WorldWideScience

Sample records for solutions technical progress

  1. Technical progress report

    International Nuclear Information System (INIS)

    1996-01-01

    This report summarizes experimental and theoretical work in basic nuclear physics carried out between October 1, 1995, the closing of our last Progress Report, and September 30, 1996 at the Nuclear Physics Laboratory of the University of Colorado, Boulder, under contracts DE-FG03-93ER-40774 and DE-FG03-95ER-40913 with the United States Department of Energy. The experimental contract supports broadly-based experimental research in intermediate energy nuclear physics. This report includes results from studies of Elementary Systems involving the study of the structure of the nucleon via polarized high-energy positron scattering (the HERMES experiment) and lower energy pion scattering from both polarized and unpolarized nucleon targets. Results from pion- and kaon-induced reactions in a variety of nuclear systems are reported under the section heading Meson Reactions; the impact of these and other results on understanding the nucleus is presented in the Nuclear Structure section. In addition, new results from scattering of high-energy electrons (from CEBAF/TJNAF) and pions (from KEK) from a broad range of nuclei are reported in the section on Incoherent Reactions. Finally, the development and performance of detectors produced by the laboratory are described in the section titled Instrumentation

  2. Technical progress and climatic change

    International Nuclear Information System (INIS)

    Ausubel, J.H.

    1995-01-01

    The global warming debate has neglected and thus underestimated the importance of technical change in considering reduction in greenhouse gases and adaptation to climate change. Relevant quantitative cases of long-run technical change during the past 100 years are presented in computing, communications, transport, energy, and agriculture. A noteworthy technological trajectory is that of decarbonization, or decreasing carbon intensity of primary energy. If human societies have not yet reached the end of the history of technology, the cost structure for mitigation and adaptation changes could be cheap. (Author)

  3. Progress report : Technical Physics Division

    International Nuclear Information System (INIS)

    Gopalaraman, C.P.; Deshpande, R.Y.

    1978-01-01

    The research and development work carried out in the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, is reported. Some of the achievements are: (1) fabrication of mass spectrometers for heavy water analysis and lithium 6/7 isotope ratio measurement, (2) fabrication of electronic components for mass spectrometers, (3) growing of sodium iodide crystals for radiation detectors, (4) development of sandwich detectors comprising of NaI(Tl) and CaI(Na), (5) fabrication of mass spectrometer type leak detectors and (6) fabrication of the high vacuum components of the vacuum system of the variable energy cyclotron based at Calcutta. (M.G.B.)

  4. Technical solutions to nonproliferation challenges

    Energy Technology Data Exchange (ETDEWEB)

    Satkowiak, Lawrence [Director, Nonproliferation, Safeguards and Security Programs, Oak Ridge National Laboratory, Oak Ridge, Tennessee (United States)

    2014-05-09

    The threat of nuclear terrorism is real and poses a significant challenge to both U.S. and global security. For terrorists, the challenge is not so much the actual design of an improvised nuclear device (IND) but more the acquisition of the special nuclear material (SNM), either highly enriched uranium (HEU) or plutonium, to make the fission weapon. This paper provides two examples of technical solutions that were developed in support of the nonproliferation objective of reducing the opportunity for acquisition of HEU. The first example reviews technologies used to monitor centrifuge enrichment plants to determine if there is any diversion of uranium materials or misuse of facilities to produce undeclared product. The discussion begins with a brief overview of the basics of uranium processing and enrichment. The role of the International Atomic Energy Agency (IAEA), its safeguard objectives and how the technology evolved to meet those objectives will be described. The second example focuses on technologies developed and deployed to monitor the blend down of 500 metric tons of HEU from Russia's dismantled nuclear weapons to reactor fuel or low enriched uranium (LEU) under the U.S.-Russia HEU Purchase Agreement. This reactor fuel was then purchased by U.S. fuel fabricators and provided about half the fuel for the domestic power reactors. The Department of Energy established the HEU Transparency Program to provide confidence that weapons usable HEU was being blended down and thus removed from any potential theft scenario. Two measurement technologies, an enrichment meter and a flow monitor, were combined into an automated blend down monitoring system (BDMS) and were deployed to four sites in Russia to provide 24/7 monitoring of the blend down. Data was downloaded and analyzed periodically by inspectors to provide the assurances required.

  5. Technical solutions to nonproliferation challenges

    Science.gov (United States)

    Satkowiak, Lawrence

    2014-05-01

    The threat of nuclear terrorism is real and poses a significant challenge to both U.S. and global security. For terrorists, the challenge is not so much the actual design of an improvised nuclear device (IND) but more the acquisition of the special nuclear material (SNM), either highly enriched uranium (HEU) or plutonium, to make the fission weapon. This paper provides two examples of technical solutions that were developed in support of the nonproliferation objective of reducing the opportunity for acquisition of HEU. The first example reviews technologies used to monitor centrifuge enrichment plants to determine if there is any diversion of uranium materials or misuse of facilities to produce undeclared product. The discussion begins with a brief overview of the basics of uranium processing and enrichment. The role of the International Atomic Energy Agency (IAEA), its safeguard objectives and how the technology evolved to meet those objectives will be described. The second example focuses on technologies developed and deployed to monitor the blend down of 500 metric tons of HEU from Russia's dismantled nuclear weapons to reactor fuel or low enriched uranium (LEU) under the U.S.-Russia HEU Purchase Agreement. This reactor fuel was then purchased by U.S. fuel fabricators and provided about half the fuel for the domestic power reactors. The Department of Energy established the HEU Transparency Program to provide confidence that weapons usable HEU was being blended down and thus removed from any potential theft scenario. Two measurement technologies, an enrichment meter and a flow monitor, were combined into an automated blend down monitoring system (BDMS) and were deployed to four sites in Russia to provide 24/7 monitoring of the blend down. Data was downloaded and analyzed periodically by inspectors to provide the assurances required.

  6. 48 CFR 2052.211-71 - Technical progress report.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Technical progress report... Technical progress report. As prescribed at 2011.104-70(b), the contracting officer shall insert the... solicitation. Technical Progress Report (JAN 1993) The contractor shall provide a monthly Technical Progress...

  7. IRIS Final Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    M. D. Carelli

    2003-11-03

    OAK-B135 This NERI project, originally started as the Secure Transportable Autonomous Light Water Reactor (STAR-LW) and currently known as the International Reactor Innovative and Secure (IRIS) project, had the objective of investigating a novel type of water-cooled reactor to satisfy the Generation IV goals: fuel cycle sustainability, enhanced reliability and safety, and improved economics. The research objectives over the three-year (1999-2002) program were as follows: First year: Assess various design alternatives and establish main characteristics of a point design; Second year: Perform feasibility and engineering assessment of the selected design solutions; Third year: Complete reactor design and performance evaluation, including cost assessment These objectives were fully attained and actually they served to launch IRIS as a full fledged project for eventual commercial deployment. The program did not terminate in 2002 at the end of the NERI program, and has just entered in its fifth year. This has been made possible by the IRIS project participants which have grown from the original four member, two-countries team to the current twenty members, nine countries consortium. All the consortium members work under their own funding and it is estimated that the value of their in-kind contributions over the life of the project has been of the order of $30M. Currently, approximately 100 people worldwide are involved in the project. A very important constituency of the IRIS project is the academia: 7 universities from four countries are members of the consortium and five more US universities are associated via parallel NERI programs. To date, 97 students have worked or are working on IRIS; 59 IRIS-related graduate theses have been prepared or are in preparation, and 41 of these students have already graduated with M.S. (33) or Ph.D. (8) degrees. This ''final'' report (final only as far as the NERI program is concerned) summarizes the work performed

  8. Technical progress and its strategic consequences

    International Nuclear Information System (INIS)

    Bouchard, G.

    1999-01-01

    The history of energy during recent decades has shown that technical progress can have consequences for the organisation of markets, company strategies and the economy in general, confounding all forecasts and going beyond simple technical change. As a consequence for example, improvements in the techniques concerning the exploration and production of hydrocarbons have led to the petrol 'counter-crisis', the reduction in the power of OPEC and undreamed of gains in wealth for certain countries. The progress in gas turbines has led to the reversal of the age-old tendency towards increases in the size of electricity production units and encouraged the liberation of this sector. When looking at the future it is therefore judicious to try and understand the forces at work, and the major trends which result. This is the aim of the articles in this edition of the Revue de l'Energie, published on the occasion of the European colloquium on 'Technical progress faced with the challenges of the energy sector in the future' organised by the Association of Energy Economists. (authors)

  9. International linear collider. A technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, Ned [Argonne National Laboratory, IL (United States); Aderhold, Sebastian [DESY, Hamburg (Germany); Adolphsen, Chris [Stanford Linear Accelerator Center, Menlo Park, CA (United States); and others

    2012-07-01

    The International Linear Collider: A Technical Progress Report marks the halfway point towards the Global Design Effort fulfilling its mandate to follow up the ILC Reference Design Report with a more optimised Technical Design Report (TDR) by the end of 2012. The TDR will be based on much of the work reported here and will contain all the elements needed to propose the ILC to collaborating governments, including a technical design and implementation plan that are realistic and have been better optimised for performance, cost and risk. We are on track to develop detailed plans for the ILC, such that once results from the Large Hadron Collider (LHC) at CERN establish the main science goals and parameters of the next machine, we will be in good position to make a strong proposal for this new major global project in particle physics. The two overriding issues for the ILC R and D programme are to demonstrate that the technical requirements for the accelerator are achievable with practical technologies, and that the ambitious physics goals can be addressed by realistic ILC detectors. This GDE interim report documents the impressive progress on the accelerator technologies that can make the ILC a reality. It highlights results of the technological demonstrations that are giving the community increased confidence that we will be ready to proceed with an ILC project following the TDR. The companion detector and physics report document likewise demonstrates how detector designs can meet the ambitious and detailed physics goals set out by the ILC Steering Committee. LHC results will likely affect the requirements for the machine design and the detectors, and we are monitoring that very closely, intending to adapt our design as those results become available.

  10. Swallowable Wireless Capsule Endoscopy: Progress and Technical Challenges

    Directory of Open Access Journals (Sweden)

    Guobing Pan

    2012-01-01

    Full Text Available Wireless capsule endoscopy (WCE offers a feasible noninvasive way to detect the whole gastrointestinal (GI tract and revolutionizes the diagnosis technology. However, compared with wired endoscopies, the limited working time, the low frame rate, and the low image resolution limit the wider application. The progress of this new technology is reviewed in this paper, and the evolution tendencies are analyzed to be high image resolution, high frame rate, and long working time. Unfortunately, the power supply of capsule endoscope (CE is the bottleneck. Wireless power transmission (WPT is the promising solution to this problem, but is also the technical challenge. Active CE is another tendency and will be the next geneion of the WCE. Nevertheless, it will not come true shortly, unless the practical locomotion mechanism of the active CE in GI tract is achieved. The locomotion mechanism is the other technical challenge, besides the challenge of WPT. The progress about the WPT and the active capsule technology is reviewed.

  11. A technical solution to a difficult problem - An update

    International Nuclear Information System (INIS)

    Asselstine, J.K.

    1985-01-01

    A goal of the Reduced Enrichment Research and Test Reactor Program (RERTR) established by the U.S. Department of Energy is to develop the technical means needed to utilize LEU instead of HEU fuels in research and test reactors and to do so without operational penalties and without affecting safety characteristics. This goal has been pursued now for seven years in cooperation with many of you who are participants in this conference. The program has made significant progress in the development, demonstration and application of new LEU research reactor fuels. According to recent projections, the percentage of HEU fuel in international commerce which is technically replaceable with LEU fuels has been growing steadily as research continues. There appears to be no technical barrier to eventual replacement of HEU fuel with LEU fuel in research and test reactors. While there are many politically complex and technically difficult issues involved in nonproliferation, I conclude that the use of highly enriched weapons grade uranium as a fuel in civilian research reactors stands out as one problem which has a straight forward technical solution. The technical solution is the effort you in the RERTR program are embarked on. Once that solution is in hand, the operators of research reactors are urged to take political and legal initiatives to make the conversion happen. By effecting this conversion they will help minimize the trade in highly enriched uranium and make the world a little safer

  12. A technical solution to a difficult problem - An update

    Energy Technology Data Exchange (ETDEWEB)

    Asselstine, J K

    1985-07-01

    A goal of the Reduced Enrichment Research and Test Reactor Program (RERTR) established by the U.S. Department of Energy is to develop the technical means needed to utilize LEU instead of HEU fuels in research and test reactors and to do so without operational penalties and without affecting safety characteristics. This goal has been pursued now for seven years in cooperation with many of you who are participants in this conference. The program has made significant progress in the development, demonstration and application of new LEU research reactor fuels. According to recent projections, the percentage of HEU fuel in international commerce which is technically replaceable with LEU fuels has been growing steadily as research continues. There appears to be no technical barrier to eventual replacement of HEU fuel with LEU fuel in research and test reactors. While there are many politically complex and technically difficult issues involved in nonproliferation, I conclude that the use of highly enriched weapons grade uranium as a fuel in civilian research reactors stands out as one problem which has a straight forward technical solution. The technical solution is the effort you in the RERTR program are embarked on. Once that solution is in hand, the operators of research reactors are urged to take political and legal initiatives to make the conversion happen. By effecting this conversion they will help minimize the trade in highly enriched uranium and make the world a little safer.

  13. Complex Technical Solution for Renewable Energy

    Directory of Open Access Journals (Sweden)

    Cristian Paul Chioncel

    2010-01-01

    Full Text Available This paper presents a complex technical solution for implementing renewable energy, namely: wind, solar photovoltaic and hydraulics. Because wind and solar photovoltaic energy habe a highly random character, it is required to find solution to store the product energy for unfavorable periods, without wind or solar radiations. This could be achieved using the third type of renewable energy, the hydraulic one, obtained from an hydroelectric pumped storage plant (HPSP, located in the imediate vicinity of the wind and solar photovoltaic plant.

  14. Nuclear theory research. Technical progress report

    International Nuclear Information System (INIS)

    1982-01-01

    Progress is briefly described on the following studies: (1) Dirac phenomenology for deuteron elastic scattering, (2) Dirac wave functions in nuclear distorted wave calculations, (3) impulse approximation for p→p → dπ + reaction above the 3-3 resonance, (4) coherent π production, (5) nuclear potentials from Dirac bound state wavefunctions, (6) nonlocality effects in nuclear reactions, (7) unhappiness factors in DWBA description of (t,p) and (p,t) reactions, (8) absolute normalization of three-nucleon transfer reactions, (9) formulation of a finite-range CCBA computer program, (10) crossing symmetric solutions of the low equations, (11) pion scattering from quark bags, (12) study of the p 11 channel in the delta model, (13) isovector corrections in pion-nucleus scattering, (14) pionic excitation of nuclear giant resonances, and (15) isospin dependence of the second-order pion-nucleus optical potential

  15. Sludge Treatment Evaluation: 1992 Technical progress

    International Nuclear Information System (INIS)

    Silva, L.J.; Felmy, A.R.; Ding, E.R.

    1993-01-01

    This report documents Fiscal Year 1992 technical progress on the Sludge Treatment Evaluation Task, which is being conducted by Pacific Northwest Laboratory. The objective of this task is to develop a capability to predict the performance of pretreatment processes for mixed radioactive and hazardous waste stored at Hanford and other US Department of Energy (DOE) sites. Significant cost savings can be achieved if radionuclides and other undesirable constituents can be effectively separated from the bulk waste prior to final treatment and disposal. This work is initially focused on chemical equilibrium prediction of water washing and acid or base dissolution of Hanford single-shell tank (SST) sludges, but may also be applied to other steps in pretreatment processes or to other wastes. Although SST wastes contain many chemical species, there are relatively few constituents -- Na, Al, NO 3 , NO 2 , PO 4 , SO 4 , and F -- contained in the majority of the waste. These constituents comprise 86% and 74% of samples from B-110 and U-110 SSTS, respectively. The major radionuclides of interest (Cs, Sr, Tc, U) are present in the sludge in small molal quantities. For these constituents, and other important components that are present in small molal quantities, the specific ion-interaction terms used in the Pitzer or NRTL equations may be assumed to be zero for a first approximation. Model development can also be accelerated by considering only the acid or base conditions that apply for the key pretreatment steps. This significantly reduces the number of chemical species and chemical reactions that need to be considered. Therefore, significant progress can be made by developing all the specific ion interactions for a base model and an acid dissolution model

  16. Sludge Treatment Evaluation: 1992 Technical progress

    Energy Technology Data Exchange (ETDEWEB)

    Silva, L J; Felmy, A R; Ding, E R

    1993-01-01

    This report documents Fiscal Year 1992 technical progress on the Sludge Treatment Evaluation Task, which is being conducted by Pacific Northwest Laboratory. The objective of this task is to develop a capability to predict the performance of pretreatment processes for mixed radioactive and hazardous waste stored at Hanford and other US Department of Energy (DOE) sites. Significant cost savings can be achieved if radionuclides and other undesirable constituents can be effectively separated from the bulk waste prior to final treatment and disposal. This work is initially focused on chemical equilibrium prediction of water washing and acid or base dissolution of Hanford single-shell tank (SST) sludges, but may also be applied to other steps in pretreatment processes or to other wastes. Although SST wastes contain many chemical species, there are relatively few constituents -- Na, Al, NO[sub 3], NO[sub 2], PO[sub 4], SO[sub 4], and F -- contained in the majority of the waste. These constituents comprise 86% and 74% of samples from B-110 and U-110 SSTS, respectively. The major radionuclides of interest (Cs, Sr, Tc, U) are present in the sludge in small molal quantities. For these constituents, and other important components that are present in small molal quantities, the specific ion-interaction terms used in the Pitzer or NRTL equations may be assumed to be zero for a first approximation. Model development can also be accelerated by considering only the acid or base conditions that apply for the key pretreatment steps. This significantly reduces the number of chemical species and chemical reactions that need to be considered. Therefore, significant progress can be made by developing all the specific ion interactions for a base model and an acid dissolution model.

  17. Works Technical Department progress report, March 1961

    Energy Technology Data Exchange (ETDEWEB)

    None

    1961-04-19

    This document details the activities of the Savannah River Works Technical Department during the month of March 1961. Topics discussed are: Reactor Technology, Separations Technology, Engineering Assistance, Health Physics, Laboratories Overview, and Technical Papers Issued.

  18. Technical progress by major task. Semiannual technical progress report, September 29, 1997 - March 29, 1998

    International Nuclear Information System (INIS)

    1998-01-01

    The technical progress achieved during the period 29 September 1997 through 29 March 1998 on Contract DE-AC03-91SF18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described in this report. The report is organized by program task structure: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; RTG fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair

  19. Solar lease grant program. Technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    1981-04-01

    Progress on a lease program for the installation of a solar water heater with no installation charge is reported. Information on the announcement of the program, the selection of participants, the contractural agreement, progress on installation of equipment, monitoring, and evaluation is summarized. The status of the budget concerned with the program is announced. Forms used for applications for the program and an announcement from Resource Alternatives for Cilco customers are presented.

  20. New technical solutions in nanotechnology. Part 3

    Directory of Open Access Journals (Sweden)

    IVANOV Leonid Alexeevich

    2016-08-01

    Full Text Available The new technical solutions including inventions in the area of nanotechnology and nanomaterials are efficiently applied in communal and housing services as well as in construction and other joint fields. The invention «Nanomodified epoxy binder for composite materials (RU 2584013» refers to the production of composite materials based on fiber fillers and nanomodified epoxy binder and can be used for manufacture of glass-fiber tubes and other articles for which winding method is used and which are employed in heat networks, hot water supply with delivery method, water supply systems where the temperature can achieve 150°С. Nanomodified epoxy binder for composite materials includes epoxy diane resin and amine hardening agent. The technical result is shorter period of binder hardening, increased heat-resistance and strength characteristics of cured compositions, extended assortment of epoxy compositions with improved technological and performance properties. The specialists may be also interested in the following inventions: composite material based on alloys of the system sn-sb-cu and the method to produce it (RU 2585588, nanomodified epoxy sphere plastic (RU 2587454, the method to produce glass articles with conductive surface (RU 2586123, the method to produce carbon nanotubes with controlled surface density (RU 2569548, solar energy plant (RU 2586034, the method to purify surface and undeground water from titanium and its compounds by means of carbon nanotubes and ultrasound (RU 2575029, elastomeric nanocomposites, compositions of nanocomposites and the methods to produce them (RU 2561170, the method to set heat-resistant pressure sensor based on thin-film nano- and microelectromechanical system (RU 2581454, the method to determine cytotoxicity of nanomaterials based on zinc oxide (RU 2587630, the method to produce nanocores of manganese dioxide (RU 2587439, the method to determine material characteristics by means of nanoindentatio (RU

  1. Access to water: Technical and social solutions help communities ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2010-12-08

    Dec 8, 2010 ... English · Français ... Access to water: Technical and social solutions help communities make the most of ... IDRC-supported research engages communities, and countries, in developing durable solutions to water problems.

  2. New technical solutions in nanotechnology. Part 2

    Directory of Open Access Journals (Sweden)

    IVANOV Leonid Alexeevich

    2016-06-01

    Full Text Available The new technical solutions including inventions in the area of nanotechnology and nanomaterials are efficiently applied in communal and housing services as well as in construction and other joint fields. The invention «The diagnostics method for defects on the metal surfaces (RU 2581441» refers to the methods used to detect defects and cracks on the surface of metal equipment and pipe lines. The suspension of metal nanoparticles is consistently applied on the surface of controlled object following direction from the bigger diameter to the smaller one. The nanoparticles possess the photoluminescence property and their shape is spheric with different diameters. After each application the surface is dried and excessive particles are removed. Then rowwise scanning of object surface is executed with the ray of femtosecond laser and at the same time the intensity of the two-photon luminescence signal is registered in every studied area fixing the location of this area and obtaining the map of glow intensity distribution of nanoparticles exited by the laser radiation. The maps shows the zones with the maximal glow intensity, the coor dinates and shape of the determined glow zone make it possible to determine the coordinates and shape of the defect and the size of its intersection is considered to be equal to relative diameter of the applied nanoparticles at this application stage. The technical stage is increased reliability and credibility of the study. The specialists may be also interested in the following inventions: the method to produce forged pieces from fire-resistant granulated alloys (RU 2583564; the method to produce nanocomposite with double shape memory effect based on monocrystals of ferromagnetic alloy (RU 2583560; the method to produce nanostructured titanium-nickel-zirconium coatings with shape memory (RU 2583222; the method to produce nanocomposites based on golden nanoparticles covered with coating of silica oxide and quantum

  3. New technical solutions in nanotechnology. Part 4

    Directory of Open Access Journals (Sweden)

    IVANOV Leonid Alexeevich

    2016-10-01

    Full Text Available The new technical solutions including inventions in the area of nanotechnology and nanomaterials are efficiently applied in communal and housing services as well as in construction and other joint fields. The invention «The method to produce binder based on phenolformaldehyde resol resin for stratified material, binder and stratified material based on binder and reinforcing fiber base (RU 2594014» refers to polymer composite materials that can be used in manufacture of products designed for aircraft, construction, automobile and household industries. This method is based on component mixing. Resin and fospoliol are taken in dissolvent that is a mix of ethyl alcohol and dimethylformamide. This is the ratio of the components (mass.%: resin – 23,7, dissolvent – 75,3, fospoliol – 1,0. Nanomodifier – mechanically activated diamond - is dispersed into the obtained mixture. The mechanically activated diamond is produced in ball crusher when ration of ball mass and initial detonation nanodiamond is 20:1 respectively and the speed of ball rotation is 900 rotations per minute for 5 minutes. Stratified material based on binder and reinforcing paper fiber is based on aromatic polyamide and possesses finishing layer which composition contents polyamide, ethyl alcohol and water. The binder is applied evenly on the surface of finishing layer, its quantity is equal to the mass of fibers. The technical result is the binder on the basis of phenolformaldehyde resin without volatile flammable liquid and high-toxic substances, 3 times increased shift voltage for compressed products made of stratified materials and 1,3 time decreased inflammability of them. The specialists may be also interested in the following nanotechnological inventions: the method to produce carbon nanostructures modified by metal (RU 2593875; the method of deep purification of monosilane (RU 2593634; the method to produce conductive reticular micro- and nanostructures and the

  4. Progress report [of] Technical Physics Division

    International Nuclear Information System (INIS)

    Vijendran, P.; Deshpande, R.Y.

    1975-01-01

    Activities of the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, over the last few years are reported. This division is engaged in developing various technologies supporting the development of nuclear technology. The various fields in which development is actively being carried out are : (i) vacuum technology, (ii) mass spectrometry, (iii) crystal technology, (iv) cryogenics, and (v) magnet technology. For surface studies, the field emission microscope and the Auger electron spectrometer and other types of spectrometers have been devised and perfected. Electromagnets of requisite strength to be used in MHD programme and NMR instruments are being fabricated. Various crystals such as NaI(Tl), Ge, Fluorides, etc. required as windows and prisms in X and gamma-ray spectroscopy, have been grown. In the cryogenics field, expansion engines required for air liquefaction plants, vacuum insulated dewars, helium gas thermometers etc. have been constructed. In addition to the above, the Division provides consultancy and training to personnel from various institutions and laboratories. Equipment and systems perfected are transferred to commercial organizations for regular production. (A.K.)

  5. Technical solutions to enable embedded generation growth

    Energy Technology Data Exchange (ETDEWEB)

    Lynch, C.A.; Todd, S.; Millar, W.; Wood, H.S.

    2003-07-01

    This report describes the results of one of a series of studies commissioned by the UK Department of Trade and Industry into various aspects of embedded generation with the aim of supporting the development and deployment of electrical sources (particularly their ease of connection to the network) to deliver power to consumers. The first phase of the project involved a literature review and meetings with embedded generation developers and planning engineers from distribution network operators (DNOs). The second phase investigated embedded generation at different levels of the distribution network and included modelling a representative network. Technologies that could facilitate a significant increase in embedded generation were identified and estimates made of when and where significant development would be needed. Technical problems identified by DNOs were concerned with thermal loading, voltage regulation, fault levels, protection and network operation. A number of non-technical (commercial and regulatory) problems were also identified. The report describes the UK regulatory framework, the present situation, the British power system, the accommodation of embedded generation by established means, the representative model and technical innovations.

  6. Marine renewable energies. Stakes and technical solutions

    International Nuclear Information System (INIS)

    Lacroix, Olivier; Macadre, Laura-Mae

    2012-05-01

    Marine renewable energies are able to supply carbon free energy from various ocean resources (tides, waves, currents, winds, salinity and temperature gradients). This sector, currently at an early stage of deployment, has good prospects of development in the coming years. ENEA releases a report on marine renewable energies giving a transversal vision of the associated stakes and prospects of development. Technical and economic characteristics, maturity level and specificities of each marine energy are analyzed. French and European sources of funding, regulatory framework and potential environmental and social impacts are also reported

  7. Bio-methane. Challenges and technical solutions

    International Nuclear Information System (INIS)

    Blaisonneau, Laurent; Carlu, Elieta; Feuillette, Vincent

    2012-06-01

    Among the new energy sectors in development, biogas has many benefits: several valorization possibilities (bio-methane, electricity and heat), continuous production, easy storage. In Europe, and particularly in France, the bio-methane market will be in the next years a driver for the improvement of the economic, environmental and social performance of the actors of the value chain of biogas. ENEA releases a report on the current state of the bio-methane market in Europe. This publication mainly describes: An outlook of the market evolution and the corresponding stakes for the actors of this sector, the technical and economic characteristics, maturity level and specificities of each biogas upgrading process, An analysis of the French regulatory framework for bio-methane injection into the grid

  8. Access to water: Technical and social solutions help communities ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Access to water: Technical and social solutions help communities make the most of available sources. 08 décembre 2010. Image. IDRC Communications. LASTING IMPACTS. IDRC-supported research engages communities, and countries, in developing durable solutions to water problems. Whatever the challenge, people ...

  9. Technical Progress of the New Worlds Observer Mission

    Science.gov (United States)

    Lo, Amy; Noecker, C.; Cash, W.; NWO Study Team

    2009-01-01

    We report on the technical progress of the New Worlds Observer (NWO) mission concept. NWO is a two spacecraft mission that is capable of detecting and characterizing extra-solar, terrestrial planets and planetary systems. NWO consists of an external starshade and an UV-optical space telescope, flying in tandem. The starshade is a petal-shaped, opaque screen that creates an extremely dark shadow large enough to shade the telescope aperture from the target star. The NWO team has been addressing the top technology challenges of the concept, and report here our progress. We will present the current mission configuration best suited to address Terrestrial Planet Finding requirements, and highlight the technological breakthroughs that we have achieved this year. In particular, we will report on progress made in precision deployables for the large starshade, and the trajectory & alignment control system for NWO. We will also briefly highlight advances in understanding the starshade optical performance.

  10. Technical progress safeguards future. Technischer Fortschritt sichert die Zukunft

    Energy Technology Data Exchange (ETDEWEB)

    1985-01-01

    'Technical progress safeguards future', the guiding theme of the 1985 conference of German engineers, calls for discussion. In five lectures representatives of the subdivisions of 'VDI' issued their statements from the viewpoints of their special fields. These lectures were completed by reports on the part of the remaining VDI subdivisions, which are published together with the lectures in this volume. The complex guiding theme is meant to stimulate discussion, which should be conducted also with representatives of other sciences and the public. The volume contains a.o. contributions regarding future prospects, given certain modifications in construction engineering and user behaviour in the sector heating and air-conditioning, regarding the development of new construction techniques to protect the environment, and regarding clean air as an international concern of engineers. For these three contributions separate entries were made. Other presentations relate to: automobile production technology; energy supply as an engineering task; information, invention, innovation as stages of technical progress; progress in materials technology; noise of motor vehicles - current state and future prospects. (orig./HSCH).

  11. International Linear Collider-A Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    Elsen, Eckhard; /DESY; Harrison, Mike; /Brookhaven; Hesla, Leah; /Fermilab; Ross, Marc; /Fermilab; Royole-Degieux, Perrine; /Paris, IN2P3; Takahashi, Rika; /KEK, Tsukuba; Walker, Nicholas; /DESY; Warmbein, Barbara; /DESY; Yamamoto, Akira; /KEK, Tsukuba; Yokoya, Kaoru; /KEK, Tsukuba; Zhang, Min; /Beijing, Inst. High Energy Phys.

    2011-11-04

    The International Linear Collider: A Technical Progress Report marks the halfway point towards the Global Design Effort fulfilling its mandate to follow up the ILC Reference Design Report with a more optimised Technical Design Report (TDR) by the end of 2012. The TDR will be based on much of the work reported here and will contain all the elements needed to propose the ILC to collaborating governments, including a technical design and implementation plan that are realistic and have been better optimised for performance, cost and risk. We are on track to develop detailed plans for the ILC, such that once results from the Large Hadron Collider (LHC) at CERN establish the main science goals and parameters of the next machine, we will be in good position to make a strong proposal for this new major global project in particle physics. The two overriding issues for the ILC R&D programme are to demonstrate that the technical requirements for the accelerator are achievable with practical technologies, and that the ambitious physics goals can be addressed by realistic ILC detectors. This GDE interim report documents the impressive progress on the accelerator technologies that can make the ILC a reality. It highlights results of the technological demonstrations that are giving the community increased confidence that we will be ready to proceed with an ILC project following the TDR. The companion detector and physics report document likewise demonstrates how detector designs can meet the ambitious and detailed physics goals set out by the ILC Steering Committee. LHC results will likely affect the requirements for the machine design and the detectors, and we are monitoring that very closely, intending to adapt our design as those results become available.

  12. Environmental Research Division technical progress report, January 1984-December 1985

    International Nuclear Information System (INIS)

    1986-05-01

    Technical progress in the various research and assessment activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1984 to 1985. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Environmental Impacts, Fundamental Molecular Physics and Chemistry, and Waste Management Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter

  13. Environmental Research Division technical progress report, January 1984-December 1985

    Energy Technology Data Exchange (ETDEWEB)

    1986-05-01

    Technical progress in the various research and assessment activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1984 to 1985. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Environmental Impacts, Fundamental Molecular Physics and Chemistry, and Waste Management Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter.

  14. Cataract and progressing keratoconus — solution?

    Directory of Open Access Journals (Sweden)

    K. B. Pershin

    2015-01-01

    Full Text Available Purpose: To develop an uniform method of the treatment for patients with progressive keratoconus (stage 1‑2 and cataract. Patients and methods: 4 patients (5 eyes with cataract and progressive keratoconus stage 1‑2 were enrolled in the study. Mean age was 42 years. In all patients, standard ophthalmic examination as well corneal topography, anterior segment optical coherence tomography, biometry, and IOL power calculations using IOLMaster were performed. Mean uncorrected visual acuity (UCVA was 0.1 while mean best-corrected visual acuity (BCVA was 0.4. Surgical technique included two steps. The first step was the creation of corneal tunnels with femtosecond laser with subsequent phaco and monofocal aspheric IOL implantation. The second step (1‑2 weeks later was the implantation of intrastromal ring segments based on corneal topography and corneal crosslinking.Results: After the first step, all patients had myopic refraction (from –1.0 D to –2.5 D. Cylindrical component was almost unchanged. After the second step, the patients reported the vision improvement, mainly due to UCVA. Both spherical (myopic and cylindrical components decreased, mainly due to the steep meridian. After the treatment, optical power of the cornea decreased, mainly due to the steep meridian. UCVA was 0.6 or more in 60 % of cases, final BCVA was 0.8‑1.0 in 80 % of cases. Neither intraoperative nor postoperative (follow-up was 2 years complications were observed.Conclusions: Combined phaco and prior creation of corneal tunnels with subsequent intrastromal ring segment implantation and crosslinking in patients with cataract and progressive keratoconus stage 1‑2 is safe, provides good predictable outcome and significantly reduces rehabilitation period.

  15. Technical solutions for low-voltage microgrid concept

    Energy Technology Data Exchange (ETDEWEB)

    Laaksonen, H.

    2011-07-01

    Future electricity distribution networks with large amount of distributed energy resources will require creation of a totally new smart grid architecture. The micro grid concept is expected to play a major role in the new smart grid architecture. A special feature of microgrids is that during disturbances in the utility grid they can continue operation automatically in the island mode so that electricity supply to microgrid customers can be continued without any interruption. Thereby, the microgrid concept allows the reliability benefit of distributed energy resources to be realized while also fulfilling the future energy efficiency requirements. In this thesis a total technical concept for low-voltage microgrid which could be integrated into the future smart grids has been developed and specified. The key technical challenges of low-voltage microgrids are the transition to island operation, the power quality management and the microgrid protection especially during island operation. Essential part of the concept development involved the development of solutions and operation principles to these key technical challenges of low-voltage microgrids so that all these solutions would be compatible with each other. The role of one central energy storage unit and the location of it are very important in the developed concept from the low-voltage microgrid management and protection point of view. The development work with the related technical challenges was carried out in this thesis with PSCAD simulation software. PSCAD enabled the examination of a simultaneous interaction of different types of distributed energy resource units and loads both in the normal utility grid connected and in the island operation mode of the microgrid. This information from simulations with multiple component configurations was essential when the technical solutions were developed and these studies could not have been undertaken to this extent in a laboratory environment without major

  16. Fundamental studies of separation processes. Technical progress report

    International Nuclear Information System (INIS)

    Rogers, L.B.

    1975-06-01

    Studies using high-precision gas chromatography and supercritical fluid chromatography have produced new types of information on liquid crystals and on behavior of substances in the region of the critical temperature, respectively. In addition, the first successful studies of the effects of pressure on cation exchange have been made using aqueous solutions of alkali metal nitrates. In contrast, progress on separations of isotopic species using gas chromatography has been disappointing. In that area, the chief accomplishment has been a determination of the levels of accuracy and precision with which isotopic abundances can be measured using our quadrupole mass spectrometer. (U.S.)

  17. Nonequilibrium photochemical reactions induced by lasers. Technical progress report

    International Nuclear Information System (INIS)

    Steinfeld, J.I.

    1978-04-01

    Research has progressed in six principal subject areas of interest to DOE advanced (laser) isotope separation efforts. These are (1) Infrared double resonance spectroscopy of molecules excited by multiple infrared photon absorption, particularly SF 6 and vinyl chloride. (2) Infrared multiphoton excitation of metastable triplet-state molecules, e.g., biacetyl. (3) An Information Theory analysis of multiphoton excitation and collisional deactivation has been carried out. (4) The mechanism of infrared energy deposition and multiphoton-induced reactions in chlorinated ethylene derivatives; and RRKM (statistical) model accounts for all observed behavior of the system, and a deuterium-specific reaction pathway has been identified. (5) Diffusion-enhanced laser isotope separation in N 16 O/N 18 O. (6) A technical evaluation of laser-induced chemistry and isotope separation

  18. Selection of Technical Solutions for the Management of Radioactive Waste

    International Nuclear Information System (INIS)

    2017-07-01

    The objectives of this publication are to identify and critically review the criteria to be considered while selecting waste management technologies; summarize, evaluate, rank and compare the different technical solutions; and offer a systematic approach for selecting the best matching solution. This publication covers the management of radioactive waste from all nuclear operations, including waste generated from research reactors, power reactors, and nuclear fuel cycle activities including high level waste (HLW) arising from reprocessing and spent nuclear fuel declared as waste (SFW), as well as low level waste (LLW) and intermediate level waste (ILW) arising from the production and use of radionuclides in industry, agriculture, medicine, education and research.

  19. Technical solutions for waste treatment in the Belene project

    International Nuclear Information System (INIS)

    Büttner, K.; Eichhorn, H.

    2011-01-01

    Outline: In June 2010 NUKEM Technologies GmbH was awarded a contract from ATOMSTROYEXPORT JSC to perform the complete work package related to designing and completion of the equipment for treatment of radioactive waste on the turn-key basis for Belene NPP. Technical Solutions: Waste Streams and Technologies at UKC and UKS; Concentration Plant; Thermal Treatment of Resins Sorting Facility; Biological Waste Water Treatment; Conditioning – Cementation • Sorting of Radwaste; Plasma Facility; Grouting; Filter Press; Monitoring and Tracking

  20. Technical and economic feasibility of membrane technology. Fourth technical progress report, June 17-September 16, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Sandre, A.

    1980-10-01

    Progress is reported on the investigation of the potential application of reverse osmosis, ultrafiltration and electrodialysis to the system of solids concentration in beet sugar process streams. During this period, emphasis was put on running reverse osmosis tests with a new prototype machine to select the most suitable membranes for the concentrating of sugar solutions. An economic analysis of using reverse osmosis in a factory producing 10/sup 6/ gal/day of thin juice is discussed. (DMC)

  1. The latest technical solutions in rail vehicles drives

    Directory of Open Access Journals (Sweden)

    Andrzejewski Maciej

    2017-01-01

    Full Text Available The article discusses the latest trends and solutions used in the offers of rail vehicles manufacturers. The study is mainly concerned with the technical solutions used in hybrid rail vehicles, whose development has become one of the priorities for the development of rail vehicles in the European Union in recent years. Stricter emissions standards for harmful compounds in the European Union have forced manufacturers to use increasingly sophisticated technology, including hybrid drives and alternative fuels. The products and solutions offered by the major manufacturers on the market, along with their capabilities and future applications are described. The predicted trends in the development of propulsion technology for rail and road-rail vehicles are also indicated in view of the current legislative aspirations among the EU Member States.

  2. FY 1992 work plan and technical progress reports

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-11-01

    The Desert Research Institute (DRI) is a division of the University of Nevada System devoted to multidisciplinary scientific research. For more than 25 years, DRI has conducted research for the US Department of Energy`s Nevada Field Office (DOE/NV) in support of operations at the Nevada Test Site (NTS). During that time, the research program has grown from an early focus on hydrologic studies to include the areas of geology, archaeology, environmental compliance and monitoring, statistics, database management, public education, and community relations. The range of DRI`s activities has also expanded to include a considerable amount of management and administrative support in addition to scientific investigations. DRI`s work plan for FY 1992 reflects a changing emphasis in DOE/NV activities from nuclear weapons testing to environmental restoration and monitoring. Most of the environmental projects from FY 1991 are continuing, and several new projects have been added to the Environmental Compliance Program. The Office of Technology Development Program, created during FY 1991, also includes a number of environmental projects. This document contains the FY 1992 work plan and quarterly technical progress reports for each DRI project.

  3. Exploring the Capability of Evaluating Technical Solutions: A Collaborative Study into the Primary Technology Classroom

    Science.gov (United States)

    Björkholm, Eva

    2014-01-01

    Within the field of technology education, evaluating technical solutions is considered as an important topic. Research indicates that pupils have difficulties in evaluating technical solutions in terms of fitness for purpose, i.e. how effective a technical solution supports its intended function. By using the learning study, which is an iterative…

  4. Technical Solution for Improved Safeguards/State Cooperation

    International Nuclear Information System (INIS)

    Miller, S.

    2015-01-01

    This paper will discuss an information technology solution to allow the IAEA Safeguards Department to improve cooperation with States. The solution will be a portal or hub to integrate the information, processes, and people between Safeguards and States. It will allow for two-way communication and collaboration between Safeguards staff and State representatives. This paper discusses the information security challenges inherent in building such a system. It proposes technical architectures that might allow the existing integration approach (e.g., encrypted email exchange) to be kept, while expanding it to include modern integration technologies (e.g., web services), as well explorer new collaborative web technologies. It looks at current Safeguards processes and approaches to cooperation and discusses efficiencies that could be achieved through the adoption of this technology solution. Example process areas for improvement include: a) Safeguards Agreements: States are obligated to submit data on their nuclear programme to the IAEA on a periodic basis. Declarations are received through two separate systems using encrypted email. The proposed solution would allow for enhanced exchange of declaration where States can submit any type of declaration using one system. When declarations are received and validated, an acknowledgement would automatically be sent to the State. The solution would provide the Safeguards Department the ability to ask for clarification as well as collaborate on the submitted declarations. Both the question and the response would be recorded in the system. The solution could also integrate tools allowing declarations to be added directly and validated before submission. b) Other areas that could benefit from this solution include declarations from States with small quantities protocol, facility declarations, as well as systems that support extra-budgetary funding (e.g., SPRICS). (author)

  5. Technical project for a new water purification solution

    Directory of Open Access Journals (Sweden)

    Toma Adina

    2018-01-01

    Full Text Available This research is part of the RO-BG Cross-Border Cooperation Program, project “CLEANDANUBE”, MIS-ETC 653, which has finalised by providing a common strategy to prevent the Danube’s pollution technological risks with oil and oil products. This paper presents a new sustainable water purification solution. A short introduction will be offered and an overview regarding the research and new methods to greening the waste is provided. The theoretical aspects of the centrifugal separation phenomenon are studied and the preliminary project bases were established. The paper conveys the possible constructive variations and the technological implications of those. Ultimately, the technical project for a new water purification solution and conclusions with critical points encountered during the designing phase are presented.

  6. Computational model for simulation small testing launcher, technical solution

    Energy Technology Data Exchange (ETDEWEB)

    Chelaru, Teodor-Viorel, E-mail: teodor.chelaru@upb.ro [University POLITEHNICA of Bucharest - Research Center for Aeronautics and Space, Str. Ghe Polizu, nr. 1, Bucharest, Sector 1 (Romania); Cristian, Barbu, E-mail: barbucr@mta.ro [Military Technical Academy, Romania, B-dul. George Coşbuc, nr. 81-83, Bucharest, Sector 5 (Romania); Chelaru, Adrian, E-mail: achelaru@incas.ro [INCAS -National Institute for Aerospace Research Elie Carafoli, B-dul Iuliu Maniu 220, 061126, Bucharest, Sector 6 (Romania)

    2014-12-10

    The purpose of this paper is to present some aspects regarding the computational model and technical solutions for multistage suborbital launcher for testing (SLT) used to test spatial equipment and scientific measurements. The computational model consists in numerical simulation of SLT evolution for different start conditions. The launcher model presented will be with six degrees of freedom (6DOF) and variable mass. The results analysed will be the flight parameters and ballistic performances. The discussions area will focus around the technical possibility to realize a small multi-stage launcher, by recycling military rocket motors. From technical point of view, the paper is focused on national project 'Suborbital Launcher for Testing' (SLT), which is based on hybrid propulsion and control systems, obtained through an original design. Therefore, while classical suborbital sounding rockets are unguided and they use as propulsion solid fuel motor having an uncontrolled ballistic flight, SLT project is introducing a different approach, by proposing the creation of a guided suborbital launcher, which is basically a satellite launcher at a smaller scale, containing its main subsystems. This is why the project itself can be considered an intermediary step in the development of a wider range of launching systems based on hybrid propulsion technology, which may have a major impact in the future European launchers programs. SLT project, as it is shown in the title, has two major objectives: first, a short term objective, which consists in obtaining a suborbital launching system which will be able to go into service in a predictable period of time, and a long term objective that consists in the development and testing of some unconventional sub-systems which will be integrated later in the satellite launcher as a part of the European space program. This is why the technical content of the project must be carried out beyond the range of the existing suborbital

  7. Current progress and technical challenges of flexible liquid crystal displays

    Science.gov (United States)

    Fujikake, Hideo; Sato, Hiroto

    2009-02-01

    We focused on several technical approaches to flexible liquid crystal (LC) display in this report. We have been developing flexible displays using plastic film substrates based on polymer-dispersed LC technology with molecular alignment control. In our representative devices, molecular-aligned polymer walls keep plastic-substrate gap constant without LC alignment disorder, and aligned polymer networks create monostable switching of fast-response ferroelectric LC (FLC) for grayscale capability. In the fabrication process, a high-viscosity FLC/monomer solution was printed, sandwiched and pressed between plastic substrates. Then the polymer walls and networks were sequentially formed based on photo-polymerization-induced phase separation in the nematic phase by two exposure processes of patterned and uniform ultraviolet light. The two flexible backlight films of direct illumination and light-guide methods using small three-primary-color light-emitting diodes were fabricated to obtain high-visibility display images. The fabricated flexible FLC panels were driven by external transistor arrays, internal organic thin film transistor (TFT) arrays, and poly-Si TFT arrays. We achieved full-color moving-image displays using the flexible FLC panel and the flexible backlight film based on field-sequential-color driving technique. Otherwise, for backlight-free flexible LC displays, flexible reflective devices of twisted guest-host nematic LC and cholesteric LC were discussed with molecular-aligned polymer walls. Singlesubstrate device structure and fabrication method using self-standing polymer-stabilized nematic LC film and polymer ceiling layer were also proposed for obtaining LC devices with excellent flexibility.

  8. Technical progress in planning organization of the Ostravo-Karwina coal basin, ''Mining Projects of Ostravo''

    Energy Technology Data Exchange (ETDEWEB)

    Karpeta, B; Kolar, J

    1979-01-01

    Based on the main task of further improvement in labor productivity and improvement in the quality of products, the leading planning organization of the Ostravo-Karwina basin is planning and realizing progressive technological plans based on new equipment. Long-term plans for basin development up to 1990 stipulate a rise in capital investments by 180%, increase in the volume of productivity by 164% with a rise in the number of workers by 142%. Corresponding technical progress in planning is based on an improvement in the system of scientific-technical information, automation and technical equipping of the planning process, improvements in the forms and organizational structure. Organization of specialized research-planning groups to substantiate and to technically-economically evaluate technical progress, and also to develop comprehensive technical assignments is stipulated.

  9. The challenge of the future. Technical progress and ecological perspectives

    International Nuclear Information System (INIS)

    Jischa, M.F.

    1993-01-01

    The book introduces readers into the interrelated global problems population dynamics, energy supply, imminent climate catastrophe, environmetal pollution, finite resources and the conflict between the North and South. It encourages probing more deeply into the technical challenges of the future. The author demonstrates why economic and technical issues will soon be outstripped by questions of the environmental, human and social compatibility of new technologies. (orig./UA) [de

  10. Nuclear waste glass melter: an update of technical progress

    International Nuclear Information System (INIS)

    Brouns, R.A.; Hanson, M.S.

    1984-08-01

    The direct slurry-fed ceramic-lined melter is currently the reference US process for treating defense and civilian high-level liquid waste. Extensive nonradioactive pilot-scale testing at Pacific Northwest Laboratory (PNL) and Savannah River Laboratory has proven the process, defined operating parameters, and identified successful equipment design concepts. Programs at PNL continue to support several of the planned US vitrification plants through preparation of equipment designs and flowsheet testing. Current emphasis is on remotization of equipment, radioactive verification testing, and resolution of remaining technical issues. Development of this technology, technical status, and planned development activities are discussed. 9 references, 4 figures

  11. Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3

    International Nuclear Information System (INIS)

    Ulm, Franz-Josef

    2000-01-01

    OAK-B135 Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3(NOTE: Part II A item 1 indicates ''PAPER'', but a report is attached electronically)

  12. Annual technical progress report: reactor safety, Government fiscal year 1978

    International Nuclear Information System (INIS)

    1978-01-01

    Progress in LMFBR safety studies on accident debris behavior is reported under the following subtask titles: high-temperature-concentration aerosols, large-scale molten fuel tests, sodium release tests, and risk analysis

  13. Technical progress of nuclear energy: economic and environmental prospects

    International Nuclear Information System (INIS)

    Naudet, G.

    1994-01-01

    This document deals with three different aspects of the nuclear energy: first the operating and economic performances of nuclear power plants in the world, the French nuclear competitiveness. Then, the technical and economic perspectives about reactors and fuels cycle and the advantages towards atmospheric pollution are discussed to favour a new worldwide nuclear development. (TEC). 8 refs., 4 figs., 6 tabs

  14. Evaporation by mechanical vapor recompression. Technical progress report, September 1-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Iverson, C.H.; Coury, G.E.

    1979-01-01

    Progress to date in the development of a study of the application of the technologies of mechanical vapor recompression and falling film evaporators as applied to the beet sugar industry is reported. Progress is reported in the following areas: technical literature search and plant visitations of existing applications of VR/FFE.

  15. Conjoint utility analysis of technical maturity and project progress of construction project

    Directory of Open Access Journals (Sweden)

    Ma Wei

    2016-01-01

    Full Text Available In this paper, taking construction project as the research object, the relationship between the project maturity index calculated by the construction project technical risks with different fine degree and the project progress index is studied, and the equilibrium relationship between the Party A’s utility curve and the Party B’s cost curve of using project maturity index and project progress index as the research variables is analyzed. The results show that, when the construction project technical risk division is more precise, the conjoint utility of the project's technical maturity index and the project progress is higher, and the project’s Party A and Party B two sides are closer to the optimal equilibrium. This shows that the construction project technical risk must be finely divided, and managed and controlled respectively, which will help to improve the conjoint utility of the project Party A and Party B two sides.

  16. Environmental Research Division technical progress report: January 1986--October 1987

    International Nuclear Information System (INIS)

    1988-07-01

    Technical process in the various research activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1986-1987. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Fundamental Molecular Physics and Chemistry, and Organic Geochemistry and Environmental Instrumentation Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter. Individual projects under each division are processed separately for the data bases

  17. Environmental Research Division technical progress report: January 1986--October 1987

    Energy Technology Data Exchange (ETDEWEB)

    1988-07-01

    Technical process in the various research activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1986-1987. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Fundamental Molecular Physics and Chemistry, and Organic Geochemistry and Environmental Instrumentation Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter. Individual projects under each division are processed separately for the data bases.

  18. Technical progress report, 1 April-30 June 1981

    Energy Technology Data Exchange (ETDEWEB)

    None

    1981-01-01

    This report describes the technical accomplishments during the quarter ending June 1981, on the commercial nuclear waste management programs under the direction of the Office of Nuclear Waste Isolation (ONWI). The ONWI program is organized into 8 tasks entitled: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management. Principal investigators in each of these areas have submitted summaries of quarterly highlights for inclusion in this report. Separate abstracts have been prepared for 5 of these tasks for inclusion in the Energy Data Base. (DMC)

  19. Technical Progress and Development Directions of Oceanic Spatial Information Datum

    Directory of Open Access Journals (Sweden)

    BAO Jingyang

    2017-10-01

    Full Text Available This paper briefly analyzes the basic development and technical situation of oceanic spatial information datum, reviews the main processes of oceanic vertical datum and correlative oceanic tidal study, such as improvement and perfect methods of determining tidal station vertical datum, realizing form of vertical datum controlled by tidal station, effect on maintaining vertical datum by long-term tidal station, oceanic tidal model establishing, and also construction and transformation of tidal datum, and then forecasts the key development directions of oceanic spatial information datum on high-accuracy marine position service, vertical datum and the transferring model refinement and spatial datum application.

  20. Quarterly technical progress report, February 1, 1996--April 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-28

    This report from the Amarillo National REsource Center for PLutonium provides research highlights and provides information regarding the public dissemination of information. The center is a a scientific resource for information regarding the issues of the storage, disposition, potential utilization and transport of plutonium, high explosives, and other hazardous materials generated from nuclear weapons dismantlement. The center responds to informational needs and interpretation of technical and scientific data raised by interested parties and advisory groups. Also, research efforts are carried out on remedial action programs and biological/agricultural studies.

  1. Crystalline Repository Project. Technical progress report, October 1982-March 1983

    International Nuclear Information System (INIS)

    1985-01-01

    This document reports the progress being made periodically on the development of a geologic repository in crystalline rock for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Crystalline Respository Development (OCRD), a prime contractor of the US Department of Energy Repository Project Office. The studies include work by other prime contractors and by subcontractors to OCRD

  2. C-Mod Collaboration Informal Technical Progress Report

    International Nuclear Information System (INIS)

    Kenneth W. Gentle

    2007-01-01

    The aims of the collaboration have not changed. A specific list of tasks was agreed upon during the Fall of 2006 in preparation for the 2007 C-Mod campaign by Earl Marmar, Head of the Alcator Project, Kenneth Gentle, Principal Investigator, and William Rowan, Collaboration Coordinator with the facilitation of Adam Rosenberg (DOE grant monitor for the collaboration). The activities follow the list of tasks and are discussed in this progress report

  3. Progress report of Technical Physics Division: April 1980 - March 1982

    International Nuclear Information System (INIS)

    Chaudhry, Ramesh; Vijendran, P.

    1983-01-01

    Activities, with an individual summary of each, of the Technical Physics Division (TPD) of the Bhabha Atomic Research Centre (BARC), Bombay are reported for the period April 1980 - March 1982. The major thrust of the TPD's work has been in: (i) design and fabrication of instruments, devices and equipment and (ii) development of techniques in the frontline research and technology areas like vacuum science, surface analysis, cryogenics and crystal growing. The Division also provided custombuilt electronics equipment, vacuum systems and glass components and devices to the various Divisions of BARC and other units of the DAE. Training and manpower development activities and technology transfer activities are also reported. Lists of seminars, colloquia, publications during the period of the report are given. (M.G.B.)

  4. Progress report for 1978-79, Technical Physics Division

    International Nuclear Information System (INIS)

    Gopalaraman, C.P.; Deshpande, R.Y.

    1980-01-01

    The research and development activities of the Technical Physics Division (TPD) of the Bhabha Atomic Research Centre, Bombay, during the calendar years 1978 and 1979 are reported. The TPD's major areas of work are electronics instrumentation, crystal technology, mass spectrometers, cryogenic equipment and vacuum equipment. Some of the major achievements are: (1) fabrication of various electronic instruments and components for the pulsed nuclear magnetic resonance spectrometers, (2) growth of large size NaI(Tl) and Ge crystals, (3) growth of CsI, KDP and arsenic selenide crystals, (4) fabrication of quadrupole mass filters and (5) fabrication of mass spectrometers for gas analysis and D/H analysis in water samples. (M.G.B.)

  5. Electronic refrigerant leak detector. Quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Talamas, E. Jr.

    1998-10-15

    The project comprises three main tasks. They are (1) Develop, design, and fabricate sensors, (2) Develop, design, and fabricate test instruments, (3) Testing and data analysis. The milestone includes 17 sub-tasks for the 52-weeks project period, starting on May 1, 1998 and ending on April 30, 1999. As stated in the Application for Federal Assistance, Micronic intended to relocate to a new office by June of 1998. This decision was delayed, since the first partial payment was transferred on August 12, 1998. Micronic plans to relocate this November. A second Provisional Application for a US patent has been filed. Progress made during this period is reported.

  6. The role of technical progress in the process of recalculating oil reserves

    International Nuclear Information System (INIS)

    Boulard, J.N.

