Antimicrobial activity of cream incorporated with silver nanoparticles biosynthesized from Withania somnifera

Directory of Open Access Journals (Sweden)

Marslin G

2015-09-01

Full Text Available Gregory Marslin,1 Rajendran K Selvakesavan,1 Gregory Franklin,1 Bruno Sarmento,2,3 Alberto CP Dias11Centre for the Research and Technology of Agro-Environment and Biological Sciences (CITAB-UM, AgroBioPlant Group, Department of Biology, University of Minho, Braga, Portugal; 2Instituto de Engenharia Biomédica (INEB, University of Porto, Porto, Portugal; 3CESPU, Instituto Universitário de Ciências da Saúde, Gandra, PortugalAbstract: We report on the antimicrobial activity of a cream formulation of silver nanoparticles (AgNPs, biosynthesized using Withania somnifera extract. Aqueous extracts of leaves promoted efficient green synthesis of AgNPs compared to fruits and root extracts of W. somnifera. Biosynthesized AgNPs were characterized for their size and shape by physical-chemical techniques such as UV-visible spectroscopy, laser Doppler anemometry, transmission electron microscopy, scanning electron microscopy, atomic force microscopy, X-ray diffraction, and X-ray energy dispersive spectroscopy. After confirming the antimicrobial potential of AgNPs, they were incorporated into a cream. Cream formulations of AgNPs and AgNO3 were prepared and compared for their antimicrobial activity against human pathogens (Staphylococcus aureus, Pseudomonas aeruginosa, Proteus vulgaris, Escherichia coli, and Candida albicans and a plant pathogen (Agrobacterium tumefaciens. Our results show that AgNP creams possess significantly higher antimicrobial activity against the tested organisms.Keywords: Withania somnifera, green synthesis, silver nanoparticles cream, antimicrobial activity

Effects of Withania somnifera (Ashwagandha) and Terminalia arjuna (Arjuna) on physical performance and cardiorespiratory endurance in healthy young adults.

Science.gov (United States)

Sandhu, Jaspal Singh; Shah, Biren; Shenoy, Shweta; Chauhan, Suresh; Lavekar, G S; Padhi, M M

2010-07-01

Several medicinal plants have been described to be beneficial for cardiac ailments in Ayurveda like Ashwagandha and Arjuna. Ashwagandha-categorised as Rasayanas, and described to promote health and longevity and Arjuna primarily for heart ailments. coronary artery disease, heart failure, hypercholesterolemia, anginal pain and can be considered as a useful drug for coronary artery disease, hypertension and ischemic cardiomyopathy. There are no scientific clinical studies showing effect of both these drugs on exercise performance after regular administration when given as supplements The present study was therefore designed and performed to assess the effects of Withania somnifera (Ashwagandha) and Terminalia arjuna (Arjuna) individually and as a combination on maximum velocity, average absolute and relative Power, balance, maximum oxygen consumption (VO2 max) and blood pressure in humans. Forty normal healthy. Subjects (either sex, mean age 20.6 ± 2.5yrs and mean Body Mass Index 21.9 ± 2.2) were recruited after written informed consent was obtained. Institutional Ethics Committee permission was also obtained. Thirty participants were assigned to experimental group of which 10 received standardized root extracts of Withania somnifera, 10 received standardized bark extract of Terminalia arjuna and the rest of the 10 received standardized root extract of Withania somnifera in addition to bark extract of Terminalia arjuna both. Both the drugs were given in the form of capsules (dosage 500mg/day for both the drugs). Ten participants received placebo (capsules filled with flour). All the subjects continued the regimen for 8 weeks. All variables were assessed before and after the course of drug administration Our study showed that Withania somnifera increased velocity, power and VO2 max whereas Terminalia arjuna increased VO2 max and lowered resting systolic blood pressure. When given in combination, the improvement was seen in all parameters except balance and diastolic

Biotechnological interventions in Withania somnifera (L.) Dunal.

Science.gov (United States)

Singh, Pritika; Guleri, Rupam; Singh, Varinder; Kaur, Gurpreet; Kataria, Hardeep; Singh, Baldev; Kaur, Gurcharan; Kaul, Sunil C; Wadhwa, Renu; Pati, Pratap Kumar

2015-01-01

Withania somnifera is one of the most valued plants and is extensively used in Indian, Unani, and African systems of traditional medicine. It possess a wide array of therapeutic properties including anti-arthritic, anti-aging, anti-cancer, anti-inflammatory, immunoregulatory, chemoprotective, cardioprotective, and recovery from neurodegenerative disorders. With the growing realization of benefits and associated challenges in the improvement of W. somnifera, studies on exploration of genetic and chemotypic variations, identification and characterization of important genes, and understanding the secondary metabolites production and their modulation has gained significant momentum. In recent years, several in vitro and in vivo preclinical studies have facilitated the validation of therapeutic potential of the phytochemicals derived from W. somnifera and have provided necessary impetus for gaining deeper insight into the mechanistic aspects involved in the mode of action of these important pharmaceutically active constituents. The present review highlights some of the current developments and future prospects of biotechnological intervention in this important medicinal plant.

Development and optimization of hairy root culture systems in ...

African Journals Online (AJOL)

Transformation of Withania somnifera was carried out by using three Agrobacterium rhizogenes strains (ATCC 15834, R1000 and K599) for hairy root induction. Induction of hairy root was carried out in leaf, petiole and internodal explants. Hairy root induction was successful only in ATCC 15834 and R1000. The highest ...

Histological Evidence of Nephroprotective Effect of Ashwagandha (Withania somnifera Root Extract against Gentamicin Induced Nephrotoxicity in Rats

Directory of Open Access Journals (Sweden)

Sadia Choudhury Shimmi

2014-01-01

Full Text Available Background: Kidney damage can occur due to exposure to nephrotoxic drugs, chemicals, toxins and infectious agents, ultimately leading to renal failure, management of which is a great challenge. So, efforts have been focused on traditional and herbal medicines for the treatment of renal failure. Ashwagandha (Withania somnifera may have free radical scavenging activity and can be used for the prevention and treatment of kidney damage. Objective: To observe the histological evidence of nephroprotective effect of Ashwagandha root against gentamicin induced nephrotoxicity in rats. Materials and Methods: This study was done in the department of Physiology, Sir Salimullah Medical College, Dhaka. A total number of 31 male Wistar albino rats were acclimatized for 14 days. Then, these were divided into two groups, control group consisted of 18 rats (Group A and Ashwagandha pretreated and gentamicin-treated group consisted of 13 rats (Group B. Control group was again subdivided into baseline control and gentamicin-treated control groups (A1 and A2 ─ each group contained 9 rats. All the animals received basal diet for 22 consecutive days. In addition to this, animals of Group A2 received gentamicin subcutaneously (100 mg/kg body weight/day from 15th to 22nd day and animals of Group B received Ashwagandha root extract (500 mg/kg body weight/day orally for 22 consecutive days and gentamicin subcutaneously (100 mg/kg body weight/day from 15th to 22nd day. All the animals were sacrificed on 23rd day. Then kidney samples were collected and histology was done by using standard laboratory procedure. Results: Histological examination of kidney revealed abnormal histological findings in 100% of gentamicin-treated rats. But 92.31% of rats in Ashwagandha pretreated and gentamicin-treated group showed almost normal structure and 7.69% showed mild histological changes. Conclusion: Ashwagandha root may have some nephroprotective effect against gentamicin induced

Withania somnifera targets interleukin-8 and cyclooxygenase-2 in human prostate cancer progression

Directory of Open Access Journals (Sweden)

Anand Setty Balakrishnan

2017-06-01

Conclusion: Our results indicate that inherent metastatic and selective inhibitory potential of W. somnifera against PC. W. somnifera may be a good therapeutic agent in addition to the existing drugs for PC. Further studies with more prostate tissue samples are warranted.

Withania somnifera (Ashwagandha): a Novel Source of L-asparaginase

Institute of Scientific and Technical Information of China (English)

Vishal P. Oza; Shraddha D.Trivedi; Pritesh P.Parmar; R.B.Subramanian

2009-01-01

Different parts of plant species belonging to Solanaceae and Fabaceae families were screened for L-asparaginase enzyme (E.C.3.5.1.1.). Among 34 plant species screened for L-asparaginase enzyme, Withania somnifera L. Was identified as a potential source of the enzyme on the basis of high specific activity of the enzyme. The enzyme was purified and characterized from W. Somnifera, a popular medicinal plant in South East Asia and Southern Europe. Purification was carried out by a combination of protein precipitation with ammonium sulfate as well as Sephadex-gel filtration. The purified enzyme is a homodimer, with a molecular mass of 72±0.5 kDa as estimated by sodium dodecyl sulfate-polyacrylamide gel electrophoresisand size exclusion chromatography. The enzyme has a pH optimum of 8.5 and an optimum temperature of 37℃. The Km value for the enzyme is 6.1×10-2 mmol/L. This is the first report for L-asparaginase from W. Somnifera, a traditionally used Indian medicinal plant.

In Vitro Propagation and Conservation of Withania somnifera (Dunal) L.

Science.gov (United States)

Fatima, Nigar; Ahmad, Naseem; Anis, Mohammad

2016-01-01

Plant tissue culture offers several techniques for rapid clonal propagation, germplasm conservation, regeneration of genetically manipulated superior clones, production of phyto-constituents, and ex vitro conservation of valuable phytodiversity. An improved and efficient micropropagation protocol for Withania somnifera (L.), a drug-producing medicinal plant, using juvenile explants (nodal explants) has been developed. Highest multiplication and subsequent elongation of shoots is observed on MS medium containing BA and NAA. The regenerated microshoots roots best on ½ MS medium containing NAA, established in earthen pots containing garden soil and are maintained in the greenhouse with 95 % survival rate. Genetic uniformity of micropropagated plants is confirmed by PCR-based DNA fingerprinting techniques, viz., RAPD and ISSR. No variation is observed in DNA fingerprinting patterns among the micropropagated plants, which are similar to that of the donor plant illustrating their genetic uniformity.

Efficacy and Safety of Ashwagandha (Withania somnifera Root Extract in Improving Sexual Function in Women: A Pilot Study

Directory of Open Access Journals (Sweden)

Swati Dongre

2015-01-01

Full Text Available Background. Many women experience sexual dysfunction where there are orgasm disorders and sexual difficulties. Ashwagandha (Withania somnifera is a herb known to improve the body’s physical and psychological condition. Objective. The purpose of the study was to determine the efficacy and safety of a high-concentration ashwagandha root extract (HCARE supplementation for improving sexual function in healthy females. Methods. In this pilot study, 50 study subjects were randomized to either (i HCARE-treated group or (ii placebo- (starch- treated group. The subjects consumed either HCARE or placebo capsules of 300mg twice daily for 8 weeks. Sexual function was assessed using two psychometric scales, the Female Sexual Function Index (FSFI Questionnaire and the Female Sexual Distress Scale (FSDS, and by the number of total and successful sexual encounters. Results. The analysis indicates that treatment with HCARE leads to significantly higher improvement, relative to placebo, in the FSFI Total score (p<0.001, FSFI domain score for “arousal” (p<0.001, “lubrication” (p<0.001, “orgasm” (p=0.004, and “satisfaction” (p<0.001, and also FSDS score (p<0.001 and the number of successful sexual encounters (p<0.001 at the end of the treatment. Conclusions. This study demonstrated that oral administration of HCARE may improve sexual function in healthy women. The present study is registered in the Clinical Trial Registry, Government of India, with a number CTRI/2015/07/006045.

The Effect of Chronic Oral Administration of Withania Somnifera Root on Learning and Memory in Diabetic Rats Using Passive Avoidance Test

Directory of Open Access Journals (Sweden)

M. Roghani

2006-07-01

Full Text Available Introduction & Objective: Diabetes mellitus (especially type I is accompanied with disturbances in learning, memory, and cognitive skills in the human society and experimental animals. Considering the potential anti-diabetic effect of the medicinal plant Withania somnifera (ashwagandha and the augmenting effect of its consumption on the memory and mental health, this study was conducted to evaluate the effect of chronic oral administration of ashwagandha root on learning and memory in diabetic rats using passive avoidance test. Materials & Methods: For this purpose, male Wistar diabetic rats were randomly divided into control, ashwagandha-treated control, diabetic, and ashwagandha-treated diabetic groups. Ashwagandha treatment continued for 1 to 2 months. For induction of diabetes, streptozotocin was injected i.p. at a single dose of 60 mg/kg. Serum glucose level was determined before the study and at 4th and 8th weeks after the experiment. In addition, for evaluation of learning and memory, initial latency (IL and step-through latency (STL were determined after 1 and 2 months using passive avoidance test. Results: It was found that one- and two-month administration of ashwagandha root at a weight ratio of 1/15 has not any significant hypoglycemic effect in treated control and diabetic groups. Furthermore, there was a significant increase (p<0.05 in IL in diabetic and ashwagandha-treated diabetic groups after two months compared to control group. In this respect, there was no significant difference between diabetic and ashwagandha-treated diabetic groups. In addition, STL significantly increased in ashwagandha-treated control group after 1 (p<0.01 and 2 (p<0.05 month in comparison to control group. On the other hand, STL significantly decreased (p<0.05 in diabetic group and significantly increased (p<0.05 in ashwagandha-treated diabetic group as compared to control group after two months. Conclusion: In summary, chronic oral administration of

Comparative antistress effect of Vitis vinifera and Withania somnifera using unpredictable chronic mild stress model in rats

Directory of Open Access Journals (Sweden)

Manish Pal Singh

2016-07-01

Full Text Available Introduction: The human society has become complex. However, our physiological responses designed to cope with the ever-increasing adverse situations have not evolved appreciably during the past thousand years. The failure of successful adaptation during stressful situations has resulted in stress-related illnesses. Methods: The objective of the present study was to carry out a comparative assessment of anti-stress effect of Vitis vinifera and Withania somnifera using unpredictable chronic mild stress model in rats. Long-term exposure to multiple stressors can cause depression. The unpredictable chronic administration of various mild stresses, a procedure known as “unpredictable chronic mild stress”, is one of the best-validated rodent models to study stress in animals, for its good etiological and predictive validity. Result: Diazepam, Withania somnifera, Vitis vinifera administration dose dependently reversed the increase in immobility period in stressed rats. In the study of locomotion activity of rats in elevated plus maze apparatus, Stress treated control group rats showed less no of entries in open arm and also less time spent in open arm. Vitis vinifera treated (p<0.0001, Withania somnifera treated (p<0.0001 and Diazepam treated group showed (p<0.0001 no. of entries in open arms which were more than control group and stressed groups. Stressed group produce less average time spent in open arm as compared to treatment groups as Withania somnifera (p<0.05, Vitis vinifera and diazepam. Withania somnifera group showed significant antistress locomotry behaviour in rats. Administration of Vitis vinifera, Withania somnifera and diazepam during stress period restored the ambulatory behaviour of the rats which can be correlated with restoration of plasma corticosterone level. Finally, the results of the present study justified that Withania somnifera, Vitis vinifera and diazepam exhibited significant antistress activity in rats.

In Vitro Propagation of Withania somnifera (L.) Dunal.

Science.gov (United States)

Singh, Pritika; Guleri, Rupam; Pati, Pratap Kumar

2016-01-01

Withania somnifera (L.) Dunal known as Ashwagandha is commonly used in traditional Indian medicine system. It possesses immense therapeutic value against a large number of ailments such as mental diseases, asthma, inflammation, arthritis, rheumatism, tuberculosis, and a variety of other diseases including cancer. The therapeutic potential of W. somnifera is due to the presence of secondary metabolites mainly, tropane alkaloids and withanolides (steroidal lactones). The growing realization of commercial value of the plant has initiated a new demand for in vitro propagation of elite chemotypes of Withania. Micropropagation which is an important tool for rapid multiplication requires optimization of number of factors such as nutrient medium, status of medium (solid and liquid), type of explant, and plant growth regulators. Similarly, an efficient and reproducible in vitro regeneration system which is a prerequisite for the development of genetic transformation protocol requires precise manipulation of various intrinsic and extrinsic factors.

Bioremediation of petroleum contaminated soil to combat toxicity on Withania somnifera through seed priming with biosurfactant producing plant growth promoting rhizobacteria.

Science.gov (United States)

Das, Amar Jyoti; Kumar, Rajesh

2016-06-01

Soil contaminated by Petroleum oil cannot be utilized for agricultural purposes due to hydrocarbon toxicity. Oil contaminated soil induces toxicity affecting germination, growth and productivity. Several technologies have been proposed for bioremediation of oil contaminated sites, but remediation through biosurfactant producing plant growth promontory rhizobacteria (PGPR) is considered to be most promising methods. In the present study the efficacy of seed priming on growth and pigment of Withania somnifera under petroleum toxicity is explored. Seeds of W. somnifera were primed with biosurfactant producing Pseudomonas sp. AJ15 with plant growth promoting traits having potentiality to utilized petroleum as carbon source. Results indicates that plant arose from priming seeds under various petroleum concentration expressed high values for all the parameters studied namely germination, shoot length, root length, fresh and dry weight and pigments (chlorophyll and carotenoid) as compared to non primed seed. Hence, the present study signifies that petroleum degrarding biosurfactant producing PGPR could be further used for management and detoxification of petroleum contaminated soils for growing economically important crops. Copyright © 2016. Published by Elsevier Ltd.

Effect of traditional methods and gamma irradiation on microbial load, quality and sensory characteristics of Licorice Roots Powder (Glycyrrhiza globra L.)

International Nuclear Information System (INIS)

Al-Bachir, M.; Al-Adawi, M.

2013-04-01

To determine the effect of gamma irradiation and heat treatment on microbial load of licorice root powder, extract rate from root powder, and the physical, chemical and sensory characteristics of its extract. Powder of licorice roots were exposed to heat treatments (hot air-dried and steam), and to 10 kGy of gamma irradiation. Microbial load on powder, and organic dissolved solids, total carbohydrates, reduced carbohydrates, Glycyrrhezinic, ash, mineral ions (Ca++ and K+, Na, Mg), pH and EC values, color, and sensory properties of the extracted were evaluated after 0, 6, and 12 months of storage. Results indicated that total microbial count of licorice roots powder (control sample) were relatively high, and included coliform, E. coli, and Klabsala spp. The results indicated that 10 kGy of gamma irradiation reduced the total count by 4 logs. While, heat treatment (hot air-dried, and steamed) reduced the total count by 1 and 2 logs respectively. No effect was observed in physical, and chemical characteristics in the extract of licorice roots due to irradiation. While, there were an effect of heat treatment on most of measured physical, and chemical characteristics of the extract of licorice roots. However, Sensory evaluation indicated that no significant differences were found between solution produced from irradiated, heat treated, and control samples in color, flavor, texture, or taste (author).

Effect of Administration of Withania somnifera on Some Hematological and Immunological Profile of Broiler Chicks

Directory of Open Access Journals (Sweden)

Muhammad Mushtaq*, F. R. Durrani, N. Imtiaz, Umer Sadique1, A. Hafeez, S. Akhtar2 and S. Ahmad3

2012-01-01

Full Text Available This study was conducted to assess the performance of broiler chickens based on some hematological and immunological profile, upon inclusion of aqueous extract of Withania somnifera (W. somnifera in their drinking water. For this purpose, 240 a-day-old broiler chicks were purchased from a local hatchery and divided into four groups i.e. WST-0, WST-I, WST-II and WST-III. Group WST-0 was kept as control, while chicks in group WST-I, WST-II and WST-III were offered in their drinking water with an extract of W. somnifera at 10, 20 and 30g/L for 35 days, starting from day 1 of age. Feed intake and body weight were recorded on regular basis and hematological and immunological profile of the birds was analyzed at the end of experiment. Administration of W. somnifera extract resulted in significantly higher feed intake and body weight of birds in all treated groups. An increase in the values of Hb, PCV and TLC was noted in the treatment groups. A non significant difference was noted in the counts of neutrophils, lymphocytes, eosinophils and monocytes in all treatment groups as compared to control. Antibodies titers against IB and IBD were significantly higher in all treatment groups as compare to the values shown by the chicks in control group. Findings of this study indicated that administration of W. somnifera extract to broiler chicks improve their feed intake, body weight gain, hematological profile and immunological status.

Preventive role of Withania somnifera on hyperlipidemia and cardiac ...

African Journals Online (AJOL)

and cardiac oxidative stress in streptozotocin induced type. 2 diabetic rats ... Abstract. Purpose: The present study was intended to investigate the preventive role ofWithania somnifera (WS) ..... The authors declare that this work was done by.

Overexpression of WsSGTL1 Gene of Withania somnifera Enhances Salt Tolerance, Heat Tolerance and Cold Acclimation Ability in Transgenic Arabidopsis Plants

Science.gov (United States)

Mishra, Manoj K.; Chaturvedi, Pankaj; Singh, Ruchi; Singh, Gaurav; Sharma, Lokendra K.; Pandey, Vibha; Kumari, Nishi; Misra, Pratibha

2013-01-01

Background Sterol glycosyltrnasferases (SGT) are enzymes that glycosylate sterols which play important role in plant adaptation to stress and are medicinally important in plants like Withania somnifera. The present study aims to find the role of WsSGTL1 which is a sterol glycosyltransferase from W. somnifera, in plant’s adaptation to abiotic stress. Methodology The WsSGTL1 gene was transformed in Arabidopsis thaliana through Agrobacterium mediated transformation, using the binary vector pBI121, by floral dip method. The phenotypic and physiological parameters like germination, root length, shoot weight, relative electrolyte conductivity, MDA content, SOD levels, relative electrolyte leakage and chlorophyll measurements were compared between transgenic and wild type Arabidopsis plants under different abiotic stresses - salt, heat and cold. Biochemical analysis was done by HPLC-TLC and radiolabelled enzyme assay. The promoter of the WsSGTL1 gene was cloned by using Genome Walker kit (Clontech, USA) and the 3D structures were predicted by using Discovery Studio Ver. 2.5. Results The WsSGTL1 transgenic plants were confirmed to be single copy by Southern and homozygous by segregation analysis. As compared to WT, the transgenic plants showed better germination, salt tolerance, heat and cold tolerance. The level of the transgene WsSGTL1 was elevated in heat, cold and salt stress along with other marker genes such as HSP70, HSP90, RD29, SOS3 and LEA4-5. Biochemical analysis showed the formation of sterol glycosides and increase in enzyme activity. When the promoter of WsSGTL1 gene was cloned from W. somnifera and sequenced, it contained stress responsive elements. Bioinformatics analysis of the 3D structure of the WsSGTL1 protein showed functional similarity with sterol glycosyltransferase AtSGT of A. thaliana. Conclusions Transformation of WsSGTL1 gene in A. thaliana conferred abiotic stress tolerance. The promoter of the gene in W.somnifera was found to have stress

Extracts from Aloe ferox and Withania somnifera inhibit Candida ...

African Journals Online (AJOL)

SERVER

2008-01-04

Jan 4, 2008 ... Herbal medicines play a vital role in the treatment of sexually transmitted infections (STIs), especially in the remote areas of South Africa where clinics and hospitals are sparsely located. Aloe ferox and. Withania somnifera are among the southern African plants commonly used for the treatment of (STIs).

Comparing the cytotoxic potential of Withania somnifera water and ...

African Journals Online (AJOL)

The plant Withania somnifera (Linn.) (Solanacea) is a well-known herbal medicine used in many parts of the world. It has anti-inflammatory, antioxidant, and antitumor as well as neural protective properties. It seems as if the two most active withanolide components, namely withaferin A and withanolide D, found in methanol ...

Preventive role of Withania somnifera on hyperlipidemia and cardiac ...

African Journals Online (AJOL)

Purpose: The present study was intended to investigate the preventive role of Withania somnifera (WS) on hyperlipidemia and oxidative stress in the heart of streptozotocin (STZ)-induced type 2 diabetic rats. Methods: Single intraperitoneal injection of STZ (100 mg/kg) was given to 2 days rat pups to induce type 2 diabetes ...

A WRKY transcription factor from Withania somnifera regulates triterpenoid withanolide accumulation and biotic stress tolerance through modulation of phytosterol and defense pathways.

Science.gov (United States)

Singh, Anup Kumar; Kumar, Sarma Rajeev; Dwivedi, Varun; Rai, Avanish; Pal, Shaifali; Shasany, Ajit K; Nagegowda, Dinesh A

2017-08-01

Withania somnifera produces pharmacologically important triterpenoid withanolides that are derived via phytosterol pathway; however, their biosynthesis and regulation remain to be elucidated. A jasmonate- and salicin-inducible WRKY transcription factor from W. somnifera (WsWRKY1) exhibiting correlation with withaferin A accumulation was functionally characterized employing virus-induced gene silencing and overexpression studies combined with transcript and metabolite analyses, and chromatin immunoprecipitation assay. WsWRKY1 silencing resulted in stunted plant growth, reduced transcripts of phytosterol pathway genes with corresponding reduction in phytosterols and withanolides in W. somnifera. Its overexpression elevated the biosynthesis of triterpenoids in W. somnifera (phytosterols and withanolides), as well as tobacco and tomato (phytosterols). Moreover, WsWRKY1 binds to W-box sequences in promoters of W. somnifera genes encoding squalene synthase and squalene epoxidase, indicating its direct regulation of triterpenoid pathway. Furthermore, while WsWRKY1 silencing in W. somnifera compromised the tolerance to bacterial growth, fungal infection, and insect feeding, its overexpression in tobacco led to improved biotic stress tolerance. Together these findings demonstrate that WsWRKY1 has a positive regulatory role on phytosterol and withanolides biosynthesis, and defense against biotic stress, highlighting its importance as a metabolic engineering tool for simultaneous improvement of triterpenoid biosynthesis and plant defense. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Effect of Administration of Withania somnifera on Some Hematological and Immunological Profile of Broiler Chicks

OpenAIRE

Muhammad Mushtaq*, F. R. Durrani, N. Imtiaz, Umer Sadique1, A. Hafeez, S. Akhtar2 and S. Ahmad3

2012-01-01

This study was conducted to assess the performance of broiler chickens based on some hematological and immunological profile, upon inclusion of aqueous extract of Withania somnifera (W. somnifera) in their drinking water. For this purpose, 240 a-day-old broiler chicks were purchased from a local hatchery and divided into four groups i.e. WST-0, WST-I, WST-II and WST-III. Group WST-0 was kept as control, while chicks in group WST-I, WST-II and WST-III were offered in their drinking water with ...

Anti-inflammatory, antiallodynic effects and quantitative analysis of gallic acid in spray dried powders from Phyllanthus niruri leaves, stems, roots and whole plant

Directory of Open Access Journals (Sweden)

Angélica G. Couto

2012-11-01

Full Text Available The anti-inflammatory and antiallodynic effects of spray dried powders starting from leaves, stems, roots, the mixture of leaves and stems, as well as the whole plant aqueous solutions of Phyllanthus niruri L., Phyllanthaceae, were assessed. Gallic acid, used as chemical marker, was quantified by HPLC in the spray dried powders. Carrageenan-induced inflammatory and allodynic responses in the mouse paw were used as pharmacological models. Quantitative and qualitative differences among chemical composition of different herb parts were observed. The oral administration of leaves or leaves plus stems spray dried powders (100 mg/kg significantly inhibited the carrageenan-induced allodynic effect (42±5 and 54±3%, respectively. Additionally, the spray dried powders of leaves significantly reduced carrageenan-induced paw oedema (35±6%. The spray dried powders of roots, stems, or the mixture of leaves, stems and roots (100 mg/kg, p.o. did not exhibit antiallodynic or antioedematogenic effect in the same model. In conclusion, differences in the chemical composition of spray dried powders from P. niruri are reflected in their in vivo pharmacological actions. Despite of a direct relationship of anti-inflammatory and antiallodynic effects with the gallic acid content had been observed, especially in the spray dried powders of leaves, the use of spray dried powders of leaves plus stems showed to be more effective, suggesting a synergic effect between their constituents.

Anti-inflammatory, antiallodynic effects and quantitative analysis of gallic acid in spray dried powders from Phyllanthus niruri leaves, stems, roots and whole plant

Directory of Open Access Journals (Sweden)

Angélica G. Couto

2013-02-01

Full Text Available The anti-inflammatory and antiallodynic effects of spray dried powders starting from leaves, stems, roots, the mixture of leaves and stems, as well as the whole plant aqueous solutions of Phyllanthus niruri L., Phyllanthaceae, were assessed. Gallic acid, used as chemical marker, was quantified by HPLC in the spray dried powders. Carrageenan-induced inflammatory and allodynic responses in the mouse paw were used as pharmacological models. Quantitative and qualitative differences among chemical composition of different herb parts were observed. The oral administration of leaves or leaves plus stems spray dried powders (100 mg/kg significantly inhibited the carrageenan-induced allodynic effect (42±5 and 54±3%, respectively. Additionally, the spray dried powders of leaves significantly reduced carrageenan-induced paw oedema (35±6%. The spray dried powders of roots, stems, or the mixture of leaves, stems and roots (100 mg/kg, p.o. did not exhibit antiallodynic or antioedematogenic effect in the same model. In conclusion, differences in the chemical composition of spray dried powders from P. niruri are reflected in their in vivo pharmacological actions. Despite of a direct relationship of anti-inflammatory and antiallodynic effects with the gallic acid content had been observed, especially in the spray dried powders of leaves, the use of spray dried powders of leaves plus stems showed to be more effective, suggesting a synergic effect between their constituents.

Effect of Withania somnifera Dunal Root Extract on Behavioral Despair Model in Mice: a Possible Role for Nitric Oxide

Directory of Open Access Journals (Sweden)

Mahshid Attari

2016-04-01

Full Text Available Withania somnifera (WS possess anti-inflammatory and antioxidant properties. WS preparations have a potential therapeutic role in the central nervous system (CNS related disorders in animal models. In this study, the possible protective effect of acute aqueous WS root extract on behavioral despair was explored and compared with fluoxetine, an antidepressant with selective serotonin (5-HT reuptake inhibitor activity (SSRI. Further, the probable involvement of nitric oxide (NO determined to measure immobility time in forced swimming test (FST and tail suspension test (TST in male mice. Immediately after assessment of locomotor activity, the immobility time was evaluated. WS was administered intraperitoneally (200, 400 mg/kg; i.p. 60 min before the behavioral tests. To assess the involvement of NO in the possible protective effect of WS, a non-specific NO synthase inhibitor, NG-L-arginine methyl ester (L-NAME, 10 mg/kg, i.p. was administered 30 min before the extract administration (400 mg/kg, i.p., 90 min before the tests. Acute WS extract (200, 400 mg/kg, i.p. dose-dependently decreased the immobility time in FST, P<0.05, P<0.001, respectively and 400 mg/kg proved the most effective dose and this dose was comparable to fluoxetine (20 mg/kg, i.p. WS (400 mg/kg, i.p. also lowered the immobility measure in TST (P<0.05. However, these effects were not related to change in locomotor activity. Moreover, L-NAME (10 mg/kg, i.p. did not influence the effect of the extract on the behavioral tests. As a consequence, the immobility time was virtually constant between the group received the extract (400 mg/kg alone, and the group received L-NAME (10 mg/kg before the extract. It is probable that NO does not mediate this beneficial effect, and WS may affect other neurochemical systems and pathways.

Effect of Withania somnifera leaf extract on the dietary supplementation in transgenic Drosophila model of Parkinson’s disease

Directory of Open Access Journals (Sweden)

YASIR HASAN SIDDIQUE

2015-09-01

Full Text Available The role of Withania somnifera L. leaf extract was studied on the transgenic Drosophila model flies expressing normal human alpha synuclein (h-αS in the neurons. The leaf extract was prepared in acetone and was subjected to GC-MS analysis. W. somnifera extract at final concentration of 0.25, 0.50 and 1.0 µL/mL was mixed with the diet and the flies were allowed to feed for 24 days. The effect of extract was studied on the climbing ability, lipid peroxidation and protein carbonyl content in the brains of transgenic Drosophila. The exposure of extract to PD model flies did not show any significant delay in the loss of climbing ability nor reduced the oxidative stress in the brains of transgenic Drosophila as compared to untreated PD model flies. The results suggest that W. somnifera leaf extract is not potent in reducing the PD symptoms in transgenic Drosophila model of Parkinson’s disease.

Root exudates and leaf leachates of 19 medicinal plants of pakistan exhibit allelopathic potential

International Nuclear Information System (INIS)

Syed, S.; Ahmed, Z.I.; Razzaq, A.

2014-01-01

Laboratory experiments were conducted to evaluate the allelopathic potential of root exudates and leaf leachates of 19 medicinal plants commonly used in Pakistan by plant box and sandwich methods, respectively. In sandwich method, lettuce seedlings were grown with the dry leaf leachates of the selected plant species in a growing media at the rate of 5, 10 and 50 mg dish-1 in a completely randomized design with three replications. Their effects on hypocotyl and radicle growth of the lettuce were recorded as a percentage of untreated control. Data was subjected for analysis of variance and treatment means were compared by Tukey's HSD test at p<0.05. Results indicated that allelopathic effects of the leaf leachates of all selected plant species on the hypocotyl and radicle elongations of the lettuce varied significantly in all concentrations used in experiments. The hypocotyl growth of the lettuce seedlings was affected from promotion (6.71% inhibition) caused by Phlaris minor to inhibition (78.40%) by Withania somnifera. Both species suppressed the radicle length from 33.69-93.30%. Leachates of W. somnifera and Sarcococca saligna exhibited strong inhibitory results in a concentration dependant manner. After the growth period of 50 days, root exudates of S. saligna appeared most detrimental (78.00% inhibition) to radicle growth of the lettuce seedling followed by W. somnifera (75.00%) when tested by plant box method. The results presented can be utilized as benchmark information for further joint research on the elucidation of chemicals involved in the allelopathy in nature and in the development of new and potent bioherbicides to combat environmental risk. (author)

Ashwagandha (Withania somnifera reverses β-amyloid1-42 induced toxicity in human neuronal cells: implications in HIV-associated neurocognitive disorders (HAND.

Directory of Open Access Journals (Sweden)

Kesava Rao Venkata Kurapati

Full Text Available Alzheimer's disease (AD is characterized by progressive dysfunction of memory and higher cognitive functions with abnormal accumulation of extracellular amyloid plaques and intracellular neurofibrillary tangles throughout cortical and limbic brain regions. At present no curative treatment is available, and research focuses on drugs for slowing disease progression or providing prophylaxis. Withania somnifera (WS also known as 'ashwagandha' is used widely in Ayurvedic medicine as a nerve tonic and memory enhancer. However, there is a paucity of data on the potential neuroprotective effects of W.somnifera against β-Amyloid (1-42-induced neuropathogenesis. In the present study, we have tested the neuroprotective effects of methanol:Chloroform (3:1 extract of ashwagandha against β-amyloid induced toxicity and HIV-1Ba-L (clade B infection using a human neuronal SK-N-MC cell line. Our results showed that β-amyloid induced cytotoxic effects in SK-N-MC cells as shown by decreased cell growth when tested individually. Also, confocal microscopic analysis showed decreased spine density, loss of spines and decreased dendrite diameter, total dendrite and spine area in clade B infected SK-N-MC cells compared to uninfected cells. However, when ashwagandha was added to β-amyloid treated and HIV-1 infected samples, the toxic effects were neutralized. Further, the MTT cell viability assays and the peroxisome proliferator-activated receptor-γ (PPARγ levels supported these observations indicating the neuroprotective effect of WS root extract against β-amyloid and HIV-1Ba-L (clade B induced neuro-pathogenesis.

Withania somnifera attenuates acid production, acid tolerance and extra-cellular polysaccharide formation of Streptococcus mutans biofilms.

Science.gov (United States)

Pandit, Santosh; Song, Kwang-Yeob; Jeon, Jae-Gyu

2014-01-01

Withania somnifera (Ashwagandha) is a plant of the Solanaceae family. It has been widely used as a remedy for a variety of ailments in India and Nepal. The plant has also been used as a controlling agent for dental diseases. The aim of the present study was to evaluate the activity of the methanol extract of W. somnifera against the physiological ability of cariogenic biofilms and to identify the components of the extract. To determine the activity of the extract, assays for sucrose-dependent bacterial adherence, glycolytic acid production, acid tolerance, and extracellular polysaccharide formation were performed using Streptococcus mutans biofilms. The viability change of S. mutans biofilms cells was also determined. A phytochemical analysis of the extract was performed using TLC and LC/MS/MS. The extract showed inhibitory effects on sucrose-dependent bacterial adherence (≥ 100 μg/ml), glycolytic acid production (≥ 300 μg/ml), acid tolerance (≥ 300 μg/ml), and extracellular polysaccharide formation (≥ 300 μg/ml) of S. mutans biofilms. However, the extract did not alter the viability of S. mutans biofilms cells in all concentrations tested. Based on the phytochemical analysis, the activity of the extract may be related to the presence of alkaloids, anthrones, coumarines, anthraquinones, terpenoids, flavonoids, and steroid lactones (withanolide A, withaferin A, withanolide B, withanoside IV, and 12-deoxy withastramonolide). These data indicate that W. somnifera may be a potential agent for restraining the physiological ability of cariogenic biofilms.

Triethylene glycol, an active component of Ashwagandha (Withania somnifera) leaves, is responsible for sleep induction.

Science.gov (United States)

Kaushik, Mahesh K; Kaul, Sunil C; Wadhwa, Renu; Yanagisawa, Masashi; Urade, Yoshihiro

2017-01-01

Insomnia is the most common sleep complaint which occurs due to difficulty in falling asleep or maintaining it. Most of currently available drugs for insomnia develop dependency and/or adverse effects. Hence natural therapies could be an alternative choice of treatment for insomnia. The root or whole plant extract of Ashwagandha (Withania somnifera) has been used to induce sleep in Indian system of traditional home medicine, Ayurveda. However, its active somnogenic components remain unidentified. We investigated the effect of various components of Ashwagandha leaf on sleep regulation by oral administration in mice. We found that the alcoholic extract that contained high amount of active withanolides was ineffective to induce sleep in mice. However, the water extract which contain triethylene glycol as a major component induced significant amount of non-rapid eye movement sleep with slight change in rapid eye movement sleep. Commercially available triethylene glycol also increased non-rapid eye movement sleep in mice in a dose-dependent (10-30 mg/mouse) manner. These results clearly demonstrated that triethylene glycol is an active sleep-inducing component of Ashwagandha leaves and could potentially be useful for insomnia therapy.

Triethylene glycol, an active component of Ashwagandha (Withania somnifera leaves, is responsible for sleep induction.

Directory of Open Access Journals (Sweden)

Mahesh K Kaushik

Full Text Available Insomnia is the most common sleep complaint which occurs due to difficulty in falling asleep or maintaining it. Most of currently available drugs for insomnia develop dependency and/or adverse effects. Hence natural therapies could be an alternative choice of treatment for insomnia. The root or whole plant extract of Ashwagandha (Withania somnifera has been used to induce sleep in Indian system of traditional home medicine, Ayurveda. However, its active somnogenic components remain unidentified. We investigated the effect of various components of Ashwagandha leaf on sleep regulation by oral administration in mice. We found that the alcoholic extract that contained high amount of active withanolides was ineffective to induce sleep in mice. However, the water extract which contain triethylene glycol as a major component induced significant amount of non-rapid eye movement sleep with slight change in rapid eye movement sleep. Commercially available triethylene glycol also increased non-rapid eye movement sleep in mice in a dose-dependent (10-30 mg/mouse manner. These results clearly demonstrated that triethylene glycol is an active sleep-inducing component of Ashwagandha leaves and could potentially be useful for insomnia therapy.

Quantitative determination of multi markers in five varieties of Withania somnifera using ultra-high performance liquid chromatography with hybrid triple quadrupole linear ion trap mass spectrometer combined with multivariate analysis: Application to pharmaceutical dosage forms.

Science.gov (United States)

Chandra, Preeti; Kannujia, Rekha; Saxena, Ankita; Srivastava, Mukesh; Bahadur, Lal; Pal, Mahesh; Singh, Bhim Pratap; Kumar Ojha, Sanjeev; Kumar, Brijesh

2016-09-10

An ultra-high performance liquid chromatography electrospray ionization tandem mass spectrometry method has been developed and validated for simultaneous quantification of six major bioactive compounds in five varieties of Withania somnifera in various plant parts (leaf, stem and root). The analysis was accomplished on Waters ACQUITY UPLC BEH C18 column with linear gradient elution of water/formic acid (0.1%) and acetonitrile at a flow rate of 0.3mLmin(-1). The proposed method was validated with acceptable linearity (r(2), 0.9989-0.9998), precision (RSD, 0.16-2.01%), stability (RSD, 1.04-1.62%) and recovery (RSD ≤2.45%), under optimum conditions. The method was also successfully applied for the simultaneous determination of six marker compounds in twenty-six marketed formulations. Hierarchical cluster analysis and principal component analysis were applied to discriminate these twenty-six batches based on characteristics of the bioactive compounds. The results indicated that this method is advance, rapid, sensitive and suitable to reveal the quality of Withania somnifera and also capable of performing quality evaluation of polyherbal formulations having similar markers/raw herbs. Copyright © 2016 Elsevier B.V. All rights reserved.

Efficacy of Ashwagandha (Withania somnifera [L.] Dunal) in improving cardiorespiratory endurance in healthy athletic adults.

Science.gov (United States)

Choudhary, Bakhtiar; Shetty, A; Langade, Deepak G

2015-01-01

Ashwagandha (Withania somnifera [L.] Dunal) has been traditionally used for various actions ranging from vitalizer, improve endurance and stamina, promote longevity, improve immunity, and male and female fertility. However, clinical studies are needed to prove the clinical efficacy of this herb, especially in cardiovascular endurance and physical performance. This prospective, double-blind, randomized, and placebo-controlled study evaluated the efficacy of Ashwagandha roots extract in enhancing cardiorespiratory endurance and improving the quality of life (QOL) in 50 healthy male/female athletic adults. Cardiorespiratory endurance was assessed by measuring the oxygen consumption at peak physical exertion (VO2 max) levels during a 20 m shuttle run test. The World Health Organization self-reported QOL questionnaire (physical health, psychological health, social relationships, and environmental factors) was used to assess the QOL. Student's t-test was used to compare the differences in a mean and change from baseline VO2 max levels, whereas Wilcoxon signed-rank test was used to assess changes in QOL scores from baseline in the two groups. There was a greater increase from baseline (P < 0.0001) in the mean VO2 max with KSM-66 Ashwagandha (n = 24) compared to placebo (n = 25) at 8 weeks (4.91 and 1.42, respectively) and at 12 weeks (5.67 and 1.86 respectively). The QOL scores for all subdomains significantly improved to a greater extent in the Ashwagandha group at 12 weeks compared to placebo (P < 0.05). The findings suggest that Ashwagandha root extract enhances the cardiorespiratory endurance and improves QOL in healthy athletic adults.

RNAi and Homologous Over-Expression Based Functional Approaches Reveal Triterpenoid Synthase Gene-Cycloartenol Synthase Is Involved in Downstream Withanolide Biosynthesis in Withania somnifera.

Directory of Open Access Journals (Sweden)

Smrati Mishra

Full Text Available Withania somnifera Dunal, is one of the most commonly used medicinal plant in Ayurvedic and indigenous medicine traditionally owing to its therapeutic potential, because of major chemical constituents, withanolides. Withanolide biosynthesis requires the activities of several enzymes in vivo. Cycloartenol synthase (CAS is an important enzyme in the withanolide biosynthetic pathway, catalyzing cyclization of 2, 3 oxidosqualene into cycloartenol. In the present study, we have cloned full-length WsCAS from Withania somnifera by homology-based PCR method. For gene function investigation, we constructed three RNAi gene-silencing constructs in backbone of RNAi vector pGSA and a full-length over-expression construct. These constructs were transformed in Agrobacterium strain GV3101 for plant transformation in W. somnifera. Molecular and metabolite analysis was performed in putative Withania transformants. The PCR and Southern blot results showed the genomic integration of these RNAi and overexpression construct(s in Withania genome. The qRT-PCR analysis showed that the expression of WsCAS gene was considerably downregulated in stable transgenic silenced Withania lines compared with the non-transformed control and HPLC analysis showed that withanolide content was greatly reduced in silenced lines. Transgenic plants over expressing CAS gene displayed enhanced level of CAS transcript and withanolide content compared to non-transformed controls. This work is the first full proof report of functional validation of any metabolic pathway gene in W. somnifera at whole plant level as per our knowledge and it will be further useful to understand the regulatory role of different genes involved in the biosynthesis of withanolides.

Ultrastructure of Withania Somnifera (L.) Dunal pollen grains

International Nuclear Information System (INIS)

Alwadie, H.M.

2002-01-01

Light, scanning and transmission electron microscopy were used to study the morphology and ultrastructure of Withania Somnifera (L.) Dunall pollen grains. Light microscopic examination revealed that the pollen grains are tri- or tetrazonocoplate grains, approximately as long as broad, measuring 29-um. Scanning electron microscopic observation showed that surface sculpturing of the pollen is scarbate-granulate. Ultrathin sections as examined by transmission electron microscope showed that the pollen contained numerous starch grains, lipid droplets, endoplasmic reticulum and vesicles of dictyosomes. Two layers of the pollen wall were also distinguished, the outer wall (exine) divided into ektexine and endexine as well as the inner layer (intine). The nutritive values of Withania pollen are discussed. The importance of studying the ultrastructure of pollen grains as a new tool in palynology is also discussed. (author)

A randomized, double blind placebo controlled study of efficacy and tolerability of Withaina somnifera extracts in knee joint pain

Directory of Open Access Journals (Sweden)

G.S.H. Ramakanth

2016-07-01

Conclusions: Both the doses of an aqueous extract of W. somnifera produced significant reduction in outcome variables, with the 250 mg group showing significantly better response. In addition, the therapeutic response appears to be dose-dependent and free of any significant GI disturbances.

Molecular Phylogenetic Screening of Withania somnifera Relative From Indonesia Based on Internal Transcribed Spacer Region

Directory of Open Access Journals (Sweden)

Topik Hidayat

2016-04-01

Full Text Available Withania somnifera (family Solanaceae, known commonly as Ashwaganda, is one of the important medicinal plants, and recent studies reported that Withanone, one of the chemical components in this plant, has ability to kill cancer cell. Because of endemic state of this plant to South Asia, exploring plant species under the same family which grow well in Indonesia has been of interest. The purpose of this study was to screen the Indonesian plant which has strong phylogenetic relationship with Ashwaganda. Thus, phylogenetic analysis using DNA sequences of internal transcribed spacer (ITS region was conducted. Thus, 19 species of Solanaceae and two species of Convolvulaceae as outgroup were examined. Five ITS regions of Ashwaganda retrieved from GenBank were included in the phylogenetic analysis. Parsimony analysis showed that Indonesia Solanaceae comprises seven groups which is consistent with the global Solanaceae relationship as previously reported. Furthermore, our study revealed that two species, Physalis angulata and Physalis peruviana, are relative to W. somnifera. Morphologically, they share characters of flower and fruit. This result indicated that these two species are potential to have similar chemical properties as Ashwaganda, thus we can have new variants of Withanone originated from Indonesia with similar effect.

Pharmacognostic Study of Argyreia pilosa Wight & Arn. Root

Directory of Open Access Journals (Sweden)

prasanth DSNBK

2017-12-01

Full Text Available Background: Ethnomedicinally, the plant Argyreia pilosa Wight & Arn. (Convolvulaceae has long been utilized in various disorders in the conventional system; most significantly it is utilized against sexually transmitted diseases, skin troubles, diabetes, rheumatism, cough, and quinsy. The key challenge experienced in the standardization of herbal drugs is the lack of proper identification of plant source. Therefore there is certainly have to establish quality control parameters by utilizing pharmacognostic and phytochemical evaluation, that ensure the purity, safety, and efficacy of medicinal plant A. pilosa. Aim: To assess pharmacognostic characteristics which include macroscopic, microscopic and physicochemical parameters of the root of A. pilosa. Methods: Micro and Macroscopic characters of fresh and dried root samples were investigated. Physicochemical parameters had been done by using WHO recommended parameters, preliminary phytochemical and fluorescent analysis of root sample were carried out for proper identification and standardization of root of A. pilosa. Results: The color, shape, size, odor, and surface characteristics were noted from the root and powdered root material of A. pilosa. Light electron microscope i.e., Olympus CX-21i trinocular Microscope images of cross section of root and powdered root revealed that the presence of cork cells, Xylem fibers with tapered ends, lignified xylem vessels, phloem fibers, medullary rays, sclerides and parenchymatous cells. Phytochemical screening showed the presence of flavonoids, alkaloids, tannins, phenols, steroids, acid compounds, glycosides, amino acids, and proteins. Physicochemical parameters such as moisture content, ash value, extractive value and fluorescent behavior of root powder were determined. These parameters are helpful to differentiate the powdered drug material. Conclusion: The current research is useful in order to supplement the information with regard to its

Effects of chicory root powder on growth performance and histomorphometry of jejunum in broiler chicks

Directory of Open Access Journals (Sweden)

Homan Izadi

2013-09-01

Full Text Available In the present study, chicory root powder (CRP as growth promoter at 1% and 3% levels was supplemented in broilers’ diet to investigate the growth performance and histo- morphometry of jejunum. One hundred twenty, one-day-old male broilers were used in a completely randomized design (CRD with 3 treatments and 4 replicates (10 chicks per replicate. At the end of each period (0-10, 11-24 and 0-24 days, feed intake (FI, weight gain (WG, and feed conversion ratio (FCR were measured. At the end of experiment (day 24, one bird per replicate was sacrificed for breast weight (BW, drumstick weight (DW, and jejunum length (JL as a percentage of body weight, and histomorphometry of villus. The FI increased by 3% CRP in the 1st period (p < 0.01. The percentage of WG significantly increased at 1% during the 1st period and, in the 2nd and total periods, it increased only at 3% CRP (p < 0.05. The FCR decreased at 1% in the 1st (p < 0.04 and, at 3% in the 2nd (p < 0.01 and total periods (p < 0.05. The percentage of DW increased at 3% CRP (p < 0.05. The treatments increased the percentage of BW (p < 0.059 and, percentage of JL (p < 0.079 as well. The villus width and, crypt depth (CD at 1% and 3% CRP and, villus surface at 3% reduced. The 3% CRP increased the villus length (VL and villi number (p < 0.05 and, VL/CD (p < 0.01 and, villus surface area (p < 0.02. The percentage of leaf-like villi decreased in CRP treatments (p < 0.05. The number of goblet cells increased in CRP treatments (p < 0.01. In conclusion, chicory root powder can improve growth performance in broilers by enhancing food digestion and absorption through modification of jejunum histomorphometry.

The Survey of Withani somnifera Extraction against Resistant Strains of Pseudomonas aeruginosa Bacteria to Selective Antibiotics

Directory of Open Access Journals (Sweden)

Mohammad Bokaeian

2015-11-01

Full Text Available Introduction:  Due  to  more  resistance  of  pathogenic  bacteria  to  new  and  current antibiotics  researchers  are  looking  to  find  the  agents  of  herbal  with  antimicrobial activities in order to replace chemical drugs.Methods:   The herbal extract of Withani somnifera was done by using a rotary vacuum,20 strains of Pseudomons aeruginosa were isolated from urinary infections hospitalized patients  in  city of Zabol  hospital.  The  MIC  Withani  somnifera  were  determined  by dilution method in various concentrations. Sensitivity of strains to multiple antibiotics was evaluated by standard disk diffusion Kirby-Bauer.Results:    The  result  showed  that  P.  aeruginosa  were  resistance  to  4  of the  agents including ampicillin  (85%, nitrofurantoin  (65%, nalidixic acid  (65%, ciprofloxacin (15% and for 5 strains of Pseudomonas showed MIC with activity of 100 ppm.Conclusion:   This  study  has  suggested  the  effect  of  winter  cherry  extract  on  P. aeruginosa in the in vitro assay. It s effectiveness of on in vivo system can be examined in future.

Azadirachtin powder for control of root-knot nematodes in tomato

Science.gov (United States)

USDA ARS Daniel K. Inouye U.S. Pacific Basin Agricultural Research Center, 64 Nowelo St., Hilo, HI 96720. Root-knot nematodes cause root galling and yield reductions in many vegetable crops, including tomato. Three organic treatments to improve root growth and reduce nematode infestation were eval...

Identification of anti-biofilm components in Withania somnifera and their effect on virulence of Streptococcus mutans biofilms.

Science.gov (United States)

Pandit, S; Cai, J N; Song, K Y; Jeon, J G

2015-08-01

The aim of this study was to identify components of the Withania somnifera that could show anti-virulence activity against Streptococcus mutans biofilms. The anti-acidogenic activity of fractions separated from W. somnifera was compared, and then the most active anti-acidogenic fraction was chemically characterized using gas chromatography-mass spectroscopy. The effect of the identified components on the acidogenicity, aciduricity and extracellular polymeric substances (EPS) formation of S. mutans UA159 biofilms was evaluated. The change in accumulation and acidogenicity of S. mutans UA159 biofilms by periodic treatments (10 min per treatment) with the identified components was also investigated. Of the fractions, n-hexane fraction showed the strongest anti-acidogenic activity and was mainly composed of palmitic, linoleic and oleic acids. Of the identified components, linoleic and oleic acids strongly affected the acid production rate, F-ATPase activity and EPS formation of the biofilms. Periodic treatment with linoleic and oleic acids during biofilm formation also inhibited the biofilm accumulation and acid production rate of the biofilms without killing the biofilm bacteria. These results suggest that linoleic and oleic acids may be effective agents for restraining virulence of S. mutans biofilms. Linoleic and oleic acids may be promising agents for controlling virulence of cariogenic biofilms and subsequent dental caries formation. © 2015 The Society for Applied Microbiology.

Effects of synthetic hormone substitutes and genotypes on rooting ...

African Journals Online (AJOL)

The vine cuttings were sampled for rooting percentage, number of roots, root length and mini tuber initiation 21 days after treatment (DAT). The number and weight of tubers obtained from IBA and wood ash treated vines were not significantly different. The rice straw ash, IBA and neem leaves powder treated vines produced ...

Sun drying of residual annatto seed powder

Directory of Open Access Journals (Sweden)

Dyego da Costa Santos

2015-01-01

Full Text Available Residual annatto seeds are waste from bixin extraction in the food, pharmaceutical and cosmetic industries. Most of this by-product is currently discarded; however, the use of these seeds in human foods through the elaboration of powder added to other commercial powders is seen as a viable option. This study aimed at drying of residual annatto powder, with and without the oil layer derived from the industrial extraction of bixin, fitting different mathematical models to experimental data and calculating the effective moisture diffusivity of the samples. Powder containing oil exhibited the shortest drying time, highest drying rate (≈ 5.0 kg kg-1 min-1 and highest effective diffusivity (6.49 × 10-12 m2 s-1. All mathematical models assessed were a suitable representation of the drying kinetics of powders with and without oil, with R2 above 0.99 and root mean square error values lower than 1.0.

