...

Science.gov (United States)

2010-07-01

... performance standards reflecting the best available demonstrated control technology (NSPS). Any new source... 40 Protection of Environment 29 2010-07-01 2010-07-01 false New source performance standards reflecting the best available demonstrated control technology (NSPS). 450.24 Section 450.24 Protection of...

Influence of land development on stormwater runoff from a mixed land use and land cover catchment.

Science.gov (United States)

Paule-Mercado, M A; Lee, B Y; Memon, S A; Umer, S R; Salim, I; Lee, C-H

2017-12-01

Mitigating for the negative impacts of stormwater runoff is becoming a concern due to increased land development. Understanding how land development influences stormwater runoff is essential for sustainably managing water resources. In recent years, aggregate low impact development-best management practices (LID-BMPs) have been implemented to reduce the negative impacts of stormwater runoff on receiving water bodies. This study used an integrated approach to determine the influence of land development and assess the ecological benefits of four aggregate LID-BMPs in stormwater runoff from a mixed land use and land cover (LULC) catchment with ongoing land development. It used data from 2011 to 2015 that monitored 41 storm events and monthly LULC, and a Personalized Computer Storm Water Management Model (PCSWMM). The four aggregate LID-BMPs are: ecological (S1), utilizing pervious covers (S2), and multi-control (S3) and (S4). These LID-BMPs were designed and distributed in the study area based on catchment characteristics, cost, and effectiveness. PCSWMM was used to simulate the monitored storm events from 2014 (calibration: R 2 and NSE>0.5; RMSE 0.5; RMSE runoff data and LULC change patterns (only 2015 for LID-BMPs) were used. Results show that the expansion of bare land and impervious cover, soil alteration, and high amount of precipitation influenced the stormwater runoff variability during different phases of land development. The four aggregate LID-BMPs reduced runoff volume (34%-61%), peak flow (6%-19%), and pollutant concentrations (53%-83%). The results of this study, in addition to supporting local LULC planning and land development activities, also could be applied to input data for empirical modeling, and designing sustainable stormwater management guidelines and monitoring strategies. Copyright © 2017 Elsevier B.V. All rights reserved.

Sources of ionizing radiation in industry: licensing and control

International Nuclear Information System (INIS)

Dimitrov, V.

2001-01-01

In this paper are presented several methods, which the Inspection on the Safe Use of Atomic Energy applies for the control on the use of sources of ionizing radiation in industry. It reviews some problems, which we have to solve during our inspections. An analysis and assessment of them is done. The prescribed safety ensuring measures are discussed. (author)

Control of radioactive sources in industry through regulatory inspections

International Nuclear Information System (INIS)

Leocadio, J.C.; Ramalho, A.T.; Pinho, A.S.; Lourenco, M.M.J.; Nicola, M.S.; D'Avila, R.L.; Melo, I.F.; Cucco, A.C.S.

2005-01-01

In Brazil, the applications of ionizing radiation in industry are accomplished about 900 radioactive facilities, which handle approximately 3.000 radiation sources. The control of radioactive sources used in industrial installations authorized by the Brazilian Nuclear Energy Commission (CNEN) is accomplished by Servico de Radioprotecao na Industria Radiativa (SERIR) of the Instituto de Radioprotecao e Dosimetria (IRD), Rio de Janeiro, RJ, Brazil. This service carries out regulatory inspections in the practices of industrial radiography, nuclear gauges, industrial irradiators and oil wells logging. The frequency of inspections depends on the type of practice, ranging from a year to 5 years, depending on the risk involved. This paper presents a brief description of the situation of radiation safety in the use of radioactive sources in the industries of the country. The results obtained with regulatory inspections at industrial installations demonstrate that the conditions of safety and radiation protection in these facilities are satisfactory when compared with the technical regulations, both national and international

Deghosting, Demultiple, and Deblurring in Controlled-Source Seismic Interferometry

Directory of Open Access Journals (Sweden)

Joost van der Neut

2011-01-01

Full Text Available With controlled-source seismic interferometry we aim to redatum sources to downhole receiver locations without requiring a velocity model. Interferometry is generally based on a source integral over cross-correlation (CC pairs of full, perturbed (time-gated, or decomposed wavefields. We provide an overview of ghosts, multiples, and spatial blurring effects that can occur for different types of interferometry. We show that replacing cross-correlation by multidimensional deconvolution (MDD can deghost, demultiple, and deblur retrieved data. We derive and analyze MDD for perturbed and decomposed wavefields. An interferometric point spread function (PSF is introduced that can be obtained directly from downhole data. Ghosts, multiples, and blurring effects that may populate the retrieved gathers can be locally diagnosed with the PSF. MDD of perturbed fields can remove ghosts and deblur retrieved data, but it leaves particular multiples in place. To remove all overburden-related effects, MDD of decomposed fields should be applied.

Combining the Power of Statistical Analyses and Community Interviews to Identify Adoption Barriers for Stormwater Best-Management Practices

Science.gov (United States)

Hoover, F. A.; Bowling, L. C.; Prokopy, L. S.

2015-12-01

Urban stormwater is an on-going management concern in municipalities of all sizes. In both combined or separated sewer systems, pollutants from stormwater runoff enter the natural waterway system during heavy rain events. Urban flooding during frequent and more intense storms are also a growing concern. Therefore, stormwater best-management practices (BMPs) are being implemented in efforts to reduce and manage stormwater pollution and overflow. The majority of BMP water quality studies focus on the small-scale, individual effects of the BMP, and the change in water quality directly from the runoff of these infrastructures. At the watershed scale, it is difficult to establish statistically whether or not these BMPs are making a difference in water quality, given that watershed scale monitoring is often costly and time consuming, relying on significant sources of funds, which a city may not have. Hence, there is a need to quantify the level of sampling needed to detect the water quality impact of BMPs at the watershed scale. In this study, a power analysis was performed on data from an urban watershed in Lafayette, Indiana, to determine the frequency of sampling required to detect a significant change in water quality measurements. Using the R platform, results indicate that detecting a significant change in watershed level water quality would require hundreds of weekly measurements, even when improvement is present. The second part of this study investigates whether the difficulty in demonstrating water quality change represents a barrier to adoption of stormwater BMPs. Semi-structured interviews of community residents and organizations in Chicago, IL are being used to investigate residents understanding of water quality and best management practices and identify their attitudes and perceptions towards stormwater BMPs. Second round interviews will examine how information on uncertainty in water quality improvements influences their BMP attitudes and perceptions.

Design of Programmable LED Controller with a Variable Current Source for 3D Image Display

Directory of Open Access Journals (Sweden)

Kyung-Ryang Lee

2014-12-01

Full Text Available Conventional fluorescent light sources, as well as incandescent light sources are gradually being replaced by Light Emitting Diodes (LEDs for reducing power consumption in the image display area for multimedia application. An LED light source requires a controller with a low-power operation. In this paper, a low-power technique using adiabatic operation is applied for the implementation of LED controller with a stable constant-current, a low-power and low-heat function. From the simulation result, the power consumption of the proposed LED controller using adiabatic operation was reduced to about 87% in comparison with conventional operation with a constant VDD. The proposed circuit is expected to be an alternative LED controller which is sensitive to external conditions such as heat.

Procedures for identifying reasonably available control technology for stationary sources of PM-10. Final report

International Nuclear Information System (INIS)

Fitzpatrick, M.J.; Ellefson, R.

1992-09-01

The guidance document sets forth procedures and identifies sources of information that will assist State and local air pollution control agencies in determining Reasonably Available Control Technology (RACT) for PM-10 (particulate matter having a nominal aerometric diameter of 10 microns or less) emission from existing stationary sources on a case-by-case basis. It provides an annotated bibliography of documents to aid in identifying the activities that cause PM-10 emissions as well as applicable air pollution control measures and their effectiveness in reducing emissions. The most stringent state total particulate matter (PM) emission limits are identified for several categories of PM-10 sources and compared to available emission test data. Finally, guidance is provided on procedures for estimating total capital investment and total annual cost of the control measures which are generally used to control PM-10 emissions

Stability analysis of direct current control in current source rectifier

DEFF Research Database (Denmark)

Lu, Dapeng; Wang, Xiongfei; Blaabjerg, Frede

2017-01-01

Current source rectifier with high switching frequency has a great potential for improving the power efficiency and power density in ac-dc power conversion. This paper analyzes the stability of direct current control based on the time delay effect. Small signal model including dynamic behaviors...

A Self-Assessment of the Effectiveness to Control Radiation Sources in Sierra Leone

Energy Technology Data Exchange (ETDEWEB)

Bun-Tejan, Umaru Remilekun [KAIST, Daejeon (Korea, Republic of); Lee, Byung Soo [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2016-10-15

There is an urgent need to effectively control sources of ionizing radiation. Sources of ionizing radiation pose serious occupational, public health, and environmental consequences, if not properly controlled. The government of Sierra Leone knows the importance of controlling these sources of ionizing radiation and of establishing an independent Nuclear Safety Infrastructure. Sierra Leone has no nuclear facilities but, it is rapidly developing its infrastructure in order to obtain nuclear technology. However, the regulatory effectiveness in controlling radiation risk is essential for the International Atomic Energy Agency to allow the transfer of nuclear technology. For this reason, this study will evaluate the status of the regulatory authority in Sierra Leone to control radiation risk. The International Atomic Energy Agency (IAEA) review mission to Sierra Leone found that the RPBA did not give sufficient enforcement powers to the Board Secretariat. The research evaluated the status of the regulatory authority of Sierra Leone. The status of the regulatory authority was evaluated against several parameters including management systems, regulatory processes, authorization, inspection, and enforcement. The ability to effectively control ionizing radiation sources depends on the status of the regulatory body. The Integrated Regulatory Review Service Report on Sierra Leone led us to infer that there is a need for the regulatory authority to rapidly improve its ability to control ionizing radiation sources in the country. The findings however, revealed that the overall strengths of the regulatory body in Sierra Leone slightly outnumber the weaknesses. Management systems have a ratio of 0.85:1 of strengths to weaknesses. This ratio makes management systems the weakest parameter evaluated. Thus there is need for stronger collaboration between management staff. The Regulatory processes have a ratio of 1.3:1, authorizations have a ratio of 4.3:1, inspections have ratio of 2

A Self-Assessment of the Effectiveness to Control Radiation Sources in Sierra Leone

International Nuclear Information System (INIS)

Bun-Tejan, Umaru Remilekun; Lee, Byung Soo

2016-01-01

There is an urgent need to effectively control sources of ionizing radiation. Sources of ionizing radiation pose serious occupational, public health, and environmental consequences, if not properly controlled. The government of Sierra Leone knows the importance of controlling these sources of ionizing radiation and of establishing an independent Nuclear Safety Infrastructure. Sierra Leone has no nuclear facilities but, it is rapidly developing its infrastructure in order to obtain nuclear technology. However, the regulatory effectiveness in controlling radiation risk is essential for the International Atomic Energy Agency to allow the transfer of nuclear technology. For this reason, this study will evaluate the status of the regulatory authority in Sierra Leone to control radiation risk. The International Atomic Energy Agency (IAEA) review mission to Sierra Leone found that the RPBA did not give sufficient enforcement powers to the Board Secretariat. The research evaluated the status of the regulatory authority of Sierra Leone. The status of the regulatory authority was evaluated against several parameters including management systems, regulatory processes, authorization, inspection, and enforcement. The ability to effectively control ionizing radiation sources depends on the status of the regulatory body. The Integrated Regulatory Review Service Report on Sierra Leone led us to infer that there is a need for the regulatory authority to rapidly improve its ability to control ionizing radiation sources in the country. The findings however, revealed that the overall strengths of the regulatory body in Sierra Leone slightly outnumber the weaknesses. Management systems have a ratio of 0.85:1 of strengths to weaknesses. This ratio makes management systems the weakest parameter evaluated. Thus there is need for stronger collaboration between management staff. The Regulatory processes have a ratio of 1.3:1, authorizations have a ratio of 4.3:1, inspections have ratio of 2

Effects of Bone Morphogenic Proteins on Engineered Cartilage

Science.gov (United States)

Gooch, Keith, J.; Blunk, Torsten; Courter, Donald L.; Sieminski, Alisha; Vunjak-Novakovic, Gordana; Freed, Lisa E.

2007-01-01

A report describes experiments on the effects of bone morphogenic proteins (BMPs) on engineered cartilage grown in vitro. In the experiments, bovine calf articular chondrocytes were seeded onto biodegradable polyglycolic acid scaffolds and cultured in, variously, a control medium or a medium supplemented with BMP-2, BMP-12, or BMP-13 in various concentrations. Under all conditions investigated, cell-polymer constructs cultivated for 4 weeks macroscopically and histologically resembled native cartilage. At a concentration of 100 ng/mL, BMP-2, BMP-12, or BMP-13 caused (1) total masses of the constructs to exceed those of the controls by 121, 80, or 62 percent, respectively; (2) weight percentages of glycosaminoglycans in the constructs to increase by 27, 18, or 15, respectively; and (3) total collagen contents of the constructs to decrease to 63, 89, or 83 percent of the control values, respectively. BMP-2, but not BMP-12 or BMP-13, promoted chondrocyte hypertrophy. These observations were interpreted as suggesting that the three BMPs increase the growth rates and modulate the compositions of engineered cartilage. It was also concluded that in vitro engineered cartilage is a suitable system for studying effects of BMPs on chondrogenesis in a well-defined environment.

The importance of governmental control of radioactive sources used in industrial applications

International Nuclear Information System (INIS)

Anna Firpo Fuerth, Q.F.; Beatriz Souto Ameigenda, Q.F.

1998-01-01

Industrial applications of radioactive sources require good management practices dealing with control and registration. In the following case, a special event occurred between two routine inspections: trading. Then a new human factor came into scene: workers with no specific training and knowledge related to radioactive sources. The up going situation triggered emergency procedures. Finally, there were no negative consequences. (author)

Standards and the design of the advanced photon source control system

International Nuclear Information System (INIS)

McDowell, W.P.; Knott, M.J.; Lenkszus, F.R.

1992-01-01

The Advanced Photon Source (APS), now under construction at Argonne National Laboratory (ANL), is a 7 GeV positron storage ring dedicated to research facilities using synchrotron radiation. This ring, along with its injection accelerators is to be controlled and monitored with a single, flexible, and expandable control system. This paper will cover the present status of the APS control system as well as discuss the design decisions which led us to use industrial standards and collaborations with other laboratories whenever possible to develop a control system. It will explain the APS control system and illustrate how the use of standards has allowed APS to design a control system whose implementation addresses these issues. (J.P.N.)

Stability and vibration control in synchrotron light source buildings

Energy Technology Data Exchange (ETDEWEB)

Godel, J.B.

1991-01-01

Synchrotron light sources have undergone three generations of development in the last two decades. The National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory has two second generation'' storage rings that currently provide the world's most intense sources of photons in the VUV and X-ray spectral ranges. There are almost 90 beam lines serving a community of 2600 scientists from 370 institutions. They are engaged in basic and applied research in physics, chemistry, biology, medicine, materials science and various technologies. When design of the NSLS began in 1977, emphasis was given to the stability of the concrete slab on which the storage rings and experimental beam lines were placed. Stability is the result of controlling: vibration from sources internal and external to the building, thermal effects of air and water temperature variations, foundation settlement and contact between the slab and underlying subsoil. With the advent of new research where highly focused beams of x-rays must be placed on increasingly smaller targets located 35 meters or more from the source, and the development of x-ray lithography with resolutions approaching 0.1 micron at chip exposure stations, even greater attention to stability is required in building designs. This paper will review the results of the successful NSLS experience and give an integrated design approach that includes elements which contribute to instabilities, and the means available to reduce them to acceptable levels.

Stability and vibration control in synchrotron light source buildings

Energy Technology Data Exchange (ETDEWEB)

Godel, J.B.

1991-12-31

Synchrotron light sources have undergone three generations of development in the last two decades. The National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory has two ``second generation`` storage rings that currently provide the world`s most intense sources of photons in the VUV and X-ray spectral ranges. There are almost 90 beam lines serving a community of 2600 scientists from 370 institutions. They are engaged in basic and applied research in physics, chemistry, biology, medicine, materials science and various technologies. When design of the NSLS began in 1977, emphasis was given to the stability of the concrete slab on which the storage rings and experimental beam lines were placed. Stability is the result of controlling: vibration from sources internal and external to the building, thermal effects of air and water temperature variations, foundation settlement and contact between the slab and underlying subsoil. With the advent of new research where highly focused beams of x-rays must be placed on increasingly smaller targets located 35 meters or more from the source, and the development of x-ray lithography with resolutions approaching 0.1 micron at chip exposure stations, even greater attention to stability is required in building designs. This paper will review the results of the successful NSLS experience and give an integrated design approach that includes elements which contribute to instabilities, and the means available to reduce them to acceptable levels.

Stability and vibration control in synchrotron light source buildings

International Nuclear Information System (INIS)

Godel, J.B.

1991-01-01

Synchrotron light sources have undergone three generations of development in the last two decades. The National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory has two ''second generation'' storage rings that currently provide the world's most intense sources of photons in the VUV and X-ray spectral ranges. There are almost 90 beam lines serving a community of 2600 scientists from 370 institutions. They are engaged in basic and applied research in physics, chemistry, biology, medicine, materials science and various technologies. When design of the NSLS began in 1977, emphasis was given to the stability of the concrete slab on which the storage rings and experimental beam lines were placed. Stability is the result of controlling: vibration from sources internal and external to the building, thermal effects of air and water temperature variations, foundation settlement and contact between the slab and underlying subsoil. With the advent of new research where highly focused beams of x-rays must be placed on increasingly smaller targets located 35 meters or more from the source, and the development of x-ray lithography with resolutions approaching 0.1 micron at chip exposure stations, even greater attention to stability is required in building designs. This paper will review the results of the successful NSLS experience and give an integrated design approach that includes elements which contribute to instabilities, and the means available to reduce them to acceptable levels

Strategies for delivering bone morphogenetic protein for bone healing

Energy Technology Data Exchange (ETDEWEB)

Begam, Howa [School of Bioscience and Engineering, Jadavpur University, Kolkata 700032 (India); Nandi, Samit Kumar, E-mail: samitnandi1967@gmail.com [Department of Veterinary Surgery, Radiology West Bengal University of Animal and Fishery Sciences, Kolkata 700037 (India); Kundu, Biswanath, E-mail: biswa_kundu@rediffmail.com [Bioceramics and Coating Division, CSIR-Central Glass and Ceramic Research Institute, Kolkata 700032 (India); Chanda, Abhijit [Department of Mechanical Engineering, Jadavpur University, Kolkata 700032 (India)

2017-01-01

Bone morphogenetic proteins (BMPs) are the most significant growth factors that belong to the Transforming Growth Factor Beta (TGF-β) super-family. Though more than twenty members of this family have been identified so far in humans, Food and Drug Administration (FDA) approved two growth factors: BMP-2 and BMP-7 for treatments of spinal fusion and long-bone fractures with collagen carriers. Currently BMPs are clinically used in spinal fusion, oral and maxillofacial surgery and also in the repair of long bone defects. The efficiency of BMPs depends a lot on the selection of suitable carriers. At present, different types of carrier materials are used: natural and synthetic polymers, calcium phosphate and ceramic-polymer composite materials. Number of research articles has been published on the minute intricacies of the loading process and release kinetics of BMPs. Despite the significant evidence of its potential for bone healing demonstrated in animal models, future clinical investigations are needed to define dose, scaffold and route of administration. The efficacy and application of BMPs in various levels with a proper carrier and dose is yet to be established. The present article collates various aspects of success and limitation and identifies the prospects and challenges associated with the use of BMPs in orthopaedic surgery. - Highlights: • Currently BMPs are clinically used in spinal fusion, oral and maxillofacial surgery and also in repair of long bone defects. • Different types of carrier materials are used: natural, synthetic polymers, calcium phosphate and ceramic-polymer composite • Efficacy and application of BMPs in various levels with proper carrier and dose is yet to be established • Number of research articles has been published on minute intricacies of loading process and release kinetics of BMPs • Present article collates success, limitation and identifies prospects, challenges for use of BMPs in orthopaedic surgery.

National system of notification, authorization and inspection for the control of radiation sources in Ghana

International Nuclear Information System (INIS)

Schandorf, C.; Darko, E.O.; Yeboah, J.; Asiamah, S.D.

2001-01-01

The Radiation Protection Board (RPB) was established in 1993 in Ghana as the regulatory authority for radiation protection and safety of radiation sources; its functions are prescribed in the 1993 national radiation protection regulation. The report describes how the country's radiation protection and safety infrastructure have been established, including the RPB's organizational structure, with reference in particular to the main activities carried out by both the Regulatory Control Department and the Radiation and Waste Safety Department. It also briefly mentions the existing RPB human resources; the national system of notification, authorization and inspection of radiation sources; the inventory of radiation sources; and the management of disused radiation sources. Finally, the report identifies the two main problem areas regarding the regulatory control of radiation sources in the country. (author)

Autonomous Micro-Air-Vehicle Control Based on Visual Sensing for Odor Source Localization

Directory of Open Access Journals (Sweden)

Kenzo Kurotsuchi

2017-07-01

Full Text Available In this paper, we propose a novel control method for autonomous-odor-source localization using visual and odor sensing by micro air vehicles (MAVs. Our method is based on biomimetics, which enable highly autonomous localization. Our method does not need any instruction signals, including even global positioning system (GPS signals. An experimenter simply blows a whistle, and the MAV will then start to hover, to seek an odor source, and to keep hovering near the source. The GPS-signal-free control based on visual sense enables indoor/underground use. Moreover, the MAV is light-weight (85 grams and does not cause harm to others even if it accidentally falls. Experiments conducted in the real world were successful in enabling odor source localization using the MAV with a bio-inspired searching method. The distance error of the localization was 63 cm, more accurate than the target distance of 120 cm for individual identification. Our odor source localization is the first step to a proof of concept for a danger warning system. These localization experiments were the first step to a proof of concept for a danger warning system to enable a safer and more secure society.

NicoLase-An open-source diode laser combiner, fiber launch, and sequencing controller for fluorescence microscopy.

Directory of Open Access Journals (Sweden)

Philip R Nicovich

Full Text Available Modern fluorescence microscopy requires software-controlled illumination sources with high power across a wide range of wavelengths. Diode lasers meet the power requirements and combining multiple units into a single fiber launch expands their capability across the required spectral range. We present the NicoLase, an open-source diode laser combiner, fiber launch, and software sequence controller for fluorescence microscopy and super-resolution microscopy applications. Two configurations are described, giving four or six output wavelengths and one or two single-mode fiber outputs, with all CAD files, machinist drawings, and controller source code openly available.

Molecular mechanisms of BMP-induced bone formation: Cross-talk between BMP and NF-κB signaling pathways in osteoblastogenesis

Directory of Open Access Journals (Sweden)

Eijiro Jimi

2010-02-01

Full Text Available Osteoblasts are bone-forming cells that differentiate from mesenchymal stem cells. Differentiation processes are coordinately and dynamically controlled in the mesenchymal cells by specific signal transduction pathways. Bone morphogenetic proteins (BMPs, members of the TGF-β superfamily, induce not only bone formation in vivo, but also osteoblast differentiation of mesenchymal cells in vitro. BMP signals are transduced from plasma membrane receptors to the nucleus through both Smad-dependent and -independent pathways, and are regulated by many extracellular and intercellular proteins that interact with BMPs or components of BMP signaling pathways. To understand the molecular mechanisms underlying the role of BMPs in osteoblast differentiation, it is important to elucidate the BMP signaling transduction pathways that are active during osteoblast differentiation. In this review, we summarize the BMP signaling pathways that are known to function in osteoblast development. We also describe our recent findings regarding the molecular mechanisms underlying the cross-talk between BMP/Smad and NF-κB pathways in osteoblast differentiation.

Atmospheric heavy metals and Arsenic in China: Situation, sources and control policies

Science.gov (United States)

Duan, Jingchun; Tan, Jihua

2013-08-01

In recent years, heavy metal pollution accidents were reported frequently in China. The atmospheric heavy metal pollution is drawing all aspects of attention. This paper summarizes the recent research results from our studies and previous studies in recent years in China. The level, temporal variation, seasonal variation and size distribution of the heavy metals of atmospheric Lead(Pb), Vanadium(V), Manganese(Mn), Nickel(Ni), Chromium(Cr), Cadmium(Cd), Copper(Cu), Zinc(Zn) and Arsenic(As) were characterized in China. The emission characteristics and sources of atmospheric heavy metals and As in China were reviewed. Coal burning, iron and steel industry and vehicle emission are important sources in China. Control policies and effects in China were reviewed including emission standards, ambient air quality standards, phase out of leaded gasoline and so on, and further works for atmospheric heavy metals control were suggested. The comprehensive heavy metals pollution control measures and suggestions were put forward based on the summarization of the development and experience of the atmospheric heavy metal pollution control abroad.

Preparation method and quality control of multigamma volume sources with different matrices.

Science.gov (United States)

Listkowska, A; Lech, E; Saganowski, P; Tymiński, Z; Dziel, T; Cacko, D; Ziemek, T; Kołakowska, E; Broda, R

2018-04-01

The aim of the work was to develop new radioactive standard sources based on epoxy resins. The optimal proportions of the components and the homogeneity of the matrices were determined. The activity of multigamma sources prepared in Marinelli beakers was determined with reference to the National Standard of Radionuclides Activity in Poland. The difference of radionuclides activity values determined using calibrated gamma spectrometer and the activity of standard solutions used are in most cases significantly lower than measurement uncertainty limits. Sources production method and quality control procedure have been developed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Status and design of the Advanced Photon Source control system

International Nuclear Information System (INIS)

McDowell, W.; Knott, M.; Lenkszus, F.; Kraimer, M.; Arnold, N.; Daly, R.

1993-01-01

This paper presents the current status of the Advanced Photon Source (APS) control system. It will discuss the design decisions which led us to use industrial standards and collaborations with other laboratories to develop the APS control system. The system uses high performance graphic workstations and the X-windows Graphical User Interface (GUI) at the operator interface level. It connects to VME/VXI-based microprocessors at the field level using TCP/IP protocols over high performance networks. This strategy assures the flexibility and expansibility of the control system. A defined interface between the system components will allow the system to evolve with the direct addition of future, improved equipment and new capabilities

Two Model-Based Methods for Policy Analyses of Fine Particulate Matter Control in China: Source Apportionment and Source Sensitivity

Science.gov (United States)

Li, X.; Zhang, Y.; Zheng, B.; Zhang, Q.; He, K.

2013-12-01

Anthropogenic emissions have been controlled in recent years in China to mitigate fine particulate matter (PM2.5) pollution. Recent studies show that sulfate dioxide (SO2)-only control cannot reduce total PM2.5 levels efficiently. Other species such as nitrogen oxide, ammonia, black carbon, and organic carbon may be equally important during particular seasons. Furthermore, each species is emitted from several anthropogenic sectors (e.g., industry, power plant, transportation, residential and agriculture). On the other hand, contribution of one emission sector to PM2.5 represents contributions of all species in this sector. In this work, two model-based methods are used to identify the most influential emission sectors and areas to PM2.5. The first method is the source apportionment (SA) based on the Particulate Source Apportionment Technology (PSAT) available in the Comprehensive Air Quality Model with extensions (CAMx) driven by meteorological predictions of the Weather Research and Forecast (WRF) model. The second method is the source sensitivity (SS) based on an adjoint integration technique (AIT) available in the GEOS-Chem model. The SA method attributes simulated PM2.5 concentrations to each emission group, while the SS method calculates their sensitivity to each emission group, accounting for the non-linear relationship between PM2.5 and its precursors. Despite their differences, the complementary nature of the two methods enables a complete analysis of source-receptor relationships to support emission control policies. Our objectives are to quantify the contributions of each emission group/area to PM2.5 in the receptor areas and to intercompare results from the two methods to gain a comprehensive understanding of the role of emission sources in PM2.5 formation. The results will be compared in terms of the magnitudes and rankings of SS or SA of emitted species and emission groups/areas. GEOS-Chem with AIT is applied over East Asia at a horizontal grid

Control of the safety and security of radiation sources in Argentina

International Nuclear Information System (INIS)

Oliveira, A.A.

2001-01-01

The report refers to the main elements of the regulatory infrastructure in Argentina, noting as relevant the promulgation in 1997 of the Act 24.804, which established the Nuclear Regulatory Authority (ARN) as an independent agency empowered to establish standards and enforce their application with regard to the possession and use of radiation sources. Important elements of such regulatory infrastructure are described in the report, and in particular those explaining the existing licensing system, the basic radiological safety and security requirements, the enforcement programme, and the key actions considered for the appropriate control of radioactive sources. In this respect, the report emphasizes the importance of the management of disused and orphan sources, and the role of education and training. (author)

General problems associated with the control and safe use of radiation sources (199)

International Nuclear Information System (INIS)

Ahmed, J.U.

1993-01-01

There are problems at various levels in ensuring safety in the use of radiation sources. A relatively new problem that warrants international action is the smuggling of radioactive material across international borders. An international convention on the control and safe use of radiation sources is essential to provide a universally harmonized mechanism for ensuring safety

Fibroblast growth factor 2 inhibits up-regulation of bone morphogenic proteins and their receptors during osteoblastic differentiation of human mesenchymal stem cells

Energy Technology Data Exchange (ETDEWEB)

Biver, Emmanuel, E-mail: ebiver@yahoo.fr [Physiopathology of Inflammatory Bone Diseases, EA 4490, University Lille North of France, Quai Masset, Bassin Napoleon, BP120, 62327 Boulogne sur Mer (France); Department of Rheumatology, Lille University Hospital, Roger Salengro Hospital, 59037 Lille cedex (France); Service of Bone Diseases, Department of Internal Medicine Specialties, University Hospital of Geneva, CH-1211 Geneva 14 (Switzerland); Soubrier, Anne-Sophie [Physiopathology of Inflammatory Bone Diseases, EA 4490, University Lille North of France, Quai Masset, Bassin Napoleon, BP120, 62327 Boulogne sur Mer (France); Department of Rheumatology, Lille University Hospital, Roger Salengro Hospital, 59037 Lille cedex (France); Thouverey, Cyril [Service of Bone Diseases, Department of Internal Medicine Specialties, University Hospital of Geneva, CH-1211 Geneva 14 (Switzerland); Cortet, Bernard [Physiopathology of Inflammatory Bone Diseases, EA 4490, University Lille North of France, Quai Masset, Bassin Napoleon, BP120, 62327 Boulogne sur Mer (France); Department of Rheumatology, Lille University Hospital, Roger Salengro Hospital, 59037 Lille cedex (France); Broux, Odile [Physiopathology of Inflammatory Bone Diseases, EA 4490, University Lille North of France, Quai Masset, Bassin Napoleon, BP120, 62327 Boulogne sur Mer (France); Caverzasio, Joseph [Service of Bone Diseases, Department of Internal Medicine Specialties, University Hospital of Geneva, CH-1211 Geneva 14 (Switzerland); Hardouin, Pierre [Physiopathology of Inflammatory Bone Diseases, EA 4490, University Lille North of France, Quai Masset, Bassin Napoleon, BP120, 62327 Boulogne sur Mer (France)

2012-11-02

Highlights: Black-Right-Pointing-Pointer FGF modulates BMPs pathway in HMSCs by down-regulating BMP/BMPR expression. Black-Right-Pointing-Pointer This effect is mediated by ERK and JNK MAPKs pathways. Black-Right-Pointing-Pointer Crosstalk between FGF and BMPs must be taken into account in skeletal bioengineering. Black-Right-Pointing-Pointer It must also be considered in the use of recombinant BMPs in orthopedic and spine surgeries. -- Abstract: Understanding the interactions between growth factors and bone morphogenic proteins (BMPs) signaling remains a crucial issue to optimize the use of human mesenchymal stem cells (HMSCs) and BMPs in therapeutic perspectives and bone tissue engineering. BMPs are potent inducers of osteoblastic differentiation. They exert their actions via BMP receptors (BMPR), including BMPR1A, BMPR1B and BMPR2. Fibroblast growth factor 2 (FGF2) is expressed by cells of the osteoblastic lineage, increases their proliferation and is secreted during the healing process of fractures or in surgery bone sites. We hypothesized that FGF2 might influence HMSC osteoblastic differentiation by modulating expressions of BMPs and their receptors. BMP2, BMP4, BMPR1A and mainly BMPR1B expressions were up-regulated during this differentiation. FGF2 inhibited HMSCs osteoblastic differentiation and the up-regulation of BMPs and BMPR. This effect was prevented by inhibiting the ERK or JNK mitogen-activated protein kinases which are known to be activated by FGF2. These data provide a mechanism explaining the inhibitory effect of FGF2 on osteoblastic differentiation of HMSCs. These crosstalks between growth and osteogenic factors should be considered in the use of recombinant BMPs in therapeutic purpose of fracture repair or skeletal bioengineering.