    1999-01-01

    Contrary to the concept of resources (which is essentially a geological one), the notion of reserves designates the quantities that are technically and economically recoverable. Beyond the production-related effect, the reserves therefore evolve over time in accordance with numerous technical and economic parameters. Among these parameters, it can be seen that technical progress plays a considerable role throughout the process of converting resources into reserves, including progress in the identification, accessibility and processing of the resources, and improvements in economic viability. After having tackled the problem of measuring the 'technical progress effects' and citing examples, we demonstrate that the evolution in oil reserves is subject to three types of impact. These are a quantitative impact by significantly improving the recovery rates or making it possible to identify hitherto undetectable oil fields, a qualitative impact by widening the resource base thanks to the adoption of new categories of oil (in particular the so-called 'unconventional' oils) and by carrying out the gradual substitution between these resources of differing qualities. There is also a dynamic impact, through the acceleration of resource availability. Through these three approaches, technical progress makes makes it possible to ensure continuity in oil supply and contributes significantly to the recalculation of reserves. It therefore acts as a compensating factor, counterbalancing the progressive depletion of resources. (author)

  7. Technical progress report, October 1, 1980-September 30, 1981

    International Nuclear Information System (INIS)

    1981-01-01

    Progress during the 12-month period, October 1, 1980 to September 30, 1981 on the University of Wisconsin Plasma Physics contract is described. Most of the work centers around two major experimental devices, the Levitated Octupole and Tokapole II. A major upgrade of the Octupole is underway to include 2 MW of ICRH and 1.8 MW of neutral beam heating. Meanwhile, gun optimization and low field operation has resulted in the attainment of 35% beta, a factor of 9 above the single fluid ballooning limit. The ICRH experiment is well underway, and the first neutral beam source has been installed. The Tokapole is operating reliably at the full design field of 10 kG with 12 msec discharges. Low q (approx. 0.4) discharges with flat current profiles are obtained at reduced (approx. 3kG) toroidal field. The device is presently being used to study shear Alfven wave heating, ECRH startup, poloidal ohmic heating, and plasma transport

  8. TECHNICAL TRAINING SEMINAR: High Temperature Superconductors: Progress and Issues

    CERN Multimedia

    Davide Vitè

    2002-01-01

    Monday 24 June from 14:30 to 15:30 - Training Centre Auditorium - bldg. 593-11 High Temperature Superconductors: Progress and Issues Prof. Jan Evetts / UNIVERSITY OF CAMBRIDGE, Department of Materials Science and Metallurgy, UK Grappling with grain boundaries: Current transport processes in granular High Temperature Superconductors (HTS) The development of High Temperature Superconductors, seen from a materials scientist's point of view, is relevant to the superconductivity community at CERN: their possible high current applications can include high performance magnets for future accelerators. There is an urgent need to develop a quantitative description of HTS conductors in terms of their complex anisotropy, inhomogeneity and dimensionality. This is essential both for the practical specification of a conductor and for charting routes to conductor optimisation. The critical current, the n-value, dissipation and quenching characteristics are amongst most important parameters that make up an engineering specifi...

  9. Technical progress review of extraction of uranium from fly ash

    International Nuclear Information System (INIS)

    Gao Renxi; Gao Junning; Wu Qingming; Chen Gang; Wan Hongjin; Zhang Ziyue

    2014-01-01

    The increasing of fly ash in coal-fired power plants at home and abroad year by year and the potential impacts to the environment attracted media attention. Although the extraction of uranium from the fly ash in coal-fired power plants had optional process from technique aspect and sufficient preliminary researches, but considering the low grade of the uranium in fly ash and particularity of the mineral composition, it is easy to have a high cost of extraction. As a consequence, it is not included in the development plan of uranium mining and metallurgy. The present applications of fly ash are only building materials, building roads and pit valley backfill, the resource utilization rate was low and was still in its early stages of development and application. In view of this, the research advances and the latest development trends of extraction of uranium from fly ash at home and abroad were introduced from the technical aspect, and the beneficial analyzes of the prospect and advices to this industry were given. (authors)

  10. Texas Experimental Tokamak, a plasma research facility: Technical progress report

    International Nuclear Information System (INIS)

    Wootton, A.J.

    1995-08-01

    In the year just past, the authors made major progress in understanding turbulence and transport in both core and edge. Development of the capability for turbulence measurements throughout the poloidal cross section and intelligent consideration of the observed asymmetries, played a critical role in this work. In their confinement studies, a limited plasma with strong, H-mode-like characteristics serendipitously appeared and received extensive study though a diverted H-mode remains elusive. In the plasma edge, they appear to be close to isolating a turbulence drive mechanism. These are major advances of benefit to the community at large, and they followed from incremental improvements in diagnostics, in the interpretation of the diagnostics, and in TEXT itself. Their general philosophy is that the understanding of plasma physics must be part of any intelligent fusion program, and that basic experimental research is the most important part of any such program. The work here demonstrates a continuing dedication to the problems of plasma transport which continue to plague the community and are an impediment to the design of future devices. They expect to show here that they approach this problem consistently, systematically, and effectively

  11. ERIP invention 637. Technical progress report 2nd quarter, April 1997--June 1997

    Energy Technology Data Exchange (ETDEWEB)

    Thacker, G.W.

    1997-07-22

    This technical report describes progress in the development of the Pegasus plow, a stalk and root embedding apparatus. Prototype testing is reported, and includes the addition of precision tillage. Disease data, organic matter, and nitrogen levels results are very briefly described. Progress in marketing is also reported. Current marketing issues include test use by cotton and wheat growers, establishment of dealer relationships, incorporation of design modifications, expansion of marketing activities, and expansion of loan and lease program.

  12. IRIS International Reactor Innovative and Secure Final Technical Progress Report

    International Nuclear Information System (INIS)

    Carelli, M.D.

    2003-01-01

    OAK-B135 This NERI project, originally started as the Secure Transportable Autonomous Light Water Reactor (STAR-LW) and currently known as the International Reactor Innovative and Secure (IRIS) project, had the objective of investigating a novel type of water-cooled reactor to satisfy the Generation IV goals: fuel cycle sustainability, enhanced reliability and safety, and improved economics. The research objectives over the three-year (1999-2002) program were as follows: First year: Assess various design alternatives and establish main characteristics of a point design; Second year: Perform feasibility and engineering assessment of the selected design solutions; Third year: Complete reactor design and performance evaluation, including cost assessment These objectives were fully attained and actually they served to launch IRIS as a full fledged project for eventual commercial deployment. The program did not terminate in 2002 at the end of the NERI program, and has just entered in its fifth year. This has been made possible by the IRIS project participants which have grown from the original four member, two-countries team to the current twenty members, nine countries consortium. All the consortium members work under their own funding and it is estimated that the value of their in-kind contributions over the life of the project has been of the order of $30M. Currently, approximately 100 people worldwide are involved in the project. A very important constituency of the IRIS project is the academia: 7 universities from four countries are members of the consortium and five more US universities are associated via parallel NERI programs. To date, 97 students have worked or are working on IRIS; 59 IRIS-related graduate theses have been prepared or are in preparation, and 41 of these students have already graduated with M.S. (33) or Ph.D. (8) degrees. This ''final'' report (final only as far as the NERI program is concerned) summarizes the work performed in the first four

  13. Technical progress in INPRO activities on modelling and innovation

    International Nuclear Information System (INIS)

    Villalibre, P.; Haas, E.; Khartabil, H.; Kim, S.; Korinny, A.; Usanov, V. and others

    2010-01-01

    Among the 31 Members of the 'International Project on Innovative Nuclear Reactors and Fuel Cycles' (INPRO) in April 2010, more than 20 are cooperating in the implementation of Collaborative Projects (CPs) related to the four substantive Programme Areas of the INPRO Action Plan. The purpose of the CPs is to contribute to the achievement of goals established in the programmatic areas. This paper presents progress status of several CPs dealing with Modelling and Innovation: - CP on Environmental Impact Benchmarking applicable to Nuclear Energy Systems under Normal Operation (ENV): A benchmark of codes and methods for determining radiation released during normal operation of nuclear facilities is performed by using established source term, release scenario, and target group (humans). - CP on Proliferation Resistance: Acquisition/Diversion Pathway Analysis (PRADA): 'PRADA' addresses the identification and analyses of high level pathways for the acquisition of weapons usable material, and makes recommendations for evaluating the multiplicity and robustness of barriers against proliferation. PRADA develops a case study based on DUPIC fuel cycle. The outcome from the project will support the assessment methodologies developed at GIF and INPRO. - CP on Global Architecture of Nuclear Energy Systems based on Thermal and Fast Reactors including Closed Fuel Cycle (GAINS): GAINS objective is to develop a methodological platform for assessing future nuclear energy systems taking into account the sustainable development, and to validate the results through sample analyses. High and moderate scenarios of nuclear energy demand and supply during the Century (5000 and 2500 GWe respectively in the year 2100) are being analysed using homogeneous and heterogeneous considerations. A non-geographic approach grouping the countries according to their planned use of nuclear energy has being established. - CP on Investigations of the 233 U/Th Fuel Cycle (ThFC): ThFC objective is to explore FC

  14. Hazardous Waste Cleanup: Veolia ES Technical Solutions, L.L.C. in Middlesex, New Jersey

    Science.gov (United States)

    Veolia ES Technical Solutions is located at 125 Factory Lane in Middlesex, New Jersey. Veolia owns and operates a solvent-reprocessing facility that is located on a four-acre site in an industrial area of Middlesex Borough.

  15. Institutional effectiveness of REDD+ MRV: Countries progress in implementing technical guidelines and good governance requirements

    NARCIS (Netherlands)

    Ochieng, R.M.; Visseren-Hamakers, Ingrid; Arts, B.; Brockhaus, M.; Herold, M.

    2016-01-01

    The UNFCCC requires REDD+ countries wishing to receive results-based payments to measure, report and verify (MRV) REDD+ impacts; and outlines technical guidelines and good governance requirements for MRV. This article examines institutional effectiveness of REDD+ MRV by assessing countries’ progress

  16. Studies in theoretical high energy particle physics: Technical progress report [February 1987-February 1988

    International Nuclear Information System (INIS)

    Sukhatme, U.P.; Keung, Wai-Yee; Kovacs, E.

    1988-02-01

    This is a technical progress report for grant No. FG02-84ER40173 for the period February 1987 to February 1988. Our research on supersymmetric quantum mechanics has yielded many interesting results. In particular, a systematic approach to the tunneling problem in double well potentials has been developed. Higgs boson related physics at the high energy hadron colliders has been extensively studied

  17. Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1--July 31, 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Progress is reported on research projects related to the following: Electronic resource library; Environment, safety, and health; Communication, education, training, and community involvement; Nuclear and other materials; and Reporting, evaluation, monitoring, and administration. Technical studies investigate remedial action of high explosives-contaminated lands, radioactive waste management, nondestructive assay methods, and plutonium processing, handling, and storage.

  18. Cassini RTG Program. Monthly technical progress report, 27 November--31 December 1995

    International Nuclear Information System (INIS)

    1996-01-01

    This monthly technical progress report provided information on the following tasks: spacecraft integration and liaison; engineering support; safety analysis; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, and reliability, and contractor acquired government owned (CAGO) property acquisition

  19. Technical progress faced with the challenges of the energy sector in the future

    International Nuclear Information System (INIS)

    Maillard, D.

    1999-01-01

    The colloquium organised by the Association of Energy Economists dealing with the theme 'Technical progress faced with the challenges of the energy sector in the future' takes place against a backdrop of ever-increasing initiatives in this field, for example at the World Energy Council or the International Energy Agency Faith in technical progress is widespread but should be supported by studies without any preconceived ideas. Research and development efforts must be fully supported, and in a climate of opening markets and liberalization the public authorities have a major role to pay. Historically, the markets have always been able to meet new needs thanks to technology, but the ambitious targets that the international community has set itself regarding the emission of greenhouse gases imply technical improvements and major investments. (authors)

  20. Stockholm international conference 2003 on geological repositories: Political and technical progress

    International Nuclear Information System (INIS)

    2004-01-01

    The conference reviewed global progress made as well as current perspectives on the activities to develop geologic repositories. The objectives were to review the progress in policy making as well as technical issues and to strengthen international co-operation on waste management and disposal issues. The first day of the conference addressed the policy aspects of geological repositories and the second day featured the more technical issues. Session 1: International progress in performing long-term safety studies and security of geological disposal were discussed and reviewed with examples from OECD/NEA, Belgium, Sweden, USA, Switzerland and Russia. Session 2: Views on stakeholder involvement and decision making process were presented by international organisations and national implementers from Japan, United Kingdom, Belgium and OECD/NEA. Session 3: Views on stakeholder involvement and decision making process were presented by regional and local stakeholders from France, Finland, Korea and Sweden. Session 4: International instruments assisting in the implementation of geological repositories were discussed, for example ICRP and IAEA/NEA safety documents, Joint Convention, Safeguard agreements, Nuclear Liability Conventions, etc. Session 5: The contribution of Research, Development and Demonstration was discussed with overviews of the progress achieved on scientific and technical issues over the past four years. Progress and key issues were presented from Switzerland, USA, Finland, Japan, Sweden and IAEA. Each of the papers and poster presentations have been analysed and indexed separately

  1. Technical meeting on progress in managing, and limiting the consequences of events exceeding the design basis

    International Nuclear Information System (INIS)

    Fabian, H.

    2004-01-01

    The Technical Groups on 'Reactor Safety' and 'Thermodynamics and Fluid Dynamics' of the Kerntechnische Gesellschaft e.V. organized a joint technical meeting on 'Progress in Managing, and Limiting the Consequences of, Events Exceeding the Design Basis' at the FTU Training Center of the Karlsruhe Research Center. The topic chosen, the papers presented, the presenters, and the non-technical part of the program met with lively interest on the part of institutions in the nuclear field. These were the objectives of the technical meeting: - Establishing a forum for communicating relevant topics. - In-depth discussion of the main topic, i.e. the advanced development of reactor safety, research in the field, and its application, in twenty selected papers presented by speakers from different institutions. - Presentation of topical work in a nuclear technology institution, the Karlsruhe Research Center. (orig.) [de

  2. Treating limbs with electrons: creative solutions to technical problems

    International Nuclear Information System (INIS)

    Hornby, C.

    1993-01-01

    The treatment of superficial lesions on limbs involving large areas of skin has long presented a challenge to radiation therapists. In the 1990's the use of electrons provides a good selection of field sizes and beam penetrations. However, the rapidly varying contours of limbs as well as their mobility, continues to necessitate solutions to the problems of accurate field definition, homogeneous dose in particularly at beam junctions and, simple but effective patient stabilization. This paper offers several examples of creative solutions to these problems. 8 refs., 17 figs

  3. Technical solutions for mitigating security threats caused by health professionals in clinical settings.

    Science.gov (United States)

    Fernandez-Aleman, Jose Luis; Belen Sanchez Garcia, Ana; Garcia-Mateos, Gines; Toval, Ambrosio

    2015-08-01

    The objective of this paper is to present a brief description of technical solutions for health information system security threats caused by inadequate security and privacy practices in healthcare professionals. A literature search was carried out in ScienceDirect, ACM Digital Library and IEEE Digital Library to find papers reporting technical solutions for certain security problems in information systems used in clinical settings. A total of 17 technical solutions were identified: measures for password security, the secure use of e-mail, the Internet, portable storage devices, printers and screens. Although technical safeguards are essential to the security of healthcare organization's information systems, good training, awareness programs and adopting a proper information security policy are particularly important to prevent insiders from causing security incidents.

  4. Wireline coring/open center reaming: Technical problems and solutions

    International Nuclear Information System (INIS)

    Fehr, G.

    1996-01-01

    At the 1993 ASME Energy Technology Conference, a paper, ''Field Experience with Wireline Coring through a Dual Wall Drilling System'', was presented. It described the initial scientific drilling which started in the spring of 1992 using wireline coring within a 9 5/8 inch dual wall drill pipe through an open center reaming bit, and some of the improvements made since the prototype drilling tests. New and as yet unsolved problems were identified. This follow-on work brings the industry up-to-date with a survey of how these difficulties have been solved, or, if not solved, the status of the effort made for each of the air coring/reaming technical challenges on the Yucca Mountain Site Characterization Project at the US Department of Energy Nevada Test Site

  5. Total Factor Productivity Growth, Technical Progress & Efficiency Change in Vietnam Coal Industry - Nonparametric Approach

    Science.gov (United States)

    Phuong, Vu Hung

    2018-03-01

    This research applies Data Envelopment Analysis (DEA) approach to analyze Total Factor Productivity (TFP) and efficiency changes in Vietnam coal mining industry from 2007 to 2013. The TFP of Vietnam coal mining companies decreased due to slow technological progress and unimproved efficiency. The decadence of technical efficiency in many enterprises proved that the coal mining industry has a large potential to increase productivity through technical efficiency improvement. Enhancing human resource training, technology and research & development investment could help the industry to improve efficiency and productivity in Vietnam coal mining industry.

  6. Satellite end of life constraints: Technical and organisational solutions

    Science.gov (United States)

    Cabrières, Bernard; Alby, Fernand; Cazaux, Christian

    2012-04-01

    Since 1974 with the radiocommunication satellite Symphony1, CNES launched and operated 11 GEO and 20 LEO satellites. During those 36 years, both flight segment and ground segment dramatically evolved and operational organisations and techniques equally improved. At the present time, CNES operates 1 GEO satellite and 17 LEO satellites with not much more people and costs than in 1986 when its first Satellite Operation Direction in Toulouse was only in charge of Telecom1A, Telecom1B and Spot1. This fantastic technical evolution combined with the huge increase of services to citizens and governments given by Space systems was unfortunately also associated with an enormous growth of space pollution by debris of all sizes. From the beginning, CNES was a major actor of the international effort to promote regulations in order to try to reduce or at least control this problematic situation. Internally, CNES, not only set up an operational on-call service to deal with collision risks, but decided to do its best to apply the new guidelines to the end of life of satellites under its responsibility even for those developed and launched a very long time ago. For instance, that was the case in 2009 for the reorbitation of the GEO satellite Telecom 2C (launched in 1995) and for the deorbitation of the LEO satellite Spot2 (launched in 1990). In addition, CNES prepares procedures to be able to be as exemplary as possible for its other spacecrafts whose end of life approaches. The constraints and challenges to face in order to cope with these new requirements are multiple: choice of final orbit, realistic calculation of re-entry duration, estimation of residual propellant, electric passivation, management of explosion risks… All these studies and operational experience gained will be helpful for the new role of CNES, which recently became in charge of controlling space operators in the frame of the new French space law on space operations.

  7. Productivity Change, Technical Progress, and Relative Efficiency Change in the Public Accounting Industry

    OpenAIRE

    Rajiv D. Banker; Hsihui Chang; Ram Natarajan

    2005-01-01

    We present evidence on components of productivity change in the public accounting industry toward the end of the 20th century. Using revenue and human resource data from 64 of the 100 largest public accounting firms in the United States for the 1995--1999 period, we analyze productivity change, technical progress, and relative efficiency change over time. The average public accounting firm experienced a productivity growth of 9.5% between 1995 and 1999. We find support for the hypothesis that...

  8. Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Reports on a quarterly basis. This report comprises the first Quarterly Technical Progress Report for Year 2 of the Agreement. This report reflects the progress and/or efforts performed on the sixteen (16) technical projects encompassed by the Year 2 Agreement for the period of January 1 through March 31, 1994. In situ bioremediation of chlorinated organic solvents; Microbial enrichment for enhancing in-situ biodegradation of hazardous organic wastes; Treatment of volatile organic compounds (VOCs) using biofilters; Drain-enhanced soil flushing (DESF) for organic contaminants removal; Chemical destruction of chlorinated organic compounds; Remediation of hazardous sites with steam reforming; Soil decontamination with a packed flotation column; Use of granular activated carbon columns for the simultaneous removal of organics, heavy metals, and radionuclides; Monolayer and multilayer self-assembled polyion films for gas-phase chemical sensors; Compact mercuric iodide detector technology development; Evaluation of IR and mass spectrometric techniques for on-site monitoring of volatile organic compounds; A systematic database of the state of hazardous waste clean-up technologies; Dust control methods for insitu nuclear and hazardous waste handling; Winfield Lock and Dam remediation; and Socio-economic assessment of alternative environmental restoration technologies.

  9. Foundations for technical solutions in organizing excavation of open ore pits

    OpenAIRE

    С. И. Фомин

    2016-01-01

    To study stochastic mining technical systems of opencast mines, where parallel to clearly defined values random and indefinite factors operate, probabilistic and statistical techniques are mostly used nowadays. Formally, the task of producing a design solution may, under the conditions of indeterminacy be transformed into an equivalent deterministic problem formulated for a risky situation. Uncertainty in the initial mining, geological and technical-economic information available during t...

  10. Experimental Facilities Division/User Program Division technical progress report 1999-2000

    International Nuclear Information System (INIS)

    2001-01-01

    In October 1999, the two divisions of the Advanced Photon Source (APS), the Accelerator Systems Division (ASD) and the Experimental Facilities Division (XFD), were reorganized into four divisions (see high-level APS organizational chart, Fig. 1.1). In addition to ASD and XFD, two new divisions were created, the APS Operations Division (AOD), to oversee APS operations, and the User Program Division (UPD), to serve the APS user community by developing and maintaining the highest quality user technical and administration support. Previous XFD Progress Reports (ANL/APS/TB-30 and ANL/APS/TB-34) covered a much broader base, including APS user administrative support and what was previously XFD operations (front ends, interlocks, etc.) This Progress Report summarizes the main scientific and technical activities of XFD, and the technical support, research and development (R and D) activities of UPD from October 1998 through November 2000. The report is divided into four major sections, (1) Introduction, (2) SRI-CAT Beamlines, Technical Developments, and Scientific Applications, (3) User Technical Support, and (4) Major Plans for the Future. Sections 2 and 3 describe the technical activities and research accomplishments of the XFD and UPD personnel in supporting the synchrotron radiation instrumentation (SRI) collaborative access team (CAT) and the general APS user community. Also included in this report is a comprehensive list of publications (Appendix 1) and presentations (Appendix 2) by XFD and UPD staff during the time period covered by this report. The organization of section 2, SRI CAT Beamlines, Technical Developments, and Scientific Applications has been made along scientific techniques/disciplines and not ''geographical'' boundaries of the sectors in which the work was performed. Therefore items under the subsection X-ray Imaging and Microfocusing could have been (and were) performed on several different beamlines by staff in different divisions. The management of

  11. Progress towards CSR RL06 GRACE gravity solutions

    Science.gov (United States)

    Save, Himanshu

    2017-04-01

    The GRACE project plans to re-processes the GRACE mission data in order to be consistent with the first gravity products released by the GRACE-FO project. The next generation Release-06 (RL06) gravity products from GRACE will include the improvements in GRACE Level-1 data products, background gravity models and the processing methodology. This paper will outline the planned improvements for CSR - RL06 and discuss the preliminary results. This paper will discuss the evolution of the quality of the GRACE solutions, especially over the past few years. We will also discuss the possible challenges we may face in connecting/extending the measurements of mass fluxes from the GRACE era to the GRACE-FO era due quality of the GRACE solutions from recent years.

  12. Volatiles combustion in fluidized beds. Technical progress report, 4 March 1993--3 June 1993

    Energy Technology Data Exchange (ETDEWEB)

    Hesketh, R.P.

    1993-09-01

    The goal of this project is to investigate the conditions in which volatiles will burn within both the dense and freeboard regions of fluidized beds. Experiments using a fluidized bed operated at incipient fluidization will be performed to characterize the effect of particle surface area, initial fuel concentration, and particle type on the inhibition of volatiles within a fluidized bed. The work conducted during the period 4 March, 1993 through 3 June, 1993 is reported in this technical progress report. The work during this time period consists primarily of the startup and trouble shooting of the fluidized bed reactor and gas phase modeling of methane and propane.

  13. National Council on Radiation Protection and Measurements semiannual technical progress report, March 1989--August 1989

    International Nuclear Information System (INIS)

    Ney, W.R.

    1991-01-01

    This semiannual technical progress report is for the period 1 March 1989 through 31 August 1989. This National Council on Radiation Protection and Measurements (NCRP) program is designed to provide recommendations for radiation protection based on scientific principles. During this period several reports were published covering the topics of occupational radiation exposure, medical exposure, radon control, dosimetry, and radiation protection standards. Accomplishments of various committees are also reported; including the committees on dental x-ray protection, radiation safety in uranium mining and milling, ALARA, instrumentation, records maintenance, occupational exposures of medical personnel, emergency planning, and others. (SM)

  14. Technical progress and efficiency changes in football teams participating in the UEFA Champions League

    Directory of Open Access Journals (Sweden)

    Lucía Isabel García Cebrián

    2015-09-01

    Full Text Available This paper commits to calculate and analyze productivy levels and its components for teams that participated in the UEFA Champions League between 2003 and 2012. It will pursue three objectives: 1 evaluate resources usage, 2 analyze the productivity levels of the football teams and the sports results, and 3 see the influence of participation experience in reference to productivity and sports results. Using Malmquist Productivity Index, the results reflect a lack of consistent progression of efficiency, productivity, and technical change. This competition does not reward the efficient usage of resources and there is not a conclusive relationshop between permanence in the competition and productivity.

  15. Western Research Institute: Annual technical progress report, October 1987--September 1988

    Energy Technology Data Exchange (ETDEWEB)

    1988-12-01

    This report describes the technical progress made by the Western Research Institute of the University of Wyoming Research Institute of the University of Wyoming Research Corporation on work performed for the period October 1, 1987 through September 30, 1988. This research involves five resource areas: oil shale, tar sand, underground coal gasification, advanced process technology, and advanced fuels research. Under the terms of the cooperative agreement, an annual project plan has been approved by DOE. The work reported herein reflects the implementation of the research in the plan and follows the structure used therein. 49 refs., 32 figs., 87 tabs.

  16. Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-04-01

    This reports reports the progress/efforts performed on six technical projects: 1. systematic assessment of the state of hazardous waste clean-up technologies; 2. site remediation technologies (SRT):drain- enhanced soil flushing for organic contaminants removal; 3. SRT: in situ bio-remediation of organic contaminants; 4. excavation systems for hazardous waste sites: dust control methods for in-situ nuclear waste handling; 5. chemical destruction of polychlorinated biphenyls; and 6. development of organic sensors: monolayer and multilayer self-assembled films for chemical sensors.

  17. Nuclear structure theory. Annual technical progress report, October 1, 1976--September 30, 1977

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1977-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: (1) statistical spectroscopy, including giant resonances for beta and electromagnetic excitation and sum rules (including inverse-energy-weighted sum rules), statistical methods of truncating shell model spaces and renormalization of operators, study of state labelling and ''chains'' of groups, evaluation of fluctuation measures, technical aspects of operator averaging; (2) meson interactions with nuclei, including scattering and absorption of mesons by nuclei (general methods), models for absorption, single- and double-charge exchange of pions, role of rho mesons

  18. Uremic Solutes in Chronic Kidney Disease and Their Role in Progression.

    Directory of Open Access Journals (Sweden)

    Jan A J G van den Brand

    Full Text Available To date, over 150 possible uremic solutes have been listed, but their role in the progression of CKD is largely unknown. Here, the association between a selected panel of uremic solutes and progression in CKD patients was investigated.Patients from the MASTERPLAN study, a randomized controlled trial in CKD patients with a creatinine clearance between 20 and 70 ml/min per 1.73m2, were selected based on their rate of eGFR decline during the first five years of follow-up. They were categorized as rapid (decline >5 ml/min per year or slow progressors. Concentrations of eleven uremic solutes were obtained at baseline and after one year of follow-up. Logistic regression was used to compare the odds for rapid to slow progression by uremic solute concentrations at baseline. Variability in uremic solute levels was assessed using scatter plots, and limits of variability were calculated.In total, 40 rapidly and 40 slowly progressing patients were included. Uremic solutes were elevated in all patients compared to reference values for healthy persons. The serum levels of uremic solutes were not associated with rapid progression. Moreover, we observed substantial variability in solute levels over time.Elevated concentrations of uremic solutes measured in this study did not explain differences in rate of eGFR decline in CKD patients, possibly due to lack of power as a result of the small sample size, substantial between patient variability, and variability in solute concentrations over time. The etiology of intra-individual variation in uremic solute levels remains to be elucidated.

  19. Uremic Solutes in Chronic Kidney Disease and Their Role in Progression.

    Science.gov (United States)

    van den Brand, Jan A J G; Mutsaers, Henricus A M; van Zuilen, Arjan D; Blankestijn, Peter J; van den Broek, Petra H; Russel, Frans G M; Masereeuw, Rosalinde; Wetzels, Jack F M

    2016-01-01

    To date, over 150 possible uremic solutes have been listed, but their role in the progression of CKD is largely unknown. Here, the association between a selected panel of uremic solutes and progression in CKD patients was investigated. Patients from the MASTERPLAN study, a randomized controlled trial in CKD patients with a creatinine clearance between 20 and 70 ml/min per 1.73m2, were selected based on their rate of eGFR decline during the first five years of follow-up. They were categorized as rapid (decline >5 ml/min per year) or slow progressors. Concentrations of eleven uremic solutes were obtained at baseline and after one year of follow-up. Logistic regression was used to compare the odds for rapid to slow progression by uremic solute concentrations at baseline. Variability in uremic solute levels was assessed using scatter plots, and limits of variability were calculated. In total, 40 rapidly and 40 slowly progressing patients were included. Uremic solutes were elevated in all patients compared to reference values for healthy persons. The serum levels of uremic solutes were not associated with rapid progression. Moreover, we observed substantial variability in solute levels over time. Elevated concentrations of uremic solutes measured in this study did not explain differences in rate of eGFR decline in CKD patients, possibly due to lack of power as a result of the small sample size, substantial between patient variability, and variability in solute concentrations over time. The etiology of intra-individual variation in uremic solute levels remains to be elucidated.

  20. Projects at the component development and integration facility. Quarterly technical progress report, April 1, 1994--June 30, 1994

    International Nuclear Information System (INIS)

    1994-01-01

    This quarterly technical progress report presents progress on the projects at the Component Development and Integration Facility (CDIF) during the third quarter of FY94. The CDIF is a major Department of Energy test facility in Butte, Montana, operated by MSE, Inc. Projects in progress include: Biomass Remediation Project; Heavy Metal-Contaminated Soil Project; MHD Shutdown; Mine Waste Technology Pilot Program; Plasma Projects; Resource Recovery Project; and Spray Casting Project

  1. Surgical resident technical skill self-evaluation: increased precision with training progression.

    Science.gov (United States)

    Quick, Jacob A; Kudav, Vishal; Doty, Jennifer; Crane, Megan; Bukoski, Alex D; Bennett, Bethany J; Barnes, Stephen L

    2017-10-01

    Surgical resident ability to accurately evaluate one's own skill level is an important part of educational growth. We aimed to determine if differences exist between self and observer technical skill evaluation of surgical residents performing a single procedure. We prospectively enrolled 14 categorical general surgery residents (six post-graduate year [PGY] 1-2, three PGY 3, and five PGY 4-5). Over a 6-month period, following each laparoscopic cholecystectomy, residents and seven faculty each completed the Objective Structured Assessment of Technical Skills (OSATS). Spearman's coefficient was calculated for three groups: senior (PGY 4-5), PGY3, and junior (PGY 1-2). Rho (ρ) values greater than 0.8 were considered well correlated. Of the 125 paired assessments (resident-faculty each evaluating the same case), 58 were completed for senior residents, 54 for PGY3 residents, and 13 for junior residents. Using the mean from all OSATS categories, trainee self-evaluations correlated well to faculty (senior ρ 0.97, PGY3 ρ 0.9, junior ρ 0.9). When specific OSATS categories were analyzed, junior residents exhibited poor correlation in categories of respect for tissue (ρ -0.5), instrument handling (ρ 0.71), operative flow (ρ 0.41), use of assistants (ρ 0.05), procedural knowledge (ρ 0.32), and overall comfort with the procedure (ρ 0.73). PGY3 residents lacked correlation in two OSATS categories, operative flow (ρ 0.7) and procedural knowledge (ρ 0.2). Senior resident self-evaluations exhibited strong correlations to observers in all areas. Surgical residents improve technical skill self-awareness with progressive training. Less-experienced trainees have a tendency to over-or-underestimate technical skill. Copyright © 2017 Elsevier Inc. All rights reserved.

  2. THE USE OF THE PATENT ANALYSIS METHOD FOR FINDING ANALOGUES AND PROTOTYPES OF RECEIVED TECHNICAL SOLUTIONS

    Directory of Open Access Journals (Sweden)

    Irina Petrova

    2016-03-01

    Full Text Available The research deals with the issue of the patent analysis efficiency, which is a necessary stage of seaching analogues and prototypes to obtain technical solutions. The article presents the results of analyzing the present automation systems for finding necessary information in the patent databases and identifies their advantages and disadvantages. It gives a description of the “Intellect” system, which is an example of software systems for the conceptual design stage support. Materials and Methods The article presents some of the possible ways to organize the patents-analogues search process and specific features of searching analogues and prototypes for the generated parametric structure scheme of the technical solution, which is the result of the synthesis of a new information-measuring and control system element in the “Intellect” system. The description of the proposed search query forming method is given. The article gives the structure of the patent passport, which must be stored in a database to organize the process of searcing analogues and prototypes. There given a description of algorithms for automatic adding a patent to the database, recalculating the weights while adding a patent by experts, identifying the fact of using different physical and technical effects in a patent. Results The final part of the article contains an example of the results of testing the developed subsystem implementing the proposed method. According to the test results it is concluded that the selected software and algorithmic solutions are effective.

  3. Nuclear structure theory. Annual technical progress report, July 1, 1975--September 30, 1976

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1976-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: Meson interactions with nucleons and nuclei, including elastic and inelastic scattering of pions, three-body theories of scattering and absorption of pions by deuterons, π-p bremsstrahlung, and multiple-excitation models for meson absorption by heavier nuclei. Studies of the inverse scattering problem including 1 S 0 nucleon-nucleon scattering; the relativistic two-body problem, particularly for relativistic effects at low energies: the unitary-pole expansion in nucleon-nucleon scattering with hard-core interactions. Statistical spectroscopy including: strength distributions and sum rules(both energy weighted and inverse energy weighted) for nuclear excitations; fluctuations and correlations in spectra, strengths and expectation values; studies of Garvey-Kelson and similar mass relationships; spectroscopy in huge spaces including spectral methods for renormalization of the interaction and for using (two + three)-body Skyrme interactions; technical aspects of operator averaging

  4. Power systems development facility. Quarterly technical progress report, January 1, 1994--March 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-01

    This quarterly technical progress report summarizes work completed during the last quarter of the Second Budget Period, January 1 through March 31, 1994, entitled {open_quotes}Hot Gas Cleanup Test Facility for Gasification and Pressurized Combustion.{close_quotes} The objective of this project is to evaluate hot gas particulate control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scale-up of particulate control systems to commercial size.

  5. The U.S. nuclear waste management program - technical progress at Yucca Mountain

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, L.H. [U.S. Department of Energy (United States)

    2001-07-01

    This paper discusses the current status of a national program being developed by the U.S. Department of Energy for the management of spent nuclear fuel and high-level radioactive waste produced by civilian nuclear power generation and defense-related activities. In 1987 the U.S. Congress directed the Department to characterize the Yucca Mountain site in Nevada and determine its suitability for development of a geologic repository. This paper will focus on the technical progress that has been made after more than 15 years of scientific and engineering investigations at Yucca Mountain, and the remaining work that is being done to support a decision on whether to recommend the site for development of a geologic repository. (author)

  6. Technical and legal considerations and solutions in the area of battery charging for electric vehicles

    Science.gov (United States)

    Juda, Z.

    2016-09-01

    The issue of protecting health of residents of urbanized areas from the effect of excessive particulate matter and toxic components of car exhaust gases imposes the need of introduction of clean electric vehicles to the market. The increasing market availability of electric vehicles, especially in the segment of short-range (neighborhood) vehicles is followed by development of new and advanced infrastructure solutions. This also applies to the increasingly popular hybrid vehicles PHEV (Plug-in Hybrid Electric Vehicles). However, problems with the existing designs are primarily associated with limited driving range on a single battery charge, the density of charging stations in urban and suburban area, energy system efficiency due to increased electricity demand and the unification of solutions for charging stations, on-board chargers and the necessary accessories. Technical solutions are dependent on many factors, including the type and size of battery in the vehicle and access to power grid with increased load capacity. The article discusses the legal and technical actions outlined in the above directions. It shows the available and planned solutions in this area.

  7. Progresso tecnico, forme di mercato e disoccupazione. ( Technical progress, market forms and unemployment

    Directory of Open Access Journals (Sweden)

    A. ASIMAKOPULOS A.

    2013-12-01

    Full Text Available Lo scopo del presente lavoro è triplice . Il primo obiettivo è quello di sottolineare l'importanza delle intuizioni da trovare nel lavoro di Sylos Labini . Il secondo scopo è quello di espandere su di essa distinguendo tra i diversi tipi di progresso tecnico . Infine , il terzo obiettivo è quello di commentare il confronto di Labini di Ricardo e Keynes sulla possibilità di disoccupazione tecnologica . Per quanto riguarda la sua descrizione del progresso tecnologico come " risparmio di lavoro " , l'autore mostra che una descrizione più completa sarebbe più utile per i suoi scopiThe purpose of the present paper is threefold. The first purpose is to emphasise the importance of the insights to be found in Sylos Labini’s work. The second purpose is to expand upon it by distinguishing  between the different types of technical progress. Finally, the third purpose is to comment on Labini’s comparison of Ricardo and Keynes on the possibility of technological unemployment. Regarding his description of technological progress as “labour saving”, the author shows that a more comprehensive description would be more useful for his purposes.JEL: E24, J64, O33

  8. Technical solutions for reducing indoor residential exposures to ultrafine particles from second-hand cigarette smoke infiltration

    DEFF Research Database (Denmark)

    Afshari, Alireza; Ardkapan, Siamak Rahimi; Bergsøe, Niels Christian

    2011-01-01

    was carried out in the field in a multi-storey building and cardboard and plastic foil of polyethylene were used for sealing the entire wooden floor in the receiving flat. Another technical solution examined was a novel air circulating ductwork. The efficiency of the novel air circulating ductwork...... in which smoke infiltrates from one flat to another and also to examine technical solutions for preventing or reducing infiltration of ultrafine particles from the source flat to the receiving flat. One of the technical solutions examined was sealing of the floor in the receiving flat. The study...

  9. The effects of environmental regulation and technical progress on CO2 Kuznets curve: An evidence from China

    International Nuclear Information System (INIS)

    Yin, Jianhua; Zheng, Mingzheng; Chen, Jian

    2015-01-01

    Based on environmental Kuznets curve theory, a panel data model which takes environmental regulation and technical progress as its moderating factors was developed to analyse the institutional and technical factors that affect the path of low-carbon economic development. The results indicated that there was a CO 2 emission Kuznets curve seen in China. Environmental regulation had a significant moderating effect on the curve, and the inflection of CO 2 emissions could come substantially earlier under stricter environmental regulation. Meanwhile, the impact of technical progress on the low-carbon economic development path had a longer hysteresis effect but restrained CO 2 emission during its increasing stage and accelerated its downward trend during the decreasing stage which was conducive to emission reduction. Strict environmental regulation could force the high-carbon emitting industries to transfer from the eastern regions to the central or the western regions of China, which would make the CO 2 Kuznets curve higher in its increasing stage and lower in its decreasing stage than that under looser regulation. Furthermore, energy efficiency, energy structure, and industrial structure exerted a significant direct impact on CO 2 emissions; we should consider the above factors as essential in the quest for low-carbon economic development. - Highlights: • Estimate moderating effect of environmental regulation and technical progress on EKC. • There was a CO 2 emission Kuznets curve in effect in China. • Environmental regulation presents significant moderating effect on EKC. • Technical progress moderates the relationship between income and CO 2 emissions

  10. Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

    Energy Technology Data Exchange (ETDEWEB)

    Bender, W.

    2013-01-01

    Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

  11. Generation and focusing of pulsed intense ion beams. Technical progress report, 20 August 1981-30 September 1982

    International Nuclear Information System (INIS)

    Hammer, D.A.; Kusse, B.R.; Sudan, R.N.

    1983-07-01

    The progress on this contract is described in two parts. The first deals with the technical operation of the LION accelerator which is the exact equivalent to one line of PBFA-I. The second part is concerned with the experimental results on the ion diode mounted at the front end of the LION accelerator

  12. Impact of Environmental Regulation and Technical Progress on Industrial Carbon Productivity: An Approach Based on Proxy Measure

    Directory of Open Access Journals (Sweden)

    Huan Zhang

    2016-08-01

    Full Text Available This research aims to study the main influencing factors of China’s industrial carbon productivity by incorporating environmental regulation and technical progress into an econometric model. The paper focuses on data from 35 of China’s industrial sectors and covers the period from 2006 to 2014, in order to examine the impact of environmental regulation and technical progress on carbon productivity. Methods applied include panel fixed effect model, panel random effect model and two stage least squares with instrumental variables (IV-2SLS. The effect of environmental regulation and technical progress has industrial heterogeneity. The paper subdivides industrial sectors into capital and technology intensive, resource intensive and labor intensive sectors according to factor intensiveness. The estimation results of the subgroups have uncovered that for capital and technology intensive and resource intensive sectors, environmental regulation has a more significant impact than technical progress; while for labor intensive sectors, innovation more significantly influences carbon productivity. In addition, foreign direct investment (FDI and industrialization level facilitate improving carbon productivity for the full sample. By contrast, industrial structure inhibits the overall industrial carbon productivity. The industry-specific results indicate that for capital and technology intensive sectors, optimizing of the industrial structure can improve carbon productivity; for resource intensive sectors, FDI and energy consumption structure should be emphasized more; for labor intensive sectors, industrialization levels help enhance carbon productivity. Finally the industrial sector-specific policy suggestions are proposed.

  13. An SNMP-based solution to enable remote ISO/IEEE 11073 technical management.

    Science.gov (United States)

    Lasierra, Nelia; Alesanco, Alvaro; García, José

    2012-07-01

    This paper presents the design and implementation of an architecture based on the integration of simple network management protocol version 3 (SNMPv3) and the standard ISO/IEEE 11073 (X73) to manage technical information in home-based telemonitoring scenarios. This architecture includes the development of an SNMPv3-proxyX73 agent which comprises a management information base (MIB) module adapted to X73. In the proposed scenario, medical devices (MDs) send information to a concentrator device [designated as compute engine (CE)] using the X73 standard. This information together with extra information collected in the CE is stored in the developed MIB. Finally, the information collected is available for remote access via SNMP connection. Moreover, alarms and events can be configured by an external manager in order to provide warnings of irregularities in the MDs' technical performance evaluation. This proposed SNMPv3 agent provides a solution to integrate and unify technical device management in home-based telemonitoring scenarios fully adapted to X73.

  14. PFBC HGCU Test Facility. Technical progress report No. 24, Third quarter, CY 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    This is the twenty-fourth and final Technical Progress Report submitted to the Department of Energy (DOE) in connection with the cooperative agreement between the DOE and Ohio Power Company for the Tidd PFBC Hot Gas Clean Up Test Facility. This report covers the work completed during the Third Quarter of CY 1995. All activity this quarter was directed toward the completion of the program final report. A draft copy of the final report was forwarded to DOE during this quarter, and DOE submitted their comments on the report to AEPSC. DOE requested that Westinghouse write an appendix to the report covering the performance of the fail-safe regenerator devices during Tad operation, and Westinghouse subsequently prepared the appendix. Additional DOE comments were incorporated into the report, and it will be issued in camera-ready form by the end of October, 1995, which is the program end date. Appendix 1 presents the results of filter candle posttest examination by Westinghouse performed on selected filter candles following final shutdown of the system.

  15. New Technical Solution for Vertical Shaft Equipping Using Steel Headframe of Multifunction Purpose

    Science.gov (United States)

    Kassikhina, Elena; Pershin, Vladimir; Glazkov, Yurij

    2017-11-01

    The article reviews a novel approach to the design of steel angle headframe for vertical shafts of coal and ore mines on the basis of rational design solutions. Practice of construction of coal and ore mines provides application of various designs for steel angle headframes which are divided into separate large assembly blocks and constructive elements during assembling operations. Design of these blocks and elements, their weight and dimensions effect the chose of the method of assembling on which economic and technological indicators, as well as duration of down-time, depend on during performance of construction operations in shaft. The technical solution on equipment provision for mine vertical shaft using headframe of multifunctional purpose will allow changing the management construction of vertical shaft. The constructive design of the headgear allows application of the effective method of assembly and thus to provide improvement of the technical and economic indexes, and high calendar time rate of the shaft construction due to reduction of duration of works on equipment provision for the shaft and to refurbishment of the shaft in order to carry out horizontal mining.

  16. Novel technical solutions for wireless ECG transmission & analysis in the age of the internet cloud.

    Science.gov (United States)

    Al-Zaiti, Salah S; Shusterman, Vladimir; Carey, Mary G

    2013-01-01

    Current guidelines recommend early reperfusion therapy for ST-elevation myocardial infarction (STEMI) within 90 min of first medical encounter. Telecardiology entails the use of advanced communication technologies to transmit the prehospital 12-lead electrocardiogram (ECG) to offsite cardiologists for early triage to the cath lab; which has been shown to dramatically reduce door-to-balloon time and total mortality. However, hospitals often find adopting ECG transmission technologies very challenging. The current review identifies seven major technical challenges of prehospital ECG transmission, including: paramedics inconvenience and transport delay; signal noise and interpretation errors; equipment malfunction and transmission failure; reliability of mobile phone networks; lack of compliance with the standards of digital ECG formats; poor integration with electronic medical records; and costly hardware and software pre-requisite installation. Current and potential solutions to address each of these technical challenges are discussed in details and include: automated ECG transmission protocols; annotatable waveform-based ECGs; optimal routing solutions; and the use of cloud computing systems rather than vendor-specific processing stations. Nevertheless, strategies to monitor transmission effectiveness and patient outcomes are essential to sustain initial gains of implementing ECG transmission technologies. © 2013.

  17. Foundations for technical solutions in organizing excavation of open ore pits

    Directory of Open Access Journals (Sweden)

    С. И. Фомин

    2016-11-01

    Full Text Available To study stochastic mining technical systems of opencast mines, where parallel to clearly defined values random and indefinite factors operate, probabilistic and statistical techniques are mostly used nowadays. Formally, the task of producing a design solution may, under the conditions of indeterminacy be transformed into an equivalent deterministic problem formulated for a risky situation. Uncertainty in the initial mining, geological and technical-economic information available during the design stage may result in changing the principal output characteristics of the opencast mine and undermine its operational efficiency during its exploitation. Lowering the possible economic losses is then possible via designing a stable technological  system. To minimize the degree of indeterminacy one first of all needs to identify the area of potential risk, define the probability of its emergence and assess its potential consequences. In case such consequences may be precluded, a clearer more complete understanding of the problem would promote a better thought through reaction to potential risk in the course of implementing design solutions.

  18. Efficiency potential of management and technical solutions for a construction object

    Directory of Open Access Journals (Sweden)

    Lapidus Azariy Abramovich

    2014-01-01

    Full Text Available The authors investigate the models of efficiency potential of management and technical solutions for a construction object, which allows accounting for the influence of management-technological and administrative solutions in the process of implementing construction project. The solutions are represented by various factors – solitary integral potentials. The factors, which should be taken into account in the process of developing an integral model, are: development of general contracting structure, project decisions, management decisions, administrative decisions and ecological impact. In is necessary to develop the model, which will integrally put together the above mentioned factors of a construction project, observe and investigate other factors, create a model and get the opportunity not only to predict the endpoint of the future construction object on the stage of formulating technological requirements, but also to monitor the changes of this prognosis in time. The parameters of the integral potential will allow the system to obtain flexibility, which makes it possible to adjust to the changes usually taking place on a construction object and at the same time to aim for optimization of organizational, technological and administrative solutions in the process of reaching endpoint of construction.

  19. Technical solutions for the attenuation of the occupational noxeses at the workplaces

    International Nuclear Information System (INIS)

    Raducanu, Alice; Stanca, Angela; Pop, Ovidiu

    2004-01-01

    A number of workplaces where the employees work under noxesious environment exist within the thermal power plants. The infliction of the working environment has more or less detrimental effect upon the personnel exposed depending on the existing noxeses' toxicity, the concentration, exposure duration, and constitution of the subjects exposed. At present, a number of specific measures have been taken in the power generation sector in order to limit or eliminate the noxeses, with a view to prevent the employees to fall ill, however these measures gave not the expected efficiency. The survey of the workplaces has aimed at transforming the risks into either non-risks or lower risks through the cognition of the noxesious factors (and the risks due to them) existing in the zone of the workplaces and through the cognition of the measures specific for the individual and collective protection, and, the last but not the least, the cognition of the measures required to reduce, eliminate and prevent them. Identification of the places with a high noxesious level and, the preparing of the technical-organisational solutions for the improvement of the physical and chemical noxeses exhaustion and elimination, including also the impact of their application financial costs represent all factors of major importance for lining up the occupational noxeses levels with the national and European standards. This paper describes the evaluation of a real situation by help of the modern methodologies for the identification and monitoring of the physical and chemical noxeses from two Romanian thermal power plants, the analysis of the Health condition for the employees exposed to such physical and chemical noxeses and it establishes, in the end, the risks of the occupational exposure. Further on, the main technical solutions for the diminishing or elimination of the occupational noxeses at the workplaces from the thermal power plants are described. These solutions consist of various types of

  20. Technical Challenge and Demonstration of Advanced Solution Monitoring and Measurement System (ASMS)

    International Nuclear Information System (INIS)

    Takaya, A.; Mukai, Y.; Nakamura, H.; Hosoma, T.; Yoshimoto, K.; Tamura, T.; Iwamoto, T.

    2010-01-01

    JNFL and JAEA have collaboratively started to develop an Advanced Solution Measurement and monitoring System (ASMS) as a part of technical challenge intended for next generation safeguards NDA equipment. After we completed feasibility study by using small detectors, the second stage of ASMS has installed into PCDF tank located in a cell, and then tested and calibrated by Pu nitrate solution experimentally. There was no experience measuring around 50kg Pu inventory directly, so it was very challenging work. The conventional SMMS (Solution Monitoring and Measurement System) that is composed of precision manometers acquires density, level and temperature of solution, so that the sampling and analysis are essential to obtain the nuclear material amount in the tank. The SMMS has two weak points on verification and monitoring of the nuclear material flow and inventory; (1) Direct measurement of the inventory cannot be done, (2) Solution rework and reagent adjustment operation in actual plant will make miss-interpretation on the monitoring evaluation. The purpose of ASMS development is to establish quantitative plutonium mass measurement technique directly by NDA of high concentrated pure plutonium nitrate solution and monitoring capability for solution transfers in a process. The merits of ASMS are considered below; (1) Provide direct Pu measurement and continuous monitoring capability, (2) Eliminate sampling and analysis at IIV, (3) Reduce unmeasured inventory. The target of the measurement uncertainty of ASMS is set less than 6% (1sigma) which is equivalent to meet the detection level of the partial defect at IIV by NDA. Known-alpha coincidence counting technique is applied to the ASMS, which is similar to the NDAs for MOX powder as a principle measurement technique. Especially, three following points are key techniques to establish ASMS. (1) Pre-determination of plutonium isotopic composition because it impacts alpha and rho-zero values to obtain multiplication

  1. Power systems development facility. Quarterly technical progress report, July 1--September 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-31

    This quarterly technical progress report summarizes work completed during the Second Quarter of the Second Budget Period, July 1 through September 30, 1993, under the Department of Energy (DOE) Cooperative Agreement No. DE-FC21-90MC25140 entitled ``Hot Gas Cleanup Test Facility for Gasification and Pressurized Combustion.`` The objective of this project is to evaluate hot gas particle control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scaleup of particulate control systems to commercial size. The conceptual design of the facility was extended to include a within scope, phased expansion of the existing Hot Gas Cleanup Test Facility Cooperative Agreement to also address systems integration issues of hot particulate removal in advanced coal-based power generation systems. This expansion included the consideration of the following modules at the test facility in addition to the existing Transport Reactor gas source and Hot Gas Cleanup Units: Carbonizer/Pressurized Circulating Fluidized Bed Gas Source. Hot Gas Cleanup Units to mate to all gas streams; Combustion Gas Turbine; and Fuel Cell and associated gas treatment. This expansion to the Hot Gas Cleanup Test Facility is herein referred to as the Power Systems Development Facility (PSDF). The major emphasis during this reporting period was continuing the detailed design of the facility.

  2. Instrumentation of dynamic gas pulse loading system. Technical progress report, first quarter 1992

    Energy Technology Data Exchange (ETDEWEB)

    Mohaupt, H.

    1992-04-14

    The overall goal of this work is to further develop and field test a system of stimulating oil and gas wells, which increases the effective radius of the well bore so that more oil can flow into it, by recording pressure during the gas generation phase in real time so that fractures can be induced more predictably in the producing formation. Task 1: Complete the laboratory studies currently underway with the prototype model of the instrumentation currently being studied. Task 2: Perform field tests of the model in the Taft/Bakersfield area, utilizing operations closest to the engineers working on the project, and optimize the unit for various conditions encountered there. Task 3: Perform field test of the model in DGPL jobs which are scheduled in the mid-continent area, and optimize the unit for downhole conditions encountered there. Task 4: Analyze and summarize the results achieved during the complete test series, documenting the steps for usage of downhole instrumentation in the field, and compile data specifying use of the technology by others. Task 5: Prepare final report for DOE, and include also a report on the field tests completed. Describe and estimate the probability of the technology being commercialized and in what time span. The project has made substantial technical progress, though we are running about a month behind schedule. Expenditures are in line with the schedule. Increased widespread interest in the use of DGPL stimulation has kept us very busy. The computer modeling and test instrumentation developed under this program is already being applied to commercial operations.

  3. Recent progress in solution plasma-synthesized-carbon-supported catalysts for energy conversion systems

    Science.gov (United States)

    Lun Li, Oi; Lee, Hoonseung; Ishizaki, Takahiro

    2018-01-01

    Carbon-based materials have been widely utilized as the electrode materials in energy conversion and storage technologies, such as fuel cells and metal-air batteries. In these systems, the oxygen reduction reaction is an important step that determines the overall performance. A novel synthesis route, named the solution plasma process, has been recently utilized to synthesize various types of metal-based and heteroatom-doped carbon catalysts. In this review, we summarize cutting-edge technologies involving the synthesis and modeling of carbon-supported catalysts synthesized via solution plasma process, followed by current progress on the electrocatalytic performance of these catalysts. This review provides the fundamental and state-of-the-art performance of solution-plasma-synthesized electrode materials, as well as the remaining scientific and technological challenges for this process.

  4. Nuclear structure theory. Technical progress report, September 1, 1984-August 31, 1985

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1985-01-01

    This report summarizes progress in the following areas of research: Spectral Averaging, including the theory of level densities and partition functions for interacting nucleons, spectral distributions for fixed symmetries, general studies of distributions (in particular of strength distributions) considered as multivariate processes, and applications to the secular behavior of fluctuation measures; spectral and strength fluctuations, including study of the transitions between different fluctuation patterns (i.e., between different types of quantum chaos) as a conserved symmetry is gradually broken, application of these results to determining values of, or upper bounds for, the goodness of symmetries in complex nuclei, reduction of values or bounds to statements about the nuclear Hamiltonian, in particular for time-reversal symmetry, and specific studies of quantum chaos; statistical theory of pion absorption, including analysis of the (π,p) inclusive reaction; and quark theory of nuclear matter, involving development of models which show two limiting behaviors - that of a Fermi gas of nucleons (quark clusters) at low density and of a Fermi gas of quarks at high density. Both variational and exact solutions of one model have been found. 9 refs

  5. Nuclear structure theory: Technical progress report for period September 1, 1986-August 31, 1987

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1987-08-01

    This report summarizes progress in the following areas of research: (1) quark theory of nuclear matter, including further development of models in one-dimension with analytic solutions, numerical studies, bound properties, inclusion of spin and isospin degrees of freedom, excitation properties and response function; electron scattering, including application of sum rules to deeply inelastic scattering, and of quark models of nuclei; charge exchange in pion-nucleus reactions, including models of isotensor optical potential, optical theorem for double charge exchange, and coupled-channel calculations of single charge exchange; a unified theory of reaction dynamics and nuclear structure for intermediate energies, including diagrammatic formulation and development of appropriate computer programs; weak interactions: a study of the neutrino mass-matrix; bounds for time reversal noninvariance in the nucleon-nucleon interaction, obtained from spectral and strength fluctuations in complex nuclei, and separately from detailed balance in compound nuclear reactions. The relative sensitivities of the two methods are discussed; fluctuation measures for the two-dimensional harmonic oscillator; random matrices and symmetry-breaking in atomic spectra data; saturation effects for spectral measures in many-particle systems; and finally fluctuation-free statistical spectroscopy, applied to state densities and partition functions, including accurate absolute calculations of nuclear level spacings

  6. Savannah River Plant, Works Technical Department monthly progress report for March 1956

    International Nuclear Information System (INIS)

    1956-01-01

    This document details activities of the Works Technical Department during the month of March 1956. It covers reactor technology, separations technology, engineering assistance and heavy water technology

  7. Decomposing productivity growth allowing efficiency gains and price-induced technical progress

    NARCIS (Netherlands)

    Oude Lansink, A.G.J.M.; Silva, E.; Stefanou, S.

    2000-01-01

    Time- and firm-specific output technical efficiency measures are generated within a price-induced technological change framework. The firm-specific production frontier incorporates past prices as an argument encouraging innovation and a time trend to account for exogenous technical change. The

  8. Optimal design and routing of power lines; ecological, technical and economic perspectives (OPTIPOL). Progress report 2009

    Energy Technology Data Exchange (ETDEWEB)

    Bevanger, K.; Bartzke, G.; Broeseth, H.; Gjershaug, J.O.; Hanssen, F.; Jacobsen, K.-O.; Kvaloey, P.; May, R.; Nygaard, T.; Pedersen, H.C.; Reitan, O.; Refsnaes, S.; Stokke, S.; Vang, R.

