Rock suitability classification RSC 2012

International Nuclear Information System (INIS)

McEwen, T.; Kapyaho, A.; Hella, P.; Aro, S.; Kosunen, P.; Mattila, J.; Pere, T.

2012-12-01

This report presents Posiva's Rock Suitability Classification (RSC) system, developed for locating suitable rock volumes for repository design and construction. The RSC system comprises both the revised rock suitability criteria and the procedure for the suitability classification during the construction of the repository. The aim of the classification is to avoid such features of the host rock that may be detrimental to the favourable conditions within the repository, either initially or in the long term. This report also discusses the implications of applying the RSC system for the fulfilment of the regulatory requirements concerning the host rock as a natural barrier and the site's overall suitability for hosting a final repository of spent nuclear fuel

Combined LAURA-UPS solution procedure for chemically-reacting flows. M.S. Thesis

Science.gov (United States)

Wood, William A.

1994-01-01

A new procedure seeks to combine the thin-layer Navier-Stokes solver LAURA with the parabolized Navier-Stokes solver UPS for the aerothermodynamic solution of chemically-reacting air flowfields. The interface protocol is presented and the method is applied to two slender, blunted shapes. Both axisymmetric and three dimensional solutions are included with surface pressure and heat transfer comparisons between the present method and previously published results. The case of Mach 25 flow over an axisymmetric six degree sphere-cone with a noncatalytic wall is considered to 100 nose radii. A stability bound on the marching step size was observed with this case and is attributed to chemistry effects resulting from the noncatalytic wall boundary condition. A second case with Mach 28 flow over a sphere-cone-cylinder-flare configuration is computed at both two and five degree angles of attack with a fully-catalytic wall. Surface pressures are seen to be within five percent with the present method compared to the baseline LAURA solution and heat transfers are within 10 percent. The effect of grid resolution is investigated and the nonequilibrium results are compared with a perfect gas solution, showing that while the surface pressure is relatively unchanged by the inclusion of reacting chemistry the nonequilibrium heating is 25 percent higher. The procedure demonstrates significant, order of magnitude reductions in solution time and required memory for the three dimensional case over an all thin-layer Navier-Stokes solution.

EXTRAPOLATING THE SUITABILITY OF SOILS AS NATURAL REACTORS USING AN EXISTING SOIL MAP: APPLICATION OF PEDOTRANSFER FUNCTIONS, SPATIAL INTEGRATION AND VALIDATION PROCEDURES

Directory of Open Access Journals (Sweden)

Yameli Guadalupe Aguilar Duarte

2011-04-01

Full Text Available The aim of this study was the spatial identification of the suitability of soils as reactors in the treatment of swine wastewater in the Mexican state of Yucatan, as well as the development of a map with validation procedures. Pedotransfer functions were applied to the existing soils database. A methodological approach was adopted that allowed the spatialization of pedotransfer function data points. A map of the suitability of soil associations as reactors was produced, as well as a map of the level of accuracy of the associations using numerical classification technique, such as discriminant analysis. Soils with the highest suitability indices were found to be Vertisols, Stagnosols, Nitisols and Luvisols. Some 83.9% of the area of Yucatan is marginally suitable for the reception of swine wastewater, 6.5% is moderately suitable, while 6% is suitable. The percentages of the spatial accuracy of the pedotransfer functions range from 62% to 95% with an overall value of 71.5%. The methodological approach proved to be practical, accurate and inexpensive.

Suitability of customer relationship management systems for the management of study participants in biomedical research.

Science.gov (United States)

Schwanke, J; Rienhoff, O; Schulze, T G; Nussbeck, S Y

2013-01-01

Longitudinal biomedical research projects study patients or participants over a course of time. No IT solution is known that can manage study participants, enhance quality of data, support re-contacting of participants, plan study visits, and keep track of informed consent procedures and recruitments that may be subject to change over time. In business settings management of personal is one of the major aspects of customer relationship management systems (CRMS). To evaluate whether CRMS are suitable IT solutions for study participant management in biomedical research. Three boards of experts in the field of biomedical research were consulted to get an insight into recent IT developments regarding study participant management systems (SPMS). Subsequently, a requirements analysis was performed with stakeholders of a major biomedical research project. The successive suitability evaluation was based on the comparison of the identified requirements with the features of six CRMS. Independently of each other, the interviewed expert boards confirmed that there is no generic IT solution for the management of participants. Sixty-four requirements were identified and prioritized in a requirements analysis. The best CRMS was able to fulfill forty-two of these requirements. The non-fulfilled requirements demand an adaption of the CRMS, consuming time and resources, reducing the update compatibility, the system's suitability, and the security of the CRMS. A specific solution for the SPMS is favored instead of a generic and commercially-oriented CRMS. Therefore, the development of a small and specific SPMS solution was commenced and is currently on the way to completion.

A geometric improvement of the velocity-pressure local regularity criterion for a suitable weak solution to the Navier-Stokes equations

Czech Academy of Sciences Publication Activity Database

Neustupa, Jiří

2014-01-01

Roč. 139, č. 4 (2014), s. 685-698 ISSN 0862-7959 R&D Projects: GA ČR GA13-00522S Institutional support: RVO:67985840 Keywords : Navier-Stokes equation * suitable weak solution * regularity Subject RIV: BA - General Mathematics http://hdl.handle.net/10338.dmlcz/144145

Measurement of Actinides in Molybdenum-99 Solution Analytical Procedure

International Nuclear Information System (INIS)

Soderquist, Chuck Z.; Weaver, Jamie L.

2015-01-01

This document is a companion report to a previous report, PNNL 24519, Measurement of Actinides in Molybdenum-99 Solution, A Brief Review of the Literature, August 2015. In this companion report, we report a fast, accurate, newly developed analytical method for measurement of trace alpha-emitting actinide elements in commercial high-activity molybdenum-99 solution. Molybdenum-99 is widely used to produce 99m Tc for medical imaging. Because it is used as a radiopharmaceutical, its purity must be proven to be extremely high, particularly for the alpha emitting actinides. The sample of 99 Mo solution is measured into a vessel (such as a polyethylene centrifuge tube) and acidified with dilute nitric acid. A gadolinium carrier is added (50 µg). Tracers and spikes are added as necessary. Then the solution is made strongly basic with ammonium hydroxide, which causes the gadolinium carrier to precipitate as hydrous Gd(OH) 3 . The precipitate of Gd(OH) 3 carries all of the actinide elements. The suspension of gadolinium hydroxide is then passed through a membrane filter to make a counting mount suitable for direct alpha spectrometry. The high-activity 99 Mo and 99m Tc pass through the membrane filter and are separated from the alpha emitters. The gadolinium hydroxide, carrying any trace actinide elements that might be present in the sample, forms a thin, uniform cake on the surface of the membrane filter. The filter cake is first washed with dilute ammonium hydroxide to push the last traces of molybdate through, then with water. The filter is then mounted on a stainless steel counting disk. Finally, the alpha emitting actinide elements are measured by alpha spectrometry.

Evaluation of solution procedures for material and/or geometrically nonlinear structural analysis by the direct stiffness method.

Science.gov (United States)

Stricklin, J. A.; Haisler, W. E.; Von Riesemann, W. A.

1972-01-01

This paper presents an assessment of the solution procedures available for the analysis of inelastic and/or large deflection structural behavior. A literature survey is given which summarized the contribution of other researchers in the analysis of structural problems exhibiting material nonlinearities and combined geometric-material nonlinearities. Attention is focused at evaluating the available computation and solution techniques. Each of the solution techniques is developed from a common equation of equilibrium in terms of pseudo forces. The solution procedures are applied to circular plates and shells of revolution in an attempt to compare and evaluate each with respect to computational accuracy, economy, and efficiency. Based on the numerical studies, observations and comments are made with regard to the accuracy and economy of each solution technique.

Measurement of Actinides in Molybdenum-99 Solution Analytical Procedure

Energy Technology Data Exchange (ETDEWEB)

Soderquist, Chuck Z. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Weaver, Jamie L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-11-01

This document is a companion report to a previous report, PNNL 24519, Measurement of Actinides in Molybdenum-99 Solution, A Brief Review of the Literature, August 2015. In this companion report, we report a fast, accurate, newly developed analytical method for measurement of trace alpha-emitting actinide elements in commercial high-activity molybdenum-99 solution. Molybdenum-99 is widely used to produce ^99mTc for medical imaging. Because it is used as a radiopharmaceutical, its purity must be proven to be extremely high, particularly for the alpha emitting actinides. The sample of ⁹⁹Mo solution is measured into a vessel (such as a polyethylene centrifuge tube) and acidified with dilute nitric acid. A gadolinium carrier is added (50 µg). Tracers and spikes are added as necessary. Then the solution is made strongly basic with ammonium hydroxide, which causes the gadolinium carrier to precipitate as hydrous Gd(OH)₃. The precipitate of Gd(OH)₃ carries all of the actinide elements. The suspension of gadolinium hydroxide is then passed through a membrane filter to make a counting mount suitable for direct alpha spectrometry. The high-activity ⁹⁹Mo and ^99mTc pass through the membrane filter and are separated from the alpha emitters. The gadolinium hydroxide, carrying any trace actinide elements that might be present in the sample, forms a thin, uniform cake on the surface of the membrane filter. The filter cake is first washed with dilute ammonium hydroxide to push the last traces of molybdate through, then with water. The filter is then mounted on a stainless steel counting disk. Finally, the alpha emitting actinide elements are measured by alpha spectrometry.

Evaluation of Persian Professional Web Social Networks\\\\\\' Features, to Provide a Suitable Solution for Optimization of These Networks in Iran

Directory of Open Access Journals (Sweden)

Nadjla Hariri

2013-03-01

Full Text Available This study aimed to determine the status of Persian professional web social networks' features and provide a suitable solution for optimization of these networks in Iran. The research methods were library research and evaluative method, and study population consisted of 10 Persian professional web social networks. In this study, for data collection, a check list of social networks important tools and features was used. According to the results, “Cloob”, “IR Experts” and “Doreh” were the most compatible networks with the criteria of social networks. Finally, some solutions were presented for optimization of capabilities of Persian professional web social networks.

Solution-mediated cladding doping of commercial polymer optical fibers

Science.gov (United States)

Stajanca, Pavol; Topolniak, Ievgeniia; Pötschke, Samuel; Krebber, Katerina

2018-03-01

Solution doping of commercial polymethyl methacrylate (PMMA) polymer optical fibers (POFs) is presented as a novel approach for preparation of custom cladding-doped POFs (CD-POFs). The presented method is based on a solution-mediated diffusion of dopant molecules into the fiber cladding upon soaking of POFs in a methanol-dopant solution. The method was tested on three different commercial POFs using Rhodamine B as a fluorescent dopant. The dynamics of the diffusion process was studied in order to optimize the doping procedure in terms of selection of the most suitable POF, doping time and conditions. Using the optimized procedure, longer segment of fluorescent CD-POF was prepared and its performance was characterized. Fiber's potential for sensing and illumination applications was demonstrated and discussed. The proposed method represents a simple and cheap way for fabrication of custom, short to medium length CD-POFs with various dopants.

Characteristics and suitability of waste dump sites in Owerri, Nigeria ...

African Journals Online (AJOL)

A five point criteria screening of the three major waste dumpsites in Owerri Municipality was identified, and a ranking procedure adopted to determine the suitability or otherwise of the dumpsites. The sites were screened and ranked hydro-geologically and geo-technically in order of suitable, moderately suitable, and not ...

A PROCEDURAL SOLUTION TO MODEL ROMAN MASONRY STRUCTURES

Directory of Open Access Journals (Sweden)

V. Cappellini

2013-07-01

Full Text Available The paper will describe a new approach based on the development of a procedural modelling methodology for archaeological data representation. This is a custom-designed solution based on the recognition of the rules belonging to the construction methods used in roman times. We have conceived a tool for 3D reconstruction of masonry structures starting from photogrammetric surveying. Our protocol considers different steps. Firstly we have focused on the classification of opus based on the basic interconnections that can lead to a descriptive system used for their unequivocal identification and design. Secondly, we have chosen an automatic, accurate, flexible and open-source photogrammetric pipeline named Pastis Apero Micmac – PAM, developed by IGN (Paris. We have employed it to generate ortho-images from non-oriented images, using a user-friendly interface implemented by CNRS Marseille (France. Thirdly, the masonry elements are created in parametric and interactive way, and finally they are adapted to the photogrammetric data. The presented application, currently under construction, is developed with an open source programming language called Processing, useful for visual, animated or static, 2D or 3D, interactive creations. Using this computer language, a Java environment has been developed. Therefore, even if the procedural modelling reveals an accuracy level inferior to the one obtained by manual modelling (brick by brick, this method can be useful when taking into account the static evaluation on buildings (requiring quantitative aspects and metric measures for restoration purposes.

a Procedural Solution to Model Roman Masonry Structures

Science.gov (United States)

Cappellini, V.; Saleri, R.; Stefani, C.; Nony, N.; De Luca, L.

2013-07-01

The paper will describe a new approach based on the development of a procedural modelling methodology for archaeological data representation. This is a custom-designed solution based on the recognition of the rules belonging to the construction methods used in roman times. We have conceived a tool for 3D reconstruction of masonry structures starting from photogrammetric surveying. Our protocol considers different steps. Firstly we have focused on the classification of opus based on the basic interconnections that can lead to a descriptive system used for their unequivocal identification and design. Secondly, we have chosen an automatic, accurate, flexible and open-source photogrammetric pipeline named Pastis Apero Micmac - PAM, developed by IGN (Paris). We have employed it to generate ortho-images from non-oriented images, using a user-friendly interface implemented by CNRS Marseille (France). Thirdly, the masonry elements are created in parametric and interactive way, and finally they are adapted to the photogrammetric data. The presented application, currently under construction, is developed with an open source programming language called Processing, useful for visual, animated or static, 2D or 3D, interactive creations. Using this computer language, a Java environment has been developed. Therefore, even if the procedural modelling reveals an accuracy level inferior to the one obtained by manual modelling (brick by brick), this method can be useful when taking into account the static evaluation on buildings (requiring quantitative aspects) and metric measures for restoration purposes.

Suitability of Varicose Veins for Endovenous Treatments

International Nuclear Information System (INIS)

Goode, S. D.; Kuhan, G.; Altaf, N.; Simpson, R.; Beech, A.; Richards, T.; MacSweeney, S. T.; Braithwaite, B. D.

2009-01-01

The aim of the study was to assess the suitability of radiofrequency ablation (RFA), endovenous laser ablation (EVLA), and foam sclerotherapy (FS) for patients with symptomatic varicose veins (VVs). The study comprised 403 consecutive patients with symptomatic VVs. Data on 577 legs from 403 consecutive patients with symptomatic VVs were collected for the year 2006. Median patient age was 55 years (interquartile range 45-66), and 62% patients were women. A set of criteria based on duplex ultrasonography was used to select patients for each procedure. Great saphenous vein (GSV) reflux was present in 77% (446 of 577) of legs. Overall, 328 (73%) of the legs were suitable for at least one of the endovenous options. Of the 114 legs with recurrent GSV reflux disease, 83 (73%) were suitable to receive endovenous therapy. Patients with increasing age were less likely to be suitable for endovenous therapy (P = 0.03). Seventy-three percent of patients with VVs caused by GSV incompetence are suitable for endovenous therapy.

Updating QR factorization procedure for solution of linear least squares problem with equality constraints.

Science.gov (United States)

Zeb, Salman; Yousaf, Muhammad

2017-01-01

In this article, we present a QR updating procedure as a solution approach for linear least squares problem with equality constraints. We reduce the constrained problem to unconstrained linear least squares and partition it into a small subproblem. The QR factorization of the subproblem is calculated and then we apply updating techniques to its upper triangular factor R to obtain its solution. We carry out the error analysis of the proposed algorithm to show that it is backward stable. We also illustrate the implementation and accuracy of the proposed algorithm by providing some numerical experiments with particular emphasis on dense problems.

Solutions For Smart Metering Under Harsh Environmental Condicions

Directory of Open Access Journals (Sweden)

Kunicina N.

2015-02-01

Full Text Available The described case study concerns application of wireless sensor networks to the smart control of power supply substations. The solution proposed for metering is based on the modular principle and has been tested in the intersystem communication paradigm using selectable interface modules (IEEE 802.3, ISM radio interface, GSM/GPRS. The solution modularity gives 7 % savings of maintenance costs. The developed solution can be applied to the control of different critical infrastructure networks using adapted modules. The proposed smart metering is suitable for outdoor installation, indoor industrial installations, operation under electromagnetic pollution, temperature and humidity impact. The results of tests have shown a good electromagnetic compatibility of the prototype meter with other electronic devices. The metering procedure is exemplified by operation of a testing company's workers under harsh environmental conditions.

QFD Based Benchmarking Logic Using TOPSIS and Suitability Index

Directory of Open Access Journals (Sweden)

Jaeho Cho

2015-01-01

Full Text Available Users’ satisfaction on quality is a key that leads successful completion of the project in relation to decision-making issues in building design solutions. This study proposed QFD (quality function deployment based benchmarking logic of market products for building envelope solutions. Benchmarking logic is composed of QFD-TOPSIS and QFD-SI. QFD-TOPSIS assessment model is able to evaluate users’ preferences on building envelope solutions that are distributed in the market and may allow quick achievement of knowledge. TOPSIS (Technique for Order of Preference by Similarity to Ideal Solution provides performance improvement criteria that help defining users’ target performance criteria. SI (Suitability Index allows analysis on suitability of the building envelope solution based on users’ required performance criteria. In Stage 1 of the case study, QFD-TOPSIS was used to benchmark the performance criteria of market envelope products. In Stage 2, a QFD-SI assessment was performed after setting user performance targets. The results of this study contribute to confirming the feasibility of QFD based benchmarking in the field of Building Envelope Performance Assessment (BEPA.

[Effects of different types and concentration of oral sweet solution on reducing neonatal pain during heel lance procedures].

Science.gov (United States)

Leng, Hong-yao; Zheng, Xian-lan; Yan, Li; Zhang, Xian-hong; He, Hua-yun; Xiang, Ming

2013-09-01

To compare the effect of different types and concentrations of sweet solutions on neonatal pain during heel lance procedure. Totally 560 full term neonates (male 295, female 265) were randomized into 7 groups:placebo group (plain water), 10% glucose, 25% glucose, 50% glucose, 12% sucrose, 24% sucrose and 30% sucrose groups.In each group, 2 ml corresponding oral solutions were administered through a syringe by dripping into the neonate's mouth 2 minute before heel lance. The procedure process was recorded by videos, from which to collect heart rate, oxygen saturation and pain score 1 min before puncture, 3, 5 and 10 min after puncture. The average heart rate increase 3, 5 and 10 min after procedure in the 25% and 50% glucose groups, 12% and 24% and 30% sucrose groups was significantly lower than those in the placebo group (P lance (both P lance, but the best concentration of sucrose for pain relief needs further study.

Analytical solution to the 1D Lemaitre's isotropic damage model and plane stress projected implicit integration procedure

DEFF Research Database (Denmark)

Andriollo, Tito; Thorborg, Jesper; Hattel, Jesper Henri

2016-01-01

obtaining an integral relationship between total strain and effective stress. By means of the generalized binomial theorem, an expression in terms of infinite series is subsequently derived. The solution is found to simplify considerably existing techniques for material parameters identification based...... on optimization, as all issues associated with classical numerical solution procedures of the constitutive equations are eliminated. In addition, an implicit implementation of the plane stress projected version of Lemaitre's model is discussed, showing that the resulting algebraic system can be reduced...

Solution procedure and performance evaluation for a water–LiBr absorption refrigeration machine

International Nuclear Information System (INIS)

Wonchala, Jason; Hazledine, Maxwell; Goni Boulama, Kiari

2014-01-01

The water–lithium bromide absorption cooling machine was investigated theoretically in this paper. A detailed solution procedure was proposed and validated. A parametric study was conducted over the entire admissible ranges of the desorber, condenser, absorber and evaporator temperatures. The performance of the machine was evaluated based on the circulation ratio which is a measure of the system size and cost, the first law coefficient of performance and the second law exergy efficiency. The circulation ratio and the coefficient of performance were seen to improve as the temperature of the heat source increased, while the second law performance deteriorated. The same qualitative responses were obtained when the temperature of the refrigerated environment was increased. On the other hand, simultaneously raising the condenser and absorber temperatures was seen to result in a severe deterioration of both the circulation ratio and first law coefficient of performance, while the second law performance indicator improved significantly. The influence of the difference between the condenser and absorber exit temperatures, as well as that of the internal recovery heat exchanger on the different performance indicators was also calculated and discussed. - Highlights: • Analysis of a water–LiBr absorption machine, including detailed solution procedure. • Performance assessed using first and second law considerations, as well as flow ratio. • Effects of heat source and refrigerated environment temperatures on the performance. • Effects of the difference between condenser and absorber temperatures. • Effects of internal heat exchanger efficiency on overall cooling machine performance

Suitability

NARCIS (Netherlands)

Bokdam, J.; Braeckel, van A.

2002-01-01

The suitability of grazing, burning, mowing and cutting as tools for succession control in peatland was assessed and expressed on a scale from 0 - 1. All management tools are suitable, but their effects are conditional. The suitability depends on the targeted vegetation transition and on their

Solution Procedure for Transport Modeling in Effluent Recharge Based on Operator-Splitting Techniques

Directory of Open Access Journals (Sweden)

Shutang Zhu

2008-01-01

Full Text Available The coupling of groundwater movement and reactive transport during groundwater recharge with wastewater leads to a complicated mathematical model, involving terms to describe convection-dispersion, adsorption/desorption and/or biodegradation, and so forth. It has been found very difficult to solve such a coupled model either analytically or numerically. The present study adopts operator-splitting techniques to decompose the coupled model into two submodels with different intrinsic characteristics. By applying an upwind finite difference scheme to the finite volume integral of the convection flux term, an implicit solution procedure is derived to solve the convection-dominant equation. The dispersion term is discretized in a standard central-difference scheme while the dispersion-dominant equation is solved using either the preconditioned Jacobi conjugate gradient (PJCG method or Thomas method based on local-one-dimensional scheme. The solution method proposed in this study is applied to the demonstration project of groundwater recharge with secondary effluent at Gaobeidian sewage treatment plant (STP successfully.

Computer assisted procedure maintenance

International Nuclear Information System (INIS)

Bisio, R.; Hulsund, J. E.; Nilsen, S.

2004-04-01

The maintenance of operating procedures in a NPP is a tedious and complicated task. Through the whole life cycle of the procedures they will be dynamic, 'living' documents. Several aspects of the procedure must be considered in a revision process. Pertinent details and attributes of the procedure must be checked. An organizational structure must be created and responsibilities allotted for drafting, revising, reviewing and publishing procedures. Available powerful computer technology provides solutions within document management and computerisation of procedures. These solutions can also support the maintenance of procedures. Not all parts of the procedure life cycle are equally amenable to computerized support. This report looks at the procedure life cycle in todays NPPs and discusses the possibilities associated with introduction of computer technology to assist the maintenance of procedures. (Author)

Emotion Monitoring – Verification of Physiological Characteristics Measurement Procedures

Directory of Open Access Journals (Sweden)

Landowska Agnieszka

2014-12-01

Full Text Available This paper concerns measurement procedures on an emotion monitoring stand designed for tracking human emotions in the Human-Computer Interaction with physiological characteristics. The paper addresses the key problem of physiological measurements being disturbed by a motion typical for human-computer interaction such as keyboard typing or mouse movements. An original experiment is described, that aimed at practical evaluation of measurement procedures performed at the emotion monitoring stand constructed at GUT. Different locations of sensors were considered and evaluated for suitability and measurement precision in the Human- Computer Interaction monitoring. Alternative locations (ear lobes and forearms for skin conductance, blood volume pulse and temperature sensors were proposed and verified. Alternative locations proved correlation with traditional locations as well as lower sensitiveness to movements like typing or mouse moving, therefore they can make a better solution for monitoring the Human-Computer Interaction.

Survey of a numerical procedure for the solution of hyperbolic systems of three dimensional fluid flow

International Nuclear Information System (INIS)

Graf, U.

1986-01-01

A combination of several numerical methods is used to construct a procedure for effective calculation of complex three-dimensional fluid flow problems. The split coefficient matrix (SCM) method is used so that the differenced equations of the hyperbolic system do not disturb correct signal propagation. The semi-discretisation of the equations of the SCM method is done with the asymmetric, separated region, weighted residual (ASWR) method to give accurate solutions on a relatively coarse mesh. For the resulting system of ordinary differential equations, a general-purpose ordinary differential equation solver is used in conjunction with a method of fractional steps for an economic solution of the large system of linear equations. (orig.) [de

A procedure for preferential trapping of cesium cations from aqueous solutions and their separation from other inorganic cations

International Nuclear Information System (INIS)

Plesek, J.; Hermanek, S.; Selucky, P.; Williams, R.E.

1995-01-01

The title procedure is as follows. Deltahedral heteroborane anions are added to the aqueous solution containing cesium ions, precipitate (if any) is separated off, and the cesium salts involving the deltahedral heteroborane anions are trapped on activated carbon. The cobaltocarborane anion [3-Co-(1,2-C 2 B 9 H 11 ) 2 ] and/or its substitution derivatives are particularly well suited to this purpose. The process can find use in the separation of radionuclides present in waste solutions arising from spent nuclear fuel treatment. (P.A.). 1 fig

An improved ashing procedure for biologic sample

Energy Technology Data Exchange (ETDEWEB)

Zongmei, Wu [Zhejiang Province Enviromental Radiation Monitoring Centre (China)

1992-07-01

The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches.

An improved ashing procedure for biologic sample

International Nuclear Information System (INIS)

Wu Zongmei

1992-01-01

The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches

Sn approach applied to the solution of transport equation

International Nuclear Information System (INIS)

Lopes, J.P.

1973-09-01

In this work the origin of the Transport Theory is considered and the Transport Equation for the movement of the neutron in a system is established in its more general form, using the laws of nuclear physics. This equation is used as the starting point for development, under adequate assumptions, of simpler models that render the problem suitable for numerical solution. Representation of this model in different geometries is presented. The different processes of nuclear physics are introduced briefly and discussed. In addition, the boundary conditions for the different cases and a general procedure for the application of the Conservation Law are stated. The last chapter deals specifically with the S n method, its development, definitions and generalities. Computational schemes for obtaining the S n solution in spherical and cylindrical geometry, and convergence acceleration methods are also developed. (author)

A procedure for multi-objective optimization of tire design parameters

Directory of Open Access Journals (Sweden)

Nikola Korunović

2015-04-01

Full Text Available The identification of optimal tire design parameters for satisfying different requirements, i.e. tire performance characteristics, plays an essential role in tire design. In order to improve tire performance characteristics, formulation and solving of multi-objective optimization problem must be performed. This paper presents a multi-objective optimization procedure for determination of optimal tire design parameters for simultaneous minimization of strain energy density at two distinctive zones inside the tire. It consists of four main stages: pre-analysis, design of experiment, mathematical modeling and multi-objective optimization. Advantage of the proposed procedure is reflected in the fact that multi-objective optimization is based on the Pareto concept, which enables design engineers to obtain a complete set of optimization solutions and choose a suitable tire design. Furthermore, modeling of the relationships between tire design parameters and objective functions based on multiple regression analysis minimizes computational and modeling effort. The adequacy of the proposed tire design multi-objective optimization procedure has been validated by performing experimental trials based on finite element method.

Magnetic analysis of tokamak plasma with approximate MHD equilibrium solution

International Nuclear Information System (INIS)

Moriyama, Shin-ichi; Hiraki, Naoji

1993-01-01

A magnetic analysis method for determining equilibrium configuration parameters (plasma shape, poloidal beta and internal inductance) on a non-circular tokamak is described. The feature is to utilize an approximate MHD equilibrium solution which explicitly relates the configuration parameters with the magnetic fields picked up by magnetic sensors. So this method is suitable for the real-time analysis performed during a tokamak discharge. A least-squares fitting procedure is added to the analytical algorithm in order to reduce the errors in the magnetic analysis. The validity is investigated through the numerical calculation for a tokamak equilibrium model. (author)

Parallel iterative procedures for approximate solutions of wave propagation by finite element and finite difference methods

Energy Technology Data Exchange (ETDEWEB)

Kim, S. [Purdue Univ., West Lafayette, IN (United States)

1994-12-31

Parallel iterative procedures based on domain decomposition techniques are defined and analyzed for the numerical solution of wave propagation by finite element and finite difference methods. For finite element methods, in a Lagrangian framework, an efficient way for choosing the algorithm parameter as well as the algorithm convergence are indicated. Some heuristic arguments for finding the algorithm parameter for finite difference schemes are addressed. Numerical results are presented to indicate the effectiveness of the methods.

Habitat Suitability Index Models: Red-winged blackbird

Science.gov (United States)

Short, Henry L.

1985-01-01

A review and synthesis of existing information were used to develop a Habitat Suitability Index (HSI) model for the red-winged blackbird (Agelaius phoeniceus L.). The model consolidates habitat use information into a framework appropriate for field application, and is scaled to produce an index between 0.0 (unsuitable habitat) to 1.0 (optimum habitat). HSI models are designed to be used with Habitat Evaluation Procedures previously developed by the U.S. Fish and Wildlife Service.

Optimization in the utility maximization framework for conservation planning: a comparison of solution procedures in a study of multifunctional agriculture

Science.gov (United States)

Kreitler, Jason R.; Stoms, David M.; Davis, Frank W.

2014-01-01

Quantitative methods of spatial conservation prioritization have traditionally been applied to issues in conservation biology and reserve design, though their use in other types of natural resource management is growing. The utility maximization problem is one form of a covering problem where multiple criteria can represent the expected social benefits of conservation action. This approach allows flexibility with a problem formulation that is more general than typical reserve design problems, though the solution methods are very similar. However, few studies have addressed optimization in utility maximization problems for conservation planning, and the effect of solution procedure is largely unquantified. Therefore, this study mapped five criteria describing elements of multifunctional agriculture to determine a hypothetical conservation resource allocation plan for agricultural land conservation in the Central Valley of CA, USA. We compared solution procedures within the utility maximization framework to determine the difference between an open source integer programming approach and a greedy heuristic, and find gains from optimization of up to 12%. We also model land availability for conservation action as a stochastic process and determine the decline in total utility compared to the globally optimal set using both solution algorithms. Our results are comparable to other studies illustrating the benefits of optimization for different conservation planning problems, and highlight the importance of maximizing the effectiveness of limited funding for conservation and natural resource management.

Regional flow and solute transport modeling for site suitability. Part I

International Nuclear Information System (INIS)

Rowe, J.; Miller, I.

1979-12-01

The nature of regional flow systems in large sedimentary basins will largely determine the effectiveness of regional flow as a barrier to radionuclide escape from deep geologic repositories. The purpose of the work reported herein and the proposed future work is to develop a methodology for evaluating regional flow barriers by using numerical models. The Williston Basin was chosen as an archetype case for the regional modeling study. However, due to the simplified nature of the study, the results are not meant to represent the behavior of a repository actually placed within the Williston Basin. The major components of this Phase I study are: (1) assembly and reduction of available data; (2) formulation of a simplified geohydrologic model; (3) computer simulation of fluid flow; and (4) computer simulation of solute transport. As of this report, the first two items are essentially completed. Computer simulation of fluid flow will require some revision and further study, which will be done in the second phase of this study. Computer simulation of solute transport has been considered only on a very preliminary basis. Important conclusions of this Phase I study are as follows. Assembly and reduction of data require an extensive work effort. Generally, the parameters describing fluid flow are poorly known on a regional basis and those describing solute transport are unknown

Regional flow and solute transport modeling for site suitability. Part I

Energy Technology Data Exchange (ETDEWEB)

Rowe, J.; Miller, I.

1979-12-01

The nature of regional flow systems in large sedimentary basins will largely determine the effectiveness of regional flow as a barrier to radionuclide escape from deep geologic repositories. The purpose of the work reported herein and the proposed future work is to develop a methodology for evaluating regional flow barriers by using numerical models. The Williston Basin was chosen as an archetype case for the regional modeling study. However, due to the simplified nature of the study, the results are not meant to represent the behavior of a repository actually placed within the Williston Basin. The major components of this Phase I study are: (1) assembly and reduction of available data; (2) formulation of a simplified geohydrologic model; (3) computer simulation of fluid flow; and (4) computer simulation of solute transport. As of this report, the first two items are essentially completed. Computer simulation of fluid flow will require some revision and further study, which will be done in the second phase of this study. Computer simulation of solute transport has been considered only on a very preliminary basis. Important conclusions of this Phase I study are as follows. Assembly and reduction of data require an extensive work effort. Generally, the parameters describing fluid flow are poorly known on a regional basis and those describing solute transport are unknown.

A procedure to create isoconcentration surfaces in low-chemical-partitioning, high-solute alloys

International Nuclear Information System (INIS)

Hornbuckle, B.C.; Kapoor, M.; Thompson, G.B.

2015-01-01

A proximity histogram or proxigram is the prevailing technique of calculating 3D composition profiles of a second phase in atom probe tomography. The second phase in the reconstruction is delineated by creating an isoconcentration surface, i.e. the precipitate–matrix interface. The 3D composition profile is then calculated with respect to this user-defined isoconcentration surface. Hence, the selection of the correct isoconcentration surface is critical. In general, the preliminary selection of an isoconcentration value is guided by the visual observation of a chemically partitioned second phase. However, in low-chemical -partitioning systems, such a visual guide is absent. The lack of a priori composition information of the precipitate phase may further confound the issue. This paper presents a methodology of selecting an appropriate elemental species and subsequently obtaining an isoconcentration value to create an accurate isoconcentration surface that will act as the precipitate–matrix interface. We use the H-phase precipitate in the Ni–Ti–Hf shape memory alloy as our case study to illustrate the procedure. - Highlights: • A procedure for creating accurate isoconcentration surface for low-chemical-partitioning, high-solute alloys. • Determine the appropriate element to create the isosconcentration surface. • Subsequently identify the accurate isoconcentration value to create an isoconcentration surface.

Payment Procedures for Electronic Government Services

OpenAIRE

Pousttchi, Key; Wiedemann, Dietmar Georg

2005-01-01

In this paper, we analyse payment procedures for their suitability for electronic government. We provide an overview of the payment procedures currently available on the market, compare the situation in electronic government with the situation in electronic commerce and analyze what we can transfer. Based on functional requirements we propose a scheme that allows public agencies to examine the appropriateness of any given payment procedure for electronic government.

Saturated salt solution method: a useful cadaver embalming for surgical skills training.

Science.gov (United States)

Hayashi, Shogo; Homma, Hiroshi; Naito, Munekazu; Oda, Jun; Nishiyama, Takahisa; Kawamoto, Atsuo; Kawata, Shinichi; Sato, Norio; Fukuhara, Tomomi; Taguchi, Hirokazu; Mashiko, Kazuki; Azuhata, Takeo; Ito, Masayuki; Kawai, Kentaro; Suzuki, Tomoya; Nishizawa, Yuji; Araki, Jun; Matsuno, Naoto; Shirai, Takayuki; Qu, Ning; Hatayama, Naoyuki; Hirai, Shuichi; Fukui, Hidekimi; Ohseto, Kiyoshige; Yukioka, Tetsuo; Itoh, Masahiro

2014-12-01

This article evaluates the suitability of cadavers embalmed by the saturated salt solution (SSS) method for surgical skills training (SST). SST courses using cadavers have been performed to advance a surgeon's techniques without any risk to patients. One important factor for improving SST is the suitability of specimens, which depends on the embalming method. In addition, the infectious risk and cost involved in using cadavers are problems that need to be solved. Six cadavers were embalmed by 3 methods: formalin solution, Thiel solution (TS), and SSS methods. Bacterial and fungal culture tests and measurement of ranges of motion were conducted for each cadaver. Fourteen surgeons evaluated the 3 embalming methods and 9 SST instructors (7 trauma surgeons and 2 orthopedists) operated the cadavers by 21 procedures. In addition, ultrasonography, central venous catheterization, and incision with cauterization followed by autosuture stapling were performed in some cadavers. The SSS method had a sufficient antibiotic effect and produced cadavers with flexible joints and a high tissue quality suitable for SST. The surgeons evaluated the cadavers embalmed by the SSS method to be highly equal to those embalmed by the TS method. Ultrasound images were clear in the cadavers embalmed by both the methods. Central venous catheterization could be performed in a cadaver embalmed by the SSS method and then be affirmed by x-ray. Lungs and intestines could be incised with cauterization and autosuture stapling in the cadavers embalmed by TS and SSS methods. Cadavers embalmed by the SSS method are sufficiently useful for SST. This method is simple, carries a low infectious risk, and is relatively of low cost, enabling a wider use of cadavers for SST.

Staining Potential of Neo MTA Plus, MTA Plus, and Biodentine Used for Pulpotomy Procedures.

Science.gov (United States)

Camilleri, Josette

2015-07-01

Mineral trioxide aggregate (MTA) used for pulpotomy procedures in immature permanent teeth can reduce treatment to 1 session as opposed to classic calcium hydroxide therapy, which necessitates multiple appointments. The main disadvantage of MTA use is crown discoloration after treatment. The aim of this study was to characterize 3 materials that are used for pulpotomy procedures in immature permanent teeth and assess their color stability in the presence of sodium hypochlorite solution. Hydrated Neo MTA Plus (Avalon Biomed Inc, Bradenton, FL), MTA Plus (Avalon Biomed Inc), and Biodentine (Septodont, Saint-Maur-des-Fossés, France) were characterized after immersion in Hank's balanced salt solution for 1 day and 28 days using a combination of scanning electron microscopy, energy-dispersive spectroscopy, and X-ray diffraction analysis. The color stability of the 3 materials in contact with water or sodium hypochlorite was evaluated by photography, spectrophotometry, and X-ray diffraction analysis. All the materials hydrated and produced calcium hydroxide as a by-product of hydration at early age. All materials interacted with synthetic tissue fluid, forming a calcium phosphate phase. MTA Plus exhibited discoloration in contact with sodium hypochlorite. All the materials tested are suitable to be used in the treatment of immature teeth because they all produced calcium hydroxide, which is necessary to induce dentin bridge formation and continued root formation. Neo MTA Plus and Biodentine are suitable alternatives to MTA, and they do not exhibit discoloration. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

The environmental suitability of industrial secondary products used as covering materials in landfills

International Nuclear Information System (INIS)

Laine-Ylijoki, J.; Wahlstroem, M.; Maekelae, E.

2001-01-01

The industrial secondary products and landmasses polluted in a minor way can be used as coverings and sealing materials and also restricted in the ground construction of landfills. By using suitable secondary products, natural materials can be reduced. Substitutes are needed due to the fact that the availability of natural materials is poor in many areas. The presented project is a part of the Streams technology programme financed by Tekes. It includes the development of the measuring methods to study the environmental suitability of industrial secondary products, which will be used as covering materials of landfills. Based on the results, a handbook addressing the environmental suitability procedure will be compiled

Photography in Dermatologic Surgery: Selection of an Appropriate Lighting Solution for a Particular Clinical Application.

Science.gov (United States)

Chen, Brian R; Poon, Emily; Alam, Murad

2018-01-01

Lighting is an important component of consistent, high-quality dermatologic photography. There are different types of lighting solutions available. To evaluate currently available lighting equipment and methods suitable for procedural dermatology. Overhead lighting, built-in camera flashes, external flash units, studio strobes, and light-emitting diode (LED) light panels were evaluated with regard to their utility for dermatologic surgeons. A set of ideal lighting characteristics was used to examine the capabilities and limitations of each type of lighting solution. Recommendations regarding lighting solutions and optimal usage configurations were made in terms of the context of the clinical environment and the purpose of the image. Overhead lighting may be a convenient option for general documentation. An on-camera lighting solution using a built-in camera flash or a camera-mounted external flash unit provides portability and consistent lighting with minimal training. An off-camera lighting solution with studio strobes, external flash units, or LED light panels provides versatility and even lighting with minimal shadows and glare. The selection of an optimal lighting solution is contingent on practical considerations and the purpose of the image.

A Wronskian of Jost solutions

International Nuclear Information System (INIS)

Corona-Corona, Gulmaro

2004-01-01

Based on the standard fact that any matrix potential u=u(x) determines a family of Jost solutions whose parameter runs analytically (continuously) on the (closed) half planes, respectively, the zeros of a suitable matrix valued Wronskian of a Jost solution pair are explored

Incompressible Navier-Stokes and parabolized Navier-Stokes solution procedures and computational techniques

Science.gov (United States)

Rubin, S. G.

1982-01-01

Recent developments with finite-difference techniques are emphasized. The quotation marks reflect the fact that any finite discretization procedure can be included in this category. Many so-called finite element collocation and galerkin methods can be reproduced by appropriate forms of the differential equations and discretization formulas. Many of the difficulties encountered in early Navier-Stokes calculations were inherent not only in the choice of the different equations (accuracy), but also in the method of solution or choice of algorithm (convergence and stability, in the manner in which the dependent variables or discretized equations are related (coupling), in the manner that boundary conditions are applied, in the manner that the coordinate mesh is specified (grid generation), and finally, in recognizing that for many high Reynolds number flows not all contributions to the Navier-Stokes equations are necessarily of equal importance (parabolization, preferred direction, pressure interaction, asymptotic and mathematical character). It is these elements that are reviewed. Several Navier-Stokes and parabolized Navier-Stokes formulations are also presented.

Site Suitability Analysis for Beekeeping via Analythical Hyrearchy Process, Konya Example

Science.gov (United States)

Sarı, F.; Ceylan, D. A.

