Sediment sources in a small agricultural catchment: A composite fingerprinting approach based on the selection of potential sources

Science.gov (United States)

Zhou, Huiping; Chang, Weina; Zhang, Longjiang

2016-08-01

Fingerprinting techniques have been widely used as a reasonable and reliable means for investigating sediment sources, especially in relatively large catchments in which there are significant differences in surface materials. However, the discrimination power of fingerprint properties for small catchments, in which the surface materials are relatively homogeneous and human interference is marked, may be affected by fragmentary or confused source information. Using fingerprinting techniques can be difficult, and there is still a need for further studies to verify the effectiveness of such techniques in these small catchments. A composite fingerprinting approach was used in this study to investigate the main sources of sediment output, as well as their relative contributions, from a small catchment (30 km2) with high levels of farming and mining activities. The impact of the selection of different potential sediment sources on the derivation of composite fingerprints and its discrimination power were also investigated by comparing the results from different combinations of potential source types. The initial source types and several samples that could cause confusion were adjusted. These adjustments improved the discrimination power of the composite fingerprints. The results showed that the composite fingerprinting approach used in this study had a discriminatory efficiency of 89.2% for different sediment sources and that the model had a mean goodness of fit of 0.90. Cultivated lands were the main sediment source. The sediment contribution of the studied cultivated lands ranged from 39.9% to 87.8%, with a mean of 76.6%, for multiple deposited sediment samples. The mean contribution of woodlands was 21.7%. Overall, the sediment contribution from mining and road areas was relatively low. The selection of potential sources is an important factor in the application of fingerprinting techniques and warrants more attention in future studies, as is the case with other

Solid recovered fuel: influence of waste stream composition and processing on chlorine content and fuel quality.

Science.gov (United States)

Velis, Costas; Wagland, Stuart; Longhurst, Phil; Robson, Bryce; Sinfield, Keith; Wise, Stephen; Pollard, Simon

2012-02-07

Solid recovered fuel (SRF) produced by mechanical-biological treatment (MBT) of municipal waste can replace fossil fuels, being a CO(2)-neutral, affordable, and alternative energy source. SRF application is limited by low confidence in quality. We present results for key SRF properties centered on the issue of chlorine content. A detailed investigation involved sampling, statistical analysis, reconstruction of composition, and modeling of SRF properties. The total chlorine median for a typical plant during summer operation was 0.69% w/w(d), with lower/upper 95% confidence intervals of 0.60% w/w(d) and 0.74% w/w(d) (class 3 of CEN Cl indicator). The average total chlorine can be simulated, using a reconciled SRF composition before shredding to limit for ash content marginally below the 20% w/w(d) deemed suitable for certain power plants; and a lower 95% confidence limit of net calorific value (NCV) at 14.5 MJ kg(ar)(-1). The data provide, for the first time, a high level of confidence on the effects of SRF composition on its chlorine content, illustrating interrelationships with other fuel properties. The findings presented here allow rational debate on achievable vs desirable MBT-derived SRF quality, informing the development of realistic SRF quality specifications, through modeling exercises, needed for effective thermal recovery.

Funding source and research report quality in nutrition practice-related research.

Directory of Open Access Journals (Sweden)

Esther F Myers

Full Text Available BACKGROUND: The source of funding is one of many possible causes of bias in scientific research. One method of detecting potential for bias is to evaluate the quality of research reports. Research exploring the relationship between funding source and nutrition-related research report quality is limited and in other disciplines the findings are mixed. OBJECTIVE: The purpose of this study is to determine whether types of funding sources of nutrition research are associated with differences in research report quality. DESIGN: A retrospective study of research reporting quality, research design and funding source was conducted on 2539 peer reviewed research articles from the American Dietetic Association's Evidence Analysis Library® database. RESULTS: Quality rating frequency distributions indicate 43.3% of research reports were rated as positive, 50.1% neutral, and 6.6% as negative. Multinomial logistic regression results showed that while both funding source and type of research design are significant predictors of quality ratings (χ2 = 118.99, p≤0.001, the model's usefulness in predicting overall research report quality is little better than chance. Compared to research reports with government funding, those not acknowledging any funding sources, followed by studies with University/hospital funding were more likely to receive neutral vs positive quality ratings, OR = 1.85, P <0.001 and OR = 1.54, P<0.001, respectively and those that did not report funding were more likely to receive negative quality ratings (OR = 4.97, P<0.001. After controlling for research design, industry funded research reports were no more likely to receive a neutral or negative quality rating than those funded by government sources. CONCLUSION: Research report quality cannot be accurately predicted from the funding source after controlling for research design. Continued vigilance to evaluate the quality of all research regardless of the funding source

Development of quality assurance procedures for production of sealed radiation source

CERN Document Server

Nam, J H; Cho, W K; Han, H S; Hong, S B; Kim, K H; Kim, S D; Lee, Y G; Lim, N J

2001-01-01

The quality assurance procedures for sealed radiation sources production using HANARO and RIPF have been developed. The detailed quality assurance procedures are essential to manage the whole work process effectively and ensure the quality of the produced sealed sources. Through applying this quality assurance procedures to the entire production works of the sealed radiation sources, it is expected that the quality of the products, the safety of the works and the satisfaction of the customers will be increased.

Scintillation screen applications in a vacuum arc ion source with composite hydride cathode

Science.gov (United States)

Wang, X. H.; Tuo, X. G.; Yang, Z.; Peng, Y. F.; Li, J.; Lv, H. Y.; Li, J. H.; Long, J. D.

2018-05-01

Vacuum arc ion source with composite hydride cathode was developed to produce intense ion beams which can be applied in particle accelerator injections. Beam profile and beam composition are two fundamental parameters of the beam for the vacuum arc ion source in such specific applications. An aluminum-coated scintillation screen with an ICCD camera readout was used to show the space-time distribution of the beam directly. A simple magnetic analysis assembly with the scintillation screen shows the beam composition information of this kind ion source. Some physical and technical issues are discussed and analyzed in the text.

Wintertime aerosol chemical composition and source apportionment of the organic fraction in the metropolitan area of Paris

Directory of Open Access Journals (Sweden)

M. Crippa

2013-01-01

Full Text Available The effect of a post-industrial megacity on local and regional air quality was assessed via a month-long field measurement campaign in the Paris metropolitan area during winter 2010. Here we present source apportionment results from three aerosol mass spectrometers and two aethalometers deployed at three measurement stations within the Paris region. Submicron aerosol composition is dominated by the organic fraction (30–36% and nitrate (28–29%, with lower contributions from sulfate (14–16%, ammonium (12–14% and black carbon (7–13%.

Organic source apportionment was performed using positive matrix factorization, resulting in a set of organic factors corresponding both to primary emission sources and secondary production. The dominant primary sources are traffic (11–15% of organic mass, biomass burning (13–15% and cooking (up to 35% during meal hours. Secondary organic aerosol contributes more than 50% to the total organic mass and includes a highly oxidized factor from indeterminate and/or diverse sources and a less oxidized factor related to wood burning emissions. Black carbon was apportioned to traffic and wood burning sources using a model based on wavelength-dependent light absorption of these two combustion sources. The time series of organic and black carbon factors from related sources were strongly correlated. The similarities in aerosol composition, total mass and temporal variation between the three sites suggest that particulate pollution in Paris is dominated by regional factors, and that the emissions from Paris itself have a relatively low impact on its surroundings.

The link between composition and balance in masterworks vs. paintings of lower artistic quality.

Science.gov (United States)

Vartanian, Oshin; Martindale, Colin; Podsiadlo, Jacob; Overbay, Shane; Borkum, Jonathan

2005-11-01

In painting, composition is commonly defined as the two-dimensional arrangement of elements within the canvas. Each element is considered to have a perceptual weight. The arrangement of these weighted elements determines how balanced a painting is. It has been suggested that due to superior composition, masterworks may be more balanced than works of lower artistic quality. We tested this hypothesis by instructing our participants to rate masterworks and selections of lower artistic quality on balance. This hypothesis was not supported. Second, it has been suggested that rearranging elements within a painting may have a more detrimental effect on composition (and by extension balance) in masterworks than in selections of lower artistic quality. This view associates works of higher artistic quality with visual rightness, thereby predicting that compositional change would be more likely to cause deviations from a visually right state in masterworks. We tested this hypothesis by displacing an element within each painting to a different location, and measuring the effect on balance. In accordance with recent findings in the literature, we also took into account the severity of the compositional alterations. The results demonstrated that compositional alteration affected balance ratings equally across masterworks and selections of lower artistic quality. These results demonstrate that, although balance is a function of compositional structure, balance on its own is not sufficient to distinguish between works of varying artistic quality. To the extent that balance is considered a function of composition, the results suggest that masterworks are distinguished from works of lower artistic quality for reasons other than solely composition.

The impact of handwriting difficulties on compositional quality in children with developmental coordination disorder

Science.gov (United States)

Barnett, Anna L; Wilmut, Kate; Plumb, Mandy S

2016-01-01

Introduction There is substantial evidence to support the relationship between transcription skills (handwriting and spelling) and compositional quality. For children with developmental coordination disorder, handwriting can be particularly challenging. While recent research has aimed to investigate their handwriting difficulties in more detail, the impact of transcription on their compositional quality has not previously been examined. The aim of this exploratory study was to examine compositional quality in children with developmental coordination disorder and to ascertain whether their transcription skills influence writing quality. Method Twenty-eight children with developmental coordination disorder participated in the study, with 28 typically developing age and gender matched controls. The children completed the ‘free-writing’ task from the detailed assessment of speed of handwriting tool, which was evaluated for compositional quality using the Wechsler objective language dimensions. Results The children with developmental coordination disorder performed significantly below their typically developing peers on five of the six Wechsler objective language dimensions items. They also had a higher percentage of misspelled words. Regression analyses indicated that the number of words produced per minute and the percentage of misspelled words explained 55% of the variance for compositional quality. Conclusion The handwriting difficulties so commonly reported in children with developmental coordination disorder have wider repercussions for the quality of written composition. PMID:27807392

Osmium Isotope Compositions of Komatiite Sources Through Time

Science.gov (United States)

Walker, R. J.

2001-12-01

Extending Os isotopic measurements to ancient plume sources may help to constrain how and when the well-documented isotopic heterogeneities in modern systems were created. Komatiites and picrites associated with plume-related volcanism are valuable tracers of the Os isotopic composition of plumes because of their typically high Os concentrations and relatively low Re/Os. Re-Os data are now available for a variety of Phanerozoic, Proterozoic and Archean komatiites and picrites. As with modern plumes, the sources of Archean and Proterozoic komatiites exhibit a large range of initial 187Os/188Os ratios. Most komatiites are dominated by sources with chondritic Os isotopic compositions (e.g. Song La; Norseman-Wiluna; Pyke Hill; Alexo), though some (e.g. Gorgona) derive from heterogeneous sources. Of note, however, two ca. 2.7 Ga systems, Kostomuksha (Russia) and Belingwe (Zimbabwe), have initial ratios enriched by 2-3% relative to the contemporary convecting upper mantle. These results suggest that if the 187Os enrichment was due to the incorporation of minor amounts of recycled crust into the mantle source of the rocks, the crust formed very early in Earth history. Thus, the Os results could reflect derivation of melt from hybrid mantle whose composition was modified by the addition of mafic crustal material that would most likely have formed between 4.2 and 4.5 Ga. Alternately, the mantle sources of these komatiites may have derived a portion of their Os from the putative 187Os - and 186Os -enriched outer core. For this hypothesis to be applicable to Archean rocks, an inner core of sufficient mass would have to have crystallized sufficiently early in Earth history to generate an outer core with 187Os enriched by at least 3% relative to the chondritic average. Using the Pt-Re-Os partition coefficients espoused by our earlier work, and assuming linear growth of the inner core started at 4.5 Ga and continued to present, would yield an outer core at 2.7 Ga with a gamma Os

Impact source localisation in aerospace composite structures

Science.gov (United States)

De Simone, Mario Emanuele; Ciampa, Francesco; Boccardi, Salvatore; Meo, Michele

2017-12-01

The most commonly encountered type of damage in aircraft composite structures is caused by low-velocity impacts due to foreign objects such as hail stones, tool drops and bird strikes. Often these events can cause severe internal material damage that is difficult to detect and may lead to a significant reduction of the structure’s strength and fatigue life. For this reason there is an urgent need to develop structural health monitoring systems able to localise low-velocity impacts in both metallic and composite components as they occur. This article proposes a novel monitoring system for impact localisation in aluminium and composite structures, which is able to determine the impact location in real-time without a-priori knowledge of the mechanical properties of the material. This method relies on an optimal configuration of receiving sensors, which allows linearization of well-known nonlinear systems of equations for the estimation of the impact location. The proposed algorithm is based on the time of arrival identification of the elastic waves generated by the impact source using the Akaike Information Criterion. The proposed approach was demonstrated successfully on both isotropic and orthotropic materials by using a network of closely spaced surface-bonded piezoelectric transducers. The results obtained show the validity of the proposed algorithm, since the impact sources were detected with a high level of accuracy. The proposed impact detection system overcomes current limitations of other methods and can be retrofitted easily on existing aerospace structures allowing timely detection of an impact event.

OSSMETER D3.4 – Language-Specific Source Code Quality Analysis

NARCIS (Netherlands)

J.J. Vinju (Jurgen); A. Shahi (Ashim); H.J.S. Basten (Bas)

2014-01-01

htmlabstractThis deliverable is part of WP3: Source Code Quality and Activity Analysis. It provides descriptions and prototypes of the tools that are needed for source code quality analysis in open source software projects. It builds upon the results of: • Deliverable 3.1 where infra-structure and

A scope classification of data quality requirements for food composition data.

Science.gov (United States)

Presser, Karl; Hinterberger, Hans; Weber, David; Norrie, Moira

2016-02-15

Data quality is an important issue when managing food composition data since the usage of the data can have a significant influence on policy making and further research. Although several frameworks for data quality have been proposed, general tools and measures are still lacking. As a first step in this direction, we investigated data quality requirements for an information system to manage food composition data, called FoodCASE. The objective of our investigation was to find out if different requirements have different impacts on the intrinsic data quality that must be regarded during data quality assessment and how these impacts can be described. We refer to the resulting classification with its categories as the scope classification of data quality requirements. As proof of feasibility, the scope classification has been implemented in the FoodCASE system. Copyright © 2015 Elsevier Ltd. All rights reserved.

Automated geospatial Web Services composition based on geodata quality requirements

Science.gov (United States)

Cruz, Sérgio A. B.; Monteiro, Antonio M. V.; Santos, Rafael

2012-10-01

Service-Oriented Architecture and Web Services technologies improve the performance of activities involved in geospatial analysis with a distributed computing architecture. However, the design of the geospatial analysis process on this platform, by combining component Web Services, presents some open issues. The automated construction of these compositions represents an important research topic. Some approaches to solving this problem are based on AI planning methods coupled with semantic service descriptions. This work presents a new approach using AI planning methods to improve the robustness of the produced geospatial Web Services composition. For this purpose, we use semantic descriptions of geospatial data quality requirements in a rule-based form. These rules allow the semantic annotation of geospatial data and, coupled with the conditional planning method, this approach represents more precisely the situations of nonconformities with geodata quality that may occur during the execution of the Web Service composition. The service compositions produced by this method are more robust, thus improving process reliability when working with a composition of chained geospatial Web Services.

Portuguese food composition database quality management system.

Science.gov (United States)

Oliveira, L M; Castanheira, I P; Dantas, M A; Porto, A A; Calhau, M A

2010-11-01

The harmonisation of food composition databases (FCDB) has been a recognised need among users, producers and stakeholders of food composition data (FCD). To reach harmonisation of FCDBs among the national compiler partners, the European Food Information Resource (EuroFIR) Network of Excellence set up a series of guidelines and quality requirements, together with recommendations to implement quality management systems (QMS) in FCDBs. The Portuguese National Institute of Health (INSA) is the national FCDB compiler in Portugal and is also a EuroFIR partner. INSA's QMS complies with ISO/IEC (International Organization for Standardisation/International Electrotechnical Commission) 17025 requirements. The purpose of this work is to report on the strategy used and progress made for extending INSA's QMS to the Portuguese FCDB in alignment with EuroFIR guidelines. A stepwise approach was used to extend INSA's QMS to the Portuguese FCDB. The approach included selection of reference standards and guides and the collection of relevant quality documents directly or indirectly related to the compilation process; selection of the adequate quality requirements; assessment of adequacy and level of requirement implementation in the current INSA's QMS; implementation of the selected requirements; and EuroFIR's preassessment 'pilot' auditing. The strategy used to design and implement the extension of INSA's QMS to the Portuguese FCDB is reported in this paper. The QMS elements have been established by consensus. ISO/IEC 17025 management requirements (except 4.5) and 5.2 technical requirements, as well as all EuroFIR requirements (including technical guidelines, FCD compilation flowchart and standard operating procedures), have been selected for implementation. The results indicate that the quality management requirements of ISO/IEC 17025 in place in INSA fit the needs for document control, audits, contract review, non-conformity work and corrective actions, and users' (customers

Effects of processing on nutritional composition and quality

Indian Academy of Sciences (India)

The effects of processing on the nutritional composition and quality evaluation of ... P ≤ 0.01 ) differences in total dry matter and total sugar content between samples, ... Faculty of Tourism and Hospitality Management, Department of Nutrition, ...

Economics of Water Quality Protection from Nonpoint Sources: Theory and Practice

OpenAIRE

Ribaudo, Marc; Horan, Richard D.; Smith, Mark E.

1999-01-01

Water quality is a major environmental issue. Pollution from nonpoint sources is the single largest remaining source of water quality impairments in the United States. Agriculture is a major source of several nonpoint-source pollutants, including nutrients, sediment, pesticides, and salts. Agricultural nonpoint pollution reduction policies can be designed to induce producers to change their production practices in ways that improve the environmental and related economic consequences of produc...

Antifouling paint particles: Sources, occurrence, composition and dynamics.

Science.gov (United States)

Soroldoni, Sanye; Castro, Ítalo Braga; Abreu, Fiamma; Duarte, Fabio Andrei; Choueri, Rodrigo Brasil; Möller, Osmar Olinto; Fillmann, Gilberto; Pinho, Grasiela Lopes Leães

2018-06-15

Sources, occurrence, composition and dynamics of antifouling paint particles (APPs) were assessed in Patos Lagoon estuary (PLE), Southern Brazil. Ten areas including boatyards, a marina and artisanal fishing harbors were identified in the estuarine system as potential sources of APPs. The APPs generated in these areas were highly heterogeneous considering the size, shape and composition. Based on an estimate of antifouling paint usage and amount of boats in each studied area, artisanal fishing harbors could be the main source of particles to PLE. However, relatively high amounts of APPs, which ranged from 130 to 40,300 μg g -1 , were detected in sediments collected in front of boatyards and a marina. The uneven distribution of APPs levels among the sediment samples were probably due to the presence of diffuse sources (fishing harbors) associated to "hotspots" (boatyards and marina) along the study area. Additionally, data of settling experiment indicate that size, shape and density of APPs, combined to local hydrodynamics, appears to contribute to the mobility of these residues within the estuary. In the main channel of PLE, smaller particles tend to be transported to adjacent coastal zone while particles tend to be deposited in the sediment surface of sheltered areas. Since different trace metals, and booster biocides were detected in APPs that were not correctly disposed, these particles can be considered as an important source of contamination to aquatic environments. The present data suggest that APPs represent an environmental problem for aquatic systems in Brazil, since the country lacks legislation in addition to inefficient control mechanisms. An improvement in boat maintenance processes are urgently needed to avoid this continuous release of APPs into the aquatic systems. Copyright © 2018 Elsevier Ltd. All rights reserved.

Quality Assurance Source Requirements Traceability Database

International Nuclear Information System (INIS)

MURTHY, R.; NAYDENOVA, A.; DEKLEVER, R.; BOONE, A.

2006-01-01

At the Yucca Mountain Project the Project Requirements Processing System assists in the management of relationships between regulatory and national/industry standards source criteria, and Quality Assurance Requirements and Description document (DOE/R W-0333P) requirements to create compliance matrices representing respective relationships. The matrices are submitted to the U.S. Nuclear Regulatory Commission to assist in the commission's review, interpretation, and concurrence with the Yucca Mountain Project QA program document. The tool is highly customized to meet the needs of the Office of Civilian Radioactive Waste Management Office of Quality Assurance

The chemical composition and sources of PM2.5 during the 2009 Chinese New Year's holiday in Shanghai

Science.gov (United States)

Feng, Jialiang; Sun, Peng; Hu, Xiaoling; Zhao, Wei; Wu, Minghong; Fu, Jiamo

2012-11-01

China is virtually shut down during the week-long Chinese New Year's holiday. This implies that the anthropogenic emissions would be greatly decreased during the period thus providing an opportunity to study the air quality in China under reduced emissions, and the drastic emission changes during a short period of time allows the comparison of source contributions under significantly different conditions. Seventeen PM2.5 samples were collected during the 2009 Chinese New Year's holiday in Shanghai to study the composition and sources of the fine particles. Organic carbon (OC), elemental carbon (EC), eight water-soluble ions, fourteen metals and solvent extractable organic compounds (SEOC) including alkanes, hopanes, polycyclic aromatic hydrocarbons (PAHs) and fatty acids were measured. Diagnostic PAH ratios, correlation analysis of OC, EC, n-alkanes, hopanes and PAHs showed that vehicle emissions were the main source of n-alkanes and EC, and an important source of the locally emitted particulate PAHs in urban Shanghai, while coal burning should be the main source of the transported PAHs from the inland areas. The composition of n-fatty acids also provided some clue on the significance of the contribution by kitchen activities. In the New Year's Eve's sample, 75% of the particle mass was estimated to be from fireworks, and K+, SO42 -, Cl-, OC, Al and Ba were the main components. Firework fine particles had high OC/EC ratio and low NO3-/SO42 - ratio.

Impacts by point and diffuse micropollutant sources on the stream water quality at catchment scale

Science.gov (United States)

Petersen, M. F.; Eriksson, E.; Binning, P. J.; Bjerg, P. L.

2012-04-01

The water quality of surface waters is threatened by multiple anthropogenic pollutants and the large variety of pollutants challenges the monitoring and assessment of the water quality. The aim of this study was to characterize and quantify both point and diffuse sources of micropollutants impacting the water quality of a stream at catchment scale. Grindsted stream in western Jutland, Denmark was used as a study site. The stream passes both urban and agricultural areas and is impacted by severe groundwater contamination in Grindsted city. Along a 12 km reach of Grindsted stream, the potential pollution sources were identified including a pharmaceutical factory site with a contaminated old drainage ditch, two waste deposits, a wastewater treatment plant, overflow structures, fish farms, industrial discharges and diffuse agricultural and urban sources. Six water samples were collected along the stream and analyzed for general water quality parameters, inorganic constituents, pesticides, sulfonamides, chlorinated solvents, BTEXs, and paracetamol and ibuprofen. The latter two groups were not detected. The general water quality showed typical conditions for a stream in western Jutland. Minor impacts by releases of organic matter and nutrients were found after the fish farms and the waste water treatment plant. Nickel was found at concentrations 5.8 - 8.8 μg/l. Nine pesticides and metabolites of both agricultural and urban use were detected along the stream; among these were the two most frequently detected and some rarely detected pesticides in Danish water courses. The concentrations were generally consistent with other findings in Danish streams and in the range 0.01 - 0.09 μg/l; except for metribuzin-diketo that showed high concentrations up to 0.74 μg/l. The groundwater contamination at the pharmaceutical factory site, the drainage ditch and the waste deposits is similar in composition containing among others sulfonamides and chlorinated solvents (including vinyl

Quantifying the quality of precipitation data from different sources

Science.gov (United States)

Leijnse, Hidde; Wauben, Wiel; Overeem, Aart; de Haij, Marijn

2015-04-01

There is an increasing demand for high-resolution rainfall data. The current manual and automatic networks of climate and meteorological stations provide high quality rainfall data, but they cannot provide the high spatial and temporal resolution required for many applications. This can only partly be solved by using remotely sensed data. It is therefore necessary to consider third-party data, such as rain gauges operated by amateurs and rainfall intensities from commercial cellular communication links. The quality of such third-party data is highly variable and generally lower than that of dedicated networks. Often, such data quality information is missing for third party data. In order to be able to use data from various sources it is vital that quantitative knowledge of the data quality is available. This holds for all data sources, including the rain gauges in the reference networks of climate and meteorological stations. Data quality information is generally either not available or very limited for third-party data sources. For most dedicated climate meteorological networks, this information is only available for the sensor in laboratory conditions. In many cases, however, a significant part of the measurement errors and uncertainties is determined by the siting and maintenance of the sensor, for which generally only qualitative information is available. Furthermore sensors may have limitations under specific conditions. We aim to quantify data quality for different data sources by performing analyses on collocated data sets. Here we present an intercomparison of two years of precipitation data from six different sources (manual rain gauge, automatic rain gauge, present weather sensor, weather radar, commercial cellular communication links, and Meteosat) at three different locations in the Netherlands. We use auxiliary meteorological data to determine if the quality is influenced by other variables (e.g. the temperature influencing the evaporation from the

Water quality assessment of selected domestic water sources in ...

African Journals Online (AJOL)

However, lead ion appears higher than the approved WHO and SON standard for water quality in all the sources except that of water vendors which is 0.04mg/l. It is therefore recommended that periodic monitoring of water quality, effective waste management system to improve the general water quality in the town, and ...

Air quality dispersion models from energy sources

International Nuclear Information System (INIS)

Lazarevska, Ana

1996-01-01

Along with the continuing development of new air quality models that cover more complex problems, in the Clean Air Act, legislated by the US Congress, a consistency and standardization of air quality model applications were encouraged. As a result, the Guidelines on Air Quality Models were published, which are regularly reviewed by the Office of Air Quality Planning and Standards, EPA. These guidelines provide a basis for estimating the air quality concentrations used in accessing control strategies as well as defining emission limits. This paper presents a review and analysis of the recent versions of the models: Simple Terrain Stationary Source Model; Complex Terrain Dispersion Model; Ozone,Carbon Monoxide and Nitrogen Dioxide Models; Long Range Transport Model; Other phenomenon Models:Fugitive Dust/Fugitive Emissions, Particulate Matter, Lead, Air Pathway Analyses - Air Toxic as well as Hazardous Waste. 8 refs., 4 tabs., 2 ills

Physicochemical composition and glycemic index of whole grain bread produced from composite flours of quality protein maize and wheat

Directory of Open Access Journals (Sweden)

C. T. Akanbi

2016-01-01

Full Text Available This study entails quality assessment of whole grain bread produced from composite flours of quality protein maize and wheat. Quality protein maize and wheat were processed into flours and mixed at various ratios for bread production. The proximate compositions, physical properties, glycemic response, functional and sensory properties of the samples were evaluated using standard methods. The result showed no significant difference (p<0.05 in the proximate composition parameters of the bread samples. The loaf height (2.50 - 3.95 cm, volume (291.00 - 415.00 cm3 and specific volume(1.72 - 2.42 cm3/g decreased significantly with increasing level of quality protein maize, however, loaf length was not affected by the substitution of quality protein maize. The result of the functional properties showed that final viscosity, water absorption and swelling capacity increased with increasing level of quality protein maize. The result of the glycemic response showed that the inclusion of quality protein maize resulted in decline in the blood glucose content (glycemic index of the products. The bread samples were generally acceptable however; bread with 100% wheat was the most preferred. The result of the sensory properties showed that there was significant difference (p<0.05 in the texture and taste of 100% wheat bread and the other samples. The study concluded that substitution of quality protein maize with wheat produced acceptable whole grain loaves that have positive effect on the reduction of blood glucose level.

Influence of the temperature on the composites' fusion bonding quality

Science.gov (United States)

Harkous, Ali; Jurkowski, Tomasz; Bailleul, Jean-Luc; Le Corre, Steven

2017-10-01

Thermoplastic composite parts are increasingly used to replace metal pieces in automotive field due to their mechanical properties, chemical properties and recycling potential [1]. To assemble and give them new mechanical functions, fusion bonding is often used. It is a type of welding carried out at a higher temperature than the fusion one [2]. The mechanical quality of the final adhesion depends on the process parameters like pressure, temperature and cycle time [3]. These parameters depend on two phenomena at the origin of the bonding formation: intimate contact [4] and reptation and healing [5]. In this study, we analyze the influence of the temperature on the bonding quality, disregarding in this first steps the pressure influence. For that, two polyamide composite parts are welded using a specific setup. Then, they undergo a mechanical test of peeling in order to quantify the adhesion quality.

Sourcing for Quality: Cooperating with a Single Supplier or Developing Two Competing Suppliers?

Directory of Open Access Journals (Sweden)

Jingxian Chen

2016-01-01

Full Text Available Supplier efforts regarding product quality are an important issue in outsourcing and play a critical role in a manufacturer’s choice of sourcing strategy. Consider a manufacturer that wants to outsource the manufacturing of two substitute products to external suppliers. This paper studies the strategic interactions under two sourcing strategies: single and dual sourcing. A four-stage noncooperative game model is established to describe each member’s decisions. We further propose four decision scenarios: single sourcing with and without manufacturer quality investment sharing and dual sourcing when suppliers cooperate or do not cooperate on quality decisions. By the backward induction approach, we obtain analytical equilibrium solutions for each decision scenario. By comparing each pair of equilibrium profiles, we find that an appropriate proportion of quality investment sharing by the manufacturer can enable a cooperating strategy with a single supplier to be the dominant strategy. When the manufacturer does not want to share or does not want to share a relatively large portion of its supplier’s quality investment, it will always prefer to develop two competing suppliers when the cost of dual sourcing is sufficiently low. However, dual sourcing can be extremely risky for the manufacturer because the suppliers could provide a relatively low product quality level by cooperating on the quality decision to extract the manufacturer’s profit.

Data Quality Indicators Composition and Calculus: Engineering and Information Systems Approaches

Directory of Open Access Journals (Sweden)

Leon REZNIK

2015-02-01

Full Text Available Big Data phenomenon is a result of novel technological developments in sensor, computer and communication technologies. Nowadays more and more data are produced by nanoscale photonic, optoelectronic and electronic devices. However, their quality characteristics could be very low. The paper proposes new methods of the data management with huge data amounts that is based on associating of data quality indicators with each data entity. To achieve this goal, one needs to define the composition of the data quality indicators and to develop their integration calculus. As data quality evaluation involves multi-disciplinary research, various metrics have been investigated. The paper describes two major approaches in assigning the data quality indicators and developing their integration calculus. The information systems approach employs traditional high-level metrics like data accuracy, consistency and completeness. The engineering approach utilizes signal characteristics processed with the probability based calculus. The data quality metrics composition and calculus are discussed. The tools developed to automate the metrics selection and calculus procedures are presented. The user- friendly interface examples are provided.

Qualities of online friendships with different gender compositions and durations.

Science.gov (United States)

Cheng, Grand H L; Chan, Darius K S; Tong, Po Yee

2006-02-01

This study was designed to examine the qualities of online friendships with different gender compositions that had been maintained for varying periods of time. A total of 167 Hong Kong Internet-users rated the qualities of their same-sex and cross-sex online friendships on measures such as intimacy, trust, self-disclosure, and relational satisfaction. A 2 (gender of respondents: male vs. female) x 2 (gender of online friends: same-sex vs. opposite-sex) x 3 (duration of friendships: less than 1 year vs. 1-2 years vs. more than 2 years) factorial design was adopted. MANOVA results reveal the three-way interaction effect on intimacy, trust, and relational satisfaction. Specifically, the qualities of male-female, female-male, and female-female online friendships were generally higher for those with a longer duration than those at the early stage of friendship development. However, the qualities of male-male friendships that had been maintained for more than 2 years were lower than those maintained for 2 years or less. These findings suggest that qualities of online friendships are subject to effects of gender composition and duration. The conceptual implications of these results are discussed.

Compositional characteristics and industrial qualities of talcose rock ...

African Journals Online (AJOL)

Compositional characteristics and industrial qualities of talcose rock in Erin Omu area, southwestern Nigeria. OA Okunlola, FA Anikulapo. Abstract. No Abstract. Journal of Mining and Geology Vol. 42 (2) 2006: pp. 105-112. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.

Heuristic Model Of The Composite Quality Index Of Environmental Assessment

Science.gov (United States)

Khabarov, A. N.; Knyaginin, A. A.; Bondarenko, D. V.; Shepet, I. P.; Korolkova, L. N.

2017-01-01

The goal of the paper is to present the heuristic model of the composite environmental quality index based on the integrated application of the elements of utility theory, multidimensional scaling, expert evaluation and decision-making. The composite index is synthesized in linear-quadratic form, it provides higher adequacy of the results of the assessment preferences of experts and decision-makers.

A quality control program for radiation sources

International Nuclear Information System (INIS)

Almeida, C.E. de; Sibata, C.H.; Cecatti, E.R.; Kawakami, N.S.; Alexandre, A.C.; Chiavegatti Junior, M.

1982-01-01

An extensive quality control program was established covering the following areas: physical parameters of the therapeutical machines, dosimetric standards, preventive maintenance of radiation sources and measuring instruments. A critical evaluation of this program was done after two years (1977-1979) of routine application and the results will be presented. The fluctuation on physical parameters strongly supports the efforts and cost of a quality control program. This program has certainly improved the accuracy required on the delivery of the prescribed dose for radiotherapy treatment. (Author) [pt

A PRESSURE ULCER AND FALL RATE QUALITY COMPOSITE INDEX FOR ACUTE CARE UNITS: A MEASURE DEVELOPMENT STUDY

Science.gov (United States)

Jayawardhana, Ananda; Burman, Mary E.; Dunton, Nancy E.; Staggs, Vincent S.; Bergquist-Beringer, Sandra; Gajewski, Byron J.

2016-01-01

Background Composite indices are single measures that combine the strengths of two or more individual measures and provide broader, easy-to-use measures for evaluation of provider performance and comparisons across units and hospitals to support quality improvement. Objective The study objective was to develop a unit-level inpatient composite nursing care quality performance index – the Pressure Ulcer and Fall Rate Quality Composite Index. Design Two-phase measure development study. Settings 5,144 patient care units in 857 United States hospitals participating in the National Database of Nursing Quality Indictors® during the year 2013. Methods The Pressure Ulcer and Fall Rate Quality Composite Index was developed in two phases. In Phase 1 the formula was generated using a utility function and generalized penalty analysis. Experts with experience in healthcare quality measurement provided the point of indicator equivalence. In Phase 2 initial validity evidence was gathered based on hypothesized relationships between the Pressure Ulcer and Fall Rate Quality Composite Index and other variables using two-level (unit, hospital) hierarchical linear mixed modeling. Results The Pressure Ulcer and Fall Rate Quality Composite Index = 100 − PUR − FR, where PUR is pressure ulcer rate and FR is total fall rate. Higher scores indicate better quality. Bland-Altman plots demonstrated agreement between pairs of experts and provided evidence for inter-rater reliability of the formula. The validation process demonstrated that higher registered nurse skill mix, higher percent of registered nurses with a baccalaureate in nursing or higher degree, higher percent of registered nurses with national specialty certification, and lower percent of hours supplied by agency staff were significantly associated with higher Pressure Ulcer and Fall Rate Quality Composite Index scores. Higher percentages of unit patients at risk for a hospital-acquired pressure ulcer and higher unit rates of

Connectivity and propagule sources composition drive ditch plant metacommunity structure

Science.gov (United States)

Favre-Bac, Lisa; Ernoult, Aude; Mony, Cendrine; Rantier, Yann; Nabucet, Jean; Burel, Françoise

2014-11-01

The fragmentation of agricultural landscapes has a major impact on biodiversity. In addition to habitat loss, dispersal limitation increasingly appears as a significant driver of biodiversity decline. Landscape linear elements, like ditches, may reduce the negative impacts of fragmentation by enhancing connectivity for many organisms, in addition to providing refuge habitats. To characterize these effects, we investigated the respective roles of propagule source composition and connectivity at the landscape scale on hydrochorous and non-hydrochorous ditch bank plant metacommunities. Twenty-seven square sites (0.5 km2 each) were selected in an agricultural lowland of northern France. At each site, plant communities were sampled on nine ditch banks (totaling 243 ditches). Variables characterizing propagule sources composition and connectivity were calculated for landscape mosaic and ditch network models. The landscape mosaic influenced only non-hydrochorous species, while the ditch network impacted both hydrochorous and non-hydrochorous species. Non-hydrochorous metacommunities were dependent on a large set of land-use elements, either within the landscape mosaic or adjacent to the ditch network, whereas hydrochorous plant metacommunities were only impacted by the presence of ditches adjacent to crops and roads. Ditch network connectivity also influenced both hydrochorous and non-hydrochorous ditch bank plant metacommunity structure, suggesting that beyond favoring hydrochory, ditches may also enhance plant dispersal by acting on other dispersal vectors. Increasing propagule sources heterogeneity and connectivity appeared to decrease within-metacommunity similarity within landscapes. Altogether, our results suggest that the ditch network's composition and configuration impacts plant metacommunity structure by affecting propagule dispersal possibilities, with contrasted consequences depending on species' dispersal vectors.

Advances in Mineral Dust Source Composition Measurement with Imaging Spectroscopy at the Salton Sea, CA

Science.gov (United States)

Green, R. O.; Realmuto, V. J.; Thompson, D. R.; Mahowald, N. M.; Pérez García-Pando, C.; Miller, R. L.; Clark, R. N.; Swayze, G. A.; Okin, G. S.

2015-12-01

Mineral dust emitted from the Earth's surface is a principal contributor to direct radiative forcing over the arid regions, where shifts in climate have a significant impact on agriculture, precipitation, and desert encroachment around the globe. Dust particles contribute to both positive and negative forcing, depending on the composition of the particles. Particle composition is a function of the surface mineralogy of dust source regions, but poor knowledge of surface mineralogy on regional to global scales limits the skill of Earth System models to predict shifts in regional climate around the globe. Earth System models include the source, emission, transport and deposition phases of the dust cycle. In addition to direct radiative forcing contributions, mineral dust impacts include indirect radiative forcing, modification of the albedo and melting rates of snow and ice, kinetics of tropospheric photochemistry, formation and deposition of acidic aerosols, supply of nutrients to aquatic and terrestrial ecosystems, and impact on human health and safety. We demonstrate the ability to map mineral dust source composition in the Salton Sea dust source region with imaging spectroscopy measurements acquired as part of the NASA HyspIRI preparatory airborne campaign. These new spectroscopically derived compositional measurements provide a six orders of magnitude improvement over current atlases for this dust source region and provide a pathfinder example for a remote measurement approach to address this critical dust composition gap for global Earth System models.

A Practical Method of Acoustic Emission Source Location in Anisotropic Composite Laminates

Energy Technology Data Exchange (ETDEWEB)

Kim, Jeong Kon; Kang, Yong Kyu; Kwon, Oh Yang [Inha University, Incheon (Korea, Republic of)

2003-06-15

Since the velocity is dependent on the fiber orientation in anisotropic composites, the application of traditional acoustic emission (AE) source location techniques based on the constant velocity to composite structures has been practically impossible. The anisotropy makes the source location procedure complicated and deteriorates the accuracy of the location. In this study, we have divided the region of interest(ROI) into a set of finite elements, taken each element as a virtual source, and calculated the arrival time differences between sensors by using the velocities at every degree from 0 to 90. The calculated and the experimentally measured values of the arrival time difference aye then compared to minimize the location error. The results from two different materials, namely AA6061-T6 and CFRP(uni-directional; UD, [0]{sub 32}4 ) laminate confirmed the practical usefulness of the proposed method

Dose performance and image quality: Dual source CT versus single source CT in cardiac CT angiography

International Nuclear Information System (INIS)

Wang Min; Qi Hengtao; Wang Ximing; Wang Tao; Chen, Jiu-Hong; Liu Cheng

2009-01-01

Objective: To evaluate dose performance and image quality of 64-slice dual source CT (DSCT) in comparison to 64-slice single source CT (SSCT) in cardiac CT angiography (CTA). Methods: 100 patients examined by DSCT and 60 patients scanned by SSCT were included in this study. Objective indices such as image noise, contrast-to-noise ratio and signal-to-noise ratio were analyzed. Subjective image quality was assessed by two cardiovascular radiologists in consensus using a four-point scale (1 = excellent to 4 = not acceptable). Estimation of effective dose was performed on the basis of dose length product (DLP). Results: At low heart rates ( 0.05), but, at high heart rates (>70 bpm), DSCT provided robust image quality (P 70 bpm), DSCT is able to provide robust diagnostic image quality at doses far below that of SSCT.

Surface-water, water-quality, and meteorological data for the Cambridge, Massachusetts, drinking-water source area, water years 2007-08

Science.gov (United States)

Smith, Kirk P.

2011-01-01

Records of water quantity, water quality, and meteorological parameters were continuously collected from three reservoirs, two primary streams, and five subbasin tributaries in the Cambridge, Massachusetts, drinking-water source area during water years 2007-08 (October 2006 through September 2008). Water samples were collected during base-flow conditions and storms in the Cambridge Reservoir and Stony Brook Reservoir drainage areas and analyzed for dissolved calcium, sodium, chloride, and sulfate; total nitrogen and phosphorus; and polar pesticides and metabolites. Composite samples of stormwater also were analyzed for concentrations of total petroleum hydrocarbons and suspended sediment in one subbasin in the Stony Brook Reservoir drainage basin. These data were collected to assist watershed administrators in managing the drinking-water source area and to identify potential sources of contaminants and trends in contaminant loading to the water supply.

Quality assurance in the transport of radiography sources

International Nuclear Information System (INIS)

Parihar, Manju; Singh, R.K.; Upadhyay, K.C.; Agarwal, S.P.

2001-01-01

One of the applications of radioisotopes in industry is non destructive testing (NDT) where the industrial radiography sources are often transported in public domain for site radiography. About 1100 cameras are deployed in our country. This transport of the sources can lead to significant radiological impact in case of accidents unless all precautions are taken. It is, therefore, required to have a systematic programme of controls and inspections in the transport of radioactive source. In this paper, we discuss the quality assurance programme that should be applied in various stages of the transport of radioactive sources to ensure a safe transport and prompt delivery of the radioactive consignment at its destination. (author)

Particulate Matter Sources and Composition near a Shrinking Saline Lake (Salton Sea)

Science.gov (United States)

Frie, A. L.; Dingle, J. H.; Garrison, A.; Ying, S.; Bahreini, R.

2017-12-01

Dried lake beds (playas) are large dust sources in arid regions, and with increased global water demand many large lakes are shrinking. The Salton Sea is an example of one such lake in the early stages of desiccation, with about 15,000 acres of exposed playa. To quantify the impacts of the shrinking lake on airborne particulate matter(PM) composition, PM samples were collected in August of 2015 and February of 2016 near the Salton Sea, CA. These samples were analyzed for total elemental concentration of 15 elements. For these elements, enrichment factors relative to aluminum were calculated and PMF modeling was applied to deconvolve source factors. From these data, desert-like and playa-like sources were estimated to accounted for 45% and 9% of PM10 mass during these sampling periods. PMF results also revealed that playa sources account for 70% of PM10 Na, evidencing playa-driven PM compositional changes. Additionally, PM Se displayed strong seasonal variation, which is thought to be driven by Se volatilization within Salton Sea sediments, playas, or waters.

Effect of low emission sources on air quality in Cracow

Energy Technology Data Exchange (ETDEWEB)

Nedoma, J. [EKOPOL Environmental Engineering Studies and Design Office, Co. Ltd., Cracow (Poland)

1995-12-31

The paper presents calculation of power engineering low emission and results of stimulation of the effect of this emission on air quality in Cracow, Poland. It has been stated that the segment of low emission in central areas of the town makes up ca. 40% of the observed concentration of sulfur dioxide. Furthermore it has been stated that the capital investment must be concentrated in the central part of the town in order to reach noticeable improvement of air quality in Cracow. Neither the output of a separate power source nor the emission level and its individual harmful effect, but the location of the source and especially packing density of the sources must decide the priority of upgrading actions.

SPECIEUROPE: The European data base for PM source profiles

OpenAIRE

PERNIGOTTI DENISE; BELIS CLAUDIO; SPANO' LUCA

2015-01-01

A database of atmospheric particulate matter emission source profiles in Europe (SPECIEUROPE) was developed by the Joint Research Center in the framework of the Forum for air quality modeling in Europe (FAIRMODE, Working Group 3). It contains the chemical composition of particulate matter (PM) emission sources reported in the scientific literature and reports drafted by competent authorities. The first release of SPECIEUROPE consists of 151 measured profiles (original), 13 composite (merging ...

Heat-source specification 500 watt(e) RTG

International Nuclear Information System (INIS)

1983-02-01

This specification establishes the requirements for a 90 SrF 2 heat source and its fuel capsule for application in a 500 W(e) thermoelectric generator. The specification covers: fuel composition and quantity; the Hastelloy S fuel capsule material and fabrication; and the quality assurance requirements for the assembled heat source

The Dietary Composition and Source of Macronutrients Determine Obesity Development

DEFF Research Database (Denmark)

Myrmel, Lene Secher

The drastic worldwide increase in obesity during the last decades is accompanied with several different health disorders. The underlying mechanisms for this escalation is not clear, but certain alterations in the dietary macronutrient composition are suggested to be of importance. In addition...... fat and marine oils. To further investigate the importance of the macronutrient composition on obesity development, we have performed a series of mice experiments. Our results demonstrate that both the amount and source of macronutrients influence obesity development and related disorders. The anti...... to attenuate obesity development. The gut microbiota is less affected by alterations in protein:carbohydrate ratio and adiposity, but is altered in response to an elevated fat intake. The macronutrient composition is able to affect obesity development through direct influence on energy consuming metabolic...

How reservoirs alter drinking water quality: Organic matter sources, sinks, and transformations

Science.gov (United States)

Kraus, Tamara E.C.; Bergamaschi, Brian A.; Hernes, Peter J.; Doctor, Daniel H.; Kendall, Carol; Downing, Bryan D.; Losee, Richard F.

2011-01-01

Within reservoirs, production, transformation, and loss of dissolved organic matter (DOM) occur simultaneously. While the balance between production and loss determines whether a reservoir is a net sink or source of DOM, changes in chemical composition are also important because they affect DOM reactivity with respect to disinfection by-product (DBP) formation. The composition of the DOM pool also provides insight into DOM sources and processing, which can inform reservoir management. We examined the concentration and composition of DOM in San Luis Reservoir, a large off-stream impoundment of the California State Water Project. We used a wide array of DOM chemical tracers including dissolved organic carbon (DOC) concentration, trihalomethane and haloacetic acid formation potentials (THMFP and HAAFP, respectively), absorbance properties, isotopic composition, lignin phenol content, and structural groupings determined by 13C nuclear magnetic resonance (NMR). There were periods when the reservoir was a net source of DOC due to the predominance of algal production (summer), a net sink due to the predominance of degradation (fall–winter), and balanced between production and consumption (spring). Despite only moderate variation in bulk DOC concentration (3.0–3.6 mg C/L), changes in DOM composition indicated that terrestrial-derived material entering the reservoir was being degraded and replaced by aquatic-derived DOM produced within the reservoir. Substantial changes in the propensity of the DOM pool to form THMs and HAAs illustrate that the DBP precursor pool was not directly coupled to bulk DOC concentration and indicate that algal production is an important source of DBP precursors. Results suggest reservoirs have the potential to attenuate DOM amount and reactivity with respect to DBP precursors via degradative processes; however, these benefits can be decreased or even negated by the production of algal-derived DOM.

The effect of the boron source composition ratio on the adsorption performance of hexagonal boron nitride without a template

Energy Technology Data Exchange (ETDEWEB)

Zhang, Ning, E-mail: zhangning5832@163.com; Zhang, Tong; Kan, Hongmin; Wang, Xiaoyang; Long, Haibo; Cui, Xingyu

2015-08-01

An inexpensive boric acid (H{sub 3}BO{sub 3}) and borax (Na{sub 2}B{sub 4}O{sub 7}·10H{sub 2}O) mix was used as a source of boron with different composition ratios, and urea was used as a nitrogen source, in flowing ammonia atmosphere, for the preparation of hexagonal boron nitride (h-BN) with different micro-morphologies. Under a certain synthesis process, the effects of the molar ratio of borax and boric acid (or simply the boron source composition ratio for short) on the phase composition of the sample were studied; the work also explored the effect of boron source composition ratio on the micro-morphology, adsorption desorption isotherm and specific surface area of the h-BN powder. The main purpose of this work was to determine the optimum composition ratio of preparing spherical mesoporous h-BN and ensure that the micro-mechanism underpinning the formation of spherical mesoporous h-BN was understood. The results showed that at the optimum boron source composition ratio of 1:1, globular mesoporous spheres with a diameter of approximately 600–800 nm could be obtained with the highest pore volume and specific surface area (230.2 m{sup 2}/g). - Graphical abstract: Display Omitted - Highlights: • Spherical h-BN was synthesized by controlling the boron source composition ratio. • Without extra spherical template, solid Na{sub 2}O was equal to a spherical template. • At boron source composition ratio of 1:1, h-BN had best adsorption performance.

THE PRODUCTION AND BODY COMPOSITION OF KACANG GOAT FED DIFFERENT QUALITY OF DIETS

Directory of Open Access Journals (Sweden)

V. Restitrisnani

2014-10-01

Full Text Available An experimental study was carried out to assess the effect of diet quality on productivity and bodycomposition of Kacang goat. Fifteen male Kacang goats weighing 14.28 ± 3.36 kg (CV = 23.55% weredivided into 5 groups based on body weight. The experimental design used in this study wasRandomized Block Design (RBD with 3 treatments of dietary protein and total digestible (TDNcontents (T1= diet with 9.20% protein and 54.67% TDN; T2= diet with 11.6% protein and 58.61%TDN; T3= diet with 18.33% protein and 65.23% TDN. Parameters observed were feed intake, drymatter intake, crude protein intake, TDN intake, live weight gain (LWG and body composition ofKacang goat. The results showed that feed quality did not significantly affect (P>0.05 dry matter intakeand body composition, but significantly affect (P<0.05 protein intake, TDN intake and LWG. It can beconcluded that the higher quality diet resulted in higher productivity, but the higher quality diet was notaffect body composition of Kacang goat, except body fat gain (%.

Impact source location on composite CNG storage tank using acoustic emission energy based signal mapping method

Energy Technology Data Exchange (ETDEWEB)

Han, Byeong Hee; Yoon, Dong Jin; Park, Chun Soo [Korea Research Institute of Standards and Science, Center for Safety Measurement, Daejeon (Korea, Republic of); Lee, Young Shin [Dept. of Mechanical Design Engineering, Chungnam National University, Daejeon (Korea, Republic of)

2016-10-15

Acoustic emission (AE) is one of the most powerful techniques for detecting damages and identify damage location during operations. However, in case of the source location technique, there is some limitation in conventional AE technology, because it strongly depends on wave speed in the corresponding structures having heterogeneous composite materials. A compressed natural gas(CNG) pressure vessel is usually made of carbon fiber composite outside of vessel for the purpose of strengthening. In this type of composite material, locating impact damage sources exactly using conventional time arrival method is difficult. To overcome this limitation, this study applied the previously developed Contour D/B map technique to four types of CNG storage tanks to identify the source location of damages caused by external shock. The results of the identification of the source location for different types were compared.

Bacterial composition in a metropolitan drinking water distribution system utilizing different source waters.

Science.gov (United States)

Gomez-Alvarez, Vicente; Humrighouse, Ben W; Revetta, Randy P; Santo Domingo, Jorge W

2015-03-01

We investigated the bacterial composition of water samples from two service areas within a drinking water distribution system (DWDS), each associated with a different primary source of water (groundwater, GW; surface water, SW) and different treatment process. Community analysis based on 16S rRNA gene clone libraries indicated that Actinobacteria (Mycobacterium spp.) and α-Proteobacteria represented nearly 43 and 38% of the total sequences, respectively. Sequences closely related to Legionella, Pseudomonas, and Vibrio spp. were also identified. In spite of the high number of sequences (71%) shared in both areas, multivariable analysis revealed significant differences between the GW and SW areas. While the dominant phylotypes where not significantly contributing in the ordination of samples, the populations associated with the core of phylotypes (1-10% in each sample) significantly contributed to the differences between both service areas. Diversity indices indicate that the microbial community inhabiting the SW area is more diverse and contains more distantly related species coexisting with local assemblages as compared with the GW area. The bacterial community structure of SW and GW service areas were dissimilar, suggesting that their respective source water and/or water quality parameters shaped by the treatment processes may contribute to the differences in community structure observed.

Power quality enhancement of renewable energy source power network using SMES system

International Nuclear Information System (INIS)

Seo, H.R.; Kim, A.R.; Park, M.; Yu, I.K.

2011-01-01

Power quality enhancement of a renewable energy source power network is performed by a real-toroidal-type SMES coil. SMES unit charges and discharges the HTS coil to mitigate the fluctuation of PV system output power. The grid connected PV and SMES system has been modeled and simulated using power-hard-in-the-loop simulation. The PHILS results demonstrated the effectiveness of the SMES system for enhancing power quality. This paper deals with power quality enhancement of renewable energy source power network using SMES system and describes the operation characteristics of HTS SMES system using real-toroidal-type SMES coil for smoothening the fluctuation of large-scale renewable energy source such as photovoltaic (PV) power generation system. It generates maximum power of PV array under various weather conditions. SMES unit charges and discharges the HTS coil to mitigate the fluctuation of PV system output power. The SMES unit is controlled according to the PV array output and the utility power quality conditions. The grid connected PV and SMES system has been modeled and simulated using power-hard-in-the-loop simulation (PHILS). The PHILS results demonstrated the effectiveness of the SMES system for enhancing power quality in power network including large-scale renewable energy source, especially PV power generation system.

Using Wild Olives in Breeding Programs: Implications on Oil Quality Composition

Directory of Open Access Journals (Sweden)

Lorenzo León

2018-02-01

Full Text Available A wide genetic diversity has been reported for wild olives, which could be particularly interesting for the introgression of some agronomic traits and resistance to biotic and abiotic stresses in breeding programs. However, the introgression of some beneficial wild traits may be paralleled by negative effects on some other important agronomic and quality traits. From the quality point of view, virgin olive oil (VOO from olive cultivars is highly appreciated for its fatty acid composition (high monounsaturated oleic acid content and the presence of several minor components. However, the composition of VOO from wild origin and its comparison with VOO from olive cultivars has been scarcely studied. In this work, the variability for fruit characters (fruit weight and oil content, OC, fatty acid composition, and minor quality components (squalene, sterols and tocopherols content and composition was studied in a set of plant materials involving three different origins: wild genotypes (n = 32, cultivars (n = 62 and genotypes belonging to cultivar × wild progenies (n = 62. As expected, values for fruit size and OC in wild olives were lower than those obtained in cultivated materials, with intermediate values for cultivar × wild progenies. Wild olives showed a remarkably higher C16:0 percentage and tocopherol content in comparison to the cultivars. Contrarily, lower C18:1 percentage, squalene and sterol content were found in the wild genotypes, while no clear differences were found among the different plant materials regarding composition of the tocopherol and phytosterol fractions. Some common highly significant correlations among components of the same chemical family were found in all groups of plant materials. However, some other correlations were specific for one of the groups. The results of the study suggested that the use of wild germplasm in olive breeding programs will not have a negative impact on fatty acid composition, tocopherol content

Intra- and interspecific differences in diet quality and composition in a large herbivore community.

Directory of Open Access Journals (Sweden)

Claire Redjadj

Full Text Available Species diversity in large herbivore communities is often explained by niche segregation allowed by differences in body mass and digestive morphophysiological features. Based on large number of gut samples in fall and winter, we analysed the temporal dynamics of diet composition, quality and interspecific overlap of 4 coexisting mountain herbivores. We tested whether the relative consumption of grass and browse differed among species of different rumen types (moose-type and intermediate-type, whether diet was of lower quality for the largest species, whether we could identify plant species which determined diet quality, and whether these plants, which could be "key-food-resources" were similar for all herbivores. Our analyses revealed that (1 body mass and rumen types were overall poor predictors of diet composition and quality, although the roe deer, a species with a moose-type rumen was confirmed as an "obligatory non grazer", while red deer, the largest species, had the most lignified diet; (2 diet overlap among herbivores was well predicted by rumen type (high among species of intermediate types only, when measured over broad plant groups, (3 the relationship between diet composition and quality differed among herbivore species, and the actual plant species used during winter which determined the diet quality, was herbivore species-specific. Even if diets overlapped to a great extent, the species-specific relationships between diet composition and quality suggest that herbivores may select different plant species within similar plant group types, or different plant parts and that this, along with other behavioural mechanisms of ecological niche segregation, may contribute to the coexistence of large herbivores of relatively similar body mass, as observed in mountain ecosystems.

Investigating the effects of point source and nonpoint source pollution on the water quality of the East River (Dongjiang) in South China

Science.gov (United States)

Wu, Yiping; Chen, Ji

2013-01-01

Understanding the physical processes of point source (PS) and nonpoint source (NPS) pollution is critical to evaluate river water quality and identify major pollutant sources in a watershed. In this study, we used the physically-based hydrological/water quality model, Soil and Water Assessment Tool, to investigate the influence of PS and NPS pollution on the water quality of the East River (Dongjiang in Chinese) in southern China. Our results indicate that NPS pollution was the dominant contribution (>94%) to nutrient loads except for mineral phosphorus (50%). A comprehensive Water Quality Index (WQI) computed using eight key water quality variables demonstrates that water quality is better upstream than downstream despite the higher level of ammonium nitrogen found in upstream waters. Also, the temporal (seasonal) and spatial distributions of nutrient loads clearly indicate the critical time period (from late dry season to early wet season) and pollution source areas within the basin (middle and downstream agricultural lands), which resource managers can use to accomplish substantial reduction of NPS pollutant loadings. Overall, this study helps our understanding of the relationship between human activities and pollutant loads and further contributes to decision support for local watershed managers to protect water quality in this region. In particular, the methods presented such as integrating WQI with watershed modeling and identifying the critical time period and pollutions source areas can be valuable for other researchers worldwide.

Relationships between nutrient composition of flowers and fruit quality in orange trees grown in calcareous soil.

Science.gov (United States)

Pestana, Maribela; Beja, Pedro; Correia, Pedro José; de Varennes, Amarilis; Faria, Eugénio Araújo

2005-06-01

To determine if flower nutrient composition can be used to predict fruit quality, a field experiment was conducted over three seasons (1996-1999) in a commercial orange orchard (Citrus sinensis (L.) Osbeck cv. 'Valencia Late', budded on Troyer citrange rootstock) established on a calcareous soil in southern Portugal. Flowers were collected from 20 trees during full bloom in April and their nutrient composition determined, and fruits were harvested the following March and their quality evaluated. Patterns of covariation in flower nutrient concentrations and in fruit quality variables were evaluated by principal component analysis. Regression models relating fruit quality variables to flower nutrient composition were developed by stepwise selection procedures. The predictive power of the regression models was evaluated with an independent data set. Nutrient composition of flowers at full bloom could be used to predict the fruit quality variables fresh fruit mass and maturation index in the following year. Magnesium, Ca and Zn concentrations measured in flowers were related to fruit fresh mass estimations and N, P, Mg and Fe concentrations were related to fruit maturation index. We also established reference values for the nutrient composition of flowers based on measurements made in trees that produced large (> 76 mm in diameter) fruit.

Identification of sources and mechanisms of salt-water pollution ground-water quality

International Nuclear Information System (INIS)

Richter, B.C.; Dutton, A.R.; Kreitler, C.W.

1990-01-01

This book reports on salinization of soils and ground water that is widespread in the Concho River watershed and other semiarid areas in Texas and the United States. Using more than 1,200 chemical analyses of water samples, the authors were able to differentiate various salinization mechanisms by mapping salinity patterns and hydrochemical facies and by analyzing isotopic compositions and ionic ratios. Results revealed that in Runnels County evaporation of irrigation water and ground water is a major salinization mechanism, whereas to the west, in Irion and Tom Green Counties, saline water appears to be a natural mixture of subsurface brine and shallowly circulating meteoric water recharged in the Concho River watershed. The authors concluded that the occurrence of poor-quality ground water is not a recent or single-source phenomenon; it has been affected by terracing of farmland, by disposal of oil-field brines into surface pits, and by upward flow of brine from the Coleman Junction Formation via insufficiently plugged abandoned boreholes

Grandmothers Raising Grandchildren with Disabilities: Sources of Support and Family Quality of Life

Science.gov (United States)

Kresak, Karen E.; Gallagher, Peggy A.; Kelley, Susan J.

2014-01-01

Sources of support and quality of life of 50 grandmother-headed families raising grandchildren with and without disabilities were examined. Comparative analyses revealed significant differences between grandmothers raising grandchildren with and without disabilities in regard to sources of support and family quality of life. Informal support was…

Total quality at source

International Nuclear Information System (INIS)

Chiandone, A.C.

