WorldWideScience

Sample records for sour produced water

  1. Strategies to diagnose and control microbial souring in natural gas storage reservoirs and produced water systems

    Energy Technology Data Exchange (ETDEWEB)

    Morris, E.A.; Derr, R.M.; Pope, D.H.

    1995-12-31

    Hydrogen sulfide production (souring) in natural gas storage reservoirs and produced water systems is a safety and environmental problem that can lead to operational shutdown when local hydrogen sulfide standards are exceeded. Systems affected by microbial souring have historically been treated using biocides that target the general microbial community. However, requirements for more environmentally friendly solutions have led to treatment strategies in which sulfide production can be controlled with minimal impact to the system and environment. Some of these strategies are based on microbial and/or nutritional augmentation of the sour environment. Through research sponsored by the Gas Research Institute (GRI) in Chicago, Illinois, methods have been developed for early detection of microbial souring in natural gas storage reservoirs, and a variety of mitigation strategies have been evaluated. The effectiveness of traditional biocide treatment in gas storage reservoirs was shown to depend heavily on the methods by which the chemical is applied. An innovative strategy using nitrate was tested and proved ideal for produced water and wastewater systems. Another strategy using elemental iodine was effective for sulfide control in evaporation ponds and is currently being tested in microbially sour natural gas storage wells.

  2. The effect of produced water reinjection on reservoir souring in the Statfjord field

    Energy Technology Data Exchange (ETDEWEB)

    Bjoernestad, Eva Oe.; Sunde, Egil; Dinning, Anthony J.

    2006-03-15

    A produced water reinjection (PWRI) pilot test was performed in one well in the Statfjord field in the period 2000-2001. In order to establish the souring parameters and influence of PWRI in the near well area, the well was back flowed prior to PWRI, and at the end of the PWRI test period. Tracer was used for mass balance evaluations. After the PWRI pilot test was finished, the PWRI plant was upgraded at the Statfjord C platform and since 2003; two wells have been re injecting produced water. Nitrate has substituted biocides for corrosion control in the water injection system at the Statfjord B and Statfjord C platforms. Based on experience from other Statoil operated fields, nitrate will improve the corrosion control and in addition reduce the reservoir souring and hence the H2S production. In 2004, three wells were backflowed; a PWRI- injector, a seawater injector and a sea water injector with addition of nitrate. Results from the PWRI pilot test, showed that the sulphide production increased 17 times after PWRI in comparison with seawater injection. In the backflowing studies in 2004, water from the PWRI injector showed considerable higher H2S content (approximately 300 mg/l) than the well injecting only seawater (approximately 3-4 mg/l). The well injecting nitrate showed the lowest sulphide concentration in the backflowed fluids in comparison with the other wells (below 1 mg/l). This illustrates a significant increase in microbiological activity within the near injection area as a result of increased nutrient availability due to PWRI. The impact of PWRI in the lifetime of the Statfjord field has been evaluated and the PWRI strategy may be altered due to increases in souring. (Author)

  3. A field demonstration of the microbial treatment of sour produced water

    Energy Technology Data Exchange (ETDEWEB)

    Sublette, K.L. [Univ. of Tulsa, OK (United States); Morse, D.; Raterman, K. [Amoco Production Co., Tulsa, OK (United States)

    1995-12-31

    The potential for detoxification and deodorization of sulfide-laden water (sour water) by microbial treatment was evaluated at a petroleum production site under field conditions. A sulfide-tolerant strain of the chemautotroph and facultative anaerobe, Thiobacillus denitrificans, was introduced into an oil-skimming pit of the Amoco Production Company LACT 10 Unit of the Salt Creek Field, Wyoming. Field-produced water enters this pit from the oil/water separation treatment train at an average flowrate of 5,000 bbl/D (795 m{sup 3}/D) with a potential maximum of 98,000 bbl/D (15,580 m{sup 3}/D). Water conditions at the pit inlet are 4,800 mg/l TDS, 100 mg/l sulfide, pH 7.8, and 107{degrees}F. To this water an aqueous solution of ammonium nitrate and diphosphorous pentoxide was added to provide required nutrients for the bacteria. The first 20% of the pit was aerated to a maximum depth of 5 ft (1.5 m) to facilitate the aerobic oxidation of sulfide. No provisions for pH control or biomass recovery and recycle were made. Pilot operations were initiated in October 1992 with the inoculation of the 19,000 bbl (3,020 m{sup 3}) pit with 40 lb (18.1 kg) of dry weight biomass. After a brief acclimation period, a nearly constant mass flux of 175 lb/D (80 kg/D) sulfide was established to the pit. Bio-oxidation of sulfide to elemental sulfur and sulfate was immediate and complete. Subsequent pilot operations focused upon process optimization and process sensitivity to system upsets. The process appeared most sensitive to large variations in sulfide loading due to maximum water discharge events. However, recoveries from such events could be accomplished within hours. This paper details all pertinent aspects of pilot operation, performance, and economics. Based on this body of evidence, it is suggested that the oxidation of inorganic sulfides by T denitrificans represents a viable concept for the treatment of sour water coproduced with oil and gas.

  4. Reservoir souring: it is all about risk mitigation

    Energy Technology Data Exchange (ETDEWEB)

    Kuijvenhoven, Cor [Shell (Canada)

    2011-07-01

    The presence of H2S in produced fluid can be due to various sources, among which are heat/rock interaction and leaks from other reservoirs. This paper discusses the reasons, risk assessment and tools for mitigating reservoir souring. Uncontrolled microorganism activity can cause a sweet reservoir (without H2S) to become sour (production of H2S). The development of bacteria is one of the main causes of reservoir souring in unconventional gas fields. It is difficult to predict souring in seawater due to produced water re-injection (PWRI). Risk assessment and modeling techniques for reservoir souring are discussed. Some of the factors controlling H2S production include injection location, presence of scavenging minerals and biogenic souring. Mitigation methods such as biocide treatment of injection water, sulphate removal from seawater, microbial monitoring techniques such as the molecular microbiology method (MMM), and enumeration by serial dilution are explained. In summary, it can be concluded that reservoir souring is a long-term problem and should be assessed at the beginning of operations.

  5. Tekna's produced water conference 2005

    International Nuclear Information System (INIS)

    2005-01-01

    The conference has 22 presentations discussing topics on discharge reduction, produced water quality, produced water re-injection, chemicals particularly environmentally friendly ones, separation technology, reservoir souring, total water management systems, pollution, oil in water problems and platform operation. Various field tests and experiences particularly from the offshore petroleum sector are presented (tk)

  6. Tekna's produced water conference 2005

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    The conference has 22 presentations discussing topics on discharge reduction, produced water quality, produced water re-injection, chemicals particularly environmentally friendly ones, separation technology, reservoir souring, total water management systems, pollution, oil in water problems and platform operation. Various field tests and experiences particularly from the offshore petroleum sector are presented (tk)

  7. The chemistry of sour taste and the strategy to reduce the sour taste of beer.

    Science.gov (United States)

    Li, Hong; Liu, Fang

    2015-10-15

    The contributions of free hydrogen ions, undissociated hydrogen ions in protonated acid species, and anionic acid species to sour taste were studied through sensory experiments. According to tasting results, it can be inferred that the basic substance producing a sour taste is the hydrogen ion, including free hydrogen ions and undissociated hydrogen ions. The intensity of a sour taste is determined by the total concentration of free hydrogen ions and undissociated hydrogen ions. The anionic acid species (without hydrogen ions) does not produce a sour taste but can intensify or weaken the intensity of a sour taste. It seems that hydroxyl or conjugated groups in anionic acid species can intensify the sour taste produced by hydrogen ions. The following strategy to reduce the sensory sourness is advanced: not only reduce free hydrogen ions, namely elevate pH value, but also reduce the undissociated hydrogen ions contained in protonated acid species. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Primary souring: A novel bacteria-free method for sour beer production.

    Science.gov (United States)

    Osburn, Kara; Amaral, Justin; Metcalf, Sara R; Nickens, David M; Rogers, Cody M; Sausen, Christopher; Caputo, Robert; Miller, Justin; Li, Hongde; Tennessen, Jason M; Bochman, Matthew L

    2018-04-01

    In the beverage fermentation industry, especially at the craft or micro level, there is a movement to incorporate as many local ingredients as possible to both capture terroir and stimulate local economies. In the case of craft beer, this has traditionally only encompassed locally sourced barley, hops, and other agricultural adjuncts. The identification and use of novel yeasts in brewing lags behind. We sought to bridge this gap by bio-prospecting for wild yeasts, with a focus on the American Midwest. We isolated 284 different strains from 54 species of yeast and have begun to determine their fermentation characteristics. During this work, we found several isolates of five species that produce lactic acid and ethanol during wort fermentation: Hanseniaspora vineae, Lachancea fermentati, Lachancea thermotolerans, Schizosaccharomyces japonicus, and Wickerhamomyces anomalus. Tested representatives of these species yielded excellent attenuation, lactic acid production, and sensory characteristics, positioning them as viable alternatives to lactic acid bacteria (LAB) for the production of sour beers. Indeed, we suggest a new LAB-free paradigm for sour beer production that we term "primary souring" because the lactic acid production and resultant pH decrease occurs during primary fermentation, as opposed to kettle souring or souring via mixed culture fermentation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Development of a novel processing system for efficient sour water stripping

    International Nuclear Information System (INIS)

    Kazemi, Abolghasem; Mehrabani-Zeinabad, Arjomand; Beheshti, Masoud

    2017-01-01

    Application of vapor recompression systems can result in enhanced energy efficiency and reduced energy requirements of distillation systems. In vapor recompression systems, temperature and dew point temperature of the top product of the column are increased through compression. By transferring heat from top to bottoms product, required boil up and reflux streams for the column are provided. In this paper, a new system is proposed for efficient stripping of sour water based on vapor recompression. Ammonia and H 2 S are the contaminants of sour water. Initially, based on a certain specifications of products, a sour water stripping system is implemented. A novel processing system is then developed and simulated to reduce utility requirements. The two processing systems are economically evaluated by Aspen Economic Evaluation software. There are 89.0% and 83.7% reduction of hot and cold utility requirements for the proposed system in comparison to the base processing system. However, the new processing system requires new equipment such as compressor and corresponding mechanical work that increases its capital and operating costs in comparison to the base case. However, the results indicate that the proposed system results in reduction of 11.4% of total annual costs and 14.9% of operating costs. - Highlights: • A novel system was developed for enhancement of performance of a distillation system based on vapor recompression. • In this system, utility streams are used for providing thermal energy. • A parametric study is carried out on the proposed processing system. • Applying the proposed system resulted in reduction of energy and utility requirements and costs of the separation process. • Environmental performance of the model was investigated.

  10. Corrosion of steels in sour gas environments

    International Nuclear Information System (INIS)

    Twigg, R.J.

    1984-03-01

    This report presents a study on the effects of sour gas environments on steels. Emphasis is placed on alloys commonly used in the heavy water, sour gas and refining industries. In addition, 'high strength, low alloy' steels, known as 'oil country tubular goods', are included. Reference is made to the effects of hydrogen sulphide environments on austenitic steels and on certain specialty steels. Theories of hydrogen-related cracking mechanisms are outlined with emphasis placed on sulphide stress cracking and hydrogen induced cracking in carbon and low alloy steels. Methods of controlling sulphide stress cracking and hydrogen induced cracking are addressed separately. Case histories from the heavy water, refining, and sour gas industries are used to illustrate operating experience and failure mechanisms. Finally, recommendations, based largely on the author's industrial experience, are made with respect to quality assurance and inspection requirements for sour service components. Only published literature was surveyed. Abstracts were made of all references, reviewing the major sources in detail

  11. Analytical and sensorial characterization of the aroma of wines produced with sour rotten grapes using GC-O and GC-MS: identification of key aroma compounds.

    Science.gov (United States)

    Barata, André; Campo, Eva; Malfeito-Ferreira, Manuel; Loureiro, Virgílio; Cacho, Juan; Ferreira, Vicente

    2011-03-23

    In the present work, the aroma profiles of wines elaborated from sound and sour rot-infected grapes as raw material have been studied by sensory analysis, gas chromatography-olfactometry (GC-O), and gas chromatography-mass spectrometry (GC-MS), with the aim of determining the odor volatiles most likely associated with this disease. The effect of sour rot was tested in monovarietal wines produced with the Portuguese red grape variety Trincadeira and in blends of Cabernet Sauvignon and sour rotten Trincadeira grapes. Wines produced from damaged berries exhibited clear honey-like notes not evoked by healthy samples. Ethyl phenylacetate (EPhA) and phenylacetic acid (PAA), both exhibiting sweet honey-like aromas, emerged as key aroma compounds of sour rotten wines. Their levels were 1 order of magnitude above those found in controls and reached 304 and 1668 μg L(-1) of EPhA and PAA, respectively, well above the corresponding odor thresholds. Levels of γ-nonalactone also increased by a factor 3 in sour rot samples. Results also suggest that sour rot exerts a great effect on the secondary metabolism of yeast, decreasing the levels of volatiles related to fatty acids and amino acid synthesis. The highest levels of γ-decalactone of up to 405 μg L(-1) were also found in all of the samples, suggesting that this could be a relevant aroma compound in Trincadeira wine aroma.

  12. Influence of ph on corrosion control of carbon steel by peroxide injection in sour water

    Energy Technology Data Exchange (ETDEWEB)

    Vieira, Martins Magda; Baptista, Walmar; Joia, Carlos Jose Bandeira de Mello [PROTEMP - PETROBRAS/CENPES, Cidade Universitaria, Quadra 7, Rio de Janeiro, CEP 21949-900 (Brazil); Ponciano, Gomes Jose Antonio da Cunha [Departamento de Engenharia Metalurgica e de Materiais-COPPE/UFRJ, Cidade Universitaria, Rio de Janeiro (Brazil)

    2004-07-01

    Sour hydrogen damage is considered the most important corrosive process in the light-ends recovery section of Fluid Catalytic Cracking Units (FCCU). Corrosion in this condition is due to heavy gas oil that originates great amount of contaminants, such as H{sub 2}S, NH{sub 3} and HCN. Hydrogen absorption is promoted by the presence of free cyanides in the environment. The attenuation of this process requires the use of some inhibitors, such as oxygen, hydrogen peroxide (H{sub 2}O{sub 2}) or commercial polysulfides. The effect of these compounds is to neutralize free cyanides (CN{sup -}) into thio-sulfides (SCN{sup -}). When peroxide injection is selected, cyanide concentration in sour water has been used as key parameter to start the peroxide introduction. However, the importance of pH in this system has been pointed out by many authors. The aim of this work is to investigate the influence of pH when peroxide injection is carried out in less alkaline conditions of sour water. Electrochemical techniques - like anodic polarization and hydrogen permeation tests - and weight loss measurements were used to evaluate the effectiveness of corrosion control of carbon steel. It was concluded that at pH 7.5 peroxide injection can drive to an increment of the corrosion rate. Besides that, it was concluded that hydrogen permeation into the metal is promoted. Both detrimental effects were due to elemental sulfur generation in this pH range. The adoption of pH as a key parameter for peroxide injection is then suggested. (authors)

  13. Analysis of the structural steels corrosion resistance in sour water from petroleum refineries; Analise da resistencia a corrosao de acos estruturais em aguas acidas de refinarias de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Proenca, Marcos B.; Freire, Celia M. de A. [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica; Santos, Margatita B. [Universidade Estadual de Campinas, SP (Brazil). Inst. de Fisica. Dept. de Fisica Aplicada

    1994-07-01

    The presence of H{sub 2} S in refineries FCC sour water provokes the formation of a passive Fe S scale. The cyanides present on sour water remove this scale, raising the corrosion rate in pipping and vessels. In this work it was measured the corrosion rate of structural steels in this water by electrochemical methods. Anodic polarization curves were plotted and the corrosion rates of the steels were determined. (author)

  14. A review of the implications of sour gas setbacks on the ability to develop property : public safety and sour gas recommendation 53

    International Nuclear Information System (INIS)

    2005-09-01

    All sour gas facilities in Alberta have a required setback, which is the minimum distance that must be maintained between the energy facility and a dwelling, rural housing development, urban centre or public facility. The size of the setback depends on the classification levels of the sour gas facilities. This paper reviewed the economic implications of sour gas setback restrictions for landowners with reference to Recommendation 53. The methodology of the study included a telephone and electronic mail survey to prequalify municipalities, cities and towns located in the sour gas producing regions of Alberta and the selection of 11 cases for further detailed analysis. The findings of the survey and case studies were then used to examine whether landowners were treated fairly in cases where a setback impact occurred. The frequency of setback incidents was described as common by 13 jurisdictions, occasional by 33 jurisdictions and as emerging by 30 jurisdictions. Results indicated that impacts on property development due to sour gas setbacks were widespread across the province. Observed mitigation measures included the modification of development plans by landowners to avoid setback restrictions; encouraging land development proposals away from areas known to have sour gas activity; and the oil and gas industry working with landowners to locate proposed facilities in order to minimize setback restrictions. Results of the survey suggested that ineffective communication was the predominant factor leading to conflicts, particularly when parties were not familiar with setback requirements or the implications for property development. It was suggested that policy makers should aim to reduce the number of conflicts between sour gas setbacks and property development. Recommendations to improve communication included closing gaps in regulations, processes and practices; and reducing surface and subsurface interface conflicts. 9 refs., 1 tab., 4 figs

  15. Effects of nitrate injection on microbial enhanced oil recovery and oilfield reservoir souring.

    Science.gov (United States)

    da Silva, Marcio Luis Busi; Soares, Hugo Moreira; Furigo, Agenor; Schmidell, Willibaldo; Corseuil, Henry Xavier

    2014-11-01

    Column experiments were utilized to investigate the effects of nitrate injection on sulfate-reducing bacteria (SRB) inhibition and microbial enhanced oil recovery (MEOR). An indigenous microbial consortium collected from the produced water of a Brazilian offshore field was used as inoculum. The presence of 150 mg/L volatile fatty acids (VFA´s) in the injection water contributed to a high biological electron acceptors demand and the establishment of anaerobic sulfate-reducing conditions. Continuous injection of nitrate (up to 25 mg/L) for 90 days did not inhibit souring. Contrariwise, in nitrogen-limiting conditions, the addition of nitrate stimulated the proliferation of δ-Proteobacteria (including SRB) and the associated sulfide concentration. Denitrification-specific nirK or nirS genes were not detected. A sharp decrease in water interfacial tension (from 20.8 to 14.5 mN/m) observed concomitantly with nitrate consumption and increased oil recovery (4.3 % v/v) demonstrated the benefits of nitrate injection on MEOR. Overall, the results support the notion that the addition of nitrate, at this particular oil reservoir, can benefit MEOR by stimulating the proliferation of fortuitous biosurfactant-producing bacteria. Higher nitrate concentrations exceeding the stoichiometric volatile fatty acid (VFA) biodegradation demands and/or the use of alternative biogenic souring control strategies may be necessary to warrant effective SRB inhibition down gradient from the injection wells.

  16. Identification of crude-oil components and microorganisms that cause souring under anaerobic conditions.

    Science.gov (United States)

    Hasegawa, R; Toyama, K; Miyanaga, K; Tanji, Y

    2014-02-01

    Oil souring has important implications with respect to energy resources. Understanding the physiology of the microorganisms that play a role and the biological mechanisms are both important for the maintenance of infrastructure and mitigation of corrosion processes. The objective of this study was to identify crude-oil components and microorganisms in oil-field water that contribute to crude-oil souring. To identify the crude-oil components and microorganisms that are responsible for anaerobic souring in oil reservoirs, biological conversion of crude-oil components under anaerobic conditions was investigated. Microorganisms in oil field water in Akita, Japan degraded alkanes and aromatics to volatile fatty acids (VFAs) under anaerobic conditions, and fermenting bacteria such as Fusibacter sp. were involved in VFA production. Aromatics such as toluene and ethylbenzene were degraded by sulfate-reducing bacteria (Desulfotignum sp.) via the fumarate-addition pathway and not only degradation of VFA but also degradation of aromatics by sulfate-reducing bacteria was the cause of souring. Naphthenic acid and 2,4-xylenol were not converted.

  17. Organic acid profile of commercial sour cassava starch

    Directory of Open Access Journals (Sweden)

    DEMIATE I.M.

    1999-01-01

    Full Text Available Organic acids are present in sour cassava starch ("polvilho azedo" and contribute with organoleptic and physical characteristics like aroma, flavor and the exclusive baking property, that differentiate this product from the native cassava starch. Samples of commercial sour cassava starch collected in South and Southeast Brazil were prepared for high performance liquid chromatography (HPLC analysis. The HPLC equipment had a Biorad Aminex HPX-87H column for organic acid analysis and a refractometric detector. Analysis was carried out with 0.005M sulfuric acid as mobile phase, 0.6ml/min flow rate and column temperature of 60° C. The acids quantified were lactic (0.036 to 0.813 g/100g, acetic (0 to 0.068 g/100g, propionic (0 to 0.013 g/100g and butyric (0 to 0.057 g/100g, that are produced during the natural fermentation of cassava starch. Results showed large variation among samples, even within the same region. Some samples exhibited high acid levels, mainly lactic acid, but in these neither propionic nor butyric acids were detected. Absence of butyric acid was not expected because this is an important component of the sour cassava starch aroma, and the lack of this acid may suggest that such samples were produced without the natural fermentation step.

  18. Produced water reinjection in Campos Basin; Reinjecao de agua produzida na Bacia de Campos

    Energy Technology Data Exchange (ETDEWEB)

    Mendes, Roberta A.; Furtado, Claudio J.A.; Luz Junior, Euripedes B. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2008-07-01

    To manage the increasing volume of produced water became one of the main challenges in the petroleum industry. PWRI (produced water re-injection) leads to a decrease operational cost in platforms, an increase in liquid flow rates on the topside facilities and a decrease in surface disposal of water. Nowadays in Brazilian fields for every barrel of produced oil three barrels of water need to be handled. PWRI is a process that has been widely diffused in many fields in the world. The main advantages of the PWRI are to reduce collected water, to decrease or eliminate surface disposal of produced water, and to help oil recovery. On the other hand, PWRI tends to increase corrosion when inappropriate materials in tubing and pipelines are used; increase souring potential due to the amount of nutrients for bacteria in the produced water; increase scale formation when sea-water and produced water are mixed and increase formation damage. Even in reservoirs with good qualities in terms of permeability and porosity, the poor quality of the reinjection water decreases injectivity. To minimize injectivity loss some requirements are important: to avoid solids in the produced water system, to inject above fracture propagation pressure to maintain injectivity whenever possible, to use compatible the chemical products for oil-water separation to avoid the formation solids-oil agglomerates. (author)

  19. Organic constituents in sour condensates from shale-oil and petroleum-crude runs at Sohio's Toledo refinery: identification and wastewater-control-technology considerations

    Energy Technology Data Exchange (ETDEWEB)

    Wingender, R J; Harrison, W; Raphaelian, L A

    1981-02-01

    Samples of sour condensate generated from the continuous processing of both crude shale oil and petroleum crude were collected and extracted with methylene chloride. The extracts were analyzed using capillary-column gas chromatography/mass spectrometry at Argonne National Laboratory and Radian Corporation. Qualitatively, the predominant types of organic compounds present in the shale-oil sour condensate were pyridines and anilines; semiquantitatively, these compounds were present at a concentration of 5.7 ppM, or about 78% of the total concentration of components detected. In contrast, straight-chain alkanes were the predominant types of compounds found in the sour condensate produced during isocracking of conventional crude oil. The approximate concentration of straight-chain alkanes, 8.3 ppM, and of other branched and/or unsaturated hydrocarbons, 6.8 ppM, amounted to 88% of the total concentration of components detected in the sour condensate from the petroleum-crude run. Nitrogen compounds in the shale-oil sour condensate may necessitate alterations of the sour water and refinery wastewater-treatment facilities to provide for organics degradation and to accommodate the potentially greater ammonia loadings. This would include use of larger amounts of caustic to enhance ammonia removal by steam stripping. Possible problems associated with biological removal of organic-nitrogen compounds should be investigated in future experimental shale-oil refining runs.

  20. Music to Make Your Mouth Water? Assessing the Potential Influence of Sour Music on Salivation

    Science.gov (United States)

    Wang, Qian J.; Knoeferle, Klemens; Spence, Charles

    2017-01-01

    People robustly associate various sound attributes with specific smells/tastes, and soundtracks that are associated with specific tastes can influence people’s evaluation of the taste of food and drink. However, it is currently unknown whether such soundtracks directly impact the eating experience via physiological changes (an embodiment account), or whether they act at a higher cognitive level, or both. The present research assessed a version of the embodiment account, where a soundtrack associated with sourness is hypothesized to induce a physiological response in the listener by increasing salivary flow. Salivation was measured while participants were exposed to three different experimental conditions – a sour soundtrack, a muted lemon video showing a man eating a lemon, and a silent baseline condition. The results revealed that salivation during the lemon video condition was significantly greater than in the sour soundtrack and baseline conditions. However, contrary to our hypothesis, there was no significant difference between salivation levels in the sour soundtrack compared to the baseline condition. These results are discussed in terms of potential mechanisms underlying the auditory modulation of taste perception/evaluation. PMID:28491044

  1. REPEATED MEASURES ANALYSIS OF CHANGES IN PHOTOSYNTHETIC EFFICIENCY IN SOUR CHERRY DURING WATER DEFICIT

    Directory of Open Access Journals (Sweden)

    Marija Viljevac

    2012-06-01

    Full Text Available The objective of this study was to investigate changes in photosynthetic efficiency applying repeated measures ANOVA using the photosynthetic performance index (PIABS of the JIP-test as a vitality parameter in seven genotypes of sour cherry (Prunus cerasus, L. during 10 days of continuous water deficit. Both univariate and multivariate ANOVA repeated measures revealed highly significant time effect (Days and its subsequent interactions with genotype and water deficit. However, the multivariate Pillai’s trace test detected the interaction Time × Genotype × Water deficit as not significant. According to the Tukey’s Studentized Range (HSD test, differences between the control and genotypes exposed to water stress became significant on the fourth day of the experiment, indicating that the plants on the average, began to lose their photosynthetic efficiency four days after being exposed to water shortage. It corroborates previous findings in other species that PIABS is very sensitive tool for detecting drought stress.

  2. Producer observations of the long term effects of acid forming emissions in livestock

    International Nuclear Information System (INIS)

    McGlynn, D.

    1992-01-01

    A series of interviews with livestock producers is presented to illustrate the environmental problems caused by sour gas plants in the Pincher Creek area of Alberta. Farmers located in the emission plume from the Shell Waterton plant and Gulf sour gas plants were interviewed and provided anecdotal evidence of adverse impacts of sour gas plant emissions on livestock. Common problems that are noticed in livestock include eye irritation, increased respiratory infections, mineral deficiencies, eye cancer, waterhole water quality deterioration, low calf birth weights, decreased cattle weight gain, and birth defects. Crop losses, lowered grass production, machinery corrosion, and water pollution also occur. 1 fig

  3. Music to Make Your Mouth Water? Assessing the Potential Influence of Sour Music on Salivation

    Directory of Open Access Journals (Sweden)

    Qian J. Wang

    2017-04-01

    Full Text Available People robustly associate various sound attributes with specific smells/tastes, and soundtracks that are associated with specific tastes can influence people’s evaluation of the taste of food and drink. However, it is currently unknown whether such soundtracks directly impact the eating experience via physiological changes (an embodiment account, or whether they act at a higher cognitive level, or both. The present research assessed a version of the embodiment account, where a soundtrack associated with sourness is hypothesized to induce a physiological response in the listener by increasing salivary flow. Salivation was measured while participants were exposed to three different experimental conditions – a sour soundtrack, a muted lemon video showing a man eating a lemon, and a silent baseline condition. The results revealed that salivation during the lemon video condition was significantly greater than in the sour soundtrack and baseline conditions. However, contrary to our hypothesis, there was no significant difference between salivation levels in the sour soundtrack compared to the baseline condition. These results are discussed in terms of potential mechanisms underlying the auditory modulation of taste perception/evaluation.

  4. Corrosion inhibitor development for slightly sour environments with oxygen intrusion

    Energy Technology Data Exchange (ETDEWEB)

    Wylde, J.; Wang, H.; Li, J. [Clariant Oil Services North America, Calgary, AB (Canada)

    2009-07-01

    This presentation reported on a study that examined the effect of oxygen on the inhibition of carbon steel in slightly sour corrosion, and the initiation and propagation of localized attack. Oxygen can enter sour water injection systems through the vapor space in storage tanks and process system. Oxygen aggravates the corrosion attack by participating in the cathodic reaction under full or partial diffusion control. Laboratory testing results were reported in this presentation along with the development of corrosion inhibitors for such a slightly sour system. Bubble testing cells were used with continuous H{sub 2}/CO{sub 2} mixture gas sparging and occasional oxygen intrusion of 2 to 4 hours during a week long test. Linear polarization resistance (LPR) measurements and weight loss corrosion coupons were used to quantify the corrosion attack. The findings were presented in terms of the magnitude of localized attacks at different oxygen concentrations and intrusion periods, with and without the presence of corrosion inhibitors. tabs., figs.

  5. Nature of local benefits to communities impacted by sour gas development : Public safety and sour gas recommendation 79 : Final report

    International Nuclear Information System (INIS)

    2003-09-01

    The Provincial Advisory Committee on Public Safety and Sour Gas of Alberta issued a report in December 2002, in which recommendations were made on how to improve the sour gas regulatory system and reduce the impacts of sour gas on public safety and health. Recommendation 79 of this report called for a study to determine the nature of local benefits such as property taxes and local business opportunities, to communities affected by sour gas development. The present document was prepared by a multi-stake holder committee consisting of representatives from municipal government, academia, industry associations, the provincial government, and the public. One of its objectives was to identify matters of importance to stake holders concerning the study. The committee examined three major areas: economic benefit, net financial benefit to municipalities, and impact of sour gas development on local residents. The results indicated that the province and municipalities in which sour gas activities take place benefit from these activities. All Albertans benefit somewhat, and those living in areas where the sour gas industry operates might benefit through employment or the net benefit accrued to municipal government. A detailed quantification of local benefits at the municipal level for individuals was provided in this document. A full accounting of costs or negative impacts that may affect some individuals was not provided. refs., 6 tabs

  6. Sour ageusia in two individuals implicates ion channels of the ASIC and PKD families in human sour taste perception at the anterior tongue.

    Directory of Open Access Journals (Sweden)

    Taufiqul Huque

    2009-10-01

    Full Text Available The perception of sour taste in humans is incompletely understood at the receptor cell level. We report here on two patients with an acquired sour ageusia. Each patient was unresponsive to sour stimuli, but both showed normal responses to bitter, sweet, and salty stimuli.Lingual fungiform papillae, containing taste cells, were obtained by biopsy from the two patients, and from three sour-normal individuals, and analyzed by RT-PCR. The following transcripts were undetectable in the patients, even after 50 cycles of amplification, but readily detectable in the sour-normal subjects: acid sensing ion channels (ASICs 1a, 1beta, 2a, 2b, and 3; and polycystic kidney disease (PKD channels PKD1L3 and PKD2L1. Patients and sour-normals expressed the taste-related phospholipase C-beta2, the delta-subunit of epithelial sodium channel (ENaC and the bitter receptor T2R14, as well as beta-actin. Genomic analysis of one patient, using buccal tissue, did not show absence of the genes for ASIC1a and PKD2L1. Immunohistochemistry of fungiform papillae from sour-normal subjects revealed labeling of taste bud cells by antibodies to ASICs 1a and 1beta, PKD2L1, phospholipase C-beta2, and delta-ENaC. An antibody to PKD1L3 labeled tissue outside taste bud cells.These data suggest a role for ASICs and PKDs in human sour perception. This is the first report of sour ageusia in humans, and the very existence of such individuals ("natural knockouts" suggests a cell lineage for sour that is independent of the other taste modalities.

  7. Effects of a sour bolus on the intramuscular electromyographic (EMG) activity of muscles in the submental region.

    Science.gov (United States)

    Palmer, Phyllis M; McCulloch, Timothy M; Jaffe, Debra; Neel, Amy T

    2005-01-01

    A sour bolus has been used as a modality in the treatment of oropharyngeal dysphagia based on the hypothesis that this stimulus provides an effective preswallow sensory input that lowers the threshold required to trigger a pharyngeal swallow. The result is a more immediate swallow onset time. Additionally, the sour bolus may invigorate the oral muscles resulting in stronger contractions during the swallow. The purpose of this investigation was to compare the intramuscular electromyographic activity of the mylohyoid, geniohyoid, and anterior belly of the digastric muscles during sour and water boluses with regard to duration, strength, and timing of muscle activation. Muscle duration, swallow onset time, and pattern of muscle activation did not differ for the two bolus types. Muscle activation time was more tightly approximated across the onsets of the three muscles when a sour bolus was used. A sour bolus also resulted in a stronger muscle contraction as evidenced by greater electromyographic activity. These data support the use of a sour bolus as part of a treatment paradigm.

  8. SOUR MILK FORMULAS IN NUTRITION OF INFANTS

    Directory of Open Access Journals (Sweden)

    E.F. Lukushkina

    2010-01-01

    Full Text Available Health-giving properties of fermented food are related to the fact, that acid medium improves assimilation of protein and fat, increases absorption of iron and zinc, improves digestion. But the kefir and other sour milk food based on the whole milk can’t be used in nutrition of infants as human milk substitute because of high content of protein, high osmolarity, deficiency of vitamins and microelements. The article describes the results of clinical approbation of new modern sour milk formula «NAN sour milk», containing proper amount of high-quality protein (OptiPro, enriched with lactalbumin and all sufficient vitamins and microelements. This mixture contains also probiotics (B. lactis, providing high functionality of this food. Key words: infants, sour milk formula, nutrition.(Voprosy sovremennoi pediatrii — Current Pediatrics. 2010;9(1:136-141

  9. Bortezomib alters sour taste sensitivity in mice

    Directory of Open Access Journals (Sweden)

    Akihiro Ohishi

    Full Text Available Chemotherapy-induced taste disorder is one of the critical issues in cancer therapy. Bortezomib, a proteasome inhibitor, is a key agent in multiple myeloma therapy, but it induces a taste disorder. In this study, we investigated the characteristics of bortezomib-induced taste disorder and the underlying mechanism in mice. Among the five basic tastes, the sour taste sensitivity of mice was significantly increased by bortezomib administration. In bortezomib-administered mice, protein expression of PKD2L1 was increased. The increased sour taste sensitivity induced by bortezomib returned to the control level on cessation of its administration. These results suggest that an increase in protein expression of PKD2L1 enhances the sour taste sensitivity in bortezomib-administered mice, and this alteration is reversed on cessation of its administration. Keywords: Taste disorder, Bortezomib, Sour taste, Chemotherapy, Adverse effect

  10. SOUR MILK FOODSTUFF IN INFANTS DIET

    Directory of Open Access Journals (Sweden)

    T. E. Borovik

    2014-01-01

    Full Text Available Products of sour milk are widely used in nutrition of infants. They are an important source of digestible proteins, vitamins and potassium. Regular intake of sour milk foodstuff has favorable influence on intestinal microbiocenosis, functioning of the immune system, improves secretory and motor functions of the gastrointestinal tract, stimulates appetites and increases bioavailability of micronutrients. Modern line in functional diet is enrichment of sour milk foodstuff with probiotics. Strains of microorganisms used in manufacture of products with probiotic action are proven to be safe and effective in prophylaxis and treatment of various diseases. Modern data which confirm prophylactic and medicinal properties of probiotic-containing foodstuff, especially bioyoghurts for children, are shown in this article.

  11. Evaluation of maize-soybean flour blends for sour maize bread ...

    African Journals Online (AJOL)

    Properties examined included amylose content, bulk density, dispersibility, swelling power, water absorption capacity and viscoelastic properties. The effect of the different flour/meal samples on the properties of sour maize bread were evaluated by baking bread samples with the different flours/meals using a mixed starter ...

  12. Advanced oxidation processes for treatment of petroleum refinery sour waters; Processos oxidativos avancados para tratamento de aguas acidas de refinaria de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Castro, Antonio V.; Coelho, Alessandra D.; Sant' Anna Junior, Geraldo L.; Dezotti, Marcia [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Programa de Engenharia Quimica

    2004-07-01

    The characteristics of the waste water generated by the petroleum refineries are related to the type and amount of processed oil, to the nature and the efficiency of the refining operation. The effluents are composed basically of oily waters, originating from of the contact with the oil. Among them, the current of sour water is one of the most preoccupying due to its composition: sulfide, ammonia, mercaptans, phenol, dissolved oil, basic pH, dissolved organic carbon (DOC) and chemical oxygen demand (COD) high. The aim of this work was to evaluate the advanced oxidation processes to degrade sour water (UV radiation, H{sub 2}O{sub 2} and H{sub 2}O{sub 2}/UV, photocatalysis, Fenton and photo-Fenton). All process, except Fenton and photo-Fenton, did not supply satisfactory results, reducing 25% of initial DOC, which it is of 450 mg/L. The results using the Fenton process reached removal of 50% of the initial COD, and when photo- Fenton process obtaining removal of 90%. The processes Fenton and photo-Fenton were shown capable to degrade this kind of waste water, minimizing the environmental problems and corrosion, operating as a pre-treatment for the biological system, or acting alone to degrade the organic matter contained, seeking the water reuse. The effluent used in this work came from Duque de Caxias Refinery (Reduc)/PETROBRAS. (author)

  13. Reservoir Souring - Latest developments for application and mitigation

    DEFF Research Database (Denmark)

    Johnson, Richard J; Folwell, Benjamin D; Wirekoh, Alexander

    2017-01-01

    Sulphate-reducing prokaryotes (SRP) have been identified in oil field fluids since the 1920s. SRP reduce sulphate to sulphide, a toxic and corrosive species that impacts on operational safety, metallurgy and both capital and operational cost. Differences in water cut, temperature, pressure...... and fluid chemistry can impact on the observed H2S concentration, meaning that an increase in H2S concentration does not always correlate with activity of SRP. However it wasn't until the 1990s that SRP activity was accepted as the leading cause of reservoir souring (i.e. an increase in H2S concentrations...... to reservoir souring. This has led to some recent advances in microbial control and detection, however, despite this, many of the methods used routinely for microbial control and detection are over a century old. We therefore look towards emerging and novel mitigation technologies that may be used...

  14. Evaluation and improvement of sour property packages in UniSim design

    Energy Technology Data Exchange (ETDEWEB)

    Yang, J.; Zhao, E.; Wang, L.; Saha, S. [Honeywell, Calgary, AB (Canada)

    2010-07-01

    This presentation described specialty fluid packages for modeling oil and gas process systems involving sour gases in contact with aqueous phase. UniSim Design is a popular process simulation tool in the oil and gas industry. The sour Peng-Robinson (PR) and sour Soave-Redlich-Kwong (SRK) models are commonly used for handling sour system where hydrogen sulphide (H{sub 2}S), carbon dioxide (CO{sub 2}) or ammonia (NH{sub 3}) are in contact with an aqueous phase. These sour options combine the PR/SRK equation of state and Wilson's API-sour model where the equation of state is used to determine the fugacities of the vapor and liquid hydrocarbon phases, plus the enthalpy for all 3 phases. The Wilson's API-sour method is used for the aqueous phase calculations, which accounts for the ionization of H{sub 2}S, CO{sub 2} and NH{sub 3} in the aqueous phase. The efficiency of these 2 thermodynamic property packages were evaluated in this study by comparing industrial and experimental data and the results from other similar models. The purpose of this study was to improve these property packages for more accurate and reliable modeling of sour systems. tabs., figs.

  15. Radical scavenging activities of Rio Red grapefruits and Sour orange fruit extracts in different in vitro model systems.

    Science.gov (United States)

    Jayaprakasha, G K; Girennavar, Basavaraj; Patil, Bhimanagouda S

    2008-07-01

    Antioxidant fractions from two different citrus species such as Rio Red (Citrus paradise Macf.) and Sour orange (Citrus aurantium L.) were extracted with five different polar solvents using Soxhlet type extractor. The total phenolic content of the extracts was determined by Folin-Ciocalteu method. Ethyl acetate extract of Rio Red and Sour orange was found to contain maximum phenolics. The dried fractions were screened for their antioxidant activity potential using in vitro model systems such as 1,1-diphenyl-2-picryl hydrazyl (DPPH), phosphomolybdenum method and nitroblue tetrazolium (NBT) reduction at different concentrations. The methanol:water (80:20) fraction of Rio Red showed the highest radical scavenging activity 42.5%, 77.8% and 92.1% at 250, 500 and 1000 ppm, respectively, while methanol:water (80:20) fraction of Sour orange showed the lowest radical scavenging activity at all the tested concentrations. All citrus fractions showed good antioxidant capacity by the formation of phosphomolybdenum complex at 200 ppm. In addition, superoxide radical scavenging activity was assayed using non-enzymatic (NADH/phenaxine methosulfate) superoxide generating system. All the extracts showed variable superoxide radical scavenging activity. Moreover, methanol:water (80:20) extract of Rio Red and methanol extract of Sour orange exhibited marked reducing power in potassium ferricyanide reduction method. The data obtained using above in vitro models clearly establish the antioxidant potential of citrus fruit extracts. However, comprehensive studies need to be conducted to ascertain the in vivo bioavailability, safety and efficacy of such extracts in experimental animals. To the best of our knowledge, this is the first report on antioxidant activity of different polar extracts from Rio Red and Sour oranges.

  16. De novo transcriptome assembly of a sour cherry cultivar, Schattenmorelle

    Directory of Open Access Journals (Sweden)

    Yeonhwa Jo

    2015-12-01

    Full Text Available Sour cherry (Prunus cerasus in the genus Prunus in the family Rosaceae is one of the most popular stone fruit trees worldwide. Of known sour cherry cultivars, the Schattenmorelle is a famous old sour cherry with a high amount of fruit production. The Schattenmorelle was selected before 1650 and described in the 1800s. This cultivar was named after gardens of the Chateau de Moreille in which the cultivar was initially found. In order to identify new genes and to develop genetic markers for sour cherry, we performed a transcriptome analysis of a sour cherry. We selected the cultivar Schattenmorelle, which is among commercially important cultivars in Europe and North America. We obtained 2.05 GB raw data from the Schattenmorelle (NCBI accession number: SRX1187170. De novo transcriptome assembly using Trinity identified 61,053 transcripts in which N50 was 611 bp. Next, we identified 25,585 protein coding sequences using TransDecoder. The identified proteins were blasted against NCBI's non-redundant database for annotation. Based on blast search, we taxonomically classified the obtained sequences. As a result, we provide the transcriptome of sour cherry cultivar Schattenmorelle using next generation sequencing.

  17. Using Thermodynamics to Predict the Outcomes of Nitrate-Based Oil Reservoir Souring Control Interventions

    Directory of Open Access Journals (Sweden)

    Jan Dolfing

    2017-12-01

    Full Text Available Souring is the undesirable production of hydrogen sulfide (H2S in oil reservoirs by sulfate-reducing bacteria (SRB. Souring is a common problem during secondary oil recovery via water flooding, especially when seawater with its high sulfate concentration is introduced. Nitrate injection into these oil reservoirs can prevent and remediate souring by stimulating nitrate-reducing bacteria (NRB. Two conceptually different mechanisms for NRB-facilitated souring control have been proposed: nitrate-sulfate competition for electron donors (oil-derived organics or H2 and nitrate driven sulfide oxidation. Thermodynamics can facilitate predictions about which nitrate-driven mechanism is most likely to occur in different scenarios. From a thermodynamic perspective the question “Which reaction yields more energy, nitrate driven oxidation of sulfide or nitrate driven oxidation of organic compounds?” can be rephrased as: “Is acetate driven sulfate reduction to sulfide exergonic or endergonic?” Our analysis indicates that under conditions encountered in oil fields, sulfate driven oxidation of acetate (or other SRB organic electron donors is always more favorable than sulfide oxidation to sulfate. That predicts that organotrophic NRB that oxidize acetate would outcompete lithotrophic NRB that oxidize sulfide. However, sulfide oxidation to elemental sulfur is different. At low acetate HS− oxidation is more favorable than acetate oxidation. Incomplete oxidation of sulfide to S0 is likely to occur when nitrate levels are low, and is favored by low temperatures; conditions that can be encountered at oil field above-ground facilities where intermediate sulfur compounds like S0 may cause corrosion. These findings have implications for reservoir management strategies and for assessing the success and progress of nitrate-based souring control strategies and the attendant risks of corrosion associated with souring and nitrate injection.

  18. Control of degreening in postharvest green sour citrus fruit by electrostatic atomized water particles.

    Science.gov (United States)

    Yamauchi, Naoki; Takamura, Kohtaro; Shigyo, Masayoshi; Migita, Catharina Taiko; Masuda, Yukihiro; Maekawa, Tetsuya

    2014-08-01

    The effect of electrostatic atomized water particles (EAWP) on degreening of green sour citrus fruit during storage was determined. Superoxide anion and hydroxyl radicals included in EAWP were present on the surface of the fruit peel after the treatment. Hydrogen peroxide was formed from EAWP in an aqueous solution, which could indicate that a hydroxyl radical of EAWP turns to hydrogen peroxide in the fruit flavedo as well as in the aqueous solution. EAWP treatment effectively suppressed the degreening of green yuzu and Nagato-yuzukichi fruits during storage at 20°C. The enhancement in K+ ion leakage of both EAWP-treated fruits reduced in comparison with the control. In spite of EAWP treatment, total peroxide level in both fruits showed almost no changes during storage, suggesting that hydrogen peroxide formed by EAWP treatment could stimulate the activation of hydrogen peroxide scavenging system and control degreening of these fruits during storage. Copyright © 2014 Elsevier Ltd. All rights reserved.

  19. Sour Taste preferences of children relate to preference of novel and intense stimuli

    NARCIS (Netherlands)

    Liem, D.G.; Westerbeek, A.; Wolterink, S.; Kok, F.J.; Graaf, de C.

    2004-01-01

    Previous research has suggested that some children have a preference for sour tastes. The origin of this preference remains unclear. We investigated whether preference for sour tastes is related to a difference in rated sour intensity due to physiological properties of saliva, or to an overall

  20. Case studies of the application of enhanced steel alloys for bottom hole assembly components for sour service conditions

    Energy Technology Data Exchange (ETDEWEB)

    Chan, Alvaro [Nov Grant Prideco, Navasota (United States); Moura, Carlos [ASPEN Assesoria Tecnica e Comercial, Cascavel, PR (Brazil); Johnson, Charles; Landriault, Alain [Weatherford Canda Partnership, Calgary, AB (Canada)

    2008-07-01

    The new more modern drilling programs require the drill string to travel across sour formations in order to reach the hydrocarbon reservoirs. Traditional materials have been employed in the manufacture of HWDP components along with basic heat treatment processes. Standard HWDP tools have started to show their operational as well as environmental limitations when subjected to sour service applications. The advanced, more complex drilling programs require for the HWDP tools to be put in service under different configurations. Either at the bottom of the drill string near the drill bit for vertical well configurations or on top of the drill string for weight application on horizontal or extended reach applications. An operator in northwestern Canada has replaced standard HWDP with enhanced sour service HWDP in order to complete the programmed wells. These enhanced tools offer higher tensile and torque capabilities and improved toughness than standard HWDP tools and in addition, provide protection against sour service conditions. The use of second-generation double shoulder connections (2nd-Gen. DSC) has also provided added torque and tensile capacities to these versatile HWDP tools. For over a year more than a dozen wells have been drilled employing these enhanced BHA tools and have helped the operator reach its targets through sour service formations and produce wells in a safe and cost effective manner. (author)

  1. Industrial processing effects on phenolic compounds in sour cherry (Prunus cerasus L.) fruit

    NARCIS (Netherlands)

    Toydemir, G.; Capanoglu, E.; Gomez-Roldan, M.V.; Vos, de R.C.H.; Boyacioglu, D.; Hall, R.D.; Beekwilder, M.J.

    2013-01-01

    The processed juice (or nectar) of the sour cherry, Prunus cerasus L., is widely consumed in the Balkan region and Turkey. Sour cherry is known to be rich in polyphenolic compounds, such as anthocyanins and procyanidins. In this work, the effects of processing of sour cherry fruit to nectar on

  2. Modelling souring in a high salinity reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Adams, Michael; Crossland, Alan; Stott, Jim

    2006-03-15

    CAPCIS Ltd (Capcis) have developed a souring model for use in highly saline reservoirs where salinity limits the growth of sulphate reducing bacteria (SRB). Capcis have successfully applied the model to a field in North Africa. The conceptual basis of the model considers the course of the H2S from generation in the reservoir including dilution, sulphide retardation and scavenging and H2S fluid phase partitioning. At each stage mathematical equations governing the behaviour of the H2S were produced. In order to estimate the potential for H2S generation, it is required to know the chemistry of the injection and formation waters, as well as the properties of the indigenous SRB, i.e. the maximum salinity for their growth. This is determined by bottle testing of H2S generation by SRB at a range of injection/formation water ratios. The maximum salinity for SRB growth then determines the mixing ratios at which H2S generation takes place. Sulphide retardation due to adsorption at immobile interfaces was empirically modeled from reservoir data. Sulphide scavenging due to reaction with iron generated from corrosion was also modelled. Reservoir mineral scavenging was not modelled but could be incorporated in an extension to the model. Finally, in order to compute the gas-phase concentration of generated H2S, the H2S in the well stream is partitioned between the gas, oil and water phases. Capcis has carried out detailed computations of H2S solubility in crude oil and formation waters and the derivation of distribution ratios based on the respective partition coefficients using Gerard's line method, a modification of Henry's Law. (author) (tk)

  3. Public safety and sour gas quarterly progress report October - December 2002

    Energy Technology Data Exchange (ETDEWEB)

    Sikora, V.; Lillo, H.; Craig, M.; Neilson, G.

    2003-01-01

    This third quarterly progress report for the business year 2002-2003 on the Alberta Energy and Utilities Board (EUB) Public Safety and Sour Gas initiative covers projects based on the 87 recommendations made by the Provincial Advisory Committee on Public Safety and Sour Gas (Advisory Committee) in December 2000. As of December 2002, work has been completed on 16 recommendations and is proceeding on 50 recommendations. This report includes several tables indicating the status of recommendations as either complete or ongoing. The recommendation categories include: (1) sour gas development, planning and approval, (2) sour gas operations, (3) emergency preparedness, and (4) information, communication and consultation. The report also summarizes the health effects and sour gas research. Recommendations completed as of December 2002 include: plant proliferation; pre-license review of critical well license applications; license application training/certification information requirement; increase sour gas inspections; increase inspections of new and noncompliant operators; implement 100 per cent inspection rate for critical wells near people; response to sour gas complaints; enhance EUB capability to monitor for complaint response/compliance; complaint/incident response program for Aboriginal communities; interim policy on ERP review and reduced EPZs; infrastructure and resources for Aboriginal community ERP; field staff in industry-landowner discussions; EUB involvement in mediation of application issues; and, timely and meaningful public consultation for First Nations and Metis. Alberta Health and Wellness is currently evaluating the health effects of H{sub 2}S and SO{sub 2} and the work is near completion. Other ongoing work includes the development of a draft protocol to address the involvement of regional health authorities (RHAs), the early involvement of RHAs and other local government bodies, and a process for communication between the EUB field staff and

  4. 27 CFR 25.192 - Removal of sour or damaged beer.

    Science.gov (United States)

    2010-04-01

    ... beer. 25.192 Section 25.192 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS BEER Removals Without Payment of Tax Removal of Beer Unfit for Beverage Use § 25.192 Removal of sour or damaged beer. (a) Containers. The brewer shall remove sour or...

  5. Antihyperlipidemic Effects of Sour Cherries Characterized by Different In Vitro Antioxidant Power and Polyphenolic Composition.

    Science.gov (United States)

    Papp, Nóra; Blázovics, Anna; Fébel, Hedvig; Salido, Sofía; Altarejos, Joaquín; Fehér, Erzsébet; Kocsis, Ibolya; Szentmihályi, Klára; Abrankó, László; Hegedűs, Attila; Stefanovits-Bányai, Éva

    2015-12-01

    The aims of the present study were to clarify in vivo effects of three sour cherry cultivars characterized by different polyphenolic composition in hyperlipidemic animals in a short term experiment. The three different sour cherry cultivars were chosen based on their total in vitro antioxidant capacity, total polyphenolic, monomeric anthocyanin and flavonoid content. Male Wistar rats were divided randomly into eight groups: rats kept on normal diet (control) and normal diet supplied with sour cherry powder of one of the three cultivars; others were kept on fat-rich diet and fat-rich diet supplied with sour cherry powder prepared from one of the three cultivars. The treatment lasted 10 days. Lyophilized sour cherry administered in the diet decreased both total cholesterol and LDL cholesterol levels, and increased the HDL cholesterol concentration in sera of hyperlipidemic animals. Significant differences were found in the efficacy of different sour cherry cultivars in case of hyperlipidemia. Sour cherries characterized by higher polyphenol content seem to have a more pronounced effect on serum cholesterol levels. Our results suggest that besides anthocyanins, colourless polyphenols also have lipid lowering effect.

  6. Effect of adding sour yoghurt and dough as bacterial inoculant on ...

    African Journals Online (AJOL)

    Inoculation of whole-crop corn with sourdough and sour yoghurt significantly decreased pH, ash content and ammonia nitrogen, while dry matter determined using toloen distillation (DMT), Flieg point, crude protein (CP), and total nitrogen increased (P<0.05). Key words: Silage, sour yoghurt, sourdough, corn forage.

  7. Advanced technologies for manufacturing high strength sour grade UOE line pipe

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, Kenji; Omura, Tomohiko; Takahashi, Nobuaki; Minato, Izuru; Yamamoto, Akio [Sumitomo Metal Industries, Ltd., Kashima, (Japan)

    2010-07-01

    A new kind of high strength pipeline has been manufactured for sour service in offshore pipelines. This paper first presents a review of developments in manufacturing technology to improve sour resistance. This was particularly the case with Grade UOE line pipe. The improvement was achieved by optimizing the continuous casting process, monitoring the shape of inclusions (such as MnS, CaS, Al2O3, CaO-Al2O3) and decreasing coarse precipitates (Nb(C,N), TiN). The study then used the HIC evaluation method to determine hydrogen induced cracking (HIC) resistance of the material and HAZ test for sulfide stress cracking (SSC) resistance. The evaluation of the NACE TM0284 solution A showed that these pipelines are able to resist severe sour conditions because of good HIC and SSC resistance. Optimizing others components like alloying elements and the ACC process would improve sour resistance in future applications.

  8. Numerical simulation of a sour gas flare

    Energy Technology Data Exchange (ETDEWEB)

    Chambers, A. [Alberta Research Council, Devon, AB (Canada)

    2008-07-01

    Due to the limited amount of information in the literature on sour gas flares and the cost of conducting wind tunnel and field experiments on sour flares, this presentation presented a modelling project that predicted the effect of operating conditions on flare performance and emissions. The objectives of the project were to adapt an existing numerical model suitable for flare simulation, incorporate sulfur chemistry, and run simulations for a range of conditions typical of sour flares in Alberta. The study involved the use of modelling expertise at the University of Utah, and employed large eddy simulation (LES) methods to model open flames. The existing model included the prediction of turbulent flow field; hydrocarbon reaction chemistry; soot formation; and radiation heat transfer. The presentation addressed the unique features of the model and discussed whether LES could predict the flow field. Other topics that were presented included the results from a University of Utah comparison; challenges of the LES model; an example of a run time issue; predicting the impact of operating conditions; and the results of simulations. Last, several next steps were identified and preliminary results were provided. Future work will focus on reducing computation time and increasing information reporting. figs.

  9. Some effects of winter grazing of Dohne sour veld | PF | African ...

    African Journals Online (AJOL)

    The utilisation of spared sour veld poses practical problems. As a result of the development of high level protein or nitrogen supplements it has however become possible to efficiently graze spared veld. Results of experiments during three winters where spared sour veld was grazed off either by sheep or by cattle are given.

  10. A Multistage Fluidized Bed for the Deep Removal of Sour Gases : Proof of Concept and Tray Efficiencies

    NARCIS (Netherlands)

    Driessen, Rick T.; Bos, Martin J.; Brilman, Derk W. F.

    2018-01-01

    Currently there are significant amounts of natural gas that cannot be produced and treated to meet pipeline specifications, because that would not be economically viable. This work investigates a bench scale multistage fluidized bed (MSFB) with shallow beds for sour gas removal from natural gas

  11. SUBSTANTIATION OF STORAGE PARAMETERS OF THE SOUR-MILK INFANT DRINK «BIOLAKT»

    Directory of Open Access Journals (Sweden)

    N. Tkachenko

    2017-10-01

    Full Text Available Changes in the quality indicators of sour-milk infant drink «Biolakt» characterized by high probiotic and immunomodulatory properties and low allergic effect that were made according to the improved technology and stored in sealed-off containers at temperature (4±2 ºС during 28 days have been studied: organoleptic properties of taste and odour, consistency and appearance; physical and chemical properties – titrated acidity, ºТ; active acidity, pH units; moisture retention property, %; microbiological properties – number of living cells of mixed cultures B. bifidum 1 + B. longum Я3 + B. infantis 512, CFU/cm3; the most probable number of living cells of monocultures L. acidophilus La-5, CFU/cm3; presence of coli form bacteria in 0.3 cm3; presence of  Salmonella in 50 cm3; biochemical properties – antioxidant activity, activity units; and maximum possible content of malondialdehyde at complete oxidation of the product ingredients, mg/100 g. It is proved that under indicated conditions in the course of 24 days the studied samples of target products possess high organoleptic and standardized for sour-milk infant drinks physical, chemical, biochemical and microbiological indicators and are, also, characterized by high content of probiotics: (0.43…8.60∙109 and (0.25…1.10∙109 CFU/cm3 of living cells of bifidus bacteria and lactobacilli, accordingly.It has been established that the limit storage period of sour-milk infant drink «Biolakt» produced according to the improved technology and stored at temperature (4±2 ºС should not exceed 12 days with due account of the safety margin for sour-milk infant drinks (provided they are kept in sealed-off containers.It has been proved that the target product formulas should include lactulose, polyunsaturated fatty acids omega-3 FT EU of «Fortitech» company (Denmark, vitamin complex FT 041081EU of «Fortitech» company (Denmark and/or complex of mineral substances FT 042836EU of

  12. Reação da laranjeira azêda à tristeza Reaction of the sour orange plant to tristeza

    Directory of Open Access Journals (Sweden)

    A. S. Costa

    1954-01-01

    orange onsour orange rootstock show phloem degeneration when the plant is affected with tristeza. These degeneration symptoms have been used to distinguish tristeza disease from other decline diseases that affect the same stock-scion combination. Over 45 varieties of sour oranges have been tried as rootstocks for tristeza infected sweet orange tops and they all behaved as non-tolerant rootstocks. So far no tristeza tolerant sour orange rootstock is known, but it seems entirely possible that crosses between sour orange and tristeza-tolerant citrus varieties may yield F1 hydrids that combine the desirable characteristics of the sour orange rootstock with tristeza tolerant tissues. In case such an F1 hybrid produced large number of nucellar seedlings these could be used as rootstocks. Sour orange varieties can be used as rootstocks for commercial acid lemons or sour orange tops even in areas where tristeza is present. There is as slight possibility that if a somewhat tolerant sour orange is found, it might be used a3 rootstock for grapefruits, sweet orange, mandarin, and other tristeza susceptible tops if complementary controlling measures are employed such as protective inoculation of the scion with mild strains of the virus, use of multiple bud union, etc. Tests have shown that buds from a single budstick taken from a tristeza infected sour orange plant may produce healthy and diseased tops when budded on a sour orange rootstock, thus indicating that tristeza virus was not present in all buds of the infected plant. It has been observed that commercial acid lemon and sour orange buds make satisfactory growth when top worked on tristeza-diseased sweet orange tops on sour orange rootstocks. Attempts have been made to control tristeza disease in sweet orange on sour orange rootstock by inducing the rootstock to develop sprouts and thus produce a sour orange top that would supply sinthates for the roots. The presence of this composite sweet orange and sour orange top may be of

  13. Efficacy of gaseous ozone to counteract postharvest table grape sour rot.

    Science.gov (United States)

    Pinto, L; Caputo, L; Quintieri, L; de Candia, S; Baruzzi, F

    2017-09-01

    This work aims at studying the efficacy of low doses of gaseous ozone in postharvest control of the table grape sour rot, a disease generally attributed to a consortium of non-Saccharomyces yeasts (NSY) and acetic acid bacteria (AAB). Sour rot incidence of wounded berries, inoculated with 8 NSYstrains, or 7 AAB, or 56 yeast-bacterium associations, was monitored at 25 °C up to six days. Sour rot incidence in wounded berries inoculated with yeast-bacterium associations resulted higher than in berries inoculated with one single NSY or AAB strain. Among all NSY-AAB associations, the yeast-bacterium association composed of Candida zemplinina CBS 9494 (Cz) and Acetobacter syzygii LMG 21419 (As) showed the highest prevalence of sour rot; thus, after preliminary in vitro assays, this simplified As-Cz microbial consortium was inoculated in wounded berries that were stored at 4 °C for ten days under ozone (2.14 mg m -3 ) or in air. At the end of cold storage, no berries showed sour-rot symptoms although ozonation mainly affected As viable cell count. After additional 12 days at 25 °C, the sour rot index of inoculated As-Cz berries previously cold-stored under ozone or in air accounted for 22.6 ± 3.7% and 66.7 ± 4.5%, respectively. Molecular analyses of dominant AAB and NSY populations of both sound and rotten berries during post-refrigeration period revealed the appearance of new strains mainly belonging to Gluconobacter albidus and Hanseniaspora uvarum species, respectively. Cold ozonation resulted an effective approach to extend the shelf-life of table grapes also after cold storage. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Genetic Diversity Assessment and Identification of New Sour Cherry Genotypes Using Intersimple Sequence Repeat Markers

    Directory of Open Access Journals (Sweden)

    Roghayeh Najafzadeh

    2014-01-01

    Full Text Available Iran is one of the chief origins of subgenus Cerasus germplasm. In this study, the genetic variation of new Iranian sour cherries (which had such superior growth characteristics and fruit quality as to be considered for the introduction of new cultivars was investigated and identified using 23 intersimple sequence repeat (ISSR markers. Results indicated a high level of polymorphism of the genotypes based on these markers. According to these results, primers tested in this study specially ISSR-4, ISSR-6, ISSR-13, ISSR-14, ISSR-16, and ISSR-19 produced good and various levels of amplifications which can be effectively used in genetic studies of the sour cherry. The genetic similarity among genotypes showed a high diversity among the genotypes. Cluster analysis separated improved cultivars from promising Iranian genotypes, and the PCoA supported the cluster analysis results. Since the Iranian genotypes were superior to the improved cultivars and were separated from them in most groups, these genotypes can be considered as distinct genotypes for further evaluations in the framework of breeding programs and new cultivar identification in cherries. Results also confirmed that ISSR is a reliable DNA marker that can be used for exact genetic studies and in sour cherry breeding programs.

  15. 5-HT3A -driven green fluorescent protein delineates gustatory fibers innervating sour-responsive taste cells: A labeled line for sour taste?

    Science.gov (United States)

    Stratford, J M; Larson, E D; Yang, R; Salcedo, E; Finger, T E

    2017-07-01

    Taste buds contain multiple cell types with each type expressing receptors and transduction components for a subset of taste qualities. The sour sensing cells, Type III cells, release serotonin (5-HT) in response to the presence of sour (acidic) tastants and this released 5-HT activates 5-HT 3 receptors on the gustatory nerves. We show here, using 5-HT 3A GFP mice, that 5-HT 3 -expressing nerve fibers preferentially contact and receive synaptic contact from Type III taste cells. Further, these 5-HT 3 -expressing nerve fibers terminate in a restricted central-lateral portion of the nucleus of the solitary tract (nTS)-the same area that shows increased c-Fos expression upon presentation of a sour tastant (30 mM citric acid). This acid stimulation also evokes c-Fos in the laterally adjacent mediodorsal spinal trigeminal nucleus (DMSp5), but this trigeminal activation is not associated with the presence of 5-HT 3 -expressing nerve fibers as it is in the nTS. Rather, the neuronal activation in the trigeminal complex likely is attributable to direct depolarization of acid-sensitive trigeminal nerve fibers, for example, polymodal nociceptors, rather than through taste buds. Taken together, these findings suggest that transmission of sour taste information involves communication between Type III taste cells and 5-HT 3 -expressing afferent nerve fibers that project to a restricted portion of the nTS consistent with a crude mapping of taste quality information in the primary gustatory nucleus. © 2017 Wiley Periodicals, Inc.

  16. A Numerical Study of the Sour Gas Reforming in a Dielectric Barrier Discharge Reactor

    Directory of Open Access Journals (Sweden)

    Sajedeh Shahsavari

    2016-10-01

    Full Text Available In this paper, using a one-dimensional simulation model, the reforming process of sour gas, i.e. CH4, CO2, and H2S, to the various charged particles and syngas in a dielectric barrier discharge (DBD reactor is studied. An electric field is applied across the reactor radius, and thus a non-thermal plasma discharge is formed within the reactor. Based on the space-time coupled finite element method, the governing equations are solved, and the temporal and spatial profiles of different formed charged species from sour gas inside the plasma reactor are verified. It is observed that the electric field increases radially towards the cathode electrode. Moreover, the electron density growth rate at the radial positions closer to the cathode surface is smaller than the one in the anode electrode region. Furthermore, as time progresses, the positive ions density near the anode electrode is higher. In addition, the produced syngas density is mainly concentrated in the proximity of anode dielectric electrode.

  17. 21 CFR 131.160 - Sour cream.

    Science.gov (United States)

    2010-04-01

    ... CONSUMPTION MILK AND CREAM Requirements for Specific Standardized Milk and Cream § 131.160 Sour cream. (a... of analysis. Referenced methods in paragraph (c) (1) and (2) of this section are from “Official Methods of Analysis of the Association of Official Analytical Chemists,” 13th Ed. (1980), which is...

  18. SOUR CHERRY (Prunus cerasus L. GENETIC VARIABILITY AND PHOTOSYNTHETIC EFFICIENCY DURING DROUGHT

    Directory of Open Access Journals (Sweden)

    Marija Viljevac

    2012-12-01

    Full Text Available Sour cherry is an important fruit in Croatian orchards. Cultivar Oblačinska is predominant in existing orchards with noted intracultivar phenotypic heterogeneity. In this study, the genetic variability of 22 genotypes of cvs. Oblačinska, Maraska and Cigančica, as well as standard cvs. Kelleris 14, Kelleris 16, Kereška, Rexelle and Heimann conserved were investigated. Two types of molecular markers were used: microsatellite markers (SSR in order to identify intercultivar, and AFLP in order to identify intracultivar variabilities. A set of 12 SSR markers revealed small genetic distance between cvs. Maraska and Oblačinska while cv. Cigančica is affined to cv. Oblačinska. Furthermore, cvs. Oblačinska, Cigančica and Maraska were characterized compared to standard ones. AFLP markers didn`t confirm significant intracultivar variability of cv. Oblačinska although the variability has been approved at the morphological, chemical and pomological level. Significant corelation between SSR and AFLP markers was found. Identification of sour cherry cultivars tolerant to drought will enable the sustainability of fruit production with respect to the climate change in the future. For this purpose, the tolerance of seven sour cherry genotypes (cvs. Kelleris 16, Maraska, Cigančica and Oblačinska represented by 4 genotypes: OS, 18, D6 and BOR to drought conditions was tested in order to isolate genotypes with the desired properties. In the greenhouse experiment, cherry plants were exposed to drought stress. The leaf relative water content, OJIP test parameters which specify efficiency of the photosynthetic system based on measurements of chlorophyll a fluorescence, and concentrations of photo-synthetic pigments during the experiment were measured as markers of drought tolerance. Photosynthetic performance index (PIABS comprises three key events in the reaction centre of photosystem II affecting the photosynthetic activity: the absorption of energy

  19. Genetic and molecular characterization of three novel S-haplotypes in sour cherry (Prunus cerasus L.).

    Science.gov (United States)

    Tsukamoto, Tatsuya; Potter, Daniel; Tao, Ryutaro; Vieira, Cristina P; Vieira, Jorge; Iezzoni, Amy F

    2008-01-01

    Tetraploid sour cherry (Prunus cerasus L.) exhibits gametophytic self-incompatibility (GSI) whereby the specificity of self-pollen rejection is controlled by alleles of the stylar and pollen specificity genes, S-RNase and SFB (S haplotype-specific F-box protein gene), respectively. As sour cherry selections can be either self-compatible (SC) or self-incompatible (SI), polyploidy per se does not result in SC. Instead the genotype-dependent loss of SI in sour cherry is due to the accumulation of non-functional S-haplotypes. The presence of two or more non-functional S-haplotypes within sour cherry 2x pollen renders that pollen SC. Two new S-haplotypes from sour cherry, S(33) and S(34), that are presumed to be contributed by the P. fruticosa species parent, the complete S-RNase and SFB sequences of a third S-haplotype, S(35), plus the presence of two previously identified sweet cherry S-haplotypes, S(14) and S(16) are described here. Genetic segregation data demonstrated that the S(16)-, S(33)-, S(34)-, and S(35)-haplotypes present in sour cherry are fully functional. This result is consistent with our previous finding that 'hetero-allelic' pollen is incompatible in sour cherry. Phylogenetic analyses of the SFB and S-RNase sequences from available Prunus species reveal that the relationships among S-haplotypes show no correspondence to known organismal relationships at any taxonomic level within Prunus, indicating that polymorphisms at the S-locus have been maintained throughout the evolution of the genus. Furthermore, the phylogenetic relationships among SFB sequences are generally incongruent with those among S-RNase sequences for the same S-haplotypes. Hypotheses compatible with these results are discussed.

  20. Water-base acrylic terpolymer as a corrosion inhibitor for SAE1018 in simulated sour petroleum solution in stagnant and hydrodynamic conditions

    International Nuclear Information System (INIS)

    Vakili Azghandi, M.; Davoodi, A.; Farzi, G.A.; Kosari, A.

    2012-01-01

    Highlights: ► Corrosion inhibition of a water-base copolymer, ATP, was studied. ► Efficiency more than 90% was obtained with 0.8 mmol/L ATP in 2000 rpm. ► ATP obeys Langmuir isotherm in static and hydrodynamic conditions. ► With the presence of ATP, OM images showed a decrease in surface attack. - Abstract: The effect of static and hydrodynamic conditions (0–2000 rpm) on corrosion inhibition of a water-base acrylic terpolymer (ATP), methyl methacrylate/butyl acrylate/acrylic acid, for SAE1018 steel in simulated sour petroleum corrosive solution (NACE 1D196) were investigated by AC/DC electrochemical tests. Increase in rotation speed accelerates the corrosion rate; however the corrosion inhibitor efficiency increases. This was attributed to the enhanced mass transport of inhibitor molecules to the metal surface. OM examinations also demonstrate that in presence of ATP, a decrease in corrosion attacks is observed. Thermodynamic calculations also showed that ATP obeys Langmuir adsorption isotherm and adsorbs chemically into the surface.

  1. A large increase of sour taste receptor cells in Skn-1-deficient mice does not alter the number of their sour taste signal-transmitting gustatory neurons.

    Science.gov (United States)

    Maeda, Naohiro; Narukawa, Masataka; Ishimaru, Yoshiro; Yamamoto, Kurumi; Misaka, Takumi; Abe, Keiko

    2017-05-01

    The connections between taste receptor cells (TRCs) and innervating gustatory neurons are formed in a mutually dependent manner during development. To investigate whether a change in the ratio of cell types that compose taste buds influences the number of innervating gustatory neurons, we analyzed the proportion of gustatory neurons that transmit sour taste signals in adult Skn-1a -/- mice in which the number of sour TRCs is greatly increased. We generated polycystic kidney disease 1 like 3-wheat germ agglutinin (pkd1l3-WGA)/Skn-1a +/+ and pkd1l3-WGA/Skn-1a -/- mice by crossing Skn-1a -/- mice and pkd1l3-WGA transgenic mice, in which neural pathways of sour taste signals can be visualized. The number of WGA-positive cells in the circumvallate papillae is 3-fold higher in taste buds of pkd1l3-WGA/Skn-1a -/- mice relative to pkd1l3-WGA/Skn-1a +/+ mice. Intriguingly, the ratio of WGA-positive neurons to P2X 2 -expressing gustatory neurons in nodose/petrosal ganglia was similar between pkd1l3-WGA/Skn-1a +/+ and pkd1l3-WGA/Skn-1a -/- mice. In conclusion, an alteration in the ratio of cell types that compose taste buds does not influence the number of gustatory neurons that transmit sour taste signals. Copyright © 2017. Published by Elsevier B.V.

  2. Sweet and sour taste preferences of children

    NARCIS (Netherlands)

    Liem, D.G.

    2004-01-01

    In the industrialized countries children have many foods to choose from, both healthy and unhealthy products, these choices mainly depend on children's taste preferences. The present thesis focused on preferences for sweet and sour taste of young children (4- to 12-years of age) living in the US and

  3. Bioactivity of sour cherry cultivars grown in Denmark

    DEFF Research Database (Denmark)

    Khoo, Gaik Ming; Clausen, Morten Rahr; Pedersen, Bjarne Hjelmsted

    2012-01-01

    Thirty four varieties of sour cherries (Prunus cerasus) were investigated for their total antioxidant activity, Caco-2 cancer cell proliferation inhibitory activity and effect on prostaglandin E2 (PGE2) production. Total phenolic content, oxygen radical absorbance capacity (ORAC) and cancer cell ...

  4. Polyphenols and Volatiles in Fruits of Two Sour Cherry Cultivars, Some Berry Fruits and Their Jams

    Directory of Open Access Journals (Sweden)

    Branka Levaj

    2010-01-01

    Full Text Available This paper reports about the content of polyphenols and volatiles in fresh fruits of two sour cherry cultivars (Marasca and Oblačinska, some berry fruits (strawberry Maya, raspberry Willamette and wild blueberry and the corresponding low sugar jams. Phenolic compounds (hydroxybenzoic and hydroxycinnamic acids, flavan 3-ols and flavonols were determined by high-performance liquid chromatography (HPLC. Those found in the fruits were also found in the jams. Jams contained lower amounts of polyphenols than fresh fuits, but their overall retention in jams was relatively high. Among fruits, sour cherry Marasca had the highest level of polyphenols, while sour cherry Marasca jam and raspberry Willamette jam had the highest level of polyphenols among jams. The major flavonoid in all investigated fruits, except in sour cherry Oblačinska, was (–-epicatechin. Sour cherry Marasca had the highest level of (–-epicatechin (95.75 mg/kg, and it also contained very high amounts of flavonols, derivatives of quercetin and kaempferol. Hydroxybenzoic acids (HBAs were not found in sour cherries Marasca and Oblačinska, but were found in berry fruits and jams. Phenolic compound (+-gallocatechin was found only in Marasca fruit and jam. Ellagic acid was found in the highest concentration in raspberry Willamette fruit and jam. Hydroxycinnamic acids (HCAs were found in all the investigated fruits, with the exception of a derivative of ferulic acid, which was not found in strawberry. Derivatives of caffeic, p-coumaric and chlorogenic acids were found in all the investigated fruits, with chlorogenic acid being the most abundant, especially in sour cherry Marasca. Volatiles were determined by gas chromatography (GC and expressed as the peak area of the identified compounds. All investigated volatiles of fresh fruit were also determined in the related jams with relatively high retention. Sour cherries Marasca and Oblačinska contained the same volatile compounds, but

  5. Sour pressure swing adsorption process

    Science.gov (United States)

    Bhadra, Shubhra Jyoti; Wright, Andrew David; Hufton, Jeffrey Raymond; Kloosterman, Jeffrey William; Amy, Fabrice; Weist, Jr., Edward Landis

    2017-11-07

    Methods and apparatuses for separating CO.sub.2 and sulfur-containing compounds from a synthesis gas obtained from gasification of a carbonaceous feedstock. The primary separating steps are performed using a sour pressure swing adsorption (SPSA) system, followed by an acid gas enrichment system and a sulfur removal unit. The SPSA system includes multiple pressure equalization steps and a rinse step using a rinse gas that is supplied from a source other than directly from one of the adsorber beds of the SPSA system.

  6. Effect of different levels of sugar on qualitative characteristics of lassi prepared from sour dahi

    Directory of Open Access Journals (Sweden)

    Muhammad Shah Moazzem

    2018-08-01

    Full Text Available An investigation was carried out to develop lassi from sour dahi using different levels of sugar (10, 15, 20 and 25% and 15% water. Lassi quality was assayed through the study of physical, chemical and microbiological parameters. Results revealed that significant difference existed in overall physical score of lassi samples and the highest score was found in 15% sugar lassi whereas, the lowest score was found in 25% sugar lassi. Total solids, carbohydrate, fat, protein and ash contents differed significantly among various levels of sugar added lassi. From chemical test, it appears that, 15% sugar added lassi possess the highest fat and protein values whereas, the highest total solids and carbohydrate values posses in 25% sugar added lassi. No significant difference (p>0.05 revealed in terms of pH value and acidity percentage among lassi types. Lassi made from 10% sugar was most inferior than other levels of sugar added lassi in respect of microbiological quality- total viable count (×104 cfu/mL content was 95.67±2.08 and coliform (×10 cfu/mL content was 1.00±0.00. Considering above mentioned quality aspects, it might be resolved that lassi could be prepared successfully from sour dahi with 15% sugar keeping water level constant at 15%. [Fundam Appl Agric 2018; 3(2.000: 434-439

  7. Antimicrobial effect of sour pomegranate sauce on Escherichia coli O157:H7 and Staphylococcus aureus.

    Science.gov (United States)

    Kışla, Duygu; Karabıyıklı, Şeniz

    2013-05-01

    Pomegranate sauce is one of the most popular pomegranate products produced in Turkey. This study was conducted to determine the minimum inhibitory concentrations (MICs) of both traditional and commercial sour pomegranate sauce samples on Staphylococcus aureus (ATCC 25923) and Escherichia coli O157:H7 (ATCC 43895). The initial microflora of the pomegranate sauce samples was determined by performing the enumerations of total aerobic mesophilic bacteria, yeast and mold, S. aureus, E. coli, and the determination of Salmonella spp. MIC tests were applied to the neutralized and the original (unneutralized) sour pomegranate sauce samples in order to put forth the inhibition effect depending on low pH value. It was found that inhibitory effect of the traditional and the commercial samples, except one sample, on pathogens was not only due to the acidity of the products. The results of MIC tests indicated that although both traditional and commercial samples showed a considerable inhibitory effect on test microorganisms, the traditional pomegranate sauce samples were more effective than the commercial ones. © 2013 Institute of Food Technologists®

  8. Characterization of Sugar and Polyphenolic Diversity in Floral Nectar of Different 'Oblačinska' Sour Cherry Clones.

    Science.gov (United States)

    Guffa, Basem; Nedić, Nebojša M; Dabić Zagorac, Dragana Č; Tosti, Tomislav B; Gašić, Uroš M; Natić, Maja M; Fotirić Akšić, Milica M

    2017-09-01

    'Oblačinska' sour cherry, an autochthonous cultivar, is the most planted cultivar in Serbian orchards. Since fruit trees in temperate zone reward insects by producing nectar which 'quality' affects the efficiency of insect pollination, the aim of this study was analyzing of sugars and polyphenolics in floral nectar of 16 'Oblačinska' sour cherry clones with different yielding potential. The contents of sugars and sugar alcohols were analyzed by ion chromatography, while polyphenolic profile was established using liquid chromatography/mass spectrometry technique. Fourteen sugars and six sugar alcohols were detected in nectar samples and the most abundant were fructose, glucose, and sucrose. Eleven polyphenols were quantified using available standards, while another 17 were identified according to their exact masses and characteristic fragmentations. Among quantified polyphenols, rutin, naringenin, and chrysin were the most abundant in nectar. Principal component analysis showed that some polyphenol components (naringin, naringenin, and rutin) together with sugars had high impact of spatial distribution of nectar samples on score plot. © 2017 Wiley-VHCA AG, Zurich, Switzerland.