Multi-sources model and control algorithm of an energy management system for light electric vehicles

International Nuclear Information System (INIS)

Hannan, M.A.; Azidin, F.A.; Mohamed, A.

2012-01-01

Highlights: ► An energy management system (EMS) is developed for a scooter under normal and heavy power load conditions. ► The battery, FC, SC, EMS, DC machine and vehicle dynamics are modeled and designed for the system. ► State-based logic control algorithms provide an efficient and feasible multi-source EMS for light electric vehicles. ► Vehicle’s speed and power are closely matched with the ECE-47 driving cycle under normal and heavy load conditions. ► Sources of energy changeover occurred at 50% of the battery state of charge level in heavy load conditions. - Abstract: This paper presents the multi-sources energy models and ruled based feedback control algorithm of an energy management system (EMS) for light electric vehicle (LEV), i.e., scooters. The multiple sources of energy, such as a battery, fuel cell (FC) and super-capacitor (SC), EMS and power controller, DC machine and vehicle dynamics are designed and modeled using MATLAB/SIMULINK. The developed control strategies continuously support the EMS of the multiple sources of energy for a scooter under normal and heavy power load conditions. The performance of the proposed system is analyzed and compared with that of the ECE-47 test drive cycle in terms of vehicle speed and load power. The results show that the designed vehicle’s speed and load power closely match those of the ECE-47 test driving cycle under normal and heavy load conditions. This study’s results suggest that the proposed control algorithm provides an efficient and feasible EMS for LEV.

AHP Expert Programme As A Tool For Unsealed Sources Contamination Control Of The Environment

International Nuclear Information System (INIS)

Amin, E.T.; Ibrahim, M.S.; Hussein, A.Z.

2007-01-01

Unsealed sources of radionuclides are widely used in hot laboratories of medical centers and hospitals which can be easily dispersed and may be taken undue into the body. The presence of radioactive substances inside the human body generates risk of internal intakes of radionuclides and organ's tissue retention. In order to make control for any contamination occurring from unsealed sources, an AHP programme (PC programme) has been developed so that it includes all data of most unsealed sources used in the hot laboratories of nuclear medicine units at hospitals/medical centers. Sequence of questions are retrieved by the programme in relevance to the place address, uses, activity and half life of the unsealed radioisotopes that may cause contamination. The programme will also give information output about the hospital that use the unsealed source and its location which facilitate emergency planning and contamination control to the environment

Direct Power Control for Three-Phase Two-Level Voltage-Source Rectifiers Based on Extended-State Observation

DEFF Research Database (Denmark)

Song, Zhanfeng; Tian, Yanjun; Yan, Zhuo

2016-01-01

This paper proposed a direct power control strategy for three-phase two-level voltage-source rectifiers based on extended-state observation. Active and reactive powers are directly regulated in the stationary reference frame. Similar to the family of predictive controllers whose inherent characte......This paper proposed a direct power control strategy for three-phase two-level voltage-source rectifiers based on extended-state observation. Active and reactive powers are directly regulated in the stationary reference frame. Similar to the family of predictive controllers whose inherent...

Active control of aircraft engine inlet noise using compact sound sources and distributed error sensors

Science.gov (United States)

Burdisso, Ricardo (Inventor); Fuller, Chris R. (Inventor); O'Brien, Walter F. (Inventor); Thomas, Russell H. (Inventor); Dungan, Mary E. (Inventor)

1996-01-01

An active noise control system using a compact sound source is effective to reduce aircraft engine duct noise. The fan noise from a turbofan engine is controlled using an adaptive filtered-x LMS algorithm. Single multi channel control systems are used to control the fan blade passage frequency (BPF) tone and the BPF tone and the first harmonic of the BPF tone for a plane wave excitation. A multi channel control system is used to control any spinning mode. The multi channel control system to control both fan tones and a high pressure compressor BPF tone simultaneously. In order to make active control of turbofan inlet noise a viable technology, a compact sound source is employed to generate the control field. This control field sound source consists of an array of identical thin, cylindrically curved panels with an inner radius of curvature corresponding to that of the engine inlet. These panels are flush mounted inside the inlet duct and sealed on all edges to prevent leakage around the panel and to minimize the aerodynamic losses created by the addition of the panels. Each panel is driven by one or more piezoelectric force transducers mounted on the surface of the panel. The response of the panel to excitation is maximized when it is driven at its resonance; therefore, the panel is designed such that its fundamental frequency is near the tone to be canceled, typically 2000-4000 Hz.

Overview of the Spallation Neutron Source Linac Low-Level RF Control System

CERN Document Server

Champion, Mark; Doolittle, Lawrence; Kasemir, Kay-Uwe; Ma, Hengjie; Piller, Maurice; Ratti, Alessandro

2005-01-01

The design and production of the Spallation Neutron Source Linac Low-Level RF control system is complete, and installation will be finished in Spring 2005. The warm linac beam commissioning run in Fall 2004 was the most extensive test to date of the LLRF control system, with fourteen (of an eventual 96) systems operating simultaneously. In this paper we present an overview of the LLRF control system, the experience in designing, building and installing the system, and operational results.

Effectiveness of best management practices that have application to forest roads: a literature synthesis

Science.gov (United States)

Pamela J. Edwards; Frederica Wood; Robin L. Quinlivan

2016-01-01

Literature describing the effectiveness of best management practices (BMPs) applicable to forest roads is reviewed and synthesized. Effectiveness is considered from the perspective of protecting water quality and water resources. Both paved and unpaved forest roads are considered, but BMPs that involve substantial engineering are not considered. Some of the BMPs...

PM10 standards and nontraditional particulate source controls: A summary of the A ampersand WMA/EPA international specialty conference

International Nuclear Information System (INIS)

Chow, J.C.; Watson, J.G.; Ono, D.M.; Mathai, C.V.

1993-01-01

An international specialty conference, jointly sponsored by the Air ampersand Waste Management Association (A ampersand WMA) and the US Environmental Protection Agency (EPA), entitled open-quotes PM 10 Standards and Nontraditional Particulate Source Controls,close quotes was held in Scottsdale, Arizona, January 12-15, 1992. The conference included 92 presentations in 17 technical sessions. Eight-one peer-reviewed technical papers, two keynote addresses and one panel session summary describing novel applications, measurement processes, modeling techniques and control measures for nontraditional pollution sources are assembled in the Transactions. The technical issues addressed during the conference included: (1) measurement methods and data bases; (2) emissions source characterization; (3) source apportionment of nontraditional sources; (4) fugitive dust characterization and control technologies; (5) vegetative burning characterization and control technologies; (6) sources and controls of secondary aerosol and motor vehicle precursors; and (7) regulatory policies and State Implementation Plan (SIP) development. This paper gives an overview of the technical program. 105 refs., 1 tab

Comparative study of microcontroller controlled four-wire voltage and current source shunt active power filters

Energy Technology Data Exchange (ETDEWEB)

Pettersson, S.

2009-07-01

During the past two decades, active power filters have increasingly grown their popularity as a viable method for improving electric power quality. The main reasons for this have been the advent of fast self-commutating solid-state devices, the progression of digital technology and the improved sensor technology. Four-wire active power filters provide an efficient solution for improving the quality of supply in grounded three-phase systems or three-phase systems with neutral conductors, which are commonly used for powering residential, office and public buildings. Four-wire active power filters are applicable in compensating current harmonics, reactive power, neutral current and load phase imbalance.This thesis presents a comparative study of microcontroller controlled four-wire voltage and current source shunt active power filters. The study includes two voltage source topologies and a current source topology with two different dc-link energy storage structures, which are compared on the basis of their filtering properties, filtering performance and efficiency. The obtained results are used for determining the suitability of current source technology for four-wire active power filtering and finding the most viable four-wire shunt active power filter topology. One commonly recognized disadvantage of the current source active power filter has always been the bulky dc-link inductor. To reduce the size of the dc-link inductor, an alternative dc-link structure for current source active power filters was introduced in the late 80's. The hybrid energy storage consists of both inductive and capacitive energy storage elements, two diodes and two controllable semiconductor switching devices. Since the capacitive element is used as a main storage unit, the inductance of the dc-link inductor can be considerably reduced. However, the original dc current control method proposed is not able to utilize the full potential of the hybrid energy storage and the inductance

Nutrient Application and Algal Blooms: Farmer Decisions Regarding the Use of Best Management Practices in Lake Erie's Maumee River Watershed

Science.gov (United States)

Heeren, A.; Toman, E.; Wilson, R. S.; Martin, J.

2016-12-01

Lake Erie is the most productive of the Great Lakes. However, harmful algal blooms (HABs) caused by nutrient run-off threaten the lake. Experts have proposed numerous best management practices (BMPs) designed to reduce nutrient and sediment run-off. However, for these practices to be effective at reducing HABs, a significant portion of farmers and landowners within Lake Erie's watersheds have to first adopt and implement these practices. In order to better understand how farmers and landowners make decisions about whether or not to adopt and implement BMPs we conducted a series of focus groups and a mail survey of Lake Erie's largest watershed. We found that many farmers were supportive of adopting BMPs. For example, 60% of farmers in the watershed have already adopted using grid soil sampling while another 30% are willing to adopt the practice in the future. However, other practices were less popular, for example, only 18% of farmers had already adopted cover crops. Farmers also expressed several reservations about adopting some BMPs. For example, farmers were concerned about the costs of some BMPs, such as cover crops and drainage management systems, and how such practices might interfere with the planting of subsequent crops. Our research has several implications for reducing nutrient production by promoting BMPs. First, we identified potential concerns and limitations farmers faced in implementing specific BMPs. For example, conservationists can design future programs and communication efforts to target these specific concerns. Second, through examining the socio-psychological and cognitive characteristics that influence farmer decision-making, we identified that willingness to adopt nutrient BMPs is association with how strongly a farmer identifies with conservation and how effective they believed the BMP was at reducing run-off. Messages and information about BMPs may be more effective if they are framed in a way that aligns with identities and beliefs about

Status of the Advanced Photon Source and its accelerator control system

International Nuclear Information System (INIS)

McDowell, W.; Knott, M.; Kraimer, K.M.

1993-01-01

This paper presents the current status of the Advanced Photon Source (APS), its control system and the Experimental Physics and Industrial Control System (EPICS) tools being used to implement this control system. The status of the physical plant and each of the accelerators as well as detailed descriptions of the software tools used to build the accelerator control system are presented. The control system uses high-performance graphic workstations and the X-windows graphical user interface (GUI) at the operator interface level. It connects to VME/VXI-based microprocessors at the field level using TCP/IP protocols over high-performance networks. This strategy assures the flexibility and expansibility of the control system. A defined interface between the system components will allow the system to evolve with the direct addition of future, improved equipment and new capabilities

Main Activities to Improve the Control of Radioactive Sources and Maintain an Effective Regulatory Nuclear Systems in Brazil

International Nuclear Information System (INIS)

Marechal, M.H.

2016-01-01

Since 2006, the Directorate of Nuclear Safety and Security, DRS, of National Nuclear Energy Commission, CNEN, has gone through many improvements. In 2006 CNEN signed the commitment to the recommendations of the Code of Conduct on The Safety and Security of Radioactive Sources and the Guidance on The Import and Export of Radioactive Sources. The DRS is responsible for the licensing and control of nuclear facilities, fuel cycle, waste management and the control of radioactive sources and authorizations of medical and industrial installations. In 2009 the department responsible for the control of radioactive sources and authorizations of medical and industrial installations implemented an “Electronic Management System” in which this System integrates the transport department and waste management department. The Electronic Management System is linked to the register of radioactive sources and facilities and there is an access on line to the Customs, making the control of import and export of radioactive sources robust, efficient and fast. During the period from 2006 until 2015 the most relevant regulations related to the control of radioactive sources and authorizations of medical and industrial installations were reviewed and some were elaborated and issued. These documents were in line with the Categorization of Radioactive Sources and the International Basic Safety Standards, issued in the IAEA Safety Standard Series as General Safety Requirements Part 3 (GSR Part 3). The paper describes all the steps that were adopted in order to implement these systems and the improvements on our Nuclear Regulatory Systems. (author)

Information Support of Optimal Control of Modes of Electric Systems with Renewable Energy Sources

Directory of Open Access Journals (Sweden)

Michalina Gryniewicz-Jaworska

2017-12-01

Full Text Available To provide necessary quality of electric energy and reliable supply and reduce environmental contamination as a result of energy units operation, renewable sources of energy (RSE, in particular solar electric stations (SES, wind electric stations (WES and small hydropower stations (SHES are intensively developed. The paper considers the conditions of optimality of renewable sources of energy (RSE functioning in electric systems, controllability of which is limited by the impact of non-stable weather conditions. The influence of control system information support on the efficiency of RSE usage is shown.

40 CFR 63.2343 - What are my requirements for emission sources not requiring control?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true What are my requirements for emission sources not requiring control? 63.2343 Section 63.2343 Protection of Environment ENVIRONMENTAL PROTECTION... (Non-Gasoline) What This Subpart Covers § 63.2343 What are my requirements for emission sources not...

The regulatory control over radiation sources: the Brazilian experience and some lessons learned from industrial applications

International Nuclear Information System (INIS)

Costa, E.L.C.; Gomes, J.D.R.L.; Gomes, R.S.; Costa, M.L.L.; Thomé, Z.D.; Instituto Militar de Engenharia

2017-01-01

This study gives an overview of the activities of the National Commission of Nuclear Energy (CNEN), as the Brazilian nuclear regulatory authority. These activities are described, especially those related to management of orphan sources and radioactive material in scrap metal considering the actions already put into place by CNEN during the licensing and controlling of radioactive sources in the industry and other facilities. In Brazil, there is not yet an effective system for controlling the scrap metal and recycling industry, thus a coordinated approach to achieve a harmonized and effective response with the involvement of third parties is needed, especially the metal industries and ores facilities. These practices call for stringent regulatory control, in order to reduce the occurrence of orphan sources, and consequently, radioactive material appearing in scrap metal. Some challenges of managing the national radiation sources register systems will be discussed, in order to cover effectively all the radiation source history (in a 'from the cradle to the grave' basis), and the dynamic maintenance and update of these data. The main industrial applications considered in this work are those dealing with constant movement of sources all over the country, with geographical issues to be considered in the managing and controlling actions, such as gammagraphy and well-logging. This study aims to identify and promote good practices to prevent inadvertent diversion of radioactive material, taking into account existing international recommendations and some lessons learned in national level. (author)

The regulatory control over radiation sources: the Brazilian experience and some lessons learned from industrial applications

Energy Technology Data Exchange (ETDEWEB)

Costa, E.L.C.; Gomes, J.D.R.L.; Gomes, R.S.; Costa, M.L.L.; Thomé, Z.D., E-mail: evaldo@cnen.gov.br, E-mail: jlopes@cnen.gov.br, E-mail: rogeriog@cnen.gov.br, E-mail: mara@cnen.gov.br, E-mail: zielithome@gmail.com [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil). Diretoria de Radioproteção e Segurança Nuclear; Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil). Seção de Engenharia Nuclear

2017-11-01

This study gives an overview of the activities of the National Commission of Nuclear Energy (CNEN), as the Brazilian nuclear regulatory authority. These activities are described, especially those related to management of orphan sources and radioactive material in scrap metal considering the actions already put into place by CNEN during the licensing and controlling of radioactive sources in the industry and other facilities. In Brazil, there is not yet an effective system for controlling the scrap metal and recycling industry, thus a coordinated approach to achieve a harmonized and effective response with the involvement of third parties is needed, especially the metal industries and ores facilities. These practices call for stringent regulatory control, in order to reduce the occurrence of orphan sources, and consequently, radioactive material appearing in scrap metal. Some challenges of managing the national radiation sources register systems will be discussed, in order to cover effectively all the radiation source history (in a 'from the cradle to the grave' basis), and the dynamic maintenance and update of these data. The main industrial applications considered in this work are those dealing with constant movement of sources all over the country, with geographical issues to be considered in the managing and controlling actions, such as gammagraphy and well-logging. This study aims to identify and promote good practices to prevent inadvertent diversion of radioactive material, taking into account existing international recommendations and some lessons learned in national level. (author)

Control of radiation sources in Brazil; Controle de fontes de radiacao no Brasil

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Silvia Maria Velasques de; Menezes, Sergio Ferreira; Alves Filho, Aristeu Dacio; Xavier, Ana Maria [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil). Superintendencia de Licenciamento e Controle

1997-12-31

The radiological accident occurred in Goiania, in 1987, brought to light several deficiencies in the conduction of the licensing processes of medical, industrial and research facilities that handle radioisotopes as well as int he control of radioactive sources in Brazil. The objective of this article is to describe some of the technical and administrative measures taken to ensure the adoption of appropriate radiological safety standards throughout the country, thus reducing the incidence of radiological accidents. (author) 9 refs., 6 figs., 5 tabs.; e-mail: corad at cnen.gov.br

An amplitude and phase control system for the TFTR rf heating sources

International Nuclear Information System (INIS)

Cutsogeorge, G.

1989-04-01

Feedback loops that control the amplitude and phase of the rf heating sources on TFTR are described. The method for providing arc protection is also discussed. Block diagrams and Bode plots are included. 6 figs

Control and reception of out of use radioactive sources at the CDTN/CNEN, Minas Gerais, Brazil

International Nuclear Information System (INIS)

Reis, Luiz C.A.; Guzella, Marcia F.R.; Seles, Sandro R.N.; Cuccia, Valeria

2011-01-01

For reception of the received sources and for accomplish with CNEN regulations and IAEA recommendations, the CDTN have implanted a system for receiving those sources and all the procedures for effective control and recovering of information. The CDTN posses a source deposit, a data bank for the inventory and also a Laboratory for Treatment of Sealed Sources

Sources and mitigation of interharmonics in back-to-back controllable drives

DEFF Research Database (Denmark)

Soltani, Hamid; Loh, Poh Chiang; Blaabjerg, Frede

2014-01-01

for the sources, leading to undistorted grid currents, which are growingly important as more drives are tied to the grid. It is shown that in the case of back-to-back controllable drives it is possible to reduce the input current interharmonic distortion caused by motor current imbalance....

Operational techniques employed for the liquid sodium source term control loops

International Nuclear Information System (INIS)

Chulos, L.E.

1976-01-01

Four Source Term Control Loops (STCLs) have been designed, constructed, and placed into operation at the Hanford Engineering Development Laboratory (HEDL) as part of the Radioactivity Control Technology program. The data obtained are used to determine the corrosion and deposition of LMFBR materials, including corrosion product radionuclides, in a non-isothermal flowing sodium system. The paper discusses operation of the STCL Facilities and, in particular, the methods used for controlling the oxygen content of the liquid sodium. These methods include cold trapping techniques, hot trapping, seeding the cold traps with sodium oxide, and precipitating the oxygen in the cold trap in a controlled manner. Operational problems encountered with the STCL Facilities and the techniques for correcting these problems are also discussed

Top-Down Control of Visual Alpha Oscillations: Sources of Control Signals and Their Mechanisms of Action

Science.gov (United States)

Wang, Chao; Rajagovindan, Rajasimhan; Han, Sahng-Min; Ding, Mingzhou

2016-01-01

Alpha oscillations (8–12 Hz) are thought to inversely correlate with cortical excitability. Goal-oriented modulation of alpha has been studied extensively. In visual spatial attention, alpha over the region of visual cortex corresponding to the attended location decreases, signifying increased excitability to facilitate the processing of impending stimuli. In contrast, in retention of verbal working memory, alpha over visual cortex increases, signifying decreased excitability to gate out stimulus input to protect the information held online from sensory interference. According to the prevailing model, this goal-oriented biasing of sensory cortex is effected by top-down control signals from frontal and parietal cortices. The present study tests and substantiates this hypothesis by (a) identifying the signals that mediate the top-down biasing influence, (b) examining whether the cortical areas issuing these signals are task-specific or task-independent, and (c) establishing the possible mechanism of the biasing action. High-density human EEG data were recorded in two experimental paradigms: a trial-by-trial cued visual spatial attention task and a modified Sternberg working memory task. Applying Granger causality to both sensor-level and source-level data we report the following findings. In covert visual spatial attention, the regions exerting top-down control over visual activity are lateralized to the right hemisphere, with the dipoles located at the right frontal eye field (FEF) and the right inferior frontal gyrus (IFG) being the main sources of top-down influences. During retention of verbal working memory, the regions exerting top-down control over visual activity are lateralized to the left hemisphere, with the dipoles located at the left middle frontal gyrus (MFG) being the main source of top-down influences. In both experiments, top-down influences are mediated by alpha oscillations, and the biasing effect is likely achieved via an inhibition

Summary of dynamic analyses of the advanced neutron source reactor inner control rods

International Nuclear Information System (INIS)

Hendrich, W.R.

1995-08-01

A summary of the structural dynamic analyses that were instrumental in providing design guidance to the Advanced Neutron source (ANS) inner control element system is presented in this report. The structural analyses and the functional constraints that required certain performance parameters were combined to shape and guide the design effort toward a prediction of successful and reliable control and scram operation to be provided by these inner control rods

Evaluation of best management practices under intensive irrigation using SWAT model

OpenAIRE

Dechmi, Farida; Skhiri, Ahmed

2013-01-01

Land management practices such as conservation tillage and optimum irrigation are routinely used to reduce non-point source pollution and improve water quality. The calibrated and validated SWAT-IRRIG model is the first modified SWAT version that reproduces well the irrigation return flows (IRF) when the irrigation source is outside of the watershed. The application of this SWAT version in intensive irrigated systems permits to better evaluate the best management practices (BMPs) in such syst...

Impedance-based Analysis of DC Link Control in Voltage Source Rectifiers

DEFF Research Database (Denmark)

Lu, Dapeng; Wang, Xiongfei; Blaabjerg, Frede

2018-01-01

This paper analyzes the dynamics influences of the outer dc link control in the voltage source rectifiers based on the impedance model. The ac-dc interactions are firstly presented by means of full order small signal model in dq frame, which shows the input voltage and load condition are the two...

Microfocus x-ray imaging of traceable pointlike {sup 22}Na sources for quality control

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, T.; Oda, K.; Sato, Y.; Ito, H.; Masuda, S.; Yamada, T.; Matsumoto, M.; Murayama, H.; Takei, H. [Allied Health Sciences, Kitasato University Kitasato 1-15-1, Minami-ku, Sagamihara-shi, Kanagawa 252-0373 (Japan); Positron Medical Center, Tokyo Metropolitan Institute of Gerontology Sakaecho 35-2, Itabashi-ku, Tokyo 173-0015 (Japan); Advanced Industrial Science and Technology (AIST) Central 2, Umezono 1-1-1, Tsukuba-shi, Ibaraki 305-8568 (Japan); Kanagawa Industrial Technology Center (KITC) Shimoimazumi 705-1, Ebina-shi, Kanagawa 243-0435 (Japan); Japan Radioisotope Association (JRIA) Komagome 2-28-45, Bunkyo-ku, Tokyo 113-8941 (Japan); Molecular Imaging Center, National Institute of Radiological Sciences Anagawa 4-9-1, Inage, Chiba 263-8555 (Japan); Graduate School of Medical Sciences, Kitasato University Kitasato 1-15-1, Minami-ku, Sagamihara-shi, Kanagawa 252-0373 (Japan)

2012-07-15

Purpose: The purpose of this study is to propose a microfocus x-ray imaging technique for observing the internal structure of small radioactive sources and evaluating geometrical errors quantitatively, and to apply this technique to traceable pointlike {sup 22}Na sources, which were designed for positron emission tomography calibration, for the purpose of quality control of the pointlike sources. Methods: A microfocus x-ray imaging system with a focus size of 0.001 mm was used to obtain projection x-ray images and x-ray CT images of five pointlike source samples, which were manufactured during 2009-2012. The obtained projection and tomographic images were used to observe the internal structure and evaluate geometrical errors quantitatively. Monte Carlo simulation was used to evaluate the effect of possible geometrical errors on the intensity and uniformity of 0.511 MeV annihilation photon pairs emitted from the sources. Results: Geometrical errors were evaluated with sufficient precision using projection x-ray images. CT images were used for observing the internal structure intuitively. As a result, four of the five examined samples were within the tolerance to maintain the total uncertainty below {+-}0.5%, given the source radioactivity; however, one sample was found to be defective. Conclusions: This quality control procedure is crucial and offers an important basis for using the pointlike {sup 22}Na source as a basic calibration tool. The microfocus x-ray imaging approach is a promising technique for visual and quantitative evaluation of the internal geometry of small radioactive sources.

Multi-rate control over AWGN channels via analog joint source-channel coding

KAUST Repository

Khina, Anatoly; Pettersson, Gustav M.; Kostina, Victoria; Hassibi, Babak

2017-01-01

We consider the problem of controlling an unstable plant over an additive white Gaussian noise (AWGN) channel with a transmit power constraint, where the signaling rate of communication is larger than the sampling rate (for generating observations and applying control inputs) of the underlying plant. Such a situation is quite common since sampling is done at a rate that captures the dynamics of the plant and which is often much lower than the rate that can be communicated. This setting offers the opportunity of improving the system performance by employing multiple channel uses to convey a single message (output plant observation or control input). Common ways of doing so are through either repeating the message, or by quantizing it to a number of bits and then transmitting a channel coded version of the bits whose length is commensurate with the number of channel uses per sampled message. We argue that such “separated source and channel coding” can be suboptimal and propose to perform joint source-channel coding. Since the block length is short we obviate the need to go to the digital domain altogether and instead consider analog joint source-channel coding. For the case where the communication signaling rate is twice the sampling rate, we employ the Archimedean bi-spiral-based Shannon-Kotel'nikov analog maps to show significant improvement in stability margins and linear-quadratic Gaussian (LQG) costs over simple schemes that employ repetition.

Multi-rate control over AWGN channels via analog joint source-channel coding

KAUST Repository

Khina, Anatoly

2017-01-05

We consider the problem of controlling an unstable plant over an additive white Gaussian noise (AWGN) channel with a transmit power constraint, where the signaling rate of communication is larger than the sampling rate (for generating observations and applying control inputs) of the underlying plant. Such a situation is quite common since sampling is done at a rate that captures the dynamics of the plant and which is often much lower than the rate that can be communicated. This setting offers the opportunity of improving the system performance by employing multiple channel uses to convey a single message (output plant observation or control input). Common ways of doing so are through either repeating the message, or by quantizing it to a number of bits and then transmitting a channel coded version of the bits whose length is commensurate with the number of channel uses per sampled message. We argue that such “separated source and channel coding” can be suboptimal and propose to perform joint source-channel coding. Since the block length is short we obviate the need to go to the digital domain altogether and instead consider analog joint source-channel coding. For the case where the communication signaling rate is twice the sampling rate, we employ the Archimedean bi-spiral-based Shannon-Kotel\\'nikov analog maps to show significant improvement in stability margins and linear-quadratic Gaussian (LQG) costs over simple schemes that employ repetition.

Modeling, analysis, and design of stationary reference frame droop controlled parallel three-phase voltage source inverters

DEFF Research Database (Denmark)

Vasquez, Juan Carlos; Guerrero, Josep M.; Savaghebi, Mehdi

2013-01-01

Power electronics based MicroGrids consist of a number of voltage source inverters (VSIs) operating in parallel. In this paper, the modeling, control design, and stability analysis of parallel connected three-phase VSIs are derived. The proposed voltage and current inner control loops and the mat......Power electronics based MicroGrids consist of a number of voltage source inverters (VSIs) operating in parallel. In this paper, the modeling, control design, and stability analysis of parallel connected three-phase VSIs are derived. The proposed voltage and current inner control loops...... control restores the frequency and amplitude deviations produced by the primary control. Also, a synchronization algorithm is presented in order to connect the MicroGrid to the grid. Experimental results are provided to validate the performance and robustness of the parallel VSI system control...

A Survey on Open-Source Flight Control Platforms of Unmanned Aerial Vehicle

DEFF Research Database (Denmark)

Ebeid, Emad Samuel Malki; Skriver, Martin; Jin, Jie

2017-01-01

Recently, Unmanned Aerial Vehicle (UAV), so-called drones, have gotten a lot of attention in academic research and commercial applications due to their simple structure, ease of operations and low-cost hardware components. Flight controller, embedded electronics component, represents the core part...... of the drone. It aims at performing the main operations of the drone (e.g., autonomous control and navigation). There are various types of flight controllers and each of them has its own characteristics and features. This paper presents an extensive survey on the publicly available open-source flight...

Predicting nonpoint stormwater runoff quality from land use

Science.gov (United States)

2018-01-01

Evaluating the impact of urban development on natural ecosystem processes has become an increasingly complex task for planners, environmental scientists, and engineers. As the built environment continues to grow, unregulated nonpoint pollutants from increased human activity and large-scale development severely stress urban streams and lakes resulting in their currently impaired or degraded state. In response, integrated water quality management programs have been adopted to address these unregulated nonpoint pollutants by utilizing best management practices (BMPs) that treat runoff as close to the source as possible. Knowing where to install effective BMPs is no trivial task, considering budget constraints and the spatially extensive nature of nonpoint stormwater runoff. Accordingly, this paper presents an initial, straightforward and cost-effective methodology to identify critical nonpoint pollutant source watersheds through correlation of water quality with land use. Through an illustrative application to metropolitan Denver, Colorado, it is shown how this method can be used to aid stormwater professionals to evaluate and specify retrofit locations in need of water quality treatment features reduce, capture and treat stormwater runoff prior to entering receiving waters. PMID:29742172

Analysis of the environmental behavior of farmers for non-point source pollution control and management in a water source protection area in China.

Science.gov (United States)

Wang, Yandong; Yang, Jun; Liang, Jiping; Qiang, Yanfang; Fang, Shanqi; Gao, Minxue; Fan, Xiaoyu; Yang, Gaihe; Zhang, Baowen; Feng, Yongzhong

2018-08-15

The environmental behavior of farmers plays an important role in exploring the causes of non-point source pollution and taking scientific control and management measures. Based on the theory of planned behavior (TPB), the present study investigated the environmental behavior of farmers in the Water Source Area of the Middle Route of the South-to-North Water Diversion Project in China. Results showed that TPB could explain farmers' environmental behavior (SMC=0.26) and intention (SMC=0.36) well. Furthermore, the farmers' attitude towards behavior (AB), subjective norm (SN), and perceived behavioral control (PBC) positively and significantly influenced their environmental intention; their environmental intention further impacted their behavior. SN was proved to be the main key factor indirectly influencing the farmers' environmental behavior, while PBC had no significant and direct effect. Moreover, environmental knowledge following as a moderator, gender and age was used as control variables to conduct the environmental knowledge on TPB construct moderated mediation analysis. It demonstrated that gender had a significant controlling effect on environmental behavior; that is, males engage in more environmentally friendly behaviors. However, age showed a significant negative controlling effect on pro-environmental intention and an opposite effect on pro-environmental behavior. In addition, environmental knowledge could negatively moderate the relationship between PBC and environmental intention. PBC had a greater impact on the environmental intention of farmers with poor environmental knowledge, compared to those with plenty environmental knowledge. Altogether, the present study could provide a theoretical basis for non-point source pollution control and management. Copyright © 2018 Elsevier B.V. All rights reserved.