1990-01-01

The Total Quality at Source philosophy is based on optimizing the effectiveness of people in achieving ZERO-DEFECT results. In this paper a philosophy of what, I have come to perceive, it takes to get people to perform to the very best of their abilities and thereby achieve the best results they can, is presented. In the examples I shall describe I have played an instrumental role since it has become my belief that any job can always be done better provided that the people doing it can themselves become convinced that they can do better. Clearly there are many ideas on how to do this. The philosophy that I am presenting in this paper is based on my own experience, where I have both participated and observed it being applied; its effectiveness may be judged by the results. (author)

Drinking water quality and source reliability in rural Ashanti region, Ghana.

Science.gov (United States)

Arnold, Meghan; VanDerslice, James A; Taylor, Brooke; Benson, Scott; Allen, Sam; Johnson, Mark; Kiefer, Joe; Boakye, Isaac; Arhinn, Bernard; Crookston, Benjamin T; Ansong, Daniel

2013-03-01

Site-specific information about local water sources is an important part of a community-driven effort to improve environmental conditions. The purpose of this assessment was to gather this information for residents of rural villages in Ghana. Sanitary surveys and bacteriological testing for total coliforms and Escherichia coli (EC) using Colilert(®) were conducted at nearly 80 water sources serving eight villages. A focus group was carried out to assess the desirability and perceived quality of water sources. Standpipes accounted for almost half of the available water sources; however, a third of them were not functioning at the time of the survey. EC bacteria were found in the majority of shallow wells (80%), rivers (67%), and standpipes (61%), as well as 28% of dug wells. Boreholes were free of EC. Residents felt that the standpipes and boreholes produced safe drinking water. Intermittent service and poor water quality from the piped supply has led to limited access to drinking water. The perception of residents, that the water from standpipes is clean and does not need to be treated at home, is particularly troubling in light of the poor bacteriological quality of water from the standpipes.

Water Quality Assessment of River Soan (Pakistan) and Source Apportionment of Pollution Sources Through Receptor Modeling.

Science.gov (United States)

Nazeer, Summya; Ali, Zeshan; Malik, Riffat Naseem

2016-07-01

The present study was designed to determine the spatiotemporal patterns in water quality of River Soan using multivariate statistics. A total of 26 sites were surveyed along River Soan and its associated tributaries during pre- and post-monsoon seasons in 2008. Hierarchical agglomerative cluster analysis (HACA) classified sampling sites into three groups according to their degree of pollution, which ranged from least to high degradation of water quality. Discriminant function analysis (DFA) revealed that alkalinity, orthophosphates, nitrates, ammonia, salinity, and Cd were variables that significantly discriminate among three groups identified by HACA. Temporal trends as identified through DFA revealed that COD, DO, pH, Cu, Cd, and Cr could be attributed for major seasonal variations in water quality. PCA/FA identified six factors as potential sources of pollution of River Soan. Absolute principal component scores using multiple regression method (APCS-MLR) further explained the percent contribution from each source. Heavy metals were largely added through industrial activities (28 %) and sewage waste (28 %), nutrients through agriculture runoff (35 %) and sewage waste (28 %), organic pollution through sewage waste (27 %) and urban runoff (17 %) and macroelements through urban runoff (39 %), and mineralization and sewage waste (30 %). The present study showed that anthropogenic activities are the major source of variations in River Soan. In order to address the water quality issues, implementation of effective waste management measures are needed.

HVAC SYSTEMS AS EMISSION SOURCES AFFECTING INDOOR AIR QUALITY: A CRITICAL REVIEW

Science.gov (United States)

The paper discusses results of an evaluation of literature on heating, ventilating, and air-conditioning (HVAC) systems as contaminant emission sources that affect indoor air quality (IAQ). The various literature sources and methods for characterizing HVAC emission sources are re...

Improving benchmarking by using an explicit framework for the development of composite indicators: an example using pediatric quality of care

Science.gov (United States)

2010-01-01

Background The measurement of healthcare provider performance is becoming more widespread. Physicians have been guarded about performance measurement, in part because the methodology for comparative measurement of care quality is underdeveloped. Comprehensive quality improvement will require comprehensive measurement, implying the aggregation of multiple quality metrics into composite indicators. Objective To present a conceptual framework to develop comprehensive, robust, and transparent composite indicators of pediatric care quality, and to highlight aspects specific to quality measurement in children. Methods We reviewed the scientific literature on composite indicator development, health systems, and quality measurement in the pediatric healthcare setting. Frameworks were selected for explicitness and applicability to a hospital-based measurement system. Results We synthesized various frameworks into a comprehensive model for the development of composite indicators of quality of care. Among its key premises, the model proposes identifying structural, process, and outcome metrics for each of the Institute of Medicine's six domains of quality (safety, effectiveness, efficiency, patient-centeredness, timeliness, and equity) and presents a step-by-step framework for embedding the quality of care measurement model into composite indicator development. Conclusions The framework presented offers researchers an explicit path to composite indicator development. Without a scientifically robust and comprehensive approach to measurement of the quality of healthcare, performance measurement will ultimately fail to achieve its quality improvement goals. PMID:20181129

Land-based sources of pollution and environmental quality of Weija ...

African Journals Online (AJOL)

A survey of land-based sources of pollution was undertaken in the catchment area of Weija Lake. Activities that may influence the quality of the environment, and the sources, amounts and effects of the pollution of the water body were assessed. Water and precipitation chemistry showed that Na:Ca (0.48) and Na:K (2.0) ...

Effect of dietary protein source on piglet meat quality characteristics

Directory of Open Access Journals (Sweden)

Panagiotis E Simitzis

2014-03-01

Full Text Available An experiment was conducted to examine the effects of different dietary protein sources (soybean meal vs whey protein on piglet meat quality characteristics. Eighteen castrated male Large White × Duroc × Landrace piglets were randomly assigned to 2 groups. Piglets were kept in individual metabolic cages and fed ad libitum over a period of 38 days the following 2 diets: diet SB, which was formulated to meet the nutrient requirements of piglets using soybean meal as the main crude protein source and diet WP, where SB was totally replaced by a mixture of whey proteins on equal digestible energy and crude protein basis. At the end of the experiment, piglets were weighed and slaughtered. After overnight chilling, samples of Longissimus dorsi muscle were taken and were used for meat quality measurements.          No significant differences were observed in the values of pH, colour, water holding capacity, shear force and intramuscular fat content of L. dorsi muscle between the dietary treatments. Measurement of lipid oxidation values showed that dietary supplementation with different protein sources did not influence meat antioxidant properties during refrigerated storage. The SB piglets had lower 14:0 (P<0.01 and higher 18:3n-3 (P<0.001 levels in intramuscular fat in comparison with WP piglets. However, these changes were attributed to background differences in the dietary FA profile and not to a direct protein source effect. The results of this preliminary study indicate that the examined dietary protein sources (soybean meal or whey protein do not have a significant effect on meat quality characteristics of piglets.

Marine sources influence fog bioaerosol composition in Namibia and Maine

Science.gov (United States)

Evans, S. E.; Dueker, E.; Logan, J. R. V.; Weathers, K. C.

2017-12-01

Organic aerosol particles act as condensation nuclei for fogs and clouds (CCN) and are main determinants of fog evolution, chemical processing, and overall aerosol-fog-cloud interactions. Recent work has confirmed the presence of marine bioaerosols, but little is known about their sources, transport, taxonomic diversity or viability. The few studies that have characterized bioaerosols in fog have been limited to culture-based approaches that capture only a fraction of microbial diversity. We characterized fungal and bacterial communities in the fog in two iconic fog systems, the Coast of Maine (USA) and the Namib Desert (Namibia). The biology of fog in both systems was diverse and distinct, by geography, from dry aerosols, and from local sources. The local environment had a dominant influence on fog in both the Namib and Maine; in particular, the biology of fog in Maine, which was collected near the coast, was more similar to microbial communities from the ocean surface. In both systems, differences between pre- and post-fog aerosol communities suggest that fog events can significantly alter microbial aerosol diversity and composition. This insight into the microbial composition of fog indicates that its origin and frequency has the potential to influence the number and diversity of microorganisms that settle in a given environment, and the composition of microbial aerosol communities in ambient or clear conditions. Here we suggest that fog microbes can possess specific traits that enhance nucleation, altering the transport and deposition of marine- and soil-derived organic matter in terrestrial systems.

Characterizing the oxygen isotopic composition of phosphate sources to aquatic ecosystems

Science.gov (United States)

Young, M.B.; McLaughlin, K.; Kendall, C.; Stringfellow, W.; Rollog, M.; Elsbury, K.; Donald, E.; Paytan, A.

2009-01-01

The oxygen isotopic composition of dissolved inorganic phosphate (δ18Op) in many aquatic ecosystems is not in isotopic equilibrium with ambient water and, therefore, may reflect the source δ18Op. Identification of phosphate sources to water bodies is critical for designing best management practices for phosphate load reduction to control eutrophication. In order for δ18O p to be a useful tool for source tracking, the δ18Op of phosphate sources must be distinguishable from one another; however, the δ18Op of potential sources has not been well characterized. We measured the δ18O p of a variety of known phosphate sources, including fertilizers, semiprocessed phosphorite ore, particulate aerosols, detergents, leachates of vegetation, soil, animal feces, and wastewater treatment plant effluent. We found a considerable range of δ18Op values (from +8.4 to +24.9‰) for the various sources, and statistically significant differences were found between several of the source types. δ18Op measured in three different fresh water systems was generally not in equilibrium with ambient water. Although there is overlap in δ18Op values among the groups of samples, our results indicate that some sources are isotopically distinct and δ18Op can be used for identifying phosphate sources to aquatic systems.

Effect of legume grains as a source of dietary protein on the quality of organic lamb meat.

Science.gov (United States)

Bonanno, Adriana; Tornambè, Gabriele; Di Grigoli, Antonino; Genna, Vincenzo; Bellina, Vincenzo; Di Miceli, Giuseppe; Giambalvo, Dario

2012-11-01

This study evaluated the effects on lamb growth, carcass traits and meat quality of replacing conventional soybean meal in the diet with alternative legume grains. Twenty-eight male lambs of Comisana breed weighing 16.9 ± 2.7 kg at weaning (66 ± 6 days old) were assigned to one of four diets. Until slaughter at 129 ± 6 days of age, each group received ad libitum pelleted alfalfa hay and concentrates differing in the source of protein: chickpea, faba bean, pea or soybean meal. Lambs fed chickpea showed higher dry matter and protein intakes from concentrate than those fed soybean. Lambs' growth, carcass weight and net dressing percentage did not vary by protein source, although chickpea lambs had more perirenal and pelvic fat than those in the soybean group. Diet did not affect chemical composition, colour, thawing and cooking losses, tenderness, and sensory properties of meat. Chickpea increased trans-vaccenic and linoleic acid, and chickpea and faba bean increased the isomers of conjugated linoleic acid. Legume grains can completely replace soybean meal in concentrate, resulting in lamb carcasses and meat of comparable quality. Chickpea leads to an increase in feed intake of lambs and in fat depots in the carcass, and a more beneficial fatty acid profile. Copyright © 2012 Society of Chemical Industry.

Local sources of pollution and their impacts in Alaska (Invited)

Science.gov (United States)

Molders, N.

2013-12-01

The movie 'Into the Wilde' evoke the impression of the last frontier in a great wide and pristine land. With over half a million people living in Alaska an area as larger as the distance from the US West to the East Coast, this idea comes naturally. The three major cities are the main emission source in an otherwise relative clean atmosphere. On the North Slope oil drilling and production is the main anthropogenic emission sources. Along Alaska's coasts ship traffic including cruises is another anthropogenic emission source that is expected to increase as sea-ice recedes. In summer, wildfires in Alaska, Canada and/or Siberia may cause poor air quality. In winter inversions may lead poor air quality and in spring. In spring, aged polluted air is often advected into Alaska. These different emission sources yield quite different atmospheric composition and air quality impacts. While this may make understanding Alaska's atmospheric composition at-large a challenging task, it also provides great opportunities to examine impacts without co-founders. The talk will give a review of the performed research, and insight into the challenges.

Assessment of the microbial quality of river water sources in rural ...

African Journals Online (AJOL)

drinie

2002-07-03

Jul 3, 2002 ... Assessment of the microbial quality of river water sources ... These untreated water sources are used for drinking and domestic purposes and pose a serious threat to ... These diseases cause crippling, devastating and debilitating effects ..... gastrointestinal illness, due mainly by enteric viruses in sewage.

Fire Influences on Atmospheric Composition, Air Quality, and Climate

Science.gov (United States)

Voulgarakis, Apostolos; Field, Robert D.

2015-01-01

Fires impact atmospheric composition through their emissions, which range from long-lived gases to short-lived gases and aerosols. Effects are typically larger in the tropics and boreal regions but can also be substantial in highly populated areas in the northern mid-latitudes. In all regions, fire can impact air quality and health. Similarly, its effect on large-scale atmospheric processes, including regional and global atmospheric chemistry and climate forcing, can be substantial, but this remains largely unexplored. The impacts are primarily realised in the boundary layer and lower free troposphere but can also be noticeable in upper troposphere/lower stratosphere (UT/LS) region, for the most intense fires. In this review, we summarise the recent literature on findings related to fire impact on atmospheric composition, air quality and climate. We explore both observational and modelling approaches and present information on key regions and on the globe as a whole. We also discuss the current and future directions in this area of research, focusing on the major advances in emission estimates, the emerging efforts to include fire as a component in Earth system modelling and the use of modelling to assess health impacts of fire emissions.

Functional High-Intensity Circuit Training Improves Body Composition, Peak Oxygen Uptake, Strength, and Alters Certain Dimensions of Quality of Life in Overweight Women

OpenAIRE

Sperlich, Billy; Wallmann-Sperlich, Birgit; Zinner, Christoph; Von Stauffenberg, Valerie; Losert, Helena; Holmberg, Hans-Christer

2017-01-01

Source at https://doi.org/10.3389/fphys.2017.00172 The effects of circuit-like functional high-intensity training (CircuitHIIT) alone or in combination with high-volume low-intensity exercise (Circuitcombined) on selected cardio-respiratory and metabolic parameters, body composition, functional strength and the quality of life of overweight women were compared. In this single-center, two-armed randomized, controlled study, overweight women performed 9-weeks (3 sessions·wk−1) of either Ci...

A Critical Assessment of the Quality and Validity of Composite Indicators of Innovation

Energy Technology Data Exchange (ETDEWEB)

Vértesy, D.

2016-07-01

While it is generally accepted that monitoring innovation system performance requires a set of indicators, there is a constant debate on whether and how composite indices can be used to summarize them. This paper enters this discussion by assessing the validity and quality of the most commonly used composite indicators of innovation. In our framework, the validity of an index relates to the link between component indicators or aggregates and to the aspect(s) of national systems of innovation they seek to measure, while the quality of an indicator relates to its statistical properties. To better understand validity, we discuss how the evolution of the national system of innovation concept and its use in policy has shifted demand from an advocacy to more analytical functions of composite indicators of innovation.We next examine selected composite indicators of innovation (the WIPO-INSEAD’s Global Innovation Indicator, the Summary Innovation Index and Innovation Output Indicator of the European Commission and the Fraunhofer Innovation Index) in different contexts of external and internal validity and conduct global sensitivity analyses on them. Our policy-relevant findings highlight the need for analytically stronger composites of a more limited set of indicators.We also found significant quality differences across the indices, as some included components which explain little or none of the variance in composite scores, and were more sensitive to modeling choices. The indices studied differed in how validly they represented various innovation system functions and types of innovation, and showed information relevant for a broader or a more limited set of stakeholders. We argue that further development of innovation indicators should put more emphasis on identifying tradeoffs within innovation policy, and unintended consequences of innovative activities. (Author)

Determination of the power of multielement aerosol composition emission from distant industrial sources

International Nuclear Information System (INIS)

Popova, S.A.; Kutsenogij, K.P.; Chankina, O.V.

2008-01-01

The results from the monitoring of the temporal variability of the multielement composition of atmospheric aerosols are presented. They are used to determine the emission power of a series of elements from distant sources.

40 CFR 63.5795 - How do I know if my reinforced plastic composites production facility is a new affected source or...

Science.gov (United States)

2010-07-01

... for Hazardous Air Pollutants: Reinforced Plastic Composites Production What This Subpart Covers § 63.5795 How do I know if my reinforced plastic composites production facility is a new affected source or an existing affected source? (a) A reinforced plastic composites production facility is a new...

Sources and composition of submicron organic mass in marine aerosol particles

Science.gov (United States)

Frossard, Amanda A.; Russell, Lynn M.; Burrows, Susannah M.; Elliott, Scott M.; Bates, Timothy S.; Quinn, Patricia K.

2014-11-01

The sources and composition of atmospheric marine aerosol particles (aMA) have been investigated with a range of physical and chemical measurements from open-ocean research cruises. This study uses the characteristic functional group composition (from Fourier transform infrared spectroscopy) of aMA from five ocean regions to show the following: (i) The organic functional group composition of aMA that can be identified as mainly atmospheric primary marine (ocean derived) aerosol particles (aPMA) is 65 ± 12% hydroxyl, 21 ± 9% alkane, 6 ± 6% amine, and 7 ± 8% carboxylic acid functional groups. Contributions from photochemical reactions add carboxylic acid groups (15%-25%), shipping effluent in seawater and ship emissions add additional alkane groups (up to 70%), and coastal or continental emissions mix in alkane and carboxylic acid groups. (ii) The organic composition of aPMA is nearly identical to model-generated primary marine aerosol particles from bubbled seawater (gPMA, which has 55 ± 14% hydroxyl, 32 ± 14% alkane, and 13 ± 3% amine functional groups), indicating that its overall functional group composition is the direct consequence of the organic constituents of the seawater source. (iii) While the seawater organic functional group composition was nearly invariant across all three ocean regions studied and the ratio of organic carbon to sodium (OC/Na+) in the gPMA remained nearly constant over a broad range of chlorophyll a concentrations, the gPMA alkane group fraction appeared to increase with chlorophyll a concentrations (r = 0.66). gPMA from productive seawater had a larger fraction of alkane functional groups (42 ± 9%) compared to gPMA from nonproductive seawater (22 ± 10%), perhaps due to the presence of surfactants in productive seawater that stabilize the bubble film and lead to preferential drainage of the more soluble (lower alkane group fraction) organic components. gPMA has a hydroxyl group absorption peak location characteristic of

Source apportionment of PM2.5 in North India using source-oriented air quality models

International Nuclear Information System (INIS)

Guo, Hao; Kota, Sri Harsha; Sahu, Shovan Kumar; Hu, Jianlin; Ying, Qi; Gao, Aifang; Zhang, Hongliang

2017-01-01

In recent years, severe pollution events were observed frequently in India especially at its capital, New Delhi. However, limited studies have been conducted to understand the sources to high pollutant concentrations for designing effective control strategies. In this work, source-oriented versions of the Community Multi-scale Air Quality (CMAQ) model with Emissions Database for Global Atmospheric Research (EDGAR) were applied to quantify the contributions of eight source types (energy, industry, residential, on-road, off-road, agriculture, open burning and dust) to fine particulate matter (PM 2.5 ) and its components including primary PM (PPM) and secondary inorganic aerosol (SIA) i.e. sulfate, nitrate and ammonium ions, in Delhi and three surrounding cities, Chandigarh, Lucknow and Jaipur in 2015. PPM mass is dominated by industry and residential activities (>60%). Energy (∼39%) and industry (∼45%) sectors contribute significantly to PPM at south of Delhi, which reach a maximum of 200 μg/m 3 during winter. Unlike PPM, SIA concentrations from different sources are more heterogeneous. High SIA concentrations (∼25 μg/m 3 ) at south Delhi and central Uttar Pradesh were mainly attributed to energy, industry and residential sectors. Agriculture is more important for SIA than PPM and contributions of on-road and open burning to SIA are also higher than to PPM. Residential sector contributes highest to total PM 2.5 (∼80 μg/m 3 ), followed by industry (∼70 μg/m 3 ) in North India. Energy and agriculture contribute ∼25 μg/m 3 and ∼16 μg/m 3 to total PM 2.5 , while SOA contributes <5 μg/m 3 . In Delhi, industry and residential activities contribute to 80% of total PM 2.5 . - Highlights: • Sources of PM 2.5 in North India were quantified by source-oriented CMAQ. • Industrial/residential activities are the dominating sources (60–70%) for PPM. • Energy/agriculture are the most important sources (30–40%) for SIA. • Strong seasonal

Source position error influence on industry CT image quality

International Nuclear Information System (INIS)

Cong Peng; Li Zhipeng; Wu Haifeng

2004-01-01

Based on the emulational exercise, the influence of source position error on industry CT (ICT) image quality was studied and the valuable parameters were obtained for the design of ICT. The vivid container CT image was also acquired from the CT testing system. (authors)

DNA Source Selection for Downstream Applications Based on DNA Quality Indicators Analysis

Science.gov (United States)

Lucena-Aguilar, Gema; Sánchez-López, Ana María; Barberán-Aceituno, Cristina; Carrillo-Ávila, José Antonio; López-Guerrero, José Antonio

2016-01-01

High-quality human DNA samples and associated information of individuals are necessary for biomedical research. Biobanks act as a support infrastructure for the scientific community by providing a large number of high-quality biological samples for specific downstream applications. For this purpose, biobank methods for sample preparation must ensure the usefulness and long-term functionality of the products obtained. Quality indicators are the tool to measure these parameters, the purity and integrity determination being those specifically used for DNA. This study analyzes the quality indicators in DNA samples derived from 118 frozen human tissues in optimal cutting temperature (OCT) reactive, 68 formalin-fixed paraffin-embedded (FFPE) tissues, 119 frozen blood samples, and 26 saliva samples. The results obtained for DNA quality are discussed in association with the usefulness for downstream applications and availability of the DNA source in the target study. In brief, if any material is valid, blood is the most approachable option of prospective collection of samples providing high-quality DNA. However, if diseased tissue is a requisite or samples are available, the recommended source of DNA would be frozen tissue. These conclusions will determine the best source of DNA, according to the planned downstream application. Furthermore our results support the conclusion that a complete procedure of DNA quantification and qualification is necessary to guarantee the appropriate management of the samples, avoiding low confidence results, high costs, and a waste of samples. PMID:27158753

Clinical Practice and Quality Assurance Challenges in Modern Brachytherapy Sources and Dosimetry

International Nuclear Information System (INIS)

Butler, Wayne M.; Merrick, Gregory S.

2008-01-01

Modern brachytherapy has led to effective treatments through the establishment of broadly applicable dosimetric thresholds for maximizing survival with minimal morbidity. Proper implementation of recent dosimetric consensus statements and quality assurance procedures is necessary to maintain the established level of safety and efficacy. This review classifies issues as either 'systematic' or 'stochastic' in terms of their impact on large groups or individual patients, respectively. Systematic changes affecting large numbers of patients occur infrequently and include changes in source dosimetric parameters, prescribing practice, dose calculation formalism, and improvements in calculation algorithms. The physicist must be aware of how incipient changes accord with previous experience. Stochastic issues involve procedures that are applied to each patient individually. Although ample guidance for quality assurance of brachytherapy sources exists, some ambiguities remain. The latest American Association of Physicists in Medicine guidance clarifies what is meant by independent assay, changes source sampling recommendations, particularly for sources in sterile strands and sterile preassembled needles, and modifies action level thresholds. The changing environment of brachytherapy has not changed the fact that the prime responsibility for quality assurance in brachytherapy lies with the institutional medical physicist

POLLUTION SOURCES AND WATER QUALITY STATE OF THE SUPRAŚL RIVER

Directory of Open Access Journals (Sweden)

Mirosław Skorbiłowicz

2016-04-01

Full Text Available The main purpose of the study was to evaluate water quality of the Supraśl river and identify its main pollution sources. On the river and its tributaries, 8 control points were selected, located near Krynica, Gródek, Nowosiółki, Zasady (mouth of the tributary Sokołda, Supraśl, Nowodworce, Dobrzyniewo (mouth of the tributary Biała and Dzikie. The control points were selected in such a way as to take into account the impact of major point sources of analyzed components located along the river and its main tributaries on water quality in the main stream catchment. Water samples were collected once a month during the period from May to November in 2014. In water samples the concentration of dissolved oxygen, Cl-, SO42-, N-NH4+, P-PO43- and the values of pH, BOD5 and electrolytic conductivity were indicated. Based on the obtained results, loads of the individual components in river waters were calculated as a product of concentration and Supraśl waters flow rate in a particular month. Supraśl waters, due to values of most analyzed parameters, should be classified as first quality class. The source of Cl-, SO42-, N-NH4+ in Supraśl waters were treated wastewater and other anthropogenic sources associated with the basin development. Reduced Supraśl water quality is caused by the inflow of organic substances expressed by BZT5 from natural and anthropogenic origin and concentration of PO43-, which were mainly delivered with treated wastewater.

Source apportionment and air quality impact assessment studies in Beijing/China

Science.gov (United States)

Suppan, P.; Schrader, S.; Shen, R.; Ling, H.; Schäfer, K.; Norra, S.; Vogel, B.; Wang, Y.

2012-04-01

More than 15 million people in the greater area of Beijing are still suffering from severe air pollution levels caused by sources within the city itself but also from external impacts like severe dust storms and long range advection from the southern and central part of China. Within this context particulate matter (PM) is the major air pollutant in the greater area of Beijing (Garland et al., 2009). PM did not serve only as lead substance for air quality levels and therefore for adverse health impact effects but also for a strong influence on the climate system by changing e.g. the radiative balance. Investigations on emission reductions during the Olympic Summer Games in 2008 have caused a strong reduction on coarser particles (PM10) but not on smaller particles (PM2.5). In order to discriminate the composition of the particulate matter levels, the different behavior of coarser and smaller particles investigations on source attribution, particle characteristics and external impacts on the PM levels of the city of Beijing by measurements and modeling are performed: Examples of long term measurements of PM2.5 filter sampling in 2005 with the objectives of detailed chemical (source attribution, carbon fraction, organic speciation and inorganic composition) and isotopic analyses as well as toxicological assessment in cooperation with several institutions (Karlsruhe Institute of Technology (IfGG/IMG), Helmholtz Zentrum München (HMGU), University Rostock (UR), Chinese University of Mining and Technology Beijing, CUMTB) will be discussed. Further experimental studies include the operation of remote sensing systems to determine continuously the MLH (by a ceilometer) and gaseous air pollutants near the ground (by DOAS systems) as well as at the 320 m measurement tower (adhesive plates at different heights for passive particle collection) in cooperation with the Institute of Atmospheric Physics (IAP) of the Chinese Academy of Sciences (CAS). The influence of the MLH on

Composition, sources, and bioavailability of nitrogen in a longitudinal gradient from freshwater to estuarine waters.

Science.gov (United States)

Jani, Jariani; Toor, Gurpal S

2018-06-15

Nitrogen (N) transport from land to water is a dominant contributor of N in estuarine waters leading to eutrophication, harmful algal blooms, and hypoxia. Our objectives were to (1) investigate the composition of inorganic and organic N forms, (2) distinguish the sources and biogeochemical mechanisms of nitrate-N (NO 3 -N) transport using stable isotopes of NO 3 - and Bayesian mixing model, and (3) determine the dissolved organic N (DON) bioavailability using bioassays in a longitudinal gradient from freshwater to estuarine ecosystem located in the Tampa Bay, Florida, United States. We found that DON was the most dominant N form (mean: 64%, range: 46-83%) followed by particulate organic N (PON, mean: 22%, range: 14-37%), whereas inorganic N forms (NO x -N: 7%, NH 4 -N: 7%) were 14% of total N in freshwater and estuarine waters. Stable isotope data of NO 3 - revealed that nitrification was the main contributor (36.4%), followed by soil and organic N sources (25.5%), NO 3 - fertilizers (22.4%), and NH 4 + fertilizers (15.7%). Bioassays showed that 14 to 65% of DON concentrations decreased after 5-days of incubation indicating utilization of DON by microbes in freshwater and estuarine waters. These results suggest that despite low proportion of inorganic N forms, the higher concentrations and bioavailability of DON can be a potential source of N for algae and bacteria leading to water quality degradation in the estuarine waters. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effect of dietary starch source on milk production and composition of ...

African Journals Online (AJOL)

The objective of this study was to evaluate the effects of four sources of starch on milk production and composition, nutrient digestion and blood metabolites of lactating Holstein cows. Four multiparous Holstein cows (708 ± 70 kg of body weight; 83 ± 9 days in milk) were used in a 4 × 4 Latin square design with 21-d periods.

Effect of the glandular composition on digital breast tomosynthesis image quality and dose optimisation

International Nuclear Information System (INIS)

Marques, T.; Di Maria, S.; Vaz, P.; Ribeiro, A.; Belchior, A.; Cardoso, J.; Matela, N.; Oliveira, N.; Almeida, P.; Janeiro, L.

2015-01-01

In the image quality assessment for digital breast tomosynthesis (DBT), a breast phantom with an average percentage of 50 % glandular tissue is seldom used, which may not be representative of the breast tissue composition of the women undergoing such examination. This work aims at studying the effect of the glandular composition of the breast on the image quality taking into consideration different sizes of lesions. Monte Carlo simulations were performed using the state-of-the-art computer program PENELOPE to validate the image acquisition system of the DBT equipment as well as to calculate the mean glandular dose for each projection image and for different breast compositions. The integrated PENELOPE imaging tool (PenEasy) was used to calculate, in mammography, for each clinical detection task the X-ray energy that maximises the figure of merit. All the 2D cranial-caudal projections for DBT were simulated and then underwent the reconstruction process applying the Simultaneous Algebraic Reconstruction Technique. Finally, through signal-to-noise ratio analysis, the image quality in DBT was assessed. (authors)

[Research on stormwater runoff quality of mountain city by source area monitoring].

Science.gov (United States)

Li, Li-Qing; Shan, Bao-Qing; Zhao, Jian-Wei; Guo, Shu-Gang; Gao, Yong

2012-10-01

Stormwater runoff samples were collected from 10 source areas in Mountain City, Chongqing, during five rain events in an attempt to investigate the characteristics of runoff quality and influencing factors. The outcomes are expected to offer practical guidance of sources control of urban runoff pollution. The results indicated that the stormwater runoff of Mountain City presented a strong first flush for almost all events and constituents. The runoff quality indices were also influenced by the rainfall intensity. The concentration of TSS, COD, TN and TP decreased as the rainfall intensity increased. The concentrations of COD and TP in stormwater runoff were highly correlated with TSS concentrations. Suspended solid matter were not only the main pollutant of stormwater runoff but also served as the vehicle for transport of organic matter and phosphorus. Organic matter and phosphorus in stormwatrer runoff were mainly bound to particles, whereas nitrogen was predominantly dissolved, with ammonia and nitrate. A significant difference of stormwater runoff quality was observed among the ten monitored source areas. The highest magnitude of urban stormwater runoff pollution was expected in the commercial area and the first trunk road, followed by the minor road, residential area, parking lot and roof. Urban surface function, traffic volume, population density, and street sweeping practice are the main factors determining spatial differentiation of urban surface runoff quality. Commercial area, the first trunk road and residential area with high population density are the critical sources areas of urban stormwater runoff pollution.

Fillet proximate composition, lipid quality, yields, and organoleptic quality of Mediterranean-farmed marine fish: A review with emphasis on new species.

Science.gov (United States)

Grigorakis, Kriton

2017-09-22

Species diversification in Mediterranean mariculture involves various important fish that contribute to the diet of many human populations. These include meagres (Sciaenidae), flatfishes, mullets, and various sparids. Their quality aspects (yields, fillet proximate composition, and lipid quality) are discussed in this review. Their filleting yield is mostly 40-45%. The viscerosomatic index ranges from 1.5% to 14%, depending on species. Low muscle fat contents of flatfishes and meagres differentiate them from the rest of the farmed species. Farmed fish contain high n-3 polyunsaturates fatty acids (PUFA; 12.3-36.3% vs. 5.48-37.2% in the wild) and have higher muscle fat and n-6 PUFA contents (mainly 18:2 n-6) than their wild counterparts. The aquaculture management, diet, and season can affect fillet composition and fatty acids, while season (i.e. food availability and maturation) largely affects lipid quality in wild fish. Data on the sensory quality of Mediterranean-farmed species are mainly limited to whether specific management differentiates the sensory quality; thus, further development of tools for sensory analysis is required. Observations on the quality features in farmed Mediterranean fish indicate that species diversification can also provide product diversification based on different commercial weights and fillet quality specifications.

Chemical composition and sources of organic aerosols over London from the ClearfLo 2012 campaigns

Science.gov (United States)

Finessi, Emanuela; Holmes, Rachel; Hopkins, James; Lee, James; Harrison, Roy; Hamilton, Jacqueline

2014-05-01

Air quality in urban areas represents a major public health issue with around one third of the European population concentrated in cities and numbers expected to increase at global scale, particularly in developing countries. Particulate matter (PM) represents a primary threat for human health as numerous studies have confirmed the association between increased levels of cardiovascular and respiratory diseases with the exposure to PM. Despite considerable efforts made in improving air quality and progressively stricter emissions regulations, the PM concentrations have not changed much over the past decades for reasons that remain unclear, and highlight that studies on PM source apportionment are required for the formulation of effective policy. We investigated the chemical composition of organic aerosol (OA) collected during two intensive field campaigns held in winter and summer 2012 in the frame of the project Clean air for London (http://www.clearflo.ac.uk/). PM samples were collected both at a city background site (North Kensington) and at a rural site 50 km southeast of London (Detling) with 8 to 24 hours sampling schedule and analysed using off-line methods. Thermal-optical analysis was used to quantify OC-EC components while a suite of soft ionization mass spectrometric techniques was deployed for detailed chemical characterization. Liquid chromatography mass Spectrometry (LC-MSn) was mostly used for the simultaneous detection and quantification of various tracers for both primary and secondary OA sources. Well-established markers for wood burning primary OA like levoglucosan and azelaic acid were quantified together with various classes of nitroaromatics including methyl-nitrocatechols that are potential tracers for wood burning secondary OA. In addition, oxidation products of biogenic VOCs such as isoprene and monoterpenes were also quantified for both seasons and sites. A non-negligible contribution from biogenic SOA to urban OA was found in summertime

Drinking water sources, availability, quality, access and utilization for goats in the Karak Governorate, Jordan.

Science.gov (United States)

Al-Khaza'leh, Ja'far Mansur; Reiber, Christoph; Al Baqain, Raid; Valle Zárate, Anne

2015-01-01

Goat production is an important agricultural activity in Jordan. The country is one of the poorest countries in the world in terms of water scarcity. Provision of sufficient quantity of good quality drinking water is important for goats to maintain feed intake and production. This study aimed to evaluate the seasonal availability and quality of goats' drinking water sources, accessibility, and utilization in different zones in the Karak Governorate in southern Jordan. Data collection methods comprised interviews with purposively selected farmers and quality assessment of water sources. The provision of drinking water was considered as one of the major constraints for goat production, particularly during the dry season (DS). Long travel distances to the water sources, waiting time at watering points, and high fuel and labor costs were the key reasons associated with the problem. All the values of water quality (WQ) parameters were within acceptable limits of the guidelines for livestock drinking WQ with exception of iron, which showed slightly elevated concentration in one borehole source in the DS. These findings show that water shortage is an important problem leading to consequences for goat keepers. To alleviate the water shortage constraint and in view of the depleted groundwater sources, alternative water sources at reasonable distance have to be tapped and monitored for water quality and more efficient use of rainwater harvesting systems in the study area is recommended.

Effects of dietary oil sources on egg quality, fatty acid composition of ...

African Journals Online (AJOL)

The results of this study demonstrated that olive oil improved egg weight and egg shell quality compared to the other oils tested; fish and soyabean oil increased the omega-3 fatty acid level of egg yolk, and soyabean oil had positive effects on serum lipid concentrations. Incorporation of these oils into the diets of Japanese ...

Nutrient composition and technological quality of meat from alpacas reared in Peru.

Science.gov (United States)

Salvá, Bettit K; Zumalacárregui, José M; Figueira, Ana C; Osorio, María T; Mateo, Javier

2009-08-01

The aim of this study was to increase the knowledge on alpaca meat quality characteristics. Twenty Huacaya breed alpacas, reared under a traditional unspecialized production system at the Andean region of Peru, were slaughtered at ages between 18 and 24months. Analyses were carried out on Longissimus thoracis and lumborum muscle (LTLM), unless otherwise specified. These included composition parameters: moisture, fat, protein, ash, minerals, amino acids, fatty acid profile (of both LTLM and perirenal fat), retinol and tocopherol concentrations and myoglobin and collagen contents. Other meat quality parameters were evaluated: pH, colour, water holding capacity and Warner-Bratzler shear-force. Alpaca LTLM was characterized by a low intramuscular fat content and mineral and amino acid compositions, polyunsaturated to saturated fatty acids ratio and conjugated linoleic acid content comparable to those found for beef and sheep meat. However, specifically, alpaca meat showed a relatively high n-6 to n-3 (3.7) ratio and low vitamin E concentration. Values of alpaca meat technological quality parameters were in the ranges reported for more conventional red meats, the exception being a lower b(∗) value.

Metabolic routing of dietary nutrients in birds: effects of diet quality and macronutrient composition revealed using stable isotopes.

Science.gov (United States)

Podlesak, David W; McWilliams, Scott R

2006-01-01

During fall migration many songbirds switch from consuming primarily insects to consuming mostly fruit. Fruits with more carbohydrates and less protein may be sufficient to rebuild expended fat stores, but such fruits may be inadequate to replace catabolized protein. We manipulated the concentrations and isotopic signatures of macronutrients in diets fed to birds to study the effects of diet quality on metabolic routing of dietary nutrients. We estimated that approximately 45% and 75%, respectively, of the carbon in proteinaceous tissue of birds switched to high- or low-protein diets came from nonprotein dietary sources. In contrast, we estimated that approximately 100% and 20%-80%, respectively, of the nitrogen in proteinaceous tissues of birds switched to high- or low-protein diets was attributable to dietary protein. Thus, the routing and assimilation of dietary carbon and nitrogen differed depending on diet composition. As a result, delta (15)N of tissues collected from wild animals that consume high-quality diets may reliably indicate the dietary protein source, whereas delta (13)C of these same tissues is likely the product of metabolic routing of carbon from several macronutrients. These results have implications for how isotopic discrimination is best estimated and how we can study macronutrient routing in wild animals.

Quality control and in-service inspection technology for hybrid-composite girder bridges.

Science.gov (United States)

2014-08-01

This report describes efforts to develop quality control tools and in-service inspection technologies for the fabrication and construction of Hybrid Composite Beams (HCBs). HCBs are a new bridge technology currently being evaluated by the Missouri De...

Studies of the contributions of nonpoint terrestrial sources to mineral water quality

International Nuclear Information System (INIS)

Huff, D.D.

1977-05-01

The contributions of nonpoint sources of water quality constituents represent a background loading rate that will not be reduced easily. Consequently, those contributions may have a dominant effect on aquatic ecosystems once point sources have been controlled. Modeling studies conducted at the Tennessee Valley Authority and Oak Ridge National Laboratory represent contrasting approaches that highlight some of the possibilities for predicting nonpoint source inputs to aquatic systems

HONO and Inorganic Fine Particle Composition in Typical Monsoon Region with Intensive Anthropogenic Emission: In-situ Observations and Source Identification.

Science.gov (United States)

Xie, Y.; Nie, W.; Ding, A.; Huang, X.

2015-12-01

Yangtze River Delta (YRD) is one of the most typical monsoon area with probably the most largest population intensity in the world. With sharply economic development and the large anthropogenic emissions, fine particle pollution have been one of the major air quality problem and may further have impact on the climate system. Though a lot of control policy (sulfur emission have been decreasing from 2007) have been conducted in the region, studies showed the sulfate in fine particles still take major fraction as the nitrate from nitrogen oxides increased significantly. In this study, the role of inorganic chemical compositions in fine particles was investigated with two years in-situ observation. Sulfate and Nitrate contribute to fine particle mass equally in general, but sulfate contributes more during summer and nitrate played more important role in winter. Using lagrangian dispersion backward modeling and source contribution clustering method, the impact of airmass coming from different source region (industrial, dust, biogenic emissions, etc) on fine particle inorganic compositions were discussed. Furthermore, we found two unique cases showing in-situ implications for sulfate formation by nitrogen dioxide oxidation mechanisms. It was showed that the mixing of anthropogenic pollutants with long-range transported mineral dust and biomass burning plume would enhance the sulfate formation by different chemistry mechanisms. This study focus on the complex aspects of fine particle formation in airmasses from different source regions: . It highlights the effect of NOx in enhancing the atmospheric oxidization capacity and indicates a potentially very important impact of increasing NOx on air pollution formation and regional climate change in East Asia.

Complex EUV imaging reflectometry: spatially resolved 3D composition determination and dopant profiling with a tabletop 13nm source

Science.gov (United States)

Porter, Christina L.; Tanksalvala, Michael; Gerrity, Michael; Miley, Galen P.; Esashi, Yuka; Horiguchi, Naoto; Zhang, Xiaoshi; Bevis, Charles S.; Karl, Robert; Johnsen, Peter; Adams, Daniel E.; Kapteyn, Henry C.; Murnane, Margaret M.

2018-03-01

With increasingly 3D devices becoming the norm, there is a growing need in the semiconductor industry and in materials science for high spatial resolution, non-destructive metrology techniques capable of determining depth-dependent composition information on devices. We present a solution to this problem using ptychographic coherent diffractive imaging (CDI) implemented using a commercially available, tabletop 13 nm source. We present the design, simulations, and preliminary results from our new complex EUV imaging reflectometer, which uses coherent 13 nm light produced by tabletop high harmonic generation. This tool is capable of determining spatially-resolved composition vs. depth profiles for samples by recording ptychographic images at multiple incidence angles. By harnessing phase measurements, we can locally and nondestructively determine quantities such as device and thin film layer thicknesses, surface roughness, interface quality, and dopant concentration profiles. Using this advanced imaging reflectometer, we can quantitatively characterize materials-sciencerelevant and industry-relevant nanostructures for a wide variety of applications, spanning from defect and overlay metrology to the development and optimization of nano-enhanced thermoelectric or spintronic devices.

Software Quality in the Trenches: Two Case Studies of Quality Assurance Practices in Free/Libre and Open Source Software (FLOSS)

OpenAIRE

Vestbø, Tor Arne

2007-01-01

When proponents of open source software are asked to explain the success of their movement they typically point to the quality of the software produced, which is in turn attributed to the rather unconventional development model of releasing unfinished versions of the software and having users look over the code and report and fix bugs. This thesis investigates the open source quality assurance model from a knowledge management perspective based on the assumption that debugging involves a h...

Identifying individual changes in performance with composite quality indicators while accounting for regression to the mean.

Science.gov (United States)

Gajewski, Byron J; Dunton, Nancy

2013-04-01

Almost a decade ago Morton and Torgerson indicated that perceived medical benefits could be due to "regression to the mean." Despite this caution, the regression to the mean "effects on the identification of changes in institutional performance do not seem to have been considered previously in any depth" (Jones and Spiegelhalter). As a response, Jones and Spiegelhalter provide a methodology to adjust for regression to the mean when modeling recent changes in institutional performance for one-variable quality indicators. Therefore, in our view, Jones and Spiegelhalter provide a breakthrough methodology for performance measures. At the same time, in the interests of parsimony, it is useful to aggregate individual quality indicators into a composite score. Our question is, can we develop and demonstrate a methodology that extends the "regression to the mean" literature to allow for composite quality indicators? Using a latent variable modeling approach, we extend the methodology to the composite indicator case. We demonstrate the approach on 4 indicators collected by the National Database of Nursing Quality Indicators. A simulation study further demonstrates its "proof of concept."

Diet composition, quality and overlap of sympatric American pronghorn and gemsbok

Science.gov (United States)

Cain, James W.; Avery, Mindi M.; Caldwell, Colleen A.; Abbott, Laurie B.; Holechek, Jerry L.

2017-01-01

Species with a long evolutionary history of sympatry often have mechanisms for resource partitioning that reduce competition. However, introduced non-native ungulates often compete with native ungulates and competitive effects can be exacerbated in arid regions due to low primary productivity. Our objectives were to characterize diet composition, quality, and overlap between American pronghorn Antilocapra americana and introduced non-native gemsbok Oryx gazella in southcentral New Mexico, USA. Severe drought occurred between 2010 and 2011, which allowed us to evaluate drought impacts on diet composition, quality, and overlap. Using feces collected from each species, we assessed diet composition and overlap with microhistological analysis and diet quality using fecal nitrogen (FN) and fecal 2,6-diaminopimelic acid (FDAPA). Pronghorn diet was primarily composed of shrubs in the cool—dry season (64.5%) then shifted to forbs in the warm—dry (64.7%) and warm—wet (54.1%) seasons. Pronghorn diet also shifted to shrubs during drought (50.7%). Gemsbok diets were evenly distributed across forage types. Fifty-three percent of the species of plants consumed by pronghorn and gemsbok were shared; diet overlap averaged 0.44 ± 0.06 (SE) and 0.49 ± 0.06 during the warm—dry seasons of 2010 and 2011, respectively. During drought, key forage species shared between pronghorn and gemsbok included yucca Yucca spp., prickly pear Opuntia spp., globemallow Sphaeralcea coccinea and horsenettle Solanum elaeagnifolium, comprising 50% of the pronghorn and 40% of the gemsbok diets. Fecal nitrogen and FDAPA decreased in pronghorn by 26% and 27% between the warm—dry season of 2010 (non-drought) and the warm—dry season of 2011 (drought), respectively. Drought had little effect on dietary quality for gemsbok. Gemsbok can use forage with lower nutritional content giving them an advantage over pronghorn, particularly during drought periods. Pronghorn are more dependent upon

Genetic complexity of miscanthus cell wall composition and biomass quality for biofuels.

Science.gov (United States)

van der Weijde, Tim; Kamei, Claire L Alvim; Severing, Edouard I; Torres, Andres F; Gomez, Leonardo D; Dolstra, Oene; Maliepaard, Chris A; McQueen-Mason, Simon J; Visser, Richard G F; Trindade, Luisa M

2017-05-25

Miscanthus sinensis is a high yielding perennial grass species with great potential as a bioenergy feedstock. One of the challenges that currently impedes commercial cellulosic biofuel production is the technical difficulty to efficiently convert lignocellulosic biomass into biofuel. The development of feedstocks with better biomass quality will improve conversion efficiency and the sustainability of the value-chain. Progress in the genetic improvement of biomass quality may be substantially expedited by the development of genetic markers associated to quality traits, which can be used in a marker-assisted selection program. To this end, a mapping population was developed by crossing two parents of contrasting cell wall composition. The performance of 182 F1 offspring individuals along with the parents was evaluated in a field trial with a randomized block design with three replicates. Plants were phenotyped for cell wall composition and conversion efficiency characters in the second and third growth season after establishment. A new SNP-based genetic map for M. sinensis was built using a genotyping-by-sequencing (GBS) approach, which resulted in 464 short-sequence uniparental markers that formed 16 linkage groups in the male map and 17 linkage groups in the female map. A total of 86 QTLs for a variety of biomass quality characteristics were identified, 20 of which were detected in both growth seasons. Twenty QTLs were directly associated to different conversion efficiency characters. Marker sequences were aligned to the sorghum reference genome to facilitate cross-species comparisons. Analyses revealed that for some traits previously identified QTLs in sorghum occurred in homologous regions on the same chromosome. In this work we report for the first time the genetic mapping of cell wall composition and bioconversion traits in the bioenergy crop miscanthus. These results are a first step towards the development of marker-assisted selection programs in miscanthus

Developing a composite weighted quality metric to reflect the total benefit conferred by a health plan.

Science.gov (United States)

Taskler, Glen B; Braithwaite, R Scott

2015-03-01

To improve individual health quality measures, which are associated with varying degrees of health benefit, and composite quality metrics, which weight individual measures identically. We developed a health-weighted composite quality measure reflecting the total health benefit conferred by a health plan annually, using preventive care as a test case. Using national disease prevalence, we simulated a hypothetical insurance panel of individuals aged 25 to 84 years. For each individual, we estimated the gain in life expectancy associated with 1 year of health system exposure to encourage adherence to major preventive care guidelines, controlling for patient characteristics (age, race, gender, comorbidity) and variation in individual adherence rates. This personalized gain in life expectancy was used to proxy for the amount of health benefit conferred by a health plan annually to its members, and formed weights in our health-weighted composite quality measure. We aggregated health benefits across the health insurance membership panel to analyze total health system performance. Our composite quality metric gave the highest weights to health plans that succeeded in implementing tobacco cessation and weight loss. One year of compliance with these goals was associated with 2 to 10 times as much health benefit as compliance with easier-to-follow preventive care services, such as mammography, aspirin, and antihypertensives. For example, for women aged 55 to 64 years, successful interventions to encourage weight loss were associated with 2.1 times the health benefit of blood pressure reduction and 3.9 times the health benefit of increasing adherence with screening mammography. A single health-weighted quality metric may inform measurement of total health system performance.

Relational Resources of a University as a Source of Education Quality Assurance

Science.gov (United States)

Bagdasaryan, Irina; Vasilyeva, Zoya; Almabekova, Olga

2015-01-01

This paper considers high quality educational services provided by a university being the highest priority and assumes relational resources as valuable sources that can facilitate and enhance quality assurance. Each university with a unique resource base is connected with a variety of entities--other universities, non-profit and for-profit…

Mycoflora and Water Quality index Assessment of Water Sources in ...

African Journals Online (AJOL)

MICHAEL HORSFALL

water sources (31.96 - 47.31) falls within the classification “Bad” despite the slight increase during the dry season. The quality of water in the study area is poor and portends health risk; ... tributary that originates from the New Calabar River.

High dose-rate brachytherapy source position quality assurance using radiochromic film

International Nuclear Information System (INIS)

Evans, M.D.C.; Devic, S.; Podgorsak, E.B.

2007-01-01

Traditionally, radiographic film has been used to verify high-dose-rate brachytherapy source position accuracy by co-registering autoradiographic and diagnostic images of the associated applicator. Filmless PACS-based clinics that do not have access to radiographic film and wet developers may have trouble performing this quality assurance test in a simple and practical manner. We describe an alternative method for quality assurance using radiochromic-type film. In addition to being easy and practical to use, radiochromic film has some advantages in comparison with traditional radiographic film when used for HDR brachytherapy quality assurance

Quality assurance program plan for FRG sealed isotopic heat sources project (C-229)

International Nuclear Information System (INIS)

Tanke, J.M.

1997-01-01

This QAPP implements the Quality Assurance Program Plan for the FRG Sealed Isotopic Heat Sources Project (C-229). The heat source will be relocated from the 324 Building and placed in interim storage at the Central Waste Complex (CWC)

Primary magmas and mantle sources of Emeishan basalts constrained from major element, trace element and Pb isotope compositions of olivine-hosted melt inclusions

Science.gov (United States)

Ren, Zhong-Yuan; Wu, Ya-Dong; Zhang, Le; Nichols, Alexander R. L.; Hong, Lu-Bing; Zhang, Yin-Hui; Zhang, Yan; Liu, Jian-Qiang; Xu, Yi-Gang

2017-07-01

Olivine-hosted melt inclusions within lava retain important information regarding the lava's primary magma compositions and mantle sources. Thus, they can be used to infer the nature of the mantle sources of large igneous provinces, which is still not well known and of the subject of debate. We have analysed the chemical compositions and Pb isotopic ratios of olivine-hosted melt inclusions in the Dali picrites, Emeishan Large Igneous Province (LIP), SW China. These are the first in-situ Pb isotope data measured for melt inclusions found in the Emeishan picrites and allow new constraints to be placed on the source lithology of the Emeishan LIP. The melt inclusions show chemical compositional variations, spanning low-, intermediate- and high-Ti compositions, while their host whole rocks are restricted to the intermediate-Ti compositions. Together with the relatively constant Pb isotope ratios of the melt inclusions, the compositional variations suggest that the low-, intermediate- and high-Ti melts were derived from compositionally similar sources. The geochemical characteristics of melt inclusions, their host olivines, and whole-rocks from the Emeishan LIP indicate that Ca, Al, Mn, Yb, and Lu behave compatibly, and Ti, Rb, Sr, Zr, and Nb behave incompatibly during partial melting, requiring a pyroxenite source for the Emeishin LIP. The wide range of Ti contents in the melt inclusions and whole-rocks of the Emeishan basalts reflects different degrees of partial melting in the pyroxenite source at different depths in the melting column. The Pb isotope compositions of the melt inclusions and the OIB-like trace element compositions of the Emeishan basalts imply that mixing of a recycled ancient oceanic crust (EM1-like) component with a peridotite component from the lower mantle (FOZO-like component) could have underwent solid-state reaction, producing a secondary pyroxenite source that was subsequently partially melted to form the basalts. This new model of pyroxenite

Classifying Sources Influencing Indoor Air Quality (IAQ Using Artificial Neural Network (ANN

Directory of Open Access Journals (Sweden)

Shaharil Mad Saad

2015-05-01

Full Text Available Monitoring indoor air quality (IAQ is deemed important nowadays. A sophisticated IAQ monitoring system which could classify the source influencing the IAQ is definitely going to be very helpful to the users. Therefore, in this paper, an IAQ monitoring system has been proposed with a newly added feature which enables the system to identify the sources influencing the level of IAQ. In order to achieve this, the data collected has been trained with artificial neural network or ANN—a proven method for pattern recognition. Basically, the proposed system consists of sensor module cloud (SMC, base station and service-oriented client. The SMC contain collections of sensor modules that measure the air quality data and transmit the captured data to base station through wireless network. The IAQ monitoring system is also equipped with IAQ Index and thermal comfort index which could tell the users about the room’s conditions. The results showed that the system is able to measure the level of air quality and successfully classify the sources influencing IAQ in various environments like ambient air, chemical presence, fragrance presence, foods and beverages and human activity.

Composite measures of watershed health from a water quality perspective.

Science.gov (United States)

Mallya, Ganeshchandra; Hantush, Mohamed; Govindaraju, Rao S

2018-05-15

Water quality data at gaging stations are typically compared with established federal, state, or local water quality standards to determine if violations (concentrations of specific constituents falling outside acceptable limits) have occurred. Based on the frequency and severity of water quality violations, risk metrics such as reliability, resilience, and vulnerability (R-R-V) are computed for assessing water quality-based watershed health. In this study, a modified methodology for computing R-R-V measures is presented, and a new composite watershed health index is proposed. Risk-based assessments for different water quality parameters are carried out using identified national sampling stations within the Upper Mississippi River Basin, the Maumee River Basin, and the Ohio River Basin. The distributional properties of risk measures with respect to water quality parameters are reported. Scaling behaviors of risk measures using stream order, specifically for the watershed health (WH) index, suggest that WH values increased with stream order for suspended sediment concentration, nitrogen, and orthophosphate in the Upper Mississippi River Basin. Spatial distribution of risk measures enable identification of locations exhibiting poor watershed health with respect to the chosen numerical standard, and the role of land use characteristics within the watershed. Copyright © 2018 Elsevier Ltd. All rights reserved.

Exploring the Effects of Geographical Origin on the Chemical Composition and Quality Grading of Vitis vinifera L. cv. Chardonnay Grapes.

Science.gov (United States)

Gambetta, Joanna M; Cozzolino, Daniel; Bastian, Susan E P; Jeffery, David W

2017-01-31

The relationship between berry chemical composition, region of origin and quality grade was investigated for Chardonnay grapes sourced from vineyards located in seven South Australian Geographical Indications (GI). Measurements of basic chemical parameters, amino acids, elements, and free and bound volatiles were conducted for grapes collected during 2015 and 2016. Multiple factor analysis (MFA) was used to determine the sets of data that best discriminated each GI and quality grade. Important components for the discrimination of grapes based on GI were 2-phenylethanol, benzyl alcohol and C6 compounds, as well as Cu, Zn, and Mg, titratable acidity (TA), total soluble solids (TSS), and pH. Discriminant analysis (DA) based on MFA results correctly classified 100% of the samples into GI in 2015 and 2016. Classification according to grade was achieved based on the results for elements such as Cu, Na, Fe, volatiles including C6 and aryl alcohols, hydrolytically-released volatiles such as (Z)-linalool oxide and vitispirane, pH, TSS, alanine and proline. Correct classification through DA according to grade was 100% for both vintages. Significant correlations were observed between climate, GI, grade, and berry composition. Climate influenced the synthesis of free and bound volatiles as well as amino acids, sugars, and acids, as a result of higher temperatures and precipitation.

Addition of enzymes to improve sensory quality of composite wheat–cassava bread

DEFF Research Database (Denmark)

Serventi, Luca; Jensen, Sidsel; Skibsted, Leif Horsfelt

2016-01-01

Composite wheat–cassava (WC) bread was recently proposed as a sustainable alternative to wheat bread. Nonetheless, using >20 % cassava flour on flour basis in bread baking has consistently been proven to impair the sensory quality. Selected enzymes: fungal alpha-amylase Fungamyl® 2500 SG (Fungamy...

Indoor air quality environmental information handbook: Combustion sources

Energy Technology Data Exchange (ETDEWEB)

1990-06-01

This environmental information handbook was prepared to assist both the non-technical reader (i.e., homeowner) and technical persons (such as researchers, policy analysts, and builders/designers) in understanding the current state of knowledge regarding combustion sources of indoor air pollution. Quantitative and descriptive data addressing the emissions, indoor concentrations, factors influencing indoor concentrations, and health effects of combustion-generated pollutants are provided. In addition, a review of the models, controls, and standards applicable to indoor air pollution from combustion sources is presented. The emphasis is on the residential environment. The data presented here have been compiled from government and privately-funded research results, conference proceedings, technical journals, and recent publications. It is intended to provide the technical reader with a comprehensive overview and reference source on the major indoor air quality aspects relating to indoor combustion activities, including tobacco smoking. In addition, techniques for determining potential concentrations of pollutants in residential settings are presented. This is an update of a 1985 study documenting the state of knowledge of combustion-generated pollutants in the indoor environment. 191 refs., 51 figs., 71 tabs.

Seasonal Variation in Drinking and Domestic Water Sources and Quality in Port Harcourt, Nigeria

Science.gov (United States)

Kumpel, Emily; Cock-Esteb, Alicea; Duret, Michel; de Waal, Dominick; Khush, Ranjiv

2017-01-01

We compared dry and rainy season water sources and their quality in the urban region of Port Harcourt, Nigeria. Representative sampling indicated that municipal water supplies represent < 1% of the water sources. Residents rely on privately constructed and maintained boreholes that are supplemented by commercially packaged bottled and sachet drinking water. Contamination by thermotolerant coliforms increased from 21% of drinking water sources in the dry season to 42% of drinking water sources in the rainy season (N = 356 and N = 397). The most significant increase was in sachet water, which showed the lowest frequencies of contamination in the dry season compared with other sources (15%, N = 186) but the highest frequencies during the rainy season (59%, N = 76). Only half as many respondents reported drinking sachet water in the rainy season as in the dry season. Respondents primarily used flush or pour-flush toilets connected to septic tanks (85%, N = 399). The remainder relied on pit latrines and hanging (pier) latrines that drained into surface waters. We found significant associations between fecal contamination in boreholes and the nearby presence of hanging latrines. Sanitary surveys of boreholes showed that more than half were well-constructed, and we did not identify associations between structural or site deficiencies and microbial water quality. The deterioration of drinking water quality during the rainy season is a serious public health risk for both untreated groundwater and commercially packaged water, highlighting a need to address gaps in monitoring and quality control. PMID:27821689

Seasonal changes in particulate and dissolved organic matter composition and quality in the Lena River Delta

Science.gov (United States)

Mollenhauer, G.; Winterfeld, M.; Hefter, J.; Bodenstab, L.; Morgenstern, A.; Eulenburg, A.; Heim, B.; Koch, B.; Schefuss, E.; Moerth, C. M.; Rethemeyer, J.