Virus-induced gene silencing of Withania somnifera squalene synthase negatively regulates sterol and defence-related genes resulting in reduced withanolides and biotic stress tolerance.

Science.gov (United States)

Singh, Anup Kumar; Dwivedi, Varun; Rai, Avanish; Pal, Shaifali; Reddy, Sajjalavarahalli Gangireddy Eswara; Rao, Dodaghatta Krishnarao Venkata; Shasany, Ajit Kumar; Nagegowda, Dinesh A

2015-12-01

Withania somnifera (L.) Dunal is an important Indian medicinal plant that produces withanolides, which are triterpenoid steroidal lactones having diverse biological activities. To enable fast and efficient functional characterization of genes in this slow-growing and difficult-to-transform plant, a virus-induced gene silencing (VIGS) was established by silencing phytoene desaturase (PDS) and squalene synthase (SQS). VIGS of the gene encoding SQS, which provides precursors for triterpenoids, resulted in significant reduction of squalene and withanolides, demonstrating its application in studying withanolides biosynthesis in W. somnifera leaves. A comprehensive analysis of gene expression and sterol pathway intermediates in WsSQS-vigs plants revealed transcriptional modulation with positive feedback regulation of mevalonate pathway genes, and negative feed-forward regulation of downstream sterol pathway genes including DWF1 (delta-24-sterol reductase) and CYP710A1 (C-22-sterol desaturase), resulting in significant reduction of sitosterol, campesterol and stigmasterol. However, there was little effect of SQS silencing on cholesterol, indicating the contribution of sitosterol, campesterol and stigmasterol, but not of cholesterol, towards withanolides formation. Branch-point oxidosqualene synthases in WsSQS-vigs plants exhibited differential regulation with reduced CAS (cycloartenol synthase) and cycloartenol, and induced BAS (β-amyrin synthase) and β-amyrin. Moreover, SQS silencing also led to the down-regulation of brassinosteroid-6-oxidase-2 (BR6OX2), pathogenesis-related (PR) and nonexpressor of PR (NPR) genes, resulting in reduced tolerance to bacterial and fungal infection as well as to insect feeding. Taken together, SQS silencing negatively regulated sterol and defence-related genes leading to reduced phytosterols, withanolides and biotic stress tolerance, thus implicating the application of VIGS for functional analysis of genes related to withanolides

Evaluation of the bioavailability of major withanolides of Withania somnifera using an in vitro absorption model system.

Science.gov (United States)

Devkar, Santosh T; Kandhare, Amit D; Sloley, Brian D; Jagtap, Suresh D; Lin, James; Tam, Yun K; Katyare, Surendra S; Bodhankar, Subhash L; Hegde, Mahabaleshwar V

2015-01-01

Withania somnifera (L.) Dunal, shows several pharmacological properties which are attributed mainly to the withanolides present in the root. The efficacy of medicinally active withanolides constituents depends on the absorption and transportation through the intestinal epithelium. We examined these characteristics by employing the Sino-Veda Madin-Darby canine kidney cells culture system, which under in vitro condition shows the absorption characteristics similar to the human intestinal epithelium. Thus, the aim of the present investigation was to assess the bioavailability of individual withanolides. Withanolides were diluted in Hank's buffered saline at a concentration of 2 μg/ml were tested for permeability studies carried out for 1 h duration. Permeability was measured in terms of efflux pump (P eff) in cm/s. P eff values of withanolide A (WN A), withanone (WNN), 1,2-deoxywithastramonolide (1,2 DWM), withanolide B (WN B), withanoside IV-V (WS IV-V), and withaferin A were 4.05 × 10(-5), 2.06 × 10(-5), 1.97 × 10(-5), 1.80 × 10(-5), 3.19 × 10(-6), 3.03 × 10(-6) and 3.30 × 10(-7) respectively. In conclusion, the nonpolar and low molecular weight compounds (WN A, WNN, 1,2 DWM, and WN B) were highly permeable. As against this, the glycosylated and polar WS IV and WS V showed low permeability. Surprisingly and paradoxically, the highly biologically active withaferin A was completely impermeable, suggesting that further studies possibly using human epithelial colorectal adenocarcinoma (Caco-2) cells may be needed to delineate the absorption characteristics of withanolides, especially withaferin A.

Inhibition of aflatoxin B production of Aspergillus flavus, isolated from soybean seeds by certain natural plant products.

Science.gov (United States)

Krishnamurthy, Y L; Shashikala, J

2006-11-01

The inhibitory effect of cowdung fumes, Captan, leaf powder of Withania somnifera, Hyptis suaveolens, Eucalyptus citriodora, peel powder of Citrus sinensis, Citrus medica and Punica granatum, neem cake and pongamia cake and spore suspension of Trichoderma harzianum and Aspergillus niger on aflatoxin B(1) production by toxigenic strain of Aspergillus flavus isolated from soybean seeds was investigated. Soybean seed was treated with different natural products and fungicide captan and was inoculated with toxigenic strain of A. flavus and incubated for different periods. The results showed that all the treatments were effective in controlling aflatoxin B(1) production. Captan, neem cake, spore suspension of T. harzianum, A. niger and combination of both reduced the level of aflatoxin B(1) to a great extent. Leaf powder of W. somnifera, H. suaveolens, peel powder of C. sinensis, C. medica and pongamia cake also controlled the aflatoxin B(1) production. All the natural product treatments applied were significantly effective in inhibiting aflatoxin B(1) production on soybean seeds by A. flavus. These natural plant products may successfully replace chemical fungicides and provide an alternative method to protect soybean and other agricultural commodities from aflatoxin B(1) production by A. flavus.

Ectopic overexpression of WsSGTL1, a sterol glucosyltransferase gene in Withania somnifera, promotes growth, enhances glycowithanolide and provides tolerance to abiotic and biotic stresses.

Science.gov (United States)

Saema, Syed; Rahman, Laiq Ur; Singh, Ruchi; Niranjan, Abhishek; Ahmad, Iffat Zareen; Misra, Pratibha

2016-01-01

Overexpression of sterol glycosyltransferase (SGTL1) gene of Withania somnifera showing its involvement in glycosylation of withanolide that leads to enhanced growth and tolerance to biotic and abiotic stresses. Withania somnifera is widely used in Ayurvedic medicines for over 3000 years due to its therapeutic properties. It contains a variety of glycosylated steroids called withanosides that possess neuroregenerative, adaptogenic, anticonvulsant, immunomodulatory and antioxidant activities. The WsSGTL1 gene specific for 3β-hydroxy position has a catalytic specificity to glycosylate withanolide and sterols. Glycosylation not only stabilizes the products but also alters their physiological activities and governs intracellular distribution. To understand the functional significance and potential of WsSGTL1 gene, transgenics of W. somnifera were generated using Agrobacterium tumefaciens-mediated transformation. Stable integration and overexpression of WsSGTL1 gene were confirmed by Southern blot analysis followed by quantitative real-time PCR. The WsGTL1 transgenic plants displayed number of alterations at phenotypic and metabolic level in comparison to wild-type plants which include: (1) early and enhanced growth with leaf expansion and increase in number of stomata; (2) increased production of glycowithanolide (majorly withanoside V) and campesterol, stigmasterol and sitosterol in glycosylated forms with reduced accumulation of withanolides (withaferin A, withanolide A and withanone); (3) tolerance towards biotic stress (100 % mortality of Spodoptera litura), improved survival capacity under abiotic stress (cold stress) and; (4) enhanced recovery capacity after cold stress, as indicated by better photosynthesis performance, chlorophyll, anthocyanin content and better quenching regulation of PSI and PSII. Our data demonstrate overexpression of WsSGTL1 gene which is responsible for increase in glycosylated withanolide and sterols, and confers better growth and

AGROBACTERIUM-MEDIATED TRANSFORMATION OF COMPOSITAE PLANTS. I. CONSTRUCTION OF TRANSGENIC PLANTS AND «HAIRY» ROOTS WITH NEW PROPERTIES

Directory of Open Access Journals (Sweden)

N. A.Matvieieva

2013-02-01

Full Text Available The review explores some of the recent advances and the author's own researchs concerning biotechnological approaches for Agrobacterium tumefaciens- and A. rhizogenes-mediated transformation of Compositae family plants. This paper reviews the results of genetic transformation of Compositae plants, including edible (Cichorium intybus, Lactuca sativa, oil (Helianthus annuus, decorative (Gerbera hybrida, medical (Bidens pilosa, Artemisia annua, Artemisia vulgaris, Calendula officinalis, Withania somnifera etc. plant species. Some Compositae genetic engineering areas are considered including creation of plants, resistant to pests, diseases and herbicides, to the effect of abiotic stress factors as well as plants with altered phenotype. The article also presents the data on the development of biotechnology for Compositae plants Cynara cardunculus, Arnica montana, Cichorium intybus, Artemisia annua "hairy" roots construction.

Pharmacognostical and phytochemical studies on roots of Bombax ceiba Linn.

Directory of Open Access Journals (Sweden)

Pankaj H. Chaudhary

2014-12-01

Full Text Available Context: Bombax ceiba Linn. (Bombacaceae is a well-known plant for its antihypertensive, antioxidant, antidiabetic, aphrodisiac and uterine tonicity properties. Aims: To study pharmacognostical, physicochemical and phytochemically the roots of this plant. Methods: Pharmacognostical study included the macroscopic characters like size, color, surface characteristics, texture, fracture characteristics and odor of the roots. The intact root as well as powdered drug were studied under a microscope to analyze the cellular characteristics of the drug. Physicochemical parameter like extractive values, loss on drying (LOD, total ash, water-soluble and acid insoluble ash, foaming index and hemolytic index of Bombax ceiba root powder were determined as per WHO guidelines. Preliminary phytochemical screening and qualitative chemical examination studies have been carried out for the various phytoconstituents. HPTLC have also carried out using cyclohexane: diethyl ether: ethyl acetate as mobile phase. Results: Chemical evaluation and TLC studies shown presence of alkaloids, glycosides, flavonoids, steroids, saponins and tannins. The microscopic characters have shown presence of cork, cambium, xylem vessels, stone cells, starch grains, calcium oxalate crystals and phloem fibers. Microscopy analysis of the powder included the cork cells, fibers, calcium oxalate crystals and vessel. The presence of steroids was confirmed in HPTLC fingerprinting studies. Conclusions: Pharmacognostical and preliminary phytochemical screening of Bombax ceiba roots will be useful in order to authenticate, standardize and avoid any adulteration in the raw material. The diagnostic microscopic characters and physicochemical data will be helpful in the development of a monograph. The chromatographic fingerprinting profile can be used to standardize extracts and formulations containing Bombax ceiba roots.

Asparagus Root Regulates Cholesterol Metabolism and Improves Antioxidant Status in Hypercholesteremic Rats

Directory of Open Access Journals (Sweden)

Nishant P. Visavadiya

2009-01-01

Full Text Available Hyperlipidemia/hypercholesteremia are major risk factors for atherosclerosis and cardiovascular diseases. Root of Asparagus racemosus (AR is widely used in Ayurvedic system of medicine in India and is known for its steroidal saponin content. This study was designed to investigate the hypocholesteremic and antioxidant potential of AR root in both normo- and hypercholesteremic animals. Normal and hypercholesteremic male albino rats were administered with root powder of AR (5 and 10 g% dose levels along with normal and hypercholesteremic diets, respectively, for a duration of 4 weeks. Plasma and hepatic lipid profiles, fecal sterol, bile acid excretion and hepatic antioxidant activity were assessed. Inclusion of AR root powder in diet, resulted in a dose-dependant reduction in plasma and hepatic lipid profiles, increased fecal excretion of cholesterol, neutral sterol and bile acid along with increases in hepatic HMG-CoA reductase activity and bile acid content in hypercholesteremic rats. Further, AR root also improved the hepatic antioxidant status (catalase, SOD and ascorbic acid levels. No significant changes in lipid and antioxidant profiles occurred in the normocholesteremic rats administered with AR root powder. AR root appeared to be useful as a dietary supplement that offers a protection against hyperlipidemia/hypercholesteremia in hypercholesteremic animals. The results of the present study indicate that the potent therapeutic phyto-components present in AR root i.e. phytosterols, saponins, polyphenols, flavonoids and ascorbic acid, could be responsible for increased bile acid production, elimination of excess cholesterol and elevation of hepatic antioxidant status in hypercholesteremic conditions.

Pharmacognostic study of Lantana camara Linn. root

Directory of Open Access Journals (Sweden)

Dinesh Kumar

2012-05-01

Full Text Available Objective: The study was carried out to perform the pharmacognostic evaluation of Lantana camara Linn. root. Method: The pharmacognostic evaluation was done in terms of organoleptic, macro-microscopy, fluorescence analysis and physicochemical parameters. Results: The characteristic macroscopic features showed that the root consists of 25-40 cm long, 0.2-4.0 cm thick pieces which are usually branched, shallow, tough, creamish-brown externally, outer surface rough due to longitudinal wrinkles, with hard fracture, characteristic odour and pungent taste. The main microscopic characters of the root shows exfoliating cork, consisting of about 10-15 rows of tangentially elongated, thick-walled cells followed by cortex consisting of polygonal parenchymatous cells, a few containing rhomboidal shaped calcium oxalate crystals. Endodermis consists of 3-4 layers of non-lignified, thick-walled rounded parenchymatous cells followed by a single layer of non-lignified pericycle. Phloem, a wide zone of xylem consisting of lignified pitted vessels and bi-to triseriate medullary rays are also present. Proximate physicochemical analysis of the root power showed loss on drying, total ash, water soluble ash, sulphated ash values as 0.52, 4.26, 3.8 and 5.8 % w/w respectively. Successive extraction of the root powder with petroleum ether, chloroform, alcohol, water yielded 0.19, 0.35, 2.19 and 2.0 % w/w respectively. Fluorescence study imparted characteristic colors to the root powder when observed under visible, short and long wavelength light. Conclusions: Various pharmacognostic parameters evaluated in this study helps in identification and standardization of Lantana camara L. root in crude form.

Numerical analysis of air effect on the powder flow dynamics in the FT4 Powder Rheometer

Directory of Open Access Journals (Sweden)

Nan Wenguang

2017-01-01

Full Text Available The FT4 powder rheometer of Freeman Technology is widely used nowadays in industry for characterisation of particle flow under dynamic conditions of shear strain rate. It measures the work (termed flow energy required to penetrate a rotating impeller into a powder bed. However, little is known about its underlying powder mechanics, i.e. the relationship between the flow energy and the prevailing local shear stress. This has recently been studied, but only for very simple and ideal systems amenable to analysis by DEM. We analyse the effect of gas flow through the powder bed on the flow behaviour of cohesionless particles in FT4 by DEM-CFD simulation. The results show that the relative particle velocities induced by the mean shear speed, is of the same order as that produced by the root of granular temperature. The shear stress in both cases with and without gas flow could be quantified by the inertial number. The flow energy correlates well with the shear stress in front of the blade, and both increase with the inertial number and could be significantly reduced by the upward gas flow.

Virus-Induced Silencing of Key Genes Leads to Differential Impact on Withanolide Biosynthesis in the Medicinal Plant, Withania somnifera.

Science.gov (United States)

Agarwal, Aditya Vikram; Singh, Deeksha; Dhar, Yogeshwar Vikram; Michael, Rahul; Gupta, Parul; Chandra, Deepak; Trivedi, Prabodh Kumar

2018-02-01

Withanolides are a collection of naturally occurring, pharmacologically active, secondary metabolites synthesized in the medicinally important plant, Withania somnifera. These bioactive molecules are C28-steroidal lactone triterpenoids and their synthesis is proposed to take place via the mevalonate (MVA) and 2-C-methyl-d-erythritol-4-phosphate (MEP) pathways through the sterol pathway using 24-methylene cholesterol as substrate flux. Although the phytochemical profiles as well as pharmaceutical activities of Withania extracts have been well studied, limited genomic information and difficult genetic transformation have been a major bottleneck towards understanding the participation of specific genes in withanolide biosynthesis. In this study, we used the Tobacco rattle virus (TRV)-mediated virus-induced gene silencing (VIGS) approach to study the participation of key genes from MVA, MEP and triterpenoid biosynthesis for their involvement in withanolide biosynthesis. TRV-infected W. somnifera plants displayed unique phenotypic characteristics and differential accumulation of total Chl as well as carotenoid content for each silenced gene suggesting a reduction in overall isoprenoid synthesis. Comprehensive expression analysis of putative genes of withanolide biosynthesis revealed transcriptional modulations conferring the presence of complex regulatory mechanisms leading to withanolide biosynthesis. In addition, silencing of genes exhibited modulated total and specific withanolide accumulation at different levels as compared with control plants. Comparative analysis also suggests a major role for the MVA pathway as compared with the MEP pathway in providing substrate flux for withanolide biosynthesis. These results demonstrate that transcriptional regulation of selected Withania genes of the triterpenoid biosynthetic pathway critically affects withanolide biosynthesis, providing new horizons to explore this process further, in planta.

Ashwagandha (Withania somnifera L

African Journals Online (AJOL)

hcm

2014-02-05

Feb 5, 2014 ... the rate of 12.5 t ha-1 helped in maintaining the soil fertility status after ... root drug find an important place in Ayurveda (Khanna et ... Effect of FYM and inorganic phosphorus on growth parameters and yield of alkaloids. FYM.

A farmer friendly and economic IPM strategy to combat root-knot nematodes infesting lentil

Directory of Open Access Journals (Sweden)

Rose Rizvi

2015-12-01

Full Text Available An experiment was conducted to assess the effect of Rhizobium sp., waste tea leaves, eggshell powder, and composted cow dung manure on the root-knot nematode, Meloidogyne incognita, on lentil in Botany department AMU, Aligarh, India. When used alone, composted cow dung was better in reducing galling and nematode multiplication and improving lentil growth followed by eggshell powder, Rhizobium sp., and waste tea leaves. Significant result in the integrated management of M. incognita was obtained when Rhizobium sp. was used in combination with cow dung and eggshell powder (with or without waste tea leaves. Combined application of root nodule bacterium and organic wastes like waste tea leaves, eggshell, and cow dung may be suggested to the farmers/growers or related persons who are having great enthusiasm to establish a lentil production business. Application of these organic materials along with the root nodule bacteria may be helpful to foster soil ecosystem which has been a hot topic in the present scenario.

Death related to consumption of Rauvolfia sp. powder mislabeled as Tabernanthe iboga.

Science.gov (United States)

Gicquel, Thomas; Hugbart, Chloé; Le Devehat, Françoise; Lepage, Sylvie; Baert, Alain; Bouvet, Renaud; Morel, Isabelle

2016-09-01

Powdered roots of iboga (Tabernanthe iboga) contain ibogaine, an alkaloid that has been used to treat addictions. We report the case of a 30-year-old woman who died after ingesting a powder labeled as Tabernanthe iboga she had bought online. Analysis of the powder revealed the absence of ibogaine but the presence of toxic alkaloids (ajmaline, yohimbine and reserpine) found in Rauvolfia sp. plant species. An original and specific LC-MS/MS method developed to quantify ajmaline, yohimbine and reserpine showed respective concentrations of 109.1ng/mL, 98.2ng/mL and 30.8ng/mL in blood, and 1528.2ng/mL, 914.2ng/mL and 561.2ng/mL in bile. Moreover, systematic toxicological analyses of biological samples showed the presence of oxazepam at therapeutic concentration and cannabinoids. Death could be attributed to ingestion of a substantial quantity of crushed roots of Rauvolfia in association with concomitant drug withdrawal. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Pharmacognostic Investigation of Clerodendrum phlomidis Linn. f. Root

Directory of Open Access Journals (Sweden)

Dinesh Kumar

2014-05-01

Full Text Available The present study was aimed to perform the pharmacognostic evaluation of Clerodendrum phlomidis Linn. f. root in terms of organoleptic, fluorescence analysis, macro-microscopy and physicochemical parameters.The characteristic macroscopic study showed that the root consists of 7-15 cm long, 0.2 -3.0 cm thick pieces which are cylindrical, tough and yellowish-brown externally, with hard fracture and slightly astringent taste. The main microscopic characters of the root show exfoliating cork, having10-15 rows of tangentially elongated, thick-walled cells. Cortex consists of round to oval parenchymatous cells, a few containing rhomboid shaped calcium oxalate crystals. Endodermis consists of 3- 4 layers of non-lignified, thick-walled rounded parenchymatous cells followed by a single pericyclic layer. Phloem consists of isodiametric, thin-walled, parenchymatous cells whereas xylem contains lignified pitted vessels. Medullary rays consisting of biseriate layer of lignified and radially elongated parenchymatous cells is narrower in the xylem region during wider in the phloem region. The physicochemical analysis of the root, i.e., total ash, water-soluble ash, sulphated ash are 7.8, 0.9 and 10.3 (% w/w respectively. Further successive extraction of the root powder with petroleum ether, chloroform, alcohol, water yielded 2.2, 2.4, 12.4 and 9.6 (% w/wextracts respectively. Fluorescence study imparted characteristic colours to the root powder when observed under visible, short and long wavelength light. Various pharmacognostic parameters evaluated in this study helps inbotanical identification and standardization of Clerodendrum phlomidis L. root part in crude form and provide the authentic data for the researchers and scientists involved in carrying out further research on this plant part.

Moisture sorption of Thai red curry powder

Directory of Open Access Journals (Sweden)

Sudathip Inchuen

2009-12-01

Full Text Available Moisture sorption study was conducted on Thai red curry powder prepared by two different drying methods, viz. microwave and hot-air drying. Moisture sorption isotherms of the red curry powder at 30 C and water activity in the range of 0.113-0.970 were determined by a static gravimetric method. The isotherms exhibited Type III behaviour. The moisture sorption data were fitted to several sorption models and a non-linear regression analysis method was used to evaluate the constants of the sorption equations. The fit was evaluated using the coefficient of determination (R2, the reduced chi-square (2 and the root mean square error (RMSE. The GAB model followed by the Lewiski-3 model gave the best fit to the experimental data. The monolayer moisture content, taken as the safe minimum moisture level in the red curry powder, was determined using the BET equation and was found to range between 0.080 - 0.085 gram water per gram dry matter.

[The species traceability of the ultrafine powder and the cell wall-broken powder of herbal medicine based on DNA barcoding].

Science.gov (United States)

Xiang, Li; Tang, Huan; Cheng, Jin-le; Chen, Yi-long; Deng, Wen; Zheng, Xia-sheng; Lai, Zhi-tian; Chen, Shi-lin

2015-12-01

Ultrafine powder and cell wall-broken powder of herbal medicine lack of the morphological characters and microscopic identification features. This makes it hard to identify herb's authenticity with traditional methods. We tested ITS2 sequence as DNA barcode in identification of herbal medicine in ultrafine powder and cell wall-broken powder in this study. We extracted genomic DNAs of 93 samples of 31 representative herbal medicines (28 species), which include whole plant, roots and bulbs, stems, leaves, flowers, fruits and seeds. The ITS2 sequences were amplified and sequenced bidirectionally. The ITS2 sequences were identified using Basic Local Alignment Search Tool (BLAST) method in the GenBank database and DNA barcoding system to identify the herbal medicine. The genetic distance was analyzed using the Kimura 2-parameter (K2P) model and the Neighbor-joining (NJ) phylogenetic tree was constructed using MEGA 6.0. The results showed that DNA can be extracted successfully from 93 samples and high quality ITS2 sequences can be amplified. All 31 herbal medicines can get correct identification via BLAST method. The ITS2 sequences of raw material medicines, ultrafine powder and cell wall-broken powder have same sequence in 26 herbal medicines, while the ITS2 sequences in other 5 herbal medicines exhibited variation. The maximum intraspecific genetic-distances of each species were all less than the minimum interspecific genetic distances. ITS2 sequences of each species are all converged to their standard DNA barcodes using NJ method. Therefore, using ITS2 barcode can accurately and effectively distinguish ultrafine powder and cell wall-broken powder of herbal medicine. It provides a new molecular method to identify ultrafine powder and cell wall-broken powder of herbal medicine in the quality control and market supervision.

Oral intake of encapsulated dried ginger root powder hardly affects human thermoregulatory function, but appears to facilitate fat utilization

Science.gov (United States)

Miyamoto, Mayumi; Matsuzaki, Kentaro; Katakura, Masanori; Hara, Toshiko; Tanabe, Yoko; Shido, Osamu

2015-10-01

The present study investigated the impact of a single oral ingestion of ginger on thermoregulatory function and fat oxidation in humans. Morning and afternoon oral intake of 1.0 g dried ginger root powder did not alter rectal temperature, skin blood flow, O2 consumption, CO2 production, and thermal sensation and comfort, or induce sweating at an ambient temperature of 28 °C. Ginger ingestion had no effect on threshold temperatures for skin blood flow or thermal sweating. Serum levels of free fatty acids were significantly elevated at 120 min after ginger ingestion in both the morning and afternoon. Morning ginger intake significantly reduced respiratory exchange ratios and elevated fat oxidation by 13.5 % at 120 min after ingestion. This was not the case in the afternoon. These results suggest that the effect of a single oral ginger administration on the peripheral and central thermoregulatory function is miniscule, but does facilitate fat utilization although the timing of the administration may be relevant.

Seasonal influences on the rooting response of Chir pine (Pinus roxburghii Sarg.

Directory of Open Access Journals (Sweden)

S.K. Sharma

2013-12-01

Full Text Available Rooting ability of the vegetative cutting depends upon the various factors: age, size, and diameter of cutting, season, rooting substrate and concentration of the applied growth hormone. For assessing the seasonal variation in rooting ability of shoot, cuttings were taken from 4 year old hedges. Shoot cuttings were collected after every two months of hedging spring (March, summer (June, autumn (September and winter (December and treated with 4000 ppm Indole Butyric Acid (IBA, mixed with talc powder and planted in vermiculite filled beds. Suitable control was also maintained, wherein only talc powder was applied to the basal portion of cuttings. Periodical observations were taken on cuttings, with regard to root initiation. The cuttings were uprooted after 12 weeks of planting and observations were recorded. Highly significant differences were observed between root length, shoot length, number of roots per cutting and rooting percentage. This has led to the evaluation of a standard technique for application of mass clonal propagation of Chir pine during summer season (June, which would result into a good success in rooting percentage. This technique could also be helpful in the establishment of germplasm banks of desired genotypes and Clonal Seed Orchards (CSOs. Further, this will also help in overcoming the problem of stock and scion incompatibility, which is commonly faced, when Clonal Seed Orchards are established through grafted material. 

Reduction of Sodium Arsenite-Mediated Adverse Effects in Mice using Dietary Supplementation of Water Hyacinth (Eichornia crassipes) Root Powder.

Science.gov (United States)

Sarker, Rim Sabrina Jahan; Ahsan, Nazmul; Hossain, Khaled; Ghosh, Paritosh Kumar; Ahsan, Chowdhury Rafiqul; Akhand, Anwarul Azim

2012-07-01

In this study, we evaluated the protective effects of water Hyacinth Root Powder (HRP) on arsenic-mediated toxic effects in mice. Swiss albino mice, used in this study, were divided into four different groups (for each group n=5). The control group was supplied with normal feed and water, Arsenic group (As-group) was supplied with normal feed plus arsenic (sodium arsenite)-containing water, and arsenic+hyacinth group (As+Hy group) was supplied with feed supplemented with HRP plus arsenic water. The remaining Hy-group was supplied with feed supplemented with HRP plus normal water. Oral administration of arsenic reduced the normal growth of the mice as evidenced by weight loss. Interestingly, tip of the tails of these mice developed wound that caused gradual reduction of the tail length. Supplementation of HRP in feed significantly prevented mice growth retardation and tail wounding in As+Hy group mice. However, the growth pattern in Hy-group mice was observed to be almost similar to that of the control group indicating that HRP itself has no toxic or negative effect in mice. Ingested arsenic also distorted the shape of the blood cells and elevated the serum enzymes such as lactate dehydrogenase (LDH), alkaline phosphatase (ALP) and serum glutamic pyruvic transaminase (SGPT). Importantly, elevation of these enzymes and distortion of blood cell shape were partially reduced in mice belong to As+Hy group, indicating HRP-mediated reduction of arsenic toxicity. Therefore, the preventive effect of hyacinth root on arsenic-poisoned mice suggested the future application of hyacinth to reduce arsenic toxicity in animal and human.

Modeling of Powder Bed Manufacturing Defects

Science.gov (United States)

Mindt, H.-W.; Desmaison, O.; Megahed, M.; Peralta, A.; Neumann, J.

2018-01-01

Powder bed additive manufacturing offers unmatched capabilities. The deposition resolution achieved is extremely high enabling the production of innovative functional products and materials. Achieving the desired final quality is, however, hampered by many potential defects that have to be managed in due course of the manufacturing process. Defects observed in products manufactured via powder bed fusion have been studied experimentally. In this effort we have relied on experiments reported in the literature and—when experimental data were not sufficient—we have performed additional experiments providing an extended foundation for defect analysis. There is large interest in reducing the effort and cost of additive manufacturing process qualification and certification using integrated computational material engineering. A prerequisite is, however, that numerical methods can indeed capture defects. A multiscale multiphysics platform is developed and applied to predict and explain the origin of several defects that have been observed experimentally during laser-based powder bed fusion processes. The models utilized are briefly introduced. The ability of the models to capture the observed defects is verified. The root cause of the defects is explained by analyzing the numerical results thus confirming the ability of numerical methods to provide a foundation for rapid process qualification.

Production of the biopesticide azadirachtin by hairy root cultivation of Azadirachta indica in liquid-phase bioreactors.

Science.gov (United States)

Srivastava, Smita; Srivastava, Ashok K

2013-11-01

Batch cultivation of Azadirachta indica hairy roots was carried out in different liquid-phase bioreactor configurations (stirred-tank, bubble column, bubble column with polypropylene basket, and polyurethane foam disc as root supports) to investigate possible scale-up of the A. indica hairy root culture for in vitro production of the biopesticide azadirachtin. The hairy roots failed to grow in the conventional bioreactor designs (stirred tank and bubble column). However, modified bubble column reactor (with polyurethane foam as root support) configuration facilitated high-density culture of A. indica hairy roots with a biomass production of 9.2 g l(-1)dry weight and azadirachtin yield of 3.2 mg g(-1) leading to a volumetric productivity of azadirachtin as 1.14 mg l(-1) day(-1). The antifeedant activity in the hairy roots was also evaluated by no choice feeding tests with known concentrations of the hairy root powder and its solvent extract separately on the desert locust Schistocerca gregaria. The hairy root powder and its solvent extract demonstrated a high level of antifeedant activity (with an antifeedant index of 97 % at a concentration of 2 % w/v and 83 % at a concentration of 0.05 % (w/v), respectively, in ethanol).

Antimicrobial activity and probable mechanisms of action of medicinal plants of Kenya: Withania somnifera, Warbugia ugandensis, Prunus africana and Plectrunthus barbatus.

Directory of Open Access Journals (Sweden)

Peter G Mwitari

Full Text Available Withania somnifera, Warbugia ugandensis, Prunus africana and Plectrunthus barbatus are used traditionally in Kenya for treatment of microbial infections and cancer. Information on their use is available, but scientific data on their bioactivity, safety and mechanisms of action is still scanty. A study was conducted on the effect of organic extracts of these plants on both bacterial and fungal strains, and their mechanisms of action. Extracts were evaluated through the disc diffusion assay. Bacteria and yeast test strains were cultured on Mueller-Hinton agar and on Sabouraud dextrose agar for the filamentous fungi. A 0.5 McFarland standard suspension was prepared. Sterile paper discs 6 mm in diameter impregnated with 10 µl of the test extract (100 mg/ml were aseptically placed onto the surface of the inoculated media. Chloramphenicol (30 µg and fluconazole (25 µg were used as standards. Discs impregnated with dissolution medium were used as controls. Activity of the extracts was expressed according to zone of inhibition diameter. MIC was determined at 0.78-100 mg/ml. Safety studies were carried using Cell Counting Kit 8 cell proliferation assay protocol. To evaluate extracts mechanisms of action, IEC-6 cells and RT-PCR technique was employed in vitro to evaluate Interleukin 7 cytokine. Investigated plants extracts have both bactericidal and fungicidal activity. W. ugandensis is cytotoxic at IC50200 µg/ml. Fractions from W. ugandensis and W. somnifera too demonstrated antimicrobial activity. Mechanisms of action can largely be attributed to cytotoxicity, Gene silencing and immunopotentiation. Use of medicinal plants in traditional medicine has been justified and possible mechanisms of action demonstrated. Studies to isolate and characterize the bioactive constituents continue.

Modulatory effect of Althaea officinalis L root extract on cisplatin ...

African Journals Online (AJOL)

AORE) on cisplatininduced cytotoxicity and cell proliferation in a lung cancer cell line. Methods: Aqueous AORE was obtained from peeled and powdered roots. The effect of cisplatin on cytotoxicity and cell proliferation was studied. The cisplatin ...

Research Paper ISSN 0189-6016©2008

African Journals Online (AJOL)

AJTCAM

inflammatory, antitumor and antioxidant properties (Sharada et al., 1996; Bhattacharya et al., ... Withaferin-A (WA) was extracted and isolated from commercially available Withania somnifera root ..... Chemomodulatory efficacy of Basil leaf (Ocimum ... In vitro human phase I metabolism of xenobiotics I: pesticides and related.

Evaluation of different types of rooting stimulators

Directory of Open Access Journals (Sweden)

Petr Salaš

2012-01-01

Full Text Available This paper focuses on the assessment of selected stimulators, especially from Rhizopon product line, which are used for rooting and root system enhancement in various ornamental woody species. Two available methods of cuttings stimulation were selected from the available range of rooting stimulators: stimulation by long-term immersion in solutions or treatment of cuttings with powder stimulators. The experiment involved stimulators with two active components, currently the most commonly used phytohormones for this purpose – IBA and NAA – that were applied in different concentrations. The experiment took place in three propagation terms with twelve coniferous and deciduous shrub varieties. The results of the experiment show the different reactions of the individual species as well as varieties on the respective term of propagation and used form of stimulator.

Forensic DNA typing from teeth using demineralized root tips.

Science.gov (United States)

Corrêa, Heitor Simões Dutra; Pedro, Fabio Luis Miranda; Volpato, Luiz Evaristo Ricci; Pereira, Thiago Machado; Siebert Filho, Gilberto; Borges, Álvaro Henrique

2017-11-01

Teeth are widely used samples in forensic human genetic identification due to their persistence and practical sampling and processing. Their processing, however, has changed very little in the last 20 years, usually including powdering or pulverization of the tooth. The objective of this study was to present demineralized root tips as DNA sources while, at the same time, not involving powdering the samples or expensive equipment for teeth processing. One to five teeth from each of 20 unidentified human bodies recovered from midwest Brazil were analyzed. Whole teeth were demineralized in EDTA solution with daily solution change. After a maximum of approximately seven days, the final millimeters of the root tip was excised. This portion of the sample was used for DNA extraction through a conventional organic protocol. DNA quantification and STR amplification were performed using commercial kits followed by capillary electrophoresis on 3130 or 3500 genetic analyzers. For 60% of the unidentified bodies (12 of 20), a full genetic profile was obtained from the extraction of the first root tip. By the end of the analyses, full genetic profiles were obtained for 85% of the individuals studied, of which 80% were positively identified. This alternative low-tech approach for postmortem teeth processing is capable of extracting DNA in sufficient quantity and quality for forensic casework, showing that root tips are viable nuclear DNA sources even after demineralization. Copyright © 2017 Elsevier B.V. All rights reserved.

Characteristics of Inconel Powders for Powder-Bed Additive Manufacturing

Directory of Open Access Journals (Sweden)

Quy Bau Nguyen

2017-10-01

Full Text Available In this study, the flow characteristics and behaviors of virgin and recycled Inconel powder for powder-bed additive manufacturing (AM were studied using different powder characterization techniques. The results revealed that the particle size distribution (PSD for the selective laser melting (SLM process is typically in the range from 15 μm to 63 μm. The flow rate of virgin Inconel powder is around 28 s·(50 g−1. In addition, the packing density was found to be 60%. The rheological test results indicate that the virgin powder has reasonably good flowability compared with the recycled powder. The inter-relation between the powder characteristics is discussed herein. A propeller was successfully printed using the powder. The results suggest that Inconel powder is suitable for AM and can be a good reference for researchers who attempt to produce AM powders.

Pharmacognostical and phytochemical studies of Helleborus niger L root

Directory of Open Access Journals (Sweden)

V Kishor Kumar

2017-01-01

Full Text Available Background: Helleborus niger L (Ranunculaceae is used Ayurvedic and Unani systems and other herbal medicine systems. The roots of H. niger have a good medicinal value. Aims: To conduct a pharmacognostical and phytochemical study of H. niger. Materials and Methods: The pharmacognostical studies on roots including parameters such as taxonomical, macroscopic, microscopic characters, physico-chemical, ultra-violet analysis and phytochemical studies are established. Results: Macroscopically, the roots are brownish-black in colour, cylindrical in shape, feeble odour, slightly acrid taste with irregularly branched. Microscopically the root showed the presence of epidermis, air-chambers, fissure periderm, periderm, inner cortex, pith, phloem, xylem, vessels and xylem vessels. Microscopic examination of the powder showed the presence of parenchyma cells, parenchyma mass, periderm, cell inclusion, laticifer, lateral wall pith, perforation, xylem bundle and xylem elements. Ultra-violet and ordinary light analyses with different reagents were conducted to identify the drug in powder form. Physico-chemical evaluation established, Ash values - Total, acid insoluble, water soluble and sulphated ash values were 7.3%, 4.1%, 3.7% and 5.2%, respectively. Extractive values - Alcohol soluble, water soluble and ether soluble extractive values were 22.8%, 7.4% and 5.6%, respectively. Loss on drying was 3.3%. Preliminary phytochemical screening showed the presence of carbohydrate, glycoside, saponins, flavonoid, phytosterols, tannins and phenolic compounds. Conclusions: The results of the study can serve as a valuable resource of pharmacognostic and phytochemical information. This will serve as appropriate, standards for discovery of this plant material in future investigations and applications and also contribute towards establishing pharmacopoeial standards.

A farmer friendly and economic IPM strategy to combat root-knot nematodes infesting lentil

OpenAIRE

Rose Rizvi; Rizwan Ali Ansari; Gulshan Zehra; Irshad Mahmood

2015-01-01

An experiment was conducted to assess the effect of Rhizobium sp., waste tea leaves, eggshell powder, and composted cow dung manure on the root-knot nematode, Meloidogyne incognita, on lentil in Botany department AMU, Aligarh, India. When used alone, composted cow dung was better in reducing galling and nematode multiplication and improving lentil growth followed by eggshell powder, Rhizobium sp., and waste tea leaves. Significant result in the integrated management of M. incognita was obtain...

Synthesis of Uranium nitride powders using metal uranium powders

International Nuclear Information System (INIS)

Yang, Jae Ho; Kim, Dong Joo; Oh, Jang Soo; Rhee, Young Woo; Kim, Jong Hun; Kim, Keon Sik

2012-01-01

Uranium nitride (UN) is a potential fuel material for advanced nuclear reactors because of their high fuel density, high thermal conductivity, high melting temperature, and considerable breeding capability in LWRs. Uranium nitride powders can be fabricated by a carbothermic reduction of the oxide powders, or the nitriding of metal uranium. The carbothermic reduction has an advantage in the production of fine powders. However it has many drawbacks such as an inevitable engagement of impurities, process burden, and difficulties in reusing of expensive N 15 gas. Manufacturing concerns issued in the carbothermic reduction process can be solved by changing the starting materials from oxide powder to metals. However, in nitriding process of metal, it is difficult to obtain fine nitride powders because metal uranium is usually fabricated in the form of bulk ingots. In this study, a simple reaction method was tested to fabricate uranium nitride powders directly from uranium metal powders. We fabricated uranium metal spherical powder and flake using a centrifugal atomization method. The nitride powders were obtained by thermal treating those metal particles under nitrogen containing gas. We investigated the phase and morphology evolutions of powders during the nitriding process. A phase analysis of nitride powders was also a part of the present work

Fluorescence Analysis on the Roots of Rauvolfia Serpentina (L.) Benth. Ex Kurz Under UV Radiation

Science.gov (United States)

Selvam, A.B.D; Bandyopadhyay, S.

2005-01-01

The present study deals with an analysis of the roots of Rauvolfia serpentine (L) Benth. Ex Kurz under ultraviolet radiation and also under daylight. The coarsely powdered roots were treated with various chemical reagents and the characteristic fluorescence patterns emitted were recorded and are reported in this paper. This study was undertaken as a pharmacognostic standardization to ascertain the authenticity of the roots of this plant in its crude form and also to check any adulteration that may be used in trade. PMID:22557172

Studies on the anti-radiation activity of ashwagandha

International Nuclear Information System (INIS)

Gandhi, R.; Kaul, B.L.

1984-01-01

Experiments were carried out to see if root extracts of Withania somnifera (ashwagandha), a reputed anti-ageing drug of 'Ayurveda', gives protection against the simulated ageing effects of ionizing radiations. Strong radioprotective ability was shown by the drug when it was found to be associated with the presence of steroidal lactones in the extract. (author)

The ex vitro rooting of blueberry (Vaccinium corymbosum L. microcuttings

Directory of Open Access Journals (Sweden)

Pacholczak Andrzej

2015-12-01

Full Text Available A growing demand for blueberry fruit has necessitated the development of an efficient propagation method of this species that would provide large quantities of planting material. The aim of this study was to evaluate the effects of auxin indole-3-butyric acid (IBA 50 mg dm−3, the commercial rooting powder Rhizopon containing 1% IBA, and salicylic acid (50 mg dm−3 on the in vivo rooting of microcuttings of Vaccinium corymbosum ‘Bluecrop’ and ‘Duke’. The contents of chlorophyll a + b, soluble proteins, free amino acids, as well as total soluble and reducing sugars were determined in rooted cuttings. All of the treatments increased the degree and percentage of rooting in the cuttings of both cultivars. While improving rhizogenesis in blueberry, salicylic acid did not perform as a cofactor of the auxin IBA. Foliar applications of IBA or salicylic acid (SA increased the contents of soluble proteins, free amino acids and sugars, but no effects on chlorophyll levels were observed.

Studies on the anti-radiation activity of ashwagandha

Energy Technology Data Exchange (ETDEWEB)

Gandhi, R.; Kaul, B.L. (Regional Research Lab., Jammu (India))

1984-12-14

Experiments were carried out to see if root extracts of Withania somnifera (ashwagandha), a reputed anti-ageing drug of 'Ayurveda', gives protection against the simulated ageing effects of ionizing radiations. Strong radioprotective ability was shown by the drug when it was found to be associated with the presence of steroidal lactones in the extract.

Validation of dbEST-SSRs and transferability of some other solanaceous species SSR in ashwagandha [Withania Somnifera (L.) Dunal].

Science.gov (United States)

Parmar, Eva K; Fougat, Ranbir S; Patel, Chandni B; Zala, Harshvardhan N; Patel, Mahesh A; Patel, Swati K; Kumar, Sushil

2015-12-01

Cross-species transferability and expressed sequence tags (ESTs) in public databases are cost-effective means for developing simple sequence repeats (SSRs) for less-studied species like medicinal plants. In this study, 11 EST-SSR markers developed from 742 available ESTs of Withania Somnifera EST sequences and 95 SSR primer pairs derived from other solanaceous crops (tomato, eggplant, chili, and tobacco) were utilized for their amplification and validation. Out of 11, 10 EST-SSRs showed good amplification quality and produced 13 loci with a product size ranging between 167 and 291 bp. Similarly, of the 95 cross-genera SSR loci assayed, 20 (21 %) markers showed the transferability of 5, 27, 32, and 14.2 % from eggplant, chili, tomato, and tobacco, respectively, to ashwagandha. In toto, these 30 SSR markers reported here will be valuable resources and may be applicable for the analysis of intra- and inter-specific genetic diversity in ashwagandha for which till date no information about SSR is available.

New Strategies for Powder Compaction in Powder-based Rapid Prototyping Techniques

OpenAIRE

Budding, A.; Vaneker, T.H.J.

2013-01-01

In powder-based rapid prototyping techniques, powder compaction is used to create thin layers of fine powder that are locally bonded. By stacking these layers of locally bonded material, an object is made. The compaction of thin layers of powder mater ials is of interest for a wide range of applications, but this study solely focuses on the application for powder -based three-dimensional printing (e.g. SLS, 3DP). This research is primarily interested in powder compaction for creating membrane...

Corrosion-resistant powder-metallurgy stainless steel powders and compacts therefrom

International Nuclear Information System (INIS)

Klar, E.; Ro, D.H.; Whitman, C.I.

1980-01-01

Disclosed is a process for improving the corrosion resistance of a stainless steel powder or compact thereof wherein the powder is produced by atomizing a melt of metals in an oxidizing environment whereby the resulting stainless steel powder is surface-enriched in silicon oxides. The process comprises adding an effective proportion of modifier metal to the melt prior to the atomization, the modifier metal selected from the group consisting of tin, aluminum, lead, zinc, magnesium, rare earth metals and like metals capable of enrichment about the surface of the resulting atomized stainless steel powder and effective under reductive sintering conditions in the depletion of the silicon oxides about the surface; and sintering the resulting atomized powder or a compact thereof under reducing conditions, the sintered powder or compact thereof being depleted in the silicon oxides and the corrosion resistance of the powder or compact thereof being improved thereby

Light extinction in metallic powder beds: Correlation with powder structure

International Nuclear Information System (INIS)

Rombouts, M.; Froyen, L.; Gusarov, A.V.; Bentefour, E.H.; Glorieux, C.

2005-01-01

A theoretical correlation between the effective extinction coefficient, the specific surface area, and the chord length distribution of powder beds is verified experimentally. The investigated powder beds consist of metallic particles of several tens of microns. The effective extinction coefficients are measured by a light-transmission technique at a wavelength of 540 nm. The powder structure is characterized by a quantitative image analysis of powder bed cross sections resulting in two-point correlation functions and chord length distributions. The specific surface area of the powders is estimated by laser-diffraction particle-size analysis and by the two-point correlation function. The theoretically predicted tendency of increasing extinction coefficient with specific surface area per unit void volume is confirmed by the experiments. However, a significant quantitative discrepancy is found for several powders. No clear correlation of the extinction coefficient with the powder material and particle size, and morphology is revealed, which is in line with the assumption of geometrical optics

An alternative magnesium-based root canal disinfectant: Preliminary study of its efficacy against Enterococcus faecalis and Candida albicans in vitro

Directory of Open Access Journals (Sweden)

Lin Zhu

2014-10-01

Full Text Available Organisms invading root canal systems result in serious pulpal and periapical disease. To eliminate microorganisms and restrain secondary infections, dental materials with antibacterial properties are urgently needed in endodontics. Magnesium is considered as a promising biodegradable and biocompatible implant material. However, there are barely researches about its application in endodontic therapy. This work investigated the in vitro efficacy of magnesium powder against Enterococcus faecalis and Candida albicans compared with a common disinfectant, calcium hydroxide. With Calcium hydroxide served as a comparison it demonstrated the qualified antibacterial and anti-fungus properties of Mg as root canal disinfectant due to its high alkalinity of degradation, and the antimicrobial efficacy enhanced with the decreasing powder size.

Chondroprotective potential of root extracts of Withania somnifera in ...

Indian Academy of Sciences (India)

PRAKASH

Interactive Research School for Health Affairs (IRSHA), Bhartiya Vidyapeeth Deemed University ... (13 mm, 0.45 µm CN membrane) for each experiment. ... at –20°C. All CM samples per OA patient were thawed and .... This was true for.

New Strategies for Powder Compaction in Powder-based Rapid Prototyping Techniques

NARCIS (Netherlands)

Budding, A.; Vaneker, Thomas H.J.

2013-01-01

In powder-based rapid prototyping techniques, powder compaction is used to create thin layers of fine powder that are locally bonded. By stacking these layers of locally bonded material, an object is made. The compaction of thin layers of powder mater ials is of interest for a wide range of

Study of sorption behavior, shelf life and colour kinetics of vacuum puffed honey powder at accelerated storage conditions.

Science.gov (United States)

Devi, K Deepika; Paul, Sanjib Kr; Sahu, Jatindra K

2016-05-01

In the study, the storage life of vacuum puffed honey powder at accelerated storage environment (90 % relative humidity and 36 °C) was computed by determining the sticky-point moisture content as the critical parameter of the honey powder. The value of monolayer moisture content in the GAB model was calculated to be 0.081 kg water/kg dry solids by fitting water activity and moisture sorption data. Shelf life of the honey powder was predicted to be 222 days when the powder was packaged in aluminum foil-laminated polyethylene pouches with permeability value of 5.427X10(-8) kg/m(2)//day/Pa. Actual shelf life of honey powder was experimentally determined as 189 days and analysis of mean relative percent derivation modulus (Rd) and root mean square (RMS) established the accuracy and acceptability of the technique for the prediction of shelf life of honey powder. Overall colour deviation pattern followed first order reaction kinetics with rate constant (k1) as 0.037 day(-1). This study revealed overall colour difference of 18.1 till the end of shelf life with drastic change during initial storage period.

Aluminum powder metallurgy processing

Energy Technology Data Exchange (ETDEWEB)

Flumerfelt, J.F.

1999-02-12

The objective of this dissertation is to explore the hypothesis that there is a strong linkage between gas atomization processing conditions, as-atomized aluminum powder characteristics, and the consolidation methodology required to make components from aluminum powder. The hypothesis was tested with pure aluminum powders produced by commercial air atomization, commercial inert gas atomization, and gas atomization reaction synthesis (GARS). A comparison of the GARS aluminum powders with the commercial aluminum powders showed the former to exhibit superior powder characteristics. The powders were compared in terms of size and shape, bulk chemistry, surface oxide chemistry and structure, and oxide film thickness. Minimum explosive concentration measurements assessed the dependence of explosibility hazard on surface area, oxide film thickness, and gas atomization processing conditions. The GARS aluminum powders were exposed to different relative humidity levels, demonstrating the effect of atmospheric conditions on post-atomization processing conditions. The GARS aluminum powders were exposed to different relative humidity levels, demonstrating the effect of atmospheric conditions on post-atomization oxidation of aluminum powder. An Al-Ti-Y GARS alloy exposed in ambient air at different temperatures revealed the effect of reactive alloy elements on post-atomization powder oxidation. The pure aluminum powders were consolidated by two different routes, a conventional consolidation process for fabricating aerospace components with aluminum powder and a proposed alternative. The consolidation procedures were compared by evaluating the consolidated microstructures and the corresponding mechanical properties. A low temperature solid state sintering experiment demonstrated that tap densified GARS aluminum powders can form sintering necks between contacting powder particles, unlike the total resistance to sintering of commercial air atomization aluminum powder.

Cassava root husks powder as green adsorbent for the removal of Cu(II) from natural river water

Energy Technology Data Exchange (ETDEWEB)

Jorgetto, A.O.; Silva, R.I.V.; Saeki, M.J.; Barbosa, R.C. [IB-UNESP, Dept. Química e Bioquímica, C.P. 510, 18618-000 Botucatu, SP (Brazil); Martines, M.A.U. [UFMS – Dept. Química, 79074-460 Campo Grande, MS (Brazil); Jorge, S.M.A.; Silva, A.C.P. [IB-UNESP, Dept. Química e Bioquímica, C.P. 510, 18618-000 Botucatu, SP (Brazil); Schneider, J.F. [USP – Instituto de Física de São Carlos, 13566-590 São Carlos, SP (Brazil); Castro, G.R., E-mail: castrogr@ibb.unesp.br [IB-UNESP, Dept. Química e Bioquímica, C.P. 510, 18618-000 Botucatu, SP (Brazil)

2014-01-01

Through a series of simple processes, cassava root husks were turned into a fine powder of controlled particle size (63–75 μm). FTIR spectrum demonstrated the existence of alcohol, amine and carboxylic groups; and elemental analysis confirmed the presence of elements of interest such as sulphur, nitrogen and oxygen. Cross-polarized {"1H}-{sup 13}C NMR technique indicated the existence of methionine and thiamine through the signals observed at 55 ppm and 54 ppm, respectively, and the point of zero charge (pH{sub pzc}) was achieved at pH 5.2. The material was applied in solid-phase extraction of Cu(II) via batch experiments. Optimum adsorption pH was found to be in range of 3–6 and in the kinetic experiment the equilibrium was attained in 1 min. The highest adsorption capacity was 0.14 mmol g{sup −1}. The adsorption data were fit to the modified Langmuir equation, and the maximum amount of metal species extracted from the solution, N{sub s}, was determined to be ∼0.14 mmol g{sup −1}, which is an indicative that the main adsorption mechanism is through chemisorption. Under optimized conditions, the material was utilized in preconcentration experiments, which culminated in an enrichment factor of 41.3-fold. With the aid of the enrichment factor, experiments were carried out to determine the Cu(II) content in tap water and natural water. Preconcentration method was also applied to a certified reference material (1643e) and the concentration found was 23.03 ± 0.79 μg L{sup −1}, whereas the specified Cu(II) concentration was 22.7 ± 0.31 μg L{sup −1}.

First results of the application of a new Neemazal powder formulation in hydroponics against different pest insects.

Science.gov (United States)

Hummel, Edmund; Kleeberg, Hubertus

2002-01-01

NeemAzal PC (0.5% Azadirachtin) is a new standardised powder formulation from the seed kernels of the tropical Neem tree (Azadirachta indica A. Juss) with an inert carrier. First experiments with beans--as a model-system for hydroponics--show that active ingredient is taken up by the plants through the roots and is transported efficiently with the plant sap to the leaves. After application of NeemAzal PC solution (0.01-1%) to the roots sucking (Aphis fabae Hom., Aphididae) and free feeding (Heliothis armigera Lep., Noctuidae) pest insects can be controlled efficiently. The effects are concentration and time dependent.

Spherical rhenium metal powder

International Nuclear Information System (INIS)

Leonhardt, T.; Moore, N.; Hamister, M.

2001-01-01

The development of a high-density, spherical rhenium powder (SReP) possessing excellent flow characteristics has enabled the use of advanced processing techniques for the manufacture of rhenium components. The techniques that were investigated were vacuum plasma spraying (VPS), direct-hot isostatic pressing (D-HIP), and various other traditional powder metallurgy processing methods of forming rhenium powder into near-net shaped components. The principal disadvantages of standard rhenium metal powder (RMP) for advanced consolidation applications include: poor flow characteristics; high oxygen content; and low and varying packing densities. SReP will lower costs, reduce processing times, and improve yields when manufacturing powder metallurgy rhenium components. The results of the powder characterization of spherical rhenium powder and the consolidation of the SReP are further discussed. (author)

Measurement of loose powder density

International Nuclear Information System (INIS)

Akhtar, S.; Ali, A.; Haider, A.; Farooque, M.