FEL polarization control studies on Dalian coherent light source

International Nuclear Information System (INIS)

Zhang Tong; Deng Haixiao; Wang Dong; Zhao Zhentang; Zhang Weiqing; Wu Guorong; Dai Dongxu; Yang Xueming

2013-01-01

The polarization switch of a free-electron laser (FEL) is of great importance to the user scientific community. In this paper, we investigate the generation of controllable polarization FEL from two well-known approaches for Dalian coherent light source, i.e., crossed planar undulator and elliptical permanent undulator. In order to perform a fair comparative study, a one-dimensional time-dependent FEL code has been developed, in which the imperfection effects of an elliptical permanent undulator are taken into account. Comprehensive simulation results indicate that the residual beam energy chirp and the intrinsic FEL gain may contribute to the degradation of the polarization performance for the crossed planar undulator. The elliptical permanent undulator is not very sensitive to the undulator errors and beam imperfections. Meanwhile, with proper configurations of the main planar undulators and additional elliptical permanent undulator section, circular polarized FEL with pulse energy exceeding 100 μJ could be achieved at Dalian coherent light source. (authors)

Regulatory control and challenges in Medical facilities using ionising radiation sources

International Nuclear Information System (INIS)

Agarwal, S.P.

2008-01-01

Medical facilities utilising ionising radiation sources for diagnostic and treatment of cancer are regulated under the provisions of Atomic Energy (Radiation Protection) Rules, 2004 promulgated under the Atomic Energy Act 1962. The Competent Authority for the enforcement of the rules is Chairman, Atomic Energy Regulatory Board (AERB). Practice specific codes are issued by AERB for medical facilities such as Radiotherapy, Nuclear Medicine and Radiology. Regulatory process for control of medical facilities covers the entire life cycle of the radiation sources in three stages viz pre-Iicensing, during useful life and decommissioning and disposal. Pre-Iicensing requirements include use of type approved sources and equipment, approval of design layout of the facility and installation, exclusive (safe and secure) source storage facility when the equipment is not in use, radiation (area/individual) monitoring devices, qualified, trained and certified manpower, emergency response plans and commitment from the licensee for the safe disposal of disused/decayed sources. Compliance to these requirements makes the applicant eligible to obtain license from AERB for the operation of the medical facility. During the use of radiation sources, specific prior approval of the Competent Authority is required in respect of every source replacement, sale, transfer, transport, import and export. Further, all licensees are required to send the periodic safety Status reports to AERB as well as reporting of any off normal events. AERB conducts inspection of the facilities to ensure compliance with the safety requirements during operation of the facility. Violation of safety norms by licensee attracts enforcement action which includes suspension, modification or withdrawal of licensee for operation of the facility. Upon completion of the useful life of the source, the licensee decommissions the facility and returns the source to the original supplier. For returning the source, prior

PM10 standards and nontraditional particulate source controls: Research perspective

International Nuclear Information System (INIS)

Watson, J.G.

1992-01-01

Knowledge of how to measure suspended particles, what their concentrations are, what they are composed of, and where they come from has increased substantially since 1975. At that time, much of the pioneering work in these areas was just being conducted and published. Size-classified measurements, low-level elemental analysis, inorganic ion analysis, and carbon determinations for aerosol samples were novel research developments. Receptor modeling was not considered to be a scientific discipline, let alone a useful tool for source apportionment. Presentations at earlier conferences went to great lengths to document and justify methodologies which are taken for granted at this conference. This paper goes on to discuss research findings in control of wood smoke, fugitive dusts, motor vehicle exhausts, and secondary aerosols. Research results in source apportionment are also discussed

The Use of LiDAR Elevation Data and Satellite Imagery to Locate Critical Source Areas to Diffuse Pollution in Agricultural Watersheds

Science.gov (United States)

Drouin, Ariane; Michaud, Aubert; Thériault, Georges; Beaudin, Isabelle; Rodrigue, Jean-François; Denault, Jean-Thomas; Desjardins, Jacques; Côté, Noémi

2013-04-01

more humid. A variety of other indices are used to explain the sediments yields. These indices, such as the average percentage of slope, the distance to the stream, the relative position in landscape, the position to the water table, etc. are mainly derived from high precision elevation data. All these data are used to locate critical source areas that generally correspond to a restraint part of the territory but account for the principal amount of sediments exports. Once the critical source areas are identified, best management practices (BMPs) (per example : contaminant source control practices, conservation cropping practices and surface runoff control structures) can be planned. This way, money and energy are used where it really counts. In this presentation, the complete methodology including LiDAR data processing will be explained. The results and the possibility to reproduce the developed method will be discussed.

Comparing the Selection and Placement of Best Management Practices in Improving Water Quality Using a Multiobjective Optimization and Targeting Method

Directory of Open Access Journals (Sweden)

Li-Chi Chiang

2014-03-01

Full Text Available Suites of Best Management Practices (BMPs are usually selected to be economically and environmentally efficient in reducing nonpoint source (NPS pollutants from agricultural areas in a watershed. The objective of this research was to compare the selection and placement of BMPs in a pasture-dominated watershed using multiobjective optimization and targeting methods. Two objective functions were used in the optimization process, which minimize pollutant losses and the BMP placement areas. The optimization tool was an integration of a multi-objective genetic algorithm (GA and a watershed model (Soil and Water Assessment Tool—SWAT. For the targeting method, an optimum BMP option was implemented in critical areas in the watershed that contribute the greatest pollutant losses. A total of 171 BMP combinations, which consist of grazing management, vegetated filter strips (VFS, and poultry litter applications were considered. The results showed that the optimization is less effective when vegetated filter strips (VFS are not considered, and it requires much longer computation times than the targeting method to search for optimum BMPs. Although the targeting method is effective in selecting and placing an optimum BMP, larger areas are needed for BMP implementation to achieve the same pollutant reductions as the optimization method.

Generic inertia emulation controller for multi-terminal voltage-source-converter high voltage direct current systems

DEFF Research Database (Denmark)

Zhu, Jiebei; Guerrero, Josep M.; Hung, William

2014-01-01

A generic Inertia Emulation Controller (INEC) scheme for Multi-Terminal Voltage-Source-Converter based HVDC (VSC-MTDC) systems is proposed and presented in this paper. The proposed INEC can be incorporated in any Grid-side Voltage-Source-Converter (GVSC) station, allowing the MTDC terminal...

Active and reactive power control of a current-source PWM-rectifier using space vectors

Energy Technology Data Exchange (ETDEWEB)

Salo, M.; Tuusa, H. [Tampere University of Technology (Finland). Department of Electrical Engineering, Power Electronics

1997-12-31

In this paper the current-source PWM-rectifier with active and reactive power control is presented. The control system is realized using space vector methods. Also, compensation of the reactive power drawn by the line filter is discussed. Some simulation results are shown. (orig.) 8 refs.

The scope and control of attention: Sources of variance in working memory capacity.

Science.gov (United States)

Chow, Michael; Conway, Andrew R A

2015-04-01

Working memory capacity is a strong positive predictor of many cognitive abilities, across various domains. The pattern of positive correlations across domains has been interpreted as evidence for a unitary source of inter-individual differences in behavior. However, recent work suggests that there are multiple sources of variance contributing to working memory capacity. The current study (N = 71) investigates individual differences in the scope and control of attention, in addition to the number and resolution of items maintained in working memory. Latent variable analyses indicate that the scope and control of attention reflect independent sources of variance and each account for unique variance in general intelligence. Also, estimates of the number of items maintained in working memory are consistent across tasks and related to general intelligence whereas estimates of resolution are task-dependent and not predictive of intelligence. These results provide insight into the structure of working memory, as well as intelligence, and raise new questions about the distinction between number and resolution in visual short-term memory.

Passivity-Based Control applied to DC hybrid power source using fuel cell and supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Ayad, M.Y.; Wack, M.; Laghrouche, S. [SeT, UTBM, Belfort (cedex) 90010 (France); Becherif, M. [SeT, UTBM, Belfort (cedex) 90010 (France); FC-Lab, UTBM, Belfort (cedex) 90010 (France); Henni, A. [Alstom Power System, Energy Management Business, Alstom (France); Aboubou, A. [LMSE Laboratory, Biskra University, 07000 (Algeria)

2010-07-15

Nowadays, energy management becomes an absolute necessity. To reduce systems consumption, the idea is to recover energy when it is possible and to reuse it when the system is in need. Energy can be saved in peak power unit (electric double layer capacitors called supercapacitors). Those latter can absorb or supply power peaks. This paper deals with the conception of hybrid power sources using fuel cell as main source, a DC link and supercapacitors as transient power source. The whole system is modeled in state space equations. The energy management is reached using Passivity-Based Control (PBC). PBC is a very powerful nonlinear technique dealing with important system information like the system's total energy. Stability proof and simulation results are given. In this proposed control laws only few measurement are needed (two or three depending on the presented solutions one or two). (author)

Self-optimizing control of air-source heat pump with multivariable extremum seeking

International Nuclear Information System (INIS)

Dong, Liujia; Li, Yaoyu; Mu, Baojie; Xiao, Yan

2015-01-01

The air-source heat pump (ASHP) is widely adopted for cooling and heating of residential and commercial buildings. The performance of ASHP can be controlled by several operating variables, such as compressor capacity, condenser fan speed, evaporator fan speed and suction superheat. In practice, the system characteristics can be varied significantly by the variations in ambient condition, operation setpoint, internal thermal load and equipment degradation, which makes it difficult to obtain accurate plant models. As consequence, the model based control strategies for ASHP could limit the achievable energy efficiency. Model-free self-optimizing control strategies are thus more preferable. In this study, a multi-input extremum seeking control (ESC) scheme is proposed for both heating and cooling operation of ASHP. The zone temperature is assumed to be regulated by the compressor capacity, while the expansion valve opening is used to regulate the suction superheat at the given setpoint. The total power consumption of the compressor, the condenser fan and the evaporator fan is measured as input to the ESC, while the ESC controls the evaporator fan speed, the condenser fan speed and the suction superheat setpoint. The proposed scheme is evaluated with a Modelica based dynamic simulation model of ASHP under both cooling and heating modes of operation. Simulation results show the effectiveness of the proposed scheme to achieve the maximum achievable efficiency in a nearly model-free manner. - Highlights: • Multi-input ESC. • Air-source heat pump. • Cooling and heating. • Modelica based model

Decentralized and Real-Time Power Dispatch Control for an Islanded Microgrid Supported by Distributed Power Sources

Directory of Open Access Journals (Sweden)

Changsun Ahn

2013-12-01

Full Text Available Microgrids can deploy traditional and/or renewable power sources to support remote sites. Utilizing renewable power sources requires more complicated control strategies to achieve acceptable power quality and maintain grid stability. In this research, we assume that the grid stability problem is already solved. As a next step, we focus on how the power can be dispatched from multiple power sources for improved grid efficiency. Isolated microgrids frequently require reconfigurations because of the grid expansion or component failures. Therefore, the control strategies ideally should be implemented in a plug-and-play fashion. Moreover, these strategies ideally require no pre-knowledge of the grid structure, and as little communication with neighboring power sources as possible. The control objective is to minimize a cost function that can be adjusted to reflect the desire to minimize energy cost and/or losses. An algorithm is designed to satisfy a derived necessary condition of function optimality. Such conditions are obtained by formulating Lagrange functions. An equivalent grid model approximates the grid structure which was later confirmed to represent the grid behavior adequately. For decentralized operations, we execute the distributed control sequentially using a simple token communication protocol. The performance of the combined system identification-Lagrange function minimization algorithm is demonstrated through simulations.

Control of emissions from stationary combustion sources: Pollutant detection and behavior in the atmosphere

International Nuclear Information System (INIS)

Licht, W.; Engel, A.J.; Slater, S.M.

1979-01-01

Stationary combustion resources continue to be significant sources of NOx and SOx pollutants in the ambient atmosphere. This volume considers four problem areas: (1) control of emissions from stationary combustion sources, particularly SOx and NOx (2) pollutant behavior in the atmosphere (3) advances in air pollution analysis and (4) air quality management. Topics of interest include carbon slurries for sulfur dioxide abatement, mass transfer in the Kellogg-Weir air quality control system, oxidation/inhibition of sulfite ion in aqueous solution, some micrometeorological methods of measuring dry deposition rates, Spanish moss as an indicator of airborne metal contamination, and air quality impacts from future electric power generation in Texas

Spark-protected ion-source control and monitoring system at 1.5 MV

International Nuclear Information System (INIS)

Bogaty, J.M.; Zolecki, R.

1981-01-01

The Heavy Ion Fusion Program at Argonne National Laboratory utilizes a 1.5-MV Xe ion preaccelerator. Reliable beam transport requires accurate measurements and precise control of various ion-source parameters. This paper discusses the use of a multiplexed fiberoptic data-transmission system and low-cost digital stepper motors for control functions. Techniques are discussed which allow TTL and CMOS semiconductor curcuits to survive the destructive sparks which can occur in the 1.5-MV preaccelerator

National policy for control of radioactive sources and radioactive waste from non-power applications in Lithuania

International Nuclear Information System (INIS)

Klevinskas, G.; Mastauskas, A.

2001-01-01

According to the Law on Radiation Protection of the Republic of Lithuania (passed in 1999), the Radiation Protection Centre of the Ministry of Health is the regulatory authority responsible for the radiation protection of public and of workers using sources of ionizing radiation in Lithuania. One of its responsibilities is the control of radioactive sources from the beginning of their 'life cycle', when they are imported in, used, transported and placed as spent into the radioactive waste storage facilities. For the effective control of sources there is national authorization system (notification- registration-licensing) based on the international requirements and recommendations introduced, which also includes keeping and maintaining the Register of Sources, controlling and investigating events while illegally carrying on or in possession of radioactive material, decision making and performing the state radiation protection supervision and control of users of radioactive sources, controlling, within the limits of competence, the radioactive waste management activities in nuclear and non-nuclear power applications. According to the requirements set out in the Law on Radiation Protection and the Government Resolution 'On Establishment of the State Register of the Sources of Ionizing Radiation and Exposure of Workers' (1999) and supplementary legal acts, all licence-holders conducting their activities with sources of ionizing radiation have to present all necessary data to the State Register after annual inventory of sources, after installation of new sources, after decommissioning of sources, after disposal of spent sources, after finishing the activities with the generators of ionizing radiation. The information to the Radiation Protection Centre has to be presented every week from the Customs Department of the Ministry of Finance about all sources of ionizing radiation imported to or exported from Lithuania and the information about the companies performed these

Research on control technology of hardware parallelism for marine controlled source electromagnetic transmitter

Science.gov (United States)

Wang, Meng; Deng, Ming; Luo, Xianhu; Zhao, Qingxian; Chen, Kai; Jing, Jianen

2018-02-01

The marine controlled source electromagnetic (CSEM) method has been recognized as an effective exploration method of shallow hydrocarbons around the world. We developed our own underwater marine CSEM transmitter that consisted of many functional modules with various response times. We previously adopted a centralized software-control technology to design the transmitter circuit topological structure. That structure probably generated a control disorder or malfunction. These undesirable conditions could lead to repeated recovery and deployment of the transmitter, which not only consumed time but also affected data continuity and establishment of stable and continuous CSEM field. We developed an instrument design concept named ‘control technology of hardware parallelism’. In this design, a noteworthy innovation of our new technology is to solve the above-mentioned problems at the physical and fundamental levels. We used several self-contained control-units to simultaneously accomplish the predetermined functions of the transmitter. The new solution relies on two technologies: multi-core embedded technology and multi-channel parallel optical-fiber data transmission technology. The first technology depends on many independent microcontrollers. Every microcontroller is only used to achieve a customized function. The second one relies on several multiple optical-fiber transmission channels realized by a complex programmable logic device and two optical-fiber conversion devices, which are used to establish a communication link between the shipboard monitoring and control-unit and underwater transmitter. We have conducted some marine experiments to verify the reliability and stability of the new method. In particular, the new technology used in the transmitter system could help us obtain more useful measured data in a limited time, improve real-time efficiency, and support the establishment of a stable CSEM field.

Design and construction of the advanced photon source 352-MHz rf system switching control

International Nuclear Information System (INIS)

Horan, D.; Solita, L.; Reigle, D.; Dimonte, N.

1997-01-01

A switching control system has been designed and built to provide the capability of rapidly switching the waveguide and low-level cabling between different klystrons to operate the Advanced Photon Source storage ring in the event of a failure of a klystron system or to perform necessary repairs and preventative maintenance. The twelve possible modes of operation allow for complete redundancy of the booster synchrotron rf system and either a maximum of two storage ring rf systems to be completely off-line or one system to be used as a power source for an rf test stand. A programmable controller is used to send commands to intermediate control panels which interface to WR2300 waveguide switches and phase shifters, rf cavity interlock and low-level rf distribution systems, and klystron power supply controls for rapid reconfiguration of the rf systems in response to a mode-selection command. Mode selection is a local manual operation using a keyswitch arrangement which prevents more than one mode from being selected at a time. The programmable controller also monitors for hardware malfunction and guards against open-quotes hot-switchingclose quotes of the rf systems. The rf switching controls system is monitored via the Experimental Physics and Industrial Control System (EPICS) for remote system status check

Environmental Nitrogen Losses from Commercial Crop Production Systems in the Suwannee River Basin of Florida.

Science.gov (United States)

Prasad, Rishi; Hochmuth, George J

2016-01-01

The springs and the Suwannee river of northern Florida in Middle Suwanee River Basin (MSRB) are among several examples in this planet that have shown a temporal trend of increasing nitrate concentration primarily due to the impacts of non-point sources such as agriculture. The rate of nitrate increase in the river as documented by Ham and Hatzell (1996) was 0.02 mg N L-1 y-1. Best management practices (BMPs) for nutrients were adopted by the commercial farms in the MSRB region to reduce the amounts of pollutants entering the water bodies, however the effectiveness of BMPs remains a topic of interest and discussion among the researchers, environmental administrators and policy makers about the loads of nitrogen entering into groundwater and river systems. Through this study, an initiative was taken to estimate nitrogen losses into the environment from commercial production systems of row and vegetable crops that had adopted BMPs and were under a presumption of compliance with state water quality standards. Nitrogen mass budget was constructed by quantifying the N sources and sinks for three crops (potato (Solanum tuberosum L.), sweet corn (Zea mays L.) and silage corn (Zea mays L.)) over a four year period (2010-2013) on a large representative commercial farm in northern Florida. Fertilizer N was found to be the primary N input and represented 98.0 ± 1.4, 91.0 ± 13.9, 78.0 ± 17.3% of the total N input for potato, sweet corn, and silage corn, respectively. Average crop N uptake represented 55.5%, 60.5%, and 65.2% of the mean total input N whereas average mineral N left in top 0.3 m soil layer at harvest represented 9.1%, 4.5%, and 2.6% of the mean total input N. Mean environmental N losses represented 35.3%, 34.3%, and 32.7% of the mean total input N for potato, sweet corn, and silage corn, respectively. Nitrogen losses showed a linear trend with increase in N inputs. Although, there is no quick fix for controlling N losses from crop production in MSRB, the

Scrap supply in Bosnian after war situation - sources, quality, regulation and control

International Nuclear Information System (INIS)

Pihura, Dervis

1999-01-01

Before the war, the Bosnian foundry and steel industry were supplied with scrap partly from domestic sources but mainly from foreign market. The annual steel production before the war recorded 130,000 tonnes of casting and 2,000.000 tonnes of crude steel. Most of the scrap was imported to secure and stabilize the production. During and after the war, despite a significant loss of production, efforts have been made to return to the normal production level in many ways. In the wake of the war, there has been a growing concern over the import of radioactive contaminated metallurgical scrap or low quality raw materials which are uncontrolled or of unidentified sources. In this regard, it is urgently required to establish an effective system to prevent from, to detect and to control the flow of the radioactive contaminated metallurgical scrap. The system should be established in such a way that all sorts of radioactive metallurgical elements should be controlled and prevented from use in all the metallurgical manufacturing processes, ferrous and non-ferrous alike. The coverage of control should start from the border or (air) port checkpoint where the flow of the scrap begins to the final steel product. The control system should take a form of internationally common and acceptable standards and regulations. Equipments and measurement techniques should also be internationally common. (author)

Force analysis of the advanced neutron source control rod drive latch mechanism

International Nuclear Information System (INIS)

Damiano, B.

1989-01-01

The Advanced Neutron Source reactor (ANS), a proposed Department of Energy research reactor currently undergoing conceptual design at the Oak Ridge National Laboratory (ORNL), will generate a thermal neutron flux approximating 10 30 M -2 emdash S -1 . The compact core necessary to produce this flux provides little space for the shim safety control rods, which are located in the central annulus of the core. Without proper control rod drive design, the control rod drive magnets (which hold the control rod latch in a ready-to-scram position) may be unable to support the required load due to their restricted size. This paper describes the force analysis performed on the control rod latch mechanism to determine the fraction of control rod weight transferred to the drive magnet. This information will be useful during latch, control rod drive and magnet design. 5 refs., 12 figs

Principles for the exemption of radiation sources and practices from regulatory control

International Nuclear Information System (INIS)

1988-01-01

Radiation sources, including equipment and installations, which emit ionizing radiations, are potentially harmful to health and their use should therefore be regulated. Some types of radiation source, however, do not need to be subject to regulatory control, because they present such a low hazard that it would be a needless waste of time and effort to exercise control by a regulatory process and they can therefore be exempted from it. An Advisory Group Meeting was convened in Vienna in March 1988 sponsored jointly by the IAEA and NEA. This Safety Guide is the result of that meeting and represents a first international consensus on the subject of exemption principles. This document is issued as an IAEA Safety Guide since it recommends a procedure which might be followed in implementing the Basic Safety Standards (BSS) for Radiation Protection. Its purpose is to recommend a policy on exemptions from the BSS system of notification, registration and licensing. 15 refs

An Improved Current-Doubler Rectifier for the Marine Controlled Source Electromagnetic Transmitter

Directory of Open Access Journals (Sweden)

Hongxi Song

2018-01-01

Full Text Available High power marine controlled source electromagnetic transmitters have gained interest with applications in marine geological survey and mineral resources exploration. The direct current to direct current (DC-DC converter that is typically used in marine transmitters has some issues, as the insulated-gate bipolar transistor (IGBT tube cannot achieve zero-voltage switching (ZVS. In particular, lagging-leg switching cannot easily achieve ZVS. The conversion efficiency of the heat converter requires improvement. This paper proposes an improved current-doubler rectifier for the marine controlled source electromagnetic transmitter (ICDR-MCSET. Resonant inductance is increased and a blocking capacitor is added to the converter (DC-DC circuit, where the converter can achieve ZVS in a wide load range. This results in the effective decrease of the heating temperature and the improvement of transformation efficiency. Saber software simulation and a 20 KW electromagnetic transmitter are used to verify the results, which show that the method is feasible and effective.

Early Versus Delayed Source Control in Open Abdomen Management for Severe Intra-abdominal Infections: A Retrospective Analysis on 111 Cases.

Science.gov (United States)

Rausei, Stefano; Pappalardo, Vincenzo; Ruspi, Laura; Colella, Antonio; Giudici, Simone; Ardita, Vincenzo; Frattini, Francesco; Rovera, Francesca; Boni, Luigi; Dionigi, Gianlorenzo

2018-03-01

Time to source control plays a determinant prognostic role in patients having severe intra-abdominal infections (IAIs). Open abdomen (OA) management became an effective treatment option for peritonitis. Aim of this study was to analyze the correlation between time to source control and outcome in patients presenting with abdominal sepsis and treated by OA. We retrospectively analyzed 111 patients affected by abdominal sepsis and treated with OA from May 2007 to May 2015. Patients were classified according to time interval from first patient evaluation to source control. The end points were intra-hospital mortality and primary fascial closure rate. The in-hospital mortality rate was 21.6% (24/111), and the primary fascial closure rate was 90.9% (101/111). A time to source control ≥6 h resulted significantly associated with a poor prognosis and a lower fascial closure rate (mortality 27.0 vs 9.0%, p = 0.04; primary fascial closure 86 vs 100%, p = 0.02). We observed a direct increase in mortality (and a reduction in closure rate) for each 6-h delay in surgery to source control. Early source control using OA management significantly improves outcome of patients with severe IAIs. This damage control approach well fits to the treatment of time-related conditions, particularly in case of critically ill patients.

Monitoring Hydraulic Fracturing Using Ground-Based Controlled Source Electromagnetics

Science.gov (United States)

Hickey, M. S.; Trevino, S., III; Everett, M. E.

2017-12-01

Hydraulic fracturing allows hydrocarbon production in low permeability formations. Imaging the distribution of fluid used to create a hydraulic fracture can aid in the characterization of fracture properties such as extent of plume penetration as well as fracture azimuth and symmetry. This could contribute to improving the efficiency of an operation, for example, in helping to determine ideal well spacing or the need to refracture a zone. A ground-based controlled-source electromagnetics (CSEM) technique is ideal for imaging the fluid due to the change in field caused by the difference in the conductive properties of the fluid when compared to the background. With advances in high signal to noise recording equipment, coupled with a high-power, broadband transmitter we can show hydraulic fracture extent and azimuth with minimal processing. A 3D finite element code is used to model the complete well casing along with the layered subsurface. This forward model is used to optimize the survey design and isolate the band of frequencies with the best response. In the field, the results of the modeling are also used to create a custom pseudorandom numeric (PRN) code to control the frequencies transmitted through a grounded dipole source. The receivers record the surface voltage across two grounded dipoles, one parallel and one perpendicular to the transmitter. The data are presented as the displays of amplitude ratios across several frequencies with the associated spatial information. In this presentation, we show multiple field results in multiple basins in the United States along with the CSEM theory used to create the survey designs.

The development of control processes supporting source memory discrimination as revealed by event-related potentials.

Science.gov (United States)

de Chastelaine, Marianne; Friedman, David; Cycowicz, Yael M

2007-08-01

Improvement in source memory performance throughout childhood is thought to be mediated by the development of executive control. As postretrieval control processes may be better time-locked to the recognition response rather than the retrieval cue, the development of processes underlying source memory was investigated with both stimulus- and response-locked event-related potentials (ERPs). These were recorded in children, adolescents, and adults during a recognition memory exclusion task. Green- and red-outlined pictures were studied, but were tested in black outline. The test requirement was to endorse old items shown in one study color ("targets") and to reject new items along with old items shown in the alternative study color ("nontargets"). Source memory improved with age. All age groups retrieved target and nontarget memories as reflected by reliable parietal episodic memory (EM) effects, a stimulus-locked ERP correlate of recollection. Response-locked ERPs to targets and nontargets diverged in all groups prior to the response, although this occurred at an increasingly earlier time point with age. We suggest these findings reflect the implementation of attentional control mechanisms to enhance target memories and facilitate response selection with the greatest and least success, respectively, in adults and children. In adults only, response-locked ERPs revealed an early-onsetting parietal negativity for nontargets, but not for targets. This was suggested to reflect adults' ability to consistently inhibit prepotent target responses for nontargets. The findings support the notion that the development of source memory relies on the maturation of control processes that serve to enhance accurate selection of task-relevant memories.

Regulatory Control of Radiation Sources. Safety Guide

International Nuclear Information System (INIS)

2009-01-01

This Safety Guide is intended to assist States in implementing the requirements established in Safety Standards Series No. GS-R-1, Legal and Governmental Infrastructure for Nuclear, Radiation, Radioactive Waste and Transport Safety, for a national regulatory infrastructure to regulate any practice involving radiation sources in medicine, industry, research, agriculture and education. The Safety Guide provides advice on the legislative basis for establishing regulatory bodies, including the effective independence of the regulatory body. It also provides guidance on implementing the functions and activities of regulatory bodies: the development of regulations and guides on radiation safety; implementation of a system for notification and authorization; carrying out regulatory inspections; taking necessary enforcement actions; and investigating accidents and circumstances potentially giving rise to accidents. The various aspects relating to the regulatory control of consumer products are explained, including justification, optimization of exposure, safety assessment and authorization. Guidance is also provided on the organization and staffing of regulatory bodies. Contents: 1. Introduction; 2. Legal framework for a regulatory infrastructure; 3. Principal functions and activities of the regulatory body; 4. Regulatory control of the supply of consumer products; 5. Functions of the regulatory body shared with other governmental agencies; 6. Organization and staffing of the regulatory body; 7. Documentation of the functions and activities of the regulatory body; 8. Support services; 9. Quality management for the regulatory system.

Bone morphogenetic protein-induced heterotopic bone formation: What have we learned from the history of a half century?

Directory of Open Access Journals (Sweden)

Takenobu Katagiri, PhD

2015-05-01

Full Text Available Bone morphogenetic protein (BMP was originally discovered by Marshall Urist a half century ago following the observation of a unique activity that induced heterotopic bone formation in skeletal muscle tissue. The molecular mechanisms underlying the induction of heterotopic bone formation in skeletal muscle by BMPs were elucidated through the purification and molecular cloning of BMPs and identification of their functional receptors and downstream effectors, as well as from genetic disorders related to BMP activity. BMPs are important regulators of not only skeletal development and regeneration but also the homeostasis of normal skeletal muscle mass. There is still much to learn about the physiology and pathology at the interface of BMPs and skeletal muscle.

Development and operation of a computerized source controller for a gamma calibration well

International Nuclear Information System (INIS)

Halliburton, R.E.

1986-01-01

In the 1950s, the need for an accurately reproducible, real-time gamma calibration facility at the Oak Ridge National Laboratory (ORNL) was met with a manually operated radium source housed in a calibration well. This arrangement was quite satisfactory in the early days but was not able to keep pace with the increasing number of instruments necessary to support an expanding health physics program. Consequently, the hand crank was replaced by an electric motor in the early 1960s. This improvement made it possible to move the source at speeds up to 7 cm/s, resulting in a major increase in efficiency. This configuration served reliably for two decades but, by the 1980s, component aging and the growing scarcity of replacement parts led to the development of a third-generation source controller. The electric motor and vacuum-tube-driven power supply were replaced with a solid state power supply and a stepper motor interfaced to a microcomputer. The software written to operate the system is menu-driven, user-friendly, and provides the greatest flexibility and ease of use while minimizing learning time. The development and use of this control system will be discussed

Digital Control Techniques Based on Voltage Source Inverters in Renewable Energy Applications: A Review

Directory of Open Access Journals (Sweden)

Sohaib Tahir

2018-02-01

Full Text Available In the modern era, distributed generation is considered as an alternative source for power generation. Especially, need of the time is to provide the three-phase loads with smooth sinusoidal voltages having fixed frequency and amplitude. A common solution is the integration of power electronics converters in the systems for connecting distributed generation systems to the stand-alone loads. Thus, the presence of suitable control techniques, in the power electronic converters, for robust stability, abrupt response, optimal tracking ability and error eradication are inevitable. A comprehensive review based on design, analysis, validation of the most suitable digital control techniques and the options available for the researchers for improving the power quality is presented in this paper with their pros and cons. Comparisons based on the cost, schemes, performance, modulation techniques and coordinates system are also presented. Finally, the paper describes the performance evaluation of the control schemes on a voltage source inverter (VSI and proposes the different aspects to be considered for selecting a power electronics inverter topology, reference frames, filters, as well as control strategy.

Parsing pyrogenic polycyclic aromatic hydrocarbons: forensic chemistry, receptor models, and source control policy.

Science.gov (United States)

O'Reilly, Kirk T; Pietari, Jaana; Boehm, Paul D

2014-04-01

A realistic understanding of contaminant sources is required to set appropriate control policy. Forensic chemical methods can be powerful tools in source characterization and identification, but they require a multiple-lines-of-evidence approach. Atmospheric receptor models, such as the US Environmental Protection Agency (USEPA)'s chemical mass balance (CMB), are increasingly being used to evaluate sources of pyrogenic polycyclic aromatic hydrocarbons (PAHs) in sediments. This paper describes the assumptions underlying receptor models and discusses challenges in complying with these assumptions in practice. Given the variability within, and the similarity among, pyrogenic PAH source types, model outputs are sensitive to specific inputs, and parsing among some source types may not be possible. Although still useful for identifying potential sources, the technical specialist applying these methods must describe both the results and their inherent uncertainties in a way that is understandable to nontechnical policy makers. The authors present an example case study concerning an investigation of a class of parking-lot sealers as a significant source of PAHs in urban sediment. Principal component analysis is used to evaluate published CMB model inputs and outputs. Targeted analyses of 2 areas where bans have been implemented are included. The results do not support the claim that parking-lot sealers are a significant source of PAHs in urban sediments. © 2013 SETAC.