2016-12-01

Arctic rivers are known to export large quantities of carbon by discharge of dissolved and particulate organic carbon (DOC, POC), and in a warming and progressively moister Arctic, these exports may increase resulting in a reduction of arctic continental carbon stocks. These rivers have highly variable discharge rates with a pronounced maximum during the spring freshet associated with highest concentrations of DOC and POC. Most studies investigating the isotopic composition and quality of carbon exported by Arctic rivers rely on samples taken in summer during base flow, which is due to the logistical challenges associated with sampling in the remote Arctic permafrost regions. Here we present a record of δ13C and Δ14C of DOC and POC collected between late May during the freshet and late August 2014 in the Lena River Delta. POC Δ14C shows an initial trend towards older values in the spring samples, which is reversed in summer, associated with a shift towards more depleted δ13C values. We interpret this aging trend as reflecting progressive thawing throughout the ice-free season, resulting in mobilization of progressively older carbon from deeper thawed layers. The summer reversal indicates admixture of aquatic organic matter. DOC Δ14C, in contrast, remains at relatively modern levels with rather constant δ13C values throughout the sampling period. We furthermore analysed the biomarker composition of Lena Delta particulate OM collected in spring and summer. From spring to summer, we observe trends in abundance of individual leaf-wax derived biomarkers indicating higher abundance of algal biomass in the summer particles. Trends in soil microbial biomarkers and compound-specific δD of leaf-wax lipids suggest a shift in sources towards higher contributions from the southern catchment in summer. DOC composition investigated with FT-ICR-MS changes from spring with higher abundances of compounds with high H/C and low O/C ratios to late summer, when fewer compounds

Effect of Hydrocolloids and Emulsifiers on Baking Quality of Composite Cassava-Maize-Wheat Breads

Directory of Open Access Journals (Sweden)

Maria Eduardo

2014-01-01

Full Text Available Cassava is widely available worldwide but bread quality is impaired when cassava is used in the bread formulation. To overcome this problem, different improvers were tested in the preparation of composite cassava-maize-wheat (CMW breads. Emulsifiers, diacetyl tartic acid ester of monoglycerides (DATEM, sodium stearoyl-2-lactylate (SSL, and lecithin (LC; and hydrocolloids, carboxymethylcellulose (CMC and high-methylated pectin (HM pectin were added during dough preparation of the composite flours (cassava-maize-wheat, 40 : 10 : 50. Each emulsifier was tested in combination with the hydrocolloids at levels of 0.1, 0.3, and 0.5% while hydrocolloids were used at a level of 3%. Bread quality attributes such as specific loaf volume, crust colour, crumb moisture, and firmness were measured. The specific volume of the fresh breads significantly improved with the addition of hydrocolloids (7.5 and 13% and in combination with emulsifiers (from 7.9 to 27% compared with bread produced without improvers. A significant improvement of brownness index and firmness of the composite flours breads was achieved with the addition of hydrocolloids and emulsifiers. The results show that emulsifiers and hydrocolloids can significantly improve the baking quality of CMW breads and thereby enhance the potential for using locally produced flours in bread baking.

The impact of moisture sources on the oxygen isotope composition of precipitation at a continental site in central Europe

Science.gov (United States)

Krklec, Kristina; Domínguez-Villar, David; Lojen, Sonja

2018-06-01

The stable isotope composition of precipitation records processes taking place within the hydrological cycle. Potentially, moisture sources are important controls on the stable isotope composition of precipitation, but studies focused on this topic are still scarce. We studied the moisture sources contributing to precipitation at Postojna (Slovenia) from 2009 to 2013. Back trajectory analyses were computed for the days with precipitation at Postojna. The moisture uptake locations were identified along these trajectories using standard hydrometeorological formulation. The moisture uptake locations were integrated in eight source regions to facilitate its comparison to the monthly oxygen isotope composition (δ18O values) of precipitation. Nearly half of the precipitation originated from continental sources (recycled moisture), and >40% was from central and western Mediterranean. Results show that moisture sources do not have a significant impact on the oxygen isotope composition at this site. We suggest that the large proportion of recycled moisture originated from transpiration rather than evaporation, which produced water vapour with less negative δ18O values. Thus the difference between the oceanic and local vapour source was reduced, which prevented the distinction of the moisture sources based on their oxygen isotope signature. Nevertheless, δ18O values of precipitation are partially controlled by climate parameters, which is of major importance for paleoclimate studies. We found that the main climate control on Postojna δ18O values of precipitation is the surface temperature. Amount effect was not recorded at this site, and the winter North Atlantic Oscillation (NAO) does not impact the δ18O values of precipitation. The Western Mediterranean Oscillation (WeMO) was correlated to oxygen stable isotope composition, although this atmospheric pattern was not a control. Instead we found that the link to δ18O values results from synoptic scenarios affecting We

Seasonality Affects the Diversity and Composition of Bacterioplankton Communities in Dongjiang River, a Drinking Water Source of Hong Kong

Directory of Open Access Journals (Sweden)

Wei Sun

2017-08-01

Full Text Available Water quality ranks the most vital criterion for rivers serving as drinking water sources, which periodically changes over seasons. Such fluctuation is believed associated with the state shifts of bacterial community within. To date, seasonality effects on bacterioplankton community patterns in large rivers serving as drinking water sources however, are still poorly understood. Here we investigated the intra-annual bacterial community structure in the Dongjiang River, a drinking water source of Hong Kong, using high-throughput pyrosequencing in concert with geochemical property measurements during dry, and wet seasons. Our results showed that Proteobacteria, Actinobacteria, and Bacteroidetes were the dominant phyla of bacterioplankton communities, which varied in composition, and distribution from dry to wet seasons, and exhibited profound seasonal changes. Actinobacteria, Bacteroidetes, and Cyanobacteria seemed to be more associated with seasonality that the relative abundances of Actinobacteria, and Bacteroidetes were significantly higher in the dry season than those in the wet season (p < 0.01, while the relative abundance of Cyanobacteria was about 10-fold higher in the wet season than in the dry season. Temperature and NO3--N concentration represented key contributing factors to the observed seasonal variations. These findings help understand the roles of various bacterioplankton and their interactions with the biogeochemical processes in the river ecosystem.

Source apportionment of social support and quality of life index ...

African Journals Online (AJOL)

Source apportionment of social support and quality of life index among drug abuse inmates using multiple linear regression. ... The data from 12 prisons selected in Peninsular Malaysia was collected during the period April and June 2015. The 1753 respondents were selected using simple random sampling. The method of ...

California Air Quality State Implementation Plans; Final Approval; Butte County Air Quality Management District; Stationary Source Permits

Science.gov (United States)

EPA is taking final action to approve a revision to the Butte County Air Quality Management District (BCAQMD) portion of the California State Implementation Plan (SIP). This revision concerns the District's New Source Review (NSR) permitting program.

Quality assurance of Vari-source high dose rate (HDR) brachytherapy- remote after loader and cost effectiveness of Vari-source HDR- brachytherapy: NORI, Islamabad experience

International Nuclear Information System (INIS)

Ahmad, N.; Mahmood, H.; Jafri, S.R.A.

2004-01-01

A quality control of Vari-Source high dose rate (HDR) remote after loading brachytherapy machine was carried out and the cost effectiveness of HDR brachytherapy machine was also evaluated considering the cost of ten Iridium-192 wire sources at Nuclear Medicine, Oncology and Radiotherapy Institute (NORI), Islamabad, Pakistan. A total number of 253 intracavitary insertions were done in 98 patients from October 1996 to May 2001. The results of the quality control tests performed during 1996 to 2001 were within the acceptable limits. The cost effectiveness of Vari-Source HDR brachytherapy machine was also evaluated. The average cost per patient was calculated as US$ 491. Small number of patients was treated as the machine was used for gynecologic malignancies only. The objective was to assess the quality control status of HDR brachytherapy machine on patient treatment day, source exchange day and periodic day (monthly basis). It was found that the cost per patient can be minimized if other type of cancer patients are also treated on Vari-Source HDR machine. (author)

Influence of using a blend of rennet casein and whey protein concentrate as protein source on the quality of Mozzarella cheese analogue.

Science.gov (United States)

Dhanraj, Padhiyar; Jana, Atanu; Modha, Hiral; Aparnathi, K D

2017-03-01

The effect of incorporating whey protein concentrate (WPC) on the quality characteristics of Mozzarella cheese analogue (MCA) based on rennet casein (RC) was studied. The proportion of RC:WPC tried out were 95:5, 90:10, and 85:15 w/w. The formulation of MCA comprised of 23.5% of blend of RC and WPC, 15% specialty vegetable fat, 2.75% trisodium citrate + disodium hydrogen orthophosphate (2.5:1, w/w), 0.07% calcium chloride, 0.6% citric acid, 1.1% NaCl, 1.5% cheese bud flavoring, and rest water. Varying the proportion of RC and WPC had a significant influence on the composition, textural properties, baking qualities and sensory quality of MCA judged as a topping on pizza pie. MCA made using protein blends (RC:WPC-90:10 or 85:15) behaved satisfactorily during pizza baking trials. However, looking at the superiority of MCA made using RC:WPC (90:10) with regard to shred quality and marginal superiority in terms of the total sensory score of cheese, judged as pizza topping, the former blend (i.e. RC:WPC, 90:10) was selected. The MCA obtained employing such protein blend had composition similar to that of Pizza cheese prepared from cheese milk and had requisite baking characteristics needed as a pizza topping. It is recommended to use a blend of RC and WPC (90:10) as the protein source in the formulation of MCA to obtain nutritionally superior cheese product having desired functional properties for its end use in baking applications.

Effects of goat milk or milk replacer diet on meat quality and fat composition of suckling goat kids.

Science.gov (United States)

Bañón, S; Vila, R; Price, A; Ferrandini, E; Garrido, M D

2006-02-01

The effects of a diet with goat milk "GM" or milk replacer "MR" on the meat quality and fat composition of suckling Murciano-Granadina kids were studied. MR consisted of powdered skimmed milk, coconut oil and fat, and cereal products and by-products. Raw meat quality (moisture, protein, lipids, ash, collagen, cholesterol, haem pigments, CIELab colour, pH and water retention capacity), fatty acid "FA" composition and eating quality of cooked meat (odour, flavour and texture) were determined. Diet had only a slight effect on raw meat quality but had a pronounced effect on fatty acid composition and eating quality of cooked meat. MR diet increased the water/protein proportion in the muscle. The saturated/unsaturated FA ratio in GM and MR fat was 0.94 and 2.27, respectively. The major FA in GM and MR fat were C16:0 and C18:1, respectively. Short-chain C4-C12 hardly accumulated in the adipose tissue of suckling kid, increasing the relative percentages of C14-C20. This effect was more pronounced in MR fat, due to the fact that MR contained more short-chain fatty acids than GM. MR diet gave cooked meat a more intense characteristic goat meat odour and flavour, more tenderness and more juiciness than the natural suckling diet. This fact could be related to differences in meat and fat composition.

Chemical Composition and Quality Characteristics of Wheat Bread Supplemented with Leafy Vegetable Powders

Directory of Open Access Journals (Sweden)

T. V. Odunlade

2017-01-01

Full Text Available The study investigated the effect of supplementation of the leaf powders of Telfairia occidentalis, Amaranthus viridis, and Solanum macrocarpon on the chemical composition and the quality characteristics of wheat bread. The bread samples were supplemented with each of the vegetable leaf powders at 1%, 2%, and 3% during preparation. The bread samples were assayed for proximate composition, mineral composition, physical, sensory, and antioxidant properties using standard methods. The addition of vegetable powders significantly increased the protein (9.50 to 13.93%, fibre (1.81 to 4.00%, ash (1.05 to 2.38%, and fat (1.27 to 2.00%. Supplementation with vegetable powder however significantly decreased (p<0.05 the carbohydrate and moisture contents. Significant (p<0.05 increases were recorded for all evaluated minerals as the level of vegetable powder increased. Supplementation with vegetable powder caused significant decrease in total phenolic content, percentage DPPH inhibition, metal chelating ability, ferric reducing antioxidant power, and total antioxidant capacity. Sensory results showed that there was significant decrease in sensory qualities with increasing supplementation. This therefore suggests that bread supplemented with vegetable powder could have more market penetration if awareness is highly created.

Google vs. the Library (Part III): Assessing the Quality of Sources Found by Undergraduates

Science.gov (United States)

Georgas, Helen

2015-01-01

This study assesses and compares the quality of sources found by undergraduate students when doing research using both Google and a library (federated) search tool. Thirty undergraduates were asked to find four sources (one book, two articles, and one additional source of their choosing) related to a selected research topic. Students used both…

Quality correction factors of composite IMRT beam deliveries: Theoretical considerations

International Nuclear Information System (INIS)

Bouchard, Hugo

2012-01-01

Purpose: In the scope of intensity modulated radiation therapy (IMRT) dosimetry using ionization chambers, quality correction factors of plan-class-specific reference (PCSR) fields are theoretically investigated. The symmetry of the problem is studied to provide recommendable criteria for composite beam deliveries where correction factors are minimal and also to establish a theoretical limit for PCSR delivery k Q factors. Methods: The concept of virtual symmetric collapsed (VSC) beam, being associated to a given modulated composite delivery, is defined in the scope of this investigation. Under symmetrical measurement conditions, any composite delivery has the property of having a k Q factor identical to its associated VSC beam. Using this concept of VSC, a fundamental property of IMRT k Q factors is demonstrated in the form of a theorem. The sensitivity to the conditions required by the theorem is thoroughly examined. Results: The theorem states that if a composite modulated beam delivery produces a uniform dose distribution in a volume V cyl which is symmetric with the cylindrical delivery and all beams fulfills two conditions in V cyl : (1) the dose modulation function is unchanged along the beam axis, and (2) the dose gradient in the beam direction is constant for a given lateral position; then its associated VSC beam produces no lateral dose gradient in V cyl , no matter what beam modulation or gantry angles are being used. The examination of the conditions required by the theorem lead to the following results. The effect of the depth-dose gradient not being perfectly constant with depth on the VSC beam lateral dose gradient is found negligible. The effect of the dose modulation function being degraded with depth on the VSC beam lateral dose gradient is found to be only related to scatter and beam hardening, as the theorem holds also for diverging beams. Conclusions: The use of the symmetry of the problem in the present paper leads to a valuable theorem showing

Metagenomic sequencing reveals the relationship between microbiota composition and quality of Chinese Rice Wine.

Science.gov (United States)

Hong, Xutao; Chen, Jing; Liu, Lin; Wu, Huan; Tan, Haiqin; Xie, Guangfa; Xu, Qian; Zou, Huijun; Yu, Wenjing; Wang, Lan; Qin, Nan

2016-05-31

Chinese Rice Wine (CRW) is a common alcoholic beverage in China. To investigate the influence of microbial composition on the quality of CRW, high throughput sequencing was performed for 110 wine samples on bacterial 16S rRNA gene and fungal Internal Transcribed Spacer II (ITS2). Bioinformatic analyses demonstrated that the quality of yeast starter and final wine correlated with microbial taxonomic composition, which was exemplified by our finding that wine spoilage resulted from a high proportion of genus Lactobacillus. Subsequently, based on Lactobacillus abundance of an early stage, a model was constructed to predict final wine quality. In addition, three batches of 20 representative wine samples selected from a pool of 110 samples were further analyzed in metagenomics. The results revealed that wine spoilage was due to rapid growth of Lactobacillus brevis at the early stage of fermentation. Gene functional analysis indicated the importance of some pathways such as synthesis of biotin, malolactic fermentation and production of short-chain fatty acid. These results led to a conclusion that metabolisms of microbes influence the wine quality. Thus, nurturing of beneficial microbes and inhibition of undesired ones are both important for the mechanized brewery.

Forage Quality and Composition Measurements as Predictors of Ethanol Yield from Maize (Zea mays L.) Stover

Science.gov (United States)

Improvement of biofeedstock quality for cellulosic ethanol production will be facilitated by inexpensive and rapid methods of evaluation, such as those already employed in the field of ruminant nutrition. Our objective was to evaluate whether forage quality and compositional measurements could be u...

Writing Week-Journals to Improve the Writing Quality of Fourth-Graders' Compositions

Science.gov (United States)

Rosário, Pedro; Högemann, Julia; Núñez, José Carlos; Vallejo, Guillermo; Cunha, Jennifer; Oliveira, Vera; Fuentes, Sonia; Rodrigues, Celestino

2017-01-01

Students' writing problems are a global educational concern and is in need of particular attention. This study aims to examine the impact of providing extra writing opportunities (i.e., writing journals) on the quality of writing compositions. A longitudinal cluster-randomized controlled design using a multilevel modeling analysis with 182 fourth…

Effects of abiotic stress and crop management on cereal grain composition: implications for food quality and safety.

Science.gov (United States)

Halford, Nigel G; Curtis, Tanya Y; Chen, Zhiwei; Huang, Jianhua

2015-03-01

The effects of abiotic stresses and crop management on cereal grain composition are reviewed, focusing on phytochemicals, vitamins, fibre, protein, free amino acids, sugars, and oils. These effects are discussed in the context of nutritional and processing quality and the potential for formation of processing contaminants, such as acrylamide, furan, hydroxymethylfurfuryl, and trans fatty acids. The implications of climate change for cereal grain quality and food safety are considered. It is concluded that the identification of specific environmental stresses that affect grain composition in ways that have implications for food quality and safety and how these stresses interact with genetic factors and will be affected by climate change needs more investigation. Plant researchers and breeders are encouraged to address the issue of processing contaminants or risk appearing out of touch with major end-users in the food industry, and not to overlook the effects of environmental stresses and crop management on crop composition, quality, and safety as they strive to increase yield. © The Author 2014. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Ranking sources of hospital quality information for orthopedic surgery patients: consequences for the system of managed competition.

Science.gov (United States)

Bes, Romy Evelien; van den Berg, Bernard

2013-01-01

Healthcare quality information is crucial for the system of managed competition. Within a system of managed competition, health insurers can selectively contract care providers and are allowed to channel patients towards contracted providers. The idea is that insurers have a stronger bargaining position compared to care providers when they are able to channel patients. In the Dutch system of managed competition that was implemented in 2006, channelling patients to preferred providers has not yet been very successful. Empirical knowledge of which sources of hospital quality information they find important may help us to understand how to channel patients to preferred providers. The objective of this survey was to measure how patients rank various sources of information when they compare hospital quality in a system of managed competition. A written survey was conducted among clients of a large Dutch health insurance company. These clients underwent orthopedic surgery on the hip or knee no longer than 12 months ago. Two major players within a system of managed competition-health insurers and the government-were not seen as important sources of hospital quality information. In contrast, own experience and general practitioners (GPs) were seen as the most important sources of hospital quality information within the Dutch system of managed competition. Health insurers should take the main finding-that GPs are the most important source of hospital quality information-into account when they contract care providers and develop strategies for channeling patients towards preferred providers. A well-functioning system of managed competition will benefit patients, as it involves incentives for care providers to increase healthcare quality and to produce at the lowest cost per unit of quality.

Formation and migration of Natural Gases: gas composition and isotopes as monitors between source, reservoir and seep

Science.gov (United States)

Schoell, M.; Etiope, G.

2015-12-01

Natural gases form in tight source rocks at temperatures between 120ºC up to 200ºC over a time of 40 to 50my depending on the heating rate of the gas kitchen. Inferring from pyrolysis experiments, gases after primary migration, a pressure driven process, are rich in C2+ hydrocarbons (C2 to C5). This is consistent with gas compositions of oil-associated gases such as in the Bakken Shale which occur in immediate vicinity of the source with little migration distances. However, migration of gases along porous rocks over long distances (up to 200km in the case of the Troll field offshore Norway) changes the gas composition drastically as C2+ hydrocarbons tend to be retained/sequestered during migration of gas as case histories from Virginia and the North Sea will demonstrate. Similar "molecular fractionation" is observed between reservoirs and surface seeps. In contrast to gas composition, stable isotopes in gases are, in general, not affected by the migration process suggesting that gas migration is a steady state process. Changes in isotopic composition, from source to reservoir to surface seeps, is often the result of mixing of gases of different origins. Examples from various gas provinces will support this notion. Natural gas basins provide little opportunity of tracking and identifying gas phase separation. Future research on experimental phase separation and monitoring of gas composition and gas ratio changes e.g. various C2+ compound ratios over C1 or isomer ratios such as iso/n ratios in butane and pentane may be an avenue to develop tracers for phase separation that could possibly be applied to natural systems of retrograde natural condensate fields.

Pesticide residues in individual versus composite samples of apples after fine or coarse spray quality application

NARCIS (Netherlands)

Poulsen, M.; Wenneker, M.; Withagen, J.C.M.; Christensen, H.B.

2012-01-01

In this study, field trials on fine and coarse spray quality application of pesticides on apples were performed. The main objectives were to study the variation of pesticide residue levels in individual fruits versus composite samples, and the effect of standard fine spray quality application versus

X-ray fluorescence analysis of substance composition using two radiation sources of different energies

International Nuclear Information System (INIS)

Varvaritsa, V.P.; Martishchenko, L.G.

1980-01-01

An X-ray radiometric method of determining substance composition, based on using two fluxes of primary radiation with energies above absorption edge of the determined element, is suggested. The method permits to decrease matrix effect and to obtain linear dependence between the measuring results and the determined value (concentration). The method has the following advantages: 1) increased accuracy during analyzing substances of complex composition; 2) absence of necessity to know beforehand composition of the analyzed element and its variations; 3) simplicity of choice of primary radiation energies; 4) simplicity of equipment realization; 5) possibility of graduating the equipment directly in concentration units. The suggested method has been tested during measuring Zn concentration in samples, containing S, Ba, Ca and polyethylene, 109 Cd and 238 Pu have been used as sources [ru

The APHH China Research Programme: Chemical Composition and Source Apportionment of Particulate Matter in Beijing

Science.gov (United States)

Vu, T.; Shi, Z.; Liu, D.; Harrison, R. M.; Wu, X.; Brean, J.; Fu, P.

2017-12-01

There is increasing evidence that atmospheric particles have adverse effects on human health due to their high toxic properties. Consequently, atmospheric particles are getting much attention from the public, especially from developing megacities which have a large population and high air pollution levels. Beijing, which is one of largest megacities of the world with more than 20 million inhabitants living under very poor air quality conditions is an ideal metropolitan region to study the processes and sources of atmospheric particles in order to improve strategies for air pollution management. This study is aimed to investigate comprehensively the sources of particles in Beijing by application of a wide range of instruments, techniques and modelling approaches. Two intensive sampling campaigns were carried out during the winter 2016 and the summer 2017 at the Institute of Atmospheric Physics (IAP, the urban site) and Pinggu (the rural site) in Beijing. Online instruments including Api-TOF, PSM, and SMPS systems were deployed to investigate the size distribution and chemical composition of particles. Contemporaneously, both fine and coarse particles were collected on PTFE and quartz fibre filters using high and medium volume air samplers. Those filters were then analysed for quantification of inorganic ions by ion chromatography, elemental composition using XRF, PIXE and ICP-MS techniques, and EC/OC using a Sunset OC-EC aerosol analyser, organic markers using GC-MS techniques. The mean daily concentration of PM2.5 at the urban site of Beijing was 92.0±66.4 µg/m3 and 31.2±14.7 µg/m3 for winter and summer campaigns, while those levels measured at the rural site were 86.7±58.9 and 27.6±13.3 µg/m3. The concentration of OC and EC measured during the winter campaign was 22.3 and 3.4 µg/m3 respectively. By using a mass closure model, it was found that secondary inorganic aerosols and soil dust accounted for 32.6% and 9.7% of fine particles at IAP. High

Linseed fibre – effect on composite flour properties and cereal products quality

Directory of Open Access Journals (Sweden)

Marie Hrušková

2017-01-01

Full Text Available Wheat flour was fortified by 2.5 or 5.0 wt. per cent of linseed fibre, gained from seeds of golden flax varieties Amon and Raciol and brown one Recital (granulation 500 - 700 m, prepared from 2015 harvest. Technological quality of six flour composites was described analytically by Falling Number and Zeleny sedimentation test. Both screening methods shown a little impact on amylases activity and protein quality, respectively. Rheological tests included the farinograph, the extensigraph and the Rapid Visco Analyser (RVA proofs. Additions of brown and yellow flax fibre significantly increased farinograph water absorption and shortened dough stability, somewhat stronger by addition of brown linseed fibre. Extensigraph curves course depended on dough resting time, higher differences between wheat control and flour composites were observed after 60 min dough resting. Linseed fibre supported dough extensibility, and energy as area under curve significantly decreased about 7 - 18%, mainly due to increasing alternative material portion in dough. In general, fibre is characterised as hydrophilic material, and pasting profiles of flour composites confirmed this experience. During dough leavening, tested samples were differentiated according to maturograph dough resistance; optimal leavening time of wheat-linseed fibre dough was shorter than control. Regardless described modifications in dough machinability, specific volumes of bread buns were similar though whole sample set. A weak worsening of buns vaulting reflected a partial dilution of dough gluten skeleton. Cut-off biscuits were characterised by gradually lowering spread ratio, correspondingly to elevated dough elasticity. Laboratory prepared elbow-pasta have the same cooking time as the control (8.0 min, and data variation could not be attributed to linseed fibre or addition level. All three cereal products were found to have acceptable sensory profiles. PCA method verified partial lowering of

[Research on evaluation of water quality of Beijing urban stormwater runoff].

Science.gov (United States)

Hou, Pei-Qiang; Ren, Yu-Fen; Wang, Xiao-Ke; Ouyang, Zhi-Yun; Zhou, Xiao-Ping

2012-01-01

The natural rainwater and stormwater runoff samples from three underlying surfaces (rooftop, campus road and ring road) were sampled and analyzed from July to October, 2010 in Beijing. Eight rainfall events were collected totally and thirteen water quality parameters were measured in each event. Grey relationship analysis and principal component analysis were applied to assess composite water quality and identify the main pollution sources of stormwater runoff. The results show that the composite water quality of ring road runoff is mostly polluted, and then is rooftop runoff, campus road runoff and rainwater, respectively. The composite water quality of ring road runoff is inferior to V class of surface water, while rooftop runoff, campus road runoff and rainwater are in II class of surface water. The mean concentration of TN and NH4(+)-N in rainwater and runoff is 5.49-11.75 mg x L(-1) and 2.90-5.67 mg x L(-1), respectively, indicating that rainwater and runoff are polluted by nitrogen (N). Two potential pollution sources are identified in ring road runoff: (1) P, SS and organic pollutant are possibly related to debris which is from vehicle tyre and material of ring road; (2) N and dissolved metal have relations with automobile exhaust emissions and bulk deposition.

Effects of mining activities on evolution of water quality of karst waters in Midwestern Guizhou, China: evidences from hydrochemistry and isotopic composition.

Science.gov (United States)

Li, Xuexian; Wu, Pan; Han, Zhiwei; Zha, Xuefang; Ye, Huijun; Qin, Yingji

2018-01-01

Zhijin coal-mining district, located in Midwestern Guizhou Province, has been extensively exploited for several decades. The discharge of acid mine drainage (AMD) has constituted a serious threat to local water environmental quality, which greatly affected the normal use of local people. The Permian limestone aquifer is the essential potable water supply for local people, which covered under the widely distributed coal seams. To investigate the origin of the water, the evolutionary processes, and the sources of dissolved sulfate in the karst waters, the mine water, surface water, and groundwater near the coal mines were sampled for stable isotopes (H, O, and S) and conventional hydrochemical analysis. The results of hydrochemistry and isotopic composition indicate that the regional surface water and partial karst groundwater are obviously affected by coal-mining activities, which is mainly manifested in the increase of water solute concentration and the change of hydrochemical types. The isotopic composition of δ 2 H H2O and δ 18 O H2O indicates that the major recharge source of surface water and the groundwater is atmospheric precipitation and that it is influenced obviously by evaporation in the recharge process. The surface water is mainly controlled by the oxidation of pyrite, as well as the dissolution of carbonate rocks, whereas that of natural karst waters is influenced by the dissolution of carbonate rocks. The resulting δ 34 S SO4 values suggest that the dissolved sulfate source in the surface water is mainly pyrite oxidation but atmospheric precipitation for the karst groundwater. Given the similar chemistry and isotopic composition between surface water and partial groundwater, it is reasonable to assume that most of the dissolved sulfate source in part of the groundwater was derived through the oxidation of pyrite in the coal. Furthermore, the contamination of the surface water and partial groundwater from the coal seam has occurred distinctly in the

Effects of dietary lipid source on growth, digestibility and tissue fatty acid composition of Heterobranchus longifilis fingerlings

Directory of Open Access Journals (Sweden)

David Friday Apata

2012-04-01

Full Text Available One of the major problems facing aquaculture is the inadequate supply of fish oil mostly used for fish feed manufacturing. The continued growth in aquaculture production cannot depend on this finite feed resources, therefore, it is imperative that cheap and readily available substitutes that do not compromise fish growth and fillet quality be found. To achieve this, a 12-week feeding trial with Heterobranchus longifilis fed diets differing in lipid source was conducted. Diets were supplemented with 6% lipid as fish oil, soybean oil, palm oil, coconut oil, groundnut oil and melon seed oil. Triplicate groups of 20 H. longifilis were fed the experimental diets two times a day to apparent satiation, over 84 days. Growth, digestibility, and muscle fatty acid profile were measured to assess diet effects. At the end of the study, survival, feed intake and hepatosomatic index were similar for fish fed experimental diets. However, weight gain, SGR and FCR of fish fed soybean oil-based diet was significantly reduced. Apparent nutrient digestibility coefficients were significantly lower in fish fed soybean, coconut and groundnut oil-based diets. Fillet and hepatic fatty acid compositions differed and reflected the fatty acid compositions of the diets. Docosahexaenoic acid (22:6n-3, 20:5n-3 and 20:4n-6 were conserved in vegetable oils-based diets fed fish possibly due to synthesis of HUFA from 18:3n-3 and 18:4n-6. Palm oil diet was the least expensive, and had the best economic conversion ratio. The use of vegetable oils in the diets had positive effect on growth and fillet composition of H. longifilis.

Aerosol composition and sources in the central Arctic Ocean during ASCOS

Science.gov (United States)

Chang, R. Y.-W.; Leck, C.; Graus, M.; Müller, M.; Paatero, J.; Burkhart, J. F.; Stohl, A.; Orr, L. H.; Hayden, K.; Li, S.-M.; Hansel, A.; Tjernström, M.; Leaitch, W. R.; Abbatt, J. P. D.

2011-10-01

Measurements of submicron aerosol chemical composition were made over the central Arctic Ocean from 5 August to 8 September 2008 as a part of the Arctic Summer Cloud Ocean Study (ASCOS) using an aerosol mass spectrometer (AMS). The median levels of sulphate and organics for the entire study were 0.051 and 0.055 μ g m-3, respectively. Positive matrix factorisation was performed on the entire mass spectral time series and this enabled marine biogenic and continental sources of particles to be separated. These factors accounted for 33% and 36% of the sampled ambient aerosol mass, respectively, and they were both predominantly composed of sulphate, with 47% of the sulphate apportioned to marine biogenic sources and 48% to continental sources, by mass. Within the marine biogenic factor, the ratio of methane sulphonate to sulphate was 0.25 ± 0.02, consistent with values reported in the literature. The organic component of the continental factor was more oxidised than that of the marine biogenic factor, suggesting that it had a longer photochemical lifetime than the organics in the marine biogenic factor. The remaining ambient aerosol mass was apportioned to an organic-rich factor that could have arisen from a combination of marine and continental sources. In particular, given that the factor does not correlate with common tracers of continental influence, we cannot rule out that the organic factor arises from a primary marine source.

Source Apportionment and Elemental Composition of PM2.5 and PM10 in Jeddah City, Saudi Arabia.

Science.gov (United States)

Khodeir, Mamdouh; Shamy, Magdy; Alghamdi, Mansour; Zhong, Mianhua; Sun, Hong; Costa, Max; Chen, Lung-Chi; Maciejczyk, Polina

2012-07-01

This paper presents the first comprehensive investigation of PM2.5 and PM10 composition and sources in Saudi Arabia. We conducted a multi-week multiple sites sampling campaign in Jeddah between June and September, 2011, and analyzed samples by XRF. The overall mean mass concentration was 28.4 ± 25.4 μg/m 3 for PM2.5 and 87.3 ± 47.3 μg/m 3 for PM10, with significant temporal and spatial variability. The average ratio of PM2.5/PM10 was 0.33. Chemical composition data were modeled using factor analysis with varimax orthogonal rotation to determine five and four particle source categories contributing significant amount of for PM2.5 and PM10 mass, respectively. In both PM2.5 and PM10 sources were (1) heavy oil combustion characterized by high Ni and V; (2) resuspended soil characterized by high concentrations of Ca, Fe, Al, and Si; and (3) marine aerosol. The two other sources in PM2.5 were (4) Cu/Zn source; (5) traffic source identified by presence of Pb, Br, and Se; while in PM10 it was a mixed industrial source. To estimate the mass contributions of each individual source category, the CAPs mass concentration was regressed against the factor scores. Cumulatively, resuspended soil and oil combustion contributed 77 and 82% mass of PM2.5 and PM10, respectively.

Safety quality classification test of the sealed neutron sources used in start-up neutron source rods for Qinshan Nuclear Power Plant

International Nuclear Information System (INIS)

Yao Chunbing; Guo Gang; Chao Jinglan; Duan Liming

1992-01-01

According to the regulations listed in the GB4075, the safety quality classification tests have been carried out for the neutron sources. The test items include temperature, external pressure, impact, vibration and puncture, Two dummy sealed sources are used for each test item. The testing equipment used have been examined and verified to be qualified by the measuring department which is admitted by the National standard Bureau. The leak rate of each tested sample is measured by UL-100 Helium Leak Detector (its minimum detectable leak rate is 1 x 10 -10 Pa·m 3 ·s -1 ). The samples with leak rate less than 1.33 x 10 -8 Pa·m 3 ·s -1 are considered up to the standard. The test results show the safety quality classification class of the neutron sources have reached the class of GB/E66545 which exceeds the preset class

Impacts by point and diffuse micropollutant sources on the stream water quality at catchment scale

DEFF Research Database (Denmark)

Petersen, Mette Fjendbo; Eriksson, Eva; Binning, Philip John

2012-01-01

the stream and analyzed for general water quality parameters, inorganic constituents, pesticides, sulfonamides, chlorinated solvents, BTEXs, and paracetamol and ibuprofen. The latter two groups were not detected. The general water quality showed typical conditions for a stream in western Jutland. Minor...... at the pharmaceutical factory site, the drainage ditch and the waste deposits is similar in composition containing among others sulfonamides and chlorinated solvents (including vinyl chloride). Vinyl chloride concentrations surpassed Danish stream water quality criteria with a factor 10. The largest chemical impact...

Effects of persimmon peel supplementation on pork quality, palatability, fatty acid composition, and cholesterol level

Directory of Open Access Journals (Sweden)

Sang Moo Lee

2016-08-01

Full Text Available Abstract Background The objectives of this study were to investigate the effects of persimmon peel (PPM supplementation on carcass performance, pork quality, eating quality, fatty acid composition, and cholesterol concentration of the porcine longissimus dorsi muscle. Results No adverse effects of PPM supplementation were observed on carcass and meat quality characteristics among the treatment groups (P > 0.05, whereas pork loins from pigs fed a diet supplemented with 0.9 % persimmon peel (T3 showed more tender meat than did pork loins from pigs fed a control diet (P < 0.01, even though no significant difference was observed between the control and T1 group. The T3 group had higher ratio of polyunsaturated fatty acids relative to saturated fatty acids (0.33 vs. 0.28, P < 0.05 and lower total cholesterol concentration (94.4 vs. 99.1 mg/g, P < 0.05 compared to the control group. Persimmon peel appeared to have beneficial effects on fatty acid composition and cholesterol concentration, probably leading to a hypocholesterolemic effect. Conclusions Animal diets fortified with persimmon peel represents an efficient and useful method for improving the nutritional quality of pork without impairing growth performance and eating quality properties.

Composites Similarity Analysis Method Based on Knowledge Set in Composites Quality Control

OpenAIRE

Li Haifeng

2016-01-01

Composites similarity analysis is an important link of composites review, it can not only to declare composites review rechecking, still help composites applicants promptly have the research content relevant progress and avoid duplication. This paper mainly studies the composites similarity model in composites review. With the actual experience of composites management, based on the author’s knowledge set theory, paper analyzes deeply knowledge set representation of composites knowledge, impr...

Estimation of contribution ratios of pollutant sources to a specific section based on an enhanced water quality model.

Science.gov (United States)

Cao, Bibo; Li, Chuan; Liu, Yan; Zhao, Yue; Sha, Jian; Wang, Yuqiu

2015-05-01

Because water quality monitoring sections or sites could reflect the water quality status of rivers, surface water quality management based on water quality monitoring sections or sites would be effective. For the purpose of improving water quality of rivers, quantifying the contribution ratios of pollutant resources to a specific section is necessary. Because physical and chemical processes of nutrient pollutants are complex in water bodies, it is difficult to quantitatively compute the contribution ratios. However, water quality models have proved to be effective tools to estimate surface water quality. In this project, an enhanced QUAL2Kw model with an added module was applied to the Xin'anjiang Watershed, to obtain water quality information along the river and to assess the contribution ratios of each pollutant source to a certain section (the Jiekou state-controlled section). Model validation indicated that the results were reliable. Then, contribution ratios were analyzed through the added module. Results show that among the pollutant sources, the Lianjiang tributary contributes the largest part of total nitrogen (50.43%), total phosphorus (45.60%), ammonia nitrogen (32.90%), nitrate (nitrite + nitrate) nitrogen (47.73%), and organic nitrogen (37.87%). Furthermore, contribution ratios in different reaches varied along the river. Compared with pollutant loads ratios of different sources in the watershed, an analysis of contribution ratios of pollutant sources for each specific section, which takes the localized chemical and physical processes into consideration, was more suitable for local-regional water quality management. In summary, this method of analyzing the contribution ratios of pollutant sources to a specific section based on the QUAL2Kw model was found to support the improvement of the local environment.

Preparation method and quality control of multigamma volume sources with different matrices.

Science.gov (United States)

Listkowska, A; Lech, E; Saganowski, P; Tymiński, Z; Dziel, T; Cacko, D; Ziemek, T; Kołakowska, E; Broda, R

2018-04-01

The aim of the work was to develop new radioactive standard sources based on epoxy resins. The optimal proportions of the components and the homogeneity of the matrices were determined. The activity of multigamma sources prepared in Marinelli beakers was determined with reference to the National Standard of Radionuclides Activity in Poland. The difference of radionuclides activity values determined using calibrated gamma spectrometer and the activity of standard solutions used are in most cases significantly lower than measurement uncertainty limits. Sources production method and quality control procedure have been developed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sources of atmospheric aerosol from long-term measurements (5 years) of chemical composition in Athens, Greece.

Science.gov (United States)

Paraskevopoulou, D; Liakakou, E; Gerasopoulos, E; Mihalopoulos, N

2015-09-15

To identify the sources of aerosols in Greater Athens Area (GAA), a total of 1510 daily samples of fine (PM 2.5) and coarse (PM 10-2,5) aerosols were collected at a suburban site (Penteli), during a five year period (May 2008-April 2013) corresponding to the period before and during the financial crisis. In addition, aerosol sampling was also conducted in parallel at an urban site (Thissio), during specific, short-term campaigns during all seasons. In all these samples mass and chemical composition measurements were performed, the latest only at the fine fraction. Particulate organic matter (POM) and ionic masses (IM) are the main contributors of aerosol mass, equally contributing by accounting for about 24% of the fine aerosol mass. In the IM, nss-SO4(-2) is the prevailing specie followed by NO3(-) and NH4(+) and shows a decreasing trend during the 2008-2013 period similar to that observed for PM masses. The contribution of water in fine aerosol is equally significant (21 ± 2%), while during dust transport, the contribution of dust increases from 7 ± 2% to 31 ± 9%. Source apportionment (PCA and PMF) and mass closure exercises identified the presence of six sources of fine aerosols: secondary photochemistry, primary combustion, soil, biomass burning, sea salt and traffic. Finally, from winter 2012 to winter 2013 the contribution of POM to the urban aerosol mass is increased by almost 30%, reflecting the impact of wood combustion (dominant fuel for domestic heating) to air quality in Athens, which massively started in winter 2013. Copyright © 2015 Elsevier B.V. All rights reserved.

The Papers Printing Quality Complex Assessment Algorithm Development Taking into Account the Composition and Production Technological Features

Science.gov (United States)

Babakhanova, Kh A.; Varepo, L. G.; Nagornova, I. V.; Babluyk, E. B.; Kondratov, A. P.

2018-04-01

Paper is one of the printing system key components causing the high-quality printed products output. Providing the printing companies with the specified printing properties paper, while simultaneously increasing the paper products range and volume by means of the forecasting methods application and evaluation during the production process, is certainly a relevant problem. The paper presents the printing quality control algorithm taking into consideration the paper printing properties quality assessment depending on the manufacture technological features and composition variation. The information system including raw material and paper properties data and making possible pulp and paper enterprises to select paper composition optimal formulation is proposed taking into account the printing process procedure peculiarities of the paper manufacturing with specified printing properties.

Composition of source-sorted municipal organic waste collected in Danish cities

DEFF Research Database (Denmark)

Hansen, Trine Lund; Jansen, Jes La Cour; Spliid, Henrik

2007-01-01

Source-sorted municipal organic waste from different dwelling types in five Danish cities was sampled during one year. The samples were from permanent, full-scale systems or temporary, experimental systems for collection of source-sorted municipal organic waste. Pre-treatment of the organic waste...... prior to biological treatment was used in all cities to remove foreign objects and provide size reduction. All sampling was performed after pre-treatment in order to obtain more homogeneous and representative samples. The sampling included both the pre-treated waste and the reject from the pre......-treatment allowing for estimation of the composition of the original waste. A total of 40 waste samples were chemically characterised with respect to 15 parameters. The waste generally consisted of around 88% VS of which an average of 80% was easily degradable. The average content of N, P and K in the dry matter...

Changes of Groundwater Quality in the Sorrounding Pollution Sources Due to Earthquake Dissaster

Directory of Open Access Journals (Sweden)

Sudarmadji Sudarmadji

2016-05-01

Full Text Available Groundwater is the main domestic water supply of the population of the Yogyakarta Special Region, both in the urban and as well as in the rural area due to its quantity and quality advantages. The rapid population growth has caused an increase of groundwater demand, consequently it is facing some problems to the sustainability of groundwater supply. Lowering of groundwater level has been observed in some places, as well as the degradation of groundwater quality. Earthquake which stroke Yogyakarta on 27 May 2006, damaged buildings and other infrastructures in the area, including roads and bridges. It might also damage the underground structures such as septic tanks, and pipes underneath the earth surface. It might cause cracking of the geologic structures. Furthermore, the damage of underneath infrastructures might create groundwater quality changes in the area. Some complains of local community on lowering and increasing groundwater level and groundwater quality changes were noted. Field observation and investigation were conducted, including collection of groundwater samples close to (the pollution sources. Laboratory analyses indicated that some parameters increased to exceed the drinking water quality standards. The high content of Coli form bacteria possibly was caused by contamination of nearby septic tanks or other pollution sources to the observed groundwater in the dug well.

Chemical composition and source apportionment of PM10 at an urban background site in a high-altitude Latin American megacity (Bogota, Colombia).

Science.gov (United States)

Ramírez, Omar; Sánchez de la Campa, A M; Amato, Fulvio; Catacolí, Ruth A; Rojas, Néstor Y; de la Rosa, Jesús

2018-02-01

Bogota registers frequent episodes of poor air quality from high PM 10 concentrations. It is one of the main Latin American megacities, located at 2600 m in the tropical Andes, but there is insufficient data on PM 10 source contribution. A characterization of the chemical composition and the source apportionment of PM 10 at an urban background site in Bogota was carried out in this study. Daily samples were collected from June 2015 to May 2016 (a total of 311 samples). Organic carbon (OC), elemental carbon (EC), water soluble compounds (SO 4 2- , Cl - , NO 3 - , NH 4 + ), major elements (Al, Fe, Mg, Ca, Na, K, P) and trace metals (V, Cd, Pb, Sr, Ba, among others) were analyzed. The results were interpreted in terms of their variability during the rainy season (RS) and the dry season (DS). The data obtained revealed that the carbonaceous fraction (∼51%) and mineral dust (23%) were the main PM 10 components, followed by others (15%), Secondary Inorganic Compounds (SIC) (11%) and sea salt (0.4%). The average concentrations of soil, SIC and OC were higher during RS than DS. However, peak values were observed during the DS due to photochemical activity and forest fires. Although trace metals represented <1% of PM 10 , high concentrations of toxic elements such as Pb and Sb on RS, and Cu on DS, were obtained. By using a PMF model, six factors were identified (∼96% PM 10 ) including fugitive dust, road dust, metal processing, secondary PM, vehicles exhaust and industrial emissions. Traffic (exhaust emissions + road dust) was the major PM 10 source, accounting for ∼50% of the PM 10 . The results provided novel data about PM 10 chemical composition, its sources and its seasonal variability during the year, which can help the local government to define control strategies for the main emission sources during the most critical periods. Copyright © 2017 Elsevier Ltd. All rights reserved.

THERMAL COMPOSITE COATINGS IMPROVING QUALITY OF TECHNICAL MEANS OF TRANSPORT

Directory of Open Access Journals (Sweden)

Andrzej POSMYK

2015-06-01

Full Text Available The paper presents the thermal properties of composite insulating material designed for producing of technical means of transport. This material can be coated on most of engineering materials. The matrix of this material is an acrylic resin ant non porous ceramic microspheres made of alumina are the reinforcing phase. Thanks to that into the spheres almost vacuum (0,13 Pa dominants and a big amount of spheres pro thickness unit is it possible to achieve low thermal conductivity. Usage of these coatings for producing of cooling cabins on vehicles let us to reduce of fuel for maintain of given temperature. Usage of these coatings in planes flying on high altitudes (temperature up to -60 allows to reduce of fuel consumption for heating. It has an important influence on transport quality and quality costs.

Experimental investigation on water quality standard of Yangtze River water source heat pump.

Science.gov (United States)

Qin, Zenghu; Tong, Mingwei; Kun, Lin

2012-01-01

Due to the surface water in the upper reaches of Yangtze River in China containing large amounts of silt and algae, high content of microorganisms and suspended solids, the water in Yangtze River cannot be used for cooling a heat pump directly. In this paper, the possibility of using Yangtze River, which goes through Chongqing, a city in southwest China, as a heat source-sink was investigated. Water temperature and quality of the Yangtze River in the Chongqing area were analyzed and the performance of water source heat pump units in different sediment concentrations, turbidity and algae material conditions were tested experimentally, and the water quality standards, in particular surface water conditions, in the Yangtze River region that adapt to energy-efficient heat pumps were also proposed. The experimental results show that the coefficient of performance heat pump falls by 3.73% to the greatest extent, and the fouling resistance of cooling water in the heat exchanger increases up to 25.6% in different water conditions. When the sediment concentration and the turbidity in the river water are no more than 100 g/m3 and 50 NTU respectively, the performance of the heat pump is better, which can be used as a suitable river water quality standard for river water source heat pumps.

Chemical composition and source apportionment of aerosol over the Klang valley

International Nuclear Information System (INIS)

Shamsiah Abdul Rahman; Mohd Suhaimi Hamzah; Abdul Khalik Wood; Nazaratul Ashifa Abdullah Salim; Mohd Suhaimi Elias; Eswiza Sanuri

2009-01-01

This paper reports the study of aerosol chemical composition of fine particles (PM 2.5) and possible sources of air pollution over the Klang Valley, Kuala Lumpur, based on the samples collected for a period of 6 years from July 2000 to Jun 2006. Samples collected were measured for mass, black carbon and elemental content of Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Br and Pb. The fine aerosol mass concentration ranged from 11 - 110 ?g/m3. Black carbon is the major component of the fine aerosol with the weight fraction of 20%, whilst S is the major elemental content with the weight fraction about 5% as relative to the fine particle mass. The factor analysis method, positive matrix factorization (PMF) was then used to confirm the possible sources. The result of PMF analysis produced five-factor sources that contribute to the fine particles in the Klang Valley area. The five factors represent sea spray, industry, motor vehicles, smoke and soil. Motor vehicle is the main source of particulates in the area, with an average contribution of 51% of the fine mass concentration, followed by industry, smoke, sea spray and soil, with average contribution of 28%, 14%, 3.6% and 2.1%, respectively. (Author)

Split Nitrogen Application Improves Wheat Baking Quality by Influencing Protein Composition Rather Than Concentration.

Science.gov (United States)

Xue, Cheng; Auf'm Erley, Gunda Schulte; Rossmann, Anne; Schuster, Ramona; Koehler, Peter; Mühling, Karl-Hermann

2016-01-01

The use of late nitrogen (N) fertilization (N application at late growth stages of wheat, e.g., booting, heading or anthesis) to improve baking quality of wheat has been questioned. Although it increases protein concentration, the beneficial effect on baking quality (bread loaf volume) needs to be clearly understood. Two pot experiments were conducted aiming to evaluate whether late N is effective under controlled conditions and if these effects result from increased N rate or N splitting. Late N fertilizers were applied either as additional N or split from the basal N at late boot stage or heading in the form of nitrate-N or urea. Results showed that late N fertilization improved loaf volume of wheat flour by increasing grain protein concentration and altering its composition. Increasing N rate mainly enhanced grain protein quantitatively. However, N splitting changed grain protein composition by enhancing the percentages of gliadins and glutenins as well as certain high molecular weight glutenin subunits (HMW-GS), which led to an improved baking quality of wheat flour. The late N effects were greater when applied as nitrate-N than urea. The proportions of glutenin and x-type HMW-GS were more important than the overall protein concentration in determining baking quality. N splitting is more effective in improving wheat quality than the increase in the N rate by late N, which offers the potential to cut down N fertilization rates in wheat production systems.

Split nitrogen application improves wheat baking quality by influencing protein composition rather than concentration

Directory of Open Access Journals (Sweden)

Cheng eXue

2016-06-01

Full Text Available The use of late nitrogen (N fertilization (N application at late growth stages of wheat, e.g. booting, heading or anthesis to improve baking quality of wheat has been questioned. Although it increases protein concentration, the beneficial effect on baking quality (bread loaf volume needs to be clearly understood. Two pot experiments were conducted aiming to evaluate whether late N is effective under controlled conditions and if these effects result from increased N rate or N splitting. Late N fertilizers were applied either as additional N or split from the basal N at late boot stage or heading in the form of nitrate-N or urea. Results showed that late N fertilization improved loaf volume of wheat flour by increasing grain protein concentration and altering its composition. Increasing N rate mainly enhanced grain protein quantitatively. However, N splitting changed grain protein composition by enhancing the percentages of gliadins and glutenins as well as certain high molecular weight glutenin subunits (HMW-GS, which led to an improved baking quality of wheat flour. The late N effects were greater when applied as nitrate-N than urea. The proportions of glutenin and x-type HMW-GS were more important than the overall protein concentration in determining baking quality. N splitting is more effective in improving wheat quality than the increase in the N rate by late N, which offers the potential to cut down N fertilization rates in wheat production systems.

Impact of traffic volume and composition on the air quality and pedestrian exposure in urban street canyon

Science.gov (United States)

Rakowska, Agata; Wong, Ka Chun; Townsend, Thomas; Chan, Ka Lok; Westerdahl, Dane; Ng, Simon; Močnik, Griša; Drinovec, Luka; Ning, Zhi

2014-12-01

Vehicle emissions are identified as a major source of air pollution in metropolitan areas. Emission control programs in many cities have been implemented as part of larger scale transport policy interventions to control traffic pollutants and reduce public health risks. These interventions include provision of traffic-free and low emission zones and congestion charging. Various studies have investigated the impact of urban street configurations, such as street canyon in urban centers, on pollutants dispersion and roadside air quality. However, there are few investigations in the literature to study the impact of change of fleet composition and street canyon effects on the on-road pollutants concentrations and associated roadside pedestrian exposure to the pollutants. This study presents an experimental investigation on the traffic related gas and particle pollutants in and near major streets in one of the most developed business districts in Hong Kong, known as Central. Both street canyon and open roadway configurations were included in the study design. Mobile measurement techniques were deployed to monitor both on-road and roadside pollutants concentrations at different times of the day and on different days of a week. Multiple traffic counting points were also established to concurrently collect data on traffic volume and fleet composition on individual streets. Street canyon effects were evident with elevated on-road pollutants concentrations. Diesel vehicles were found to be associated with observed pollutant levels. Roadside black carbon concentrations were found to correlate with their on-road levels but with reduced concentrations. However, ultrafine particles showed very high concentrations in roadside environment with almost unity of roadside/on-road ratios possibly due to the accumulation of primary emissions and secondary PM formation. The results from the study provide useful information for the effective urban transport design and bus route

Effect of supplementing finishing pigs with different sources of chromium on performance and meat quality

Directory of Open Access Journals (Sweden)

Louise Manha Peres

2014-07-01

Full Text Available The objective was to evaluate the dietary supplementation of different sources of chromium (inorganic: chromium sulfate and chelated: chromium-methionine during the finishing period of pigs to obtain improvements in the animal performance, and carcass and meat quality. The statistical design was randomized blocks, where 44 barrows, with an initial weight 60.49±5.12 kg, were divided into four blocks (heavier, heavy, light and lighter according to initial weight. The experimental diets were isoenergetic and isonutrient, except for the chromium level. The treatments were divided as follows: control (without chromium, control + 200 ppb of inorganic chromium (chromium sulfate, and control + 200 ppb of chelated chromium (chromium-methionine. In the performance measures, the stall was considered the experimental unit and in the blood parameters, carcass and meat evaluations each animal constituted the experimental unit. Animals were slaughtered when they reached the final average weight of 107.23±5.23 kg. Blood samples were collected and tested for blood parameters (cholesterol, triglycerides and glucose as well as carcass quality (hot and cold weights, yield, loin-eye area, muscle depth and backfat thickness and meat quality (initial and final pH, drip loss, color, chemical composition and lipid oxidation parameters. Chromium-methionine supplementation provides a greater daily weight gain only compared with the animals that are not supplemented with chromium, because feed conversion is better as compared with the other treatments. After 24 hours of storage, the meat from pigs supplemented either with chromium-methionine or with chromium sulfate presents lower lipid oxidation than that from non-supplemented animals. However, after three days of storage, only chromim-methionine is effective in reducing lipid oxidation.

Considering the future of anthropogenic gas-phase organic compound emissions and the increasing influence of non-combustion sources on urban air quality

Science.gov (United States)

Khare, Peeyush; Gentner, Drew R.

2018-04-01

Decades of policy in developed regions has successfully reduced total anthropogenic emissions of gas-phase organic compounds, especially volatile organic compounds (VOCs), with an intentional, sustained focus on motor vehicles and other combustion-related sources. We examine potential secondary organic aerosol (SOA) and ozone formation in our case study megacity (Los Angeles) and demonstrate that non-combustion-related sources now contribute a major fraction of SOA and ozone precursors. Thus, they warrant greater attention beyond indoor environments to resolve large uncertainties in their emissions, oxidation chemistry, and outdoor air quality impacts in cities worldwide. We constrain the magnitude and chemical composition of emissions via several bottom-up approaches using chemical analyses of products, emissions inventory assessments, theoretical calculations of emission timescales, and a survey of consumer product material safety datasheets. We demonstrate that the chemical composition of emissions from consumer products as well as commercial and industrial products, processes, and materials is diverse across and within source subcategories. This leads to wide ranges of SOA and ozone formation potentials that rival other prominent sources, such as motor vehicles. With emission timescales from minutes to years, emission rates and source profiles need to be included, updated, and/or validated in emissions inventories with expected regional and national variability. In particular, intermediate-volatility and semi-volatile organic compounds (IVOCs and SVOCs) are key precursors to SOA, but are excluded or poorly represented in emissions inventories and exempt from emissions targets. We present an expanded framework for classifying VOC, IVOC, and SVOC emissions from this diverse array of sources that emphasizes a life cycle approach over longer timescales and three emission pathways that extend beyond the short-term evaporation of VOCs: (1) solvent evaporation, (2

Chemical and Microbial Quality of Groundwater in Siloam Village, Implications to Human Health and Sources of Contamination

Directory of Open Access Journals (Sweden)

John Ogony Odiyo

2018-02-01

Full Text Available Due to inaccessibility of potable water, rural communities drill boreholes within their homesteads despite vulnerability to groundwater contamination and associated health risks. This study assessed the quality of groundwater, identified potential sources of contamination and potential human health risks in Siloam Village, South Africa. Statistical difference between similar water quality parameters at different sites was determined at a significance level (α of 0.05. Water quality parameters with serious potential health effects on human beings were correlated with selected water quality parameters to understand the nature of correlation and possible sources of contamination. Fluorides and nitrates had excessively high concentrations associated with tooth damage and pronounced skeletal fluorosis, and methaemoglobinaemia in infants and mucous membrane irritation in adults, respectively. There were statistically significant differences between means of most water quality parameters. Contrasting correlation of fluoride with calcium and pH indicated the need to further identify local sources and fluoride control mechanisms. Correlation of nitrate with chloride mostly indicated that faecal contamination is the potential source of high nitrates in groundwater. This requires further verification. Presence of total coliforms and E. coli in most boreholes indicated potential presence of faecal contamination. The need to educate borehole owners’ on possible strategies to minimise groundwater pollution was identified.

Organic compositions of lacustrine source rocks in Jiyang super-depression and its implication to petroleum geology

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The compositions of organic matter in four immature source rocks from Tertiary strata of Jiyang super-depression, the most typical continental rift subsidence basin in East China, have been studied by different extracting methods with CHCl3, MAC and CS2/NMP, respectively. The results suggest that there are great differences among the chemical compositions of organic matter in the source rocks derived from different depositional environments. About 79% of all the organic matter exists by non- covalent bond in the Es4 source rocks which were deposited under the saline lacustrine, indicating that its organic matter is not the real kerogen, but mainly composed of soluble organic matter which is easy to generate hydrocarbon at lower temperature. This is why the immature oils were derived from Es4 source rocks in Dongying depression. In contrast, around 60% of organic matter exists by covalent bond in Es3 source rocks which were deposited under the deep brackish-fresh lacustrine, showing that Es3 source rocks are mainly composed of kerogen producing mature hydrocarbon at higher temperature. The thermal simulation experiments, upon the remaining solid source rocks which were sequentially extracted by the three solvents, have been carried out. The chloroform extracts from the simulation product have been compared with the other three solvent extracts gained at room temperature. It is obvious that remarkable odd/even predominance (OEP) is mainly the characteristic of soluble organic matter; phytane mostly exists in the soluble organic matter by means of non-covalent bonds and characteristics of soluble organic matter are similar to these in immature oils produced in Jiyang super-depression.

Influence of preconsolidation on consolidation quality after stamp forming of C/PEEK composites

Science.gov (United States)

Slange, T. K.; Warnet, L.; Grouve, W. J. B.; Akkerman, R.

2016-10-01

Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. Currently, expensive autoclave and press consolidation are used to preconsolidate blanks. This study investigates the influence of preconsolidation on final consolidation quality after stamp forming and explores the potential of alternative blank manufacturing methods that could reduce part costs. Blanks were manufactured using various blank manufacturing methods and subsequently were stamp formed. The consolidation quality both before and after stamp forming was compared, where the focus was on void content as the main measure for consolidation quality. The void content was characterized through thickness and density measurements, as well as by microscopy analysis. Results indicate that preconsolidation quality does have an influence on the final consolidation quality. This is due to the severe deconsolidation and limited reconsolidation during stamp forming. Nevertheless, the potential of automated fiber placement and ultrasonic spot welding as alternative blank manufacturing methods was demonstrated.

Development of quality assurance programme for prescribed ionizing radiation source testing. Recommendations

International Nuclear Information System (INIS)

1999-01-01

The document gives guidance to those applying for licence to perform ionizing radiation source acceptance tests and long-term stability tests and provides information which should be known when introducing quality assurance systems in compliance with legislative requirements. It is envisaged that this document ('Recommendations') will form a basis for final Safety Guides to be issued by the State Office for Nuclear Safety, the Czech nuclear regulatory authority. The setup of the publication is as follows. Part I gives a glossary of basic terms in quality systems. Part 2 explains quality system principles, paying special attention to radiation safety issues, and describes the structure and scope of quality system documentation. Part 3 explains the individual elements of the quality system and gives practical examples. Part 4 deals with the quality assurance programme; using instructions and practical examples, this part shows how the quality system elements should be applied to long-time stability testing and acceptance testing. A model structure of 2nd degree documentation (guidelines) and a model testing protocol are given in annexes. (P.A.)

A new test phantom with different breast tissue compositions for image quality assessment in conventional and digital mammography

International Nuclear Information System (INIS)

Pachoud, Marc; Lepori, D; Valley, Jean-Francois; Verdun, Francis R

2004-01-01

Our objective is to describe a new test phantom that permits the objective assessment of image quality in conventional and digital mammography for different types of breast tissue. A test phantom, designed to represent a compressed breast, was made from tissue equivalent materials. Three separate regions, with different breast tissue compositions, are used to evaluate low and high contrast resolution, spatial resolution and image noise. The phantom was imaged over a range of kV using a Contour 2000 (Bennett) mammography unit with a Kodak MinR 2190-MinR L screen-film combination and a Senograph 2000D (General Electric) digital mammography unit. Objective image quality assessments for different breast tissue compositions were performed using the phantom for conventional and digital mammography. For a similar mean glandular dose (MGD), the digital system gives a significantly higher contrast-to-noise ratio (CNR) than the screen-film system for 100% glandular tissue. In conclusion, in mammography, a range of exposure conditions is used for imaging because of the different breast tissue compositions encountered clinically. Ideally, the patient dose-image quality relationship should be optimized over the range of exposure conditions. The test phantom presented in this work permits image quality parameters to be evaluated objectively for three different types of breast tissue. Thus, it is a useful tool for optimizing the patient dose-image quality relationship

Composite quality of care scores, electronic health record maturity models, and their associations; preliminary literature review results

NARCIS (Netherlands)

Joukes, Erik; de Keizer, Nicolette; Cornet, Ronald

2013-01-01

To accurately assess the association between the use of EHR systems and the quality of healthcare we need (composite) measures for quality of healthcare, and a model to measure the maturity of the EHR. This Medline-based literature study therefore focussed on three topics; (1) methods to compose a

Using nitrogen concentration and isotopic composition in lichens to spatially assess the relative contribution of atmospheric nitrogen sources in complex landscapes

International Nuclear Information System (INIS)

Pinho, P.; Barros, C.; Augusto, S.; Pereira, M.J.