2011-01-01

Powder metallurgy is a conventional technique for making engineering articles from powders. Main objective is to produce final products with the highest possible uniform density, which depends on the initial loose powder characteristics. Producing, handling, characterizing and compacting materials in loose powder form are part of the manufacturing processes. Density of loose metallic or ceramic powder is an important parameter for die design. Loose powder density is required for calculating the exact mass of powder to fill the die cavity for producing intended green density of the powder compact. To fulfill this requirement of powder metallurgical processing, a loose powder density meter as per ASTM standards is designed and fabricated for measurement of density. The density of free flowing metallic powders can be determined using Hall flow meter funnel and density cup of 25 cm/sup 3/ volume. Density of metal powders like cobalt, manganese, spherical bronze and pure iron is measured and results are obtained with 99.9% accuracy. (author)

Contr rol of r root-kn saw not nem wdust matod in tom e by u mato ro ...

African Journals Online (AJOL)

SAM

proved with visualizing mical level a ot-knot nema ard dust ame dust. by- and accum ..... Table 2. Effect of sawdust on length of shoot and root (cm) of tomato plants. ...... Evaluation of powdered pine bark for control of Meloidogyne arenaria.

Fundamentals of powder metallurgy

International Nuclear Information System (INIS)

Khan, I.H.; Qureshi, K.A.; Minhas, J.I.

1988-01-01

This book is being presented to introduce the fundamentals of technology of powder metallurgy. An attempt has been made to present an overall view of powder metallurgy technology in the first chapter, whereas chapter 2 to 8 deal with the production of metal powders. The basic commercial methods of powder production are briefly described with illustrations. Chapter 9 to 12 describes briefly metal powder characteristics and principles of testing, mixing, blending, conditioning, compaction and sintering. (orig./A.B.)

Antibacterial and Cytotoxicity Studies of Silver Nanoparticles Synthesized by Endophytic Fusarium solani Isolated from Withania somnifera (L.

Directory of Open Access Journals (Sweden)

Smitha Vijayan

2016-11-01

Full Text Available The present study establish extracellular production of silver nanoparticles (AgNP using Fusarium solani, from medicinal plant Withania somnifera (L. (ashwagandha and it’s antibacterial and cytotoxicity effects. Biological- AgNP (Bio- AgNP were synthesized by using fungal cell free extract and characterized by SEM, TEM, UV spectroscopy, XRD, FTIR and AFM analysis.  Antibacterial properties were assayed by well diffusion and cytotoxicity by RBC lysis test and MTT assay respectively. X- ray diffraction and microscopic analysis revealed the well dispersed and crystalline nature of spherical nanoparticles with a calculated size ranging from 10 - 50 nm. The Bio-AgNP exhibited significant antibacterial properties in a range of 50-100 µgml-1 against the selected clinical pathogens Escherichia coli,Pseudomonas aeruginosa, Salmonella typhi, Staphylococcus aureus and Klebsiella pneumoniae. The observed hemolysis of 3.906 % at 50 µg ml-1   suggested the safe therapeutic application of Bio - AgNP. MTT assay revealed that at the suggeseted concentration 69 % of cells are viable. These outcomes are extremely encouraging to utilize Bio-AgNP as a medication. Exploiting the endophytic organisms from therapeutic plants for improvement of nanomaterial is a uninvestigated and relatively novel territory. This may improve the likelihood in future to push the limit ahead in nanomedicine.

Low pressure powder injection moulding of stainless steel powders

Energy Technology Data Exchange (ETDEWEB)

Zampieron, J.V.; Soares, J.P.; Mathias, F.; Rossi, J.L. [Powder Processing Center CCP, Inst. de Pesquisas Energeticas e Nucleares, Sao Paulo, SP (Brazil); Filho, F.A. [IPEN, Inst. de Pesquisas Energeticas e Nucleares, Cidade Univ., Sao Paulo, SP (Brazil)

2001-07-01

Low-pressure powder injection moulding was used to obtain AISI 316L stainless steel parts. A rheological study was undertaken using gas-atomised powders and binders. The binders used were based on carnauba wax, paraffin, low density polyethylene and microcrystalline wax. The metal powders were characterised in terms of morphology, particle size distribution and specific surface area. These results were correlated to the rheological behaviour. The mixture was injected in the shape of square bar specimens to evaluate the performance of the injection process in the green state, and after sintering. The parameters such as injection pressure, viscosity and temperature were analysed for process optimisation. The binders were thermally removed in low vacuum with the assistance of alumina powders. Debinding and sintering were performed in a single step. This procedure shortened considerably the debinding and sintering time. (orig.)

Foundations of powder metallurgy

International Nuclear Information System (INIS)

Libenson, G.A.

1987-01-01

Consideration is being given to physicochemical foundations and technology of metal powders, moulding and sintering of bars, made of them or their mixtures with nonmetal powders. Data on he design of basic equipment used in the processes of powder metallurgy and its servicing are presented. General requirements of safety engineering when fabricating metal powders and products of them are mentioned

Delayed replantation of rat teeth after use of reconstituted powdered milk as a storage medium.

Science.gov (United States)

dos Santos, Cláudia Letícia Vendrame; Sonoda, Celso Koogi; Poi, Wilson Roberto; Panzarini, Sônia Regina; Sundefeld, Maria Lúcia Marçal Mazza; Negri, Márcia Regina

2009-02-01

Minimal extraoral dry storage period and moist storage for the avulsed tooth are identified as key steps for the treatment protocol of tooth replantation. Among the possible moist storage media, bovine milk has stood out because of its capacity of preserving the integrity of the periodontal ligament (PDL) fibers. This condition has attracted the attention to investigate the use of powdered milk, which is one of the presentation forms of bovine milk, as a feasible storage medium in cases of delayed tooth replantation. The aim of this study was to evaluate the healing process after delayed replantation of rat teeth stored in reconstituted powdered milk and long shelf-life (ultra high temperature) whole milk. Forty maxillary right rat incisors were assigned to four groups (n = 10): group I--the teeth were extracted and immediately replanted into theirs sockets; group II--the teeth were stored for 60 min in 200 ml of freshly reconstituted powdered milk; group III--the teeth were stored for 60 min in 200 ml of long shelf-life whole milk; group IV--the teeth were kept dry for the same time. All procedures were performed at room temperature. Next, the root canals of teeth in groups II, III, and IV were instrumented, filled with a calcium hydroxide-based paste, and replanted into their sockets. All animals received systemic antibiotic therapy and were killed by anesthetic overdose 60 days after replantation. The pieces containing the replanted teeth were removed, fixed, decalcified, and paraffin-embedded. Semi-serial 6-microm-thick sections were obtained and stained with hematoxylin and eosin for histomorphological analysis. There was statistically significant difference (P < 0.05) between groups I and IV regarding the presence of replacement resorption and PDL remnants on root surface. The powdered milk and long shelf-life whole milk presented similar results to each other and may be indicated as storage media for avulsed teeth.

Use of whey powder and skim milk powder for the production of fermented cream

Directory of Open Access Journals (Sweden)

Ceren AKAL

2016-01-01

Full Text Available Abstract This study is about the production of fermented cream samples having 18% fat by addition of starter cultures. In order to partialy increase non-fat solid content of fermented cream samples, skim milk powder and demineralized whey powder in two different rates (50% and 70% were used. Samples were analyzed for changes in their biochemical and physicochemical properties (total solid, ash, fat, titratable acidity, pH value, total nitrogen, viscosity, tyrosine, acid number, peroxide and diacetyl values during 29-day of storage period. Samples tested consisted of 7 different groups; control group (without adding any powder, skim milk powder, 50% demineralized whey powder and 70% demineralized whey powder samples were in two different addition rate (2% and 4%. Also samples were analyzed for sensory properties. According to the results obtained, the addition of milk powder products affected titratable acidity and tyrosine values of fermented cream samples. Although powder addition and/or storage period didn’t cause significant variations in total solid, ash, fat, pH value, viscosity, acid number, peroxide, tyrosine and diacetyl values; sensory properties of fermented cream samples were influenced by both powder addition and storage period. Fermented cream containing 2% skim milk powder gets the top score of sensory evaluation among the samples.

21 CFR 520.1696a - Buffered penicillin powder, penicillin powder with buffered aqueous diluent.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Buffered penicillin powder, penicillin powder with... FORM NEW ANIMAL DRUGS § 520.1696a Buffered penicillin powder, penicillin powder with buffered aqueous diluent. (a) Specifications. When reconstituted, each milliliter contains penicillin G procaine equivalent...

Biaxially textured articles formed by powder metallurgy

Science.gov (United States)

Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

2003-08-05

A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of ternary mixtures consisting of: Ni powder, Cu powder, and Al powder, Ni powder, Cr powder, and Al powder; Ni powder, W powder and Al powder; Ni powder, V powder, and Al powder; Ni powder, Mo powder, and Al powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

Developing a method of fabricating microchannels using plant root structure

Science.gov (United States)

Nakashima, Shota; Tokumaru, Kazuki; Tsumori, Fujio

2018-06-01

Complicated three-dimensional (3D) microchannels are expected to be applied to a lab-on-a-chip, especially an organ-on-a-chip. There are fine microchannel networks such as blood vessels in a living organ. However, it is difficult to recreate the complicated 3D microchannels of real living structures. Plant roots have a similar structure to blood vessels. They spread radially and three-dimensionally, and become thinner as they branch. In this research, we propose a method of fabricating microchannels using a live plant root as a template to mimic a blood vessel structure. We grew a plant in ceramic slurry instead of soil. The slurry consists of ceramic powder, binder and water, so it plays a similar role to soil consisting of fine particles in water. After growing the plant, the roots inside the slurry were burned and a sintered ceramic body with channel structures was obtained by heating. We used two types of slurry with different composition ratios, and compared the internal channel structures before and after sintering.

An analysis of un-dissolved powders of instant powdered soup by using ultrasonographic image

Science.gov (United States)

Kawaai, Yukinori; Kato, Kunihito; Yamamoto, Kazuhiko; Kasamatsu, Chinatsu

2008-11-01

Nowadays, there are many instant powdered soups around us. When we make instant powdered soup, sometimes we cannot dissolve powders perfectly. Food manufacturers want to improve this problem in order to make better products. Therefore, they have to measure the state and volume of un-dissolved powders. Earlier methods for analyzing removed the un-dissolved powders from the container, the state of the un-dissolved power was changed. Our research using ultrasonographic image can measure the state of un-dissolved powders with no change by taking cross sections of the soup. We then make 3D soup model from these cross sections of soup. Therefore we can observe the inside of soup that we do not have ever seen. We construct accurate 3D model. We can visualize the state and volume of un-dissolved powders with analyzing the 3D soup models.

Biaxially textured articles formed by powder metallurgy

Science.gov (United States)

Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

2003-07-29

A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

Characterization of ceramic powder compacts

International Nuclear Information System (INIS)

Yanai, K.; Ishimoto, S.; Kubo, T.; Ito, K.; Ishikawa, T.; Hayashi, H.

1995-01-01

UO 2 and Al 2 O 3 powder packing structures in cylindrical powder compacts are observed by scanning electron microscopy using polished cross sections of compacts fixed by low viscosity epoxy resin. Hard aggregates which are not destroyed during powder compaction are observed in some of the UO 2 powder compacts. A technique to measure local density in powder compacts is developed based on counting characteristic X-ray intensity by energy dispersive X-ray analysis (EDX). The local density of the corner portion of the powder compact fabricated by double-acting dry press is higher than that of the inner portion. ((orig.))

Operation whey powder

International Nuclear Information System (INIS)

Brunner, E.

1987-01-01

The odyssey of the contaminated whey powder finally has come to an end, and the 5000 tonnes of whey now are designated for decontamination by means of an ion exchange technique. The article throws light upon the political and economic reasons that sent the whey powder off on a chaotic journey. It is worth mentioning in this context that the natural radioactivity of inorganic fertilizers is much higher than that of the whey powder in question. (HP) [de

Densification behavior of aluminum alloy powder mixed with zirconia powder inclusion under cold compaction

International Nuclear Information System (INIS)

Ryu, Hyun Seok; Lee, Sung Chul; Kim, Ki Tae

2002-01-01

Densification behavior of composite powders was investigated during cold compaction. Experimental data were obtained for aluminum alloy powder mixed with zirconia powder inclusion under triaxial compression. The cap model with constraint factors was implemented into a finite element program(ABAQUS) to simulate compaction responses of composite powders during cold compaction. Finite element results were compared with experimental data for densification behavior of composite powders under cold isostatic pressing and die compaction. The agreements between experimental data and finite element calculations from the cap model with constraint factors were good

Nuclear fuel powder transfer device

International Nuclear Information System (INIS)

Komono, Akira

1998-01-01

A pair of parallel rails are laid between a receiving portion to a molding portion of a nuclear fuel powder transfer device. The rails are disposed to the upper portion of a plurality of parallel support columns at the same height. A powder container is disposed while being tilted in the inside of the vessel main body of a transfer device, and rotational shafts equipped with wheels are secured to right and left external walls. A nuclear powder to be mixed, together with additives, is supplied to the powder container of the transfer device. The transfer device engaged with the rails on the receiving side is transferred toward the molding portion. The wheels are rotated along the rails, and the rotational shafts, the vessel main body and the powder container are rotated. The nuclear powder in the tilted powder container disposed is rotated right and left and up and down by the rotation, and the powder is mixed satisfactory when it reaches the molding portion. (I.N.)

Fresh weight and doses of IAA on rooting of goldenrod cuttings

Directory of Open Access Journals (Sweden)

Moisés Alves Muniz

2015-04-01

Full Text Available The objective of this work was to evaluate the influence of indole acetic acid (IAA on fresh weight of cuttings and in the rooting of goldenrod. The first experiment was arranged in randomized blocks in factorial scheme 5 x 3, and 5 doses of IAA at 0, 500, 1000, 2000 and 3000 mg/L and three evaluation periods (7, 14 and 21 days after staking-DAS with six replications. The second experiment was also established in randomized blocks in factorial scheme 4 x 2, with 4 class of fresh weight (0.5-0.7, 0.71-0.9, 0.91-1.10 and greater than 1.10 g in the presence or absence of indol butyric acid (IBA and two evaluation periods (14, 21 days after staking, with six replications. In both experiments, the stakes were standardized to 5 cm. In the first experiment the stakes were 1 cm from its base immersed for 30 seconds in different water-alcohol solutions of IAA, while the second base of the cuttings were immersed in water, and then the powder containing 2000 mg/kg of IBA, and subsequently placed for rooting in trays with 256 cells (45 mL. Number of roots/cutting, rooting and survival of seedlings were determined. The presence or absence of IAA or IBA does not affect the rooting of cuttings and even the survival of seedlings. There was no effect on rooting cycle suggesting that the dosage is 2000 mg/L of IAA, because it provided higher number of roots/cutting, while the increase in fresh weight of cuttings provided to increase the number of roots/cuttings.

Studies on analgesic, anti-inflammatory activities of stem and roots of Inula cuspidata C.B Clarke

Directory of Open Access Journals (Sweden)

Sarvesh Kumar Paliwal

2017-10-01

Stem and roots were extracted with chloroform (ICSCE, ICRCE and methanol (ICSME, ICRME. Acute oral toxicity of all extracts was determined by OECD guidelines 425. Analgesic activity was investigated by using hot plate and acetic acid induced writhing models. Anti-inflammatory activity (acute of all extracts was evaluated by carrageenan induced paw edema model. In addition, root and stem powder was screened for heavy metals (As, Pb, Cd, Hg estimation using atomic absorption spectroscopy. In acute toxicity study no mortality was observed when each extract was orally administered with 2.0 g/kg. At the doses (100 and 200 mg/kg ICRME followed by ICSME showed significant and dose dependent analgesic and anti-inflammatory effects compared with chloroform extracts. The heavy metals concentration in stem and root powders was found to be within the permissible limits as recommended by WHO for herbal raw materials. The findings of the present study validated the folkloric use of Inula cuspidata as analgesic and anti-inflammatory. In addition, the results intimate that heavy metals present in raw material were found to be within the defined limits, and it exhibits that the therapeutic efficacy of plant may not be effected, which can be otherwise possibly effected if the plant sequester high concentration of heavy metals from the polluted environment as well as from the soil rich in pesticides and sewage sludge etc.

Preparation of tris(8-hydroxyquinolinato)aluminum thin films by sputtering deposition using powder and pressed powder targets

Science.gov (United States)

Kawasaki, Hiroharu; Ohshima, Tamiko; Yagyu, Yoshihito; Ihara, Takeshi; Tanaka, Rei; Suda, Yoshiaki

2017-06-01

Tris(8-hydroxyquinolinato)aluminum (Alq3) thin films, for use in organic electroluminescence displays, were prepared by a sputtering deposition method using powder and pressed powder targets. Experimental results suggest that Alq3 thin films can be prepared using powder and pressed powder targets, although the films were amorphous. The surface color of the target after deposition became dark brown, and the Fourier transform infrared spectroscopy spectrum changed when using a pressed powder target. The deposition rate of the film using a powder target was higher than that using a pressed powder target. That may be because the electron and ion densities of the plasma generated using the powder target are higher than those when using pressed powder targets under the same deposition conditions. The properties of a thin film prepared using a powder target were almost the same as those of a film prepared using a pressed powder target.

Influence of Ultrafine 2CaO·SiO₂ Powder on Hydration Properties of Reactive Powder Concrete.

Science.gov (United States)

Sun, Hongfang; Li, Zishanshan; Memon, Shazim Ali; Zhang, Qiwu; Wang, Yaocheng; Liu, Bing; Xu, Weiting; Xing, Feng

2015-09-17

In this research, we assessed the influence of an ultrafine 2CaO·SiO₂ powder on the hydration properties of a reactive powder concrete system. The ultrafine powder was manufactured through chemical combustion method. The morphology of ultrafine powder and the development of hydration products in the cement paste prepared with ultrafine powder were investigated by scanning electron microscopy (SEM), mineralogical composition were determined by X-ray diffraction, while the heat release characteristics up to the age of 3 days were investigated by calorimetry. Moreover, the properties of cementitious system in fresh and hardened state (setting time, drying shrinkage, and compressive strength) with 5% ordinary Portland cement replaced by ultrafine powder were evaluated. From SEM micrographs, the particle size of ultrafine powder was found to be up to several hundred nanometers. The hydration product started formulating at the age of 3 days due to slow reacting nature of belitic 2CaO·SiO₂. The initial and final setting times were prolonged and no significant difference in drying shrinkage was observed when 5% ordinary Portland cement was replaced by ultrafine powder. Moreover, in comparison to control reactive powder concrete, the reactive powder concrete containing ultrafine powder showed improvement in compressive strength at and above 7 days of testing. Based on above, it can be concluded that the manufactured ultrafine 2CaO·SiO₂ powder has the potential to improve the performance of a reactive powder cementitious system.

Application of laser in powder metallurgy

International Nuclear Information System (INIS)

Tolochko, N.K.

1995-01-01

Modern status of works in the field of laser application in powder metallurgy (powders preparation, sintering, coatings formation, powder materials processing) is considered. The attention is paid to the new promising direction in powder products shape-formation technology - laser layer-by-layer selective powders sintering and bulk sintering of packaged layered profiles produced by laser cutting of powder-based sheet blanks. 67 refs

Automated Root Tracking with "Root System Analyzer"

Science.gov (United States)

Schnepf, Andrea; Jin, Meina; Ockert, Charlotte; Bol, Roland; Leitner, Daniel

2015-04-01

Crucial factors for plant development are water and nutrient availability in soils. Thus, root architecture is a main aspect of plant productivity and needs to be accurately considered when describing root processes. Images of root architecture contain a huge amount of information, and image analysis helps to recover parameters describing certain root architectural and morphological traits. The majority of imaging systems for root systems are designed for two-dimensional images, such as RootReader2, GiA Roots, SmartRoot, EZ-Rhizo, and Growscreen, but most of them are semi-automated and involve mouse-clicks in each root by the user. "Root System Analyzer" is a new, fully automated approach for recovering root architectural parameters from two-dimensional images of root systems. Individual roots can still be corrected manually in a user interface if required. The algorithm starts with a sequence of segmented two-dimensional images showing the dynamic development of a root system. For each image, morphological operators are used for skeletonization. Based on this, a graph representation of the root system is created. A dynamic root architecture model helps to determine which edges of the graph belong to an individual root. The algorithm elongates each root at the root tip and simulates growth confined within the already existing graph representation. The increment of root elongation is calculated assuming constant growth. For each root, the algorithm finds all possible paths and elongates the root in the direction of the optimal path. In this way, each edge of the graph is assigned to one or more coherent roots. Image sequences of root systems are handled in such a way that the previous image is used as a starting point for the current image. The algorithm is implemented in a set of Matlab m-files. Output of Root System Analyzer is a data structure that includes for each root an identification number, the branching order, the time of emergence, the parent

Container for nuclear fuel powders

International Nuclear Information System (INIS)

Etheredge, B.F.; Larson, R.I.

1982-01-01

A critically safe container is disclosed for the storage and rapid discharge of enriched nuclear fuel material in powder form is disclosed. The container has a hollow, slab-shaped container body that has one critically safe dimension. A powder inlet is provided on one side wall of the body adjacent to a corner thereof and a powder discharge port is provided at another corner of the body approximately diagonal the powder inlet. Gas plenum for moving the powder during discharge are located along the side walls of the container adjacent the discharge port

Preparation of superconductor precursor powders

Science.gov (United States)

Bhattacharya, Raghunath

1998-01-01

A process for the preparation of a precursor metallic powder composition for use in the subsequent formation of a superconductor. The process comprises the steps of providing an electrodeposition bath comprising an electrolyte medium and a cathode substrate electrode, and providing to the bath one or more soluble salts of one or more respective metals which are capable of exhibiting superconductor properties upon subsequent appropriate treatment. The bath is continually energized to cause the metallic and/or reduced particles formed at the electrode to drop as a powder from the electrode into the bath, and this powder, which is a precursor powder for superconductor production, is recovered from the bath for subsequent treatment. The process permits direct inclusion of all metals in the preparation of the precursor powder, and yields an amorphous product mixed on an atomic scale to thereby impart inherent high reactivity. Superconductors which can be formed from the precursor powder include pellet and powder-in-tube products.

Influence of Ultrafine 2CaO·SiO2 Powder on Hydration Properties of Reactive Powder Concrete

Directory of Open Access Journals (Sweden)

Hongfang Sun

2015-09-01

Full Text Available In this research, we assessed the influence of an ultrafine 2CaO·SiO2 powder on the hydration properties of a reactive powder concrete system. The ultrafine powder was manufactured through chemical combustion method. The morphology of ultrafine powder and the development of hydration products in the cement paste prepared with ultrafine powder were investigated by scanning electron microscopy (SEM, mineralogical composition were determined by X-ray diffraction, while the heat release characteristics up to the age of 3 days were investigated by calorimetry. Moreover, the properties of cementitious system in fresh and hardened state (setting time, drying shrinkage, and compressive strength with 5% ordinary Portland cement replaced by ultrafine powder were evaluated. From SEM micrographs, the particle size of ultrafine powder was found to be up to several hundred nanometers. The hydration product started formulating at the age of 3 days due to slow reacting nature of belitic 2CaO·SiO2. The initial and final setting times were prolonged and no significant difference in drying shrinkage was observed when 5% ordinary Portland cement was replaced by ultrafine powder. Moreover, in comparison to control reactive powder concrete, the reactive powder concrete containing ultrafine powder showed improvement in compressive strength at and above 7 days of testing. Based on above, it can be concluded that the manufactured ultrafine 2CaO·SiO2 powder has the potential to improve the performance of a reactive powder cementitious system.

Magnetically responsive enzyme powders

Energy Technology Data Exchange (ETDEWEB)

Pospiskova, Kristyna, E-mail: kristyna.pospiskova@upol.cz [Regional Centre of Advanced Technologies and Materials, Palacky University, Slechtitelu 11, 783 71 Olomouc (Czech Republic); Safarik, Ivo, E-mail: ivosaf@yahoo.com [Regional Centre of Advanced Technologies and Materials, Palacky University, Slechtitelu 11, 783 71 Olomouc (Czech Republic); Department of Nanobiotechnology, Institute of Nanobiology and Structural Biology of GCRC, Na Sadkach 7, 370 05 Ceske Budejovice (Czech Republic)

2015-04-15

Powdered enzymes were transformed into their insoluble magnetic derivatives retaining their catalytic activity. Enzyme powders (e.g., trypsin and lipase) were suspended in various liquid media not allowing their solubilization (e.g., saturated ammonium sulfate and highly concentrated polyethylene glycol solutions, ethanol, methanol, 2-propanol) and subsequently cross-linked with glutaraldehyde. Magnetic modification was successfully performed at low temperature in a freezer (−20 °C) using magnetic iron oxides nano- and microparticles prepared by microwave-assisted synthesis from ferrous sulfate. Magnetized cross-linked enzyme powders were stable at least for two months in water suspension without leakage of fixed magnetic particles. Operational stability of magnetically responsive enzymes during eight repeated reaction cycles was generally without loss of enzyme activity. Separation of magnetically modified cross-linked powdered enzymes from reaction mixtures was significantly simplified due to their magnetic properties. - Highlights: • Cross-linked enzyme powders were prepared in various liquid media. • Insoluble enzymes were magnetized using iron oxides particles. • Magnetic iron oxides particles were prepared by microwave-assisted synthesis. • Magnetic modification was performed under low (freezing) temperature. • Cross-linked powdered trypsin and lipase can be used repeatedly for reaction.

Sintered aluminium powders

International Nuclear Information System (INIS)

Stepanova, M.G.; Matveev, B.I.

1974-01-01

The mechanical and physical properties of aluminium powder alloys and the various methods employed to produce them are considered. Data are given on the hardening of the alloys SAP and SPAK-4, as well as the powder-alloy system Al-Cr-Zr. (L.M.)

Powder diffraction

Energy Technology Data Exchange (ETDEWEB)

Hart, M.

1995-12-31

the importance of x-ray powder diffraction as an analytical tool for phase identification of materials was first pointed out by Debye and Scherrer in Germany and, quite independently, by Hull in the US. Three distinct periods of evolution lead to ubiquitous application in many fields of science and technology. In the first period, until the mid-1940`s, applications were and developed covering broad categories of materials including inorganic materials, minerals, ceramics, metals, alloys, organic materials and polymers. During this formative period, the concept of quantitative phase analysis was demonstrated. In the second period there followed the blossoming of technology and commercial instruments became widely used. The history is well summarized by Parrish and by Langford and Loueer. By 1980 there were probably 10,000 powder diffractometers in routine use, making it the most widely used of all x-ray crystallographic instruments. In the third, present, period data bases became firmly established and sophisticated pattern fitting and recognition software made many aspects of powder diffraction analysis routine. High resolution, tunable powder diffractometers were developed at sources of synchrotron radiation. The tunability of the spectrum made it possible to exploit all the subtleties of x-ray spectroscopy in diffraction experiments.

Powder diffraction

International Nuclear Information System (INIS)

Hart, M.

1995-01-01

The importance of x-ray powder diffraction as an analytical tool for phase identification of materials was first pointed out by Debye and Scherrer in Germany and, quite independently, by Hull in the US. Three distinct periods of evolution lead to ubiquitous application in many fields of science and technology. In the first period, until the mid-1940's, applications were and developed covering broad categories of materials including inorganic materials, minerals, ceramics, metals, alloys, organic materials and polymers. During this formative period, the concept of quantitative phase analysis was demonstrated. In the second period there followed the blossoming of technology and commercial instruments became widely used. The history is well summarized by Parrish and by Langford and Loueer. By 1980 there were probably 10,000 powder diffractometers in routine use, making it the most widely used of all x-ray crystallographic instruments. In the third, present, period data bases became firmly established and sophisticated pattern fitting and recognition software made many aspects of powder diffraction analysis routine. High resolution, tunable powder diffractometers were developed at sources of synchrotron radiation. The tunability of the spectrum made it possible to exploit all the subtleties of x-ray spectroscopy in diffraction experiments

Method to blend separator powders

Science.gov (United States)

Guidotti, Ronald A.; Andazola, Arthur H.; Reinhardt, Frederick W.

2007-12-04

A method for making a blended powder mixture, whereby two or more powders are mixed in a container with a liquid selected from nitrogen or short-chain alcohols, where at least one of the powders has an angle of repose greater than approximately 50 degrees. The method is useful in preparing blended powders of Li halides and MgO for use in the preparation of thermal battery separators.

Inactivation of local root canal medicaments by dentine: an in vitro study.

Science.gov (United States)

Haapasalo, H K; Sirén, E K; Waltimo, T M; Ørstavik, D; Haapasalo, M P

2000-03-01

The aim of the study was to investigate the inactivation by dentine of the antibacterial activity of various commonly used local root canal medicaments. The medicaments tested were saturated calcium hydroxide solution, 1% sodium hypochlorite, 0.5% and 0.05% chlorhexidine acetate, and 2/4% and 0.2/0.4% iodine potassium iodide. Dentine was sterilized by autoclaving and crushed into powder with a particle size of 0.2-20 microns. Aliquots of dentine suspension were incubated with the medicaments in sealed test tubes at 37 degrees C for 24 h or 1 h before adding the bacteria. In some experiments bacteria were added simultaneously with dentine powder and the medicament. Enterococcus faecalis A197A was used as a test organism. Samples for bacterial culturing were taken from the suspensions at 5 min, 1 h and 24 h after adding the bacteria. Dentine powder had an inhibitory effect on all medicaments tested. The effect was dependent on the concentration of the medicament as well as on the length of the time the medicament was preincubated with dentine powder before adding the bacteria. The effect of calcium hydroxide on E. faecalis was totally abolished by the presence of dentine powder. Similarly, 0.2/0.4% iodine potassium iodide lost its effect after preincubation for 1 h with dentine before adding the bacteria. The effect of 0.05% chlorhexidine and 1% sodium hypochlorite on E. faecalis was reduced but not totally eliminated by the presence of dentine. No inhibition could be measured when full strength solutions of chlorhexidine and iodine potassium iodide were used in killing E. faecalis. The dentine powder model appears to be an efficient tool for the study of interactions between local endodontic medicaments, dentine, and microbes.

Molybdenum plasma spray powder, process for producing said powder, and coating made therefrom

International Nuclear Information System (INIS)

Lafferty, W.D.; Cheney, R.F.; Pierce, R.H.

1979-01-01

Plasma spray powders of molybdenum particles containing 0.5 to 15 weight percent oxygen and obtained by reacting molybdenum particles with oxygen or oxides in a plasma, form plasma spray coatings exhibiting hardness comparable to flame sprayed coatings formed from molybdenum wire and plasma coatings of molybdenum powders. Such oxygen rich molybdenum powders may be used to form wear resistant coatings, such as for piston rings. (author)

SAF line powder operations

International Nuclear Information System (INIS)

Frederickson, J.R.; Horgos, R.M.

1983-10-01

An automated nuclear fuel fabrication line is being designed for installation in the Fuels and Materials Examination Facility (FMEF) near Richland, Washington. The fabrication line will consist of seven major process systems: Receiving and Powder Preparation; Powder Conditioning; Pressing and Boat Loading; Debinding, Sintering, and Property Adjustment; Boat Transport; Pellet Inspection and Finishing; and Pin Operations. Fuel powder processing through pellet pressing will be discussed in this paper

Two layer powder pressing

International Nuclear Information System (INIS)

Schreiner, H.

1979-01-01

First, significance and advantages of sintered materials consisting of two layers are pointed out. By means of the two layer powder pressing technique metal powders are formed resulting in compacts with high accuracy of shape and mass. Attributes of basic powders, different filling methods and pressing techniques are discussed. The described technique is supposed to find further applications in the field of two layer compacts in the near future

Sonication, Vacuum Infiltration and Thiol Compounds Enhance the Agrobacterium-Mediated Transformation Frequency of Withania somnifera (L.) Dunal

Science.gov (United States)

Sivanandhan, Ganeshan; Kapil Dev, Gnajothi; Theboral, Jeevaraj; Selvaraj, Natesan; Ganapathi, Andy; Manickavasagam, Markandan

2015-01-01

In the present study, we have established a stable transformation protocol via Agrobacterium tumafacines for the pharmaceutically important Withania somnifera. Six day-old nodal explants were used for 3 day co-cultivation with Agrobacterium tumefaciens strain LBA4404 harbouring the vector pCAMIBA2301. Among the different injury treatments, sonication, vacuum infiltration and their combination treatments tested, a vacuum infiltration for 10 min followed by sonication for 10 sec with A. tumefaciens led to a higher transient GUS expression (84% explants expressing GUS at regenerating sites). In order to improve gene integration, thiol compounds were added to co-cultivation medium. A combined treatment of L-Cys at 100 mg/l, STS at 125 mg/l, DTT at 75 mg/l resulted in a higher GUS expression (90%) in the nodal explants. After 3 days of co-cultivation, the explants were subjected to three selection cycles with increasing concentrations of kanamycin [100 to 115 mg/l]. The integration and expression of gusA gene in T0 and T1 transgenic plants were confirmed by polymerase chain reaction (PCR), and Southern blott analysis. These transformed plants (T0 and T1) were fertile and morphologically normal. From the present investigation, we have achieved a higher transformation efficiency of (10%). Withanolides (withanolide A, withanolide B, withanone and withaferin A) contents of transformed plants (T0 and T1) were marginally higher than control plants. PMID:25927703

The analysis of powder diffraction data

International Nuclear Information System (INIS)

David, W.I.F.; Harrison, W.T.A.

1986-01-01

The paper reviews neutron powder diffraction data analysis, with emphasis on the structural aspects of powder diffraction and the future possibilities afforded by the latest generation of very high resolution neutron and x-ray powder diffractometers. Traditional x-ray powder diffraction techniques are outlined. Structural studies by powder diffraction are discussed with respect to the Rietveld method, and a case study in the Rietveld refinement method and developments of the Rietveld method are described. Finally studies using high resolution powder diffraction at the Spallation Neutron Source, ISIS at the Rutherford Appleton Laboratory are summarized. (U.K.)

Roller compaction of moist pharmaceutical powders.

Science.gov (United States)

Wu, C-Y; Hung, W-L; Miguélez-Morán, A M; Gururajan, B; Seville, J P K

2010-05-31

The compression behaviour of powders during roller compaction is dominated by a number of factors, such as process conditions (roll speed, roll gap, feeding mechanisms and feeding speed) and powder properties (particle size, shape, moisture content). The moisture content affects the powder properties, such as the flowability and cohesion, but it is not clear how the moisture content will influence the powder compression behaviour during roller compaction. In this study, the effect of moisture contents on roller compaction behaviour of microcrystalline cellulose (MCC, Avicel PH102) was investigated experimentally. MCC samples of different moisture contents were prepared by mixing as-received MCC powder with different amount of water that was sprayed onto the powder bed being agitated in a rotary mixer. The flowability of these samples were evaluated in terms of the poured angle of repose and flow functions. The moist powders were then compacted using the instrumented roller compactor developed at the University of Birmingham. The flow and compression behaviour during roller compaction and the properties of produced ribbons were examined. It has been found that, as the moisture content increases, the flowability of moist MCC powders decreases and the powder becomes more cohesive. As a consequence of non-uniform flow of powder into the compaction zone induced by the friction between powder and side cheek plates, all produced ribbons have a higher density in the middle and lower densities at the edges. For the ribbons made of powders with high moisture contents, different hydration states across the ribbon width were also identified from SEM images. Moreover, it was interesting to find that these ribbons were split into two halves. This is attributed to the reduction in the mechanical strength of moist powder compacts with high moisture contents produced at high compression pressures. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Black powder in gas pipelines

Energy Technology Data Exchange (ETDEWEB)

Sherik, Abdelmounam [Saudi Aramco, Dhahran (Saudi Arabia)

2009-07-01

Despite its common occurrence in the gas industry, black powder is a problem that is not well understood across the industry, in terms of its chemical and physical properties, source, formation, prevention or management of its impacts. In order to prevent or effectively manage the impacts of black powder, it is essential to have knowledge of its chemical and physical properties, formation mechanisms and sources. The present paper is divided into three parts. The first part of this paper is a synopsis of published literature. The second part reviews the recent laboratory and field work conducted at Saudi Aramco Research and Development Center to determine the compositions, properties, sources and formation mechanisms of black powder in gas transmission systems. Microhardness, nano-indentation, X-ray Diffraction (XRD), X-ray Fluorescence (XRF) and Scanning Electron Microscopy (SEM) techniques were used to analyze a large number of black powder samples collected from the field. Our findings showed that black powder is generated inside pipelines due to internal corrosion and that the composition of black powder is dependent on the composition of transported gas. The final part presents a summary and brief discussion of various black powder management methods. (author)

Rapid analysis of adulterations in Chinese lotus root powder (LRP) by near-infrared (NIR) spectroscopy coupled with chemometric class modeling techniques.

Science.gov (United States)

Xu, Lu; Shi, Peng-Tao; Ye, Zi-Hong; Yan, Si-Min; Yu, Xiao-Ping

2013-12-01

This paper develops a rapid analysis method for adulteration identification of a popular traditional Chinese food, lotus root powder (LRP), by near-infrared spectroscopy and chemometrics. 85 pure LRP samples were collected from 7 main lotus producing areas of China to include most if not all of the significant variations likely to be encountered in unknown authentic materials. To evaluate the model specificity, 80 adulterated LRP samples prepared by blending pure LRP with different levels of four cheaper and commonly used starches were measured and predicted. For multivariate quality models, two class modeling methods, the traditional soft independent modeling of class analogy (SIMCA) and a recently proposed partial least squares class model (PLSCM) were used. Different data preprocessing techniques, including smoothing, taking derivative and standard normal variate (SNV) transformation were used to improve the classification performance. The results indicate that smoothing, taking second-order derivatives and SNV can improve the class models by enhancing signal-to-noise ratio, reducing baseline and background shifts. The most accurate and stable models were obtained with SNV spectra for both SIMCA (sensitivity 0.909 and specificity 0.938) and PLSCM (sensitivity 0.909 and specificity 0.925). Moreover, both SIMCA and PLSCM could detect LRP samples mixed with 5% (w/w) or more other cheaper starches, including cassava, sweet potato, potato and maize starches. Although it is difficult to perform an exhaustive collection of all pure LRP samples and possible adulterations, NIR spectrometry combined with class modeling techniques provides a reliable and effective method to detect most of the current LRP adulterations in Chinese market. Copyright © 2013 Elsevier Ltd. All rights reserved.

Thermal plasma spheroidization and spray deposition of barium titanate powder and characterization of the plasma sprayable powder

Energy Technology Data Exchange (ETDEWEB)

Pakseresht, A.H., E-mail: amirh_pak@yahoo.com [Department of Ceramics, Materials and Energy Research Center, P.O. Box 31787-316, Karaj (Iran, Islamic Republic of); Rahimipour, M.R. [Department of Ceramics, Materials and Energy Research Center, P.O. Box 31787-316, Karaj (Iran, Islamic Republic of); Vaezi, M.R. [Department of Nanotechnology and Advanced Materials, Materials and Energy Research Center, P.O. Box 31787-316, Karaj (Iran, Islamic Republic of); Salehi, M. [Department of Materials Engineering, Isfahan University of Technology, P.O. Box 84156-83111, Isfahan (Iran, Islamic Republic of)

2016-04-15

In this paper, atmospheric plasma spray method was used to produce dense plasma sprayable powder and thick barium titanate film. In this regard, the commercially feedstock powders were granulated and spheroidized by the organic binder and the thermal spray process, respectively. Scanning electron microscopy was used to investigate the microstructure of the produced powders and the final deposits. X-ray diffraction was also implemented to characterize phase of the sprayed powder. The results indicated that spheroidized powder had suitable flowability as well as high density. The micro-hardness of the film produced by the sprayed powders was higher than that of the film deposited by the irregular granules. Additionally, relative permittivity of the films was increased by decreasing the defects from 160 to 293 for film deposited using spheroidized powder. The reduction in the relative permittivity of deposits, in comparison with the bulk material, was due to the existence of common defects in the thermal spray process. - Highlights: • We prepare sprayable BaTiO{sub 3} powder with no or less inside voids for plasma spray application for first time. • The sprayable powder has good flow characteristics and high density. • Powder spheroidization via plasma spray improves the hardness and dielectric properties of the deposited film.

Thermal plasma spheroidization and spray deposition of barium titanate powder and characterization of the plasma sprayable powder

International Nuclear Information System (INIS)

Pakseresht, A.H.; Rahimipour, M.R.; Vaezi, M.R.; Salehi, M.

2016-01-01

In this paper, atmospheric plasma spray method was used to produce dense plasma sprayable powder and thick barium titanate film. In this regard, the commercially feedstock powders were granulated and spheroidized by the organic binder and the thermal spray process, respectively. Scanning electron microscopy was used to investigate the microstructure of the produced powders and the final deposits. X-ray diffraction was also implemented to characterize phase of the sprayed powder. The results indicated that spheroidized powder had suitable flowability as well as high density. The micro-hardness of the film produced by the sprayed powders was higher than that of the film deposited by the irregular granules. Additionally, relative permittivity of the films was increased by decreasing the defects from 160 to 293 for film deposited using spheroidized powder. The reduction in the relative permittivity of deposits, in comparison with the bulk material, was due to the existence of common defects in the thermal spray process. - Highlights: • We prepare sprayable BaTiO_3 powder with no or less inside voids for plasma spray application for first time. • The sprayable powder has good flow characteristics and high density. • Powder spheroidization via plasma spray improves the hardness and dielectric properties of the deposited film.

Ceramic Inclusions In Powder Metallurgy Disk Alloys: Characterization and Modeling

Science.gov (United States)

Bonacuse, Pete; Kantzos, Pete; Telesman, Jack

2002-01-01

Powder metallurgy alloys are increasingly used in gas turbine engines, especially as the material chosen for turbine disks. Although powder metallurgy materials have many advantages over conventionally cast and wrought alloys (higher strength, higher temperature capability, etc.), they suffer from the rare occurrence of ceramic defects (inclusions) that arise from the powder atomization process. These inclusions can have potentially large detrimental effect on the durability of individual components. An inclusion in a high stress location can act as a site for premature crack initiation and thereby considerably reduce the fatigue life. Because these inclusions are exceedingly rare, they usually don't reveal themselves in the process of characterizing the material for a particular application (the cumulative volume of the test bars in a fatigue life characterization is typically on the order of a single actual component). Ceramic inclusions have, however, been found to be the root cause of a number of catastrophic engine failures. To investigate the effect of these inclusions in detail, we have undertaken a study where a known population of ceramic particles, whose composition and morphology are designed to mimic the 'natural' inclusions, are added to the precursor powder. Surface connected inclusions have been found to have a particularly large detrimental effect on fatigue life, therefore the volume of ceramic 'seeds' added is calculated to ensure that a minimum number will occur on the surface of the fatigue test bars. Because the ceramic inclusions are irregularly shaped and have a tendency to break up in the process of extrusion and forging, a method of calculating the probability of occurrence and expected intercepted surface and embedded cross-sectional areas were needed. We have developed a Monte Carlo simulation to determine the distributions of these parameters and have verified the simulated results with observations of ceramic inclusions found in macro

Comparative in silico analyses of Cannabis sativa, Prunella vulgaris and Withania somnifera compounds elucidating the medicinal properties against rheumatoid arthritis.

Science.gov (United States)

Zaka, Mehreen; Sehgal, Sheikh Arslan; Shafique, Shagufta; Abbasi, Bilal Haider

2017-06-01

From last decade, there has been progressive improvement in computational drug designing. Several diseases are being cured from different plant extracts and products. Rheumatoid Arthritis (RA) is the most shared disease among auto-inflammatory diseases. Tumour necrosis factor (TNF)-α is associated with RA pathway and has adverse effects. Extensive literature review showed that plant species under study (Cannabis sativa, Prunella vulgaris and Withania somnifera) possess anti-inflammatory, anti-arthritic and anti-rheumatic properties. 13 anti-inflammatory compounds were characterised and filtered out from medicinal plant species and analysed for RA by targeting TNF-α through in silico analyses. By using ligand based pharmacophore generation approach and virtual screening against natural products libraries we retrieved twenty unique molecules that displayed utmost binding affinity, least binding energies and effective drug properties. The docking analyses revealed that Ala-22, Glu-23, Ser-65, Gln-67, Tyr-141, Leu-142, Asp-143, Phe-144 and Ala-145 were critical interacting residues for receptor-ligand interactions. It is proposed that the RA patients should use reported compounds for the prescription of RA by targeting TNF-α. This report is opening new dimensions for designing innovative therapeutic targets to cure RA. Copyright © 2017 Elsevier Inc. All rights reserved.

Weighing fluidized powder

International Nuclear Information System (INIS)

Adomitis, J.T.; Larson, R.I.

1980-01-01

Fluidized powder is discharged from a fluidizing vessel into a container. Accurate metering is achieved by opening and closing the valve to discharge the powder in a series of short-duration periods until a predetermined weight is measured by a load cell. The duration of the discharge period may be increased in inverse proportion to the amount of powder in the vessel. Preferably the container is weighed between the discharge periods to prevent fluctuations resulting from dynamic effects. The gas discharged into the container causes the pressures in the vessel and container to equalize thereby decreasing the rate of discharge and increasing the accuracy of metering as the weight reaches the predetermined value. (author)

21 CFR 73.1647 - Copper powder.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Copper powder. 73.1647 Section 73.1647 Food and... ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1647 Copper powder. (a) Identity. (1) The color additive copper powder is a very fine free-flowing metallic powder prepared from virgin electrolytic copper. It...

[Use of powder metallurgy for development of implants of Co-Cr-Mo alloy powder].

Science.gov (United States)

Dabrowski, J R

2001-04-01

This paper discusses the application of powder metallurgy for the development of porous implantation materials. Powders obtained from Co-Cr-Mo alloy with different carbon content by water spraying and grinding, have been investigated. Cold pressing and rotary re-pressing methods were used for compressing the powder. It was found that the sintered materials obtained from water spraying have the most advantageous properties.

Reducing metal alloy powder costs for use in powder bed fusion additive manufacturing: Improving the economics for production

Science.gov (United States)

Medina, Fransisco

Titanium and its associated alloys have been used in industry for over 50 years and have become more popular in the recent decades. Titanium has been most successful in areas where the high strength to weight ratio provides an advantage over aluminum and steels. Other advantages of titanium include biocompatibility and corrosion resistance. Electron Beam Melting (EBM) is an additive manufacturing (AM) technology that has been successfully applied in the manufacturing of titanium components for the aerospace and medical industry with equivalent or better mechanical properties as parts fabricated via more traditional casting and machining methods. As the demand for titanium powder continues to increase, the price also increases. Titanium spheroidized powder from different vendors has a price range from 260/kg-450/kg, other spheroidized alloys such as Niobium can cost as high as $1,200/kg. Alternative titanium powders produced from methods such as the Titanium Hydride-Dehydride (HDH) process and the Armstrong Commercially Pure Titanium (CPTi) process can be fabricated at a fraction of the cost of powders fabricated via gas atomization. The alternative powders can be spheroidized and blended. Current sectors in additive manufacturing such as the medical industry are concerned that there will not be enough spherical powder for production and are seeking other powder options. It is believed the EBM technology can use a blend of spherical and angular powder to build fully dense parts with equal mechanical properties to those produced using traditional powders. Some of the challenges with angular and irregular powders are overcoming the poor flow characteristics and the attainment of the same or better packing densities as spherical powders. The goal of this research is to demonstrate the feasibility of utilizing alternative and lower cost powders in the EBM process. As a result, reducing the cost of the raw material to reduce the overall cost of the product produced with

Effect of endophytic pseudomonas aeruinosa and trichoderma harzianum on soil-borne diseases, mycorrhizae and induction of systemic resistance in okra grown in soil amended with vernonia anthelmintica (L.) seeds powder

International Nuclear Information System (INIS)

Shafique, H. A.; Noreen, R.; Haque, S. E. U.; Sultana, V.; Ara, J.

2015-01-01

Biostimulants are used in agricultural practices for plant growth improvement. These fertilizers improve microbial activity and cause a negative impact on soil-borne pathogens. In recent years, stimulating plant natural defense is considered as most promising alternative strategy for crop productivity. The present study was carried out to examine the effect of endophytic Pseudomonas aeruginosa and Trichoderma harzianum in soil amendment with Vernonia anthelmintica seeds powder, on root rotting fungi, plant growth, mycorrhizal population around roots, phosphorous uptake and stimulation of plant defense markers like poylphenol and antioxidant status in okra. Combine application of Vernonia with Pseudomonas aeruginosa and Trichoderma harzianum significantly (p<0.05) suppressed Rhizoctonia solani and Fusarium oxysporum with complete reduction of Macrophomina phaseolina and Fusarium solani. Pseudomonas aeruginosa and T. harzianum alone or in Vernonia amended soil significantly reduced nematode galls on roots. Organic amendment also improved plant resistance against root diseases as evident from enhanced DPPH radical scavenging capacity and polyphenol content in treated plants as compare to control. VA Mycorrhizal spores were found significantly (p<0.05) higher in number around roots received Pseudomonas aeruginosa or T. harzianum alone or in Vernonia amended soil. Whereas, higher concentrations of phosphorus in okra shoots were found in plants received biocontrol agents in amended soil. Mixed application of PGPR and T. harzianum in amended soil produced tallest plants than other treatments. Soil amendment with Vernonia seed powder alone or with biocontrol agents offer a non-chemical means of plant disease control. (author)

PHYTOCHEMICAL ANALYSIS OF HYDROETHANOLIC EXTRACTS FROM POWDERED ROOTS OF Panax ginseng C. A. Meyer AND Heteropterys tomentosa A. Juss AND EVALUATION OF THEIR EFFECTS ON ASTROCYTE CELL DEATH

Directory of Open Access Journals (Sweden)

Andréia Gomes Bezerra

2016-06-01

Full Text Available The medicinal plants Panax ginseng C. A. Meyer (Araliaceae and Heteropterys tomentosa A. Juss (Malpighiaceae are widely and separately used by the Brazilian population as phytotherapeutics for the same medicinal purposes as tonics and to improve cognition. A chemical analysis was carried out on hydroethanolic extracts of powdered roots from P. ginseng and H. tomentosa using HPLC-DAD-ESI-MS/MS (High Performance Liquid Chromatography coupled to Diode-Array Detector and Electrospray Ionization - Mass Spectrum/Mass Spectrum. The ginsenosides Rg1, Rf, mRg and mRf were the main constituents in a hydroethanolic extract from P. ginseng, while in the hydroethanolic extract from H. tomentosa, caffeoylquinic acid derivatives and astilbin isomers were the main constituents. Concentration-time-effect curves were generated in cultures of astrocytes that were incubated with hydroethanolic extracts of these species to elucidate their toxicities. The P. ginseng extract was nontoxic at all of the tested times and concentrations. The hydroethanolic extract from H. tomentosa demonstrated toxicity at a concentration of 1000 µg/mL. P. ginseng extract had no protective effect against staurosporine. Many studies have demonstrated the neuroprotective effect of ginsenosides, caffeoylquinic derivatives and flavonoids.

Crushing method for nuclear fuel powder

International Nuclear Information System (INIS)

Hasegawa, Shin-ichi; Tsuchiya, Haruo.

1997-01-01

A crushing medium is contained in mill pots disposed at the circumferential periphery of a main axis. The diameter of each mill pot is determined such that powdery nuclear fuels containing aggregated powders and ground and mixed powders do not reach criticality. A plurality of mill pots are revolved in the direction of the main axis while each pots rotating on its axis. Powdery nuclear fuels containing aggregated powders are conveyed to a supply portion of the moll pot, and an inert gas is supplied to the supply portion. The powdery nuclear fuels are supplied from the supply portion to the inside of the mill pots, and the powdery nuclear fuels containing aggregated powders are crushed by centrifugal force caused by the rotation and the revolving of the mill pots by means of the crushing medium. UO 2 powder in uranium oxide fuels can be crushed continuously. PuO 2 powder and UO 2 powder in MOX fuels can be crushed and mixed continuously. (I.N.)

Ultrafine hydrogen storage powders

Science.gov (United States)

Anderson, Iver E.; Ellis, Timothy W.; Pecharsky, Vitalij K.; Ting, Jason; Terpstra, Robert; Bowman, Robert C.; Witham, Charles K.; Fultz, Brent T.; Bugga, Ratnakumar V.

2000-06-13

A method of making hydrogen storage powder resistant to fracture in service involves forming a melt having the appropriate composition for the hydrogen storage material, such, for example, LaNi.sub.5 and other AB.sub.5 type materials and AB.sub.5+x materials, where x is from about -2.5 to about +2.5, including x=0, and the melt is gas atomized under conditions of melt temperature and atomizing gas pressure to form generally spherical powder particles. The hydrogen storage powder exhibits improved chemcial homogeneity as a result of rapid solidfication from the melt and small particle size that is more resistant to microcracking during hydrogen absorption/desorption cycling. A hydrogen storage component, such as an electrode for a battery or electrochemical fuel cell, made from the gas atomized hydrogen storage material is resistant to hydrogen degradation upon hydrogen absorption/desorption that occurs for example, during charging/discharging of a battery. Such hydrogen storage components can be made by consolidating and optionally sintering the gas atomized hydrogen storage powder or alternately by shaping the gas atomized powder and a suitable binder to a desired configuration in a mold or die.

Electrochemical behaviors of wax-coated Li powder/Li 4Ti 5O 12 cells

Science.gov (United States)

Park, Han Eol; Seong, Il Won; Yoon, Woo Young

The wax-coated Li powder specimen was effectively synthesized using the drop emulsion technique (DET). The wax layer on the powder was verified by SEM, Focused Ion Beam (FIB), EDX and XPS. The porosity of a sintered wax-coated Li electrode was measured by linear sweep voltammetry (LSV) and compared with that of a bare, i.e., un-coated Li electrode. The electrochemical behavior of the wax-coated Li powder anode cell was examined by the impedance analysis and cyclic testing methods. The cyclic behavior of the wax-coated Li powder anode with the Li 4Ti 5O 12 (LTO) cathode cell was examined at a constant current density of 0.35 mA cm -2 with the cut-off voltages of 1.2-2.0 V at 25 °C. Over 90% of the initial capacity of the cell remained even after the 300th cycle. The wax-coated Li powder was confirmed to be a stable anode material.