Mixed Waste Management Facility (MWMF) Old Burial Ground (OBG) source control technology and inventory study

Energy Technology Data Exchange (ETDEWEB)

Flach, G.P.; Rehder, T.E.; Kanzleiter, J.P.

1996-10-02

This report has been developed to support information needs for wastes buried in the Burial Ground Complex. Information discussed is presented in a total of four individual attachments. The general focus of this report is to collect information on estimated source inventories, leaching studies, source control technologies, and to provide information on modeling parameters and associated data deficiencies.

Mixed Waste Management Facility (MWMF) Old Burial Ground (OBG) source control technology and inventory study

International Nuclear Information System (INIS)

Flach, G.P.; Rehder, T.E.; Kanzleiter, J.P.

1996-01-01

This report has been developed to support information needs for wastes buried in the Burial Ground Complex. Information discussed is presented in a total of four individual attachments. The general focus of this report is to collect information on estimated source inventories, leaching studies, source control technologies, and to provide information on modeling parameters and associated data deficiencies

Storm Water Pollution Removal Performance of Compost Filter Socks

Science.gov (United States)

In 2005, the US Environmental Protection Agency National Menu of Best Management Practices (BMPs) listed compost filter socks as an approved BMP for controlling sediment in storm runoff on construction sites. Filtrexx International manufactures and distributes Filter Soxx (FS). Literature suggests...

Evaluation of stormwater micropollutant source control and end-of-pipe control strategies using an uncertainty-calibrated integrated dynamic simulation model

DEFF Research Database (Denmark)

Vezzaro, Luca; Sharma, Anitha Kumari; Ledin, Anna

2015-01-01

(copper, zinc) and organic compounds (fluoranthene). MP fluxes were estimated by using an integrated dynamic model, in combination with stormwater quality measurements. MP sources were identified by using GIS land usage data, runoff quality was simulated by using a conceptual accumulation/washoff model......The estimation of micropollutant (MP) fluxes in stormwater systems is a fundamental prerequisite when preparing strategies to reduce stormwater MP discharges to natural waters. Dynamic integrated models can be important tools in this step, as they can be used to integrate the limited data provided...... by monitoring campaigns and to evaluate the performance of different strategies based on model simulation results. This study presents an example where six different control strategies, including both source-control and end-of-pipe treatment, were compared. The comparison focused on fluxes of heavy metals...

Radiographic Control of 137-Cs Brachytherapy Sources

International Nuclear Information System (INIS)

Bistrovic, M.; Viculin, T.; Jurkovic, S.

2003-01-01

1 37C s brachytherapy sources are practical for the intracavitary application due to their relatively long lifetime (T 1/2 = 30 y). On the other hand, due to the relatively low energy (0.66 MeV) of the emitted photons, they are suitable for an efficient radiation protection. The dose distribution around the sources is usually calculated by a specific program. However this program requires the knowledge of the position of sources within the applicator as well as the distribution of activity along them. The only way to learn these data is to make an X-ray picture of applicators and sources superimposed to the autoradiography of every source. It is difficult to achieve satisfactory radiographs with high dose rate sources with standard X-ray film material because autoradiography covers the structure of the radiographic shadow. The problem can be overcome either by applying a high intensity X-ray or gamma beam (originating from a radiotherapeutic machine), or by using photographic material of very low sensitivity, for example photographic paper. Combining both possibilities one can obtain satisfactory images. (author)

Sensitivity of the near-surface vertical electric field land Controlled-Source Electromagnetic monitoring

NARCIS (Netherlands)

Schaller, A.M.; Hunziker, J.W.; Streich, R.; Drijkoningen, G.G.

2014-01-01

We investigate potential benefits of measuring the vertical electric field component in addition to the routinely measured horizontal electric field components in onshore time-lapse controlled-source electromagnetics. Synthetic electromagnetic data based on a model of the Schoonebeek onshore oil

Bone morphogenetic proteins: from structure to clinical use

Directory of Open Access Journals (Sweden)

Granjeiro J.M.

2005-01-01

Full Text Available Bone morphogenetic proteins (BMPs are multi-functional growth factors belonging to the transforming growth factor ß superfamily. Family members are expressed during limb development, endochondral ossification, early fracture, and cartilage repair. The activity of BMPs was first identified in the 1960s but the proteins responsible for bone induction were unknown until the purification and cloning of human BMPs in the 1980s. To date, about 15 BMP family members have been identified and characterized. The signal triggered by BMPs is transduced through serine/threonine kinase receptors, type I and II subtypes. Three type I receptors have been shown to bind BMP ligands, namely: type IA and IB BMP receptors and type IA activin receptors. BMPs seem to be involved in the regulation of cell proliferation, survival, differentiation and apoptosis, but their hallmark is their ability to induce bone, cartilage, ligament, and tendon formation at both heterotopic and orthotopic sites. This suggests that, in the future, they may play a major role in the treatment of bone diseases. Several animal studies have illustrated the potential of BMPs to enhance spinal fusion, repair critical-size defects, accelerate union, and heal articular cartilage lesions. Difficulties in producing and purifying BMPs from bone tissue have prompted the attempts made by several laboratories, including ours, to express these proteins in the recombinant form in heterologous systems. This review focuses on BMP structure, molecular mechanisms of action and significance and potential applications in medical, dental and veterinary practice for the treatment of cartilage and bone-related diseases.

A Novel Coordinated Control of Renewable Energy Sources and Energy Storage System in Islanded Microgrid

DEFF Research Database (Denmark)

Gui, Yonghao; Li, Mingshen; Guerrero, Josep M.

2018-01-01

A novel coordinated control for energy storage system (ESS) and renewable energy source (RES) units is proposed in islanded AC microgrids without a phase-locked loop system. We use a proportional-resonant control technique for the ESS, which fixes the voltage and frequency of the microgrid...

Regularized inversion of controlled source and earthquake data

International Nuclear Information System (INIS)

Ramachandran, Kumar

2012-01-01

Estimation of the seismic velocity structure of the Earth's crust and upper mantle from travel-time data has advanced greatly in recent years. Forward modelling trial-and-error methods have been superseded by tomographic methods which allow more objective analysis of large two-dimensional and three-dimensional refraction and/or reflection data sets. The fundamental purpose of travel-time tomography is to determine the velocity structure of a medium by analysing the time it takes for a wave generated at a source point within the medium to arrive at a distribution of receiver points. Tomographic inversion of first-arrival travel-time data is a nonlinear problem since both the velocity of the medium and ray paths in the medium are unknown. The solution for such a problem is typically obtained by repeated application of linearized inversion. Regularization of the nonlinear problem reduces the ill posedness inherent in the tomographic inversion due to the under-determined nature of the problem and the inconsistencies in the observed data. This paper discusses the theory of regularized inversion for joint inversion of controlled source and earthquake data, and results from synthetic data testing and application to real data. The results obtained from tomographic inversion of synthetic data and real data from the northern Cascadia subduction zone show that the velocity model and hypocentral parameters can be efficiently estimated using this approach. (paper)

A Web-Based Model to Estimate the Impact of Best Management Practices

Directory of Open Access Journals (Sweden)

Youn Shik Park

2014-03-01

Full Text Available The Spreadsheet Tool for the Estimation of Pollutant Load (STEPL can be used for Total Maximum Daily Load (TMDL processes, since the model is capable of simulating the impacts of various best management practices (BMPs and low impact development (LID practices. The model computes average annual direct runoff using the Soil Conservation Service Curve Number (SCS-CN method with average rainfall per event, which is not a typical use of the SCS-CN method. Five SCS-CN-based approaches to compute average annual direct runoff were investigated to explore estimated differences in average annual direct runoff computations using daily precipitation data collected from the National Climate Data Center and generated by the CLIGEN model for twelve stations in Indiana. Compared to the average annual direct runoff computed for the typical use of the SCS-CN method, the approaches to estimate average annual direct runoff within EPA STEPL showed large differences. A web-based model (STEPL WEB was developed with a corrected approach to estimate average annual direct runoff. Moreover, the model was integrated with the Web-based Load Duration Curve Tool, which identifies the least cost BMPs for each land use and optimizes BMP selection to identify the most cost-effective BMP implementations. The integrated tools provide an easy to use approach for performing TMDL analysis and identifying cost-effective approaches for controlling nonpoint source pollution.

Reproduction of nearby sources by imposing true interaural differences on a sound field control approach

DEFF Research Database (Denmark)

Badajoz, Javier; Chang, Ji-ho; Agerkvist, Finn T.

2015-01-01

In anechoic conditions, the Interaural Level Difference (ILD) is the most significant auditory cue to judge the distance to a sound source located within 1 m of the listener's head. This is due to the unique characteristics of a point source in its near field, which result in exceptionally high...... as Pressure Matching (PM), and a binaural control technique. While PM aims at reproducing the incident sound field, the objective of the binaural control technique is to ensure a correct reproduction of interaural differences. The combination of these two approaches gives rise to the following features: (i......, distance dependent ILDs. When reproducing the sound field of sources located near the head with line or circular arrays of loudspeakers, the reproduced ILDs are generally lower than expected, due to physical limitations. This study presents an approach that combines a sound field reproduction method, known...

Six-Phase Vehicular Drive with Renewable DC Sources and Hybrid PWM Control of Four Inverters

DEFF Research Database (Denmark)

Oleschuk, Valentin; Ermuratskii, Vladimir; Blaabjerg, Frede

2015-01-01

The paper presents results of research of quad-inverter-based automotive system with combined scheme of PWM control of inverters, supplied by two renewable dc sources (by fuel cells and by battery). It has been shown, that hybrid switching techniques can be used successfully for control of vehicle...

Effect of forest harvesting best management practices on coarse woody debris distribution in stream and riparian zones in three Appalachian watersheds

Science.gov (United States)

J. M. McClure; R. K. Kolka; A. White

2004-01-01

The distribution of coarse woody debris (CWD) was analyzed in three Appalachian watersheds in eastern Kentucky, eighteen years after harvest. The three watersheds included an unharvested control (Control), a second watershed with best management practices (BMPs) applied that included a 15.2 m unharvested zone near the stream (BMP watershed), and a third watershed that...

Bone morphogenic protein: an elixir for bone grafting--a review.

Science.gov (United States)

Shah, Prasun; Keppler, Louis; Rutkowski, James

2012-12-01

Bone morphogenetic proteins (BMPs) are multifunctional growth factors that belong to the transforming growth factor beta superfamily. This literature review focuses on the molecular biology of BMPs, their mechanism of action, and subsequent applications. It also discusses uses of BMPs in the fields of dentistry and orthopedics, research on methods of delivering BMPs, and their role in tissue regeneration. BMP has positive effects on bone grafts, and their calculated and timely use with other growth factors can provide extraordinary results in fractured or nonhealing bones. Use of BMP introduces new applications in the field of implantology and bone grafting. This review touches on a few unknown facts about BMP and this ever-changing field of research to improve human life.

Quantitative evaluation of emission controls on primary and secondary organic aerosol sources during Beijing 2008 Olympics

Directory of Open Access Journals (Sweden)

S. Guo

2013-08-01

Full Text Available To assess the primary and secondary sources of fine organic aerosols after the aggressive implementation of air pollution controls during the 2008 Beijing Olympic Games, 12 h PM2.5 values were measured at an urban site at Peking University (PKU and an upwind rural site at Yufa during the CAREBEIJING-2008 (Campaigns of Air quality REsearch in BEIJING and surrounding region summer field campaign. The average PM2.5 concentrations were 72.5 ± 43.6 μg m−3 and 64.3 ± 36.2 μg m−3 (average ± standard deviation, below as the same at PKU and Yufa, respectively, showing the lowest concentrations in recent years. Combining the results from a CMB (chemical mass balance model and secondary organic aerosol (SOA tracer-yield model, five primary and four secondary fine organic aerosol sources were compared with the results from previous studies in Beijing. The relative contribution of mobile sources to PM2.5 concentrations was increased in 2008, with diesel engines contributing 16.2 ± 5.9% and 14.5 ± 4.1% and gasoline vehicles contributing 10.3 ± 8.7% and 7.9 ± 6.2% to organic carbon (OC at PKU and Yufa, respectively. Due to the implementation of emission controls, the absolute OC concentrations from primary sources were reduced during the Olympics, and the contributions from secondary formation of OC represented a larger relative source of fine organic aerosols. Compared with the non-controlled period prior to the Olympics, primary vehicle contributions were reduced by 30% at the urban site and 24% at the rural site. The reductions in coal combustion contributions were 57% at PKU and 7% at Yufa. Our results demonstrate that the emission control measures implemented in 2008 significantly alleviated the primary organic particle pollution in and around Beijing. However, additional studies are needed to provide a more comprehensive assessment of the emission control effectiveness on SOA formation.

Development of the integrated control system for the microwave ion source of the PEFP 100-MeV proton accelerator

Science.gov (United States)

Song, Young-Gi; Seol, Kyung-Tae; Jang, Ji-Ho; Kwon, Hyeok-Jung; Cho, Yong-Sub

2012-07-01

The Proton Engineering Frontier Project (PEFP) 20-MeV proton linear accelerator is currently operating at the Korea Atomic Energy Research Institute (KAERI). The ion source of the 100-MeV proton linac needs at least a 100-hour operation time. To meet the goal, we have developed a microwave ion source that uses no filament. For the ion source, a remote control system has been developed by using experimental physics and the industrial control system (EPICS) software framework. The control system consists of a versa module europa (VME) and EPICS-based embedded applications running on a VxWorks real-time operating system. The main purpose of the control system is to control and monitor the operational variables of the components remotely and to protect operators from radiation exposure and the components from critical problems during beam extraction. We successfully performed the operation test of the control system to confirm the degree of safety during the hardware performance.

EFFECTS OF LIME AMENDMENT ON THE PH OF ENGINEERED SOIL MIX FOR THE PURPOSES OF BIORETENTION

Science.gov (United States)

Bioretention basins are currently at the forefront of federal and state initiatives for urban stormwater management and water quality control. Also known as raingardens, these systems have been included in U.S. EPA’s list urban stormwater best management practices (BMPs). A bio...

Evaluating the Least Cost Selection of Agricultural Management Practices in the Five Mile Creek area of Fort Cobb Watershed, Oklahoma, USA

Science.gov (United States)

Rasoulzadeh Gharibdousti, S.; Stoecker, A.; Storm, D.

2017-12-01

One of the main causes of water quality impairment in the United States is human induced Non-Point Source (NPS) pollution through intensive agriculture. The Fort Cobb Reservoir (FCR) watershed located in west-central Oklahoma, United States is a rural agricultural catchment with known issues of NPS pollution including suspended solids, siltation, nutrients, and pesticides. Recently, several Best Management Practices (BMPs) have been implemented in the watershed (such as no-tillage and cropland to grassland conversion) to improve water quality. The objective in this study is to estimate the most cost effective selection and placement of BMPs on farmlands to mitigate soil erosion and the delivery of sediment and nutrient loads to the FCR from Five Mile Creek (FMC) area of the FCR watershed. We employed the Soil and Water Assessment Tool (SWAT) to develop the hydrological model of the study area. The watershed was delineated using the 10 m National Elevation Dataset and divided into 43 sub-basins with an average area of 8 km2. Through a combination of Soil Survey Geographic Database- SSURGO soil data, the US Department of Agriculture crop layer and the slope information, the watershed was further divided into 15,217 hydrologic response units (HRUs). The historical climate pattern in the watershed was represented by two different weather stations. The model was calibrated for the 1991 - 2000 period and validated over the 2001 - 2010 period against the monthly USGS observations of streamflow and suspended sediment concentration recorded at the watershed outlet. Model parametrization resulted in satisfactory values for the R2 (0.64, 0.35) and NS (0.61, 0.34) in calibration period and an excellent model performance (R2 = 0.79, 0.38; NS = 0.75, 0.43) in validation period for streamflow and sediment concentration respectively. We have selected 20 BMPs to estimate their efficacy in terms of water, sediment, and crop yields. Linear Programming (LP) was used to determine the

Orphan sources in Slovenia

International Nuclear Information System (INIS)

Janzekovic, H.; Cesarek, J.

2005-01-01

For decades the international standards and requirements postulate severe control over all lifecycle phases of radioactive sources in order to prevent risks associated with exposure of people and the environment. Despite this fact the orphan sources became a serious problem as a consequence of enlargement of economic transactions in many countries in Europe as well as in the world. The countries as well as international organisations, aware of this emerging problem, are trying to gain control over orphan sources using different approaches. These approaches include control over sources before they could become orphan sources. In addition, countries are also developing action plans in case that an orphan source could be found. The problems related to orphan sources in Slovenia is discussed based on the case studies from the last years. While in the nineties of the last century just a few cases of orphan sources were identified their number has increased substantially since 2003. The paper discusses the general reasons for the phenomena of orphan sources as well as the experience related to regaining control over orphan sources. (author)

Development of GUS for control applications at the Advanced Photon Source

International Nuclear Information System (INIS)

Chung, Y.; Barr, D.; Borland, M.; Kirchman, J.; Decker, G.; Kim, K.

1994-01-01

A script-based interpretive shell GUS (General Purpose Data Acquisition for Unix Shell) has been developed for application to the Advanced Photon Source (APS) control. The primary design objective of GUS is to provide a mechanism for efficient data flow among modularized objects called Data Access Modules (DAMs). GUS consists of four major components: user interface, kernel, built-in command module, and DAMS. It also incorporates the Unix shell to make use of the existing utility programs for file manipulation and data analysis. At this time, DAMs have been written for device access through EPICS (Experimental Physics and Industrial Control System), data I/O for SDDS (Self-Describing Data Set) files, matrix manipulation, graphics display, digital signal processing, and beam position feedback system control. The modular and object-oriented construction of GUS will facilitate addition of more DAMs with other functions in the future

Design and Control of Parallel Three Phase Voltage Source Inverters in Low Voltage AC Microgrid

Directory of Open Access Journals (Sweden)

El Hassane Margoum

2017-01-01

Full Text Available Design and hierarchical control of three phase parallel Voltage Source Inverters are developed in this paper. The control scheme is based on synchronous reference frame and consists of primary and secondary control levels. The primary control consists of the droop control and the virtual output impedance loops. This control level is designed to share the active and reactive power correctly between the connected VSIs in order to avoid the undesired circulating current and overload of the connected VSIs. The secondary control is designed to clear the magnitude and the frequency deviations caused by the primary control. The control structure is validated through dynamics simulations.The obtained results demonstrate the effectiveness of the control structure.

DC-bus voltage control of grid-connected voltage source converter by using space vector modulated direct power control under unbalanced network conditions

DEFF Research Database (Denmark)

Xiao, Lei; Huang, Shoudao; Lu, Kaiyuan

2013-01-01

Unbalanced grid voltage will cause large dc-bus voltage ripple and introduce high harmonic current components on the grid side. This will severely threaten the safety of the grid-connected voltage source converter (VSC) and consequently, affect the healthy operation condition of the load. In this......Unbalanced grid voltage will cause large dc-bus voltage ripple and introduce high harmonic current components on the grid side. This will severely threaten the safety of the grid-connected voltage source converter (VSC) and consequently, affect the healthy operation condition of the load....... In this study, a new proportional-integral-resonant (PI-RES) controller-based, space vector modulated direct power control topology is proposed to suppress the dc-bus voltage ripple and in the same time, controlling effectively the instantaneous power of the VSC. A special ac reactive power reference component...... is introduced in the controller, which is necessary in order to reduce the dc-bus voltage ripple and active power harmonics at the same time. The proposed control topology is implemented in the lab. Simulation and experimental results are provided to validate its performance and the analysis presented...

Role of rural solid waste management in non-point source pollution control of Dianchi Lake catchments, China

Institute of Scientific and Technical Information of China (English)

Wenjing LU; Hongtao WANG

2008-01-01

In recent years, with control of the main municipal and industrial point pollution sources and implementation of cleaning for some inner pollution sources in the water body, the discharge of point source pollution decreased gradually, while non-point source pollution has become increasingly distressing in Dianchi Lake catchments. As one of the major targets in non-point source pollution control, an integrated solid waste controlling strategy combined with a technological solution and management system was proposed and implemented based on the waste disposal situation and characteristics of rural solid waste in the demonstration area. As the key technoogy in rural solid waste treatment, both centralized plantscale composting and a dispersed farmer-operated waste treating system showed promise in rendering timely benefits in efficiency, large handling capacity, high quality of the end product, as well as good economic return. Problems encountered during multi-substrates co-com-posting such as pathogens, high moisture content, asyn-chronism in the decomposition of different substrates, and low quality of the end product can all be tackled. 92.5% of solid waste was collected in the demonstration area, while the treating and recycling ratio reached 87.9%, which pre-vented 32.2 t nitrogen and 3.9 t phosphorus per year from entering the water body of Dianchi Lake after imple-mentation of the project.

Power conversion and control methods for renewable energy sources

Science.gov (United States)

Yu, Dachuan

2005-07-01

In recent years, there has been an increase in the use of renewable energy due to the growing concern over the pollution caused by fossil-fuel-based energy. Renewable energy sources, such as photovoltaic (PV) and fuel cell, can be used to enhance the safety, reliability, sustainability, and transmission efficiency of a power system. This dissertation focuses on the power conversion and control for two major renewable-energy sources: PV and fuel cell. Firstly, a current-based, maximum power-point tracking (MPPT) algorithm is proposed for PV energy. An economical converter system using the above scheme for converting the output from PV panels into 60 Hz AC voltage is developed and built. Secondly, a novel circuit model for the Proton Exchange Membrane (PEM) fuel-cell stack that is useful in the design and analysis of fuel-cell-based power systems is proposed. This Pspice-based model uses elements available in the Pspice library with some modifications to represent both the static and dynamic responses of a PEM fuel-cell module. The accuracy of the model is verified by comparing the simulation and experimental results. Thirdly, a DSP-controlled three-phase induction-motor drive using constant voltage over frequency is built and can be used in a fuel-cell automobile. A hydrogen sensor is used in the drive to both sound an alarm and shut down the inverter trigger pulses through the DSP. Finally, a hybrid power system consisting of PV panels and fuel cell is proposed and built. In the proposed system, PV panels can supply most of the power when the sunlight is available, and the excess power required by the load is supplied by a fuel cell. Load sharing between a fuel cell (FC) and the PV panel is investigated by both simulation and experiments.

The accuracy of webcams in 2D motion analysis: sources of error and their control

International Nuclear Information System (INIS)

Page, A; Candelas, P; Belmar, F; Moreno, R

2008-01-01

In this paper, we show the potential of webcams as precision measuring instruments in a physics laboratory. Various sources of error appearing in 2D coordinate measurements using low-cost commercial webcams are discussed, quantifying their impact on accuracy and precision, and simple procedures to control these sources of error are presented. Finally, an experiment with controlled movement is performed to experimentally measure the errors described above and to assess the effectiveness of the proposed corrective measures. It will be shown that when these aspects are considered, it is possible to obtain errors lower than 0.1%. This level of accuracy demonstrates that webcams should be considered as very precise and accurate measuring instruments at a remarkably low cost

The accuracy of webcams in 2D motion analysis: sources of error and their control

Energy Technology Data Exchange (ETDEWEB)

Page, A; Candelas, P; Belmar, F [Departamento de Fisica Aplicada, Universidad Politecnica de Valencia, Valencia (Spain); Moreno, R [Instituto de Biomecanica de Valencia, Valencia (Spain)], E-mail: alvaro.page@ibv.upv.es

2008-07-15

In this paper, we show the potential of webcams as precision measuring instruments in a physics laboratory. Various sources of error appearing in 2D coordinate measurements using low-cost commercial webcams are discussed, quantifying their impact on accuracy and precision, and simple procedures to control these sources of error are presented. Finally, an experiment with controlled movement is performed to experimentally measure the errors described above and to assess the effectiveness of the proposed corrective measures. It will be shown that when these aspects are considered, it is possible to obtain errors lower than 0.1%. This level of accuracy demonstrates that webcams should be considered as very precise and accurate measuring instruments at a remarkably low cost.

Dynamic Control of Particle Deposition in Evaporating Droplets by an External Point Source of Vapor.

Science.gov (United States)

Malinowski, Robert; Volpe, Giovanni; Parkin, Ivan P; Volpe, Giorgio

2018-02-01

The deposition of particles on a surface by an evaporating sessile droplet is important for phenomena as diverse as printing, thin-film deposition, and self-assembly. The shape of the final deposit depends on the flows within the droplet during evaporation. These flows are typically determined at the onset of the process by the intrinsic physical, chemical, and geometrical properties of the droplet and its environment. Here, we demonstrate deterministic emergence and real-time control of Marangoni flows within the evaporating droplet by an external point source of vapor. By varying the source location, we can modulate these flows in space and time to pattern colloids on surfaces in a controllable manner.

Stream nitrogen sources apportionment and pollution control scheme development in an agricultural watershed in eastern China.

Science.gov (United States)

Chen, Dingjiang; Lu, Jun; Huang, Hong; Liu, Mei; Gong, Dongqin; Chen, Jiabo

2013-08-01

A modeling system that couples a land-usebased export coefficient model, a stream nutrient transport equation, and Bayesian statistics was developed for stream nitrogen source apportionment. It divides a watershed into several sub-catchments, and then considers the major landuse categories as stream nitrogen sources in each subcatchment. The runoff depth and stream water depth are considered as the major factors influencing delivery of nitrogen from land to downstream stream node within each sub-catchment. The nitrogen sources and delivery processes are lumped into several constant parameters that were calibrated using Bayesian statistics from commonly available stream monitoring and land-use datasets. This modeling system was successfully applied to total nitrogen (TN) pollution control scheme development for the ChangLe River watershed containing six sub-catchments and four land-use categories. The temporal (across months and years) and spatial (across sub-catchments and land-use categories) variability of nonpoint source (NPS) TN export to stream channels and delivery to the watershed outlet were assessed. After adjustment for in-stream TNretention, the time periods and watershed areas with disproportionately high-TN contributions to the stream were identified. Aimed at a target stream TN level of 2 mg L-1, a quantitative TN pollution control scheme was further developed to determine which sub-catchments, which land-use categories in a sub-catchment, which time periods, and how large of NPS TN export reduction were required. This modeling system provides a powerful tool for stream nitrogen source apportionment and pollution control scheme development at the watershed scale and has only limited data requirements.

Adaptive Sliding Mode Control of MEMS AC Voltage Reference Source

Directory of Open Access Journals (Sweden)

Ehsan Ranjbar

2017-01-01

Full Text Available The accuracy of physical parameters of a tunable MEMS capacitor, as the major part of MEMS AC voltage reference, is of great importance to achieve an accurate output voltage free of the malfunctioning noise and disturbance. Even though strenuous endeavors are made to fabricate MEMS tunable capacitors with desiderated accurate physical characteristics and ameliorate exactness of physical parameters’ values, parametric uncertainties ineluctably emerge in fabrication process attributable to imperfections in micromachining process. First off, this paper considers applying an adaptive sliding mode controller design in the MEMS AC voltage reference source so that it is capable of giving off a well-regulated output voltage in defiance of jumbling parametric uncertainties in the plant dynamics and also aggravating external disturbance imposed on the system. Secondly, it puts an investigatory comparison with the designed model reference adaptive controller and the pole-placement state feedback one into one’s prospective. Not only does the tuned adaptive sliding mode controller show remarkable robustness against slow parameter variation and external disturbance being compared to the pole-placement state feedback one, but also it immensely gets robust against the external disturbance in comparison with the conventional adaptive controller. The simulation results are promising.

The regulatory control of radiation sources in Turkey

International Nuclear Information System (INIS)

Uslu, I.; Birol, E.

2001-01-01

In Turkey, the national competent authority for regulating activities involving radioactive sources is the Turkish Atomic Energy Authority, which implements the responsibility for the safety and security of radiation sources through its Radiation Health and Safety Department. The report describes the organization of the regulatory infrastructure for radiation safety in Turkey and, after a brief explanation of the current legal framework for such purpose, it refers to how the management of radiation sources is carried out and to the new provisions regarding radiation sources, including inspections of licensees and training on source safety. Finally, the report provides information on the Ikitelli radiological accident in Turkey and the current public concern about radiation sources after it happened. (author)

Analysis of Best Management Practices Implementation on Water Quality Using the Soil and Water Assessment Tool

OpenAIRE

Jason Motsinger; Prasanta Kalita; Rabin Bhattarai

2016-01-01

The formation of hypoxic zone in the Gulf of Mexico can be traced to agricultural watersheds in the Midwestern United States that are artificially drained in order to make the land suitable for agriculture. A number of best management practices (BMPs) have been introduced to improve the water quality in the region but their relative effectivenss of these BMPs in reducing nutrient load has not been properly quantified. In order to determine the BMPs useful for reducing nutrient discharge from ...

Controlling single and few-layer graphene crystals growth in a solid carbon source based chemical vapor deposition

International Nuclear Information System (INIS)

Papon, Remi; Sharma, Subash; Shinde, Sachin M.; Vishwakarma, Riteshkumar; Tanemura, Masaki; Kalita, Golap

2014-01-01

Here, we reveal the growth process of single and few-layer graphene crystals in the solid carbon source based chemical vapor deposition (CVD) technique. Nucleation and growth of graphene crystals on a polycrystalline Cu foil are significantly affected by the injection of carbon atoms with pyrolysis rate of the carbon source. We observe micron length ribbons like growth front as well as saturated growth edges of graphene crystals depending on growth conditions. Controlling the pyrolysis rate of carbon source, monolayer and few-layer crystals and corresponding continuous films are obtained. In a controlled process, we observed growth of large monolayer graphene crystals, which interconnect and merge together to form a continuous film. On the other hand, adlayer growth is observed with an increased pyrolysis rate, resulting few-layer graphene crystal structure and merged continuous film. The understanding of monolayer and few-layer crystals growth in the developed CVD process can be significant to grow graphene with controlled layer numbers.

Controlling hazardous energy sources (lockout/tagout)

Science.gov (United States)

Dominguez, Manuel B.

1991-10-01

The minimum requirements as established by the Occupational Safety and Health Administration (OSHA) standard 29 CFR 1910.147 are discussed for preventing the unexpected operation of equipment or release of energy which could cause injury to personnel, damage to equipment, harm to the environment, or loss or compromise of test data. Safety requirements both for government and contractor personnel are explained for potentially hazardous energy sources during work operations at LeRC (Cleveland and Plum Brook Stations). Basic rules are presented to ensure protection against harmful exposures, and baseline implementation requirements are discussed from which detailed lockout/tagout procedures can be developed for individual equipment items. Examples of energy sources covered by this document include electrical, pneumatic, mechanical, chemical, cryogenic, thermal, spring tension/compression suspended or moving loads, and other potentially hazardous sources. Activities covered by this standard include, but are not limited to, construction, maintenance, installation, calibration, inspection, cleaning, or repair.

Control system for 5 MW neutral beam ion source for SST1

Science.gov (United States)

Patel, G. B.; Onali, Raja; Sharma, Vivek; Suresh, S.; Tripathi, V.; Bandyopadhyay, M.; Singh, N. P.; Thakkar, Dipal; Gupta, L. N.; Singh, M. J.; Patel, P. J.; Chakraborty, A. K.; Baruah, U. K.; Mattoo, S. K.