2017-11-01

Over the past decade, the importance of the beekeeping activities has been emphasized in the field of biodiversity, ecosystems, agriculture and human health. Thus, efficient management and deciding correct beekeeping activities seems essential to maintain and improve productivity and efficiency. Due to this importance, considering the economic contributions to the rural area, the need for suitability analysis concept has been revealed. At this point, Multi Criteria Decision Analysis (MCDA) and Geographical Information Systems (GIS) integration provides efficient solutions to the complex structure of decision- making process for beekeeping activities. In this study, site suitability analysis via Analytical Hierarchy Process (AHP) was carried out for Konya city in Turkey. Slope, elevation, aspect, distance to water resources, roads and settlements, precipitation and flora criteria are included to determine suitability. The requirements, expectations and limitations of beekeeping activities are specified with the participation of experts and stakeholders. The final suitability map were validated with existing 117 beekeeping locations and Turkish Statistical Institute 2016 beekeeping statistics for Konya province.

A procedure to construct exact solutions of nonlinear evolution ...

Indian Academy of Sciences (India)

Exact solutions; the functional variable method; nonlinear wave equations. PACS Nos 02.30. ... computer science, directly searching for solutions of nonlinear differential equations has become more and ... Right after this pioneer work, this ...

A fuzzy approach to a multiple criteria and geographical information system for decision support on suitable locations for biogas plants

DEFF Research Database (Denmark)

Franco de los Rios, Camilo Andres; Bojesen, Mikkel; Hougaard, Jens Leth

The purpose of this paper is to model the multi-criteria decision problem of identifying the most suitable facility locations for biogas plants under an integrated decision support methodology. Here the Geographical Information System (GIS) is used for measuring the attributes of the alternatives...... according to a given set of criteria. Measurements are taken in interval form, expressing the natural imprecision of common data, and the Fuzzy Weighted Overlap Dominance (FWOD) procedure is applied for aggregating and exploiting this kind of data, obtaining suitability degrees for every alternative....... The estimation of criteria weights, which is necessary for applying the FWOD procedure, is done by means of the Analytical Hierarchy Process (AHP), such that a combined AHP-FWOD methodology allows identifying the more suitable sites for building biogas plants. We show that the FWOD relevance-ranking procedure...

An exact solution procedure for multi-item two-echelon spare parts inventory control problem with batch ordering in the central warehouse

NARCIS (Netherlands)

Topan, E.; Bayindir, Z.P.; Tan, T.

2009-01-01

We consider a multi-item two-echelon inventory system in which the central warehouse operates under a (Q; R) policy, and the local warehouses implement basestock policy. An exact solution procedure is proposed to find the inventory control policy parameters that minimize the system-wide inventory

Mapping of suitable zones for manual drilling as a possible solution to increase access to drinking water in Africa through integration of systematized GIS data and local knowledge

Science.gov (United States)

Fussi, Fabio; Alvino, Roberta; Caruba, Massimo; Galimberti, Luca; Marzan, Ignacio; Tarrason y Cerda', David; Sabatini, Daniela

2013-04-01

In several African countries water supply is still largely a huge problem. In order to achieve MDG for water supply, UNICEF is promoting manual drilling in Africa. Manual drilling refers to those techniques of drilling boreholes for groundwater exploitation using human or animal power (not mechanized equipment). These techniques are well known in countries with large alluvial deposits (India, Nepal, Bangladesh, etc). They are cheaper than mechanized boreholes, easy to implement as the equipment is locally done, able to provide clean water if correctly applied. But manual drilling is feasible only where suitable hydrogeological conditions are met: - the shallow geological layers are not too hard (soft sediments or rocks having limited resistance) and have good permeability; - the depth where it is possible to find exploitable water is limited (in this study we assumed no deeper than 25 m). For this reason mapping of suitable zone for manual drilling has been the first step in UNICEF program already completed in 15 countries. this paper explains the general methodology for the identification of suitable zones at country level The methodology is based in the integration of different information (maps, reports, database) already existing in each country, together with interview of local technicians with direct experience in various regions and limited direct field data collection. General suitability for manual drilling (although adapted to specific condition in each country) is based on the combination of three main parameters: the geological suitability, the suitability according to water depth and the morphological suitability: - Geological suitability is related to the hardness and permeability of the shallow layers of rock formations. It has been obtained through a GIS procedure of simplification and reclassification of geological maps, estimating hardness and permeability of main rock and overlaying weathered layer on the basis of stratigraphic borehole logs

Cr(OH)3-NPs-CNC hybrid nanocomposite: a sorbent for adsorptive removal of methylene blue and malachite green from solutions.

Science.gov (United States)

Nekouei, Farzin; Nekouei, Shahram; Keshtpour, Farzaneh; Noorizadeh, Hossein; Wang, Shaobin

2017-11-01

In this article, Cr(OH) 3 nanoparticle-modified cellulose nanocrystal (CNC) as a novel hybrid nanocomposite (Cr(OH) 3 -NPs-CNC) was prepared by a simple procedure and used as a sorbent for adsorptive removal of methylene blue (MB) and malachite green (MG) from aqueous solution. Different kinetic models were tested, and the pseudo-second-order kinetic model was found more suitable for the MB and MG adsorption processes. The BET and Langmuir models were more suitable for the adsorption processes of MB and MG. Thermodynamic studies suggested that the adsorption of MB and MG onto Cr(OH) 3 -NPs-CNC nanocomposite was a spontaneous and endothermic process. The maximum adsorption capacities for MB and MG were reached 106 and 104 mg/g, respectively, which were almost two times higher than unmodified CNC. The chemical stability and leaching tests of the Cr(OH) 3 -NPs-CNC hybrid nanocomposite showed that only small amounts of chromium were leached into the solution.

Proceedings of a workshop on fish habitat suitability index models

Science.gov (United States)

Terrell, James W.

1984-01-01

One of the habitat-based methodologies for impact assessment currently in use by the U.S. Fish and Wildlife Service is the Habitat Evaluation Procedures (HEP) (U.S. Fish and Wildlife Service 1980). HEP is based on the assumption that the quality of an area as wildlife habitat at a specified target year can be described by a single number, called a Habitat Suitability Index (HSI). An HSI of 1.0 represents optimum habitat: an HSI of 0.0 represents unsuitable habitat. The verbal or mathematical rules by which an HSI is assigned to an area are called an HSI model. A series of Habitat Suitability Index (HSI) models, described by Schamberger et al. (1982), have been published to assist users in applying HEP. HSI model building approaches are described in U.S. Fish and Wildlife Service (1981). One type of HSI model described in detail requires the development of Suitability Index (SI) graphs for habitat variables believed to be important for the growth, survival, standing crop, or other measure of well-being for a species. Suitability indices range from 0 to 1.0, with 1.0 representing optimum conditions for the variable. When HSI models based on suitability indices are used, habitat variable values are measured, or estimated, and converted to SI's through the use of a Suitability Index graph for each variable. Individual SI's are aggregated into an HSI. Standard methods for testing this type of HSI model did not exist at the time the studies reported in this document were performed. A workshop was held in Fort Collins, Colorado, February 14-15, 1983, that brought together biologists experienced in the use, development, and testing of aquatic HSI models, in an effort to address the following objectives: (1) review the needs of HSI model users; (2) discuss and document the results of aquatic HSI model tests; and (3) provide recommendations for the future development, testing, modification, and use of HSI models. Individual presentations, group discussions, and group

Ketamine. A solution to procedural pain in burned children.

Science.gov (United States)

Groeneveld, A; Inkson, T

1992-09-01

Our experience has shown ketamine to be a safe and effective method of providing pain relief during specific procedures in burned children. It renders high doses of narcotics unnecessary and offers children the benefit of general anesthesia without the requirement of endotracheal intubation and a trip to the operating room. The response of parents and staff to the use of ketamine has been positive. Parents often experience feelings of guilt following injury to a child and are eager to employ methods that reduce their child's pain. So far, no parent has refused the administration of ketamine; some have even asked that it be used during subsequent procedures on their child. With adequate pre-procedure teaching, parents are prepared for the possible occurrence of emergent reactions and can assist in reorienting the child during recovery. Staff have found that the stress of doing painful procedures on children is reduced when ketamine is used. The procedures tend to be quicker and the predicament of working on a screaming, agitated child is eliminated. At the same time, nursing staff have had to get used to the nystagmic gaze of the children and accept that these patients are truly anesthetized even though they might move and talk. Despite the success we and others have had with ketamine, several questions about its use in burn patients remain unanswered. The literature does not answer such questions as: Which nursing measures reduce the incidence of emergent reactions? How many ketamine anesthetics can safely be administered to one individual? How does the frequency of administration relate to tolerance in a burn patient? Are there detrimental effects of frequent or long-term use? Clearly, an understanding of these questions is necessary to determine the safe boundaries of ketamine use in burn patients. Ketamine is not a panacea for the problem of pain in burned children. But it is one means of managing procedural pain, which is, after all, a significant clinical

Land use suitability screening for power plant sites in Maryland

International Nuclear Information System (INIS)

Dobson, J.E.

1975-01-01

Since 1974 Oak Ridge National Laboratory (ORNL) has been engaged in developing an automated procedure for land use suitability screening. The Nuclear Regulatory Commission has funded the project to aid in the selection of power plant sites in Maryland. Its purpose is to identify candidate areas from which specific candidate sites can be chosen for detailed analyses. The ORNL approach assures that certain key variables are examined empirically for every cell in the study region before candidate sites are selected. Each variable is assigned an importance weight and compatibility score based upon its effect on the economic, social, or ecologic costs associated with construction in a given cell. The weighted scores for each variable are aggregated and output as a suitability score for each cell

The stability of the strong gravity solution

International Nuclear Information System (INIS)

Baran, S.A.

1978-01-01

The perturbation of the classical solution to a strong gravity model given by Salam and Strathdee is investigated. Using the Hamiltonian formalism it is shown that this static and spherically symmetric solution is stable under the odd parity perturbations provided some parameters in the solution are suitably restricted

New interior solution describing relativistic fluid sphere

Indian Academy of Sciences (India)

Anewexact solution of embedding class I is presented for a relativistic anisotropicmassive fluid sphere. The new exact solution satisfies Karmarkar condition, is well-behaved in all respects, and therefore is suitable for the modelling of superdense stars. Consequently, using this solution, we have studied in detail two ...

Niche suitability affects development: skull asymmetry increases in less suitable areas.

Directory of Open Access Journals (Sweden)

Renan Maestri

Full Text Available For conservation purposes, it is important to take into account the suitability of a species to particular habitats; this information may predict the long-term survival of a species. In this sense, morphological measures of developmental stress, such as fluctuating asymmetry, can be proxies for an individual's performance in different regions. In this study, we conducted tests to determine whether areas with different levels of suitability for a species (generated by ecological niche models were congruent with morphological markers that reflect environmental stress and morphological variance. We generated a Maxent niche model and compared the suitability assessments of several areas with the skull morphology data (fluctuating asymmetry and morphological disparity of populations of the Atlantic forest endemic to Brazil rodent Akodon cursor. Our analyses showed a significant negative relationship between suitability levels and fluctuating asymmetry levels, which indicates that in less suitable areas, the individuals experience numerous disturbances during skull ontogeny. We have not found an association between morphological variance and environmental suitability. As expected, these results suggest that in environments with a lower suitability, developmental stress is increased. Such information is helpful in the understanding of the species evolution and in the selection of priority areas for the conservation of species.

SITE SUITABILITY ANALYSIS FOR BEEKEEPING VIA ANALYTHICAL HYREARCHY PROCESS, KONYA EXAMPLE

Directory of Open Access Journals (Sweden)

F. Sarı

2017-11-01

Full Text Available Over the past decade, the importance of the beekeeping activities has been emphasized in the field of biodiversity, ecosystems, agriculture and human health. Thus, efficient management and deciding correct beekeeping activities seems essential to maintain and improve productivity and efficiency. Due to this importance, considering the economic contributions to the rural area, the need for suitability analysis concept has been revealed. At this point, Multi Criteria Decision Analysis (MCDA and Geographical Information Systems (GIS integration provides efficient solutions to the complex structure of decision- making process for beekeeping activities. In this study, site suitability analysis via Analytical Hierarchy Process (AHP was carried out for Konya city in Turkey. Slope, elevation, aspect, distance to water resources, roads and settlements, precipitation and flora criteria are included to determine suitability. The requirements, expectations and limitations of beekeeping activities are specified with the participation of experts and stakeholders. The final suitability map were validated with existing 117 beekeeping locations and Turkish Statistical Institute 2016 beekeeping statistics for Konya province.

Guidelines for using the Delphi Technique to develop habitat suitability index curves

Science.gov (United States)

Crance, Johnie H.

1987-01-01

Habitat Suitability Index (SI) curves are one method of presenting species habitat suitability criteria. The curves are often used with the Habitat Evaluation Procedures (HEP) and are necessary components of the Instream Flow Incremental Methodology (IFIM) (Armour et al. 1984). Bovee (1986) described three categories of SI curves or habitat suitability criteria based on the procedures and data used to develop the criteria. Category I curves are based on professional judgment, with 1ittle or no empirical data. Both Category II (utilization criteria) and Category III (preference criteria) curves have as their source data collected at locations where target species are observed or collected. Having Category II and Category III curves for all species of concern would be ideal. In reality, no SI curves are available for many species, and SI curves that require intensive field sampling often cannot be developed under prevailing constraints on time and costs. One alternative under these circumstances is the development and interim use of SI curves based on expert opinion. The Delphi technique (Pill 1971; Delbecq et al. 1975; Linstone and Turoff 1975) is one method used for combining the knowledge and opinions of a group of experts. The purpose of this report is to describe how the Delphi technique may be used to develop expert-opinion-based SI curves.

Function Allocation in Complex Socio-Technical Systems: Procedure usage in nuclear power and the Context Analysis Method for Identifying Design Solutions (CAMIDS) Model

Science.gov (United States)

Schmitt, Kara Anne

This research aims to prove that strict adherence to procedures and rigid compliance to process in the US Nuclear Industry may not prevent incidents or increase safety. According to the Institute of Nuclear Power Operations, the nuclear power industry has seen a recent rise in events, and this research claims that a contributing factor to this rise is organizational, cultural, and based on peoples overreliance on procedures and policy. Understanding the proper balance of function allocation, automation and human decision-making is imperative to creating a nuclear power plant that is safe, efficient, and reliable. This research claims that new generations of operators are less engaged and thinking because they have been instructed to follow procedures to a fault. According to operators, they were once to know the plant and its interrelations, but organizationally more importance is now put on following procedure and policy. Literature reviews were performed, experts were questioned, and a model for context analysis was developed. The Context Analysis Method for Identifying Design Solutions (CAMIDS) Model was created, verified and validated through both peer review and application in real world scenarios in active nuclear power plant simulators. These experiments supported the claim that strict adherence and rigid compliance to procedures may not increase safety by studying the industry's propensity for following incorrect procedures, and when it directly affects the outcome of safety or security of the plant. The findings of this research indicate that the younger generations of operators rely highly on procedures, and the organizational pressures of required compliance to procedures may lead to incidents within the plant because operators feel pressured into following the rules and policy above performing the correct actions in a timely manner. The findings support computer based procedures, efficient alarm systems, and skill of the craft matrices. The solution to

Comparison of Prime Movers Suitable for USMC Expeditionary Power Sources

Energy Technology Data Exchange (ETDEWEB)

Theiss, T J; Conklin, J. C.; Thomas, John F.; Armstrong, T. R.

2000-04-18

This report documents the results of the ORNL investigation into prime movers that would be desirable for the construction of a power system suitable for the United States Marine Corps (USMC) expeditionary forces under Operational Maneuvers From The Sea (OMFTS) doctrine. Discrete power levels of {approx}1, 5, 15, and 30 kW are considered. The only requirement is that the prime mover consumes diesel fuel. A brief description is given for the prime movers to describe their basic scientific foundations and relative advantages and disadvantages. A list of key attributes developed by ORNL has been weighted by the USMC to indicate the level of importance. A total of 14 different prime movers were scored by ORNL personnel in four size ranges (1,5, 15, & 30 kW) for their relative strength in each attribute area. The resulting weighted analysis was used to indicate which prime movers are likely to be suitable for USMC needs. No single engine or prime mover emerged as the clear-cut favorite but several engines scored as well or better than the diesel engine. At the higher load levels (15 & 30 kW), the results indicate that the open Brayton (gas turbine) is a relatively mature technology and likely a suitable choice to meet USMC needs. At the lower power levels, the situation is more difficult and the market alone is not likely to provide an optimum solution in the time frame desired (2010). Several prime movers should be considered for future developments and may be satisfactory; specifically, the Atkinson cycle, the open Brayton cycle (gas turbine), the 2-stroke diesel. The rotary diesel and the solid oxide fuel cell should be backup candidates. Of all these prime movers, the Atkinson cycle may well be the most suitable for this application but is an immature technology. Additional demonstrations of this engine will be conducted at ORNL. If this analysis is positive, then the performance of a generator set using this engine, the open Brayton and the 2-stroke diesel should

Which Introductory Programming Approach Is Most Suitable for Students: Procedural or Visual Programming?

Science.gov (United States)

Eid, Chaker; Millham, Richard

2012-01-01

In this paper, we discuss the visual programming approach to teaching introductory programming courses and then compare this approach with that of procedural programming. The involved cognitive levels of students, as beginning students are introduced to different types of programming concepts, are correlated to the learning processes of…

Matching procedure for the sixth Painleve equation

International Nuclear Information System (INIS)

Guzzetti, Davide

2006-01-01

In the framework of the isomonodromy deformation method, we present a constructive procedure to obtain the critical behaviour of Painleve VI transcendents and solve the connection problem. This procedure yields two- and one-parameter families of solutions, including trigonometric and logarithmic behaviours, and three classes of solutions with Taylor expansion at a critical point

Monazite as a suitable actinide waste form

Energy Technology Data Exchange (ETDEWEB)

Schlenz, Hartmut; Heuser, Julia; Schmitz, Stephan; Bosbach, Dirk [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Energie und Klimaforschung (IEK), Nukleare Entsorgung und Reaktorsicherheit (IEK-6); Neumann, Andreas [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Energie und Klimaforschung (IEK), Nukleare Entsorgung und Reaktorsicherheit (IEK-6); RWTH Aachen Univ. (Germany). Inst. for Crystallography

2013-03-01

The conditioning of radioactive waste from nuclear power plants and in some countries even of weapons plutonium is an important issue for science and society. Therefore the research on appropriate matrices for the immobilization of fission products and actinides is of great interest. Beyond the widely used borosilicate glasses, ceramics are promising materials for the conditioning of actinides like U, Np, Pu, Am, and Cm. Monazite-type ceramics with general composition LnPO{sub 4} (Ln = La to Gd) and solid solutions of monazite with cheralite or huttonite represent important materials in this field. Monazite appears to be a promising candidate material, especially because of its outstanding properties regarding radiation resistance and chemical durability. This article summarizes the most recent results concerning the characterization of monazite and respective solid solutions and the study of their chemical, thermal, physical and structural properties. The aim is to demonstrate the suitability of monazite as a secure and reliable waste form for actinides. (orig.)

Scientific Approach and Inquiry Learning Model in the Topic of Buffer Solution: A Content Analysis

Science.gov (United States)

Kusumaningrum, I. A.; Ashadi, A.; Indriyanti, N. Y.

2017-09-01

Many concepts in buffer solution cause student’s misconception. Understanding science concepts should apply the scientific approach. One of learning models which is suitable with this approach is inquiry. Content analysis was used to determine textbook compatibility with scientific approach and inquiry learning model in the concept of buffer solution. By using scientific indicator tools (SIT) and Inquiry indicator tools (IIT), we analyzed three chemistry textbooks grade 11 of senior high school labeled as P, Q, and R. We described how textbook compatibility with scientific approach and inquiry learning model in the concept of buffer solution. The results show that textbook P and Q were very poor and book R was sufficient because the textbook still in procedural level. Chemistry textbooks used at school are needed to be improved in term of scientific approach and inquiry learning model. The result of these analyses might be of interest in order to write future potential textbooks.

Numeric E.I.A.`s techniques to determine suitable sites for solid waste sanitary plants; Tecniche numeriche di V.I.A. per l`individuazione dei siti idonei alla localizzazione di impianti di smaltimento dei rifiuti solidi

Energy Technology Data Exchange (ETDEWEB)

Valentini, A.

1997-07-01

A standard procedure for choosing suitable sites for the localization of waste treatment and disposal plants is the main step for a correct sanitary program. Two are the principal difficulties: to define a correct group of criteria, excluding and limiting conditions to be applied in the E.I.A.`s techniques: to employ a simplified and flexible methodology that permits to obtain a suitable sites hierarchy. An E.I.A.`s methodology is proposed, distinguished in three numeric techniques with different complexity. Beside, to limit the subjectiveness of the user`s judgement, two solutions are applied, i.e., a method to define the impact factors of the Plant system and a sensitivity test be applied on the importance range of values. =

A Feasibility study of remote consultation to determine suitability for surgery in stroke rehabilitation

NARCIS (Netherlands)

Buurke, Jaap; Kleissen, R.F.M.; Nene, A.V.; Bloo, J.K.C.; Renzenbrink, G.J.; Zeegers, A.V.C.M.; Doederlein, L.; Hermens, Hermanus J.

2004-01-01

We studied knowledge transfer for the determination of the suitability of stroke patients for a specialist surgical procedure (split anterior tibial tendon transfer). Gait analysis data from patients at a general hospital were discussed with an expert in another country using personal computers, an

Solution Tree Problem Solving Procedure for Engineering Analysis ...

African Journals Online (AJOL)

Illustrations are provided in the thermofluid engineering area to showcase the procedure's applications. This approach has proved to be a veritable tool for enhancing the problem-solving and computer algorithmic skills of engineering students, eliciting their curiosity, active participation and appreciation of the taught course.

Experiences in the management of technical competencies and suitability of qualified experts

International Nuclear Information System (INIS)

Smith, David M.

2008-01-01

The UK Defence Science and Technology Laboratory (Dstl) RPA Body was established to provide radiation protection advice to the UK Ministry of Defence and other UK Government organisations. It consists of around 20 individually certificated Qualified Experts (known as Radiation Protection Advisers (RPA) in the terminology of UK legislation) 15 health physicists (HP), and other support staff. The RPA Body operates to procedures that satisfy the requirements of the UK Heath and Safety Executive (HSE) (the primary regulator in the UK for radiation protection legislation) and as such is recognised by the HSE as an RPA Body. Individual RPAs, HPs and support staff are only appointed to the RPA Body when they are deemed suitable and can satisfy the various general and specific operational roles within the Body. The criteria and procedures for establishing suitability of a candidate to a role are described. In addition to the basic underpinning knowledge for RPAs (the equivalent of the 'qualified expert' defined in Article 1 of the Basic Safety Standards Directive 96/29/EURATOM, candidates for appointment to the RPA Body are required to demonstrate competence and suitability in specialist areas as determined by the business needs of Dstl RPA Body. The criteria and assessment processes are described. The technical management of the RPA Body is illustrated, stressing the importance of the selection and allocation of suitable individuals to specific tasks, using a competency matrix. Experience to date with the RPA Body processes has been very positive; the arrangements are sufficiently flexible such as to accommodate the changing legislative requirements and the business needs of the RPA Body. There are many additional benefits arising to Dstl and its customers as a result of operation as an RPA Body. (author)

Preliminary geological suitability assessment for LILW disposal

International Nuclear Information System (INIS)

Tomse, P.; Mele, I.

2001-01-01

Due to the growing need for a final disposal of LILW, the final solution for the short-lived LILW is the key issue of radioactive waste management in Slovenia at the moment. ARAO - the Slovenian Agency for Radwaste Management - is intensely involved in the re-initiated site selection process for a LILW repository. In this new process we are trying to combine as best as possible the technical, geologically-led and the advocacy-site selection processes. By a combination of technical and volunteer approach to the site selection we wish to guarantee high public involvement and sufficient flexibility of the process to adapt to specific conditions or new circumstances while the project is ongoing. In the technical phase, our tendency is to retain a larger number of potential areas/sites. We also keep open the possibility of choosing the type of repository. The decision between the surface and underground option will be made only once the site has been defined. In accordance with the IAEA recommendations the site selection process is divided into four stages: the conceptual and planning stage, area survey stage, site characterisation stage and site confirmation stage. Last year the area survey stage was started. In the preliminary geological suitability assessment the required natural predisposition of Slovene territory was assessed in order to locate geologically suitable formations. The assessment of natural conditions of the system was based on consideration of the main geological, hydro-geological and seismotectonic conditions. It was performed with ARC/INFO technology. The results are compiled in a map, showing potential areas for underground and surface disposal of LILW in Slovenia. It has been established that there is a potential suitability for both surface and underground disposal on about 10 000 km 2 of the Slovenian territory, which represents almost half of the entire Slovenian territory. These preliminary results are now being carefully re-examined. As an

Test procedure for anion exchange testing with Argonne 10-L solutions

International Nuclear Information System (INIS)

Compton, J.A.

1995-01-01

Four anion exchange resins will be tested to confirm that they will sorb and release plutonium from/to the appropriate solutions in the presence of other cations. Certain cations need to be removed from the test solutions to minimize adverse behavior in other processing equipment. The ion exchange resins will be tested using old laboratory solutions from Argonne National Laboratory; results will be compared to results from other similar processes for application to all plutonium solutions stored in the Plutonium Finishing Plant

A new procedure for extraction of collagen from modern and archaeological bones for 14C dating.

Science.gov (United States)

Maspero, F; Sala, S; Fedi, M E; Martini, M; Papagni, A

2011-10-01

Bones are potentially the best age indicators in a stratigraphic study, because they are closely related to the layer in which they are found. Collagen is the most suitable fraction and is the material normally used in radiocarbon dating. Bone contaminants can strongly alter the carbon isotopic fraction values of the samples, so chemical pretreatment for (14)C dating by accelerator mass spectrometry (AMS) is essential. The most widespread method for collagen extraction is based on the Longin procedure, which consists in HCl demineralization to dissolve the inorganic phase of the samples, followed by dissolution of collagen in a weak acid solution. In this work the possible side effects of this procedure on a modern bone are presented; the extracted collagen was analyzed by ATR-IR spectroscopy. An alternative procedure, based on use of HF instead of HCl, to minimize unwanted degradation of the organic fraction, is also given. A study by ATR-IR spectroscopic analysis of collagen collected after different demineralization times and with different acid volumes, and a study of an archaeological sample, are also presented.

Evaluation of sedation for standing clinical procedures in horses using detomidine combined with buprenorphine.

Science.gov (United States)

Taylor, Polly; Coumbe, Karen; Henson, Frances; Scott, David; Taylor, Alan

2014-01-01

To examine the effect of including buprenorphine with detomidine for sedation of horses undergoing clinical procedures. Partially blinded, randomised, prospective clinical field trial. Eighty four client-owned horses scheduled for minor surgery or diagnostic investigation under standing sedation. The effects of buprenorphine (5 μg kg(-1) ) (Group B, n = 46) or placebo (5% glucose solution) (Group C, n = 38) in combination with detomidine (10 μg kg(-1) ) were compared in standing horses undergoing minor clinical procedures. The primary outcome measure was successful completion of the procedure. The degree of sedation and ataxia were scored using simple descriptive scales. Heart and respiratory rates were recorded at 15-30 minute intervals. Parametric data from each group were compared using anova or t-test and non parametric data using the Mann-Whitney U test. The procedure was carried out successfully in 91% of Group B and 63% of Group C (p detomidine, increased after buprenorphine but not glucose administration, was more profound in group B and lasted longer (60 versus 30 minutes) p detomidine 10 and 20 μg kg(-1) with minor side effects similar to other alpha2 agonist/opioid combinations. Detomidine-buprenorphine sedation is suitable for standing procedures in horses. © 2013 Association of Veterinary Anaesthetists and the American College of Veterinary Anesthesia and Analgesia.

Acid solution is a suitable medium for introducing QX-314 into nociceptors through TRPV1 channels to produce sensory-specific analgesic effects.

Directory of Open Access Journals (Sweden)

He Liu

sciatic nerve selectively blocked the sensory but not the motor functions in naïve and CCI mice. CONCLUSIONS/SIGNIFICANCE: Acid solution is a suitable medium for introducing QX-314 into nociceptors through TRPV1 channels to produce a sensory-specific analgesic effect.

Development of an electrochemical 90Sr-90Y generator for separation of 90Y suitable for targeted therapy

International Nuclear Information System (INIS)

Chakravarty, Rubel; Pandey, Usha; Manolkar, Remani B.; Dash, Ashutosh; Venkatesh, Meera; Pillai, M.R. Ambikalmajan

2008-01-01

90 Y of high specific activity and very high radionuclidic purity (>99.998%) is essential for targeted therapy. Since the current methods used for the preparation of 90 Y from 90 Sr are not adaptable for use in a central/hospital radiopharmacy, a simple 90 Sr- 90 Y generator system based on electrochemical separation technique was developed. Methods: Two-cycle electrolysis procedure was developed for separation of 90 Y from 90 Sr in nitrate solution. The first electrolysis was performed for 90 min in 90 Sr(NO 3 ) 2 feed solution at pH 2-3 at a potential of -2.5V with 100-200 mA current using platinum electrodes. The second electrolysis was performed for 45 min in 3 mM HNO 3 at a potential of -2.5V with 100 mA current. In this step, the cathode from the first electrolysis containing 90 Y was used as anode along with a fresh circular platinum electrode as cathode. The 90 Y deposited on the circular cathode after the second electrolysis was dissolved in acetate buffer to obtain 90 Y acetate, suitable for radiolabeling. Results: >96% recovery of 90 Y could be achieved in each cycle, with an overall decay corrected yield of >90%. The recovered 90 Y had high radionuclidic purity with barely 30.2±15.2 kBq (817±411 nCi) of 90 Sr per 37 GBq (1 Ci) of 90 Y (0.817±0.411 ppm). Consistent and repeated separation could be demonstrated using up to 1.85 GBq (50 mCi) of 90 Sr. The generator was named 'Kamadhenu,' the eternally milk-yielding Indian mythological cow. Conclusions: A technique suitable for adaptation at central radiopharmacies for obtaining therapeutic quantities of pure 90 Y has been developed

Soft-solution route to ZnO nanowall array with low threshold power density

Science.gov (United States)

Jang, Eue-Soon; Chen, Xiaoyuan; Won, Jung-Hee; Chung, Jae-Hun; Jang, Du-Jeon; Kim, Young-Woon; Choy, Jin-Ho

2010-07-01

ZnO nanowall array (ZNWA) has been directionally grown on the buffer layer of ZnO nanoparticles dip-coated on Si-wafer under a soft solution process. Nanowalls on substrate are in most suitable shape and orientation not only as an optical trap but also as an optical waveguide due to their unique growth habit, V[011¯0]≫V[0001]≈V[0001¯]. Consequently, the stimulated emission at 384 nm through nanowalls is generated by the threshold power density of only 25 kW/cm2. Such UV lasing properties are superior to those of previously reported ZnO nanorod arrays. Moreover, there is no green (defect) emission due to the mild procedure to synthesize ZNWA.

Investigation on Suitability of Natural Fibre as Replacement Material for Table Tennis Blade

Science.gov (United States)

Arifin, A. M. T.; Fahrul Hassan, M.; Ismail, A. E.; Zulafif Rahim, M.; Rasidi Ibrahim, M.; Haq, R. H. Abdul; Rahman, M. N. A.; Yunos, M. Z.; Amin, M. H. M.

2017-08-01

This paper presents an investigation of suitability natural fibre as replacement material for table tennis blade, due to low cost, lightweight and apparently environmentally. Nowadays, natural fibre are one of the materials often used in replaced the main material on manufacturing sector, such as automotive, and construction. The objective of this study is to investigate and evaluate the suitability natural fiber materials to replace wood as a structure on table tennis blade. The mechanical properties of the different natural fibre material were examined, and correlated with characteristic of table tennis blade. The natural fibre selected for the study are kenaf (Hibiscus Cannabinus), jute, hemp, sisal (Agave Sisalana) and ramie. A further comparison was made with the corresponding properties of each type of natural fiber using Quality Function Deployment (QFD) and Theory of Inventive Problem Solving (TRIZ). TRIZ has been used to determine the most appropriate solution in producing table tennis blade. The results showed the most appropriate solution in producing table tennis blade using natural fibre is kenaf natural fibre. The selected on suitability natural fibre used as main structure on table tennis blade are based on the characteristics need for good performance of table tennis blade, such as energy absorption, lightweight, strength and hardness. Therefore, it shows an opportunity for replacing existing materials with a higher strength, lower cost alternative that is environmentally friendly.

A new procedure for extraction of collagen from modern and archaeological bones for {sup 14}C dating

Energy Technology Data Exchange (ETDEWEB)

Maspero, F. [CUDaM, University of Milano Bicocca, Milano (Italy); Sala, S.; Papagni, A. [University of Milano Bicocca, Materials Science Department, Milano (Italy); Fedi, M.E. [INFN sezione di Firenze, Sesto Fiorentino (Firenze) (Italy); Martini, M. [CUDaM, University of Milano Bicocca, Milano (Italy); University of Milano Bicocca, Materials Science Department, Milano (Italy); INFN sezione di Milano Bicocca, Milano (Italy)

2011-10-15

Bones are potentially the best age indicators in a stratigraphic study, because they are closely related to the layer in which they are found. Collagen is the most suitable fraction and is the material normally used in radiocarbon dating. Bone contaminants can strongly alter the carbon isotopic fraction values of the samples, so chemical pretreatment for {sup 14} C dating by accelerator mass spectrometry (AMS) is essential. The most widespread method for collagen extraction is based on the Longin procedure, which consists in HCl demineralization to dissolve the inorganic phase of the samples, followed by dissolution of collagen in a weak acid solution. In this work the possible side effects of this procedure on a modern bone are presented; the extracted collagen was analyzed by ATR-IR spectroscopy. An alternative procedure, based on use of HF instead of HCl, to minimize unwanted degradation of the organic fraction, is also given. A study by ATR-IR spectroscopic analysis of collagen collected after different demineralization times and with different acid volumes, and a study of an archaeological sample, are also presented. (orig.)

Waste disposal process on the basis of fission product solutions, and suitable plant

International Nuclear Information System (INIS)

Thiele, D.

1984-01-01

The nitrous fission product solution containing ruthenium is concentrated in a wiper blade evaporator. After intermediate drying the residue is vitrified adding vitrifying agents and NH4 in an amount of 20 to 300% referred to the nitrate content of the concentrated residue. (orig./PW)

CONCORDAT PROCEDURE. LEGISLATIVE AND JURISPRUDENTIAL HIGHLIGHTS

Directory of Open Access Journals (Sweden)

Mihaela Tofan

2014-11-01

Full Text Available Insolvency Code has revived theoreticians’ and practitioners’ discussions, equally. The voluntary arrangements procedure is considered a legal solution for the prevention and recovery from commercial actors’ financial difficulty. The current legal framework establishes a number of imperative conditions for the implementation of this procedure, but in many cases, the application of the current regulation generated different conclusions. In less than half a year, since the entry into force of the law, the practice for each court varied. The paper synthesizes separate opinions and proposes solutions for shaping a more precise legal framework.

Suitability of various materials for porous filters in diffusion experiments

Energy Technology Data Exchange (ETDEWEB)

Aldaba, David; Vidal, Miquel; Rigol, Anna [Univ. de Barcelona (Spain). Dept. de Quimica Analitica; Glaus, Martin; Van Loon, Luc [Paul Scherrer Institut, Villigen PSI (Switzerland). Lab. for Waste Management; Leupin, Olivier [Nagra, Wettingen (Switzerland)

2014-10-01

The suitability of different porous materials (stainless steel, VYCOR {sup registered} glass, Al{sub 2}O{sub 3} and PEEK) for use as confining filters in diffusion experiments was evaluated by measuring the effective diffusion coefficients (D{sub e}) of neutral (HTO) and ionic solutes (Na{sup +}, Cs{sup +}, Sr{sup 2+}, Cl{sup -}, SeO{sub 4}{sup 2-}) in the materials in through-diffusion experiments. For stainless steel filters, the D{sub e} values of the target solutes correlated satisfactorily with their bulk diffusion coefficient in water (D{sub w}); thus, the diffusion process in the stainless steel filters was primarily controlled by the diffusivity of the solvated ions. For the remaining materials, the D{sub e} and D{sub w} values were also correlated for the target solutes, and the geometric factors were in the sequence: VYCOR {sup registered} glass < Al{sub 2}O{sub 3} < PEEK. Stainless steel and VYCOR {sup registered} glass were the most appropriate materials because of their high D{sub e} values, but a specific interaction of caesium with VYCOR {sup registered} glass was hypothesised because the D{sub e} values obtained for this solute were slightly higher than expected.

Agroforestry suitability analysis based upon nutrient availability mapping: a GIS based suitability mapping

Directory of Open Access Journals (Sweden)

Firoz Ahmad

2017-05-01

Full Text Available Agroforestry has drawn the attention of researchers due to its capacity to reduce the poverty and land degradation, improve food security and mitigate the climate change. However, the progress in promoting agroforestry is held back due to the lack of reliable data sets and appropriate tools to accurately map and to have an adequate decision making system for agroforestry modules. Agroforestry suitability being one special form of land suitability is very pertinent to study in the current times when there is tremendous pressure on the land as it is a limited commodity. The study aims for applying the geo-spatial tools towards visualizing various soil and environmental data to reveal the trends and interrelationships and to achieve a nutrient availability and agroforestry suitability map. Using weight matrix and ranks, individual maps were developed in ArcGIS 10.1 platform to generate nutrient availability map, which was later used to develop agroforestry suitability map. Watersheds were delineated using DEM in some part of the study area and were evaluated for prioritizing it and agroforestry suitability of the watersheds were also done as per the schematic flowchart. Agroforestry suitability regions were delineated based upon the weight and ranks by integrated mapping. The total open area was identified 42.4% out of which 21.6% area was found to have high suitability towards agroforestry. Within the watersheds, 22 village points were generated for creating buffers, which were further evaluated showing its proximity to high suitable agroforestry sites thus generating tremendous opportunity to the villagers to carry out agroforestry projects locally. This research shows the capability of remote sensing in studying agroforestry practices and in estimating the prominent factors for its optimal productivity. The ongoing agroforestry projects can be potentially diverted in the areas of high suitability as an extension. The use of ancillary data in GIS

Development of a specific methodology to assess suitable sites to receive a repository for L/ILW waste in the Portuguese territory

Energy Technology Data Exchange (ETDEWEB)

Paiva, Isabel [Instituto Superior Tecnico, Nuclear and Technological Campus, Technical, University of Lisbon, Estrada Nacional N10 - km 139,7, 2695-066, Bobadela LRS (Portugal); Trindade, Romao B. [MedicalConsult,S.A., Campo Grande, no. 56, 8A, 1700-093, Lisboa (Portugal); Goncalves, Mario A. [University of Lisbon, Faculty of Sciences, Dept. Geology and CREMINER-ISR/LA, Ed. C6, 4, 1749-016 Lisbon (Portugal); Mateus, Antonio [University of Lisbon, Faculty of Sciences, Dept. Geology and CeGUL, Ed. C6, 4, 1749-016 Lisbon (Portugal)

2013-07-01

Portugal does not have nuclear power plants but records an increasing production of radioactive waste from medical, industrial and research applications of radioactive materials in the form of sealed and unsealed sources; the country totals include also the spent fuel of one nuclear reactor for research purposes. Since radioactive waste management policies and practices in Portugal will have to comply with the Council Directive 2011/70/Euratom and the IAEA Joint Convention, the search for scientific and technological solutions to deal with radioactive wastes produced in the country started some years ago. The research carried out recently under the scope of a national funded project (KADRWaste, PTDC/CTEGEX/ 82678/2006) represents a firm step in this commitment. Indeed, the transfer of methodologies tested and validated in this project allowed for improvement to a procedure to assess suitable sites to receive a near-surface repository for 'Low and Intermediate Level Waste, Short Live and Long Live' (LILWSL, LL) wastes in Portugal mainland. Although the main stages of the procedure can be of universal usage, details were designed according to the intrinsic geological, geomorphic and meteorological features of previously selected target-areas. All the requirements exhaustively listed in many reports of the IAEA were fulfilled and, in addition, the application of mineralogical, geochemical and textural criteria is strongly advised. The proposed procedure is based on a 5 key-steps approach preceded by clarification of the boundary conditions to be imposed, which are crucial to the inventory of various compulsory technical requirements. This analysis requires the adoption of stringent criteria, many of them of multidisciplinary nature, including tests of vulnerability and assessment of uncertainty, besides the environmental impact risk. As a result, priority targets that are not excluded will integrate different classes and, depending on the existing knowledge

Development of a specific methodology to assess suitable sites to receive a repository for L/ILW waste in the Portuguese territory

International Nuclear Information System (INIS)

Paiva, Isabel; Trindade, Romao B.; Goncalves, Mario A.; Mateus, Antonio

2013-01-01

Portugal does not have nuclear power plants but records an increasing production of radioactive waste from medical, industrial and research applications of radioactive materials in the form of sealed and unsealed sources; the country totals include also the spent fuel of one nuclear reactor for research purposes. Since radioactive waste management policies and practices in Portugal will have to comply with the Council Directive 2011/70/Euratom and the IAEA Joint Convention, the search for scientific and technological solutions to deal with radioactive wastes produced in the country started some years ago. The research carried out recently under the scope of a national funded project (KADRWaste, PTDC/CTEGEX/ 82678/2006) represents a firm step in this commitment. Indeed, the transfer of methodologies tested and validated in this project allowed for improvement to a procedure to assess suitable sites to receive a near-surface repository for 'Low and Intermediate Level Waste, Short Live and Long Live' (LILWSL, LL) wastes in Portugal mainland. Although the main stages of the procedure can be of universal usage, details were designed according to the intrinsic geological, geomorphic and meteorological features of previously selected target-areas. All the requirements exhaustively listed in many reports of the IAEA were fulfilled and, in addition, the application of mineralogical, geochemical and textural criteria is strongly advised. The proposed procedure is based on a 5 key-steps approach preceded by clarification of the boundary conditions to be imposed, which are crucial to the inventory of various compulsory technical requirements. This analysis requires the adoption of stringent criteria, many of them of multidisciplinary nature, including tests of vulnerability and assessment of uncertainty, besides the environmental impact risk. As a result, priority targets that are not excluded will integrate different classes and, depending on the existing knowledge

Analytical solutions for tomato peeling with combined heat flux and convective boundary conditions

Science.gov (United States)

Cuccurullo, G.; Giordano, L.; Metallo, A.