    2009-12-15

    From 2009 inclusive, NINA has received economic support for research on power lines and wildlife from the Norwegian Research Council (NFR) through the RENERGI Programme. The project is named 'Optimal design and routing of power lines; ecological, technical and economic perspectives' (OPTIPOL). It is scheduled for 5 years (2009-1013) and is part of the activities within CEDREN, i.e. the Centre for environmental design of renewable energy (cf. http://www.cedren.no). With a grid close to 200 000 km overhead power-lines, the associated rights-of-way (ROW) affect huge land areas in Norway. The overall goal is to develop predict-ing tools for optimal routing of power lines from an environmental perspective and assess technical and economic solutions to minimize conflicts with wildlife and habitat conservation. Thus, the OPTIPOL rationale is based on the belief that the negative effects of electricity transmission and distribution can be reduced with respect to birds and mammals. OPTIPOL has several ambitious objectives, and is divided into sub-projects and specific tasks. From the first of November a PhD-student became part of the project, a position that will be held for 4 years. The main objective of the PhD-activities will be to assess how and why different wildlife species use deforested areas below power lines, evaluate possible positive and negative effects of power-line ROWs, and assess the possibilities for quality improvement. Another part of the project is dedicated the effects of linear structures on movement patterns and distribution in the landscape in native deer species. Here we will examine how different spatial scales influence the processes that guide movement patterns, and responses to linear structures. Another focus will be small game species, with mountain hare, capercaillie, black grouse and hazel grouse as model species. The main objective will be to assess the impact of transforming ROW habitats into attractive small-game foraging

  9. DISPOWER. A socio-economic analysis of technical solutions and practices for the integration of distributed generation

    International Nuclear Information System (INIS)

    Ten Donkelaar, M.; Scheepers, M.J.J.

    2004-07-01

    Socio-economic impacts of technical solutions and approaches that are being developed for the integration of distributed generation (DG) in electricity distribution systems are analyzed. For this analysis an inventory was made of technical options, solutions and approaches on the basis of a questionnaire that has been distributed among DG (technical) experts. The questionnaire was not meant to give an exhaustive overview, but to gain insight in the possible technical solutions, options and approaches and the economic interactions between different actors in the electricity market. The different technical options and solutions have been divided into four main categories. Four technologies, one of each category, have been studied in more detail to analyse their impact on the financial relationships between the actors in the distribution network. The four technologies are: wind power prediction tool (planning tool), grid control unit (power quality device), power operation and power quality management system (ICT device), and power storage device. To assess the impact of the investments in the proposed technologies on all actors involved (and different from the actor investing), an assessment tool has been developed to qualitatively identify the economic impacts of a number of these options. This assessment tool takes into account the financial transactions between the parties on the distribution network. The analysis also discusses the allocation of the economic value of certain benefits through contracts and economic network regulation

  10. Hydrogen production by supercritical water gasification of biomass. Phase 1 -- Technical and business feasibility study, technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    The nine-month Phase 1 feasibility study was directed toward the application of supercritical water gasification (SCWG) for the economical production and end use of hydrogen from renewable energy sources such as sewage sludge, pulp waste, agricultural wastes, and ultimately the combustible portion of municipal solid waste. Unique in comparison to other gasifier systems, the properties of supercritical water (SCW) are ideal for processing biowastes with high moisture content or contain toxic or hazardous contaminants. During Phase I, an end-to-end SCWG system was evaluated. A range of process options was initially considered for each of the key subsystems. This was followed by tests of sewage sludge feed preparation, pumping and gasification in the SCW pilot plant facility. Based on the initial process review and successful pilot-scale testing, engineering evaluations were performed that defined a baseline system for the production, storage and end use of hydrogen. The results compare favorably with alternative biomass gasifiers currently being developed. The results were then discussed with regional wastewater treatment facility operators to gain their perspective on the proposed commercial SCWG systems and to help define the potential market. Finally, the technical and business plans were developed based on perceived market needs and the projected capital and operating costs of SCWG units. The result is a three-year plan for further development, culminating in a follow-on demonstration test of a 5 MT/day system at a local wastewater treatment plant.

  11. Coal to SNG: Technical progress, modeling and system optimization through exergy analysis

    International Nuclear Information System (INIS)

    Li, Sheng; Ji, Xiaozhou; Zhang, Xiaosong; Gao, Lin; Jin, Hongguang

    2014-01-01

    Highlights: • Technical progresses of coal to SNG technologies are reported. • The entire coal to SNG system is modeled. • Coupling between SNG production and power generation is investigated. • Breakthrough points for further energy saving are determined. • System performance is optimized based on the first and second laws of thermodynamics. - Abstract: For both energy security and CO 2 emission reduction, synthetic natural gas (SNG) production from coal is an important path to implement clean coal technologies in China. In this paper, an overview of the progress of coal to SNG technologies, including the development of catalysts, reactor designs, synthesis processes, and systems integration, is provided. The coal to SNG system is modeled, the coupling between SNG production and power generation is investigated, the breakthrough points for further energy savings are determined, and the system performance is optimized based on the first and the second laws of thermodynamics. From the viewpoint of the first law of thermodynamics, the energy conversion efficiency of coal to SNG system can reach 59.8%. To reduce the plant auxiliary power, the breakthrough points are the development of low-energy-consumption oxygen production technology and gas purification technology or seeking new oxidants for coal gasification instead of oxygen. From the viewpoint of the second law of thermodynamics, the major exergy destruction in a coal to SNG system occurs in the coal gasification unit, SNG synthesis unit and the raw syngas cooling process. How to reduce the exergy destruction in these units is the key to energy savings and system performance enhancement. The conversion ratio of the first SNG synthesis reactor and the split ratio of the recycle gas are key factors that determine the performance of both the SNG synthesis process and the whole plant. A “turning point” phenomenon is observed: when the split ratio is higher than 0.90, the exergy destruction of the SNG

  12. Technical Report: Unmanned Helicopter Solution for Survey-Grade Lidar and Hyperspectral Mapping

    Science.gov (United States)

    Kaňuk, Ján; Gallay, Michal; Eck, Christoph; Zgraggen, Carlo; Dvorný, Eduard

    2018-05-01

    Recent development of light-weight unmanned airborne vehicles (UAV) and miniaturization of sensors provide new possibilities for remote sensing and high-resolution mapping. Mini-UAV platforms are emerging, but powerful UAV platforms of higher payload capacity are required to carry the sensors for survey-grade mapping. In this paper, we demonstrate a technological solution and application of two different payloads for highly accurate and detailed mapping. The unmanned airborne system (UAS) comprises a Scout B1-100 autonomously operating UAV helicopter powered by a gasoline two-stroke engine with maximum take-off weight of 75 kg. The UAV allows for integrating of up to 18 kg of a customized payload. Our technological solution comprises two types of payload completely independent of the platform. The first payload contains a VUX-1 laser scanner (Riegl, Austria) and a Sony A6000 E-Mount photo camera. The second payload integrates a hyperspectral push-broom scanner AISA Kestrel 10 (Specim, Finland). The two payloads need to be alternated if mapping with both is required. Both payloads include an inertial navigation system xNAV550 (Oxford Technical Solutions Ltd., United Kingdom), a separate data link, and a power supply unit. Such a constellation allowed for achieving high accuracy of the flight line post-processing in two test missions. The standard deviation was 0.02 m (XY) and 0.025 m (Z), respectively. The intended application of the UAS was for high-resolution mapping and monitoring of landscape dynamics (landslides, erosion, flooding, or crops growth). The legal regulations for such UAV applications in Switzerland and Slovakia are also discussed.

  13. Current Progress in Solution Precursor Plasma Spraying of Cermets: A Review

    Directory of Open Access Journals (Sweden)

    Romnick Unabia

    2018-06-01

    Full Text Available Ceramic and metal composites, known also as cermets, may considerably improve many material properties with regards to that of initial components. Hence, cermets are frequently applied in many technological fields. Among many processes which can be employed for cermet manufacturing, thermal spraying is one of the most frequently used. Conventional plasma spraying of powders is a popular and cost-effective manufacturing process. One of its most recent innovations, called solution precursor plasma spraying (SPPS, is an emerging coating deposition method which uses homogeneously mixed solution precursors as a feedstock. The technique enables a single-step deposition avoiding the powder preparation procedures. The nanostructured coatings developed by SPPS increasingly find a place in the field of surface engineering. The present review shows the recent progress in the fabrication of cermets using SPPS. The influence of starting solution precursors, such as their chemistry, concentration, and solvents used, to the micro-structural characteristics of cermet coatings is discussed. The effect of the operational plasma spray process parameters such as solution injection mode to the deposition process and coatings’ microstructure is also presented. Moreover, the advantages of the SPPS process and its drawbacks compared to the conventional powder plasma spraying process are discussed. Finally, some applications of SPPS cermet coatings are presented to understand the potential of the process.

  14. Savannah River Plant Works Technical Department monthly progress report for May 1958: Deleted Version

    Energy Technology Data Exchange (ETDEWEB)

    1958-06-17

    This progress report by the Atomic Energy Division of the Savannah River Plant covers: Reactor Technology; Separation Technology; Engineering Assistance; Health Physics; and General Laboratory Work. (JT)

  15. A Simple extension of Dematerialization Theory: Incorporation of Technical Progress and the Rebound Effect

    OpenAIRE

    Magee, Christopher L.; Devezas, Tessaleno C.

    2016-01-01

    Dematerialization is the reduction in the quantity of materials needed to produce something useful over time. Dematerialization fundamentally derives from ongoing increases in technical performance but it can be counteracted by demand rebound - increases in usage because of increased value (or decreased cost) that also results from increasing technical performance. A major question then is to what extent technological performance improvement can offset and is offsetting continuously increasin...

  16. Inkjet-Printed Chemical Solution Y2O3 Layers for Planarization of Technical Substrates

    Directory of Open Access Journals (Sweden)

    Marta Vilardell

    2017-12-01

    Full Text Available The implementation of the Chemical Solution Deposition (CSD methodology with the Drop on Demand (DoD inkjet printing (IJP technology has been successfully employed to develop a Solution Deposition Planarization (SDP method. We have used nanocrystalline yttrium oxide (Y2O3 to decrease the roughness of technical metallic substrates by filling the surface imperfections and thus avoiding costly polishing steps. This alternative process represents an outstanding methodology to reduce the final cost of the second-generation coated conductors manufacturing. Two Y2O3 metalorganic precursor ink formulations were successfully developed and tested to obtain surfaces as smooth as possible with adequate mechanical properties to hold the internal stress developed during the growth of the subsequent layers. By using these inks as precursors for IJP and after a proper tuning of the rheological and wetting parameters, we firstly obtained centimeter length uniform 100 nm-thick SDP-Y2O3 films on unpolished stainless-steel substrate from Bruker HTS. The scalability of the roll to roll (R2R-IJP process to 100 m is then demonstrated on metallic substrates as well. A complete characterization of the prepared SDP-Y2O3 inkjet-printed layers was carried out using optical microscopy, FIB-SEM (Focus Ion Beam coupled to Scanning Electron Microscopy, XRD (X-ray Diffraction, AFM (Atomic Force Microscopy, reflectometry and nanoindentation techniques. Then, the morphology, thickness, crystallinity and mechanical properties were evaluated, together with the surface roughness in order to assess the resulting layer planarity. The impact of planarity was additionally studied via growth of biaxially textured buffer layers as well as further functional layers. 1.1 µm-thick YSZ layers with in-plane textures better than the stainless steel (SS polished reference were successfully deposited on top of 100 nm SDP-Y2O3 films yielding 50% of Ic in contrast to the standard SS reference.

  17. The Impacts of Technical Progress on Sulfur Dioxide Kuznets Curve in China: A Spatial Panel Data Approach

    Directory of Open Access Journals (Sweden)

    Zhimin Zhou

    2017-04-01

    Full Text Available This paper aims to reveal the nexus for sulfur dioxide (SO2 emission and income, as well as the effects of technical progress on SO2 emission in China based on environment Kuznets curve (EKC hypothesis. The spatial panel technique is used in case the coefficient estimates are biased due to the negligence of spatial dependence. With the provincial panel data of China from 2004 to 2014, this is the first research that finds an inverse N-trajectory of the relationship between SO2 emission and economic growth and confirms the beneficial impacts of technical advancement on SO2 emission abatement. The empirical results also suggest that the industrial structure change is an important driving force of the SO2 EKC. In addition, the direct and spillover effects of determinants on sulfur emission are clarified and estimated by a correct approach. Finally, we check the stability of our conclusions on the EKC shape for SO2 and technical progress effects when controlling for different variables and specifications, through which we find the turning points are sensitive to variables selections.

  18. Savannah River Ecology Laboratory, Annual Technical Progress Report of Ecological Research, June 30, 2002

    Energy Technology Data Exchange (ETDEWEB)

    Paul M. Bertsch, (Director)

    2002-06-30

    The Savannah River Ecology Laboratory (SREL) is a research unit of The University of Georgia (UGA) and has been conducting ecological research on the Savannah River Site (SRS) near Aiken, South Carolina for 50 years. The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts fundamental and applied ecological research, as well as education and outreach programs, under a Cooperative Agreement with the U.S. Department of Energy (DOE). The Laboratory's research mission during the 2002 fiscal year was fulfilled with the publication of 76 journal articles and book chapters by faculty, technical staff, students, and visiting scientists. An additional 50 journal articles have been submitted or are in press. Other noteworthy events took place as faculty members, staff, and graduate students received awards. These are described in the section titled Special Accomplishments of Faculty, Staff, Students, and Administration on page 51. Notable scientific accomplishments include work conducted on contaminant transport, stable isotopes, sandhills ecology, and phytoremediation: (1) A collaborative study between Dr. Tom Hinton at SREL and scientists at SRTC demonstrated the feasibility of using illite clay to sequester 137Cs in sediments along the P and R reactor cooling canal system, where approximately 3,000 acres of land are contaminated. Overall, the study showed significant decreases in cesium concentrations and bioavailability following the addition of illite with no sign of harm to the ecosystem. While the cesium remains sequestered from the biosphere, its radioactivity decays and the process progresses from contaminant immobilization to remediation. (2) SREL's stable isotope laboratory is now fully functional. Stable isotope distributions in nature can provide important insights into many historical and current environmental processes. Dr. Christopher Romanek is leading SREL's research

  19. High-Efficiency Nitride-Based Solid-State Lighting. Final Technical Progress Report

    International Nuclear Information System (INIS)

    Paul T. Fini; Shuji Nakamura

    2005-01-01

    In this final technical progress report we summarize research accomplished during Department of Energy contract DE-FC26-01NT41203, entitled ''High-Efficiency Nitride-Based Solid-State Lighting''. Two teams, from the University of California at Santa Barbara (Principle Investigator: Dr. Shuji Nakamura) and the Lighting Research Center at Rensselaer Polytechnic Institute (led by Dr. N. Narendran), pursued the goals of this contract from thin film growth, characterization, and packaging/luminaire design standpoints. The UCSB team initially pursued the development of blue gallium nitride (GaN)-based vertical-cavity surface-emitting lasers, as well as ultraviolet GaN-based light emitting diodes (LEDs). In Year 2, the emphasis shifted to resonant-cavity light emitting diodes, also known as micro-cavity LEDs when extremely thin device cavities are fabricated. These devices have very directional emission and higher light extraction efficiency than conventional LEDs. Via the optimization of thin-film growth and refinement of device processing, we decreased the total cavity thickness to less than 1 (micro)m, such that micro-cavity effects were clearly observed and a light extraction efficiency of over 10% was reached. We also began the development of photonic crystals for increased light extraction, in particular for so-called ''guided modes'' which would otherwise propagate laterally in the device and be re-absorbed. Finally, we pursued the growth of smooth, high-quality nonpolar a-plane and m-plane GaN films, as well as blue light emitting diodes on these novel films. Initial nonpolar LEDs showed the expected behavior of negligible peak wavelength shift with increasing drive current. M-plane LEDs in particular show promise, as unpackaged devices had unsaturated optical output power of ∼ 3 mW at 200 mA drive current. The LRC's tasks were aimed at developing the subcomponents necessary for packaging UCSB's light emitting diodes, and packaging them to produce a white light

  20. Savannah River Ecology Laboratory, Annual Technical Progress Report of Ecological Research, June 30, 2002

    International Nuclear Information System (INIS)

    Paul M. Bertsch,

    2002-01-01

    The Savannah River Ecology Laboratory (SREL) is a research unit of The University of Georgia (UGA) and has been conducting ecological research on the Savannah River Site (SRS) near Aiken, South Carolina for 50 years. The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts fundamental and applied ecological research, as well as education and outreach programs, under a Cooperative Agreement with the U.S. Department of Energy (DOE). The Laboratory's research mission during the 2002 fiscal year was fulfilled with the publication of 76 journal articles and book chapters by faculty, technical staff, students, and visiting scientists. An additional 50 journal articles have been submitted or are in press. Other noteworthy events took place as faculty members, staff, and graduate students received awards. These are described in the section titled Special Accomplishments of Faculty, Staff, Students, and Administration on page 51. Notable scientific accomplishments include work conducted on contaminant transport, stable isotopes, sandhills ecology, and phytoremediation: (1) A collaborative study between Dr. Tom Hinton at SREL and scientists at SRTC demonstrated the feasibility of using illite clay to sequester 137Cs in sediments along the P and R reactor cooling canal system, where approximately 3, 000 acres of land are contaminated. Overall, the study showed significant decreases in cesium concentrations and bioavailability following the addition of illite with no sign of harm to the ecosystem. While the cesium remains sequestered from the biosphere, its radioactivity decays and the process progresses from contaminant immobilization to remediation. (2) SREL's stable isotope laboratory is now fully functional. Stable isotope distributions in nature can provide important insights into many historical and current environmental processes. Dr. Christopher Romanek is leading SREL's research in this area

  1. Telemetry system for monitoring the ECG for patients with high cardiovascular risk. Main design requirements and technical solutions

    International Nuclear Information System (INIS)

    Rodriguez, J; Meissimilly, G; Berovides, JD

    2005-01-01

    In this paper the main design requirements concerning the setting up of a telemetry ECG monitoring system are presented. The design's most important technical solutions as well as some details are also discussed. This system is intended to provide skilled medical assistance during the cardiac rehabilitation of both asymptomatic and high risk coronary patients

  2. Exploring technological and architectural solutions for nursing home residents, care professionals and technical staff: Focus groups with professional stakeholders.

    OpenAIRE

    Dooremalen, A.M.C.; van Hoof, J.; Weffers, H.T.G.; Wetzels, M.H.; Wouters, E.J.M.

    2014-01-01

    J. van Hoof, A.M.C. Dooremalen, M.H. Wetzels, H.T.G. Weffers, E.J.M. Wouters (2014) Exploring technological and architectural solutions for nursing home residents, care professionals and technical staff: Focus groups with professional stakeholders. International Journal for Innovative Research in Science & Technology 1(3): 90-105

  3. Exploring technological and architectural solutions for nursing home residents, care professionals and technical staff: Focus groups with professional stakeholders.

    NARCIS (Netherlands)

    A.M.C. Dooremalen; J. van Hoof; H.T.G. Weffers; M.H. Wetzels; MD E.J.M. Wouters

    2014-01-01

    J. van Hoof, A.M.C. Dooremalen, M.H. Wetzels, H.T.G. Weffers, E.J.M. Wouters (2014) Exploring technological and architectural solutions for nursing home residents, care professionals and technical staff: Focus groups with professional stakeholders. International Journal for Innovative Research in

  4. Technical Solution for Protection of Heat Pump Evaporators Against Freezing the Moisture Condensed

    Directory of Open Access Journals (Sweden)

    Vasilyev Gregory P.

    2016-01-01

    Full Text Available This article is dedicated to the study of the processes of formation and freezing of condensate in heat exchangers using ambientair heat and is prepared according to the results of experimental investigations. The aim of this work has been set to elaboratean energy-independent technical solution for protection of heat-exchange equipment against freezing the moisture condensed on the heat-exchange surfaces while using the low-potential heat of ambient air in heat pump systems. The investigations have shown that at the temperatures of ambient air close to 0°C when using the «traditional» way of defrostation, which means the reverse mode of operation of heat pump, an intensive formation of ice is observed at the bottom part of evaporator (if not provided with tray heater. This effect is provoked by downward flow of thawed water and it’s freezing in the lower part of the heat-exchanger due to the fact that the tray and housing of heat pump have a temperature below zero. Thereafter, while the defrostation mode has been periodically used, the ice coat would be going to continue its growth, and by time significant area of evaporator could appear to be covered with ice. The results of the investigations presented in the article could be applied both to air-source heat pumps and to ventilation air heat recuperators.

  5. TECHNICAL SOLUTIONS FOR MODELING PANTS PATTERNS IN CORRESPONDENCE WITH WOMEN'S CONFORMATIONAL PARTICULARITIES

    Directory of Open Access Journals (Sweden)

    Sabina Olaru

    2013-01-01

    Full Text Available The geometric method used in patterns design of different products categories, gives good results for garments manufacturing in industrial system, meaning type representative bodies. The quality of the results is due to the fact that in geometric method the completion of the basic patterns is achieved by prototype implementation followed by viewing the correspondence between the body and the garment, by dressing the human body or industrial mannequin. In the case that the garment, designed and manufactured for type representative bodies according to the standards is dressed by persons that do not fit the type bodies for whom the product was made, the fenomena called “draping defects” apprears. These unconcordances between wearer body and product obtained in industrial system is due to the conformational features of potential users such as: buttocks prominence and form, hips prominence and form, pelvis width and length, ratio between front and anterior-posterior diameters of the pelvis.Anthropometry researches have shown that for a standardized value of the hip perimeter the secondary dimensions of the area (posterior buttock arch, length from waist the buttock point, lower arch of torso may have different values. In this context, the paper aims to analyze the shape and size of the women’s pelvis and to develop the technical solutions to adapt the basic pattern for “trousers with adjusted silhouette” to concrete particularities of the body shape.

  6. Toward cardiovascular MRI at 7 T: clinical needs, technical solutions and research promises

    International Nuclear Information System (INIS)

    Niendorf, Thoralf; Sodickson, Daniel K.; Krombach, Gabriele A.; Schulz-Menger, Jeanette

    2010-01-01

    To consider potential clinical needs, technical solutions and research promises of ultrahigh-field strength cardiovascular MR (CMR). A literature review is given, surveying advantages and disadvantages of CMR at ultrahigh fields (UHF). Key concepts, emerging technologies, practical considerations and applications of UHF CMR are provided. Examples of UHF CMR imaging strategies and their added value are demonstrated, including the numerous unsolved problems. A concluding section explores future directions in UHF CMR. UHF CMR can be regarded as one of the most challenging MRI applications. Image quality achievable at UHF is not always exclusively defined by signal-to-noise considerations. Some of the inherent advantages of UHF MRI are offset by practical challenges. But UHF CMR can boast advantages over its kindred lower field counterparts by trading the traits of high magnetic fields for increased temporal and/or spatial resolution. CMR at ultrahigh-field strengths is a powerful motivator, since speed and signal may be invested to overcome the fundamental constraints that continue to hamper traditional CMR. If practical challenges can be overcome, UHF CMR will help to open the door to new approaches for basic science and clinical research. (orig.)

  7. Practical technical solution for clay-contaminated sands used in concrete

    Directory of Open Access Journals (Sweden)

    Estephane Pierre

    2017-01-01

    Full Text Available Sand, whether natural or manufactured, shows in many instances varying degrees of high levels of clay contamination. This fact is encountered in different parts of the globe and can lead to serious problems in adjusting concrete mix proportions and requiring high water to cement ratios and/or high dosages of superplasticizers without necessarily meeting the workability requirements, even when the sand is previously washed with fresh water. In this paper, different types of sand from the Gulf Cooperation Council (GCC region are being screened, analysed for their clay contents and consequent effects on plastic concrete quality. A technical solution is being proposed based on engineered superplasticizers. A testing protocol has been established to verify the robustness of optimized mix designs demonstrating the performance of the admixture in terms of initial and extended workability. In particular, it will be demonstrated that the customized concrete admixtures constitute by themselves a stand-alone answer to the usage of clay-contaminated sands in concrete.

  8. Communication of technical building systems. Interfaces, protocols and solutions; Kommunikation technischer Gebaeudesysteme. Schnittstellen, Protokolle und Loesungen

    Energy Technology Data Exchange (ETDEWEB)

    Kranz, H.R. [Siemens AG, Karlsruhe (Germany)

    1995-12-31

    In chapter 18 of the anthology about building control the communication between and with technical building systems is described. After the basics have been explained in the previous chapter interfaces, protocols and solutions are presented in this part. The following aspects are discussed: homogeneous and heterogeneous building automation systems, communication in the field of building automation, demands and characteristic numbers, open communication between heterogeneous systems, announcement and award procedures, protocol selection, FND - firm neutral data transmission system, PROFIBUS, ISP (InterOperable Systems Project) and Fieldbus Foundation with ``profile``; EIB (European Installation Bus), the standard bus for building system technology, BACNet (Building Automation Control Network) and EcheLON, open systems for building automation. (BWI) [Deutsch] Kapitel 18 des Sammelbandes ueber Building Control geht auf das Thema der Kommunikation zwischen und mit technischen Gebaeudesystemen ein. Nachdem im vorherigen Kapitel die Grundlagen besprochen wurden, wird im vorliegenden Teil auf Schnittstellen, Protokolle und Loesungen eingegangen. In diesem Zusammenhang werden folgenden Themenbereiche angesprochen: Homogene und heterogene GA-Systeme; Kommunikation in der Gebaeudeautomation; Anforderungen und Kennwert; offene Kommunikation heterogener Systeme; Ausschreibungs- und Vergabeprozeduren; Protokollauswahl; FND, das firmenneutrale Datenuebertragungsprotokoll; PROFIBUS, ISP und Fieldbus Foundation mit `Profil`; EIB, der Standardbus fuer die Gebaeudesystemtechnik; BACNet und EcheLON; Offene Systeme fuer die Gebaeudeautomation. (BWI)

  9. Theoretical particle physics. Technical progress report, May 1, 1985-April 30, 1986

    International Nuclear Information System (INIS)

    Gottlieb, S.A.; Hendry, A.W.; Kostelecky, V.A.; Lichtenberg, D.B.

    1986-05-01

    Research activities during this past year included theoretical work in lattice gauge theory, EMC effect, supersymmetry and supergravity, weak interactions including CP violation, and superstrings. Progress in all these areas is reported

  10. Symbol manipulation by computer applied to plasma physics. Technical progress report 2

    International Nuclear Information System (INIS)

    Rosen, B.

    1977-09-01

    Progress has been made in automating the calculation of parametric processes analytically by computer. The computations are performed automatically to lowest order quickly and efficiently. Work has started on a method for solving the nonlinear differential equations describing interacting modes

  11. University of Florida, University research program in robotics. Annual technical progress report

    International Nuclear Information System (INIS)

    Crane, C.D. III; Tulenko, J.S.

    1994-05-01

    Progress is reported in the areas of environmental hardening, database, world modeling, vision, man-machine interface, advanced liquid metal reactor inspection robot, and articulated transporter/manipulator system (ATMS) development

  12. Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1, 1997--July 31, 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    Progress summaries are provided from the Amarillo National Center for Plutonium. Programs include the plutonium information resource center, environment, public health, and safety, education and training, nuclear and other material studies.

  13. Research in elementary particle physics. Technical progress report, June 1, 1983-May 31, 1984

    International Nuclear Information System (INIS)

    Kirsch, L.E.; Schnitzer, H.J.; Bensinger, J.R.; Abbott, L.F.

    1984-01-01

    Under this contract, research has been performed on both the theoretical and experimental properties of elementary particles. A brief description of the work which is either in progress or has been completed is given. Publications are listed

  14. Research in elementary particle physics: Technical progress report, June 1, 1987-May 31, 1988

    International Nuclear Information System (INIS)

    Kirsch, L.E.; Schnitzer, H.J.; Abbott, L.F.; Bensinger, J.R.; Blocker, C.A.

    1988-01-01

    The main topics discussed in the progress report: electron/photon algorithm groups; W and Z analysis; heavy quark analysis; gas gain monitoring; database upgrade; CDF test beam studies; string theory; cosmology; and neutral networks

  15. University of Florida, University research program in robotics. Annual technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Crane, C.D. III; Tulenko, J.S.

    1994-05-01

    Progress is reported in the areas of environmental hardening, database, world modeling, vision, man-machine interface, advanced liquid metal reactor inspection robot, and articulated transporter/manipulator system (ATMS) development.

  16. INFLUENCE OF ORGANIZATIONAL AND TECHNOLOGICAL SOLUTIONS TO TECHNICAL AND ECONOMICAL INDICATORS IN PROJECT OF HEAT INSULATION FACADES

    Directory of Open Access Journals (Sweden)

    BABIJ I. N. Cand. Sc. (Tech., Associate Professor,

    2016-09-01

    Full Text Available Summary. Raising of problem. The article dedicated to the solution important problems of choosing rational technical and economic indicators of the duration and cost the process heat insulation facades of buildings by means of experimental and statistical modeling organizational and technological solutions. For this we used the results of numerical experiment, theory a shorthand experiment planning and contemporary computer programs. Purpose. We used experimentally-statistical modeling to establish the impact of organizational and technological solutions for heat insulation of facades by hinged ventilated systems on technical and economic parameters of the project, such as duration and cost. Conclusion. We investigated depending duration assembly jobs and manufacturing cost on the value and combination of variable factors experimental and statistical modeling of construction processes and results patterns of change in studied parameters.

  17. Technical progress report for the quarter 1 October-31 December 1980

    International Nuclear Information System (INIS)

    1981-01-01

    This report describes the technical accomplishments on the commercial nuclear waste management programs and on the geologic disposal of nuclear wastes. The program is organized into eight tasks: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management

  18. Atmospheric Effects of Nuclear Energy Centers (AENEC) Program. Annual technical progress report, July 1975--September 1976

    International Nuclear Information System (INIS)

    Patrinos, A.A.; Hoffman, H.W.

    1977-04-01

    The Technical Memorandum contains information of a preliminary nature from the six participants of the Program describing their activities and presenting the results obtained during the reporting period. The birth of the Program, its definition and evolution are described, and a complete breakdown of responsibilities and tasks assigned to the six AENEC participants is presented

  19. The Michigan high-level radioactive waste program: Final technical progress report

    International Nuclear Information System (INIS)

    1987-01-01

    This report comprises the state of Michigan's final technical report on the location of a proposed high-level radioactive waste disposal site. Included are a list of Michigan's efforts to review the DOE proposal and a detailed report on the application of geographic information systems analysis techniques to the review process

  20. Developing Technical Writing Skills in the Physical Chemistry Laboratory: A Progressive Approach Employing Peer Review

    Science.gov (United States)

    Gragson, Derek E.; Hagen, John P.

    2010-01-01

    Writing formal "journal-style" lab reports is often one of the requirements chemistry and biochemistry students encounter in the physical chemistry laboratory. Helping students improve their technical writing skills is the primary reason this type of writing is a requirement in the physical chemistry laboratory. Developing these skills is an…

  1. Technical progress report for the quarter 1 October-31 December 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    This report describes the technical accomplishments on the commercial nuclear waste management programs and on the geologic disposal of nuclear wastes. The program is organized into eight tasks: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management. (DLC)

  2. GT-MHR COMMERCIALZATION STUDY. TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD MAY 1 THROUGH MAY 31, 2003

    International Nuclear Information System (INIS)

    SHENOY, A.S.

    2003-01-01

    A271 GT-MHR COMMERCIALZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD MAY 1 THROUGH MAY 31, 2003. Petten advised GA the start of the HFR-EU2 irradiation is being delayed until late July 2004. HFR-EU1 (pebble fuel) is also delayed until February/March 2004. The reason for the delays was implementation of new financial regulations at Petten that delayed the contracts for capsule fabrication. Review of the MHR-2 Fuel Product Specification was completed. Revision of the specification to incorporate the review results is in progress. Detailed test matrices have been drafted for capsule irradiation tests and for post-irradiation heating tests proposed for development and qualification of advanced coated-particle fuels capable of meeting anticipated VHTR fuel performance requirements

  3. Overview of progress in European medium sized tokamaks towards an integrated plasma-edge/wall solution

    Science.gov (United States)

    Meyer, H.; Eich, T.; Beurskens, M.; Coda, S.; Hakola, A.; Martin, P.; Adamek, J.; Agostini, M.; Aguiam, D.; Ahn, J.; Aho-Mantila, L.; Akers, R.; Albanese, R.; Aledda, R.; Alessi, E.; Allan, S.; Alves, D.; Ambrosino, R.; Amicucci, L.; Anand, H.; Anastassiou, G.; Andrèbe, Y.; Angioni, C.; Apruzzese, G.; Ariola, M.; Arnichand, H.; Arter, W.; Baciero, A.; Barnes, M.; Barrera, L.; Behn, R.; Bencze, A.; Bernardo, J.; Bernert, M.; Bettini, P.; Bilková, P.; Bin, W.; Birkenmeier, G.; Bizarro, J. P. S.; Blanchard, P.; Blanken, T.; Bluteau, M.; Bobkov, V.; Bogar, O.; Böhm, P.; Bolzonella, T.; Boncagni, L.; Botrugno, A.; Bottereau, C.; Bouquey, F.; Bourdelle, C.; Brémond, S.; Brezinsek, S.; Brida, D.; Brochard, F.; Buchanan, J.; Bufferand, H.; Buratti, P.; Cahyna, P.; Calabrò, G.; Camenen, Y.; Caniello, R.; Cannas, B.; Canton, A.; Cardinali, A.; Carnevale, D.; Carr, M.; Carralero, D.; Carvalho, P.; Casali, L.; Castaldo, C.; Castejón, F.; Castro, R.; Causa, F.; Cavazzana, R.; Cavedon, M.; Cecconello, M.; Ceccuzzi, S.; Cesario, R.; Challis, C. D.; Chapman, I. T.; Chapman, S.; Chernyshova, M.; Choi, D.; Cianfarani, C.; Ciraolo, G.; Citrin, J.; Clairet, F.; Classen, I.; Coelho, R.; Coenen, J. W.; Colas, L.; Conway, G.; Corre, Y.; Costea, S.; Crisanti, F.; Cruz, N.; Cseh, G.; Czarnecka, A.; D'Arcangelo, O.; De Angeli, M.; De Masi, G.; De Temmerman, G.; De Tommasi, G.; Decker, J.; Delogu, R. S.; Dendy, R.; Denner, P.; Di Troia, C.; Dimitrova, M.; D'Inca, R.; Dorić, V.; Douai, D.; Drenik, A.; Dudson, B.; Dunai, D.; Dunne, M.; Duval, B. P.; Easy, L.; Elmore, S.; Erdös, B.; Esposito, B.; Fable, E.; Faitsch, M.; Fanni, A.; Fedorczak, N.; Felici, F.; Ferreira, J.; Février, O.; Ficker, O.; Fietz, S.; Figini, L.; Figueiredo, A.; Fil, A.; Fishpool, G.; Fitzgerald, M.; Fontana, M.; Ford, O.; Frassinetti, L.; Fridström, R.; Frigione, D.; Fuchert, G.; Fuchs, C.; Furno Palumbo, M.; Futatani, S.; Gabellieri, L.; Gałązka, K.; Galdon-Quiroga, J.; Galeani, S.; Gallart, D.; Gallo, A.; Galperti, C.; Gao, Y.; Garavaglia, S.; Garcia, J.; Garcia-Carrasco, A.; Garcia-Lopez, J.; Garcia-Munoz, M.; Gardarein, J.-L.; Garzotti, L.; Gaspar, J.; Gauthier, E.; Geelen, P.; Geiger, B.; Ghendrih, P.; Ghezzi, F.; Giacomelli, L.; Giannone, L.; Giovannozzi, E.; Giroud, C.; Gleason González, C.; Gobbin, M.; Goodman, T. P.; Gorini, G.; Gospodarczyk, M.; Granucci, G.; Gruber, M.; Gude, A.; Guimarais, L.; Guirlet, R.; Gunn, J.; Hacek, P.; Hacquin, S.; Hall, S.; Ham, C.; Happel, T.; Harrison, J.; Harting, D.; Hauer, V.; Havlickova, E.; Hellsten, T.; Helou, W.; Henderson, S.; Hennequin, P.; Heyn, M.; Hnat, B.; Hölzl, M.; Hogeweij, D.; Honoré, C.; Hopf, C.; Horáček, J.; Hornung, G.; Horváth, L.; Huang, Z.; Huber, A.; Igitkhanov, J.; Igochine, V.; Imrisek, M.; Innocente, P.; Ionita-Schrittwieser, C.; Isliker, H.; Ivanova-Stanik, I.; Jacobsen, A. S.; Jacquet, P.; Jakubowski, M.; Jardin, A.; Jaulmes, F.; Jenko, F.; Jensen, T.; Jeppe Miki Busk, O.; Jessen, M.; Joffrin, E.; Jones, O.; Jonsson, T.; Kallenbach, A.; Kallinikos, N.; Kálvin, S.; Kappatou, A.; Karhunen, J.; Karpushov, A.; Kasilov, S.; Kasprowicz, G.; Kendl, A.; Kernbichler, W.; Kim, D.; Kirk, A.; Kjer, S.; Klimek, I.; Kocsis, G.; Kogut, D.; Komm, M.; Korsholm, S. B.; Koslowski, H. R.; Koubiti, M.; Kovacic, J.; Kovarik, K.; Krawczyk, N.; Krbec, J.; Krieger, K.; Krivska, A.; Kube, R.; Kudlacek, O.; Kurki-Suonio, T.; Labit, B.; Laggner, F. M.; Laguardia, L.; Lahtinen, A.; Lalousis, P.; Lang, P.; Lauber, P.; Lazányi, N.; Lazaros, A.; Le, H. B.; Lebschy, A.; Leddy, J.; Lefévre, L.; Lehnen, M.; Leipold, F.; Lessig, A.; Leyland, M.; Li, L.; Liang, Y.; Lipschultz, B.; Liu, Y. Q.; Loarer, T.; Loarte, A.; Loewenhoff, T.; Lomanowski, B.; Loschiavo, V. P.; Lunt, T.; Lupelli, I.; Lux, H.; Lyssoivan, A.; Madsen, J.; Maget, P.; Maggi, C.; Maggiora, R.; Magnussen, M. L.; Mailloux, J.; Maljaars, B.; Malygin, A.; Mantica, P.; Mantsinen, M.; Maraschek, M.; Marchand, B.; Marconato, N.; Marini, C.; Marinucci, M.; Markovic, T.; Marocco, D.; Marrelli, L.; Martin, Y.; Solis, J. R. Martin; Martitsch, A.; Mastrostefano, S.; Mattei, M.; Matthews, G.; Mavridis, M.; Mayoral, M.-L.; Mazon, D.; McCarthy, P.; McAdams, R.; McArdle, G.; McCarthy, P.; McClements, K.; McDermott, R.; McMillan, B.; Meisl, G.; Merle, A.; Meyer, O.; Milanesio, D.; Militello, F.; Miron, I. G.; Mitosinkova, K.; Mlynar, J.; Mlynek, A.; Molina, D.; Molina, P.; Monakhov, I.; Morales, J.; Moreau, D.; Morel, P.; Moret, J.-M.; Moro, A.; Moulton, D.; Müller, H. W.; Nabais, F.; Nardon, E.; Naulin, V.; Nemes-Czopf, A.; Nespoli, F.; Neu, R.; Nielsen, A. H.; Nielsen, S. K.; Nikolaeva, V.; Nimb, S.; Nocente, M.; Nouailletas, R.; Nowak, S.; Oberkofler, M.; Oberparleiter, M.; Ochoukov, R.; Odstrčil, T.; Olsen, J.; Omotani, J.; O'Mullane, M. G.; Orain, F.; Osterman, N.; Paccagnella, R.; Pamela, S.; Pangione, L.; Panjan, M.; Papp, G.; Papřok, R.; Parail, V.; Parra, F. I.; Pau, A.; Pautasso, G.; Pehkonen, S.-P.; Pereira, A.; Perelli Cippo, E.; Pericoli Ridolfini, V.; Peterka, M.; Petersson, P.; Petrzilka, V.; Piovesan, P.; Piron, C.; Pironti, A.; Pisano, F.; Pisokas, T.; Pitts, R.; Ploumistakis, I.; Plyusnin, V.; Pokol, G.; Poljak, D.; Pölöskei, P.; Popovic, Z.; Pór, G.; Porte, L.; Potzel, S.; Predebon, I.; Preynas, M.; Primc, G.; Pucella, G.; Puiatti, M. E.; Pütterich, T.; Rack, M.; Ramogida, G.; Rapson, C.; Rasmussen, J. Juul; Rasmussen, J.; Rattá, G. A.; Ratynskaia, S.; Ravera, G.; Réfy, D.; Reich, M.; Reimerdes, H.; Reimold, F.; Reinke, M.; Reiser, D.; Resnik, M.; Reux, C.; Ripamonti, D.; Rittich, D.; Riva, G.; Rodriguez-Ramos, M.; Rohde, V.; Rosato, J.; Ryter, F.; Saarelma, S.; Sabot, R.; Saint-Laurent, F.; Salewski, M.; Salmi, A.; Samaddar, D.; Sanchis-Sanchez, L.; Santos, J.; Sauter, O.; Scannell, R.; Scheffer, M.; Schneider, M.; Schneider, B.; Schneider, P.; Schneller, M.; Schrittwieser, R.; Schubert, M.; Schweinzer, J.; Seidl, J.; Sertoli, M.; Šesnić, S.; Shabbir, A.; Shalpegin, A.; Shanahan, B.; Sharapov, S.; Sheikh, U.; Sias, G.; Sieglin, B.; Silva, C.; Silva, A.; Silva Fuglister, M.; Simpson, J.; Snicker, A.; Sommariva, C.; Sozzi, C.; Spagnolo, S.; Spizzo, G.; Spolaore, M.; Stange, T.; Stejner Pedersen, M.; Stepanov, I.; Stober, J.; Strand, P.; Šušnjara, A.; Suttrop, W.; Szepesi, T.; Tál, B.; Tala, T.; Tamain, P.; Tardini, G.; Tardocchi, M.; Teplukhina, A.; Terranova, D.; Testa, D.; Theiler, C.; Thornton, A.; Tolias, P.; Tophøj, L.; Treutterer, W.; Trevisan, G. L.; Tripsky, M.; Tsironis, C.; Tsui, C.; Tudisco, O.; Uccello, A.; Urban, J.; Valisa, M.; Vallejos, P.; Valovic, M.; Van den Brand, H.; Vanovac, B.; Varoutis, S.; Vartanian, S.; Vega, J.; Verdoolaege, G.; Verhaegh, K.; Vermare, L.; Vianello, N.; Vicente, J.; Viezzer, E.; Vignitchouk, L.; Vijvers, W. A. J.; Villone, F.; Viola, B.; Vlahos, L.; Voitsekhovitch, I.; Vondráček, P.; Vu, N. M. T.; Wagner, D.; Walkden, N.; Wang, N.; Wauters, T.; Weiland, M.; Weinzettl, V.; Westerhof, E.; Wiesenberger, M.; Willensdorfer, M.; Wischmeier, M.; Wodniak, I.; Wolfrum, E.; Yadykin, D.; Zagórski, R.; Zammuto, I.; Zanca, P.; Zaplotnik, R.; Zestanakis, P.; Zhang, W.; Zoletnik, S.; Zuin, M.; ASDEX Upgrade, the; MAST; TCV Teams

    2017-10-01

    Integrating the plasma core performance with an edge and scrape-off layer (SOL) that leads to tolerable heat and particle loads on the wall is a major challenge. The new European medium size tokamak task force (EU-MST) coordinates research on ASDEX Upgrade (AUG), MAST and TCV. This multi-machine approach within EU-MST, covering a wide parameter range, is instrumental to progress in the field, as ITER and DEMO core/pedestal and SOL parameters are not achievable simultaneously in present day devices. A two prong approach is adopted. On the one hand, scenarios with tolerable transient heat and particle loads, including active edge localised mode (ELM) control are developed. On the other hand, divertor solutions including advanced magnetic configurations are studied. Considerable progress has been made on both approaches, in particular in the fields of: ELM control with resonant magnetic perturbations (RMP), small ELM regimes, detachment onset and control, as well as filamentary scrape-off-layer transport. For example full ELM suppression has now been achieved on AUG at low collisionality with n  =  2 RMP maintaining good confinement {{H}\\text{H≤ft(98,\\text{y}2\\right)}}≈ 0.95 . Advances have been made with respect to detachment onset and control. Studies in advanced divertor configurations (Snowflake, Super-X and X-point target divertor) shed new light on SOL physics. Cross field filamentary transport has been characterised in a wide parameter regime on AUG, MAST and TCV progressing the theoretical and experimental understanding crucial for predicting first wall loads in ITER and DEMO. Conditions in the SOL also play a crucial role for ELM stability and access to small ELM regimes. In the future we will refer to the author list of the paper as the EUROfusion MST1 Team.

  4. Harmonization of clinical laboratories in Africa: a multidisciplinary approach to identify innovative and sustainable technical solutions.

    Science.gov (United States)

    Putoto, Giovanni; Cortese, Antonella; Pecorari, Ilaria; Musi, Roberto; Nunziata, Enrico

    2015-06-01

    In an effective and efficient health system, laboratory medicine should play a critical role. This is not the case in Africa, where there is a lack of demand for diagnostic exams due to mistrust of health laboratory performance. Doctors with Africa CUAMM (Collegio Universitario Aspiranti Medici Missionari) is a non-profit organization, working mainly in sub-Saharan Africa (Angola, Ethiopia, Mozambique, Sierra Leone, South Sudan, Tanzania and Uganda) to help and sustain local health systems. Doctors with Africa CUAMM has advocated the need for a harmonized model for health laboratories to assess and evaluate the performance of the facilities in which they operate. In order to develop a harmonized model for African health laboratories, previous attempts at strengthening them through standardization were taken into consideration and reviewed. A survey with four Italian clinicians experienced in the field was then performed to try and understand the actual needs of health facilities. Finally a market survey was conducted to find new technologies able to update the resulting model. Comparison of actual laboratories with the developed standard - which represents the best setting any African health laboratory could aim for - allowed shortcomings in expected services to be identified and interventions subsequently prioritized. The most appropriate equipment was proposed to perform the envisaged techniques. The suitability of appliances was evaluated in consideration of recognized international recommendations, reported experiences in the field, and the availability of innovative solutions that can be performed on site in rural areas, but require minimal sample preparation and little technical expertise. The present work has developed a new, up-to-date, harmonized model for African health laboratories. The authors suggest lists of procedures to challenge the major African health problems - HIV/AIDS, malaria, tubercolosis (TB) - at each level of pyramidal health system. This

  5. Association Euratom - Risø National Laboratory, Technical University of Denmark - Annual Progress Report 2007

    DEFF Research Database (Denmark)

    Michelsen, Poul; Korsholm, Søren Bang; Juul Rasmussen, Jens

    The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the pla......The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction...... phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007....

  6. Optically pumped polarized 23Na vapor target for use in polarized ion source. Technical progress report

    International Nuclear Information System (INIS)

    Anderson, L.W.

    1984-01-01

    We are currently measuring relaxation times in an optically pumped 23 Na vapor target. Our research is directed toward improvements in the optically pumped Na vapor targets used for the production of polarized H - ions. In this progress report we review the properties of the optically pumped polarized H - ion source and especially the optically pumped Na vapor target employed in this source as well as discussing the progress of our research on relaxation times in an optically pumped Na vapor target. 30 references, 6 figures, 3 tables

  7. Experimental Program Final Technical Progress Report: 15 February 2007 to 30 September 2012

    Energy Technology Data Exchange (ETDEWEB)

    Kinney, Edward R. [University of Colorado, Boulder, CO

    2014-09-12

    This is the final technical report of the grant DE-FG02-04ER41301 to the University of Colorado at Boulder entitled "Intermediate Energy Nuclear Physics" and describes the results of our funded activities during the period 15 February 2007 to 30 September 2012. These activities were primarily carried out at Fermilab, RHIC, and the German lab DESY. Significant advances in these experiments were carried out by members of the Colorado group and are described in detail.

  8. Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2011

    DEFF Research Database (Denmark)

    The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark (until 31-12- 2011: Association Euratom – Risø DTU) covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport...... temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2011....

  9. Microwave plasma source for neutral-beam injection systems. Quarterly technical progress report

    International Nuclear Information System (INIS)

    1981-01-01

    The overall program is described and the technical and programmatic reasons for the decision to pursue both the RFI and ECH sources into the current hydrogen test stage is discussed. We consider the general characteristics of plasma sources in the parameter regime of interest for neutral beam applications. The operatonal characteristics, advantages and potential problems of RFI and ECH sources are discussed. In these latter two sections we rely heavily on experience derived from developing RFI and ECH ion engine sources for NASA

  10. Responsive copolymers for enhanced petroleum recovery. Quarterly technical progress report, September 11, 1994--December 22, 1994

    Energy Technology Data Exchange (ETDEWEB)

    McCormick, C.; Hester, R.

    1994-01-01

    Advanced polymer systems that possess microstructural features that are responsive to temperature, electrolyte concentration, and shear conditions are being synthesized which will be superior to polymers presently used for mobility control in enhanced oil recovery. Improved polymer performance is accomplished by controlling hydrophobic or ampholytic interations between individual polymer chains in solution. The advanced polymers will circumbent major problems inherent in conventional EOR polymers in which molecular weight is usually compromised to allow sufficient solution viscosity and uniform reservoir permeation without plugging the porous media. Accomplishments are reported for the following tasks: quaternary ammonium cyclopolymer synthesis; characterization of molecular structure and solution behavior; {sup 23}Na NMR studies of non-binding to anionic polyelectrolytes and solution rheology.

  11. Technical progress, the concept of individualized cancer treatment and the innovation of computer-assisted radiotherapy planning

    International Nuclear Information System (INIS)

    Merkle, K.; Tanneberger, S.; Matschke, S.

    1985-01-01

    After a first step of cancerogenesis, the further development of the tumor is an individual process. At the end of this process the tumor is formed as an individual in the individual. The individuality of cancer exists on the level of organs, tissues and cells and includes an individual tumor-host relationship. Today, optimized cancer treatment requires a most precise biological characterization possible of the tumor and of the tumor-host relationship, which will provide objective information about the individual character of every tumor. Routine analysis and strict therapeutic consideration of the clinical and biological individuality of human cancer can offer real chances for the improvement of cancer treatment. A routine acquisition of individual tumor characteristics will be possible only if methods and equipment are available for the registration of suitable parameters. In this context technical innovations have an essential influence on the realization of the concept of individualized cancer treatment. With the method of flow cytophotometry and other techniques examples are given in how far the ideas of individual cancer management can be realized by introduction of new technical solutions into medical research and clinical practice. Unfortunately there is still a lack of methodology in individualizing cancer treatment. The individualization of radiotherapy is connected to an extremely high degree of technical innovations. Particularly this refers to the topometrical description of the target volume in relation to the adjacent anatomical structures and the body contour as well as the fitting of isodoses to the shape and size of the target volume. As an example of innovation of a technical solution for individual radiotherapy planning the computer-assisted radiotherapy planning system DOPSY is described. (author)

  12. Optimal design and routing of power lines; ecological, technical and economic perspectives (OPTIPOL). Progress report 2012

    Energy Technology Data Exchange (ETDEWEB)

    Bevanger, Kjetil; Bartzke, Gundula; Broeseth, Henrik; Dahl, Espen Lie; Gjershaug, Jan Ove; Hanssen, Frank; Jacobsen, Karl-Otto; Kleven, Oddmund; Kvaloey, Paal; May, Roel; Meaas, Roger; Nygaaard, Torgeir; Resnaes, Steinar; Stokke, Sigbjoern; Thomassen, Joern

    2012-07-01

    birds in the database, compared to only 117 a year earlier. WP5 - 'A Least Cost Path (LCP) toolbox for optimal route routing of power lines', has developed an LCP-pilot to demonstrate the LCP method, based on the impact studies were undertaken prior to construction of a 420 kV transmission line in Central Norway 2005. Relevant economic, ecological and technological environment criteria based on suggestions from interested users (NGOs, government, industry, etc.), was used. LCP-pilot and a fuzzy-logic approach of this was demonstrated in the first dialogue-based workshop, 23.-24. april 2012. The seminar, which had an emphasis on criteria definitions were followed up with a working seminar that focused criterion values ??on 20 november 2012. Lecture - 'A Least Cost Path (LCP) Toolbox for Optimal Routing of Power Lines, -was presented and submitted as contributions to the conference report from 'The 10th ROW Conference' in Arizona, 'The 32nd Annual Conference of the International Association for Impact Assessment (IAIA12) ' in Porto, Portugal, and 'The ESRI European User Conference' in Oslo. WP6 - 'Birds and camouflaging of power lines', has almost completed the final report, 'Power line camouflaging. An assessment of the ecological and technical challenges'. 'Because of the budget situation in CEDREN However, completion of the report postponed until the end of April 2013. WP7 - 'Effect of line marking / modifications remedial measures against bird mortality' has almost completed the final report 'Opportunities and limitations in terms of reducing mortality in birds due to collision and electrocution.' Due to overall budget situation in CEDREN the report deferred to the end of april 2013. WP8, 'guidelines for technological solutions that may reduce mortality in birds because of the power line's', has focused topics relating to the labeling, design, insulation, camouflage and wiring. The results, which are presented in the notes and articles, will be implemented in

  13. Index to Nuclear Safety: a technical progress review by chrology, permuted title, and author, Volume 11(1) through Volume 20(6)

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W B; Passiakos, M

    1980-06-01

    This index to Nuclear Safety, a bimonthly technical progress review, covers articles published in Nuclear Safety, Volume II, No. 1 (January-February 1970), through Volume 20, No. 6 (November-December 1979). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 600 technical articles published in Nuclear Safety in the last ten years are listed in this index.

  14. Accelerator research studies. Technical progress report, July 1, 1985-June 30, 1986

    International Nuclear Information System (INIS)

    1986-01-01

    Progress is reported in these areas: study of instabilities and emittance growth in periodic focusing systems for intense beams; study of collective ion acceleration by intense electron beams and pulse powered plasma focus; and study of microwave sources and parameter scaling for high-frequency linacs

  15. Experimental studies of elementary particle interactions at high energies: Technical progress report

    International Nuclear Information System (INIS)

    1987-01-01

    This paper discusses progress of experiments at CERN and Fermilab. At CERN, data accumulation and analysis is discussed for the UA-6 experiment, which involves proton-antiproton collisions. At Fermilab, the testing of a collider detector for the Tevatron is discussed

  16. Accelerator research studies: Technical progress report, June 1, 1988--May 31, 1989

    International Nuclear Information System (INIS)

    1989-01-01

    This report discusses research progress in the following general topics: Study of transport and longitudinal compression of intense, high-brightness beams; study of collective ion acceleration by intense electron beams and pulse powered plasma focus; and study of microwave sources and parameter scaling for high-frequency electron-positron supercollider linacs

  17. High beta and second stability region transport and stability analysis: Technical progress report

    International Nuclear Information System (INIS)

    Hughes, M.H.; Phillips, M.W.

    1995-03-01

    This report summarizes MHD equilibrium and stability studies carried out at Northrop Grumman's Advanced Technology and Development Center during the 12 month period starting March 1, 1994. Progress is reported in both ideal and resistive MHD modeling of TFTR plasmas. The development of codes to calculate the significant effects of highly anisotropic pressure distributions is discussed along with results from this model

  18. Chemistry of gaseous lower-valent actinide halides. Technical progress report

    International Nuclear Information System (INIS)

    Hildenbrand, D.L.

    1984-01-01

    Objective is to provide thermochemical data for key actinide halide and oxyhalide systems. Progress is reported on bond dissociation energies of gaseous ThCl 4 , ThCl 3 , ThCl 2 , and ThCl; bond dissociation energies of ruthenium fluorides; and mass spectroscopy of UF 6

  19. Savannah River Ecology Laboratory annual technical progress report of ecological research, period ending July 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Vaitkus, M.R.; Wein, G.R. [eds.; Johnson, G.

    1993-11-01

    This progress report gives an overview of research programs at the Savannah River Site. Topics include; environmental operations support, wood stork foraging and breeding, defense waste processing, environmental stresses, alterations in the environment due to pollutants, wetland ecology, biodiversity, pond drawdown studies, and environmental toxicology.

  20. High beta and second stability region transport and stability analysis. Technical progress report

    International Nuclear Information System (INIS)

    Hughes, M.H.; Phillips, M.W.

    1994-09-01

    This report summarizes MHD equilibrium and stability studies carried out at Grumman's Corporate Research Center during the 6 month period starting March 1, 1994. Progress is reported in both ideal and resistive MHD modeling of TFTR plasmas. The development of codes to calculate the significant effects of highly anisotropic pressure distributions is discussed along with initial results from this model

  1. XML: Solution for the integration of nuclear power plant data and technical documents

    International Nuclear Information System (INIS)

    Gordillo, F.