2006-01-01

This article describes the control system for a 5MW ion source of the NBI (neutral beam injector) for steady-state superconducting tokamak-1 (SST-1). The system uses both hardware and software solutions. It comprises a DAS (data acquisition system) and a control system. The DAS is used to read the voltage and current signals from eight filament heater power supplies and 24 discharge power supplies. The control system is used to adjust the filament heater current in order to achieve an effective control on the discharge current in the plasma box. The system consists of a VME (Verse Module Eurocard) system and C application program running on a VxWorks™ real-time operating system. A PID (proportional, integral, and differential) algorithm is used to control the filament heater current. Experiments using this system have shown that the discharge current can be controlled within 1% accuracy for a PID loop time of 20ms. Response of the control system to the pressure variation of the gas in the chamber has also been studied and compared with the results obtained from those of an uncontrolled system. The present approach increases the flexibility of the control system. It not only eases the control of the plasma but also allows an easy changeover to various operation scenarios.

Low-level rf control of Spallation Neutron Source: System and characterization

Directory of Open Access Journals (Sweden)

Hengjie Ma

2006-03-01

Full Text Available The low-level rf control system currently commissioned throughout the Spallation Neutron Source (SNS LINAC evolved from three design iterations over 1 yr intensive research and development. Its digital hardware implementation is efficient, and has succeeded in achieving a minimum latency of less than 150 ns which is the key for accomplishing an all-digital feedback control for the full bandwidth. The control bandwidth is analyzed in frequency domain and characterized by testing its transient response. The hardware implementation also includes the provision of a time-shared input channel for a superior phase differential measurement between the cavity field and the reference. A companion cosimulation system for the digital hardware was developed to ensure a reliable long-term supportability. A large effort has also been made in the operation software development for the practical issues such as the process automations, cavity filling, beam loading compensation, and the cavity mechanical resonance suppression.

A digital controlled negative high voltage power source for LINAC of HLS

International Nuclear Information System (INIS)

Gao Hui; Chen Jun; Hong Jun; Wang Weibing

2005-01-01

This paper introduces the working principle of a 10-80 kV negative high voltage power source for the electronic gun of the 200 MeV LINAC of NSRL, especially how to realize the switch power, voltage/current sampling, feedback control and microcontroller module. The firmware design for the SOC microcontroller of ADuC8xx and the application software design for PC are also presented. (authors)

Control and reception of out of use radioactive sources at the CDTN/CNEN, Minas Gerais, Brazil; Controle e recebimento de fontes radioativas fora de uso no CDTN/CNEN

Energy Technology Data Exchange (ETDEWEB)

Reis, Luiz C.A.; Guzella, Marcia F.R.; Seles, Sandro R.N.; Cuccia, Valeria, E-mail: reislca@cdtn.b, E-mail: mfrg@cdtn.b, E-mail: seless@cdtn.b, E-mail: vc@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2011-10-26

For reception of the received sources and for accomplish with CNEN regulations and IAEA recommendations, the CDTN have implanted a system for receiving those sources and all the procedures for effective control and recovering of information. The CDTN posses a source deposit, a data bank for the inventory and also a Laboratory for Treatment of Sealed Sources

Impact of head models in N170 component source imaging: results in control subjects and ADHD patients

International Nuclear Information System (INIS)

Beltrachini, L; Blenkmann, A; Ellenrieder, N von; Muravchik, C H; Petroni, A; Urquina, H; Manes, F; Ibáñez, A

2011-01-01

The major goal of evoked related potential studies arise in source localization techniques to identify the loci of neural activity that give rise to a particular voltage distribution measured on the surface of the scalp. In this paper we evaluate the effect of the head model adopted in order to estimate the N170 component source in attention deficit hyperactivity disorder (ADHD) patients and control subjects, considering faces and words stimuli. The standardized low resolution brain electromagnetic tomography algorithm (sLORETA) is used to compare between the three shell spherical head model and a fully realistic model based on the ICBM-152 atlas. We compare their variance on source estimation and analyze the impact on the N170 source localization. Results show that the often used three shell spherical model may lead to erroneous solutions, specially on ADHD patients, so its use is not recommended. Our results also suggest that N170 sources are mainly located in the right occipital fusiform gyrus for faces stimuli and in the left occipital fusiform gyrus for words stimuli, for both control subjects and ADHD patients. We also found a notable decrease on the N170 estimated source amplitude on ADHD patients, resulting in a plausible marker of the disease.

Impact of head models in N170 component source imaging: results in control subjects and ADHD patients

Science.gov (United States)

Beltrachini, L.; Blenkmann, A.; von Ellenrieder, N.; Petroni, A.; Urquina, H.; Manes, F.; Ibáñez, A.; Muravchik, C. H.

2011-12-01

The major goal of evoked related potential studies arise in source localization techniques to identify the loci of neural activity that give rise to a particular voltage distribution measured on the surface of the scalp. In this paper we evaluate the effect of the head model adopted in order to estimate the N170 component source in attention deficit hyperactivity disorder (ADHD) patients and control subjects, considering faces and words stimuli. The standardized low resolution brain electromagnetic tomography algorithm (sLORETA) is used to compare between the three shell spherical head model and a fully realistic model based on the ICBM-152 atlas. We compare their variance on source estimation and analyze the impact on the N170 source localization. Results show that the often used three shell spherical model may lead to erroneous solutions, specially on ADHD patients, so its use is not recommended. Our results also suggest that N170 sources are mainly located in the right occipital fusiform gyrus for faces stimuli and in the left occipital fusiform gyrus for words stimuli, for both control subjects and ADHD patients. We also found a notable decrease on the N170 estimated source amplitude on ADHD patients, resulting in a plausible marker of the disease.

Impact of head models in N170 component source imaging: results in control subjects and ADHD patients

Energy Technology Data Exchange (ETDEWEB)

Beltrachini, L; Blenkmann, A; Ellenrieder, N von; Muravchik, C H [Laboratory of Industrial Electronics, Control and Instrumentation (LEICI), National University of La Plata (Argentina); Petroni, A [Integrative Neuroscience Laboratory, Physics Department, University of Buenos Aires, Buenos Aires (Argentina); Urquina, H; Manes, F; Ibanez, A [Institute of Cognitive Neurology (INECO) and Institute of Neuroscience, Favaloro University, Buenos Aires (Argentina)

2011-12-23

The major goal of evoked related potential studies arise in source localization techniques to identify the loci of neural activity that give rise to a particular voltage distribution measured on the surface of the scalp. In this paper we evaluate the effect of the head model adopted in order to estimate the N170 component source in attention deficit hyperactivity disorder (ADHD) patients and control subjects, considering faces and words stimuli. The standardized low resolution brain electromagnetic tomography algorithm (sLORETA) is used to compare between the three shell spherical head model and a fully realistic model based on the ICBM-152 atlas. We compare their variance on source estimation and analyze the impact on the N170 source localization. Results show that the often used three shell spherical model may lead to erroneous solutions, specially on ADHD patients, so its use is not recommended. Our results also suggest that N170 sources are mainly located in the right occipital fusiform gyrus for faces stimuli and in the left occipital fusiform gyrus for words stimuli, for both control subjects and ADHD patients. We also found a notable decrease on the N170 estimated source amplitude on ADHD patients, resulting in a plausible marker of the disease.

An Open Source Rapid Computer Aided Control System Design Toolchain Using Scilab, Scicos and RTAI Linux

Science.gov (United States)

Bouchpan-Lerust-Juéry, L.

2007-08-01

Current and next generation on-board computer systems tend to implement real-time embedded control applications (e.g. Attitude and Orbit Control Subsystem (AOCS), Packet Utililization Standard (PUS), spacecraft autonomy . . . ) which must meet high standards of Reliability and Predictability as well as Safety. All these requirements require a considerable amount of effort and cost for Space Sofware Industry. This paper, in a first part, presents a free Open Source integrated solution to develop RTAI applications from analysis, design, simulation and direct implementation using code generation based on Open Source and in its second part summarises this suggested approach, its results and the conclusion for further work.

Investigating The Integral Control Rod Worth Of The Miniature Neutron Source Reactor MNSR

International Nuclear Information System (INIS)

Nguyen Hoang Hai; Do Quang Binh

2011-01-01

Determining control rod characteristics is an essential problem of nuclear reactor analysis. In this research, the integral control rod worth of the miniature neutron source reactor MNSR is investigated. Some other parameters of the nuclear reactor, such as core excess reactivity, shut down margin, are also calculated. Group constants for all reactor components are generated by the WIMSD code and then are used in the CITATION code to solve the neutron diffusion equations. The maximum relative error of the calculated results compared with the measurement data is about 3.5%. (author)

Tungsten transport and sources control in JET ITER-like wall H-mode plasmas

Energy Technology Data Exchange (ETDEWEB)

Fedorczak, N., E-mail: nicolas.fedorczak@cea.fr [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Monier-Garbet, P. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Pütterich, T. [MPI für Plasmaphysik, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Brezinsek, S. [Institute of Energy and Climate Research, Forschungszentrum Jlich, Assoc EURATOM-FZJ, Jlich (Germany); Devynck, P.; Dumont, R.; Goniche, M.; Joffrin, E. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Lerche, E. [Association EURATOM-Belgian State, LPP-ERM-KMS, TEC partner, Brussels (Belgium); Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Lipschultz, B. [York Plasma Institute, University of York, Heslington, York YO10 5DD (United Kingdom); Luna, E. de la [Laboratorio Nacional de Fusin, Asociacin EURATOM/CIEMAT, 28040 Madrid (Spain); Maddison, G. [Culham Centre for Fusion Energy, EURATOM-CCFE Association, Abingdon (United Kingdom); Maggi, C. [MPI für Plasmaphysik, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Matthews, G. [Culham Centre for Fusion Energy, EURATOM-CCFE Association, Abingdon (United Kingdom); Nunes, I. [Istituto de plasmas e fusao nuclear, Lisboa (Portugal); Rimini, F. [Culham Centre for Fusion Energy, EURATOM-CCFE Association, Abingdon (United Kingdom); Solano, E.R. [Laboratorio Nacional de Fusin, Asociacin EURATOM/CIEMAT, 28040 Madrid (Spain); Tamain, P. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Tsalas, M. [Association EURATOM-Hellenic Republic, NCSR Demokritos 153 10, Attica (Greece); Vries, P. de [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France)

2015-08-15

A set of discharges performed with the JET ITER-like wall is investigated with respect to control capabilities on tungsten sources and transport. In attached divertor regimes, increasing fueling by gas puff results in higher divertor recycling ion flux, lower divertor tungsten source, higher ELM frequency and lower core plasma radiation, dominated by tungsten ions. Both pedestal flushing by ELMs and divertor screening (including redeposition) are possibly responsible. For specific scenarios, kicks in plasma vertical position can be employed to increase the ELM frequency, which results in slightly lower core radiation. The application of ion cyclotron radio frequency heating at the very center of the plasma is efficient to increase the core electron temperature gradient and flatten electron density profile, resulting in a significantly lower central tungsten peaking. Beryllium evaporation in the main chamber did not reduce the local divertor tungsten source whereas core radiation was reduced by approximately 50%.

Bone morphogenetic protein-7 promotes chondrogenesis in human amniotic epithelial cells.

Science.gov (United States)

Zhou, Junjie; Yu, Guangrong; Cao, Chengfu; Pang, Jinhui; Chen, Xianqi

2011-06-01

Bone morphogenetic proteins (BMPs) play important roles at multiple stages of chondrogenesis. This study was undertaken to investigate the potential role of bone morphogenetic protein-7 (BMP-7) in the differentiation of chondrocytes using tissue engineering techniques. The impact of BMP-7 on human amniotic epithelial cells (hAECs) was tested. The hAECs were treated either with recombinant human BMP-7 cDNA or with transforming growth factor beta 1 (TGF-β1) as a positive control for three weeks in vitro. Cartilaginous differentiation and proliferation were assayed by quantitative RT-PCR, histology, and in situ hybridization. Our results were such that hAECs treated with either BMP-7 or TGF-β1 expressed cartilage markers (aggrecan, Sox9, CEP-68, and type II and X collagens) within three weeks. Compared with a control vector, BMP-7 induced a decrease in type I collagen expression, while the transcription of the cartilage-specific type II collagen remained stable. In induction experiments, BMP-7 transgenic hAECs exhibited the largest amount of matrix synthesis. In conclusion, these data indicate that BMP-7 plays an important role in inducing the production of cartilage by hAECs in vitro. Cartilage differentiation and matrix maturation can be promoted by BMPs in a cartilage engineering paradigm. These properties make BMPs promising tools in the engineering of cartilaginous joint bio-prostheses and as candidate biological agents or genes for cartilage stabilisation.

Low order modelling and closed-loop thermal control of a ventilated plate subject to a heat source disturbance

International Nuclear Information System (INIS)

Videcoq, E; Girault, M; Petit, D

2012-01-01

A multi-input multi-output (MIMO) thermal control problem in real-time is investigated. An aluminum slab is heated on one side by a radiative heat source and cooled on the other side by a fan panel. Starting from a nominal steady state configuration of heat source power and ventilation level, the objective is to control temperature at 4 chosen locations on the rear side when the thermal system is subject to a perturbation: the heat source power. The 4 actuators are the ventilation levels of 4 fans. The hypothesis of small inputs and temperature responses deviations is made, resulting in the assumption of a linear control problem. The originality of this work is twofold: (i) instead of a (large-sized) classical heat transfer model built from spatial discretization of local partial differential equations governing physics over the system domain, a low order model is identified from experimental data using the Modal Identification Method, (ii) this low order model is used to perform state feedback control in real time through a Linear Quadratic Gaussian (LQG) compensator.

Passivity-Based Control by Series/Parallel Damping of Single-Phase PWM Voltage Source Converter

NARCIS (Netherlands)

del Puerto Flores, Dunstano; Scherpen, Jacqueline; Liserre, Marco; de Vries, Martijn M. J.; Kransse, Marco J.; Monopoli, Vito Giuseppe

This paper describes a detailed design procedure for passivity-based controllers developed using the Brayton-Moser (BM) framework. Several passivity-based feedback designs are presented for the voltage-source converter, specifically for the H-bridge converter, since nowadays it is one of the

Adapting Controlled-source Coherence Analysis to Dense Array Data in Earthquake Seismology

Science.gov (United States)

Schwarz, B.; Sigloch, K.; Nissen-Meyer, T.

2017-12-01

Exploration seismology deals with highly coherent wave fields generated by repeatable controlled sources and recorded by dense receiver arrays, whose geometry is tailored to back-scattered energy normally neglected in earthquake seismology. Owing to these favorable conditions, stacking and coherence analysis are routinely employed to suppress incoherent noise and regularize the data, thereby strongly contributing to the success of subsequent processing steps, including migration for the imaging of back-scattering interfaces or waveform tomography for the inversion of velocity structure. Attempts have been made to utilize wave field coherence on the length scales of passive-source seismology, e.g. for the imaging of transition-zone discontinuities or the core-mantle-boundary using reflected precursors. Results are however often deteriorated due to the sparse station coverage and interference of faint back-scattered with transmitted phases. USArray sampled wave fields generated by earthquake sources at an unprecedented density and similar array deployments are ongoing or planned in Alaska, the Alps and Canada. This makes the local coherence of earthquake data an increasingly valuable resource to exploit.Building on the experience in controlled-source surveys, we aim to extend the well-established concept of beam-forming to the richer toolbox that is nowadays used in seismic exploration. We suggest adapted strategies for local data coherence analysis, where summation is performed with operators that extract the local slope and curvature of wave fronts emerging at the receiver array. Besides estimating wave front properties, we demonstrate that the inherent data summation can also be used to generate virtual station responses at intermediate locations where no actual deployment was performed. Owing to the fact that stacking acts as a directional filter, interfering coherent wave fields can be efficiently separated from each other by means of coherent subtraction. We

Nonlinear control of voltage source converters in AC-DC power system.

Science.gov (United States)

Dash, P K; Nayak, N

2014-07-01

This paper presents the design of a robust nonlinear controller for a parallel AC-DC power system using a Lyapunov function-based sliding mode control (LYPSMC) strategy. The inputs for the proposed control scheme are the DC voltage and reactive power errors at the converter station and the active and reactive power errors at the inverter station of the voltage-source converter-based high voltage direct current transmission (VSC-HVDC) link. The stability and robust tracking of the system parameters are ensured by applying the Lyapunov direct method. Also the gains of the sliding mode control (SMC) are made adaptive using the stability conditions of the Lyapunov function. The proposed control strategy offers invariant stability to a class of systems having modeling uncertainties due to parameter changes and exogenous inputs. Comprehensive computer simulations are carried out to verify the proposed control scheme under several system disturbances like changes in short-circuit ratio, converter parametric changes, and faults on the converter and inverter buses for single generating system connected to the power grid in a single machine infinite-bus AC-DC network and also for a 3-machine two-area power system. Furthermore, a second order super twisting sliding mode control scheme has been presented in this paper that provides a higher degree of nonlinearity than the LYPSMC and damps faster the converter and inverter voltage and power oscillations. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Civilizing the 'Barbarian': a critical analysis of behaviour modification programmes in forensic psychiatry settings.

Science.gov (United States)

Holmes, Dave; Murray, Stuart J

2011-04-01

Drawing on the works of Erving Goffman and Michel Foucault, this article presents part of the results of a qualitative study conducted in a forensic psychiatry setting. For many years, behaviour modification programmes (BMPs) have been subjected to scrutiny and harsh criticism on the part of researchers, clinicians and professional organizations. Nevertheless, BMPs continue to be in vogue in some 'total' institutions, such as psychiatric hospitals and prisons. Discourse analysis of mute evidence available in situ was used to critically look at behaviour modification programmes. Compelling examples of behaviour modification care plans are used to illustrate our critical analysis and to support our claim that BMPs violate both scientific and ethical norms in the name of doing 'what is best' for the patients. We argue that the continued use of BMPs is not only flawed from a scientific perspective, but constitutes an unethical approach to the management of nursing care for mentally ill offenders. Nurse managers need to be aware that BMPs violate ethical standards in nursing. As a consequence, they should overtly question the use of these approaches in psychiatric nursing. © 2011 The Authors. Journal compilation © 2011 Blackwell Publishing Ltd.

Standards and the design of the Advanced Photon Source control system

International Nuclear Information System (INIS)

McDowell, W.P.; Knott, M.J.; Lenkszus, F.R.; Kraimer, M.R.; Daly, R.T.; Arnold, N.D.; Anderson, M.D.; Anderson, J.B.; Zieman, R.C.; Cha, Ben-Chin K.; Vong, F.C.; Nawrocki, G.J.; Gunderson, G.R.; Karonis, N.T.; Winans, J.R.

1991-01-01

The Advanced Photon Source (APS), now under construction at Argonne National Laboratory is a 7 GeV positron storage ring dedicated to research facilities using synchrotron radiation. This ring, along with its injection accelerators is to be controlled and monitored with a single, flexible, and expandable control system. In the conceptual stage the control system design group faced the challenges that face all control system designers: to force the machine designers to quantify and codify the system requirements, to protect the investment in hardware and software from rapid obsolescence, and to find methods of quickly incorporating new generations of equipment and replace of obsolete equipment without disrupting the exiting system. To solve these and related problems, the APS control system group made an early resolution to use standards in the design of the system. This paper will cover the present status of the APS control system as well as discuss the design decisions which led us to use industrial standards and collaborations with other laboratories whenever possible to develop a control system. It will explain the APS control system and illustrate how the use of standards has allowed APS to design a control system whose implementation addresses these issues. The system will use high performance graphic workstations using an X-Windows Graphical User Interface at the operator interface level. It connects to VME-based microprocessors at the field level using TCP/IP protocols over high performance networks. This strategy assures the flexibility and expansibility of the control system. A defined interface between the system components will allow the system to evolve with the direct addition of future, improved equipment and new capabilities

RIO EPICS device support application case study on an ion source control system (ISHP)

Energy Technology Data Exchange (ETDEWEB)

Sanz, Diego [UPM – Universidad Politécnica de Madrid, Madrid (Spain); Ruiz, Mariano, E-mail: mariano.ruiz@upm.es [UPM – Universidad Politécnica de Madrid, Madrid (Spain); Eguiraun, Mikel [Department of Electricity and Electronic, Faculty of Science and Technology, University of Basque Country, Bilbao (Spain); Arredondo, Iñigo [ESS Bilbao Consortium, Zamudio (Spain); Badillo, Inari; Jugo, Josu [Department of Electricity and Electronic, Faculty of Science and Technology, University of Basque Country, Bilbao (Spain); Vega, Jesús; Castro, Rodrigo [Asociación EURATOM/CIEMAT, Madrid (Spain)

2015-10-15

Highlights: • A use case example of RIO/FlexRIO design methodology is described. • Ion source device is controlled and monitored by means EPICS IOCs. • NIRIO EPICS device support demonstrates that is able to manage RIO devices. • Easy and fast deployment is possible using RIO/FlexRIO design methodology using NIRIO-EDS. • RIO/FlexRIO technology and EPICS are a good combination for support large scale experiments in fusion environments. - Abstract: Experimental Physics and Industrial Control System (EPICS) is a software tool that during last years has become relevant as a main framework to deploy distributed control systems in large scientific environments. At the moment, ESS Bilbao uses this middleware to perform the control of their Ion Source Hydrogen Positive (ISHP) project. The implementation of the control system was based on: PXI Real Time controllers using the LabVIEW-RT and LabVIEW-EPICS tools; and RIO devices based on Field-Programmable Gate Array (FPGA) technology. Intended to provide a full compliant EPICS IOCs for RIO devices and to avoid additional efforts on the system maintainability, a migration of the current system to a derivative Red Hat Linux (CentOS) environment has been conducted. This paper presents a real application case study for using the NIRIO EPICS device support (NIRIO-EDS) to give support to the ISHP. Although RIO FPGA configurations are particular solutions for ISHP performance, the NIRIO-EDS has permitted the control and monitoring of devices by applying a well-defined design methodology into the previous FPGA configuration for RIO/FlexRIO devices. This methodology has permitted a fast and easy deployment for the new robust, scalable and maintainable software to support RIO devices into the ISHP control architecture.

Stormwater pollution treatment BMP discharge structures.

Science.gov (United States)

2014-03-01

Structural best management practices (BMPs) are used to capture and treat stormwater runoff. Most structural BMPs provide treatment by filtering : runoff through a filter media or collecting it in a detention basin and slowly discharging it over an e...

Formaldehyde and acetaldehyde exposure mitigation in US residences: In-home measurements of ventilation control and source control

Energy Technology Data Exchange (ETDEWEB)

Hult, Erin L. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Willem, Henry [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Price, Phillip N. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Hotchi, Toshifumi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Russell, Marion L. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Singer, Brett C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2014-10-01

Measurements were taken in new US residences to assess the extent to which ventilation and source control can mitigate formaldehyde exposure. Increasing ventilation consistently lowered indoor formaldehyde concentrations. However, at a reference air exchange rate of 0.35 h^-1, increasing ventilation was up to 60% less effective than would be predicted if the emission rate were constant. This is consistent with formaldehyde emission rates decreasing as air concentrations increase, as observed in chamber studies. In contrast, measurements suggest acetaldehyde emission was independent of ventilation rate. To evaluate the effectiveness of source control, formaldehyde concentrations were measured in Leadership in Energy and Environmental Design (LEED) certified/Indoor airPLUS homes constructed with materials certified to have low emission rates of volatile organic compounds (VOC). At a reference air exchange rate of 0.35 h^-1, and adjusting for home age, temperature and relative humidity, formaldehyde concentrations in homes built with low-VOC materials were 42% lower on average than in reference new homes with conventional building materials. Without adjustment, concentrations were 27% lower in the low-VOC homes. The mean and standard deviation of formaldehyde concentration were 33 μg m-3 and 22 μg m^-3 for low-VOC homes and 45 μg m^-3 and 30 μg m^-3 for conventional.

A scanning point source for quality control of FOV uniformity in GC-PET imaging

International Nuclear Information System (INIS)

Bergmann, H.; Minear, G.; Dobrozemsky, G.; Nowotny, R.; Koenig, B.

2002-01-01

Aim: PET imaging with coincidence cameras (GC-PET) requires additional quality control procedures to check the function of coincidence circuitry and detector zoning. In particular, the uniformity response over the field of view needs special attention since it is known that coincidence counting mode may suffer from non-uniformity effects not present in single photon mode. Materials and methods: An inexpensive linear scanner with a stepper motor and a digital interface to a PC with software allowing versatile scanning modes was developed. The scanner is used with a source holder containing a Sodium-22 point source. While moving the source along the axis of rotation of the GC-PET system, a tomographic acquisition takes place. The scan covers the full axial field of view of the 2-D or 3-D scatter frame. Depending on the acquisition software, point source scanning takes place continuously while only one projection is acquired or is done in step-and-shoot mode with the number of positions equal to the number of gantry steps. Special software was developed to analyse the resulting list mode acquisition files and to produce an image of the recorded coincidence events of each head. Results: Uniformity images of coincidence events were obtained after further correction for systematic sensitivity variations caused by acquisition geometry. The resulting images are analysed visually and by calculating NEMA uniformity indices as for a planar flood field. The method has been applied successfully to two different brands of GC-PET capable gamma cameras. Conclusion: Uniformity of GC-PET can be tested quickly and accurately with a routine QC procedure, using a Sodium-22 scanning point source and an inexpensive mechanical scanning device. The method can be used for both 2-D and 3-D acquisition modes and fills an important gap in the quality control system for GC-PET

Non-point Source Pollution Modeling Using Geographic Information System (GIS for Representing Best Management Practices (BMP in the Gorganrood Watershed

Directory of Open Access Journals (Sweden)

Z. Pasandidehfard

2014-09-01

Full Text Available The most important pollutants that cause water pollution are nitrogen and phosphorus from agricultural runoff called Non-Point Source Pollution (NPS. To solve this problem, management practices known as BMPs or Best Management Practices are applied. One of the common methods for Non-Point Source Pollution prediction is modeling. By modeling, efficiency of many practices can be tested before application. In this study, land use changes were studied from the years 1984 till 2010 that showed an increase in agricultural lands from 516908.52 to 630737.19 ha and expansion of cities from 5237.87 to 15487.59 ha and roads from 9666.07 to 11430.24 ha. Using L-THIA model (from nonpoint source pollution models for both land use categories, the amount of pollutant and the volume of runoff were calculated that showed high growth. Then, the seventh sub-basin was recognized as a critical zone in terms of pollution among the sub-basins. In the end, land use change was considered as a BMP using Multi-Criteria Evaluation (MCE based on which a more suitable land use map was produced. After producing the new land use map, L-THIA model was run again and the result of the model was compared to the actual land use to show the effect of this BMP. Runoff volume decreased from 367.5 to 308.6 M3/ha and nitrogen in runoff was reduced from 3.26 to 1.58 mg/L and water BOD from 3.61 to 2.13 mg/L. Other pollutants also showed high reduction. In the end, land use change is confirmed as an effective BMP for Non-Point Source Pollution reduction.

A green paper on the regulation and control of sources of ionizing radiation

International Nuclear Information System (INIS)

1990-01-01

This publication reviews the evidences that sources of ionizing radiation are potentially hazardous to the public and the environment unless appropriate measures are taken to regulate and control their possession, use and the ultimate disposal. The current regulations, subject to some amendments are described and the impacts likely to result from the amendments are discussed. 9 tabs

crm-1 facilitates BMP signaling to control body size in Caenorhabditis elegans.

Science.gov (United States)

Fung, Wong Yan; Fat, Ko Frankie Chi; Eng, Cheah Kathryn Song; Lau, Chow King

2007-11-01

We have identified in Caenorhabditis elegans a homologue of the vertebrate Crim1, crm-1, which encodes a putative transmembrane protein with multiple cysteine-rich (CR) domains known to have bone morphogenetic proteins (BMPs) binding activity. Using the body morphology of C. elegans as an indicator, we showed that attenuation of crm-1 activity leads to a small body phenotype reminiscent of that of BMP pathway mutants. We showed that the crm-1 loss-of-function phenotype can be rescued by constitutive supply of sma-4 activity. crm-1 can enhance BMP signaling and this activity is dependent on the presence of the DBL-1 ligand and its receptors. crm-1 is expressed in neurons at the ventral nerve cord, where the DBL-1 ligand is produced. However, ectopic expression experiments reveal that crm-1 gene products act outside the DBL-1 producing cells and function non-autonomously to facilitate dbl/sma pathway signaling to control body size.

The deep-tow marine controlled-source electromagnetic transmitter system for gas hydrate exploration

Science.gov (United States)

Wang, Meng; Deng, Ming; Wu, Zhongliang; Luo, Xianhu; Jing, Jianen; Chen, Kai

2017-02-01

The Marine Controlled-Source Electromagnetic (MCSEM) method has been recognized as an important and effective tool to detect electrically resistive structures, such as oil, gas, and gas hydrate. The MCSEM performance is strongly influenced by the transmitter system design. We have developed a deep-tow MCSEM transmitter system. In this paper, some new technical details will be present. A 10,000 m optical-electrical composite cable is used to support high power transmission and fast data transfer; a new clock unit is designed to keep the synchronization between transmitter and receivers, and mark the time stamp into the transmission current full waveform; a data link is established to monitor the real-time altitude of the tail unit; an online insulation measuring instrument is adopted to monitor current leakage from high voltage transformer; a neutrally buoyant dipole antenna of copper cable and flexible electrodes are created to transmit the large power current into seawater; a new design method for the transmitter, which is called "real-time control technology of hardware parallelism", is described to achieve inverting and recording high-power current waveform, controlling functions, and collecting auxiliary information. We use a gas hydrate exploration test to verify the performance of the transmitter system, focusing on more technical details, rather than applications. The test shows that the transmitter can be used for gas hydrate exploration as an effective source.

Recommended industry best management practices for the prevention of Phytophthora ramorum introduction in nursery operations

Science.gov (United States)

Karen Suslow

2008-01-01

The following industry recommended best management practices (BMPs), designed for growers and/or interstate shippers of host and associated host plants of Phytophthora ramorum, consists of biosecurity guidelines created by and for nursery growers in order to reduce the risks associated with P. ramorum. The control of P....

Simulation of neutron multiplicity measurements using Geant4. Open source software for nuclear arms control

Energy Technology Data Exchange (ETDEWEB)

Kuett, Moritz

2016-07-07

Nuclear arms control, including nuclear safeguards and verification technologies for nuclear disarmament typically use software as part of many different technological applications. This thesis proposes to use three open source criteria for such software, allowing users and developers to have free access to a program, have access to the full source code and be able to publish modifications for the program. This proposition is presented and analyzed in detail, together with the description of the development of ''Open Neutron Multiplicity Simulation'', an open source software tool to simulate neutron multiplicity measurements. The description includes physical background of the method, details of the developed program and a comprehensive set of validation calculations.

Single Phase Current-Source Active Rectifier for Traction: Control System Design and Practical Problems

Directory of Open Access Journals (Sweden)

Jan Michalik

2006-01-01

Full Text Available This research has been motivated by industrial demand for single phase current-source active rectifier dedicated for reconstruction of older types of dc machine locomotives. This paper presents converters control structure design and simulations. The proposed converter control is based on the mathematical model and due to possible interaction with railway signaling and required low switching frequency employs synchronous PWM. The simulation results are verified by experimental tests performed on designed laboratory prototype of power of 7kVA

Means for controlling operation of power sources associated with an axial tomographic system

International Nuclear Information System (INIS)

1976-01-01

An axial tomographic system is described having scanner means normally in an off-condition where all associated power sources are electrically isolated from the units driven thereby. It also includes means for activating the scanner means to establish an on-condition, control means including means to measure one or more system parameters when the scanner means is in an on-condition and to determine if the measured parameters are within predetermined limits, and means for maintaining the on-condition only if the control means is properly operational and all measured system parameters are within the predetermined limits

Mount St. Helens: Controlled-source audio-frequency magnetotelluric (CSAMT) data and inversions

Science.gov (United States)

Wynn, Jeff; Pierce, Herbert A.