2017-11-01

Peeling of tomatoes by radiative heating is a valid alternative to steam or lye, which are expensive and pollutant methods. Suitable energy densities are required in order to realize short time operations, thus involving only a thin layer under the tomato surface. This paper aims to predict the temperature field in rotating tomatoes exposed to the source irradiation. Therefore, a 1D unsteady analytical model is presented, which involves a semi-infinite slab subjected to time dependent heating while convective heat transfer takes place on the exposed surface. In order to account for the tomato rotation, the heat source is described as the positive half-wave of a sinusoidal function. The problem being linear, the solution is derived following the Laplace Transform Method. In addition, an easy-to-handle solution for the problem at hand is presented, which assumes a differentiable function for approximating the source while neglecting convective cooling, the latter contribution turning out to be negligible for the context at hand. A satisfying agreement between the two analytical solutions is found, therefore, an easy procedure for a proper design of the dry heating system can be set up avoiding the use of numerical simulations.

Procedure for marking, encryption, labelling and optical coding

OpenAIRE

Barranco, Ángel; Rodríguez-González, Agustín; Sánchez Valencia, Juan Ramón; Aparicio, Francisco J.; Blaszczyk-Lezak, Iwona Krystina; Holgado Bolaños, Miguel; Casquel del Campo, Rafael; Ocaña, J. L.; Molpeceres, C.; García-Ballesteros Ramírez, Juan José; Morales Furió, Miguel

2009-01-01

[EN] It permits marking or recording motifs (301) on surfaces whereon there has been deposited previously a fluorescent polymer layer (300) through a procedure of plasma polymerisation (100) of molecules of a colourant. The procedure combines the special characteristics of the polymer layers making them suitable for being capable of recording diverse motifs (301) thereon, and the possibility of recording by laser (10 1) or other techniques. Among such characteristics s...

Power Series Solution to the Pendulum Equation

Science.gov (United States)

Benacka, Jan

2009-01-01

This note gives a power series solution to the pendulum equation that enables to investigate the system in an analytical way only, i.e. to avoid numeric methods. A method of determining the number of the terms for getting a required relative error is presented that uses bigger and lesser geometric series. The solution is suitable for modelling the…

Efficient Reanalysis Procedures in Structural Topology Optimization

DEFF Research Database (Denmark)

Amir, Oded

This thesis examines efficient solution procedures for the structural analysis problem within topology optimization. The research is motivated by the observation that when the nested approach to structural optimization is applied, most of the computational effort is invested in repeated solutions...... on approximate reanalysis. For cases where memory limitations require the utilization of iterative equation solvers, we suggest efficient procedures based on alternative termination criteria for such solvers. These approaches are tested on two- and three-dimensional topology optimization problems including...

Development and verification of symptom based emergency procedure support system

International Nuclear Information System (INIS)

Saijou, Nobuyuki; Sakuma, Akira; Takizawa, Yoji; Tamagawa, Naoko; Kubota, Ryuji; Satou, Hiroyuki; Ikeda, Koji; Taminami, Tatsuya

1998-01-01

A Computerized Emergency Procedure Guideline (EPG) Support System has been developed for BWR and evaluated using training simulator. It aims to enhance the effective utilization of EPG. The system identifies suitable symptom-based operating procedures for present plant status automatically. It has two functions : one is plant status identification function, and the other is man-machine interface function. For the realization of the former function, a method which identifies and prioritize suitable symptom-based operational procedures against present plant status has been developed. As man-machine interface, operation flow chart display has been developed. It express the flow of the identified operating procedures graphically. For easy understanding of the display, important information such as plant status change, priority of operating procedures and completion/uncompletion of the operation is displayed on the operation flow display by different colors. As evaluation test, the response of the system to the design based accidents was evaluated by actual plant operators, using training simulator at BWR Training Center. Through the analysis of interviews and questionnaires to operators, it was shown that the system is effective and can be utilized for a real plant. (author)

EMP protection procedure for electrical/electronic systems

International Nuclear Information System (INIS)

Latorre, V.R.

1976-01-01

This paper presents a procedure for the protection engineer to follow in assessing a system with respect to its susceptibility to an electromagnetic pulse (EMP), and in determining whether the system requires protection. If the system is determined to be vulnerable to EMP, the procedure also indicates how to decide upon the most suitable protection scheme. The discussion centers on two flow charts, which illustrate the step-by-step procedure which utilizes the necessary ingredients of EMP protection engineering discussed in a previous paper. The description of the protection procedure is divided into two parts: the first dealing with issues on the macroscopic or large-scale system level, while the second is concerned with operations on the subsystem level or lower

Investigations of the sorption of cesium from acid solutions by various inorganic sorbents

International Nuclear Information System (INIS)

Suess, M.; Pfrepper, G.

1981-01-01

Studies have been made to investigate the suitability of various inorganic sorbents for separating and obtaining cesium from acid solutions. In greater details, the distribution coefficients of cesium from nitric acid and ammonium nitrate solution were determined. To determine the saturation capacities it was necessary to plot the isotherms of adsorption from 0.5 N and 3.1 N nitric acid. Experimental sorption from a model solution, of which the composition was equal to that of the liquid Purex waste, enabled the suitability of the various exchangers for obtaining cesium from fission product solutions to be determined. From the results obtained it is apparent that ammonium phosphomolybdate is best suited for obtaining cesium from acid fission product solutions. (orig.)

Aqueous Solution Chemistry of Plutonium

Energy Technology Data Exchange (ETDEWEB)

Clark, David L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-01-28

Things I have learned working with plutonium: Chemistry of plutonium is complex; Redox equilibria make Pu solution chemistry particularly challenging in the absence of complexing ligands; Understanding this behavior is key to successful Pu chemistry experiments; There is no suitable chemical analog for plutonium.

[Painful procedures in small ruminants - castration of rams and bucks. - An overview].

Science.gov (United States)

Bauer, Benjamin; Hannemann, Regina; Lendl, Christine; Strobel, Heinz; Ganter, Martin

2018-04-01

The castration of farm animals is practiced routinely throughout the world and the procedure is subject to different levels of regulation in different countries. In Germany, painful procedures in animals are regulated by the animal welfare act. However, the indications for acceptable methods of lamb and kid castration are still under discussion. There are distinct differences between the theoretical requirements of this legislation and experiences in practice. When male lambs are kept for many months with their dams, or with ewe lambs, castration is essential to avoid unwanted pregnancies and the slaughter of pregnant females. In the opinion of the authors, it is essential that castration of small ruminants must remain possible. However, the methods used for these painful procedures need to be reassessed and if necessary new regulations established. When castration is necessary, sufficient anaesthesia and analgesia must be used irrespective of species, age and method. To make this possible potent anaesthetics and analgesics urgently need to be licensed for use in these species. This would provide an evidence base for their use and extricate veterinary practitioners from the need to use the cascade system with its associated liabilities. Current literature has been reviewed here and possible new approaches discussed in order to establish solutions that are suitable for the animals, their keepers and veterinarians. Schattauer GmbH.

Existence of extremal periodic solutions for quasilinear parabolic equations

Directory of Open Access Journals (Sweden)

Siegfried Carl

1997-01-01

bounded domain under periodic Dirichlet boundary conditions. Our main goal is to prove the existence of extremal solutions among all solutions lying in a sector formed by appropriately defined upper and lower solutions. The main tools used in the proof of our result are recently obtained abstract results on nonlinear evolution equations, comparison and truncation techniques and suitably constructed special testfunction.

Effects of solution volume on hydrogen production by pulsed spark discharge in ethanol solution

Energy Technology Data Exchange (ETDEWEB)

Xin, Y. B.; Sun, B., E-mail: sunb88@dlmu.edu.cn; Zhu, X. M.; Yan, Z. Y.; Liu, H.; Liu, Y. J. [College of Environmental Science and Engineering, Dalian Maritime University, Dalian 116026 (China)

2016-07-15

Hydrogen production from ethanol solution (ethanol/water) by pulsed spark discharge was optimized by varying the volume of ethanol solution (liquid volume). Hydrogen yield was initially increased and then decreased with the increase in solution volume, which achieved 1.5 l/min with a solution volume of 500 ml. The characteristics of pulsed spark discharge were studied in this work; the results showed that the intensity of peak current, the rate of current rise, and energy efficiency of hydrogen production can be changed by varying the volume of ethanol solution. Meanwhile, the mechanism analysis of hydrogen production was accomplished by monitoring the process of hydrogen production and the state of free radicals. The analysis showed that decreasing the retention time of gas production and properly increasing the volume of ethanol solution can enhance the hydrogen yield. Through this research, a high-yield and large-scale method of hydrogen production can be achieved, which is more suitable for industrial application.

Assessment of the suitability of trees for brownfields reuse in the post-mining landscape

Science.gov (United States)

Mec, J.; Lokajickova, B.; Sotkova, N.; Svehlakova, H.; Stalmachova, B.

2017-10-01

The post-mining landscape of Upper Silesian is deterioration of the original landscape caused by underground coal mining. There are huge ecosystems changes, which have been reclaimed by nature-friendly procedures. The aim of the work is to evaluate the suitability of selected trees for reuse of brownfields in this landscape and proposals for reclamation in the interest areas of Upper Silesian.

Dynamical modeling procedure of a Li-ion battery pack suitable for real-time applications

International Nuclear Information System (INIS)

Castano, S.; Gauchia, L.; Voncila, E.; Sanz, J.

2015-01-01

Highlights: • Dynamical modeling of a 50 A h battery pack composed of 56 cells. • Detailed analysis of SOC tests at realistic performance range imposed by BMS. • We propose an electrical circuit that improves how the battery capacity is modeled. • The model is validated in the SOC range using a real-time experimental setup. - Abstract: This paper presents the modeling of a 50 A h battery pack composed of 56 cells, taking into account real battery performance conditions imposed by the BMS control. The modeling procedure starts with a detailed analysis of experimental charge and discharge SOC tests. Results from these tests are used to obtain the battery model parameters at a realistic performance range (20–80% SOC). The model topology aims to better describe the finite charge contained in a battery pack. The model has been validated at three different SOC values in order to verify the model response at real battery pack operation conditions. The validation tests show that the battery pack model is able to simulate the real battery response with excellent accuracy in the range tested. The proposed modeling procedure is fully applicable to any Li-ion battery pack, regardless of the number of series or parallel cells or its rated capacity

Linear superposition solutions to nonlinear wave equations

International Nuclear Information System (INIS)

Liu Yu

2012-01-01

The solutions to a linear wave equation can satisfy the principle of superposition, i.e., the linear superposition of two or more known solutions is still a solution of the linear wave equation. We show in this article that many nonlinear wave equations possess exact traveling wave solutions involving hyperbolic, triangle, and exponential functions, and the suitable linear combinations of these known solutions can also constitute linear superposition solutions to some nonlinear wave equations with special structural characteristics. The linear superposition solutions to the generalized KdV equation K(2,2,1), the Oliver water wave equation, and the k(n, n) equation are given. The structure characteristic of the nonlinear wave equations having linear superposition solutions is analyzed, and the reason why the solutions with the forms of hyperbolic, triangle, and exponential functions can form the linear superposition solutions is also discussed

Solution chemistry and separation of metal ions in leached solution

International Nuclear Information System (INIS)

Shibata, J.

1991-01-01

The method to presume a dissolved state of metal ions in an aqueous solution and the technology to separate and concentrate metal ions in a leached solution are described in this paper. It is very important for the separation of metal ions to know the dissolved state of metal ions. If we know the composition of an aqueous solution and the stability constants of metal-ligand complexes, we can calculate and estimate the concentration of each species in the solution. Then, we can decide the policy to separate and concentrate metal ions. There are several methods for separation and purification; hydroxide precipitation method, sulfide precipitation method, solvent extraction method and ion exchange resin method. Solvent extraction has been used in purification processes of copper refinery, uranium refinery, platinum metal refinery and rare earth metal refinery. Fundamental process of solvent extraction, a kind of commercial extractants, a way of determining a suitable extractant and an equipment are discussed. Finally, it will be emphasized how the separation of rare earths is improved in solvent extraction. (author) 21 figs., 8 tabs., 8 refs

A new modular procedure for industrial plant simulations and its reliable implementation

International Nuclear Information System (INIS)

Carcasci, C.; Marini, L.; Morini, B.; Porcelli, M.

2016-01-01

Modeling of industrial plants, and especially energy systems, has become increasingly important in industrial engineering and the need for accurate information on their behavior has grown along with the complexity of the industrial processes. Consequently, accurate and flexible simulation tools became essential yielding the development of modular codes. The aim of this work is to propose a new modular mathematical modeling for industrial plant simulation and its reliable numerical implementation. Regardless of their layout, a large class of plant's configurations is modeled by a library of elementary parts; then the physical properties, compositions of the working fluid, and plant's performance are estimated. Each plant component is represented by equations modeling fundamental mechanical and thermodynamic laws and giving rise to a system of algebraic nonlinear equations; remarkably, suitable restrictions on the variables of such nonlinear equations are imposed to guarantee solutions of physical meaning. The proposed numerical procedure combines an outer iterative process which refines plants characteristic parameters and an inner one which solves the arising nonlinear systems and consists of a trust-region solver for bound-constrained nonlinear equalities. The new procedure has been validated performing simulations against an existing modular tool on two compression train arrangements with both series and parallel-mounted compressors. - Highlights: • A numerical modular tool for industrial plants simulation is presented. • Mathematical modeling is thoroughly described. • Solution of the nonlinear system is performed by a trust-region Gauss–Newton solver. • A detailed explanation of the optimization solver named TRESNEI is provided. • Code flexibility and robustness are investigated through numerical simulations.

Development of extraction procedure for determination of mercury species using SPME-assisted dispersive derivative agent

Science.gov (United States)

Abdullah, Md Pauzi; Khalik, Wan Mohd Afiq Wan Mohd; Othman, Mohamed Rozali

2016-11-01

The extraction procedure for determination of low level mercury using solid phase microextraction was successfully carried out. Design of experimental works using factorial design and central composite design were applied to screen and predict the optimum condition for extraction step. In this study, variables namely concentration level (5 % m/v) and volume of derivatization solution (150 µL) has depicted as main effect for controlling the suitability of derivative reagent condition. Maximum of signal response (account as total peak areas for mercury species) was obtained when extraction procedure was set up at pH of water sample (5.8), extraction time (14 min), extraction temperature (43 °C) and stirring rate (450 rpm). Reducing time required to reach equilibrium is new improvement achieved in this study. Detection limit for each species (MeHg 26.17 ngL-1; EtHg 48.84 ngL-1 and IHg 14.11 ngL-1) was calculated lower than our previous work. Recovery, repeatability and reproducibility trial were recorded varied at acceptable range and relative standard deviation was calculated below than 10 %.

PEM fuel cell model suitable for energy optimization purposes

International Nuclear Information System (INIS)

Caux, S.; Hankache, W.; Fadel, M.; Hissel, D.

2010-01-01

Many fuel cell stack models or fuel cell system models exist. A model must be built with a main objective, sometimes for accurate electro-chemical behavior description, sometimes for optimization procedure at a system level. In this paper, based on the fundamental reactions present in a fuel cell stack, an accurate model and identification procedure is presented for future energy management in a Hybrid Electrical Vehicle (HEV). The proposed approach extracts all important state variables in such a system and based on the control of the fuel cell's gas flows and temperature, simplification arises to a simple electrical model. Assumptions verified due to the control of the stack allow simplifying the relationships within keeping accuracy in the description of a global fuel cell stack behavior from current demand to voltage. Modeled voltage and current dynamic behaviors are compared with actual measurements. The obtained accuracy is sufficient and less time-consuming (versus other previously published system-oriented models) leading to a suitable model for optimization iterative off-line algorithms.

PEM fuel cell model suitable for energy optimization purposes

Energy Technology Data Exchange (ETDEWEB)

Caux, S.; Hankache, W.; Fadel, M. [LAPLACE/CODIASE: UMR CNRS 5213, Universite de Toulouse - INPT, UPS, - ENSEEIHT: 2 rue Camichel BP7122, 31071 Toulouse (France); CNRS, LAPLACE, F-31071 Toulouse (France); Hissel, D. [FEMTO-ST ENISYS/FCLAB, UMR CNRS 6174, University of Franche-Comte, Rue Thierry Mieg, 90010 Belfort (France)

2010-02-15

Many fuel cell stack models or fuel cell system models exist. A model must be built with a main objective, sometimes for accurate electro-chemical behavior description, sometimes for optimization procedure at a system level. In this paper, based on the fundamental reactions present in a fuel cell stack, an accurate model and identification procedure is presented for future energy management in a Hybrid Electrical Vehicle (HEV). The proposed approach extracts all important state variables in such a system and based on the control of the fuel cell's gas flows and temperature, simplification arises to a simple electrical model. Assumptions verified due to the control of the stack allow simplifying the relationships within keeping accuracy in the description of a global fuel cell stack behavior from current demand to voltage. Modeled voltage and current dynamic behaviors are compared with actual measurements. The obtained accuracy is sufficient and less time-consuming (versus other previously published system-oriented models) leading to a suitable model for optimization iterative off-line algorithms. (author)

clay nanocomposite by solution intercalation technique

Indian Academy of Sciences (India)

Polymer–clay nanocomposites of commercial polystyrene (PS) and clay laponite were prepared via solution intercalation technique. Laponite was modified suitably with the well known cationic surfactant cetyltrimethyl ammonium bromide by ion-exchange reaction to render laponite miscible with hydrophobic PS.

Glucose buffer is suitable for blood group conversion with α-N acetylgalactosaminidase and α-galactosidase.

Science.gov (United States)

Gao, Hong-Wei; Li, Su-Bo; Bao, Guo-Qiang; Zhang, Xue; Li, Hui; Wang, Ying-Li; Tan, Ying-Xia; Ji, Shou-Ping; Gong, Feng

2014-01-01

It is well known that the buffer plays a key role in the enzymatic reaction involved in blood group conversion. In previous study, we showed that a glycine buffer is suitable for A to O or B to O blood group conversion. In this study, we investigated the use of 5% glucose and other buffers for A to O or B to O blood group conversion by α-N-acetylgalactosaminidase or α-galactosidase. We compared the binding ability of α-N-acetylgalactosaminidase/α-galactosidase with red blood cells (RBC) in different reaction buffers, such as normal saline, phosphate-buffered saline (PBS), a disodium hydrogen phosphate-based buffer (PCS), and 5% commercial glucose solution. The doses of enzymes necessary for the A/B to O conversion in different reaction buffers were determined and compared. The enzymes' ability to bind to RBC was evaluated by western blotting, and routine blood typing and fluorescence activated cell sorting was used to evaluate B/A to O conversion efficiency. The A to O conversion efficiency in glucose buffer was similar to that in glycine buffer with the same dose (>0.06 mg/mL pRBC). B to O conversion efficiency in glucose buffer was also similar to that in glycine buffer with the same dose (>0.005 mg/mL pRBC). Most enzymes could bind with RBC in glycine or glucose buffer, but few enzymes could bind with RBC in PBS, PCS, or normal saline. These results indicate that 5% glucose solution provides a suitable condition for enzymolysis, especially for enzymes combining with RBC. Meanwhile, the conversion efficiency of A/B to O was similar in glucose buffer and glycine buffer. Moreover, 5% glucose solution has been used for years in venous transfusion, it is safe for humans and its cost is lower. Our results do, therefore, suggest that 5% glucose solution could become a novel suitable buffer for A/B to O blood group conversion.

Comparison of simple and economical photocatalyst immobilisation procedures

DEFF Research Database (Denmark)

Lim, L.L.P.; Lynch, R.J.; In, Su-il

2009-01-01

Photocatalysis is extremely useful for the removal of organic contaminants in water. However, the conditions used for preparing and fixing the catalyst to a substrate have a great effect on its performance. The determination of a suitable immobilisation procedure for specific application becomes...

The Macdonald and Savage titrimetric procedure scaled down to 4 mg sized plutonium samples. P. 1

International Nuclear Information System (INIS)

Kuvik, V.; Lecouteux, C.; Doubek, N.; Ronesch, K.; Jammet, G.; Bagliano, G.; Deron, S.

1992-01-01

The original Macdonald and Savage amperometric method scaled down to milligram-sized plutonium samples was further modified. The electro-chemical process of each redox step and the end-point of the final titration were monitored potentiometrically. The method is designed to determine 4 mg of plutonium dissolved in nitric acid solution. It is suitable for the direct determination of plutonium in non-irradiated fuel with a uranium-to-plutonium ratio of up to 30. The precision and accuracy are ca. 0.05-0.1% (relative standard deviation). Although the procedure is very selective, the following species interfere: vanadyl(IV) and vanadate (almost quantitatively), neptunium (one electron exchange per mole), nitrites, fluorosilicates (milligram amounts yield a slight bias) and iodates. (author). 15 refs.; 8 figs.; 7 tabs

Radiation doses to patients in haemodynamic procedures

International Nuclear Information System (INIS)

Canadillas-Perdomo, B.; Catalan-Acosta, A.; Hernandez-Armas, J.; Perez-Martin, C.; Armas-Trujillo, D. de

2001-01-01

Interventional radio-cardiology gives high doses to patients due to high values of fluoroscopy times and large series of radiographic images. The main objective of the present work is the determination of de dose-area product (DAP) in patients of three different types of cardiology procedures with X-rays. The effective doses were estimated trough the organ doses values measured with thermoluminescent dosimeters (TLDs-100), suitable calibrated, placed in a phantom type Rando which was submitted to the same radiological conditions corresponding to the procedures made on patients. The values for the effective doses in the procedures CAD Seldinger was 6.20 mSv on average and 1.85mSv for pacemaker implants. (author)

Radiation doses to patients in haemodynamic procedures

Energy Technology Data Exchange (ETDEWEB)

Canadillas-Perdomo, B; Catalan-Acosta, A; Hernandez-Armas, J [Servicio de Fisica Medica, Hospital Universitario de Canarias, La Laguna, Tenerife (Spain); Perez-Martin, C [Servicio de Ingenieria Biomedica, Hospital Universitario de Canarias, La Laguna, Tenerife (Spain); Armas-Trujillo, D de [Servicio de Cardiologia, Hospital Universitario de Canarias, La Laguna, Tenerife (Spain)

2001-03-01

Interventional radio-cardiology gives high doses to patients due to high values of fluoroscopy times and large series of radiographic images. The main objective of the present work is the determination of de dose-area product (DAP) in patients of three different types of cardiology procedures with X-rays. The effective doses were estimated trough the organ doses values measured with thermoluminescent dosimeters (TLDs-100), suitable calibrated, placed in a phantom type Rando which was submitted to the same radiological conditions corresponding to the procedures made on patients. The values for the effective doses in the procedures CAD Seldinger was 6.20 mSv on average and 1.85mSv for pacemaker implants. (author)

Novel third-order Lovelock wormhole solutions

Science.gov (United States)

Mehdizadeh, Mohammad Reza; Lobo, Francisco S. N.

2016-06-01

In this work, we consider wormhole geometries in third-order Lovelock gravity and investigate the possibility that these solutions satisfy the energy conditions. In this framework, by applying a specific equation of state, we obtain exact wormhole solutions, and by imposing suitable values for the parameters of the theory, we find that these geometries satisfy the weak energy condition in the vicinity of the throat, due to the presence of higher-order curvature terms. Finally, we trace out a numerical analysis, by assuming a specific redshift function, and find asymptotically flat solutions that satisfy the weak energy condition throughout the spacetime.

Quality assurance methods and procedures for accepting radioactive waste for final storage

International Nuclear Information System (INIS)

Wenger, R.

1992-01-01

The concept of quality assurance for the final storage of radioactive materials is presented together with the procedure, characterisation, procedural development and documentation involved. Other topics include the assessment of the material to find its suitability for final storage and the tests for transport. 4 figs., 9 refs

A procedure for effective Dancoff factor calculation

International Nuclear Information System (INIS)

Milosevic, M.

2001-01-01

In this paper, a procedure for Dancoff factors calculation based on equivalence principle and its application in the SCALE-4.3 code system is described. This procedure is founded on principle of conservation of neutron absorption for resolved resonance range in a heterogeneous medium and an equivalent medium consisted of an infinite array of two-region pin cells, where the presence of other fuel rods is taken into account through a Dancoff factor. The neutron absorption in both media is obtained using a fine-group elastic slowing-down calculation. This procedure is implemented in a design oriented lattice physics code, which is applicable for any geometry where the method of collision probability is possible to apply to get a flux solution. Proposed procedure was benchmarked for recent exercise that represents a system with a fuel double heterogeneity, i.e., fuel in solid form (pellets) surrounded by fissile material in solution, and for a 5x5 irregular pressurised water reactor assembly, which requires different Dancoff factors. (author)

A computational procedure to improve airfoil performance considering shape and flow interactions

International Nuclear Information System (INIS)

Darbandi, M.; Taghvaey, M.J.; Schneider, G.E.

2004-01-01

Despite remarkable progress in shape design issue, there is still room to work on this topic considering different flow field conditions and specific aerodynamic applications. Today, the optimization techniques are known as a major tool to reach the best possible aerodynamic shape for some specific conditions. In general direct optimization techniques, the optimization process is started from choosing a suitable primitive shape and the shape is improved by suitable considerations of the design objectives and constraints. In a similar attempt, we develop a new optimization strategy to improve the airfoil shape for specified applications. The strategy involves several stages. It includes to determine the flow conditions and design parameters, to establish the objective function, to select a suitable primitive shape, to generate a mechanism for inserting gradual shape changes, to generate grids around each defined shape, to solve the flow field for each separate shape, to collect the solution data, to change the discrete data to the continuous distribution functions, to construct the objective function, and to minimize the objective function using the steepest descent approach. No constraint function is incorporated into the constructed objective function. The cruise flight of an aircraft at an specified altitude is supposed to be the flow field conditions around the proposed airfoil. Nevertheless, the flow field is assumed to be viscous and compressible as well as turbulent. The procedure is tested starting from two generic airfoil shapes with and without camber. The developed algorithm works well for both cases; however, it may not converge to identical shapes if the primitive shapes are not identical. (author)

A computational procedure to improve airfoil performance considering shape and flow interactions

Energy Technology Data Exchange (ETDEWEB)

Darbandi, M.; Taghvaey, M.J. [Sharif Univ. of Technology, Dept. of Aerospace Engineering, Tehran (Iran, Islamic Republic of)]. E-mail: darbandi@sharif.edu; Schneider, G.E. [Univ. of Waterloo, Dept. of Mechanical Engineering, Waterloo, Ontario (Canada)

2004-07-01

Despite remarkable progress in shape design issue, there is still room to work on this topic considering different flow field conditions and specific aerodynamic applications. Today, the optimization techniques are known as a major tool to reach the best possible aerodynamic shape for some specific conditions. In general direct optimization techniques, the optimization process is started from choosing a suitable primitive shape and the shape is improved by suitable considerations of the design objectives and constraints. In a similar attempt, we develop a new optimization strategy to improve the airfoil shape for specified applications. The strategy involves several stages. It includes to determine the flow conditions and design parameters, to establish the objective function, to select a suitable primitive shape, to generate a mechanism for inserting gradual shape changes, to generate grids around each defined shape, to solve the flow field for each separate shape, to collect the solution data, to change the discrete data to the continuous distribution functions, to construct the objective function, and to minimize the objective function using the steepest descent approach. No constraint function is incorporated into the constructed objective function. The cruise flight of an aircraft at an specified altitude is supposed to be the flow field conditions around the proposed airfoil. Nevertheless, the flow field is assumed to be viscous and compressible as well as turbulent. The procedure is tested starting from two generic airfoil shapes with and without camber. The developed algorithm works well for both cases; however, it may not converge to identical shapes if the primitive shapes are not identical. (author)

Nuclear fuel technology - Determination of milligram amounts of plutonium in nitric acid solutions - Potentiometric titration with potassium dichromate after oxidation by Ce(IV) and reduction by Fe(II)

International Nuclear Information System (INIS)

2000-01-01

This International Standard describes a precise and accurate analytical method for determining 1 mg to 5 mg of plutonium per millilitre in nitric acid solutions. The method is very selective for plutonium. It is suitable for the direct determination of plutonium in materials ranging from pure product solutions, to solutions of mixed nuclear materials with a uranium/plutonium ratio up to 20:1. However, potential application to the assay of plutonium in solutions of irradiated nuclear fuels and solutions of mixed nuclear materials with uranium/plutonium ratios of 20:1 to 33:1 has not yet been documented. The method recommends that the aliquot be weighed and that the titration burettes be calibrated gravimetrically in order to obtain adequate precision and accuracy. This does not preclude using any alternative technique which can be shown to give an equivalent accuracy. As the reproducibility of the reaction conditions is important to maintain good performance, extensive automatization of the procedure is beneficial

Procedure and equipment for continuous manufacture of solutions

International Nuclear Information System (INIS)

Stiefel, M.

1979-01-01

In order to manufacture boric acid solution for reactor commissioning, the heated water is divided into a main and subsidiary flow, and the total amount of the salt is added to the subsidiary flow. Mixing of the main flow with the salt-containing subsidiary flow takes place on a mixing column. Undissolved salt is removed in a hydro-cyclotron. Preheating of the water takes place in a recuperator heat exchanger and a through boiler provides the final temperatures. (HK) [de

Partitioning high-level waste from alkaline solution: A literature survey

International Nuclear Information System (INIS)

Marsh, S.F.

1993-05-01

Most chemical partitioning procedures are designed for acidic feed solutions. However, the high-level waste solutions in the underground storage tanks at US Department of Energy defense production sites are alkaline. Effective partitioning procedures for alkaline solutions could decrease the need to acidify these solutions and to dissolve the solids in acid, which would simplify subsequent processing and decrease the generation of secondary waste. The author compiles candidate technologies from his review of the chemical literature, experience, and personal contacts. Several of these are recommended for evaluation

Helicopter Flight Procedures for Community Noise Reduction

Science.gov (United States)

Greenwood, Eric

2017-01-01

A computationally efficient, semiempirical noise model suitable for maneuvering flight noise prediction is used to evaluate the community noise impact of practical variations on several helicopter flight procedures typical of normal operations. Turns, "quick-stops," approaches, climbs, and combinations of these maneuvers are assessed. Relatively small variations in flight procedures are shown to cause significant changes to Sound Exposure Levels over a wide area. Guidelines are developed for helicopter pilots intended to provide effective strategies for reducing the negative effects of helicopter noise on the community. Finally, direct optimization of flight trajectories is conducted to identify low noise optimal flight procedures and quantify the magnitude of community noise reductions that can be obtained through tailored helicopter flight procedures. Physically realizable optimal turns and approaches are identified that achieve global noise reductions of as much as 10 dBA Sound Exposure Level.

Hot test of a TALSPEAK procedure for separation of actinides and lanthanides using recirculating DTPA-lactic acid solution

International Nuclear Information System (INIS)

Persson, G.; Svantesson, I.; Wingefors, S.; Liljenzin, J.O.

1984-01-01

Results are reported from a hot test of a TALSPEAK type process for separation of higher actinides (Am, Cm) from lanthanides. Actinides and lanthanides are extracted by 1 M HDEHP and separated by selective strip of the actinides, using a mixture of DTPA and lactic acid (reversed TALSPEAK process). In order to minimize the generation of secondary waste, a procedure using recirculating DTPA-Lactic acid solution has been developed. A separation factor between Am and Eu of 132 was achieved. In regard to separations of Am and Cm from commercial HLLW (high level liquid wastes), the factor corresponds to 1.5% of the lanthanide group remaining with the actinides. The loss of Am was about 0.2%. 9 figures, 3 tables

Influence of bio-solution pretreatment on the structure, reactivity and torrefaction of bamboo

International Nuclear Information System (INIS)

Chen, Wei-Hsin; Chu, Yen-Shih; Lee, Wen-Jhy

2017-01-01

Highlights: • A bio-solution of natural organic enzyme-7F (NOE-7F) is used to pretreat bamboo. • The bio-solution removes hemicellulose in powdered bamboo significantly. • Bamboo powder pretreated by bio-solution may be feasible for producing bioethanol. • Penetration of bio-solution into block bamboo controls the pretreatment mechanism. • The homogeneity of bamboo is improved by the bio-solution pretreatment. - Abstract: A bio-solution of natural organic enzyme-7F (NOE-7F) is used to pretreat bamboo, with emphasis on the influence the pretreatment upon the structure, reactivity, and torrefaction of the biomass. Two different operating modes accompanied by five different soaking durations are considered. In Mode 1 the bamboo is ground followed by pretreated by the bio-solution, and an inverse procedure is used in Mode 2. The results indicate that, with the operation of Mode 1, NOE-7F removes hemicellulose in the bamboo significantly, thereby improving the homogeneity of the biomass. This pretreated bamboo may be feasible for enzymatic hydrolysis to produce bioethanol. The penetration of the bio-solution into block bamboo becomes the controlling mechanism under Mode 2 operation, and therefore relatively less hemicellulose is consumed from Mode 2. The ignition and burnout temperatures of the pretreated bamboo are higher than those of the raw bamboo, revealing the lower reactivity and higher storage safety of the former. The atomic H/C and O/C ratios as well as the calorific value of the bamboo are insensitive to the pretreatments, whereas the crystalline structure of cellulose is affected by the bio-solution to a certain extent, regardless of Mode 1 or Mode 2 operation. This suggests that torrefaction is required if the pretreated bamboo is employed as a fuel. The pretreated bamboo with Mode 2 is more suitable for torrefaction because of higher torrefaction severity.

Solution of the stellar structure equations in Eulerian coordinates

International Nuclear Information System (INIS)

Deupree, R.G.

1976-01-01

The equations of hydrostatic and thermal equilibrium, assuming only radiative energy transport and spherical symmetry, are solved in Eulerian coordinates by a suitable modification of the Henyey method. An Eulerian approach may possibly be more suitably extended to more spatial dimensions than the usual Lagrangian procedure. The principle advantage of this method is that the equations of hydrostatic and thermal equilibrium and Poisson's equation may be solved simultaneously

[Climatic suitability of citrus in subtropical China].

Science.gov (United States)

Duan, Hai-Lai; Qian, Huai-Sui; Li, Ming-Xia; Du, Yao-Dong

2010-08-01

By applying the theories of ecological suitability and the methods of fuzzy mathematics, this paper established a climatic suitability model for citrus, calculated and evaluated the climatic suitability and its spatiotemporal differences for citrus production in subtropical China, and analyzed the climatic suitability of citrus at its different growth stages and the mean climatic suitability of citrus in different regions of subtropical China. The results showed that the citrus in subtropical China had a lower climatic suitability and a higher risk at its flower bud differentiation stage, budding stage, and fruit maturity stage, but a higher climatic suitability and a lower risk at other growth stages. Cold damage and summer drought were the key issues affecting the citrus production in subtropical China. The citrus temperature suitability represented a latitudinal zonal pattern, i. e., decreased with increasing latitude; its precipitation suitability was high in the line of "Sheyang-Napo", medium in the southeast of the line, low in the northwest of the line, and non in high mountainous area; while the sunlight suitability was in line with the actual duration of sunshine, namely, higher in high-latitude areas than in low-latitude areas, and higher in high-altitude areas than in plain areas. Limited by temperature factor, the climatic suitability was in accordance with temperature suitability, i. e., south parts had a higher suitability than north parts, basically representing latitudinal zonal pattern. From the analysis of the inter-annual changes of citrus climatic suitability, it could be seen that the citrus climatic suitability in subtropical China was decreasing, and had obvious regional differences, suggesting that climate change could bring about the changes in the regions suitable for citrus production and in the key stages of citrus growth.

Automated MAD and MIR structure solution

International Nuclear Information System (INIS)

Terwilliger, Thomas C.; Berendzen, Joel

1999-01-01

A fully automated procedure for solving MIR and MAD structures has been developed using a scoring scheme to convert the structure-solution process into an optimization problem. Obtaining an electron-density map from X-ray diffraction data can be difficult and time-consuming even after the data have been collected, largely because MIR and MAD structure determinations currently require many subjective evaluations of the qualities of trial heavy-atom partial structures before a correct heavy-atom solution is obtained. A set of criteria for evaluating the quality of heavy-atom partial solutions in macromolecular crystallography have been developed. These have allowed the conversion of the crystal structure-solution process into an optimization problem and have allowed its automation. The SOLVE software has been used to solve MAD data sets with as many as 52 selenium sites in the asymmetric unit. The automated structure-solution process developed is a major step towards the fully automated structure-determination, model-building and refinement procedure which is needed for genomic scale structure determinations

Sweet Solutions to Reduce Procedural Pain in Neonates: A Meta-analysis.

Science.gov (United States)

Harrison, Denise; Larocque, Catherine; Bueno, Mariana; Stokes, Yehudis; Turner, Lucy; Hutton, Brian; Stevens, Bonnie

2017-01-01

Abundant evidence of sweet taste analgesia in neonates exists, yet placebo-controlled trials continue to be conducted. To review all trials evaluating sweet solutions for analgesia in neonates and to conduct cumulative meta-analyses (CMAs) on behavioral pain outcomes. (1) Data from 2 systematic reviews of sweet solutions for newborns; (2) searches ending 2015 of CINAHL, Medline, Embase, and psychINFO. Two authors screened studies for inclusion, conducted risk-of-bias ratings, and extracted behavioral outcome data for CMAs. CMA was performed using random effects meta-analysis. One hundred and sixty-eight studies were included; 148 (88%) included placebo/no-treatment arms. CMA for crying time included 29 trials (1175 infants). From the fifth trial in 2002, there was a statistically significant reduction in mean cry time for sweet solutions compared with placebo (-27 seconds, 95% confidence interval [CI] -51 to -4). By the final trial, CMA was -23 seconds in favor of sweet solutions (95% CI -29 to -18). CMA for pain scores included 50 trials (3341 infants). Results were in favor of sweet solutions from the second trial (0.5, 95% CI -1 to -0.1). Final results showed a standardized mean difference of -0.9 (95% CI -1.1 to -0.7). We were unable to use or obtain data from many studies to include in the CMA. Evidence of sweet taste analgesia in neonates has existed since the first published trials, yet placebo/no-treatment, controlled trials have continued to be conducted. Future neonatal pain studies need to select more ethically responsible control groups. Copyright © 2017 by the American Academy of Pediatrics.

Catheter for Cleaning Surgical Optics During Surgical Procedures: A Possible Solution for Residue Buildup and Fogging in Video Surgery.

Science.gov (United States)

de Abreu, Igor Renato Louro Bruno; Abrão, Fernando Conrado; Silva, Alessandra Rodrigues; Corrêa, Larissa Teresa Cirera; Younes, Riad Nain

2015-05-01

Currently, there is a tendency to perform surgical procedures via laparoscopic or thoracoscopic access. However, even with the impressive technological advancement in surgical materials, such as improvement in quality of monitors, light sources, and optical fibers, surgeons have to face simple problems that can greatly hinder surgery by video. One is the formation of "fog" or residue buildup on the lens, causing decreased visibility. Intracavitary techniques for cleaning surgical optics and preventing fog formation have been described; however, some of these techniques employ the use of expensive and complex devices designed solely for this purpose. Moreover, these techniques allow the cleaning of surgical optics when they becomes dirty, which does not prevent the accumulation of residue in the optics. To solve this problem we have designed a device that allows cleaning the optics with no surgical stops and prevents the fogging and residue accumulation. The objective of this study is to evaluate through experimental testing the effectiveness of a simple device that prevents the accumulation of residue and fogging of optics used in surgical procedures performed through thoracoscopic or laparoscopic access. Ex-vivo experiments were performed simulating the conditions of residue presence in surgical optics during a video surgery. The experiment consists in immersing the optics and catheter set connected to the IV line with crystalloid solution in three types of materials: blood, blood plus fat solution, and 200 mL of distilled water and 1 vial of methylene blue. The optics coupled to the device were immersed in 200 mL of each type of residue, repeating each immersion 10 times for each distinct residue for both thirty and zero degrees optics, totaling 420 experiments. A success rate of 98.1% was observed after the experiments, in these cases the device was able to clean and prevent the residue accumulation in the optics.

A rapid method for the extraction and analysis of carotenoids and other hydrophobic substances suitable for systems biology studies with photosynthetic bacteria.

Science.gov (United States)

Bóna-Lovász, Judit; Bóna, Aron; Ederer, Michael; Sawodny, Oliver; Ghosh, Robin

2013-10-11

A simple, rapid, and inexpensive extraction method for carotenoids and other non-polar compounds present in phototrophic bacteria has been developed. The method, which has been extensively tested on the phototrophic purple non-sulphur bacterium Rhodospirillum rubrum, is suitable for extracting large numbers of samples, which is common in systems biology studies, and yields material suitable for subsequent analysis using HPLC and mass spectroscopy. The procedure is particularly suitable for carotenoids and other terpenoids, including quinones, bacteriochlorophyll a and bacteriopheophytin a, and is also useful for the analysis of polar phospholipids. The extraction procedure requires only a single step extraction with a hexane/methanol/water mixture, followed by HPLC using a Spherisorb C18 column, with a mobile phase consisting of acetone-water and a non-linear gradient of 50%-100% acetone. The method was employed for examining the carotenoid composition observed during microaerophilic growth of R. rubrum strains, and was able to determine 18 carotenoids, 4 isoprenoid-quinones, bacteriochlorophyll a and bacteriopheophytin a as well as four different phosphatidylglycerol species of different acyl chain compositions. The analytical procedure was used to examine the dynamics of carotenoid biosynthesis in the major and minor pathways operating simultaneously in a carotenoid biosynthesis mutant of R. rubrum.