    2000-01-01

    Assuring proper operation of the systems that make up a nuclear power plant requires handling a massive amount of technical documents. This technical documentation, consisting mainly of system descriptions, operating and maintenance procedures, safety procedures, etc, presents particular characteristics, mainly: Great volume of information. High contents in figures and graphics. High reliability required. Multiple cross-references among documents. (Author)

  2. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 1. Technical Report # 0919

    Science.gov (United States)

    Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grade 1. These measures, available as part of easyCBM [TM], an online progress monitoring assessment system, were developed in 2008 and administered to approximately 2800 students from schools…

  3. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Kindergarten. Technical Report # 0921

    Science.gov (United States)

    Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in kindergarten. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2008 and administered to approximately 2800 students from…

  4. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 3. Technical Report # 09-02

    Science.gov (United States)

    Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  5. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 5. Technical Report # 09-01

    Science.gov (United States)

    Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  6. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 2. Technical Report # 0920

    Science.gov (United States)

    Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  7. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 7. Technical Report 0908

    Science.gov (United States)

    Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  8. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 4. Technical Report # 09-03

    Science.gov (United States)

    Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  9. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 8. Technical Report # 09-04

    Science.gov (United States)

    Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  10. Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2012

    DEFF Research Database (Denmark)

    The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium...... and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities on fusion materials research (Tungsten and ODSFS). Other activities are system analysis...

  11. Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2013

    DEFF Research Database (Denmark)

    The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium...... and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities on fusion materials research (Tungsten and ODSFS). Other activities are system analysis...

  12. [Review of draft Crystalline Repository Project reports]: Technical progress report, CY 1985-1986

    International Nuclear Information System (INIS)

    1986-01-01

    During the period (CY 1985-86) of this report, the Wisconsin Radioactive Waste Review Board provided technical services under the contract with DOE. These included Participation in the development of variables and screening techniques that would be used in identifying those rock bodies in the Area Recommendation Report (ARR); reviewing and commenting on the report and developing a procedure in which local residents could have input into the process; sought resumption of negotiations with DOE on a full Consultation and Cooperation (CandC) agreement; and Participating in workshops and provided comments on two major DOE transportation documents, ''Transportation Business Plan: Strategy Options Document,'' and ''Transportation Institutional Plan.''

  13. New imaging systems in nuclear medicine. Technical progress report, July 1, 1975--March 15, 1976

    International Nuclear Information System (INIS)

    Brownell, G.L.

    1976-01-01

    This progress report covers four areas: development of positron instrumentation, development of NUMEDICS computer system and software, application of cyclotron-produced isotopes ( 11 C, 68 Ga, 13 N, 15 O, and 82 Rb), and application of the NUMEDICS computer system in nuclear medicine. The development of transverse section positron imaging has had a significant impact and a positron camera was designed specifically for transverse section imaging of heart and lungs. The computer net (NUMEDICS II) is progressing rapidly in design and software development. Clinical studies have demonstrated the feasibility of measuring cerebral blood flow using a variety of positron emitting radiopharmaceuticals and oxygen utilization using 15 O 2 . Rubidium-82 also appears to be a promising agent for measurement of cerebral blood flow

  14. Nuclear structure theory. Technical progress report, September 1, 1982-August 31, 1984

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1984-01-01

    Research progress is reported. Spectral Averaging studies are outlined including the theory of level densities for interacting nucleons, the properties of single-particle nuclear excitations, spectral distributions for fixed symmetries, and applications to the secular behavior of fluctuation measures in complex nuclei. Collective States research is described, in particular the boson-fermion symmetries which are related to the U(5) limit of the interacting boson model. Nuclear Reaction studies are described including the statistical theory of pion absorption, direct reactions at intermediate energies, and the properties of the off-shell πN t-matrix. Progress is reported on the quark theory of nuclear matter and the construction of models for a Fermi fluid which, near the nuclear ground state, is a fluid of nucleons composed of quarks, and, at high densities or temperatures, is a quark fluid. Applications of formal scattering theory to the study of phase-conjugate optics are discussed. Publications are listed

  15. AFR spent fuel storage program. Technical progress report, January 1981-March 1981

    International Nuclear Information System (INIS)

    1981-01-01

    Work on this project is focused on developing design and licensing information for the model facility. Deliverables were submitted to DOE for facility modification, security design, and licensing documentation. Work is essentially complete on the high-density rack design with deliverable planned for April 30, 1981. A continuing program for completion of design and licensing information development was initiated by AGNS in February 1981. Progress to date is satisfactory

  16. U.C. Davis high energy particle physics research: Technical progress report -- 1990

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-12-31

    Summaries of progress made for this period is given for each of the following areas: (1) Task A--Experiment, H1 detector at DESY; (2) Task C--Experiment, AMY detector at KEK; (3) Task D--Experiment, fixed target detectors at Fermilab; (4) Task F--Experiment, PEP detector at SLAC and pixel detector; (5) Task B--Theory, particle physics; and (6) Task E--Theory, particle physics.

  17. Nuclear structure theory. Annual technical progress report, October 1, 1979-August 31, 1980

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1980-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: statistical spectroscopy (including random matrix methods, with applications to fluctuations in spectra and in strength distributions, and to problems of ergodicity; group symmetries in spectral-distribution theory; electromagnetic and β transitions); meson scattering and absorption by nuclei (including general scattering theory with absorption, multiple scattering theory and its reactive content, statistical theory of absorption); and meson currents in electromagnetic transitions

  18. Nuclear methods in chemical kinetics. Technical progress report, April 1, 1978--March 31, 1979

    International Nuclear Information System (INIS)

    1979-01-01

    Significant progress was achieved in the following products: (1) gas phase thermal F-to-HF reactions; (II) gas phase thermal 18 F olefinic addition reactions; (III) steady state hot atom kinetic theory; (IV) moderator effects on nuclear recoil 18 F substitution reactions; and (V) new experimental methodology. New work has been initiated upon the development of a realisitic potential form of kinetic collision theory

  19. High energy particle physics at Purdue. Annual technical progress report, March 1982-March 1983

    International Nuclear Information System (INIS)

    Gaidos, J.A.; Koltick, D.S.; Loeffler, F.J.

    1983-01-01

    Progress is reported in these areas: a study of electron-positron annihilation using the High Resolution Spectrometer at SLAC; proton decay; extensive muon showers; gamma ray astronomy; the DUMAND project; theoretical work on fundamental problems in electromagnetic, weak, strong, and gravitational interactions; chi production by hadrons; p-nucleus interactions; development of the Collider Detector at Fermilab; and study of the observed hadrons as the relativistic bound states of baryons and antibaryons

  20. Deep vadose zone remediation: technical and policy challenges, opportunities, and progress in achieving cleanup endpoints

    International Nuclear Information System (INIS)

    Wellman, D.M.; Freshley, M.D.; Truex, M.J.; Lee, M.H.

    2013-01-01

    Current requirements for site remediation and closure are standards-based and are often overly conservative, costly, and in some cases, technically impractical. Use of risk-informed alternate endpoints provides a means to achieve remediation goals that are permitted by regulations and are protective of human health and the environment. Alternate endpoints enable the establishment of a path for cleanup that may include intermediate remedial milestones and transition points and/or regulatory alternatives to standards-based remediation. A framework is presented that is centered around developing and refining conceptual models in conjunction with assessing risks and potential endpoints as part of a system-based assessment that integrates site data with scientific understanding of processes that control the distribution and transport of contaminants in the subsurface and pathways to receptors. This system-based assessment and subsequent implementation of the remediation strategy with appropriate monitoring are targeted at providing a holistic approach to addressing risks to human health and the environment. This holistic approach also enables effective predictive analysis of contaminant behavior to provide defensible criteria and data for making long-term decisions. Developing and implementing an alternate endpoint-based approach for remediation and waste site closure presents a number of challenges and opportunities. Categories of these challenges include scientific and technical, regulatory, institutional, and budget and resource allocation issues. Opportunities exist for developing and implementing systems-based approaches with respect to supportive characterization, monitoring, predictive modeling, and remediation approaches. (authors)

  1. Deep vadose zone remediation: technical and policy challenges, opportunities, and progress in achieving cleanup endpoints

    Energy Technology Data Exchange (ETDEWEB)

    Wellman, D.M.; Freshley, M.D.; Truex, M.J.; Lee, M.H. [Pacific Northwest National Laboratory, Richland, Washington (United States)

    2013-07-01

    Current requirements for site remediation and closure are standards-based and are often overly conservative, costly, and in some cases, technically impractical. Use of risk-informed alternate endpoints provides a means to achieve remediation goals that are permitted by regulations and are protective of human health and the environment. Alternate endpoints enable the establishment of a path for cleanup that may include intermediate remedial milestones and transition points and/or regulatory alternatives to standards-based remediation. A framework is presented that is centered around developing and refining conceptual models in conjunction with assessing risks and potential endpoints as part of a system-based assessment that integrates site data with scientific understanding of processes that control the distribution and transport of contaminants in the subsurface and pathways to receptors. This system-based assessment and subsequent implementation of the remediation strategy with appropriate monitoring are targeted at providing a holistic approach to addressing risks to human health and the environment. This holistic approach also enables effective predictive analysis of contaminant behavior to provide defensible criteria and data for making long-term decisions. Developing and implementing an alternate endpoint-based approach for remediation and waste site closure presents a number of challenges and opportunities. Categories of these challenges include scientific and technical, regulatory, institutional, and budget and resource allocation issues. Opportunities exist for developing and implementing systems-based approaches with respect to supportive characterization, monitoring, predictive modeling, and remediation approaches. (authors)

  2. Enhanced age-strengthening by two-step progressive solution treatment in an Mg–Zn–Al–Re alloy

    International Nuclear Information System (INIS)

    Zhang, Jing; Yuan, Fuqing; Du, Yong

    2013-01-01

    Highlights: • A two-step progressive solution treatment schedule was proposed. • The treatment enhanced dissolution of ternary eutectic phases in Mg–Zn–Al alloy. • Solution temperature could break the limit of the ternary eutectic temperature. • There was no microstructural over-heating defect during the progressive heating. • The τ precipitates have a remarkable dispersion strengthening effect. - Abstract: A two-step progressive solution treatment was designed and performed on an as-extruded Mg–7Zn–3Al–0.7Er alloy. The resultant microstructure and mechanical properties were examined by means of scanning electron microscopy, X-ray diffractometer, differential scanning calorimetry and hardness testing. The results showed that the two-step progressive solution treatment could enhance the dissolution of the ternary eutectic phases in the Mg–Zn–Al system without the formation of microstructure over-heating defects. After homogenization for 50 h at 325 °C, the volume fraction of the undissolved particles in the Mg–7Zn–3Al–0.7Er alloy ingot was ∼4.1%. Two-step progressive solution treatment performed on the as-extruded alloy could further dissolve the particles. Only 1.5% undissolved particles remained after the treatment. The supersaturated degree of both the dissolved solute atoms and vacancies in the α-Mg matrix was expected to be increased, resulting in an enhanced age-strengthening, compared with normal solution and aging treatments. Moreover, the processed alloy exhibited a homogenous and stable fine grain structure. Remarkable dispersion strengthening effect of ternary τ (Mg 32 (Al,Zn) 49 ) precipitates occurred in Mg–Zn–Al alloy was also identified

  3. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2010

    Energy Technology Data Exchange (ETDEWEB)

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M. (eds.)

    2011-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2010. (Author)

  4. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2009

    International Nuclear Information System (INIS)

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M.

    2010-04-01

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2009. (Author)

  5. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2009

    Energy Technology Data Exchange (ETDEWEB)

    Korsholm, S B; Michelsen, P K; Rasmussen, J J; Westergaard, C M [eds.

    2010-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2009. (Author)

  6. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2008

    Energy Technology Data Exchange (ETDEWEB)

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M. (eds.)

    2009-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. New activities in technology related to development of high temperature superconductors have been initiated in 2008. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2008. (Author)

  7. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2008

    International Nuclear Information System (INIS)

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M.

    2009-04-01

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. New activities in technology related to development of high temperature superconductors have been initiated in 2008. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2008. (Author)

  8. Progress report [of] Technical Physics and Prototype Engineering Division, April 1982 - March 1984

    International Nuclear Information System (INIS)

    Ramamurthi, S.S.; Chaudhry, Ramesh

    1985-01-01

    The work done by the Technical Physics and Prototype Engineering Division of the Bhabha Atomic Research Centre (BARC) at Bombay during the period from April 1982 to March 1984 is described in the form of summaries. The main thrust of the work of the Division is towards designing, developing, fabricating and if needed, producing on a large scale various instruments, equipment and components required for the programmes of the BARC and the Department of Atomic Energy. The summaries describing the work are grouped under the headings:(1) vacuum, (2) surface analysis, (3) mass spectrometry, (4) electronics, (5) cryogenics, (6) crystals and detectors, (7) glass technology and devices, and (8) optoelectronics. A list of publications of the staff-members of the Division during the report period is given. (M.G.B.)

  9. Association Euratom - Risoe National Laboratory, Technical Univ. of Denmark. Annual progress report 2007

    International Nuclear Information System (INIS)

    Michelsen, P.K.; Korsholm, S.B.; Rasmussen, J.J.

    2008-04-01

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. The activities in technology on investigations of radiation damage of fusion reactor materials have been phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007. (Author)

  10. Association Euratom - Risoe National Laboratory, Technical Univ. of Denmark. Annual progress report 2007

    Energy Technology Data Exchange (ETDEWEB)

    Michelsen, P.K.; Korsholm, S.B.; Rasmussen, J.J. (eds.)

    2008-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. The activities in technology on investigations of radiation damage of fusion reactor materials have been phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007. (Author)

  11. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2010

    International Nuclear Information System (INIS)

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M.

    2011-04-01

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2010. (Author)

  12. Fusion programs in applied plasma physics. Technical progress report, July 11, 1992--May 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-07-01

    This report summarizes the progress made in theoretical and experimental research funded by US Department of Energy Grant No. DE-FG03-92ER54150, during the period July 11, 1992 through May 31, 1993. Four main tasks are reported: applied plasma physics theory, alpha particle diagnostic, edge and current density diagnostic, and plasma rotation drive. The report also discusses the research plans for the theory and experimental programs for the next grant year. Reports and publications supported by the grant during this period are listed in the final section.

  13. Decontamination Systems Information and Research Program. Quarterly technical progress report, July 1--September 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    Progress reports are presented for the following projects: systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies--drain-enhanced soil flushing (DESF) for organic contaminants removal; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors--monolayer and multilayer self-assembled films for chemical sensors; Winfield Lock and Dam remediation; Winfield cleanup survey; assessment of technologies for hazardous waste site remediation--non-treatment technologies and pilot scale test facility implementation; assessment of environmental remediation storage technology; assessment of environmental remediation excavation technology; assessment of environmental remediation monitoring technology; and remediation of hazardous sites with steam reforming.

  14. Salt repository project: Technical progress report for the quarter 1 April--30 June 1987

    International Nuclear Information System (INIS)

    1987-01-01

    This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of Energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation

  15. Nuclear structure theory. Annual technical progress report, October 1, 1978-September 30, 1979

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1979-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: Statistical spectroscopy, including: Random matrix methods, with applications to fluctuations in spectra and in strength distributions, and to problems of ergodicity; Group symmetries in spectral-distribution theory; Electromagnetic and β transitions. Meson scattering and absorption by nuclei, including: general scattering theory with absorption, multiple scattering theory and its reactive content, statistical theory of absorption, theory of the absorption operator (πNN vertex), theory of πN scattering. A list of publications is included

  16. Combined macroscopic and microscopic approach to the fracture of metals. Technical progress report

    International Nuclear Information System (INIS)

    Asaro, R.J.; Gurland, J.; Needleman, A.; Rice, R.J.

    1979-06-01

    Progress is reported on microscopic fracture mechanisms, including studies of void and crack initiation in steels in the absence and presence of hydrogen, the effects of hydrogen on ductile fracture in medium and high carbon steels; elastic--plastic crack growth including the quasi-stable growth of cracks in ductile solids under increasing load and conditions of instability; and elevated temperature rupture including analysis of the stress field near a crack tip in an elastic-nonlinear viscous material under tensile load as well as the processes of diffusion, and cavitation of grain boundaries in plastically creeping materials

  17. Theoretical nuclear physics. Task B. Technical progress report, August 1, 1982-September 30, 1983

    International Nuclear Information System (INIS)

    1983-01-01

    Progress is reported on the following studies: (a) double delta interactions in pion double charge exchange; (b) isovector correlations in pion-nucleus scattering; (c) nuclear structure effects in pion single charge exchange; (d) a perspective on sequential transfer reactions; (e) inelastic and charge exchange scattering theory; (f) magnitude of the first order DWBA description of the two nuclear transfer reactions; (g) nonlocality effects on deuteron transfer reactions; (h) evaluation of external radial integrals in inelastic electron scattering; (i) experimental observables as a function of Dirac invariant amplitudes; (j) Dirac shell-model wavefunctions in inelastic electron scattering; and (k) impulse approximation Dirac theory of inelastic proton nucleus collective excitations. Publications are listed

  18. High energy particle physics at Purdue. Annual technical progress report, March 1983-March 1984

    International Nuclear Information System (INIS)

    Gaidos, J.A.; Koltick, D.S.; Loeffler, F.J.

    1984-01-01

    Progress is reported in these areas: a study of electron-positron annihilation using the High Resolution Spectrometer; experimental study of proton decay; gamma ray astrophysics; the DUMAND project; fundamental problems in the theory of gravitational, electromagnetic, weak, and strong interactions; chi production by hadrons; study of collective phenomena; search for the onset of collective phenonmena; work on the Collider Detector at Fermilab; search for a deconfined quark-gluon phase of strongly interacting matter at the FNAL proton-antiproton collider; and development of an electrodeless drift chamber

  19. Physics of correlated systems. Technical progress report, December 1996 - June 1999

    International Nuclear Information System (INIS)

    Greene, C.H.

    1999-01-01

    During the current funding period, which covers a period of approximately 2.5 years, the authors have tackled a number of challenging problems that involve nonperturbative particle-particle interactions in two qualitatively different areas: electron-electron interactions in photoionization and photodetachment, and atom-atom interactions in Bose-Einstein condensates. The following discusses the progress achieved in these different areas. The emphasis in this summary will concentrate on approximately the last year of research accomplishments, although the bibliography below includes all research publications that were supported during the time period of this grant

  20. Decontamination Systems Information and Research Program. Quarterly technical progress report, July 1--September 30, 1993

    International Nuclear Information System (INIS)

    1993-10-01

    Progress reports are presented for the following projects: systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies--drain-enhanced soil flushing (DESF) for organic contaminants removal; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors--monolayer and multilayer self-assembled films for chemical sensors; Winfield Lock and Dam remediation; Winfield cleanup survey; assessment of technologies for hazardous waste site remediation--non-treatment technologies and pilot scale test facility implementation; assessment of environmental remediation storage technology; assessment of environmental remediation excavation technology; assessment of environmental remediation monitoring technology; and remediation of hazardous sites with steam reforming

  1. Plasma physics research (Tokapole II). Technical progress report, October 1, 1981-December 31, 1983

    International Nuclear Information System (INIS)

    1983-01-01

    Progress during the 27-month period, October 1, 1981 to December 31, 1983 on Tokapole II research is described. Tokapole II is a 4-node poloidal divertor tokamak that can also be run as an octupole. Research during this period has concentrated on studies of discharges with safety factor q less than one and on the identification of the shear Alfven wave resonance. Other topics include measurements of the loop voltage reduction through ECRH startup, plasma gun refueling, fluctuations and transport, pumped limiter studies, plasma-wall interactions, diagnostic development, polarization of electron cyclotron emission, and poloidal ohmic heating

  2. Nuclear structure theory. Annual technical progress report, October 1, 1977--September 30, 1978

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1978-01-01

    Progress during the past year in the following areas of nuclear structure and reaction theory is summarized: statistical spectroscopy, including random matrix methods, with applications to fluctuations in spectra and in strength distributions, and to problems of erogodicity; group symmetries in spectral distribution theory; effective interactions; statistical reaction theory, applied to ''deep inelastic'' collisions of heavy ions, and to pion absorption by nuclei; meson scattering and absorption by nuclei, including general scattering theory with absorption, multiple scattering theory and its reactive content, models for absorption, theory of the absorption operator (πNN vertex), theory of πN scattering. A list of publications is included

  3. Salt Repository Project technical progress report for the quarter 1 January--31 March 1987

    International Nuclear Information System (INIS)

    1988-03-01

    This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation. 23 refs., 1 fig

  4. Nuclear structure theory. Annual technical progress report, September 1, 1980-August 31, 1981

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1981-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: (1) statistical spectroscopy, including: random matrix methods, with applications to fluctuations in spectra and in strength distributions; group symmetries in spectral-distribution theory; electromagnetic and β transitions, limits to time-reversal symmetry breaking in the nucleon-nucleon interaction; (2) meson scattering and absorption by nuclei, including: general scattering theory with absorption, multiple scattering theory and its reactive content, statistical theory of absorption; and (3) meson currents in electromagnetic transitions

  5. Thermionic cogeneration burner assessment study. Third quarterly technical progress report, April-June, 1983

    Energy Technology Data Exchange (ETDEWEB)

    1983-01-01

    The specific tasks of this study are to mathematically model the thermionic cogeneration burner, experimentally confirm the projected energy flows in a thermal mock-up, make a cost estimate of the burner, including manufacturing, installation and maintenance, review industries in general and determine what groups of industries would be able to use the electrical power generated in the process, select one or more industries out of those for an in-depth study, including determination of the performance required for a thermionic cogeneration system to be competitive in that industry. Progress is reported. (WHK)

  6. Superconducting fault current limiter. Fifth quarterly technical progress report, August 8, 1978-November 7, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1979-01-01

    Progress in the development of fault current limiters for superconducting power transmission systems is reported. The analysis and design of a magnetically switched resistive device and the experimental program were emphasized and reported. A transient heat transfer model was developed which indicates the parameters which are important in determining the thermal heating and recovery of the superconduting film. Designs for the switching coil and the S/C element were also carried out and are reported. A four-pole magnetic coil is recommended; this generates a magnetic field which is nearly perpendicular to spiral or helical S/C film geometrics. A spirally-designed, 3000 ohm limiter is shown to be able to fit within a .5 to 1m inner radius, .05 to .03 m wide, 1.3 to 3.9 m long annualr region. The experimental program has included work on materials development and on prepartion of the switching and thermal recovery experimental facility. The material development program has uncovered several serious short-comings of NbN as the S/C film material. Macroscopic holes and surface debris, and microscopic imperfections reduce the critical current density below the expected value and, in addition, cause nonuniform switching. Reasons for these effects are postulated, and a continuing, vigorous materials program is suggested in hopes of alleviating these problems. Virtually all of the experimental equipment had been installed, and so the magnetic switching and thermal recovery experiments can begin and progress during the next quarter. (LCL)

  7. An accelerator neutron source for BNCT. Technical progress report, 1 June 1993--31 May 1994

    International Nuclear Information System (INIS)

    Blue, T.E.; Vafai, K.

    1994-02-01

    This is the progress report for the project entitled, ''An Accelerator Neutron Source for BNCT.'' The progress report is for the period from July 1, 1993 to date. The overall objective of our research project is to develop an Accelerator Epithermal Neutron Irradiation Facility (AENIF) for Boron Neutron Capture Therapy (BNCT). The AENIF consists of a 2.5 MeV high current proton accelerator, a lithium target to produce source neutrons, and a moderator/reflector assembly to obtain from the energetic source neutrons an epithermal neutron field suitable for BNCT treatments. Our project goals are to develop the non-accelerator components of the AENIF, and to specifically include in our development: (1) design, numerical simulation, and experimental verification of a target assembly which is capable of removing 75 kW of beam power; (2) re-optimization of the moderator assembly design based on in-phantom dose assessments using neutron spectra calculated in phantom and an energy-dependent neutron Relative Biological Effectiveness (RBE); (3) construction of a prototype moderator assembly and confirmation of its design by measurements; (4) design of the shielding of the accelerator and treatment rooms for an AENIF; and (5) design of a high energy beam transport system which is compatible with the shielding design and the thermal-hydraulic design

  8. Technical progress report, Contracts DE-AC02-81ER40014, 40015 and 40016

    International Nuclear Information System (INIS)

    1981-01-01

    This Progress Report summarizes work carried out at the Nuclear Physics Laboratory of the University of Colorado from November 1, 1980 through July 31, 1981, under contracts between the University of Colorado and the United States Department of Energy. The shorter report period of nine months is due to a change to an earlier submission date this year for our proposal for support to begin February 1, 1982. Cyclotron operation, research, and development have been supported under contract DE-AC02-81ER40014. The AVF cyclotron has continued to provide reliable and versatile beams of protons, deuterons, 3 He and 4 He. A wide variety of research results in direct reactions, nuclear structure, and compound reaction mechanisms can be noted in this Progress Report, correlated in many cases to current problems in intermediate energy physics. Theoretical work on nuclear reactions, carried out under contract DE-AC02-81ER40015, has been well matched to our experimental programs in low and intermediate energy physics. One important result has been the recasting of the DWBA in an eikonal expansion suited to high energy reactions. Our efforts in intermediate energy physics, under contract DE-AC02-81ER40016, have emphasized pion scattering studies at LAMPF and TRIUMF and proton induced charge exchange reactions at IUCF. Data for an important test of hadronic charge symmetry have been completed at two energies, using elastic pion-deuteron scattering

  9. The role of technical progress in the process of recalculating oil reserves; Le role du progres technique dans le processus de renouvellement des reserves petrolieres

    Energy Technology Data Exchange (ETDEWEB)

    Boulard, J.N. [Total/Fina/Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France)

    1999-08-01

    Contrary to the concept of resources (which is essentially a geological one), the notion of reserves designates the quantities that are technically and economically recoverable. Beyond the production-related effect, the reserves therefore evolve over time in accordance with numerous technical and economic parameters. Among these parameters, it can be seen that technical progress plays a considerable role throughout the process of converting resources into reserves, including progress in the identification, accessibility and processing of the resources, and improvements in economic viability. After having tackled the problem of measuring the 'technical progress effects' and citing examples, we demonstrate that the evolution in oil reserves is subject to three types of impact. These are a quantitative impact by significantly improving the recovery rates or making it possible to identify hitherto undetectable oil fields, a qualitative impact by widening the resource base thanks to the adoption of new categories of oil (in particular the so-called 'unconventional' oils) and by carrying out the gradual substitution between these resources of differing qualities. There is also a dynamic impact, through the acceleration of resource availability. Through these three approaches, technical progress makes makes it possible to ensure continuity in oil supply and contributes significantly to the recalculation of reserves. It therefore acts as a compensating factor, counterbalancing the progressive depletion of resources. (author)

  10. Advanced development of PV encapsulants. Semiannual technical progress report, June 30, 1995--December 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Holley, W.A. [Springborn Laboratories, Inc., Enfield, CT (United States)

    1996-06-01

    The goals of the NREL PVMaT program are, among others, to reduce module manufacturing costs and improve the quality, and we might add here the reliability, of manufactured PV products. One component critical to the service life of PV modules is the useful life of the EVA resin-based encapsulant which is employed extensively by module manufacturers on a worldwide basis. This pottant has been in commercial use since 1982, and over that time has proven to be a dependable material from the standpoint of production, module fabrication, and end-use. But despite the widespread acceptance of the EVA resin-based A9918 and similar formulations for PV encapsulation, some module producers, end-users, and investigators have reported a yellowing or browning phenomenon with EVA resin-based encapsulants in the field. Wile the incidence of this discoloration/degradation appeared at comparatively few sites at the time that this present program was conceived, it raised serious concern as to the long term reliability of EVA resin-based encapsulation systems. Consequently, under the NREL PVMaT program, Springborn Laboratories proposed a comprehensive study of the EVA aging and discoloration problem and its possible solution(s). During the first year of this program, accelerated U.V. aging methods were surveyed. On careful review of the various types of accelerated U.V. aging equipment available, an Atlas Ci35A Weather-Ometer Xenon Exposure System was selected as appropriate equipment for this work. The following report summarizes how this accelerated aging technique has been used to develop a family of solutions to the discoloration problem, the most significant of which is a series of EVA-based encapsulants which are resistant to discoloration.

  11. GT-MHR COMMERCIALZATION STUDY. TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD JUNE 1 THROUGH JUNE 30, 2003

    International Nuclear Information System (INIS)

    SHENOY, A.S.

    2003-01-01

    A271 GT-MHR COMMERCIALZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD JUNE 1 THROUGH JUNE 30, 2003. Petten was provided with irradiation dimensional change data for both fuel compacts and H-451 graphite for design of the graphite sleeves that hold the fuel compacts to be irradiated in HFR-EU2. The Fuel Sample Product Specification for the Fuel Performance Irradiation Test Capsule MHR-2 was completed and approved. A Work Breakdown Structure was prepared for the development and qualification of advanced coated-particle fuels capable of meeting anticipated fuel performance requirements and work was initiated on preparation of schedules and a cost estimates for the test matrices

  12. GT-MHR COMMERCIALIZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD AUGUST 1 THROUGH AUGUST 31, 2003

    International Nuclear Information System (INIS)

    Shenoy, A.S.

    2003-01-01

    OAK A271 GT-MHR COMERCIALiZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD AUGUST 1 THROUGH AUGUST 31, 2003. In the process of fabricating the MHR-1 irradiation test capsule, Petten has advised that three thermocouples (out of 24) and the Self Powered Neutron detector were damaged during high temperature brazing with the upper capsule lid. Procurement of new TCs and SPN is in process but there will be a delay in the irradiation test of about nine weeks. Startup of the irradiation is now projected to be July or August 2004. In preparation for performing the nuclear design analysis activities required by the advanced fuel studies task, a complete 3-D nuclear design analysis is first being performed of the GT-MHR reference design. This will serve as the baseline for studies of the advanced fuel nuclear design performance

  13. Waste Isolation Safety Assessment Program. Technical progress report for FY-1978

    International Nuclear Information System (INIS)

    Brandstetter, A.; Harwell, M.A.; Howes, B.W.; Benson, G.L.; Bradley, D.J.; Raymond, J.R.; Serne, R.J.; Schilling, A.H.

    1979-07-01

    Associated with commercial nuclear power production in the United States is the generation of potentially hazardous radioactive wastes. The Department of Energy (DOE) is seeking to develop nuclear waste isolation systems in geologic formations that will preclude contact with the biosphere of waste radionuclides in concentrations which are sufficient to cause deleterious impact on humans or their environments. Comprehensive analyses of specific isolation systems are needed to assess the expectations of meeting that objective. The Waste Isolation Safety Assessment Program (WISAP) has been established at the Pacific Northwest Laboratory (operated by Battelle Memorial Institute) for developing the capability of making those analyses. Progress on the following tasks is reported: release scenario analysis, waste form release rate analysis, release consequence analysis, sorption-desorption analysis, and societal acceptance analysis

  14. Repository Technology Program: Technical progress report for the period May 29, 1986--June 30, 1987

    International Nuclear Information System (INIS)

    1988-10-01

    This document reports the progress made in the 13-month period from May 29, 1986--June 30, 1987, on the development of a second geologic repository in rocks other than those being considered for a first repository. Subsequent periods will be covered in reports to be issued on a semiannual basis. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Waste Technology Development (OWTD), a prime contractor of the US. Department of Energy (DOE) Repository Technology Program (RTP) Office in the Repository Technology and Transportation Division (RTTD) of the Office of Geologic Repositories (OGR). The studies include work by other DOE prime contractors and by contractors to the OWTD. 50 refs

  15. Waste Isolation Safety Assessment Program. Technical progress report for FY-1978

    Energy Technology Data Exchange (ETDEWEB)

    Brandstetter, A.; Harwell, M.A.; Howes, B.W.; Benson, G.L.; Bradley, D.J.; Raymond, J.R.; Serne, R.J.; Schilling, A.H.

    1979-07-01

    Associated with commercial nuclear power production in the United States is the generation of potentially hazardous radioactive wastes. The Department of Energy (DOE) is seeking to develop nuclear waste isolation systems in geologic formations that will preclude contact with the biosphere of waste radionuclides in concentrations which are sufficient to cause deleterious impact on humans or their environments. Comprehensive analyses of specific isolation systems are needed to assess the expectations of meeting that objective. The Waste Isolation Safety Assessment Program (WISAP) has been established at the Pacific Northwest Laboratory (operated by Battelle Memorial Institute) for developing the capability of making those analyses. Progress on the following tasks is reported: release scenario analysis, waste form release rate analysis, release consequence analysis, sorption-desorption analysis, and societal acceptance analysis. (DC)

  16. Texas Experimental Tokamak: A plasma research facility. Technical progress report, November 1, 1993--October 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Wootton, A.J.

    1994-07-01

    The purpose is to operate and maintain TEXT Upgrade as a complete facility for applied tokamak physics in order to elucidate the mechanisms of working gas, impurity, and thermal transport in tokamaks and in particular to understand the role of turbulence. So that they can continue to study the physics that is most relevant to the fusion program, TEXT completed a significant device upgrade this year. The new capabilities of the device and new and innovative diagnostics were exploited in all main program areas including: (1) configuration studies; (2) electron cyclotron heating physics; (3) improved confinement modes; (4) edge physics/impurity studies; (5) central turbulence and transport; and (6) transient transport. Details of the progress in each of the research areas are described.

  17. Texas Experimental Tokamak: A plasma research facility. Technical progress report, November 1, 1993--October 31, 1994

    International Nuclear Information System (INIS)

    Wootton, A.J.

    1994-07-01

    The purpose is to operate and maintain TEXT Upgrade as a complete facility for applied tokamak physics in order to elucidate the mechanisms of working gas, impurity, and thermal transport in tokamaks and in particular to understand the role of turbulence. So that they can continue to study the physics that is most relevant to the fusion program, TEXT completed a significant device upgrade this year. The new capabilities of the device and new and innovative diagnostics were exploited in all main program areas including: (1) configuration studies; (2) electron cyclotron heating physics; (3) improved confinement modes; (4) edge physics/impurity studies; (5) central turbulence and transport; and (6) transient transport. Details of the progress in each of the research areas are described

  18. New imaging systems in nuclear medicine. Technical progress report, October 1, 1976--May 31, 1977

    International Nuclear Information System (INIS)

    Brownell, G.L.

    1977-01-01

    Work carried out on the development of instrumentation and techniques for positron scintigraphy is discussed. Progress in positron imaging instrumentation and applications is detailed. The assembly and initial evaluation of the new multicrystal positron camera, PC-II, has been completed. Images have been obtained in both two and three-dimensions which demonstrate the basic physical properties of the instrument. Successful measurements using transverse section imaging have been carried out on animals and human volunteers. Physiological investigation using PC-II is proceeding. A flexible and accurate computer program has been developed for transverse section reconstruction of data acquired by PC-II. This program makes it possible to reconstruct both the activity distribution and the distribution of absorption. The program has been developed in such a way that it can handle variations in the data collection procedure. Clinical studies using PC-I and PC-II are being carried on in areas of heart, lung and brain

  19. [Geothermal system temperature-depth database and model for data analysis]. 5. quarterly technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    Blackwell, D.D.

    1998-04-25

    During this first quarter of the second year of the contract activity has involved several different tasks. The author has continued to work on three tasks most intensively during this quarter: the task of implementing the data base for geothermal system temperature-depth, the maintenance of the WWW site with the heat flow and gradient data base, and finally the development of a modeling capability for analysis of the geothermal system exploration data. The author has completed the task of developing a data base template for geothermal system temperature-depth data that can be used in conjunction with the regional data base that he had already developed and is now implementing it. Progress is described.

  20. Radioecology of natural systems in Colorado. Thirteenth technical progress report, May 1, 1974--April 30, 1975

    International Nuclear Information System (INIS)

    Whicker, F.W.

    1975-01-01

    Progress is reported on studies on the behavior of fallout radionuclides ( 137 Cs and 90 Sr) in selected organisms and natural ecosystems in Colorado. Components of alpine tundra, montane forests, shortgrass plains, and freshwater lakes and streams are currently under investigation. A study on the effect of gut passage on the mean diameter of monodisperse PuO 2 microspheres was initiated. Studies on plutonium in the terrestrial environs of Rocky Flats were initiated in the summer of 1972. Soil movement measurements were conducted to bear on the question of plutonium stability in contaminated areas. The relative importance of root uptake versus aerial deposition was evaluated in the field utilizing a sod block transplant procedure. The study on radiation effects on shortgrass plains vegetation was continued with emphasis on long-term changes in community structure under chronic irradiation stress and recovery patterns. (U.S.)

  1. Research in elementary particle physics. Technical progress report, June 1, 1985-May 31, 1986

    International Nuclear Information System (INIS)

    Kirsch, L.E.; Schnitzer, H.J.; Bensinger, J.R.; Abbott, L.F.; Blocker, C.A.

    1986-01-01

    Progress is reported in both experimental and theoretical elementary particle research. Experimental activities include: construction of the Forward Electromagnetic Shower Counters for the Collider Detector at Fermilab (CDF); a test run in the CDF, involving observation of a small number of proton-antiproton collisions; design of a self-contained single wire proportional chamber with pressure and temperature sensing for monitoring the gain of gases used by various components of the CDF; data acquisition, and calibration. Also included are a search for a dibaryon of strangeness=-1; hyperon weak radiative decay. Theoretical research is reported in the areas of quantum field theory, string theory, elementary particle phenomenology, cosmology, field theory in curved spacetimes, and cosmology. 34 refs

  2. Nuclear structure theory. Annual technical progress report, 1 July 1974--30 June 1975

    International Nuclear Information System (INIS)

    French, J.B.; Koltun, D.S.

    1975-01-01

    Progress during the past year is summarized for the following areas of nuclear structure and reaction theory: Meson interactions with nucleons and nuclei, including inelastic scattering of pions, three-body theories of scattering and absorption of pions by deuterons, and π-p bremsstrahlung. Theory of the effective interaction, including behavior of the expansion in orders of the reaction matrix. Statistical spectroscopy including fluctuations in energy levels and excitation strengths, and sum rules and strength distributions for various excitation processes, including single-nucleon transfer, β decay and multipole giant resonances. Studies of the inverse scattering problem. Studies of nuclear symmetries, of nuclear clustering, and of general nuclear structure by α-transfer reactions, and of nuclear shapes by (d, 3 He) reactions. (U.S.)

  3. Scientific and technical progress in high-energy astrophysics at INPE

    International Nuclear Information System (INIS)

    Bui-Van, N.A.; Jayanthi, U.B.; Jardim, J.O.D.; Braga, J.; Santo, C.M.E.

    1984-01-01

    The recent advances in high-energy Astrophysics pertains to the study of compact objects in galactic nuclei, binary systems and pulsars. These aspects are best understood by the study of the emissions in X- and gamma rays of these objects through the temporal variation in flux and spectrum. The Southern Hemisphere offers some of the unique objects for investigations such as galactic center, the Vela pulsar etc. For high temporal and spectra resolution studies two telescopes 'GeLi' and 'Pulsar' were designed and constructed. To support these scientific activities, a program in balloon launching and data acquisition facilities has been developed since 1971. The 'Balloon Launching Center' of INPE has capacity to launch balloons of -850,000 m 3 with payloads weighting about 1,000 Kg. Taking advantage of these facilities, project 'Bantar', with the goal to measure the atmospheric gamma-ray radiation in the Antartic Region, is under progress. (Author) [pt

  4. Crystalline Repository Project: Technical progress report for the period October 1, 1982--May 28, 1986

    International Nuclear Information System (INIS)

    1988-11-01

    This document reports the progress made on the development of a second geologic repository in crystalline rocks during the duration of the Crystalline Repository Project from its inception in October 1982 to its termination in May 1986. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Waste Technology Development (OWTD), successor to the Office of Crystalline Repository Development. OWTD is a prime contractor of the US Department of Energy (DOE) Repository Technology Program Office, itself the successor to the Crystalline Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Crystalline Repository Development. 151 refs

  5. Savannah River Ecology Laboratory. Annual technical progress report of ecological research

    International Nuclear Information System (INIS)

    Smith, M.H.

    1996-01-01

    The Savannah River Ecology Laboratory (SREL) is a research unit of the University of Georgia (UGA). The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts basic and applied ecological research, as well as education and outreach programs, under a contract with the U.S. Department of Energy (DOE) at the Savannah River Site (SRS) near Aiken, South Carolina. Significant accomplishments were made during the past year in the areas of research, education and service. The Laboratory's research mission was fulfilled with the publication of two books and 143 journal articles and book chapters by faculty, technical and students, and visiting scientists. An additional three books and about 80 journal articles currently are in press. Faculty, technician and students presented 193 lectures, scientific presentations, and posters to colleges and universities, including minority institutions. Dr. J Vaun McArthur organized and conducted the Third Annual SREL Symposium on the Environment: New Concepts in Strewn Ecology: An Integrative Approach. Dr. Michael Newman conducted a 5-day course titled Quantitative Methods in Ecotoxicology, and Dr. Brian Teppen of The Advanced Analytical Center for Environmental Sciences (AACES) taught a 3-day short course titled Introduction to Molecular Modeling of Environmental Systems. Dr. I. Lehr Brisbin co-hosted a meeting of the Crocodile Special Interest Group. Dr. Rebecca Sharitz attended four symposia in Japan during May and June 1996 and conducted meetings of the Executive Committee and Board of the International Association for Ecology (ENTECOL)

  6. Gas-Cooled Thermal Reactor Program. Semiannual technical progress report, October 1, 1982-March 3, 1983

    International Nuclear Information System (INIS)

    1983-06-01

    This report provides descriptions and results of the technical effort during the first half of FY 83 on the Gas-Cooled Thermal Reactor Program. The work on Integration and Management (WBS 01) includes the preparation of the Advanced Systems Concept Evaluation Plan and the Advanced Systems Technology Development Plan in addition to the program management activities. The Market Definition (WBS 03) efforts considered the application of the Modular Reactor System with reforming (MRS-R) to the production of methanol and ammonia and the refining of petroleum. Within the Plant Technology (WBS 13) task there were activities to develop anlytical methods for investigation of Coolant Transport Behavior and to define methods and criteria for High Temperature Structural Engineering design. In addition to the work on the advanced HTGR for process heat users, new activities were initiated in support of the HTGR-SC/C Lead plant Protect (WBS 30 and 31). The Plant Simulation task (WBS 31) was initiated to develop a computer code for simulation of plant operation and for plant transient systems analysis. The efforts on the advanced HTGR systems was performed under the Modular Systems task (WBS 41) to study the potential for multiple small reactors to provide lower costs, improved safety, and higher availability than the large monolithic core reactors

  7. Savannah River Ecology Laboratory. Annual technical progress report of ecological research

    Energy Technology Data Exchange (ETDEWEB)

    Smith, M.H.

    1996-07-31

    The Savannah River Ecology Laboratory (SREL) is a research unit of the University of Georgia (UGA). The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts basic and applied ecological research, as well as education and outreach programs, under a contract with the U.S. Department of Energy (DOE) at the Savannah River Site (SRS) near Aiken, South Carolina. Significant accomplishments were made during the past year in the areas of research, education and service. The Laboratory`s research mission was fulfilled with the publication of two books and 143 journal articles and book chapters by faculty, technical and students, and visiting scientists. An additional three books and about 80 journal articles currently are in press. Faculty, technician and students presented 193 lectures, scientific presentations, and posters to colleges and universities, including minority institutions. Dr. J Vaun McArthur organized and conducted the Third Annual SREL Symposium on the Environment: New Concepts in Strewn Ecology: An Integrative Approach. Dr. Michael Newman conducted a 5-day course titled Quantitative Methods in Ecotoxicology, and Dr. Brian Teppen of The Advanced Analytical Center for Environmental Sciences (AACES) taught a 3-day short course titled Introduction to Molecular Modeling of Environmental Systems. Dr. I. Lehr Brisbin co-hosted a meeting of the Crocodile Special Interest Group. Dr. Rebecca Sharitz attended four symposia in Japan during May and June 1996 and conducted meetings of the Executive Committee and Board of the International Association for Ecology (ENTECOL).

  8. Dual curvature acoustically damped concentrating collector. Semiannual technical progress report, June 1-December 1, 1978

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-12-01

    The project's first objective is to establish, analytically, the cost and performance of design choices within the boundaries of the basic proposed concept. With these cost and performance measures as a guide, the second project objective is to design a cost-effective Dual Curvature collector module and collector field array. The third objective is to establish technical and economic concept feasibility through prototype fabrication and test. The final objective is to define the Dual Curvature collector commercialization requirements. The Dual Curvature collector uses a unique reflector module consisting of a reflective film that is tensioned on a reflector support frame. The tensioned membrane (film) surface approximates a hyperbolic paraboloid that is capable of linear focusing when the surface tracks the sun's apparent motion in one axis. The reflective film can be backed by polystyrene foam with an air space between the film and the foam surfaces. This provides damping of the reflector surface to minimize the effect of wind gusts and physical impacts. The baseline collector is intended to operate at a concentration of ten (10) or greater with a nominal absorber temperature of 150/sup 0/C (300/sup 0/F). The Component Research and Analysis tasks which lead to the selection of a baseline collector configuration are discussed. Also, some preliminary results of the Collector Module Design task are presented.

  9. Pulverized coal firing of aluminum melting furnaces. First annual technical progress report, May 1978-June 1979

    Energy Technology Data Exchange (ETDEWEB)

    West, C.E.; Hines, J.E.; Stewart, D.L. Jr.; Yu, H.

    1979-10-01

    The ultimate objective of this program is the commercial demonstration of an efficient, environmentally acceptable coal firing process suitable for implementation on melting furnaces throughout the aluminum industry. To achieve this goal, the program has been divided into two phases. Phase I has begun with the design and construction of a 350 lb/h (coal) staged slagging cyclone combustor (SSCC) attached to a 7-ft dia aluminum melting ladle furnace. Process development will culminate with a 1000 pph prototype SSCC firing a 40,000 lb capacity open hearth melting furnace at the Alcoa Laboratories. Phase II implementation is currently planned for Alcoa's Lafayette, IN, Works, where two of the ingot plant's five open hearth melting furnaces will be converted to utilize coal. In addition to confirmation of data gathered in Phase I, the effect of extended production schedule operation on equipment and efficiencies will be determined. This work would begin in 1982 pursuant to technical and economic evaluation of the process development at that time. A major design subcontract for assistance in the design of the SSCC is 80% completed.

  10. Technical Progress Report on Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Bill Stanley; Patrick Gonzalez; Sandra Brown; Jenny Henman; Ben Poulter; Sarah Woodhouse Murdock; Neil Sampson; Tim Pearson; Sarah Walker; Zoe Kant; Miguel Calmon; Gilberto Tiepolo

    2006-06-30

    The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st and July 30th 2006. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool. Work is being carried out in Brazil, Belize, Chile, Peru and the USA.

  11. Proposing buffer zones and simple technical solutions for safeguarding river water quality and public health

    Science.gov (United States)

    Podimata, M. V.; Bekri, E. S.; Yannopoulos, P. C.

    2012-04-01

    Alfeios River Basin (ARB) constitutes one of the major hydrologic basins (≈3650km2) of Peloponnisos peninsula in Southern Greece. It is drained by Alfeios River and its tributaries, such as Lousios, Ladhon, Erymanthos, Kladheos, Selinous etc. The present manuscript takes a closer look at the importance of tributary basins and focuses on Erymanthos sub-basin that covers about 360 km2. Erymanthos River springs from Erymanthos Mountain that reaches altitudes of 2200 m and discharges 10 m3/sec, approximately, during the winter period, presenting a sound decrease from half to about an order of magnitude during summertime. Two factors stand out as reasons to select Erymanthos sub-basin as a case study. First, the sub-basin presents a significant variety of ecosystems and comprises a very important river system, since Erymanthos Tributary satisfies, among other uses, drinking water supply for a great majority of citizens in the region. Second, authors' experience of the study area in Research Program Pythagoras II, funded by the European Social Fund (ESF) and the Operational Program for Educational and Vocational Training II (EPEAEK II) of Greece, offers a basis for better understanding of the real problems in the area. Erymanthos watershed, in fact, faces a lot of pressures, in several levels, provoked by human activities and Erymanthos Tributary is vulnerable to pollution. Recognizing the importance of clean water for healthy people, a developing economy, and a sustainable environment, the challenge of the present paper is elaborating human-induced pressures in the study area, analyzing their effects, estimating pollution factors and proposing integrated solutions/tools and a number of methodologies/initiatives used to overcome the problem of contaminating water supply in a catchment that lacks of wastewater treatment and disposal systems. The preservation of a good ecological status in Erymanthos River is not only a necessity for achieving the goals of EU Water

  12. Technical solutions for tritium removal from Cernavoda NPP heavy water systems

    International Nuclear Information System (INIS)

    Barariu, Gheorghe; Panait, Adrian

    2002-01-01

    In CANDU nuclear plants 2400 KCi/GW(e) - year tritium is generated. At a CANDU - 600 reactor similar to Cernavoda NPP Unit 1, 1500 KCi/year of tritium is generated 95% being in the D 2 O moderator, which can achieve a radioactivity level of 80 - 100 Ci/kg. Tritium in heavy water contributes with 30 - 50% to the doses received by operation personnel and with 20% to the radioactivity released to the environment. The extraction of tritium heavy water at CANDU reactors implies the following possibilities: - the radioactivity level reduction in the operation area; - the maintenance and repair cost reduction due to reduction of personnel protection measures and increased labor productivity; - the increase of NPP utilization factor by shutdown time reduction for maintenance and repair; - tritium concentration reduction from technological systems, ensuring thus the possibility of redesigning the systems in order to lower the cost of investment; - profitable use of extracted tritium. Technical measures provided by AECL project for CANDU 600 at Cernavoda make possible to satisfy the current standards concerning tritium concentration in the operation area atmosphere of 5 x 10 -6 Ci/m 3 . The regulations recommend that the radioactivity level should be maintained as low as possible in conformity with ALARA principles. Also, it is possible that norms will become more restrictive in the future, so the tritium removal technology is a good preventive measure which may become very necessary. The methods, which currently reached the industrial or pilot stages, are based on catalyzed chemical exchange, the heavy water electrolysis, and deuterium distillation. They are known as: VPCE - Vapour Phase Catalytic Exchange; LPCE - Liquid Phase Catalytic Exchange; DE - Direct Electrolysis; CD - Cryogenic Distillation. As transfer processes the catalyzed chemical exchange and heavy water electrolysis are used while concentration of tritium gas is done by cryogenic distillation. At present the

  13. Y-12 Development Organization technical progress report: Part 3 -- Metal processing, period ending March 1, 1994

    International Nuclear Information System (INIS)

    Northcutt, W.G. Jr.

    1994-01-01

    As part of the effort to downsize its uranium processing facilities, the Y-12 Plant has supported an investigation to identify extraction solvents that would both work efficiently in centrifugal contactors and be disposed of easily. Various organic ethers, hydroxy ethers, ether ketones, acids, amides, and diketones were studied for their ability to extract uranyl nitrate from aqueous solutions. Although many of these solvents were obtained commercially, others had to be synthesized in-house. The authors found a large range of extraction coefficients for these solvents. Because of steric hindrance or some other factor, certain ethers performed poorly. On the other hand, various mono- and diethers of tetrahydrofurfuryl alcohol exhibited excellent extraction and stripping coefficients for uranyl nitrate, justifying purchase of a pilot plant batch of one of this family of solvents. Likewise, the authors determined the extraction coefficient for one of the two amides synthesized in-house to be quite high

  14. Solid State Sciences Committee (SSSC). Technical progress report, May 1, 1992--April 30, 1993

    International Nuclear Information System (INIS)

    Taylor, R.

    1995-01-01

    The Solid State Sciences Committee (SSSC) of the National Research Council (NRC) is charged with monitoring the health of the field of materials science in the United States. Accordingly, the Committee identifies and examines both broad and specific issues affecting the field. Regular meetings, teleconferences, briefings from agencies and the scientific community, the formation of study panels to prepare reports, and special forums are among the mechanisms used by the SSSC to meet its charge. This progress report presents a review of SSSC activities from May 1, 1992 through April 30, 1993. The details of prior activities are discussed in earlier reports. During the above period, the SSSC has continued to track and participate, when requested, in the development of a Federal initiative on advanced materials and processing. Specifically, the SSSC is presently planning the 1993 SSSC Forum (to be cosponsored with the National Materials Advisory Board (NMAB) and the Washington Materials Forum (WMF)). The thrust will be to highlight the Federal Advanced Materials and Processing Program (AMPP). In keeping with its charge to identify and highlight specific areas for scientific and technological opportunities, the SSSC continued to oversee the conduct of a study on biomolecular materials. Preliminary plans also were developed for a study on neutron science, however, further activity is pending. A proposed study on ultrasmall devices has been expanded and absorbed into a broader context; the BPA, with SSSC participation, is preparing to hold a program initiation meeting to evaluate the need for a study on information technology and hardware

  15. Advanced converter technology. Technical progress report, May 23, 1979-May 22, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Banic, C. V.; Eckhouse, S. A.; Kornbrust, F. J.; Lipman, K.; Peterson, J. L.; Rosati, R. W.

    1980-01-01

    The overall objective of this program is to define an advanced converter system employing 1980's technology in all subsystem and component areas for use in electrochemical energy storage systems. Additional experimental effort will validate elements of the advanced commutation circuitry on a full-scale breadboard basis. Improved models of battery electrical characteristics are beng defined and experimental apparatus is being designed to measure these characteristics and to enable better definition of the battery-power conditioner interface. Improvement of energy-storage system performance through modification of battery converter characteristics will also be investigated. During this first year of the contract, a new more advanced concept for power conditioning based on a concept defined by United Technologies Corporation for fuel cell use was evaluated. This high switching frequency concept has the potential for significantly reducing the size and cost of battery plant power conditioners. As a result, the Department of Energy authorized redirection of the program to first evaluate this new concept and then to reorient the program to adopt this concept as the primary one. Progress is reported. (WHK)

  16. Exploratory research on solvent refined coal liquefaction. Annual technical progress report, January 1-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-09-01

    This report summarizes the progress of the Exploratory Research on Solvent Refined Coal Liquefaction project by The Pittsburg and Midway Coal Mining Co.'s Merriam Laboratory during 1979. In a series of experiments with varying feed gas composition, low levels (5 to 10 mole %) of carbon monoxide had little effect on the SRC II processing of Pittsburgh Seam coal (Powhatan No. 5 Mine) while higher levels (20 to 40 mole %) resulted in a general degradation of operability and reduced oil yields. Addition of finely divided (approx. 1 ..mu..m) pyrite to the reactive Powhatan coal had little effect on oil yields although the molecular weight of the distillation residue was apparently decreased. When finely divided pyrite and magnetite were added to the less reactive coals from the Loveridge and Blacksville No. 1 Mines (also Pittsburgh Seam), however, substantial increases in oil yields and product quality were obtained. In a comparison of upflow and downflow dissolver configurations with Powhatan coal in the SRC II mode, there was no difference in yields or product quality. A study characterizing specific reactors revealed a significantly higher conversion in the SRC I mode with a reactor approximating plug flow conditions compared to a completely backmixed reactor. In the SRC II mode there was only a slightly higher oil yield with the plug flow reactor.

  17. Supramolecular structures for photochemical energy conversion. Technical progress report, 1993--1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    This research project is concerned with the design, synthesis and study by photochemical and spectroscopic methods of complex molecular devices that mimic some important aspects of photosynthetic electron and energy transfer. Properly engineered molecules of this type can functionally mimic photosynthetic light harvesting (singlet-singlet energy transfer between chromophores), photoprotection from light-initiated singlet oxygen damage (triplet-triplet energy transfer from chlorophylls to carotenoid polyenes), and, most importantly, photoinduced multistep electron transfer to generate charge-separated states that preserve some of the photon energy as chemical potential. During the last three years, progress has been made on several fronts, all of which are related to the overall goal. A biomimetic system based on carotenoid-porphyrin-quinone triads has been constructed that demonstrates photoinduced transmembrane charge separation which in turn drives transmembrane proton transfer. Another investigation has focused on the use of proton transfer reactions to stabilize the initial products of photoinduced electron transfer and thereby increase the yield of long-lived charge separation. A third study has investigated the influence of rigid molecular geometries and short donor-acceptor separations on photoinduced electron transfer reactions. Finally, generation and quenching of singlet molecular oxygen by chlorophyll aggregates has been studied. All four studies are described and results are discussed.

  18. Ion rings for magnetic fusion. Technical progress report, August 1, 1993--June 1, 1994

    International Nuclear Information System (INIS)

    Sudan, R.N.

