MIDAS/PK code development using point kinetics model

International Nuclear Information System (INIS)

Song, Y. M.; Park, S. H.

1999-01-01

In this study, a MIDAS/PK code has been developed for analyzing the ATWS (Anticipated Transients Without Scram) which can be one of severe accident initiating events. The MIDAS is an integrated computer code based on the MELCOR code to develop a severe accident risk reduction strategy by Korea Atomic Energy Research Institute. In the mean time, the Chexal-Layman correlation in the current MELCOR, which was developed under a BWR condition, is appeared to be inappropriate for a PWR. So as to provide ATWS analysis capability to the MIDAS code, a point kinetics module, PKINETIC, has first been developed as a stand-alone code whose reference model was selected from the current accident analysis codes. In the next step, the MIDAS/PK code has been developed via coupling PKINETIC with the MIDAS code by inter-connecting several thermal hydraulic parameters between the two codes. Since the major concern in the ATWS analysis is the primary peak pressure during the early few minutes into the accident, the peak pressure from the PKINETIC module and the MIDAS/PK are compared with the RETRAN calculations showing a good agreement between them. The MIDAS/PK code is considered to be valuable for analyzing the plant response during ATWS deterministically, especially for the early domestic Westinghouse plants which rely on the operator procedure instead of an AMSAC (ATWS Mitigating System Actuation Circuitry) against ATWS. This capability of ATWS analysis is also important from the view point of accident management and mitigation

Accident consequence assessment code development

International Nuclear Information System (INIS)

Homma, T.; Togawa, O.

1991-01-01

This paper describes the new computer code system, OSCAAR developed for off-site consequence assessment of a potential nuclear accident. OSCAAR consists of several modules which have modeling capabilities in atmospheric transport, foodchain transport, dosimetry, emergency response and radiological health effects. The major modules of the consequence assessment code are described, highlighting the validation and verification of the models. (author)

Development of MCNP interface code in HFETR

International Nuclear Information System (INIS)

Qiu Liqing; Fu Rong; Deng Caiyu

2007-01-01

In order to describe the HFETR core with MCNP method, the interface code MCNPIP for HFETR and MCNP code is developed. This paper introduces the core DXSY and flowchart of MCNPIP code, and the handling of compositions of fuel elements and requirements on hardware and software. Finally, MCNPIP code is validated against the practical application. (authors)

Development of realistic thermal hydraulic system analysis code

Energy Technology Data Exchange (ETDEWEB)

Lee, Won Jae; Chung, B. D; Kim, K. D. [and others

2002-05-01

The realistic safety analysis system is essential for nuclear safety research, advanced reactor development, safety analysis in nuclear industry and 'in-house' plant design capability development. In this project, we have developed a best-estimate multi-dimensional thermal-hydraulic system code, MARS, which is based on the integrated version of the RELAP5 and COBRA-TF codes. To improve the realistic analysis capability, we have improved the models for multi-dimensional two-phase flow phenomena and for advanced two-phase flow modeling. In addition, the GUI (Graphic User Interface) feature were developed to enhance the user's convenience. To develop the coupled analysis capability, the MARS code were linked with the three-dimensional reactor kinetics code (MASTER), the core thermal analysis code (COBRA-III/CP), and the best-estimate containment analysis code (CONTEMPT), resulting in MARS/MASTER/COBRA/CONTEMPT. Currently, the MARS code system has been distributed to 18 domestic organizations, including research, industrial, regulatory organizations and universities. The MARS has been being widely used for the safety research of existing PWRs, advanced PWR, CANDU and research reactor, the pre-test analysis of TH experiments, and others.

Development of realistic thermal hydraulic system analysis code

International Nuclear Information System (INIS)

Lee, Won Jae; Chung, B. D; Kim, K. D.

2002-05-01

The realistic safety analysis system is essential for nuclear safety research, advanced reactor development, safety analysis in nuclear industry and 'in-house' plant design capability development. In this project, we have developed a best-estimate multi-dimensional thermal-hydraulic system code, MARS, which is based on the integrated version of the RELAP5 and COBRA-TF codes. To improve the realistic analysis capability, we have improved the models for multi-dimensional two-phase flow phenomena and for advanced two-phase flow modeling. In addition, the GUI (Graphic User Interface) feature were developed to enhance the user's convenience. To develop the coupled analysis capability, the MARS code were linked with the three-dimensional reactor kinetics code (MASTER), the core thermal analysis code (COBRA-III/CP), and the best-estimate containment analysis code (CONTEMPT), resulting in MARS/MASTER/COBRA/CONTEMPT. Currently, the MARS code system has been distributed to 18 domestic organizations, including research, industrial, regulatory organizations and universities. The MARS has been being widely used for the safety research of existing PWRs, advanced PWR, CANDU and research reactor, the pre-test analysis of TH experiments, and others

Development of a nuclear power plant system analysis code

International Nuclear Information System (INIS)

Sim, Suk K.; Jeong, J. J.; Ha, K. S.; Moon, S. K.; Park, J. W.; Yang, S. K.; Song, C. H.; Chun, S. Y.; Kim, H. C.; Chung, B. D.; Lee, W. J.; Kwon, T. S.

1997-07-01

During the period of this study, TASS 1.0 code has been prepared for the non-LOCA licensing and reload safety analyses of the Westinghouse and the Korean Standard Nuclear Power Plants (KSNPP) type reactors operating in Korea. TASS-NPA also has been developed for a real time simulation of the Kori-3/4 transients using on-line graphical interactions. TASS 2.0 code has been further developed to timely apply the TASS 2.0 code for the design certification of the KNGR. The COBRA/RELAP5 code, a multi-dimensional best estimate system code, has been developed by integrating the realistic three-dimensional reactor vessel model with the RELAP5 /MOD3.2 code, a one-dimensional system code. Also, a 3D turbulent two-phase flow analysis code, FEMOTH-TF, has been developed using finite element technique to analyze local thermal hydraulic phenomena in support of the detailed design analysis for the development of the advanced reactors. (author). 84 refs., 27 tabs., 83 figs

COSINE software development based on code generation technology

International Nuclear Information System (INIS)

Ren Hao; Mo Wentao; Liu Shuo; Zhao Guang

2013-01-01

The code generation technology can significantly improve the quality and productivity of software development and reduce software development risk. At present, the code generator is usually based on UML model-driven technology, which can not satisfy the development demand of nuclear power calculation software. The feature of scientific computing program was analyzed and the FORTRAN code generator (FCG) based on C# was developed in this paper. FCG can generate module variable definition FORTRAN code automatically according to input metadata. FCG also can generate memory allocation interface for dynamic variables as well as data access interface. FCG was applied to the core and system integrated engine for design and analysis (COSINE) software development. The result shows that FCG can greatly improve the development efficiency of nuclear power calculation software, and reduce the defect rate of software development. (authors)

Development and application of the waste code

International Nuclear Information System (INIS)

Morison, I.W.

1984-01-01

This paper discusses the objectives and general approach underlying the Australian Code of Practice on the Management of Radioactive Wastes arising from the Mining and Milling of Radioactive Ores 1982. Background to the development of the Code is provided and the guidelines which supplement the Code are considered

Health Code Number (HCN) Development Procedure

Energy Technology Data Exchange (ETDEWEB)

Petrocchi, Rocky; Craig, Douglas K.; Bond, Jayne-Anne; Trott, Donna M.; Yu, Xiao-Ying

2013-09-01

This report provides the detailed description of health code numbers (HCNs) and the procedure of how each HCN is assigned. It contains many guidelines and rationales of HCNs. HCNs are used in the chemical mixture methodology (CMM), a method recommended by the department of energy (DOE) for assessing health effects as a result of exposures to airborne aerosols in an emergency. The procedure is a useful tool for proficient HCN code developers. Intense training and quality assurance with qualified HCN developers are required before an individual comprehends the procedure to develop HCNs for DOE.

SCDAP/RELAP5/MOD3 code development

International Nuclear Information System (INIS)

Allison, C.M.; Siefken, J.L.; Coryell, E.W.

1992-01-01

The SCOAP/RELAP5/MOD3 computer code is designed to describe the overall reactor coolant system (RCS) thermal-hydraulic response, core damage progression, and fission product release and transport during severe accidents. The code is being developed at the Idaho National Engineering Laboratory (INEL) under the primary sponsorship of the Office of Nuclear Regulatory Research of the US Nuclear Regulatory Commission (NRC). Code development activities are currently focused on three main areas - (a) code usability, (b) early phase melt progression model improvements, and (c) advanced reactor thermal-hydraulic model extensions. This paper describes the first two activities. A companion paper describes the advanced reactor model improvements being performed under RELAP5/MOD3 funding

Development of the DTNTES code

International Nuclear Information System (INIS)

Ortega Prieto, P.; Morales Dorado, M.D.; Alonso Santos, A.

1987-01-01

The DTNTES code has been developed in the Department of Nuclear Technology of the Polytechnical University in Madrid as a part of the Research Program on Quantitative Risk Analysis. DTNTES code calculates several time-dependent probabilistic characteristics of basic events, minimal cut sets and the top event of a fault tree. The code assumes that basic events are statistically independent, and they have failure and repair distributions. It computes the minimal cut upper bound approach for the top event unavailability, and the time-dependent unreliability of the top event by means of different methods, selected by the user. These methods are: expected number of system failures, failure rate, Barlow-Proschan bound, steady-state upper bound, and T* method. (author)

Development of an Auto-Validation Program for MARS Code Assessments

International Nuclear Information System (INIS)

Lee, Young Jin; Chung, Bub Dong

2006-01-01

MARS (Multi-dimensional Analysis of Reactor Safety) code is a best-estimate thermal hydraulic system analysis code developed at KAERI. It is important for a thermal hydraulic computer code to be assessed against theoretical and experimental data to verify and validate the performance and the integrity of the structure, models and correlations of the code. The code assessment efforts for complex thermal hydraulics code such as MARS code can be tedious, time-consuming and require large amount of human intervention in data transfer to see the results in graphic forms. Code developers produce many versions of a code during development and each version need to be verified for integrity. Thus, for MARS code developers, it is desirable to have an automatic way of carrying out the code assessment calculations. In the present work, an Auto-Validation program that carries out the code assessment efforts has been developed. The program uses the user supplied configuration file (with '.vv' extension) which contain commands to read input file, to execute the user selected MARS program, and to generate result graphs. The program can be useful if a same set of code assessments is repeated with different versions of the code. The program is written with the Delphi program language. The program runs under the Microsoft Windows environment

Optics code development at Los Alamos

International Nuclear Information System (INIS)

Mottershead, C.T.; Lysenko, W.P.

1988-01-01

This paper is an overview of part of the beam optics code development effort in the Accelerator Technology Division at Los Alamos National Laboratory. The aim of this effort is to improve our capability to design advanced beam optics systems. The work reported is being carried out by a collaboration of permanent staff members, visiting consultants, and student research assistants. The main components of the effort are: building a new framework of common supporting utilities and software tools to facilitate further development; research and development on basic computational techniques in classical mechanics and electrodynamics; and evaluation and comparison of existing beam optics codes, and support for their continuing development. 17 refs

Optics code development at Los Alamos

International Nuclear Information System (INIS)

Mottershead, C.T.; Lysenko, W.P.

1988-01-01

This paper is an overview of part of the beam optics code development effort in the Accelerator Technology Division at Los Alamos National Laboratory. The aim of this effort is to improve our capability to design advanced beam optics systems. The work reported is being carried out by a collaboration of permanent staff members, visiting consultants, and student research assistants. The main components of the effort are building a new framework of common supporting utilities and software tools to facilitate further development. research and development on basic computational techniques in classical mechanics and electrodynamics, and evaluation and comparison of existing beam optics codes, and support for their continuing development

Subchannel analysis code development for CANDU fuel channel

International Nuclear Information System (INIS)

Park, J. H.; Suk, H. C.; Jun, J. S.; Oh, D. J.; Hwang, D. H.; Yoo, Y. J.

1998-07-01

Since there are several subchannel codes such as COBRA and TORC codes for a PWR fuel channel but not for a CANDU fuel channel in our country, the subchannel analysis code for a CANDU fuel channel was developed for the prediction of flow conditions on the subchannels, for the accurate assessment of the thermal margin, the effect of appendages, and radial/axial power profile of fuel bundles on flow conditions and CHF and so on. In order to develop the subchannel analysis code for a CANDU fuel channel, subchannel analysis methodology and its applicability/pertinence for a fuel channel were reviewed from the CANDU fuel channel point of view. Several thermalhydraulic and numerical models for the subchannel analysis on a CANDU fuel channel were developed. The experimental data of the CANDU fuel channel were collected, analyzed and used for validation of a subchannel analysis code developed in this work. (author). 11 refs., 3 tabs., 50 figs

Developments of fuel performance analysis codes in KEPCO NF

International Nuclear Information System (INIS)

Han, H. T.; Choi, J. M.; Jung, C. D.; Yoo, J. S.

2012-01-01

The KEPCO NF has developed fuel performance analysis and design code named as ROPER, and utility codes of XGCOL and XDNB in order to perform fuel rod design evaluation for Korean nuclear power plants. The ROPER code intends to cover full range of fuel performance evaluation. The XGCOL code is for the clad flattening evaluation and the XDNB code is for the extensive DNB propagation evaluation. In addition to these, the KEPCO NF is now in the developing stage for 3-dimensional fuel performance analysis code, named as OPER3D, using 3-dimensional FEM for the nest generation within the joint project CANDU ENERGY in order to analyze PCMI behavior and fuel performance under load following operation. Of these, the ROPER code is now in the stage of licensing activities by Korean regulatory body and the other two are almost in the final developing stage. After finishing the developing, licensing activities are to be performed. These activities are intending to acquire competitiveness, originality, vendor-free ownership of fuel performance codes in the KEPCO NF

Development of computer code in PNC, 3

International Nuclear Information System (INIS)

Ohtaki, Akira; Ohira, Hiroaki

1990-01-01

Super-COPD, a code which is integrated by calculation modules, has been developed in order to evaluate kinds of dynamics of LMFBR plant by improving COPD. The code involves all models and its advanced models of COPD in module structures. The code makes it possible to simulate the system dynamics of LMFBR plant of any configurations and components. (author)

NASA space radiation transport code development consortium

International Nuclear Information System (INIS)

Townsend, L. W.

2005-01-01

Recently, NASA established a consortium involving the Univ. of Tennessee (lead institution), the Univ. of Houston, Roanoke College and various government and national laboratories, to accelerate the development of a standard set of radiation transport computer codes for NASA human exploration applications. This effort involves further improvements of the Monte Carlo codes HETC and FLUKA and the deterministic code HZETRN, including developing nuclear reaction databases necessary to extend the Monte Carlo codes to carry out heavy ion transport, and extending HZETRN to three dimensions. The improved codes will be validated by comparing predictions with measured laboratory transport data, provided by an experimental measurements consortium, and measurements in the upper atmosphere on the balloon-borne Deep Space Test Bed (DSTB). In this paper, we present an overview of the consortium members and the current status and future plans of consortium efforts to meet the research goals and objectives of this extensive undertaking. (authors)

Development of thermal hydraulic evaluation code for CANDU reactors

International Nuclear Information System (INIS)

Kim, Man Woong; Yu, Seon Oh; Choi, Yong Seog; Shin, Chull; Hwang, Soo Hyun

2004-02-01

To enhance the safety of operating CANDU reactors, the establishment of the safety analysis codes system for CANDU reactors is in progress. As for the development of thermal-hydraulic analysis code for CANDU system, the studies for improvement of evaluation model inside RELAP/CANDU code and the development of safety assessment methodology for GSI (Generic Safety Issues) are in progress as a part of establishment of CANDU safety assessment system. To develop the 3-D thermal-hydraulic analysis code for moderator system, the CFD models for analyzing the CANDU-6 moderator circulation are developed. One model uses a structured grid system with the porous media approach for the 380 Calandria tubes in the core region. The other uses a unstructured grid system on the real geometry of 380 Calandria tubes, so that the detailed fluid flow between the Calandria tubes can be observed. As to the development of thermal-hydraulic analysis code for containment, the study on the applicability of CONTAIN 2.0 code to a CANDU containment was conducted and a simulation of the thermal-hydraulic phenomena during the accident was performed. Besides, the model comparison of ESFs (Engineered Safety Features) inside CONTAIN 2.0 code and PRESCON code has also conducted

ICARE/CATHARE and ASTEC code development trends

International Nuclear Information System (INIS)

Chatelard, P.; Dorsselaere, J.-P. van

2000-01-01

Regarding the computer code development for simulation of LWR severe accidents, IPSN developed a two-tier approach based on detailed codes such as ICARE/CATHARE and simplified models to be assembled in the ASTEC integral code. The ICARE/CATHARE code results from the coupling between the ICARE2 code modelling the core degradation phenomena and the thermalhydraulics code CATHARE2. It allows to calculate PWR and VVER severe accident sequences in the whole RCS. The modelling of the early degradation phase can be considered as rather complete in the ICARE/CATHARE V1 mod1 version (to be released by mid-2000) whereas some models are still missing for the late phase. The main future developments (ICARE/CATHARE V2) will concern the multi-dimensional thermalhydraulics, the quenching of partially damaged cores (mechanical and chemical effects), the debris bed two-phase thermalhydraulics (including reflooding) and the corium behaviour in the lower head. The main other physical improvements should concern the behaviour of boron carbide control rods, the processes governing the core loss of geometry (transition phase) and the oxidation of relocated melts. The ASTEC (Accident Source Term Evaluation Code) integral code, commonly developed by IPSN and GRS, aims to predict an entire LWR (PWR, VVER and BWR) severe accident sequence from the initiating event through to FP release out of the containment, for source term, PSA level 2, or accident management studies. The version ASTEC VO.3 to be released by mid-2000 can be considered now as robust and fast-running enough (between 2 and 12 hours for a one day accident) and allows to perform, with a containment multi-compartment configuration, any scenario accident study accounting for the main safety systems and operator procedures (spray, recombiner, etc.). The next version ASTEC V1, to be released beginning of 2002, will include the frontend simulation and improve modelling of in-vessel core degradation. A large validation activity will

Aeroelastic code development activities in the United States

Energy Technology Data Exchange (ETDEWEB)

Wright, A.D. [National Renewable Energy Lab., Golden, Colorado (United States)

1996-09-01

Designing wind turbines to be fatigue resistant and to have long lifetimes at minimal cost is a major goal of the federal wind program and the wind industry in the United States. To achieve this goal, we must be able to predict critical loads for a wide variety of different wind turbines operating under extreme conditions. The codes used for wind turbine dynamic analysis must be able to analyze a wide range of different wind turbine configurations as well as rapidly predict the loads due to turbulent wind inflow with a minimal set of degrees of freedom. Code development activities in the US have taken a two-pronged approach in order to satisfy both of these criteria: (1) development of a multi-purpose code which can be used to analyze a wide variety of wind turbine configurations without having to develop new equations of motion with each configuration change, and (2) development of specialized codes with minimal sets of specific degrees of freedom for analysis of two- and three-bladed horizontal axis wind turbines and calculation of machine loads due to turbulent inflow. In the first method we have adapted a commercial multi-body dynamics simulation package for wind turbine analysis. In the second approach we are developing specialized codes with limited degrees of freedom, usually specified in the modal domain. This paper will summarize progress to date in the development, validation, and application of these codes. (au) 13 refs.

Monte Carlo code development in Los Alamos

International Nuclear Information System (INIS)

Carter, L.L.; Cashwell, E.D.; Everett, C.J.; Forest, C.A.; Schrandt, R.G.; Taylor, W.M.; Thompson, W.L.; Turner, G.D.

1974-01-01

The present status of Monte Carlo code development at Los Alamos Scientific Laboratory is discussed. A brief summary is given of several of the most important neutron, photon, and electron transport codes. 17 references. (U.S.)

Developing an Australian code of construction ethics

Directory of Open Access Journals (Sweden)

Sean Francis McCarthy

2012-05-01

Full Text Available This article looks at the increasing need to consider the role of ethics in construction. The industry, historically, has been challenged by allegations of a serious shortfall in ethical standards. Only limited attempts to date in Australia have been made to address that concern. Any ethical analysis should consider the definition of ethics and its historical development. This paper considers major historical developments in ethical thinking as well as contemporary thinking on ethics for professional sub-sets. A code could be developed specific to construction. Current methods of addressing ethics in construction and in other industries are also reviewed. This paper argues that developing a code of ethics, supported by other measures is the way forward. The author’s aim is to promote further discussion and promote the drafting of a code. This paper includes a summary of other ethical codes that may provide a starting point. The time for reform is upon us, and there is an urgent need for an independent body to take the lead, for fear of floundering and having only found ‘another debating topic’ (Uff 2006.

Methodology, status and plans for development and assessment of Cathare code

Energy Technology Data Exchange (ETDEWEB)

Bestion, D.; Barre, F.; Faydide, B. [CEA - Grenoble (France)

1997-07-01

This paper presents the methodology, status and plans for the development, assessment and uncertainty evaluation of the Cathare code. Cathare is a thermalhydraulic code developed by CEA (DRN), IPSN, EDF and FRAMATOME for PWR safety analysis. First, the status of the code development and assessment is presented. The general strategy used for the development and the assessment of the code is presented. Analytical experiments with separate effect tests, and component tests are used for the development and the validation of closure laws. Successive Revisions of constitutive laws are implemented in successive Versions of the code and assessed. System tests or integral tests are used to validate the general consistency of the Revision. Each delivery of a code Version + Revision is fully assessed and documented. A methodology is being developed to determine the uncertainty on all constitutive laws of the code using calculations of many analytical tests and applying the Discrete Adjoint Sensitivity Method (DASM). At last, the plans for the future developments of the code are presented. They concern the optimization of the code performance through parallel computing - the code will be used for real time full scope plant simulators - the coupling with many other codes (neutronic codes, severe accident codes), the application of the code for containment thermalhydraulics. Also, physical improvements are required in the field of low pressure transients and in the modeling for the 3-D model.

Developments of HTGR thermofluid dynamic analysis codes and HTGR plant dynamic simulation code

International Nuclear Information System (INIS)

Tanaka, Mitsuhiro; Izaki, Makoto; Koike, Hiroyuki; Tokumitsu, Masashi

1983-01-01

In nuclear power plants as well as high temperature gas-cooled reactor plants, the design is mostly performed on the basis of the results after their characteristics have been grasped by carrying out the numerical simulation using the analysis code. Also in Kawasaki Heavy Industries Ltd., on the basis of the system engineering accumulated with gas-cooled reactors since several years ago, the preparation and systematization of analysis codes have been advanced, aiming at lining up the analysis codes for heat transferring flow and control characteristics, taking up HTGR plants as the main object. In this report, a part of the results is described. The example of the analysis applying the two-dimensional compressible flow analysis codes SOLA-VOF and SALE-2D, which were developed by Los Alamos National Laboratory in USA and modified for use in Kawasaki, to HTGR system is reported. Besides, Kawasaki has developed the control characteristics analyzing code DYSCO by which the change of system composition is easy and high versatility is available. The outline, fundamental equations, fundamental algorithms and examples of application of the SOLA-VOF and SALE-2D, the present status of system characteristic simulation codes and the outline of the DYSCO are described. (Kako, I.)

Development of ADINA-J-integral code

International Nuclear Information System (INIS)

Kurihara, Ryoichi

1988-07-01

A general purpose finite element program ADINA (Automatic Dynamic Incremental Nonlinear Analysis), which was developed by Bathe et al., was revised to be able to calculate the J- and J-integral. This report introduced the numerical method to add this capability to the code, and the evaluation of the revised ADINA-J code by using a few of examples of the J estimation model, i.e. a compact tension specimen, a center cracked panel subjected to dynamic load, and a thick shell cylinder having inner axial crack subjected to thermal load. The evaluation testified the function of the revised code. (author)

Development and application of best-estimate LWR safety analysis codes

International Nuclear Information System (INIS)

Reocreux, M.

1997-01-01

This paper is a review of the status and the future orientations of the development and application of best estimate LWR safety analysis codes. The present status of these codes exhibits a large success and almost a complete fulfillment of the objectives which were assigned in the 70s. The applications of Best Estimate codes are numerous and cover a large variety of safety questions. However these applications raised a number of problems. The first ones concern the need to have a better control of the quality of the results. This means requirements on code assessment and on uncertainties evaluation. The second ones concern needs for code development and specifically regarding physical models, numerics, coupling with other codes and programming. The analysis of the orientations for code developments and applications in the next years, shows that some developments should be made without delay in order to solve today questions whereas some others are more long term and should be tested for example in some pilot programmes before being eventually applied in main code development. Each of these development programmes are analyzed in the paper by detailing their main content and their possible interest. (author)

Development of codes for physical calculations of WWER

International Nuclear Information System (INIS)

Novikov, A.N.

2000-01-01

A package of codes for physical calculations of WWER reactors, used at the RRC 'Kurchatov Institute' is discussed including the purpose of these codes, approximations used, degree of data verification, possibilities of automation of calculations and presentation of results, trends of further development of the codes. (Authors)

SCDAP/RELAP5 code development and assessment

International Nuclear Information System (INIS)

Allison, C.M.; Hohorst, J.K.

1996-01-01

The SCDAP/RELAP5 computer code is designed to describe the overall reactor coolant system thermal-hydraulic response, core damage progression, and fission product release during severe accidents. The code is being developed at the Idaho National Engineering Laboratory under the primary sponsorship of the Office of Nuclear Regulatory Research of the U.S. Nuclear Regulatory Commission. The current version of the code is SCDAP/RELAP5/MOD3.1e. Although MOD3.1e contains a number of significant improvements since the initial version of MOD3.1 was released, new models to treat the behavior of the fuel and cladding during reflood have had the most dramatic impact on the code's calculations. This paper provides a brief description of the new reflood models, presents highlights of the assessment of the current version of MOD3.1, and discusses future SCDAP/RELAP5/MOD3.2 model development activities

Development of Regulatory Audit Core Safety Code : COREDAX

Energy Technology Data Exchange (ETDEWEB)

Yang, Chae Yong; Jo, Jong Chull; Roh, Byung Hwan [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of); Lee, Jae Jun; Cho, Nam Zin [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

2005-07-01

Korea Institute of Nuclear Safety (KINS) has developed a core neutronics simulator, COREDAX code, for verifying core safety of SMART-P reactor, which is technically supported by Korea Advanced Institute of Science and Technology (KAIST). The COREDAX code would be used for regulatory audit calculations of 3- dimendional core neutronics. The COREDAX code solves the steady-state and timedependent multi-group neutron diffusion equation in hexagonal geometry as well as rectangular geometry by analytic function expansion nodal (AFEN) method. AFEN method was developed at KAIST, and it was internationally verified that its accuracy is excellent. The COREDAX code is originally programmed based on the AFEN method. Accuracy of the code on the AFEN method was excellent for the hexagonal 2-dimensional problems, but there was a need for improvement for hexagonal-z 3-dimensional problems. Hence, several solution routines of the AFEN method are improved, and finally the advanced AFEN method is created. COREDAX code is based on the advanced AFEN method . The initial version of COREDAX code is to complete a basic framework, performing eigenvalue calculations and kinetics calculations with thermal-hydraulic feedbacks, for audit calculations of steady-state core design and reactivity-induced accidents of SMART-P reactor. This study describes the COREDAX code for hexagonal geometry.

Development of a domestically-made system code

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

According to lessons learned from the Fukushima-Daiichi NPP accidents, a new safety standard based on state-of-the-art findings has been established by the Japanese Nuclear Regulation Authority (NRA) and will soon come into force in Japan. In order to ensure a precise response to this movement from a technological point of view, it should be required for safety regulation to develop a new system code with much smaller uncertainty and reinforced simulation capability even in application to beyond-DBAs (BDBAs), as well as with the capability of close coupling to a newly developing severe accident code. Accordingly, development of a new domestically-made system code that incorporates 3-dimensional and 3 or more fluid thermal-hydraulics in tandem with a 3-dimensional neutronics has been started in 2012. In 2012, two branches of development activities, the development of 'main body' and advanced features have been started in parallel for development efficiency. The main body has been started from scratch and the following activities have therefore been performed: 1) development and determination of key principles and methodologies to realize a flexible, extensible and robust platform, 2) determination of requirements definition, 3) start of basic program design and coding and 4) start of a development of prototypical GUI-based pre-post processor. As for the advanced features, the following activities have been performed: 1) development of Phenomena Identification and Ranking Tables (PIRTs) and model capability matrix from normal operations to BDBAs in order to address requirements definition for advanced modeling, 2) development of detailed action plan for modification of field equations, numerical schemes and solvers and 3) start of the program development of field equations with an interfacial area concentration transport equation, a robust solver for condensation induced water hammer phenomena and a versatile Newton-Raphson solver. (author)

Development of the point-depletion code DEPTH

International Nuclear Information System (INIS)

She, Ding; Wang, Kan; Yu, Ganglin

2013-01-01

Highlights: ► The DEPTH code has been developed for the large-scale depletion system. ► DEPTH uses the data library which is convenient to couple with MC codes. ► TTA and matrix exponential methods are implemented and compared. ► DEPTH is able to calculate integral quantities based on the matrix inverse. ► Code-to-code comparisons prove the accuracy and efficiency of DEPTH. -- Abstract: The burnup analysis is an important aspect in reactor physics, which is generally done by coupling of transport calculations and point-depletion calculations. DEPTH is a newly-developed point-depletion code of handling large burnup depletion systems and detailed depletion chains. For better coupling with Monte Carlo transport codes, DEPTH uses data libraries based on the combination of ORIGEN-2 and ORIGEN-S and allows users to assign problem-dependent libraries for each depletion step. DEPTH implements various algorithms of treating the stiff depletion systems, including the Transmutation trajectory analysis (TTA), the Chebyshev Rational Approximation Method (CRAM), the Quadrature-based Rational Approximation Method (QRAM) and the Laguerre Polynomial Approximation Method (LPAM). Three different modes are supported by DEPTH to execute the decay, constant flux and constant power calculations. In addition to obtaining the instantaneous quantities of the radioactivity, decay heats and reaction rates, DEPTH is able to calculate the integral quantities by a time-integrated solver. Through calculations compared with ORIGEN-2, the validity of DEPTH in point-depletion calculations is proved. The accuracy and efficiency of depletion algorithms are also discussed. In addition, an actual pin-cell burnup case is calculated to illustrate the DEPTH code performance in coupling with the RMC Monte Carlo code

Challenges on innovations of newly-developed safety analysis codes

International Nuclear Information System (INIS)

Yang, Yanhua; Zhang, Hao

2016-01-01

With the development of safety analysis method, the safety analysis codes meet more challenges. Three challenges are presented in this paper, which are mathematic model, code design and user interface. Combined with the self-reliance safety analysis code named COSINE, the ways of meeting these requirements are suggested, that is to develop multi-phases, multi-fields and multi-dimension models, to adopt object-oriented code design ideal and to improve the way of modeling, calculation control and data post-processing in the user interface.

Challenges on innovations of newly-developed safety analysis codes

Energy Technology Data Exchange (ETDEWEB)

Yang, Yanhua [Shanghai Jiao Tong Univ. (China). School of Nuclear Science and Engineering; Zhang, Hao [State Nuclear Power Software Development Center, Beijing (China). Beijing Future Science and Technology City

2016-05-15

With the development of safety analysis method, the safety analysis codes meet more challenges. Three challenges are presented in this paper, which are mathematic model, code design and user interface. Combined with the self-reliance safety analysis code named COSINE, the ways of meeting these requirements are suggested, that is to develop multi-phases, multi-fields and multi-dimension models, to adopt object-oriented code design ideal and to improve the way of modeling, calculation control and data post-processing in the user interface.

Recent developments in the CONTAIN-LMR code

International Nuclear Information System (INIS)

Murata, K.K.

1990-01-01

Through an international collaborative effort, a special version of the CONTAIN code is being developed for integrated mechanistic analysis of the conditions in liquid metal reactor (LMR) containments during severe accidents. The capabilities of the most recent code version, CONTAIN LMR/1B-Mod.1, are discussed. These include new models for the treatment of two condensables, sodium condensation on aerosols, chemical reactions, hygroscopic aerosols, and concrete outgassing. This code version also incorporates all of the previously released LMR model enhancements. The results of an integral demonstration calculation of a sever core-melt accident scenario are given to illustrate the features of this code version. 11 refs., 7 figs., 1 tab

HELIAS module development for systems codes

Energy Technology Data Exchange (ETDEWEB)

Warmer, F., E-mail: Felix.Warmer@ipp.mpg.de; Beidler, C.D.; Dinklage, A.; Egorov, K.; Feng, Y.; Geiger, J.; Schauer, F.; Turkin, Y.; Wolf, R.; Xanthopoulos, P.

2015-02-15

In order to study and design next-step fusion devices such as DEMO, comprehensive systems codes are commonly employed. In this work HELIAS-specific models are proposed which are designed to be compatible with systems codes. The subsequently developed models include: a geometry model based on Fourier coefficients which can represent the complex 3-D plasma shape, a basic island divertor model which assumes diffusive cross-field transport and high radiation at the X-point, and a coil model which combines scaling aspects based on the HELIAS 5-B reactor design in combination with analytic inductance and field calculations. In addition, stellarator-specific plasma transport is discussed. A strategy is proposed which employs a predictive confinement time scaling derived from 1-D neoclassical and 3-D turbulence simulations. This paper reports on the progress of the development of the stellarator-specific models while an implementation and verification study within an existing systems code will be presented in a separate work. This approach is investigated to ultimately allow one to conduct stellarator system studies, develop design points of HELIAS burning plasma devices, and to facilitate a direct comparison between tokamak and stellarator DEMO and power plant designs.

Development of the next generation reactor analysis code system, MARBLE

International Nuclear Information System (INIS)

Yokoyama, Kenji; Hazama, Taira; Nagaya, Yasunobu; Chiba, Go; Kugo, Teruhiko; Ishikawa, Makoto; Tatsumi, Masahiro; Hirai, Yasushi; Hyoudou, Hideaki; Numata, Kazuyuki; Iwai, Takehiko; Jin, Tomoyuki

2011-03-01

A next generation reactor analysis code system, MARBLE, has been developed. MARBLE is a successor of the fast reactor neutronics analysis code systems, JOINT-FR and SAGEP-FR (conventional systems), which were developed for so-called JUPITER standard analysis methods. MARBLE has the equivalent analysis capability to the conventional system because MARBLE can utilize sub-codes included in the conventional system without any change. On the other hand, burnup analysis functionality for power reactors is improved compared with the conventional system by introducing models on fuel exchange treatment and control rod operation and so on. In addition, MARBLE has newly developed solvers and some new features of burnup calculation by the Krylov sub-space method and nuclear design accuracy evaluation by the extended bias factor method. In the development of MARBLE, the object oriented technology was adopted from the view-point of improvement of the software quality such as flexibility, expansibility, facilitation of the verification by the modularization and assistance of co-development. And, software structure called the two-layer system consisting of scripting language and system development language was applied. As a result, MARBLE is not an independent analysis code system which simply receives input and returns output, but an assembly of components for building an analysis code system (i.e. framework). Furthermore, MARBLE provides some pre-built analysis code systems such as the fast reactor neutronics analysis code system. SCHEME, which corresponds to the conventional code and the fast reactor burnup analysis code system, ORPHEUS. (author)

Development and Application of a Code for Internal Exposure (CINEX) based on the CINDY code

International Nuclear Information System (INIS)

Kravchik, T.; Duchan, N.; Sarah, R.; Gabay, Y.; Kol, R.

2004-01-01

Internal exposure to radioactive materials at the NRCN is evaluated using the CINDY (Code for Internal Dosimetry) Package. The code was developed by the Pacific Northwest Laboratory to assist the interpretation of bioassay data, provide bioassay projections and evaluate committed and calendar-year doses from intake or bioassay measurement data. It provides capabilities to calculate organ dose and effective dose equivalents using the International Commission on Radiological Protection (ICRP) 30 approach. The CINDY code operates under DOS operating system and consequently its operation needs a relatively long procedure which also includes a lot of manual typing that can lead to personal human mistakes. A new code has been developed at the NRCN, the CINEX (Code for Internal Exposure), which is an Excel application and leads to a significant reduction in calculation time (in the order of 5-10 times) and in the risk of personal human mistakes. The code uses a database containing tables which were constructed by the CINDY and contain the bioassay values predicted by the ICRP30 model after an intake of an activity unit of each isotope. Using the database, the code than calculates the appropriate intake and consequently the committed effective dose and organ dose. Calculations with the CINEX code were compared to similar calculations with the CINDY code. The discrepancies were less than 5%, which is the rounding error of the CINDY code. Attached is a table which compares parameters calculated with the CINEX and the CINDY codes (for a class Y uranium). The CINEX is now used at the NRCN to calculate occupational intakes and doses to workers with radioactive materials

Code Development and Analysis Program: developmental checkout of the BEACON/MOD2A code

International Nuclear Information System (INIS)

Ramsthaler, J.A.; Lime, J.F.; Sahota, M.S.

1978-12-01

A best-estimate transient containment code, BEACON, is being developed by EG and G Idaho, Inc. for the Nuclear Regulatory Commission's reactor safety research program. This is an advanced, two-dimensional fluid flow code designed to predict temperatures and pressures in a dry PWR containment during a hypothetical loss-of-coolant accident. The most recent version of the code, MOD2A, is presently in the final stages of production prior to being released to the National Energy Software Center. As part of the final code checkout, seven sample problems were selected to be run with BEACON/MOD2A

Development of a tritium dispersion code

International Nuclear Information System (INIS)

Bell, R.P.; Davis, M.W.; Joseph, S.; Wong, K.Y.

1985-01-01

This paper describes the development and verification of a computer code designed to calculate the radiation dose to man following acute or chronic atmospheric releases of tritium gas and oxide from a point source. The Ontario Hydro Tritium Dispersion Code calculates tritium concentrations in air, soil, and vegetation and doses to man resulting from inhalation/immersion and ingestion of food, milk meat and water. The deposition of HT to soil, conversion of HT to HTO by soil enzymes and resuspension of HTO to air have been incorporated into the terrestrial compartment model and are unique features of the code. Sensitivity analysis has identified the HT deposition velocity and the equivalent water depth of the vegetation compartment as two parameters which have a strong influence on dose calculations. Tritium concentrations in vegetation and soil calculated by the code were in reasonable agreement with experimental results. The radiological significance of including the mechanisms of HT to HTO conversion and resuspension of HTO to air is illustrated

Recent developments in KTF. Code optimization and improved numerics

International Nuclear Information System (INIS)

Jimenez, Javier; Avramova, Maria; Sanchez, Victor Hugo; Ivanov, Kostadin

2012-01-01

The rapid increase of computer power in the last decade facilitated the development of high fidelity simulations in nuclear engineering allowing a more realistic and accurate optimization as well as safety assessment of reactor cores and power plants compared to the legacy codes. Thermal hydraulic subchannel codes together with time dependent neutron transport codes are the options of choice for an accurate prediction of local safety parameters. Moreover, fast running codes with the best physical models are needed for high fidelity coupled thermal hydraulic / neutron kinetic solutions. Hence at KIT, different subchannel codes such as SUBCHANFLOW and KTF are being improved, validated and coupled with different neutron kinetics solutions. KTF is a subchannel code developed for best-estimate analysis of both Pressurized Water Reactor (PWR) and BWR. It is based on the Pennsylvania State University (PSU) version of COBRA-TF (Coolant Boling in Rod Arrays Two Fluids) named CTF. In this paper, the investigations devoted to the enhancement of the code numeric and informatics structure are presented and discussed. By some examples the gain on code speed-up will be demonstrated and finally an outlook of further activities concentrated on the code improvements will be given. (orig.)

Recent developments in KTF. Code optimization and improved numerics

Energy Technology Data Exchange (ETDEWEB)

Jimenez, Javier; Avramova, Maria; Sanchez, Victor Hugo; Ivanov, Kostadin [Karlsruhe Institute of Technology (KIT) (Germany). Inst. for Neutron Physics and Reactor Technology (INR)

2012-11-01

The rapid increase of computer power in the last decade facilitated the development of high fidelity simulations in nuclear engineering allowing a more realistic and accurate optimization as well as safety assessment of reactor cores and power plants compared to the legacy codes. Thermal hydraulic subchannel codes together with time dependent neutron transport codes are the options of choice for an accurate prediction of local safety parameters. Moreover, fast running codes with the best physical models are needed for high fidelity coupled thermal hydraulic / neutron kinetic solutions. Hence at KIT, different subchannel codes such as SUBCHANFLOW and KTF are being improved, validated and coupled with different neutron kinetics solutions. KTF is a subchannel code developed for best-estimate analysis of both Pressurized Water Reactor (PWR) and BWR. It is based on the Pennsylvania State University (PSU) version of COBRA-TF (Coolant Boling in Rod Arrays Two Fluids) named CTF. In this paper, the investigations devoted to the enhancement of the code numeric and informatics structure are presented and discussed. By some examples the gain on code speed-up will be demonstrated and finally an outlook of further activities concentrated on the code improvements will be given. (orig.)

Development of code SFINEL (Spent fuel integrity evaluator)

Energy Technology Data Exchange (ETDEWEB)

Kim, Yong Soo; Min, Chin Young; Ohk, Young Kil; Yang, Yong Sik; Kim, Dong Ju; Kim, Nam Ku [Hanyang University, Seoul (Korea)

1999-01-01

SFINEL code, an integrated computer program for predicting the spent fuel rod integrity based on burn-up history and major degradation mechanisms, has been developed through this project. This code can sufficiently simulate the power history of a fuel rod during the reactor operation and estimate the degree of deterioration of spent fuel cladding using the recently-developed models on the degradation mechanisms. SFINEL code has been thoroughly benchmarked against the collected in-pile data and operating experiences: deformation and rupture, and cladding oxidation, rod internal pressure creep, then comprehensive whole degradation process. (author). 75 refs., 51 figs., 5 tabs.

Development of FBR integrity system code. Basic concept

International Nuclear Information System (INIS)

Asayama, Tai

2001-05-01

For fast breeder reactors to be commercialized, they must be more reliable, safer, and at the same, economically competitive with future light water reactors. Innovation of elevated temperature structural design standard is necessary to achieve this goal. The most powerful way is to enlarge the scope of structural integrity code to cover items other than design evaluation that has been addressed in existing codes. Items that must be newly covered are prerequisites of design, fabrication, examination, operation and maintenance, etc. This allows designers to choose the most economical combination of design variations to achieve specific reliability that is needed for a particular component. Designing components by this concept, a cost-minimum design of a whole plant can be realized. By determining the reliability that must be achieved for a component by risk technologies, further economical improvement can be expected by avoiding excessive quality. Recognizing the necessity for the codes based on the new concept, the development of 'FBR integrity system code' began in 2000. Research and development will last 10 years. For this development, the basic logistics and system as well as technologies that materialize the concept are necessary. Original logistics and system must be developed, because no existing researches are available in and out of Japan. This reports presents the results of the work done in the first year regarding the basic idea, methodology, and structure of the code. (author)

Development of authentication code for multi-access optical code division multiplexing based quantum key distribution

Science.gov (United States)

Taiwo, Ambali; Alnassar, Ghusoon; Bakar, M. H. Abu; Khir, M. F. Abdul; Mahdi, Mohd Adzir; Mokhtar, M.

2018-05-01

One-weight authentication code for multi-user quantum key distribution (QKD) is proposed. The code is developed for Optical Code Division Multiplexing (OCDMA) based QKD network. A unique address assigned to individual user, coupled with degrading probability of predicting the source of the qubit transmitted in the channel offer excellent secure mechanism against any form of channel attack on OCDMA based QKD network. Flexibility in design as well as ease of modifying the number of users are equally exceptional quality presented by the code in contrast to Optical Orthogonal Code (OOC) earlier implemented for the same purpose. The code was successfully applied to eight simultaneous users at effective key rate of 32 bps over 27 km transmission distance.

Development of HTGR plant dynamics simulation code

International Nuclear Information System (INIS)

Ohashi, Kazutaka; Tazawa, Yujiro; Mitake, Susumu; Suzuki, Katsuo.

1987-01-01

Plant dynamics simulation analysis plays an important role in the design work of nuclear power plant especially in the plant safety analysis, control system analysis, and transient condition analysis. The authors have developed the plant dynamics simulation code named VESPER, which is applicable to the design work of High Temperature Engineering Test Reactor, and have been improving the code corresponding to the design changes made in the subsequent design works. This paper describes the outline of VESPER code and shows its sample calculation results selected from the recent design work. (author)

Integrated code development for studying laser driven plasmas

Energy Technology Data Exchange (ETDEWEB)

Takabe, Hideaki; Nagatomo, Hideo; Sunahara, Atsusi; Ohnishi, Naofumi; Naruo, Syuji; Mima, Kunioki [Osaka Univ., Suita (Japan). Inst. of Laser Engineering

1998-03-01

Present status and plan for developing an integrated implosion code are briefly explained by focusing on motivation, numerical scheme and issues to be developed more. Highly nonlinear stage of Rayleigh-Taylor instability of ablation front by laser irradiation has been simulated so as to be compared with model experiments. Improvement in transport and rezoning/remapping algorithms in ILESTA code is described. (author)

Coupled geochemical and solute transport code development

International Nuclear Information System (INIS)

Morrey, J.R.; Hostetler, C.J.

1985-01-01

A number of coupled geochemical hydrologic codes have been reported in the literature. Some of these codes have directly coupled the source-sink term to the solute transport equation. The current consensus seems to be that directly coupling hydrologic transport and chemical models through a series of interdependent differential equations is not feasible for multicomponent problems with complex geochemical processes (e.g., precipitation/dissolution reactions). A two-step process appears to be the required method of coupling codes for problems where a large suite of chemical reactions must be monitored. Two-step structure requires that the source-sink term in the transport equation is supplied by a geochemical code rather than by an analytical expression. We have developed a one-dimensional two-step coupled model designed to calculate relatively complex geochemical equilibria (CTM1D). Our geochemical module implements a Newton-Raphson algorithm to solve heterogeneous geochemical equilibria, involving up to 40 chemical components and 400 aqueous species. The geochemical module was designed to be efficient and compact. A revised version of the MINTEQ Code is used as a parent geochemical code

Code development and analyses within the area of transmutation and safety

International Nuclear Information System (INIS)

Maschek, W.

2002-01-01

A strong code development is going on to meet various demands resulting from the development of dedicated reactors for transmutation and incineration. Code development is concerned with safety codes and general codes needed for assessing scenarios and transmutation strategies. Analyses concentrate on various ADS systems with solid and liquid molten salt fuels. Analyses deal with ADS Demo Plant (5th FP EU) and transmuters with advanced fuels

The development of code benchmarks

International Nuclear Information System (INIS)

Glass, R.E.