Exploratory study to evaluate tolerability, safety, and activity of Ashwagandha (Withania somnifera in healthy volunteers

Directory of Open Access Journals (Sweden)

Ashwinikumar A Raut

2012-01-01

Full Text Available Ashwagandha (Withania somnifera (WS, a "rasayana" drug, is recommended for balavardhan and mamsavardhan. The study was intended to evaluate dose-related tolerability, safety, and activity of WS formulation in normal individuals. The design was prospective, open-labeled, variable doses in volunteers. Eighteen apparently healthy volunteers (12M:6F, age:18-30 years, and BMI: 19-30 were enrolled. After baseline investigations, they received WS capsules (Rx (aqueous extract, 8:1 daily in two divided doses with increase in daily dosage every 10 days for 30 days (750 mg/day x10 days, 1 000 mg/day x 10 days, 1 250 mg/day x 10 days. Volunteers were assessed for symptoms/signs, vital functions, hematological and biochemical organ function tests. Muscle activity was measured by hand grip strength, quadriceps strength, and back extensor force. Exercise tolerance was determined using cycle ergometry. Lean body weight and fat% were computed from skin fold thickness measurement. Adverse events were recorded, as volunteered by the subjects. Repeated measures ANOVA, McNemar′s test, and paired t test were employed. All but one volunteer tolerated WS without any adverse event. One volunteer showed increased appetite, libido, and hallucinogenic effects with vertigo at the lowest dose and was withdrawn from study. In six subjects, improvement in quality of sleep was found. Organ function tests were in normal range before and after the intervention. Reduction in total- and LDL- cholesterol and increase of strength in muscle activity was significant. Total body fat percentage showed a reduction trend. WS, in escalated dose, was tolerated well. The formulation appeared safe and strengthened muscle activity. In view of its traditional Rasayana use, further studies are planned to evaluate potential of this drug in patients of sarcopenia.

Study of Velocity and Materials on Tribocharging of Polymer Powders for Powder Coating Applications

Science.gov (United States)

Biris, Alex S.; Trigwell, Steve; Sims, Robert A.; Mazumder, Malay K.

2005-01-01

Electrostatic powder deposition is widely used in a plethora of industrial-applications ranging from the pharmaceutical and food.industries, to farm equipment and automotive applications. The disadvantages of this technique are possible back corona (pin-like formations) onset and the Faraday penetration limitation (when the powder does not penetrate in some recessed areas). A possible solution to overcome these problems is to use tribochargers to electrostatically charge the powder. Tribocharging, or contact charging while two materials are in contact, is related to the work function difference between the contacting materials and generates bipolarly charged particles. The generation of an ion-free powder cloud by tribocharging with high bipolar charge and an overall charge density of almost zero, provides a better coverage of the recessed areas. In this study, acrylic and epoxy powders were fluidized and charged by passing through stainless steel, copper, aluminum, and polycarbonate static mixers, respectively. The particle velocity was varied to determine its effect on the net charge-to-mass ratio (QIM) acquired by the powders. In general, the Q/M increases rapidly when the velocity was increased from 1.5 to 2.5 m/s, remaining almost constant for higher velocities. Charge separation experiments showed bipolar charging for all chargers.

Cytotoxicity of 5% Tamarindus indica extract and 3% hydrogen peroxide as root canal irrigation

Directory of Open Access Journals (Sweden)

Erawati Wulandari

2008-09-01

Full Text Available Background: Preparation of root canal is an important stage in endodontic treatment. During conducting preparation, it is always be followed with root canal irrigation that has aim to clean root canal from necrotic tissue remains, grind down dentin powder, micro organism, wet the root canal to make preparation process of root canal easier, and solute root canal content at area that can not be reached by equipment. Flesh of Tamarindus indica (pulpa tamarindorum is used as traditional medicine and it contains vitamin C (antioxidant, protein, fat, glucose, etc. Previous research shows that 5% tamarindus indica extract can clean smear layer but it is more cytotoxicity to cell line BHK–21 than sterilized aquabides. Purpose: This research is to compare cytotoxicity between 5% Tamarindus indica extract with 3% H2O2 as root canal irrigation material. Method: Four teen culture cell line BHK 21 divides into 2 groups. Group 1 is treated with 3% H2O2 and Group 2 is treated with 5% Tamarindus indica extract, for about 2.5 minutes in every group. Then, living and death cell percentage is measured. Data is analyzed with independent t test with significant level of 0.05%. Result: The research showed that death cell in group 1 was 29.3% and in group 2 was 21.1%. There was a significant different (p < 0.05 between group 1 and group 2. Conclusion: Cytotoxicity of 5% Tamarindus indica extract to the cell line BHK–21 is lower than 3% H2O2.

Coal Waste Powder Amendment and Arbuscular Mycorrhizal Fungi Enhance the Growth of Jabon (Anthocephalus cadamba Miq Seedling in Ultisol Soil Medium

Directory of Open Access Journals (Sweden)

Sri Wilarso Budi

2013-03-01

Full Text Available Coal powder waste application on low nutrient media is expected to be able to increase plant growth and to improve Arbuscular mycorrhizal fungi (AMF development. The objective of this research was to determine the effect of coal waste powder on the growth of Anthocephallus cadamba Jack and AMF development grown on ultisol soil. Two factors in a completely randomised experimental design was conducted under greenhouse conditions and Duncan Multiple Range Test was used to analyse of the effect the treatment. The first factor was ultisol soil ammended with coal waste powder (control, soil amanded with coal waste 5%, soil amanded with coal waste 10% and soil amanded with coal waste 15% and the second factor was AMF inoculation (uninoculated control, inoculated with Gigaspora margarita. Plant height, diameter, shoot dry weight, percentage of AMF colonization and nutrient uptake were measured in this experiment. Results of this study showed that coal amendment and AMF when applied separately significantly increased height, diameter, shoot dry weight, root dry weight and nutrient uptake of 12 weeks A. cadamba seedling, but when the coal waste powder and AMF were combined the plant growth parameters were lower than those applied separately but significantly higher than control. The application of coal waste powder or AMF in ultisol soil could increase A. cadamba growth and development.

Plasma technology for powder particles

Energy Technology Data Exchange (ETDEWEB)

Kranz, E. (Technische Hochschule, Ilmenau (German Democratic Republic))

1983-03-01

A survey is given of principles and applications of plasma spraying and of powder transformation and generation in plasma considering spheroidization, grain size transformation, powder particle formation, powder reduction, and melting within the power range of 10/sup 3/ to 10/sup 7/ W. The products are applied in many industrial fields such as nuclear engineering, hard metal production, metallurgy, catalysis, and semiconductor techniques.

Inhibitory potency of Withania somnifera extracts against DPP-4: an ...

African Journals Online (AJOL)

Materials and Methods: Young and matured fresh roots, leaves, and fruits of WS plant extract were considered and were systematically evaluated for DPP-4 inhibitory activity using in vitro method, enzyme kinetics, phytochemical analysis, RP-HPLC, LCMS and 1H and 13C NMR method and structure-activity relationship ...

Water extract from the leaves of Withania somnifera protect RA differentiated C6 and IMR-32 cells against glutamate-induced excitotoxicity.

Directory of Open Access Journals (Sweden)

Hardeep Kataria

Full Text Available Glutamate neurotoxicity has been implicated in stroke, head trauma, multiple sclerosis and neurodegenerative disorders. Search for herbal remedies that may possibly act as therapeutic agents is an active area of research to combat these diseases. The present study was designed to investigate the neuroprotective role of Withania somnifera (Ashwagandha, also known as Indian ginseng, against glutamate induced toxicity in the retinoic acid differentiated rat glioma (C6 and human neuroblastoma (IMR-32 cells. The neuroprotective activity of the Ashwagandha leaves derived water extract (ASH-WEX was evaluated. Cell viability and the expression of glial and neuronal cell differentiation markers was examined in glutamate challenged differentiated cells with and without the presence of ASH-WEX. We demonstrate that RA-differentiated C6 and IMR-32 cells, when exposed to glutamate, undergo loss of neural network and cell death that was accompanied by increase in the stress protein HSP70. ASH-WEX pre-treatment inhibited glutamate-induced cell death and was able to revert glutamate-induced changes in HSP70 to a large extent. Furthermore, the analysis on the neuronal plasticity marker NCAM (Neural cell adhesion molecule and its polysialylated form, PSA-NCAM revealed that ASH-WEX has therapeutic potential for prevention of neurodegeneration associated with glutamate-induced excitotoxicty.

Predictive Simulation of Process Windows for Powder Bed Fusion Additive Manufacturing: Influence of the Powder Bulk Density.

Science.gov (United States)

Rausch, Alexander M; Küng, Vera E; Pobel, Christoph; Markl, Matthias; Körner, Carolin

2017-09-22

The resulting properties of parts fabricated by powder bed fusion additive manufacturing processes are determined by their porosity, local composition, and microstructure. The objective of this work is to examine the influence of the stochastic powder bed on the process window for dense parts by means of numerical simulation. The investigations demonstrate the unique capability of simulating macroscopic domains in the range of millimeters with a mesoscopic approach, which resolves the powder bed and the hydrodynamics of the melt pool. A simulated process window reveals the influence of the stochastic powder layer. The numerical results are verified with an experimental process window for selective electron beam-melted Ti-6Al-4V. Furthermore, the influence of the powder bulk density is investigated numerically. The simulations predict an increase in porosity and surface roughness for samples produced with lower powder bulk densities. Due to its higher probability for unfavorable powder arrangements, the process stability is also decreased. This shrinks the actual parameter range in a process window for producing dense parts.

Minimum ignition energy of nano and micro Ti powder in the presence of inert nano TiO₂ powder.

Science.gov (United States)

Chunmiao, Yuan; Amyotte, Paul R; Hossain, Md Nur; Li, Chang

2014-06-15

The inerting effect of nano-sized TiO2 powder on ignition sensitivity of nano and micro Ti powders was investigated with a Mike 3 apparatus. "A little is not good enough" is also suitable for micro Ti powders mixed with nano-sized solid inertants. MIE of the mixtures did not significantly increase until the TiO2 percentage exceeded 50%. Nano-sized TiO2 powders were ineffective as an inertant when mixed with nano Ti powders, especially at higher dust loadings. Even with 90% nano TiO2 powder, mixtures still showed high ignition sensitivity because the statistic energy was as low as 2.1 mJ. Layer fires induced by ignited but unburned metal particles may occur for micro Ti powders mixed with nano TiO2 powders following a low level dust explosion. Such layer fires could lead to a violent dust explosion after a second dispersion. Thus, additional attention is needed to prevent metallic layer fires even where electric spark potential is low. In the case of nano Ti powder, no layer fires were observed because of less flammable material involved in the mixtures investigated, and faster flame propagation in nanoparticle clouds. Copyright © 2014 Elsevier B.V. All rights reserved.

Root rots

Science.gov (United States)

Kathryn Robbins; Philip M. Wargo

1989-01-01

Root rots of central hardwoods are diseases caused by fungi that infect and decay woody roots and sometimes also invade the butt portion of the tree. By killing and decaying roots, root rotting fungi reduce growth, decrease tree vigor, and cause windthrow and death. The most common root diseases of central hardwoods are Armillaria root rot, lnonotus root rot, and...

Ultrasonic wave propagation in powders

Science.gov (United States)

Al-Lashi, R. S.; Povey, M. J. W.; Watson, N. J.

2018-05-01

Powder clumps (cakes) has a significant effect on the flowability and stability of powders. Powder caking is mainly caused by moisture migration due to wetting and environmental (temperature and humidity) changes. The process of moisture migration caking involves creating liquid bridges between the particles during condensation which subsequently harden to form solid bridges. Therefore, an effective and reliable technique is required to quantitatively and non-invasively monitor caking kinetics and effective stiffness. This paper describes two ultrasonic instruments (ultrasonic velocity pulse and airborne ultrasound systems) that have been used to monitor the caking phenomenon. Also, it discusses the relationship between the ultrasonic velocity and attenuation measurements and tracking caking kinetics and the effective stiffness of powders.

A novel root analogue dental implant using CT scan and CAD/CAM: selective laser melting technology.

Science.gov (United States)

Figliuzzi, M; Mangano, F; Mangano, C

2012-07-01

Direct laser metal forming (DLMF) is a new technique which allows solids with complex geometry to be produced by annealing metal powder microparticles in a focused laser beam, according to a computer-generated three-dimensional (3D) model. For dental implants, the fabrication process involves the laser-induced fusion of titanium microparticles, in order to build, layer by layer, the desired object. Modern computed tomography (CT) acquisition and 3D image conversion, combined with the DLMF process, allows the fabrication of custom-made, root-analogue implants (RAI), perfect copies of the radicular units that need replacing. This report demonstrates the successful clinical use of a custom-made, root-analogue DLMF implant. CT images of the residual non-restorable root of a right maxillary premolar were acquired and modified with specific software into a 3D model. From this model, a custom-made, root-analogue, DLMF implant was fabricated. Immediately after tooth extraction, the root-analogue implant was placed in the extraction socket and restored with a single crown. At the 1-year follow-up examination, the custom-made implant showed almost perfect functional and aesthetic integration. The possibility of fabricating custom-made, root-analogue DLMF implants opens new interesting perspectives for immediate placement of dental implants. Copyright © 2012 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Effect of surface energy on powder compactibility.

Science.gov (United States)

Fichtner, Frauke; Mahlin, Denny; Welch, Ken; Gaisford, Simon; Alderborn, Göran

2008-12-01

The influence of surface energy on the compactibility of lactose particles has been investigated. Three powders were prepared by spray drying lactose solutions without or with low proportions of the surfactant polysorbate 80. Various powder and tablet characterisation procedures were applied. The surface energy of the powders was characterized by Inverse Gas Chromatography and the compressibility of the powders was described by the relationship between tablet porosity and compression pressure. The compactibility of the powders was analyzed by studying the evolution of tablet tensile strength with increasing compaction pressure and porosity. All powders were amorphous and similar in particle size, shape, and surface area. The compressibility of the powders and the microstructure of the formed tablets were equal. However, the compactibility and dispersive surface energy was dependent of the composition of the powders. The decrease in tablet strength correlated to the decrease in powder surface energy at constant tablet porosities. This supports the idea that tablet strength is controlled by formation of intermolecular forces over the areas of contact between the particles and that the strength of these bonding forces is controlled by surface energy which, in turn, can be altered by the presence of surfactants.

Safety consideration when handling metal powders

CSIR Research Space (South Africa)

Benson, JM

2012-03-01

Full Text Available to some form of irritation or allergic reaction (e.g. dermatitis). In the case of nano-powders, the particles can penetrate the skin and become absorbed into cells in various parts of the body, including the brain � Eye contact, resulting in a... powders, and thus data is often limited to various ailments that have been reported for people working with that particular powder (amongs other things). There are three ways that powders can interact with the body: � Skin contact, which may lead...

Effect of surface coating with magnesium stearate via mechanical dry powder coating approach on the aerosol performance of micronized drug powders from dry powder inhalers.

Science.gov (United States)

Zhou, Qi Tony; Qu, Li; Gengenbach, Thomas; Larson, Ian; Stewart, Peter J; Morton, David A V

2013-03-01

The objective of this study was to investigate the effect of particle surface coating with magnesium stearate on the aerosolization of dry powder inhaler formulations. Micronized salbutamol sulphate as a model drug was dry coated with magnesium stearate using a mechanofusion technique. The coating quality was characterized by X-ray photoelectron spectroscopy. Powder bulk and flow properties were assessed by bulk densities and shear cell measurements. The aerosol performance was studied by laser diffraction and supported by a twin-stage impinger. High degrees of coating coverage were achieved after mechanofusion, as measured by X-ray photoelectron spectroscopy. Concomitant significant increases occurred in powder bulk densities and in aerosol performance after coating. The apparent optimum performance corresponded with using 2% w/w magnesium stearate. In contrast, traditional blending resulted in no significant changes in either bulk or aerosolization behaviour compared to the untreated sample. It is believed that conventional low-shear blending provides insufficient energy levels to expose host micronized particle surfaces from agglomerates and to distribute guest coating material effectively for coating. A simple ultra-high-shear mechanical dry powder coating step was shown as highly effective in producing ultra-thin coatings on micronized powders and to substantially improve the powder aerosolization efficiency.

Baking Powder Wars

OpenAIRE

Civitello, Linda

2017-01-01

How did a mid-nineteenth century American invention, baking powder, replace yeast as a leavening agent and create a culinary revolution as profound as the use of yeast thousands of years ago?The approach was two-pronged and gendered: business archives, U.S. government records and lawsuits revealed how baking powder was created, marketed, and regulated. Women’s diaries and cookbooks—personal, corporate, community, ethnic—from the eighteenth century to internet blogs showed the use women made o...

PRODUCTION OF POROUS POWDER MATERIALS OF SPHERICAL POWDERS OF CORROSION-RESISTANT STEEL

Directory of Open Access Journals (Sweden)

V. N. Kovalevskij

2012-01-01

Full Text Available Production of porous powder materials from spherical powders of corrosion-resistant steel 12Х18н10Т with formation at low pressures 120–140 mpa in the mold with the subsequent activated sintering became possible due to increase of duration of process of spattering and formation of condensate particles (Si–C or (Mo–Si on surface.

Comparison of blueberry powder produced via foam-mat freeze-drying versus spray-drying: evaluation of foam and powder properties.

Science.gov (United States)

Darniadi, Sandi; Ho, Peter; Murray, Brent S

2018-03-01

Blueberry juice powder was developed via foam-mat freeze-drying (FMFD) and spray-drying (SD) via addition of maltodextrin (MD) and whey protein isolate (WPI) at weight ratios of MD/WPI = 0.4 to 3.2 (with a fixed solids content of 5 wt% for FMFD and 10 wt% for SD). Feed rates of 180 and 360 mL h -1 were tested in SD. The objective was to evaluate the effect of the drying methods and carrier agents on the physical properties of the corresponding blueberry powders and reconstituted products. Ratios of MD/WPI = 0.4, 1.0 and 1.6 produced highly stable foams most suitable for FMFD. FMFD gave high yields and low bulk density powders with flake-like particles of large size that were also dark purple with high red values. SD gave low powder recoveries. The powders had higher bulk density and faster rehydration times, consisting of smooth, spherical and smaller particles than in FMFD powders. The SD powders were bright purple but less red than FMFD powders. Solubility was greater than 95% for both FMFD and SD powders. The FMFD method is a feasible method of producing blueberry juice powder and gives products retaining more characteristics of the original juice than SD. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

[Advances in studies on bear bile powder].

Science.gov (United States)

Zhou, Chao-fan; Gao, Guo-jian; Liu, Ying

2015-04-01

In this paper, a detailed analysis was made on relevant literatures about bear bile powder in terms of chemical component, pharmacological effect and clinical efficacy, indicating bear bile powder's significant pharmacological effects and clinical application in treating various diseases. Due to the complex composition, bear bile powder is relatively toxic. Therefore, efforts shall be made to study bear bile powder's pharmacological effects, clinical application, chemical composition and toxic side-effects, with the aim to provide a scientific basis for widespread reasonable clinical application of bear bile powder.

21 CFR 73.2645 - Aluminum powder.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Aluminum powder. 73.2645 Section 73.2645 Food and... ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2645 Aluminum powder. (a) Identity and specifications. The color additive aluminum powder shall conform in identity and specifications to the requirements of...

CLAY SOIL STABILISATION USING POWDERED GLASS

Directory of Open Access Journals (Sweden)

J. OLUFOWOBI

2014-10-01

Full Text Available This paper assesses the stabilizing effect of powdered glass on clay soil. Broken waste glass was collected and ground into powder form suitable for addition to the clay soil in varying proportions namely 1%, 2%, 5%, 10% and 15% along with 15% cement (base by weight of the soil sample throughout. Consequently, the moisture content, specific gravity, particle size distribution and Atterberg limits tests were carried out to classify the soil using the ASSHTO classification system. Based on the results, the soil sample obtained corresponded to Group A-6 soils identified as ‘fair to poor’ soil type in terms of use as drainage and subgrade material. This justified stabilisation of the soil. Thereafter, compaction, California bearing ratio (CBR and direct shear tests were carried out on the soil with and without the addition of the powdered glass. The results showed improvement in the maximum dry density values on addition of the powdered glass and with corresponding gradual increase up to 5% glass powder content after which it started to decrease at 10% and 15% powdered glass content. The highest CBR values of 14.90% and 112.91% were obtained at 5% glass powder content and 5mm penetration for both the unsoaked and soaked treated samples respectively. The maximum cohesion and angle of internal friction values of 17.0 and 15.0 respectively were obtained at 10% glass powder content.

CVD carbon powders modified by ball milling

Directory of Open Access Journals (Sweden)

Kazmierczak Tomasz

2015-09-01

Full Text Available Carbon powders produced using a plasma assisted chemical vapor deposition (CVD methods are an interesting subject of research. One of the most interesting methods of synthesizing these powders is using radio frequency plasma. This method, originally used in deposition of carbon films containing different sp2/sp3 ratios, also makes possible to produce carbon structures in the form of powder. Results of research related to the mechanical modification of these powders have been presented. The powders were modified using a planetary ball mill with varying parameters, such as milling speed, time, ball/powder mass ratio and additional liquids. Changes in morphology and particle sizes were measured using scanning electron microscopy and dynamic light scattering. Phase composition was analyzed using Raman spectroscopy. The influence of individual parameters on the modification outcome was estimated using statistical method. The research proved that the size of obtained powders is mostly influenced by the milling speed and the amount of balls. Powders tend to form conglomerates sized up to hundreds of micrometers. Additionally, it is possible to obtain nanopowders with the size around 100 nm. Furthermore, application of additional liquid, i.e. water in the process reduces the graphitization of the powder, which takes place during dry milling.

Shock diffraction in alumina powder

International Nuclear Information System (INIS)

Venz, G.; Killen, P.D.; Page, N.W.

1996-01-01

In order to produce complex shaped components by dynamic compaction of ceramic powders detailed knowledge of their response under shock loading conditions is required. This work attempts to provide data on release effects and shock attenuation in 1 μm and 5 μm α-alumina powders which were compacted to between 85 % and 95 % of the solid phase density by the impact of high velocity steel projectiles. As in previous work, the powder was loaded into large cylindrical dies with horizontal marker layers of a contrasting coloured powder to provide a record of powder displacement in the recovered specimens. After recovery and infiltration with a thermosetting resin the specimens were sectioned and polished to reveal the structure formed by the passage of the projectile and shock wave. Results indicate that the shock pressures generated were of the order of 0.5 to 1.4 GPa and higher, with shock velocities and sound speeds in the ranges 650 to 800 m/s and 350 to 400 m/s respectively

In Silico Analysis of Microarray-Based Gene Expression Profiles Predicts Tumor Cell Response to Withanolides

Directory of Open Access Journals (Sweden)

Thomas Efferth

2012-05-01

Full Text Available Withania somnifera (L. Dunal (Indian ginseng, winter cherry, Solanaceae is widely used in traditional medicine. Roots are either chewed or used to prepare beverages (aqueous decocts. The major secondary metabolites of Withania somnifera are the withanolides, which are C-28-steroidal lactone triterpenoids. Withania somnifera extracts exert chemopreventive and anticancer activities in vitro and in vivo. The aims of the present in silico study were, firstly, to investigate whether tumor cells develop cross-resistance between standard anticancer drugs and withanolides and, secondly, to elucidate the molecular determinants of sensitivity and resistance of tumor cells towards withanolides. Using IC50 concentrations of eight different withanolides (withaferin A, withaferin A diacetate, 3-azerininylwithaferin A, withafastuosin D diacetate, 4-B-hydroxy-withanolide E, isowithanololide E, withafastuosin E, and withaperuvin and 19 established anticancer drugs, we analyzed the cross-resistance profile of 60 tumor cell lines. The cell lines revealed cross-resistance between the eight withanolides. Consistent cross-resistance between withanolides and nitrosoureas (carmustin, lomustin, and semimustin was also observed. Then, we performed transcriptomic microarray-based COMPARE and hierarchical cluster analyses of mRNA expression to identify mRNA expression profiles predicting sensitivity or resistance towards withanolides. Genes from diverse functional groups were significantly associated with response of tumor cells to withaferin A diacetate, e.g. genes functioning in DNA damage and repair, stress response, cell growth regulation, extracellular matrix components, cell adhesion and cell migration, constituents of the ribosome, cytoskeletal organization and regulation, signal transduction, transcription factors, and others.

21 CFR 73.1645 - Aluminum powder.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Aluminum powder. 73.1645 Section 73.1645 Food and... ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1645 Aluminum powder. (a) Identity. (1) The color additive aluminum powder shall be composed of finely divided particles of aluminum prepared from virgin aluminum. It...

21 CFR 73.2647 - Copper powder.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Copper powder. 73.2647 Section 73.2647 Food and... ADDITIVES EXEMPT FROM CERTIFICATION Cosmetics § 73.2647 Copper powder. (a) Identity and specifications. The color additive copper powder shall conform in identity and specifications to the requirements of § 73...

Root growth, secondary root formation and root gravitropism in carotenoid-deficient seedlings of Zea mays L

Science.gov (United States)

Ng, Y. K.; Moore, R.

1985-01-01

The effect of ABA on root growth, secondary-root formation and root gravitropism in seedlings of Zea mays was investigated by using Fluridone-treated seedlings and a viviparous mutant, both of which lack carotenoids and ABA. Primary roots of seedlings grown in the presence of Fluridone grew significantly slower than those of control (i.e. untreated) roots. Elongation of Fluridone-treated roots was inhibited significantly by the exogenous application of 1 mM ABA. Exogenous application of 1 micromole and 1 nmole ABA had either no effect or only a slight stimulatory effect on root elongation, depending on the method of application. The absence of ABA in Fluridone-treated plants was not an important factor in secondary-root formation in seedlings less than 9-10 d old. However, ABA may suppress secondary-root formation in older seedlings, since 11-d-old control seedlings had significantly fewer secondary roots than Fluridone-treated seedlings. Roots of Fluridone-treated and control seedlings were graviresponsive. Similar data were obtained for vp-9 mutants of Z. mays, which are phenotypically identical to Fluridone-treated seedlings. These results indicate that ABA is necessary for neither secondary-root formation nor for positive gravitropism by primary roots.

Effect of additives on the orientation of magnetic Sr-ferrite powders in powder injection molded compacts

Energy Technology Data Exchange (ETDEWEB)

Cho, T.S. [Sangju National Unviersity, Sangju (Korea); Jeung, W.Y. [Korea Institute of Science and Technology, Seoul (Korea)

2001-03-01

The effect of additives on the orientation of magnetic Sr-ferrite powders has been studied during powder injection molding under applied magnetic field for fabricating multi=pole anisotropic sintered Sr-ferrite magnets. The orientation of the Sr-ferrite powders depends sensitively on the fluidity of powder-binder mixture, related to the binder additives and the injection molding temperature, and the magnetic field intensity. The orientation of Sr-ferrite powders is good for the compacts with stearic acid added in the binder system of paraffin wax/ carnauba wax/HDPE, but it is poor of the compacts with silane coupling agent added. The orientation of sr-ferrites higher than 80% is achieved at the following useful conditions; apparent viscosity lower than 2500 poise in 1000 sec {sup -1} shear rate and applied magnetic field higher than 4 kOe. (author). 15 refs., 1 tab., 6 figs.

Hydrothermal treatment of coprecipitated YSZ powders

International Nuclear Information System (INIS)

Arakaki, Alexander Rodrigo; Yoshito, Walter Kenji; Ussui, Valter; Lazar, Dolores Ribeiro Ricci

2009-01-01

Zirconia stabilized with 8.5 mol% yttria (YSZ) were synthesized by coprecipitation and resulting gels were hydrothermally treated at 200°C and 220 PSI for 4, 8 and 16 hours. Products were oven dried at 70°C for 24 hours, uniaxially pressed as pellets and sintered at 1500 °C for 1 hour. Powders were characterized for surface area with N 2 gas adsorption, X-ray diffraction, laser diffraction granulometric analysis and scanning and transmission electronic microscopy. Density of ceramics was measured by an immersion method based on the Archimedes principle. Results showed that powders dried at 70°C are amorphous and after treatment has tetragonal/cubic symmetry. Surface area of powders presented a significant reduction after hydrothermal treatment. Ceramics prepared from hydrothermally treated powders have higher green density but sintered pellets are less dense when compared to that made with powders calcined at 800°C for 1 hour due to the agglomerate state of powders. Solvothermal treatment is a promising procedure to enhance density. (author)

Changes in Metabolically Active Bacterial Community during Rumen Development, and Their Alteration by Rhubarb Root Powder Revealed by 16S rRNA Amplicon Sequencing.

Science.gov (United States)

Wang, Zuo; Elekwachi, Chijioke; Jiao, Jinzhen; Wang, Min; Tang, Shaoxun; Zhou, Chuanshe; Tan, Zhiliang; Forster, Robert J

2017-01-01

The objective of this present study was to explore the initial establishment of metabolically active bacteria and subsequent evolution in four fractions: rumen solid-phase (RS), liquid-phase (RL), protozoa-associated (RP), and epithelium-associated (RE) through early weaning and supplementing rhubarb root powder in 7 different age groups (1, 10, 20, 38, 41, 50, and 60 d) during rumen development. Results of the 16S rRNA sequencing based on RNA isolated from the four fractions revealed that the potentially active bacterial microbiota in four fractions were dominated by the phyla Proteobacteria, Firmicutes , and Bacteroidetes regardless of different ages. An age-dependent increment of Chao 1 richness was observed in the fractions of RL and RE. The principal coordinate analysis (PCoA) indicated that samples in four fractions all clustered based on different age groups, and the structure of the bacterial community in RE was distinct from those in other three fractions. The abundances of Proteobacteria decreased significantly ( P < 0.05) with age, while increases in the abundances of Firmicutes and Bacteroidetes were noted. At the genus level, the abundance of the predominant genus Mannheimia in the Proteobacteria phylum decreased significantly ( P < 0.05) after 1 d, while the genera Quinella, Prevotella, Fretibacterium, Ruminococcus, Lachnospiraceae NK3A20 group , and Atopobium underwent different manners of increases and dominated the bacterial microbiota across four fractions. Variations of the distributions of some specific bacterial genera across fractions were observed, and supplementation of rhubarb affected the relative abundance of various genera of bacteria.

Cheese powder as an ingredient in emulsion sausages

DEFF Research Database (Denmark)

Chen, Xiang; Ruiz Carrascal, Jorge; Petersen, Mikael Agerlin

2017-01-01

Different types of cheese powder were added to meat emulsion sausages in order to address its influence on chemical composition, volatile compounds profile and sensory properties, and its potential to reduce salt content through boosting saltiness. Addition of cheese powder to emulsion sausages...... modified their profile of volatile compounds. Blue cheese increased some ketones, alcohols, and esters, while brown cheese brought typical Maillard reaction compounds. Overall, addition of cheese powders to sausages enhanced the intensity of flavour traits. A mixture of hard and blue cheese powder showed...... the highest effect on boosting saltiness, while brown cheese powder showed the strongest umami and meat flavour boosting effect, and sausages with added blue cheese powder showed a more intense aftertaste. Hardness significantly increased due to the addition of blue cheese powder. Addition of cheese powder...

Spheroidization of glass powders for glass ionomer cements.

Science.gov (United States)

Gu, Y W; Yap, A U J; Cheang, P; Kumar, R

2004-08-01

Commercial angular glass powders were spheroidized using both the flame spraying and inductively coupled radio frequency plasma spraying techniques. Spherical powders with different particle size distributions were obtained after spheroidization. The effects of spherical glass powders on the mechanical properties of glass ionomer cements (GICs) were investigated. Results showed that the particle size distribution of the glass powders had a significant influence on the mechanical properties of GICs. Powders with a bimodal particle size distribution ensured a high packing density of glass ionomer cements, giving relatively high mechanical properties of GICs. GICs prepared by flame-spheroidized powders showed low strength values due to the loss of fine particles during flame spraying, leading to a low packing density and few metal ions reacting with polyacrylic acid to form cross-linking. GICs prepared by the nano-sized powders showed low strength because of the low bulk density of the nano-sized powders and hence low powder/liquid ratio of GICs.

Effect of powder geometry on densification

International Nuclear Information System (INIS)

Spasskij, M.R.; Spasskaya, I.A.; Shatalova, I.G.; Shchukin, E.D.

1979-01-01

The effect of particle shape and size composition on the processes of powder vibratory compacting is considered. Using microstress measurements in compacted structures of conglomerated and disintegrated tungsten powders as well as powder strength testing the existence of a zone of transition from a structural deformation to a plastic one has been shown. The formation of phase interparticle contacts of practically stable strength (approximately 5-6 dyn) is a characteristic feature of the zone. The width of the transition zone greatly depends upon geometrical powder properties; 55-65 % for conglomerated tungsten, 63-66 % for integrated tungsten

Research on Durability of Recycled Ceramic Powder Concrete

Science.gov (United States)

Chen, M. C.; Fang, W.; Xu, K. C.; Xie, L.

2017-06-01

Ceramic was ground into powder with 325 mesh and used to prepare for concrete. Basic mechanical properties, carbonation and chloride ion penetration of the concrete tests were conducted. In addition, 6-hour electric fluxes of recycled ceramic powder concrete were measured under loading. The results showed that the age strength of ceramics powder concrete is higher than that of the ordinary concrete and the fly ash concrete. The ceramic powder used as admixture would reduce the strength of concrete under no consideration of its impact factor; under consideration of the impact factor for ceramic powder as admixture, the carbonation resistance of ceramic powder concrete was significantly improved, and the 28 day carbonation depth of the ceramic powder concrete was only 31.5% of ordinary concrete. The anti-chloride-permeability of recycled ceramic powder concrete was excellent.

Simple process to fabricate nitride alloy powders

International Nuclear Information System (INIS)

Yang, Jae Ho; Kim, Dong-Joo; Kim, Keon Sik; Rhee, Young Woo; Oh, Jang-Soo; Kim, Jong Hun; Koo, Yang Hyun

2013-01-01

Uranium mono-nitride (UN) is considered as a fuel material [1] for accident-tolerant fuel to compensate for the loss of fissile fuel material caused by adopting a thickened cladding such as SiC composites. Uranium nitride powders can be fabricated by a carbothermic reduction of the oxide powders, or the nitriding of metal uranium. Among them, a direct nitriding process of metal is more attractive because it has advantages in the mass production of high-purity powders and the reusing of expensive 15 N 2 gas. However, since metal uranium is usually fabricated in the form of bulk ingots, it has a drawback in the fabrication of fine powders. The Korea Atomic Energy Research Institute (KAERI) has a centrifugal atomisation technique to fabricate uranium and uranium alloy powders. In this study, a simple reaction method was tested to fabricate nitride fuel powders directly from uranium metal alloy powders. Spherical powder and flake of uranium metal alloys were fabricated using a centrifugal atomisation method. The nitride powders were obtained by thermal treating the metal particles under nitrogen containing gas. The phase and morphology evolutions of powders were investigated during the nitriding process. A phase analysis of nitride powders was also part of the present work. KAERI has developed the centrifugal rotating disk atomisation process to fabricate spherical uranium metal alloy powders which are used as advanced fuel materials for research reactors. The rotating disk atomisation system involves the tasks of melting, atomising, and collecting. A nozzle in the bottom of melting crucible introduces melt at the center of a spinning disk. The centrifugal force carries the melt to the edge of the disk and throws the melt off the edge. Size and shape of droplets can be controlled by changing the nozzle size, the disk diameter and disk speed independently or simultaneously. By adjusting the processing parameters of the centrifugal atomiser, a spherical and flake shape

MECHANICS OF DYNAMIC POWDER COMPACTION PROCESS

OpenAIRE

Nurettin YAVUZ

1996-01-01

In recent years, interest in dynamic compaction methods of metal powders has increased due to the need to improve compaction properties and to increase production rates of compacts. In this paper, review of dynamic and explosive compaction of metal powders are given. An attempt is made to get a better understanding of the compaction process with the mechanicis of powder compaction.

Efficacy of wild plant in combination with microbial antagonists for the control of root rot fungi on mungbean and cowpea

International Nuclear Information System (INIS)

Ikram, N.; Dawar, S.

2015-01-01

Present work was carried out to investigate the efficacy of Aerva javanica in combination with different microbial antagonists namely Rhizobium meliloti, Pseudomonas aeruginosa, Trichoderma harzianum and Aspergillus niger. Soil amended with A. javanica stem, leaves, flower powder at the rate1% w/w and seeds of cowpea (Vigna unguiculata L.) and mungbean (Vigna radiata L.) were coated with microbial antagonists for the control of root infecting fungi like Macrophomina phaseolina (Tassi) Goid, Fusarium spp. and Rhizoctonia solani Kiihn. Infection of M. phaseolina and R. solani were completely suppressed when seeds were coated with P. aeruginosa, T. harzianum, A. niger, R. meliloti and A. javanica leaves powder mixed in soil at the rate 1% w/w. All antagonists showed reduction in combination with A. javanica leaves powder at the rate1% but T. harzianum and P. aeruginosa in combination with A. javanica leaves showed promising results in complete reduction of R. solani and M. phaseolina on both crops. All growth parameters were maximum when soil was amended with A. javanica leaves powder at the rate 1% w/w and seeds were coated with T. harzianum and P. aeruginosa. (author)

Tantalum powder consolidation, modeling and properties

International Nuclear Information System (INIS)

Bingert, S.R.; Vargas, V.D.; Sheinberg, H.C.

1996-01-01

A systematic approach was taken to investigate the consolidation of tantalum powders. The effects of sinter time, temperature and ramp rate; hot isostatic pressing (HIP) temperature and time; and powder oxygen content on consolidation density, kinetics, microstructure, crystallographic texture, and mechanical properties have been evaluated. In general, higher temperatures and longer hold times resulted in higher density compacts with larger grain sizes for both sintering and HIP'ing. HIP'ed compacts were consistently higher in density than sintered products. The higher oxygen content powders resulted in finer grained, higher density HIP'ed products than the low oxygen powders. Texture analysis showed that the isostatically processed powder products demonstrated a near random texture. This resulted in isotropic properties in the final product. Mechanical testing results showed that the HIP'ed powder products had consistently higher flow stresses than conventionally produced plates, and the sintered compacts were comparable to the plate material. A micromechanics model (Ashby HIP model) has been employed to predict the mechanisms active in the consolidation processes of cold isostatic pressing (CIP), HIP and sintering. This model also predicts the density of the end product and whether grain growth should be expected under the applied processing conditions

Vacuum hot pressing of titanium-alloy powders

International Nuclear Information System (INIS)

Malik, R.K.

1975-01-01

Full or nearly full dense products of wrought-metal properties have been obtained by vacuum hot pressing (VHP) of several prealloyed Ti--6Al--4V powders including hydride, hydride/dehydride, and rotating electrode process (REP) spherical powder. The properties of billets VHP from Ti--6Al--4V hydride powder and from hydride/dehydride powders have been shown to be equivalent. The REP spherical powder billets processed by VHP or by hot isostatic pressing (HIP) resulted in equivalent tensile properties. The potential of VHP for fabrication of near net aircraft parts such as complex fittings and engine disks offers considerable cost savings due to reduced material and machining requirements

Superconductors by powder metallurgy techniques

International Nuclear Information System (INIS)

Pickus, M.R.; Wang, J.L.F.

1976-05-01

Fabrication methods for Nb 3 Sn type compounds are described. Information is included on the Bell Telephone process, the General Electric tape process, superconductor stability, the bronze process, powder metallurgy multifilamentary tapes and wires, and current assessment of powder metallurgy superconducting wire

Root development during soil genesis: effects of root-root interactions, mycorrhizae, and substrate

Science.gov (United States)

Salinas, A.; Zaharescu, D. G.

2015-12-01

A major driver of soil formation is the colonization and transformation of rock by plants and associated microbiota. In turn, substrate chemical composition can also influence the capacity for plant colonization and development. In order to better define these relationships, a mesocosm study was set up to analyze the effect mycorrhizal fungi, plant density and rock have on root development, and to determine the effect of root morphology on weathering and soil formation. We hypothesized that plant-plant and plant-fungi interactions have a stronger influence on root architecture and rock weathering than the substrate composition alone. Buffalo grass (Bouteloua dactyloides) was grown in a controlled environment in columns filled with either granular granite, schist, rhyolite or basalt. Each substrate was given two different treatments, including grass-microbes and grass-microbes-mycorrhizae and incubated for 120, 240, and 480 days. Columns were then extracted and analyzed for root morphology, fine fraction, and pore water major element content. Preliminary results showed that plants produced more biomass in rhyolite, followed by schist, basalt, and granite, indicating that substrate composition is an important driver of root development. In support of our hypothesis, mycorrhizae was a strong driver of root development by stimulating length growth, biomass production, and branching. However, average root length and branching also appeared to decrease in response to high plant density, though this trend was only present among roots with mycorrhizal fungi. Interestingly, fine fraction production was negatively correlated with average root thickness and volume. There is also slight evidence indicating that fine fraction production is more related to substrate composition than root morphology, though this data needs to be further analyzed. Our hope is that the results of this study can one day be applied to agricultural research in order to promote the production of crops

Impact strength of sintered astaloy CrM powders

International Nuclear Information System (INIS)

Kazior, J.; Ploszczak, J.; Nykiel, M.; Pieczonka, T.

2003-01-01

In this paper results of a series of impact tests on sintered Astaloy CrM powders alloys modified by boron are presented and discussed. Boron in different forms, i.e. as elemental boron powder, boron carbide B 4 C powder or mixture of boron and carbon elemental powders, was used in different weight percentage to activate sintering of Astaloy CrM powder and to increase hardenability, with aim of increasing impact strength in view of structural applications. (author)

Dwell Notch Low Cycle Fatigue Behavior of a Powder Metallurgy Nickel Disk Alloy

Science.gov (United States)

Telesman, J.; Gabb, T. P.; Yamada, Y.; Ghosn, L. J.; Jayaraman, N.

2012-01-01

A study was conducted to determine the processes which govern dwell notch low cycle fatigue (NLCF) behavior of a powder metallurgy (P/M) ME3 disk superalloy. The emphasis was placed on the environmentally driven mechanisms which may embrittle the highly stressed notch surface regions and reduce NLCF life. In conjunction with the environmentally driven notch surface degradation processes, the visco-plastic driven mechanisms which can significantly change the notch root stresses were also considered. Dwell notch low cycle fatigue testing was performed in air and vacuum on a ME3 P/M disk alloy specimens heat treated using either a fast or a slow cooling rate from the solutioning treatment. It was shown that dwells at the minimum stress typically produced a greater life debit than the dwells applied at the maximum stress, especially for the slow cooled heat treatment. Two different environmentally driven failure mechanisms were identified as the root cause of early crack initiation in the min dwell tests. Both of these failure mechanisms produced mostly a transgranular crack initiation failure mode and yet still resulted in low NLCF fatigue lives. The lack of stress relaxation during the min dwell tests produced higher notch root stresses which caused early crack initiation and premature failure when combined with the environmentally driven surface degradation mechanisms. The importance of environmental degradation mechanisms was further highlighted by vacuum dwell NLCF tests which resulted in considerably longer NLCF lives, especially for the min dwell tests.

Shock compaction of molybdenum powder

Science.gov (United States)

Ahrens, T. J.; Kostka, D.; Vreeland, T., Jr.; Schwarz, R. B.; Kasiraj, P.

1983-01-01

Shock recovery experiments which were carried out in the 9 to 12 GPa range on 1.4 distension Mo and appear adequate to compact to full density ( 45 (SIGMA)m) powders were examined. The stress levels, however, are below those calculated to be from 100 to approx. 22 GPa which a frictional heating model predicts are required to consolidate approx. 10 to 50 (SIGMA)m particles. The model predicts that powders that have a distension of m=1.6 shock pressures of 14 to 72 GPa are required to consolidate Mo powders in the 50 to 10 (SIGMA)m range.

Rooting gene trees without outgroups: EP rooting.

Science.gov (United States)

Sinsheimer, Janet S; Little, Roderick J A; Lake, James A

2012-01-01

Gene sequences are routinely used to determine the topologies of unrooted phylogenetic trees, but many of the most important questions in evolution require knowing both the topologies and the roots of trees. However, general algorithms for calculating rooted trees from gene and genomic sequences in the absence of gene paralogs are few. Using the principles of evolutionary parsimony (EP) (Lake JA. 1987a. A rate-independent technique for analysis of nucleic acid sequences: evolutionary parsimony. Mol Biol Evol. 4:167-181) and its extensions (Cavender, J. 1989. Mechanized derivation of linear invariants. Mol Biol Evol. 6:301-316; Nguyen T, Speed TP. 1992. A derivation of all linear invariants for a nonbalanced transversion model. J Mol Evol. 35:60-76), we explicitly enumerate all linear invariants that solely contain rooting information and derive algorithms for rooting gene trees directly from gene and genomic sequences. These new EP linear rooting invariants allow one to determine rooted trees, even in the complete absence of outgroups and gene paralogs. EP rooting invariants are explicitly derived for three taxon trees, and rules for their extension to four or more taxa are provided. The method is demonstrated using 18S ribosomal DNA to illustrate how the new animal phylogeny (Aguinaldo AMA et al. 1997. Evidence for a clade of nematodes, arthropods, and other moulting animals. Nature 387:489-493; Lake JA. 1990. Origin of the metazoa. Proc Natl Acad Sci USA 87:763-766) may be rooted directly from sequences, even when they are short and paralogs are unavailable. These results are consistent with the current root (Philippe H et al. 2011. Acoelomorph flatworms are deuterostomes related to Xenoturbella. Nature 470:255-260).

Metal powder production by gas atomization

Science.gov (United States)

Ting, E. Y.; Grant, N. J.

1986-01-01

The confined liquid, gas-atomization process was investigated. Results from a two-dimensional water model showed the importance of atomization pressure, as well as delivery tube and atomizer design. The atomization process at the tip of the delivery tube was photographed. Results from the atomization of a modified 7075 aluminum alloy yielded up to 60 wt pct. powders that were finer than 45 microns in diameter. Two different atomizer designs were evaluated. The amount of fine powders produced was correlated to a calculated gas-power term. An optimal gas-power value existed for maximized fine powder production. Atomization at gas-power greater than or less than this optimal value produced coarser powders.

Hygroscopic behavior of lyophilized acerola pulp powder

Directory of Open Access Journals (Sweden)

Luciana C. Ribeiro

2016-03-01

Full Text Available ABSTRACT Powder products are characterized by their practicality and long life. However, fruit powders have high hygroscopicity and tend to agglomerate due to its hydrophilic nature. The isotherms of equilibrium moisture content apply to the study of dehydrated food preservation potential. Acerola is a nutritionally rich fruit, with great economic and industrial potential. The objective of this study was to analyse acerola powder adsorption isotherms obtained by lyophilization and characterize the powder obtained from lyophilized acerola pulp. Analysis of hygroscopicity, solubility and degree of caking were performed. Isotherms were represented by the mathematical models of GAB, BET, Henderson and Oswin, at temperatures of 25, 35 and 45 °C. According to the results, the obtained powder showed hygroscopicity of 5.96 g of absorbed water 100g-1 of solids, solubility of 95.08% and caking of 14.12%. The BET model showed the best fit to the adsorption isotherms of the acerola pulp powder obtained by lyophilization. The obtained isotherm was of type III, with a "J" shape. There was an inversion of the effect of temperature on the isotherms of acerola powders.

RootJS: Node.js Bindings for ROOT 6

Science.gov (United States)

Beffart, Theo; Früh, Maximilian; Haas, Christoph; Rajgopal, Sachin; Schwabe, Jonas; Wolff, Christoph; Szuba, Marek

2017-10-01

We present rootJS, an interface making it possible to seamlessly integrate ROOT 6 into applications written for Node.js, the JavaScript runtime platform increasingly commonly used to create high-performance Web applications. ROOT features can be called both directly from Node.js code and by JIT-compiling C++ macros. All rootJS methods are invoked asynchronously and support callback functions, allowing non-blocking operation of Node.js applications using them. Last but not least, our bindings have been designed to platform-independent and should therefore work on all systems supporting both ROOT 6 and Node.js. Thanks to rootJS it is now possible to create ROOT-aware Web applications taking full advantage of the high performance and extensive capabilities of Node.js. Examples include platforms for the quality assurance of acquired, reconstructed or simulated data, book-keeping and e-log systems, and even Web browser-based data visualisation and analysis.

Evaluation of bacterial leakage of four root- end filling materials: Gray Pro Root MTA, White Pro Root MTA, Root MTA and Portland Cement (type I

Directory of Open Access Journals (Sweden)

Zarabian M.

2005-07-01

Full Text Available Background and Aim: Today several materials have been used for root- end filling in endodontic surgery. Optimal properties of Pro Root MTA in in-vitro and in-vivo studies has been proven. On the other hand, based on some studies, Root MTA (Iranian Pro Root MTA and Portland cement are similar to Pro Root MTA in physical and biologic properties. The aim of this study was to evaluate bacterial leakage (amount and mean leakage time of four root- end filling materials. Materials and Methods: In this experimental in-vitro study, seventy six extracted single- rooted human teeth were randomly divided into six groups for root-end filling with gray Pro Root MTA, white Pro Root MTA, Root MTA (Iranian Pro Root MTA, Portland Cement (type I and positive and negative control groups. Root canals were instrumented using the step- back technique. Root- end filling materials were placed in 3mm ultra sonic retro preparations. Samples and microleakage model system were sterilized in autoclave. The apical 3-4 mm of the roots were immersed in phenol red with 3% lactose broth culture medium. The coronal access of each specimen was inoculated every 24h with a suspension of Streptococcus sanguis (ATCC 10556. Culture media were observed every 24h for colour change indicating bacterial contamination for 60 days. Statistical analysis was performed using log- rank test with P<0.05 as the limit of significance. Results: At the end of study 50%, 56.25%, 56.25% and 50% of specimens filled with Gray Pro Root MTA, White Pro Root MTA. Root MTA and Portland Cement (type I had evidence of leakage respectively. The mean leakage time was 37.19±6.29, 36.44±5.81, 37.69±5.97 and 34.81±6.67 days respectively. Statistical analysis of data showed no significant difference among the leakage (amount and mean leakage time of the four tested root- end filling materials (P=0.9958. Conclusion: Based on the results of this study, there were no significant differences in leakage among the four

Metallography of powder metallurgy materials

International Nuclear Information System (INIS)

Lawley, Alan; Murphy, Thomas F.

2003-01-01

The primary distinction between the microstructure of an ingot metallurgy/wrought material and one fabricated by the powder metallurgy route of pressing followed by sintering is the presence of porosity in the latter. In its various morphologies, porosity affects the mechanical, physical, chemical, electrical and thermal properties of the material. Thus, it is important to be able to characterize quantitatively the microstructure of powder metallurgy parts and components. Metallographic procedures necessary for the reliable characterization of microstructures in powder metallurgy materials are reviewed, with emphasis on the intrinsic challenges presented by the presence of porosity. To illustrate the utility of these techniques, five case studies are presented involving powder metallurgy materials. These case studies demonstrate problem solving via metallography in diverse situations: failure of a tungsten carbide-coated precipitation hardening stainless steel, failure of a steel pump gear, quantification of the degree of sinter (DOS), simulation of performance of a porous filter using automated image analysis, and analysis of failure in a sinter brazed part assembly

Spheroidization of molybdenum powder by radio frequency thermal plasma

Science.gov (United States)

Liu, Xiao-ping; Wang, Kuai-she; Hu, Ping; Chen, Qiang; Volinsky, Alex A.

2015-11-01

To control the morphology and particle size of dense spherical molybdenum powder prepared by radio frequency (RF) plasma from irregular molybdenum powder as a precursor, plasma process parameters were optimized in this paper. The effects of the carrier gas flow rate and molybdenum powder feeding rate on the shape and size of the final products were studied. The molybdenum powder morphology was examined using high-resolution scanning electron microscopy. The powder phases were analyzed by X-ray diffraction. The tap density and apparent density of the molybdenum powder were investigated using a Hall flow meter and a Scott volumeter. The optimal process parameters for the spherical molybdenum powder preparation are 50 g/min powder feeding rate and 0.6 m3/h carrier gas rate. In addition, pure spherical molybdenum powder can be obtained from irregular powder, and the tap density is enhanced after plasma processing. The average size is reduced from 72 to 62 µm, and the tap density is increased from 2.7 to 6.2 g/cm3. Therefore, RF plasma is a promising method for the preparation of high-density and high-purity spherical powders.

In-house characterization of protein powder

DEFF Research Database (Denmark)

Hartmann, Christian Grundahl; Nielsen, Ole Faurskov; Ståhl, Kenny

2010-01-01

X-ray powder diffraction patterns of lysozyme and insulin were recorded on a standard in-house powder diffractometer. The experimental powder diffraction patterns were compared with patterns calculated from Protein Data Bank coordinate data. Good agreement was obtained by including straightforward...... to include calculated H-atom positions did not improve the overall fit and was abandoned. The method devised was shown to be a quick and convenient tool for distinguishing precipitates and polymorphs of proteins....

Powder handling for automated fuel processing

International Nuclear Information System (INIS)

Frederickson, J.R.; Eschenbaum, R.C.; Goldmann, L.H.

1989-01-01

Installation of the Secure Automated Fabrication (SAF) line has been completed. It is located in the Fuel Cycle Plant (FCP) at the Department of Energy's (DOE) Hanford site near Richland, Washington. The SAF line was designed to fabricate advanced reactor fuel pellets and assemble fuel pins by automated, remote operation. This paper describes powder handling equipment and techniques utilized for automated powder processing and powder conditioning systems in this line. 9 figs

Root proliferation in decaying roots and old root channels: A nutrient conservation mechanism in oligotrophic mangrove forests?

Science.gov (United States)

McKee, K.L.

2001-01-01

1. In oligotrophic habitats, proliferation of roots in nutrient-rich microsites may contribute to overall nutrient conservation by plants. Peat-based soils on mangrove islands in Belize are characterized by the presence of decaying roots and numerous old root channels (0.1-3.5 cm diameter) that become filled with living and highly branched roots of Rhizophora mangle and Avicennia germinans. The objectives of this study were to quantify the proliferation of roots in these microsites and to determine what causes this response. 2. Channels formed by the refractory remains of mangrove roots accounted for only 1-2% of total soil volume, but the proportion of roots found within channels varied from 9 to 24% of total live mass. Successive generations of roots growing inside increasingly smaller root channels were also found. 3. When artificial channels constructed of PVC pipe were buried in the peat for 2 years, those filled with nutrient-rich organic matter had six times more roots than empty or sand-filled channels, indicating a response to greater nutrient availability rather than to greater space or less impedance to root growth. 4. Root proliferation inside decaying roots may improve recovery of nutrients released from decomposing tissues before they can be leached or immobilized in this intertidal environment. Greatest root proliferation in channels occurred in interior forest zones characterized by greater soil waterlogging, which suggests that this may be a strategy for nutrient capture that minimizes oxygen losses from the whole root system. 5. Improved efficiency of nutrient acquisition at the individual plant level has implications for nutrient economy at the ecosystem level and may explain, in part, how mangroves persist and grow in nutrient-poor environments.