    1994-01-01

    In Our Proposal ''Ion Rings for Magnetic Fusion'' of January 6, 1993, Stage I of our Proposed Program plan (the 12 months) consisted of the following tasks: Experiments on the existing ion ring experimental system IREX to test a new magnetically-controlled anode plasma source (MAP) for the ion beam diode injector; numerical simulations of ion ring formation to optimize design parameters for the field reversed ion ring experiment (FIREX) to be built and operated in Stage II; and designing the power supply for the FIREX injector and the magnetic field system using results for A and B. During the past 7 1/2 months our work has progressed according to the above plan. In addition to testing the MAP diode on IREX we have tested the EMFAPS (evaporating metal film anode plasma source) anode on the Sandia National Laboratories funded LION pulsed power generator. As a result of these experiments, described this paper, we have arrived at the conclusion that EMFAPS anode for the ion at present because the MAP diode beam diode injector is our preferred choice for is still in an early stage of development

  19. University of Colorado at Boulder Nuclear Physics Laboratory technical progress report

    International Nuclear Information System (INIS)

    Peterson, R.J.

    1991-01-01

    This report summarizes experimental work carried out between October 1, 1990, the closing of our Progress Report, and August 14, 1991 at the Nuclear Physics Laboratory of the University of Colorado, Boulder, under contract DE-FG02-ER40269 with the United States Department of Energy. This contract supports broadly based experimental work in intermediate energy nuclear physics. The program includes pion-nucleon studies at TRIUMF and LAMPF, inelastic pion scattering and charge exchange reactions at LAMPF, and nucleon charge exchange at LAMPF/NTOF. The first results of spin-transfer observables in the isovector (rvec p,rvec n) reaction are included in this report. Our data confirm the tentative result from (rvec p,rvec p') reactions that the nuclear isovector spin response shows neither longitudinal enhancement nor transverse queching. Our program in quasifree scattering of high energy pions shows solid evidence of isoscalar enhancement of the nuclear nonspin response. We include several comparisons of the quasifree scattering of different probes. Results from our efforts in the design of accelerator RF cavities are also included in this report

  20. Proton resonance spectroscopy. Quarterly technical progress report, December 1992--November 1995

    International Nuclear Information System (INIS)

    Shriner, J.F. Jr.

    1995-11-01

    Work on chaos in the low-lying levels of nuclei has continued on several fronts. The major effort has been study of the 29 Si(p,γ) reaction with the goal of establishing a complete level scheme for 30 P and analyzing the eigenvalue fluctuations for evidence of chaos. These measurements are in progress, and the current status is described. A related topic is the search for different signatures of chaos which do not require the extremely high degree of completeness and purity necessary for eigenvalue analyses; those efforts are discussed in Sections 2 and 3. The possibility of studying both parity violation and time-reversal invariance violation with charged particle resonances has been explored by performing calculations using experimentally measured resonance parameters. Large enhancements are indeed available; the results are discussed in Sections 4 and 5. Preparations for an experimental study of parity violation using these techniques are ongoing. An undergraduate project searching for experimental evidence of a parity dependence of level density is discussed in Section 6. A number of improvements to the operation of the TUNL KN accelerator have been implemented in the past three years. These are described in Section 7

  1. Proton resonance spectroscopy. Quarterly technical progress report, December 1992--November 1995

    Energy Technology Data Exchange (ETDEWEB)

    Shriner, J.F. Jr.

    1995-11-01

    Work on chaos in the low-lying levels of nuclei has continued on several fronts. The major effort has been study of the {sup 29}Si(p,{gamma}) reaction with the goal of establishing a complete level scheme for {sup 30}P and analyzing the eigenvalue fluctuations for evidence of chaos. These measurements are in progress, and the current status is described. A related topic is the search for different signatures of chaos which do not require the extremely high degree of completeness and purity necessary for eigenvalue analyses; those efforts are discussed in Sections 2 and 3. The possibility of studying both parity violation and time-reversal invariance violation with charged particle resonances has been explored by performing calculations using experimentally measured resonance parameters. Large enhancements are indeed available; the results are discussed in Sections 4 and 5. Preparations for an experimental study of parity violation using these techniques are ongoing. An undergraduate project searching for experimental evidence of a parity dependence of level density is discussed in Section 6. A number of improvements to the operation of the TUNL KN accelerator have been implemented in the past three years. These are described in Section 7.

  2. Technical progress report for UTSI/CFFF MHD program completion and related activity

    International Nuclear Information System (INIS)

    Chapman, James N.; Muehlhauser, Joel W.

    1998-01-01

    Routine preventive maintenance of the DOE Coal Fired Flow Facility (CFFF) is being performed. Modernization programs, funded under subcontract from Foster Wheeler Development Corporation by the DOE HIPPS Program, have been completed on the coal processing system, the data acquisition and control system and the control room. Late in the quarter, all work was stopped on maintenance of the CFFF at DOE instruction. Environmental restoration actions continued with monitoring of groundwater wells and holding pond effluent. Progress is reported on the approved groundwater remediation plan. Actions are underway to dispose of spent seed/ash mixtures and excess coal remaining from the MHD POC program. The status of five (5) High Temperature Superconductor (HTS) projects is reported. A summary is included of the results attained with sol-gel experiments with buffer layers and YBCO. The status of the cost/performance study of electron beam and PLD deposition is pre-sented. A summary of work performed in diagnostics for real time control of HTS processes is presented

  3. TECHNICAL PROGRESS REPORT FOR UTSI/CFFF MHD PROGRAM COMPLETION AND RELATED ACTIVITIES

    Energy Technology Data Exchange (ETDEWEB)

    DR. JAMES N. CHAPMAN; DR. JOEL W. MUEHLHAUSER

    1998-10-23

    Routine preventive maintenance of the DOE Coal Fired Flow Facility (CFFF) is being performed. Modernization programs, funded under subcontract from Foster Wheeler Development Corporation by the DOE HIPPS Program, have been completed on the coal processing system, the data acquisition and control system and the control room. Late in the quarter, all work was stopped on maintenance of the CFFF at DOE instruction. Environmental restoration actions continued with monitoring of groundwater wells and holding pond effluent. Progress is reported on the approved groundwater remediation plan. Actions are underway to dispose of spent seed/ash mixtures and excess coal remaining from the MHD POC program. The status of five (5) High Temperature Superconductor (HTS) projects is reported. A summary is included of the results attained with sol-gel experiments with buffer layers and YBCO. The status of the cost/performance study of electron beam and PLD deposition is pre-sented. A summary of work performed in diagnostics for real time control of HTS processes is presented.

  4. Technical progress report to the Department of Energy on the Solid State Sciences Committee (SSSC)

    International Nuclear Information System (INIS)

    1995-01-01

    The Solid State Sciences Committee (SSSC) of the National Research Council (NRC) is charged with monitoring the health of the field of materials science in the United States. Accordingly, the Committee identifies and examines both broad and specific issues affecting the field. Regular meetings, teleconferences, briefings from agencies and the scientific community, the formation of study panels to prepare reports, and special forums are among the mechanisms used by the SSSC to meet its charge. This progress report presents a review of SSSC activities from May 1, 1992 through April 30, 1993. The details of prior activities are discussed in earlier reports. During the above period, the SSSC has continued to track and participate, when requested, in the development of a Federal initiative on advanced materials and processing. Specifically, the SSSC is presently planning the 1993 SSSC Forum (to be cosponsored with the National Materials Advisory Board (NMAB) and the Washington Materials Forum (WNM)). The thrust will be to highlight the Federal Advanced Materials and Processing Program (AMPP). In keeping with its charge to identify and highlight specific areas for scientific and technological opportunities, the SSSC continued to oversee the conduct of a study on biomolecular materials. Preliminary plans also have been developed for studies on neutron scattering science, on ultrasmall devices, and on molecular routes to materials

  5. Developing a transnational electricity infrastructure offshore: interdependence between technical and regulatory solutions

    NARCIS (Netherlands)

    Hendriks, R.L.; Gibescu, M.; Roggenkamp, M.M.; Kling, W.L.

    2010-01-01

    This paper aims at identifying the options for designing an offshore electricity grid and the legal instruments to create such a grid. It will make a first attempt at presenting the technical and legal considerations which coastal states, EU and national legislators and policy makers should take

  6. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol. 11, No. 1--Vol. 17, No. 6

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W.B.; Klein, A.

    1977-02-23

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970), through Vol. 17, No. 6 (Nov.-Dec. 1976). The index includes a chronological list of articles (including abstract) followed by KWIC and Author Indexes. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 350 technical articles in the last six years of publication.

  7. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol. 11, No. 1--Vol. 17, No. 6

    International Nuclear Information System (INIS)

    Cottrell, W.B.; Klein, A.

    1977-01-01

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970), through Vol. 17, No. 6 (Nov.-Dec. 1976). The index includes a chronological list of articles (including abstract) followed by KWIC and Author Indexes. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 350 technical articles in the last six years of publication

  8. Solvent refined coal (SRC) process. Quarterly technical progress report, January 1980-March 1980. [In process streams

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    This report summarizes the progress of the Solvent Refined Coal (SRC) project at the SRC Pilot Plant in Fort Lewis, Wahsington, and the Process Development Unit (P-99) in Harmarville, Pennsylvania. After the remaining runs of the slurry preheater survey test program were completed January 14, the Fort Lewis Pilot Plant was shut down to inspect Slurry Preheater B and to insulate the coil for future testing at higher rates of heat flux. Radiographic inspection of the coil showed that the welds at the pressure taps and the immersion thermowells did not meet design specifications. Slurry Preheater A was used during the first 12 days of February while weld repairs and modifications to Slurry Preheater B were completed. Two attempts to complete a material balance run on Powhatan No. 6 Mine coal were attempted but neither was successful. Slurry Preheater B was in service the remainder of the quarter. The start of a series of runs at higher heat flux was delayed because of plugging in both the slurry and the hydrogen flow metering systems. Three baseline runs and three slurry runs of the high heat flux program were completed before the plant was shut down March 12 for repair of the Inert Gas Unit. Attempts to complete a fourth slurry run at high heat flux were unsuccessful because of problems with the coal feed handling and the vortex mix systems. Process Development Unit (P-99) completed three of the four runs designed to study the effect of dissolver L/D ratio. The fourth was under way at the end of the period. SRC yield correlations have been developed that include coal properties as independent variables. A preliminary ranking of coals according to their reactivity in PDU P-99 has been made. Techniques for studying coking phenomenona are now in place.

  9. LMFBR flexible pipe joint development program. Annual technical progress report, government fiscal year 1977

    International Nuclear Information System (INIS)

    1978-01-01

    Currently, the ASME Boiler and Pressure Vessel Code does not allow the use of flexible pipe joints (bellows) in Section III, Class 1 reactor primary piping systems. Studies have shown that the primary piping loops of LMFBR's could be simplified by using these joints. This simplification translates directly into shorter primary piping runs and reduced costs for the primary piping system. Further cost savings result through reduced vault sizes and reduced containment building diameter. In addition, the use of flexible joints localizes the motions from thermally-induced piping growth into components which are specifically designed to accommodate this motion. This reduces the stress levels in the piping system and its components. It is thus economically and structurally important that flexible piping joints be available to the LMFBR designer. The overall objective of the Flexible Joint Program is to provide this availability. This will be accomplished through the development of ASME rules which allow the appropriate use of such joints in Section III, Class 1 piping systems and through the development and demonstration of construction methods which satisfy these rules. The rule development includes analytic and testing methodology formulations which will be supported by subscale bellows testing. The construction development and demonstration encompass the design, fabrication, and in-sodium testing of prototypical LMFBR plant-size flexible pipe joints which meet all ASME rule requirements. The satisfactory completion of these developmental goals will result in an approved flexible pipe joint design for the LMFBR. Progress is summarized in the following efforts undertaken during 1977 to accomplish these goals: (1) code case support, (2) engineering and design, (3) material development, (4) testing, and (5) manufacturing development

  10. Advanced thermally stable jet fuels: Technical progress report, October 1994--December 1994

    Energy Technology Data Exchange (ETDEWEB)

    Schobert, H.H.; Eser, S.; Song, C.; Hatcher, P.G.; Boehman, A.; Coleman, M.M.

    1995-02-01

    There are five tasks within this project on thermally stable coal-based jet fuels. Progress on each of the tasks is described. Task 1, Investigation of the quantitative degradation chemistry of fuels, has 5 subtasks which are described: Literature review on thermal stability of jet fuels; Pyrolytic and catalytic reactions of potential endothermic fuels: cis- and trans-decalin; Use of site specific {sup 13}C-labeling to examine the thermal stressing of 1-phenylhexane: A case study for the determination of reaction kinetics in complex fuel mixtures versus model compound studies; Estimation of critical temperatures of jet fuels; and Surface effects on deposit formation in a flow reactor system. Under Task 2, Investigation of incipient deposition, the subtask reported is Uncertainty analysis on growth and deposition of particles during heating of coal-derived aviation gas turbine fuels; under Task 3, Characterization of solid gums, sediments, and carbonaceous deposits, is subtask, Studies of surface chemistry of PX-21 activated carbon during thermal degradation of jet A-1 fuel and n-dodecane; under Task 4, Coal-based fuel stabilization studies, is subtask, Exploratory screening and development potential of jet fuel thermal stabilizers over 400 C; and under Task 5, Exploratory studies on the direct conversion of coal to high quality jet fuels, are 4 subtasks: Novel approaches to low-severity coal liquefaction and coal/resid co-processing using water and dispersed catalysts; Shape-selective naphthalene hydrogenation for production of thermally stable jet fuels; Design of a batch mode and a continuous mode three-phase reactor system for the liquefaction of coal and upgrading of coal liquids; and Exploratory studies on coal liquids upgrading using mesopores molecular sieve catalysts. 136 refs., 69 figs., 24 tabs.

  11. Directional backlight liquid crystal autostereoscopic display: technical challenges, research progress, and prospect (Conference Presentation)

    Science.gov (United States)

    Fan, Hang; Li, Kunyang; Zhou, Yangui; Liang, Haowen; Wang, Jiahui; Zhou, Jianying

    2016-09-01

    Recent upsurge on virtual and augmented realities (VR and AR) has re-ignited the interest to the immerse display technology. The VR/AR technology based on stereoscopic display is believed in its early stage as glasses-free, or autostereoscopic display, will be ultimately adopted for the viewing convenience, visual comfort and for the multi-viewer purposes. On the other hand, autostereoscopic display has not yet received positive market response for the past years neither with stereoscopic displays using shutter or polarized glasses. We shall present the analysis on the real-world applications, rigid user demand, the drawbacks to the existing barrier- and lenticular lens-based LCD autostereoscopy. We shall emphasize the emerging autostereoscopic display, and notably on directional backlight LCD technology using a hybrid spatial- and temporal-control scenario. We report the numerical simulation of a display system using Monte-Carlo ray-tracing method with the human retina as the real image receiver. The system performance is optimized using newly developed figure of merit for system design. The reduced crosstalk in an autostereoscopic system, the enhanced display quality, including the high resolution received by the retina, the display homogeneity without Moiré- and defect-pattern, will be highlighted. Recent research progress including a novel scheme for diffraction-free backlight illumination, the expanded viewing zone for autostereoscopic display, and the novel Fresnel lens array to achieve a near perfect display in 2D/3D mode will be introduced. The experimental demonstration will be presented to the autostereoscopic display with the highest resolution, low crosstalk, Moiré- and defect- pattern free.

  12. Theory of high-energy-collision processes. Technical progress report, January 1-December 31, 1981

    International Nuclear Information System (INIS)

    1982-01-01

    Progress is described in the following areas: (1) several years ago, surprisingly simple expressions were obtained for the differential cross sections of e + e - → μ + μ - γ and e + e - → e + e - γ at high energies. Such simple expressions were generalized to twelve other similar radiative processes in QED and QCD. Afterwards, it was found that these results can be derived easily with the help of helicity amplitudes. This method is being investigated for many other radiative processes; (2) in the two-dimensional Ising model, the horizontal and vertical interaction energies are usually taken to be different. When this idea of different interactions in different directions is applied to the Z 2 lattice gauge theory in four dimensions, a limiting case is found which is exactly solvable. Contrary to numerical calculations at the symmetry point, the phase transition is found to be of second order; (3) on the subject of supersymmetry, general helicity and spin sum rules were obtained for massless and massive supermultiplets, and a functional integral approach was found as a natural setting for Witten's criterion for the occurrence of dynamic symmetry breaking of supersymmetry. A systematic and exhaustive analysis of explicit soft breaking of global supersymmetry has also been carried out using the methods of superfields; (4) the renormalization of the massless Thirring model in the neighborhood of g = -π/2 was studied. The results are consistent with those found previously by placing the model on a lattice; and (5) in studying the effect of laboratory temperature on scattering processes, it was found that transport phenomena play an important role. As a preparation for this study, an exactly solvable case of the nonlinear Boltzmann equation has been found and studied

  13. Nuclear Physics Laboratory, University of Colorado technical progress report, 1976 and proposal for continuation of contract

    International Nuclear Information System (INIS)

    1976-01-01

    This report summarizes the work carried out at the Nuclear Physics Laboratory of the University of Colorado during the period November 1, 1975 to November 1, 1976. The low energy nuclear physics section is dominated by light-ion reaction studies which span a wide range. These include both two-neutron and two-proton transfer reactions, charge exchange and inelastic scattering, as well as single nucleon transfer reactions. The nuclei studied vary widely in their mass and characteristics. These reaction studies have been aided by the multi-use scattering chamber which now allows the energy-loss-spectrometer beam preparation system (beam swinger) to shift from charged particle studies to neutron time-of-flight studies with a minimum loss of time. The intermediate energy section reflects the increase in activity accompanying the arrival of LAMPF data and the initiation of (p,d) studies at the Indiana separated-sector cyclotron. The nucleon removal results provided by the π beam at EPICS previous to completion of the spectrometer have shown that nuclear effects dominate this process, so that the widely used free interaction picture is inadequate. The section entitled ''Other Activities'' reveals continuing activities in new applications of nuclear techniques to problems in medicine and biology. Reactions important to astrophysics continue to be investigated and our trace-element program remains at a high level of activity. The theoretical section reports new progress in understanding magnitudes of two-step reactions by inclusion of finite-range effects. A new finite-range program which is fast and economical has been completed. Intermediate energy results include calculations of π-γ angular correlations, low energy π-nucleus interactions, as well as (p,d) and nucleon scattering calculations for intermediate energies

  14. Improved methods for water shutoff. Final technical progress report, October 1, 1997--September 30, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Seright, R.S.; Liang, J.T.; Schrader, R.; Hagstrom, J. II; Liu, J.; Wavrik, K.

    1998-10-01

    In the United States, more than 20 billion barrels of salt water are produced each year during oilfield operations. A tremendous economic incentive exists to reduce water production if that can be accomplished without significantly sacrificing hydrocarbon production. This three-year research project had three objectives. The first objective was to identify chemical blocking agents that will (a) during placement, flow readily through fractures without penetrating significantly into porous rock and with screening out or developing excessive pressure gradients and (b) at a predictable and controllable time, become immobile and resistant breakdown upon exposure to moderate to high pressure gradients. The second objective was to identify schemes that optimize placement of the above blocking agents. The third objective was to explain why gels and other chemical blocking agents reduce permeability to one phase (e.g., water) more than that to another phase (e.g., oil or gas). The authors also wanted to identify conditions that maximize this phenomenon. This project consisted of three tasks, each of which addressed one of the above objectives. This report describes work performed during the third and final period of the project. During this three-year project, they: (1) Developed a procedure and software for sizing gelant treatments in hydraulically fractured production wells; (2) Developed a method (based on interwell tracer results) to determine the potential for applying gel treatments in naturally fractured reservoirs; (3) Characterized gel properties during extrusion through fractures; (4) Developed a method to predict gel placement in naturally fractured reservoirs; (5) Made progress in elucidating the mechanism for why some gels can reduce permeability to water more than that to oil; (6) Demonstrated the limitations of using water/oil ratio diagnostic plots to distinguish between channeling and coning; and (7) Proposed a philosophy for diagnosing and attacking water

  15. GPHS-RTGs in support of the Cassini RTG Program. Semi annual technical progress report, September 26, 1994--April 2, 1995

    International Nuclear Information System (INIS)

    1995-01-01

    The technical progress achieved during the period 26 September 1994 through 2 April 1995 on Contract DE-AC03-91SF18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described herein. Monthly technical activity for the period 27 February 1995 through 2 April 1995 is included in this progress report. The report addresses tasks, including: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; ETG Fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair; and CAGO acquisition (capital funds)

  16. Progress in improving provincial plans for nutrition through targeted technical assistance and local advocacy in Vietnam.

    Science.gov (United States)

    Harris, Jody; Nguyen, Phuong H; To, Quyen; Frongillo, Edward A; Menon, Purnima

    2016-12-01

    Vietnam has been decentralizing nutrition planning to provinces, which could help with local relevance and accountability. Assessment in 2009 found a continuing top-down approach, limited human capacity, and difficulty in integrating multiple sectors. Alive and Thrive (A&T) provided targeted assistance and capacity-building for 15 provincial plans for nutrition (PPNs). We aimed to (i) assess PPN content and quality improvements 2009-2014, and (ii) explain processes through which change occurred. Data consisted of interview-based assessments of provincial planning processes, annual PPN assessments, and tracking of A&T involvement. At endline, some provinces produced higher quality plans. Local planning skills improved, but capacity remained insufficient. Awareness of and support for nutrition improved, but some policy and legal environments were contradictory. Objectives were clearer, but use of data for planning remained inconsistent. Provinces became more proactive and creative, but remained constrained by slow approval processes and insufficient funding. Targeted assistance and local advocacy can improve decentralized planning, with success dependent on policy and programming contexts and ability to overcome constraints around capacity, investment, data use and remnants of centralized planning. We recommend strong engagement with planners at the national level to understand how to unblock major constraints; solutions must take into consideration the particular political, financial and administrative context. © The Author 2016. Published by Oxford University Press in association with The London School of Hygiene and Tropical Medicine.

  17. Nondestructive Examination (NDE) Detection and Characterization of Degradation Precursors, Technical Progress Report for FY 2012

    Energy Technology Data Exchange (ETDEWEB)

    Ramuhalli, P.; Meyer, R.M.; Fricke, J.M.; Prowant, M.S.; Coble, J.B.; Griffin, J.W.; Pitman, S.G.; Dahl, M.E.; Kafentzis, T.A.; Roosendaal, T.J.

    2012-09-01

    The overall objective of this project was to investigate the effectiveness of nondestructive examination (NDE) technology in detecting material degradation precursors by initiating and growing cracks in selected materials and using NDE methods to measure crack precursors prior to the onset of cracking. Nuclear reactor components are subject to stresses over time that are not precisely known and that make the life expectancy of components difficult to determine. To prevent future issues with the operation of these plants because of unforeseen failure of components, NDE technology is needed that can be used to identify and quantify precursors to macroscopic degradation of materials. Some of the NDE methods being researched as possible solutions to the precursor detection problem are magnetic Barkhausen noise, nonlinear ultrasonics, acoustic emission, eddy current measurements, and guided wave technology. In FY12, the objective was to complete preliminary assessment of advanced NDE techniques for sensitivity to degradation precursors, using prototypical degradation mechanisms in laboratory-scale measurements. This present document reports on the deliverable that meets the following milestone: M3LW-12OR0402143 – Report detailing an initial demonstration on samples from the crack-initiation tests will be provided (demonstrating acceleration of the work).

  18. Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility; FINAL

    International Nuclear Information System (INIS)

    Thomas B. Kirchner

    2002-01-01

    The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

  19. Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility

    International Nuclear Information System (INIS)

    Kirchner, Thomas B.

    2002-01-01

    The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

  20. Savannah River Ecology Laboratory Annual Technical Progress Report of Ecological Research, June 30, 2001

    Energy Technology Data Exchange (ETDEWEB)

    Bertsch, Paul M.; Janecek, Laura; Rosier, Brenda

    2001-06-30

    The Savannah River Ecology Laboratory (SREL) is a research unit of the University of Georgia (UGA) and has been conducting ecological research on the Savannah River Site (SRS) in South Carolina for 50 years. The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts fundamental and applied ecological research, as well as education and outreach programs, under a Cooperative Agreement with the U.S. Department of Energy (DOE) SRS near Aiken, South Carolina. The Laboratory's research mission during the 2001 fiscal year was fulfilled with the publication of one book and 83 journal articles and book chapters by faculty, technical staff, students, and visiting scientists. An additional 77 journal articles have been submitted or are in press. Other noteworthy events took place as faculty members and graduate students received awards. These are described in the section Special Accomplishments of Faculty, Staff, Students, and Administration on page 54. Notable scientific accomplishments include work conducted on contaminant transport, global reptile decline, phytoremediation, and radioecology. Dr. Domy Adriano authored the second edition of his book ''Trace Elements in Terrestrial Environments: Biogeochemistry, Bioavailability, and Risks of Metals'', which was recently published by Springer-Verlag. The book provides a comprehensive treatment of many important aspects of trace elements in the environment. The first edition of the book, published in 1986, has become a widely acclaimed and cited reference. International attention was focused on the problem of reptile species decline with the publication of an article on this topic in the journal ''Bioscience'' in August, 2000. The article's authors included Dr. Whit Gibbons and a number of other SREL herpetologists who researched the growing worldwide problem of decline of reptile species. Factors related

  1. Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility

    Energy Technology Data Exchange (ETDEWEB)

    Thomas B. Kirchner

    2002-03-22

    The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

  2. Technical and economic feasibility of development innovative technological solutions for expansion the adjustment range of high-power CCP

    Science.gov (United States)

    Arakelyan, E. K.; Andryushin, A. V.; Burtsev, S. Y.; Andryushin, K. A.

    2017-11-01

    The analysis of technical and parametric constraints on the adjustment range of highpower CCP and recommended technological solutions in the technical literature for their elimination. Established that in the conditions of toughening the requirements for economy, reliability and maneuverability on the part of the system operator with the participation of CCP in control the frequency and power in the power system, existing methods do not ensure the fulfillment of these requirements. The current situation in the energy sector — the lack of highly manoeuvrable power equipment leads to the need participate in control of power consumption diagrams for all types of power plants, including CCP, although initially they were intended primarily for basic loads. Large-scale research conducted at the department of Automated control systems of technological processes, showed the possibility of a significant expansion of the adjustment range of CCP when it operating in the condensing mode and in the heating mode. The report presents the main results of these research for example the CCP-450 and CCP-450T. Various technological solutions are considered: when CCP in the condensation mode — the use of bypass steam distribution schemes, the transfer of a part of the steam turbine into a low-steam mode; when CCP operation in the heating mode — bypass steam distribution and the transfer CCP to gas turbine unit — power heating plants mode with the transfer the steam turbine to the motor mode. Data on the evaluation of the technical and economic feasibility of the proposed innovative technological solutions are presented in comparison with the methods used to solve this problem, which are used in practice, such as passing through the failures of the electric load graphs by transferring the CCP to the mode of operation with incomplete equipment. When comparing, both the economics, and the maneuverability and reliability of the equipment are considered.

  3. Governing through time: management of radioactive waste in France, organizational changes and the construction of irreversible technical solutions (1950-2014)

    International Nuclear Information System (INIS)

    Blanck, Julie

    2017-01-01

    In France, the problem of radioactive waste has been subjected to different solutions. In 1979, the storage of radioactive waste was entrusted to a specialized operator, the National Agency for Radioactive Waste Management (Andra). Yet, through the course of its history, the Agency has faced many difficulties to implement its projects, which often came under strong public criticism. Still today, while its project of geological disposal is about to move into its industrial phase, the Andra is still widely criticized and serves as a crystallization point for power relationships in the nuclear sector. In order to retrace the evolution of French radioactive waste management since the 1950's, the archival and ethnographic study of the Andra's organizational work provides an insider perspective on how its agents have defined problems, as well as conceived and implemented solutions. Indeed, through this strategic and political work, they have frequently transformed the Agency to fit the progress of its projects. From an industrial subsidiary of the French Atomic Energy Commission (CEA), the Agency was transformed into a finalized research agency, then again into an industrial operator in order to undertake to construction the geological disposal site. Through to these changes, actors have been able to revived criticized projects, without necessarily modifying their contents. In fact, it is not stability but organizational and institutional flexibility, which can account for the preservation of these controversial solutions. Lastly, the problem of radioactive waste crystallizes a multiplicity of temporal logics. The analysis of this work of temporalization, which can be seen as a particular kind of organization, questions the articulation between change and permanency of public action. As such, this study sheds light on the relation between dynamics of problem definition, the construction of irreversible technical solutions, and organizational and temporal work

  4. I-NERI QUARTERLY TECHNICAL PROGRESS REPORT - JANUARY 1 - MARCH 31, 2005

    International Nuclear Information System (INIS)

    Chang Oh

    2005-01-01

    codes. The three categories of experiments were performed in the facility; (1) upper pool cooling trip test, (2) LOFC experiment, (3) emissivity measurement experiment. (C) Prof. NO continued Task 3. (Prof NO) The experimental work of air ingress is going on without any concern: Geometry and size effect test has been completed. The conversion factor for internal surface area was obtained through this experiment. Burn-off test was performed and the uniformity of internal reaction was confirmed. (D) INEEL engineers continued to extend the diffusion model for multiple chemical species and made some calculations. (E) Prof. Lee and Martin at University of Michigan continued to analyze the effect of the stochastic fuel on the neutronic analysis and have initiated fuel depletion calculations for the VHTGR core. Progress during the past quarter includes: Further analysis of stochastic fuel geometry; Preliminary Monte Carlo depletion of full-core VHTGR; and Installation of MCNP5 on Unix cluster

  5. Features of formation spirituality pictures of the world in youth in in the era of information-highlytechnological scientific and technical progress

    Directory of Open Access Journals (Sweden)

    N. V. Polishchuk

    2016-06-01

    Full Text Available In clause necessity of formation of a spiritual picture of the world, anthropocosmos at young generation at the present stage of development much crisis world and, including, the Ukrainian society is proved. In the article the necessity of formation of anthropocosmos-spiritual picture of the world at young generation at the present stage of development bagalicious the world and, in particular, of the Ukrainian society. The proposed definition of new terms: anthropocosmos is a spiritual picture of the world, anthropocosmic spirituality, anthropocosmic worldview and other anthropocentric concepts and definitions in contemporary philosophical and pedagogical discourse. The presented model of the formation of anthropocosmos-spiritual worldview of the young generation in the information and high-tech scientific and technical progress and the author’s interpretation of its philosophical, educational, pedagogical and spiritual essence. It is proved, that having generated in consciousness of the young man a anthropocosmos-spiritual picture of the world, will allow it in conditions of inevitable crash in the near future of a human civilization, if it will not solve present global-civilizational crises and will not avoid geocosmic accidents, to understand sense space-ekzoplanete lives which will be esclusivi, and, therefore, crisis-free, conflict-free, comprehensive and meaningful, anthropocosmos-highly spiritual (divine M. Berdyaev, and, therefore, progressive and virtually eternal as the life of society, which is composed of such anthropocosmos educated individuals. Solved zagalnoosvitnioi sense anthropocosmos spiritual world picture, which is to solve the problem of the choice of life strategies of mankind, the search for new ways of civilization development, in particular, resettlement anthropocosmos-conscious part of humanity for exoplanets space with the aim of preserving the gene pool of humanity and creation of human cosmically

  6. Major Oil Plays in Utah and Vicinity. Quarterly Technical Progress Report

    International Nuclear Information System (INIS)

    Thomas C. Chidsey; Craig D. Morgan; Kevin McClure; Douglas A. Sprinkel; Roger L. Bon; Hellmut H. Doelling

    2003-01-01

    overlying argillaceous and non-fractured units. The best outcrop analogs for Twin Creek reservoirs are found at Devils Slide and near the town of Peoa, Utah, where fractures in dense, homogeneous non-porous limestone beds are in contact with the basal siltstone units (containing sealed fractures) of the overlying units. The shallow marine, Mississippian Leadville Limestone is a major oil and gas reservoir in the Paradox Basin of Utah and Colorado. Hydrocarbons are produced from basement-involved, northwest-trending structural traps with closure on both anticlines and faults. Excellent outcrops of Leadville-equivalent rocks are found along the south flank of the Uinta Mountains, Utah. For example, like the Leadville, the Mississippian Madison Limestone contains zones of solution breccia, fractures, and facies variations. When combined with subsurface geological and production data, these outcrop analogs can improve (1) development drilling and production strategies such as horizontal drilling, (2) reservoir-simulation models, (3) reserve calculations, and (4) design and implementation of secondary/tertiary oil recovery programs and other best practices used in the oil fields of Utah and vicinity. In the southern Green River Formation play of the Uinta Basin, optimal drilling, development, and production practices consist of: (1) owning drilling rigs and frac holding tanks; (2) perforating sandstone beds with more than 8 percent neutron porosity and stimulate with separate fracture treatments; (3) placing completed wells on primary production using artificial lift; (4) converting wells relatively soon to secondary waterflooding maintaining reservoir pressure above the bubble point to maximize oil recovery; (5) developing waterflood units using an alternating injector--producer pattern on 40-acre (16-ha) spacing; and (6) recompleting producing wells by perforating all beds that are productive in the waterflood unit. As part of technology transfer activities during this quarter

  7. Photovoltaic energy in Mali. Technical and organisational challenges of solar solutions deployment

    International Nuclear Information System (INIS)

    Lacroix, Olivier; Lesaffre, Dominique

    2011-01-01

    In 2008, electricity access rate in rural Mali was below 11%. In view of the challenges of electrification and development of rural areas in Mali, solar energy is seen as a strategic technology. The SIDI has asked ENEA to work on the technical and organisational terms ensuring sustainable access and spreading of photovoltaic systems in rural Mali. As such, in this report, ENEA improves the knowledge of the sector's private actors, suggests support architectures tackling the problematic, and highlights critical points by market segments

  8. AFCT/TFCT/ISFS Program. Technical progress report for the period October 1, 1977--December 31, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Hill, O.F. (comp.)

    1978-02-01

    This is the eighth in a series of quarterly progress reports on studies performed for the Alternate Fuel Cycle Technologies/Thorium Fuel Cycle Technologies/International Spent Fuel Receipt and Storage (AFCT/TFCT/ISFS) Program, formerly the LWR Fuel Recycle Program. This program is designed to provide information needed by industry to close the back end of the power reactor fuel cycle. During the past quarter, studies were conducted in the following tasks: Survey of Current Technology of Fuel Handling Techniques; Investigation of Air Cleaning Processes for Removing Tributyl Phosphate (TBP) from Off-Gas Streams; Study of Iodine Chemistry in Process Solutions; Electropolishing to Decontaminate Metallic Waste from Alternate and Thorium Converter Fuel Cycles; and U.S. Scale Transport, Dispersion and Removal Mode Comparison Safety Criticality Experiments. (11 figs., 7 tables)

  9. AFCT/TFCT/ISFS Program. Technical progress report for the period April 1, 1978--June 30, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Hill, O.F. (comp.)

    1978-08-01

    This is the tenth in a series of quarterly progress reports on studies performed for the Alternate Fuel Cycle Technologies/Thorium Fuel Cycle Technologies/International Spent Fuel Receipt and Storage (AFCT/TFCT/ISFS) Program. This program provides information needed by industry to close the back end of the power reactor fuel cycle. During the past quarter, studies were conducted in the following tasks: thorium resource price analyses; spent fuel receipt and storage; investigation of air cleaning processes for removing TBP from off-gas streams; study of iodine chemistry in process solutions, high-level waste treatment; electropolishing to decontaminate metallic waste from alternate and thorium converter fuel cycles; U.S. scale transport, dispersion and removal model comparison; safety criticality experiments; and criticality research in support of thorium fuel cycle.

  10. MC21/CTF and VERA multiphysics solutions to VERA core physics benchmark progression problems 6 and 7

    Directory of Open Access Journals (Sweden)

    Daniel J. Kelly, III

    2017-09-01

    Full Text Available The continuous energy Monte Carlo neutron transport code, MC21, was coupled to the CTF subchannel thermal-hydraulics code using a combination of Consortium for Advanced Simulation of Light Water Reactors (CASL tools and in-house Python scripts. An MC21/CTF solution for VERA Core Physics Benchmark Progression Problem 6 demonstrated good agreement with MC21/COBRA-IE and VERA solutions. The MC21/CTF solution for VERA Core Physics Benchmark Progression Problem 7, Watts Bar Unit 1 at beginning of cycle hot full power equilibrium xenon conditions, is the first published coupled Monte Carlo neutronics/subchannel T-H solution for this problem. MC21/CTF predicted a critical boron concentration of 854.5 ppm, yielding a critical eigenvalue of 0.99994 ± 6.8E-6 (95% confidence interval. Excellent agreement with a VERA solution of Problem 7 was also demonstrated for integral and local power and temperature parameters.

  11. A vision based aerial rbot solution for the IARC 2014 by the Technical University of Madrid

    OpenAIRE

    Pestana Puerta, Jesús; Sánchez López, José Luis; Suárez Fernández, Ramón; Collumeau, Jean-Françoise; Campoy Cervera, Pascual; Martín Cristóbal, Jorge; Molina, Martin; Lope Asiaín, Javier de; Maravall Gomez-Allende, Darío

    2014-01-01

    The IARC competitions aim at making the state of the art in UAV progress. The 2014 challenge deals mainly with GPS/Laser denied navigation, Robot-Robot interaction and Obstacle avoidance in the setting of a ground robot herding problem. We present in this paper a drone which will take part in this competition. The platform and hardware it is composed of and the software we designed are introduced. This software has three main components: the visual information acquisition, the mapping algorit...

  12. Technical solution for data collection, data safety and data privacy legislation: experiences from the SWEET study.

    Science.gov (United States)

    Forsander, Gun; Pellinat, Martin; Volk, Michael; Muller, Markus; Pinelli, Leonardo; Magnen, Agnes; Danne, Thomas; Aschemeier, Bärbel; de Beaufort, Carine

    2012-09-01

    One of the most important tasks of the SWEET study is benchmarking the data collected. Information on the occurrence of the disease of diabetes, the treatment, and their outcomes in children from the different member states of European Union (EU) is crucial. How the collection of data is realized is essential, concerning both the technical issues and the results. The creation of SWEET Centers of Reference (CoR), all over Europe will be facilitated by the access to safe data collection, where legal aspects and privacy are ascertained. To describe the rationale for- and the technical procedure in the data collection implementation, in the SWEET study. Selected data on all patients treated at SWEET CoR are collected. The SWEET project data collection and management system, consists of modular components for data collection, online data interchange, and a database for statistical analysis. The SWEET study and the organization of CoR aims for the goal of offering an updated, secure, and continuous evaluation of diabetes treatment regimens for all children with diabetes in Europe. To support this goal, an appropriate and secure data management system as described in this paper has been created. © 2012 John Wiley & Sons A/S.

  13. Technical issues and solutions on ITER first wall beryllium application. Industrial viewpoint

    International Nuclear Information System (INIS)

    Iwadachi, T.; Uda, M.; Ito, M.; Miyakawa, M.; Ibuki, M.

    2004-01-01

    Beryllium is selected as reference armor material of ITER primary first wall and is joined to the copper alloy heat sink such as CuCrZr or Dispersion Strengthened Copper (DSCu) Various joining technologies have been successfully developed and the manufacturing possibilities of large size first wall panels with beryllium armor has been demonstrated. Based on such results, further technical improvement is needed to reduce manufacturing cost and ensure the reliability of joining in actual size first wall. The technical issues to optimize the fabrication process of beryllium attachment were shown in this paper from an industrial point of view. Determination of the optimum size and the surface qualities of beryllium tiles are important issues in term of the material specification to ensure joining reliability and to reduce cost. The consolidation method and the finish machining methods of beryllium tiles are also critical in terms of material cost. These items should be determined by paying concern to the accommodation of the joining methods. The selections of slitting methods for attached beryllium have a great influence on fabrication cost. In the actual fabrication of beryllium attachment, safety provisions for exposure to beryllium in working environment and the recycling of the waste from the fabrication processes will be concerned sufficiently. (author)

  14. Feasibility analysis of AP1000 wireless communication system and selection of technical solutions

    International Nuclear Information System (INIS)

    Zhao Xin

    2012-01-01

    This article expatiates the rationality and feasibility of AP1000 nuclear power plant adopts wireless communication system as the first choice in routine and emergency operations, compares and analysed. 5 major wireless communication technology solutions, and introduces the Wi-Fi based wireless communication system architecture. (author)

  15. Dismantling of civilian nuclear powered fleet technical support vessels. engineering solutions - 59386

    International Nuclear Information System (INIS)

    Kulikov, Konstantin N.; Nizamutdinov, Rinat A.; Abramov, Andrey N.

    2012-01-01

    At the present time six nuclear technical support vessels are operated and maintained by Atomflot. Two of them (Volodarsky FTB (floating technical base) and Lepse FTB) were taken out of service for decommissioning and are stored afloat. One more vessel Lotta FTB should be decommissioned during next two years. The nuclear technological support ships carrying spent nuclear fuel (SNF), liquid and solid radioactive wastes (LRW and SRW) appear to be a possible radiation contamination of Murmansk region and Kola Bay because the Ship long-term storage afloat has the negative effect on hull's structures technical condition. As a result of this in the context of the Federal Program 'Nuclear and Radiation Safety' (2008-2015) NIPTB Onega OAO was engaged by state corporation Rosatom to develop the dismantling procedure for Volodarsky FTB and Lotta FTB. Before developing of nuclear technological support ships decommissioning projects the technical and economic assessment of decommissioning/dismantling was carried out. The following options were examined: - formation of module as one-piece Ship's hull for long-term storage at Saida Bay; - formation of separated modules for long-term storage at Saida Bay; - complete dismantling of hull's structures, systems and equipment with packing all generated SRW into certified long-term storage containers. This paper contains description of options, research procedure, comparative analysis of options of decommissioning and dismantling (D and D) of nuclear technological support ships and its difference with dismantling of nuclear submarine. On the basis of the technical and economic assessment of FTB D and D options the least expensive on the first D and D stage and the least duration option is the option 1 (Formation of module as one-piece Ship's hull for long-term storage at Saida Bay). By the implementation of the given option there will be the need of large areas for modules storage at Saida Bay. It was not considered while working out

  16. Feed-in tariffs versus quotas: how to promote renewable s and stimulate technical progress for cost decrease?

    International Nuclear Information System (INIS)

    Menanteau, Ph.; Finon, D.; Lamy, M.L.

    2002-01-01

    Incentive schemes for the development of renewable energy sources may focus on quantities (defining national targets and setting up bidding systems, or quota systems providing for green certificate trading), or they may focus on prices (feed-in tariffs). Whatever the system chosen, the role of the public authorities is quite specific: to stimulate technical progress and speed up the technological learning processes so that ultimately renewable energy technologies will be able to compete with conventional technologies, once the environmental costs have been internalized. A comparison of instruments must thus take into account the characteristics of the innovation process and adoption conditions (uncertainties regarding cost curves, learning effects) which means also looking at dynamic efficiency criteria. The paper concludes that a system of feed-in tariffs is more efficient than a bidding system, but highlights the theoretical interest of green certificate trading which must be confirmed through practice, given the influence of market structures and rules on the performance of this type of approach. (author)

  17. Modeling the impacts of climate change and technical progress on the wheat yield in inland China: An autoregressive distributed lag approach.

    Science.gov (United States)

    Zhai, Shiyan; Song, Genxin; Qin, Yaochen; Ye, Xinyue; Lee, Jay

    2017-01-01

    This study aims to evaluate the impacts of climate change and technical progress on the wheat yield per unit area from 1970 to 2014 in Henan, the largest agricultural province in China, using an autoregressive distributed lag approach. The bounded F-test for cointegration among the model variables yielded evidence of a long-run relationship among climate change, technical progress, and the wheat yield per unit area. In the long run, agricultural machinery and fertilizer use both had significantly positive impacts on the per unit area wheat yield. A 1% increase in the aggregate quantity of fertilizer use increased the wheat yield by 0.19%. Additionally, a 1% increase in machine use increased the wheat yield by 0.21%. In contrast, precipitation during the wheat growth period (from emergence to maturity, consisting of the period from last October to June) led to a decrease in the wheat yield per unit area. In the short run, the coefficient of the aggregate quantity of fertilizer used was negative. Land size had a significantly positive impact on the per unit area wheat yield in the short run. There was no significant short-run or long-run impact of temperature on the wheat yield per unit area in Henan Province. The results of our analysis suggest that climate change had a weak impact on the wheat yield, while technical progress played an important role in increasing the wheat yield per unit area. The results of this study have implications for national and local agriculture policies under climate change. To design well-targeted agriculture adaptation policies for the future and to reduce the adverse effects of climate change on the wheat yield, climate change and technical progress factors should be considered simultaneously. In addition, adaptive measures associated with technical progress should be given more attention.

  18. Modeling the impacts of climate change and technical progress on the wheat yield in inland China: An autoregressive distributed lag approach.

    Directory of Open Access Journals (Sweden)

    Shiyan Zhai

    Full Text Available This study aims to evaluate the impacts of climate change and technical progress on the wheat yield per unit area from 1970 to 2014 in Henan, the largest agricultural province in China, using an autoregressive distributed lag approach. The bounded F-test for cointegration among the model variables yielded evidence of a long-run relationship among climate change, technical progress, and the wheat yield per unit area. In the long run, agricultural machinery and fertilizer use both had significantly positive impacts on the per unit area wheat yield. A 1% increase in the aggregate quantity of fertilizer use increased the wheat yield by 0.19%. Additionally, a 1% increase in machine use increased the wheat yield by 0.21%. In contrast, precipitation during the wheat growth period (from emergence to maturity, consisting of the period from last October to June led to a decrease in the wheat yield per unit area. In the short run, the coefficient of the aggregate quantity of fertilizer used was negative. Land size had a significantly positive impact on the per unit area wheat yield in the short run. There was no significant short-run or long-run impact of temperature on the wheat yield per unit area in Henan Province. The results of our analysis suggest that climate change had a weak impact on the wheat yield, while technical progress played an important role in increasing the wheat yield per unit area. The results of this study have implications for national and local agriculture policies under climate change. To design well-targeted agriculture adaptation policies for the future and to reduce the adverse effects of climate change on the wheat yield, climate change and technical progress factors should be considered simultaneously. In addition, adaptive measures associated with technical progress should be given more attention.

  19. Laboratory evaluation of limestone and lime neutralization of acidic uranium mill tailings solution. Progress report

    International Nuclear Information System (INIS)

    Opitz, B.E.; Dodson, M.E.; Serne, R.J.

    1984-02-01

    Experiments were conducted to evaluate a two-step neutralization scheme for treatment of acidic uranium mill tailings solutions. Tailings solutions from the Lucky Mc Mill and Exxon Highland Mill, both in Wyoming, were neutralized with limestone, CaCO 3 , to an intermediate pH of 4.0 or 5.0, followed by lime, Ca(OH) 2 , neutralization to pH 7.3. The combination limestone/lime treatment methods, CaCO 3 neutralization to pH 4 followed by neutralization with Ca(OH) 2 to pH 7.3 resulted in the highest quality effluent solution with respect to EPA's water quality guidelines. The combination method is the most cost-effective treatment procedure tested in our studies. Neutralization experiments to evaluate the optimum solution pH for contaminant removal were performed on the same two tailings solutions using only lime Ca(OH) 2 as the neutralizing agent. The data indicate solution neutralization above pH 7.3 does not significantly increase removal of pH dependent contaminants from solution. Column leaching experiments were performed on the neutralized sludge material (the precipitated solid material which forms as the acidic tailings solutions are neutralized to pH 4 or above). The sludges were contacted with laboratory prepared synthetic ground water until several effluent pore volumes were collected. Effluent solutions were analyzed for macro ions, trace metals and radionuclides in an effort to evaluate the long term effectiveness of attenuating contaminants in sludges formed during solution neutralization. Neutralized sludge leaching experiments indicate that Ca, Na, Mg, Se, Cl, and SO 4 are the only constituents which show solution concentrations significantly higher than the synthetic ground water in the early pore volumes of long-term leaching studies

  20. Alkali-Activated Mortars for Sustainable Building Solutions: Effect of Binder Composition on Technical Performance

    Directory of Open Access Journals (Sweden)

    Agnese Attanasio

    2018-02-01

    Full Text Available There is a growing interest in the construction sector in the use of sustainable binders as an alternative to ordinary Portland cement, the production of which is highly impacting on the environment, due to high carbon dioxide emissions and energy consumption. Alkali-activated binders, especially those resulting from low-cost industrial by-products, such as coal fly ash or metallurgical slag, represent a sustainable option for cement replacement, though their use is more challenging, due to some technological issues related to workability or curing conditions. This paper presents sustainable alkali-activated mortars cured in room conditions and based on metakaolin, fly ash, and furnace slag (both by-products resulting from local sources and relevant blends, aiming at their real scale application in the building sector. The effect of binder composition—gradually adjusted taking into consideration technical and environmental aspects (use of industrial by-products in place of natural materials in the view of resources saving—on the performance (workability, compressive strength of different mortar formulations, is discussed in detail. Some guidelines for the design of cement-free binders are given, taking into consideration the effect of each investigated alumino-silicate component. The technical feasibility to produce the mortars with standard procedures and equipment, the curing in room conditions, the promising results achieved in terms of workability and mechanical performance (from 20.0 MPa up to 52.0 MPa, confirm the potential of such materials for practical applications (masonry mortars of class M20 and Md. The cement-free binders resulting from this study can be used as reference for the development of mortars and concrete formulations for sustainable building materials production.

  1. Technical progress report

    International Nuclear Information System (INIS)

    1982-01-01

    This report summarizes the work carried out by personnel at the Nuclear Physics Laboratory of the University of Colorado from about August 1, 1981 to October 1, 1982, under contract with the Department of Energy. The intermediate energy studies summarized in this report were carried out at the meson physics facilities at Los Alamos (LAMPF), the cyclotron at Indiana University (IUCF), and the meson physics facilities at Vancouver (TRIUMF). This year, for the first time, intermediate energy experimental studies are being reported in separate documents from the low energy and theoretical nuclear physics efforts. Experimental studies are reported on pion-nucleus interactions, charge exchange reactions, nucleon transfer reactions, and apparatus development

  2. 1996 technical progress report

    International Nuclear Information System (INIS)

    1997-01-01

    Summaries of the researches are grouped into programs as follows: research and development in food and agriculture; research and development in health, environment and industry which includes all the PNRI research projects in 1996; scientific and technological services; and the nuclear regulations, licensing and safeguards of the institute

  3. 1997 technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-07-01

    This report presents the on-going research and development projects of the Philippine Nuclear Research Institute (PNRI) in the fields of agriculture, environment and industry, scientific and technological services and nuclear regulations, licensing and safeguards.

  4. Annual technical progress report

    International Nuclear Information System (INIS)

    1980-01-01

    During the present contract period Phaedrus has begun operation as a true tandem mirror. This was accomplished by achieving the rf sustained mode in which the plug densities were built up by a combination of central cell gas puffing and plug ICRH following stream gun turn off. It was demonstrated that the tandem mirror plasma could be sustained by plug ICRH for up to 1 msec following decay of the external plasma. In this mode plasma characteristics were no longer dominated by problems associated with a high conductivity stream gun plasma in the external region (as was the case in many previous experiments in Phaedrus). Among these problems were (1) line tying which significantly reduced instabilities in a way that would not apply to reactors and (2) low electron temperatures which had been held to approx. 20 eV

  5. 1999 technical progress report

    International Nuclear Information System (INIS)

    2000-01-01

    This report presents the on-going research and development projects of the Philippine Nuclear Research Institute (PNRI) in the fields of agriculture, environment and industry, scientific and technological services and nuclear regulations, licensing and safeguards

  6. 1999 technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    This report presents the on-going research and development projects of the Philippine Nuclear Research Institute (PNRI) in the fields of agriculture, environment and industry, scientific and technological services and nuclear regulations, licensing and safeguards.

  7. 1996 technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    Summaries of the researches are grouped into programs as follows: research and development in food and agriculture; research and development in health, environment and industry which includes all the PNRI research projects in 1996; scientific and technological services; and the nuclear regulations, licensing and safeguards of the institute.

  8. 1997 technical progress report

    International Nuclear Information System (INIS)

    1998-01-01

    This report presents the on-going research and development projects of the Philippine Nuclear Research Institute (PNRI) in the fields of agriculture, environment and industry, scientific and technological services and nuclear regulations, licensing and safeguards

  9. Final Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    J.Y. Hwang; R.C. Greenlund

    2002-12-31

    Michigan Technological University has demonstrated major inroads in establishing the viability of utilizing aluminum smelting by-product waste materials in lightweight concrete product applications. The research identified key elements of producing various forms of lightweight concrete products through utilizing various procedures and mixture components with the by-product materials. A process was developed through pilot plant testing that results in additional aluminum recovery at finer sizes, a clean returnable salt product through spray drying technology, and a low-salt-content oxide product with enough aluminum metal content that it can be used to form lightweight cementitious mixtures. Having three distinct products aids in generating favorable process economics. Revenue projections from aluminum recovery and salt recovery are enough to cover processing costs and create a cost-free oxide product to market for lightweight concrete applications. This supply side commercialization strategy offers aluminum by-product recyclers a potentially no cost product, which has been demonstrated through this project to create desirable and marketable lightweight concrete products of various forms. Environmental benefits to the public are tremendous. At best, all dross and salt cake materials have the potential to be completely recycled and utilized. At worst, disposal sites would see a reduced amount of material: a post processed oxide product with little salt and no hydrogen sulfide or ammonia gas generating capability, which, if isolated from high alkali conditions, would pose no reactivity concerns. The US aluminum industry has historically, along with the steel industry, been a leader in recycling metal. The findings from this project, increased metal recovery, improved salt recycling, and demonstrated end uses for oxide residues, will go a long way in helping the aluminum industry obtain 100% material utilization and zero discharge.

  10. 1995 technical progress report

    International Nuclear Information System (INIS)

    1997-01-01

    Summaries of the researches are grouped into programs as follows: research and development which covers all the PNRI research projects in 1994; scientific and technological services; and the nuclear regulations, licensing and safeguards of the institute

  11. Technical Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    Paul D. Ronney

    2004-08-26

    An ignition source was constructed that is capable of producing a pulsed corona discharge for the purpose of igniting mixtures in a test chamber. The corona generator can also be used as the ignition source for one cylinder on a test engine. The first tests were performed in a cylindrical shaped chamber to study the characteristics of the corona and analyze various electrode geometries. Next a test chamber was constructed that closely represented the dimensions of the combustion chamber of the test engine at USC. Combustion tests were performed in this chamber and various electrode diameters and geometries were tested. Higher peak pressures and faster pressure rise times were realized consistently in all test chambers versus standard spark plug ignition. A test engine was purchased for the project that has two spark plug ports per cylinder to The data acquisition and control system hardware for the USC engine lab was updated with new equipment. New software was also developed to perform the engine control and data acquisition functions including cylinder pressure monitoring. A ceramic corona electrode has been designed that fits in the new test engine and is capable of withstanding the pressures and temperatures encountered inside the combustion chamber. The corona ignition system was tested on the engine and an increase in both peak pressure and IMEP were seen in the initial test. There are issues that must be addressed before on-engine testing can continue such as EMF interference from the corona generator and electrical insulation on portions of the piston and cylinder head to prevent arcing. The EMF issue can be solved with proper shielding and grounding and various ceramic coatings are being researched for electrical insulation.

  12. Technical Progress Report

    International Nuclear Information System (INIS)

    Engelhardt, G.R.; MacDonald, D.D.

    1999-01-01

    During the past quartile (two month period) most attention has been concentrated on the problem of definition critical temperature at which ''wet'' corrosion first became operable. It has been shown that, in principle, ''wet'' corrosion processes can not be ignored for Yucca Mountain, even for initial times, when the temperature of the surface of containers is well above the boiling temperature of water for the prevailing conditions. This is because the surfaces are covered by highly hydrophilic oxides (e.g. Fe 2 O 3 , NiO, Cr 2 O 3 ) that will hydrate to the form of corresponding hydroxides, which are proton conductors, at least when in the ''wet'' condition. Because proton conduction and the presence of ''bound'' water are all that are required for the external environment to support metallic corrosion in either its general or localized form. Thus, the temperature of dehydration of the hydroxide, e.g. M(OH) 2 → MO + H 2 O(g), is a better criterion for the upper temperature limit for ''wet'' corrosion than is the boiling temperature of ''bulk'' water. During this first task, we have reviewed the existing thermodynamic data base for the dehydration of metal hydroxides and analytical expressions have been developed that allow the upper temperature limit to be estimated

  13. A new immobilized biomass technical adsorbent for uranium recovery from bioleach solutions in the mine

    International Nuclear Information System (INIS)

    Tsezos, Marios; Noh, S.H.

    1988-01-01

    A new type of metal adsorbent has been developed using inactive microbial biomass as the raw material. The adsorbent can be made to a desirable particle size. The particles have good mechanical strength and resistance to compression and consequently can be used in a packed bed resulting in a low pressure drop. The new biosorbents have been shown to maintain well the biosorptive properties of the immobilized biomass used for their production. We have tested successfully the new biosorbents for the recovery of uranium from actual bioleach solutions. (author)

  14. Ownership of solution and and evolved gas: Technical and legal perspectives

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, M. R. [Applied Reservoir Engineering and Evaluation (Canada); Friesen, J. G. [McCarthy Tetrault (Canada)

    1995-05-01

    A recent judgement of the Alberta Court of Appeal in `Prism Petroleum Ltd. et al vs. Omega Hydrocarbons Ltd.` affirmed earlier decisions, but failed to to resolve engineering issues such as terminology, PVT behaviour, producing mechanisms, the significance of an initial GOR, gas evolution in reservoirs, classification of oil and gas wells, concurrent production, enhanced recovery requirements, solution gas conservation and the effects of offset production. Some uncertainty also remained regarding the interpretation of the wording of the lease, responsibilities for costs of drilling, completion, surface facilities, operations where there has been a trespass, unjust enrichment, estoppel and limitation periods. The uncertainties regarding these legal and engineering concerns were addressed.