A Rapid Method for the Extraction and Analysis of Carotenoids and Other Hydrophobic Substances Suitable for Systems Biology Studies with Photosynthetic Bacteria

Directory of Open Access Journals (Sweden)

Oliver Sawodny

2013-10-01

Full Text Available A simple, rapid, and inexpensive extraction method for carotenoids and other non-polar compounds present in phototrophic bacteria has been developed. The method, which has been extensively tested on the phototrophic purple non-sulphur bacterium Rhodospirillum rubrum, is suitable for extracting large numbers of samples, which is common in systems biology studies, and yields material suitable for subsequent analysis using HPLC and mass spectroscopy. The procedure is particularly suitable for carotenoids and other terpenoids, including quinones, bacteriochlorophyll a and bacteriopheophytin a, and is also useful for the analysis of polar phospholipids. The extraction procedure requires only a single step extraction with a hexane/methanol/water mixture, followed by HPLC using a Spherisorb C18 column, with a mobile phase consisting of acetone-water and a non-linear gradient of 50%–100% acetone. The method was employed for examining the carotenoid composition observed during microaerophilic growth of R. rubrum strains, and was able to determine 18 carotenoids, 4 isoprenoid-quinones, bacteriochlorophyll a and bacteriopheophytin a as well as four different phosphatidylglycerol species of different acyl chain compositions. The analytical procedure was used to examine the dynamics of carotenoid biosynthesis in the major and minor pathways operating simultaneously in a carotenoid biosynthesis mutant of R. rubrum.

Existence of Positive Solutions for Nonlinear Eigenvalue Problems

Directory of Open Access Journals (Sweden)

Wong Fu-Hsiang

2010-01-01

Full Text Available We use a fixed point theorem in a cone to obtain the existence of positive solutions of the differential equation, , , with some suitable boundary conditions, where is a parameter.

The Median Solution of the Newsvendor Problem and Some Observations

Directory of Open Access Journals (Sweden)

Sinha Pritibhushan

2015-09-01

Full Text Available We consider the median solution of the Newsvendor Problem. Some properties of such a solution are shown through a theoretical analysis and a numerical experiment. Sometimes, though not often, median solution may be better than solutions maximizing expected profit, or maximizing minimum possible, over distribution with the same average and standard deviation, expected profit, according to some criteria. We discuss the practical suitability of the objective function set and the solution derived, for the Newsvendor Problem, and other such random optimization problems.

Membrane separation of ionic liquid solutions

Science.gov (United States)

Campos, Daniel; Feiring, Andrew Edward; Majumdar, Sudipto; Nemser, Stuart

2015-09-01

A membrane separation process using a highly fluorinated polymer membrane that selectively permeates water of an aqueous ionic liquid solution to provide dry ionic liquid. Preferably the polymer is a polymer that includes polymerized perfluoro-2,2-dimethyl-1,3-dioxole (PDD). The process is also capable of removing small molecular compounds such as organic solvents that can be present in the solution. This membrane separation process is suitable for drying the aqueous ionic liquid byproduct from precipitating solutions of biomass dissolved in ionic liquid, and is thus instrumental to providing usable lignocellulosic products for energy consumption and other industrial uses in an environmentally benign manner.

48 CFR 570.105-2 - Two-phase design-build selection procedures.

Science.gov (United States)

2010-10-01

... lease construction projects with options to purchase the real property leased. Use the procedures in.... (iii) The capability and experience of potential contractors. (iv) The suitability of the project for...

A comparative assessment of alternative waste management procedures for selected reprocessing wastes

International Nuclear Information System (INIS)

Hickford, G.E.; Plews, M.J.

1983-07-01

This report, which has been prepared by Associated Nuclear Services for the Department of the Environment, presents the results of a study and comparative assessment of management procedures for low and intermediate level solid waste streams arising from current and future fuel reprocessing operations on the Sellafield site. The characteristics and origins of the wastes under study are discussed and a reference waste inventory is presented, based on published information. Waste management strategy in the UK and its implications for waste conditioning, packaging and disposal are discussed. Wastes currently arising which are not suitable for Drigg burial or sea dumping are stored in an untreated form. Work is in hand to provide additional and improved disposal facilities which will accommodate all the waste streams under study. For each waste stream viable procedures are identified for further assessment. The procedures comprise a series of on-site operations-recovery from storage, pre-treatment, treatment, encapsulation, and packaging, prior to storage or disposal of the conditioned waste form. Assessments and comparisons of each procedure for each waste are presented. These address various process, operational, economic, radiological and general safety factors. The results are presented in a series of tables with supporting text. For the majority of wastes direct encapsulation with minimal treatment appears to be a viable procedure. Occupational exposure and general safety are not identified as significant factors governing the choice of procedures. The conditioned wastes meet the general requirements for safe handling during storage and transportation. The less active wastes suitable for disposal by currently available routes meet the appropriate disposal criteria. It is not possible to consider in detail the suitability for disposal of the more active wastes for which disposal facilities are not yet available. (Author)

Procedures for Determining the Performance of Stand-Alone Photovoltaic Systems; TOPICAL

International Nuclear Information System (INIS)

DeBlasio, R.; Durand, S.; Hansen, R.; Hutchinson, P.; Kroposki, B.; McNutt, P.; Rosenthal, A.; Thomas, M.

1999-01-01

This document provides the procedures for determining the performance of stand-alone PV systems. The procedures in this document provide a common approach for evaluating whether a given PV system is suitable to perform the function for which it was designed and manufactured to accomplish, and whether it will provide adequate power to run the load. These procedures cover small stand-alone PV systems. They cover complete outdoor system testing. Test results are valid only for the system that is tested

Land suitability assessment in the catchment area of four Southwestern Atlantic coastal lagoons: multicriteria and optimization modeling.

Science.gov (United States)

Rodriguez-Gallego, Lorena; Achkar, Marcel; Conde, Daniel

2012-07-01

In the present study, a land suitability assessment was conducted in the basin of four Uruguayan coastal lagoons (Southwestern Atlantic) to analyze the productive development while minimizing eutrophication, biodiversity loss and conflicts among different land uses. Suitable land for agriculture, forest, livestock ranching, tourism and conservation sectors were initially established based on a multi-attribute model developed using a geographic information system. Experts were consulted to determine the requirements for each land use sector and the incompatibilities among land use types. The current and potential conflicts among incompatible land use sectors were analyzed by overlapping land suitability maps. We subsequently applied a multi-objective model where land (pixels) with similar suitability was clustered into "land suitability groups", using a two-phase cluster analysis and the Akaike Information Criterion. Finally, a linear programming optimization procedure was applied to allocate land use sectors into land suitable groups, maximizing total suitability and minimizing interference among sectors. Results indicated that current land use overlapped by 4.7 % with suitable land of other incompatible sectors. However, the suitable land of incompatible sectors overlapped in 20.3 % of the study area, indicating a high potential for the occurrence of future conflict. The highest competition was between agriculture and conservation, followed by forest and agriculture. We explored scenarios where livestock ranching and tourism intensified, and found that interference with conservation and agriculture notably increased. This methodology allowed us to analyze current and potential land use conflicts and to contribute to the strategic planning of the study area.

Precipitation of plutonium from acidic solutions using magnesium oxide

International Nuclear Information System (INIS)

Jones, S.A.

1994-01-01

Magnesium oxide will be used as a neutralizing agent for acidic plutonium-containing solutions. It is expected that as the magnesium oxide dissolves, the pH of the solution will rise, and plutonium will precipitate. The resulting solid will be tested for suitability to storage. The liquid is expected to contain plutonium levels that meet disposal limit requirements

Formalizing physical security procedures

NARCIS (Netherlands)

Meadows, C.; Pavlovic, Dusko

Although the problems of physical security emerged more than 10,000 years before the problems of computer security, no formal methods have been developed for them, and the solutions have been evolving slowly, mostly through social procedures. But as the traffic on physical and social networks is now

Prestressed concrete vessels suitable for helium high temperature reactors

International Nuclear Information System (INIS)

Lockett, G.E.; Kinkead, A.N.

1967-02-01

In considering prestressed concrete vessels for use with helium cooled high temperature reactors, a number of new problems arise and projected designs involve new approaches and new solutions. These reactors, having high coolant outlet temperature from the core and relatively high power densities, can be built into compact designs which permit usefully high working pressures. Consequently, steam generators and circulating units tend to be small. Although circuit activity can be kept quite low with coated particle fuels, designs which involve entry for subsequent repair are not favoured, and coupled with the preferred aim of using fully shop fabricated units within the designs with removable steam generators which involve no tube welding inside the vessel. A particular solution uses a number of slim cylindrical assemblies housed in the wall of the pressure vessel and this vessel design concept is presented. The use of helium requires very high sealing standards and one of the important requirements is a vessel design which permits leak testing during construction, so that a repair seal can be made to any faulty part in a liner seam. Very good demountable joint seals can be made without particular difficulty and Dragon experience is used to provide solutions which are suitable for prestressed concrete vessel penetrations. The concept layout is given of a vessel meeting these requirements; the basis of design is outlined and special features of importance discussed. (author)

Separation of iodine from mercury containing scrubbing solutions

Science.gov (United States)

Burger, Leland L.; Scheele, Randall D.

1979-01-01

Radioactive iodines can be recovered from a nitric acid scrub solution containing mercuric nitrate by passing a current through the scrub solution to react the iodine with the mercuric nitrate to form mercuric iodate which precipitates out. The mercuric iodate can then be reacted to recover the radioiodine for further processing into a form suitable for long-term storage and to recover the mercury for recycling.

The benefits of using customized procedure packs.

Science.gov (United States)

Baines, R; Colquhoun, G; Jones, N; Bateman, R

2001-01-01

Discrete item purchasing is the traditional approach for hospitals to obtain consumable supplies for theatre procedures. Although most items are relatively low cost, the management and co-ordination of the supply chain, raising orders, controlling stock, picking and delivering to each operating theatre can be complex and costly. Customized procedure packs provide a solution.

CHARACTERISTICS AND SUITABILITY EVALUATION OF THE ...

African Journals Online (AJOL)

Ifedotun Aina

suggested that the soils were not currently suitable for the production of the two ... crop – land suitability analysis has been used for achieving optimum utilization of the available ... Two methods of land suitability evaluation (FAO frame work and parametric) ..... Characterization and Classification of Onwu River Floodplain.

Periodic solutions of dissipative systems revisited

Directory of Open Access Journals (Sweden)

Górniewicz Lech

2006-01-01

Full Text Available We reprove in an extremely simple way the classical theorem that time periodic dissipative systems imply the existence of harmonic periodic solutions, in the case of uniqueness. We will also show that, in the lack of uniqueness, the existence of harmonics is implied by uniform dissipativity. The localization of starting points and multiplicity of periodic solutions will be established, under suitable additional assumptions, as well. The arguments are based on the application of various asymptotic fixed point theorems of the Lefschetz and Nielsen type.

Periodic solutions of dissipative systems revisited

Directory of Open Access Journals (Sweden)

Lech Górniewicz

2006-05-01

Full Text Available We reprove in an extremely simple way the classical theorem that time periodic dissipative systems imply the existence of harmonic periodic solutions, in the case of uniqueness. We will also show that, in the lack of uniqueness, the existence of harmonics is implied by uniform dissipativity. The localization of starting points and multiplicity of periodic solutions will be established, under suitable additional assumptions, as well. The arguments are based on the application of various asymptotic fixed point theorems of the Lefschetz and Nielsen type.

Fluid mechanics problems and solutions

CERN Document Server

Spurk, Joseph H

1997-01-01

his collection of over 200 detailed worked exercises adds to and complements the textbook Fluid Mechanics by the same author, and illustrates the teaching material through examples. In the exercises the fundamental concepts of Fluid Mechanics are applied to obtaining the solution of diverse concrete problems, and in doing this the student's skill in the mathematical modeling of practical problems is developed. In addition, 30 challenging questions without detailed solutions have been included, and while lecturers will find these questions suitable for examinations and tests, the student himself can use them to check his understanding of the subject.

On the method of solution of the differential-delay Toda equation

Science.gov (United States)

Villarroel, Javier; Ablowitz, Mark J.

1993-09-01

The method of solution of the Toda differential-delay equation, which is a reduction of the Toda equation in 2+1 dimensions, is described. An important feature of the solution process is to obtain and study a novel Riemann-Hilbert problem. The latter problem requires factorization across an infinite number of strips with a suitable branching structure. Explicit soliton solutions are given.

Amperometric titration of indium with edta solution in propanol

International Nuclear Information System (INIS)

Gevorgyan, A.M.; Talipov, Sh.T.; Khadeev, V.A.; Kostylev, V.S.; Khadeeva, L.A.

1980-01-01

Optimum conditions have been chosen for titration of indium with EDTA solution in anhydrous propanol and its mixtures with some aprotic solvents using amperometric and point detection. A procedure is suggested of determining indium microcontents in the presence of large amounts of other elements. The procedure is based on its extraction preseparation followed by direct titration in the extract with a standard EDTA solution [ru

Formal solutions of inverse scattering problems. III

International Nuclear Information System (INIS)

Prosser, R.T.

1980-01-01

The formal solutions of certain three-dimensional inverse scattering problems presented in papers I and II of this series [J. Math. Phys. 10, 1819 (1969); 17 1175 (1976)] are obtained here as fixed points of a certain nonlinear mapping acting on a suitable Banach space of integral kernels. When the scattering data are sufficiently restricted, this mapping is shown to be a contraction, thereby establishing the existence, uniqueness, and continuous dependence on the data of these formal solutions

Strategies for source space limitation in tomographic inverse procedures

International Nuclear Information System (INIS)

George, J.S.; Lewis, P.S.; Schlitt, H.A.; Kaplan, L.; Gorodnitsky, I.; Wood, C.C.

1994-01-01

The use of magnetic recordings for localization of neural activity requires the solution of an ill-posed inverse problem: i.e. the determination of the spatial configuration, orientation, and timecourse of the currents that give rise to a particular observed field distribution. In its general form, this inverse problem has no unique solution; due to superposition and the existence of silent source configurations, a particular magnetic field distribution at the head surface could be produced by any number of possible source configurations. However, by making assumptions concerning the number and properties of neural sources, it is possible to use numerical minimization techniques to determine the source model parameters that best account for the experimental observations while satisfying numerical or physical criteria. In this paper the authors describe progress on the development and validation of inverse procedures that produce distributed estimates of neuronal currents. The goal is to produce a temporal sequence of 3-D tomographic reconstructions of the spatial patterns of neural activation. Such approaches have a number of advantages, in principle. Because they do not require estimates of model order and parameter values (beyond specification of the source space), they minimize the influence of investigator decisions and are suitable for automated analyses. These techniques also allow localization of sources that are not point-like; experimental studies of cognitive processes and of spontaneous brain activity are likely to require distributed source models

The Suitability of Expert System Application in Czech Small and Medium‑Sized Enterprises

Directory of Open Access Journals (Sweden)

Ekaterina Khitilova

2017-01-01

Full Text Available Small and medium-sized enterprises play an important role in the economy of Czech Republic. Expert systems are one of the alternatives evaluated the effectiveness of the relationship between supplier and customer. Currently, measurement and increase in efficiency of supplier-customer relations is very topical subject. The requirements for tools the improvement supplier- customer relationship can be specified on the base the literature analysis. The article defines basic requirements for expert system. The presentation of expert system and its suitability in the surroundings of small and medium sized enterprises is the part of this article. The comparison of the expert system possibilities and the compiled requirements leads to suitability analysis of selected solution. Actual questions and the way of future work are derived from current results, presented in the paper. The article defined the directions of development this expert system.

Identification of suitable media based on hydroponic culture for production Zucchini squash

Directory of Open Access Journals (Sweden)

TP Suvo

2016-12-01

Full Text Available An experiment was conducted to identify the hydroponic culture based suitable media for the production of Zucchini Squash in the Biochemistry Laboratory, Patuakhali Science and Technology University, Dumki, Patuakhali, Bangladesh during 2014. Zucchini plant (Cucurbita pepo L. were grown in closed soilless systems to determine the effect of four different hydroponics media on plant growth, yield and nutrient contents (fruit moisture content, ascorbic acid content on fruit, fruit protein content, protein content in leaves. Three types of substrates (coconut husk, jute, cotton along with Hoagland solution were used in this experiment. Result revealed that media using Jute fiber showed significant effect on plant growth and nutritional values than the other media (media of cotton with Hoagland solution, coconut husk with Hoagland solution and only Hoagland solution. The plant grown using jute media showed the highest plant height (60.33 cm, number of leaves (17.33, yield (1.5 kg plant-1, fruit moisture content (97.33%, Ascorbic acid content in fruit (28.73 mg 100g-1, protein percentage in fruit (1.406% and percentage (1.326% in leaves than the other media. Therefore, with the controlled nutrient supply, less expense, less labor, no use of pesticides or fertilizer with controlled environment the use of jute fiber as a substrate with Hoagland solution can be an effective one.

Determination of Total Carbohydrates in Algal Biomass: Laboratory Analytical Procedure (LAP)

Energy Technology Data Exchange (ETDEWEB)

Van Wychen, Stefanie; Laurens, Lieve M. L.

2016-01-13

This procedure uses two-step sulfuric acid hydrolysis to hydrolyze the polymeric forms of carbohydrates in algal biomass into monomeric subunits. The monomers are then quantified by either HPLC or a suitable spectrophotometric method.

Solidification method for organic solution and processing method of aqueous solution

International Nuclear Information System (INIS)

Kamoshida, Mamoru; Fukazawa, Tetsuo; Yazawa, Noriko; Hasegawa, Toshihiko

1998-01-01

The relative dielectric constant of an organic solution containing polar ingredients is controlled to 13 or less to enable its solidification. The polarity of the organic solution can be evaluated quantitatively by using the relative dielectric constant. If the relative dielectric constant is high, it can be controlled by dilution using a non-polar organic solvent of low relative dielectric constant. With such procedures, solidification can be conducted by using an economical 12-hydroxy stearic acid, process of liquid wastes can be facilitated and the safety can be ensured. (T.M.)

Massively Parallel Algorithms for Solution of Schrodinger Equation

Science.gov (United States)

Fijany, Amir; Barhen, Jacob; Toomerian, Nikzad

1994-01-01

In this paper massively parallel algorithms for solution of Schrodinger equation are developed. Our results clearly indicate that the Crank-Nicolson method, in addition to its excellent numerical properties, is also highly suitable for massively parallel computation.

Rheological evaluation of polymers for EOR. Proper procedures for a laboratory approach

Energy Technology Data Exchange (ETDEWEB)

Kouchaki, S.; Hincapie-Reina, R.; Ganzer, L. [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). ITE

2013-08-01

Some discrepancies exist in the literature concerning polymer EOR (Enhanced Oil Recovery) evaluation. Laboratory investigations are essentials for every particular flooding project, with proper preliminary lab evaluation techniques in order to study the polymer behavior and rheological properties at different reservoir conditions. Different research has been shown variation in procedures during polymer preparation and filtration; affecting the result in the field. Experience from field observation indicates that even high molecular weight (MW) polymers have filtration ratio (F.R) less than 1,5; in that way polymer solutions that are still in range cannot show a good approximation to the field behavior. To deal with the discrepancies, specific procedures based in rheological polymer characterization were adapted. Two different polymers were used for rheology study using a rotational rheometer analyzing some solutions at different conditions. Additionally rheological measurements was used to characterize the apparent viscosity of polymer as a shear rate function, salinity, temperature and polymer concentration, defining additional useful values for simulation evaluations and additionally Newtonian, non-Newtonian, shear viscosity and MW impact were also investigated. Quality control of the solutions was not limited to the conventional indicator 'filtrations ratio', but it was showed how important it is to consider two qualities check indicators, filterability ratio and filterability plot, simultaneously. Results indicated how stable the N-vinyl Pyrrolidone (NVP) Superpusher SAV301 could be in comparison to the Hydrolyzed Polyacrylamide polymer (HPAM) Flopaam 3630S. Despite the high viscosity results from HPAM Flopaam 3630S due to its high MW, the polymer is overly sensitive to factors like temperature, salinity and concentration. Quite the contrary was for polymer solutions with Superpusher SAV301; constant viscosity over a wide shear rate range which is the

Implementation of procedures to NPP Krsko INTRANEK

International Nuclear Information System (INIS)

Gradisar, D.; Krajnc, M.; Kocnar, R.; Spiler, J.

1999-01-01

Part of NEK documentation has already been presented on NEK Intranet such as USAR, Technical Specifications, QA Plan as well as some frequently used series of drawings. At the time being the process of presentation of all procedures (thereinafter INTRANEK procedures) is in progress. The purpose of this project is the presentation of 1600 procedures with average size of 30 pages what is more than 48000 pages altogether. ADOBE PDF (Portable Document Format) has been chosen as the most suitable format for the presentation of procedures on INTRANEK. PDF format meets the following criteria: the outlook of a document page is always the same as an original one and cannot be changed without control. In addition to this, full text search is available as well as easy jump from procedure to procedure. Some changes of working process on internal procedures have to be made before the project start, which determine the responsibility of individual users in the process. The work flow, which enables easy daily maintenance, has been prepared, the rules of both procedure numbering as well as folder contents/name have been set and the server selected. The project was managed and implemented with the extensive use of compute-aided management, document distribution and control, databases, electronics mail and Intranet tools. The results of practical implementation of NEK procedures and our experience with INTRANEK are presented in this paper.(author)

Investigation of waste form materials suitable for immobilizing actinide elements in high-level waste

International Nuclear Information System (INIS)

Hayakawa, Issei; Kamizono, Hiroshi

1992-07-01

The microstructure of waste form materials suitable for immobilizing actinide elements can be classified into the following two categories. (1) Actinide elements are immobilized in an crystallized matrix after the formation of solid solution or compounds. (2) Actinide elements are immobilized in a durable material by encapsulation. Based on crystal chemistry, durability data, phase diagrams, compositions of natural minerals, eleven oxide compounds and one non-oxide compound are pointed out to be new candidates included in category (1). The other survey on material compositions, manufacturing conditions and feasibility shows that SiC, glassy carbon, ZrO 2 , Ti-O-Si-C ceramics are preferable matrix materials included in category (2). Polymers and fine powders are suitable as starting materials for the encapsulation of actinide elements because of their excellent sinterability. (author) 50 refs

Fast identification of folded human protein domains expressed in E. coli suitable for structural analysis

Directory of Open Access Journals (Sweden)

Schlegel Brigitte

2004-03-01

Full Text Available Abstract Background High-throughput protein structure analysis of individual protein domains requires analysis of large numbers of expression clones to identify suitable constructs for structure determination. For this purpose, methods need to be implemented for fast and reliable screening of the expressed proteins as early as possible in the overall process from cloning to structure determination. Results 88 different E. coli expression constructs for 17 human protein domains were analysed using high-throughput cloning, purification and folding analysis to obtain candidates suitable for structural analysis. After 96 deep-well microplate expression and automated protein purification, protein domains were directly analysed using 1D 1H-NMR spectroscopy. In addition, analytical hydrophobic interaction chromatography (HIC was used to detect natively folded protein. With these two analytical methods, six constructs (representing two domains were quickly identified as being well folded and suitable for structural analysis. Conclusion The described approach facilitates high-throughput structural analysis. Clones expressing natively folded proteins suitable for NMR structure determination were quickly identified upon small scale expression screening using 1D 1H-NMR and/or analytical HIC. This procedure is especially effective as a fast and inexpensive screen for the 'low hanging fruits' in structural genomics.

RADCHEM - Radiochemical procedures for the determination of Sr, U, Pu, Am and Cm

Energy Technology Data Exchange (ETDEWEB)

Sidhu, R. [Inst. for Energy Technology (Norway)

2006-04-15

An accurate determination of radionuclides from various sources in the environment is essential for assessment of the potential hazards and suitable countermeasures both in case of accidents, authorised release and routine surveillance. Reliable radiochemical separation and detection techniques are needed for accurate determination of alpha and beta emitters. Rapid analytical methods are needed in case of an accident for early decision-making. The objective of this project has been to compare and evaluate radiochemical procedures used at Nordic laboratories for the determination of strontium, uranium, plutonium, americium and curium. To gather detailed information on the procedures in use, a questionnaire regarding various aspects of radionuclide determination was developed and distributed to all (sixteen) relevant laboratories in the Nordic countries. The response and the procedures used by each laboratory were then discussed between those who answered the questionnaire. This report summaries the findings and gives recommendation on suitable practice. (au)

RADCHEM - Radiochemical procedures for the determination of Sr, U, Pu, Am and Cm

International Nuclear Information System (INIS)

Sidhu, R.

2006-04-01

An accurate determination of radionuclides from various sources in the environment is essential for assessment of the potential hazards and suitable countermeasures both in case of accidents, authorised release and routine surveillance. Reliable radiochemical separation and detection techniques are needed for accurate determination of alpha and beta emitters. Rapid analytical methods are needed in case of an accident for early decision-making. The objective of this project has been to compare and evaluate radiochemical procedures used at Nordic laboratories for the determination of strontium, uranium, plutonium, americium and curium. To gather detailed information on the procedures in use, a questionnaire regarding various aspects of radionuclide determination was developed and distributed to all (sixteen) relevant laboratories in the Nordic countries. The response and the procedures used by each laboratory were then discussed between those who answered the questionnaire. This report summaries the findings and gives recommendation on suitable practice. (au)

Soliton-like solutions to the ordinary Schroedinger equation

International Nuclear Information System (INIS)

Zamboni-Rached, Michel; Recami, Erasmo

2011-01-01

In recent times it has been paid attention to the fact that (linear) wave equations admit of soliton-like solutions, known as Localized Waves or Non-diffracting Waves, which propagate without distortion in one direction. Such Localized Solutions (existing also for K-G or Dirac equations) are a priori suitable, more than Gaussian's, for describing elementary particle motion. In this paper we show that, mutatis mutandis, Localized Solutions exist even for the ordinary Schroedinger equation within standard Quantum Mechanics; and we obtain both approximate and exact solutions, also setting forth for them particular examples. In the ideal case such solutions bear infinite energy, as well as plane or spherical waves: we show therefore how to obtain nite-energy solutions. At last, we briefly consider solutions for a particle moving in the presence of a potential. (author)

Soliton-like solutions to the ordinary Schroedinger equation

Energy Technology Data Exchange (ETDEWEB)

Zamboni-Rached, Michel [Universidade Estadual de Campinas (DMO/FEEC/UNICAMP), Campinas, SP (Brazil). Fac. de Engenharia Eletrica e de Computacao. Dept. de Microondas e Optica; Recami, Erasmo, E-mail: recami@mi.infn.i [Universita Statale di Bergamo, Bergamo (Italy). Facolta di Ingegneria

2011-07-01

In recent times it has been paid attention to the fact that (linear) wave equations admit of soliton-like solutions, known as Localized Waves or Non-diffracting Waves, which propagate without distortion in one direction. Such Localized Solutions (existing also for K-G or Dirac equations) are a priori suitable, more than Gaussian's, for describing elementary particle motion. In this paper we show that, mutatis mutandis, Localized Solutions exist even for the ordinary Schroedinger equation within standard Quantum Mechanics; and we obtain both approximate and exact solutions, also setting forth for them particular examples. In the ideal case such solutions bear infinite energy, as well as plane or spherical waves: we show therefore how to obtain nite-energy solutions. At last, we briefly consider solutions for a particle moving in the presence of a potential. (author)

Analysis of alloys and salt solutions by 'beta'-ray back-scattering

Energy Technology Data Exchange (ETDEWEB)

Bahadur, A; Maji, K D; Kumar, R [National Metallurgical Lab., Jamshedpur (India)

1975-07-01

This investigation reports the results of a study undertaken to assess the suitability of using the GM counter for measuring the intensity of ..beta..-backscattered radiation to determine the chemical composition of binary solid alloys, and aqueous salt solutions containing a metallic radical. The results indicate that the technique is not suitable for the determination of the composition of binary alloys since the error is in the range of 1.2 to 2.3 wt-% metal. The technique can be conveniently adapted for aqueous salt solutions where the maximum error is approximately 0.2 wt-% metal for metallic elements with atomic number greater than 20.

Automated precolumn derivatization procedures in HPLC for biomedical and clinical applications

NARCIS (Netherlands)

Wolf, Johannes Hendrik

1992-01-01

This thesis describes three automated precolumn derivatization procedures for the analysis of carboxylic group-containing compounds. After derivatization with a suitable label, the derivatives are separated on reversed-phashed HPLC and detected by fluorescence. ... Zie: Summary

Collected radiochemical and geochemical procedures

Energy Technology Data Exchange (ETDEWEB)

Kleinberg, J [comp.

1990-05-01

This revision of LA-1721, 4th Ed., Collected Radiochemical Procedures, reflects the activities of two groups in the Isotope and Nuclear Chemistry Division of the Los Alamos National Laboratory: INC-11, Nuclear and radiochemistry; and INC-7, Isotope Geochemistry. The procedures fall into five categories: I. Separation of Radionuclides from Uranium, Fission-Product Solutions, and Nuclear Debris; II. Separation of Products from Irradiated Targets; III. Preparation of Samples for Mass Spectrometric Analysis; IV. Dissolution Procedures; and V. Geochemical Procedures. With one exception, the first category of procedures is ordered by the positions of the elements in the Periodic Table, with separate parts on the Representative Elements (the A groups); the d-Transition Elements (the B groups and the Transition Triads); and the Lanthanides (Rare Earths) and Actinides (the 4f- and 5f-Transition Elements). The members of Group IIIB-- scandium, yttrium, and lanthanum--are included with the lanthanides, elements they resemble closely in chemistry and with which they occur in nature. The procedures dealing with the isolation of products from irradiated targets are arranged by target element.

Significance of MR imaging determining the suitability of patients with metastatic changes in the liver for treatment procedures

International Nuclear Information System (INIS)

Jaruszewska-Orlicka, K.; Czyszkowski, P.; Lasek, W.; Szylberg, T.

2004-01-01

Liver resection is the preferred method of treatment of hepatic metastases. Unfortunately, only 10-20% of patients can be qualified for surgery. One of the alternative palliative methods of treatment is percutaneous alcoholisation of metastatic foci (PEIT). The treatment procedure is determined primarily by the progression of the process in the liver, assessed with non-invasive imaging techniques. Assessment of diagnostic value of MR for patients with focal changes in the liver, an attempt to establish the algorithm of diagnostic and therapeutic procedure, and determination of the criteria qualifying for PEIT. The patients (after USG and BAC) due for liver resection because of liver metastases were subjected to MRI performed with a GYROSCAN NT apparatus with 1T field using a 'body' type solenoid in T2-weighted sequences and STIR/LONG and T1-weighted ones, before and after intravenous administration of a contrast medium in arterial and venous phase, in transversal and frontal planes. MR examination changed the procedure of treatment as a result of larger number and size of metastatic foci found by MRI than by USG. The results of MR examination caused a decrease in the number of patients qualified for liver resection, with a rise in the number of patients referred for PEIT. The application of another diagnostic method (e.g. MR) after USG examination is necessary for patients due for liver resection. MR examination of the liver allows a precise assessment of the operability criteria of hepatic metastases and significantly influences the treatment procedure in patients with metastatic changes in the liver. (author)

Thermodynamic study of the adsorption of chromium ions from aqueous solution on waste corn cobs material

Directory of Open Access Journals (Sweden)

Rafael A. Fonseca-Correa

2014-12-01

Full Text Available The paper shows the results of a study obtaining activated carbon from corn cobs and determining its use as an adsorbent for the removal of Cr3+ from aqueous solutions. The finely ground precursor was subjected to pyrolysis at 600 and 900 °C in a nitrogen atmosphere and chemical activation with H2O2 and HNO3. The effects of pyrolysis conditions and activation method on the physicochemical properties of the materials obtained were tested. The samples were characterised chemically and texturally. Were obtained microporous activated carbons of well-developed surface area varying from 337 to 1213 m2/g and exhibited differences acid-base character of the surface. The results obtained shows that a suitable good option of the activation procedure for corncobs permits the production of economic adsorbents with high sorption capacity for Cr3+ from aqueous solutions. A detailed study of immersion calorimetry was performed with carbons prepared from corn cobs to establish possible relationships with these materials between the enthalpies of immersion and textural and chemical parameters.

Asymptotic procedures for aviation constructions calcul

International Nuclear Information System (INIS)

Zveriaev, E.H.

1994-01-01

Theory of elasticity equations for statics, dynamics, stability of aviation constructions are very complex and very difficult to decide. To get the solution engineers pass on to the applied theories -- ones of bars, plates, shells. In this case some hypothesises are input. A quantity of the ones in vague, and its might be excessive and even contradicting. In this work some procedures permitting to establish the necessary and sufficient quantity of hypothesises, estimating each member contribution into equation, throwing off secondary members and keeping of principals. For example, in such a manner all without exception applied theories of bar, plates and shells are obtained from three-dimensional theory of elasticity. The fact is interesting that all the theories are obtained on a basis of the mapping contracting principle. The proposed approach essence is contained in that some small parametres are singled out of the input equations and the ones are rewritten in the suitable aspect small parametre to the some power value is attached to the symbols of differentiation. This unknown power is determined from the condition of coincidence of the starting approximation, power with the one of the first approximation. As the first example the problem for the unit width long rectangular strip with the fixed short edges (x=1,1) and the free longitudinal edges (y=+1, -1) is considered. The longitudinal edges are loaded with some distributed charge

Formulating a poorly water soluble drug into an oral solution suitable for paediatric patients; lorazepam as a model drug

NARCIS (Netherlands)

A.C. Van Der Vossen (Anna C.); I. Van Der Velde (Iris); O. Smeets (Oscar); Postma, D.J.; Eckhardt, M.; A. Vermes (Andras); B.C.P. Koch (Birgit C. P.); A.G. Vulto (Arnold); L.M. Hanff (Lidwien)

2017-01-01

textabstractIntroduction Many drugs are unavailable in suitable oral paediatric dosage forms, and pharmacists often have to compound drugs to provide paediatric patients with an acceptable formulation in the right dose. Liquid formulations offer the advantage of dosing flexibility and ease of

Validation of EOPs/FRGs Procedures Using LOHS Scenario

International Nuclear Information System (INIS)

Bajs, T.; Konjarek, D.; Vukovic, J.

2012-01-01

Validation of EOPs (Emergency Operating Procedures) and FRGs (Function Restoration Guidelines) can be achieved either through plant full scope simulator or on desk top exercises. The desk top exercise is conducted when for the given scenario plant full scope simulator is not suitable. In either verification cases predefined scenario should be evaluated and possible branching foreseen. The scenario presented is LOHS, with bleed and feed procedure initiated. Best estimate light water reactor transient analysis code RELAP5/mod3.3 was used in calculation. Standardized detailed plant model was used. Operator actions were modelled from beginning of the scenario to its termination.(author).

Environmental control procedures at the Savannah River Plant

International Nuclear Information System (INIS)

Sheldon, E.B.

1975-01-01

New environmental control activities in the past year at SRP have included improved control and reporting procedures for chemical spills, reclamation of high-value scrap from wastes, new disposal methods for solid wastes not suitable for the sanitary landfill, improved oil containment, and reduction of sediment discharges to on-plant streams. Interdepartmental committees provide the primary routes for planning and coordinating environmental protection throughout SRP. An improved site-use coordination procedure, developed and implemented by ERDA-SR, has provided more effective control and communication pertaining to activities of the several organizations actively using the 300-square-mile SRP site. (auth)

Procedure automation: the effect of automated procedure execution on situation awareness and human performance

International Nuclear Information System (INIS)

Andresen, Gisle; Svengren, Haakan; Heimdal, Jan O.; Nilsen, Svein; Hulsund, John-Einar; Bisio, Rossella; Debroise, Xavier

2004-04-01

As advised by the procedure workshop convened in Halden in 2000, the Halden Project conducted an experiment on the effect of automation of Computerised Procedure Systems (CPS) on situation awareness and human performance. The expected outcome of the study was to provide input for guidance on CPS design, and to support the Halden Project's ongoing research on human reliability analysis. The experiment was performed in HAMMLAB using the HAMBO BWR simulator and the COPMA-III CPS. Eight crews of operators from Forsmark 3 and Oskarshamn 3 participated. Three research questions were investigated: 1) Does procedure automation create Out-Of-The-Loop (OOTL) performance problems? 2) Does procedure automation affect situation awareness? 3) Does procedure automation affect crew performance? The independent variable, 'procedure configuration', had four levels: paper procedures, manual CPS, automation with breaks, and full automation. The results showed that the operators experienced OOTL problems in full automation, but that situation awareness and crew performance (response time) were not affected. One possible explanation for this is that the operators monitored the automated procedure execution conscientiously, something which may have prevented the OOTL problems from having negative effects on situation awareness and crew performance. In a debriefing session, the operators clearly expressed their dislike for the full automation condition, but that automation with breaks could be suitable for some tasks. The main reason why the operators did not like the full automation was that they did not feel being in control. A qualitative analysis addressing factors contributing to response time delays revealed that OOTL problems did not seem to cause delays, but that some delays could be explained by the operators having problems with the freeze function of the CPS. Also other factors such as teamwork and operator tendencies were of importance. Several design implications were drawn

Analytic continuation of solutions of some nonlinear convolution partial differential equations

Directory of Open Access Journals (Sweden)

Hidetoshi Tahara

2015-01-01

Full Text Available The paper considers a problem of analytic continuation of solutions of some nonlinear convolution partial differential equations which naturally appear in the summability theory of formal solutions of nonlinear partial differential equations. Under a suitable assumption it is proved that any local holomorphic solution has an analytic extension to a certain sector and its extension has exponential growth when the variable goes to infinity in the sector.

Analgesic techniques in minor painful procedures in neonatal units: a survey in northern Italy.

Science.gov (United States)

Codipietro, Luigi; Bailo, Elena; Nangeroni, Marco; Ponzone, Alberto; Grazia, Giuseppe

2011-01-01

The aim of this survey was to evaluate the current practice regarding pain assessment and pain management strategies adopted in commonly performed minor painful procedures in Northern Italian Neonatal Intensive Care Units (NICUs). A multicenter survey was conducted between 2008 and 2009 in 35 NICUs. The first part of the survey form covered pain assessment tools, the timing of analgesics, and the availability of written guidelines. A second section evaluated the analgesic strategies adopted in commonly performed painful procedures. The listed analgesic procedures were as follows: oral sweet solutions alone, non-nutritive sucking (NNS) alone, a combination of sweet solutions and NNS, breast-feeding where available, and topical anesthetics. Completed questionnaires were returned from 30 neonatal units (85.7% response rate). Ten of the 30 NICUs reported using pain assessment tools for minor invasive procedures. Neonatal Infant Pain Scale was the most frequently used pain scale (60%). Twenty neonatal units had written guidelines directing pain management practices. The most frequently used procedures were pacifiers alone (69%), followed by sweet-tasting solutions (58%). A 5% glucose solution was the most frequently utilized sweet-tasting solution (76.7%). A minority of NICUs (16.7%) administered 12% sucrose solutions for analgesia and the application of topical anesthetics was found in 27% of NICUs while breast-feeding was performed in 7% of NICUs. This study found a low adherence to national and international guidelines for analgesia in minor procedures: the underuse of neonatal pain scales (33%), sucrose solution administration before heel lance (23.3%), topical anesthetics before venipuncture, or other analgesic techniques. The presence of written pain control guidelines in these regions of Northern Italy increased in recent years (from 25% to 66%). © 2010 World Institute of Pain.

Attractor mechanism as a distillation procedure

International Nuclear Information System (INIS)

Levay, Peter; Szalay, Szilard

2010-01-01

In a recent paper it was shown that for double extremal static spherical symmetric BPS black hole solutions in the STU model the well-known process of moduli stabilization at the horizon can be recast in a form of a distillation procedure of a three-qubit entangled state of a Greenberger-Horne-Zeilinger type. By studying the full flow in moduli space in this paper we investigate this distillation procedure in more detail. We introduce a three-qubit state with amplitudes depending on the conserved charges, the warp factor, and the moduli. We show that for the recently discovered non-BPS solutions it is possible to see how the distillation procedure unfolds itself as we approach the horizon. For the non-BPS seed solutions at the asymptotically Minkowski region we are starting with a three-qubit state having seven nonequal nonvanishing amplitudes and finally at the horizon we get a Greenberger-Horne-Zeilinger state with merely four nonvanishing ones with equal magnitudes. The magnitude of the surviving nonvanishing amplitudes is proportional to the macroscopic black hole entropy. A systematic study of such attractor states shows that their properties reflect the structure of the fake superpotential. We also demonstrate that when starting with the very special values for the moduli corresponding to flat directions the uniform structure at the horizon deteriorates due to errors generalizing the usual bit flips acting on the qubits of the attractor states.

Multi-element determination of soil solution by INAA

International Nuclear Information System (INIS)

Qian Qinfang; Wu Shuiqing; Tian Jibing

1992-01-01

One of the factors influencing crop growth is the effective elemental contents, especially trace elements, under the circumstances of the same concentrations of N, P and K in soil. In order to obtain the data of effective elemental contents in soil, a novel method was introduced. In this method, soil solution was extracted by a squeezer. The concentrations of elements in soil solution were determined by INAA. Study on the compositions and the contents of elements in soil solution will provide information on making a suitable soil environment for plant growth and on rational and economical manuring

46 CFR 153.1035 - Acetone cyanohydrin or lactonitrile solutions.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Acetone cyanohydrin or lactonitrile solutions. 153.1035... Special Cargo Procedures § 153.1035 Acetone cyanohydrin or lactonitrile solutions. No person may operate a tankship carrying a cargo of acetone cyanohydrin or lactonitrile solutions, unless that cargo is stabilized...