2015-01-01

This report describes a series of geoelectrical soundings carried out on and near Mount St. Helens volcano, Washington, in 2010–2011. These soundings used a controlled-source audio-frequency magnetotelluric (CSAMT) approach (Zonge and Hughes, 1991; Simpson and Bahr, 2005). We chose CSAMT for logistical reasons: It can be deployed by helicopter, has an effective depth of penetration of as much as 1 kilometer, and requires less wire than a Schlumberger sounding.

Pool of bovine morphogenetic proteins and guided tissue regeneration in the treatment of intrabony periodontal defects: I- Clinical measurements ''Pool'' de proteínas morfogenéticas bovinas no tratamento de defeitos periodontais intra-ósseos: I- Medidas clínicas

Directory of Open Access Journals (Sweden)

Maria do Carmo Machado Guimarães

2004-03-01

Full Text Available The purpose of this study was to evaluate the effect of the pool of bovine BMPs on the treatment of intrabony defects. The sample comprised 15 patients aged 26 to 57 years old presenting with 10 pairs of lesions of 2 or 3 walls or 2-3 walls ³5mm, located in the same type teeth (premolar or molar and same jaw. The test defects were treated with combination of a pool of bovine bone morphogenetic and resorbable hydroxyapatite carrier (BMPs- HA, bovine demineralized bone matrix (MB and coverage by a bovine collagen barrier membrane. The control defects were treated with MB-HA and covered by a bovine collagen membrane. The clinical measurements at six months after therapy in the test group revealed a reduction in the mean probing pocket depth (PPD of 1.63 ± 1.41mm (B and 1.93 ± 0.96mm (L and a mean change in the clinical attachment level (CAL of 1.60 ± 1.16mm (B and 1.46 ± 0.97mm (L. The control group showed a mean reduction of PPD of 1.93 ± 1.34mm (B and 2.0 ± 1.51mm (L and a mean change of CAL of 1.03 ± 1.24mm (B and 1.30 ± 1.14 mm (L. The analysis of variance (ANOVA demonstrated that the changes in the clinical parameters were statistically significant (pEste estudo teve como objetivo avaliar a aplicação do ''pool'' de BMPs bovinas no tratamento de defeitos intra-ósseos. A amostra constou de quinze indivíduos com idade entre 26 e 57 anos, apresentando um par de defeitos intra-ósseos comparáveis, localizados no mesmo arco em dentes do mesmo tipo (pré-molares ou molares e com perda de inserção (PI ³5mm. Em cada indivíduo, o defeito teste foi tratado com a associação ''pool'' de BMPs- carreador Hidroxiapatita reabsorvível (BMPs-HA, matriz orgânica bovina desmineralizada liofilizada (MO e barreira de colágeno bovino, enquanto os defeitos controle foram tratados com MO-HA e barreira de colágeno. Na avaliação clínica aos seis meses após a medida inicial, o grupo teste apresentou variação de profundidade de sondagem (PS de

Evaluation of charred porous polymers as a method of storm water pollution prevention for shipyards

Energy Technology Data Exchange (ETDEWEB)

Clark, G.E.

1998-08-01

Most shipyards have viable Best Management Practices (BMPs) in place to mitigate the transport of heavy metals to surface waters by storm water. Despite aggressive efforts to control storm water, shipyards have come under increased regulatory pressure to further reduce concentrations of heavy metals, such as copper and nickel, in storm water discharges. The tightening of regulatory requirements warrants research into additional BMPs. The objectives of this research project were to: (1) determine the feasibility of placing a replaceable cartridge of adsorbent material within a storm water collection system; and (2) evaluate two commercially available charred porous polymer adsorbents for the removal of heavy metals from storm water. The results indicated that there are commercially available storm water treatment components which could be adapted to house a cartridge of porous adsorbent material.

Get In and Get Out: Assessing Stream Sediment Loading from Short Duration Forest Harvest Operations and Rapid Haul Road Decommissioning.

Science.gov (United States)

Corrigan, A.; Silins, U.; Stone, M.

2016-12-01

Best management practices (BMPs) and associated erosion control measures for mitigating sediment impacts from forestry roads and road-stream crossings are well documented. While rapid road decommissioning after forestry operations may serve to limit broader impacts on sediment production in high value headwater streams, few studies have evaluated the combined effects of accelerated harvest operations and rapid retirement of logging roads and road-stream crossings on stream sediment. The objectives of this study were to evaluate the initial impacts of these strategies on fine sediment loading and fate during a short duration harvesting operation in 3 headwater sub-catchments in the southwestern Rocky Mountains of Alberta, Canada. A multi-pronged sampling approach (ISCOs, event focused grab sampling, continuous wash load sampling, and stream bed sediment intrusion measurements) was used to measure sediment loading and deposition in streambeds upstream and downstream of road-stream bridge crossings during harvest operations (2015) and after road and bridge crossing retirement (2016). Sediment production from forestry roads was generally much lower than has been reported from other studies in similar settings. Average total suspended solids (TSS) downstream of the bridge crossings were actually lower (-3.28 g/L; -0.704 g/L) than upstream of two bridge crossings while in-stream sediment sources contributed to elevated sediment downstream of a third road-stream crossing. Minimal in stream sediment impacts from forest harvest and road-stream crossings was likely a reflection of combined factors including a) employment of erosion control BMPs to roads and bridge crossings, b) rapid decommissioning of roads and crossings to limit exposure of linear land disturbance features, and c) drier El Niño climatic conditions during the study.

SUSTAIN - AN EPA BMP PROCESS AND PLACEMENT TOOL FOR URBAN WATERSHEDS

Science.gov (United States)

To assist stormwater management professionals in planning for implementation of best management practices (BMPs), efforts have been under way by the U.S. Environmental Protection Agency (EPA) since 2003 to develop a decision-support system for placement of BMPs at strategic locat...

Multiple-source multiple-harmonic active vibration control of variable section cylindrical structures: A numerical study

Science.gov (United States)

Liu, Jinxin; Chen, Xuefeng; Gao, Jiawei; Zhang, Xingwu

2016-12-01

Air vehicles, space vehicles and underwater vehicles, the cabins of which can be viewed as variable section cylindrical structures, have multiple rotational vibration sources (e.g., engines, propellers, compressors and motors), making the spectrum of noise multiple-harmonic. The suppression of such noise has been a focus of interests in the field of active vibration control (AVC). In this paper, a multiple-source multiple-harmonic (MSMH) active vibration suppression algorithm with feed-forward structure is proposed based on reference amplitude rectification and conjugate gradient method (CGM). An AVC simulation scheme called finite element model in-loop simulation (FEMILS) is also proposed for rapid algorithm verification. Numerical studies of AVC are conducted on a variable section cylindrical structure based on the proposed MSMH algorithm and FEMILS scheme. It can be seen from the numerical studies that: (1) the proposed MSMH algorithm can individually suppress each component of the multiple-harmonic noise with an unified and improved convergence rate; (2) the FEMILS scheme is convenient and straightforward for multiple-source simulations with an acceptable loop time. Moreover, the simulations have similar procedure to real-life control and can be easily extended to physical model platform.

Conference on alternatives for pollution control from coal-fired low emission sources, Plzen, Czech Republic. Plzen Proceedings

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

The Conference on Alternatives for Pollution Control from Coal-Fired Emission Sources presented cost-effective approaches for pollution control of low emission sources (LES). It also identified policies and strategies for implementation of pollution control measures at the local level. Plzen, Czech Republic, was chosen as the conference site to show participants first hand the LES problems facing Eastern Europe today. Collectively, these Proceedings contain clear reports on: (a) methods for evaluating the cost effectiveness of alternative approaches to control pollution from small coal-fired boilers and furnaces; (b) cost-effective technologies for controlling pollution from coal-fired boilers and furnaces; (c) case studies of assessment of cost effective pollution control measures for selected cities in eastern Europe; and (d) approaches for actually implementing pollution control measures in cities in Eastern Europe. It is intended that the eastern/central European reader will find in these Proceedings useful measures that can be applied to control emissions and clean the air in his city or region. The conference was sponsored by the United States Agency for International Development (AID), the United States Department of Energy (DOE), and the Czech Ministry of Industry and Trade. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

Modeling the effects of integrating larval habitat source reduction and insecticide treated nets for malaria control.

Directory of Open Access Journals (Sweden)

Laith Yakob

Full Text Available Integrated vector management for malaria control has received a lot of recent interest. Attacking multiple points in the transmission cycle is hoped to act synergistically and improve upon current single-tool interventions based on the use of insecticide-treated bed nets (ITNs. In the present study, we theoretically examined the application of larval habitat source reduction with ITNs in reducing malaria transmission. We selected this type of environmental management to complement ITNs because of a potential secondary mode of action that both control strategies share. In addition to increasing vector mortality, ITNs reduce the rate at which female mosquitoes locate human hosts for blood feeding, thereby extending their gonotrophic cycle. Similarly, while reducing adult vector emergence and abundance, source reduction of larval habitats may prolong the cycle duration by extending delays in locating oviposition sites. We found, however, that source reduction of larval habitats only operates through this secondary mode of action when habitat density is below a critical threshold. Hence, we illustrate how this strategy becomes increasingly effective when larval habitats are limited. We also demonstrate that habitat source reduction is better suited to human populations of higher density and in the presence of insecticide resistance or when the insecticidal properties of ITNs are depleted.

Eternal triangle: the interaction of light source, electrical control gear, and optics

Science.gov (United States)

S'heeren, Griet

1998-04-01

In this particular 'affair' the participants are less than human but have individual personalities they bring to their relationship with each other. High pressure metal halide lamps such as BriteArc lamps have the highest luminance and radiance of all continuously operating practical light source. Since these lamps have short arcs and are available in power ratings from about 30W to 30kW they have found applications with various optical systems. Besides the lamps, such systems include an electrical control device and an optical system. To fulfil the user's requirements for a specific application, it is not only important to choose the right lamp, but crucial to achieve a harmonious marriage between the light source, electrical control device and the optics. To run a high pressure discharge lamp an ignitor/ballast system is essential This stabilizes the lamp parameters. The chemical components inside the lamp determine the lamp voltage and the gear determines, via the current, the lamp power. These are directly related in the luminance and color temperature of the emitted light. Therefore lamp performance and effective life are dependent on the ignitor, control gear and lamp combination. Since the lamp emits radiation in all directions, collection of the light from a lamp can be improved by using reflectors to deliver the light into a lens system. Since lamps with short arc gaps approach a point source they appear ideal for optical system applications. The shape of the reflector and the focusing of the lamp determine which part of the light is collected out of the light-arc. In the case of an LCD projector, the final light output also depends on the transmission characteristics of the LCD panels. Their nonlinearity causes the color of the emitted light to be different from the lamp color. All these parameters have to be optimized to obtain the highest performance. This leads to the conclusion that a carefully matched combination of lamp, ignitor/ballast and optics

Fault diagnosis and fault-tolerant finite control set-model predictive control of a multiphase voltage-source inverter supplying BLDC motor.

Science.gov (United States)

Salehifar, Mehdi; Moreno-Equilaz, Manuel

2016-01-01

Due to its fault tolerance, a multiphase brushless direct current (BLDC) motor can meet high reliability demand for application in electric vehicles. The voltage-source inverter (VSI) supplying the motor is subjected to open circuit faults. Therefore, it is necessary to design a fault-tolerant (FT) control algorithm with an embedded fault diagnosis (FD) block. In this paper, finite control set-model predictive control (FCS-MPC) is developed to implement the fault-tolerant control algorithm of a five-phase BLDC motor. The developed control method is fast, simple, and flexible. A FD method based on available information from the control block is proposed; this method is simple, robust to common transients in motor and able to localize multiple open circuit faults. The proposed FD and FT control algorithm are embedded in a five-phase BLDC motor drive. In order to validate the theory presented, simulation and experimental results are conducted on a five-phase two-level VSI supplying a five-phase BLDC motor. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Risk of gastric cancer by water source: evidence from the Golestan case-control study.

Directory of Open Access Journals (Sweden)

Laura Eichelberger

Full Text Available Gastric cancer (GC is the world's fifth most common cancer, and the third leading cause of cancer-related death. Over 70% of incident cases and deaths occur in developing countries. We explored whether disparities in access to improved drinking water sources were associated with GC risk in the Golestan Gastric Cancer Case Control Study.306 cases and 605 controls were matched on age, gender, and place of residence. We conducted unconditional logistic regression to calculate odds ratios (ORs and 95% confidence intervals (CI, adjusted for age, gender, ethnicity, marital status, education, head of household education, place of birth and residence, homeownership, home size, wealth score, vegetable consumption, and H. pylori seropositivity. Fully-adjusted ORs were 0.23 (95% CI: 0.05-1.04 for chlorinated well water, 4.58 (95% CI: 2.07-10.16 for unchlorinated well water, 4.26 (95% CI: 1.81-10.04 for surface water, 1.11 (95% CI: 0.61-2.03 for water from cisterns, and 1.79 (95% CI: 1.20-2.69 for all unpiped sources, compared to in-home piped water. Comparing unchlorinated water to chlorinated water, we found over a two-fold increased GC risk (OR 2.37, 95% CI: 1.56-3.61.Unpiped and unchlorinated drinking water sources, particularly wells and surface water, were significantly associated with the risk of GC.

Symptoms and sources of Yersinia enterocolitica-infection: a case-control study

Directory of Open Access Journals (Sweden)

Siitonen Anja

2010-05-01

Full Text Available Abstract Background Yersinia enterocolitica (YE is the causative agent of yersiniosis. YE encompass strains of diverse pathogenicity: YE biotypes 1B and 2-5 are considered pathogenic, whereas biotype 1A is in general considered nonvirulent. Also YE-like species, which can sometimes be misidentified as YE, are considered nonvirulent. Methods In order to study differences in clinical picture caused by different YE types and their possible sources a case-control study was conducted in 2006. In this case-control study, 295 case-patients with YE or YE-like finding and their 758 controls responded to the questionnaire about symptoms and possible sources of infection. Results Strains of pathogenic YE bio/serotypes 3-4/O:3 or 2/O:9 were found in 18%, YE biotype 1A in 65% and YE -like strains of 17% of the patients. Patients infected with the strains of pathogenic YE bio/serotypes were younger and had fever more often than those with BT 1A who suffered more from vomiting. Symptoms of reactive arthritis were reported by 10% of pathogenic YE infections, 3% of YE BT 1A, and 0.3% of the controls. Eating or tasting raw or medium done pork was a significant risk factor for pathogenic YE bio/serotype infection (OR 6.6; 95% CI 1.7-24.9 as well as eating in a canteen (OR 3.5; 95% CI 1.6-7.9. Imported fruits and berries were associated with increased risk of YE BT 1A finding. Conclusions The symptoms of the patients with YE BT 1A differed from yersiniosis caused by the classic pathogenic YE bio/serotypes. In addition, the patients with YE BT 1A had more protracted gastrointestinal disorders and unspecific complaints. Small children were overrepresented in classic pathogenic bio/serotypes while in BT 1A or YE-like species were not found among children younger than two years. This suggests the lacking virulence of the BT 1A strains. We can not, however, rule out the possibility that some strains of genetically heterogeneous group of BT 1A may cause an illness.

Radiation Safety and Orphan Sources

International Nuclear Information System (INIS)

Janzekovic, H.; Krizman, M.

2006-01-01

The wide spread use of radioactive and particularly of nuclear materials which started in the last century very quickly also demonstrated negative sides. The external exposure and radiotoxicity of these materials could be easily used in a malevolent act. Due to the fact that these materials could not be detected without special equipment designed for that purpose, severe control over their use in all phases of a life cycle is required. An orphan source is a radioactive source which is not under regulatory control, either because it has never been under regulatory or because it has been abandoned, lost, misplaced, stolen or transferred without proper authorization. In the last ten years a few international conferences were dedicated to the improvement of the safety and security of radioactive sources. Three main tasks are focused, the maintenance of data bases related to events with orphan sources and the publications of such events, the preparation of recommendations and guidelines to national regulatory bodies in order to prevent and detect the events related to orphan sources as well as to develop the response strategies to radiological or nuclear emergency, appraisals of the national strategies of radioactive sources control. Concerning Slovenia, strengthening control over orphan sources in Slovenia started after the adoption of new legislation in 2002. It was carried out through several tasks with the aim to prevent orphan sources, as well as to identify the sources which could be potentially orphan sources. The comprehensive methodology was developed by the Slovenian nuclear safety administration (S.N.S.A.) based on international guidelines as well as on the study of national lesson learned cases. The methodology was developed and used in close cooperation with all parties involved, namely other regulatory authorities, police, customs, agency for radioactive waste management (A.R.A.O.), technical support organisations (T.S.O.), users of source, authorised

Radiation Safety and Orphan Sources

Energy Technology Data Exchange (ETDEWEB)

Janzekovic, H.; Krizman, M. [Slovenian Nuclear Safety Administration, Ljubljana (Slovenia)

2006-07-01

The wide spread use of radioactive and particularly of nuclear materials which started in the last century very quickly also demonstrated negative sides. The external exposure and radiotoxicity of these materials could be easily used in a malevolent act. Due to the fact that these materials could not be detected without special equipment designed for that purpose, severe control over their use in all phases of a life cycle is required. An orphan source is a radioactive source which is not under regulatory control, either because it has never been under regulatory or because it has been abandoned, lost, misplaced, stolen or transferred without proper authorization. In the last ten years a few international conferences were dedicated to the improvement of the safety and security of radioactive sources. Three main tasks are focused, the maintenance of data bases related to events with orphan sources and the publications of such events, the preparation of recommendations and guidelines to national regulatory bodies in order to prevent and detect the events related to orphan sources as well as to develop the response strategies to radiological or nuclear emergency, appraisals of the national strategies of radioactive sources control. Concerning Slovenia, strengthening control over orphan sources in Slovenia started after the adoption of new legislation in 2002. It was carried out through several tasks with the aim to prevent orphan sources, as well as to identify the sources which could be potentially orphan sources. The comprehensive methodology was developed by the Slovenian nuclear safety administration (S.N.S.A.) based on international guidelines as well as on the study of national lesson learned cases. The methodology was developed and used in close cooperation with all parties involved, namely other regulatory authorities, police, customs, agency for radioactive waste management (A.R.A.O.), technical support organisations (T.S.O.), users of source, authorised

User friendly tools to target vulnerable areas at watershed scale: evaluation of the soil vulnerability and conductivity claypan indices

Science.gov (United States)

One finding of the Conservation Effects Assessment Program (CEAP) watershed studies was that Best Management practices (BMPs) were not always installed where most needed: in many watersheds, only a fraction of BMPs were implemented in the most vulnerable areas. While complex computer simulation mode...

Serum Proteases Potentiate BMP-Induced Cell Cycle Re-entry of Dedifferentiating Muscle Cells during Newt Limb Regeneration

NARCIS (Netherlands)

Wagner, Ines; Wang, Heng; Weissert, Philipp M.; Straube, Werner L.; Shevchenko, Anna; Gentzel, Marc; Brito, Goncalo; Tazaki, Akira; Oliveira, Catarina; Sugiura, Takuji; Shevchenko, Andrej; Simon, Andras; Drechsel, David N.; Tanaka, Elly M.

2017-01-01

Limb amputation in the newt induces myofibers to dedifferentiate and re-enter the cell cycle to generate proliferative myogenic precursors in the regeneration blastema. Here we show that bone morphogenetic proteins (BMPs) and mature BMPs that have been further cleaved by serum proteases induce cell

Controlling composition and color characteristics of Monascus pigments by pH and nitrogen sources in submerged fermentation.

Science.gov (United States)

Shi, Kan; Song, Da; Chen, Gong; Pistolozzi, Marco; Wu, Zhenqiang; Quan, Lei

2015-08-01

Submerged fermentations of Monascus anka were performed with different nitrogen sources at different pH in 3 L bioreactors. The results revealed that the Monascus pigments dominated by different color components (yellow pigments, orange pigments or red pigments) could be selectively produced through pH control and nitrogen source selection. A large amount of intracellular pigments dominated by orange pigments and a small amount of water-soluble extracellular yellow pigments were produced at low pH (pH 2.5 and 4.0), independently of the nitrogen source employed. At higher pH (pH 6.5), the role of the nitrogen source became more significant. In particular, when ammonium sulfate was used as nitrogen source, the intracellular pigments were dominated by red pigments with a small amount of yellow pigments. Conversely, when peptone was used, intracellular pigments were dominated by yellow pigments with a few red pigments derivatives. Neither the presence of peptone nor ammonium sulfate promoted the production of intracellular orange pigments while extracellular pigments with an orangish red color were observed in both cases, with a higher yield when peptone was used. Two-stage pH control fermentation was then performed to improve desirable pigments yield and further investigate the effect of pH and nitrogen sources on pigments composition. These results provide a useful strategy to produce Monascus pigments with different composition and different color characteristics. Copyright © 2015 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Plasma shape control by pulsed solenoid on laser ion source

International Nuclear Information System (INIS)

Sekine, M.; Ikeda, S.; Romanelli, M.; Kumaki, M.; Fuwa, Y.; Kanesue, T.; Hayashizaki, N.; Lambiase, R.; Okamura, M.

2015-01-01

A Laser ion source (LIS) provides high current heavy ion beams with a very simple mechanical structure. Plasma is produced by a pulsed laser ablation of a solid state target and ions are extracted by an electric field. However, it was difficult to manipulate the beam parameters of a LIS, since the plasma condition could only be adjusted by the laser irradiation condition. To enhance flexibility of LIS operation, we employed a pulsed solenoid in the plasma drift section and investigated the effect of the solenoid field on singly charged iron beams. The experimentally obtained current profile was satisfactorily controlled by the pulsed magnetic field. This approach may also be useful to reduce beam emittance of a LIS

Plasma shape control by pulsed solenoid on laser ion source

Science.gov (United States)

Sekine, M.; Ikeda, S.; Romanelli, M.; Kumaki, M.; Fuwa, Y.; Kanesue, T.; Hayashizaki, N.; Lambiase, R.; Okamura, M.

2015-09-01

A Laser ion source (LIS) provides high current heavy ion beams with a very simple mechanical structure. Plasma is produced by a pulsed laser ablation of a solid state target and ions are extracted by an electric field. However, it was difficult to manipulate the beam parameters of a LIS, since the plasma condition could only be adjusted by the laser irradiation condition. To enhance flexibility of LIS operation, we employed a pulsed solenoid in the plasma drift section and investigated the effect of the solenoid field on singly charged iron beams. The experimentally obtained current profile was satisfactorily controlled by the pulsed magnetic field. This approach may also be useful to reduce beam emittance of a LIS.

Plasma shape control by pulsed solenoid on laser ion source

Energy Technology Data Exchange (ETDEWEB)

Sekine, M. [Tokyo Institute of Technology, Meguro-ku, Tokyo 2-12-1 (Japan); RIKEN, Wako, Saitama 351-0198 (Japan); Ikeda, S. [Tokyo Institute of Technology, Yokohama, Kanagawa 226-8502 (Japan); RIKEN, Wako, Saitama 351-0198 (Japan); Romanelli, M. [Cornell University, Ithaca, NY 14850 (United States); Kumaki, M. [RIKEN, Wako, Saitama 351-0198 (Japan); Waseda University, Shinjuku, Tokyo 169-0072 (Japan); Fuwa, Y. [RIKEN, Wako, Saitama 351-0198 (Japan); Kyoto University, Uji, Kyoto 611-0011 (Japan); Kanesue, T. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Hayashizaki, N. [Tokyo Institute of Technology, Meguro-ku, Tokyo 2-12-1 (Japan); Lambiase, R. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Okamura, M. [RIKEN, Wako, Saitama 351-0198 (Japan); Brookhaven National Laboratory, Upton, NY 11973 (United States)

2015-09-21

A Laser ion source (LIS) provides high current heavy ion beams with a very simple mechanical structure. Plasma is produced by a pulsed laser ablation of a solid state target and ions are extracted by an electric field. However, it was difficult to manipulate the beam parameters of a LIS, since the plasma condition could only be adjusted by the laser irradiation condition. To enhance flexibility of LIS operation, we employed a pulsed solenoid in the plasma drift section and investigated the effect of the solenoid field on singly charged iron beams. The experimentally obtained current profile was satisfactorily controlled by the pulsed magnetic field. This approach may also be useful to reduce beam emittance of a LIS.

Basolateral BMP signaling in polarized epithelial cells.

Directory of Open Access Journals (Sweden)

Masao Saitoh

Full Text Available Bone morphogenetic proteins (BMPs regulate various biological processes, mostly mediated by cells of mesenchymal origin. However, the roles of BMPs in epithelial cells are poorly understood. Here, we demonstrate that, in polarized epithelial cells, BMP signals are transmitted from BMP receptor complexes exclusively localized at the basolateral surface of the cell membrane. In addition, basolateral stimulation with BMP increased expression of components of tight junctions and enhanced the transepithelial resistance (TER, counteracting reduction of TER by treatment with TGF-β or an anti-tumor drug. We conclude that BMPs maintain epithelial polarity via intracellular signaling from basolaterally localized BMP receptors.

Analysis of Best Management Practices Implementation on Water Quality Using the Soil and Water Assessment Tool

Directory of Open Access Journals (Sweden)

Jason Motsinger

2016-04-01

Full Text Available The formation of hypoxic zone in the Gulf of Mexico can be traced to agricultural watersheds in the Midwestern United States that are artificially drained in order to make the land suitable for agriculture. A number of best management practices (BMPs have been introduced to improve the water quality in the region but their relative effectivenss of these BMPs in reducing nutrient load has not been properly quantified. In order to determine the BMPs useful for reducing nutrient discharge from a tile drained watershed, a Soil and Water Assessment Tool (SWAT model was calibrated and validated for water flow and nitrate load using experimental data from the Little Vermillion River (LVR watershed in east-central Illinois. Then, the performance of four common BMPs (reduced tillage, cover crop, filter strip and wetlands were evaluated. For BMPs, the usage of rye as cover crop performed the best in reducing nitrate discharge from the watershed as a single BMP, with an average annual nitrate load reduction of 54.5%. Combining no tillage and rye cover crops had varying results over the period simulated, but the average nitrate reduction was better than using rye cover crops with conventional tillage, with the average annual nitrate discharge decreased by 60.5% (an improvement of 13% over rye only.

Mosquito larval source management for controlling malaria

Science.gov (United States)

Tusting, Lucy S; Thwing, Julie; Sinclair, David; Fillinger, Ulrike; Gimnig, John; Bonner, Kimberly E; Bottomley, Christian; Lindsay, Steven W

2015-01-01

Background Malaria is an important cause of illness and death in people living in many parts of the world, especially sub-Saharan Africa. Long-lasting insecticide treated bed nets (LLINs) and indoor residual spraying (IRS) reduce malaria transmission by targeting the adult mosquito vector and are key components of malaria control programmes. However, mosquito numbers may also be reduced by larval source management (LSM), which targets mosquito larvae as they mature in aquatic habitats. This is conducted by permanently or temporarily reducing the availability of larval habitats (habitat modification and habitat manipulation), or by adding substances to standing water that either kill or inhibit the development of larvae (larviciding). Objectives To evaluate the effectiveness of mosquito LSM for preventing malaria. Search methods We searched the Cochrane Infectious Diseases Group Specialized Register; Cochrane Central Register of Controlled Trials (CENTRAL); MEDLINE; EMBASE; CABS Abstracts; and LILACS up to 24 October 2012. We handsearched the Tropical Diseases Bulletin from 1900 to 2010, the archives of the World Health Organization (up to 11 February 2011), and the literature database of the Armed Forces Pest Management Board (up to 2 March 2011). We also contacted colleagues in the field for relevant articles. Selection criteria We included cluster randomized controlled trials (cluster-RCTs), controlled before-and-after trials with at least one year of baseline data, and randomized cross-over trials that compared LSM with no LSM for malaria control. We excluded trials that evaluated biological control of anopheline mosquitoes with larvivorous fish. Data collection and analysis At least two authors assessed each trial for eligibility. We extracted data and at least two authors independently determined the risk of bias in the included studies. We resolved all disagreements through discussion with a third author. We analyzed the data using Review Manager 5 software

Optimized Controller Design for a 12-Pulse Voltage Source Converter Based HVDC System

Science.gov (United States)

Agarwal, Ruchi; Singh, Sanjeev

2017-12-01

The paper proposes an optimized controller design scheme for power quality improvement in 12-pulse voltage source converter based high voltage direct current system. The proposed scheme is hybrid combination of golden section search and successive linear search method. The paper aims at reduction of current sensor and optimization of controller. The voltage and current controller parameters are selected for optimization due to its impact on power quality. The proposed algorithm for controller optimizes the objective function which is composed of current harmonic distortion, power factor, and DC voltage ripples. The detailed designs and modeling of the complete system are discussed and its simulation is carried out in MATLAB-Simulink environment. The obtained results are presented to demonstrate the effectiveness of the proposed scheme under different transient conditions such as load perturbation, non-linear load condition, voltage sag condition, and tapped load fault under one phase open condition at both points-of-common coupling.

A Distributed Monitoring and Control System for the Laser Ion Source RILIS at CERN-ISOLDE

CERN Document Server

AUTHOR|(SzGeCERN)715185; Richter, Detlef; Wendt, Klaus

In this work, the implementation of the LabVIEW-based RILIS Equipment Acquisition and Control Toolset (REACT) software framework is documented, revised, and further developed to accomplish remotely operated in-source laser spectroscopy experiments at CERN-ISOLDE. The Resonance Ionization Laser Ion Source (RILIS) is an integral part of the radioactive ion beam user facility ISOLDE at CERN. Its task as an ion source is to ensure high isobaric purity and production efficiency of the ion beams that are generated for the various experimental setups of the facility. Reliable operation requires directing 3 pulsed laser beams, precisely wavelength-tuned and overlapped in time to a precision of 5 nanoseconds, to converge into a 3mm diameter ion source cavity located 25m away in an inaccessible radioactive environment. These stable conditions have to be maintained for up to 7 days at a time per experiment setup. Within recent years, the array of RILIS equipment and its need to interface with other experimental apparatu...

Groundwater and stream response times to fertility management changes in pastures

Science.gov (United States)

To assess the effectiveness of best-management practices (BMPs), measurements need to be made to determine how the implementation of BMPs affect water quality and soil loss from the areas receiving the practices. For large watersheds (multiple square miles in area) this is a difficult, expensive, a...

Dead beat filling and feedforward rf control for the spallation neutron source SNQ

International Nuclear Information System (INIS)

Schulze, D.

1982-01-01

For the 1.1 GeV-100 mA Spallation Neutron Source SNQ operation costs and beam losses ask for the possible potential of rf control improvements. Two novel methods are investigated. First, in order to increase the overall rf efficiency, the cavity field is built up as fast as possible in the open loop state of feedback control and in detuned position of the cavity in such a manner that the cavity with beam is matched to the generator. It is shown that this requires the simulataneous application of a generator amplitude and a generator phase step. Secondly, a feedforward control system is proposed, which reduces the amplitude and phase control error caused by an arbitrary beam transient into the limits of +-0.1% and +-0.1 0 and maintains these error limits also in the presence of parameter drift. This is done by an adaptive parameter adjustment procedure using a digital model of the control system. The system structure and a promising digital simulation are discussed

Voltage control in Z-source inverter using low cost microcontroller for undergraduate approach

Science.gov (United States)

Zulkifli, Shamsul Aizam; Sewang, Mohd Rizal; Salimin, Suriana; Shah, Noor Mazliza Badrul

2017-09-01

This paper is focussing on controlling the output voltage of Z-Source Inverter (ZSI) using a low cost microcontroller with MATLAB-Simulink that has been used for interfacing the voltage control at the output of ZSI. The key advantage of this system is the ability of a low cost microcontroller to process the voltage control blocks based on the mathematical equations created in MATLAB-Simulink. The Proportional Integral (PI) control equations are been applied and then, been downloaded to the microcontroller for observing the changes on the voltage output regarding to the changes on the reference on the PI. The system has been simulated in MATLAB and been verified with the hardware setup. As the results, the Raspberry Pi and Arduino that have been used in this work are able to respond well when there is a change of ZSI output. It proofed that, by applying/introducing this method to student in undergraduate level, it will help the student to understand more on the process of the power converter combine with a control feedback function that can be applied at low cost microcontroller.