  15. Progress in high-efficient solution process organic photovoltaic devices fundamentals, materials, devices and fabrication

    CERN Document Server

    Li, Gang

    2015-01-01

    This book presents an important technique to process organic photovoltaic devices. The basics, materials aspects and manufacturing of photovoltaic devices with solution processing are explained. Solution processable organic solar cells - polymer or solution processable small molecules - have the potential to significantly reduce the costs for solar electricity and energy payback time due to the low material costs for the cells, low cost and fast fabrication processes (ambient, roll-to-roll), high material utilization etc. In addition, organic photovoltaics (OPV) also provides attractive properties like flexibility, colorful displays and transparency which could open new market opportunities. The material and device innovations lead to improved efficiency by 8% for organic photovoltaic solar cells, compared to 4% in 2005. Both academic and industry research have significant interest in the development of this technology. This book gives an overview of the booming technology, focusing on the solution process fo...

  16. Progress of research on the influence of alkaline cation and alkaline solution on bentonite properties

    International Nuclear Information System (INIS)

    Ye Weimin; Zheng Zhenji; Chen Bao; Chen Yonggui

    2011-01-01

    Based on the previous laboratory studies and numerical simulation on bentonite in alkaline environments, the effects of alkaline cation and alkaline solution on mineral composition, microstructure, swelling capacity and hydraulic properties of bentonite are emphasized in this paper, temperature, pH values and concentration are discussed as main affecting factors. When bentonite is exposed to alkaline cation or alkaline solution, microstructure of bentonite will be changed due to the dissolution of montmorillonite and the formation of secondary minerals, which results in the decrease of swelling pressure. The amount of the reduction of swelling pressure depends on the concentration of alkaline solution. Temperature, polyvalent cation, salinity and concentration are the main factors affecting hydraulic properties of bentonite under alkaline conditions. Therefore, future research should focus on the mechanism of coupling effects of weak alkaline solutions on the mineral composition, microstructure, swelling capacity and hydraulic properties of bentonite under different temperatures and different pH values. (authors)

  17. On solutions in arithmetic progressions to homogenous systems of linear equations

    DEFF Research Database (Denmark)

    Jensen, Jonas Lindstrøm

    We consider subsets of the natural numbers that contains infinitely many aritmetic progressions (APs) of any given length - such sets will be called AP-sets and we know due to the Green-Tao Theorem that the primes is an AP-set. We prove that the equation where is an integer matrix whose null space...

  18. The solubilities of significant organic compounds in HLW tank supernate solutions -- FY 1995 progress report

    International Nuclear Information System (INIS)

    Barney, G.S.

    1996-01-01

    At the Hanford Site organic compounds were measured in tank supernate simulant solutions during FY 1995. This solubility information will be used to determine if these organic salts could exist in solid phases (saltcake or sludges) in the waste where they might react violently with the nitrate or nitrite salts present in the tanks. Solubilities of sodium glycolate, succinate, and caproate salts; iron and aluminum and butylphosphate salts; and aluminum oxalate were measured in simulated waste supernate solutions at 25 degree C, 30 degree C, 40 degree C, and 50 degree C. The organic compounds were selected because they are expected to exist in relatively high concentrations in the tanks. The solubilities of sodium glycolate, succinate, caproate, and butylphosphate in HLW tank supernate solutions were high over the temperature and sodium hydroxide concentration ranges expected in the tanks. High solubilities will prevent solid sodium salts of these organic acids from precipitating from tank supernate solutions. The total organic carbon concentrations (YOC) of actual tank supernates are generally much lower than the TOC ranges for simulated supernate solutions saturated (at the solubility limit) with the organic salts. This is so even if all the dissolved carbon in a given tank and supernate is due to only one of these eight soluble compounds (an unlikely situation). Metal ion complexes of and butylphosphate and oxalate in supernate solutions were not stable in the presence of the hydroxide concentrations expected in most tanks. Iron and aluminum dibutylphosphate compounds reacted with hydroxide to form soluble sodium dibutylphosphate and precipitated iron and aluminum hydroxides. Aluminum oxalate complexes were also not stable in the basic simulated supernate solutions. Solubilities of all the organic salts decrease with increasing sodium hydroxide concentration because of the common ion effect of Na+. Increasing temperatures raised the solubilities of the organic

  19. Risk assessment and modeling of technical solutions for filtrations earth dams

    Directory of Open Access Journals (Sweden)

    Michael Álvarez González

    2017-12-01

    Full Text Available The paper presents the evaluation and the analysis of three types of filter geometry to evaluate the filtration risk in Zaza Reservoir, taking as starting point the historic characteristics of the fluctuation of water levels inside the earth dam. The work is based on the experience of a multidisciplinary team and previous research with bi-dimensional models, using the Finite Elements Method for the solution of basic engineering problems. Also, the results of the installation of a new filter system with a geospatial index are evaluated (under criteria of threats, vulnerability, and risk with spatial visualization data in a Geographical Information System for thematic maps generation, that represent how much the water level varies inside the dam according to the different filters evaluated.

  20. Selection of rational technical solutions in designing a robotized assembly complex

    International Nuclear Information System (INIS)

    Petrov, B.M.; Rasulbekov, R.I.

    1984-01-01

    One of the methods permitting a more objective approach to decision making in design is the method of ordered search which, in combination with the methods of expert estimate was used in designing the robotized assembly-finishing complex for automobile tires. The assembly-finishing complex consists of a number of functionally independent parts, i.e., modules provided with manipulators and mutually connected by a transport system with intermediate storage. The modified method of ordered search, examined in the present work, was therefore used for each module separately, and not for the complex as a whole. We will examine the main principles of our approach to the selection of design solutions for the example of a module for laying on the bottom-cushion cords

  1. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol 11, No. 1 through Vol. 16, No. 6

    International Nuclear Information System (INIS)

    Cottrell, W.B.; Klein, A.

    1976-04-01

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970) through Vol. 16, No. 6 (Nov.-Dec. 1975). Included in the index is a chronological list of articles (including abstract) followed by both a KWIC index and an Author Index. Nuclear Safety is a bimonthly technical progress review prepared by the Nuclear Safety Information Center and covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 300 technical articles in the last six years of publication

  2. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author. Vol. 11(1)--Vol. 18(6)

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W.B.; Klein, A.

    1978-04-11

    This index to Nuclear Safety covers articles published in Nuclear Safety, Vol. 11, No. 1 (January-February 1970), through Vol. 18, No. 6 (November-December 1977). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 450 technical articles published in Nuclear Safety in the last eight years are listed in this index.

  3. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author, Volume 18 (1) through Volume 22 (6)

    International Nuclear Information System (INIS)

    Cottrell, W.B.; Passiakos, M.

    1982-06-01

    This index to Nuclear Safety covers articles published in Nuclear Safety, Volume 18, Number 1 (January-February 1977) through Volume 22, Number 6 (November-December 1981). The index is divided into three section: a chronological list of articles (including abstracts), a permuted-title (KWIC) index, and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. Over 300 technical articles published in Nuclear Safety in the last 5 years are listed in this index

  4. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol 11, No. 1 through Vol. 16, No. 6

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W.B.; Klein, A.

    1976-04-01

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970) through Vol. 16, No. 6 (Nov.-Dec. 1975). Included in the index is a chronological list of articles (including abstract) followed by both a KWIC index and an Author Index. Nuclear Safety is a bimonthly technical progress review prepared by the Nuclear Safety Information Center and covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 300 technical articles in the last six years of publication.

  5. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author, Volume 18 (1) through Volume 22 (6)

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, W.B.; Passiakos, M.

    1982-06-01

    This index to Nuclear Safety covers articles published in Nuclear Safety, Volume 18, Number 1 (January-February 1977) through Volume 22, Number 6 (November-December 1981). The index is divided into three section: a chronological list of articles (including abstracts), a permuted-title (KWIC) index, and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. Over 300 technical articles published in Nuclear Safety in the last 5 years are listed in this index.

  6. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author. Vol. 11(1)--Vol. 18(6)

    International Nuclear Information System (INIS)

    Cottrell, W.B.; Klein, A.

    1978-01-01

    This index to Nuclear Safety covers articles published in Nuclear Safety, Vol. 11, No. 1 (January-February 1970), through Vol. 18, No. 6 (November-December 1977). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 450 technical articles published in Nuclear Safety in the last eight years are listed in this index

  7. Automated Synthesis of 68Ga-DOTA-TOC: Methodological Aspects and Suitable Technical Solutions for a Cationic Purification System.

    Science.gov (United States)

    Uccelli, Licia; Boschi, Alessandra; Cittanti, Corrado; Martini, Petra; Lodi, Luca; Zappaterra, Elisa; Romani, Simona; Zaccaria, Samanta; Cecconi, Davide; Rambaldi, Ilaria; Santi, Ivan; Panareo, Stefano; Giganti, Melchiore; Bartolomei, Mirco

    2018-05-08

    The PET Gallium-68 isotope has the advantage of being produced from a generator, so it is also available in nuclear medicine departments without a cyclotron. The preparation of Ga-68 DOTA-labelled compounds is actually performed by remotely controlled automated systems developed in order to assure production efficiency, reproducibility of the results, guarantee fast reaction time, to facilitate the synthesis and minimize the radiation exposure. Many automatic synthesis systems are available on the radiopharmaceutical market, and each of these requires the realization of some technical adaptations for routine use. We reported the Ga-68 DOTATOC production by automated cassette-based theranostic synthesizer system used in combination with a disposable GMP grade cassette system for cationic purification. The synthesizer is integrated with the 68Ge/68Ga generator systems and it allows to perform elution, eluate purification and radiolabeling in about 38 minutes. We have performed between January 2016 and January 2017 over 100 [68Ga]Ga-DOTA-TOC preparation and of these only three have failed. The average synthesis yield of radiopharmaceutical production was 54.4 ± 2.3 % and the average radiochemical purity was 96.94 ± 0.74 %. The methodology and the technical solutions adopted have allowed to obtain a high quality radiopharmaceutical product as required by the European Pharmacopoeia. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

  8. Pyrite Iron Sulfide Solar Cells Made from Solution Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Law, Matt [Univ. of California, Irvine, CA (United States)

    2017-03-21

    This document summarizes research done under the SunShot Next Generation PV II project entitled, “Pyrite Iron Sulfide Solar Cells Made from Solution,” award number DE-EE0005324, at the University of California, Irvine, from 9/1/11 thru 11/30/16. The project goal was to develop iron pyrite (cubic FeS2) as an absorber layer for solution-processible p-n heterojunction solar cells with a pathway to >20% power conversion efficiency. Project milestones centered around seven main Tasks: (1) make device-quality pyrite thin-films from solar ink; (2) develop an ohmic bottom contact with suitable low resistivity; (3) produce a p-n heterojunction with VOC > 400 mV; (4) make a solar cell with >5% power conversion efficiency; (5) use alloying to increase the pyrite band gap to ~1.2-1.4 eV; (6) produce a p-n heterojunction with VOC > 500 mV; and finally (7) make a solar cell with >10% power conversion efficiency. In response to project findings, the Tasks were amended midway through the project to focus particular effort on passivating the surface of pyrite in order to eliminate excessively-strong surface band bending believed to be responsible for the low VOC of pyrite diodes. Major project achievements include: (1) development and detailed characterization of several new solution syntheses of high-quality thin-film pyrite, including two “molecular ink” routes; (2) demonstration of Mo/MoS2 bilayers as good ohmic bottom contacts to pyrite films; (3) fabrication of pyrite diodes with a glass/Mo/MoS2/pyrite/ZnS/ZnO/AZO layer sequence that show VOC values >400 mV and as high as 610 mV at ~1 sun illumination, although these high VOC values ultimately proved irreproducible; (4) established that ZnS is a promising n-type junction partner for pyrite; (5) used density functional theory to show that the band gap of pyrite can be increased from ~1.0 to a more optimal 1.2-1.3 eV by alloying with oxygen; (6) through extensive measurements of ultrahigh

  9. GPHS-RTGs in support of the Cassini Mission. Semi annual technical progress report, 1 April 1996--29 September 1996

    International Nuclear Information System (INIS)

    1996-01-01

    This technical progress report discusses work on the Radioisotope Generators and Ancillary Activities for the Cassini spacecraft. The Cassini spacecraft is expected to launch in October 1997, and will explore Saturn and its moons. This progress report discusses issues in: spacecraft integration and liason, engineering support, safety, qualified unicouple fabrication, ETG fabrication and testing, ground support equipment, RTG shipping and launch support, designs, reviews and mission application. Safety analysis of the RTGs during reentry and launch accidents are covered. This report covers the period of April 1 to September 29, 1996

  10. Irradiation-induced precipitation and solute segregation in alloys. Fourth annual progress report, February 1, 1981-March 31, 1982

    International Nuclear Information System (INIS)

    Ardell, A.J.

    1982-04-01

    The studies of irradiation-induced solute segregation (IISS) and irradiation-induced precipitation (IIP) in Ni-Si and Pd-Fe alloys have been completed. Progress is reported for several other projects: irradiation damage in binary Pd-Cr, -Mn and -V alloys (15 at. %); IIP in Pd-Mo and Pd-W alloys; IIP in Pd-25 at. % Cr alloy; and irradiation damage effects in proton-bombarded metallic glasses (Ni-65 Zr, 40 Fe 40 Ni 14 P6B). 27 figures

  11. Technical solutions for mitigating adverse impacts on the environment implemented at Deva Thermal Power Plant

    International Nuclear Information System (INIS)

    Vaida, Victor; Egyed, Francisc; Manea, Laurean

    2004-01-01

    Situated at the south-west of Transylvania, 9 km from Deva town on the Mures River bank, Deva Power Plant has an installed capacity of 1260 MW, in six 210 MW generation units. Each unit operates with two steam boilers of 330 t/h, and steam rated parameters are 13.72 MPa and 550 deg C. The generated electricity is delivered in the national grid at voltage levels of 200 and 400 kV; there exists also the possibility of delivering electricity to the neighbouring countries through the power line Sibiu - Arad - Szeged. The Power Plant also produces thermal energy. The total installed thermal capacity is 400 MWt. Deva Power Plant was commissioned in three stages. During the first stage, between 1969 and 1971, Units No. 1, 2, 3 and 4 were commissioned, followed by Unit No. 5 in 1977 and by Unit No. 6 in 1980. All main equipment was manufactured in Russia. The main fuel utilised here is hard coal extracted from Valea Jiului basins, with calorific value between 14600 and 18800 kJ/kg. Natural gas is used as a flame support fuel. Deva Power Plant has actually produced 9% to 12% of the total electricity produced in the country and 18% to 25% of the electricity produced on coal. Continuous efforts have been made for the rehabilitation and modernisation of this power plant aiming to improve operational safety whilst equal interest has been paid to mitigating the environmental damage caused by the great size combustion systems. In this paper we present some of the preoccupations concerning earliest as well as prospective actions to be taken to protect the environment and to comply with the relevant standards and laws in force. The major role played by Deva Power Plant within the National Power Grid secured through reliable and steady operation also means undertaking exceptional environmental protection actions, to comply with current requirements. By its comprehensive modernisation programme already in progress, Deva Power Plant focus on the continuous upgrading of their plant in

  12. Overview of progress in European medium sized tokamaks towards an integrated plasma-edge/wall solution

    OpenAIRE

    Meyer, H.; Eich, T.; Beurskens, M.N.A.; Coda, S.; Hakola, A.; Martin, P.; Adamek, J.; Agostini, M.; Aguiam, D.; Ahn, J.; Aho-Mantila, L.; Akers, R.; Albanese, R.; Aledda, R.; Alessi, E.

    2017-01-01

    Integrating the plasma core performance with an edge and scrape-off layer (SOL) that leads to tolerable heat and particle loads on the wall is a major challenge. The new European medium size tokamak task force (EU-MST) coordinates research on ASDEX Upgrade (AUG), MAST and TCV. This multi-machine approach within EU-MST, covering a wide parameter range, is instrumental to progress in the field, as ITER and DEMO core/pedestal and SOL parameters are not achievable simultaneously in present day de...

  13. Mechanism of pitting corrosion prevention by nitrite in carbon steel exposed to dilute salt solutions. 1998 annual progress report

    International Nuclear Information System (INIS)

    Zapp, P.E.; Zee, J. van.

    1998-01-01

    'The overall goal of this project is to develop a fundamental understanding of the role of nitrite in preventing the breakdown of protective oxide(s) on carbon steel and the onset of pitting. Pitting corrosion of carbon steel exposed to dilute alkaline salt solutions can be induced by nitrate, sulfate, and chloride ions and is prevented by sufficient concentration of nitrite. A significant example of this material/electrolyte system is the storage and processing of DOE''s high-level radioactive liquid waste in carbon steel tanks. Added nitrite in the waste has a considerable downstream impact on the immobilization of the waste in a stable glass form. Waste tank integrity and glass production efficiency may benefit from the fundamental understanding of nitrite''s role in preventing pitting. This report summarizes progress after approximately six months of effort in this three-year EMSP project. Initial experimental and theoretical work has focused on the electrochemical behavior of carbon steel in simplified non-radioactive solutions that simulate complex dilute radioactive waste solutions. These solutions contain corrosion-inducing species such as nitrate and chloride and the corrosion-inhibiting nitrite at moderately alkaline pHs. The electrochemical behavior of interest here is that of the open-circuit potential of the steel specimen at equilibrium in the experimental electrolyte and the measures of the steel''s passivity and passivity breakdown.'

  14. 2012 Gordon Research Conference on Water and Aqueous Solutions, Final Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    Ben-Amotz, Dor [Purdue Univ., West Lafayette, IN (United States)

    2012-08-17

    Understanding the fundamental principles governing the structure and dynamics of water - and particularly how water mediates chemical interactions and processes - continues to pose formidable challenges and yield abundant surprises. The focus of this Gordon Research Conference is on identifying key questions, describing emerging understandings, and unveiling surprising discoveries related to water and aqueous solutions. The talks and posters at this meeting will describe studies of water and its interactions with objects such as interfaces, channels, electrons, oils, ions, and proteins; probed using optical, electrical, and particle experiments, and described using classical, quantum, and multi-scale theories.

  15. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 1. Geological environment of Japan

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, the part 1 of the progress report, describes first in detail the role of geological environment in high-level radioactive wastes disposal, the features of Japanese geological environment, and programs to proceed the investigation in geological environment. The following chapter summarizes scientific basis for possible existence of stable geological environment, stable for a long period needed for the HLW disposal in Japan including such natural phenomena as volcano and faults. The results of the investigation of the characteristics of bed-rocks and groundwater are presented. These are important for multiple barrier system construction of deep geological disposal. The report furthermore describes the present status of technical and methodological progress in investigating geological environment and finally on the results of natural analog study in Tono uranium deposits area. (Ohno, S.)

  16. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. An extra issue: background of the geological disposal

    International Nuclear Information System (INIS)

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, an extra issue of the progress report, was prepared for the expected readers of the report to have background information on the geological disposal. Thus it gives information about (1) generation of high-level radioactive wastes, (2) history of plans proposed for HLW disposal in Japan, and (3) procedure until the geological disposal plan is finally adopted and basic future schedules. It further discusses on such problems in HLW treatment and disposal, as for example a problem of reliable safety for a very long period. (Ohno, S.)

  17. Children’s Allocation of Study Time during the Solution of Raven’s Progressive Matrices

    Directory of Open Access Journals (Sweden)

    Patrick Perret

    2018-02-01

    Full Text Available The acuity of reasoning on Raven’s Progressive Matrices is strongly influenced by strategic determinants. Building on metamemory studies that highlight the influence of study-time allocation on memory development, we investigated children’s allocation of study time while solving these matrices. A total of 170 children aged 6–12 years completed a computerized short-form version of the standard matrices featuring items selected to represent a broad range of difficulties. Beyond analyzing changes in mean latencies and performances with age, we used generalized additive mixed models to explore within-participant variability in response times as a function of both item complexity and overall individual efficiency. Results revealed that individual differences in performances were significantly associated with children’s adaptive modulation of response times. Mediation analysis further indicated that response-time modulation contributed to age-related changes in performance. Taking account of study-time allocation in reasoning tasks may open up new avenues for the study of reasoning development and the assessment of intellectual functioning.

  18. Modern technical solutions of gas-fired heating devices of household and communal use and analysis of their testing

    Energy Technology Data Exchange (ETDEWEB)

    Bodzon, L.; Radwan, W. [Oil Mining and Gas Engineering Institute, Cracow (Poland)

    1995-12-31

    A review of technical solutions for gas-fired heating devices for household and communal use in Poland is presented. Based upon the analysis it is stated that the power output of Polish and foreign boilers ranges between 9 and 35 kW. The carbon monoxide content in flue gases reaches (on average) 0.005 vol.%, i.e., it is much lower than the maximum permissible level. Temperature of flue gases (excluding condensation boilers and those with air-tight combustion chamber) ranges between 150 and 200{degrees}C and their heating efficiency reaches 87-93%. The best parameters are given for condensation boilers, however they are still not widespread in Poland for the high cost of the equipment and assembling works. Among the heaters, the most safe are convection devices with closed combustion chamber; their efficiency is also the highest. Thus, it is concluded that a wide spectrum of high efficiency heating devices with good combustion parameters are available. The range of output is sufficient to meet household and communal requirement. They are however - predominantly - units manufactured abroad. It is difficult to formulate the program aimed at the improvement of the technique of heating devices made in Poland, and its implementation is uncertain because the production process is broken up into small handicraft workshops.

  19. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Introductory part and summaries

    International Nuclear Information System (INIS)

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan and comprises seven chapters. Chapter I briefly describes the importance of HLW management in promoting nuclear energy utilization. According to the long-term program, the HLW separated from spent fuels at reprocessing plants is to be vitrified and stored for a period of 30 to 50 years to allow cooling, then be disposed of in a deep geological formation. Chapter II mainly explains the concepts of geological disposal in Japan. Chapters III to V are devoted to discussions on three important technical elements (the geological environment of Japan, engineering technology and safety assessment of the geological disposal system) which are necessary for reliable realization of the geological disposal concept. Chapter VI demonstrates the technical ground for site selection and for setup of safety standards of the disposal. Chapter VII summarizes together with plans for future research and development. (Ohno, S.)

  20. Investigations of nuclear structure and nuclear reactions induced by complex projectiles. Technical progress report, November 1, 1978-October 31, 1979

    International Nuclear Information System (INIS)

    Sarantites, D.G.

    1979-01-01

    Experimental research on nuclear structure and reactions both published and in progress is summarized. Included are fusion reactions, strongly damped heavy ion collisions, and nuclear structure at high angular momentum. A list of publications is included

  1. Effect of point defects on mechanical properties of metals. Technical progress report, January 1, 1978--November 30, 1978

    International Nuclear Information System (INIS)

    Meshii, M.

    1978-11-01

    Progress is reported on deformation behavior of niobium single crystals below 77 0 K, the effect of electron irradiation on the deformation behavior of niobium single crystals, and surface film softening phenomenon in Ni plated iron single crystals

  2. New York City School Survey 2008-2010: Assessing the Reliability and Validity of a Progress Report Measure. Technical Appendices

    Science.gov (United States)

    Nathanson, Lori; Cole, Rachel; Kemple, James J.; Lent, Jessica; McCormick, Meghan; Segeritz, Micha

    2013-01-01

    The Research Alliance for New York City Schools examined Department of Education (DOE) School Survey data from 2008-2010 to better understand the richness and complexities of the information elicited by the Survey from parents, students, and teachers. This document provides the appendices to the technical report "New York City School Survey…

  3. Technical basis for the ITER-FEAT outline design. Progress in resolving open design issues from the outline design report

    International Nuclear Information System (INIS)

    2000-01-01

    In this publication the technical basis for the ITER-FEAT outline design is presented. It comprises the Plant Design Specifications, the Safety Principles and Environmental Criteria, the Site Requirements and Site Design Assumptions. The outline of the key features of the ITER-FEAT design includes main physical parameters and assessment, design overview and preliminary safety assessment, cost and schedule

  4. GPHS-RTGs in support of the Cassini mission. Semi annual technical progress report, 2 October 1995--31 March 1996

    International Nuclear Information System (INIS)

    1996-01-01

    The technical progress achieved during the period 2 October 1995 through 31 March 1996 on Contract No. DE-AC03-91SF18852, Radioisotope Generators and Ancillary Activities is described herein. This report is organized by the program task structure as follows: spacecraft integration and liaison; engineering support; safety; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; contract acquired government-owned property (CAGO) acquisition; and program calendars

  5. Silicon ribbon growth by a capillary action shaping technique. Annual report (Quarterly technical progress report No. 9)

    Energy Technology Data Exchange (ETDEWEB)

    Schwuttke, G.H.; Ciszek, T.F.; Kran, A.

    1977-10-01

    Progress on the technological and economical assessment of ribbon growth of silicon by a capillary action shaping technique is reported. Progress in scale-up of the process from 50 mm to 100 mm ribbon widths is presented, the use of vitreous carbon as a crucible material is analyzed, and preliminary tests of CVD Si/sub 3/N/sub 4/ as a potential die material are reported. Diffusion length measurements by SEM, equipment and procedure for defect display under MOS structure in silicon ribbon for lifetime interpretation, and an assessment of ribbon technology are discussed. (WHK)

  6. Association Euratom - Risø National Laboratory for Sustainable Energy, Technical University of Denmark - Annual Progress Report 2009

    DEFF Research Database (Denmark)

    Korsholm, Søren Bang; Michelsen, Poul; Juul Rasmussen, Jens

    The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its...... superconductors. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2009....

  7. Association Euratom - Risø National Laboratory for Sustainable Energy, Technical University of Denmark - Annual Progress Report 2008

    DEFF Research Database (Denmark)

    Korsholm, Søren Bang; Michelsen, Poul; Juul Rasmussen, Jens

    The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its...... been initiated in 2008. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2008....

  8. Studies in chemical dynamics and radiation chemistry. Technical progress report, 1 July 1974--30 June 1975

    International Nuclear Information System (INIS)

    Kuppermann, A.

    1975-01-01

    Research progress in the following areas is reported: low energy electron scattering; photoelectron spectrometry; elementary reactions by photolysis at variable wavelengths; collisions in crossed molecular beams; and, diffusion kinetics in the radiation chemistry of water. Publications related to the work are included. (JGB)

  9. Sodium boiling detection in LMFBRs (Phase I). 5th quarterly technical progress report, July 1, 1975--October 31, 1975

    International Nuclear Information System (INIS)

    Albrecht, R.W.; McCormick, N.J.

    1975-01-01

    Progress summarized includes the design of a gamma heated subassembly for sodium boiling experiments and an experiment showing that neutronic noise and acoustic noise caused by sodium boiling are highly correlated in a wide frequency band about the bubble repetition frequency

  10. Effects of Water Radiolysis in Water Cooled Reactors - Nuclear Energy Research Initiative (NERI) Program. Technical Progress Report

    International Nuclear Information System (INIS)

    Pimblott, S.M.

    2000-01-01

    OAK B188 Quarterly Progress Report on NERI Proposal No.99-0010 for the Development of an Experiment and Calculation Based Model to Describe the Effects of Radiation on Non-standard Aqueous Systems Like Those Encountered in the Advanced Light Water Reactor

  11. Effects of humic substances on the migration of radionuclides: complexation and transport of actinides. First technical progress report (work period 01.97 - 12.97)

    International Nuclear Information System (INIS)

    Buckau, G.

    1998-08-01

    The present report describes progress within the first year of the EC-project 'Effects of Humic Substances on the Migration of Radionuclides: Complexation and Transport of Actinides'. The project is conducted within the EC-Cluster 'Radionuclide Transport/Retardation Processes'. Contrary to formal requirements of the Commission, this report with a great deal of detail is established already after one year of project work. It is scheduled to be followed by a second technical progress report covering the second year of the project. In agreement with the contractual obligations a final report of similar technical detail will also be generated. The report contains an executive summary written by the coordinator (FZK/INE) with strong support from the other three task leaders (BGS, CEA-SGC and RMC-E). More detailed results are given by individual contributions of the project partners in 13 annexes. In the executive summary report the origin of results presented is given, also serving as guidance for finding more detailed results in the annexes. Not all results are discussed or referred to in the executive summary report and thus readers with a deeper interest also need to consult the annexes. (orig.)

  12. A systematic assessment of the state of hazardous waste clean-up technologies. Quarterly technical progress report, April 1--June 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Berg, M.T.; Reed, B.E.; Gabr, M.

    1993-07-01

    West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Report for Year 1 of the Agreement. This report reflects the progress and/or efforts performed on the following nine technical projects encompassed by the Year 1 Agreement for the period of April 1 through June 30, 1993: Systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies -- drain-enhanced soil flushing (DESF) for organic contaminants removal; site remediation technologies -- in situ bioremediation of organic contaminants; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors -- monolayer and multilayer self-assembled films for chemical sensors; Winfield lock and dam remediation; Assessments of Technologies for hazardous waste site remediation -- non-treatment technologies and pilot scale test facility implementation; and remediation of hazardous sites with stream reforming.

  13. An approach to knowledge structuring for advanced phases of the Technical and Management Information System (TMIS)

    Science.gov (United States)

    Goranson, H. T.

    1986-01-01

    The Technical and Management Information System (TMIS) must employ on enlightened approach to its object structure, but basic issues in conceptual structuring remain to be resolved. Sirius outlines the necessary agenda and reports on progress toward solutions.

  14. Prize of the German gas-supply industry: Technical solutions poor cousin of the prize distribution. Preis der deutschen Gaswirtschaft: Handwerkliche Loesungen Stiefkinder der Preisvergabe

    Energy Technology Data Exchange (ETDEWEB)

    Will, H.

    1991-03-01

    The German gas-supply industry annually awards particularly energy-saving and environment friendly installations. Unfortunately only little attention is paid to small technical solutions. The article presents as particularly worth mentioning the work of a hvac-company which uses a condensing boiler for water heating. With layer-storage and integration of solar energy the energy savings are as high as possible. (BWI).

  15. Diagnostic development and support of MHD test facilities: Technical progress report for the period January, February, March 1985

    International Nuclear Information System (INIS)

    Shepard, W.S.; Cook, R.L.

    1985-04-01

    Mississippi State University is developing diagnostic instruments for MHD power train data acquisition and for support of MHD component development test facilities. Microprocessor-controlled optical instruments, initially developed for HRSR support, are being refined, and new systems to measure temperatures and gas-seed-slag stream characteristics are being developed. To further data acquisition and analysis capabilities, the diagnostic systems are being interfaced with MHD Energy Center computers. Additionally, technical support of the diagnostic needs of the national MHD research effort is being provided

  16. Taxonomy of Means and Ends in Aquaculture Production—Part 2: The Technical Solutions of Controlling Solids, Dissolved Gasses and pH

    Directory of Open Access Journals (Sweden)

    Bjorgvin Vilbergsson

    2016-09-01

    Full Text Available In engineering design, knowing the relationship between the means (technique and the end (desired function or outcome is essential. The means in Aquaculture are technical solutions like airlifts that are used to achive desired functionality (an end like controlling dissolved gasses. In previous work, the authors identified possible functions by viewing aquaculture production systems as transformation processes in which inputs are transformed by treatment techniques (means and produce outputs (ends. The current work creates an overview of technical solutions of treatment functions for both design and research purposes. A comprehensive literature review of all areas of technical solutions is identified and categorized into a visual taxonomy of the treatment functions for controlling solids, controlling dissolved gasses and controlling pH alkalinity and hardness. This article is the second in a sequence of four and partly presents the treatments functions in the taxonomy. The other articles in this series present complementary aspects of this research: Part 1, A transformational view on aquaculture and functions divided into input, treatment and output functions; Part 2, The current taxonomy paper; Part 3, The second part of the taxonomy; and Part 4, Mapping of the means (techniques for multiple treatment functions.

  17. Research and development on optically pumped polarized ion sources. Technical progress report, February 1, 1985-January 31, 1986

    International Nuclear Information System (INIS)

    Anderson, L.W.

    1985-07-01

    During the past year we have studied the relaxation times in an optically pumped 23 Na vapor target, studied the effects of radiation trapping on the polarization in a Na vapor target, and have studied the effects of spin exchange collisions on a beam of fast H 0 atoms as they pass through a polarized alkali target. This research is directed toward improvements in the optically pumped Na or other alkali vapor targets used for the production of polarized H - ions. In this progress report we review the properties of the optically pumped polarized H - ion source as well as discussing the progress of our research on optically pumped Na or other alkali vapor targets. 81 refs., 9 figs

  18. Technical progress report of biological research on the Volcanic Island Surtsey and its environs for the period 1965--1978

    Energy Technology Data Exchange (ETDEWEB)

    Fridriksson, S.

    1978-01-01

    Progress is reported on the following research projects: changes in shoreline and surface of the island due to volcanic activity; colonization of microorganisms, algae, lichens, and vascular plants; introduction of insects and other arthropods by wind, water, and man; transport of invertebrates to the island by flotsam of the sea; species and nesting habits of birds on the island; behavior of seals on beaches of the island; and future trends of Surtsey ecosystems. (HLW)

  19. Research proposal and annual report No. 16. Part B. Technical progress, September 1, 1975--August 31, 1976

    Energy Technology Data Exchange (ETDEWEB)

    1976-06-01

    Progress is reported on the following research projects: RNA synthesis in yeast; regulation of nitrogen metabolism; biological toxicity of intracellular radioisotope decay; the mechanism of energy conversion in chloroplasts; promoting vibrations in spin-orbital coupling in vibrationally deficient molecules; electronic excitation and hydrogen bonding; macromolecular biophysics; the synthesis and maturation of RNA; electronic response properties of biomolecular systems; chromosome structure and function and chromosome damage; DNA replication and chromosome structure; and influence of phospholipids on the dynamic properties of rhodopsin. (HLW)

  20. Research proposal and annual report No. 16. Part B. Technical progress, September 1, 1975--August 31, 1976

    International Nuclear Information System (INIS)

    1976-01-01

    Progress is reported on the following research projects: RNA synthesis in yeast; regulation of nitrogen metabolism; biological toxicity of intracellular radioisotope decay; the mechanism of energy conversion in chloroplasts; promoting vibrations in spin-orbital coupling in vibrationally deficient molecules; electronic excitation and hydrogen bonding; macromolecular biophysics; the synthesis and maturation of RNA; electronic response properties of biomolecular systems; chromosome structure and function and chromosome damage; DNA replication and chromosome structure; and influence of phospholipids on the dynamic properties of rhodopsin

  1. Generalization of Bateman-Hillion progressive wave and Bessel-Gauss pulse solutions of the wave equation via a separation of variables

    CERN Document Server

    Kiselev, A

    2003-01-01

    Two new families of exact solutions of the wave equation u sub x sub x + u sub y sub y + u sub z sub z - c sup - sup 2 u sub t sub t = 0 generalizing Bessel-Gauss pulses and Bateman-Hillion relatively undistorted progressive waves, respectively are presented. In each of these families new simple solutions describing localized wave propagation are found. The approach is based on a kind of separation of variables. (letter to the editor)

  2. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 3. Safety assessment for geological disposal systems

    International Nuclear Information System (INIS)

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, the part 3 of the progress report, concerns safety assessment for geological disposal systems definitely introduced in part 1 and 2 of this series and consists of 9 chapters. Chapter I concerns the methodology for safety assessment while Chapter II deals with diversity and uncertainty about the scenario, the adequate model and the required data of the systems above. Chapter III summarizes the components of the geological disposal system. Chapter IV refers to the relationship between radioactive wastes and human life through groundwater, i.e. nuclide migration. In Chapter V is made a reference case which characterizes the geological environmental data using artificial barrier specifications. (Ohno. S.)

  3. High temperature turbine technology program. Phase II. Technology test and support studies. Annual technical progress report, January 1, 1979-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    Work performed on the High Temperature Turbine Technology Program, Phase II - Technology Test and Support Studies during the period from January 1, 1979 through December 31, 1979 is summarized. Objectives of the program elements as well as technical progress and problems encountered during this Phase II annual reporting period are presented. Progress on design, fabrication and checkout of test facilities and test rigs is described. LP turbine cascade tests were concluded. 350 hours of testing were conducted on the LP rig engine first with clean distillate fuel and then with fly ash particulates injected into the hot gas stream. Design and fabrication of the turbine spool technology rig components are described. TSTR 60/sup 0/ sector combustor rig fabrication and testing are reviewed. Progress in the design and fabrication of TSTR cascade rig components for operation on both distillate fuel and low Btu gas is described. The new coal-derived gaseous fuel synthesizing facility is reviewed. Results and future plans for the supporting metallurgical programs are discussed.

  4. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 2. Engineering technology for geological disposal

    International Nuclear Information System (INIS)

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the deep geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, part 2 of the progress report, concerns engineering aspect with reference to Japanese geological disposal plan, according to which the vitrified HLW will be disposed of into a deep, stable rock mass with thick containers and surrounding buffer materials at the depth of several hundred meters. It discusses on multi-barrier systems consisting of a series of engineered and natural barriers that will isolate radioactive nuclides effectively and retard their migrations to the biosphere environment. Performance of repository components, including specifications of containers for vitrified HLW and their overpacks under design as well as buffer material such as Japanese bentonite to be placed in between are described referring also to such possible problems as corrosion arising from the supposed system. It also presents plans and designs for underground disposal facilities, and the presumed management of the underground facilities. (Ohno, S.)

  5. Gas-Cooled Thermal Reactor Program. Annual technical progress report for the period ending September 30, 1981

    International Nuclear Information System (INIS)

    1982-03-01

    This report provides descriptions and results of the technical effort during FY81 on the Gas-Cooled Thermal Reactor Program. The FY81 work was organized according to the Work Breakdown Structure (WBS) for the National HTGR Program, and fell within five of the WBS tasks. The work on Market Definition and Development (WBS 03) was associated with estimating product costs for HTGR systems and their alternatives, projecting markets and market penetrations for these systems, and providing costs and market input to application analyses and component design. The Plant Technology (WBS 13) effort was mainly in the development of the systems dynamic computer code, STAR, for the transient analysis of HTGR's in reformer applications. The analysis of pebble bed reactors (PBR) was performed under Technology Transfer (WBS 15). The effort on components and systems within the nuclear heat source for reforming plants was performed under High Temperature Nuclear Heat Source (WBS 42)

  6. Realization of radiation-chemical processes in national economy-important stage of scientific and technical progress

    International Nuclear Information System (INIS)

    Breger, A.Kh.

    1975-01-01

    Realization of energy resourses of the atomic power engineering will greatly contribute to the scientific and technological progress. The dominat role play the radiochemical methods of properties modification applied for the well-known materials and for the production of materials with modern operating characteristics necessary for their application in different branches of industry and agriculture. Radiation modeling of products from polyolefine, wood-plastic and concrete-polymer materials are considered as well as the processes in ''thin'' units of agitating systems. The future developments and present state of the art of radiation sources are presented

  7. Committee on Atomic, Molecular, and Optical Sciences (CAMOS). Technical progress report ampersand continuation proposal, February 1, 1993--January 31, 1994

    International Nuclear Information System (INIS)

    Taylor, R.D.

    1997-01-01

    The Committee on Atomic, Molecular and Optical Sciences (CAMOS) of the National Research Council (NRC) is charged with monitoring the health of the field of atomic, molecular, and optical (AMO) science in the United States. Accordingly, the Committee identifies and examines both broad and specific issues affecting the field. Regular meetings, teleconferences, briefings from agencies and the scientific community, the formation of study panels to prepare reports, and special symposia are among the mechanisms used by the CAMOS to meet its charge. This progress report presents a review of CAMOS activities from February 1, 1993 to January 31, 1994. The details of prior activities are discussed in earlier progress reports. This report also includes the status of activities associated with the CAMOS study on the field that is being conducted by the Panel on the Future of Atomic, Molecular, and Optical Sciences (FAMOS). During the above period, CAMOS has continued to track and participate in, when requested, discussions on the health of the field. Much of the perspective of CAMOS has been presented in the recently-published report Research Briefing on Selected Opportunities in Atomic, Molecular, and Optical Sciences. That report has served as the basis for briefings to representatives of the federal government as well as the community-at-large. In keeping with its charge to monitor the health of the field, CAMOS launched a study designed to highlight future directions of the field

  8. Environmental reactions and their effects on mechanical behavior of metallic materials. Technical progress report, February 1, 1977--January 31, 1978

    International Nuclear Information System (INIS)

    Gibala, R.; Sethi, V.K.; Fournier, R.

    1977-01-01

    New results obtained in surface oxide softening of the Group VB refractory metals and mechanical behavior of Nb-H and Nb-D alloys are presented. The results include: (a) experimental verification of a model of surface oxide softening of body-centered cubic metals; (b) determination of a stress-differential effect in surface oxide softening; and (c) characterization of hydrogen and deuterium strengthening in Nb and Nb-O alloys. The second section reviews major contributions in topics on: interstitials in metals, mechanical behavior of body-centered cubic metals, solute-defect interactions and internal friction mechanisms in solids

  9. Theoretical research in intermediate-energy nuclear physics. [Technical progress report, April 1, 1993--March 31, 1994

    International Nuclear Information System (INIS)

    Seki, R.

    1994-01-01

    This paper discusses progress that has been made on the following seven problems: (1) (e, e'p) at high momentum transfer; (2) post,acceleration effects in two-nucleon interferometry of heavy-ion collisions; (3) pion-nucleus interactions above 0.5 GeV; (4) chiral symmetry breaking in nuclei and picnic atom anomaly; (5) atomic screening on nuclear astronomical reactions; (6) QCD related work (coherent pion production from skyrmion-antiskyrmion annihilation, QCD in 1 + 1 dimensions, and correlation functions in the QCD vacuum), and (7) kaonic hydrogen atom experiment. The problems deal with various topics mostly in intermediate-energy nuclear physics. We place priority on (1) and (2), and describe them somewhat in detail below. Other problems are our on-going projects, but we are placing lower priority on them in the second and third year

  10. Measurements of scattering processes in negative ion: Atom collisions. Technical progress report, 1 September 1991--31 December 1994

    International Nuclear Information System (INIS)

    Kvale, T.J.

    1994-01-01

    This report describes the progress made on the research objectives during the past three years of the grant. This research project is designed to study various scattering processes which occur in H - collisions with atomic (specifically, noble gas and atomic hydrogen) targets in the intermediate energy region. These processes include: elastic scattering, single- and double-electron detachment, and target excitation/ionization. For the elastic and target inelastic processes where H - is scattered intact, the experimental technique of Ion Energy-Loss Spectroscopy (IELS) will be employed to identify the final target state(s). In most of the above processes, cross sections are unknown both experimentally and theoretically. The measurements will provide total cross sections (TCS) initially, and once the angular positioning apparatus is installed, will provide angular differential cross sections (ADCS)

  11. Combined macroscopic and microscopic approach to the fracture of metals. Technical progress report, July 1975--June 1976

    International Nuclear Information System (INIS)

    Gurland, J.; Rice, J.R.; Asaro, R.J.; Needleman, A.

    1976-07-01

    Major studies have been started on (1) The conditions governing the localization of plastic flow at the onset of rupture. Specific calculations of critical conditions for a number of material models have been made possible through a theoretical framework by which localization is formulated as a constitutive instability, in the form of a bifurcation into a localized mode from a state of previously homogeneous deformation, and (2) The strength of interfaces with and without the presence of dissolved segregants. Criteria for brittle vs. ductile response of an interface were developed on the basis of dislocation mechanisms and thermodynamic relations, and applied to hydrogen embrittlement. Further progress has been achieved in the analysis of stress and deformation at a crack tip by the application of the large-strain elastic-plastic finite element program developed over the last two years. Work has continued on particle and sub-boundary strengthening in steels and an experimental study of fracture initiation at particles was begun

  12. Bench-scale testing of on-line control of column flotation using a novel analyzer. Third quarterly technical progress report, April 1, 1993--June 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-24

    This document contains the third quarterly technical progress report for PTI`s Bench-Scale Testing Project of a circuit integrating PTI`s KEN-FLOTETM Column Flotation Technology and PTI`s On-Line Quality Monitor and Control System. The twelve-month project involves installation and testing of a 200--300 lb/hr. bench-scale flotation circuit at PETC`s Coal Preparation Process Research Facility (CPPRF) for two bituminous coals (Upper Freeport and Pittsburgh No. 8 Seam Raw Coals). Figure 1 contains the project plan, as well as the approach to completing the major tasks within the twelve-month project schedule. The project is broken down into three phases, which include: Phase I -- Preparation: The preparation phase was performed principally at PTI`s Calumet offices from October through December, 1992. It involved building of the equipment and circuitry, as well as some preliminary design and equipment testing; Phase II -- ET Circuit Installation and Testing: This installation and testing phase of the project was performed at PETC`s CPPRF from January through June, 1993, and was the major focus of the project. It involved testing of the continuous 200--300 lb/hr. circuit; and Phase III -- Project Finalization: The project finalization phase is occurring from July through September, 1993, at PTI`s Calumet offices and involves finalizing analytical work and data evaluation, as well as final project reporting. This Third Quarterly Technical Progress Report principally summarizes the results from the benchscale testing with the second coal (Pittsburgh No. 8 Seam Coal), which occurred in April through June, 1993. It also contains preliminary economic evaluations that will go into the Final Report, as well as the plan for the final reporting task.

  13. Projects at the Western Environmental Technology Office. Quarterly technical progress report, July 1, 1995--September 30, 1995

    International Nuclear Information System (INIS)

    1996-01-01

    The goal of this project is to demonstrate the technical and economic feasibility of commercializing a biotechnology that uses plants to remediate soils, sediments, surface waters, and groundwaters contaminated by heavy metals and radionuclides. This technology, known as phytoremediation, is particularly suited to remediation of soils or water where low levels of contaminants are widespread. Project objectives are to provide an accurate estimate of the capability and rate of phytoremediation for removal of contaminants of concern from soils and groundwaters at Department of Energy (DOE) sites and to develop data suitable for engineering design and economic feasibility evaluations, including methods for destruction or final disposition of plants containing contaminants of concern. The bioremediation systems being evaluated could be less expensive than soil removal and treatment systems, given the areal extent and topography of sites under consideration and the investment of energy and money in soil-moving and -treating processes. In situ technology may receive regulatory acceptance more easily than ex situ treatments requiring excavation, processing, and replacement of surface soils. In addition, phytoremediation may be viable for cleanup of contaminated waters, either as the primary treatment or the final polishing stage, depending on the contaminant concentrations and process economics considerations

  14. Projects at the Western Environmental Technology Office. Quarterly technical progress report, July 1, 1995--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-01

    The goal of this project is to demonstrate the technical and economic feasibility of commercializing a biotechnology that uses plants to remediate soils, sediments, surface waters, and groundwaters contaminated by heavy metals and radionuclides. This technology, known as phytoremediation, is particularly suited to remediation of soils or water where low levels of contaminants are widespread. Project objectives are to provide an accurate estimate of the capability and rate of phytoremediation for removal of contaminants of concern from soils and groundwaters at Department of Energy (DOE) sites and to develop data suitable for engineering design and economic feasibility evaluations, including methods for destruction or final disposition of plants containing contaminants of concern. The bioremediation systems being evaluated could be less expensive than soil removal and treatment systems, given the areal extent and topography of sites under consideration and the investment of energy and money in soil-moving and -treating processes. In situ technology may receive regulatory acceptance more easily than ex situ treatments requiring excavation, processing, and replacement of surface soils. In addition, phytoremediation may be viable for cleanup of contaminated waters, either as the primary treatment or the final polishing stage, depending on the contaminant concentrations and process economics considerations.

  15. Involvement of Individuals in the Development of Technical Solutions and Rules of Management for Building Renovation Projects: A Case Study of Latvia

    Science.gov (United States)

    Pukite, I.; Grekis, A.; Geipele, I.; Zeltins, N.

    2017-08-01

    In March 2016, the Latvian government approved a new support program for increasing energy efficiency in residential apartment buildings. For the support of renovation of apartment buildings in the period from 2016 to 2023, 166 470 588 EUR will be available. Different persons, such as energy auditors, designers, architects, project managers and builders, will be involved in the process of planning, development and implementation of building renovation. At the development stage of the building renovation project, special attention should be devoted to the first stage - energy audit and technical project development. The problem arises due to the fact that each of these individuals, during the development of technical building documentation, does not work as a completely unified system. The implementation of construction project planning and organisational management system is one of the most important factors to guarantee that the quality of building renovation project is ensured in accordance with the laws and regulatory standards. The paper studies mutual cooperation, professionalism and the role of information feedback of personnel involved in the planning stage of building renovation, which is an essential prerequisite for the renovation process in order to achieve high quality of work and reduce the energy performance indicator. The present research includes the analysis of different technical solutions and their impact on energy efficiency. Mutual harmonisation of technical specifications is also investigated.

  16. Progress of the radioactive waste management at the Dalat Nuclear Research Institute and the role of an IAEA technical co-operation project in this process

    International Nuclear Information System (INIS)

    Nang, N.T.; Ngoc, O.V.; Nhu Thuy, T.T.; Nghi, D.V.; Thu, N.T.

    2002-01-01

    At present, the main radioactive waste generator in Vietnam is the Dalat Nuclear Research Institute (DNRI). For safe management of radioactive waste generated from this nuclear center, in 1982 Soviet specialists newly constructed one combined technology system for low level radioactive waste management. The existing system consists of two main parts, a Liquid Radioactive Waste Treatment Station and a Storage/Disposal Facility. The liquid treatment station can in principle meet the needs for this nuclear center but disposal technology and storage/disposal facilities are not good enough both with respect to safety and economy, especially the storage/disposal facility placed in Dalat, the tourist city. In order to help DNRI and Vietnam to solve the radioactive waste management problem, the IAEA Technical Co-operation (TC) project VIE/9/007 was implemented in Vietnam. The facilities and IAEA experts provided under this project gradually help to develop radioactive waste management at DNRI, Vietnam. This paper outlines progress under way in the management of the radioactive waste at the Nuclear Research Institute (NRI), Dalat, Vietnam, and the role of the IAEA Technical Co-operation (TC) project in this process. (author)

  17. Technical Vocational Education and Training for Micro-Enterprise Development in Ethiopia: A Solution or Part of the Problem?

    Science.gov (United States)

    Gondo, Tendayi; Dafuleya, Gift

    2010-01-01

    Technical vocational education and training (TVET) programmes have recently received increased attention as an area of priority for stimulating growth in developed and developing countries. This paper considers the situation in Ethiopia where the promotion of micro and small-sized enterprises (MSEs) has been central to the development and…

  18. DEVELOPMENT OF A CO2 SEQUESTRATION MODULE BY INTEGRATING MINERAL ACTIVATION AND AQUEOUS CARBONATION. ANNUAL TECHNICAL PROGRESS REPORT

    International Nuclear Information System (INIS)

    George Alexander; M. Mercedes Maroto-Valer; Parvana Aksoy; Harold Schobert

    2006-01-01

    Mineral carbonation provides a potential option for the long-term storage of carbon dioxide. Serpentine has been chosen as the feedstock mineral, due to its abundance and availability. However, the relatively low reactivity of serpentine has warranted research into physical and chemical treatments that have been shown to greatly increase its reactivity. The use of sulfuric acid as an accelerating medium for the removal of magnesium from serpentine has recently been investigated. In addition to the challenges presented by the dissolution of serpentine, another challenge is the subsequent carbonation of the magnesium ions. A stable hydration sphere for the magnesium ion reduces the carbonation kinetics by obstructing the formation of the carbonation products. Accordingly, this research has evaluated the solubility of carbon dioxide in aqueous solution, the interaction between the dissociation products of carbon dioxide, and the carbonation potential of the magnesium ion

  19. Nemaha Uplift seismotectonic study: regional tectonics and seismicity of eastern Kansas. Technical progress report, October 1, 1978-September 30, 1979

    International Nuclear Information System (INIS)

    Wilson, F.W.

    1979-11-01

    Progress and results of all work on this project to the end of its second year, or September 30, 1978, were reported in NUREG/CR-0666, published March 1979. Project third-year activites and results include the following: continued operation of a regional microearthquake monitoring network which detected and located 26 regional events between October 1, 1978, and August 2, 1979; designing and building a triggering system to allow digitized recording of microearthquakes by a modified exploration seismography; continued surface and subsurface studies of selected areas along the Nemaha Uplift-Keweenanan Mafic belt trend; continued study of Precambrian rock types from recently drilled wells; beginning compilation of a fault catalog; terrain analysis and lineament studies which indicate that the alignment of stream drainages and divides are strongly controlled by basement and subsurface structure; continued reduction of gravity data for northeastern Kansas (a Bouguer gravity map probably will be available late Fall 1979); modification of the exploration seismograph system to a more efficient 12-channel Mini-Sosie system and completion of several line-miles of reflection profiling; and beginning integration of data from Oklahoma, Nebraska, and Iowa co-investigators. All major goals for FY 1979 were accomplished. 2 figures

  20. Establishment of an Institute for Fusion Studies. Technical progress report, 1 November 1993--31 October 1994

    International Nuclear Information System (INIS)

    Hazeltine, R.D.

    1994-07-01

    The Institute for Fusion Studies is a national center for theoretical fusion plasma physics research. Its purposes are: (1) to conduct research on theoretical questions concerning the achievement of controlled fusion energy by means of magnetic confinement--including both fundamental problems of long-range significance, as well as shorter-term issues; (2) to serve as a national and international center for information exchange by hosting exchange visits, conferences, and workshops; (3) and to train students and postdoctoral research personnel for the fusion energy program and plasma physics research areas. The theoretical research results obtained by the Institute contribute to the progress of nuclear fusion research, whose goal is the development of fusion power as a basic energy source. Close collaborative relationships have been developed with other university and national laboratory fusion groups, both in the US and abroad. In addition to its primary focus on mainstream fusion physics, the Institute is also involved with research in fusion-sidestream fields, such as advanced computing techniques, nonlinear dynamics, space plasmas and astrophysics, statistical mechanics, fluid dynamics, and accelerator physics. Important research discoveries are briefly described

  1. Exotic atoms: Hadronic and muonic atoms 1969--1997. Technical progress report, February 1, 1996--August 31, 1997

    International Nuclear Information System (INIS)

    Kunselman, R.

    1997-01-01

    Since this is a terminal progress-report it is a synopsis over the total time of the grant. The author has utilized exotic hadronic and muonic atoms as tools to access information concerning questions to do with particle, nuclear, and atomic physics. The information has answered fundamental questions about lepton conservations, quark models, tests of the CPT theorem, QED energies, and nuclear structure. The present experiments involve reactions with a variety of hydrogen isotopic mixtures to form solid targets to produce muonic hydrogen isotope atoms. The method relies on muon capture by a proton and transfer of the muon from the proton to a deuteron or a triton. The resulting muonic deuterium or muonic tritium will not immediately thermalize because of the very low elastic cross sections of the Ramsauer-Townsend effect, and are emitted from the surface of the layer and escape into a vacuum region. A second solid hydrogen isotopic target is produced downstream on which the muonic hydrogen atom can react and the time of flight measured

  2. Indiana University High Energy Physics Group: Task A: Technical progress report, December 1, 1986 to November 30, 1987

    International Nuclear Information System (INIS)

    Alyea, E.D.; Brabson, B.B.; Crittenden, R.R.; Dzierba, A.R.; Martin, H.J.; Ogren, H.O.; Zieminski, A.