MITG test procedure and results

International Nuclear Information System (INIS)

Eck, M.E.; Mukunda, M.

1983-01-01

Elements and modules for Radioisotope Thermoelectric Generator have been performance tested since the inception of the RTG program. These test articles seldom resembled flight hardware and often lacked adequate diagnostic instrumentation. Because of this, performance problems were not identified in the early stage of program development. The lack of test data in an unexpected area often hampered the development of a problem solution. A procedure for conducting the MITG Test was developed in an effort to obtain data in a systematic, unambiguous manner. This procedure required the development of extensive data acquisition software and test automation. The development of a facility to implement the test procedure, the facility hardware and software requirements, and the results of the MITG testing are the subject of this paper

Existence of Positive Solutions for Nonlinear Eigenvalue Problems

Directory of Open Access Journals (Sweden)

Fan-Kai Kung

2010-01-01

Full Text Available We use a fixed point theorem in a cone to obtain the existence of positive solutions of the differential equation, u″+λf(t,u=0, 0suitable boundary conditions, where λ is a parameter.

On centralized power pool auction: a novel multipliers stabilization procedure

International Nuclear Information System (INIS)

Jimenez-Redondo, Noemi

2005-01-01

This paper addresses the Short-Term Hydro-Thermal Coordination (STHTC) problem. It is a large-scale, combinatorial and nonlinear optimization problem. It is usually solved using a Lagrangian Relaxation (LR) approach. LR procedure is based on the solution of the dual problem of the original one. The dual problem variables are the Lagrange multipliers. These multipliers have an economic meaning: electric energy hourly prices. This paper focuses on an efficient solution of the dual problem of the STHTC problem. A novel multiplier stabilization technique, which significantly improves the quality of the solution, is presented. The provided method could be the optimization tool used by the Independent System Operator of a centralized Power Pool. The solution procedure diminishes the conflict of interest in determining energy prices. A realistic large-scale case study illustrates the behavior of the presented approach. (Author)

High level waste repository site suitability criteria. Environmental impact statement methodology

International Nuclear Information System (INIS)

1977-06-01

The approach (methodology) which has been developed for the preparation of the environmental impact statement (EIS) is described. A suggested outline is presented for the High Level Waste Repository Site Suitability Criteria EIS together with a detailed description of the approach to be used in preparing the EIS. In addition, a methodology is presented by which the necessary cost/benefit/risk comparisons of alternative sets of site suitability criteria can be made. The TERA environmental research data bank, a computerized data bank which contained information on current and historical licensing activities for power plants was modified to include information on generic or programmatic EIS related issues. The content of the modified data bank was utilized to develop the EIS outline presented in this report. The report recommends that a modified matrix evaluation approach be used to make the cost/benefit/risk comparisons. The suggested matrix is designed to facilitate between criteria comparative analyses of economic, environmental, sociological and radiological risk factors. The quantitative compositing of dollar cost and benefits, environmental and sociological impacts, and radiological risks is to be performed using a semi-analytical, semi-visual procedure based on the concept of ''decision surfaces.''

Suitability of women as candidates for an environmental education program in Pakistan

International Nuclear Information System (INIS)

Asim, A.

2005-01-01

This paper attempts to objectively analyze the suitability of women in the Pakistani Rural sector for a form environmental education program. It commences by giving a brief introduction of the deteriorating and neglected environmental situation in Pakistan. Then it proceeds into monitoring the effect of environmental degradation on women residing in the rural sector. Further the paper attempts to gauge the suitability of these women candidates for an environmental education program. Different factors favoring such a proposal such occupational and household roles and relevance of such an education are discussed, supported by relevant data. All suitability factors are supported with complete implied assistance on the government's part, i.e. provision of all necessary resources for the educational learning to be of any use. Then the paper mentions the various socio-cultural constraints within the society, recommending women to be unsuitable for an environmental education program. Media's role in combating these problems is stressed. The problem of opportunity cost is described another factor making women unsuitable for such a learning program. Solution is proposed in the form granting money to women for attending classes and meetings. It is proposed that this act should not be considered as an expense; rather it should be treated as an investment in a sustainable development process. This paper is finished at a judicial conclusion drawn from both type of arguments presented and studied. (author)

A Web-Based Decision Support System for Evaluating Soil Suitability for Cassava Cultivation

Directory of Open Access Journals (Sweden)

Adewale Opeoluwa Ogunde

2017-01-01

Full Text Available Precision agriculture in recent times had assumed a different dimension in order to improve on the poor standard of agriculture. Similarly, the upsurge in technological advancement, most especially in the aspect of machine learning and artificial intelligence, is a promising trend towards a positive solution to this problem. Therefore, this research work presents a decision support system for analyzing and mining knowledge from soil data with respect to its suitability for cassava cultivation. Past data consisting of some major soil attributes were obtained from relevant literature sources. This data was preprocessed using the ARFF Converter, available in WEKA. 70% of the data were used as training data set while remaining 30% were used for testing. Classification rule mining was carried out using J48 decision tree algorithm for the data training. ‘If-then’ construct models were then generated from the decision tree, which was used to develop a system for predicting the suitability status of soil for cassava cultivation. The percentage accuracy of the data classification was 76.5% and 23.5% for correctly classified and incorrectly classified instances respectively. Practically, the developed system was esteemed a prospective tool for farmers, soil laboratories and other users in predicting soil suitability for cassava cultivation.

Analysis of the magnetohydrodynamic equations and study of the nonlinear solution bifurcations

International Nuclear Information System (INIS)

Morros Tosas, J.

1989-01-01

The nonlinear problems related to the plasma magnetohydrodynamic instabilities are studied. A bifurcation theory is applied and a general magnetohydrodynamic equation is proposed. Scalar functions, a steady magnetic field and a new equation for the velocity field are taken into account. A method allowing the obtention of suitable reduced equations for the instabilities study is described. Toroidal and cylindrical configuration plasmas are studied. In the cylindrical configuration case, analytical calculations are performed and two steady bifurcated solutions are found. In the toroidal configuration case, a suitable reduced equation system is obtained; a qualitative approach of a steady solution bifurcation on a toroidal Kink type geometry is carried out [fr

Slingram EMI prospection: Are vertical orientated devices a suitable solution in archaeological and pedological prospection?

Science.gov (United States)

Thiesson, Julien; Rousselle, Gabrielle; Simon, François Xavier; Tabbagh, Alain

2011-12-01

Electromagnetic induction (EMI) is one of the geophysical techniques widely used in soil studies, the slingram devices being held horizontally over the soil surface, i.e. with the coils located at the same height above the ground surface. Our study aims assessing the abilities of slingram devices when held vertically. 1D and 3D modelling have been achieved in order to compare the theoretical responses of vertical devices to the horizontal ones. Some comparative surveys were also undertaken in archaeological contexts to confirm the reliability of theoretical conclusions. Both approaches show that vertical slingram devices are suitable for survey and can constitute an alternative to the usual horizontal orientation. We give a table in Appendix A which contains the calibration coefficient allowing transforming of the values given by some of commercially available devices which would be advantageous to use in vertical orientation

Choosing a suitable sample size in descriptive sampling

International Nuclear Information System (INIS)

Lee, Yong Kyun; Choi, Dong Hoon; Cha, Kyung Joon

2010-01-01

Descriptive sampling (DS) is an alternative to crude Monte Carlo sampling (CMCS) in finding solutions to structural reliability problems. It is known to be an effective sampling method in approximating the distribution of a random variable because it uses the deterministic selection of sample values and their random permutation,. However, because this method is difficult to apply to complex simulations, the sample size is occasionally determined without thorough consideration. Input sample variability may cause the sample size to change between runs, leading to poor simulation results. This paper proposes a numerical method for choosing a suitable sample size for use in DS. Using this method, one can estimate a more accurate probability of failure in a reliability problem while running a minimal number of simulations. The method is then applied to several examples and compared with CMCS and conventional DS to validate its usefulness and efficiency

Renormalization group equation and scaling solutions for f(R) gravity in exponential parametrization

International Nuclear Information System (INIS)

Ohta, Nobuyoshi; Percacci, Roberto; Vacca, Gian Paolo

2016-01-01

We employ the exponential parametrization of the metric and a ''physical'' gauge fixing procedure to write a functional flow equation for the gravitational effective average action in an f(R) truncation. The background metric is a four-sphere and the coarse-graining procedure contains three free parameters. We look for scaling solutions, i.e. non-Gaussian fixed points for the function f. For a discrete set of values of the parameters, we find simple global solutions of quadratic polynomial form. For other values, global solutions can be found numerically. Such solutions can be extended in certain regions of parameter space and have two relevant directions. We discuss the merits and the shortcomings of this procedure. (orig.)

Quasivariational Solutions for First Order Quasilinear Equations with Gradient Constraint

Science.gov (United States)

Rodrigues, José Francisco; Santos, Lisa

2012-08-01

We prove the existence of solutions for a quasi-variational inequality of evolution with a first order quasilinear operator and a variable convex set which is characterized by a constraint on the absolute value of the gradient that depends on the solution itself. The only required assumption on the nonlinearity of this constraint is its continuity and positivity. The method relies on an appropriate parabolic regularization and suitable a priori estimates. We also obtain the existence of stationary solutions by studying the asymptotic behaviour in time. In the variational case, corresponding to a constraint independent of the solution, we also give uniqueness results.

Calculation of piping loads due to filling procedures

International Nuclear Information System (INIS)

Swidersky, Harald; Thiele, Thomas

2012-01-01

Filling procedures in piping systems are usually not load cases that are studied by fluid dynamic and structure dynamic analyses with respect to the integrity of pipes and supports. Although, their frequency is higher than that of postulated accidental transients, therefore they have to be considered for fatigue analyses. The piping and support loads due to filling procedures are caused by the density differences if the transported fluids, for instance in flows with the transport of gas bubbles. The impact duration of the momentum forces is defined by the flow velocity and the length of discontinuities in the piping segments. Filling procedures end very often with a shock pressure, caused by the impact and decelerating of the fluid front at smaller cross sections. The suitability of the thermally hydraulics program RELAP/MOD3.3 for the calculation of realistic loads from filling procedures was studied, the results compared with experimental data. It is shown that dependent on the discretization level the loads are partial significantly underestimated.

Solution of the mathematical adjoint equations for an interface current nodal formulation

International Nuclear Information System (INIS)

Yang, W.S.; Taiwo, T.A.; Khalil, H.

1994-01-01

Two techniques for solving the mathematical adjoint equations of an interface current nodal method are described. These techniques are the ''similarity transformation'' procedure and a direct solution scheme. A theoretical basis is provided for the similarity transformation procedure originally proposed by Lawrence. It is shown that the matrices associated with the mathematical and physical adjoint equations are similar to each other for the flat transverse leakage approximation but not for the quadratic leakage approximation. It is also shown that a good approximate solution of the mathematical adjoint for the quadratic transverse leakage approximation is obtained by applying the similarity transformation for the flat transverse leakage approximation to the physical adjoint solution. The direct solution scheme, which was developed as an alternative to the similarity transformation procedure, yields the correct mathematical adjoint solution for both flat and quadratic transverse leakage approximations. In this scheme, adjoint nodal equations are cast in a form very similar to that of the forward equations by employing a linear transformation of the adjoint partial currents. This enables the use of the forward solution algorithm with only minor modifications for solving the mathematical adjoint equations. By using the direct solution scheme as a reference method, it is shown that while the results computed with the similarity transformation procedure are approximate, they are sufficiently accurate for calculations of global and local reactivity changes resulting from coolant voiding in a liquid-metal reactor

Recent developments in MrBUMP: better search-model preparation, graphical interaction with search models, and solution improvement and assessment.

Science.gov (United States)

Keegan, Ronan M; McNicholas, Stuart J; Thomas, Jens M H; Simpkin, Adam J; Simkovic, Felix; Uski, Ville; Ballard, Charles C; Winn, Martyn D; Wilson, Keith S; Rigden, Daniel J

2018-03-01

Increasing sophistication in molecular-replacement (MR) software and the rapid expansion of the PDB in recent years have allowed the technique to become the dominant method for determining the phases of a target structure in macromolecular X-ray crystallography. In addition, improvements in bioinformatic techniques for finding suitable homologous structures for use as MR search models, combined with developments in refinement and model-building techniques, have pushed the applicability of MR to lower sequence identities and made weak MR solutions more amenable to refinement and improvement. MrBUMP is a CCP4 pipeline which automates all stages of the MR procedure. Its scope covers everything from the sourcing and preparation of suitable search models right through to rebuilding of the positioned search model. Recent improvements to the pipeline include the adoption of more sensitive bioinformatic tools for sourcing search models, enhanced model-preparation techniques including better ensembling of homologues, and the use of phase improvement and model building on the resulting solution. The pipeline has also been deployed as an online service through CCP4 online, which allows its users to exploit large bioinformatic databases and coarse-grained parallelism to speed up the determination of a possible solution. Finally, the molecular-graphics application CCP4mg has been combined with MrBUMP to provide an interactive visual aid to the user during the process of selecting and manipulating search models for use in MR. Here, these developments in MrBUMP are described with a case study to explore how some of the enhancements to the pipeline and to CCP4mg can help to solve a difficult case.

Small-scale engagement model with arrivals: analytical solutions

International Nuclear Information System (INIS)

Engi, D.

1977-04-01

This report presents an analytical model of small-scale battles. The specific impetus for this effort was provided by a need to characterize hypothetical battles between guards at a nuclear facility and their potential adversaries. The solution procedure can be used to find measures of a number of critical parameters; for example, the win probabilities and the expected duration of the battle. Numerical solutions are obtainable if the total number of individual combatants on the opposing sides is less than 10. For smaller force size battles, with one or two combatants on each side, symbolic solutions can be found. The symbolic solutions express the output parameters abstractly in terms of symbolic representations of the input parameters while the numerical solutions are expressed as numerical values. The input parameters are derived from the probability distributions of the attrition and arrival processes. The solution procedure reduces to solving sets of linear equations that have been constructed from the input parameters. The approach presented in this report does not address the problems associated with measuring the inputs. Rather, this report attempts to establish a relatively simple structure within which small-scale battles can be studied

Solidification of radioactive waste solutions by pelletization technique

International Nuclear Information System (INIS)

Akbar, A.H.; Koester, R.; Rudolph, G.

1980-04-01

A possible way of performing the cement fixation of radioactive wastes is the incorporation into cement pellets on a pan pelletizer, followed by embedding the pellets into an inactive cement matrix. This procedure is suitable for various types of waste, particularly for medium level liquid wastes, and can be used both at drum disposal and at in-situ solidification. This report describes some initial studies on the pelletization technique using a laboratory pelletizer. Formation and size of the pellets have been found to be determined by speed, angle, and load of the pan, ratio and mode of addition of the liquid and solid components, ect. Pellets in various compositions have been produced from cement and water or simulated waste solution, in some cases with the addition of bentonite for improving cesium retention. Some mechanical properties of the pellets such as fall height of fresh pellets, development of hardness (crush test), impact and abrasion resistance, have been determined. Some preliminary experiments were done on backfilling the void space between the pellets - about 40 per cent of the bulk volume - with cement grouts of appropriate compositions. (orig.) [de

Fully implicit, coupled procedures in computational fluid dynamics an engineer's resource book

CERN Document Server

Mazhar, Zeka

2016-01-01

This book introduces a new generation of superfast algorithms for the treatment of the notoriously difficult velocity-pressure coupling problem in incompressible fluid flow solutions. It provides all the necessary details for the understanding and implementation of the procedures. The derivation and construction of the fully-implicit, block-coupled, incomplete decomposition mechanism are given in a systematic, but easy fashion. Worked-out solutions are included, with comparisons and discussions. A complete program code is included for faster implementation of the algorithm. A brief literature review of the development of the classical solution procedures is included as well. .

Suitability of digital camcorders for virtual reality image data capture

Science.gov (United States)

D'Apuzzo, Nicola; Maas, Hans-Gerd

1998-12-01

Today's consumer market digital camcorders offer features which make them appear quite interesting devices for virtual reality data capture. The paper compares a digital camcorder with an analogue camcorder and a machine vision type CCD camera and discusses the suitability of these three cameras for virtual reality applications. Besides the discussion of technical features of the cameras, this includes a detailed accuracy test in order to define the range of applications. In combination with the cameras, three different framegrabbers are tested. The geometric accuracy potential of all three cameras turned out to be surprisingly large, and no problems were noticed in the radiometric performance. On the other hand, some disadvantages have to be reported: from the photogrammetrists point of view, the major disadvantage of most camcorders is the missing possibility to synchronize multiple devices, limiting the suitability for 3-D motion data capture. Moreover, the standard video format contains interlacing, which is also undesirable for all applications dealing with moving objects or moving cameras. Further disadvantages are computer interfaces with functionality, which is still suboptimal. While custom-made solutions to these problems are probably rather expensive (and will make potential users turn back to machine vision like equipment), this functionality could probably be included by the manufacturers at almost zero cost.

A Bidirectional Resonant DC-DC Converter Suitable for Wide Voltage Gain Range

DEFF Research Database (Denmark)

Shen, Yanfeng; Wang, Huai; Al-Durra, Ahmed

2018-01-01

This paper proposes a new bidirectional resonant dc-dc converter suitable for wide voltage gain range applications (e.g., energy storage systems). The proposed converter overcomes the narrow voltage gain range of conventional resonant dc-dc converters, and meanwhile achieves high efficiency...... losses. The operation principles and characteristics of the proposed converter are firstly analyzed in this paper. Then the analytical solutions for the voltage gain, soft-switching, and rms currents are derived, which facilitates the parameters design and optimization. Finally, the proposed topology...... and analysis are verified with experimental results obtained from a 1-kW converter prototype....

Determining roof surfaces suitable for the installation of PV (photovoltaic) systems, based on LiDAR (Light Detection And Ranging) data, pyranometer measurements, and distribution network configuration

International Nuclear Information System (INIS)

Srećković, Nevena; Lukač, Niko; Žalik, Borut; Štumberger, Gorazd

2016-01-01

Proliferation of distributed generation units, integrated within the distribution network requires increased attention to their proper placements. In urban areas, buildings' rooftops are expected to have greater involvement in the deployment of PV (photovoltaic) systems. This paper proposes a novel procedure for determining roof surfaces suitable for their installation. The PV potential of roof surfaces is assessed based on Light Detection And Ranging (LiDAR) data and pyranometer measurements. Then, the time-dependent PV generation profiles, electricity distribution network configuration, and time-dependent loading profiles are used together over time-steps for selecting those roof surfaces with the highest PV potential, which would lead to the highest reduction of network losses per year. The presented procedure was implemented within a real urban area distribution network. The results obtained confirmed that PV potential assessment could be an insufficient criterion when selecting those roof surfaces suitable for the installation of PV systems. In order to obtain relevant results, network configuration and time-dependent loading and generation profiles must be considered as well. - Highlights: • Roof surfaces, suitable for installation of PV systems are evaluated and ranked. • Improved PV potential based procedure is proposed for their selection in urban areas. • Time-dependent network loading and PV generation profiles are considered. • Losses in a real electricity network are minimized in the optimization procedure. • Final selection of ranked roof surfaces is based on results of optimization.

Towards an integrated quality control procedure for eddy-covariance data

Science.gov (United States)

Vitale, Domenico; Papale, Dario

2017-04-01

The eddy-covariance technique is nowadays the most reliable and direct way, allowing to calculate the main fluxes of Sensible and Latent Heat and of Net Ecosystem Exchange, this last being the result of the difference between the CO2 assimilated by photosynthetic activities and those released to the atmosphere through the ecosystem respiration processes. Despite the improvements in accuracy of measurement instruments and software development, the eddy-covariance technique is not suitable under non-ideal conditions respect to the instruments characteristics and the physical assumption behind the technique mainly related to the well-developed and stationary turbulence conditions. Under these conditions the calculated fluxes are not reliable and need to be flagged and discarded. In order to discover these unavoidable "bad" fluxes and build dataset with the highest quality, several tests applied both on high-frequency (10-20 Hz) raw data and on half-hourly times series have been developed in the past years. Nevertheless, there is an increasing need to develop a standardized quality control procedure suitable not only for the analysis of long-term data, but also for the near-real time data processing. In this paper, we review established quality assessment procedures and present an innovative quality control strategy with the purpose of integrating the existing consolidated procedures with robust and advanced statistical tests more suitable for the analysis of time series data. The performance of the proposed quality control strategy is evaluated both on simulated and EC data distributed by the ICOS research infrastructure. It is concluded that the proposed strategy is able to flag and exclude unrealistic fluxes while being reproducible and retaining the largest possible amount of high quality data.

Analytical Solution of Multicompartment Solute Kinetics for Hemodialysis

Directory of Open Access Journals (Sweden)

Przemysław Korohoda

2013-01-01

Full Text Available Objective. To provide an exact solution for variable-volume multicompartment kinetic models with linear volume change, and to apply this solution to a 4-compartment diffusion-adjusted regional blood flow model for both urea and creatinine kinetics in hemodialysis. Methods. A matrix-based approach applicable to linear models encompassing any number of compartments is presented. The procedure requires the inversion of a square matrix and the computation of its eigenvalues λ, assuming they are all distinct. This novel approach bypasses the evaluation of the definite integral to solve the inhomogeneous ordinary differential equation. Results. For urea two out of four eigenvalues describing the changes of concentrations in time are about 105 times larger than the other eigenvalues indicating that the 4-compartment model essentially reduces to the 2-compartment regional blood flow model. In case of creatinine, however, the distribution of eigenvalues is more balanced (a factor of 102 between the largest and the smallest eigenvalue indicating that all four compartments contribute to creatinine kinetics in hemodialysis. Interpretation. Apart from providing an exact analytic solution for practical applications such as the identification of relevant model and treatment parameters, the matrix-based approach reveals characteristic details on model symmetry and complexity for different solutes.

Land Suitability Assessment And Precision Farming Prospects For ...

African Journals Online (AJOL)

The soils on the farm were sampled and profiles classified using South African Binomial system of soil classification. The farm was divided into suitability classes of highly suitable (S1), suitable (S2), and unsuitable (N1), and permanently unsuitable (N2) classes. Maize-soybean suitability maps were produced based on soil ...

A Rapid Selection Procedure for Simple Commercial Implementation of omega-Transaminase Reactions

DEFF Research Database (Denmark)

Gundersen Deslauriers, Maria; Tufvesson, Pär; Rackham, Emma J.

2016-01-01

A stepwise selection procedure is presented to quickly evaluate whether a given omega-transaminase reaction is suitable for a so-called "simple" scale-up for fast industrial implementation. Here "simple" is defined as a system without the need for extensive process development or specialized......, and (3) determination of product inhibition. The method is exemplified with experimental work focused on two products: 1-(4-bromophenyl)ethylamine and (S)-(+)3-amino-1-Boc-piperidine, synthesized from their corresponding pro-chiral ketones each with two alternative amine donors, propan-2-amine, and 1......-phenylethylamine. Each step of the method has a threshold value, which must be surpassed to allow "simple" implementation, helping select suitable combinations of substrates, enzymes, and donors. One reaction pair, 1-Boc-3-piperidone with propan-2-amine, met the criteria of the three-step selection procedure...

Image-guided procedures in brain biopsy.

Science.gov (United States)

Fujita, K; Yanaka, K; Meguro, K; Narushima, K; Iguchi, M; Nakai, Y; Nose, T

1999-07-01

Image-guided procedures, such as computed tomography (CT)-guided stereotactic and ultrasound-guided methods, can assist neurosurgeons in localizing the relevant pathology. The characteristics of image-guided procedures are important for their appropriate use, especially in brain biopsy. This study reviewed the results of various image-guided brain biopsies to ascertain the advantages and disadvantages. Brain biopsies assisted by CT-guided stereotactic, ultrasound-guided, Neuronavigator-guided, and the combination of ultrasound and Neuronavigator-guided procedures were carried out in seven, eight, one, and three patients, respectively. Four patients underwent open biopsy without a guiding system. Twenty of 23 patients had a satisfactory diagnosis after the initial biopsy. Three patients failed to have a definitive diagnosis after the initial procedure, one due to insufficient volume sampling after CT-guided procedure, and two due to localization failure by ultrasound because the lesions were nonechogenic. All patients who underwent biopsy using the combination of ultrasound and Neuronavigator-guided methods had a satisfactory result. The CT-guided procedure provided an efficient method of approaching any intracranial target and was appropriate for the diagnosis of hypodense lesions, but tissue sampling was sometimes not sufficient to achieve a satisfactory diagnosis. The ultrasound-guided procedure was suitable for the investigation of hyperdense lesions, but was difficult to localize nonechogenic lesions. The combination of ultrasound and Neuronavigator methods improved the diagnostic accuracy even in nonechogenic lesions such as malignant lymphoma. Therefore, it is essential to choose the most appropriate guiding method for brain biopsy according to the radiological nature of the lesions.

The development of rock suitability classification strategies in the Finnish spent nuclear fuel disposal program

International Nuclear Information System (INIS)

Hellae, Pirjo; Hagros, Annika; Aaltonen, Ismo; Kosunen, Paula; Mattila, Jussi

2015-01-01

This paper describes the development of the rock suitability classification strategies applied to locate the spent fuel repository in crystalline rock in Finland. Development of the classification procedure is motivated not only by the regulatory requirements, but also by the need to more closely integrate site characterization, repository design and long-term safety assessment. The classification procedure has been developed along with the increasing level of detail of the available site data and knowledge on the performance of the engineered barrier system (EBS). The classification system has also been adapted to the changes in the regulations. The present form of the classification system and experiences from testing the system at the site are described. Demonstration activities have shown that the criteria and the stepwise research, construction and decision making protocol can be applied successfully.

The development of rock suitability classification strategies in the Finnish spent nuclear fuel disposal program

Energy Technology Data Exchange (ETDEWEB)

Hellae, Pirjo; Hagros, Annika [Saanio and Riekkola Oy (Finland); Aaltonen, Ismo; Kosunen, Paula; Mattila, Jussi [Posiva Oy (Finland)

2015-07-01

This paper describes the development of the rock suitability classification strategies applied to locate the spent fuel repository in crystalline rock in Finland. Development of the classification procedure is motivated not only by the regulatory requirements, but also by the need to more closely integrate site characterization, repository design and long-term safety assessment. The classification procedure has been developed along with the increasing level of detail of the available site data and knowledge on the performance of the engineered barrier system (EBS). The classification system has also been adapted to the changes in the regulations. The present form of the classification system and experiences from testing the system at the site are described. Demonstration activities have shown that the criteria and the stepwise research, construction and decision making protocol can be applied successfully.

Solution Path for Pin-SVM Classifiers With Positive and Negative $\\tau $ Values.

Science.gov (United States)

Huang, Xiaolin; Shi, Lei; Suykens, Johan A K

2017-07-01

Applying the pinball loss in a support vector machine (SVM) classifier results in pin-SVM. The pinball loss is characterized by a parameter τ . Its value is related to the quantile level and different τ values are suitable for different problems. In this paper, we establish an algorithm to find the entire solution path for pin-SVM with different τ values. This algorithm is based on the fact that the optimal solution to pin-SVM is continuous and piecewise linear with respect to τ . We also show that the nonnegativity constraint on τ is not necessary, i.e., τ can be extended to negative values. First, in some applications, a negative τ leads to better accuracy. Second, τ = -1 corresponds to a simple solution that links SVM and the classical kernel rule. The solution for τ = -1 can be obtained directly and then be used as a starting point of the solution path. The proposed method efficiently traverses τ values through the solution path, and then achieves good performance by a suitable τ . In particular, τ = 0 corresponds to C-SVM, meaning that the traversal algorithm can output a result at least as good as C-SVM with respect to validation error.

A rapid sample decomposition procedure for bromo-heavies containing ferruginous material: determination of REEs and thorium by ICP-AES

International Nuclear Information System (INIS)

Khorge, C.R.; Murugesan, P.; Chakrapani, G.

2013-01-01

A rapid method of sample decomposition and dissolution for bromoform heavies is described for the determination of REEs and thorium by inductively coupled plasma- optical emission spectrometry. For application to geochemical exploration to achieve the high sample throughput; a simple and rapid analytical procedure is a prerequisite. In order to speed-up the existing methodology, phosphate fusion was introduced for decomposition of samples. In the proposed method, bromoform-heavies material are fused with 1:1 mixture of sodium dihydrogen orthophosphate and tetra-sodium pyrophosphate and dissolved in distilled water. After disintegration of melt, the solution was subjected to oxalate precipitation followed by R 2 O 3 separation for separating the REEs from major matrix interfering elements. The rare earth elements and thorium in the resultant solution were determined by ICP-OES. The results are compared with the results obtained by well-established existing dissolution procedures involving HF-HCl-HClO 4 acid treatment and NaF/KHF 2 fusion followed by H 2 SO 4 acid fuming. The accuracy of the method was evaluated by doping the phosphate blank with known amount of REEs and comparing the recoveries obtained using the present method. The method is simple, rapid and is suitable for the routine determination of REEs and Th in bromoform-heavies. The RSD of the method was found to be within 1-3% for Th and REEs by ICP-AES. (author)

Numerical method for solution of transient, homogeneous, equilibrium, two-phase flows in one space dimension

International Nuclear Information System (INIS)

Shin, Y.W.; Wiedermann, A.H.

1979-10-01

A solution method is presented for transient, homogeneous, equilibrium, two-phase flows of a single-component fluid in one space dimension. The method combines a direct finite-difference procedure and the method of characteristics. The finite-difference procedure solves the interior points of the computing domain; the boundary information is provided by a separate procedure based on the characteristics theory. The solution procedure for boundary points requires information in addition to the physical boundary conditions. This additional information is obtained by a new procedure involving integration of characteristics in the hodograph plane. Sample problems involving various combinations of basic boundary types are calculated for two-phase water/steam mixtures and single-phase nitrogen gas, and compared with independent method-of-characteristics solutions using very fine characteristic mesh. In all cases, excellent agreement is demonstrated

Construct validation of teacher portfolio assessment : Procedures for improving teacher competence assessment illustrated by teaching students research skills

NARCIS (Netherlands)

Schaaf, M.F. van der

2005-01-01

The study aims to design and test procedures for teacher portfolio assessments. What are suitable procedures to assess teachers' competencies in developing students' research skills? We first searched into the tasks teachers have in teaching students research skills and the competencies needed to

Gadolinium Use in Spine Pain Management Procedures for Patients with Contrast Allergies: Results in 527 Procedures

International Nuclear Information System (INIS)

Safriel, Yair; Ang, Roberto; Ali, Muhammed

2008-01-01

Introduction. To review the safety and efficacy of gadolinium in spine pain management procedures in patients at high risk for a contrast reaction and who are not suitable candidates for the use of standard non-ionic contrast. Methods. We reviewed records over a 61-month period of all image-guided spinal pain management procedures where patients had allergies making them unsuitable candidates for standard non-ionic contrast and where gadolinium was used to confirm needle tip placement prior to injection of medication. Results. Three hundred and four outpatients underwent 527 procedures. A spinal needle was used in all but 41 procedures. Gadolinium was visualized using portable C-arm fluoroscopy in vivo allowing for confirmation of needle tip location. The gadolinium dose ranged from 0.2 to 10 ml per level. The highest dose received by one patient was 15.83 ml intradiscally during a three-level discogram. Three hundred and one patients were discharged without complication or known delayed complications. One patient had documented intrathecal injection but without sequelae and 2 patients who underwent cervical procedures experienced seizures requiring admission to the intensive care unit. Both the latter patients were discharged without any further complications. Conclusion. Based on our experience we recommend using gadolinium judiciously for needle tip confirmation. We feel more confident using gadolinium in the lumbar spine and in cervical nerve blocks. Gadolinium should probably not be used as an injectate volume expander. The indications for gadolinium use in cervical needle-guided spine procedures are less clear and use of a blunt-tipped needle should be considered

A 3-D model of superfluid helium suitable for numerical analysis

CERN Document Server

Darve, C; Van Sciver, S W

2009-01-01

The two-fluid description is a very successful phenomenological representation of the properties of Helium II. A 3-D model suitable for numerical analysis based on the Landau-Khalatnikov description of Helium II is proposed. In this paper we introduce a system of partial differential equations that is both complete and consistent as well as practical, to be used for a 3-D solution of the flow of Helium II. The development of a 3-D numerical model for Helium II is motivated by the need to validate experimental results obtained by observing the normal component velocity distribution in a Helium II thermal counter-flow using the Particle Image Velocimetry (PIV) technique.

Preparation standardisation and use of plutonium nitrate reference solutions

International Nuclear Information System (INIS)

Brown, M.L.; Drummond, J.L.

1981-07-01

A procedure is described for the purification of a plutonium nitrate solution in nitric acid for use as a plutonium master standard. Anion exchange chromatography followed by oxalate precipitation is used to purify the plutonium and the residual cationic impurities are analysed by emission spectroscopy. The plutonium content is accurately and precisely measured by two independent methods, namely by gravimetry as PuO 2 at 1250 0 C and by ceric oxidation, ferrous reduction and dichromate titration. Full details of the purification procedure are given, with recommended methods for storing and using the standard solution. It is concluded that such a solution is the most satisfactory reference material, available for plutonium analysis for reprocessing plants, and is adequately related to other, internationally accepted, standard reference materials. (author)

Comprehensive environment-suitability evaluation model about Carya cathayensis

International Nuclear Information System (INIS)

Da-Sheng, W.; Li-Juan, L.; Qin-Fen, Y.

2013-01-01

On the relation between the suitable environment and the distribution areas of Carya cathayensis Sarg., the current studies are mainly committed to qualitative descriptions, but did not consider quantitative models. The objective of this study was to establish a environment-suitability evaluation model which used to predict potential suitable areas of C. cathayensis. Firstly, the 3 factor data of soil type, soil parent material and soil thickness were obtained based on 2-class forest resource survey, and other factor data, which included elevation, slope, aspect, surface curvature, humidity index, and solar radiation index, were extracted from DEM (Digital Elevation Model). Additionally, the key affecting factors were defined by PCA (Principal Component Analysis), the weights of evaluation factors were determined by AHP (Analysis Hierarchy Process) and the quantitative classification of single factor was determined by membership function with fuzzy mathematics. Finally, a comprehensive environment-suitability evaluation model was established and which was also used to predict the potential suitable areas of C. cathayensis in Daoshi Town in the study region. The results showed that 85.6% of actual distribution areas were in the most suitable and more suitable regions and 11.5% in the general suitable regions

Novel Hyperbolic Homoclinic Solutions of the Helmholtz-Duffing Oscillators

Directory of Open Access Journals (Sweden)

Yang-Yang Chen

2016-01-01

Full Text Available The exact and explicit homoclinic solution of the undamped Helmholtz-Duffing oscillator is derived by a presented hyperbolic function balance procedure. The homoclinic solution of the self-excited Helmholtz-Duffing oscillator can also be obtained by an extended hyperbolic perturbation method. The application of the present homoclinic solutions to the chaos prediction of the nonautonomous Helmholtz-Duffing oscillator is performed. Effectiveness and advantage of the present solutions are shown by comparisons.

The use of potassium hydroxide (KOH) solution as a suitable approach to isolate plastics ingested by marine organisms.

Science.gov (United States)

Kühn, Susanne; van Werven, Bernike; van Oyen, Albert; Meijboom, André; Bravo Rebolledo, Elisa L; van Franeker, Jan A

2017-02-15

In studies of plastic ingestion by marine wildlife, visual separation of plastic particles from gastrointestinal tracts or their dietary content can be challenging. Earlier studies have used solutions to dissolve organic materials leaving synthetic particles unaffected. However, insufficient tests have been conducted to ensure that different categories of consumer products partly degraded in the environment and/or in gastrointestinal tracts were not affected. In this study 63 synthetic materials and 11 other dietary items and non-plastic marine debris were tested. Irrespective of shape or preceding environmental history, most polymers resisted potassium hydroxide (KOH) solution, with the exceptions of cellulose acetate from cigarette filters, some biodegradable plastics and a single polyethylene sheet. Exposure of hard diet components and other marine debris showed variable results. In conclusion, the results confirm that usage of KOH solutions can be a useful approach in general quantitative studies of plastic ingestion by marine wildlife. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Land suitability maps for waste disposal siting

International Nuclear Information System (INIS)

Hrasna, M.

1996-01-01

The suitability of geoenvironment for waste disposal depends mainly on its stability and on the danger of groundwater pollution. Besides them, on the land suitability maps for the given purpose also those factors of the factors of the geoenvironment and the landscape should be taken into account, which enable another way of the land use, such as mineral resources, water resources, fertile soils, nature reserves, etc. On the base of the relevant factors influence evaluation - suitable, moderately suitable and unsuitable territorial units are delimited on the maps. The different way of various scale maps compilation is applied, taken into account their different representing feasibilities. (authors)

Evaluation of Hands-Free Devices for the Display of Maintenance Procedures

Science.gov (United States)

Whitmore, Mihriban; Hoffman, Ronald B.; Litaker, Harry, Jr.; Solem, Jody; Holden, Kritina; Twyford, Evan; Conlee, Carl

2007-01-01

Over the past year, NASA's focus has turned to crewed long duration and exploration missions. On these journeys, crewmembers will be required to execute thousands of procedures to maintain life support systems, check out space suits, conduct science experiments, and perform medical exams. To support the many complex tasks crewmembers undertake in microgravity, NASA is interested in providing crewmembers a hands-free work environment to promote more efficient operations. The overarching objective is to allow crewmembers to use both of their hands for tasks related to their mission, versus holding a paper manual or interacting with a display. The use of advanced, hands-free tools will undoubtedly make the crewmembers task easier, but they can also add to overall task complexity if not properly designed. A leading candidate technology for supporting a hands-free environment is the Head-Mounted Display (HMD). A more recent technology (e-book reader) that could be easily temp-stowed near the work area is also a potential hands-free solution. Previous work at NASA involved the evaluation of several commercially available HMDs for visual quality, comfort, and fit, as well as suitability for use in microgravity. Based on results from this work, three HMDs were selected for further evaluation (along with an e-book reader), using International Space Station (ISS)-like maintenance procedures. Two evaluations were conducted in the Space Station Mockup and Trainer Facility (SSMTF) located at the NASA Johnson Space Center (building 9). The SSMTF is a full scale, medium fidelity replica of the pressurized portions of the ISS. It supports crew training such as ingress and egress, habitability, and emergency procedures. In each of the two evaluations, the participants performed two maintenance procedures. One maintenance procedure involved inspecting air filters in a life support system and replacing them with a clean filter if one were found to be contaminated. The second

Asymptotic Behavior of Periodic Wave Solution to the Hirota—Satsuma Equation

International Nuclear Information System (INIS)

Wu Yong-Qi

2011-01-01

The one- and two-periodic wave solutions for the Hirota—Satsuma (HS) equation are presented by using the Hirota derivative and Riemann theta function. The rigorous proofs on asymptotic behaviors of these two solutions are given such that soliton solution can be obtained from the periodic wave solution in an appropriate limiting procedure. (general)

Negotiated Crime Solutions in Portuguese Law: A nowadays reality in a far-away galaxy?

Directory of Open Access Journals (Sweden)

André Ferreira de Oliveira

2017-03-01

Full Text Available The ideas of procedural consensus and celerity increasingly shape the Criminal Procedural Law of Democratic countries. Negotiated criminal justice solutions have been multiplying in the last years, posing a multiplicity of challenges to the pure and traditional procedural doctrine, to the rights traditionally assured to the procedural actors, being important to question if the (even more organized criminality and the transnational and technological methods of crime did not shift the center of the confrontation between the efficient administration of justice and the rights of the accused. The Portuguese Republic is no exception: without a legislative framework explicitly guarantying a way to benefit those who collaborate with Justice, one must first question if the Criminal Procedural Code allows or may allow criminal Justice negotiated solutions; we will analyze some foreseen legal solutions of consensualism, not forgeting the Portuguese doctrine and courts decisions.

On solution of Maxwell's equations in axisymmetric domains with edges. Part I: Theoretical aspects

International Nuclear Information System (INIS)

Nkemzi, Boniface

2003-10-01

In this paper we present the basic mathematical tools for treating boundary value problems for the Maxwell's equations in three-dimensional axisymmetric domains with reentrant edges by means of partial Fourier analysis. We consider the decomposition of the classical and regularized time-harmonic three-dimensional Maxwell's equations into variational equations in the plane meridian domain of the axisymmetric domain and define suitable weighted Sobolev spaces for their treatment. The trace properties of these spaces on the rotational axis and some properties of the solutions are proved, which are important for further numerical treatment, e.g. by the finite-element method. Particularly, a priori estimates of the solutions of the reduced system are given and the asymptotic behavior of these solutions near reentrant corners of the meridian domain is explicitly described by suitable singular functions. (author)

Evaluation of poly (aspartic acid sodium salt) as a draw solute for forward osmosis.

Science.gov (United States)

Gwak, Gimun; Jung, Bokyung; Han, Sungsoo; Hong, Seungkwan

2015-09-01

Poly (aspartic acid sodium salt) (PAspNa) was evaluated for its potential as a novel draw solute in forward osmosis (FO). The inherent advantages of PAspNa, such as good water solubility, high osmotic pressure, and nontoxicity, were first examined through a series of physicochemical analyses and atomic-scale molecular dynamics simulations. Then, lab-scale FO tests were performed to evaluate its suitability in practical processes. Compared to other conventional inorganic solutes, PAspNa showed comparable water flux but significantly lower reverse solute flux, demonstrating its suitability as a draw solute. Moreover, fouling experiments using synthetic wastewater as a feed solution demonstrated that PAspNa reversely flowed to the feed side reduced inorganic scaling on the membrane active layer. The recyclability of PAspNa was studied using both nanofiltration (NF) and membrane distillation (MD) processes, and the results exhibited its ease of recovery. This research reported the feasibility and applicability of FO-NF or FO-MD processes using PAspNa for wastewater reclamation and brackish water desalination. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biosorption of gold from computer microprocessor leachate solutions using chitin.