Development of granular powder manufacturing technology by spray pyrolysis

International Nuclear Information System (INIS)

Katoh, Yoshiyuki; Kawase, Keiichi; Takahashi, Yoshiharu; Todokoro, Akio

1996-01-01

For shortening of mixed-oxide (MOX) fuel manufacturing process and improvement in treatment of MOX-powder, we have been developing the granular powder production technology. Since the granular powders have excellent fluidity owing to the spherical shape, there is the possibility of modifying scattering and adcering of the powder in the process equipment. In this paper, spray pyrolysis process in adopted as the process of manufacturing the granular powders and the basic feasibility study has been carried out. The experimental results show that the manufactured granular powders have excellent fluidity and the diameter of the powders is controllable. Furthermore, high density pellets are formed by sintering the powders. Thus, it is clarified that this process is promising for the actual MOX fuel fabrication. (author)

Vibration-Assisted Handling of Dry Fine Powders

Directory of Open Access Journals (Sweden)

Paul Dunst

2018-04-01

Full Text Available Since fine powders tend strongly to adhesion and agglomeration, their processing with conventional methods is difficult or impossible. Typically, in order to enable the handling of fine powders, chemicals are added to increase the flowability and reduce adhesion. This contribution shows that instead of additives also vibrations can be used to increase the flowability, to reduce adhesion and cohesion, and thus to enable or improve processes such as precision dosing, mixing, and transport of very fine powders. The methods for manipulating powder properties are described in detail and prototypes for experimental studies are presented. It is shown that the handling of fine powders can be improved by using low-frequency, high-frequency or a combination of low- and high-frequency vibration.

Evaluation of ring shear testing as a characterization method for powder flow in small-scale powder processing equipment

DEFF Research Database (Denmark)

Søgaard, Søren Vinter; Pedersen, Troels; Allesø, Morten

2014-01-01

Powder flow in small-scale equipment is challenging to predict. To meet this need, the impact of consolidation during powder flow characterization, the level of consolidation existing during discharge of powders from a tablet press hopper and the uncertainty of shear and wall friction measurements...... normal stress were approximately 200Pa and 114Pa, respectively, in the critical transition from the converging to the lower vertical section of the hopper. The lower limit of consolidation for the shear and wall friction test was approximately 500Pa and 200Pa, respectively. At this consolidation level......, the wall and shear stress resolution influences the precision of the measured powder flow properties. This study highlights the need for an improved experimental setup which would be capable of measuring the flow properties of powders under very small consolidation stresses with a high shear stress...

Fabrication of nuclear fuel by powder injection moulding: Study of the binders systems and the de-binding of feedstock containing actinide powder

International Nuclear Information System (INIS)

Bricout, J.

2012-01-01

Powder Injection Moulding (PIM) is identified as an innovative process for the nuclear fuel fabrication. Technological breakthrough compared to the current process of powder metallurgy, the impact of actinide powder's specificities on the different steps of PIM is performed. Alumina powders simulating actinide powder have been implemented with a reference binders system. Thermal and rheological studies show the injectability and the de-binding of feedstocks with adequate solid loading (≥50 %vol), thanks to the de-agglomeration during the mixing step, which allow to obtain net shape fuel pellet. Specific surface area of powders, acting as a key role in behaviour's feedstocks, has been integrated in analysis models of viscosity prediction according to the shear rate. Also conducted studies on uranium oxide powder show that the selected binders systems, which have a compatible rheological behaviour with PIM process, impact the de-agglomeration of powder and final microstructure of the fuel pellet, consistent with the results obtained on alumina powders. Independent behaviour of binders and uranium oxide powder, showing no adverse chemical reaction against the PIM process, show a residual mass of carbon of about 150 ppm after sintering. Binders system using polystyrene, resistant to radiolysis phenomena and loadable more than 50 %(vol) of actinide powder, shows the promising potential of PIM process for the fuel fabrication. (author) [fr

Spray drying of beryllium oxide powder

International Nuclear Information System (INIS)

Sepulveda, J.L.; Kahler, D.A.

1991-01-01

Forming of beryllia ceramics through dry pressing requires the agglomeration of the powder through spray drying. To produce high quality fired ceramics it is necessary to disperse/grind the primary powder prior to binder addition. Size reduction of the powder is accomplished using an aqueous system in Vibro-Energy mills (VEM) charged with beryllia media to minimize contamination. Two VEM mills of different size were used to characterize the grinding operation. Details of the grinding kinetics are described within the context of the Macroscopic Population Balance Model approach. Spray drying of the ceramic slurry was accomplished with both a centrifugal atomizer and a two fluid nozzle atomizer. Two different spray dryers were used. Important operating parameters affecting the size distribution of the spray dried powder are discussed

Method of producing radioactive carbon powder

International Nuclear Information System (INIS)

Imamura, Y.

1980-01-01

Carbon powder, placed in a hermetically closed apparatus under vacuum together with radium ore, adsorbs radon gas emanating from the radium ore thus producing a radioactive carbonaceous material, the radioactivity of which is due to the presence of adsorbed radon. The radioactive carbon powder thus obtained has excellent therapeutical efficacy and is suitable for a variety of applications because of the mild radioactivity of radon. Radium ore permits substantially limitlessly repeated production of the radioactive carbon powder

Preparation techniques for ceramic waste form powder

International Nuclear Information System (INIS)

Hash, M.C.; Pereira, C.; Lewis, M.A.

1997-01-01

The electrometallurgical treatment of spent nuclear fuels result in a chloride waste salt requiring geologic disposal. Argonne National Laboratory (ANL) is developing ceramic waste forms which can incorporate this waste. Currently, zeolite- or sodalite-glass composites are produced by hot isostatic pressing (HIP) techniques. Powder preparations include dehydration of the raw zeolite powders, hot blending of these zeolite powders and secondary additives. Various approaches are being pursued to achieve adequate mixing, and the resulting powders have been HIPed and characterized for leach resistance, phase equilibria, and physical integrity

Synthesis of a TiBw/Ti6Al4V composite by powder compact extrusion using a blended powder mixture

Energy Technology Data Exchange (ETDEWEB)

Lu, Huiyang, E-mail: hl209@waikato.ac.nz [Waikato Center for Advanced Materials, School of Engineering, University of Waikato, Hamilton (New Zealand); Zhang, Deliang, E-mail: zhangdeliang@sjtu.edu.cn [State Key Laboratory of Metal Matrix Composites, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai (China); Gabbitas, Brian, E-mail: briang@waikato.ac.nz [Waikato Center for Advanced Materials, School of Engineering, University of Waikato, Hamilton (New Zealand); Yang, Fei, E-mail: fyang@waikato.ac.nz [Waikato Center for Advanced Materials, School of Engineering, University of Waikato, Hamilton (New Zealand); Matthews, Steven, E-mail: S.Matthews@massey.ac.nz [School of Engineering and Advanced Technology, Massey University, Auckland (New Zealand)

2014-09-01

Highlights: • TiB/Ti6Al4V composites were prepared from extruded BE powders. • Different starting powders affected the morphologies of TiB whiskers formed in-situ. • A TiB/Ti6Al4V composite with TiB whiskers had good strength and ductility. • The strength and ductility achieved were superior to those obtained by other methods. - Abstract: A Ti–6 wt%Al–4 wt%V alloy (Ti6Al4V) matrix composite, reinforced by in situ synthesized TiB whiskers (TiBw) has been successfully fabricated by powder compact extrusion using a blended powder mixture. The microstructural characterization of the various extruded samples showed that the different starting powders, pre-alloyed powder plus boron powder or titanium plus Al–40V master alloy powder plus boron powder, had a significant effect on the morphology of the in situ synthesized TiB whiskers. It is also evident that the TiB whiskers affect the microstructural evolution of the Ti6Al4V matrix. The tensile test results indicated that the composite with a dispersion of fine TiB whiskers with high aspect ratios exhibited a high ultimate tensile stress (UTS) and yield stress (YS) of 1436 MPa and 1361 MPa, respectively, a reasonably good tensile ductility reflected by an elongation to fracture of 5.6% was also achieved. This is a significant improvement compared with as-extruded monolithic Ti6Al4V alloy produced in this study.

Synthesis of a TiBw/Ti6Al4V composite by powder compact extrusion using a blended powder mixture

International Nuclear Information System (INIS)

Lu, Huiyang; Zhang, Deliang; Gabbitas, Brian; Yang, Fei; Matthews, Steven

2014-01-01

Highlights: • TiB/Ti6Al4V composites were prepared from extruded BE powders. • Different starting powders affected the morphologies of TiB whiskers formed in-situ. • A TiB/Ti6Al4V composite with TiB whiskers had good strength and ductility. • The strength and ductility achieved were superior to those obtained by other methods. - Abstract: A Ti–6 wt%Al–4 wt%V alloy (Ti6Al4V) matrix composite, reinforced by in situ synthesized TiB whiskers (TiBw) has been successfully fabricated by powder compact extrusion using a blended powder mixture. The microstructural characterization of the various extruded samples showed that the different starting powders, pre-alloyed powder plus boron powder or titanium plus Al–40V master alloy powder plus boron powder, had a significant effect on the morphology of the in situ synthesized TiB whiskers. It is also evident that the TiB whiskers affect the microstructural evolution of the Ti6Al4V matrix. The tensile test results indicated that the composite with a dispersion of fine TiB whiskers with high aspect ratios exhibited a high ultimate tensile stress (UTS) and yield stress (YS) of 1436 MPa and 1361 MPa, respectively, a reasonably good tensile ductility reflected by an elongation to fracture of 5.6% was also achieved. This is a significant improvement compared with as-extruded monolithic Ti6Al4V alloy produced in this study

(YSZ) powders

Indian Academy of Sciences (India)

Unknown

109–114. © Indian Academy of Sciences. 109 ... Materials Science Division, Bhabha Atomic Research Centre, Mumbai 400 085, India .... pensions of 900°C calcined YSZ powders. .... The sintered density data of the compacts (sintered at.

Internal Friction Angle of Metal Powders

Directory of Open Access Journals (Sweden)

Jiri Zegzulka

2018-04-01

Full Text Available Metal powders are components with multidisciplinary usage as their application is very broad. Their consistent characterization across all disciplines is important for ensuring repeatable and trouble-free processes. Ten metal powders were tested in the study. In all cases, the particle size distribution and morphology (scanning electron microscope—SEM photos were determined. The aim of this work was to inspect the flow behavior of metal powders through another measured characteristic, namely the angle of internal friction. The measured values of the effective internal friction angle in the range 28.6–32.9°, together with the spherical particle shape and the particle size distribution, revealed the likely dominant mode of the metal particle transfer mechanism for stainless steel 316L, zinc and aluminum powder. This third piston flow mechanism is described and illustrated in detail. The angle of internal friction is mentioned as another suitable parameter for the characterization of metal powders, not only for the relative simplicity of the determination but also for gaining insight into the method of the movement of individual particles during the flow.

Device for preparing combinatorial libraries in powder metallurgy.

Science.gov (United States)

Yang, Shoufeng; Evans, Julian R G

2004-01-01

This paper describes a powder-metering, -mixing, and -dispensing mechanism that can be used as a method for producing large numbers of samples for metallurgical evaluation or electrical or mechanical testing from multicomponent metal and cermet powder systems. It is designed to make use of the same commercial powders that are used in powder metallurgy and, therefore, to produce samples that are faithful to the microstructure of finished products. The particle assemblies produced by the device could be consolidated by die pressing, isostatic pressing, laser sintering, or direct melting. The powder metering valve provides both on/off and flow rate control of dry powders in open capillaries using acoustic vibration. The valve is simple and involves no relative movement, avoiding seizure with fine powders. An orchestra of such valves can be arranged on a building platform to prepare multicomponent combinatorial libraries. As with many combinatorial devices, identification and evaluation of sources of mixing error as a function of sample size is mandatory. Such an analysis is presented.

Preparation procedure for spherical titanium powders by RF induction plasma

International Nuclear Information System (INIS)

Gu Zhongtao; Jin Yuping; Ye Gaoying

2011-01-01

The paper uses the single-factor method for the study of spherical titanium powder preparation process. Titanium powders with excellent sphericity can be prepared through controlling and regulating the radio frequency plasma anode working current and voltage, central gas flow rate, sheath gas flow rate, powder-carrying gas flow rate, negative ventilation pressure and powder feed rate, etc. Spheroidization of titanium powders with a size of (17.0±2.0) μm is performed by radio frequency plasma technology. With the increase of negative ventilation pressure, the spheroidization rate of titanium powders increases firstly and then decreases rapidly at the turning point around 1800 Pa. With the rate of powder feed increasing, the spheroidization rate of titanium powders increases firstly. When the powder feed rate is greater than 90.0 g/min, the spheroidization rate of titanium powders reduces rapidly as the powder feed rate increases. (authors)

Electrical conductivity of metal powders under pressure

Science.gov (United States)

Montes, J. M.; Cuevas, F. G.; Cintas, J.; Urban, P.

2011-12-01

A model for calculating the electrical conductivity of a compressed powder mass consisting of oxide-coated metal particles has been derived. A theoretical tool previously developed by the authors, the so-called `equivalent simple cubic system', was used in the model deduction. This tool is based on relating the actual powder system to an equivalent one consisting of deforming spheres packed in a simple cubic lattice, which is much easier to examine. The proposed model relates the effective electrical conductivity of the powder mass under compression to its level of porosity. Other physically measurable parameters in the model are the conductivities of the metal and oxide constituting the powder particles, their radii, the mean thickness of the oxide layer and the tap porosity of the powder. Two additional parameters controlling the effect of the descaling of the particle oxide layer were empirically introduced. The proposed model was experimentally verified by measurements of the electrical conductivity of aluminium, bronze, iron, nickel and titanium powders under pressure. The consistency between theoretical predictions and experimental results was reasonably good in all cases.

Study of nuclear fuel powders forming by axial compaction

International Nuclear Information System (INIS)

Fourcade, J.

2002-12-01

Nuclear fuel powders forming, although perfectly dominated, fail to make compacts without density gradients. Density heterogeneities induce diametric deformations during firing which force manufacturers to adjust shape with a high cost machining stage. Manufacturing process improvement is a major project to obtain perfectly shaped pellets and reduce their cost. One way of investigation of this project is the study of powders compaction mechanisms to understand and improve their behaviour. The goal of this study is to identify the main mechanisms linked with powder properties that act on pressing. An empirical model is developed to predict pellet deformations from a single compaction test. This model has to link powder properties with their compaction behaviour. Then, compaction tests identify the main mechanisms whereas a contact dynamic program is used to explain them. These works, done to improve the understanding in powders behaviour, focus on powders agglomeration state and macroscopic particles arrangement during the die filling stage. Actually, for granulated powders, granules cohesion act on the powder bed behaviour under pressure. The first particles arrangement is responsible for the first transfer directions into the powder and so for its transfer homogeneity and isotropy. As a consequence, the knowledge of all the macroscopic powder properties is essential to understand and improve the manufacturing process. Moreover, tests on UO 2 powders have shown that it is better to use granulated powders with spherical granules, short size distribution and granules cohesion according with compaction pressure to improve compact homogeneity of densification. (author)

Radiotreated cocoa powder for frozen elaboration

International Nuclear Information System (INIS)

Rodriguez Jorge, M.; Alvarez Gil, M.; Prieto Miranda, E.; Morales Valladares, M.

1995-01-01

The aim of the present papers is to study the possibilities of 2.0 kGy gamma radiotreated cocoa powder to be used in the elaboration of powder mixture for the preparation of chocolate frozen. Three industrial productions were carried out. Microbiological and organoleptic evaluations of the final product were performed. The results showed that the use of radurized cocoa powder in the frozen elaboration is feasible. A good hygienic quality of this product was obtained and no organoleptic alterations were detected [es

Preparation and utilization of metal oxide fine powder

Energy Technology Data Exchange (ETDEWEB)

Kim, Joon Soo; Jang, Hee Dong; Lim, Young Woong; Kim, Sung Don; Lee, Hi Sun; Lee, Hoo In; Kim, Chul Joo; Shim, Gun Joo; Jang, Dae Kyu [Korea Inst. of Geology Mining and Materials, Taejon (Korea, Republic of)

1995-12-01

Metal oxide fine powders finds many applications in industry as new materials. It is very much necessary for the development of such powders to improve the domestic industry. The purpose of present research is to develop a process for the preparation and utilization of metal oxide fine powder. This project is consisted of two main subjects. (1) Production of ultrafine metal oxide powder: Ultrafine metal oxide powder is defined as a metal oxide powder of less than 100 nanometer in particle size. Experiments for the control of particle size and distributions in the various reaction system and compared with results of (2 nd year research). Various reaction systems were adopted for the development of feasible process. Ultrafine particles could be prepared even higher concentration of TiCl{sub 4} and lower gas flowrate compared to TiCl{sub 4}-O{sub 2} system in the TiCl{sub 4}-Air-H{sub 2}O system. Ultrafine Al{sub 2}O{sub 3} powders also prepared with the change of concentration and gas flowrate. Experiments on the treatment of surface characteristics of ultrafine TiO{sub 2} powders were investigated using esterification and surface treating agents. A mathematical model that can predict the particle size and distribution was also developed. (2) Preparation of cerium oxide for high-grade polishing powder: Used cerium polishing powder was recycled for preparation of high grade cerium oxide polishing powder. Also, cerium hydroxide which was generated as by-product in processing of monazite ore was used as another material. These two materials were leached respectively by using acid, and the precipitate was gained in each leached solution by adjusting pH of the solution, and by selective crystallization. These precipitates were calcined to make high grade cerium oxide polishing powder. The effect of several experimental variables were investigated, and the optimum conditions were obtained through the experiments. (author). 81 refs., 49 figs., 27 tabs.

Descendant root volume varies as a function of root type: estimation of root biomass lost during uprooting in Pinus pinaster.

Science.gov (United States)

Danjon, Frédéric; Caplan, Joshua S; Fortin, Mathieu; Meredieu, Céline

2013-01-01

Root systems of woody plants generally display a strong relationship between the cross-sectional area or cross-sectional diameter (CSD) of a root and the dry weight of biomass (DWd) or root volume (Vd) that has grown (i.e., is descendent) from a point. Specification of this relationship allows one to quantify root architectural patterns and estimate the amount of material lost when root systems are extracted from the soil. However, specifications of this relationship generally do not account for the fact that root systems are comprised of multiple types of roots. We assessed whether the relationship between CSD and Vd varies as a function of root type. Additionally, we sought to identify a more accurate and time-efficient method for estimating missing root volume than is currently available. We used a database that described the 3D root architecture of Pinus pinaster root systems (5, 12, or 19 years) from a stand in southwest France. We determined the relationship between CSD and Vd for 10,000 root segments from intact root branches. Models were specified that did and did not account for root type. The relationships were then applied to the diameters of 11,000 broken root ends to estimate the volume of missing roots. CSD was nearly linearly related to the square root of Vd, but the slope of the curve varied greatly as a function of root type. Sinkers and deep roots tapered rapidly, as they were limited by available soil depth. Distal shallow roots tapered gradually, as they were less limited spatially. We estimated that younger trees lost an average of 17% of root volume when excavated, while older trees lost 4%. Missing volumes were smallest in the central parts of root systems and largest in distal shallow roots. The slopes of the curves for each root type are synthetic parameters that account for differentiation due to genetics, soil properties, or mechanical stimuli. Accounting for this differentiation is critical to estimating root loss accurately.

21 CFR 169.182 - Vanilla-vanillin powder.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Vanilla-vanillin powder. 169.182 Section 169.182... Dressings and Flavorings § 169.182 Vanilla-vanillin powder. (a) Vanilla-vanillin powder conforms to the... § 169.3(c) contained therein, the article also contains not more than 1 ounce of added vanillin. (b) The...

Shock-induced modification of inorganic powders

International Nuclear Information System (INIS)

Graham, R.A.; Morosin, B.; Venturini, E.L.; Beauchamp, E.K.; Hammetter, W.F.

1984-01-01

The results of studies performed to quantify the characteristics of TiO2, ZrO2 and Si3N4 powders exposed to explosive loading and post-shock analysis are reported. The shocks were produced with plane wave generators and explosive pads impinging on steel disks, a copper recovery fixture, and then the samples. Peak pressures of 13 and 17 GPa were attained, along with 40 GPz at the center of the powder cavity. Data are provided on the changes occurring during the explosive densification and X-ray and paramagnetic studies of the products. Only fractured disks were obtained in the trials. The shock-treated materials were more free flowing than the original powders, which were fluffy. Post-shock annealing was a significant feature of the treated powders

Spark-plasma sintering and mechanical property of mechanically alloyed NiAl powder compact and ball-milled (Ni+Al) mixed powder compact

International Nuclear Information System (INIS)

Kim, J.S.; Jang, Y.I.; Kwon, Y.S.; Kim, Y.D.; Ahn, I.S.

2001-01-01

Mechanically-alloyed NiAl powder and (Ni+Al) powder mixture prepared by ball-milling were sintered by spark-plasma sintering (SPS) process. Densification behavior and mechanical property were determined from the experimental results and analysis such as changes in linear shrinkage, shrinkage rate, microstructure, and phase during sintering process, Vicker's hardness and transverse rupture strength tests. Densification mechanisms for MA-NiAl powder compact and (Ni+Al) powder mixture were different from each other. While the former showed a rapid increase in densification rate only at higher temperature region of 800-900 o C, the latter revealed firstly a rapid increase in densification rate even at low temperature of 300 o C and a subsequent increase up to 500 o C. Densities of both powder compact (MA and mixture) sintered at 1150 o C for 5 min were 98 and above 99 %, respectively. Sintered bodies were composed mainly of NiAl phase with Ni 3 Al as secondary phase for both powders. Sintered body of MA-NiAl powder showed a very fine grain structure. Crystallite size determined by XRD result and the Sherrer's equation was approximately 80 nm. Vicker's hardness for the sintered bodies of (Ni+Al) powder mixture and MA-NiAl powder were 410±12 H v and 555±10 H v , respectively, whereas TRS values 1097±48 MPa and 1393±75 MPa. (author)

The effect of polymorphism on powder compaction and dissolution properties of chemically equivalent oxytetracycline hydrochloride powders.

Science.gov (United States)

Liebenberg, W; de Villiers, M M; Wurster, D E; Swanepoel, E; Dekker, T G; Lötter, A P

1999-09-01

In South Africa, oxytetracycline is identified as an essential drug; many generic products are on the market, and many more are being developed. In this study, six oxytetracycline hydrochloride powders were obtained randomly from manufacturers, and suppliers were compared. It was found that compliance to a pharmacopoeial monograph was insufficient to ensure the optimum dissolution performance of a simple tablet formulation. Comparative physicochemical raw material analysis showed no major differences with regard to differential scanning calorimetry (DSC), infrared (IR) spectroscopy, powder dissolution, and particle size. However, the samples could be divided into two distinct types with respect to X-ray powder diffraction (XRD) and thus polymorphism. The two polymorphic forms had different dissolution properties in water or 0.1 N hydrochloride acid. This difference became substantial when the dissolution from tablets was compared. The powders containing form A were less soluble than that containing form B.

Electro/powder separation process

International Nuclear Information System (INIS)

Dunn, J.P.

1977-01-01

A report is presented to introduce the ELECTRO/POWDER process to the P/M Industry. The process effectively uses electrostatic forces to convey, sort, meter, and blend fine powders. The major advantages of this separating process consist of the processing of primary particles, low particle energy due to particle velocity control and the pattern of particle movement over the sieve (vertical oscillation of particles above the sieve aperture). The report briefly describes the forces involved in both mechanical and sieving devices, with major emphasis on the operating principles of this process. Sieve separation of particulates is basically the result of two physical separating processes which occur simultaneously or independently; separation (dispersion) of particulates from each other and the size separation by passage through fixed apertures. In order to accomplish this goal, mechanical sieving devices utilize various motions to induce shear forces between the sieve surface and the particulates, and between the particulates themselves. It is noted that the ELECTRO/POWDER process is making steady progress in becoming an industrial tool for sieving and feeding of fine particles. Its potential extends into both the blending and admixing of powders, either by incorporating two opposing feeders, one being charged with the opposite polarity or by modifying the ELECTRO/SIEVE to incorporate more than one input and a solid electrode to replace the sieve electrode

A comparative study of the use of powder X-ray diffraction, Raman and near infrared spectroscopy for quantification of binary polymorphic mixtures of piracetam.

Science.gov (United States)

Croker, Denise M; Hennigan, Michelle C; Maher, Anthony; Hu, Yun; Ryder, Alan G; Hodnett, Benjamin K

2012-04-07

Diffraction and spectroscopic methods were evaluated for quantitative analysis of binary powder mixtures of FII(6.403) and FIII(6.525) piracetam. The two polymorphs of piracetam could be distinguished using powder X-ray diffraction (PXRD), Raman and near-infrared (NIR) spectroscopy. The results demonstrated that Raman and NIR spectroscopy are most suitable for quantitative analysis of this polymorphic mixture. When the spectra are treated with the combination of multiplicative scatter correction (MSC) and second derivative data pretreatments, the partial least squared (PLS) regression model gave a root mean square error of calibration (RMSEC) of 0.94 and 0.99%, respectively. FIII(6.525) demonstrated some preferred orientation in PXRD analysis, making PXRD the least preferred method of quantification. Copyright © 2012 Elsevier B.V. All rights reserved.

Fe-based nanocrystalline powder cores with ultra-low core loss

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiangyue, E-mail: wangxiangyue1986@163.com [China Iron and Steel Research Institute Group, Beijing 100081 (China); Center of Advanced Technology and Materials Co., Ltd., Beijing 100081 (China); Lu, Zhichao; Lu, Caowei; Li, Deren [China Iron and Steel Research Institute Group, Beijing 100081 (China); Center of Advanced Technology and Materials Co., Ltd., Beijing 100081 (China)

2013-12-15

Melt-spun amorphous Fe{sub 73.5}Cu{sub 1}Nb{sub 3}Si{sub 15.5}B{sub 7} alloy strip was crushed to make flake-shaped fine powders. The passivated powders by phosphoric acid were mixed with organic and inorganic binder, followed by cold compaction to form toroid-shaped bonded powder-metallurgical magnets. The powder cores were heat-treated to crystallize the amorphous structure and to control the nano-grain structure. Well-coated phosphate-oxide insulation layer on the powder surface decreased the the core loss with the insulation of each powder. FeCuNbSiB nanocrystalline alloy powder core prepared from the powder having phosphate-oxide layer exhibits a stable permeability up to high frequency range over 2 MHz. Especially, the core loss could be reduced remarkably. At the other hand, the softened inorganic binder in the annealing process could effectively improve the intensity of powder cores. - Highlights: • Fe-based nanocrystalline powder cores were prepared with low core loss. • Well-coated phosphate-oxide insulation layer on the powder surface decreased the core loss. • Fe-based nanocrystalline powder cores exhibited a stable permeability up to high frequency range over 2 MHz. • The softened inorganic binder in the annealing process could effectively improve the intensity of powder cores.

Characterizing pathways by which gravitropic effectors could move from the root cap to the root of primary roots of Zea mays

Science.gov (United States)

Moore, R.; McClelen, C. E.

1989-01-01

Plasmodesmata linking the root cap and root in primary roots Zea mays are restricted to approx. 400 protodermal cells bordering approx. 110000 microns2 of the calyptrogen of the root cap. This area is less than 10% of the cross-sectional area of the root-tip at the cap junction. Therefore, gravitropic effectors moving from the root cap to the root can move symplastically only through a relatively small area in the centre of the root. Decapped roots are non-responsive to gravity. However, decapped roots whose caps are replaced immediately after decapping are strongly graviresponsive. Thus, gravicurvature occurs only when the root cap contacts the root, and symplastic continuity between the cap and root is not required for gravicurvature. Completely removing mucilage from the root tip renders the root non-responsive to gravity. Taken together, these data suggest that gravitropic effectors move apoplastically through mucilage from the cap to the root.

Preparation of superconducting powders by freeze-drying

International Nuclear Information System (INIS)

Johnson, S.M.; Gusman, M.I.; Rowcliffe, D.J.; Geballe, T.H.; Sun, J.Z.

1987-01-01

A method of preparing superconducting powders by freeze-drying is described. Powders produced by this method are homogeneous, have high purities, and are very reactive. Materials sintered from these powders have densities up to 89% of the theoretical density, and exhibit very sharp resistivity drops and large Meissner effects. The microstructure of the materials is very sensitive to the sintering temperature

Food powders flowability characterization: theory, methods, and applications.

Science.gov (United States)

Juliano, Pablo; Barbosa-Cánovas, Gustavo V

2010-01-01

Characterization of food powders flowability is required for predicting powder flow from hoppers in small-scale systems such as vending machines or at the industrial scale from storage silos or bins dispensing into powder mixing systems or packaging machines. This review covers conventional and new methods used to measure flowability in food powders. The method developed by Jenike (1964) for determining hopper outlet diameter and hopper angle has become a standard for the design of bins and is regarded as a standard method to characterize flowability. Moreover, there are a number of shear cells that can be used to determine failure properties defined by Jenike's theory. Other classic methods (compression, angle of repose) and nonconventional methods (Hall flowmeter, Johanson Indicizer, Hosokawa powder tester, tensile strength tester, powder rheometer), used mainly for the characterization of food powder cohesiveness, are described. The effect of some factors preventing flow, such as water content, temperature, time consolidation, particle composition and size distribution, is summarized for the characterization of specific food powders with conventional and other methods. Whereas time-consuming standard methods established for hopper design provide flow properties, there is yet little comparative evidence demonstrating that other rapid methods may provide similar flow prediction.

Exploring Oven-drying Technique in Producing Pineapple Powder

Directory of Open Access Journals (Sweden)

Cyril John A. Domingo

2017-11-01

Full Text Available Pineapple puree and juice of 11 to 12 °Brix were used to obtain pineapple powder using oven-drying technique. Addition of maltodextrin in treatments 2 and 4 yielded good quality powder, however addition of sugar and maltodextrin in treatments 1 and 3 resulted to sticky product which was processed to pineapple leather. Treatment 2 composed of pineapple puree and maltodextrin resulted to significantly higher powder recovery compared with treatment 4 which composed of pineapple juice and maltodextrin. The solubility of pineapple powder improved as maltodextrin concentration is increased from 40.00 % to 60.00 %.Addition of maltodextrin also reduced stickiness of the final product. An instant pineapple powder of 5.47 and 5.33 % moisture content could be produced by oven-drying.This level of moisture content will prohibit bacterial growth in the pineapple powder but may have mold or yeast growth with increase storage period at environments with high humidity. Molds were observed on the 17th day at 89.00 % relative humidity as exhibited by the moisture sorption isotherm data. This suggests that appropriate packaging with moisture barrier is recommended for pineapple powder. This study showedthat by using appropriate ratio of juice, puree, and maltodextrin and appropriate oven drying conditions, a good oven-dried pineapple powder could be obtained.

Root anatomy, morphology, and longevity among root orders in Vaccinium corymbosum (Ericaceae).

Science.gov (United States)

Valenzuela-Estrada, Luis R; Vera-Caraballo, Vivianette; Ruth, Leah E; Eissenstat, David M

2008-12-01

Understanding root processes at the whole-plant or ecosystem scales requires an accounting of the range of functions within a root system. Studying root traits based on their branching order can be a powerful approach to understanding this complex system. The current study examined the highly branched root system of the ericoid plant, Vaccinium corymbosum L. (highbush blueberry) by classifying its root orders with a modified version of the morphometric approach similar to that used in hydrology for stream classification. Root anatomy provided valuable insight into variation in root function across orders. The more permanent portion of the root system occurred in 4th- and higher-order roots. Roots in these orders had radial growth; the lowest specific root length, N:C ratios, and mycorrhizal colonization; the highest tissue density and vessel number; and the coarsest root diameter. The ephemeral portion of the root system was mainly in the first three root orders. First- and 2nd-order roots were nearly anatomically identical, with similar mycorrhizal colonization and diameter, and also, despite being extremely fine, median lifespans were not very short (115-120 d; estimated with minirhizotrons). Our research underscores the value of examining root traits by root order and its implications to understanding belowground processes.

Ternary ceramic thermal spraying powder and method of manufacturing thermal sprayed coating using said powder

Energy Technology Data Exchange (ETDEWEB)

Vogli, Evelina; Sherman, Andrew J.; Glasgow, Curtis P.

2018-02-06

The invention describes a method for producing ternary and binary ceramic powders and their thermal spraying capable of manufacturing thermal sprayed coatings with superior properties. Powder contain at least 30% by weight ternary ceramic, at least 20% by weight binary molybdenum borides, at least one of the binary borides of Cr, Fe, Ni, W and Co and a maximum of 10% by weight of nano and submicro-sized boron nitride. The primary crystal phase of the manufactured thermal sprayed coatings from these powders is a ternary ceramic, while the secondary phases are binary ceramics. The coatings have extremely high resistance against corrosion of molten metal, extremely thermal shock resistance and superior tribological properties at low and at high temperatures.

The quantitative characterization of sintering of urania powders

International Nuclear Information System (INIS)

Das, P.; Kulkarni, U.D.

1981-01-01

This paper presents a unified approach towards characterization of the sintering behaviour of UO 2 powders in terms of their extrinsic properties. Empirical equations connecting the sintering index with various powder parameters have been set up. The influence of various powder parameters, either individually or as dimensionless/dimensional groups, on the sintering behaviour has been studied. The relative importance of these factors has also been analysed. A good polynomial fit has been obtained for variation of sintering index with some of the powder parameters and dimensionless/dimensional groups. The equations are expected to provide a good basis for assessing the sinterability of UO 2 powders. (Auth.)

Characterization and Sintering of Armstrong Process Titanium Powder

Science.gov (United States)

Xu, Xiaoyan; Nash, Philip; Mangabhai, Damien

2017-04-01

Titanium and titanium alloys have a high strength to weight ratio and good corrosion resistance but also need longer time and have a higher cost on machining. Powder metallurgy offers a viable approach to produce near net-shape complex components with little or no machining. The Armstrong titanium powders are produced by direct reduction of TiCl4 vapor with liquid sodium, a process which has a relatively low cost. This paper presents a systematic research on powder characterization, mechanical properties, and sintering behavior and of Armstrong process powder metallurgy, and also discusses the sodium issue, and the advantages and disadvantages of Armstrong process powders.

Advances in beryllium powder consolidation simulations

International Nuclear Information System (INIS)

Reardon, B.J.

1998-01-01

A fuzzy logic based multiobjective genetic algorithm (GA) is introduced and the algorithm is used to optimize micromechanical densification modeling parameters for warm isopressed beryllium powder, HIPed copper powder and CIPed/sintered and HIPed tantalum powder. In addition to optimizing the main model parameters using the experimental data points as objective functions, the GA provides a quantitative measure of the sensitivity of the model to each parameter, estimates the mean particle size of the powder, and determines the smoothing factors for the transition between stage 1 and stage 2 densification. While the GA does not provide a sensitivity analysis in the strictest sense, and is highly stochastic in nature, this method is reliable and reproducible in optimizing parameters given any size data set and determining the impact on the model of slight variations in each parameter

Strain-enhanced sintering of iron powders

Energy Technology Data Exchange (ETDEWEB)

Amador, D.R.; Torralba, J.M. [Universidad Carlos III de Madrid, Departamento de Ciencias de Materiales e Ingenieria Metalurgica, Leganes, Madrid (Spain); Monge, M.A.; Pareja, R. [Universidad Carlos III de Madrid, Departamento de Fisica, Madrid (Spain)

2005-02-01

Sintering of ball-milled and un-milled Fe powders has been investigated using dilatometry, X-ray, density, and positron annihilation techniques. A considerable sintering enhancement is found in milled powders showing apparent activation energies that range between 0.44 and 0.80 eV/at. The positron annihilation results, combined with the evolution of the shrinkage rate with sintering temperature, indicate generation of lattice defects during the sintering process of milled and un-milled powders. The sintering enhancement is attributed to pipe diffusion along the core of moving dislocations in the presence of the vacancy excess produced by plastic deformation. Positron annihilation results do not reveal the presence of sintering-induced defects in un-milled powders sintered above 1200 K, the apparent activation energy being in good agreement with that for grain-boundary diffusion in {gamma}-Fe. (orig.)

Powder diffractometry

International Nuclear Information System (INIS)

Doucet, J.

1983-01-01

The new possibilities openned by the synchrotron radiation in the powder diffractometry techniques are presented. This technique is described in a general manner and some aspects which can be developed with the use of the synchrotron radiation are analyzed. (L.C.) [pt

Powder metallurgy techniques in nuclear technology

International Nuclear Information System (INIS)

Mardon, P.G.

1983-01-01

The nuclear application of conventional powder metallurgy routes is centred on the fabrication of ceramic fuels. The stringent demands in terms of product performance required by the nuclear industry militate against the use of conventional powder metallurgy to produce metallic components such as the fuel cladding. However, the techniques developed in powder metallurgy find widespread application throughout nuclear technology. Illustrations of the use of these techniques are given in the fields of absorber materials, ceramic cladding materials, oxide fuels, cermet fuels, and the disposal of highly active waste. (author)

Plasma metallization of refractory carbide powders

International Nuclear Information System (INIS)

Koroleva, E.B.; Klinskaya, N.A.; Rybalko, O.F.; Ugol'nikova, T.A.

1986-01-01

The effect of treatment conditions in plasma on properties of produced metallized powders of titanium, tungsten and chromium carbides with the main particle size of 40-80 μm is considered. It is shown that plasma treatment permits to produce metallized powders of carbide materials with the 40-80 μm particle size. The degree of metallization, spheroidization, chemical and phase composition of metallized carbide powders are controlled by dispersivity of the treated material, concentration of a metal component in the treated mixtures, rate of plasma flow and preliminary spheroidization procedure

Net shape powder processing of aluminium

International Nuclear Information System (INIS)

Schaffer, G.B.

2000-01-01

The increasing interest in light weight materials coupled to the need for cost-effective processing have combined to create a significant opportunity for aluminium powder metallurgy. Net shape processing of aluminium using the classical press-and-sinter powder metallurgy technique is a unique and important metal-forming method which is cost effective in producing complex parts at, or very close to, final dimensions. This paper provides an overview of the net shape powder processing of aluminium. Current research is critically reviewed and the future potential is briefly considered

Application of permanent magnets made from NdFeB powder and from mixtures of powders in DC motors

International Nuclear Information System (INIS)

Slusarek, B.; Dudzikowski, I.

2002-01-01

The paper presents the influence of magnetic properties of applied permanent magnets on the characteristics of DC motors excited with these magnets. In the factory-produced DC motors, excited with sintered ferrite magnets, authors replaced ferrite magnets with the dielectromagnets from NdFeB powder and from different mixtures of NdFeB and ferrite powders. The paper shows the increase of the power of the resultant DC motors according to the powders' content

Inhibition of VEGF: a novel mechanism to control angiogenesis by Withania somnifera's key metabolite Withaferin A.

Science.gov (United States)

Saha, Sanjib; Islam, Md Khirul; Shilpi, Jamil A; Hasan, Shihab

2013-01-01

Angiogenesis, or new blood vessel formation from existing one, plays both beneficial and detrimental roles in living organisms in different aspects. Vascular endothelial growth factor (VEGF), a signal protein, well established as key regulator of vasculogenesis and angiogenesis. VEGF ensures oxygen supply to the tissues when blood supply is not adequate, or tissue environment is in hypoxic condition. Limited expression of VEGF is necessary, but if it is over expressed, then it can lead to serious disease like cancer. Cancers that have ability to express VEGF are more efficient to grow and metastasize because solid cancers cannot grow larger than a limited size without adequate blood and oxygen supply. Anti-VEGF drugs are already available in the market to control angiogenesis, but they are often associated with severe side-effects like fetal bleeding and proteinuria in the large number of patients. To avoid such side-effects, new insight is required to find potential compounds as anti-VEGF from natural sources. In the present investigation, molecular docking studies were carried out to find the potentiality of Withaferin A, a key metabolite of Withania somnifera, as an inhibitor of VEGF. Molecular Docking studies were performed in DockingServer and SwissDock. Bevacizumab, a commercial anti-VEGF drug, was used as reference to compare the activity of Withaferin A. X-ray crystallographic structure of VEGF, was retrieved from Protein Data Bank (PDB), and used as drug target protein. Structure of Withaferin A and Bevacizumab was obtained from PubChem and ZINC databases. Molecular visualization was performed using UCSF Chimera. Withaferin A showed favorable binding with VEGF with low binding energy in comparison to Bevacizumab. Molecular Docking studies also revealed potential protein-ligand interactions for both Withaferin A and Bevacizumab. Conclusively our results strongly suggest that Withaferin A is a potent anti-VEGF agent as ascertained by its potential

OpenSimRoot: widening the scope and application of root architectural models.

Science.gov (United States)

Postma, Johannes A; Kuppe, Christian; Owen, Markus R; Mellor, Nathan; Griffiths, Marcus; Bennett, Malcolm J; Lynch, Jonathan P; Watt, Michelle

2017-08-01

OpenSimRoot is an open-source, functional-structural plant model and mathematical description of root growth and function. We describe OpenSimRoot and its functionality to broaden the benefits of root modeling to the plant science community. OpenSimRoot is an extended version of SimRoot, established to simulate root system architecture, nutrient acquisition and plant growth. OpenSimRoot has a plugin, modular infrastructure, coupling single plant and crop stands to soil nutrient and water transport models. It estimates the value of root traits for water and nutrient acquisition in environments and plant species. The flexible OpenSimRoot design allows upscaling from root anatomy to plant community to estimate the following: resource costs of developmental and anatomical traits; trait synergisms; and (interspecies) root competition. OpenSimRoot can model three-dimensional images from magnetic resonance imaging (MRI) and X-ray computed tomography (CT) of roots in soil. New modules include: soil water-dependent water uptake and xylem flow; tiller formation; evapotranspiration; simultaneous simulation of mobile solutes; mesh refinement; and root growth plasticity. OpenSimRoot integrates plant phenotypic data with environmental metadata to support experimental designs and to gain a mechanistic understanding at system scales. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Time resolved fluorescence of cow and goat milk powder

Science.gov (United States)

Brandao, Mariana P.; de Carvalho dos Anjos, Virgílio; Bell., Maria José V.

2017-01-01

Milk powder is an international dairy commodity. Goat and cow milk powders are significant sources of nutrients and the investigation of the authenticity and classification of milk powder is particularly important. The use of time-resolved fluorescence techniques to distinguish chemical composition and structure modifications could assist develop a portable and non-destructive methodology to perform milk powder classification and determine composition. This study goal is to differentiate milk powder samples from cows and goats using fluorescence lifetimes. The samples were excited at 315 nm and the fluorescence intensity decay registered at 468 nm. We observed fluorescence lifetimes of 1.5 ± 0.3, 6.4 ± 0.4 and 18.7 ± 2.5 ns for goat milk powder; and 1.7 ± 0.3, 6.9 ± 0.2 and 29.9 ± 1.6 ns for cow's milk powder. We discriminate goat and cow powder milk by analysis of variance using Fisher's method. In addition, we employed quadratic discriminant analysis to differentiate the milk samples with accuracy of 100%. Our results suggest that time-resolved fluorescence can provide a new method to the analysis of powder milk and its composition.

Slip casting nano-particle powders for making transparent ceramics

Science.gov (United States)

Kuntz, Joshua D [Livermore, CA; Soules, Thomas F [Livermore, CA; Landingham, Richard Lee [Livermore, CA; Hollingsworth, Joel P [Oakland, CA

2011-04-12

A method of making a transparent ceramic including the steps of providing nano-ceramic powders in a processed or unprocessed form, mixing the powders with de-ionized water, the step of mixing the powders with de-ionized water producing a slurry, sonifing the slurry to completely wet the powder and suspend the powder in the de-ionized water, separating very fine particles from the slurry, molding the slurry, and curing the slurry to produce the transparent ceramic.

Powder technology

International Nuclear Information System (INIS)

Agueda, Horacio

1989-01-01

Powder technology is experiencing nowadays a great development and has broad application in different fields: nuclear energy, medicine, new energy sources, industrial and home artifacts, etc. Ceramic materials are of daily use as tableware and also in the building industry (bricks, tiles, etc.). However, in machine construction its utilization is not so common. The same happens with metals: powder metallurgy is employed less than traditional metal forming techniques. Both cases deal with powder technology and the forming techniques as far as the final consolidation through sintering processes are very similar. There are many different methods and techniques in the forming stage: cold-pressing, slip casting, injection molding, extrusion molding, isostatic pressing, hot-pressing (which involves also the final consolidation step), etc. This variety allows to obtain almost any desired form no matter how complex it could be. Some applications are very specific as in the case of UO 2 pellets (used as nuclear fuels) but with the same technique and other materials, it is possible to manufacture a great number of different products. This work shows the characteristics and behaviour of two magnetic ceramic materials (ferrites) fabricated in the laboratory of the Applied Research Division of the Bariloche Atomic Center for different purposes. Other materials and products made with the same method are also mentioned. Likewise, densities and shrinkage obtained by different methods of forming (cold-pressing, injection molding, slip casting and extrusion molding) using high-purity alumina (99.5% Al 2 O 3 ). Finally, different applications of such methods are given. (Author) [es

Investigation of pressing of molybdenum powder compacts

International Nuclear Information System (INIS)

Mymrin, S.A.; Kuznetsov, V.Eh.; Yampol'skij, M.L.; Leonov, S.A.; Mikhridinov, R.M.; Korzukhin, V.A.

1990-01-01

Results of an experimental investigation into pressing of compacts of MCh type molybdenum powders using the industrial equipment are presented. To measure the density of powder molybdenum billets a radioisotopic density meter with cesium-137 is used as radioactive gamma radiation source. The dependence of the produced billet density on the specific compacting pressure at different values of the powder bulk density is ascertained

Cryomilling of Thermoplastic Powder for Prepreg Applications

Science.gov (United States)

2013-09-01

Cryomilling of Thermoplastic Powder for Prepreg Applications by Brian Parquette, Anit Giri, Daniel J. O’Brien, Sarah Brennan, Kyu Cho, and...MD 21005-5066 ARL-TR-6591 September 2013 Cryomilling of Thermoplastic Powder for Prepreg Applications Brian Parquette and Sarah Brennan...COVERED (From - To) 1 March 2012–30 May 2013 4. TITLE AND SUBTITLE Cryomilling of Thermoplastic Powder for Prepreg Applications 5a. CONTRACT

Environment friendly route of iron oxide nanoparticles from Zingiber officinale (ginger) root extract

Science.gov (United States)

Xin Hui, Yau; Yi Peng, Teoh; Wei Wen, Liu; Zhong Xian, Ooi; Peck Loo, Kiew

2016-11-01

Iron oxide nanoparticles were prepared from the reaction between the Zingiber officinale (ginger) root extracts and ferric chloride solution at 50°C for 2 h in mild stirring condition. The synthesized powder forms of nanoparticles were further characterized by using UV-Vis spectroscopy and X-ray Diffraction spectrometry. UV-Vis analysis shows the absorption peak of iron oxide nanoparticles is appeared at 370 nm. The calculation of crystallite size from the XRD showed that the average particle size of iron oxide nanoparticles was 68.43 nm. Therefore, this eco-friendly technique is low cost and large scale nanoparticles synthesis to fulfill the demand of various applications.

Light as stress factor to plant roots - case of root halotropism.

Science.gov (United States)

Yokawa, Ken; Fasano, Rossella; Kagenishi, Tomoko; Baluška, František

2014-01-01

Despite growing underground, largely in darkness, roots emerge to be very sensitive to light. Recently, several important papers have been published which reveal that plant roots not only express all known light receptors but also that their growth, physiology and adaptive stress responses are light-sensitive. In Arabidopsis, illumination of roots speeds-up root growth via reactive oxygen species-mediated and F-actin dependent process. On the other hand, keeping Arabidopsis roots in darkness alters F-actin distribution, polar localization of PIN proteins as well as polar transport of auxin. Several signaling components activated by phytohormones are overlapping with light-related signaling cascade. We demonstrated that the sensitivity of roots to salinity is altered in the light-grown Arabidopsis roots. Particularly, light-exposed roots are less effective in their salt-avoidance behavior known as root halotropism. Here we discuss these new aspects of light-mediated root behavior from cellular, physiological and evolutionary perspectives.

Cerebroprotective Actions of Triticum aestivum Linn Powder and Bauhinia purpurea Flower Powder in Surgically Induced Cerebral Infraction in Rats.

Science.gov (United States)

Annapurna, Akula; Vishala, Thonangi C; Bitra, Veera R; Rapaka, Deepthi; Shaik, Asmath

2018-01-01

The prime objective of this study is to evaluate the cerebroprotective actions of Triticum aestivum (wheatgrass) powder and Bauhinia purpurea flower (dev kanchan) powder against the experimentally induced global ischemia reperfusion injury in rats. In the first phase of the studies, 1 h before the surgical procedure, the Wistar rats were orally served with varied doses of wheatgrass powder (5, 10, 30, and 100 μg/kg) and Bauhinia flower powder (30, 100, 200, and 300 μg/kg), respectively. The ischemia was induced by 30-min bilateral carotid artery occlusion in succession to reperfusion for 4 h. It was proved that the wheatgrass powder and Bauhinia flower powder yielded a significant, dose-dependent cerebroprotection in terms of reduction in cerebral infarct size when compared with the control group. Coming to the second phase of the studies, a certain potential dose of 10 μg/kg of wheatgrass and 200 μg/kg of Bauhinia flower powders was selected keeping the protective action in view, and the animals were treated for 15 days. The major findings of the study are that wheatgrass and Bauhinia flower powders significantly augmented the magnitude of the antioxidant enzymes, viz., super oxide dismutase and catalase, and further reduced the levels of lipid peroxidation. The present study clearly showed that the wheatgrass powder and Bauhinia flower powder possess significant antioxidant properties that may act as a key ingredient in various ayurvedic preparations for the treatment of various diseases like cerebral ischemic reperfusion injury. The wheat grass contains high amount of bioflavonoids, alkaloids, SOD etc which are responsible for anti oxidant activity.The Bauhinia purpurea contains glycosides, flavonoids and also plays a major role in DPPH activity which is responsible for anti oxidant activity.The wheat grass (10 mg/kg) and bauhinia (200 mg/kg) significantly(P bauhinia (200 mg/kg) significantly (P <0.0001) reduced the lipid peroxidation (MDA) and increased SOD

Free radical interactions between raw materials in dry soup powder.

Science.gov (United States)

Raitio, Riikka; Orlien, Vibeke; Skibsted, Leif H

2011-12-01

Interactions at the free radical level were observed between dry ingredients in cauliflower soup powder, prepared by dry mixing of ingredients and rapeseed oil, which may be of importance for quality deterioration of such dry food products. The free radical concentrations of cauliflower soup powder, obtained by electron spin resonance (ESR) spectroscopy, rapidly become smaller during storage (40°C and relative humidity of 75%) than the calculated concentrations of free radicals based on the free radical concentrations of the powder ingredients used to make the soup powder and stored separately under similar conditions. Similarly, free radical concentrations decreased faster when any combination of two powder ingredients (of the three major ingredients of the soup powder) were mixed together and stored at 50°C for 1week than when each powder component was stored separately. Furthermore, yeast extract powder was found to play a key role when free radical interactions between powder ingredients occurred. The incubation of rapeseed oil with powder ingredients at 45°C for 24h, indicated the ability of cauliflower powder to increase the concentration of hydroperoxides in rapeseed oil, while yeast extract powder was found to prevent this hydroperoxide formation. Copyright © 2011 Elsevier Ltd. All rights reserved.

effects of different concentrations of auxins on rooting and root

African Journals Online (AJOL)

Preferred Customer

ABSTRACT: The effect of auxins and their different concentrations on rooting and root ... primary root length and the longest primary root was recorded with the ... ceuticals, lubricants, foods, electrical insulators, .... stem cuttings of jojoba treated with IBA and NAA, .... increasing cell division and enlargement at each.

Characterization of Metal Powders Used for Additive Manufacturing.

Science.gov (United States)

Slotwinski, J A; Garboczi, E J; Stutzman, P E; Ferraris, C F; Watson, S S; Peltz, M A

2014-01-01

Additive manufacturing (AM) techniques can produce complex, high-value metal parts, with potential applications as critical parts, such as those found in aerospace components. The production of AM parts with consistent and predictable properties requires input materials (e.g., metal powders) with known and repeatable characteristics, which in turn requires standardized measurement methods for powder properties. First, based on our previous work, we assess the applicability of current standardized methods for powder characterization for metal AM powders. Then we present the results of systematic studies carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to structure and chemistry, including X-ray diffraction, energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, and X-Ray photoelectron spectroscopy were also employed. The results of these analyses show how virgin powder changes after being exposed to and recycled from one or more Direct Metal Laser Sintering (DMLS) additive manufacturing build cycles. In addition, these findings can give insight into the actual additive manufacturing process.

Characterization of Metal Powders Used for Additive Manufacturing

Science.gov (United States)

Slotwinski, JA; Garboczi, EJ; Stutzman, PE; Ferraris, CF; Watson, SS; Peltz, MA

2014-01-01

Additive manufacturing (AM) techniques1 can produce complex, high-value metal parts, with potential applications as critical parts, such as those found in aerospace components. The production of AM parts with consistent and predictable properties requires input materials (e.g., metal powders) with known and repeatable characteristics, which in turn requires standardized measurement methods for powder properties. First, based on our previous work, we assess the applicability of current standardized methods for powder characterization for metal AM powders. Then we present the results of systematic studies carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to structure and chemistry, including X-ray diffraction, energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, and X-Ray photoelectron spectroscopy were also employed. The results of these analyses show how virgin powder changes after being exposed to and recycled from one or more Direct Metal Laser Sintering (DMLS) additive manufacturing build cycles. In addition, these findings can give insight into the actual additive manufacturing process. PMID:26601040

Seedling root targets

Science.gov (United States)

Diane L. Haase

2011-01-01

Roots are critical to seedling performance after outplanting. Although root quality is not as quick and simple to measure as shoot quality, target root characteristics should be included in any seedling quality assessment program. This paper provides a brief review of root characteristics most commonly targeted for operational seedling production. These are: root mass...

Some aspects of UO{sub 2} powder production

Energy Technology Data Exchange (ETDEWEB)

Balakrishna, P; Asnani, C K; Prabhakar Rao, L; Kartha, R M; Pillai, P K.M. [Nuclear Fuel Complex, Hyderabad (India)

1994-06-01

UO{sub 2} powder is being produced in a chemical plant from enriched UF{sub 6} and supplied to the pelletizing plant. Small quantities of scrap UO{sub 2} received back from the pelletizing plant are also recycled in the chemical plant to produce UO{sub 2} powder. The powder should be of a consistently high quality so as to finally yield high density sintered pellets with minimum rejection. The final yield of acceptable finished pellets depends on the quality of the powder in the chemical plant as well as the quality of pressing in the pelletizing plant. In this paper, some examples of measures adopted for achieving good quality powder production are presented. (author). 9 refs., 2 figs.