    1987-05-01

    Data collection on the production of the KKπ state in π - , K - , and p-bar induced reactions is reported, with partial wave analysis in progress. Work on the design of a target calorimeter and data taking for a muon scattering experiment at CERN is completed. Analysis of a fixed-target jet experiment is reported. A dimuon detector has been prepared for an experiment at Fermilab to study hadronic processes yielding high mass dimuons and associated particles. Participation in the coordination and writing of software for the DO collider detector at Fermilab is reported. Some results from the High Resolution Spectrometer (HRS) are reported, including direct observation of several decay modes of the charmed mesons, directly observed meson resonances, baryon resonances, and some discoveries concerning the tau lepton. Activity is reported in the building of hardware for the muon upgrade for the Mark2 detector at the SLC and the building of the beam position monitors for the SLC, and microprocessors for Mark2 data analysis. Involvement in the SLC polarization collaboration is also reported

  3. Intermediate-energy nuclear physics. Task C. Technical progress report, October 1, 1982-October 1, 1983. Part I

    International Nuclear Information System (INIS)

    1983-01-01

    Progress is reported on the following experimental studies: (1) excitation of giant resonances in 118 Sn in inelastic pion scattering at 130 MeV; (2) giant dipole excitations of 40 Ca by inelastic pion scattering; (3) charge symmetry test using the π + and π - elastic scattering from deuterium at 143 and 256 MeV; (4) binding energy effects on the isospin amplitudes in p-shell nuclei; (5) the energy dependence of the 14 C (π + ,π 0 ) 14 N reaction to the IAS; (6) the ( 3 He,t) reaction at 2 GeV; (7) analyzing power in the (polarized p,n) IAS transitions; (8) the excitation of the 1/2 + (2.36) MeV state in the 24Mg (polarized p,d) reaction from 27 to 150 MeV; (9) the energy dependence of the (polarized p,d) reaction for 54 Fe and 140 Ce; and (10) the energy dependence of the 7 Li(p,d) 6 Li reaction. Publications are listed

  4. Molluscs and echinoderms aquaculture: biological aspects, current status, technical progress and future perspectives for the most promising species in Italy

    Directory of Open Access Journals (Sweden)

    Antonio Pais

    2012-10-01

    Full Text Available Shellfish aquaculture is a widespread activity in the Italian peninsula. However, only two bivalve species are mainly cultured along the coastline of that country: the Mediterranean mussel Mytilus galloprovincialis and the Manila clam Venerupis philippinarum (Ruditapes philippinarum. By contrast, just a few other mollusc species of commercial interest are scarcely reared at a small-scale level. After analysing the current status of Italian shellfish production, this paper reports and discusses the potential for culturing several different invertebrate species [i.e., the European flat oyster Ostrea edulis, the grooved carpet shell Venerupis decussata (Ruditapes decussatus, the razor clams Ensis minor and Solen marginatus, the cephalopod Octopus vulgaris, and the purple sea urchin Paracentrotus lividus] in this country. In addition, a detailed overview of the progress made in aquacultural techniques for these species in the Mediterranean basin is presented, highlighting the most relevant bottlenecks and the way forward to shift from the experimental to the aquaculture phase. Finally, an outlook of the main economic and environmental benefits arising from these shellfish culture practices is also given.

  5. 1991 Technical progress report of the University of South Carolina's High Energy Physics Group, February 1990--July 1991

    International Nuclear Information System (INIS)

    1991-01-01

    The high energy physics group at the University of South Carolina includes five teaching faculty members, one research faculty member, and five graduate students. Profs. Childers, Darden, and Wilson devote most of their research effort to Fermilab experiment E789, which is designed to observe charmless two-body decays of b-flavored mesons and baryons. Prof. Wilson works on Fermilab experiment E687 which studies charm physics in the wide-band photon beam. Profs. Rosenfeld and Wang participate in the AMY collaboration, which studies electron-positron interactions using the TRISTAN collider at KEK. Prof. Rosenfeld and one student collaborate with personnel from KEK and INS, Tokyo, on an experiment to detect a 17 keV neutrino in the β-decay spectrum of 63 Ni. Members of the group also participate in Fermilab Proposal P803 which will search for the oscillation of muon neutrino to tau neutrino with sensitivity better than a factor of 40 than previously achieved and in Superconducting Super Collider activities which include the development of an imaging preradiator. A brief discussion is given on progress made for each program

  6. Identification of sulfur heterocycles in coal liquids and shale oils. Technical progress report, August 1, 1980-May 1, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Lee, M. L.; Castle, R. N.

    1981-01-01

    The sulfur heterocycle separation scheme which was described in the last progress report was evaluated for quantitative recovery of individual components. The results indicate that recoveries can range from 10% to approx. 30% depending on the structure of the compound. During this period, 23 unsubstituted sulfur-containing heterocyclic ring systems were synthesized in oder to confirm GC/MS identifications and for biological testing. The four possible 3-ring heterocycles and the thirteen possible 4-ring heterocycles were tested for mutagenic activity in the histidine reversion (Ames assay) system. One of the 3-ring isomers, naphtho(1,2-b)-thiophene, and six of the 4-ring isomers induced mutations in Salmonella test strains. One of these compounds, phenanthro(3,4-b)thiophene, displayed approximately the same mutagenic activity as benzo(a)pyrene. A two-step adsorption chromatographic procedure was developed in order to fractionate synthetic fuels into various chemical-type classes for studying the relative concentrations and mutagenic activities of the various types. An SRC-II Heavy Distillate was fractionated into aliphatic hydrocarbons, polycyclic aromatic hydrocarbons, sulfur heterocycles, indoles and carbazoles, azaarenes, and amino polycyclic aromatic hydrocarbons. It was found that the amino-PAH fraction contained most of the mutagenic activity. A survey was made for compounds containing both nitrogen and sulfur heteroatoms in their structures. A number of these compounds were detected by GC using nitrogen- and sulfur-selective detection.

  7. ITER technology R and D progress report. Report by the Director. ITER technical advisory committee meeting, 25-27 June 2000, St. Petersburg

    International Nuclear Information System (INIS)

    2001-01-01

    The overall philosophy for the ITER design has been to use established approaches through detailed analysis and to validate their application to ITER through technology R and D, including fabrication of full scale or scalable models of key components. All this R and D work has been done for ITER under collaboration among the Home Teams, with a total resource of about 660 KIUA. R and D issues for ITER-FEAT are almost the same as for the 1998 ITER design. Major developments and fabrication have been completed and tests have significantly progressed. The technical output from the R and D validates the technologies and confirms the manufacturing techniques and quality assurance incorporated in the ITER design, and supports the manufacturing cost estimates for important key cost drivers. The testing of models is continuing to demonstrate their performance margin and/or to optimize their operational use. Their realisation offers insights useful for a possible future collaborative construction activity. Valuable and relevant experience has already been gained in the management of industrial scale, cross-party ventures. The successful progress of these projects increases confidence in the possibility of jointly constructing ITER in an international project framework. The R and D present status is summarized in the following: details are given in Chapters 2 and 3. Significant efforts and resources have been devoted to the Seven Large R and D Projects which cover all the major key components of the basic machine of ITER and their maintenance tools

  8. Humic substances in performance assessment of nuclear waste disposal: Actinide and iodine migration in the far-field. First technical progress report

    International Nuclear Information System (INIS)

    Buckau, G.

    2003-04-01

    The present project is one in a series of research activities supported by the European Commission on the role of humic substances for the long-term safety of nuclear waste disposal. These activities started in the mid eighties within the MIRAGE project (MIgration of RAdionuclides in the GEosphere) with the most recent project being ''Effects of humic substances on the migration of radionuclides: Complexation and transport of actinides (HUMICS)'' (FI4W-CT96-0028). The HUMICS project was conducted within the fourths framework of the European Commissions research program. It started January 1997 and had a duration of three years. The results of the HUMICS project can be found in three open technical progress reports and a final report [1-4]. In analogy with the HUMICS project, the present project makes use of annual technical progress reports where individual results are published as papers in the form of annexes. By this approach, results rapidly become available to interested parties in a compact form before their publication in various scientific journals and conference proceedings. Furthermore, some of the more preliminary and/or detailed results are not likely to appear in scientific journals and proceedings. The present project is conducted within the fifths framework of the European Commissions research program. It started November 2001 and has a duration of three years. The present report covers the first project year, i.e. November 2001 to September 2002. The project is divided into eight different work packages. These are (i) ''Critical assessment of experimental methods'', (ii) ''Generation and characterization of humic substances'', (iii) ''Radionuclide humate interaction data by designed system investigations'', (iv) ''Characterization of radionuclide humate complexes'', (v) ''Natural chemical analogue studies'', (vi) ''Radionuclide transport experiments'', (vii) ''Model development'', and (viii) ''Performance assessment''. Division of work into

  9. Continuous Fiber Wound Ceramic Composite (CFCC) for Commercial Water Reactor Fuel. Technical progress report for period ending April 1, 2000

    International Nuclear Information System (INIS)

    2000-01-01

    Our program began on August 1, 1999. As of April 1, 2000, the progress has been in materials selection and test planning. Three subcontracts are in place (McDermott Technologies Inc. for continuous fiber reinforced ceramic tubing fabrication, Swales Aerospace for LOCA testing of tubes, and Massachusetts Institute of Technology for In Reactor testing of tubes). With regard to materials selection we visited McDermott Technologies Inc. a number of times, including on February 23, 2000 to discuss the Draft Material Selection and Fabrication Report. The changes discussed at this meeting were implemented and the final version of this report is attached (attachment 1). McDermott Technologies Inc. will produce one type of tubing: Alumina oxide (Nextel 610) fiber, a carbon coating (left in place), and alumina-yttria matrix. A potentially desirable CFCC material of silicon carbide fiber with spinel matrix was discussed. That material selection was not adopted primarily due to material availability and cost. Gamma Engineering is exploring the available tube coatings at Northwestern University as a mechanism for reducing the permeability of the tubes, and thus, will use coating as a differentiating factor in the testing of tubing in the LOCA test as well as the In-Reactor Test. The conclusion of the Material Selection and Fabrication Report lists the possible coatings under evaluation. With regard to Test Planning, the MIT and Swales Aerospace have submitted draft Test Plans. MIT is attempting to accommodate an increased number of test specimens by evaluating alternative test configurations. Swales Aerospace held a design review at their facilities on February 24, 2000 and various engineering alternatives and safety issues were addressed. The final Test Plans are not expected until just before testing begins to allow for incorporation of changes during ''dry runs.''

  10. Fission track analysis of Pu in small specimens of biological material: Technical progress report, August 1, 1987--July 31, 1988

    International Nuclear Information System (INIS)

    Wrenn, M.E.

    1988-01-01

    The objective of this research is to develop a highly specific and ultrasensitive method capable of detecting 100 aCi/liter of 239 Pu in human urine. The method using neutron induced fission track analysis is to be made free of interference from uranium, the only naturally occurring element with an isotope which fissions with thermal neutrons. A simplified flow diagram for the method is shown in Figure 1. Briefly 239 Pu is coprecipitated quantitatively from urine with rhodozonic acid. The precipitate containing the 239 Pu is dissolved in HCl and is sequentially passed through two ion exchange columns and reduced in volume. The element is then deposited in a circular area on a thick polycarbonate detector and a thinner detector is placed over the circular deposit. The plastic detectors are then irradiated to a high thermal neutron fluence in a research reactor. The detectors are etched in a caustic solution for controlled times and temperatures in order to develop the fission tracks. Images of tracks are formed both on the thin and thick plastic detectors. Total tracks in the thinner detector are measured with a locally developed spark counter and in the thick plastic are measured by counting with a microscope. The results will be made quantitative by constructing a calibration curve for 239 Pu. 3 refs., 9 figs., 3 tabs

  11. Investigation of lithium thionyl chloride battery safety hazards. Quarterly technical progress report 29 Sep-31 Dec 81

    Energy Technology Data Exchange (ETDEWEB)

    McDonald, R.C.

    1981-12-31

    Glass Li/SOCl2 cells have been designed and built which will be used to discharge and overdischarge flat electrodes in sufficient but not excess electrolyte. The cells will be used for generation of electrolyte samples for chemical spectroscopy and overdischarged cathodes for morphological studies. A metal cell has been designed and built for overdischarge of flat electrodes. E.S.R., Raman, FTIR, and UV/VIS fluorescence spectra have been taken of electrolyte at various stages of discharge and overdischarge. Two chemical species detectable with ESR are generated on discharge. The first resonance found also in electrolyte solutions saturated with sulfur, develops uniformly through discharge. The second as yet unidentified species becomes evident towards the second half of discharge increasing species becomes evident towards the second half of discharge increasing in concentration faster than sulfur. Following removal from the cell, the second species disappears as visible fluorescence increases in intensity the sulfur related peak remains. Raman and FTIR spectra show a profusion of emission and absorption peaks respectively. Analysis of this data is still in process. Preliminary optical studies of overdischarged cathode studies in cathode limited cells show that lithium dendrites do grow on the surface of carbon.

  12. Investigation of lithium thionyl chloride battery safety hazards. Quarterly technical progress report 1 Jan-31 Mar 82

    Energy Technology Data Exchange (ETDEWEB)

    McDonald, R.C.

    1982-03-31

    Scanning electron and optical microscopic investigation of an overdischarged cathode from a cathode limited Li/SOCl2 cell reveal a three-dimensional reticulated lithium dendrite structure. Individual dendrites do not grow and longer than about 50 microns or any thicker than about 4 microns in diameter before branching at random angles. E.S.R. spectra of 50% and 100% overdischarged anode limited cells reveal a third chemical species carrying an unpaired electron which is distinct from the two radical species observed during discharge. No significant difference is observed between the Raman spectra of 100% discharged electrolyte and 50% cathode limited overdischarged electrolyte. The same holds true for infrared spectra. The Raman spectra of 90% anode limited overdischarged electrolyte shows most of the peaks occuring at 100% discharge in addition to 687, 727, 819, and 854 per cm. The infrared spectrum of the same solution shows most the the features occuring at 100% discharge in addition to the reduction of 981 cm-1 and growth of peaks at 1397,1085,1070 (shoulder) 661 and 602 cm-1. Peaks at 1070 and 661 always occur weakly in discharged electrolyte spectra and are quite strong in the spectrum of Li/sub 2/S0/sub 4/ saturated electrolyte.

  13. Endoscopic and keyhole endoscope-assisted neurosurgical approaches: a qualitative survey on technical challenges and technological solutions.

    Science.gov (United States)

    Marcus, Hani J; Cundy, Thomas P; Hughes-Hallett, Archie; Yang, Guang-Zhong; Darzi, Ara; Nandi, Dipankar

    2014-10-01

    The literature reflects a resurgence of interest in endoscopic and keyhole endoscope-assisted neurosurgical approaches as alternatives to conventional microsurgical approaches in carefully selected cases. The aim of this study was to assess the technical challenges of neuroendoscopy, and the scope for technological innovations to overcome these barriers. All full members of the Society of British Neurosurgeons (SBNS) were electronically invited to participate in an online survey. The open-ended structured survey asked three questions; firstly, whether the surgeon presently utilises or has experience with endoscopic or endoscope-assisted approaches; secondly, what they consider to be the major technical barriers to adopting such approaches; and thirdly, what technological advances they foresee improving safety and efficacy in the field. Responses were subjected to a qualitative research method of multi-rater emergent theme analysis. Three clear themes emerged: 1) surgical approach and better integration with image-guidance systems (20%), 2) intra-operative visualisation and improvements in neuroendoscopy (49%), and 3) surgical manipulation and improvements in instruments (74%). The analysis of responses to our open-ended survey revealed that although opinion was varied three major themes could be identified. Emerging technological advances such as augmented reality, high-definition stereo-endoscopy, and robotic joint-wristed instruments may help overcome the technical difficulties associated with neuroendoscopic approaches. Results of this qualitative survey provide consensus amongst the technology end-user community such that unambiguous goals and priorities may be defined. Systems integrating these advances could improve the safety and efficacy of endoscopic and endoscope-assisted neurosurgical approaches.

  14. Hepatic Iron Quantification on 3 Tesla (3 T Magnetic Resonance (MR: Technical Challenges and Solutions

    Directory of Open Access Journals (Sweden)

    Muhammad Anwar

    2013-01-01

    Full Text Available MR has become a reliable and noninvasive method of hepatic iron quantification. Currently, most of the hepatic iron quantification is performed on 1.5 T MR, and the biopsy measurements have been paired with R2 and R2* values for 1.5 T MR. As the use of 3 T MR scanners is steadily increasing in clinical practice, it has become important to evaluate the practicality of calculating iron burden at 3 T MR. Hepatic iron quantification on 3 T MR requires a better understanding of the process and more stringent technical considerations. The purpose of this work is to focus on the technical challenges in establishing a relationship between T2* values at 1.5 T MR and 3 T MR for hepatic iron concentration (HIC and to develop an appropriately optimized MR protocol for the evaluation of T2* values in the liver at 3 T magnetic field strength. We studied 22 sickle cell patients using multiecho fast gradient-echo sequence (MFGRE 3 T MR and compared the results with serum ferritin and liver biopsy results. Our study showed that the quantification of hepatic iron on 3 T MRI in sickle cell disease patients correlates well with clinical blood test results and biopsy results. 3 T MR liver iron quantification based on MFGRE can be used for hepatic iron quantification in transfused patients.

  15. Exploring technological and architectural solutions for nursing home residents, care professionals and technical staff: Focus groups with professional stakeholders.

    NARCIS (Netherlands)

    M.H. Wetzels; H.T.G. Weffers; A.M.C. Dooremalen; Joost van Hoof; Eveline Wouters

    2014-01-01

    Buildings with innovative technologies and architectural solutions are needed as a means of support for future nursing homes alongside adequate care services. This study investigated how various groups of stakeholders from healthcare and technology envision the nursing home of the future in the

  16. Enhancement of organizational and technical solutions regarding anchoring of completed construction facilities of underground railway system to operating control

    Directory of Open Access Journals (Sweden)

    Е. Г. Козин

    2017-12-01

    Full Text Available Stages of practical realization of measures prescribed by requirements documents regarding anchoring of capital structures of underground railway system to operating control are considered in the article. On the basis of algorithm structure analysis, which includes obtaining a permit for putting into operation and cadastre works execution a range of solutions was proposed concerning optimization of construction project owner and operating organization activities with the purpose of terms reduction of capital structures handover to operation. The results of work of a commission responsible for completed underground railway system objects acceptance and putting into operation were analyzed. Considering example of object «Second entrance hall area of «Sportivnaya» station the statistical data of revealed snagging items is consolidated and dynamics of corrective actions is provided.Proposed solutions laid the foundation for corrections of requirements documents and were accepted for realization in the process of works acceptance of Saint-Petersburg underground railway system objects.

  17. On progress of the solution of the stationary 2-dimensional neutron diffusion equation: a polynomial approximation method with error analysis

    International Nuclear Information System (INIS)

    Ceolin, C.; Schramm, M.; Bodmann, B.E.J.; Vilhena, M.T.

    2015-01-01

    Recently the stationary neutron diffusion equation in heterogeneous rectangular geometry was solved by the expansion of the scalar fluxes in polynomials in terms of the spatial variables (x; y), considering the two-group energy model. The focus of the present discussion consists in the study of an error analysis of the aforementioned solution. More specifically we show how the spatial subdomain segmentation is related to the degree of the polynomial and the Lipschitz constant. This relation allows to solve the 2-D neutron diffusion problem for second degree polynomials in each subdomain. This solution is exact at the knots where the Lipschitz cone is centered. Moreover, the solution has an analytical representation in each subdomain with supremum and infimum functions that shows the convergence of the solution. We illustrate the analysis with a selection of numerical case studies. (author)

  18. On progress of the solution of the stationary 2-dimensional neutron diffusion equation: a polynomial approximation method with error analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ceolin, C., E-mail: celina.ceolin@gmail.com [Universidade Federal de Santa Maria (UFSM), Frederico Westphalen, RS (Brazil). Centro de Educacao Superior Norte; Schramm, M.; Bodmann, B.E.J.; Vilhena, M.T., E-mail: celina.ceolin@gmail.com [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica

    2015-07-01

    Recently the stationary neutron diffusion equation in heterogeneous rectangular geometry was solved by the expansion of the scalar fluxes in polynomials in terms of the spatial variables (x; y), considering the two-group energy model. The focus of the present discussion consists in the study of an error analysis of the aforementioned solution. More specifically we show how the spatial subdomain segmentation is related to the degree of the polynomial and the Lipschitz constant. This relation allows to solve the 2-D neutron diffusion problem for second degree polynomials in each subdomain. This solution is exact at the knots where the Lipschitz cone is centered. Moreover, the solution has an analytical representation in each subdomain with supremum and infimum functions that shows the convergence of the solution. We illustrate the analysis with a selection of numerical case studies. (author)

  19. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Monday 9 February 2004 From 10:00 to 12:00 - IT Auditorium - bldg. 31, 3rd floor ANSOFT High-Frequency Seminar David Prestaux, Application Engineer, ANSOFT F-78535 BUC, France This Technical Training seminar will present two Ansoft application products: Ansoft HFSS and Ansoft Designer. Ansoft HFSS makes use of the Finite Element Method (FEM) to calculate field solutions from first principles. It can accurately predict all high-frequency behaviours such as dispersion, mode conversion, and losses due to materials and radiation. Ansoft Designer is a suite of design tools to fully integrate high-frequency, physics-based electromagnetic simulations into a seamless system-level simulation environment. Ansoft Designer uses a simple interface to give complete control over every design task, by a method allowing multiple solvers, Solver on Demand. • Introduction • Overview of the Ansoft Total solution • Ansoft HFSS 9...

  20. Mesonic atoms. Technical progress report

    International Nuclear Information System (INIS)

    Kunselman, R.

    1981-01-01

    Research on mesic atoms during 1981 is reported. This includes measurement of x-rays from pionic hydrogen and pionic deuterium; muonic K, L, and M x-ray spectra of mercury 199 and mercury 201; and pionic chromium 54, scandium 45, vanadium 51, manganese 55, and iron

  1. 1986 PAEC Technical progress report

    International Nuclear Information System (INIS)

    1987-01-01

    Presented are on-going research and development projects of the Philippine Atomic Energy Commission in the fields of agriculture and natural resources, health and nutrition, supportive research, nuclear applications services, industry and energy, and other scientific and technological services and information system. (ELC)

  2. Exotic atoms. Technical progress report

    International Nuclear Information System (INIS)

    Kunselman, R.

    1994-01-01

    The experiments use a variety of hydrogen isotopic mixtures to form solid targets for muons to produce muonic hydrogen isotope atoms that escape into vacuum. The method relies on transfer of the muon from a proton to either a deuteron or a triton. The resulting muonic deuterium or muonic tritium will not immediately thermalize because of the very low elastic cross sections (RT effect), and are emitted from the surface of the layer. A second solid hydrogen isotopic target is produced downstream on which the muonic hydrogen atom can react. Measurements which detect decay electrons, muonic x-rays, and fusion products have been used to study the processes of energy dependence of transfer, production rates, and muon molecular formation. The processes include muon catalyzed fusion of muonic tritium with deuterium which is the most possible candidate for energy production fusion. Our interest is the nuclear physics reaction rates and to use the muonic hydrogen isotopes in vacuum for energy level measurements. The method uses time of flight and is reminiscent of double scattering experiments. Two other experiments are in the development stages. First to measure the energy dependence of the Ramsauer-Townsend cross section in tritium where it has not been measured. The measurements would be compared to deuterium and calculations. Second, kaonic atoms, hypernuclei, and kaon-nucleon scattering at DAPHNE

  3. Proposing a Technical Solution for Restoring Longitudinal Connectivity in the Brădeni/Retiş Accumulation Area on Hârtibaciu River

    Directory of Open Access Journals (Sweden)

    Voicu Răzvan

    2016-04-01

    Full Text Available The fish fauna of the Hârtibaciu River has experienced a disrupted connectivity due to the hydrotechnical works and the Brădeni/Retiş Dam located across the Hârtibaciu watercourse being one of this significant obstacles. The newly proposed constructed wetlands can improve the habitat quality for the fish species of conservative interest sampled in the Brădeni/Retiş Dam proximity Rhodeus amarus, and can increase the individuals’ number of this population. Also can benefit the local populations of Phoxinus phoxinus and Gobio obtusirostris. Using gravitational force and also the underground layout, a proposed technical solution gives maximum safety regarding the water supply for the newly proposed to be created wetlands.

  4. Method and Result of Experiment for Support of Technical Solutions in the Field of Perfection of a Nuclear Fuel Cycle for Future PWR Reactors

    International Nuclear Information System (INIS)

    Ostrovskiy, V.; Kudryavtsev, E.; Tutnov, I.

    2011-01-01

    The paper presents the basics of approach of planning and carrying out of experiments to validate safety PWR reactors of the future when accepting technical solutions concerning using of improved fuel rods in fuel assembly. Basic principles and criteria used for the validation of technical solutions and developments in improving of nuclear fuel cycle of PWR reactors of the future are presented from the point of safety of future operation of modified fuel rods. We explore the questions of safety operation of PWR reactors with fuel assemblies, containing fuel rods with different length of fuel. The paper discusses the ways of solving of important tasks of critical facility experiments conducting for verification of new technical solutions in the sphere of PWR nuclear fuel cycle improvement on the base of international standards ISO 2000:9000 and functional safety recommendations of IEC (International Electromechanical Commission). New Federal laws of Russian Federation define the main principle for demands to NPP and any supplier of nuclear techniques. The principle is 'quantity indicators of risk should not exceed comprehensible social size of the established indicators of safety for any moment of operation of NPP'. On the other hand the second principle should be applied to extraction of the greatest benefit from operation of the equipment, systems or the NPP as whole: 'The long operation and full commercial use of resource and service properties of the equipment, systems and the NPP as a whole'. Realization of this principle assumes development and introduction of new technical solutions for a validation of guarantees of safety of the future operation of NPP or it separate components. Solving the practical problems of a validation of safety use of fuel rods with the increased length of a fuel column in fuel assembly in nuclear reactors of the future, we should choose new strategies and programs of verification experiments on the base of the analysis of guarantees

  5. Technical note: Analysis of claims and disputes in contracts for oil and gas development projects in Iran with solutions

    Directory of Open Access Journals (Sweden)

    Fathollah Sajedi

    2017-08-01

    Full Text Available Contracts for oil and gas development projects are naturally complex, they are explained with some of maps and technical specifications. To supply the goals of contracts, it is necessary to construct by a team having owner, consulting engineer and contractor. The unique aspects of each project and team working are resulting to disagreements. It should be noted that the majority of team workers have not previously worked together. It may not be expected to forecast all project aspects in design and preparation of tender documents process. However, in some cases it will occur inconsistencies in contract documents and possibly may be disagreements on commentary of the cases which there are in the provisions of the contract. Every root of disagreement resulted in to claim and finally dispute. Lack of foresight and/or existing ambiguous texts in some provisions of contract, not being aware of components of the project to conditions and obligations and rules of contract will complex and sometimes impossible the agreement on implementation problems. Therefore, the claims will be resulted in disputes and inflict financial losses to contractors and/or owners and then the projects will not be completed. In Iran many activities have not been carried out about claims and disputes in different orientations especially in areas futures and hence, it was studied in this research. Firstly, research history was considered and the causes of claims and disputes were identified in process of different levels of oil projects construction from primary to exploitation and then a questionnaire was prepared using the comments of experts. Finally, the questionnaire was analysed by SPSS and the approved factors in creation of claims and disputes and in their roots were ranked.

  6. Pile composting of two-phase centrifuged olive husk residues: technical solutions and quality of cured compost.

    Science.gov (United States)

    Alfano, G; Belli, C; Lustrato, G; Ranalli, G

    2008-07-01

    The present work proposed an economically sustainable solution for composting olive humid husks (OHH) and leaves (OL) at a small/medium sized olive oil mill. We planned and set up a composting plant, the prototype taking the form of a simplified low-cost turning machine, and evaluated the use of an inoculum of one year-old composted humid husks (CHH) and sheep manure (SM) to facilitate the starting phase of the process. Trials were carried out using four piles under different experimental conditions (turnover, static, and type of inoculum). The best results were achieved with turnover and an inoculum that induced fast start-up and a correct evolution of the composting process. The final product was a hygienically clean, cured compost.

  7. Ocoxin oral solution? as a complement to irinotecan chemotherapy in the metastatic progression of colorectal cancer to the liver

    OpenAIRE

    Hernandez-Unzueta, Iera; Benedicto, Aitor; Olaso, Elvira; Sanz, Eduardo; Viera, Cristina; Arteta, Beatriz; M?rquez, Joana

    2017-01-01

    Colorectal cancer (CRC) is an aggressive disease in which patients usually die due to its metastatic progression to the liver. Up to date, irinotecan is one of the most used chemotherapeutic agents to treat CRC metastasis with demonstrated efficacy. However, the severity of the side effects constitute the main limitation to its use in the treatment. Consequently, new complementary therapies are being developed to avoid these adverse effects while maintaining the efficacy of the antitumoral dr...

  8. Progress in the domain of emissions tracking and environment radioactivity monitoring - Proceedings of the technical days organised by the SFRP Environment Section

    International Nuclear Information System (INIS)

    Calmet, Dominique; Calvez, Marianne; Rivasseau, Corinne Cea; Monfort, Marguerite; Manificat, Guillaume; Pierrard, Olivier; Couvez, Celine; Masson, Olivier; Bruno, Valerie; Renaud, Philippe; Genova, Zhana; Reynal, Nathalie; Le Coz, Eric; Tchilian, Nathalie; Diana, Jean-Jacques; Beguinel, Philippe; Cortes, Pierre; Puydarrieux, Stephane; Brun, Thierry; Devin, Patrick; Clavel, Benoit; Hemidy, Pierre-Yves; Gontier, Gilles; Delloye, Thierry; Mailliat, Alain; Ferreri, Giovanni; LECLERC, Elisabeth

    2015-11-01

    The Environment Section of the French Society of Radiation Protection (SFRP) organized a technical meeting on the progress made in the domain of emissions tracking and environment radioactivity monitoring. This document brings together the abstracts and the presentations (slides) of the different talks given at the meeting: 1 - Environment monitoring at the global, national and local scale: historical overview (Dominique CALMET, CEA); 2 - Evolution of radioactivity monitoring in the environment from 1960 to the present day (Guillaume MANIFICAT, IRSN); 3 - Euratom's legal framework (Zhana GENOVA, CTE); 4 - Main regulatory changes during the last decade (Nathalie REYNAL, ASN); 5 - Progress of standardization works on radioactive effluent emissions control and environment monitoring (Philippe BEGUINEL, BNEN); 6 - From operators' self-monitoring to ASN's inspections: a many components control system (Eric LE COZ, ASN); 7 - Control of effluents and emissions management at CEA Centres (Marianne CALVEZ, CEA); 8 - Liquid and gaseous effluents of ITER experimental facility: description and impacts (Pierre CORTES, IO); 9 - Effluents and emissions management strategy at AREVA NC La Hague facility (Stephane PUYDARRIEUX, AREVA); 10 - Radioactive effluents from nuclear facilities ongoing deconstruction: from dimensioning to real effluents (Benoit CLAVEL, EDF); 11 - Radionuclides decontamination process for liquid effluents using micro-algae at the laboratory scale (Corinne RIVASSEAU, CEA); 12 - Radioactive effluents from nuclear medicine services: management, monitoring and impact measurement methods (Nathalie TCHILIAN, ASN); 13 - Evolution history of effluents management and environment monitoring at the Solvay La Rochelle site (Thierry DELLOYE, SOLVAY); 14 - Different international approaches in effluents management and monitoring: example of French and German gaseous effluents - regulation, analyses, accounting rules (Jean-Jacques DIANA, ASN); 15 - Environment

  9. Isotope effects in the solution of gases in liquids. Progress report, November 1, 1979-October 31, 1980

    International Nuclear Information System (INIS)

    Benson, B.B.; Krause, D. Jr.

    1980-09-01

    Research under this contract provides strong evidence for the existence of structure in liquid water. Application of a simple zero-point-energy argument to our data for the isotopic fractionation of nonpolar gases during aqueous solution shows that a dissolved gas molecule may be considered to occupy a cavity with a size characteristic of water and independent of the size of the solute molecule. For a cubical cavity model for water, the length of a side of the cube would be approximately 6.3 A at 0 0 C, while a spherical cavity model would have a dia of 6.8 A. The isotopic measurements in addition may lead to a more consistent set of diameters for the solute molecules. Precise new measurements show that the isotopic fractionation of nitrogen during solution is only slightly smaller than that for oxygen, despite the fact that the difference between the reciprocal masses of the 28 to 29 pair is only one-half the difference for the 32 to 34 pair. The cavity model provides a simple quantitative explanation for this result. Measurements on the polar molecules 12 C 16 O, 13 C 16 O, and 12 C 18 O do not fit the simple model, because of the asymmetrical distributions of their masses. This leads to a correlation between rotational and translational degrees of freedom, which affects the energies of the ground states of these heteronuclear molecules as they oscillate within the cavity

  10. Comparison of Changes in Central Corneal Thickness During Corneal Collagen Cross-Linking, Using Isotonic Riboflavin Solutions With and Without Dextran, in the Treatment of Progressive Keratoconus.

    Science.gov (United States)

    Zaheer, Naima; Khan, Wajid Ali; Khan, Shama; Khan, M Abdul Moqeet

    2018-03-01

    To compare intraoperative changes in central corneal thickness (CCT) during corneal cross-linking, using 2 different isotonic riboflavin solutions either with dextran or with hydroxy propyl methylcellulose, in the treatment of progressive keratoconus. In this retrospective study, we analyzed records of corneal thickness measurements, taken during various steps of cross-linking. Cross-linking was performed using either isotonic riboflavin with dextran (group A) or isotonic riboflavin with hydroxy propyl methylcellulose (without dextran) (group B). CCT measurements were recorded before and after epithelial removal, after saturation with respective isotonic riboflavin solution, after use of hypotonic riboflavin in selected cases, and after ultraviolet A (UV-A) application. A mixed-way analysis of variance was conducted on CCT readings within each group and between both groups, and p dextran causes a significant decrease in corneal thickness, whereas dextran-free isotonic riboflavin causes a significant increase in corneal thickness, thus facilitating the procedure.

  11. Tanks Focus Area FY98 midyear technical review

    Energy Technology Data Exchange (ETDEWEB)

    Schlahta, S.N.; Brouns, T.M.

    1998-06-01

    The Tanks Focus Area (TFA) serves as the DOE`s Office of Environmental Management`s national technology and solution development program for radioactive waste tank remediation. Its technical scope covers the major functions that comprise a complete tank remediation system: waste retrieval, waste pretreatment, waste immobilization, tank closure, and characterization of both the waste and tank with safety integrated into all the functions. In total, 17 technologies and technical solutions were selected for review. The purpose of each review was to understand the state of development of each technology selected for review and to identify issues to be resolved before the technology or technical solution progressed to the next level of maturity. The reviewers provided detailed technical and programmatic recommendations and comments. The disposition of these recommendations and comments and their impact on the program is documented in this report.

  12. Tanks Focus Area FY98 midyear technical review

    International Nuclear Information System (INIS)

    Schlahta, S.N.; Brouns, T.M.

    1998-06-01

    The Tanks Focus Area (TFA) serves as the DOE's Office of Environmental Management's national technology and solution development program for radioactive waste tank remediation. Its technical scope covers the major functions that comprise a complete tank remediation system: waste retrieval, waste pretreatment, waste immobilization, tank closure, and characterization of both the waste and tank with safety integrated into all the functions. In total, 17 technologies and technical solutions were selected for review. The purpose of each review was to understand the state of development of each technology selected for review and to identify issues to be resolved before the technology or technical solution progressed to the next level of maturity. The reviewers provided detailed technical and programmatic recommendations and comments. The disposition of these recommendations and comments and their impact on the program is documented in this report

  13. Modern technical and technological solutions of radiation control to combat illicit trafficking of nuclear and radioactive materials across borders

    International Nuclear Information System (INIS)

    Frymire, A.; Kagan, L.; Stavrov, A.

    2006-01-01

    an integral part of the common task to be solved. It is very important that after the radioactive source has been detected such procedures as saving, transferring and analyzing of the information should be successfully completed. This requires performing the independent remote control of the status of a portal monitor, technical and methodological support and monitoring of personnel actions. This part of the task can be solved by creating the specialized automated system. The portal monitors and the RAVEN (Radiation Alarm and Video Event Notification) system developed and manufactured by the company TSA Systems Ltd is one and the most successful and efficient examples of how this task can be accomplished. RAVEN was designed to both capture and view data and video images relating to a radiological detection incident. Stored sets of data and video can be used in the rapid identification of the method of transportation of radioactive substances. Quick review of the incident can be made by using the on screen controls that allow the user to step through each image and pause whenever necessary. This allows the user to relay any identifying information to response personnel in the field for possible secondary inspection or other interdiction. Local Alarm Stations (LAS) can be configured to only display information that will be useful to the local user. The Central Alarm Station (CAS) can be configured to display much more detailed information that is useful for alarm trending and other data analysis. Multiple LAS or CAS locations can easily be established and through the use of wireless routers these locations can be mobile. Multi-layered password protection will restrict unauthorized access to sensitive data or video and will protect the privacy of innocent individuals. Graphs of detection levels along with the ability to view which individual detector is displaying the most activity will allow the user to better understand where in a large container the radioactive

  14. Materials testing and requirements for the ERDA nuclear-powered artificial heart. Technical progress report, July 15, 1974--May 1, 1975

    International Nuclear Information System (INIS)

    Andrade, J.D.; Coleman, D.L.; Leigh, A.; Hufferd, W.L.

    1975-01-01

    Progress on the materials research and development effort for the ERDA-sponsored nuclear-powered artificial heart program is presented. Progress made during the first three years on hydrogel grafting and biological studies is summarized. Progress during the fourth year on studies of implanted artificial hearts, development of albumin surfaces, and in vitro mechanical studies is presented. (U.S.)

  15. Ultracoatings: Enabling Energy and Power Solutions in High Contact Stress Environments through next-generation Nanocoatings Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Clifton B. Higdon III

    2012-03-20

    A review of current commercially available, industrial-grade, low friction coatings will show that interfacial contact pressures nearing 1GPa ({approx}150ksi) inherently limit surface engineering solutions like WC, TiN, TiAlN, and so forth. Extremely hard coatings, then, are often pursued as the principle path, although they too are not without significant limitations. A majority of these compounds are inherently brittle in nature or may not pair well with their mating substrate. In either case, their durability in high contact stress environments is compromised. In parallel to thin film coatings, many conventional surface treatments do not yield an interface hard enough to withstand extreme stresses under load. New research into advanced, nanocomposite materials like (Ti, Zr)B2 shows great promise. Bulk compacts of this compound have demonstrated an order of magnitude better wear resistance than current offerings, notably materials like tungsten carbide. At a laboratory level, the (Ti,Zr)B2 nanocomposite material exhibited abrasive and erosive wear resistance nearly ten times better than existing mixed-phase boride systems. In ASTM abrasion and erosion testing, these new compositions exhibit wear resistance superior to other known advanced materials such as RocTec 500 and 'Borazon' cubic boron nitride. Many significant challenges exist for mass production of (Ti, Zr)B2, one of which is the necessary processing technology that is capable of minimizing deleterious impurity phases. Secondly, this material's performance is derived from a synergistic effect of the two materials existing as a single phase structure. While the individual constituents of TiB2 and ZrB2 do yield improvements to wear resistance, their singular effects are not as significant. Lastly, deposition of this material on a commercial level requires thorough knowledge of nanocomposite boride solids; the benefits associated with these innovative new materials are just being realized

  16. Design of a multipurpose “zero energy consumption” building according to European Directive 2010/31/EU: Architectural and technical plants solutions

    International Nuclear Information System (INIS)

    Desideri, Umberto; Arcioni, Livia; Leonardi, Daniela; Cesaretti, Luca; Perugini, Perla; Agabitini, Elena; Evangelisti, Nicola

    2013-01-01

    Considering the significant impact that the residential sector has on energy consumption, it is particularly important to implement policies aimed at improving energy efficiency in buildings. Highly energy efficient buildings can either save primary energy or disseminate the use of the most suitable technologies to be used in new constructions. Due to those reasons, the Municipality of Città della Pieve promoted the creation of a “Renewable Energy Park” in a deprived area of its territory, where some green technologies could be installed and tested. This site has also been considered as an optimal location for an educational/demonstrative “zero energy consumption” building for multifunctional activities and realized with the most innovative techniques to save energy. The building may be considered as an example to study and optimize the benefits of higher energy efficiency together with the use of renewable energy systems. In this paper the technical solutions adopted both in the building envelope and the technical plants are described and discussed. A simulation of the behaviour of the building in summer and winter was carried out in order to assess the benefits that can be obtained both in energetic and economic terms. - Highlights: • Project focused on the implementation of European Directive 2010/31/EU. • Energy efficiency in buildings for saving primary energy using renewable sources. • Dissemination of the concept of sustainable development for new buildings. • High performance construction layers and high efficiency plants. • Design of a “zero energy consumption” building with zero emissions of CO 2

  17. Experimental determination of contaminant metal mobility as a function of temperature, time and solution chemistry. 1997 annual progress report

    International Nuclear Information System (INIS)

    Bruton, C.; Carroll, S.; O'Day, P.; Sahai, N.

    1997-01-01

    'Strontium is significantly more mobile than other hazardous radioactive metals. Its partitioning between aqueous and solid phases is controlled by reactions that occur at the interface between natural waters and minerals. At a groundwater site in Hanford (200-BP-5), the aerial extent of the 90 Sr plume is 100 times larger than the aerial extent of the 137 Cs and the 239 Pu plumes. Similarly, contaminated, perched watertables at INEL have much higher aqueous concentrations of 90 Sr than 137 Cs, presumably because Cs is preferentially sorbed to solids (Duncan 1995). Under high physical flow conditions, such as those in the highly fractured rock at Hanford and INEL, 90 Sr present in plumes may spread off-site and cause contamination of aquifers or other water sources. Geochemical factors that may contribute to the overall mobility of Sr in natural waters are the solubilities of phases such as strontianite (SrCO 3 ) and formation of strong complexes with sulfate and nitrate. Although 90 Sr is mobilized in natural waters in these examples, significant concentrations may also be present in solid phases. Sorption experiments using a wide variety of substrates at room temperature have shown that Sr is removed from solution under certain conditions. Additionally, strontianite (SrCO 3 ) may precipitate at low Sr concentrations in the pH range of waters in contact with basaltic rocks, which varies between pH 8 and 10. Waters contain variable amounts of carbonate owing to atmospheric interactions; the partial pressure of CO 2 is about 10 x 3.5 atm in air and commonly as high as 10 x 2.5 atm in soils. The objective of this work is to determine the fundamental data needed to predict the behavior of strontium at temperature and time scales appropriate to thermal remediation. The authors approach combines macroscopic sorption/precipitation and desorption/dissolution kinetic experiments, which track changes in solution composition, with direct molecular characterization of

  18. Missouri local technical assistance program at Missouri University of Science and Technology (formerly University of Missouri--Rolla) : annual progress report January-December 2007.

    Science.gov (United States)

    2009-02-01

    This annual report is a summary of the activities during 2007 for the Missouri Local Technical Assistance Program (Missouri LTAP), which is located at Missouri University of Science and Technology. The report highlights Missouri LTAPs performance ...

  19. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Tuesday 3 February 2004 From 09:00 to 13:30 - Training Centre Auditorium - bldg. 593, room 11 USB (Universal Serial Bus) CYPRESS Seminar Claudia Colombini, Field Application Engineer CYPRESS ActiveComp Electronic GmbH D-85077 MANCHING, Germany As a pioneer in USB, CYPRESS sets the standard for cost-effective solutions without sacrificing functionality, performance or reliability. Having shipped over 200 million USB devices, Cypress is the undisputed market leader and demonstrates unmatched USB expertise. With the industry's broadest selection of USB solutions, Cypress has the right silicon, software and support for every USB application, from Low-speed to High-Speed and USB On-The-Go (OTG). 9:00 - 10:30 Overview of USB systems. USB CYPRESS product overview. Peripherals: Low Speed, Full Speed, High Speed (1.1 and 2.0). Hub Solutions, Embedded Host Solutions, On-The-Go (OTG) and wireless USB. USB Development Tools (first part) 10:30 -...

  20. Progressive geometric algorithms

    NARCIS (Netherlands)

    Alewijnse, S.P.A.; Bagautdinov, T.M.; de Berg, M.T.; Bouts, Q.W.; ten Brink, Alex P.; Buchin, K.A.; Westenberg, M.A.

    2015-01-01

    Progressive algorithms are algorithms that, on the way to computing a complete solution to the problem at hand, output intermediate solutions that approximate the complete solution increasingly well. We present a framework for analyzing such algorithms, and develop efficient progressive algorithms

  1. Progressive geometric algorithms

    NARCIS (Netherlands)

    Alewijnse, S.P.A.; Bagautdinov, T.M.; Berg, de M.T.; Bouts, Q.W.; Brink, ten A.P.; Buchin, K.; Westenberg, M.A.

    2014-01-01

    Progressive algorithms are algorithms that, on the way to computing a complete solution to the problem at hand, output intermediate solutions that approximate the complete solution increasingly well. We present a framework for analyzing such algorithms, and develop efficient progressive algorithms

  2. Heat treatment as a universal technical solution for silcrete use? A comparison between silcrete from the Western Cape (South Africa and the Kalahari (Botswana.

    Directory of Open Access Journals (Sweden)

    Patrick Schmidt

    Full Text Available Heat treatment was one of the first transformative technologies in the southern African Middle Stone Age (MSA, with many studies in the Cape coastal zone of South Africa identifying it as an essential step in the preparation of silcrete prior to its use in stone tool manufacture. To date, however, no studies have investigated whether heat treatment is necessary for all silcrete types, and how geographically widespread heat treatment was in the subcontinent. The aim of this study is to investigate experimentally whether heat treatment continued further north into the Kalahari Desert of Botswana and northernmost South Africa, the closest area with major silcrete outcrops to the Cape. For this we analyse the thermal transformations of silcrete from both regions, proposing a comprehensive model of the chemical, crystallographic and 'water'-related processes taking place upon heat treatment. For the first time, we also explore the mobility of minor and trace elements during heat treatment and introduce a previously undescribed mechanism-steam leaching-causing depletion of a limited number of elements. The results of this comparative study reveal the Cape and Kalahari silcrete to respond fundamentally differently to heat treatment. While the former can be significantly improved by heat, the latter is deteriorated in terms of knapping quality. These findings have important implications for our understanding of the role of fire as a technical solution in MSA stone tool knapping, and for the extension of its use in southern Africa. Silcrete heat treatment-at least in the form we understand it today-may have been a strictly regional phenomenon, confined to a narrow zone along the west and south coast of the Cape. On the basis of our findings, silcrete heat treatment should not be added as a new trait on the list of behaviours that characterise the MSA of the southern African subcontinent.

  3. The development of coal-based technologies for Department of Defense facilities. Volume 2, Appendices. Semiannual technical progress report, September 28, 1994--March 27, 1995

    International Nuclear Information System (INIS)

    Miller, B.G.; Bartley, D.A.; Hatcher, P.

    1996-01-01

    This semiannual progress report contains the following appendices: description of the 1,000 lb steam/h watertube research boiler; the Pennsylvania CGE model; Phase II, subtask 3.9 coal market analysis; the CGE model; and sector definition

  4. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball and W. Zeuner

    2011-01-01

    In this report we will review the main achievements of the Technical Stop and the progress of several centrally-managed projects to support CMS operation and maintenance and prepare the way for upgrades. Overview of the extended Technical Stop  The principal objectives of the extended Technical Stop affecting the detector itself were the installation of the TOTEM T1 telescopes on both ends, the readjustment of the alignment link-disk in YE-2, the replacement of the light-guide sleeves for all PMs of both HFs, and some repairs on TOTEM T2 and CASTOR. The most significant tasks were, however, concentrated on the supporting infrastructure. A detailed line-by-line leak search was performed in the C6F14 cooling system of the Tracker, followed by the installation of variable-frequency drives on the pump motors of the SS1 and SS2 tracker cooling plants to reduce pressure transients during start-up. In the electrical system, larger harmonic filters were installed in ...

  5. Productivity Measurement Of Technical Institute

    Directory of Open Access Journals (Sweden)

    Miss.Pooja Yadav

    2015-05-01

    Full Text Available Abstract The increasing concern over globalization between other things has made the achievement of lifetime skills vital for all classes of people. Achievement of such skills can be developed from technical education programs in the advance of any nation. Skill gaining provides knowledge and inculcates the approaches that are essential for arrival and progress into an occupation. When skills are developed in any occupation it will provide and improve the standard of living with the cover beside poverty thereby behind national development. This paper observes sampling distribution and moving average concept that how technical education can generate the required skills the significance of skill acquisition its roles benefits and sustainability in national development. It also mentions among others that government should look into and improve productivity that can encourage skill achievement for the youths. The solutions are divided the sampling box into few group before stacking up workstation and use table and some other wood product. Cost reduction for each solution was intended and the solution with highest cost decrease is chosen to increase the productivity of the college.

  6. Progress in automation, robotics and measuring techniques

    CERN Document Server

    Zieliński, Cezary; Kaliczyńska, Małgorzata

    2015-01-01

    This book presents recent progresses in control, automation, robotics, and measuring techniques. It includes contributions of top experts in the fields, focused on both theory and industrial practice. The particular chapters present a deep analysis of a specific technical problem which is in general followed by a numerical analysis and simulation, and results of an implementation for the solution of a real world problem. The presented theoretical results, practical solutions and guidelines will be useful for both researchers working in the area of engineering sciences and for practitioners solving industrial problems.    .

  7. social & technical innovations

    International Development Research Centre (IDRC) Digital Library (Canada)

    CHANGE: GAPS BRIDGED BY SMART SOLUTIONS. CHALLENGE: INABILITY TO REACH THOSE IN NEED. SOLAR PANELS. OVERCOME POWER. SUPPLY CHALLENGES. IN BURKINA FASO. SOCIAL & TECHNICAL. INNOVATIONS. BANGLADESH BURKINA FASO ETHIOPIA KENYA LEBANON PERU VIETNAM.

  8. Research and development of methods/utilities and rules for managing cooperation for performance improvement in government offices. Second Technical progress report, September 1, 1992--January 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Kurstedt, H.A.

    1993-03-01

    Purpose is to help managers approach their responsibilities proactively, so that they can anticipate problems and take actions to alleviate or eliminate those problems. Continuous performance improvement, the philosophy behind total quality management, requires working cooperatively to do a little better each day. The most effective tools are working through a closed set of 9 methods: setting expectations, charting, defining indicators and standards, collecting and logging data, converting data to information, organizing and presenting information, reviewing status and progress, self-management, and appraising. In addition, there are 8 rules: focus on what you can do, supply physical evidence of progress, pay attention to detail, inspect (don`t expect), review progress routinely and frequently, face ``success/fail`` squarely, communicate crisply, and conduct honest, open appraisals. Scope and plans of the draft research plan (study areas) are described.

  9. Progress in resolving open design issues from the ODR. Report by the Director. ITER technical advisory committee meeting, 25-27 June 2000, St. Petersburg

    International Nuclear Information System (INIS)

    2000-01-01

    This report presents progress in resolving open design issues from the ITER-FEAT Outline Design Report and is not repeating the ODR information but concentrates on the specific issues and the progress towards their resolution. It includes some aspects of the Physics analysis (inductive operation scenario and sensitivity analysis, ion heating, possibility of high Q and ignition operation, divertor physics), Magnets (TF coil loads, inductive flux generation, conductor design issues), Vessel/in Vessel (manifolding of blanket coolant, vacuum vessel design development, design implications of divertor material choice), Buildings and Plant services, Operation and Safety

  10. Attitudes towards technical progress. Acceptance of technology in national and international comparison. Einstellungen zum technischen Fortschritt. Technikakzeptanz im nationalen und internationalen Vergleich

    Energy Technology Data Exchange (ETDEWEB)

    Jaufmann, D.; Kistler, E. (Internationales Inst. fuer Empirische Sozialoekonomie (INIFES), Gemeinnuetzige GmbH, Leitershofen (Germany)) (eds.)

    1991-01-01

    Engineering, new technologies, science and attitudes of the public are important determinants for influencing the development and the state of a country. Problems concerning the acceptance of technical projects and developments also can be the scapegoat for other, deeper conflicts in society - they are important, and increasingly a social and political challenge. The book supplies empirically fundamental and interdisciplinary prerequisites for future debates. The contributions were presented at a public seminar in January 1989. (orig./HSCH).

  11. Progress report for '89

    International Nuclear Information System (INIS)

    Podest, M.

    1990-08-01

    The 1989 Progress Report presents the most important scientific and technical achievements of the Nuclear Research Institute's research work. Some specialized products prepared at or fabricated by the NRI are mentioned as well. (author). 24 figs., 8 tabs., 101 refs

  12. [Conduct theoretical and experimental research programs in high energy physics]: Technical progress, Appendix A-2, FTP/A, Item 20,f

    International Nuclear Information System (INIS)

    1986-01-01

    Progress is reported in these areas: neutrino physics; nucleon decay and the intrinsic properties of neutrinos; the D-zero experiment; QCD jet physics and ultrarelativistic nuclear physics; the Colliding Detector at Fermilab; rare kaon decay; the Anomalous Single Photon detector at SLAC; particle theory; neutrino astrophysics and cosmology; and operations and support services

  13. Materials testing and requirement for the ERDA nuclear-powered artificial heart. Technical progress report, July 15, 1975--May 30, 1976. [BIOMER and AVCOTHANE

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, J. D.; Hufferd, W. L.; Lyman, D. J.

    1976-01-01

    The two materials currently being used for the artificial heart fabrication are BIOMER and AVCOTHANE. BIOMER is a polyether urethane polymer. AVCOTHANE is a proprietary polyurethane/polydimethylsiloxane polymer blend. Research progress on the chemical degradation, mechanical strength, and blood compatibility is reported. (TFD)

  14. A "Fear" Studies Perspective and Critique: Analyzing English and Stengel's Progressive Study of Fear and Learning in "Education Theory." Technical Paper No. 37

    Science.gov (United States)

    Fisher, R. Michael

    2011-01-01

    The author critiques the progressive approach of two contemporary educational philosophers (English and Stengel) on the topic of fear and learning. Using a postmodern integral approach, this article examines the tendency of reductionism, individualism, and psychologism as part of a hegemonic liberalism and modernism in discourses on fear and…

  15. GPHS-RTGs in support of the Cassini Mission. Semi-annual technical progress report, April 3, 1995--October 1, 1995

    International Nuclear Information System (INIS)

    1995-01-01

    This document is the April-October 1995 Progress Report on the Cassini RTG Program. Nine tasks are summarized; (1) Spacecraft integration and liason, (2) Engineering support, (3) Safety, (4) Unicouple fabrication, (5) ETG fabrication, assembly, and test, (6) Ground support equipment, (7) RTG shipping and launch support, (8) Design, reviews, and mission applications, and (9) Project management, QA, contract changes, and material acquisitions

  16. Materials testing and requirement for the ERDA nuclear-powered artificial heart. Technical progress report, July 15, 1975--May 30, 1976

    International Nuclear Information System (INIS)

    Andrade, J.D.; Hufferd, W.L.; Lyman, D.J.

    1976-01-01

    The two materials currently being used for the artificial heart fabrication are BIOMER and AVCOTHANE. BIOMER is a polyether urethane polymer. AVCOTHANE is a proprietary polyurethane/polydimethylsiloxane polymer blend. Research progress on the chemical degradation, mechanical strength, and blood compatibility is reported

  17. Bioremediation of mixed microbial mats: System development of mixed contaminants for application at the Savannah River Site. Annual technical progress report, October 1, 1995--September 30, 1996

    International Nuclear Information System (INIS)

    Bender, J.; Phillips, P.

    1996-01-01

    The fundamental objective of this project is to develop and field test the mixed microbial mat bioremediation system for decontamination of target sites at SRS. Although microbial mats have performed well in several pilot projects in the past, atypical problems and site characteristics at SRS demand special field designs. In the interest of designing a pilot and locating it at an appropriate site, the project investigators have worked closely with the technical staff at the SREL. We have concluded that the diverse characteristics of contaminations at SRS may dictate testing several pilot designs during the course of this project

  18. Evaluation and capacity building to improve precollege science and mathematics achievement in the US: 10 CFR, Part 605. Technical progress report, June--December 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-12-31

    The National Center for Improving Science Education has undertaken activities to achieve evaluation goals for DOE`s Precollege programs: develop means to determine program quality; develop means for determining the contribution of DOE precollege programs to both teacher enhancement and student achievement; provide evaluation designs and instruments and reports of program quality and impact; and strengthen both DOE`s and the Labs` capacity to do both short- and long-term planning as well as deliver effective programs and evaluation. Appendices include evaluation/technical assistance report, profiling teacher research participation and teacher development programs, teacher surveys, impact assessment design, and teacher research participation programs anecdotes for 8 labs.

  19. Non-technical constraints to eradication: the Italian experience.

    Science.gov (United States)

    Moda, Giuliana

    2006-02-25

    Although technical constraints to eradication of bovine tuberculosis are well-recognised, non-technical constraints can also delay progress towards eradication, leading to inefficiency and increased programme costs. This paper seeks to analyse the main non-technical constraints that can interfere with the successful implementation of tuberculosis eradication plans, based on experiences from an area of high tuberculosis prevalence in Regione Piemonte, Italy. The main social and economic constraints faced in the past 20 years are reviewed, including a social reluctance to recognise the importance of seeking eradication as the goal of disease control, effective communication of technical issues, the training and the organization of veterinary services, the relationship between the regional authority and farmers and their representatives, and data management and epidemiological reporting. The paper analyses and discusses the solutions that were applied in Regione Piemonte and the benefits that were obtained. Tuberculosis eradication plans are one of the most difficult tasks of the Veterinary Animal Health Services, and non-technical constraints must be considered when progress towards eradication is less than expected. Organizational and managerial resources can help to overcome social or economic obstacles, provided the veterinary profession is willing to address technical, but also non-technical, constraints to eradication.

  20. Critical experiments supporting underwater storage of tightly packed configurations of spent fuel pins. Technical progress report, January 1-March 31, 1981

    International Nuclear Information System (INIS)

    Hoovler, G.S.; Baldwin, M.N.