2017-01-01

Reactive nitrogen (Nr) is an important driver of global change, causing alterations in ecosystem biodiversity and functionality. Environmental assessments require monitoring the emission and deposition of both the amount and types of Nr. This is especially important in heterogeneous landscapes, as different land-cover types emit particular forms of Nr to the atmosphere, which can impact ecosystems distinctively. Such assessments require high spatial resolution maps that also integrate temporal variations, and can only be feasibly achieved by using ecological indicators. Our aim was to rank land-cover types according to the amount and form of emitted atmospheric Nr in a complex landscape with multiple sources of N. To do so, we measured and mapped nitrogen concentration and isotopic composition in lichen thalli, which we then related to land-cover data. Results suggested that, at the landscape scale, intensive agriculture and urban areas were the most important sources of Nr to the atmosphere. Additionally, the ocean greatly influences Nr in land, by providing air with low Nr concentration and a unique isotopic composition. These results have important consequences for managing air pollution at the regional level, as they provide critical information for modeling Nr emission and deposition across regional as well as continental scales. - Highlights: • Which land-cover types are reactive nitrogen sources or sinks at a landscape level? • Nitrogen concentration and isotopic composition were analyzed in lichens. • This allowed determination of the main nitrogen sources: agricultural and urban areas. • Marine sources provided persistent low concentrations of reactive nitrogen. • The typical signature of each source was also determined. - Reactive-nitrogen concentration and isotopic composition in lichens were used to rank Nr sources at a landscape level.

WATER QUALITY INDEX FOR ASSESSMENT OF DRINKING WATER SOURCES FROM MEDIAŞ TOWN, SIBIU COUNTY

Directory of Open Access Journals (Sweden)

ROŞU CRISTINA

2014-03-01

Full Text Available The purpose of this study was to evaluate the drinking water sources quality from Mediaş Town, Sibiu County. In November 2013, 6 water samples were taken from different drinking water sources and each water sample was analysed to determinate physico-chemical parameters (using a portable multiparameter WTW 320i major ions (using DIONEX ICS1500 ion chromatograph and heavy metals (using Atomic Absorption Spectrophotometer model ZENIT 700 Analytik Jena. The investigated physico-chemical parameters were: temperature, salinity, electrical conductivity (EC, pH, total dissolved solids (TDS and redox potential (ORP. The analysed major ions were: lithium (Li+, sodium (Na+, potassium (K+, magnesium (Mg2+, calcium (Ca2+, fluoride( F-, chloride (Cl-, bromide (Br-, nitrite (NO2-, nitrate (NO3-, phosphate (PO43- and sulphate (SO42-. The investigated heavy metals were: lead (Pb, zinc (Zn, cooper (Cu, iron (Fe, cadmium (Cd, nickel (Ni, chromium (Cr and arsenic (As. The Water Quality Index (WQI was calculated using the analysed water quality parameters and it ranged from 76 (very poor water quality to 375 (unsuitable for drinking.

Dietary energy source affecting fat deposition mechanism, muscle fiber metabolic and overall meat quality

Directory of Open Access Journals (Sweden)

M. Al-Hijazeen

2017-03-01

Full Text Available A study was conducted to investigate the effect of two dietary energy sources, soy bean oil, and sucrose on regulatory mechanisms of meat preservation. Twenty one day-old Hubbard commercial broilers were randomly allocated into two dietary treatment groups with six replicates per treatment, and four broilers per replicate. All birds were coded for the influence of energy source: fat based diet (FD, and sugar based diet (SD. Formulated grower diets were isonitrogenous and isocaloric. The chickens were slaughtered and then boneless, skinless ground chicken tight meat was prepared. Both raw and cooked meats were analyzed for lipid and protein oxidation, and sensory panel evaluation. In addition, meat from the small muscles of the raw thigh was used to evaluate other meat quality characteristics. Proximate analyses showed no significant differences between both dietary treatments on protein, ash and moisture percentage values. Meat samples of the group that was fed FD showed higher significant values of both TBARS and total carbonyl at day 7 of storage time. However, samples of the second group (Fed SD showed lower values of both ultimate pH and water separation % using raw thigh meat. The effect of FD treatment on the meat composition appeared clearly especially on fat percentage content. In addition, meat samples obtained from chickens fed SD showed better significant values of the overall acceptability attribute. According to the current findings, sucrose could be an excellent alternative to oil in dietary broilers which improved the meat preservation bio-system, and post-mortem storage stability.

LED Lighting – Modification of Growth, Metabolism, Yield and Flour Composition in Wheat by Spectral Quality and Intensity

Directory of Open Access Journals (Sweden)

István Monostori

2018-05-01

Full Text Available The use of light-emitting diode (LED technology for plant cultivation under controlled environmental conditions can result in significant reductions in energy consumption. However, there is still a lack of detailed information on the lighting conditions required for optimal growth of different plant species and the effects of light intensity and spectral composition on plant metabolism and nutritional quality. In the present study, wheat plants were grown under six regimens designed to compare the effects of LED and conventional fluorescent lights on growth and development, leaf photosynthesis, thiol and amino acid metabolism as well as grain yield and flour quality of wheat. Benefits of LED light sources over fluorescent lighting were manifested in both yield and quality of wheat. Elevated light intensities made possible with LEDs increased photosynthetic activity, the number of tillers, biomass and yield. At lower light intensities, blue, green and far-red light operated antagonistically during the stem elongation period. High photosynthetic activity was achieved when at least 50% of red light was applied during cultivation. A high proportion of blue light prolonged the juvenile phase, while the shortest flowering time was achieved when the blue to red ratio was around one. Blue and far-red light affected the glutathione- and proline-dependent redox environment in leaves. LEDs, especially in Blue, Pink and Red Low Light (RedLL regimens improved flour quality by modifying starch and protein content, dough strength and extensibility as demonstrated by the ratios of high to low molecular weight glutenins, ratios of glutenins to gliadins and gluten spread values. These results clearly show that LEDs are efficient for experimental wheat cultivation, and make it possible to optimize the growth conditions and to manipulate metabolism, yield and quality through modification of light quality and quantity.

Controlling composition and color characteristics of Monascus pigments by pH and nitrogen sources in submerged fermentation.

Science.gov (United States)

Shi, Kan; Song, Da; Chen, Gong; Pistolozzi, Marco; Wu, Zhenqiang; Quan, Lei

2015-08-01

Submerged fermentations of Monascus anka were performed with different nitrogen sources at different pH in 3 L bioreactors. The results revealed that the Monascus pigments dominated by different color components (yellow pigments, orange pigments or red pigments) could be selectively produced through pH control and nitrogen source selection. A large amount of intracellular pigments dominated by orange pigments and a small amount of water-soluble extracellular yellow pigments were produced at low pH (pH 2.5 and 4.0), independently of the nitrogen source employed. At higher pH (pH 6.5), the role of the nitrogen source became more significant. In particular, when ammonium sulfate was used as nitrogen source, the intracellular pigments were dominated by red pigments with a small amount of yellow pigments. Conversely, when peptone was used, intracellular pigments were dominated by yellow pigments with a few red pigments derivatives. Neither the presence of peptone nor ammonium sulfate promoted the production of intracellular orange pigments while extracellular pigments with an orangish red color were observed in both cases, with a higher yield when peptone was used. Two-stage pH control fermentation was then performed to improve desirable pigments yield and further investigate the effect of pH and nitrogen sources on pigments composition. These results provide a useful strategy to produce Monascus pigments with different composition and different color characteristics. Copyright © 2015 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Access to What? Creating a Composite Measure of Educational Quantity and Educational Quality for 11 African Countries

Science.gov (United States)

Spaull, Nicholas; Taylor, Stephen

2015-01-01

The aim of the current study is to create a composite statistic of educational quantity and educational quality by combining household data (Demographic and Health Survey) on grade completion and survey data (Southern and Eastern African Consortium for Monitoring Educational Quality) on cognitive outcomes for 11 African countries: Kenya, Lesotho,…

Using trace element content and lead isotopic composition to assess sources of PM in Tijuana, Mexico

Science.gov (United States)

Salcedo, D.; Castro, T.; Bernal, J. P.; Almanza-Veloz, V.; Zavala, M.; González-Castillo, E.; Saavedra, M. I.; Perez-Arvízu, O.; Díaz-Trujillo, G. C.; Molina, L. T.

2016-05-01

PM2.5 samples were collected at two urban sites (Parque Morelos (PQM) and CECyTE (CEC)) in Tijuana during the Cal-Mex campaign from May 24 to June 5, 2010. Concentration of trace elements (Mg, Al, Ti, V, Mn, Fe, Co, Ni, Zn, Cu, Ga, As, Se, Rb, Sr, Mo, Cd, Sn, Sb, Ba, La, Ce, and Pb), and Pb isotopic composition were determined in order to study the sources of PM impacting each site. Other chemical analysis (gravimetric, elemental and organic carbon (EC/OC), and polycyclic aromatic hydrocarbons (PAHs)), were also performed. Finally, back-trajectories were calculated to facilitate the interpretation of the chemical data. Trace elements results show that CEC is a receptor site affected by mixed regional sources: sea salt, mineral, urban, and industrial. On the other hand, PQM seems to be impacted mainly by local sources. In particular, Pb at CEC is of anthropogenic, as well as crustal origin. This conclusion is supported by the lead isotopic composition, whose values are consistent with a combination of lead extracted from US mines, and lead from bedrocks in the Mexican Sierras. Some of the time variability observed can be explained using the back-trajectories.

Heterogeneity of the Caribbean plateau mantle source: Sr, O and He isotopic compositions of olivine and clinopyroxene from Gorgona Island

Science.gov (United States)

Révillon, S.; Chauvel, C.; Arndt, N. T.; Pik, R.; Martineau, F.; Fourcade, S.; Marty, B.

2002-12-01

The composition of the mantle plumes that created large oceanic plateaus such as Ontong Java or the Caribbean is still poorly known. Geochemical and isotopic studies on accreted portions of the Caribbean plateau have shown that the plume source was heterogeneous and contained isotopically depleted and relatively enriched portions. A distinctive feature of samples from the Caribbean plateau is their unusual Sr isotopic compositions, which, at a given Nd isotopic ratio, are far higher than in samples from other oceanic plateaus. Sr, O and He isotopic compositions of whole rocks and magmatic minerals (clinopyroxene or olivine) separated from komatiites, gabbros and peridotites from Gorgona Island in Colombia were determined to investigate the origin of these anomalously radiogenic compositions. Sequentially leached clinopyroxenes have Sr isotopic compositions in the range 87Sr/ 86Sr=0.70271-0.70352, systematically lower than those of leached and unleached whole rocks. Oxygen isotopic ratios of clinopyroxene vary within the range δ 18O=5.18-5.35‰, similar to that recorded in oceanic island basalts. He isotopic ratios are high ( R/ Ra=8-19). The lower 87Sr/ 86Sr ratios of most of the clinopyroxenes shift the field of the Caribbean plateau in Nd-Sr isotope diagrams toward more 'normal' values, i.e. a position closer to the field defined by mid-ocean ridge basalts and oceanic-island basalts. Three clinopyroxenes have slightly higher 87Sr/ 86Sr ratios that cannot be explained by an assimilation model. The high 87Sr/ 86Sr and variations of 143Nd/ 144Nd are interpreted as a source characteristic. Trace-element ratios, however, are controlled mainly by fractionation during partial melting. We combine these isotopic data in a heterogeneous plume source model that accounts for the diversity of isotopic signatures recorded on Gorgona Island and throughout the Caribbean plateau. The heterogeneities are related to old recycled oceanic lithosphere in the plume source; the high 3

A Micro-Computed Tomography Technique to Study the Quality of Fibre Optics Embedded in Composite Materials

Directory of Open Access Journals (Sweden)

Gabriele Chiesura

2015-05-01

Full Text Available Quality of embedment of optical fibre sensors in carbon fibre-reinforced polymers plays an important role in the resultant properties of the composite, as well as for the correct monitoring of the structure. Therefore, availability of a tool able to check the optical fibre sensor-composite interaction becomes essential. High-resolution 3D X-ray Micro-Computed Tomography, or Micro-CT, is a relatively new non-destructive inspection technique which enables investigations of the internal structure of a sample without actually compromising its integrity. In this work the feasibility of inspecting the position, the orientation and, more generally, the quality of the embedment of an optical fibre sensor in a carbon fibre reinforced laminate at unit cell level have been proven.

Microfocus x-ray imaging of traceable pointlike {sup 22}Na sources for quality control

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, T.; Oda, K.; Sato, Y.; Ito, H.; Masuda, S.; Yamada, T.; Matsumoto, M.; Murayama, H.; Takei, H. [Allied Health Sciences, Kitasato University Kitasato 1-15-1, Minami-ku, Sagamihara-shi, Kanagawa 252-0373 (Japan); Positron Medical Center, Tokyo Metropolitan Institute of Gerontology Sakaecho 35-2, Itabashi-ku, Tokyo 173-0015 (Japan); Advanced Industrial Science and Technology (AIST) Central 2, Umezono 1-1-1, Tsukuba-shi, Ibaraki 305-8568 (Japan); Kanagawa Industrial Technology Center (KITC) Shimoimazumi 705-1, Ebina-shi, Kanagawa 243-0435 (Japan); Japan Radioisotope Association (JRIA) Komagome 2-28-45, Bunkyo-ku, Tokyo 113-8941 (Japan); Molecular Imaging Center, National Institute of Radiological Sciences Anagawa 4-9-1, Inage, Chiba 263-8555 (Japan); Graduate School of Medical Sciences, Kitasato University Kitasato 1-15-1, Minami-ku, Sagamihara-shi, Kanagawa 252-0373 (Japan)

2012-07-15

Purpose: The purpose of this study is to propose a microfocus x-ray imaging technique for observing the internal structure of small radioactive sources and evaluating geometrical errors quantitatively, and to apply this technique to traceable pointlike {sup 22}Na sources, which were designed for positron emission tomography calibration, for the purpose of quality control of the pointlike sources. Methods: A microfocus x-ray imaging system with a focus size of 0.001 mm was used to obtain projection x-ray images and x-ray CT images of five pointlike source samples, which were manufactured during 2009-2012. The obtained projection and tomographic images were used to observe the internal structure and evaluate geometrical errors quantitatively. Monte Carlo simulation was used to evaluate the effect of possible geometrical errors on the intensity and uniformity of 0.511 MeV annihilation photon pairs emitted from the sources. Results: Geometrical errors were evaluated with sufficient precision using projection x-ray images. CT images were used for observing the internal structure intuitively. As a result, four of the five examined samples were within the tolerance to maintain the total uncertainty below {+-}0.5%, given the source radioactivity; however, one sample was found to be defective. Conclusions: This quality control procedure is crucial and offers an important basis for using the pointlike {sup 22}Na source as a basic calibration tool. The microfocus x-ray imaging approach is a promising technique for visual and quantitative evaluation of the internal geometry of small radioactive sources.

The Water Quality Study and Sources of Pollution in Alur Ilmu, UKM

International Nuclear Information System (INIS)

Nurul Afina Abd Mutalib; Othman Abdul Karim

2015-01-01

The Alur Ilmu UKM is a large storm water channel that serves to store water and flows into Langat River. The primary objective of this study are to identify the water quality and pollution levels, the sources of which may cause pollution and to measures the control pollution that occurs in the area. Water sampling was carried out in order to determine the quality of water. The sampling water was taken during no-rain and after rainfall. The area includes UKM Forest Reserve (Hutan Pendidikan Alam - HPA), Student Cafeteria (Teres Eko Niaga), Restaurant of Fakulti Sains dan Teknologi (FST), Student Centre (Pusanika), Fakulti Pendidikan Islam (FPI) and UKM Mosque. Eight water quality parameters for example consisting of Biochemical Oxygen Demand (BOD), Chemical Oxygen Demand (COD), pH, Turbidity, Total Suspended Solids (TSS), Total Kjeldahl Nitrogen (TKN), Temperature, Oil and Grease were measured. The results shows that the water quality are in a class III and IV according to Water quality Index (WQI) and the water meet the standard B that set out in the Regulations of the Environmental Quality (Sewage and Effluent). (author)

Aerosol composition and its sources at the King Sejong Station, Antarctic peninsula

Science.gov (United States)

Mishra, Vinit K.; Kim, Ki-Hyun; Hong, Sungmin; Lee, Khanghyun

The annual cycles of major metals and ions in suspended particulate matters (SPM) have been investigated at a costal site of the Antarctic Peninsula in order to elucidate temporal variations as well as major source processes responsible for their formation. The measurements had been performed from January 2000 to December 2001 at the Korean Antarctic research station, 'King Sejong' (62°13' S, 58°47' W). The observed time series of important aerosol components showed clear seasonal variation patterns, while the mean elemental concentrations (e.g., 1875 (Al), 10.3 (Ba), 0.3 (Bi), 1.3 (Cd), 1.7 pg m -3 (Co)) were generally compatible with those reported previously. The presence of high EF values with respect to both mean crustal and seawater composition (such as Bi, Cd, Cr, Cu, Ni, V, and Zn), however, suggests a possibly important role of anthropogenic processes in this remote site. In contrast, the concentrations of ionic species were not clearly distinguishable from those of other Antarctic sites; but the consideration of ionic mass balance between cations and anions pointed out the uniqueness of their source/sink processes in the study area. The major source processes of those aerosol components were also investigated using a series of statistical analyses. The overall results of our study indicated the dominance of several processes (or sources) such as sea-salt emission, secondary aerosol formation, and anthropogenic pollution from both local and distant sources.

Quality assurance of HDR 192Ir sources using a Fricke dosimeter.

Science.gov (United States)

Austerlitz, C; Mota, H; Almeida, C E; Allison, R; Sibata, C

2007-04-01

A prototype of a Fricke dosimetry system consisting of a 15 x 15 x 15 cm3 water phantom made of Plexiglas and a 11.3-ml Pyrex balloon fitted with a 0.2 cm thick Pyrex sleeve in its center was created to assess source strength and treatment planning algorithms for use in high dose rate (HDR) 192Ir afterloading units. In routine operation, the radioactive source is positioned at the end of a sleeve, which coincides with the center of the spherical balloon that is filled with Fricke solution, so that the solution is nearly isotropically irradiated. The Fricke system was calibrated in terms of source strength against a reference well-type ionization chamber, and in terms of radial dose by means of an existing algorithm from the HDR's treatment planning system. Because the system is based on the Fricke dosimeter itself, for a given type and model of 192Ir source, the system needs initial calibration but no recalibration. The results from measurements made over a 10 month period, including source decay and source substitutions, have shown the feasibility of using such a system for quality control (QC) of HDR afterloading equipment, including both the source activity and treatment planning parameters. The benefit of a large scale production and the use of this device for clinical HDR QC audits via mail are also discussed.

California State Implementation Plan; Butte County Air Quality Management District; New Source Review (NSR) Permitting Program

Science.gov (United States)

EPA is proposing to approve a revision to the Butte County Air Quality Management District (BCAQMD) portion of the California SIP concerning the District's New Source Review (NSR) permitting program for new and modified sources of air pollution.

Source segregation of food waste in office areas: Factors affecting waste generation rates and quality

DEFF Research Database (Denmark)

Edjabou, Vincent Maklawe Essonanawe; Boldrin, Alessio; Scheutz, Charlotte

2015-01-01

Existing legislation mandates that the amount of waste being recycled should be increased. Among others, in its Resource Strategy Plan, the Danish Government decided that at least 60% of food waste generated by the service sector, including in office areas, should be source-sorted and collected...... separately by 2018. To assess the achievability of these targets, source-sorted food waste and residual waste from office areas was collected and weighed on a daily basis during 133 working days. Waste composition analyses were conducted every week to investigate the efficiency of the source-sorting campaign...... and the purity of the source-sorted food waste. The moisture content of source-sorted food waste and residual waste fractions, and potential methane production from source-sorted food waste, was also investigated.Food waste generation equated to 23. ±. 5. kg/employee/year, of which 20. ±. 5. kg...

Amino acid composition of some Mexican foods.

Science.gov (United States)

Morales de León, Josefina; Camacho, M Elena; Bourges, Héctor

2005-06-01

Knowledge of the amino acid composition of foods is essential to calculate their chemical score, which is used to predict protein quality of foods and diets. Though amino acid composition of many foods is reasonably well established, better knowledge is needed on native foods consumed in different regions and countries. This paper presents the amino acid composition of different presentations of raw and processed foods produced and consumed in Mexico. The amino acid composition was determined using Beckman amino acid analyzers (models 116 and 6300). Tryptophan was determined using the Spies and Chambers method. Of the different foods analyzed, some comments are made on native or basic foods in Mexico: Spirulin, where lysine is the limiting amino acid, with a chemical score of 67%, is a good source of tryptophan (1.16g/16 gN); amaranth contains high levels of sulphur amino acids (4.09 to 5.34 g/16gN), with a protein content of 15 g/100g; and pulque, a Pre-Hispanic beverage that contains high levels of tryptophan (2.58 g/16 gN) and sulphur amino acids (2.72 g/16 gN). Finally, insects are good sources of sulphur amino acids and lysine.

Comparative evaluation of quality and composition of ostrich, turkey and broiler meat

OpenAIRE

Jukna V.; Klementavičiūtė J.; Meškinytė-Kaušilienė E.; Pečiulaitienė N.; Samborskytė M.; Ambrasūnas L.

2012-01-01

In this article are presented research data on comparative evaluation of meat quality of various poultry species. The study was made on 5 samples of ostrich, turkey and broiler meat. Samples were weighed 500 to 550 grams. Qualitative and nutritional properties of meat from different species of poultry were estimated. The chemical composition, pH, color, firmness, water holding capacity, cooking loss, drip loss of ostrich, turkey and broiler meat were analyz...

SU-E-T-270: Quality Control of Source Strength and Indexer Length in HDR Brachytherapy Using Sun Nuclear Mapcheck2

International Nuclear Information System (INIS)

Morales, J

2014-01-01

Purpose: The goal of this work was to evaluate Sun Nuclear MapCheck2 capability for quantitative determination of both HDR source strength and position. Predictive power of Mapcheck2 dose matrix, originated by a microSelectron-v2 source from 22mm distance, was investigated. Methods: A Mick MultiDoc phantom with the 1400mm indexer length mark aligned over MapCheck2 central detector plus two additional 5cm plastic slabs were used as a composite phantom. Dose readings were transformed by applying published source anisotropy corrections and experimentally established radial dose and relative sensitivity factors. Angular dependence was not considered. Only readings from diodes located 2cm around the central detector were evaluated. The reproducibility of a fit between transformed dose readings and the ratio of virtual source strength and the square of source-detector distance was investigated. Four parameters were considered in the model: virtual source strength, lateral, longitudinal and vertical source positions. Final source strength calibration factor was calculated from the ratio of reference measurements and results from the fit. Results: Original lateral and longitudinal source position estimations had systematic errors of 0.39mm and 0.75mm. After subtracting these errors, both source positions were predicted with a standard deviation of 0.15mm. Results for vertical positions were reproducible with a standard deviation of 0.05mm. The difference between calculated and reference source strengths from 34 independent measurement setups had a standard deviation of 0.3%. The coefficient of determination for the linear regression between known indexer lengths and results from the fit in the range 1400mm ± 5mm was 0.985. Conclusions: ource strength can be estimated with MapCheck2 at appropriate accuracy levels for quality control. Verification of indexer length with present implementation is more accurate than visual alternatives. Results can be improved by designing a

Report on air quality and contribution of individual sources on its pollution in the Slovak Republic, 2002

International Nuclear Information System (INIS)

Mitosinkova, M.; Kozakovic, L.; Zavodsky, D.; Sajtakova, E.; Szemesova, J.; Pukancikova, K.

2003-01-01

A report on air quality and contribution of individual sources on its pollution in the Slovak Republic in 2002 is presented. This report consists of two parts: (1) Pollutants part and (2) Emission part. Pollutants part is divided into the following chapters: Regional air pollution and quality of rainfall waters; Local air pollution; Atmospheric ozone. Emission part is divided into the following chapters: Inventory control of emissions and sources of pollution, Emission of greenhouse gases.

Report on air quality and contribution of individual sources on its pollution in the Slovak Republic, 2004

International Nuclear Information System (INIS)

Mitosinkova, M.; Kozakovic, L.; Zavodsky, D.; Sajtakova, E.; Szemesova, J.; Pukancikova, K.

2005-01-01

A report on air quality and contribution of individual sources on its pollution in the Slovak Republic in 2004 is presented. This report consists of two parts: (1) Pollutants part and (2) Emission part. Pollutants part is divided into the following chapters: Regional air pollution and quality of rainfall waters; Local air pollution; Atmospheric ozone. Emission part is divided into the following chapters: Inventory control of emissions and sources of pollution, Emission of greenhouse gases

Report on air quality and contribution of individual sources on its pollution in the Slovak Republic, 2003

International Nuclear Information System (INIS)

Mitosinkova, M.; Kozakovic, L.; Zavodsky, D.; Sajtakova, E.; Szemesova, J.; Pukancikova, K.

2004-01-01

A report on air quality and contribution of individual sources on its pollution in the Slovak Republic in 2003 is presented. This report consists of two parts: (1) Pollutants part and (2) Emission part. Pollutants part is divided into the following chapters: Regional air pollution and quality of rainfall waters; Local air pollution; Atmospheric ozone. Emission part is divided into the following chapters: Inventory control of emissions and sources of pollution, Emission of greenhouse gases

Sources of variation in quality of South African beef: Case studies in ...

African Journals Online (AJOL)

The South African classification system describes beef carcasses in regard to visual fat cover, conformation and age by dentition. Animal age provides a fairly accurate description of expected eating quality in regard to tenderness in an industry where other sources of variation in tenderness are limited. Since deregulation in ...

A systematic literature review of open source software quality assessment models.

Science.gov (United States)

Adewumi, Adewole; Misra, Sanjay; Omoregbe, Nicholas; Crawford, Broderick; Soto, Ricardo

2016-01-01

Many open source software (OSS) quality assessment models are proposed and available in the literature. However, there is little or no adoption of these models in practice. In order to guide the formulation of newer models so they can be acceptable by practitioners, there is need for clear discrimination of the existing models based on their specific properties. Based on this, the aim of this study is to perform a systematic literature review to investigate the properties of the existing OSS quality assessment models by classifying them with respect to their quality characteristics, the methodology they use for assessment, and their domain of application so as to guide the formulation and development of newer models. Searches in IEEE Xplore, ACM, Science Direct, Springer and Google Search is performed so as to retrieve all relevant primary studies in this regard. Journal and conference papers between the year 2003 and 2015 were considered since the first known OSS quality model emerged in 2003. A total of 19 OSS quality assessment model papers were selected. To select these models we have developed assessment criteria to evaluate the quality of the existing studies. Quality assessment models are classified into five categories based on the quality characteristics they possess namely: single-attribute, rounded category, community-only attribute, non-community attribute as well as the non-quality in use models. Our study reflects that software selection based on hierarchical structures is found to be the most popular selection method in the existing OSS quality assessment models. Furthermore, we found that majority (47%) of the existing models do not specify any domain of application. In conclusion, our study will be a valuable contribution to the community and helps the quality assessment model developers in formulating newer models and also to the practitioners (software evaluators) in selecting suitable OSS in the midst of alternatives.

Nitrogen Isotope Composition of Thermally Produced NOx from Various Fossil-Fuel Combustion Sources.

Science.gov (United States)

Walters, Wendell W; Tharp, Bruce D; Fang, Huan; Kozak, Brian J; Michalski, Greg

2015-10-06

The nitrogen stable isotope composition of NOx (δ(15)N-NOx) may be a useful indicator for NOx source partitioning, which would help constrain NOx source contributions in nitrogen deposition studies. However, there is large uncertainty in the δ(15)N-NOx values for anthropogenic sources other than on-road vehicles and coal-fired energy generating units. To this end, this study presents a broad analysis of δ(15)N-NOx from several fossil-fuel combustion sources that includes: airplanes, gasoline-powered vehicles not equipped with a three-way catalytic converter, lawn equipment, utility vehicles, urban buses, semitrucks, residential gas furnaces, and natural-gas-fired power plants. A relatively large range of δ(15)N-NOx values was measured from -28.1‰ to 8.5‰ for individual exhaust/flue samples that generally tended to be negative due to the kinetic isotope effect associated with thermal NOx production. A negative correlation between NOx concentrations and δ(15)N-NOx for fossil-fuel combustion sources equipped with selective catalytic reducers was observed, suggesting that the catalytic reduction of NOx increases δ(15)N-NOx values relative to the NOx produced through fossil-fuel combustion processes. Combining the δ(15)N-NOx measured in this study with previous published values, a δ(15)N-NOx regional and seasonal isoscape was constructed for the contiguous U.S., which demonstrates seasonal and regional importance of various NOx sources.

Effects of argument quality, source credibility and self-reported diabetes knowledge on message attitudes: an experiment using diabetes related messages.

Science.gov (United States)

Lin, Tung-Cheng; Hwang, Lih-Lian; Lai, Yung-Jye

2017-05-17

Previous studies have reported that credibility and content (argument quality) are the most critical factors affecting the quality of health information and its acceptance and use; however, this causal relationship merits further investigation in the context of health education. Moreover, message recipients' prior knowledge may moderate these relationships. This study used the elaboration likelihood model to determine the main effects of argument quality, source credibility and the moderating effect of self-reported diabetes knowledge on message attitudes. A between-subjects experimental design using an educational message concerning diabetes for manipulation was applied to validate the effects empirically. A total of 181 participants without diabetes were recruited from the Department of Health, Taipei City Government. Four group messages were manipulated in terms of argument quality (high and low) × source credibility (high and low). Argument quality and source credibility of health information significantly influenced the attitude of message recipients. The participants with high self-reported knowledge participants exhibited significant disapproval for messages with low argument quality. Effective health information should provide objective descriptions and cite reliable sources; in addition, it should provide accurate, customised messages for recipients who have high background knowledge level and ability to discern message quality. © 2017 Health Libraries Group Health Information & Libraries Journal.

Effect of Sulphur Fertilization on Grain Quality and Protein Composition of Durum Wheat (Triticum durum Desf.

Directory of Open Access Journals (Sweden)

Marianna Pompa

2009-12-01

Full Text Available The reduction of atmosphere emission of SO2 and the massive use of fertilizers high in nitrogen and phosphorus resulted in a decrease of the sulphur content in the soil. In durum wheat cultivation, sulphur supply plays a key role not only for plant growth, but also for grain quality. Sulphur is an essential macronutrient primarily used to synthesize methionine and cysteine and it is also involved in establishing protein structures by disulphide bonds. The aim of this study was to evaluate the effect of sulphur nutrition on grain quality and protein composition of durum wheat cultivars grown under water deficit conditions, typical of Mediterranean areas. To this purpose, in the 2003-2004 and 2004-2005 crop seasons a field trial was carried out by comparing two water regimes (irrigated and rainfed, two sulphur fertilizer levels and two durum wheat cultivars. Under our experimental conditions, an increase in protein and gluten content in the rainfed treatment and a positive effect of sulphur fertilization on quality parameters were observed. Few changes were observed in protein composition in response to sulphur fertilization.

Strategies to predict and improve eating quality of cooked beef using carcass and meat composition traits in Angus cattle.

Science.gov (United States)

Mateescu, R G; Oltenacu, P A; Garmyn, A J; Mafi, G G; VanOverbeke, D L

2016-05-01

Product quality is a high priority for the beef industry because of its importance as a major driver of consumer demand for beef and the ability of the industry to improve it. A 2-prong approach based on implementation of a genetic program to improve eating quality and a system to communicate eating quality and increase the probability that consumers' eating quality expectations are met is outlined. The objectives of this study were 1) to identify the best carcass and meat composition traits to be used in a selection program to improve eating quality and 2) to develop a relatively small number of classes that reflect real and perceptible differences in eating quality that can be communicated to consumers and identify a subset of carcass and meat composition traits with the highest predictive accuracy across all eating quality classes. Carcass traits, meat composition, including Warner-Bratzler shear force (WBSF), intramuscular fat content (IMFC), trained sensory panel scores, and mineral composition traits of 1,666 Angus cattle were used in this study. Three eating quality indexes, EATQ1, EATQ2, and EATQ3, were generated by using different weights for the sensory traits (emphasis on tenderness, flavor, and juiciness, respectively). The best model for predicting eating quality explained 37%, 9%, and 19% of the variability of EATQ1, EATQ2, and EATQ3, and 2 traits, WBSF and IMFC, accounted for most of the variability explained by the best models. EATQ1 combines tenderness, juiciness, and flavor assessed by trained panels with 0.60, 0.15, and 0.25 weights, best describes North American consumers, and has a moderate heritability (0.18 ± 0.06). A selection index (I= -0.5[WBSF] + 0.3[IMFC]) based on phenotypic and genetic variances and covariances can be used to improve eating quality as a correlated trait. The 3 indexes (EATQ1, EATQ2, and EATQ3) were used to generate 3 equal (33.3%) low, medium, and high eating quality classes, and linear combinations of traits that

Quality label 'Geothermal energy source' (quality-assurance system)

International Nuclear Information System (INIS)

Eugster, W. J.

2005-01-01

The design of borehole heat exchanger (BHE) plants is covered only marginally through the existing quality labels. And only for small and simple systems. Especially the middle and large sized BHE plants are excluded from the labels. And exactly those plants may be very difficult to treat and to handle. Two concepts of quality control are proposed. On one hand a quality label, which is based on an object sheet, that is both, a planning help and a quality proof. There is no duty for the heating/ventilation/air-conditioning (HVAC) engineers to acquire such a quality label. The label is based on a self quality declaration of the engineers. Therefore a controlling system is needed which induces costs to the labelled engineers. A market penetration of around 20% is predicted for the first three years. The second concept is based on a clear definition of the actual state of the art in designing a BHE plant in a formal standard by the Swiss Engineers and Architects Society (SIA). This concept is proposed for realisation. Nearly 90% of the Swiss BHE drilling market is penetrated by the labelled drilling companies which have agreed to demand from their HVAC engineers (planners) to apply the future SIA standard, either by their general drilling and delivery conditions or by a special agreement. This fact guarantees a fast spreading and application of such a new SIA standard. A collateral information offensive for the HVAC engineers working in the design of BHE plants needs to be stated in any way. This method is not only very cheap but also guarantees a fast and a broad market penetration which must have nearly the same grade as the quality label for drilling companies. But of course, the new standard has to be elaborated first, what should be possible within approximately one year. (author)

Removal of light petroleum hydrocarbons from water sources using polypropylene and titanium dioxide nano-composite

Directory of Open Access Journals (Sweden)

H. Karyab

2016-08-01

Full Text Available Background: Petroleum hydrocarbons are the most important pollutants which threat human health and aquatics. Adsorbents are one of the common equipment in water pollution management; however, their applications have been associated with limitations. Objective: To evaluate the potential of polypropylene/titanium dioxide Nano-composite in adsorption of light petroleum hydrocarbons from water sources. Methods: This experimental study was conducted at school of health, Qazvin University of Medical Sciences in 2014-15. Activation of polypropylene fibers, with 1 cm length and 300 microns diameters, was achieved with wet heating. To synthesize of nano-composite the fibers were coated with nano-titanium dioxide with 20 nm diameter. The sonication was performed at 26 kHz and 100 W of power in 40ºc. The morphology of the fractured surfaces of impact specimens was examined by FESEM. The adsorption rate of petrol and gasoline, as surrogate of TPH, was evaluated in different retention time within polyamide mesh aperture diameter of 250 nm. Average of TPH adsorbing, per unit weight of adsorbent, were analyzed with analysis of variance and Scheffe post hoc tests. Findings: The FESEM micrographs showed that the dispersion of the nano-Tio2 particles was relatively good and only few aggregations exist. The maximum adsorption capacity of petrol and gasoline was obtained in 30 minute. The adsorption rate of gasoline was 6.49±0.10 g/g and oil was 7.01±0.13 g/g. Conclusion: According to the results and in comparison with commercial imported adsorbents, the synthesized Nano-composite had favorable performance. The results show that the polypropylene/Tio2 Nano-composite can be used effectively in light petroleum hydrocarbons removal from polluted water sources.

Resin composites

DEFF Research Database (Denmark)

Benetti, Ana Raquel; Peutzfeldt, Anne; Lussi, Adrian

2014-01-01

OBJECTIVE: To investigate how the modulus of elasticity of resin composites influences marginal quality in restorations submitted to thermocyclic and mechanical loading. METHODS: Charisma, Filtek Supreme XTE and Grandio were selected as they were found to possess different moduli of elasticity...... of resin composite (p=0.81) on the quality of dentine margins was observed, before or after loading. Deterioration of all margins was evident after loading (p....008). CONCLUSIONS: The resin composite with the highest modulus of elasticity resulted in the highest number of gap-free enamel margins but with an increased incidence of paramarginal enamel fractures. CLINICAL SIGNIFICANCE: The results from this study suggest that the marginal quality of restorations can...

Report on air quality and contribution of individual sources on its pollution in the Slovak Republic, 2001

International Nuclear Information System (INIS)

Mitosinkova, M.; Kozakovic, L.; Zavodsky, D.; Sajtakova, E.; Mareckova, K.; Pukancikova, K.

2002-01-01

A report on air quality and contribution of individual sources on its pollution in the Slovak Republic in 2001 is presented. This report consists of two parts: (1) Pollutants part and (2) Emission part. Pollutants part is divided into the following chapters: Regional air pollution and quality of precipitation; Local air pollution; Atmospheric ozone. Emission part is divided into the following chapters: Inventory control of emissions and sources of pollution, Emission of greenhouse gases. Emission limits are included

The effect of source credibility on consumers' perceptions of the quality of health information on the Internet.

Science.gov (United States)

Bates, Benjamin R; Romina, Sharon; Ahmed, Rukhsana; Hopson, Danielle

2006-03-01

Recent use of the Internet as a source of health information has raised concerns about consumers' ability to tell 'good' information from 'bad' information. Although consumers report that they use source credibility to judge information quality, several observational studies suggest that consumers make little use of source credibility. This study examines consumer evaluations of web pages attributed to a credible source as compared to generic web pages on measures of message quality. In spring 2005, a community-wide convenience survey was distributed in a regional hub city in Ohio, USA. 519 participants were randomly assigned one of six messages discussing lung cancer prevention: three messages each attributed to a highly credible national organization and three identical messages each attributed to a generic web page. Independent sample t-tests were conducted to compare each attributed message to its counterpart attributed to a generic web page on measures of trustworthiness, truthfulness, readability, and completeness. The results demonstrated that differences in attribution to a source did not have a significant effect on consumers' evaluations of the quality of the information.Conclusions. The authors offer suggestions for national organizations to promote credibility to consumers as a heuristic for choosing better online health information through the use of media co-channels to emphasize credibility.

The concept of a composite perioperative quality index in kidney transplantation.

Science.gov (United States)

Taber, David J; McGillicuddy, John W; Bratton, Charles F; Lin, Angello; Chavin, Kenneth D; Baliga, Prabhakar K

2014-04-01

Public reporting of patient and graft outcomes in a national registry and close Centers for Medicare and Medicaid Services oversight has resulted in transplantation being a highly regulated surgical discipline. Despite this, transplantation surgery lacks comprehensive tracking and reporting of perioperative quality measures. Therefore, the aim of this study was to determine the association between a kidney transplantation centers' perioperative quality benchmarking and graft and patient outcomes. This was an analysis of 2011 aggregate data compiled from 2 national datasets that track outcomes from member hospitals and transplantation centers. The transplantation centers included in this study were composed of accredited US kidney transplantation centers that report data through the national registry and are associate members of the University HealthSystem Consortium. A total of 16,811 kidney transplantations were performed at 236 centers in the United States in 2011, of which 10,241 (61%) from 93 centers were included in the analysis. Of the 6 perioperative quality indicators, 3 benchmarked metrics were significantly associated with a kidney transplantation center's underperformance: mean ICU length of stay (C-statistic 0.731; p = 0.002), 30-day readmissions (C-statistic 0.697; p = 0.012) and in-hospital complications (C-statistic 0.785; p = 0.001). The composite quality index strongly correlated with inadequate center performance (C-statistic 0.854; p < 0.001, R(2) = 0.349). The centers in the lowest quartile of the quality index performed 2,400 kidney transplantations in 2011, which led to 2,640 more hospital days, 4,560 more ICU days, 120 more postoperative complications, and 144 more patients with 30-day readmissions, when compared with centers in the 3 higher-quality quartiles. An objective index of a transplantation center's quality of perioperative care is significantly associated with patient and graft survival. Copyright © 2014 American College of

Multifunctional voltage source inverter for renewable energy integration and power quality conditioning.

Science.gov (United States)

Dai, NingYi; Lam, Chi-Seng; Zhang, WenChen

2014-01-01

In order to utilize the energy from the renewable energy sources, power conversion system is necessary, in which the voltage source inverter (VSI) is usually the last stage for injecting power to the grid. It is an economical solution to add the function of power quality conditioning to the grid-connected VSI in the low-voltage distribution system. Two multifunctional VSIs are studied in this paper, that is, inductive-coupling VSI and capacitive-coupling VSI, which are named after the fundamental frequency impedance of their coupling branch. The operation voltages of the two VSIs are compared when they are used for renewable energy integration and power quality conditioning simultaneously. The operation voltage of the capacitive-coupling VSI can be set much lower than that of the inductive-coupling VSI when reactive power is for compensating inductive loads. Since a large portion of the loads in the distribution system are inductive, the capacitive-coupling VSI is further studied. The design and control method of the multifunctional capacitive-coupling VSI are proposed in this paper. Simulation and experimental results are provided to show its validity.

A numerical analysis of a composition-adjustable Kalina cycle power plant for power generation from low-temperature geothermal sources

International Nuclear Information System (INIS)

Wang, Enhua; Yu, Zhibin

2016-01-01

Highlights: • A composition-adjustable Kalina cycle is analysed and presented. • An air-cooled condenser is used and thermodynamic performance is analysed. • Composition adjustment can improve system performance significantly. - Abstract: The Kalina cycle is believed to be one of the most promising technologies for power generation from low temperature heat sources such as geothermal energy. So far, most Kalina cycle power plants are designed with a working fluid mixture having a fixed composition, and thus normally operate at a fixed condensing temperature. However, the ambient temperature (i.e., heat sink) varies over a large range as the season changes over a year, particularly in continental climates. Recently, a new concept, i.e., composition-adjustable Kalina cycle, was proposed to develop power plants that can match their condensing temperature with the changing ambient conditions, aiming at improving the cycle’s overall thermal efficiency. However, no detailed analysis of its implementation and the potential benefits under various climate conditions has been reported. For this reason, this paper carried out a comprehensive numerical research on its implementation and performance analysis under several different climate conditions. A mathematical model is firstly established to simulate the working principle of a composition-adjustable Kalina cycle, based on which a numerical program is then developed to analyse the cycle’s performance under various climate conditions. The developed numerical model is verified with some published data. The dynamic composition adjustment in response to the changing ambient temperature is simulated to evaluate its effect on the plant’s performance over a year. The results show that a composition-adjustable Kalina cycle could achieve higher annual-average thermal efficiency than a conventional one with a fixed mixture composition. However, such an improvement of thermal efficiency strongly depends on the heat source

Analysis of pollen load based on color, physicochemical composition and botanical source

Directory of Open Access Journals (Sweden)

Anna F.H. Modro

2009-06-01

Full Text Available Pollen load samples from 10 hives of Apis mellifera (L. were analyzed based on their physicochemical composition and botanical source, considering color as a parameter for quality control. In seven samples it was possible to establish the occurrence of more than 80% of a single pollen type, characterizing them as unifloral but with protein content variation. One of the samples was exclusively composed of saprophytic fungi (Cladosporium sp.. Comparing the mean results of the fungi loads with those of the nutritional components of pollen load, the former presented higher protein, mineral matter and dry matter and lower organic matter, ethereal extract and total carbohydrate values. The monochromatic samples met the physicochemical specifications regulating pollen load quality. The results showed that homogeneous coloration of the pollen load was not found to be a good indication of unifloral pollen, confirming the importance of physicochemical analysis and melissopalynological analysis for characterization of the quality of commercial pollen load.Amostras de cargas de pólen de 10 colméias de Apis mellifera (L. foram analisadas quanto a sua composição físico-química e origem botânica, tomando-se a coloração como parâmetro para o controle de qualidade. Em sete amostras foi possível estabelecer a ocorrência de mais de 80% de um único tipo polínico, caracterizando-as como monoflorais, porém com variações nos valores protéicos. Uma das amostras era composta exclusivamente por fungos saprofíticos (Cladosporium sp.. Comparando-se as bolotas de fungos com os resultados médios dos componentes nutricionais das bolotas de pólen, as primeiras apresentaram maior valor protéico, matéria mineral e matéria seca e menores valores de matéria orgânica, extrato etéreo ecarboidratos totais. As amostras monocromáticas estiveram de acordo com as especificações físico-químicas reguladoras da qualidade de pólen apícola. Os resultados

Sources of trends in water-quality data for selected streams in Texas, 1975-89 water years

Science.gov (United States)

Schertz, T.L.; Wells, F.C.; Ohe, D.J.

1994-01-01

Sources of trends in water-quality data for selected streams in Texas for the 1975-89 water years were investigated in this study. The investigation of sources was confined to distinct geographic patterns in the trend indicators for one constituent or for a group of related constituents.

The effect of Bovine Growth Hormone on Growth, Carcass Composition and Meat Quality of Dairy Heifers

DEFF Research Database (Denmark)

Vestergaard, Mogens; Sejrsen, Kristen; Foldager, John

1993-01-01

, one animal was given daily subcutaneous injections of 20 IU of pituitary-derived bGH (15-20 mg), while the other animal was injected with saline (excipient). Treatments started at 179±2 kg body weight and lasted for 15.6 weeks. At slaughter, carcass composition and meat quality were analyzed. b......Our objective was to examine the effects of bovine growth hormone (bGH) on growth, carcass composition and meat quality of dairy heifers. Nine monozygotic twin pairs of Friesian or Red Danish cattle were used, and pair-fed diet consisting of grass silage, barley and soybean meal. Within each pair......GH treatment increased gain by 8% (948 vs. 877 g/d; P carcass and lean content of four main carcass cuts were on average increased by 2% (P carcass fat trim was reduced by 12% (P

Primary calibrations of radionuclide solutions and sources for the EML quality assessment program

Energy Technology Data Exchange (ETDEWEB)

Fisenne, I.M. [Dept. of Energy, New York, NY (United States)

1993-12-31

The quality assurance procedures established for the operation of the U.S. Department of Energy`s Environmental Measurements Laboratory (DOE-EML`s) Quality Assessment Program (QAP) are essentially the same as those that are in effect for any EML program involving radiometric measurements. All these programs have at their core the use of radionuclide standards for their instrument calibration. This paper focuses on EML`s approach to the acquisition, calibration and application of a wide range of radionuclide sources that are required to meet its programmatic needs.

Evaluation of nutritive quality of common carp, Cyprinus carpio L.

Science.gov (United States)

Ljubojević, D.; Đorđević, V.; Ćirković, M.

2017-09-01

Common carp is the most important commercial fish species in Serbia. This fish is a valuable source of nutritive components and plays a role in healthy human nutrition. This review evaluates the nutritive quality of common carp including proximate and fatty acid compositions as well as their effects on human health. The fat content and fatty acid composition of carp have been shown to vary due to different environmental factors and particularly due to nutrition. Technology of production and composition of planktonic and benthic organisms in fish ponds have been recognised as significant factors affecting carp meat quality and desirable chemical and fatty acid composition. Carp meat quality but also production parameters and fish health are positively influenced by a balanced feed mixture. Due to the low content of saturated fatty acids and cholesterol plus high levels of unsaturated fatty acids, common carp meat consumption could be linked with reduced risk of different heart diseases in humans. Also, fish proteins can have many beneficial roles in the preservation of human health. This paper emphasises the importance of consumption of common carp in order to prevent many diseases and preserve human health.

Assessing data quality and the variability of source data verification auditing methods in clinical research settings.

Science.gov (United States)

Houston, Lauren; Probst, Yasmine; Martin, Allison

2018-05-18

Data audits within clinical settings are extensively used as a major strategy to identify errors, monitor study operations and ensure high-quality data. However, clinical trial guidelines are non-specific in regards to recommended frequency, timing and nature of data audits. The absence of a well-defined data quality definition and method to measure error undermines the reliability of data quality assessment. This review aimed to assess the variability of source data verification (SDV) auditing methods to monitor data quality in a clinical research setting. The scientific databases MEDLINE, Scopus and Science Direct were searched for English language publications, with no date limits applied. Studies were considered if they included data from a clinical trial or clinical research setting and measured and/or reported data quality using a SDV auditing method. In total 15 publications were included. The nature and extent of SDV audit methods in the articles varied widely, depending upon the complexity of the source document, type of study, variables measured (primary or secondary), data audit proportion (3-100%) and collection frequency (6-24 months). Methods for coding, classifying and calculating error were also inconsistent. Transcription errors and inexperienced personnel were the main source of reported error. Repeated SDV audits using the same dataset demonstrated ∼40% improvement in data accuracy and completeness over time. No description was given in regards to what determines poor data quality in clinical trials. A wide range of SDV auditing methods are reported in the published literature though no uniform SDV auditing method could be determined for "best practice" in clinical trials. Published audit methodology articles are warranted for the development of a standardised SDV auditing method to monitor data quality in clinical research settings. Copyright © 2018. Published by Elsevier Inc.

Chemical composition, true nutrient digestibility, and true metabolizable energy of novel pet food protein sources using the precision-fed cecectomized rooster assay.

Science.gov (United States)

Deng, P; Utterback, P L; Parsons, C M; Hancock, L; Swanson, K S

2016-08-01

A wide variety of animal protein-based ingredients is commonly used in the pet food products. The raw ingredients and processing procedures used may greatly affect protein quality. Testing the quality of alternative protein sources is necessary and contributes to the sustainability of pet foods. The objective of this study was to test the chemical composition of 8 protein sources intended for use in dog and cat foods (calamari meal, pork peptone, alligator meal, lamb meal, venison meal, chicken meal, and 2 duck meals), and evaluate their true nutrient digestibility and nitrogen-corrected true ME (TMEn) using the precision-fed cecectomized rooster assay. Calamari meal and pork peptone had lower ash (4.4 and 3.6% of DM, respectively) but greater CP (88.1 and 80.5% of DM, respectively) and either greater or similar GE (5.6 and 5.3 kcal/g of DM, respectively) compared with alligator, lamb, venison, chicken, and duck meals (11.8 to 24.5% ash, 58.7 to 65.9% CP, and 4.6 to 5.3 kcal GE/g). Acid-hydrolyzed fat (AHF) was lower in calamari meal (8.7% of DM) compared with the other proteins tested (15.5-22.1% of DM). True nutrient digestibility was variable among the protein sources (52 to 79% of DM, 60 to 83% of OM, 78 to 92% of AHF, and 70 to 89% of GE) with pork peptone having the highest DM, AHF, and GE digestibility and calamari meal having the highest OM digestibility. True indispensable AA digestibility was highest for calamari meal, with all AA having a digestibility greater than 90%. Except for histidine, all indispensable AA had a digestibility over 85% for pork peptone. In contrast, true indispensable AA digestibility was lowest for lamb meal, with histidine having digestibility less than 70% and the other entire indispensable AA having digestibility between 72 and 88%. The TMEn of calamari meal (4.82 kcal/g DM and 86.9% of GE) was greater ( digestibility among protein sources intended for use in dog and cat foods and justifies further in vivo testing of novel

A national look at water quality

Science.gov (United States)

Gilliom, Robert J.; Mueller, David K.; Zogorski, John S.; Ryker, Sarah J.

2002-01-01

Most water-quality problems we face today result from diffuse "nonpoint" sources of pollution from agricultural land, urban development, forest harvesting and the atmosphere (U.S. Army Corps of Engineers et al., 1999). It is difficult to quantify nonpoint sources because the contaminants they deliver vary in composition and concentrations from hour to hour and season to season. Moreover, the nature of the contamination is complex and varied. When Congress enacted the Clean Water Act 30 years ago, attention was focused on water-quality issues related to the sanitation of rivers and streams - bacteria counts, oxygen in the water for fish, nutrients, temperature, and salinity. Now, attention is turning to the hundreds of synthetic organic compounds like pesticides used in agricultural and residential areas, volatile organics in solvents and gasoline, microbial and viral contamination, and pharmaceuticals and hormones.

ISS Ambient Air Quality: Updated Inventory of Known Aerosol Sources

Science.gov (United States)

Meyer, Marit

2014-01-01

Spacecraft cabin air quality is of fundamental importance to crew health, with concerns encompassing both gaseous contaminants and particulate matter. Little opportunity exists for direct measurement of aerosol concentrations on the International Space Station (ISS), however, an aerosol source model was developed for the purpose of filtration and ventilation systems design. This model has successfully been applied, however, since the initial effort, an increase in the number of crewmembers from 3 to 6 and new processes on board the ISS necessitate an updated aerosol inventory to accurately reflect the current ambient aerosol conditions. Results from recent analyses of dust samples from ISS, combined with a literature review provide new predicted aerosol emission rates in terms of size-segregated mass and number concentration. Some new aerosol sources have been considered and added to the existing array of materials. The goal of this work is to provide updated filtration model inputs which can verify that the current ISS filtration system is adequate and filter lifetime targets are met. This inventory of aerosol sources is applicable to other spacecraft, and becomes more important as NASA considers future long term exploration missions, which will preclude the opportunity for resupply of filtration products.

Estimating the Pollution Risk of Cadmium in Soil Using a Composite Soil Environmental Quality Standard

Science.gov (United States)

Huang, Biao; Zhao, Yongcun

2014-01-01

Estimating standard-exceeding probabilities of toxic metals in soil is crucial for environmental evaluation. Because soil pH and land use types have strong effects on the bioavailability of trace metals in soil, they were taken into account by some environmental protection agencies in making composite soil environmental quality standards (SEQSs) that contain multiple metal thresholds under different pH and land use conditions. This study proposed a method for estimating the standard-exceeding probability map of soil cadmium using a composite SEQS. The spatial variability and uncertainty of soil pH and site-specific land use type were incorporated through simulated realizations by sequential Gaussian simulation. A case study was conducted using a sample data set from a 150 km2 area in Wuhan City and the composite SEQS for cadmium, recently set by the State Environmental Protection Administration of China. The method may be useful for evaluating the pollution risks of trace metals in soil with composite SEQSs. PMID:24672364

The independent association between diet quality and body composition.

Science.gov (United States)

Drenowatz, Clemens; Shook, Robin P; Hand, Gregory A; Hébert, James R; Blair, Steven N

2014-05-12

Excess body weight is associated with an imbalance between energy expenditure and dietary intake but evidence on the association between diet quality and body composition remains equivocal. Rather than relying on differences in diet quality between overweight/obese and normal weight adults, this study examined the association between the Healthy Eating Index 2010 (HEI-2010) and body fatness on a continuous scale, independent of physical activity (PA). Further the association between components of the HEI-2010 and risk for overweight/obesity was explored. 407 adults (27.6 ± 3.7 years) provided at least two 24-hour diet recalls over a period of 14 days, which were used to calculate the HEI-2010. Percent body fat (BF) was assessed via dual X-ray absorptiometry and PA was determined via a multi-sensor device, worn over a period of 10 days. PA was a stronger contributor to the variability in BF than the HEI-2010 and the association between HEI-2010 and BF was significant only in men. Particularly a high consumption of protein, sodium and empty calories increased the risk for overweight/obesity. Adherence to dietary guidelines positively affects body fatness in men, independent of PA. In contrast to current dietary recommendations, the risk for overweight/obesity was increased with a higher protein intake.

Z-Source Inverter Based Power Quality Compensator with Enhanced Ride-Through Capability

DEFF Research Database (Denmark)

Gajanayake, C.J.; Vilathgamuwa, D.M.; Loh, P.C.

2007-01-01

Distributed generation has been gaining acceptance over the years and it has the potential to provide reliable power to sensitive loads. However, distributed networks are prone to unbalanced faults conditions. This makes single inverter DG systems unsuitable as UPS systems. This paper proposes...... a Zsource inverter based power quality compensator and a control structure that supplies high quality voltage to the connected sensitive load in the presence of other non linear loads. The proposed topology consists of combination of shunt and series inverters connected to a common Z-source impedance...... network. The shunt inverter is controlled to maintain a quality voltage waveform at the load bus. Whereas the series inverter enhances the ride-through capability during grid faults, protects the shunt inverter by limiting the current and also controls the power delivered to the grid. The performance...

Composition and source apportionment of dust fall around a natural lake.

Science.gov (United States)

Latif, Mohd Talib; Ngah, Sofia Aida; Dominick, Doreena; Razak, Intan Suraya; Guo, Xinxin; Srithawirat, Thunwadee; Mushrifah, Idris

2015-07-01

The aim of this study was to determine the source apportionment of dust fall around Lake Chini, Malaysia. Samples were collected monthly between December 2012 and March 2013 at seven sampling stations located around Lake Chini. The samples were filtered to separate the dissolved and undissolved solids. The ionic compositions (NO3-, SO4(2-), Cl- and NH4+) were determined using ion chromatography (IC) while major elements (K, Na, Ca and Mg) and trace metals (Zn, Fe, Al, Ni, Mn, Cr, Pb and Cd) were determined using inductively coupled plasma mass spectrometry (ICP-MS). The results showed that the average concentration of total solids around Lake Chini was 93.49±16.16 mg/(m2·day). SO4(2-), Na and Zn dominated the dissolved portion of the dust fall. The enrichment factors (EF) revealed that the source of the trace metals and major elements in the rain water was anthropogenic, except for Fe. Hierarchical agglomerative cluster analysis (HACA) classified the seven monitoring stations and 16 variables into five groups and three groups respectively. A coupled receptor model, principal component analysis multiple linear regression (PCA-MLR), revealed that the sources of dust fall in Lake Chini were dominated by agricultural and biomass burning (42%), followed by the earth's crust (28%), sea spray (16%) and a mixture of soil dust and vehicle emissions (14%). Copyright © 2015. Published by Elsevier B.V.

The Effect of Nylon and Polyester Peel Ply Surface Preparation on the Bond Quality of Composite Laminates

Science.gov (United States)

Moench, Molly K.

The preparation of the surfaces to be bonded is critical to the success of composite bonds. Peel ply surface preparation is attractive from a manufacturing and quality assurance standpoint, but is a well known example of the extremely system-specific nature of composite bonds. This study examined the role of the surface energy, morphology, and chemistry left by peel ply removal in resulting bond quality. It also evaluated the use of contact angle surface energy measurement techniques for predicting the resulting bond quality of a prepared surface. The surfaces created by preparing three aerospace fiber-reinforced composite prepregs were compared when prepared with a nylon vs a polyester peel ply. The prepared surfaces were characterized with contact angle measurements with multiple fluids, scanning electron microscopy (SEM), and x-ray electron spectroscopy. The laminates were bonded with aerospace grade film adhesives. Bond quality was assessed via double cantilever beam testing followed by optical and scanning electron microscopy of the fracture surfaces.The division was clear between strong bonds (GIC of 600- 1000J/m2 and failure in cohesion) and weak bonds (GIC of 80-400J/m2 and failure in adhesion). All prepared laminates showed the imprint of the peel ply texture and evidence of peel ply remnants after fabric removal, either through SEM or XPS. Within an adhesive system, large amounts of SEM-visible peel ply material transfer correlated with poor bond quality and cleaner surfaces with higher bond quality. The both sides of failed weak bonds showed evidence of peel ply remnants under XPS, showing that at least some failure is occurring through the remnants. The choice of adhesive was found to be significant. AF 555 adhesive was more tolerant of peel ply contamination than MB 1515-3. Although the bond quality results varied substantially between tested combinations, the total surface energies of all prepared surfaces were very similar. Single fluid contact angle

Effect of Polymer Form and its Consolidation on Mechanical Properties and Quality of Glass/PBT Composites

Science.gov (United States)

Durai Prabhakaran, R. T.; Pillai, Saju; Charca, Samuel; Oshkovr, Simin Ataollahi; Knudsen, Hans; Andersen, Tom Løgstrup; Bech, Jakob Ilsted; Thomsen, Ole Thybo; Lilholt, Hans

2014-04-01

The aim of this study was to understand the role of the processing in determining the mechanical properties of glass fibre reinforced polybutylene terephthalate composites (Glass/PBT). Unidirectional (UD) composite laminates were manufactured by the vacuum consolidation technique using three different material systems included in this study; Glass/CBT (CBT160 powder based resin), Glass/PBT (prepreg tapes), and Glass/PBT (commingled yarns). The different types of thermoplastic polymer resin systems used for the manufacturing of the composite UD laminate dictate the differences in final mechanical properties which were evaluated by through compression, flexural and short beam transverse bending tests. Microscopy was used to evaluate the quality of the processed laminates, and fractography was used to characterize the observed failure modes. The study provides an improved understanding of the relationships between processing methods, resin characteristics, and mechanical performance of thermoplastic resin composite materials.