  9. Mulher, cura e pajelança em Soure (Ilha do Marajó-PA).

    OpenAIRE

    Mayra Cristina Silva Faro; UEPA

    2012-01-01

    Neste trabalho pretendo apresentar alguns resultados de uma pesquisa que vem sendo realizada desde 2009 sobre a pajelança cabocla e as mulheres pajés na cidade de Soure, Ilha do Marajó/PA. Este estudo tem como objetivos analisar práticas e saberes de cura em Soure, e observar o papel da mulher no contexto religioso e simbólico da pajelança. Compreende-se pajelança cabocla como um conjunto de crenças e práticas de cura bastante difundida na Amazônia, em que encontram-se mesclados em graus vari...

  10. Produced water - composition and analysis

    International Nuclear Information System (INIS)

    Kvernheim, Arne Lund

    1998-01-01

    Produced water can be defined as ''High volume waste-water separated from oil and gas that is produced from subsurface formations''. The water contains aliphatic and aromatic hydrocarbons, particulate matter and soluble salts as well as elements originating from formations and from sea water injections. Residues of chemicals may also be present. The accepted North Sea discharge limit is 40 ppm. In this presentation the focus will be on the chemical composition of produced water and on the challenges involved in developing and implementing analytical methods. The focus will also be on the development of a new oil-in-water analytical method as a replacement for the Freon method. 7 refs., 1 tab

  11. Quality of sour cherry juice of different clones and cultivars (Prunus cerasus L.) determined by a combined sensory and NMR spectroscopic approach

    DEFF Research Database (Denmark)

    Clausen, Morten Rahr; Pedersen, Bjarne Hjelmsted; Bertram, Hanne Christine S.

    2011-01-01

    Juice was manufactured from seven different sour cherry clones/cultivars and evaluated by quantitative descriptive sensory analysis and 1H NMR spectroscopy. The sensory evaluation showed a large variation in several sensory attributes between the sour cherry clones/cultivars, which could be divided...... into two groups on the basis of both the sensory data and the NMR spectroscopic data. These groups were closely related to the genetic background of the clones. Kelleris clones were distinctly different from Stevnsberry and Fanal clones. Hence, 1H NMR spectroscopic data seem to correlate with sensory...... quality of different sour cherry clones. In addition, malic acid was the most important metabolite for modeling the two highly correlated sensory attributes sweetness and sourness, whereas the glucose content had a slight effect and the fructose content had no impact on sweetness/sourness. Other...

  12. Produced Water Management and Beneficial Use

    International Nuclear Information System (INIS)

    Brown, Terry; Frost, Carol; Hayes, Thomas; Heath, Leo; Johnson, Drew; Lopez, David; Saffer, Demian; Urynowicz, Michael; Wheaton, John; Zoback, Mark

    2007-01-01

    Large quantities of water are associated with the production of coalbed methane (CBM) in the Powder River Basin (PRB) of Wyoming. The chemistry of co-produced water often makes it unsuitable for subsequent uses such as irrigated agriculture. However, co-produced waters have substantial potential for a variety of beneficial uses. Achieving this potential requires the development of appropriate water management strategies. There are several unique characteristics of co-produced water that make development of such management strategies a challenge. The production of CBM water follows an inverse pattern compared to traditional wells. CBM wells need to maintain low reservoir pressures to promote gas production. This need renders the reinjection of co-produced waters counterproductive. The unique water chemistry of co-produced water can reduce soil permeability, making surface disposal difficult. Unlike traditional petroleum operations where co-produced water is an undesirable by-product, co-produced water in the PRB often is potable, making it a highly valued resource in arid western states. This research project developed and evaluated a number of water management options potentially available to CBM operators. These options, which focus on cost-effective and environmentally-sound practices, fall into five topic areas: Minimization of Produced Water, Surface Disposal, Beneficial Use, Disposal by Injection and Water Treatment. The research project was managed by the Colorado Energy Research Institute (CERI) at the Colorado School of Mines (CSM) and involved personnel located at CERI, CSM, Stanford University, Pennsylvania State University, the University of Wyoming, the Argonne National Laboratory, the Gas Technology Institute, the Montana Bureau of Mining and Geology and PVES Inc., a private firm

  13. Produced Water Management and Beneficial Use

    Energy Technology Data Exchange (ETDEWEB)

    Terry Brown; Carol Frost; Thomas Hayes; Leo Heath; Drew Johnson; David Lopez; Demian Saffer; Michael Urynowicz; John Wheaton; Mark Zoback

    2007-10-31

    Large quantities of water are associated with the production of coalbed methane (CBM) in the Powder River Basin (PRB) of Wyoming. The chemistry of co-produced water often makes it unsuitable for subsequent uses such as irrigated agriculture. However, co-produced waters have substantial potential for a variety of beneficial uses. Achieving this potential requires the development of appropriate water management strategies. There are several unique characteristics of co-produced water that make development of such management strategies a challenge. The production of CBM water follows an inverse pattern compared to traditional wells. CBM wells need to maintain low reservoir pressures to promote gas production. This need renders the reinjection of co-produced waters counterproductive. The unique water chemistry of co-produced water can reduce soil permeability, making surface disposal difficult. Unlike traditional petroleum operations where co-produced water is an undesirable by-product, co-produced water in the PRB often is potable, making it a highly valued resource in arid western states. This research project developed and evaluated a number of water management options potentially available to CBM operators. These options, which focus on cost-effective and environmentally-sound practices, fall into five topic areas: Minimization of Produced Water, Surface Disposal, Beneficial Use, Disposal by Injection and Water Treatment. The research project was managed by the Colorado Energy Research Institute (CERI) at the Colorado School of Mines (CSM) and involved personnel located at CERI, CSM, Stanford University, Pennsylvania State University, the University of Wyoming, the Argonne National Laboratory, the Gas Technology Institute, the Montana Bureau of Mining and Geology and PVES Inc., a private firm.

  14. Formation and Control of Sulfur Oxides in Sour Gas Oxy-Combustion: Prediction Using a Reactor Network Model

    KAUST Repository

    Bongartz, Dominik

    2015-11-19

    © 2015 American Chemical Society. Sour natural gas currently requires expensive gas cleanup before it can be used in power generation because it contains large amounts of hydrogen sulfide (H2S) and carbon dioxide (CO2) that entail a low heating value and highly corrosive combustion products. A potential alternative is to use the gas directly in a gas turbine process employing oxy-fuel combustion, which could eliminate the need for gas cleanup while also enabling the application of carbon capture and sequestration, possibly combined with enhanced oil recovery (EOR). However, the exact influence of an oxy-fuel environment on the combustion products of sour gas has not been quantified yet. In this work, we used a reactor network model for the combustor and the gas turbine together with our recently assembled and validated detailed chemical reaction mechanism for sour gas combustion to investigate the influence of some basic design parameters on the combustion products of natural gas and sour gas in CO2 or H2O diluted oxy-fuel combustion as well as in conventional air combustion. Our calculations show that oxy-fuel combustion produces up to 2 orders of magnitude less of the highly corrosive product sulfur trioxide (SO3) than air combustion, which clearly demonstrates its potential in handling sulfur containing fuels. Unlike in air combustion, in oxy-fuel combustion, SO3 is mainly formed in the flame zone of the combustor and is then consumed as the combustion products are cooled in the dilution zone of the combustor and the turbine. In oxy-fuel combustion, H2O dilution leads to a higher combustion efficiency than CO2 dilution. However, if the process is to be combined with EOR, CO2 dilution makes it easier to comply with the very low levels of oxygen (O2) required in the EOR stream. Our calculations also show that it might even be beneficial to operate slightly fuel-rich because this simultaneously decreases the O2 and SO3 concentration further. The flame zone

  15. Ghrelin is produced in taste cells and ghrelin receptor null mice show reduced taste responsivity to salty (NaCl and sour (citric acid tastants.

    Directory of Open Access Journals (Sweden)

    Yu-Kyong Shin

    2010-09-01

    Full Text Available The gustatory system plays a critical role in determining food preferences, food intake and energy balance. The exact mechanisms that fine tune taste sensitivity are currently poorly defined, but it is clear that numerous factors such as efferent input and specific signal transduction cascades are involved.Using immunohistochemical analyses, we show that ghrelin, a hormone classically considered to be an appetite-regulating hormone, is present within the taste buds of the tongue. Prepro-ghrelin, prohormone convertase 1/3 (PC 1/3, ghrelin, its cognate receptor (GHSR, and ghrelin-O-acyltransferase (GOAT , the enzyme that activates ghrelin are expressed in Type I, II, III and IV taste cells of mouse taste buds. In addition, ghrelin and GHSR co-localize in the same taste cells, suggesting that ghrelin works in an autocrine manner in taste cells. To determine a role for ghrelin in modifying taste perception, we performed taste behavioral tests using GHSR null mice. GHSR null mice exhibited significantly reduced taste responsivity to sour (citric acid and salty (sodium chloride tastants.These findings suggest that ghrelin plays a local modulatory role in determining taste bud signaling and function and could be a novel mechanism for the modulation of salty and sour taste responsivity.

  16. Dense film polyimide membranes for aggressive sour gas feed separations

    KAUST Repository

    Kraftschik, Brian; Koros, William J.; Johnson, J.R.; Karvan, Oguz

    2013-01-01

    Dense film membranes of the copolyimide 6FDA-DAM:DABA (3:2) are studied for simultaneous removal of CO2 and H2S from sour natural gas streams. Pure and mixed gas permeation as well as pure gas sorption data are reported at 35°C and pressures up to 62bar. The H2S partial pressures used are representative of highly aggressive field operations. Penetrant-induced plasticization effects are evident at feed pressures below 1bar in pure H2S feeds; sub-Tg thermal annealing is used to effectively mitigate this effect, and these annealed films are used throughout the study. Surprisingly, H2S/CH4 selectivity nearly doubles for mixed gas testing in comparison to the pure component ideal selectivity values and approaches the level of a state-of-the-art glassy polymer, cellulose acetate (CA), at H2S partial pressures above 2bar. Furthermore, permeation experiments using a 9.95% H2S, 19.9% CO2, 70.15% CH4 mixture at low feed pressures give CO2/CH4 selectivity of up to 49-over 30% greater than the pure component selectivity for 6FDA-DAM:DABA (3:2). The overall sour gas separation performance of this polyimide is comparable to high-performance rubbery polymer membranes, which have been reported for only moderate H2S partial pressure feeds, and is superior to that for CA based on a practical combined acid gas separation efficiency metric that we introduce. Finally, methods for continued development of the current polyimide membrane material for aggressive sour gas separations are presented. © 2012 Elsevier B.V.

  17. Dense film polyimide membranes for aggressive sour gas feed separations

    KAUST Repository

    Kraftschik, Brian

    2013-02-01

    Dense film membranes of the copolyimide 6FDA-DAM:DABA (3:2) are studied for simultaneous removal of CO2 and H2S from sour natural gas streams. Pure and mixed gas permeation as well as pure gas sorption data are reported at 35°C and pressures up to 62bar. The H2S partial pressures used are representative of highly aggressive field operations. Penetrant-induced plasticization effects are evident at feed pressures below 1bar in pure H2S feeds; sub-Tg thermal annealing is used to effectively mitigate this effect, and these annealed films are used throughout the study. Surprisingly, H2S/CH4 selectivity nearly doubles for mixed gas testing in comparison to the pure component ideal selectivity values and approaches the level of a state-of-the-art glassy polymer, cellulose acetate (CA), at H2S partial pressures above 2bar. Furthermore, permeation experiments using a 9.95% H2S, 19.9% CO2, 70.15% CH4 mixture at low feed pressures give CO2/CH4 selectivity of up to 49-over 30% greater than the pure component selectivity for 6FDA-DAM:DABA (3:2). The overall sour gas separation performance of this polyimide is comparable to high-performance rubbery polymer membranes, which have been reported for only moderate H2S partial pressure feeds, and is superior to that for CA based on a practical combined acid gas separation efficiency metric that we introduce. Finally, methods for continued development of the current polyimide membrane material for aggressive sour gas separations are presented. © 2012 Elsevier B.V.

  18. Source-Sink Relations in Fruits VII. Effects of Pruning in Sour Cherry and Plum

    DEFF Research Database (Denmark)

    Toldam-Andersen, Torben Bo; Hansen, P.

    1993-01-01

    Sour cherries cv. 'Stevnsbær' and plums cv. 'Victoria' were heavily pruned in 1987. Fruit samples were collected during the growing season and concentrations of different quality components were determined. Pruning resulted in a small increase in fruit size, the effect being greater on the older...... trees (sour cherries) or at the lower crop load (plum). Additionally, pruning decreased the con­centrations of total and soluble dry matter and of anthocya­nins ('Stevnsbær'), while titratable acids showed an increas­ing tendency. The effects of pruning are discussed based on influences on root...

  19. Direct photothermal techniques for quantification of anthocyanins in sour cherry cultivars

    NARCIS (Netherlands)

    Doka, O.; Ficzek, G.; Bicanic, D.D.; Spruijt, R.B.; Luterotti, S.; Toth, M.; Buijnsters, J.G.; György Végvári, G.

    2011-01-01

    The analytical performance of the newly proposed laser-based photoacoustic spectroscopy (PAS) and of optothermal window (OW) method for quantification of total anthocyanin concentration (TAC) in five sour cherry varieties is compared to that of the spectrophotometry (SP). High performance liquid

  20. Evaluation of the glycoside hydrolase activity of a Brettanomyces strain on glycosides from sour cherry (Prunus cerasus L.) used in the production of special fruit beers.

    Science.gov (United States)

    Daenen, Luk; Sterckx, Femke; Delvaux, Freddy R; Verachtert, Hubert; Derdelinckx, Guy

    2008-11-01

    The glycoside hydrolase activity of Saccharomyces cerevisiae and Brettanomyces custersii was examined on sour cherry (Prunus cerasus L.) glycosides with bound volatile compounds. Refermentations by the beta-glucosidase-negative S. cerevisiae strains LD25 and LD40 of sour cherry juice-supplemented beer demonstrated only a moderate increase of volatiles. In contrast, the beta-glucosidase-positive B. custersii strain LD72 showed a more pronounced activity towards glycosides with aliphatic alcohols, aromatic compounds and terpenoid alcohols. Important contributors to sour cherry aroma such as benzaldehyde, linalool and eugenol were released during refermentation as shown by analytical tools. A gradually increasing release was observed during refermentations by B. custersii when whole sour cherries, sour cherry pulp or juice were supplemented in the beer. Refermentations with whole sour cherries and with sour cherry stones demonstrated an increased formation of benzyl compounds. Thus, amygdalin was partially hydrolysed, and a large part of the benzaldehyde formed was mainly reduced to benzyl alcohol and some further esterified to benzyl acetate. These findings demonstrate the importance and interesting role of certain Brettanomyces species in the production of fruit lambic beers such as 'Kriek'.

  1. Sulphur recovery and sulphur emissions at Alberta sour gas plants : annual report for 2005

    International Nuclear Information System (INIS)

    2005-01-01

    The sulphur recovery of Alberta's grandfathered sour gas plants is monitored by the Alberta Energy and Utilities Board. This report provides an annual summary of industry performance for sulphur recovery at large acid gas flaring sour gas plants, and sulphur recovery at all acid gas injection sour gas plants. It follows Interim Directive (ID) 2001-3 which stipulates guidelines for sulphur recovery for the province of Alberta. It includes a list of grandfathered and non grandfathered plants in Alberta. Grandfathered sulphur recovery plants that exceed expectations have the option to file a sulphur emission performance credit report and can use the credits to meet some of their sulphur requirement in the future. Acid gas flaring plants face more stringent requirements and cannot earn credits. Several plants have degrandfathered in the past 5 years. Eleven have made upgrades, 4 have been relicensed to meet the requirements for new plants, and 4 have shut down. Forty-one grandfathered plants remain. Sulphur emissions have decreased 39 per cent for grandfathered acid gas flaring plants, and 28 per cent for grandfathered sulphur recovery plants. 10 tabs., 3 figs

  2. Wintertime Emissions from Produced Water Ponds

    Science.gov (United States)

    Evans, J.; Lyman, S.; Mansfield, M. L.

    2013-12-01

    Every year oil and gas drilling in the U.S. generates billions of barrels of produced water (water brought to the surface during oil or gas production). Efficiently disposing of produced water presents a constant financial challenge for producers. The most noticeable disposal method in eastern Utah's Uintah Basin is the use of evaporation ponds. There are 427 acres of produced water ponds in the Uintah Basin, and these were used to evaporate more than 5 million barrels of produced water in 2012, 6% of all produced water in the Basin. Ozone concentrations exceeding EPA standards have been observed in the Uintah Basin during winter inversion conditions, with daily maximum 8 hour average concentrations at some research sites exceeding 150 parts per billion. Produced water contains ozone-forming volatile organic compounds (VOC) which escape into the atmosphere as the water is evaporated, potentially contributing to air quality problems. No peer-reviewed study of VOC emissions from produced water ponds has been reported, and filling this gap is essential for the development of accurate emissions inventories for the Uintah Basin and other air sheds with oil and gas production. Methane, carbon dioxide, and VOC emissions were measured at three separate pond facilities in the Uintah Basin in February and March of 2013 using a dynamic flux chamber. Pond emissions vary with meteorological conditions, so measurements of VOC emissions were collected during winter to obtain data relevant to periods of high ozone production. Much of the pond area at evaporation facilities was frozen during the study period, but areas that actively received water from trucks remained unfrozen. These areas accounted for 99.2% of total emissions but only 9.5% of the total pond area on average. Ice and snow on frozen ponds served as a cap, prohibiting VOC from being emitted into the atmosphere. Emissions of benzene, toluene, and other aromatic VOCs averaged over 150 mg m-2 h-1 from unfrozen pond

  3. Effective pollination period in "Oblačinska" sour cherry clones

    Directory of Open Access Journals (Sweden)

    Fotirić-Akšić Milica

    2014-01-01

    Full Text Available To obtain high yields there should be high flower density and fruit set in sour cherry (Prunus cerasus L. production. Furthermore, in order to ensure successful fertilization, there should be satisfactory stigma receptivity, rapid pollen tube growth along the style, as well as adequate ovule longevity. This manuscript presents the study of the effective pollination period (EPP of four ‘Oblačinska’ sour cherry clones (II/2, III/9, XI/3 and XIII/1 that differs in pollen germination, fruit set and yields. In order to estimate EPP, pollination was conducted in six different stages of flower development: balloon stage, 2 d before anthesis (-2, at anthesis (0, and 2, 4, 6 and 8 d after anthеsis (DAA. The initial (IFS and final fruit set (FFS were recorded under the field conditions. Alongside with this, the rate of pollen tubes growth in the style was observed with fluorescent microscopy. The experimental design was completely randomized, a two-factorial analysis of variance was carried out and individual testing was performed using LSD test (p ≤ 0.05; p ≤ 0.01. The experiment was set in triplicates. Regarding FFS, clones II/2 and III/9 showed the best results (p ≤ 0.01 in 4 and 6 DAA. The number of pollen tubes in the style of the pistil decreased with subsequent terms of pollination, while its number in the ovule increased up to sixth day after pollination, followed by a decline. Clones II/2 and III/9 showed EPP which lasted from 6 to 8 d, while EPP found in clone XI/3, lasted only 2 d. It is concluded that only clone having long EPP should be used as parents for creating new sour cherry cultivars. [Projekat Ministarstva nauke Republike Srbije, br. TR 31063 and FP7 Project AREA 316004

  4. Investigating animal health effects of sour gas acid forming emissions

    International Nuclear Information System (INIS)

    Edwards, W.C.

    1992-01-01

    The effects of sour gas well blowout emissions on livestock are reviewed. Guidelines for safe drilling operations in hydrogen sulfide environments, general hazards and characteristics of hydrogen sulfide, and guidelines for field investigation into the effects of sour gas and acid emissions on livestock are discussed. A case history involving the Ross No. 2 gas well blowout of July 1985 in Rankin County, Mississippi is presented. The blowout lasted for 72 days, and at peak discharge the 500 ppM radius was ca 3.5 miles. A cattle embryo transplant operation located one half mile from the well was affected by the blowout. Examination by a local veterinarian of the cattle demonstrated eye irritation, epiphora, nasal discharge and coughing. After one and a half months of exposure, most animals showed clinical signs of a severe dry hacking cough, epiphora, dry rales over the thoracic inlet, and a bronchial popping sound over the lateral thorax. All animals had eye irritation. Of 55 animals showing signs of respiratory distress and eye irritations, 15 were still clinically ill in May of 1986. 7 refs., 1 tab

  5. Problems Caused by Microbes and Treatment Strategies Monitoring and Preventing Reservoir Souring Using Molecular Microbiological Methods (MMM)

    Science.gov (United States)

    Gittel, Antje

    The injection of seawater during the process of secondary oil recovery in offshore oilfields supplies huge amounts of sulphate to the prokaryotic reservoir communities. Together with the presence of oil organics and their degradation products as electron donors, this facilitates the enrichment and growth of sulphate-reducing prokaryotes (SRP) in the reservoir, as well as in pipings and top-side installations (Sunde and Torsvik, 2005; Vance and Thrasher, 2005). The activity of SRP causes severe economic problems due to the reactivity and toxicity of the produced hydrogen sulphide (H2S), one of the major problems being reservoir souring. Besides the use of broad-spectrum biocides or inhibitors for sulphate reduction, the addition of nitrate effectively decreased the net production of H2S in model column studies (Myhr et al., 2002; Hubert et al., 2005; Dunsmore et al., 2006) and field trials (Telang et al., 1997; Bødtker et al., 2008). The mechanisms by which nitrate addition might affect souring control are (i) the stimulation of heterotrophic nitrate-reducing bacteria (hNRB) that outcompete SRP for electron donors, (ii) the activity of nitrate-reducing, sulphide-oxidising bacteria (NR-SOB), and (iii) the inhibition of SRP by the production of nitrite and nitrous oxides (Sunde and Torsvik, 2005; Hubert and Voordouw, 2007).

  6. Supply, storage and handling of elemental sulfur derived from sour gas

    International Nuclear Information System (INIS)

    Clark, P.D.; Davis, P.M.; Dowling, N.I.; Calgary Univ., AB

    2003-01-01

    This presentation reviews the supply picture for solid elemental sulfur. It also assesses methods for its storage as well as the disposal of the precursor hydrogen sulfide (H 2 S) by acid gas injection. Both above and below ground block storage is considered environmentally acceptable for sulfur storage as long as measures are taken to minimize the physical and biological breakdown of the sulfur. The preferred option is to store solid elemental sulfur underground, particularly if it is to remain in storage for a prolonged period. Future changes in supply of sulfur will likely be controlled by incremental production of sour gas and utilization of oil sands bitumen. It is expected that future sulfur production from conventional crude oil will remain static or will slowly decrease. The degree to which acid gas injection is applied to large sour gas developments in the Middle East and the Caspian regions will have a significant impact on world sulfur supply. 9 refs., 1 tab., 5 figs

  7. Effect of the improved fermentation on physicochemical properties and sensorial acceptability of sour cassava starch

    Directory of Open Access Journals (Sweden)

    Maria Janete Angeloni Marcon

    2007-11-01

    Full Text Available The aim of this work was to study the effect of improved fermentation on sour cassava starch, aiming to reduce its fermentation time and to enhance its expansion capacity as well as its viscoamylographic properties and its sensorial acceptability. Results showed that the improved process of cassava starch production did not harm starch expansion, physicochemical properties or sensorial acceptability; it also produced starches with different viscoamylographic properties, which compared favourably to those of the sour cassava starch produced through current industrial methods.O Polvilho azedo é caracterizado pelas suas propriedades físicas, químicas e reológicas, as quais são diferentes do amido nativo do qual se originou. A propriedade de expansão é uma das mais importantes características do produto, sendo um parâmetro fundamental de avaliação do polvilho azedo. O resultado do perfil viscoamilográfico também é uma importante maneira de avaliação uma vez que cada amido tem um padrão viscoamilográfico definido de acordo com sua organização granular. Este trabalho determinou o efeito da fermentação melhorada pela adição de glicose, sobre o polvilho azedo, apontando para uma redução no tempo de fermentação e avaliando sua capacidade de expansão, suas propriedades viscoamilográficas e aceitabilidade sensorial. O processo de produção de polvilho azedo melhorado não prejudicou a expansão do amido, suas propriedades físico-químicas e sensoriais, mas sim resultou em amidos com diferentes propriedades viscoamilográficas melhores comparativamente ao polvilho azedo produzido pelo processo industrial atual.

  8. Producing deep-water hydrocarbons

    International Nuclear Information System (INIS)

    Pilenko, Thierry

    2011-01-01

    Several studies relate the history and progress made in offshore production from oil and gas fields in relation to reserves and the techniques for producing oil offshore. The intention herein is not to review these studies but rather to argue that the activities of prospecting and producing deep-water oil and gas call for a combination of technology and project management and, above all, of devotion and innovation. Without this sense of commitment motivating men and women in this industry, the human adventure of deep-water production would never have taken place

  9. A comparative study of the effect of green tea and sour tea on blood pressure and lipid profile in healthy adult men

    Directory of Open Access Journals (Sweden)

    Marzieh Kafeshani

    2017-06-01

    Full Text Available BACKGROUND: Cardiovascular diseases (CVD are a set of metabolic disorders affecting heart and blood vessels. Green tea and sour tea (Hibiscus sabdariffa L. have attracted significant attention recently due to their high popularity, nutrient profile and therapeutic effects. The aim of the present study was to compare the effects of green tea and sour tea supplementation on blood pressure and lipid profile in healthy adult men. METHODS: This randomized, double-blind, placebo-controlled trial included 54 healthy adult men. The participants were randomly assigned to two intervention groups receiving 450 mg green tea or sour tea and one placebo group which consumed 450 mg placebo (maltodextrin for 6 weeks. Blood pressure, lipid profile, dietary intake and physical activity were measured pre- and post-intervention and compared. RESULTS: After 6 weeks of intervention, sour tea supplementation led to a significant decrease in systolic blood pressure (SBP compared with the placebo group. However, we faild to find any significant difference in SBP between green tea and control groups. Also, no significant changes were observed in diastolic blood pressure (DBP and lipid profile between the three groups. In comparison with baseline, there was a significant increase in the mean level of serum high-density lipoprotein cholesterol (HDL-C in green tea and sour tea groups. Also, the interventions resulted in significant decrease in the mean levels of serum total cholesterol (TC and low-density lipoprotein cholesterol (LDL-C and DBP in the sour tea group compared with the pre-intervention value. CONCLUSION: On the basis of our findings, sour tea supplementation led to decreased SBP in healthy men compared with the placebo, but there was no significant difference between their effects on DBP and lipid profile. 

  10. Degradation of Anthocyanin Content in Sour Cherry Juice During Heat Treatment

    Directory of Open Access Journals (Sweden)

    Lilla Szalóki-Dorkó

    2015-01-01

    Full Text Available Sour cherry juices made from two sour cherry cultivars (Érdi bőtermő and Kántorjánosi 3, were investigated to determine their total anthocyanin content and half-life of anthocyanins during heat treatment at different temperatures (70, 80 and 90 °C for 4 h. Before the heat treatment, Érdi bőtermő juice had higher anthocyanin concentration (812 mg/L than Kántorjánosi 3 juice (513 mg/L. The greatest heat sensitivity of anthocyanins was measured at 90 °C, while the treatments at 80 and 70 °C caused lower thermal degradation. The loss of anthocyanins in Érdi bőtermő juice after treatment was 38, 29 and 18 %, respectively, while in Kántorjánosi 3 juice losses of 46, 29 and 19 % were observed, respectively. At 90 °C sour cherry Érdi bőtermő juice had higher half-life (t1/2 of anthocyanins, while the Kántorjánosi 3 juice had higher t1/2 values at 70 °C. Cyanidin-3-glucosyl-rutinoside was present in higher concentrations in both cultivars (Érdi bőtermő: 348 and Kántorjánosi 3: 200 mg/L than cyanidin-3-rutinoside (177 and 121 mg/L before treatment. However, during the experiment, cyanidin-3-rutinoside was proved to be more resistant to heat. Comparing the two varieties, both investigated pigment compounds were more stable in Kántorjánosi 3 than in Érdi bőtermő. Degradation rate of anthocyanins was cultivar-dependent characteristic, which should be taken into account in the food production.

  11. ANAEROBIC BIOLOGICAL TREATMENT OF PRODUCED WATER

    Energy Technology Data Exchange (ETDEWEB)

    John R. Gallagher

    2001-07-31

    During the production of oil and gas, large amounts of water are brought to the surface and must be disposed of in an environmentally sensitive manner. This is an especially difficult problem in offshore production facilities where space is a major constraint. The chief regulatory criterion for produced water is oil and grease. Most facilities have little trouble meeting this criterion using conventional oil-water separation technologies. However, some operations have significant amounts of naphthenic acids in the water that behave as oil and grease but are not well removed by conventional technologies. Aerobic biological treatment of naphthenic acids in simulated-produced water has been demonstrated by others; however, the system was easily overloaded by the large amounts of low-molecular-weight organic acids often found in produced waters. The objective of this research was to determine the ability of an anaerobic biological system to treat these organic acids in a simulated produced water and to examine the potential for biodegradation of the naphthenic acids in the anaerobic environment. A small fixed-film anaerobic biological reactor was constructed and adapted to treat a simulated produced water. The bioreactor was tubular, with a low-density porous glass packing material. The inocula to the reactor was sediment from a produced-water holding pond from a municipal anaerobic digester and two salt-loving methanogenic bacteria. During start-up, the feed to the reactor contained glucose as well as typical produced-water components. When glucose was used, rapid gas production was observed. However, when glucose was eliminated and the major organic component was acetate, little gas was generated. Methane production from acetate may have been inhibited by the high salt concentrations, by sulfide, or because of the lack, despite seeding, of microbes capable of converting acetate to methane. Toluene, a minor component of the produced water (0.1 g/L) was removed in the

  12. Optimization of Sour Cherry Juice Spray Drying as
Affected by Carrier Material and Temperature

    Science.gov (United States)

    Zorić, Zoran; Pedisić, Sandra; Dragović-Uzelac, Verica

    2016-01-01

    Summary Response surface methodology was applied for optimization of the sour cherry Marasca juice spray drying process with 20, 30 and 40% of carriers maltodextrin with dextrose equivalent (DE) value of 4–7 and 13–17 and gum arabic, at three drying temperatures: 150, 175 and 200 °C. Increase in carrier mass per volume ratio resulted in lower moisture content and powder hygroscopicity, higher bulk density, solubility and product yield. Higher temperatures decreased the moisture content and bulk density of powders. Temperature of 200 °C and 27% of maltodextrin with 4–7 DE were found to be the most suitable for production of sour cherry Marasca powder. PMID:28115901

  13. Changes in taste sensation of sour, salty, sweet, bitter, umami, and spicy, as well as levels of malondialdehyde serum in radiographers

    Directory of Open Access Journals (Sweden)

    Agniz Nur Aulia

    2016-06-01

    on the effects of radiation on cancer patients show that radiation can cause an increase in bitterness and metal taste [in cancer patients] leading to discomfort in the oral cavity. In body, free radicals then can cause lipid peroxidation process. Lipid peroxidation is an oxidative destruction of polyunsaturated fatty acid producing malondialdehyde (MDA. Purpose: This study aimed to determine the effects of radiation on changes in the taste sensation of sour, salty, sweet, bitter, umami, and spicy as well as the levels of MDA serum in radiographers. Method: This study was an observational laboratory research using post- test control design. Samples were selected using simple random sampling technique. The samples were seven radiographers who have been working for five years in the laboratory and radiographic units in Surabaya. Result: Based on the results of statistical tests, it showed that there were no differences in the sensitivity of all tastes between the groups tested. Moreover, the results also depicted considerable value for the sour taste was 0.550, the saltiness was 0.775, the sweetness was 0.294, the bitter taste was 0.065, the umami taste was 0.705, and the spicy taste was 0.319 (p>0.05. However, the dramatic increase was higlighted in levels of MDA serum with a significant value of 0.065 (p>0.005. Conclusion. There were no changes in the sensitivity of sour, salty, sweet, bitter, umami, and spicy tastes, but there was a significant increased in level of MDA serum in the radiographers compared to the control group.

  14. Sour and duke cherry viruses in South-West Europe

    Directory of Open Access Journals (Sweden)

    Rodrigo PÉREZ-SÁNCHEZ

    2017-05-01

    Full Text Available This study investigated the phytosanitary status of sour and duke cherry genetic resources in the Iberian Peninsula, and the incidence and leaf symptoms induced by the Prunus necrotic ringspot virus (PNRSV, Prune dwarf virus (PDV and Apple chlorotic leaf spot virus (ACLSV. Young leaf samples were taken from 204 sour and duke cherry trees belonging to ten cultivars, and were assayed by DAS-ELISA. Samples positive for any of the three viruses were also tested by RT-PCR. To associate the leaf symptoms with virus presence, 50 mature leaves from each infected tree were visually inspected during the summer. The ELISA and RT-PCR results indicated that 63% of the cherry trees were infected by at least one of these viruses. PNRSV occurred in all cultivars sampled and presented the highest infection rate (46%, followed by PDV (31% and ACLSV (6%. Many trees, (60 to 100%, were asymptomatic while harbouring single and mixed virus infections. The leaf symptoms associated with the viruses included chlorotic and dark brown necrotic ringspots on secondary veins and interveinal regions, for PNRSV, generalized chlorosis around the midveins, for PDV, chlorotic and reddish necrotic ringspots, for ACLSV, and generalized interveinal chlorosis, for mixed PNRSV and PDVinfections.

  15. Organic and inorganic species in produced water: Implications for water reuse

    Science.gov (United States)

    Kharaka, Yousif K.; Rice, Cynthia A.

    2004-01-01

    Currently 20-30 billion barrels of formation water are co-produced annually in the USA with conventional oil and natural gas. The large database on the geochemistry of this produced water shows salinities that vary widely from ~5,000 to >350,000 mg/L TDS. Chloride, Na and Ca are generally the dominant ions, and concentrations of Fe, Mn, B, NH3 and dissolved organics, including, BTEX, phenols and poly aromatic hydrocarbons (PAHs) may be relatively high. Hazardous concentrations of NORMs, including Ra-226 and Rn-222 have been reported in produced water from several states.Coal-bed methane (CBM) wells currently produce close to a billion barrels of water and deliver ~8% of total natural gas. The salinity of this produced water generally is lower than that of water from petroleum wells; salinity commonly is 1,000-20,000 mg/L, but ranges to150,000 mg/L TDS. Most CBM wells produce Na-HCO3-Cl type water that is low in trace metals and has no reported NORMs. This water commonly has no oil and grease and has relatively low DOC, but its organic composition has not been characterized in detail. The water is disposed of by injection into saline aquifers, through evaporation and/or percolation in disposal pits, road spreading, and surface discharge. Water that has an acceptable salinity and sodium absorption ratio (SAR) is considered acceptable for surface discharge and for injection into freshwater aquifers.As an alternative to costly disposal, low salinity produced water is being considered for reclamation, especially in the arid western USA. The cost of reclaiming this water to meet irrigation, industrial and drinking water standards was evaluated in a 10 gpm pilot field study at Placerita oil field, California. This produced water had a low salinity of ~8,000 mg/L, but high concentration of Si and organics. Removal of B, Si, NH3 and especially organics from this water proved difficult, and the estimated treatment cost was high at $0.08-$0.39/bbl for water treated for

  16. Fruit and snack consumption related to sweet, sour and salty taste preferences

    NARCIS (Netherlands)

    Sijtsema, S.J.; Reinders, M.J.; Hiller, S.; Guardia, D.

    2012-01-01

    Purpose – To better understand fruit consumption and its determinants this paper aims to explore the relationship between the consumption of different types of fruit and other snacks and consumer taste preferences for sweet, salty and sour is explored. Design/methodology/approach – Respondents

  17. Pollution Impact and Alternative Treatment for Produced Water

    Science.gov (United States)

    Hedar, Yusran; Budiyono

    2018-02-01

    Oil and gas exploration and production are two of the activities that potentially cause pollution and environmental damage. The largest waste generated from this activity is produced water. Produced water contains hazardous pollutants of both organic and inorganic materials, so that the produced water of oil and gas production cannot be discharged directly to the environment. Uncontrolled discharge can lead to the environmental damage, killing the life of water and plants. The produced water needs to be handled and fulfill the quality standards before being discharged to the environment. Several studies to reduce the contaminants in the produced water were conducted by researchers. Among them were gravity based separation - flotation, separation technique based on filtration, and biological process treatment. Therefore, some of these methods can be used as an alternative waste handling of produced water.

  18. Review of produced water recycle and beneficial reuse

    Energy Technology Data Exchange (ETDEWEB)

    Hum, F.; Tsang, P. [Calgary Univ., AB (Canada). Tomographic Imaging and Porous Media Laboratory; Harding, T. [Calgary Univ., AB (Canada). Dept. of Chemical and Petroleum Engineering; Kantzas, A. [Calgary Univ., AB (Canada). Tomographic Imaging and Porous Media Laboratory]|[Calgary Univ., AB (Canada). Dept. of Chemical and Petroleum Engineering

    2006-11-15

    Fresh water scarcity and increasing water demands are concerns facing jurisdictions around the world. A number of water management initiatives involving produced water recycling and reuse in Alberta and Canada will have a significant impact on sustainable development in Alberta. Produced water must first be treated to meet water quality requirements and regulatory guidelines for specific applications. This paper presented a comprehensive technical and economic review of commercially available water treatment technologies and discussed technical challenges in recycling produced water for steam generation and for commercial use. It provided an introduction to fresh water allocations and oil, gas and water production volumes in Alberta. In addition to research and development activities, the paper identified guidelines from Alberta Environment and the Energy and Utilities Board. Benefits of treated produced water were discussed. Desalination technologies include both distillation processes and membrane processes. The paper provided cost estimates based on a literature view and discussed the potential water treatment for south-east Alberta. The paper also offered a number of recommendations for further research. It was concluded that treating and recycling produced water for agriculture, irrigation, commercial and domestic uses are at early stages of research and development and that regulatory guidelines on water quality, health and safety for specific industries, ownership and transfer of produced water need to be developed in order to facilitate beneficial reuse of produced water. 57 refs., 7 tabs., 14 figs.

  19. Oilfield Produced Water Reuse and Reinjection with Membrane

    Directory of Open Access Journals (Sweden)

    Siagian Utjok W.R.

    2018-01-01

    Full Text Available Produced water has become a global environmental issue due to its huge volume and toxicity that may pose detrimental effects on receiving environment. Several approaches have been proposed to provide a strategy for produced water handling such as reinjection, reuse, or discharge. With various advantages, membrane technology has been increasingly used in produced water treatment replacing the conventional technologies. However, fouling is a major drawback of membrane processes in this application which needs to be controlled. This paper gives an overview and comparison of different produced water management. Special attention is given to produced water treatment for reuse purpose. Furthermore, the use of membrane processes in produced water reuse including performance, challenges, and future outlook are discussed.

  20. Pollution Impact and Alternative Treatment for Produced Water

    Directory of Open Access Journals (Sweden)

    Hedar Yusran

    2018-01-01

    Full Text Available Oil and gas exploration and production are two of the activities that potentially cause pollution and environmental damage. The largest waste generated from this activity is produced water. Produced water contains hazardous pollutants of both organic and inorganic materials, so that the produced water of oil and gas production cannot be discharged directly to the environment. Uncontrolled discharge can lead to the environmental damage, killing the life of water and plants. The produced water needs to be handled and fulfill the quality standards before being discharged to the environment. Several studies to reduce the contaminants in the produced water were conducted by researchers. Among them were gravity based separation - flotation, separation technique based on filtration, and biological process treatment. Therefore, some of these methods can be used as an alternative waste handling of produced water.

  1. Characterization of Soluble Organics in Produced Water

    Energy Technology Data Exchange (ETDEWEB)

    Bostick, D.T.

    2002-01-16

    Soluble organics in produced water and refinery effluents represent treatment problems for the petroleum industry. Neither the chemistry involved in the production of soluble organics nor the impact of these chemicals on total effluent toxicity is well understood. The U.S. Department of Energy provides funding for Oak Ridge National Laboratory (ORNL) to support a collaborative project with Shell, Chevron, Phillips, and Statoil entitled ''Petroleum and Environmental Research Forum project (PERF 9844: Manage Water-Soluble Organics in Produced Water''). The goal of this project, which involves characterization and evaluation of these water-soluble compounds, is aimed at reducing the future production of such contaminants. To determine the effect that various drilling conditions might have on water-soluble organics (WSO) content in produced water, a simulated brine water containing the principal inorganic components normally found in Gulf of Mexico (GOM) brine sources was prepared. The GOM simulant was then contacted with as-received crude oil from a deep well site to study the effects of water cut, produced-water pH, salinity, pressure, temperature, and crude oil sources on the type and content of the WSO in produced water. The identities of individual semivolatile organic compounds (SVOCs) were determined in all as-received crude and actual produced water samples using standard USEPA Method (8270C) protocol. These analyses were supplemented with the more general measurements of total petroleum hydrocarbon (TPH) content in the gas (C{sub 6}-C{sub 10}), diesel (C{sub 10}-C{sub 20}), and oil (C{sub 20}-C{sub 28}) carbon ranges as determined by both gas chromatographic (GC) and infrared (IR) analyses. An open liquid chromatographic procedure was also used to differentiate the saturated hydrocarbon, aromatic hydrocarbon, and polar components within the extractable TPH. Inorganic constituents in the produced water were analyzed by ion

  2. Produced water treatment methods for SAGD

    Energy Technology Data Exchange (ETDEWEB)

    Minnich, K. [Veolia Water Solutions and Technologies, Mississauga, ON (Canada)

    2008-07-01

    Produced water treatment methods for steam assisted gravity drainage (SAGD) processes were presented. Lime softening is used to remove sludge before weak acid cation processes. However, the process is not reliable in cold climates, and disposal of the sludge is now posing environmental problems in Alberta. High pH MVC evaporation processes use sodium hydroxide (NaOH) additions to prevent silica scaling. However the process produces silica wastes that are difficult to dispose of. The sorption slurry process was designed to reduce the use of caustic soda and develop a cost-effective method of disposing evaporator concentrates. The method produces 98 per cent steam quality for SAGD injection. Silica is sorbed onto crystals in order to prevent silica scaling. The evaporator concentrate from the process is suitable for on- and off-site deep well disposal. The ceramic membrane process was designed to reduce the consumption of chemicals and improve the reliability of water treatment processes. The ion exchange desilication process uses 80 per cent less power and produces 80 per cent fewer CO{sub 2} emissions than MVC evaporators. A comparative operating cost evaluation of various electric supply configurations and produced water treatment processes was also included, as well as an analysis of produced water chemistry. tabs., figs.

  3. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    International Nuclear Information System (INIS)

    Ray W. Sheldon

    2001-01-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (stripper gas water) which are predominantly water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program is intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research is to determine appropriate guidelines for field trials by accurately

  4. Sour gas map of Alberta and British Columbia

    International Nuclear Information System (INIS)

    2000-01-01

    Geographic locations of sour gas wells in Alberta and British Columbia are shown (by geographic coordinates) on a large-size fold-out map issued as a supplement to the July issue of Oilweek Magazine. Pools are color coded based on hydrogen sulphide content. Five classes are recognized, i. e.: hydrogen sulphide content less than one percent; between one and 4.9 per cent; between five and 9.9 per cent; between ten and 29.9 per cent ; and hydrogen sulphide content exceeding 30 per cent. The locations of gas processing plants with sulphur recovery are also identified

  5. Management of Reclaimed Produced Water in the Rocky Mountain States Enhanced with the Expanded U.S. Geological Survey Produced Waters Geochemical Database

    Science.gov (United States)

    Gans, K. D.; Blondes, M. S.; Reidy, M. E.; Conaway, C. H.; Thordsen, J. J.; Rowan, E. L.; Kharaka, Y. K.; Engle, M.

    2016-12-01

    The Rocky Mountain states; Wyoming, Colorado, Montana, New Mexico and Utah produce annually approximately 470,000 acre-feet (3.66 billion barrels) of produced water - water that coexists with oil and gas and is brought to the surface with the pumping of oil and gas wells. Concerns about severe drought, groundwater depletion, and contamination have prompted petroleum operators and water districts to examine the recycling of produced water. Knowledge of the geochemistry of produced waters is valuable in determining the feasibility of produced water reuse. Water with low salinity can be reclaimed for use inside and outside of the petroleum industry. Since a great proportion of petroleum wells in the Rocky Mountain states, especially coal-bed methane wells, have produced water with relatively low salinity (generally oil recovery, and even for municipal uses, such as drinking water. The USGS Produced Waters Geochemical Database, available at http://eerscmap.usgs.gov/pwapp, has 60,000 data points in this region (this includes 35,000 new data points added to the 2002 database) and will facilitate studies on the management of produced water for reclamation in the Rocky Mountain region. Expanding on the USGS 2002 database, which contains geochemical analyses of major ions and total dissolved solids, the new data also include geochemical analyses of minor ions and stable isotopes. We have added an interactive web map application which allows the user to filter data on chosen fields (e.g. TDS data set can provide critical insight for better management of produced waters in water-constrained regions of the Rocky Mountains.

  6. Produced water radionuclide hazard/risk assessment, Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton, L.D.; Meinhold, A.F.; Nagy, J.

    1991-06-01

    Petroleum production may be accompanied by the production of saline water, called produced water.'' Produced water discharged into freshwater streams, estuaries, coastal and outer continental shelf waters can contained enhanced levels of radium isotopes. This document reports on the first phase of a study to estimate the risk to human health and the environment from radium discharged in produced water. The study involved five major steps: (1) evaluate the usefulness of available produced water outfall data for developing estimates of radium environmental concentrations; (2) review the literature on the bioaccumulation of radium by aquatic organism; (3) review the literature on the effects of radiation on aquatic organisms; (4) review the information available concerning the human health risks associated with exposure to Ra-226 and Ra-228 and (5) perform a conservative, screening-level assessment of the health and environmental risks posed by Ra-226 and Ra-228 discharged in produced waters. A screening-level analysis was performed to determine whether radium discharged to coastal Louisiana in produced waters presents potential health or environmental risks requiring further study. This conservative assessment suggested that no detectable impact on populations of fish, molluscs or crustaceans from radium discharged in produced waters is likely. The analysis also suggested that there is a potential for risk were an individual to ingest a large amount of seafood harvested near a produced water discharge point over a lifetime. The number of excess cancers predicted per year under a conservative scenario is comparable to those expected to result from background concentrations of radium.

  7. Produced water radionuclide hazard/risk assessment, Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton, L.D.; Meinhold, A.F.; Nagy, J.

    1991-06-01

    Petroleum production may be accompanied by the production of saline water, called ``produced water.`` Produced water discharged into freshwater streams, estuaries, coastal and outer continental shelf waters can contained enhanced levels of radium isotopes. This document reports on the first phase of a study to estimate the risk to human health and the environment from radium discharged in produced water. The study involved five major steps: (1) evaluate the usefulness of available produced water outfall data for developing estimates of radium environmental concentrations; (2) review the literature on the bioaccumulation of radium by aquatic organism; (3) review the literature on the effects of radiation on aquatic organisms; (4) review the information available concerning the human health risks associated with exposure to Ra-226 and Ra-228 and (5) perform a conservative, screening-level assessment of the health and environmental risks posed by Ra-226 and Ra-228 discharged in produced waters. A screening-level analysis was performed to determine whether radium discharged to coastal Louisiana in produced waters presents potential health or environmental risks requiring further study. This conservative assessment suggested that no detectable impact on populations of fish, molluscs or crustaceans from radium discharged in produced waters is likely. The analysis also suggested that there is a potential for risk were an individual to ingest a large amount of seafood harvested near a produced water discharge point over a lifetime. The number of excess cancers predicted per year under a conservative scenario is comparable to those expected to result from background concentrations of radium.

  8. Produced water radionuclide hazard/risk assessment, Phase 1

    International Nuclear Information System (INIS)

    Hamilton, L.D.; Meinhold, A.F.; Nagy, J.

    1991-06-01

    Petroleum production may be accompanied by the production of saline water, called ''produced water.'' Produced water discharged into freshwater streams, estuaries, coastal and outer continental shelf waters can contained enhanced levels of radium isotopes. This document reports on the first phase of a study to estimate the risk to human health and the environment from radium discharged in produced water. The study involved five major steps: (1) evaluate the usefulness of available produced water outfall data for developing estimates of radium environmental concentrations; (2) review the literature on the bioaccumulation of radium by aquatic organism; (3) review the literature on the effects of radiation on aquatic organisms; (4) review the information available concerning the human health risks associated with exposure to Ra-226 and Ra-228 and (5) perform a conservative, screening-level assessment of the health and environmental risks posed by Ra-226 and Ra-228 discharged in produced waters. A screening-level analysis was performed to determine whether radium discharged to coastal Louisiana in produced waters presents potential health or environmental risks requiring further study. This conservative assessment suggested that no detectable impact on populations of fish, molluscs or crustaceans from radium discharged in produced waters is likely. The analysis also suggested that there is a potential for risk were an individual to ingest a large amount of seafood harvested near a produced water discharge point over a lifetime. The number of excess cancers predicted per year under a conservative scenario is comparable to those expected to result from background concentrations of radium

  9. ANAEROBIC BIOLOGICAL TREATMENT OF PRODUCED WATER; TOPICAL

    International Nuclear Information System (INIS)

    John R. Gallagher

    2001-01-01

    During the production of oil and gas, large amounts of water are brought to the surface and must be disposed of in an environmentally sensitive manner. This is an especially difficult problem in offshore production facilities where space is a major constraint. The chief regulatory criterion for produced water is oil and grease. Most facilities have little trouble meeting this criterion using conventional oil-water separation technologies. However, some operations have significant amounts of naphthenic acids in the water that behave as oil and grease but are not well removed by conventional technologies. Aerobic biological treatment of naphthenic acids in simulated-produced water has been demonstrated by others; however, the system was easily overloaded by the large amounts of low-molecular-weight organic acids often found in produced waters. The objective of this research was to determine the ability of an anaerobic biological system to treat these organic acids in a simulated produced water and to examine the potential for biodegradation of the naphthenic acids in the anaerobic environment. A small fixed-film anaerobic biological reactor was constructed and adapted to treat a simulated produced water. The bioreactor was tubular, with a low-density porous glass packing material. The inocula to the reactor was sediment from a produced-water holding pond from a municipal anaerobic digester and two salt-loving methanogenic bacteria. During start-up, the feed to the reactor contained glucose as well as typical produced-water components. When glucose was used, rapid gas production was observed. However, when glucose was eliminated and the major organic component was acetate, little gas was generated. Methane production from acetate may have been inhibited by the high salt concentrations, by sulfide, or because of the lack, despite seeding, of microbes capable of converting acetate to methane. Toluene, a minor component of the produced water (0.1 g/L) was removed in the

  10. Beneficial Reuse of San Ardo Produced Water

    Energy Technology Data Exchange (ETDEWEB)

    Robert A. Liske

    2006-07-31

    This DOE funded study was performed to evaluate the potential for treatment and beneficial reuse of produced water from the San Ardo oilfield in Monterey County, CA. The potential benefits of a successful full-scale implementation of this project include improvements in oil production efficiency and additional recoverable oil reserves as well as the addition of a new reclaimed water resource. The overall project was conducted in two Phases. Phase I identified and evaluated potential end uses for the treated produced water, established treated water quality objectives, reviewed regulations related to treatment, transport, storage and use of the treated produced water, and investigated various water treatment technology options. Phase II involved the construction and operation of a small-scale water treatment pilot facility to evaluate the process's performance on produced water from the San Ardo oilfield. Cost estimates for a potential full-scale facility were also developed. Potential end uses identified for the treated water include (1) agricultural use near the oilfield, (2) use by Monterey County Water Resources Agency (MCWRA) for the Salinas Valley Water Project or Castroville Seawater Intrusion Project, (3) industrial or power plant use in King City, and (4) use for wetlands creation in the Salinas Basin. All of these uses were found to have major obstacles that prevent full-scale implementation. An additional option for potential reuse of the treated produced water was subsequently identified. That option involves using the treated produced water to recharge groundwater in the vicinity of the oil field. The recharge option may avoid the limitations that the other reuse options face. The water treatment pilot process utilized: (1) warm precipitation softening to remove hardness and silica, (2) evaporative cooling to meet downstream temperature limitations and facilitate removal of ammonia, and (3) reverse osmosis (RO) for removal of dissolved salts, boron

  11. Development of compact mutants in apple and sour cherry

    International Nuclear Information System (INIS)

    Zagaja, S.W.; Przybyla, A.; Machnik, B.

    1982-01-01

    During the period 1973 - 79 studies were conducted with the aim of developing compact mutants in apple and cherry cultivars and in apple vegetative rootstocks. During the investigations the effect of the dose of gamma rays on frequency of the mutants was studied. Attempts were also made to evolve a micropropagation technique adapted to propagate P 2 and P 22 apple rootstocks, as an aid in mutation breeding. Several mutants were produced in all the material studied, but none of them have yet reached a sufficient developmental stage to enable their complete assessment. On the basis of the results obtained so far the following conclusions can be drawn: higher doses of irradiation resulted in higher frequency of mutants in most apple cultivars and apple rootstocks; in sour cherries the effect of dose depended on the cultivars. Among V 1 shoots developed from sleeping buds on irradiated scion wood, compact mutants were found; their frequency, however, was about 60% lower than among V 1 shoots developed directly from irradiated dormant buds. In apple rootstocks A 2 and M 26 several dwarfed mutants were found; some of these produced thorny plants and some had lower rooting ability; both these characteristics are inferior from the practical point of view. Multiplication and rooting media for in vitro propagation of apple rootstocks, worked out for M 26, were found unsuitable for the rootstocks P 2 and P 22; modifications made in the growth substance composition of the above media enabled satisfactory propagation to be obtained. (author)

  12. Corrosion behaviour of steels and CRA in sour gas environments

    Energy Technology Data Exchange (ETDEWEB)

    Lara, M. Alvarez de; Lancha, A.M.; Hernandez, F.; Gomez-Briceno, D. [CIEMAT, Avenida Complutense 22, 28040 Madrid (Spain); Coca, P. [ELCOGAS, S.A., C.T. GICC Puertollano, Carretera de Calzada de Calatrava a Puertollano, km 27, 13500 Puertollano, Ciudad Real (Spain)

    2004-07-01

    The ELCOGAS power plant in Puertollano (Spain), with 335 MWe (ISO conditions), is an Integrated Gasification Combined Cycle (IGCC) plant built to demonstrate both the technical and economic feasibility of this alternative for clean generation of electricity from coal. IGCC technology is based on a coal gasification process, namely the conversion of coal into combustible gas, which is then subjected to an exhaustive cleaning process. The result is a synthetic gas, virtually free of pollutants that can be burned with a high efficiency in a combined cycle electricity-generating unit. Basically, the ELCOGAS plant consists of three islands jointly designed and integrated into the process: gasification island, air separation island and combined cycle island. In the gasification island, the gas from the gasifier is cleaned (de-dusted and washed) and desulfurized before being sent to the combined cycle island. The washing system consists of a Venturi scrubber with a separator where halogens and alkalis (NH{sub 3}, HCl, HF) are removed from the previously de-dusted gas by means of the wash water. The halogens and alkalis removed are then stripped from the wash water as stripped gas, which is a sour gas. The coal-gas coming from the separator proceeds to sulphur removal in a MDEA system and then, the clean gas (mainly CO, H{sub 2}) is sent to the combined cycle plant. As COS is a significant part of the sulphur containing gases in the coal gas, hydrolysis of the COS to H{sub 2}S takes place before the desulfurization stage, since MDEA is a selective amine for H{sub 2}S. There are many important areas related to materials corrosion within the gas cleaning system. In the ELCOGAS plant carbon steels, austenitic stainless steels and nickel based alloys, such as AISI 316Ti, AISI 904L and Hastelloy C276, are used in the Venturi, the water separator and the strippers. AISI 316Ti is used for the gas piping from the separator to the COS hydrolysis system. Laboratory tests to evaluate

  13. New highly divergent Plum pox virus isolates infecting sour cherry in Russia.

    Science.gov (United States)

    Chirkov, Sergei; Ivanov, Peter; Sheveleva, Anna; Zakubanskiy, Alexander; Osipov, Gennady

    2017-02-01

    Unusual Plum pox virus (PPV) isolates (named Tat isolates) were discovered on sour cherry (Prunus cerasus) in Russia. They failed to be recognized by RT-PCR using commonly employed primers specific to the strains C or CR (the only ones that proved able to infect sour cherry) as well as to the strains M and W. Some of them can be detected by RT-PCR using the PPV-D-specific primers P1/PD or by TAS-ELISA with the PPV-C-specific monoclonal antibody AC. Phylogenetic analysis of the 3'-terminal genomic region assigned the Tat isolates into the cluster of cherry-adapted strains. However, they grouped separately from the C and CR strains and from each other as well. The sequence divergence of the Tat isolates is comparable to the differences between the known PPV strains. They may represent new group(s) of cherry-adapted isolates which do not seem to belong to any known strain of the virus. Copyright © 2016. Published by Elsevier Inc.

  14. Heptyl vicianoside and methyl caramboside from sour star fruit.

    Science.gov (United States)

    Yang, Dan; Jia, Xuchao; Xie, Haihui

    2018-04-23

    Two new alkyl glycosides, heptyl vicianoside (1) and methyl 2-O-β-d-fucopyranosyl-α-l-arabinofuranoside (methyl caramboside, 4), were isolated from the sour fruit of Averrhoa carambola L. (Oxalidaceae), along with octyl vicianoside (2), cis-3-hexenyl rutinoside (3), and methyl α-d-fructofuranoside (5). Their structures were determined by spectroscopic and chemical methods. Compounds 2, 3, and 5 were obtained from the genus Averrhoa for the first time. All the compounds were evaluated for in vitro α-glucosidase, pancreatic lipase, and acetylcholinesterase inhibitory activities, but none of them were potent.

  15. Effect of ultrasound on some chemical and microbiological properties of sour cherry juice by response surface methodology.

    Science.gov (United States)

    Türken, Tuğba; Erge, Hande S

    2017-09-01

    In this study, it is aimed to determine effect of ultrasonication on some chemical and microbiological properties of sour cherry juice by response surface methodology, since ultrasound is known as an alternative method for thermal food processing. Sour cherry juice was sonicated at varying amplitude levels (50, 75, 100%); moderate temperatures (20, 30, 40 ℃); and treatment times of 2, 6, 10 min at a constant frequency of 20 kHz. Different ultrasonication amplitudes, temperatures, and times had no significant effect on pH,°Bx, and titratable acidity. A significant increase in total monomeric anthocyanins was observed as the amplitude level and temperature increased (p < 0.01). An increase in the total phenolics was also obtained as the temperature increased (p < 0.05). The effect of amplitude level on antioxidant capacity of sour cherry juice was also found significant (p < 0.05). Color parameters (L*, a*, b*, C, h) generally increased by increasing temperature, amplitude level, and treatment time. It was determined that Escherichia coli O157:H7 significantly affected by temperature and treatment time (p < 0.05).

  16. Effects of aqueous extracts of dried calyx of sour tea (Hibiscus sabdariffa L. on polygenic dyslipidemia: A randomized clinical trial

    Directory of Open Access Journals (Sweden)

    Majid Hajifaraji

    2017-12-01

    Full Text Available Objective: Dyslipidemia has been considered as a major risk factor for coronary heart disease. Alternative medicine has a significant role in treatment of dyslipidemia. There are controversial findings regarding the effects of sour tea on dyslipidemia. The aim of this study was to evaluate the impact of aqueous extract of dried calyx of sour tea on polygenic dyslipidemia. Materials and Methods: This clinical trial was done on 43 adults (30-60 years old with polygenic dyslipidemia that were randomly assigned to the intervention and control groups. The control group was trained in lifestyle modifications at baseline. The intervention group was trained for lifestyle modifications at baseline and received two cups of sour tea daily, and both groups were followed up for 12 weeks. Lipid profile was evaluated at baseline, and six and 12 weeks following the intervention. In addition, dietary and physical activity assessed at baseline for twelve weeks. Results: Mean concentration of total cholesterol, HDL-C and LDL-C significantly decreased by up to 9.46%, 8.33%, and 9.80%, respectively, after 12 weeks in the intervention group in comparison to their baseline values. However, LDL-C/HDL-C ratio significantly increased  by up to 3.15%, following 12 weeks in the control group in comparison to their baseline values. This study showed no difference in lipid profiles between the two groups, except for HDL-C concentrations. Conclusion: sour tea may have significant positive effects on lipid profile of polygenic dyslipidemia subjects and these effect might be attributed to its anthocyanins and inflation factor content. Therefore, sour tea intake with recommended dietary patterns and physical activity can be useful in regulation of lipid profile in patients with polygenic dyslipidemia.

  17. Recycling produced water for algal cultivation for biofuels

    Energy Technology Data Exchange (ETDEWEB)

    Neal, Justin N. [Los Alamos National Laboratory; Sullivan, Enid J. [Los Alamos National Laboratory; Dean, Cynthia A. [Los Alamos National Laboratory; Steichen, Seth A. [Los Alamos National Laboratory

    2012-08-09

    Algal growth demands a continuous source of water of appropriate salinity and nutritional content. Fresh water sources are scarce in the deserts of the Southwestern United States, hence, salt water algae species are being investigated as a renewable biofuel source. The use of produced water from oil wells (PW) could offset the demand for fresh water in cultivation. Produced water can contain various concentrations of dissolved solids, metals and organic contaminants and often requires treatment beyond oil/water separation to make it suitable for algae cultivation. The produced water used in this study was taken from an oil well in Jal, New Mexico. An F/2-Si (minus silica) growth media commonly used to cultivate Nannochloropsis salina 1776 (NS 1776) was prepared using the produced water (F/2-Si PW) taking into account the metals and salts already present in the water. NS 1776 was seeded into a bioreactor containing 5L of the (F/2-Si PW) media. After eleven days the optical density at 750 nm (an indicator of algal growth) increased from 0 to 2.52. These results indicate algae are able to grow, though inhibited when compared with non-PW media, in the complex chemical conditions found in produced water. Savings from using nutrients present in the PW, such as P, K, and HCO{sub 3}{sup -}, results in a 44.38% cost savings over fresh water to mix the F/2-Si media.

  18. Phytoplasmas in apricot, peach and sour cherry orchards in East Bohemia, Czech Republic

    Czech Academy of Sciences Publication Activity Database

    Ludvíková, H.; Fránová, Jana; Suchá, J.

    2011-01-01

    Roč. 64, Suppl. (2011), s. 67-68 ISSN 1721-8861 R&D Projects: GA MŠk OC09021 Institutional research plan: CEZ:AV0Z50510513 Keywords : Candidatus Phytoplasma prunorum * PCR/RFLP * apricot, peach and sour cherry orchards Subject RIV: EE - Microbiology, Virology Impact factor: 0.592, year: 2011

  19. Produced water volumes and management practices in the United States.

    Energy Technology Data Exchange (ETDEWEB)

    Clark, C. E.; Veil, J. A. (Environmental Science Division)

    2009-09-01

    Produced water volume generation and management in the United States are not well characterized at a national level. The U.S. Department of Energy (DOE) asked Argonne National Laboratory to compile data on produced water associated with oil and gas production to better understand the production volumes and management of this water. The purpose of this report is to improve understanding of produced water by providing detailed information on the volume of produced water generated in the United States and the ways in which produced water is disposed or reused. As the demand for fresh water resources increases, with no concomitant increase in surface or ground water supplies, alternate water sources, like produced water, may play an important role. Produced water is water from underground formations that is brought to the surface during oil or gas production. Because the water has been in contact with hydrocarbon-bearing formations, it contains some of the chemical characteristics of the formations and the hydrocarbons. It may include water from the reservoir, water previously injected into the formation, and any chemicals added during the production processes. The physical and chemical properties of produced water vary considerably depending on the geographic location of the field, the geologic formation, and the type of hydrocarbon product being produced. Produced water properties and volume also vary throughout the lifetime of a reservoir. Produced water is the largest volume by-product or waste stream associated with oil and gas exploration and production. Previous national produced water volume estimates are in the range of 15 to 20 billion barrels (bbl; 1 bbl = 42 U.S. gallons) generated each year in the United States (API 1988, 2000; Veil et al. 2004). However, the details on generation and management of produced water are not well understood on a national scale. Argonne National Laboratory developed detailed national-level information on the volume of produced

  20. Terminal acidic shock inhibits sour beer bottle conditioning by Saccharomyces cerevisiae.

    Science.gov (United States)

    Rogers, Cody M; Veatch, Devon; Covey, Adam; Staton, Caleb; Bochman, Matthew L

    2016-08-01

    During beer fermentation, the brewer's yeast Saccharomyces cerevisiae experiences a variety of shifting growth conditions, culminating in a low-oxygen, low-nutrient, high-ethanol, acidic environment. In beers that are bottle conditioned (i.e., carbonated in the bottle by supplying yeast with a small amount of sugar to metabolize into CO2), the S. cerevisiae cells must overcome these stressors to perform the ultimate act in beer production. However, medium shock caused by any of these variables can slow, stall, or even kill the yeast, resulting in production delays and economic losses. Here, we describe a medium shock caused by high lactic acid levels in an American sour beer, which we refer to as "terminal acidic shock". Yeast exposed to this shock failed to bottle condition the beer, though they remained viable. The effects of low pH/high [lactic acid] conditions on the growth of six different brewing strains of S. cerevisiae were characterized, and we developed a method to adapt the yeast to growth in acidic beer, enabling proper bottle conditioning. Our findings will aid in the production of sour-style beers, a trending category in the American craft beer scene. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Practices and prospect of petroleum engineering technologies in ultra-deep sour gas reservoirs, Yuanba Gasfield, Sichuan Basin

    Directory of Open Access Journals (Sweden)

    Jin Xu

    2016-12-01

    Full Text Available Located in the Sichuan Basin, the Yuanba Gasfield is the deepest marine sour gas field among those developed in China so far. Its biohermal gas reservoir of the Upper Permian Changxing Fm is characterized by ultra depth, high content of hydrogen sulfide, medium–low porosity and permeability, and small reservoir thickness. Economic evaluation on it shows that horizontal well drilling is the only way to develop this gas reservoir efficiently and to reduce the total development investment. At present, the petroleum engineering technology for this type of ultra-deep sour gas reservoir is less applied in the world, so an ultra-deep horizontal well is subject to a series of petroleum engineering technology difficulties, such as safe and fast well drilling and completion, mud logging, well logging, downhole operation, safety and environmental protection. Based on the successful development experience of the Puguang Gasfield, therefore, Sinopec Southwest Petroleum Engineering Co., Ltd. took the advantage of integrated engineering geology method to carry out specific technical research and perform practice diligently for 7 years. As a result, 18 key items of technologies for ultra-deep sour gas reservoirs were developed, including horizontal-well drilling speed increasing technology, horizontal-well mud logging and well logging technology, downhole operation technology, and safety and environmental protection technology. These technologies were applied in 40 wells during the first and second phases of productivity construction of the Yuanba Gasfield. All the 40 wells have been built into commercial gas wells, and the productivity construction goal of 3.4 billion m3 purified gas has also been achieved. These petroleum engineering technologies for ultra-deep sour gas fields play a reference role in exploring and developing similar gas reservoirs at home and abroad.

  2. Design of small diameter HT/HP sour service reeled rigid pipelines

    Energy Technology Data Exchange (ETDEWEB)

    Carneiro, Daniel; Gouveia, Joao; Tardelli, Luciano [Tecnitas, Rio de Janeiro, RJ (Brazil)], e-mail: daniel.carneiro@br.bureauveritas.com; Parrilha, Rafael [Bureau Veritas Group, London (United Kingdom); Oazen, Eduardo; Cardoso, Carlos [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2009-12-19

    The paper presents an overview of the challenges overcome in the engineering design of two 219 mm diameter, 6 km length oil production pipelines, to be installed by reeling at Espirito Santo Basin, offshore Brazilian coast in 1500 m water depth. The high temperature and high pressure (HT/HP) operating conditions and sour content associated with the small diameter required to single well oil production would usually lead to flexible flow line solution in Brazilian fields. The decision of employing small diameter thick-walled rigid C-Mn steel pipelines with thick thermal insulation made necessary extensive engineering work to achieve a safe and robust thermal expansion control arrangement, including the design of walking mitigation and buckle initiation apparatus; a feasible weld acceptance criterion covering both high cycle fatigue due to pipe lay and vortex induced vibration (VIV) at free spans, and high strain low cycle fatigue and fracture growth induced by reeling installation and in-service lateral buckling. Several studies were performed using highly non-linear three-dimensional finite element models considering: pipe-soil interaction with full 3D seabed bathymetry; load history maintained from pipe lay to operational cycles, including temperature transient effects; high plastic strains (including steel properties de-rating due to high temperature) and section ovalization; mechanical contact between pipe and appurtenances during both installation and operational phases. Pipe-soil interaction comprised embedment considering dynamic effects of pipe lay and full non-linear lateral and axial response curves including break-out and residual resistance. Strain concentration factors due to field joints were evaluated using detailed solid models considering non-linear response of both steel and insulation materials. Susceptibility to VIV at free spans was assessed considering post loaded deformed span natural frequencies, including multi-span interaction effects and

  3. Inhibitory effect of sour pomegranate sauces on some green vegetables and kisir.

    Science.gov (United States)

    Karabiyikli, Seniz; Kisla, Duygu

    2012-04-16

    In this study, the antimicrobial effects of both traditional and commercial pomegranate sour sauce samples on some green vegetables and also on "kısır" which is a popular and traditional appetizer in Turkey were investigated. The inhibitory effect of the pomegranate products on the naturally existing bacterial microflora of lettuce, spring onion, parsley and kısır were analyzed. Also, all these food samples were inoculated with Staphylococcus aureus (ATCC-25923) and Escherichia coli O157:H7 (ATCC-43895) and antimicrobial effect of the pomegranate products on the inoculated microflora was detected. All the food samples were treated with pomegranate products for different time periods and the effect of treatment time was investigated. pH and titratable acidity values of the traditional and commercial pomegranate sour sauce samples were detected. The results showed that although the pomegranate products had an antimicrobial effect on the natural bacterial microflora of the food samples, the effect on inoculated food samples was more prominent and additionally the application time was found to be a crucial parameter for both cases. Copyright © 2012 Elsevier B.V. All rights reserved.

  4. Presynaptic (Type III) cells in mouse taste buds sense sour (acid) taste.

    Science.gov (United States)

    Huang, Yijen A; Maruyama, Yutaka; Stimac, Robert; Roper, Stephen D

    2008-06-15

    Taste buds contain two types of cells that directly participate in taste transduction - receptor (Type II) cells and presynaptic (Type III) cells. Receptor cells respond to sweet, bitter and umami taste stimulation but until recently the identity of cells that respond directly to sour (acid) tastants has only been inferred from recordings in situ, from behavioural studies, and from immunostaining for putative sour transduction molecules. Using calcium imaging on single isolated taste cells and with biosensor cells to identify neurotransmitter release, we show that presynaptic (Type III) cells specifically respond to acid taste stimulation and release serotonin. By recording responses in cells isolated from taste buds and in taste cells in lingual slices to acetic acid titrated to different acid levels (pH), we also show that the active stimulus for acid taste is the membrane-permeant, uncharged acetic acid moiety (CH(3)COOH), not free protons (H(+)). That observation is consistent with the proximate stimulus for acid taste being intracellular acidification, not extracellular protons per se. These findings may also have implications for other sensory receptors that respond to acids, such as nociceptors.

  5. Health risk assessment for radium discharged in produced waters

    International Nuclear Information System (INIS)

    Hamilton, L.D.; Meinhold, A.F.; Nagy, J.

    1991-01-01

    Produced water generated during the production of oil and gas can contain enhanced levels of radium. This naturally occurring radioactive material (NORM) is discharged into freshwater streams, estuarine, coastal and outer continental shelf waters. Large volumes of produced waters are discharged to coastal waters along the Gulf Coast of Louisiana. The Gulf of Mexico is an important producer of fish and shellfish, and there is concern that radium discharged to coastal Louisiana could contaminate fish and shellfish used by people for food, and present a significant increase in cancer risk. This paper describes a screening-level assessment of the potential cancer risks posed by radium discharged to coastal Louisiana in oil-field produced waters. This screening analysis was performed to determine if a more comprehensive and realistic assessment is necessary, and because of the conservative assumptions embedded in the analysis overestimates the risk associated with the discharge of radium in produced waters. Two isotopes of radium (Ra-226 and Ra-228) are the radionuclides of most concern in produced water in terms of potential human health effects

  6. Development of high-strength heavy-wall sour-service seamless line pipe for deep water by applying inline heat treatment

    Energy Technology Data Exchange (ETDEWEB)

    Arai, Y.; Kondo, K.; Hamada, M.; Hisamune, N.; Murao, N.; Murase, T.; Osako, H. [Sumitomo Metal Industries Ltd., Tokyo (Japan)

    2004-07-01

    This paper provided details of a new high-strength heavy-wall sour service seamless line pipe developed for use in deep water applications. Pig iron was processed in a blast furnace and refined. Molten steel was degassed to reduce impurities and poured into a continuous caster with a round mold. Billets were then heated in a walking-beam furnace and then pierced to form a hollow shell. The shell was then rolled to a specific thickness in a compact mandrel mill and rolled to a specified outer diameter by an extracting sizer. A heating furnace was used to improve the uniformity of the pipes. The heated pipes were then moved to a cooling zone, then rotated quickly while a high-pressured jet flow was injected inside the pipe at the same time as a slit laminar flow was applied to the outside of the pipe. Higher strength was achieved by using the high performance quenching device. It was noted that while pipes manufactured using the inline heat treatment process were able to achieve higher strengths, toughness was reduced. Metallurgical tests were conducted to improve the toughness value of the seamless pipe. Both the microstructure and the fracture surface of test specimens were examined using scanning electron microscopy. Results of the tests showed that lowering sulphur (S) and titanium (Ti) content improved the toughness properties of the pipes. It was concluded that control of microalloys is important to secure improved toughness for pipes manufactured using inline heat treatments. 5 tabs., 12 figs.

  7. The influence of sour taste and cold temperature in pharyngeal transit duration in patients with stroke

    Directory of Open Access Journals (Sweden)

    Paula Cristina Cola

    2010-03-01

    Full Text Available CONTEXT: The effect of sour taste and food temperature variations in dysphagic patients has not been entirely clarified. OBJECTIVE: To determine the effect of sour and cold food in the pharyngeal transit times of patients with stroke. METHODS: Patients participating in this study were 30 right-handed adults, 16 of which were male and 14 were female, aged 41 to 88 (average age 62.3 years with ictus varying from 1 to 30 days (median of 6 days. To analyze the pharyngeal transit time a videofluoroscopy swallow test was performed. Each patient was observed during swallow of a 5 mL paste bolus given by spoon, totaling four different stimuli (natural, cold, sour and cold sour, one at a time, room temperature (22ºC and cold (8ºC were used. Later, the tests were analyzed using specific software to measure bolus transit time during the pharyngeal phase. RESULTS: The results showed that the pharyngeal transit time was significantly shorter during swallow of cold sour bolus when compared with other stimuli. Conclusion - Sour taste stimuli associated to cold temperature cause significant change in swallowing patterns, by shortening the pharyngeal transit time, which may lead to positive effects in patients with oropharyngeal dysphagia.CONTEXTO: O efeito do sabor azedo e as variações da temperatura dos alimentos em indivíduos disfágicos, ainda não foi totalmente esclarecidos. OBJETIVO: Verificar o efeito do sabor azedo e da temperatura fria no tempo de trânsito faríngeo da deglutição em indivíduos após acidente vascular encefálico hemisférico isquêmico. MÉTODOS: Participaram deste estudo 30 indivíduos adultos, sendo 16 do gênero masculino e 14 do feminino, destros, com faixa etária variando de 41 a 88 anos (média de 62,3 anos e ictus que variou de 1 a 30 dias (mediana de 6 dias. Para analisar o tempo de trânsito faríngeo da deglutição foi realizado o exame de videofluoroscopia da deglutição. Cada indivíduo foi observado durante a

  8. Options for cleaning up subsurface contamination at Alberta sour gas plants

    International Nuclear Information System (INIS)

    Hardisty, P.; Dabrowski, T.L.

    1992-01-01

    At the conclusion of two major phases of a study on subsurface treatment technologies for Alberta sour gas plants, a candidate site was selected for a remediation technologies demonstration project. The plant has an extensive groundwater monitoring network in place, monitoring records for a period exceeding 10 years, ten recovery wells with aquifer test data and four reinjection wells. Hydrogeological exploration determined the presence and delineated a plume of free phase natural gas condensate. Aquifer remediation efforts at the site began in 1990 with the installation of recovery wells. Recovered groundwater was treated using a pilot scale air stripping system with pretreatment for iron, manganese and hardness. Dual pump system, water depression and free product skimmers were installed in the wells and tested. The nature and extent of contamination, study methodology, technology-dependent criteria, assessment of technology, and conceptual design are discussed for the three demonstration projects selected, which are enhanced soil vapour extraction with off-gas treatment, pump-and-treat with soil vapour extraction, biological treatment and air sparging, and treatment of dissolved process chemicals by advanced oxidation. 5 refs., 1 fig., 1 tab

  9. A review of crosslinked fracturing fluids prepared with produced water

    Directory of Open Access Journals (Sweden)

    Leiming Li

    2016-12-01

    Full Text Available The rapidly increasing implementations of oilfield technologies such as horizontal wells and multistage hydraulic fracturing, particularly in unconventional formations, have expanded the need for fresh water in many oilfield locations. In the meantime, it is costly for services companies and operators to properly dispose large volumes of produced water, generated annually at about 21 billion barrels in the United States alone. The high operating costs in obtaining fresh water and dealing with produced water have motivated scientists and engineers, especially in recent years, to use produced water in place of fresh water to formulate well treatment fluids. The objective of this brief review is to provide a summary of the up-to-date technologies of reusing oilfield produced water in preparations of a series of crosslinked fluids implemented mainly in hydraulic fracturing operations. The crosslinked fluids formulated with produced water include borate- and metal-crosslinked guar and derivatized guar fluids, as well as other types of crosslinked fluid systems such as crosslinked synthetic polymer fluids and crosslinked derivatized cellulose fluids. The borate-crosslinked guar fluids have been successfully formulated with produced water and used in oilfield operations with bottomhole temperatures up to about 250 °F. The produced water sources involved showed total dissolved solids (TDS up to about 115,000 mg/L and hardness up to about 11,000 mg/L. The metal-crosslinked guar fluids prepared with produced water were successfully used in wells at bottomhole temperatures up to about 250 °F, with produced water TDS up to about 300,000 mg/L and hardness up to about 44,000 mg/L. The Zr-crosslinked carboxymethyl hydroxypropyl guar (CMHPG fluids have been successfully made with produced water and implemented in operations with bottomhole temperatures at about 250+ °F, with produced water TDS up to about 280,000 mg/L and hardness up to about 91,000

  10. Bacterial diversity in water injection systems of Brazilian offshore oil platforms.

    Science.gov (United States)

    Korenblum, Elisa; Valoni, Erika; Penna, Mônica; Seldin, Lucy

    2010-01-01

    Biogenic souring and microbial-influenced corrosion is a common scenario in water-flooded petroleum reservoirs. Water injection systems are continuously treated to control bacterial contamination, but some bacteria that cause souring and corrosion can persist even after different treatments have been applied. Our aim was to increase our knowledge of the bacterial communities that persist in the water injection systems of three offshore oil platforms in Brazil. To achieve this goal, we used a culture-independent molecular approach (16S ribosomal RNA gene clone libraries) to analyze seawater samples that had been subjected to different treatments. Phylogenetic analyses revealed that the bacterial communities from the different platforms were taxonomically different. A predominance of bacterial clones affiliated with Gammaproteobacteria, mostly belonging to the genus Marinobacter (60.7%), were observed in the platform A samples. Clones from platform B were mainly related to the genera Colwellia (37.9%) and Achromobacter (24.6%), whereas clones obtained from platform C were all related to unclassified bacteria. Canonical correspondence analyses showed that different treatments such as chlorination, deoxygenation, and biocide addition did not significantly influence the bacterial diversity in the platforms studied. Our results demonstrated that the injection water used in secondary oil recovery procedures contained potentially hazardous bacteria, which may ultimately cause souring and corrosion.