    1981-04-01

    Critical experiments are in progress on arrays of 2 1/2% enriched UO 2 fuel pins simulating underwater pin storage of spent power reactor fuel. Pin storage refers to a spent fuel storage concept in which the fuel assemblies are dismantled and the fuel pins are tightly packed into specially designed canisters. These experiments are providing benchmark data with which to validate nuclear codes used to design spent fuel pin storage racks

  1. Search for neutrino oscillations and measurements of neutrino-nucleus cross sections. Technical progress report, 16 January 1985-15 October 1985

    International Nuclear Information System (INIS)

    Koetke, D.D.

    1985-01-01

    Progress is reported in these areas: work done at LANL on experiment E764, including beam line modification, new target installation, system testing, on-line software development, beam tuning, and data acquisition; neutrino Monte Carlo program development; flux calculations for the DC modified torroidal pion focussing device for the low energy decay-in-flight neutrino source; and prototype preparation for a large modular segmented detector

  2. GPHS-RTGs in support of the Cassini Mission. Semi annual technical progress report, 28 March 1994--25 September 1994

    International Nuclear Information System (INIS)

    1994-01-01

    The progress on the radioisotope generators and ancillary activities is described. This report is organized by program task as follows: spacecraft integration and liaison; engineering support; safety; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; design, reviews, and mission applications; project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; contractor acquired government owned property (CAGO) acquisition

  3. TECHNICAL COORDINATION

    CERN Multimedia

    Austin Ball

    Summary of progress since last CMS week. Ten years of construction work have been completed. CMS is closed, in very close to the ideal low luminosity configuration, and performed well in the first tests with LHC beam. Behind this encouraging news is the story of a summer of intense commitment by many teams (from the collaboration and 3 CERN departments) working together, against the clock and despite many minor setbacks, to ensure that the experiment was ready to play a leading role in the excitement of September 10. Following beampipe bakeout and refill with pure neon, a magnificent effort by the ECAL group and the pt 5 technical crew made it possible to install and commission all 4 ECAL endcap Dees before the end of August. In the shadow of this activity, the barrel and forward pixel trackers and part of the beam monitoring were installed within the vac tank. The pt 5 technical teams then succeeded in safely removing the 20t installation tables and their support blocks from beneath the already installed ...

  4. Atmospheric pollution and heating plants in urban area. What technical solutions for the coal and the heavy oil? For which costs?; Pollution atmospherique et chaufferies en milieu urbain. Quelles solutions techniques pour le charbon et le fioul lourd?. A quel couts?

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    In France, furnaces fed with coal and heavy fuel and established in urban area, are bound by many restraints: a reinforcement of the regulations on atmospheric emissions, a strong social demand bound to the urban air quality improvement and a necessary costs mastership. So buildings managers and persons responsible for district heating are confronted with technical and strategical choices. To answer their questions ADEME organized a day of information around four main themes: the urban heating in France, actions on fuels, possible technics for the smokes desulfurization and nitrogen oxides reduction, costs and financing of the solutions. (A.L.B.)

  5. TECHNICAL COORDINATION

    CERN Multimedia

    Austin Ball

    2013-01-01

      Since the last report, much visible progress has been made, as the LS1 programme approaches the halfway point. From early October, technical and safety shift-crew have been present around the clock, allowing detectors to stay switched on overnight, ensuring that safety systems are operational and instructions for non-expert shift-crew are clear. LS1 progress Throughout the summer, whilst the solenoid vacuum tank and YB0 surfaces were accessible, an extensive installation programme took place to prepare for Tracker colder operation and the PLT installation, in 2014, the Phase 1 Pixel Tracker installation, in 2016–’17, and the HCAL Phase 1 upgrade completion, ending in LS2. This included pipework for N2 or dry air to flush the Tracker bulkhead region, many sensors to monitor temperature and dew point in the Tracker and its service channels, heating wires outside the Tracker cooling bundles, supports for the new vacuum-jacketed, concentric, CO2 Pixel cooling lines, the PLT cool...

  6. Progress in design, research and development and testing of safety systems for advanced water cooled reactors. Proceedings of a technical committee meeting

    International Nuclear Information System (INIS)

    1996-04-01

    The meeting covered the following topics: Developments in design of safety-related heat removal components and systems for advanced water cooled reactors; status of test programmes on heat removal components and systems of new designs; range of validity and extrapolation of test results for the qualification of design/licensing computer models and codes for advanced water cooled reactors; future needs and trends in testing of safety systems for advanced water cooled reactors. Tests of heat removal safety systems have been conducted by various groups supporting the design, testing and certification of advanced water cooled reactors. The Technical Committee concluded that the reported test results generally confirm the predicted performance features of the advanced designs. Refs, figs, tabs

  7. Progress in design, research and development and testing of safety systems for advanced water cooled reactors. Proceedings of a technical committee meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-04-01

    The meeting covered the following topics: Developments in design of safety-related heat removal components and systems for advanced water cooled reactors; status of test programmes on heat removal components and systems of new designs; range of validity and extrapolation of test results for the qualification of design/licensing computer models and codes for advanced water cooled reactors; future needs and trends in testing of safety systems for advanced water cooled reactors. Tests of heat removal safety systems have been conducted by various groups supporting the design, testing and certification of advanced water cooled reactors. The Technical Committee concluded that the reported test results generally confirm the predicted performance features of the advanced designs. Refs, figs, tabs.

  8. A methodology for the analysis and selection of alternatives for the disposition of surplus plutonium. Quarterly technical progress report, April 1, 1995--June 30, 1995

    International Nuclear Information System (INIS)

    Mulder, R.

    1995-01-01

    The Office of Fissile Materials Disposition is currently involved in the development of a comprehensive approach to the long-term storage and disposition of fissile materials. A major objective of this effort is to provide a framework for US efforts to prevent the proliferation of nuclear weapons. This will entail both the elimination of excess highly enriched uranium and plutonium, and the insurance of the highest standards of safety, security, and international accountability. The Office of Fissile Materials Disposition is supporting an Interagency Working Group that has initiated a comprehensive review of alternatives for plutonium disposition which takes into account non-proliferation, economic, technical, institutional, schedule, environmental, and health and safety issues. These alternatives were identified by the development of screening criteria as a guide to the selection of alternatives that best achieve the fissile nuclear material long-term storage and disposition goals of the US Government

  9. 1993 Annual progress report for subsidiary agreement No. 2 (1991--1996) between AECL and US/DOE for a radioactive waste management technical co-operative program

    International Nuclear Information System (INIS)

    1993-01-01

    A coordinated research program on radioactive waste disposal is being carried out by the Atomic Energy of Canada Limited and the US Department of Energy. This annual report describes progress in the following eight studies: Fundamental materials investigations; In-situ stress determination; Development of a spent fuel dissolution model; Large block tracer test--Experimental testing of retardation models; Laboratory and field tests of in-situ hydrochemical tools; Cigar Lake--Analogue study, actinide and fission product geochemistry; Performance assessment technology exchange; and Development of multiple-well hydraulic test and field tracer test methods

  10. 1993 Annual progress report for subsidiary agreement No. 2 (1991--1996) between AECL and US/DOE for a radioactive waste management technical co-operative program

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    A coordinated research program on radioactive waste disposal is being carried out by the Atomic Energy of Canada Limited and the US Department of Energy. This annual report describes progress in the following eight studies: Fundamental materials investigations; In-situ stress determination; Development of a spent fuel dissolution model; Large block tracer test--Experimental testing of retardation models; Laboratory and field tests of in-situ hydrochemical tools; Cigar Lake--Analogue study, actinide and fission product geochemistry; Performance assessment technology exchange; and Development of multiple-well hydraulic test and field tracer test methods.

  11. Evaluation of using cyclocranes to support drilling & production of oil & gas in wetland areas. Sixth quarterly technical progress report, incorporating milestone schedule/status, October 1993--December 1993

    Energy Technology Data Exchange (ETDEWEB)

    Eggington, W.J.

    1994-04-01

    This report is a progress report on a planned program falling under wetlands area research related to drilling, production, and transportation of oil and gas resources. Specifically the planned program addresses an evaluation of using cyclocraft to transport drill rigs, mud, pipes and other materials and equipment in a cost effective and environmentally safe manner to support oil and gas drilling and production operations in wetland areas. During this period, task 5, subscale tests, and task 7, environmental impacts, were completed. Work was continued on task 10, technology transfer, and the preparation of the final report as part of task 11.

  12. Silicon germanium (SiGe) radioisotope thermoelectric generator (RTG) program for space missions. Nineteenth technical progress report, December 1980-January 1981

    International Nuclear Information System (INIS)

    1981-01-01

    Work accomplished during the reporting period on the DOE Silicon Germanium RTG Program, Contract DE-AC01-79ET-32043 is described. This program consists of the following three tasks: multi-hundred watt RTG for the Galileo probe mission; reestablishment of silicon germanium unicouple capability; and general purpose heat source RTG for the international solar polar and Galileo orbiter missions. Details of program progress for each task, including a milestone schedule and a discussion of current problem areas (if any) are presented

  13. METHOD IMPROVEMENT FOR DETERMINING THE TECHNICAL LEVEL OF CIVIL AIRCRAFT

    Directory of Open Access Journals (Sweden)

    2016-01-01

    Full Text Available Aircraft are high-tech engineering products which are characterized by a wide range of properties including the two most important groups that respectively characterize the efficiency and technical level.Improving the aircraft efficiency is an essential factor for air transport development, but the efficiency can not be fully describe the technical system, especially in forecasting and new technology requirements development. Aircraft de- signer must evaluate the prospects of a technical solution, but it’s not always possible to calculate the efficiency accuratelyat the design stage. The operator should be able to choose the most technically-advanced aircraft available in the market inorder not to let it grow obsolete quickly. This determines the need for non-economic evaluation of technical systems that can be done by assessment of their technical level.The technical level is a general index that includes a set of technical perfection indicators. Technical perfection is reflected in terms of material and energy intensity, in terms of ergonomics, safety, etc. and is achieved as a result of origi- nal design solutions, the use of new high-strength low-density materials, the introduction of advanced technological pro-cesses, calculation methods, verification, testing, etc.There is a tight connection between the product properties and its weight, because weight is the material reflection of these properties. Therefore, improvement of the product properties usually leads to an intense increase of its weight. To deal with this phenomenon is only possible with widely using scientific and technical progress results. In accordance with this, the technical perfection can be interpreted as a major component of quality that is created without the weight increase. This approach requires investment in research and testing new technical solutions.The method was developed to determine the technical level of civil long-haul aircraft which has been modified to

  14. Technical presentation

    CERN Multimedia

    GS Department

    2010-01-01

    10 March 2010 DYNEOS 10:00 – 12:00 - Main Building, Room B, 61-1-009 Dyneos AG is active in the fields of photonics, laser and high-precision positioning. Our highly qualified engineer team has more than 30 years of experience in electro-optical solutions sales. The engineers are supported by a technical and administrative team. We are focused on the Swiss market and represent six suppliers (Coherent, PI Physik Instrumente, SIOS, Nanonics Imaging, APE, Ekspla) in order to give a qualified sales and service support to our customers. Our products are dedicated to the research field as well as to industry. In addition to standard catalog products, we offer custom designs to fulfill the specific needs of OEM customers or specific applications.

  15. A Fast Solution of the Lindley Equations for the M-Group Regression Problem. Technical Report 78-3, October 1977 through May 1978.

    Science.gov (United States)

    Molenaar, Ivo W.

    The technical problems involved in obtaining Bayesian model estimates for the regression parameters in m similar groups are studied. The available computer programs, BPREP (BASIC), and BAYREG, both written in FORTRAN, require an amount of computer processing that does not encourage regular use. These programs are analyzed so that the performance…

  16. Progress report no. 76

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    8 papers from the Institute of Hydrodynamics and Hydraulic Engineering of the Technical University of Denmark cover the problems of sedimentation, boundary currents, solute transport, advection-dispersion etc. Mathematical models of hydraulic problems are presented. (EG)

  17. Geological repositories: The last nuclear frontier. International Conference on Geological Repositories: Political and Technical Progress, 8-10 December 2003, Stockholm, Sweden

    International Nuclear Information System (INIS)

    ElBaradei, M.

    2003-01-01

    Few issues play so central a role in the public acceptance of nuclear technologies as the management and disposal of spent fuel and radioactive waste. In the current climate, geological repositories have come to be viewed not as one option among many for completing the nuclear fuel cycle, but as the only sustainable solution achievable in the near term. But despite a longstanding agreement among experts that geological disposal can be safe, technologically feasible and environmentally sound, a large part of the general public remains skeptical. This statement deals with the challenges that IAEA is facing to build public confidence related to spent fuel repositories

  18. Sequential purification and crystal growth for the production of low cost silicon substrates. Quarterly technical progress report No. 1, 15 September 1979-31 December 1979

    Energy Technology Data Exchange (ETDEWEB)

    Liaw, M.; Secco, F.; Ingle, B.; Down, D.

    1980-02-01

    Over the past several years, Motorola's Materials Technology Laboratory (MTL), has been conducting several projects with goals directed at the production of high quality low cost silicon crystals. One of the projects which is being investigated is the direct purification of MG-Si. A unique characteristic of the approach used by this project is the use of a crystal puller to perform both purification and crystal growth. Sequential steps of purification were taken. By the completion of this series of purification, the purified MG-Si melt will be further purified by impurity redistribution using ingot pulling. The final purified silicon will be in an ingot form of desired dimensions for slicing into silicon sheets. The sequential steps of purification include: (1) leaching of MG-Si charge, (2) phase separation, (3) reactive gas treatment, (4) liquid-liquid extraction (called Slagging), and (5) purification by redistribution of impurities using ingot pulling. Progress on items (1) and (2) is reported. (WHK)

  19. Identification and validation of heavy metal and radionuclide hyperaccumulating terrestrial plant species, Quarterly technical progress report, December 20, 1995--March 20, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Kochian, L.; Brady, D.; Last, M.; Ebbs, S.

    1995-12-01

    Although the period covered by this progress report began on December 20, 1994, which was the date that DOE approved the Interagency Agreement, the agreement was not approved by USDA until January 9, 1995 and the first scientists working on the project were not hired until February 1, 1995. The first goal of the research supported by the Interagency Agreement is to use hydroponic techniques to identify plant species and genotypes with potential for heavy metal hyperaccumulation for planting on a test site at Silverbow Creek and for radionuclide ({sup 90}Sr and {sup 137}Cs) accumulation on a test site at INEL, Idaho, later this year. The second goal of this research is to identify soil amendment procedures that will enhance the bioavailability of heavy metals and radionuclides in the soil without increasing the movement of the contaminants of concern (COC`s) into the groundwater. Our initial research covered in this report focuses on the first goal.

  20. Development of a thermionic magnicon amplifier at 11.4 GHz. Technical progress report, 16 May 1994--31 December 1995

    International Nuclear Information System (INIS)

    Gold, S.H.; Fliflet, A.W.; Manheimer, W.M.

    1995-01-01

    This is a progress report on a four-year research program entitled 'Development of a Thermionic Magnicon Amplifier at 11.4 GHz', which is under way in the Plasma Physics Division of the Naval Research Laboratory (NRL) under Interagency Agreement DE-AI02-94ER40681. This report covers the period 16 May 1994 through 31 December 1995. The magnicon is an advanced microwave tube with potential application to future high gradient linear accelerators such as TeV colliders. Under this program, NRL plans to build and test a thermionic magnicon amplifier tube powered by a 500 kV, 200 A, 10 Hz modulator with a 1 μsec pulse. However, the experiments that were carried out during the period covered by this report were driven by a single-shot Marx generator, and the electron beam was produced from a graphite plasma cathode

  1. Geothermal space/water heating for Mammoth Lakes Village, California. Quarterly technical progress report, 13 December 1976-12 March 1977

    Energy Technology Data Exchange (ETDEWEB)

    Sims, A.V.; Racine, W.C.

    1977-01-01

    During the second three months of this feasibility study to determine the technical, economic and environmental feasibility of heating Mammoth Lakes Village, California using geothermal energy, the following work was accomplished. A saturation survey of the number and types of space and water heaters currently in use in the Village was completed. Electric energy and ambient temperature metering equipment was installed. Peak heating demand for Mammoth Lakes was estimated for the years 1985, 1990 and 2000. Buildings were selected which are considered typical of Mammoth Lakes in terms of their heating systems to be used in estimating the cost of installing hydronic heating systems in Mammoth. Block diagrams and an order of magnitude cost comparison were prepared for high-temperature and low-temperature geothermal district heating systems. Models depicting a geothermal district heating system and a geothermal-electric power plant were designed, built and delivered to ERDA in Washington. Local input to the feasibility study was obtained from representatives of the State of California Departments of Transportation and Fish and Game, US Forest Service, and Mono County Planning Department.

  2. Implementing waste minimization at an active plutonium processing facility: Successes and progress at technical area (TA) -55 of the Los Alamos National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Balkey, J.J.; Robinson, M.A.; Boak, J.

    1997-12-01

    The Los Alamos National Laboratory has ongoing national security missions that necessitate increased plutonium processing. The bulk of this activity occurs at Technical Area -55 (TA-55), the nations only operable plutonium facility. TA-55 has developed and demonstrated a number of technologies that significantly minimize waste generation in plutonium processing (supercritical CO{sub 2}, Mg(OH){sub 2} precipitation, supercritical H{sub 2}O oxidation, WAND), disposition of excess fissile materials (hydride-dehydride, electrolytic decontamination), disposition of historical waste inventories (salt distillation), and Decontamination & Decommissioning (D&D) of closed nuclear facilities (electrolytic decontamination). Furthermore, TA-55 is in the process of developing additional waste minimization technologies (molten salt oxidation, nitric acid recycle, americium extraction) that will significantly reduce ongoing waste generation rates and allow volume reduction of existing waste streams. Cost savings from reduction in waste volumes to be managed and disposed far exceed development and deployment costs in every case. Waste minimization is also important because it reduces occupational exposure to ionizing radiation, risks of transportation accidents, and transfer of burdens from current nuclear operations to future generations.

  3. Simultaneous high-temperature removal of alkali and particulates in a pressurized gasification system. Final technical progress report, April 1981-July 1983

    Energy Technology Data Exchange (ETDEWEB)

    Mulik, P.R.; Alvin, M.A.; Bachovchin, D.M.

    1983-09-01

    This program is directed at performing experimental and analytical investigations, deriving system designs, and estimating costs to ascertain the feasibility of using aluminosilicate-based getters for controlling alkali in pressurized gasification systems. Its overall objective is to develop a plan for evaluating a scaled-up version of the gettering process as a unit operation or as an integral part of a particulate removal device. This report describes work completed on the four technical program tasks: Thermodynamic projections; Getter Selection and Qualification; System Performance Projections; and Program Definition for Concept Scale-up during the 27-month contract performance period. Work completed on the thermodynamic projections includes a data base update, development of alkali phase diagrams, and system performance projections. Getter selection and qualification efforts involved over 70 kinetic studies in which a leading candidate getter - emathlite - was selected and characterized. System performance projections identified a packed-bed configuration containing relatively large getter pellets as the preferred contacting device for a full-scale unit. For emathlite, we concluded that full-scale unit bed heights of 2 m or less would be required if we assume annual replacement on the basis of bed saturation capacity. Concept scale-up work involved defining the hardware and test program requirements for further development of the emathlite packed-bed system. 56 references, 80 figures, 74 tables.

  4. Implementing waste minimization at an active plutonium processing facility: Successes and progress at technical area (TA) -55 of the Los Alamos National Laboratory

    International Nuclear Information System (INIS)

    Balkey, J.J.; Robinson, M.A.; Boak, J.

    1997-01-01

    The Los Alamos National Laboratory has ongoing national security missions that necessitate increased plutonium processing. The bulk of this activity occurs at Technical Area -55 (TA-55), the nations only operable plutonium facility. TA-55 has developed and demonstrated a number of technologies that significantly minimize waste generation in plutonium processing (supercritical CO 2 , Mg(OH) 2 precipitation, supercritical H 2 O oxidation, WAND), disposition of excess fissile materials (hydride-dehydride, electrolytic decontamination), disposition of historical waste inventories (salt distillation), and Decontamination ampersand Decommissioning (D ampersand D) of closed nuclear facilities (electrolytic decontamination). Furthermore, TA-55 is in the process of developing additional waste minimization technologies (molten salt oxidation, nitric acid recycle, americium extraction) that will significantly reduce ongoing waste generation rates and allow volume reduction of existing waste streams. Cost savings from reduction in waste volumes to be managed and disposed far exceed development and deployment costs in every case. Waste minimization is also important because it reduces occupational exposure to ionizing radiation, risks of transportation accidents, and transfer of burdens from current nuclear operations to future generations

  5. Undergraduate technical skills training guided by student tutors – Analysis of tutors' attitudes, tutees' acceptance and learning progress in an innovative teaching model

    Science.gov (United States)

    Weyrich, Peter; Schrauth, Markus; Kraus, Bernd; Habermehl, Daniel; Netzhammer, Nicolai; Zipfel, Stephan; Jünger, Jana; Riessen, Reimer; Nikendei, Christoph

    2008-01-01

    Background Skills labs provide a sheltered learning environment. As close supervision and individual feedback were proven to be important in ensuring effective skills training, we implemented a cross-year peer tutor system in our skills lab of internal medicine that allowed intense training sessions with small learning groups (3–4 students) taught by one student tutor. Methods The expectations, experiences and criticisms of peer tutors regarding the tutor system for undergraduate skills lab training were investigated in the context of a focus group. In addition, tutees' acceptance of this learning model and of their student tutors was evaluated by means of a pre/post web-based survey. Results 14 voluntary senior students were intensely prepared by consultants for their peer tutor activity. 127 students participated in the project, 66.9% of which responded to the web-based survey (23 topics with help of 6-point Likert scale + free comments). Acceptance was very high (5.69 ± 0.07, mean ± SEM), and self-confidence ratings increased significantly after the intervention for each of the trained skills (average 1.96 ± 0.08, all p skills training to be provided by faculty staff only. Focus group analyses with tutors revealed 18 different topics, including profit in personal knowledge and personal satisfaction through teaching activities. The ratio of 1:4 tutor/tutees was regarded to be very beneficial for effective feedback, and the personalized online evaluation by tutees to be a strong motivator and helpful for further improvements. The tutors ascribed great importance to the continuous availability of a contact doctor in case of uncertainties. Conclusion This study demonstrates that peer teaching in undergraduate technical clinical skills training is feasible and widely accepted among tutees, provided that the tutors receive sufficient training and supervision. PMID:18400106

  6. Computational modeling and experimental studies on NO{sub x} reduction under pulverized coal combustion conditions. Third quarterly technical progress report, July 1, 1995--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Kumpaty, S.K.; Subramanian, K.

    1995-12-31

    An experimental plan outlining the first year`s activity was sent to Dr. Lori Gould, Project Officer/Contracting Officer`s Technical Representative on April 24, 1995. An approval was received with some questions on June 15, 1995. However, with some foresight of the director of the in-house combustion group of the PETC, Dr. Ekmann, a tentative hold-off on the purchase of the equipment was requested by the project officer on June 29, 1995. Enclosed with that request were some of Dr. Ekmann`s concerns. The research team spent the month of July in study of pertinent literature as well as in the preparation of the responses to Dr. Gould`s comments and Dr. Ekmann`s concerns. These responses included the choice of the reactor, reactor design, rate of gas heating, detailed test matrix and answers to host of other comments. Upon review of the above information submitted on July 24, 1995 by the Rust research team, the project officer called for a conference call on September 6, 1995 which involved the PI (Dr. Kumpaty), the research consultant (Mr. Subramanian), Dr. Gould and Dr. Ekmann. Dr. Ekmann insisted that further calculations be made on the rate of gas heating without taking radiation into account. Accordingly, calculations pertaining to the rate of gas heating based on convection were performed and submitted to Dr. Ekmann on September 13, 1995. This report contains the information emerged through the dialogue between the Rust College research team and the PETC represented by Dr. Gould and Dr. Ekmann during this quarter.

  7. Plutonium, cesium and uranium series radionuclides in the Hudson River estuary and other environments. Annual technical progress report, 1 December 1980-30 November 1981

    International Nuclear Information System (INIS)

    Simpson, H.J.; Trier, R.M.

    1981-01-01

    Radionuclide activities were measured in sediment cores and suspended particle samples throughout the salinity range of the Hudson River estuary. Activities of 137 Cs, 134 Cs, 60 Co, 239 240 Pu, and 238 Pu indicate reasonably rapid accumulation rates in the sediments of marginal cove areas, and very rapid deposition in the harbor region adjacent to New York City, resulting in 239 240 Pu accumulations there more than an order of magnitude greater than the fallout delivery rate. Fallout 239 240 Pu reaching the Hudson is almost completely retained within the systems by particle deposition, while 80 to 90% of the 137 Cs derived from both reactor releases and fallout is exported to the coastal waters in solution. Depth profiles of radionuclides in Hudson sediments are not significantly altered by physical mixing processes in the sediments in areas accumulating particles at greater than 1 cm/yr. Measurements of fallout 239 2 xperimental quantities

  8. Direct assays of radiation-induced DNA base lesions in mammalian cells: Technical progress report, July 1, 1986--December 1, 1988

    International Nuclear Information System (INIS)

    Wheeler, K.T. Jr.

    1988-01-01

    Our cesium irradiator was installed in April 1987 and has the capability of irradiating DNA solutions, cells and animals at dose rates from >60 Gy/min to <10/sup /minus/2/ Gy/min. By early summer all of the dosimetry and set-ups were established to perform this research. In may 1987, Dr. Krystyna Lesiak left to return to the National Institutes of Health. However, she has remained a collaborator over the past 1/1/2/ years. She has synthesized a large lot of α-deoxyadenosine, isolated a large batch of both the R and S isomer of cyclodeoxyadenosine and has capped the α-deoxyadenonsine for use in a DNA synthesizer that uses phosphoramidite chemistry. In November 1987, Dr. Andrzej Surowiec joined our unit as a Visiting Research Assistant Professor. Dr. Surowiec has a MS degree in electrical engineering and did his Ph.D. in Biophysics studying the conductivity of DNA in dilute solution. He has been performing the helix-coil transition experiments. In November 1987, Dr. Steven Swarts also joined our unit as a Postdoctoral Fellow. He received his Ph.D. from Oakland University under Dr. Michael Sevilla with whom we have a collaboration studying the induction of base damage in hydrated DNA. Dr. Swarts has a strong background in spectroscopy and, therefore, was a key individual for determination of the limitations of the HPLC assays and the establishment of a GC/MS capability equivalent to Dr. M. Dizdaroglu at the National Bureau of Standards. 9 refs., 1 tab

  9. Modeling of cladding and fuel motion in a loss of flow situation for GCFR safety analysis. Technical progress report (annual), June 15, 1974--March 15, 1975

    International Nuclear Information System (INIS)

    Eggen, D.T.

    1975-01-01

    During the first nine months of the project, methods and apparatus were developed to study the freezeout of molten cladding in a cooler blanket region. Three tests were run in which a mass of molten material from a simulated core region of a GCFR flowed into a bundle of simulated blanket elements. In all cases plugging occurred in or before the first grid-spacer. Theories and preliminary models are in accord with these observations. These tests have been done with a 50/50-Pb/Sn alloy simulating the cladding and spacer grids and alumina simulating the fuel. Materials are being obtained for tests with stainless steel cladding and spacers. Development is progressing well on an electrically-heated fuel element which will be used to study the melting and motion of cladding in the core region for a loss of flow accident. Preliminary models is being developed to calculate the motion and freezeout of flowing cladding in the blanket region. The SAS-GAS and Argus codes are being adapted for uses in conjunction with model development on the project. A survey of fission gas effects in oxide during TOP cases was prepared and other codes (LIFE) were reviewed for possible value on the project. A set of reference physical parameters is being developed for the various materials used in the analysis and experiments. (U.S.)

  10. Development of innovative techniques and principles that may be used as models to improve plant performance. Technical progress report, February 1, 1990--January 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Hanna, W.W.; Burton, G.W.

    1992-06-01

    Methods and techniques for transferring germplasm from wild to cultivated species are being developed. The transferred germplasm is being shown to be valuable in plant breeding and in cultivar development. In the primary gene pool of the grassy Pennisetum glaucum subspecies monodii germplasm, some cytoplasms are being identified that appear to have significant effects on forage yields and morphological characteristics. One cytoplasm, A{sub 4}, is very stable for male sterility and fertility is not easily restored by other lines. It should be a valuable cytoplasm for producing commercial forage hybrids. Disease resistance and yield genes transferred from monodii to cultivated pearl millet lines are having a major impact on increasing production of animals grazing disease resistant Tifleaf 2 pearl millet. Genes controlling resistance to many of the world-wide diseases on pearl millet are being identified in the monodii germplasm. Valuable germplasm has been transferred from the secondary gene pool P. purpuroum) which is used as the pollinator of the first pearl millet grain hybrid in the US Production of 7-chromosome gametes in 42-chromosome interspecific hybrids appears to be genotype specific and makes possible transfer of germplasm from the secondary gene pool to cultivated diploid pearl millet. Significant progress has been made in transferring genes controlling apomixis from P. squamulatum (tertiary gene pool) to cultivated pearl millet. Highly apomictic BC{sub 4} plants have been recovered, one of which sets five times as much seed as the best BC{sub 3} plant.

  11. Technical report writing today

    CERN Document Server

    Riordan, Daniel G

    2014-01-01

    "Technical Report Writing Today" provides thorough coverage of technical writing basics, techniques, and applications. Through a practical focus with varied examples and exercises, students internalize the skills necessary to produce clear and effective documents and reports. Project worksheets help students organize their thoughts and prepare for assignments, and focus boxes highlight key information and recent developments in technical communication. Extensive individual and collaborative exercises expose students to different kinds of technical writing problems and solutions. Annotated student examples - more than 100 in all - illustrate different writing styles and approaches to problems. Numerous short and long examples throughout the text demonstrate solutions for handling writing assignments in current career situations. The four-color artwork in the chapter on creating visuals keeps pace with contemporary workplace capabilities. The Tenth Edition offers the latest information on using electronic resum...

  12. Technical writing versus technical writing

    Science.gov (United States)

    Dillingham, J. W.

    1981-01-01

    Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

  13. Investigation of sulfur-tolerant catalysts for selective synthesis of hydrocarbon liquids from coal-derived gases. Annual technical progress report, September 19, 1980-September 18, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Bartholomew, C.H.

    1981-10-31

    During the past contract year, considerable progress was made in characterization and activity/selectivity testing of iron and cobalt catalysts. Preparation of boride promoted cobalt and iron catalysts was refined and nearly completed. H/sub 2/ and CO adsorption and oxygen titration measurements were performed on a number of supported and unsupported catalysts, especially several boride promoted cobalt and iron catalysts. Activity/selectivity tests of 3 and 15% Fe/SiO/sub 2/ and Co/SiO/sub 2/ and of 6 borided cobalt and iron catalysts were completed. The product distributions for iron and cobalt boride catalysts are unusual and interesting. Boron promoted iron is more active and stable than iron/silica; cobalt boride has an unusually high selectivity for alcohols. Tests to determine effects of H/sub 2/S poisoning on activity/selectivity properties of 15% Co/SiO/sub 2/ indicate that a significant loss of activity occurs over a period of 24 to 28 h in the presence of 10 to 20 ppM H/sub 2/S. Product selectivity to liquids increased through a maximum during the gradual addition of sulfur. Reactant CO and H/sub 2/S interact partially to form COS which is less toxic than H/sub 2/S. H/sub 2/ and CO adsorption data were obtained for 3, 6 and 9% Co/ZSM-5 catalysts prepared and reactor tested by PETC. The unusual and interesting results suggest that metal-support interactions may have an important influence on reactant adsorption properties.

  14. Recent technical progress in the French uranium industry; Les recents progres techniques dans l'industrie de l'uranium en France

    Energy Technology Data Exchange (ETDEWEB)

    Huet, H. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1961-07-01

    This paper reviews the present-day uranium production situation in France. The various stages of the treatment the concentrates receive, leading to the final production of the metal, are described briefly: dissolution, purification by extraction with a mixture of tributyl phosphate and white spirit, precipitation with ammonia, drying and calcination of the trioxide, reduction with hydrogen, cracked ammonia or preferably pure ammonia gas, fluorination with anhydrous hydrofluoric acid, and production of the metal by the calcium thermite process. Recent work of an original nature is discussed in greater detail. (author) [French] L'expose fait le point de la technique actuelle en ce qui concerne la fabrication de l'uranium en France. Il retrace brievement les diverses etapes du traitement des concentres pour aboutir au metal: mise en solution, purification par extraction au melange phosphate de tributylo-white spirit, precipitation par l'ammoniaque, sechage et calcination du trioxyde, reduction a l'hydrogene, a l'ammoniac craque ou mieux au gaz ammoniac pur, fluoruration par l'acide fluorhydrique anhydre et elaboration du metal par calciothermie. De plus amples details sont donnes sur les realisations recentes d'un caractere original. (auteur)

  15. Recent technical progress in the French uranium industry; Les recents progres techniques dans l'industrie de l'uranium en France

    Energy Technology Data Exchange (ETDEWEB)

    Huet, H [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1961-07-01

    This paper reviews the present-day uranium production situation in France. The various stages of the treatment the concentrates receive, leading to the final production of the metal, are described briefly: dissolution, purification by extraction with a mixture of tributyl phosphate and white spirit, precipitation with ammonia, drying and calcination of the trioxide, reduction with hydrogen, cracked ammonia or preferably pure ammonia gas, fluorination with anhydrous hydrofluoric acid, and production of the metal by the calcium thermite process. Recent work of an original nature is discussed in greater detail. (author) [French] L'expose fait le point de la technique actuelle en ce qui concerne la fabrication de l'uranium en France. Il retrace brievement les diverses etapes du traitement des concentres pour aboutir au metal: mise en solution, purification par extraction au melange phosphate de tributylo-white spirit, precipitation par l'ammoniaque, sechage et calcination du trioxyde, reduction a l'hydrogene, a l'ammoniac craque ou mieux au gaz ammoniac pur, fluoruration par l'acide fluorhydrique anhydre et elaboration du metal par calciothermie. De plus amples details sont donnes sur les realisations recentes d'un caractere original. (auteur)

  16. Direct synthesis of 2-methyl-1-propanol/methanol fuels and feedstocks: Quarterly technical progress report for the period June--August 1985

    Energy Technology Data Exchange (ETDEWEB)

    Klier, K.; Herman, R. G.; Simmons, G. W.; Nunan, J.; Himelfarb, P. B.

    1985-09-01

    During the present quarter, and intensive series of aluminum- supported catalysts, both Cs promoted and unpromoted, have been prepared by a special preparation technique and tested to determine alcohol synthesis activity, selectivities, and stability. Preparation of a single-phase hydrotalcite-like ((Cu/sub x/Zn/sub 1 -x/)/sub 6/Al/sub 2/CO/sub 3/(OH)/sub 16//center dot/4H/sub 2/O) catalyst precursor has been successfully accomplished. Some of these catalysts have been tested to determine their activities in producing methanol and higher alcohols. It has been observed that catalysts obtained by calcination and reduction of the hydrotalcite-like precursor are very active methanol synthesis catalysts. Doping these catalysts with cesium in an aqueous solution leads to initial deactivation, which is partially recovered by doping at higher cesium levels. Results give us guidelines for altering the promoter doping procedure so that a more active and selective aluminum-supported higher alcohol synthesis catalyst will be obtained. 4 refs., 13 figs., 13 tabs.

  17. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    John Ross

    2003-04-30

    The Final Technical Report summarizes research accomplishments and Publications in the period of 5/1/99 to 4/30/03 done on the grant. Extensive progress was made in the period covered by this report in the areas of chemical kinetics of non-linear systems; spatial structures, reaction - diffusion systems, and thermodynamic and stochastic theory of electrochemical and general systems.

  18. Design, Synthesis, and Mechanistic Evaluation of Iron-Based Catalysis for Synthesis Gas Conversion to Fuels and Chemicals. Technical Progress Report

    International Nuclear Information System (INIS)

    Akio Ishikawa; Manuel Ojeda; Nan Yao; Enrique Iglesia

    2006-01-01

    area promoter. The kinetic behavior of these materials, specifically the effects of H 2 , CO, and CO 2 on the rates and selectivities of Fischer-Tropsch synthesis reactions has led to a new proposal for the nature of rate-determining steps on Fe and Co Fischer-Tropsch catalysts, and more specifically to the roles of hydrogen-assisted and alkali-assisted dissociation of CO in determining rates and CO 2 selectivities. Finally, we have started an exploratory study of the use of colloidal precipitation methods for the synthesis of small Fe and Co clusters using recently developed methods. During this period, we have had to restrict manpower assigned to this project because some irregularities in reporting and communications have led to the interruption of funding during this period. This has led to less than optimal productivity and to significant disruptions of the technical work. These issues have also led to significant underspending of project funds during this reporting period and to our consequent request for a no-cost extension of one year, which we understand has been granted

  19. Experimental investigation of the chemistry of excited states of rare gases. Annual technical progress report, October 15, 1976--October 14, 1977

    International Nuclear Information System (INIS)

    Setser, D.W.

    1978-01-01

    Tunable dye laser fluorescence has been combined with the flowing afterglow technique as a method for studying reactive intermediates present in the flowing afterglow. The radiative lifetimes and two-body quenching rate constants (with Ar carrier gas) for the Ar*(3p 5 ,4p) and Ar*(3p 5 ,5p) excited states were reported in the preceding year. During this year, we have measured the Ar* product states from the two-body quenching. More than 50% of the quenching leads directly to intermultiplet transfer to Ar(4s) states, rather than to intramultiplet cascade down the Ar(4p) manifold. Using this technique we also have studied the Xe(5p 5 ,6p') and Xe(5p 5 ,7p) excited states and radiative lifetimes, two-body quenching and the product states from quenching have been ascertained. These data should be of value for modeling energy flow pathways of rare gases excited by high energy electrons. A method has been developed for studying the quenching of the XeF(B) and KrF(B) by a variety of reagent molecules. A preliminary account of this work was published (number 5 in the publication list). Much additional experimental work has been done and a definitive study of the electronic quenching of XeF(B) and KrF(B) is in progress. Efforts to interpret (and publish) our comprehensive studies of the reactive quenching of the Kr( 3 P 2 ) and Xe( 3 P 2 ) by fluorine and chlorine-containing molecules has continued (see numbers 4, 6 and 8 in the publication listing). Two more manuscripts are in final stages of preparation. Of particular importance has been the development of methods for simulating and interpreting the bound-free emission spectra from the very high vibrational levels of the xenon and krypton fluorides and chlorides. Experiments have been done to measure the branching ratios for (i) ArF* formation from reactive quenching of Ar( 3 P 2 ) with fluorine-containing reagents and (ii) KrBr* and Br* formation for Kr( 3 P 2 ) reacting with some bromine-containing molecules

  20. Plutonium, cesium, uranium, and thorium series radionuclides in the Hudson River estuary and other environments. Annual technical progress report, December 1, 1981-November 30, 1982

    International Nuclear Information System (INIS)

    Simpson, H.J.; Trier, R.M.; Anderson, R.F.

    1982-01-01

    Radionuclide activities were measured in a large number of sediment cores and suspended particle samples throughout the salinity range of the Hudson River estuary. Activities of 137 Cs, 134 Cs and 60 Co determined by gamma spectrometry and 239 240 Pu and 238 Pu determined by alpha spectrometry indicate reasonably rapid accumulation rates in the sediments of marginal cove areas, and very rapid deposition in the harbor region adjacent to New York City, resulting in 239 240 Pu accumulations there more than an order of magnitude greater than the fallout delivery rate. Fallout 239 240 Pu moving downstream in the Hudson appears to be almost completely retained within the system by particle deposition, while 80 to 90% of the 137 Cs derived from both reactor releases and fallout has been exported to the coastal waters in solution. Measurements of fallout 239 240 Pu in a saline lake with a high carbonate ion concentration yielded water column activities about two orders of magnitude greater than has been found for fallout plutonium in other continental waters, indicating extensive mobility in some natural water environments. Experiments using lake water suggest that carbonate ion is likely to be a critical factor in regulating plutonium solubility in some environments and that low molecular weight complexes are primarily responsible for enhanced plutonium solubility. Activities of several other nuclides of interest in radioactive waste management ( 238 U, 234 U, 232 Th, 230 Th, 228 Th, 231 Pa) were also found to be orders of magnitude greater in high carbonate waters than in other natural waters

  1. Plutonium, cesium and uranium series radionuclides in the Hudson River estuary and other environments. Annual technical progress report, December 1, 1979-November 30, 1980

    International Nuclear Information System (INIS)

    Simpson, H.J.; Trier, R.M.; Olsen, C.R.

    1980-01-01

    Radionuclide activities were measured in a large number of sediment cores and suspended particle samples throughout the salinity range of the Hudson River estuary. Activities of 137 Cs, 134 Cs and 60 Co determined by gamma spectrometry and 239 240 Pu and 238 Pu determined by alpha spectrometry indicate reasonably rapid accumulation rates in the sediments of marginal cove areas, and very rapid deposition in the harbor region adjacent to New York City, resulting in 239 240 Pu accumulations there more than an order of magnitude greater than the fallout delivery rate. Measurable amounts of reactor-derived 134 Cs and 60 Co are found in nearly al sediment samples containing appreciable 137 Cs between 15 km upstream of Indian Point and the downstream extent of our sampling about 70 km south of the reactor. Fallout 239 240 Pu reaching the Hudson appears to be almost completely retained within the systems by particle deposition, while 70 to 90% of the 137 Cs derived from both reactor releases and fallout has been exported to the coastal waters in solution. Activity levels of 239 240 Pu in New York harbor sediments indicate a significant source in addition to suspended particles carried down the Hudson. The most likely cause appears to be transport into the estuary of particles from offshore waters having higher specific activities of 239 240 Pu. Measurements of fallout 239 240 Pu in a saline lake with a high carbonate ion concentration yielded water column activities about two orders of magnitude greater than has been found for fallout plutonium in other continental waters, indicating extensive mobility in some natural water environments. Experiments using lake water suggest that carbonate ion may indeed be a critical factor in regulating plutonium solubility and that low molecular weight complexes are primarily responsible for enhanced plutonium solubility

  2. Plutonium, cesium and uranium series radionuclides in the Hudson River estuary and other environments. Annual technical progress report, December 1, 1979-November 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, H. J.; Trier, R. M.; Olsen, C. R.

    1980-01-01

    Radionuclide activities were measured in a large number of sediment cores and suspended particle samples throughout the salinity range of the Hudson River estuary. Activities of /sup 137/Cs, /sup 134/Cs and /sup 60/Co determined by gamma spectrometry and /sup 239/ /sup 240/Pu and /sup 238/Pu determined by alpha spectrometry indicate reasonably rapid accumulation rates in the sediments of marginal cove areas, and very rapid deposition in the harbor region adjacent to New York City, resulting in /sup 239/ /sup 240/Pu accumulations there more than an order of magnitude greater than the fallout delivery rate. Measurable amounts of reactor-derived /sup 134/Cs and /sup 60/Co are found in nearly al sediment samples containing appreciable /sup 137/Cs between 15 km upstream of Indian Point and the downstream extent of our sampling about 70 km south of the reactor. Fallout /sup 239/ /sup 240/Pu reaching the Hudson appears to be almost completely retained within the systems by particle deposition, while 70 to 90% of the /sup 137/Cs derived from both reactor releases and fallout has been exported to the coastal waters in solution. Activity levels of /sup 239/ /sup 240/Pu in New York harbor sediments indicate a significant source in addition to suspended particles carried down the Hudson. The most likely cause appears to be transport into the estuary of particles from offshore waters having higher specific activities of /sup 239/ /sup 240/Pu. Measurements of fallout /sup 239/ /sup 240/Pu in a saline lake with a high carbonate ion concentration yielded water column activities about two orders of magnitude greater than has been found for fallout plutonium in other continental waters, indicating extensive mobility in some natural water environments. Experiments using lake water suggest that carbonate ion may indeed be a critical factor in regulating plutonium solubility and that low molecular weight complexes are primarily responsible for enhanced plutonium solubility.

  3. ISABELLE: a progress report

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, H

    1980-01-01

    This paper discusses the ISABELLE project, which has the objective of constructing a high-energy proton colliding beam facility at Brookhaven National Laboratory. The major technical features of the intersecting storage accelerators with their projected performance are described. Application of over 1000 superconducting magnets in the two rings represents the salient characteristic of the machine. The status of the entire project, the technical progress made so far, and difficulties encountered are reviewed.

  4. ISABELLE: a progress report

    International Nuclear Information System (INIS)

    Hahn, H.

    1980-01-01

    This paper discusses the ISABELLE project, which has the objective of constructing a high-energy proton colliding beam facility at Brookhaven National Laboratory. The major technical features of the intersecting storage accelerators with their projected performance are described. Application of over 1000 superconducting magnets in the two rings represents the salient characteristic of the machine. The status of the entire project, the technical progress made so far, and difficulties encountered are reviewed

  5. Innovation Incubator: LiquidCool Solutions Technical Evaluation. Laboratory Study and Demonstration Results of a Directed-Flow, Liquid Submerged Server for High-Efficiency Data Centers

    Energy Technology Data Exchange (ETDEWEB)

    Kozubal, Eric J [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-12-12

    LiquidCool Solutions (LCS) has developed liquid submerged server (LSS) technology that changes the way computer electronics are cooled. The technology provides an option to cool electronics by the direct contact flow of dielectric fluid (coolant) into a sealed enclosure housing all the electronics of a single server. The intimate dielectric fluid contact with electronics improves the effectiveness of heat removal from the electronics.

  6. Solution preparation

    International Nuclear Information System (INIS)

    Seitz, M.G.

    1982-01-01

    Reviewed in this statement are methods of preparing solutions to be used in laboratory experiments to examine technical issues related to the safe disposal of nuclear waste from power generation. Each approach currently used to prepare solutions has advantages and any one approach may be preferred over the others in particular situations, depending upon the goals of the experimental program. These advantages are highlighted herein for three approaches to solution preparation that are currently used most in studies of nuclear waste disposal. Discussion of the disadvantages of each approach is presented to help a user select a preparation method for his particular studies. Also presented in this statement are general observations regarding solution preparation. These observations are used as examples of the types of concerns that need to be addressed regarding solution preparation. As shown by these examples, prior to experimentation or chemical analyses, laboratory techniques based on scientific knowledge of solutions can be applied to solutions, often resulting in great improvement in the usefulness of results

  7. The improvement of near-term CdTe processing and product capabilities and establishment of next-generation CdTe technology. Annual technical progress report, September 1, 1995--August 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Kester, J.; Albright, S. [Golden Photon, Inc., CO (United States)

    1997-07-01

    The potential of photovoltaics to become a major global business enterprise still lingers outside the limits of industrial capabilities. For the Cadmium Sulfide/Cadmium Telluride (CdS/CdTe) system this potential has continued to focus on improvements in efficiency, stability, and cost reduction. This triad is the primary objective of the present subcontract with NREL entitled {open_quotes}The Improvement of Near-term CdTe Processing and Product Capabilities & Establishment of Next Generation CdTe Technology{close_quotes}. This subcontract represents an intermediate stage of NREL`s plan to assist the growth of the photovoltaic industry in overcoming the scientific and technical barriers to commercialization. This report outlines the progress that has been made during the period of August 1995 through August 1996. The objectives of this subcontract are to improve processing methods, quantify and understand efficiency improvement mechanisms, meet life-testing goals, and address cadmium safety concerns. Task and subtask goals are defined to meet these objectives in specific areas. The approach to fulfilling the subcontract goals is through a balanced plan of process improvement and mechanism identification. These are carried out and continued through monitoring under various long term and accelerated stress conditions. GPI maintains an on-going awareness of all safety related issues, can in particular, those involving cadmium.

  8. US/Japan collaborative program on fusion reactor materials: Summary of the tenth DOE/JAERI Annex I technical progress meeting on neutron irradiation effects in first wall and blanket structural materials

    International Nuclear Information System (INIS)

    Rowcliffe, A.F.

    1989-01-01

    This meeting was held at Oak Ridge National Laboratory on March 17, 1989, to review the technical progress on the collaborative DOE/JAERI program on fusion reactor materials. The purpose of the program is to determine the effects of neutron irradiation on the mechanical behavior and dimensional stability of US and Japanese austenitic stainless steels. Phase I of the program focused on the effects of high concentrations of helium on the tensile, fatigue, and swelling properties of both US and Japanese alloys. In Phase II of the program, spectral and isotropic tailoring techniques are fully utilized to reproduce the helium:dpa ratio typical of the fusion environment. The Phase II program hinges on a restart of the High Flux Isotope Reactor by mid-1989. Eight target position capsules and two RB* position capsules have been assembled. The target capsule experiments will address issues relating to the performance of austenitic steels at high damage levels including an assessment of the performance of a variety of weld materials. The RB* capsules will provide a unique and important set of data on the behavior of austenitic steels irradiated under conditions which reproduce the damage rate, dose, temperature, and helium generation rate expected in the first wall and blanket structure of the International Thermonuclear Experimental Reactor

  9. Nuclear Physics Laboratory technical progress report

    International Nuclear Information System (INIS)

    1991-01-01

    This contract supports broadly based experimental work in intermediate energy nuclear physics. The program includes pion- nucleon studies at TRIUMF and LAMPF, inelastic pion scattering and charge exchange reactions at LAMPF, and nucleon charge exchange at LAMPF/NTOF. The first results of spin-transfer observables in the isovector (rvec p,rvec n) reaction are included in this report. Our data confirm the tentative result from (rvec p,rvec p) reactions that the nuclear isovector spin response shows neither longitudinal enhancement nor transverse quenching. Our program in quasifree scattering of high energy pions shows solid evidence of isoscalar enhancement of the nuclear nonspin response. We include several comparisons of the quasifree scattering of different probes. Results from our efforts in the design of accelerator RF cavities are also included in this report

  10. Technical progress - a chance for the future

    Energy Technology Data Exchange (ETDEWEB)

    Schubert, J

    1981-12-01

    The insufficient acceptance of technology in the society of today has its roots in the past century when a humanistically oriented education system had superseded the practice-oriented way. The emotional refusal of science and technology resulting herefrom caused some difficulties when new technologies, as e.g. microelectronics, were introduced. As microelectronics is rated as a basic innovation it entails social and economic changes.

  11. MRS feasibility assessment grant technical progress report

    International Nuclear Information System (INIS)

    1993-01-01

    On January 13, 1993, Governor of the State of Utah, Mike Leavitt officially announced that he was opposing a MRS Facility in the State of Utah and informed San Juan County of his decision which will preclude the County from applying for a Phase IIa feasibility grant. A copy of the policy statement made by Governor Leavitt is included in this report. Additionally, a bill in the State House of Representative has been filed opposing the facility. A copy of the bill is also included. The work accomplished under Phase I, indicated that there was about an equal amount of residents in San Juan County opposed and in favor of the facility. There were many concerns and issues presented during the Phase I grant period that would have been continued to Phase IIa, if allowed, including the citizen committee

  12. Regional cooperation to stimulate technical progress

    International Nuclear Information System (INIS)

    Ridvan, M.; Ehjrej, P.L.

    1987-01-01

    The main principles of the IAEA regional agreement on co-operation in the field of researches, elaboration and training of specialists in nuclear science and engineering for the states of Asia and Pacific Ocean region (RAC) and of the ARCAL program in Latin America are considered. The RAC projects envisage co-operation in the field of medicine (radiotherapy and nuclear methods, sterilization, etc.), agriculture (nuclear methods, raising of plants, using radiation mutations, food irradiation, etc.), industry (application of isotopes and radiation technology) and others. The ARCAL projects comprise radiation protection, nuclear control instruments, nuclear analytic methods, radioimmune analysis in stock-breeding, product irradiation, nuclear information, etc

  13. Technical progress in nuclear medical heart diagnosis

    International Nuclear Information System (INIS)

    Standke, R.; Hoer, G.

    1989-01-01

    The rapid development in nuclear cardiology worldwide can hardly be surveyed from the point of view of one center. In connection with the general nuclear cardiologic development this study describes a multiparameter analysis of regional left ventricular function during exercise, and the method of sectoranalysis for quantification of myocardial SPECT. Finally a one-step procedure to quantify left ventricular function and myocardial perfusion is presented. (orig.) [de

  14. Quarterly Technical Progress Report June 2015

    Energy Technology Data Exchange (ETDEWEB)

    Buchholz, Bruce A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-06-08

    The project has two main goals: 1) Identify the types of adducts naphthalene (NA) forms with DNA and 2) determine whether adduct formation correlates with site selective tumor formation in defined subcompartments of the respiratory tract (respiratory and olfactory nasal epithelium and airways of mice, rats and rhesus monkeys). Five tasks are associated with the completion of the goals. Task 1: Contracting and Animal Use Approvals. IACUC and ACURO approvals are complete, The subcontract with UC Davis (UCD) was executed in December 2014. Task 2: Perform In Vitro Study for Goal 1. Rat samples exposed and in freezer while adduct standards are being made. Mouse samples need to be exposed in next quarter. Task 3: Perform In Vitro Study for Goal 2. Mouse ex vivo samples completed. Rat and monkey samples need to be completed in the next quarter. Task 4: Sample Preparation and Analysis. Mouse Goal 2 samples completed. Other samples remain to be done. Task 5: Data Interpretation and Reporting. Need rat data to write paper on adduct formation.

  15. Operational Group Sandy technical progress report

    Science.gov (United States)

    ,

    2013-01-01

    Hurricane Sandy made US landfall near Atlantic City, NJ on 29 October 2012, causing 72 direct deaths, displacing thousands of individuals from damaged or destroyed dwellings, and leaving over 8.5 million homes without power across the northeast and mid-Atlantic. To coordinate federal rebuilding activities in the affected region, the President established the cabinet-level Hurricane Sandy Rebuilding Task Force (Task Force). The Task Force was charged with identifying opportunities for achieving rebuilding success while supporting economic vitality, improving public health and safety, protecting and enhancing natural and manmade infrastructure, bolstering resilience, and ensuring appropriate accountability.

  16. Imagining Technicities

    DEFF Research Database (Denmark)

    Liboriussen, Bjarke; Plesner, Ursula

    2011-01-01

    to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... in cooperation and development of ICTs seems to pass unnoticed. However, since they are aligned into ICTs, technicities impact innovation....

  17. OIL SOLUTIONS POWDER

    Science.gov (United States)

    Technical product bulletin: aka OIL SOLUTIONS POWDER, SPILL GREEN LS, this miscellaneous oil spill control agent used in cleanups initially behaves like a synthetic sorbent, then as a solidifier as the molecular microencapsulating process occurs.

  18. Progress report 1979

    International Nuclear Information System (INIS)

    1980-12-01

    This progress report deals with technical and research work done at the AAEC Research Establishment in the twelve month period ending September 30, 1979. Work done in the following research divisions is reported: Applied Maths and Computing, Chemical Technology, Engineering Research, Environmental Science, Instrumentation and Control, Isotope, Materials and Physics

  19. Function Allocation in Complex Socio-Technical Systems: Procedure usage in nuclear power and the Context Analysis Method for Identifying Design Solutions (CAMIDS) Model

    Science.gov (United States)

    Schmitt, Kara Anne

    This research aims to prove that strict adherence to procedures and rigid compliance to process in the US Nuclear Industry may not prevent incidents or increase safety. According to the Institute of Nuclear Power Operations, the nuclear power industry has seen a recent rise in events, and this research claims that a contributing factor to this rise is organizational, cultural, and based on peoples overreliance on procedures and policy. Understanding the proper balance of function allocation, automation and human decision-making is imperative to creating a nuclear power plant that is safe, efficient, and reliable. This research claims that new generations of operators are less engaged and thinking because they have been instructed to follow procedures to a fault. According to operators, they were once to know the plant and its interrelations, but organizationally more importance is now put on following procedure and policy. Literature reviews were performed, experts were questioned, and a model for context analysis was developed. The Context Analysis Method for Identifying Design Solutions (CAMIDS) Model was created, verified and validated through both peer review and application in real world scenarios in active nuclear power plant simulators. These experiments supported the claim that strict adherence and rigid compliance to procedures may not increase safety by studying the industry's propensity for following incorrect procedures, and when it directly affects the outcome of safety or security of the plant. The findings of this research indicate that the younger generations of operators rely highly on procedures, and the organizational pressures of required compliance to procedures may lead to incidents within the plant because operators feel pressured into following the rules and policy above performing the correct actions in a timely manner. The findings support computer based procedures, efficient alarm systems, and skill of the craft matrices. The solution to

  20. KSC Technical Capabilities Website

    Science.gov (United States)

    Nufer, Brian; Bursian, Henry; Brown, Laurette L.

    2010-01-01

    This document is the website pages that review the technical capabilities that the Kennedy Space Center (KSC) has for partnership opportunities. The purpose of this information is to make prospective customers aware of the capabilities and provide an opportunity to form relationships with the experts at KSC. The technical capabilities fall into these areas: (1) Ground Operations and Processing Services, (2) Design and Analysis Solutions, (3) Command and Control Systems / Services, (4) Materials and Processes, (5) Research and Technology Development and (6) Laboratories, Shops and Test Facilities.