Controlled isotropic fission fragment sources on the base of nuclear-physical facilities

International Nuclear Information System (INIS)

Sevast'yanov, V.D.; Maslov, G.N.

1995-01-01

Isotropic fission fragment sources (IFFS) are developed on the base of a neutron generator and pulse fast reactor. IFFS permit to calibrate fission fragment detectors. The IFFS consist of radiators with 235 U. The radiators are placed in a thermal neutron field of the neutron generator or in the reactor core center. The fragment activity is controlled by indications of an α-particle counter or by indications of a monitor of energy release in the core. 14 refs.; 1 fig.; 1 tab

A frequency controlled LCL - T resonant converter for H- ion source

International Nuclear Information System (INIS)

Gauttam, V.K.; Kasliwal, A.; Banwari, R.; Pandit, T.G.; Thakurta, A.C.

2013-01-01

An H - ion source is being developed at Raja Ramanna Centre for Advanced Technology, Indore. An LCL-T resonant power converter with variable frequency control is proposed which is utilized to develop a -20 kV/100 mA high voltage (HV) power supply for extraction of H - ions. The LCL-T resonant topology offers many advantages like gainful utilization of the transformer parasitics as a part of resonant network and low circulating current. The power converter is operated with variable frequency control and above resonance to get well known zero-voltage switching (ZVS) advantages for full bridge semiconductor switches in full load range. The converter energizes the symmetrical Cockcroft-Walton (CW) based HV generator to achieve required high voltage. The CW circuit is an attractive solution for HV generation since it has features like low stored energy and low output ripple. The HV power supply is operated in constant current (CC) mode with closed loop control and soft start of the power supply is achieved by sweeping the switching frequency from 40 kHz to defined operating point. Design parameters, simulation results and experimental results of the power converter are presented in this paper. (author)

Spectrometer control subsystem with high level functionality for use at the National Synchrotron Light Source

International Nuclear Information System (INIS)

Alberi, J.L.; Stubblefield, F.W.

1980-11-01

We have developed a subsystem capable of controlling stepping motors in a wide variety of vuv and x-ray spectrometers to be used at the National Sychrotron Light Source. The subsystem is capable of controlling up to 15 motors with encoder readback and ramped acceleration/deceleration. Both absolute and incremental encoders may be used in any mixture. Function commands to the subsystem are communicated via ASCII characters over an asynchronous serial link in a well-defined protocol in decipherable English. Thus the unit can be controlled via write statements in a high-level language. Details of hardware implementation will be presented

Development of Load Duration Curve System in Data Scarce Watersheds Based on a Distributed Hydrological Model

Science.gov (United States)

WANG, J.

2017-12-01

In stream water quality control, the total maximum daily load (TMDL) program is very effective. However, the load duration curves (LDC) of TMDL are difficult to be established because no sufficient observed flow and pollutant data can be provided in data-scarce watersheds in which no hydrological stations or consecutively long-term hydrological data are available. Although the point sources or a non-point sources of pollutants can be clarified easily with the aid of LDC, where does the pollutant come from and to where it will be transported in the watershed cannot be traced by LDC. To seek out the best management practices (BMPs) of pollutants in a watershed, and to overcome the limitation of LDC, we proposed to develop LDC based on a distributed hydrological model of SWAT for the water quality management in data scarce river basins. In this study, firstly, the distributed hydrological model of SWAT was established with the scarce-hydrological data. Then, the long-term daily flows were generated with the established SWAT model and rainfall data from the adjacent weather station. Flow duration curves (FDC) was then developed with the aid of generated daily flows by SWAT model. Considering the goal of water quality management, LDC curves of different pollutants can be obtained based on the FDC. With the monitored water quality data and the LDC curves, the water quality problems caused by the point or non-point source pollutants in different seasons can be ascertained. Finally, the distributed hydrological model of SWAT was employed again to tracing the spatial distribution and the origination of the pollutants of coming from what kind of agricultural practices and/or other human activities. A case study was conducted in the Jian-jiang river, a tributary of Yangtze river, of Duyun city, Guizhou province. Results indicate that this kind of method can realize the water quality management based on TMDL and find out the suitable BMPs for reducing pollutant in a watershed.

Advanced controls for light sources

Science.gov (United States)

Biedron, S. G.; Edelen, A. L.; Milton, S. V.

2016-09-01

We present a summary of our team's recent efforts in developing adaptive, artificial intelligence-inspired techniques specifically to address several control challenges that arise in machines/systems including those in particle accelerator systems. These techniques can readily be adapted to other systems such as lasers, beamline optics, etc… We are not at all suggesting that we create an autonomous system, but create a system with an intelligent control system, that can continually use operational data to improve itself and combines both traditional and advanced techniques. We believe that the system performance and reliability can be increased based on our findings. Another related point is that the controls sub-system of an overall system is usually not the heart of the system architecture or design process. More bluntly, often times all of the peripheral systems are considered as secondary to the main system components in the architecture design process because it is assumed that the controls system will be able to "fix" challenges found later with the sub-systems for overall system operation. We will show that this is not always the case and that it took an intelligent control application to overcome a sub-system's challenges. We will provide a recent example of such a "fix" with a standard controller and with an artificial intelligence-inspired controller. A final related point to be covered is that of system adaptation for requirements not original to a system's original design.

Impedance source power electronic converters

CERN Document Server

Liu, Yushan; Ge, Baoming; Blaabjerg, Frede; Ellabban, Omar; Loh, Poh Chiang

2016-01-01

Impedance Source Power Electronic Converters brings together state of the art knowledge and cutting edge techniques in various stages of research related to the ever more popular impedance source converters/inverters. Significant research efforts are underway to develop commercially viable and technically feasible, efficient and reliable power converters for renewable energy, electric transportation and for various industrial applications. This book provides a detailed understanding of the concepts, designs, controls, and application demonstrations of the impedance source converters/inverters. Key features: Comprehensive analysis of the impedance source converter/inverter topologies, including typical topologies and derived topologies. Fully explains the design and control techniques of impedance source converters/inverters, including hardware design and control parameter design for corresponding control methods. Presents the latest power conversion solutions that aim to advance the role of pow...

[The role of Smads and related transcription factors in the signal transduction of bone morphogenetic protein inducing bone formation].

Science.gov (United States)

Xu, Xiao-liang; Dai, Ke-rong; Tang, Ting-ting

2003-09-01

To clarify the mechanisms of the signal transduction of bone morphogenetic proteins (BMPs) inducing bone formation and to provide theoretical basis for basic and applying research of BMPs. We looked up the literature of the role of Smads and related transcription factors in the signal transduction of BMPs inducing bone formation. The signal transduction processes of BMPs included: 1. BMPs combined with type II and type I receptors; 2. the type I receptor phosphorylated Smads; and 3. Smads entered the cell nucleus, interacted with transcription factors and influenced the transcription of related proteins. Smads could be divided into receptor-regulated Smads (R-Smads: Smad1, Smad2, Smad3, Smad5, Smad8 and Smad9), common-mediator Smad (co-Smad: Smad4), and inhibitory Smads (I-Smads: Smad6 and Smad7). Smad1, Smad5, Smad8, and probable Smad9 were involved in the signal transduction of BMPs. Multiple kinases, such as focal adhesion kinase (FAK), Ras-extracellular signal-regulated kinase (ERK), phosphatidylinositol 3-kinase (PI3K), and Akt serine/threonine kinase were related to Smads signal transduction. Smad1 and Smad5 related with transcription factors included core binding factor A1 (CBFA1), smad-interacting protein 1 (SIP1), ornithine decarboxylase antizyme (OAZ), activating protein-1 (AP-1), xenopus ventralizing homeobox protein-2 (Xvent-2), sandostatin (Ski), antiproliferative proteins (Tob), and homeodomain-containing transcriptian factor-8 (Hoxc-8), et al. CBFA1 could interact with Smad1, Smad2, Smad3, and Smad5, so it was involved in TGF-beta and BMP-2 signal transduction, and played an important role in the bone formation. Cleidocranial dysplasia (CCD) was thought to be caused by heterozygous mutations in CBFA1. The CBFA1 knockout mice showed no osteogenesis and had maturational disturbance of chondrocytes. Smads and related transcription factors, especially Smad1, Smad5, Smad8 and CBFA1, play an important role in the signal transduction of BMPs inducing bone

Mine Waste Technology Program. In Situ Source Control Of Acid Generation Using Sulfate-Reducing Bacteria

Science.gov (United States)

This report summarizes the results of the Mine Waste Technology Program (MWTP) Activity III, Project 3, In Situ Source Control of Acid Generation Using Sulfate-Reducing Bacteria, funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by EPA and the U.S....

Spallation Neutron Source Drift Tube Linac Resonance Control Cooling System Modeling

CERN Document Server

Tang, Johnny Y; Champion, Marianne M; Feschenko, Alexander; Gibson, Paul; Kiselev, Yuri; Kovalishin, A S; Kravchuk, Leonid V; Kvasha, Adolf; Schubert, James P

2005-01-01

The Resonance Control Cooling System (RCCS) for the warm linac of the Spallation Neutron Source was designed by Los Alamos National Laboratory. The primary design focus was on water cooling of individual component contributions. The sizing the RCCS water skid was accomplished by means of a specially created SINDA/FLUINT model tailored to these system requirements. A new model was developed in Matlab Simulink and incorporates actual operational values and control valve interactions. Included is the dependence of RF input power on system operation, cavity detuning values during transients, time delays that result from water flows through the heat exchanger, the dynamic process of water warm-up in the cooling system due to dissipated RF power on the cavity surface, differing contributions on the cavity detuning due to drift tube and wall heating, and a dynamic model of the heat exchanger with characteristics in close agreement to the real unit. Because of the Matlab Simulink model, investigation of a wide range ...

Modeling, analysis, and design of stationary reference frame droop controlled parallel three-phase voltage source inverters

DEFF Research Database (Denmark)

Vasquez, Juan Carlos; Guerrero, Josep M.; Savaghebi, Mehdi

2011-01-01

and discussed. Experimental results are provided to validate the performance and robustness of the VSIs functionality during Islanded and grid-connected operations, allowing a seamless transition between these modes through control hierarchies by regulating frequency and voltage, main-grid interactivity......Power electronics based microgrids consist of a number of voltage source inverters (VSIs) operating in parallel. In this paper, the modeling, control design, and stability analysis of three-phase VSIs are derived. The proposed voltage and current inner control loops and the mathematical models...

pH control for enhanced reductive bioremediation of chlorinated solvent source zones

International Nuclear Information System (INIS)

Robinson, Clare; Barry, D.A.; McCarty, Perry L.; Gerhard, Jason I.; Kouznetsova, Irina

2009-01-01

Enhanced reductive dehalogenation is an attractive treatment technology for in situ remediation of chlorinated solvent DNAPL source areas. Reductive dehalogenation is an acid-forming process with hydrochloric acid and also organic acids from fermentation of the electron donors typically building up in the source zone during remediation. This can lead to groundwater acidification thereby inhibiting the activity of dehalogenating microorganisms. Where the soils' natural buffering capacity is likely to be exceeded, the addition of an external source of alkalinity is needed to ensure sustained dehalogenation. To assist in the design of bioremediation systems, an abiotic geochemical model was developed to provide insight into the processes influencing the groundwater acidity as dehalogenation proceeds, and to predict the amount of bicarbonate required to maintain the pH at a suitable level for dehalogenating bacteria (i.e., > 6.5). The model accounts for the amount of chlorinated solvent degraded, site water chemistry, electron donor, alternative terminal electron-accepting processes, gas release and soil mineralogy. While calcite and iron oxides were shown to be the key minerals influencing the soil's buffering capacity, for the extensive dehalogenation likely to occur in a DNAPL source zone, significant bicarbonate addition may be necessary even in soils that are naturally well buffered. Results indicated that the bicarbonate requirement strongly depends on the electron donor used and availability of competing electron acceptors (e.g., sulfate, iron (III)). Based on understanding gained from this model, a simplified model was developed for calculating a preliminary design estimate of the bicarbonate addition required to control the pH for user-specified operating conditions.

External Carbon Source Addition as a Means to Control an Activated Sludge Nutrient Removal Process

DEFF Research Database (Denmark)

Isaacs, Steven Howard; Henze, Mogens; Søeberg, Henrik

1994-01-01

In alternating type activated sludge nutrient removal processes, the denitrification rate can be limited by the availability of readily-degradable carbon substrate. A control strategy is proposed by which an easily metabolizable COD source is added directly to that point in the process at which d...

Form-deprivation myopia induces decreased expression of bone morphogenetic protein-2, 5 in guinea pig sclera

Directory of Open Access Journals (Sweden)

Qing Wang

2015-02-01

Full Text Available AIM: To identify the presence of various bone morphogenetic proteins (BMPs and their receptors in normal sclera of human, rat and guinea pigs, and to determine whether their expression changed with form-deprivation myopia (FDM in guinea pig sclera. METHODS: The expression of BMPs and BMP receptors were detected using reverse transcription polymerase chain reaction (RT-PCR and immunofluorescence. Two-week-old guinea pigs were monocularly form-deprived with a translucent lens. After fourteen days induction of FDM, total RNA was isolated and subjected to RT-PCR to examine the changes of BMPs and BMP receptors in tissues from the posterior sclera. Western blotting analysis was used to investigate their changes in protein levels. RESULTS: Human sclera expressed mRNAs for BMP-2, -4, -5, -7, -RIA, -RIB and BMP-RII. Conversely, rat sclera only expressed mRNA for BMP-7 and BMP-RIB, while the expression of BMPs and BMP receptors in guinea pigs were similar to that of humans. Human sclera also expresses BMP-2, -4, -5,-7 in protein level. Fourteen days after the induction of myopia, significant decreased expressions for BMP-2 and BMP-5 in the posterior sclera of FDM-affected eyes (PCONCLUSION: Various BMPs were expressed in human and guinea pig sclera. In the posterior sclera, expressions of BMP-2 and BMP-5 significantly decreased in FDM eyes. This finding indicates that various BMPs as components of the scleral cytokines regulating tissue homeostasis and provide evidence that alterations in the expression of BMP-2 and BMP-5 are associated with sclera remodeling during myopia induction.

Impedance Source Power Electronic Converters

DEFF Research Database (Denmark)

Liu, Yushan; Abu-Rub, Haitham; Ge, Baoming

Impedance Source Power Electronic Converters brings together state of the art knowledge and cutting edge techniques in various stages of research related to the ever more popular impedance source converters/inverters. Significant research efforts are underway to develop commercially viable...... and technically feasible, efficient and reliable power converters for renewable energy, electric transportation and for various industrial applications. This book provides a detailed understanding of the concepts, designs, controls, and application demonstrations of the impedance source converters/inverters. Key...... features: Comprehensive analysis of the impedance source converter/inverter topologies, including typical topologies and derived topologies. Fully explains the design and control techniques of impedance source converters/inverters, including hardware design and control parameter design for corresponding...

Regulatory Control of Radiation Sources. Safety Guide (Arabic Edition)

International Nuclear Information System (INIS)

2012-01-01

This Safety Guide is intended to assist States in implementing the requirements established in Safety Standards Series No. GS-R-1, Legal and Governmental Infrastructure for Nuclear, Radiation, Radioactive Waste and Transport Safety, for a national regulatory infrastructure to regulate any practice involving radiation sources in medicine, industry, research, agriculture and education. The Safety Guide provides advice on the legislative basis for establishing regulatory bodies, including the effective independence of the regulatory body. It also provides guidance on implementing the functions and activities of regulatory bodies: the development of regulations and guides on radiation safety; implementation of a system for notification and authorization; carrying out regulatory inspections; taking necessary enforcement actions; and investigating accidents and circumstances potentially giving rise to accidents. The various aspects relating to the regulatory control of consumer products are explained, including justification, optimization of exposure, safety assessment and authorization. Guidance is also provided on the organization and staffing of regulatory bodies. Contents: 1. Introduction; 2. Legal framework for a regulatory infrastructure; 3. Principal functions and activities of the regulatory body; 4. Regulatory control of the supply of consumer products; 5. Functions of the regulatory body shared with other governmental agencies; 6. Organization and staffing of the regulatory body; 7. Documentation of the functions and activities of the regulatory body; 8. Support services; 9. Quality management for the regulatory system.

Potential for nutrient recovery and biogas production from blackwater, food waste and greywater in urban source control systems.

Science.gov (United States)

Kjerstadius, H; Haghighatafshar, S; Davidsson, Å

2015-01-01

In the last decades, the focus on waste and wastewater treatment systems has shifted towards increased recovery of energy and nutrients. Separation of urban food waste (FW) and domestic wastewaters using source control systems could aid this increase; however, their effect on overall sustainability is unknown. To obtain indicators for sustainability assessments, five urban systems for collection, transport, treatment and nutrient recovery from blackwater, greywater and FW were investigated using data from implementations in Sweden or northern Europe. The systems were evaluated against their potential for biogas production and nutrient recovery by the use of mass balances for organic material, nutrients and metals over the system components. The resulting indicators are presented in units suitable for use in future sustainability studies or life-cycle assessment of urban waste and wastewater systems. The indicators show that source control systems have the potential to increase biogas production by more than 70% compared with a conventional system and give a high recovery of phosphorus and nitrogen as biofertilizer. The total potential increase in gross energy equivalence for source control systems was 20-100%; the greatest increase shown is for vacuum-based systems.

Balanced Current Control Strategy for Current Source Rectifier Stage of Indirect Matrix Converter under Unbalanced Grid Voltage Conditions

Directory of Open Access Journals (Sweden)

Yeongsu Bak

2016-12-01

Full Text Available This paper proposes a balanced current control strategy for the current source rectifier (CSR stage of an indirect matrix converter (IMC under unbalanced grid voltage conditions. If the three-phase grid connected to the voltage source inverter (VSI of the IMC has unbalanced voltage conditions, it affects the currents of the CSR stage and VSI stage, and the currents are distorted. Above all, the distorted currents of the CSR stage cause instability in the overall system, which can affect the life span of the system. Therefore, in this paper, a control strategy for balanced currents in the CSR stage is proposed. To achieve balanced currents in the CSR stage, the VSI stage should receive DC power without ripple components from the CSR stage. This is implemented by controlling the currents in the VSI stage. Therefore, the proposed control strategy decouples the positive and negative phase-sequence components existing in the unbalanced voltages and currents of the VSI stage. Using the proposed control strategy under unbalanced grid voltage conditions, the stability and life span of the overall system can be improved. The effectiveness of the proposed control strategy is verified by simulation and experimental results.

Source apportionment of sulfate and nitrate particulate matter in the Eastern United States and effectiveness of emission control programs.

Science.gov (United States)

Zhang, Hongliang; Hu, Jianlin; Kleeman, Michael; Ying, Qi

2014-08-15

Reducing population exposure to PM2.5 in the eastern US will require control of secondary sulfate and nitrate. A source-oriented Community Multi-scale Air Quality (CMAQ) model is used to determine contributions of major emission sources to nitrate and sulfate concentrations in the seven eastern US cities (New York City, Pittsburgh, Baltimore, Chicago, Detroit, St. Paul, and Winston-Salem) in January and August of 2000 and 2006. Identified major nitrate sources include on-road gasoline-powered vehicles, diesel engines, natural gas and coal combustion. From 2000 to 2006, January nitrate concentrations decreased by 25-68% for all the seven cities. On average, ~53% of this change was caused by emissions controls while 47% was caused by meteorology variations. August nitrate concentrations decreased by a maximum of 68% in New York City but Detroit experienced increasing August nitrate concentrations by up to 33%. On average, ~33% of the reduction in nitrate is offset by increases associated with meteorological conditions that favor nitrate formation. Coal combustion and natural gas are the dominant sources for sulfate in both seasons. January sulfate decrease from 2000 to 2006 in all cities by 4-58% except New York City, which increases by 13%. On average, ~93% of the reduction in sulfate was attributed to emission controls with 7% associated with changes in meteorology. August sulfate concentrations decrease by 11-44% in all cities. On average, emission controls alone between 2000 and 2006 would have caused 6% more reduction but the effectiveness of the controls was mitigated by meteorology conditions more favorable to sulfate production in 2006 vs. 2000. The results of this study suggest that regional emissions controls between 2000 and 2006 have been effective at reducing population exposure to PM2.5 in the eastern US, but yearly variations in meteorology must be carefully considered when assessing the exact magnitude of the control benefits. Copyright © 2014

Control system for RF-driven negative ion source experimental setup at HUST

Energy Technology Data Exchange (ETDEWEB)

Li, Dong; Wang, Xiaomin, E-mail: xm_wang@hust.edu.cn; Zhao, Peng; Liu, Kaifeng; Zhang, Lige; Yue, Haikun; Chen, Dezhi; Zuo, Chen

2017-03-15

Highlights: • The CompactRIO system is reliable and could achieve high-speed data collection. • The queue and event software structure allows the control code to be flexible. • TCP/IP performs better than shared variable method for mass data transmission. • The method for lowering the peak RF reflected power has been discussed and given. - Abstract: An experimental setup of RF-driven negative ion source has been built at the Huazhong University of Science and Technology (HUST). The control system for this setup is responsible for RF loading, gas feeding, filament heating, filament DC bias, data collection and Langmuir probe triggering during plasma production. To research influences on the plasma ignition of gas puff and RF power loading, the control system should be of flexible operating sequence, high-speed data collection and reliable data transmission. The general control unit (GCU) adopts a CompactRIO system, which performs high-speed data collection for gas pressure and RF power. The host control program adopts a queue and event structure for flexible operation, and TCP/IP method is applied for mass data transmission. The development of the host control program is described in detail. The test results of the shared variable and TCP/IP methods are presented, as well as data showing the advantages of the TCP/IP method. The experiment results with two different sequences of plasma production are given and discussed here.

Regulatory infrastructure for the control of radiation sources in the Africa region: Status, needs and programmes

International Nuclear Information System (INIS)

Skornik, K.

2001-01-01

In recent years, several African countries have taken steps towards creating or strengthening legal, administrative and technical mechanisms for the regulation and control of peaceful uses of nuclear technology, and towards improving the effectiveness and sustainability of radiation protection measures based on international standards. This stems from a growing awareness that a proper national infrastructure is a prerequisite for the implementation of safety standards to achieve and maintain the desired level of protection and safety, particularly in such sectors as public health and industry. Also, other issues of global and regional interest, such as the control of radiation sources, including the handling of hazardous waste, and response capabilities in the case of a radiological emergency, have contributed to a better perception of risks associated with deficiencies in or lack of adequate national radiation protection control mechanisms. Too often, however, this awareness has not been matched with adequate progress in the establishment of a regulatory framework for the control of radiation sources. This paper presents a summary of the current status of radiation protection infrastructure in all African Member States. On a background of still existing weaknesses and challenges, an overview of the Agency's response to assistance needs and programmes in this field is discussed. (author)

Tectonic control in source rock maturation and oil migration in Trinidad

Energy Technology Data Exchange (ETDEWEB)

Persad, K.M.; Talukdar, S.C.; Dow, W.G. (DGSI, The Woodlands, TX (United States))

1993-02-01

Oil accumulation in Trinidad were sourced by the Upper Cretaceous calcareous shales deposited along the Cretaceous passive margin of northern South America. Maturation of these source rocks, oil generation, migration and re-migration occurred in a foreland basin setting that resulted from interaction between Caribbean and South American plates during Late Oligocene to recent times. During Middle Miocene-Recent times, the foreland basin experienced strong compressional events, which controlled generation, migration, and accumulation of oil in Trinidad. A series of mature source rock kitchens formed in Late Miocene-Recent times in the Southern and Colombus Basins to the east-southeast of the Central Range Thrust. This thrust and associated fratured developed around 12 m.y.b.p. and served as vertical migration paths for the oil generated in Late Miocene time. This oil migrated into submarine fans deposited in the foreland basin axis and older reservoirs deformed into structural traps. Further generation and migration of oil, and re-migration of earlier oil took place during Pliocene-Holocene times, when later thrusting and wrench faulting served as vertical migration paths. Extremely high sedimentation rates in Pliocene-Pleistocene time, concurrent with active faulting, was responsible for very rapid generation of oil and gas. Vertically migrating gas often mixed with earlier migrated oil in overlying reservoirs. This caused depletion of oil in light hydrocarbons with accompanied fractionation among hydrocarbon types resulting in heavier oil in lower reservoirs, enrichment of light hydrocarbons and accumulation of gas-condensates in upper reservoirs. This process led to an oil-gravity stratification within about 10,000 ft of section.

Design of current controller of grid-connected voltage source converter based internal model control in wind power

Energy Technology Data Exchange (ETDEWEB)

Zhang Xianping; Guo Jindong; Xu Honghua [Inst. of Electrical Engineering, Chinese Academy of Sciences, BJ (China)

2008-07-01

Grid-connected voltage source converter (VSC) is important for variable speed turbines with doubly fed induction generator (DFIG), and bad performance of current loop of VSC may cause VSC inject much low and high order harmonics into grid. Therefore, design of current controller of VSC is very important. PI regulator is often used to regulate current error in dq rotating coordinate to obtain zero steady error. However, it is complex to design PI parameters, and researchers need many trial-and-error steps. Therefore, a novel and simple design method of PI regulator for grid-connected VSC, which is based internal model control (IMC), has been presented in this paper. The parameters of PI regulator can be expressed directly with certain L-type line filter parameters and the desired closed-loop bandwidth. At last, The simulation has been done and result shows that the method in this paper is easy and useful to regulate PI parameters. (orig.)

Spallation Neutron Source Accelerator Facility Target Safety and Non-safety Control Systems

International Nuclear Information System (INIS)

Battle, Ronald E.; DeVan, B.; Munro, John K. Jr.

2006-01-01

The Spallation Neutron Source (SNS) is a proton accelerator facility that generates neutrons for scientific researchers by spallation of neutrons from a mercury target. The SNS became operational on April 28, 2006, with first beam on target at approximately 200 W. The SNS accelerator, target, and conventional facilities controls are integrated by standardized hardware and software throughout the facility and were designed and fabricated to SNS conventions to ensure compatibility of systems with Experimental Physics Integrated Control System (EPICS). ControlLogix Programmable Logic Controllers (PLCs) interface to instruments and actuators, and EPICS performs the high-level integration of the PLCs such that all operator control can be accomplished from the Central Control room using EPICS graphical screens that pass process variables to and from the PLCs. Three active safety systems were designed to industry standards ISA S84.01 and IEEE 603 to meet the desired reliability for these safety systems. The safety systems protect facility workers and the environment from mercury vapor, mercury radiation, and proton beam radiation. The facility operators operated many of the systems prior to beam on target and developed the operating procedures. The safety and non-safety control systems were tested extensively prior to beam on target. This testing was crucial to identify wiring and software errors and failed components, the result of which was few problems during operation with beam on target. The SNS has continued beam on target since April to increase beam power, check out the scientific instruments, and continue testing the operation of facility subsystems

Imaging of Scattered Wavefields in Passive and Controlled-source Seismology

KAUST Repository

AlTheyab, Abdullah

2015-12-01

Seismic waves are used to study the Earth, exploit its hydrocarbon resources, and understand its hazards. Extracting information from seismic waves about the Earth’s subsurface, however, is becoming more challenging as our questions become more complex and our demands for higher resolution increase. This dissertation introduces two new methods that use scattered waves for improving the resolution of subsurface images: natural migration of passive seismic data and convergent full-waveform inversion. In the first part of this dissertation, I describe a method where the recorded seismic data are used to image subsurface heterogeneities like fault planes. This method, denoted as natural migration of backscattered surface waves, provides higher resolution images for near-surface faults that is complementary to surface-wave tomography images. Our proposed method differ from contemporary methods in that it does not (1) require a velocity model of the earth, (2) assumes weak scattering, or (3) have a high computational cost. This method is applied to ambient noise recorded by the US-Array to map regional faults across the American continent. Natural migration can be formulated as a least-squares inversion to furtherer enhance the resolution and the quality of the fault images. This inversion is applied to ambient noise recorded in Long Beach, California to reveal a matrix of shallow subsurface faults. The second part of this dissertation describes a convergent full waveform inversion method for controlled source data. A controlled source excites waves that scatter from subsurface reflectors. The scattered waves are recorded by a large array of geophones. These recorded waves can be inverted for a high-resolution image of the subsurface by FWI, which is typically convergent for transmitted arrivals but often does not converge for deep reflected events. I propose a preconditioning approach that extends the ability of FWI to image deep parts of the velocity model, which

Source attribution of human salmonellosis using a meta-analysis of case-control studies of sporadic infections

DEFF Research Database (Denmark)

Coutinho Calado Domingues, Ana Rita; Pires, Sara Monteiro; Hisham Beshara Halasa, Tariq

2012-01-01

Salmonella is an important cause of human illness. Disease is frequently associated with foodborne transmission, but other routes of exposure are recognized. Identifying sources of disease is essential for prioritizing public health interventions. Numerous case-control studies of sporadic salmone...

Alarm handler for the advanced photon source control system

International Nuclear Information System (INIS)

Kraimer, M.R.; Cha, B.K.; Anderson, M.

1991-01-01

The Advanced Photon Source (APS), now under construction at Argonne National Laboratory, will have a control system employing graphics workstations at the operator interface level and VME-based microprocessors operating with a distributed database at the field level. The alarm handler is an application utilizing X-Windows running on one or more operator interface workstations which monitors alarms generated by the VME-based microprocessors. Alarms can be grouped in a hierarchical manner. The operator can monitor, acknowledge, and mask alarms either individually or aggregately. Alarm changes of state and all operator modifications are logged. When alarms occur, display windows are automatically generated conveying system and subsystem relationships and severity. Menus are used to modify the alarm action configuration files and to obtain help. Since alarm groups are defined via an alarm configuration file, the alarm handler is a general purpose application which can be customized to monitor a single subsystem or configured to monitor the entire accelerator complex. 2 refs., 2 figs

pH control for enhanced reductive bioremediation of chlorinated solvent source zones

Energy Technology Data Exchange (ETDEWEB)

Robinson, Clare, E-mail: clare.robinson@epfl.ch [Laboratoire de technologie ecologique, Institut d' ingenierie de l' environnement, Station No. 2, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); Now at: Department of Civil and Environmental Engineering, University of Western Ontario, London, Canada N6A 5B9 (Canada); Barry, D.A., E-mail: andrew.barry@epfl.ch [Laboratoire de technologie ecologique, Institut d' ingenierie de l' environnement, Station No. 2, Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); McCarty, Perry L., E-mail: pmccarty@stanford.edu [Department of Civil and Environmental Engineering, Stanford University, Stanford, CA 94305-4020 (United States); Gerhard, Jason I., E-mail: j.gerhard@ed.ac.uk [Now at: Department of Civil and Environmental Engineering, University of Western Ontario, London, Canada N6A 5B9 (Canada); Institute for Infrastructure and Environment, University of Edinburgh, Edinburgh, EH9 3JL (United Kingdom); Kouznetsova, Irina, E-mail: irina.kouznetsova@ed.ac.uk [Institute for Infrastructure and Environment, University of Edinburgh, Edinburgh, EH9 3JL (United Kingdom)

2009-08-01

Enhanced reductive dehalogenation is an attractive treatment technology for in situ remediation of chlorinated solvent DNAPL source areas. Reductive dehalogenation is an acid-forming process with hydrochloric acid and also organic acids from fermentation of the electron donors typically building up in the source zone during remediation. This can lead to groundwater acidification thereby inhibiting the activity of dehalogenating microorganisms. Where the soils' natural buffering capacity is likely to be exceeded, the addition of an external source of alkalinity is needed to ensure sustained dehalogenation. To assist in the design of bioremediation systems, an abiotic geochemical model was developed to provide insight into the processes influencing the groundwater acidity as dehalogenation proceeds, and to predict the amount of bicarbonate required to maintain the pH at a suitable level for dehalogenating bacteria (i.e., > 6.5). The model accounts for the amount of chlorinated solvent degraded, site water chemistry, electron donor, alternative terminal electron-accepting processes, gas release and soil mineralogy. While calcite and iron oxides were shown to be the key minerals influencing the soil's buffering capacity, for the extensive dehalogenation likely to occur in a DNAPL source zone, significant bicarbonate addition may be necessary even in soils that are naturally well buffered. Results indicated that the bicarbonate requirement strongly depends on the electron donor used and availability of competing electron acceptors (e.g., sulfate, iron (III)). Based on understanding gained from this model, a simplified model was developed for calculating a preliminary design estimate of the bicarbonate addition required to control the pH for user-specified operating conditions.