  11. Treatment of Oil & Gas Produced Water.

    Energy Technology Data Exchange (ETDEWEB)

    Dwyer, Brian P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-02-01

    Production of oil and gas reserves in the New Mexico Four Corners Region results in large volumes of "produced water". The common method for handling the produced water from well production is re-injection in regulatory permitted salt water disposal wells. This is expensive (%7E $5/bbl.) and does not recycle water, an ever increasingly valuable commodity. Previously, Sandia National Laboratories and several NM small business tested pressure driven membrane-filtration techniques to remove the high TDS (total dissolved solids) from a Four Corners Coal Bed Methane produced water. Treatment effectiveness was less than optimal due to problems with pre-treatment. Inadequate pre-treatment allowed hydrocarbons, wax and biological growth to foul the membranes. Recently, an innovative pre-treatment scheme using ozone and hydrogen peroxide was pilot tested. Results showed complete removal of hydrocarbons and the majority of organic constituents from a gas well production water. ACKNOWLEDGEMENTS This report was made possible through funding from the New Mexico Small Business Administration (NMSBA) Program at Sandia National Laboratories. Special thanks to Juan Martinez and Genaro Montoya for guidance and support from project inception to completion. Also, special thanks to Frank McDonald, the small businesses team POC, for laying the ground work for the entire project; Teresa McCown, the gas well owner and very knowledgeable- fantastic site host; Lea and Tim Phillips for their tremendous knowledge and passion in the oil & gas industry.; and Frank Miller and Steve Addleman for providing a pilot scale version of their proprietary process to facilitate the pilot testing.

  12. Don't Cry over Spilled Water: Identifying Risks and Solutions for Produced Water Spills

    Science.gov (United States)

    Shores, Amanda Rose

    Resource requirements and future energy generation requires careful evaluation, particularly due to climate change and water scarcity. This thesis discusses one aspect of energy generation linked to water; oil-and-gas extraction and the large volumes of waste water produced, otherwise known as "produced water". This research focuses on surface spills of produced water, their ramifications, safeguards against groundwater contamination at spill sites and potential remediation strategies. Produced water contains a variety of contaminants that include the group of known toxins, BTEX (benzene, toluene, ethylbenzene and xylene), and high salt concentrations. A combination of factors such as large volumes of generated produced water, the need for storage and transportation across large distances and the toxic-and-mobile nature of produced water constituents creates risks for spills that can pollute groundwater. Spills occur regularly, particularly in Weld County, Colorado, where the demand for natural gas is high. To answer spill-related hypotheses, a multitude of methodology were employed: modeling, greenhouse experimentation, gas chromatography and summarization of spill reports and statistical analyses. Using publically available spill data, this research found that the frequency of oil-and-gas related spills and the average spilled volume has increased in Weld County from 2011-2015. Additionally, the number of spills that have resulted in groundwater contamination has increased in the area. By focusing on the oil-and-gas operators responsible for these spills, a linear relationship was found between the volumes of oil-and-gas produced compared to the volumes of produced-water generated. However, larger oil-and-gas producers did not show a linear relationship between oil-and-gas produced and produced-water generated, such that larger producers were more efficient and generated less water per unit of energy. So while scale-up efficiency seems to exist for produced-water

  13. Lactic acid bacteria and yeasts associated with spontaneous fermentations during the production of sour cassava starch in Brazil.

    Science.gov (United States)

    Lacerda, Inayara C A; Miranda, Rose L; Borelli, Beatriz M; Nunes, Alvaro C; Nardi, Regina M D; Lachance, Marc-André; Rosa, Carlos A

    2005-11-25

    Sour cassava starch is a traditional fermented food used in the preparation of fried foods and baked goods such as traditional cheese breads in Brazil. Thirty samples of sour cassava starch were collected from two factories in the state of Minas Gerais. The samples were examined for the presence of lactic acid bacteria, yeasts, mesophilic microorganisms, Bacillus cereus and faecal coliforms. Lactic acid bacteria and yeasts isolates were identified by biochemical tests, and the identities were confirmed by molecular methods. Lactobacillus plantarum and Lactobacillus fermentum were the prevalent lactic acid bacteria in product from both factories, at numbers between 6.0 and 9.0 log cfu g(-)(1). Lactobacillus perolans and Lactobacillus brevis were minor fractions of the population. Galactomyces geothricum and Issatchenkia sp. were the prevalent yeasts at numbers of 5.0 log cfu g(-)(1). A species similar to Candida ethanolica was frequently isolated from one factory. Mesophilic bacteria and amylolytic microorganisms were recovered in high numbers at all stages of the fermentation. B. cereus was found at low numbers in product at both factories. The spontaneous fermentations associated with the production of sour cassava starch involve a few species of lactic acid bacteria at high numbers and a variety of yeasts at relatively low numbers.

  14. From Waste to Wealth: Using Produced Water for Agriculture in Colorado

    Science.gov (United States)

    Dolan, F.; Hogue, T. S.

    2017-12-01

    According to estimates from the Colorado Water Plan, the state's population may double by 2050. Due to increasing demand, as much as 0.8 million irrigated acres may dry up statewide from agricultural to municipal and industrial transfers. To help mitigate this loss, new sources of water are being explored in Colorado. One such source may be produced water. Oil and gas production in 2016 alone produced over 300 million barrels of produced water. Currently, the most common method of disposal of produced water is deep well injection, which is costly and has been shown to cause induced seismicity. Treating this water to agricultural standards eliminates the need to dispose of this water and provides a new source of water. This research explores which counties in Colorado may be best suited to reusing produced water for agriculture based on a combined index of need, quality of produced water, and quantity of produced water. The volumetric impact of using produced water for agricultural needs is determined for the top six counties. Irrigation demand is obtained using evapotranspiration estimates from a range of methods, including remote sensing products and ground-based observations. The economic feasibility of treating produced water to irrigation standards is also determined using treatment costs found in the literature and disposal costs in each county. Finally, data from the IHS database is used to obtain the ratio between hydraulic fracturing fluid volumes and produced water volumes in each county. The results of this research will aid in the transition between viewing produced water as a waste product and using it as a tool to help secure water for the arid West.

  15. Domino effect of pollution from sour gas fields : failing legume nodulation and the honey industry

    International Nuclear Information System (INIS)

    Pirker, H.J.

    1998-01-01

    The sustainability of the honey industry in Alberta's Peace Country has been threatened by pollution from sour gas fields. The region has suffered crop reductions and chlorosis in grains, grasses, and legumes. Severe die-back and die-off of aspens and poplars has also been observed. Crops per colony were reduced by as much as 75 per cent, and winter losses more than tripled. Nectar flow patterns shifted from main flow in early summer to late flows in August or September from second growth alfalfa. A sampling of 27 fields found nitrogen fixation in alfalfa and red clovers lacking in areas downwind from major oil and sour gas flaring facilities. The reduction of the early season nectar flow appears to be caused by the synergistic interaction of ozone and sulphur compounds when ozone levels are at their highest. Reduced ozone levels in the fall permit a late, but uncertain flow from alfalfa plants

  16. Domino effect of pollution from sour gas fields : failing legume nodulation and the honey industry

    Energy Technology Data Exchange (ETDEWEB)

    Pirker, H.J. [Peace Country Agricultural Protection Association, AB (Canada)

    1998-10-01

    The sustainability of the honey industry in Alberta`s Peace Country has been threatened by pollution from sour gas fields. The region has suffered crop reductions and chlorosis in grains, grasses, and legumes. Severe die-back and die-off of aspens and poplars has also been observed. Crops per colony were reduced by as much as 75 per cent, and winter losses more than tripled. Nectar flow patterns shifted from main flow in early summer to late flows in August or September from second growth alfalfa. A sampling of 27 fields found nitrogen fixation in alfalfa and red clovers lacking in areas downwind from major oil and sour gas flaring facilities. The reduction of the early season nectar flow appears to be caused by the synergistic interaction of ozone and sulphur compounds when ozone levels are at their highest. Reduced ozone levels in the fall permit a late, but uncertain flow from alfalfa plants.

  17. Hyper-saline produced water treatment for beneficial use

    NARCIS (Netherlands)

    Al-Furaiji, Mustafa

    2016-01-01

    Producing oil and gas is always accompanied with large amounts of effluent water, called “produced water” (PW). These huge quantities of water can be used (if treated efficiently and economically) for many useful purposes like industrial applications, irrigation, cattle and animal consumption, and

  18. NM WAIDS: A PRODUCED WATER QUALITY AND INFRASTRUCTURE GIS DATABASE FOR NEW MEXICO OIL PRODUCERS

    Energy Technology Data Exchange (ETDEWEB)

    Martha Cather; Robert Lee; Ibrahim Gundiler; Andrew Sung; Naomi Davidson; Ajeet Kumar Reddy; Mingzhen Wei

    2003-04-01

    The New Mexico Water and Infrastructure Data System (NM WAIDS) seeks to alleviate a number of produced water-related issues in southeast New Mexico. The project calls for the design and implementation of a Geographical Information System (GIS) and integral tools that will provide operators and regulators with necessary data and useful information to help them make management and regulatory decisions. The major components of this system are: (1) databases on produced water quality, cultural and groundwater data, oil pipeline and infrastructure data, and corrosion information, (2) a web site capable of displaying produced water and infrastructure data in a GIS or accessing some of the data by text-based queries, (3) a fuzzy logic-based, site risk assessment tool that can be used to assess the seriousness of a spill of produced water, and (4) a corrosion management toolkit that will provide operators with data and information on produced waters that will aid them in deciding how to address corrosion issues. The various parts of NM WAIDS will be integrated into a website with a user-friendly interface that will provide access to previously difficult-to-obtain data and information. Primary attention during the first six months of this project has been focused on creating the water quality databases for produced water and surface water, along with collection of corrosion information and building parts of the corrosion toolkit. Work on the project to date includes: (1) Creation of a water quality database for produced water analyses. The database was compiled from a variety of sources and currently has over 4000 entries for southeast New Mexico. (2) Creation of a web-based data entry system for the water quality database. This system allows a user to view, enter, or edit data from a web page rather than having to directly access the database. (3) Creation of a semi-automated data capturing system for use with standard water quality analysis forms. This system improves the

  19. NM WAIDS: A PRODUCED WATER QUALITY AND INFRASTRUCTURE GIS DATABASE FOR NEW MEXICO OIL PRODUCERS

    Energy Technology Data Exchange (ETDEWEB)

    Martha Cather; Robert Lee; Ibrahim Gundiler; Andrew Sung

    2003-09-24

    The New Mexico Water and Infrastructure Data System (NM WAIDS) seeks to alleviate a number of produced water-related issues in southeast New Mexico. The project calls for the design and implementation of a Geographical Information System (GIS) and integral tools that will provide operators and regulators with necessary data and useful information to help them make management and regulatory decisions. The major components of this system are: (1) Databases on produced water quality, cultural and groundwater data, oil pipeline and infrastructure data, and corrosion information. (2) A web site capable of displaying produced water and infrastructure data in a GIS or accessing some of the data by text-based queries. (3) A fuzzy logic-based, site risk assessment tool that can be used to assess the seriousness of a spill of produced water. (4) A corrosion management toolkit that will provide operators with data and information on produced waters that will aid them in deciding how to address corrosion issues. The various parts of NM WAIDS will be integrated into a website with a user-friendly interface that will provide access to previously difficult-to-obtain data and information. Primary attention during the first six months of this project was focused on creating the water quality databases for produced water and surface water, along with collecting of corrosion information and building parts of the corrosion toolkit. Work on the project to date includes: (1) Creation of a water quality database for produced water analyses. The database was compiled from a variety of sources and currently has over 7000 entries for New Mexico. (2) Creation of a web-based data entry system for the water quality database. This system allows a user to view, enter, or edit data from a web page rather than having to directly access the database. (3) Creation of a semi-automated data capturing system for use with standard water quality analysis forms. This system improves the accuracy and speed

  20. Inhibitory effect of cyanide on wastewater nitrification determined using SOUR and RNA-based gene-specific assays

    Science.gov (United States)

    The effect of CN- (CN-) on nitrification was examined with samples from nitrifying wastewater enrichments using two different approaches: by measuring substrate (ammonia) specific oxygen uptake rates (SOUR), and by using RT-qPCR to quantify the transcripts of functional genes inv...

  1. Changes in sour cherry (Prunus cerasus L.) antioxidants during nectar processing and in vitro gastrointestinal digestion.

    NARCIS (Netherlands)

    Toydemir, G.; Capanoglu, E.; Kamiloglu, S.; Boyacioglu, D.; Vos, de C.H.; Hall, R.D.; Beekwilder, M.J.

    2013-01-01

    Sour cherry (Prunus cerasus L.) is rich in polyphenols, and like its processed products, is especially rich in anthocyanins. We have applied HPLC, spectrophotometric and on-line antioxidant detection methods to follow the fate of cherry antioxidants during an entire multi-step industrial-scale

  2. Membrane Technology for Produced Water in Lea County

    Energy Technology Data Exchange (ETDEWEB)

    Cecilia Nelson; Ashok Ghosh

    2011-06-30

    Southeastern New Mexico (SENM) is rich in mineral resources, including oil and gas. Produced water is a byproduct from oil and gas recovery operations. SENM generates approximately 400 million barrels per year of produced water with total dissolved solids (TDS) as high as ~ 200,000 ppm. Typically, produced water is disposed of by transporting it to injection wells or disposal ponds, costing around $1.2 billion per year with an estimated use of 0.3 million barrels of transportation fuel. New Mexico ranks first among U.S. states in potash production. Nationally, more than 85% of all potash produced comes from the Carlsbad potash district in SENM. Potash manufacturing processes use large quantities of water, including fresh water, for solution mining. If the produced water from oilfield operations can be treated and used economically in the potash industry, it will provide a beneficial use for the produced water as well as preserve valuable water resources in an area where fresh water is scarce. The goal of this current research was to develop a prototype desalination system that economically treats produced water from oil and/or natural gas operations for the beneficial use of industries located in southeastern New Mexico. Up until now, most water cleaning technologies have been developed for treating water with much lower quantities of TDS. Seawater with TDS of around 30,000 ppm is the highest concentration that has been seriously studied by researchers. Reverse osmosis (RO) technology is widely used; however the cost remains high due to high-energy consumption. Higher water fluxes and recoveries are possible with a properly designed Forward Osmosis (FO) process as large driving forces can be induced with properly chosen membranes and draw solution. Membrane fouling and breakdown is a frequent and costly problem that drives the cost of desalination very high. The technology developed by New Mexico Tech (NMT) researchers not only protects the membrane, but has also

  3. Beneficial Reuse of Produced and Flowback Water

    Science.gov (United States)

    Water reuse and recycling is a significant issue in the development of oil and gas shale plays in the United StatesDrilling operations – 60,000 to 650,000 gallons per wellHydraulic fracturing operations – 3 million to 5 million gallons per wellDefinition of produced water and flowback waterInteractions of water quality constituents as they relate to water reuse and recyclingTesting criteria in the laboratory and field operations

  4. An economically viable alternative to coastal discharge of produced water

    International Nuclear Information System (INIS)

    D'Unger, C.V.; Carr, R.S.; Chapman, D.C.

    1993-01-01

    The discharge of produced waters to coastal estuaries has been common practice on the Texas coast for many years as these discharges are currently exempt from NPDES permitting. A study of the active produced water discharges in Nueces Bay, Texas revealed that all eight effluents were highly toxic as determined by the sea urchin (Arbacia punctulata) fertilization and embryological development assays. An alternative to discharging produced water into coastal estuaries is the use of disposal wells. Inactive wells can be converted to produced water disposal wells. Production records for the Nueces Bay, Texas area reveal that 52% of the gas wells produce less than 100 mcf/d and 50% of the oil wells produce less than 10 b/d. Using conservative estimates, the cost of converting an inactive well to a disposal well was calculated to be $31,500 which could be paid out by a gas well producing as little as 100 mcf/d in 26 months using only 50% of the well's profit. Combining multiple leases to a single disposal well would reduce proportionately the cost to each operation. This study has demonstrated that economically viable disposal options could be achieved in the Nueces Bay area through the imaginative and cooperative formation of produced water disposal ventures. This same model could be applied to produced water discharges in other coastal areas

  5. Produced water: Market and global trends - oil production - water production - choice of technology

    International Nuclear Information System (INIS)

    Robertson, Steve

    2006-01-01

    The presentation discusses various aspects of the world oil production, the energy demand, the future oil supply, the oil prices and the production growth. Some problems with produced water are also discussed as well as aspects of the market for produced water technology (tk)

  6. A Review on overboard CEOR discharged produced water treatment and remediation

    Science.gov (United States)

    Rawindran, H.; Krishnan, S.; Sinnathambi, C. M.

    2017-06-01

    Produced water is a waste by-product generated during oil and gas recovery operations. It contains the mixture of organic and inorganic compounds. Produced water management is a challenge faced by the petroleum practitioners worldwide. Build-up of chemical wastes from produced water causes huge footprint, which results in high CapEx and OpEx. Different technologies are practiced by various practitioners to treat the produced waste water. However, the constituents removed by each technology and the degree of organic compound removal has to be considered to identify the potential and effective treatment technologies for offshore industrial applications. Current produced water technologies and their successful applications have advantages and disadvantages and can be ranked on the basis of several factors, such as their discharge limit into water bodies, reinjection in producing well, or for any miscellaneous beneficial use. This paper attempts to provide a review of existing physical and chemical treatment technologies used for management of produced water. Based on our analysis, suitable methods will be recommended for offshore waste water treatment technologies.

  7. Cross-Linkable Polyimide Membranes for Improved Plasticization Resistance and Permselectivity in Sour Gas Separations

    KAUST Repository

    Kraftschik, Brian

    2013-09-10

    A series of cross-linkable membrane materials based on the 6FDA-DAM:DABA (3:2) polyimide backbone were synthesized for improved sour gas separation performance, in terms of both membrane stability and permselectivity. Short-chain poly(ethylene glycol) (PEG) molecules were used as cross-linking agents in an esterification-based cross-linking reaction. Pure and mixed gas permeation and pure gas sorption experiments were performed on dense films of these materials. Compared to unmodified 6FDA-DAM:DABA (3:2), higher sour gas permselectivity and membrane stability were achieved under aggressive feed conditions. H2S-induced plasticization was not evident until pure H2S feed pressures greater than approximately 6-8 bar. Pure CO 2-induced plasticization only occurred at feed pressures greater than about 25 bar. Under mixed gas feed conditions with 20% H2S, 20% CO2, and 60% CH4 at 35 C, attractive selectivities above 22 and 27 for H2S/CH4 and CO2/CH4, respectively, were observed for a feed pressure of 62 bar with both triethylene glycol and tetraethylene glycol cross-linking agents. © 2013 American Chemical Society.

  8. Cross-Linkable Polyimide Membranes for Improved Plasticization Resistance and Permselectivity in Sour Gas Separations

    KAUST Repository

    Kraftschik, Brian; Koros, William J.

    2013-01-01

    A series of cross-linkable membrane materials based on the 6FDA-DAM:DABA (3:2) polyimide backbone were synthesized for improved sour gas separation performance, in terms of both membrane stability and permselectivity. Short-chain poly(ethylene glycol) (PEG) molecules were used as cross-linking agents in an esterification-based cross-linking reaction. Pure and mixed gas permeation and pure gas sorption experiments were performed on dense films of these materials. Compared to unmodified 6FDA-DAM:DABA (3:2), higher sour gas permselectivity and membrane stability were achieved under aggressive feed conditions. H2S-induced plasticization was not evident until pure H2S feed pressures greater than approximately 6-8 bar. Pure CO 2-induced plasticization only occurred at feed pressures greater than about 25 bar. Under mixed gas feed conditions with 20% H2S, 20% CO2, and 60% CH4 at 35 C, attractive selectivities above 22 and 27 for H2S/CH4 and CO2/CH4, respectively, were observed for a feed pressure of 62 bar with both triethylene glycol and tetraethylene glycol cross-linking agents. © 2013 American Chemical Society.

  9. Application of natural antimicrobial compounds for reservoir souring and MIC prevention in offshore oil and gas production systems

    DEFF Research Database (Denmark)

    Thomsen, Mette Hedegaard; Skovhus, Torben Lund; Mashietti, Marco

    Offshore oil production facilities are subjectable to internal corrosion, potentially leading to human and environmental risk and significant economic losses. Microbiologically influenced corrosion (MIC) and reservoir souring - sulphide production by sulfate reducing microorganisms in the reservo...

  10. Formation and Control of Sulfur Oxides in Sour Gas Oxy-Combustion: Prediction Using a Reactor Network Model

    KAUST Repository

    Bongartz, Dominik; Shanbhogue, Santosh J.; Ghoniem, Ahmed F.

    2015-01-01

    © 2015 American Chemical Society. Sour natural gas currently requires expensive gas cleanup before it can be used in power generation because it contains large amounts of hydrogen sulfide (H2S) and carbon dioxide (CO2) that entail a low heating

  11. Control of microbially generated hydrogen sulfide in produced waters

    Energy Technology Data Exchange (ETDEWEB)

    Burger, E.D.; Vance, I.; Gammack, G.F.; Duncan, S.E.

    1995-12-31

    Production of hydrogen sulfide in produced waters due to the activity of sulfate-reducing bacteria (SRB) is a potentially serious problem. The hydrogen sulfide is not only a safety and environmental concern, it also contributes to corrosion, solids formation, a reduction in produced oil and gas values, and limitations on water discharge. Waters produced from seawater-flooded reservoirs typically contain all of the nutrients required to support SRB metabolism. Surface processing facilities provide a favorable environment in which SRB flourish, converting water-borne nutrients into biomass and H{sub 2}S. This paper will present results from a field trial in which a new technology for the biochemical control of SRB metabolism was successfully applied. A slip stream of water downstream of separators on a produced water handling facility was routed through a bioreactor in a side-steam device where microbial growth was allowed to develop fully. This slip stream was then treated with slug doses of two forms of a proprietary, nonbiocidal metabolic modifier. Results indicated that H{sub 2}S production was halted almost immediately and that the residual effect of the treatment lasted for well over one week.

  12. Innovative Water Management Technology to Reduce Environment Impacts of Produced Water

    Energy Technology Data Exchange (ETDEWEB)

    Castle, James; Rodgers, John; Alley, Bethany; Coffey, Ruthanne; Jurinko, Kristen; Pardue, Michael; Ritter, Tina; Spacil, Michael

    2013-05-15

    Clemson University with Chevron as an industry partner developed and applied treatment technology using constructed wetland systems to decrease targeted constituents in simulated and actual produced waters to achieve reuse criteria and discharge limits. Pilot-scale and demonstration constructed wetland treatment system (CWTS) experiments led to design strategies for treating a variety of constituents of concern (COCs) in produced waters including divalent metals, metalloids, oil and grease, and ammonia. Targeted biogeochemical pathways for treatment of COCs in pilot-scale CWTS experiments included divalent metal sulfide precipitation through dissimilatory sulfate reduction, metal precipitation through oxidation, reduction of selenite to insoluble elemental selenium, aerobic biodegradation of oil, nitrification of ammonia to nitrate, denitrification of nitrate to nitrogen gas, separation of oil using an oilwater separator, and sorption of ammonia to zeolite. Treatment performance results indicated that CWTSs can be designed and built to promote specific environmental and geochemical conditions in order for targeted biogeochemical pathways to operate. The demonstration system successfully achieved consistent removal extents even while inflow concentrations of COCs in the produced water differed by orders of magnitude. Design strategies used in the pilot-scale and demonstration CWTSs to promote specific conditions that can be applied to designing full-scale CWTSs include plant and soil selection, water-depth selection, addition of amendments, and hydraulic retention time (HRT). These strategies allow conditions within a CWTS to be modified to achieve ranges necessary for the preferred biogeochemical treatment pathways. In the case of renovating a produced water containing COCs that require different biogeochemical pathways for treatment, a CWTS can be designed with sequential cells that promote different conditions. For example, the pilot-scale CWTS for post

  13. Innovative Water Management Technology to Reduce Environmental Impacts of Produced Water

    Energy Technology Data Exchange (ETDEWEB)

    Castle, James; Rodgers, John; Alley, Bethany; Beebe, Alex; Coffey, Ruthanne; Jurinko, Kristen; Pardue, Michael; Ritter, Tina; Spacil, Michael

    2013-05-15

    Clemson University with Chevron as an industry partner developed and applied treatment technology using constructed wetland systems to decrease targeted constituents in simulated and actual produced waters to achieve reuse criteria and discharge limits. Pilot-scale and demonstration constructed wetland treatment system (CWTS) experiments led to design strategies for treating a variety of constituents of concern (COCs) in produced waters including divalent metals, metalloids, oil and grease, and ammonia. Targeted biogeochemical pathways for treatment of COCs in pilot-scale CWTS experiments included divalent metal sulfide precipitation through dissimilatory sulfate reduction, metal precipitation through oxidation, reduction of selenite to insoluble elemental selenium, aerobic biodegradation of oil, nitrification of ammonia to nitrate, denitrification of nitrate to nitrogen gas, separation of oil using an oilwater separator, and sorption of ammonia to zeolite. Treatment performance results indicated that CWTSs can be designed and built to promote specific environmental and geochemical conditions in order for targeted biogeochemical pathways to operate. The demonstration system successfully achieved consistent removal extents even while inflow concentrations of COCs in the produced water differed by orders of magnitude. Design strategies used in the pilot-scale and demonstration CWTSs to promote specific conditions that can be applied to designing full-scale CWTSs include plant and soil selection, water-depth selection, addition of amendments, and hydraulic retention time (HRT). These strategies allow conditions within a CWTS to be modified to achieve ranges necessary for the preferred biogeochemical treatment pathways. In the case of renovating a produced water containing COCs that require different biogeochemical pathways for treatment, a CWTS can be designed with sequential cells that promote different conditions. For example, the pilot-scale CWTS for post

  14. Innovative Water Management Technology to Reduce Environment Impacts of Produced Water

    Energy Technology Data Exchange (ETDEWEB)

    Castle, James W. [Clemson Univ., SC (United States); Rodgers, John H. [Clemson Univ., SC (United States); Alley, Bethany [Clemson Univ., SC (United States); Beebe, Alex [Clemson Univ., SC (United States); Coffey, Ruthanne [Clemson Univ., SC (United States); Jurinko, Kristen [Clemson Univ., SC (United States); Pardue, Michael [Clemson Univ., SC (United States); Ritter, Tina [Clemson Univ., SC (United States); Spacil, Michael M. [Clemson Univ., SC (United States)

    2013-08-08

    Clemson University with Chevron as an industry partner developed and applied treatment technology using constructed wetland systems to decrease targeted constituents in simulated and actual produced waters to achieve reuse criteria and discharge limits. Pilot-scale and demonstration constructed wetland treatment system (CWTS) experiments led to design strategies for treating a variety of constituents of concern (COCs) in produced waters including divalent metals, metalloids, oil and grease, and ammonia. Targeted biogeochemical pathways for treatment of COCs in pilot-scale CWTS experiments included divalent metal sulfide precipitation through dissimilatory sulfate reduction, metal precipitation through oxidation, reduction of selenite to insoluble elemental selenium, aerobic biodegradation of oil, nitrification of ammonia to nitrate, denitrification of nitrate to nitrogen gas, separation of oil using an oilwater separator, and sorption of ammonia to zeolite. Treatment performance results indicated that CWTSs can be designed and built to promote specific environmental and geochemical conditions in order for targeted biogeochemical pathways to operate. The demonstration system successfully achieved consistent removal extents even while inflow concentrations of COCs in the produced water differed by orders of magnitude. Design strategies used in the pilot-scale and demonstration CWTSs to promote specific conditions that can be applied to designing full-scale CWTSs include plant and soil selection, water-depth selection, addition of amendments, and hydraulic retention time (HRT). These strategies allow conditions within a CWTS to be modified to achieve ranges necessary for the preferred biogeochemical treatment pathways. In the case of renovating a produced water containing COCs that require different biogeochemical pathways for treatment, a CWTS can be designed with sequential cells that promote different conditions. For example, the pilot-scale CWTS for post

  15. POLICY ANALYSIS OF PRODUCED WATER ISSUES ASSOCIATED WITH IN-SITU THERMAL TECHNOLOGIES

    Energy Technology Data Exchange (ETDEWEB)

    Robert Keiter; John Ruple; Heather Tanana

    2011-02-01

    Commercial scale oil shale and oil sands development will require water, the amount of which will depend on the technologies adopted and the scale of development that occurs. Water in oil shale and oil sands country is already in scarce supply, and because of the arid nature of the region and limitations on water consumption imposed by interstate compacts and the Endangered Species Act, the State of Utah normally does not issue new water rights in oil shale or oil sands rich areas. Prospective oil shale and oil sands developers that do not already hold adequate water rights can acquire water rights from willing sellers, but large and secure water supplies may be difficult and expensive to acquire, driving oil shale and oil sands developers to seek alternative sources of supply. Produced water is one such potential source of supply. When oil and gas are developed, operators often encounter ground water that must be removed and disposed of to facilitate hydrocarbon extraction. Water produced through mineral extraction was traditionally poor in quality and treated as a waste product rather than a valuable resource. However, the increase in produced water volume and the often-higher quality water associated with coalbed methane development have drawn attention to potential uses of produced water and its treatment under appropriations law. This growing interest in produced water has led to litigation and statutory changes that must be understood and evaluated if produced water is to be harnessed in the oil shale and oil sands development process. Conversely, if water is generated as a byproduct of oil shale and oil sands production, consideration must be given to how this water will be disposed of or utilized in the shale oil production process. This report explores the role produced water could play in commercial oil shale and oil sands production, explaining the evolving regulatory framework associated with produced water, Utah water law and produced water regulation

  16. New progress in wastewater treatment technology for standard-reaching discharge in sour gas fields

    Directory of Open Access Journals (Sweden)

    Jie Yang

    2018-02-01

    Full Text Available Gas field water is generally characterized by complex contaminant components and high salinity. Its proper treatment has always been the great concern in the field of environmental protection of oil & gas fields. In this paper, the wastewater from a gas field in the Sichuan Basin with high salinity and more contaminants (e.g. sulfides was treated as a case study for the standard-reaching discharge. Lab experiments were carried out to analyze the adaptability and effectiveness of coagulation–desulfurization composite treatment technology, chemical oxidation based ammonia nitrogen removal technology and cryogenic multi-efficacy distillation technology in the treatment of wastewater in this field. The results show that the removal rate of sulfides and oils is over 90% if polymeric ferric sulfate (PFS is taken as the coagulant combined with TS-1 desulfurization agent. Besides, the removal rate of ammonia nitrogen is over 96% if CA-1 is taken as the oxidant. Finally, after the gas field water is treated by means of cryogenic three-efficacy distillation technology, chloride concentration of distilled water is below 150 mg/L and CODcr concentration is less than 60 mg/L. It is concluded that after the whole process treatment, the main contaminant indicators of wastewater in this case study can satisfy the grade one standard specified in the Integrated Wastewater Discharge Standard (GB 8978–1996 and the chloride concentration can meet the requirement of the Standards for Irrigation Water Quality (GB 5084–2005. To sum up, the above mentioned composite technologies are efficient to the wastewater treatment in sour gas fields. Keywords: Sulfide-bearing gas field water, Coagulation, Desulfurization, Chemical oxidation, Standard discharge, Ammonia nitrogen, Chloride, Cryogenic multi-efficacy distillation, Sichuan Basin

  17. HPLC and MS/MS study of polar contaminants in a wetland adjoining a sour-gas plant

    International Nuclear Information System (INIS)

    Dickson, L.C.; Headley, J.V.; Peru, K.; Spiegel, K.; Gandrass, J.

    1995-01-01

    An analytical methodology was developed for target analyses and broad spectrum characterization of polar contaminants such as nitrogenous and organosulfur compounds in wetlands using the complementary techniques of HPLC with electrochemical (EC) detection and tandem MS with probe and electrospray ionization. Tandem MS was well suited for the identification and quantification of mixtures of polar compounds in water samples and soil extracts, while HPLC-EC provided sensitive detection of compounds transparent to MS detection and conventional methods. The usefulness of the methodology is demonstrated by studying the removal of polar contaminants from a wetland in western Canada affected by releases of hydrocarbon-rich condensate and free product from an adjoining sour-gas plant. The concern is that the mobile water-soluble polar contaminants may not be as efficiently attenuated by volatilization or adsorption processes as the more hydrophobic hydrocarbons and that some of the polar toxic compounds may break through to contaminate groundwater and surface waters. Samples of groundwater, surface water, and aqueous soil extracts were analyzed to quantify levels of polar contaminants in the presence of high concentrations of hydrocarbons. The use of water extracts reduced the background interference from hydrocarbons and other non-polar compounds that were present in the soil samples. HPLC-EC was used to quantify the target compounds that included monoethanolamine, diethanolamine and methyldiethanolamine and sulfolane-derived compounds while tandem MS was used to identify related compounds and degradation products. Influent concentrations were in the ppm range and discharge concentrations were in the ppb range

  18. Monitoring Environmental Recovery at Terminated Produced Water Discharge Sites in Coastal Louisiana Waters

    Energy Technology Data Exchange (ETDEWEB)

    Continental Shelf Associates, Inc.

    1999-08-16

    This report presents the results of a study of terminated produced water discharge sites in the coastal waters of Louisiana. Environmental recovery at the sites is documented by comparing pre-termination and post-termination (six months and one year) data. Produced water, sediments, and sediment interstitial water samples were analyzed for radionuclides, metals, and hydrocarbons. Benthic infauna were identified from samples collected in the vicinity of the discharge and reference sites. Radium isotope activities were determined in fish and crustacean samples. In addition, an environmental risk assessment is made on the basis of the concentrations of metals and hydrocarbons determined in the samples.

  19. Effectiveness of managed populations of wild and honey bees as supplemental pollinators of sour cherry (Prunus cerasus L.) under different climatic conditions

    DEFF Research Database (Denmark)

    Hansted, Lise; Grout, Brian William Wilson; Toldam-Andersen, Torben Bo

    2015-01-01

    Managed populations of Apis mellifera, Bombus terrestris and Osmia have been investigated rufa as sour cherry pollinators in two flowering seasons with different weather patterns. Flight activity of the three bee species during the pollination-receptive period of the cultivar ‘Stevnsbaer’ was rec......Managed populations of Apis mellifera, Bombus terrestris and Osmia have been investigated rufa as sour cherry pollinators in two flowering seasons with different weather patterns. Flight activity of the three bee species during the pollination-receptive period of the cultivar ‘Stevnsbaer...

  20. Comparative experiments on polymer degradation technique of produced water of polymer flooding oilfield

    Science.gov (United States)

    Chen, Rong; Qi, Mei; Zhang, Guohui; Yi, Chenggao

    2018-02-01

    The application of polymer flooding technology in oilfields can result in polymer content increased in produced water. This increasing made produced water quality become poor. The efficiency of produced water processing decreased significantly. Processed water quality seriously exceeded criterion’s stipulation. The presence of the polymer in produced water is the main reason for more difficulties in processing of produced water, therefore the polymer degradation technology is a key coefficient in produced water processing for polymer flooding oilfields. We evaluated several physical and chemical polymer degradation methods with the solution of separated water from polymer flooding oilfields and hydrolyzed polyacrylamide. The experiment results can provide a basis for produced water processing technologies application in polymer flooding oilfields.

  1. Fruit Set of Several Sour Cherry Cultivars in Latvia Influenced by Weather Conditions Before and During Flowering

    Directory of Open Access Journals (Sweden)

    Feldmane Daina

    2017-06-01

    Full Text Available Fruit set is a crucial stage in the process of yield formation, which is influenced by environmental factors, growing technologies and peculiarities of genotype. The aim of the study was to evaluate the quality of pollen (viability and germination capacity and the effect of weather before and during flowering on fruit set in sour cherry cultivars ‘Latvijas Zemais’, ‘Zentenes’, ‘Bulatnikovskaya’, and ‘Orlica’. The research was carried out in Institute of Horticulture (Latvia University of Agriculture in 2009-2016. Good pollen viability and germination was found for cultivars ‘Latvijas Zemais’ and ‘Bulatnikovskaya’. Negative effects of increasing air temperature (in the range of 7.7 to 17.5 °C and relative humidity (in the range of 51.4 to 88.5% was observed for all cultivars during flowering. The effects of diurnal temperature fluctuations, wind and the amount of days with precipitation differed depending on sour cherry cultivar.

  2. Physico-chemical analyses and corrosion effect of produced water ...

    African Journals Online (AJOL)

    Physico-chemical characteristics of the composite produced water sample used for the study has a higher concentration compared with DPR standard for discharge of produced formation water into surface environment. It was assumed that the corrosion of the coupons was due to presence of high chemical matters in the ...

  3. Assessment of produced water contaminated soils to determine remediation requirements

    International Nuclear Information System (INIS)

    Clodfelter, C.

    1995-01-01

    Produced water and drilling fluids can impact the agricultural properties of soil and result in potential regulatory and legal liabilities. Produced water typically is classified as saline or a brine and affects surface soils by increasing the sodium and chloride content. Sources of produced water which can lead to problems include spills from flowlines and tank batteries, permitted surface water discharges and pit areas, particularly the larger pits including reserve pits, emergency pits and saltwater disposal pits. Methods to assess produced water spills include soil sampling with various chemical analyses and surface geophysical methods. A variety of laboratory analytical methods are available for soil assessment which include electrical conductivity, sodium adsorption ratio, cation exchange capacity, exchangeable sodium percent and others. Limiting the list of analytical parameters to reduce cost and still obtain the data necessary to assess the extent of contamination and determine remediation requirements can be difficult. The advantage to using analytical techniques is that often regulatory remediation standards are tied to soil properties determined from laboratory analysis. Surface geophysical techniques can be an inexpensive method to rapidly determine the extent and relative magnitude of saline soils. Data interpretations can also provide an indication of the horizontal as well as the vertical extent of impacted soils. The following discussion focuses on produced water spills on soil and assessment of the impacted soil. Produced water typically contains dissolved hydrocarbons which are not addressed in this discussion

  4. Produced water reuse aiming reinjection; Reuso de agua produzida visando reinjecao

    Energy Technology Data Exchange (ETDEWEB)

    Louvisse, Ana Maria Travalloni; Hora, Jairo Maynard da Fonseca; Guilherme, Claudio [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2004-07-01

    As an oil reservoir goes aging, the BSW (water and solid content associated to the crude oil ) from the produced oil increase acutely. As this associated water is isolated from the crude oil, it presents several contaminants with concentrations above to that specified in the environmental norms for its discharge. Attending the environmental legislation, some times, is very difficult and can even enable the entire project. As the reservoir becomes old, enhance techniques are necessary to maintain the oil producing. A common recovery mechanism, called secondary recovery, is the water injection. Commonly the water for secondary recovery is not easily available. The main objective of this work is present a treatment system for produced water used in a specific field in the Northwest region. This treatment involves reinjection of this water after filtration. We will have a high environmental benefited, avoiding the discharge of produced water, highly toxic, and at the same time enhanced the oil production. In this work, we develop a method to modify the physical chemistry characteristics of the produced water and increase the treatment process efficiency. (author)

  5. Lithium recovery from shale gas produced water using solvent extraction

    International Nuclear Information System (INIS)

    Jang, Eunyoung; Jang, Yunjai; Chung, Eunhyea

    2017-01-01

    Shale gas produced water is hypersaline wastewater generated after hydraulic fracturing. Since the produced water is a mixture of shale formation water and fracturing fluid, it contains various organic and inorganic components, including lithium, a useful resource for such industries as automobile and electronics. The produced water in the Marcellus shale area contains about 95 mg/L lithium on average. This study suggests a two-stage solvent extraction technique for lithium recovery from shale gas produced water, and determines the extraction mechanism of ions in each stage. All experiments were conducted using synthetic shale gas produced water. In the first-stage, which was designed for the removal of divalent cations, more than 94.4% of Ca"2"+, Mg"2"+, Sr"2"+, and Ba"2"+ ions were removed by using 1.0 M di-(2-ethylhexyl) phosphoric acid (D2EHPA) as an extractant. In the second-stage, for lithium recovery, we could obtain a lithium extraction efficiency of 41.2% by using 1.5 M D2EHPA and 0.3 M tributyl phosphate (TBP). Lithium loss in the first-stage was 25.1%, and therefore, the total amount of lithium recovered at the end of the two-step extraction procedure was 30.8%. Through this study, lithium, one of the useful mineral resources, could be selectively recovered from the shale gas produced water and it would also reduce the wastewater treatment cost during the development of shale gas. - Highlights: • Lithium was extracted from shale gas produced water using an organic solvent. • Two-stage solvent extraction technique was applied. • Divalent cations were removed in the first stage by D2EHPA. • Lithium was selectively recovered in the second stage by using TBP with D2EHPA.

  6. Influence of the date of cut of rootstocks to the stub on growth of maider sour cherry trees cv. 'Łutówka'

    Directory of Open Access Journals (Sweden)

    Stanisław Wociór

    2013-12-01

    Full Text Available Over a three-year period (1997-1999 investigations were conducted on the effect of 6 date of cut to the stub on tree trunk diameter, height and branching of sour cherry maidens in the nursery.On the Prunus mahaleb seedling rootstock were found no significant influen ce of the date between January, 15 - March, 30 of cut to the stub on growth of sour cherry maidens cv. ´Łutówka' (tree trunk diameter and branching and efficiency of nursery. The date of cutting in 15 April decreased trunk diameter and percent of the first quality trees.

  7. OZONE TREATMENT OF SOLUBLE ORGANICS IN PRODUCED WATER

    Energy Technology Data Exchange (ETDEWEB)

    Klasson, KT

    2002-03-14

    This project was an extension of previous research to improve the applicability of ozonation and will help address the petroleum-industry problem of treating produced water containing soluble organics. The goal of this project was to maximize oxidation of hexane-extractable organics during a single-pass operation. The project investigated: (1) oxidant production by electrochemical and sonochemical methods, (2) increasing the mass transfer rate in the reactor by forming microbubbles during ozone injection into the produced water, and (3) using ultraviolet irradiation to enhance the reaction if needed. Several types of methodologies for treatment of soluble organics in synthetic and actual produced waters have been performed. The technologies tested may be categorized as follows: (1) Destruction via sonochemical oxidation at different pH, salt concentration, ultraviolet irradiation, and ferrous iron concentrations. (2) Destruction via ozonation at different pH, salt concentration, hydrogen peroxide concentrations, ultraviolet irradiation, temperature, and reactor configurations.

  8. Emissions from Produced Water Treatment Ponds, Uintah Basin, Utah, USA

    Science.gov (United States)

    Mansfield, M. L.; Lyman, S. N.; Tran, H.; O'Neil, T.; Anderson, R.

    2015-12-01

    An aqueous phase, known as "produced water," usually accompanies the hydrocarbon fluid phases that are extracted from Earth's crust during oil and natural gas extraction. Produced water contains dissolved and suspended organics and other contaminants and hence cannot be discharged directly into the hydrosphere. One common disposal method is to discharge produced water into open-pit evaporation ponds. Spent hydraulic fracturing fluids are also often discharged into the same ponds. It is obvious to anyone with a healthy olfactory system that such ponds emit volatile organics to the atmosphere, but very little work has been done to characterize such emissions. Because oil, gas, and water phases are often in contact in geologic formations, we can expect that more highly soluble compounds (e.g., salts, alcohols, carbonyls, carboxyls, BTEX, etc.) partition preferentially into produced water. However, as the water in the ponds age, many physical, chemical, and biological processes alter the composition of the water, and therefore the composition and strength of volatile organic emissions. For example, some ponds are aerated to hasten evaporation, which also promotes oxidation of organics dissolved in the water. Some ponds are treated with microbes to promote bio-oxidation. In other words, emissions from ponds are expected to be a complex function of the composition of the water as it first enters the pond, and also of the age of the water and of its treatment history. We have conducted many measurements of emissions from produced water ponds in the Uintah Basin of eastern Utah, both by flux chamber and by evacuated canister sampling with inverse modeling. These measurements include fluxes of CO2, CH4, methanol, and many other volatile organic gases. We have also measured chemical compositions and microbial content of water in the ponds. Results of these measurements will be reported.

  9. In Vivo Fast Induction of Homogeneous Autopolyploids via Callus in Sour Jujube (Ziziphus acidojujuba Cheng et Liu

    Directory of Open Access Journals (Sweden)

    Qinghua Shi

    2016-05-01

    Full Text Available Polyploidization has been demonstrated as a very effective approach in fruit tree improvement. Sour jujube (Ziziphus acidojujuba Cheng et Liu is a promising diploid wild, traditional fruit species (2n = 2x = 24 that is rich in vitamin C, which is the main rootstock of Chinese jujube (Z. jujuba Mill.. The novel method we developed for rapid in vivo induction of homogeneous autopolyploids (IVIHA via callus in Chinese jujube was first applied and further optimized in sour jujube. Under optimized conditions, an average of one pure autotetraploid shoot could be regenerated from one treated branch, thereby indicating a relatively high efficiency rate. A total of 9 pure autotetraploid genotypes were created, and one of these was released as a new cultivar named ‘Zhuguang’ in 2015. Moreover, unexpected octoploids and hexaploids were also simultaneously created and detected. The leaves of tetraploids were thicker, broader, and darker in color than those of the original diploids, whereas the leaf sizes of octoploids were much smaller compared to that of diploids. However, stoma size increased with the occurrence of ploidy, mainly from diploid to octoploid. The well grown ploidies of jujube included diploids, triploids, and tetraploids. Anatomical observation indicated that adventitious buds/shoots emerged from the callus that formed on the cut, which was then followed by the development of connective vascular tissues between the adventitious bud and the stock plant tissue. This study demonstrates the universality of the IVIHA method that was initially developed in Chinese jujube, as well as provides a foundation for high-efficiency pure polyploid induction in sour jujube.

  10. Membrane crystallization for recovery of salts from produced water

    DEFF Research Database (Denmark)

    Quist-Jensen, Cejna Anna; Jensen, Henriette Casper; Ali, Aamer

    Membrane Crystallization (MCr) is a novel technology able to recover freshwater and high-purity salts from complex solutions and therefore, is suggested for a better exploitation of wastewater streams. Unlike other membrane processes, MCr is not limited by high concentrations and, therefore, the ......, the membrane maintained its hydrophobic nature despite that produced water contained oil residues. Conductivity and HPLC was utilized to analyze the quality of the permeate stream......., the solutions can be treated to achieve saturation level. Hereby different salts can be precipitated and directly recovered from various streams. In this study, it is shown that MCr is able to treat produced water by producing clean water and simultaneously NaCl crystals. The recovered crystals exhibited high...

  11. Environmental aspects of produced-water salt releases in onshore and coastal petroleum-producing areas of the conterminous U.S. - a bibliography

    Science.gov (United States)

    Otton, James K.

    2006-01-01

    Environmental effects associated with the production of oil and gas have been reported since the first oil wells were drilled in the Appalachian Basin in Pennsylvania and Kentucky in the early to mid-1800s. The most significant of these effects are the degradation of soils, ground water, surface water, and ecosystems they support by releases of suspended and dissolved hydrocarbons and co-produced saline water. Produced water salts are less likely than hydrocarbons to be adsorbed by mineral phases in the soil and sediment and are not subject to degradation by biologic processes. Sodium is a major dissolved constituent in most produced waters and it causes substantial degradation of soils through altering of clays and soil textures and subsequent erosion. Produced water salts seem to have the most wide-ranging effects on soils, water quality, and ecosystems. Trace elements, including boron, lithium, bromine, fluorine, and radium, also occur in elevated concentrations in some produced waters. Many trace elements are phytotoxic and are adsorbed and may remain in soils after the saline water has been flushed away. Radium-bearing scale and sludge found in oilfield equipment and discarded on soils pose additional hazards to human health and ecosystems. This bibliography includes studies from across the oil- and natural-gas-producing areas of the conterminous United States that were published in the last 80 yrs. The studies describe the effects of produced water salts on soils, water quality, and ecosystems. Also included are reports that describe (1) the inorganic chemistry of produced waters included in studies of formation waters for various purposes, (2) other sources of salt affecting water quality that may be mistaken for produced water effects, (3) geochemical and geophysical techniques that allow discrimination of salt sources, (4) remediation technologies designed to repair damage caused to soils and ground water by produced water salts, and (5) contamination by

  12. Compact type mutants in apple and sour cherries

    International Nuclear Information System (INIS)

    Zagaja, S.W.; Przybyla, A.

    1976-01-01

    Induction of mutations in deciduous fruits is considered complementary to the conventional breeding methods. Several promissing mutants, particularly in apples, were described and some of them were introduced to commercial orchards. Studies described herein are aimed at developing compact type mutants in apple cultivars, apple rootstocks and in sour cherry cultivars. Data obtained so far confirm the results of the other authors, who developed compact type mutants in apples and sweet cherries. Physiological studies have shown that the leaves of spontaneous apple mutants of compact type are more efficient in photosynthesis than the leaves of respective standards. In spite of this, using branch ringing techniques, it was found that the leaves of compacts and those of standards do not differ in their productivity. There seem to be several advantages in employing tissue culture technique in mutation breeding. That is why a project was started to work out a method of growing apple shoots from adventitious buds developed on sections of roots. (author)

  13. Partitioning of semi-soluble organic compounds between the water phase and oil droplets in produced water

    Energy Technology Data Exchange (ETDEWEB)

    Faksness, Liv-Guri; Grini, Per Gerhard; Daling, Per S

    2004-04-01

    When selecting produced water treatment technologies, one should focus on reducing the major contributors to the total environmental impact. These are dispersed oil and semi-soluble hydrocarbons, alkylated phenols, and added chemicals. Experiments with produced water have been performed offshore on the Statoil operated platforms Gullfaks C and Statfjord B. These experiments were designed to find how much of the environmentally relevant compounds were dissolved in the water phase and not associated to the dispersed oil in the produced water. Results show that the distribution between the dispersed oil and the water phase varies highly for the different components groups. For example the concentration of PAHs and the C6-C9 alkylated phenols is strongly correlated to the content of dispersed oil. Therefore, the technologies enhancing the removal of dispersed oil have a higher potential for reducing the environmental impact of the produced water than previously considered.

  14. Partitioning of semi-soluble organic compounds between the water phase and oil droplets in produced water

    International Nuclear Information System (INIS)

    Faksness, Liv-Guri; Grini, Per Gerhard; Daling, Per S.

    2004-01-01

    When selecting produced water treatment technologies, one should focus on reducing the major contributors to the total environmental impact. These are dispersed oil and semi-soluble hydrocarbons, alkylated phenols, and added chemicals. Experiments with produced water have been performed offshore on the Statoil operated platforms Gullfaks C and Statfjord B. These experiments were designed to find how much of the environmentally relevant compounds were dissolved in the water phase and not associated to the dispersed oil in the produced water. Results show that the distribution between the dispersed oil and the water phase varies highly for the different components groups. For example the concentration of PAHs and the C6-C9 alkylated phenols is strongly correlated to the content of dispersed oil. Therefore, the technologies enhancing the removal of dispersed oil have a higher potential for reducing the environmental impact of the produced water than previously considered

  15. Development of device producing electrolyzed water for home care

    International Nuclear Information System (INIS)

    Umimoto, K; Nagata, S; Yanagida, J

    2013-01-01

    When water containing ionic substances is electrolyzed, electrolyzed water with strong bactericidal ability due to the available chlorine(AC) is generated on the anode side. Slightly acidic to neutral electrolyzed water (pH 6.5 to 7.5) is physiological pH and is suitable for biological applications. For producing slightly acidic to neutral electrolyzed water simply, a vertical-type electrolytic tank with an asymmetric structure was made. As a result, a small amount of strongly alkaline water was generated in the upper cathodic small chamber, and a large amount of weakly acidic water generated in the lower anodic large chamber. The pH and AC concentration in solutin mixed with both electrolyzed water were 6.3 and 39.5 ppm, respectively, This solution was slightly acidic to neutral electrolyzed water and had strong bactericidal activity. This device is useful for producing slightly acidic to neutral electrolyzed water as a disinfectant to employ at home care, when considering economic and environmental factors, since it returns to ordinary water after use.

  16. TREATMENT OF PRODUCED OIL AND GAS WATERS WITH SURFACTANT-MODIFIED ZEOLITE

    Energy Technology Data Exchange (ETDEWEB)

    Lynn E. Katz; R.S. Bowman; E.J. Sullivan

    2003-11-01

    Co-produced water from the oil and gas industry accounts for a significant waste stream in the United States. It is by some estimates the largest single waste stream in the country, aside from nonhazardous industrial wastes. Characteristics of produced water include high total dissolved solids content, dissolved organic constituents such as benzene and toluene, an oil and grease component, and chemicals added during the oil-production process. While most of the produced water is disposed via reinjection, some must be treated to remove organic constituents before the water is discharged. Current treatment options are successful in reducing the organic content; however, they cannot always meet the levels of current or proposed regulations for discharged water. Therefore, an efficient, cost-effective treatment technology is needed. Surfactant-modified zeolite (SMZ) has been used successfully to treat contaminated ground water for organic and inorganic constituents. In addition, the low cost of natural zeolites makes their use attractive in water-treatment applications. This report summarizes the work and results of this four-year project. We tested the effectiveness of surfactant-modified zeolite (SMZ) for removal of BTEX with batch and column experiments using waters with BTEX concentrations that are comparable to those of produced waters. The data from our experimental investigations showed that BTEX sorption to SMZ can be described by a linear isotherm model, and competitive effects between compounds were not significant. The SMZ can be readily regenerated using air stripping. We field-tested a prototype SMZ-based water treatment system at produced water treatment facilities and found that the SMZ successfully removes BTEX from produced waters as predicted by laboratory studies. When compared to other existing treatment technologies, the cost of the SMZ system is very competitive. Furthermore, the SMZ system is relatively compact, does not require the storage of

  17. Precipitation of metals in produced water : influence on contaminant transport and toxicity

    International Nuclear Information System (INIS)

    Azetsu-Scott, K.; Wohlgeschaffen, G.; Yeats, P.; Dalziel, J.; Niven, S.; Lee, K.

    2006-01-01

    Produced water contains a number of compounds of environmental concern and is the largest volume waste stream from oil and gas production activities. Recent studies have shown that chemicals dissolved in waste water from oil platforms stunted the growth of North Sea cod and affected their breeding patterns. Scientific research is needed to identify the impact of produced water discharges on the environment as well as to identify acceptable disposal limits for produced water. This presentation provided details of a study to characterize produced water discharged within the Atlantic regions of Canada. The study included dose response biological effect studies; research on processes controlling the transport and transformation of contaminants associated with produced water discharges and the development of risk assessment models. The sample location for the study was a site near Sable Island off the coast of Nova Scotia. Chemical analysis of the produced water was conducted as well as toxicity tests. Other tests included a time-series particulate matter sedimentation test; time-series metal and toxicity analysis; time-series change in metal precipitates tests and a produced water/seawater layering experiment. Dissolved and particulate fractions were presented, and the relationship between toxicity and particulate concentrations was examined. Results of the study suggested that produced water contaminants are variable over spatial and temporal scales due to source variations and changes in discharge rates. Chemical changes occur within 24 hours of produced water being mixed with seawater and facilitate contaminant partitioning between the surface micro layer, water column and sediments. Changes in the toxicity of the produced water are correlated with the partitioning of chemical components. The impact zone may be influenced by chemical kinetics that control the distribution of potential toxic metals. Further research is needed to investigate the effects of low level

  18. Produced Water Reuse Considerations for In-Situ Recovery: a Case Development

    Energy Technology Data Exchange (ETDEWEB)

    Kus, J.; Card, R.

    1984-01-01

    Steam-assisted methods for in-situ recovery in Canada typically operate at steam to oil ratios of approximately 3 to 1 and generate in the order of 2 to 5 barrels of produced water per barrel of production. To raise the large quantities of steam required for reservoir stimulation, once-through type steam generators are most commonly used. They are typically designed to produce about 80 per cent quality steam from soft, oil-free feedwater. Suncor Inc operates a cyclic steam injection pilot project near Fort Kent, Alberta. In the early 1980s, Suncor planned an expansion of the 180 m/sup 3//d (1,130 bbl/d) facility to 800 m/sup 3//d (5,000 bbl/d). The expansion necessitated the development of a reliable water supply. Preliminary investigations into the feasibility of reusing produced water as the sole source of supply for the project expansion revealed this to be a costly and technically high risk option, given the specific produced water characteristics. As a result, an innovative alternative was developed to use a blend of produced water and municipal effluent from a nearby town as the water supply. This paper presents the rationale for the selection of this unique water supply and the process design considerations for the resulting water treatment system.

  19. The Effect of Green Tea versus Sour Tea on Insulin Resistance, Lipids Profiles and Oxidative Stress in Patients with Type 2 Diabetes Mellitus: A Randomized Clinical Trial

    Directory of Open Access Journals (Sweden)

    Hassan Mozaffari-Khosravi

    2014-09-01

    Full Text Available Background: By decreasing oxidative stress and whereby decreasing insulin resistance, it may be possible to decrease complications of Diabetes Mellitus (DM. Green tea and sour tea contain phytochemicals which have anti-oxidative function. The aim of this study is to compare the effect of sour and green tea consumption on insulin resistance and oxidative stress in DM. Methods: This study is a randomized clinical trial in which 100 type 2 diabetes patients were randomly assigned into sour tea group (ST and green tea group (GT. The patients were instructed to drink 150ml sour tea and green tea infusion, respectively, three times a day for 4 weeks. Fasting blood sugar (FBS, fructosamine, lipid profiles, fasting blood insulin (FBI, homeostasis model assessment of insulin resistance (HOMA-IR; beta cell function (b%, insulin sensitivity (S% and malondialdehyde (MDA were monitored. Results: HDL-c significantly increased in both groups. The median of FBI in GT showed significant decrease (8.5 to 6.6 μIU/mL unlike the ST which showed significant increase (8.2 to 16.3 μIU/mL. The median of HOMA-IR after the intervention in GT showed lower levels than the ST (1.1 vs. 1.6, P=0.004. The median of b% only in ST showed significant increase from 38.2% at the baseline to 47.7% after the intervention. The mean of S% only in ST showed significant decrease after the intervention. Conclusion: This study shows that the use of 150 ml infusion of green tea or sour tea, three times a day for four weeks, has positive effect on insulin resistance and certain lipoproteins in type 2 DM. Trial Registration Number: IRCT201107317161N1

  20. Reservoir souring: Problems, uncertainties and modelling. Part I: Problems and uncertainty involved in prediction. Part II: Preliminary investigations of a computational model

    International Nuclear Information System (INIS)

    Paulsen, J.E.; Read, P.A.; Thompson, C.P.; Jelley, C.; Lezeau, P.

    1996-01-01

    The paper relates to improved oil recovery (IOR) techniques by mathematical modelling. The uncertainty involved in modelling of reservoir souring is discussed. IOR processes are speculated to influence a souring process in a positive direction. Most models do not take into account pH in reservoir fluids, and thus do not account for partitioning behaviour of sulfide. Also, sulfide is antagonistic to bacterial metabolism and impedes to bacterial metabolism and impedes the sulfate reduction rate, this may be an important factor in modelling. Biofilms are thought to play a crucial role in a reservoir souring process. Biofilm in a reservoir matrix is different from biofilm in open systems. This has major impact on microbial impact on microbial transport and behaviour. Studies on microbial activity in reservoir matrices must be carried out with model cores, in order to mimic a realistic situation. Sufficient data do not exist today. The main conclusion is that a model does not reflect a true situation before the nature of these elements is understood. A simplified version of an Norwegian developed biofilm model is discussed. The model incorporates all the important physical phenomena studied in the above references such as bacteria growth limited by nutrients and/or energy sources and hydrogen sulfide adsorption. 18 refs., 8 figs., 1 tab

  1. Reservoir souring: Problems, uncertainties and modelling. Part I: Problems and uncertainty involved in prediction. Part II: Preliminary investigations of a computational model

    Energy Technology Data Exchange (ETDEWEB)

    Paulsen, J.E. [Rogalandsforskning, Stavanger (Norway); Read, P.A.; Thompson, C.P.; Jelley, C.; Lezeau, P.

    1996-12-31

    The paper relates to improved oil recovery (IOR) techniques by mathematical modelling. The uncertainty involved in modelling of reservoir souring is discussed. IOR processes are speculated to influence a souring process in a positive direction. Most models do not take into account pH in reservoir fluids, and thus do not account for partitioning behaviour of sulfide. Also, sulfide is antagonistic to bacterial metabolism and impedes to bacterial metabolism and impedes the sulfate reduction rate, this may be an important factor in modelling. Biofilms are thought to play a crucial role in a reservoir souring process. Biofilm in a reservoir matrix is different from biofilm in open systems. This has major impact on microbial impact on microbial transport and behaviour. Studies on microbial activity in reservoir matrices must be carried out with model cores, in order to mimic a realistic situation. Sufficient data do not exist today. The main conclusion is that a model does not reflect a true situation before the nature of these elements is understood. A simplified version of an Norwegian developed biofilm model is discussed. The model incorporates all the important physical phenomena studied in the above references such as bacteria growth limited by nutrients and/or energy sources and hydrogen sulfide adsorption. 18 refs., 8 figs., 1 tab.

  2. Minimizing water consumption when producing hydropower

    Science.gov (United States)

    Leon, A. S.

    2015-12-01

    In 2007, hydropower accounted for only 16% of the world electricity production, with other renewable sources totaling 3%. Thus, it is not surprising that when alternatives are evaluated for new energy developments, there is strong impulse for fossil fuel or nuclear energy as opposed to renewable sources. However, as hydropower schemes are often part of a multipurpose water resources development project, they can often help to finance other components of the project. In addition, hydropower systems and their associated dams and reservoirs provide human well-being benefits, such as flood control and irrigation, and societal benefits such as increased recreational activities and improved navigation. Furthermore, hydropower due to its associated reservoir storage, can provide flexibility and reliability for energy production in integrated energy systems. The storage capability of hydropower systems act as a regulating mechanism by which other intermittent and variable renewable energy sources (wind, wave, solar) can play a larger role in providing electricity of commercial quality. Minimizing water consumption for producing hydropower is critical given that overuse of water for energy production may result in a shortage of water for other purposes such as irrigation, navigation or fish passage. This paper presents a dimensional analysis for finding optimal flow discharge and optimal penstock diameter when designing impulse and reaction water turbines for hydropower systems. The objective of this analysis is to provide general insights for minimizing water consumption when producing hydropower. This analysis is based on the geometric and hydraulic characteristics of the penstock, the total hydraulic head and the desired power production. As part of this analysis, various dimensionless relationships between power production, flow discharge and head losses were derived. These relationships were used to withdraw general insights on determining optimal flow discharge and

  3. Strategic conservation of orchard germplasm based on indigenous knowledge and genetic diversity: a case study of sour orange populations in China.

    Science.gov (United States)

    Ming, Feng; Liu, Qi-Kun; Shi, Jin-Lei; Wang, Wei; Lu, Bao-Rong

    2009-01-01

    To effectively conserve sour orange (Citrus aurantium L.) germplasm on two islands at the estuary of the Yangtze River in China, we estimated genetic variation and relationships of the known parental trees and their proposed descendents (young trees) using the fingerprints of random amplified polymorphic DNA (RAPD). Results based on RAPD analyses showed considerable genetic diversity in the parental populations (H(e)=0.202). The overall populations including the parental and young trees showed slightly higher genetic diversity (H(e)=0.298) than the parents, with about 10% variation between populations. An unweighted pair group method with arithmetic mean analysis dendrogram based on cluster analysis of the Jaccard similarity among individuals demonstrated a more complicated relationship of the parental and young trees from the two islands, although the young trees showed a clear association with parental trees. This indicates a significant contribution of parental trees in establishing the sour orange populations on the two islands. According to farmers' knowledge, conservation of only one or two parental trees would be sufficient because they believed that the whole populations were generated from a single mother tree. However, this study suggests that preserving most parental trees and some selected young trees with distant genetic relationships should be an effective conservation strategy for sour orange germplasm on the two islands.

  4. Putting produced water to a useful purpose : regulatory gaps and other concerns

    International Nuclear Information System (INIS)

    Kwasniak, A.J.

    2006-01-01

    This presentation discussed issues related to produced water from oil and gas activities and its use and disposal in Alberta. The province is in danger of a water shortage, and studies have shown that runoff volumes in the South Saskatchewan River Basin (SSRB) are below average. A recent assessment of 33 river reaches in the SSRB has shown that 31 river reaches are approaching ecologically unacceptable values. Water produced from coalbed methane (CBM) activities will be only marginally saline or non-saline, and CBM activities are expected to increase in the region in order to supplement Alberta's dwindling natural gas supplies. Approximately 10 per cent of the CBM wells drilled in 2004 targeted seams that contained water. Approximately 50,000 more CBM wells will be drilled in Alberta in the next decade. While water conservation will help to address the situation, the re-use of produced water in processing technologies will help to reduce the impact of oil and gas activities in the province. However, regulatory difficulties may prevent produced water from being re-used. It is not currently known whether operators require a water rights permit to produce water. Regulatory obligations concerning damage to aquifers and water discharges are also unclear. The Water Act currently requires statutory authorizations for diversions of water. If the water is non-saline, then the operator is required to obtain a licence to divert produced water from its source. It was concluded that clear legislation is needed to determine if water can be re-used after it is brought to the surface. The introduction of an American-style beneficial rights use was recommended. refs., tabs., figs

  5. WATER PINCH TECHNOLOGY APPLICATION TO MINIMIZE SULPHUROUS WASTEWATER IN AN OIL REFINERY

    Directory of Open Access Journals (Sweden)

    Gabriel Orlando Lobelles Sardiñas

    2017-01-01

    Full Text Available In oil refining industries there is a high water consumption, which influences the high production costs and impacts the environment due to the discharge of their wastes. It is known that there are no technological conditions for the reuse of industrial water at the oil refineries, based on hydroskimming processes. The objective of this study is to implement the process integration methodology, Water Pinch, to a sour water stripper unit, as a unitary process of an oil refinery, to minimize the amount of sulphurous waste water and reduce contamination of the bay that receives these wastes. The technology is applied to evaluate the volume of sulphurous wastewater generated in the Cienfuegos oil refinery. This technology allows identifying opportunities for recovery and reuse of water, based on concentration ranges of contaminants. To achieve this purpose, a sour water stripper tower was assessed with the help of Water Pinch software, which provided an optimized distribution network, as a proposed technological improvement. This facilitated to recover and reuse 667 757, 28 m3 of water per year, and 1 035 023, 78 CUC were saved, at the same time the amount of polluting effluents decreased in approximately 2 % of non-reusable treated water.

  6. Purification of produced waters in oil fields

    Energy Technology Data Exchange (ETDEWEB)

    Niyazov, R S; Baikov, U M

    1970-01-01

    Experience has shown that a single step water-conditioning process cannot be used to prepare Bashkirian produced waters for underground injection. In the single-step process, the water is passed through horizontal or vertical settling basins to remove solids. This system does not work when suspended solids increase above 200 to 500 mg/liter. The required quality of injection water can be obtained by filtering the water through sand at flow velocities of 5 to 10 m/hr. The filter has a sand layer 0.6 to 1 m thick, composed of 0.35 to 1.0 mm sand. Water entering the filters should not contain more than 100 to 150 mg/liter of oil products. The filters are backwashed at velocity of 10 to 15 m/hr and rates of 12 to 16 liters/sec sq m for 10 to 15 min. Clean water is used in backwashing. When surfactant is added to the backwash water, the filter cycle lasts longer.

  7. Is it possible to treat produced water for recycle and beneficial reuse?

    Energy Technology Data Exchange (ETDEWEB)

    Hum, F.; Tsang, P.; Kantzas, A.; Harding, T. [Calgary Univ., AB (Canada). Tomographic Imaging and Porous Media Laboratory

    2005-11-01

    In 2003, the oil and gas industry in Alberta injected 0.3 billion cubic metres of produced water into disposal wells. This paper addressed the issue of using the large volume of produced water for recycling and make water reuse a sustainable activity in Alberta to reduce fresh water demand. Although produced water represents a potential resource for recycling and beneficial reuse, it must first be treated to meet water quality criteria and regulatory guidelines for specific applications. A comprehensive technical and economic review of water treatment technologies was presented. Commonly used and new water desalination technologies were reviewed and key challenges associated with the recycling of produced water were identified. It was shown that water treatment processes are commercially available and that they are not prohibitively expensive. However, the cost of implementing treating processes to meet drinking water quality guidelines is about 3 times the current cost of municipal water supply in Alberta. For that reason, it is more feasible to recycle waste water for agricultural or petroleum applications, such as waterflooding. The water quality guidelines for these other purposes are less stringent than for drinking water and there is also growing public resistance for industry to use fresh water for commercial use. 42 refs., 3 tabs., 14 figs.

  8. Desalination of Produced Water via Gas Hydrate Formation and Post Treatment

    OpenAIRE

    Niu, Jing

    2012-01-01

    This study presents a two-step desalination process, in which produced water is cleaned by forming gas hydrate in it and subsequently dewatering the hydrate to remove the residual produced water trapped in between the hydrate crystals. All experiments were performed with pressure in the range of 450 to 800psi and temperature in the range of -1 to 1°C using CO? as guest molecule for the hydrate crystals. The experiments were conducted using artificial produced waters containing different amoun...

  9. [Health effects of sour cherries with unique polyphenolic composition in their fruits].

    Science.gov (United States)

    Hegedűs, Attila; Papp, Nóra; Blázovics, Anna; Stefanovitsné Bányai, Éva

    2018-05-01

    Health effects of fruit consumption are confirmed by many studies. Such effects are attributed to the polyphenolic compounds accumulating in fruit skin and mesocarp tissues. They contribute to the regulation on transcriptional, post-transcriptional and epigenetic levels. Since people consume much less fruits than the recommended quantities, a new approach includes the promotion of super fruits that are extremely rich sources of specific health compounds. A comparative analysis of Hungarian stone fruit cultivars detected a huge variability in fruit in vitro antioxidant capacity and total polyphenolic content. Two outstanding sour cherry cultivars ('Pipacs 1' and 'Fanal') were identified to accumulate elevated levels of polyphenolic compounds in their fruits. Sour cherries with different polyphenolic compositions were tested against alimentary induced hyperlipidemia using male Wistar rat model. Consumption of cherry fruit had different consequences for different cultivars: consumption of 'Pipacs 1' and 'Fanal' fruits resulted in 30% lower total cholesterol levels in the sera of hyperlipidemic animals after only 10 days of treatment. However, the consumption of 'Újfehértói fürtös' fruit has not induced significant alterations in the same parameter. Other lipid parameters also reflected the short-term beneficial effects of 'Pipacs 1' and 'Fanal' fruits. We suggest that not only some tropical and berry fruits might be considered as super fruits but certain genotypes of stone fruits as well. These have indeed marked physiological effects. Since 'Pipacs 1' and 'Fanal' are rich sources of colourless polyphenolics (e.g., phenolic acids and isoflavonoids) and anthocyanins, respectively, the protective effects associated with their consumption can be attributed to different polyphenolic compounds. Orv Hetil. 2018; 159(18): 720-725.

  10. Evaluation of the Physico-Chemical Properties of Produced Water ...

    African Journals Online (AJOL)

    ADOWIE PERE

    Samples were obtained at different periods within two months. Produced water ... sometimes, naturally occurring radioactive materials .... particular sample of soil, water, or air (Khatib and ... several other elements in solution particularly Barium.

  11. Assessment of physicochemical quality of sachet water produced in ...

    African Journals Online (AJOL)

    Fifty (50) brands of sachet water produced from bore hole and tap water in five (5) local government areas of Kano metropolis were analysed for physicochemical quality. Ten (10) brands of sachet water were sampled from each of the five (5) local government areas of; Nasarawa, Tarauni, Gwale, Kumbotso and Ungogo.

  12. Microsatellite marker development by partial sequencing of the sour passion fruit genome (Passiflora edulis Sims).

    Science.gov (United States)

    Araya, Susan; Martins, Alexandre M; Junqueira, Nilton T V; Costa, Ana Maria; Faleiro, Fábio G; Ferreira, Márcio E

    2017-07-21

    The Passiflora genus comprises hundreds of wild and cultivated species of passion fruit used for food, industrial, ornamental and medicinal purposes. Efforts to develop genomic tools for genetic analysis of P. edulis, the most important commercial Passiflora species, are still incipient. In spite of many recognized applications of microsatellite markers in genetics and breeding, their availability for passion fruit research remains restricted. Microsatellite markers in P. edulis are usually limited in number, show reduced polymorphism, and are mostly based on compound or imperfect repeats. Furthermore, they are confined to only a few Passiflora species. We describe the use of NGS technology to partially assemble the P. edulis genome in order to develop hundreds of new microsatellite markers. A total of 14.11 Gbp of Illumina paired-end sequence reads were analyzed to detect simple sequence repeat sites in the sour passion fruit genome. A sample of 1300 contigs containing perfect repeat microsatellite sequences was selected for PCR primer development. Panels of di- and tri-nucleotide repeat markers were then tested in P. edulis germplasm accessions for validation. DNA polymorphism was detected in 74% of the markers (PIC = 0.16 to 0.77; number of alleles/locus = 2 to 7). A core panel of highly polymorphic markers (PIC = 0.46 to 0.77) was used to cross-amplify PCR products in 79 species of Passiflora (including P. edulis), belonging to four subgenera (Astrophea, Decaloba, Distephana and Passiflora). Approximately 71% of the marker/species combinations resulted in positive amplicons in all species tested. DNA polymorphism was detected in germplasm accessions of six closely related Passiflora species (P. edulis, P. alata, P. maliformis, P. nitida, P. quadrangularis and P. setacea) and the data used for accession discrimination and species assignment. A database of P. edulis DNA sequences obtained by NGS technology was examined to identify microsatellite repeats in

  13. Method of producing deuterium-oxide-enriched water

    International Nuclear Information System (INIS)

    Mandel, H.

    1976-01-01

    A method and apparatus for producing deuterium-oxide-enriched water (e.g., as a source of deuterium-rich gas mixtures) are disclosed wherein the multiplicity of individual cooling cycles of a power plant are connected in replenishment cascade so that fresh feed water with a naturally occurring level of deuterium oxide is supplied to replace the vaporization losses, sludge losses and withdrawn portion of water in a first cooling cycle, the withdrawn water being fed as the feed water to the subsequent cooling cycle or stage and serving as the sole feed-water input to the latter. At the end of the replenishment-cascade system, the withdrawn water has a high concentration of deuterium oxide and may serve as a source of water for the production of heavy water or deuterium-enriched gas by conventional methods of removing deuterium oxide or deuterium from the deuterium-oxide-enriched water. Each cooling cycle may form part of a thermal or nuclear power plant in which a turbine is driven by part of the energy and air-cooling of the water takes place in the atmosphere, e.g., in a cooling tower

  14. Application of nanotechnologies for solving ecological problems on produced water utilization

    International Nuclear Information System (INIS)

    Hajiyev, S.K.; Kalbaliyeva, E.S.; Kazimov, F.K.

    2010-01-01

    Utilization of produced water is connected with the problems of its purification, repeated use and following the corresponding ecological requirements.Constant growth of the amount of produced water in extracted fluid and contaminating components require improvement of existing methods of utilization and development of advanced technologies. In the result of development of nanocomposites on the base of metallic nanoparticles it has been achieved significant improvement of purification efficiency of produced water, as well as decrease of surface tension, viscosity, increase of corrosion resistance and protection against salt deposition.

  15. The Effect of Green Tea and Sour Tea (Hibiscus sabdariffa L.) Supplementation on Oxidative Stress and Muscle Damage in Athletes.

    Science.gov (United States)

    Hadi, Amir; Pourmasoumi, Makan; Kafeshani, Marzieh; Karimian, Jahangir; Maracy, Mohammad Reza; Entezari, Mohammad Hasan

    2017-05-04

    Additional oxygen consumption during intense exercises may lead to oxidative stress and contribute to muscular fatigue. Green tea and sour tea (Hibiscus sabdariffa L.), which contain various flavonoids and polyphenols, have many healthful properties such as anticarcinogenic, anti-inflammatory, and heart protecting effects. The aim of the present study was to assess the effects of green tea and sour tea supplementation on oxidative stress and muscle damage in soccer athletes. This randomized, double-blind control trial was conducted on 54 male soccer players. Participants were randomly assigned to three groups to receive: 450 mg/d green tea extract (GTE) in the first group (n = 18), 450 mg/d sour tea extract (STE) in the second group (n = 18) and 450 mg/d maltodextrin in the control group (n = 18). Fasting whole blood samples were taken under resting conditions at the beginning and the end of the study to quantify the serum levels of muscle damage indices, aspartate aminotransferase (AST), creatine kinase (CK), lactate dehydrogenase (LDH), and oxidative stress biomarkers, malondialdehyde (MDA), and total antioxidant capacity (TAC). After six weeks intervention, athletes who received GTE and STE supplements compared with the placebo had a significantly decreased MDA level (P = 0.008). Furthermore, STE supplementation resulted in a significant increase in TAC level compared with GTE and placebo groups (P = 0.01). However, supplementation with GTE and STE had no significant effects on muscle damage indices. GTE and STE supplementation have beneficial effects on oxidative stress status in male athletes. However, both kinds of tea extract did not affect muscle damage status.

  16. Method for excluding salt and other soluble materials from produced water

    Science.gov (United States)

    Phelps, Tommy J [Knoxville, TN; Tsouris, Costas [Oak Ridge, TN; Palumbo, Anthony V [Oak Ridge, TN; Riestenberg, David E [Knoxville, TN; McCallum, Scott D [Knoxville, TN

    2009-08-04

    A method for reducing the salinity, as well as the hydrocarbon concentration of produced water to levels sufficient to meet surface water discharge standards. Pressure vessel and coflow injection technology developed at the Oak Ridge National Laboratory is used to mix produced water and a gas hydrate forming fluid to form a solid or semi-solid gas hydrate mixture. Salts and solids are excluded from the water that becomes a part of the hydrate cage. A three-step process of dissociation of the hydrate results in purified water suitable for irrigation.