Introduction to powder metallurgy processes for titanium manufacturing

International Nuclear Information System (INIS)

Esteban, P. G.; Bolzoni, L.; Ruiz-Navas, E. M.; Gordo, E.

2011-01-01

The development of new extraction processes to produce titanium in powder form leads Powder Metallurgy to an advantage position among the manufacturing processes for titanium. The cost reduction of base material, coupled with the economy of the powder metallurgy processes, give titanium industry the chance to diversify its products, which could lead to production volumes able to stabilise the price of the metal. This work reviews some of the Powder Metallurgy techniques for the manufacturing of titanium parts, and describes the two typical approaches for titanium manufacturing: Blending Elemental and Prealloyed Powders. Among others, conventional pressing and sintering are described, which are compared with cold and hot isostatic pressing techniques. Real and potential applications are described. (Author) 71 refs.

Effect of Root Moisture Content and Diameter on Root Tensile Properties

Science.gov (United States)

Yang, Yuanjun; Chen, Lihua; Li, Ning; Zhang, Qiufen

2016-01-01

The stabilization of slopes by vegetation has been a topical issue for many years. Root mechanical characteristics significantly influence soil reinforcement; therefore it is necessary to research into the indicators of root tensile properties. In this study, we explored the influence of root moisture content on tensile resistance and strength with different root diameters and for different tree species. Betula platyphylla, Quercus mongolica, Pinus tabulaeformis, and Larix gmelinii, the most popular tree species used for slope stabilization in the rocky mountainous areas of northern China, were used in this study. A tensile test was conducted after root samples were grouped by diameter and moisture content. The results showedthat:1) root moisture content had a significant influence on tensile properties; 2) slightly loss of root moisture content could enhance tensile strength, but too much loss of water resulted in weaker capacity for root elongation, and consequently reduced tensile strength; 3) root diameter had a strong positive correlation with tensile resistance; and4) the roots of Betula platyphylla had the best tensile properties when both diameter and moisture content being controlled. These findings improve our understanding of root tensile properties with root size and moisture, and could be useful for slope stabilization using vegetation. PMID:27003872

Characterization of powdered fish heads for bone graft biomaterial applications.

Science.gov (United States)

Oteyaka, Mustafa Ozgür; Unal, Hasan Hüseyin; Bilici, Namık; Taşçı, Eda

2013-01-01

The aim of this study was to define the chemical composition, morphology and crystallography of powdered fish heads of the species Argyrosomus regius for bone graft biomaterial applications. Two sizes of powder were prepared by different grinding methods; Powder A (coarse, d50=68.5 µm) and Powder B (fine, d50=19.1 µm). Samples were analyzed using X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), thermogravimetry (TG), and energy dispersive X-ray spectroscopy (EDS). The powder was mainly composed of aragonite (CaCO3) and calcite (CaCO3). The XRD pattern of Powder A and B matched standard aragonite and calcite patterns. In addition, the calcium oxide (CaO) phase was found after the calcination of Powder A. Thermogravimetry analysis confirmed total mass losses of 43.6% and 47.3% in Powders A and B, respectively. The microstructure of Powder A was mainly composed of different sizes and tubular shape, whereas Powder B showed agglomerated particles. The high quantity of CaO and other oxides resemble the chemical composition of bone. In general, the powder can be considered as bone graft after transformation to hydroxyapatite phase.

Compaction of amorphous iron–boron powder

DEFF Research Database (Denmark)

Hendriksen, Peter Vang; Mørup, Steen; Koch, Christian

1993-01-01

Large scale practical use of bulk amorphous alloys requires the capability of molding the material to a desired design, for instance by compaction of an amorphous powder. This is a difficult task because the sintering temperature is limited by the crystallization temperature of the alloy.1 Here we......, should facilitate a compaction. The passivation layer, however, impedes a compaction. Isostatic pressing at 540 K at a pressure of 200 MPa clearly illustrated this; pellets pressed from passivated powder were much more brittle than pellets pressed from unpassivated powder. The density of the pellets...... was very low ([approximately-equal-to]25% of the density of bulk FeB). We have designed a die for uniaxial pressing in which the compaction can be performed without exposing the powder to air and have obtained densities larger than 60% of that of bulk FeB. We have reported studies of the dependence...

Properties of magnetic nickel/porous-silicon composite powders

Directory of Open Access Journals (Sweden)

Toshihiro Nakamura

2012-09-01

Full Text Available The magnetic and photoluminescence (PL properties of nickel/porous-silicon (Ni/PSi composite powders are investigated. Ni/PSi composite powders are prepared by stain etching of Si powder in a HF/HNO3 solution followed by electroless plating of Ni nanoparticles on the stain-etched PSi powder in a NiCl2 solution. The Ni/PSi powders exhibit hydrophillicity, superparamagnetism caused by the deposited Ni nanoparticles, and orange-red PL owing to the nanostructured PSi surface. The degree of magnetization decreases with increasing Ni plating time, indicating its dependence on the size of the Ni nanoparticles. The Ni/PSi composite powders also show a stronger magnetization as compared to that of the Ni-particle-plated Si powder. The stronger magnetization results from the larger surface area of PSi. The PL intensity, peak wavelength, and lifetime of Ni/PSi are strongly dependent on the NiCl2 concentration. This dependence is due to the different thickness of the oxide overlayer on the PSi surface formed during the Ni plating process. The existence of the oxide overlayer also results in a small change in the PL intensity against excitation time.

Dispersion-strengthened Aluminium Products Manufactured by Powder Blending

DEFF Research Database (Denmark)

Hansen, Niels

1969-01-01

Detailed experiments carried out to examine relationship between microstructure and mechanical properties of powder-blended aluminum products are reported; their results as well as structural studies by transmission electron microscopy and tensile-and creep- testing, are given; as dispersed phase......, various oxide powders were selected on criterion that during manufacturing no reaction must taken place between metal and oxide phase; strength of powder-blended aluminum products increases and elongation decreases with decreasing particle size of aluminum powder and with increasing concentration of oxide...

Novel Fe-based nanocrystalline powder cores with excellent magnetic properties produced using gas-atomized powder

Science.gov (United States)

Chang, Liang; Xie, Lei; Liu, Min; Li, Qiang; Dong, Yaqiang; Chang, Chuntao; Wang, Xin-Min; Inoue, Akihisa

2018-04-01

FeSiBPNbCu nanocrystalline powder cores (NPCs) with excellent magnetic properties were fabricated by cold-compaction of the gas-atomized amorphous powder. Upon annealing at the optimum temperature, the NPCs showed excellent magnetic properties, including high initial permeability of 88, high frequency stability up to 1 MHz with a constant value of 85, low core loss of 265 mW/cm3 at 100 kHz for Bm = 0.05 T, and superior DC-bias permeability of 60% at a bias field of 100 Oe. The excellent magnetic properties of the present NPCs could be attributed to the ultrafine α-Fe(Si) phase precipitated in the amorphous matrix and the use of gas-atomized powder coated with a uniform insulation layer.

Mudas de melancia produzidas com substrato à base de pó de coco e soluções nutritivas Watermelon seedlings produced with coconut powder and nutrient solutions

Directory of Open Access Journals (Sweden)

Anamaria RP Ramos

2012-06-01

mudas de melancia, em relação ao crescimento e status nutricional.The choice of substrate is one of the most important stages for the seedlings production and must take into account the nutritional requirements of cultivated species. Thus, the objective was to evaluate the substrate using coconut dust associated with nutrient solutions to produce seedlings of watermelon. The experiment was carried out at Embrapa Semi-Arid in Petrolina, Pernambuco state, Brazil, in a greenhouse in a completely randomized design with ten replications in a factorial arrangement 2 x 10 (cultivars of watermelon and substrates. The cultivars used were: Opara and Top Gun. The coconut fiber was associated with nutrient solutions as follows: T1= control treatment composed of the commercial organic substrate Plantmax® (SC, T2= coconut powder (PC, T3= coconut powder + melon solution (PC+SM, T4= coconut powder + solution of Hoagland and Arnon 12.5% (12.5% PC+HS, T5= coconut powder + solution of Hoagland and Arnon 25% (PC+HS 25%, T6= coconut powder + solution of Hoagland and Arnon 50% (PC+HS 50%, T7= coconut powder + solution of Hoagland and Arnon 75% (PC+HS 75%, T8= coconut powder + solution of Hoagland and Arnon 100% (100% PC+HS, T9= coconut powder + Aminoagro Mol (PC+AM, T10= coconut powder Aminoagro Root (PC+AR. The solutions were applied eight times, 10 mL on each application, since the fourth day after sowing date (DAS, when the evaluation of seedlings emergence began. At 24 DAS we evaluated the fresh weight of shoots and roots, root length, number of roots in the upper third and contents of macro and micronutrients in the aboveground part. The cv. Top Gun presented higher levels of nutrients, except for iron and copper. The treatments T6, T7 and T8 presented levels of nutrients in plants similar to the commercial substrate Plantmax. In general, the combinations of coconut dust associated with the nutrient solution of Hoagland and Arnon at 50, 75 and 100% and Aminoagro Root proved to be

Piriformospora indica root colonization triggers local and systemic root responses and inhibits secondary colonization of distal roots.

Science.gov (United States)

Pedrotti, Lorenzo; Mueller, Martin J; Waller, Frank

2013-01-01

Piriformosporaindica is a basidiomycete fungus colonizing roots of a wide range of higher plants, including crop plants and the model plant Arabidopsis thaliana. Previous studies have shown that P. indica improves growth, and enhances systemic pathogen resistance in leaves of host plants. To investigate systemic effects within the root system, we established a hydroponic split-root cultivation system for Arabidopsis. Using quantitative real-time PCR, we show that initial P. indica colonization triggers a local, transient response of several defense-related transcripts, of which some were also induced in shoots and in distal, non-colonized roots of the same plant. Systemic effects on distal roots included the inhibition of secondary P. indica colonization. Faster and stronger induction of defense-related transcripts during secondary inoculation revealed that a P. indica pretreatment triggers root-wide priming of defense responses, which could cause the observed reduction of secondary colonization levels. Secondary P. indica colonization also induced defense responses in distant, already colonized parts of the root. Endophytic fungi therefore trigger a spatially specific response in directly colonized and in systemic root tissues of host plants.

Root canal treatment of bilateral three-rooted maxillary first premolars

Directory of Open Access Journals (Sweden)

Bhavana Gandhi

2012-01-01

Full Text Available In endodontics, several anatomic variations occur in teeth, both externally and in the internal root morphology, which play a very significant role in the diagnosis and treatment outcome. A thorough knowledge of the root canal anatomy, careful interpretation of the angled radiographs, proper endodontic access cavity preparation, and exploration of the root canal are the prerequisites for endodontic success. In a maxillary first premolar, it is rare to find extra roots and canals, and the aim of the present article is to report a case about the successful diagnosis and clinical management of bilateral three-rooted maxillary first premolars, with three independent root canals.

Dry and coating of powders

International Nuclear Information System (INIS)

Alonso, M.; Alguacil, F. J.

1999-01-01

This paper presents a review on the mixing and coating of powders by dry processes. The reviews surveys fundamental works on mixture characterization (mixing index definitions and sampling techniques), mixing mechanisms and models, segregation with especial emphasis on free-surface segregation, mixing of cohesive powders and interparticle forces, ordered mixing (dry coating) including mechanism, model and applications and mixing equipment selection. (Author) 180 refs

Factors affecting the electrostatic charge of ceramic powders

International Nuclear Information System (INIS)

Lorite, I.; Romero, J.; Fernandez, J. F.

2011-01-01

The phenomenon of electrostatic charge in ceramic powders takes place when the particle surfaces enter in contact between them or with the containers. The accumulation of electrostatic charge is of relevance in ceramic powders in view of their insulating character and the risk of explosions during the material handling. In this work the main factors that affect the appearance of intrinsic charge and tribo-charge in ceramic powder have been studied. In ceramic powders of alumina it has been verified that the smallest particle sizes present an increase of the electrostatic charge of negative polarity. A correlation has been observed between the nature of the OH -surface groups and the electrostatic charge. The intrinsic charge and the tribocharge in ceramic powders can be diminished by compensating the surface groups that support the charge. The dry dispersion of nanoparticles on microparticles allows surface charge compensation with a noticeable modification of the powder agglomeration. (Author) 19 refs.

Biodegradation of thermoplastic starch/eggshell powder composites.

Science.gov (United States)

Bootklad, Munlika; Kaewtatip, Kaewta

2013-09-12

Thermoplastic starch (TPS) was prepared using compression molding and chicken eggshell was used as a filler. The effect of the eggshell powder (EP) on the properties of TPS was compared with the effect of commercial calcium carbonate (CC). The organic compound on the surface of the eggshell powder acted as a coupling agent that resulted in a strong adhesion between the eggshell powder and the TPS matrix, as confirmed by SEM micrographs. The biodegradation was determined by the soil burial test. The TPS/EP composites were more rapidly degraded than the TPS/CC composites. In addition, the eggshell powder improved the water resistance and thermal stability of the TPS. Copyright © 2013 Elsevier Ltd. All rights reserved.

Role of forgings in powder metallurgy industry

International Nuclear Information System (INIS)

Hayes, A.F.; DeRidder, A.J.

1975-01-01

Forging of powder metallurgy materials is discussed. Information and data are included on forging powder metallurgy W, Mo, In 100, Rene 95, Astroloy, Be, and Ti. It is noted that the combination of powder metallurgy and forging work provides the best product from standpoints of reproducibility, freedom from segregation, low scrap rate, and uniform mechanical properties. Experience is being used to develop contour forging from hot isostatic pressed billets or preforms. The quality of this product is under evaluation. Results show steady improvement and it is anticipated that continued effort will soon produce a reliable, less costly product. Forging can continue to be relied upon to correct subtle defects present in powder metallurgy material

Surface chemistry and microscopy of food powders

Science.gov (United States)

Burgain, Jennifer; Petit, Jeremy; Scher, Joël; Rasch, Ron; Bhandari, Bhesh; Gaiani, Claire

2017-12-01

Despite high industrial and scientific interest, a comprehensive review of the surface science of food powders is still lacking. There is a real gap between scientific concerns of the field and accessible reviews on the subject. The global description of the surface of food powders by multi-scale microscopy approaches seems to be essential in order to investigate their complexity and take advantage of their high innovation potential. Links between these techniques and the interest to develop a multi-analytical approach to investigate scientific questions dealing with powder functionality are discussed in the second part of the review. Finally, some techniques used in others fields and showing promising possibilities in the food powder domain will be highlighted.

Root canal treatment of a maxillary first premolar with three roots

OpenAIRE

Mathew, Josey; Devadathan, Aravindan; Syriac, Gibi; Shamini, Sai

2015-01-01

Successful root canal treatment needs a thorough knowledge of both internal and external anatomy of a tooth. Variations in root canal anatomy constitute an impressive challenge to the successful completion of endodontic treatment. Undetected extra roots and canals are a major reason for failed root canal treatment. Three separate roots in a maxillary first premolar have a very low incidence of 0.5?6%. Three rooted premolars are anatomically similar to molars and are sometimes called ?small mo...

A breath actuated dry powder inhaler

NARCIS (Netherlands)

de Boer, Anne; Frijlink, Henderik W.; Hagedoorn, Paul

2015-01-01

A breath actuated dry powder inhaler with a single air circulation chamber for de-agglomeration of entrained powdered medicament using the energy of the inspiratory air stream. The chamber has a substantially polygonal sidewall, a plurality of air supply channels entering the chamber substantially

Efficient method of protein extraction from Theobroma cacao L. roots for two-dimensional gel electrophoresis and mass spectrometry analyses.

Science.gov (United States)

Bertolde, F Z; Almeida, A-A F; Silva, F A C; Oliveira, T M; Pirovani, C P

2014-07-04

Theobroma cacao is a woody and recalcitrant plant with a very high level of interfering compounds. Standard protocols for protein extraction were proposed for various types of samples, but the presence of interfering compounds in many samples prevented the isolation of proteins suitable for two-dimensional gel electrophoresis (2-DE). An efficient method to extract root proteins for 2-DE was established to overcome these problems. The main features of this protocol are: i) precipitation with trichloroacetic acid/acetone overnight to prepare the acetone dry powder (ADP), ii) several additional steps of sonication in the ADP preparation and extractions with dense sodium dodecyl sulfate and phenol, and iii) adding two stages of phenol extractions. Proteins were extracted from roots using this new protocol (Method B) and a protocol described in the literature for T. cacao leaves and meristems (Method A). Using these methods, we obtained a protein yield of about 0.7 and 2.5 mg per 1.0 g lyophilized root, and a total of 60 and 400 spots could be separated, respectively. Through Method B, it was possible to isolate high-quality protein and a high yield of roots from T. cacao for high-quality 2-DE gels. To demonstrate the quality of the extracted proteins from roots of T. cacao using Method B, several protein spots were cut from the 2-DE gels, analyzed by tandem mass spectrometry, and identified. Method B was further tested on Citrus roots, with a protein yield of about 2.7 mg per 1.0 g lyophilized root and 800 detected spots.

Surface quality analysis of die steels in powder-mixed electrical discharge machining using titan powder in fine machining

Directory of Open Access Journals (Sweden)

Banh Tien Long

2016-06-01

Full Text Available Improving the quality of surface molds after electrical discharge machining is still being considered by many researchers. Powder-mixed dielectric in electrical discharge machining showed that it is one of the processing methods with high efficiency. This article reports on the results of surface quality of mold steels after powder-mixed electrical discharge machining using titanium powder in fine machining. The process parameters such as electrode material, workpiece material, electrode polarity, pulse on-time, pulse off-time, current, and titanium powder concentration were considered in the research. These materials are most commonly used with die-sinking electrical discharge machining in the manufacture of molds and has been selected as the subject of research: workpiece materials were SKD61, SKT4, and SKD11 mold steels, and electrode materials were copper and graphite. Taguchi’s method is used to design experiments. The influence of the parameters on surface roughness was evaluated through the average value and ratio (S/N. Results showed that the parameters such as electrical current, electrode material, pulse on-time, electrode polarity, and interaction between the electrode materials with concentration powder mostly influence surface roughness and surface roughness at optimal parameters SRopt = 1.73 ± 0.39 µm. Analysis of the surface layer after powder-mixed electrical discharge machining using titanium powder in optimal conditions has shown that the white layer with more uniform thickness and increased hardness (≈861.0 HV, and amount and size of microscopic cracks, is reduced. This significantly leads to the increase in the quality of the surface layer.

Medico-legal aspects of vertical root fractures in root filled teeth

DEFF Research Database (Denmark)

Rosen, E; Tsesis, I; Tamse, A

2012-01-01

To analyse the medico-legal aspects of vertical root fracture (VRF) following root canal treatment (RCT).......To analyse the medico-legal aspects of vertical root fracture (VRF) following root canal treatment (RCT)....

Optimization of Premix Powders for Tableting Use.

Science.gov (United States)

Todo, Hiroaki; Sato, Kazuki; Takayama, Kozo; Sugibayashi, Kenji

2018-05-08

Direct compression is a popular choice as it provides the simplest way to prepare the tablet. It can be easily adopted when the active pharmaceutical ingredient (API) is unstable in water or to thermal drying. An optimal formulation of preliminary mixed powders (premix powders) is beneficial if prepared in advance for tableting use. The aim of this study was to find the optimal formulation of the premix powders composed of lactose (LAC), cornstarch (CS), and microcrystalline cellulose (MCC) by using statistical techniques. Based on the "Quality by Design" concept, a (3,3)-simplex lattice design consisting of three components, LAC, CS, and MCC was employed to prepare the model premix powders. Response surface method incorporating a thin-plate spline interpolation (RSM-S) was applied for estimation of the optimum premix powders for tableting use. The effect of tablet shape identified by the surface curvature on the optimization was investigated. The optimum premix powder was effective when the premix was applied to a small quantity of API, although the function of premix was limited in the case of the formulation of large amount of API. Statistical techniques are valuable to exploit new functions of well-known materials such as LAC, CS, and MCC.

Production and properties of boride powders

International Nuclear Information System (INIS)

Klinskaya, N.A.; Koroleva, E.B.; Petrunichev, V.A.

1990-01-01

Results of plasma metallization of boride powders 40-80 μ diam. are presented. Peculiarities of changes of granulometric powder composition and of metallic cover on refractory cores were investigated. There are shown size- and compositional cores effects on metallization level of poders and on cover structure

Quality of clay-powders of industrial assortment

Energy Technology Data Exchange (ETDEWEB)

Lityayeva, Z A; Dzetl, B G; Goncharenko, N N; Naurova, I V; Rybchenko, V I; Voyevodin, L I

1979-01-01

Nomenclature was developed for the quality indicators of clay powders which took into consideration the foreign experience, and it is suggested that a suspension of clay powders be viewed as the simplest type of drilling. In this case the technique of preparing the suspensions approaches the maximum to that used in the recommended standard (TU-39-043-074). The output of solution is determined with standardized effective viscosity /eta/ ef =/sup 20/ /SUP cP/ on a series domestic rotary viscosimeter VSN-3 with gradient of shear velocity EPSILON=666 sec/sup -1/; with EPSILON=1022 sec /sup -1//eta/ /SUB ef/ = 15 cP. This makes it possible to obtain data comparable to the foreign standards regarding the output of the fluid from the powders. According to the suggested technique, the clay powder is dispersed for 20-30 minutes in water or saturated solution of NaC1 in a mixing unit ''Voronezh2'' with rotation frequency of 9000 rpm, is left to rest and is again dispersed for 15 minutes. Then the dynamic shear stress (P /SUB k2/ ), plastic viscosity (/eta/ /SUB ef/ ), coefficients of coagulation (K /SUB c/ ) and thyxotropic (K /SUB T/ ) structure-formation are defined. Measurements are made on the instrument FLR-1 of water output with 0.7 (B) or 0.1 (B) MPa. According to this technique, a comparison was made of the domestic powders of industrial assortment with the powder ''Aquagel'' widely used abroad. It was established that only the modified concrete powders with correct selection of reagents can compete with the foreign.

3D Model Studies on the Effect of Bed and Powder Type Upon Radial Static Pressure and Powder Distribution in Metallurgical Shaft Furnaces

Directory of Open Access Journals (Sweden)

Panic B.

2017-09-01

Full Text Available The flow of gases in metallurgical shaft furnaces has a decisive influence on the course and process efficiency. Radial changes in porosity of the bed cause uneven flow of gas along the radius of the reactor, which sometimes is deliberate and intentional. However, holdup of solid particles in descending packed beds of metallurgical shaft furnaces can lead to unintentional changes in porosity of the bed along the radial reactor. Unintentional changes in porosity often disrupt the flow of gas causing poor performance of the furnace. Such disruptions of flow may occur in the blast furnace due to high level of powder content in gas caused by large amount of coal dust/powder insufflated as fuel substitute. The paper describes the model test results of radial distribution of static pressure and powder hold up within metallurgical reactor. The measurements were carried out with the use of 3D physical model of two-phase flow gas-powder in the moving (descending packed bed. Sinter or blast furnace pellets were used as packed bed while carbon powder or iron powder were used as the powder. Wide diversity within both static pressure distribution and powder distribution along the radius of the reactor were observed once the change in the type of powder occurred.

Advances in food powder agglomeration engineering.

Science.gov (United States)

Cuq, B; Gaiani, C; Turchiuli, C; Galet, L; Scher, J; Jeantet, R; Mandato, S; Petit, J; Murrieta-Pazos, I; Barkouti, A; Schuck, P; Rondet, E; Delalonde, M; Dumoulin, E; Delaplace, G; Ruiz, T

2013-01-01

Food powders are used in everyday life in many ways and offer technological solutions to the problem of food production. The natural origin of food powders, diversity in their chemical composition, variability of the raw materials, heterogeneity of the native structures, and physicochemical reactivity under hydrothermal stresses contribute to the complexity in their behavior. Food powder agglomeration has recently been considered according to a multiscale approach, which is followed in the chapter layout: (i) at the particle scale, by a presentation of particle properties and surface reactivity in connection with the agglomeration mechanisms, (ii) at the mechanisms scale, by describing the structuration dynamics of agglomerates, (iii) at the process scale, by a presentation of agglomeration technologies and sensors and by studying the stress transmission mode in the powder bed, and finally (iv) by an integration of the acquired knowledge, thanks to a dimensional analysis carried out at each scale. Copyright © 2013 Elsevier Inc. All rights reserved.

Properties and sinterability of wet and dry attrition-milled OREOXed powder

International Nuclear Information System (INIS)

Lee, J. W.; Kim, J. H.; Kim, W. K.; Park, K. I.; Lee, J. W.

2001-01-01

The powder properties and sinterability were investigated with the powder prepared by wet and dry attrition milling of OREOX-treated powder. The OREOX-treated powder was prepared from the simulated spent fuel. Powder having less than 1 μm of average particle size could be obtained by dry milling, but not be obtained by wet milling. Thus, specific surface area of dry milled powder was higher than that of wet milled powder. With increasing of milling time, dry milled powder formed dense agglomerate while wet milled powder showed loose agglomerate. The pellets with higher than 95% T.D. of sintered density and larger than 7 μm of grain size were made with the milled powder regardless of milling method. The milling time in wet milling has greatly improved the sinterability. The pellets produced with dry milled powder have higher sintered density and larger grain size

Light and decapitation effects on in vitro rooting in maize root segments.

Science.gov (United States)

Golaz, F W; Pilet, P E

1985-10-01

The effects of white light and decapitation on the initiation and subsequent emergence and elongation of lateral roots of apical maize (Zea mays L. cv LG 11) root segments have been examined. The formation of lateral root primordium was inhibited by the white light. This inhibition did not depend upon the presence of the primary root tip. However, root decapitation induced a shift of the site of appearance of the most apical primordium towards the root apex, and a strong disturbance of the distribution pattern of primordium volumes along the root axis. White light had a significant effect neither on the distribution pattern of primordium volumes, nor on the period of primordium development (time interval required for the smallest detectable primordia to grow out as secondary roots). Thus, considering the rooting initiation and emergence, the light effect was restricted to the initiation phase only. Moreover, white light reduced lateral root elongation as well as primary root growth.

Dielectric properties of tantalum powder with broccoli-like morphology

Energy Technology Data Exchange (ETDEWEB)

Baba, Masahiko [Department of Energy Science and Technology, Kyoto University, Yoshida-Honmachi, Sakyo-ku, Kyoto 606-8501 (Japan); Suzuki, Ryosuke O [Department of Energy Science and Technology, Kyoto University, Yoshida-Honmachi, Sakyo-ku, Kyoto 606-8501 (Japan)

2005-04-19

Metallic tantalum powder with broccoli-like morphology, consisting of spherical fine particles and of long rods or thin plates, was prepared in a hundred gram scale by calcium reduction of Ta{sub 2}O{sub 5} in molten CaCl{sub 2}. The properties as electrolytic capacitor were evaluated in comparison with commercial powder obtained by Na reduction and with powder consisting of only fine particles obtained by Ca reduction. The capacitance was larger than that of conventional powder with the same surface area, because the broccoli-like powder showed a strong resistance against shrinkage during high temperature annealing due to the framework of branches. The powder with new broccoli-like morphology can circumvent the conventional treatments for grain size control and gas removal.

Dielectric properties of tantalum powder with broccoli-like morphology

International Nuclear Information System (INIS)

Baba, Masahiko; Suzuki, Ryosuke O.

2005-01-01

Metallic tantalum powder with broccoli-like morphology, consisting of spherical fine particles and of long rods or thin plates, was prepared in a hundred gram scale by calcium reduction of Ta 2 O 5 in molten CaCl 2 . The properties as electrolytic capacitor were evaluated in comparison with commercial powder obtained by Na reduction and with powder consisting of only fine particles obtained by Ca reduction. The capacitance was larger than that of conventional powder with the same surface area, because the broccoli-like powder showed a strong resistance against shrinkage during high temperature annealing due to the framework of branches. The powder with new broccoli-like morphology can circumvent the conventional treatments for grain size control and gas removal

Development and directions of powder diffraction on proteins

Energy Technology Data Exchange (ETDEWEB)

Von Dreele, R B; Besnard, C; Basso, S; Camus, F; Pattison, P; Schiltz, M; Wright, J P; Margiolaki, R; Fitch, A N; Fox, G C; Prugoveeki, S; Beckers, D; Helliwell, J R; Helliwell, M; Jones, R H; Roberts, M A; Miura, K; Kahn, R; Giacovazzo, C; Altomare, A; Caliandro, R; Camalli, M; Cuocci, C; Moliterni, A G.G.; Rizzi, R; Hinrichsen, B; Kern, A; Coelho, A A; Degen, T; Kokkinidis, M; Fadouloglou, V; Gazi, A; Panopoulos, N; Pinotsis, N; Wilmanns, M; Norrman, M; Schluckebier, G; Prugoveeki, B; Dilovic, J; Matkovic-Calogovic, D; Bill, David; Markvardsen, A; Grosse-Kunstleve, R; Rius, J; Glykos Nicholas, M; Murshudov, G N

2007-07-01

X-ray diffraction is one of the most important method for obtaining information about the structure of proteins and thereby for gaining insight into fundamental biological and biochemical mechanisms. This seminar was dedicated to X-ray powder diffraction and was organized around 6 sessions: 1) what can powder diffraction do for proteins?, 2) adapting experimentally to proteins, 3) interpreting powder data, 4) the world of protein crystallography, 5) advancing methods for powder data analysis, and 6) transferable methods from single crystals. This document gathers the abstracts of the 23 papers presented. (A.C.)

Development and directions of powder diffraction on proteins

International Nuclear Information System (INIS)

Von Dreele, R.B.; Besnard, C.; Basso, S.; Camus, F.; Pattison, P.; Schiltz, M.; Wright, J.P.; Margiolaki, R.; Fitch, A.N.; Fox, G.C.; Prugoveeki, S.; Beckers, D.; Helliwell, J.R.; Helliwell, M.; Jones, R.H.; Roberts, M.A.; Miura, K.; Kahn, R.; Giacovazzo, C.; Altomare, A.; Caliandro, R.; Camalli, M.; Cuocci, C.; Moliterni, A.G.G.; Rizzi, R.; Hinrichsen, B.; Kern, A.; Coelho, A.A.; Degen, T.; Kokkinidis, M.; Fadouloglou, V.; Gazi, A.; Panopoulos, N.; Pinotsis, N.; Wilmanns, M.; Norrman, M.; Schluckebier, G.; Prugoveeki, B.; Dilovic, J.; Matkovic-Calogovic, D.; Bill, David; Markvardsen, A.; Grosse-Kunstleve, R.; Rius, J.; Glykos Nicholas, M.; Murshudov, G.N.

2007-01-01

X-ray diffraction is one of the most important method for obtaining information about the structure of proteins and thereby for gaining insight into fundamental biological and biochemical mechanisms. This seminar was dedicated to X-ray powder diffraction and was organized around 6 sessions: 1) what can powder diffraction do for proteins?, 2) adapting experimentally to proteins, 3) interpreting powder data, 4) the world of protein crystallography, 5) advancing methods for powder data analysis, and 6) transferable methods from single crystals. This document gathers the abstracts of the 23 papers presented. (A.C.)

Powder injection molding of Stellite 6 powder: Sintering, microstructural and mechanical properties

International Nuclear Information System (INIS)

Gülsoy, H. Özkan; Özgün, Özgür; Bilketay, Sezer

2016-01-01

The purpose of this study was to produce Co-based Stellite 6 superalloy components by using the method of Powder Injection Molding (PIM) and to characterize the microstructural and mechanical properties of the produced components. The experimental studies were started through the formation of feedstock by mixing Stellite 6 powder with a multicomponent binder system. Prepared feedstock was formed by utilizing powder injection molding technique. Then the molded samples were subjected to the solvent and thermal debinding processes. Different sintering cycles were applied to the raw components for the purpose of determining the optimum sintering conditions. The densities of the sintered components were determined in accordance with the Archimedes' principle. The microstructural characterization was performed through scanning electron microscope (SEM) analysis, energy dispersive spectrometry (EDS) analyses, and X-ray diffraction (XRD) analysis. Hardness measurement and tensile test were conducted in order to determine the mechanical properties. The results illustrated that the injection molded Stellite 6 components were composed of fine and equiaxed grains, plenty of carbide precipitates exhibiting homogenous distribution throughout the microstructure formed at the grain boundaries and thus the mechanical properties were considerably high.

Some characteristics of urea-formaldehyde powder adhesives

Directory of Open Access Journals (Sweden)

Miljković Jovan

2006-01-01

Full Text Available Urea-formaldehyde (UF glue resins were the most important type of adhesives in the wood industry last 60 years, especially for the production of wood based panels. More convenient spray dried UF powders went into use last two decades. Small and medium private wood processing plants in Serbia prefer to use such powder adhesives, since they are more convenient for small capacity production. There is no production of UF powder resin in Serbia so necessary quantities are imported from abroad including producers from Asia. However, their characteristics are variable, dependent on syntheses steps and not well known among users. Objective of this research was to determine conveniences and lacks in application of two imported UF powder resins in comparison to domestic UF emulsion.

Nanostructured hydroxyapatite powders produced by a flame-based technique

Energy Technology Data Exchange (ETDEWEB)

Trommer, R.M., E-mail: rafael_trommer@yahoo.com.br [Ceramic Materials Laboratory, av. Osvaldo Aranha 99/705, 90035190, Porto Alegre, RS (Brazil); Santos, L.A. [Biomaterials Laboratory, av. Bento Goncalves 9500, Campus do Vale Setor IV Predio 74 Sala 123, 91501970, Porto Alegre, RS (Brazil); Bergmann, C.P. [Ceramic Materials Laboratory, av. Osvaldo Aranha 99/705, 90035190, Porto Alegre, RS (Brazil)

2009-08-01

In this work we reported the production of hydroxyapatite (HA) powder, one of the most studied calcium phosphates in the bioceramics field, using a cost-effective apparatus, composed by three major components: the atomization device, the pilot and main flames and finally the powder collector system. Calcium acetate and ammonium phosphate, diluted in ethanol and water, were used as salts in the precursor solution. The Ca/P molar ratio in the precursor solution was 1.65, equivalent to biological hydroxyapatite. After its production and collection, HA powder was calcined at 600 deg. C for 2 h. X-ray diffraction analysis pointed to the formation of crystalline hydroxyapatite powders. Carbonate was identified in the powders by Fourier-transform infrared (FTIR) spectroscopy. Scanning electronic microscopy (SEM) showed that the powders were composed of spherical primary particles and secondary aggregates, with the morphology unchanged after calcination. By transmission electronic microscopy (TEM), it was observed that the crystallite size of the primary particles was 24.8 {+-} 5.8 nm, for the calcined powder. The specific surface area was 15.03 {+-} 6.4 and 26.50 {+-} 7.6 m{sup 2}/g, for the as-synthetized and calcined powder respectively.

[Study of relationship between powder-size gradation and mechanical properties of Zirconia toughened glass infiltrated nanometer-ceramic composite powder].

Science.gov (United States)

Chai, Feng; Xu, Ling; Liao, Yun-mao; Chao, Yong-lie

2003-07-01

The fabrication of all-ceramic dental restorations is challenged by ceramics' relatively low flexural strength and intrinsic poor resistance to fracture. This paper aimed at investigating the relationships between powder-size gradation and mechanical properties of Zirconia toughened glass infiltrated nanometer-ceramic composite (Al(2)O(3)-nZrO(2)). Al(2)O(3)-nZrO(2) ceramics powder (W) was processed by combination methods of chemical co-precipitation and ball milling with addition of different powder-sized ZrO(2). Field-emission scanning electron microscopy was used to determine the particle size distribution and characterize the particle morphology of powders. The matrix compacts were made by slip-casting technique and sintered to 1,450 degrees C and flexural strength and the fracture toughness of them were measured. 1. The particle distribution of Al(2)O(3)-nZrO(2) ceramics powder ranges from 0.02 - 3.5 micro m and among them the superfine particles almost accounted for 20%. 2. The ceramic matrix samples with addition of nZrO(2) (W) showed much higher flexural strength (115.434 +/- 5.319) MPa and fracture toughness (2.04 +/- 0.10) MPa m(1/2) than those of pure Al(2)O(3) ceramics (62.763 +/- 7.220 MPa; 1.16 +/- 0.02 MPa m(1/2)). The particle size of additive ZrO(2) may impose influences on mechanical properties of Al(2)O(3)-nZrO(2) ceramics matrix. Good homogeneity and reasonable powder-size gradation of ceramic powder can improve the mechanical properties of material.

On suitability of novel fluidised bed technique for separation of metallic powders during commercial powder metallurgical processing

NARCIS (Netherlands)

Ritherdon, J; Dechsiri, C; Jones, AR; Hoffmann, AC; Wright, IG

Experiments have been performed to test the efficiency with which a novel fluidised bed technique could separate different metallic powders in terms of size and density. The overall aim was to assess the potential of this technique for the commercial separation of defective powder fractions from

Study on Quality Aggregate Construction Powder

International Nuclear Information System (INIS)

Myat Ko; Kyaw Naing; Thazin Lwin; Khin Mar Tun

2008-03-01

This research work deals with a view to promote cement replacement materials i-e aggregate construction powder, also known as building powder or construction powder . It has been used as lime substituent in construction work in Myanmar since 1990's. It is mixed with other construction materials such as cement, sand, etc. and used in plastering, tiling, arranging bricks and smoothing the face of the buildings.This work also deals with some aspects in physical properties of four different aggregate construction powder samples such as Moe Hein, Man Thiri, Shwe Taung and Kyauk Sue. In addition, these four different samples were characterized by using spectroscopic methods such as ED-XRF, AAS, FT-IR and XRD. In support of the finding by the analytical assays of Moe Hein aggregate construction powder, it indicated the percent composition of the presence of SiO2 12.13%, Al2O3 7.40%, Fe2O3 0.94%, CaO 41.00%,MgO 1.50% total sulphur 1.15%, chloride 1.49%, carbonate 43.63% and sulphate 3.44%. The analytical assays of Sin Min cement, Kyant cement, brick powder and pozzolan were also carried out in this research work. The mixing between various ratios of Moe Hein and Kyant cement as well as Sin Min II cement were done and their mechanical strengths such as setting time, tensile strength and compressive strength of each sample were studied. The quality of mixing ratio 50:50 of Moe Hein and Kyant cement was found to be comparable to the ASTM standard type II Protland cement which is for general use.

Strength Improvement of Clay Soil by Using Stone Powder

Directory of Open Access Journals (Sweden)

Ahmed Sameer Abdulrasool

2015-05-01

Full Text Available Soil stabilization with stone powder is a good solution for the construction of subgrade for road way and railway lines, especially under the platforms and mostly in transition zones between embankments and rigid structures, where the mechanical properties of supporting soils are very influential. Stone powder often has a unique composition which justifies the need for research to study the feasibility of using this stone powder type for ground improvement applications. This paper presents results from a comprehensive laboratory study carried out to investigate the feasibility of using stone powder for improvement of engineering properties of clays. The stone powder contains bassanite (CaSO4. ½ H2O, and Calcite (CaCO3. Three percentages are used for stone powder (1%, 3% and 5% by dry weight of clay. Several tests are made to investigate the soil behavior after adding the stone powder (Atterberg limits, Standard Proctor density, Grain size distribution, Specific gravity, Unconfined Compressive test, and California bearing ratio test. Unconfined Compressive tests conducted at different curing. The samples are tested under both soaked and unsoaked condition. Chemical tests and X-ray diffraction analyses are also carried out. Stone powder reacts with clay producing decreasing in plasticity and The curves of grain size distribution are shifted to the coarse side as the stone powder percentage increase; the soil becomes more granular, and also with higher strength.

Production of rare earth polishing powders in Russia

International Nuclear Information System (INIS)

Kosynkin, V.D.; Ivanov, E.N.; Kotrekhov, V.A.; Shtutza, M.G.; Grabko, A.I.

1998-01-01

Full text: Russia is a potent producer of polishing powders made of rare earth material presented as an extensive and well developed base. Considering the reserves, the facilities predisposition and the polishing agent (cerium dioxide) content the chief mineral source is loparite, apatite and monazite. The production of rare earth polishing powders is based on specially developed continuous technological processes, corrosion-proof equipment, ensuring a high and stable production quality. A special attention is paid to the radiation safety of the powders. The initial material for the rare earth polishing powders based on loparite is the fusion cake of rare earth chlorides obtained at that mineral chlorination. The technology of the polishing powder production from the REE fusion cake includes the following stages: dissolution of the REE fusion cake chlorides; - thorough cleaning of the REE fusion cake chlorides from radioactive and non-rare-earth impurities; chemical precipitation of REE carbonates, obtaining middlings with proper material and granulometric composition, thermal treatment of precipitated carbonates followed with the operations of drying and roasting; classification of roasted oxides, obtaining end products - polishing powders. The production of fluorine-containing powders includes the stage of their fluorination after the stage of carbonate precipitation. The stabilizing doping can be introduced both into the middlings during one of the technological process of powders manufacturing and into the end product. Rare earth polishing powders are manufactured in Russia by the Share Holding Company 'Chepetz Mechanical Plant' (ChMP Co.), the city of Glasov. The plant produces a number of polishing materials, such as; polishing powder Optinol, containing at least 50% by mass of cerium dioxide, used in the mass production of optical and other articles; polishing powder Optinol-10 with doping to improve the sedimentary and aggregate stability of the solid phase

Root canal irrigants

OpenAIRE

Kandaswamy, Deivanayagam; Venkateshbabu, Nagendrababu

2010-01-01

Successful root canal therapy relies on the combination of proper instrumentation, irrigation, and obturation of the root canal. Of these three essential steps of root canal therapy, irrigation of the root canal is the most important determinant in the healing of the periapical tissues. The primary endodontic treatment goal must thus be to optimize root canal disinfection and to prevent reinfection. In this review of the literature, various irrigants and the interactions between irrigants are...

Roller compaction: Effect of relative humidity of lactose powder.

Science.gov (United States)

Omar, Chalak S; Dhenge, Ranjit M; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

2016-09-01

The effect of storage at different relative humidity conditions, for various types of lactose, on roller compaction behaviour was investigated. Three types of lactose were used in this study: anhydrous lactose (SuperTab21AN), spray dried lactose (SuperTab11SD) and α-lactose monohydrate 200M. These powders differ in their amorphous contents, due to different manufacturing processes. The powders were stored in a climatic chamber at different relative humidity values ranging from 10% to 80% RH. It was found that the roller compaction behaviour and ribbon properties were different for powders conditioned to different relative humidities. The amount of fines produced, which is undesirable in roller compaction, was found to be different at different relative humidity. The minimum amount of fines produced was found to be for powders conditioned at 20-40% RH. The maximum amount of fines was produced for powders conditioned at 80% RH. This was attributed to the decrease in powder flowability, as indicated by the flow function coefficient ffc and the angle of repose. Particle Image Velocimetry (PIV) was also applied to determine the velocity of primary particles during ribbon production, and it was found that the velocity of the powder during the roller compaction decreased with powders stored at high RH. This resulted in less powder being present in the compaction zone at the edges of the rollers, which resulted in ribbons with a smaller overall width. The relative humidity for the storage of powders has shown to have minimal effect on the ribbon tensile strength at low RH conditions (10-20%). The lowest tensile strength of ribbons produced from lactose 200M and SD was for powders conditioned at 80% RH, whereas, ribbons produced from lactose 21AN at the same condition of 80% RH showed the highest tensile strength. The storage RH range 20-40% was found to be an optimum condition for roll compacting three lactose powders, as it resulted in a minimum amount of fines in the

21 CFR 176.350 - Tamarind seed kernel powder.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Tamarind seed kernel powder. 176.350 Section 176... Substances for Use Only as Components of Paper and Paperboard § 176.350 Tamarind seed kernel powder. Tamarind seed kernel powder may be safely used as a component of articles intended for use in producing...

Preparation of potassium-reduced tantalum powders

International Nuclear Information System (INIS)

Kolosov, V.N.; Miroshnichenko, M.N.; Orlov, V.M.; Prokhorova, T.Yu.

2005-01-01

Characteristics of tantalum powders prepared by reduction of molten potassium heptafluorotantalate with liquid potassium are studied in a temperature range of 750 - 850 deg C using potassium chloride as a flux at a ratio of K 2 TaF 7 : KCl = 1, 2, and 3. The use of potassium as a reducing agent facilitates washing of tantalum powders for impurity salt removal, reduces sodium content and leakage currents in the anodes. As compared to sodium process, the potassium reduction results in a high yield of sponge material, a decrease in the specific surface area and yield of tantalum powder suitable for manufacture of capacitor anodes [ru

Determination of the functional properties of Kappaphycus alvarezii seaweed powder

International Nuclear Information System (INIS)

Sjamsiah; Nazaruddin Ramli; Rusli Daik; Mohd Ambar Yarmo

2013-01-01

Seaweed Kappaphycus alvarezii powder prepared by spray drying (SD), freeze drying (FD) and sun drying(SND) were determined their functional properties such as swelling capacity (SWC), water holding capacity (WHC), oil holding capacity (OHC), viscosity and gel strength. The study showed that the Kappaphycus alvarezii seaweed powder obtained by FD and SND have the ability to swell to 25 mL/ g and 50 mL/ g respectively, while the SD powder formed a homogeneous solution and it exhibited highly viscous solution (SWC 100 mL/ g). The WHC of SND powder (30.67 g/ g) was higher (p<0.05) than the FD (21.33 g/ g) and SD (4.67 g/ g) powders. The OHC of FD powder (19.81 g/ g) was higher (p<0.05) than the SD (5.11 g/ g) and SND (4.67 g/ g) powders. While the viscosity of the FD, SND and SD powders were 0.22, 0.17 and 0.06 Pa.s respectively. Meanwhile, the gel strength of the SD powder (82.77 gf) was higher (p<0.05) than the FD (57.1 gf) and SND (35.01 gf) powders. These results on determination of functional properties shows that the SD powder had the most potential to be applied as a viscosity modifier in the manufacturing of beverages.(author)

Effects of Powder Attributes and Laser Powder Bed Fusion (L-PBF) Process Conditions on the Densification and Mechanical Properties of 17-4 PH Stainless Steel

Science.gov (United States)

Irrinki, Harish; Dexter, Michael; Barmore, Brenton; Enneti, Ravi; Pasebani, Somayeh; Badwe, Sunil; Stitzel, Jason; Malhotra, Rajiv; Atre, Sundar V.

2016-03-01

The effects of powders attributes (shape and size distribution) and critical processing conditions (energy density) on the densification and mechanical properties of laser powder bed fusion (L-PBF) 17-4 PH stainless steel were studied using four types of powders. The % theoretical density, ultimate tensile strength and hardness of both water- and gas-atomized powders increased with increased energy density. Gas-atomized powders showed superior densification and mechanical properties when processed at low energy densities. However, the % theoretical density and mechanical properties of water-atomized powders were comparable to gas-atomized powders when sintered at a high energy density of 104 J/mm3. An important result of this study was that, even at high % theoretical density (97% ± 1%), the properties of as-printed parts could vary over a relatively large range (UTS: 500-1100 MPa; hardness: 25-39 HRC; elongation: 10-25%) depending on powder characteristics and process conditions. The results also demonstrate the feasibility of using relatively inexpensive water-atomized powders as starting raw material instead of the typically used gas-atomized powders to fabricate parts using L-PBF techniques by sintering at high energy densities.

Preparation of cerium oxide for lens polishing powder

International Nuclear Information System (INIS)

Injarean, Uthaiwan; Rodthongkom, Chouvana; Pichestapong, Pipat; Changkrurng, Kalaya

2003-10-01

Cerium is an element of rare earth group which is called lanthanide series. It is found in the ores like monazite and xenotime which are the tailings of tin mines in the south of Thailand. Cerium is used mostly as lens polishing powder besides the applications in other industries. In this study, cerium extracted from monazite ore breakdown by alkaline process was used for the preparation of lens polishing powder. Cerium hydroxide cake from the process was dissolved by hydrochloric acid and precipitated with oxalic acid. The oxalate precipitate then was calcined to oxide powder and its particle size was measured. Precipitation conditions being studied are concentration of feed cerium chloride solution, concentration of oxalic acid used for the precipitation, concentration of sulfuric acid used as precipitation control reagent and the precipitation temperature. It was found that the appropriate precipitation conditions yielded the fine oxide powder with particle size about 12μm. The oxide powder can be ground to the size of 1-3 μm which is suitable for making lens polishing powder

21 CFR 73.1646 - Bronze powder.

Science.gov (United States)

2010-04-01

... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be based on the weight of the dried powder after being thoroughly washed with ether. (c) Uses and restrictions. Bronze powder may be safely used in color externally applied drugs, including those intended for...

Hydrothermal synthesis of fine oxide powders

Indian Academy of Sciences (India)

Unknown

Inorganic powders are among the most important factors in many fields of materials such as ceramics, catalysts, medicines, food, etc. There are many papers and books related to powders preparation by many authors (Veale. 1972; Kato and Yamaguchi 1983; Vincenzini 1983;. Brinker et al 1984; Johnson Jr. 1987; Messing ...

Aluminum powder size and microstructure effects on properties of boron nitride reinforced aluminum matrix composites fabricated by semi-solid powder metallurgy

International Nuclear Information System (INIS)

Chen, Cunguang; Guo, Leichen; Luo, Ji; Hao, Junjie; Guo, Zhimeng; Volinsky, Alex A.

2015-01-01

Al matrix composite reinforced by hexagonal boron nitride (h-BN) with nearly full densification was successfully fabricated by the semi-solid powder metallurgy technique. The h-BN/Al composites were synthesized with elemental pure Al powder size of d_5_0=35, 12 and 2 μm. The powder morphology and the structural characteristics of the composites were analyzed using X-ray diffraction, scanning and transmission electron microscopy. The density, Brinell hardness and compressive behavior of the samples were characterized. Density measurement of the Al composites revealed that the composite densification can be effectively promoted by plenty of embedded liquid phase under pressure. Composites prepared using Al powder with varying granularity showed different grain characteristics, and in situ recrystallization occurred inside the original grains with 35 μm Al powder. A sharp interface consisting of Al/Al_2O_3/h-BN was present in the composites. Both the compressive strength and the fracture strain of the investigated composites increased with the decrease of the Al powder size, along with the Brinell hardness. The composite with 2 μm Al powder exhibited the highest relative density (99.3%), Brinell harness (HB 128), compressive strength (763 MPa) and fracture strain (0.299).

Powder processing and spheroidizing with thermal inductively coupled plasma

International Nuclear Information System (INIS)

Nutsch, G.; Linke, P.; Zakharian, S.; Dzur, B.; Weiss, K.-H.

2001-01-01

Processing of advanced powder materials for the spraying industry is one of the most promising applications of the thermal RF inductively coupled plasma. By selecting the feedstock carefully and adjusting the RF plasma parameters, unique materials with high quality can be achieved. Powders injected in the hot plasma core emerge with modified shapes, morphology, crystal structure and chemical composition. Ceramic oxide powders such as Al 2 O 3 , ZrO 2 , SiO 2 are spheroidized with a high spheroidization rate. By using the RF induction plasma spheroidizing process tungsten melt carbide powders are obtained with a high spheroidization rate at high feeding rates by densification of agglomerated powders consisting of di-tungsten carbide and monocarbide with a definite composition. This kind of ball-like powders is particularly suited for wear resistant applications. (author)

Emerging Applications Using Magnesium Alloy Powders: A Feasibility Study

Science.gov (United States)

Tandon, Rajiv; Madan, Deepak

The use of powder metallurgy offers a potential processing route based on tailored compositions and unique microstructures to achieve high performance in magnesium alloys. This paper highlights recent advances in the production, qualification, and characterization of gas atomized AZ91E, WE43 and Elektron21 alloy powders. Transmission electron microscopy (TEM) was used to understand the bulk and surface structure of the atomized powder. The potential for using these magnesium alloy powders for emerging applications involves establishing compatibility with viable consolidation processes such as cold spray, laser assisted deposition, forging and extrusion. This study summarizes the preliminary results for various ongoing investigations using WE43 powder as an example. Results show that powder metallurgy processed WE43 results in comparable properties to those obtained from cast and wrought and offers potential for improvement.

Powder Metallurgy characteristics and application: state of the art

International Nuclear Information System (INIS)

Zaid, A.I.O.

2005-01-01

Powder metallurgy process (P/M) is a near-net or net-shape manufacturing process that combines the features of shape making technology of powder compaction with the development of final material and design properties (physical and mechanical) during subsequent densification or consolidation processes, e.g. sintering. It utilizes the metal powder or powders of metal alloys. In this paper, the major historical developments in P/M are reviewed and discussed. The main parameters involved in the process and their effects on the product characteristics are presented and discussed, which include: powders and methods of their production, particle size and shape, compressibility and additives, sintering temperature and time and finishing processes. The advantages and limitations of powder metallurgy are also presented and discussed. Finally, applications and future developments of the process are outlined and discussed. (author)

Methods for production of aluminium powders and their application fields

Energy Technology Data Exchange (ETDEWEB)

Gopienko, V.G.; Kiselev, V.P.; Zobnina, N.S. (Vsesoyuznyj Nauchno-Issledovatel' skij i Proektnyj Inst. Alyuminievoj, magnievoj i ehlektrodnoj promyshlennosti (USSR))

1984-12-01

Different types of powder products made of alluminium and its alloys (powder, fine powders, granules and pastes) as well as their basic physicochemical properties are briefly characterized. The principle methods for alluminium powder production are outlined: physicochemical methods, the melt spraying by compressed gas being the mostly developed among them, and physico-mechanical ones. Main application spheres for powder productions of aluminium and its alloys are reported in short.

Methods for production of aluminium powders and their application fields

International Nuclear Information System (INIS)

Gopienko, V.G.; Kiselev, V.P.; Zobnina, N.S.

1984-01-01

Different types of powder products made of alluminium and its alloys (powder, fine powders, granules and pastes) as well as their basic physicochemical properties are briefly characterized. The principle methods for alluminium powder production are outlined: physicochemical methods, the melt spraying by compressed gas being the mostly developed among them, and physico-mechanical ones. Main application spheres for powder productions of aluminium and its alloys are reported in short

Light as stress factor to plant roots – case of root halotropism

Science.gov (United States)

Yokawa, Ken; Fasano, Rossella; Kagenishi, Tomoko; Baluška, František

2014-01-01

Despite growing underground, largely in darkness, roots emerge to be very sensitive to light. Recently, several important papers have been published which reveal that plant roots not only express all known light receptors but also that their growth, physiology and adaptive stress responses are light-sensitive. In Arabidopsis, illumination of roots speeds-up root growth via reactive oxygen species-mediated and F-actin dependent process. On the other hand, keeping Arabidopsis roots in darkness alters F-actin distribution, polar localization of PIN proteins as well as polar transport of auxin. Several signaling components activated by phytohormones are overlapping with light-related signaling cascade. We demonstrated that the sensitivity of roots to salinity is altered in the light-grown Arabidopsis roots. Particularly, light-exposed roots are less effective in their salt-avoidance behavior known as root halotropism. Here we discuss these new aspects of light-mediated root behavior from cellular, physiological and evolutionary perspectives. PMID:25566292

30 CFR 56.6901 - Black powder.

Science.gov (United States)

2010-07-01

... flame; (ii) Within any building in which a fuel-fired or exposed-element electric heater is operating...; and (4) Opened only when the powder is being transferred to a blasthole or another container and only in locations not listed in paragraph (b)(3) of this section. (c) Black powder shall be transferred...