Size, Composition, and Source Profiles of Inhalable Bioaerosols from Colorado Dairies

Energy Technology Data Exchange (ETDEWEB)

Schaeffer, Joshua W; Reynolds, Stephen; Magzamen, Sheryl; VanDyke, Amanda; Gottel, Neil R.; Gilbert, Jack A.; Owens, Sarah M.; Hampton-Marcell, Jarrad; Volckens, John

2017-06-06

Particulate matter emissions from agricultural livestock operations contain both chemical and biological constituents that represent a potential human health hazard. The size and composition of these dusts, however, have not been well described. We evaluated the full size distribution (from 0 to 100 μm in aerodynamic diameter) and chemical/biological composition of inhalable dusts inside several Colorado dairy parlors. Four aerodynamic size fractions (<3, 3-10, 10-30, and >30 μm) were collected and analyzed using a combination of physiochemical techniques to understand the structure of bacterial communities and chemical constituents. Airborne particulate mass followed a bimodal size distribution (one mode at 3 μm and a second above 30 μm), which also correlated with the relative concentrations of the following microbiological markers: bacterial endotoxin, 3-hydroxy fatty acids, and muramic acid. Sequencing of the 16S- rRNA components of this aerosol revealed a microbiome derived predominantly from animal sources. Bacterial genera included Staphlyococcus, Pseudomonas, and Streptococcus, all of which have proinflammatory and pathogenic capacity. Our results suggest that the size distribution of bioaerosols emitted by dairy operations extends well above 10 μm in diameter and contains a diverse mixture of potentially hazardous constituents and opportunistic pathogens. These findings should inform the development of more effective emissions control strategies.

Swept source optical coherence tomography for quantitative and qualitative assessment of dental composite restorations

Science.gov (United States)

Sadr, Alireza; Shimada, Yasushi; Mayoral, Juan Ricardo; Hariri, Ilnaz; Bakhsh, Turki A.; Sumi, Yasunori; Tagami, Junji

2011-03-01

The aim of this work was to explore the utility of swept-source optical coherence tomography (SS-OCT) for quantitative evaluation of dental composite restorations. The system (Santec, Japan) with a center wavelength of around 1300 nm and axial resolution of 12 μm was used to record data during and after placement of light-cured composites. The Fresnel phenomenon at the interfacial defects resulted in brighter areas indicating gaps as small as a few micrometers. The gap extension at the interface was quantified and compared to the observation by confocal laser scanning microscope after trimming the specimen to the same cross-section. Also, video imaging of the composite during polymerization could provide information about real-time kinetics of contraction stress and resulting gaps, distinguishing them from those gaps resulting from poor adaptation of composite to the cavity prior to polymerization. Some samples were also subjected to a high resolution microfocus X-ray computed tomography (μCT) assessment; it was found that differentiation of smaller gaps from the radiolucent bonding layer was difficult with 3D μCT. Finally, a clinical imaging example using a newly developed dental SS-OCT system with an intra-oral scanning probe (Panasonic Healthcare, Japan) is presented. SS-OCT is a unique tool for clinical assessment and laboratory research on resin-based dental restorations. Supported by GCOE at TMDU and NCGG.

Composition and sources of particles in Mannerheimintie during exceedance days of PM{sub 10} limit value in 2009; Hiukkasten koostumus ja laehteet Mannerheimintiellae PM{sub 10}-raja-arvon ylityspaeivinae 2009

Energy Technology Data Exchange (ETDEWEB)

Kupiainen, K.; Stojiljkovic, A.; Ritola, R. (Nordic Envicon Oy, Helsinki (Finland))

2011-06-15

The purpose of the work was to determine sources of thoracic particles (PM{sub 10}) in the center of Helsinki, in Mannerheimintie, in 2009 during the days when the daily average concentration of PM{sub 10} exceeded 50 mug/m3. Work was commissioned by the Helsinki City Public Works department, the Helsinki Environment Centre and the Helsinki Region Environmental Services Authority HSY (formerly YTV). By the end of the year there were altogether 30 exceedance days. The allowed number of exceedance days per year is 35, so the limit value was not exceeded in 2009. HSY is responsible for monitoring the air quality in the Helsinki metropolitan area. The PM{sub 10} monitoring data in combination with electron microscopy based single particle compositional analysis and receptor modeling was used to evaluate dust source contributions on the exceedance days at HSY's air quality monitoring station in Mannerheimintie. Dust sources related to traction control (winter maintenance and pavement wear by studded tyres) contributed most to the PM{sub 10} concentrations in Mannerheimintie. On 12 exceeding days this group accounted for more than 50 % of PM{sub 10} particles, on 3 days the group alone was sufficient to cause the exceedance. On 3 of the exceedance days long-range transboundary air pollution or traffic exhaust emissions were on the same level with the traction control sources. On 11 days the most significant impact came from construction sites. (orig.)

Quality and security on the uses of cobalt 60 sources for industrial irradiators

International Nuclear Information System (INIS)

Desroches, J.

1976-01-01

The construction and operation of industrial irradiators using large quantities of cobalt 60 give rise to an important problem of security. The CEA Radioisotope Department which manufactures and sells sources of Co60 has created an insurance Quality System which insures the maximum of security for the user. (author)

Quality and security on the uses of cobalt 60 sources for industrial irradiators

International Nuclear Information System (INIS)

Desroches, J.

1976-01-01

The construction and operation of industrial irradiators using large quantities of 60 Co give rise to an important problem of security. The CEA Radioisotope Department which manufactures and sells sources of 60 Co has created an insurance Quality System which insures the maximum of security for the user

Effect of nutrient enrichment on the source and composition of sediment organic carbon in tropical seagrass beds in the South China Sea

International Nuclear Information System (INIS)

Liu, Songlin; Jiang, Zhijian; Zhang, Jingping; Wu, Yunchao; Lian, Zhonglian; Huang, Xiaoping

2016-01-01

To assess the effect of nutrient enrichment on the source and composition of sediment organic carbon (SOC) beneath Thalassia hemprichii and Enhalus acoroides in tropical seagrass beds, Xincun Bay, South China Sea, intertidal sediment, primary producers, and seawater samples were collected. No significant differences on sediment δ 13 C, SOC, and microbial biomass carbon (MBC) were observed between T. hemprichii and E. acoroides. SOC was mainly of autochthonous origin, while the contribution of seagrass to SOC was less than that of suspended particulate organic matter, macroalgae and epiphytes. High nutrient concentrations contributed substantially to SOC of seagrass, macroalgae, and epiphytes. The SOC, MBC, and MBC/SOC ratio in the nearest transect to fish farming were the highest. This suggested a more labile composition of SOC and shorter turnover times in higher nutrient regions. Therefore, the research indicates that nutrient enrichment could enhance plant-derived contributions to SOC and microbial use efficiency. - Highlights: • Response of sources and composition of SOC to nutrient enrichment was observed. • Similar SOC sources and composition were observed in the two seagrass communities. • Nutrient enrichment enhanced seagrass and macroalgae and epiphytes contribution to SOC. • High nutrient concentration stimulated the MBC and the MBC/SOC ratio.

Apportionment of sources affecting water quality: Case study of Kandla Creek, Gulf of Katchchh

Digital Repository Service at National Institute of Oceanography (India)

Dalal, S.G.; Shirodkar, P.V.; Verlekar, X.N.; Jagtap, T.G.; Rao, G.S.

status of the environment. Several multivariate models are used for source apportionment studies, as they pinpoint the possible factors or sources that influence the water quality (Morales et al., 1999; Wunderlin et al., 2001; Petersen et al., 2001... and statistical approaches. Ecology 74: 2201– 2214. Morales, M. M., Martih, P., Llopis, A., Campos, L., and Sagrado, J. 1999. An environmental study by factor analysis of surface seawater in the Gulf of Valencia (western Mediterranean). Analytica Chimica Acta 394...

Composition of fatty acids in selected vegetable oils

OpenAIRE

Helena Frančáková; Eva Ivanišová; Štefan Dráb; Tomáš Krajčovič; Marián Tokár; Ján Mareček; Janette Musilová

2015-01-01

Plant oils and fats are important and necessary components of the human nutrition. They are energy source and also contain fatty acids - compounds essential for human health. The aim of this study was to evaluate nutritional quality of selected plant oil - olive, rapeseed, pumpkin, flax and sesame; based on fatty acid composition in these oils. Fatty acids (MUFA, PUFA, SFA) were analyzed chromatography using system Agilent 6890 GC, injector multimode, detector FID. The highest c...

Water quality and possible sources of nitrate in the Cimarron Terrace Aquifer, Oklahoma, 2003

Science.gov (United States)

Masoner, Jason R.; Mashburn, Shana L.

2004-01-01

Water from the Cimarron terrace aquifer in northwest Oklahoma commonly has nitrate concentrations that exceed the maximum contaminant level of 10 milligrams per liter of nitrite plus nitrate as nitrogen (referred to as nitrate) set by the U.S. Environmental Protection Agency for public drinking water supplies. Starting in July 2003, the U.S. Geological Survey, in cooperation with the Oklahoma Department of Environmental Quality, conducted a study in the Cimarron terrace aquifer to assess the water quality and possible sources of nitrate. A qualitative and quantitative approach based on multiple lines of evidence from chemical analysis of nitrate, nitrogen isotopes in nitrate, pesticides (indicative of cropland fertilizer application), and wastewater compounds (indicative of animal or human wastewater) were used to indicate possible sources of nitrate in the Cimarron terrace aquifer. Nitrate was detected in 44 of 45 ground-water samples and had the greatest median concentration (8.03 milligrams per liter) of any nutrient analyzed. Nitrate concentrations ranged from chemicals, 3 compounds were hydrocarbons, 2 compounds were industrial chemicals, 2 compounds were pesticides, 1 compound was of animal source, and 1 compound was a detergent compound. The most frequently detected wastewater compound was phenol, which was detected in 23 wells. N,N-diethyl-meta-toluamide (DEET) was detected in water samples from 5 wells. Benzophenone, ethanol- 2-butoxy-phosphate, and tributylphosphate were detected in water samples from 3 wells. Fertilizer was determined to be the possible source of nitrate in samples from 13 of 45 wells sampled, with a15N values ranging from 0.43 to 3.46 permil. The possible source of nitrate for samples from the greatest number of wells (22 wells) was from mixed sources of nitrate from fertilizer, septic or manure, or natural sources. Mixed nitrate sources had a 15N values ranging from 0.25 to 9.83 permil. Septic or manure was determined as the possible

Chemical Composition and Emission Sources of the Fine Particulate Matters in a Southeast Asian Mega City (Dhaka, Bangladesh)

Science.gov (United States)

Salam, Abdus

2016-04-01

Air pollution has significant impact on human health, climate change, agriculture, visibility reduction, and also on the atmospheric chemistry. There are many studies already reported about the direct relation of the human mortality and morbidity with the increase of the atmospheric particulate matters. Especially, fine particulate matters can easily enter into the human respiratory system and causes many diseases. Particulate matters have the properties to absorb the solar radiation and impact on the climate. Dhaka, Bangladesh is a densely populated mega-city in the world. About 16 million inhabitants are living within an area of 360 square kilometers. Air quality situation has been degrading due to unplanned growth, increasing vehicles, severe traffic jams, brick kilns, industries, construction, and also transboundary air pollution. A rapidly growing number of vehicles has worsen the air quality in spite of major policy interventions, e.g., ban of two-stroke and three-wheeled vehicles, phase out of 20 years old vehicles, conversion to compressed natural gas (CNGs), etc. Introduction of CNGs to reduce air pollution was not the solution for fine particles at all, as evidence shows that CNGs and diesel engines are the major sources of fine particles. High concentration of the air pollutants in Dhaka city such as PM, carbonaceous species (black and organic carbon), CO, etc. has already been reported. PM2.5 mass, chemical composition (e.g., BC, OC, SO42-, NO3-, trace elements, etc.), aerosol Optical Depth (AOD) and emission sources of our recent measurements at the highly polluted south East Asian Mega city (Dhaka) Bangladesh will be presented in the conference. PM2.5 samples were collected on filters with Digital PM2.5 sampler (Switzerland) and Air photon, USA. BC was measured from filters (with thermal and optical method) and also real time with an Aethalometer AE42 (Magee Scitific., USA). Water soluble ions were determined from filters with ion chromatogram. AOD

Hydrologic, Water-Quality, and Meteorological Data for the Cambridge, Massachusetts, Drinking-Water Source Area, Water Year 2006

Science.gov (United States)

Smith, Kirk P.

2008-01-01

mean specific conductance for water year 2005 which was 737 uS/cm. However, the annual mean specific conductance at Stony Brook near Route 20 in Waltham (U.S. Geological Survey (USGS) station 01104460), on the principal tributary to the Stony Brook Reservoir, and at USGS station 01104475 on a smaller tributary to the Stony Brook Reservoir were about 15 and 13 percent lower, respectively, than the previous annual mean specific conductances of 538 and 284 uS/cm, respectively for water year 2005. The annual mean specific conductance for Fresh Pond Reservoir decreased from 553 uS/cm in the 2005 water year to 514 uS/cm in the 2006 water year. Water samples were collected in nearly all of the subbasins in the Cambridge drinking-water source area and from Fresh Pond during water year 2006. Discrete water samples were collected during base-flow conditions with an antecedent dry period of at least 4 days. Composite samples, consisting of as many as 100 subsamples, were collected by automatic samplers during storms. Concentrations of most dissolved constituents were generally lower in samples of stormwater than in samples collected during base flow; however, the average concentration of total phosphorus in samples of stormwater were from 160 to 1,109 percent greater than the average concentration in water samples collected during base-flow conditions. Concentrations of total nitrogen in water samples collected during base-flow conditions and composite samples of stormwater at USGS stations 01104415, 01104460, and 01104475 were similar, but mean concentrations of total nitrogen in samples of stormwater differed by about 0.5 mg/L (milligrams per liter) from those in water samples collected during base-flow conditions at U.S. Geological Survey stations 01104433 and 01104455. In six water samples, measurements of pH were lower than the U.S. Environmental Protection Agency (USEPA) national recommended freshwater quality criteria and the USEPA secondary drinking water-standa

Quality and security on the uses of cobalt 60 sources for industrial irradiators

International Nuclear Information System (INIS)

Desroches, J.

1976-01-01

The construction and operation of industrial irradiators using large quantities of 60 Co give rise to an important problem of security. The CEA Radioisotope Department which manufactures and sells sources of 60 Co has created an insurance quality system which insures the maximum of security for the user. (orig.) [de

Aerosol composition, oxidation properties, and sources in Beijing: results from the 2014 Asia-Pacific Economic Cooperation summit study

Science.gov (United States)

Xu, W. Q.; Sun, Y. L.; Chen, C.; Du, W.; Han, T. T.; Wang, Q. Q.; Fu, P. Q.; Wang, Z. F.; Zhao, X. J.; Zhou, L. B.; Ji, D. S.; Wang, P. C.; Worsnop, D. R.

2015-12-01

The mitigation of air pollution in megacities remains a great challenge because of the complex sources and formation mechanisms of aerosol particles. The 2014 Asia-Pacific Economic Cooperation (APEC) summit in Beijing serves as a unique experiment to study the impacts of emission controls on aerosol composition, size distributions, and oxidation properties. Herein, a high-resolution time-of-flight aerosol mass spectrometer was deployed in urban Beijing for real-time measurements of size-resolved non-refractory submicron aerosol (NR-PM1) species from 14 October to 12 November 2014, along with a range of collocated measurements. The average (±σ) PM1 was 41.6 (±38.9) μg m-3 during APEC, which was decreased by 53 % compared with that before APEC. The aerosol composition showed substantial changes owing to emission controls during APEC. Secondary inorganic aerosol (SIA: sulfate + nitrate + ammonium) showed significant reductions of 62-69 %, whereas organics presented much smaller decreases (35 %). The results from the positive matrix factorization of organic aerosol (OA) indicated that highly oxidized secondary organic aerosol (SOA) showed decreases similar to those of SIA during APEC. However, primary organic aerosol (POA) from cooking, traffic, and biomass-burning sources were comparable to those before APEC, indicating the presence of strong local source emissions. The oxidation properties showed corresponding changes in response to OA composition. The average oxygen-to-carbon level during APEC was 0.36 (±0.10), which is lower than the 0.43 (±0.13) measured before APEC, demonstrating a decrease in the OA oxidation degree. The changes in size distributions of primary and secondary species varied during APEC. SIA and SOA showed significant reductions in large accumulation modes with peak diameters shifting from ~ 650 to 400 nm during APEC, whereas those of POA remained relatively unchanged. The changes in aerosol composition, size distributions, and oxidation

Aerosol composition, oxidative properties, and sources in Beijing: results from the 2014 Asia-Pacific Economic Cooperation Summit study

Science.gov (United States)

Xu, W. Q.; Sun, Y. L.; Chen, C.; Du, W.; Han, T. T.; Wang, Q. Q.; Fu, P. Q.; Wang, Z. F.; Zhao, X. J.; Zhou, L. B.; Ji, D. S.; Wang, P. C.; Worsnop, D. R.

2015-08-01

The mitigation of air pollution in megacities remains a great challenge because of the complex sources and formation mechanisms of aerosol particles. The 2014 Asia- Pacific Economic Cooperation (APEC) summit in Beijing serves as a unique experiment to study the impacts of emission controls on aerosol composition, size distributions, and oxidative properties. Herein, a high-resolution time-of-flight aerosol mass spectrometer was deployed in urban Beijing for real-time measurements of size-resolved non-refractory submicron aerosol (NR-PM1) species from 14 October to 12 November 2014, along with a range of collocated measurements. The average (±σ) PM1 was 41.6 (±38.9) μg m-3 during APEC, which was decreased by 53 % compared with that before APEC. The aerosol composition showed substantial changes owing to emission controls during APEC. Secondary inorganic aerosols (SIA = sulfate + nitrate + ammonium) showed significant reductions of 62-69 %, whereas organics presented much smaller decreases (35 %). The results from the positive matrix factorization of organic aerosols (OA) indicated that highly oxidized secondary OA (SOA) showed decreases similar to those of SIA during APEC. However, primary OA (POA) from cooking, traffic, and biomass burning sources were comparable to those before APEC, indicating the presence of strong local source emissions. The oxidation properties showed corresponding changes in response to OA composition. The average oxygen-to-carbon level during APEC was 0.36 (±0.10), which is lower than the 0.43 (±0.13) measured before APEC, demonstrating a decrease in the OA oxidation degree. The changes in size distributions of primary and secondary species varied during APEC. SIA and SOA showed significant reductions in large accumulation modes with peak diameters shifting from ~ 650 to 400 nm during APEC, whereas those of POA remained relatively unchanged. The changes in aerosol composition, size distributions, and oxidation degrees during the aging

Review of food composition data for edible insects.

Science.gov (United States)

Nowak, Verena; Persijn, Diedelinde; Rittenschober, Doris; Charrondiere, U Ruth

2016-02-15

Edible insects are considered rich in protein and a variety of micronutrients, and are therefore seen as potential contributors to food security. However, the estimation of the insects' contribution to the nutrient intake is limited since data are absent in food composition tables and databases. Therefore, FAO/INFOODS collected and published analytical data from primary sources with sufficient quality in the Food Composition Database for Biodiversity (BioFoodComp). Data were compiled for 456 food entries on insects in different developmental stages. A total of 5734 data points were entered, most on minerals and trace elements (34.8%), proximates (24.5%), amino acids (15.3%) and (pro)vitamins (9.1%). Data analysis of Tenebrio molitor confirms its nutritive quality that can help to combat malnutrition. The collection of data will assist compilers to incorporate more insects into tables and databases, and to further improve nutrient intake estimations. Copyright © 2015 Food and Agriculture Organization of the United Nations. Published by Elsevier Ltd.. All rights reserved.

Improving benchmarking by using an explicit framework for the development of composite indicators: an example using pediatric quality of care

OpenAIRE

Profit, Jochen; Typpo, Katri V; Hysong, Sylvia J; Woodard, LeChauncy D; Kallen, Michael A; Petersen, Laura A

2010-01-01

Abstract Background The measurement of healthcare provider performance is becoming more widespread. Physicians have been guarded about performance measurement, in part because the methodology for comparative measurement of care quality is underdeveloped. Comprehensive quality improvement will require comprehensive measurement, implying the aggregation of multiple quality metrics into composite indicators. Objective To present a conceptual framework to develop comprehensive, robust, and transp...

Influence of dietary lipid and protein sources on the sensory quality of organic rainbow trout (Oncorhynchus mykiss) after ice storage

DEFF Research Database (Denmark)

Green-Petersen, Ditte; Hyldig, Grethe; Jacobsen, Charlotte

2014-01-01

The influence of dietary protein and lipid sources on the quality of organic rainbow trout (Oncorhynchus mykiss) was studied. The protein and oil sources were fishmeal, fish oil, and organic vegetable protein and oils. Sensory profiling was performed during 3 to 14 days of ice storage along...... with lipid analyses of the fillet. Overall, the results showed that the sensory characteristics of the trout were affected in different ways during ice storage. The source of lipid seemed to affect the sensory quality at the beginning of the storage period, while the protein source seemed to have a more...

Well water quality in rural Nicaragua using a low-cost bacterial test and microbial source tracking.

Science.gov (United States)

Weiss, Patricia; Aw, Tiong Gim; Urquhart, Gerald R; Galeano, Miguel Ruiz; Rose, Joan B

2016-04-01

Water-related diseases, particularly diarrhea, are major contributors to morbidity and mortality in developing countries. Monitoring water quality on a global scale is crucial to making progress in terms of population health. Traditional analytical methods are difficult to use in many regions of the world in low-resource settings that face severe water quality issues due to the inaccessibility of laboratories. This study aimed to evaluate a new low-cost method (the compartment bag test (CBT)) in rural Nicaragua. The CBT was used to quantify the presence of Escherichia coli in drinking water wells and aimed to determine the source(s) of any microbial contamination. Results indicate that the CBT is a viable method for use in remote rural regions. The overall quality of well water in Pueblo Nuevo, Nicaragua was deemed unsafe, and results led to the conclusion that animal fecal wastes may be one of the leading causes of well contamination. Elevation and depth of wells were not found to impact overall water quality. However rope-pump wells had a 64.1% reduction in contamination when compared with simple wells.

Evaluating the composition and processing potential of novel sources of Brazilian biomass for sustainable biorenewables production.

Science.gov (United States)

Lima, Marisa A; Gomez, Leonardo D; Steele-King, Clare G; Simister, Rachael; Bernardinelli, Oigres D; Carvalho, Marcelo A; Rezende, Camila A; Labate, Carlos A; Deazevedo, Eduardo R; McQueen-Mason, Simon J; Polikarpov, Igor

2014-01-18

The search for promising and renewable sources of carbohydrates for the production of biofuels and other biorenewables has been stimulated by an increase in global energy demand in the face of growing concern over greenhouse gas emissions and fuel security. In particular, interest has focused on non-food lignocellulosic biomass as a potential source of abundant and sustainable feedstock for biorefineries. Here we investigate the potential of three Brazilian grasses (Panicum maximum, Pennisetum purpureum and Brachiaria brizantha), as well as bark residues from the harvesting of two commercial Eucalyptus clones (E. grandis and E. grandis x urophylla) for biofuel production, and compare these to sugarcane bagasse. The effects of hot water, acid, alkaline and sulfite pretreatments (at increasing temperatures) on the chemical composition, morphology and saccharification yields of these different biomass types were evaluated. The average yield (per hectare), availability and general composition of all five biomasses were compared. Compositional analyses indicate a high level of hemicellulose and lignin removal in all grass varieties (including sugarcane bagasse) after acid and alkaline pretreatment with increasing temperatures, whilst the biomasses pretreated with hot water or sulfite showed little variation from the control. For all biomasses, higher cellulose enrichment resulted from treatment with sodium hydroxide at 130°C. At 180°C, a decrease in cellulose content was observed, which is associated with high amorphous cellulose removal and 5-hydroxymethyl-furaldehyde production. Morphological analysis showed the effects of different pretreatments on the biomass surface, revealing a high production of microfibrillated cellulose on grass surfaces, after treatment with 1% sodium hydroxide at 130°C for 30 minutes. This may explain the higher hydrolysis yields resulting from these pretreatments, since these cellulosic nanoparticles can be easily accessed and cleaved by

Effect of Polymer Form and its Consolidation on Mechanical Properties and Quality of Glass/PBT Composites

DEFF Research Database (Denmark)

Raghavalu Thirumalai, Durai Prabhakaran; Pillai, Saju; Charca, Samuel

2014-01-01

different material systems included in this study; Glass/CBT (CBT160 powder based resin), Glass/PBT (prepreg tapes), and Glass/PBT (commingled yarns). The different types of thermoplastic polymer resin systems used for the manufacturing of the composite UD laminate dictate the differences in final......The aim of this study was to understand the role of the processing in determining the mechanical properties of glass fibre reinforced polybutylene terephthalate composites (Glass/PBT). Unidirectional (UD) composite laminates were manufactured by the vacuum consolidation technique using three...... mechanical properties which were evaluated by through compression, flexural and short beam transverse bending tests. Microscopy was used to evaluate the quality of the processed laminates, and fractography was used to characterize the observed failure modes. The study provides an improved understanding...

Single particle analysis of eastern Mediterranean aerosol particles: Influence of the source region on the chemical composition

Science.gov (United States)

Clemen, Hans-Christian; Schneider, Johannes; Köllner, Franziska; Klimach, Thomas; Pikridas, Michael; Stavroulas, Iasonas; Sciare, Jean; Borrmann, Stephan

2017-04-01

The Mediterranean region is one of the most climatically sensitive areas and is influenced by air masses of different origin. Aerosol particles are one important factor contributing to the Earth's radiative forcing, but knowledge about their composition and sources is still limited. Here, we report on results from the INUIT-BACCHUS-ACTRIS campaign, which was conducted at the Cyprus Atmospheric Observatory (CAO, Agia Marina Xyliatou) in Cyprus in April 2016. Our results show that the chemical composition of the aerosol particles in the eastern Mediterranean is strongly dependent on their source region. The composition of particles in a size range between 150 nm and 3 μm was measured using the Aircraft-based Laser ABlation Aerosol MAss spectrometer (ALABAMA), which is a single particle laser ablation instrument using a bipolar time-of-flight mass spectrometer. The mass spectral information on cations and anions allow for the analysis of different molecular fragments. The information about the source regions results from backward trajectories using HYSPLIT Trajectory Model (Trajectory Ensemble) on hourly basis. To assess the influence of certain source regions on the air masses arriving at CAO, we consider the number of trajectories that crossed the respective source region within defined time steps. For a more detailed picture also the height and the velocity of the air masses during their overpass above the source regions will be considered. During the campaign at CAO in April 2016 three main air mass source regions were observed: 1) Northern Central Europe, likely with an enhanced anthropogenic influence (e.g. sulfate and black carbon from combustion processes, fly ash particles from power plants, characterized by Sr and Ba), 2) Southwest Europe, with a higher influence of the Mediterranean Sea including sea salt particles (characterized by, e.g., NaxCly, NaClxNOy), 3) Northern Africa/Sahara, with air masses that are expected to have a higher load of mineral dust

Quality Assessment of Honey Sourced from Natural and Artificial Apiaries in Ekiti State, Nigeria.

Directory of Open Access Journals (Sweden)

Oyeyemi Sunday Dele

2017-10-01

Full Text Available Honey samples were obtained from wild and domesticated sources and analyzed for some physicochemical properties such as color, pH, moisture content, ash content, refractive index, specific gravity, total solid, viscosity, glucose and fructose content following Standard Association of Official Analytical Chemistry. The following range of values for pH (3.55-4.20, moisture content (18.50-25.60%, soluble solids (74.10-81.20%, ash content (0.08-0.14%, specific gravity (1.38-1.47, refractive index (81.3-83.4%, fructose content (40.5-63.04% and glucose content (19.35-32.34%. The mineral composition analyzed revealed potassium to be the dominant mineral in the honey samples followed by Calcium. However, Cadmium and lead where not detected in the honey samples. The results indicated that parameters such as pH, moisture content, ash content, specific gravity, sugar (majorly fructose and glucose content, fructose/glucose ratio, glucose/water ratio conform within the limit of the international standard for honey. However, moisture contents of the wild honey samples (22.05% and 25.60% were a little higher than the Codex Standards of ≤ 21%. In conclusion, the honey samples investigated have the needed quality criteria and are good for human consumption. The results also revealed excellent organoleptic acceptability of the honey samples, hence are suitable for human uses.

Egg quality and yolk lipid composition of laying hens fed diets containing cashew nut meal

Directory of Open Access Journals (Sweden)

Tatiana Fontoura Vidal

2013-03-01

Full Text Available The objective of this study was to assess the effect of the addition of cashew nuts meal (0, 5, 10, 15, 20, and 25% to laying hen diets on egg quality and yolk composition. The variables studied were: egg weight, specific gravity, Haugh Units, percentages of shell, albumen, and yolk, moisture, total solids, total lipids, fatty acids profile, and yolk cholesterol. The addition of up to 25% of cashew nuts meal to hen diets did not affect egg quality and freshness, moisture and total solids content. However, an increase in total lipid content and a decrease in yolk pigmentation was observed. Oleic acid level increased in the yolk, whereas palmitic, stearic, and linoleic acid levels decreased. The addition of cashew nuts meal increased the monounsaturated/saturated fatty acid ratio in the yolk and reduced the cholesterol content. Therefore, the use of cashew nuts meal in laying hen diets favorably modifies the fatty acid composition of egg yolk and contributes to a better acceptance of this food by consumers since it also reduces yolk cholesterol levels.

The Oxygen Isotopic Composition of Phosphate: A Tracer for Phosphate Sources and Cycling

Energy Technology Data Exchange (ETDEWEB)

Mclaughlin, K. [Southern California Coastal Water Research Project, Costa Mesa, University of California, CA (United States); Young, M. B.; Paytan, A.; Kendall, C. [U.S. Geological Survey, University of California, CA (United States)

2013-05-15

Phosphorus (P) is a limiting macro-nutrient for primary productivity and anthropogenic P-loading to aquatic ecosystems is one of the leading causes of eutrophication in many ecosystems throughout the world. Because P has only one stable isotope, traditional isotope techniques are not possible for tracing sources and cycling of P in aquatic systems. However, much of the P in nature is bonded to four oxygen (O) atoms as orthophosphate (PO{sub 4}{sup 3-}). The P-O bonds in orthophosphate are strongly resistant to inorganic hydrolysis and do not exchange oxygen with water without biological mediation (enzyme-mediated recycling). Thus, the oxygen isotopic composition of dissolved inorganic phosphate ({delta}{sup 18}O{sub p}) may be used as a tracer for phosphate sources and cycling in aquatic ecosystems. Recently, several studies have been conducted utilizing {delta}{sup 18}O{sub p} as a tracer for phosphate sources and cycling in various aquatic environments. Specifically, work to date indicates that {delta}{sup 18}O{sub p} is useful for determining sources of phosphate to aquatic systems if these sources have unique isotopic signatures and phosphate cycling within the system is limited compared to input fluxes. In addition, because various processes imprint specific fractionation effects, the {delta}{sup 18}O{sub p} tracer can be utilized to determine the degree of phosphorous cycling and processing through the biomass. This chapter reviews several of these studies and discusses the potential to utilize the {delta}{sup 18}O{sub p} of phosphate in rivers and streams. (author)

Guava: phytochemical composition of a potential source of antioxidants for cosmetic and/or dermatological applications

Directory of Open Access Journals (Sweden)

Bruna Galdorfini Chiari-Andréo

2017-06-01

Full Text Available ABSTRACT Guava (Psidium guajava L. is a native fruit of the American tropics with commercial applications for its taste, flavor and aroma. Numerous pharmacological uses have been described for it, such as the antiseptic effect of its leaves, the use of the fresh fruit and tea from its leaves for the treatment of diarrhea, dysentery, diabetes mellitus, and others. However, considering its rich composition, the guava also is a potential source of antioxidants to be used in the development of new formulations for cosmetic and/or dermatological applications, the main focus of this research. Herein, we describe the study of the phytochemical composition and the antioxidant activity of a guava extract prepared with non-toxic solvents aiming its use at biological applications. High performance liquid chromatography and mass spectrometry were employed to identify the major components, while thermoanalytical measurements and hot stage microscopy were used to assess the chemical stability of guava fruit extract. The antioxidant activity was also evaluated assessing the SOD-like activity and ABTS free radical scavenger. The results show that the extract is a rich source of phenolic compounds, such as quercetin, kaempferol, schottenol, among many others. All of the components found in guava extract exhibit biological effects according to the literature data, mainly antioxidant properties.

Effects of Funding Sources on Access to Quality Higher Education in Public Universities in Kenya: A Case Study

Directory of Open Access Journals (Sweden)

John Mutinda Mutiso

2015-04-01

Full Text Available In the last two decades, Kenya has witnessed an exponential growth of students’ enrolment in its public universities and an oscillatory government funding in these institutions precipitating quality concerns by employers on the skills of the graduates to meet industry needs. In education finance, the sources of funds and the size of the resources are key determinants of quality education. The objective of the study was to determine the relationship between various funding sources and access to quality education in Kenya public universities using a case approach. The data collection instruments used were an interview guide, a focus group discussion guide, a student’s survey questionnaire and secondary document analysis. Data was collected from October to December 2014 in the case university from a sample population of 10 top university management staff, 36 heads of department (HoDs and 400 undergraduate students. The study employed the education production function as a basic model of the study. The validity of the data collection instruments was established through scrutiny by thesis supervisors and the reliability test of the students’ questionnaire returned a cronbach alpha of 0.88. F-test and analysis of variance (ANOVA methods were used with aid of the statistical package for social science (SPSS version 2.0.The conclusion of the study was that, the sources of funds had a positive effect on quality though the results were not significant, while government capitation, tuition and other sources of funds were significantly important for the access of quality of education in the institution (P =0.30, P = 0.018, P = 0.000. The study recommended the adoption of performance based funding to enhance quality in higher education.

Canadian environmental sustainability indicators : air quality indicator : data sources methods 2005

International Nuclear Information System (INIS)

2006-01-01

National indicators of freshwater quality, air quality and greenhouse gas emissions were established in 2004 by the Canadian government in recognition that public health and economic well-being are linked to the quality of the environment. These indicators build on a base of an established national monitoring network and are communicated to the public by Environment Canada, Statistics Canada and Health Canada in an effort to provide reliable information on the state of the environment. Each indicator reported in a given year has an associated data sources and methods report to provide technical detail and background information that will help interpret the indicator. This particular report focused on the basic methods and data for the air quality indicator as it was reported in 2005. It approximated public exposure to ground-level ozone, a key component of smog and a harmful pollutant. Since ozone levels are influenced by weather and transboundary flows of pollutants, this report analyzed observed concentrations in relation to where people live. The indicator measures the seasonal average of the highest 8-hour average ground-level ozone concentration for each day. The indicator reflects possible health impacts related to ozone over the entire season. It is population-weighted and assumes that ozone concentrations are constant within a radius of 40 km around each monitoring station. It was noted that future improvements for the air quality indicator will include measures of fine particulate matter and improvements in monitoring methods. 9 refs., 2 tabs., 6 figs

CHANGE OF BIOCHEMICAL COMPOSITION OF PUMPKIN FRUITS DEPENDING ON STORAGE TIME

Directory of Open Access Journals (Sweden)

A. S. Karapetyan

2015-01-01

Full Text Available Pumpkin fruits are the source of carbohydrates, mineral salts and vitamins during wintertime. The change of the biochemical compositions of pumpkin fruits depending on storage time has been studied. The results of chemical analysis revealed that during four months of storage the content of quality indicators increased followed by its reduction after five and more month of storage. 

Maintaining Quality and Confidence in Open-Source, Evolving Software: Lessons Learned with PFLOTRAN

Science.gov (United States)

Frederick, J. M.; Hammond, G. E.

2017-12-01

Software evolution in an open-source framework poses a major challenge to a geoscientific simulator, but when properly managed, the pay-off can be enormous for both the developers and the community at large. Developers must juggle implementing new scientific process models, adopting increasingly efficient numerical methods and programming paradigms, changing funding sources (or total lack of funding), while also ensuring that legacy code remains functional and reported bugs are fixed in a timely manner. With robust software engineering and a plan for long-term maintenance, a simulator can evolve over time incorporating and leveraging many advances in the computational and domain sciences. In this positive light, what practices in software engineering and code maintenance can be employed within open-source development to maximize the positive aspects of software evolution and community contributions while minimizing its negative side effects? This presentation will discusses steps taken in the development of PFLOTRAN (www.pflotran.org), an open source, massively parallel subsurface simulator for multiphase, multicomponent, and multiscale reactive flow and transport processes in porous media. As PFLOTRAN's user base and development team continues to grow, it has become increasingly important to implement strategies which ensure sustainable software development while maintaining software quality and community confidence. In this presentation, we will share our experiences and "lessons learned" within the context of our open-source development framework and community engagement efforts. Topics discussed will include how we've leveraged both standard software engineering principles, such as coding standards, version control, and automated testing, as well unique advantages of object-oriented design in process model coupling, to ensure software quality and confidence. We will also be prepared to discuss the major challenges faced by most open-source software teams, such

Investigation on working quality of laser beam cutting of composite materials. Final report. Untersuchung der Bearbeitungsgenauigkeit und Prozessfuehrung beim Laserstrahlschneiden von Verbundwerkstoffen und Werkstoffverbunden. Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Geiger, M.; Mueller, R.

1992-01-01

Expanded use of composite materials often requires a cutting process to reach the desired shape of the work piece. In conventional mechanical cutting technologies like milling remarcable tool wear has to be considered due to the containing glass fibers which have a tremendous abrasive effect on the tool teeth. Here the laser beam is an alternative 'tool'. With this investigations the knowledge about the parameters of laser beam cutting of composites which determine working quality was increased. Requirements for an optimal cutting process and fundamental correlations between process parameters and working quality are presented. In absence of suitable criterions to estimate the working quality of laser beam cut composite materials, a suggestion of a DIN 2310, Part 7, 'Thermal Cutting, Laser Beam Cutting of Composites' is presented. (orig.) With 69 refs., 125 figs.

The demand for environmental quality in driving transitions to low-polluting energy sources

International Nuclear Information System (INIS)

Fouquet, Roger

2012-01-01

The purpose of this paper is to understand the long run demand for energy-related environmental quality, its influence on legislation and on transitions to low polluting energy sources. It presents a series of episodes in British history where a demand for improvements in energy-related environmental quality existed. These episodes helped to identify a few cases where markets partially drove transitions to low polluting energy sources, in specific economic conditions. More generally, they showed that, when pushed, governments will introduce environmental legislation, although it tends to be weak and poorly enforced. In the case of air pollution, strong and binding legislation occurred roughly one hundred years later than was socially optimal. Based on this evidence, for a transition to a low carbon economy, governments will probably need to introduce focussed and binding legislation, and this cannot be expected without strong and sustained demand for climate stability. This demand will need to be spearheaded by pressure groups to introduce legislation, to enforce it and to avoid it being over-turned by future governments. - Highlights: ► Reviews demand for improvements in environmental quality in British history. ► In special cases, demand may drive transitions through markets. ► Demand will probably have to drive transitions to low polluting energy through legislation. ► Need for strong and sustained demand spearheaded through pressure groups.

Environmental radiation control and quality management system in design and operation of sealed radioactive sources

International Nuclear Information System (INIS)

Hussein, A.Z.

2007-01-01

New environmental regulations and radiation safety standards are being implemented almost daily to ensure radiation safety, in particular for practices causing exposures to undue radiation doses. A particular emphasis of real challenge for organizations and users of radiation sources has to be for proper radiological safety assessment and is becoming cost effectively to be prepared for auditing. Special concern for the environment is of global . nature, and hence environmental auditing has been and will continue to be an essential practice for improving the environment and for meeting the relevant regulations and standards. In general, most facilities that deal with radioactive sources undertake strict safety measures in terms of personnel radiation protection, handling procedures and security. Hence, those measures should comply with the requirements of the environmental protection standards. Accordingly, a successful quality management system must balance realities of organization and personnel in achieving quality objectives. Organizational principles are found in the technical aspects of' quality management, such as, charting, requirements, measurements, procedures, ... , etc. Human principles are found in the communication side of quality management (e.g. meetings, ,decision making, ,teams, ... , etc). The quality management must understand and balance skills needed to blend them together. Large gamma irradiators present a high potential radiation hazard to the surrounding environment, since the amount of radioactivity is of the order of (P Bq) and a very high dose rates are produced during irradiation. Application of environmental radiation control deemed by regulatory authority and a proper quality management system by the utility would serve public health and safety

Composition and source of butyltins in sediments of Kaohsiung Harbor, Taiwan

Science.gov (United States)

Dong, Cheng-Di; Chen, Chih-Feng; Chen, Chiu-Wen

2015-04-01

Fifty-eight sediment samples were collected from the Kaohsiung Harbor (Taiwan) for analyses of monobutyltin (MBT), dibutyltin (DBT) and tributyltin (TBT), using gas chromatography/flame photometric detector (GC/FPD). The concentration of total butyltins (ΣBTs), sum of MBT, DBT, and TBT, varied from 3.9 to 158.5 ng Sn/g dw in sediment samples with TBT being the major component of the sediment samples, except for the vicinity of the Love River mouth where MBT was the most abundant BT compound (a proportion of over 57%). Based on the BTs concentration, distribution, composition and correlations, the sources of BTs found in harbor sediments are shipping activities, and TBT is the main pollutant; the estuary (i.e. Love River) has been the anthropogenic source of MBT from upstream inputs. Influences of TBT on aquatic organisms are evaluated using the toxicity guidelines proposed by the US EPA (US Environmental Protection Agency) and the ACCI (assessment class criterion for imposex) proposed by OSPAR (Oslo and Paris Commission). The evaluation shows that the TBT contained in the sediment at Kaohsiung Harbor is likely to have a negative influence at ACCI class C because gastropods present imposex and TBT levels are above ecotoxicological assessment criteria (EAC) limits.

Changes imposed by pyrolysis, thermal gasification and incineration on composition and phosphorus fertilizer quality of municipal sewage sludge

DEFF Research Database (Denmark)

Thomsen, Tobias Pape; Sárossy, Zsuzsa; Ahrenfeldt, Jesper

2017-01-01

Fertilizer quality of ash and char from incineration, gasification and pyrolysis of a single municipal sewage sludge sample were investigated by comparing composition and phosphorus (P) plant availability. A process for post oxidation of gasification ash and pyrolysis char was developed and the o......Fertilizer quality of ash and char from incineration, gasification and pyrolysis of a single municipal sewage sludge sample were investigated by comparing composition and phosphorus (P) plant availability. A process for post oxidation of gasification ash and pyrolysis char was developed...... and the oxidized materials were investigated as well. Sequential extraction with full elemental balances of the extracted pools as well as scanning electron microscopy with energy dispersive X-ray spectroscopy were used to investigate the mechanisms driving the observed differences in composition and P plant...... processes and 10–15% in pyrolysis whereas no reduction was observed in incineration processes. The influence on other heavy metals was less pronounced. The plant availability of P in the substrates varied from almost zero to almost 100% of the plant availability of P in the untreated sludge. Post-oxidized...

Properties of idealized designs of NB3SN composites

International Nuclear Information System (INIS)

Smathers, D.B.; Larbalestier, D.C.; Lee, P.J.; Marken, K.R.; McDonald, W.K.; O'Larey, P.M.

1985-01-01

A series of seven idealized bronze-Nb 3 Sn composites were manufactured by the MJR process with varying matrix to filament ratios and pure Nb and Nb 0.8 wt.% Ti cores. The central core of each composite was sealed by a diffusion barrier which results in each filament having an identical source of tin. Initial evaluations of the composites from critical current and transmission electron microscopy measurements are presented and their properties compared to standard MJR composites. The Nb 3 Sn current density does not appear to be a strong function of bronze to Nb ratio over the range 2.4 to 3.2:1. The standard MJR composites have higher critical current densities than the idealized composites. It is proposed that the major reason for the increased current density of the normal MJR conductors is the intrinsically higher quality of the filaments close to the central tin core. It is postulated that the high Sn content of the bronze surrounding these filaments leads to an intrinsically higher Nb 3 Sn filament current density

Characterization and Effects of Fiber Pull-Outs in Hole Quality of Carbon Fiber Reinforced Plastics Composite.

Science.gov (United States)

Alizadeh Ashrafi, Sina; Miller, Peter W; Wandro, Kevin M; Kim, Dave

2016-10-13

Hole quality plays a crucial role in the production of close-tolerance holes utilized in aircraft assembly. Through drilling experiments of carbon fiber-reinforced plastic composites (CFRP), this study investigates the impact of varying drilling feed and speed conditions on fiber pull-out geometries and resulting hole quality parameters. For this study, hole quality parameters include hole size variance, hole roundness, and surface roughness. Fiber pull-out geometries are quantified by using scanning electron microscope (SEM) images of the mechanically-sectioned CFRP-machined holes, to measure pull-out length and depth. Fiber pull-out geometries and the hole quality parameter results are dependent on the drilling feed and spindle speed condition, which determines the forces and undeformed chip thickness during the process. Fiber pull-out geometries influence surface roughness parameters from a surface profilometer, while their effect on other hole quality parameters obtained from a coordinate measuring machine is minimal.

Factors affecting reservoir and stream-water quality in the Cambridge, Massachusetts, drinking-water source area and implications for source-water protection

Science.gov (United States)

Waldron, Marcus C.; Bent, Gardner C.

2001-01-01

This report presents the results of a study conducted by the U.S. Geological Survey, in cooperation with the city of Cambridge, Massachusetts, Water Department, to assess reservoir and tributary-stream quality in the Cambridge drinking-water source area, and to use the information gained to help guide the design of a comprehensive water-quality monitoring program for the source area. Assessments of the quality and trophic state of the three primary storage reservoirs, Hobbs Brook Reservoir, Stony Brook Reservoir, and Fresh Pond, were conducted (September 1997-November 1998) to provide baseline information on the state of these resources and to determine the vulnerability of the reservoirs to increased loads of nutrients and other contaminants. The effects of land use, land cover, and other drainage-basin characteristics on sources, transport, and fate of fecal-indicator bacteria, highway deicing chemicals, nutrients, selected metals, and naturally occurring organic compounds in 11 subbasins that contribute water to the reservoirs also was investigated, and the data used to select sampling stations for incorporation into a water-quality monitoring network for the source area. All three reservoirs exhibited thermal and chemical stratification, despite artificial mixing by air hoses in Stony Brook Reservoir and Fresh Pond. The stratification produced anoxic or hypoxic conditions in the deepest parts of the reservoirs and these conditions resulted in the release of ammonia nitrogen orthophosphate phosphorus, and dissolved iron and manganese from the reservoir bed sediments. Concentrations of sodium and chloride in the reservoirs usually were higher than the amounts recommended by the U.S. Environmental Protection agency for drinking-water sources (20 milligrams per liter for sodium and 250 milligrams per liter for chloride). Maximum measured sodium concentrations were highest in Hobbs Brook Reservoir (113 milligrams per liter), intermediate in Stony Brook Reservoir (62

Influence of natural antioxidants on lipid composition of beef burgers submitted to irradiation in 60 Co source and electron beams

International Nuclear Information System (INIS)

Trindade, Reginaldo Almeida da

2007-01-01

Radiation processing has been employed in some countries as a mean of treatment to assure microbiological safety of meat and meat products, avoiding the occurrence of food-borne disease. The ionizing radiation may cause some undesirable changes on chemistry composition of food and the lipid oxidation is one of the main reactions. In meat products processing industry, the lipid composition is directly related to nutritional and sensory quality of the product. For preventing oxidation, use of antioxidants which can be synthetic or natural, has been practically applied in some products. Currently, most attention has been given to natural antioxidants from herbs and spices like rosemary and oregano. The aim this study was to assess the antioxidant effects of either rosemary and oregano extract in beef burgers submitted to irradiation in 60 Co source with dose 6, 7 e 8 kGy, electron beams with dose 3,5 e 7 kGy and storage under freeze along 0, 45 e 90 days. The results showed that rosemary extract has the major antioxidant effects when it is used on heterogeneous food matrix like beef burger, but oregano extract was better efficient to delay lipid oxidation along storage time when it is used in synergism with rosemary and/or BHT/BHA. Although to have occurred changes in the fatty acids composition it was not possible to demonstrate a straight dependence of irradiation dose and/or storage time. Sensory analysis showed that between the samples prepared with natural antioxidants, the beef burger prepared with oregano has received better scores by panelists. Irradiated beef burger prepared with rosemary has received better scores when compared to non-irradiated one. The use of spices with antioxidant activity to avoid the oxidative damage in foods that contain fats in their formulation is thought to be promising to application in food facilities. (author)

Aerosol sources and their contribution to the chemical composition of aerosols in the Eastern Mediterranean Sea during summertime

Directory of Open Access Journals (Sweden)

J. Sciare

2003-01-01

Full Text Available A detailed study on the temporal variability of compounds important in controlling aerosol chemical composition was performed during a one-month experiment conducted during summer 2000 at a background site on Crete, in the Eastern Mediterranean Sea. Contribution of different aerosol sources in the Eastern Mediterranean Basin could be investigated at this location since the site is influenced by a wide range of air masses originating mainly in Europe and Africa. Chemical apportionment was performed for various air mass origins and showed a strong impact of anthropogenic emissions in the Turkey and Central Europe sectors, with black carbon (BC and non-sea-salt sulfate (nss-SO4 concentrations higher than observed in the Eastern and Western Europe sectors. High levels of non-sea-salt calcium (nss-Ca were associated with air masses from Africa but also from Central Turkey. Evidence was found that BC calculation based on light absorbance during dust events was biased. This quality-controlled high temporal resolution dataset allowed to investigate in detail the source-receptor relationships responsible for the levels of BC, nss-SO4 and sulfur dioxide (SO2, observed in Crete. Among the results obtained from this model, the major contribution of Turkey and Central Europe was confirmed in terms of anthropogenic emissions. Comparisons with remote optical properties obtained from Satellite observations (SEAWIFS north of Crete indicates that our ground based aerosol characterization was suitable for describing aerosol properties in the atmospheric column for most of the time during the campaign.

Optimization of point sources on thin films using a statistical design approach. Application to {sup 60}Co sources; Optimisation des sources ponctuelles sur film mince par une approche experimentale de type plan d'experiences. Application aux sources de {sup 60}Co

Energy Technology Data Exchange (ETDEWEB)

Sanoit, J.; Leprince, B. [CEA Saclay, Dept. d' Instrumentation et de Metrologie des Rayonnements Ionisants, 91 - Gif sur Yvette (France); Vailhen, D. [CEA Saclay, Dir. de la Surete Nucleaire et de la Qualite, 91 - Gif sur Yvette (France)

2001-07-01

Radioactive point sources prepared by depositing weighed drops on thin membranes are commonly used in ionizing radiation metrology for 47{pi}{beta}-{gamma} coincidence counting or for low energy electrons spectrometry. The present study deals with the preparation of good quality sources having high detection yields. Some influential parameters on the source quality are studied using {sup 60}Co as radioactive tracer. An approach based on experimental statistical designs has been chosen. This approach allows us to obtain reliable results with a number of experiences lower than in the case of a systematic approach. Homogeneous {sup 60}Co sources with high metrological qualifies (R{sub {beta}}> 96 %) can be prepared using a direct deposit of {approx} 5 mg drops of {sup 60}Co solution ([Co] = 12 {mu}g/g, [HCl] = 0,5 mol/I) and dried at 60 deg C. The support of the radioactive spot is constituted with a gold coated (130 {mu}g/cm{sup 2} of Au) Vyns films (thickness 45 {mu}g/cm{sup 2}) on which a pad (diameter = 7 - 8 mm) of polystyrene microspheres (Estapor K-007) is prepared by an electro-spraying technique under 7,5 kV during 10 minutes. The alcoholic solution used for the electro-spraying step has the following chemical composition [Estapor K-007] 2.5 10{sup -2} wt % and [Tween 20] = 2.7 10{sup -2} wt %. (authors)

Image quality on dual-source computed-tomographic coronary angiography

International Nuclear Information System (INIS)

Rixe, Johannes; Rolf, Andreas; Conradi, Guido; Elsaesser, Albrecht; Moellmann, Helge; Nef, Holger M.; Hamm, Christian W.; Dill, Thorsten; Bachmann, Georg

2008-01-01

Multi-detector CT reliably permits visualization of coronary arteries, but due to the occurrence of motion artefacts at heart rates >65 bpm caused by a temporal resolution of 165 ms, its utilisation has so far been limited to patients with a preferably low heart rate. We investigated the assessment of image quality on computed tomography of coronary arteries in a large series of patients without additional heart rate control using dual-source computed tomography (DSCT). DSCT (Siemens Somatom Definition, 83-ms temporal resolution) was performed in 165 consecutive patients (mean age 64±11.4 years) after injection of 60-80 ml of contrast. Data sets were reconstructed in 5% intervals of the cardiac cycle and evaluated by two readers in consensus concerning evaluability of the coronary arteries and presence of motion and beam-hardening artefacts using the AHA 16-segment coronary model. Mean heart rate during CT was 65±10.5 bpm; visualisation without artefacts was possible in 98.7% of 2,541 coronary segments. Only two segments were considered unevaluable due to cardiac motion; 30 segments were unassessable due to poor signal-to-noise ratio or coronary calcifications (both n=15). Data reconstruction at 65-70% of the cardiac cycle provided for the best image quality. For heart rates >85 bpm, a systolic reconstruction at 45% revealed satisfactory results. Compared with earlier CT generations, DSCT provides for non-invasive coronary angiography with diagnostic image quality even at heart rates >65 bpm and thus may broaden the spectrum of patients that can be investigated non-invasively. (orig.)

RELIABLE DYNAMIC SOURCE ROUTING PROTOCOL (RDSRP FOR ENERGY HARVESTING WIRELESS SENSOR NETWORKS

Directory of Open Access Journals (Sweden)

B. Narasimhan

2015-03-01

Full Text Available Wireless sensor networks (WSNs carry noteworthy pros over traditional communication. Though, unkind and composite environments fake great challenges in the reliability of WSN communications. It is more vital to develop a reliable unipath dynamic source routing protocol (RDSRPl for WSN to provide better quality of service (QoS in energy harvesting wireless sensor networks (EH-WSN. This paper proposes a dynamic source routing approach for attaining the most reliable route in EH-WSNs. Performance evaluation is carried out using NS-2 and throughput and packet delivery ratio are chosen as the metrics.

Seasonal variability of PM2.5 composition and sources in the Klang Valley urban-industrial environment

Science.gov (United States)

Amil, Norhaniza; Talib Latif, Mohd; Firoz Khan, Md; Mohamad, Maznorizan

2016-04-01

This study investigates the fine particulate matter (PM2.5) variability in the Klang Valley urban-industrial environment. In total, 94 daily PM2.5 samples were collected during a 1-year campaign from August 2011 to July 2012. This is the first paper on PM2.5 mass, chemical composition and sources in the tropical environment of Southeast Asia, covering all four seasons (distinguished by the wind flow patterns) including haze events. The samples were analysed for various inorganic components and black carbon (BC). The chemical compositions were statistically analysed and the temporal aerosol pattern (seasonal) was characterised using descriptive analysis, correlation matrices, enrichment factor (EF), stoichiometric analysis and chemical mass closure (CMC). For source apportionment purposes, a combination of positive matrix factorisation (PMF) and multi-linear regression (MLR) was employed. Further, meteorological-gaseous parameters were incorporated into each analysis for improved assessment. In addition, secondary data of total suspended particulate (TSP) and coarse particulate matter (PM10) sampled at the same location and time with this study (collected by Malaysian Meteorological Department) were used for PM ratio assessment. The results showed that PM2.5 mass averaged at 28 ± 18 µg m-3, 2.8-fold higher than the World Health Organisation (WHO) annual guideline. On a daily basis, the PM2.5 mass ranged between 6 and 118 µg m-3 with the daily WHO guideline exceeded 43 % of the time. The north-east (NE) monsoon was the only season with less than 50 % sample exceedance of the daily WHO guideline. On an annual scale, PM2.5 mass correlated positively with temperature (T) and wind speed (WS) but negatively with relative humidity (RH). With the exception of NOx, the gases analysed (CO, NO2, NO and SO2) were found to significantly influence the PM2.5 mass. Seasonal variability unexpectedly showed that rainfall, WS and wind direction (WD) did not significantly correlate

Pb isotopic composition of the atmosphere of the Sao Paulo city, Brazil, and isotopic characterization of some pollutant sources

International Nuclear Information System (INIS)

Aily, C.; Babinski, M.; Ruiz, I.R.; Sato, K

2001-01-01

Lead isotopes are known to be good tools for surveying lead origin in atmospheric samples (Chow et al., 1975). Lead has four naturally occurring stable isotopes: 206 Pb, 207 Pb, 208 Pb and 204 Pb. The first three isotopes are end products of radioactive decay chains from 238 U, 235 U and 232 Th, respectively, and the last one is non-radiogenic. Therefore, their abundance and the ratios among the four isotopes gradually change with time. Lead in the atmosphere comes from various sources, such as leaded gasoline, industrial emissions and coal combustion. Thus, lead isotope ratios different from those of the mother rock in the region are often observed in the atmosphere (Tatsumoto and Patterson, 1963). Lead is emitted to the atmosphere in fine particles, which can be transported within air masses for very long distances, e. g. from mid latitude regions to the Artic and Antarctica (Sturges and Barrie, 1989). Lead isotopes have been used to trace the pollutant sources in many cities of the world. However, a systematic study using this methodology has not been done in any Brazilian city. The main purpose of the present work is to characterize the Pb isotope composition in the atmosphere in Sao Paulo city, and suggest the possible pollutant sources. For our study lead isotopes were measured in different samples: aerosols and rainwater which would yield the Pb isotope composition of the atmosphere. Samples of gasoline and ethanol, gutter sweepings, soot from vehicle exhaust pipes, and filters containing particulate material from industrial emissions were also analyzed, since they were considered potential pollutant sources of the atmosphere. In order to obtain the local geogenic Pb isotopic composition we also analyzed rock and K-feldspar samples. Lead concentrations were only determined on aerosols and rainwater samples (au)

Accounting for both local aquatic community composition and bioavailability in setting site-specific quality standards for zinc.