  17. Microbial Species Diversity, Community Dynamics, and Metabolite Kinetics of Water Kefir Fermentation

    Science.gov (United States)

    Laureys, David

    2014-01-01

    Water kefir is a sour, alcoholic, and fruity fermented beverage of which the fermentation is started with water kefir grains. These water kefir grains consist of polysaccharide and contain the microorganisms responsible for the water kefir fermentation. In this work, a water kefir fermentation process was followed as a function of time during 192 h to unravel the community dynamics, the species diversity, and the kinetics of substrate consumption and metabolite production. The majority of the water kefir ecosystem was found to be present on the water kefir grains. The most important microbial species present were Lactobacillus casei/paracasei, Lactobacillus harbinensis, Lactobacillus hilgardii, Bifidobacterium psychraerophilum/crudilactis, Saccharomyces cerevisiae, and Dekkera bruxellensis. The microbial species diversities in the water kefir liquor and on the water kefir grains were similar and remained stable during the whole fermentation process. The major substrate, sucrose, was completely converted after 24 h of fermentation, which coincided with the production of the major part of the water kefir grain polysaccharide. The main metabolites of the fermentation were ethanol and lactic acid. Glycerol, acetic acid, and mannitol were produced in low concentrations. The major part of these metabolites was produced during the first 72 h of fermentation, during which the pH decreased from 4.26 to 3.45. The most prevalent volatile aroma compounds were ethyl acetate, isoamyl acetate, ethyl hexanoate, ethyl octanoate, and ethyl decanoate, which might be of significance with respect to the aroma of the end product. PMID:24532061

  18. Microbial species diversity, community dynamics, and metabolite kinetics of water kefir fermentation.

    Science.gov (United States)

    Laureys, David; De Vuyst, Luc

    2014-04-01

    Water kefir is a sour, alcoholic, and fruity fermented beverage of which the fermentation is started with water kefir grains. These water kefir grains consist of polysaccharide and contain the microorganisms responsible for the water kefir fermentation. In this work, a water kefir fermentation process was followed as a function of time during 192 h to unravel the community dynamics, the species diversity, and the kinetics of substrate consumption and metabolite production. The majority of the water kefir ecosystem was found to be present on the water kefir grains. The most important microbial species present were Lactobacillus casei/paracasei, Lactobacillus harbinensis, Lactobacillus hilgardii, Bifidobacterium psychraerophilum/crudilactis, Saccharomyces cerevisiae, and Dekkera bruxellensis. The microbial species diversities in the water kefir liquor and on the water kefir grains were similar and remained stable during the whole fermentation process. The major substrate, sucrose, was completely converted after 24 h of fermentation, which coincided with the production of the major part of the water kefir grain polysaccharide. The main metabolites of the fermentation were ethanol and lactic acid. Glycerol, acetic acid, and mannitol were produced in low concentrations. The major part of these metabolites was produced during the first 72 h of fermentation, during which the pH decreased from 4.26 to 3.45. The most prevalent volatile aroma compounds were ethyl acetate, isoamyl acetate, ethyl hexanoate, ethyl octanoate, and ethyl decanoate, which might be of significance with respect to the aroma of the end product.

  19. Environmental contaminants in oil field produced waters discharged into wetlands

    International Nuclear Information System (INIS)

    Ramirez, P. Jr.

    1994-01-01

    The 866-acre Loch Katrine wetland complex in Park County, Wyoming provides habitat for many species of aquatic birds. The complex is sustained primarily by oil field produced waters. This study was designed to determine if constituents in oil field produced waters discharged into Custer Lake and to Loch Katrine pose a risk to aquatic birds inhabiting the wetlands. Trace elements, hydrocarbons and radium-226 concentrations were analyzed in water, sediment and biota collected from the complex during 1992. Arsenic, boron, radium-226 and zinc were elevated in some matrices. The presence of radium-226 in aquatic vegetation suggests that this radionuclide is available to aquatic birds. Oil and grease concentrations in water from the produced water discharge exceeded the maximum 10 mg/l permitted by the WDEQ (1990). Total aliphatic and aromatic hydrocarbon concentrations in sediments were highest at the produced water discharge, 6.376 μg/g, followed by Custer Lake, 1.104 μg/g. The higher levels of hydrocarbons found at Custer Lake, compared to Loch Katrine, may be explained by Custer Lake's closer proximity to the discharge. Benzo(a)pyrene was not detected in bile from gadwalls collected at Loch Katrine but was detected in bile from northern shovelers collected at Custer Lake. Benzo(a)pyrene concentrations in northern shoveler bile ranged from 500 to 960 ng/g (ppb) wet weight. The presence of benzo(a)pyrene in the shovelers indicates exposure to petroleum hydrocarbons

  20. Energy consumption in desalinating produced water from shale oil and gas extraction

    OpenAIRE

    Tow, Emily W.; Chung, Hyung Won; Lienhard, John H.; Thiel, Gregory Parker; Banchik, Leonardo David

    2014-01-01

    On-site treatment and reuse is an increasingly preferred option for produced water management in unconventional oil and gas extraction. This paper analyzes and compares the energetics of several desalination technologies at the high salinities and diverse compositions commonly encountered in produced water from shale formations to guide technology selection and to inform further system development. Produced water properties are modeled using Pitzer's equations, and emphasis is placed on how t...

  1. Determining the water cut and water salinity in an oil-water flowstream by measuring the sulfur content of the produced oil

    International Nuclear Information System (INIS)

    Smith, H.D.; Arnold, D.M.

    1980-01-01

    A technique for detecting water cut and water salinity in an oil/water flowstream in petroleum refining and producing operations is described. The fluid is bombarded with fast neutrons which are slowed down and then captured producing gamma spectra characteristic of the fluid material. Analysis of the spectra indicates the relative presence of the elements sulfur, hydrogen and chlorine and from the sulfur measurement, the oil cut (fractional oil content) of the fluid is determined, enabling the water cut to be found. From the water cut, water salinity can also be determined. (U.K.)

  2. Barium in produced water: Is it a toxicological hazard to the marine environment?

    International Nuclear Information System (INIS)

    Neff, J.M.

    1993-01-01

    Produced water is a complex aqueous mixture of organic and inorganic chemicals that often is generated in large volumes as a by-product of production of oil and gas. Produced water from offshore oil production platforms sometimes is treated to remove particulate oil and then discharged to the ocean. Barium often is the most abundant inorganic chemical, other than the dominant sea salts, in produced water. Some concern has been expressed that the large amounts of barium discharged to the ocean in produced water may have adverse effects on marine biological communities. The ecological risks associated with discharge to the ocean in produced water may have adverse effects on marine biological communities. The ecological risks associated with discharge to the ocean of barium in produced water were evaluated. Concentrations of barium in produced water from different sources range from less than 1.0 to about 2,000 mg/L, and are inversely correlated with concentrations of sulfate. Concentrations of barium in the ocean usually are in the range of 10 to 20 μg/L; the ocean is undersaturated with respect to barite (BaSO 4 ). During mixing and dilution of a produced water plume in the ocean, barium reacts with the abundant sulfate in seawater and precipitates as barite. Barite is completely nontoxic to marine organisms. Because of the high concentration of sulfate in the ocean, ionic barium can not reach concentrations high enough to be toxic to marine organisms

  3. Occurrence of carbapenemase-producing bacteria in coastal recreational waters.

    Science.gov (United States)

    Montezzi, Lara Feital; Campana, Eloiza Helena; Corrêa, Laís Lisboa; Justo, Livia Helena; Paschoal, Raphael Paiva; da Silva, Isabel Lemos Vieira Dias; Souza, Maria do Carmo Maciel; Drolshagen, Marcia; Picão, Renata Cristina

    2015-02-01

    The spread of carbapenemase-producing Gram-negative rods is an emerging global problem. Although most infections due to carbapenemase producers are limited to healthcare institutions, reports of the occurrence of clinically relevant carbapenemase producers in sewage and polluted rivers are increasingly frequent. Polluted rivers flowing to oceans may contaminate coastal waters with multidrug-resistant bacteria, potentially threatening the safety of recreational activities in these locations. Here we assessed the occurrence of carbapenemase producers in water from touristic beaches located in Rio de Janeiro, Brazil, showing distinct pollution patterns. The presence of enterobacteria was noted, including the predominantly environmental genus Kluyvera spp., producing either Klebsiella pneumoniae carbapenemase (KPC) or Guyana extended-spectrum (GES)-type carbapenemases and often associated with quinolone resistance determinants. An Aeromonas sp. harbouring blaKPC and qnrS was also observed. These findings strengthen the role of aquatic matrices as reservoirs and vectors of clinically relevant antimicrobial-resistant bacteria, with potential to favour the spread of these resistance threats throughout the community. Copyright © 2014 Elsevier B.V. and the International Society of Chemotherapy. All rights reserved.

  4. High-efficiency low LCOE combined cycles for sour gas oxy-combustion with CO[subscript 2] capture

    OpenAIRE

    Chakroun, Nadim Walid; Ghoniem, Ahmed F

    2015-01-01

    The growing concerns over global warming and carbon dioxide emissions have driven extensive research into novel ways of capturing carbon dioxide in power generation plants. In this regard, oxy-fuel combustion has been considered as a promising technology. One unconventional fuel that is considered is sour gas, which is a mixture of methane, hydrogen sulfide and carbon dioxide. In this paper, carbon dioxide is used as the dilution medium in the combustor and different combined cycle configurat...

  5. Produced water irrigation changes the soil mesofauna community in a semiarid agroecosystem.

    Science.gov (United States)

    Ferreira, Raimundo Nonato Costa; Weber, Olmar Baller; Crisóstomo, Lindbergue Araujo

    2015-08-01

    The scarcity of water in semiarid regions requires alternative sources for irrigation to improve agricultural production. Here, we aimed to evaluate the effects of produced water from oil exploration on the structure of soil mesofauna during the dry and rainy seasons in irrigated sunflower and castor bean fields in a Brazilian semiarid region. Three irrigation treatments were applied on plots cultivated with castor beans and sunflowers: produced water treated by filtration (filtrated) or treated by reverse osmosis (reverse osmosis) and groundwater. The mesofauna under the biofuel crops was collected and identified during the dry and rainy seasons. Although the abundance and richness of the total fauna did not differ between seasons in sunflower plots, the community was altered. In castor beans, the abundance, richness, and community of mesofauna observed in plots irrigated with produced water differed from the groundwater treatment. Irrigation with produced water promotes important changes in soil fauna community that justify their assessment for the maintenance and monitoring of agroecosystems.

  6. Desalination and reuse of high-salinity shale gas produced water: drivers, technologies, and future directions.

    Science.gov (United States)

    Shaffer, Devin L; Arias Chavez, Laura H; Ben-Sasson, Moshe; Romero-Vargas Castrillón, Santiago; Yip, Ngai Yin; Elimelech, Menachem

    2013-09-03

    In the rapidly developing shale gas industry, managing produced water is a major challenge for maintaining the profitability of shale gas extraction while protecting public health and the environment. We review the current state of practice for produced water management across the United States and discuss the interrelated regulatory, infrastructure, and economic drivers for produced water reuse. Within this framework, we examine the Marcellus shale play, a region in the eastern United States where produced water is currently reused without desalination. In the Marcellus region, and in other shale plays worldwide with similar constraints, contraction of current reuse opportunities within the shale gas industry and growing restrictions on produced water disposal will provide strong incentives for produced water desalination for reuse outside the industry. The most challenging scenarios for the selection of desalination for reuse over other management strategies will be those involving high-salinity produced water, which must be desalinated with thermal separation processes. We explore desalination technologies for treatment of high-salinity shale gas produced water, and we critically review mechanical vapor compression (MVC), membrane distillation (MD), and forward osmosis (FO) as the technologies best suited for desalination of high-salinity produced water for reuse outside the shale gas industry. The advantages and challenges of applying MVC, MD, and FO technologies to produced water desalination are discussed, and directions for future research and development are identified. We find that desalination for reuse of produced water is technically feasible and can be economically relevant. However, because produced water management is primarily an economic decision, expanding desalination for reuse is dependent on process and material improvements to reduce capital and operating costs.

  7. Application of carbon isotopes to detect seepage out of coalbed natural gas produced water impoundments

    International Nuclear Information System (INIS)

    Sharma, Shikha; Baggett, Joshua K.

    2011-01-01

    Highlights: → Coalbed natural gas extraction results in large amount of produced water. → Risk of deterioration of ambient water quality. → Carbon isotope natural tracer for detecting seepage from produced water impoundments. - Abstract: Coalbed natural gas (CBNG) production from coal bed aquifers requires large volumes of produced water to be pumped from the subsurface. The produced water ranges from high quality that meets state and federal drinking water standards to low quality due to increased salinity and/or sodicity. The Powder River Basin of northeastern Wyoming is a major coalbed natural gas producing region, where water quality generally decreases moving from the southeastern portion of the basin towards the center. Most produced water in Wyoming is disposed into impoundments and other surface drainages, where it may infiltrate into shallow groundwater. Groundwater degradation caused by infiltration of CBNG produced water holding impoundments into arid, soluble salt-rich soils is an issue of immense importance because groundwater is a major source for stock water, irrigation, and drinking water for many small communities in these areas. This study examines the potential of using stable C isotope signatures of dissolved inorganic C (δ 13 C DIC ) to track the fate of CBNG produced water after it is discharged into the impoundments. Other geochemical proxies like the major cations and major anions were used in conjunction with field water quality measurements to understand the geochemical differences between CBNG produced waters and ambient waters in the study area. Samples were collected from the CBNG discharge outfalls, produced water holding impoundments, and monitoring wells from different parts of the Powder River Basin and analyzed for δ 13 C DIC . The CBNG produced waters from outfalls and impoundments have positive δ 13 C DIC values that fall within the range of +12 per mille to +22 per mille, distinct from the ambient regional surface and

  8. Investigation of the potential influence of production treatment chemicals on produced water toxicity

    International Nuclear Information System (INIS)

    Stine, E.R.; Gala, W.R.; Henry, L.R.

    1993-01-01

    Production treatment chemicals represent a diverse collection of chemical classes, added at various points from the wellhead to the final flotation cell, to prevent operational upsets and enhance the separation of oil from water. Information in the literature indicates that while many treatment chemicals are thought to partition into oil and not into the produced water, there are cases where a sufficiently water soluble treatment chemical is added at high enough concentrations to suggest that the treatment chemical may add to the aquatic toxicity of the produced water. A study was conducted to evaluate the potential effect of production treatment chemicals on the toxicity of produced waters using the US EPA Seven-day Mysidopsis bahia Survival, Growth and Fecundity Test. Samples of produced water were collected and tested for toxicity from three platforms under normal operating conditions, followed by repeated sampling and testing after a 72-hour period in which treatment chemical usage was discontinued, to the degree possible. Significant reductions in produced water toxicity were observed for two of the three platforms tested following either cessation of treatment chemical usage, or by comparing the toxicity of samples collected upstream and downstream of the point of treatment chemical addition

  9. Microbial community changes in hydraulic fracturing fluids and produced water from shale gas extraction.

    Science.gov (United States)

    Murali Mohan, Arvind; Hartsock, Angela; Bibby, Kyle J; Hammack, Richard W; Vidic, Radisav D; Gregory, Kelvin B

    2013-11-19

    Microbial communities associated with produced water from hydraulic fracturing are not well understood, and their deleterious activity can lead to significant increases in production costs and adverse environmental impacts. In this study, we compared the microbial ecology in prefracturing fluids (fracturing source water and fracturing fluid) and produced water at multiple time points from a natural gas well in southwestern Pennsylvania using 16S rRNA gene-based clone libraries, pyrosequencing, and quantitative PCR. The majority of the bacterial community in prefracturing fluids constituted aerobic species affiliated with the class Alphaproteobacteria. However, their relative abundance decreased in produced water with an increase in halotolerant, anaerobic/facultative anaerobic species affiliated with the classes Clostridia, Bacilli, Gammaproteobacteria, Epsilonproteobacteria, Bacteroidia, and Fusobacteria. Produced water collected at the last time point (day 187) consisted almost entirely of sequences similar to Clostridia and showed a decrease in bacterial abundance by 3 orders of magnitude compared to the prefracturing fluids and produced water samplesfrom earlier time points. Geochemical analysis showed that produced water contained higher concentrations of salts and total radioactivity compared to prefracturing fluids. This study provides evidence of long-term subsurface selection of the microbial community introduced through hydraulic fracturing, which may include significant implications for disinfection as well as reuse of produced water in future fracturing operations.

  10. Evaluation of Subsurface Flow and Free-water Surface Wetlands Treating NPR-3 Produced Water - Year No. 1

    International Nuclear Information System (INIS)

    Myers, J. E.; Jackson, L. M.

    2001-01-01

    This paper is a summary of some of the activities conducted during the first year of a three-year cooperative research and development agreement (CRADA) between the Department of Energy (DOE) Rocky Mountain Oilfield Testing Center (RMOTC) and Texaco relating to the treatment of produced water by constructed wetlands. The first year of the CRADA is for design, construction and acclimation of the wetland pilot units. The second and third years of the CRADA are for tracking performance of pilot wetlands as the plant and microbial communities mature. A treatment wetland is a proven technology for the secondary and tertiary treatment of produced water, storm water and other wastewaters. Treatment wetlands are typically classified as either free-water surface (FWS) or subsurface flow (SSF). Both FWS and SSF wetlands work well when properly designed and operated. This paper presents a collection of kinetic data gathered from pilot units fed a slipstream of Wyoming (NPR-3) produced water. The pilot units are set up outdoors to test climatic influences on treatment. Monitoring parameters include evapotranspiration, plant growth, temperature, and NPDES discharge limits. The pilot wetlands (FWS and SSF) consist of a series of 100-gal plastic tubs filled with local soils, gravel, sharp sand and native wetland plants (cattail (Typha spp.), bulrush (Scirpus spp.), dwarf spikerush (Eleocharis)). Feed pumps control hydraulic retention time (HRT) and simple water control structures control the depth of water. The treated water is returned to the existing produced water treatment system. All NPDES discharge limits are met. Observations are included on training RMOTC summer students to do environmental work

  11. The origin and fate of arsenic in coalbed natural gas-produced water ponds.

    Science.gov (United States)

    Sowder, J T; Kelleners, T J; Reddy, K J

    2010-01-01

    Coalbed natural gas (CBNG)-produced water contains small amounts of trace metals that can accumulate over time in produced water retention ponds. Within the Powder River Basin (PRB) of Wyoming, high concentrations of trace metals in pond water and their effect on shallow groundwater are potential concerns. A pond with a maximum As concentration of 146 microg L(-1) was studied in detail to determine the potential for groundwater pollution and to explain the cause for the high concentration of As. Infiltration characteristics, subsurface hydrology, our fall and pond water quality, isotope signatures, and trace metal balances were examined to assess the hydrology and geochemistry of the pond. The results indicated minimum or no infiltration of pond water and no measurable contamination of the shallow groundwater. The high As concentrations in the pond were determined to be the result of semi-continuous inputs of CBNG-produced water with low As concentrations (0.20-0.48 microg L(-1)), exasperated by low pond volumes during drought conditions. Because of reduced infiltration and high evaporation rates, As became concentrated over time. Reduced infiltration was most likely caused by the high sodium concentration and high sodium adsorption ratio of the CBNG-produced water, which disrupt soil structure. The findings for the pond and the techniques used may serve as a template for future impact assessments of other CBNG-produced water ponds and are relevant for the approximately 4000 ponds currently permitted in the PRB and for future ponds. Further studies are recommended in the use of playa landforms to store marginal-quality produced water.

  12. Polyoxadiazole hollow fibers for produced water treatment by direct contact membrane distillation

    KAUST Repository

    Xu, Jingli

    2018-01-08

    Treatment of produced water in the petroleum industry has been a challenge worldwide. In this study, we evaluated the use of direct contact membrane distillation (DCMD) for this purpose, removing oil and dissolved elements and supplying clean water from waste. We synthesized fluorinated polyoxadiazole, a highly hydrophobic polymer, to fabricate hollow fiber membranes, which were optimized and tested for simulated produced water and real produced water treatment. The process performance was investigated under different operating parameters, such as feed temperature, feed flow velocity and length of the membrane module for 4 days. The results indicate that by increasing feed temperature and feed flow rate the vapor flux increases. The flux decreased with increasing the length of the module due to the decrease of the driving force along the module. The fouling behavior, which corresponds to flux decline and cleaning efficiency of the membrane, was studied. The performance of the fabricated hollow fiber membranes was demonstrated for the treatment of produced water, complying with the industrial reuse and discharge limits.

  13. Decentralised water and wastewater treatment technologies to produce functional water for irrigation

    DEFF Research Database (Denmark)

    Battilani, Adriano; Steiner, Michele; Andersen, Martin

    2010-01-01

    The EU project SAFIR aimed to help farmers solve problems related to the use of low quality water for irrigation in a context of increasing scarcity of conventional freshwater resources. New decentralised water treatment devices (prototypes) were developed to allow a safe direct or indirect reuse...... of wastewater produced by small communities/industries or the use of polluted surface water. Water treatment technologies were coupled with irrigation strategies and technologies to obtain a flexible, easy to use, integrated management of the system. The challenge is to apply new strategies and technologies...... which allow using the lowest irrigation water quality without harming food safety or yield and fruit or derivatives quality. This study presents the results of prototype testing of a small-scale compact pressurized membrane bioreactor and of a modular field treatment system including commercial gravel...

  14. Treatment of Produced Waters Using a Surfactant Modified Zeolite/Vapor Phase Bioreactor System

    Energy Technology Data Exchange (ETDEWEB)

    Lynn E. Katz; Kerry A. Kinney; R. S. Bowman; E. J. Sullivan

    2004-03-11

    This report summarizes work of this project from October 2003 through March 2004. The major focus of the research was to further investigate BTEX removal from produced water, to quantify metal ion removal from produced water, and to evaluate a lab-scale vapor phase bioreactor (VPB) for BTEX destruction in off-gases produced during SMZ regeneration. Batch equilibrium sorption studies were conducted to evaluate the effect of semi-volatile organic compounds commonly found in produced water on the sorption of benzene, toluene, ethylbenzene, and xylene (BTEX) onto surfactant-modified zeolite (SMZ) and to examine selected metal ion sorption onto SMZ. The sorption of polar semi-volatile organic compounds and metals commonly found in produced water onto SMZ was also investigated. Batch experiments were performed in a synthetic saline solution that mimicked water from a produced water collection facility in Wyoming. Results indicated that increasing concentrations of semi-volatile organic compounds increased BTEX sorption. The sorption of phenol compounds could be described by linear isotherms, but the linear partitioning coefficients decreased with increasing pH, especially above the pKa's of the compounds. Linear correlations relating partitioning coefficients of phenol compounds with their respective solubilities and octanol-water partitioning coefficients were developed for data collected at pH 7.2. The sorption of chromate, selenate, and barium in synthetic produced water were also described by Langmuir isotherms. Experiments conducted with a lab-scale vapor phase bioreactor (VPB) packed with foam indicated that this system could achieve high BTEX removal efficiencies once the nutrient delivery system was optimized. The xylene isomers and benzene were found to require the greatest biofilter bed depth for removal. This result suggested that these VOCs would ultimately control the size of the biofilter required for the produced water application. The biofilter

  15. OPTIMIZATION OF PRODUCED WATER TREATMENT PROCESS - A CASE STUDY FOR DISPOSAL IN THE NIGER DELTA

    Directory of Open Access Journals (Sweden)

    BONIFACE A. ORIJI

    2017-12-01

    Full Text Available Produced water is the interstitial reservoir water that flows to the surface with the crude oil into the production separators. This study addressed the effects of some chemicals on produced water and the challenges of finding the optimal concentrations of these chemicals for treating produced water. In this study, produced water treatment was carried out in an oil production platform located in the Niger Delta so as to determine the effect of a particular scale inhibitor, biocide, demulsifier and water clarifier, also to obtain the optimum concentrations of these chemicals in the treatment of produced water. The physico-chemical properties and microbial content of the produced water were determined. The results showed that the conductivity, hardness, pH and alkalinity reduced with increasing concentration of the scale inhibitor. The total heterotrophic bacteria count (THBC, heterotrophic fungi count (THFC and the Sulphate reducing bacteria count (SRBC were found to reduce with increasing concentration of biocide and exposure time. The increase in biocide concentration from 64 PPM to 100 PPM resulted in the reduction of THBC by 99.78%, THFC by 81.32% and SRBC 99.85%. The water clarifier gave the optimum concentration for oil and grease in the produced water at 7.3 PPM.

  16. Coalbed methane-produced water quality and its management options in Raniganj Basin, West Bengal, India

    Science.gov (United States)

    Mendhe, Vinod Atmaram; Mishra, Subhashree; Varma, Atul Kumar; Singh, Awanindra Pratap

    2017-06-01

    Coalbed methane (CBM) recovery is associated with production of large quantity of groundwater. The coal seams are depressurized by pumping of water for regular and consistent gas production. Usually, CBM operators need to pump >10 m3 of water per day from one well, which depends on the aquifer characteristics, drainage and recharge pattern. In India, 32 CBM blocks have been awarded for exploration and production, out of which six blocks are commercially producing methane gas at 0.5 million metric standard cubic feet per day. Large amount of water is being produced from CBM producing blocks, but no specific information or data are available for geochemical properties of CBM-produced water and its suitable disposal or utilization options for better management. CBM operators are in infancy and searching for the suitable solutions for optimal management of produced water. CBM- and mine-produced water needs to be handled considering its physical and geochemical assessment, because it may have environmental as well as long-term impact on aquifer. Investigations were carried out to evaluate geochemical and hydrogeological conditions of CBM blocks in Raniganj Basin. Totally, 15 water samples from CBM well head and nine water samples from mine disposal head were collected from Raniganj Basin. The chemical signature of produced water reveals high sodium and bicarbonate concentrations with low calcium and magnesium, and very low sulphate in CBM water. It is comprehend that CBM water is mainly of Na-HCO3 type and coal mine water is of Ca-Mg-SO4 and HCO3-Cl-SO4 type. The comparative studies are also carried out for CBM- and mine-produced water considering the geochemical properties, aquifer type, depth of occurrence and lithological formations. Suitable options like impounding, reverse osmosis, irrigation and industrial use after prerequisite treatments are suggested. However, use of this huge volume of CBM- and mine-produced water for irrigation or other beneficial purposes

  17. Sulfide stress corrosion study of a super martensitic stainless steel in H2S sour environments: Metallic sulfides formation and hydrogen embrittlement

    Science.gov (United States)

    Monnot, Martin; Nogueira, Ricardo P.; Roche, Virginie; Berthomé, Grégory; Chauveau, Eric; Estevez, Rafael; Mantel, Marc

    2017-02-01

    Thanks to their high corrosion resistance, super martensitic stainless steels are commonly used in the oil and gas industry, particularly in sour environments. Some grades are however susceptible to undergo hydrogen and mechanically-assisted corrosion processes in the presence of H2S, depending on the pH. The martensitic stainless steel EN 1.4418 grade exhibits a clear protective passive behavior with no sulfide stress corrosion cracking when exposed to sour environments of pH ≥ 4, but undergoes a steep decrease in its corrosion resistance at lower pH conditions. The present paper investigated this abrupt loss of corrosion resistance with electrochemical measurements as well as different physicochemical characterization techniques. Results indicated that below pH 4.0 the metal surface is covered by a thick (ca 40 μm) porous and defect-full sulfide-rich corrosion products layer shown to be straightforwardly related to the onset of hydrogen and sulfide mechanically-assisted corrosion phenomena.

  18. The functional potential of microbial communities in hydraulic fracturing source water and produced water from natural gas extraction characterized by metagenomic sequencing.

    Directory of Open Access Journals (Sweden)

    Arvind Murali Mohan

    Full Text Available Microbial activity in produced water from hydraulic fracturing operations can lead to undesired environmental impacts and increase gas production costs. However, the metabolic profile of these microbial communities is not well understood. Here, for the first time, we present results from a shotgun metagenome of microbial communities in both hydraulic fracturing source water and wastewater produced by hydraulic fracturing. Taxonomic analyses showed an increase in anaerobic/facultative anaerobic classes related to Clostridia, Gammaproteobacteria, Bacteroidia and Epsilonproteobacteria in produced water as compared to predominantly aerobic Alphaproteobacteria in the fracturing source water. The metabolic profile revealed a relative increase in genes responsible for carbohydrate metabolism, respiration, sporulation and dormancy, iron acquisition and metabolism, stress response and sulfur metabolism in the produced water samples. These results suggest that microbial communities in produced water have an increased genetic ability to handle stress, which has significant implications for produced water management, such as disinfection.

  19. Antifungal modes of action of Saccharomyces and other biocontrol yeasts against fungi isolated from sour and grey rots.

    Science.gov (United States)

    Nally, M C; Pesce, V M; Maturano, Y P; Rodriguez Assaf, L A; Toro, M E; Castellanos de Figueroa, L I; Vazquez, F

    2015-07-02

    The aim of this study was to determine the putative modes of action of 59 viticultural yeasts (31 Saccharomyces and 28 non-Saccharomyces) that inhibited fungi isolated from sour and grey rot in grapes. Inhibition of fungal mycelial growth by metabolites, enzyme activities (laminarinases, chitinases), antifungal volatiles, competition for nutrients (siderophores, Niche Overlap Index (NOI)), inhibition of fungal spore germination and decreased germinal tube length and induction of resistance were assayed. Biofungicide yeasts were classified into "antifungal patterns", according to their mechanisms of action. Thirty isolates presented at least two of the mechanisms assayed. We propose that inhibition of fungal mycelial growth by metabolites, laminarinases, competition for nutrients, inhibition of fungal spore germination and decreased germinal tube length, and antifungal volatiles by Saccharomyces and non-Saccharomyces viticultural yeasts is used as putative biocontrol mechanisms against phytopathogenic fungi. Twenty-four different antifungal patterns were identified. Siderophore production (N)and a combination of siderophore production and NOI>0.92 (M)were the most frequent antifungal patterns observed in the biofungicide yeasts assayed. Elucidation of these mechanisms could be useful for optimization of an inoculum formulation, resulting in a more consistent control of grey and sour rot with Saccharomyces and non-Saccharomyces biocontrol yeasts. Copyright © 2015 Elsevier B.V. All rights reserved.

  20. A cost-benefit analysis of produced water management opportunities in selected unconventional oil and gas plays

    Science.gov (United States)

    Marsters, P.; Macknick, J.; Bazilian, M.; Newmark, R. L.

    2013-12-01

    Unconventional oil and gas production in North America has grown enormously over the past decade. The combination of horizontal drilling and hydraulic fracturing has made production from shale and other unconventional resources economically attractive for oil and gas operators, but has also resulted in concerns over potential water use and pollution issues. Hydraulic fracturing operations must manage large volumes of water on both the front end as well as the back end of operations, as significant amounts of water are coproduced with hydrocarbons. This water--often called flowback or produced water--can contain chemicals from the hydraulic fracturing fluid, salts dissolved from the source rock, various minerals, volatile organic chemicals, and radioactive constituents, all of which pose potential management, safety, and public health issues. While the long-term effects of hydraulic fracturing on aquifers, drinking water supplies, and surface water resources are still being assessed, the immediate impacts of produced water on local infrastructure and water supplies are readily evident. Produced water management options are often limited to underground injection, disposal at centralized treatment facilities, or recycling for future hydraulic fracturing operations. The costs of treatment, transport, and recycling are heavily dependent on local regulations, existing infrastructure, and technologies utilized. Produced water treatment costs also change over time during energy production as the quality of the produced water often changes. To date there is no publicly available model that evaluates the cost tradeoffs associated with different produced water management techniques in different regions. This study addresses that gap by characterizing the volume, qualities, and temporal dynamics of produced water in several unconventional oil and gas plays; evaluating potential produced water management options, including reuse and recycling; and assessing how hydraulic

  1. Radionuclides in produced water from Norwegian oil and gas installations - concentrations and bioavailability

    International Nuclear Information System (INIS)

    Eriksen, D.Oe.; Sidhu, R.; Stralberg, E.; Iden, K.I.; Hylland, K.; Ruus, A.; Roeyset, O.; Berntssen, M.H.G.; Rye, H.

    2006-01-01

    Substantial amounts of produced water, containing elevated levels of radionuclides (mainly 226 Ra and 228 Ra) are discharged to the sea as a result of oil and gas production on the Norwegian Continental Shelf. So far no study has assessed the potential radiological effects on marine biota in connection with radionuclide discharges to the North Sea. The main objective of the project is to establish radiological safe discharge limits for radium, lead and polonium associated with other components in produced water from oil and gas installations on the Norwegian continental shelf. This study reports results indicating that the presence of added chemicals such as scale inhibitors in produced water has a marked influence on the formation of radium and barium sulphates when produced water is mixed with sea water. Thus, the mobility and bioavailability of radium (and barium) will be larger than anticipated. Also, the bioavailability of food-borne radium is shown to increase due to presence of such chemicals. (author)

  2. Ceramic membrane ozonator for soluble organics removal from produced water

    Science.gov (United States)

    Siagian, U. W. R.; Dwipramana, A. S.; Perwira, S. B.; Khoiruddin; Wenten, I. G.

    2018-01-01

    In this work, the performance of ozonation for degradation of soluble organic compounds in produced water was investigated. Tubular ceramic membrane diffuser (with and without a static mixer in the lumen side) was used to facilitate contact between ozone and produced water. The ozonation was conducted at ozone flow rate of 8 L.min-1, ozone concentration of 0.4 ppm, original pH of the solution, and pressure of 1.2 bar, while the flow rates of the produced water were varied (192, 378 and 830 mL.min-1). It was found that the reduction of benzene, toluene, ethylbenzene, and xylene were 85%, 99%, 85%, and 95%, respectively. A lower liquid flow rate in a laminar state showed a better component reduction due to the longer contacting time between the liquid and the gas phase. The introduction of the static mixer in the lumen side of the membrane as a turbulence promoter provided a positive effect on the performance of the membrane diffuser. The twisted static mixer exhibited the better removal rate than the spiral static mixer.

  3. Have Norwegian producers of hydroelectric power wasted the water?

    International Nuclear Information System (INIS)

    2003-01-01

    Norwegian producers of hydroelectric power have been criticized for having exported power to Sweden during the autumn and winter 2003/2004. As this analysis shows, although the reservoir level in Norway was below normal in October already, the negative deviation from the normal reservoir level was even greater in Sweden till the end of the year. Also when the magnitude of the reserve is measured relative to the number of weeks with normal winter production for which it lasts, the situation was worse in Sweden than in Norway. After New Year the deviation from the normal reservoir level has been much the same in the two countries and has changed in parallel. During this period the exchange between the two countries has approximately balanced and the power flow from Sweden to Norway has grown gradually. With this as a background, there is no basis for asserting that the Norwegian producers have managed the water resources in an irresponsible way. In general, the power flow and the water resource management in the two countries appear reasonable considering the water influx and the prices. Different market imperfections may nevertheless have rendered the water resource management socially less then optimal.

  4. Performance Evaluation of Produced Water Quality from a ...

    African Journals Online (AJOL)

    Michael Horsfall

    1Department of Chemical Engineering, Federal University of Technology, Owerri, Nigeria, ... ABSTRACT: Produced water, which is a mixture of organic and inorganic compounds, is a major waste ... from one viewpoint, an approach to reducing adverse environmental ... pipette onto a glass-fiber filter with applied vacuum.

  5. Investigations of corrosion films formed on API-X52 pipeline steel in acid sour media

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez-Espejel, A. [Instituto Politecnico Nacional, Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico); Dominguez-Crespo, M.A. [Instituto Politecnico Nacional, CICATA-Unidad Altamira-Tamaulipas, km 14.5, Carretera Tampico-Puerto Industrial Altamira, 89600 Altamira, Tamps (Mexico); Cabrera-Sierra, R. [Instituto Politecnico Nacional, Departamento de Ingenieria Quimica Industrial, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico); Rodriguez-Meneses, C. [Instituto Politecnico Nacional, Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico); Arce-Estrada, E.M., E-mail: earce@ipn.m [Instituto Politecnico Nacional, Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico)

    2010-07-15

    Corrosion films formed by voltammetry using different switching potentials and by immersion on API-X52 pipeline steel in simulated acid sour media (NACE ID182) have been characterized using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Linear Polarization and Electrochemical Impedance Spectroscopy (EIS) techniques. XRD and EDS analysis showed that the films are mainly composed of sulphide compounds (mackinawite, troilite, marcasite and pyrite) as well as iron oxides, as steel damage increases. Across SEM micrographs the corrosion films formed by potentiodynamic and immersion tests are very similar, covering most of the steel. Polarization and EIS results corroborate poor behavior against corrosion.

  6. Investigations of corrosion films formed on API-X52 pipeline steel in acid sour media

    International Nuclear Information System (INIS)

    Hernandez-Espejel, A.; Dominguez-Crespo, M.A.; Cabrera-Sierra, R.; Rodriguez-Meneses, C.; Arce-Estrada, E.M.

    2010-01-01

    Corrosion films formed by voltammetry using different switching potentials and by immersion on API-X52 pipeline steel in simulated acid sour media (NACE ID182) have been characterized using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Linear Polarization and Electrochemical Impedance Spectroscopy (EIS) techniques. XRD and EDS analysis showed that the films are mainly composed of sulphide compounds (mackinawite, troilite, marcasite and pyrite) as well as iron oxides, as steel damage increases. Across SEM micrographs the corrosion films formed by potentiodynamic and immersion tests are very similar, covering most of the steel. Polarization and EIS results corroborate poor behavior against corrosion.

  7. Produced water management - clean and safe oil and gas production

    International Nuclear Information System (INIS)

    2006-01-01

    The conference contains 22 presentations on topics within pollution sources and abatement, discharge reductions, water analysis and monitoring, water production, treatment and injection, enhanced recovery, condensate water, produced water markets, separation technologies for oil/gas/condensate and water, oil removal from solids, environmental risks of oil and gas production and environmental impacts on ecosystems and fisheries. Some oil field case histories are presented. The main focus is on the northern areas such as the North Sea, the north Atlantic Ocean and the Barents Sea, and technological aspects (tk)

  8. Produced water management - clean and safe oil and gas production

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The conference contains 22 presentations on topics within pollution sources and abatement, discharge reductions, water analysis and monitoring, water production, treatment and injection, enhanced recovery, condensate water, produced water markets, separation technologies for oil/gas/condensate and water, oil removal from solids, environmental risks of oil and gas production and environmental impacts on ecosystems and fisheries. Some oil field case histories are presented. The main focus is on the northern areas such as the North Sea, the north Atlantic Ocean and the Barents Sea, and technological aspects (tk)

  9. Bounding the marginal cost of producing potable water including the use of seawater desalinization as a backstop potable water production technology

    Energy Technology Data Exchange (ETDEWEB)

    Dooley, James J.

    2014-04-01

    The analysis presented in this technical report should allow for the creation of high, medium, and low cost potable water prices for GCAM. Seawater reverse osmosis (SWRO) based desalinization should act as a backstop for the cost of producing potable water (i.e., the literature seems clear that SWRO should establish an upper bound for the plant gate cost of producing potable water). Transporting water over significant distances and having to lift water to higher elevations to reach end-users can also have a significant impact on the cost of producing water. The three potable fresh water scenarios describe in this technical report are: low cost water scenario ($0.10/m3); medium water cost scenario ($1.00/m3); and high water cost scenario ($2.50/m3).

  10. Advanced Heterogeneous Fenton Treatment of Coalbed Methane-Produced Water Containing Fracturing Fluid

    Directory of Open Access Journals (Sweden)

    Meng Zhang

    2018-04-01

    Full Text Available This study investigated the heterogeneous Fenton treatment to process coalbed methane-produced water containing fracturing fluid and chose the development region of coalbed methane in the Southern Qinshui Basin as a research area. We synthesized the catalyst of Fe-Co/γ-Al2O3 by homogeneous precipitation method and characterized it by BET, XRD, SEM-EDS, FTIR, and XPS. Based on the degradation rate, we studied the influences of the heterogeneous Fenton method on the coalbed methane output water treatment process parameters, including initial pH, H2O2 concentration, and the catalyst concentration. We also investigated the impacts of overall reaction kinetics of heterogeneous catalytic oxidation on coalbed methane-produced water containing fracturing fluid. Results showed that Fe-Co/γ-Al2O3 as a Fenton catalyst has a good catalytic oxidation effect and can effectively process coalbed methane-produced water. This reaction also followed first-order kinetics. The optimal conditions were as follows: the initial pH of 3.5, a H2O2 concentration of 40 mol L−1, a catalyst concentration of 4 g/L, and an apparent reaction rate constant of 0.0172 min−1. Our results provided a basis to establish methods for treating coalbed methane-produced water.

  11. Recovery of Fresh Water Resources from Desalination of Brine Produced During Oil and Gas Production Operations

    Energy Technology Data Exchange (ETDEWEB)

    David B. Burnett; Mustafa Siddiqui

    2006-12-29

    Management and disposal of produced water is one of the most important problems associated with oil and gas (O&G) production. O&G production operations generate large volumes of brine water along with the petroleum resource. Currently, produced water is treated as a waste and is not available for any beneficial purposes for the communities where oil and gas is produced. Produced water contains different contaminants that must be removed before it can be used for any beneficial surface applications. Arid areas like west Texas produce large amount of oil, but, at the same time, have a shortage of potable water. A multidisciplinary team headed by researchers from Texas A&M University has spent more than six years is developing advanced membrane filtration processes for treating oil field produced brines The government-industry cooperative joint venture has been managed by the Global Petroleum Research Institute (GPRI). The goal of the project has been to demonstrate that treatment of oil field waste water for re-use will reduce water handling costs by 50% or greater. Our work has included (1) integrating advanced materials into existing prototype units and (2) operating short and long-term field testing with full size process trains. Testing at A&M has allowed us to upgrade our existing units with improved pre-treatment oil removal techniques and new oil tolerant RO membranes. We have also been able to perform extended testing in 'field laboratories' to gather much needed extended run time data on filter salt rejection efficiency and plugging characteristics of the process train. The Program Report describes work to evaluate the technical and economical feasibility of treating produced water with a combination of different separation processes to obtain water of agricultural water quality standards. Experiments were done for the pretreatment of produced water using a new liquid-liquid centrifuge, organoclay and microfiltration and ultrafiltration membranes

  12. Modeling Approach for Estimating Co-Produced Water Volumes and Saltwater Disposal Volumes in Oklahoma

    Science.gov (United States)

    Murray, K. E.

    2016-12-01

    Management of produced fluids has become an important issue in Oklahoma because large volumes of saltwater are co-produced with oil and gas, and disposed into saltwater disposal wells at high rates. Petroleum production increased from 2009-2015, especially in central and north-central Oklahoma where the Mississippian and Hunton zones were redeveloped using horizontal wells and dewatering techniques that have led to a disproportional increase in produced water volumes. Improved management of co-produced water, including desalination for beneficial reuse and decreased saltwater disposal volumes, is only possible if spatial and temporal trends can be defined and related to the producing zones. It is challenging to quantify the volumes of co-produced water by region or production zone because co-produced water volumes are generally not reported. Therefore, the goal of this research is to estimate co-produced water volumes for 2008-present with an approach that can be replicated as petroleum production shifts to other regions. Oil and gas production rates from subsurface zones were multiplied by ratios of H2O:oil and H2O:gas for the respective zones. Initial H2O:oil and H2O:gas ratios were adjusted/calibrated, by zone, to maximize correlation of county-scale produced H2O estimates versus saltwater disposal volumes from 2013-2015. These calibrated ratios were then used to compute saltwater disposal volumes from 2008-2012 because of apparent data gaps in reported saltwater disposal volumes during that timeframe. This research can be used to identify regions that have the greatest need for produced water treatment systems. The next step in management of produced fluids is to explore optimal energy-efficient strategies that reduce deleterious effects.

  13. Community inflamed: Passionate opposition mounted to sour-gas drilling plan upwind of Canada's energy capital

    International Nuclear Information System (INIS)

    Lorenz, A.

    1998-01-01

    Residents of Bearspaw and Glendale, two small communities near Calgary are up in arms in opposition to the plans of Canadian 88 Energy Company to drill a 'level four' sour gas well in the area. The target gas contains 33.9 per cent hydrogen sulfide, a substance rated as lethal in much lower doses. Since the well is slated to be drilled on high ground upwind of Calgary, an accident causing a leak could expose community residents and thousands of Calgarians within half hour distance from the well to hydrogen sulfide concentrations several times higher than the Alberta Energy Board considers safe. Seepage into the water system poses yet another danger. For reasons that are not too well understood the Alberta Energy Board relaxed the size of the area for which the company must provide an emergency response plan from a radius of 18 km to a radius of 4 km, considered by experts to be totally unacceptable in a populated area. The Board granted the relaxation of the area covered by the emergency response plan on the assurances of the Company that it would substantially increase the criteria needed to make the plan manageable. However, the community is not convinced that the emergency response plan comes near to addressing the problem, and is prepared to oppose drilling of the well by all available means

  14. Influence of softening sequencing on electrocoagulation treatment of produced water.

    Science.gov (United States)

    Esmaeilirad, Nasim; Carlson, Ken; Omur Ozbek, Pinar

    2015-01-01

    Electrocoagulation has been used to remove solids and some metals from both water and wastewater sources for decades. Additionally, chemical softening is commonly employed in water treatment systems to remove hardness. This paper assesses the combination and sequence of softening and EC methods to treat hydraulic fracturing flowback and produced water from shale oil and gas operations. EC is one of the available technologies to treat produced water for reuse in frac fluids, eliminating not only the need to transport more water but also the costs of providing fresh water. In this paper, the influence of chemical softening on EC was studied. In the softening process, pH was raised to 9.5 and 10.2 before and after EC, respectively. Softening, when practiced before EC was more effective for removing turbidity with samples from wells older than one month (99% versus 88%). However, neither method was successful in treating samples collected from early flowback (1-day and 2-day samples), likely due to the high concentration of organic matter. For total organic carbon, hardness, Ba, Sr, and B removal, application of softening before EC appeared to be the most efficient approach, likely due to the formation of solids before the coagulation process. Copyright © 2014 Elsevier B.V. All rights reserved.

  15. [Actinobacteria and their odor-producing capacities in a surface water in Shanghai].

    Science.gov (United States)

    Chen, Jiao; Bai, Xiao-hui; Lu, Ning; Wang, Xian-yun; Zhang, Yong-hui; Wu, Pan-cheng; Guo, Xin-chi

    2014-10-01

    The odor in raw water is one of the main sources of odor in drinking water. The occurrence of actinobacteria and their odor producing capacities in a reservoir in.Shanghai were investigated. Gauze's medium and membrane filtration were used for actinobacteria isolation. Through combined methods of 16S rRNA sequencing, colony and hyphae morphology, carbon source utilization, physiological and biochemical characteristics, 40 strains of actinobacteria were identified from the reservoir. Results showed that there were 38 Streptomyces, an Aeromicrobium and a Pseudonocardia. Liquid culture medium and the real reservoir water were used to test the odor producing capacity of these 40 strains of actinobacteria, and headspace solid phase microextraction (HS-SPME) and high resolution gas chromatography mass spectroscopy (GC/MS) were used to analyze the odor compounds 2-methylisoborneol (2-MIB) and geosmin (GSM) in the fermentation liquor. The test results showed that, the odor-producing capacities of these actinobacteria in different fermentation media showed different variation trends, even within the genera Streptomyces. The odor-producing capacity of actinobacteria in the liquid culture medium could not represent their states in the reservoir water or their actual odor contribution to the aquatic environment.

  16. Treatment of Produced Water Using a Surfactant Modified Zeolite/Vapor Phase Bioreactor System

    Energy Technology Data Exchange (ETDEWEB)

    Lynn E. Katz; Kerry A. Kinney; Robert S. Bowman; Enid J. Sullivan; Soondong Kwon; Elaine B. Darby; Li-Jung Chen; Craig R. Altare

    2006-01-31

    Co-produced water from the oil and gas industry accounts for a significant waste stream in the United States. Produced waters typically contain a high total dissolved solids content, dissolved organic constituents such as benzene and toluene, an oil and grease component as well as chemicals added during the oil-production process. It has been estimated that a total of 14 billion barrels of produced water were generated in 2002 from onshore operations (Veil, 2004). Although much of this produced water is disposed via reinjection, environmental and cost considerations can make surface discharge of this water a more practical means of disposal. In addition, reinjection is not always a feasible option because of geographic, economic, or regulatory considerations. In these situations, it may be desirable, and often necessary from a regulatory viewpoint, to treat produced water before discharge. It may also be feasible to treat waters that slightly exceed regulatory limits for re-use in arid or drought-prone areas, rather than losing them to reinjection. A previous project conducted under DOE Contract DE-AC26-99BC15221 demonstrated that surfactant modified zeolite (SMZ) represents a potential treatment technology for produced water containing BTEX. Laboratory and field experiments suggest that: (1) sorption of benzene, toluene, ethylbenzene and xylenes (BTEX) to SMZ follows linear isotherms in which sorption increases with increasing solute hydrophobicity; (2) the presence of high salt concentrations substantially increases the capacity of the SMZ for BTEX; (3) competitive sorption among the BTEX compounds is negligible; and, (4) complete recovery of the SMZ sorption capacity for BTEX can be achieved by air sparging the SMZ. This report summarizes research for a follow on project to optimize the regeneration process for multiple sorption/regeneration cycles, and to develop and incorporate a vapor phase bioreactor (VPB) system for treatment of the off-gas generated during

  17. Use of Produced Water in Recirculated Cooling Systems at Power Generating Facilities

    Energy Technology Data Exchange (ETDEWEB)

    C. McGowin; M. DiFilippo; L. Weintraub

    2006-06-30

    Tree ring studies indicate that, for the greater part of the last three decades, New Mexico has been relatively 'wet' compared to the long-term historical norm. However, during the last several years, New Mexico has experienced a severe drought. Some researchers are predicting a return of very dry weather over the next 30 to 40 years. Concern over the drought has spurred interest in evaluating the use of otherwise unusable saline waters to supplement current fresh water supplies for power plant operation and cooling and other uses. The U.S. Department of Energy's National Energy Technology Laboratory sponsored three related assessments of water supplies in the San Juan Basin area of the four-corner intersection of Utah, Colorado, Arizona, and New Mexico. These were (1) an assessment of using water produced with oil and gas as a supplemental supply for the San Juan Generating Station (SJGS); (2) a field evaluation of the wet-surface air cooling (WSAC) system at SJGS; and (3) the development of a ZeroNet systems analysis module and an application of the Watershed Risk Management Framework (WARMF) to evaluate a range of water shortage management plans. The study of the possible use of produced water at SJGS showed that produce water must be treated to justify its use in any reasonable quantity at SJGS. The study identified produced water volume and quality, the infrastructure needed to deliver it to SJGS, treatment requirements, and delivery and treatment economics. A number of produced water treatment alternatives that use off-the-shelf technology were evaluated along with the equipment needed for water treatment at SJGS. Wet surface air-cooling (WSAC) technology was tested at the San Juan Generating Station (SJGS) to determine its capacity to cool power plant circulating water using degraded water. WSAC is a commercial cooling technology and has been used for many years to cool and/or condense process fluids. The purpose of the pilot test was to

  18. Field Validation of Toxicity Tests to Evaluate the Potential for Beneficial Use of Produced Water

    Energy Technology Data Exchange (ETDEWEB)

    Joseph Bidwell; Jonathan Fisher; Naomi Cooper

    2008-03-31

    This study investigated potential biological effects of produced water contamination derived from occasional surface overflow and possible subsurface intrusion at an oil production site along the shore of Skiatook Lake, Oklahoma. We monitored basic chemistry and acute toxicity to a suite of standard aquatic test species (fathead minnow-Pimephales promelas, Daphnia pulex, Daphnia magna, and Ceriodaphnia dubia) in produced water and in samples taken from shallow groundwater wells on the site. Toxicity identification evaluations and ion toxicity modeling were used to identify toxic constituents in the samples. Lake sediment at the oil production site and at a reference site were also analyzed for brine intrusion chemically and by testing sediment toxicity using the benthic invertebrates, Chironomus dilutus, and Hyallela azteca. Sediment quality was also assessed with in situ survival and growth studies with H. azteca and the Asian clam, Corbicula fluminea, and by benthic macroinvertebrate community sampling. The produced water was acutely toxic to the aquatic test organisms at concentrations ranging from 1% to 10% of the whole produced water sample. Toxicity identification evaluation and ion toxicity modeling indicated major ion salts and hydrocarbons were the primary mixture toxicants. The standardized test species used in the laboratory bioassays exhibited differences in sensitivity to these two general classes of contaminants, which underscores the importance of using multiple species when evaluating produced water toxicity. Toxicity of groundwater was greater in samples from wells near a produced water injection well and an evaporation pond. Principle component analyses (PCA) of chemical data derived from the groundwater wells indicated dilution by lake water and possible biogeochemical reactions as factors that ameliorated groundwater toxicity. Elevated concentrations of major ions were found in pore water from lake sediments, but toxicity from these ions was

  19. Organic substances in produced and formation water from unconventional natural gas extraction in coal and shale

    Science.gov (United States)

    Orem, William H.; Tatu, Calin A.; Varonka, Matthew S.; Lerch, Harry E.; Bates, Anne L.; Engle, Mark A.; Crosby, Lynn M.; McIntosh, Jennifer

    2014-01-01

    Organic substances in produced and formation water from coalbed methane (CBM) and gas shale plays from across the USA were examined in this study. Disposal of produced waters from gas extraction in coal and shale is an important environmental issue because of the large volumes of water involved and the variable quality of this water. Organic substances in produced water may be environmentally relevant as pollutants, but have been little studied. Results from five CBM plays and two gas shale plays (including the Marcellus Shale) show a myriad of organic chemicals present in the produced and formation water. Organic compound classes present in produced and formation water in CBM plays include: polycyclic aromatic hydrocarbons (PAHs), heterocyclic compounds, alkyl phenols, aromatic amines, alkyl aromatics (alkyl benzenes, alkyl biphenyls), long-chain fatty acids, and aliphatic hydrocarbons. Concentrations of individual compounds range from gas shale unimpacted by production chemicals have a similar range of compound classes as CBM produced water, and TOC levels of about 8 mg/L. However, produced water from the Marcellus Shale using hydraulic fracturing has TOC levels as high as 5500 mg/L and a range of added organic chemicals including, solvents, biocides, scale inhibitors, and other organic chemicals at levels of 1000 s of μg/L for individual compounds. Levels of these hydraulic fracturing chemicals and TOC decrease rapidly over the first 20 days of water recovery and some level of residual organic contaminants remain up to 250 days after hydraulic fracturing. Although the environmental impacts of the organics in produced water are not well defined, results suggest that care should be exercised in the disposal and release of produced waters containing these organic substances into the environment because of the potential toxicity of many of these substances.

  20. Effects of Ultrasound Assistance on Dehydration Processes and Bioactive Component Retention of Osmo-Dried Sour Cherries.

    Science.gov (United States)

    Siucińska, Karolina; Mieszczakowska-Frąc, Monika; Połubok, Aleksandra; Konopacka, Dorota

    2016-07-01

    Despite having numerous health benefits, dried sour cherries have proven to be more acceptable to consumers when infused with sugar or other sweeteners to enhance their flavor, which, in turn, leads to serious anthocyanin losses. For this reason, a consideration was made for the application of ultrasound to accelerate solid gain and shorten drying time, thus favoring bioactive component retention. To determine the usefulness of ultrasound as a tool for sour cherry osmotic infusion enhancement, the effect of sonication time on dehydration effectiveness, as well as the stability of bioactive components during osmotic treatment and consecutive convective drying, was investigated. Fruits were osmo-dehydrated using a 60% sucrose solution for 120 min (40 °C), during which, ultrasound of 25 kHz (0.4 W/cm(2) ), was applied for 0, 30, 60, 90, and 120 min, after which, the fruits were convectively dried. In the range of the applied ultrasound energy no significant effect of sonication on mass transfer intensification was observed; moreover, longer acoustic treatment seemed to retard moisture removal during subsequent convective drying, which can be related to the breakdown of the parenchyma cell walls caused by the prolonged ultrasound (US) action. It was concluded that although US assistance could be considered neutral for bioactive component retention, excessive sonication time can lead to some anthocyanin deterioration. According to high-performance liquid chromatography analysis, the particular anthocyanin alterations, both during dehydration and final drying, occurred in a similar way. Sonication time prolongation caused approximately 10% more bioactive compound deterioration, than earlier, shorter trials. © 2016 Institute of Food Technologists®

  1. 1000 tones of heavy water produced at ROMAG PROD, Drobeta-Turnu Severin

    International Nuclear Information System (INIS)

    2001-01-01

    On May 25, 2001 the heavy water plant ROMAG PROD at Drobeta-Turnu Severin recorded the production of the 1000-th tone of nuclear purity heavy water. The heavy water plant ROMAG PROD makes use of a technology based on the results of isotopic deuterium separation research carried out at the Research and Design Institutes of Cluj, Craiova, Pitesti and Ploiesti during 1957-1970 and the separation technology tested at Ramnicu-Valcea pilot plant (at present the Cryogenics and Isotope Separation Institute). The first investments at ROMAG PROD were made in 1979 and on July 17, 1988 was produced the first amount of heavy water at the required parameters for CANDU type nuclear reactors. The period between 1990-1992 was dedicated to the project completion, upgrading the technological facilities and retrofitting the environmental protection and monitoring systems. Production was resumed in 1992. The first 500 t of heavy water required for the Cernavoda NPP first reactor operation were produced by summer 1997. The additional amount of 500 t of heavy water was produced between 1997-2001. ROMAG PROD obtained the ISO 9001/2001 certificate for the quality management system, the ISO 14001/1997 certificate for the environmental management system and the new environmental permit

  2. Design of ultrasonic probe and evaluation of ultrasonic waves on E.coli in Sour Cherry Juice

    Directory of Open Access Journals (Sweden)

    B Hosseinzadeh Samani

    2015-09-01

    Full Text Available Introduction: The common method used for juice pasteurization is the thermal method since thermal methods contribute highly to inactivating microbes. However, applying high temperatures would lead to inefficient effects on nutrition and food value. Such effects may include vitamin loss, nutritional flavor loss, non-enzyme browning, and protein reshaping (Kuldiloke, 2002. In order to decrease the adverse effects of the thermal pasteurization method, other methods capable of inactivation of microorganisms can be applied. In doing so, non-thermal methods including pasteurization using high hydrostatic pressure processing (HPP, electrical fields, and ultrasound waves are of interest (Chen and Tseng, 1996. The reason for diminishing microbial count in the presence of ultrasonic waves could be due to the burst of very tiny bubbles developed by ultrasounds which expand quickly and burst in a short time. Due to this burst, special temperature and pressure conditions are developed which could initiate or intensify several physical and/or chemical reactions. The aim of this study is to evaluate the non-thermal ultrasonic method and its effective factors on the E.coli bacteria of sour cherry. Materials and methods: In order to supply uniform ultrasonic waves, a 1000 W electric generator (Model MPI, Switzerland working at 20±1 kHz frequency was used. The aim of this study is to evaluate the non-thermal ultrasonic method and its effective factors on the E.coli bacteria of sour cherry. For this purpose, a certain amount of sour cherry fruit was purchased from local markets. First, the fruits were washed, cleaned and cored. The prepared fruits were then dewatered using an electric juicer. In order to separate pulp suspensions and tissue components, the extracted juice was poured into a centrifuge with the speed of 6000 rpm for 20 min. For complete separation of the remaining suspended particles, the transparent portion of the extract was passed through a

  3. Radiological quality of packaged waters produced in France

    International Nuclear Information System (INIS)

    Franques, Nathalie; Perrin, Marie-Line; Godet, Jean-Luc; Pineau, Cyril; Loyen, Jeanne; Brassac, Annette; Gleizes, Marc; Baudry, Michel

    2013-09-01

    Based on radionuclide and uranium analyses performed in 2012 by the IRSN on packaged waters produced in France, this report presents the main results on this national survey. The objectives were a systematic measurement of radioactivity indicators, a systematic measurement of uranium content, and a limited measurement of radon-222 content in some samples. After some recalls on the notions of radioactivity and exposure, on uranium and radon properties, and of the present regulation, this report presents the adopted methodology, and discusses the range and limitation of this study. It presents and comments the results of systematic analyses of spring and natural mineral waters (presence of tritium, global beta and alpha activity, uranium concentration), the results of measurements of radon-222, and the results of additional analyses of spring and natural mineral waters (main radionuclides, radium-226, uranium isotopes, other radionuclides). It reports the calculation of doses and the interpretation of results for waters which have been submitted to additional analyses

  4. Radionuclides in produced water from Norwegian oil and gas installations — Concentrations and bioavailability

    Science.gov (United States)

    Eriksen, D. Ø.; Sidhu, R.; Strålberg, E.; Iden, K. I.; Hylland, K.; Ruus, A.; Røyset, O.; Berntssen, M. H. G.; Rye, H.

    2006-01-01

    Substantial amounts of produced water, containing elevated levels of radionuclides (mainly 226Ra and 228Ra) are discharged to the sea as a result of oil and gas production on the Norwegian Continental Shelf. So far no study has assessed the potential radiological effects on marine biota in connection with radionuclide discharges to the North Sea. The main objective of the project is to establish radiological safe discharge limits for radium, lead and polonium associated with other components in produced water from oil and gas installations on the Norwegian continental shelf. This study reports results indicating that the presence of added chemicals such as scale inhibitors in produced water has a marked influence on the formation of radium and barium sulphates when produced water is mixed with sea water. Thus, the mobility and bioavailability of radium (and barium) will be larger than anticipated. Also, the bioavailability of food-borne radium is shown to increase due to presence of such chemicals.

  5. Phenols biodegradation in waste waters from petroleum industry

    International Nuclear Information System (INIS)

    Grosso V, J.L.; Diaz M, M.P.; Leon, G.

    1995-01-01

    Practical methods to isolate, adapt and propagate phenol biodegradation microorganisms were established. Fifteen different microorganism group were obtained, capable of eliminating phenol contained in production water, sour water and waste water from Barrancabermeja's Refinery (Colombia), and dehydration water from heavy oil-in-water emulsions. Elimination efficiencies higher than 95% in periods of time shorter than 24 hour were achieved at laboratory and pilot plant scales. A continuos system using this technology was successfully implemented in April 1994, for the treatment of waste water from Colombia's biggest refinery. Existing stabilizing pools were converted into bioreactors capable of handling water flow rates between 16.000 to 32.000 m3/d. Efficiencies close to 95% have obtained under controlled acidity, aeration and flow rate conditions. This technology is being implemented in other Ecopetrol refineries and production fields

  6. Produced water treatment for beneficial use : emulsified oil removal

    NARCIS (Netherlands)

    Waisi, Basma

    2016-01-01

    The development of novel carbon material, high accessible surface area, interconnected porosity, and stable nanofiber nonwoven media for emulsified oil droplets separation from oily wastewater, in particular for oilfields produced water treatment, is discussed in this thesis. Firstly, the quantity

  7. Surface Studies of Ultra Strength Drilling Steel after Corrosion Fatigue in Simulated Sour Environment

    Energy Technology Data Exchange (ETDEWEB)

    M. Ziomek-Moroz; J.A. Hawk; R. Thodla; F. Gui

    2012-05-06

    The Unites States predicted 60% growth in energy demand by 2030 makes oil and natural gas primary target fuels for energy generation. The fact that the peak of oil production from shallow wells (< 5000 m) is about to be reached, thereby pushing the oil and natural gas industry into deeper wells. However, drilling to depths greater than 5000 m requires increasing the strength-to weight ratio of the drill pipe materials. Grade UD-165 is one of the ultra- high yield strength carbon steels developed for ultra deep drilling (UDD) activities. Drilling UDD wells exposes the drill pipes to Cl{sup -}, HCO{sub 3}{sup -}/CO{sub 3}{sup 2-}, and H{sub 2}S-containig corrosive environments (i.e., sour environments) at higher pressures and temperatures compared to those found in conventional wells. Because of the lack of synergism within the service environment, operational stresses can result in catastrophic brittle failures characteristic for environmentally assisted cracking (EAC). Approximately 75% of all drill string failures are caused by fatigue or corrosion fatigue. Since there is no literature data on the corrosion fatigue performance of UD-165 in sour environments, research was initiated to better clarify the fatigue crack growth (FCGR) behavior of this alloy in UDD environments. The FCGR behavior of ultra-strength carbon steel, grade UD-165, was investigated by monitoring crack growth rate in deaerated 5%NaCl solution buffered with NaHCO{sub 3}/Na{sub 2}CO{sub 3} and in contact with H{sub 2}S. The partial pressure of H{sub 2}S (p{sub H2S}) was 0.83 kPa and pH of the solution was adjusted by NaOH to 12. The fatigue experiments were performed at 20 and 85 C in an autoclave with surface investigations augmented by scanning electron microscopy (SEM) and energy dispersive x-ray (EDX) spectroscopy. In this study, research focused on surface analyses supported by the fatigue crack growth rate measurements. Fig. 1 shows an SEM micrograph of the crack that propagated from the

  8. Produced water discharges to the Gulf of Mexico: Background information for ecological risk assessments

    Energy Technology Data Exchange (ETDEWEB)

    Meinhold, A.F.; Holtzman, S.; DePhillips, M.P.

    1996-06-01

    This report reviews ecological risk assessment concepts and methods; describes important biological resources in the Gulf of Mexico of potential concern for produced water impacts; and summarizes data available to estimate exposure and effects of produced water discharges. The emphasis is on data relating to produced water discharges in the central and western Gulf of Mexico, especially in Louisiana. Much of the summarized data and cited literature are relevant to assessments of impacts in other regions. Data describing effects on marine and estuarine fishes, mollusks, crustaceans and benthic invertebrates are emphasized. This review is part of a series of studies of the health and ecological risks from discharges of produced water to the Gulf of Mexico. These assessments will provide input to regulators in the development of guidelines and permits, and to industry in the use of appropriate discharge practices.

  9. Produced water discharges to the Gulf of Mexico: Background information for ecological risk assessments

    International Nuclear Information System (INIS)

    Meinhold, A.F.; Holtzman, S.; DePhillips, M.P.

    1996-06-01

    This report reviews ecological risk assessment concepts and methods; describes important biological resources in the Gulf of Mexico of potential concern for produced water impacts; and summarizes data available to estimate exposure and effects of produced water discharges. The emphasis is on data relating to produced water discharges in the central and western Gulf of Mexico, especially in Louisiana. Much of the summarized data and cited literature are relevant to assessments of impacts in other regions. Data describing effects on marine and estuarine fishes, mollusks, crustaceans and benthic invertebrates are emphasized. This review is part of a series of studies of the health and ecological risks from discharges of produced water to the Gulf of Mexico. These assessments will provide input to regulators in the development of guidelines and permits, and to industry in the use of appropriate discharge practices

  10. Functionalized sio2 microspheres for extracting oil from produced water

    KAUST Repository

    Mishra, Himanshu

    2017-03-16

    Functionalized material, methods of producing the functionalized material, and use thereof for separation processes such as but not limited to use for separating and extracting a dissolved organic foulant, charged contaminant or oily matter or any combination thereof from water, such as produced water, are provided. In an embodiment, the functionalized material is a mineral material, such as mica, silica (e.g. an SiO2 microsphere) or a metal oxide, and the outer surface of the material is functionalized with an alkyl chain or a perfluorinated species. In an embodiment, the method of making the functionalized material, includes: a) providing a mineral material; b) providing an alkyl chain and/or a perfluorinated species, the alkyl chain or perfluorinated species selected to dissolve organic foulants, charged contaminants or oily matter from water or any combination thereof; c) hydroxylating the material via a concentrated acid solution or a basic solution; and d) grafting the alkyl chain and/or the perfluorinated species onto the material via a silanation reaction.

  11. Treatment of offshore produced water - an effective membrane process

    International Nuclear Information System (INIS)

    Taylor, J.; Larson, R.; Scherer, B.

    1991-01-01

    The conference paper describes a new membrane technology being extremely effective in separating hydrocarbons from water streams. The membrane is composed of a completely natural cellulose and is resistant to all hydrocarbons and organic solvents, and preliminary tests have shown that it is resistant to fouling by oily molecules and calcium scaling. The membrane system being designed shows good potential for the treatment of offshore produced water with a hydrocarbon content well within present and emerging standards. 6 refs., 8 figs., 3 tabs

  12. Organic Pollutants in Shale Gas Flowback and Produced Waters

    NARCIS (Netherlands)

    Butkovskyi, Andrii; Bruning, Harry; Kools, Stefan A.E.; Rijnaarts, Huub H.M.; Wezel, van Annemarie P.

    2017-01-01

    Organic contaminants in shale gas flowback and produced water (FPW) are traditionally expressed as total organic carbon (TOC) or chemical oxygen demand (COD), though these parameters do not provide information on the toxicity and environmental fate of individual components. This review addresses

  13. Precipitation hardened nickel-base alloys for sour gas environments

    International Nuclear Information System (INIS)

    Igarashi, M.; Mukai, S.; Kudo, T.; Okada, Y.; Ikeda, A.

    1987-01-01

    SCC (Stress Corrosion Cracking) in sour gas environments of γ'(gamma prime: Ni/sub 3/(Ti and/or Al)) and γ''(gamma double prime: Ni/sub 3/Nb) precipitation hardened nickel-base alloys has been studied using the SSRT (Slow Strain Rate Tensile) test, anodic polarization measurement and transmission electron microscopy (TEM). The γ'-type alloy containing Ti was more susceptible to SCC in the SSRT tests up to 350 0 F(450 K) than the γ''-type alloy containing Nb. The susceptibility to SCC was related to their deformation structures in terms of stress localization and sensitivity to pitting corrosion in H/sub 2/S solutions. TEM observation showed the γ'-type alloy deformed by the superlattice dislocations in coplanar structures. This mode of deformation induced the stress localization to some boundaries such as grain boundary and as a result the susceptibility to SCC of the γ'-type alloy was increased. On the other hand, the γ''-type alloy deformed by the massive dislocation not in coplanar structures so that it was less susceptible to SCC in terms of the stress localization. The anodic polarization measurement suggested the γ'-type alloy was more susceptible to pitting corrosion compared with the γ''-type alloy

  14. Molecular imprinted hydrogel polymer (MIHP) as microbial immobilization media in artificial produced water treatment

    Science.gov (United States)

    Kardena, E.; Ridhati, S. L.; Helmy, Q.

    2018-01-01

    Produced water generated during oil and gas exploration and drilling, consists of many chemicals which used in drilling process. The production of produced water is over three fold of the oil production. The water-cut has increased over time and continues to do so because the fraction of oil in the reservoir decreases and it is more difficult to get the oil out from an old oil-field. It therefore requires more sea water to be injected in order to force the oil out; hence more produced water is generated. Produced water can pollute the environment if it is not treated properly. In this research, produced water will be treated biologically using bacterial consortium which is isolated from petroleum processing facility with Molecular Imprinted Hydrogel Polymer (MIHP) for microbial immobilization media. Microbial growth rate is determined by measuring the MLVSS and hydrogel mass, also by SEM-EDS analysis. SEM-EDS analysis is an analysis to evidence the presence of microbe trapped in hydrogel, and also to determine the types and weight of the molecules of hydrogel. From this research, suspended microbial growth rate was found at 0.1532/days and attached microbial growth rate was 0.3322/days. Furthermore, based on SEM analysis, microbe is entrapped inside the hydrogel. Effectiveness of microbial degradation activity was determined by measuring organic materials as COD. Based on COD measurement, degradation rate of organic materials in wastewater is 0.3089/days, with maximum COD removal efficiency of 76.67%.

  15. Petroleum-related contaminants near a produced water discharge site in the Santa Barbara Channel

    International Nuclear Information System (INIS)

    Jones, A.D.; Witter, A.E.; Higashi, R.M.

    1994-01-01

    Offshore oil production generates substantial quantities of waste water that is frequently discharged into marine waters. Contamination of coastal sediments occurs due to other inputs including natural petroleum seeps, and this complicates assessments of the environmental effects of produced water in marine ecosystems. The current study has focused on characterization of contaminants in sediments near produced water discharge site off the coast of Southern California. First, it was important to address the question: ''What contaminants in sediments should be monitored as indicators of produced water effects?'' Dichloromethane extracts of sediments were analyzed for numerous organic constituents using gas chromatography-mass spectrometry and selected ion monitoring. Though the phenols and fatty acids were not detected in sediment extracts, normal and branched alkanes and other petroleum hydrocarbon biomarkers were quantified. No relationship was evident that related absolute concentrations of organic compounds to distance from the outfall, but patterns of petroleum hydrocarbons exhibited consistent spatial variations that could be related to distance from the produced water out fall. Analysis of chemical fossil ''biomarkers'' provides potentially useful indices of effects of waste discharges upon microbial biodegradation of organic compounds in sediments

  16. Advanced Membrane Filtration Technology for Cost Effective Recovery of Fresh Water from Oil & Gas Produced Brine

    Energy Technology Data Exchange (ETDEWEB)

    David B. Burnett

    2004-09-29

    Produced water is a major waste generated at the oil and natural gas wells in the state of Texas. This water could be a possible source of new fresh water to meet the growing demands of the state after treatment and purification. Treatment of brine generated in oil fields or produced water with an ultrafiltration membranes were the subject of this thesis. The characterization of ultrafiltration membranes for oil and suspended solids removal of produced water, coupled with the reverse osmosis (RO) desalination of brine were studied on lab size membrane testing equipment and a field size testing unit to test whether a viable membrane system could be used to treat produced water. Oil and suspended solids were evaluated using turbidity and oil in water measurements taken periodically. The research considered the effect of pressure and flow rate on membrane performance of produced water treatment of three commercially available membranes for oily water. The study also analyzed the flux through the membrane and any effect it had on membrane performance. The research showed that an ultrafiltration membrane provided turbidity removal of over 99% and oil removal of 78% for the produced water samples. The results indicated that the ultrafiltration membranes would be asset as one of the first steps in purifying the water. Further results on selected RO membranes showed that salt rejection of greater than 97% could be achieved with satisfactory flux and at reasonable operating cost.

  17. Coalbed methane produced water in China: status and environmental issues.

    Science.gov (United States)

    Meng, Yanjun; Tang, Dazhen; Xu, Hao; Li, Yong; Gao, Lijun

    2014-01-01

    As one of the unconventional natural gas family members, coalbed methane (CBM) receives great attention throughout the world. The major associated problem of CBM production is the management of produced water. In the USA, Canada, and Australia, much research has been done on the effects and management of coalbed methane produced water (CMPW). However, in China, the environmental effects of CMPW were overlooked. The quantity and the quality of CMPW both vary enormously between coal basins or stratigraphic units in China. The unit produced water volume of CBM wells in China ranges from 10 to 271,280 L/well/day, and the concentration of total dissolved solids (TDS) ranges from 691 to 93,898 mg/L. Most pH values of CMPW are more than 7.0, showing the alkaline feature, and the Na-HCO3 and Na-HCO3-Cl are typical types of CMPW in China. Treatment and utilization of CMPW in China lag far behind the USA and Australia, and CMPW is mainly managed by surface impoundments and evaporation. Currently, the core environmental issues associated with CMPW in China are that the potential environmental problems of CMPW have not been given enough attention, and relevant regulations as well as environmental impact assessment (EIA) guidelines for CMPW are still lacking. Other potential issues in China includes (1) water quality monitoring issues for CMPW with special components in special areas, (2) groundwater level decline issues associated with the dewatering process, and (3) potential environmental issues of groundwater pollution associated with hydraulic fracturing.

  18. Plant-wide Control Strategy for Improving Produced Water Treatment

    DEFF Research Database (Denmark)

    Yang, Zhenyu; Pedersen, Simon; Løhndorf, Petar Durdevic

    2016-01-01

    This work focuses on investigation and development of an innovative Produced Water Treatment (PWT) technology for offshore oil & gas production by employing the model-based plant-wide control strategy. The key contributions lie in two folds: (i) the advanced anti-slug analysis and control...

  19. Biological treatment process for removing petroleum hydrocarbons from oil field produced waters

    Energy Technology Data Exchange (ETDEWEB)

    Tellez, G.; Khandan, N.

    1995-12-31

    The feasibility of removing petroleum hydrocarbons from oil fields produced waters using biological treatment was evaluated under laboratory and field conditions. Based on previous laboratory studies, a field-scale prototype system was designed and operated over a period of four months. Two different sources of produced waters were tested in this field study under various continuous flow rates ranging from 375 1/D to 1,800 1/D. One source of produced water was an open storage pit; the other, a closed storage tank. The TDS concentrations of these sources exceeded 50,000 mg/l; total n-alkanes exceeded 100 mg/l; total petroleum hydrocarbons exceeded 125 mg/l; and total BTEX exceeded 3 mg/l. Removals of total n-alkanes, total petroleum hydrocarbons, and BTEX remained consistently high over 99%. During these tests, the energy costs averaged $0.20/bbl at 12 bbl/D.

  20. Response of range grasses to water produced from in situ fossil fuel processing

    Energy Technology Data Exchange (ETDEWEB)

    Skinner, Q D; Moore, T S; Sexton, J C

    1984-11-01

    In situ-produced waters collected while retorting oil shale and tar sands to produce oil, and coal to produce gas, were tested for their effects on plant growth. Basin wildrye (Elymus cinereus), western wheatgrass (Agropyron smithii) 'Rosana', alkali sacaton (Sporobolus airoides), bluebunch wheatgrass (Agropyron spicatum) and Nuttall alkaligrass (Puccinellia airoides) were utilized. Root weight, shoot weight, total dry weight, leaf area and root/shoot weight ratios were determined. All experiments were conducted under greenhouse conditions using hydroponic techniques and horticultural grade perlite for plant support. Measurements were collected after a 10-week growth period. Results show that differences in plant growth can be monitored using dry biomass, leaf area and root to shoot ratio measurements when plants are subjected to retort waters. Plant species reaction to a water may be different. Generally, alkali sacaton, basin wildrye and western wheatgrass are least susceptible to toxicity by the majority of retort waters tested. Bluebunch wheatgrass is most susceptible. Waters from different retort procedures vary in toxicity to different plant species.

  1. Re-injection of produced water: ''Environmental friendliness pays off''

    International Nuclear Information System (INIS)

    Bjerke, E.

    1995-01-01

    The article deals with the re-injection of produced water for minimizing the emission of polluting components and for enhancing the oil recovery on the Norwegian oil field Ula. A closed cycle system is installed increasing the oil production by 4-5.000 bbl per day

  2. Reuse of Produced Water from CO2 Enhanced Oil Recovery, Coal-Bed Methane, and Mine Pool Water by Coal-Based Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Knutson, Chad [Univ. of Illinois, Champaign, IL (United States); Dastgheib, Seyed A. [Univ. of Illinois, Champaign, IL (United States); Yang, Yaning [Univ. of Illinois, Champaign, IL (United States); Ashraf, Ali [Univ. of Illinois, Champaign, IL (United States); Duckworth, Cole [Univ. of Illinois, Champaign, IL (United States); Sinata, Priscilla [Univ. of Illinois, Champaign, IL (United States); Sugiyono, Ivan [Univ. of Illinois, Champaign, IL (United States); Shannon, Mark A. [Univ. of Illinois, Champaign, IL (United States); Werth, Charles J. [Univ. of Illinois, Champaign, IL (United States)

    2012-07-01

    Power generation in the Illinois Basin is expected to increase by as much as 30% by the year 2030, and this would increase the cooling water consumption in the region by approximately 40%. This project investigated the potential use of produced water from CO2 enhanced oil recovery (CO2-EOR) operations; coal-bed methane (CBM) recovery; and active and abandoned underground coal mines for power plant cooling in the Illinois Basin. Specific objectives of this project were: (1) to characterize the quantity, quality, and geographic distribution of produced water in the Illinois Basin; (2) to evaluate treatment options so that produced water may be used beneficially at power plants; and (3) to perform a techno-economic analysis of the treatment and transportation of produced water to thermoelectric power plants in the Illinois Basin. Current produced water availability within the basin is not large, but potential flow rates up to 257 million liters per day (68 million gallons per day (MGD)) are possible if CO2-enhanced oil recovery and coal bed methane recovery are implemented on a large scale. Produced water samples taken during the project tend to have dissolved solids concentrations between 10 and 100 g/L, and water from coal beds tends to have lower TDS values than water from oil fields. Current pretreatment and desalination technologies including filtration, adsorption, reverse osmosis (RO), and distillation can be used to treat produced water to a high quality level, with estimated costs ranging from $2.6 to $10.5 per cubic meter ($10 to $40 per 1000 gallons). Because of the distances between produced water sources and power plants, transportation costs tend to be greater than treatment costs. An optimization algorithm was developed to determine the lowest cost pipe network connecting sources and sinks. Total water costs increased with flow rate up to 26 million liters per day (7 MGD), and the range was from $4 to $16 per cubic meter

  3. Key technologies for well drilling and completion in ultra-deep sour gas reservoirs, Yuanba Gasfield, Sichuan Basin

    Directory of Open Access Journals (Sweden)

    Jiaxiang Xia

    2016-12-01

    Full Text Available The Yuanba Gasfield is a large gas field discovered by Sinopec in the Sichuan Basin in recent years, and another main exploration area for natural gas reserves and production increase after the Puguang Gasfield. The ultra-deep sour gas reservoir in the Yuanba Gasfield is characterized by complicated geologic structure, deep reservoirs and complex drilled formation, especially in the continental deep strata which are highly abrasive with low ROP (rate of penetration and long drilling period. After many years of drilling practice and technical research, the following six key drilling and completion technologies for this type reservoir are established by introducing new tools and technologies, developing specialized drill bits and optimizing drilling design. They are: casing program optimization technology for ROP increasing and safe well completion; gas drilling technology for shallow continental strata and high-efficiency drilling technology for deep high-abrasion continental strata; drilling fluid support technologies of gas–liquid conversion, ultra-deep highly-deviated wells and horizontal-well lubrication and drag reduction, hole stability control and sour gas contamination prevention; well cementing technologies for gas medium, deep-well long cementing intervals and ultra-high pressure small space; horizontal-well trajectory control technologies for measuring instrument, downhole motor optimization and bottom hole assembly design; and liner completion modes and completion string optimization technologies suitable for this gas reservoir. Field application shows that these key technologies are contributive to ROP increase and efficiency improvement of 7000 m deep horizontal wells and to significant operational cycle shortening.