1986-01-01

Sandia National Laboratories has undertaken a code benchmarking effort to define a series of cask-like problems having both numerical solutions and experimental data. The development of the benchmarks includes: (1) model problem definition, (2) code intercomparison, and (3) experimental verification. The first two steps are complete and a series of experiments are planned. The experiments will examine the elastic/plastic behavior of cylinders for both the end and side impacts resulting from a nine meter drop. The cylinders will be made from stainless steel and aluminum to give a range of plastic deformations. This paper presents the results of analyses simulating the model's behavior using materials properties for stainless steel and aluminum

Development of Evaluation Code for MUF Uncertainty

International Nuclear Information System (INIS)

Won, Byung Hee; Han, Bo Young; Shin, Hee Sung; Ahn, Seong-Kyu; Park, Geun-Il; Park, Se Hwan

2015-01-01

Material Unaccounted For (MUF) is the material balance evaluated by measured nuclear material in a Material Balance Area (MBA). Assuming perfect measurements and no diversion from a facility, one can expect a zero MUF. However, non-zero MUF is always occurred because of measurement uncertainty even though the facility is under normal operation condition. Furthermore, there are many measurements using different equipment at various Key Measurement Points (KMPs), and the MUF uncertainty is affected by errors of those measurements. Evaluating MUF uncertainty is essentially required to develop safeguards system including nuclear measurement system in pyroprocessing, which is being developed for reducing radioactive waste from spent fuel in Korea Atomic Energy Research Institute (KAERI). The evaluation code for analyzing MUF uncertainty has been developed and it was verified using sample problem from the IAEA reference. MUF uncertainty can be simply and quickly calculated by using this evaluation code which is made based on graphical user interface for user friendly. It is also expected that the code will make the sensitivity analysis on the MUF uncertainty for the various safeguards systems easy and more systematic. It is suitable for users who want to evaluate the conventional safeguards system as well as to develop a new system for developing facilities

Development of Evaluation Code for MUF Uncertainty

Energy Technology Data Exchange (ETDEWEB)

Won, Byung Hee; Han, Bo Young; Shin, Hee Sung; Ahn, Seong-Kyu; Park, Geun-Il; Park, Se Hwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

Material Unaccounted For (MUF) is the material balance evaluated by measured nuclear material in a Material Balance Area (MBA). Assuming perfect measurements and no diversion from a facility, one can expect a zero MUF. However, non-zero MUF is always occurred because of measurement uncertainty even though the facility is under normal operation condition. Furthermore, there are many measurements using different equipment at various Key Measurement Points (KMPs), and the MUF uncertainty is affected by errors of those measurements. Evaluating MUF uncertainty is essentially required to develop safeguards system including nuclear measurement system in pyroprocessing, which is being developed for reducing radioactive waste from spent fuel in Korea Atomic Energy Research Institute (KAERI). The evaluation code for analyzing MUF uncertainty has been developed and it was verified using sample problem from the IAEA reference. MUF uncertainty can be simply and quickly calculated by using this evaluation code which is made based on graphical user interface for user friendly. It is also expected that the code will make the sensitivity analysis on the MUF uncertainty for the various safeguards systems easy and more systematic. It is suitable for users who want to evaluate the conventional safeguards system as well as to develop a new system for developing facilities.

The Development of the World Anti-Doping Code.

Science.gov (United States)

Young, Richard

2017-01-01

This chapter addresses both the development and substance of the World Anti-Doping Code, which came into effect in 2003, as well as the subsequent Code amendments, which came into effect in 2009 and 2015. Through an extensive process of stakeholder input and collaboration, the World Anti-Doping Code has transformed the hodgepodge of inconsistent and competing pre-2003 anti-doping rules into a harmonized and effective approach to anti-doping. The Code, as amended, is now widely recognized worldwide as the gold standard in anti-doping. The World Anti-Doping Code originally went into effect on January 1, 2004. The first amendments to the Code went into effect on January 1, 2009, and the second amendments on January 1, 2015. The Code and the related international standards are the product of a long and collaborative process designed to make the fight against doping more effective through the adoption and implementation of worldwide harmonized rules and best practices. © 2017 S. Karger AG, Basel.

Development of probabilistic fracture mechanics code PASCAL and user's manual

Energy Technology Data Exchange (ETDEWEB)

Shibata, Katsuyuki; Onizawa, Kunio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Li, Yinsheng; Kato, Daisuke [Fuji Research Institute Corporation, Tokyo (Japan)

2001-03-01

As a part of the aging and structural integrity research for LWR components, a new PFM (Probabilistic Fracture Mechanics) code PASCAL (PFM Analysis of Structural Components in Aging LWR) has been developed since FY1996. This code evaluates the failure probability of an aged reactor pressure vessel subjected to transient loading such as PTS (Pressurized Thermal Shock). The development of the code has been aimed to improve the accuracy and reliability of analysis by introducing new analysis methodologies and algorithms considering the recent development in the fracture mechanics methodologies and computer performance. The code has some new functions in optimized sampling and cell dividing procedure in stratified Monte Carlo simulation, elastic-plastic fracture criterion of R6 method, extension analysis models in semi-elliptical crack, evaluation of effect of thermal annealing and etc. In addition, an input data generator of temperature and stress distribution time histories was also prepared in the code. Functions and performance of the code have been confirmed based on the verification analyses and some case studies on the influence parameters. The present phase of the development will be completed in FY2000. Thus this report provides the user's manual and theoretical background of the code. (author)

SWAAM code development, verification and application to steam generator design

International Nuclear Information System (INIS)

Shin, Y.W.; Valentin, R.A.

1990-01-01

This paper describes the family of SWAAM codes developed by Argonne National Laboratory to analyze the effects of sodium/water reactions on LMR steam generators. The SWAAM codes were developed as design tools for analyzing various phenomena related to steam generator leaks and to predict the resulting thermal and hydraulic effects on the steam generator and the intermediate heat transport system (IHTS). The theoretical foundations and numerical treatments on which the codes are based are discussed, followed by a description of code capabilities and limitations, verification of the codes by comparison with experiment, and applications to steam generator and IHTS design. (author). 25 refs, 14 figs

Development of the versatile reactor analysis code system, MARBLE2

International Nuclear Information System (INIS)

Yokoyama, Kenji; Jin, Tomoyuki; Hazama, Taira; Hirai, Yasushi

2015-07-01

The second version of the versatile reactor analysis code system, MARBLE2, has been developed. A lot of new functions have been added in MARBLE2 by using the base technology developed in the first version (MARBLE1). Introducing the remaining functions of the conventional code system (JOINT-FR and SAGEP-FR), MARBLE2 enables one to execute almost all analysis functions of the conventional code system with the unified user interfaces of its subsystem, SCHEME. In particular, the sensitivity analysis functionality is available in MARBLE2. On the other hand, new built-in solvers have been developed, and existing ones have been upgraded. Furthermore, some other analysis codes and libraries developed in JAEA have been consolidated and prepared in SCHEME. In addition, several analysis codes developed in the other institutes have been additionally introduced as plug-in solvers. Consequently, gamma-ray transport calculation and heating evaluation become available. As for another subsystem, ORPHEUS, various functionality updates and speed-up techniques have been applied based on user experience of MARBLE1 to enhance its usability. (author)

Development of TIME2 code

International Nuclear Information System (INIS)

1986-02-01

The paper reviews the progress on the development of a computer model TIME2, for modelling the long term evolution of shallow burial site environments for low- and intermediate-level radioactive waste disposal. The subject is discussed under the five topic headings: 1) background studies, including geomorphology, climate, human-induced effects, and seismicity, 2) development of the TIME2 code, 3) verification and testing, 4) documentation, and, 5) role of TIME2 in radiological risk assessment. (U.K.)

Theoretical atomic physics code development III TAPS: A display code for atomic physics data

International Nuclear Information System (INIS)

Clark, R.E.H.; Abdallah, J. Jr.; Kramer, S.P.

1988-12-01

A large amount of theoretical atomic physics data is becoming available through use of the computer codes CATS and ACE developed at Los Alamos National Laboratory. A new code, TAPS, has been written to access this data, perform averages over terms and configurations, and display information in graphical or text form. 7 refs., 13 figs., 1 tab

Development of LWR fuel performance code FEMAXI-6

International Nuclear Information System (INIS)

Suzuki, Motoe

2006-01-01

LWR fuel performance code: FEMAXI-6 (Finite Element Method in AXIs-symmetric system) is a representative fuel analysis code in Japan. Development history, background, design idea, features of model, and future are stated. Characteristic performance of LWR fuel and analysis code, what is model, development history of FEMAXI, use of FEMAXI code, fuel model, and a special feature of FEMAXI model is described. As examples of analysis, PCMI (Pellet-Clad Mechanical Interaction), fission gas release, gap bonding, and fission gas bubble swelling are reported. Thermal analysis and dynamic analysis system of FEMAXI-6, function block at one time step of FEMAXI-6, analytical example of PCMI in the output increase test by FEMAXI-III, analysis of fission gas release in Halden reactor by FEMAXI-V, comparison of the center temperature of fuel in Halden reactor, and analysis of change of diameter of fuel rod in high burn up BWR fuel are shown. (S.Y.)

Code development for nuclear reactor simulation

International Nuclear Information System (INIS)

Chauliac, C.; Verwaerde, D.; Pavageau, O.

2006-01-01

Full text of publication follows: Since several years, CEA, EDF and FANP have developed several numerical codes which are currently used for nuclear industry applications and will be remain in use for the coming years. Complementary to this set of codes and in order to better meet the present and future needs, a new system is being developed through a joint venture between CEA, EDF and FANP, with a ten year prospect and strong intermediate milestones. The focus is put on a multi-scale and multi-physics approach enabling to take into account phenomena from microscopic to macroscopic scale, and to describe interactions between various physical fields such as neutronics (DESCARTES), thermal-hydraulics (NEPTUNE) and fuel behaviour (PLEIADES). This approach is based on a more rational design of the softwares and uses a common integration platform providing pre-processing, supervision of computation and post-processing. This paper will describe the overall system under development and present the first results obtained. (authors)

Foundational development of an advanced nuclear reactor integrated safety code

International Nuclear Information System (INIS)

Clarno, Kevin; Lorber, Alfred Abraham; Pryor, Richard J.; Spotz, William F.; Schmidt, Rodney Cannon; Belcourt, Kenneth; Hooper, Russell Warren; Humphries, Larry LaRon

2010-01-01

This report describes the activities and results of a Sandia LDRD project whose objective was to develop and demonstrate foundational aspects of a next-generation nuclear reactor safety code that leverages advanced computational technology. The project scope was directed towards the systems-level modeling and simulation of an advanced, sodium cooled fast reactor, but the approach developed has a more general applicability. The major accomplishments of the LDRD are centered around the following two activities. (1) The development and testing of LIME, a Lightweight Integrating Multi-physics Environment for coupling codes that is designed to enable both 'legacy' and 'new' physics codes to be combined and strongly coupled using advanced nonlinear solution methods. (2) The development and initial demonstration of BRISC, a prototype next-generation nuclear reactor integrated safety code. BRISC leverages LIME to tightly couple the physics models in several different codes (written in a variety of languages) into one integrated package for simulating accident scenarios in a liquid sodium cooled 'burner' nuclear reactor. Other activities and accomplishments of the LDRD include (a) further development, application and demonstration of the 'non-linear elimination' strategy to enable physics codes that do not provide residuals to be incorporated into LIME, (b) significant extensions of the RIO CFD code capabilities, (c) complex 3D solid modeling and meshing of major fast reactor components and regions, and (d) an approach for multi-physics coupling across non-conformal mesh interfaces.

Foundational development of an advanced nuclear reactor integrated safety code.

Energy Technology Data Exchange (ETDEWEB)

Clarno, Kevin (Oak Ridge National Laboratory, Oak Ridge, TN); Lorber, Alfred Abraham; Pryor, Richard J.; Spotz, William F.; Schmidt, Rodney Cannon; Belcourt, Kenneth (Ktech Corporation, Albuquerque, NM); Hooper, Russell Warren; Humphries, Larry LaRon

2010-02-01

This report describes the activities and results of a Sandia LDRD project whose objective was to develop and demonstrate foundational aspects of a next-generation nuclear reactor safety code that leverages advanced computational technology. The project scope was directed towards the systems-level modeling and simulation of an advanced, sodium cooled fast reactor, but the approach developed has a more general applicability. The major accomplishments of the LDRD are centered around the following two activities. (1) The development and testing of LIME, a Lightweight Integrating Multi-physics Environment for coupling codes that is designed to enable both 'legacy' and 'new' physics codes to be combined and strongly coupled using advanced nonlinear solution methods. (2) The development and initial demonstration of BRISC, a prototype next-generation nuclear reactor integrated safety code. BRISC leverages LIME to tightly couple the physics models in several different codes (written in a variety of languages) into one integrated package for simulating accident scenarios in a liquid sodium cooled 'burner' nuclear reactor. Other activities and accomplishments of the LDRD include (a) further development, application and demonstration of the 'non-linear elimination' strategy to enable physics codes that do not provide residuals to be incorporated into LIME, (b) significant extensions of the RIO CFD code capabilities, (c) complex 3D solid modeling and meshing of major fast reactor components and regions, and (d) an approach for multi-physics coupling across non-conformal mesh interfaces.

FDA Developments: Food Code 2013 and Proposed Trans Fat Determination

NARCIS (Netherlands)

Grossman, M.R.

2014-01-01

268 Reports EFFL 4|2014 USA FDA Developments: Food Code 2013 and Proposed Trans Fat Determination Margaret Rosso Grossman* I. Food Code 2013 and Food Code Reference System Since 1993, the US Food and Drug Administration has published a Food Code, now updated every four years. In November 2013, the

Development of a Fully-Automated Monte Carlo Burnup Code Monteburns

International Nuclear Information System (INIS)

Poston, D.I.; Trellue, H.R.

1999-01-01

Several computer codes have been developed to perform nuclear burnup calculations over the past few decades. In addition, because of advances in computer technology, it recently has become more desirable to use Monte Carlo techniques for such problems. Monte Carlo techniques generally offer two distinct advantages over discrete ordinate methods: (1) the use of continuous energy cross sections and (2) the ability to model detailed, complex, three-dimensional (3-D) geometries. These advantages allow more accurate burnup results to be obtained, provided that the user possesses the required computing power (which is required for discrete ordinate methods as well). Several linkage codes have been written that combine a Monte Carlo N-particle transport code (such as MCNP TM ) with a radioactive decay and burnup code. This paper describes one such code that was written at Los Alamos National Laboratory: monteburns. Monteburns links MCNP with the isotope generation and depletion code ORIGEN2. The basis for the development of monteburns was the need for a fully automated code that could perform accurate burnup (and other) calculations for any 3-D system (accelerator-driven or a full reactor core). Before the initial development of monteburns, a list of desired attributes was made and is given below. o The code should be fully automated (that is, after the input is set up, no further user interaction is required). . The code should allow for the irradiation of several materials concurrently (each material is evaluated collectively in MCNP and burned separately in 0RIGEN2). o The code should allow the transfer of materials (shuffling) between regions in MCNP. . The code should allow any materials to be added or removed before, during, or after each step in an automated fashion. . The code should not require the user to provide input for 0RIGEN2 and should have minimal MCNP input file requirements (other than a working MCNP deck). . The code should be relatively easy to use

Development and verification of a coupled code system RETRAN-MASTER-TORC

International Nuclear Information System (INIS)

Cho, J.Y.; Song, J.S.; Joo, H.G.; Zee, S.Q.

2004-01-01

Recently, coupled thermal-hydraulics (T-H) and three-dimensional kinetics codes have been widely used for the best-estimate simulations such as the main steam line break (MSLB) and locked rotor problems. This work is to develop and verify one of such codes by coupling the system T-H code RETRAN, the 3-D kinetics code MASTER and sub-channel analysis code TORC. The MASTER code has already been applied to such simulations after coupling with the MARS or RETRAN-3D multi-dimensional system T-H codes. The MASTER code contains a sub-channel analysis code COBRA-III C/P, and the coupled systems MARSMASTER-COBRA and RETRAN-MASTER-COBRA had been already developed and verified. With these previous studies, a new coupled system of RETRAN-MASTER-TORC is to be developed and verified for the standard best-estimate simulation code package in Korea. The TORC code has already been applied to the thermal hydraulics design of the several ABB/CE type plants and Korean Standard Nuclear Power Plants (KSNP). This justifies the choice of TORC rather than COBRA. Because the coupling between RETRAN and MASTER codes are already established and verified, this work is simplified to couple the TORC sub-channel T-H code with the MASTER neutronics code. The TORC code is a standalone code that solves the T-H equations for a given core problem from reading the input file and finally printing the converged solutions. However, in the coupled system, because TORC receives the pin power distributions from the neutronics code MASTER and transfers the T-H results to MASTER iteratively, TORC needs to be controlled by the MASTER code and does not need to solve the given problem completely at each iteration step. By this reason, the coupling of the TORC code with the MASTER code requires several modifications in the I/O treatment, flow iteration and calculation logics. The next section of this paper describes the modifications in the TORC code. The TORC control logic of the MASTER code is then followed. The

Development and Verification of Behavior of Tritium Analytic Code (BOTANIC)

International Nuclear Information System (INIS)

Park, Min Young; Kim, Eung Soo

2014-01-01

VHTR, one of the Generation IV reactor concepts, has a relatively high operation temperature and is usually suggested as a heat source for many industrial processes, including hydrogen production process. Thus, it is vital to trace tritium behavior in the VHTR system and the potential permeation rate to the industrial process. In other words, tritium is a crucial issue in terms of safety in the fission reactor system. Therefore, it is necessary to understand the behavior of tritium and the development of the tool to enable this is vital.. In this study, a Behavior of Tritium Analytic Code (BOTANIC) an analytic tool which is capable of analyzing tritium behavior is developed using a chemical process code called gPROMS. BOTANIC was then further verified using the analytic solutions and benchmark codes such as Tritium Permeation Analysis Code (TPAC) and COMSOL. In this study, the Behavior of Tritium Analytic Code, BOTANIC, has been developed using a chemical process code called gPROMS. The code has several distinctive features including non-diluted assumption, flexible applications and adoption of distributed permeation model. Due to these features, BOTANIC has the capability to analyze a wide range of tritium level systems and has a higher accuracy as it has the capacity to solve distributed models. BOTANIC was successfully developed and verified using analytical solution and the benchmark code calculation result. The results showed very good agreement with the analytical solutions and the calculation results of TPAC and COMSOL. Future work will be focused on the total system verification

Reactor Systems Technology Division code development and configuration/quality control procedures

International Nuclear Information System (INIS)

Johnson, E.C.

1985-06-01

Procedures are prescribed for executing a code development task and implementing the resulting coding in an official version of a computer code. The responsibilities of the project manager, development staff members, and the Code Configuration/Quality Control Group are defined. Examples of forms, logs, computer job control language, and suggested outlines for reports associated with software production and implementation are included in Appendix A. 1 raf., 2 figs

Theoretical Atomic Physics code development IV: LINES, A code for computing atomic line spectra

International Nuclear Information System (INIS)

Abdallah, J. Jr.; Clark, R.E.H.

1988-12-01

A new computer program, LINES, has been developed for simulating atomic line emission and absorption spectra using the accurate fine structure energy levels and transition strengths calculated by the (CATS) Cowan Atomic Structure code. Population distributions for the ion stages are obtained in LINES by using the Local Thermodynamic Equilibrium (LTE) model. LINES is also useful for displaying the pertinent atomic data generated by CATS. This report describes the use of LINES. Both CATS and LINES are part of the Theoretical Atomic PhysicS (TAPS) code development effort at Los Alamos. 11 refs., 9 figs., 1 tab

On transform coding tools under development for VP10

Science.gov (United States)

Parker, Sarah; Chen, Yue; Han, Jingning; Liu, Zoe; Mukherjee, Debargha; Su, Hui; Wang, Yongzhe; Bankoski, Jim; Li, Shunyao

2016-09-01

Google started the WebM Project in 2010 to develop open source, royaltyfree video codecs designed specifically for media on the Web. The second generation codec released by the WebM project, VP9, is currently served by YouTube, and enjoys billions of views per day. Realizing the need for even greater compression efficiency to cope with the growing demand for video on the web, the WebM team embarked on an ambitious project to develop a next edition codec, VP10, that achieves at least a generational improvement in coding efficiency over VP9. Starting from VP9, a set of new experimental coding tools have already been added to VP10 to achieve decent coding gains. Subsequently, Google joined a consortium of major tech companies called the Alliance for Open Media to jointly develop a new codec AV1. As a result, the VP10 effort is largely expected to merge with AV1. In this paper, we focus primarily on new tools in VP10 that improve coding of the prediction residue using transform coding techniques. Specifically, we describe tools that increase the flexibility of available transforms, allowing the codec to handle a more diverse range or residue structures. Results are presented on a standard test set.

SWAAM-code development and verification and application to steam generator designs

International Nuclear Information System (INIS)

Shin, Y.W.; Valentin, R.A.

1990-01-01

This paper describes the family of SWAAM codes which were developed by Argonne National Laboratory to analyze the effects of sodium-water reactions on LMR steam generators. The SWAAM codes were developed as design tools for analyzing various phenomena related to steam generator leaks and the resulting thermal and hydraulic effects on the steam generator and the intermediate heat transport system (IHTS). The paper discusses the theoretical foundations and numerical treatments on which the codes are based, followed by a description of code capabilities and limitations, verification of the codes and applications to steam generator and IHTS designs. 25 refs., 14 figs

Qualifying codes under software quality assurance: Two examples as guidelines for codes that are existing or under development

Energy Technology Data Exchange (ETDEWEB)

Mangold, D.

1993-05-01

Software quality assurance is an area of concem for DOE, EPA, and other agencies due to the poor quality of software and its documentation they have received in the past. This report briefly summarizes the software development concepts and terminology increasingly employed by these agencies and provides a workable approach to scientific programming under the new requirements. Following this is a practical description of how to qualify a simulation code, based on a software QA plan that has been reviewed and officially accepted by DOE/OCRWM. Two codes have recently been baselined and qualified, so that they can be officially used for QA Level 1 work under the DOE/OCRWM QA requirements. One of them was baselined and qualified within one week. The first of the codes was the multi-phase multi-component flow code TOUGH version 1, an already existing code, and the other was a geochemistry transport code STATEQ that was under development The way to accomplish qualification for both types of codes is summarized in an easy-to-follow step-by step fashion to illustrate how to baseline and qualify such codes through a relatively painless procedure.

Qualifying codes under software quality assurance: Two examples as guidelines for codes that are existing or under development

International Nuclear Information System (INIS)

Mangold, D.

1993-05-01

Software quality assurance is an area of concern for DOE, EPA, and other agencies due to the poor quality of software and its documentation they have received in the past. This report briefly summarizes the software development concepts and terminology increasingly employed by these agencies and provides a workable approach to scientific programming under the new requirements. Following this is a practical description of how to qualify a simulation code, based on a software QA plan that has been reviewed and officially accepted by DOE/OCRWM. Two codes have recently been baselined and qualified, so that they can be officially used for QA Level 1 work under the DOE/OCRWM QA requirements. One of them was baselined and qualified within one week. The first of the codes was the multi-phase multi-component flow code TOUGH version 1, an already existing code, and the other was a geochemistry transport code STATEQ that was under development The way to accomplish qualification for both types of codes is summarized in an easy-to-follow step-by step fashion to illustrate how to baseline and qualify such codes through a relatively painless procedure

Development of fast and accurate Monte Carlo code MVP

International Nuclear Information System (INIS)

Mori, Takamasa

2001-01-01

The development work of fast and accurate Monte Carlo code MVP has started at JAERI in late 80s. From the beginning, the code was designed to utilize vector supercomputers and achieved higher computation speed by a factor of 10 or more compared with conventional codes. In 1994, the first version of MVP was released together with cross section libraries based on JENDL-3.1 and JENDL-3.2. In 1996, minor revision was made by adding several functions such as treatments of ENDF-B6 file 6 data, time dependent problem, and so on. Since 1996, several works have been carried out for the next version of MVP. The main works are (1) the development of continuous energy Monte Carlo burn-up calculation code MVP-BURN, (2) the development of a system to generate cross section libraries at arbitrary temperature, and (3) the study on error estimations and their biases in Monte Carlo eigenvalue calculations. This paper summarizes the main features of MVP, results of recent studies and future plans for MVP. (author)

Development of throughflow calculation code for axial flow compressors

International Nuclear Information System (INIS)

Kim, Ji Hwan; Kim, Hyeun Min; No, Hee Cheon

2005-01-01

The power conversion systems of the current HTGRs are based on closed Brayton cycle and major concern is thermodynamic performance of the axial flow helium gas turbines. Particularly, the helium compressor has some unique design challenges compared to the air-breathing compressor such as high hub-to-tip ratios throughout the machine and a large number of stages due to the physical property of the helium and thermodynamic cycle. Therefore, it is necessary to develop a design and analysis code for helium compressor that can estimate the design point and off-design performance accurately. KAIST nuclear system laboratory has developed a compressor design and analysis code by means of throughflow calculation and several loss models. This paper presents the outline of the development of a throughflow calculation code and its verification results

Developing and modifying behavioral coding schemes in pediatric psychology: a practical guide.

Science.gov (United States)

Chorney, Jill MacLaren; McMurtry, C Meghan; Chambers, Christine T; Bakeman, Roger

2015-01-01

To provide a concise and practical guide to the development, modification, and use of behavioral coding schemes for observational data in pediatric psychology. This article provides a review of relevant literature and experience in developing and refining behavioral coding schemes. A step-by-step guide to developing and/or modifying behavioral coding schemes is provided. Major steps include refining a research question, developing or refining the coding manual, piloting and refining the coding manual, and implementing the coding scheme. Major tasks within each step are discussed, and pediatric psychology examples are provided throughout. Behavioral coding can be a complex and time-intensive process, but the approach is invaluable in allowing researchers to address clinically relevant research questions in ways that would not otherwise be possible. © The Author 2014. Published by Oxford University Press on behalf of the Society of Pediatric Psychology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Developments in the Generation and Interpretation of Wire Codes (invited paper)

International Nuclear Information System (INIS)

Ebi, K.L.

1999-01-01

Three new developments in the generation and interpretation of wire codes are discussed. First, a method was developed to computer generate wire codes using data gathered from a utility database of the local distribution system and from tax assessor records. This method was used to wire code more than 250,000 residences in the greater Denver metropolitan area. There was an approximate 75% agreement with field wire coding. Other research in Denver suggests that wire codes predict some characteristics of a residence and its neighbourhood, including age, assessed value, street layout and traffic density. A third new development is the case-specular method to study the association between wire codes and childhood cancers. Recent results from applying the method to the Savitz et al and London et al studies suggest that the associations between childhood cancer and VHCC residences were strongest for residences with a backyard rather than street service drop, and for VHCC residences with LCC speculars. (author)

Development of LMR basic design technology - Development of 3-D multi-group nodal kinetics code for liquid metal reactors

Energy Technology Data Exchange (ETDEWEB)

Kim, Myung Hyun [Kyunghee University, Seoul (Korea, Republic of)

1996-07-01

A development project of 3-dimensional kinetics code for ALMR has three level of works. In the first level, a multi-group, nodal kinetics code for the HEX-Z geometry has been developed. A code showed very good results for the static analysis as well as for the kinetics problems. At the second level, a core thermal-hydraulic analysis code was developed for the temperature feedback calculation in ALMR transients analysis. This code is coupled with kinetics code. A sodium property table was programmed and tested to the KAERI data and thermal feedback model was developed and coupled in code. Benchmarking of T/H calculation has been performed and showed fairly good results. At the third level of research work, reactivity feedback model for structure thermal expansion is developed and added to the code. At present, basic model was studied. However, code development in now on going. Benchmarking of this model developed can not be done because of lack of data. 31 refs., 17 tabs., 38 figs. (author)

Application of software to development of reactor-safety codes

International Nuclear Information System (INIS)

Wilburn, N.P.; Niccoli, L.G.

1980-09-01

Over the past two-and-a-half decades, the application of new techniques has reduced hardware cost for digital computer systems and increased computational speed by several orders of magnitude. A corresponding cost reduction in business and scientific software development has not occurred. The same situation is seen for software developed to model the thermohydraulic behavior of nuclear systems under hypothetical accident situations. For all cases this is particularly noted when costs over the total software life cycle are considered. A solution to this dilemma for reactor safety code systems has been demonstrated by applying the software engineering techniques which have been developed over the course of the last few years in the aerospace and business communities. These techniques have been applied recently with a great deal of success in four major projects at the Hanford Engineering Development Laboratory (HEDL): 1) a rewrite of a major safety code (MELT); 2) development of a new code system (CONACS) for description of the response of LMFBR containment to hypothetical accidents, and 3) development of two new modules for reactor safety analysis

Development of 1D Liner Compression Code for IDL

Science.gov (United States)

Shimazu, Akihisa; Slough, John; Pancotti, Anthony

2015-11-01

A 1D liner compression code is developed to model liner implosion dynamics in the Inductively Driven Liner Experiment (IDL) where FRC plasmoid is compressed via inductively-driven metal liners. The driver circuit, magnetic field, joule heating, and liner dynamics calculations are performed at each time step in sequence to couple these effects in the code. To obtain more realistic magnetic field results for a given drive coil geometry, 2D and 3D effects are incorporated into the 1D field calculation through use of correction factor table lookup approach. Commercial low-frequency electromagnetic fields solver, ANSYS Maxwell 3D, is used to solve the magnetic field profile for static liner condition at various liner radius in order to derive correction factors for the 1D field calculation in the code. The liner dynamics results from the code is verified to be in good agreement with the results from commercial explicit dynamics solver, ANSYS Explicit Dynamics, and previous liner experiment. The developed code is used to optimize the capacitor bank and driver coil design for better energy transfer and coupling. FRC gain calculations are also performed using the liner compression data from the code for the conceptual design of the reactor sized system for fusion energy gains.

Development and application of methods to characterize code uncertainty

International Nuclear Information System (INIS)

Wilson, G.E.; Burtt, J.D.; Case, G.S.; Einerson, J.J.; Hanson, R.G.

1985-01-01

The United States Nuclear Regulatory Commission sponsors both international and domestic studies to assess its safety analysis codes. The Commission staff intends to use the results of these studies to quantify the uncertainty of the codes with a statistically based analysis method. Development of the methodology is underway. The Idaho National Engineering Laboratory contributions to the early development effort, and testing of two candidate methods are the subjects of this paper

The development of the code package PERMAK--3D//SC--1

International Nuclear Information System (INIS)

Bolobov, P. A.; Oleksuk, D. A.

2011-01-01

Code package PERMAK-3D//SC-1 was developed for performing pin-by-pin coupled neutronic and thermal hydraulic calculation of the core fragment of seven fuel assemblies and was designed on the basis of 3D multigroup pin-by-pin code PERMAK-3D and 3D (subchannel) thermal hydraulic code SC-1 The code package predicts axial and radial pin-by-pin power distribution and coolant parameters in stimulated region (enthalpies,, velocities,, void fractions,, boiling and DNBR margins).. The report describes some new steps in code package development. Some PERMAK-3D//SC-1 outcomes of WWER calculations are presented in the report. (Authors)

Cooperation of experts' opinion, experiment and computer code development

International Nuclear Information System (INIS)

Wolfert, K.; Hicken, E.

The connection between code development, code assessment and confidence in the analysis of transients will be discussed. In this manner, the major sources of errors in the codes and errors in applications of the codes will be shown. Standard problem results emphasize that, in order to have confidence in licensing statements, the codes must be physically realistic and the code user must be qualified and experienced. We will discuss why there is disagreement between the licensing authority and vendor concerning assessment of the fullfillment of safety goal requirements. The answer to the question lies in the different confidence levels of the assessment of transient analysis. It is expected that a decrease in the disagreement will result from an increased confidence level. Strong efforts will be made to increase this confidence level through improvements in the codes, experiments and related organizational strcutures. Because of the low probability for loss-of-coolant-accidents in the nuclear industry, assessment must rely on analytical techniques and experimental investigations. (orig./HP) [de

Development of parallel Fokker-Planck code ALLAp

International Nuclear Information System (INIS)

Batishcheva, A.A.; Sigmar, D.J.; Koniges, A.E.

1996-01-01

We report on our ongoing development of the 3D Fokker-Planck code ALLA for a highly collisional scrape-off-layer (SOL) plasma. A SOL with strong gradients of density and temperature in the spatial dimension is modeled. Our method is based on a 3-D adaptive grid (in space, magnitude of the velocity, and cosine of the pitch angle) and a second order conservative scheme. Note that the grid size is typically 100 x 257 x 65 nodes. It was shown in our previous work that only these capabilities make it possible to benchmark a 3D code against a spatially-dependent self-similar solution of a kinetic equation with the Landau collision term. In the present work we show results of a more precise benchmarking against the exact solutions of the kinetic equation using a new parallel code ALLAp with an improved method of parallelization and a modified boundary condition at the plasma edge. We also report first results from the code parallelization using Message Passing Interface for a Massively Parallel CRI T3D platform. We evaluate the ALLAp code performance versus the number of T3D processors used and compare its efficiency against a Work/Data Sharing parallelization scheme and a workstation version

Development of chemical equilibrium analysis code 'CHEEQ'

International Nuclear Information System (INIS)

Nagai, Shuichiro

2006-08-01

'CHEEQ' code which calculates the partial pressure and the mass of the system consisting of ideal gas and pure condensed phase compounds, was developed. Characteristics of 'CHEEQ' code are as follows. All the chemical equilibrium equations were described by the formation reactions from the mono-atomic gases in order to simplify the code structure and input preparation. Chemical equilibrium conditions, Σν i μ i =0 for the gaseous compounds and precipitated condensed phase compounds and Σν i μ i > 0 for the non-precipitated condensed phase compounds, were applied. Where, ν i and μ i are stoichiometric coefficient and chemical potential of component i. Virtual solid model was introduced to perform the calculation of constant partial pressure condition. 'CHEEQ' was consisted of following 3 parts, (1) analysis code, zc132. f. (2) thermodynamic data base, zmdb01 and (3) input data file, zindb. 'CHEEQ' code can calculate the system which consisted of elements (max.20), condensed phase compounds (max.100) and gaseous compounds. (max.200). Thermodynamic data base, zmdb01 contains about 1000 elements and compounds, and 200 of them were Actinide elements and their compounds. This report describes the basic equations, the outline of the solution procedure and instructions to prepare the input data and to evaluate the calculation results. (author)

Development of code PRETOR for stellarator simulation

International Nuclear Information System (INIS)

Dies, J.; Fontanet, J.; Fontdecaba, J.M.; Castejon, F.; Alejandre, C.

1998-01-01

The Department de Fisica i Enginyeria Nuclear (DFEN) of the UPC has some experience in the development of the transport code PRETOR. This code has been validated with shots of DIII-D, JET and TFTR, it has also been used in the simulation of operational scenarios of ITER fast burnt termination. Recently, the association EURATOM-CIEMAT has started the operation of the TJ-II stellarator. Due to the need of validating the results given by others transport codes applied to stellarators and because all of them made some approximations, as a averaging magnitudes in each magnetic surface, it was thought suitable to adapt the PRETOR code to devices without axial symmetry, like stellarators, which is very suitable for the specific needs of the study of TJ-II. Several modifications are required in PRETOR; the main concerns to the models of: magnetic equilibrium, geometry and transport of energy and particles. In order to solve the complex magnetic equilibrium geometry the powerful numerical code VMEC has been used. This code gives the magnetic surface shape as a Fourier series in terms of the harmonics (m,n). Most of the geometric magnitudes are also obtained from the VMEC results file. The energy and particle transport models will be replaced by other phenomenological models that are better adapted to stellarator simulation. Using the proposed models, it is pretended to reproduce experimental data available from present stellarators, given especial attention to the TJ-II of the association EURATOM-CIEMAT. (Author)

Multiple application coded switch development report

International Nuclear Information System (INIS)

Bernal, E.L.; Kestly, J.D.

1979-03-01

The development of the Multiple Application Coded Switch (MACS) and its related controller are documented; the functional and electrical characteristics are described; the interface requirements defined, and a troubleshooting guide provided. The system was designed for the Safe Secure Trailer System used for secure transportation of nuclear material

Development of steam explosion simulation code JASMINE

Energy Technology Data Exchange (ETDEWEB)

Moriyama, Kiyofumi; Yamano, Norihiro; Maruyama, Yu; Kudo, Tamotsu; Sugimoto, Jun [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Nagano, Katsuhiro; Araki, Kazuhiro

1995-11-01

A steam explosion is considered as a phenomenon which possibly threatens the integrity of the containment vessel of a nuclear power plant in a severe accident condition. A numerical calculation code JASMINE (JAeri Simulator for Multiphase INteraction and Explosion) purposed to simulate the whole process of steam explosions has been developed. The premixing model is based on a multiphase flow simulation code MISTRAL by Fuji Research Institute Co. In JASMINE code, the constitutive equations and the flow regime map are modified for the simulation of premixing related phenomena. The numerical solution method of the original code is succeeded, i.e. the basic equations are discretized semi-implicitly, BCGSTAB method is used for the matrix solver to improve the stability and convergence, also TVD scheme is applied to capture a steep phase distribution accurately. Test calculations have been performed for the conditions correspond to the experiments by Gilbertson et al. and Angelini et al. in which mixing of solid particles and water were observed in iso-thermal condition and with boiling, respectively. (author).

Development of steam explosion simulation code JASMINE

International Nuclear Information System (INIS)

Moriyama, Kiyofumi; Yamano, Norihiro; Maruyama, Yu; Kudo, Tamotsu; Sugimoto, Jun; Nagano, Katsuhiro; Araki, Kazuhiro.

1995-11-01

A steam explosion is considered as a phenomenon which possibly threatens the integrity of the containment vessel of a nuclear power plant in a severe accident condition. A numerical calculation code JASMINE (JAeri Simulator for Multiphase INteraction and Explosion) purposed to simulate the whole process of steam explosions has been developed. The premixing model is based on a multiphase flow simulation code MISTRAL by Fuji Research Institute Co. In JASMINE code, the constitutive equations and the flow regime map are modified for the simulation of premixing related phenomena. The numerical solution method of the original code is succeeded, i.e. the basic equations are discretized semi-implicitly, BCGSTAB method is used for the matrix solver to improve the stability and convergence, also TVD scheme is applied to capture a steep phase distribution accurately. Test calculations have been performed for the conditions correspond to the experiments by Gilbertson et al. and Angelini et al. in which mixing of solid particles and water were observed in iso-thermal condition and with boiling, respectively. (author)

Present status of transport code development based on Monte Carlo method

International Nuclear Information System (INIS)

Nakagawa, Masayuki

1985-01-01

The present status of development in Monte Carlo code is briefly reviewed. The main items are the followings; Application fields, Methods used in Monte Carlo code (geometry spectification, nuclear data, estimator and variance reduction technique) and unfinished works, Typical Monte Carlo codes and Merits of continuous energy Monte Carlo code. (author)

Python-Assisted MODFLOW Application and Code Development

Science.gov (United States)

Langevin, C.

2013-12-01

The U.S. Geological Survey (USGS) has a long history of developing and maintaining free, open-source software for hydrological investigations. The MODFLOW program is one of the most popular hydrologic simulation programs released by the USGS, and it is considered to be the most widely used groundwater flow simulation code. MODFLOW was written using a modular design and a procedural FORTRAN style, which resulted in code that could be understood, modified, and enhanced by many hydrologists. The code is fast, and because it uses standard FORTRAN it can be run on most operating systems. Most MODFLOW users rely on proprietary graphical user interfaces for constructing models and viewing model results. Some recent efforts, however, have focused on construction of MODFLOW models using open-source Python scripts. Customizable Python packages, such as FloPy (https://code.google.com/p/flopy), can be used to generate input files, read simulation results, and visualize results in two and three dimensions. Automating this sequence of steps leads to models that can be reproduced directly from original data and rediscretized in space and time. Python is also being used in the development and testing of new MODFLOW functionality. New packages and numerical formulations can be quickly prototyped and tested first with Python programs before implementation in MODFLOW. This is made possible by the flexible object-oriented design capabilities available in Python, the ability to call FORTRAN code from Python, and the ease with which linear systems of equations can be solved using SciPy, for example. Once new features are added to MODFLOW, Python can then be used to automate comprehensive regression testing and ensure reliability and accuracy of new versions prior to release.

Development of thermal hydraulic models for the reliable regulatory auditing code

Energy Technology Data Exchange (ETDEWEB)

Chung, B. D.; Song, C. H.; Lee, Y. J.; Kwon, T. S.; Lee, S. W. [Korea Automic Energy Research Institute, Taejon (Korea, Republic of)

2004-02-15

The objective of this project is to develop thermal hydraulic models for use in improving the reliability of the regulatory auditing codes. The current year fall under the second step of the 3 year project, and the main researches were focused on the development of downcorner boiling model. During the current year, the bubble stream model of downcorner has been developed and installed in he auditing code. The model sensitivity analysis has been performed for APR1400 LBLOCA scenario using the modified code. The preliminary calculation has been performed for the experimental test facility using FLUENT and MARS code. The facility for air bubble experiment has been installed. The thermal hydraulic phenomena for VHTR and super critical reactor have been identified for the future application and model development.

Safety, codes and standards for hydrogen installations. Metrics development and benchmarking

Energy Technology Data Exchange (ETDEWEB)

Harris, Aaron P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dedrick, Daniel E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); LaFleur, Angela Christine [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); San Marchi, Christopher W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2014-04-01

Automakers and fuel providers have made public commitments to commercialize light duty fuel cell electric vehicles and fueling infrastructure in select US regions beginning in 2014. The development, implementation, and advancement of meaningful codes and standards is critical to enable the effective deployment of clean and efficient fuel cell and hydrogen solutions in the energy technology marketplace. Metrics pertaining to the development and implementation of safety knowledge, codes, and standards are important to communicate progress and inform future R&D investments. This document describes the development and benchmarking of metrics specific to the development of hydrogen specific codes relevant for hydrogen refueling stations. These metrics will be most useful as the hydrogen fuel market transitions from pre-commercial to early-commercial phases. The target regions in California will serve as benchmarking case studies to quantify the success of past investments in research and development supporting safety codes and standards R&D.

Development and validation of the ENIGMA code for MOX fuel performance modelling

International Nuclear Information System (INIS)

Palmer, I.; Rossiter, G.; White, R.J.

2000-01-01

The ENIGMA fuel performance code has been under development in the UK since the mid-1980s with contributions made by both the fuel vendor (BNFL) and the utility (British Energy). In recent years it has become the principal code for UO 2 fuel licensing for both PWR and AGR reactor systems in the UK and has also been used by BNFL in support of overseas UO 2 and MOX fuel business. A significant new programme of work has recently been initiated by BNFL to further develop the code specifically for MOX fuel application. Model development is proceeding hand in hand with a major programme of MOX fuel testing and PIE studies, with the objective of producing a fuel modelling code suitable for mechanistic analysis, as well as for licensing applications. This paper gives an overview of the model developments being undertaken and of the experimental data being used to underpin and to validate the code. The paper provides a summary of the code development programme together with specific examples of new models produced. (author)

Development of the PRO-LOCA Probabilistic Fracture Mechanics Code, MERIT Final Report

International Nuclear Information System (INIS)

Scott, Paul; Kurth, Robert; Cox, Andrew; Olson, Rick; Rudland, Dave

2010-12-01

The MERIT project has been an internationally financed program with the main purpose of developing probabilistic models for piping failure of nuclear components and to include these models in a probabilistic code named PRO-LOCA. The principal objective of the project has been to develop probabilistic models for piping failure of nuclear components and to include these models in a probabilistic code. The MERIT program has produced a code named PRO-LOCA with the following features: - Crack initiation models for fatigue or stress corrosion cracking for previously unflawed material. - Subcritical crack growth models for fatigue and stress corrosion cracking for both initiated and pre-existing circumferential defects. - Models for flaw detection by inspections and leak detection. - Crack stability. The PRO-LOCA code can thus predict the leak or break frequency for the whole sequence of initiation, subcritical crack growth until wall penetration and leakage, instability of the through-wall crack (pipe rupture). The outcome of the PRO-LOCA code are a sequence of failure frequencies which represents the probability of surface crack developing, a through-wall crack developing and six different sizes of crack opening areas corresponding to different leak flow rates or LOCA categories. Note that the level of quality assurance of the PRO-LOCA code is such that the code in its current state of development is considered to be more of a research code than a regulatory tool.

Development of the PRO-LOCA Probabilistic Fracture Mechanics Code, MERIT Final Report

Energy Technology Data Exchange (ETDEWEB)

Scott, Paul; Kurth, Robert; Cox, Andrew; Olson, Rick (Battelle Columbus (United States)); Rudland, Dave (Nuclear Regulatory Commission (United States))

2010-12-15

The MERIT project has been an internationally financed program with the main purpose of developing probabilistic models for piping failure of nuclear components and to include these models in a probabilistic code named PRO-LOCA. The principal objective of the project has been to develop probabilistic models for piping failure of nuclear components and to include these models in a probabilistic code. The MERIT program has produced a code named PRO-LOCA with the following features: - Crack initiation models for fatigue or stress corrosion cracking for previously unflawed material. - Subcritical crack growth models for fatigue and stress corrosion cracking for both initiated and pre-existing circumferential defects. - Models for flaw detection by inspections and leak detection. - Crack stability. The PRO-LOCA code can thus predict the leak or break frequency for the whole sequence of initiation, subcritical crack growth until wall penetration and leakage, instability of the through-wall crack (pipe rupture). The outcome of the PRO-LOCA code are a sequence of failure frequencies which represents the probability of surface crack developing, a through-wall crack developing and six different sizes of crack opening areas corresponding to different leak flow rates or LOCA categories. Note that the level of quality assurance of the PRO-LOCA code is such that the code in its current state of development is considered to be more of a research code than a regulatory tool.

Theoretical atomic physics code development I: CATS: Cowan Atomic Structure Code

International Nuclear Information System (INIS)

Abdallah, J. Jr.; Clark, R.E.H.; Cowan, R.D.

1988-12-01

An adaptation of R.D. Cowan's Atomic Structure program, CATS, has been developed as part of the Theoretical Atomic Physics (TAPS) code development effort at Los Alamos. CATS has been designed to be easy to run and to produce data files that can interface with other programs easily. The CATS produced data files currently include wave functions, energy levels, oscillator strengths, plane-wave-Born electron-ion collision strengths, photoionization cross sections, and a variety of other quantities. This paper describes the use of CATS. 10 refs

Recent developments in the Los Alamos radiation transport code system

International Nuclear Information System (INIS)

Forster, R.A.; Parsons, K.

1997-01-01

A brief progress report on updates to the Los Alamos Radiation Transport Code System (LARTCS) for solving criticality and fixed-source problems is provided. LARTCS integrates the Diffusion Accelerated Neutral Transport (DANT) discrete ordinates codes with the Monte Carlo N-Particle (MCNP) code. The LARCTS code is being developed with a graphical user interface for problem setup and analysis. Progress in the DANT system for criticality applications include a two-dimensional module which can be linked to a mesh-generation code and a faster iteration scheme. Updates to MCNP Version 4A allow statistical checks of calculated Monte Carlo results

Development of Nuclear Energy Security Code

International Nuclear Information System (INIS)

Shimamura, Takehisa; Suzuki, Atsuyuki; Okubo, Hiroo; Kikuchi, Masahiro.

1990-01-01

In establishing of the nuclear fuel cycle in Japan that have a vulnerability in own energy structure, an effectiveness of energy security should be taken into account as well as an economy based on the balance of supply and demand of nuclear fuels. NMCC develops the 'Nuclear Energy Security Code' which was able to evaluate the effectiveness of energy security. Evaluation method adopted in this code is 'Import Premium' which was proposed in 'World Oil', EMF Report 6. The viewpoints of evaluation are as follows: 1. How much uranium fuel quantity can be reduced by using plutonium fuel? 2. How much a sudden rise of fuel cost can be absorbed by establishing the plutonium cycle beforehand the energy crisis? (author)

Perspectives on the development of next generation reactor systems safety analysis codes

International Nuclear Information System (INIS)

Zhang, H.