Science.gov (United States)

Côrtes, Letícia N; Tanabe, Eduardo H; Bertuol, Daniel A; Dotto, Guilherme L

2015-11-01

The biosorption of gold from discarded computer microprocessor (DCM) leachate solutions was studied using chitin as a biosorbent. The DCM components were leached with thiourea solutions, and two procedures were tested for recovery of gold from the leachates: (1) biosorption and (2) precipitation followed by biosorption. For each procedure, the biosorption was evaluated considering kinetic, equilibrium, and thermodynamic aspects. The general order model was able to represent the kinetic behavior, and the equilibrium was well represented by the BET model. The maximum biosorption capacities were around 35 mg g(-1) for both procedures. The biosorption of gold on chitin was a spontaneous, favorable, and exothermic process. It was found that precipitation followed by biosorption resulted in the best gold recovery, because other species were removed from the leachate solution in the precipitation step. This method enabled about 80% of the gold to be recovered, using 20 g L(-1) of chitin at 298 K for 4 h. Copyright © 2015 Elsevier Ltd. All rights reserved.

Determination of microamounts of uranium in waste solutions

International Nuclear Information System (INIS)

Birringer, K.J.; Netzer, S.; Kuhn, E.; Groll, P.

1975-07-01

A method for the determination of microamounts of uranium in presence of high amounts of fission and corrosion products is described. Uranium is separated by reversed-phase chromatography on a small column, packed with Voltalef micro and impregnated with TOPO. For the direct photometric determination uranium is eluted by TAM dissolved in ethanol/pyridine. The efficiency of the separation, using a suitable scrub-solution, was tested with solutions of simulated inactive fission and corrosion products. The reproducibility of the method, with 24 μg of uranium, is +- 2,5%. (orig.) [de

Traveling Wave Solutions of ZK-BBM Equation Sine-Cosine Method

Directory of Open Access Journals (Sweden)

Sadaf Bibi

2014-03-01

Full Text Available Travelling wave solutions are obtained by using a relatively new technique which is called sine-cosine method for ZK-BBM equations. Solution procedure and obtained results re-confirm the efficiency of the proposed scheme.

Shifts in climate suitability for wine production as a result of climate change in a temperate climate wine region of Romania

Science.gov (United States)

Irimia, Liviu Mihai; Patriche, Cristian Valeriu; Quenol, Hervé; Sfîcă, Lucian; Foss, Chris

2018-02-01

Climate change is causing important shifts in the suitability of regions for wine production. Fine scale mapping of these shifts helps us to understand the evolution of vineyard climates, and to find solutions through viticultural adaptation. The aim of this study is to identify and map the structural and spatial shifts that occurred in the climatic suitability for wine production of the Cotnari wine growing region (Romania) between 1961 and 2013. Discontinuities in trends of temperature were identified, and the averages and trends of 13 climatic parameters for the 1961 to 1980 and 1981 to 2013 time periods were analysed. Using the averages of these climatic parameters, climate suitability for wine production was calculated at a resolution of 30 m and mapped for each time period, and the changes analysed. The results indicate shifts in the area's historic climatic profile, due to an increase of heliothermal resources and precipitation constancy. The area's climate suitability for wine production was modified by the loss of climate suitability for white table wines, sparkling wines and wine for distillates; shifts in suitability to higher altitudes by about 67 m, and a 48.6% decrease in the area suitable for quality white wines; and the occurrence of suitable climates for red wines at lower altitudes. The study showed that climate suitability for wine production has a multi-level spatial structure, with classes requiring a cooler climate being located at a higher altitude than those requiring a warmer climate. Climate change has therefore resulted in the shift of climate suitability classes for wine production to higher altitudes.

A new procedure for implementing a geological disposal

International Nuclear Information System (INIS)

Anon.

2014-01-01

The British government has launched a new procedure for selecting and implementing a geological disposal. This procedure is based on long-term cooperation with municipalities that wish to home this facility. In a preliminary 2 year long step, a national geological survey will be performed in order to determine regions that are suitable to home a geological disposal. Then discussions between municipalities that are voluntary and the enterprise in charge of developing the project will begin. Municipalities will receive an investment up to 1 million pounds a year in the first years of the selecting procedure and then 2.5 million pounds a year when discussions become more formal. British authorities consider that the procedure for selecting a site may last up to 20 years. A previous attempt to find a site failed in 2013 when 2 regions that had been interested in the project since 2008, were finally rebuffed by the regional council that opposed the project. Scotland and Wales have their own strategy for the management of radioactive waste. (A.C.)

PROCESS OF ELIMINATING HYDROGEN PEROXIDE IN SOLUTIONS CONTAINING PLUTONIUM VALUES

Science.gov (United States)

Barrick, J.G.; Fries, B.A.

1960-09-27

A procedure is given for peroxide precipitation processes for separating and recovering plutonium values contained in an aqueous solution. When plutonium peroxide is precipitated from an aqueous solution, the supernatant contains appreciable quantities of plutonium and peroxide. It is desirable to process this solution further to recover plutonium contained therein, but the presence of the peroxide introduces difficulties; residual hydrogen peroxide contained in the supernatant solution is eliminated by adding a nitrite or a sulfite to this solution.

Workshops for state review of site suitability criteria for high-level radioactive waste repositories: analysis and recommendations

International Nuclear Information System (INIS)

1978-02-01

The purpose of this report is to present the views and recommendations of invited State officials and legislators participating in a workshop concerned with preliminary site suitability criteria for high level radioactive waste repositories. The workshops were open to the public and were conducted by the U. S. Nuclear Regulatory Commission (NRC) during September 1977 in three regional locations across the United States. This contractor report is the second of two reports and consolidates the discussion by State officials on the role of a State in siting a repository, NRC's waste management program, the transportation of high level wastes, the number and location of repositories and concerns with the socio-economic impacts of siting a repository in a community. The recommendations to the NRC can be categorized into four areas. These were: (1) general recommendations, (2) procedural recommendations, (3) recommendations for improving communications, and (4) specific recommendations on the preliminary siting criteria. The recommendations emphasized the need for early State involvement in the siting process, the need for an impacted State to assess repository operations, the need for early solution of waste transportation concerns, and the requirement that any repository developed insure the protection of the public health and safety as its most important characteristic. Other participant recommendations are included in the body of the report

Capability Database of Injection Molding Process— Requirements Study for Wider Suitability and Higher Accuracy

DEFF Research Database (Denmark)

Boorla, Srinivasa Murthy; Eifler, Tobias; Jepsen, Jens Dines O.

2017-01-01

for an improved applicability of corresponding database solutions in an industrial context. A survey of database users at all phases of product value chain in the plastic industry revealed that 59% of the participating companies use their own, internally created databases, although reported to be not fully...... adequate in most cases. Essential influences are the suitability of the provided data, defined by the content such as material, tolerance types, etc. covered, as well as its accuracy, largely influenced by the updating frequency. Forming a consortium with stakeholders, linking database update to technology...

Evaluation of didactic suitability indicators from curricular orientations

Directory of Open Access Journals (Sweden)

Pedro Arteaga

2012-12-01

Full Text Available Assessment of didactic suitability of mathematics teaching and learning processes requires suitable instruments to guide and support it. This paper presents a methodology for progressive improvement of such instruments to evaluate the suitability of mathematical instruction processes based on the analysis of curricular orientations. Analysis units are classifi ed according to the facets and components proposed by the Didactic Suitability Theory to identify norms and suitability indicators,which are compared with the system proposed by this theory, in order to point out agreements and complementarities. This methodology is exemplified through its application to the principles and standards of the National Council of Teachers of Mathematics (NCTM in the statistics content area at the level K-8.

Solution weighting for the SAND-II Monte Carlo code

International Nuclear Information System (INIS)

Oster, C.A.; McElroy, W.N.; Simons, R.L.; Lippincott, E.P.; Odette, G.R.

1976-01-01

Modifications to the SAND-II Error Analysis Monte Carlo code to include solution weighting based on input data uncertainties have been made and are discussed together with background information on the SAND-II algorithm. The new procedure permits input data having smaller uncertainties to have a greater influence on the solution spectrum than do the data having larger uncertainties. The results of an indepth study to find a practical procedure and the first results of its application to three important Interlaboratory LMFBR Reaction Rate (ILRR) program benchmark spectra (CFRMF, ΣΣ, and 235 U fission) are discussed

Regulation of Renewable Energy Sources to Optimal Power Flow Solutions Using ADMM: Preprint

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yijian; Hong, Mingyi; Dall' Anese, Emiliano; Dhople, Sairaj; Xu, Zi

2017-03-03

This paper considers power distribution systems featuring renewable energy sources (RESs), and develops a distributed optimization method to steer the RES output powers to solutions of AC optimal power flow (OPF) problems. The design of the proposed method leverages suitable linear approximations of the AC-power flow equations, and is based on the Alternating Direction Method of Multipliers (ADMM). Convergence of the RES-inverter output powers to solutions of the OPF problem is established under suitable conditions on the stepsize as well as mismatches between the commanded setpoints and actual RES output powers. In a broad sense, the methods and results proposed here are also applicable to other distributed optimization problem setups with ADMM and inexact dual updates.

Determination of free acid in plutonium (IV) solutions - thermometrically, potentiometrically

International Nuclear Information System (INIS)

Williams, T.L.; Tucker, G.M.; Huff, G.A.; Jordan, L.G.

1981-09-01

The thermometric titration technique was found to offer certain advantages over potentiometry in the determination of free acid in Pu(IV) solutions. The thermometric technique was applied to the determination of free acid in plutonium nitrate solutions using potassium fluoride to suppress the hydrolytic interference of plutonium(IV). The results indicate that 0.2 to 2.0 milliequivalents of free acid can be determined with acceptable bias and precision in solutions containing up to 30 milligrams of plutonium. In contrast, neither the thermometric nor the potentiometric technique was suitable for samples containing more than eight milligrams of plutonium complexed with potassium oxalate

Remarks about singular solutions to the Dirac equation

International Nuclear Information System (INIS)

Uhlir, M.

1975-01-01

In the paper singular solutions of the Dirac equation are investigated. They are derived in the Lorentz-covariant way of functions proportional to static multipole fields of scalar and (or) electromagnetic fields and of regular solutions of the Dirac equations. The regularization procedure excluding divergences of total energy, momentum and angular momentum of the spinor field considered is proposed

Determination of chemical solute transport parameters effecting radiostrontium interbed sediments

International Nuclear Information System (INIS)

Hemming, C.; Bunde, R.L.; Rosentreter, J.J.

1993-01-01

The extent to which radionuclides migrate in an aquifer system is a function of various physical, chemical, and biological processes. A measure of this migration rate is of primary concern when locating suitable storage sites for such species. Parameters including water-rock interactions, infiltration rates, chemical phase modification, and biochemical reactions all affect solute transport. While these different types of chemical reactions can influence solute transport in subsurface waters, distribution coefficients (Kd) can be send to effectively summarize the net chemical factors which dictate transport efficiency. This coefficient describes the partitioning of the solute between the solution and solid phase. Methodology used in determining and interpreting the distribution coefficient for radiostrontium in well characterized sediments will be presented

Baryon string model. II. Special solutions of classical three-string equations of motion

International Nuclear Information System (INIS)

Klimenko, S.V.; Kochin, V.N.; Plyushchai, M.S.; Pron'ko, G.P.

1986-01-01

The authors consider special solutions of the classical threestring equations of motion. The basic results needed for construction and analysis of the special solutions are examined. The authors consider very simple solutions in which the three-string node moves with the velocity of light. Singlemode solutions are studied. The graphical packet Atom is used to study and visualize the string dynamics. A new procedure was developed within the packet for graphical representation of many parameter functions. The distinctive feature of these procedures is the large class of functions (including explicit, implicit, and parametric functions) that can be represented by means of parametric, coordinate, and functional isolines

Growth of single crystals from solutions using semi-permeable membranes

Science.gov (United States)

Varkey, A. J.; Okeke, C. E.

1983-05-01

A technique suitable for growth of single crystals from solutions using semi-preamble membranes is described. Using this technique single crystals of copper sulphate, potassium bromide and ammonium dihydrogen phosphate have been successfully grown. Advantages of this technique over other methods are discussed.

45 CFR 12a.4 - Suitability determination.

Science.gov (United States)

2010-10-01

... underutilized will be reviewed for suitability no earlier than six months prior to the expected date when the... following: (1) The suitability determination for a particular piece of property, and the reasons for that...

Selecting suitable enclosures for digitally printed materials

International Nuclear Information System (INIS)

Burge, D; Rima, L

2010-01-01

It cannot be assumed that storage enclosures considered safe for traditionally printed images and documents are suitable for modern, digitally printed materials. In this project, a large variety of digital print types were tested using a modified version of the ISO 18916 Imaging materials-Processed imaging materials-Photographic activity test for enclosure materials standard to assess the risk to digital prints by paper enclosures known to be inert or reactive with traditional photographic prints. The types of enclosures tested included buffered and non-buffered cotton papers, and groundwood paper. In addition, qualitative filter paper that had been wetted and dried with either an acidic or basic solution was also tested to determine the effects of enclosure pH on digitally printed materials. It was determined that, in general, digital prints tended to be less reactive with various enclosure types than traditional prints. Digital prints were most sensitive to paper that contained groundwood. The enclosure reactivity test results were then integrated with previous published work on the tendencies of various enclosure types to abrade, ferrotype, or block to digital prints in order to create a comprehensive set of recommendations for digital print storage enclosures.

Smooth solutions for the dyadic model

International Nuclear Information System (INIS)

Barbato, David; Morandin, Francesco; Romito, Marco

2011-01-01

We consider the dyadic model, which is a toy model to test issues of well-posedness and blow-up for the Navier–Stokes and Euler equations. We prove well-posedness of positive solutions of the viscous problem in the relevant scaling range which corresponds to Navier–Stokes. Likewise we prove well-posedness for the inviscid problem (in a suitable regularity class) when the parameter corresponds to the strongest transport effect of the nonlinearity

Forward osmosis for oily wastewater reclamation: Multi-charged oxalic acid complexes as draw solutes

KAUST Repository

Ge, Qingchun

2017-06-11

Forward osmosis (FO) has demonstrated its merits in hybrid FO seawater desalination. However, FO may have a potential for other applications if suitable draw solutes are available. In this study, a series of novel draw solutes based on oxalic acid (OA)-transitional metal complexes are presented. Influential factors of FO performance have been systematically investigated by varying the transitional metals, cations of the complex draw solutes as well as the experimental conditions. Compared to NaCl and other recently synthesized draw solutes, the OA complexes show superior FO performance in terms of high water fluxes up to 27.5 and 89.1 LMH under the respective FO and PRO (pressure retarded osmosis) modes, both with negligible reverse solute fluxes. The features of octahedral geometry, abundant hydrophilic groups and ionic species are crucial for the OA complexes as appropriate draw solutes with satisfactory FO performance. Among the synthesized OA complexes, the ammonium salt of chromic complex (NH4-Cr-OA) outperforms others due to the presence of more ionic species in its complex system. NH4-Cr-OA also performs better than the typical NaCl draw solute in FO oily wastewater treatment with higher water recovery and negligible reverse fluxes. Dilute solutions of OA complexes have been reconcentrated through membrane distillation (MD) and reused to new round of FO processes. The OA complexes have demonstrated their suitability and superiority as a novel class of draw solutes for the FO process in this study.

Procedure for extraction of disparate data from maps into computerized data bases

Science.gov (United States)

Junkin, B. G.

1979-01-01

A procedure is presented for extracting disparate sources of data from geographic maps and for the conversion of these data into a suitable format for processing on a computer-oriented information system. Several graphic digitizing considerations are included and related to the NASA Earth Resources Laboratory's Digitizer System. Current operating procedures for the Digitizer System are given in a simplified and logical manner. The report serves as a guide to those organizations interested in converting map-based data by using a comparable map digitizing system.

Assessment of Climate Suitability of Maize in South Korea

Science.gov (United States)

Hyun, S.; Choi, D.; Seo, B.

2017-12-01

Assessing suitable areas for crops would be useful to design alternate cropping systems as an adaptation option to climate change adaptation. Although suitable areas could be identified by using a crop growth model, it would require a number of input parameters including cultivar and soil. Instead, a simple climate suitability model, e.g., EcoCrop model, could be used for an assessment of climate suitability for a major grain crop. The objective of this study was to assess of climate suitability for maize using the EcoCrop model under climate change conditions in Korea. A long term climate data from 2000 - 2100 were compiled from weather data source. The EcoCrop model implemented in R was used to determine climate suitability index at each grid cell. Overall, the EcoCrop model tended to identify suitable areas for maize production near the coastal areas whereas the actual major production areas located in inland areas. It is likely that the discrepancy between assessed and actual crop production areas would result from the socioeconomic aspects of maize production. Because the price of maize is considerably low, maize has been grown in an area where moisture and temperature conditions would be less than optimum. In part, a simple algorithm to predict climate suitability for maize would caused a relatively large error in climate suitability assessment under the present climate conditions. In 2050s, the climate suitability for maize increased in a large areas in southern and western part of Korea. In particular, the plain areas near the coastal region had considerably greater suitability index in the future compared with mountainous areas. The expansion of suitable areas for maize would help crop production policy making such as the allocation of rice production area for other crops due to considerably less demand for the rice in Korea.

A National Needs Assessment to Identify Technical Procedures in Vascular Surgery for Simulation Based Training

DEFF Research Database (Denmark)

Nayahangan, L J; Konge, L; Schroeder, T V

2017-01-01

to identify technical procedures that vascular surgeons should learn. Round 2 was a survey that used a needs assessment formula to explore the frequency of procedures, the number of surgeons performing each procedure, risk and/or discomfort, and feasibility for simulation based training. Round 3 involved...... eliminated, resulting in a final prioritised list of 19 technical procedures. Conclusion A national needs assessment using a standardised Delphi method identified a list of procedures that are highly suitable and may provide the basis for future simulation based training programs for vascular surgeons......Objectives and background Practical skills training in vascular surgery is facing challenges because of an increased number of endovascular procedures and fewer open procedures, as well as a move away from the traditional principle of “learning by doing.” This change has established simulation...

The isolation of lutetium from gadolinium contained in Purex process solutions

International Nuclear Information System (INIS)

Bostick, D.T.; Vick, D.O.; May, M.P.; Walker, R.L.

1992-09-01

A chemical separation procedure has been devised to isolate Lu from Purex dissolver solutions containing the neutron poison, Gd. The isolation procedure involves the removal of U and >Pu from a dissolver solution using tributylphosphate solvent extraction. If required, solvent extraction using di-(2-ethylhexyl) phosphoric acid can be employed to further purify the sample be removing alkali and alkali earth elements. Finally, Lu is chromatographically separated from Gd and rare earth fission products on a Dowex 50W-X8 resin column using an alpha-hydroxyisobutyrate eluant. The success of the chemical separation procedure has been demonstrated in the quantitative recovery of as little as 1.4 ng Lu from solutions containing a 5000-fold excess of Gd. Additionally, Lu has been isolated from synthetic dissolver samples containing U, Ba, Cs, and Gd. Thermal emission MS data indicated that the Lu fraction of the synthetic sample was free of Gd interference

Procedure for the obtainment of ammonium uranyl-tricarbonate suitable for the preparation of sinterable UO2

International Nuclear Information System (INIS)

Anasco, Roberto; Amendolara, M.M.; De La Fuente, M.; Gonzalez, A.G.; La Gamma de Batistoni, A.M.; Garcia, E.

1980-01-01

Experiments carried out to obtain Ammonium Uranyl-Tricarbonate (AUC) of nuclear purity and with the appropriate physical characteristics to serve as an intermediate stage for the obtainment of sinterable Uranium Dioxide are described. AUC was obtained by precipitation with gaseous ammonium and carbon dioxide from aqueous solutions re-circulation, controlling, in both cases, the flow of the reactive gases, the pH and the temperature. The analyzed working conditions are described, giving also the results from the distribution of the particle size and morphology of the crystals. (M.E.L.) [es

CFD code verification and the method of manufactured solutions

International Nuclear Information System (INIS)

Pelletier, D.; Roache, P.J.

2002-01-01

This paper presents the Method of Manufactured Solutions (MMS) for CFD code verification. The MMS provides benchmark solutions for direct evaluation of the solution error. The best benchmarks are exact analytical solutions with sufficiently complex solution structure to ensure that all terms of the differential equations are exercised in the simulation. The MMS provides a straight forward and general procedure for generating such solutions. When used with systematic grid refinement studies, which are remarkably sensitive, the MMS provides strong code verification with a theorem-like quality. The MMS is first presented on simple 1-D examples. Manufactured solutions for more complex problems are then presented with sample results from grid convergence studies. (author)

Preparing a suitable solid target for generating copper-64 using a biomedical cyclotron

International Nuclear Information System (INIS)

Jeffery, Charmaine; Cryer, David; Chan, Sun; Asad, Ali; Fleming, Adam; Hubble, Lee

2009-01-01

Full text: Radiopharmaceutical research at SCGH has been advancing in the production of copper-64, a promising radionuclide for PET. Production has commenced using a self-manufactured solid target with alBA 18/9 cyclotron, via the 6 4 N i(p,n) 6 4 C u reaction pathway. One aspect of the project has been the preparation of a suitable solid target for irradiation. The chosen production method involves electrolysis of a solution of nickel ammonium sulphate in a self-manufactured electroplating cell, using a gold disk as the cathode for deposition of nickel metal. Various defects in the nickel surface were observed ∼ including cracks, formation of pits and inclusions, loose powder-like plating, lack of metallic lustre and lifting of the plated nickel. Several variables were investigated - including adjustment of the anode-cathode distance, anode composition, solution composition, and voltage/current settings. A suitable method that produced acceptable plating was achieved - the surface was then analysed to ensure there were no underlying defects. Three analytical techniques were used - AFM, SEM and optical profilometry. Two disks were ana lysed (approx. 3 0 m g of natNi plated). The depth of plating, evenness of plating and surface uniformity were of particular interest. Conclusions: Analysis revealed that the surface was not completely uniform (thinner at edges, 'well' in centre, with inclusions on the surface more prevalent than pitting), and required more nickel to be plated to reach optimum thickness. Final target specifications are still being optimised, however test irradiation of a solid target ( 3 1 n ickel, I l0 m g) proved that a sound solid target can be reliably produced and irradiated.

Process for the removal of radium from acidic solutions containing same

International Nuclear Information System (INIS)

Scheitlin, F.M.

1984-01-01

Radium is removed from an inorganic-acid solution contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities. The invention is applicable, for example, to the recovery of 226 Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings, and thus contain thorium and uranium. The contaminated fly ash may be incorporated in a suitable matrix and stored, and the residual solutions processed to separate uranium and thorium. (author)

A Neural Networks Based Operation Guidance System for Procedure Presentation and Validation

International Nuclear Information System (INIS)

Seung, Kun Mo; Lee, Seung Jun; Seong, Poong Hyun

2006-01-01

In this paper, a neural network based operator support system is proposed to reduce operator's errors in abnormal situations in nuclear power plants (NPPs). There are many complicated situations, in which regular and suitable operations should be done by operators accordingly. In order to regulate and validate operators' operations, it is necessary to develop an operator support system which includes computer based procedures with the functions for operation validation. Many computerized procedures systems (CPS) have been recently developed. Focusing on the human machine interface (HMI) design and procedures' computerization, most of CPSs used various methodologies to enhance system's convenience, reliability and accessibility. Other than only showing procedures, the proposed system integrates a simple CPS and an operation validation system (OVS) by using artificial neural network (ANN) for operational permission and quantitative evaluation

Human Factors Evaluation of Procedures for Periodic Safety Review of Yonggwang Unit no. 1, 2

Energy Technology Data Exchange (ETDEWEB)

Lee, Yong Hee; Lee, Jung Woon; Park, Jae Chang (and others)

2006-01-15

This report describes the results of human factors assessment on the plant operating procedures as part of Periodic Safety Review(PSR) of Yonggwang Nuclear Power Plant Unit no. 1, 2. The suitability of item and appropriateness of format and structure in the key operating procedures of nuclear power plants were investigated by the review of plant operating experiences and procedure documents, field survey, and experimental assessment on some part of procedures. A checklist was used to perform this assessment and record the review results. The reviewed procedures include EOP(Emergency Operating Procedures), GOP(General Operating Procedures), AOP(Abnormal Operating Procedures), and management procedures of some technical departments. As results of the assessments, any significant problem challenging the safety was not found on the human factors in the operating procedures. However, several small items to be changed and improved were discovered. An action plan is recommended to accommodate the suggestions and review comments. It will enhance the plant safety on the operating procedure.

Modified micro-diffusion method for 15N-enriched soil solutions

International Nuclear Information System (INIS)

Aigner, M.

2000-01-01

The preparation of solutions for determination of 15 N/ 14 N isotope ratios is described, with special reference to dilute samples. A micro-diffusion method has been simplified to be more suitable for rapid isotope-ratio determination in soil solutions collected in tensionics. Ammonia expelled during micro-diffusion is captured on acidified filter discs fixed to the caps of gas-tight vials. The discs are transferred to tin capsules for shipment to the Soil Science Unit for 15 N-enrichment determination. (author)

Simultaneous contrast: evidence from licking microstructure and cross-solution comparisons.

Science.gov (United States)

Dwyer, Dominic M; Lydall, Emma S; Hayward, Andrew J

2011-04-01

The microstructure of rats' licking responses was analyzed to investigate both "classic" simultaneous contrast (e.g., Flaherty & Largen, 1975) and a novel discrete-trial contrast procedure where access to an 8% test solution of sucrose was preceded by a sample of either 2%, 8%, or 32% sucrose (Experiments 1 and 2, respectively). Consumption of a given concentration of sucrose was higher when consumed alongside a low rather than high concentration comparison solution (positive contrast) and consumption of a given concentration of sucrose was lower when consumed alongside a high rather than a low concentration comparison solution (negative contrast). Furthermore, positive contrast increased the size of lick clusters while negative contrast decreased the size of lick clusters. Lick cluster size has a positive monotonic relationship with the concentration of palatable solutions and so positive and negative contrasts produced changes in lick cluster size that were analogous to raising or lowering the concentration of the test solution respectively. Experiment 3 utilized the discrete-trial procedure and compared contrast between two solutions of the same type (sucrose-sucrose or maltodextrin-maltodextrin) or contrast across solutions (sucrose-maltodextrin or maltodextrin-sucrose). Contrast effects on consumption were present, but reduced in size, in the cross-solution conditions. Moreover, lick cluster sizes were not affected at all by cross-solution contrasts as they were by same-solution contrasts. These results are consistent with the idea that simultaneous contrast effects depend, at least partially, on sensory mechanisms.

Selection strategy for the most Suitable CEC method for clay barrier characterisation

International Nuclear Information System (INIS)

Dohrmann, R.; Kaufhold, S.

2010-01-01

competition to barium ions in smectite interlayers. The present study aims at proposing a selection strategy for CEC methods including exchangeable cation determination of different clay materials typically used in radioactive waste disposal studies. 1) If the clay/bentonite contains calcium carbonates but no gypsum several methods are available, all of them are based on a saturation of the exchange solution with calcite before the exchange experiment starts: AgTU-calcite, CoHex-calcite, and Cu-trien5xcalcite. If dolomite is present the initial calcite saturation minimizes dolomite dissolution as well (proved for AgTU-calcite). 2) If a bentonite contains carbonates and gypsum the only known successful method for determination of all exchangeable cations (including calcium) and the CEC is a combination of two separate results: i) calcite saturation of exchange solution (e.g. Cu-trien5xcalcite) and ii) quantification of gypsum with suitable mineralogical methods. Result i) is free of error caused by calcite dissolution; however it is still wrong because it contains significant amounts of Ca 2+ from gypsum dissolution. After proving that gypsum was completely dissolved during the exchange experiment result ii) was used to subtract the theoretical Ca 2+ portion of gypsum from result i). Gypsum saturation of exchange solutions was tested as not suitable owing to the high solubility of gypsum which results in high initial Ca 2+ concentrations. 3) If no such soluble minerals are present and if the pore water contains no excess electrolyte then usually any accepted CEC method can be used, however, the results should always be checked for plausibility (e.g. using mineralogical composition of the sample). Any accepted method means that methods with known systematic errors (hydrophobic interaction, dependency on layer charge density) are excluded. (authors)

A new solution method for wheel/rail rolling contact.

Science.gov (United States)

Yang, Jian; Song, Hua; Fu, Lihua; Wang, Meng; Li, Wei

2016-01-01

To solve the problem of wheel/rail rolling contact of nonlinear steady-state curving, a three-dimensional transient finite element (FE) model is developed by the explicit software ANSYS/LS-DYNA. To improve the solving speed and efficiency, an explicit-explicit order solution method is put forward based on analysis of the features of implicit and explicit algorithm. The solution method was first applied to calculate the pre-loading of wheel/rail rolling contact with explicit algorithm, and then the results became the initial conditions in solving the dynamic process of wheel/rail rolling contact with explicit algorithm as well. Simultaneously, the common implicit-explicit order solution method is used to solve the FE model. Results show that the explicit-explicit order solution method has faster operation speed and higher efficiency than the implicit-explicit order solution method while the solution accuracy is almost the same. Hence, the explicit-explicit order solution method is more suitable for the wheel/rail rolling contact model with large scale and high nonlinearity.

A Procedure for Modeling Photovoltaic Arrays under Any Configuration and Shading Conditions

Directory of Open Access Journals (Sweden)

Daniel Gonzalez Montoya

2018-03-01

Full Text Available Photovoltaic (PV arrays can be connected following regular or irregular connection patterns to form regular configurations (e.g., series-parallel, total cross-tied, bridge-linked, etc. or irregular configurations, respectively. Several reported works propose models for a single configuration; hence, making the evaluation of arrays with different configuration is a considerable time-consuming task. Moreover, if the PV array adopts an irregular configuration, the classical models cannot be used for its analysis. This paper proposes a modeling procedure for PV arrays connected in any configuration and operating under uniform or partial shading conditions. The procedure divides the array into smaller arrays, named sub-arrays, which can be independently solved. The modeling procedure selects the mesh current solution or the node voltage solution depending on the topology of each sub-array. Therefore, the proposed approach analyzes the PV array using the least number of nonlinear equations. The proposed solution is validated through simulation and experimental results, which demonstrate the proposed model capacity to reproduce the electrical behavior of PV arrays connected in any configuration.

Comparison of the salt domes Asse and Gorleben with regard to their suitability for the final storage of radoactive wastes

International Nuclear Information System (INIS)

Deisenroth, Norbert; Kokorsch, Rudolf

2012-01-01

In Germany, the search for a proper solution to the issue of final disposal of radioactive wastes is complicated by political leaders. The Gorleben moratorium from October 2000 delayed the proper solution unnecessary to ten years. Asse proves that salt domes such as Gorleben do not offer a permanent partitioning of the waste over the biosphere. With this in mind, the authors of the contribution under consideration compare the two salt domes Gorleben and Asse from a mining and geological point of view based on publicly available data with regard to their suitability for the disposal of radioactive waste.

Buffered lidocaine and bupivacaine mixture - the ideal local anesthetic solution?

Science.gov (United States)

Best, Corliss A; Best, Alyssa A; Best, Timothy J; Hamilton, Danielle A

2015-01-01

The use of injectable local anesthetic solutions to facilitate pain-free surgery is an integral component of many procedures performed by the plastic surgeon. In many instances, a solution that has both rapid onset and prolonged duration of analgesia is optimal. A combination of lidocaine and bupivacaine, plain or with epinephrine, is readily available in most Canadian health care settings where such procedures are performed, and fulfills these criteria. However, commercially available solutions of both medications are acidic and cause a burning sensation on injection. Buffering to neutral pH with sodium bicarbonate is a practical method to mitigate the burning sensation, and has the added benefit of increasing the fraction of nonionized lipid soluble drug available. The authors report on the proportions of the three drugs to yield a neutral pH, and the results of an initial survey regarding the use of the combined solution with epinephrine in hand surgery.

New LASER fluorometric HPLC detection for ortho-tyrosine in gamma-irradiated phenylalanine solution and pork

International Nuclear Information System (INIS)

Miyahara, Makoto; Toyoda, Masatake; Saito, Yukio; Nagasawa, Taeko; Izumi, Keiko; Kitamura, Mayumi

1999-01-01

New analytical procedure for o-tyrosine was studied to investigate effects of gamma irradiation on aqueous phenylalanine solution and pork. The process includes extraction and hydrolysis of protein, derivatization of the free amino acid by fluororeagent, and finally separation and detection by LASER fluorometric HPLC. The detection limit was 25ng. To study how the procedure works, irradiated phenylalanine solution and pork were analyzed. The samples were irradiated at doses up to 10 kGy at room temperature. Three tyrosine isomers were detected in phenylalanine solution, and 2 isomers (o-and p-tyrosine) were found in pork. Dose response was found in the formation of the isomers both in phenylalanine solution and in pork. O-tyrosine peak obtained from irradiated pork was separated from interference successfully. Those findings illustrate the procedure may be applicable to detection of irradiated food. (author)

Development of a freeze-drying process of waste-solution, 2

International Nuclear Information System (INIS)

Kondo, Isao; Kawasaki, Takeshi

1988-01-01

The waste solution treatment process in Plutonium Conversion Development Facility (PCDF) consists of Evaporation-Condensation and Neutrazation-Agglometation-Precipitation process, which produces the distillate as recovered acid at first step and separates Pu-U element from condenced solution at second step. This process needs many stages to get high decontamination efficiency and then the Evaporator is in very corrosive state because the nitric acid solution is heated over 100 degrees C to be evaporated. So, in PCDF, it was started the development of Freeze-Drying process to waste solution treatment. This process is suitable for a little quantity of the solution including nitric acid as produced in the Microwave Heating method. Moreover the process has high decontamination efficiency and has good performance of equipment. The result of the cold test of Freeze-Drying process with nitric acid is discribed in this paper. (author)

An accurate approximate solution of optimal sequential age replacement policy for a finite-time horizon

International Nuclear Information System (INIS)

Jiang, R.

2009-01-01

It is difficult to find the optimal solution of the sequential age replacement policy for a finite-time horizon. This paper presents an accurate approximation to find an approximate optimal solution of the sequential replacement policy. The proposed approximation is computationally simple and suitable for any failure distribution. Their accuracy is illustrated by two examples. Based on the approximate solution, an approximate estimate for the total cost is derived.

How does the workload and work activities of procedural GPs compare to non-procedural GPs?

Science.gov (United States)

Russell, Deborah J; McGrail, Matthew R

2017-08-01

To investigate patterns of Australian GP procedural activity and associations with: geographical remoteness and population size hours worked in hospitals and in total; and availability for on-call DESIGN AND PARTICIPANTS: National annual panel survey (Medicine in Australia: Balancing Employment and Life) of Australian GPs, 2011-2013. Self-reported geographical work location, hours worked in different settings, and on-call availability per usual week, were analysed against GP procedural activity in anaesthetics, obstetrics, surgery or emergency medicine. Analysis of 9301 survey responses from 4638 individual GPs revealed significantly increased odds of GP procedural activity in anaesthetics, obstetrics or emergency medicine as geographical remoteness increased and community population size decreased, albeit with plateauing of the effect-size from medium-sized (population 5000-15 000) rural communities. After adjusting for confounders, procedural GPs work more hospital and more total hours each week than non-procedural GPs. In 2011 this equated to GPs practising anaesthetics, obstetrics, surgery, and emergency medicine providing 8% (95%CI 0, 16), 13% (95%CI 8, 19), 8% (95%CI 2, 15) and 18% (95%CI 13, 23) more total hours each week, respectively. The extra hours are attributable to longer hours worked in hospital settings, with no reduction in private consultation hours. Procedural GPs also carry a significantly higher burden of on-call. The longer working hours and higher on-call demands experienced by rural and remote procedural GPs demand improved solutions, such as changes to service delivery models, so that long-term procedural GP careers are increasingly attractive to current and aspiring rural GPs. © 2016 National Rural Health Alliance Inc.

Cation exchange process for recovery of plutonium from laboratory solutions containing chloride

International Nuclear Information System (INIS)

Gray, L.W.

1978-10-01

A cation exchange technique was developed for the separation of plutonium from laboratory solutions containing either Pu(III) or Pu(III)--Pu(IV) mixtures in acidic solutions containing chloride ions. The procedure consists of adjusting the acid concentration to less than one molar and adjusting the valence of the plutonium ion to the (III) state, if necessary. The adjusted solution is fed to a cation exchange column and washed with distilled water to remove residual chlorides from the column. Plutonium is then eluted from the column with 5M nitric acid containing 0.34M sulfamic acid. This procedure was used to separate plutonium from 1.2M chloride solution on a production-scale column. Typical plutonium recovery was 99.97%, while greater than 96% of the original chloride was rejected

Optimization of simulated moving bed (SMB) chromatography: a multi-level optimization procedure

DEFF Research Database (Denmark)

Jørgensen, Sten Bay; Lim, Young-il

2004-01-01

objective functions (productivity and desorbent consumption), employing the standing wave analysis, the true moving bed (TMB) model and the simulated moving bed (SMB) model. The procedure is constructed on a non-worse solution property advancing level by level and its solution does not mean a global optimum...

Recursive solution for dynamic response of one-dimensional structures with time-dependent boundary conditions

Energy Technology Data Exchange (ETDEWEB)

Abadi, Mohammad Tahaye [Aerospace Research Institute, Tehran (Iran, Islamic Republic of)

2015-10-15

A recursive solution method is derived for the transient response of one-dimensional structures subjected to the general form of time dependent boundary conditions. Unlike previous solution methods that assumed the separation of variables, the present method involves formulating and solving the dynamic problems using the summation of two single-argument functions satisfying the motion equation. Based on boundary and initial conditions, a recursive procedure is derived to determine the single-argument functions. Such a procedure is applied to the general form of boundary conditions, and an analytical solution is derived by solving the recursive equation. The present solution method is implemented for base excitation problems, and the results are compared with those of the previous analytical solution and the Finite element (FE) analysis. The FE results converge to the present analytical solution, although considerable error is found in predicting a solution method on the basis of the separation of variables. The present analytical solution predicts the transient response for wave propagation problems in broadband excitation frequencies.

Recursive solution for dynamic response of one-dimensional structures with time-dependent boundary conditions

International Nuclear Information System (INIS)

Abadi, Mohammad Tahaye

2015-01-01

A recursive solution method is derived for the transient response of one-dimensional structures subjected to the general form of time dependent boundary conditions. Unlike previous solution methods that assumed the separation of variables, the present method involves formulating and solving the dynamic problems using the summation of two single-argument functions satisfying the motion equation. Based on boundary and initial conditions, a recursive procedure is derived to determine the single-argument functions. Such a procedure is applied to the general form of boundary conditions, and an analytical solution is derived by solving the recursive equation. The present solution method is implemented for base excitation problems, and the results are compared with those of the previous analytical solution and the Finite element (FE) analysis. The FE results converge to the present analytical solution, although considerable error is found in predicting a solution method on the basis of the separation of variables. The present analytical solution predicts the transient response for wave propagation problems in broadband excitation frequencies.

New solutions of the confluent Heun equation

Directory of Open Access Journals (Sweden)

Harold Exton

1998-05-01

Full Text Available New compact triple series solutions of the confluent Heun equation (CHE are obtained by the appropriate applications of the Laplace transform and its inverse to a suitably constructed system of soluble differential equations. The computer-algebra package MAPLE V is used to tackle an auxiliary system of non-linear algebraic equations. This study is partly motivated by the relationship between the CHE and certain Schrödininger equations.

A Survey of Procedural Methods for Terrain Modelling

NARCIS (Netherlands)

Smelik, R.M.; Kraker, J.K. de; Groenewegen, S.A.; Tutenel, T.; Bidarra, R.

2009-01-01

Procedural methods are a promising but underused alternative to manual content creation. Commonly heard drawbacks are the randomness of and the lack of control over the output and the absence of integrated solutions, although more recent publications increasingly address these issues. This paper

Existence and Stability of Solutions for Implicit Multivalued Vector Equilibrium Problems

Directory of Open Access Journals (Sweden)

Li Qiuying

2011-01-01

Full Text Available A class of implicit multivalued vector equilibrium problems is studied. By using the generalized Fan-Browder fixed point theorem, some existence results of solutions for the implicit multivalued vector equilibrium problems are obtained under some suitable assumptions. Moreover, a stability result of solutions for the implicit multivalued vector equilibrium problems is derived. These results extend and unify some recent results for implicit vector equilibrium problems, multivalued vector variational inequality problems, and vector variational inequality problems.

Operator approach to solutions of the constrained BKP hierarchy

International Nuclear Information System (INIS)

Shen, Hsin-Fu; Lee, Niann-Chern; Tu, Ming-Hsien

2011-01-01

The operator formalism to the vector k-constrained BKP hierarchy is presented. We solve the Hirota bilinear equations of the vector k-constrained BKP hierarchy via the method of neutral free fermion. In particular, by choosing suitable group element of O(∞), we construct rational and soliton solutions of the vector k-constrained BKP hierarchy.