  4. Alternative movement : collaborative project has researchers looking to ceramic membranes to improve produced water treatment

    Energy Technology Data Exchange (ETDEWEB)

    Wells, P.

    2009-10-15

    Ceramic membranes have high chemical and thermal stability coupled with mechanical strength and are therefore used in a range of microfiltration, ultrafiltration and nanofiltration applications. This article described a new technology that involves the use of ceramic membranes in the treatment of produced water in thermal heavy oil recovery operations. The efficacy of advanced ceramic nano-membrane technology (CMT) is being examined in bench-scale experiments at the Southern Alberta Institute of Technology (SAIT) in collaboration with the department of chemical and petroleum engineering at the University of Calgary. In one project, next-generation ceramic membrane technology is being used as part of the overall treatment process of produced water. The project is funded through a Canadian Association of Petroleum Producers fund and the Alberta Department of Energy. It is facilitated by the Petroleum Technology Alliance Canada in an effort to find cost-effective treatment solutions for recycling produced water for the conventional oil and gas industry. The key objective is to increase the amount of produced water that can be reused rather than disposed into deep saline aquifers. The research focuses on the pre-treatment of produced water and related salt impacted water by using ceramic membranes for the removal of organic compounds for beneficial reuse downstream. Ceramic membranes consist of a multilayer system and their performance depends on the separation and permeation properties of the membrane as well as its mechanical integrity. It was concluded that the CMT findings will be beneficial to the oil and gas industry in providing practical solutions for the challenging issues associated with de-oiling and produced water treatment. 2 figs.

  5. A numerical study of under-deposit pitting corrosion in sour petroleum pipelines

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Z.; Sand, K.W.; Teevens, P.J. [Broadsword Corrosion Engineering Ltd., Calgary, AB (Canada)

    2010-07-01

    Insufficient fluid velocity in petroleum pipelines can lead to the deposit of sand, corrosion products, and non-corrosion products on the pipe's metal surface, which in turn can lead to pitting corrosion. There is currently no reliable means of detecting and preventing the pitting process. This paper presented a computerized simulation tool that used the finite element method to model mass transfer-governed internal pitting corrosion under solids deposition in sour petroleum pipelines. The computational domain consisted of a hemispherical pit and a thin stagnant solution film under a surface deposit. The moving mesh method was used to track pitting growth. A Poisson equation was used to determine aqueous path migration of ions. Pitting corrosion rates were estimated using the Nernst-Planck equation. The model was used to predict the effects of different operating parameters on pitting corrosion rates. The model can be used to develop pigging and in-line-inspection (ILI) procedures. 35 refs., 2 tabs., 16 figs.

  6. Polyoxadiazole hollow fibers for produced water treatment by direct contact membrane distillation

    KAUST Repository

    Xu, Jingli; Srivatsa Bettahalli, N.M.; Chisca, Stefan; Khalid, Mohammed Khalil; Ghaffour, NorEddine; Vilagines, Ré gis; Nunes, Suzana Pereira

    2018-01-01

    Treatment of produced water in the petroleum industry has been a challenge worldwide. In this study, we evaluated the use of direct contact membrane distillation (DCMD) for this purpose, removing oil and dissolved elements and supplying clean water

  7. Organic compounds in produced waters from coalbed natural gas wells in the Powder River Basin, Wyoming, USA

    Science.gov (United States)

    Orem, W.H.; Tatu, C.A.; Lerch, H.E.; Rice, C.A.; Bartos, T.T.; Bates, A.L.; Tewalt, S.; Corum, M.D.

    2007-01-01

    The organic composition of produced water samples from coalbed natural gas (CBNG) wells in the Powder River Basin, WY, sampled in 2001 and 2002 are reported as part of a larger study of the potential health and environmental effects of organic compounds derived from coal. The quality of CBNG produced waters is a potential environmental concern and disposal problem for CBNG producers, and no previous studies of organic compounds in CBNG produced water have been published. Organic compounds identified in the produced water samples included: phenols, biphenyls, N-, O-, and S-containing heterocyclic compounds, polycyclic aromatic hydrocarbons (PAHs), aromatic amines, various non-aromatic compounds, and phthalates. Many of the identified organic compounds (phenols, heterocyclic compounds, PAHs) are probably coal-derived. PAHs represented the group of organic compounds most commonly observed. Concentrations of total PAHs ranged up to 23 ??g/L. Concentrations of individual compounds ranged from about 18 to compound concentrations was documented, as two wells with relatively high organic compound contents in produced water in 2001 had much lower concentrations in 2002. In many areas, including the PRB, coal strata provide aquifers for drinking water wells. Organic compounds observed in produced water are also likely present in drinking water supplied from wells in the coal. Some of the organic compounds identified in the produced water samples are potentially toxic, but at the levels measured in these samples are unlikely to have acute health effects. The human health effects of low-level, chronic exposure to coal-derived organic compounds in drinking water are currently unknown. Continuing studies will evaluate possible toxic effects from low level, chronic exposure to coal-derived organic compounds in drinking water supplies.

  8. Experimental use of produced waters for waterflooding fields of Kuibyshev region

    Energy Technology Data Exchange (ETDEWEB)

    Palii, P A; Gavura, V E; Redkin, I I; Sokolov, A G

    1970-01-01

    Large volumes of produced waters have been used for waterflooding in the Kuibyshev region. Before underground injection, the water is conditioned by short-term storage. The treated water contains emulsified oil, suspended solids, hydrogen sulfide, and ferrous iron. This water is readily injected into fractured porous formations, even if suspended solids reach 42 mg/liter and emulsifed oil 67 mg/liter. However, better quality water has to be injected into nonfractured formations. In this case, the concentration of emulsified oil and suspended solids needs to be kept below 5 mg/liter. If concentration of suspended material exceeds this limit, water injectivity decreases rapidly. The partially plugged wells can be restored by acid treatment. Water injection has shown large economic gains in this region.

  9. Technique of optimum extraction of pectin from sour orange peels and its chemical evaluation

    International Nuclear Information System (INIS)

    Abid, H.; Hussain, A.; Ali, J.

    2009-01-01

    The extraction of pectin from sour orange peels and effect of pH, temperature, extraction time on the yield and quality of pectin was studied. The extracting reagent was 0.1 N sulphuric acid and variables were pH (1.5, 2.5 and 3.5), extraction time (30, 60 and 120 minutes) and temperature (70 degree C, 80 degree C arid 90 degree C). These variables were significantly affected the extraction of pectin. The best yield (16.10 %) was obtained on soaking the finely ground peels in the sulphuric acid solution of pH, 25 at 80 degree C for 120 minutes. Anhydrogalacturonic acid, methoxyl content were 7310 % and 9.93 %, respectively, while equivalent weight value 945 was obtained by using pH, 2.5 at 80 degree C for 120 minutes. (author)

  10. Geochemical and strontium isotope characterization of produced waters from Marcellus Shale natural gas extraction.

    Science.gov (United States)

    Chapman, Elizabeth C; Capo, Rosemary C; Stewart, Brian W; Kirby, Carl S; Hammack, Richard W; Schroeder, Karl T; Edenborn, Harry M

    2012-03-20

    Extraction of natural gas by hydraulic fracturing of the Middle Devonian Marcellus Shale, a major gas-bearing unit in the Appalachian Basin, results in significant quantities of produced water containing high total dissolved solids (TDS). We carried out a strontium (Sr) isotope investigation to determine the utility of Sr isotopes in identifying and quantifying the interaction of Marcellus Formation produced waters with other waters in the Appalachian Basin in the event of an accidental release, and to provide information about the source of the dissolved solids. Strontium isotopic ratios of Marcellus produced waters collected over a geographic range of ~375 km from southwestern to northeastern Pennsylvania define a relatively narrow set of values (ε(Sr)(SW) = +13.8 to +41.6, where ε(Sr) (SW) is the deviation of the (87)Sr/(86)Sr ratio from that of seawater in parts per 10(4)); this isotopic range falls above that of Middle Devonian seawater, and is distinct from most western Pennsylvania acid mine drainage and Upper Devonian Venango Group oil and gas brines. The uniformity of the isotope ratios suggests a basin-wide source of dissolved solids with a component that is more radiogenic than seawater. Mixing models indicate that Sr isotope ratios can be used to sensitively differentiate between Marcellus Formation produced water and other potential sources of TDS into ground or surface waters.

  11. Study on fracture and stress corrosion cracking behavior of casing sour service materials

    International Nuclear Information System (INIS)

    Sequera, C.; Gordon, H.

    2003-01-01

    Present work describes sulphide stress corrosion cracking and fracture toughness tests performed to high strength sour service materials of T-95, C-100 and C-110 oil well tubular grades. P-110 was considered as a reference case, since it is one of the high strength materials included in specification 5CT of American Petroleum Institute, API. Sulphide stress corrosion cracking, impact and fracture toughness values obtained in the tests show that there is a correspondence among them. A decreasing classification order was established, namely C-100, T-95, C-110 and P-110. Special grades steels studied demonstrated a better behavior in the evaluated properties than the reference case material grade: P-110. Results obtained indicate that a higher sulphide stress corrosion cracking resistance is related to a higher toughness. The fracture toughness results evidence the hydrogen influence on reducing the toughness values. (author)

  12. Performance of two quantitative PCR methods for microbial source tracking of human sewage and implications for microbial risk assessment in recreational waters

    Science.gov (United States)

    Before new, rapid quantitative PCR (qPCR) methods for recreational water quality assessment and microbial source tracking (MST) can be useful in a regulatory context, an understanding of the ability of the method to detect a DNA target (marker) when the contaminant soure has been...

  13. Reaction of Aluminum with Water to Produce Hydrogen - 2010 Update

    Energy Technology Data Exchange (ETDEWEB)

    Petrovic, John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Thomas, George [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2011-06-01

    A Study of Issues Related to the Use of Aluminum for On-Board Vehicular Hydrogen Storage The purpose of this White Paper is to describe and evaluate the potential of aluminum-water reactions for the production of hydrogen for on-board hydrogen-powered vehicle applications. Although the concept of reacting aluminum metal with water to produce hydrogen is not new, there have been a number of recent claims that such aluminum-water reactions might be employed to power fuel cell devices for portable applications such as emergency generators and laptop computers, and might even be considered for possible use as the hydrogen source for fuel cell-powered vehicles.

  14. A review on risk assessment techniques for hydraulic fracturing water and produced water management implemented in onshore unconventional oil and gas production.

    Science.gov (United States)

    Torres, Luisa; Yadav, Om Prakash; Khan, Eakalak

    2016-01-01

    The objective of this paper is to review different risk assessment techniques applicable to onshore unconventional oil and gas production to determine the risks to water quantity and quality associated with hydraulic fracturing and produced water management. Water resources could be at risk without proper management of water, chemicals, and produced water. Previous risk assessments in the oil and gas industry were performed from an engineering perspective leaving aside important social factors. Different risk assessment methods and techniques are reviewed and summarized to select the most appropriate one to perform a holistic and integrated analysis of risks at every stage of the water life cycle. Constraints to performing risk assessment are identified including gaps in databases, which require more advanced techniques such as modeling. Discussions on each risk associated with water and produced water management, mitigation strategies, and future research direction are presented. Further research on risks in onshore unconventional oil and gas will benefit not only the U.S. but also other countries with shale oil and gas resources. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Risk assessment for produced water discharges to Louisiana Open Bays

    Energy Technology Data Exchange (ETDEWEB)

    Meinhold, A.F.; DePhillips, M.P.; Holtzman, S.

    1995-06-23

    Data were collected prior to termination of discharge at three sites (including two open bay sites at Delacroix Island and Bay De Chene) for the risk assessments. The Delacroix Island Oil and Gas Field has been in production since the first well drilling in 1940; the Bay De Chene Field, since 1942. Concentrations of 226Ra, 228Ra, 210Po, and 228Th were measured in discharges. Radium conc. were measured in fish and shellfish tissues. Sediment PAH and metal conc. were also available. Benthos sampling was conducted. A survey of fishermen was conducted. The tiered risk assessment showed that human health risks from radium in produced water appear to be small; ecological risk from radium and other radionuclides in produced water also appear small. Many of the chemical contaminants discharged to open Louisiana bays appear to present little human health or ecological risk. A conservative screening analysis suggested potential risks to human health from Hg and Pb and a potential risk to ecological receptors from total effluent, Sb, Cd, Cu, Pb, Ni, Ag, Zn, and phenol in the water column and PAHs in sediment; quantitiative risk assessments are being done for these contaminants.

  16. Perceived risks of produced water management and naturally occurring radioactive material content in North Dakota.

    Science.gov (United States)

    Torres, Luisa; Yadav, Om Prakash; Khan, Eakalak

    2017-07-01

    Unconventional oil and gas development using hydraulic fracturing has caused conflict and controversy across the globe including the U.S. where some States banned the practice. Nevertheless, North Dakota (ND) has supported the practice because the State perceives the risks to be acceptable and because it has brought growth and opportunities to small communities. However, social acceptance of new technology is based on a number of factors and not contingent on economic benefits. To date, no research has been conducted to understand public risk perception of hazards associated with produced water from hydraulic fracturing in ND. This study focuses on understanding the risk perception of select ND stakeholder groups regarding produced water management and naturally occurring radioactive material. The software Qualtrics was used to create an online survey, collect data, and perform statistical analysis. The most important variables that seem to influence risk perception are the images and thoughts associated with produced water, level of knowledge about produced water handling and content, and knowing how to proceed in case of a spill of produced water. Overall, social risk perception could be in alignment with actual technical risk if availability of objective information is improved. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Renovate produced-water-treating facilities to handle increased water cuts

    International Nuclear Information System (INIS)

    Murti, D.G.K.; Al-Nuaimi, H.R.

    1991-01-01

    This paper reports on the modified skimmer tanks that have consistently demonstrated superior oil recovery characteristics compared to conventional design in an oil field tank battery system. The modified tanks have been in continuous service for more than 3 years in one of the oldest oil fields in the Arabian Gulf. The new design has helped recover skimmed oil from a mere 6 bpd (1.0 m 3 ) to more than 55 bpd (8.75 m 3 ) from produced water in a tank battery system alone. The recovery is expected to improve by up to 200 bpd (31.8 m 3 ) once skimmer tanks in all the tank batteries are upgraded to the new design

  18. Mapping the energy footprint of produced water management in New Mexico

    Science.gov (United States)

    Zemlick, Katie; Kalhor, Elmira; Thomson, Bruce M.; Chermak, Janie M.; Sullivan Graham, Enid J.; Tidwell, Vincent C.

    2018-02-01

    Hydraulic fracturing (HF) and horizontal drilling have revolutionized the fossil fuel industry by enabling production from unconventional oil and gas (UOG) reserves. However, UOG development requires large volumes of water, and subsequent oil and gas production from both conventional and unconventional wells generate large volumes of produced water (PW). While PW is usually considered a waste product, its reuse may lessen demand for freshwater supplies, reduce costs for transportation and disposal, and reduce the risks for injection-induced seismicity. Whether this water is disposed of or treated and reused, both methods require significant amounts of energy. The objective of this study was to identify the primary energy demands of alternative water management strategies, and to characterize and quantify their geographic variability in four oil and gas producing basins in New Mexico using a single year of production. Results illustrate the importance of each component of each produced water management strategy in determining its total energy footprint. Based on 2015 production and water use data, the energy to extract fresh groundwater for hydraulic fracturing (34 GWh-th yr-1.) exceeds the energy that would be required if the same volume of PW were treated chemically (19 GWh-th yr-1.). In addition, the energy required to transport fresh water and dispose of PW (167 GWh-th yr-1.) is far greater than that required to move treated PW (8 GWh-th yr-1.) to a point of reuse. Furthermore, transportation distances, which contribute significantly to the total energy footprint of a given management strategy, are underestimated by nearly 50% state-wide. This indicates that reuse may be an even more energy efficient way to manage PW, even with energy-intensive treatment strategies like electrocoagulation. Reuse of PW for HF is not only more energy efficient than conventional management techniques, it also reduces both demand for scarce fresh water resources and

  19. Sulphur sales should bear processing cost

    Energy Technology Data Exchange (ETDEWEB)

    Jones, W

    1969-01-20

    In this analysis, all the pertinent costs of processing sulfur from sour gas are allocated to one item, the sulfur produced from the sour gas. Therefore, in the graphical representations, the sour gas fed to the amine unit was considered to be dry sour gas containing no carbon dioxide. Cases were considered for increasing percentages of hydrogen sulfide. Costs of amine units and sulfur units were estimated and updated from the literature both for capital investment and operating costs for plants sized to produce sulfur at rates ranging from 20 to 500 long tons per day. The figures shown on the graph for unit costs confirm that the sulfur industry in W. Canada has been selling its sulfur below cost until recently. The conditioning of the natural gas bore the cost of producing sulfur, a sign of unhealthy sulfur markets. Producers would be wise to replenish their sulfur stockpiles to obtain stable marketing conditions at good prices.

  20. Automated disposal of produced water from a coalbed methane well field, a case history

    International Nuclear Information System (INIS)

    Luckianow, B.J.; Findley, M.L.; Paschal, W.T.

    1994-01-01

    This paper provides an overview of the automated disposal system for produced water designed and operated by Taurus Exploration, Inc. This presentation draws from Taurus' case study in the planning, design, construction, and operation of production water disposal facilities for the Mt. Olive well field, located in the Black Warrior Basin of Alabama. The common method for disposing of water produced from coalbed methane wells in the Warrior Basin is to discharge into a receiving stream. The limiting factor in the discharge method is the capability of the receiving stream to assimilate the chloride component of the water discharged. During the winter and spring, the major tributaries of the Black Warrior River are capable of assimilating far more production water than operations can generate. During the summer and fall months, however, these same tributaries can approach near zero flow, resulting in insufficient flow for dilution. During such periods pumping shut-down within the well field can be avoided by routing production waters into a storage facility. This paper discusses the automated production water disposal system on Big Sandy Creek designed and operated by Taurus. This system allows for continuous discharge to the receiving stream, thus taking full advantage of Big Sandy Creek's assimilative capacity, while allowing a provision for excess produced water storage and future stream discharge

  1. Using coal mine saline water to produce chlorine

    Energy Technology Data Exchange (ETDEWEB)

    Gnot, W; Turek, M; Walburg, Z

    1979-01-01

    Utilizing hard coal mine waters with salt concentration reaching 140 kg/mat3 in the chemical industry would significantly reduce the cost of protecting the natural environment from salt. The Institute of Chemistry and Inorganic Technology of the Silesian Technical University in Gliwice developed an efficient technology of producing chorine from underground black coal mine waters. A scheme of the technology is explained: double stage brine purification with magnesium hydroxide as by-product. During the first stage magnesium is precipitated using sodium hydroxide; after increasing salt content in the brine calcium and a low percentage of magnesium are removed by lye-sodium method. During the second stage sedimentation rate increases to 1.4 mm/s, and volume of sludge is only 1%. Magnesium hydroxide is removed using a method patented in Poland (after adding a flocculant magnesium hydroxide is left untouched). Only at a later stage does sedimentation occur. The proposed technology of utilizing mine water will be tested in an experimental plant which will be built at the Ziemowit black coal mine. (7 refs.) (In Polish)

  2. Dispersed droplet dynamics during produced water treatment in oil industry

    NARCIS (Netherlands)

    van Eijkeren, D.F.

    2016-01-01

    For Lagrangian particle tracking applied to swirling flow produced water treatment the influence of the history force is investigated. In the expression for the history force an existing Reynolds number dependent kernel is adapted and validated for a range of experimental data for settling spheres.

  3. Managing produced water from coal seam gas projects: implications for an emerging industry in Australia.

    Science.gov (United States)

    Davies, Peter J; Gore, Damian B; Khan, Stuart J

    2015-07-01

    This paper reviews the environmental problems, impacts and risks associated with the generation and disposal of produced water by the emerging coal seam gas (CSG) industry and how it may be relevant to Australia and similar physical settings. With only limited independent research on the potential environmental impacts of produced water, is it necessary for industry and government policy makers and regulators to draw upon the experiences of related endeavours such as mining and groundwater extraction accepting that the conclusions may not always be directly transferrable. CSG is widely touted in Australia as having the potential to provide significant economic and energy security benefits, yet the environmental and health policies and the planning and regulatory setting are yet to mature and are continuing to evolve amidst ongoing social and environmental concerns and political indecision. In this review, produced water has been defined as water that is brought to the land surface during the process of recovering methane gas from coal seams and includes water sourced from CSG wells as well as flowback water associated with drilling, hydraulic fracturing and gas extraction. A brief overview of produced water generation, its characteristics and environmental issues is provided. A review of past lessons and identification of potential risks, including disposal options, is included to assist in planning and management of this industry.

  4. Producing a problem? Effects of produced water contaminants (PAHs, radium-226, barium and scale inhibitor) on the copepod Calanus finmarchicus

    Energy Technology Data Exchange (ETDEWEB)

    Kiel Jensen, Louise [Norwegian Radiation Protection Authority, Fram Centre, 9296 Tromsoe (Norway); Halvorsen, Elisabeth; Gammelsaeter Hallanger, Ingeborg [UiT The Arctic University of Norway, Department of Arctic and Marine Biology, P.O. box 6050 Langnes, 9037 Tromsoe (Norway); Tollefsen, Knut Erik; Brooks, Steven [Norwegian Institute for Water Research, Gaustadalleen 21, 0349 Oslo (Norway); Hansen, Bjoern Henrik [SINTEF Materials and Chemistry, Marine Environmental Technology, Brattoerkaia 17B, 7010 Trondheim (Norway)

    2014-07-01

    In the Barents Sea region new petroleum fields are discovered yearly and the extraction of petroleum products are expected to increase in the upcoming years. Despite enhanced technology and stricter governmental legislation, establishing the petroleum industry in the Barents Sea will introduce a new source of Naturally Occurring Radioactive Material (NORM) to the area as some discharges of produced water will be allowed. Whether the presence of produced water poses a risk to the Arctic marine life remains to be examined. We examined effects on the copepod species Calanus finmarchicus after exposure to several compounds found in produced water. A mixture of polycyclic aromatic hydrocarbons and alkyl phenols commonly found in produced water was used as a proxy of the organic fraction of the produced water (hereafter termed APW (Artificial Produced Water)). In addition, exposures were done using radium-226 (proxy for NORM), barium (proxy for metals) and a scale inhibitor (SI -4470, M-I SWACO, Schlumberger Norge AS). Short-term screening tests on a range of concentrations of all compounds were run to assess the hatchability of the eggs and early survival of the nauplii. Long-term experiments were carried out with exposure concentrations at realistic levels found in the vicinity of known discharge points. The copepod C. finmarchicus is considered a keystone species in the Barents Sea ecosystem as it represents the major pathway of energy transfer from lower to higher trophic levels. We have examined sub-lethal effects on early life stages and on adult females. The hatchability of the eggs was not affected by concentrations well above realistic environmental levels. However, the instant mortality of the hatched larvae increased with higher concentrations of barium, scale inhibitor and APW, though not with higher radium-226 concentration. When examining the long-term growth of the nauplii, we found that the survival was poor in the APW treatment, and in the barium

  5. Characterization of N-Acylhomoserine Lactones Produced by Bacteria Isolated from Industrial Cooling Water Systems

    Directory of Open Access Journals (Sweden)

    Noriya Okutsu

    2015-12-01

    Full Text Available The cooling water systems are used to remove heat generated in the various industries. Biofouling of the cooling water systems causes blocking of condenser pipes and the heat exchanger tubes. In many Gram-negative bacteria, N-acylhomoserine lactone (AHL are used as quorum-sensing signal molecule and associated with biofilm formation. To investigate the relationship between quorum sensing and biofouling in the cooling water system, we isolated a total of 192 bacterial strains from the five cooling water systems, and screened for AHL production. Seven isolates stimulated AHL-mediated purple pigment production in AHL reporter strain Chromobacterium violaceum CV026 or VIR07. Based on their 16S rRNA gene sequences, AHL-producing isolates were assigned to Aeromonas hydrophila, Lysobacter sp., Methylobacterium oryzae, and Bosea massiliensis. To the best of our knowledge, B. massiliensis and Lysobacter sp. have not been reported as AHL-producing species in the previous researches. AHLs extracted from the culture supernatants of B. massiliensis and Lysobacter sp. were identified by liquid chromatography-mass spectrometry. AHLs produced by B. massiliensis were assigned as N-hexanoyl-l-homoserine lactone (C6-HSL, N-(3-oxohexanoyl-l-homoserine lactone (3-oxo-C6-HSL, and N-(3-oxooctanoyl-l-homoserine lactone (3-oxo-C8-HSL. AHLs produced by Lysobacter sp. were assigned as N-decanoyl-l-homoserine lactone (C10-HSL and N-(3-oxodecanoyl-l-homoserine lactone (3-oxo-C10-HSL. This is the first report of identification of AHLs produced by B. massiliensis and Lysobacter sp. isolated from the cooling water system.

  6. Produced water ponds are an important source of aromatics and alcohols in Rocky Mountain oil and gas basins

    Science.gov (United States)

    Lyman, S. N.

    2017-12-01

    Most of the water extracted with oil and natural gas (i.e., produced water) is disposed of by injection into the subsurface. In the arid western United States, however, a significant portion of produced water is discharged in ponds for evaporative disposal, and produced water is often stored in open ponds prior to subsurface injection. Even though they are common in the West (Utah's Uinta Basin has almost 200 ha), produced water ponds have been excluded from oil and gas emissions inventories because little information about their emission rates and speciation is available. We used flux chambers and inverse plume modeling to measure emissions of methane, C2-C11 hydrocarbons, light alcohols, carbonyls, and carbon dioxide from oil and gas produced water storage and disposal ponds in the Uinta Basin and the Upper Green River Basin, Wyoming, during 2013-2017. Methanol was the most abundant organic compound in produced water (91 ± 2% of the total volatile organic concentration; mean ± 95% confidence interval) but accounted for only 25 ± 30% of total organic compound emissions from produced water ponds. Non-methane hydrocarbons, especially C6-C9 alkanes and aromatics, accounted for the majority of emitted organics. We were able to predict emissions of individual compounds based on water concentrations, but only to within an order of magnitude. The speciation and magnitude of emissions varied strongly across facilities and was influenced by water age, the presence or absence of oil sheens, and with meteorological conditions (especially ice cover). Flux chamber measurements were lower than estimates from inverse modeling techniques.Based on our flux chamber measurements, we estimate that produced water ponds are responsible for between 3 and 9% of all non-methane organic compound emissions in the Uinta Basin (or as much as 18% if we rely on our inverse modeling results). Emissions from produced water ponds contain little methane and are more reactive (i.e., they have

  7. Evaluation of membranes for the treatment of oilfield-produced water

    Directory of Open Access Journals (Sweden)

    Silvio Edegar Weschenfelder

    2015-04-01

    Full Text Available Large quantities of water are generated during oil extraction. Reinjection of this effluent is frequently the most suitable option for environmental considerations. For this purpose, the water produced must have characteristics that will prevent the plugging of the reservoir rocks, i.e., suspended solids and oil and grease content must be lower than 5 mg L-1. This work evaluated the performance of membranes for water treatment, based upon long-term experiments with real effluent, evaluating the permeate flux over time and the effluent characteristics. The results indicated that it is possible to obtain a permeate flux with suspended solids content with less than 1 mg L-1 oil and a grease concentration in the range of 1 to 3 mg L-1 using membranes with a pore size of 0,1 m. After 50 hours of permeation, the permeate fluxes obtained with the polymeric and ceramic membranes were equal to 50 and 300 L h-1 m-2, respectively. With a chemical regeneration procedure, it was possible to recover 95% of the ceramic membrane’s original permeability and 30% of the polymeric membrane’s permeability. Considering the permeate quality, the regeneration efficiency of the membrane and the fluxes achieved, it is possible to point out the use of ceramic membranes as a potential technology for treating oilfield-produced water, and it has the advantage of being a compact and robust process.

  8. Hydrogen generation from water using Mg nanopowder produced by arc plasma method

    Directory of Open Access Journals (Sweden)

    Masahiro Uda, Hideo Okuyama, Tohru S Suzuki and Yoshio Sakka

    2012-01-01

    Full Text Available We report that hydrogen gas can be easily produced from water at room temperature using a Mg nanopowder (30–1000 nm particles, average diameter 265 nm. The Mg nanopowder was produced by dc arc melting of a Mg ingot in a chamber with mixed-gas atmosphere (20% N2–80% Ar at 0.1 MPa using custom-built nanopowder production equipment. The Mg nanopowder was passivated with a gas mixture of 1% O2 in Ar for 12 h in the final step of the synthesis, after which the nanopowder could be safely handled in ambient air. The nanopowder vigorously reacted with water at room temperature, producing 110 ml of hydrogen gas per 1 g of powder in 600 s. This amount corresponds to 11% of the hydrogen that could be generated by the stoichiometric reaction between Mg and water. Mg(OH2 flakes formed on the surface of the Mg particles as a result of this reaction. They easily peeled off, and the generation of hydrogen continued until all the Mg was consumed.

  9. Irrigation water sources and irrigation application methods used by U.S. plant nursery producers

    Science.gov (United States)

    Paudel, Krishna P.; Pandit, Mahesh; Hinson, Roger

    2016-02-01

    We examine irrigation water sources and irrigation methods used by U.S. nursery plant producers using nested multinomial fractional regression models. We use data collected from the National Nursery Survey (2009) to identify effects of different firm and sales characteristics on the fraction of water sources and irrigation methods used. We find that regions, sales of plants types, farm income, and farm age have significant roles in what water source is used. Given the fraction of alternative water sources used, results indicated that use of computer, annual sales, region, and the number of IPM practices adopted play an important role in the choice of irrigation method. Based on the findings from this study, government can provide subsidies to nursery producers in water deficit regions to adopt drip irrigation method or use recycled water or combination of both. Additionally, encouraging farmers to adopt IPM may enhance the use of drip irrigation and recycled water in nursery plant production.

  10. Microbiological effectiveness of locally produced ceramic filters for drinking water treatment in Cambodia.

    Science.gov (United States)

    Brown, Joe; Sobsey, Mark D

    2010-03-01

    Low-cost options for the treatment of drinking water at the household level are being explored by the Cambodian government and non-governmental organizations (NGOs) working in Cambodia, where many lack access to improved drinking water sources and diarrhoeal diseases are the most prevalent cause of death in children under 5 years of age. The ceramic water purifier (CWP), a locally produced, low-cost ceramic filter, is now being implemented by several NGOs, and an estimated 100,000+households in the country now use them for drinking water treatment. Two candidate filters were tested for the reduction of bacterial and viral surrogates for waterborne pathogens using representative Cambodian drinking water sources (rainwater and surface water) spiked with Escherichia coli and bacteriophage MS2. Results indicate that filters were capable of reducing key microbes in the laboratory with mean reductions of E. coli of approximately 99% and mean reduction of bacteriophages of 90-99% over >600 litres throughput. Increased effectiveness was not observed in filters with an AgNO3 amendment. At under US$10 per filter, locally produced ceramic filters may be a promising option for drinking water treatment and safe storage at the household level.

  11. Managing flowback and produced water from hydraulic fracturing under stochastic environment

    Science.gov (United States)

    Zhang, X.; Sun, A. Y.; Duncan, I. J.; Vesselinov, V. V.

    2017-12-01

    A large volume of wastewater is being generated from hydraulic fracturing in shale gas plays, including flowback and produced water. The produced wastewater in terms of its quantity and quality has become one of the main environmental problems facing shale gas industries worldwide. Cost-effective planning and management of flowback and produced water is highly desirable. Careful choice of treatment, disposal, and reuse options can lower costs and reduce potential environmental impacts. To handle the recourse issue in decision-making, a two-stage stochastic management model is developed to provide optimal alternatives for fracturing wastewater management. The proposed model is capable of prompting corrective actions to allow decision makers to adjust the pre-defined management strategies. By using this two-stage model, potential penalties arising from decision infeasibility can be minimized. The applicability of the proposed model is demonstrated using a representative synthetic example, in which tradeoffs between economic and environmental goals are quantified. This approach can generate informed defensible decisions for shale gas wastewater management. In addition, probabilistic and non-probabilistic uncertainties are effectively addressed.

  12. How to quench your thirst. The effect of water-based products varying in temperature and texture, flavour, and sugar content on thirst

    NARCIS (Netherlands)

    Belzen, van L.; Postma, E.M.; Postma, E.M.; Postma, E.M.; Boesveldt, S.

    2017-01-01

    The sensation of thirst plays an important role in the consumption of water or other fluids to rehydrate the body in order to keep bodily functions working properly. An increase in saliva secretion, wetting the mouth by ingestion of liquids, and cooling and sour components in products can alleviate

  13. Evaluating the U.S. Food Safety Modernization Act Produce Safety Rule Standard for Microbial Quality of Agricultural Water for Growing Produce

    NARCIS (Netherlands)

    Havelaar, Arie H; Vazquez, Kathleen M; Topalcengiz, Zeynal; Muñoz-Carpena, Rafael; Danyluk, Michelle D

    2017-01-01

    The U.S. Food and Drug Administration (FDA) has defined standards for the microbial quality of agricultural surface water used for irrigation. According to the FDA produce safety rule (PSR), a microbial water quality profile requires analysis of a minimum of 20 samples for Escherichia coli over 2 to

  14. Fuzzy rule-based modelling for human health risk from naturally occurring radioactive materials in produced water

    International Nuclear Information System (INIS)

    Shakhawat, Chowdhury; Tahir, Husain; Neil, Bose

    2006-01-01

    Produced water, discharged from offshore oil and gas operations, contains chemicals from formation water, condensed water, and any chemical added down hole or during the oil/water separation process. Although, most of the contaminants fall below the detection limits within a short distance from the discharge port, a few of the remaining contaminants including naturally occurring radioactive materials (NORM) are of concern due to their bioavailability in the media and bioaccumulation characteristics in finfish and shellfish species used for human consumption. In the past, several initiatives have been taken to model human health risk from NORM in produced water. The parameters of the available risk assessment models are imprecise and sparse in nature. In this study, a fuzzy possibilistic evaluation using fuzzy rule based modeling has been presented. Being conservative in nature, the possibilistic approach considers possible input parameter values; thus provides better environmental prediction than the Monte Carlo (MC) calculation. The uncertainties of the input parameters were captured with fuzzy triangular membership functions (TFNs). Fuzzy if-then rules were applied for input concentrations of two isotopes of radium, namely 226 Ra, and 228 Ra, available in produced water and bulk dilution to evaluate the radium concentration in fish tissue used for human consumption. The bulk dilution was predicted using four input parameters: produced water discharge rate, ambient seawater velocity, depth of discharge port and density gradient. The evaluated cancer risk shows compliance with the regulatory guidelines; thus minimum risk to human health is expected from NORM components in produced water

  15. Multidrug resistance found in extended-spectrum beta-lactamase-producing Enterobacteriaceae from rural water reservoirs in Guantao, China

    Directory of Open Access Journals (Sweden)

    Hongna eZhang

    2015-03-01

    Full Text Available Extended-spectrum beta-lactamase (ESBL-producing Enterobacteriaceae have been isolated from humans and animals across the world. However, data on prevalence of ESBL-producing Enterobacteriaceae from rural water reservoirs is limited. This study aimed to isolate and characterize ESBL-producing Enterobacteriaceae in rural water reservoirs in Guantao, China. ESBL-producing Enterobacteriaceae were found in 5 (16.7% of 30 sampled rural water reservoirs. 66 individual isolates expressing an ESBL phenotype were obtained in the present study. Species identification showed that 42 representatives of Escherichia coli, 17 Klebsiella pneumoniae, 4 Raoultella planticola, and 3 Enterobacter cloacae. 20 isolates contained a single bla gene, including CTX-M (17 strains, TEM (2 strains, and SHV (1 strain. 46 isolates contained more than one type of beta-lactamase genes. ESBL-producing Enterobacteriaceae isolated in this study were all multidrug resistant. These findings indicated that the seroius contamination of ESBL-producing Enterobacteriaceae in rural water resevoirs existed in Guantao, China.

  16. Air emissions from sour-gas processing plants and dairy-cattle reproduction in Alberta, Canada.

    Science.gov (United States)

    Scott, H M; Soskolne, C L; Martin, S W; Shoukri, M M; Lissemore, K D; Coppock, R W; Guidotti, T L

    2003-02-15

    The dispersion of air pollutants from all 231 licensed sour-gas processing plants in Alberta, Canada, was modeled on a monthly basis over a 10-year period (1985-1994). Exposure estimates for sulfur dioxide (SO(2)-used as a surrogate for exposure to combusted emissions) then were assigned to 1382 provincial dairy farms using a geographical-information system. Individual average and peak exposure for periods prior to each of 15 months of age and conception (four exposure-averaging periods for each of two dispersion models) were estimated for 163,988 primiparous female dairy-cattle between 1986 and 1994. Monthly or annual average farm-site exposure estimates likewise were assigned to associated herd-level data sets for the biologically relevant period of interest for each of three additional reproductive outcomes: monthly herd-average calving interval, stillbirth risk, and twinning risk. In one of the main-effects models, the maximum (i.e., peak) monthly sour-gas exposure experienced by individual-animals from birth to conception was associated with an increased time to first-calving in the very-highest exposure category (hazard ratio=0.86, 95% CI=0.80, 0.92). This equates to a decreased hazard (lambda) of calving (in each month subsequent to 22 months of age) for the highest-exposure animals (lambda=0.170) versus the zero-exposure animals (lambda=0.198) in a model with referent values for agro-ecological region and season of birth. The dose-response was not consistent across the full range of exposure categories. There was significant (P=0.003) interaction of emissions with agro-ecological region. After accounting for the interaction, a more-consistent dose-response was evident for some (but not all) agro-ecological regions. This suggests that any effect of emissions on dairy-heifer reproduction is subject to modification by features of soil type, vegetative cover, and/or climate. The increase in monthly herd-average calving interval on farms exposed to the very

  17. Process Design and Techno-economic Analysis for Materials to Treat Produced Waters.

    Energy Technology Data Exchange (ETDEWEB)

    Heimer, Brandon Walter [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Paap, Scott M [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sasan, Koroush [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Brady, Patrick Vane. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Nenoff, Tina M. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2017-09-01

    Significant quantities of water are produced during enhanced oil recovery making these “produced water” streams attractive candidates for treatment and reuse. However, high concentrations of dissolved silica raise the propensity for fouling. In this paper, we report the design and economic analysis for a new ion exchange process using calcined hydrotalcite (HTC) to remove silica from water. This process improves upon known technologies by minimizing sludge product, reducing process fouling, and lowering energy use. Process modeling outputs included raw material requirements, energy use, and the minimum water treatment price (MWTP). Monte Carlo simulations quantified the impact of uncertainty and variability in process inputs on MWTP. These analyses showed that cost can be significantly reduced if the HTC materials are optimized. Specifically, R&D improving HTC reusability, silica binding capacity, and raw material price can reduce MWTP by 40%, 13%, and 20%, respectively. Optimizing geographic deployment further improves cost competitiveness.

  18. Cloning, Expression, and Characterization of Sorbitol Transporters from Developing Sour Cherry Fruit and Leaf Sink Tissues1

    Science.gov (United States)

    Gao, Zhifang; Maurousset, Laurence; Lemoine, Remi; Yoo, Sang-Dong; van Nocker, Steven; Loescher, Wayne

    2003-01-01

    The acyclic polyol sorbitol is a primary photosynthetic product and the principal photosynthetic transport substance in many economically important members of the family Rosaceace (e.g. almond [Prunus dulcis (P. Mill.) D.A. Webber], apple [Malus pumila P. Mill.], cherry [Prunus spp.], peach [Prunus persica L. Batsch], and pear [Pyrus communis]). To understand key steps in long-distance transport and particularly partitioning and accumulation of sorbitol in sink tissues, we have cloned two sorbitol transporter genes (PcSOT1 and PcSOT2) from sour cherry (Prunus cerasus) fruit tissues that accumulate large quantities of sorbitol. Sorbitol uptake activities and other characteristics were measured by heterologous expression of PcSOT1 and PcSOT2 in yeast (Saccharomyces cerevisiae). Both genes encode proton-dependent, sorbitol-specific transporters with similar affinities (Km sorbitol of 0.81 mm for PcSOT1 and 0.64 mm for PcSOT2). Analyses of gene expression of these transporters, however, suggest different roles during leaf and fruit development. PcSOT1 is expressed throughout fruit development, but especially when growth and sorbitol accumulation rates are highest. In leaves, PcSOT1 expression is highest in young, expanding tissues, but substantially less in mature leaves. In contrast, PcSOT2 is mainly expressed only early in fruit development and not in leaves. Compositional analyses suggest that transport mediated by PcSOT1 and PcSOT2 plays a major role in sorbitol and dry matter accumulation in sour cherry fruits. Presence of these transporters and the high fruit sorbitol concentrations suggest that there is an apoplastic step during phloem unloading and accumulation in these sink tissues. Expression of PcSOT1 in young leaves before completion of the transition from sink to source is further evidence for a role in determining sink activity. PMID:12692316

  19. Pilot scale test of a produced water-treatment system for initial removal of organic compounds

    Energy Technology Data Exchange (ETDEWEB)

    Sullivan, Enid J [Los Alamos National Laboratory; Kwon, Soondong [UT-AUSTIN; Katz, Lynn [UT-AUSTIN; Kinney, Kerry [UT-AUSTIN

    2008-01-01

    A pilot-scale test to remove polar and non-polar organics from produced water was performed at a disposal facility in Farmington NM. We used surfactant-modified zeolite (SMZ) adsorbent beds and a membrane bioreactor (MBR) in combination to reduce the organic carbon content of produced water prior to reverse osmosis (RO). Reduction of total influent organic carbon (TOC) to 5 mg/L or less is desirable for efficient RO system operation. Most water disposed at the facility is from coal-bed gas production, with oil production waters intermixed. Up to 20 gal/d of produced water was cycled through two SMZ adsorbent units to remove volatile organic compounds (BTEX, acetone) and semivolatile organic compounds (e.g., napthalene). Output water from the SMZ units was sent to the MBR for removal of the organic acid component of TOC. Removal of inorganic (Mn and Fe oxide) particulates by the SMZ system was observed. The SMZ columns removed up to 40% of the influent TOC (600 mg/L). BTEX concentrations were reduced from the initial input of 70 mg/L to 5 mg/L by the SMZ and to an average of 2 mg/L after the MBR. Removal rates of acetate (input 120-170 mg/L) and TOC (input up to 45 mg/L) were up to 100% and 92%, respectively. The water pH rose from 8.5 to 8.8 following organic acid removal in the MBR; this relatively high pH was likely responsible for observed scaling of the MBR internal membrane. Additional laboratory studies showed the scaling can be reduced by metered addition of acid to reduce the pH. Significantly, organic removal in the MBR was accomplished with a very low biomass concentration of 1 g/L throughout the field trial. An earlier engineering evaluation shows produced water treatment by the SMZ/MBR/RO system would cost from $0.13 to $0.20 per bbl at up to 40 gpm. Current estimated disposal costs for produced water are $1.75 to $4.91 per bbl when transportation costs are included, with even higher rates in some regions. Our results suggest that treatment by an SMZ

  20. Effect of Disinfectants on Preventing the Cross-Contamination of Pathogens in Fresh Produce Washing Water

    NARCIS (Netherlands)

    Banach, J.L.; Sampers, I.; Haute, van S.; Fels, van der H.J.

    2015-01-01

    The potential cross-contamination of pathogens between clean and contaminated produce in the washing tank is highly dependent on the water quality. Process wash water disinfectants are applied to maintain the water quality during processing. The review examines the efficacy of process wash water

  1. Effect of Disinfectants on Preventing the Cross-Contamination of Pathogens in Fresh Produce Washing Water

    Directory of Open Access Journals (Sweden)

    Jennifer L. Banach

    2015-07-01

    Full Text Available The potential cross-contamination of pathogens between clean and contaminated produce in the washing tank is highly dependent on the water quality. Process wash water disinfectants are applied to maintain the water quality during processing. The review examines the efficacy of process wash water disinfectants during produce processing with the aim to prevent cross-contamination of pathogens. Process wash water disinfection requires short contact times so microorganisms are rapidly inactivated. Free chlorine, chlorine dioxide, ozone, and peracetic acid were considered suitable disinfectants. A disinfectant’s reactivity with the organic matter will determine the disinfectant residual, which is of paramount importance for microbial inactivation and should be monitored in situ. Furthermore, the chemical and worker safety, and the legislative framework will determine the suitability of a disinfection technique. Current research often focuses on produce decontamination and to a lesser extent on preventing cross-contamination. Further research on a sanitizer’s efficacy in the washing water is recommended at the laboratory scale, in particular with experimental designs reflecting industrial conditions. Validation on the industrial scale is warranted to better understand the overall effects of a sanitizer.

  2. Effect of Disinfectants on Preventing the Cross-Contamination of Pathogens in Fresh Produce Washing Water

    Science.gov (United States)

    Banach, Jennifer L.; Sampers, Imca; Van Haute, Sam; van der Fels-Klerx, H.J. (Ine)

    2015-01-01

    The potential cross-contamination of pathogens between clean and contaminated produce in the washing tank is highly dependent on the water quality. Process wash water disinfectants are applied to maintain the water quality during processing. The review examines the efficacy of process wash water disinfectants during produce processing with the aim to prevent cross-contamination of pathogens. Process wash water disinfection requires short contact times so microorganisms are rapidly inactivated. Free chlorine, chlorine dioxide, ozone, and peracetic acid were considered suitable disinfectants. A disinfectant’s reactivity with the organic matter will determine the disinfectant residual, which is of paramount importance for microbial inactivation and should be monitored in situ. Furthermore, the chemical and worker safety, and the legislative framework will determine the suitability of a disinfection technique. Current research often focuses on produce decontamination and to a lesser extent on preventing cross-contamination. Further research on a sanitizer’s efficacy in the washing water is recommended at the laboratory scale, in particular with experimental designs reflecting industrial conditions. Validation on the industrial scale is warranted to better understand the overall effects of a sanitizer. PMID:26213953

  3. Increasing of the processing capacity of an alkanoamine in aqueous solution mixed sour gas treatment unit; Incremento de la capacidad de procesamiento de una planta de tratamiento de gas amargo con mezclas de alcanolaminas en solucion acuosa

    Energy Technology Data Exchange (ETDEWEB)

    Bernal, J. Manuel; Valtierra, Victor H.; Cabrales, Alberto [Instituto Mexicano del Petroleo, Mexico City (Mexico)

    1998-07-01

    The necessity of increasing the process capacity of the existing sour gas treating units, has been a factor that has driven the investigation centers to develop new solvent formulations that could been capable of removing the sour gases without majors changes in the equipment that conforms those units. In this sense, the Instituto Mexicano del Petroleo has carried out the study in order to increase the processing capacity of a sour gas treatment plant of Petroleos Mexicanos. In this work, the use of solvents or alternative formulations, based on the use of methyl-diethanolamine (MDEA), as single solvent, or in mixture with others are considered. Our experimental data indicates that the use of MDEA in a formulation, in mixture with another amines, carry out to combination of attributes such as high absorption capacity and a high speed of absorption of the preferred acid gas (H{sub 2}S), besides it reduces the degradation index of the solvent and minimizes the equipment corrosion situation that is transformed in considerable improvement in the processing capacity and/or in the energy process savings, finally the operative problems are minimized. (author)

  4. A review of environmental impacts of salts from produced waters on aquatic resources

    Science.gov (United States)

    Farag, Aïda M.; Harper, David D.

    2014-01-01

    Salts are frequently a major constituent of waste waters produced during oil and gas production. These produced waters or brines must be treated and/or disposed and provide a daily challenge for operators and resource managers. Some elements of salts are regulated with water quality criteria established for the protection of aquatic wildlife, e.g. chloride (Cl−), which has an acute standard of 860 mg/L and a chronic standard of 230 mg/L. However, data for establishing such standards has only recently been studied for other components of produced water, such as bicarbonate (HCO3−), which has acute median lethal concentrations (LC50s) ranging from 699 to > 8000 mg/L and effects on chronic toxicity from 430 to 657 mg/L. While Cl− is an ion of considerable importance in multiple geographical regions, knowledge about the effects of hardness (calcium and magnesium) on its toxicity and about mechanisms of toxicity is not well understood. A multiple-approach design that combines studies of both individuals and populations, conducted both in the laboratory and the field, was used to study toxic effects of bicarbonate (as NaHCO3). This approach allowed interpretations about mechanisms related to growth effects at the individual level that could affect populations in the wild. However, additional mechanistic data for HCO3−, related to the interactions of calcium (Ca2 +) precipitation at the microenvironment of the gill would dramatically increase the scientific knowledge base about how NaHCO3 might affect aquatic life. Studies of the effects of mixtures of multiple salts present in produced waters and more chronic effect studies would give a better picture of the overall potential toxicity of these ions. Organic constituents in hydraulic fracturing fluids, flowback waters, etc. are a concern because of their carcinogenic properties and this paper is not meant to minimize the importance of maintaining vigilance with respect to potential organic contamination.

  5. Factors affecting the porridge-making quality in South African sorghums

    CSIR Research Space (South Africa)

    Taylor, JRN

    1997-04-01

    Full Text Available fermented, sour porridges remain popular, particularly among the Tswana of Botswana and South Africa (Novellie 1982; Sooliman 1993) The production of sorghum porridge involves ?rst producing a meal from sorghum grain. Commercially, this is generally done..., South Africa. the remaining part of the kernel (essentially endosperm) into a coarse meal. Alternatively, endosperm meal can be produced directly from grain by roller milling (Munck 1995). The meal is then cooked with boiling water into a porridge...

  6. Molecular- and cultivation-based analyses of microbial communities in oil field water and in microcosms amended with nitrate to control H{sub 2}S production

    Energy Technology Data Exchange (ETDEWEB)

    Kumaraswamy, Raji; Ebert, Sara; Fedorak, Phillip M.; Foght, Julia M. [Alberta Univ., Edmonton, AB (Canada). Biological Sciences; Gray, Murray R. [Alberta Univ., Edmonton, AB (Canada). Chemical and Materials Engineering

    2011-03-15

    Nitrate injection into oil fields is an alternative to biocide addition for controlling sulfide production ('souring') caused by sulfate-reducing bacteria (SRB). This study examined the suitability of several cultivation-dependent and cultivation-independent methods to assess potential microbial activities (sulfidogenesis and nitrate reduction) and the impact of nitrate amendment on oil field microbiota. Microcosms containing produced waters from two Western Canadian oil fields exhibited sulfidogenesis that was inhibited by nitrate amendment. Most probable number (MPN) and fluorescent in situ hybridization (FISH) analyses of uncultivated produced waters showed low cell numbers ({<=}10{sup 3} MPN/ml) dominated by SRB (>95% relative abundance). MPN analysis also detected nitrate-reducing sulfide-oxidizing bacteria (NRSOB) and heterotrophic nitrate-reducing bacteria (HNRB) at numbers too low to be detected by FISH or denaturing gradient gel electrophoresis (DGGE). In microcosms containing produced water fortified with sulfate, near-stoichiometric concentrations of sulfide were produced. FISH analyses of the microcosms after 55 days of incubation revealed that Gammaproteobacteria increased from undetectable levels to 5-20% abundance, resulting in a decreased proportion of Deltaproteobacteria (50-60% abundance). DGGE analysis confirmed the presence of Delta- and Gammaproteobacteria and also detected Bacteroidetes. When sulfate-fortified produced waters were amended with nitrate, sulfidogenesis was inhibited and Deltaproteobacteria decreased to levels undetectable by FISH, with a concomitant increase in Gammaproteobacteria from below detection to 50-60% abundance. DGGE analysis of these microcosms yielded sequences of Gamma- and Epsilonproteobacteria related to presumptive HNRB and NRSOB (Halomonas, Marinobacterium, Marinobacter, Pseudomonas and Arcobacter), thus supporting chemical data indicating that nitrate-reducing bacteria out-compete SRB when nitrate is

  7. Treatment of oilfield produced water by anaerobic process coupled with micro-electrolysis.

    Science.gov (United States)

    Li, Gang; Guo, Shuhai; Li, Fengmei

    2010-01-01

    Treatment of oilfield produced water was investigated using an anaerobic process coupled with micro-electrolysis (ME), focusing on changes in chemical oxygen demand (COD) and biodegradability. Results showed that COD exhibited an abnormal change in the single anaerobic system in which it increased within the first 168 hr, but then decreased to 222 mg/L after 360 hr. The biological oxygen demand (five-day) (BODs)/COD ratio of the water increased from 0.05 to 0.15. Hydrocarbons in the wastewater, such as pectin, degraded to small molecules during the hydrolytic acidification process. Comparatively, the effect of ME was also investigated. The COD underwent a slight decrease and the BOD5/COD ratio of the water improved from 0.05 to 0.17 after ME. Removal of COD was 38.3% under the idealized ME conditions (pH 6.0), using iron and active carbon (80 and 40 g/L, respectively). Coupling the anaerobic process with ME accelerated the COD removal ratio (average removal was 53.3%). Gas chromatography/mass spectrometry was used to analyze organic species conversion. This integrated system appeared to be a useful option for the treatment of water produced in oilfields.

  8. Surface modification of cellulose acetate membrane using thermal annealing to enhance produced water treatment

    Energy Technology Data Exchange (ETDEWEB)

    Kusworo, T. D., E-mail: tdkusworo@che.undip.ac.id; Aryanti, N., E-mail: nita.aryanti@gmail.com; Firdaus, M. M. H.; Sukmawati, H. [Chemical Engineering, Faculty of Engineering, Diponegoro University Prof. Soedarto Street, Tembalang, Semarang, 50239, Phone/Fax : (024)7460058 (Indonesia)

    2015-12-29

    This study is performed primarily to investigate the effect of surface modification of cellulose acetate using thermal annealing on the enhancement of membrane performance for produced water treatment. In this study, Cellulose Acetate membranes were casted using dry/wet phase inversion technique. The effect of additive and post-treatment using thermal annealing on the membrane surface were examined for produced water treatment. Therma annealing was subjected to membrane surface at 60 and 70 °C for 5, 10 and 15 second, respectively. Membrane characterizations were done using membrane flux and rejection with produced water as a feed, Scanning Electron Microscopy (SEM) and Fourier Transform Infra Red (FTIR) analysis. Experimental results showed that asymmetric cellulose acetate membrane can be made by dry/wet phase inversion technique. The results from the Scanning Electron Microscopy (FESEM) analysis was also confirmed that polyethylene glycol as additivie in dope solution and thermal annealing was affected the morphology and membrane performance for produced water treatment, respectively. Scanning electron microscopy micrographs showed that the selective layer and the substructure of membrane became denser and more compact after the thermal annealing processes. Therefore, membrane rejection was significantly increased while the flux was slighty decreased, respectively. The best membrane performance is obtained on the composition of 18 wt % cellulose acetate, poly ethylene glycol 5 wt% with thermal annealing at 70° C for 15 second.

  9. Surface modification of cellulose acetate membrane using thermal annealing to enhance produced water treatment

    International Nuclear Information System (INIS)

    Kusworo, T. D.; Aryanti, N.; Firdaus, M. M. H.; Sukmawati, H.

    2015-01-01

    This study is performed primarily to investigate the effect of surface modification of cellulose acetate using thermal annealing on the enhancement of membrane performance for produced water treatment. In this study, Cellulose Acetate membranes were casted using dry/wet phase inversion technique. The effect of additive and post-treatment using thermal annealing on the membrane surface were examined for produced water treatment. Therma annealing was subjected to membrane surface at 60 and 70 °C for 5, 10 and 15 second, respectively. Membrane characterizations were done using membrane flux and rejection with produced water as a feed, Scanning Electron Microscopy (SEM) and Fourier Transform Infra Red (FTIR) analysis. Experimental results showed that asymmetric cellulose acetate membrane can be made by dry/wet phase inversion technique. The results from the Scanning Electron Microscopy (FESEM) analysis was also confirmed that polyethylene glycol as additivie in dope solution and thermal annealing was affected the morphology and membrane performance for produced water treatment, respectively. Scanning electron microscopy micrographs showed that the selective layer and the substructure of membrane became denser and more compact after the thermal annealing processes. Therefore, membrane rejection was significantly increased while the flux was slighty decreased, respectively. The best membrane performance is obtained on the composition of 18 wt % cellulose acetate, poly ethylene glycol 5 wt% with thermal annealing at 70° C for 15 second

  10. Radioactivity in produced water from Norwegian oil and gas installations - concentrations, bioavailability and doses to marine biota

    Energy Technology Data Exchange (ETDEWEB)

    Sidhu, R.; Eriksen, D. Oe.; Straalberg, E.; Iden, K. I.; Rye, H.; Hylland, K.; Ruus, A.; Roeyset, O.; Berntssen, M. H. G.

    2006-03-15

    Substantial amounts of produced water, containing elevated levels of radionuclides (mainly 226Ra and 228Ra) are discharged to the sea as a result of oil and gas production on the Norwegian Continental Shelf. So far no study has assessed the potential radiological effects on marine biota in connection with radionuclide discharges to the North Sea. The main objective of the project is to establish radiological safe discharge limits for radium, lead and polonium associated with other components in produced water from oil and gas installations on the Norwegian continental shelf. Preliminary results indicate that presence of added chemicals such as scale inhibitors in the produced water has a marked influence on the formation of radium and barium sulphates when produced water is mixed with sea water. Thus, the mobility and bio-availability of radium (and barium) may be larger than anticipated. Also, the bio-availability of radium may be increased due to presence of such chemicals, and this is presently being studied. (author) (tk)

  11. Water Bodies’ Mapping from Sentinel-2 Imagery with Modified Normalized Difference Water Index at 10-m Spatial Resolution Produced by Sharpening the SWIR Band

    Directory of Open Access Journals (Sweden)

    Yun Du

    2016-04-01

    Full Text Available Monitoring open water bodies accurately is an important and basic application in remote sensing. Various water body mapping approaches have been developed to extract water bodies from multispectral images. The method based on the spectral water index, especially the Modified Normalized Difference Water Index (MDNWI calculated from the green and Shortwave-Infrared (SWIR bands, is one of the most popular methods. The recently launched Sentinel-2 satellite can provide fine spatial resolution multispectral images. This new dataset is potentially of important significance for regional water bodies’ mapping, due to its free access and frequent revisit capabilities. It is noted that the green and SWIR bands of Sentinel-2 have different spatial resolutions of 10 m and 20 m, respectively. Straightforwardly, MNDWI can be produced from Sentinel-2 at the spatial resolution of 20 m, by upscaling the 10-m green band to 20 m correspondingly. This scheme, however, wastes the detailed information available at the 10-m resolution. In this paper, to take full advantage of the 10-m information provided by Sentinel-2 images, a novel 10-m spatial resolution MNDWI is produced from Sentinel-2 images by downscaling the 20-m resolution SWIR band to 10 m based on pan-sharpening. Four popular pan-sharpening algorithms, including Principle Component Analysis (PCA, Intensity Hue Saturation (IHS, High Pass Filter (HPF and À Trous Wavelet Transform (ATWT, were applied in this study. The performance of the proposed method was assessed experimentally using a Sentinel-2 image located at the Venice coastland. In the experiment, six water indexes, including 10-m NDWI, 20-m MNDWI and 10-m MNDWI, produced by four pan-sharpening algorithms, were compared. Three levels of results, including the sharpened images, the produced MNDWI images and the finally mapped water bodies, were analysed quantitatively. The results showed that MNDWI can enhance water bodies and suppressbuilt

  12. MODIFIED REVERSE OSMOSIS SYSTEM FOR TREATMENT OF PRODUCED WATERS

    Energy Technology Data Exchange (ETDEWEB)

    Robert L. Lee; Junghan Dong

    2004-06-03

    This final report of ''Modified Reverse Osmosis System for Treatment of Produced Water,'' DOE project No. DE-FC26-00BC15326 describes work performed in the third year of the project. Several good results were obtained, which are documented in this report. The compacted bentonite membranes were replaced by supported bentonite membranes, which exhibited the same salt rejection capability. Unfortunately, it also inherited the clay expansion problem due to water invasion into the interlayer spaces of the compacted bentonite membranes. We noted that the supported bentonite membrane developed in the project was the first of its kind reported in the literature. An {alpha}-alumina-supported MFI-type zeolite membrane synthesized by in-situ crystallization was fabricated and tested. Unlike the bentonite clay membranes, the zeolite membranes maintained stability and high salt rejection rate even for a highly saline solution. Actual produced brines from gas and oil fields were then tested. For gas fields producing brine, the 18,300 ppm TDS (total dissolved solids) in the produced brine was reduced to 3060 ppm, an 83.3% rejection rate of 15,240 ppm salt rejection. For oilfield brine, while the TDS was reduced from 181,600 ppm to 148,900 ppm, an 18% rejection rate of 32,700 ppm reduction, the zeolite membrane was stable. Preliminary results show the dissolved organics, mainly hydrocarbons, did not affect the salt rejection. However, the rejection of organics was inconclusive at this point. Finally, the by-product of this project, the {alpha}-alumina-supported Pt-Co/Na Y catalytic zeolite membrane was developed and demonstrated for overcoming the two-step limitation of nonoxidation methane (CH{sub 4}) conversion to higher hydrocarbons (C{sub 2+}) and hydrogen (H{sub 2}). Detailed experiments to obtain quantitative results of H{sub 2} generation for various conditions are now being conducted. Technology transfer efforts included five manuscripts submitted to

  13. Carbonate and carbon isotopic evolution of groundwater contaminated by produced water brine with hydrocarbons

    International Nuclear Information System (INIS)

    Atekwana, Eliot A.; Seeger, Eric J.

    2015-01-01

    The major ionic and dissolved inorganic carbon (DIC) concentrations and the stable carbon isotope composition of DIC (δ"1"3C_D_I_C) were measured in a freshwater aquifer contaminated by produced water brine with petroleum hydrocarbons. Our aim was to determine the effects of produced water brine contamination on the carbonate evolution of groundwater. The groundwater was characterized by three distinct anion facies: HCO_3"−-rich, SO_4"2"−-rich and Cl"−-rich. The HCO_3"−-rich groundwater is undergoing closed system carbonate evolution from soil CO_2_(_g_) and weathering of aquifer carbonates. The SO_4"2"−-rich groundwater evolves from gypsum induced dedolomitization and pyrite oxidation. The Cl"−-rich groundwater is contaminated by produced water brine and undergoes common ion induced carbonate precipitation. The δ"1"3C_D_I_C of the HCO_3"−-rich groundwater was controlled by nearly equal contribution of carbon from soil CO_2_(_g_) and the aquifer carbonates, such that the δ"1"3C of carbon added to the groundwater was −11.6‰. In the SO_4"2"−-rich groundwater, gypsum induced dedolomitization increased the "1"3C such that the δ"1"3C of carbon added to the groundwater was −9.4‰. In the produced water brine contaminated Cl"−-rich groundwater, common ion induced precipitation of calcite depleted the "1"3C such that the δ"1"3C of carbon added to the groundwater was −12.7‰. The results of this study demonstrate that produced water brine contamination of fresh groundwater in carbonate aquifers alters the carbonate and carbon isotopic evolution. - Highlights: • We studied carbonate and δ"1"3C evolution in groundwater contaminated by produced water brine. • Multiple processes affect the carbonate and δ"1"3C evolution of the groundwater. • The processes are carbonate weathering, dedolomitization and common ion induce calcite precipitation. • The δ"1"3C added to DIC was −11.6‰ for weathering, −9.4‰ for dedolomitization

  14. Characteristics and management of flowback/produced water from hydraulically fractured wells in California - findings from the California SB 4 assessment

    Science.gov (United States)

    Varadharajan, C.; Cooley, H.; Heberger, M. G.; Stringfellow, W. T.; Domen, J. K.; Sandelin, W.; Camarillo, M. K.; Jordan, P. D.; Reagan, M. T.; Donnelly, K.; Birkholzer, J. T.; Long, J. C. S.

    2015-12-01

    As part of a recent assessment of well stimulation in California, we analyzed the hazards and potential impacts of hydraulic fracturing (the primary form of well stimulation in California) on water resources, which included an analysis of the quantity and quality of flowback/produced water generated, current management and disposal practices, associated potential release mechanisms and transport pathways that can lead to contaminants being released into the environment, and practices to mitigate or avoid impacts from produced water on water resources. The wastewater returned after stimulation includes "recovered fluids" (flowback fluids collected into tanks following stimulation, but before the start of production) and "produced water" (water extracted with oil and gas during production). In contrast to hydraulic fracturing in regions with primarily gas production, the quantities of recovered fluids from hydraulically fractured wells in California are small in comparison to the fluids injected (typically analysis indicates some fraction of returning fracturing fluids is likely present in produced water from wells that have been hydraulically fractured. Chemical measurements of recovered fluids show that some samples can contain high levels of some contaminants, including total carbohydrates (indicating the presence of guar, a component of fracturing fluid), total dissolved solids (TDS), trace elements and naturally occurring radioactive material (NORM). Data on produced water chemistry are more limited. In California, produced water is typically managed via pipelines and disposed or reused in many ways. A majority of produced water from hydraulically fractured wells in California is disposed in percolation pits, many of which may lie in areas with good groundwater quality. Some of the remaining produced water is injected into Class II wells; although a few of the wells are under review or have been shut down since they were injecting into aquifers. Other methods of

  15. Stress corrosion cracking resistance of 22% Cr duplex stainless steel in simulated sour environments

    International Nuclear Information System (INIS)

    Kudo, T.; Tsuge, H.; Moroishi, T.

    1989-01-01

    This paper reports the effect of nickel and nitrogen contents on stress corrosion cracking (SCC) of 22%Cr - 3%Mo-base duplex stainless steel investigated in simulated sour environments with respect to both the base metal and the heat-affected zone (HAZ) of welding. The threshold stress and the critical chloride concentration for SCC were evaluated as a function of the ferrite content (α-content) in the alloy. The threshold stress is highest at the α-content of 40 to 45%, and is lowered with decreasing and increasing the α-content from its value. The alloy whose α-content exceeds 80% at the HAZ has also high susceptibilities to pitting corrosion and intergranular corrosion (ICG). The critical chloride concentration for cracking increases with the decrease in the α-content. Moreover, the contents of chromium, nickel and molybdenum in the α-phase are considered to be an important factor for determining the critical chloride concentration

  16. MIB-producing cyanobacteria (Planktothrix sp.) in a drinking water reservoir: distribution and odor producing potential.

    Science.gov (United States)

    Su, Ming; Yu, Jianwei; Zhang, Junzhi; Chen, Hui; An, Wei; Vogt, Rolf D; Andersen, Tom; Jia, Dongmin; Wang, Jingshi; Yang, Min

    2015-01-01

    The production of odorant 2-methylisoborneol (MIB) in water bodies by Planktothrix sp. have not been understood very well. Through a four-year investigation in Miyun Reservoir, a huge mesotrophic drinking water reservoir known to have the MIB episodes, we found that the Planktothrix sp. bloomed during September and October causing the high levels of MIB in the reservoir. The concentration of MIB and the biomass of MIB-producing cyanobacteria Planktothrix were measured (n = 887) at different sites and depths during different seasons. The results indicated that the shallow region of the reservoir is the major habitat for Planktothrix sp. due to that the light is able to penetrate down to the relatively high concentrations of nutrients close to the sediments. Quantile regression analysis between Planktothrix biomass and MIB concentration shows that the risk of MIB exceeding the odor threshold (15 ng L⁻¹) in water was as high as 90% when the Planktothrix density was more than 4.0 × 10⁵ cells L⁻¹, while the risk was reduced to 10% when the Planktothrix density remained below 1.6 × 10⁴ cells L⁻¹. This study will improve the understanding of the environmental behaviors of Planktothrix sp., and can provide useful information for better management of drinking water lakes/reservoirs experiencing the taste and odor (T&O) problems caused by deep living cyanobacterial species.

  17. Evaluation of thiosulfate as a substitute for hydrogen sulfide in sour corrosion fatigue studies

    Science.gov (United States)

    Kappes, Mariano Alberto

    This work evaluates the possibility of replacing hydrogen sulfide (H 2S) with thiosulfate anion (S2O32- ) in sour corrosion fatigue studies. H2S increases the corrosion fatigue crack growth rate (FCGR) and can be present in carbon steel risers and flowlines used in off-shore oil production. Corrosion tests with gaseous H2S require special facilities with safety features, because H2S is a toxic and flammable gas. The possibility of replacing H2S with S2O32-, a non-toxic anion, for studying stress corrosion cracking of stainless and carbon steels in H2S solutions was first proposed by Tsujikawa et al. ( Tsujikawa et al., Corrosion, 1993. 49(5): p. 409-419). In this dissertation, Tsujikawa work will be extended to sour corrosion fatigue of carbon steels. H2S testing is often conducted in deareated condition to avoid oxygen reaction with sulfide that yields sulfur and to mimic oil production conditions. Nitrogen deareation was also adopted in S2O3 2- testing, and gas exiting the cell was forced through a sodium hydroxide trap. Measurements of the sulfide content of this trap were used to estimate the partial pressure of H2S in nitrogen, and Henry's law was used to estimate the content of H2S in the solution in the cell. H2S was produced by a redox reaction of S2O 32-, which required electrons from carbon steel corrosion. This reaction is spontaneous at the open circuit potential of steel. Therefore, H2S concentration was expected to be maximum at the steel surface, and this concentration was estimated by a mass balance analysis. Carbon steel specimens exposed to S2O32- containing solutions developed a film on their surface, composed by iron sulfide and cementite. The film was not passivating and a good conductor of electrons. Hydrogen permeation experiments proved that this film controls the rate of hydrogen absorption of steels exposed to thiosulfate containing solutions. The absorption of hydrogen in S2O3 2- solutions was compared with the absorption of hydrogen in

  18. Produced Water Treatment Using the Switchable Polarity Solvent Forward Osmosis (SPS FO) Desalination Process: Preliminary Engineering Design Basis

    Energy Technology Data Exchange (ETDEWEB)

    Wendt, Daniel; Adhikari, Birendra; Orme, Christopher; Wilson, Aaron

    2016-05-01

    Switchable Polarity Solvent Forward Osmosis (SPS FO) is a semi-permeable membrane-based water treatment technology. INL is currently advancing SPS FO technology such that a prototype unit can be designed and demonstrated for the purification of produced water from oil and gas production operations. The SPS FO prototype unit will used the thermal energy in the produced water as a source of process heat, thereby reducing the external process energy demands. Treatment of the produced water stream will reduce the volume of saline wastewater requiring disposal via injection, an activity that is correlated with undesirable seismic events, as well as generate a purified product water stream with potential beneficial uses. This paper summarizes experimental data that has been collected in support of the SPS FO scale-up effort, and describes how this data will be used in the sizing of SPS FO process equipment. An estimate of produced water treatment costs using the SPS FO process is also provided.

  19. Aqueous extraction of pectin from sour orange peel and its preliminary physicochemical properties.

    Science.gov (United States)

    Hosseini, Seyed Saeid; Khodaiyan, Faramarz; Yarmand, Mohammad Saeid

    2016-01-01

    Sour orange peel, a by-product of the fruit juice industry, was used as a source of pectin. The effects of temperature (75-95°C), time (30-90 min), and liquid-solid ratio (20-40, v/w) were investigated on yield, methoxylation degree (DE), and galacturonic acid content using a Box-Behnken design and response surface methodology. The highest extraction yield (17.95 ± 0.3%) was obtained at temperature of 95°C, time of 90 min, and liquid-solid ratio of 25 (v/w). The DE values for the pectin ranged from 17% to 30.5%, indicating that the pectin was low in methoxyle. The emulsifying activity of pectin extracted under optimal conditions was 45%. The emulsions were 86.6% stable at 4°C and 71.4% at 23°C after 30 days of storage. The pectin exhibited Newtonian flow at low concentrations (≤ 1.0%, w/v); as the concentration increased, pseudoplastic flow became dominant. Copyright © 2015 Elsevier B.V. All rights reserved.

  20. A Molecular Explanation of How the Fog Is Produced When Dry Ice Is Placed in Water

    Science.gov (United States)

    Kuntzleman, Thomas S.; Ford, Nathan; No, Jin-Hwan; Ott, Mark E.

    2015-01-01

    Everyone enjoys seeing the cloudy white fog generated when solid carbon dioxide (dry ice) is placed in water. Have you ever wondered what physical and chemical processes occur to produce this fog? When asked this question, many chemical educators suggest that the fog is produced when atmospheric water vapor condenses on cold carbon dioxide gas…

  1. Solar heating of the produced water of petroleum; Aquecimento solar da agua produzida de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Rogerio Pitanga; Chiavone-Filho, Osvaldo; Bezerra, Magna A. Santos; Melo, Josette Lourdes Sousa de; Oliveira, Jackson Araujo de; Ramos, Rafael E. Moura [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Schuhli, Juliana Bregenski; Andrade, Vivian Tavares de [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

    2008-07-01

    In this work, experimental data of solar heating for common water and saline solution were measured. The solar heater is formed by a flat-plane collector and a thermal reservoir ('boiler'). The objective is to quantify the variation of fluids' temperature, and correlate it to environment variables, especially solar irradiation. Thereby, it is possible to estimate the solar heating of produced water of petroleum. The solar heater is part of a system of treatment of produced water, and its function is to pre-heat the fluid that enters into the solar distiller, increasing the productivity of distilled water. A saline solution that represents produced water was used in the experiments, using sodium chloride (1000 ppm). The experimental data demonstrates that the solar heater is capable to heat the fluid to temperatures close to 70 deg C, reaching temperatures close to 50 deg C even during cloudy days with low solar radiation. Furthermore, the solar collector energy system provides a higher rate of heating and trough of the thermal reservoir the temperature can remain longer. These are important aspects to the integration with solar distillation. (author)

  2. Solar heating of the produced water of petroleum; Aquecimento solar da agua produzida de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Rogerio Pitanga; Chiavone-Filho, Osvaldo; Bezerra, Magna A. Santos; Melo, Josette Lourdes Sousa de; Oliveira, Jackson Araujo de; Ramos, Rafael E. Moura [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Schuhli, Juliana Bregenski; Andrade, Vivian Tavares de [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

    2008-07-01

    In this work, experimental data of solar heating for common water and saline solution were measured. The solar heater is formed by a flat-plane collector and a thermal reservoir ('boiler'). The objective is to quantify the variation of fluids' temperature, and correlate it to environment variables, especially solar irradiation. Thereby, it is possible to estimate the solar heating of produced water of petroleum. The solar heater is part of a system of treatment of produced water, and its function is to pre-heat the fluid that enters into the solar distiller, increasing the productivity of distilled water. A saline solution that represents produced water was used in the experiments, using sodium chloride (1000 ppm). The experimental data demonstrates that the solar heater is capable to heat the fluid to temperatures close to 70 deg C, reaching temperatures close to 50 deg C even during cloudy days with low solar radiation. Furthermore, the solar collector energy system provides a higher rate of heating and trough of the thermal reservoir the temperature can remain longer. These are important aspects to the integration with solar distillation. (author)

  3. Characterizing the variability in chemical composition of flowback and produced waters - results from lab and field studies

    Science.gov (United States)

    Vieth-Hillebrand, Andrea; Wilke, Franziska D. H.; Schmid, Franziska E.; Zhu, Yaling; Lipińska, Olga; Konieczyńska, Monika

    2017-04-01

    The huge volumes and unknown composition of flowback and produced waters cause major public concerns about the environmental and social compatibility of hydraulic fracturing and the exploitation of gas from unconventional reservoirs. Flowback and produced waters contain not only residues of fracking additives but also chemical species that are dissolved from the target shales themselves. Shales are a heterogeneous mixture of minerals, organic matter, and formation water and little is actually understood about the fluid-rock interactions occurring during hydraulic fracturing of the shales and their effects on the chemical composition of flowback and produced water. To overcome this knowledge gap, interactions of different shales with different artificial stimulation fluids were studied in lab experiments under ambient and elevated temperature and pressure conditions. These lab experiments showed clearly that fluid-rock interactions change the chemical composition of the initial stimulation fluid and that geochemistry of the fractured shale is relevant for understanding flowback water composition. In addition, flowback water samples were taken after hydraulic fracturing of one horizontal well in Pomeranian region, Poland and investigated for their chemical composition. With this presentation, results from lab and field studies will be presented and compared to decipher possible controls on chemical compositions of flowback and produced water.

  4. Integrated fate modeling for exposure assessment of produced water on the Sable Island Bank (Scotian shelf, Canada).

    Science.gov (United States)

    Berry, Jody A; Wells, Peter G

    2004-10-01

    Produced water is the largest waste discharge from the production phase of oil and gas wells. Produced water is a mixture of reservoir formation water and production chemicals from the separation process. This creates a chemical mixture that has several components of toxic concern, ranging from heavy metals to soluble hydrocarbons. Analysis of potential environmental effects from produced water in the Sable Island Bank region (NS, Canada) was conducted using an integrated modeling approach according to the ecological risk assessment framework. A hydrodynamic dispersion model was used to describe the wastewater plume. A second fugacity-based model was used to describe the likely plume partitioning in the local environmental media of water, suspended sediment, biota, and sediment. Results from the integrated modeling showed that the soluble benzene and naphthalene components reach chronic no-effect concentration levels at a distance of 1.0 m from the discharge point. The partition modeling indicated that low persistence was expected because of advection forces caused by tidal currents for the Sable Island Bank system. The exposure assessment for the two soluble hydrocarbon components suggests that the risks of adverse environmental effects from produced water on Sable Island Bank are low.

  5. An overview on exploration and environmental impact of unconventional gas sources and treatment options for produced water.

    Science.gov (United States)

    Silva, Tânia L S; Morales-Torres, Sergio; Castro-Silva, Sérgio; Figueiredo, José L; Silva, Adrián M T

    2017-09-15

    Rising global energy demands associated to unbalanced allocation of water resources highlight the importance of water management solutions for the gas industry. Advanced drilling, completion and stimulation techniques for gas extraction, allow more economical access to unconventional gas reserves. This stimulated a shale gas revolution, besides tight gas and coalbed methane, also causing escalating water handling challenges in order to avoid a major impact on the environment. Hydraulic fracturing allied to horizontal drilling is gaining higher relevance in the exploration of unconventional gas reserves, but a large amount of wastewater (known as "produced water") is generated. Its variable chemical composition and flow rates, together with more severe regulations and public concern, have promoted the development of solutions for the treatment and reuse of such produced water. This work intends to provide an overview on the exploration and subsequent environmental implications of unconventional gas sources, as well as the technologies for treatment of produced water, describing the main results and drawbacks, together with some cost estimates. In particular, the growing volumes of produced water from shale gas plays are creating an interesting market opportunity for water technology and service providers. Membrane-based technologies (membrane distillation, forward osmosis, membrane bioreactors and pervaporation) and advanced oxidation processes (ozonation, Fenton, photocatalysis) are claimed to be adequate treatment solutions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Tritium contamination in [18O] water containing 18F produced by a cyclotron

    International Nuclear Information System (INIS)

    Ito, S.; Saze, T.; Sakane, H.; Nishizawa, K.