2015-01-01

'Full text:' Existing reactor system analysis codes, such as RELAP5-3D and TRAC, have gained worldwide success in supporting reactor safety analyses, as well as design and licensing of new reactors. These codes are important assets to the nuclear engineering research community, as well as to the nuclear industry. However, most of these codes were originally developed during the 1970s', and it becomes necessary to develop next-generation reactor system analysis codes for several reasons. Firstly, as new reactor designs emerge, there are new challenges emerging in numerical simulations of reactor systems such as long lasting transients and multi-physics phenomena. These new requirements are beyond the range of applicability of the existing system analysis codes. Advanced modeling and numerical methods must be taken into consideration to improve the existing capabilities. Secondly, by developing next-generation reactor system analysis codes, the knowledge (know how) in two phase flow modeling and the highly complex constitutive models will be transferred to the young generation of nuclear engineers. And thirdly, all computer codes have limited shelf life. It becomes less and less cost-effective to maintain a legacy code, due to the fast change of computer hardware and software environment. There are several critical perspectives in terms of developing next-generation reactor system analysis codes: 1) The success of the next-generation codes must be built upon the success of the existing codes. The knowledge of the existing codes, not just simply the manuals and codes, but knowing why and how, must be transferred to the next-generation codes. The next-generation codes should encompass the capability of the existing codes. The shortcomings of existing codes should be identified, understood, and properly categorized, for example into model deficiencies or numerical method deficiencies. 2) State-of-the-art models and numerical methods must be considered to

Perspectives on the development of next generation reactor systems safety analysis codes

Energy Technology Data Exchange (ETDEWEB)

Zhang, H., E-mail: Hongbin.Zhang@inl.gov [Idaho National Laboratory, Idaho Falls, ID (United States)

2015-07-01

'Full text:' Existing reactor system analysis codes, such as RELAP5-3D and TRAC, have gained worldwide success in supporting reactor safety analyses, as well as design and licensing of new reactors. These codes are important assets to the nuclear engineering research community, as well as to the nuclear industry. However, most of these codes were originally developed during the 1970s', and it becomes necessary to develop next-generation reactor system analysis codes for several reasons. Firstly, as new reactor designs emerge, there are new challenges emerging in numerical simulations of reactor systems such as long lasting transients and multi-physics phenomena. These new requirements are beyond the range of applicability of the existing system analysis codes. Advanced modeling and numerical methods must be taken into consideration to improve the existing capabilities. Secondly, by developing next-generation reactor system analysis codes, the knowledge (know how) in two phase flow modeling and the highly complex constitutive models will be transferred to the young generation of nuclear engineers. And thirdly, all computer codes have limited shelf life. It becomes less and less cost-effective to maintain a legacy code, due to the fast change of computer hardware and software environment. There are several critical perspectives in terms of developing next-generation reactor system analysis codes: 1) The success of the next-generation codes must be built upon the success of the existing codes. The knowledge of the existing codes, not just simply the manuals and codes, but knowing why and how, must be transferred to the next-generation codes. The next-generation codes should encompass the capability of the existing codes. The shortcomings of existing codes should be identified, understood, and properly categorized, for example into model deficiencies or numerical method deficiencies. 2) State-of-the-art models and numerical methods must be considered to

Open-Source Development of the Petascale Reactive Flow and Transport Code PFLOTRAN

Science.gov (United States)

Hammond, G. E.; Andre, B.; Bisht, G.; Johnson, T.; Karra, S.; Lichtner, P. C.; Mills, R. T.

2013-12-01

Open-source software development has become increasingly popular in recent years. Open-source encourages collaborative and transparent software development and promotes unlimited free redistribution of source code to the public. Open-source development is good for science as it reveals implementation details that are critical to scientific reproducibility, but generally excluded from journal publications. In addition, research funds that would have been spent on licensing fees can be redirected to code development that benefits more scientists. In 2006, the developers of PFLOTRAN open-sourced their code under the U.S. Department of Energy SciDAC-II program. Since that time, the code has gained popularity among code developers and users from around the world seeking to employ PFLOTRAN to simulate thermal, hydraulic, mechanical and biogeochemical processes in the Earth's surface/subsurface environment. PFLOTRAN is a massively-parallel subsurface reactive multiphase flow and transport simulator designed from the ground up to run efficiently on computing platforms ranging from the laptop to leadership-class supercomputers, all from a single code base. The code employs domain decomposition for parallelism and is founded upon the well-established and open-source parallel PETSc and HDF5 frameworks. PFLOTRAN leverages modern Fortran (i.e. Fortran 2003-2008) in its extensible object-oriented design. The use of this progressive, yet domain-friendly programming language has greatly facilitated collaboration in the code's software development. Over the past year, PFLOTRAN's top-level data structures were refactored as Fortran classes (i.e. extendible derived types) to improve the flexibility of the code, ease the addition of new process models, and enable coupling to external simulators. For instance, PFLOTRAN has been coupled to the parallel electrical resistivity tomography code E4D to enable hydrogeophysical inversion while the same code base can be used as a third

Development and validation of sodium fire analysis code ASSCOPS

International Nuclear Information System (INIS)

Ohno, Shuji

2001-01-01

A version 2.1 of the ASSCOPS sodium fire analysis code was developed to evaluate the thermal consequences of a sodium leak and consequent fire in LMFBRs. This report describes the computational models and the validation studies using the code. The ASSCOPS calculates sodium droplet and pool fire, and consequential heat/mass transfer behavior. Analyses of sodium pool or spray fire experiments confirmed that this code and parameters used in the validation studies gave valid results on the thermal consequences of sodium leaks and fires. (author)

Development of statistical analysis code for meteorological data (W-View)

International Nuclear Information System (INIS)

Tachibana, Haruo; Sekita, Tsutomu; Yamaguchi, Takenori

2003-03-01

A computer code (W-View: Weather View) was developed to analyze the meteorological data statistically based on 'the guideline of meteorological statistics for the safety analysis of nuclear power reactor' (Nuclear Safety Commission on January 28, 1982; revised on March 29, 2001). The code gives statistical meteorological data to assess the public dose in case of normal operation and severe accident to get the license of nuclear reactor operation. This code was revised from the original code used in a large office computer code to enable a personal computer user to analyze the meteorological data simply and conveniently and to make the statistical data tables and figures of meteorology. (author)

Development of REFLA/TRAC code for engineering work station

International Nuclear Information System (INIS)

Ohnuki, Akira; Akimoto, Hajime; Murao, Yoshio

1994-03-01

The REFLA/TRAC code is a best-estimate code which is expected to check reactor safety analysis codes for light water reactors (LWRs) and to perform accident analyses for LWRs and also for an advanced LWR. Therefore, a high predictive capability is required and the assessment of each physical model becomes important because the models govern the predictive capability. In the case of the assessment of three-dimensional models in REFLA/TRAC code, a conventional large computer is being used and it is difficult to perform the assessment efficiently because the turnaround time for the calculation and the analysis is long. Then, a REFLA/TRAC code which can run on an engineering work station (EWS) was developed. Calculational speed of the current EWS is the same order as that of large computers and the EWS has an excellent function for multidimensional graphical drawings. Besides, the plotting processors for X-Y drawing and for two-dimensional graphical drawing were developed in order to perform efficient analyses for three-dimensional calculations. In future, we can expect that the assessment of three-dimensional models becomes more efficient by introducing an EWS with higher calculational speed and with improved graphical drawings. In this report, each outline for the following three programs is described: (1) EWS version of REFLA/TRAC code, (2) Plot processor for X-Y drawing and (3) Plot processor for two-dimensional graphical drawing. (author)

Development of particle and heavy ion transport code system

International Nuclear Information System (INIS)

Niita, Koji

2004-01-01

Particle and heavy ion transport code system (PHITS) is 3 dimension general purpose Monte Carlo simulation codes for description of transport and reaction of particle and heavy ion in materials. It is developed on the basis of NMTC/JAM for design and safety of J-PARC. What is PHITS, it's physical process, physical models and development process of PHITC code are described. For examples of application, evaluation of neutron optics, cancer treatment by heavy particle ray and cosmic radiation are stated. JAM and JQMD model are used as the physical model. Neutron motion in six polar magnetic field and gravitational field, PHITC simulation of trace of C 12 beam and secondary neutron track of small model of cancer treatment device in HIMAC and neutron flux in Space Shuttle are explained. (S.Y.)

Development of CAP code for nuclear power plant containment: Lumped model

Energy Technology Data Exchange (ETDEWEB)

Hong, Soon Joon, E-mail: sjhong90@fnctech.com [FNC Tech. Co. Ltd., Heungdeok 1 ro 13, Giheung-gu, Yongin-si, Gyeonggi-do 446-908 (Korea, Republic of); Choo, Yeon Joon; Hwang, Su Hyun; Lee, Byung Chul [FNC Tech. Co. Ltd., Heungdeok 1 ro 13, Giheung-gu, Yongin-si, Gyeonggi-do 446-908 (Korea, Republic of); Ha, Sang Jun [Central Research Institute, Korea Hydro & Nuclear Power Company, Ltd., 70, 1312-gil, Yuseong-daero, Yuseong-gu, Daejeon 305-343 (Korea, Republic of)

2015-09-15

Highlights: • State-of-art containment analysis code, CAP, has been developed. • CAP uses 3-field equations, water level oriented upwind scheme, local head model. • CAP has a function of linked calculation with reactor coolant system code. • CAP code assessments showed appropriate prediction capabilities. - Abstract: CAP (nuclear Containment Analysis Package) code has been developed in Korean nuclear society for the analysis of nuclear containment thermal hydraulic behaviors including pressure and temperature trends and hydrogen concentration. Lumped model of CAP code uses 2-phase, 3-field equations for fluid behaviors, and has appropriate constitutive equations, 1-dimensional heat conductor model, component models, trip and control models, and special process models. CAP can run in a standalone mode or a linked mode with a reactor coolant system analysis code. The linked mode enables the more realistic calculation of a containment response and is expected to be applicable to a more complicated advanced plant design calculation. CAP code assessments were carried out by gradual approaches: conceptual problems, fundamental phenomena, component and principal phenomena, experimental validation, and finally comparison with other code calculations on the base of important phenomena identifications. The assessments showed appropriate prediction capabilities of CAP.

Development of CAP code for nuclear power plant containment: Lumped model

International Nuclear Information System (INIS)

Hong, Soon Joon; Choo, Yeon Joon; Hwang, Su Hyun; Lee, Byung Chul; Ha, Sang Jun

2015-01-01

Highlights: • State-of-art containment analysis code, CAP, has been developed. • CAP uses 3-field equations, water level oriented upwind scheme, local head model. • CAP has a function of linked calculation with reactor coolant system code. • CAP code assessments showed appropriate prediction capabilities. - Abstract: CAP (nuclear Containment Analysis Package) code has been developed in Korean nuclear society for the analysis of nuclear containment thermal hydraulic behaviors including pressure and temperature trends and hydrogen concentration. Lumped model of CAP code uses 2-phase, 3-field equations for fluid behaviors, and has appropriate constitutive equations, 1-dimensional heat conductor model, component models, trip and control models, and special process models. CAP can run in a standalone mode or a linked mode with a reactor coolant system analysis code. The linked mode enables the more realistic calculation of a containment response and is expected to be applicable to a more complicated advanced plant design calculation. CAP code assessments were carried out by gradual approaches: conceptual problems, fundamental phenomena, component and principal phenomena, experimental validation, and finally comparison with other code calculations on the base of important phenomena identifications. The assessments showed appropriate prediction capabilities of CAP

Development of AGNES, a kinetics code for fissile solutions, 1

International Nuclear Information System (INIS)

Nakajima, Ken; Ohnishi, Nobuaki

1986-01-01

A kinetics code for fissile solutions, AGNES (Accidentally Generated Nuclear Excursion Simulation code), has been developed. This code calculates the radiolytic gas void effect as a reactivity feedback. Physical and calculative models of the radiolytic gas void are summarized and the usage of AGNES is described. In addition, some benchmark calculations were performed and results of calculations show good agreement with those of experiments. (author)

Development of System Based Code: Case Study of Life-Cycle Margin Evaluation

International Nuclear Information System (INIS)

Tai Asayama; Masaki Morishita; Masanori Tashimo

2006-01-01

For a leap of progress in structural deign of nuclear plant components, The late Professor Emeritus Yasuhide Asada proposed the System Based Code. The key concepts of the System Based Code are; (1) life-cycle margin optimization, (2) expansion of technical options as well as combinations of technical options beyond the current codes and standards, and (3) designing to clearly defined target reliabilities. Those concepts are very new to most of the nuclear power plant designers who are naturally obliged to design to current codes and standards; the application of the concepts of the System Based Code to design will lead to entire change of practices that designers have long been accustomed to. On the other hand, experienced designers are supposed to have expertise that can support and accelerate the development of the System Based Code. Therefore, interfacing with experienced designers is of crucial importance for the development of the System Based Code. The authors conducted a survey on the acceptability of the System Based Code concept. The results were analyzed from the possibility of improving structural design both in terms of reliability and cost effectiveness by the introduction of the System Based Code concept. It was concluded that the System Based Code is beneficial for those purposes. Also described is the expertise elicited from the results of the survey that can be reflected to the development of the System Based Code. (authors)

Development of an advanced code system for fast-reactor transient analysis

International Nuclear Information System (INIS)

Konstantin Mikityuk; Sandro Pelloni; Paul Coddington

2005-01-01

FAST (Fast-spectrum Advanced Systems for power production and resource management) is a recently approved PSI activity in the area of fast spectrum core and safety analysis with emphasis on generic developments and Generation IV systems. In frames of the FAST project we will study both statics and transients core physics, reactor system behaviour and safety; related international experiments. The main current goal of the project is to develop unique analytical and code capability for core and safety analysis of critical (and sub-critical) fast spectrum systems with an initial emphasis on a gas cooled fast reactors. A structure of the code system is shown on Fig. 1. The main components of the FAST code system are 1) ERANOS code for preparation of basic x-sections and their partial derivatives; 2) PARCS transient nodal-method multi-group neutron diffusion code for simulation of spatial (3D) neutron kinetics in hexagonal and square geometries; 3) TRAC/AAA code for system thermal hydraulics; 4) FRED transient model for fuel thermal-mechanical behaviour; 5) PVM system as an interface between separate parts of the code system. The paper presents a structure of the code system (Fig. 1), organization of interfaces and data exchanges between main parts of the code system, examples of verification and application of separate codes and the system as a whole. (authors)

Development of safety analysis codes for light water reactor

International Nuclear Information System (INIS)

Akimoto, Masayuki

1985-01-01

An overview is presented of currently used major codes for the prediction of thermohydraulic transients in nuclear power plants. The overview centers on the two-phase fluid dynamics of the coolant system and the assessment of the codes. Some of two-phase phenomena such as phase separation are not still predicted with engineering accuracy. MINCS-PIPE are briefly introduced. The MINCS-PIPE code is to assess constitutive relations and to aid development of various experimental correlations for 1V1T model to 2V2T model. (author)

Development of a new EMP code at LANL

Science.gov (United States)

Colman, J. J.; Roussel-Dupré, R. A.; Symbalisty, E. M.; Triplett, L. A.; Travis, B. J.

2006-05-01

A new code for modeling the generation of an electromagnetic pulse (EMP) by a nuclear explosion in the atmosphere is being developed. The source of the EMP is the Compton current produced by the prompt radiation (γ-rays, X-rays, and neutrons) of the detonation. As a first step in building a multi- dimensional EMP code we have written three kinetic codes, Plume, Swarm, and Rad. Plume models the transport of energetic electrons in air. The Plume code solves the relativistic Fokker-Planck equation over a specified energy range that can include ~ 3 keV to 50 MeV and computes the resulting electron distribution function at each cell in a two dimensional spatial grid. The energetic electrons are allowed to transport, scatter, and experience Coulombic drag. Swarm models the transport of lower energy electrons in air, spanning 0.005 eV to 30 keV. The swarm code performs a full 2-D solution to the Boltzmann equation for electrons in the presence of an applied electric field. Over this energy range the relevant processes to be tracked are elastic scattering, three body attachment, two body attachment, rotational excitation, vibrational excitation, electronic excitation, and ionization. All of these occur due to collisions between the electrons and neutral bodies in air. The Rad code solves the full radiation transfer equation in the energy range of 1 keV to 100 MeV. It includes effects of photo-absorption, Compton scattering, and pair-production. All of these codes employ a spherical coordinate system in momentum space and a cylindrical coordinate system in configuration space. The "z" axis of the momentum and configuration spaces is assumed to be parallel and we are currently also assuming complete spatial symmetry around the "z" axis. Benchmarking for each of these codes will be discussed as well as the way forward towards an integrated modern EMP code.

Recent developments in seismic analysis in the code Aster

International Nuclear Information System (INIS)

Guihot, P.; Devesa, G.; Dumond, A.; Panet, M.; Waeckel, F.

1996-01-01

Progress in the field of seismic qualification and design methods made these last few years allows physical phenomena actually in play to be better considered, while cutting down the conservatism associated with some simplified design methods. So following the change in methods and developing the most advantageous ones among them contributes to the process of the seismic margins assessment and the preparation of new design tools for future series. In this paper, the main developments and improvements in methods which have been made these last two years in the Code Aster, in order to improve seismic calculation methods and seismic margin assessment are presented. The first development relates to making the MISS3D soil structure interaction code available, thanks to an interface made with the Code Aster. The second relates to the possibility of making modal basis time calculations on multi-supported structures by considering local non linearities like impact, friction or squeeze fluid forces. Recent developments in random dynamics and postprocessing devoted to earthquake designs are then mentioned. Three applications of these developments are then ut forward. The first application relates to a test case for soil structure interaction design using MISS3D-Aster coupling. The second is a test case for a multi-supported structure. The last application, more for manufacturing, refers to seismic qualification of Main Live Steam stop valves. First results of the independent validation of the Code Aster seismic design functionalities, which provide and improve the quality of software, are also recalled. (authors)

Development of probabilistic fracture mechanics code PASCAL and user's manual

Energy Technology Data Exchange (ETDEWEB)

Shibata, Katsuyuki; Onizawa, Kunio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Li, Yinsheng; Kato, Daisuke [Fuji Research Institute Corporation, Tokyo (Japan)

2001-03-01

As a part of the aging and structural integrity research for LWR components, a new PFM (Probabilistic Fracture Mechanics) code PASCAL (PFM Analysis of Structural Components in Aging LWR) has been developed since FY1996. This code evaluates the failure probability of an aged reactor pressure vessel subjected to transient loading such as PTS (Pressurized Thermal Shock). The development of the code has been aimed to improve the accuracy and reliability of analysis by introducing new analysis methodologies and algorithms considering the recent development in the fracture mechanics methodologies and computer performance. The code has some new functions in optimized sampling and cell dividing procedure in stratified Monte Carlo simulation, elastic-plastic fracture criterion of R6 method, extension analysis models in semi-elliptical crack, evaluation of effect of thermal annealing and etc. In addition, an input data generator of temperature and stress distribution time histories was also prepared in the code. Functions and performance of the code have been confirmed based on the verification analyses and some case studies on the influence parameters. The present phase of the development will be completed in FY2000. Thus this report provides the user's manual and theoretical background of the code. (author)

Development and assessment of the COBRA/RELAP5 code

Energy Technology Data Exchange (ETDEWEB)

Jeong, Jae Jun; Ha, Kwi Seok; Sim, Seok Ku

1997-04-01

The COBRA/RELAP5 code, a merged version of the COBRA-TF and RELAP5/MOD3.2 codes, has been developed to combine the realistic three-dimensional reactor vessel model of COBRA-TF with RELAP5/MOD3, thus to produce an advanced system analysis code with a multidimensional thermal-hydraulic module. This report provides the integration scheme of the two codes and the results of developmental assessments. These includes single channel tests, manometric flow oscillation problem, THTF Test 105, and LOFT L2-3 large-break loss-of-coolant experiment. From the single channel tests the integration scheme and its implementation were proven to be valid. Other simulation results showed good agreement with the experiments. The computational speed was also satisfactory. So it is confirmed that COBRA/RELAP5 can be a promising tool for analysis of complicated, multidimensional two-phase flow transients. The area of further improvements in the code integration are also identified. This report also serves as a user`s manual for the COBRA/RELAP5 code. (author). 6 tabs., 20 figs., 20 refs.

Development of statistical analysis code for meteorological data (W-View)

Energy Technology Data Exchange (ETDEWEB)

Tachibana, Haruo; Sekita, Tsutomu; Yamaguchi, Takenori [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2003-03-01

A computer code (W-View: Weather View) was developed to analyze the meteorological data statistically based on 'the guideline of meteorological statistics for the safety analysis of nuclear power reactor' (Nuclear Safety Commission on January 28, 1982; revised on March 29, 2001). The code gives statistical meteorological data to assess the public dose in case of normal operation and severe accident to get the license of nuclear reactor operation. This code was revised from the original code used in a large office computer code to enable a personal computer user to analyze the meteorological data simply and conveniently and to make the statistical data tables and figures of meteorology. (author)

Development of Monte Carlo-based pebble bed reactor fuel management code

International Nuclear Information System (INIS)

Setiadipura, Topan; Obara, Toru

2014-01-01

Highlights: • A new Monte Carlo-based fuel management code for OTTO cycle pebble bed reactor was developed. • The double-heterogeneity was modeled using statistical method in MVP-BURN code. • The code can perform analysis of equilibrium and non-equilibrium phase. • Code-to-code comparisons for Once-Through-Then-Out case were investigated. • Ability of the code to accommodate the void cavity was confirmed. - Abstract: A fuel management code for pebble bed reactors (PBRs) based on the Monte Carlo method has been developed in this study. The code, named Monte Carlo burnup analysis code for PBR (MCPBR), enables a simulation of the Once-Through-Then-Out (OTTO) cycle of a PBR from the running-in phase to the equilibrium condition. In MCPBR, a burnup calculation based on a continuous-energy Monte Carlo code, MVP-BURN, is coupled with an additional utility code to be able to simulate the OTTO cycle of PBR. MCPBR has several advantages in modeling PBRs, namely its Monte Carlo neutron transport modeling, its capability of explicitly modeling the double heterogeneity of the PBR core, and its ability to model different axial fuel speeds in the PBR core. Analysis at the equilibrium condition of the simplified PBR was used as the validation test of MCPBR. The calculation results of the code were compared with the results of diffusion-based fuel management PBR codes, namely the VSOP and PEBBED codes. Using JENDL-4.0 nuclide library, MCPBR gave a 4.15% and 3.32% lower k eff value compared to VSOP and PEBBED, respectively. While using JENDL-3.3, MCPBR gave a 2.22% and 3.11% higher k eff value compared to VSOP and PEBBED, respectively. The ability of MCPBR to analyze neutron transport in the top void of the PBR core and its effects was also confirmed

Windows user-friendly code package development for operation of research reactors

International Nuclear Information System (INIS)

Hoang Anh Tuan

1998-01-01

The content of the project was to developed: 1. MS Windows interface to spectral codes like THERMOS, PEACO-COLLIS, GRACE and burn-up code. 2. MS Windows C-language burn-up diffusion hexagonal lattice code. The overall scope of the project was to develop a PC-based MS Windows code package for operation of Dalat research reactor. Various problems relating to neutronic physics like thermalization, resonance treatment, fast spectral treatment, change of isotopic concentration during burn-up time as well as burn-up distribution in the reactor core are considered in parallel to application of informatics technique. The developing process is a subject of the concept of user-friendly interface between end-users and the code package. High level input features through system of icon, menu, dialog box with regard to Common User Access (CUA) convention and sophisticated graphical output in MS Windows environment was used. The user-computer interface is also enhanced by using both keyboard and mouse, which creates a very natural manner for end-user. (author)

A restructuring proposal based on MELCOR for severe accident analysis code development

Energy Technology Data Exchange (ETDEWEB)

Park, Sun Hee; Song, Y. M.; Kim, D. H. [Korea Atomic Energy Research Institute, Taejeon (Korea)

2000-03-01

In order to develop a template based on existing MELCOR code, current data saving and transferring methods used in MELCOR are addressed first. Then a naming convention for the constructed module is suggested and an automatic program to convert old variables into new derived type variables has been developed. Finally, a restructured module for the SPR package has been developed to be applied to MELCOR. The current MELCOR code ensures a fixed-size storage for four different data types, and manages the variable-sized data within the storage limit by storing the data on the stacked packages. It uses pointer to identify the variables between the packages. This technique causes a difficult grasping of the meaning of the variables as well as memory waste. New features of FORTRAN90, however, make it possible to allocate the storage dynamically, and to use the user-defined data type which lead to a restructured module development for the SPR package. An efficient memory treatment and as easy understanding of the code are allowed in this developed module. The validation of the template has been done by comparing the results of the modified code with those from the existing code, and it is confirmed that the results are the same. The template for the SPR package suggested in this report hints the extension of the template to the entire code. It is expected that the template will accelerate the code domestication thanks to direct understanding of each variable and easy implementation of modified or newly developed models. 3 refs., 15 figs., 16 tabs. (Author)

Development and Application of Subchannel Analysis Code Technology for Advanced Reactor Systems

International Nuclear Information System (INIS)

Hwang, Dae Hyun; Seo, K. W.

2006-01-01

A study has been performed for the development and assessment of a subchannel analysis code which is purposed to be used for the analysis of advanced reactor conditions with various configurations of reactor core and several kinds of reactor coolant fluids. The subchannel analysis code was developed on the basis of MATRA code which is being developed at KAERI. A GUI (Graphic User Interface) system was adopted in order to reduce input error and to enhance user convenience. The subchannel code was complemented in the property calculation modules by including various fluids such as heavy liquid metal, gas, refrigerant,and supercritical water. The subchannel code was applied to calculate the local thermal hydraulic conditions inside the non-square test bundles which was employed for the analysis of CHF. The applicability of the subchannel code was evaluated for a high temperature gas cooled reactor condition and supercritical pressure conditions with water and Freon. A subchannel analysis has been conducted for European ADS(Accelerator-Driven subcritical System) with Pb-Bi coolant through the international cooperation work between KAERI and FZK, Germany. In addition, the prediction capability of the subchannel code was evaluated for the subchannel void distribution data by participating an international code benchmark program which was organized by OECD/NRC

Development and Application of Subchannel Analysis Code Technology for Advanced Reactor Systems

Energy Technology Data Exchange (ETDEWEB)

Hwang, Dae Hyun; Seo, K. W

2006-01-15

A study has been performed for the development and assessment of a subchannel analysis code which is purposed to be used for the analysis of advanced reactor conditions with various configurations of reactor core and several kinds of reactor coolant fluids. The subchannel analysis code was developed on the basis of MATRA code which is being developed at KAERI. A GUI (Graphic User Interface) system was adopted in order to reduce input error and to enhance user convenience. The subchannel code was complemented in the property calculation modules by including various fluids such as heavy liquid metal, gas, refrigerant,and supercritical water. The subchannel code was applied to calculate the local thermal hydraulic conditions inside the non-square test bundles which was employed for the analysis of CHF. The applicability of the subchannel code was evaluated for a high temperature gas cooled reactor condition and supercritical pressure conditions with water and Freon. A subchannel analysis has been conducted for European ADS(Accelerator-Driven subcritical System) with Pb-Bi coolant through the international cooperation work between KAERI and FZK, Germany. In addition, the prediction capability of the subchannel code was evaluated for the subchannel void distribution data by participating an international code benchmark program which was organized by OECD/NRC.

Sub-channel/system coupled code development and its application to SCWR-FQT loop

International Nuclear Information System (INIS)

Liu, X.J.; Cheng, X.

2015-01-01

Highlights: • A coupled code is developed for SCWR accident simulation. • The feasibility of the code is shown by application to SCWR-FQT loop. • Some measures are selected by sensitivity analysis. • The peak cladding temperature can be reduced effectively by the proposed measures. - Abstract: In the frame of Super-Critical Reactor In Pipe Test Preparation (SCRIPT) project in China, one of the challenge tasks is to predict the transient performance of SuperCritical Water Reactor-Fuel Qualification Test (SCWR-FQT) loop under some accident conditions. Several thermal–hydraulic codes (system code, sub-channel code) are selected to perform the safety analysis. However, the system code cannot simulate the local behavior of the test bundle, and the sub-channel code is incapable of calculating the whole system behavior of the test loop. Therefore, to combine the merits of both codes, and minimizes their shortcomings, a coupled sub-channel and system code system is developed in this paper. Both of the sub-channel code COBRA-SC and system code ATHLET-SC are adapted to transient analysis of SCWR. Two codes are coupled by data transfer and data adaptation at the interface. In the new developed coupled code, the whole system behavior including safety system characteristic is analyzed by system code ATHLET-SC, whereas the local thermal–hydraulic parameters are predicted by the sub-channel code COBRA-SC. The codes are utilized to get the local thermal–hydraulic parameters in the SCWR-FQT fuel bundle under some accident case (e.g. a flow blockage during LOCA). Some measures to mitigate the accident consequence are proposed by the sensitivity study and trialed to demonstrate their effectiveness in the coupled simulation. The results indicate that the new developed code has good feasibility to transient analysis of supercritical water-cooled test. And the peak cladding temperature caused by blockage in the fuel bundle can be reduced effectively by the safety measures

Sub-channel/system coupled code development and its application to SCWR-FQT loop

Energy Technology Data Exchange (ETDEWEB)

Liu, X.J., E-mail: xiaojingliu@sjtu.edu.cn [School of Nuclear Science and Engineering, Shanghai Jiao Tong University, 800 Dong Chuan Road, Shanghai 200240 (China); Cheng, X. [Institute of Fusion and Reactor Technology, Karlsruhe Institute of Technology, Vincenz-Prießnitz-Str. 3, 76131 Karlsruhe (Germany)

2015-04-15

Highlights: • A coupled code is developed for SCWR accident simulation. • The feasibility of the code is shown by application to SCWR-FQT loop. • Some measures are selected by sensitivity analysis. • The peak cladding temperature can be reduced effectively by the proposed measures. - Abstract: In the frame of Super-Critical Reactor In Pipe Test Preparation (SCRIPT) project in China, one of the challenge tasks is to predict the transient performance of SuperCritical Water Reactor-Fuel Qualification Test (SCWR-FQT) loop under some accident conditions. Several thermal–hydraulic codes (system code, sub-channel code) are selected to perform the safety analysis. However, the system code cannot simulate the local behavior of the test bundle, and the sub-channel code is incapable of calculating the whole system behavior of the test loop. Therefore, to combine the merits of both codes, and minimizes their shortcomings, a coupled sub-channel and system code system is developed in this paper. Both of the sub-channel code COBRA-SC and system code ATHLET-SC are adapted to transient analysis of SCWR. Two codes are coupled by data transfer and data adaptation at the interface. In the new developed coupled code, the whole system behavior including safety system characteristic is analyzed by system code ATHLET-SC, whereas the local thermal–hydraulic parameters are predicted by the sub-channel code COBRA-SC. The codes are utilized to get the local thermal–hydraulic parameters in the SCWR-FQT fuel bundle under some accident case (e.g. a flow blockage during LOCA). Some measures to mitigate the accident consequence are proposed by the sensitivity study and trialed to demonstrate their effectiveness in the coupled simulation. The results indicate that the new developed code has good feasibility to transient analysis of supercritical water-cooled test. And the peak cladding temperature caused by blockage in the fuel bundle can be reduced effectively by the safety measures

The development, qualification and availability of AECL analytical, scientific and design codes

International Nuclear Information System (INIS)

Kupferschmidt, W.C.H.; Fehrenbach, P.J.; Wolgemuth, G.A.; McDonald, B.H.; Snell, V.G.

2001-01-01

Over the past several years, AECL has embarked on a comprehensive program to develop, qualify and support its key safety and licensing codes, and to make executable versions of these codes available to the international nuclear community. To this end, we have instituted a company-wide Software Quality Assurance (SQA) Program for Analytical, Scientific and Design Computer Programs to ensure that the design, development, maintenance, modification, procurement and use of computer codes within AECL is consistent with today's quality assurance standards. In addition, we have established a comprehensive Code Validation Project (CVP) with the goal of qualifying AECL's 'front-line' safety and licensing codes by 2001 December. The outcome of this initiative will be qualified codes, which are properly verified and validated for the expected range of applications, with associated statements of accuracy and uncertainty for each application. The code qualification program, based on the CSA N286.7 standard, is intended to ensure (1) that errors are not introduced into safety analyses because of deficiencies in the software, (2) that an auditable documentation base is assembled that demonstrates to the regulator that the codes are of acceptable quality, and (3) that these codes are formally qualified for their intended applications. Because AECL and the Canadian nuclear utilities (i.e., Ontario Power Generation, Bruce Power, Hydro Quebec and New Brunswick Power) generally use the same safety and licensing codes, the nuclear industry in Canada has agreed to work cooperatively together towards the development, qualification and maintenance of a common set of analysis tools, referred to as the Industry Standard Toolset (IST). This paper provides an overview of the AECL Software Quality Assurance Program and the Code Validation Project, and their associated linkages to the Canadian nuclear community's Industry Standard Toolset initiative to cooperatively qualify and support commonly

Development of the integrated system reliability analysis code MODULE

International Nuclear Information System (INIS)

Han, S.H.; Yoo, K.J.; Kim, T.W.

1987-01-01

The major components in a system reliability analysis are the determination of cut sets, importance measure, and uncertainty analysis. Various computer codes have been used for these purposes. For example, SETS and FTAP are used to determine cut sets; Importance for importance calculations; and Sample, CONINT, and MOCUP for uncertainty analysis. There have been problems when the codes run each other and the input and output are not linked, which could result in errors when preparing input for each code. The code MODULE was developed to carry out the above calculations simultaneously without linking input and outputs to other codes. MODULE can also prepare input for SETS for the case of a large fault tree that cannot be handled by MODULE. The flow diagram of the MODULE code is shown. To verify the MODULE code, two examples are selected and the results and computation times are compared with those of SETS, FTAP, CONINT, and MOCUP on both Cyber 170-875 and IBM PC/AT. Two examples are fault trees of the auxiliary feedwater system (AFWS) of Korea Nuclear Units (KNU)-1 and -2, which have 54 gates and 115 events, 39 gates and 92 events, respectively. The MODULE code has the advantage that it can calculate the cut sets, importances, and uncertainties in a single run with little increase in computing time over other codes and that it can be used in personal computers

Development and validation of a fuel performance analysis code

International Nuclear Information System (INIS)

Majalee, Aaditya V.; Chaturvedi, S.

2015-01-01

CAD has been developing a computer code 'FRAVIZ' for calculation of steady-state thermomechanical behaviour of nuclear reactor fuel rods. It contains four major modules viz., Thermal module, Fission Gas Release module, Material Properties module and Mechanical module. All these four modules are coupled to each other and feedback from each module is fed back to others to get a self-consistent evolution in time. The computer code has been checked against two FUMEX benchmarks. Modelling fuel performance in Advance Heavy Water Reactor would require additional inputs related to the fuel and some modification in the code.(author)

Object-Oriented Programming in the Development of Containment Analysis Code

International Nuclear Information System (INIS)

Han, Tae Young; Hong, Soon Joon; Hwang, Su Hyun; Lee, Byung Chul; Byun, Choong Sup

2009-01-01

After the mid 1980s, the new programming concept, Object-Oriented Programming (OOP), was introduced and designed, which has the features such as the information hiding, encapsulation, modularity and inheritance. These offered much more convenient programming paradigm to code developers. The OOP concept was readily developed into the programming language as like C++ in the 1990s and is being widely used in the modern software industry. In this paper, we show that the OOP concept is successfully applicable to the development of safety analysis code for containment and propose the more explicit and easy OOP design for developers

Multi-dimensional Code Development for Safety Analysis of LMR

International Nuclear Information System (INIS)

Ha, K. S.; Jeong, H. Y.; Kwon, Y. M.; Lee, Y. B.

2006-08-01

A liquid metal reactor loaded a metallic fuel has the inherent safety mechanism due to the several negative reactivity feedback. Although this feature demonstrated through experiments in the EBR-II, any of the computer programs until now did not exactly analyze it because of the complexity of the reactivity feedback mechanism. A multi-dimensional detail program was developed through the International Nuclear Energy Research Initiative(INERI) from 2003 to 2005. This report includes the numerical coupling the multi-dimensional program and SSC-K code which is used to the safety analysis of liquid metal reactors in KAERI. The coupled code has been proved by comparing the analysis results using the code with the results using SAS-SASSYS code of ANL for the UTOP, ULOF, and ULOHS applied to the safety analysis for KALIMER-150

Development of the CRIPTE Code for Electromagnetic Coupling

National Research Council Canada - National Science Library

Parmantier, Jean-Philippe

2005-01-01

.... This code was originally developed as part of an experiment performed under the joint US-France international data exchange program on the atmospheric electricity/aircraft interactions, DEA-AF-79-7336...

Development of the containment transient analysis code for the passive reactor

Energy Technology Data Exchange (ETDEWEB)

Hwang, Young Dong; Kim, Young In; Bae, Yoon Young; Chang, Moon Hi [Korea Atomic Energy Research Institute, Taejon (Korea)

1998-05-01

This study was performed to develop the analysis tools for the passively cooled steel containment and to construct the integrated code system which can analyze a thermal hydraulic behavior of the containment and reactor system during a loss of coolant accident. The computer code CONTEMPT4/MOD5/PCCS was developed by incorporating the passive containment cooling models to the containment pressure and temperature transient analysis computer code CONTEMPT4/MOD5. The integrated reactor thermal hydraulic analysis code system for passive reactor was constructed by coupling the best estimate thermal hydraulic system analysis code RELAP5/MOD3 and CONTEMPT4/MOD5/PCCS through the process control method. In addition, to evaluate the applicability of the code the CONTEMPT4/MOD5/PCCS was applied to the SMART(System-Integrated Modular Advanced Reactor). The pressure and temperature transient following the small break LOCA of SMART was analysed by modeling the safeguard vessel using both the newly added passive containment cooling model and existing pool model. (author). 16 refs., 22 figs., 7 tabs.

Safety analysis code SCTRAN development for SCWR and its application to CGNPC SCWR

International Nuclear Information System (INIS)

Wu, Pan; Gou, Junli; Shan, Jianqiang; Jiang, Yang; Yang, Jue; Zhang, Bo

2013-01-01

Highlights: ► A new safety analysis code named SCTRAN is developed for SCWRs. ► Capability of SCTRAN is verified by comparing with code APROS and RELAP5-3D. ► A new passive safety system is proposed for CGNPC SCWR and analyzed with SCTRAN. ► CGNPC SCWR is able to cope with two critical accidents for SCWRs, LOFA and LOCA. - Abstract: Design analysis is one of the main difficulties during the research and design of SCWRs. Currently, the development of safety analysis code for SCWR is still in its infancy all around the world, and very few computer codes could carry out the trans-critical calculations where significant changes in water properties would take place. In this paper, a safety analysis code SCTRAN for SCWRs has been developed based on code RETRAN-02, the best estimate code used for safety analysis of light water reactors. The ability of SCTRAN code to simulate transients where both supercritical and subcritical regimes are encountered has been verified by comparing with APROS and RELAP5-3D codes. Furthermore, the LOFA and LOCA transients for the CGNPC SCWR design were analyzed with SCTRAN code. The characteristics and performance of the passive safety systems applied to CGNPC SCWR were evaluated. The results show that: (1) The SCTRAN computer code developed in this study is capable to perform design analysis for SCWRs; (2) During LOFA and LOCA accidents in a CGNPC SCWR, the passive safety systems would significantly mitigate the consequences of these transients and enhance the inherent safety

BBU code development for high-power microwave generators

International Nuclear Information System (INIS)

Houck, T.L.; Westenskow, G.A.; Yu, S.S.

1992-01-01

We are developing a two-dimensional, time-dependent computer code for the simulation of transverse instabilities in support of relativistic klystron-two beam accelerator research at LLNL. The code addresses transient effects as well as both cumulative and regenerative beam breakup modes. Although designed specifically for the transport of high current (kA) beams through traveling-wave structures, it is applicable to devices consisting of multiple combinations of standing-wave, traveling-wave, and induction accelerator structures. In this paper we compare code simulations to analytical solutions for the case where there is no rf coupling between cavities, to theoretical scaling parameters for coupled cavity structures, and to experimental data involving beam breakup in the two traveling-wave output structure of our microwave generator. (Author) 4 figs., tab., 5 refs

Twelve gordian knots when developing an organizational code of ethics

NARCIS (Netherlands)

Kaptein, Muel; Wempe, Johan

1998-01-01

Following the example of the many organizations in the United States which have a code of ethics, an increasing interest on the part of companies, trade organizations, (semi-)governmental organizations and professions in the Netherlands to develop codes of ethics can be witnessed. We have been able

TRAC code development status and plans

International Nuclear Information System (INIS)

Spore, J.W.; Liles, D.R.; Nelson, R.A.

1986-01-01

This report summarizes the characteristics and current status of the TRAC-PF1/MOD1 computer code. Recent error corrections and user-convenience features are described, and several user enhancements are identified. Current plans for the release of the TRAC-PF1/MOD2 computer code and some preliminary MOD2 results are presented. This new version of the TRAC code implements stability-enhancing two-step numerics into the 3-D vessel, using partial vectorization to obtain a code that has run 400% faster than the MOD1 code

Development of a coupling code for PWR reactor cavity radiation streaming calculation

International Nuclear Information System (INIS)

Zheng, Z.; Wu, H.; Cao, L.; Zheng, Y.; Zhang, H.; Wang, M.

2012-01-01

PWR reactor cavity radiation streaming is important for the safe of the personnel and equipment, thus calculation has to be performed to evaluate the neutron flux distribution around the reactor. For this calculation, the deterministic codes have difficulties in fine geometrical modeling and need huge computer resource; and the Monte Carlo codes require very long sampling time to obtain results with acceptable precision. Therefore, a coupling method has been developed to eliminate the two problems mentioned above in each code. In this study, we develop a coupling code named DORT2MCNP to link the Sn code DORT and Monte Carlo code MCNP. DORT2MCNP is used to produce a combined surface source containing top, bottom and side surface simultaneously. Because SDEF card is unsuitable for the combined surface source, we modify the SOURCE subroutine of MCNP and compile MCNP for this application. Numerical results demonstrate the correctness of the coupling code DORT2MCNP and show reasonable agreement between the coupling method and the other two codes (DORT and MCNP). (authors)

Development of Visual CINDER Code with Visual C⧣.NET

International Nuclear Information System (INIS)

Kim, Oyeon

2016-01-01

CINDER code, CINDER' 90 or CINDER2008 that is integrated with the Monte Carlo code, MCNPX, is widely used to calculate the inventory of nuclides in irradiated materials. The MCNPX code provides decay processes to the particle transport scheme that traditionally only covered prompt processes. The integration schemes serve not only the reactor community (MCNPX burnup) but also the accelerator community as well (residual production information). The big benefit for providing these options lies in the easy cross comparison of the transmutation codes since the calculations are based on exactly the same material, neutron flux and isotope production/destruction inputs. However, it is just frustratingly cumbersome to use. In addition, multiple human interventions may increase the possibility of making errors. The number of significant digits in the input data varies in steps, which may cause big errors for highly nonlinear problems. Thus, it is worthwhile to find a new way to wrap all the codes and procedures in one consistent package which can provide ease of use. The visual CINDER code development is underway with visual C .NET framework. It provides a few benefits for the atomic transmutation simulation with CINDER code. A few interesting and useful properties of visual C .NET framework are introduced. We also showed that the wrapper could make the simulation accurate for highly nonlinear transmutation problems and also increase the possibility of direct combination a radiation transport code MCNPX with CINDER code. Direct combination of CINDER with MCNPX in a wrapper will provide more functionalities for the radiation shielding and prevention study

Development of Visual CINDER Code with Visual C⧣.NET

Energy Technology Data Exchange (ETDEWEB)

Kim, Oyeon [Institute for Modeling and Simulation Convergence, Daegu (Korea, Republic of)

2016-10-15

CINDER code, CINDER' 90 or CINDER2008 that is integrated with the Monte Carlo code, MCNPX, is widely used to calculate the inventory of nuclides in irradiated materials. The MCNPX code provides decay processes to the particle transport scheme that traditionally only covered prompt processes. The integration schemes serve not only the reactor community (MCNPX burnup) but also the accelerator community as well (residual production information). The big benefit for providing these options lies in the easy cross comparison of the transmutation codes since the calculations are based on exactly the same material, neutron flux and isotope production/destruction inputs. However, it is just frustratingly cumbersome to use. In addition, multiple human interventions may increase the possibility of making errors. The number of significant digits in the input data varies in steps, which may cause big errors for highly nonlinear problems. Thus, it is worthwhile to find a new way to wrap all the codes and procedures in one consistent package which can provide ease of use. The visual CINDER code development is underway with visual C .NET framework. It provides a few benefits for the atomic transmutation simulation with CINDER code. A few interesting and useful properties of visual C .NET framework are introduced. We also showed that the wrapper could make the simulation accurate for highly nonlinear transmutation problems and also increase the possibility of direct combination a radiation transport code MCNPX with CINDER code. Direct combination of CINDER with MCNPX in a wrapper will provide more functionalities for the radiation shielding and prevention study.

Development of general-purpose particle and heavy ion transport monte carlo code

International Nuclear Information System (INIS)

Iwase, Hiroshi; Nakamura, Takashi; Niita, Koji

2002-01-01

The high-energy particle transport code NMTC/JAM, which has been developed at JAERI, was improved for the high-energy heavy ion transport calculation by incorporating the JQMD code, the SPAR code and the Shen formula. The new NMTC/JAM named PHITS (Particle and Heavy-Ion Transport code System) is the first general-purpose heavy ion transport Monte Carlo code over the incident energies from several MeV/nucleon to several GeV/nucleon. (author)

The development of depletion program coupled with Monte Carlo computer code

International Nuclear Information System (INIS)

Nguyen Kien Cuong; Huynh Ton Nghiem; Vuong Huu Tan

2015-01-01

The paper presents the development of depletion code for light water reactor coupled with MCNP5 code called the MCDL code (Monte Carlo Depletion for Light Water Reactor). The first order differential depletion system equations of 21 actinide isotopes and 50 fission product isotopes are solved by the Radau IIA Implicit Runge Kutta (IRK) method after receiving neutron flux, reaction rates in one group energy and multiplication factors for fuel pin, fuel assembly or whole reactor core from the calculation results of the MCNP5 code. The calculation for beryllium poisoning and cooling time is also integrated in the code. To verify and validate the MCDL code, high enriched uranium (HEU) and low enriched uranium (LEU) fuel assemblies VVR-M2 types and 89 fresh HEU fuel assemblies, 92 LEU fresh fuel assemblies cores of the Dalat Nuclear Research Reactor (DNRR) have been investigated and compared with the results calculated by the SRAC code and the MCNP R EBUS linkage system code. The results show good agreement between calculated data of the MCDL code and reference codes. (author)

Development of Probabilistic Internal Dosimetry Computer Code

Energy Technology Data Exchange (ETDEWEB)

Noh, Siwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kwon, Tae-Eun [Korea Institute of Radiological and Medical Sciences, Seoul (Korea, Republic of); Lee, Jai-Ki [Korean Association for Radiation Protection, Seoul (Korea, Republic of)

2017-02-15

Internal radiation dose assessment involves biokinetic models, the corresponding parameters, measured data, and many assumptions. Every component considered in the internal dose assessment has its own uncertainty, which is propagated in the intake activity and internal dose estimates. For research or scientific purposes, and for retrospective dose reconstruction for accident scenarios occurring in workplaces having a large quantity of unsealed radionuclides, such as nuclear power plants, nuclear fuel cycle facilities, and facilities in which nuclear medicine is practiced, a quantitative uncertainty assessment of the internal dose is often required. However, no calculation tools or computer codes that incorporate all the relevant processes and their corresponding uncertainties, i.e., from the measured data to the committed dose, are available. Thus, the objective of the present study is to develop an integrated probabilistic internal-dose-assessment computer code. First, the uncertainty components in internal dosimetry are identified, and quantitative uncertainty data are collected. Then, an uncertainty database is established for each component. In order to propagate these uncertainties in an internal dose assessment, a probabilistic internal-dose-assessment system that employs the Bayesian and Monte Carlo methods. Based on the developed system, we developed a probabilistic internal-dose-assessment code by using MATLAB so as to estimate the dose distributions from the measured data with uncertainty. Using the developed code, we calculated the internal dose distribution and statistical values (e.g. the 2.5{sup th}, 5{sup th}, median, 95{sup th}, and 97.5{sup th} percentiles) for three sample scenarios. On the basis of the distributions, we performed a sensitivity analysis to determine the influence of each component on the resulting dose in order to identify the major component of the uncertainty in a bioassay. The results of this study can be applied to various

Development of Probabilistic Internal Dosimetry Computer Code

International Nuclear Information System (INIS)

Noh, Siwan; Kwon, Tae-Eun; Lee, Jai-Ki

2017-01-01

Internal radiation dose assessment involves biokinetic models, the corresponding parameters, measured data, and many assumptions. Every component considered in the internal dose assessment has its own uncertainty, which is propagated in the intake activity and internal dose estimates. For research or scientific purposes, and for retrospective dose reconstruction for accident scenarios occurring in workplaces having a large quantity of unsealed radionuclides, such as nuclear power plants, nuclear fuel cycle facilities, and facilities in which nuclear medicine is practiced, a quantitative uncertainty assessment of the internal dose is often required. However, no calculation tools or computer codes that incorporate all the relevant processes and their corresponding uncertainties, i.e., from the measured data to the committed dose, are available. Thus, the objective of the present study is to develop an integrated probabilistic internal-dose-assessment computer code. First, the uncertainty components in internal dosimetry are identified, and quantitative uncertainty data are collected. Then, an uncertainty database is established for each component. In order to propagate these uncertainties in an internal dose assessment, a probabilistic internal-dose-assessment system that employs the Bayesian and Monte Carlo methods. Based on the developed system, we developed a probabilistic internal-dose-assessment code by using MATLAB so as to estimate the dose distributions from the measured data with uncertainty. Using the developed code, we calculated the internal dose distribution and statistical values (e.g. the 2.5 th , 5 th , median, 95 th , and 97.5 th percentiles) for three sample scenarios. On the basis of the distributions, we performed a sensitivity analysis to determine the influence of each component on the resulting dose in order to identify the major component of the uncertainty in a bioassay. The results of this study can be applied to various situations. In cases

Development of 3-dimensional neutronics kinetics analysis code for CANDU-PHWR

International Nuclear Information System (INIS)

Kim, M. W.; Kim, C. H.; Hong, I. S.