30 CFR 57.6901 - Black powder.

Science.gov (United States)

2010-07-01

... feet of any magazine or open flame; (ii) Within any building in which a fuel-fired or exposed-element electric heater is operating; or (iii) In an area where electrical or incandescent-particle sparks could result in powder ignition; and (4) Opened only when the powder is being transferred to a blasthole or...

Permanent magnets and its production by powder metallurgy

Directory of Open Access Journals (Sweden)

Enrique Herraiz Lalana

2018-06-01

Full Text Available In this work, the historical relationship between permanent magnets and powder metallurgy is reviewed. Powder metallurgy is a manufacturing technique based on the compaction of powders that are sintered to create a solid product. This technique was used in the production of permanent magnets for the first time in the 18th century and, nowadays, most permanent magnetic materials are manufacturing by this mean. Magnetic properties are highly dependent on the microstructure of the final product, the magnetic alignment of domains and presence of porosity, to mention a few, and powder metallurgy enables fine control of these factors.

Sorghum root-system classification in contrasting P environments reveals three main rooting types and root-architecture-related marker-trait associations.

Science.gov (United States)

Parra-Londono, Sebastian; Kavka, Mareike; Samans, Birgit; Snowdon, Rod; Wieckhorst, Silke; Uptmoor, Ralf

2018-02-12

Roots facilitate acquisition of macro- and micronutrients, which are crucial for plant productivity and anchorage in the soil. Phosphorus (P) is rapidly immobilized in the soil and hardly available for plants. Adaptation to P scarcity relies on changes in root morphology towards rooting systems well suited for topsoil foraging. Root-system architecture (RSA) defines the spatial organization of the network comprising primary, lateral and stem-derived roots and is important for adaptation to stress conditions. RSA phenotyping is a challenging task and essential for understanding root development. In this study, 19 traits describing RSA were analysed in a diversity panel comprising 194 sorghum genotypes, fingerprinted with a 90-k single-nucleotide polymorphism (SNP) array and grown under low and high P availability. Multivariate analysis was conducted and revealed three different RSA types: (1) a small root system; (2) a compact and bushy rooting type; and (3) an exploratory root system, which might benefit plant growth and development if water, nitrogen (N) or P availability is limited. While several genotypes displayed similar rooting types in different environments, others responded to P scarcity positively by developing more exploratory root systems, or negatively with root growth suppression. Genome-wide association studies revealed significant quantitative trait loci (P root-system development on chromosomes SBI-02 and SBI-03. Sorghum genotypes with a compact, bushy and shallow root system provide potential adaptation to P scarcity in the field by allowing thorough topsoil foraging, while genotypes with an exploratory root system may be advantageous if N or water is the limiting factor, although such genotypes showed highest P uptake levels under the artificial conditions of the present study. © The Author(s) 2018. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

The preparation of UO2 powder: effect of ammonium uranate properties

International Nuclear Information System (INIS)

Woolfrey, J.L.

1978-01-01

Ammonium uranate (AU) powders were precipitated from a uranyl nitrate solution with gaseous ammonia. The decomposition of the powders in hydrogen was studied to determine those properties of AU which affect the decomposition reactions and influence the properties of the final UO 2 powder. The thermal decomposition was affected by the initial composition (ammonia and nitrate content) and the morphology of the AU powders. The amount of self-reduction increased with increasing combined ammonia content and decreased with increasing nitrate content. The specific surface area of the decomposed powder increased with increasing total ammonia content and initial surface area of the precursor AU powder. Thermal treatment of the decomposed powder can be used to modify such effects and, in commercial powder production, is used to control the properties of the final UO 2 powder. (Auth.)

Continuous Process for Low-Cost, High-Quality YSZ Powder

Energy Technology Data Exchange (ETDEWEB)

Scott L. Swartz; Michael Beachy; Matthew M. Seabaugh

2006-03-31

This report describes results obtained by NexTech Materials, Ltd. in a project funded by DOE under the auspices of the Solid-State Energy Conversion Alliance (SECA). The project focused on development of YSZ electrolyte powder synthesis technology that could be ''tailored'' to the process-specific needs of different solid oxide fuel cell (SOFC) designs being developed by SECA's industry teams. The work in the project involved bench-scale processing work aimed at establishing a homogeneous precipitation process for producing YSZ electrolyte powder, scaleup of the process to 20-kilogram batch sizes, and evaluation of the YSZ powder products produced by the process. The developed process involved the steps of: (a) preparation of an aqueous hydrous oxide slurry via coprecipitation; (b) washing of residual salts from the precipitated hydroxide slurry followed by drying; (c) calcination of the dried powder to crystallize the YSZ powder and achieve desired surface area; and (d) milling of the calcined powder to targeted particle size. YSZ powders thus prepared were subjected to a comprehensive set of characterization and performance tests, including particle size distribution and surface area analyses, sintering performance studies, and ionic conductivity measurements. A number of different YSZ powder formulations were established, all of which had desirable performance attributes relative to commercially available YSZ powders. Powder characterization and performance metrics that were established at the onset of the project were met or exceeded. A manufacturing cost analysis was performed, and a manufactured cost of $27/kg was estimated based on this analysis. The analysis also allowed an identification of process refinements that would lead to even lower cost.

Psoralen production in hairy roots and adventitious roots cultures of Psoralea coryfolia.

Science.gov (United States)

Baskaran, P; Jayabalan, N

2009-07-01

Psoralea corylifolia is an endangered plant producing various compounds of medical importance. Adventitious roots and hairy roots were induced in cultures prepared from hypocotyl explants. Psoralen content was evaluated in both root types grown either in suspension cultures or on agar solidified medium. Psoralen content was approximately 3 mg g(-1) DW in suspension grown hairy roots being higher than in solid grown hairy roots and in solid and suspension-grown adventitious roots.

Nonsurgical management of horizontal root fracture associated external root resorption and internal root resorption

Directory of Open Access Journals (Sweden)

Shiraz Pasha

2016-01-01

Full Text Available Horizontal root fractures, which frequently affect the upper incisors, usually result from a frontal impact. As a result, combined injuries occur in dental tissues such as the pulp, dentin, cementum, periodontal ligament, and alveolar bone. Internal root canal inflammatory resorption involves a progressive loss of intraradicular dentin without adjunctive deposition of hard tissues adjacent to the resorptive sites. It is frequently associated with chronic pulpal inflammation, and bacteria might be identified from the granulation tissues when the lesion is progressive to the extent that it is identifiable with routine radiographs. With the advancement in technology, it is imperative to use modern diagnostic tools such as cone beam computed tomography and radiovisuography to diagnose and confirm the presence and extent of resorptions and fractures and their exact location. This case report presents a rare case having internal root resorption and horizontal root fracture with external inflammatory root resorption both which were treated successfully following guidelines by International Association of Dental Traumatology by nonsurgical treatment with 1 year follow-up.

Uranium Dioxide Powder Flow ability Improvement Using Sol-Gel

International Nuclear Information System (INIS)

Juanda, D.; Sambodo Daru, G.

1998-01-01

The improvement of flow ability characteristics of uranium dioxide powder has been done using sol-gel process. To anticipate a pellet mass production with uniform pellet dimension, the uranium dioxide powder must be have a spherical form. Uranium dioxide spherical powder has been diluted in acid transformed into sol colloidal solution. To obtain uranium dioxide spherical form, the uranium sol-colloidal solution has been dropped in a hot paraffin ( at the temperature of 90 0 C) to form gelatinous colloid and then dried at 800 0 C, and sintered at the temperature of 1700 0 C. The flow ability of spherical uranium dioxide powder has been examined by using Flowmeter Hall (ASTM. B. 213-46T). The measurement result reveals that the spherical uranium dioxide powder has a flow ability twice than that of unprocessed uranium dioxide powder

Dust generation in powders: Effect of particle size distribution

Directory of Open Access Journals (Sweden)

Chakravarty Somik

2017-01-01

Full Text Available This study explores the relationship between the bulk and grain-scale properties of powders and dust generation. A vortex shaker dustiness tester was used to evaluate 8 calcium carbonate test powders with median particle sizes ranging from 2μm to 136μm. Respirable aerosols released from the powder samples were characterised by their particle number and mass concentrations. All the powder samples were found to release respirable fractions of dust particles which end up decreasing with time. The variation of powder dustiness as a function of the particle size distribution was analysed for the powders, which were classified into three groups based on the fraction of particles within the respirable range. The trends we observe might be due to the interplay of several mechanisms like de-agglomeration and attrition and their relative importance.

OIL SOLUTIONS POWDER

Science.gov (United States)

Technical product bulletin: aka OIL SOLUTIONS POWDER, SPILL GREEN LS, this miscellaneous oil spill control agent used in cleanups initially behaves like a synthetic sorbent, then as a solidifier as the molecular microencapsulating process occurs.

High density UO2 powder preparation for HWR fuel

International Nuclear Information System (INIS)

Hwang, S. T.; Chang, I. S.; Choi, Y. D.; Cho, B. R.; Kwon, S. W.; Kim, B. H.; Moon, B. H.; Kim, S. D.; Phyu, K. M.; Lee, K. A.

1992-01-01

The objective of this project is to study on the preparation of method high density UO 2 powder for HWR Fuel. Accordingly, it is necessary to character ize the AUC processed UO 2 powder and to search method for the preparation of high density UO 2 powder for HWR Fuel. Therefore, it is expected that the results of this study can effect the producing of AUC processed UO 2 powder having sinterability. (Author)

Safe-geometry pneumatic nuclear fuel powder blender

International Nuclear Information System (INIS)

Lyon, W.L.

1979-01-01

The object of this invention is to provide a nuclear fuel powder mixing tank in which the powder can be rapidly and safely mixed and in which accumulation of critical amounts of fuel is prevented. (UK)

Determination of Dispersion of Zucchini and Cabbage Powders

Directory of Open Access Journals (Sweden)

M.I. Pogozhyh

2013-07-01

Full Text Available Particle size of cabbage and zucchini powders was determined by microscopy. It is shown that under the identical conditions of drying, grinding and other stages of the process, the cabbage powder has a higher content of fine fraction. Promising application of cabbage and zucchini powders in restaurant industry is indicated. Case diagram of the received production use is developed.

Pressurized Anneal of Consolidated Powders

Science.gov (United States)

Nemir, David Charles (Inventor); Rubio, Edward S. (Inventor); Beck, Jan Bastian (Inventor)

2017-01-01

Systems and methods for producing a dense, well bonded solid material from a powder may include consolidating the powder utilizing any suitable consolidation method, such as explosive shockwave consolidation. The systems and methods may also include a post-processing thermal treatment that exploits a mismatch between the coefficients of thermal expansion between the consolidated material and the container. Due to the mismatch in the coefficients, internal pressure on the consolidated material during the heat treatment may be increased.

Transport device for nuclear fuel powder

International Nuclear Information System (INIS)

Adelmann, M.

1987-01-01

The transport device for nuclear fuel powder, which does not disintegrate during transport, has a transport pipe which starts with its entry end from the floor or a closed container and opens with its outlet end at the top into a closed separation container connect via a powder filter to a suction pump. By alternate regular opening and closing of a first control valve for transport gas fitted to a transport pipe to a supply duct and a second control valve for transport gas fitted to the container to an additional supply duct, alternating plugs of nuclear fuel powder and transport gas cushions are formed and are transported to the outlet end of the transport pipe. (orig./HP) [de

ROOT Reference Documentation

CERN Document Server

Fuakye, Eric Gyabeng

2017-01-01

A ROOT Reference Documentation has been implemented to generate all the lists of libraries needed for each ROOT class. Doxygen has no option to generate or add the lists of libraries for each ROOT class. Therefore shell scripting and a basic C++ program was employed to import the lists of libraries needed by each ROOT class.

Polymer quenched prealloyed metal powder

Science.gov (United States)

Hajaligol, Mohammad R.; Fleischhauer, Grier; German, Randall M.

2001-01-01

A powder metallurgical process of preparing a sheet from a powder having an intermetallic alloy composition such as an iron, nickel or titanium aluminide. The sheet can be manufactured into electrical resistance heating elements having improved room temperature ductility, electrical resistivity, cyclic fatigue resistance, high temperature oxidation resistance, low and high temperature strength, and/or resistance to high temperature sagging. The iron aluminide has an entirely ferritic microstructure which is free of austenite and can include, in weight %, 4 to 32% Al, and optional additions such as .ltoreq.1% Cr, .gtoreq.0.05% Zr .ltoreq.2% Ti, .ltoreq.2% Mo, .ltoreq.1% Ni, .ltoreq.0.75% C, .ltoreq.0.1% B, .ltoreq.1% submicron oxide particles and/or electrically insulating or electrically conductive covalent ceramic particles, .ltoreq.1% rare earth metal, and/or .ltoreq.3 % Cu. The process includes forming a non-densified metal sheet by consolidating a powder having an intermetallic alloy composition such as by roll compaction, tape casting or plasma spraying, forming a cold rolled sheet by cold rolling the non-densified metal sheet so as to increase the density and reduce the thickness thereof and annealing the cold rolled sheet. The powder can be a water, polymer or gas atomized powder which is subjecting to sieving and/or blending with a binder prior to the consolidation step. After the consolidation step, the sheet can be partially sintered. The cold rolling and/or annealing steps can be repeated to achieve the desired sheet thickness and properties. The annealing can be carried out in a vacuum furnace with a vacuum or inert atmosphere. During final annealing, the cold rolled sheet recrystallizes to an average grain size of about 10 to 30 .mu.m. Final stress relief annealing can be carried out in the B2 phase temperature range.

Compactibility of atomized high-speed steel and steel 3 powders

International Nuclear Information System (INIS)

Kulak, L.D.; Gavrilenko, A.P.; Pikozh, A.P.; Kuz'menko, N.N.

1985-01-01

Spherical powders and powders of lammellar-scaly shape of high-speed R6M5K5 steel and steel 3 produced by the method of centrifugal atomization of a rotating billet under conditions of cold pressing in steel moulds are studied for thier compactability. Compacting pressure dependnences are establsihed for density of cold-pressed compacts of spherical and scaly powders. The powders of lammellar-scaly shape both of high-speed steel and steel 3 are found to possess better compactibility within a wide range of pressures as compared to powders of spherical shape. Compacts of the lammellar-scaly powders possess also higher mechanical strength

X-ray computed tomography uncovers root-root interactions: quantifying spatial relationships between interacting root systems in three dimensions.

Science.gov (United States)

Paya, Alexander M; Silverberg, Jesse L; Padgett, Jennifer; Bauerle, Taryn L

2015-01-01

Research in the field of plant biology has recently demonstrated that inter- and intra-specific interactions belowground can dramatically alter root growth. Our aim was to answer questions related to the effect of inter- vs. intra-specific interactions on the growth and utilization of undisturbed space by fine roots within three dimensions (3D) using micro X-ray computed tomography. To achieve this, Populus tremuloides (quaking aspen) and Picea mariana (black spruce) seedlings were planted into containers as either solitary individuals, or inter-/intra-specific pairs, allowed to grow for 2 months, and 3D metrics developed in order to quantify their use of belowground space. In both aspen and spruce, inter-specific root interactions produced a shift in the vertical distribution of the root system volume, and deepened the average position of root tips when compared to intra-specifically growing seedlings. Inter-specific interactions also increased the minimum distance between root tips belonging to the same root system. There was no effect of belowground interactions on the radial distribution of roots, or the directionality of lateral root growth for either species. In conclusion, we found that significant differences were observed more often when comparing controls (solitary individuals) and paired seedlings (inter- or intra-specific), than when comparing inter- and intra-specifically growing seedlings. This would indicate that competition between neighboring seedlings was more responsible for shifting fine root growth in both species than was neighbor identity. However, significant inter- vs. intra-specific differences were observed, which further emphasizes the importance of biological interactions in competition studies.

Process for fabricating mixed-oxide powders

International Nuclear Information System (INIS)

Elmaleh, D.; Giraudel, A.

1975-01-01

A physical-chemical process for fabricating homogeneous powders suitable for sintering is described. It can be applied to the synthesis of all mixed oxides having mutually compatible and water soluble salts. As a specific example, the fabrication of lead titanate-zirconate powders used to make hot pressed ceramics is described. These ceramics show improved piezoelectric properties [fr

Whey powder sterilization by ionizing irradiation

International Nuclear Information System (INIS)

Todorovic, M.; Salatic, Z.; Markov, S.

1988-01-01

Whey powder was sterilized by gamma waves application. As a source of irridiation isotope 60Co was used in Institute of Nuclear sciences B oris Kidrich , Vincha-Belgrade (Yugoslavia). The applied doses were: a, b, c, d, and e Kgy. The dose d was radappertization. After whey powder irradiation no adverse changes of organoleptic properties were noticed

Sysnthesis of powders by freeze-drying

International Nuclear Information System (INIS)

Johnson, S.M.; Gusman, M.I.; Hildenbrand, D.L.

1988-01-01

The freeze-drying method of synthesizing powders of the superconducting oxide YBa 2 Cu 3 O 7 - δ is described. This process produces homogeneous, submicron powders of high purity. The effects of salt selection, solution concentration and pH on the process are described. Some evaluation of the sintering behavior and the effects on critical current density are included

Tricalcium phosphate powder: Preparation, characterization and compaction abilities

Directory of Open Access Journals (Sweden)

Abida Fatima

2017-02-01

Full Text Available In this work, we characterize tricalcium phosphate powders Ca9(HPO4(PO45(OH resulting from a reaction between calcium hydroxide and orthophosphoric acid at room temperature, without pH adjustment and in absence of ionic impurities. The prepared powder has an atomic ratio Ca/P of 1.512 ± 0.005. The real density is 2.68 ± 0.02 g/cm3 and the specific surface area is 80 ± 02 m2/g. During compression, the microstructure of Ca-deficient apatite powder with the presence of HPO4 groups seems to support the cohesion between particles. The transmission ratio is 90%, the transfer ratio is 41.8 and the ratio of the die-wall friction is 0.22. These results show that apatitic tricalcium powder gives a good aptitude to the compaction which leads to a good tensile strength (0.79 MPa. The heat treatment of the prepared powder shows the precise temperature for the formation of pyrophosphate, β-TCP and α-TCPa phases.  The purity and aptitude to compaction of the prepared powders are very promising for pharmaceutical and medical applications.

Synthesis of ITO Powder by Dry Process and Lifetime Characteristics of the ITO Target Fabricated with its Powder

Science.gov (United States)

Takahashi, Seiichiro; Itoh, Hironori; Komatsu, Ryuichi

Lifetime of an indium tin oxide (ITO) target is an important characteristic in the production of liquid crystal displays (LCDs). Increasing the sintering density of the ITO target is assumed to lead to an increased lifetime. So far, it has been clarified that the carbon concentration in In2O3 powder, the raw material of ITO targets, influences remarkably the target lifetime. In this study, with the aim of reducing the concentration of carbon in In2O3 powder, the synthesis of In2O3 powder containing dissolved Sn by a dry process was performed.

Root hairs aid soil penetration by anchoring the root surface to pore walls.

Science.gov (United States)

Bengough, A Glyn; Loades, Kenneth; McKenzie, Blair M

2016-02-01

The physical role of root hairs in anchoring the root tip during soil penetration was examined. Experiments using a hairless maize mutant (Zea mays: rth3-3) and its wild-type counterpart measured the anchorage force between the primary root of maize and the soil to determine whether root hairs enabled seedling roots in artificial biopores to penetrate sandy loam soil (dry bulk density 1.0-1.5g cm(-3)). Time-lapse imaging was used to analyse root and seedling displacements in soil adjacent to a transparent Perspex interface. Peak anchorage forces were up to five times greater (2.5N cf. 0.5N) for wild-type roots than for hairless mutants in 1.2g cm(-3) soil. Root hair anchorage enabled better soil penetration for 1.0 or 1.2g cm(-3) soil, but there was no significant advantage of root hairs in the densest soil (1.5g cm(-3)). The anchorage force was insufficient to allow root penetration of the denser soil, probably because of less root hair penetration into pore walls and, consequently, poorer adhesion between the root hairs and the pore walls. Hairless seedlings took 33h to anchor themselves compared with 16h for wild-type roots in 1.2g cm(-3) soil. Caryopses were often pushed several millimetres out of the soil before the roots became anchored and hairless roots often never became anchored securely.The physical role of root hairs in anchoring the root tip may be important in loose seed beds above more compact soil layers and may also assist root tips to emerge from biopores and penetrate the bulk soil. © The Author 2016. Published by Oxford University Press on behalf of the Society for Experimental Biology.

The effect of particle structure on apparent density of electrolytic copper powder

Directory of Open Access Journals (Sweden)

K. I. POPOV

2001-12-01

Full Text Available The quantitative microstructural analysis and the sieve analysis of copper powder as well as the scanning electron microscopy analysis of the copper powders particles were performed. It was found that the structure of the copper powder particles determines the apparent density of copper powder. The powder particles from the same fractions of different powders occupy approximately the same volume, but the structure of metallic copper is very different. This causes the difference in apparent densities of copper powder obtained under different conditions. The more dendritic is the structure of powder particles the smaller is the apparent density of copper powder.

Measurements of water uptake of maize roots: the key function of lateral roots

Science.gov (United States)

Ahmed, M. A.; Zarebanadkouki, M.; Kroener, E.; Kaestner, A.; Carminati, A.

2014-12-01

Maize (Zea mays L.) is one of the most important crop worldwide. Despite its importance, there is limited information on the function of different root segments and root types of maize in extracting water from soils. Therefore, the aim of this study was to investigate locations of root water uptake in maize. We used neutron radiography to: 1) image the spatial distribution of maize roots in soil and 2) trace the transport of injected deuterated water (D2O) in soil and roots. Maizes were grown in aluminum containers (40×38×1 cm) filled with a sandy soil. When the plants were 16 days old, we injected D2O into selected soil regions containing primary, seminal and lateral roots. The experiments were performed during the day (transpiring plants) and night (not transpiring plants). The transport of D2O into roots was simulated using a new convection-diffusion numerical model of D2O transport into roots. By fitting the observed D2O transport we quantified the diffusional permeability and the water uptake of the different root segments. The maize root architecture consisted of a primary root, 4-5 seminal roots and many lateral roots connected to the primary and seminal roots. Laterals emerged from the proximal 15 cm of the primary and seminal roots. Water uptake occurred primarily in lateral roots. Lateral roots had the highest diffusional permeability (9.4×10-7), which was around six times higher that the diffusional permeability of the old seminal segments (1.4×10-7), and two times higher than the diffusional permeability of the young seminal segments (4.7×10-7). The radial flow of D2O into the lateral (6.7×10-5 ) was much higher than in the young seminal roots (1.1×10-12). The radial flow of D2O into the old seminal was negligible. We concluded that the function of the primary and seminal roots was to collect water from the lateral roots and transport it to the shoot. A maize root system with lateral roots branching from deep primary and seminal roots would be

Confirmation test of powder mixing process in J-MOX

International Nuclear Information System (INIS)

Ota, Hiroshi; Osaka, Shuichi; Kurita, Ichiro

2009-01-01

Japan Nuclear Fuel Ltd. (hereafter, JNFL) MOX Fuel Fabrication Plant (hereafter, J-MOX) is what fabricates MOX fuel for domestic light water power plants. Development of design concept of J-MOX was started mid 90's and the frame of J-MOX process was clarified around 2000 including adoption of MIMAS process as apart of J-MOX powder process. JNFL requires to take an answer to any technical question that has not been clarified ever before by world's MOX and/or Uranium fabricators before it commissions equipment procurement. J-MOX is to be constructed adjacent to the Rokkasho Reprocessing Plant (RRP) and to utilize MH-MOX powder recovered at RRP. The combination of the MIMAS process and the MH-MOX powder is what has never tried in the world. Therefore JNFL started a series of confirmation tests of which the most important is the powder test to confirm the applicability of MH-MOX powder to the MIMAS process. The MH-MOX powder, consisting of 50% plutonium oxide and 50% uranium oxide, originates JAEA development utilizing microwave heating (MH) technology. The powder test started with laboratory scale small equipment utilizing both uranium and the MOX powder in 2000, left a solution to tough problem such as powder adhesion onto equipment, and then was followed by a large scale equipment test again with uranium and the MOX powder. For the MOX test, actual size equipment within glovebox was manufactured and installed in JAEA plutonium fuel center in 2005, and based on results taken so far an understanding that the MIMAS equipment, with the MH-MOX powder, can present almost same quality MOX pellet as what is introduced as fabricated in Europe was developed. The test was finished at the end of Japanese fiscal year (JFY) 2007, and it was confirmed that the MOX pellets fabricated in this test were almost satisfied with the targeted specifications set for domestic LWR MOX fuels. (author)

POWDER INJECTION MOLDING OF SIC FOR THERMAL MANAGEMENT V

Directory of Open Access Journals (Sweden)

Valmikanathan Onbattuvelli

2012-06-01

Full Text Available Silicon carbide (SiC exhibits many functional properties that are relevant to applications in electronics, aerospace, defense and automotive industries. However, the successful translation of these properties into final applications lies in the net-shaping of ceramics into fully dense microstructures. Increasing the packing density of the starting powders is one effective route to achieve high sintered density and dimensional precision. The present paper presents an in-depth study on the effects of nanoparticle addition on the powder injection molding process (PIM of SiC powder-polymer mixtures. In particular, bimodal mixtures of nanoscale and sub-micrometer particles are found to have significantly increased powder packing characteristics (solids loading in the powder-polymer mixtures. The influence of nanoparticle addition on the multi-step PIM process is examined. The above results provide new perspectives which could impact a wide range of materials, powder processing techniques and applications.

RF induction plasma spheroidization of tungsten powders

International Nuclear Information System (INIS)

Gu Zhogntao; Ye Gaoying; Liu Chuandong; Tong Honghui

2009-01-01

Irregularly-shaped tungsten powders (average granular sizes of 512 μm) have been spheroidized by radio frequency (RF)induction plasma. The effects of feed rate, mode of material dispersion, particle size on spheroidization efficiency are investigated. Experimental results show that the spheroidization efficiency decreases rapidly when the feed rate increases to more than 95 g/min. Only 30% spheroidization efficiency is gained at the feed rate of 135.75 g/min. The spheroidization efficiency is also affected by the flow rate of carrier gas. When the flow rate of carrier gas is 0.12 m 3 /h, the dispersion effect is the best, and the spheroidization efficiency is almost 100%. The apparent density of tungsten powders increases a bit with the increase of spheroidization efficiency. And the particle size uniformity of spheroidized tungsten powders is in accordance with that of original powders. (authors)

Synthesis of battery grade reduced silver powder

International Nuclear Information System (INIS)

Qadeer, R.; Hameed, M.; Ikram, S.; Munir, A.

2002-01-01

Process for production of battery grade reduced silver powder, an active positive material for zinc-silver oxide batteries, having specific characteristics has been optimized and the synthesized reduced silver powder was characterized. Results reveal that the values of bulk density (1.25 0.1 g/cm3) and activity (73.27 %) of synthesized reduced silver powder lies within the recommended range for use as battery material. It has purity ≥ 98% and contains Fe and Cu as traces in the concentration range of 30 5 ppm and 15 7 ppm respectively. Others determined values of surface and pores parameters are: surface area 2.6 .4 m2/g: pore volume 3.10 cm3/g: pore diameter 0.043 mu m and porosity 20%. XRD studies reveal that reduced silver powder has a cubic structure. (author)

Heat Treatment of Gas-Atomized Powders for Cold Spray Deposition

Science.gov (United States)

Story, William A.; Brewer, Luke N.

2018-02-01

This communication demonstrates the efficacy of heat treatment on the improved deposition characteristics of aluminum alloy powders. A novel furnace was constructed for solutionizing of feedstock powders in an inert atmosphere while avoiding sintering. This furnace design achieved sufficiently high cooling rates to limit re-precipitation during powder cooling. Microscopy showed homogenization of the powder particle microstructures after heat treatment. Cold spray deposition efficiency with heat-treated powders substantially increased for the alloys AA2024, AA6061, and AA7075.

Nanograin formation in milled MoO3 powders

International Nuclear Information System (INIS)

Guerrero-Paz, J; Dorantes-Rosales, H; Aguilar-Martínez, J A; Garibay-Febles, V

2013-01-01

Powder of Molybdenum trioxide was milled for different times in horizontal ball mills. Such powder was characterized by TEM and XRD. Powder was rapidly de-agglomerated and fragmented up to attain nanoplates of two types, amorphous and crystalline. Finally, cold-welding of nanoplates occurred permitting some relaxation process to obtain a more stable energized structure consisting of equiaxial crystalline nanograins after 16 hours of milling.

Rapidly solidified prealloyed powders by laser spin atomization

Science.gov (United States)

Konitzer, D. G.; Walters, K. W.; Heiser, E. L.; Fraser, H. L.

1984-01-01

A new technique, termed laser spin atomization, for the production of rapidly solidified prealloyed powders is described. The results of experiments involving the production of powders of two alloys, one based on Ni, the other on Ti, are presented. The powders have been characterized using light optical metallography, scanning electron microscopy, energy dispersive X-ray spectroscopy, and Auger elec-tron spectroscopy, and these various observations are described.

Measurement of agglomerate strength distributions in agglomerated powders

International Nuclear Information System (INIS)

Ciftcioglu, M.; Aking, M.; Burkhart, L.

1986-01-01

Strength distributions of particle agglomerates in six different yttria powders were measured using a calibrated ultrasonic sound field. The density of sintered pellets was directly related to the agglomerate strength of each powder. No systematic relation to the sintered density was observed for bulk densities or pressure-density compaction data for the loose powders, or for pore size distributions or green densities for the pressed compacts

Ninety Years of Powder Diffraction: from Birth to Maturity

International Nuclear Information System (INIS)

Paszkowicz, W.

2006-01-01

The expression ''powder diffraction '' denotes the phenomenon of diffraction of any electromagnetic waves or particles on polycrystalline (powdered, bulk or thin film) materials which is used in a wide variety experimental settings. The X-ray powder-diffraction method was devised and developed during the First World War (1916) by a Dutch/Swiss team, Peter Debye and Paul Scherrer, in Goettingen, Germany, and independently, marginally later, by an American, Albert W. Hull in Schenectady, USA. The birth of powder diffraction came four years after the discovery of the phenomenon of single-crystal diffraction made in 1912 by Walther Friedrich, Paul Knipping and Max Laue in Munich and developed from 1912/1913 by William Henry Bragg (father) and William Lawrence Bragg (son), and later by many others. Powder diffraction became a milestone towards an understanding of the nature of materials, especially of those which cannot be prepared in the form of suitable single crystals, and permitted rapid progress in solid state physics and chemistry. The events leading to the discovery of powder-diffraction phenomenon are briefly reviewed. The importance of synchrotron powder diffraction studies, which have developed since 1980s, is emphasised. (author)

Conjoined lumbosacral nerve roots

International Nuclear Information System (INIS)

Kyoshima, Kazumitsu; Nishiura, Iwao; Koyama, Tsunemaro

1986-01-01

Several kinds of the lumbosacral nerve root anomalies have already been recognized, and the conjoined nerve roots is the most common among them. It does not make symptoms by itself, but if there is a causation of neural entrapment, for example, disc herniation, lateral recessus stenosis, spondylolisthesis, etc., so called ''biradicular syndrome'' should occur. Anomalies of the lumbosacral nerve roots, if not properly recognized, may lead to injury of these nerves during operation of the lumbar spine. Recently, the chance of finding these anomalous roots has been increased more and more with the use of metrizamide myelography and metrizamide CT, because of the improvement of the opacification of nerve roots. We describe the findings of the anomalous roots as revealed by these two methods. They demonstrate two nerve roots running parallel and the asymmetrical wide root sleeve. Under such circumstances, it is important to distinguish the anomalous roots from the normal ventral and dorsal roots. (author)

IAA transport in corn roots includes the root cap

International Nuclear Information System (INIS)

Hasenstein, K.H.

1989-01-01

In earlier reports we concluded that auxin is the growth regulator that controls gravicurvature in roots and that the redistribution of auxin occurs within the root cap. Since other reports did not detect auxin in the root cap, we attempted to confirm the IAA does move through the cap. Agar blocks containing 3 H-IAA were applied to the cut surface of 5 mm long apical segments of primary roots of corn (mo17xB73). After 30 to 120 min radioactivity (RA) of the cap and root tissue was determined. While segments suspended in water-saturated air accumulated very little RA in the cap, application of 0.5 μ1 of dist. water to the cap (=controls) increased RA of the cap dramatically. Application to the cap of 0.5 μ1 of sorbitol or the Ca 2+ chelator EGTA reduced cap RA to 46% and 70% respectively compared to water, without affecting uptake. Control root segments gravireacted faster than non-treated or osmoticum or EGTA treated segments. The data indicate that both the degree of hydration and calcium control the amount of auxin moving through the cap

Preparation of reactive and refractory metal powders (Paper No. 25)

International Nuclear Information System (INIS)

Sundaram, C.V.; Sharma, B.P.; Krishnan, T.S.

1979-01-01

In devising processes for the preparation of refractory and reactive metal powders, one has to reckon with many relevant factors. The choice of specific flowsheets is governed by the characteristics of the metal compounds and the reducing agents, the purity required and achievable in the as-reduced powder, the need for further refining of the metal, the possibilities of chemical/physical/mechanical comminution of the purified metal without contamination, and the end application of the powder metal. Micron size zirconium powder used as trigger material in photo-flash bulbs and detonator compositions, tantalum powder of controlled particle size and high purity for the production of electrolytic capacitors, and beryllium metal powder for the preparation of hot pressed powder metallurgy components are illustrative of the variety of reactive metal powders for industrial applications. The work carried out at the Bhabha Atomic Research Centre, Bombay, on the preparation of special metal powders, with particular emphasis on Group IV and V metals and also beryllium is presented. Reduction of metal oxides with alkaline earth metals/hydrides, reduction of metal halides with sodium/magnesium, vacuum arc and electron beam melt purification followed by comminution by hydrogen embrittlement/mechanical comminution are among the processes discussed. (auth.)

POWDER COAT APPLICATIONS

Science.gov (United States)

The report discusses an investigation of critical factors that affect the use of powder coatings on the environment, cost, quality, and production. The investigation involved a small business representative working with the National Defense Center for Environmental Excellence (ND...

Powder Metallurgy Fabrication of Molybdenum Accelerator Target Disks

Energy Technology Data Exchange (ETDEWEB)

Lowden, Richard Andrew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kiggans Jr., James O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nunn, Stephen D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Parten, Randy J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-07-01

Powder metallurgy approaches for the fabrication of accelerator target disks are being examined to support the development of Mo-99 production by NorthStar Medical Technologies, LLC. An advantage of powder metallurgy is that very little material is wasted and, at present, dense, quality parts are routinely produced from molybdenum powder. The proposed targets, however, are thin wafers, 29 mm in diameter with a thickness of 0.5 mm, with very stringent dimensional tolerances. Although tooling can be machined to very high tolerance levels, the operations of powder feed, pressing and sintering involve complicated mechanisms, each of which affects green density and shrinkage, and therefore the dimensions and shape of the final product. Combinations of powder morphology, lubricants and pressing technique have been explored to produce target disks with minimal variations in thickness and little or no distortion. In addition, sintering conditions that produce densities for optimum target dissolvability are being determined.

Comparative studies of industrial grade carbon black powders

Energy Technology Data Exchange (ETDEWEB)

Chawla, Komal, E-mail: komalchawla.rs@gmail.com; Chauhan, Alok P. S., E-mail: chauhan.alok@gmail.com, E-mail: alok.chauhan@alumni.stonybrook.edu [Department of Physics and Material Science and Engineering, Jaypee Institute of Information Technology, A-10, Sector-62, Noida-201307, UP, India. (India)

2016-05-06

Comparative studies of two dissimilar industrial grade Carbon Black (CB) powders (N375 and N405) were conducted. The structure, surface area and particle size are the three important characteristics of CB powder that determine their processability and application as filler in preparing rubber compounds. The powders were characterized for their structure using dibutyl phthalate absorption (DBPA), particle size via laser particle size analyzer and surface area by nitrogen adsorption method. The structural characterization showed that N405 had lower DBPA in comparison to N375, confirming low structure of N405 grade CB powder. It was observed from the particle size analysis that N375 was coarser than N405 grade CB. The total surface area values were determined by the BET method based on the cross sectional area of the nitrogen molecule. N375, a coarse grade CB powder with high structure, depicted less surface area as compared to N405.

The use of glass powder in making batako

Science.gov (United States)

Nursyamsi, N.; Indrawan, I.

2018-02-01

Along with the increase in construction materials, innovation is needed to lessen the use of them, and one of them is by using cement [1]. In this research, it is reduced by glass powder; the reason for using it as the substitution of cement is that some chemical elements in cement are similar to those in glass powder such as SiO2, A12o3, Fe2O3, and CaO. The glass powder used was the one who passed sieve no. 100 and was hampered in sieve no. 200. It passed sieve no. 200 with its composition of 0%, 10%, 15%, 20%, 25%, and 30% from the volume of the use of cement. The specimen would treat within 28 days before the testing of compressive strength, water absorption, and tensile strength [2]. The variation which produced optimum result would mix with the foaming agent as the material for reducing the weight of the specimen. After that, the test of compressive strength, water absorption, and tensile strength on the installment of batako walls were done. The data analyzed by using SNI 02-0349-1989[3] reference about concrete brick for wall installment. The variation of 20% of glass powder passing sieve no. 200 gave optimum result. A specimen of the variation on glass powder of 20% which passed sieve no. 200 and the foaming agent was higher than the compressive strength of the specimen which used glass powder substitution of 0% of passing sieve no. 200 and foaming agent. The compressive strength of batako walls which used the batako construction with glass powder substitution of 20% of passing sieve no. 200 and the foaming agent was also higher than the compressive strength of the assaying object which used glass powder substitution of 0% of passing sieve no. 200 and foaming agent.

Root anatomical phenes predict root penetration ability and biomechanical properties in maize (Zea Mays)

OpenAIRE

Chimungu, Joseph G.; Loades, Kenneth W.; Lynch, Jonathan P.

2015-01-01

The ability of roots to penetrate hard soil is important for crop productivity but specific root phenes contributing to this ability are poorly understood. Root penetrability and biomechanical properties are likely to vary in the root system dependent on anatomical structure. No information is available to date on the influence of root anatomical phenes on root penetrability and biomechanics. Root penetration ability was evaluated using a wax layer system. Root tensile and bending strength we...

GLO-Roots: an imaging platform enabling multidimensional characterization of soil-grown root systems

Science.gov (United States)

Rellán-Álvarez, Rubén; Lobet, Guillaume; Lindner, Heike; Pradier, Pierre-Luc; Sebastian, Jose; Yee, Muh-Ching; Geng, Yu; Trontin, Charlotte; LaRue, Therese; Schrager-Lavelle, Amanda; Haney, Cara H; Nieu, Rita; Maloof, Julin; Vogel, John P; Dinneny, José R

2015-01-01

Root systems develop different root types that individually sense cues from their local environment and integrate this information with systemic signals. This complex multi-dimensional amalgam of inputs enables continuous adjustment of root growth rates, direction, and metabolic activity that define a dynamic physical network. Current methods for analyzing root biology balance physiological relevance with imaging capability. To bridge this divide, we developed an integrated-imaging system called Growth and Luminescence Observatory for Roots (GLO-Roots) that uses luminescence-based reporters to enable studies of root architecture and gene expression patterns in soil-grown, light-shielded roots. We have developed image analysis algorithms that allow the spatial integration of soil properties, gene expression, and root system architecture traits. We propose GLO-Roots as a system that has great utility in presenting environmental stimuli to roots in ways that evoke natural adaptive responses and in providing tools for studying the multi-dimensional nature of such processes. DOI: http://dx.doi.org/10.7554/eLife.07597.001 PMID:26287479

ROOT.NET: Using ROOT from .NET languages like C# and F#

Science.gov (United States)

Watts, G.

2012-12-01

ROOT.NET provides an interface between Microsoft's Common Language Runtime (CLR) and .NET technology and the ubiquitous particle physics analysis tool, ROOT. ROOT.NET automatically generates a series of efficient wrappers around the ROOT API. Unlike pyROOT, these wrappers are statically typed and so are highly efficient as compared to the Python wrappers. The connection to .NET means that one gains access to the full series of languages developed for the CLR including functional languages like F# (based on OCaml). Many features that make ROOT objects work well in the .NET world are added (properties, IEnumerable interface, LINQ compatibility, etc.). Dynamic languages based on the CLR can be used as well, of course (Python, for example). Additionally it is now possible to access ROOT objects that are unknown to the translation tool. This poster will describe the techniques used to effect this translation, along with performance comparisons, and examples. All described source code is posted on the open source site CodePlex.

ROOT.NET: Using ROOT from .NET languages like C and F

International Nuclear Information System (INIS)

Watts, G

2012-01-01

ROOT.NET provides an interface between Microsoft's Common Language Runtime (CLR) and .NET technology and the ubiquitous particle physics analysis tool, ROOT. ROOT.NET automatically generates a series of efficient wrappers around the ROOT API. Unlike pyROOT, these wrappers are statically typed and so are highly efficient as compared to the Python wrappers. The connection to .NET means that one gains access to the full series of languages developed for the CLR including functional languages like F (based on OCaml). Many features that make ROOT objects work well in the .NET world are added (properties, IEnumerable interface, LINQ compatibility, etc.). Dynamic languages based on the CLR can be used as well, of course (Python, for example). Additionally it is now possible to access ROOT objects that are unknown to the translation tool. This poster will describe the techniques used to effect this translation, along with performance comparisons, and examples. All described source code is posted on the open source site CodePlex.

Colloidal characterization of ultrafine silicon carbide and silicon nitride powders

Science.gov (United States)

Whitman, Pamela K.; Feke, Donald L.

1986-01-01

The effects of various powder treatment strategies on the colloid chemistry of aqueous dispersions of silicon carbide and silicon nitride are examined using a surface titration methodology. Pretreatments are used to differentiate between the true surface chemistry of the powders and artifacts resulting from exposure history. Silicon nitride powders require more extensive pretreatment to reveal consistent surface chemistry than do silicon carbide powders. As measured by titration, the degree of proton adsorption from the suspending fluid by pretreated silicon nitride and silicon carbide powders can both be made similar to that of silica.

Plant dried powders as biocatalysts: Hydrolysis of 1- phenylpropanol ...

African Journals Online (AJOL)

The hydrolytic ability of plant dried powders, lyophilized or acetone dried, was tested on the hydrolysis of racemic 1-phenylpropanol acetate. Most of the twenty powders tested showed hydrolytic activity, however the best values of conversion and enantioselectivity were reached with the lyophilized powder of nopal (27% ...

Peculiarities of powder metallurgy of vanadium and its alloys

International Nuclear Information System (INIS)

Radomysel'skij, I.D.; Solntsev, V.P.; Evtushenko, O.V.

1987-01-01

Literature data on preparation of vanadium powder and powder materials on the vanadium base are generalized. Application of powder metallurgy engineering, allowing simulaneously to introduce practically any strengthening and solid-lubricating components as well as to alloy vanadium, permits undoubtedly to develop composite materials on the vanadium base

Locally Finite Root Supersystems

OpenAIRE

Yousofzadeh, Malihe

2013-01-01

We introduce the notion of locally finite root supersystems as a generalization of both locally finite root systems and generalized root systems. We classify irreducible locally finite root supersystems.

Set up of Uranium-Molybdenum powder production (HMD process)

International Nuclear Information System (INIS)

Lopez, Marisol; Pasqualini, Enrique E.; Gonzalez, Alfredo G.

2003-01-01

Powder metallurgy offers different alternatives for the production of Uranium-Molybdenum (UMo) alloy powder in sizes smaller than 150 microns. This powder is intended to be used as a dispersion fuel in an aluminum matrix for research, testing and radioisotopes production reactors (MTR). A particular process of massive hydriding the UMo alloy in gamma phase has been developed. This work describes the final adjustments of process variables to obtain UMo powder by hydriding-milling-de hydriding (HMD) and its capability for industrial scaling up. (author)

Descendant root volume varies as a function of root type: estimation of root biomass lost during uprooting in Pinus pinaster

OpenAIRE

Danjon, Frédéric; Caplan, Joshua S.; Fortin, Mathieu; Meredieu, Céline

2013-01-01

Root systems of woody plants generally display a strong relationship between the cross-sectional area or cross-sectional diameter (CSD) of a root and the dry weight of biomass (DWd) or root volume (Vd) that has grown (i.e., is descendent) from a point. Specification of this relationship allows one to quantify root architectural patterns and estimate the amount of material lost when root systems are extracted from the soil. However, specifications of this relationship generally do not account ...

Laser Processing Technology using Metal Powders

Energy Technology Data Exchange (ETDEWEB)

Jang, Jeong-Hwan; Moon, Young-Hoon [Pusan National University, Busan (Korea, Republic of)

2012-03-15

The purpose of this paper is to review the state of laser processing technology using metal powders. In recent years, a series of research and development efforts have been undertaken worldwide to develop laser processing technologies to fabricate metal-based parts. Layered manufacturing by the laser melting process is gaining ground for use in manufacturing rapid prototypes (RP), tools (RT) and functional end products. Selective laser sintering / melting (SLS/SLM) is one of the most rapidly growing rapid prototyping techniques. This is mainly due to the processes's suitability for almost any materials, including polymers, metals, ceramics and many types of composites. The interaction between the laser beam and the powder material used in the laser melting process is one of the dominant phenomena defining feasibility and quality. In the case of SLS, the powder is not fully melted during laser scanning, therefore the SLS-processed parts are not fully dense and have relatively low strength. To overcome this disadvantage, SLM and laser cladding (LC) processes have been used to enable full melting of the powder. Further studies on the laser processing technology will be continued due to the many potential applications that the technology offers.

Roots & Hollers

OpenAIRE

Kollman, Patrick L; Gorman, Thomas A

2011-01-01

Roots & Hollers, 2011 A documentary by Thomas Gorman & Patrick Kollman Master’s Project Abstract: Roots & Hollers uncovers the wild American ginseng trade, revealing a unique intersection between Asia and rural America. Legendary in Asia for its healing powers, ginseng helps sustain the livelihoods of thousands in Appalachia. A single root can sell for thousands of dollars at auction. Shot on-location in the mountains of Kentucky and West Virginia, this student doc...

Synthesis of Cu-coated Graphite Powders Using a Chemical Reaction Process

Energy Technology Data Exchange (ETDEWEB)

Jang, Jun-Ho; Park, Hyun-Kuk; Oh, Ik-Hyun [Korea Institute of Industrial Technology (KITECH), Gwangju (Korea, Republic of); Lim, Jae-Won [Chonbuk National University, Jeonju (Korea, Republic of)

2017-05-15

In this paper, Cu-coated graphite powders for a low thermal expansion coefficient and a high thermal conductivity are fabricated using a chemical reaction process. The Cu particles adhere to the irregular graphite powders and they homogeneously disperse in the graphite matrix. Cu-coated graphite powders are coarser at approximately 3-4 μm than the initial graphite powders; furthermore, their XRD patterns exhibit a low intensity in the oxide peak with low Zn powder content. For the passivation powders, the transposition solvent content has low values, and the XRD pattern of the oxide peaks is almost non-existent, but the high transposition solvent content does not exhibit a difference to the non-passivation treated powders.

Slow stress relaxation behavior of cohesive powders

NARCIS (Netherlands)

Imole, Olukayode Isaiah; Paulick, Maria; Magnanimo, Vanessa; Morgenmeyer, Martin; Ramaioli, Marco; Chavez Montes, Bruno E.; Kwade, Arno; Luding, Stefan

2016-01-01

We present uniaxial (oedometric) compression tests on two cohesive industrially relevant granular materials (cocoa and limestone powder). A comprehensive set of experiments is performed using two devices – the FT4 Powder Rheometer and the custom made lambdameter – in order to investigate the

Characterization of Pearl Millet Root Architecture and Anatomy Reveals Three Types of Lateral Roots

Science.gov (United States)

Passot, Sixtine; Gnacko, Fatoumata; Moukouanga, Daniel; Lucas, Mikaël; Guyomarc’h, Soazig; Ortega, Beatriz Moreno; Atkinson, Jonathan A.; Belko, Marème N.; Bennett, Malcolm J.; Gantet, Pascal; Wells, Darren M.; Guédon, Yann; Vigouroux, Yves; Verdeil, Jean-Luc; Muller, Bertrand; Laplaze, Laurent

2016-01-01

Pearl millet plays an important role for food security in arid regions of Africa and India. Nevertheless, it is considered an orphan crop as it lags far behind other cereals in terms of genetic improvement efforts. Breeding pearl millet varieties with improved root traits promises to deliver benefits in water and nutrient acquisition. Here, we characterize early pearl millet root system development using several different root phenotyping approaches that include rhizotrons and microCT. We report that early stage pearl millet root system development is characterized by a fast growing primary root that quickly colonizes deeper soil horizons. We also describe root anatomical studies that revealed three distinct types of lateral roots that form on both primary roots and crown roots. Finally, we detected significant variation for two root architectural traits, primary root lenght and lateral root density, in pearl millet inbred lines. This study provides the basis for subsequent genetic experiments to identify loci associated with interesting early root development traits in this important cereal. PMID:27379124

Synthesis and characterization of superconducting YBCO powder

International Nuclear Information System (INIS)

Praveen, B.; Karki, T.; Krishnamoorthi, J.

2008-01-01

Full text: Superconducting yttrium barium copper oxide power has been synthesized through solid state sintering method - milling and sintering - using Y 2 O 3 , BaCo 3 and CuO powders. XRD result of the milled and sintered powder reveals that the powder that has formed contains YBa 2 Cu 3 O 6.5 superconducting phase. Results obtained by SEM/EDAX show the distribution of the different elements. Experiments carried out by intermediate firing and final annealing in oxygen controlled atmosphere show the diffusion of oxygen in preformed YBa 2 Cu 3 O 6.5 and their results are discussed

Hypocotyl adventitious root organogenesis differs from lateral root development.

Science.gov (United States)

Verstraeten, Inge; Schotte, Sébastien; Geelen, Danny

2014-01-01

Wound-induced adventitious root (AR) formation is a requirement for plant survival upon root damage inflicted by pathogen attack, but also during the regeneration of plant stem cuttings for clonal propagation of elite plant varieties. Yet, adventitious rooting also takes place without wounding. This happens for example in etiolated Arabidopsis thaliana hypocotyls, in which AR initiate upon de-etiolation or in tomato seedlings, in which AR initiate upon flooding or high water availability. In the hypocotyl AR originate from a cell layer reminiscent to the pericycle in the primary root (PR) and the initiated AR share histological and developmental characteristics with lateral roots (LRs). In contrast to the PR however, the hypocotyl is a determinate structure with an established final number of cells. This points to differences between the induction of hypocotyl AR and LR on the PR, as the latter grows indeterminately. The induction of AR on the hypocotyl takes place in environmental conditions that differ from those that control LR formation. Hence, AR formation depends on differentially regulated gene products. Similarly to AR induction in stem cuttings, the capacity to induce hypocotyl AR is genotype-dependent and the plant growth regulator auxin is a key regulator controlling the rooting response. The hormones cytokinins, ethylene, jasmonic acid, and strigolactones in general reduce the root-inducing capacity. The involvement of this many regulators indicates that a tight control and fine-tuning of the initiation and emergence of AR exists. Recently, several genetic factors, specific to hypocotyl adventitious rooting in A. thaliana, have been uncovered. These factors reveal a dedicated signaling network that drives AR formation in the Arabidopsis hypocotyl. Here we provide an overview of the environmental and genetic factors controlling hypocotyl-born AR and we summarize how AR formation and the regulating factors of this organogenesis are distinct from LR

Hypocotyl adventitious root organogenesis differs from lateral root development

Directory of Open Access Journals (Sweden)

Inge eVerstraeten

2014-09-01

Full Text Available Wound-induced adventitious root (AR formation is a requirement for plant survival upon root damage inflicted by pathogen attack, but also during the regeneration of plant stem cuttings for clonal propagation of elite plant varieties. Yet, adventitious rooting also takes place without wounding. This happens for example in etiolated Arabidopsis thaliana hypocotyls, in which AR initiate upon de-etiolation or in tomato seedlings, in which AR initiate upon flooding or high water availability. In the hypocotyl AR originate from a cell layer reminiscent to the pericycle in the primary root (PR and the initiated AR share histological and developmental characteristics with lateral roots (LR. In contrast to the PR however, the hypocotyl is a determinate structure with an established final number of cells. This points to differences between the induction of hypocotyl AR and LR on the PR, as the latter grows indeterminately. The induction of AR on the hypocotyl takes place in environmental conditions that differ from those that control LR formation. Hence, AR formation depends on differentially regulated gene products. Similarly to AR induction in stem cuttings, the capacity to induce hypocotyl AR is genotype-dependent and the plant growth regulator auxin is a key regulator controlling the rooting response. The hormones cytokinins, ethylene, jasmonic acid and strigolactones in general reduce the root-inducing capacity. The involvement of this many regulators indicates that a tight control and fine-tuning of the initiation and emergence of AR exists. Recently, several genetic factors, specific to hypocotyl adventitious rooting in Arabidopsis thaliana, have been uncovered. These factors reveal a dedicated signaling network that drives AR formation in the Arabidopsis hypocotyl. Here we provide an overview of the environmental and genetic factors controlling hypocotyl-born AR and we summarize how AR formation and the regulating factors of this organogenesis are

ROOT I/O in Javascript - Reading ROOT files in a browser

CERN Multimedia

CERN. Geneva

2012-01-01

A JavaScript version of the ROOT I/O subsystem is being developed, in order to be able to browse (inspect) ROOT files in a platform independent way. This allows the content of ROOT files to be displayed in most web browsers, without having to install ROOT or any other software on the server or on the client. This gives a direct access to ROOT files from new (e.g. portable) devices in a light way. It will be possible to display simple graphical objects such as histograms and graphs (TH1, TH2, TH3, TProfile, TGraph, ...). The rendering will first be done with an external JavaScript graphic library, before investigating a way to produce graphics closer to what ROOT supports on other platforms (X11, Windows).