    2003-01-01

    Tritium in the target [ 18 O] water irradiated with 9.6 MeV protons for producing [ 18 F] fluoride by 18 O(p, n) 18 F reaction was predicted from the consideration on the Q value of the 18 O(p, t) 16 O reaction. A tritium beta ray spectrum was measured by a liquid scintillation counter equipped with a multichannel analyzer. The ratio of the 3 H activity to the 18 F activity in the [ 18 O] target water was 2.4x10 -6 at the beam current of 25μA. Tritium also was detected in the [ 18 O] water for recycling and the wasted acetonitrile [ 18 O] water. The purified [ 18 F]-FDG solution was not contaminated by 3 H. The 40% 3 H out of the produced activity was lost in the course of the [ 18 F]-FDG synthesis. It was suggested that 3 H evaporated into the air during [ 18 F]-FDG synthesis and caused contamination of the workroom. The radiation workers should be prevented from environmental 3 H contamination. (author)

  7. Environmental effects of produced water from offshore petroleum industry

    International Nuclear Information System (INIS)

    Riksheim, H.; Johnsen, S.

    1993-01-01

    Mathematical models describing the fate and distribution of the discharged produced water are available for both the Statfjord and Gullfaks field. However, the value of these models are very limited if its predicted results cannot be verified by measurements of the actual results. An approach to this problem was made by sampling of water from locations in the vicinity of the discharge points at one of the oil producing platforms at the Statfjord and Gullfaks fields. Samples were collected at levels 5m below surface at locations 10m, 100m and 500m downstream of the discharge points, and at a reference site located midway between the fields. The concentrations of total hydrocarbon content, aromatic hydrocarbons, phenols and a number of heavy metals were determined in all samples. Increased levels of several of the analyzed parameters were detected at the innermost locations at both fields, compared to the distant locations and the natural background levels. At the Statfjord field increased levels of phenols and PAH were also observed at the locations 100 m and 500 m away from the discharge point. The results showed that dilution factors of 1:1000 and higher were found for the innermost locations, while the dilution models predicted a primary dilution of 1:30--1:50 within a distance of 100 m away from the platforms

  8. Appearance and water quality of turbidity plumes produced by dredging in Tampa Bay, Florida

    Science.gov (United States)

    Goodwin, Carl R.; Michaelis, D.M.

    1984-01-01

    Turbidity plumes in Tampa Bay, Florida, produced during ship-channel dredging operations from February 1977 to August 1978, were monitored in order to document plume appearance and water quality, evaluate plume influence on the characteristics of Tampa Bay water, and provide a data base for comparison with other areas that have similar sediment, dredge, placement, containment, and tide conditions. The plumes investigated originated from the operation of one hopper dredge and three cutterhead-pipeline dredges. Composition of bottom sediment was found to vary from 85 percent sand and shell fragments to 60 percent silt and clay. Placement methods for dredged sediment included beach nourishment, stationary submerged discharge, oscillating surface discharge, and construction of emergent dikes. Tidal currents ranged from slack water to flow velocities of 0.60 meter per second. Plumes were monitored simultaneously by (1) oblique and vertical 35-millimeter aerial photography and (2) water-quality sampling to determine water clarity and concentrations of nutrients, metals, pesticides, and industrial compounds. Forty-nine photographs depict plumes ranging in length from a few tens of meters to several kilometers and ranging in turbidity level from hopper-dredge unloading operations also produced plumes of low visibility. Primary turbidity plumes were produced directly by dredging and placement operations; secondary plumes were produced indirectly by resuspension of previously deposited material. Secondary plumes were formed both by erosion, in areas of high-velocity tidal currents, and by turbulence from vessels passing over fine material deposited in shallow areas. Where turbidity barriers were not used, turbidity plumes visible at the surface were good indicators of the location of turbid water at depth. Where turbidity barriers were used, turbid bottom water was found at locations having no visible surface plumes. A region of rapidly accelerating then decelerating flow

  9. Microbial oxidation of soluble sulfide in produced water from the Bakkeen Sands

    Energy Technology Data Exchange (ETDEWEB)

    Gevertz, D.; Zimmerman, S. [Agouron Institute, La Jolla, CA (United States); Jenneman, G.E. [Phillips Petroleum Company, Bartlesville, OK (United States)] [and others

    1995-12-31

    The presence of soluble sulfide in produced water results in problems for the petroleum industry due to its toxicity, odor, corrosive nature, and potential for wellbore plugging. Sulfide oxidation by indigenous nitrate-reducing bacteria (NRB) present in brine collected from wells at the Coleville Unit (CVU) in Saskatchewan, Canada, was investigated. Sulfide oxidation took place readily when nitrate and phosphate were added to brine enrichment cultures, resulting in a decrease in sulfide levels of 99-165 ppm to nondetectable levels (< 3.3 ppm). Produced water collected from a number of producing wells was screened to determine the time required for complete sulfide oxidation, in order to select candidate wells for treatment. Three wells were chosen, based on sulfide removal in 48 hours or less. These wells were treated down the backside of the annulus with a solution containing 10 mM KNO{sub 3} and 100 {mu}M NaH{sub 2}PO{sub 4}. Following a 24- to 72-hour shut-in, reductions in pretreatment sulfide levels of greater than 90% were observed for two of the wells, as well as sustained sulfide reductions of 50% for at least two days following startup. NRB populations in the produced brine were observed to increase significantly following treatment, but no significant increases in sulfate-reducing bacteria were observed. These results demonstrate the technical feasibility of stimulating indigenous populations of NRB to remediate and control sulfide in produced brine.

  10. Identification, Verification, and Compilation of Produced Water Management Practices for Conventional Oil and Gas Production Operations

    Energy Technology Data Exchange (ETDEWEB)

    Rachel Henderson

    2007-09-30

    The project is titled 'Identification, Verification, and Compilation of Produced Water Management Practices for Conventional Oil and Gas Production Operations'. The Interstate Oil and Gas Compact Commission (IOGCC), headquartered in Oklahoma City, Oklahoma, is the principal investigator and the IOGCC has partnered with ALL Consulting, Inc., headquartered in Tulsa, Oklahoma, in this project. State agencies that also have partnered in the project are the Wyoming Oil and Gas Conservation Commission, the Montana Board of Oil and Gas Conservation, the Kansas Oil and Gas Conservation Division, the Oklahoma Oil and Gas Conservation Division and the Alaska Oil and Gas Conservation Commission. The objective is to characterize produced water quality and management practices for the handling, treating, and disposing of produced water from conventional oil and gas operations throughout the industry nationwide. Water produced from these operations varies greatly in quality and quantity and is often the single largest barrier to the economic viability of wells. The lack of data, coupled with renewed emphasis on domestic oil and gas development, has prompted many experts to speculate that the number of wells drilled over the next 20 years will approach 3 million, or near the number of current wells. This level of exploration and development undoubtedly will draw the attention of environmental communities, focusing their concerns on produced water management based on perceived potential impacts to fresh water resources. Therefore, it is imperative that produced water management practices be performed in a manner that best minimizes environmental impacts. This is being accomplished by compiling current best management practices for produced water from conventional oil and gas operations and to develop an analysis tool based on a geographic information system (GIS) to assist in the understanding of watershed-issued permits. That would allow management costs to be kept in

  11. Non-microcystin producing Microcystis wesenbergii (Komarek) Komarek (Cyanobacteria) representing a main waterbloom-forming species in Chinese waters

    International Nuclear Information System (INIS)

    Xu Yao; Wu Zhongxing; Yu Boshi; Peng Xin; Yu Gongliang; Wei Zhihong; Wang Guoxiang; Li Renhui

    2008-01-01

    It is well known that several morphospecies of Microcystis, such as Microcystis aeruginosa (Kuetzing) Lemmermann and Microcystis viridis (A. Brown) Lemmermann can produce hepatotoxic microcystins. However, previous studies gave contradictory conclusions about microcystin production of Microcystis wesenbergii (Komarek) Komarek. In the present study, ten Microcystis morphospecies were identified in waterblooms of seven Chinese waterbodies, and Microcystis wesenbergii was shown as the dominant species in these waters. More than 250 single colonies of M. wesenbergii were chosen, under morphological identification, to examine whether M. wesenbergii produce hepatotoxic microcystin by using multiplex PCR for molecular detection of a region (mcyA) of microcystin synthesis genes, and chemical analyses of microcystin content by ELISA and HPLC for 21 isolated strains of M. wesenbergii from these waters were also performed. Both molecular and chemical methods demonstrated that M. wesenbergii from Chinese waters did not produce microcystin. - Both molecular and chemical methods demonstrated that Microcystis wesenbergii was not a microcystin producer in Chinese waters

  12. Auxiliary units for refining of high nitrogen content oils: Premium II refinery case

    Energy Technology Data Exchange (ETDEWEB)

    Nicolato, Paolo Contim; Pinotti, Rafael [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

    2012-07-01

    PETROBRAS is constantly investing on its refining park in order to increase the production of clean and stable fuels and to be capable to process heavier oils with high contaminants content. Sulfur and nitrogen are the main heteroatoms present in petroleum. They are responsible for some undesirable fuels properties like corrosivity and instability, and also emit pollutants when burnt. Hydrotreating and hydrocracking processes are designed to remove these contaminants and adjust other fuel properties, generating, as byproduct, sour gases and sour water streams rich in H{sub 2}S and NH{sub 3}, which are usually sent to Sour Water Treatment Units and Sulfur Recovery Units. The regeneration of the amine used for the light streams treatment, as fuel gas and LPG, also generates sour gas streams that must be also sent to Sulfur Recovery Units. As the ammonia content in the sour streams increases, some design parameters must be adjusted to avoid increasing the Refinery emissions. Sulfur Recovery Units must provide proper NH3 destruction. Sour Water Treatment must have a proper segregation between H{sub 2}S and ammonia streams, whenever desirable. Amine Regeneration Systems must have an efficient procedure to avoid the ammonia concentration in the amine solution. This paper presents some solutions usually applied to the Petroleum Industry and analyses some aspects related to Premium II Refinery Project and how its design will help the Brazilian refining park to meet future environmental regulation and market demands. (author)

  13. Risk assessment for produced water discharges to Louisiana open bays. Final report

    International Nuclear Information System (INIS)

    Meinhold, A.F.; DePhillips, M.P.; Holtzman, S.

    1996-01-01

    The US Department of Energy (USDOE) has a program of research in the environmental aspects of oil and gas extraction. This sampling project will characterize the environmental impacts associated with the discharge of naturally occurring radioactive materials (NORM), metals and organics in produced water. This report is part of a series of studies of the health and ecological risks from discharges of produced water to the Gulf of Mexico, supported by the USDOE. These assessments are being coordinated with the field study, using the collected data to perform human health and ecological risk assessments. These assessments will provide input to regulators in the development of guidelines and permits, and to industry in the development and use of appropriate discharge practices. The initial human health and ecological risk assessments consist of conservative screening analyses meant to identify potentially important contaminants, and to eliminate others from further consideration. More quantitative assessments were done for contaminants identified, in the screening analysis, as being of potential concern. Section 2 gives an overview of human health and ecological risk assessment to help put the analyses presented here in perspective. Section 3 provides the hazard assessment portion of the risk assessment, and identifies the important receptors and pathways of concern. Section 3 also outlines the approach taken to the risk assessments presented in the rest of the report. The remaining sections (4 through 9) present the human health and ecological risk assessments for discharges of produced water to open bays in Louisiana

  14. Fate and groundwater impacts of produced water releases at OSPER "B" site, Osage County, Oklahoma

    Science.gov (United States)

    Kharaka, Y.K.; Kakouros, E.; Thordsen, J.J.; Ambats, G.; Abbott, M.M.

    2007-01-01

    For the last 5 a, the authors have been investigating the transport, fate, natural attenuation and ecosystem impacts of inorganic and organic compounds in releases of produced water and associated hydrocarbons at the Osage-Skiatook Petroleum Environmental Research (OSPER) "A" and "B" sites, located in NE Oklahoma. Approximately 1.0 ha of land at OSPER "B", located within the active Branstetter lease, is visibly affected by salt scarring, tree kills, soil salinization, and brine and petroleum contamination. Site "B" includes an active production tank battery and adjacent large brine pit, two injection well sites, one with an adjacent small pit, and an abandoned brine pit and tank battery site. Oil production in this lease started in 1938, and currently there are 10 wells that produce 0.2-0.5 m3/d (1-3 bbl/d) oil, and 8-16 m3/d (50-100 bbl/d) brine. Geochemical data from nearby oil wells show that the produced water source is a Na-Ca-Cl brine (???150,000 mg/L TDS), with high Mg, but low SO4 and dissolved organic concentrations. Groundwater impacts are being investigated by detailed chemical analyses of water from repeated sampling of 41 boreholes, 1-71 m deep. The most important results at OSPER "B" are: (1) significant amounts of produced water from the two active brine pits percolate into the surficial rocks and flow towards the adjacent Skiatook reservoir, but only minor amounts of liquid petroleum leave the brine pits; (2) produced-water brine and minor dissolved organics have penetrated the thick (3-7 m) shale and siltstone units resulting in the formation of three interconnected plumes of high-salinity water (5000-30,000 mg/L TDS) that extend towards the Skiatook reservoir from the two active and one abandoned brine pits; and (3) groundwater from the deep section of only one well, BR-01 located 330 m upslope and west of the site, appear not to be impacted by petroleum operations. ?? 2007.

  15. Impacts from oil and gas produced water discharges on the Gulf of Mexico hypoxic zone

    International Nuclear Information System (INIS)

    Parker, M.E.; Satterlee, K.; Veil, J.A.

    2006-01-01

    Shallow water areas of the Gulf of Mexico continental shelf experience low dissolved oxygen (hypoxia) each summer. The hypoxic zone is primarily caused by input of nutrients from the Mississippi and Atchafalaya Rivers. The nutrients stimulate the growth of phytoplankton, which leads to reduction of the oxygen concentration near the sea floor. During the renewal of an offshore discharge permit used by the oil and gas industry in the Gulf of Mexico, the U.S. Environmental Protection Agency (EPA) identified the need to assess the potential contribution from produced water discharges to the occurrence of hypoxia. The EPA permit required either that all platforms in the hypoxic zone submit produced water samples, or that industry perform a coordinated sampling program. This paper, based on a report submitted to EPA in August 2005 (1), describes the results of the joint industry sampling program and the use of those results to quantify the relative significance of produced water discharges in the context of other sources on the occurrence of hypoxia in the Gulf of Mexico. In the sampling program, 16 facilities were selected for multiple sampling - three times each at one month intervals-- and another 34 sites for onetime sampling. The goal of the sampling program was to quantify the sources and amount of oxygen demand associated with a variety of Gulf of Mexico produced waters. Data collected included direct oxygen demand measured by BOD5 (5-day biochemical oxygen demand) and TOC (total organic carbon) and indirect oxygen demand measured by nitrogen compounds (ammonia, nitrate, nitrate, and TKN (total Kjeldahl nitrogen)) and phosphorus (total phosphorus and orthophosphate). These data will serve as inputs to several available computer models currently in use for forecasting the occurrence of hypoxia in the Gulf of Mexico. The output of each model will be compared for consistency in their predictions and then a semi-quantitative estimate of the relative significance of

  16. Origin of salinity in produced waters from the Palm Valley gas field, Northern Territory, Australia

    International Nuclear Information System (INIS)

    Andrew, Anita S.; Whitford, David J.; Berry, Martin D.; Barclay, Stuart A.; Giblin, Angela M.

    2005-01-01

    The chemical composition and evolution of produced waters associated with gas production in the Palm Valley gas field, Northern Territory, has important implications for issues such as gas reserve calculations, reservoir management and saline water disposal. The occurrence of saline formation water in the Palm Valley field has been the subject of considerable debate. There were no occurrences of mobile water early in the development of the field and only after gas production had reduced the reservoir pressure, was saline formation water produced. Initially this was in small quantities but has increased dramatically with time, particularly after the initiation of compression in November 1996. The produced waters range from highly saline (up to 300,000 mg/L TDS), with unusual enrichments in Ca, Ba and Sr, to low salinity fluids that may represent condensate waters. The Sr isotopic compositions of the waters ( 87 Sr/ 86 Sr = 0.7041-0.7172) are also variable but do not correlate closely with major and trace element abundances. Although the extreme salinity suggests possible involvement of evaporite deposits lower in the stratigraphic sequence, the Sr isotopic composition of the high salinity waters suggests a more complex evolutionary history. The formation waters are chemically and isotopically heterogeneous and are not well mixed. The high salinity brines have Sr isotopic compositions and other geochemical characteristics more consistent with long-term residence within the reservoir rocks than with present-day derivation from a more distal pool of brines associated with evaporites. If the high salinity brines entered the reservoir during the Devonian uplift and were displaced by the reservoir gas into a stagnant pool, which has remained near the reservoir for the last 300-400 Ma, then the size of the brine pool is limited. At a minimum, it might be equivalent to the volume displaced by the reservoired gas

  17. Applications of UT results to confirm defects findings by utilization of relevant metallurgical investigations techniques on gas/condensate pipeline working in wet sour gas environment

    Science.gov (United States)

    El-Azhari, O. A.; Gajam, S. Y.

    2015-03-01

    The gas/condensate pipe line under investigation is a 12 inch diameter, 48 km ASTM, A106 steel pipeline, carrying hydrocarbons containing wet CO2 and H2S.The pipe line had exploded in a region 100m distance from its terminal; after 24 years of service. Hydrogen induced cracking (HIC) and sour gas corrosion were expected due to the presence of wet H2S in the gas analysis. In other areas of pipe line ultrasonic testing was performed to determine whether the pipeline can be re-operated. The results have shown presence of internal planner defects, this was attributed to the existence of either laminations, type II inclusions or some service defects such as HIC and step wise cracking (SWC).Metallurgical investigations were conducted on fractured samples as per NACE standard (TM-0284-84). The obtained results had shown macroscopic cracks in the form of SWC, microstructure of steel had MnS inclusions. Crack sensitivity analyses were calculated and the microhardness testing was conducted. These results had confirmed that the line material was suffering from sour gas deteriorations. This paper correlates the field UT inspection findings with those methods investigated in the laboratory. Based on the results obtained a new HIC resistance material pipeline needs to be selected.

  18. Growth Inhibition of Sulfate-Reducing Bacteria in Produced Water from the Petroleum Industry Using Essential Oils.

    Science.gov (United States)

    Souza, Pamella Macedo de; Goulart, Fátima Regina de Vasconcelos; Marques, Joana Montezano; Bizzo, Humberto Ribeiro; Blank, Arie Fitzgerald; Groposo, Claudia; Sousa, Maíra Paula de; Vólaro, Vanessa; Alviano, Celuta Sales; Moreno, Daniela Sales Alviano; Seldin, Lucy

    2017-04-19

    Strategies for the control of sulfate-reducing bacteria (SRB) in the oil industry involve the use of high concentrations of biocides, but these may induce bacterial resistance and/or be harmful to public health and the environment. Essential oils (EO) produced by plants inhibit the growth of different microorganisms and are a possible alternative for controlling SRB. We aimed to characterize the bacterial community of produced water obtained from a Brazilian petroleum facility using molecular methods, as well as to evaluate the antimicrobial activity of EO from different plants and their major components against Desulfovibrio alaskensis NCIMB 13491 and against SRB growth directly in the produced water. Denaturing gradient gel electrophoresis revealed the presence of the genera Pelobacter and Marinobacterium , Geotoga petraea , and the SRB Desulfoplanes formicivorans in our produced water samples. Sequencing of dsrA insert-containing clones confirmed the presence of sequences related to D. formicivorans . EO obtained from Citrus aurantifolia , Lippia alba LA44 and Cymbopogon citratus , as well as citral, linalool, eugenol and geraniol, greatly inhibited (minimum inhibitory concentration (MIC) = 78 µg/mL) the growth of D. alaskensis in a liquid medium. The same MIC was obtained directly in the produced water with EO from L. alba LA44 (containing 82% citral) and with pure citral. These findings may help to control detrimental bacteria in the oil industry.

  19. Growth Inhibition of Sulfate-Reducing Bacteria in Produced Water from the Petroleum Industry Using Essential Oils

    Directory of Open Access Journals (Sweden)

    Pamella Macedo de Souza

    2017-04-01

    Full Text Available Strategies for the control of sulfate-reducing bacteria (SRB in the oil industry involve the use of high concentrations of biocides, but these may induce bacterial resistance and/or be harmful to public health and the environment. Essential oils (EO produced by plants inhibit the growth of different microorganisms and are a possible alternative for controlling SRB. We aimed to characterize the bacterial community of produced water obtained from a Brazilian petroleum facility using molecular methods, as well as to evaluate the antimicrobial activity of EO from different plants and their major components against Desulfovibrio alaskensis NCIMB 13491 and against SRB growth directly in the produced water. Denaturing gradient gel electrophoresis revealed the presence of the genera Pelobacter and Marinobacterium, Geotoga petraea, and the SRB Desulfoplanes formicivorans in our produced water samples. Sequencing of dsrA insert-containing clones confirmed the presence of sequences related to D. formicivorans. EO obtained from Citrus aurantifolia, Lippia alba LA44 and Cymbopogon citratus, as well as citral, linalool, eugenol and geraniol, greatly inhibited (minimum inhibitory concentration (MIC = 78 µg/mL the growth of D. alaskensis in a liquid medium. The same MIC was obtained directly in the produced water with EO from L. alba LA44 (containing 82% citral and with pure citral. These findings may help to control detrimental bacteria in the oil industry.

  20. Cleaning the Produced Water in Offshore Oil Production by Using Plant-wide Optimal Control Strategy

    DEFF Research Database (Denmark)

    Yang, Zhenyu; Pedersen, Simon; Løhndorf, Petar Durdevic

    2014-01-01

    To clean the produced water is always a challenging critical issue in the offshore oil & gas industry. By employing the plant-wide control technology, this paper discussed the opportunity to optimize the most popular hydrocyclone-based Produced Water Treatment (PWT) system. The optimizations of t...... of this research is to promote a technical breakthrough in the PWT control design, which can lead to the best environmental protection in the oil & gas production, without sacrificing the production capability and production costs....

  1. Novel Downhole Electromagnetic Flowmeter for Oil-Water Two-Phase Flow in High-Water-Cut Oil-Producing Wells.

    Science.gov (United States)

    Wang, Yanjun; Li, Haoyu; Liu, Xingbin; Zhang, Yuhui; Xie, Ronghua; Huang, Chunhui; Hu, Jinhai; Deng, Gang

    2016-10-14

    First, the measuring principle, the weight function, and the magnetic field of the novel downhole inserted electromagnetic flowmeter (EMF) are described. Second, the basic design of the EMF is described. Third, the dynamic experiments of two EMFs in oil-water two-phase flow are carried out. The experimental errors are analyzed in detail. The experimental results show that the maximum absolute value of the full-scale errors is better than 5%, the total flowrate is 5-60 m³/d, and the water-cut is higher than 60%. The maximum absolute value of the full-scale errors is better than 7%, the total flowrate is 2-60 m³/d, and the water-cut is higher than 70%. Finally, onsite experiments in high-water-cut oil-producing wells are conducted, and the possible reasons for the errors in the onsite experiments are analyzed. It is found that the EMF can provide an effective technology for measuring downhole oil-water two-phase flow.

  2. Novel Downhole Electromagnetic Flowmeter for Oil-Water Two-Phase Flow in High-Water-Cut Oil-Producing Wells

    Directory of Open Access Journals (Sweden)

    Yanjun Wang

    2016-10-01

    Full Text Available First, the measuring principle, the weight function, and the magnetic field of the novel downhole inserted electromagnetic flowmeter (EMF are described. Second, the basic design of the EMF is described. Third, the dynamic experiments of two EMFs in oil-water two-phase flow are carried out. The experimental errors are analyzed in detail. The experimental results show that the maximum absolute value of the full-scale errors is better than 5%, the total flowrate is 5–60 m3/d, and the water-cut is higher than 60%. The maximum absolute value of the full-scale errors is better than 7%, the total flowrate is 2–60 m3/d, and the water-cut is higher than 70%. Finally, onsite experiments in high-water-cut oil-producing wells are conducted, and the possible reasons for the errors in the onsite experiments are analyzed. It is found that the EMF can provide an effective technology for measuring downhole oil-water two-phase flow.

  3. Families near proposed sour gas wells wary company can protect them

    International Nuclear Information System (INIS)

    Anon

    2005-01-01

    Public objections to the Compton Petroleum Corporation's intentions to add six new sour gas wells to an existing well it now operates near a residential area in the Calgary area, are discussed. Fifty-five families live within 15 km of the proposed wellsite; they are concerned about the safety of the plan, claiming that the company has not done enough to inform them about the potential hazards. Company officials assured residents that those living within the emergency zone (i.e. within four km of the wells) will be evacuated from the area before a blowout occurs. As far as residents outside the emergency zone are concerned, independent risk analysis experts testified that the risk to those residents is negligible. The company claims that Alberta law compels them to maximize the recovery of petroleum resources and by not drilling the proposed wells the company leaves itself open to charges for leaving some reserves in the ground. The Company also claims that by drilling the additional wells, it would be in a position to deplete the gas reserves faster, shut down the existing wells and return the land to the city much sooner than otherwise would be possible. Lawyers for the Coalition of Concerned Communities are challenging the Company's claim that the wells must be drilled so industry can make way for city expansion. 1 fig

  4. 3-Dimensional Microorifice Fabricated Utilizing Single Undercut Etching Process for Producing Ultrasmall Water and Chitosan Droplets

    Directory of Open Access Journals (Sweden)

    Che-Hsin Lin

    2013-01-01

    Full Text Available This research reports a microfluidic device for producing small droplets via a microorifice and a T-junction structure. The orifice is fabricated using an isotropic undercut etching process of amorphous glass materials. Since the equivalent hydraulic diameter of the produced microorifice can be as small as 1.1 μm, the microdevice can easily produce droplets of the size smaller than 10 μm in diameter. In addition, a permanent hydrophobic coating technique is also applied to modify the main channel to be hydrophobic to enhance the formation of water-based droplets. Experimental results show that the developed microfluidic chip with the ultrasmall orifice can steadily produce water-in-oil droplets with different sizes. Uniform water-in-oil droplets with the size from 60 μm to 6.5 μm in diameter can be formed by adjusting the flow rate ratio of the continuous phase and the disperse phases from 1 to 7. Moreover, curable linear polymer of chitosan droplets with the size smaller than 100 μm can also be successfully produced using the developed microchip device. The microfluidic T-junction with a micro-orifice developed in the present study provides a simple yet efficient way to produce various droplets of different sizes.

  5. Carbon economy of sour orange in response to different Glomus spp.

    Science.gov (United States)

    Graham, J. H.; Drouillard, D. L.; Hodge, N. C.

    1996-01-01

    Vesicular-arbuscular mycorrhizal (M) fungal colonization, growth, and nonstructural carbohydrate status of sour orange (Citrus aurantium L.) seedlings were compared at low- and high-phosphorus (P) supply following inoculation with four Glomus isolates: G. intraradices (Gi, FL208), G. etunicatum (Ge, UT316), G. claroideum (Gc, SC186), and Glomus sp. (G329, FL906). Nonmycorrhizal (NM) seedlings served as controls. At low-P supply, increases in incidence of M colonization, vesicles and accumulation of fungal fatty acid 16:1omega(5)C in roots were most rapid for G329-inoculated seedlings, followed closely by Gi- and Gc-inoculated seedlings. Glomus etunicatum was a less aggressive colonizer and produced lower rates of fungal fatty acid accumulation in seedling roots than the other Glomus species. Nonmycorrhizal and Ge-inoculated seedlings had lower P status and growth rates than seedlings inoculated with Gi or G329. Glomus claroideum increased seedling P status, but growth rate was lower than for seedlings colonized by Gi or G329, suggesting higher belowground costs for Gc colonization. In P-sufficient roots colonized by Gi, Gc, or G329, starch and ketone sugar concentrations were lower than in P-deficient NM and Ge-inoculated plants. Under conditions of high-P supply where mycorrhizae provided no P benefit to the seedlings, colonization by Gc, Gi, and G329 was delayed and reduced compared to that at low-P supply; however, the relative colonization rates among Glomus spp. were similar. Colonization by Ge was not detected in roots until 64 days after inoculation. Compared to NM seedlings, growth rates of mycorrhizal seedlings were reduced by the three aggressive fungi but not by the less aggressive Ge. After 64 days, starch and ketone sugar concentrations were lower in fibrous roots colonized by Gc, Gi, and G329 than in NM roots, indicating greater utilization of nonstructural carbohydrates in roots colonized by the aggressive fungi. After 49 days, colonization by the

  6. Biological soil attributes in oilseed crops irrigated with oilfield produced water in the semi-arid region

    Directory of Open Access Journals (Sweden)

    Ana Clarice Melo Azevedo de Meneses

    Full Text Available ABSTRACT Wastewater from oil is the main residue of the oil industry. Studies have shown that wastewater, or produced water, can be treated and used as an alternative source for the irrigation of oilseed crops. The aim of this work was to evaluate the effect of treated produced water on the biological properties of soil cultivated with the castor bean cv. BRS Energy and the sunflower cv. BRS 321 respectively, for two and three successive cycles of grain production. The first cycle in the sunflower and castor bean corresponds to the dry season and the second cycle to the rainy season. The third crop cycle in the sunflower relates to the dry season. The research was carried out from August 2012 to October 2013, in the town of Aracati, in the State of Ceará (Brazil, where both crops were submitted to irrigation with filtered produced water (FPW, produced water treated by reverse osmosis (OPW, or groundwater water from the Açu aquifer (ACW, and to no irrigation (RFD. The treatments, with three replications, were evaluated during the periods of pre-cultivation and plant reproduction for soil respiration (Rs, total organic carbon (TOC and the population density of bacteria (Bact and filamentous fungi (Fung in the soil. In the sunflower crop, these soil attributes are sensitive to the irrigation water used. Irrigation of the castor bean affects soil respiration. Under the conditions of this study, irrigation with FPW may be a short-term alternative in the castor bean and sunflower crops.

  7. Biotreatment of produced waters for volume reduction and contaminant removal

    Energy Technology Data Exchange (ETDEWEB)

    Negri, M.C.; Hinchman, R.R. [Argonne National Lab., IL (United States); Mollock, J. [Devon Energy Corp., Oklahoma City, OK (United States)

    1997-10-01

    Produced water is wastewater that is brought to the surface from natural gas wells during natural gas production. Its constituents, mostly salt, with traces of hydrocarbons and heavy metals, are a significant disposal problem. Argonne National Laboratory (ANL), in partnership with the Gas Research Institute (GRI), has developed a low-cost, low-tech method, in which green plants are used to reduce the volume of produced water. The authors have designed an engineered bioreactor system, which is modeled after natural saline wetland ecosystems. The plant bioreactor system maximizes plant evapotranspiration to reduce wastewater volume and, concurrently, may function as a biological filter to enhance contaminant degradation and immobilization in the root/rhizosphere zone. Halophyte plant species having high salt tolerance and high transpiration rates were selected after they tested them in greenhouse experiments. Models obtained by using their greenhouse findings reduced the volume of the wastewater (up to 6% salt) by 75% in about 8 days. A field demonstration of the bioreactor, designed on the basis of the results from the greenhouse study, is successfully under way at a natural gas well site in Oklahoma. The process could offer the petroleum industry a low-cost biological alternative to existing expensive options.

  8. Fertilisation and hatching success of Atlantic cod (Gadus morhua) eggs when exposed to various concentrations of produced water

    International Nuclear Information System (INIS)

    Wong, D.; Lyons, M.; Burridge, L.; Lee, K.

    2010-01-01

    This study investigated the fertilization and hatching success of Atlantic cod (Gadus morhua) eggs that were exposed to various dilutions of produced water from a natural gas production platform. A control group of eggs was fertilized in sea water without any produced water. Another set of eggs were fertilized in sea water with 4 different concentrations of produced water and held their respective concentrations for 24 hours to evaluate the success of the fertilization. Viable fertilized eggs were transferred to 96 well plates containing fresh sea water and incubated in the dark at approximately 6 degrees C until hatch. Eggs began hatching about 14 days after fertilization (DPF), peaked at about 17 DPF, then finished hatching by 21 DPF. Analysis of PAH content in the diluted produced water showed that at 0.32 percent, 1.08 percent and 3.6 percent concentrations, the fertilization success was greater than or equal to that of the control group. However, for the 12 percent concentration, there were no viable fertilized eggs present after the 24 hour period. Survivability of eggs during sea water incubation was similar for the 0 percent, 0.32 percent and 1.08 percent treatment groups, but egg mortality increased for the 3.60 percent concentration group, to about 61.5 percent mean cumulative mortality at 6 DPF, then remained constant. The mean hatching success for all dilutions was presented.

  9. Preliminary Valuation of “Y” and “V”-Trellised Canopies for Mechanical Harvesting of Plums, Sweet Cherries and Sour Cherries for the Fresh Market

    Directory of Open Access Journals (Sweden)

    Rabcewicz Jacek

    2017-12-01

    Full Text Available Plums, sweet cherry, and sour cherry trees were spaced 4.5 m × 1.5 m to be trained to “Y” and “V”-trellising systems for mechanical harvesting, with a canopy contact harvester, attending to obtain fruits meeting the requirements of the fresh fruit market. The applied trellising systems were compared with the standard central leader system at the same spacing. The most of trellised trees grew less vigorously than the standard trees, and after 3 years of training, the trees were suitable for mechanical harvesting with the harvester designed at the Research Institute of Horticulture in Skierniewice. The trellised trees were able to set as many fruitlets as those grown in the form of central leader and gave a comparable yield, but differences between cultivars were significant. Light interception in the third year after planting was lower for trees of sour cherry and plum growing in the “Y”-20° and “V” in comparison to the trees with central leader. Illumination of trellised canopies at the level of 0.7 and 1.5 m was the most favorable in “V” system when compared to control and “Y” training systems. Cost of construction for the trellising systems of stone fruits calculated per 1 ha was two times higher when compared with the standard system.

  10. Evaporative processes for desalination of produced water; Processos evaporativos para dessalinizacao de agua produzida a fins de reuso

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Vivian T.; Dezotti, Marcia W. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE). Programa de Engenharia Quimica; Schuhli, Juliana B.; Gomes, Marcia T.; Pereira Junior, Oswaldo A. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2008-07-01

    During the productive life of an oil well, it gets the moment when a big quantity of produced water comes together with the oil. It can achieve 99% in the end of its economical life. The thermal desalination of the formation water is one of the most common technologies for achieving its reuse. This way, it was constructed one 'Robert' evaporator. The tests used different sodium chloride concentrations from 2,000 mg/L to 80,000 mg/L simulating concentrations found in the produced water from PETROBRAS wells. The tests were conducted in three different vacuum pressures. It was observed, increasing the vacuum applied to the system, results in reduction of solution boiling point. The salt concentrations of the brine blowdown were influenced by the sodium chloride concentration at the feed flow, by the vacuum applied to the system and, consequently, by the solution boiling point and flow rates. The produced distillate water presented sodium chloride concentration lower than 2 mg/L, indicating that this system can produce water to reuse in irrigation. (author)

  11. Water Kefir grain as a source of potent dextran producing lactic acid bacteria

    Directory of Open Access Journals (Sweden)

    Davidović Slađana Z.

    2015-01-01

    Full Text Available Water kefir is abeverage fermented by a microbial consortium captured in kefir grains. The kefir grains matrix is composed of polysaccharide, primarily dextran, whichis produced by members of the microbial consortium. In this study, we have isolated lactic acid bacteria (LAB from non-commercial water kefir grains (from Belgrade, Serbia and screened for dextran production. Among twelve Lisolates threeproduced slime colonies on modified MRS (mMRS agar containing sucrose instead of glucoseand were presumed to produce dextran. Three LABwere identified based on morphological, physiological and biochemical characteristics and 16S rRNA sequencing as Leuconostoc mesenteroides(strains T1 and T3 and Lactobacillus hilgardii (strain T5. The isolated strains were able to synthesize a substantial amount of dextran in mMRS broth containing 5% sucrose. Maximal yields (11.56, 18.00 and 18.46 g/l were obtained after 16h, 20h and 32h for T1, T3 and T5, respectively. Optimal temperature for dextran production was 23oC for two Leuconostoc mesenteroides strains and 30oC for Lactobacillus hilgardii strain. The produced dextrans were identified based on paper chromatography while the main structure characteristics of purified dextranwere observed by FT-IR spectroscopy. Our study shows that water kefir grains are a natural source of potent dextranproducing LAB. [Projekat Ministarstva nauke Republike Srbije, br. TR 31035

  12. Sensory and chromatographic evaluations of water soluble fractions from air-dried sausages

    DEFF Research Database (Denmark)

    Henriksen, Anders Peter; Stahnke, Marie Louise Heller

    1997-01-01

    Low molecular weight water soluble compounds were extracted from Danish salami, Italian sausage, and Spanish Chorizo. The extracts were fractionated by gel filtration chromatography revealing peptides with a molecular weight less than 4200 Dalton. Fractions consisting of smaller peptides and free...... amino acids had enhanced savory taste impressions described as mainly bouillon, bitter, sour, salty and plastic with odor notes of boiled potato. Determination of amino acids in the fractions before and after hydrolysis revealed the presence of mainly hydrophilic peptides in all fractions. Partial least...

  13. Detection and partial molecular characterization of atypical plum pox virus isolates from naturally infected sour cherry.

    Science.gov (United States)

    Chirkov, Sergei; Ivanov, Peter; Sheveleva, Anna

    2013-06-01

    Atypical isolates of plum pox virus (PPV) were discovered in naturally infected sour cherry in urban ornamental plantings in Moscow, Russia. The isolates were detected by polyclonal double antibody sandwich ELISA and RT-PCR using universal primers specific for the 3'-non-coding and coat protein (CP) regions of the genome but failed to be recognized by triple antibody sandwich ELISA with the universal monoclonal antibody 5B and by RT-PCR using primers specific to for PPV strains D, M, C and W. Sequence analysis of the CP genes of nine isolates revealed 99.2-100 % within-group identity and 62-85 % identity to conventional PPV strains. Phylogenetic analysis showed that the atypical isolates represent a group that is distinct from the known PPV strains. Alignment of the N-terminal amino acid sequences of CP demonstrated their close similarity to those of a new tentative PPV strain, CR.

  14. Effect of Fermentation and Cooking on Soluble and Bound Phenolic Profiles of Finger Millet Sour Porridge.

    Science.gov (United States)

    Gabaza, Molly; Shumoy, Habtu; Muchuweti, Maud; Vandamme, Peter; Raes, Katleen

    2016-10-12

    The aim of this study was to evaluate the soluble and bound phenolic content of finger millet and the impact of process induced changes on phenolic profiles of their sour porridge. Finger millet porridge and intermediate products were collected from four groups of households in the Hwedza communal area, Zimbabwe, after which soluble and bound phenolic compounds (PC) including condensed tannins (CT) were quantified. Bound PC and CT contributed 95% of the total PC and CT. The CT were only detected in the red varieties. Major individual PC identified were catechin occurring in the soluble fraction only, while ferulic, sinapic, and salicylic acid were mainly present in the bound fraction. Fermentation and cooking caused a more than 2-fold increase in soluble PC, CT, and individual PC. Improved traditional processing techniques optimized for improved bioavailability and health benefits of phenolics are highly relevant for the low income populations.

  15. Evaluation of the process of coagulation/flocculation of produced water using Moringa oleifera Lam. as natural coagulant

    Energy Technology Data Exchange (ETDEWEB)

    Santana, C.R.; Pereira, D.F.; Sousa, S.C S N.; Silva, G.F. [Universidade Federal de Sergipe (UFSE), Sao Cristovao, SE (Brazil). Dept. de Engenharia Quimica], e-mail: claudia@ufs.br; Cavalcanti, E.B. [Universidade Tiradentes (UNIT), SE (Brazil). Inst. de Tecnologia e Pesquisa

    2010-07-15

    In the lifetime of an oil well, there comes a moment when a lot of water begins to be produced along with oil, either by the conditions of the reservoir, or as a result of water injection in the secondary recovery of the well. An important step in such process involves the treatment of the produced water by means of coagulation techniques. Therefore, the use of environmentally correct coagulants is presented as a viable alternative and has demonstrated advantages over the use of chemical coagulants. The plant of the genus Moringa, whose species is oleifera Lam, stands out as one of the most promising natural coagulants. The present study investigated the evaluation of the coagulation/flocculation of produced water, using seeds of Moringa oleifera Lam. as coagulant. The results were very significant, demonstrating that Moringa oleifera Lam. can be used as a natural coagulant in this type of treatment. (author)

  16. Removal of oil, grease, and suspended solids from produced water with ceramic crossflow microfiltration

    International Nuclear Information System (INIS)

    Chen, A.S.C.; Flynn, J.T.; Cook, R.G.; Casaday, A.L.

    1991-01-01

    In this paper results of studies of two onshore and two offshore pilot plants that use ceramic crossflow microfiltration (CCFM) to separate oil, grease, and suspended solids from produced water are discussed. The method is capable of producing permeate quality with < =5 mg/L (detection limit) of dispersed oil and grease and <1 mg/L of suspended solids

  17. Developing a cost effective environmental solution for produced water and creating a ''new'' water resource

    Energy Technology Data Exchange (ETDEWEB)

    Doran, Glenn; Leong, Lawrence Y.C.

    2000-05-01

    The project goal is to convert a currently usable by-product of oil production, produced water, into a valuable drinking water resource. The project was located at the Placate Oil Field in Santa Clarita, California, approximately 25 miles north of Los Angeles. The project included a literature review of treatment technologies; preliminary bench-scale studies to refine a planning level cost estimate; and a 10-100 gpm pilot study to develop the conceptual design and cost estimate for a 44,000 bpd treatment facility. A reverse osmosis system was constructed, pilot tested, and the data used to develop a conceptual design and operation of four operational scenarios, two industrial waters levels and two irrigation/potable water.

  18. Application of ceramic membranes to SAGD produced water treatment for enhanced recycle and reuse

    Energy Technology Data Exchange (ETDEWEB)

    Minnich, K. [Veolia Water Solutions and Technologies, Mississauga, ON (Canada)

    2009-07-01

    Drivers for using ceramic membranes in steam assisted gravity drainage (SAGD) include reduced investment cost; alternative treatment technologies that reduce energy and greenhouse gas emissions; and ceramic membranes can be chemically and steam cleaned. This presentation discussed the application of ceramic membranes to SAGD produced water treatment for enhanced recycle and reuse. The presentation illustrated conventional ceramic membranes as well as surface enhanced membranes and provided background information on oil separation. Other topics that were discussed included issues regarding desalter bottoms de-oiling; challenges in de-oiling oil sands produced water; CeraMem surface enhanced membranes; surface facilities and ceramic membrane opportunities; and water treatment using ceramic membranes. The presentation concluded with a discussion of the application of ceramic membranes to SAGD next steps such as a demonstration test of industrial prototype membranes for de-oiling, and pilot testing of ceramic desilication. tabs., figs.

  19. Degradation of Total Petroleum Hydrocarbon and BTEX Compounds in Produced Water

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, Lorri

    2002-04-01

    Petroleum Environmental Technologies, LLC entered into a Cooperative Research and Development agreement with the Rocky Mountain Oilfield Testing Center to an in-situ pit treatment demonstration and produced water treatment demonstration. The purpose of the test is to demonstrate the degradation of petroleum hydrocarbon compounds in soil and aqueous matrices where ECOSAFE is applied to enhance the degradation of these contaminants.

  20. Developing County-level Water Footprints of Biofuel Produced from Switchgrass and Miscanthus x Giganteus in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Wu, May M. [Argonne National Lab. (ANL), Argonne, IL (United States); Chiu, Yi-Wen [Argonne National Lab. (ANL), Argonne, IL (United States)

    2014-09-30

    Perennial grass has been proposed as a potential candidate for producing cellulosic biofuel because of its promising productivity and benefits to water quality, and because it is a non-food feedstock. While extensive research focuses on selecting and developing species and conversion technologies, the impact of grass-based biofuel production on water resources remains less clear. As feedstock growth requires water and the type of water consumed may vary considerably from region to region, water use must be characterized with spatial resolution and on a fuel production basis. This report summarizes a study that assesses the impact of biofuel production on water resource use and water quality at county, state, and regional scales by developing a water footprint of biofuel produced from switchgrass and Miscanthus × giganteus via biochemical conversion.

  1. Integration of Thermoelectric Generators and Wood Stove to Produce Heat, Hot Water, and Electrical Power

    Science.gov (United States)

    Goudarzi, A. M.; Mazandarani, P.; Panahi, R.; Behsaz, H.; Rezania, A.; Rosendahl, L. A.

    2013-07-01

    Traditional fire stoves are characterized by low efficiency. In this experimental study, the combustion chamber of the stove is augmented by two devices. An electric fan can increase the air-to-fuel ratio in order to increase the system's efficiency and decrease air pollution by providing complete combustion of wood. In addition, thermoelectric generators (TEGs) produce power that can be used to satisfy all basic needs. In this study, a water-based cooling system is designed to increase the efficiency of the TEGs and also produce hot water for residential use. Through a range of tests, an average of 7.9 W was achieved by a commercial TEG with substrate area of 56 mm × 56 mm, which can produce 14.7 W output power at the maximum matched load. The total power generated by the stove is 166 W. Also, in this study a reasonable ratio of fuel to time is described for residential use. The presented prototype is designed to fulfill the basic needs of domestic electricity, hot water, and essential heat for warming the room and cooking.

  2. Produced water treatment and discharge solutions in TRANSPETRO maritime terminals; Solucoes de tratamento e descarte de agua produzida nos terminais aquaviarios da TRANSPETRO

    Energy Technology Data Exchange (ETDEWEB)

    Mansor, Leonardo Mitidiero; Burburan, Alexandre; Rodrigues, Fernanda Fonseca; Cerqueira, Ana Claudia F.P. de [TRANSPETRO - PETROBRAS Transporte S.A., Rio de Janeiro, RJ (Brazil); Padilha, Carlos Frederico [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2008-07-01

    The PETROBRAS produced water programme, conducted by PETROBRAS S.A. is the response to the challenge faced in handling, treating and discharging produced water associated to oil production that comes from Campos Basin mainly. After run modeling studies in oil and produced water associated through 2015 scenario, it was identified the total amount of produced water that will be handle monthly, increasing from 215.000 m{sup 3} up to 420.000 m{sup 3}. To achieve the goals of treating e discharging that huge amount of water, the program understood the following main actions: built 5 produced water plants (Sao Sebastiao, Macae-Cabiunas, Angra dos Reis, Sao Francisco do Sul and Osorio) and 2 reinjection sites (Cabiunas and Lagoa Parda). These plants and sites will be able to treat monthly the total produced water amount of 677.000 m{sup 3}. (author)

  3. Application of water-assisted ultraviolet light in combination of chlorine and hydrogen peroxide to inactivate Salmonella on fresh produce.

    Science.gov (United States)

    Guo, Shuanghuan; Huang, Runze; Chen, Haiqiang

    2017-09-18

    With the demand for fresh produce increases in recent decades, concerns for microbiological safety of fresh produce are also raised. To identify effective ultraviolet (UV) light treatment for fresh produce decontamination, we first determined the effect of three forms of UV treatment, dry UV (samples were treated by UV directly), wet UV (samples were dipped in water briefly and then exposed to UV), and water-assisted UV (samples were treated by UV while being immersed in agitated water) on inactivation of Salmonella inoculated on tomatoes and fresh-cut lettuce. In general, the water-assisted UV treatment was found to be the most effective for both produce items. Chlorine and hydrogen peroxide were then tested to determine whether they could be used to enhance the decontamination efficacy of water-assisted UV treatment and prevent transfer of Salmonella via wash water by completely eliminating it. Neither of them significantly enhanced water-assisted UV inactivation of Salmonella on tomatoes. Chlorine significantly improved the decontamination effectiveness of the water-assisted UV treatment for baby-cut carrots and lettuce, but not for spinach. In general, the single water-assisted UV treatment and the combined treatment of water-assisted UV and chlorine were similar or more effective than the chlorine washing treatment. In most of the cases, no Salmonella was detected in the wash water when the single water-assisted UV treatment was used to decontaminate tomatoes. In a few cases when Salmonella was detected in the wash water, the populations were very low,≤2CFU/mL, and the wash water contained an extremely high level of organic load and soil level. Therefore, the single water-assisted UV treatment could potentially be used as an environmentally friendly and non-chemical alternative to chlorine washing for tomatoes after validation in industrial scale. For lettuce, spinach and baby-cut carrots, the combined treatment of water-assisted UV treatment and chlorine

  4. Immune modulation in the blue mussel Mytilus edulis exposed to North Sea produced water

    Energy Technology Data Exchange (ETDEWEB)

    Hannam, M.L., E-mail: marie.hannam@plymouth.ac.u [Ecotoxicology and Stress Biology Research Centre, School of Biological Sciences, University of Plymouth, Drake Circus, Plymouth, Devon, PL4 8AA (United Kingdom); Bamber, S.D.; Sundt, R.C. [IRIS - Biomiljo, Mekjarvik 12, 4070 Randaberg (Norway); Galloway, T.S. [School of Biosciences, University of Exeter, Hatherly Laboratories, Prince of Wales Road, Exeter, EX4 4PS (United Kingdom)

    2009-06-15

    The discharge of oil well produced water (PW) provides a constant source of contaminants to the marine environment including polycyclic aromatic hydrocarbons, alkylated phenols, metals and production chemicals. High concentrations of PW cause adverse effects to exposed biota, including reduced survival, growth and reproduction. Here we explore the effects of PW on immune function in the blue mussel, Mytilus edulis. Mussels were exposed for 21 days to sublethal PW concentrations (0.125-0.5%) and cellular parameters were measured. Cell viability, phagocytosis and cytotoxicity were inhibited after exposure to 0.25% and 0.5% PW, whilst the 0.125% PW treatment produced significant increases in these biomarker responses. This biphasic response was only observed after 7 days exposure; longer exposure periods led to a reduction in immune parameters. Results indicate that PW concentrations close to the discharge point cause modulation to cellular immunity. The implications for longer-term disease resistance are discussed. - Exposure to produced water alters immune function in the sentinel species Mytilus edulis.

  5. Immune modulation in the blue mussel Mytilus edulis exposed to North Sea produced water

    International Nuclear Information System (INIS)

    Hannam, M.L.; Bamber, S.D.; Sundt, R.C.; Galloway, T.S.

    2009-01-01

    The discharge of oil well produced water (PW) provides a constant source of contaminants to the marine environment including polycyclic aromatic hydrocarbons, alkylated phenols, metals and production chemicals. High concentrations of PW cause adverse effects to exposed biota, including reduced survival, growth and reproduction. Here we explore the effects of PW on immune function in the blue mussel, Mytilus edulis. Mussels were exposed for 21 days to sublethal PW concentrations (0.125-0.5%) and cellular parameters were measured. Cell viability, phagocytosis and cytotoxicity were inhibited after exposure to 0.25% and 0.5% PW, whilst the 0.125% PW treatment produced significant increases in these biomarker responses. This biphasic response was only observed after 7 days exposure; longer exposure periods led to a reduction in immune parameters. Results indicate that PW concentrations close to the discharge point cause modulation to cellular immunity. The implications for longer-term disease resistance are discussed. - Exposure to produced water alters immune function in the sentinel species Mytilus edulis.

  6. Occurrence of perfluoroalkyl substances (PFAS) in garden produce at homes with a history of PFAS-contaminated drinking water.

    Science.gov (United States)

    Scher, Deanna P; Kelly, James E; Huset, Carin A; Barry, Kitrina M; Hoffbeck, Richard W; Yingling, Virginia L; Messing, Rita B

    2018-04-01

    The decades-long disposal of manufacturing waste containing perfluoroalkyl substances (PFAS) in landfills resulted in contamination of groundwater serving as the drinking water supply for the eastern Twin Cities metropolitan region. While measures were taken to reduce the levels of PFAS in the drinking water, questions remained about possible non-drinking water pathways of exposure in these communities. The Minnesota Department of Health (MDH) investigated whether PFAS in water used for yard and garden irrigation results in elevated concentrations of PFAS in soil and home-grown produce. In 2010, samples of outdoor tap water, garden soil, and garden produce were collected at homes impacted by the contamination and analyzed for several PFAS. Perfluorobutanoic acid (PFBA) was the primary PFAS present in water, followed by perfluoropentanoic acid (PFPeA). Although PFBA, perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) were present in 100% of soil samples at higher concentrations compared to other PFAS, only PFBA was readily translocated to plants. Significant determinants of PFBA concentration in produce were the amount of PFBA applied to the garden via watering and the type of produce tested. Results from this real-world study are consistent with experimental findings that short-chain PFAS have the highest potential to translocate to and bioaccumulate in edible plants. These findings are globally relevant, as short-chain PFAS serve as commercial substitutes for longer-chain compounds and are increasingly detected in water due to their relatively high solubility and mobility. Copyright © 2018 Elsevier Ltd. All rights reserved.

  7. Drinking water purification by electrosynthesis of hydrogen peroxide in a power-producing PEM fuel cell.

    Science.gov (United States)

    Li, Winton; Bonakdarpour, Arman; Gyenge, Előd; Wilkinson, David P

    2013-11-01

    The industrial anthraquinone auto-oxidation process produces most of the world's supply of hydrogen peroxide. For applications that require small amounts of H2 O2 or have economically difficult transportation means, an alternate, on-site H2 O2 production method is needed. Advanced drinking water purification technologies use neutral-pH H2 O2 in combination with UV treatment to reach the desired water purity targets. To produce neutral H2 O2 on-site and on-demand for drinking water purification, the electroreduction of oxygen at the cathode of a proton exchange membrane (PEM) fuel cell operated in either electrolysis (power consuming) or fuel cell (power generating) mode could be a possible solution. The work presented here focuses on the H2 /O2 fuel cell mode to produce H2 O2 . The fuel cell reactor is operated with a continuous flow of carrier water through the cathode to remove the product H2 O2 . The impact of the cobalt-carbon composite cathode catalyst loading, Teflon content in the cathode gas diffusion layer, and cathode carrier water flowrate on the production of H2 O2 are examined. H2 O2 production rates of up to 200 μmol h(-1)  cmgeometric (-2) are achieved using a continuous flow of carrier water operating at 30 % current efficiency. Operation times of more than 24 h have shown consistent H2 O2 and power production, with no degradation of the cobalt catalyst. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Effects of untreated and treated oilfield-produced water on seed germination, seedling development, and biomass production of sunflower (Helianthus annuus L.).

    Science.gov (United States)

    da Costa Marques, Mônica Regina; de Souza, Paulo Sérgio Alves; Rigo, Michelle Machado; Cerqueira, Alexandre Andrade; de Paiva, Julieta L; Merçon, Fábio; Perez, Daniel Vidal

    2015-10-01

    This study aims to evaluate possible toxic effects of oil and other contaminants from oilfield-produced water from oil exploration and production, on seed germination, and seedling development of sunflower (Helianthus annuus L.). In comparison, as treated by electroflocculation, oilfield-produced water, with lower oil and organic matter content, was also used. Electroflocculation treatment of oilfield-produced water achieved significant removals of chemical oxygen demand (COD) (94 %), oil and grease (O&G) (96 %), color (97 %), and turbidity (99 %). Different O&G, COD, and salt levels of untreated and treated oilfield-produced water did not influence germination process and seedling biomass production. Normal seedlings percentage and vigor tended to decrease more intensely in O&G and COD levels, higher than 337.5 mg L(-1) and 1321 mg O2 L(-1), respectively, using untreated oilfield-produced water. These results indicate that this industrial effluent must be treated, in order to not affect adversely seedling development. This way, electroflocculation treatment appears as an interesting alternative to removing oil and soluble organic matter in excess from oilfield-produced water improving sunflower's seedling development and providing a friendly environmental destination for this wastewater, reducing its potential to harm water resources, soil, and biota.

  9. Long-term biomonitoring of a produced water discharge from the Cedar Cove degasification field, Alabama. January 1991

    Energy Technology Data Exchange (ETDEWEB)

    O' Neil, P.E.; Harris, S.C.; Mettee, M.F.; McGregor, S.W.; Shepard, T.E.

    1991-01-01

    Development of coalbed methane has become a major industry for the state of Alabama. In excess of 1,300 wells were producing methane by the end of July 1990. A byproduct of methane production is produced water containing elevated concentrations of chloride, sodium, iron and bicarbonate. These waters are currently permitted for discharge into streams or as a land application. The purpose of the study was to examine the long-term impacts of produced waters to streams relative to water-quality changes and aquatic biological effects. Distinct water-quality changes in the receiving stream were documented and consisted primarily of increased dissolved solids, changes in the pH regime and changes in the carbonate buffering system. In contrast, no significant or consistent detrimental change in the structure or function of the stream biological community could be detected. Subtle changes in biological community structure and composition were noted and most likely due to effects associated with algal productivity in settling lagoons. These changes, however, were within the boundaries of variation typically observed for the communities. Based on the results of this and earlier studies, it was concluded that the national water-quality criterion for chloride was protective of stream life as examined in the study.

  10. Water Footprint of Milk Produced and Processed in South Africa: Implications for Policy-Makers and Stakeholders along the Dairy Value Chain

    Directory of Open Access Journals (Sweden)

    Enoch Owusu-Sekyere

    2016-07-01

    Full Text Available The current water scarcity situation in South Africa is a threat to sustainable development. The present paper has assessed the water footprint of milk produced and processed in South Africa using the procedures outlined in the water footprint assessment manual. The results show that 1352 m3 of water is required to produce one tonne of milk with 4% fat and 3.3% protein in South Africa. The water used in producing feed for lactating cows alone accounts for 86.35% of the total water footprint of milk. The water footprint of feed ration for lactating cows is about 85% higher than that of non-lactating cows. Green water footprint accounts for more than 86% of the total water footprint of feed ration for lactating cows. Green and blue water footprints are the highest contributors to the total water footprint milk production in South Africa. Water used for feed production for both lactating and non-lactating cows accounts for about 99% of the total water footprint of milk production in South Africa. Particular attention should be given to feed crops with low water footprints and high contribution to dry matter to provide balanced ration with low water footprint. Water users, managers and livestock producers should pay attention to green and blue water consumption activities along the milk value chain and design strategies to minimize them. Corn, sorghum and lucerne production under irrigation in the greater Orange River basin is sustainable, whereas oats production for silage in the same catchment area is not sustainable. Our findings provide the rationale for dairy producers and water users in the dairy industry to get an understanding of the degree of sustainability of their input and output combinations, production choices, and policy interventions, in terms of water use.

  11. Utilization of solar energy in the photodegradation of gasoline in water and of oil-field-produced water.

    Science.gov (United States)

    Moraes, José Ermírio F; Silva, Douglas N; Quina, Frank H; Chiavone-Filho, Osvaldo; Nascimento, Cláudio Augusto O

    2004-07-01

    The photo-Fenton process utilizes ferrous ions (Fe2+), hydrogen peroxide (H2O2), and ultraviolet (UV) irradiation as a source of hydroxyl radicals for the oxidation of organic matter present in aqueous effluents. The cost associated with the use of artificial irradiation sources has hindered industrial application of this process. In this work, the applicability of solar radiation for the photodegradation of raw gasoline in water has been studied. The photo-Fenton process was also applied to a real effluent, i.e., oil-field-produced water, and the experimental results demonstrate the feasibility of employing solar irradiation to degrade this complex saturated-hydrocarbon-containing system.

  12. State of the art of produced water treatment.

    Science.gov (United States)

    Jiménez, S; Micó, M M; Arnaldos, M; Medina, F; Contreras, S

    2018-02-01

    Produced water (PW) is the wastewater generated when water from underground reservoirs is brought to the surface during oil or gas extraction. PW is generated in large amounts and has a complex composition, containing various toxic organic and inorganic compounds. PW is currently treated in conventional trains that include phase separators, decanters, cyclones and coarse filters in order to comply with existing regulation for discharge. These treatment trains do not achieve more restrictive limitations related to the reuse of the effluent (reinjection into extraction wells) or other beneficial uses (e.g., irrigation). Therefore, and to prevent environmental pollution, further polishing processes need to be carried out. Characterization of the PW to determine major constituents is the first step to select the optimum treatment for PW, coupled with environmental factors, economic considerations, and local regulatory framework. This review tries to provide an overview of different treatments that are being applied to polish this type of effluents. These technologies include membranes, physical, biological, thermal or chemical treatments, where special emphasis has been made on advanced oxidation processes due to the advantages offered by these processes. Commercial treatments, based on the combination, modification and improvement of simpler treatments, were also discussed. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Quantitative produced water analysis using mobile 1H NMR

    International Nuclear Information System (INIS)

    Wagner, Lisabeth; Fridjonsson, Einar O; May, Eric F; Stanwix, Paul L; Graham, Brendan F; Carroll, Matthew R J; Johns, Michael L; Kalli, Chris

    2016-01-01

    Measurement of oil contamination of produced water is required in the oil and gas industry to the (ppm) level prior to discharge in order to meet typical environmental legislative requirements. Here we present the use of compact, mobile 1 H nuclear magnetic resonance (NMR) spectroscopy, in combination with solid phase extraction (SPE), to meet this metrology need. The NMR hardware employed featured a sufficiently homogeneous magnetic field, such that chemical shift differences could be used to unambiguously differentiate, and hence quantitatively detect, the required oil and solvent NMR signals. A solvent system consisting of 1% v/v chloroform in tetrachloroethylene was deployed, this provided a comparable 1 H NMR signal intensity for the oil and the solvent (chloroform) and hence an internal reference 1 H signal from the chloroform resulting in the measurement being effectively self-calibrating. The measurement process was applied to water contaminated with hexane or crude oil over the range 1–30 ppm. The results were validated against known solubility limits as well as infrared analysis and gas chromatography. (paper)

  14. Comparison of the secondary electrons produced by proton and electron beams in water

    Energy Technology Data Exchange (ETDEWEB)

    Kia, Mohammad Reza, E-mail: m-r-kia@aut.ac.ir; Noshad, Houshyar [Department of Energy Engineering and Physics, Amirkabir University of Technology (Tehran Polytechnic), P.O. Box 15875-4413, Hafez Avenue, Tehran (Iran, Islamic Republic of)

    2016-05-15

    The secondary electrons produced in water by electron and proton beams are compared with each other. The total ionization cross section (TICS) for an electron impact in water is obtained by using the binary-encounter-Bethe model. Hence, an empirical equation based on two adjustable fitting parameters is presented to determine the TICS for proton impact in media. In order to calculate the projectile trajectory, a set of stochastic differential equations based on the inelastic collision, elastic scattering, and bremsstrahlung emission are used. In accordance with the projectile trajectory, the depth dose deposition, electron energy loss distribution in a certain depth, and secondary electrons produced in water are calculated. The obtained results for the depth dose deposition and energy loss distribution in certain depth for electron and proton beams with various incident energies in media are in excellent agreement with the reported experimental data. The difference between the profiles for the depth dose deposition and production of secondary electrons for a proton beam can be ignored approximately. But, these profiles for an electron beam are completely different due to the effect of elastic scattering on electron trajectory.

  15. Candidate for solar power: a novel desalination technology for coal bed methane produced water

    International Nuclear Information System (INIS)

    Sattler, Allan; Hanley, Charles; Hightower, Michael; Wright, Emily; Wallace, Sam; Pohl, Phillip; Donahe, Ryan; Andelman, Marc

    2006-01-01

    Laboratory and field developments are underway to use solar energy to power a desalination technology - capacitive deionization - for water produced by remote Coal Bed Methane (CBM) natural gas wells. Due to the physical remoteness of many CBM wells throughout the Southwestern U>S> as shown in Figure 1, this approach may offer promise. This promise is not only from its effectiveness in removing salt from CBM water and allowing it to be utilized for various applications, but also for its potentially lower energy consumption compared Figure 1: Candidate remote well sites for planned field implementation of new PV-powered desalination process: (a) Raton Basin and (b) San Juan Basin, New Mexico to other technologies, such as reverse osmosis. This coupled with the remoteness (Figure 1) of thousands these wells, makes them more feasible for use with photovoltaic (solar, electric, PV) systems. Concurrent laboratory activities are providing information about the effectiveness of this technology and of the attender energy requirements of this technology under various produced water qualities and water reuse applications, such as salinity concentrations and water flows. These parameters are being used to drive the design of integrated PV-powered desalination systems. Full-scale field implementations are planned, with data collection and analysis designed to optimize the system design for practical remote applications. Earlier laboratory (and very recent laboratory) studies of capacitive deionization have shown promise at common CBM salinity levels. The technology may require less energy. be less susceptible to fouling and is more compact than equivalent reverse osmosis (RO) systems. The technology uses positively and negatively charged electrodes to attract charged ions in a liquid, such as dissolved salts, metals, and some organics, to the electrodes. This concentrates the ions at the electrodes and reduced the ion concentrations in the liquid. This paper discusses the

  16. Electron spin resonance of the solvation of radiation-produced silver atoms in alcohol-water mixtures

    International Nuclear Information System (INIS)

    Li, A.S.W.; Kevan, L.

    1982-01-01

    Frozen solutions of silver salts exposed to 60 Co γ-irradiation form silver atoms by reaction of radiation-produced electrons with the silver ion. At 4 K the silver atoms are initially produced in a nonequilibrium or presolvated state and upon brief thermal excitation to 77 K the first solvation shell geometry changes towards an equilibrium or solvated silver atom. This is most pronounced in water but also occurs in methanol, ethanol and n-propanol matrices. The changes in the electron spin resonance magnetic parameters upon silver atom solvation have been determined. In alcohol-water mixtures Ag 0 is preferentially solvated by polycrystalline water at low alcohol concentration. Above a particular alcohol mole percent Ag 0 suddenly changes its environment to a glassy alcohol one. This sudden change occurs at 17, 13 and 6 mol % methanol, ethanol and n-propanol, respectively. These mole percents correlate with the minimum of the excess enthalpy of mixing and with the hydrogen atom trapping ability of these alcohol-water mixtures. The results also suggest that the local environmental disorder around Ag 0 increases with alcohol chain length in alcohol-water frozen solutions. (author)

  17. In situ and laboratory toxicity of coalbed natural gas produced waters with elevated sodium bicarbonate

    Science.gov (United States)

    Farag, Aïda M.; Harper, David D.; Skaar, Don

    2014-01-01

    Some tributaries in the Powder River Structural Basin, USA, were historically ephemeral, but now contain water year round as a result of discharge of coalbed natural gas (CBNG)-produced waters. This presented the opportunity to study field sites with 100% effluent water with elevated concentrations of sodium bicarbonate. In situ experiments, static renewal experiments performed simultaneously with in situ experiments, and static renewal experiments performed with site water in the laboratory demonstrated that CBNG-produced water reduces survival of fathead minnow (Pimephales promelas) and pallid sturgeon (Scaphirhynchus albus). Age affected survival of fathead minnow, where fish 2 d posthatch (dph) were more sensitive than 6 dph fish, but pallid sturgeon survival was adversely affected at both 4 and 6 dph. This may have implications for acute assays that allow for the use of fish up to 14 dph. The survival of early lifestage fish is reduced significantly in the field when concentrations of NaHCO3 rise to more than 1500 mg/L (also expressed as >1245 mg HCO3 (-) /L). Treatment with the Higgin's Loop technology and dilution of untreated water increased survival in the laboratory. The mixing zones of the 3 outfalls studied ranged from approximately 800 m to 1200 m below the confluence. These experiments addressed the acute toxicity of effluent waters but did not address issues related to the volumes of water that may be added to the watershed.

  18. Highly cost-effective and sulfur/coking resistant VOx-grafted TiO2 nanoparticles as an efficient anode catalyst for direct conversion of dry sour methane in solid oxide fuel cells

    NARCIS (Netherlands)

    Garcia, A.; Yan, N.; Vincent, A.; Singh, A.; Hill, J.M.; Chuang, K. T.; Luo, J.L.

    2015-01-01

    In this work, we show that grafted metal oxide can be a highly cost-effective and active anode for solid oxide fuel cells for sour methane conversion. The developed electro-catalyst was composed of vanadium oxide grafted TiO2 nanoparticles (VOx/TiO2) infiltrated into a porous La0.4Sr0.5Ba0.1TiO3+δ

  19. Decision 99-13: Crestar Energy Inc. applications to construct and operate sour gas batteries and pipelines, Vulcan Field

    International Nuclear Information System (INIS)

    1999-06-01

    On 1 December 1998, the applicant applied pursuant to Part 4 of the Pipeline Act and Section 7.001 of the Oil and Gas Conservation Regulations for approval to construct and operate a sour gas pipeline and various surface facilities to tie in three wells. These are located at Legal Subdivision 12 of Section 36, Township 16, Range 24, West of the fourth Meridian (12-36 facility), Lsd 10-35-16-24 WM4 (10-35 facility), and Lsd 7-26-16-24 WM4 (7-26 facility), to an existing pipeline and proposed surface facility at Lsd 16-16-16-24 WM4. The 10-35, 7-26 and 16-16 facilities would each have a separator, a flare knockout drum, and a flare stack. The 12-36 facility would have two separators, one for each of the two producing zones at the 12-36 facility, a flare knockout drum, and flare stack. A compressor would be installed at the 16-16 facility. All fluids would be measured and re-injected into the pipeline for removal at the 16-16 facility. All proposed flare stacks would consists of a continuously burning sweet gas pilot and would be used for emergencies, routine well servicing, and pigging operations only. The pipeline would be designated as a Level 1 facility, and would transport up to 18 moles of hydrogen sulfide per kilomole of natural gas. Although the Board approved Application No. 1037084 after carefully considering the evidence, subject to meeting all the regulatory requirements and conditions set out in Attachment 1, it rejected Application No. 1033453

  20. Fast Lemons and Sour Boulders: Testing Crossmodal Correspondences Using an Internet-Based Testing Methodology

    Directory of Open Access Journals (Sweden)

    Andy T. Woods

    2013-09-01

    Full Text Available According to a popular family of hypotheses, crossmodal matches between distinct features hold because they correspond to the same polarity on several conceptual dimensions (such as active–passive, good–bad, etc. that can be identified using the semantic differential technique. The main problem here resides in turning this hypothesis into testable empirical predictions. In the present study, we outline a series of plausible consequences of the hypothesis and test a variety of well-established and previously untested crossmodal correspondences by means of a novel internet-based testing methodology. The results highlight that the semantic hypothesis cannot easily explain differences in the prevalence of crossmodal associations built on the same semantic pattern (fast lemons, slow prunes, sour boulders, heavy red; furthermore, the semantic hypothesis only minimally predicts what happens when the semantic dimensions and polarities that are supposed to drive such crossmodal associations are made more salient (e.g., by adding emotional cues that ought to make the good/bad dimension more salient; finally, the semantic hypothesis does not explain why reliable matches are no longer observed once intramodal dimensions with congruent connotations are presented (e.g., visually presented shapes and colour do not appear to correspond.

  1. Review of research on impacts to biota of discharges of naturally occurring radionuclides in produced water to the marine environment

    International Nuclear Information System (INIS)

    Hosseini, Ali; Brown, Justin E.; Gwynn, Justin P.; Dowdall, Mark

    2012-01-01

    Produced water has been described as the largest volume waste stream in the exploration and production process of oil and gas. It is accompanied by discharges of naturally occurring radionuclides raising concerns over the potential radiological impacts of produced water on marine biota. In the Northern European marine environment, radioactivity in produced water has received substantial attention owing to the OSPAR Radioactive Substances Strategy which aims at achieving ‘concentrations in the environment near background values for naturally occurring radioactive substances’. This review provides an overview of published research on the impacts to biota from naturally occurring radionuclides discharged in produced water by the offshore oil and gas industry. In addition to summarising studies and data that deal directly with the issue of dose and effect, the review also considers studies related to the impact of added chemicals on the fate of discharged radionuclides. The review clearly illustrates that only a limited number of studies have investigated possible impacts on biota from naturally occurring radionuclides present in produced water. Hence, although these studies indicate that the risk to the environment from naturally occurring radionuclides discharged in produced water is negligible, the substantial uncertainties involved in the assessments of impact make it difficult to be conclusive. With regard to the complexity involved in the problem under consideration there is a pressing need to supplement existing data and acquire new knowledge. Finally, the present work identifies some knowledge gaps to indicate future research requirements. -- Highlights: ► Produced water from offshore oil industry contains naturally occurring radionuclides. ► Published research on the impacts to biota from these radionuclides is reviewed. ► Review includes impact of added chemicals on the fate of discharged radionuclides. ► Studies indicate negligible risk to biota

  2. Fate and effects of nearshore discharges of OCS produced waters. Volume 2. Technical report (Final)

    International Nuclear Information System (INIS)

    Rabalais, N.N.; McKee, B.A.; Reed, D.J.; Means, J.C.

    1991-06-01

    While the number of facilities that discharge OCS produced waters into coastal environments of Louisiana are few in number, they account for large volumes, individually and collectively. Of the 15 facilities which discharge OCS-generated produced water into coastal environments of Louisiana (as of February 1990), 10 discharges in seven areas were studied. The discharge volumes of the study areas range from 3,000 to 106,000/bbl.d. The receiving environments for these effluents are varied, but include the shallow, nearshore continental shelf; high energy, freshwater distributaries of the Mississippi River delta; and brackish and saline coastal environments with moderately to poorly flushed waters. All study areas are within the Mississippi River Deltaic Plain. The study expanded on the initial assessment of Boesch and Rabalais (1989a) with increased temporal and spatial studies of three areas, additional study sites including an abandoned discharge, and additional analytical and field observations

  3. Biotransformation of arsenite and bacterial aox activity in drinking water produced from surface water of floating houses: Arsenic contamination in Cambodia

    International Nuclear Information System (INIS)

    Chang, Jin-Soo

    2015-01-01

    The potential arsenite bioteansformation activity of arsenic was investigated by examining bacterial arsenic arsenite-oxidizing gene such as aoxS, aoxR, aoxA, aoxB, aoxC, and aoxD in high arsenic-contaminated drinking water produced from the surface water of floating houses. There is a biogeochemical cycle of activity involving arsenite oxidase aox system and the ars (arsenic resistance system) gene operon and aoxR leader gene activity in Alcaligenes faecalis SRR-11 and aoxS leader gene activity in Achromobacter xylosoxidans TSL-66. Batch experiments showed that SRR-11 and TSL-66 completely oxidized 1 mM of As (III) to As (V) within 35–40 h. The leaders of aoxS and aoxR are important for gene activity, and their effects in arsenic bioremediation and mobility in natural water has a significant ecological role because it allows arsenite oxidase in bacteria to control the biogeochemical cycle of arsenic-contaminated drinking water produced from surface water of floating houses. - Highlights: • The aox genotype system activity and arsenite-oxidizing bacteria was studied. • High arsenic contamination affects the detoxification activities of aoxS and aoxM. • Much Cambodian drinking water has dangerously high arsenic contamination. • Disease-causing microorganisms were found in various drinking water sources. - The importance of this study is that it responds to the high concentrations of arsenic contamination that were found in the drinking water of floating-house residents with the following proposition: The combined periplasm activity of the aoxS and aoxR genes and arsenite oxidase reflects the arsenic oxidation potential of the aoxA, aoxB, aoxC, and aoxD systems in the surface water of floating houses in Cambodia.

  4. Potencial de obtenção de novos porta-enxertos em cruzamentos envolvendo limoeiro 'Cravo', laranjeira 'Azeda', tangerineira 'Sunki' e híbridos de Poncirus Trifoliata Potential of obtaining new rootstocks in crosses among 'Rangpur' lime, 'Sour' orange, 'Sunki' mandarin and Poncirus Trifoliata

    Directory of Open Access Journals (Sweden)

    Walter dos Santos Soares Filho

    2008-03-01

    Full Text Available O limoeiro 'Cravo' e a laranjeira 'Azeda' são importantes porta-enxertos de citros. Com o objetivo de explorar seu potencial genético, distintas seleções de limoeiro 'Cravo', empregadas como parentais femininos, foram cruzadas com seleções de laranjeira 'Azeda', tangerineira 'Sunki Maravilha' e híbridos de Poncirus trifoliata. Semelhantemente, seleções de 'Azeda' foram hibridadas com seleções de 'Cravo' e híbridos de P. trifoliata. Avaliaram-se a taxa de vingamento de frutos, a porcentagem de híbridos no conjunto total de indivíduos obtidos (zigóticos e nucelares, a altura e o diâmetro do caule destes, em torno dos 12 meses de idade. O cruzamento entre limoeiro 'Cravo', seleções comum e 'Santa Cruz', com tangerineira 'Sunki 'Maravilha' resultou nas maiores taxas de vingamento de frutos (média de 87,5% e maior percentual de híbridos (média de 64,0%, sendo estes relativamente vigorosos, segundo comparações com seedlings nucelares desse limoeiro. Quanto às hibridações envolvendo a laranjeira 'Azeda', mostraram-se promissoras 'Azeda Jacarandá' x (tangerineira 'Cleópatra' x P. trifoliata seleção 'Swingle 245', pela relativamente elevada taxa de vingamento de frutos (50%, boa porcentagem de híbridos (32,3% e possibilidade de obtenção de híbridos vigorosos, e laranjeira 'Azeda' comum x limoeiro 'Cravo' seleções comum e 'Santa Cruz', pela possibilidade de obtenção de híbridos vigorosos e em quantidades relativamente altas, em torno de 40% de plantas híbridas.'Rangpur' lime and 'Sour' orange are important citrus rootstocks. Aiming to explore their genetic potential, several 'Rangpur' lime selections, as female parents, were crossed with 'Sour' orange selections, 'Sunki Maravilha' mandarin and Poncirus trifoliata hybrids. In the same way, 'Sour' orange selections were crossed with 'Rangpur' lime selections and P. trifoliata hybrids. Parameters evaluated were: fruit set, percentage of hybrids out of the total number

  5. Characterization of water-in-oil emulsions produced with microporous hollow polypropylene fibers

    Directory of Open Access Journals (Sweden)

    HELMAR SCHUBERT

    2000-11-01

    Full Text Available The preparation of fine and monodispersed water-in-oil (W/O emulsions by utilizing hydrophobic hollow polypropylene fibers with 0.4 mm pores was investigated in this work. The experiments were carried out using demineralized water as the disperse phase, mineral oil Velocite No. 3 as the continuous phase, and polyglycerol polyricinoleate (PGPR 90 in the concentration range of 2.5 – 10 wt % as the oil-soluble emulsifier. The size of the water droplets in the prepared emulsions and the droplet size distribution strongly depend on the content of the disperse phase, the transmembrane pressure difference, and the emulsifier concentration. Stable emulsions with a very narrow droplet size distribution and a mean droplet diameter lower than 0.27 µm were produced using 10 wt % PGPR 90 at a pressure difference below 30 kPa.

  6. A method for producing a water and coal suspension

    Energy Technology Data Exchange (ETDEWEB)

    Mutase, T.; Khongo, T.; Minemura, N.; Nakai, S.; Ogura, K.; Savada, M.

    1983-08-30

    Coal dust (100 parts with a 95 to 99 percent content of particles with a size of 7 to 150 micrometers) is loaded into a mixture of hydrocarbon oil (1 to 20 parts) and water (300 to 1,000 parts) and mixed for 3 to 5 minutes at a rotation frequency of 1,800 to 1,500 per minute. The agglomerates of the coal dust and hydrocarbon (Uv) (100 parts) produced in this manner are then mixed with water (25 to 60 parts), an anion surfacant (PAV) (from 0.1 to 2 parts) which has high dispersion activity and a nonionogenic surfacant (0.1 to 2 parts) which has an HLB indicator of from 7 to 17 (preferably 13) to ensure a high consistency of the aqueous suspension of high quality coal, characterized by high fluidity (dynamic viscosity from 0.5 to 1.4 pascals times seconds). It is preferable to use a heavy oil fraction, kerosene, residue from oil distillation or an anthracite coal resin as the hydrocarbon oil. Separation of the ash from the suspension is increased by adding the surfacants and a water soluble inorganic salt which provides for an alkalinity of the aqueous solution (a pH of 7). It is recommended that a salt of alkylbenzolsulfo acid, a sodium salt of polyoxyethylenalkylphenolsulfo acid, sodium laurylsulfate, ammonium lauryl sulfate polyoxyethylensorbitantristearate, polyoxyethylenlaurylic acid, polyoxyethylennonylphenol ether or polyoxyethyllauric ether be used as the surfacant.