2005-02-01

The followings are the major contents and scope of the research : development of kinetics power calculation module, formulation of space-dependent neutron transient analysis - implementation of 3-D and 2-G unified nodal method, verification of the kinetics module by benchmark problem - 3-D PHWR kinetics benchmark problem suggested by AECL, reactor trip simulation by shutdown system 1 in Wolsong unit 2. Development of a dynamic linked library code, SCAN D LL, for the coupled calculation with RELAP-CANDU : modeling of shutdown system 1, development of automatic shutdown module - automatic trip module based on rate log power control logic, automatic insertion of shutdown system 1. Development of a link code for coupled calculation - development of SCAN D LL(windows version), verification of coupled code by - 40% reactor inlet header break LOCA power pulse, 100% reactor outlet header break LOCA power pulse, 50% pump suction break LOCA power pulse

Development Perspective of Regulatory Audit Code System for SFR Nuclear Safety Evaluation

Energy Technology Data Exchange (ETDEWEB)

Bae, Moo Hoon; Lee, Gil Soo; Shin, An Dong; Suh, Nam Duk [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2012-05-15

A sodium-cooled fast reactor (SFR) in Korea is based on the KALIMER-600 concept developed by KAERI. Based on 'Long-term R and D Plan for Future Reactor Systems' which was approved by the Korea Atomic Energy Commission in 2008, the KAERI designer is scheduled to apply the design certification of the prototype SFR in 2017. In order to establish regulatory infrastructure for the licensing of a prototype SFR, KINS has develop the regulatory requirements for the demonstration SFR since 2010, and are scheduled to develop the regulatory audit code systems in regard to core, fuel, and system, etc. since 2012. In this study, the domestic code systems used for core design and safety evaluation of PWRs and the nuclear physics and code system for SFRs were briefly reviewed, and the development perspective of regulatory audit code system for SFR nuclear safety evaluation were derived

Software Certification - Coding, Code, and Coders

Science.gov (United States)

Havelund, Klaus; Holzmann, Gerard J.

2011-01-01

We describe a certification approach for software development that has been adopted at our organization. JPL develops robotic spacecraft for the exploration of the solar system. The flight software that controls these spacecraft is considered to be mission critical. We argue that the goal of a software certification process cannot be the development of "perfect" software, i.e., software that can be formally proven to be correct under all imaginable and unimaginable circumstances. More realistically, the goal is to guarantee a software development process that is conducted by knowledgeable engineers, who follow generally accepted procedures to control known risks, while meeting agreed upon standards of workmanship. We target three specific issues that must be addressed in such a certification procedure: the coding process, the code that is developed, and the skills of the coders. The coding process is driven by standards (e.g., a coding standard) and tools. The code is mechanically checked against the standard with the help of state-of-the-art static source code analyzers. The coders, finally, are certified in on-site training courses that include formal exams.

Development of burnup methods and capabilities in Monte Carlo code RMC

International Nuclear Information System (INIS)

She, Ding; Liu, Yuxuan; Wang, Kan; Yu, Ganglin; Forget, Benoit; Romano, Paul K.; Smith, Kord

2013-01-01

Highlights: ► The RMC code has been developed aiming at large-scale burnup calculations. ► Matrix exponential methods are employed to solve the depletion equations. ► The Energy-Bin method reduces the time expense of treating ACE libraries. ► The Cell-Mapping method is efficient to handle massive amounts of tally cells. ► Parallelized depletion is necessary for massive amounts of burnup regions. -- Abstract: The Monte Carlo burnup calculation has always been a challenging problem because of its large time consumption when applied to full-scale assembly or core calculations, and thus its application in routine analysis is limited. Most existing MC burnup codes are usually external wrappers between a MC code, e.g. MCNP, and a depletion code, e.g. ORIGEN. The code RMC is a newly developed MC code with an embedded depletion module aimed at performing burnup calculations of large-scale problems with high efficiency. Several measures have been taken to strengthen the burnup capabilities of RMC. Firstly, an accurate and efficient depletion module called DEPTH has been developed and built in, which employs the rational approximation and polynomial approximation methods. Secondly, the Energy-Bin method and the Cell-Mapping method are implemented to speed up the transport calculations with large numbers of nuclides and tally cells. Thirdly, the batch tally method and the parallelized depletion module have been utilized to better handle cases with massive amounts of burnup regions in parallel calculations. Burnup cases including a PWR pin and a 5 × 5 assembly group are calculated, thereby demonstrating the burnup capabilities of the RMC code. In addition, the computational time and memory requirements of RMC are compared with other MC burnup codes.

Analyses to support development of risk-informed separation distances for hydrogen codes and standards.

Energy Technology Data Exchange (ETDEWEB)

LaChance, Jeffrey L.; Houf, William G. (Sandia National Laboratories, Livermore, CA); Fluer, Inc., Paso Robels, CA; Fluer, Larry (Fluer, Inc., Paso Robels, CA); Middleton, Bobby

2009-03-01

The development of a set of safety codes and standards for hydrogen facilities is necessary to ensure they are designed and operated safely. To help ensure that a hydrogen facility meets an acceptable level of risk, code and standard development organizations are tilizing risk-informed concepts in developing hydrogen codes and standards.

Application of software quality assurance to a specific scientific code development task

International Nuclear Information System (INIS)

Dronkers, J.J.

1986-03-01

This paper describes an application of software quality assurance to a specific scientific code development program. The software quality assurance program consists of three major components: administrative control, configuration management, and user documentation. The program attempts to be consistent with existing local traditions of scientific code development while at the same time providing a controlled process of development

Development of 3-D Flow Analysis Code for Fuel Assembly using Unstructured Grid System

Energy Technology Data Exchange (ETDEWEB)

Myong, Hyon Kook; Kim, Jong Eun; Ahn, Jong Ki; Yang, Seung Yong [Kookmin Univ., Seoul (Korea, Republic of)

2007-03-15

The flow through a nuclear rod bundle with mixing vanes are very complex and required a suitable turbulence model to be predicted accurately. Final objective of this study is to develop a CFD code for fluid flow and heat transfer analysis in a nuclear fuel assembly using unstructured grid system. In order to develop a CFD code for fluid flow and heat transfer analysis in a nuclear fuel assembly using unstructured grid system, the following researches are made: - Development of numerical algorithm for CFD code's solver - Grid and geometric connectivity data - Development of software(PowerCFD code) for fluid flow and heat transfer analysis in a nuclear fuel assembly using unstructured grid system - Modulation of software(PowerCFD code) - Development of turbulence model - Development of analysis module of RANS/LES hybrid models - Analysis of turbulent flow and heat transfer - Basic study on LES analysis - Development of main frame on pre/post processors based on GUI - Algorithm for fully-developed flow.

Development of 3-D Flow Analysis Code for Fuel Assembly using Unstructured Grid System

International Nuclear Information System (INIS)

Myong, Hyon Kook; Kim, Jong Eun; Ahn, Jong Ki; Yang, Seung Yong

2007-03-01

The flow through a nuclear rod bundle with mixing vanes are very complex and required a suitable turbulence model to be predicted accurately. Final objective of this study is to develop a CFD code for fluid flow and heat transfer analysis in a nuclear fuel assembly using unstructured grid system. In order to develop a CFD code for fluid flow and heat transfer analysis in a nuclear fuel assembly using unstructured grid system, the following researches are made: - Development of numerical algorithm for CFD code's solver - Grid and geometric connectivity data - Development of software(PowerCFD code) for fluid flow and heat transfer analysis in a nuclear fuel assembly using unstructured grid system - Modulation of software(PowerCFD code) - Development of turbulence model - Development of analysis module of RANS/LES hybrid models - Analysis of turbulent flow and heat transfer - Basic study on LES analysis - Development of main frame on pre/post processors based on GUI - Algorithm for fully-developed flow

Development and application of a system analysis code for liquid fueled molten salt reactors based on RELAP5 code

Energy Technology Data Exchange (ETDEWEB)

Shi, Chengbin [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Cheng, Maosong, E-mail: mscheng@sinap.ac.cn [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Liu, Guimin [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China)

2016-08-15

Highlights: • New point kinetics and thermo-hydraulics models as well as a numerical method are added into RELAP5 code to be suitable for liquid fueled molten salt reactor. • The extended REALP5 code is verified by the experimental benchmarks of MSRE. • The different transient scenarios of the MSBR are simulated to evaluate performance during the transients. - Abstract: The molten salt reactor (MSR) is one of the six advanced reactor concepts declared by the Generation IV International Forum (GIF), which can be characterized by attractive attributes as inherent safety, economical efficiency, natural resource protection, sustainable development and nuclear non-proliferation. It is important to make system safety analysis for nuclear power plant of MSR. In this paper, in order to developing a system analysis code suitable for liquid fueled molten salt reactors, the point kinetics and thermo-hydraulic models as well as the numerical method in thermal–hydraulic transient code Reactor Excursion and Leak Analysis Program (RELAP5) developed at the Idaho National Engineering Laboratory (INEL) for the U.S. Nuclear Regulatory Commission (NRC) are extended and verified by Molten Salt Reactor Experiment (MSRE) experimental benchmarks. And then, four transient scenarios including the load demand change, the primary flow transient, the secondary flow transient and the reactivity transient of the Molten Salt Breeder Reactor (MSBR) are modeled and simulated so as to evaluate the performance of the reactor during the anticipated transient events using the extended RELAP5 code. The results indicate the extended RELAP5 code is effective and well suited to the liquid fueled molten salt reactor, and the MSBR has strong inherent safety characteristics because of its large negative reactivity coefficient. In the future, the extended RELAP5 code will be used to perform transient safety analysis for a liquid fueled thorium molten salt reactor named TMSR-LF developed by the Center

Development and application of a system analysis code for liquid fueled molten salt reactors based on RELAP5 code

International Nuclear Information System (INIS)

Shi, Chengbin; Cheng, Maosong; Liu, Guimin

2016-01-01

Highlights: • New point kinetics and thermo-hydraulics models as well as a numerical method are added into RELAP5 code to be suitable for liquid fueled molten salt reactor. • The extended REALP5 code is verified by the experimental benchmarks of MSRE. • The different transient scenarios of the MSBR are simulated to evaluate performance during the transients. - Abstract: The molten salt reactor (MSR) is one of the six advanced reactor concepts declared by the Generation IV International Forum (GIF), which can be characterized by attractive attributes as inherent safety, economical efficiency, natural resource protection, sustainable development and nuclear non-proliferation. It is important to make system safety analysis for nuclear power plant of MSR. In this paper, in order to developing a system analysis code suitable for liquid fueled molten salt reactors, the point kinetics and thermo-hydraulic models as well as the numerical method in thermal–hydraulic transient code Reactor Excursion and Leak Analysis Program (RELAP5) developed at the Idaho National Engineering Laboratory (INEL) for the U.S. Nuclear Regulatory Commission (NRC) are extended and verified by Molten Salt Reactor Experiment (MSRE) experimental benchmarks. And then, four transient scenarios including the load demand change, the primary flow transient, the secondary flow transient and the reactivity transient of the Molten Salt Breeder Reactor (MSBR) are modeled and simulated so as to evaluate the performance of the reactor during the anticipated transient events using the extended RELAP5 code. The results indicate the extended RELAP5 code is effective and well suited to the liquid fueled molten salt reactor, and the MSBR has strong inherent safety characteristics because of its large negative reactivity coefficient. In the future, the extended RELAP5 code will be used to perform transient safety analysis for a liquid fueled thorium molten salt reactor named TMSR-LF developed by the Center

Development Of A Navier-Stokes Computer Code

Science.gov (United States)

Yoon, Seokkwan; Kwak, Dochan

1993-01-01

Report discusses aspects of development of CENS3D computer code, solving three-dimensional Navier-Stokes equations of compressible, viscous, unsteady flow. Implements implicit finite-difference or finite-volume numerical-integration scheme, called "lower-upper symmetric-Gauss-Seidel" (LU-SGS), offering potential for very low computer time per iteration and for fast convergence.

Development of An Automatic Verification Program for Thermal-hydraulic System Codes

Energy Technology Data Exchange (ETDEWEB)

Lee, J. Y.; Ahn, K. T.; Ko, S. H.; Kim, Y. S.; Kim, D. W. [Pusan National University, Busan (Korea, Republic of); Suh, J. S.; Cho, Y. S.; Jeong, J. J. [System Engineering and Technology Co., Daejeon (Korea, Republic of)

2012-05-15

As a project activity of the capstone design competitive exhibition, supported by the Education Center for Green Industry-friendly Fusion Technology (GIFT), we have developed a computer program which can automatically perform non-regression test, which is needed repeatedly during a developmental process of a thermal-hydraulic system code, such as the SPACE code. A non-regression test (NRT) is an approach to software testing. The purpose of the non-regression testing is to verify whether, after updating a given software application (in this case, the code), previous software functions have not been compromised. The goal is to prevent software regression, whereby adding new features results in software bugs. As the NRT is performed repeatedly, a lot of time and human resources will be needed during the development period of a code. It may cause development period delay. To reduce the cost and the human resources and to prevent wasting time, non-regression tests need to be automatized. As a tool to develop an automatic verification program, we have used Visual Basic for Application (VBA). VBA is an implementation of Microsoft's event-driven programming language Visual Basic 6 and its associated integrated development environment, which are built into most Microsoft Office applications (In this case, Excel)

Development of An Automatic Verification Program for Thermal-hydraulic System Codes

International Nuclear Information System (INIS)

Lee, J. Y.; Ahn, K. T.; Ko, S. H.; Kim, Y. S.; Kim, D. W.; Suh, J. S.; Cho, Y. S.; Jeong, J. J.

2012-01-01

As a project activity of the capstone design competitive exhibition, supported by the Education Center for Green Industry-friendly Fusion Technology (GIFT), we have developed a computer program which can automatically perform non-regression test, which is needed repeatedly during a developmental process of a thermal-hydraulic system code, such as the SPACE code. A non-regression test (NRT) is an approach to software testing. The purpose of the non-regression testing is to verify whether, after updating a given software application (in this case, the code), previous software functions have not been compromised. The goal is to prevent software regression, whereby adding new features results in software bugs. As the NRT is performed repeatedly, a lot of time and human resources will be needed during the development period of a code. It may cause development period delay. To reduce the cost and the human resources and to prevent wasting time, non-regression tests need to be automatized. As a tool to develop an automatic verification program, we have used Visual Basic for Application (VBA). VBA is an implementation of Microsoft's event-driven programming language Visual Basic 6 and its associated integrated development environment, which are built into most Microsoft Office applications (In this case, Excel)

Application of software engineering to development of reactor safety codes

International Nuclear Information System (INIS)

Wilburn, N.P.; Niccoli, L.G.

1981-01-01

Software Engineering, which is a systematic methodology by which a large scale software development project is partitioned into manageable pieces, has been applied to the development of LMFBR safety codes. The techniques have been applied extensively in the business and aerospace communities and have provided an answer to the drastically increasing cost of developing and maintaining software. The five phases of software engineering (Survey, Analysis, Design, Implementation, and Testing) were applied in turn to development of these codes, along with Walkthroughs (peer review) at each stage. The application of these techniques has resulted in SUPERIOR SOFTWARE which is well documented, thoroughly tested, easy to modify, easier to use and maintain. The development projects have resulted in lower overall cost. (orig.) [de

Development of the criticality accident analysis code, AGNES

International Nuclear Information System (INIS)

Nakajima, Ken

1989-01-01

In the design works for the facilities which handle nuclear fuel, the evaluation of criticality accidents cannot be avoided even if their possibility is as small as negligible. In particular in the system using solution fuel like uranyl nitrate, solution has the property easily becoming dangerous form, and all the past criticality accidents occurred in the case of solution, therefore, the evaluation of criticality accidents becomes the most important item of safety analysis. When a criticality accident occurred in a solution fuel system, due to the generation and movement of radiolysis gas voids, the oscillation of power output and pressure pulses are observed. In order to evaluate the effect of criticality accidents, these output oscillation and pressure pulses must be calculated accurately. For this purpose, the development of the dynamic characteristic code AGNES (Accidentally Generated Nuclear Excursion Simulation code) was carried out. The AGNES is the reactor dynamic characteristic code having two independent void models. Modified energy model and pressure model, and as the benchmark calculation of the AGNES code, the results of the experimental analysis on the CRAC experiment are reported. (K.I.)

Development of an integral computer code for simulation of heat exchangers

International Nuclear Information System (INIS)

Horvat, A.; Catton, I.

2001-01-01

Heat exchangers are one of the basic installations in power and process industries. The present guidelines provide an ad-hoc solution to certain design problems. A unified approach based on simultaneous modeling of thermal-hydraulics and structural behavior does not exist. The present paper describes the development of integral numerical code for simulation of heat exchangers. The code is based on Volume Averaging Technique (VAT) for porous media flow modeling. The calculated values of the whole-section drag and heat transfer coefficients show an excellent agreement with already published values. The matching results prove the correctness of the selected approach and verify the developed numerical code used for this calculation.(author)

Development of Advanced Suite of Deterministic Codes for VHTR Physics Analysis

Energy Technology Data Exchange (ETDEWEB)

Kim, Kang Seog; Cho, J. Y.; Lee, K. H. (and others)

2007-07-15

Advanced Suites of deterministic codes for VHTR physics analysis has been developed for detailed analysis of current and advanced reactor designs as part of a US-ROK collaborative I-NERI project. These code suites include the conventional 2-step procedure in which a few group constants are generated by a transport lattice calculation, and the reactor physics analysis is performed by a 3-dimensional diffusion calculation, and a whole core transport code that can model local heterogeneities directly at the core level. Particular modeling issues in physics analysis of the gas-cooled VHTRs were resolved, which include a double heterogeneity of the coated fuel particles, a neutron streaming in the coolant channels, a strong core-reflector interaction, and large spectrum shifts due to changes of the surrounding environment, temperature and burnup. And the geometry handling capability of the DeCART code were extended to deal with the hexagonal fuel elements of the VHTR core. The developed code suites were validated and verified by comparing the computational results with those of the Monte Carlo calculations for the benchmark problems.

Software requirements specification document for the AREST code development

International Nuclear Information System (INIS)

Engel, D.W.; McGrail, B.P.; Whitney, P.D.; Gray, W.J.; Williford, R.E.; White, M.D.; Eslinger, P.W.; Altenhofen, M.K.

1993-11-01

The Analysis of the Repository Source Term (AREST) computer code was selected in 1992 by the U.S. Department of Energy. The AREST code will be used to analyze the performance of an underground high level nuclear waste repository. The AREST code is being modified by the Pacific Northwest Laboratory (PNL) in order to evaluate the engineered barrier and waste package designs, model regulatory compliance, analyze sensitivities, and support total systems performance assessment modeling. The current version of the AREST code was developed to be a very useful tool for analyzing model uncertainties and sensitivities to input parameters. The code has also been used successfully in supplying source-terms that were used in a total systems performance assessment. The current version, however, has been found to be inadequate for the comparison and selection of a design for the waste package. This is due to the assumptions and simplifications made in the selection of the process and system models. Thus, the new version of the AREST code will be designed to focus on the details of the individual processes and implementation of more realistic models. This document describes the requirements of the new models that will be implemented. Included in this document is a section describing the near-field environmental conditions for this waste package modeling, description of the new process models that will be implemented, and a description of the computer requirements for the new version of the AREST code

Seismic Analysis Code (SAC): Development, porting, and maintenance within a legacy code base

Science.gov (United States)

Savage, B.; Snoke, J. A.

2017-12-01

The Seismic Analysis Code (SAC) is the result of toil of many developers over almost a 40-year history. Initially a Fortran-based code, it has undergone major transitions in underlying bit size from 16 to 32, in the 1980s, and 32 to 64 in 2009; as well as a change in language from Fortran to C in the late 1990s. Maintenance of SAC, the program and its associated libraries, have tracked changes in hardware and operating systems including the advent of Linux in the early 1990, the emergence and demise of Sun/Solaris, variants of OSX processors (PowerPC and x86), and Windows (Cygwin). Traces of these systems are still visible in source code and associated comments. A major concern while improving and maintaining a routinely used, legacy code is a fear of introducing bugs or inadvertently removing favorite features of long-time users. Prior to 2004, SAC was maintained and distributed by LLNL (Lawrence Livermore National Lab). In that year, the license was transferred from LLNL to IRIS (Incorporated Research Institutions for Seismology), but the license is not open source. However, there have been thousands of downloads a year of the package, either source code or binaries for specific system. Starting in 2004, the co-authors have maintained the SAC package for IRIS. In our updates, we fixed bugs, incorporated newly introduced seismic analysis procedures (such as EVALRESP), added new, accessible features (plotting and parsing), and improved the documentation (now in HTML and PDF formats). Moreover, we have added modern software engineering practices to the development of SAC including use of recent source control systems, high-level tests, and scripted, virtualized environments for rapid testing and building. Finally, a "sac-help" listserv (administered by IRIS) was setup for SAC-related issues and is the primary avenue for users seeking advice and reporting bugs. Attempts are always made to respond to issues and bugs in a timely fashion. For the past thirty-plus years

Development of a detailed core flow analysis code for prismatic fuel reactors

International Nuclear Information System (INIS)

Bennett, R.G.

1990-01-01

The detailed analysis of the core flow distribution in prismatic fuel reactors is of interest for modular high-temperature gas-cooled reactor (MHTGR) design and safety analyses. Such analyses involve the steady-state flow of helium through highly cross-connected flow paths in and around the prismatic fuel elements. Several computer codes have been developed for this purpose. However, since they are proprietary codes, they are not generally available for independent MHTGR design confirmation. The previously developed codes do not consider the exchange or diversion of flow between individual bypass gaps with much detail. Such a capability could be important in the analysis of potential fuel block motion, such as occurred in the Fort St. Vrain reactor, or for the analysis of the conditions around a flow blockage or misloaded fuel block. This work develops a computer code with fairly general-purpose capabilities for modeling the flow in regions of prismatic fuel cores. The code, called BYPASS solves a finite difference control volume formulation of the compressible, steady-state fluid flow in highly cross-connected flow paths typical of the MHTGR

The development of a transient neutron flux solution in the PANTHER code

International Nuclear Information System (INIS)

Hutt, P.K.; Knight, M.P.

1990-01-01

In the United Kingdom a new three-dimensional, two-group, homogeneous reactor diffusion code, PANTHER, has been developed for the analysis of pressurized water reactors (PWRs) and advanced gas-cooled reactors (AGRs). The code can perform a comprehensive range of calculations, steady state, depletion, and transient with either a finite difference or analytic nodal flux solution. The nodal solution allows the representation of within-node burnup variation and pin-power reconstruction in either steady-state or transient mode. Specific steady-state and transient thermal feedback modules are included for both PWRs and AGRs. The code is being developed to perform a complete range of reactor calculations from online operational support to fuel management and fault transient analysis. In the area of transient analysis, the code is currently being used for a number of PWR fault transient assessments, including rod ejection and steam-line break. In addition, work is proceeding to incorporate the PANTHER 3D nodal transient solution in the TRAC-P code. This paper outlines the development of the transient flux solutions within PANTHER

Methodology, status, and plans for development and assessment of the RELAP5 code

Energy Technology Data Exchange (ETDEWEB)

Johnson, G.W.; Riemke, R.A. [Idaho National Engineering Laboratory, Idaho Falls, ID (United States)

1997-07-01

RELAP/MOD3 is a computer code used for the simulation of transients and accidents in light-water nuclear power plants. The objective of the program to develop and maintain RELAP5 was and is to provide the U.S. Nuclear Regulatory Commission with an independent tool for assessing reactor safety. This paper describes code requirements, models, solution scheme, language and structure, user interface validation, and documentation. The paper also describes the current and near term development program and provides an assessment of the code`s strengths and limitations.

Methodology, status and plans for development and assessment of TUF and CATHENA codes

Energy Technology Data Exchange (ETDEWEB)

Luxat, J.C.; Liu, W.S.; Leung, R.K. [Ontario Hydro, Toronto (Canada)] [and others

1997-07-01

An overview is presented of the Canadian two-fluid computer codes TUF and CATHENA with specific focus on the constraints imposed during development of these codes and the areas of application for which they are intended. Additionally a process for systematic assessment of these codes is described which is part of a broader, industry based initiative for validation of computer codes used in all major disciplines of safety analysis. This is intended to provide both the licensee and the regulator in Canada with an objective basis for assessing the adequacy of codes for use in specific applications. Although focused specifically on CANDU reactors, Canadian experience in developing advanced two-fluid codes to meet wide-ranging application needs while maintaining past investment in plant modelling provides a useful contribution to international efforts in this area.

Methodology, status and plans for development and assessment of TUF and CATHENA codes

International Nuclear Information System (INIS)

Luxat, J.C.; Liu, W.S.; Leung, R.K.

1997-01-01

An overview is presented of the Canadian two-fluid computer codes TUF and CATHENA with specific focus on the constraints imposed during development of these codes and the areas of application for which they are intended. Additionally a process for systematic assessment of these codes is described which is part of a broader, industry based initiative for validation of computer codes used in all major disciplines of safety analysis. This is intended to provide both the licensee and the regulator in Canada with an objective basis for assessing the adequacy of codes for use in specific applications. Although focused specifically on CANDU reactors, Canadian experience in developing advanced two-fluid codes to meet wide-ranging application needs while maintaining past investment in plant modelling provides a useful contribution to international efforts in this area

Development and validation of ALEPH Monte Carlo burn-up code

International Nuclear Information System (INIS)

Stankovskiy, A.; Van den Eynde, G.; Vidmar, T.

2011-01-01

The Monte-Carlo burn-up code ALEPH is being developed in SCK-CEN since 2004. Belonging to the category of shells coupling Monte Carlo transport (MCNP or MCNPX) and 'deterministic' depletion codes (ORIGEN-2.2), ALEPH possess some unique features that distinguish it from other codes. The most important feature is full data consistency between steady-state Monte Carlo and time-dependent depletion calculations. Recent improvements of ALEPH concern full implementation of general-purpose nuclear data libraries (JEFF-3.1.1, ENDF/B-VII, JENDL-3.3). The upgraded version of the code is capable to treat isomeric branching ratios, neutron induced fission product yields, spontaneous fission yields and energy release per fission recorded in ENDF-formatted data files. The alternative algorithm for time evolution of nuclide concentrations is added. A predictor-corrector mechanism and the calculation of nuclear heating are available as well. The validation of the code on REBUS experimental programme results has been performed. The upgraded version of ALEPH has shown better agreement with measured data than other codes, including previous version of ALEPH. (authors)

Development of three dimensional transient analysis code STTA for SCWR core

International Nuclear Information System (INIS)

Wang, Lianjie; Zhao, Wenbo; Chen, Bingde; Yao, Dong; Yang, Ping

2015-01-01

Highlights: • A coupled three dimensional neutronics/thermal-hydraulics code STTA is developed for SCWR core transient analysis. • The Dynamic Link Libraries method is adopted for coupling computation for SCWR multi-flow core transient analysis. • The NEACRP-L-335 PWR benchmark problems are studied to verify STTA. • The SCWR rod ejection problems are studied to verify STTA. • STTA meets what is expected from a code for SCWR core 3-D transient preliminary analysis. - Abstract: A coupled three dimensional neutronics/thermal-hydraulics code STTA (SCWR Three dimensional Transient Analysis code) is developed for SCWR core transient analysis. Nodal Green’s Function Method based on the second boundary condition (NGFMN-K) is used for solving transient neutron diffusion equation. The SCWR sub-channel code ATHAS is integrated into NGFMN-K through the serial integration coupling approach. The NEACRP-L-335 PWR benchmark problem and SCWR rod ejection problems are studied to verify STTA. Numerical results show that the PWR solution of STTA agrees well with reference solutions and the SCWR solution is reasonable. The coupled code can be well applied to the core transients and accidents analysis with 3-D core model during both subcritical pressure and supercritical pressure operation

Development of the three dimensional flow model in the SPACE code

International Nuclear Information System (INIS)

Oh, Myung Taek; Park, Chan Eok; Kim, Shin Whan

2014-01-01

SPACE (Safety and Performance Analysis CodE) is a nuclear plant safety analysis code, which has been developed in the Republic of Korea through a joint research between the Korean nuclear industry and research institutes. The SPACE code has been developed with multi-dimensional capabilities as a requirement of the next generation safety code. It allows users to more accurately model the multi-dimensional flow behavior that can be exhibited in components such as the core, lower plenum, upper plenum and downcomer region. Based on generalized models, the code can model any configuration or type of fluid system. All the geometric quantities of mesh are described in terms of cell volume, centroid, face area, and face center, so that it can naturally represent not only the one dimensional (1D) or three dimensional (3D) Cartesian system, but also the cylindrical mesh system. It is possible to simulate large and complex domains by modelling the complex parts with a 3D approach and the rest of the system with a 1D approach. By 1D/3D co-simulation, more realistic conditions and component models can be obtained, providing a deeper understanding of complex systems, and it is expected to overcome the shortcomings of 1D system codes. (author)

Health effects estimation code development for accident consequence analysis

International Nuclear Information System (INIS)

Togawa, O.; Homma, T.

1992-01-01

As part of a computer code system for nuclear reactor accident consequence analysis, two computer codes have been developed for estimating health effects expected to occur following an accident. Health effects models used in the codes are based on the models of NUREG/CR-4214 and are revised for the Japanese population on the basis of the data from the reassessment of the radiation dosimetry and information derived from epidemiological studies on atomic bomb survivors of Hiroshima and Nagasaki. The health effects models include early and continuing effects, late somatic effects and genetic effects. The values of some model parameters are revised for early mortality. The models are modified for predicting late somatic effects such as leukemia and various kinds of cancers. The models for genetic effects are the same as those of NUREG. In order to test the performance of one of these codes, it is applied to the U.S. and Japanese populations. This paper provides descriptions of health effects models used in the two codes and gives comparisons of the mortality risks from each type of cancer for the two populations. (author)

Recent development and application of a new safety analysis code for fusion reactors

Energy Technology Data Exchange (ETDEWEB)

Merrill, Brad J., E-mail: Brad.Merrill@inl.gov; Humrickhouse, Paul W.; Shimada, Masashi

2016-11-01

Highlights: • This paper presents recent code development activities for the MELCOR for fusion and Tritium Migration Analysis Program computer codes at the Idaho National Engineering Laboratory. • The capabilities of these computer codes are being merged into a single safety analysis tool for fusion reactor accidents. • The result of benchmarking these codes against previous code versions is presented by the authors of this paper. • This new capability is applied to study the tritium inventory and permeation rate for a water cold tungsten divertor that has neutron damage at 0.3 dpa. - Abstract: This paper describes the recent progress made in the development of two codes for fusion reactor safety assessments at the Idaho National Laboratory (INL): MELCOR for fusion and the Tritium Migration Analysis Program (TMAP). During the ITER engineering design activity (EDA), the INL Fusion Safety Program (FSP) modified the MELCOR 1.8.2 code for fusion applications to perform ITER thermal hydraulic safety analyses. Because MELCOR has undergone many improvements at SNL-NM since version 1.8.2 was released, the INL FSP recently imported these same fusion modifications into the MELCOR 1.8.6 code, along with the multiple fluids modifications of MELCOR 1.8.5 for fusion used in US advanced fusion reactor design studies. TMAP has also been under development for several decades at the INL by the FSP. TMAP treats multi-specie surface absorption and diffusion in composite materials with dislocation traps, plus the movement of these species from room to room by fluid flow within a given facility. Recently, TMAP was updated to consider multiple trap site types to allow the simulation of experimental data from neutron irradiated tungsten. The natural development path for both of these codes is to merge their capabilities into one computer code to provide a more comprehensive safety tool for analyzing accidents in fusion reactors. In this paper we detail recent developments in this

Recent development and application of a new safety analysis code for fusion reactors

International Nuclear Information System (INIS)

Merrill, Brad J.; Humrickhouse, Paul W.; Shimada, Masashi

2016-01-01

Highlights: • This paper presents recent code development activities for the MELCOR for fusion and Tritium Migration Analysis Program computer codes at the Idaho National Engineering Laboratory. • The capabilities of these computer codes are being merged into a single safety analysis tool for fusion reactor accidents. • The result of benchmarking these codes against previous code versions is presented by the authors of this paper. • This new capability is applied to study the tritium inventory and permeation rate for a water cold tungsten divertor that has neutron damage at 0.3 dpa. - Abstract: This paper describes the recent progress made in the development of two codes for fusion reactor safety assessments at the Idaho National Laboratory (INL): MELCOR for fusion and the Tritium Migration Analysis Program (TMAP). During the ITER engineering design activity (EDA), the INL Fusion Safety Program (FSP) modified the MELCOR 1.8.2 code for fusion applications to perform ITER thermal hydraulic safety analyses. Because MELCOR has undergone many improvements at SNL-NM since version 1.8.2 was released, the INL FSP recently imported these same fusion modifications into the MELCOR 1.8.6 code, along with the multiple fluids modifications of MELCOR 1.8.5 for fusion used in US advanced fusion reactor design studies. TMAP has also been under development for several decades at the INL by the FSP. TMAP treats multi-specie surface absorption and diffusion in composite materials with dislocation traps, plus the movement of these species from room to room by fluid flow within a given facility. Recently, TMAP was updated to consider multiple trap site types to allow the simulation of experimental data from neutron irradiated tungsten. The natural development path for both of these codes is to merge their capabilities into one computer code to provide a more comprehensive safety tool for analyzing accidents in fusion reactors. In this paper we detail recent developments in this

A framework for developing finite element codes for multi-disciplinary applications.

OpenAIRE

Dadvand, Pooyan

2007-01-01

The world of computing simulation has experienced great progresses in recent years and requires more exigent multidisciplinary challenges to satisfy the new upcoming demands. Increasing the importance of solving multi-disciplinary problems makes developers put more attention to these problems and deal with difficulties involved in developing software in this area. Conventional finite element codes have several difficulties in dealing with multi-disciplinary problems. Many of these codes are d...

Development of a general coupling interface for the fuel performance code transuranus tested with the reactor dynamic code DYN3D

International Nuclear Information System (INIS)

Holt, L.; Rohde, U.; Seidl, M.; Schubert, A.; Van Uffelen, P.

2013-01-01

Several institutions plan to couple the fuel performance code TRANSURANUS developed by the European Institute for Transuranium Elements with their own codes. One of these codes is the reactor dynamic code DYN3D maintained by the Helmholtz-Zentrum Dresden - Rossendorf. DYN3D was developed originally for VVER type reactors and was extended later to western type reactors. Usually, the fuel rod behavior is modeled in thermal hydraulics and neutronic codes in a simplified manner. The main idea of this coupling is to describe the fuel rod behavior in the frame of core safety analysis in a more detailed way, e.g. including the influence of the high burn-up structure, geometry changes and fission gas release. It allows to take benefit from the improved computational power and software achieved over the last two decades. The coupling interface was developed in a general way from the beginning. Thence it can be easily used also by other codes for a coupling with TRANSURANUS. The user can choose between a one-way as well as a two-way online coupling option. For a one-way online coupling, DYN3D provides only the time-dependent rod power and thermal hydraulics conditions to TRANSURANUS, but the fuel performance code doesn’t transfer any variable back to DYN3D. In a two-way online coupling, TRANSURANUS in addition transfers parameters like fuel temperature and cladding temperature back to DYN3D. This list of variables can be extended easily by geometric and further variables of interest. First results of the code system DYN3D-TRANSURANUS will be presented for a control rod ejection transient in a modern western type reactor. Pre-analyses show already that a detailed fuel rod behavior modeling will influence the thermal hydraulics and thence also the neutronics due to the Doppler reactivity effect of the fuel temperature. The coupled code system has therefore a potential to improve the assessment of safety criteria. The developed code system DYN3D-TRANSURANUS can be used also

Development of essential system technologies for advanced reactor - Development of natural circulation analysis code for integral reactor

Energy Technology Data Exchange (ETDEWEB)

Park, Goon Cherl; Park, Ik Gyu; Kim, Jae Hak; Lee, Sang Min; Kim, Tae Wan [Seoul National University, Seoul (Korea)

1999-04-01

The objective of this study is to understand the natural circulation characteristics of integral type reactors and to develope the natural circulation analysis code for integral type reactors. This study is focused on the asymmetric 3-dimensional flow during natural circulation such as 1/4 steam generator section isolation and the inclination of the reactor systems. Natural circulation experiments were done using small-scale facilities of integral reactor SMART (System-Integrated Modular Advanced ReacTor). CFX4 code was used to investigate the flow patterns and thermal mixing phenomena in upper pressure header and downcomer. Differences between normal operation of all steam generators and the 1/4 section isolation conditions were observed and the results were used as the data 1/4 section isolation conditions were observed and the results were used as the data for RETRAN-03/INT code validation. RETRAN-03 code was modified for the development of natural circulation analysis code for integral type reactors, which was development of natural circulation analysis code for integral type reactors, which was named as RETRAN-03/INT. 3-dimensional analysis models for asymmetric flow in integral type reactors were developed using vector momentum equations in RETRAN-03. Analysis results using RETRAN-03/INT were compared with experimental and CFX4 analysis results and showed good agreements. The natural circulation characteristics obtained in this study will provide the important and fundamental design features for the future small and medium integral reactors. (author). 29 refs., 75 figs., 18 tabs.

Development of EASYQAD version β: A Visualization Code System for QAD-CGGP-A Gamma and Neutron Shielding Calculation Code

International Nuclear Information System (INIS)

Kim, Jae Cheon; Lee, Hwan Soo; Ha, Pham Nhu Viet; Kim, Soon Young; Shin, Chang Ho; Kim, Jong Kyung

2007-01-01

EASYQAD had been previously developed by using MATLAB GUI (Graphical User Interface) in order to perform conveniently gamma and neutron shielding calculations at Hanyang University. It had been completed as version α of radiation shielding analysis code. In this study, EASYQAD was upgraded to version β with many additional functions and more user-friendly graphical interfaces. For general users to run it on Windows XP environment without any MATLAB installation, this version was developed into a standalone code system

Micromagnetic Code Development of Advanced Magnetic Structures Final Report CRADA No. TC-1561-98

Energy Technology Data Exchange (ETDEWEB)

Cerjan, Charles J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Shi, Xizeng [Read-Rite Corporation, Fremont, CA (United States)

2017-11-09

The specific goals of this project were to: Further develop the previously written micromagnetic code DADIMAG (DOE code release number 980017); Validate the code. The resulting code was expected to be more realistic and useful for simulations of magnetic structures of specific interest to Read-Rite programs. We also planned to further the code for use in internal LLNL programs. This project complemented LLNL CRADA TC-840-94 between LLNL and Read-Rite, which allowed for simulations of the advanced magnetic head development completed under the CRADA. TC-1561-98 was effective concurrently with LLNL non-exclusive copyright license (TL-1552-98) to Read-Rite for DADIMAG Version 2 executable code.

Status of development and verification of the CTFD code FLUBOX

International Nuclear Information System (INIS)

Graf, U.; Paradimitriou, P.

2004-01-01

The Computational Two-Fluid Dynamics (CTFD) code FLUBOX is developed at GRS for the multidimensional simulation of two-phase flows. FLUBOX will also be used as a multidimensional module for the German system code ATHLET. The Benchmark test cases of the European ASTAR project were used to verify the ability of the code FLUBOX to calculate typical two-phase flow phenomena and conditions: void and pressure wave propagation, phase transitions, countercurrent flows, sharp interface movements, compressible (vapour) and nearly incompressible (water) conditions, thermal and mechanical non-equilibrium, stiff source terms due to mass and heat transfer between the phases. Realistic simulations of two-phase require beside the pure conservation equations additional transport equations for the interfacial area, turbulent energy and dissipation. A transport equation for the interfacial area density covering the whole two-phase flow range is in development. First validation calculations are presented in the paper. Turbulent shear stress for two-phase flows will be modelled by the development of transport equations for the turbulent kinetic energy and the turbulent dissipation rate. The development of the transport equations is mainly based on first principles on bubbles or drops and is largely free from empiricism. (author)

Development of RESRAD probabilistic computer codes for NRC decommissioning and license termination applications

International Nuclear Information System (INIS)

Chen, S. Y.; Yu, C.; Mo, T.; Trottier, C.

2000-01-01

In 1999, the US Nuclear Regulatory Commission (NRC) tasked Argonne National Laboratory to modify the existing RESRAD and RESRAD-BUILD codes to perform probabilistic, site-specific dose analysis for use with the NRC's Standard Review Plan for demonstrating compliance with the license termination rule. The RESRAD codes have been developed by Argonne to support the US Department of Energy's (DOEs) cleanup efforts. Through more than a decade of application, the codes already have established a large user base in the nation and a rigorous QA support. The primary objectives of the NRC task are to: (1) extend the codes' capabilities to include probabilistic analysis, and (2) develop parameter distribution functions and perform probabilistic analysis with the codes. The new codes also contain user-friendly features specially designed with graphic-user interface. In October 2000, the revised RESRAD (version 6.0) and RESRAD-BUILD (version 3.0), together with the user's guide and relevant parameter information, have been developed and are made available to the general public via the Internet for use

Development of M3C code for Monte Carlo reactor physics criticality calculations

International Nuclear Information System (INIS)

Kumar, Anek; Kannan, Umasankari; Krishanani, P.D.

2015-06-01

The development of Monte Carlo code (M3C) for reactor design entails use of continuous energy nuclear data and Monte Carlo simulations for each of the neutron interaction processes. BARC has started a concentrated effort for developing a new general geometry continuous energy Monte Carlo code for reactor physics calculation indigenously. The code development required a comprehensive understanding of the basic continuous energy cross section sets. The important features of this code are treatment of heterogeneous lattices by general geometry, use of point cross sections along with unionized energy grid approach, thermal scattering model for low energy treatment, capability of handling the microscopic fuel particles dispersed randomly. The capability of handling the randomly dispersed microscopic fuel particles which is very useful for the modeling of High-Temperature Gas-Cooled reactor fuels which are composed of thousands of microscopic fuel particle (TRISO fuel particle), randomly dispersed in a graphite matrix. The Monte Carlo code for criticality calculation is a pioneering effort and has been used to study several types of lattices including cluster geometries. The code has been verified for its accuracy against more than 60 sample problems covering a wide range from simple (like spherical) to complex geometry (like PHWR lattice). Benchmark results show that the code performs quite well for the criticality calculation of the system. In this report, the current status of the code, features of the code, some of the benchmark results for the testing of the code and input preparation etc. are discussed. (author)

Development and Validation of A Nuclear Fuel Cycle Analysis Tool: A FUTURE Code

Energy Technology Data Exchange (ETDEWEB)

Kim, S. K.; Ko, W. I. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Yoon Hee [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2013-10-15

This paper presents the development and validation methods of the FUTURE (FUel cycle analysis Tool for nUcleaR Energy) code, which was developed for a dynamic material flow evaluation and economic analysis of the nuclear fuel cycle. This code enables an evaluation of a nuclear material flow and its economy for diverse nuclear fuel cycles based on a predictable scenario. The most notable virtue of this FUTURE code, which was developed using C and MICROSOFT SQL DBMS, is that a program user can design a nuclear fuel cycle process easily using a standard process on the canvas screen through a drag-and-drop method. From the user's point of view, this code is very easy to use thanks to its high flexibility. In addition, the new code also enables the maintenance of data integrity by constructing a database environment of the results of the nuclear fuel cycle analyses.

Development of in-vessel source term analysis code, tracer

International Nuclear Information System (INIS)

Miyagi, K.; Miyahara, S.

1996-01-01

Analyses of radionuclide transport in fuel failure accidents (generally referred to source terms) are considered to be important especially in the severe accident evaluation. The TRACER code has been developed to realistically predict the time dependent behavior of FPs and aerosols within the primary cooling system for wide range of fuel failure events. This paper presents the model description, results of validation study, the recent model advancement status of the code, and results of check out calculations under reactor conditions. (author)

Development of MATRA-LMR code α-version for LMR subchannel analysis

International Nuclear Information System (INIS)

Kim, Won Seok; Kim, Young Gyun; Kim, Young Gin

1998-05-01

Since the sodium boiling point is very high, maximum cladding and pin temperature are used for design limit condition in sodium cooled liquid metal reactor. It is necessary to predict accurately the core temperature distribution to increase the sodium coolant efficiency. Based on the MATRA code, which is developed for PWR analysis, MATRA-LMR is being developed for LMR. The major modification are as follows : A) The sodium properties table is implemented as subprogram in the code. B) Heat transfer coefficients are changed for LMR C) The pressure drop correlations are changed for more accurate calculations, which are Novendstern, Chiu-Rohsenow-Todreas, and Cheng-Todreas correlations. To assess the development status of MATRA-LMR code, calculations have been performed for ORNL 19 pin and EBR-II 61 pin tests. MATRA-LMR calculation results are also compared with the results obtained by the ALTHEN code, which uses more simplied thermal hydraulic model. The MATRA-LMR predictions are found to agree well to the measured values. The differences in results between MATRA-LMR and SLTHEN have occurred because SLTHEN code uses the very simplied thermal-hydraulic model to reduce computing time. MATRA-LMR can be used only for single assembly analysis, but it is planned to extend for multi-assembly calculation. (author). 18 refs., 8 tabs., 14 figs

The development of fluid codes for the laser compression of plasma

International Nuclear Information System (INIS)

Nicholas, D.J.

1982-08-01

Notes are given on the construction and use of simulation codes in plasma physics requiring only a limited background knowledge in numerical analysis and finite-difference techniques. The development of a 1-D Eulerian codes to source form is followed as an example. (U.K.)