Science.gov (United States)

Peters, Adam; Simpson, Peter; Moccia, Alessandra

2014-01-01

Recent years have seen considerable improvement in water quality standards (QS) for metals by taking account of the effect of local water chemistry conditions on their bioavailability. We describe preliminary efforts to further refine water quality standards, by taking account of the composition of the local ecological community (the ultimate protection objective) in addition to bioavailability. Relevance of QS to the local ecological community is critical as it is important to minimise instances where quality classification using QS does not reconcile with a quality classification based on an assessment of the composition of the local ecology (e.g. using benthic macroinvertebrate quality assessment metrics such as River InVertebrate Prediction and Classification System (RIVPACS)), particularly where ecology is assessed to be at good or better status, whilst chemical quality is determined to be failing relevant standards. The alternative approach outlined here describes a method to derive a site-specific species sensitivity distribution (SSD) based on the ecological community which is expected to be present at the site in the absence of anthropogenic pressures (reference conditions). The method combines a conventional laboratory ecotoxicity dataset normalised for bioavailability with field measurements of the response of benthic macroinvertebrate abundance to chemical exposure. Site-specific QSref are then derived from the 5%ile of this SSD. Using this method, site QSref have been derived for zinc in an area impacted by historic mining activities. Application of QSref can result in greater agreement between chemical and ecological metrics of environmental quality compared with the use of either conventional (QScon) or bioavailability-based QS (QSbio). In addition to zinc, the approach is likely to be applicable to other metals and possibly other types of chemical stressors (e.g. pesticides). However, the methodology for deriving site-specific targets requires

Aerosol composition and source apportionment in Santiago de Chile

International Nuclear Information System (INIS)

Artaxo, Paulo; Oyola, Pedro; Martinez, Roberto

1999-01-01

Santiago de Chile, Sao Paulo and Mexico City are Latin American urban areas that suffer from heavy air pollution. In order to study air pollution in Santiago area, an aerosol source apportionment study was designed to measure ambient aerosol composition and size distribution for two downtown sampling sites in Santiago. The aerosol monitoring stations were operated in Gotuzo and Las Condes during July and August 1996. The study employed stacked filter units (SFU) for aerosol sampling, collecting fine mode aerosol (dp 10 mass of particles smaller than 10 μm) and black carbon concentration were also measured. Particle-Induced X-ray Emission (PIXE) was used to measure the concentration of 22 trace elements at levels below 0.5 ng m -3 . Quantitative aerosol source apportionment was performed using Absolute Principal Factor Analysis (APFA). Very high aerosol concentrations were observed (up to 400 μg/m 3 PM 10 ). The main aerosol particle sources in Santiago are resuspended soil dust and traffic emissions. Coarse particles account for 63% of PM 10 aerosol in Gotuzo and 53% in Las Condes. A major part of this component is resuspended soil dust. In the fine fraction, resuspended soil dust accounts for 15% of fine mass, and the aerosols associated with transportation activities account for a high 64% of the fine particle mass. Sulfate particle is an important component of the aerosol in Santiago, mainly originating from gas-to-particle conversion from SO 2 . In the Gotuzo site, sulfates are the highest aerosol component, accounting for 64.5% of fine mass. Direct traffic emissions are generally mixed with resuspended soil dust. It is difficult to separate the two components, because the soil dust in downtown Santiago is contaminated with Pb, Br, Cl, and other heavy metals that are also tracers for traffic emissions. Residual oil combustion is observed, with the presence of V, S and Ni. An aerosol components from industrial emissions is also present, with the presence of

Z-Source-Inverter-Based Flexible Distributed Generation System Solution for Grid Power Quality Improvement

DEFF Research Database (Denmark)

Blaabjerg, Frede; Vilathgamuwa, D. M.; Loh, Poh Chiang

2009-01-01

Distributed generation (DG) systems are usually connected to the grid using power electronic converters. Power delivered from such DG sources depends on factors like energy availability and load demand. The converters used in power conversion do not operate with their full capacity all the time......-stage buck-boost inverter, recently proposed Z-source inverter (ZSI) is a good candidate for future DG systems. This paper presents a controller design for a ZSI-based DG system to improve power quality of distribution systems. The proposed control method is tested with simulation results obtained using...

MILK QUALITY OF DAIRY GOAT BY GIVING FEED SUPPLEMENT AS ANTIOXIDANT SOURCE

Directory of Open Access Journals (Sweden)

Mardalena

2011-09-01

Full Text Available Free radical levels can be higher than the level of endogenous antioxidants in the body so that uncomfortable conditions in the body of dairy goats could happen. To anticipate this uncomfortable conditions will be given feed supplement (FS as source of antioxidants (AOX. FS contain mixture pineapple rind meal and antioxidant minerals (AOXM each 25 ppm Zn and 10 ppm Cu. This experiment was carried out to investigate the effect of feed supplements as antioxidant source on milk quality of dairy goats. Sixteen Etawah dairy goats in the second lactation were used in the experiment that conducted using randomized block design with 4 treatments and 4 replicates. The treatments were R0 (grass + concentrate, R1 (R0 + FS containing 0.04 % AOX, R2 (R0 + FS containing 0.06% AOX, R3 (R0 + FS containing 0.08 % AOX. The data collected were analyzed using Anova. The result of phytochemicals analysis indicated that feed supplement contained flavonoid, polyphenols, sesqiuterpen, mopnoterpen, steroids, quinones and saponins. The results of study showed that there were difference (p0.05 on milk yield, milk fat, milk protein and milk antioxidant. The conclusion of this study was the feed supplements containing 0.08 AOX produced the best response to milk quality of dairy goats.

Quality Analysis of DNA from Cord Blood Buffy Coat: The Best Neonatal DNA Source for Epidemiological Studies?

Science.gov (United States)

Zhou, Guangdi; Li, Qin; Huang, Lisu; Wu, Yuhang; Wu, Meiqin; Wang, Weiye C

2016-04-01

Umbilical cord blood is an economical and easy to obtain source of high-quality neonatal genomic DNA. However, although large numbers of cord blood samples have been collected, information on the yield and quality of the DNA extracted from cord blood is scarce. Moreover, considerable doubt still exists on the utility of the buffy coat instead of whole blood as a DNA source. We compared the sample storage and DNA extraction costs for whole blood, buffy coat, and all-cell pellet. We evaluated three different DNA purification kits and selected the most suitable one to purify 1011 buffy coat samples. We determined the DNA yield and optical density (OD) ratios and analyzed 48 single-nucleotide polymorphisms using time-of-flight mass spectrometry (TOF MS). We also analyzed eight possible preanalytical variables that may correlate with DNA yield or quality. Buffy coat was the most economical and least labor-intensive source for sample storage and DNA extraction. The average yield of genomic DNA from 200 μL of buffy coat sample was 16.01 ± 8.00 μg, which is sufficient for analytic experiments. The mean A260/A280 ratio and the mean A260/A230 ratio were 1.89 ± 0.09 and 1.95 ± 0.66, respectively. More than 99.5% of DNA samples passed the TOF MS test. Only hemolysis showed a strong correlation with OD ratios of DNA, but not with yield. Our findings show that cord blood buffy coat yields high-quality DNA in sufficient quantities to meet the requirements of experiments. Buffy coat was also found to be the most economic, efficient, and stable source of genomic DNA.

Valuing the Potential Benefits of Water Quality Improvements in Watersheds Affected by Non-Point Source Pollution

Directory of Open Access Journals (Sweden)

Sergio Alvarez

2016-03-01

Full Text Available Nonpoint source (NPS pollution has been identified by the US Environmental Protection Agency (EPA as “the nation’s largest water quality problem”. Urban development, septic systems, and agricultural operations have been identified as the major sources of diffuse pollution in surface and ground water bodies. In recent decades, urban and agricultural Best Management Practices (BMP have been developed in several states to address agricultural water quality and water use impacts, including the reduction of nutrient loads to help meet water quality standards. Compliance with BMPs is associated with some costs to local governments, homeowners, and agricultural operations, but the improvements in water quality associated with BMP adoption are expected to yield significant benefits to society in the form of improved recreational opportunities, navigation, flood control, and ecosystem health. The development of sound policies and decision making processes require balancing the costs of BMP adoption to the agricultural operations with the social benefits to be derived from the improved water quality. In this paper we develop a benefits transfer model to provide estimates of the economic benefits of properly implemented and effective Best Management Practices (BMP throughout the state of Florida. These benefit estimates can be used in a cost-benefit framework to determine the optimal level of BMP adoption throughout the state of Florida and provide a framework for other regions to estimate the potential benefits of BMP-mediated water quality improvements.

Short communication. Effects of adding different protein and carbohydrates sources on chemical composition and in vitro gas production of corn stover silage

Directory of Open Access Journals (Sweden)

L. A. Mejía-Uribe

2013-05-01

Full Text Available The use of protein-rich by-products based in swine manure (SM, poultry waste (PW or chemicals compounds as urea (U, as well as energy products like molasses (M and bakery by-product (BB, is a viable method to produce good quality silage. In addition, the use of a bacterial additive can improve the fermentation characteristics of silage. The objective of this study was to determine chemical composition, in vitro gas production (GP and dry matter disappearance (DMd, using different sources of protein and energy in silage. The silages were made using SM, PW or U as protein sources and M or BB as energy source, with corn stover and with or without a bacterial additive. The organic matter (OM content was higher (p < 0.001 in silages with UBB, UM and SMBB compared with the rest of the treatments; meanwhile crude protein content was higher (p < 0.001 in silages with U. The addition of a bacterial additive increased (p < 0.05 OM content and decreased (p < 0.05 fiber content. Total GP was higher (p < 0.05 in silages containing BB, but DMd was higher (p < 0.05 in silages with U and SMBB. The inclusion of a bacterial additive decreased (p < 0.05 GP and DMd. The use of alternative sources of protein such as poultry and swine manure or urea, and of by-products of sugar industry and bakery is an alternative for silages based on corn stover. The results show that when properly formulated, the silages can provide more than 16% of crude protein and have DMd values above 60%.

The correlationship between the metabolizable energy content, chemical composition and color score in different sources of corn DDGS.

Science.gov (United States)

Jie, Yong-Z; Zhang, Jian-Y; Zhao, Li-H; Ma, Qiu-G; Ji, Cheng

2013-09-25

This study was conducted to evaluate the apparent metabolizable energy (AME) and true metabolizable energy (TME) contents in 30 sources of corn distillers dried grains with solubles (DDGS) in adult roosters, and establish the prediction equations to estimate the AME and TME value based on its chemical composition and color score. Twenty-eight sources of corn DDGS made from several processing plants in 11 provinces of China and others imported from the United States. DDGS were analyzed for their metabolizable energy (ME) contents, measured for color score and chemical composition (crude protein, crude fat, ash, neutral detergent fiber, acid detergent fiber), to predict the equation of ME in DDGS. A precision-fed rooster assay was used, each DDGS sample was tube fed (50 g) to adult roosters. The experiment was conducted as a randomized incomplete block design with 3 periods. Ninety-five adult roosters were used in each period, with 90 being fed the DDGS samples and 5 being fasted to estimate basal endogenous energy losses. Results showed that the AME ranged from 5.93 to 12.19 MJ/kg, TME ranged from 7.28 to 13.54 MJ/kg. Correlations were found between ME and ash content (-0.64, P sources energy digestibility and metabolizable energy content.

Experimental study of surface quality and damage when drilling unidirectional CFRP composites

Directory of Open Access Journals (Sweden)

Eshetu D. Eneyew

2014-10-01

Full Text Available In this study, an experimental investigation on the drilling of unidirectional carbon fiber reinforced plastic (UD-CFRP composite was conducted using polycrystalline diamond (PCD tipped eight facet drill. The quality of the drilled hole surface was examined through surface roughness measurements and surface damage by scanning electron microscopy (SEM. It was found that fiber pullout occurred in two specific sectors relative to the angle between the cutting direction and the fiber orientation. The thrust force was highly influenced by the feed rate than the cutting speed and it shows a significant variation throughout the rotation of the drill.

Effects of ractopamine hydrochloride and immunological castration in pigs. Part 2: belly quality characteristics and fatty acid composition

Directory of Open Access Journals (Sweden)

Letícia Cristina COSTA E SILVA

Full Text Available Abstract The effects of immunocastration and ractopamine in the diet on the belly quality were investigated from two crossbred pigs under different conditions of production, diet, management, and slaughter arranged in factorial design using two levels of addition of ractopamine in the diet, 0 and 7.5 ppm, and three genders (gilts, immunocastrated and barrows. The quality of bellies were analyzed for chemical composition, pH, meat and fat color, backfat thickness and fatty acid profile of the fat. The addition of ractopamine showed no significant influence on pH, color and chemical composition in two crossbred pigs. The immunocastrated had thicker belly backfat compared to the bellies of the gilts. The contents of fatty acids polyunsaturated, linoleic, linoleic, arachidonic, total omega 3 and omega 6 were higher for immunocastrated pigs, as well as presenting values greater than 0.4 for the PUFA:SFA ratio, thus, providing bellies with better nutritional quality. The bellies of the gilts and immunocastrated pigs had higher concentrations of iodine value, indicative of higher unsaturated fat content. The results indicated that the addition of ractopamine and immunocastration had little influence on the quality of bellies as well as in their fatty acid profiles, suggesting the continuity of implementation of these techniques.

Cascading influence of inorganic nitrogen sources on DOM production, composition, lability and microbial community structure in the open ocean.

Science.gov (United States)

Goldberg, S J; Nelson, C E; Viviani, D A; Shulse, C N; Church, M J

2017-09-01

Nitrogen frequently limits oceanic photosynthesis and the availability of inorganic nitrogen sources in the surface oceans is shifting with global change. We evaluated the potential for abrupt increases in inorganic N sources to induce cascading effects on dissolved organic matter (DOM) and microbial communities in the surface ocean. We collected water from 5 m depth in the central North Pacific and amended duplicate 20 liter polycarbonate carboys with nitrate or ammonium, tracking planktonic carbon fixation, DOM production, DOM composition and microbial community structure responses over 1 week relative to controls. Both nitrogen sources stimulated bulk phytoplankton, bacterial and DOM production and enriched Synechococcus and Flavobacteriaceae; ammonium enriched for oligotrophic Actinobacteria OM1 and Gammaproteobacteria KI89A clades while nitrate enriched Gammaproteobacteria SAR86, SAR92 and OM60 clades. DOM resulting from both N enrichments was more labile and stimulated growth of copiotrophic Gammaproteobacteria (Alteromonadaceae and Oceanospirillaceae) and Alphaproteobacteria (Rhodobacteraceae and Hyphomonadaceae) in weeklong dark incubations relative to controls. Our study illustrates how nitrogen pulses may have direct and cascading effects on DOM composition and microbial community dynamics in the open ocean. © 2017 Society for Applied Microbiology and John Wiley & Sons Ltd.

Investigation of the composition of an ion beam produced using a multi arc ion source

Energy Technology Data Exchange (ETDEWEB)

Engelko, V [Efremov Institute of Electrophysical Apparatus, St. Petersburg (Russian Federation); Giese, H; Schalk, S [Forschungszentrum Karlsruhe (Germany). INR; Mishin, M; Tsibin, O Y [St. Petersburg State Technical Univ. (Russian Federation)

1997-12-31

Complementing the diode and beam transport optimization studies currently performed at FZK Karlsruhe on the proton-beam-facility PROFA, supplementary investigations were run at the St. Petersburg State University, focusing on ion beam divergence and composition measurements using the TOF techniques. To ensure direct transferability of the results to the PROFA facility, these measurements were made on a scaled-down replica of the PROFA diode, comprising an array of small polyethylene flash-over plasma sources and a grid extraction system. Only the results of the beam composition measurements are presented, and the following conclusions are made: (i) The ion beam contains H and C ions and heavier constituents that remain to be identified. (ii) The beam composition changes significantly with the total number of shots: While H{sup +} ions predominated in the starting phase of the experiments, heavier components outweighed them later on, presumably due to hydrogen depletion of the surface layer of the anode polyethylene units. (iii) Reconditioning of the polyethylene units may be possible by running the diode at higher currents (self-cleaning) or by cutting off a surface layer. (author). 7 figs., 3 refs.

Structural and physico-mechanical properties of natural rubber/GTR composites devulcanized by microwaves: influence of GTR source and irradiation time

OpenAIRE

Colom Fajula, Xavier; Marin-Genesca, Marc; Mujal Rosas, Ramón María; Formela, Krzysztof; Cañavate Ávila, Francisco Javier

2018-01-01

Ground tire rubber from car and truck was modified using microwave irradiation at variable time. The irradiated ground tire rubber was used as filler in composites based on natural rubber. The composites, with high content of ground tire rubber, were prepared using an internal batch mixer and subsequently cross-linked at 160¿. The influence of the ground tire rubber source (car/truck) and irradiation time on structure, physico-mechanical behaviour, thermal properties and morphology of natural...

Biofilm composition in the Olt River (Romania) reservoirs impacted by a chlor-alkali production plant.

Science.gov (United States)

Dranguet, P; Cosio, C; Le Faucheur, S; Hug Peter, D; Loizeau, J-L; Ungureanu, V-Gh; Slaveykova, V I

2017-05-24

Freshwater biofilms can be useful indicators of water quality and offer the possibility to assess contaminant effects at the community level. The present field study examines the effects of chlor-alkali plant effluents on the community composition of biofilms grown in the Olt River (Romania) reservoirs. The relationship between ambient water quality variables and community composition alterations was explored. Amplicon sequencing revealed a significant modification of the composition of microalgal, bacterial and fungal communities in the biofilms collected in the impacted reservoirs in comparison with those living in the uncontaminated control reservoir. The abundance corrected Simpson index showed lower richness and diversity in biofilms collected in the impacted reservoirs than in the control reservoir. The biofilm bacterial communities of the impacted reservoirs were characterized by the contaminant-tolerant Cyanobacteria and Bacteroidetes, whereas microalgal communities were predominantly composed of Bacillariophyta and fungal communities of Lecanoromycetes and Paraglomycetes. A principal component analysis revealed that major contaminants present in the waste water of the chlor-alkali production plant, i.e. Na + , Ca 2+ , Cl - and Hg, were correlated with the alteration of biofilm community composition in the impacted reservoirs. However, the biofilm composition was also influenced by water quality variables such as NO 3 - , SO 4 2- , DOC and Zn from unknown sources. The results of the present study imply that, even when below the environmental quality standards, typical contaminants of chlor-alkali plant releases may affect biofilm composition and that their impacts on the microbial biodiversity might be currently overlooked.

Effects of gestational maternal undernutrition on growth, carcass composition and meat quality of rabbit offspring.

Science.gov (United States)

Symeon, George K; Goliomytis, Michael; Bizelis, Iosif; Papadomichelakis, George; Pagonopoulou, Olga; Abas, Zafeiris; Deligeorgis, Stelios G; Chadio, Stella E

2015-01-01

An experiment was conducted in order to evaluate the effects of gestational undernutrition of rabbit does on growth, carcass composition and meat quality of the offsprings. Thirty primiparous non lactating rabbit does were artificially inseminated and randomly divided in three treatment groups: Control (C; fed to 100% of maintenance requirements throughout gestation, n = 10), early undernourished (EU; fed to 50% of maintenance requirements during days 7-19 of gestation, n = 10) and late undernourished (LU; fed to 50% of maintenance requirements during days 20-27 of gestation, n = 10). During the 4th week of the gestation period, LU does significantly lost weight compared to C and EU groups (Ptotal litter size (alive and stillborn kits) was not different among groups (10.7, 12.8 and 12.7 kits in C, EU and LU groups, respectively). Kit birth weight tended to be lower in the LU group. During fattening, body weight and feed intake were not different among offsprings of the three experimental groups. Moreover, the maternal undernutrition did not have any impact on carcass composition of the offsprings in terms of carcass parts and internal organs weights as well as meat quality of L. lumborum muscle (pH24, colour, water holding capacity and shear values) at slaughter (70 days of age). Therefore, it can be concluded that the gestational undernutrition of the mother does not have detrimental effects on the productive and quality traits of the offsprings.

Aerosol composition and source apportionment in Santiago de Chile

Science.gov (United States)

Artaxo, Paulo; Oyola, Pedro; Martinez, Roberto

1999-04-01

Santiago de Chile, São Paulo and Mexico City are Latin American urban areas that suffer from heavy air pollution. In order to study air pollution in Santiago area, an aerosol source apportionment study was designed to measure ambient aerosol composition and size distribution for two downtown sampling sites in Santiago. The aerosol monitoring stations were operated in Gotuzo and Las Condes during July and August 1996. The study employed stacked filter units (SFU) for aerosol sampling, collecting fine mode aerosol (dpsource apportionment was performed using Absolute Principal Factor Analysis (APFA). Very high aerosol concentrations were observed (up to 400 μg/m 3 PM 10). The main aerosol particle sources in Santiago are resuspended soil dust and traffic emissions. Coarse particles account for 63% of PM 10 aerosol in Gotuzo and 53% in Las Condes. A major part of this component is resuspended soil dust. In the fine fraction, resuspended soil dust accounts for 15% of fine mass, and the aerosols associated with transportation activities account for a high 64% of the fine particle mass. Sulfate particle is an important component of the aerosol in Santiago, mainly originating from gas-to-particle conversion from SO 2. In the Gotuzo site, sulfates are the highest aerosol component, accounting for 64.5% of fine mass. Direct traffic emissions are generally mixed with resuspended soil dust. It is difficult to separate the two components, because the soil dust in downtown Santiago is contaminated with Pb, Br, Cl, and other heavy metals that are also tracers for traffic emissions. Residual oil combustion is observed, with the presence of V, S and Ni. An aerosol components from industrial emissions is also present, with the presence of several heavy metals such as Zn, Cu and others. A factor with molybdenum, arsenic, copper and sulfur was observed frequently, and it results from emissions of copper smelters.

Composite materials pipings: selection of basic materials and manufacturing process, quality control during manufacture

International Nuclear Information System (INIS)

Pays, M.F.

1997-01-01

The purpose of the paper is to present a summary of the knowledge acquired at the R and D on resins used as composite matrix, the resistance to hydrolysis and mechanical strength of pipings made from these materials, and on quality control during manufacture. The initial targets concerning the material selection, industrial manufacturing and quality control procedures are presented. The paper describes the results obtained concerning the investigation of the damage produced by hydrolysis in polyesters, vinyl esters and epoxides, the influence of temperature, reinforcement and the mechanical characterization of the tubing manufacturing. The performances of the nondestructive testings (radiography, ultrasonic controls, differential interferometry and infrared thermography) used are also reported. The paper ends with a further research and testings programme. (author)

Consideration of insects as a source of dietary protein for human consumption.

Science.gov (United States)

Churchward-Venne, Tyler A; Pinckaers, Philippe J M; van Loon, Joop J A; van Loon, Luc J C

2017-12-01

Consumption of sufficient dietary protein is fundamental to muscle mass maintenance and overall health. Conventional animal-based protein sources such as meat (ie, beef, pork, lamb), poultry, fish, eggs, and dairy are generally considered high-quality sources of dietary protein because they meet all of the indispensable amino-acid requirements for humans and are highly digestible. However, the production of sufficient amounts of conventional animal-based protein to meet future global food demands represents a challenge. Edible insects have recently been proposed as an alternative source of dietary protein that may be produced on a more viable and sustainable commercial scale and, as such, may contribute to ensuring global food security. This review evaluates the protein content, amino-acid composition, and digestibility of edible insects and considers their proposed quality and potential as an alternative protein source for human consumption. © The Author(s) 2017. Published by Oxford University Press on behalf of the International Life Sciences Institute. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Drinking water treatment plant costs and source water quality: An updated case study (2013-2016)

Science.gov (United States)

Watershed protection can play an important role in producing safe drinking water. However, many municipalities and drinking water treatment plants (DWTPs) lack the information on the potential benefits of watershed protection as an approach to improving source water quality. This...

A second look into fibre typing--relation to meat quality.

Science.gov (United States)

Lefaucheur, L

2010-02-01

Despite intensive research, a large variation in meat quality is still observed in most meat producing species. It is widely accepted that myofibre type composition is an important source of variation in meat quality. However, the identification of specific and universal relationships between myofibre characteristics, growth performance and meat quality traits remains a challenge. After the presentation of recent knowledge underlying fibre typing, this review describes the involvements of Ca2+-dependent mechanisms, and the energy state of the myofibres in the control of contractile and metabolic properties, with a special attention to the AMP-activated protein kinase pathway and mitochondrial compartment. In order to identify muscle components which could mask specific relationships between fibre type composition and meat quality, an analysis of the interactions between myofibres and other muscle cellular components is presented. After a brief description of myogenesis, the significance of the total number of fibres, myofibre cross-sectional area and fibre type composition for growth performance and meat quality is presented. Then, some genetic and environmental factors are proposed as possible tools to control meat quality trough the modulation of fibre type characteristics. Finally, a conclusion makes the point on bottlenecks still preventing the identification of specific relationships between fibre characteristics, growth performance and meat quality, and suggests future perspectives such as direct selection on fibre traits and study of correlated responses, the development of in vitro approaches using cell cultures, manipulation of myogenesis during the fetal period, and the production and use of genetically modified animals.

Chemical composition and water quality of Tashlyk Water-cooling reservoir of South-Ukraine NPP

International Nuclear Information System (INIS)

Kosheleva, S.I.; Gajdar, E.M.

1995-01-01

Information about water quality in Tashlyk water reservoir (cooler of South-Ukrainian NPP) during 9 years (1980-1992) is presented. Comparative data about Water Quality of South Bug (its source of water nutrition) and this reservoir point on the periodical pollution by surface waters and industrial wastes with a great contain of sulphates and chlorides. The class of water has been changed from hydrocarbonat calcium to sulfur-chlorine-magnesium or chlorine-natrium. The contain of biogenic and organic components in reservoir's water has been corresponded to the main class of waters satisfactory cleanliness

Composição química, produção e qualidade do café fertilizado com diferentes fontes e doses de nitrogênio Chemical composition, yield and quality of the fertilized coffee with different sources and doses of nitrogen

Directory of Open Access Journals (Sweden)

Marcelo Ribeiro Malta

2003-12-01

response of yield to N sources and doses. Coffee quality reduction was observed when calcium nitrate and ammonium nitrate were used. Regarding the doses used, the N sources presented differentiated effects on the coffee quality; however, it was observed by the analyses of the polyphenoloxidase activity, total titrable acidity, total chlorogenic acids and total phenolic compounds, that higher doses of ammonium sulphate had a negative effect on both chemical composition and quality of the grain.

Seed source, seed traits, and frugivore habits: Implications for dispersal quality of two sympatric primates.

Science.gov (United States)

Benítez-Malvido, Julieta; González-Di Pierro, Ana Ma; Lombera, Rafael; Guillén, Susana; Estrada, Alejandro

2014-06-01

• Premise of the study: Frugivore selection of fruits and treatment of seeds together with seed deposition site are crucial for the population dynamics of vertebrate-dispersed plants. However, frugivore species may influence dispersal quality differently even when feeding on the same fruit species and, while animals disperse some seeds, others simply fall beneath the parent plant.• Methods: In southern Mexico, we investigated to see if within-species seed traits (i.e., length, width, weight, and volume) and germination success differed according to seed source. For five tropical tree species we obtained ingested seeds from two sources, howler monkey (Alouatta pigra) and spider monkey (Ateles geoffroyi) feces; and noningested seeds from two sources, the ground and tree crowns (with predispersed seeds used as control).• Key results: A principal components' analysis showed that traits of seeds ingested by howler monkeys differed from other sources while seeds ingested by spider monkeys were similar to noningested seeds. Howlers consumed on average the larger seeds in Ampelocera hottlei, Brosimum lactescens, and Dialium guianense. Both primate species consumed the smaller seeds in Spondias mombin, while no seed trait differences among seed sources were found in Spondias radlkoferi. For all five tree species, germination rate was greatest for seeds ingested by howler monkeys.• Conclusions: For the studied plant species, seed ingestion by howler monkeys confers higher dispersal quality than ingestion by spider monkeys or nondispersal. Dispersal services of both primate species, however, are not redundant and may contribute to germination heterogeneity within plant populations in tropical forests. © 2014 Botanical Society of America, Inc.

A scanning point source for quality control of FOV uniformity in GC-PET imaging

International Nuclear Information System (INIS)

Bergmann, H.; Minear, G.; Dobrozemsky, G.; Nowotny, R.; Koenig, B.

2002-01-01

Aim: PET imaging with coincidence cameras (GC-PET) requires additional quality control procedures to check the function of coincidence circuitry and detector zoning. In particular, the uniformity response over the field of view needs special attention since it is known that coincidence counting mode may suffer from non-uniformity effects not present in single photon mode. Materials and methods: An inexpensive linear scanner with a stepper motor and a digital interface to a PC with software allowing versatile scanning modes was developed. The scanner is used with a source holder containing a Sodium-22 point source. While moving the source along the axis of rotation of the GC-PET system, a tomographic acquisition takes place. The scan covers the full axial field of view of the 2-D or 3-D scatter frame. Depending on the acquisition software, point source scanning takes place continuously while only one projection is acquired or is done in step-and-shoot mode with the number of positions equal to the number of gantry steps. Special software was developed to analyse the resulting list mode acquisition files and to produce an image of the recorded coincidence events of each head. Results: Uniformity images of coincidence events were obtained after further correction for systematic sensitivity variations caused by acquisition geometry. The resulting images are analysed visually and by calculating NEMA uniformity indices as for a planar flood field. The method has been applied successfully to two different brands of GC-PET capable gamma cameras. Conclusion: Uniformity of GC-PET can be tested quickly and accurately with a routine QC procedure, using a Sodium-22 scanning point source and an inexpensive mechanical scanning device. The method can be used for both 2-D and 3-D acquisition modes and fills an important gap in the quality control system for GC-PET

Light Stable Isotopic Compositions of Enriched Mantle Sources: Resolving the Dehydration Paradox

Science.gov (United States)

Dixon, J. E.; Bindeman, I. N.; Kingsley, R. H.

2017-12-01

An outstanding puzzle in mantle geochemistry has been the origin and evolution of Earth's volatile components. The "dehydration paradox" refers to the following conundrum. Mantle compositions for some enriched mid-ocean ridge (MORB) and ocean island (OIB) basalts basalts require involvement of a mostly dehydrated slab component to explain the trace element ratios and radiogenic isotopic compositions, but a fully hydrated slab component to explain the stable isotopic compositions. Volatile and stable isotopic data on enriched MORB show a diversity of enriched components. Pacific PREMA-type basalts (H2O/Ce = 215 ± 30, δDSMOW = -45 ± 5 ‰) are similar to those in the north Atlantic (H2O/Ce = 220 ± 30; δDSMOW = -30 to -40 ‰). Basalts with EM-type signatures have regionally variable volatile compositions. North Atlantic EM-type basalts are wetter (H2O/Ce = 330 ± 30) and have isotopically heavier hydrogen (δDSMOW = -57 ± 5 ‰) than north Atlantic MORB. South Atlantic EM-type basalts are damp (H2O/Ce = 120 ± 10) with intermediate δDSMOW (-68 ± 2 ‰), similar to dDSMOW for Pacific MORB. North EPR EM-type basalts are dry (H2O/Ce = 110 ± 20) and isotopically light (δDSMOW = -94 ± 3 ‰). Boron and lithium isotopic ratios parallel the trends observed for dDSMOW. A multi-stage metasomatic and melting model accounts for the origin of the enriched components by extending the subduction factory concept down through the mantle transition zone, with slab temperature a key variable. The dehydration paradox is resolved by decoupling of volatiles from lithophile elements, reflecting primary dehydration of the slab followed by secondary rehydration and re-equilibration by fluids derived from subcrustal hydrous phases (e.g., antigorite) in cooler, deeper parts of the slab. The "expanded subduction factory" model includes melting at several key depths, including 1) 180 to 280 km, where EM-type mantle compositions are generated above slabs with average to hot thermal

Source apportionment analysis of air pollutants using CMAQ/BFM for national air quality management policy over Republic of Korea.

Science.gov (United States)

Moon, N.; Kim, S.; Seo, J.; Lee, Y. J.

2017-12-01

Recently, the Korean government is focusing on solving air pollution problem such as fine particulate matter and ozone. Korea has high population density and concentrated industrial complex in its limited land space. For better air quality management, it is important to understand source and contribution relation to target pollutant. The air quality analysis representing the mutual contribution among the local regions enables to understand the substantive state of the air quality of a region in association with neighboring regions. Under this background, the source apportionment of PM10, PM2.5, O3, NO2, SO2 using WRF and CMAQ/BFM was analyzed over Korea and BFM was applied to mobile, area and point sources in each local government. The contribution rate from neighboring region showed different pattern for each pollutant. In case of primary pollutants such as NO2, SO2, local source contribution is dominant, on the other hand secondary pollutants case especially O3, contribution from neighboring region is higher than that from source region itself. Local source contribution to PM10 showed 20-25% and the contribution rate to O3 has big difference with different meteorological condition year after year. From this study, we tried to estimate the conversion rate between source (NOx, VOC, SO2, NH3, PMC, PM2.5, CO) and concentration (PM10, PM2.5, O3, NO2, SO2,) by regional group over Korea. The result can contribute to the decision-making process of important national planning related to large-scale industrial developments and energy supply policies (eg., operations of coal-fired power plants and diesel cars) and emission control plan, where many controversies and concerns are currently concentrated among local governments in Korea. With this kind of approach, various environmental and social problems related to air quality can also be identified early so that a sustainable and environmentally sound plan can be established by providing data infrastructures to be utilized

Factors Affecting Source-Water Quality after Disturbance of Forests by Wildfire

Science.gov (United States)

Murphy, S. F.; Martin, D. A.; McCleskey, R. B.; Writer, J. H.

2015-12-01

Forests yield high-quality water supplies to communities throughout the world, in part because forest cover reduces flooding and the consequent transport of suspended and dissolved constituents to surface water. Disturbance by wildfire reduces or eliminates forest cover, leaving watersheds susceptible to increased surface runoff during storms and reduced ability to retain contaminants. We assessed water-quality response to hydrologic events for three years after a wildfire in the Fourmile Creek Watershed, near Boulder, Colorado, and found that hydrologic and geochemical responses downstream of a burned area were primarily driven by small, brief convective storms that had relatively high, but not unusual, rainfall intensity. Total suspended sediment, dissolved organic carbon, nitrate, and manganese concentrations were 10-156 times higher downstream of a burned area compared to upstream, and water quality was sufficiently impaired to pose water-treatment concerns. The response in both concentration and yield of water-quality constituents differed depending on source availability and dominant watershed processes controlling the constituent. For example, while all constituent concentrations were highest during storm events, annual sediment yields downstream of the burned area were controlled by storm events and subsequent mobilization, whereas dissolved organic carbon yields were more dependent on spring runoff from upstream areas. The watershed response was affected by a legacy of historical disturbance: the watershed had been recovering from extensive disturbance by mining, railroad and road development, logging, and fires in the late 19th and early 20th centuries, and we observed extensive erosion of mine waste in response to these summer storms. Therefore, both storm characteristics and historical disturbance in a burned watershed must be considered when evaluating the role of wildfire on water quality.

Looking Upstream: Findings from Focus Groups on Public Perceptions of Source Water Quality in British Columbia, Canada.

Directory of Open Access Journals (Sweden)

Natalie Henrich

Full Text Available In association with the development of new microbial tests for source water quality (SWQ, focus groups with members of the public were conducted to gain insight into their perceptions of SWQ, behaviours and contaminants they think pose the greatest threat to its quality, and what/how they want to know about SWQ. Discussions revealed a low concern about SWQ in general, and in particular about microbial contamination. Participants identified behaviours that threaten SWQ, barriers to changing behaviour and suggestions for inducing change. A strong desire was expressed for water quality information to be interpreted and communicated in terms of how SWQ may impact human health and how their actions should be altered in response to test results. The information can be used to inform communication strategies and possibly impact policies associated with water quality testing and implementation of new tests. More broadly, awareness of the public's understanding and beliefs about source water can be used in working with the public to adopt water-friendly behaviours, influence the content and methods of communicating with the public about water issues and water quality, and could contribute to the direction of future research and investment into water technologies to align with the public's priorities.

Effects of irradiation source and dose level on quality characteristics of processed meat products

Science.gov (United States)

Ham, Youn-Kyung; Kim, Hyun-Wook; Hwang, Ko-Eun; Song, Dong-Heon; Kim, Yong-Jae; Choi, Yun-Sang; Song, Beom-Seok; Park, Jong-Heum; Kim, Cheon-Jei

2017-01-01

The effect of irradiation source (gamma-ray, electron-beam, and X-ray) and dose levels on the physicochemical, organoleptic and microbial properties of cooked beef patties and pork sausages was studied, during 10 days of storage at 30±1 °C. The processed meat products were irradiated at 0, 2.5, 5, 7.5, and 10 kGy by three different irradiation sources. The pH of cooked beef patties and pork sausages was unaffected by irradiation sources or their doses. The redness of beef patties linearly decreased with increasing dose level (Pchanges in overall acceptability were observed for pork sausages regardless of irradiation source (P>0.05), while gamma-ray irradiated beef patties showed significantly decreased overall acceptability in a dose-dependent manner (Poxidation of samples was accelerated by irradiation depending on irradiation sources and dose levels during storage at 30 °C. E-beam reduced total aerobic bacteria of beef patties more effectively, while gamma-ray considerably decreased microbes in pork sausages as irradiation dose increased. The results of this study indicate that quality attributes of meat products, in particular color, lipid oxidation, and microbial properties are significantly influenced by the irradiation sources.

Assessment of Metabolome Annotation Quality: A Method for Evaluating the False Discovery Rate of Elemental Composition Searches

Science.gov (United States)

Matsuda, Fumio; Shinbo, Yoko; Oikawa, Akira; Hirai, Masami Yokota; Fiehn, Oliver; Kanaya, Shigehiko; Saito, Kazuki

2009-01-01

Background In metabolomics researches using mass spectrometry (MS), systematic searching of high-resolution mass data against compound databases is often the first step of metabolite annotation to determine elemental compositions possessing similar theoretical mass numbers. However, incorrect hits derived from errors in mass analyses will be included in the results of elemental composition searches. To assess the quality of peak annotation information, a novel methodology for false discovery rates (FDR) evaluation is presented in this study. Based on the FDR analyses, several aspects of an elemental composition search, including setting a threshold, estimating FDR, and the types of elemental composition databases most reliable for searching are discussed. Methodology/Principal Findings The FDR can be determined from one measured value (i.e., the hit rate for search queries) and four parameters determined by Monte Carlo simulation. The results indicate that relatively high FDR values (30–50%) were obtained when searching time-of-flight (TOF)/MS data using the KNApSAcK and KEGG databases. In addition, searches against large all-in-one databases (e.g., PubChem) always produced unacceptable results (FDR >70%). The estimated FDRs suggest that the quality of search results can be improved not only by performing more accurate mass analysis but also by modifying the properties of the compound database. A theoretical analysis indicates that FDR could be improved by using compound database with smaller but higher completeness entries. Conclusions/Significance High accuracy mass analysis, such as Fourier transform (FT)-MS, is needed for reliable annotation (FDR metabolome data. PMID:19847304

E-Services quality assessment framework for collaborative networks

Science.gov (United States)

Stegaru, Georgiana; Danila, Cristian; Sacala, Ioan Stefan; Moisescu, Mihnea; Mihai Stanescu, Aurelian

2015-08-01

In a globalised networked economy, collaborative networks (CNs) are formed to take advantage of new business opportunities. Collaboration involves shared resources and capabilities, such as e-Services that can be dynamically composed to automate CN participants' business processes. Quality is essential for the success of business process automation. Current approaches mostly focus on quality of service (QoS)-based service selection and ranking algorithms, overlooking the process of service composition which requires interoperable, adaptable and secure e-Services to ensure seamless collaboration, data confidentiality and integrity. Lack of assessment of these quality attributes can result in e-Service composition failure. The quality of e-Service composition relies on the quality of each e-Service and on the quality of the composition process. Therefore, there is the need for a framework that addresses quality from both views: product and process. We propose a quality of e-Service composition (QoESC) framework for quality assessment of e-Service composition for CNs which comprises of a quality model for e-Service evaluation and guidelines for quality of e-Service composition process. We implemented a prototype considering a simplified telemedicine use case which involves a CN in e-Healthcare domain. To validate the proposed quality-driven framework, we analysed service composition reliability with and without using the proposed framework.

Quality and Chemical Composition of Organic and Non-Organic Vetiver Oil

Directory of Open Access Journals (Sweden)

Asep Kadarohman

2014-03-01

Full Text Available Vetiver oil (Vetiveria zizanoides has been used as perfume materials, cosmetics, fragrance soaps, anti-inflammation, repellent, and insecticidal agents. Organic vetiver oil has higher economical value than non-organic vetiver oil and it has been regarded to be able to compete in the global market. Therefore, studies have been carried out using 1 hectare of land and the first generation of organic vetiver oil has produced 0.57% of yield, greater than non-organic (0.50%. The quality of organic and non-organic vetiver oil was analyzed by Indonesian Standard (SNI parameter, pesticide residue test, chemical composition by GC/MS, and the appearance of vetiver root. In general, the result of organic and non-organic vetiver oil has fulfilled the national standard; the quality of organic vetiver oil was better than non-organic one. Physically, the appearance of organic vetiver root was better than non-organic vetiver root; organic vetiver root was denser, more appealing, and did not have any black spots. The pesticide residue of organic vetiver oil was lower than non-organic vetiver oil. Based on SNI test, vetiverol (oxygen compounds in organic vetiver oil was higher than non-organic vetiver oil.

The effects of feed composition on the sensory quality of organic rainbow trout during ice storage

DEFF Research Database (Denmark)

Green-Pedersen, Ditte; Hyldig, Grethe; Jacobsen, Charlotte

fishmeal and a mixture of protein from organic vegetable, while the lipid sources were fish oil and organic oil from linseed, sunflower, rapeseed and grape seed. Sensory analysis was performed after 3, 5, 7 and 14 days of storage in ice. The results showed that both protein and lipid source in the feed can...... after 14 days of storage, indicating that vegetable protein in the feed increases the self-life of organic rainbow trout.......The focus of this work was to study which effects the type of protein and lipid source in the feed for organic Rainbow trout influences had on the sensory quality of final product. Two and four different protein and lipid sources were used in the experiment respectively. The protein sources were...

Microbial quality of improved drinking water sources: evidence from western Kenya and southern Vietnam.

Science.gov (United States)

Grady, Caitlin A; Kipkorir, Emmanuel C; Nguyen, Kien; Blatchley, E R

2015-06-01

In recent decades, more than 2 billion people have gained access to improved drinking water sources thanks to extensive effort from governments, and public and private sector entities. Despite this progress, many water sector development interventions do not provide access to safe water or fail to be sustained for long-term use. The authors examined drinking water quality of previously implemented water improvement projects in three communities in western Kenya and three communities in southern Vietnam. The cross-sectional study of 219 households included measurements of viable Escherichia coli. High rates of E. coli prevalence in these improved water sources were found in many of the samples. These findings suggest that measures above and beyond the traditional 'improved source' definition may be necessary to ensure truly safe water throughout these regions.

Effect of source and level of potash on yield and quality of potato tubers

International Nuclear Information System (INIS)

Khan, M.Z.; Akhtar, M.E.; Mahmood, M.M.

2010-01-01

Field experiments were conducted for two consecutive seasons at NARC potato research area Islamabad, Pakistan, to study comparative effect of source, levels and methods of K fertilization on yield and quality of potato produce. Nitrogen and phosphorus were applied at 250 and 125 kg ha/sup -1/, respectively whereas three K/sub 2/O levels, 0, 150 and 225 kg ha/sup -1/ from two sources of potash (SOP and MOP) were tested. Potassium was also applied as foliar spray at 1% K/sub 2/O solution at 30, 45 and 60 days after germination (DAG) and soil was also amended by 150 kg K/sub 2/O ha/sup -1/. A significant increase in tuber yield with K application at 150 kg ha/sup -1/ as K/sub 2/O from both the K sources over NP treatment was recorded. Increase in tuber yield with K/sub 2/O at the rate of 225 kg ha/sup -1/ was statistically nonsignificant compared to 150 kg K/sub 2/O ha/sup -1/. A positive interaction between soil applied P and K with N in plant system was observed. Potassium treatments not only increased K concentration but also affected N and P contents in potato tubers. The quality parameters like dry matter, specific gravity, starch contents, vitamin-C and ash contents were also affected with P and K fertilization. (author)

Tracing chlorine sources of thermal and mineral springs along and across the Cascade Range using halogen and chlorine isotope compositions

Science.gov (United States)

Cullen, Jeffrey T.; Barnes, Jaime D.; Hurwitz, Shaul; Leeman, William P.

2015-01-01

In order to provide constraints on the sources of chlorine in spring waters associated with arc volcanism, the major/minor element concentrations and stable isotope compositions of chlorine, oxygen, and hydrogen were measured in 28 thermal and mineral springs along the Cascade Range in northwestern USA. Chloride concentrations in the springs range from 64 to 19,000 mg/L and View the MathML source values range from +0.2‰ to +1.9‰ (average=+1.0±0.4‰), with no systematic variation along or across the arc, nor correlations with their presumed underlying basement lithologies. Additionally, nine geochemically well-characterized lavas from across the Mt. St. Helens/Mt. Adams region of the Cascade Range (Leeman et al., 2004 and Leeman et al., 2005) were analyzed for their halogen concentrations and Cl isotope compositions. In the arc lavas, Cl and Br concentrations from the volcanic front are higher than in lavas from the forearc and backarc. F and I concentrations progressively decrease from forearc to backarc, similar to the trend documented for B in most arcs. View the MathML source values of the lavas range from −0.1 to +0.8‰ (average = +0.4±0.3‰). Our results suggest that the predominantly positive View the MathML source values observed in the springs are consistent with water interaction with underlying 37Cl-enriched basalt and/or altered oceanic crust, thereby making thermal spring waters a reasonable proxy for the Cl isotope compositions of associated volcanic rocks in the Cascades. However, waters with View the MathML source values >+1.0‰ also suggest additional contributions of chlorine degassed from cooling magmas due to subsurface vapor–liquid HCl fractionation in which Cl is lost to the aqueous fluid phase and 37Cl is concentrated in the ascending magmatic HCl vapor. Future work is necessary to better constrain Cl isotope behavior during volcanic degassing and fluid–rock interaction in order to improve volatile flux estimates through

Microbial and metal water quality in rain catchments compared with traditional drinking water sources in the East Sepik Province, Papua New Guinea.

Science.gov (United States)

Horak, Helena M; Chynoweth, Joshua S; Myers, Ward P; Davis, Jennifer; Fendorf, Scott; Boehm, Alexandria B

2010-03-01

In Papua New Guinea, a significant portion of morbidity and mortality is attributed to water-borne diseases. To reduce incidence of disease, communities and non-governmental organizations have installed rain catchments to provide drinking water of improved quality. However, little work has been done to determine whether these rain catchments provide drinking water of better quality than traditional drinking water sources, and if morbidity is decreased in villages with rain catchments. The specific aim of this study was to evaluate the quality of water produced by rain catchments in comparison with traditional drinking water sources in rural villages in the East Sepik Province. Fifty-four water sources in 22 villages were evaluated for enterococci and Escherichia coli densities as well as 14 health-relevant metals. In addition, we examined how the prevalence of diarrhoeal illness in villages relates to the type of primary drinking water source. The majority of tested metals were below World Health Organization safety limits. Catchment water sources had lower enterococci and E. coli than other water sources. Individuals in villages using Sepik River water as their primary water source had significantly higher incidence of diarrhoea than those primarily using other water sources (streams, dug wells and catchments).

Indoor air quality in Portuguese schools: levels and sources of pollutants.

Science.gov (United States)

Madureira, J; Paciência, I; Pereira, C; Teixeira, J P; Fernandes, E de O

2016-08-01

Indoor air quality (IAQ) parameters in 73 primary classrooms in Porto were examined for the purpose of assessing levels of volatile organic compounds (VOCs), aldehydes, particulate matter, ventilation rates and bioaerosols within and between schools, and potential sources. Levels of VOCs, aldehydes, PM2.5 , PM10 , bacteria and fungi, carbon dioxide (CO2 ), carbon monoxide, temperature and relative humidity were measured indoors and outdoors and a walkthrough survey was performed concurrently. Ventilation rates were derived from CO2 and occupancy data. Concentrations of CO2 exceeding 1000 ppm were often encountered, indicating poor ventilation. Most VOCs had low concentrations (median of individual species <5 μg/m(3) ) and were below the respective WHO guidelines. Concentrations of particulate matter and culturable bacteria were frequently higher than guidelines/reference values. The variability of VOCs, aldehydes, bioaerosol concentrations, and CO2 levels between schools exceeded the variability within schools. These findings indicate that IAQ problems may persist in classrooms where pollutant sources exist and classrooms are poorly ventilated; source control strategies (related to building location, occupant behavior, maintenance/cleaning activities) are deemed to be the most reliable for the prevention of adverse health consequences in children in schools. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Light influence in the nutritional composition of Brassica oleracea sprouts.

Science.gov (United States)

Vale, A P; Santos, J; Brito, N V; Peixoto, V; Carvalho, Rosa; Rosa, E; Oliveira, M Beatriz P P

2015-07-01

Brassica sprouts are considered a healthy food product, whose nutritional quality can be influenced by several factors. The aim of this work was to monitor the nutritional composition changes promoted by different sprouting conditions of four varieties of Brassica oleracea (red cabbage, broccoli, Galega kale and Penca cabbage). Sprouts were grown under light/darkness cycles and complete darkness. Standard AOAC methods were applied for nutritional value evaluation, while chromatographic methods with UV-VIS and FID detection were used to determine the free amino acids and fatty acids, respectively. Mineral content was analyzed by atomic absorption spectrometry. Sprouts composition revealed them as an excellent source of protein and dietary fiber. Selenium content was one of the most distinctive feature of sprouts, being the sprouting conditions determinant for the free amino acid and fatty acids profile. The use of complete darkness was beneficial to the overall nutritional quality of the brassica sprouts studied. Copyright © 2015 Elsevier Ltd. All rights reserved.

Source identification of fine-grained suspended sediment in the Kharaa River basin, northern Mongolia

Energy Technology Data Exchange (ETDEWEB)

Theuring, Philipp [Department of Aquatic Ecosystem Analysis and Management — ASAM, Helmholtz Centre for Environmental Research — UFZ, Brückstrasse 3a, D-39114 Magdeburg (Germany); Collins, Adrian L. [Sustainable Soils and Grassland Systems Department, Rothamsted Research, North Wyke, Okehampton, Devon EX20 2SB (United Kingdom); Rode, Michael [Department of Aquatic Ecosystem Analysis and Management — ASAM, Helmholtz Centre for Environmental Research — UFZ, Brückstrasse 3a, D-39114 Magdeburg (Germany)

2015-09-01

Fine sediment inputs into river systems can be a major source of nutrients and heavy metals and have a strong impact on water quality and ecosystem functions of rivers and lakes, including those in semiarid regions. However, little is known to date about the spatial distribution of sediment sources in most large scale river basins in Central Asia. Accordingly, a sediment source fingerprinting technique was used to assess the spatial sources of fine-grained (< 10 μm) sediment in the 15 000 km{sup 2} Kharaa River basin in northern Mongolia. Variation in geochemical composition (e.g. in Ti, Sn, Mo, Mn, As, Sr, B, U, Ca and Sb) was used for sediment source discrimination with geochemical composite fingerprints based on Genetic Algorithm (GA)-driven Discriminant Function Analysis, the Kruskal–Wallis H-test and Principal Component Analysis. All composite fingerprints yielded a satisfactory GOF (> 0.97) and were subsequently used for numerical mass balance modelling with uncertainty analysis. The contributions of the individual sub-catchment spatial sediment sources varied from 6.4% (the headwater sub-catchment of Sugnugur Gol) to 36.2% (the Kharaa II sub-catchment in the middle reaches of the study basin), generally showing higher contributions from the sub-catchments in the middle, rather than the upstream, portions of the study area. The importance of river bank erosion is shown to increase from upstream to midstream tributaries. The source tracing procedure provides results in reasonable accordance with previous findings in the study region and demonstrates the applicability and associated uncertainties of the approach for fine-grained sediment source investigation in large scale semi-arid catchments. - Highlights: • Applied statistical approach for selecting composite fingerprints in Mongolia. • Geochemical fingerprinting for the definition of source areas in semiarid catchment. • Test of applicability of sediment sourcing in large scale semi-arid catchments

Energy based source location by using acoustic emission for damage detection in steel and composite CNG tank

Energy Technology Data Exchange (ETDEWEB)

Kim, Il Sik; Han, Byeong Hee; Park, Choon Su; Yoon, Dong Jin [Center for Safety Measurements, Korea Research Institute of Standards and Science, Daejeon (Korea, Republic of)

2015-10-15

Acoustic emission (AE) is an effective nondestructive test that uses transient elastic wave generated by the rapid release of energy within a material to detect any further growth or expansion of existing defects. Over the past decades, because of environmental issues, the use of compressed natural gas (CNG) as an alternative fuel for vehicles is increasing because of environmental issues. For this reason, the importance and necessity of detecting defects on a CNG fuel tank has also come to the fore. The conventional AE method used for source location is highly affected by the wave speed on the structure, and this creates problems in inspecting a composite CNG fuel tank. Because the speed and dispersion characteristics of the wave are different according to direction of structure and laminated layers. In this study, both the conventional AE method and the energy based contour map method were used for source location. This new method based on pre-acquired D/B was used for overcoming the limitation of damage localization in a composite CNG fuel tank specimen which consists of a steel liner cylinder overwrapped by GFRP. From the experimental results, it is observed that the damage localization is determined with a small error at all tested points by using the energy based contour map method, while there were a number of mis-locations or large errors at many tested points by using the conventional AE method. Therefore, the energy based contour map method used in this work is more suitable technology for inspecting composite structures.

Effects of gestational maternal undernutrition on growth, carcass composition and meat quality of rabbit offspring.

Directory of Open Access Journals (Sweden)

George K Symeon

Full Text Available An experiment was conducted in order to evaluate the effects of gestational undernutrition of rabbit does on growth, carcass composition and meat quality of the offsprings. Thirty primiparous non lactating rabbit does were artificially inseminated and randomly divided in three treatment groups: Control (C; fed to 100% of maintenance requirements throughout gestation, n = 10, early undernourished (EU; fed to 50% of maintenance requirements during days 7-19 of gestation, n = 10 and late undernourished (LU; fed to 50% of maintenance requirements during days 20-27 of gestation, n = 10. During the 4th week of the gestation period, LU does significantly lost weight compared to C and EU groups (P<0.05. At kindling, C does produced litters with higher proportions of stillborn kits (P<0.05 while the total litter size (alive and stillborn kits was not different among groups (10.7, 12.8 and 12.7 kits in C, EU and LU groups, respectively. Kit birth weight tended to be lower in the LU group. During fattening, body weight and feed intake were not different among offsprings of the three experimental groups. Moreover, the maternal undernutrition did not have any impact on carcass composition of the offsprings in terms of carcass parts and internal organs weights as well as meat quality of L. lumborum muscle (pH24, colour, water holding capacity and shear values at slaughter (70 days of age. Therefore, it can be concluded that the gestational undernutrition of the mother does not have detrimental effects on the productive and quality traits of the offsprings.

Hanford Site Composite Analysis Technical Approach Description: Automated Quality Assurance Process Design.

Energy Technology Data Exchange (ETDEWEB)

Dockter, Randy E. [CH2M HILL Plateau Remediation Company, Richland, WA (United States)

2017-07-31

The U.S. Department of Energy (DOE) in DOE O 435.1 Chg. 1, Radioactive Waste Management, requires the preparation and maintenance of a composite analysis (CA). The primary purpose of the CA is to provide a reasonable expectation that the primary public dose limit is not likely to be exceeded by multiple source terms that may significantly interact with plumes originating at a low-level waste disposal facility. The CA is used to facilitate planning and land use decisions that help assure disposal facility authorization will not result in long-term compliance problems; or, to determine management alternatives, corrective actions, or assessment needs if potential problems are identified.

Detection of Noise in Composite Step Signal Pattern by Visualizing Signal Waveforms

Directory of Open Access Journals (Sweden)

Chaman Verma

2018-03-01

Full Text Available The Step Composite Signals is the combination of vital informative signals that are compressed and coded to produce a predefined test image on a display device. It carries the desired sequence of information from source to destination. This information may be transmitted as digital signal, video information or data signal required as an input for the destination module. For testing of display panels, Composite Test Signals are the most important attribute of test signal transmission system. In the current research paper we present an approach for the noise detection in Composite Step Signal by analysing Composite Step Signal waveforms. The analysis of the signal waveforms reveals that the noise affected components of the signal and subsequently noise reduction process is initiated which targets noisy signal component only. Thus the quality of signal is not compromised during noise reduction process.

Modelling the molecular composition and nuclear-spin chemistry of collapsing prestellar sources

Science.gov (United States)

Hily-Blant, P.; Faure, A.; Rist, C.; Pineau des Forêts, G.; Flower, D. R.

2018-04-01

We study the gravitational collapse of prestellar sources and the associated evolution of their chemical composition. We use the University of Grenoble Alpes Astrochemical Network (UGAN), which includes reactions involving the different nuclear-spin states of H2, H+3, and of the hydrides of carbon, nitrogen, oxygen, and sulfur, for reactions involving up to seven protons. In addition, species-to-species rate coefficients are provided for the ortho/para interconversion of the H_3^+ + H2 system and isotopic variants. The composition of the medium is followed from an initial steady state through the early phase of isothermal gravitational collapse. Both the freeze-out of the molecules on to grains and the coagulation of the grains were incorporated in the model. The predicted abundances and column densities of the spin isomers of ammonia and its deuterated forms are compared with those measured recently towards the prestellar cores H-MM1, L16293E, and Barnard B1. We find that gas-phase processes alone account satisfactorily for the observations, without recourse to grain-surface reactions. In particular, our model reproduces both the isotopologue abundance ratios and the ortho:para ratios of NH2D and NHD2 within observational uncertainties. More accurate observations are necessary to distinguish between full scrambling processes—as assumed in our gas-phase network—and direct nucleus- or atom-exchange reactions.

Quality protein maize (QPM) seeds grown in Côte d'Ivoire: A source ...

African Journals Online (AJOL)

Quality protein maize (QPM) seeds grown in Côte d'Ivoire: A source of high value edible oil. ... Biochemical and nutritive analysis have revealed the following assets: unsaponifiable matter (1.43 ± 0.21 and 1.70 ± 0.10%), phosphorus (0.10 ± 0.02 mg/g), carotenoids (0.86 ± 0.01 and 1.06 ± 0.01 mg/g), vitamin A (0.45 ± 0.01 ...

Development of sustainable water treatment technology using scientifically based calculated indexes of source water quality indicators

Directory of Open Access Journals (Sweden)

А. С. Трякина

2017-10-01

Full Text Available The article describes selection process of sustainable technological process flow chart for water treatment procedure developed on scientifically based calculated indexes of quality indicators for water supplied to water treatment facilities. In accordance with the previously calculated values of the indicators of the source water quality, the main purification facilities are selected. A more sustainable flow chart for the modern water quality of the Seversky Donets-Donbass channel is a two-stage filtering with contact prefilters and high-rate filters. The article proposes a set of measures to reduce such an indicator of water quality as permanganate oxidation. The most suitable for these purposes is sorption purification using granular activated carbon for water filtering. The increased water hardness is also quite topical. The method of ion exchange on sodium cation filters was chosen to reduce the water hardness. We also evaluated the reagents for decontamination of water. As a result, sodium hypochlorite is selected for treatment of water, which has several advantages over chlorine and retains the necessary aftereffect, unlike ozone. A technological flow chart with two-stage purification on contact prefilters and two-layer high-rate filters (granular activated carbon - quartz sand with disinfection of sodium hypochlorite and softening of a part of water on sodium-cation exchangers filters is proposed. This technological flow chart of purification with any fluctuations in the quality of the source water is able to provide purified water that meets the requirements of the current sanitary-hygienic standards. In accordance with the developed flow chart, guidelines and activities for the reconstruction of the existing Makeevka Filtering Station were identified. The recommended flow chart uses more compact and less costly facilities, as well as additional measures to reduce those water quality indicators, the values of which previously were in

Identification of quantitative trait loci for carcass composition and meat quality traits in a commercial finishing cross

NARCIS (Netherlands)

Wijk, van H.J.; Dibbits, B.W.; Baron, E.E.; Brings, A.D.; Harlizius, B.; Groenen, M.A.M.; Knol, E.F.; Bovenhuis, H.

2006-01-01

A QTL study for carcass composition and meat quality traits was conducted on finisher pigs of a cross between a synthetic Pie¿train/Large White boar line and a commercial sow cross. The mapping population comprised 715 individuals evaluated for a total of 30 traits related to growth and fatness (4

Using high frequency CDOM hyperspectral absorption to fingerprint river water sources

Science.gov (United States)

Beckler, J. S.; Kirkpatrick, G. J.; Dixon, L. K.; Milbrandt, E. C.

2016-12-01

Quantifying riverine carbon transfer from land to sea is complicated by variability in dissolved organic carbon (DOC), closely-related dissolved organic matter (DOM) and chromophoric dissolved organic matter (CDOM) concentrations, as well as in the composition of the freshwater end members of multiple drainage basins and seasons. Discrete measurements in estuaries have difficulty resolving convoluted upstream watershed dynamics. Optical measurements, however, can provide more continuous data regarding the molecular composition and concentration of the CDOM as it relates to river flow, tidal mixing, and salinity and may be used to fingerprint source waters. For the first time, long-term, hyperspectral CDOM measurements were obtained on filtered Caloosahatchee River estuarine waters using an in situ, long-pathlength spectrophotometric instrument, the Optical Phytoplankton Discriminator (OPD). Through a collaborative monitoring effort among partners within the Gulf of Mexico Coastal Ocean Observing System (GCOOS), ancillary measurements of fluorescent DOM (FDOM) and water quality parameters were also obtained from co-located instrumentation at high frequency. Optical properties demonstrated both short-term (hourly) tidal variations and long-term (daily - weekly) variations corresponding to changes in riverine flow and salinity. The optical properties of the river waters are demonstrated to be a dilution-adjusted linear combination of the optical properties of the source waters comprising the overall composition (e.g. Lake Okeechobee, watershed drainage basins, Gulf of Mexico). Overall, these techniques are promising as a tool to more accurately constrain the carbon flux to the ocean and to predict the optical quality of coastal waters.