  7. Effects of produced water discharges on the colonization potential of Macrocystis pyrifera spores

    International Nuclear Information System (INIS)

    Lewis, R.J.; Reed, D.C.

    1993-01-01

    Point sources of pollution (e.g. industrial outfalls) may produce ecological impacts at distant locations if pollutants affect dispersive propagules. The authors used laboratory experiments to determine how exposure to produced water (PW; aqueous fraction of petroleum production that is typically discharged into coastal waters) in the water column influences the colonization potential of giant kelp (Macrocystis pyrifera) spores on the bottom. Spores were maintained in suspension in 18 L containers and exposed to one of five concentrations of PW (0 to 10%) for varying amounts of time. Spore swimming generally decreased with increasing PW concentration and exposure duration, with the specific pattern of decrease differing between experimental trials done at different dates. The effect of exposure duration in the water column on the ability of swimming spores to attach to plastic dishes placed the bottom varied with PW concentration. Spores placed in 1 and 10% PW showed a steady decline in their ability to attach with increased exposure; lower concentrations of PW had no such effects. The proportion of spores that germinated after attachment varied tremendously with exposure duration and date of experimental trial. A low proportion of spores that settled during the first 12 h germinated, indicative of a short period of precompetency. Surprisingly, water column exposure to high concentrations of PW during the first 12 h reduced this precompetent period and greatly improved germination success. The magnitude of this enhancement, however, varied among dates. Delayed expression of PW effects were not observed in developing gametophytes; survival of individuals that successfully germinated and gamete production was not affected by previous exposure to PW as a spore

  8. Distribution Channel Intensity among Table Water Producers in Nigeria

    Directory of Open Access Journals (Sweden)

    Joseph Edewor Agbadudu

    2017-09-01

    Full Text Available Planning for and making reasonable decisions regarding reaching the target market with an organization’s product is a critical task on the part of management, which involves a careful evaluation and selection of its channel structure and intensity.This study therefore examines distribution channel intensity among table water producers in Edo State, Nigeria. The focus of the study is to ascertain the variables that significantly predict distribution intensity among the firms in the table water industry in Edo State. The study seeks to proffer answer to fundamental question of why brands within a single category of a given consumer good differ significantly in their distribution intensity. Using a survey research design, the data used for this study were obtained by taking a sample of 110 table water firms within the three senatorial districts in the State. The data obtained were presented and analyzed using different statistical tools such as mean and multiple regression through Statistical Packages for Social Sciences (SPSS version 22 software. Findings revealed that manufacturers’ target focus, manufacturers’ support program, brand quality and level of firm’s technological advancement were significant predictors of distribution channel intensity among the industrial players in table water industry in the State. Based on the findings, the study recommended that table water firms within the State can secure a competitive edge over their fellow counterpart in the industry by designing an optimal distribution intensity that will meet up their marketing objectives. It is also recommended that the adoption of modern technology in form of online sales is an efficient way of sales and distribution which could be used to enhance their distribution techniques if there is a need to cut down on middle men due to increased cost. The study concluded that optimal distribution intensity could be achieved not by mere imitation of competitors but through

  9. Enteric Pathogen Survival Varies Substantially in Irrigation Water from Belgian Lettuce Producers

    Science.gov (United States)

    Van Der Linden, Inge; Cottyn, Bart; Uyttendaele, Mieke; Berkvens, Nick; Vlaemynck, Geertrui; Heyndrickx, Marc; Maes, Martine

    2014-01-01

    It is accepted that irrigation water is a potential carrier of enteric pathogens, such as Salmonella and E. coli O157:H7 and, therefore, a source for contamination of fresh produce. We tested this by comparing irrigation water samples taken from five different greenhouses in Belgium. The water samples were inoculated with four zoonotic strains, two Salmonella and two E. coli O157:H7 strains, and pathogen survival and growth in the water were monitored up till 14 days. The influence of water temperature and chemical water quality was evaluated, and the survival tests were also performed in water samples from which the resident aquatic microbiota had previously been eliminated by filter sterilization. The pathogen’s survival differed greatly in the different irrigation waters. Three water samples contained nutrients to support important growth of the pathogens, and another enabled weaker growth. However, for all, growth was only observed in the samples that did not contain the resident aquatic microbiota. In the original waters with their specific water biota, pathogen levels declined. The same survival tendencies existed in water of 4 °C and 20 °C, although always more expressed at 20 °C. Low water temperatures resulted in longer pathogen survival. Remarkably, the survival capacity of two E. coli 0157:H7 strains differed, while Salmonella Thompson and Salmonella Typhimurium behaved similarly. The pathogens were also transferred to detached lettuce leaves, while suspended in two of the water samples or in a buffer. The effect of the water sample on the pathogen’s fitness was also reproduced on the leaves when stored at 100% relative humidity. Inoculation of the suspension in buffer or in one of the water samples enabled epiphytic growth and survival, while the pathogen level in the other water sample decreased once loaded on the leaves. Our results show that irrigation waters from different origin may have a different capacity to transmit enteric pathogens and

  10. Produção de snacks funcionais à base de farinha de soja e polvilho azedo Production of functional snacks from soybean flour and sour cassava starch

    Directory of Open Access Journals (Sweden)

    Magali Leonel

    2010-06-01

    Full Text Available Este trabalho teve por objetivo avaliar o efeito da temperatura de extrusão e da porcentagem de farinha de soja sobre a expansão (IE, o índice de absorção de água (IAA, o índice de solubilidade em água (ISA, a cor (L*, a* e b* e a dureza de biscoitos extrusados. O processo de extrusão seguiu o delineamento central composto rotacional para dois fatores, totalizando 11 tratamentos. Os resultados obtidos mostraram que a temperatura e a porcentagem de farinha de soja tiveram efeitos significativos sobre as propriedades físicas dos produtos. Nas condições intermediárias de temperatura e baixa porcentagem de farinha de soja (10%, é possível obter biscoitos funcionais de mandioca com elevada expansão, índices intermediários de absorção e solubilidade em água, cor clara e baixa dureza.This study aimed to evaluate the effect of the extrusion temperature and the percentage of soybean flour in mixes on the expansion index (EI, water absorption index (WAI, water solubility index(WSI; color (L *, a *, b * and hardness of extruded sour cassava snacks. The extrusion process followed the rotational central composite design for two factors, totalizing 11 treatments. The results showed that the extrusion temperature and percentage of soybean flour in mixes had significant effects on the physical properties of products. Under the conditions of intermediate temperature and low percentage of soybean meal is possible to obtain function cassava snacks with high expansion, intermediate index of absorption and solubility in water, light color and low hardness.

  11. Overview of Chronic Oral Toxicity Values for Chemicals Present in Hydraulic Fracturing Fluids, Flowback and Produced Waters

    Science.gov (United States)

    as part of EPA's Hydraulic Fracturing Drinking Water Assessment, EPA is summarizing existing toxicity data for chemicals reported to be used in hydraulic fracturing fluids and/or found in flowback or produced waters from hydraulically fractured wells

  12. Temporal characterization and statistical analysis of flowback and produced waters and their potential for reuse.

    Science.gov (United States)

    Oetjen, Karl; Chan, Kevin E; Gulmark, Kristoffer; Christensen, Jan H; Blotevogel, Jens; Borch, Thomas; Spear, John R; Cath, Tzahi Y; Higgins, Christopher P

    2018-04-01

    Hydraulic fracturing (HF) has allowed for the utilization of previously unattainable shale oil and gas (O&G) resources. After HF is complete, the waters used to increase the facies' permeability return uphole as wastewaters. When these waters return to the surface, they are characterized by complex organic and inorganic chemistry, and can pose a health risk if not handled correctly. Therefore, these waters must be treated or disposed of properly. However, the variability of these waters' chemical composition over time is poorly understood and likely limits the applicability of their reuse. This study examines the water chemistry of a hydraulically fractured site in the Niobrara formation throughout the flowback period. Samples were collected every other day for the first 18days, then on a regular basis for three months. We identified HF fluid additives, including benzalkonium chlorides (BACs), alkyl ethoxylates (AEOs), and polyethylene glycols (PEGs), as well as geogenic components present in flowback and produced waters, their overall temporal pattern, and variables affecting the reuse of these waters. Observations indicate that alkalinity and iron may limit the reuse of these waters in HF, while chloride and alkalinity may limit the use of these waters for well-casing cement. The presence of numerous surfactant homologs, including biocides, was also observed, with the highest levels at the beginning of the flowback period. Principal component analysis identified three unique groupings in the chemical data that correspond to different stages in the flowback period: (1) the flowback stage (days 1-2); (2) the transition stage (days 6-21); and (3) the produced water stage (days 21-87). Results from this study will be important when designing decision frameworks for assessing water treatment options, particularly if onsite treatment is attempted. Successful reclamation of these waters may alleviate stress on water resources that continues to negatively impact the U. S

  13. Total petroleum hydrocarbon degradation by hybrid electrobiochemical reactor in oilfield produced water

    International Nuclear Information System (INIS)

    Mousa, Ibrahim E.

    2016-01-01

    The crude oil drilling and extraction operations are aimed to maximize the production may be counterbalanced by the huge production of contaminated produced water (PW). PW is conventionally treated through different physical, chemical, and biological technologies. The efficiency of suggested hybrid electrobiochemical (EBC) methods for the simultaneous removal of total petroleum hydrocarbon (TPH) and sulfate from PW generated by petroleum industry is studied. Also, the factors that affect the stability of PW quality are investigated. The results indicated that the effect of biological treatment is very important to keep control of the electrochemical by-products and more TPH removal in the EBC system. The maximum TPH and sulfate removal efficiency was achieved 75% and 25.3%, respectively when the detention time was about 5.1 min and the energy consumption was 32.6 mA/cm 2 . However, a slight increasing in total bacterial count was observed when the EBC compact unit worked at a flow rate of average 20 L/h. Pseudo steady state was achieved after 30 min of current application in the solution. Also, the results of the study indicate that when the current intensity was increased above optimum level, no significant results occurred due to the release of gases. - Highlights: • The hybrid electrolytic biological cell was used for degradation of oilfield produced water. • Decomposition of Total Petroleum Hydrocarbon with or without the biofilter. • High saline water with the high chloride and sulfate ions content treatment. • The removal of electrochemical by-products is a phase change technique that requires the maintenance the biofilm on the filter media, which is sensitive and a complex operation. • Biofilter is efficient for the degradation of PW bye products, the critical drawback to their utility in full-scale operations is high TDS water content and detention time of treatment.

  14. Microbial water diversion technique-designed for near well treatment in low temperature sandstone reservoirs in the North Sea

    Energy Technology Data Exchange (ETDEWEB)

    Paulsen, J.E.; Vatland, A. [RF-Rogaland Research, Stavanger (Norway); Sorheim, R. [SINTEF, Oslo (Norway)] [and others

    1995-12-31

    A Norwegian Research Program on Improved Oil Recovery (IOR) in North Sea reservoirs was launched in 1992. Microbial methods, applied in this context, is a part of this program. The scope, the methodological approach, and results from the three first years are presented. Water profile control, using biomass to block high permeable zones of a reservoir, has been investigated using nitrate-reducing bacteria in the injected sea water as plugging agents. Emphasis has been put on developing a process that does not have disadvantages secondary to the process itself, such as souring and impairment of the overall injectivity of the field. Data from continuous culture studies indicate that souring may successfully be mitigated by adding nitrite to the injected seawater. The morphology and size of generic-nitrate-reducing seawater bacteria have been investigated. Screening of growth-promoting nutrients has been carried out, and some sources were detected as favorable. Transport and penetration of bacteria in porous media have been given special attention. Investigations with sand packs, core models, and pore micromodels have been carried out. The inherent problems connected with permeability contrasts and flow patterns, versus bacterial behavior, are believed to be critical for the success of this technology. Data from the transport and blocking experiments with the porous matrices confirm this concern. The technology is primarily being developed for temperatures less than 40{degrees}C.

  15. Evaluation of wood chip gasification to produce reburn fuel for coal-fired boilers

    Science.gov (United States)

    Gasification/reburn testing with biomass and other wastes is of interest to both the U.S. Environmental Protection Agency (EPA) and the Italian Ministry of the Environment & Territory (IMET). Gasification systems that use wastes as feedstock should provide a clean, efficient sour...

  16. Effects of seasonal operation on the quality of water produced by public-supply wells.

    Science.gov (United States)

    Bexfield, Laura M; Jurgens, Bryant C

    2014-09-01

    Seasonal variability in groundwater pumping is common in many places, but resulting effects of seasonal pumping stress on the quality of water produced by public-supply wells are not thoroughly understood. Analysis of historical water-quality samples from public-supply wells completed in deep basin-fill aquifers in Modesto, California (134 wells) and Albuquerque, New Mexico (95 wells) indicates that several wells have seasonal variability in concentrations of contaminants of concern. In Modesto, supply wells are more likely to produce younger groundwater with higher nitrate and uranium concentrations during the summer (high) pumping season than during the winter (low) pumping season. In Albuquerque, supply wells are more likely to produce older groundwater with higher arsenic concentrations during the winter pumping season than during the summer pumping season. Seasonal variability in contaminant concentrations in Modesto is influenced primarily by effects of summer pumping on vertical hydraulic gradients that drive migration of shallow groundwater through the aquifer to supply wells. Variability in Albuquerque is influenced primarily by the period of time that a supply well is idle, allowing its wellbore to act as a conduit for vertical groundwater flow and contaminant migration. However, both processes are observed in each study area. Similar findings would appear to be likely in other alluvial basins with stratified water quality and substantial vertical head gradients. Results suggest that even in aquifers dominated by old groundwater, changes to seasonal pumping patterns and/or to depth of well completion can help reduce vulnerability to selected contaminants of either natural or anthropogenic origin. Published 2014. This article is a U.S. Government work and is in the public domain in the USA. Groundwater published by Wiley Periodicals, Inc. on behalf of National Ground Water Association.

  17. Evaluation of the freeze-thaw/evaporation process for the treatment of produced waters. Final report, August 1992--August 1996

    Energy Technology Data Exchange (ETDEWEB)

    Boysen, J.E.; Walker, K.L.; Mefford, J.L.; Kirsch, J.R. [Resource Technology Corp., Laramie, WY (United States); Harju, J.A. [North Dakota Univ., Grand Forks, ND (United States). Energy and Environmental Research Center

    1996-06-01

    The use of freeze-crystallization is becoming increasingly acknowledged as a low-cost, energy-efficient method for purifying contaminated water. The natural freezing process can be coupled with natural evaporative processes to treat oil and gas produced waters year round in regions where subfreezing temperatures seasonally occur. The climates typical of Colorado`s San Juan Basin and eastern slope, as well as the oil and gas producing regions of Wyoming, are well suited for application of these processes in combination. Specifically, the objectives of this research are related to the development of a commercially-economic FTE (freeze-thaw/evaporation) process for the treatment and purification of water produced in conjunction with oil and natural gas. The research required for development of this process consists of three tasks: (1) a literature survey and process modeling and economic analysis; (2) laboratory-scale process evaluation; and (3) field demonstration of the process. Results of research conducted for the completion of these three tasks indicate that produced water treatment and disposal costs for commercial application of the process, would be in the range of $0.20 to $0.30/bbl in the Rocky Mountain region. FTE field demonstration results from northwestern New Mexico during the winter of 1995--96 indicate significant and simultaneous removal of salts, metals, and organics from produced water. Despite the unusually warm winter, process yields demonstrate disposal volume reductions on the order of 80% and confirm the potential for economic production of water suitable for various beneficial uses. The total dissolved solids concentrations of the FTE demonstration streams were 11,600 mg/L (feed), 56,900 mg/L (brine), and 940 mg/L (ice melt).

  18. Decision 99-16: Canadian 88 Energy Corp. application to drill a level 4 critical sour gas well, Lochend Field

    International Nuclear Information System (INIS)

    1999-07-01

    Canadian 88 Energy Corp. applied, pursuant to section 2.020 of the Oil and Gas Conservation Regulations, for a licence to drill a level 4 critical sour gas well to be located at Legal Subdivision 10 of Section 35, Township 26, Range 3, West of the fifth Meridian. The level 4 designation is used to determine the minimum separation distance between the well and land-use surface developments during the suspended or producing stage. This 10-35 well would require a minimum separation distance of 100 m from any individual dwelling development up to eight dwellings per quarter section, 500 m from an unrestricted county development, and 1500 m from an urban centre or public facility. The application and interventions were considered at a hearing in Calgary, Alberta commencing on 4 May 1998. The issues respecting the application were: the need for the well, the proposed well location, the potential hydrogen sulfide release rate, the drilling and completion considerations, the public safety risk assessment, emergency preparedness, the land use impacts, and public consultation. The Board believes that the public safety risks associated with the proposed well are representative of normal industrial risks accepted by society and that the well can be safely drilled. Also, the Board believes that these risks are similar to existing facilities and are acceptable if managed through strict adherence to the risk control measures required in the existing regulations. Given this, and having considered all the evidence, the Board is prepared to issue the well licence after Canadian 88 has undertaken, committed to, and submitted a number of requirements for review

  19. Temporal characterization and statistical analysis of flowback and produced waters and their potential for reuse

    DEFF Research Database (Denmark)

    Oetjen, Karl; Chan, Kevin E; Gulmark, Kristoffer

    2018-01-01

    organic and inorganic chemistry, and can pose a health risk if not handled correctly. Therefore, these waters must be treated or disposed of properly. However, the variability of these waters' chemical composition over time is poorly understood and likely limits the applicability of their reuse......), alkyl ethoxylates (AEOs), and polyethylene glycols (PEGs), as well as geogenic components present in flowback and produced waters, their overall temporal pattern, and variables affecting the reuse of these waters. Observations indicate that alkalinity and iron may limit the reuse of these waters in HF......Hydraulic fracturing (HF) has allowed for the utilization of previously unattainable shale oil and gas (O&G) resources. After HF is complete, the waters used to increase the facies' permeability return uphole as wastewaters. When these waters return to the surface, they are characterized by complex...

  20. Insight into the prevalence and distribution of microbial contamination to evaluate water management in the fresh produce processing industry.

    Science.gov (United States)

    Holvoet, Kevin; Jacxsens, Liesbeth; Sampers, Imca; Uyttendaele, Mieke

    2012-04-01

    This study provided insight into the degree of microbial contamination in the processing chain of prepacked (bagged) lettuce in two Belgian fresh-cut produce processing companies. The pathogens Salmonella and Listeria monocytogenes were not detected. Total psychrotrophic aerobic bacterial counts (TPACs) in water samples, fresh produce, and environmental samples suggested that the TPAC is not a good indicator of overall quality and best manufacturing practices during production and processing. Because of the high TPACs in the harvested lettuce crops, the process water becomes quickly contaminated, and subsequent TPACs do not change much throughout the production process of a batch. The hygiene indicator Escherichia coli was used to assess the water management practices in these two companies in relation to food safety. Practices such as insufficient cleaning and disinfection of washing baths, irregular refilling of the produce wash baths with water of good microbial quality, and the use of high product/water ratios resulted in a rapid increase in E. coli in the processing water, with potential transfer to the end product (fresh-cut lettuce). The washing step in the production of fresh-cut lettuce was identified as a potential pathway for dispersion of microorganisms and introduction of E. coli to the end product via cross-contamination. An intervention step to reduce microbial contamination is needed, particularly when no sanitizers are used as is the case in some European Union countries. Thus, from a food safety point of view proper water management (and its validation) is a critical point in the fresh-cut produce processing industry.

  1. Breckinridge Project, initial effort

    Energy Technology Data Exchange (ETDEWEB)

    None

    1982-01-01

    Report IV, Volume 5, provides descriptions, data, and drawings pertaining to Cryogenic Hydrogen Purification (Plant 8), Sour Water Treating (Plant 9), and the Sulfur Plant (Plant 10). Cryogenic Hydrogen Purification (Plant 8) purifies the purge gas stream from the Gas Plant (Plant 7, described in Report IV, Volume 4) to a 93% purity hydrogen product. Sour Water Treating (Plant 9) removes free ammonia and acid gases from sour water and separates them to recover a high quality anhydrous ammonia product. The Sulfur Plant (Plant 10) recovers, as a saleable liquid product, approximately 95% of the sulfur in feed streams from the Gas Plant (Plant 7, described in Report IV, Volume 4), Sour Water Treating (Plant 9), Gasification and Purification (Plant 12, described in Report IV, Volume 6), and Stack Gas Scrubbing (Plant 35, described in Report V, Volume 3). The following information is included for each of the three plants described in this volume: a description of the plant's process design, including the utility balance, catalysts and chemicals usage, and a process flow diagram; an equipment list, including item numbers and descriptions; data sheets and sketches for major plant components; and pertinent engineering drawings. An appendix contains: an overall site plan showing the locations of all plants; and the symbols and legend for the piping and instrument diagrams included in this volume.

  2. Discharges of produced waters from oil and gas extraction via wastewater treatment plants are sources of disinfection by-products to receiving streams

    Science.gov (United States)

    Hladik, Michelle; Focazio, Michael J.; Engle, Mark

    2014-01-01

    Fluids co-produced with oil and gas production (produced waters) are often brines that contain elevated concentrations of bromide. Bromide is an important precursor of several toxic disinfection by-products (DBPs) and the treatment of produced water may lead to more brominated DBPs. To determine if wastewater treatment plants that accept produced waters discharge greater amounts of brominated DBPs, water samples were collected in Pennsylvania from four sites along a large river including an upstream site, a site below a publicly owned wastewater treatment plant (POTW) outfall (does not accept produced water), a site below an oil and gas commercial wastewater treatment plant (CWT) outfall, and downstream of the POTW and CWT. Of 29 DBPs analyzed, the site at the POTW outfall had the highest number detected (six) ranging in concentration from 0.01 to 0.09 μg L− 1 with a similar mixture of DBPs that have been detected at POTW outfalls elsewhere in the United States. The DBP profile at the CWT outfall was much different, although only two DBPs, dibromochloronitromethane (DBCNM) and chloroform, were detected, DBCNM was found at relatively high concentrations (up to 8.5 μg L− 1). The water at the CWT outfall also had a mixture of inorganic and organic precursors including elevated concentrations of bromide (75 mg L− 1) and other organic DBP precursors (phenol at 15 μg L− 1). To corroborate these DBP results, samples were collected in Pennsylvania from additional POTW and CWT outfalls that accept produced waters. The additional CWT also had high concentrations of DBCNM (3.1 μg L− 1) while the POTWs that accept produced waters had elevated numbers (up to 15) and concentrations of DBPs, especially brominated and iodinated THMs (up to 12 μg L− 1 total THM concentration). Therefore, produced water brines that have been disinfected are potential sources of DBPs along with DBP precursors to streams wherever these wastewaters are discharged.

  3. Tightening water quality regulations produces an innovative separation technology

    International Nuclear Information System (INIS)

    Welther, P.B.; Broussard, P.C.

    1994-01-01

    The impact of the recent proposed changes in the water quality standards for offshore producing platforms is having a far reaching effect on the oil and gas industry. At a time when oil companies are cutting back their work forces and reducing capital outlays in order to stay competitive in the market, water treatment equipment manufacturing companies are aggressively seeking innovative and cost effective solutions to meet the environmental requirements. Necessity drives advancements in technology, so Monosep Corporation has accepted the challenge to improve induced gas flotation technology and to develop enhanced gravity separation. This system of improved gas flotation and enhanced gravity separation can be used to consistently meet the proposed new guideline of an ''oil and grease'' maximum monthly average of 29 mg/l (milligrams per liter) in the discharged water from offshore platforms. The results demonstrated in the field suggest that adding enhanced gravity separation upstream of existing gas flotation units can improve performance sufficient to meet the Proposed stricter discharge limits. For platforms that do not have efficient gas flotation units, the old units can be replaced or modified to include the new features improved gas flotation technology like the Veirsep. For those few platforms are having difficulty meeting the current discharge requirements, both a new improved gas flotation unit, as well as a more sophisticated upstream gravity separator like the Cyclosep, may need to be installed. Chemical additives are sometimes a required necessity, but must be used sparingly due to the potential for creating soluble oil problems

  4. Treatment of the oily produced water (OPW using coagulant mixtures

    Directory of Open Access Journals (Sweden)

    R. Hosny

    2016-09-01

    Full Text Available Treatment of the oily produced water (OPW before injection into oil reservoirs is necessary to reduce formation damage. This can be done using chemo-physical process to minimize the oil droplets in water. In this respect, this work aims to extract natural polymer (chitosan from shrimp shells and mix it with coagulants (chitosan/carboxy methyl cellulose and chitosan/aluminum sulfate to adsorb oil from OPW. Adsorption experiments were carried out in batch mode firstly to choose the best coagulants in water treatment, also to investigate the effects of pH on the adsorption uptake, adsorbent dosage, coagulant mixture doses and contact time. It was found that the oil removal by chitosan reached 96.35% and 59% at pH = 4 and pH = 9, respectively. The ability of chitosan to remove oil was increased after adding different coagulants CMC/or aluminum sulfate at average mixing time between 30 and 60 min. It was also found that the highest removal efficiency of chitosan/CMC is 99% at (90% chitosan: 10% CMC and chitosan/Al2(SO43 is 85% at (80% chitosan: 20% Al2(SO43. The SEM photographs of chitosan, chitosan/CMC and chitosan/Al2(SO43 mixture as oil removal showed that chitosan/Al2(SO43 lies between chitosan alone and chitosan/CMC mixture. Generally chitosan/CMC characterized significantly by its high ability to adsorb petroleum oil and suspended solids from OPW, additionally, reduces the economic cost of water treatment.

  5. Selection of autochthonous sour cherry (Prunus cerasus L. genotypes in Feketić region

    Directory of Open Access Journals (Sweden)

    Radičević Sanja

    2012-01-01

    Full Text Available Autochthonous genotypes of fruit species are very important source of genetic variability and valuable material for breeding work. Fruit Research Institute-Čačak has a long tradition of studying autochthonous genotypes of temperate fruits sporadically spread and preserved in some localities in Serbia. Over 2005-2006, the following properties of nine autochthonous sour cherry genotypes grown in Feketic region were investigated: flowering and ripening time, pomological properties, biochemical composition of fruits and field resistance to causal agents of cherry diseases - cherry leaf spot (Blumeriella jaapii (Rehm. v. Arx., shot-hole (Clasterosporium carpophilum (Lév. Aderh. and brown rot (Monilinia laxa /Ader et Ruhl./ Honey ex Whetz.. The genotypes were tested for the presence of Prune dwarf virus and Prunus necrotic ring spot virus. In majority of genotypes fruits were large, with exceptional organoleptical properties, whereas ripening time was in the first ten or twenty days of June. The highest fruit weight was observed in F-1 genotype (8.1 g. The highest soluble solids and total sugars content were found in F- 4 genotype (17.60% and 14.25%, respectively. As for field resistance to causal agents of diseases and good pomo-technological properties, F-1, F-2, F-3, F-7 and F-8 genotypes were singled out. [Projekat Ministarstva nauke Republike Srbije, br. TR31064

  6. Formation of the Innovation Component of Marketing Technologies of Enterprises That Produce Mineral Waters

    Directory of Open Access Journals (Sweden)

    Golodniuk Olena S.

    2014-03-01

    Full Text Available The article considers main marketing technologies of building competitive advantages by enterprises that produce Ukrainian mineral waters. It considers individual innovations of the conceptual (eco-marketing and applied (branding, benchmarking and competitive reconnaissance nature with consideration of their significance for participants of this market. It offers directions of increasing the innovation component of topical marketing technologies with the aim of implementation of their results into management of competitive advantages of enterprises. It draws a conclusion about a necessity of: reducing evident and growth of a number of latent competitive advantages, based on intellectual technologies, and also development and realisation of a conceptual model of providing marketing innovations in the system of managing competitive advantages of enterprises; and formation of the system of monitoring marketing innovations with the aim of development of additional services and means of building competitive advantages of enterprises that produce mineral waters.

  7. Application of phytoremediation technique in the treatment of produced water using eichornea crassipes

    Energy Technology Data Exchange (ETDEWEB)

    Dune Kingdom, K. [Department of Petroleum Engineering, Rivers State U. of Sc. and Tech., Port Harcourt (Nigeria); Fabian, E. Ezeilo [Department of Civil Engineering, Rivers State U. of Sc. and Tech., Port Harcourt (Nigeria); Longjohn, T. [Department of Petroleum Engineering, Rivers State U. of Sc. and Tech., Port Harcourt (Nigeria)

    2013-07-01

    This paper reports on a study carried out to determine the effectiveness of using a hyper accumulating plant like Eichorneacrassipes (water hyacinth) to reduce toxicity of produced water gotten from an oil field of the Niger Delta region of Nigeria. Results from the phytoremediation experiment showed that the concentration of biological oxygen demand (BOD), chemical oxygen demand (COD), and oil/grease were reduced from initial concentrations of 10.6mg/l, 150 mg/l and 7.70 mg/l to 7.25mg/l, 106.25 mg/l and 8.35mg/l respectively. Heavy metals like iron (Fe), zinc (Zn), Magnesium (Mg), nickel (Ni), copper (Cu), and lead (Pb) were reduced from initial concentrations of 3.00 mg/l, 3.40 mg/l, 1.22 mg/l, 1.40 mg/l, 0.06 mg/l, and 0.030 mg/l to 2.18, 2.09, 0.82, 0.25, 0.015, and 0.009 mg/l, respectively. A comparison of the system’s effluent characteristics with effluent discharge limits in Nigeria, show that for inland, near-shore and offshore disposals, the effluent can be discharged into these environments with minimum public hazards. It is recommended that every company should carryout proper detoxification of produced water before disposal, while regulatory agencies such as DPR, FEPA, etc., must ensure proper monitoring and enforcement of effluent standards.

  8. Treatment of sulphated water of surface origin produced by an open pit coal mine

    Directory of Open Access Journals (Sweden)

    Alan Campos-Sánchez

    2016-12-01

    Full Text Available The purpose of this study was to select the most suitable method of treatment of sulfated water produced by an open pit coal mine in Venezuela. Samples of water taken on surface, middle and bottom of water bodies in three areas were subjected to basic, gravimetric, volumetric and colorimetric analysis. The results indicated that the pH is within limits permitted by current environmental regulations, while total suspended solids, total dissolved solids, and sulfates exceed the normed values. The aerobic wetland method was selected as the most efficient for the removal of sulfates, depending on the physicochemical characteristics of the sulphated waters from the mine and because they are systems that use natural energy to purify water, its construction and maintenance costs Is significantly inferior to the conventional treatments and because, being replicas of natural ecosystems, they are integrated to the environment.

  9. Effect of produced water on feeding and metabolism of Atlantic cod (Gadus morhua)

    Energy Technology Data Exchange (ETDEWEB)

    Volkoff, H.; Parrish, C. [Memorial Univ. of Newfoundland, St. John' s, NL (Canada); Hamoutene, D.; Mabrouk, G.; Samuelson, S.; Mansour, A.; Lee, K. [Fisheries and Oceans Canada, Dartmouth, NS (Canada). Maritimes Region, Ocean Sciences Division

    2007-07-01

    This paper addressed concerns regarding potentially detrimental cumulative effects of waste products from oil industry activities on marine organisms around production sites. The metabolic capacities, feeding and digestive physiology of fish have been shown to change with environmental parameters, which could impact the growth and health status of fish populations. In this study, the effects of produced water (PW) on feeding and metabolism of Atlantic cod was investigated by exposing fish to 0.100 ppm (x 10,000 PW dilution) or 200 ppm (x 500 dilution) of PW for 76 days. Throughout the experiment, food intake and mean weight were monitored. In addition, serum lipids, metabolites and gene expression of a brain appetite regulating factor were measured at the end of the experiment. No significant differences were observed in weight gain or food intake between the 3 groups of fish. Serum metabolites and neuropeptide Y expression remained unchanged between groups. The study is ongoing to complete comparative measurements of whole blood fatty acid profiles in plasma. The preliminary results indicate that feeding and metabolism in cod is not affected by produced water.

  10. A floating water bridge produces water with excess charge

    Science.gov (United States)

    Fuchs, Elmar C.; Sammer, Martina; Wexler, Adam D.; Kuntke, Philipp; Woisetschläger, Jakob

    2016-03-01

    Excess positive and negative Bjerrum-defect like charge (protonic and ‘aterprotonic’, from ancient Greek ἄ'τɛρ, ‘without’) in anolyte and catholyte of high voltage electrolysis of highly pure water was found during the so-called ‘floating water bridge’ experiment. The floating water bridge is a special case of an electrohydrodynamic liquid bridge and constitutes an intriguing phenomenon that occurs when a high potential difference (~kV cm-1) is applied between two beakers of water. To obtain such results impedance spectroscopy was used. This measurement technique allows the depiction and simulation of complex aqueous systems as simple electric circuits. In the present work we show that there is an additional small contribution from the difference in conductivity between anolyte and catholyte which cannot be measured with a conductivity meter, but is clearly visible in an impedance spectrum.

  11. Effects of seasonal operation on the quality of water produced by public-supply wells

    Science.gov (United States)

    Bexfield, Laura M.; Jurgens, Bryant C.

    2014-01-01

    Seasonal variability in groundwater pumping is common in many places, but resulting effects of seasonal pumping stress on the quality of water produced by public-supply wells are not thoroughly understood. Analysis of historical water-quality samples from public-supply wells completed in deep basin-fill aquifers in Modesto, California (134 wells) and Albuquerque, New Mexico (95 wells) indicates that several wells have seasonal variability in concentrations of contaminants of concern. In Modesto, supply wells are more likely to produce younger groundwater with higher nitrate and uranium concentrations during the summer (high) pumping season than during the winter (low) pumping season. In Albuquerque, supply wells are more likely to produce older groundwater with higher arsenic concentrations during the winter pumping season than during the summer pumping season. Seasonal variability in contaminant concentrations in Modesto is influenced primarily by effects of summer pumping on vertical hydraulic gradients that drive migration of shallow groundwater through the aquifer to supply wells. Variability in Albuquerque is influenced primarily by the period of time that a supply well is idle, allowing its wellbore to act as a conduit for vertical groundwater flow and contaminant migration. However, both processes are observed in each study area. Similar findings would appear to be likely in other alluvial basins with stratified water quality and substantial vertical head gradients. Results suggest that even in aquifers dominated by old groundwater, changes to seasonal pumping patterns and/or to depth of well completion can help reduce vulnerability to selected contaminants of either natural or anthropogenic origin.

  12. Findings of a retrospective survey conducted after the Lodgepole sour gas well blowout to determine if the natural occurrence of bovine abortions and fetal anomalies increased

    International Nuclear Information System (INIS)

    Klavano, G.G.; Christian, R.G.

    1992-01-01

    A survey was conducted after the Lodgepole sour gas well blowout of October 1982 to determine if the incident changed the number and type of bovine abortions and abnormal bovine feti submitted to the diagnostic laboratory from the blowout area. The records of the total number of bovine feti submitted were compared between three areas to determine if there was a significant difference between the areas closer to the well site and the larger total area. No changes or trends could be ascribed to the well blowout. 2 refs., 5 tabs

  13. Produção de biscoitos extrusados de polvilho azedo com fibras: efeito de parâmetros operacionais sobre as propriedades físicas Production of snacks from sour cassava starch and fiber: effect of operational parameters on physical properties

    Directory of Open Access Journals (Sweden)

    Karina Fernandes de Camargo

    2008-09-01

    Full Text Available Neste trabalho buscou-se avaliar o efeito de parâmetros operacionais do processo de extrusão no desenvolvimento de biscoitos de polvilho com fibras, utilizando como matérias-primas o polvilho azedo e o farelo de mandioca. O processamento foi realizado em um extrusor mono-rosca, sendo considerados parâmetros variáveis: temperatura na 3ª zona de extrusão, umidade e porcentagem de fibras na mistura. Para analisar o efeito combinado das variáveis independentes nas características tecnológicas dos extrusados, utilizou-se o delineamento 'central composto rotacional' para três fatores. Os resultados obtidos mostraram efeitos significativos da umidade e porcentagem de fibras sobre o volume específico, sendo que a temperatura afetou os índices de solubilidade e absorção de água dos produtos extrusados. Condições de baixa temperatura (65 °C, baixa umidade (12% e baixo teor de fibras (The purpose of this work was to evaluate the effect of operational extrusion parameters on the production of cassava fiber snacks from sour cassava starch and cassava bagasse. Processing was carried out in a single-screw extruder, with temperature in the third extrusion zone, moisture and fiber percentage as independent variables. In order to evaluate the effect of the independent variables on technological characteristics of the snacks, a central composite design with three factors was used. The results showed significant effects of moisture and fiber percentage on specific volume, and extrusion temperature had effects on Water Solubility Index (WSI and Water Absorption Index (WAI. Products with good technological characteristics can be produced at low temperature (65 °C, low fiber (<4% and low moisture (12% conditions.

  14. Ecosystem effects from produced water and potash mine disposal activities

    International Nuclear Information System (INIS)

    Roy, R.; Davis, D.; Hopkins, S.

    1993-01-01

    This study was initiated to determine the chemical, physical, and ecosystem effects of produced water and potash mine disposal practices upon naturally occurring-hypersaline playas in southeast New Mexico, Several playas that receive discharges were compared to several nearby reference playas. Results revealed that the treatment playas had been significantly altered when compared to the reference playas. For example, the salinity of treatment playas were greater than 300 per-thousand and those of reference playas were less than 200 per-thousand. The dominant ions in water and sediments of treatment playas were sodium and chloride. The major ions in reference playa water and sediments were sodium, calcium, chloride, and sulfate. In some instances aromatic hydrocarbon concentrations exceeded 13,000 ng/g in sediments from treatment playas. Aromatic hydrocarbon concentrations were less than 100 ng/g in sediments from reference playas. Surveys revealed that treatment playas supported few, if any, invertebrates. On the other hand, reference playas supported dense populations of brine shrimp Artemis and brine fly Hydropyrus larvae. Surveys also indicated that reference playas were used by shorebirds for nesting and feeding, whereas treatment playas were used as loafing areas by waterfowl. Unfortunately, dead waterfowl were found along the shores of several treatment playas. Necropsies revealed that the most likely cause of death was salt toxicosis

  15. Method to produce water-soluble sugars from biomass using solvents containing lactones

    Science.gov (United States)

    Dumesic, James A.; Luterbacher, Jeremy S.

    2017-08-08

    A process to produce an aqueous solution of carbohydrates that contains C6-sugar-containing oligomers, C6 sugar monomers, C5-sugar-containing oligomers, C5 sugar monomers, or any combination thereof is presented. The process includes the steps of reacting biomass or a biomass-derived reactant with a solvent system including a lactone and water, and an acid catalyst. The reaction yields a product mixture containing water-soluble C6-sugar-containing oligomers, C6-sugar monomers, C5-sugar-containing oligomers, C5-sugar monomers, or any combination thereof. A solute is added to the product mixture to cause partitioning of the product mixture into an aqueous layer containing the carbohydrates and a substantially immiscible organic layer containing the lactone.

  16. A floating water bridge produces water with excess charge

    International Nuclear Information System (INIS)

    Fuchs, Elmar C; Sammer, Martina; Wexler, Adam D; Kuntke, Philipp; Woisetschläger, Jakob

    2016-01-01

    Excess positive and negative Bjerrum-defect like charge (protonic and ‘aterprotonic’, from ancient Greek ατερ, ‘without’) in anolyte and catholyte of high voltage electrolysis of highly pure water was found during the so-called ‘floating water bridge’ experiment. The floating water bridge is a special case of an electrohydrodynamic liquid bridge and constitutes an intriguing phenomenon that occurs when a high potential difference (∼kV cm −1 ) is applied between two beakers of water. To obtain such results impedance spectroscopy was used. This measurement technique allows the depiction and simulation of complex aqueous systems as simple electric circuits. In the present work we show that there is an additional small contribution from the difference in conductivity between anolyte and catholyte which cannot be measured with a conductivity meter, but is clearly visible in an impedance spectrum. (paper)

  17. Changes in physical properties of extruded sour cassava starch and quinoa flour blend snacks Mudanças nas propriedades físicas de snacks extrusados de misturas de polvilho azedo e farinha de quinoa

    Directory of Open Access Journals (Sweden)

    Lívia Giolo Taverna

    2012-12-01

    Full Text Available Given the broad acceptance of sour cassava starch biscuits in Brazil and the nutritional quality of quinoa flour, this study aimed to evaluate the effect of extrusion temperature, screw speed, moisture, and amount of quinoa flour on the physical properties of puffed snacks. Extrusion process was carried out using a single-screw extruder in a factorial central composite design with four factors. Effects of moisture and amount of quinoa flour on the expansion index and specific volume of snacks were observed. There was a pronounced increase in water solubility index of blends with the extrusion process with significant effects of all process parameters on the WSI. Higher water absorption index (WAI was observed under high temperature, low moisture, and lower quinoa flour amount. Temperature and amount of quinoa flour influenced the color of the snacks. A positive quadratic effect of quinoa flour on hardness of products was observed. Blends of sour cassava starch and quinoa flour have good potential for use as raw material in production of extruded snacks with good physical properties.Dada a ampla aceitação do biscoito de polvilho azedo no Brasil e a qualidade nutricional da farinha de quinoa, este trabalho objetivou avaliar o efeito da temperatura de extrusão, rotação da rosca, umidade e porcentagem de farinha de quinoa sobre as propriedades físicas de snacks expandidos. O processo foi realizado em extrusor monorrosca, seguindo o delineamento central composto rotacional para quatro fatores. Foi observado o efeito da umidade e da porcentagem de farinha de quinoa sobre o índice de expansão e volume específico. Houve um aumento pronunciado na solubilidade das misturas com o processo de extrusão, com efeitos significativos de todos os parâmetros de processo no ISA. Maior índice de absorção de água (IAA foi observado em alta temperatura, baixa umidade e menor porcentagem de farinha de quinoa. Temperatura e porcentagem de farinha de

  18. Treatment of produced water using hydrocyclones; Tratamento de agua produzida usando hidrociclone

    Energy Technology Data Exchange (ETDEWEB)

    Freitas, Andrea G.B. de; Paixao, Ana Eleonora A.; Santana, Claudia R.; Silva, Gabriel Francisco da [Universidade Federal de Sergipe (UFS), Aracaju, SE (Brazil). Nucleo de Pos-graduacao em Engenharia Quimica

    2008-07-01

    Beyond a great number of applications in mineral process, the hydrocyclone separation has been used recently in an increasing number of fields, such as: environmental engineering, petrochemical engineering, food engineering, electrochemical engineering, pulp bioengineering, processes and paper industries, among others. Nowadays, the produced water is treated and then reinjected in the surface and also in return to the formation. In the offshore platforms, the produced water can be directly discarded in the ocean, since the dispersed phase concentration (oil) is according to Brazilian regulating agency limits. The basic principle used in hydrocyclone separation is the centrifugal sedimentation machine: the suspended particles are submitted to centrifugal acceleration, which separates them from the fluid. The basic geometry of a hydrocyclone consists of four parts: a cylindrical section for feeding, a conical section for swirling, an overflow and an under flow. The project depends on the fluid properties and the quality of the effluent. Hydrocyclones have become more interesting for some industries due to its innumerable advantages, such as: simple structure, low cost, high capacity and small volume. The theoretical study of draining in hydrocyclone is done using conservation mass and moment equations, which are non linear partial equations, with a difficulty in analytical resolution. (author)

  19. Process for purification of waste water produced by a Kraft process pulp and paper mill

    Science.gov (United States)

    Humphrey, M. F. (Inventor)

    1979-01-01

    The water from paper and pulp wastes obtained from a mill using the Kraft process is purified by precipitating lignins and lignin derivatives from the waste stream with quaternary ammonium compounds, removing other impurities by activated carbon produced from the cellulosic components of the water, and then separating the water from the precipitate and solids. The activated carbon also acts as an aid to the separation of the water and solids. If recovery of lignins is also desired, then the precipitate containing the lignins and quaternary ammonium compounds is dissolved in methanol. Upon acidification, the lignin is precipitated from the solution. The methanol and quaternary ammonium compound are recovered for reuse from the remainder.

  20. Turbidity and oil removal from oilfield produced water, middle oil company by electrocoagulation technique

    Directory of Open Access Journals (Sweden)

    Mohammed Thamer

    2018-01-01

    Full Text Available Huge quantity of produced water is salty water trapped in the oil wells rock and brought up along with oil or gas during production. It usually contains hydrocarbons as oil and suspended solids or turbidity. Therefore the aim of this study is to treat produced water before being discharge to surface water or re injected in oil wells. In this paper experimental results were investigated on treating produced water (which is obtained from Middle Oil Company-Iraq, through electrocoagulation (EC. The performance of EC was investigated for reduction of turbidity and oil content up to allowable limit. Effect of different parameters were studied; (pH, current density, distance between two electrodes, and electrolysis time. The experimental runs carried out by an electrocoagulation unit was assembled and installed in the lab and the reactor was made of a material Perspex, with a capacity of approximately 2.5 liters and dimensions were 20 cm in length, 14 cm in width and 16 cm height. The electrodes employed were made of commercial materials. The anode was a perforated aluminum rectangular plate with a thickness of 1.72 mm, a height of 60 mm and length of 140 mm and the cathode was a mesh iron. The current was used in the unit with different densities to test the turbidity removing efficiency (0.0025, 0.00633, 0.01266 and 0.0253 A/cm2.The experiment showed that the best turbidity removing was (10, 9.7, 9.2, 18 NTU respectively. The distance between the electrodes of the unit was 3cm. The present turbidity removing was 92.33%. A slight improvement of turbidity removing was shown when the distance between the electrodes was changed from 0.5 to 3 cm with fixation of current density. The best turbidity removing was 93.5% , (7.79 NTU when the distance between the electrodes were 1 cm. The experimental results found that concentration of oil had decreased to (10.7, 11.2, 11.7, 12.3 mg/l when different current densities (0.00253, 0.00633, 0.01266, 0.0253 A/cm2

  1. Microbial quality of irrigation water used in leafy green production in Southern Brazil and its relationship with produce safety.

    Science.gov (United States)

    Decol, Luana Tombini; Casarin, Letícia Sopeña; Hessel, Claudia Titze; Batista, Ana Carolina Fösch; Allende, Ana; Tondo, Eduardo César

    2017-08-01

    Irrigation water has been recognized as an important microbial risk factor for fruits and vegetables in many production areas, but there is still a lack of information about how the microbiological quality of different irrigation water sources and climatic conditions influence the safety of vegetables produced in Brazil. This study evaluated the distribution of generic E. coli and the prevalence of E. coli O157:H7 in two different water sources (ponds and streams bordering farmlands and urban areas) used for irrigation and on commercially produced lettuces in Southern Brazil. We also evaluated the effect of agricultural factors and meteorological conditions in the potential contamination of water and produce samples. A longitudinal study was conducted on four farms during a year (July 2014 to August 2015). The results showed generic E. coli prevalence of 84.8% and 38.3% in irrigation water samples and on lettuces, respectively, indicating irrigation water as an important source of contamination of lettuces. No significant differences were detected in the counts of E. coli between the two different surface water sources. The climatic conditions, particularly rainfall and environmental temperature, have influenced the high concentration of E. coli. The highest loads of E. coli in irrigation water and on lettuces were found during the warmest time of the year. E. coli O157:H7 was detected by qualitative polymerase chain reaction (qPCR) in 13 water samples but only 4 were confirmed by isolation in culture media. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. TEXTURAL, FLOW AND SENSORY PROPERTIES OF FIVE “FRUZELINA” WITH SOUR CHERRIES

    Directory of Open Access Journals (Sweden)

    Irena Bojdo Tomasiak

    2010-05-01

    Full Text Available Gel with sour cherries called “Fruzelina” is a new product in the Polish market widely used in food industry as a decorative element or filling for pastries, as an ingredient in fruit desserts, as an additive to ice creams, whipped cream and waffles. The cherry gels are the product prepared using different types of chemically modified starches. Starch is an additive used to ensure rich and short texture and high viscosity of “Fruzelina”. Food texture and viscosity may be measured by senses and instrumentally. Because of fact that sensory analysis is time consuming and very costly, it is easier and cheaper to determine food properties, especially their texture and flow behaviour by appropriate mechanical tests. The aim of this work was to study the rheological behavior of five cherry gels and evaluate the correlation between textural, flow and sensory properties of these gels measured instrumentally and by human senses. The back extrusion test has been found to be applicable to study the textural properties of cherry gels. There was high positive correlation between gel texture measured by senses and texture parameters measured in back extrusion test. Similar high correlation was identified for consistency coefficient K obtained in Ostwald de Waele model and gel texture assessed by sensory panel. It was found that values of sensory parameters such as taste and odour decreased as the rheological parameters increased. High negative correlations were observed in these cases. Therefore, instrumental measurements can be alternative for more expensive sensory methods. doi:10.5219/53

  3. Characterization of sour cherry isolates of plum pox virus from the Volga Basin in Russia reveals a new cherry strain of the virus.

    Science.gov (United States)

    Glasa, Miroslav; Prikhodko, Yuri; Predajňa, Lukáš; Nagyová, Alžbeta; Shneyder, Yuri; Zhivaeva, Tatiana; Subr, Zdeno; Cambra, Mariano; Candresse, Thierry

    2013-09-01

    Plum pox virus (PPV) is the causal agent of sharka, the most detrimental virus disease of stone fruit trees worldwide. PPV isolates have been assigned into seven distinct strains, of which PPV-C regroups the genetically distinct isolates detected in several European countries on cherry hosts. Here, three complete and several partial genomic sequences of PPV isolates from sour cherry trees in the Volga River basin of Russia have been determined. The comparison of complete genome sequences has shown that the nucleotide identity values with other PPV isolates reached only 77.5 to 83.5%. Phylogenetic analyses clearly assigned the RU-17sc, RU-18sc, and RU-30sc isolates from cherry to a distinct cluster, most closely related to PPV-C and, to a lesser extent, PPV-W. Based on their natural infection of sour cherry trees and genomic characterization, the PPV isolates reported here represent a new strain of PPV, for which the name PPV-CR (Cherry Russia) is proposed. The unique amino acids conserved among PPV-CR and PPV-C cherry-infecting isolates (75 in total) are mostly distributed within the central part of P1, NIa, and the N terminus of the coat protein (CP), making them potential candidates for genetic determinants of the ability to infect cherry species or of adaptation to these hosts. The variability observed within 14 PPV-CR isolates analyzed in this study (0 to 2.6% nucleotide divergence in partial CP sequences) and the identification of these isolates in different localities and cultivation conditions suggest the efficient establishment and competitiveness of the PPV-CR in the environment. A specific primer pair has been developed, allowing the specific reverse-transcription polymerase chain reaction detection of PPV-CR isolates.

  4. Microstructure and Textural Properties of Yoghurts Produced by Exopolysaccharides- Producing Starter Cultures

    DEFF Research Database (Denmark)

    Zhang, Lanjun

    conferred a ropy texture and resulted in yoghurts with decreased water holding capacity and an open microstructure. In addition, one of the LB strains with high amounts of EPS producing capacity improved water retention, when it was combined with an ST strain that produced negligible amounts of EPS...

  5. Fishing for isotopes in the Brookhaven Lab Isotope Producer (BLIP) cooling water

    Energy Technology Data Exchange (ETDEWEB)

    Fitzsimmons, Jonathan [Brookhaven National Lab. (BNL), Upton, NY (United States). Collider Accelerator Dept.

    2016-04-29

    Be-7 has been used in environmental studies; the isotope is produced during BLIP irradiations and accumulates in the 320 gallons of cooling water. Be-7 has a 53.24 day half-life, so the optimal production/purification time is at the end of the BLIP run season. To purify Be-7 fifteen to twenty gallons of BLIP cooling water are removed and pumped through ion exchange columns that retain Be-7. This labor intensive approach captures ~15 mCi of Be-7, but the solution requires further purification. The method can lead to increased radiation exposure to staff. The ideal way to capture isotopes from large volumes is to reach in to the solution and selectively pull out the desired isotope. It is a lot like fishing.

  6. Heavy metal removal from produced water using retorted shale; Remocao de metais pesados em aguas produzidas utilizando xisto retortado

    Energy Technology Data Exchange (ETDEWEB)

    Pimentel, Patricia M.; Melo, Marcos A.F.; Melo, Dulce M.A.; Silva Junior, Carlos N.; Assuncao, Ary L.C. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Anjos, Marcelino J. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia

    2004-07-01

    The Production of oil and gas is usually accompanied by the production of large volume of water that can have significant environmental effects if not properly treated. In this work, the use of retort shale was investigated as adsorbent agent to remove heavy metals in produced water. Batch adsorption studies in synthetic solution were performed for several metal ions. The efficiency removal was controlled by solution pH, adsorbent dosage, and initial ion concentration and agitation times. Two simple kinetic models were used, pseudo-first- and second-order, were tested to investigate the adsorption mechanisms. The equilibrium data fitted well with Langmuir and Freundlich models. The produced water samples were treated by retorted shale under optimum adsorption conditions. Synchrotron radiation total reflection X-ray fluorescence was used to analyze the elements present in produced water samples from oil field in Rio Grande do Norte, Brazil. The removal was found to be approximately 20-50% for Co, Ni, Sr and above 80% for Cr, Ba, Hg and Pb. (author)

  7. Ability of sea-water bacterial consortium to produce electricity and denitrify water

    Science.gov (United States)

    Maruvada, Nagasamrat V. V.; Tommasi, Tonia; Kaza, Kesava Rao; Ruggeri, Bernardo

    Sea is a store house for varied types of microbes with an ability to reduce and oxidize substances like iron, sulphur, carbon dioxide, etc. Most of these processes happen in the sea water environment, but can be applied for purification of wastewater. In the present paper, we discuss the use of a consortium of seawater bacteria in a fuel cell to produce electricity by oxidizing organic matter and reducing nitrates. We also discuss how the growth of the bacterial consortium can lead to an increased electricity production and decreased diffusional resistance in the cell. The analysis was done using electrochemical impedance spectroscopy (EIS), and linear sweep voltammetry (LSV). Here, we use bicarbonate buffered solution, which is the natural buffering agent found in sea. We show that the seawater bacterial consortium can be used in both the anode and cathode parts of the cell. The results confirm the adaptability of the seawater bacteria to different environments and can be used for various applications. Heritage, Erasmus Mundus Programme, European Commission.

  8. Modernized approach for the remediation of produced water impacted sites

    Energy Technology Data Exchange (ETDEWEB)

    Knafla, A.; Carey, J. [Equilibrium Environmental Inc., Calgary, AB (Canada); Stokes, D. [Talisman Energy Inc., Calgary, AB (Canada); Carey, J.; Sunita, R.

    2007-10-01

    This article described a project conducted to remediate a site in southeast Saskatchewan polluted by releases of produced water-related salts and boron during the 1960s. A risk assessment was conducted to define endpoints based on equivalent land capability and the potential for health risks. Multiple toxic stressors complicated the assessment, and limited published data were available regarding cumulative and interactive effects. Boron concentrations exceeded recommended guidelines, and the poor permeability of surface soils caused reduced infiltration and increased run-off. An automated pumping system was designed to allow for variable leachate removal rates depending on groundwater elevations. A distillation system using moderately saline water from a nearby source was designed to offset scaling that occurred due to high calcium sulfate concentrations. Results of the project suggested that the combination of groundwater control, improving surface soil permeability, establishing plant growth, and available water for infiltration resulted in significant improvements in soil quality and an approach towards land capability endpoints. The use of moderately saline irrigation water led to significant improvements in the soil salinity of heavily impacted areas. Test plots were then formed to test the efficacy of manure and calcium nitrate as a remediation technique. Test plots were treated with Roundup, and calcium nitrate before seeding, or with manure and calcium nitrate followed by rototilling and seeding. In treated plots, plant growth was observed for barley, alkali grass, wheatgrasses, orchard grass, rye, and alfalfa. Greater plant height and yield was visible in the manure and calcium nitrate treated plots. A decrease in boron topsoil concentrations was also observed. Average bioconcentration factors was calculated as 29.5. It was concluded that the method can provide a 20 per cent annual soil concentration reduction rate. 6 figs.

  9. A hybrid HTGR system producing electricity, hydrogen and such other products as water demanded in the Middle East

    Energy Technology Data Exchange (ETDEWEB)

    Yan, X., E-mail: yan.xing@jaea.go.jp; Noguchi, H.; Sato, H.; Tachibana, Y.; Kunitomi, K.; Hino, R.

    2014-05-01

    Alternative energy products are being considered by the Middle East countries for both consumption and export. Electricity, water, and hydrogen produced not from oil and gas are amongst those desirable. A hybrid nuclear production system, GTHTR300C, under development in JAEA can achieve this regional strategic goal. The system is based on a 600 MWt HTGR and equipped to cogenerate electricity by gas turbine and seawater desalination by using only the nuclear plant waste heat. Hydrogen is produced via a thermochemical water-splitting process driven by the reactor's 950 °C heat. Additionally process steam may be produced for industrial uses. An example is shown of manufacturing soda ash, an internationally traded commodity, from using the steam produced and the brine discharged from desalination. The nuclear reactor satisfies nearly all energy requirements for the hybrid generations without emitting CO{sub 2}. The passive safety of the reactor as described in the paper permits proximity of siting the reactor with the production facilities to enhance energy transmission. Production flowsheet of the GTHTR300C is given for up to 300 MWe electricity, 58 t/day hydrogen, 56,000 m{sup 3}/day potable water, 3500 t/day steam, and 1000 t/day soda ash. The production thermal efficiency reaches 88%.

  10. MODIFIED REVERSE OSMOSIS SYSTEM FOR TREATMENT OF PRODUCED WATERS

    Energy Technology Data Exchange (ETDEWEB)

    T.M. Whitworth; Liangxiong Li

    2002-09-15

    This report describes work performed during the first year of the project ''Modified Reverse Osmosis System for Treatment of Produced Waters.'' This research project has two objectives. The first objective is to test the use of clay membranes in the treatment of produced waters by reverse osmosis. The second objective is to test the ability of a system patented by the New Mexico Tech Research Foundation to remove salts from reverse osmosis waste streams as a solid. We performed 12 experiments using clay membranes in cross-flow experimental cells. We found that, due to dispersion in the porous frit used adjacent to the membrane, the concentration polarization layer seems to be completely (or nearly completely) destroyed at low flow rates. This observation suggests that clay membranes used with porous frit material many reach optimum rejection rates at lower pumping rates than required for use with synthetic membranes. The solute rejection efficiency decreases with increasing solution concentration. For the membranes and experiments reported here, the rejection efficiency ranged from 71% with 0.01 M NaCl solution down to 12% with 2.3 M NaCl solution. More compacted clay membranes will have higher rejection capabilities. The clay membranes used in our experiments were relatively thick (approximately 0.5 mm). The active layer of most synthetic membranes is only 0.04 {micro}m (0.00004 mm), approximately 1250 times thinner than the clay membranes used in these experiments. Yet clay membranes as thin as 12 {micro}m have been constructed (Fritz and Eady, 1985). Since Darcy's law states that the flow through a material of constant permeability is inversely proportional to it's the material's thickness, then, based on these experimental observations, a very thin clay membrane would be expected to have much higher flow rates than the ones used in these experiments. Future experiments will focus on testing very thin clay membranes. The

  11. Long Term Field Development of a Surfactant Modified Zeolite/Vapor Phase Bioreactor System for Treatment of Produced Waters for Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Lynn Katz; Kerry Kinney; Robert Bowman; Enid Sullivan; Soondong Kwon; Elaine Darby; Li-Jung Chen; Craig Altare

    2007-12-31

    The main goal of this research was to investigate the feasibility of using a combined physicochemical/biological treatment system to remove the organic constituents present in saline produced water. In order to meet this objective, a physical/chemical adsorption process was developed and two separate biological treatment techniques were investigated. Two previous research projects focused on the development of the surfactant modified zeolite adsorption process (DE-AC26-99BC15221) and development of a vapor phase biofilter (VPB) to treat the regeneration off-gas from the surfactant modified zeolite (SMZ) adsorption system (DE-FC26-02NT15461). In this research, the SMZ/VPB was modified to more effectively attenuate peak loads and to maintain stable biodegradation of the BTEX constituents from the produced water. Specifically, a load equalization system was incorporated into the regeneration flow stream. In addition, a membrane bioreactor (MBR) system was tested for its ability to simultaneously remove the aromatic hydrocarbon and carboxylate components from produced water. The specific objectives related to these efforts included the following: (1) Optimize the performance VPBs treating the transient loading expected during SMZ regeneration: (a) Evaluate the impact of biofilter operating parameters on process performance under stable operating conditions. (b) Investigate how transient loads affect biofilter performance, and identify an appropriate technology to improve biological treatment performance during the transient regeneration period of an SMZ adsorption system. (c) Examine the merits of a load equalization technology to attenuate peak VOC loads prior to a VPB system. (d) Evaluate the capability of an SMZ/VPB to remove BTEX from produced water in a field trial. (2) Investigate the feasibility of MBR treatment of produced water: (a) Evaluate the biodegradation of carboxylates and BTEX constituents from synthetic produced water in a laboratory-scale MBR. (b

  12. Surface disposal of produced waters in western and southwestern Pennsylvania: potential for accumulation of alkali-earth elements in sediments

    Science.gov (United States)

    Skalak, Katherine J.; Engle, Mark A.; Rowan, Elisabeth L.; Jolly, Glenn D.; Conko, Kathryn M.; Benthem, Adam J.; Kraemer, Thomas F.

    2014-01-01

    Waters co-produced with hydrocarbons in the Appalachian Basin are of notably poor quality (concentrations of total dissolved solids (TDS) and total radium up to and exceeding 300,000 mg/L and 10,000 pCi/L, respectively). Since 2008, a rapid increase in Marcellus Shale gas production has led to a commensurate rise in associated wastewater while generation of produced water from conventional oil and gas activities has continued. In this study, we assess whether disposal practices from treatment of produced waters from both shale gas and conventional operations in Pennsylvania could result in the accumulation of associated alkali earth elements. The results from our 5 study sites indicate that there was no increase in concentrations of total Ra (Ra-226) and extractable Ba, Ca, Na, or Sr in fluvial sediments downstream of the discharge outfalls (p > 0.05) of publicly owned treatment works (POTWs) and centralized waste treatment facilities (CWTs). However, the use of road spreading of brines from conventional oil and gas wells for deicing resulted in accumulation of Ra-226 (1.2 ×), and extractable Sr (3.0 ×), Ca (5.3 ×), and Na (6.2 ×) in soil and sediment proximal to roads (p < 0.05). Although this study is an important initial assessment of the impacts of these disposal practices, more work is needed to consider the environmental consequences of produced waters management.

  13. a Real-Time GIS Platform for High Sour Gas Leakage Simulation, Evaluation and Visualization

    Science.gov (United States)

    Li, M.; Liu, H.; Yang, C.

    2015-07-01

    The development of high-sulfur gas fields, also known as sour gas field, is faced with a series of safety control and emergency management problems. The GIS-based emergency response system is placed high expectations under the consideration of high pressure, high content, complex terrain and highly density population in Sichuan Basin, southwest China. The most researches on high hydrogen sulphide gas dispersion simulation and evaluation are used for environmental impact assessment (EIA) or emergency preparedness planning. This paper introduces a real-time GIS platform for high-sulfur gas emergency response. Combining with real-time data from the leak detection systems and the meteorological monitoring stations, GIS platform provides the functions of simulating, evaluating and displaying of the different spatial-temporal toxic gas distribution patterns and evaluation results. This paper firstly proposes the architecture of Emergency Response/Management System, secondly explains EPA's Gaussian dispersion model CALPUFF simulation workflow under high complex terrain and real-time data, thirdly explains the emergency workflow and spatial analysis functions of computing the accident influencing areas, population and the optimal evacuation routes. Finally, a well blow scenarios is used for verify the system. The study shows that GIS platform which integrates the real-time data and CALPUFF models will be one of the essential operational platforms for high-sulfur gas fields emergency management.

  14. The Challenge of Producing and Marketing Colloidal Silver Water Filters in Nepal

    Directory of Open Access Journals (Sweden)

    Anne Bogler

    2015-07-01

    Full Text Available Background: Obtaining safe drinking water can be a challenge in Nepal. By training potters and setting up production sites for Colloidal Silver Filters, several non-governmental organizations have tried to provide local people with a low-cost option for household water treatment. Out of 19 trained entrepreneurs, only four are currently producing filters. The goal of this evaluation was to find out what conditions lead to the successful continuation of the production and the reasons for failure. Methods: The evaluation of the potters was based on a Qualitative Comparative Analysis and the conditions looked at were: “Production”, “Collaboration”, “Market” and “Potter”. Results: Analysis showed that production problems and insufficient demand led to the termination of ceramic filter production and that both trouble-free production and high demand are necessary for a sustainable business.

  15. An assessment of whole effluent toxicity testing as a means of regulating waters produced by the oil and gas industry

    International Nuclear Information System (INIS)

    Hill, S.L.; Bergman, H.L.

    1993-01-01

    Approximately 500 million barrels of produced water are discharged to Wyoming's surface waters by the oil and gas industry. This discharges are of two types: direct and indirect. The direct discharges have been issued NPDES permits requiring whole effluent toxicity testing. Toxicity testing requirements have not been incorporated into permits written for indirect discharges because of the applicability of toxicity testing for regulating these waters has not been determined. Preliminary testing has shown that most produced waters are toxic at the point of discharge because of high concentrations of hydrogen sulfide, but that the toxicity of an indirect discharge is often lost before it reaches a receiving stream. Thus, whole effluent toxicity testing of an indirect discharge may be overly stringent, resulting in treatment or reinjection of the water or closure of the well. Any of these options would have severe economic consequences for oil producers and the state's agricultural industry. The purpose of this study was to determine whether whole effluent toxicity testing actually predicts the in-stream effects of indirect discharges on water quality and benthic invertebrate populations. The authors will report the results of short-term ambient toxicity tests and in-stream bioassessments performed upstream and downstream of six indirect discharges located in four drainages in Wyoming

  16. Produced water treatment using polymeric resins; Resinas polimericas para tratamento da agua produzida

    Energy Technology Data Exchange (ETDEWEB)

    Louvisse, Ana Maria Travalloni; Freire, Norma de Oliveira [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas; Queiros, Yure Gomes de Carvalho; Silva, Carla Michele Frota da; Barros, Cintia Chagas; Lucas, Elizabeth Fernandes [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Inst. de Macromoleculas

    2008-07-01

    The treatment and disposal of oily waters from oil production and refining processes represent an important technological pass for attendance of the ambient legislation and to the politics of the Cia of search of the environmental excellence. The reuse or reinjection of the co-produced water has been considered an interesting strategical alternative, however, the water quality requirement for these processes demands a pretreatment step, considering the exit effluent from primary and secondary treatment processes currently used. This work presents resulted of the polymeric resin development for tertiary treatment of oily waters with low oil and grasses content and fine solids, including the dissolved fraction. These resins can adsorb, in reversible form, organic components. Its high adsorption capacity is determined by the polarity, superficial area, range of porosity and a wide distribution of particle size and pore. Another important characteristic is the possibility of its use in some cycles of work due to its weak forces of interaction between the contaminants and the surface of the resin. Regeneration can be carried through of diverse forms, including the use of solvent, with or without the variation of temperature and/or pH. The gotten results indicated a high resin adsorption capacity, with concentrated oily water treatment volume 10,000 times the volume of resin used. (author)

  17. Plant-wide Control for Better De-oiling of Produced Water in Offshore Oil & Gas Production

    DEFF Research Database (Denmark)

    Yang, Zhenyu; Stigkær, Jens Peter; Løhndorf, Bo

    2013-01-01

    This paper discusses the application of plant-wide control philosophy to enhance the performance and capacity of the Produced Water Treatment (PWT) in offshore oil & gas production processes. Different from most existing facility- or material-based PWT innovation methods, the objective of this work...

  18. Potential of hot water extraction of birch wood to produce high-purity dissolving pulp after alkaline pulping.

    Science.gov (United States)

    Borrega, Marc; Tolonen, Lasse K; Bardot, Fanny; Testova, Lidia; Sixta, Herbert

    2013-05-01

    The potential of hot water extraction of birch wood to produce highly purified dissolving pulp in a subsequent soda-anthraquinone pulping process was evaluated. After intermediate extraction intensities, pulps with low xylan content (3-5%) and high cellulose yield were successfully produced. Increasing extraction intensity further decreased the xylan content in pulp. However, below a xylan content of 3%, the cellulose yield dramatically decreased. This is believed to be due to cleavage of glycosidic bonds in cellulose during severe hot water extractions, followed by peeling reactions during alkaline pulping. Addition of sodium borohydride as well as increased anthraquinone concentration in the pulping liquor increased the cellulose yield, but had no clear effects on pulp purity and viscosity. The low intrinsic viscosity of pulps produced after severe extraction intensities and soda-anthraquinone pulping corresponded to the viscosity at the leveling-off degree of polymerization, suggesting that nearly all amorphous cellulose had been degraded. Copyright © 2012 Elsevier Ltd. All rights reserved.

  19. Toxicity identification evaluations of produced-water effluents

    International Nuclear Information System (INIS)

    Sauer, T.C.; Costa, H.J.; Brown, J.S.; Ward, T.J.

    1997-01-01

    Toxicity identification evaluations (TIEs) were performed on 14 produced-water (PW) samples of various salinities from inland and offshore oil- and gas-production facilities operated by different companies in Wyoming, Texas, California, and Louisiana (USA) to evaluate the efficacy of TIE procedures in determining potential toxicants in PW effluents. The research involved acute (24- and 48-h) freshwater and marine toxicity tests on whole PW and PW fractions generated by standard US Environmental Protection Agency and PW-specific fractionation schemes. Factors influencing PW TIEs were investigated, such as the effect of salinity in selecting fractionation manipulations, the effect of toxicity test replication (i.e., reproducibility) in distinguishing changes in toxicities between whole PW and its fractions, and the suitability of different test species in PW TIEs. The results obtained and lessons learned from conducting these PW TIEs are presented in this article. Components, or fractions, contributing to toxicity differed for each PW with no specific fraction being consistently toxic. For most PW samples, toxicity attributed to any one fraction represented only part of the toxicity of the whole sample. However, no more than two fraction types were identified as potential toxicants in any sample. Potential toxicants identified during this study, besides salinity, included acidic and basic organic compound class fractions, particulates removed by filtration at pH 11, ammonia, hydrocarbons, hydrogen sulfide, material removed by pH change, and volatile compounds

  20. New generation of Sour Service Drill Pipe allows addressing highly sour field challenges

    Directory of Open Access Journals (Sweden)

    Thomazic A.

    2013-11-01

    Full Text Available Drill pipes are commonly produced by assembling pipe and tool joints through friction welding. The weld, as a result of this process, presents some challenges for preserving corrosion resistance due to some metallurgical factors such as heterogeneous microstructure, different chemical compositions between the tool joint and the pipe body and heterogeneous mechanical properties close to the welded line. Hence a new drill pipe configuration have been developed including modified chemical composition and modified manufacturing process. These modifications allow for the improvement of mechanical properties performance and corrosion resistance in the welded zone.

  1. Combination gas producing and waste-water disposal well

    Science.gov (United States)

    Malinchak, Raymond M.

    1984-01-01

    The present invention is directed to a waste-water disposal system for use in a gas recovery well penetrating a subterranean water-containing and methane gas-bearing coal formation. A cased bore hole penetrates the coal formation and extends downwardly therefrom into a further earth formation which has sufficient permeability to absorb the waste water entering the borehole from the coal formation. Pump means are disposed in the casing below the coal formation for pumping the water through a main conduit towards the water-absorbing earth formation. A barrier or water plug is disposed about the main conduit to prevent water flow through the casing except for through the main conduit. Bypass conduits disposed above the barrier communicate with the main conduit to provide an unpumped flow of water to the water-absorbing earth formation. One-way valves are in the main conduit and in the bypass conduits to provide flow of water therethrough only in the direction towards the water-absorbing earth formation.

  2. The Use of Water Vapor for Detecting Environments that Lead to Convectively Produced Heavy Precipitation and Flash Floods

    Science.gov (United States)

    Scofield, Rod; Vicente, Gilberto; Hodges, Mike

    2000-01-01

    This Tech Report summarizes years of study and experiences on using GOES Water vapor (6.7 micron and precipitable water) and Special Sensor Microwave Imager (SSM/1) from the Defense Meteorological Satellite Program (DMSP) derived Precipitable Water (PNAI) for detecting environments favorable for convectively produced flash floods. An emphasis is on the moisture. upper air flow, and equivalent potential temperature (Theta(sub e)) patterns that lead to devastating flood events. The 15 minute 6.7 micron water vapor imagery is essential for tracking middle to upper tropospheric disturbances that produce upward vertical motion and initiate flash flood producing systems. Water vapor imagery at 6.7 micron is also used to detect surges of upper level moisture (called tropical water vapor plumes) that have been associated with extremely heavy rainfall. Since the water vapor readily depicts lifting mechanisms and upper level moisture, water vapor imagery is often an excellent source of data for recognizing patterns of heavy precipitation and flash floods. In order to analyze the depth of the moisture, the PW aspects of the troposphere must be measured. The collocation (or nearby location) of high values ofP\\V and instability are antecedent conditions prior to the flash flood or heavy rainfall events. Knowledge of PW magnitudes have been used as thresholds for impending flash flood events, PW trends are essential in flash flood prediction. Conceptual models and water vapor products are used to study some of the characteristics of convective systems that occurred over the United States of America (USA) during the summer of 1997 and the 1997-1998 El Nino. P\\V plumes were associated with most of the \\vest coast heavy precipitation events examined during the winter season of 1997 - 1998, In another study, conducted during the summer season of 1997. results showed that the collocation of water vapor (6.7 micron) and P\\N' plumes possessed higher correlations with predicted

  3. Isotope and chemical investigation of geothermal springs and thermal water produced by oil wells in potwat area, Pakistan

    International Nuclear Information System (INIS)

    Ahmad, M.; Rafique, M.; Tariq, J.A; Choudhry, M.A.; Hussain, Q.M.

    2008-10-01

    Isotopes and geochemical techniques were applied to investigate the origin, subsurface history and reservoir temperatures of geothermal springs in Potwar. Two sets of water samples were collected. Surface temperatures of geothermal springs ranges from 52 to 68.3 C. Waters produced by oil wells in Potwar area were also investigated. Geothermal springs of Potwar area are Na-HCO/sub 3/ type, while the waters produced by oil wells are Na-Cl and Ca-Cl types. Source of both the categories of water is meteoric water recharged from the outcrops of the formations in the Himalayan foothills. These waters undergo very high /sup 18/O-shift (up to 18%) due to rock-water interaction at higher temperatures. High salinity of the oil field waters is due to dissolution of marine evaporites. Reservoir temperatures of thermal springs determined by the Na-K geo thermometers are in the range of 56-91 deg. C, while Na-K-Ca, Na-K-Mg, Na-K-Ca-Mg and quartz geo thermometers give higher temperatures up to 177 C. Reservoir temperature determined by /sup 18/O(SO/Sub 4/-H/sub 2/O) geo thermometer ranges from 112 to 138 deg. C. There is wide variation in reservoir temperatures (54-297 deg. C) of oil fields estimated by different chemical geo thermometers. Na-K geo thermometer seems more reliable which gives close estimates to real temperature (about 100 deg. C) determined during drilling of oil wells. (author)

  4. MODIFIED REVERSE OSMOSIS SYSTEM FOR TREATMENT OF PRODUCED WATERS

    Energy Technology Data Exchange (ETDEWEB)

    T.M. Whitworth; Liangxiong Li

    2002-09-15

    This report describes work performed during the second year of the project ''Modified reverse osmosis system for treatment of produced waters.'' We performed two series of reverse osmosis experiments using very thin bentonite clay membranes compacted to differing degrees. The first series of 10 experiments used NaCl solutions with membranes that ranged between 0.041 and 0.064mm in thickness. Our results showed compaction of such ultra-thin clay membranes to be problematic. The thickness of the membranes was exceeded by the dimensional variation in the machined experimental cell and this is believed to have resulted in local bypassing of the membrane with a resultant decrease in solute rejection efficiency. In two of the experiments, permeate flow was varied as a percentage of the total flow to investigate results of changing permeate flow on solute rejection. In one experiment, the permeate flow was varied between 2.4 and 10.3% of the total flow with no change in solute rejection. In another experiment, the permeate flow was varied between 24.6 and 52.5% of the total flow. In this experiment, the solute rejection rate decreased as the permeate occupied greater fractions of the total flow. This suggests a maximum solute rejection efficiency for these clay membranes for a permeate flow of between 10.3 and 24.6% of the total; flow. Solute rejection was found to decrease with increasing salt concentration and ranged between 62.9% and 19.7% for chloride and between 61.5 and 16.8% for sodium. Due to problems with the compaction procedure and potential membrane bypassing, these rejection rates are probably not the upper limit for NaCl rejection by bentonite membranes. The second series of four reverse osmosis experiments was conducted with a 0.057mm-thick bentonite membrane and dilutions of a produced water sample with an original TDS of 196,250 mg/l obtained from a facility near Loco Hill, New Mexico, operated by an independent. These experiments

  5. A risk assessment approach to identifying constituents in oilfield produced water for treatment prior to beneficial use.

    Science.gov (United States)

    Horner, Jennifer E; Castle, James W; Rodgers, John H

    2011-05-01

    A risk assessment approach incorporating exposure pathways and calculated risk quotients was applied to identifying constituents requiring treatment prior to beneficial use of oilfield produced water (OPW). In this study, risk quotients are ratios of constituent concentrations in soil or water to guideline concentrations for no adverse effects to receptors. The risk assessment approach is illustrated by an example of an oilfield water produced from non-marine geologic strata of a rift basin in sub-Saharan Africa. The OPW studied has the following characteristics: 704-1370 mg L(-1) total dissolved solids (TDS), 45-48 mg L(-1) chloride, and 103.8 mg L(-1) oil and grease. Exposure pathways of constituents in OPW used for irrigation include: ingestion of plant tissue, ingestion and direct contact of irrigated soil by livestock, inhalation of aerosols or volatilized constituents, and ingestion of OPW directly by livestock. Applying risk quotient methods for constituents in soil and water, constituents of concern (COCs) identified for irrigation and livestock watering using the OPW studied include: iron (Fe), manganese (Mn), nickel (Ni), zinc (Zn), and oil and grease. Approximately 165,000 barrels d(-1) (26,233 m(3) d(-1)) of OPW from the study site are available for use. Identification of COCs and consideration of water quantity allows for development of reliable treatment design criteria to ensure effective and consistent treatment is achieved to meet guideline levels required for irrigation, livestock watering, or other uses. This study illustrates the utility of risk assessment for identifying the COCs in OPW for treatment, the level of treatment required, and viable options for use of the treated water. Copyright © 2011 Elsevier Inc. All rights reserved.

  6. Biogeochemistry of Produced Water from Unconventional Wells in the Powder River Basin, Wyoming

    Science.gov (United States)

    Drogos, D. L.; Nye, C.; Quillinan, S.; Urynowicz, M. A.; Wawrousek, K.