Development of long-lived radionuclide transmutation technology - Development of a code system for core analysis of the transmutation reactors

Energy Technology Data Exchange (ETDEWEB)

Cho, Nam Zin; Kim, Yong Hee; Kim, Tae Hyung; Jo, Chang Keun; Park, Chang Je [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

1996-07-01

The objective of this study is to develop a code system for core analysis= of the critical transmutation reactors utilizing fast neutrons. Core characteristics of the transmutation reactors were identified and four codes, HANCELL for pincell calculation, PRISM and AFEN-H3D for core calculation, and MA{sub B}URN for depletion calculation, were developed. The pincell calculation code is based on one-dimensional collision probability method and may provide homogenized/condensed parameters of a pincell and also can homogenize the control assembly via a nonlinear iterative method. The core calculation codes, PRISM and AFEN-H3D, solve the multi-group, multi-dimensional neutron diffusion equations for a hexagonal geometry and they are based on the finite difference method and analytic function expansion nodal (AFEN) method, respectively. The MA{sub B}URN code san analyze the behavior of actinides and fission products in a reactor core. Through benchmarking, we confirmed that the newly developed codes provide accurate solutions. 30 refs., 10 tabs., 8 figs. (author)

Development of an object oriented lattice QCD code ''Bridge++''

International Nuclear Information System (INIS)

Ueda, S; Aoki, S; Aoyama, T; Kanaya, K; Taniguchi, Y; Matsufuru, H; Motoki, S; Namekawa, Y; Nemura, H; Ukita, N

2014-01-01

We are developing a new lattice QCD code set ''Bridge++'' aiming at extensible, readable, and portable workbench for QCD simulations, while keeping a high performance at the same time. Bridge++ covers conventional lattice actions and numerical algorithms. The code set is constructed in C++ with an object oriented programming. In this paper we describe fundamental ingredients of the code and the current status of development

Code Development of Radioactive Aerosol Scrubbing in Pool-Injection Zone

Energy Technology Data Exchange (ETDEWEB)

Jo, Hyun Joung; Ha, Kwang Soon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Jang, Dong Soon [Chungnam National University, Daejeon (Korea, Republic of)

2015-10-15

The pool scrubbing models were reviewed and an aerosol scrubbing code has been prepared to calculate decontamination factor through the injection zone. The developed code has been verified using the experimental results and evaluated parametrically on the input variables. In injection zone, the initial steam condensation was most effective mechanism for the aerosol removal, and the steam fraction and pool temperature were highly affected on the decontamination factor by initial steam condensation. The aerosol scrubbing code will be updated to evaluate the decontamination factor at rise zone and finally whole pool scrubber phenomena. If a severe accident occurs in a nuclear power plant (NPP), the aerosol and gaseous fission products might be produced in the reactor vessel, and then released to the environment after the containment failure. FCVS (Filtered Containment Venting System) is one of the severe accident mitigation systems for retaining the containment integrity by discharging the high-temperature and high-pressure fission products to the environment after passing through the filtration system. In general, the FCVS is categorized into two types, wet and dry types. The scrubbing pool could play an important role in the wet type FCVS because a large amount of aerosol is captured in the water pool. The pool scrubbing phenomena have been modelled and embedded in several computer codes, such as SPARC (Suppression Pool Aerosol Removal Code), BUSCA (BUbble Scrubbing Algorithm) and SUPRA (Suppression Pool Retention Analysis). These codes aim at simulating the pool scrubbing process and estimating the decontamination factors (DFs) of the radioactive aerosol and iodine gas in the water pool, which is defined as the ratio of initial mass of the specific radioactive material to final massy after passing through the water pool. The pool scrubbing models were reviewed and an aerosol scrubbing code has been prepared to calculate decontamination factor through the injection

CODE SWITCHING AND THE DEVELOPMENT OF LINGUISTIC SYSTEM OF SIMULTANEOUS BILINGUAL CHILDREN

Directory of Open Access Journals (Sweden)

Leni Amelia Suek

2017-11-01

Full Text Available Code switching and code mixing are the phenomena commonly seen done by a bilingual. This behavior is influenced by several aspects such as the linguistic system, sociolinguistics, pragmatics, and language competence of the bilingual. If children are able to distinguish two different languages since early age, they will be considered simultaneous bilinguals. They show that they develop multiple, rather than single, linguistic systems. However, it was understood that code switching and code mixing were due to the failure in using proper words, language features, and sociolinguistic competence. Yet, recent studies have shown that bilingual children are able to use both languages proficiently with no signs of confusion or failure in language use. This ability also does not hinder their cognitive development.

Development of GUI systems for the MIDAS code

International Nuclear Information System (INIS)

Kim, K.R.; Park, S.H.; Kim, D.H.

2004-01-01

MIDAS is being developed at KAERI based on MELCOR as an integrated severe accident analysis code with existing model modification and new model addition. MIDAS was restructured to avoid the pointer based variable referencing style of MELCOR, and enhanced the memory effectiveness using the dynamic allocation method of Fortran 90. This paper describes recent activities of developing the GUI environments for MIDAS code at KAERI. Up to now, we have developed the four PC-based subsystems, which are IEDIT, IPLOT, SATS and HyperKAMG. IEDIT is an input management system that can read MELCOR input files and display its information in the Window panels. Users can modify each item in the panel and the input file will be modified according to that changes. IPLOT is a simple plotting system that can draw MIDAS plot variables trend graphs. SATS is developed as a severe accident training simulator that can display nuclear plant behavior graphically. Moreover SATS provides several controllable pumps and valves which appeared in the severe accidence. Together with SATS and the online severe accident guidance HyperKAMG, combined properly, severe accident mitigation scenarios could be presented graphically and dramatically without any change of MELCOR inputs. GUI development as a part of a severe accident management program package, MIDAS. (author)

DEVELOPMENT OF SALES APPLICATION OF PREPAID ELECTRICITY VOUCHER BASED ON ANFROID PLATFORM USING QUICK RESPONSE CODE (QR CODE

Directory of Open Access Journals (Sweden)

Ricky Akbar

2017-09-01

Full Text Available Perusahaan Listrik Negara (PLN has implemented a smart electricity system or prepaid electricity. The customers pay the electricity voucher first before use the electricity. The token contained in electricity voucher that has been purchased by the customer is inserted into the Meter Prabayar (MPB installed in the location of customers. When a customer purchases a voucher, it will get a receipt that contains all of the customer's identity and the 20-digit of voucher code (token to be entered into MPB as a substitute for electrical energy credit. Receipts obtained by the customer is certainly vulnerable to loss, or hijacked by unresponsible parties. In this study, authors designed and develop an android based application by utilizing QR code technology as a replacement for the receipt of prepaid electricity credit which contains the identity of the customer and the 20-digit voucher code. The application is developed by implemented waterfall methodology. The implementation process of the waterfall methods used, are (1 analysis of functional requirement of the system by conducting a preliminary study and data collection based on field studies and literature, (2 system design by using UML diagrams and Business Process Model Notation (BPMN and Entity Relationship diagram (ERD, (3 design implementation by using OOP (Object Oriented programming technique. Web application is developed by using laravel PHP framework and database MySQL while mobile application is developed by using B4A (4 developed system is tested by using blackbox method testing. Final result of this research is a Web and mobile applications for the sale of electricityvoucher by QR Code technology.

Development of best estimate auditing code for CANDU thermal-hydraulic safety analysis

Energy Technology Data Exchange (ETDEWEB)

Chung, Bub Dong; Lee, Won Jae; Hwang, Moon Kyu; Lim, Hong Sik [Korea Atomic Energy Research Institute, Taejeon (Korea)

2002-04-01

The main purpose of this study is to develop a thermal hydraulic auditing code for the CANDU reactor, modifying the model of existing PWR auditing tool, i.e. RELAP5/MOD3.The study was performed by reconsideration of the previous code assessment works and phenomena identification for essential accident scenario. Improvement areas of model development for auditing tool were identified based on the code comparison and PIRT results. Nine models have been improved significantly for the analysis of LOCA and Mon LOCA event. Conceptual problem or separate effect assessment have been performed to verify the model improvement. The linking calculation with CONTAIN 2.0 has been also enabled to establish the unified auditing code system. Analysis for the CANDU plant real transient and hypothetical LOCA bas been performed using the improved version. It has been concluded that the developed version can be utilized for the auditing analysis of LOCA and non-LOCA event for the CANDU reactor. 25 refs., 84 figs., 36 tabs. (Author)

DEVELOPMENT AND VALIDATION OF A NUCLEAR FUEL CYCLE ANALYSIS TOOL: A FUTURE CODE

Directory of Open Access Journals (Sweden)

S.K. KIM

2013-10-01

Full Text Available This paper presents the development and validation methods of the FUTURE (FUel cycle analysis Tool for nUcleaR Energy code, which was developed for a dynamic material flow evaluation and economic analysis of the nuclear fuel cycle. This code enables an evaluation of a nuclear material flow and its economy for diverse nuclear fuel cycles based on a predictable scenario. The most notable virtue of this FUTURE code, which was developed using C# and MICROSOFT SQL DBMS, is that a program user can design a nuclear fuel cycle process easily using a standard process on the canvas screen through a drag-and-drop method. From the user's point of view, this code is very easy to use thanks to its high flexibility. In addition, the new code also enables the maintenance of data integrity by constructing a database environment of the results of the nuclear fuel cycle analyses.

The development and application of a sub-channel code in ocean environment

International Nuclear Information System (INIS)

Wu, Pan; Shan, Jianqiang; Xiang, Xiong; Zhang, Bo; Gou, Junli; Zhang, Bin

2016-01-01

Highlights: • A sub-channel code named ATHAS/OE is developed for nuclear reactors in ocean environment. • ATHAS/OE is verified by another modified sub-channel code based on COBRA-IV. • ATHAS/OE is used to analyze thermal hydraulic of a typical SMR in heaving and rolling motion. • Calculation results show that ocean condition affect the thermal hydraulic of a reactor significantly. - Abstract: An upgraded version of ATHAS sub-channel code ATHAS/OE is developed for the investigation of the thermal hydraulic behavior of nuclear reactor core in ocean environment with consideration of heaving and rolling motion effect. The code is verified by another modified sub-channel code based on COBRA-IV and used to analyze the thermal hydraulic characteristics of a typical SMR under heaving and rolling motion condition. The calculation results show that the heaving and rolling motion affect the thermal hydraulic behavior of a reactor significantly.

Development of seismic analysis model for HTGR core on commercial FEM code

International Nuclear Information System (INIS)

Tsuji, Nobumasa; Ohashi, Kazutaka

2015-01-01

The aftermath of the Great East Japan Earthquake prods to revise the design basis earthquake intensity severely. In aseismic design of block-type HTGR, the securement of structural integrity of core blocks and other structures which are made of graphite become more important. For the aseismic design of block-type HTGR, it is necessary to predict the motion of core blocks which are collided with adjacent blocks. Some seismic analysis codes have been developed in 1970s, but these codes are special purpose-built codes and have poor collaboration with other structural analysis code. We develop the vertical 2 dimensional analytical model on multi-purpose commercial FEM code, which take into account the multiple impacts and friction between block interfaces and rocking motion on contact with dowel pins of the HTGR core by using contact elements. This model is verified by comparison with the experimental results of 12 column vertical slice vibration test. (author)

Development of non-linear vibration analysis code for CANDU fuelling machine

International Nuclear Information System (INIS)

Murakami, Hajime; Hirai, Takeshi; Horikoshi, Kiyomi; Mizukoshi, Kaoru; Takenaka, Yasuo; Suzuki, Norio.

1988-01-01

This paper describes the development of a non-linear, dynamic analysis code for the CANDU 600 fuelling machine (F-M), which includes a number of non-linearities such as gap with or without Coulomb friction, special multi-linear spring connections, etc. The capabilities and features of the code and the mathematical treatment for the non-linearities are explained. The modeling and numerical methodology for the non-linearities employed in the code are verified experimentally. Finally, the simulation analyses for the full-scale F-M vibration testing are carried out, and the applicability of the code to such multi-degree of freedom systems as F-M is demonstrated. (author)

Development of a PC code package for the analysis of research and power reactors

International Nuclear Information System (INIS)

Urli, N.

1992-06-01

Computer codes available for performing reactor physics calculations for nuclear research reactors and power reactors are normally suited for running on mainframe computers. With the fast development in speed and memory of the PCs and affordable prices it became feasible to develop PC versions of commonly used codes. The present work performed under an IAEA sponsored research contract has successfully developed a code package for running on a PC. This package includes a cross-section generating code PSU-LEOPARD and 2D and 1D spatial diffusion codes, MCRAC and MCYC 1D. For adapting PSU-LEOPARD for a PC, the binary library has been reorganized to decimal form, upgraded to FORTRAN-77 standard and arrays and subroutines reorganized to conform to PC compiler. Similarly PC version of MCRAC for FORTRAN-77 and 1D code MCYC 1D have been developed. Tests, verification and bench mark results show excellent agreement with the results obtained from mainframe calculations. The execution speeds are also very satisfactory. 12 refs, 4 figs, 3 tabs

Development of an integrated thermal-hydraulics capability incorporating RELAP5 and PANTHER neutronics code

Energy Technology Data Exchange (ETDEWEB)

Page, R.; Jones, J.R.

1997-07-01

Ensuring that safety analysis needs are met in the future is likely to lead to the development of new codes and the further development of existing codes. It is therefore advantageous to define standards for data interfaces and to develop software interfacing techniques which can readily accommodate changes when they are made. Defining interface standards is beneficial but is necessarily restricted in application if future requirements are not known in detail. Code interfacing methods are of particular relevance with the move towards automatic grid frequency response operation where the integration of plant dynamic, core follow and fault study calculation tools is considered advantageous. This paper describes the background and features of a new code TALINK (Transient Analysis code LINKage program) used to provide a flexible interface to link the RELAP5 thermal hydraulics code with the PANTHER neutron kinetics and the SIBDYM whole plant dynamic modelling codes used by Nuclear Electric. The complete package enables the codes to be executed in parallel and provides an integrated whole plant thermal-hydraulics and neutron kinetics model. In addition the paper discusses the capabilities and pedigree of the component codes used to form the integrated transient analysis package and the details of the calculation of a postulated Sizewell `B` Loss of offsite power fault transient.

Development of an integrated thermal-hydraulics capability incorporating RELAP5 and PANTHER neutronics code

International Nuclear Information System (INIS)

Page, R.; Jones, J.R.

1997-01-01

Ensuring that safety analysis needs are met in the future is likely to lead to the development of new codes and the further development of existing codes. It is therefore advantageous to define standards for data interfaces and to develop software interfacing techniques which can readily accommodate changes when they are made. Defining interface standards is beneficial but is necessarily restricted in application if future requirements are not known in detail. Code interfacing methods are of particular relevance with the move towards automatic grid frequency response operation where the integration of plant dynamic, core follow and fault study calculation tools is considered advantageous. This paper describes the background and features of a new code TALINK (Transient Analysis code LINKage program) used to provide a flexible interface to link the RELAP5 thermal hydraulics code with the PANTHER neutron kinetics and the SIBDYM whole plant dynamic modelling codes used by Nuclear Electric. The complete package enables the codes to be executed in parallel and provides an integrated whole plant thermal-hydraulics and neutron kinetics model. In addition the paper discusses the capabilities and pedigree of the component codes used to form the integrated transient analysis package and the details of the calculation of a postulated Sizewell 'B' Loss of offsite power fault transient

Methodology, status and plans for development and assessment of the code ATHLET

Energy Technology Data Exchange (ETDEWEB)

Teschendorff, V.; Austregesilo, H.; Lerchl, G. [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH Forschungsgelaende, Garching (Germany)

1997-07-01

The thermal-hydraulic computer code ATHLET (Analysis of THermal-hydraulics of LEaks and Transients) is being developed by the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) for the analysis of anticipated and abnormal plant transients, small and intermediate leaks as well as large breaks in light water reactors. The aim of the code development is to cover the whole spectrum of design basis and beyond design basis accidents (without core degradation) for PWRs and BWRs with only one code. The main code features are: advanced thermal-hydraulics; modular code architecture; separation between physical models and numerical methods; pre- and post-processing tools; portability. The code has features that are of special interest for applications to small leaks and transients with accident management, e.g. initialization by a steady-state calculation, full-range drift-flux model, dynamic mixture level tracking. The General Control Simulation Module of ATHLET is a flexible tool for the simulation of the balance-of-plant and control systems including the various operator actions in the course of accident sequences with AM measures. The code development is accompained by a systematic and comprehensive validation program. A large number of integral experiments and separate effect tests, including the major International Standard Problems, have been calculated by GRS and by independent organizations. The ATHLET validation matrix is a well balanced set of integral and separate effects tests derived from the CSNI proposal emphasizing, however, the German combined ECC injection system which was investigated in the UPTF, PKL and LOBI test facilities.

Methodology, status and plans for development and assessment of the code ATHLET

International Nuclear Information System (INIS)

Teschendorff, V.; Austregesilo, H.; Lerchl, G.

1997-01-01

The thermal-hydraulic computer code ATHLET (Analysis of THermal-hydraulics of LEaks and Transients) is being developed by the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) for the analysis of anticipated and abnormal plant transients, small and intermediate leaks as well as large breaks in light water reactors. The aim of the code development is to cover the whole spectrum of design basis and beyond design basis accidents (without core degradation) for PWRs and BWRs with only one code. The main code features are: advanced thermal-hydraulics; modular code architecture; separation between physical models and numerical methods; pre- and post-processing tools; portability. The code has features that are of special interest for applications to small leaks and transients with accident management, e.g. initialization by a steady-state calculation, full-range drift-flux model, dynamic mixture level tracking. The General Control Simulation Module of ATHLET is a flexible tool for the simulation of the balance-of-plant and control systems including the various operator actions in the course of accident sequences with AM measures. The code development is accompained by a systematic and comprehensive validation program. A large number of integral experiments and separate effect tests, including the major International Standard Problems, have been calculated by GRS and by independent organizations. The ATHLET validation matrix is a well balanced set of integral and separate effects tests derived from the CSNI proposal emphasizing, however, the German combined ECC injection system which was investigated in the UPTF, PKL and LOBI test facilities

Proceedings of the 8th topical meeting on nuclear code development

International Nuclear Information System (INIS)

1993-03-01

The 8th Topical Meeting on Nuclear Code Development, organized by Committee on Reactor Physics and Nuclear Codes Committee of Japan Atomic Energy Research Institute (JAERI), was held at Tokai Research Establishment of JAERI, on 11th and 12th of November, 1992. In the meeting, 14 papers were presented on the topics of (1) the next generation nuclear reactor design system and (2) advances of the nuclear fuel reprocessing safety analysis codes. These papers are compiled in this proceedings. (author)

Development of a computer code for Dalat research reactor transient analysis

International Nuclear Information System (INIS)

Le Vinh Vinh; Nguyen Thai Sinh; Huynh Ton Nghiem; Luong Ba Vien; Pham Van Lam; Nguyen Kien Cuong

2003-01-01

DRSIM (Dalat Reactor SIMulation) computer code has been developed for Dalat reactor transient analysis. It is basically a coupled neutronics-hydrodynamics-heat transfer code employing point kinetics, one dimensional hydrodynamics and one dimensional heat transfer. The work was financed by VAEC and DNRI in the framework of institutional R and D programme. Some transient problems related to reactivity and loss of coolant flow was carried out by DRSIM using temperature and void coefficients calculated by WIMS and HEXNOD2D codes. (author)

Development of 3D CFD code based on structured non-orthogonal grids

International Nuclear Information System (INIS)

Vaidya, Abhijeet Mohan; Maheshwari, Naresh Kumar; Rama Rao, A.

2016-01-01

Most of the nuclear industry problems involve complex geometries. Solution of flow and heat transfer over complex geometries is a very important requirement for designing new reactor systems. Hence development of a general purpose three dimensional (3D) CFD code is undertaken. For handling complex shape of computational domain, implementation on structured non-orthogonal coordinates is being done. The code is validated by comparing its results for 3D inclined lid driven cavity at different inclination angles and Reynolds numbers with OpenFOAM results. This paper contains formulation and validation of the new code developed. (author)

Code development of the national hemovigilance system and expansion strategies for hospital blood banks

Directory of Open Access Journals (Sweden)

Kim Jeongeun

2012-01-01

Full Text Available Objectives : The aims of this study were to develop reportable event codes that are applicable to the national hemovigilance systems for hospital blood banks, and to present expansion strategies for the blood banks. Materials and Methods : The data were obtained from a literature review and expert consultation, followed by adding to and revising the established hemovigilance code system and guidelines to develop reportable event codes for hospital blood banks. The Medical Error Reporting System-Transfusion Medicine developed in the US and other codes of reportable events were added to the Korean version of the Biologic Products Deviation Report (BPDR developed by the Korean Red Cross Blood Safety Administration, then using these codes, mapping work was conducted. We deduced outcomes suitable for practice, referred to the results of the advisory councils, and conducted a survey with experts and blood banks practitioners. Results : We developed reportable event codes that were applicable to hospital blood banks and could cover blood safety - from blood product safety to blood transfusion safety - and also presented expansion strategies for hospital blood banks. Conclusion : It was necessary to add 10 major categories to the blood transfusion safety stage and 97 reportable event codes to the blood safety stage. Contextualized solutions were presented on 9 categories of expansion strategies of hemovigilance system for the hospital blood banks.

Development and validation of a nodal code for core calculation

International Nuclear Information System (INIS)

Nowakowski, Pedro Mariano

2004-01-01

The code RHENO solves the multigroup three-dimensional diffusion equation using a nodal method of polynomial expansion.A comparative study has been made between this code and present internationals nodal diffusion codes, resulting that the RHENO is up to date.The RHENO has been integrated to a calculation line and has been extend to make burnup calculations.Two methods for pin power reconstruction were developed: modulation and imbedded. The modulation method has been implemented in a program, while the implementation of the imbedded method will be concluded shortly.The validation carried out (that includes experimental data of a MPR) show very good results and calculation efficiency

Code development for eigenvalue total sensitivity analysis and total uncertainty analysis

International Nuclear Information System (INIS)

Wan, Chenghui; Cao, Liangzhi; Wu, Hongchun; Zu, Tiejun; Shen, Wei

2015-01-01

Highlights: • We develop a new code for total sensitivity and uncertainty analysis. • The implicit effects of cross sections can be considered. • The results of our code agree well with TSUNAMI-1D. • Detailed analysis for origins of implicit effects is performed. - Abstract: The uncertainties of multigroup cross sections notably impact eigenvalue of neutron-transport equation. We report on a total sensitivity analysis and total uncertainty analysis code named UNICORN that has been developed by applying the direct numerical perturbation method and statistical sampling method. In order to consider the contributions of various basic cross sections and the implicit effects which are indirect results of multigroup cross sections through resonance self-shielding calculation, an improved multigroup cross-section perturbation model is developed. The DRAGON 4.0 code, with application of WIMSD-4 format library, is used by UNICORN to carry out the resonance self-shielding and neutron-transport calculations. In addition, the bootstrap technique has been applied to the statistical sampling method in UNICORN to obtain much steadier and more reliable uncertainty results. The UNICORN code has been verified against TSUNAMI-1D by analyzing the case of TMI-1 pin-cell. The numerical results show that the total uncertainty of eigenvalue caused by cross sections can reach up to be about 0.72%. Therefore the contributions of the basic cross sections and their implicit effects are not negligible

Recent developments in seismic analysis in the code Aster; Les developpements recents en analyse sismique dans le code aster

Energy Technology Data Exchange (ETDEWEB)

Guihot, P.; Devesa, G.; Dumond, A.; Panet, M.; Waeckel, F.

1996-12-31

Progress in the field of seismic qualification and design methods made these last few years allows physical phenomena actually in play to be better considered, while cutting down the conservatism associated with some simplified design methods. So following the change in methods and developing the most advantageous ones among them contributes to the process of the seismic margins assessment and the preparation of new design tools for future series. In this paper, the main developments and improvements in methods which have been made these last two years in the Code Aster, in order to improve seismic calculation methods and seismic margin assessment are presented. The first development relates to making the MISS3D soil structure interaction code available, thanks to an interface made with the Code Aster. The second relates to the possibility of making modal basis time calculations on multi-supported structures by considering local non linearities like impact, friction or squeeze fluid forces. Recent developments in random dynamics and postprocessing devoted to earthquake designs are then mentioned. Three applications of these developments are then ut forward. The first application relates to a test case for soil structure interaction design using MISS3D-Aster coupling. The second is a test case for a multi-supported structure. The last application, more for manufacturing, refers to seismic qualification of Main Live Steam stop valves. First results of the independent validation of the Code Aster seismic design functionalities, which provide and improve the quality of software, are also recalled. (authors). 11 refs.

Development of three-dimensional transport code by the double finite element method

International Nuclear Information System (INIS)

Fujimura, Toichiro

1985-01-01

Development of a three-dimensional neutron transport code by the double finite element method is described. Both of the Galerkin and variational methods are adopted to solve the problem, and then the characteristics of them are compared. Computational results of the collocation method, developed as a technique for the vaviational one, are illustrated in comparison with those of an Ssub(n) code. (author)

Development of environmental dose assessment system (EDAS) code of PC version

Energy Technology Data Exchange (ETDEWEB)

Taki, Mitsumasa; Kikuchi, Masamitsu; Kobayashi, Hideo; Yamaguchi, Takenori [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2003-05-01

A computer code (EDAS) was developed to assess the public dose for the safety assessment to get the license of nuclear reactor operation. This code system is used for the safety analysis of public around the nuclear reactor in normal operation and severe accident. This code was revised and composed for personal computer user according to the Nuclear Safety Guidelines reflected the ICRP1990 recommendation. These guidelines are revised by Nuclear Safety Commission on March, 2001, which are 'Weather analysis guideline for the safety assessment of nuclear power reactor', 'Public dose around the facility assessment guideline corresponding to the objective value for nuclear power light water reactor' and 'Public dose assessment guideline for safety review of nuclear power light water reactor'. This code has been already opened for public user by JAERI, and English version code and user manual are also prepared. This English version code is helpful for international cooperation concerning the nuclear safety assessment with JAERI. (author)

Development of environmental dose assessment system (EDAS) code of PC version

CERN Document Server

Taki, M; Kobayashi, H; Yamaguchi, T

2003-01-01

A computer code (EDAS) was developed to assess the public dose for the safety assessment to get the license of nuclear reactor operation. This code system is used for the safety analysis of public around the nuclear reactor in normal operation and severe accident. This code was revised and composed for personal computer user according to the Nuclear Safety Guidelines reflected the ICRP1990 recommendation. These guidelines are revised by Nuclear Safety Commission on March, 2001, which are 'Weather analysis guideline for the safety assessment of nuclear power reactor', 'Public dose around the facility assessment guideline corresponding to the objective value for nuclear power light water reactor' and 'Public dose assessment guideline for safety review of nuclear power light water reactor'. This code has been already opened for public user by JAERI, and English version code and user manual are also prepared. This English version code is helpful for international cooperation concerning the nuclear safety assessme...

Computer codes developed in FRG to analyse hypothetical meltdown accidents

International Nuclear Information System (INIS)

Hassmann, K.; Hosemann, J.P.; Koerber, H.; Reineke, H.

1978-01-01

It is the purpose of this paper to give the status of all significant computer codes developed in the core melt-down project which is incorporated in the light water reactor safety research program of the Federal Ministry of Research and Technology. For standard pressurized water reactors, results of some computer codes will be presented, describing the course and the duration of the hypothetical core meltdown accident. (author)

Current status of the reactor physics code WIMS and recent developments

International Nuclear Information System (INIS)

Lindley, B.A.; Hosking, J.G.; Smith, P.J.; Powney, D.J.; Tollit, B.S.; Newton, T.D.; Perry, R.; Ware, T.C.; Smith, P.N.

2017-01-01

Highlights: • The current status of the WIMS reactor physics code is presented. • Applications range from 2D lattice calculations up to 3D whole core geometries. • Gamma transport and thermal-hydraulic feedback models added. • Calculations methodologies described for several Gen II, III and IV reactor types. - Abstract: The WIMS modular reactor physics code has been under continuous development for over fifty years. This paper discusses the current status of WIMS and recent developments, in particular developments to the resonance shielding methodology and 3D transport solvers. Traditionally, WIMS is used to perform 2D lattice calculations, typically to generate homogenized reactor physics parameters for a whole core code such as PANTHER. However, with increasing computational resources there has been a growing trend for performing transport calculations on larger problems, up to and including 3D full core models. To this end, a number of the WIMS modules have been parallelised to allow efficient performance for whole core calculations, and WIMS includes a 3D method of characteristics solver with reflective and once-through tracking methods, which can be used to analyse problems of varying size and complexity. A time-dependent flux solver has been incorporated and thermal-hydraulic modelling capability is also being added to allow steady-state and transient coupled calculations to be performed. WIMS has been validated against a range of experimental data and other codes, in particular for water and graphite moderated thermal reactors. Future developments will include improved parallelization, enhancing the thermal-hydraulic feedback models and validating the WIMS/PANTHER code system for BWRs and fast reactors.

Development status of the lattice physics code in COSINE project

Energy Technology Data Exchange (ETDEWEB)

Chen, Y.; Yu, H.; Li, S.; Liu, Z.; Yan, Y. [State Nuclear Power Software Development Center, SNPTC, National Energy Key Laboratory of Nuclear Power Software NEKLS, North Third Ring Road, Beijing 100029 (China)

2013-07-01

LATC is an essential part of COSINE code package, which stands for Core and System Integrated Engine for design and analysis. LATC performs 2D multi-group assembly transport calculation and generates few group constants and the required cross-section data for CORE, the core simulator code. LATC is designed to have the capability of modeling the API 000 series assemblies. The development is a continuously improved process. Currently, LATC uses well-proven technology to achieve the key functions. In the next stage, more advanced methods and modules will be implemented. At present, WIMS and WIMS improved format library could be read in LATC code. For resonance calculation, equivalent relation with rational approximations is utilized. For transport calculation, two options are available. One choice is collision probability method in cell homogenization while discrete coordinate method in assembly homogenization, the other is method of characteristics in assembly homogenization directly. For depletion calculation, an improved linear rate 'constant power' depletion method has been developed. (authors)

Development status of the lattice physics code in COSINE project

International Nuclear Information System (INIS)

Chen, Y.; Yu, H.; Li, S.; Liu, Z.; Yan, Y.

2013-01-01

LATC is an essential part of COSINE code package, which stands for Core and System Integrated Engine for design and analysis. LATC performs 2D multi-group assembly transport calculation and generates few group constants and the required cross-section data for CORE, the core simulator code. LATC is designed to have the capability of modeling the API 000 series assemblies. The development is a continuously improved process. Currently, LATC uses well-proven technology to achieve the key functions. In the next stage, more advanced methods and modules will be implemented. At present, WIMS and WIMS improved format library could be read in LATC code. For resonance calculation, equivalent relation with rational approximations is utilized. For transport calculation, two options are available. One choice is collision probability method in cell homogenization while discrete coordinate method in assembly homogenization, the other is method of characteristics in assembly homogenization directly. For depletion calculation, an improved linear rate 'constant power' depletion method has been developed. (authors)

Conceptual Approach to Forming the Basic Code of Neo-Industrial Development of a Region

Directory of Open Access Journals (Sweden)

Elena Leonidovna Andreeva

2017-09-01

Full Text Available In the article, the authors propose the conceptual fundamentals of the “code approach” to the regional neo-industrial development. The purpose of the research is to reveal the essence of the transition to a new type of industrial and economic relations through a prism of “genetic codes” of the region. We consider these codes as a system of the “racial memory” of a territory, which determines the specificity and features of neo-industrialization realization. We substantiated the hypothesis about the influence of the “genetic codes” of the region on the effectiveness of the neo-industrialization. We have defined the participants, or else the carriers of the codes in the transformation of regional inheritance for the stimulation of the neoindustrial development of region’s economy. The subject matter of the research is the distinctive features of the functioning of the determinative region’s codes. Their content determines the socio-economic specificity of the region and the features of innovative, informational, value-based and competence-based development of the territory. The determinative codes generate the dynamic codes of the region, which are understood as their derivatives. They have a high probability of occurrence, higher speed of development and distribution, internal forces that make possible the self-development of the region. The scientific contribution is the substantiation of the basic code of the regional neo-industrial development. It represents the evolutionary accumulation of the rapid changes of its innovative, informational, value-based and competence-based codes stimulating the generation and implementation of new ideas regarding to economic entities adapted to the historical and cultural conditions. The article presents the code model of neo-industrial development of the region described by formulas. We applied the system analysis methods, historical and civilization approaches, evolutionary and

Development of a code for the isotopic analysis of Uranium

Energy Technology Data Exchange (ETDEWEB)

Kim, J. H.; Kang, M. Y.; Kim, Jinhyeong; Choi, H. D. [Seoul National Univ., Seoul (Korea, Republic of)

2013-05-15

To strengthen the national nuclear nonproliferation regime by an establishment of nuclear forensic system, the techniques for nuclear material analysis and the categorization of important domestic nuclear materials are being developed. MGAU and FRAM are commercial software for the isotopic analysis of Uranium by using γ-spectroscopy, but the diversity of detection geometry and some effects - self attenuation, coincidence summing, etc. - suggest an analysis tool under continual improvement and modification. Hence, developing another code for HPGe γ- and x-ray spectrum analysis is started in this study. The analysis of the 87-101 keV region of Uranium spectrum is attempted based on the isotopic responses similar to those developed in MGAU. The code for isotopic analysis of Uranium is started from a fitting.

Development of a new generation solid rocket motor ignition computer code

Science.gov (United States)

Foster, Winfred A., Jr.; Jenkins, Rhonald M.; Ciucci, Alessandro; Johnson, Shelby D.

1994-01-01

This report presents the results of experimental and numerical investigations of the flow field in the head-end star grain slots of the Space Shuttle Solid Rocket Motor. This work provided the basis for the development of an improved solid rocket motor ignition transient code which is also described in this report. The correlation between the experimental and numerical results is excellent and provides a firm basis for the development of a fully three-dimensional solid rocket motor ignition transient computer code.

ER@CEBAF: Modeling code developments

Energy Technology Data Exchange (ETDEWEB)

Meot, F. [Brookhaven National Lab. (BNL), Upton, NY (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Roblin, Y. [Brookhaven National Lab. (BNL), Upton, NY (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

2016-04-13

A proposal for a multiple-pass, high-energy, energy-recovery experiment using CEBAF is under preparation in the frame of a JLab-BNL collaboration. In view of beam dynamics investigations regarding this project, in addition to the existing model in use in Elegant a version of CEBAF is developed in the stepwise ray-tracing code Zgoubi, Beyond the ER experiment, it is also planned to use the latter for the study of polarization transport in the presence of synchrotron radiation, down to Hall D line where a 12 GeV polarized beam can be delivered. This Note briefly reports on the preliminary steps, and preliminary outcomes, based on an Elegant to Zgoubi translation.

Further development of the computer code ATHLET-CD

International Nuclear Information System (INIS)

Weber, Sebastian; Austregesilo, Henrique; Bals, Christine; Band, Sebastian; Hollands, Thorsten; Koellein, Carsten; Lovasz, Liviusz; Pandazis, Peter; Schubert, Johann-Dietrich; Sonnenkalb, Martin

2016-10-01

In the framework of the reactor safety research program sponsored by the German Federal Ministry for Economic Affairs and Energy (BMWi), the computer code system ATHLET/ATHLET-CD has been further developed as an analysis tool for the simulation of accidents in nuclear power plants with pressurized and boiling water reactors as well as for the evaluation of accident management procedures. The main objective was to provide a mechanistic analysis tool for best estimate calculations of transients, accidents, and severe accidents with core degradation in light water reactors. With the continued development, the capability of the code system has been largely improved, allowing best estimate calculations of design and beyond design base accidents, and the simulation of advanced core degradation with enhanced model extent in a reasonable calculation time. ATHLET comprises inter alia a 6-equation model, models for the simulation of non-condensable gases and tracking of boron concentration, as well as additional component and process models for the complete system simulation. Among numerous model improvements, the code application has been extended to super critical pressures. The mechanistic description of the dynamic development of flow regimes on the basis of a transport equation for the interface area has been further developed. This ATHLET version is completely integrated in ATHLET-CD. ATHLET-CD further comprises dedicated models for the simulation of fuel and control assembly degradation for both pressurized and boiling water reactors, debris bed with melting in the core region, as well as fission product and aerosol release and transport in the cooling system, inclusive of decay of nuclide inventories and of chemical reactions in the gas phase. The continued development also concerned the modelling of absorber material release, of melting, melt relocation and freezing, and the interaction with the wall of the reactor pressure vessel. The following models were newly

Long non-coding RNAs and mRNAs profiling during spleen development in pig.

Science.gov (United States)

Che, Tiandong; Li, Diyan; Jin, Long; Fu, Yuhua; Liu, Yingkai; Liu, Pengliang; Wang, Yixin; Tang, Qianzi; Ma, Jideng; Wang, Xun; Jiang, Anan; Li, Xuewei; Li, Mingzhou

2018-01-01

Genome-wide transcriptomic studies in humans and mice have become extensive and mature. However, a comprehensive and systematic understanding of protein-coding genes and long non-coding RNAs (lncRNAs) expressed during pig spleen development has not been achieved. LncRNAs are known to participate in regulatory networks for an array of biological processes. Here, we constructed 18 RNA libraries from developing fetal pig spleen (55 days before birth), postnatal pig spleens (0, 30, 180 days and 2 years after birth), and the samples from the 2-year-old Wild Boar. A total of 15,040 lncRNA transcripts were identified among these samples. We found that the temporal expression pattern of lncRNAs was more restricted than observed for protein-coding genes. Time-series analysis showed two large modules for protein-coding genes and lncRNAs. The up-regulated module was enriched for genes related to immune and inflammatory function, while the down-regulated module was enriched for cell proliferation processes such as cell division and DNA replication. Co-expression networks indicated the functional relatedness between protein-coding genes and lncRNAs, which were enriched for similar functions over the series of time points examined. We identified numerous differentially expressed protein-coding genes and lncRNAs in all five developmental stages. Notably, ceruloplasmin precursor (CP), a protein-coding gene participating in antioxidant and iron transport processes, was differentially expressed in all stages. This study provides the first catalog of the developing pig spleen, and contributes to a fuller understanding of the molecular mechanisms underpinning mammalian spleen development.

Development and assessment of best estimate integrated safety analysis code

International Nuclear Information System (INIS)

Chung, Bub Dong; Lee, Young Jin; Hwang, Moon Kyu

2007-03-01

Improvement of the integrated safety analysis code MARS3.0 has been carried out and a multi-D safety analysis application system has been established. Iterative matrix solver and parallel processing algorithm have been introduced, and a LINUX version has been generated to enable MARS to run in cluster PCs. MARS variables and sub-routines have been reformed and modularised to simplify code maintenance. Model uncertainty analyses have been performed for THTF, FLECHT, NEPTUN, and LOFT experiments as well as APR1400 plant. Participations in international cooperation research projects such as OECD BEMUSE, SETH, PKL, BFBT, and TMI-2 have been actively pursued as part of code assessment efforts. The assessment, evaluation and experimental data obtained through international cooperation projects have been registered and maintained in the T/H Databank. Multi-D analyses of APR1400 LBLOCA, DVI Break, SLB, and SGTR have been carried out as a part of application efforts in multi-D safety analysis. GUI based 3D input generator has been developed for user convenience. Operation of the MARS Users Group (MUG) was continued and through MUG, the technology has been transferred to 24 organisations. A set of 4 volumes of user manuals has been compiled and the correction reports for the code errors reported during MARS development have been published

Development and assessment of best estimate integrated safety analysis code

Energy Technology Data Exchange (ETDEWEB)

Chung, Bub Dong; Lee, Young Jin; Hwang, Moon Kyu (and others)

2007-03-15

Improvement of the integrated safety analysis code MARS3.0 has been carried out and a multi-D safety analysis application system has been established. Iterative matrix solver and parallel processing algorithm have been introduced, and a LINUX version has been generated to enable MARS to run in cluster PCs. MARS variables and sub-routines have been reformed and modularised to simplify code maintenance. Model uncertainty analyses have been performed for THTF, FLECHT, NEPTUN, and LOFT experiments as well as APR1400 plant. Participations in international cooperation research projects such as OECD BEMUSE, SETH, PKL, BFBT, and TMI-2 have been actively pursued as part of code assessment efforts. The assessment, evaluation and experimental data obtained through international cooperation projects have been registered and maintained in the T/H Databank. Multi-D analyses of APR1400 LBLOCA, DVI Break, SLB, and SGTR have been carried out as a part of application efforts in multi-D safety analysis. GUI based 3D input generator has been developed for user convenience. Operation of the MARS Users Group (MUG) was continued and through MUG, the technology has been transferred to 24 organisations. A set of 4 volumes of user manuals has been compiled and the correction reports for the code errors reported during MARS development have been published.

Scientific codes developed and used at GRS. Nuclear simulation chain

Energy Technology Data Exchange (ETDEWEB)

Schaffrath, Andreas; Sonnenkalb, Martin; Sievers, Juergen; Luther, Wolfgang; Velkov, Kiril [Gesellschaft fuer Anlagen und Reaktorsicherheit (GRS) gGmbH, Garching/Muenchen (Germany). Forschungszentrum

2016-05-15

Over 60 technical experts of the reactor safety research division of the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH are developing and validating reliable methods and computer codes - summarized under the term nuclear simulation chain - for the safety-related assessment for all types of nuclear power plants (NPP) and other nuclear facilities considering the current state of science and technology. This nuclear simulation chain has to be able to simulate and assess all relevant physical processes and phenomena for all operating states and (severe) accidents. In the present contribution, the nuclear simulation chain developed and applied by GRS as well as selected examples of its application are presented. The latter demonstrate impressively the width of its scope and its performance. The GRS codes can be passed on request to other (national as well as international) organizations. This contributes to a worldwide increase of the nuclear safety standards. The code transfer is especially important for developing and emerging countries lacking the financial means and/or the necessary know-how for this purpose. At the end of this contribution, the respective course of action is described.

Development of parallel benchmark code by sheet metal forming simulator 'ITAS'

International Nuclear Information System (INIS)

Watanabe, Hiroshi; Suzuki, Shintaro; Minami, Kazuo

1999-03-01

This report describes the development of parallel benchmark code by sheet metal forming simulator 'ITAS'. ITAS is a nonlinear elasto-plastic analysis program by the finite element method for the purpose of the simulation of sheet metal forming. ITAS adopts the dynamic analysis method that computes displacement of sheet metal at every time unit and utilizes the implicit method with the direct linear equation solver. Therefore the simulator is very robust. However, it requires a lot of computational time and memory capacity. In the development of the parallel benchmark code, we designed the code by MPI programming to reduce the computational time. In numerical experiments on the five kinds of parallel super computers at CCSE JAERI, i.e., SP2, SR2201, SX-4, T94 and VPP300, good performances are observed. The result will be shown to the public through WWW so that the benchmark results may become a guideline of research and development of the parallel program. (author)

Code development of total sensitivity and uncertainty analysis for reactor physics calculations

International Nuclear Information System (INIS)

Wan, C.; Cao, L.; Wu, H.; Zu, T.; Shen, W.

2015-01-01

Sensitivity and uncertainty analysis are essential parts for reactor system to perform risk and policy analysis. In this study, total sensitivity and corresponding uncertainty analysis for responses of neutronics calculations have been accomplished and developed the S&U analysis code named UNICORN. The UNICORN code can consider the implicit effects of multigroup cross sections on the responses. The UNICORN code has been applied to typical pin-cell case in this paper, and can be proved correct by comparison the results with those of the TSUNAMI-1D code. (author)

Code development of total sensitivity and uncertainty analysis for reactor physics calculations

Energy Technology Data Exchange (ETDEWEB)

Wan, C.; Cao, L.; Wu, H.; Zu, T., E-mail: chenghuiwan@stu.xjtu.edu.cn, E-mail: caolz@mail.xjtu.edu.cn, E-mail: hongchun@mail.xjtu.edu.cn, E-mail: tiejun@mail.xjtu.edu.cn [Xi' an Jiaotong Univ., School of Nuclear Science and Technology, Xi' an (China); Shen, W., E-mail: Wei.Shen@cnsc-ccsn.gc.ca [Xi' an Jiaotong Univ., School of Nuclear Science and Technology, Xi' an (China); Canadian Nuclear Safety Commission, Ottawa, ON (Canada)

2015-07-01

Sensitivity and uncertainty analysis are essential parts for reactor system to perform risk and policy analysis. In this study, total sensitivity and corresponding uncertainty analysis for responses of neutronics calculations have been accomplished and developed the S&U analysis code named UNICORN. The UNICORN code can consider the implicit effects of multigroup cross sections on the responses. The UNICORN code has been applied to typical pin-cell case in this paper, and can be proved correct by comparison the results with those of the TSUNAMI-1D code. (author)

77 FR 17460 - Multistakeholder Process To Develop Consumer Data Privacy Codes of Conduct

Science.gov (United States)

2012-03-26

..., 2012, NTIA requested public comments on (1) which consumer data privacy issues should be the focus of.... 120214135-2203-02] RIN 0660-XA27 Multistakeholder Process To Develop Consumer Data Privacy Codes of Conduct... request for public comments on the multistakeholder process to develop consumer data privacy codes of...

Development of a BWR core burn-up calculation code COREBN-BWR

International Nuclear Information System (INIS)

Morimoto, Yuichi; Okumura, Keisuke

1992-05-01

In order to evaluate core performances of BWR type reactors, the three dimensional core burnup calculation code COREBN-BWR and the fuel management code HIST-BWR have been developed. In analyses of BWR type reactors, thermal hydraulics calculations must be coupled with neutronics calculations to evaluate core performances, because steam void distribution changes according to the change of the power distribution. By installing new functions as follows to the three dimensional core burnup code COREBN2 developed in JAERI for PWR type reactor analyses, the code system becomes to be applicable to burnup analyses of BWR type reactors. (1) Macroscopic cross section calculation function taking into account of coolant void distribution. (2) Thermal hydraulics calculation function to evaluate core flow split, coolant void distribution and thermal margin. (3) Burnup calculation function under the Haling strategy. (4) Fuel management function to incorporate the thermal hydraulics information. This report consists of the general description, calculational models, input data requirements and their explanations, detailed information on usage and sample input. (author)

Basic Pilot Code Development for Two-Fluid, Three-Field Model

International Nuclear Information System (INIS)

Jeong, Jae Jun; Bae, S. W.; Lee, Y. J.; Chung, B. D.; Hwang, M.; Ha, K. S.; Kang, D. H.

2006-03-01

A basic pilot code for one-dimensional, transient, two-fluid, three-field model has been developed. Using 9 conceptual problems, the basic pilot code has been verified. The results of the verification are summarized below: - It was confirmed that the basic pilot code can simulate various flow conditions (such as single-phase liquid flow, bubbly flow, slug/churn turbulent flow, annular-mist flow, and single-phase vapor flow) and transitions of the flow conditions. A mist flow was not simulated, but it seems that the basic pilot code can simulate mist flow conditions. - The pilot code was programmed so that the source terms of the governing equations and numerical solution schemes can be easily tested. - The mass and energy conservation was confirmed for single-phase liquid and single-phase vapor flows. - It was confirmed that the inlet pressure and velocity boundary conditions work properly. - It was confirmed that, for single- and two-phase flows, the velocity and temperature of non-existing phase are calculated as intended. - During the simulation of a two-phase flow, the calculation reaches a quasisteady state with small-amplitude oscillations. The oscillations seem to be induced by some numerical causes. The research items for the improvement of the basic pilot code are listed in the last section of this report

Basic Pilot Code Development for Two-Fluid, Three-Field Model

Energy Technology Data Exchange (ETDEWEB)

Jeong, Jae Jun; Bae, S. W.; Lee, Y. J.; Chung, B. D.; Hwang, M.; Ha, K. S.; Kang, D. H

2006-03-15

A basic pilot code for one-dimensional, transient, two-fluid, three-field model has been developed. Using 9 conceptual problems, the basic pilot code has been verified. The results of the verification are summarized below: - It was confirmed that the basic pilot code can simulate various flow conditions (such as single-phase liquid flow, bubbly flow, slug/churn turbulent flow, annular-mist flow, and single-phase vapor flow) and transitions of the flow conditions. A mist flow was not simulated, but it seems that the basic pilot code can simulate mist flow conditions. - The pilot code was programmed so that the source terms of the governing equations and numerical solution schemes can be easily tested. - The mass and energy conservation was confirmed for single-phase liquid and single-phase vapor flows. - It was confirmed that the inlet pressure and velocity boundary conditions work properly. - It was confirmed that, for single- and two-phase flows, the velocity and temperature of non-existing phase are calculated as intended. - During the simulation of a two-phase flow, the calculation reaches a quasisteady state with small-amplitude oscillations. The oscillations seem to be induced by some numerical causes. The research items for the improvement of the basic pilot code are listed in the last section of this report.

Thermal-hydraulic analysis code development and application to passive safety reactor at JAERI

International Nuclear Information System (INIS)

Araya, F.

1995-01-01

After a brief overview of safety assessment process, the author describes the LOCA analysis code system developed in JAERI. It comprises audit calculation code (WREM, WREM-J2, Japanese own code and BE codes (2D/3D, ICAP, ROSA). The codes are applied to development of Japanese passive safety reactor concept JPSR. Special attention is paid to the passive heat removal system and phenomena considered to occur under loss of heat sink event. Examples of LOCA analysis based on operation of JPSR for the cases of heat removal by upper RHR and heat removal from core to atmosphere are given. Experiments for multi-dimensional flow field in RPV and steam condensation in water pool are used for understanding the phenomena in passive safety reactors. The report is in a poster form only. 1 tab., 13 figs

Development of tools for automatic generation of PLC code

CERN Document Server

Koutli, Maria; Rochez, Jacques

This Master thesis was performed at CERN and more specifically in the EN-ICE-PLC section. The Thesis describes the integration of two PLC platforms, that are based on CODESYS development tool, to the CERN defined industrial framework, UNICOS. CODESYS is a development tool for PLC programming, based on IEC 61131-3 standard, and is adopted by many PLC manufacturers. The two PLC development environments are, the SoMachine from Schneider and the TwinCAT from Beckhoff. The two CODESYS compatible PLCs, should be controlled by the SCADA system of Siemens, WinCC OA. The framework includes a library of Function Blocks (objects) for the PLC programs and a software for automatic generation of the PLC code based on this library, called UAB. The integration aimed to give a solution that is shared by both PLC platforms and was based on the PLCOpen XML scheme. The developed tools were demonstrated by creating a control application for both PLC environments and testing of the behavior of the code of the library.