Best Management Practices for sediment control in a Mediterranean agricultural watershed

Science.gov (United States)

Abdelwahab, Ossama M. M.; Bingner, Ronald L.; Milillo, Fabio; Gentile, Francesco

2015-04-01

Soil erosion can lead to severe destruction of agricultural sustainability that affects not only productivity, but the entire ecosystem in the neighboring areas. Sediments transported together with the associated nutrients and chemicals can significantly impact downstream water bodies. Various conservation and management practices implemented individually or integrated together as a system can be used to reduce the negative impacts on agricultural watersheds from soil erosion. Hydrological models are useful tools for decision makers when selecting the most effective combination of management practices to reduce pollutant loads within a watershed system. The Annualized Agricultural Non-point Source (AnnAGNPS) pollutant loading management model can be used to analyze the effectiveness of diverse management and conservation practices that can control or reduce the impact of soil erosion processes and subsequent sediment loads in agricultural watersheds. A 506 km2 Mediterranean medium-size watershed (Carapelle) located in Apulia, Southern Italy was used as a case study to evaluate the model and best management practices (BMPs) for sediment load control. A monitoring station located at the Ordona bridge has been instrumented to continuously monitor stream flow and suspended sediment loads. The station has been equipped with an ultrasound stage meter and a stage recorder to monitor stream flow. An infrared optic probe was used to measure suspended sediment concentrations (Gentile et al., 2010 ). The model was calibrated and validated in the Carapelle watershed on an event basis (Bisantino et al., 2013), and the validated model was used to evaluate the effectiveness of BMPs on sediment reduction. Various management practices were investigated including evaluating the impact on sediment load of: (1) converting all cropland areas into forest and grass covered conditions; (2) converting the highest eroding cropland areas to forest or grass covered conditions; and (3

Forestry BMP Implementation Costs for Virginia

Science.gov (United States)

R.M. Shaffer; H.L. Haney; E.G. Worrell; W.M. Aust

1998-01-01

Forestry Best Management Practices (BMPs) are operational techniques used to protect water quality during timber harvesting operations. The implementation cost of BMPs is important to loggers, forest landowners, and the forest industry. This study provides an estimate of BMP implementation cost on a per harvested acre basis for the coastal plain, Piedmont, and...

Power angle control of grid-connected voltage source converter in a wind energy application

Energy Technology Data Exchange (ETDEWEB)

Svensson, Jan [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Electric Power Engineering

1996-12-31

In this thesis, the connection of a voltage source converter to the grid in a wind energy application is examined. The possibility of using a cheap control system without grid current measurements, is investigated. The control method is based on controlling the voltage angle of the inverter, which governs the active power flow. The highest frequency of the power variation, coming from wind turbine, is approx. 5 Hz. Since the proposed control method easily can handle such power variations it is very well suited for wind turbine applications. The characteristics of the system depend on the DC-link capacitor, the grid filter inductance and resistance. Large values of the resistance damp the system well but increase the energy losses. A high inductance leads to a reduced harmonic level on the grid but makes the system slower. By using feed-forward of the generator/rectifier current signal, the performance is increased compared to an ordinary PI-control. Combining the Linear Quadratic (LQ) control method with Kalman filtered input signals, a robust control method with a good performance is obtained. The LQ controller controls both the phase displacement angle and the modulation index, resulting in higher bandwidth, and the typical power angle resonance at the grid frequency disappears. 22 refs, 109 figs, 14 tabs

Rate Control in Dual Source Evaporation

NARCIS (Netherlands)

Wielinga, T.; Gruisinga, W.; Leeuwis, H.; Lodder, J.C.; van Weers, J.F.; Wilmans, J.C.

1980-01-01

Two-component thin films are deposited in a high-vacuum system from two close sources, heated by an electron beam which is deflected between them. By using quartz-crystal monitors the evaporation rates are measured seperately, which is usually considered to be problematical. One rate signal is used

International conference on the safety and security of radioactive sources: Towards a global system for the continuous control of sources throughout their life cycle. Contributed papers

International Nuclear Information System (INIS)

2005-01-01

The objective of the conference is to promote a wide exchange of information on key issues relating to the safety and security of radioactive sources, including: drawing up an inventory; finding a solution without delay to situations resulting from past activities; preparing for the future by defining a global cooperative approach to the continuous control of radioactive sources during their life cycle. It is expected that the conference will foster a better understanding of the risks posed by these sources from the point of view of radiation safety and the threat associated with some of them in the event of malevolent use, and will help in finding ways of reducing the likelihood of the occurrence of a radiological incident or accident, or of a malevolent act. It is also expected to identify the preparedness and response measures that are necessary and to facilitate a common understanding on the feasibility of creating a sustainable global system for ensuring the safety and security of radioactive sources

International conference on the safety and security of radioactive sources: Towards a global system for the continuous control of sources throughout their life cycle. Contributed papers

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

The objective of the conference is to promote a wide exchange of information on key issues relating to the safety and security of radioactive sources, including: drawing up an inventory; finding a solution without delay to situations resulting from past activities; preparing for the future by defining a global cooperative approach to the continuous control of radioactive sources during their life cycle. It is expected that the conference will foster a better understanding of the risks posed by these sources from the point of view of radiation safety and the threat associated with some of them in the event of malevolent use, and will help in finding ways of reducing the likelihood of the occurrence of a radiological incident or accident, or of a malevolent act. It is also expected to identify the preparedness and response measures that are necessary and to facilitate a common understanding on the feasibility of creating a sustainable global system for ensuring the safety and security of radioactive sources.

Productivity of irrigated beans due to sources of stabilized nitrogen fertilizer and controlled release

Directory of Open Access Journals (Sweden)

Tatiely Gomes Bernardes

2015-12-01

Full Text Available ABSTRACT New nitrogen fertilizers are available in the market actually, however, does not have results on the efficiency of the Cerrado conditions. With that objective of this study was to evaluate the effect of urea including stabilized and controlled release urea on yield of irrigated common beans (Phaseolus vulgaris L in no-tillage system. The experiment was conducted in the winter crop, at Embrapa Arroz e Feijão, in Santo Antônio de Goiás, State of Goiás, Brazil. The experimental design was randomized blocks, with five replicates. Treatments consisted of five N sources (urea, urea + NBPT, urea + polymer, ammonium sulphate, and ammonium nitrate and a control (without N being applied 20 kg ha-1 of N at sowing and 80 kg ha-1 onf N in topdressing. We evaluated the chlorophyll content in leaves of common beans, the leaf N content and dry mass weight (MSPA in the flowering of common beans, the number of pods per plant, number of grains per pod, mass of 100 grains, grain yield and final stand of the common beans. The sources of nitrogen fertilizer did not influence, leaf N content, the mass of MSPA and the relative chlorophyll index of common beans. The use of polymerized urea and urea with urease inhibitor, did not produce increases in the number of grains per pod, number of pods per plant, mass of 100 grains and common beans yield compared to traditional sources of N, urea, ammonium sulfate and ammonium nitrate.

Assessment of Runoff and Sediment Yields Using the AnnAGNPS Model in a Three-Gorge Watershed of China

Directory of Open Access Journals (Sweden)

Hongwei Nan

2012-05-01

Full Text Available Soil erosion has been recognized as one of the major threats to our environment and water quality worldwide, especially in China. To mitigate nonpoint source water quality problems caused by soil erosion, best management practices (BMPs and/or conservation programs have been adopted. Watershed models, such as the Annualized Agricultural Non-Point Source Pollutant Loading model (AnnAGNPS, have been developed to aid in the evaluation of watershed response to watershed management practices. The model has been applied worldwide and proven to be a very effective tool in identifying the critical areas which had serious erosion, and in aiding in decision-making processes for adopting BMPs and/or conservation programs so that cost/benefit can be maximized and non-point source pollution control can be achieved in the most efficient way. The main goal of this study was to assess the characteristics of soil erosion, sediment and sediment delivery of a watershed so that effective conservation measures can be implemented. To achieve the overall objective of this study, all necessary data for the 4,184 km² Daning River watershed in the Three-Gorge region of the Yangtze River of China were assembled. The model was calibrated using observed monthly runoff from 1998 to 1999 (Nash-Sutcliffe coefficient of efficiency of 0.94 and R² of 0.94 and validated using the observed monthly runoff from 2003 to 2005 (Nash-Sutcliffe coefficient of efficiency of 0.93 and R² of 0.93. Additionally, the model was validated using annual average sediment of 2000–2002 (relative error of −0.34 and 2003–2004 (relative error of 0.18 at Wuxi station. Post validation simulation showed that approximately 48% of the watershed was under the soil loss tolerance released by the Ministry of Water Resources of China (500 t·km⁻²·y⁻¹. However, 8% of the watershed had soil erosion of exceeding 5,000 t·km⁻²

Energy Management of Dual-Source Propelled Electric Vehicle using Fuzzy Controller Optimized via Genetic Algorithm

DEFF Research Database (Denmark)

Khoobi, Saeed; Halvaei, Abolfazl; Hajizadeh, Amin

2016-01-01

Energy and power distribution between multiple energy sources of electric vehicles (EVs) is the main challenge to achieve optimum performance from EV. Fuzzy inference systems are powerful tools due to nonlinearity and uncertainties of EV system. Design of fuzzy controllers for energy management...... of EV relies too much on the expert experience and it may lead to sub-optimal performance. This paper develops an optimized fuzzy controller using genetic algorithm (GA) for an electric vehicle equipped with two power bank including battery and super-capacitor. The model of EV and optimized fuzzy...

The Biopsychology-Toolbox: a free, open-source Matlab-toolbox for the control of behavioral experiments.

Science.gov (United States)

Rose, Jonas; Otto, Tobias; Dittrich, Lars

2008-10-30

The Biopsychology-Toolbox is a free, open-source Matlab-toolbox for the control of behavioral experiments. The major aim of the project was to provide a set of basic tools that allow programming novices to control basic hardware used for behavioral experimentation without limiting the power and flexibility of the underlying programming language. The modular design of the toolbox allows portation of parts as well as entire paradigms between different types of hardware. In addition to the toolbox, this project offers a platform for the exchange of functions, hardware solutions and complete behavioral paradigms.

Control strategy and experimental study on a novel defrosting method for air-source heat pump

International Nuclear Information System (INIS)

Liang Caihua; Zhang Xiaosong; Li Xiuwei; Chen Zhenqian

2010-01-01

A new defrosting method - the sensible heat defrosting method, aiming at shelving the various disadvantages of the conventional reverse cycle defrosting was proposed in this paper. The mechanism and process of this method was analysed. To guarantee the reliability, the self-organizing control algorithm with self-learning function was introduced based on the cardinal fuzzy control algorithm. Moreover, the control strategy was enacted; the corresponding self-organizing fuzzy control system was developed; the Micro Controller Unit (MCU) based control unit was accomplished; and the experimental study was conducted to investigate the sample machine of air-source heat pump system. The results of the experiments showed that the self-organizing control algorithm has good control characteristic and effect. On one hand, the adverse shock from the conventional reverse cycle defrosting to the refrigeration system could be avoided through this proposed method; on the other hand, the 'oil rush' could also be eliminated. Besides, the thermal comfort could be greatly improved since the temperature fluctuation range of the supplied water is narrowed by applying this new method in practice.

New approach for location of continuously emitting acoustic emission sources by phase-controlled probe arrays

International Nuclear Information System (INIS)

Hoeller, P.; Klein, M.; Waschkies, E.; Deuster, G.

1991-01-01

Usually burst-like acoustic emission (AE) is localized by triangulation. For continuous AE, e.g. from leakages, this method is not feasible. Therefore a new method for localization of continuous AE has been developed. It is based on a phase-controlled probe array which consists of many single sensor elements. The AE signals received by the different sensor elements are delayed according to their time-of-flight differences from the source to the single elements of the receiver array. By choosing special combinations of time differences between the array elements the directivity pattern of the sensitivity of the array can be changed, e.g. rotated in the plane of a large plate. Thus, the source direction can be determined by one array. Some preliminary experiments with an artificial noise source, positioned on a large steel plate, have been performed and have demonstrated the feasibility of this approach. (orig.)

Understanding perceptions of stakeholder groups about Forestry Best Management Practices in Georgia.

Science.gov (United States)

Tumpach, Chantal; Dwivedi, Puneet; Izlar, Robert; Cook, Chase

2018-05-01

Forestry Best Management Practices (BMPs) are critical in ensuring sustainable forest management in the United States because of their effectiveness in protecting water quality, reducing soil erosion, maintaining riparian habitat, and sustaining site productivity. The success of forestry BMPs depends heavily on coordination among primary stakeholder groups. It is important to understand perceptions of such groups for a successful forest policy formulation. We used the SWOT-AHP (Strengths, Weaknesses, Opportunities, and Threats analysis with the Analytical Hierarchy Process) framework to assess perceptions of three stakeholder groups (loggers, landowners, agency foresters) about forestry BMPs in Georgia, the largest roundwood producing state in the United States. The agency and logger stakeholder groups gave the highest priority to improved reputation under the strength category, whereas the landowner stakeholder group perceived sustainable forestry as the highest priority under the same category. Lack of landowner education was the highest priority under the weakness category for landowner and agency stakeholder groups, whereas the logger stakeholder group selected lack of trained personnel as the highest priority under the same category. Agency and landowner stakeholder groups gave the highest priority to training and education while loggers indicated maintenance of forest-based environmental benefits as their highest priority under the opportunity category. Finally, landowners and agency stakeholder groups perceived more regulations and restrictions as most significant in the threat category whereas the logger stakeholder group was most concerned about the insufficient accounting of cost sharing under the same category. Overall, selected stakeholder groups recognize the importance of forestry BMPs and had positive perceptions about them. A collaborative approach based on continuous feedback can streamline expectations of stakeholder groups about forestry BMPs in

Controllable quantum private queries using an entangled Fibonacci-sequence spiral source

Energy Technology Data Exchange (ETDEWEB)

Lai, Hong, E-mail: honglaimm@163.com [School of Computer and Information Science, Southwest University, Chongqing 400715 (China); Department of Computing, Macquarie University, Sydney, NSW 2109 (Australia); School of Science, Beijing University of Posts and Telecommunications, Beijing 100876 (China); Orgun, Mehmet A. [Department of Computing, Macquarie University, Sydney, NSW 2109 (Australia); Pieprzyk, Josef [School of Electrical Engineering and Computer Science, Queensland University of Technology, Brisbane, QLD 4000 (Australia); Xiao, Jinghua [School of Science, Beijing University of Posts and Telecommunications, Beijing 100876 (China); Xue, Liyin [Corporate Analytics, The Australian Taxation Office, Sydney NSW 2000 (Australia); Jia, Zhongtian, E-mail: ise_jiazt@ujn.edu.cn [Provincial Key Laboratory for Network Based Intelligent Computing, University of Jinan, Jinan 250022 (China)

2015-10-23

Highlights: • Alice can easily control the size of a block by adjusting the parameter m rather than a high-dimension oracle. • The case of Alice knowing an exact multi-bit message can be realized deterministically. • Our protocol provides broad measures of protection against errors caused by the effect of noise. • Our protocol can greatly save both quantum and classical communication and exhibit some advantages in security. • Our protocol is scalable and flexible, and secure against quantum memory attacks by Alice. - Abstract: By changing the initial values in entangled Fibonacci-sequence spiral sources in Simon et al.'s (2013) experimental setup [13], we propose a controllable quantum private query protocol. Moreover, our protocol achieves flexible key expansion and even exhibits secure advantages during communications because of the following observations. We observe the close relationships between Lucas numbers and the first kind of Chebyshev maps, and the Chebyshev maps and k-Chebyshev maps; by adjusting the parameter m in k-Chebyshev maps, Alice and Bob can obtain their expected values of the key blocks and database respectively.

Controllable quantum private queries using an entangled Fibonacci-sequence spiral source

International Nuclear Information System (INIS)

Lai, Hong; Orgun, Mehmet A.; Pieprzyk, Josef; Xiao, Jinghua; Xue, Liyin; Jia, Zhongtian

2015-01-01

Highlights: • Alice can easily control the size of a block by adjusting the parameter m rather than a high-dimension oracle. • The case of Alice knowing an exact multi-bit message can be realized deterministically. • Our protocol provides broad measures of protection against errors caused by the effect of noise. • Our protocol can greatly save both quantum and classical communication and exhibit some advantages in security. • Our protocol is scalable and flexible, and secure against quantum memory attacks by Alice. - Abstract: By changing the initial values in entangled Fibonacci-sequence spiral sources in Simon et al.'s (2013) experimental setup [13], we propose a controllable quantum private query protocol. Moreover, our protocol achieves flexible key expansion and even exhibits secure advantages during communications because of the following observations. We observe the close relationships between Lucas numbers and the first kind of Chebyshev maps, and the Chebyshev maps and k-Chebyshev maps; by adjusting the parameter m in k-Chebyshev maps, Alice and Bob can obtain their expected values of the key blocks and database respectively

Efficiencies of forestry best management practices for reducing sediment and nutrient losses in the eastern United States

Science.gov (United States)

Pamela Edwards; Karl W.J. Williard

2010-01-01

Quantifying the effects of forestry best management practices (BMPs) on sediment and nutrient loads is a critical need. Through an exhaustive literature search, three paired forested watershed studies in the eastern United States were found that permitted the calculation of BMP efficiencies--the percent reduction in sediment or nutrients achieved by BMPs. For sediment...

Micro-controller based fiber optic data telemetry system for the ion source of low energy accelerator facility at BARC

International Nuclear Information System (INIS)

Padmakumar, Sapna; Ware, Shailaja V.; Subrahmanyam, N.B.V.; Bhatt, J.P.; Singh, S.K.; Gupta, S.K.; Singh, P.; Choudhury, R.K.

2009-01-01

The Low Energy Accelerator Facility (LEAF) is a 50 keV, high intensity, negative ion accelerator facility that has been set up indigenously at Nuclear Physics Division, BARC. This facility is capable of delivering a wide range of negative ion beams of both light and heavy ions across the periodic table using a SNICS II (Source of Negative Ion by Caesium Sputtering) source. A micro-controller based control and monitoring system has been developed exclusively for the ion source parameters of LEAF. The data control and monitoring system mainly targets acquiring the data from the field in the terms of parameters such as voltages and currents. There are processes which need to be monitored continuously in order to keep certain parameters under check. The microcontroller based fiber optic data telemetry system allows us to perform the aforesaid task. The voltages can be controlled and monitored by providing the inputs and receiving the feedback through a user friendly graphic user interface. With this system one can control the status as well as analog value of the high voltage power supplies like extractor, cathode, filament, focus line heater and oven. This system consists of Fiber optic transceiver, which is connected on serial port (RS 232C) of microcontroller as well as RS232 port of PC. The whole control system is reliable even in noisy environments including RF and worse EMI conditions. This compact modular design is implemented using low cost devices and allows easy and fast maintainability. In the paper, the details of the system are presented. (author)

Automation system for quality control in manufacture of iodine-125 sealed sources used in brachytherapy

International Nuclear Information System (INIS)

Somessari, Samir L.; Feher, Anselmo; Sprenger, Francisco E.; Rostellato, Maria E.C.M.; Moura, Joao A.; Costa, Osvaldo L.; Calvo, Wilson A.P.

2011-01-01

The objective of this work is to develop an automation system for Quality Control in the production of Iodine-125 sealed sources, after undergoing the process of laser beam welding. These sources, also known as Iodine-125 seeds are used, successfully, in the treatment of cancer by brachytherapy, with low-dose rates. Each small seed is composed of a welded titanium capsule with 0.8 mm diameter and 4.5 mm in length, containing Iodine-125 adsorbed on an internal silver wire. The seeds are implanted in the human prostate to irradiate the tumor and treat the cancerous cells. The technology to automate the quality control system in the manufacture of Iodine-125 seeds consists in developing and associate mechanical parts, electronic components and pneumatic circuits to control machines and processes. The automation technology for Iodine-125 seed production developed in this work employs programmable logic controller, step motors, drivers of control, electrical-electronic interfaces, photoelectric sensors, interfaces of communication and software development. Industrial automation plays an important role in the production of Iodine-125 seeds, with higher productivity and high standard of quality, facilitating the implementation and operation of processes with good manufacturing practices. Nowadays, the Radiation Technology Center at IPEN-CNEN/SP imports and distributes 36,000 Iodine-125 seeds per year for clinics and hospitals in the whole country. However, the Brazilian potential market is of 8,000 Iodine-125 seeds per month. Therefore, the local production of these radioactive seeds has become a priority for the Institute, aiming to reduce the price and increase the supply to the population in Brazil. (author)

Automation system for quality control in manufacture of iodine-125 sealed sources used in brachytherapy

Energy Technology Data Exchange (ETDEWEB)

Somessari, Samir L.; Feher, Anselmo; Sprenger, Francisco E.; Rostellato, Maria E.C.M.; Moura, Joao A.; Costa, Osvaldo L.; Calvo, Wilson A.P., E-mail: somessar@ipen.b, E-mail: afeher@ipen.b, E-mail: sprenger@ipen.b, E-mail: elisaros@ipen.b, E-mail: olcosta@ipen.b, E-mail: wapcalvo@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

The objective of this work is to develop an automation system for Quality Control in the production of Iodine-125 sealed sources, after undergoing the process of laser beam welding. These sources, also known as Iodine-125 seeds are used, successfully, in the treatment of cancer by brachytherapy, with low-dose rates. Each small seed is composed of a welded titanium capsule with 0.8 mm diameter and 4.5 mm in length, containing Iodine-125 adsorbed on an internal silver wire. The seeds are implanted in the human prostate to irradiate the tumor and treat the cancerous cells. The technology to automate the quality control system in the manufacture of Iodine-125 seeds consists in developing and associate mechanical parts, electronic components and pneumatic circuits to control machines and processes. The automation technology for Iodine-125 seed production developed in this work employs programmable logic controller, step motors, drivers of control, electrical-electronic interfaces, photoelectric sensors, interfaces of communication and software development. Industrial automation plays an important role in the production of Iodine-125 seeds, with higher productivity and high standard of quality, facilitating the implementation and operation of processes with good manufacturing practices. Nowadays, the Radiation Technology Center at IPEN-CNEN/SP imports and distributes 36,000 Iodine-125 seeds per year for clinics and hospitals in the whole country. However, the Brazilian potential market is of 8,000 Iodine-125 seeds per month. Therefore, the local production of these radioactive seeds has become a priority for the Institute, aiming to reduce the price and increase the supply to the population in Brazil. (author)

Fuel fired heat sources

Energy Technology Data Exchange (ETDEWEB)

Ortlinghaus, U

1977-09-08

Fuel fired heat sources with a valve-controlled ignition and main burner, whose flame is monitored and whose control valve is closed or opened by a controller according to the control deviation between actual and reference heat source temperature, previously suffered the disadvantage of high consumption of ignition gas. According to the invention this disadvantage is avoided by closing the ignition valve from the controller via a delay unit and having the delay time of the delay unit controlled either by the temperature measured by the sensor or increasing it with increasing deviation of the actual value of pre-temperature from the reference value of the pre-temperature.

Redatuming controlled-source electromagnetic data using Stratton–Chu type integral transformations

DEFF Research Database (Denmark)

Zhdanov, Michael; Cai, Hongzhu

2016-01-01

We present a new method of analyzing controlled-source electromagnetic (CSEM) data based on redatuming of the observed data from the actual receivers into the virtual receivers. We use the Stratton–Chu type integral transform to calculate the EM field in the virtual receivers. The virtual receivers...... can be placed at any desirable position, including close to the target, which increases the sensitivity of the EM data to the target. The developed method provides an effective model-based interpolation/extrapolation tool for electromagnetic field data. This paper demonstrates that redatuming can...... be used for designing the optimized CSEM survey configuration. The numerical examples, for the Kevin Dome Electromagnetic Project Site, illustrate the practical effectiveness of the developed method....

Dynamics of BMP signaling in limb bud mesenchyme and polydactyly.

Science.gov (United States)

Norrie, Jacqueline L; Lewandowski, Jordan P; Bouldin, Cortney M; Amarnath, Smita; Li, Qiang; Vokes, Martha S; Ehrlich, Lauren I R; Harfe, Brian D; Vokes, Steven A

2014-09-15

Mutations in the Bone Morphogenetic Protein (BMP) pathway are associated with a range of defects in skeletal formation. Genetic analysis of BMP signaling requirements is complicated by the presence of three partially redundant BMPs that are required for multiple stages of limb development. We generated an inducible allele of a BMP inhibitor, Gremlin, which reduces BMP signaling. We show that BMPs act in a dose and time dependent manner in which early reduction of BMPs result in digit loss, while inhibiting overall BMP signaling between E10.5 and E11.5 allows polydactylous digit formation. During this period, inhibiting BMPs extends the duration of FGF signaling. Sox9 is initially expressed in normal digit ray domains but at reduced levels that correlate with the reduction in BMP signaling. The persistence of elevated FGF signaling likely promotes cell proliferation and survival, inhibiting the activation of Sox9 and secondarily, inhibiting the differentiation of Sox9-expressing chondrocytes. Our results provide new insights into the timing and clarify the mechanisms underlying BMP signaling during digit morphogenesis. Copyright © 2014 Elsevier Inc. All rights reserved.

SOURCE CHARACTERIZATION AND CONTROL TECHNOLOGY ASSESSMENT OF METHYLENE CHLORIDE EMISSIONS FROM EASTMAN KODAK COMPANY, ROCHESTER, NY

Science.gov (United States)

The report gives results of an assessment of potential control technologies for methylene chloride (also known as dichloromethane or DCM) emission sources at Eastman Kodak Company's Kodak Park facility in Rochester, NY. DCM is a solvent used by Kodak in the manufacture of cellulo...

Conjoint Analysis of Farmers’ Response to Conservation Incentives

Directory of Open Access Journals (Sweden)

David Conner

2016-07-01

Full Text Available Environmental degradation threatens the long term resiliency of the US food and farming system. While USDA has provided conservation incentives for the adoption of best management practices (BMPs, only a small percentage of farms have participated in such conservation programs. This study uses conjoint analysis to examine Vermont farmers’ underlying preferences and willingness-to-accept (WTA incentives for three common BMPs. Based on the results of this survey, we hypothesize that federal cost share programs’ payments are below preferred incentive levels and that less familiar and more complex BMPs require a higher payment. Our implications focus on strategies to test these hypotheses and align incentive payments and other non-monetary options to increase BMP adoption.

Regulatory control for safe usage of radiation sources in India

International Nuclear Information System (INIS)

Ghosh, P.K.; Sonawane, A.U.

1998-01-01

The widespread applications of radioactive materials and radiation generating equipment in the field of industry, medicine agriculture and research in India necessitated the establishment of an efficient regulatory framework and consequently the Atomic Energy Regulatory Board (AERB) was constituted to exercise regulatory control over the safe usage of the radioactive materials and the radiation generating equipment. The Atomic Energy Act, 1962 and the Radiation Protection Rules, 1971 promulgated under the Act forms the basis of radiation safety in India and Chairman, AERB is the Competent Authority to enforce the regulatory provisions of the Radiation Protection Rules, 1971, for safe use of radiation source in the country. AERB has published a number of documents such as Radiation Surveillance Procedures, Standards, Codes, Guides and Manuals for safe use and handling of radioactive materials and radiation generating equipment. Apart from nuclear fuel cycle documents, these publications pertain to industrial radiography, medical application of radiation, transport of radioactive material, industrial gamma irradiators, X-ray units etc. AERB safety related publications are based on international standards e.g. BSS, IAEA, ICRP, ISO etc. This paper outlines the methodology of regulatory control exercised by AERB for safe use of the radioactive materials and the radiation generating equipment in the country. (author)

Sole-Source Lighting for Controlled-Environment Agriculture

Science.gov (United States)

Mitchell.Cary; Stutte, Gary W.

2015-01-01

Since plants on Earth evolved under broad-spectrum solar radiation, anytime they are grown exclusively under electric lighting that does not contain all wavelengths in similar proportion to those in sunlight, plant appearance and size could be uniquely different. Nevertheless, plants have been grown for decades under fluorescent (FL) (1) + incandescent (IN) (2) lamps as a sole source of lighting (SSL), and researchers have become comfortable that, in certain proportions of FL + IN for a given species, plants can appear "normal" relative to their growth outdoors. The problem with using such traditional SSLs for commercial production typically is short lamp lifespans and not obtaining enough photosynthetically active radiation (PAR, 400-700 nm) when desired. These limitations led to supplementation of FL + IN lamp outputs with longer-lived, high-intensity discharge (HID) lamps in growth chambers (3). As researchers became comfortable that mixes of orange-biased high-pressure sodium (HPS) and blue-biased metal halide (MH) HIDs together also could give normal plant growth at higher intensities, growth chambers and phytotrons subsequently were equipped mainly with HID lamps, with their intense thermal output filtered out by ventilated light caps or thermal-controlled water barriers. For the most part, IN and HID lamps have found a home in commercial protected horticulture, usually for night-break photoperiod lighting (IN) or for seasonal supplemental lighting (mostly HPS) in greenhouses. However, lack of economically viable options for SSL have held back aspects of year-round indoor agriculture from taking off commercially.

BEAMLINE-CONTROLLED STEERING OF SOURCE-POINT ANGLE AT THE ADVANCED PHOTON SOURCE

Energy Technology Data Exchange (ETDEWEB)

Emery, L.; Fystro, G.; Shang, H.; Smith, M.

2017-06-25

An EPICS-based steering software system has been implemented for beamline personnel to directly steer the angle of the synchrotron radiation sources at the Advanced Photon Source. A script running on a workstation monitors "start steering" beamline EPICS records, and effects a steering given by the value of the "angle request" EPICS record. The new system makes the steering process much faster than before, although the older steering protocols can still be used. The robustness features of the original steering remain. Feedback messages are provided to the beamlines and the accelerator operators. Underpinning this new steering protocol is the recent refinement of the global orbit feedback process whereby feedforward of dipole corrector set points and orbit set points are used to create a local steering bump in a rapid and seamless way.

First results from experiment in South China Sea using marine controlled source electromagnetic

Science.gov (United States)

Li, Yuan; Wang, Lipeng; Deng, Ming

2016-04-01

We concentrated on the use of marine controlled-source electromagnetic (CSEM) sounding with a horizontal electric dipole source towed close to the seafloor and receivers anchored on the seafloor. We applied the CSEM method in South China Sea for the first time in 2014, which not only test the application of our instrument, but also test our data processing method. Electromagnetic fields transmitted by a towed electric dipole source in deep sea were measured by a linear array of six seafloor receivers, positioned 600 meter (m) apart. Our results provided two highly resistivity layers beneath the survey line and the gas hydrate saturation profile associated with the anomalous resistivity. In the letter, we discussed some anomalous layers during the interpretation steps. The most plausible explanation of the first resistivity layer anomalies is that large amounts of gas hydrate have accumulated at 200 m depth below the seep sites, and the second layers is considerable volumes of gas hydrate have accumulated the seafloor at survey line according to the conceptual model, during the resistivity compared with other evidence like seismic and well data from the same survey. We should try other observation like heat flow, geochemical or other evidence to test the statement in the future.

A Current Control Approach for an Abnormal Grid Supplied Ultra Sparse Z-Source Matrix Converter with a Particle Swarm Optimization Proportional-Integral Induction Motor Drive Controller

Directory of Open Access Journals (Sweden)

Seyed Sina Sebtahmadi

2016-11-01