Dual-source computed tomography in patients with acute chest pain: feasibility and image quality

Energy Technology Data Exchange (ETDEWEB)

Schertler, Thomas; Scheffel, Hans; Frauenfelder, Thomas; Desbiolles, Lotus; Leschka, Sebastian; Stolzmann, Paul; Marincek, Borut; Alkadhi, Hatem [University Hospital Zurich, Department of Medical Radiology, Institute of Diagnostic Radiology, Zurich (Switzerland); Seifert, Burkhardt [University of Zurich, Department of Biostatistics, Zurich (Switzerland); Flohr, Thomas G. [Computed Tomography CTE PA, Siemens Medical Solutions, Forchheim (Germany)

2007-12-15

The aim of this study was to determine the feasibility and image quality of dual-source computed tomography angiography (DSCTA) in patients with acute chest pain for the assessment of the lung, thoracic aorta, and for pulmonary and coronary arteries. Sixty consecutive patients (32 female, 28 male, mean age 58.1{+-}16.3 years) with acute chest pain underwent contrast-enhanced electrocardiography-gated DSCTA without prior beta-blocker administration. Vessel attenuation of different thoracic vascular territories was measured, and image quality was semi-quantitatively analyzed by two independent readers. Image quality of the thoracic aorta was diagnostic in all 60 patients, image quality of pulmonary arteries was diagnostic in 59, and image quality of coronary arteries was diagnostic in 58 patients. Pairwise intraindividual comparisons of attenuation values were small and ranged between 1{+-}6 HU comparing right and left coronary artery and 56{+-}9 HU comparing the pulmonary trunk and left ventricle. Mean attenuation was 291{+-}65 HU in the ascending aorta, 334{+-}93 HU in the pulmonary trunk, and 285{+-}66 HU and 268{+-}67 HU in the right and left coronary artery, respectively. DSCTA is feasible and provides diagnostic image quality of the thoracic aorta, pulmonary and coronary arteries in patients with acute chest pain. (orig.)

Dual-source computed tomography in patients with acute chest pain: feasibility and image quality

International Nuclear Information System (INIS)

Schertler, Thomas; Scheffel, Hans; Frauenfelder, Thomas; Desbiolles, Lotus; Leschka, Sebastian; Stolzmann, Paul; Marincek, Borut; Alkadhi, Hatem; Seifert, Burkhardt; Flohr, Thomas G.

2007-01-01

The aim of this study was to determine the feasibility and image quality of dual-source computed tomography angiography (DSCTA) in patients with acute chest pain for the assessment of the lung, thoracic aorta, and for pulmonary and coronary arteries. Sixty consecutive patients (32 female, 28 male, mean age 58.1±16.3 years) with acute chest pain underwent contrast-enhanced electrocardiography-gated DSCTA without prior beta-blocker administration. Vessel attenuation of different thoracic vascular territories was measured, and image quality was semi-quantitatively analyzed by two independent readers. Image quality of the thoracic aorta was diagnostic in all 60 patients, image quality of pulmonary arteries was diagnostic in 59, and image quality of coronary arteries was diagnostic in 58 patients. Pairwise intraindividual comparisons of attenuation values were small and ranged between 1±6 HU comparing right and left coronary artery and 56±9 HU comparing the pulmonary trunk and left ventricle. Mean attenuation was 291±65 HU in the ascending aorta, 334±93 HU in the pulmonary trunk, and 285±66 HU and 268±67 HU in the right and left coronary artery, respectively. DSCTA is feasible and provides diagnostic image quality of the thoracic aorta, pulmonary and coronary arteries in patients with acute chest pain. (orig.)

Air Quality Monitoring with Routine Utilization of Ion Beam Analysis

International Nuclear Information System (INIS)

Wegrzynek, D.

2013-01-01

Full text: Information on source contributions to ambient air particulate concentrations is a vital tool for air quality management. Traditional gravimetric analysis of airborne particulate matter is unable to provide information on the sources contributing to air particulate concentrations. Ion beam analysis is used to identify the elemental composition of air particulates for source apportionment and determining the relative contribution of biogenic and anthropogenic sources to air particulate pollution. The elemental composition is obtained by proton induced X-ray emission technique (PIXE), which is an ion beam analysis (IBA) technique. The element concentrations are deduced from the X ray spectra produced when the particulate collected on a filter is bombarded with a high-energy proton beam. As part of the UNDP/IAEA/RCA Project RAS/8/082 ‘Better Management of the Environment, Natural Resources and Industrial Growth through Isotope and Radiation Technology,’ a collaborative alliance was formed between the Institute of Geological and Nuclear Sciences Limited and the Wellington Regional Council, New Zeland [1]. The purpose of the project was to examine the elemental composition of air particulate matter and determine the origins through source apportionment techniques. In New Zealand PM 10 and PM 2.5 fractions have been collected at the industrial area of Seaview, Wellington over two years using a GENT stacked filter unit sampler. Concentrations of elements with atomic mass above neon were determined using ion beam analysis and elemental carbon concentrations were determined using a reflectometer. Specific ambient source elemental 'fingerprints' were then determined by factor analysis and the relative contributions of various local and regional sources were assessed. The significant factors (sources) were determined to be sea salt, soil, industry, and combustion sources. Local industry was found to contribute to ambient lead concentrations. (author)

Seasonal variability of PM2.5 composition and sources in the Klang Valley urban-industrial environment

Directory of Open Access Journals (Sweden)

N. Amil

2016-04-01

Full Text Available This study investigates the fine particulate matter (PM2.5 variability in the Klang Valley urban-industrial environment. In total, 94 daily PM2.5 samples were collected during a 1-year campaign from August 2011 to July 2012. This is the first paper on PM2.5 mass, chemical composition and sources in the tropical environment of Southeast Asia, covering all four seasons (distinguished by the wind flow patterns including haze events. The samples were analysed for various inorganic components and black carbon (BC. The chemical compositions were statistically analysed and the temporal aerosol pattern (seasonal was characterised using descriptive analysis, correlation matrices, enrichment factor (EF, stoichiometric analysis and chemical mass closure (CMC. For source apportionment purposes, a combination of positive matrix factorisation (PMF and multi-linear regression (MLR was employed. Further, meteorological–gaseous parameters were incorporated into each analysis for improved assessment. In addition, secondary data of total suspended particulate (TSP and coarse particulate matter (PM10 sampled at the same location and time with this study (collected by Malaysian Meteorological Department were used for PM ratio assessment. The results showed that PM2.5 mass averaged at 28 ± 18 µg m−3, 2.8-fold higher than the World Health Organisation (WHO annual guideline. On a daily basis, the PM2.5 mass ranged between 6 and 118 µg m−3 with the daily WHO guideline exceeded 43 % of the time. The north-east (NE monsoon was the only season with less than 50 % sample exceedance of the daily WHO guideline. On an annual scale, PM2.5 mass correlated positively with temperature (T and wind speed (WS but negatively with relative humidity (RH. With the exception of NOx, the gases analysed (CO, NO2, NO and SO2 were found to significantly influence the PM2.5 mass. Seasonal variability unexpectedly showed that rainfall, WS and wind direction (WD did not

Dataset on statistical analysis of editorial board composition of Hindawi journals indexed in Emerging sources citation index

Directory of Open Access Journals (Sweden)

Hilary I. Okagbue

2018-04-01

Full Text Available This data article contains the statistical analysis of the total, percentage and distribution of editorial board composition of 111 Hindawi journals indexed in Emerging Sources Citation Index (ESCI across the continents. The reliability of the data was shown using correlation, goodness-of-fit test, analysis of variance and statistical variability tests. Keywords: Hindawi, Bibliometrics, Data analysis, ESCI, Random, Smart campus, Web of science, Ranking analytics, Statistics

The Effect of Soil Contamination on Chemical Composition and Quality of Aronia (Aronia melanocarpa) Fruits

OpenAIRE

Violina R. Angelova; Sava G. Tabakov; Aleksander B. Peltekov; Krasimir I. Ivanov

2017-01-01

A field study was conducted to evaluate the chemical composition and quality of the Aronia fruits, as well as the possibilities of Aronia cultivation on soils contaminated with heavy metals. The experiment was performed on an agricultural field contaminated by the Non-Ferrous-Metal Works (NFMW) near Plovdiv, Bulgaria. The study included four varieties of Aronia; Aron variety, Hugin variety, Viking variety and Nero variety. The Aronia was cultivated according to the conventional technology on ...

Evaluation of water quality at the source of streams of the Sinos River Basin, southern Brazil

Directory of Open Access Journals (Sweden)

T Benvenuti

Full Text Available The Sinos River Basin (SRB is located in the northeastern region of the state of Rio Grande do Sul (29º20' to 30º10'S and 50º15' to 51º20'W, southern Brazil, and covers two geomorphologic provinces: the southern plateau and the central depression. It is part of the Guaíba basin, has an area of approximately 800 km2 and contains 32 counties. The basin provides drinking water for 1.6 million inhabitants in one of the most important industrial centres in Brazil. This study describes different water quality indices (WQI used for the sub-basins of three important streams in the SRB: Pampa, Estância Velha/Portão and Schmidt streams. Physical, chemical and microbiological parameters assessed bimonthly using samples collected at each stream source were used to calculate the Horton Index (HI, the Dinius Index (DI and the water quality index adopted by the US National Sanitation Foundation (NSF WQI in the additive and multiplicative forms. These indices describe mean water quality levels at the streams sources. The results obtained for these 3 indexes showed a worrying scenario in which water quality has already been negatively affected at the sites where three important sub-basins in the Sinos River Basin begin to form.

Drinking water treatment plant costs and source water quality: An updated case study (2013-2016) Abstract

Science.gov (United States)

Watershed protection can play an important role in producing safe drinking water. However, many municipalities and drinking water treatment plants (DWTPs) lack the information on the potential benefits of watershed protection as an approach to improving source water quality. This...

Sex-specific relationships of physical activity, body composition, and muscle quality with lower-extremity physical function in older men and women.

Science.gov (United States)

Straight, Chad R; Brady, Anne O; Evans, Ellen

2015-03-01

This study aims to determine the sex-specific relationships of physical activity, body composition, and muscle quality with lower-extremity physical function in older men and women. Seventy-nine community-dwelling men (n = 39; mean [SD] age, 76.1 [6.2] y; mean [SD] body mass index, 27.3 [3.8] kg/m(2)) and women (n = 40; mean [SD] age, 75.8 [5.5] y; mean [SD] body mass index, 27.0 [3.8] kg/m(2)) were assessed for physical activity via questionnaire, body composition via dual-energy x-ray absorptiometry scanning, leg extension power using the Nottingham power rig, and muscle quality (W/kg; the ratio of leg extension power [W] to lower-body mineral-free lean mass [kg]). A composite measure of physical function was obtained by summing Z scores from the 6-minute walk, 8-ft up-and-go test, and 30-second chair-stand test. As expected, men had significantly greater levels of physical activity, lower adiposity, greater lean mass, higher leg extension power, and greater muscle quality compared with women (all P physical activity were the strongest predictors of lower-extremity physical function in men and independently explained 42% and 29% of the variance, respectively. In women, muscle quality (16%) and percent body fat (12%) were independent predictors after adjustment for covariates. Muscle quality is the strongest predictor of lower-extremity physical function in men and women, but sex impacts the importance of physical activity and adiposity. These findings suggest that older men and women may benefit from different intervention strategies for preventing physical disability and also highlight the importance of weight management for older women to preserve physical function.

A Transformational Journey: Compositional Changes in Organic Matter during Desorption from Sediments

Science.gov (United States)

Matiasek, S. J.; Pellerin, B. A.; Spencer, R.; Bergamaschi, B. A.; Hernes, P.

2016-12-01

The release of organic matter (OM) from suspended particles via desorption is a critical component of OM cycling since dissolved OM (DOM) fuels aquatic ecosystems and is a precursor for disinfection by-products formation. This study assessed the elemental and molecular composition of DOM desorbed abiotically from sediments and soils of an irrigated agricultural watershed of northern California. Relative to mineral-bound OM, the released DOM was nitrogen-poor (lower carbon:nitrogen ratios) and depleted in amino acids and lignin phenols (lower carbon-normalized yields). Water-extracted DOM appeared substantially more degraded than its parent particulate OM with increased molar contributions of acidic amino acids, non-protein amino acids, and acidic lignin phenols, all molecular indicators of a more extensively processed OM pool. Desorption processes also significantly altered lignin compositional ratios which help distinguish vascular-plant sources of DOM. Specific optical parameters, including spectral slope, specific UV absorbance at 254 nm (SUVA254), and fluorescence index (FI), did not constitute useful proxies for the desorbed DOM pool, while absorption coefficients and fluorescence peak intensities were strongly correlated with extracted DOM concentrations and composition. This study highlights the profound impact of desorption on DOM composition which, if unaccounted for, could lead to misinterpretations of common biomarkers and optical proxies used to predict DOM sources and reactivity. Our findings suggest that sediments contribute a biogeochemically distinct source of DOM to surface waters, with potential impacts on aquatic health and drinking water quality.

Food source quality and ant dominance hierarchy influence the outcomes of ant-plant interactions in an arid environment

Science.gov (United States)

Flores-Flores, Rocío Vianey; Aguirre, Armando; Anjos, Diego V.; Neves, Frederico S.; Campos, Ricardo I.; Dáttilo, Wesley

2018-02-01

In this study, we conducted a series of experiments in a population of Vachellia constricta (Fabaceae) in the arid Tehuacan-Cuicatláan valley, Mexico, in order to evaluate if the food source quality and ant dominance hierarchy influence the outcomes of ant-plant interactions. Using an experiment with artificial nectaries, we observed that ants foraging on food sources with higher concentration of sugar are quicker in finding and attacking potential herbivorous insects. More specifically, we found that the same ant species may increase their defence effectiveness according to the quality of food available. These findings indicate that ant effectiveness in plant protection is context-dependent and may vary according to specific individual characteristics of plants. In addition, we showed that competitively superior ant species tend to dominate plants in periods with high nectar activity, emphasizing the role of the dominance hierarchy structuring ant-plant interactions. However, when high sugar food sources were experimentally available ad libitum, the nocturnal and competitively superior ant species, Camponotus atriceps, did not dominate the artificial nectaries during the day possibly due to limitation of its thermal tolerance. Therefore, temporal niche partitioning may be allowing the coexistence of two dominant ant species (Camponotus rubritorax during the day and C. atriceps at night) on V. constricta. Our findings indicate that the quality of the food source, and temporal shifts in ant dominance are key factors which structure the biotic plant defences in an arid environment.

A portable x-ray source and method for radiography

International Nuclear Information System (INIS)

Golovanivsky, K.S.

1996-01-01

A portable x-ray source that produces a sufficient x-ray flux to produce high quality x-ray images on x-ray films. The source includes a vacuum chamber filled with a heavy atomic weight gas at low pressure and an x-ray emitter. The chamber is in a magnetic field and an oscillating electric field and generates electron cyclotron resonance (ECR) plasma having a ring of energetic electrons inside the chamber. The electrons bombard the x-ray emitter which in turn produces x-ray. A pair of magnetic members generate an axisymmetric magnetic mirror trap inside the chamber. The chamber may be nested within a microwave resonant cavity and between the magnets or the chamber and the microwave cavity may be a single composite structure. (author)

Water quality, sources of nitrate, and chemical loadings in the Geronimo Creek and Plum Creek watersheds, south-central Texas, April 2015–March 2016

Science.gov (United States)

Lambert, Rebecca B.; Opsahl, Stephen P.; Musgrove, MaryLynn

2017-12-22

Located in south-central Texas, the Geronimo Creek and Plum Creek watersheds have long been characterized by elevated nitrate concentrations. From April 2015 through March 2016, an assessment was done by the U.S. Geological Survey, in cooperation with the Guadalupe-Blanco River Authority and the Texas State Soil and Water Conservation Board, to characterize nitrate concentrations and to document possible sources of elevated nitrate in these two watersheds. Water-quality samples were collected from stream, spring, and groundwater sites distributed across the two watersheds, along with precipitation samples and wastewater treatment plant (WWTP) effluent samples from the Plum Creek watershed, to characterize endmember concentrations and isotopic compositions from April 2015 through March 2016. Stream, spring, and groundwater samples from both watersheds were collected during four synoptic sampling events to characterize spatial and temporal variations in water quality and chemical loadings. Water-quality and -quantity data from the WWTPs and stream discharge data also were considered. Samples were analyzed for major ions, selected trace elements, nutrients, and stable isotopes of water and nitrate.The dominant land use in both watersheds is agriculture (cultivated crops, rangeland, and grassland and pasture). The upper part of the Plum Creek watershed is more highly urbanized and has five major WWTPs; numerous smaller permitted wastewater outfalls are concentrated in the upper and central parts of the Plum Creek watershed. The Geronimo Creek watershed, in contrast, has no WWTPs upstream from or near the sampling sites.Results indicate that water quality in the Geronimo Creek watershed, which was evaluated only during base-flow conditions, is dominated by groundwater, which discharges to the stream by numerous springs at various locations. Nitrate isotope values for most Geronimo Creek samples were similar, which indicates that they likely have a common source (or

Funding source and the quality of reports of chronic wounds trials: 2004 to 2011.

Science.gov (United States)

Hodgson, Robert; Allen, Richard; Broderick, Ellen; Bland, J Martin; Dumville, Jo C; Ashby, Rebecca; Bell-Syer, Sally; Foxlee, Ruth; Hall, Jill; Lamb, Karen; Madden, Mary; O'Meara, Susan; Stubbs, Nikki; Cullum, Nicky

2014-01-14

Critical commentaries suggest that wound care randomised controlled trials (RCTs) are often poorly reported with many methodological flaws. Furthermore, interventions in chronic wounds, rather than being drugs, are often medical devices for which there are no requirements for RCTs to bring products to market. RCTs in wounds trials therefore potentially represent a form of marketing. This study presents a methodological overview of chronic wound trials published between 2004 and 2011 and investigates the influence of industry funding on methodological quality. A systematic search for RCTs for the treatment of chronic wounds published in the English language between 2004 and 2011 (inclusive) in the Cochrane Wounds Group Specialised Register of Trials was carried out.Data were extracted on aspects of trial design, conduct and quality including sample size, duration of follow-up, specification of a primary outcome, use of surrogate outcomes, and risks of bias. In addition, the prevalence of industry funding was assessed and its influence on the above aspects of trial design, conduct and quality was assessed. A total of 167 RCTs met our inclusion criteria. We found chronic wound trials often have short durations of follow-up (median 12 weeks), small sample sizes (median 63), fail to define a primary outcome in 41% of cases, and those that do define a primary outcome, use surrogate measures of healing in 40% of cases. Only 40% of trials used appropriate methods of randomisation, 25% concealed allocation and 34% blinded outcome assessors. Of the included trials, 41% were wholly or partially funded by industry, 33% declared non-commercial funding and 26% did not report a funding source. Industry funding was not statistically significantly associated with any measure of methodological quality, though this analysis was probably underpowered. This overview confirms concerns raised about the methodological quality of RCTs in wound care and illustrates that greater efforts must

Steps towards single source--collecting data about quality of life within clinical information systems.

Science.gov (United States)

Fritz, Fleur; Ständer, Sonja; Breil, Bernhard; Dugas, Martin

2010-01-01

Information about the quality of life from patients being treated in routine medical care is important for the attending physician. This data is also needed in research for example to evaluate the therapy and the course of the disease respectively. Especially skin diseases often negatively affect the quality of life. Therefore we aimed to design a concept to collect such data during treatment and use it for both medical care and research in the setting of dermatology. We performed a workflow analysis and implemented a designated form using the tools of the local clinical information system. Quality of life data is now collected within the clinical information system during treatment and is used for discharge letters, progress overviews as well as research about the treatment and course of disease. This concept which contributes to the single source approach was feasible within dermatology and is ready to be expanded into other domains.

Changes imposed by pyrolysis, thermal gasification and incineration on composition and phosphorus fertilizer quality of municipal sewage sludge.

Science.gov (United States)

Thomsen, Tobias Pape; Sárossy, Zsuzsa; Ahrenfeldt, Jesper; Henriksen, Ulrik B; Frandsen, Flemming J; Müller-Stöver, Dorette Sophie

2017-08-01

Fertilizer quality of ash and char from incineration, gasification and pyrolysis of a single municipal sewage sludge sample were investigated by comparing composition and phosphorus (P) plant availability. A process for post oxidation of gasification ash and pyrolysis char was developed and the oxidized materials were investigated as well. Sequential extraction with full elemental balances of the extracted pools as well as scanning electron microscopy with energy dispersive X-ray spectroscopy were used to investigate the mechanisms driving the observed differences in composition and P plant availability in a short-term soil incubation study. The compositional changes related mainly to differences in the proximate composition as well as to the release of especially nitrogen, sulfur, cadmium and to some extent, phosphorus (P). The cadmium load per unit of P was reduced with 75-85% in gasification processes and 10-15% in pyrolysis whereas no reduction was observed in incineration processes. The influence on other heavy metals was less pronounced. The plant availability of P in the substrates varied from almost zero to almost 100% of the plant availability of P in the untreated sludge. Post-oxidized slow pyrolysis char was found to be the substrate with the highest P fertilizer value while ash from commercial fluid bed sludge incineration had the lowest P fertilizer quality. The high P fertilizer value in the best substrate is suggested to be a function of several different mechanisms including structural surface changes and improvements in the association of P to especially magnesium, calcium and aluminum. Copyright © 2017 Elsevier Ltd. All rights reserved.

CHANGES IN THE QUALITY OF DRESSED CHICKEN OBTAINED FROM DIFFERENT SOURCES DURING FROZEN STORAGE

Directory of Open Access Journals (Sweden)

Santosh Kumar HT

2014-06-01

Full Text Available This present study examines the preservation quality of dressed chicken procured from different sources of processing during storage at –18±1ºC. Breast portion of the dressed birds obtained from three different sources, viz. market/road side slaughtered chicken (MSC, retail slaughtered chicken (RSC, and scientifically slaughtered chicken (SSC, were cut into chunks, divided into 250 g portions, packed in polyethylene bags, stored at –18±1ºC and evaluated at 30 days intervals for changes in quality attributes. Frozen storage had no marked influence on pH change of the samples. SSC samples had higher extract release volume (15.34±0.08 to 13.45±0.93 ml than MSC (13.00±0.19 to 9.91±0.97 ml and RSC samples (13.65±0.24 to 11.70±1.21ml. There was significant increase (P<0.05 in thiobarbituric acid of all three sample types during storage but values were well below the threshold level of spoilage. SSC samples showed lower tyrosine content throughout frozen storage compared to MSC and RSC samples. A significant decline in microbial load, viz. total viable count, coliform count, psychrophilic count and yeast and moulds count were noticed during frozen storage. Organoleptic attributes, viz. appearance, flavour, texture and overall palatability were not affected due to frozen storage except juiciness in MSC samples which decreased (P<0.05 from 6.53±0.13 to 5.96±0.11 on 90 days of storage. Although the scientifically slaughtered chicken had better quality, all the sample types could be stored at –18±1ºC till 90 days without much deterioration in their quality.

Identification of the sources of metal (lead) contamination in drinking waters in north-eastern Tasmania using lead isotopic compositions.

Science.gov (United States)

Harvey, P J; Handley, H K; Taylor, M P

2015-08-01

This study utilises a range of scientific approaches, including lead isotopic compositions, to differentiate unknown sources of ongoing lead contamination of a drinking water supply in north-eastern Tasmania, Australia. Drinking water lead concentrations are elevated above the Australian Drinking Water Guideline (10 μg/L), reaching 540 μg/L in the supply network. Water lead isotopic compositions from the town of Pioneer ((208)Pb/(207)Pb 2.406, (206)Pb/(207)Pb 1.144 to (208)Pb/(207)Pb 2.360, (206)Pb/(207)Pb 1.094) and Ringarooma ((208)Pb/(207)Pb 2.398, (206)Pb/(207)Pb 1.117) are markedly different from the local bedrock ((208)Pb/(207)Pb 2.496, (206)Pb/(207)Pb 1.237). The data show that the lead in the local waters is sourced from a combination of dilapidated drinking water infrastructure, including lead jointed pipelines, end-of-life polyvinyl chloride pipes and household plumbing. Drinking water is being inadvertently contaminated by aging infrastructure, and it is an issue that warrants investigation to limit the burden of disease from lead exposure.

Challenges with secondary use of multi-source water-quality data in the United States

Science.gov (United States)

Sprague, Lori A.; Oelsner, Gretchen P.; Argue, Denise M.

2017-01-01

Combining water-quality data from multiple sources can help counterbalance diminishing resources for stream monitoring in the United States and lead to important regional and national insights that would not otherwise be possible. Individual monitoring organizations understand their own data very well, but issues can arise when their data are combined with data from other organizations that have used different methods for reporting the same common metadata elements. Such use of multi-source data is termed “secondary use”—the use of data beyond the original intent determined by the organization that collected the data. In this study, we surveyed more than 25 million nutrient records collected by 488 organizations in the United States since 1899 to identify major inconsistencies in metadata elements that limit the secondary use of multi-source data. Nearly 14.5 million of these records had missing or ambiguous information for one or more key metadata elements, including (in decreasing order of records affected) sample fraction, chemical form, parameter name, units of measurement, precise numerical value, and remark codes. As a result, metadata harmonization to make secondary use of these multi-source data will be time consuming, expensive, and inexact. Different data users may make different assumptions about the same ambiguous data, potentially resulting in different conclusions about important environmental issues. The value of these ambiguous data is estimated at \\$US12 billion, a substantial collective investment by water-resource organizations in the United States. By comparison, the value of unambiguous data is estimated at \\$US8.2 billion. The ambiguous data could be preserved for uses beyond the original intent by developing and implementing standardized metadata practices for future and legacy water-quality data throughout the United States.

[Influence of the substrate composition in extensive green roof on the effluent quality].

Science.gov (United States)

Chen, Yu-Lin; Li, Tian; Gu, Jun-Qing

2014-11-01

By monitoring the effluent quality from different green roof assemblies during several artificial rain events, the main pollutant characteristics and the influence of substrate composition in extensive green roof on the effluent quality were studied. Results showed that the main pollutants in the effluent were N, P and COD; with the increase of cumulative rain, the concentrations of pollutants in the effluent decreased, which had obvious leaching effect; The average concentrations of heavy metals in the early effluent from all assemblies reached drinking water standard, including the assemblies using crushed bricks; When garden soil and compost were used as organic matter, the assemblies had serious leaching of nutrient substance. After the accumulated rainfall reached 150 mm, the TN, TP and COD concentrations of effluent were 2.93, 0.73 and 78 mg x L(-1), respectively, which exceeded the Surface water V class limit. By means of application of the Water Treatment Residual, the leaching of TP from green planting soil was decreased by about 60%. The inorganic compound soil had better effluent quality, however we also need to judge whether the substrate could be applied in extensive green roof or not, by analyzing its ability of water quantity reduction and the plant growth situation.

Application of customised bacterial inoculants for grass haylage production and its effectiveness on nutrient composition and fermentation quality of haylage.

Science.gov (United States)

Soundharrajan, Ilavenil; Kim, Da Hye; Srisesharam, Srigopalram; Kuppusamy, Palaniselvam; Park, Hyung Soo; Yoon, Yong Hee; Kim, Won Ho; Song, Young Gil; Choi, Ki Choon

2017-10-01

The present study aimed to investigate the efficacy of customised Lactobacillus plantarum KCC-10, KCC-19 and K-46 on nutrient composition and fermentation quality of low moisture Italian ryegrass (IRG) forage. An addition of customised bacterial inoculants (CBI) did not affect the nutrient compositions and digestibility rates of haylage. The lactic acid content was higher in CBI-inoculated haylage, whereas the amount of acetic acid and butyric acid production was significantly reduced than the control. CBI-inoculated haylage exhibited higher numbers of bacterial colonies that reduced the pH of the haylage. Low pH in haylage is an important criterion for preventing undesirable microbial growth and improves fermentation quality of haylage. PCR studies indicated that the DNA of L. plantarum was predominantly amplified. It evidenced that the CBI is the main reason behind the improvement of haylage fermentation as compared to control. Overall results suggested that KCC-10, KCC-19 and K-46 are considered as potent strains for improving fermentation quality of low moisture forage and preserve its stability for a long time.

A Composite Indicator to Assess the Quality of Care in the Management of Patients With Rheumatoid Arthritis in Outpatient Rheumatology Clinics.

Science.gov (United States)

Martín-Martínez, María Auxiliadora; Andreu-Sanchez, Jose Luis; Sanchez-Alonso, Fernando; Corominas, Hector; Perez-Venegas, Jose Javier; Roman-Ivorra, Jose Andres; Alperi, Mercedes; Blanco-Alonso, Ricardo; Caliz, Rafael; Chamizo-Carmona, Eugenio; Graña-Gil, Jenaro; Hernández, Blanca; Marras, Carlos; Mazzucchelli, Ramon; Medina Luezas, Julio Antonio; Naranjo-Hernández, Antonio; Ortiz, Ana; Roselló, Rosa; Sanchez-Nievas, Ginés; Sanmartí, Raimon; Vela-Casasempere, Paloma

2017-08-05

The current guidelines in the treatment of rheumatoid arthritis (RA) include the early diagnosis and early use of disease modifying drugs to achieve remission or low disease activity level, known as "Treat to Target" (T2T). The objective of this study is to develop a composite indicator (CI) to evaluate the quality of care in the management of patients with RA, according to the T2T strategy and other general recommendations concerning the management of these patients. The phases of the construction of the CI were: 1) selection of quality criteria through expert judgment; 2) prioritization of the criteria, according to relevance and feasibility, applying the Delphi methodology (two rounds) involving 20 experts; 3) design of quality indicators; and 4) calculation of the weighted CI, using the mean value in relevance and feasibility granted by the experts. The source of information for the calculation of the CI are the medical records of patients with RA. Twelve criteria out of 37 required a second Delphi round. Thirty-one criteria were prioritized. These criteria presented a median in relevance and feasibility greater than or equal to 7.5, with an interquartile range of less than 3.5, and a level of agreement (score greater than or equal to 8) greater than or equal to 80%. The constructed CI allows us to evaluate the quality of care of patients with RA following the T2T strategy in the rheumatology units of Spanish hospitals, offering a valid and easily interpretable summary measure. Copyright © 2017 Elsevier España, S.L.U. and Sociedad Española de Reumatología y Colegio Mexicano de Reumatología. All rights reserved.

Sources And Compositional Distribution Of Polycyclic Aromatic ...

African Journals Online (AJOL)

For molecular mass 178, an anthracene to anthracene plus phenanthrene ratio ≤ 0.10 was taken as indication of petroleum related sources, while a ratio > 0.10 indicated dominance of combustion related sources. For molecular mass 202, a fluoranthene to fluoranthene plus pyrene ratio ≤ 0.50 was indication of petroleum ...

Determinants of the Sensory Quality of Półgęsek in Relation to Volatile Compounds and Chemical Composition

Directory of Open Access Journals (Sweden)

Nowicka Katarzyna

2017-12-01

Full Text Available The objective of this study was to determine the sensory quality of a specific Polish traditional product made from cured and then smoked goose meat (półgęsek in relation to its volatile compounds and chemical composition. In general, the examined samples contained 66.2% water, 12.2% fat, 17.9% protein, 1.8% connective tissue, and 2.3% NaCl. Moreover, 47 volatile compounds were identified and quantified. The typical decomposition products derived from lipid oxidation, amino acid degradation, carbohydrate fermentation and microbial esterification were the main volatiles detected in all the samples. The volatiles generated by the smoking process and the ones originating from spices were also observed. The results of the sensory evaluation indicated that all the samples of the analyzed products were characterized by a high overall quality. Results of the Principal Component Analysis (PCA showed, however, that specific groups of products have their own unique sensory profile. Additionally, the sensory analysis confirmed the significant role of the chemical composition and volatile compounds in the development of the overall quality of półgęsek.

INTEGRAL INDEX OF OPERATION QUALITY FOR EVALUATION OF IMPACT OF DISTRIBUTIVE GENERATION SOURCES ON ELECTRIC NETWORK MODES

Directory of Open Access Journals (Sweden)

Petro D. Lezhniuk

2017-06-01

Full Text Available Method of operation quality evaluation of electric network, comprising renewable sources of energy (RSE is considered. Integral index that enables to evaluate the impact of RSE on energy losses and its quality as well as balance reliability in electric network is suggested. Mathematical model is constructed, taking into account the assumption that electric network with RSE may be in various operation modes, characterized by different technical economic indices. To determine the integral index of operation quality of electric network with RSE in all possible states tools of Markov processes theory and criterial method are used.

Effect of modified atmosphere packaging and addition of calcium hypochlorite on the atmosphere composition, colour and microbial quality of mushrooms

CSIR Research Space (South Africa)

Kuyper, L

1993-01-01

Full Text Available The effect of modified atmosphere packaging in combination with the addition of calcium hypochlorite on the atmosphere composition, colour and microbial quality of mushrooms was investigated. A modified atmosphere which slowed down discolouration...

Multi-dimensional water quality assessment of an urban drinking water source elucidated by high resolution underwater towed vehicle mapping.

Science.gov (United States)

Lock, Alan; Spiers, Graeme; Hostetler, Blair; Ray, James; Wallschläger, Dirk

2016-04-15

Spatial surveys of Ramsey Lake, Sudbury, Ontario water quality were conducted using an innovative underwater towed vehicle (UTV) equipped with a multi-parameter probe providing real-time water quality data. The UTV revealed underwater vent sites through high resolution monitoring of different spatial chemical characteristics using common sensors (turbidity, chloride, dissolved oxygen, and oxidation/reduction sensors) that would not be feasible with traditional water sampling methods. Multi-parameter probe vent site identification is supported by elevated alkalinity and silica concentrations at these sites. The identified groundwater vent sites appear to be controlled by bedrock fractures that transport water from different sources with different contaminants of concern. Elevated contaminants, such as, arsenic and nickel and/or nutrient concentrations are evident at the vent sites, illustrating the potential of these sources to degrade water quality. Copyright © 2016 Elsevier Ltd. All rights reserved.

Influence of Production Method on the Chemical Composition, Foaming Properties, and Quality of Australian Carbonated and Sparkling White Wines.

Science.gov (United States)

Culbert, Julie A; McRae, Jacqui M; Condé, Bruna C; Schmidtke, Leigh M; Nicholson, Emily L; Smith, Paul A; Howell, Kate S; Boss, Paul K; Wilkinson, Kerry L

2017-02-22

The chemical composition (protein, polysaccharide, amino acid, and fatty acid/ethyl ester content), foaming properties, and quality of 50 Australian sparkling white wines, representing the four key production methods, that is, Méthode Traditionelle (n = 20), transfer (n = 10), Charmat (n = 10), and carbonation (n = 10), were studied. Méthode Traditionelle wines were typically rated highest in quality and were higher in alcohol and protein contents, but lower in residual sugar and total phenolics, than other sparkling wines. They also exhibited higher foam volume and stability, which might be attributable to higher protein concentrations. Bottle-fermented Méthode Traditionelle and transfer wines contained greater proportions of yeast-derived mannoproteins, whereas Charmat and carbonated wines were higher in grape-derived rhamnogalacturonans; however, total polysaccharide concentrations were not significantly different between sparkling wine styles. Free amino acids were most abundant in carbonated wines, which likely reflects production via primary fermentation only and/or the inclusion of nontraditional grape varieties. Fatty acids and their esters were not correlated with foaming properties, but octanoic and decanoic acids and their ethyl esters were present in Charmat and carbonated wines at significantly higher concentrations than in bottle-fermented wines and were negatively correlated with quality ratings. Research findings provide industry with a better understanding of the compositional factors driving the style and quality of sparkling white wine.

Measuring Data Quality Through a Source Data Verification Audit in a Clinical Research Setting.

Science.gov (United States)

Houston, Lauren; Probst, Yasmine; Humphries, Allison

2015-01-01

Health data has long been scrutinised in relation to data quality and integrity problems. Currently, no internationally accepted or "gold standard" method exists measuring data quality and error rates within datasets. We conducted a source data verification (SDV) audit on a prospective clinical trial dataset. An audit plan was applied to conduct 100% manual verification checks on a 10% random sample of participant files. A quality assurance rule was developed, whereby if >5% of data variables were incorrect a second 10% random sample would be extracted from the trial data set. Error was coded: correct, incorrect (valid or invalid), not recorded or not entered. Audit-1 had a total error of 33% and audit-2 36%. The physiological section was the only audit section to have <5% error. Data not recorded to case report forms had the greatest impact on error calculations. A significant association (p=0.00) was found between audit-1 and audit-2 and whether or not data was deemed correct or incorrect. Our study developed a straightforward method to perform a SDV audit. An audit rule was identified and error coding was implemented. Findings demonstrate that monitoring data quality by a SDV audit can identify data quality and integrity issues within clinical research settings allowing quality improvement to be made. The authors suggest this approach be implemented for future research.

Implementing the EuroFIR Document and Data Repositories as accessible resources of food composition information.

Science.gov (United States)

Unwin, Ian; Jansen-van der Vliet, Martine; Westenbrink, Susanne; Presser, Karl; Infanger, Esther; Porubska, Janka; Roe, Mark; Finglas, Paul

2016-02-15

The EuroFIR Document and Data Repositories are being developed as accessible collections of source documents, including grey literature, and the food composition data reported in them. These Repositories will contain source information available to food composition database compilers when selecting their nutritional data. The Document Repository was implemented as searchable bibliographic records in the Europe PubMed Central database, which links to the documents online. The Data Repository will contain original data from source documents in the Document Repository. Testing confirmed the FoodCASE food database management system as a suitable tool for the input, documentation and quality assessment of Data Repository information. Data management requirements for the input and documentation of reported analytical results were established, including record identification and method documentation specifications. Document access and data preparation using the Repositories will provide information resources for compilers, eliminating duplicated work and supporting unambiguous referencing of data contributing to their compiled data. Copyright © 2014 Elsevier Ltd. All rights reserved.

[Kinetic simulation of enhanced biological phosphorus removal with fermentation broth as carbon source].

Science.gov (United States)

Zhang, Chao; Chen, Yin-Guang

2013-07-01

As a high-quality carbon source, fermentation broth could promote the phosphorus removal efficiency in enhanced biological phosphorus removal (EBPR). The transformation of substrates in EBPR fed with fermentation broth was well simulated using the modified activated sludge model No. 2 (ASM2) based on the carbon source metabolism. When fermentation broth was used as the sole carbon source, it was found that heterotrophic bacteria acted as a promoter rather than a competitor to the phosphorus accumulating organisms (PAO). When fermentation broth was used as a supplementary carbon source of real municipal wastewater, the wastewater composition was optimized for PAO growth; and the PAO concentration, which was increased by 3.3 times compared to that in EBPR fed with solely real municipal wastewater, accounting for about 40% of the total biomass in the reactor.

Effect of phytase in laying hen diets with different phosphorus sources

Directory of Open Access Journals (Sweden)

EM Casartelli

2005-06-01

Full Text Available An experiment was conducted to evaluate the effects of the enzyme phytase in diets formulated with different phosphorus sources on performance, eggshell quality and excretion of commercial laying hens. Two hundred and eighty-eight commercial Hyssex Brown laying hens were evaluated during two production phases, which included eight twenty-eight-day cycles, using a completely randomized design in a 3x2 factorial with six replicates of eight birds per treatment. Three phosphorus sources (calcium and sodium phosphate, micro-granulated dicalcium phosphate and triple super phosphate and two phytase levels (0 or 1000 FTU/kg diet were tested in the composition of the diets. After the post-peak period, triple super phosphate decreased bird performance and eggshell quality. It was possible to reduce the levels of phosphorus supplementation when phytase was added to the diet. Besides, phytase supplementation reduced phosphorus, calcium and nitrogen excretions, but affected mean egg weight at production peak.

Production of polymer-plaster composite by gamma irradiation

International Nuclear Information System (INIS)

Gazineu, Maria Helena Paranhos; Santos, Valdemir Alexandre dos; Dantas, Carlos Costa

2009-01-01

The estimated amount of plaster wastes in the construction industry is 45%. The reduction of this waste is of concern, because the cost of lost material and the waste management can affect the competitiveness of the company. The mixture of plaster with a particular resin generates a composite, which gives the pre-molded obtained from this mixture, special properties. In this case, the plasticity of the plaster generates pre-molded products with wealth of details. Additionally, the use of nuclear techniques for the initiation of polymerization reaction for obtaining this type of composite can eliminate the need for a heat source which is the conventional way to obtain polymerization, considerably reducing the costs of the process. As a function of the availability and the cost of styrene monomer, in the initial phase of the research test samples were prepared from plaster composites with this type of material. The test samples, composed of plaster and styrene, were irradiated in the presence of a Cs-137 (662 keV) gamma source for a period of time of two days in an air pressurized chamber. Tests of resistance to compression, tensile strength in bending and water absorption, were based on a type of experimental design, CCRD (Central Composite Rotatable Design). The percent average weight of polymer by weight of the test sample was 14.0%. The presence of a polymerized resin gives the sample qualities such as being highly impervious to water and high mechanical strength, allowing its use in the manufacture of different types of materials. (author)

Atmospheric aerosol compositions and sources at two national background sites in northern and southern China

Science.gov (United States)

Zhu, Qiao; He, Ling-Yan; Huang, Xiao-Feng; Cao, Li-Ming; Gong, Zhao-Heng; Wang, Chuan; Zhuang, Xin; Hu, Min

2016-08-01

Although China's severe air pollution has become a focus in the field of atmospheric chemistry and the mechanisms of urban air pollution there have been researched extensively, few field sampling campaigns have been conducted at remote background sites in China, where air pollution characteristics on a larger scale are highlighted. In this study, an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS), together with an Aethalometer, was deployed at two of China's national background sites in northern (Lake Hongze site; 33.23° N, 118.33° E; altitude 21 m) and southern (Mount Wuzhi site; 18.84° N, 109.49° E; altitude 958 m) China in the spring seasons in 2011 and 2015, respectively, in order to characterize submicron aerosol composition and sources. The campaign-average PM1 concentration was 36.8 ± 19.8 µg m-3 at the northern China background (NCB) site, which was far higher than that at the southern China background (SCB) site (10.9 ± 7.8 µg m-3). Organic aerosol (OA) (27.2 %), nitrate (26.7 %), and sulfate (22.0 %) contributed the most to the PM1 mass at NCB, while OA (43.5 %) and sulfate (30.5 %) were the most abundant components of the PM1 mass at SCB, where nitrate only constituted a small fraction (4.7 %) and might have contained a significant amount of organic nitrates (5-11 %). The aerosol size distributions and organic aerosol elemental compositions all indicated very aged aerosol particles at both sites. The OA at SCB was more oxidized with a higher average oxygen to carbon (O / C) ratio (0.98) than that at NCB (0.67). Positive matrix factorization (PMF) analysis was used to classify OA into three components, including a hydrocarbon-like component (HOA, attributed to fossil fuel combustion) and two oxygenated components (OOA1 and OOA2, attributed to secondary organic aerosols from different source areas) at NCB. PMF analysis at SCB identified a semi-volatile oxygenated component (SV-OOA) and a low-volatility oxygenated

Composites from wood and plastics

Science.gov (United States)

Craig Clemons

2010-01-01

Composites made from thermoplastics and fillers or reinforcements derived from wood or other natural fibers are a dynamic research area encompassing a wide variety of composite materials. For example, as the use of biopolymers grows, wood and other natural fiber sources are being investigated as renewable sources of fillers and reinforcements to modify performance....

Determination of Cr, Mn, Si, and Ni in carbon steels by optical emission spectrometry with spark source

International Nuclear Information System (INIS)

Garcia Gonzalez, M.A.; Pomares Alfonso, M.; Mora Lopez, L.

1995-01-01

Elemental composition of steels determines some important of his characteristic moreover it is necessary to obtain their quality certification. Analytical procedure has performed for determination of Cr, Mn, Si and Ni in carbon steels by optical emission spectrometry with spark source. reproducibility of results is 5-11 %. Exactitude has tested with results that have obtained by internationally recognised methods-

Functional group composition of ambient and source organic aerosols determined by tandem mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Dron, J.; El Haddad, I.; Temime-Roussel, B.; Wortham, H.; Marchand, N. [Univ Aix Marseille, CNRS, Lab Chim Provence, Equipe Instrumentat and React Atmospher, UMR 6264, F-13331 Marseille 3 (France); Jaffrezo, J.L. [Univ Grenoble 1, CNRS, UMR 5183, Lab Glaciol and Geophys Environm, F-38402 St Martin Dheres (France)

2010-07-01

The functional group composition of various organic aerosols (OA) is investigated using a recently developed analytical approach based on atmospheric pressure chemical ionisation-tandem mass spectrometry (APCIMS/MS). The determinations of three functional groups contents are performed quantitatively by neutral loss (carboxylic and carbonyl groups, R-COOH and R-CO-R' respectively) and precursor ion (nitro groups, R-NO{sub 2}) scanning modes of a tandem mass spectrometer. Major organic aerosol sources are studied: vehicular emission and wood combustion for primary aerosol sources; and a secondary organic aerosol (SOA) produced through photooxidation of o-xylene. The results reveal significant differences in the functional group contents of these source aerosols. The laboratory generated SOA is dominated by carbonyls while carboxylics are preponderate in the wood combustion particles. On the other hand, vehicular emissions are characterised by a strong nitro content. The total amount of the three functional groups accounts for 1.7% (vehicular) to 13.5% (o-xylene photooxidation) of the organic carbon. Diagnostic functional group ratios are then used to tentatively discriminate sources of particles collected in an urban background environment located in an Alpine valley (Chamonix, France) during a strong winter pollution event. The three functional groups under study account for a total functionalization rate of 2.2 to 3.8% of the organic carbon in this ambient aerosol, which is also dominated by carboxylic moieties. In this particular case study of a deep alpine valley during winter, we show that the nitro- and carbonyl-to-carboxylic diagnostic ratios can be a useful tool to discriminate sources. In these conditions, the total OA concentrations are highly dominated by wood combustion OA. This result is confirmed by an organic markers source apportionment approach which assess a wood burning organic carbon contribution of about 60%. Finally, examples of functional

Functional group composition of ambient and source organic aerosols determined by tandem mass spectrometry

Directory of Open Access Journals (Sweden)

J. Dron

2010-08-01

Full Text Available The functional group composition of various organic aerosols (OA is investigated using a recently developed analytical approach based on atmospheric pressure chemical ionisation-tandem mass spectrometry (APCI-MS/MS. The determinations of three functional groups contents are performed quantitatively by neutral loss (carboxylic and carbonyl groups, R-COOH and R-CO-R´ respectively and precursor ion (nitro groups, R-NO₂ scanning modes of a tandem mass spectrometer. Major organic aerosol sources are studied: vehicular emission and wood combustion for primary aerosol sources; and a secondary organic aerosol (SOA produced through photooxidation of o-xylene. The results reveal significant differences in the functional group contents of these source aerosols. The laboratory generated SOA is dominated by carbonyls while carboxylics are preponderate in the wood combustion particles. On the other hand, vehicular emissions are characterised by a strong nitro content. The total amount of the three functional groups accounts for 1.7% (vehicular to 13.5% (o-xylene photooxidation of the organic carbon. Diagnostic functional group ratios are then used to tentatively discriminate sources of particles collected in an urban background environment located in an Alpine valley (Chamonix, France during a strong winter pollution event. The three functional groups under study account for a total functionalisation rate of 2.2 to 3.8% of the organic carbon in this ambient aerosol, which is also dominated by carboxylic moieties. In this particular case study of a deep alpine valley during winter, we show that the nitro- and carbonyl-to-carboxylic diagnostic ratios can be a useful tool to discriminate sources. In these conditions, the total OA concentrations are highly dominated by wood combustion OA. This result is confirmed by an organic markers source apportionment approach which assess a wood burning organic carbon contribution of about 60

Dual-source CT coronary imaging in heart transplant recipients: image quality and optimal reconstruction interval

International Nuclear Information System (INIS)

Bastarrika, Gorka; Arraiza, Maria; Pueyo, Jesus C.; Cecco, Carlo N. de; Ubilla, Matias; Mastrobuoni, Stefano; Rabago, Gregorio

2008-01-01

The image quality and optimal reconstruction interval for coronary arteries in heart transplant recipients undergoing non-invasive dual-source computed tomography (DSCT) coronary angiography was evaluated. Twenty consecutive heart transplant recipients who underwent DSCT coronary angiography were included (19 male, one female; mean age 63.1±10.7 years). Data sets were reconstructed in 5% steps from 30% to 80% of the R-R interval. Two blinded independent observers assessed the image quality of each coronary segments using a five-point scale (from 0 = not evaluative to 4=excellent quality). A total of 289 coronary segments in 20 heart transplant recipients were evaluated. Mean heart rate during the scan was 89.1±10.4 bpm. At the best reconstruction interval, diagnostic image quality (score ≥2) was obtained in 93.4% of the coronary segments (270/289) with a mean image quality score of 3.04± 0.63. Systolic reconstruction intervals provided better image quality scores than diastolic reconstruction intervals (overall mean quality scores obtained with the systolic and diastolic reconstructions 3.03±1.06 and 2.73±1.11, respectively; P<0.001). Different systolic reconstruction intervals (35%, 40%, 45% of RR interval) did not yield to significant differences in image quality scores for the coronary segments (P=0.74). Reconstructions obtained at the systolic phase of the cardiac cycle allowed excellent diagnostic image quality coronary angiograms in heart transplant recipients undergoing DSCT coronary angiography. (orig.)

Study on the performance of infrared thermal imaging light source for detection of impact defects in CFRP composite sandwich panels

Energy Technology Data Exchange (ETDEWEB)

Park, Hee Sang [R and D, Korea Research Institute of Smart Material and Structures System Association, Daejeon (Korea, Republic of); Choi, Man Yong; Kwon, Koo Ahn; Park, Jeong Hak; Choi, Won Jae [Safety measurement center, Korea research Institute of Standards and Science, Daejeon (Korea, Republic of); Jung, Hyun Chul [Dept. of Mechanical Engineering Chosun University, Gwangju (Korea, Republic of)

2017-04-15

Recently, composite materials have been mainly used in the main wings, ailerons, and fuselages of aircraft and rotor blades of helicopters. Composite materials used in rapid moving structures are subject to impact by hail, lightning, and bird strike. Such an impact can destroy fiber tissues in the composite materials as well as deform the composite materials, resulting in various problems such as weakened rigidity of the composite structure and penetration of water into tiny cracks. In this study, experiments were conducted using a 2 kW halogen lamp which is most frequently used as a light source, a 2 kW near-infrared lamp, which is used for heating to a high temperature, and a 6 kW xenon flash lamp which emits a large amount of energy for a moment. CFRP composite sandwich panels using Nomex honeycomb core were used as the specimens. Experiments were carried out under impact damages of 1, 4 and 8 J. It was found that the detection of defects was fast when the xenon flash lamp was used. The detection of damaged regions was excellent when the halogen lamp was used. Furthermore, the near-infrared lamp is an effective technology for showing the surface of a test object.

Study on the performance of infrared thermal imaging light source for detection of impact defects in CFRP composite sandwich panels

International Nuclear Information System (INIS)

Park, Hee Sang; Choi, Man Yong; Kwon, Koo Ahn; Park, Jeong Hak; Choi, Won Jae; Jung, Hyun Chul

2017-01-01

Recently, composite materials have been mainly used in the main wings, ailerons, and fuselages of aircraft and rotor blades of helicopters. Composite materials used in rapid moving structures are subject to impact by hail, lightning, and bird strike. Such an impact can destroy fiber tissues in the composite materials as well as deform the composite materials, resulting in various problems such as weakened rigidity of the composite structure and penetration of water into tiny cracks. In this study, experiments were conducted using a 2 kW halogen lamp which is most frequently used as a light source, a 2 kW near-infrared lamp, which is used for heating to a high temperature, and a 6 kW xenon flash lamp which emits a large amount of energy for a moment. CFRP composite sandwich panels using Nomex honeycomb core were used as the specimens. Experiments were carried out under impact damages of 1, 4 and 8 J. It was found that the detection of defects was fast when the xenon flash lamp was used. The detection of damaged regions was excellent when the halogen lamp was used. Furthermore, the near-infrared lamp is an effective technology for showing the surface of a test object

Point-Source Contributions to the Water Quality of an Urban Stream

Science.gov (United States)

Little, S. F. B.; Young, M.; Lowry, C.

2014-12-01

Scajaquada Creek, which runs through the heart of the city of Buffalo, is a prime example of the ways in which human intervention and local geomorphology can impact water quality and urban hydrology. Beginning in the 1920's, the Creek has been partially channelized and connected to Buffalo's combined sewer system (CSS). At Forest Lawn Cemetery, where this study takes place, Scajaquada Creek emerges from a 3.5-mile tunnel built to route stream flow under the city. Collocated with the tunnel outlet is a discharge point for Buffalo's CSS, combined sewer outlet (CSO) #53. It is at this point that runoff and sanitary sewage discharge regularly during rain events. Initially, this study endeavored to create a spatial and temporal picture for this portion of the Creek, monitoring such parameters as conductivity, dissolved oxygen, pH, temperature, and turbidity, in addition to measuring Escherichia coli (E. coli) concentrations. As expected, these factors responded directly to seasonality, local geomorphology, and distance from the point source (CSO #53), displaying a overall, linear response. However, the addition of nitrate and phosphate testing to the study revealed an entirely separate signal from that previously observed. Concentrations of these parameters did not respond to location in the same manner as E. coli. Instead of decreasing with distance from the CSO, a distinct periodicity was observed, correlating with a series of outflow pipes lining the stream banks. It is hypothesized that nitrate and phosphate occurring in this stretch of Scajaquada Creek originate not from the CSO, but from fertilizers used to maintain the lawns within the subwatershed. These results provide evidence of the complexity related to water quality issues in urban streams as a result of point- and nonpoint-source hydrologic inputs.

USE OF COMPOSITE DATA SETS FOR SOURCE-TRACKING ENTEROCCOCCI IN THE WATER COLUMN AND SHORELINE INTERSTITIAL WATERS ON PENSACOLA BEACH, FL

Science.gov (United States)

Genthner, Fred J., Joseph B. James, Diane F. Yates and Stephanie D. Friedman. Submitted. Use of Composite Data Sets for Source-Tracking Enterococci in the Water Column and Shoreline Interstitial Waters on Pensacola Beach Florida. Mar. Pollut. Bull. 33 p. (ERL,GB 1212). So...

Composition, nutritional aspects and effect on serum parameters of marine algae Ulva rigida.

Science.gov (United States)

Taboada, Cristina; Millán, Rosendo; Míguez, Isabel

2010-02-01

Algae are commonly consumed in Asia and have also gained popularity in Europe. However, data on the bioavailability of their components are limited. The present study was designed to determine the composition of Ulva rigida and the effects of inclusion of 10% of the algae in a standard diet for 4 weeks on nutritive value and serum parameters in order to consider the usefulness of Ulva as a dietary supplement. Ulva rigida is rich in protein, carbohydrates, fibre, vitamins and minerals and has a low lipid content. Analysis of the amino acid composition revealed good-quality protein. The algae were well accepted by experimental animals and did not significantly change nutritional parameters but reduced LDL cholesterol. Ulva rigida is an excellent source of nutrients and could improve a balanced diet. Further studies are required to research the potential of the seaweed as a natural source of bioactive compounds.

Origin, composition and quality of suspended particulate organic matter in relation to freshwater inflow in a South Texas estuary

Science.gov (United States)

Lebreton, Benoit; Beseres Pollack, Jennifer; Blomberg, Brittany; Palmer, Terence A.; Adams, Leslie; Guillou, Gaël; Montagna, Paul A.

2016-03-01

South Texas has a semi-arid climate with a large interannual variability of freshwater inflows. This study sought to define how changes in freshwater inflow affect the composition, quantity and quality of suspended particulate organic matter (SPOM) in a South Texas estuary: the Mission-Aransas estuary. The study was implemented 1.5 months after a large rain event in September 2010 and continued for 10 months of drought conditions. The composition of SPOM originating from rivers, the Gulf of Mexico and the estuary were determined using stable isotopes (δ13C, δ15N and δ34S). The quantity and quality of SPOM were assessed using organic carbon content, chlorophyll a concentrations and C/chl a ratios. Our results demonstrated that autochthonous phytoplankton was the dominant component of SPOM in the Mission-Aransas estuary during droughts. Benthic organic matter from local primary producers (i.e., seagrass, salt marsh plants, benthic microalgae) did not influence SPOM composition, either as fresh material or as detritus. A comparison with a positive estuary (i.e., Sabine-Neches estuary, TX) indicates that decreases in freshwater inflow may lead to decreases of terrestrial organic matter inputs and to increase the ratio of autochtonous phytoplanktonic material in SPOM.

Quality evaluation of cast Al-SiCp composites

International Nuclear Information System (INIS)

Adalarasu, S.; Mahadevan, S.; Satyanarayana, K.G.; Pai, B.C.; Pillai, R.M.

1996-01-01

This paper presents a methodology for using x-ray radiography and ultrasonic for testing the soundness and distribution of dispersoids and identifying the casting defects in a cast aluminium cast alloy matrix SiCp composites. The ultrasonic inspection could detect in 6061-SiCp cast composites 1) the presence of low levels of locked in stresses and 2) existence of local imperfection due to the combined effects of the local solidification condition and the presence of the dispersoids which were not possible through x-ray radiography. This clearly suggests that ultrasonic test can be used as a powerful NDE tool for screening the composite ingots. (author)

A framework for air quality monitoring based on free public data and open source tools

Science.gov (United States)

Nikolov, Hristo; Borisova, Denitsa

2014-10-01

In the recent years more and more widely accepted by the Space agencies (e.g. NASA, ESA) is the policy toward provision of Earth observation (EO) data and end products concerning air quality especially in large urban areas without cost to researchers and SMEs. Those EO data are complemented by increasing amount of in-situ data also provided at no cost either from national authorities or having crowdsourced origin. This accessibility together with the increased processing capabilities of the free and open source software is a prerequisite for creation of solid framework for air modeling in support of decision making at medium and large scale. Essential part of this framework is web-based GIS mapping tool responsible for dissemination of the output generated. In this research an attempt is made to establish a running framework based solely on openly accessible data on air quality and on set of freely available software tools for processing and modeling taking into account the present status quo in Bulgaria. Among the primary sources of data, especially for bigger urban areas, for different types of gases and dust particles, noted should be the National Institute of Meteorology and Hydrology of Bulgaria (NIMH) and National System for Environmental Monitoring managed by Bulgarian Executive Environmental Agency (ExEA). Both authorities provide data for concentration of several gases just to mention CO, CO2, NO2, SO2, and fine suspended dust (PM10, PM2.5) on monthly (for some data on daily) basis. In the framework proposed these data will complement the data from satellite-based sensors such as OMI instrument aboard EOS-Aura satellite and from TROPOMI instrument payload for future ESA Sentinel-5P mission. Integral part of the framework is the modern map for the land use/land cover which is provided from EEA by initiative GIO Land CORINE. This map is also a product from EO data distributed at European level. First and above all, our effort is focused on provision to the

NOAA's National Air Quality Predictions and Development of Aerosol and Atmospheric Composition Prediction Components for the Next Generation Global Prediction System

Science.gov (United States)

Stajner, I.; Hou, Y. T.; McQueen, J.; Lee, P.; Stein, A. F.; Tong, D.; Pan, L.; Huang, J.; Huang, H. C.; Upadhayay, S.

2016-12-01

NOAA provides operational air quality predictions using the National Air Quality Forecast Capability (NAQFC): ozone and wildfire smoke for the United States and airborne dust for the contiguous 48 states at http://airquality.weather.gov. NOAA's predictions of fine particulate matter (PM2.5) became publicly available in February 2016. Ozone and PM2.5 predictions are produced using a system that operationally links the Community Multiscale Air Quality (CMAQ) model with meteorological inputs from the North American mesoscale forecast Model (NAM). Smoke and dust predictions are provided using the Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model. Current NAQFC focus is on updating CMAQ to version 5.0.2, improving PM2.5 predictions, and updating emissions estimates, especially for NOx using recently observed trends. Wildfire smoke emissions from a newer version of the USFS BlueSky system are being included in a new configuration of the NAQFC NAM-CMAQ system, which is re-run for the previous 24 hours when the wildfires were observed from satellites, to better represent wildfire emissions prior to initiating predictions for the next 48 hours. In addition, NOAA is developing the Next Generation Global Prediction System (NGGPS) to represent the earth system for extended weather prediction. NGGPS will include a representation of atmospheric dynamics, physics, aerosols and atmospheric composition as well as coupling with ocean, wave, ice and land components. NGGPS is being developed with a broad community involvement, including community developed components and academic research to develop and test potential improvements for potentially inclusion in NGGPS. Several investigators at NOAA's research laboratories and in academia are working to improve the aerosol and gaseous chemistry representation for NGGPS, to develop and evaluate the representation of atmospheric composition, and to establish and improve the coupling with radiation and microphysics

Effects of marketing group and production focus on quality and variability of adipose tissue and bellies sourced from a commercial processing facility

Science.gov (United States)

Objectives were to determine the effects of marketing group on quality and variability of belly and adipose tissue quality traits of pigs sourced from differing production focuses (lean vs. quality). Pigs (N = 8,042) raised in 8 barns representing 2 seasons (cold and hot) were used. Three groups wer...