Development of a Computer Code for the Estimation of Fuel Rod Failure

Energy Technology Data Exchange (ETDEWEB)

Rhee, I.H.; Ahn, H.J. [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

1997-12-31

Much research has already been performed to obtain the information on the degree of failed fuel rods from the primary coolant activities of operating PWRs in the last few decades. The computer codes that are currently in use for domestic nuclear power plants, such as CADE code and ABB-CE codes developed by Westinghouse and ABB-CE, respectively, still give significant overall errors in estimating the failed fuel rods. In addition, with the CADE code, it is difficult to predict the degree of fuel rod failures during the transient period of nuclear reactor operation, where as the ABB-CE codes are relatively more difficult to use for end-users. In particular, the rapid progresses made recently in the area of the computer hardware and software systems that their computer programs be more versatile and user-friendly. While the MS windows system that is centered on the graphic user interface and multitasking is now in widespread use, the computer codes currently employed at the nuclear power plants, such as CADE and ABB-CE codes, can only be run on the DOS system. Moreover, it is desirable to have a computer code for the fuel rod failure estimation that can directly use the radioactivity data obtained from the on-line monitoring system of the primary coolant activity. The main purpose of this study is, therefore, to develop a Windows computer code that can predict the location, the number of failed fuel rods,and the degree of failures using the radioactivity data obtained from the primary coolant activity for PWRs. Another objective is to combine this computer code with the on-line monitoring system of the primary coolant radioactivity at Kori 3 and 4 operating nuclear power plants and enable their combined use for on-line evaluation of the number and degree of fuel rod failures. (author). 49 refs., 85 figs., 30 tabs.

Development of a relativistic Particle In Cell code PARTDYN for linear accelerator beam transport

Energy Technology Data Exchange (ETDEWEB)

Phadte, D., E-mail: deepraj@rrcat.gov.in [LPD, Raja Ramanna Centre for Advanced Technology, Indore 452013 (India); Patidar, C.B.; Pal, M.K. [MAASD, Raja Ramanna Centre for Advanced Technology, Indore (India)

2017-04-11

A relativistic Particle In Cell (PIC) code PARTDYN is developed for the beam dynamics simulation of z-continuous and bunched beams. The code is implemented in MATLAB using its MEX functionality which allows both ease of development as well higher performance similar to a compiled language like C. The beam dynamics calculations carried out by the code are compared with analytical results and with other well developed codes like PARMELA and BEAMPATH. The effect of finite number of simulation particles on the emittance growth of intense beams has been studied. Corrections to the RF cavity field expressions were incorporated in the code so that the fields could be calculated correctly. The deviations of the beam dynamics results between PARTDYN and BEAMPATH for a cavity driven in zero-mode have been discussed. The beam dynamics studies of the Low Energy Beam Transport (LEBT) using PARTDYN have been presented.

Development of a graphical interface computer code for reactor fuel reloading optimization

International Nuclear Information System (INIS)

Do Quang Binh; Nguyen Phuoc Lan; Bui Xuan Huy

2007-01-01

This report represents the results of the project performed in 2007. The aim of this project is to develop a graphical interface computer code that allows refueling engineers to design fuel reloading patterns for research reactor using simulated graphical model of reactor core. Besides, this code can perform refueling optimization calculations based on genetic algorithms as well as simulated annealing. The computer code was verified based on a sample problem, which relies on operational and experimental data of Dalat research reactor. This code can play a significant role in in-core fuel management practice at nuclear research reactor centers and in training. (author)

Development and application of sub-channel analysis code based on SCWR core

International Nuclear Information System (INIS)

Fu Shengwei; Xu Zhihong; Yang Yanhua

2011-01-01

The sub-channel analysis code SABER was developed for thermal-hydraulic analysis of supercritical water-cooled reactor (SCWR) fuel assembly. The extended computational cell structure, a new boundary conditions, 3 dimensional heat conduction model and water properties package were implemented in SABER code, which could be used to simulate the thermal fuel assembly of SCWR. To evaluate the applicability of the code, a steady state calculation of the fuel assembly was performed. The results indicate good applicability of the SABER code to simulate the counter-current flow and the heat exchange between coolant and moderator channels. (authors)

Development of standards, codes of practice and guidelines at the national level

International Nuclear Information System (INIS)

Swindon, T.N.

1989-01-01

Standards, codes of practice and guidelines are defined and their different roles in radiation protection specified. The work of the major bodies that develop such documents in Australia - the National Health and Medical Research Council and the Standards Association of Australia - is discussed. The codes of practice prepared under the Environment Protection (Nuclear Codes) Act, 1978, an act of the Australian Federal Parliament, are described and the guidelines associated with them outlined. 5 refs

Development of system analysis code for pyrochemical process using molten salt electrorefining

International Nuclear Information System (INIS)

Tozawa, K.; Matsumoto, T.; Kakehi, I.

2000-04-01

This report describes accomplishment of development of a cathode processor calculation code to simulate the mass and heat transfer phenomena with the distillation process and development of an analytical model for cooling behavior of the pyrochemical process cell on personal computers. The pyrochemical process using molten salt electrorefining would introduce new technologies for new fuels of particle oxide, particle nitride and metallic fuels. The cathode processor calculation code with distillation process was developed. A code validation calculation has been conducted on the basic of the benchmark problem for natural convection in a square cavity. Results by using the present code agreed well for the velocity-temperature fields, the maximum velocity and its location with the benchmark solution published in a paper. The functions have been added to advance the reality in simulation and to increase the efficiency in utilization. The test run has been conducted using the code with the above modification for an axisymmetric enclosed vessel simulating a cathode processor, and the capability of the distillation process simulation with the code has been confirmed. An analytical model for cooling behavior of the pyrochemical process cell was developed. The analytical model was selected by comparing benchmark analysis with detailed analysis on engineering workstation. Flow and temperature distributions were confirmed by the result of steady state analysis. In the result of transient cooling analysis, an initial transient peak of temperature occurred at balanced heat condition in the steady-state analysis. Final gas temperature distribution was dependent on gas circulation flow in transient condition. Then there were different final gas temperature distributions on the basis of the result of steady-state analysis. This phenomenon has a potential for it's own metastable condition. Therefore it was necessary to design gas cooling flow pattern without cooling gas circulation

Development and validation of GWHEAD, a three-dimensional groundwater head computer code

International Nuclear Information System (INIS)

Beckmeyer, R.R.; Root, R.W.; Routt, K.R.

1980-03-01

A computer code has been developed to solve the groundwater flow equation in three dimensions. The code has finite-difference approximations solved by the strongly implicit solution procedure. Input parameters to the code include hydraulic conductivity, specific storage, porosity, accretion (recharge), and initial hydralic head. These parameters may be input as varying spatially. The hydraulic conductivity may be input as isotropic or anisotropic. The boundaries either may permit flow across them or may be impermeable. The code has been used to model leaky confined groundwater conditions and spherical flow to a continuous point sink, both of which have exact analytical solutions. The results generated by the computer code compare well with those of the analytical solutions. The code was designed to be used to model groundwater flow beneath fuel reprocessing and waste storage areas at the Savannah River Plant

TOOKUIL: A case study in user interface development for safety code application

International Nuclear Information System (INIS)

Gray, D.L.; Harkins, C.K.; Hoole, J.G.

1997-01-01

Traditionally, there has been a very high learning curve associated with using nuclear power plant (NPP) analysis codes. Even for seasoned plant analysts and engineers, the process of building or modifying an input model for present day NPP analysis codes is tedious, error prone, and time consuming. Current cost constraints and performance demands place an additional burden on today's safety analysis community. Advances in graphical user interface (GUI) technology have been applied to obtain significant productivity and quality assurance improvements for the Transient Reactor Analysis Code (TRAC) input model development. KAPL Inc. has developed an X Windows-based graphical user interface named TOOKUIL which supports the design and analysis process, acting as a preprocessor, runtime editor, help system, and post processor for TRAC. This paper summarizes the objectives of the project, the GUI development process and experiences, and the resulting end product, TOOKUIL

TOOKUIL: A case study in user interface development for safety code application

International Nuclear Information System (INIS)

Gray, D.L.; Harkins, C.K.; Hoole, J.G.; Peebles, R.C.; Smith, R.J.

1996-11-01

Traditionally, there has been a very high learning curve associated with using nuclear power plant (NPP) analysis codes. Even for seasoned plant analysts and engineers, the process of building or modifying an input model for present day NPP analysis codes is tedious, error prone, and time consuming. Current cost constraints and performance demands place an additional burden on today's safety analysis community. Advances in graphical user interface (GUI) technology have been applied to obtain significant productivity and quality assurance improvements for the Transient Reactor Analysis Code (TRAC) input model development. KAPL Inc. has developed an X Windows-based graphical user interface named TOOKUIL which supports the design and analysis process, acting as a preprocessor, runtime editor, help system, and post processor for TRAC. This paper summarizes the objectives of the project, the GUI development process and experiences, and the resulting end product, TOOKUIL

Benchmark Simulation for the Development of the Regulatory Audit Subchannel Analysis Code

Energy Technology Data Exchange (ETDEWEB)

Lee, G. H.; Song, C.; Woo, S. W. [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2012-05-15

For the safe and reliable operation of a reactor, it is important to predict accurately the flow and temperature distributions in the thermal-hydraulic design of a reactor core. A subchannel approach can give the reasonable flow and temperature distributions with the short computing time. Korea Institute of Nuclear Safety (KINS) is presently reviewing new subchannel code, THALES, which will substitute for both THINC-IV and TORC code. To assess the prediction performance of THALES, KINS is developing the subchannel analysis code for the independent audit calculation. The code is based on workstation version of COBRA-IV-I. The main objective of the present study is to assess the performance of COBRA-IV-I code by comparing the simulation results with experimental ones for the sample problems

Development of a national code of practice for structural masonry ...

African Journals Online (AJOL)

The problems and constraints faced by most developing countries, particularly Ghana, in developing codes of practice for structural masonry are highlighted. The steps that must be undertaken through the coordinated efforts of the National Standards Boards, Research Institutions, Universities and Professional Bodies in the ...

Development and Implementation of CFD-Informed Models for the Advanced Subchannel Code CTF

Science.gov (United States)

Blyth, Taylor S.

The research described in this PhD thesis contributes to the development of efficient methods for utilization of high-fidelity models and codes to inform low-fidelity models and codes in the area of nuclear reactor core thermal-hydraulics. The objective is to increase the accuracy of predictions of quantities of interests using high-fidelity CFD models while preserving the efficiency of low-fidelity subchannel core calculations. An original methodology named Physics-based Approach for High-to-Low Model Information has been further developed and tested. The overall physical phenomena and corresponding localized effects, which are introduced by the presence of spacer grids in light water reactor (LWR) cores, are dissected in corresponding four building basic processes, and corresponding models are informed using high-fidelity CFD codes. These models are a spacer grid-directed cross-flow model, a grid-enhanced turbulent mixing model, a heat transfer enhancement model, and a spacer grid pressure loss model. The localized CFD-models are developed and tested using the CFD code STAR-CCM+, and the corresponding global model development and testing in sub-channel formulation is performed in the thermal-hydraulic subchannel code CTF. The improved CTF simulations utilize data-files derived from CFD STAR-CCM+ simulation results covering the spacer grid design desired for inclusion in the CTF calculation. The current implementation of these models is examined and possibilities for improvement and further development are suggested. The validation experimental database is extended by including the OECD/NRC PSBT benchmark data. The outcome is an enhanced accuracy of CTF predictions while preserving the computational efficiency of a low-fidelity subchannel code.

Development and Implementation of CFD-Informed Models for the Advanced Subchannel Code CTF

Energy Technology Data Exchange (ETDEWEB)

Blyth, Taylor S. [Pennsylvania State Univ., University Park, PA (United States); Avramova, Maria [North Carolina State Univ., Raleigh, NC (United States)

2017-04-01

The research described in this PhD thesis contributes to the development of efficient methods for utilization of high-fidelity models and codes to inform low-fidelity models and codes in the area of nuclear reactor core thermal-hydraulics. The objective is to increase the accuracy of predictions of quantities of interests using high-fidelity CFD models while preserving the efficiency of low-fidelity subchannel core calculations. An original methodology named Physics- based Approach for High-to-Low Model Information has been further developed and tested. The overall physical phenomena and corresponding localized effects, which are introduced by the presence of spacer grids in light water reactor (LWR) cores, are dissected in corresponding four building basic processes, and corresponding models are informed using high-fidelity CFD codes. These models are a spacer grid-directed cross-flow model, a grid-enhanced turbulent mixing model, a heat transfer enhancement model, and a spacer grid pressure loss model. The localized CFD-models are developed and tested using the CFD code STAR-CCM+, and the corresponding global model development and testing in sub-channel formulation is performed in the thermal- hydraulic subchannel code CTF. The improved CTF simulations utilize data-files derived from CFD STAR-CCM+ simulation results covering the spacer grid design desired for inclusion in the CTF calculation. The current implementation of these models is examined and possibilities for improvement and further development are suggested. The validation experimental database is extended by including the OECD/NRC PSBT benchmark data. The outcome is an enhanced accuracy of CTF predictions while preserving the computational efficiency of a low-fidelity subchannel code.

System transient analysis code development for low pressure and low power

International Nuclear Information System (INIS)

Kim, Hee Cheol

1998-02-01

A real time reactor system analysis code, ARTIST, based on drift flux model has been developed to investigate the transient system behavior under low pressure, low flow and low power conditions with noncondensable gas present in the system. The governing equations of the ARTIST code consist of three mass continuity equations (steam, liquid and noncondensable), two energy equations (gas and mixture) and one momentum equation (mixture) constituted with the drift flux model. The capability of ARTIST in predicting two-phase flow void distribution in the system has been validated against experimental data. The results of the ARTIST axial void distribution at low pressure and low flow, are far better than the results of both the homogeneous model of TASS code and the two-fluid model of RELAP5/MOD3 code. Also, RELAP5/MOD3 calculation shows the large amplitude of void fraction oscillations at low pressure. These results imply that interfacial momentum transfer terms in the two-fluid model formulation should be carefully constituted, especially for the low pressure condition due to the big density differences between steam and water. Thermal-hydraulic state solution scheme is developed when noncondensable gas exists. Numerical consistency and convergence of obtaining equilibrium state is tested with the ideal problems for various situations including very low partial pressure conditions. Calculated thermal-hydraulic state for each test shows consistent and expected behaviour. A new multi-layer back propagation network algorithm for calculating the departure from nucleate boiling ratio (DNBR) is developed and adopted in ARTIST code in order to have real-time DNBR evaluation by eliminating the tandem procedure of the transient DNBR calculation. The algorithm trained by different patterns generated by latin hypercube sampling method on the performance space is tested for the randomly sampled untrained data and the transient DNBR data. The uncertainty of the algorithm is

Development of a subchannel analysis code MATRA (Ver. α)

International Nuclear Information System (INIS)

Yoo, Y. J.; Hwang, D. H.

1998-04-01

A subchannel analysis code MATRA-α, an interim version of MATRA, has been developed to be run on an IBM PC or HP WS based on the existing CDC CYBER mainframe version of COBRA-IV-I. This MATRA code is a thermal-hydraulic analysis code based on the subchannel approach for calculating the enthalpy and flow distribution in fuel assemblies and reactor cores for both steady-state and transient conditions. MATRA-α has been provided with an improved structure, various functions, and models to give the more convenient user environment and to increase the code accuracy, various functions, and models to give the more convenient user environment and to increase the code accuracy. Among them, the pressure drop model has been improved to be applied to non-square-lattice rod arrays, and the lateral transport models between adjacent subchannels have been improved to increase the accuracy in predicting two-phase flow phenomena. Also included in this report are the detailed instructions for input data preparation and for auxiliary pre-processors to serve as a guide to those who want to use MATRA-α. In addition, we compared the predictions of MATRA-α with the experimental data on the flow and enthalpy distribution in three sample rod-bundle cases to evaluate the performance of MATRA-α. All the results revealed that the prediction of MATRA-α were better than those of COBRA-IV-I. (author). 16 refs., 1 tab., 13 figs

Constitutive model development needs for reactor safety thermal-hydraulic codes

International Nuclear Information System (INIS)

Kelly, J.M.

1998-01-01

This paper discusses the constitutive model development needs for our current and future generation of reactor safety thermal-hydraulic analysis codes. Rather than provide a simple 'shopping list' of models to be improved, a detailed description is given of how a constitutive model works within the computational framework of a current reactor safety code employing the two-fluid model of two-phase flow. The intent is to promote a better understanding of both the types of experiments and the instrumentation needs that will be required in the USNRCs code improvement program. First, a summary is given of the modeling considerations that need to be taken into account when developing constitutive models for use in reactor safety thermal-hydraulic codes. Specifically, the two-phase flow model should be applicable to a control volume formulation employing computational volumes with dimensions on the order of meters but containing embedded structure with a dimension on the order of a centimeter. The closure relations are then required to be suitable when averaged over such large volumes containing millions or even tens of millions of discrete fluid particles (bubbles/drops). This implies a space and time averaging procedure that neglects the intermittency observed in slug and chum turbulent two-phase flows. Furthermore, the geometries encountered in reactor systems are complex, the constitutive relations should therefore be component specific (e.g., interfacial shear in a tube does not represent that in a rod bundle nor in the downcomer). When practicable, future modeling efforts should be directed towards resolving the spatial evolution of two-phase flow patterns through the introduction of interfacial area transport equations and by modeling the individual physical processes responsible for the creation or destruction of interfacial area. Then the example of the implementation and assessment of a subcooled boiling model in a two-fluid code is given. The primary parameter

Development of a 3D non-linear implicit MHD code

International Nuclear Information System (INIS)

Nicolas, T.; Ichiguchi, K.

2016-06-01

This paper details the on-going development of a 3D non-linear implicit MHD code, which aims at making possible large scale simulations of the non-linear phase of the interchange mode. The goal of the paper is to explain the rationale behind the choices made along the development, and the technical difficulties encountered. At the present stage, the development of the code has not been completed yet. Most of the discussion is concerned with the first approach, which utilizes cartesian coordinates in the poloidal plane. This approach shows serious difficulties in writing the preconditioner, closely related to the choice of coordinates. A second approach, based on curvilinear coordinates, also faced significant difficulties, which are detailed. The third and last approach explored involves unstructured tetrahedral grids, and indicates the possibility to solve the problem. The issue to domain meshing is addressed. (author)

Development of Teaching Materials for a Physical Chemistry Experiment Using the QR Code

OpenAIRE

吉村, 忠与志

2008-01-01

The development of teaching materials with the QR code was attempted in an educational environment using a mobile telephone. The QR code is not sufficiently utilized in education, and the current study is one of the first in the field. The QR code is encrypted. However, the QR code can be deciphered by mobile telephones, thus enabling the expression of text in a small space.Contents of "Physical Chemistry Experiment" which are available on the Internet are briefly summarized and simplified. T...

Analyses and computer code developments for accident-induced thermohydraulic transients in water-cooled nuclear reactor systems

International Nuclear Information System (INIS)

Wulff, W.

1977-01-01

A review is presented on the development of analyses and computer codes for the prediction of thermohydraulic transients in nuclear reactor systems. Models for the dynamics of two-phase mixtures are summarized. Principles of process, reactor component and reactor system modeling are presented, as well as the verification of these models by comparing predicted results with experimental data. Codes of major importance are described, which have recently been developed or are presently under development. The characteristics of these codes are presented in terms of governing equations, solution techniques and code structure. Current efforts and problems of code verification are discussed. A summary is presented of advances which are necessary for reducing the conservatism currently implied in reactor hydraulics codes for safety assessment

Development of the CAT code - YGN 5 and 6 CVCS analysis tool

International Nuclear Information System (INIS)

Kim, S.W.; Sohn, S.H.; Seo, J.T.; Lee, S.K.

1996-01-01

The CAT code has been developed for the analysis of the Chemical and Volume Control System (CVCS) of the Yonggwang Nuclear Power Plant Units 5 and 6(YGN 5 and 6). The code is able to simulate the system behaviors in the operating conditions which should be considered in the design of the system. It has been developed as a stand alone code which can simulate CVCS in detail whenever correct system boundary conditions are provided. The code consists of two modules, i.e. control and process modules. The control module includes the models for the Pressurizer Level Control System, the Letdown Backpressure Control System, the Charging Backpressure Control System, and the Seal Injection Control System. Thermal-hydraulic responses of the system are simulated by the process module. The modeling of the system is based on a node and flowpath network. The thermal-hydraulic model is based on the assumption of homogeneous equilibrium mixture. The major system components such as valves, orifices, pumps, heat exchangers and the volume control tank are explicitly modeled in the code. The code was validated against the measured data from the letdown system test performed during the Hot Functional Testing at YGN 3. The comparison between the measured and predicted data demonstrated that the present model can predict the observed phenomena with sufficient accuracy. (author)

Nuclear Energy Advanced Modeling and Simulation (NEAMS) waste Integrated Performance and Safety Codes (IPSC): gap analysis for high fidelity and performance assessment code development

International Nuclear Information System (INIS)

Lee, Joon H.; Siegel, Malcolm Dean; Arguello, Jose Guadalupe Jr.; Webb, Stephen Walter; Dewers, Thomas A.; Mariner, Paul E.; Edwards, Harold Carter; Fuller, Timothy J.; Freeze, Geoffrey A.; Jove-Colon, Carlos F.; Wang, Yifeng

2011-01-01

This report describes a gap analysis performed in the process of developing the Waste Integrated Performance and Safety Codes (IPSC) in support of the U.S. Department of Energy (DOE) Office of Nuclear Energy Advanced Modeling and Simulation (NEAMS) Campaign. The goal of the Waste IPSC is to develop an integrated suite of computational modeling and simulation capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive waste storage or disposal system. The Waste IPSC will provide this simulation capability (1) for a range of disposal concepts, waste form types, engineered repository designs, and geologic settings, (2) for a range of time scales and distances, (3) with appropriate consideration of the inherent uncertainties, and (4) in accordance with rigorous verification, validation, and software quality requirements. The gap analyses documented in this report were are performed during an initial gap analysis to identify candidate codes and tools to support the development and integration of the Waste IPSC, and during follow-on activities that delved into more detailed assessments of the various codes that were acquired, studied, and tested. The current Waste IPSC strategy is to acquire and integrate the necessary Waste IPSC capabilities wherever feasible, and develop only those capabilities that cannot be acquired or suitably integrated, verified, or validated. The gap analysis indicates that significant capabilities may already exist in the existing THC codes although there is no single code able to fully account for all physical and chemical processes involved in a waste disposal system. Large gaps exist in modeling chemical processes and their couplings with other processes. The coupling of chemical processes with flow transport and mechanical deformation remains challenging. The data for extreme environments (e.g., for elevated temperature and high ionic strength media) that are

Nuclear Energy Advanced Modeling and Simulation (NEAMS) waste Integrated Performance and Safety Codes (IPSC) : gap analysis for high fidelity and performance assessment code development.

Energy Technology Data Exchange (ETDEWEB)

Lee, Joon H.; Siegel, Malcolm Dean; Arguello, Jose Guadalupe, Jr.; Webb, Stephen Walter; Dewers, Thomas A.; Mariner, Paul E.; Edwards, Harold Carter; Fuller, Timothy J.; Freeze, Geoffrey A.; Jove-Colon, Carlos F.; Wang, Yifeng

2011-03-01

This report describes a gap analysis performed in the process of developing the Waste Integrated Performance and Safety Codes (IPSC) in support of the U.S. Department of Energy (DOE) Office of Nuclear Energy Advanced Modeling and Simulation (NEAMS) Campaign. The goal of the Waste IPSC is to develop an integrated suite of computational modeling and simulation capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive waste storage or disposal system. The Waste IPSC will provide this simulation capability (1) for a range of disposal concepts, waste form types, engineered repository designs, and geologic settings, (2) for a range of time scales and distances, (3) with appropriate consideration of the inherent uncertainties, and (4) in accordance with rigorous verification, validation, and software quality requirements. The gap analyses documented in this report were are performed during an initial gap analysis to identify candidate codes and tools to support the development and integration of the Waste IPSC, and during follow-on activities that delved into more detailed assessments of the various codes that were acquired, studied, and tested. The current Waste IPSC strategy is to acquire and integrate the necessary Waste IPSC capabilities wherever feasible, and develop only those capabilities that cannot be acquired or suitably integrated, verified, or validated. The gap analysis indicates that significant capabilities may already exist in the existing THC codes although there is no single code able to fully account for all physical and chemical processes involved in a waste disposal system. Large gaps exist in modeling chemical processes and their couplings with other processes. The coupling of chemical processes with flow transport and mechanical deformation remains challenging. The data for extreme environments (e.g., for elevated temperature and high ionic strength media) that are

Development of computer code models for analysis of subassembly voiding in the LMFBR

International Nuclear Information System (INIS)

Hinkle, W.

1979-12-01

The research program discussed in this report was started in FY1979 under the combined sponsorship of the US Department of Energy (DOE), General Electric (GE) and Hanford Engineering Development Laboratory (HEDL). The objective of the program is to develop multi-dimensional computer codes which can be used for the analysis of subassembly voiding incoherence under postulated accident conditions in the LMFBR. Two codes are being developed in parallel. The first will use a two fluid (6 equation) model which is more difficult to develop but has the potential for providing a code with the utmost in flexibility and physical consistency for use in the long term. The other will use a mixture (< 6 equation) model which is less general but may be more amenable to interpretation and use of experimental data and therefore, easier to develop for use in the near term. To assure that the models developed are not design dependent, geometries and transient conditions typical of both foreign and US designs are being considered

TOOKUIL: A case study in user interface development for safety code application

Energy Technology Data Exchange (ETDEWEB)

Gray, D.L.; Harkins, C.K.; Hoole, J.G. [and others

1997-07-01

Traditionally, there has been a very high learning curve associated with using nuclear power plant (NPP) analysis codes. Even for seasoned plant analysts and engineers, the process of building or modifying an input model for present day NPP analysis codes is tedious, error prone, and time consuming. Current cost constraints and performance demands place an additional burden on today`s safety analysis community. Advances in graphical user interface (GUI) technology have been applied to obtain significant productivity and quality assurance improvements for the Transient Reactor Analysis Code (TRAC) input model development. KAPL Inc. has developed an X Windows-based graphical user interface named TOOKUIL which supports the design and analysis process, acting as a preprocessor, runtime editor, help system, and post processor for TRAC. This paper summarizes the objectives of the project, the GUI development process and experiences, and the resulting end product, TOOKUIL.

Long non-coding RNA expression profiling of mouse testis during postnatal development.

Directory of Open Access Journals (Sweden)

Jin Sun

Full Text Available Mammalian testis development and spermatogenesis play critical roles in male fertility and continuation of a species. Previous research into the molecular mechanisms of testis development and spermatogenesis has largely focused on the role of protein-coding genes and small non-coding RNAs, such as microRNAs and piRNAs. Recently, it has become apparent that large numbers of long (>200 nt non-coding RNAs (lncRNAs are transcribed from mammalian genomes and that lncRNAs perform important regulatory functions in various developmental processes. However, the expression of lncRNAs and their biological functions in post-natal testis development remain unknown. In this study, we employed microarray technology to examine lncRNA expression profiles of neonatal (6-day-old and adult (8-week-old mouse testes. We found that 8,265 lncRNAs were expressed above background levels during post-natal testis development, of which 3,025 were differentially expressed. Candidate lncRNAs were identified for further characterization by an integrated examination of genomic context, gene ontology (GO enrichment of their associated protein-coding genes, promoter analysis for epigenetic modification, and evolutionary conservation of elements. Many lncRNAs overlapped or were adjacent to key transcription factors and other genes involved in spermatogenesis, such as Ovol1, Ovol2, Lhx1, Sox3, Sox9, Plzf, c-Kit, Wt1, Sycp2, Prm1 and Prm2. Most differentially expressed lncRNAs exhibited epigenetic modification marks similar to protein-coding genes and tend to be expressed in a tissue-specific manner. In addition, the majority of differentially expressed lncRNAs harbored evolutionary conserved elements. Taken together, our findings represent the first systematic investigation of lncRNA expression in the mammalian testis and provide a solid foundation for further research into the molecular mechanisms of lncRNAs function in mammalian testis development and spermatogenesis.

Development of a code for description of sodium spray and pool fires. Pt. 1

International Nuclear Information System (INIS)

Alexas, A.

1979-09-01

In the scope of the development of a code to describe both, sodium pool- and spray fires, the well-known codes SOFIRE II and NABRAND have been compared. Regarding the program technique of both codes, the NABRAND-code seems to be the better one, though it includes some conservatisms in the modelling and in the transport coefficients used. For a realistic estimation of the consequences of large sodium fires in an LMFBR, an elimination of these conservatisms is necessary. After that it must be investigated if a combination of the modificated version of the NABRAND-code and of a spray fire-code (for example the code SPRAY) is efficient. (orig.) [de

Highly conserved non-coding sequences are associated with vertebrate development.

Directory of Open Access Journals (Sweden)

Adam Woolfe

2005-01-01

Full Text Available In addition to protein coding sequence, the human genome contains a significant amount of regulatory DNA, the identification of which is proving somewhat recalcitrant to both in silico and functional methods. An approach that has been used with some success is comparative sequence analysis, whereby equivalent genomic regions from different organisms are compared in order to identify both similarities and differences. In general, similarities in sequence between highly divergent organisms imply functional constraint. We have used a whole-genome comparison between humans and the pufferfish, Fugu rubripes, to identify nearly 1,400 highly conserved non-coding sequences. Given the evolutionary divergence between these species, it is likely that these sequences are found in, and furthermore are essential to, all vertebrates. Most, and possibly all, of these sequences are located in and around genes that act as developmental regulators. Some of these sequences are over 90% identical across more than 500 bases, being more highly conserved than coding sequence between these two species. Despite this, we cannot find any similar sequences in invertebrate genomes. In order to begin to functionally test this set of sequences, we have used a rapid in vivo assay system using zebrafish embryos that allows tissue-specific enhancer activity to be identified. Functional data is presented for highly conserved non-coding sequences associated with four unrelated developmental regulators (SOX21, PAX6, HLXB9, and SHH, in order to demonstrate the suitability of this screen to a wide range of genes and expression patterns. Of 25 sequence elements tested around these four genes, 23 show significant enhancer activity in one or more tissues. We have identified a set of non-coding sequences that are highly conserved throughout vertebrates. They are found in clusters across the human genome, principally around genes that are implicated in the regulation of development

Development of a system of computer codes for severe accident analyses and its applications

Energy Technology Data Exchange (ETDEWEB)

Chang, Soon Hong; Cheon, Moon Heon; Cho, Nam jin; No, Hui Cheon; Chang, Hyeon Seop; Moon, Sang Kee; Park, Seok Jeong; Chung, Jee Hwan [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

1991-12-15

The objectives of this study is to develop a system of computer codes for postulated severe accident analyses in Nuclear Power Plants. This system of codes is necessary to conduct individual plant examination for domestic nuclear power plants. As a result of this study, one can conduct severe accident assessments more easily, and can extract the plant-specific vulnerabilities for severe accidents and at the same time the ideas for enhancing overall accident resistance. The scope and contents of this study are as follows : development of a system of computer codes for severe accident analyses, development of severe accident management strategy.

Development of a system of computer codes for severe accident analyses and its applications

International Nuclear Information System (INIS)

Chang, Soon Hong; Cheon, Moon Heon; Cho, Nam jin; No, Hui Cheon; Chang, Hyeon Seop; Moon, Sang Kee; Park, Seok Jeong; Chung, Jee Hwan

1991-12-01

The objectives of this study is to develop a system of computer codes for postulated severe accident analyses in Nuclear Power Plants. This system of codes is necessary to conduct individual plant examination for domestic nuclear power plants. As a result of this study, one can conduct severe accident assessments more easily, and can extract the plant-specific vulnerabilities for severe accidents and at the same time the ideas for enhancing overall accident resistance. The scope and contents of this study are as follows : development of a system of computer codes for severe accident analyses, development of severe accident management strategy

Strategies for developing subchannel capability in an advanced system thermalhydraulic code: a literature review

International Nuclear Information System (INIS)

Cheng, J.; Rao, Y.F.

2015-01-01

In the framework of developing next generation safety analysis tools, Canadian Nuclear Laboratories (CNL) has planned to incorporate subchannel analysis capability into its advanced system thermalhydraulic code CATHENA 4. This paper provides a literature review and an assessment of current subchannel codes. It also evaluates three code-development methods: (i) static coupling of CATHENA 4 with the subchannel code ASSERT-PV, (ii) dynamic coupling of the two codes, and (iii) fully implicit implementation for a new, standalone CATHENA 4 version with subchannel capability. Results of the review and assessment suggest that the current ASSERT-PV modules can be used as the base for the fully implicit implementation of subchannel capability in CATHENA 4, and that this option may be the most cost-effective in the long run, resulting in savings in user application and maintenance costs. In addition, improved versatility of the tool could be accomplished by the addition of new features that could be added as part of its development. The new features would improve the capabilities of the existing subchannel code in handling low, reverse, and stagnant flows often encountered in system thermalhydraulic analysis. Therefore, the method of fully implicit implementation is preliminarily recommended for further exploration. A feasibility study will be performed in an attempt to extend the present work into a preliminary development plan. (author)

Trends in EFL Technology and Educational Coding: A Case Study of an Evaluation Application Developed on LiveCode

Science.gov (United States)

Uehara, Suwako; Noriega, Edgar Josafat Martinez

2016-01-01

The availability of user-friendly coding software is increasing, yet teachers might hesitate to use this technology to develop for educational needs. This paper discusses studies related to technology for educational uses and introduces an evaluation application being developed. Through questionnaires by student users and open-ended discussion by…

A development and an application of Mixset-X computer code for simulating the Purex solvent extraction system

International Nuclear Information System (INIS)

Shida, M.; Naito, M.; Suto, T.; Omori, E.; Nojiri, T.

2001-01-01

MIXSET is a FORTRAN code developed to simulate the Purex solvent extraction system using mixer-settler extractors. Japan Nuclear Cycle Development Institute (JNC) has been developing the MIXSET code since the years 1970 to analyze the behavior of nuclides in the solvent extraction processes in Tokai Reprocessing Plant (TRP). This paper describes the history of MIXSET code development, the features of the latest version, called MIXSET-X and the application of the code for safety evaluation work. (author)

Development and improvement of safety analysis code for geological disposal

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

In order to confirm the long-term safety concerning geological disposal, probabilistic safety assessment code and other analysis codes, which can evaluate possibility of each event and influence on engineered barrier and natural barrier by the event, were introduced. We confirmed basic functions of those codes and studied the relation between those functions and FEP/PID which should be taken into consideration in safety assessment. We are planning to develop 'Nuclide Migration Assessment System' for the purpose of realizing improvement in efficiency of assessment work, human error prevention for analysis, and quality assurance of the analysis environment and analysis work for safety assessment by using it. As the first step, we defined the system requirements and decided the system composition and functions which should be mounted in them based on those requirements. (author)

Development of simplified decommissioning cost estimation code for nuclear facilities

International Nuclear Information System (INIS)

Tachibana, Mitsuo; Shiraishi, Kunio; Ishigami, Tsutomu

2010-01-01

The simplified decommissioning cost estimation code for nuclear facilities (DECOST code) was developed in consideration of features and structures of nuclear facilities and similarity of dismantling methods. The DECOST code could calculate 8 evaluation items of decommissioning cost. Actual dismantling in the Japan Atomic Energy Agency (JAEA) was evaluated; unit conversion factors used to calculate the manpower of dismantling activities were evaluated. Consequently, unit conversion factors of general components could be classified into three kinds. Weights of components and structures of the facility were necessary for calculation of manpower. Methods for evaluating weights of components and structures of the facility were studied. Consequently, the weight of components in the facility was proportional to the weight of structures of the facility. The weight of structures of the facility was proportional to the total area of floors in the facility. Decommissioning costs of 7 nuclear facilities in the JAEA were calculated by using the DECOST code. To verify the calculated results, the calculated manpower was compared with the manpower gained from actual dismantling. Consequently, the calculated manpower and actual manpower were almost equal. The outline of the DECOST code, evaluation results of unit conversion factors, the evaluation method of the weights of components and structures of the facility are described in this report. (author)

Development Status of Diffusion Code RAST-K 2.0 at UNIST

Energy Technology Data Exchange (ETDEWEB)

Park, Minyong; Zheng, Youqi; Choe, Jiwon; Zhang, Peng; Lee, Deokjung [UNIST, Ulsan (Korea, Republic of); Lee, Eunki; Shin, Hocheol [KHNP Central Research Institute, Daejeon (Korea, Republic of)

2016-10-15

The non-linear scheme was used based on the 2-group CMFD and a three dimensional multi -group unified nodal method (UNM). To consider the history effects, the main heavy isotopes were tracked by micro-depletion module using CRAM. The simplified 1-D single channel thermal hydraulic solver from nTACER is implemented. The θ method was adopted in the transient calculation. To get detailed pin-wise power and burnup distribution, Pin power reconstruction module was implemented. Also automatic control logic to calculate MTC, FTC, control rod worth was implemented. To perform multicycle analysis, restart and shuffling/rotation module has been implemented. To link between CASMO-4E and RAST-K 2.0, CATORA (CASMO TO RAST-K 2.0) code was developed. Unlike the other diffusion codes, RAST-K 2.0 depletion module uses CRAM and extended depletion chain for fission products. Most lattice codes give cumulative fission yield of Pm-149 without considering Pm-148 and Pm-149 capture reaction which will lead to the increase of Sm-149 number density. This paper reports the status of RAST-K 2.0 code development at UNIST. The new code applies a new kernel based on the two-node UNM with CMFD, and θ method for kinetic calculation. Also, the microdepletion calculation is used to consider the history effects. And other modules and functions also implemented such as pin power reconstruction, branch calculation, restart, multi-cycle, and 1-D single channel T/H solver.

Recent developments of JAEA’s Monte Carlo code MVP for reactor physics applications

International Nuclear Information System (INIS)

Nagaya, Yasunobu; Okumura, Keisuke; Mori, Takamasa

2015-01-01

Highlights: • This paper describes the recent development status of the Monte Carlo code MVP. • The basic features and capabilities of MVP are briefly described. • New capabilities useful for reactor analysis are also described. - Abstract: This paper describes the recent development status of a Monte Carlo code MVP developed at Japan Atomic Energy Agency. The basic features and capabilities of MVP are overviewed. In addition, new capabilities useful for reactor analysis are also described

Development of the computer code system for the analyses of PWR core

International Nuclear Information System (INIS)

Tsujimoto, Iwao; Naito, Yoshitaka.

1992-11-01

This report is one of the materials for the work titled 'Development of the computer code system for the analyses of PWR core phenomena', which is performed under contracts between Shikoku Electric Power Company and JAERI. In this report, the numerical method adopted in our computer code system are described, that is, 'The basic course and the summary of the analysing method', 'Numerical method for solving the Boltzmann equation', 'Numerical method for solving the thermo-hydraulic equations' and 'Description on the computer code system'. (author)

Development of a tracer transport option for the NAPSAC fracture network computer code

International Nuclear Information System (INIS)

Herbert, A.W.

1990-06-01

The Napsac computer code predicts groundwater flow through fractured rock using a direct fracture network approach. This paper describes the development of a tracer transport algorithm for the NAPSAC code. A very efficient particle-following approach is used enabling tracer transport to be predicted through large fracture networks. The new algorithm is tested against three test examples. These demonstrations confirm the accuracy of the code for simple networks, where there is an analytical solution to the transport problem, and illustrates the use of the computer code on a more realistic problem. (author)

Development and verifications of fast reactor fuel design code ''Ceptar''

International Nuclear Information System (INIS)

Ozawa, T.; Nakazawa, H.; Abe, T.

2001-01-01

The annular fuel is very beneficial for fast reactors, because it is available for both high power and high burn-up. Concerning the irradiation behavior of the annular fuel, most of annular pellets irradiated up to high burn-up showed shrinkage of the central hole due to deformation and restructuring of the pellets. It is needed to predict precisely the shrinkage of the central hole during irradiation, because it has a great influence on power-to-melt. In this paper, outline of CEPTAR code (Calculation code to Evaluate fuel pin stability for annular fuel design) developed to meet this need is presented. In this code, the radial profile of fuel density can be computed by using the void migration model, and law of conservation of mass defines the inner diameter. For the mechanical analysis, the fuel and cladding deformation caused by the thermal expansion, swelling and creep is computed by the stress-strain analysis using the approximation of plane-strain. In addition, CEPTAR can also take into account the effect of Joint-Oxide-Gain (JOG) which is observed in fuel-cladding gap of high burn-up fuel. JOG has an effect to decrease the fuel swelling and to improve the gap conductance due to deposition of solid fission product. Based on post-irradiation data on PFR annular fuel, we developed an empirical model for JOG. For code verifications, the thermal and mechanical data obtained from various irradiation tests and post-irradiation examinations were compared with the predictions of this code. In this study, INTA (instrumented test assembly) test in JOYO, PTM (power-to-melt) test in JOYO, EBR-II, FFTF and MTR in Harwell laboratory, and post-irradiation examinations on a number of PFR fuels, were used as verification data. (author)

Coding for dummies

CERN Document Server

Abraham, Nikhil

2015-01-01

Hands-on exercises help you learn to code like a pro No coding experience is required for Coding For Dummies,your one-stop guide to building a foundation of knowledge inwriting computer code for web, application, and softwaredevelopment. It doesn't matter if you've dabbled in coding or neverwritten a line of code, this book guides you through the basics.Using foundational web development languages like HTML, CSS, andJavaScript, it explains in plain English how coding works and whyit's needed. Online exercises developed by Codecademy, a leading online codetraining site, help hone coding skill

Report on FY15 alloy 617 code rules development

Energy Technology Data Exchange (ETDEWEB)

Sham, Sam [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jetter, Robert I [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hollinger, Greg [Becht Engineering Co., Inc., Liberty Corner, NJ (United States); Pease, Derrick [Becht Engineering Co., Inc., Liberty Corner, NJ (United States); Carter, Peter [Stress Engineering Services, Inc., Houston, TX (United States); Pu, Chao [Univ. of Tennessee, Knoxville, TN (United States); Wang, Yanli [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-09-01

Due to its strength at very high temperatures, up to 950°C (1742°F), Alloy 617 is the reference construction material for structural components that operate at or near the outlet temperature of the very high temperature gas-cooled reactors. However, the current rules in the ASME Section III, Division 5 Subsection HB, Subpart B for the evaluation of strain limits and creep-fatigue damage using simplified methods based on elastic analysis have been deemed inappropriate for Alloy 617 at temperatures above 650°C (1200°F) (Corum and Brass, Proceedings of ASME 1991 Pressure Vessels and Piping Conference, PVP-Vol. 215, p.147, ASME, NY, 1991). The rationale for this exclusion is that at higher temperatures it is not feasible to decouple plasticity and creep, which is the basis for the current simplified rules. This temperature, 650°C (1200°F), is well below the temperature range of interest for this material for the high temperature gas-cooled reactors and the very high temperature gas-cooled reactors. The only current alternative is, thus, a full inelastic analysis requiring sophisticated material models that have not yet been formulated and verified. To address these issues, proposed code rules have been developed which are based on the use of elastic-perfectly plastic (EPP) analysis methods applicable to very high temperatures. The proposed rules for strain limits and creep-fatigue evaluation were initially documented in the technical literature (Carter, Jetter and Sham, Proceedings of ASME 2012 Pressure Vessels and Piping Conference, papers PVP 2012 28082 and PVP 2012 28083, ASME, NY, 2012), and have been recently revised to incorporate comments and simplify their application. Background documents have been developed for these two code cases to support the ASME Code committee approval process. These background documents for the EPP strain limits and creep-fatigue code cases are documented in this report.

The history and development of nonlinear stellar pulsation codes

International Nuclear Information System (INIS)

Davis, C.G.

1987-01-01

This review is limited to the history and development of nonlinear stellar pulsation codes and methods. The narrative includes examples of practical interest in the application of these numerical methods to problems in stellar pulsation such as Cepheid mass discrepancy, the delineation of the RR Lyrae instability strip, and the question of the development of double-mode pulsation as observed in Cepheids, RR Lyrae and other variable stars. 15 refs

The Aster code; Code Aster

Energy Technology Data Exchange (ETDEWEB)

Delbecq, J.M

1999-07-01

The Aster code is a 2D or 3D finite-element calculation code for structures developed by the R and D direction of Electricite de France (EdF). This dossier presents a complete overview of the characteristics and uses of the Aster code: introduction of version 4; the context of Aster (organisation of the code development, versions, systems and interfaces, development tools, quality assurance, independent validation); static mechanics (linear thermo-elasticity, Euler buckling, cables, Zarka-Casier method); non-linear mechanics (materials behaviour, big deformations, specific loads, unloading and loss of load proportionality indicators, global algorithm, contact and friction); rupture mechanics (G energy restitution level, restitution level in thermo-elasto-plasticity, 3D local energy restitution level, KI and KII stress intensity factors, calculation of limit loads for structures), specific treatments (fatigue, rupture, wear, error estimation); meshes and models (mesh generation, modeling, loads and boundary conditions, links between different modeling processes, resolution of linear systems, display of results etc..); vibration mechanics (modal and harmonic analysis, dynamics with shocks, direct transient dynamics, seismic analysis and aleatory dynamics, non-linear dynamics, dynamical sub-structuring); fluid-structure interactions (internal acoustics, mass, rigidity and damping); linear and non-linear thermal analysis; steels and metal industry (structure transformations); coupled problems (internal chaining, internal thermo-hydro-mechanical coupling, chaining with other codes); products and services. (J.S.)

Modeling developments for the SAS4A and SASSYS computer codes

International Nuclear Information System (INIS)

Cahalan, J.E.; Wei, T.Y.C.

1990-01-01

The SAS4A and SASSYS computer codes are being developed at Argonne National Laboratory for transient analysis of liquid metal cooled reactors. The SAS4A code is designed to analyse severe loss-of-coolant flow and overpower accidents involving coolant boiling, Cladding failures, and fuel melting and relocation. Recent SAS4A modeling developments include extension of the coolant boiling model to treat sudden fission gas release upon pin failure, expansion of the DEFORM fuel behavior model to handle advanced cladding materials and metallic fuel, and addition of metallic fuel modeling capability to the PINACLE and LEVITATE fuel relocation models. The SASSYS code is intended for the analysis of operational and beyond-design-basis transients, and provides a detailed transient thermal and hydraulic simulation of the core, the primary and secondary coolant circuits, and the balance-of-plant, in addition to a detailed model of the plant control and protection systems. Recent SASSYS modeling developments have resulted in detailed representations of the balance of plant piping network and components, including steam generators, feedwater heaters and pumps, and the turbine. 12 refs., 2 tabs

Development of a dose assessment computer code for the NPP severe accident

International Nuclear Information System (INIS)

Cheong, Jae Hak

1993-02-01

A real-time emergency dose assessment computer code called KEDA (KAIST NPP Emergency Dose Assessment) has been developed for the NPP severe accident. A new mathematical model which can calculate cloud shine has been developed and implemented in the code. KEDA considers the specific Korean situations(complex topography, orientals' thyroid metabolism, continuous washout, etc.), and provides functions of dose-monitoring and automatic decision-making. To verify the code results, KEDA has been compared with an NRC officially certified code, RASCAL, for eight hypertical accident scenarios. Through the comparison, KEDA has been proved to provide reasonable results. Qualitative sensitivity analysis also the been performed for potentially important six input parameters, and the trends of the dose v.s. down-wind distance curve have been analyzed comparing with the physical phenomena occurred in the real atmosphere. The source term and meteorological conditions are turned out to be the most important input parameters. KEDA also has been applied to simulate Kori site and a hyperthetical accident with semi-real meteorological data has been simulated and analyzed

Development and assessment of a sub-channel code applicable for trans-critical transient of SCWR

International Nuclear Information System (INIS)

Liu, X.J.; Yang, T.; Cheng, X.