    2017-12-01

    Microbial activity in waters associated with unconventional oil and gas reservoirs is poorly described but can profoundly affect management strategies for produced water (PW), frac fluids, and biocides. Improved identification of microbial communities is required to develop targeted solutions for detrimental microbial activity such as biofouling and to exploit favorable activity such as microbial induced gas production. We quantified the microbial communities and inorganic chemistry in PW samples from cretaceous formations in six unconventional oil and gas wells in the Powder River Basin in northeast Wyoming. The wells are horizontal completions in the Frontier, Niobrara, Shannon, and Turner formations at depths of 10,000 to 12,000 feet, with PW temperatures ranging from 93oF to 130oF. Biocides utilized in frac fluids primarily included glutaraldehyde and Alkyl Dimethyl Benzyl Ammonium Chloride (ADBAC), with first production occurring in 2013. Geochemical results for PW are: pH 6.5 to 6.9; alkalinity (as CaCO3) 219 to 519 ppm; salinity 13,200 to 22,300 ppm; and TDS 39,364 to 62,725 ppm. Illumina MiSeq 16S rRNA sequencing identified the majority of communities in PW are related to anaerobic, thermophilic, halophilic, chemoheterotrophic, and chemoorganotrophic bacteria, including Thermotoga, Clostridiaceae, Thermoanaerobacter, Petrotoga, Anaerobaculum, Clostridiales, Desulfomicrobium, and Halanaerobiaceae. These findings are important for identification of biogeochemical reactions that affect the organic-inorganic-microbial interactions among reservoir rocks, formation waters, and frac fluids. Better understanding of these biogeochemical reactions would allow producers to formulate frac fluids and biocides to encourage beneficial microbial phenomena such as biogenic gas production while discouraging detrimental effects such as biofouling.

  7. Developing remediation criteria on the basis of health and ecological risks at a former sour gas plant site

    International Nuclear Information System (INIS)

    Brown, G. L.; Wilson, R. M.; Clyde, G. A.; Chollak, D. F.

    1997-01-01

    A human health and ecological risk assessment was completed for the Okotoks sour gas processing gas plant, based on the existing environmental sampling and toxicity testing that has been collected at the site since 1987. For the human health risk assessment, two potential scenarios were considered, including industrial use and parkland use. The ecological risk assessment involved synthesis of existing sampling and toxicity testing results as well as the assessment of potential risk to ecological receptors such as the meadow vole, red-tailed hawk and cattle. The assessment included chemical screening, receptor and exposure pathway selection, toxicity assessment of chemicals of concern, estimation of exposures, risk characterization and generation of soil and groundwater remediation criteria. Results of the assessments to date indicate that limited subsurface remediation is required for the protection of human health under industrial/parkland use. In contrast, ecological considerations will require remediation or reclamation of surface soil and the imposition of certain risk management controls, such as e. g. encumbrances on land title. 2 figs

  8. Elucidation of Taste- and Odor-Producing Bacteria and Toxigenic Cyanobacteria in a Midwestern Drinking Water Supply Reservoir by Shotgun Metagenomic Analysis.

    Science.gov (United States)

    Otten, Timothy G; Graham, Jennifer L; Harris, Theodore D; Dreher, Theo W

    2016-09-01

    While commonplace in clinical settings, DNA-based assays for identification or enumeration of drinking water pathogens and other biological contaminants remain widely unadopted by the monitoring community. In this study, shotgun metagenomics was used to identify taste-and-odor producers and toxin-producing cyanobacteria over a 2-year period in a drinking water reservoir. The sequencing data implicated several cyanobacteria, including Anabaena spp., Microcystis spp., and an unresolved member of the order Oscillatoriales as the likely principal producers of geosmin, microcystin, and 2-methylisoborneol (MIB), respectively. To further demonstrate this, quantitative PCR (qPCR) assays targeting geosmin-producing Anabaena and microcystin-producing Microcystis were utilized, and these data were fitted using generalized linear models and compared with routine monitoring data, including microscopic cell counts, sonde-based physicochemical analyses, and assays of all inorganic and organic nitrogen and phosphorus forms and fractions. The qPCR assays explained the greatest variation in observed geosmin (adjusted R(2) = 0.71) and microcystin (adjusted R(2) = 0.84) concentrations over the study period, highlighting their potential for routine monitoring applications. The origin of the monoterpene cyclase required for MIB biosynthesis was putatively linked to a periphytic cyanobacterial mat attached to the concrete drinking water inflow structure. We conclude that shotgun metagenomics can be used to identify microbial agents involved in water quality deterioration and to guide PCR assay selection or design for routine monitoring purposes. Finally, we offer estimates of microbial diversity and metagenomic coverage of our data sets for reference to others wishing to apply shotgun metagenomics to other lacustrine systems. Cyanobacterial toxins and microbial taste-and-odor compounds are a growing concern for drinking water utilities reliant upon surface water resources. Specific

  9. Effects of produced water on gametogenesis and gamete performance in the purple sea urchin (Stronglyocentrotus purpuratus)

    International Nuclear Information System (INIS)

    Krause, P.R.

    1993-01-01

    The author examined the effects of a chronic exposure to produced water (an oil production effluent) discharge on the gametogenesis and gamete performance of the purple sea urchin (Strongylocentrotus purpuratus) using an in situ caging experiment. Adult purple urchins were kept in benthic cages arrayed down-field from a discharging diffuser at 13 sites with distances ranging from 5m to 1,000m. Cage exposures were maintained in the field for eight weeks and each cage held 25 urchins. Gametogenesis was examined for each sex by comparing a size-independent measure of gonad mass as determined by analysis of covariance. The author found that there was a significant negative relationship between gonad mass and cage distance for both sexes, indicating that urchins living closer to the outfall produced significantly larger gonads. Gamete performance was measured through a fertilization kinetic bioassay that holds the concentration of eggs constant and varies the amount of sperm added. The proportion of eggs fertilized under each sperm concentration was determined and the response fit to a kinetics model. Significant differences were found in the fertilizability of eggs between cages. This showed a positive relationship with distance away from the outfall. The findings indicate that while adult urchins exposed to a produced water outfall produced larger gonads, they suffered a marked decreases in gamete performance

  10. Effects from offshore oil production: chronic exposure of fish to produced water

    Energy Technology Data Exchange (ETDEWEB)

    Holth, Tor Fredrik

    2009-07-01

    The results of this study demonstrated that environmentally relevant levels of components of produced water may affect condition factor, maturation, biochemical processes and gene expression in fish. The usefulness of bile PAH and AP metabolite measurements to evaluate exposure was demonstrated in two fish species. The development of bio marker responses was shown to depend on exposure regime as well as exposure period. Lysosomal stability (LMS) in cod kidney was related to dose, the effects were observed early (within two weeks) and remained at a stable level throughout the exposure period in fish receiving both continuous and pulsed exposure. Thus, LMS appeared to be a useful marker for effects in Atlantic cod. Formation of DNA adducts in female cod liver was also related to dose, but in contrast to LMS, more than 16 weeks was required for formation of significant levels. This parameter may therefore be underestimated following short-term exposures, such as most offshore fish caging studies (often 4-6 weeks). Although a time-dependent increase was observed, it also required a continuous exposure regime, which is not often observed in the environment. Other bio markers were demonstrated either to adapt or appeared to be insensitive to the exposures. CYP1A activity (EROD) in female cod was responsive on occasion, but a reduction of activity over time was observed. Protein levels of vitellogenin and hepatic CYP1A in zebra fish, as well as AOX in cod kidneys, were not affected in the current study. Gene transcription of several distinct cellular mechanisms was clearly affected in both species, and a predominance of differentially expressed genes in zebra fish was down regulated. This indicated that down-regulation of responsive pathways may be as important or more important than up-regulation. As both presence and absence of effects following pulsed exposure were apparent (DNA adduct formation; oocyte maturation; condition factor), the effects of exposure regime on

  11. Tail gas treatment of sour-SEWGS CO2 product. Public version

    Energy Technology Data Exchange (ETDEWEB)

    Van Dijk, H.A.J. [ECN Biomass and Energy Efficiency, Petten (Netherlands)

    2012-06-15

    This literature review covers the technologies suitable for the CO2-H2S separation within the context of CO2 purification of a pre-combustion captured stream intended for storage or reuse. The technologies considered cover existing industrially applied processes, emerging processes as well as processes in development. Several technologies capable of achieving the desired CO2-H2S separation were identified. Among them are liquid scrubbing processes Thiopaq and CrystaSulf producing elemental sulphur, selective oxidation to elemental sulphur such as MODOP or based on novel catalysts and sorbent-based (reactive) separations using low-, medium- or high-temperature (reactive) sorbents. SEWGS stands for Sorption Enhanced Water Gas Shift process.

  12. Complete chemical analysis of produced water by modern inductively coupled plasma spectroscopy (ICP)

    Energy Technology Data Exchange (ETDEWEB)

    Graham, G M; Sorbie, K S; Johnston, A; Boak, L S

    1997-12-31

    ICP (Inductively Coupled Plasma) spectroscopy is recognised as a very effective tool for monitoring ion compositions in many different waters. It has also been used by a number of laboratories to determine residual levels of phosphonate (PH) scale inhibitors in produced waters, based on phosphorus content. Until recently, it had not been used effectively to monitor phosphino-polycarboxylate (PPCA) returns. Large errors had frequently been observed where it had been applied. The poor detection limits and accuracy obtained for PPCA inhibitors relates to much lower amount of phosphorus present when compared with a typical phosphonate inhibitor. This paper demonstrates the effectiveness of IPC detection for PPCA and other phosphorus containing inhibitors by the use of modern instruments without the need of pre-treatment. 6 refs., 3 figs., 10 tabs.

  13. Insights into the subsurface transport of As(V) and Se(VI) in produced water from hydraulic fracturing using soil samples from Qingshankou Formation, Songliao Basin, China.

    Science.gov (United States)

    Chen, Season S; Sun, Yuqing; Tsang, Daniel C W; Graham, Nigel J D; Ok, Yong Sik; Feng, Yujie; Li, Xiang-Dong

    2017-04-01

    Produced water is a type of wastewater generated from hydraulic fracturing, which may pose a risk to the environment and humans due to its high ionic strength and the presence of elevated concentrations of metals/metalloids that exceed maximum contamination levels. The mobilization of As(V) and Se(VI) in produced water and selected soils from Qingshankou Formation in the Songliao Basin in China were investigated using column experiments and synthetic produced water whose quality was representative of waters arising at different times after well creation. Temporal effects of produced water on metal/metalloid transport and sorption/desorption were investigated by using HYDRUS-1D transport modelling. Rapid breakthrough and long tailings of As(V) and Se(VI) transport were observed in Day 1 and Day 14 solutions, but were reduced in Day 90 solution probably due to the elevated ionic strength. The influence of produced water on the hydrogeological conditions (i.e., change between equilibrium and non-equilibrium transport) was evidenced by the change of tracer breakthrough curves before and after the leaching of produced water. This possibly resulted from the sorption of polyacrylamide (PAM (-CH 2 CHCONH 2 -) n ) onto soil surfaces, through its use as a friction reducer in fracturing solutions. The sorption was found to be reversible in this study. Minimal amounts of sorbed As(V) were desorbed whereas the majority of sorbed Se(VI) was readily leached out, to an extent which varied with the composition of the produced water. These results showed that the mobilization of As(V) and Se(VI) in soil largely depended on the solution pH and ionic strength. Understanding the differences in metal/metalloid transport in produced water is important for proper risk management. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Occurrence of multi-antibiotic resistant Pseudomonas spp. in drinking water produced from karstic hydrosystems.

    Science.gov (United States)

    Flores Ribeiro, Angela; Bodilis, Josselin; Alonso, Lise; Buquet, Sylvaine; Feuilloley, Marc; Dupont, Jean-Paul; Pawlak, Barbara

    2014-08-15

    Aquatic environments could play a role in the spread of antibiotic resistance genes by enabling antibiotic-resistant bacteria transferred through wastewater inputs to connect with autochthonous bacteria. Consequently, drinking water could be a potential pathway to humans and animals for antibiotic resistance genes. The aim of this study was to investigate occurrences of Escherichia coli and Pseudomonas spp. in drinking water produced from a karst, a vulnerable aquifer with frequent increases in water turbidity after rainfall events and run-offs. Water samples were collected throughout the system from the karstic springs to the drinking water tap during three non-turbid periods and two turbid events. E. coli densities in the springs were 10- to 1000-fold higher during the turbid events than during the non-turbid periods, indicating that, with increased turbidity, surface water had entered the karstic system and contaminated the spring water. However, no E. coli were isolated in the drinking water. In contrast, Pseudomonas spp. were isolated from the drinking water only during turbid events, while the densities in the springs were from 10- to 100-fold higher than in the non-turbid periods. All the 580 Pseudomonas spp. isolates obtained from the sampling periods were resistant (to between 1 and 10 antibiotics), with similar resistance patterns. Among all the Pseudomonas isolated throughout the drinking water production system, between 32% and 86% carried the major resistance pattern: ticarcillin, ticarcillin-clavulanic acid, cefsulodin, and/or aztreonam, and/or sulfamethoxazol-trimethoprim, and/or fosfomycin. Finally, 8 Pseudomonas spp. isolates, related to the Pseudomonas putida and Pseudomonas fluorescens species, were isolated from the drinking water. Thus, Pseudomonas could be involved in the dissemination of antibiotic resistance via drinking water during critical periods. Copyright © 2014 Elsevier B.V. All rights reserved.

  15. Amine functionalized magnetic nanoparticles for removal of oil droplets from produced water and accelerated magnetic separation

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Saebom, E-mail: saebomko@austin.utexas.edu [University of Texas, Department of Petroleum and Geosystems Engineering (United States); Kim, Eun Song [University of Texas, Department of Biomedical Engineering (United States); Park, Siman [University of Texas, Department of Civil, Architectural and Environmental Engineering (United States); Daigle, Hugh [University of Texas, Department of Petroleum and Geosystems Engineering (United States); Milner, Thomas E. [University of Texas, Department of Biomedical Engineering (United States); Huh, Chun [University of Texas, Department of Petroleum and Geosystems Engineering (United States); Bennetzen, Martin V. [Maersk Oil Corporate (Denmark); Geremia, Giuliano A. [Maersk Oil Research and Technology Centre (Qatar)

    2017-04-15

    Magnetic nanoparticles (MNPs) with surface coatings designed for water treatment, in particular for targeted removal of contaminants from produced water in oil fields, have drawn considerable attention due to their environmental merit. The goal of this study was to develop an efficient method of removing very stable, micron-scale oil droplets dispersed in oilfield produced water. We synthesized MNPs in the laboratory with a prescribed surface coating. The MNPs were superparamagnetic magnetite, and the hydrodynamic size of amine functionalized MNPs ranges from 21 to 255 nm with an average size of 66 nm. The initial oil content of 0.25 wt.% was reduced by as much as 99.9% in separated water. The electrostatic attraction between negatively charged oil-in-water emulsions and positively charged MNPs controls, the attachment of MNPs to the droplet surface, and the subsequent aggregation of the electrically neutral oil droplets with attached MNPs (MNPs-oils) play a critical role in accelerated and efficient magnetic separation. The total magnetic separation time was dramatically reduced to as short as 1 s after MNPs, and oil droplets were mixed, in contrast with the case of free, individual MNPs with which separation took about 36∼72 h, depending on the MNP concentrations. Model calculations of magnetic separation velocity, accounting for the MNP magnetization and viscous drag, show that the total magnetic separation time will be approximately 5 min or less, when the size of the MNPs-oils is greater than 360 nm, which can be used as an optimum operating condition.

  16. Treatment of Simulated Coalbed Methane Produced Water Using Direct Contact Membrane Distillation

    Directory of Open Access Journals (Sweden)

    Dong-Wan Cho

    2016-05-01

    Full Text Available Expolitation of coalbed methane (CBM involves production of a massive amount saline water that needs to be properly managed for environmental protection. In this study, direct contact membrane distillation (DCMD was utilized for treatment of CBM-produced water to remove saline components in the water. Simulated CBM waters containing varying concentrations of NaCl (1, 20, and 500 mM and NaHCO3 (1 and 25 mM were used as feed solutions under two transmembrane temperatures (Δ40 and 60 °C. In short-term distillation (~360 min, DCMD systems showed good performance with nearly 100% removal of salts for all solutes concentrations at both temperatures. The permeate flux increased with the feed temperature, but at a given temperature, it remained fairly stable throughout the whole operation. A gradual decline in permeate flux was observed at Δ60 °C at high NaHCO3 concentration (25 mM. In long-term distillation (5400 min, the presence of 25 mM NaHCO3 further decreased the flux to 25%–35% of the initial value toward the end of the operation, likely due to membrane fouling by deposition of Ca-carbonate minerals on the pore openings. Furthermore, pore wetting by the scalants occurred at the end of the experiment, and it increased the distillate conducitivity to 110 µS·cm−1. The precipitates formed on the surface were dominantly CaCO3 crystals, identified as aragonite.

  17. Produced water silica removal treatment in PETROBRAS Fazenda Belem fields - Brazil; Tratamento da agua produzida do Campo de Fazenda Belem (PETROBRAS, UN/RNCE) para remocao de silica

    Energy Technology Data Exchange (ETDEWEB)

    Junior, Agenor J.; Sampaio, Alberto C.; Silva, Arnaldo F. da; Christiano, Fernando P.; Freire, Norma de O.; Pereira Junior, Oswaldo de A. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

    2008-07-01

    Extracting oil from mature fields generates huge volumes of produced water whose pollutive character requires adequate treatment to minimize environmental impact. Nevertheless, produced water may be re-used, avoiding environmental contamination and helping in water resources preservation. According to future use, produced water receives specific treatment, intending to remove critical contaminants to the application involved. In the case o UN/RNCE's Fazenda Belem Field produced water is treated for steam generation Membrane Separation Processes are currently in test for this treatment. These processes are sensitive to high water hardness and silica concentrations. To avoid scaling, caustic soda is added in the water-oil separator outlet, precipitating calcium carbonate and magnesium hydroxide. This treatment, however, helps solubilizing silica. Coagulation-flocculation laboratory tests were run with poly aluminum chloride (PAC) and magnesium chloride at constant temperature (45 deg C) and pH adjusted to 9,5, attempting to simulate the water-oil separator outlet conditions. Laboratory analysis showed good silica removal results only in samples treated with PAC, suggesting its use in produced water for steam generation pre-treatment, avoiding silica-based scaling in membranes. (author)

  18. Pathogenic Escherichia coli producing Extended-Spectrum β-Lactamases isolated from surface water and wastewater.

    Science.gov (United States)

    Franz, Eelco; Veenman, Christiaan; van Hoek, Angela H A M; de Roda Husman, Ana; Blaak, Hetty

    2015-09-24

    To assess public health risks from environmental exposure to Extended-Spectrum β-Lactamases (ESBL)-producing bacteria, it is necessary to have insight in the proportion of relative harmless commensal variants and potentially pathogenic ones (which may directly cause disease). In the current study, 170 ESBL-producing E. coli from Dutch wastewater (n = 82) and surface water (n = 88) were characterized with respect to ESBL-genotype, phylogenetic group, resistance phenotype and virulence markers associated with enteroaggregative E. coli (EAEC), enteroinvasive E. coli (EIEC), enteropathogenic E. coli (EPEC), enterotoxigenic E. coli (ETEC), extraintesinal E. coli (ExPEC), and Shiga toxin-producing E. coli (STEC). Overall, 17.1% of all ESBL-producing E. coli were suspected pathogenic variants. Suspected ExPECs constituted 8.8% of all ESBL-producing variants and 8.3% were potential gastrointestinal pathogens (4.1% EAEC, 1.8% EPEC, 1.2% EIEC, 1.2% ETEC, no STEC). Suspected pathogens were significantly associated with ESBL-genotype CTX-M-15 (X(2) = 14.7, P antibiotics. In conclusion, this study demonstrates that the aquatic environment is a potential reservoir of E. coli variants that combine ESBL-genes, a high level of multi-drug resistance and virulence factors, and therewith pose a health risk to humans upon exposure.

  19. Energy Saving in an ETC Solar System to Produce High Temperature Water

    Directory of Open Access Journals (Sweden)

    Carlos J. Porras-Prieto

    2018-04-01

    Full Text Available The use of solar water heating systems (SWHS based on evacuated tube collectors (ETC has experienced rapid growth in the residential sector. In contrast, the implementation of these systems in the industrial sector is very limited, due in part to the demand of a higher temperature in water. Taking into account that the final energy of the industrial sector is similar to the residential sector, to increase the generation of renewable energy and energy saving in cities, efforts in this sector should be redoubled. Therefore, the present work characterises the behaviour of a SWHS-ETC with active circulation to produce hot water at 90 °C, determining its performance, energy saving and profitability in different scenarios in Europe. The annual energy savings generated by the SWHS Range between 741 and 435 kWh m−2 (reduction of emissions between 215 and 88 kg CO2 m−2. The results of the analysis of profitability, studying the variation of the conventional energy price, the cost of the investment, the useful life and the energy supplied, in thousands of scenarios, are a valuable tool for correct decision making, as they can be of great utility to increase the implementation of these systems in the industrial sector.

  20. Water use efficiency of coriander produced in a low-cost hydroponic system

    Directory of Open Access Journals (Sweden)

    José A. Santos Júnior

    2015-12-01

    Full Text Available ABSTRACT The increase of water use efficiency in crop production is a clear need in areas with restricted access to this resource and, in these cases, the adoption of forms of cultivation contextualized to local conditions are essential. Thus, the implications of the variation in the amount of seeds per cell (0.5, 1.0, 1.5 and 2.0 g and spacing between cells (7.0, 10.0 and 15.0 cm on variables related to consumption and water use efficiency for the production of coriander (cv. Tabocas in a low-cost hydroponic system, an alternative for semiarid regions, were evaluated. A completely randomized experimental design, analysed in 4 x 3 factorial scheme with three replicates, was adopted, and the data were subjected to analysis of variance at 0.05 probability level. It was found that the reduction in the spacing between cells has a better cost-benefit ratio with respect to water consumption, biomass produced and cost of seeds. Therefore, it is recommended the adoption of a spacing of 7.0 cm between cells and the use of 1.0 g seeds per cell; this configuration promoted efficiency of 81.59 g L-1 in shoot green mass production and total mass of 62.4 g coriander bunches.

  1. The importance of bee pollination of the sour cherry (Prunus cerasus Cultivar ‘Stevnsbaer’ in Denmark

    Directory of Open Access Journals (Sweden)

    Lise Hansted

    2012-12-01

    Full Text Available Low fruit set, despite normally-developed flowers, is often a significant contributor to poor yield of the self-fertile sour cherry (Prunus cerasus cultivar ‘Stevnsbaer’ in Denmark. The aim of this study was to investigate the effect of insect, and particularly, bee pollination on the fruit set of this cultivar, in order to provide orchard management information for both Danish ‘Stevnsbaer’ growers and beekeepers. Visits to cherry flowers by honey bees (Apis mellifera, Bombus species and solitary bees, were recorded during the flowering of ‘Stevnsbaer’ in five separate Danish orchards. The results indicate that there is a significantly higher fruit set on open pollinated branches when compared to caged branches, where bees and other pollinating insects where excluded. The results were qualitatively consistent over three different seasons (2007, 2009 and 2010. A period of prolonged cold, humid weather before and during early flowering probably reduced fruit set significantly in 2010 compared to 2009. Regarding the apparent benefits of bee pollination on fruit set and subsequent implications for yield, we recommend placing honeybees in ‘Stevnsbaer’ orchards during flowering to sustain commercially viable production. Another valuable management strategy would be to improve foraging and nesting conditions to support both honey and wild bees in and around the orchards.

  2. The study on process of recycling uranium in mixture of residue and liquid

    International Nuclear Information System (INIS)

    Zhang Jie; Shen Weiwei; Hao Jidong; Wu Jiangming

    2014-01-01

    The treat method of mixture of residue and liquid produced from HWR nuclear fuel chemical process using some kind of U_3O_8 powder was studied in this experiment. For recycling the uranium in mixture of residue and liquid, chemical dissolving method, washing and centrifuging method and dilute nitric acid leaching uranium method was contrasted in this test. The merit of dilute nitric acid leaching uranium method is simpler, more effective and higher uranium recycling ratio. Next, dilute nitric acid leaching uranium method was studied systematically. As a result, the main influence factors of uranium recycling ratio is dip sour degree and dip sour temperature. The influence law of factors to uranium recycling ratio and filtering effect was found out also. Along with increasing of dip sour degree and dip sour temperature, uranium recycling ratio increases and speed of filtrate increases also. At last, the process of batch treating mixture of residue and liquid was build and abundant uranium was recycled. (authors)

  3. Amelioration of radiation induced oxidative stress using water soluble chitosan produced by Aspergillus niger

    International Nuclear Information System (INIS)

    EL-Sonbaty, S.M.; Swailam, H.M.; Noaman, E.

    2012-01-01

    Chitosan is a natural polysaccharide synthesized by a great number of living organisms and considered as a source of potential bioactive material and has many biological applications which are greatly affected by its solubility in neutral ph. In this study low molecular weight water soluble chitosan was prepared by chemical degradation of chitosan produced by Aspergillus niger using H 2 O 2 . Chitosan chemical structure was detected before and after treatment using FTIR spectrum, and its molecular weight was determined by its viscosity using viscometer. Its antioxidant activity against gamma radiation was evaluated in vivo using rats. Rats were divided into 4 groups; group 1: control, group 2: exposed to acute dose of gamma radiation (6 Gy), group 3: received water soluble chitosan, group 4: received water soluble chitosan then exposed to gamma radiation as group 2. Gamma radiation significantly increased malonaldehyde, decreased glutathione concentration, activity of superoxide dismutase, catalase, and glutatione peroxidase, while significantly increase the activity of alanine transferase, aspartate transferase, urea and creatinine concentration. Administration of water soluble chitosan has ameliorated induced changes caused by gamma radiation. It could be concluded that water soluble chitosan by scavenging free radicals directly or indirectly may act as a potent radioprotector against ionizing irradiation.

  4. The survey reasarch about groundwater in a mine making use of the sour method to immerse at originl place in Xinjiang province

    International Nuclear Information System (INIS)

    Xu Yiqun; Yang Yihan

    2014-01-01

    Basing on a mine making use of a sour method to immerse at original place in Xiniang province, building up a monitor network of mine and its Surroundings groundwater, by the mispreads experiment at the spot and the Earth physical method to mointer Pollute scope and imitate the flow of groundwater and the movement of dissolve quality. Making use of the method speaking of to investigate groundwater in mineral layer completely. According to the investigating result, Comparing the original date of groundwater in mineral layer and the national Quality standard of groundwater to evaluate the present Pollute condition of groundwater existmg in the A # , B # mine ore aquifer. This studies Proves that Pollution mainly exists in the A # , B # mine ore aquifer and its surrounding limited area, groundwater upper or lower the ore aquifer is not affected by pollution. (authors)

  5. Direct observation of an isopolyhalomethane O-H insertion reaction with water: Picosecond time-resolved resonance Raman (ps-TR3) study of the isobromoform reaction with water to produce a CHBr2OH product

    International Nuclear Information System (INIS)

    Kwok, W.M.; Zhao Cunyuan; Li Yunliang; Guan Xiangguo; Phillips, David Lee

    2004-01-01

    Picosecond time-resolved resonance Raman (ps-TR 3 ) spectroscopy was used to obtain the first definitive spectroscopic observation of an isopolyhalomethane O-H insertion reaction with water. The ps-TR 3 spectra show that isobromoform is produced within several picoseconds after photolysis of CHBr 3 and then reacts on the hundreds of picosecond time scale with water to produce a CHBr 2 OH reaction product. Photolysis of low concentrations of bromoform in aqueous solution resulted in noticeable formation of HBr strong acid. Ab initio calculations show that isobromoform can react with water to produce a CHBr 2 (OH) O-H insertion reaction product and a HBr leaving group. This is consistent with both the ps-TR 3 experiments that observe the reaction of isobromoform with water to form a CHBr 2 (OH) product and photolysis experiments that show HBr acid formation. We briefly discuss the implications of these results for the phase dependent behavior of polyhalomethane photochemistry in the gas phase versus water solvated environments

  6. Comparison of Extended-Spectrum β-Lactamase-Producing Escherichia coli Isolates from Drinking Well Water and Pit Latrine Wastewater in a Rural Area of China

    Directory of Open Access Journals (Sweden)

    Hongna Zhang

    2016-01-01

    Full Text Available The present study was conducted to gain insights into the occurrence and characteristics of extended-spectrum beta-lactamase- (ESBL- producing Escherichia coli (E. coli from drinking well water in the rural area of Laiwu, China, and to explore the role of the nearby pit latrine as a contamination source. ESBL-producing E. coli from wells were compared with isolates from pit latrines in the vicinity. The results showed that ESBL-producing E. coli isolates, with the same antibiotic resistance profiles, ESBL genes, phylogenetic group, plasmid replicon types, and enterobacterial repetitive intergenic consensus-polymerase chain reaction (ERIC-PCR fingerprints, were isolated from well water and the nearby pit latrine in the same courtyard. Therefore, ESBL-producing E. coli in the pit latrine may be a likely contributor to the presence of ESBL-producing E. coli in rural well water.

  7. Multidrug-Resistant and Extended Spectrum Beta-Lactamase-Producing Escherichia coli in Dutch Surface Water and Wastewater.

    Directory of Open Access Journals (Sweden)

    Hetty Blaak

    Full Text Available The goal of the current study was to gain insight into the prevalence and concentrations of antimicrobial resistant (AMR Escherichia coli in Dutch surface water, and to explore the role of wastewater as AMR contamination source.The prevalence of AMR E. coli was determined in 113 surface water samples obtained from 30 different water bodies, and in 33 wastewater samples obtained at five health care institutions (HCIs, seven municipal wastewater treatment plants (mWWTPs, and an airport WWTP. Overall, 846 surface water and 313 wastewater E. coli isolates were analysed with respect to susceptibility to eight antimicrobials (representing seven different classes: ampicillin, cefotaxime, tetracycline, ciprofloxacin, streptomycin, sulfamethoxazole, trimethoprim, and chloramphenicol.Among surface water isolates, 26% were resistant to at least one class of antimicrobials, and 11% were multidrug-resistant (MDR. In wastewater, the proportions of AMR/MDR E. coli were 76%/62% at HCIs, 69%/19% at the airport WWTP, and 37%/27% and 31%/20% in mWWTP influents and effluents, respectively. Median concentrations of MDR E. coli were 2.2×10(2, 4.0×10(4, 1.8×10(7, and 4.1×10(7 cfu/l in surface water, WWTP effluents, WWTP influents and HCI wastewater, respectively. The different resistance types occurred with similar frequencies among E. coli from surface water and E. coli from municipal wastewater. By contrast, among E. coli from HCI wastewater, resistance to cefotaxime and resistance to ciprofloxacin were significantly overrepresented compared to E. coli from municipal wastewater and surface water. Most cefotaxime-resistant E. coliisolates produced ESBL. In two of the mWWTP, ESBL-producing variants were detected that were identical with respect to phylogenetic group, sequence type, AMR-profile, and ESBL-genotype to variants from HCI wastewater discharged onto the same sewer and sampled on the same day (A1/ST23/CTX-M-1, B23/ST131/CTX-M-15, D2/ST405/CTX-M-15.In

  8. Surface modification of ultra thin PES-zeolite using thermal annealing to increase flux and rejection of produced water treatment

    Energy Technology Data Exchange (ETDEWEB)

    Kusworo, T. D., E-mail: tdkusworo@che.undip.ac.id; Widayat,; Pradini, A. W.; Armeli, Y. P. [Department of Chemical Engineering, University of Diponegoro Prof. Soedarto, Tembalang, Semarang, 50239, Phone/Fax : (024) 7460058 (Indonesia)

    2015-12-29

    Membrane technology is an alternative of water treatment based on filtration that is being developed. Surface Modification using heat treatment has been investigated to improve the performance of ultra thin PES-Zeolite nanocomposite membrane for produced water treatment from Pertamina Balongan. Two types of membranes with surface modification and without modification were prepared to study the effect of surface modification on its permeation properties. Asymmetric ultra thin PES-Zeolite nanocomposite membrane for produced water treatment was casted using the dry/wet phase inversion technique from dope solutions containing polyethersulfone, N-methyl-2-pyrrolidone (NMP) as a solvent and zeolite as a filler. Experimental results showed that the heat treatment at near glass transition temperature was increase the rejection of COD, Turbidity and ion Ca{sup 2+}. The better adherence of zeolite particles in the polymer matrix combined with formation of charge transfer complexes (CTCs) and cross-linking might be the main factors to enhance the percent of rejection. Field emission scanning electron microscopy (FESEM) micrographs showed that the selective layer and the substructure of PES-zeolite membrane became denser and more compact after the heat treatment. The FESEM micrographs also showed that the heat treatment was increased the adherence of zeolite particle and polymer. Membranes treated at 180 °C for 15 seconds indicated increase the rejection and small decrease in flux for produced water treatment.

  9. Inhibiting mild steel corrosion from sulfate-reducing bacteria using antimicrobial-producing biofilms in Three-Mile-Island process water.

    Science.gov (United States)

    Zuo, R; Ornek, D; Syrett, B C; Green, R M; Hsu, C-H; Mansfeld, F B; Wood, T K

    2004-04-01

    Biofilms were used to produce gramicidin S (a cyclic decapeptide) to inhibit corrosion-causing, sulfate-reducing bacteria (SRB). In laboratory studies these biofilms protected mild steel 1010 continuously from corrosion in the aggressive, cooling service water of the AmerGen Three-Mile-Island (TMI) nuclear plant, which was augmented with reference SRB. The growth of both reference SRB (Gram-positive Desulfosporosinus orientis and Gram-negative Desulfovibrio vulgaris) was shown to be inhibited by supernatants of the gramicidin-S-producing bacteria as well as by purified gramicidin S. Electrochemical impedance spectroscopy and mass loss measurements showed that the protective biofilms decreased the corrosion rate of mild steel by 2- to 10-fold when challenged with the natural SRB of the TMI process water supplemented with D. orientis or D. vulgaris. The relative corrosion inhibition efficiency was 50-90% in continuous reactors, compared to a biofilm control which did not produce the antimicrobial gramicidin S. Scanning electron microscope and reactor images also revealed that SRB attack was thwarted by protective biofilms that secrete gramicidin S. A consortium of beneficial bacteria (GGPST consortium, producing gramicidin S and other antimicrobials) also protected the mild steel.

  10. The effects of the lodgepole sour gas well blowout on coniferous tree growth

    International Nuclear Information System (INIS)

    Baker, K.A.

    1991-01-01

    A dendrochronological study was used to evaluate growth impacts on White Spruce (Picea glauca (Moench) resulting from the 1982 Lodgepole sour gas well blowout. Stem analysis was evaluated from four ecologically similar monitoring sites located on a 10 kilometre downwind gradient and compared to a control site. Incremental volume was calculated, standardized using running mean filters and analyzed using one-way ANOVA. Pre and post-blowout growth trends were analyzed between sites and were also evaluated over a height profile in order to assess growth impact variability within individual trees. Growth reductions at the two sites closest the wellhead were statistically significant for five post-blowout years. Growth at these condensate impacted sites was reduced to 9.8% and 38.1% in 1983. Differences in growth reductions reflect a gradient of effects and a dose-response relationship. Recovery of surviving trees has been rapid but is leveling off at approximately 80% of pre-blowout growth. growth reductions were greater and recovery rates slower than those previously predicted by other authors. Statistically significant differences in height profile growth responses were limited to the upper portions of the trees. Growth rates over a tree height profile ranged from 10% less to 50% more than growth rates observed at a 1.3 metres. Analytical methodologies detected and described growth differences over a height profile but a larger sample size was desirable. As is always the case in catastrophic events, obtaining pre-event baseline data is often difficult. Dendrochronological methods described in this paper offer techniques for determining pre-blowout growth and monitoring impacts and recovery in forested areas

  11. Acid stimulation (sour taste elicits GABA and serotonin release from mouse taste cells.

    Directory of Open Access Journals (Sweden)

    Yijen A Huang

    Full Text Available Several transmitter candidates including serotonin (5-HT, ATP, and norepinephrine (NE have been identified in taste buds. Recently, γ-aminobutyric acid (GABA as well as the associated synthetic enzymes and receptors have also been identified in taste cells. GABA reduces taste-evoked ATP secretion from Receptor cells and is considered to be an inhibitory transmitter in taste buds. However, to date, the identity of GABAergic taste cells and the specific stimulus for GABA release are not well understood. In the present study, we used genetically-engineered Chinese hamster ovary (CHO cells stably co-expressing GABA(B receptors and Gαqo5 proteins to measure GABA release from isolated taste buds. We recorded robust responses from GABA biosensors when they were positioned against taste buds isolated from mouse circumvallate papillae and the buds were depolarized with KCl or a stimulated with an acid (sour taste. In contrast, a mixture of sweet and bitter taste stimuli did not trigger GABA release. KCl- or acid-evoked GABA secretion from taste buds was Ca(2+-dependent; removing Ca(2+ from the bathing medium eliminated GABA secretion. Finally, we isolated individual taste cells to identify the origin of GABA secretion. GABA was released only from Presynaptic (Type III cells and not from Receptor (Type II cells. Previously, we reported that 5-HT released from Presynaptic cells inhibits taste-evoked ATP secretion. Combined with the recent findings that GABA depresses taste-evoked ATP secretion, the present results indicate that GABA and 5-HT are inhibitory transmitters in mouse taste buds and both likely play an important role in modulating taste responses.

  12. Cassava starch in the Brazilian food industry

    Directory of Open Access Journals (Sweden)

    Ivo Mottin Demiate

    2011-06-01

    Full Text Available Cassava starch is a valued raw material for producing many kinds of modified starches for food applications. Its physicochemical properties, as well as its availability, have made it an interesting and challenging ingredient for the food industry. In the present work, food grade modified cassava starches were purchased from producers and analyzed for selected physicochemical characteristics. Samples of sour cassava starch were included, as well as one sample of native cassava starch. Results showed that almost all modified starches were resistant to syneresis, produced pastes more stable to stirred cooking, and some of them were difficult to cook. The sour cassava starches presented high acidity and resulted in clear and unstable pastes during stirred cooking, susceptible to syneresis.

  13. Competitive, microbially-mediated reduction of nitrate with sulfide and aromatic oil components in a low-temperature, western Canadian oil reservoir.

    Science.gov (United States)

    Lambo, Adewale J; Noke, Kim; Larter, Steve R; Voordouw, Gerrit

    2008-12-01

    Fields from which oil is produced by injection of sulfate-bearing water often exhibit an increase in sulfide concentration with time (souring). Nitrate added to the injection water lowers the sulfide concentration by the action of sulfide-oxidizing, nitrate-reducing bacteria (SO-NRB). However, the injected nitrate can also be reduced with oil organics by heterotrophic NRB (hNRB). Aqueous volatile fatty acids (VFAs; a mixture of acetate, propionate, and butyrate) are considered important electron donors in this regard. Injection and produced waters from a western Canadian oil field with a low in situ reservoir temperature (30 degrees C) had only 0.1-0.2 mM VFAs. Amendment of these waters with nitrate gave therefore only partial reduction. More nitrate was reduced when 2% (v/v) oil was added, with light oil giving more reduction than heavy oil. GC-MS analysis of in vitro degraded oils and electron balance considerations indicated that toluene served as the primary electron donor for nitrate reduction. The differences in the extent of nitrate reduction were thus related to the toluene content of the light and heavy oil (30 and 5 mM, respectively). Reduction of nitrate with sulfide by SO-NRB always preceded that with oil organics by hNRB, even though microbially catalyzed kinetics with either electron donor were similar. Inhibition of hNRB by sulfide is responsible for this phenomenon. Injected nitrate will thus initially be reduced with sulfide through the action of SO-NRB. However, once sulfide has been eliminated from the near-injection wellbore region, oil organics will be targeted by the action of hNRB. Hence, despite the kinetic advantage of SO-NRB, the nitrate dose required to eliminate sulfide from a reservoir depends on the concentration of hNRB-degradable oil organics, with toluene being the most important in the field under study. Because the toluene concentration is lower in heavy oilthan in light oil, nitrate injection into a heavy-oil-producing field of

  14. Hydrogen sulfide (H{sub 2}S) and sour gas effects on the eye. A historical perspective

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, Timothy William [Environmental Health, Calgary Health Region, 1509 Centre St SW, Calgary Alberta, T2G 2E6 (Canada)]. E-mail: tim.lambert@calgaryheathregion.ca; Goodwin, Verona Marie [VM Goodwin Research and Consulting Ltd. (Canada); Stefani, Dennis [Environmental Health, Calgary Health Region, 1509 Centre St SW, Calgary Alberta, T2G 2E6 (Canada); Strosher, Lisa [Environmental Health, Calgary Health Region, 1509 Centre St SW, Calgary Alberta, T2G 2E6 (Canada)

    2006-08-15

    pyknosis, edema and separation of cells in the eye following exposures for 3 h at 36 ppm H{sub 2}S [Michal FV. Eye lesions caused by hydrogen sulfide. Cesk Ophthalmol 1950;6;5-8]. In 1975, in Alberta, irreversible eye damage and photophobia were experimentally produced in calves exposed to 20 ppm H{sub 2}S for 1 week [Nordstrom GA. A study of calf response of ammonia and hydrogen sulfide gases. Thesis, University of Alberta, Department of Agricultural Engineering, Edmonton Alberta; 1975, 218 pp.]. Alberta Environmental Centre documented clinical irritation of the eye at 40 ppm H{sub 2}S in 6 hours in rats [Alberta Environmental Centre. Morphological observations in rats exposed for six hours to an atmosphere of 0, 56, or 420 mg/m{sup 3} hydrogen sulfide. AECV86-A1. Alberta Environmental Centre, Vegreville, Alberta; 1986b. 28 pp.]. In two sour gas blow-outs in Alberta, in the early 1980s, eye injury was documented in humans and animals at 0.5 ppm H{sub 2}S. Community studies in the United States, Europe and New Zealand suggest that acute exposure to 25 ppb H{sub 2}S is the lowest concentration to irritate the eyes; with chronic exposure, serious eye effects are suggested. In contrast to the conclusion, all of the studies, except one, cited in the AHW Report indicate toxic effects on the eye below 100 ppm H{sub 2}S [Alberta Health and Wellness (AHW report). Health effects associated with short-term exposure to low levels of hydrogen sulfide (H{sub 2}S): a technical review, Alberta Health and Wellness, October 2002, 81pp.]. In addition, the AHW Report (2002) mis-presented two studies as 'clinical studies', claiming they reported no evidence of eye effects in humans from 2 and 30 ppm H{sub 2}S for 30-40 minutes [Alberta Health and Wellness (AHW report). Health effects associated with short-term exposure to low levels of hydrogen sulfide (H{sub 2}S): a technical review, Alberta Health and Wellness, October 2002, 81pp.].

  15. Insights into the subsurface transport of As(V) and Se(VI) in produced water from hydraulic fracturing using soil samples from Qingshankou Formation, Songliao Basin, China.

    OpenAIRE

    Chen, SS; Sun, Y; Tsang, DC; Graham, NJ; Ok, YS; Feng, Y; Li, XD

    2017-01-01

    Produced water is a type of wastewater generated from hydraulic fracturing, which may pose a risk to the environment and humans due to its high ionic strength and the presence of elevated concentrations of metals/metalloids that exceed maximum contamination levels. The mobilization of As(V) and Se(VI) in produced water and selected soils from Qingshankou Formation in the Songliao Basin in China were investigated using column experiments and synthetic produced water whose quality was represent...

  16. Methods and systems for producing syngas

    Science.gov (United States)

    Hawkes, Grant L; O& #x27; Brien, James E; Stoots, Carl M; Herring, J. Stephen; McKellar, Michael G; Wood, Richard A; Carrington, Robert A; Boardman, Richard D

    2013-02-05

    Methods and systems are provided for producing syngas utilizing heat from thermochemical conversion of a carbonaceous fuel to support decomposition of at least one of water and carbon dioxide using one or more solid-oxide electrolysis cells. Simultaneous decomposition of carbon dioxide and water or steam by one or more solid-oxide electrolysis cells may be employed to produce hydrogen and carbon monoxide. A portion of oxygen produced from at least one of water and carbon dioxide using one or more solid-oxide electrolysis cells is fed at a controlled flow rate in a gasifier or combustor to oxidize the carbonaceous fuel to control the carbon dioxide to carbon monoxide ratio produced.

  17. Carbohydrate production, balance and translocation in leaves, shoots and fruits of Montmorency sour cherry

    International Nuclear Information System (INIS)

    Kappes, E.M.

    1986-01-01

    Carbohydrate production, export and use were studied for different organs of sour cherry (Prunus cerasus L. Montmorency). Gross carbohydrate ( 14 CO 2 ) export started between 27.2 and 77.6% of full leaf expansion. The 10th leaf developing started export later than the 7th leaf, suggesting that higher carbohydrate availability during leaf expansion delays export initiation. In support of this, gross export started earlier (44.4-52.4% full expansion) after source leaf removal, than in the control (77.6%). Translocation was primarily vertical (following orthostichies). Most leaves of fruiting shoots exported bidirectionally to the apex and fruits, only leaves closest to fruits exported exclusively to fruits during rapid cell division (Stage I) and rapid cell expansion (Stage III). Net export, determined from carbohydrate balance models started at 17 and 51% expansion for the 7th and terminal leaf, and at 26.5% of shoot elongation. Cumulative carbohydrate production of the 7th and terminal leaves during the first 9 and 11 days after emergence, exceeded carbohydrate accumulated at final size, 464.2 and 148.9 mg. A fruit carbohydrate balance was developed to determine contributions by fruit photosynthesis and fruit respiration, and to identify periods of greatest carbohydrate import. Fruit photosynthesis during development was characterized under different environmental conditions. Gross photosynthesis and chlorophyll content per fruit increased to a maximum during stage II and decreased thereafter. Gross photosynthesis approached a maximum at 40 0 C. Since dark respiration increased exponentially over the same temperature range, net photosynthesis reached a maximum at 18 0 C. Photorespiration was not detected

  18. Produced Water Treatment Using Geothermal Energy from Oil and Gas Wells: An Appropriateness of Decommissioned Wells Index (ADWI) Approach

    Science.gov (United States)

    Kiaghadi, A.; Rifai, H. S.

    2016-12-01

    This study investigated the feasibility of harnessing geothermal energy from retrofitted oil and gas decommissioned wells to power desalination units and overcome the produced water treatment energy barrier. Previous studies using heat transfer models have indicated that well depth, geothermal gradient, formation heat conductivity, and produced water salt levels were the most important constraints that affect the achievable volume of treated water. Thus, the challenge of identifying which wells would be best suited for retrofit as geothermal wells was addressed by defining an Appropriateness of Decommissioned Wells Index (ADWI) using a 25 km x 25 km grid over Texas. Heat transfer modeling combined with fuzzy logic methodology were used to estimate the ADWI at each grid cell using the scale of Very Poor, Poor, Average, Good and Excellent. Values for each of the four constraints were extracted from existing databases and were used to select 20 representative values that covered the full range of the data. A heat transfer model was run for all the 160,000 possible combination scenarios and the results were regressed to estimate weighting coefficients that indicate the relative effect of well depth, geothermal gradient, heat conductivity, and produced water salt levels on the volume of treated water in Texas. The results indicated that wells located in cells with ADWI of "Average", "Good" or "Excellent" can potentially deliver 35,000, 106,000, or 240,000 L/day of treated water, respectively. Almost 98% of the cells in the Granite Wash, 97% in Eagle Ford Shale, 90% in Haynesville Shale, 79% in Permian Basin, and 78% in Barnett Shale were identified as better than "Average" locations; whereas, south of the Eagle Ford, southwestern Permian Basin, and the center of Granite Wash were "Excellent". Importantly, most of the locations with better than "Average" ADWI are within drought prone agricultural regions that would benefit from this resilient source of clean water.

  19. An assessment of Osmia rufa (syn. bicornis) as a pollinator of the sour cherry (Prunus cerasus) cv. Stevnsbaer in eastern Denmark

    DEFF Research Database (Denmark)

    Hansted, Lise; Grout, Brian William Wilson; Toldam-Andersen, Torben Bo

    2014-01-01

    . The remaining 8 pollen types were from entomophilous plants. Based on the results it is estimated that a mean of 220,000 O. rufa cocoons would be needed per hectare if the species were to be an effective, supplementary pollinator of P. cerasus cv. Stevnsbaer. Practical, economic and environmental considerations...... investigates the activity and food preferences of this species during flowering of sour cherry (P. cerasus cv. Stevnsbaer). Female O. rufa provisioned a mean of 2.96 ± 1.44 cells each with 6.24 ± 1.46 pollen types during the receptive period of flowering . In all 17 different pollen types were collected...... of which the most dominant were Salix (41.4% ± 9.34%) and Acer (33.24% ± 8.81%), followed by Betula (8.16% ± 5.08%), P. cerasus (8.16% ± 1.79%) and Fagus (3.56% ± 1.96%). P. cerasus was present in all samples. Nine pollen types were from anemophilous plants and represented 87.94% of the pollen collected...

  20. Removal of Radium isotopes from oil co-produced water using Bentonite

    International Nuclear Information System (INIS)

    Al Masri, M.S.; Al Attar, L.; Budeir, Y.; Al Chayah, O.

    2010-01-01

    In view of environmental concern, sorption of radium on natural bentonite mineral (Aleppo, Syria) was investigated using batch-type method. Data were expressed in terms of distribution coefficients. An attempt to increase the selectivity of bentonite for radium was made by preparing M-derivatives. Loss of mineral crystallinity in acidic media and the formation of new phase, such as BaCO 3 , in Ba-derivative were imposed by XRD characterisations. Of the cationic forms, Na-bentonite had shown the highest affinity. Mechanisms of radium uptake were pictured using M-derivatives and simulated radium solutions. The obtained results indicated that surface sorption/surface ion exchange were the predominated processes. The distinct sorption behaviour observed with Ba-form was, possibly, a reflection of radium co-precipitation with barium carbonate. The competing order of macro component, likely present in waste streams, was drawn by studying different concentrations of the corresponding salt media. As an outcome, sodium was the weakest inhibitor. The performance of natural bentonite and the most selective forms, i.e. Ba- and Na-derivatives, to sorb radium from actual oil co-produced waters, collected form Der Ezzor Petroleum Company (DEZPC), was studied. This mirrored the influential effect of waters pH over other comparable parameters. (author)

  1. The effect of gas and oil well blowout emissions on livestock in Alberta

    International Nuclear Information System (INIS)

    Beck, B.E.

    1992-01-01

    Poisoning caused by emissions from sour gas well or oil well blowouts is not acute because the gases are diluted by the atmosphere before they reach livestock. Exposure may last a month or more and may produce a syndrome indistinguishable from common disorders of flu, malaise, mood change, and in the case of animals, lack of production or decreased production. Little information is available on the composition of releases from well blowouts, which may change due to concurrent reactions with oxygen and photodecomposition. Effects on livestock observed to results from sour gas plant emissions (mostly sulfur dioxide) include runny eyes in cattle, loss of production, diarrhea and abortion. Blowout emissions may contain oxidant gases as well as hydrogen sulfides. These products irritate mucous membranes, and can lead to pink eye. Respiratory problems may include upper respiratory tract infections, and may produce susceptibility to secondary pneumonia. Abortion, infertility and congenital effects are areas of concern. It is considered unlikely that hydrogen sulfide can cause such effects, however carbon disulfide and carbonyl sulfide, both present in sour gas blowouts, are known to have effects on the fetus. Effects on production and performance are unknown, and it is postulated that amounts of sulfur deposition are insufficient to cause nutrient deficiencies. Psychological reactions are suggested to explain some of the adverse effects of exposure to sour gas. 1 ref

  2. Elucidation of taste- and odor-producing bacteria and toxigenic cyanobacteria in a Midwestern drinking water supply reservoir by shotgun metagenomics analysis

    Science.gov (United States)

    Otten, Timothy; Graham, Jennifer L.; Harris, Theodore D.; Dreher, Theo

    2016-01-01

    While commonplace in clinical settings, DNA-based assays for identification or enumeration of drinking water pathogens and other biological contaminants remain widely unadopted by the monitoring community. In this study, shotgun metagenomics was used to identify taste-and-odor producers and toxin-producing cyanobacteria over a 2-year period in a drinking water reservoir. The sequencing data implicated several cyanobacteria, including Anabaena spp.,Microcystis spp., and an unresolved member of the order Oscillatoriales as the likely principal producers of geosmin, microcystin, and 2-methylisoborneol (MIB), respectively. To further demonstrate this, quantitative PCR (qPCR) assays targeting geosmin-producing Anabaena and microcystin-producing Microcystis were utilized, and these data were fitted using generalized linear models and compared with routine monitoring data, including microscopic cell counts, sonde-based physicochemical analyses, and assays of all inorganic and organic nitrogen and phosphorus forms and fractions. The qPCR assays explained the greatest variation in observed geosmin (adjusted R2 = 0.71) and microcystin (adjusted R2 = 0.84) concentrations over the study period, highlighting their potential for routine monitoring applications. The origin of the monoterpene cyclase required for MIB biosynthesis was putatively linked to a periphytic cyanobacterial mat attached to the concrete drinking water inflow structure. We conclude that shotgun metagenomics can be used to identify microbial agents involved in water quality deterioration and to guide PCR assay selection or design for routine monitoring purposes. Finally, we offer estimates of microbial diversity and metagenomic coverage of our data sets for reference to others wishing to apply shotgun metagenomics to other lacustrine systems.

  3. Treatment of produced water: is a flotation viable process?; Tratamento da agua produzida: a flotacao e um processo viavel?

    Energy Technology Data Exchange (ETDEWEB)

    Santana, Claudia Ramos; Freitas, Andrea Goncalves Bueno de; Silva, Gabriel Francisco da; Paixao, Ana Eleonora Almeida [Universidade Federal de Sergipe (UFS), Aracaju, SE (Brazil); Oliveira, Rosivania da Paixao Silva [Fundacao de Apoio a Pesquisa e Extensao de Sergipe (FAPESE), Aracaju, SE (Brazil)

    2008-07-01

    In petroleum oil wells there comes a situation when most of the oil drilled accompanies a large amount of water. This may be due to the proper conditions of the reservoir or as a consequence of the water injection in the secondary recovery processes from the well. The amount of produced water together with oil can vary to a great extent and it frequently attains to about 50% of the drilled oil. One technique employed for the treatment of industrial effluents, mainly the oily ones which is of great interest is that of flotation. This phenomenon is being extensively used for oil removal from emulsified oils in various areas, such as that of dissolved air flotation (DAF) and the induced air flotation (IAF). The conventional flotation processes consist of the following stages: bubble gas generation (normally air) from the interior of the effluent; collision between the gas bubbles and the suspended oil drops in the water; adhesion of the gas bubbles in the oil drops and ascension of aggregate oil drops/bubbles until the surface, where the oil is removed. This work seeks to contribute for the understanding of the factors which contribute for the selection of the flotation process as one of the methods most viable for the treatment of the produced water. (author)

  4. Integrated use of NMR, petrel and modflow in the modeling of SAGD produced water re-injection

    International Nuclear Information System (INIS)

    Campbell, K.; Phair, C; Alloisio, S; Novotny, M; Raven, S

    2011-01-01

    In the oil industry, steam assisted gravity drainage (SAGD) is a method used to enhance oil recovery in which production water disposal is a challenge. During this process, production water is re-injected into the reservoir and operators have to verify that it will not affect the quality of the surrounding fresh groundwater. This research aimed at determining the flow path and the time that produced water would take to reach an adjacent aquifer. This study was carried out on a horizontal well pair at the Axe Lake Area in northwestern Saskatchewan, using existing site data in Petrel to create a static hydrogeological model which was then exported to Modflow to simulate injection scenarios. This innovative method provided flow path of the re-injected water and time to reach the fresh with advantages over conventional hydrogeological modeling. The innovative workflow presented herein successfully provided useful information to assess the feasibility of the SAGD project and could be used for other projects.

  5. Characterization of OXA-48-like-producing Enterobacteriaceae isolated from river water in Algeria.

    Science.gov (United States)

    Tafoukt, Rima; Touati, Abdelaziz; Leangapichart, Thongpan; Bakour, Sofiane; Rolain, Jean-Marc

    2017-09-01

    The spread of carbapenemase-producing Enterobacteriaceae (CPE) is a significant problem for healthcare worldwide. The prevalence of carbapenem-resistant Enterobacteriaceae (CPE) in water environments in Algeria are unknown. The aim of this study was to screen for the presence of CPE isolates in the Soummam River in Bejaia, Algeria. Isolates of Enterobacteriaceae recovered from twelve samples of river water and showing reduced susceptibility to carbapenems were included in this study. The isolates were identified by matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF MS). Isolates were subjected to antimicrobial susceptibility testing and the modified Carba NP test. Carbapenemase and extended-spectrum β-lactamase (ESBL) determinants were studied by PCR amplification and sequencing. The clonal relatedness between isolates was studied by Multilocus Sequence Typing (MLST) method. A total of 20 carbapenem-resistant Enterobacteriaceae strains were included in this study, identified as Escherichia coli (n = 12), Klebsiella pneumoniae (n = 3), Raoultella ornithinolytica (n = 3), Citrobacter freundii (n = 1) and Citrobacter braakii (n = 1). Carbapenemase genes identified in this study included bla OXA-48 , observed in 17 isolates (9 E. coli, 3 K. pneumoniae, 3 R. ornithinolytica, 1 C. freundii and 1 C. braakii), and bla OXA-244 , a variant of bla OXA-48 , was found in three E. coli isolates. MLST showed that 12 E. coli strains belonged to six different sequence types (ST559, ST38, ST212, ST3541, 1972 and ST2142), and we identified three different STs in K. pneumoniae isolates, including ST133, ST2055, and a new sequence type: ST2192. This study showed the presence of OXA-48-like-producing Enterobacteriaceae in water environments and highlighted the potential role of aquatic environments as reservoirs of clinically relevant antimicrobial-resistant bacteria, with the potential to spread throughout the community. Copyright

  6. Isotopic insights into microbial sulfur cycling in oil reservoirs

    Directory of Open Access Journals (Sweden)

    Christopher G Hubbard

    2014-09-01

    Full Text Available Microbial sulfate reduction in oil reservoirs (biosouring is often associated with secondary oil production where seawater containing high sulfate concentrations (~28 mM is injected into a reservoir to maintain pressure and displace oil. The sulfide generated from biosouring can cause corrosion of infrastructure, health exposure risks, and higher production costs. Isotope monitoring is a promising approach for understanding microbial sulfur cycling in reservoirs, enabling early detection of biosouring, and understanding the impact of souring. Microbial sulfate reduction is known to result in large shifts in the sulfur and oxygen isotope compositions of the residual sulfate, which can be distinguished from other processes that may be occurring in oil reservoirs, such as precipitation of sulfate and sulfide minerals. Key to the success of this method is using the appropriate isotopic fractionation factors for the conditions and processes being monitored. For a set of batch incubation experiments using a mixed microbial culture with crude oil as the electron donor, we measured a sulfur fractionation factor for sulfate reduction of -30‰. We have incorporated this result into a simplified 1D reservoir reactive transport model to highlight how isotopes can help discriminate between biotic and abiotic processes affecting sulfate and sulfide concentrations. Modeling results suggest that monitoring sulfate isotopes can provide an early indication of souring for reservoirs with reactive iron minerals that can remove the produced sulfide, especially when sulfate reduction occurs in the mixing zone between formation waters containing elevated concentrations of volatile fatty acids and injection water containing elevated sulfate. In addition, we examine the role of reservoir thermal, geochemical, hydrological, operational and microbiological conditions in determining microbial souring dynamics and hence the anticipated isotopic signatures.

  7. Environmental evaluation of high-value agricultural produce with diverse water sources: case study from Southern California

    Science.gov (United States)

    Bell, Eric M.; Stokes-Draut, Jennifer R.; Horvath, Arpad

    2018-02-01

    Meeting agricultural demand in the face of a changing climate will be one of the major challenges of the 21st century. California is the single largest agricultural producer in the United States but is prone to extreme hydrologic events, including multi-year droughts. Ventura County is one of California’s most productive growing regions but faces water shortages and deteriorating water quality. The future of California’s agriculture is dependent on our ability to identify and implement alternative irrigation water sources and technologies. Two such alternative water sources are recycled and desalinated water. The proximity of high-value crops in Ventura County to both dense population centers and the Pacific Ocean makes it a prime candidate for alternative water sources. This study uses highly localized spatial and temporal data to assess life-cycle energy use, life-cycle greenhouse gas emissions, operational costs, applied water demand, and on-farm labor requirements for four high-value crops. A complete switch from conventional irrigation with groundwater and surface water to recycled water would increase the life-cycle greenhouse gas emissions associated with strawberry, lemon, celery, and avocado production by approximately 14%, 7%, 59%, and 9%, respectively. Switching from groundwater and surface water to desalinated water would increase life-cycle greenhouse gas emissions by 33%, 210%, 140%, and 270%, respectively. The use of recycled or desalinated water for irrigation is most financially tenable for strawberries due to their relatively high value and close proximity to water treatment facilities. However, changing strawberry packaging has a greater potential impact on life-cycle energy use and greenhouse gas emissions than switching the water source. While this analysis does not consider the impact of water quality on crop yields, previous studies suggest that switching to recycled water could result in significant yield increases due to its lower

  8. Evaluation of excess lifetime cancer risk and radiological hazard in produced water from some flow stations in Delta State, Nigeria

    International Nuclear Information System (INIS)

    Avwiri, G. O.; Esi, E. O.

    2014-01-01

    The radiological effects and excess lifetime cancer risk of produced water collected from seven oil and gas flow stations (fields onshore) of Delta State, Nigeria were estimated using standard analytical. Twenty- one produced water samples from seven flow stations waste pit were collected within the oil fields using standard methods. The radionuclide concentrations in the produced water samples were measured using gamma spectroscopy method. The average values obtained for representative gamma index, annual effective dose equivalent (outdoor), annual effective dose equivalent (indoor) are 0.104mSv/y, 0.0229mSv/y and 0.03276mSv/y respectively when compared with standard of 1.0mSv/y are all below unity. Excess lifetime cancer risk obtained values ranged from 0.0196mSv/y - 0.0434mSv/y with a mean value of 0.0288mSv/y. When compared with the world average standard (0.29 x 10 -3 ), it was observed that the obtained values are higher than the world allowable average. The absorbed dose rate ranged from 4.570mSv/y to 10.088mSv/y with average value of 6.68mSvy-1 was found to be higher than the UNSCEAR 2000 acceptable standard of 1.5mSvy -1 . The results obtained in this study provides a baseline map of radiological effect and excess lifetime cancer risk levels in the Niger Delta environment and will be used as reference information to assess any changes in this studied area. This subject is important in environmental radiological protection, since produced water are widely been discharged in the environment during oil and gas productions.

  9. Potential of nitrate addition to control the activity of sulfate-reducing prokaryotes in high-temperature oil production systems - a comparative study on a nitrate-treated and an untreated system

    DEFF Research Database (Denmark)

    Gittel, Antje; Sørensen, Ketil; Skovhus, Torben L.

    Sulfate-reducing prokaryotes (SRP) cause severe problems like microbial corrosion and reservoir souring in seawater-injected oil production systems. Adding nitrate to the injection water is applied to control SRP activity by favoring the growth of heterotrophic, nitrate-reducing bacteria (h......NRB) and nitrate-reducing, sulfide-oxidizing bacteria (NR-SOB). Microbial diversity, abundance of Bacteria, Archaea and sulfate-reducing prokaryotes (SRP) and the potential activity of SRP were studied in production water samples from a nitrate-treated and an untreated system. The reservoirs and the produced water......) and Desulfotomaculum (system with nitrate). In samples from the untreated site, the presence of active SRP was supported by demonstrating their activity (incubations with 35S-sulfate) and growth in batch cultures at pipeline temperature. No SRP activity was detected at reservoir temperature and in samples from...

  10. Attack of carbonic anhydride and hydrogen sulfide on API class H cement slurries exposed to saline formation waters

    Directory of Open Access Journals (Sweden)

    Márquez, G.

    2011-09-01

    Full Text Available This paper discusses the attack of the major ions (sulfate, chloride, and magnesium and sour gases, present in natural gas (CO2 y SH2, on API class H cement, the type used in gas wells under high pressure and temperature. The effects of these chemical agents on this cement was simulated to study the physicochemical changes due to the action of sour gases and formation water. Cement specimens were immersed in neutral solutions containing fixed concentrations of the major ions inside Parr reactors. These solutions were analysed and XRD analyses were conducted for over two months to identify mineralogical variations from 14 to 60 days. The objective of this research was to determine the effects of the joint attack of major ions and sour gases on cement pastes. The main effects of both gases, jointly or separately, on cement durability were, respectively, the carbonation process and the leaching of some components.

    Se simuló la acción agresiva de los denominados iones fundamentales (sulfato, cloruro y magnesio y los gases agrios presentes en el gas natural (CO2 y H2S sobre un cemento API clase H utilizado en pozos gasíferos a presión y temperatura elevadas, al objeto de observar sus alteraciones fisicoquímicas por la acción combinada de tales gases y las aguas de formación. Se prepararon varias probetas del material cementante para su inmersión en disoluciones neutras, conteniendo los iones fundamentales en concentraciones fijas, dentro de reactores tipo Parr. Se analizaron durante más de dos meses una serie de disoluciones en contacto con el cemento utilizado; así como, mediante DRX, la evolución de la mineralogía de dicho material entre los 14 y los 60 días. Los principales efectos de ambos gases, en conjunto o por separado, sobre la durabilidad del cemento fueron, respectivamente, la formación de carbonato cálcico y la lixiviación de algunos componentes.

  11. Flocculating performance of a bioflocculant produced by Arthrobacter humicola in sewage waste water treatment.

    Science.gov (United States)

    Agunbiade, Mayowa Oladele; Van Heerden, Esta; Pohl, Carolina H; Ashafa, Anofi Tom

    2017-06-12

    The discharge of poorly treated effluents into the environment has far reaching, consequential impacts on human and aquatic life forms. Thus, we evaluated the flocculating efficiency of our test bioflocculant and we report for the first time the ability of the biopolymeric flocculant produced by Arthrobacter humicola in the treatment of sewage wastewater. This strain was isolated from sediment soil sample at Sterkfontein dam in the Eastern Free State province of South Africa. Basic Local Alignment Search Tool (BLAST) analysis of the nucleotide sequence of the 16S rDNA revealed the bacteria to have 99% similarity to Arthrobacter humicola strain R1 and the sequence was deposited in the Gene bank as Arthrobacter humicola with accession number KC816574.1. Flocculating activity was enhanced with the aid of divalent cations, pH 12, at a dosage concentration of 0.8 mg/mL. The purified bioflocculant was heat stable and could retain more than 78% of its flocculating activity after heating at 100 °C for 25 min. Fourier Transform Infrared Spectroscopy analysis demonstrated the presence of hydroxyl and carboxyl moieties as the functional groups. The thermogravimetric analysis was used to monitor the pyrolysis profile of the purified bioflocculant and elemental composition revealed C: O: Na: P: K with 13.90: 41.96: 26.79: 16.61: 0.74 weight percentage respectively. The purified bioflocculant was able to remove chemical oxygen demand, biological oxygen demand, suspended solids, nitrate and turbidity from sewage waste water at efficiencies of 65.7%, 63.5%, 55.7%, 71.4% and 81.3% respectively. The results of this study indicate the possibility of using the bioflocculant produced by Arthrobacter humicola as a potential alternative to synthesized chemical flocculants in sewage waste water treatment and other industrial waste water.

  12. Microbially-Enhanced Redox Solution Reoxidation for Sour Natural Gas Sweetening

    Energy Technology Data Exchange (ETDEWEB)

    Kenneth Brezinsky

    2008-01-15

    The specific objective of this project are to advance the technology and improve the economics of the commercial iron-based chelate processes such as LO-CAT II and SulFerox process utilizing biologically enhanced reoxidation of the redox solutions used in these processes. The project is based on the use of chelated ferric iron as the catalyst for the production of elemental sulfur, and then oxidizing bacteria, such as Thiobacillus Ferrooxidans (ATCC 23270) as an oxidizer. The regeneration of Fe{sup 3+} - chelate is accomplished by the use of these same microbes under mild conditions at 25-30 C and at atmospheric pressure to minimize the chelate degradation process. The pH of the redox solution was observed to be a key process parameter. Other parameters such as temperature, total iron concentration, gas to liquid ratio and bacterial cell densities also influence the overall process. The second part of this project includes experimental data and a kinetic model of microbial H{sub 2}S removal from sour natural gas using thiobacillus species. In the experimental part, a series of experiments were conducted with a commercial chelated iron catalyst at pH ranges from 8.7 to 9.2 using a total iron concentration range from 925 ppm to 1050 ppm in the solution. Regeneration of the solution was carried out by passing air through the solution. Iron oxidizing bacteria were used at cell densities of 2.3 x 10{sup 7}cells/ml for optimum effective performance. In the modeling part, oxidation of Fe{sup 2+} ions by the iron oxidizing bacteria - Thiobacillus Ferrooxidans was studied for application to a continuous stirred tank reactor (CSTR). The factors that can directly affect the oxidation rate such as dilution rate, temperature, and pH were analyzed. The growth of the microorganism was assumed to follow Monod type of growth kinetics. Dilution rate had influence on the rate of oxidation of ferrous iron. Higher dilution rates caused washout of the biomass. The oxidation rate was

  13. Comparison of the disinfection efficacy of chlorine-based products for inactivation of viral indicators and pathogenic bacteria in produce wash water.

    Science.gov (United States)

    Chaidez, Cristobal; Moreno, Maria; Rubio, Werner; Angulo, Miguel; Valdez, Benigno

    2003-09-01

    Outbreaks of pathogenic bacteria infections associated with the consumption of fresh produce has occurred with increased frequency in recent years. This study was undertaken to determine the efficacy of three commonly used disinfectants in packing-houses of Culiacan, Mexico (sodium hypochlorite [NaOCl], trichlor-s-triazinetrione [TST] and thrichlormelamine [TCM]) for inactivation of viral indicators and pathogenic bacteria inoculated onto produce wash water. Each microbial challenge consisted of 2 L of water containing approximately 8 log10 bacterial CFU ml(-1), and 8 log10 viral PFU ml(-1) treated with 100 and 300 mg l(-1) of total chlorine with modified turbidity. Water samples were taken after 2 min of contact with chlorine-based products and assayed for the particular microorganisms. TST and NaOCl were found to effectively reduce for bacterial pathogens and viral indicators 8 log10 and 7 log10, respectively (alpha=0.05). The highest inactivation rate was observed when the turbidity was low and the disinfectant was applied at 300 mg l(-1). TCM did not show effective results when compared with the TST and NaOCl (Pturbidity created by the organic and inorganic material present in the water tanks carried by the fresh produce may affect the efficacy of the chlorine-based products.

  14. Effects of produced waters at oilfield production sites on the Osage Indian Reservation, northeastern Oklahoma

    Science.gov (United States)

    Otton, James K.; Asher-Bolinder, Sigrid; Owen, Douglass E.; Hall, Laurel

    1997-01-01

    The authors conducted limited site surveys in the Wildhorse and Burbank oilfields on the Osage Indian Reservation, northeastern Oklahoma. The purpose was to document salt scarring, erosion, and soil and water salinization, to survey for radioactivity in oilfield equipment, and to determine if trace elements and naturally occurring radioactive materials (NORM) were present in soils affected by oilfield solid waste and produced waters. These surveys were also designed to see if field gamma spectrometry and field soil conductivity measurements were useful in screening for NORM contamination and soil salinity at these sites. Visits to oilfield production sites in the Wildhorse field in June of 1995 and 1996 confirmed the presence of substantial salt scarring, soil salinization, and slight to locally severe erosion. Levels of radioactivity on some oil field equipment, soils, and road surfaces exceed proposed state standards. Radium activities in soils affected by tank sludge and produced waters also locally exceed proposed state standards. Laboratory analyses of samples from two sites show moderate levels of copper, lead, and zinc in brine-affected soils and pipe scale. Several sites showed detectable levels of bromine and iodine, suggesting that these trace elements may be present in sufficient quantity to inhibit plant growth. Surface waters in streams at two sampled sites exceed total dissolved solid limits for drinking waters. At one site in the Wildhorse field, an EM survey showed that saline soils in the upper 6m extend from a surface salt scar downvalley about 150 m. (Photo [95k]: Dead oak trees and partly revegetated salt scar at Site OS95-2 in the Wildhorse field, Osage County, Oklahoma.) In the Burbank field, limited salt scarring and slight erosion occurs in soils at some sites and low to moderate levels of radioactivity were observed in oil field equipment at some sites. The levels of radioactivity and radium observed in some soils and equipment at these

  15. Estimation and correction of produced light from prompt gamma photons on luminescence imaging of water for proton therapy dosimetry

    Science.gov (United States)

    Yabe, Takuya; Komori, Masataka; Toshito, Toshiyuki; Yamaguchi, Mitsutaka; Kawachi, Naoki; Yamamoto, Seiichi

    2018-02-01

    Although the luminescence images of water during proton-beam irradiation using a cooled charge-coupled device camera showed almost the same ranges of proton beams as those measured by an ionization chamber, the depth profiles showed lower Bragg peak intensities than those measured by an ionization chamber. In addition, a broad optical baseline signal was observed in depths that exceed the depth of the Bragg peak. We hypothesize that this broad baseline signal originates from the interaction of proton-induced prompt gamma photons with water. These prompt gamma photons interact with water to form high-energy Compton electrons, which may cause luminescence or Cherenkov emission from depths exceeding the location of the Bragg peak. To clarify this idea, we measured the luminescence images of water during the irradiations of protons in water with minimized parallax errors, and also simulated the produced light by the interactions of prompt gamma photons with water. We corrected the measured depth profiles of the luminescence images by subtracting the simulated distributions of the produced light by the interactions of prompt gamma photons in water. Corrections were also conducted using the estimated depth profiles of the light of the prompt gamma photons, as obtained from the off-beam areas of the luminescence images of water. With these corrections, we successfully obtained depth profiles that have almost identical distributions as the simulated dose distributions for protons. The percentage relative height of the Bragg peak with corrections to that of the simulation data increased to 94% from 80% without correction. Also, the percentage relative offset heights of the deeper part of the Bragg peak with corrections decreased to 0.2%-0.4% from 4% without correction. These results indicate that the luminescence imaging of water has potential for the dose distribution measurements for proton therapy dosimetry.

  16. Effects of chronic produced water exposure on the expression of some immune-related genes of juvenile Atlantic cod

    International Nuclear Information System (INIS)

    Perez Casanova, J.; Hamoutene, D.; Samuelson, S.; Burt, K.; King, T.; Lee, K.

    2010-01-01

    This study assessed the impacts of exposure to processed water produced by offshore oil operators on immune-related genes of juvenile Atlantic cod exposed to processed water for a period of 22 weeks. The study investigated the influence of processed water concentrations on growth parameters; food consumption; plasma cortisol; respiratory burst activity (RB); and mRNA expression. The study showed that the RB of circulating leukocytes was significantly elevated. Significant up-regulation of the mRNA expression of microglobulin, immunoglobulin light chain, and interleukins was observed in some fish. The down-regulation of the interferon stimulated gene was also observed. The study indicated that chronic exposure to significant amounts of processed water causes modulations of the immune system of juvenile Atlantic cod.

  17. Effects of chronic produced water exposure on the expression of some immune-related genes of juvenile Atlantic cod

    Energy Technology Data Exchange (ETDEWEB)

    Perez Casanova, J.; Hamoutene, D.; Samuelson, S.; Burt, K.; King, T. [Fisheries and Oceans Canada, St. John' s, NL (Canada); Lee, K. [Fisheries and Oceans Canada, Dartmouth, NS (Canada)

    2010-07-01

    This study assessed the impacts of exposure to processed water produced by offshore oil operators on immune-related genes of juvenile Atlantic cod exposed to processed water for a period of 22 weeks. The study investigated the influence of processed water concentrations on growth parameters; food consumption; plasma cortisol; respiratory burst activity (RB); and mRNA expression. The study showed that the RB of circulating leukocytes was significantly elevated. Significant up-regulation of the mRNA expression of microglobulin, immunoglobulin light chain, and interleukins was observed in some fish. The down-regulation of the interferon stimulated gene was also observed. The study indicated that chronic exposure to significant amounts of processed water causes modulations of the immune system of juvenile Atlantic cod.

  18. Zeolite Synthesized from Coal Fly Ash Produced by a Gasification Process for Ni2+ Removal from Water

    Directory of Open Access Journals (Sweden)

    Yixin Zhang

    2018-03-01

    Full Text Available There are increasing demands and great potential of coal gasification in China, but there is a lack of studies focused on the disposal and utilization of coal fly ash produced by the gasification process. In this study, a coal fly ash sample derived from a gasifier in Jincheng, China, was utilized as raw material for the synthesis of zeolite by alkali fusion followed by hydrothermal treatments. The effects of operation conditions on the cation exchange capacity (CEC of synthesized zeolite were investigated. The synthesized zeolite with the highest CEC (270.4 meq/100 g, with abundant zeolite X and small amount of zeolite A, was produced by 1.5 h alkali fusion under 550 °C with NaOH/coal fly ash ratio 1.2 g/g followed by 15 h hydrothermal treatment under 90 °C with liquid/solid ratio 5 mL/g and applied in Ni2+ removal from water. The removal rate and the adsorption capacity of Ni2+ from water by the synthesized zeolite were determined at the different pH, contact time, adsorbent dose and initial Ni2+ concentration. The experimental data of adsorption were interpreted in terms of Freundlich and Langmuir equations. The adsorption of Ni2+ by the synthesized zeolite was found to fit sufficient using the Langmuir isotherm. More than 90% of Ni2+ in water could be removed by synthesized zeolite under the proper conditions. We show that the coal fly ash produced by the gasification process has great potential to be used as an alternative and cheap source in the production of adsorbents.

  19. Long-term effects of discharges of produced water the marine environment from petroleum-related activities at Sonda de Campeche, Gulf of México.

    Science.gov (United States)

    Schifter, I; González-Macías, C; Salazar-Coria, L; Sánchez-Reyna, G; González-Lozano, C

    2015-11-01

    Produced water from offshore oil platforms is a major source of oil and related chemicals into the sea. The large volume and high salinity of produced water could pose severe environmental impacts upon inadequate disposal. This study is based on direct field sampling of effluents released into the ocean in the years 2003 and 2013 at the Sonda de Campeche located in the southern part of the Gulf of Mexico. Metals and hydrocarbons were characterized in water, sediments, and fish tissues at the discharge site and compared with those obtained at two reference sites. Chemicals that exceeded risk-based concentrations in the discharge included the metals As, Pb, Cd, and Cr, and a variety of compounds polycyclic aromatic hydrocarbon (PAHs), including naphthalene, fluorenes, and low molecular weight PAHs. The values of low to high molecular weight polycyclic aromatic hydrocarbon (PAHs), and carbon preference index indicate that hydrocarbons in sediments of the discharge zone are originated from the produced water and combustion sources. Fish tissues at the discharge zone and reference site are contaminated with PAHs, dominated by 2- and 3-rings; 4-ring accounted for less than 1% of total PAHs (TPAHs) in 2003, but increased to 7% in 2013. Results suggest that, from 2003 to 2013, discharges of produced water have had a non-negligible impact on ecosystems at a regional level, so the possibility of subtle, cumulative effects from operational discharges should not be ignored.

  20. What do love and jealousy taste like?

    Science.gov (United States)

    Chan, Kai Qin; Tong, Eddie M W; Tan, Deborah H; Koh, Alethea H Q

    2013-12-01

    Metaphorical expressions linking love and jealousy to sweet, sour, and bitter tastes are common in normal language use and suggest that these emotions may influence perceptual taste judgments. Hence, we investigated whether the phenomenological experiences of love and jealousy are embodied in the taste sensations of sweetness, sourness, and bitterness. Studies 1A and 1B validated that these metaphors are widely endorsed. In three subsequent studies, participants induced to feel love rated a variety of tastants (sweet-sour candy, bitter-sweet chocolates, and distilled water) as sweeter than those who were induced to feel jealous, neutral, or happy. However, those induced to feel jealous did not differ from those induced to feel happy or neutral on bitter and sour ratings. These findings imply that emotions can influence basic perceptual judgments, but metaphors that refer to the body do not necessarily influence perceptual judgments the way they imply. We further suggest that future research in metaphoric social cognition and metaphor theory may benefit from investigating how such metaphors could have originated.