Hydrogen solubility in FLiNaK mixed with titanium powder

International Nuclear Information System (INIS)

Yagi, Juro; Sagara, Akio; Watanabe, Takashi; Tanaka, Teruya; Takayama, Sadatsugu; Muroga, Takeo

2015-01-01

Highlights: • The hydrogen solubility in a FLiNaK mixed with Ti powder was investigated. • A significant increase in hydrogen solubility was observed. • Controlling the purity of the molten salt was found to be one of the key issues. • A vanadium alloy would be compatible with the Ti powder/molten salt mixture. - Abstract: The hydrogen solubility in a FLiNaK molten salt mixed with Ti powder was investigated. A hydrogen-soluble metal powder mixed with a molten salt can increase the effective hydrogen solubility of the molten salt, which is currently a major disadvantage of molten salts. A significant increase in hydrogen solubility was observed, even with a mass fraction of Ti powder of only 0.1 wt%. The increase of hydrogen solubility was so large that a vanadium alloy would be compatible with the Ti powder/molten salt mixture, unlike typical molten salts that result in an unacceptably large tritium inventory in the vanadium alloy. In addition, contamination of the Ti powder by oxidation suppressed the hydrogen uptake and release capability. Controlling the purity of the molten salt was found to be one of the key issues for the metal powder mixture concept.

Moisture-induced caking of beverage powders.

Science.gov (United States)

Chávez Montes, Edgar; Santamaría, Nadia Ardila; Gumy, Jean-Claude; Marchal, Philippe

2011-11-01

Beverage powders can exhibit caking during storage due to high temperature and moisture conditions, leading to consumer dissatisfaction. Caking problems can be aggravated by the presence of sensitive ingredients. The caking behaviour of cocoa beverage powders, with varying amounts of a carbohydrate sensitive ingredient, as affected by climate conditions was studied in this work. Sorption isotherms of beverage powders were determined at water activities (a(w) ) ranging from 0.1 to 0.6 in a moisture sorption analyser by gravimetry and fitted to the Brunauer-Emmett-Teller (BET) or the Guggenheim-Anderson-de Boer (GAB) equation. Glass transition temperatures (T(g) ) at several a(w) were analysed by differential scanning calorimetry and fitted to the Gordon-Taylor equation. Deduced T(g) = f(a(w) ) functions helped to identify stability or caking zones. Specific experimental methods, based on the analysis of mechanical properties of powder cakes formed under compression, were used to quantify the degree of caking. Pantry tests complemented this study to put in evidence the visual perception of powder caking with increasing a(w) . The glass transition approach was useful to predict the risks of caking but was limited to products where T(g) can be measured. On the other hand, quantification of the caking degree by analysis of mechanical properties allowed estimation of the extent of degradation for each product. This work demonstrated that increasing amounts of a carbohydrate sensitive ingredient in cocoa beverages negatively affected their storage stability. Copyright © 2011 Society of Chemical Industry.

Powder metallurgy of turbine disc alloys

Energy Technology Data Exchange (ETDEWEB)

Ingesten, N.G. (Dep. of Engineering Metals)

1981-03-01

The first part embraced a study of carbide precipitated in IN 100 and astrology powders. The powder was heat treated at temperatures between 950/sup 0/C and 1150/sup 0/C. After aging at 950-1100/sup 0/C the MC-carbides formed during atomization were replaced by M/sub 23/C/sub 6/-carbides. After 1150/sup 0/C treatments the MC carbides were present again. Precipitation comparable with that obtained in HIP:ed specimens was not observed at free particle surfaces. However, powder particles which had agglomerated during atomization often exhibited considerable precipitation at contiguous surfaces. Obviously, contact between the particles must occur if coarse precipitation at particle surfaces is to develop. Reduced PPB-precipitation was obtained by pre-heat- treatment of powder before compaction. It is suggested that the carbon otherwise available for PPB-precipitation forms carbides in the interior of the powder particles. The aim of the second part was to ..gamma..-strengthen a Co-based super-alloy (Co-15Cr-3Mo-5Ti). Here the Ti-addition gives a coherent and ordered ..gamma..-phase Co/sub 3/Ti. However, upon ageing the alloy is unstable in order to increase the stability modifications of the alloy were prepared by: leaving out the Mo-content, adding 10 % Ni and by decreasing the Ti-content to 4.2 %. In addition, the effect of enhanced grain size and of deformation was investigated. Significant reduction of the transformation rate was only obtained by decresing the Ti-content while deformation of the alloy greatly increased the transformation rate.(author).

Sanitation of onion powder by irradiation and heating

Energy Technology Data Exchange (ETDEWEB)

Delkinova, S M [Bulgarplod, Plovdiv (Bulgaria); Dupuy, P [Institut National de Recherches Agronomiques (INRA), 21 - Dijon (France). Station de Recherches sur les Aliments de l' Homme

1973-01-01

Onion powder is frequently contaminated by a mesophile bacterial flora containing some spore-forming strains. Heating is not an admissible method of sterilization in this case, because of the volatile aromatic substances formed by the enzyme system present. After irradiation with 0.8 Mrad the surviving microbial flora contained Clostridium, Bacillus, Enterococcus and Micrococcus strains. These Micrococcus strains are less resistant than M.radiodurans and do not develop as spoilage organisms in foods. During the months following irradiation no growth was observed, on the contrary the number of cells surviving diminished in the same way both in the irradiated and the untreated samples. In soup powders with short cooking time, if the irradiated or untreated onion powder is added after boiling, a chance is caused by the growth of Lactobacillus or Bacillus strains. A radiation treatment with 0.4 Mrad gives a sterile soup, when boiled for 5 minutes. In meat pastes the most dangerous microbial flora is that consisting mainly of spora-forming anaerobic bacteria. It was shown that if the pasta was aromatized with onion powder treated with 0.2 Mrad before cooking, no growth occurred. The control sample containing untreated onion powder was spoiled by a microbial flora dominated by spore-forming aerobic bacteria. These two experiments proved that onion powder can be decontaminated by treatment with 0.2 or 0.4 Mrad. It is known that this dose has no detrimental effect on the organoleptic quality of the onion powder and the cost of irradiation is compatible with the price of the product treated. (F.J.)

Preparation of nanosize carbon powders by pulsed wire discharge

Energy Technology Data Exchange (ETDEWEB)

Minami, C.; Kinemuchi, Y.; Suzuki, T.; Suematsu, H.; Jiang, W.; Yatsui, K. [Nagaoka Univ. of Technology, Extreme Energy-Density Research Inst., Nagaoka, Niigata (Japan); Hirata, T.; Hatakeyama, R. [Tohoku Univ., Graduate School of Engineering, Sendai, Miyagi (Japan)

2002-06-01

Nanosize powders of carbons were tried to be synthesized by pulsed discharge of graphite wires in several kinds of ambient gases. When the wire was discharged in N{sub 2} gas, nanosize powders have been successfully produced. The result of X-ray diffraction analysis indicated that nanosize powders produced in N{sub 2} gas at 750 Torr were amorphous carbon containing glassy carbons, while mass-spectrum analysis demonstrated the production of fullerenes at 600 Torr. If the wire is discharged in Ar gas, dielectric breakdown takes place between electrodes, producing no carbon powders. (author)

Anatomic investigation of the lumbosacral nerve roots and dorsal root ganglia by MRI

International Nuclear Information System (INIS)

Hasegawa, Toru; Fuse, Kenzo; Mikawa, Yoshihiro; Watanabe, Ryo

1995-01-01

The morphology of the lumbosacral nerve roots and dorsal root ganglia (DRG) was examined by using magnetic resonance imaging (MRI) in 11 healthy male volunteers aged 20-40 years. One hundred and twenty-three nerve roots (15 at the L1 level, 22 each at the L2-L5 levels, and 20 at the S1 level) were examined in terms of the position and angle of the bifurcation of the nerve roots, length of the nerve root, and the position and width of DRG. The nerve roots at the lower levels showed more cephalad position and smaller angle of bifurcation on MRI. The distance from the bifurcation of nerve roots to the cephalad edge of DRG was significantly longer in the upper root levels and was significantly shorter in the L5 roots than the S1 roots. The positions of DRG at the S1 level tended to become cephalad. DRG that was positioned toward more caudal direction was larger and more elliptic. MRI provided useful information concerning morphology and anatomical position of nerve roots and DRG, thereby allowing accurate diagnosis and the determination of surgical indications. (N.K.)

Microstructural properties of electrochemically prepared Ni–Fe–W powders

International Nuclear Information System (INIS)

Ribić-Zelenović, L.; Ćirović, N.; Spasojević, M.; Mitrović, N.; Maričić, A.; Pavlović, V.

2012-01-01

A nanostructured Ni–Fe–W powder was obtained by electrodeposition from ammonium citrate electrolyte within the current density range of 500–1000 mA cm −2 at the electrolyte temperature of 50 °C–70 °C. XRD analysis shows that the powder contains an amorphous matrix having embedded nanocrystals of the FCC solid solution of iron and tungsten in nickel, with an average crystal grain size of 3.4 nm, a high internal microstrain value and a high density of chaotically distributed dislocations. EDS analysis exhibits that the chemical composition of the Ni–24%Fe–11%W powder does not depend upon current density and electrolyte temperature due to the diffusion control of the process of codeposition of nickel, iron and tungsten. SEM micrographs show that the electrodeposition results in the formation of two particle shapes: large cauliflower-like particles and small dendrite particles. The cauliflower-like particles contain deep cavities at hydrogen evolution sites. Cavity density increases with increasing deposition current density. Smaller powder particles are formed at higher temperatures and at higher current densities. During the first heating, relative magnetic permeability decreases reaching the Curie temperature at about 350 °C and after cooling exhibits a 12% increase due to the performed relaxation process. Following the second heating to 500 °C, the magnetic permeability of the powder is about 5% lower than that of the as-prepared powder due to crystallization of the amorphous phase of the powder and the crystal grain growth in FCC phase. - Highlights: ► Electrodeposition Ni–Fe–W powder from ammonium citrate electrolyte (500–1000 mA cm −2 ). ► Powder contains amorphous matrix and embedded nanocrystals 3.4 nm. ► Chemical composition Ni–24%Fe–11%W do not depend upon current density and electrolyte temperature. ► Two particle shapes: large cauliflower-like particles and small dendrite particles. ► Smaller powder particles are

Microstructural properties of electrochemically prepared Ni-Fe-W powders

Energy Technology Data Exchange (ETDEWEB)

Ribic-Zelenovic, L. [Faculty of Agronomy, University of Kragujevac, Cacak (Serbia); Cirovic, N. [Joint Laboratory for Advanced Materials of SASA, Technical Faculty Cacak, University of Kragujevac, Cacak (Serbia); Spasojevic, M. [Faculty of Agronomy, University of Kragujevac, Cacak (Serbia); Mitrovic, N., E-mail: nmitrov@tfc.kg.ac.rs [Joint Laboratory for Advanced Materials of SASA, Technical Faculty Cacak, University of Kragujevac, Cacak (Serbia); Maricic, A. [Joint Laboratory for Advanced Materials of SASA, Technical Faculty Cacak, University of Kragujevac, Cacak (Serbia); Pavlovic, V. [Faculty of Agriculture, University of Belgrade, Belgrade (Serbia)

2012-07-16

A nanostructured Ni-Fe-W powder was obtained by electrodeposition from ammonium citrate electrolyte within the current density range of 500-1000 mA cm{sup -2} at the electrolyte temperature of 50 Degree-Sign C-70 Degree-Sign C. XRD analysis shows that the powder contains an amorphous matrix having embedded nanocrystals of the FCC solid solution of iron and tungsten in nickel, with an average crystal grain size of 3.4 nm, a high internal microstrain value and a high density of chaotically distributed dislocations. EDS analysis exhibits that the chemical composition of the Ni-24%Fe-11%W powder does not depend upon current density and electrolyte temperature due to the diffusion control of the process of codeposition of nickel, iron and tungsten. SEM micrographs show that the electrodeposition results in the formation of two particle shapes: large cauliflower-like particles and small dendrite particles. The cauliflower-like particles contain deep cavities at hydrogen evolution sites. Cavity density increases with increasing deposition current density. Smaller powder particles are formed at higher temperatures and at higher current densities. During the first heating, relative magnetic permeability decreases reaching the Curie temperature at about 350 Degree-Sign C and after cooling exhibits a 12% increase due to the performed relaxation process. Following the second heating to 500 Degree-Sign C, the magnetic permeability of the powder is about 5% lower than that of the as-prepared powder due to crystallization of the amorphous phase of the powder and the crystal grain growth in FCC phase. - Highlights: Black-Right-Pointing-Pointer Electrodeposition Ni-Fe-W powder from ammonium citrate electrolyte (500-1000 mA cm{sup -2}). Black-Right-Pointing-Pointer Powder contains amorphous matrix and embedded nanocrystals 3.4 nm. Black-Right-Pointing-Pointer Chemical composition Ni-24%Fe-11%W do not depend upon current density and electrolyte temperature. Black

Solving Crystal Structures from Powder Diffraction Data

DEFF Research Database (Denmark)

Christensen, A. Nørlund; Lehmann, M. S.; Nielsen, Mogens

1985-01-01

High resolution powder data from both neutron and X-ray (synchrotron) sources have been used to estimate the possibility of direct structure determination from powder data. Two known structures were resolved by direct methods with neutron and X-ray data. With synchrotron X-ray data, the measured ...

The effect of reduced oxygen content powder on the impact toughness of 316 steel powder joined to 316 steel by low temperature HIP

International Nuclear Information System (INIS)

Lind, Anders; Sundstroem, Johan; Peacock, Alan

2005-01-01

During the manufacture of the blanket modules, 316L steel powder is simultaneously consolidated and joined to tubes and blocks of 316L materials by hot isostatic pressing (HIP). The high processing temperature can detrimentally increase the grain size of the water-cooling tubes in the structure and the blocks reducing their strength. It is well known [L. Arnberg, A. Karlsson, Influence of powder surface oxidation on some properties of a HIPed martensitic chromium steel, Int. J. Powder Metall. 24 (2) (1988) 107-112] that surface oxides on the powder particles negatively influence the impact toughness of material and joints consolidated in this way. At a high HIP temperature, the oxides are at least partly transformed, thereby improving the impact toughness [L. Nyborg, I. Olefjord, Surface analysis of PM martensitic steel before and after consolidation. Part 2. Surface analysis of compacted material, Powder Metall. 31 (1) (1988) 40-44]. In order to get acceptable mechanical properties of materials produced at a low HIP temperature, the oxygen content on the powder surfaces needs to be reduced. In order to study the effect of reducing the powder oxygen content, it was reduced and the results were compared to those of specimens with ordinary oxygen content. The effect on the impact toughness and the tensile strength of low temperature (1020 and 1060 deg. C) HIP joints between steel blocks and powder consolidated material with low and ordinary oxygen content was measured

Pharmaceutical powder compaction technology

National Research Council Canada - National Science Library

Çelik, Metin

2011-01-01

... through the compaction formulation process and application. Compaction of powder constituents both active ingredient and excipients is examined to ensure consistent and reproducible disintegration and dispersion profiles...

Micro-powder injection moulding of tungsten

International Nuclear Information System (INIS)

Zeep, B.

2007-12-01

For He-cooled Divertors as integral components of future fusion power plants, about 300000 complex shaped tungsten components are to be fabricated. Tungsten is the favoured material because of its excellent properties (high melting point, high hardness, high sputtering resistance, high thermal conductivity). However, the material's properties cause major problems for large scale production of complex shaped components. Due to the resistance of tungsten to mechanical machining, new fabrication technologies have to be developed. Powder injection moulding as a well established shaping technology for a large scale production of complex or even micro structured parts might be a suitable method to produce tungsten components for fusion applications but is not yet commercially available. The present thesis is dealing with the development of a powder injection moulding process for micro structured tungsten components. To develop a suitable feedstock, the powder particle properties, the binder formulation and the solid load were optimised. To meet the requirements for a replication of micro patterned cavities, a special target was to define the smallest powder particle size applicable for micro-powder injection moulding. To investigate the injection moulding performance of the developed feedstocks, experiments were successfully carried out applying diverse cavities with structural details in micro dimension. For debinding of the green bodies, a combination of solvent debinding and thermal debinding has been adopted for injection moulded tungsten components. To develop a suitable debinding strategy, a variation of the solvent debinding time, the heating rate and the binder formulation was performed. For investigating the thermal consolidation behaviour of tungsten components, sinter experiments were carried out applying tungsten powders suitable for micro-powder injection moulding. First mechanical tests of the sintered samples showed promising material properties such as a

An application of powder metallurgy to dentistry.

Science.gov (United States)

Oda, Y; Ueno, S; Kudoh, Y

1995-11-01

Generally, the dental casting method is used to fabricate dental prostheses made with metal. The method of fabricating dental prostheses from sintered titanium alloy has certain advantages: the elimination of casting defects, a sintering temperature that is lower than the melting point, and a shorter processing time. By examining (1) the properties of green, sintered compacts of titanium powder, (2) the effects of adding aluminum powder on the properties of green, sintered compacts of Ti-Al compound, and (3) the effects of adding copper powder on the properties of green, sintered compacts of Ti-Al-Cu compound, the authors developed a sintered titanium alloy on a trial basis. Because the properties satisfied the requirements of dental restorations, a powder metallurgical method of making dental restorations from this sintered titanium alloy was devised. Applications of such sintered titanium alloys for the metal coping of metal-ceramic crowns and denture base plates were discussed.

Ultrasonic assisted hot metal powder compaction.

Science.gov (United States)

Abedini, Rezvan; Abdullah, Amir; Alizadeh, Yunes

2017-09-01

Hot pressing of metal powders is used in production of parts with similar properties to wrought materials. During hot pressing processes, particle rearrangement, plastic deformation, creep, and diffusion are of the most effective powder densification mechanisms. Applying ultrasonic vibration is thought to result in great rates of densification and therefore higher efficiency of the process is expected. This paper deals with the effects of power ultrasonic on the densification of AA1100 aluminum powder under constant applied stress. The effects of particle size and process temperature on the densification behavior are discussed. The results show that applying ultrasonic vibration leads to an improved homogeneity and a higher relative density. Also, it is found that the effect of ultrasonic vibration is greater for finer particles. Copyright © 2016 Elsevier B.V. All rights reserved.

Method of solidifying powderous wastes

International Nuclear Information System (INIS)

Kakimoto, Akira; Miyake, Takashi; Sato, Shuichi; Inagaki, Yuzo.

1985-01-01

Purpose: To improve the properties of solidification products, in the case of solidifying powderous wastes with thermosetting resins. Method. A solvent for the solution of the thermosetting resin is admixed with the powderous wastes into a paste-like form prior to adding the resin to the wastes, which are then mixed with the resin solution. As the result, those solidification products having the specific gravity and the compression strength more excellent than those of the conventional ones, and much higher than the reference values can be obtained. (Kamimura, M.)

Operation whey powder. Anatomy of a German scandal

Energy Technology Data Exchange (ETDEWEB)

Brunner, E

1987-04-03

The odyssey of the contaminated whey powder finally has come to an end, and the 5000 tonnes of whey now are designated for decontamination by means of an ion exchange technique. The article throws light upon the political and economic reasons that sent the whey powder off on a chaotic journey. It is worth mentioning in this context that the natural radioactivity of inorganic fertilizers is much higher than that of the whey powder in question.

Exploring Oven-drying Technique in Producing Pineapple Powder

OpenAIRE

Cyril John A. Domingo; Wilma M. De Vera; Raquel C. Pambid

2017-01-01

Pineapple puree and juice of 11 to 12 °Brix were used to obtain pineapple powder using oven-drying technique. Addition of maltodextrin in treatments 2 and 4 yielded good quality powder, however addition of sugar and maltodextrin in treatments 1 and 3 resulted to sticky product which was processed to pineapple leather. Treatment 2 composed of pineapple puree and maltodextrin resulted to significantly higher powder recovery compared with treatment 4 which composed of pineapple juice...

Processing of tungsten csrap into powders by electroerosion dispersion

International Nuclear Information System (INIS)

Fominskij, L.P.; Myuller, A.S.; Levchuk, M.V.; Tarabrina, V.P.

1985-01-01

A powder produced by electroerosion dispersion in water from tungsten chips and rod cuttings is studied for its properties and structure. Powder particles are mainly of spherical shape, their predominant size is 2-4 μm. A fraction of -63 μm comprises a basic mass of the powder (up to 80%), an ultrafine (to 40 μm) phase of WO which is isolated by decantation comprises about 3.5% of its mass. The powder particles are low oxidized, have a fine-grain microstructure and consist of tungsten with admixture of β-W (to 30%). A fraction of total oxygen mass in the mixture of fractio s 0.74%. The powder containing less than 0.25% of oxygen is produced by decantation of the oxide phase. The product purity is determined exclusively by the purity of the raw material. Prior to producing articles it is recommended to anneal the powder either in the inert atmosphere or in the reduced medium at 750 deg C for β-W to transfer into common tungsten

Application of acid-modified Imperata cylindrica powder for latent fingerprint development.

Science.gov (United States)

Low, Wei Zeng; Khoo, Bee Ee; Aziz, Zalina Binti Abdul; Low, Ling Wei; Teng, Tjoon Tow; bin Abdullah, Ahmad Fahmi Lim

2015-09-01

A novel powdering material that utilizes acid-modified Imperata cylindrica (IC) powder for the development of fingermarks was studied. Experiments were carried out to determine the suitability, adherence quality and sensitivity of the acid-modified IC powder. Fingermarks of different constituents (eccrine, sebaceous and natural fingermarks) on different types of surfaces were used. Acid-modified IC powder was also used to develop fingermarks of different ages as well as aged fingermarks recovered from the water. From the visual inspection, acid-modified IC powder was able to interact with different fingermark constituents and produced distinct ridge details on the examined surfaces. It was also able to develop aged fingermarks and fingermarks that were submerged in water. A statistical comparison was made against the Sirchie® Hi-Fi black powder in terms of the powders' sensitivity and quality of the developed natural fingermarks. The image quality was analyzed using MITRE's Image Quality of Fingerprint (IQF) software. From the experiments, acid-modified IC powder has the potential as a fingermark development powder, although natural fingermarks developed by Sirchie® black powder showed better quality and sensitivity based on the results of the statistical comparison. Copyright © 2015 The Chartered Society of Forensic Sciences. Published by Elsevier Ireland Ltd. All rights reserved.

Submergence of Roots for Alveolar Bone Preservation. I. Endodontically Treated Roots.

Science.gov (United States)

1977-05-10

With Endodontic Submerged Roots Scale 0 1 2 3 Periapical 15 0 1 0 Pericoronal 7 3 3 3 (3 cysts ) = 1 _ _ _ _ _ _ _ _ _ = REFERENCES 1. Lam, R.: Contour...with coronal portions of the roots. These epithe lial-lined cysts prevented the formation of osteo- cementum over the coronal surface . In this study...the endodontically treated roots appeared to be primarily a response to the excess root cana l sealer that was expressed coronally and periapically

Influence of temperature and rooting-promoter on the formation of root-primodia and on the rooting of chrysanthemum cuttings under storage

International Nuclear Information System (INIS)

Nishio, J.; Fukuda, M.

1998-01-01

In order to promote rooting for direct planting cuttings in a lighting cultivation of chrysanthemum, we clarified the effects of light, temperature and term of storage of the cuttings, and analyzed ways of using rooting promoters as a pre-treatment of cuttings for root-primodia formation and rooting. Light as a pre-treatment had little effect, so it seemed to be not necessary for the formation of root primodia. The formation of the root-primodia was most hastened at 25 degrees C; inversely, it was slowed down at low temperatures, that is, the root-primodia were formed in four days at 25 degrees C, five days at 20 degrees C, and seven days at 15 degrees C. With the use of rooting promoters as a pre-treatment for the rooting of cuttings, the root-primodia were formed faster when the whole of cuttings were dipped in 40 mg/L solution of indelebutyric acid (IBA) than when the base of cuttings were dipped or sprayed 400 mg/L solution of IBA. It was appropriate that cuttings were dipped in IBA then put in in plastic-pots (7.5cm) vertically, packed in polyethylene-bags and stored in a corrugated carton box

Evaluating the Johanson theory for titanium powder

CSIR Research Space (South Africa)

Chikosha, S

2015-05-01

Full Text Available . In this study, the Johanson theory was used to determine the rolling parameters of titanium powder. Preliminary results of the nip angle, nip pressures and maximum horizontal pressures of the mill for the powder rolled on a 55mm diameter roll with roll gap sizes...

Resistance to compression of weakened roots subjected to different root reconstruction protocols

Directory of Open Access Journals (Sweden)

Lucas Villaça Zogheib

2011-12-01

Full Text Available OBJECTIVE: This study evaluated, in vitro, the fracture resistance of human non-vital teeth restored with different reconstruction protocols. MATERIAL AND METHODS: Forty human anterior roots of similar shape and dimensions were assigned to four groups (n=10, according to the root reconstruction protocol: Group I (control: non-weakened roots with glass fiber post; Group II: roots with composite resin by incremental technique and glass fiber post; Group III: roots with accessory glass fiber posts and glass fiber post; and Group IV: roots with anatomic glass fiber post technique. Following post cementation and core reconstruction, the roots were embedded in chemically activated acrylic resin and submitted to fracture resistance testing, with a compressive load at an angle of 45º in relation to the long axis of the root at a speed of 0.5 mm/min until fracture. All data were statistically analyzed with bilateral Dunnett's test (α=0.05. RESULTS: Group I presented higher mean values of fracture resistance when compared with the three experimental groups, which, in turn, presented similar resistance to fracture among each other. None of the techniques of root reconstruction with intraradicular posts improved root strength, and the incremental technique was suggested as being the most recommendable, since the type of fracture that occurred allowed the remaining dental structure to be repaired. CONCLUSION: The results of this in vitro study suggest that the healthy remaining radicular dentin is more important to increase fracture resistance than the root reconstruction protocol.

Living roots effect on 14C-labelled root litter decomposition

International Nuclear Information System (INIS)

Billes, G.; Bottner, P.

1981-01-01

Wheat was 14 C-labelled by cultivation on soil in pots, from seedling to maturity, in a chamber with constant CO 2 and 14 CO 2 levels. The 14 C-distribution was constant amongst the aerial parts, the roots and the soil in the whole pots. After cutting the plant tops, the pots were dried without disturbing the soil and root system. The pots were then incubated under controlled humidity and temperature conditions for 62 days. In the same time a second wheat cultivation was grown on one half of the pots in normal atmosphere without plant cultivation. The purpose of the work is to study the effect of living roots on decomposition of the former 14 C labelled roots litter. The CO 2 and the 14 CO 2 released from the soil were continuously measured. On incubation days 0, 18, 33 and 62, the remaining litter was separated from soil, and the organic matter was fractionated by repeated hydrolysis and NaOH extraction. Root litter disappeared faster when living roots were present than in bare soil. The accumulation and mineralization rates of humified components in soil followed two stages. While the roots of second wheat cultivation grew actively (until earing), the strong acid hydrolysable components accumulated in larger amount than in the case of bare soil. After earing, while roots activity was depressed, these components were partly mineralized and the 14 CO 2 release was then higher with plants than with bare soil. The humification and mineralization rate were related with living plant phenology stages. (orig.)

Custom-made, root-analogue direct laser metal forming implant: a case report.

Science.gov (United States)

Mangano, Francesco Guido; Cirotti, Bruno; Sammons, Rachel Lilian; Mangano, Carlo

2012-11-01

In the last few years, the application of digital technology in dentistry has become widespread with the introduction of cone beam computed tomography (CBCT) scan technology, and considerable progress has been made in the development of computer-aided design/ computer-aided manufacturing (CAD/CAM) techniques, including direct laser metal forming (DLMF). DLMF is a technology which allows solids with complex geometry to be produced by annealing metal powder microparticles in a focused laser beam, according to a computer-generated three-dimensional (3D) model. For dental implants, the fabrication process involves the laser-induced fusion of titanium microparticles, in order to build, layer by layer, the desired object. At present, the combined use of CBCT 3D data and CAD/CAM technology makes it possible to manufacture custom-made, root-analogue implants (RAI) with sufficient precision. This report demonstrates the successful clinical use of a custom-made, root-analogue DLMF implant. CBCT images of a non-restorable right maxillary first premolar were acquired and transformed into a 3D model. From this model, a custom-made, root-analogue DLMF implant was fabricated. Immediately after tooth extraction, the RAI with a pre-operatively designed abutment was placed in the extraction socket and restored with a single crown. At the 1-year follow-up examination, the RAI showed a good functional and aesthetic integration. The introduction of DLMF technology signals the start of a new revolutionary era for implant dentistry as its immense potential for producing highly complex macro- and microstructures is receiving vast interest in different medical fields.

Study of airborne particle generated by free falling powder

International Nuclear Information System (INIS)

Jacquelin, M.

2007-10-01

This study comes within the general framework of industrial facilities' safety research. Indeed, industrial processes, notably in the nuclear field, handle hazardous materials in powder form and can produce large quantities of fugitive dust. The study of the particles resuspension from powders is of interest of first order in order to estimate the consequences of this source term of contamination on the operator, the neighbouring installations and, if necessary, the environment. Up to now, there are very few reliable data in the scientific literature on the particulate emission in case of a scenario with an accidental free fall spill of powder. The powder dustiness evaluation is carried out using coefficients obtained in experiments, or using empirical correlations. The objective of the present work is to study the influence of some parameters involved in the airborne particles production by a free fall of powder. For that purpose, experiments are carried out in order to study the influence of parameters such as the type of discharge, the powder nature, the type of surface on which occurs the powder impaction, the system diameter used for discharge, and the falling mass. The results of mass fractions and number concentrations obtained highlighted the dominating parameters according to the type of discharge employed. Thereafter, the comparisons between our results and the empirical correlations available in the literature showed that those led to an undervaluation of the powder dustiness. This thus led us to develop, starting from the whole of experimental data, empirical correlations taking into account the various parameters studied as well as the interactions. (author)

Cellulose powder from Cladophora sp. algae.

Science.gov (United States)

Ek, R; Gustafsson, C; Nutt, A; Iversen, T; Nyström, C

1998-01-01

The surface are and crystallinity was measured on a cellulose powder made from Cladophora sp. algae. The algae cellulose powder was found to have a very high surface area (63.4 m2/g, N2 gas adsorption) and build up of cellulose with a high crystallinity (approximately 100%, solid state NMR). The high surface area was confirmed by calculations from atomic force microscope imaging of microfibrils from Cladophora sp. algae.

New automated pellet/powder assay system

International Nuclear Information System (INIS)

Olsen, R.N.

1975-01-01

This paper discusses an automated, high precision, pellet/ powder assay system. The system is an active assay system using a small isotopic neutron source and a coincidence detection system. The handling of the pellet powder samples has been automated and a programmable calculator has been integrated into the system to provide control and data analysis. The versatile system can assay uranium or plutonium in either active or passive modes

Powder bed charging during electron-beam additive manufacturing

International Nuclear Information System (INIS)

Cordero, Zachary C.; Meyer, Harry M.; Nandwana, Peeyush; Dehoff, Ryan R.

2017-01-01

Electrons injected into the build envelope during powder bed electron-beam additive manufacturing can accumulate on the irradiated particles and cause them to repel each other. Under certain conditions, these electrostatic forces can grow so large that they drive the particles out of the build envelope in a process known as “smoking”. In the present work, we investigate the causes of powder bed charging and smoking during electron-beam additive manufacturing. In the first part of the paper, we characterize the surface chemistry of a common feedstock material—gas-atomized Ti-6Al-4V powder—and find that a thick, electrically insulating oxide overlayer encapsulates the particles. Based on these experimental results, we then formulate an analytical model of powder bed charging in which each particle is approximated as a capacitor, where the particle and its substrate are the electrodes and the oxide overlayer is the dielectric. Using this model, we estimate the charge distribution in the powder bed, the electrostatic forces acting on the particles, and the conditions under which the powder bed will smoke. It is found that the electrical resistivity of the oxide overlayer strongly influences the charging behavior of the powder bed and that a high resistivity promotes charge accumulation and consequent smoking. This analysis suggests new quality control and process design measures that can help suppress smoking.

Ceramic grade (U,Pu)O2 powder fabrication

International Nuclear Information System (INIS)

Cristallini, O.A.; Villegas de Maroto, Marina; De Pino, J.I.; Osuna, H.A.

1980-01-01

Ceramic grade UO 2 powder was obtained by the homogeneous precipitation method. This procedure was afterwards applied to the fabrication of ceramic grade (U,Pu)O 2 powders, and mixed oxide powders with Pu content ranging from 0.7 to 16% were obtained. The obtainment of mixed ceramic oxides as well as the recuperation of fabrication scraps were developed in three steps: 1)study of the process of homogeneous precipitation of ammonium diuranate (ADU); 2) co-precipitation of ADU/PuO 2 .H 2 O for Pu concentrations of 0.6 and 6.8; 3) the thermal conditioning to mixed oxide (U,Pu)O 2 powders. The experimental procedure involves the following steps: preparation of the PuO 2 (NO 3 ) 4 solution; co-precipitation of the PuO 2 (NO 3 ) 2 solution with an UO 2 (NO 3 ) 2 solution; filtration and drying of the precipitate, thermal treatment and finally, mixing, pressing and sintering of the (U,Pu)O 2 and Nukem UO 2 powder with a 0. of zinc stearate. Different controls were made by means of physical, chemical and ceramographic tests. This method can be used for the fabrication of fast reactor fuels or, previous mechanical dispersion in UO 2 powder, for the fabrication of thermal reactors fuels. (M.E.L.) [es

HYDRATION PROCESS AND MECHANICAL PROPERTIES OF CEMENT PASTE WITH RECYCLED CONCRETE POWDER AND SILICA SAND POWDER

Directory of Open Access Journals (Sweden)

Jaroslav Topič

2017-11-01

Full Text Available Recycled concrete powder (RCP mostly consisting of cement paste could be reused as partial cement replacement. The aim of this paper is to compare hydration and mechanical properties of RCP and two types of silica sand powder (SSP. Comparison of those materials combined with cement can highlight the binder properties of recycled concrete powder. Using of two types of SSP also show an influence of their fines on hydration process and mechanical properties. Particle size analysis and calorimetric measurement were carried out and mechanical properties such as bulk density, dynamic Young’s modulus and compression strength were examine. Calorimetric measurement proves the presence of exposed non-hydrated particles in RCP that can react again. However lower density of old cement paste in RCP overweight the mentioned potential of RCP and mechanical properties are decreasing compared with reference cement paste and cement paste SSP.

Metal-Matrix Hardmetal/Cermet Reinforced Composite Powders for Thermal Spray

Directory of Open Access Journals (Sweden)

Dmitri GOLJANDIN

2012-03-01

Full Text Available Recycling of materials is becoming increasingly important as industry response to public demands, that resources must be preserved and environment protected. To produce materials competitive in cost with primary product, secondary producers have to pursue new technologies and other innovations. For these purposes different recycling technologies for composite materials (oxidation, milling, remelting etc are widely used. The current paper studies hardmetal/cermet powders produced by mechanical milling technology. The following composite materials were studied: Cr3C2-Ni cermets and WC-Co hardmetal. Different disintegrator milling systems for production of powders with determined size and shape were used. Chemical composition of produced powders was analysed.  To estimate the properties of recycled hardmetal/cermet powders, sieving analysis, laser granulometry and angularity study were conducted. To describe the angularity of milled powders, spike parameter–quadric fit (SPQ was used and experiments for determination of SPQ sensitivity and precision to characterize particles angularity were performed. Images used for calculating SPQ were taken by SEM processed with Omnimet Image Analyser 22. The graphs of grindability and angularity were composed. Composite powders based on Fe- and Ni-self-fluxing alloys for thermal spray (plasma and HVOF were produced. Technological properties of powders and properties of thermal sprayed coatings from studied powders were investigated. The properties of spray powders reinforced with recycled hardmetal and cermet particles as alternatives for cost-sensitive applications were demonstrated.DOI: http://dx.doi.org/10.5755/j01.ms.18.1.1348

Root resorption

DEFF Research Database (Denmark)

Kjaer, Inger

2014-01-01

Introduction: This paper summarizes the different conditions, which have a well-known influence on the resorption of tooth roots, exemplified by trauma and orthodontic treatment. The concept of the paper is to summarize and explain symptoms and signs of importance for avoiding resorption during...... orthodontic treatment. The Hypothesis: The hypothesis in this paper is that three different tissue layers covering the root in the so-called periroot sheet can explain signs and symptoms of importance for avoiding root resorption during orthodontic treatment. These different tissue layers are; outermost...... processes provoked by trauma and orthodontic pressure. Inflammatory reactions are followed by resorptive processes in the periroot sheet and along the root surface. Evaluation of the Hypothesis: Different morphologies in the dentition are signs of abnormal epithelium or an abnormal mesodermal layer. It has...

Zirconia powders production by precipitation: state-of-art review

International Nuclear Information System (INIS)

Oliveira, Ana Paula Almeida de; Torem, Mauricio Leonardo

1994-01-01

The important role played by zirconia in advanced ceramics can be attributed to its excellent wear and corrosion resistance and refractory character. The polymorphic nature of zirconia made the controlled addition of stabilizing oxides or the constraining effect of a dense ceramics matrix necessary to maintain high parameters had a significant influence on powder properties and on compacted powder behaviour in sintering. Particle shape and size, purity and crystalline structure were specially influenced by precipitation parameters. Therefore, this work presented a review of the state of the art in zirconia powder production and in the recent research on precipitation of that powder. (author)

Characterization of Cobalt F-75 powder for biomedical application

International Nuclear Information System (INIS)

Zuraidawani, C.D.; Shamsul, J.B.; Fazlul, B.; Nur Hidayah, A.Z.

2007-01-01

Cobalt F-75 alloys is commonly used for surgical implants because of their strength, corrosion resistance, non-magnetic behaviour and biocompatibility. In this paper, gas atomized of Cobalt F-75 powders were selected for evaluation. These powders supplied by Sandvik Osprey Ltd. The characteristics of these powders were investigated by using particle size analysis, X-ray Diffraction (XRD), X-ray Fluorescence (XRF) and Scanning Electron Microscope (SEM). Two different powder sizes (8.8 μm and 11.5 μm) have showed spherical morphology and the value of densities are 7.9 and 7.6 g/cm 3 respectively. (author)

Fine crystalline powders. Analysis of scientific and technical literature

International Nuclear Information System (INIS)

Denisenko, Eh.T.; Kulik, O.P.; Eremina, T.V.

1983-01-01

The state of development and studies of fine crystalline powders for recent five years is reviewed in the paper. Based on data available in literature, the most significant methods for fine metal and alloy powder production are considered and physicochemical properties of ultrafine particles are discussed from the standpoint of their interrelation with promising techniques for powder production. It is stated that the most important feature of ultrafine powder production technique at the present stage is a transition from the stage of data accumulation to that of controlled production of ultrafine structures of various metals and alloys under controllable conditions

Powder densification maps in Selective Laser Sintering

International Nuclear Information System (INIS)

Bourell, D.; Wohlert, M.; Harlan, N.; Beaman, J.; Das, S.

2002-01-01

Selective Laser Sintering (SLS) is a manufacturing process in which a part is produced without the need for part-specific tooling. It competes effectively with other manufacturing processes when part geometry is complex and the production run is not large. Traditionally, this was limited to prototype production, although tooling applications are now appearing. This paper describes several applications of powder densification maps to advance solutions in direct SLS of metallic and ceramic powders. Time-dependent plasticity issues arise in pre-processing of powder to make it suitable for SLS and in post-processing of SLS parts to obtain desired density. (Abstract Copyright [2002], Wiley Periodicals, Inc.)

Sinterability and microstructure evolution during sintering of ferrous powder mixtures

Directory of Open Access Journals (Sweden)

Kétner Bendo Demétrio

2013-01-01

Full Text Available The present work is focused on ferrous powder metallurgy and presents some results of a development of a suitable masteralloy for use as an additive to iron powder for the production of sintered steels. The masteralloy was produced by melting a powder mixture containing approximately Fe + 20% Ni + 20% Mn + 20% Si + 1% C (wt%, in order to obtain a cast billet that was converted into fine powder by crushing and milling. It was observed presence of SiC in the masteralloy after melting that is undesirable in the alloy. Si element should be introduced by using ferrosilicon. Sintered alloys with distinct contents of alloying elements were prepared by mixing the masteralloy powder to plain iron powder. Samples were produced by die compaction of the powder mixtures and sintering at 1200 °C in a differential dilatometer in order to record their linear dimensional behaviour during heating up and isothermal sintering, aiming at studying the sinterability of the compacts. Microstructure development during sintering was studied by SEM, XRD and microprobe analyses.

Gas-Phase Combustion Synthesis of Aluminum Nitride Powder

Science.gov (United States)

Axelbaum, R. L.; Lottes, C. R.; Huertas, J. I.; Rosen, L. J.

1996-01-01

Due to its combined properties of high electrical resistivity and high thermal conductivity aluminum nitride (AlN) is a highly desirable material for electronics applications. Methods are being sought for synthesis of unagglomerated, nanometer-sized powders of this material, prepared in such a way that they can be consolidated into solid compacts having minimal oxygen content. A procedure for synthesizing these powders through gas-phase combustion is described. This novel approach involves reacting AlCl3, NH3, and Na vapors. Equilibrium thermodynamic calculations show that 100% yields can be obtained for these reactants with the products being AlN, NaCl, and H2. The NaCl by-product is used to coat the AlN particles in situ. The coating allows for control of AlN agglomeration and protects the powders from hydrolysis during post-flame handling. On the basis of thermodynamic and kinetic considerations, two different approaches were employed to produce the powder, in co-flow diffusion flame configurations. In the first approach, the three reactants were supplied in separate streams. In the second, the AlCl3 and NH3 were premixed with HCl and then reacted with Na vapor. X-ray diffraction (XRD) spectra of as-produced powders show only NaCl for the first case and NaCl and AlN for the second. After annealing at 775 C tinder dynamic vacuum, the salt was removed and XRD spectra of powders from both approaches show only AlN. Aluminum metal was also produced in the co-flow flame by reacting AlCl3 with Na. XRD spectra of as-produced powders show the products to be only NaCl and elemental aluminum.

RESEARCH REGARDING THE CHEMICAL COMPOSITION OF POWDER MILK WITH NUTRIENTS

Directory of Open Access Journals (Sweden)

Liviu Giurgiulescu

2009-06-01

Full Text Available Powdered milk is a manufactured dairy product made by evaporating milk to dryness. This product has incomposition powder apple, powder carrots, rice flour and corn flour, vitamins, minerals.One purpose of drying milk is to preserve it; milk powder has a far longer self life than liquid milk and does notneed to be refrigerated, due to its low moisture content. Another purpose is to reduce its bulk for economy oftransportation. Milk powders contain all twenty standards amino acids and are high insoluble vitamins and minerals.The typical average amounts of major nutrients in the un reconstituted in 100 g milk are (by weight 12,7g protein,68,2g carbohydrates (predominantly lactose, calcium 427g , potassium g, vitamins11g, Inappropriate storageconditions (high relative humidity and high ambient temperature can significantly degrade the nutritive value ofmilk powder.

Synthesis of alumina powders by precipitation method and solvothermal treatment

International Nuclear Information System (INIS)

Politchuk, J.O.; Lima, N.B.; Lazar, D.R.R.; Ussui, V.; Yoshito, W.K.

2012-01-01

The improvement of alumina powders synthesis processes has been focused on the preparation of ceramic powders with well defined crystalline structure and with high specific surface area and nanometric particle size without formation of hard agglomerates. For this purpose the precipitation step should be studied and and also the temperature of alumina crystallization should be reduced. The aim of this study was to obtain alumina powders by hydroxide precipitation with ammonia in the presence of cationic surfactant, followed by solvothermal treatment and calcination. The powders were characterized by TG/DTA, X-ray diffraction, surface area measurements by gas adsorption (BET) and scanning electron microscopy. The results showed that powders produced by solvothermal treatment without surfactant have higher crystallinity. However the presence of CTAB enhances 240% the specific surface area compared with powders produced without this reagent (author)

Process for titanium powders spheroidization by RF induction plasma

International Nuclear Information System (INIS)

Gu Zhongtao; Ye Gaoying; Liu Chuandong; Tong Honghui

2010-01-01

Spherical titanium (Ti) particles were obtained by the process of heating irregularly shaped Ti powders under the radio frequency induction plasma (RF induction plasma) condition. The effect of feed rate, various dispersion methods and Ti particle size on the spheroidization efficiency was studied. The efficiency of the spheroidization is evaluated through the measurements of the percentage of powder spheroidized based on the electron microscopic observations and the tap density measurement of the processed powder. During the short flight of the particles in the plasma flow, of the order of a few milliseconds, the individual titanium particles of the powder are heated and melt, forming a spherical liquid droplet which upon freezing gives rise to the formation of a perfectly dense spherical solid particle. So RF induction plasma is a promising method for the preparation of spherical titanium powders with high flow ability. (authors)

Physcio chemical analysis of browning inhibitors treated solanum turberosum powder

International Nuclear Information System (INIS)

Alizai, M.N.K.; Abid, H.

2008-01-01

White potatoes (Solanum turberosum) were procured from agriculture Research Institute Tarnab Farm Peshawar to use for the preparation of potato powder. The process involves sorting. Washing, peeling slicing, blanching, treating with poly phenol oxidase inhibitors, dehydration, grinding and packing. All these parameters used in process were standardized. Chemical analysis of fresh potato and potato powder were carried out. Microbiological examination, functional properties and storage life studies of the potato powder were also performed. The product prepared by drying in cabinet dryer at 55 C for 7 hours was off white colour potatoes chips which was grinded to make off white potato powder. The potato powder possessed taste and texture. (author)

Measuring and Modeling Root Distribution and Root Reinforcement in Forested Slopes for Slope Stability Calculations

Science.gov (United States)

Cohen, D.; Giadrossich, F.; Schwarz, M.; Vergani, C.

2016-12-01

Roots provide mechanical anchorage and reinforcement of soils on slopes. Roots also modify soil hydrological properties (soil moisture content, pore-water pressure, preferential flow paths) via subsurface flow path associated with root architecture, root density, and root-size distribution. Interactions of root-soil mechanical and hydrological processes are an important control of shallow landslide initiation during rainfall events and slope stability. Knowledge of root-distribution and root strength are key components to estimate slope stability in vegetated slopes and for the management of protection forest in steep mountainous area. We present data that show the importance of measuring root strength directly in the field and present methods for these measurements. These data indicate that the tensile force mobilized in roots depends on root elongation (a function of soil displacement), root size, and on whether roots break in tension of slip out of the soil. Measurements indicate that large lateral roots that cross tension cracks at the scarp are important for slope stability calculations owing to their large tensional resistance. These roots are often overlooked and when included, their strength is overestimated because extrapolated from measurements on small roots. We present planned field experiments that will measure directly the force held by roots of different sizes during the triggering of a shallow landslide by rainfall. These field data are then used in a model of root reinforcement based on fiber-bundle concepts that span different spacial scales, from a single root to the stand scale, and different time scales, from timber harvest to root decay. This model computes the strength of root bundles in tension and in compression and their effect on soil strength. Up-scaled to the stand the model yields the distribution of root reinforcement as a function of tree density, distance from tree, tree species and age with the objective of providing quantitative

The tungsten powder study of the dispenser cathode

International Nuclear Information System (INIS)

Bao Jixiu; Wan Baofei

2006-01-01

The intercorrelation of tungsten powder properties, such as grain size, distribution and morphology, and porous matrix parameters with electron emission capability and longevity of Ba dispenser cathodes has been investigated for the different grain morphologies. It is shown that a fully cleaning step of the tungsten powder is so necessary that the tungsten powder will be reduction of oxide in hydrogen atmosphere above 700 deg. C. The porosity of the tungsten matrix distributes more even and the closed pore is fewer, the average granule size of the tungsten powder distributes more convergent. The porosity of the tungsten matrix and the evaporation of the activator are bigger and the pulse of the cathode is smaller when the granularity is bigger by the analysis of the electronic microscope and diode experiment

The tungsten powder study of the dispenser cathode

Science.gov (United States)

Bao, Ji-xiu; Wan, Bao-fei

2006-06-01

The intercorrelation of tungsten powder properties, such as grain size, distribution and morphology, and porous matrix parameters with electron emission capability and longevity of Ba dispenser cathodes has been investigated for the different grain morphologies. It is shown that a fully cleaning step of the tungsten powder is so necessary that the tungsten powder will be reduction of oxide in hydrogen atmosphere above 700 °C. The porosity of the tungsten matrix distributes more even and the closed pore is fewer, the average granule size of the tungsten powder distributes more convergent. The porosity of the tungsten matrix and the evaporation of the activator are bigger and the pulse of the cathode is smaller when the granularity is bigger by the analysis of the electronic microscope and diode experiment.

Antioxidant Properties of Berberis aetnensis C. Presl (Berberidaceae Roots Extract and Protective Effects on Astroglial Cell Cultures

Directory of Open Access Journals (Sweden)

Agata Campisi

2014-01-01

Full Text Available Berberis aetnensis C. Presl (Berberidaceae is a bushy-spiny shrub common on Mount Etna (Sicily. We demonstrated that the alkaloid extract of roots of B. aetnensis C. Presl contains prevalently berberine and berbamine, possesses antimicrobial properties, and was able to counteract the upregulation evoked by glutamate of tissue transglutaminase in primary rat astroglial cell cultures. Until now, there are no reports regarding antioxidant properties of B. aetnensis C. Presl collected in Sicily. Air-dried, powdered roots of B. aetnensis C. Presl were extracted, identified, and quantified by HPLC. We assessed in cellular free system its effect on superoxide anion, radicals scavenging activity of antioxidants against free radicals like the 1,1-diphenyl-2-picrylhydrazyl radical, and the inhibition of xanthine oxidase activity. In primary rat astroglial cell cultures, exposed to glutamate, we evaluated the effect of the extract on glutathione levels and on intracellular production of reactive oxygen species generated by glutamate. The alkaloid extract of B. aetnensis C. Presl inhibited superoxide anion, restored to control values, the decrease of GSH levels, and the production of reactive oxygen species. Potent antioxidant activities of the alkaloid extract of roots of B. aetnensis C. Presl may be one of the mechanisms by which the extract is effective against health disorders associated to oxidative stress.

Antioxidant properties of Berberis aetnensis C. Presl (Berberidaceae) roots extract and protective effects on astroglial cell cultures.

Science.gov (United States)

Campisi, Agata; Acquaviva, Rosaria; Bonfanti, Roberta; Raciti, Giuseppina; Amodeo, Andrea; Mastrojeni, Silvana; Ragusa, Salvatore; Iauk, Liliana

2014-01-01

Berberis aetnensis C. Presl (Berberidaceae) is a bushy-spiny shrub common on Mount Etna (Sicily). We demonstrated that the alkaloid extract of roots of B. aetnensis C. Presl contains prevalently berberine and berbamine, possesses antimicrobial properties, and was able to counteract the upregulation evoked by glutamate of tissue transglutaminase in primary rat astroglial cell cultures. Until now, there are no reports regarding antioxidant properties of B. aetnensis C. Presl collected in Sicily. Air-dried, powdered roots of B. aetnensis C. Presl were extracted, identified, and quantified by HPLC. We assessed in cellular free system its effect on superoxide anion, radicals scavenging activity of antioxidants against free radicals like the 1,1-diphenyl-2-picrylhydrazyl radical, and the inhibition of xanthine oxidase activity. In primary rat astroglial cell cultures, exposed to glutamate, we evaluated the effect of the extract on glutathione levels and on intracellular production of reactive oxygen species generated by glutamate. The alkaloid extract of B. aetnensis C. Presl inhibited superoxide anion, restored to control values, the decrease of GSH levels, and the production of reactive oxygen species. Potent antioxidant activities of the alkaloid extract of roots of B. aetnensis C. Presl may be one of the mechanisms by which the extract is effective against health disorders associated to oxidative stress.

Rooting depth and root depth distribution of Trifolium repens × T. uniflorum interspecific hybrids.

Science.gov (United States)

Nichols, S N; Hofmann, R W; Williams, W M; van Koten, C

2016-05-20

Traits related to root depth distribution were examined in Trifolium repens × T. uniflorum backcross 1 (BC 1 ) hybrids to determine whether root characteristics of white clover could be improved by interspecific hybridization. Two white clover cultivars, two T. uniflorum accessions and two BC 1 populations were grown in 1 -m deep tubes of sand culture. Maximum rooting depth and root mass distribution were measured at four harvests over time, and root distribution data were fitted with a regression model to provide measures of root system shape. Morphological traits were measured at two depths at harvest 3. Root system shape of the hybrids was more similar to T. uniflorum than to white clover. The hybrids and T. uniflorum had a higher rate of decrease in root mass with depth than white clover, which would result in higher proportions of root mass in the upper profile. Percentage total root mass at 100-200 mm depth was higher for T. uniflorum than white clover, and for Crusader BC 1 than 'Crusader'. Roots of the hybrids and T. uniflorum also penetrated deeper than those of white clover. T. uniflorum had thicker roots at 50-100 mm deep than the other entries, and more of its fine root mass at 400-500 mm. The hybrids and white clover had more of their fine root mass higher in the profile. Consequently, T. uniflorum had a higher root length density at 400-500 mm than most entries, and a smaller decrease in root length density with depth. These results demonstrate that rooting characteristics of white clover can be altered by hybridization with T. uniflorum, potentially improving water and nutrient acquisition and drought resistance. Root traits of T. uniflorum are likely to be adaptations to soil moisture and fertility in its natural environment. © The Author 2016. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Comparative toxicity of four local botanical powders to Sitophilus ...

African Journals Online (AJOL)

Maize grains were admixed with the powders at the rates0, 5, 10, 20 and 40 g/kg for the assessment of mortality over a 14-d or 30-d period, as well as for population increase and damage. Within 14-d exposure, P. glandulosus powder caused the highest weevil mortality followed by A. indica. A. indica powder was by far ...

Synthesis and characterization of nanoboron powders prepared with ...

Indian Academy of Sciences (India)

mechanochemical reaction between B2O3 and Mg powders ... Malek—Ashtar University of Technology, School of Chemistry and Chemical Engineering, Tehran, P.O. Box .... powders and chemical reaction takes place at the interface of.

Modeling of microwave heating of metallic powders

International Nuclear Information System (INIS)

Buchelnikov, V.D.; Louzguine-Luzgin, D.V.; Anzulevich, A.P.; Bychkov, I.V.; Yoshikawa, N.; Sato, M.; Inoue, A.

2008-01-01

As it is known from the experiment that bulk metallic samples reflect microwaves while powdered samples can absorb such a radiation and be heated efficiently. In the present paper we investigate theoretically the mechanisms of penetration of a layer of metallic powder by microwave radiation and microwave heating of such a system