2013-01-01

Highlights: • A new sub-channel code COBRA-SC for SCWR is developed. • Pseudo two-phase method is employed to realize trans-critical transient calculation. • Good suitability of COBRA-SC is demonstrated by preliminary assessment. • The calculation results of COBRA-SC agree well with ATHLET code. -- Abstract: In the last few years, extensive R and D activities have been launched covering various aspects of supercritical water-cooled reactor (SCWR), especially the thermal-hydraulic analysis. Sub-channel code plays an indispensable role to predict the detail thermal-hydraulic behavior of the SCWR fuel assembly. This paper develops a new version of sub-channel code COBRA-SC based on the previous COBRA-IV code. The supercritical water property and heat transfer/pressure drop correlations under supercritical pressure are implemented to this code. Moreover, in order to simulate the trans-critical transient (the pressure undergo a decrease from the supercritical pressure to the subcritical pressure), pseudo two-phase method is employed in COBRA-SC code. This work is completed by introduction of a virtual two-phase region near the pseudo-critical line. A smooth transition of void fraction can be realized. In addition, several heat transfer correlations right underneath the critical point are introduced into this code to capture the heat transfer behavior during the trans-critical transient. Some experimental data from simple geometry, e.g. the single tube, small rod bundle, is used to validate and evaluate this new developed COBRA-SC code. The predicted results show a good agreement with the experimental data, demonstrating good feasibility of this code for SCWR condition. A code to code comparison between COBRA-SC and ATHLET for a blowdown transient of a small fuel assembly is also presented and discussed in this paper

Report on nuclear industry quality assurance procedures for safety analysis computer code development and use

International Nuclear Information System (INIS)

Sheron, B.W.; Rosztoczy, Z.R.

1980-08-01

As a result of a request from Commissioner V. Gilinsky to investigate in detail the causes of an error discovered in a vendor Emergency Core Cooling System (ECCS) computer code in March, 1978, the staff undertook an extensive investigation of the vendor quality assurance practices applied to safety analysis computer code development and use. This investigation included inspections of code development and use practices of the four major Light Water Reactor Nuclear Steam Supply System vendors and a major reload fuel supplier. The conclusion reached by the staff as a result of the investigation is that vendor practices for code development and use are basically sound. A number of areas were identified, however, where improvements to existing vendor procedures should be made. In addition, the investigation also addressed the quality assurance (QA) review and inspection process for computer codes and identified areas for improvement

Development of a thermal-hydraulic code for reflood analysis in a PWR experimental loop

International Nuclear Information System (INIS)

Alves, Sabrina P.; Mesquita, Amir Z.; Rezende, Hugo C.; Palma, Daniel A.P.

2017-01-01

A process of fundamental importance in the event of Loss of Coolant Accident (LOCA) in Pressurized Water nuclear Reactors (PWR) is the reflood of the core or rewetting of nuclear fuels. The Nuclear Technology Development Center (CDTN) has been developing since the 70’s programs to allow Brazil to become independent in the field of reactor safety analysis. To that end, in the 80’s was designed, assembled and commissioned one Rewetting Test Facility (ITR in Portuguese). This facility aims to investigate the phenomena involved in the thermal hydraulic reflood phase of a Loss of Coolant Accident in a PWR nuclear reactor. This work aim is the analysis of physical and mathematical models governing the rewetting phenomenon, and the development a thermo-hydraulic simulation code of a representative experimental circuit of the PWR reactors core cooling channels. It was possible to elaborate and develop a code called REWET. The results obtained with REWET were compared with the experimental results of the ITR, and with the results of the Hydroflut code, that was the old program previously used. An analysis was made of the evolution of the wall temperature of the test section as well as the evolution of the front for two typical tests using the two codes calculation, and experimental results. The result simulated by REWET code for the rewetting time also came closer to the experimental results more than those calculated by Hydroflut code. (author)

Development of a thermal-hydraulic code for reflood analysis in a PWR experimental loop

Energy Technology Data Exchange (ETDEWEB)

Alves, Sabrina P.; Mesquita, Amir Z.; Rezende, Hugo C., E-mail: sabrinapral@gmail.com, E-mail: amir@cdtn.brm, E-mail: hcr@cdtn.br, E-mail: hcr@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Palma, Daniel A.P., E-mail: dapalma@cnen.gov.br [Comissão Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil)

2017-07-01

A process of fundamental importance in the event of Loss of Coolant Accident (LOCA) in Pressurized Water nuclear Reactors (PWR) is the reflood of the core or rewetting of nuclear fuels. The Nuclear Technology Development Center (CDTN) has been developing since the 70’s programs to allow Brazil to become independent in the field of reactor safety analysis. To that end, in the 80’s was designed, assembled and commissioned one Rewetting Test Facility (ITR in Portuguese). This facility aims to investigate the phenomena involved in the thermal hydraulic reflood phase of a Loss of Coolant Accident in a PWR nuclear reactor. This work aim is the analysis of physical and mathematical models governing the rewetting phenomenon, and the development a thermo-hydraulic simulation code of a representative experimental circuit of the PWR reactors core cooling channels. It was possible to elaborate and develop a code called REWET. The results obtained with REWET were compared with the experimental results of the ITR, and with the results of the Hydroflut code, that was the old program previously used. An analysis was made of the evolution of the wall temperature of the test section as well as the evolution of the front for two typical tests using the two codes calculation, and experimental results. The result simulated by REWET code for the rewetting time also came closer to the experimental results more than those calculated by Hydroflut code. (author)

Development of a multi-grid FDTD code for three-dimensional simulation of large microwave sintering experiments

Energy Technology Data Exchange (ETDEWEB)

White, M.J.; Iskander, M.F. [Univ. of Utah, Salt Lake City, UT (United States). Electrical Engineering Dept.; Kimrey, H.D. [Oak Ridge National Lab., TN (United States)

1996-12-31

The Finite-Difference Time-Domain (FDTD) code available at the University of Utah has been used to simulate sintering of ceramics in single and multimode cavities, and many useful results have been reported in literature. More detailed and accurate results, specifically around and including the ceramic sample, are often desired to help evaluate the adequacy of the heating procedure. In electrically large multimode cavities, however, computer memory requirements limit the number of the mathematical cells, and the desired resolution is impractical to achieve due to limited computer resources. Therefore, an FDTD algorithm which incorporates multiple-grid regions with variable-grid sizes is required to adequately perform the desired simulations. In this paper the authors describe the development of a three-dimensional multi-grid FDTD code to help focus a large number of cells around the desired region. Test geometries were solved using a uniform-grid and the developed multi-grid code to help validate the results from the developed code. Results from these comparisons, as well as the results of comparisons between the developed FDTD code and other available variable-grid codes are presented. In addition, results from the simulation of realistic microwave sintering experiments showed improved resolution in critical sites inside the three-dimensional sintering cavity. With the validation of the FDTD code, simulations were performed for electrically large, multimode, microwave sintering cavities to fully demonstrate the advantages of the developed multi-grid FDTD code.

Recent Developments in the Code RITRACKS (Relativistic Ion Tracks)

Science.gov (United States)

Plante, Ianik; Ponomarev, Artem L.; Blattnig, Steve R.

2018-01-01

The code RITRACKS (Relativistic Ion Tracks) was developed to simulate detailed stochastic radiation track structures of ions of different types and energies. Many new capabilities were added to the code during the recent years. Several options were added to specify the times at which the tracks appear in the irradiated volume, allowing the simulation of dose-rate effects. The code has been used to simulate energy deposition in several targets: spherical, ellipsoidal and cylindrical. More recently, density changes as well as a spherical shell were implemented for spherical targets, in order to simulate energy deposition in walled tissue equivalent proportional counters. RITRACKS is used as a part of the new program BDSTracks (Biological Damage by Stochastic Tracks) to simulate several types of chromosome aberrations in various irradiation conditions. The simulation of damage to various DNA structures (linear and chromatin fiber) by direct and indirect effects has been improved and is ongoing. Many improvements were also made to the graphic user interface (GUI), including the addition of several labels allowing changes of units. A new GUI has been added to display the electron ejection vectors. The parallel calculation capabilities, notably the pre- and post-simulation processing on Windows and Linux machines have been reviewed to make them more portable between different systems. The calculation part is currently maintained in an Atlassian Stash® repository for code tracking and possibly future collaboration.

Development Of The Computer Code For Comparative Neutron Activation Analysis

International Nuclear Information System (INIS)

Purwadi, Mohammad Dhandhang

2001-01-01

The qualitative and quantitative chemical analysis with Neutron Activation Analysis (NAA) is an importance utilization of a nuclear research reactor, and this should be accelerated and promoted in application and its development to raise the utilization of the reactor. The application of Comparative NAA technique in GA Siwabessy Multi Purpose Reactor (RSG-GAS) needs special (not commercially available yet) soft wares for analyzing the spectrum of multiple elements in the analysis at once. The application carried out using a single spectrum software analyzer, and comparing each result manually. This method really degrades the quality of the analysis significantly. To solve the problem, a computer code was designed and developed for comparative NAA. Spectrum analysis in the code is carried out using a non-linear fitting method. Before the spectrum analyzed, it was passed to the numerical filter which improves the signal to noise ratio to do the deconvolution operation. The software was developed using the G language and named as PASAN-K The testing result of the developed software was benchmark with the IAEA spectrum and well operated with less than 10 % deviation

Application of software engineering to development of reactor-safety codes

International Nuclear Information System (INIS)

Wilburn, N.P.; Niccoli, L.G.

1980-11-01

As a result of the drastically increasing cost of software and the lack of an engineering approach, the technology of Software Engineering is being developed. Software Engineering provides an answer to the increasing cost of developing and maintaining software. It has been applied extensively in the business and aerospace communities and is just now being applied to the development of scientific software and, in particular, to the development of reactor safety codes at HEDL

CENER/NREL Collaboration in Testing Facility and Code Development: Cooperative Research and Development Final Report, CRADA Number CRD-06-207

Energy Technology Data Exchange (ETDEWEB)

Moriarty, P.

2014-11-01

Under the funds-in CRADA agreement, NREL and CENER will collaborate in the areas of blade and drivetrain testing facility development and code development. The project shall include NREL assisting in the review and instruction necessary to assist in commissioning the new CENER blade test and drivetrain test facilities. In addition, training will be provided by allowing CENER testing staff to observe testing and operating procedures at the NREL blade test and drivetrain test facilities. CENER and NREL will exchange blade and drivetrain facility and equipment design and performance information. The project shall also include exchanging expertise in code development and data to validate numerous computational codes.

Development of the SCHAMBETA code for scoping analysis of HCDA

Energy Technology Data Exchange (ETDEWEB)

Suk, Soo Dong; Hahn, D. H

2000-06-01

A computer code, SCHAMBETA(Scoping Code for HCDA Analysis using Modified Bethe-Tait Method), is developed to investigate the core disassembly process following a meltdown accident in the framework of a mofified Bethe-Tait method as part of the scoping analysis work to demonstrate the inherent safety of conceptual designs of Korea Advanced Liquid Metal Reactor(KALIMER), A 150 Mwe pool-type sodium cooled prototype fast reactor that uses U-Pu-Zr metallic fuel. The methodologies adopted in the code ared particularly useful to perform various parametric studies for better understanding of core disassembly process of liquid metal fast reactors as well as to estimate upper-limit values of the energy release resulting from a power excursion. In the SCHAMBETA code, the core kinetics and hydraulic behavior of the KALIMER is followed over the period of the super-prompt critical power excursion induced by the ramp reactivity insertion, starting at the time that the sodium-voided core reaches the melting temperature of the metallic fuels. For this purpose, the equations of state of pressure-energy density relationship are derived for the saturated-vapor as well as the solid liquid of metallic uranium fuel, and implemenmted into the formulations of the disassembly reactivity. Mathematical formulations are then developed, in the framework of Modified Bethe-Tait method, in a form relevant to utilize the improved equations of state as well as to consider Doppler effects, for scoping analysis of the super-prompt-critical power excursions driven by a specified rate of reactivity insertion.

Recent developments of JAEA's Monte Carlo Code MVP for reactor physics applications

International Nuclear Information System (INIS)

Nagaya, Y.; Okumura, K.; Mori, T.

2013-01-01

MVP is a general-purpose continuous-energy Monte Carlo code for neutron and photon transport calculations that has been developed since the late 1980's at Japan Atomic Energy Agency (JAEA, formerly JAERI). The MVP code is designed for nuclear reactor applications such as reactor core design/analysis, criticality safety and reactor shielding. This paper describes the MVP code and present its latest developments. Among the new capabilities of MVP we find: -) the perturbation method has been implemented for the change in k(eff); -) the eigenvalue calculations can be performed with an explicit treatment of delayed neutrons in which their fission spectra are taken into account; -) the capability of tallying the scattering matrix (group-to-group scattering cross sections); -) the implementation of an exact model for resonance elastic scattering; and -) a Monte Carlo perturbation technique is used to calculate reactor kinetics parameters

Development of a CAD-based neutron transport code with the method of characteristics

International Nuclear Information System (INIS)

Chen Zhenping; Wang Dianxi; He Tao; Wang Guozhong; Zheng Huaqing

2012-01-01

The main problem determining whether the method of characteristics (MOC) can be used in complicated and highly heterogeneous geometry is how to combine an effective geometry processing method with MOC. In this study, a new idea making use of MCAM, which is a Mutlti-Calculation Automatic Modeling for Neutronics and Radiation Transport program developed by FDS Team, for geometry description and ray tracing of particle transport was brought forward to solve the geometry problem mentioned above. Based on the theory and approach as the foregoing statement, a two dimensional neutron transport code was developed which had been integrated into VisualBUS, developed by FDS Team. Several benchmarks were used to verify the validity of the code and the numerical results were coincident with the reference values very well, which indicated the accuracy and feasibility of the method and the MOC code. (authors)

Preliminary Development of the MARS/FREK Spatial Kinetics Coupled System Code for Square Fueled Fast Reactor Applications

International Nuclear Information System (INIS)

Bae, Moo Hoon; Joo, Han Gyu

2009-01-01

Incorporation of a three-dimensional (3-D) reactor kinetics model into a system thermal-hydraulic (T/H) code enhances the capability to perform realistic analyses of the core neutronic behavior and the plant system dynamics which are coupled each other. For this advantage, several coupled system T/H and spatial kinetics codes, such as RELAP/PARCS, RELAP5/ PANBOX, and MARS/MASTER have been developed. These codes, however, so far limited to LWR applications. The objective of this work is to develop such a coupled code for fast reactor applications. Particularly, applications to lead-bismuth eutectic (LBE) cooled fast reactor are of interest which employ open square lattices. A fast reactor kinetics code applicable to square fueled cores called FREK is coupled the LBE version of the MARS code. The MARS/MASTER coupled code is used as the reference for the integration. The coupled code MARS/FREK is examined for a conceptual reactor called P-DEMO which is being developed by NUTRECK. In order to check the validity of the coupled code, however, the OECD MSLB benchmark exercise III calculation is solved first

Development, validation and application of NAFA 2D-CFD code

International Nuclear Information System (INIS)

Vaidya, A.M.; Maheshwari, N.K.; Vijayan, P.K.; Saha, D.

2010-01-01

A 2D axi-symmetric code named NAFA (Version 1.0) is developed for studying the pipe flow under various conditions. It can handle laminar/ turbulent flows, with or without heat transfer, under sub-critical/super-critical conditions. The code solves for momentum, energy equations with standard k-ε turbulence model (with standard wall functions). It solves pipe flow subjected to 'velocity inlet', 'wall', 'axis' and 'pressure outlet' boundary conditions. It is validated for several cases by comparing its results with experimental data/analytical solutions/correlations. The code has excellent convergence characteristics as verified from fall of equation residual in each case. It has proven capability of generating mesh independent results for laminar as well as turbulent flows. The code is applied to supercritical flows. For supercritical flows, the effect of mesh size on prediction of heat transfer coefficient is studied. With grid refinement, the Y + reduces and reaches the limiting value of 11.63. Hence the accuracy is found to increase with grid refinement. NAFA is able to qualitatively predict the effect of heat flux and operating pressure on heat transfer coefficient. The heat transfer coefficient matches well with experimental values under various conditions. (author)

NIMROD: A Customer Focused, Team Driven Approach for Fusion Code Development

Science.gov (United States)

Karandikar, H. M.; Schnack, D. D.

1996-11-01

NIMROD is a new code that will be used for the analysis of existing fusion experiments, prediction of operational limits, and design of future devices. An approach called Integrated Product Development (IPD) is being used for the development of NIMROD. It is a dramatic departure from existing practice in the fusion program. Code development is being done by a self-directed, multi-disciplinary, multi-institutional team that consists of experts in plasma theory, experiment, computational physics, and computer science. Customer representatives (ITER, US experiments) are an integral part of the team. The team is using techniques such as Quality Function Deployment (QFD), Pugh Concept Selection, Rapid Prototyping, and Risk Management, during the design phase of NIMROD. Extensive use is made of communication and internet technology to support collaborative work. Our experience with using these team techniques for such a complex software development project will be reported.

Methods for the development of large computer codes under LTSS

International Nuclear Information System (INIS)

Sicilian, J.M.

1977-06-01

TRAC is a large computer code being developed by Group Q-6 for the analysis of the transient thermal hydraulic behavior of light-water nuclear reactors. A system designed to assist the development of TRAC is described. The system consists of a central HYDRA dataset, R6LIB, containing files used in the development of TRAC, and a file maintenance program, HORSE, which facilitates the use of this dataset

Development of dynamic simulation code for fuel cycle fusion reactor

Energy Technology Data Exchange (ETDEWEB)

Aoki, Isao; Seki, Yasushi [Department of Fusion Engineering Research, Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki (Japan); Sasaki, Makoto; Shintani, Kiyonori; Kim, Yeong-Chan

1999-02-01

A dynamic simulation code for fuel cycle of a fusion experimental reactor has been developed. The code follows the fuel inventory change with time in the plasma chamber and the fuel cycle system during 2 days pulse operation cycles. The time dependence of the fuel inventory distribution is evaluated considering the fuel burn and exhaust in the plasma chamber, purification and supply functions. For each subsystem of the plasma chamber and the fuel cycle system, the fuel inventory equation is written based on the equation of state considering the fuel burn and the function of exhaust, purification, and supply. The processing constants of subsystem for steady states were taken from the values in the ITER Conceptual Design Activity (CDA) report. Using this code, the time dependence of the fuel supply and inventory depending on the burn state and subsystem processing functions are shown. (author)

A development of containment performance analysis methodology using GOTHIC code

Energy Technology Data Exchange (ETDEWEB)

Lee, B. C.; Yoon, J. I. [Future and Challenge Company, Seoul (Korea, Republic of); Byun, C. S.; Lee, J. Y. [Korea Electric Power Research Institute, Taejon (Korea, Republic of); Lee, J. Y. [Seoul National University, Seoul (Korea, Republic of)

2003-10-01

In a circumstance that well-established containment pressure/temperature analysis code, CONTEMPT-LT treats the reactor containment as a single volume, this study introduces, as an alternative, the GOTHIC code for an usage on multi-compartmental containment performance analysis. With a developed GOTHIC methodology, its applicability is verified for containment performance analysis for Korean Nuclear Unit 1. The GOTHIC model for this plant is simply composed of 3 compartments including the reactor containment and RWST. In addition, the containment spray system and containment recirculation system are simulated. As a result of GOTHIC calculation, under the same assumptions and conditions as those in CONTEMPT-LT, the GOTHIC prediction shows a very good result; pressure and temperature transients including their peaks are nearly the same. It can be concluded that the GOTHIC could provide reasonable containment pressure and temperature responses if considering the inherent conservatism in CONTEMPT-LT code.

A development of containment performance analysis methodology using GOTHIC code

International Nuclear Information System (INIS)

Lee, B. C.; Yoon, J. I.; Byun, C. S.; Lee, J. Y.; Lee, J. Y.

2003-01-01

In a circumstance that well-established containment pressure/temperature analysis code, CONTEMPT-LT treats the reactor containment as a single volume, this study introduces, as an alternative, the GOTHIC code for an usage on multi-compartmental containment performance analysis. With a developed GOTHIC methodology, its applicability is verified for containment performance analysis for Korean Nuclear Unit 1. The GOTHIC model for this plant is simply composed of 3 compartments including the reactor containment and RWST. In addition, the containment spray system and containment recirculation system are simulated. As a result of GOTHIC calculation, under the same assumptions and conditions as those in CONTEMPT-LT, the GOTHIC prediction shows a very good result; pressure and temperature transients including their peaks are nearly the same. It can be concluded that the GOTHIC could provide reasonable containment pressure and temperature responses if considering the inherent conservatism in CONTEMPT-LT code

Development of computer code on sodium-water reaction products transport

International Nuclear Information System (INIS)

Arikawa, H.; Yoshioka, N.; Suemori, M.; Nishida, K.

1988-01-01

The LMFBR concept eliminating the secondary sodium system has been considered to be one of the most promissing concepts for offering cost reductions. In this reactor concept, the evaluation of effects on reactor core by the sodium-water reaction products (SWRPs) during sodium-water reaction at primary steam generator becomes one of the major safety issues. In this study, the calculation code was developed as the first step of the processes of establishing the evaluation method for SWRP effects. The calculation code, called SPROUT, simulates the SWRPs transport and distribution in primary sodium system using the system geometry, thermal hydraulic data and sodium-water reacting conditions as input. This code principally models SWRPs behavior. The paper contain the modelings for SWRPs behaviors, with solution, precipation, deposition and so on, and the results and discussions of the demonstration calculation for a typical FBR plant eliminating the secondary sodium system

Development of the biosphere code BIOMOD: final report

International Nuclear Information System (INIS)

Kane, P.

1983-05-01

Final report to DoE on the development of the biosphere code BIOMOD. The work carried out under the contract is itemised. Reference is made to the six documents issued along with the final report. These consist of two technical notes issued as interim consultative documents, a user's guide and a programmer's guide to BIOMOD, a database description, program test document and a technical note entitled ''BIOMOD - preliminary findings''. (author)

Development, verification and validation of the fuel channel behaviour computer code FACTAR

Energy Technology Data Exchange (ETDEWEB)

Westbye, C J; Brito, A C; MacKinnon, J C; Sills, H E; Langman, V J [Ontario Hydro, Toronto, ON (Canada)

1996-12-31

FACTAR (Fuel And Channel Temperature And Response) is a computer code developed to simulate the transient thermal and mechanical behaviour of 37-element or 28-element fuel bundles within a single CANDU fuel channel for moderate loss of coolant accident conditions including transition and large break LOCA`s (loss of coolant accidents) with emergency coolant injection assumed available. FACTAR`s predictions of fuel temperature and sheath failure times are used to subsequent assessment of fission product releases and fuel string expansion. This paper discusses the origin and development history of FACTAR, presents the mathematical models and solution technique, the detailed quality assurance procedures that are followed during development, and reports the future development of the code. (author). 27 refs., 3 figs.

Development and validation of computer codes for analysis of PHWR containment behaviour

International Nuclear Information System (INIS)

Markandeya, S.G.; Haware, S.K.; Ghosh, A.K.; Venkat Raj, V.

1997-01-01

In order to ensure that the design intent of the containment of Indian Pressurised Heavy Water Reactors (IPHWRs) is met, both analytical and experimental studies are being pursued at BARC. As a part of analytical studies, computer codes for predicting the behaviour of containment under various accident scenarios are developed/adapted. These include codes for predicting 1) pressure, temperature transients in the containment following either Loss of Coolant Accident (LOCA) or Main Steam Line Break (MSLB), 2) hydrogen behaviour in respect of its distribution, combustion and the performance of proposed mitigation systems, and 3) behaviour of fission product aerosols in the piping circuits of the primary heat transport system and in the containment. All these codes have undergone thorough validation using data obtained from in-house test facilities or from international sources. Participation in the International Standard Problem (ISP) exercises has also helped in validation of the codes. The present paper briefly describes some of these codes and the various exercises performed for their validation. (author)

Development of a CFD Code for Analysis of Fluid Dynamic Forces in Seals

Science.gov (United States)

Athavale, Mahesh M.; Przekwas, Andrzej J.; Singhal, Ashok K.

1991-01-01

The aim is to develop a 3-D computational fluid dynamics (CFD) code for the analysis of fluid flow in cylindrical seals and evaluation of the dynamic forces on the seals. This code is expected to serve as a scientific tool for detailed flow analysis as well as a check for the accuracy of the 2D industrial codes. The features necessary in the CFD code are outlined. The initial focus was to develop or modify and implement new techniques and physical models. These include collocated grid formulation, rotating coordinate frames and moving grid formulation. Other advanced numerical techniques include higher order spatial and temporal differencing and an efficient linear equation solver. These techniques were implemented in a 2D flow solver for initial testing. Several benchmark test cases were computed using the 2D code, and the results of these were compared to analytical solutions or experimental data to check the accuracy. Tests presented here include planar wedge flow, flow due to an enclosed rotor, and flow in a 2D seal with a whirling rotor. Comparisons between numerical and experimental results for an annular seal and a 7-cavity labyrinth seal are also included.

Development of Unified Code for Environmental Research by Neutron Activation Analysis

Energy Technology Data Exchange (ETDEWEB)

Cho, Seung Yeon; Kim, Young Sik; Lee, Sang Mi; Chung, Sang Uk; Lee, Kyu Sung; Kang, Sang Hun; Cheon, Ki Hong [Yonsei University, Seoul (Korea, Republic of)

1997-07-01

Three codes were developed to improve accuracy and precision of neutron activation analysis with the adoption of IAEA`s recommended `GANAAS` program which has the better peak identification and efficiency calibration algorithm than the currently using commercial program. Quantitative analytical ability of trace element was improved with the codes such that the number of detectable elements including environmentally important elements was increased. Small and over lapped peaks can be detected more efficiently with the good peak shape calibration(energy dependence on peak height, peak base width and FWHM). Several efficiency functions were added to determine the detector efficiency more accurately which was the main source of error in neutron activation analysis. Errors caused by nuclear data themselves were reduced with the introduction of ko method. New graphical program called `POWER NAA` was developed for the recent personal computer environment, Window 95, and for the data compatibility. It also reduced the error caused by operator`s mistake with the easy and comfortable operation of the code. 11 refs., 3 tabs., 9 figs. (author)

Recent development for the ITS code system: Parallel processing and visualization

International Nuclear Information System (INIS)

Fan, W.C.; Turner, C.D.; Halbleib, J.A. Sr.; Kensek, R.P.

1996-01-01

A brief overview is given for two software developments related to the ITS code system. These developments provide parallel processing and visualization capabilities and thus allow users to perform ITS calculations more efficiently. Timing results and a graphical example are presented to demonstrate these capabilities

Gas cloud explosions and their effect on nuclear power plant, basic development of explosion codes

International Nuclear Information System (INIS)

Hall, S.F.; Martin, D.; MacKenzie, J.

1985-01-01

The study of factors influencing the pressure and velocity fields produced by the burning of flammable substances has been in progress at SRD for some years. This paper describes an extension of these studies by using existing codes for a parametric survey, and modifying codes to produce more realistic representations of explosions and developing a two dimensional combustion code, FLARE. The one dimensional combustion code, GASEX1, has been used to determine the pressure from a burning gas cloud for a number of different fuels, concentrations and burning velocities. The code was modified so that gas concentrations could be modelled. Results for concentration gradients showed the pressure depended on local conditions and the burning velocity. The two dimensional code, GASEX2, was modified to model the interaction of pressure waves with structures. It was used, with results from GASEX1, to model the interaction of a pressure wave from the combustion of a gas cloud with a rigid structure representing a nuclear power plant. The two dimensional code FLARE has been developed to model the interaction of flames and pressure waves with structures. The code incorporates a simple turbulence model with a turbulence dependent reaction rate. Validation calculations have been carried out for the code. (author)

Development of ECOREA-II code for the evaluation of exposures from radionuclides through food Chain

International Nuclear Information System (INIS)

Yu, Dong Han; Lee, Han Soo

2002-01-01

The release of radionuclides from nuclear facilities following an accident into air results in human exposures by intakes of plant products such as rice, vegetables and/or animal products including meat, milk and eggs from contaminated soil. In order to evaluate such exposures from radioactive substances, it is essential to mathematically predict the behavior of these substances in the environments. A computer code, named 'ECOREA-II' is developing to assess human exposures through food chain of such substances in Korea. ECOREA-II code has a dynamic compartment-based model at its core, the graphical user interface (GUI) for the selection of input parameters and result displays on personal computers, and generation of data files for a GIS (Graphical Information System). Even the code is developed mostly based currently available models and/or codes, a new model is included for the time-dependent growth dilution in a vegetation part. Effort on The development of the code is towards the prediction of the behavior and pattern of radionuclides in a specific food chain condition in Korea. Finally, it provides a more user-friendly environment such as GUI developed based on the VBA(Visual Basic Application) for personal users. Therefore, the current code, when more fully developed, is expected to increase the understanding of environmental safety assessment of nuclear facilities following an accident and provide a reasonable regulatory guideline with respect to food safety issues

The PARTRAC code: Status and recent developments

Science.gov (United States)

Friedland, Werner; Kundrat, Pavel

Biophysical modeling is of particular value for predictions of radiation effects due to manned space missions. PARTRAC is an established tool for Monte Carlo-based simulations of radiation track structures, damage induction in cellular DNA and its repair [1]. Dedicated modules describe interactions of ionizing particles with the traversed medium, the production and reactions of reactive species, and score DNA damage determined by overlapping track structures with multi-scale chromatin models. The DNA repair module describes the repair of DNA double-strand breaks (DSB) via the non-homologous end-joining pathway; the code explicitly simulates the spatial mobility of individual DNA ends in parallel with their processing by major repair enzymes [2]. To simulate the yields and kinetics of radiation-induced chromosome aberrations, the repair module has been extended by tracking the information on the chromosome origin of ligated fragments as well as the presence of centromeres [3]. PARTRAC calculations have been benchmarked against experimental data on various biological endpoints induced by photon and ion irradiation. The calculated DNA fragment distributions after photon and ion irradiation reproduce corresponding experimental data and their dose- and LET-dependence. However, in particular for high-LET radiation many short DNA fragments are predicted below the detection limits of the measurements, so that the experiments significantly underestimate DSB yields by high-LET radiation [4]. The DNA repair module correctly describes the LET-dependent repair kinetics after (60) Co gamma-rays and different N-ion radiation qualities [2]. First calculations on the induction of chromosome aberrations have overestimated the absolute yields of dicentrics, but correctly reproduced their relative dose-dependence and the difference between gamma- and alpha particle irradiation [3]. Recent developments of the PARTRAC code include a model of hetero- vs euchromatin structures to enable

SCDAP/RELAP5/MOD3 code development and assessment

International Nuclear Information System (INIS)

Allison, C.M.; Heath, C.H.; Siefken, L.J.; Hohorst, J.K.

1991-01-01

The SCDAP/RELAP5/MOD3 computer code is designed to describe the overall reactor coolant system (RCS) thermal-hydraulic response, core damage progression, and fission product release and transport during severe accidents. The code is being developed at the Idaho National Engineering Laboratory (INEL) under the primary sponsorship of the Office of Nuclear Regulatory Research of the Nuclear Regulatory Commission (NRC). SCDAP/RELAP5/MOD3, created in January, 1991, is the result of merging RELAP5/MOD3 with SCDAP and TRAP-MELT models from SCDAP/RELAP5/MOD2.5. The RELAP5 models calculate the overall RCS thermal-hydraulics, control system interactions, reactor kinetics, and the transport of noncondensible gases, fission products, and aerosols. The SCDAP models calculate the damage progression in the core structures, the formation, heatup, and melting of debris, and the creep rupture failure of the lower head and other RCS structures. The TRAP-MELT models calculate the deposition of fission products upon aerosols or structural surfaces; the formation, growth, or deposition of aerosols; and the evaporation of species from surfaces. The systematic assessment of modeling uncertainties in SCDAP/RELAP5 code is currently underway. This assessment includes (a) the evaluation of code-to-data comparisons using stand-alone SCDAP and SCDAP/RELAP5/MOD3, (b) the estimation of modeling and experimental uncertainties, and (c) the determination of the influence of those uncertainties on predicted severe accident behavior

The FLUKA code for space applications Recent developments

CERN Document Server

Andersen, V; Battistoni, G; Campanella, M; Carboni, M; Cerutti, F; Empl, A; Fassò, A; Ferrari, A; Gadioli, E; Garzelli, M V; Lee, K; Ottolenghi, A; Pelliccioni, M; Pinsky, L S; Ranft, J; Roesler, S; Sala, P R; Wilson, T L

2004-01-01

The FLUKA Monte Carlo transport code is widely used for fundamental research, radioprotection and dosimetry, hybrid nuclear energy system and cosmic ray calculations. The validity of its physical models has been benchmarked against a variety of experimental data over a wide range of energies, ranging from accelerator data to cosmic ray showers in the earth atmosphere. The code is presently undergoing several developments in order to better fit the needs of space applications. The generation of particle spectra according to up-to- date cosmic ray data as well as the effect of the solar and geomagnetic modulation have been implemented and already successfully applied to a variety of problems. The implementation of suitable models for heavy ion nuclear interactions has reached an operational stage. At medium/high energy FLUKA is using the DPMJET model. The major task of incorporating heavy ion interactions from a few GeV/n down to the threshold for inelastic collisions is also progressing and promising results h...

Development and Verification of the Computer Codes for the Fast Reactors Nuclear Safety Justification

International Nuclear Information System (INIS)

Kisselev, A.E.; Mosunova, N.A.; Strizhov, V.F.

2015-01-01

The information on the status of the work on development of the system of the nuclear safety codes for fast liquid metal reactors is presented in paper. The purpose of the work is to create an instrument for NPP neutronic, thermohydraulic and strength justification including human and environment radiation safety. The main task that is to be solved by the system of codes developed is the analysis of the broad spectrum of phenomena taking place on the NPP (including reactor itself, NPP components, containment rooms, industrial site and surrounding area) and analysis of the impact of the regular and accidental releases on the environment. The code system is oriented on the ability of fully integrated modeling of the NPP behavior in the coupled definition accounting for the wide range of significant phenomena taking place on the NPP under normal and accident conditions. It is based on the models that meet the state-of-the-art knowledge level. The codes incorporate advanced numerical methods and modern programming technologies oriented on the high-performance computing systems. The information on the status of the work on verification of the separate codes of the system of codes is also presented. (author)

Theory and code development for evaluation of tritium retention and exhaust in fusion reactor

Energy Technology Data Exchange (ETDEWEB)

Ohya, Kaoru; Inai, Kensuke [Univ. of Tokushima, Institute of Technology and Science, Tokushima, Tokushima (Japan); Shimizu, Katsuhiro; Takizuka, Tomonori; Kawashima, Hisato; Hoshino, Kazuo [Japan Atomic Energy Agency, Fusion Research and Development Directorate, Naka, Ibaraki (Japan); Hatayama, Akiyoshi; Toma, Mitsunori [Keio Univ., Faculty of Science and Technology, Yokohama, Kanagawa (Japan); Tomita, Yukihiro; Kawamura, Gakushi; Ashikawa, Naoko; Nakamura, Hiroaki; Ito, Atsushi; Kato, Daiji [National Inst. for Fusion Science, Toki, Gifu (Japan); Tanaka, Yasunori [Kanazawa Univ., College of Science and Engineering, Kanazawa, Ishikawa (Japan); Ono, Tadayoshi; Muramoto, Tetsuya [Okayama Univ. of Science, Faculty of Informatics, Okayama, Okayama (Japan); Kenmotsu, Takahiro [Doshisha Univ., Faculty of Life and Medical Science, Kiyotanabe, Kyoto (Japan)

2009-10-15

As a part of the grant-in-aid for scientific research on priority areas entitled 'frontiers of tritium researches toward fusion reactors', coordinated three research programs on the theory and code development for evaluation of tritium retention and exhaust in fusion reactor have been conducted by the A02 team. They include: (1) Tritium transport in fusion plasmas and the adsorption and desorption property of tritium in plasma-facing components. (2) Behavior of dusts in fusion plasmas and their adsorption property of tritium. (3) Development of computer codes to simulate tritium retention in and release from plasma-facing materials. In order to study these issues, considerable effort has been paid to the development of computer codes and the database system. (J.P.N.)

Theory and code development for evaluation of tritium retention and exhaust in fusion reactor

International Nuclear Information System (INIS)

Ohya, Kaoru; Inai, Kensuke; Shimizu, Katsuhiro; Takizuka, Tomonori; Kawashima, Hisato; Hoshino, Kazuo; Hatayama, Akiyoshi; Toma, Mitsunori; Tomita, Yukihiro; Kawamura, Gakushi; Ashikawa, Naoko; Nakamura, Hiroaki; Ito, Atsushi; Kato, Daiji; Tanaka, Yasunori; Ono, Tadayoshi; Muramoto, Tetsuya; Kenmotsu, Takahiro

2009-01-01

As a part of the grant-in-aid for scientific research on priority areas entitled 'frontiers of tritium researches toward fusion reactors', coordinated three research programs on the theory and code development for evaluation of tritium retention and exhaust in fusion reactor have been conducted by the A02 team. They include: (1) Tritium transport in fusion plasmas and the adsorption and desorption property of tritium in plasma-facing components. (2) Behavior of dusts in fusion plasmas and their adsorption property of tritium. (3) Development of computer codes to simulate tritium retention in and release from plasma-facing materials. In order to study these issues, considerable effort has been paid to the development of computer codes and the database system. (J.P.N.)

Development of 'SKYSHINE-CG' code. A line-beam method code equipped with combinatorial geometry routine

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, Takahiro; Ochiai, Katsuharu [Plant and System Planning Department, Toshiba Corporation, Yokohama, Kanagawa (Japan); Uematsu, Mikio; Hayashida, Yoshihisa [Department of Nuclear Engineering, Toshiba Engineering Corporation, Yokohama, Kanagawa (Japan)

2000-03-01

A boiling water reactor (BWR) plant has a single loop coolant system, in which main steam generated in the reactor core proceeds directly into turbines. Consequently, radioactive {sup 16}N (6.2 MeV photon emitter) contained in the steam contributes to gamma-ray skyshine dose in the vicinity of the BWR plant. The skyshine dose analysis is generally performed with the line-beam method code SKYSHINE, in which calculational geometry consists of a rectangular turbine building and a set of isotropic point sources corresponding to an actual distribution of {sup 16}N sources. For the purpose of upgrading calculational accuracy, the SKYSHINE-CG code has been developed by incorporating the combinatorial geometry (CG) routine into the SKYSHINE code, so that shielding effect of in-building equipment can be properly considered using a three-dimensional model composed of boxes, cylinders, spheres, etc. Skyshine dose rate around a 500 MWe BWR plant was calculated with both SKYSHINE and SKYSHINE-CG codes, and the calculated results were compared with measured data obtained with a NaI(Tl) scintillation detector. The C/E values for SKYSHINE-CG calculation were scattered around 4.0, whereas the ones for SKYSHINE calculation were as large as 6.0. Calculational error was found to be reduced by adopting three-dimensional model based on the combinatorial geometry method. (author)

Development of fast ignition integrated interconnecting code (FI3) for fast ignition scheme

International Nuclear Information System (INIS)

Nagatomo, H.; Johzaki, T.; Mima, K.; Sunahara, A.; Nishihara, K.; Izawa, Y.; Sakagami, H.; Nakao, Y.; Yokota, T.; Taguchi, T.

2005-01-01

The numerical simulation plays an important role in estimating the feasibility and performance of the fast ignition. There are two key issues in numerical analysis for the fast ignition. One is the controlling the implosion dynamics to form a high density core plasma in non-spherical implosion, and the other is heating core plasma efficiency by the short pulse high intense laser. From initial laser irradiation to final fusion burning, all the physics are coupling strongly in any phase, and they must be solved consistently in computational simulation. However, in general, it is impossible to simulate laser plasma interaction and radiation hydrodynamics in a single computational code, without any numerical dissipation, special assumption or conditional treatment. Recently, we have developed 'Fast Ignition Integrated Interconnecting code' (FI 3 ) which consists of collective Particle-in-Cell code, Relativistic Fokker-Planck hydro code, and 2-dimensional radiation hydrodynamics code. And those codes are connecting with each other in data-flow bases. In this paper, we will present detail feature of the FI 3 code, and numerical results of whole process of fast ignition. (author)

Development of new two-dimensional spectral/spatial code based on dynamic cyclic shift code for OCDMA system

Science.gov (United States)

Jellali, Nabiha; Najjar, Monia; Ferchichi, Moez; Rezig, Houria

2017-07-01

In this paper, a new two-dimensional spectral/spatial codes family, named two dimensional dynamic cyclic shift codes (2D-DCS) is introduced. The 2D-DCS codes are derived from the dynamic cyclic shift code for the spectral and spatial coding. The proposed system can fully eliminate the multiple access interference (MAI) by using the MAI cancellation property. The effect of shot noise, phase-induced intensity noise and thermal noise are used to analyze the code performance. In comparison with existing two dimensional (2D) codes, such as 2D perfect difference (2D-PD), 2D Extended Enhanced Double Weight (2D-Extended-EDW) and 2D hybrid (2D-FCC/MDW) codes, the numerical results show that our proposed codes have the best performance. By keeping the same code length and increasing the spatial code, the performance of our 2D-DCS system is enhanced: it provides higher data rates while using lower transmitted power and a smaller spectral width.

Development of the Multi-Phase/Multi-Dimensional Code BUBBLEX

International Nuclear Information System (INIS)

Lee, Sang Yong; Kim, Shin Whan; Kim, Eun Kee

2005-01-01

A test version of the two-fluid program has been developed by extending the PISO algorithm. Unlike the conventional industry two-fluid codes, such as, RELAP5 and TRAC, this scheme does not need to develop a pressure matrix. Instead, it adopts the iterative procedure to implement the implicitness of the pressure. In this paper, a brief introduction to the numerical scheme will be presented. Then, its application to bubble column simulation will be described. Some concluding remarks will be followed

Development of a multi-dimensional realistic thermal-hydraulic system analysis code, MARS 1.3 and its verification

Energy Technology Data Exchange (ETDEWEB)

Lee, Won Jae; Chung, Bub Dong; Jeong, Jae Jun; Ha, Kwi Seok [Korea Atomic Energy Research Institute, Taejon (Korea)

1998-06-01

A multi-dimensional realistic thermal-hydraulic system analysis code, MARS version 1.3 has been developed. Main purpose of MARS 1.3 development is to have the realistic analysis capability of transient two-phase thermal-hydraulics of Pressurized Water Reactors (PWRs) especially during Large Break Loss of Coolant Accidents (LBLOCAs) where the multi-dimensional phenomena domain the transients. MARS code is a unified version of USNRC developed COBRA-TF, domain the transients. MARS code is a unified version of USNRC developed COBRA-TF, three-dimensional (3D) reactor vessel analysis code, and RELAP5/MOD3.2.1.2, one-dimensional (1D) reactor system analysis code., Developmental requirements for MARS are chosen not only to best utilize the existing capability of the codes but also to have the enhanced capability in code maintenance, user accessibility, user friendliness, code portability, code readability, and code flexibility. For the maintenance of existing codes capability and the enhancement of code maintenance capability, user accessibility and user friendliness, MARS has been unified to be a single code consisting of 1D module (RELAP5) and 3D module (COBRA-TF). This is realized by implicitly integrating the system pressure matrix equations of hydrodynamic models and solving them simultaneously, by modifying the 1D/3D calculation sequence operable under a single Central Processor Unit (CPU) and by unifying the input structure and the light water property routines of both modules. In addition, the code structure of 1D module is completely restructured using the modular data structure of standard FORTRAN 90, which greatly improves the code maintenance capability, readability and portability. For the code flexibility, a dynamic memory management scheme is applied in both modules. MARS 1.3 now runs on PC/Windows and HP/UNIX platforms having a single CPU, and users have the options to select the 3D module to model the 3D thermal-hydraulics in the reactor vessel or other

Development of a code of practice for deep geothermal wells

International Nuclear Information System (INIS)

Leaver, J.D.; Bolton, R.S.; Dench, N.D.; Fooks, L.

1990-01-01

Recent and on-going changes to the structure of the New Zealand geothermal industry has shifted responsibility for the development of geothermal resources from central government to private enterprise. The need for a code of practice for deep geothermal wells was identified by the Geothermal Inspectorate of the Ministry of Commerce to maintain adequate standards of health and safety and to assist with industry deregulation. This paper reports that the Code contains details of methods, procedures, formulae and design data necessary to attain those standards, and includes information which drilling engineers having experience only in the oil industry could not be expected to be familiar with

Development of health effect assessment software using MACCS2 code

International Nuclear Information System (INIS)

Hwang, Seok-Won; Park, Jong-Woon; Kang, Kyung Min; Jae, Moosung

2008-01-01

The extended regulatory interests in severe accidents management and enhanced safety regulatory requirements raise a need of more accurate analysis of the effect to the public health by users with diverse disciplines. This facilitates this work to develop web-based radiation health effect assessment software, RASUM, by using the MACCS2 code and HTML language to provide diverse users (regulators, operators, and public) with easy understanding, modeling, calculating, analyzing, documenting and reporting of the radiation health effect under hypothetical severe accidents. The engine of the web-based RASUM uses the MACCS2 as a base code developed by NRC and is composed of five modules such as development module, PSA training module, output module, input data module (source term, population distribution, meteorological data, etc.), and MACCS2 run module. For verification and demonstration of the RASUM, the offsite consequence analysis using the RASUM frame is performed for such as early fatality risk, organ does, and whole body does for two selected scenarios. Moreover, CCDF results from the RASUM for KSNP and CANDU type reactors are presented and compared. (author)

Development and Verification of Smoothed Particle Hydrodynamics Code for Analysis of Tsunami near NPP

Energy Technology Data Exchange (ETDEWEB)

Jo, Young Beom; Kim, Eung Soo [Seoul National Univ., Seoul (Korea, Republic of)

2014-10-15

It becomes more complicated when considering the shape and phase of the ground below the seawater. Therefore, some different attempts are required to precisely analyze the behavior of tsunami. This paper introduces an on-going activities on code development in SNU based on an unconventional mesh-free fluid analysis method called Smoothed Particle Hydrodynamics (SPH) and its verification work with some practice simulations. This paper summarizes the on-going development and verification activities on Lagrangian mesh-free SPH code in SNU. The newly developed code can cover equation of motions and heat conduction equation so far, and verification of each models is completed. In addition, parallel computation using GPU is now possible, and GUI is also prepared. If users change input geometry or input values, they can simulate for various conditions geometries. A SPH method has large advantages and potential in modeling of free surface, highly deformable geometry and multi-phase problems that traditional grid-based code has difficulties in analysis. Therefore, by incorporating more complex physical models such as turbulent flow, phase change, two-phase flow, and even solid mechanics, application of the current SPH code is expected to be much more extended including molten fuel behaviors in the sever accident.