The Texas Air Quality Study: State of the Science of Ozone and Particulate Matter formation in Texas and Implications for Air Quality Policy

Science.gov (United States)

Allen, D. T.

2002-05-01

The Texas Air Quality Study (TexAQS) was performed during August and September of 2000; approximately 300 investigators from around the world made measurements of air pollutant concentrations and meteorological variables in southeast Texas. Five aircraft were deployed; five major ground chemistry sites were established and approximately 20 peripheral sites were established for collecting additional meteorological and chemical data. The scope, goals and preliminary results are available at the study web sites (www.utexas.edu/research/ceer/texaqs and www.utexas.edu/research/ceer/texaqsarchive). This presentation will provide an overview of the main findings from the study and will describe the role that ongoing data analysis activities are having on the development of air quality policy in the State of Texas. Some of the major findings are: Finding 1. Almost without exception, air parcels with very high ozone concentrations, observed by aircraft during the Texas Air Quality Study, had back trajectories that indicated a substantial contribution of emissions from industrial source regions. These air parcels also had chemical compositions that were representative of industrial sources, rather than typical urban sources. Finding 2: The rate of ozone production in and around the industrial source dominated areas in Houston can be very high, commonly exceeding 50 ppb/hr, and at times approaching instantaneous rates of 200 ppb/hr. Finding 3: The efficiency of ozone production in and around the industrial source dominated areas in Houston can be very high, ranging from 10-20 molecules of ozone per molecule of reacted NOx. Finding 4. Ozone production in the Houston urban plume was found to be slower and less efficient than in the composite industrial plume from the Ship Channel region and in plumes from isolated petrochemical facilities. Finding 5. The high rates and high efficiencies of ozone production in the industrial plumes are driven by high concentrations of reactive

Air quality impacted by local pollution sources and beyond - Using a prominent petro-industrial complex as a study case.

Science.gov (United States)

Chen, Sheng-Po; Wang, Chieh-Heng; Lin, Wen-Dian; Tong, Yu-Huei; Chen, Yu-Chun; Chiu, Ching-Jui; Chiang, Hung-Chi; Fan, Chen-Lun; Wang, Jia-Lin; Chang, Julius S

2018-05-01

The present study combines high-resolution measurements at various distances from a world-class gigantic petrochemical complex with model simulations to test a method to assess industrial emissions and their effect on local air quality. Due to the complexity in wind conditions which were highly seasonal, the dominant wind flow patterns in the coastal region of interest were classified into three types, namely northeast monsoonal (NEM) flows, southwest monsoonal (SEM) flows and local circulation (LC) based on six years of monitoring data. Sulfur dioxide (SO 2 ) was chosen as an indicative pollutant for prominent industrial emissions. A high-density monitoring network of 12 air-quality stations distributed within a 20-km radius surrounding the petrochemical complex provided hourly measurements of SO 2 and wind parameters. The SO 2 emissions from major industrial sources registered by the monitoring network were then used to validate model simulations and to illustrate the transport of the SO 2 plumes under the three typical wind patterns. It was found that the coupling of observations and modeling was able to successfully explain the transport of the industrial plumes. Although the petrochemical complex was seemingly the only major source to affect local air quality, multiple prominent sources from afar also played a significant role in local air quality. As a result, we found that a more complete and balanced assessment of the local air quality can be achieved only after taking into account the wind characteristics and emission factors of a much larger spatial scale than the initial (20 km by 20 km) study domain. Copyright © 2018 Elsevier Ltd. All rights reserved.

An introduction to data analysis of airborne particle composition

International Nuclear Information System (INIS)

Hopke, P.K.

1994-01-01

A major problem facing air quality management personnel is the identification of sources of airborne particles and the quantitative apportionment of the aerosol mass to those sources. The ability to collect particle samples and analyze these samples for a suite of elements by such techniques as neutron activation analysis or x-ray fluorescence provides that data for the problem of resolving a series of complex mixtures into its components based on the profiles of the elements emitted by the various sources in the airshed. If all of the sources and their composition profiles are known, then the mass balance model becomes a multiple regression problem. If a series of samples have been analyzed without substantial information being available on the sources, factor analysis methods can be employed. In both situations, there are limits to the identification of specific sources or the location of the sources. Thus, other methods that combine chemical with meteorological data have been developed to assist in spatial identification of pollutant sources. There are also limitations to the ability of any statistical method to resolve sources in real world problems. The physical and statistical basis of these methods and their application to representative problems are reviewed in this report. (author). 42 refs, 5 figs, 5 tabs

Pesticide residues in individual versus composite samples of apples after fine or coarse spray quality application

DEFF Research Database (Denmark)

Poulsen, Mette E.; Wenneker, Marcel; Withagen, Jacques

2012-01-01

. None of the results for the pesticides residues measured in individual apples exceeded the EU Maximum Residue Levels (MRLs). However, there was a large variation in the residues levels in the apples, with levels from 0.01 to 1.4 mg kg−1 for captan, the pesticide with the highest variation, and from 0.......01 to 0.2 mg kg−1 for pyraclostrobin, the pesticide with the lowest variation. Residues of fenoxycarb and indoxacarb were only found in a few apples, probably due to the early application time of these two compounds. The evaluation of the effect of spray quality did not show any major difference between......In this study, field trials on fine and coarse spray quality application of pesticides on apples were performed. The main objectives were to study the variation of pesticide residue levels in individual fruits versus composite samples, and the effect of standard fine spray quality application...

Lunch habits of German children and adolescents: composition and dietary quality.

Science.gov (United States)

Alexy, U; Freese, J; Kersting, M; Clausen, K

2013-01-01

Data from the ongoing, open-cohort Dortmund Nutritional and Anthropometric Longitudinally Designed (DONALD) study were used to describe warm family lunch meals and the association of the lunch composition with total diet quality. 2,095 three-day weighed dietary records, collected between 2004 and 2009, from a 4- to 18-year-old DONALD study subgroup were used. Warm lunch (eating occasions between 11.30 a.m. and 2.29 p.m. including at least one course that is typically consumed warm) was eaten on 68.8% of all record days. Meat lunch (>50%) was predominant, followed by vegetarian (25%), fish (13%) and sweet lunch meals (3%). The prevalence of desserts at lunch was high and beverages were drunk at 80% of lunch meals. A meat lunch was associated with a higher protein (+1.4% energy intake, %E) and fat intake (+1.7%E) than a sweet lunch; also densities of vitamin A, folate and iron were higher. A dessert at lunch decreased protein intake slightly (-0.2%E), but increased carbohydrate (+0.7%E) and added sugar intake (+1.4%E) as well as density of calcium (+18 mg/MJ). Our study proves the impact of lunch on daily dietary quality and yields valuable insights on the development of food and meal-based dietary guidelines. Copyright © 2012 S. Karger AG, Basel.

Belgrade waterworks groundwater source

International Nuclear Information System (INIS)

Sotic, A.; Dasic, M.; Vukcevic, G.; Vasiljevic, Lj.; Nikolic, S.

2002-01-01

Paper deals with Belgrade Waterworks groundwater source, its characteristics, conception of protection programme, contaminations on source and with parameters of groundwater quality degradation. Groundwaters present natural heritage with their strategic and slow renewable natural resources attributes, and as such they require priority in protection. It is of greatest need that existing source is to be protected and used optimally for producing quality drinkable water. The concept of source protection programme should be based on regular water quality monitoring, identification of contaminators, defining areas of their influences on the source and their permanent control. However, in the last 10 years, but drastically in the last 3, because of the overall situation in the country, it is very characteristic downfall in volume of business, organisation and the level of supply of the technical equipment

Late Cambrian - Early Ordovician turbidites of Gorny Altai (Russia): Compositions, sources, deposition settings, and tectonic implications

Science.gov (United States)

Kruk, Nikolai N.; Kuibida, Yana V.; Shokalsky, Sergey P.; Kiselev, Vladimir I.; Gusev, Nikolay I.

2018-06-01

The Cambrian-Ordovician transition was the time of several key events in the history of Central Asia. They were the accretion of Mariana-type island arc systems to the Siberian continent, the related large-scale orogeny and intrusions of basaltic and granitic magma and the formation of a huge turbidite basin commensurate with the Bengal Gulf basin in the western part of the Central Asian orogenic belt (CAOB). The structure of the basin, as well as the sources and environments of deposition remain open to discussion. This paper presents new major- and trace-element data on Late-Cambrian-Early Ordovician turbidites from different parts of the Russian Altai and a synthesis of Nd isotope composition and ages of detrital zircons. The turbidites share chemical similarity with material shed from weathered continental arcs. Broad variations of CIA (39-73) and ICV (0.63-1.66) signatures in sandstones suggest origin from diverse sources and absence of significant sorting. Trace elements vary considerably and have generally similar patterns in rocks from different terranes. On the other hand, there are at least two provinces according to Nd isotope composition and age of detrital zircons. Samples from eastern Russian Altai contain only Phanerozoic zircons and have Nd isotope ratios similar to those in Early Cambrian island arcs (εNdt + 4.4… + 5.4; TNd(DM)-2-st = 0.8-0.9 Ga). Samples from central, western, and southern parts of Russian Altai contain Precambrian zircons (some as old as Late Archean) and have a less radiogenic Nd composition (εNdt up to -3.6; TNd(DM)-2-st up to 1.5 Ga). The chemical signatures of Late Cambrian to Early Ordovician turbidites indicate a provenance chemically more mature than the island arc rocks, and the presence of zircons with 510-490 Ma ages disproves their genetic relation with island arcs. The turbidite basin formed simultaneously with peaks of granitic and alkali-basaltic magmatism in the western Central Asian orogen and resulted from

Metals in wine--impact on wine quality and health outcomes.

Science.gov (United States)

Tariba, Blanka

2011-12-01

Metals in wine can originate from both natural and anthropogenic sources, and its concentration can be a significant parameter affecting consumption and conservation of wine. Since metallic ions have important role in oxide-reductive reactions resulting in wine browning, turbidity, cloudiness, and astringency, wine quality depends greatly on its metal composition. Moreover, metals in wine may affect human health. Consumption of wine may contribute to the daily dietary intake of essential metals (i.e., copper, iron, and zinc) but can also have potentially toxic effects if metal concentrations are not kept under allowable limits. Therefore, a strict analytical control of metal concentration is required during the whole process of wine production. This article presents a critical review of the existing literature regarding the measured metal concentration in wine, methods applied for their determination, and possible sources, as well as their impact on wine quality and human health. The main focus is set on aluminum, arsenic, cadmium, chromium, copper, iron, manganese, nickel, lead, and zinc, as these elements most often affect wine quality and human health.

Fabrication of Nanocarbon Composites Using In Situ Chemical Vapor Deposition and Their Applications.

Science.gov (United States)

He, Chunnian; Zhao, Naiqin; Shi, Chunsheng; Liu, Enzuo; Li, Jiajun

2015-09-23

Nanocarbon (carbon nanotubes (CNTs) and graphene (GN)) composites attract considerable research interest due to their fascinating applications in many fields. Here, recent developments in the field of in situ chemical vapor deposition (CVD) for the design and controlled preparation of advanced nanocarbon composites are highlighted, specifically, CNT-reinforced bulk structural composites, as well as CNT, GN, and CNT/GN functional composites, together with their practical and potential applications. In situ CVD is a very attractive approach for the fabrication of composites because of its engaging features, such as its simplicity, low-cost, versatility, and tunability. The morphologies, structures, dispersion, and interface of the resulting nanocarbon composites can be easily modulated by varying the experimental parameters (such as temperature, catalysts, carbon sources, templates or template catalysts, etc.), which enables a great potential for the in situ synthesis of high-quality nanocarbons with tailored size and dimension for constructing high-performance composites, which has not yet been achieved by conventional methods. In addition, new trends of the in situ CVD toward nanocarbon composites are discussed. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Sources of Variation in the Age Composition of Sandeel Landings

DEFF Research Database (Denmark)

Kvist, Trine; Gislason, Hannes; Thyregod, Poul

2001-01-01

in the samples is significantly lower in the start and end of the fishing season. This suggests that the older sandeel are available to the fishery for a shorter time period that the 1-group. Significant differences are found in the age composition between the four laboratories involved in the age determination......The variation of the age composition of the landings of lesser sandeel in the Danish industrial fishery in the North Sea over the period From 1984-1993 is analysed by continuation-ratio logits and generalised linear models. The analysis takes the multinomial characteristics of the age composition....... Although the variation between ICES statistical rectangles is substantial there is a significant difference between the age composition in the northern and southern part of the North Sea. However, only one of the three finer geographical stratifications proposed to improve the assessment results...

Growth kinetics and properties of ZnO/ZnMgO heterostructures grown by radical-source molecular beam epitaxy

Energy Technology Data Exchange (ETDEWEB)

Ivanov, S.V. [Institute of Semiconductor Technology, Technical University Braunschweig, Hans-Sommer-Str. 66, 38106 Braunschweig (Germany); Ioffe Physico-Technical Institute, Polytekhnicheskaya Street 26, 194021 St. Petersburg (Russian Federation); El-Shaer, A.; Bakin, A.; Waag, A. [Institute of Semiconductor Technology, Technical University Braunschweig, Hans-Sommer-Str. 66, 38106 Braunschweig (Germany); Shubina, T.V.; Listoshin, S.B. [Ioffe Physico-Technical Institute, Polytekhnicheskaya Street 26, 194021 St. Petersburg (Russian Federation)

2007-07-01

A phenomenological approach to quantitative description of Zn(Mg)O growth by radical-source molecular beam epitaxy, based on the experimental studies of RHEED intensity oscillations, has been developed. It allows a precise control of growth rate, composition and stoichiometry at any growth temperature, Along with optimization of a growth initiation procedure on a c-sapphire, it is necessary condition for fabrication of high quality ZnO epilayers and ZnO/ZnMgO heterostructures in a wide Mg composition range. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Lead Isotope Compositions of Acid Residues from Olivine-Phyric Shergottite Tissint: Implications for Heterogeneous Shergottite Source Reservoirs

Science.gov (United States)

Moriwaki, R.; Usui, T.; Yokoyama, T.; Simon, J. I.; Jones, J. H.

2015-01-01

Geochemical studies of shergottites suggest that their parental magmas reflect mixtures between at least two distinct geochemical source reservoirs, producing correlations between radiogenic isotope compositions and trace element abundances. These correlations have been interpreted as indicating the presence of a reduced, incompatible element- depleted reservoir and an oxidized, incompatible- element-enriched reservoir. The former is clearly a depleted mantle source, but there is ongoing debate regarding the origin of the enriched reservoir. Two contrasting models have been proposed regarding the location and mixing process of the two geochemical source reservoirs: (1) assimilation of oxidized crust by mantle derived, reduced magmas, or (2) mixing of two distinct mantle reservoirs during melting. The former requires the ancient Martian crust to be the enriched source (crustal assimilation), whereas the latter requires isolation of a long-lived enriched mantle domain that probably originated from residual melts formed during solidification of a magma ocean (heterogeneous mantle model). This study conducts Pb isotope and trace element concentration analyses of sequential acid-leaching fractions (leachates and the final residues) from the geochemically depleted olivine-phyric shergottite Tissint. The results suggest that the Tissint magma is not isotopically uniform and sampled at least two geochemical source reservoirs, implying that either crustal assimilation or magma mixing would have played a role in the Tissint petrogenesis.

The composition of readily available carbon sources produced by fermentation of fish faeces is affected by dietary protein:energy ratios

DEFF Research Database (Denmark)

Letelier-Gordo, Carlos Octavio; Larsen, Bodil Katrine; Dalsgaard, Johanne

2017-01-01

, 17, 19, 21 and 23 g/MJ) to rainbow trout (Oncorhynchus mykiss) on the production of volatile fatty acids (VFAs) and ethanol during 7 days fermentation of the produced fish faeces. The total yields of VFAs and ethanol obtained (expressed as chemical oxygen demand (COD)) ranged between 0.21–0.24 g...... of acetic and valeric acid. Changing the diet composition thus affects the composition of readily available carbon that can be derived from the faeces. This can be applied to enhance on-farm single sludge denitrification and reduce the need for adding external carbon sources such as e.g. methanol....

Energy recovery during expansion of compressed gas using power plant low-quality heat sources

Science.gov (United States)

Ochs, Thomas L [Albany, OR; O'Connor, William K [Lebanon, OR

2006-03-07

A method of recovering energy from a cool compressed gas, compressed liquid, vapor, or supercritical fluid is disclosed which includes incrementally expanding the compressed gas, compressed liquid, vapor, or supercritical fluid through a plurality of expansion engines and heating the gas, vapor, compressed liquid, or supercritical fluid entering at least one of the expansion engines with a low quality heat source. Expansion engines such as turbines and multiple expansions with heating are disclosed.

The Genetics of Pork Quality

NARCIS (Netherlands)

Wijk, van H.J.

2006-01-01

This thesis describes the genetics of carcass composition and pork quality traits. A large population of commercial finishers was extensively phenotyped for growth, carcass composition and meat quality traits. Genetic parameters were estimated based on those measurements. The population was

Application of water quality index for the assessment of suitability of natural sources of water for drinking in rural areas of east Sikkim, India

OpenAIRE

Shubra Poonia; T Shantikumar Singh; Dechen C Tsering

2015-01-01

In Sikkim, especially in the rural areas where there is no supply of treated water for drinking and other domestic uses, natural surface water is the only source. The objective was to assess the water quality of natural sources of water in the rural areas of East Sikkim using a water quality index (WQI) for different seasons. A total of 225 samples, that is, 75 in winter, 75 in summer, and 75 in monsoon were collected from different sources for physicochemical analysis, and a WQI was calculat...

Effects of free-range access on production parameters and meat quality, composition and taste in slow-growing broiler chickens.

Science.gov (United States)

Stadig, Lisanne M; Rodenburg, T Bas; Reubens, Bert; Aerts, Johan; Duquenne, Barbara; Tuyttens, Frank A M

2016-12-01

Demand for meat from free-range broiler chickens is increasing in several countries. Consumers are motivated by better animal welfare and other product attributes such as quality and taste. However, scientific literature is not unanimous about whether free-range access influences quality, composition, and taste of the meat. Because chickens normally do not use free-range areas optimally, it is possible that provision of more suitable shelter will lead to more pronounced differences between chickens raised indoors and outdoors. In this study, an experiment with 2 production rounds of 600 slow-growing broilers each was performed. In each round, 200 chickens were raised indoors (IN), 200 had free-range access to grassland with artificial shelter (AS), and 200 had free-range access to short-rotation coppice with willow (SRC). Free-range use, feed intake, and growth were monitored, and after slaughter (d72) meat quality, composition, and taste were assessed. Free-range use was higher in SRC than in AS chickens (42.8 vs. 35.1%, P free-range access was darker (P = 0.021) and yellower (P = 0.001) than that of IN chickens. Ultimate pH was lower (5.73 vs. 5.79; P = 0.006) and drip loss higher (1.29 vs. 1.09%; P = 0.05) in IN versus AS chickens. The percentage of polyunsaturated fatty acids was higher in AS than in IN meat (35.84 vs. 34.59%; P = 0.021). The taste panel judged breast meat of SRC chickens to be more tender (P = 0.003) and less fibrous (P = 0.013) compared to that of AS and IN chickens, and juicier compared to the IN chickens (P = 0.017). Overall, free-range access negatively affected slaughter weight, but positively affected meat quality, taste, and composition. Only a few differences between AS and SRC were found, possibly due to limited differences in free-range use. © 2016 Poultry Science Association Inc.

Aerosol composition and source apportionment in the Mexico City Metropolitan Area with PIXE/PESA/STIM and multivariate analysis

OpenAIRE

Johnson , K. S.; De Foy , B.; Zuberi , B.; Molina , L. T.; Molina , M. J.; Xie , Y.; Laskin , A.; Shutthanandan , V.

2006-01-01

Aerosols play an important role in the atmosphere but are poorly characterized, particularly in urban areas like the Mexico City Metropolitan Area (MCMA). The chemical composition of urban particles must be known to assess their effects on the environment, and specific particulate emissions sources should be identified to establish effective pollution control standards. For these reasons, samples of particulate matter ≤2.5 μm (PM_2.5) were collected dur...

Effect of crushing temperature on virgin olive oil quality and composition

Directory of Open Access Journals (Sweden)

Ö. Kula

2018-03-01

Full Text Available The objective of the current study was to assess the influence of a modified crushing process and kneading operation on the quality parameters, volatile compounds, and the fatty acid and sterol profiles of virgin olive oil from the Edremit yaglik variety. In the study, olive oil samples were produced in two different processes. The first one was produced without malaxation and the second one was produced with the malaxing process. During crushing, the effect of different temperatures was tested. The results demonstrate that different crushing temperatures generally did not affect the amount of free fatty acids, or peroxide value. Total phenol contents were positively affected by the additional malaxation process. Fatty acids and sterol composition were not significantly altered at different crushing temperatures or during the subsequent malaxation application. PCA enabled a clear classification of the oils obtained from different processing techniques.

Annatto seed residue (Bixa orellana L.: nutritional quality

Directory of Open Access Journals (Sweden)

Melissa Alessandra Valério

2015-06-01

Full Text Available Considering that annatto seeds are rich in protein, the present work aimed to evaluate the biological quality of this nutrient in the meal residue originating from annatto seed processing. We determined the general composition, mineral levels, amino acid composition and chemical scores, antinutritional factors, and protein quality using biological assays. The following values were obtained: 11.50% protein, 6.74% moisture, 5.22% ash, 2.22% lipids, 42.19% total carbohydrates and 28.45% fiber. The residue proved to be a food rich in fiber and also a protein source. Antinutritional factors were not detected. The most abundant amino acids were lysine, phenylalanine + tyrosine, leucine and isoleucine. Valine was the most limiting amino acid (chemical score 0.22. The protein quality of the seed residue and the isolated protein showed no significant differences. The biological value was lower than that of the control protein but higher than that found in other vegetables. Among the biochemical analyses, only creatinine level was decreased in the two test groups compared to the control group. Enzyme tests did not indicate liver toxicity. The results showed favorable aspects for the use of annatto seed residue in the human diet, meriting further research.

Analysis of point source pollution and water environmental quality variation trends in the Nansi Lake basin from 2002 to 2012.

Science.gov (United States)

Wang, Weiliang; Liu, Xiaohui; Wang, Yufan; Guo, Xiaochun; Lu, Shaoyong

2016-03-01

Based on the data analysis of the water environmental quality and economic development from 2002 to 2012 in the Nansi Lake basin, the correlation and change between the water environmental quality and economic development were studied. Results showed that the GDP and wastewater emissions of point source in the Nansi Lake basin had an average annual growth of 7.30 and 7.68 %, respectively, from 2002 to 2012. The emissions of chemical oxygen demand (COD) and ammonia nitrogen (NH3-N) had the average annual decrease of 7.69 and 6.79 % in 2012, respectively, compared to 2002. Basin water quality overall improved, reaching the Class III of the "Environmental quality standards for surface water (GB3838-2002)," in which the main reason was that sewage treatment rate increased gradually and was above 90 % in 2012 (an increase of 10 % compared to 2002) with the progress of pollution abatement technology and the implementation of relevant policies and regulations. The contribution of water environmental pollution was analyzed from related cities (Ji'ning, Zaozhuang, Heze). Results indicated that Ji'ning had the largest contribution to water pollution of the Nansi Lake basin, and the pollutant from domestic sources accounted for a higher percentage compared to industrial sources. The wastewater, COD, and NH3-N mainly came from mining and washing of coal, manufacture of raw chemical materials and chemical products, papermaking industry, and food processing industry. According to the water pollution characteristics of the Nansi Lake basin, the basin pollution treatment strategy and prevention and treatment system were dissected to provide a scientific basis for prevention and control of lakeside point source pollution along the Nansi Lake.

Diagnosis of pulmonary artery embolism. Comparison of single-source CT and 3rd generation dual-source CT using a dual-energy protocol regarding image quality and radiation dose

International Nuclear Information System (INIS)

Petritsch, Bernhard; Kosmala, Aleksander; Gassenmeier, Tobias; Weng, Andreas Max; Veldhoen, Simon; Kunz, Andreas Steven; Bley, Thorsten Alexander

2017-01-01

To compare radiation dose, subjective and objective image quality of 3 rd generation dual-source CT (DSCT) and dual-energy CT (DECT) with conventional 64-slice single-source CT (SSCT) for pulmonary CTA. 180 pulmonary CTA studies were performed in three patient cohorts of 60 patients each. Group 1: conventional SSCT 120 kV (ref.); group 2: single-energy DSCT 100 kV (ref.); group 3: DECT 90/Sn150 kV. CTDIvol, DLP, effective radiation dose were reported, and CT attenuation (HU) was measured on three central and peripheral levels. The signal-to-noise-ratio (SNR) and contrast-to-noise-ratio (CNR) were calculated. Two readers assessed subjective image quality according to a five-point scale. Mean CTDIvol and DLP were significantly lower in the dual-energy group compared to the SSCT group (p < 0.001 [CTDIvol]; p < 0.001 [DLP]) and the DSCT group (p = 0.003 [CTDIvol]; p = 0.003 [DLP]), respectively. The effective dose in the DECT group was 2.79 ± 0.95 mSv and significantly smaller than in the SSCT group (4.60 ± 1.68 mSv, p < 0.001) and the DSCT group (4.24 ± 2.69 mSv, p = 0.003). The SNR and CNR were significantly higher in the DSCT group (p < 0.001). Subjective image quality did not differ significantly among the three protocols and was rated good to excellent in 75 % (135/180) of cases with an inter-observer agreement of 80 %. Dual-energy pulmonary CTA protocols of 3 rd generation dual-source scanners allow for significant reduction of radiation dose while providing excellent image quality and potential additional information by means of perfusion maps. Dual-energy CT with 90/Sn150 kV configuration allows for significant dose reduction in pulmonary CTA. Subjective image quality was similar among the three evaluated CT-protocols (64-slice SSCT, single-energy DSCT, 90/Sn150 kV DECT) and was rated good to excellent in 75% of cases. Dual-energy CT provides potential additional information by means of iodine distribution maps.

Improvement of electrolaryngeal speech quality using a supraglottal voice source with compensation of vocal tract characteristics.

Science.gov (United States)

Wu, Liang; Wan, Congying; Wang, Supin; Wan, Mingxi

2013-07-01

Electrolarynx (EL) is a medical speech-recovery device designed for patients who have lost their original voice box due to laryngeal cancer. As a substitute for human larynx, the current commercial EL voice source cannot reconstruct natural EL speech under laryngectomy conditions. To eliminate the abnormal acoustic properties of EL speech, a supraglottal voice source with compensation of vocal tract characteristics was proposed and provided through an experimental EL(SGVS-EL) system. The acoustic analyses of simulated EL speech and reconstructed EL speech produced with different voice sources were performed in the normal subject and laryngectomee. The results indicated that the supraglottal voice source was successful in improving the acoustic properties of EL speech by enhancing low- frequency energy, correcting the shifted formants to normal range, and eliminating the visible spectral zeros. Both normal subject and laryngectomee also produced more natural vowels using SGVS-EL than commercial EL, even if the vocal tract parameter was substituted and the supraglottal voice source was biased to a certain degree. Therefore, supraglottal voice source is a feasible and effective approach to improving the acoustic quality of EL speech.

Atmospheric aerosol compositions and sources at two national background sites in northern and southern China

Directory of Open Access Journals (Sweden)

Q. Zhu

2016-08-01

Full Text Available Although China's severe air pollution has become a focus in the field of atmospheric chemistry and the mechanisms of urban air pollution there have been researched extensively, few field sampling campaigns have been conducted at remote background sites in China, where air pollution characteristics on a larger scale are highlighted. In this study, an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS, together with an Aethalometer, was deployed at two of China's national background sites in northern (Lake Hongze site; 33.23° N, 118.33° E; altitude 21 m and southern (Mount Wuzhi site; 18.84° N, 109.49° E; altitude 958 m China in the spring seasons in 2011 and 2015, respectively, in order to characterize submicron aerosol composition and sources. The campaign-average PM1 concentration was 36.8 ± 19.8 µg m−3 at the northern China background (NCB site, which was far higher than that at the southern China background (SCB site (10.9 ± 7.8 µg m−3. Organic aerosol (OA (27.2 %, nitrate (26.7 %, and sulfate (22.0 % contributed the most to the PM1 mass at NCB, while OA (43.5 % and sulfate (30.5 % were the most abundant components of the PM1 mass at SCB, where nitrate only constituted a small fraction (4.7 % and might have contained a significant amount of organic nitrates (5–11 %. The aerosol size distributions and organic aerosol elemental compositions all indicated very aged aerosol particles at both sites. The OA at SCB was more oxidized with a higher average oxygen to carbon (O ∕ C ratio (0.98 than that at NCB (0.67. Positive matrix factorization (PMF analysis was used to classify OA into three components, including a hydrocarbon-like component (HOA, attributed to fossil fuel combustion and two oxygenated components (OOA1 and OOA2, attributed to secondary organic aerosols from different source areas at NCB. PMF analysis at SCB identified a semi-volatile oxygenated

Relationship between fatty acid composition and biodiesel quality for nine commercial palm oils

Directory of Open Access Journals (Sweden)

Chanida Lamaisri

2015-08-01

Full Text Available Biodiesel is an alternative fuel consisting of alkyl esters of fatty acids from vegetable oils or animal fats. The fatty acid compositions in the oils used as feedstock can influence quality of the biodiesel. In the present study, oil content and fatty acid composition of mesocarp and kernel oil were examined from nine commercial oil palm Elaeis guineensis cultivars. Saponification number, iodine value and cetane number were calculated from palm oil fatty acid methyl ester compositions. Fruits of tenera oil palm were collected from a farmer’s plantation in Dan Makham Tia District, Kanchanaburi Province in 2009. Variation between cultivars was observed in oil content and fatty acid profile of mesocarp oil rather than kernel oil. The percentage of oil in dry mesocarp ranged from 63.8% to 74.9%. The mesocarp oil composed of 41.5 - 51.6% palmitic acid, 3.58-7.10% stearic acid, 32.8-42.5% oleic acid and 9.3-13.0% linoleic acid. Likewise saponification number, iodine value and cetane number of mesocarp oil fatty acid methyl ester showed more variation among cultivars, ranging from 196.5-198.9, 45.7-54.6 and 61.8-63.6, respectively. While those of kernel oil fatty acid methyl ester showed no different among cultivars, ranging from 229-242, 13.6-16.4 and 65.3-66.5, respectively. The cetane number of fatty acid methyl ester positively correlated with contents of myristic, palmitic and stearic acids in palm oil and saponification number of biodiesel, but negatively correlated with iodine value

Source apportionment of PM2.5 at multiple Northwest U.S. sites: Assessing regional winter wood smoke impacts from residential wood combustion

Science.gov (United States)

Kotchenruther, Robert A.

2016-10-01

Wood smoke from residential wood combustion is a significant source of elevated PM2.5 in many communities across the Northwest U.S. Accurate representation of residential wood combustion in source-oriented regional scale air quality models is challenging because of multiple uncertainties. As an alternative to source-oriented source apportionment, this work provides, through receptor-oriented source apportionment, an assessment of winter residential wood combustion impacts at multiple Northwest U.S. locations. Source apportionment was performed on chemically speciated PM2.5 from 19 monitoring sites using the Positive Matrix Factorization (PMF) receptor model. Each site was modeled independently, but a common data preparation and modeling protocol was used so that results were as comparable as possible across sites. Model solutions had from 4 to 8 PMF factors, depending on the site. PMF factors at each site were associated with a source classification (e.g., primary wood smoke), a dominant chemical composition (e.g., ammonium nitrate), or were some mixture. 15 different sources or chemical compositions were identified as contributing to PM2.5 across the 19 sites. The 6 most common were; aged wood smoke and secondary organic carbon, motor vehicles, primary wood smoke, ammonium nitrate, ammonium sulfate, and fugitive dust. Wood smoke was identified at every site, with both aged and primary wood smoke identified at most sites. Wood smoke contributions to PM2.5 were averaged for the two winter months of December and January, the months when wood smoke in the Northwest U.S. is mainly from residential wood combustion. The total contribution of residential wood combustion, that from primary plus aged smoke, ranged from 11.4% to 92.7% of average December and January PM2.5 depending on the site, with the highest percent contributions occurring in smaller towns that have fewer expected sources of winter PM2.5. Receptor modeling at multiple sites, such as that conducted in this

Chemometric expertise of the quality of groundwater sources for domestic use.

Science.gov (United States)

Spanos, Thomas; Ene, Antoaneta; Simeonova, Pavlina

2015-01-01

In the present study 49 representative sites have been selected for the collection of water samples from central water supplies with different geographical locations in the region of Kavala, Northern Greece. Ten physicochemical parameters (pH, electric conductivity, nitrate, chloride, sodium, potassium, total alkalinity, total hardness, bicarbonate and calcium) were analyzed monthly, in the period from January 2010 to December 2010. Chemometric methods were used for monitoring data mining and interpretation (cluster analysis, principal components analysis and source apportioning by principal components regression). The clustering of the chemical indicators delivers two major clusters related to the water hardness and the mineral components (impacted by sea, bedrock and acidity factors). The sampling locations are separated into three major clusters corresponding to the spatial distribution of the sites - coastal, lowland and semi-mountainous. The principal components analysis reveals two latent factors responsible for the data structures, which are also an indication for the sources determining the groundwater quality of the region (conditionally named "mineral" factor and "water hardness" factor). By the apportionment approach it is shown what the contribution is of each of the identified sources to the formation of the total concentration of each one of the chemical parameters. The mean values of the studied physicochemical parameters were found to be within the limits given in the 98/83/EC Directive. The water samples are appropriate for human consumption. The results of this study provide an overview of the hydrogeological profile of water supply system for the studied area.

A brief discussion about image quality and SEM methods for quantitative fractography of polymer composites.

Science.gov (United States)

Hein, L R O; Campos, K A; Caltabiano, P C R O; Kostov, K G

2013-01-01

The methodology for fracture analysis of polymeric composites with scanning electron microscopes (SEM) is still under discussion. Many authors prefer to use sputter coating with a conductive material instead of applying low-voltage (LV) or variable-pressure (VP) methods, which preserves the original surfaces. The present work examines the effects of sputter coating with 25 nm of gold on the topography of carbon-epoxy composites fracture surfaces, using an atomic force microscope. Also, the influence of SEM imaging parameters on fractal measurements is evaluated for the VP-SEM and LV-SEM methods. It was observed that topographic measurements were not significantly affected by the gold coating at tested scale. Moreover, changes on SEM setup leads to nonlinear outcome on texture parameters, such as fractal dimension and entropy values. For VP-SEM or LV-SEM, fractal dimension and entropy values did not present any evident relation with image quality parameters, but the resolution must be optimized with imaging setup, accompanied by charge neutralization. © Wiley Periodicals, Inc.

Factors affecting quality for beta dose rate measurements using ISO 6980 series I reference sources

Energy Technology Data Exchange (ETDEWEB)

Burns, R.E. Jr.; O`Brien, J.M. Jr. [Atlan-Tech, Rosewll, GA (United States)

1993-12-31

Atlan-Tech, Inc. has performed several calibrations of ISO 6980 Series 1 reference beta sources over the past two to three years. There were many problems encountered in attempting to compare the results of these calibrations with those from other laboratories, indicating the need for more standardization in the methodology employed for the measurement of the absorbed dose rate from ISO 6980 Series 1 reference beta sources. This document describes some of the problems encountered in attempting to intercompare results of beta dose-rate measurements. It proposes some solutions in an attempt to open a dialogue among facilities using reference beta standards for the purpose of promoting better measurement quality assurance through data intercomparison.

Factors affecting quality for beta dose rate measurements using ISO 6980 series I reference sources

International Nuclear Information System (INIS)

Burns, R.E. Jr.; O'Brien, J.M. Jr.

1993-01-01

Atlan-Tech, Inc. has performed several calibrations of ISO 6980 Series 1 reference beta sources over the past two to three years. There were many problems encountered in attempting to compare the results of these calibrations with those from other laboratories, indicating the need for more standardization in the methodology employed for the measurement of the absorbed dose rate from ISO 6980 Series 1 reference beta sources. This document describes some of the problems encountered in attempting to intercompare results of beta dose-rate measurements. It proposes some solutions in an attempt to open a dialogue among facilities using reference beta standards for the purpose of promoting better measurement quality assurance through data intercomparison

Critical Quality Source Diagnosis for Dam Concrete Construction Based on Quality Gain-loss Function

Directory of Open Access Journals (Sweden)

Bo Wang

2014-06-01

Full Text Available In dam concrete construction process, it not only has quality loss arising from quality fluctuation, but also gains quality compensation effect due to the mutual cooperation and adaptation coupling between working procedures (WPs. The calculation and transmission complexity of the quality loss and quality compensation affect the quality management of dam concrete construction. As the quality compensation effect existing in the production practice cannot be described by Taguchi quality loss function, the concept of quality gain-loss function was presented in this paper, which was based on endowing the constant term in the expansion of Taylor series with physical meaning—quality compensation. Based on quality gain-loss function theory, a new quality gain-loss transmission model of dam concrete construction based on GERT network was constructed and its effective algorithm was designed. WP quality gain-loss and its impact on the final product were reasonably measured, and the critical quality routes and critical quality WPs were detected and diagnosed in dam concrete construction network. Summer temperature-controlled concrete construction in the third phase of Three Gorges Project (TGP was taken as an example to carry out the study, and the calculation results showed the validity and practicability of the presented model and algorithm.

Fine-grained suspended sediment source identification for the Kharaa River basin, northern Mongolia

Science.gov (United States)

Rode, Michael; Theuring, Philipp; Collins, Adrian L.

2015-04-01

Fine sediment inputs into river systems can be a major source of nutrients and heavy metals and have a strong impact on the water quality and ecosystem functions of rivers and lakes, including those in semiarid regions. However, little is known to date about the spatial distribution of sediment sources in most large scale river basins in Central Asia. Accordingly, a sediment source fingerprinting technique was used to assess the spatial sources of fine-grained (source discrimination with geochemical composite fingerprints based on a new Genetic Algorithm (GA)-driven Discriminant Function Analysis, the Kruskal-Wallis H-test and Principal Component Analysis. The composite fingerprints were subsequently used for numerical mass balance modelling with uncertainty analysis. The contributions of the individual sub-catchment spatial sediment sources varied from 6.4% (the headwater sub-catchment of Sugnugur Gol) to 36.2% (the Kharaa II sub-catchment in the middle reaches of the study basin) with the pattern generally showing higher contributions from the sub-catchments in the middle, rather than the upstream, portions of the study area. The importance of riverbank erosion was shown to increase from upstream to midstream tributaries. The source tracing procedure provides results in reasonable accordance with previous findings in the study region and demonstrates the general applicability and associated uncertainties of an approach for fine-grained sediment source investigation in large scale semi-arid catchments. The combined application of source fingerprinting and catchment modelling approaches can be used to assess whether tracing estimates are credible and in combination such approaches provide a basis for making sediment source apportionment more compelling to catchment stakeholders and managers.

Chemical composition, sources and secondary processes of aerosols in Baoji city of northwest China

Science.gov (United States)

Wang, Y. C.; Huang, R.-J.; Ni, H. Y.; Chen, Y.; Wang, Q. Y.; Li, G. H.; Tie, X. X.; Shen, Z. X.; Huang, Y.; Liu, S. X.; Dong, W. M.; Xue, P.; Fröhlich, R.; Canonaco, F.; Elser, M.; Daellenbach, K. R.; Bozzetti, C.; El Haddad, I.; Prévôt, A. S. H.; Canagaratna, M. R.; Worsnop, D. R.; Cao, J. J.

2017-06-01

Particulate air pollution is a severe environmental problem in China, affecting visibility, air quality, climate and human health. However, previous studies focus mainly on large cities such as Beijing, Shanghai, and Guangzhou. In this study, an Aerodyne Aerosol Chemical Speciation Monitor was deployed in Baoji, a middle size inland city in northwest China from 26 February to 27 March 2014. The non-refractory submicron aerosol (NR-PM1) was dominated by organics (55%), followed by sulfate (16%), nitrate (15%), ammonium (11%) and chloride (3%). A source apportionment of the organic aerosol (OA) was performed with the Sofi (Source Finder) interface of ME-2 (Multilinear Engine), and six main sources/factors were identified and classified as hydrocarbon-like OA (HOA), cooking OA (COA), biomass burning OA (BBOA), coal combustion OA (CCOA), less oxidized oxygenated OA (LO-OOA) and more oxidized oxygenated OA (MO-OOA), which contributed 20%, 14%, 13%, 9%, 23% and 21% of total OA, respectively. The contribution of secondary components shows increasing trends from clean days to polluted days, indicating the importance of secondary aerosol formation processes in driving particulate air pollution. The formation of LO-OOA and MO-OOA is mainly driven by photochemical reactions, but significantly influenced by aqueous-phase chemistry during periods of low atmospheric oxidative capacity.

Chemical composition and sources of particle pollution in affluent and poor neighborhoods of Accra, Ghana

International Nuclear Information System (INIS)

Zhou, Zheng; Dionisio, Kathie L; Verissimo, Thiago G; Kerr, Americo S; Coull, Brent; Arku, Raphael E; Koutrakis, Petros; Spengler, John D; Vallarino, Jose; Hughes, Allison F; Agyei-Mensah, Samuel; Ezzati, Majid

2013-01-01

The highest levels of air pollution in the world now occur in developing country cities, where air pollution sources differ from high-income countries. We analyzed particulate matter (PM) chemical composition and estimated the contributions of various sources to particle pollution in poor and affluent neighborhoods of Accra, Ghana. Elements from earth’s crust were most abundant during the seasonal Harmattan period between late December and late January when Saharan dust is carried to coastal West Africa. During Harmattan, crustal particles accounted for 55 μg m −3 (37%) of fine particle (PM 2.5 ) mass and 128 μg m −3 (42%) of PM 10 mass. Outside Harmattan, biomass combustion, which was associated with higher black carbon, potassium, and sulfur, accounted for between 10.6 and 21.3 μg m −3 of fine particle mass in different neighborhoods, with its contribution largest in the poorest neighborhood. Other sources were sea salt, vehicle emissions, tire and brake wear, road dust, and solid waste burning. Reducing air pollution in African cities requires policies related to energy, transportation and urban planning, and forestry and agriculture, with explicit attention to impacts of each strategy in poor communities. Such cross-sectoral integration requires emphasis on urban environment and urban poverty in the post-2015 Development Agenda. (letter)

Change of the Asian dust source region deduced from the composition of anthropogenic radionuclides in surface soil in Mongolia

Directory of Open Access Journals (Sweden)

Y. Igarashi

2011-07-01

Full Text Available Recent climate change, especially during the 2000s, may be the primary reason for the expansion of the Asian dust source region. The change in the dust source region was investigated by examining anthropogenic radionuclides contained in surface soil samples from Mongolia. Surface soil was globally labeled by radioactive fallout from nuclear testing during the late 1950s and early 1960s, but there are no current direct sources for anthropogenic radionuclides in the air (before the Fukushima nuclear power plant accident in 2011. Radionuclides in the atmosphere are therefore carried mainly by wind-blown dust from surface soil, that is, aeolian dust. Asian dust carries traces of ⁹⁰Sr, ¹³⁷Cs, and other anthropogenic radionuclides; the heaviest deposition occurs in spring and has been recorded in Japan since the early 1990s. The composition of anthropogenic radionuclides in atmospheric depositions would be affected by a change in the dust source. Previous studies of atmospheric deposition at long-term monitoring sites (e.g. in Tsukuba, Japan have detected changes in the ¹³⁷Cs/⁹⁰Sr ratio and in the specific activity of the radionuclides. These changes in the composition of observed atmospheric depositions are supposed to reflect changes in the climatic conditions of the dust source region. To investigate this dust source change, we conducted a field survey of radionuclides (⁹⁰Sr and ¹³⁷Cs in surface soil samples in September 2007 in the eastern and southern regions of Mongolia, where dust storms have occurred more frequently since 2000. The specific activities of both radionuclides as well as the ¹³⁷Cs/⁹⁰Sr ratio in the surface soil were well correlated with annual average precipitation in the Mongolian desert-steppe zone. Higher specific activities and a higher ¹³⁷Cs/⁹⁰Sr ratio were found in grassland regions that experienced greater

Aerosol composition and source apportionment in the Mexico City Metropolitan Area with PIXE/PESA/STIM and multivariate analysis

OpenAIRE

K. S. Johnson; B. de Foy; B. de Foy; B. Zuberi; B. Zuberi; L. T. Molina; L. T. Molina; M. J. Molina; M. J. Molina; Y. Xie; A. Laskin; V. Shutthanandan

2006-01-01

Aerosols play an important role in the atmosphere but are poorly characterized, particularly in urban areas like the Mexico City Metropolitan Area (MCMA). The chemical composition of urban particles must be known to assess their effects on the environment, and specific particulate emissions sources should be identified to establish effective pollution control standards. For these reasons, samples of particulate matter ≤2.5 μm (PM2.5) were collected during the MCMA-2003 Field Campaign f...

Source apportionment of aerosol particles at a European air pollution hot spot using particle number size distributions and chemical composition.

Science.gov (United States)

Leoni, Cecilia; Pokorná, Petra; Hovorka, Jan; Masiol, Mauro; Topinka, Jan; Zhao, Yongjing; Křůmal, Kamil; Cliff, Steven; Mikuška, Pavel; Hopke, Philip K

2018-03-01

Ostrava in the Moravian-Silesian region (Czech Republic) is a European air pollution hot spot for airborne particulate matter (PM), polycyclic aromatic hydrocarbons (PAHs), and ultrafine particles (UFPs). Air pollution source apportionment is essential for implementation of successful abatement strategies. UFPs or nanoparticles of diameter hot-spot including nanoparticles, Positive Matrix Factorization (PMF) was applied to highly time resolved particle number size distributions (NSD, 14 nm-10 μm) and PM 0.09-1.15 chemical composition. Diurnal patterns, meteorological variables, gaseous pollutants, organic markers, and associations between the NSD factors and chemical composition factors were used to identify the pollution sources. The PMF on the NSD reveals two factors in the ultrafine size range: industrial UFPs (28%, number mode diameter - NMD 45 nm), industrial/fresh road traffic nanoparticles (26%, NMD 26 nm); three factors in the accumulation size range: urban background (24%, NMD 93 nm), coal burning (14%, volume mode diameter - VMD 0.5 μm), regional pollution (3%, VMD 0.8 μm) and one factor in the coarse size range: industrial coarse particles/road dust (2%, VMD 5 μm). The PMF analysis of PM 0.09-1.15 revealed four factors: SIA/CC/BB (52%), road dust (18%), sinter/steel (16%), iron production (16%). The factors in the ultrafine size range resolved with NSD have a positive correlation with sinter/steel production and iron production factors resolved with chemical composition. Coal combustion factor resolved with NSD has moderate correlation with SIA/CC/BB factor. The organic markers homohopanes correlate with coal combustion and the levoglucosan correlates with urban background. The PMF applications to NSD and chemical composition datasets are complementary. PAHs in PM 1 were found to be associated with coal combustion factor. Copyright © 2017 Elsevier Ltd. All rights reserved.

Aerosol composition and sources during the Chinese Spring Festival: fireworks, secondary aerosol, and holiday effects

Science.gov (United States)

Jiang, Q.; Sun, Y. L.; Wang, Z.; Yin, Y.

2015-06-01

Aerosol particles were characterized by an Aerodyne aerosol chemical speciation monitor along with various collocated instruments in Beijing, China, to investigate the role of fireworks (FW) and secondary aerosol in particulate pollution during the Chinese Spring Festival of 2013. Three FW events, exerting significant and short-term impacts on fine particles (PM2.5), were observed on the days of Lunar New Year, Lunar Fifth Day, and Lantern Festival. The FW were shown to have a large impact on non-refractory potassium, chloride, sulfate, and organics in submicron aerosol (PM1), of which FW organics appeared to be emitted mainly in secondary, with its mass spectrum resembling that of secondary organic aerosol (SOA). Pollution events (PEs) and clean periods (CPs) alternated routinely throughout the study. Secondary particulate matter (SPM = SOA + sulfate + nitrate + ammonium) dominated the total PM1 mass on average, accounting for 63-82% during nine PEs in this study. The elevated contributions of secondary species during PEs resulted in a higher mass extinction efficiency of PM1 (6.4 m2 g-1) than during CPs (4.4 m2 g-1). The Chinese Spring Festival also provides a unique opportunity to study the impact of reduced anthropogenic emissions on aerosol chemistry in the city. Primary species showed ubiquitous reductions during the holiday period with the largest reduction being in cooking organic aerosol (OA; 69%), in nitrogen monoxide (54%), and in coal combustion OA (28%). Secondary sulfate, however, remained only slightly changed, and the SOA and the total PM2.5 even slightly increased. Our results have significant implications for controlling local primary source emissions during PEs, e.g., cooking and traffic activities. Controlling these factors might have a limited effect on improving air quality in the megacity of Beijing, due to the dominance of SPM from regional transport in aerosol particle composition.

Determining Isotopic Composition of Dissolved Nitrate Using Bacterial Denitrification Followed by Laser Spectroscopy

International Nuclear Information System (INIS)

Yan Tiezhu; Lee Zhi Yi, Amelia; Heiling, Maria; Weltin, Georg; Toloza, Arsenio; Resch, Christian

2016-01-01

Nitrate (NO_3"-) pollution is a prevalent problem that can cause water quality degradation and eutrophication of water bodies. Quantifying the nitrogen and oxygen isotopic composition of nitrates will allow for better identification of their potential sources, which in turn will assist in remediation of contaminated water and the designing of future water management practices. In this research bacterial denitrification followed by laser spectroscopy are used to determine isotopic composition of δ"1"5N and δ"1"8O of dissolved nitrates. The objective of the project is to establish a standard operating procedure (SOP) that outlines the best practices for both methods in sequence and designed to be used as a technical guideline

Determining Isotopic Composition of Dissolved Nitrate Using Bacterial Denitrification Followed by Laser Spectroscopy

International Nuclear Information System (INIS)

Yan Tiezhu; Lee Zhi Yi, Amelia; Heiling, Maria; Weltin, Georg; Toloza, Arsenio; Resch, Christian

2016-01-01

Nitrate (NO 3 - ) pollution is a prevalent problem that can cause water quality degradation and eutrophication of water bodies. Quantifying the nitrogen and oxygen isotopic composition of nitrates will allow for better identification of their potential sources, which in turn will assist in remediation of contaminated water and the designing of future water management practices. In this research bacterial denitrification followed by laser spectroscopy are used to determine isotopic composition of δ 15 N and δ 18 O of dissolved nitrates. The objective of the project is to establish a standard operating procedure (SOP) that outlines the best practices for both methods in sequence and designed to be used as a technical guideline

Study of Water Quality Value in Sub of the Stream Area of Cisadane Rivers Upstream as Reference Area Based on Macro invertebrate Composition

International Nuclear Information System (INIS)

Sri-Unon-Purwati

2001-01-01

Specific structure of biota community condition can used as indicator for the ecosystem stability value or the waters pollution level where the aquatic biota exist. the macro invertebrates as bio indicator organism can used to assess the upper Cisadane Sub River Basin water quality. The grouping and calculation result from family number, Ept presences (sensitive macro invertebrate), Diversity index (H ' ), DO value and TOC value showed 5 criteria of water quality as reference site. This criteria is used to determine water quality level from ten branches of rivers in the upper Cisadane Sub River Basin, Cijeruk districts. The biotic index calculation for ASPT (Average Score Per Taxon) and T and T (index Trihadiningrum and Tjindronegoro) is used to asses water quality based on macro invertebrate composition indicator. Both biotic index system support and give the similar evaluation to water quality level from ten branches of river on the upper Cisadane Sub River Basin. The water quality level is described as fellows: station number 4 is assumed as the true reference site, station number 3, 5, 8 are the first alternative reference site, station number 2, 7, 9 are the second alternative reference site and station 1, 6, 10 are the sites which relatively good water quality, but it is not recommended as reference site. The grouping result bases on the cluster system with macro invertebrate similarity composition are described as fellows: 9=10>3=7>1=6>2=8>>5>>4. (author)

Application of central composite design to optimize the amount of carbon source and prebiotics for Bifidobacterium bifidum BB01

Directory of Open Access Journals (Sweden)

Shu Guowei

2016-06-01

Full Text Available The objective of the present study was to obtain the optimum proportion of the carbon source and prebiotics for Bifidobacterium bifidum BB01 by the central composite design (CCD. The effect of carbon source (lactose and two prebiotics (inulin and fructooligosaccharides on the BB01 were observed by measuring the OD600 value, pH value and the viable counts at 18h. The final optimized concentrations of carbon source and prebiotics were: lactose 1.6%, inulin 0.26%, and fructooligosaccharides 0.22%. The result indicates that the growth of B. bifidum BB01 shows an significant increase in the optimized culture medium (p < 0.05, the OD600 value reached 1.434 at 18h, which increased 6.58% compared to the control. And the viable counts of B. bifidum BB01 increased 24.36% and reached (2.17±0.06 ×109cfu/mL. The results show that the optimization of the carbon source and prebiotics using CCD in this study is workable and necessary.

Changes in Acylglycerols composition, quality characteristics and in vivo effects of dietary pumpkin seed oil upon thermal oxidation

Science.gov (United States)

Zeb, Alam; Ahmad, Sultan

2017-07-01

This study was aimed to determine the acylglycerols composition, quality characteristics and protective role of dietary pumpkin seed oil in rabbits. Pumpkin seed oil was thermally oxidized and analyzed for quality characteristics and acylglycerols composition using reversed phase high performance liquid chromatography with diode array detection (HPLC-DAD). Oxidized and un-oxidized oil samples were fed to the rabbits in different doses for two weeks. The changes in the serum biochemistry, hematology, and liver histology were studied. The levels of quality parameters such peroxide value (PV), anisidine value (AV), total phenolic contents (TPC), thiobarbituric acid reactive substances (TBARS), conjugated dienes (CD) and conjugated trienes (CT) significantly increased with thermal treatment. HPLC analyses revealed ten individual triacylglycerols (TAGs), total di-acylglycerols (DAGs), mono-acylglycerols (MAGs), and total oxidized TAGs. Trilinolein (LLL), 1-oleoyl-2,3-dilinolinoyl glycerol (OLL), triolein (OOO) and 1,2-distearoyl-3-palmitoyl glycerol (SSP) were present in higher amounts and decreased with thermal treatment. Animal's studies showed that oxidized oils decreased the whole body weight, which was ameliorated by the co-administration of un-oxidized oils. The levels of serum biochemical parameters were improved by co-administration of pumpkin seed oils. There were no significant effects of both oxidized and un-oxidized pumpkin seed oil on the hematological and histological parameters of rabbits. In conclusion, nutritionally important triacylglycerols were present in pumpkin seed oil with protective role against the toxicity of its corresponding oxidized oils.

Changes in Acylglycerols Composition, Quality Characteristics and In vivo Effects of Dietary Pumpkin Seed Oil upon Thermal Oxidation

Directory of Open Access Journals (Sweden)

Alam Zeb

2017-07-01

Full Text Available This study was aimed to determine the acylglycerols composition, quality characteristics, and protective role of dietary pumpkin seed oil (PSO in rabbits. PSO was thermally oxidized and analyzed for quality characteristics and acylglycerols composition using reversed phase high performance liquid chromatography with diode array detection (HPLC-DAD. Oxidized and un-oxidized oil samples were fed to the rabbits in different doses for 2 weeks. The changes in the serum biochemistry, hematology, and liver histology were studied. The levels of quality parameters such peroxide value (PV, anisidine value (AV, total phenolic contents (TPC, thiobarbituric acid reactive substances (TBARS, conjugated dienes (CD and conjugated trienes (CT significantly increased with thermal treatment. HPLC analyses revealed 10 individual triacylglycerols (TAGs, total di-acylglycerols (DAGs, mono-acylglycerols (MAGs, and total oxidized TAGs. Trilinolein (LLL, 1-oleoyl-2,3-dilinolinoyl glycerol (OLL, triolein (OOO and 1,2-distearoyl-3-palmitoyl glycerol (SSP were present in higher amounts and decreased with thermal treatment. Animal's studies showed that oxidized oils decreased the whole body weight, which was ameliorated by the co-administration of un-oxidized oils. The levels of serum biochemical parameters were improved by co-administration of pumpkin seed oils. There were no significant effects of both oxidized and un-oxidized PSO on the hematological and histological parameters of rabbits. In conclusion, nutritionally important triacylglycerols were present in PSO with protective role against the toxicity of its corresponding oxidized oils.

Water quality assessment and apportionment of pollution sources using APCS-MLR and PMF receptor modeling techniques in three major rivers of South Florida.

Science.gov (United States)

Haji Gholizadeh, Mohammad; Melesse, Assefa M; Reddi, Lakshmi

2016-10-01

In this study, principal component analysis (PCA), factor analysis (FA), and the absolute principal component score-multiple linear regression (APCS-MLR) receptor modeling technique were used to assess the water quality and identify and quantify the potential pollution sources affecting the water quality of three major rivers of South Florida. For this purpose, 15years (2000-2014) dataset of 12 water quality variables covering 16 monitoring stations, and approximately 35,000 observations was used. The PCA/FA method identified five and four potential pollution sources in wet and dry seasons, respectively, and the effective mechanisms, rules and causes were explained. The APCS-MLR apportioned their contributions to each water quality variable. Results showed that the point source pollution discharges from anthropogenic factors due to the discharge of agriculture waste and domestic and industrial wastewater were the major sources of river water contamination. Also, the studied variables were categorized into three groups of nutrients (total kjeldahl nitrogen, total phosphorus, total phosphate, and ammonia-N), water murkiness conducive parameters (total suspended solids, turbidity, and chlorophyll-a), and salt ions (magnesium, chloride, and sodium), and average contributions of different potential pollution sources to these categories were considered separately. The data matrix was also subjected to PMF receptor model using the EPA PMF-5.0 program and the two-way model described was performed for the PMF analyses. Comparison of the obtained results of PMF and APCS-MLR models showed that there were some significant differences in estimated contribution for each potential pollution source, especially in the wet season. Eventually, it was concluded that the APCS-MLR receptor modeling approach appears to be more physically plausible for the current study. It is believed that the results of apportionment could be very useful to the local authorities for the control and

Effects of Dietary Lipid Source and Level on Growth Performance, Blood Parameters and Flesh Quality of Sub-adult Olive Flounder (

Directory of Open Access Journals (Sweden)

Dong-Kyu Kim

2012-06-01

Full Text Available This study was conducted to investigate the effects of dietary lipid source and level on growth performance, blood parameters, fatty acid composition and flesh quality of sub-adult olive flounder Paralichthys olivaceus. Eight experimental diets were formulated to contain 5% squid liver oil (SLO, 5% linseed oil (LO, 5% soybean oil (SO, a mixture of 1% squid liver oil, 2% linseed oil and 2% soybean oil (MIX, no lipid supplementation with high protein level (LL-HP, 10% squid liver oil (HL-SLO, a mixture of 1% squid liver oil, 4.5% linseed oil and 4.5% soybean oil (HL-VO, and 1% squid liver oil with high starch level (LL-HC, respectively. Two replicate groups of fish (average initial weight of 296 g were fed the diets for 17 wks. After 5 wks, 11 wks and the end of the feeding trial, five fish from each tank were randomly sampled for analysis of body composition. At the end of the feeding trial, final mean weight of fish fed the LL-HP diet was significantly (p<0.05 higher than that of fish fed the HL-VO diet, but did not differ significantly from those of fish fed the SLO, LO, SO, MIX, HL-SLO and LL-HC diets. Fish fed the LL-HP diet showed significantly higher feed efficiency than fish fed the LO, HL-SLO and HL-VO diets. Feed efficiency of fish fed the LO, SO and MIX diets were similar to those of fish fed the SLO and HL-SLO diets. Fish fed the HL-SLO diet showed significantly higher total cholesterol content in plasma compared with other diets. Fatty acid composition of tissues was reflected by dietary fatty acid composition. The highest linoleic (LA and linolenic acid (LNA contents in the dorsal muscle were observed in fish fed the SO and LO diets, respectively, regardless of feeding period. The highest eicosapentaenoic acid (EPA content in the dorsal muscle was observed in fish fed the LL-HP and LL-HC diets after 11 and 17 weeks of feeding, respectively. Fish fed the SLO and HL-SLO diets showed higher docosahexaenoic acid (DHA content than that of

Metal-organic chemical vapor deposition of high quality, high indium composition N-polar InGaN layers for tunnel devices