Design and optimisation of purification procedure for biodiesel washing

Directory of Open Access Journals (Sweden)

S.B. Glišić

2009-09-01

Full Text Available Almost complete methanolysis of triglycerides is usually not enough to fulfil the strict standards of biodiesel quality. A key step in this process is neutralization of alkali (catalyst followed by the washing procedure necessary for removing different impurities such as traces of catalyst and methanol and removal of soaps and glycerol from esters phase. The washing with hot water is still widely used in many industrial units for the biodiesel production. In this study, different procedures of biodiesel washing using hot water were investigated. The orto-phosphoric acid was suggested as the best compound for alkali catalyst (sodium hydroxide neutralization. The main goal of the performed analysis was to minimize the water usage in the washing-neutralization step during the biodiesel production. Such solution would make the process of biodiesel synthesis more economical taking into account the decrease of energy consumed for evaporation of water during the final product purification, as well as more acceptable procedure related to the impact on environment (minimal waste water release. Results of the performed simulation of the washing process supported by original experimental data suggested that neutralization after the optimized washing process of the methyl ester layer could be the best solution. The proposed washing procedure significantly decreases the amount of waste water giving at the same time the desired purity of final products (biodiesel and glycerol. The simulation of the process was performed using ASPEN plus software supported by ELCANTREL and UNIQUAC procedure of required properties calculation

Procedure for coating articles with pyrolytic carbon

International Nuclear Information System (INIS)

Adams, C.C.; Allen, C.L.; Besenbruch, G.E.A.

1976-01-01

A method to coat articles with pyrolytic carbon is described which is particularly suitable for small nuclear fuel particles as one obtains a very homogeneous layer. The pyrolytic carbon is produced according to the invention by decomposing a hydrocarbon gas mixture composed of an inert gas share (20-65 Vol%) and a mixture of acetylene and propylene. It is favourable to have the hydrocarbon mixture contain between 50 and 55 Vol% acetylene. Variations on the known procedure are given. The coating of spherical thorium dioxide particles is mentioned as an example. (UWI) [de

Forward osmosis for oily wastewater reclamation: Multi-charged oxalic acid complexes as draw solutes.

Science.gov (United States)

Ge, Qingchun; Amy, Gary Lee; Chung, Tai-Shung

2017-10-01

Forward osmosis (FO) has demonstrated its merits in hybrid FO seawater desalination. However, FO may have a potential for other applications if suitable draw solutes are available. In this study, a series of novel draw solutes based on oxalic acid (OA)-transitional metal complexes are presented. Influential factors of FO performance have been systematically investigated by varying the transitional metals, cations of the complex draw solutes as well as the experimental conditions. Compared to NaCl and other recently synthesized draw solutes, the OA complexes show superior FO performance in terms of high water fluxes up to 27.5 and 89.1 LMH under the respective FO and PRO (pressure retarded osmosis) modes, both with negligible reverse solute fluxes. The features of octahedral geometry, abundant hydrophilic groups and ionic species are crucial for the OA complexes as appropriate draw solutes with satisfactory FO performance. Among the synthesized OA complexes, the ammonium salt of chromic complex (NH 4 -Cr-OA) outperforms others due to the presence of more ionic species in its complex system. NH 4 -Cr-OA also performs better than the typical NaCl draw solute in FO oily wastewater treatment with higher water recovery and negligible reverse fluxes. Dilute solutions of OA complexes have been reconcentrated through membrane distillation (MD) and reused to new round of FO processes. The OA complexes have demonstrated their suitability and superiority as a novel class of draw solutes for the FO process in this study. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Ecology suitability study of Ephedra intermedia].

Science.gov (United States)

Ma, Xiao-Hui; Lu, You-Yuan; Huang, De-Dong; Zhu, Tian-Tian; Lv, Pei-Lin; Jin, Ling

2017-06-01

The study aims at predicting ecological suitability of Ephedra intermedia in China by using maximum entropy Maxent model combined with GIS, and finding the main ecological factors affecting the distribution of E. intermedia suitability in appropriate growth area. Thirty-eight collected samples of E. intermedia and E. intermedia and 116 distribution information from CVH information using ArcGIS technology were analyzed. MaxEnt model was applied to forecast the E. intermedia in our country's ecology. E. intermedia MaxEnt ROC curve model training data and testing data sets the AUC value was 0.986 and 0.958, respectively, which were greater than 0.9, tending to be 1.The calculated E. intermedia habitat suitability by the model showed a high accuracy and credibility, which indicated that MaxEnt model could well predict the potential distribution area of E. intermedia in China. Copyright© by the Chinese Pharmaceutical Association.

A coupled Eulerian/Lagrangian method for the solution of three-dimensional vortical flows

Science.gov (United States)

Felici, Helene Marie

1992-01-01

A coupled Eulerian/Lagrangian method is presented for the reduction of numerical diffusion observed in solutions of three-dimensional rotational flows using standard Eulerian finite-volume time-marching procedures. A Lagrangian particle tracking method using particle markers is added to the Eulerian time-marching procedure and provides a correction of the Eulerian solution. In turn, the Eulerian solutions is used to integrate the Lagrangian state-vector along the particles trajectories. The Lagrangian correction technique does not require any a-priori information on the structure or position of the vortical regions. While the Eulerian solution ensures the conservation of mass and sets the pressure field, the particle markers, used as 'accuracy boosters,' take advantage of the accurate convection description of the Lagrangian solution and enhance the vorticity and entropy capturing capabilities of standard Eulerian finite-volume methods. The combined solution procedures is tested in several applications. The convection of a Lamb vortex in a straight channel is used as an unsteady compressible flow preservation test case. The other test cases concern steady incompressible flow calculations and include the preservation of turbulent inlet velocity profile, the swirling flow in a pipe, and the constant stagnation pressure flow and secondary flow calculations in bends. The last application deals with the external flow past a wing with emphasis on the trailing vortex solution. The improvement due to the addition of the Lagrangian correction technique is measured by comparison with analytical solutions when available or with Eulerian solutions on finer grids. The use of the combined Eulerian/Lagrangian scheme results in substantially lower grid resolution requirements than the standard Eulerian scheme for a given solution accuracy.

Exact self-similar solutions for the magnetized Noh Z pinch problem

International Nuclear Information System (INIS)

Velikovich, A. L.; Giuliani, J. L.; Thornhill, J. W.; Zalesak, S. T.; Gardiner, T. A.

2012-01-01

A self-similar solution is derived for a radially imploding cylindrical plasma with an embedded, azimuthal magnetic field. The plasma stagnates through a strong, outward propagating shock wave of constant velocity. This analysis is an extension of the classic Noh gasdynamics problem to its ideal magnetohydrodynamics (MHD) counterpart. The present exact solution is especially suitable as a test for MHD codes designed to simulate linear Z pinches. To demonstrate the application of the new solution to code verification, simulation results from the cylindrical R-Z version of Mach2 and the 3D Cartesian code Athena are compared against the analytic solution. Alternative routines from the default ones in Athena lead to significant improvement of the results, thereby demonstrating the utility of the self-similar solution for verification.

Suitability of an MRMCE (multi-resolution minimum cross entropy) algorithm for online monitoring of a two-phase flow

International Nuclear Information System (INIS)

Wang, Qi; Wang, Huaxiang; Xin, Shan

2011-01-01

The flow regimes are important characteristics to describe two-phase flows, and measurement of two-phase flow parameters is becoming increasingly important in many industrial processes. Computerized tomography (CT) has been applied to two-phase/multi-phase flow measurement in recent years. Image reconstruction of CT often involves repeatedly solving large-dimensional matrix equations, which are computationally expensive, especially for the case of online flow regime identification. In this paper, minimum cross entropy reconstruction based on multi-resolution processing (MRMCE) is presented for oil–gas two-phase flow regime identification. A regularized MCE solution is obtained using the simultaneous multiplicative algebraic reconstruction technique (SMART) at a coarse resolution level, where important information on the reconstructed image is contained. Then, the solution in the finest resolution is obtained by inverse fast wavelet transformation. Both computer simulation and static/dynamic experiments were carried out for typical flow regimes. Results obtained indicate that the proposed method can dramatically reduce the computational time and improve the quality of the reconstructed image with suitable decomposition levels compared with the single-resolution maximum likelihood expectation maximization (MLEM), alternating minimization (AM), Landweber, iterative least square technique (ILST) and minimum cross entropy (MCE) methods. Therefore, the MRMCE method is suitable for identification of dynamic two-phase flow regimes

Critical solution for a Hill's type problem

International Nuclear Information System (INIS)

Cabral, Hildeberto; Castilho, Cesar

2001-08-01

We studied the problem of two satellites attracted by a center of force. Assuming the motion of the center of mass of the two satellites describes a keplerian circular motion around the center of force we regularized the collision between them using the Levi-Civita procedure. The existence of a constant of motion in the extended phase space allowed us to study the stability of the solution where the two satellites are tied together in their circular motion around the center of force. We call this solution the critical solution. A theorem of M Kummer is applied to prove, in specific conditions, the existence of two one-parametric families of almost periodic orbits for the satellites motion that bifurcates from the critical solution. (author)

High Tc superconductors using solution techniques

International Nuclear Information System (INIS)

Barboux, P.; Valente, I.; Henry, M.; Morineau, R.; Tarascon, J.M.; Khan, S.; Shokoohi, F.; Bagley, B.G.

1989-01-01

The authors have investigated different solution techniques to synthesize the Cu-based superconductors in the thick film form. Thick films of YBa 2 Cu 3 O 7 have been produced using controlled precipitation techniques. Bi-based and Tl-based materials have been deposited by spraying of ionic solutions. The numerous difficulties encountered during each process are analyzed in order to propose new synthesis procedures such as a new method, based on the precipitation of hydroxides only, which is described as a prospective for lowering the synthesis temperature and shortening the reaction time

On the physical solutions to the heat equation subjected to nonlinear boundary conditions

International Nuclear Information System (INIS)

Gama, R.M.S. da.

1990-01-01

This work consists of a discussion on the physical solutions to the steady-state heat transfer equation, when it is subjected to nonlinear boundary conditions. It will be presented a functional, whose minimum occurs for the (unique) physical solution to the condidered heat transfer problem, suitable for a large class of typical (nonlinear) boundary conditions (representing the radiative/convective loss from the body to the environment). It will be demonstrated that these problems admit-always one, and only one, physical solution (which represents the absolute temperature). (author)

HDPE (High Density Polyethylene) pipeline and riser design in Guanabara Bay: challenges and solutions

Energy Technology Data Exchange (ETDEWEB)

Bomfimsilva, Carlos; Jorge, Joao Paulo Carrijo; Schmid, Dominique; Gomes, Rodrigo Klim [INTECSEA, Sao Paulo, SP (Brazil); Lima, Alexander Piraja [GDK, Salvador, BA (Brazil)

2009-12-19

Worldwide shipments of plastic pipes are forecasted to increase 5.2% per year since 2008, being commonly used for water supply and sewage disposal. The HDPE (High Density Polyethylene) pipes have been applied recently to deliver potable water and fire fighting water for the main pier of the LNG system in Guanabara Bay, Rio de Janeiro. The system contains three sizes of pipe outside diameter, 110 mm and 160 mm for water supply, and 500 mm for the fire fighting system. The main design challenges of the pipeline system included providing on-bottom stability, a suitable installation procedure and a proper riser design. The on-bottom stability calculations, which are quite different from the conventional steel pipelines, were developed by designing concrete blocks to be assembled on the pipeline in a required spacing to assure long term stability, knowing that plastic pipes are buoyant even in flooded conditions. The installation procedure was developed considering the lay down methodology based on surface towing technique. The riser was designed to be installed together with additional steel support structure to allow the entire underwater system to have the same plastic pipe specification up to the surface. This paper presents the main challenges that were faced during the design of the HDPE pipelines for the LNG system in Guanabara Bay, addressing the solutions and recommendations adopted for the plastic underwater pipeline system.

A finite volume procedure for fluid flow, heat transfer and solid-body stress analysis

KAUST Repository

Jagad, P. I.; Puranik, B. P.; Date, A. W.

2018-01-01

A unified cell-centered unstructured mesh finite volume procedure is presented for fluid flow, heat transfer and solid-body stress analysis. An in-house procedure (A. W. Date, Solution of Transport Equations on Unstructured Meshes with Cell

Procedure for preparation of a Ausup(195m) containing liquid, procedure for the execution of a radiodiagnostic examination, and a radioisotope generator for generating a Ausup(195m) containing liquid

International Nuclear Information System (INIS)

1980-01-01

A procedure is described for the preparation of an Ausup(195m) containing fluid by adsorbing the parent isotope Hgsup(195m) onto an adsorption material and then eluting the radioactive daughter isotope Ausup(195m). The packing materials for the chromatographic column are silica gel, porous and massive glass beads. The adsorption materials for Hg 195 are hydrated manganese dioxide, silver, and zinc, cadmium, silver or zirconium sulfides. The procedure for depositing these materials in the packing material is outlined and the most suitable eluting fluid for each adsorption material is presented. The procedure has applications in the execution of a radiodiagnostic examination using an Ausup(195m) labelled fluid. (C.F.)

Sign-changing solutions for non-local elliptic equations

Directory of Open Access Journals (Sweden)

Huxiao Luo

2017-07-01

Full Text Available This article concerns the existence of sign-changing solutions for equations driven by a non-local integrodifferential operator with homogeneous Dirichlet boundary conditions, $$\\displaylines{ -\\mathcal{L}_Ku=f(x,u,\\quad x\\in \\Omega, \\cr u=0,\\quad x\\in \\mathbb{R}^n\\setminus\\Omega, }$$ where $\\Omega\\subset\\mathbb{R}^n\\; (n\\geq2$ is a bounded, smooth domain and the nonlinear term f satisfies suitable growth assumptions. By using Brouwer's degree theory and Deformation Lemma and arguing as in [2], we prove that there exists a least energy sign-changing solution. Our results generalize and improve some results obtained in [27

Dose measurement method suitable for management of food irradiation

International Nuclear Information System (INIS)

Tanaka, Ryuichi

1990-01-01

The report describes major features of dose measurement performed for the management of food irradiation processes, and dose measuring methods suitable for this purpose, and outlines some activities for establishing international standards for dose measurement. Traceability studies made recently are also reviewed. Compared with the sterilization of medical materials, food irradiation is different in some major points from a viewpoint of dose measurement: foods can undergo significant changes in bulk density, depending on its properties, during irradiation, and the variation in the uniformity of bulk density can be large within an irradiation unit and among different units. An accurate dosimeter and well-established traceability are essential for food irradiation control, and basically a dosimeter should be high in reproducibility and stable in dose response, and should be easy to readjust for eliminating systematic errors. A new type of dosimeter was developed recently, in which ESR is used to measure the free radicals generated by radiations in crystals of alanine, an amino acid. Standardization of large dose measurement procedures has been carried out by committee E10 set up under ASTM. (N.K.)

Some exact solutions for one-dimensional self-interacting systems in quantum field theories

International Nuclear Information System (INIS)

De Puy, R.J.

1975-01-01

Particular positive or negative frequency solutions of the field equation, (d 2 /dt 2 + m 2 )phi/sub q lambda/ + lambda phi/sub q lambda/ /sup 2q+1/ = 0, for which q not equal to 0, -1 are used in the study of one-dimensional quantum field theories. The commutator, [phi/sub q lambda/,d phi/sub q lambda//dt]/sub -/ = 1, is not applied because phi/sub q lambda/ is required to be a general solution. The commutator, [phi/sub q lambda//sup (+)/(t),phi/sub q lambda//sup (-)/(t)]/sub -/ = 1, cannot be applied to the particular solutions considered. The system is quantized by requiring that [phi/sub q lambda//sup (+)/(0),phi/sub q lambda//sup (-)/(0)]/sub -/ = 1 in analogy with the quantization procedure prescribed for free fields. This quantization procedure leads to a propagator which is not invariant with respect to time translations. Hence any connection between the procedure for quantizing nonlinear particular solutions and the linear canonical quantization formalism remains obscure. General solutions of the field equation, (d 2 /dt 2 + m 2 )phi + lambda phi 3 = 0, are patterned after solutions obtained by the method of successive approximations. These solutions process terms containing polynomial factors in the independent variable, t, known as secular terms which account for the unboundedness of the solutions for large magnitudes of the independent variable. Therefore the differential equation and its solution complete with secular terms are modified by making structural changes in both and by expanding the mass in operator-valued terms. The constituent operators of the solution and mass are chosen such that the secular terms are eliminated. The higher order terms in the mass operator are rewritten in terms of the field solution and its first derivative

Closed form solutions of two time fractional nonlinear wave equations

Science.gov (United States)

Akbar, M. Ali; Ali, Norhashidah Hj. Mohd.; Roy, Ripan

2018-06-01

In this article, we investigate the exact traveling wave solutions of two nonlinear time fractional wave equations. The fractional derivatives are described in the sense of conformable fractional derivatives. In addition, the traveling wave solutions are accomplished in the form of hyperbolic, trigonometric, and rational functions involving free parameters. To investigate such types of solutions, we implement the new generalized (G‧ / G) -expansion method. The extracted solutions are reliable, useful and suitable to comprehend the optimal control problems, chaotic vibrations, global and local bifurcations and resonances, furthermore, fission and fusion phenomena occur in solitons, the relativistic energy-momentum relation, scalar electrodynamics, quantum relativistic one-particle theory, electromagnetic interactions etc. The results reveal that the method is very fruitful and convenient for exploring nonlinear differential equations of fractional order treated in theoretical physics.

Flame atomic absorption spectrometric determination of heavy metals in aqueous solution and surface water preceded by co-precipitation procedure with copper(II) 8-hydroxyquinoline

Science.gov (United States)

Ipeaiyeda, Ayodele Rotimi; Ayoade, Abisayo Ruth

2017-12-01

Co-precipitation procedure has widely been employed for preconcentration and separation of metal ions from the matrices of environmental samples. This is simply due to its simplicity, low consumption of separating solvent and short duration for analysis. Various organic ligands have been used for this purpose. However, there is dearth of information on the application of 8-hydroxyquinoline (8-HQ) as ligand and Cu(II) as carrier element. The use of Cu(II) is desirable because there is no contamination and background adsorption interference. Therefore, the objective of this study was to use 8-HQ in the presence of Cu(II) for coprecipitation of Cd(II), Co(II), Cr(III), Ni(II) and Pb(II) from standard solutions and surface water prior to their determinations by flame atomic absorption spectrometry (FAAS). The effects of pH, sample volume, amount of 8-HQ and Cu(II) and interfering ions on the recoveries of metal ions from standard solutions were monitored using FAAS. The water samples were treated with 8-HQ under the optimum experimental conditions and metal concentrations were determined by FAAS. The metal concentrations in water samples not treated with 8-HQ were also determined. The optimum recovery values for metal ions were higher than 85.0%. The concentrations (mg/L) of Co(II), Ni(II), Cr(III), and Pb(II) in water samples treated with 8-HQ were 0.014 ± 0.002, 0.03 ± 0.01, 0.04 ± 0.02 and 0.05 ± 0.02, respectively. These concentrations and those obtained without coprecipitation technique were significantly different. Coprecipitation procedure using 8-HQ as ligand and Cu(II) as carrier element enhanced the preconcentration and separation of metal ions from the matrix of water sample.

Regularities of radium coprecipitation with barium sulfate from salt solutions

International Nuclear Information System (INIS)

Kudryavskij, Yu.P.; Rakhimova, O.V.

2007-01-01

Coprecipitation of radium with barium sulfate from highly concentrated NaCl solutions is studied, including the effects of the initial solution composition, alkaline reagent (CaO, NaOH), supporting electrolyte (NaCl) concentration, and pH. The process is promoted by high NaCl concentration in the initial solution, which is due to structural transformation and change in the sorption activity of the BaSO 4 precipitate in salt solutions. The results obtained were applied to recovery of radium from process solutions during the development and introduction of improved procedure for disinfection and decontamination of waste yielded by chlorination of loparite concentrates [ru

Process instrument monitoring for SNM solution surveillance

International Nuclear Information System (INIS)

Armatys, C.M.; Johnson, C.E.; Wagner, E.P.

1983-02-01

A process monitoring computer system at the Idaho Chemical Processing Plant (ICPP) is being used to evaluate nuclear fuel reprocessing plant data for Safeguards surveillance capabilities. The computer system was installed to collect data from the existing plant instruments and to evaluate what safeguards assurances can be provided to complement conventional accountability and physical protection measures. Movements of solutions containing special nuclear material (SNM) can be observed, activities associated with accountancy measurements (mixing, sampling, and bulk measurement) can be confirmed, and long-term storage of SNM solutions can be monitored to ensure containment. Special precautions must be taken, both in system design and operation to ensure adequate coverage of essential measured parameters and interpretation of process data, which can be comprised by instrument malfunctions or failures, unreliable data collection, or process activities that deviate from readily identified procedures. Experience at ICPP and prior evaluations at the Tokai reprocessing plant show that the use of process data can provide assurances that accountability measurement procedures are followed and SNM solutions are properly contained and can help confirm that SNM controls are in effect within a facility

Nonlocal symmetry generators and explicit solutions of some partial differential equations

International Nuclear Information System (INIS)

Qin Maochang

2007-01-01

The nonlocal symmetry of a partial differential equation is studied in this paper. The partial differential equation written as a conservation law can be transformed into an equivalent system by introducing a suitable potential. The nonlocal symmetry group generators of original partial differential equations can be obtained through their equivalent system. Further, new explicit solutions can be constructed from the newly obtained symmetry generators. The Burgers equation is chosen as an example; many new valuable explicit solutions and nonlocal symmetry generators are presented

A decision support system for identifying abnormal operating procedures in a nuclear power plant

International Nuclear Information System (INIS)

Hsieh, Min-Han; Hwang, Sheue-Ling; Liu, Kang-Hong; Liang, Sheau-Farn Max; Chuang, Chang-Fu

2012-01-01

Highlights: ► A decision support system has been constructed and verified. ► The operator's decision-making time was decreased by about 25%. ► The accuracy was increased by about 18%. ► The system prevents overlooking important information. ► Fewer erroneous solutions were implemented, and the mental workload was reduced. - Abstract: In order to prevent safety hazards that can result from inappropriate decisions made by the operators of a nuclear power plant (NPP), this study was undertaken to develop a decision support system to reduce the complexity of the decision-making process by aiding operators’ cognitive activities, integrating unusual symptoms, and identifying the most suitable abnormal operating procedure (AOP) for operators. The study was conducted from the perspective of human factors engineering in order to compare the process that operators originally used to select an AOP with a process that included a support system for AOP identification. The results of the study indicated that the existence of a support system reduces errors by quickly suggesting likely AOPs. With such a support system in place, there were clear improvements in human performance, i.e., decision-making time decreased by about 25%, and the accuracy of the operators’ decisions, judged by the successful resolution of specific problems, increased by about 18%. In addition, there were fewer erroneous solutions implemented, and the mental workload was reduced. Hence, the decision support system is proposed as a training tool in identifying AOPs in the main control room (MCR).

A study on the multiple solutions of the Martree-Fock-Roothaan equation for closed shell systems

International Nuclear Information System (INIS)

Malbouisson, L.A.C.

1985-01-01

An analysis of the multiple solutions of the Hartree-Fock-Roothaan equation for closed shell systems is done. The meaning of these solutions is discussed as self-consistent solutions of the pseudo-eingen-value equation and a general method for obtaining them is proposed. It is developed a criterion of stability for classifying the solutions depending on the type of the extremum point of the electronic energy function that the solution represent. It is also shown the existence of a correspondence between the multiple solutions and the several ordering rules that can be introduced for the usual iterative procedure of resolution of the equation. All the analysis and procedures developed are applied to the systems LiH, BH, Be and He. (author) [pt

Anisotropic generalization of well-known solutions describing relativistic self-gravitating fluid systems. An algorithm

Energy Technology Data Exchange (ETDEWEB)

Thirukkanesh, S. [Eastern University, Department of Mathematics, Chenkalady (Sri Lanka); Ragel, F.C. [Eastern University, Department of Physics, Chenkalady (Sri Lanka); Sharma, Ranjan; Das, Shyam [P.D. Women' s College, Department of Physics, Jalpaiguri (India)

2018-01-15

We present an algorithm to generalize a plethora of well-known solutions to Einstein field equations describing spherically symmetric relativistic fluid spheres by relaxing the pressure isotropy condition on the system. By suitably fixing the model parameters in our formulation, we generate closed-form solutions which may be treated as an anisotropic generalization of a large class of solutions describing isotropic fluid spheres. From the resultant solutions, a particular solution is taken up to show its physical acceptability. Making use of the current estimate of mass and radius of a known pulsar, the effects of anisotropic stress on the gross physical behaviour of a relativistic compact star is also highlighted. (orig.)

Variations in peak nasal inspiratory flow among healthy students after using saline solutions.

Science.gov (United States)

Olbrich Neto, Jaime; Olbrich, Sandra Regina Leite Rosa; Mori, Natália Leite Rosa; Oliveira, Ana Elisa de; Corrente, José Eduardo

2016-01-01

Nasal hygiene with saline solutions has been shown to relieve congestion, reduce the thickening of the mucus and keep nasal cavity clean and moist. Evaluating whether saline solutions improve nasal inspiratory flow among healthy children. Students between 8 and 11 years of age underwent 6 procedures with saline solutions at different concentrations. The peak nasal inspiratory flow was measured before and 30 min after each procedure. Statistical analysis was performed by means of t test, analysis of variance, and Tukey's test, considering p<0.05. We evaluated 124 children at all stages. There were differences on the way a same concentration was used. There was no difference between 0.9% saline solution and 3% saline solution by using a syringe. The 3% saline solution had higher averages of peak nasal inspiratory flow, but it was not significantly higher than the 0.9% saline solution. It is important to offer various options to patients. Copyright © 2015 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

UTBB FDSOI suitability for IoT applications: Investigations at device, design and architectural levels

Science.gov (United States)

Berthier, Florent; Beigne, Edith; Heitzmann, Frédéric; Debicki, Olivier; Christmann, Jean-Frédéric; Valentian, Alexandre; Billoint, Olivier; Amat, Esteve; Morche, Dominique; Chairat, Soundous; Sentieys, Olivier

2016-11-01

In this paper, we propose to analyze Ultra Thin Body and Box FDSOI technology suitability and architectural solutions for IoT applications and more specifically for autonomous Wireless Sensor Nodes (WSNs). As IoT applications are extremely diversified there is a strong need for flexible solutions at design, architectural level but also at technological level. Moreover, as most of those systems are recovering their energy from the environment, they are challenged by low voltage supplies and low leakage functionalities. We detail in this paper some Ultra Thin Body and Box FDSOI 28 nm characteristics and results demonstrating that this technology could be a perfect option for multidisciplinary IoT devices. Back biasing capabilities and low voltage features are investigated demonstrating efficient high speed/low leakage flexibility. In addition, architectural solutions for WSNs microcontroller are also proposed taking advantage of Ultra Thin Body and Box FDSOI characteristics for full user applicative flexibility. A partitioned architecture between an Always Responsive part with an asynchronous Wake Up Controller (WUC) managing WSN current tasks and an On Demand part with a main processor for application maintenance is presented. First results of the Always Responsive part implemented in Ultra Thin Body and Box FDSOI 28 nm are also exposed.

The use of potassium hydroxide (KOH) solution as a suitable approach to isolate plastics ingested by marine organisms

NARCIS (Netherlands)

Kühn, Susanne; Werven, Van Bernike; Oyen, Van Albert; Meijboom, André; Bravo Rebolledo, Elisa L.; Franeker, Van Jan A.

2017-01-01

In studies of plastic ingestion by marine wildlife, visual separation of plastic particles from gastrointestinal tracts or their dietary content can be challenging. Earlier studies have used solutions to dissolve organic materials leaving synthetic particles unaffected. However, insufficient tests

Uranium in aqueous solutions by colorimetry

International Nuclear Information System (INIS)

Anon.

1981-01-01

The method covers the quantitative determination of uranium in known volumes of aqueous solutions that contain radioactive nuclides. These solutions arise from processing of irradiated nuclear fuel and from laboratory studies on irradiated uranium. The method is applicable to solutions containing a minimum of 30 μg of uranium per sample although as little as 0.5 μg can be detected but with lower precision. Highest precision is obtained with 50 to 75 μg of uranium in the test sample. Dilutions must be made at concentrations above 750 μg/ml. The method includes a discussion of photometers and photometric practice, apparatus, reagents, cell matching, preparation of standard curves, calibration by the method of internal standards, procedure, calculation, and precision

A procedure to construct exact solutions of nonlinear fractional differential equations.

Science.gov (United States)

Güner, Özkan; Cevikel, Adem C

2014-01-01

We use the fractional transformation to convert the nonlinear partial fractional differential equations with the nonlinear ordinary differential equations. The Exp-function method is extended to solve fractional partial differential equations in the sense of the modified Riemann-Liouville derivative. We apply the Exp-function method to the time fractional Sharma-Tasso-Olver equation, the space fractional Burgers equation, and the time fractional fmKdV equation. As a result, we obtain some new exact solutions.

Process for manufacture of a catalyst suitable for the steam reforming of hydrocarbons and for obtaining methane

Energy Technology Data Exchange (ETDEWEB)

Golebiowski, A.; Romotowski, T.; Hennel, W.; Wroblewska-Wroblewska, T.; Polanski, A.; Janecki, Z.; Paluch-Paluch, S.

1982-07-29

The invention concerns a process for the manufacture of a catalyst suitable for the steam reforming of hydrocarbons or for obtaining methane, by the deposition of the catalytic components on a metal carrier with a large surface area, particularly a process for the manufacture of a solid nickel catalyst, which is suitable for the steam reforming of hydrocarbons, particularly of methane. The following steps of the process are carried out: producing a highly porous layer of spongy metal from Ni powder on the side of a metal wall away from a heat medium, which separates the reaction mixture from the heat medium, then separate application of a non-reducing oxide (Al/sub 2/O/sub 3/) and a reducing oxide (nickel oxide) on the spongy metal by soaking with metal salt solution and then roasting in the temperature range of 400 to 1200/sup 0/C.

Establishing the traceability of a uranyl nitrate solution to a standard reference material

International Nuclear Information System (INIS)

Jackson, C.H.; Clark, J.P.

1978-01-01

A uranyl nitrate solution for use as a Working Calibration and Test Material (WCTM) was characterized, using a statistically designed procedure to document traceability to National Bureau of Standards Reference Material (SPM-960). A Reference Calibration and Test Material (PCTM) was prepared from SRM-960 uranium metal to approximate the acid and uranium concentration of the WCTM. This solution was used in the characterization procedure. Details of preparing, handling, and packaging these solutions are covered. Two outside laboratories, each having measurement expertise using a different analytical method, were selected to measure both solutions according to the procedure for characterizing the WCTM. Two different methods were also used for the in-house characterization work. All analytical results were tested for statistical agreement before the WCTM concentration and limit of error values were calculated. A concentration value was determined with a relative limit of error (RLE) of approximately 0.03% which was better than the target RLE of 0.08%. The use of this working material eliminates the expense of using SRMs to fulfill traceability requirements for uranium measurements on this type material. Several years' supply of uranyl nitrate solution with NBS traceability was produced. The cost of this material was less than 10% of an equal quantity of SRM-960 uranium metal

Thorium determination by X-ray Fluorescence Spectrometry in simulated thorex process solutions

International Nuclear Information System (INIS)

Yamaura, M.; Matsuda, H.T.

1989-01-01

The X-ray fluorescence method for thorium determination in aqueous and organic (TBP-n-dodecane) solutions is described. The thin film-technique for sample preparation and a suitable internal standard have been used. Some parameters as analytical line, internal standard, filter paper, paper geometry, sample volume and measurement conditions were studied. Uranium, fission products, corrosion products and thorex reagent components were studied as interfering elements in the thorium analysis, as well as the matrix effect by using the thorex process simulated solutions the method to thorium determination in irradiated thorium solutions was applied. (M.J.C.) [pt

Influence of synthesis procedure on the formation and properties of zinc oxide

International Nuclear Information System (INIS)

Music, S.; Popovic, S.; Maljkovic, M.; Dragcevic, D.

2002-01-01

Formation and properties of zinc oxide were investigated in dependence on the synthesis procedure. Zinc oxide did not crystallize upon hydrothermal treatment of Zn(NO 3 ) 2 aqueous solutions containing urea, up to 160 deg. C. Hydrozincite was formed instead. Changes in the X-ray diffraction patterns and Fourier transform infrared (FT-IR) spectra were interpreted in terms of stacking disorder in hydrozincite crystals. Zinc oxide powder was obtained by thermal treatment in air of precipitated hydrozincite. The conditions for instantaneous synthesis of very fine zinc oxide particles were found. This procedure is based on addition of TMAH (tetramethylammonium hydroxide) solution to an ethanolic solution of zinc acetate dihydrate, up to pH∼14. On the other hand, addition of an equivalent volume of water to the ethanolic solution of zinc acetate dihydrate, prior to the addition of TMAH solution up to pH∼14, yielded ZnO flakes without any specific shape. All zinc oxide particles produced upon heating at 600 deg. C in air showed similar morphology and tendency to aggregation due to the sintering effect. The features of the FT-IR spectra of zinc oxide particles were related to their shapes

Procedure of non-contacting local mass density and mass density distribution measurements

International Nuclear Information System (INIS)

Menzel, M.; Winkler, K.

1985-01-01

The invention has been aimed at a procedure of non-contacting local mass density and/or mass density distribution measurements i.e. without the interfering influence of sensors or probes. It can be applied to installations, apparatuses and pipings of chemical engineering, to tank constructions and transportation on extreme temperature and/or pressure conditions and aggressive media influences respectively. The procedure has utilized an ionizing quantum radiation whereby its unknown weakening and scattering is compensated by a suitable combination of scattering and transmission counter rate measurements in such a way that the local mass densities and the mass density distribution respectively are determinable

Procedure for obtaining neutron diffusion coefficients from neutron transport Monte Carlo calculations (AWBA Development Program)

International Nuclear Information System (INIS)

Gast, R.C.

1981-08-01

A procedure for defining diffusion coefficients from Monte Carlo calculations that results in suitable ones for use in neutron diffusion theory calculations is not readily obtained. This study provides a survey of the methods used to define diffusion coefficients from deterministic calculations and provides a discussion as to why such traditional methods cannot be used in Monte Carlo. This study further provides the empirical procedure used for defining diffusion coefficients from the RCP01 Monte Carlo program

Development of a vinasse nutritive solution for hydroponics.

Science.gov (United States)

dos Santos, José Darcy; Lopes da Silva, André Luís; da Luz Costa, Jefferson; Scheidt, Gessiel Newton; Novak, Alessandra Cristine; Sydney, Eduardo Bittencourt; Soccol, Carlos Ricardo

2013-01-15

Vinasse is a residue that originates from the distillation of fuel alcohol. However, it contains a relative amount of nutrients. The aim of this work was to develop a nutritive solution using vinasse and to compare it with a commercial solution for the cultivation of lettuce, watercress and rocket. Vinasse obtained from juice must was decanted and filtered, followed by chemical analyses of the nutrients. A nutritive solution composed of 10% vinasse supplemented with nutrients was in agreement with the results of the chemical analyses (a similar amount of Furlani's solution). Experiments were then performed in an NFT (Nutrient film technique) system. The treatments used the vinasse solution and a commercial solution constituted from a Yara Fertilizantes(®) product. The height of the aerial part and the number of leaves of the crops were evaluated at 7, 14, 21, 28, 35 and 42 days. In most crops, the results were very similar. The vinasse solution promoted a larger number of leaves in lettuce and the highest aerial part in watercress. For the rocket, there were no significant differences between the two solutions. In conclusion, a nutritive solution was developed using vinasse, and this solution provided suitable growth, which was higher in some cases, for the crops studied herein. This study shows the great potential of this technology as a rational alternative to vinasse disposal. Copyright © 2012 Elsevier Ltd. All rights reserved.

The design of operating procedures manuals for nuclear power plants

International Nuclear Information System (INIS)

Bohr, E.; Preuss, W.; Reinartz, G.; Thau, G.

1977-03-01

This report describes the findings of a research on the desirable design of operating procedures manuals for nuclear power plants. The work was supported by a grant of the Federal Department of the Interior. Information was acquired from different sources. Interviews and discussions on manual design were carried out with manual users in nuclear power plants. Moreover, tasks carried out using procedures were either observed or, alternatively, the manner of using procedures was elicited by interviews. In addition, manual writers, managers from manufacturers and utilities, nuclear experts, and individuals involved in manual specification activities were interviewed. A major source of information has been the pertinent scientific and technical findings scattered in the literature on topics such as instructional technology, engineering psychology, psycholinguistics, and typography. A comprehensive bibliography is included. General rules are established on designing instructional material for use on the job, aiming at increasing their legability, comprehensibility, and suitability to guide human performance. The application of these rules to the design of individual operating procedures is demonstrated. Recommendations are given on the design, layout, development and implementation of manuals. (orig.) [de

Determining the suitability of materials for disposal at sea under the London Convention 1972: A radiological assessment procedure

International Nuclear Information System (INIS)

2003-10-01

on conducting specific assessments to determine whether candidate materials for disposal at sea contained de minimis levels of radioactivity. This report contains guidance on performing specific assessments of candidate materials to determine whether the materials are de minimis in the meaning of the London Convention 1972. It follows the guidelines adopted by the Twenty-first Consultative Meeting of the London Convention 1972 that incorporate a Stepwise Evaluation Procedure for screening candidate material to determine if it can be treated as 'non-radioactive' (i.e. de minimis) under the Convention. Material that cannot be readily defined as de minimis on the basis of Steps 1 to 5 of the Stepwise Evaluation Procedure require a specific assessment at Step 6. Such an assessment is the subject of this report. The assessment process described in this report is based on an inherently conservative procedure consistent with the precautionary approach, provided for under the London Convention 1972. Its purpose is to ensure the use of conservative models and cautious assumptions that result in the overestimation of the doses due to candidate materials that might be disposed of at sea in near coastal waters under de minimis provisions. Accordingly, the radiological consequences of disposal at sea of de minimis materials in other areas of the continental shelf and deeper waters will result in much lower radiation exposures than those considered here. It must be stressed that any candidate materials designated as de minimis must comply with all other provisions of the Convention. Section 2 provides a summary of the Stepwise Evaluation Procedure as detailed in the guidelines and background information necessary to understand the context of this guidance. Section 3 describes in detail a procedure to conduct the specific radiological assessment of the disposal of a candidate material. It contains a schematic diagram illustrating the specific assessment process and components of

Extension of the segment-based Wilson and NRTL models for correlation of excess molar enthalpies of polymer solutions

International Nuclear Information System (INIS)

Sadeghi, Rahmat

2005-01-01

The polymer Wilson model and the polymer NRTL model have been extended for the representation of the excess enthalpy of multicomponent polymer solutions. Applicability of obtained equations in the correlation of the excess enthalpies of polymer solutions has been examined. It is found that the both models are suitable models in representing the published excess enthalpy data for the tested polymer solutions

N-body scattering solution in coordinate space

International Nuclear Information System (INIS)

Cheng-Guang, B.

1986-01-01

The Schroedinger equation has been transformed into a set of coupled partial differential equations having hyper-variables as arguments and a procedure for embedding the boundary conditions into the N-body scattering solution by using a set of homogeneous linear algebraic equations is proposed

Wheat Farmer's Land Consolidation Attitude and Suitable Solutions from Their Viewpoints in (Case Study: Hashtrood Township Rural Area

Directory of Open Access Journals (Sweden)

Ali Shams

2015-08-01

Full Text Available Proper planning and implementation of sound programs and strategies is vital to  agricultural development. Recognizing current problems and strengths of any section is required in the first step. One of the most important problems in the Iranian agriculture sector is land fragmentation. The purpose of this descriptive-correlational study was to investigate wheat farmers’ attitude and land consolidation solutions from their viewpoints in the Hashtrood Township in year 2013. A group of experts from different majors confirmed the validity of the questionnaire used as our research tool and by conducting a pilot test and the Cronbach’s alpha was calculated to be equal to 0.85 for attitude scale and 0.8 for solution scale, and hence its reliability was verified. The target population consisted of all of the wheat farmers in the Hashtrood Township in the East Azerbaijan province 186 of whom  were selected as samples from 15 villages based on Cochran’s sampling formula and the multi stage randomized sampling method. An analysis of the attitudes of wheat farmers revealed that 67.7 and 32.3 percent of them have unfavorable and neutral attitudes towards land consolidation. Also, there is a significant positive relationship between farming experience and their attitude in land consolidation, but there is a negative relationship between it and their total land segments.  Factor analysis of data revealed that four factors named as deterrent actions, cooperative-common actions, supportive-infrastructural actions and motivational extension actions explained 59.9% of land consolidation solutions by wheat farmers.

Hilbert's seventh problem solutions and extensions

CERN Document Server

Tubbs, Robert

2016-01-01

This exposition is primarily a survey of the elementary yet subtle innovations of several mathematicians between 1929 and 1934 that led to partial and then complete solutions to Hilbert’s Seventh Problem (from the International Congress of Mathematicians in Paris, 1900). This volume is suitable for both mathematics students, wishing to experience how different mathematical ideas can come together to establish results, and for research mathematicians interested in the fascinating progression of mathematical ideas that solved Hilbert’s problem and established a modern theory of transcendental numbers. .