Development of subchannel analysis code MATRA-LMR for KALIMER subassembly thermal-hydraulics

International Nuclear Information System (INIS)

Won-Seok Kim; Young-Gyun Kim

2000-01-01

In the sodium cooled liquid metal reactors, the design limit are imposed on the maximum temperatures of claddings and fuel pins. Thus an accurate prediction of core coolant/fuel temperature distribution is essential to the LMR core thermal-hydraulic design. The detailed subchannel thermal-hydraulic analysis code MATRA-LMR (Multichannel Analyzer for Steady States and Transients in Rod Arrays for Liquid Metal Reactors) is being developed for KALIMER core design and analysis, based on COBRA-IV-i and MATRA. The major modifications and improvements implemented into MATRA-LMR are as follows: a) nonuniform axial noding capability, b) sodium properties calculation subprogram, c) sodium coolant heat transfer correlations, and d) most recent pressure drop correlations, such as Novendstern, Chiu-Rohsenow-Todreas and Cheng-Todreas. To assess the development status of this code, the benchmark calculations were performed with the ORNL 19 pin tests and EBR-II seven-assembly SLTHEN calculation results. The calculation results of MATRA-LMR for ORNL 19-pin assembly tests and EBR-II 91-pin experiments were compared to the measurements, and to SABRE4 and SLTHEN code calculation results, respectively. In this comparison, the differences are found among the three codes because of the pressure drop and the thermal mixing modellings. Finally, the major technical results of the conceptual design for the KALIMER 98.03 core have been compared with the calculations of MATRA-LMR, SABRE4 and SLTHEN codes. (author)

The development of the fuel rod transient performance analysis code FTPAC

International Nuclear Information System (INIS)

Han Zhijie; Ji Songtao

2014-01-01

Fuel rod behavior, especially the integrity of cladding, played an important role in fuel safety research during reactor transient and hypothetical accidents conditions. In order to study fuel rod performance under transient accidents, FTPAC (Fuel Transient Performance Analysis Code) has been developed for simulating light water reactor fuel rod transient behavior when power or coolant boundary conditions are rapidly changing. It is composed of temperature, mechanical deformation, cladding oxidation and gas pressure model. The assessment was performed by comparing FTPAC code analysis result to experiments data and FRAPTRAN code calculations. Comparison shows that, the FTPAC gives reasonable agreement in temperature, deformation and gas pressure prediction. And the application of slip coefficient is more suitable for simulating the sliding between pellet and cladding when the gap is closed. (authors)

Development of the computer code for transient analysis in experimental fast reactor

International Nuclear Information System (INIS)

Moreira, M.L.; Sato, E.F.

1989-01-01

A calculational model of heat transfer and fluid coolant dynamics, for thermal-hydraulic simulation of the primary system components of a pool type experimental fast breeder reactor, has developed. Programmed in FORTRAN, the SORES code was used to simulate transients as loss of pumping and loss of secondary sodium flow in the EBRII. The SORES results compared with measured data and NATDEMO code results was found to be good. (author) [pt

Development of a ECOREA-II code for human exposures from radionuclides through food chain

International Nuclear Information System (INIS)

Yoo, D. H.; Choi, Y. H.

2001-01-01

The release of radionuclides from nuclear facilities following an accident into air results in human exposures through two pathways. One is direct human exposures by inhalation or dermal absorption of these radionucles. Another is indirect human exposures through food chain which includes intakes of plant products such as rice, vegetables from contaiminated soil and animal products such as meet, milk and eggs feeded by contaminated grasses or plants on the terrestial surface. This study presents efforts of the development of a computer code for the assessment of the indirect human exposure through such food chains. The purpose of ECOREA-II code is to develop appropriate models suitable for a specific soil condition in Korea based on previous experimental efforts and to provide a more user-friendly environment such as GUI for the use of the code. Therefore, the current code, when more fully developed, is expected to increase the understanding of environmental safety assessment of nuclear facilities following an accident and provide a reasonable regulatory guideline with respecte to food safety issues

Verification of WIMS-ANL to be used as supporting code for WIMS-CANDU development

Energy Technology Data Exchange (ETDEWEB)

Chung, Dai Hai; Kim, Won Young; Park, Joo Hwan

2007-08-15

The lattice code WIMS-ANL has been tested in order to assess it for the qualification to be used as a supporting code to aide the WIMS-CANDU development. A series of calculations have been performed to determine lattice physics parameters such as multiplication factors, isotopic number densities and coolant void reactivity. The WIMS-ANL results are compared with the predictions of WIMS-AECL/D4/D5 and PPV (POWDERPUFS-V), and the comparisons indicate that WIMS-ANL can be used not only as a supporting code to aide the WIMS-CANDU development, but also as a starting source for the study of developing detailed model that could delineate the realistic situations as it might occur during LOCA such as the asymmetric flux distribution across lattice cell.

Automatic coding method of the ACR Code

International Nuclear Information System (INIS)

Park, Kwi Ae; Ihm, Jong Sool; Ahn, Woo Hyun; Baik, Seung Kook; Choi, Han Yong; Kim, Bong Gi

1993-01-01

The authors developed a computer program for automatic coding of ACR(American College of Radiology) code. The automatic coding of the ACR code is essential for computerization of the data in the department of radiology. This program was written in foxbase language and has been used for automatic coding of diagnosis in the Department of Radiology, Wallace Memorial Baptist since May 1992. The ACR dictionary files consisted of 11 files, one for the organ code and the others for the pathology code. The organ code was obtained by typing organ name or code number itself among the upper and lower level codes of the selected one that were simultaneous displayed on the screen. According to the first number of the selected organ code, the corresponding pathology code file was chosen automatically. By the similar fashion of organ code selection, the proper pathologic dode was obtained. An example of obtained ACR code is '131.3661'. This procedure was reproducible regardless of the number of fields of data. Because this program was written in 'User's Defined Function' from, decoding of the stored ACR code was achieved by this same program and incorporation of this program into program in to another data processing was possible. This program had merits of simple operation, accurate and detail coding, and easy adjustment for another program. Therefore, this program can be used for automation of routine work in the department of radiology

Development of a 1D thermal-hydraulic analysis code for once-through steam generator in SMRs using straight tubes

Energy Technology Data Exchange (ETDEWEB)

Park, Youngjae; Kim, Iljin; Kim, Hyungdae [Kyung Hee University, Yongin (Korea, Republic of)

2015-10-15

Diverse integral/small-modular reactors (SMRs) have been developed. Once-through steam generator (OTSG) which generates superheated steam without steam separator and dryer was used in the SMRs to reduce volume of steam generator. It would be possible to design a new steam generator with best estimate thermal-hydraulic codes such as RELAP and MARS. However, it is not convenience to use the general purpose thermal-hydraulic analysis code to design a specific component of nuclear power plants. A widely used simulation tool for thermal-hydraulic analysis of drum-type steam generators is ATHOS, which allows 3D analysis. On the other hand, a simple 1D thermal-hydraulic analysis code might be accurate enough for the conceptual design of OTSG. In this study, thermal-hydraulic analysis code for conceptual design of OTSG was developed using 1D homogeneous equilibrium model (HEM). A benchmark calculation was also conducted to verify and validate the prediction accuracy of the developed code by comparing with the analysis results with MARS. Finally, conceptual design of OTSG was conducted by the developed code. A simple 1D thermal-hydraulic analysis code was developed for the purpose of conceptual design OTSG for SMRs. A set of benchmark calculations was conducted to verify and validate the analysis accuracy of the developed code by comparing results obtained with a best-estimated thermal-hydraulic analysis code, MARS. Finally, analysis of two different OTSG design concepts with superheating and recirculation was demonstrated using the developed code.

Development of Educational SharePoint portal for coding students

OpenAIRE

Colomer Castelló, Gerard

2016-01-01

The project will explain what is SharePoint, why is used and who does use it. It will also expose some alternatives, compare them to SharePoint and expose the pros and cons. The main objective of this project will be developing an educational SharePoint portal. Using this portal, coding students will be able to share their solutions to different exercises, vote the best solutions and comment them. This portal will be developed using only software and servers obtained legally without any cost....

Practical Salesforce.com development without code customizing salesforce on the Force.com platform

CERN Document Server

Weinmeister, Philip

2014-01-01

Are you facing a challenging Salesforce.com problem-say, relating to customization, configuration, reporting, dashboards, or formulation-that you can't quite crack? Or maybe you are hoping to infuse some creativity into your solution design strategy to solve problems faster or make solutions more efficient? Practical Salesforce.com Development Without Code shows you how to unlock the power of the Force.com platform to solve real business problems-and all without writing a line of code. Adhering to Salesforce.com's ""Clicks, not code"" mantra, Salesforce.com expert Phil Weinmeister walks you t

Development of 2D particle-in-cell code to simulate high current, low ...

Indian Academy of Sciences (India)

Abstract. A code for 2D space-charge dominated beam dynamics study in beam trans- port lines is developed. The code is used for particle-in-cell (PIC) simulation of z-uniform beam in a channel containing solenoids and drift space. It can also simulate a transport line where quadrupoles are used for focusing the beam.

Recent Developments of JAEA's Monte Carlo Code MVP for Reactor Physics Applications

Science.gov (United States)

Nagaya, Yasunobu; Okumura, Keisuke; Mori, Takamasa

2014-06-01

This paper describes the recent development status of a Monte Carlo code MVP developed at Japan Atomic Energy Agency. The basic features and capabilities of MVP are overviewed. In addition, new capabilities useful for reactor analysis are also described.

Development of TIGER code for radionuclide transport in a geochemically evolving region

International Nuclear Information System (INIS)

Mihara, Morihiro; Ooi, Takao

2004-01-01

In a transuranic (TRU) waste geological disposal facility, using cementitious materials is being considered. Cementitious materials will gradually dissolve in groundwater over the long-term. In the performance assessment report of a TRU waste repository in Japan already published, the most conservative radionuclide migration parameter set was selected considering the evolving cementitious material. Therefore, a tool to perform the calculation of radionuclide transport considering long-term geochemically evolving cementitious materials, named the TIGER code, Transport In Geochemically Evolving Region was developed to calculate a more realistic performance assessment. It can calculate radionuclide transport in engineered and natural barrier systems. In this report, mathematical equations of this code are described and validated with analytical solutions and results of other codes for radionuclide transport. The more realistic calculation of radionuclide transport for a TRU waste geological disposal system using the TIGER code could be performed. (author)

Discussion on LDPC Codes and Uplink Coding

Science.gov (United States)

Andrews, Ken; Divsalar, Dariush; Dolinar, Sam; Moision, Bruce; Hamkins, Jon; Pollara, Fabrizio

2007-01-01

This slide presentation reviews the progress that the workgroup on Low-Density Parity-Check (LDPC) for space link coding. The workgroup is tasked with developing and recommending new error correcting codes for near-Earth, Lunar, and deep space applications. Included in the presentation is a summary of the technical progress of the workgroup. Charts that show the LDPC decoder sensitivity to symbol scaling errors are reviewed, as well as a chart showing the performance of several frame synchronizer algorithms compared to that of some good codes and LDPC decoder tests at ESTL. Also reviewed is a study on Coding, Modulation, and Link Protocol (CMLP), and the recommended codes. A design for the Pseudo-Randomizer with LDPC Decoder and CRC is also reviewed. A chart that summarizes the three proposed coding systems is also presented.

Development of a computer program to support an efficient non-regression test of a thermal-hydraulic system code

Energy Technology Data Exchange (ETDEWEB)

Lee, Jun Yeob; Jeong, Jae Jun [School of Mechanical Engineering, Pusan National University, Busan (Korea, Republic of); Suh, Jae Seung [System Engineering and Technology Co., Daejeon (Korea, Republic of); Kim, Kyung Doo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-10-15

During the development process of a thermal-hydraulic system code, a non-regression test (NRT) must be performed repeatedly in order to prevent software regression. The NRT process, however, is time-consuming and labor-intensive. Thus, automation of this process is an ideal solution. In this study, we have developed a program to support an efficient NRT for the SPACE code and demonstrated its usability. This results in a high degree of efficiency for code development. The program was developed using the Visual Basic for Applications and designed so that it can be easily customized for the NRT of other computer codes.

Development of Transient-Reactor Analysis Code (TRAC) for real-time applications

International Nuclear Information System (INIS)

Niederauer, G.F.; Giguere, P.T.; Lime, J.F.; Knight, T.D.; Ashy, O.; Fakory, R.

1997-01-01

This is the final report of a six-month, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). Nuclear-plant training simulators employ simplified one-dimensional thermal-hydraulics codes because of the demands to run in real time and with limited computing power. The objective of this project was to investigate the feasibility of using the advanced Transient-Reactor Analysis Code (TRAC) in a simulator to increase the fidelity of a simulator. Many issues need to be addressed to take such a complex code from a batch engineering environment to a real-time environment. Working with simulator vendor, GSE, the authors investigated the technical issues relating to integrating TRAC into a real-time environment. They also modified a nuclear power plant model for simulator purposes and investigated its performance in real time

Development of an advanced fluid-dynamic analysis code: α-flow

International Nuclear Information System (INIS)

Akiyama, Mamoru

1990-01-01

A Project for development of large scale three-dimensional fluid-dynamic analysis code, α-FLOW, coping with the recent advancement of supercomputers and workstations, has been in progress. This project is called the α-Project, which has been promoted by the Association for Large Scale Fluid Dynamics Analysis Code comprising private companies and research institutions such as universities. The developmental period for the α-FLOW is four years, March 1989 to March 1992. To date, the major portions of basic design and program preparation have been completed and the project is in the stage of testing each module. In this paper, the present status of the α-Project, design policy and outline of α-FLOW are described. (author)

Development and feasibility testing of the Pediatric Emergency Discharge Interaction Coding Scheme.

Science.gov (United States)

Curran, Janet A; Taylor, Alexandra; Chorney, Jill; Porter, Stephen; Murphy, Andrea; MacPhee, Shannon; Bishop, Andrea; Haworth, Rebecca

2017-08-01

Discharge communication is an important aspect of high-quality emergency care. This study addresses the gap in knowledge on how to describe discharge communication in a paediatric emergency department (ED). The objective of this feasibility study was to develop and test a coding scheme to characterize discharge communication between health-care providers (HCPs) and caregivers who visit the ED with their children. The Pediatric Emergency Discharge Interaction Coding Scheme (PEDICS) and coding manual were developed following a review of the literature and an iterative refinement process involving HCP observations, inter-rater assessments and team consensus. The coding scheme was pilot-tested through observations of HCPs across a range of shifts in one urban paediatric ED. Overall, 329 patient observations were carried out across 50 observational shifts. Inter-rater reliability was evaluated in 16% of the observations. The final version of the PEDICS contained 41 communication elements. Kappa scores were greater than .60 for the majority of communication elements. The most frequently observed communication elements were under the Introduction node and the least frequently observed were under the Social Concerns node. HCPs initiated the majority of the communication. Pediatric Emergency Discharge Interaction Coding Scheme addresses an important gap in the discharge communication literature. The tool is useful for mapping patterns of discharge communication between HCPs and caregivers. Results from our pilot test identified deficits in specific areas of discharge communication that could impact adherence to discharge instructions. The PEDICS would benefit from further testing with a different sample of HCPs. © 2017 The Authors. Health Expectations Published by John Wiley & Sons Ltd.

Development of INCTAC code for analyzing criticality accident phenomena

International Nuclear Information System (INIS)

Mitake, Susumu; Hayashi, Yamato; Sakurai, Shungo

2003-01-01

Aiming at understanding nuclear transients and thermal- and hydraulic-phenomena of the criticality accident, a code named INCTAC has been newly developed at the Institute of Nuclear Safety. The code is applicable to the analysis of criticality accident transients of aqueous homogenous fuel solution system. Neutronic transient model is composed of equations for the kinetics and for the spatial distributions, which are deduced from the time dependent multi-group transport equations with the quasi steady state assumption. Thermal-hydraulic transient model is composed of a complete set of the mass, momentum and energy equations together with the two-phase flow assumptions. Validation tests of INCTAC were made using the data obtained at TRACY, a transient experiment criticality facility of JAERI. The calculated results with INCTAC showed a very good agreement with the experiment data, except a slight discrepancy of the time when the peak of reactor power was attained. But, the discrepancy was resolved with the use of an adequate model for movement and transfer of the void in the fuel solution mostly generated by radiolysis. With a simulation model for the transport of radioactive materials through ventilation systems to the environment, INCTAC will be used as an overall safety evaluation code of the criticality accident. (author)

Development of a general coupling interface for the fuel performance code TRANSURANUS – Tested with the reactor dynamics code DYN3D

International Nuclear Information System (INIS)

Holt, L.; Rohde, U.; Seidl, M.; Schubert, A.; Van Uffelen, P.; Macián-Juan, R.

2015-01-01

Highlights: • A general coupling interface was developed for couplings of the TRANSURANUS code. • With this new tool simplified fuel behavior models in codes can be replaced. • Applicable e.g. for several reactor types and from normal operation up to DBA. • The general coupling interface was applied to the reactor dynamics code DYN3D. • The new coupled code system DYN3D–TRANSURANUS was successfully tested for RIA. - Abstract: A general interface is presented for coupling the TRANSURANUS fuel performance code with thermal hydraulics system, sub-channel thermal hydraulics, computational fluid dynamics (CFD) or reactor dynamics codes. As first application the reactor dynamics code DYN3D was coupled at assembly level in order to describe the fuel behavior in more detail. In the coupling, DYN3D provides process time, time-dependent rod power and thermal hydraulics conditions to TRANSURANUS, which in case of the two-way coupling approach transfers parameters like fuel temperature and cladding temperature back to DYN3D. Results of the coupled code system are presented for the reactivity transient scenario, initiated by control rod ejection. More precisely, the two-way coupling approach systematically calculates higher maximum values for the node fuel enthalpy. These differences can be explained thanks to the greater detail in fuel behavior modeling. The numerical performance for DYN3D–TRANSURANUS was proved to be fast and stable. The coupled code system can therefore improve the assessment of safety criteria, at a reasonable computational cost

Development of disruption thermal analysis code DREAM

Energy Technology Data Exchange (ETDEWEB)

Yamazaki, Seiichiro; Kobayahsi, Takeshi [Kawasaki Heavy Industries Ltd., Kobe (Japan); Seki, Masahiro

1989-07-01

When a plasma disruption takes place in a tokamak type fusion reactor, plasma facing componenets such as first wall and divertor/limiter are subjected to a intensse heat load in a short duration. At the surface of the wall, temperature rapidly rises, and melting and evaporation occurs. It causes reduction of wall thickness and crack initiation/propagation. As lifetime of the components is significantly affected by them, the transient analysis in consideration of phase changes and radiation heat loss in required in the design of these components. This paper describes the computer code DREAM, developed to perform the disruption thermal analysis, taking phase changes and radiation into account. (author).

Development of disruption thermal analysis code DREAM

International Nuclear Information System (INIS)

Yamazaki, Seiichiro; Kobayahsi, Takeshi; Seki, Masahiro.

1989-01-01

When a plasma disruption takes place in a tokamak type fusion reactor, plasma facing componenets such as first wall and divertor/limiter are subjected to a intensse heat load in a short duration. At the surface of the wall, temperature rapidly rises, and melting and evaporation occurs. It causes reduction of wall thickness and crack initiation/propagation. As lifetime of the components is significantly affected by them, the transient analysis in consideration of phase changes and radiation heat loss in required in the design of these components. This paper describes the computer code DREAM, developed to perform the disruption thermal analysis, taking phase changes and radiation into account. (author)

Development of best estimate auditing code for CANDU thermal hydraulic safety analysis

Energy Technology Data Exchange (ETDEWEB)

Chung, B. D.; Lee, W. J.; Lim, H. S. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-04-15

The main purpose of this study is to develop a thermal hydraulic auditing code for the CANDU reactor, modifying the model of existing PWR auditing tool, i.e. RELAP5/MOD3. This scope of project is first step of the whole project, thus focus to the establishment of improvement area. The study was performed by reconsideration of the previous code assessment works and investigation of AECL design analysis tools. In order to identify the thermal hydraulic phenomena for events, the whole system of CANDU plant was divided into main functional systems and subcomponents. Each phenomena was addressed to the each subcomponent. FinaIly improvement areas of model development for auditing tool were established based on the identified phenomena.

Development of Learning Management in Moral Ethics and Code of Ethics of the Teaching Profession Course

Science.gov (United States)

Boonsong, S.; Siharak, S.; Srikanok, V.

2018-02-01

The purposes of this research were to develop the learning management, which was prepared for the enhancement of students’ Moral Ethics and Code of Ethics in Rajamangala University of Technology Thanyaburi (RMUTT). The contextual study and the ideas for learning management development was conducted by the document study, focus group method and content analysis from the document about moral ethics and code of ethics of the teaching profession concerning Graduate Diploma for Teaching Profession Program. The main tools of this research were the summarize papers and analyse papers. The results of development showed the learning management for the development of moral ethics and code of ethics of the teaching profession for Graduate Diploma for Teaching Profession students could promote desired moral ethics and code of ethics of the teaching profession character by the integrated learning techniques which consisted of Service Learning, Contract System, Value Clarification, Role Playing, and Concept Mapping. The learning management was presented in 3 steps.

Developing improved MD codes for understanding processive cellulases

International Nuclear Information System (INIS)

Crowley, M F; Nimlos, M R; Himmel, M E; Uberbacher, E C; Iii, C L Brooks; Walker, R C

2008-01-01

The mechanism of action of cellulose-degrading enzymes is illuminated through a multidisciplinary collaboration that uses molecular dynamics (MD) simulations and expands the capabilities of MD codes to allow simulations of enzymes and substrates on petascale computational facilities. There is a class of glycoside hydrolase enzymes called cellulases that are thought to decrystallize and processively depolymerize cellulose using biochemical processes that are largely not understood. Understanding the mechanisms involved and improving the efficiency of this hydrolysis process through computational models and protein engineering presents a compelling grand challenge. A detailed understanding of cellulose structure, dynamics and enzyme function at the molecular level is required to direct protein engineers to the right modifications or to understand if natural thermodynamic or kinetic limits are in play. Much can be learned about processivity by conducting carefully designed molecular dynamics (MD) simulations of the binding and catalytic domains of cellulases with various substrate configurations, solvation models and thermodynamic protocols. Most of these numerical experiments, however, will require significant modification of existing code and algorithms in order to efficiently use current (terascale) and future (petascale) hardware to the degree of parallelism necessary to simulate a system of the size proposed here. This work will develop MD codes that can efficiently use terascale and petascale systems, not just for simple classical MD simulations, but also for more advanced methods, including umbrella sampling with complex restraints and reaction coordinates, transition path sampling, steered molecular dynamics, and quantum mechanical/molecular mechanical simulations of systems the size of cellulose degrading enzymes acting on cellulose

Development of dynamic simulation code for fuel cycle of fusion reactor

International Nuclear Information System (INIS)

Aoki, Isao; Seki, Yasushi; Sasaki, Makoto; Shintani, Kiyonori; Kim, Yeong-Chan

1999-02-01

A dynamic simulation code for fuel cycle of a fusion experimental reactor has been developed. The code follows the fuel inventory change with time in the plasma chamber and the fuel cycle system during 2 days pulse operation cycles. The time dependence of the fuel inventory distribution is evaluated considering the fuel burn and exhaust in the plasma chamber, purification and supply functions. For each subsystem of the plasma chamber and the fuel cycle system, the fuel inventory equation is written based on the equation of state considering the fuel burn and the function of exhaust, purification, and supply. The processing constants of subsystem for steady states were taken from the values in the ITER Conceptual Design Activity (CDA) report. Using this code, the time dependence of the fuel supply and inventory depending on the burn state and subsystem processing functions are shown. (author)

Development and validation of the fast doppler broadening module coupled within RMC code

International Nuclear Information System (INIS)

Yu Jiankai; Liang Jin'gang; Yu Ganglin; Wang Kan

2015-01-01

It is one of the efficient approach to reduce the memory consumption in Monte Carlo based reactor physical simulations by using the On-the-fly Doppler broadening for temperature dependent nuclear cross sections. RXSP is a nuclear cross sections processing code being developed by REAL team in Department of Engineering Physics in Tsinghua University, which has an excellent performance in Doppler broadening the temperature dependent continuous energy neutron cross sections. To meet the dual requirements of both accuracy and efficiency during the Monte Carlo simulations with many materials and many temperatures in it, this work enables the capability of on-the-fly pre-Doppler broadening cross sections during the neutron transport by coupling the Fast Doppler Broaden module in RXSP code embedded in the RMC code also being developed by REAL team in Tsinghua University. Additionally, the original OpenMP-based parallelism has been successfully converted into the MPI-based framework, being fully compatible with neutron transport in RMC code, which has achieved a vast parallel efficiency improvement. This work also provides a flexible approach to solve Monte Carlo based full core depletion calculation with many temperatures feedback in many isotopes. (author)

Study on a new meteorological sampling scheme developed for the OSCAAR code system

International Nuclear Information System (INIS)

Liu Xinhe; Tomita, Kenichi; Homma, Toshimitsu

2002-03-01

One important step in Level-3 Probabilistic Safety Assessment is meteorological sequence sampling, on which the previous studies were mainly related to code systems using the straight-line plume model and more efforts are needed for those using the trajectory puff model such as the OSCAAR code system. This report describes the development of a new meteorological sampling scheme for the OSCAAR code system that explicitly considers population distribution. A group of principles set for the development of this new sampling scheme includes completeness, appropriate stratification, optimum allocation, practicability and so on. In this report, discussions are made about the procedures of the new sampling scheme and its application. The calculation results illustrate that although it is quite difficult to optimize stratification of meteorological sequences based on a few environmental parameters the new scheme do gather the most inverse conditions in a single subset of meteorological sequences. The size of this subset may be as small as a few dozens, so that the tail of a complementary cumulative distribution function is possible to remain relatively static in different trials of the probabilistic consequence assessment code. (author)

The role of the PIRT process in identifying code improvements and executing code development

International Nuclear Information System (INIS)

Wilson, G.E.; Boyack, B.E.

1997-01-01

In September 1988, the USNRC issued a revised ECCS rule for light water reactors that allows, as an option, the use of best estimate (BE) plus uncertainty methods in safety analysis. The key feature of this licensing option relates to quantification of the uncertainty in the determination that an NPP has a low probability of violating the safety criteria specified in 10 CFR 50. To support the 1988 licensing revision, the USNRC and its contractors developed the CSAU evaluation methodology to demonstrate the feasibility of the BE plus uncertainty approach. The PIRT process, Step 3 in the CSAU methodology, was originally formulated to support the BE plus uncertainty licensing option as executed in the CSAU approach to safety analysis. Subsequent work has shown the PIRT process to be a much more powerful tool than conceived in its original form. Through further development and application, the PIRT process has shown itself to be a robust means to establish safety analysis computer code phenomenological requirements in their order of importance to such analyses. Used early in research directed toward these objectives, PIRT results also provide the technical basis and cost effective organization for new experimental programs needed to improve the safety analysis codes for new applications. The primary purpose of this paper is to describe the generic PIRT process, including typical and common illustrations from prior applications. The secondary objective is to provide guidance to future applications of the process to help them focus, in a graded approach, on systems, components, processes and phenomena that have been common in several prior applications

Deciphering the genetic regulatory code using an inverse error control coding framework.

Energy Technology Data Exchange (ETDEWEB)

Rintoul, Mark Daniel; May, Elebeoba Eni; Brown, William Michael; Johnston, Anna Marie; Watson, Jean-Paul

2005-03-01

We have found that developing a computational framework for reconstructing error control codes for engineered data and ultimately for deciphering genetic regulatory coding sequences is a challenging and uncharted area that will require advances in computational technology for exact solutions. Although exact solutions are desired, computational approaches that yield plausible solutions would be considered sufficient as a proof of concept to the feasibility of reverse engineering error control codes and the possibility of developing a quantitative model for understanding and engineering genetic regulation. Such evidence would help move the idea of reconstructing error control codes for engineered and biological systems from the high risk high payoff realm into the highly probable high payoff domain. Additionally this work will impact biological sensor development and the ability to model and ultimately develop defense mechanisms against bioagents that can be engineered to cause catastrophic damage. Understanding how biological organisms are able to communicate their genetic message efficiently in the presence of noise can improve our current communication protocols, a continuing research interest. Towards this end, project goals include: (1) Develop parameter estimation methods for n for block codes and for n, k, and m for convolutional codes. Use methods to determine error control (EC) code parameters for gene regulatory sequence. (2) Develop an evolutionary computing computational framework for near-optimal solutions to the algebraic code reconstruction problem. Method will be tested on engineered and biological sequences.

Development and Application of a Plant Code to the Analysis of Transients in Integrated Reactors

International Nuclear Information System (INIS)

Rabiti, A.; Gimenez, M.; Delmastro, D.; Zanocco, P.

2003-01-01

In this work, a secondary system model for a CAREM-25 type nuclear power plant was developed.A two-phase flow homogenous model was used and found adequate for the scope of the present work.A finite difference scheme was used for the numerical implementation of the model.This model was coupled to the HUARPE code, a primary circuit code, in order to obtain a plant code.This plant code was used to analyze the inherent response of the system, without control feedback loops, for a transient of steam generator feed-water mass flow reduction.The results obtained are satisfactory, but a validation against other plant codes is still necessary

Present capabilities and new developments in antenna modeling with the numerical electromagnetics code NEC

Energy Technology Data Exchange (ETDEWEB)

Burke, G.J.

1988-04-08

Computer modeling of antennas, since its start in the late 1960's, has become a powerful and widely used tool for antenna design. Computer codes have been developed based on the Method-of-Moments, Geometrical Theory of Diffraction, or integration of Maxwell's equations. Of such tools, the Numerical Electromagnetics Code-Method of Moments (NEC) has become one of the most widely used codes for modeling resonant sized antennas. There are several reasons for this including the systematic updating and extension of its capabilities, extensive user-oriented documentation and accessibility of its developers for user assistance. The result is that there are estimated to be several hundred users of various versions of NEC world wide. 23 refs., 10 figs.

Vector Network Coding

OpenAIRE

Ebrahimi, Javad; Fragouli, Christina

2010-01-01

We develop new algebraic algorithms for scalar and vector network coding. In vector network coding, the source multicasts information by transmitting vectors of length L, while intermediate nodes process and combine their incoming packets by multiplying them with L X L coding matrices that play a similar role as coding coefficients in scalar coding. Our algorithms for scalar network jointly optimize the employed field size while selecting the coding coefficients. Similarly, for vector co...

Development and preliminary validation of flux map processing code MAPLE

International Nuclear Information System (INIS)

Li Wenhuai; Zhang Xiangju; Dang Zhen; Chen Ming'an; Lu Haoliang; Li Jinggang; Wu Yuanbao

2013-01-01

The self-reliant flux map processing code MAPLE was developed by China General Nuclear Power Corporation (CGN). Weight coefficient method (WCM), polynomial expand method (PEM) and thin plane spline (TPS) method were applied to fit the deviation between measured and predicted detector signal results for two-dimensional radial plane, to interpolate or extrapolate the non-instrumented location deviation. Comparison of results in the test cases shows that the TPS method can better capture the information of curved fitting lines than the other methods. The measured flux map data of the Lingao Nuclear Power Plant were processed using MAPLE as validation test cases, combined with SMART code. Validation results show that the calculation results of MAPLE are reasonable and satisfied. (authors)

Description of computer code PRINS, Program for Interpreting Gamma Spectra, developed at ENEA

Energy Technology Data Exchange (ETDEWEB)

Borsari, R. [ENEA, Centro Ricerche `E. Clementel`, Bologna (Italy). Dip. Energia

1995-11-01

The computer code PRINS, program for interpreting gamma Spectra, has been developed in collaboration with CENG/SECC (Centre Etude Nucleaire Grenoble / Service Etude Comportement du Combustible). Later it has been updated and improved at ENEA. Properties of the PRINS code are: (1) A powerful algorithm to locate the peaks; (2) An accurate evaluation of the errors; (3) Possibility of an automatic channels-energy calibration.

Description of computer code PRINS, Program for Interpreting Gamma Spectra, developed at ENEA

International Nuclear Information System (INIS)

Borsari, R.

1995-12-01

The computer code PRINS, PRogram for INterpreting gamma Spectra, has been developed in collaboration with CENG/SECC (Centre Etude Nucleaire Grenoble / Service Etude Comportement du Combustible). Later it has been updated and improved at ENEA. Properties of the PRINS code are: I) A powerful algorithm to locate the peaks; 2) An accurate evaluation of the errors; 3) Possibility of an automatic channels-energy calibration

Development of multi-group spectral code TVS-M

International Nuclear Information System (INIS)

Lazarenko, A. P.; Pryanichnikov, A. V.; Kalugin, M. A.; Gurevich, M. I.

2011-01-01

This paper is dedicated to the latest version of TVS-M code - TVS-M 2007, which allows the neutron flux distribution inside fuel assemblies to be calculated without using the diffusion approximation. The new spatial calculation module PERST introduced in TBS-M code is based on the first collisions probability method and allows the scattering anisotropy to be accounted for. This paper presents some preliminary results calculated with the use of the new version of TVS-M code. (Authors)

Development of sub-channel/system coupled code and its application to a supercritical water-cooled test loop

International Nuclear Information System (INIS)

Liu, X.J.; Yang, T.; Cheng, X.

2014-01-01

To analyze the local thermal-hydraulic parameters in the supercritical water reactor-fuel qualification test (SCWR-FQT) fuel bundle with a flow blockage, a coupled sub-channel and system code system is developed in this paper. Both of the sub-channel code and system code are adapted to transient analysis of SCWR. Two codes are coupled by data transfer and data adaptation at the interface. In the coupled code, the whole system behavior including safety system characteristic is analyzed by system code ATHLET-SC, whereas the local thermal-hydraulic parameters are predicted by the sub-channel code COBRA-SC. Sensitivity analysis are carried out respectively in ATHLET-SC and COBRA-SC code, to identify the appropriate models for description of the flow blockage phenomenon in the test loop. Some measures to mitigate the accident consequence are also trialed to demonstrate their effectiveness. The results indicate that the new developed code has good feasibility to transient analysis of supercritical water-cooled test. And the peak cladding temperature caused by blockage in the fuel assembly can be reduced effectively by the safety measures of SCWR-FQT. (author)

TASS code topical report. V.1 TASS code technical manual

International Nuclear Information System (INIS)

Sim, Suk K.; Chang, W. P.; Kim, K. D.; Kim, H. C.; Yoon, H. Y.

1997-02-01

TASS 1.0 code has been developed at KAERI for the initial and reload non-LOCA safety analysis for the operating PWRs as well as the PWRs under construction in Korea. TASS code will replace various vendor's non-LOCA safety analysis codes currently used for the Westinghouse and ABB-CE type PWRs in Korea. This can be achieved through TASS code input modifications specific to each reactor type. The TASS code can be run interactively through the keyboard operation. A simimodular configuration used in developing the TASS code enables the user easily implement new models. TASS code has been programmed using FORTRAN77 which makes it easy to install and port for different computer environments. The TASS code can be utilized for the steady state simulation as well as the non-LOCA transient simulations such as power excursions, reactor coolant pump trips, load rejections, loss of feedwater, steam line breaks, steam generator tube ruptures, rod withdrawal and drop, and anticipated transients without scram (ATWS). The malfunctions of the control systems, components, operator actions and the transients caused by the malfunctions can be easily simulated using the TASS code. This technical report describes the TASS 1.0 code models including reactor thermal hydraulic, reactor core and control models. This TASS code models including reactor thermal hydraulic, reactor core and control models. This TASS code technical manual has been prepared as a part of the TASS code manual which includes TASS code user's manual and TASS code validation report, and will be submitted to the regulatory body as a TASS code topical report for a licensing non-LOCA safety analysis for the Westinghouse and ABB-CE type PWRs operating and under construction in Korea. (author). 42 refs., 29 tabs., 32 figs

Development of flow network analysis code for block type VHTR core by linear theory method

International Nuclear Information System (INIS)

Lee, J. H.; Yoon, S. J.; Park, J. W.; Park, G. C.

2012-01-01

VHTR (Very High Temperature Reactor) is high-efficiency nuclear reactor which is capable of generating hydrogen with high temperature of coolant. PMR (Prismatic Modular Reactor) type reactor consists of hexagonal prismatic fuel blocks and reflector blocks. The flow paths in the prismatic VHTR core consist of coolant holes, bypass gaps and cross gaps. Complicated flow paths are formed in the core since the coolant holes and bypass gap are connected by the cross gap. Distributed coolant was mixed in the core through the cross gap so that the flow characteristics could not be modeled as a simple parallel pipe system. It requires lot of effort and takes very long time to analyze the core flow with CFD analysis. Hence, it is important to develop the code for VHTR core flow which can predict the core flow distribution fast and accurate. In this study, steady state flow network analysis code is developed using flow network algorithm. Developed flow network analysis code was named as FLASH code and it was validated with the experimental data and CFD simulation results. (authors)

The FELIX program of experiments and code development

International Nuclear Information System (INIS)

Turner, L.R.

1983-01-01

An experimental program and test bed called FELIX (Fusion Electromagnetic Induction Experiment) which is under construction at Argonne National Laboratory is described. The facility includes the following facilities; (a) a sizable constant field, analogous to a tokamak toroidal field or the confining field of a mirror reactor, (b) a pulsed field with a sizable rate of change, analogous to a pulsed poloidal field or to the changing field of a plasma disruption, perpendicular to the constant field, and (c) a sufficiently large volume to assure that large, complex test pieces can be tested, and that the forces, torques, currents, and field distortions which are developed are large enough to be measured accurately. The development of the necessary computer codes and the experimental program are examined. (U.K.)

ASTEC V2. Overview of code development and application at GRS

International Nuclear Information System (INIS)

Reinke, N.; Nowack, H.; Sonnenkalb, M.

2011-01-01

The integral code ASTEC (Accident Source Term Evaluation Code) commonly developed since 1996 by the French IRSN and the German GRS is a fast running programme, which allows the calculation of entire sequences of severe accidents (SA) in light water reactors from the initiating event up to the release of fission products into the environment, thereby covering all important in-vessel and containment phenomena. Thus, the main ASTEC application fields are intended to be accident sequence studies, uncertainty and sensitivity studies, probabilistic safety analysis level 2 as well as support to experiments. The modular structure of ASTEC allows running each module independently and separately, e.g. for separate effects analyses as well as a combination of multiple modules for coupled effects testing and integral analyses. Subject of this paper is an overview of the new V2 series of the ASTEC code system and presentation of exemplary results for the application to severe accidents sequences at PWRs. (orig.)

Building energy, building leadership : recommendations for the adoption, development, and implementation of a commercial building energy code in Manitoba

Energy Technology Data Exchange (ETDEWEB)

Akerstream, T. [Manitoba Hydro, Winnipeg, MB (Canada); Allard, K. [City of Thompson, Thompson, MB (Canada); Anderson, N.; Beacham, D. [Manitoba Office of the Fire Commissioner, Winnipeg, MB (Canada); Andrich, R. [The Forks North Portage Partnership, MB (Canada); Auger, A. [Natural Resources Canada, Ottawa, ON (Canada). Office of Energy Efficiency; Downs, R.G. [Shindico Realty Inc., Winnipeg, MB (Canada); Eastwood, R. [Number Ten Architectural Group, Winnipeg, MB (Canada); Hewitt, C. [SMS Engineering Ltd., Winnipeg, MB (Canada); Joshi, D. [City of Winnipeg, Winnipeg, MB (Canada); Klassen, K. [Manitoba Dept. of Energy Science and Technology, Winnipeg, MB (Canada); Phillips, B. [Unies Ltd., Winnipeg, MB (Canada); Wiebe, R. [Ben Wiebe Construction Ltd., Winnipeg, MB (Canada); Woelk, D. [Bockstael Construction Ltd., Winnipeg, MB (Canada); Ziemski, S. [CREIT Management LLP, Winnipeg, MB (Canada)

2006-09-15

This report presented a strategy and a set of recommendations for the adoption, development and implementation of an energy code for new commercial construction in Manitoba. The report was compiled by an advisory committee comprised of industry representatives and government agency representatives. Recommendations were divided into 4 categories: (1) advisory committee recommendations; (2) code adoption recommendations; (3) code development recommendations; and (4) code implementation recommendations. It was suggested that Manitoba should adopt an amended version of the Model National Energy Code for Buildings (1997) as a regulation under the Buildings and Mobile Homes Act. Participation in a national initiative to update the Model National Energy Code for Buildings was also advised. It was suggested that the energy code should be considered as the first step in a longer-term process towards a sustainable commercial building code. However, the code should be adopted within the context of a complete market transformation approach. Other recommendations included: the establishment of a multi-stakeholder energy code task group; the provision of information and technical resources to help build industry capacity; the establishment of a process for energy code compliance; and an ongoing review of the energy code to assess impacts and progress. Supplemental recommendations for future discussion included the need for integrated design by building design teams in Manitoba; the development of a program to provide technical assistance to building design teams; and collaboration between post-secondary institutions to develop and deliver courses on integrated building design to students and professionals. 17 refs.

Development of a detailed core flow analysis code for prismatic fuel reactors

International Nuclear Information System (INIS)

Bennett, R.G.

1990-01-01

The development of a computer code for the analysis of the detailed flow of helium in prismatic fuel reactors is reported. The code, called BYPASS, solves, a finite difference control volume formulation of the compressible, steady state fluid flow in highly cross-connected flow paths typical of the Modular High-Temperature Gas Cooled Reactor (MHTGR). The discretization of the flow in a core region typically considers the main coolant flow paths, the bypass gap flow paths, and the crossflow connections between them. 16 refs., 5 figs

Development of a computer code for thermohydraulic analysis of a heated channel in transients

International Nuclear Information System (INIS)

Jafari, J.; Kazeminejad, H.; Davilu, H.

2004-01-01

This paper discusses the thermohydraulic analysis of a heated channel of a nuclear reactor in transients by a computer code that has been developed by the writer. The considered geometry is a channel of a nuclear reactor with cylindrical or planar fuel rods. The coolant is water and flows from the outer surface of the fuel rod. To model the heat transfer in the fuel rod, two dimensional time dependent conduction equations has been solved by combination of numerical methods, O rthogonal Collocation Method in radial direction and finite difference method in axial direction . For coolant modelling the single phase time dependent energy equation has been used and solved by finite difference method . The combination of the first module that solves the conduction in the fuel rod and a second one that solved the energy balance in the coolant region constitute the computer code (Thyc-1) to analysis thermohydraulic of a heated channel in transients. The Orthogonal collocation method maintains the accuracy and computing time of conventional finite difference methods, while the computer storage is reduced by a factor of two. The same problem has been modelled by RELAP5/M3 system code to asses the validity of the Thyc-1 code. The good agreement of the results qualifies the developed code

Development and Verification of Tritium Analyses Code for a Very High Temperature Reactor

International Nuclear Information System (INIS)

Oh, Chang H.; Kim, Eung S.

2009-01-01

A tritium permeation analyses code (TPAC) has been developed by Idaho National Laboratory for the purpose of analyzing tritium distributions in the VHTR systems including integrated hydrogen production systems. A MATLAB SIMULINK software package was used for development of the code. The TPAC is based on the mass balance equations of tritium-containing species and a various form of hydrogen (i.e., HT, H2, HTO, HTSO4, and TI) coupled with a variety of tritium source, sink, and permeation models. In the TPAC, ternary fission and neutron reactions with 6Li, 7Li 10B, 3He were taken into considerations as tritium sources. Purification and leakage models were implemented as main tritium sinks. Permeation of HT and H2 through pipes, vessels, and heat exchangers were importantly considered as main tritium transport paths. In addition, electrolyzer and isotope exchange models were developed for analyzing hydrogen production systems including both high-temperature electrolysis and sulfur-iodine process. The TPAC has unlimited flexibility for the system configurations, and provides easy drag-and-drops for making models by adopting a graphical user interface. Verification of the code has been performed by comparisons with the analytical solutions and the experimental data based on the Peach Bottom reactor design. The preliminary results calculated with a former tritium analyses code, THYTAN which was developed in Japan and adopted by Japan Atomic Energy Agency were also compared with the TPAC solutions. This report contains descriptions of the basic tritium pathways, theory, simple user guide, verifications, sensitivity studies, sample cases, and code tutorials. Tritium behaviors in a very high temperature reactor/high temperature steam electrolysis system have been analyzed by the TPAC based on the reference indirect parallel configuration proposed by Oh et al. (2007). This analysis showed that only 0.4% of tritium released from the core is transferred to the product hydrogen

Research on the improvement of nuclear safety -The development of a severe accident analysis code-

International Nuclear Information System (INIS)

Kim, Heui Dong; Cho, Sung Won; Park, Jong Hwa; Hong, Sung Wan; Yoo, Dong Han; Hwang, Moon Kyoo; Noh, Kee Man; Song, Yong Man

1995-07-01

For prevention and mitigation of the containment failure during severe accident, the study is focused on the severe accident phenomena, especially, the ones occurring inside the cavity and is intended to improve existing models and develop analytical tools for the assessment of severe accidents. A correlation equation of the flame velocity of pre mixture gas of H 2 /air/steam has been suggested and combustion flame characteristic was analyzed using a developed computer code. For the analysis of the expansion phase of vapor explosion, the mechanical model has been developed. The development of a debris entrainment model in a reactor cavity with captured volume has been continued to review and examine the limitation and deficiencies of the existing models. Pre-test calculation was performed to support the severe accident experiment for molten corium concrete interaction study and the crust formation process and heat transfer characteristics of the crust have been carried out. A stress analysis code was developed using finite element method for the reactor vessel lower head failure analysis. Through international program of PHEBUS-FP and participation in the software development, the research on the core degradation process and fission products release and transportation are undergoing. CONTAIN and MELCOR codes were continuously updated under the cooperation with USNRC and French developed computer codes such as ICARE2, ESCADRE, SOPHAEROS were also installed into the SUN workstation. 204 figs, 61 tabs, 87 refs. (Author)

The FLUKA Code: Developments and Challenges for High Energy and Medical Applications

CERN Document Server

Böhlen, T T; Chin, M P W; Fassò, A; Ferrari, A; Ortega, P G; Mairani, A; Sala, P R; Smirnov, G; Vlachoudis, V

2014-01-01

The FLUKA Monte Carlo code is used extensively at CERN for all beam-machine interactions, radioprotection calculations and facility design of forthcoming projects. Such needs require the code to be consistently reliable over the entire energy range (from MeV to TeV) for all projectiles (full suite of elementary particles and heavy ions). Outside CERN, among various applications worldwide, FLUKA serves as a core tool for the HIT and CNAO hadron-therapy facilities in Europe. Therefore, medical applications further impose stringent requirements in terms of reliability and predictive power, which demands constant refinement of sophisticated nuclear models and continuous code improvement. Some of the latest developments implemented in FLUKA are presented in this paper, with particular emphasis on issues and concerns pertaining to CERN and medical applications.

Developing a Coding Scheme to Analyse Creativity in Highly-constrained Design Activities

DEFF Research Database (Denmark)

Dekoninck, Elies; Yue, Huang; Howard, Thomas J.

2010-01-01

This work is part of a larger project which aims to investigate the nature of creativity and the effectiveness of creativity tools in highly-constrained design tasks. This paper presents the research where a coding scheme was developed and tested with a designer-researcher who conducted two rounds...... of design and analysis on a highly constrained design task. This paper shows how design changes can be coded using a scheme based on creative ‘modes of change’. The coding scheme can show the way a designer moves around the design space, and particularly the strategies that are used by a creative designer...... larger study with more designers working on different types of highly-constrained design task is needed, in order to draw conclusions on the modes of change and their relationship to creativity....

Development of a perturbation code, PERT-K, for hexagonal core geometry

Energy Technology Data Exchange (ETDEWEB)

Kim, Taek Kyum; Kim, Sang Ji; Song, Hoon; Kim, Young Il; Kim, Young Jin [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-01-01

A perturbation code for hexagonal core geometry has been developed based on Nodal Expansion Method. By using relevant output files of DIF3D code, it can calculate the reactivity changes caused by perturbation in composition or/and neutron cross section libraries. The accuracy of PERT-K code has been validated by calculating the reactivity changes due to fuel composition change, the sodium void coefficients, and the sample reactivity worths of BFS-73-1 critical experiments. In the case of 10% reduction in all fuel isotopics at a assembly located in the outer core, PERT-K computation agrees with the direct computation by DIF3D within 60 pcm. The sample reactivity worths of BFS-73-1 critical experiments are predicted with PERT-K code within the experimental error bounds. For 100% sodium void occurrence at the inner core, the maximum difference of reactivity changes between PERT-K and direct DIF3D computations is less than 40 pcm. On the other hand, the same sodium void condition at the outer core leads to a difference of reactivity change greater than 400 pcm. However, as sodium voiding becomes near zero value, the difference becomes less and rapidly falls within the acceptable bound, i.e. 40 pcm. (author). 11 refs., 9 figs., 6 tabs.