Experimental setup and procedure for the measurement of the {sup 7}Be(n,α)α reaction at n-TOF

Energy Technology Data Exchange (ETDEWEB)

Cosentino, L. [INFN Laboratori Nazionali del Sud, Catania (Italy); Musumarra, A. [INFN Laboratori Nazionali del Sud, Catania (Italy); Dipartimento di Fisica e Astronomia DFA, Università di Catania (Italy); Barbagallo, M. [INFN Sezione di Bari (Italy); Pappalardo, A. [INFN Laboratori Nazionali del Sud, Catania (Italy); Colonna, N.; Damone, L. [INFN Sezione di Bari (Italy); Piscopo, M. [INFN Laboratori Nazionali del Sud, Catania (Italy); Finocchiaro, P., E-mail: FINOCCHIARO@LNS.INFN.IT [INFN Laboratori Nazionali del Sud, Catania (Italy); Maugeri, E.; Heinitz, S.; Schumann, D.; Dressler, R.; Kivel, N. [Paul Scherrer Institut, Nuclear Energy and Safety Research Department, 5232 Villigen (Switzerland); Aberle, O. [CERN, Geneva (Switzerland); Andrzejewski, J. [Uniwersytet Łódzki, Lodz (Poland); Audouin, L. [Institut de Physique Nucléaire, CNRS-IN2P3, Univ. Paris-Sud, Université Paris-Saclay, 91406 Orsay Cedex (France); Ayranov, M. [European Commission, DG-Energy (Luxembourg); Bacak, M. [Atominstitut der Österreichischen Universitäten, Technische Universität Wien (Austria); Barros, S. [C2TN-Instituto Superior Tecníco, Universidade de Lisboa (Portugal); Balibrea-Correa, J. [Centro de Investigaciones Energeticas Medioambientales y Tecnológicas (CIEMAT), Madrid (Spain); and others

2016-09-11

The newly built second experimental area EAR2 of the n-TOF spallation neutron source at CERN allows to perform (n, charged particles) experiments on short-lived highly radioactive targets. This paper describes a detection apparatus and the experimental procedure for the determination of the cross-section of the {sup 7}Be(n,α)α reaction, which represents one of the focal points toward the solution of the cosmological Lithium abundance problem, and whose only measurement, at thermal energy, dates back to 1963. The apparently unsurmountable experimental difficulties stemming from the huge {sup 7}Be γ-activity, along with the lack of a suitable neutron beam facility, had so far prevented further measurements. The detection system is subject to considerable radiation damage, but is capable of disentangling the rare reaction signals from the very high background. This newly developed setup could likely be useful also to study other challenging reactions requiring the detectors to be installed directly in the neutron beam.

Polymer-assisted metal deposition (PAMD): a full-solution strategy for flexible, stretchable, compressible, and wearable metal conductors.

Science.gov (United States)

Yu, You; Yan, Casey; Zheng, Zijian

2014-08-20

Metal interconnects, contacts, and electrodes are indispensable elements for most applications of flexible, stretchable, and wearable electronics. Current fabrication methods for these metal conductors are mainly based on conventional microfabrication procedures that have been migrated from Si semiconductor industries, which face significant challenges for organic-based compliant substrates. This Research News highlights a recently developed full-solution processing strategy, polymer-assisted metal deposition (PAMD), which is particularly suitable for the roll-to-roll, low-cost fabrication of high-performance compliant metal conductors (Cu, Ni, Ag, and Au) on a wide variety of organic substrates including plastics, elastomers, papers, and textiles. This paper presents i) the principles of PAMD, and how to use it for making ii) flexible, stretchable, and wearable conductive metal electrodes, iii) patterned metal interconnects, and d) 3D stretchable and compressible metal sponges. A critical perspective on this emerging strategy is also provided. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Commissioning Procedures for Mechanical Precision and Accuracy in a Dedicated LINAC

International Nuclear Information System (INIS)

Ballesteros-Zebadua, P.; Larrga-Gutierrez, J. M.; Garcia-Garduno, O. A.; Juarez, J.; Prieto, I.; Moreno-Jimenez, S.; Celis, M. A.

2008-01-01

Mechanical precision measurements are fundamental procedures for the commissioning of a dedicated LINAC. At our Radioneurosurgery Unit, these procedures can be suitable as quality assurance routines that allow the verification of the equipment geometrical accuracy and precision. In this work mechanical tests were performed for gantry and table rotation, obtaining mean associated uncertainties of 0.3 mm and 0.71 mm, respectively. Using an anthropomorphic phantom and a series of localized surface markers, isocenter accuracy showed to be smaller than 0.86 mm for radiosurgery procedures and 0.95 mm for fractionated treatments with mask. All uncertainties were below tolerances. The highest contribution to mechanical variations is due to table rotation, so it is important to correct variations using a localization frame with printed overlays. Mechanical precision knowledge would allow to consider the statistical errors in the treatment planning volume margins

Cell-based land use screening procedure for regional siting analysis

International Nuclear Information System (INIS)

Jalbert, J.S.; Dobson, J.E.

1976-01-01

An energy facility site-screening methodology which permits the land resource planner to identify candidate siting areas was developed. Through the use of spatial analysis procedures and computer graphics, a selection of candidate areas is obtained. Specific sites then may be selected from among candidate areas for environmental impact analysis. The computerized methodology utilizes a cell-based geographic information system for specifying the suitability of candidate areas for an energy facility. The criteria to be considered may be specified by the user and weighted in terms of importance. Three primary computer programs have been developed. These programs produce thematic maps, proximity calculations, and suitability calculations. Programs are written so as to be transferrable to regional planning or regulatory agencies to assist in rational and comprehensive power plant site identification and analysis

Four-center bubbled BPS solutions with a Gibbons-Hawking base

Science.gov (United States)

Heidmann, Pierre

2017-10-01

We construct four-center bubbled BPS solutions with a Gibbons-Hawking base space. We give a systematic procedure to build scaling solutions: starting from three-supertube configurations and using generalized spectral flows and gauge transformations to extend to solutions with four Gibbons-Hawking centers. This allows us to construct very large families of smooth horizonless solutions that have the same charges and angular momentum as supersymmetric black holes with a macroscopically large horizon area. Our construction reveals that all scaling solutions with four Gibbons Hawking centers have an angular momentum at around 99% of the cosmic censorship bound. We give both an analytical and a numerical explanation for this unexpected feature.

EXTRACTION OF URANYL NITRATE FROM AQUEOUS SOLUTIONS

Science.gov (United States)

Furman, N.H.; Mundy, R.J.

1957-12-10

An improvement in the process is described for extracting aqueous uranyl nitrate solutions with an organic solvent such as ether. It has been found that the organic phase will extract a larger quantity of uranyl nitrate if the aqueous phase contains in addition to the uranyl nitrate, a quantity of some other soluble nitrate to act as a salting out agent. Mentioned as suitable are the nitrates of lithium, calcium, zinc, bivalent copper, and trivalent iron.

PARALLEL SOLUTION METHODS OF PARTIAL DIFFERENTIAL EQUATIONS

Directory of Open Access Journals (Sweden)

Korhan KARABULUT

1998-03-01

Full Text Available Partial differential equations arise in almost all fields of science and engineering. Computer time spent in solving partial differential equations is much more than that of in any other problem class. For this reason, partial differential equations are suitable to be solved on parallel computers that offer great computation power. In this study, parallel solution to partial differential equations with Jacobi, Gauss-Siedel, SOR (Succesive OverRelaxation and SSOR (Symmetric SOR algorithms is studied.

Closed form solutions of two time fractional nonlinear wave equations

Directory of Open Access Journals (Sweden)

M. Ali Akbar

2018-06-01

Full Text Available In this article, we investigate the exact traveling wave solutions of two nonlinear time fractional wave equations. The fractional derivatives are described in the sense of conformable fractional derivatives. In addition, the traveling wave solutions are accomplished in the form of hyperbolic, trigonometric, and rational functions involving free parameters. To investigate such types of solutions, we implement the new generalized (G′/G-expansion method. The extracted solutions are reliable, useful and suitable to comprehend the optimal control problems, chaotic vibrations, global and local bifurcations and resonances, furthermore, fission and fusion phenomena occur in solitons, the relativistic energy-momentum relation, scalar electrodynamics, quantum relativistic one-particle theory, electromagnetic interactions etc. The results reveal that the method is very fruitful and convenient for exploring nonlinear differential equations of fractional order treated in theoretical physics. Keywords: Traveling wave solution, Soliton, Generalized (G′/G-expansion method, Time fractional Duffing equation, Time fractional Riccati equation

Analytical solutions for systems of partial differential-algebraic equations.

Science.gov (United States)

Benhammouda, Brahim; Vazquez-Leal, Hector

2014-01-01

This work presents the application of the power series method (PSM) to find solutions of partial differential-algebraic equations (PDAEs). Two systems of index-one and index-three are solved to show that PSM can provide analytical solutions of PDAEs in convergent series form. What is more, we present the post-treatment of the power series solutions with the Laplace-Padé (LP) resummation method as a useful strategy to find exact solutions. The main advantage of the proposed methodology is that the procedure is based on a few straightforward steps and it does not generate secular terms or depends of a perturbation parameter.

A mixed implicit/explicit procedure for soil-structure interaction

International Nuclear Information System (INIS)

Kunar, R.R.

1982-01-01

This paper describes an efficient method for the solution of dynamic soil-structure interaction problems. The method which combines implicit and explicit time integration procedures is ideally suited to problems in which the structure is considered linear and the soil non-linear. The equations relating to the linear structures are integrated using an unconditionally stable implicit scheme while the non-linear soil is treated explicitly. The explicit method is ideally suited to non-linear calculations as there is no need for iterative techniques. The structural equations can also be integrated explicitly, but this generally requires a time step that is much smaller than that for the soil. By using an unconditionally stable implicit algorithm for the structure, the complete analysis can be performed using the time step for the soil. The proposed procedure leads to economical solutions with the soil non-linearities handled accurately and efficiently. (orig.)

Control of PbI2 nucleation and crystallization: towards efficient perovskite solar cells based on vapor-assisted solution process

Science.gov (United States)

Yang, Chongqiu; Peng, Yanke; Simon, Terrence; Cui, Tianhong

2018-04-01

Perovskite solar cells (PSC) have outstanding potential to be low-cost, high-efficiency photovoltaic devices. The PSC can be fabricated by numerous techniques; however, the power conversion efficiency (PCE) for the two-step-processed PSC falls behind that of the one-step method. In this work, we investigate the effects of relative humidity (RH) and dry air flow on the lead iodide (PbI2) solution deposition process. We conclude that the quality of the PbI2 film is critical to the development of the perovskite film and the performance of the PSC device. Low RH and dry air flow used during the PbI2 spin coating procedure can increase supersaturation concentration to form denser PbI2 nuclei and a more suitable PbI2 film. Moreover, airflow-assisted PbI2 drying and thermal annealing steps can smooth transformation from the nucleation stage to the crystallization stage.

Procedure Improvement in Blood Processing for Chromosome Aberration Analyst

International Nuclear Information System (INIS)

Noraisyah Mohd Yusof; Juliana Mahamad; Rahimah Abd Rahim; Yahaya Talib; Mohd Rodzi Ali

2015-01-01

Detection of chromosome at metaphase of the cell cycle is performed either manually or automatically. Procedure for slide preparation published by the IAEA does not guarantee that the quality of slide is suitable for automatic detection. The detection efficiency reduces if there is cells debris on slides. This paper describes the modifications made to the standard procedure. The period of hypotonic treatment to the cell was lengthened; the slides were pre-treated with RNase and the frequency of rinsing during the chromosomal coloring process was increased. Results show the metaphase images were better and clearer, and numbers of metaphase that can be detected automatically were also increased. In conclusion, modification to the current standard protocol helps to easy the process of chromosome aberration analysis at Nuclear Malaysia. (author)

On exact solitary wave solutions of the nonlinear Schroedinger equation with a source

International Nuclear Information System (INIS)

Raju, T Solomon; Kumar, C Nagaraja; Panigrahi, Prasanta K

2005-01-01

We use a fractional transformation to connect the travelling wave solutions of the nonlinear Schroedinger equation (NLSE), phase locked with a source, to the elliptic equations satisfying, f-Prime ± af ± λf 3 = 0. The solutions are necessarily of rational form, containing both trigonometric and hyperbolic types as special cases. Bright and dark solitons, as well as singular solitons, are obtained in a suitable range of parameter values. (letter to the editor)

Exploration of polyelectrolytes as draw solutes in forward osmosis processes

KAUST Repository

Ge, Qingchun

2012-03-01

The development of the forward osmosis (FO) process has been constrained by the slow development of appropriate draw solutions. Two significant concerns related to draw solutions are the draw solute leakage and intensiveenergy requirement in recycling draw solutes after the FO process. FO would be much attractive if there is no draw solute leakage and the recycle of draw solutes is easy and economic. In this study, polyelectrolytes of a series of polyacrylic acid sodium salts (PAA-Na), were explored as draw solutes in the FO process. The characteristics of high solubility in water and flexibility in structural configuration ensure the suitability of PAA-Na as draw solutes and their relative ease in recycle through pressure-driven membrane processes. The high water flux with insignificant salt leakage in the FO process and the high salt rejection in recycle processes reveal the superiority of PAA-Na to conventional ionic salts, such as NaCl, when comparing their FO performance via the same membranes. The repeatable performance of PAA-Na after recycle indicates the absence of any aggregation problems. The overall performance demonstrates that polyelectrolytes of PAA-Na series are promising as draw solutes, and the new concept of using polyelectrolytes as draw solutes in FO processes is applicable. © 2011 Elsevier Ltd.

Asymptotically optimum multialternative sequential procedures for discernment of processes minimizing average length of observations

Science.gov (United States)

Fishman, M. M.

1985-01-01

The problem of multialternative sequential discernment of processes is formulated in terms of conditionally optimum procedures minimizing the average length of observations, without any probabilistic assumptions about any one occurring process, rather than in terms of Bayes procedures minimizing the average risk. The problem is to find the procedure that will transform inequalities into equalities. The problem is formulated for various models of signal observation and data processing: (1) discernment of signals from background interference by a multichannel system; (2) discernment of pulse sequences with unknown time delay; (3) discernment of harmonic signals with unknown frequency. An asymptotically optimum sequential procedure is constructed which compares the statistics of the likelihood ratio with the mean-weighted likelihood ratio and estimates the upper bound for conditional average lengths of observations. This procedure is shown to remain valid as the upper bound for the probability of erroneous partial solutions decreases approaching zero and the number of hypotheses increases approaching infinity. It also remains valid under certain special constraints on the probability such as a threshold. A comparison with a fixed-length procedure reveals that this sequential procedure decreases the length of observations to one quarter, on the average, when the probability of erroneous partial solutions is low.

Catalyzed reduction of nitrate in aqueous solutions

International Nuclear Information System (INIS)

Haas, P.A.

1994-08-01

Sodium nitrate and other nitrate salts in wastes is a major source of difficulty for permanent disposal. Reduction of nitrate using aluminum metal has been demonstrated, but NH 3 , hydrazine, or organic compounds containing oxygen would be advantageous for reduction of nitrate in sodium nitrate solutions. Objective of this seed money study was to determine minimum conditions for reduction. Proposed procedure was batchwise heating of aqueous solutions in closed vessels with monitoring of temperatures and pressures. A simple, convenient apparatus and procedure were demonstrated for observing formation of gaseous products and collecting samples for analyses. The test conditions were 250 degree C and 1000 psi max. Any useful reduction of sodium nitrate to sodium hydroxide as the primary product was not found. The nitrate present at pHs 3 or NH 4 NO 3 is easily decomposed, and the effect of nitromethane at these low pHs was confirmed. When acetic acid or formic acid was added, 21 to 56% of the nitrate in sodium nitrate solutions was reduced by methanol or formaldehyde. With hydrazine and acetic acid, 73 % of the nitrate was decomposed to convert NaNO 3 to sodium acetate. With hydrazine and formic acid, 36% of the nitrate was decomposed. If these products are more acceptable for final disposal than sodium nitrate, the reagents are cheap and the conversion conditions would be practical for easy use. Ammonium acetate or formate salts did not significantly reduce nitrate in sodium nitrate solutions

Existence and stability of periodic solutions for a delayed prey-predator model with diffusion effects

Directory of Open Access Journals (Sweden)

Hongwei Liang

2016-01-01

Full Text Available Existence and stability of spatially periodic solutions for a delay prey-predator diffusion system are concerned in this work. We obtain that the system can generate the spatially nonhomogeneous periodic solutions when the diffusive rates are suitably small. This result demonstrates that the diffusion plays an important role on deriving the complex spatiotemporal dynamics. Meanwhile, the stability of the spatially periodic solutions is also studied. Finally, in order to verify our theoretical results, some numerical simulations are also included.

Compensation of Disadvantages in University Examination Procedures

Directory of Open Access Journals (Sweden)

Ulrike Quapp

2016-08-01

Full Text Available Active social participation of disabled people is one of the major tasks of modern society. That also includes access to the academic community by higher education. Universities all over the world work hard to give handicapped students a chance to graduate. In this context, compensation of disadvantages in examination procedures is an important matter. But, also chronic illness may impair the student's examination performance. To ensure equal examination opportunities for all students, responsible university officials must be creative to find individual compensation solutions. The paper analyzes examination regulations at universities in different countries and offers solutions to compensate disabled and chronic ill students' disadvantages. It discusses the necessity of compensation for different types of disability and chronic illness. Finally, an overview of current German case law and solutions for compensation problems are provided.

The readability and suitability of sexual health promotion leaflets.

Science.gov (United States)

Corcoran, Nova; Ahmad, Fatuma

2016-02-01

To investigate the readability and suitability of sexual health promotion leaflets. Application of SMOG, FRY and SAM tests to assess the readability and suitability of a selection of sexual health leaflets. SMOG and FRY scores illustrate an average reading level of grade 9. SAM scores indicate that 59% of leaflets are superior in design and 41% are average in design. Leaflets generally perform well in the categories of content, literacy demand, typography and layout. They perform poorly in use of graphics, learning stimulation/motivation and cultural appropriateness. Sexual health leaflets have a reading level that is too high. Leaflets perform well on the suitability scores indicating they are reasonably suitable. There are a number of areas where sexual health leaflets could improve their design. Numerous practical techniques are suggested for improving the readability and suitability of sexual health leaflets. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Land suitability for waste disposal in metropolitan areas.

Science.gov (United States)

Baiocchi, Valerio; Lelo, Keti; Polettini, Alessandra; Pomi, Raffaella

2014-08-01

Site selection for waste disposal is a complex task that should meet the requirements of communities and stakeholders. In this article, three decision support methods (Boolean logic, index overlay and fuzzy gamma) are used to perform land suitability analysis for landfill siting. The study was carried out in one of the biggest metropolitan regions of Italy, with the objective of locating suitable areas for waste disposal. Physical and socio-economic information criteria for site selection were decided by a multidisciplinary group of experts, according to state-of-the-art guidelines, national legislation and local normative on waste management. The geographic information systems (GIS) based models used in this study are easy to apply but require adequate selection of criteria and weights and a careful evaluation of the results. The methodology is arranged in three steps, reflecting the criteria defined by national legislation on waste management: definition of factors that exclude location of landfills or waste treatment plants; classification of the remaining areas in terms of suitability for landfilling; and evaluation of suitable sites in relation to preferential siting factors (such as the presence of quarries or dismissed plants). The results showed that more than 80% of the provincial territory falls within constraint areas and the remaining territory is suitable for waste disposal for 0.72% or 1.93%, according to the model. The larger and most suitable sites are located in peripheral areas of the metropolitan system. The proposed approach represents a low-cost and expeditious alternative to support the spatial decision-making process. © The Author(s) 2014.

Description of design and operating procedures of small scale pulsed columns for experimental study on extraction process under abnormal conditions

International Nuclear Information System (INIS)

Wakamatsu, Sachio; Sato, Makoto; Kubo, Nobuo; Sakurai, Satoshi; Ami, Norio

1990-09-01

To study transient phenomena in a pulsed column co-decontamination process under abnormal conditions, a pair of small scale pulsed columns (effective extraction section; I.D: 25 mm, H.: 2260 mm) for extraction and scrub were installed in the laboratory. An evaporator of aqueous uranium solution was also equipped to reuse concentrated solution as the feed. This report describes several items to have been carefully treated in design, specification and operating procedure of the apparatuses for the experiments. Also described are the procedures for preparation of the feed solutions and treatments of the solutions after the experiments; back-extraction of uranium, diluent washing, alkaline washing and concentration of uranium solution. (author)

Comparison of infrared coagulation and rubber band ligation, two simple and cost effective office procedures in the treatment of internal haemorrhoids

Directory of Open Access Journals (Sweden)

Surath C Patra

2014-01-01

Conclusion: Rubber Band Ligation was more effective but more painful, while Infrared coagulation was less painful but their efficacy was also lower. Therefore, It is concluded that Infrared coagulation could be considered a suitable alternative office procedure for early stage haemorrhoids as this office procedure can be conveniently repeated in case of recurrence.

Two-dimensional finite element solution for the simultaneous transport of water and solutes through a nonhomogeneous aquifer under transient saturated unsaturated flow conditions

International Nuclear Information System (INIS)

Gureghian, A.B.

1979-01-01

A mathematical model of ground water transport through an aquifer is presented. The solute of interest is a metal tracer or radioactive material which may undergo decay through a sorbing unconfined aquifer. The subject is developed under the following headings: flow equation, solute equation, boundary conditions, finite element formulation, element formulation, solution scheme (flow equation, solute equation), results and discussions, water movement in a ditch drained aquifer under transient state, water and solute movement in a homogeneous and unsaturated soil, transport of 226 Ra in nonhomogeneous aquifer, tailings pond lined, and tailings pond unlined. It is concluded that this mathematical model may have a wide variety of applications. The uranium milling industry may find it useful to evaluate the hydrogeological suitability of their disposal sites. It may prove suited for the design of clay disposal ponds destined to hold hazardous liquids. It may also provide a means of estimating the long-term impact of radionuclides or other pollutants on the quality of ground water. 31 references, 9 figures, 3 tables

Recovery of Tin and Nitric Acid from Spent Solder Stripping Solutions

International Nuclear Information System (INIS)

Ahn, Jae-Woo; Ryu, Seong-Hyung; Kim, Tae-young

2015-01-01

Spent solder-stripping solutions containing tin, copper, iron, and lead in nitric acid solution, are by-products of the manufacture of printed-circuit boards. The recovery of these metals and the nitric acid, for re-use has economic and environmental benefits. In the spent solder-stripping solution, a systematic method to determine a suitable process for recovery of valuable metals and nitric acid was developed. Initially, more than 90% of the tin was successfully recovered as high-purity SnO 2 by thermal precipitation at 80 ℃ for 3 hours. About 94% of the nitric acid was regenerated effectively from the spent solutions by diffusion dialysis, after which there remained copper, iron, and lead in solution. Leakage of tin through the anion-exchange membrane was the lowest (0.026%), whereas Pb-leakage was highest (4.26%). The concentration of the regenerated nitric acid was about 5.1 N.

Positive solutions with changing sign energy to a nonhomogeneous elliptic problem of fourth order

Directory of Open Access Journals (Sweden)

M.Talbi

2011-01-01

Full Text Available In this paper, we study the existence for two positive solutions toa nonhomogeneous elliptic equation of fourth order with a parameter lambda such tha 0 < lambda < lambda^. The first solution has a negative energy while the energy of the second one is positive for 0 < lambda < lambda_0 and negative for lambda_0 < lambda < lambda^. The values lambda_0 and lambda^ are given under variational form and we show that every corresponding critical point is solution of the nonlinear elliptic problem (with a suitable multiplicative term.

On exponential stability and periodic solutions of CNNs with delays

Science.gov (United States)

Cao, Jinde

2000-03-01

In this Letter, the author analyses further problems of global exponential stability and the existence of periodic solutions of cellular neural networks with delays (DCNNs). Some simple and new sufficient conditions are given ensuring global exponential stability and the existence of periodic solutions of DCNNs by applying some new analysis techniques and constructing suitable Lyapunov functionals. These conditions have important leading significance in the design and applications of globally stable DCNNs and periodic oscillatory DCNNs and are weaker than those in the earlier works [Phys. Rev. E 60 (1999) 3244], [J. Comput. Syst. Sci. 59 (1999)].

Numerical solution of quadratic matrix equations for free vibration analysis of structures

Science.gov (United States)

Gupta, K. K.

1975-01-01

This paper is concerned with the efficient and accurate solution of the eigenvalue problem represented by quadratic matrix equations. Such matrix forms are obtained in connection with the free vibration analysis of structures, discretized by finite 'dynamic' elements, resulting in frequency-dependent stiffness and inertia matrices. The paper presents a new numerical solution procedure of the quadratic matrix equations, based on a combined Sturm sequence and inverse iteration technique enabling economical and accurate determination of a few required eigenvalues and associated vectors. An alternative procedure based on a simultaneous iteration procedure is also described when only the first few modes are the usual requirement. The employment of finite dynamic elements in conjunction with the presently developed eigenvalue routines results in a most significant economy in the dynamic analysis of structures.

Fast Time and Space Parallel Algorithms for Solution of Parabolic Partial Differential Equations

Science.gov (United States)

Fijany, Amir

1993-01-01

In this paper, fast time- and Space -Parallel agorithms for solution of linear parabolic PDEs are developed. It is shown that the seemingly strictly serial iterations of the time-stepping procedure for solution of the problem can be completed decoupled.

Hearing aid user guides: suitability for older adults.

Science.gov (United States)

Caposecco, Andrea; Hickson, Louise; Meyer, Carly

2014-02-01

The aim of this study was to analyse the content, design, and readability of printed hearing aid user guides to determine their suitability for older adults, who are the main users of hearing aids. Hearing aid user guides were assessed using four readability formulae and a standardized tool to assess content and design (SAM - Suitability Assessment of Materials). A sample of 36 hearing aid user guides (four user guides from nine different hearing aid manufacturers) were analysed. Sixty nine percent of user guides were rated 'not suitable' and 31% were rated 'adequate' for their suitability. Many scored poorly for scope, vocabulary, aspects of layout and typography, and learning stimulation and motivation. The mean reading grade level for all user guides was grade 9.6 which is too high for older adults. The content, design, and readability of hearing aid user guides are not optimal for older adults and thus may serve as a barrier to successful hearing aid outcomes for this population.

Identifying Technical Procedures in Pulmonary Medicine That Should Be Integrated in a Simulation-Based Curriculum

DEFF Research Database (Denmark)

Nayahangan, Leizl Joy; Clementsen, Paul Frost; Paltved, Charlotte

2016-01-01

of visible lymph node/tumor of the skin, focused ultrasound scanning of the heart, and thoracoscopy. Conclusion: We performed a Delphi study using a needs assessment formula, which identified 11 technical procedures that are highly suitable for simulation-based training. Medical educators can use this list...

Licensing procedure and requirements in the FRG

International Nuclear Information System (INIS)

Brosche, D.

1981-01-01

The investigations of the different dynamic stresses of pressure suppression systems after the Wuergassen incident in 1972 and their theoretical and experimental solutions required an extraordinary effort from all participants of the licensing procedures. As a consequence of these new problems a lot of mathematical models and computer codes had been developed and a lot of experimental work had been performed. Numerous highly qualified scientists and engineers had been involved for a long time in the licensing procedures and innumerable discussions had been necessary. These investigations and discussions had a great influence on the licensing procedures and on the project running. Too pessimistic assumptions and wrong interpretations of experiments led to fictitious problems and a lot of time and money was necessary to overcome these difficulties. Finally at 1977 it could be proved that the construction was able to control stresses so that additional investigations were not necessary. (orig./HP)

Ground state solutions for diffusion system with superlinear nonlinearity

Directory of Open Access Journals (Sweden)

Zhiming Luo

2015-03-01

where $z=(u,v\\colon\\mathbb{R}\\times\\mathbb{R}^{N}\\rightarrow\\mathbb{R}^{2}$, $b\\in C^{1}(\\mathbb{R}\\times\\mathbb{R}^{N}, \\mathbb{R}^{N}$ and $V(x\\in C(\\mathbb{R}^{N},\\mathbb{R}$. Under suitable assumptions on the nonlinearity, we establish the existence of ground state solutions by the generalized Nehari manifold method developed recently by Szulkin and Weth.

Reduced analysis and confirmatory research on co-adaptability theoretical solution to conflicting events in construction engineering projects

Institute of Scientific and Technical Information of China (English)

无

2010-01-01

The co-adaptability theoretical solution to conflicting events in construction engineering projects has three problems. First, the transformation of constraint conditions of theoretical solution is very difficult in practical engineering applications; second, some coefficients are difficult to be determined; third, there are overfull circular arithmetic operations involved in it. To resolve these problems, a new method to reduce the theoretical solution complications is proposed. By analyzing the operating mechanism of theoretical solution model, redundancies in the theoretical solution can be eliminated, and the ISM mapping with the co-adaptability solution can be set up. Based on this approach, a procedure to solve practical conflicting events in construction projects is established by replacing characteristic variables with mathematic variables. The research results show that the procedure can replace the co-adaptability theoretical solution effectively and solve practical conflicting events in construction projects.

Controversy over Issue Preclusion in Russia’s Criminal Procedure: Can Common Law Offer a Solution?

Directory of Open Access Journals (Sweden)

Yury Rovnov

2015-01-01

Full Text Available Even though Russia’s new Code of Criminal Procedure of 2001 had from the very beginning contained the article titled ‘Preclusive Effects,’ it was not until a decision by the Constitutional Court of 2008 that the doctrine of issue preclusion was, in its proper sense, reinstated in Russian criminal law, barring facts definitively established in a civil trial from relitigation in criminal proceedings. Despite heavy criticism that came down on the Constitutional Court for what was seen by law enforcement agents as unwarranted judicial activism, the Russian Parliament soon amended the article in line with the interpretation offered by the Court. This, however, did not end the controversy as critics raised a valid point: an automatic transfer of facts from civil proceedings with a priori more lenient requirements of proof is likely to distort outcomes, harming defendants, the prosecution, and, ultimately, societal interests. This article will turn for apotential solution to common law, which has been able to avoid this problem by clearly distinguishing between different standards of proof applicable in civil v. criminal litigations. It will be shown, using the United States as an example, how courts can effectively use issue preclusion to pursue a number of legitimate objectives, such as consistency of judgments and judicial economy, with due account for the interests of parties in proceedings. At the same time, issue preclusion appears an inappropriate and ineffective means to combat arbitrariness of the judiciary – the end which Russia’s Constitutional Court and law makers arguably had in mind when introducing the doctrine into Russian law.

Low-Temperature Solution Processable Electrodes for Piezoelectric Sensors Applications

Science.gov (United States)

Tuukkanen, Sampo; Julin, Tuomas; Rantanen, Ville; Zakrzewski, Mari; Moilanen, Pasi; Lupo, Donald

2013-05-01

Piezoelectric thin-film sensors are suitable for a wide range of applications from physiological measurements to industrial monitoring systems. The use of flexible materials in combination with high-throughput printing technologies enables cost-effective manufacturing of custom-designed, highly integratable piezoelectric sensors. This type of sensor can, for instance, improve industrial process control or enable the embedding of ubiquitous sensors in our living environment to improve quality of life. Here, we discuss the benefits, challenges and potential applications of piezoelectric thin-film sensors. The piezoelectric sensor elements are fabricated by printing electrodes on both sides of unmetallized poly(vinylidene fluoride) film. We show that materials which are solution processable in low temperatures, biocompatible and environmental friendly are suitable for use as electrode materials in piezoelectric sensors.

Mobility of arsenic and its compounds in soil and soil solution: the effect of soil pretreatment and extraction methods.

Science.gov (United States)

Száková, J; Tlustos, P; Goessler, W; Frková, Z; Najmanová, J

2009-12-30

The effect of soil extraction procedures and/or sample pretreatment (drying, freezing of the soil sample) on the extractability of arsenic and its compounds was tested. In the first part, five extraction procedures were compared with following order of extractable arsenic portions: 2M HNO(3)>0.43 M CH(3)COOH>or=0.05 M EDTA>or=Mehlich III (0.2M CH(3)COOH+0.25 M NH(4)NO(3)+0.013 M HNO(3)+0.015 M NH(4)F+0.001 M EDTA) extraction>water). Additionally, two methods of soil solution sampling were compared, centrifugation of saturated soil and the use of suction cups. The results showed that different sample pretreatments including soil solution sampling could lead to different absolute values of mobile arsenic content in soils. However, the interpretation of the data can lead to similar conclusions as apparent from the comparison of the soil solution sampling methods (r=0.79). For determination of arsenic compounds mild extraction procedures (0.05 M (NH(4))(2)SO(4), 0.01 M CaCl(2), and water) and soil solution sampling using suction cups were compared. Regarding the real soil conditions the extraction of fresh samples and/or in situ collection of soil solution are preferred among the sample pretreatments and/or soil extraction procedures. However, chemical stabilization of the solutions should be allowed and included in the analytical procedures for determination of individual arsenic compounds.

Riccati-parameter solutions of nonlinear second-order ODEs

International Nuclear Information System (INIS)

Reyes, M A; Rosu, H C

2008-01-01

It has been proven by Rosu and Cornejo-Perez (Rosu and Cornejo-Perez 2005 Phys. Rev. E 71 046607, Cornejo-Perez and Rosu 2005 Prog. Theor. Phys. 114 533) that for some nonlinear second-order ODEs it is a very simple task to find one particular solution once the nonlinear equation is factorized with the use of two first-order differential operators. Here, it is shown that an interesting class of parametric solutions is easy to obtain if the proposed factorization has a particular form, which happily turns out to be the case in many problems of physical interest. The method that we exemplify with a few explicitly solved cases consists in using the general solution of the Riccati equation, which contributes with one parameter to this class of parametric solutions. For these nonlinear cases, the Riccati parameter serves as a 'growth' parameter from the trivial null solution up to the particular solution found through the factorization procedure

Stability-Indicating HPLC Method for Simultaneous Determination of Chloramphenicol, Dexamethasone Sodium Phosphate and Tetrahydrozoline Hydrochloride in Ophthalmic Solution.

Science.gov (United States)

AlAani, Hashem; Alnukkary, Yasmin

2016-03-01

A simple stability-indicating RP-HPLC assay method was developed and validated for quantitative determination of Chloramphenicol, Dexamethasone Sodium Phosphate and Tetrahydrozoline Hydrochloride in ophthalmic solution in the presence of 2-amino-1-(4-nitrophenyl)propane-1,3-diol, a degradation product of Chloramphenicol, and Dexamethasone, a degradation product of Dexamethasone Sodium Phosphate. Effective chromatographic separation was achieved using C18 column (250 mm, 4.6 mm i.d., 5 μm) with isocratic mobile phase consisting of acetonitrile - phosphate buffer (pH 4.0; 0.05 M) (30:70, v/v) at a flow rate of 1 mL/minute. The column temperature was maintained at 40°C and the detection wavelength was 230 nm. The proposed HPLC procedure was statistically validated according to the ICH guideline, and was proved to be stability-indicating by resolution of the APIs from their forced degradation products. The developed method is suitable for the routine analysis as well as stability studies.

The Kjeldahl method as a primary reference procedure for total protein in certified reference materials used in clinical chemistry. II. Selection of direct Kjeldahl analysis and its preliminary performance parameters.

Science.gov (United States)

Vinklárková, Bára; Chromý, Vratislav; Šprongl, Luděk; Bittová, Miroslava; Rikanová, Milena; Ohnútková, Ivana; Žaludová, Lenka

2015-01-01

To select a Kjeldahl procedure suitable for the determination of total protein in reference materials used in laboratory medicine, we reviewed in our previous article Kjeldahl methods adopted by clinical chemistry and found an indirect two-step analysis by total Kjeldahl nitrogen corrected for its nonprotein nitrogen and a direct analysis made on isolated protein precipitates. In this article, we compare both procedures on various reference materials. An indirect Kjeldahl method gave falsely lower results than a direct analysis. Preliminary performance parameters qualify the direct Kjeldahl analysis as a suitable primary reference procedure for the certification of total protein in reference laboratories.

Site selection procedure for high level radioactive waste disposal in Bulgaria

International Nuclear Information System (INIS)

Evstatiev, D.; Vachev, B.

1993-01-01

A combined site selection approach is implemented. Bulgaria's territory has been classified in three categories, presented on a 1:500000 scale map. The number of suitable sites has been reduced to 20 using the method of successive screening. The formulated site selection problem is a typical discrete multi-criteria decision making problem under uncertainty. A 5-level procedure using Expert Choice Rating and relative models is created. It is a part of a common procedure for evaluation and choice of variants for high level radwaste disposal construction. On this basis 7-8 more preferable sites are demonstrated. A new knowledge and information about the relative importance of the criteria and their subsets, about the level of criteria uncertainty and the reliability are gained. It is very useful for planning and managing of the next final stages of the site selection procedure. 7 figs., 8 refs., 4 suppls. (author)

A Computerized Procedure linked to Virtual Equipment

International Nuclear Information System (INIS)

Jung, Yeon Sub; Song, Tae Young

2011-01-01

Digital, information, and communication technologies have change human's behavior. This is because human has limitation to memorize and process information. Human has to access other information and real time information for important decisions. Those technologies are playing important roles. Nuclear power plants cannot be exception. Many accidents in nuclear power plants result from absent or incorrect information. The information for nuclear personnel is context sensitive. They don't have enough time to verify the context sensitive information. Therefore they skip the information, as resulting in incident. Nuclear personnel are usually carrying static paper procedures during local task performance. The procedure guides them steps to follow. There is, however, no dynamic and context sensitive information in the paper. The effect of the work is evaluated once while getting permission of the work. Afterward they are not informed. The static paper is generally simplified, so that it does not show detail of equipment being manipulated. Particularly novice workers feel difficult to understand the procedure due to lack of detail. Pictures of equipment inserted in the procedure are not enough for comprehension. A computerized procedure linked with virtual equipment is one of the best solutions to increase the detail of procedure. Virtual equipment, however, has still limitation not to provide real time information, because the virtual equipment is not synchronized with real plants

Considering the normative, systemic and procedural dimensions in indicator-based sustainability assessments in agriculture

International Nuclear Information System (INIS)

Binder, Claudia R.; Feola, Giuseppe; Steinberger, Julia K.

2010-01-01

This paper develops a framework for evaluating sustainability assessment methods by separately analyzing their normative, systemic and procedural dimensions as suggested by Wiek and Binder [Wiek, A, Binder, C. Solution spaces for decision-making - a sustainability assessment tool for city-regions. Environ Impact Asses Rev 2005, 25: 589-608.]. The framework is then used to characterize indicator-based sustainability assessment methods in agriculture. For a long time, sustainability assessment in agriculture has focused mostly on environmental and technical issues, thus neglecting the economic and, above all, the social aspects of sustainability, the multi-functionality of agriculture and the applicability of the results. In response to these shortcomings, several integrative sustainability assessment methods have been developed for the agricultural sector. This paper reviews seven of these that represent the diversity of tools developed in this area. The reviewed assessment methods can be categorized into three types: (i) top-down farm assessment methods; (ii) top-down regional assessment methods with some stakeholder participation; (iii) bottom-up, integrated participatory or transdisciplinary methods with stakeholder participation throughout the process. The results readily show the trade-offs encountered when selecting an assessment method. A clear, standardized, top-down procedure allows for potentially benchmarking and comparing results across regions and sites. However, this comes at the cost of system specificity. As the top-down methods often have low stakeholder involvement, the application and implementation of the results might be difficult. Our analysis suggests that to include the aspects mentioned above in agricultural sustainability assessment, the bottom-up, integrated participatory or transdisciplinary methods are the most suitable ones.

New robust statistical procedures for the polytomous logistic regression models.

Science.gov (United States)

Castilla, Elena; Ghosh, Abhik; Martin, Nirian; Pardo, Leandro

2018-05-17

This article derives a new family of estimators, namely the minimum density power divergence estimators, as a robust generalization of the maximum likelihood estimator for the polytomous logistic regression model. Based on these estimators, a family of Wald-type test statistics for linear hypotheses is introduced. Robustness properties of both the proposed estimators and the test statistics are theoretically studied through the classical influence function analysis. Appropriate real life examples are presented to justify the requirement of suitable robust statistical procedures in place of the likelihood based inference for the polytomous logistic regression model. The validity of the theoretical results established in the article are further confirmed empirically through suitable simulation studies. Finally, an approach for the data-driven selection of the robustness tuning parameter is proposed with empirical justifications. © 2018, The International Biometric Society.

A procedure for the radioimmunochemical determination of antigens with different structures

International Nuclear Information System (INIS)

Galoci, J.; Machan, V.

1990-01-01

To a solution of a specific antibody, its antigen labelled with iodine 125, and of the unknown sample is added animal (e.g., goat) antibody against rabbit immunoglobulin immobilized on modified microcrystalline cellulose; always the same quantities are applied always for the same time. After incubation for 1 hr at 20 degC, the immunochemical complex formed is centrifuged and its radioactivity is measured, and the amount of the antigen in sample is determined by comparison with standards. The procedure is applicable to antigens with any structure. Assets of the separating system include a very good stability in solution, a low value of nonspecific bonding and a low sedimentation velocity of the particles used. The procedure is well suited to the quantitation of antigens present in very low concentrations in blood serum, urine, milk, and extracts from tissues or animal feed. In a modification of the procedure, the animal antibody against rabbit immunoglobulin is immobilized on the surface of modified cellulose particles 5 to 15 μm in size exhibiting a very low sedimentation velocity, activated with 1,1-carbonyldiimidazole. (M.D.)

Selection of suitable sites for NPP in Slovenia (stage 3)

International Nuclear Information System (INIS)

Grgic, M.; Fabjan, L.; Premru, U.

1977-01-01

Selection of suitable sites for nuclear power plants in Slovenia is considered. This includes the studies of available data on regional and local characteristics specified in general site suitability criteria for NPP. The most suitable selected sites will be included into land use urbanistic planning of Slovenia

Analytical solution for the transport equation for neutral particles in cylindrical and Cartesian geometry

International Nuclear Information System (INIS)

Goncalves, Glenio Aguiar

2003-01-01

In this work, we are reported analytical solutions for the transport equation for neutral particles in cylindrical and cartesian geometry. For the cylindrical geometry, it is applied the Hankel transform of order zero in the S N approximation of the one-dimensional cylindrical transport equation, assuming azimuthal symmetry and isotropic scattering. This procedure is coined HTSN method. The anisotropic problem is handled using the decomposition method, generating a recursive approach, which the HTSN solution is used as initial condition. For cartesian geometry, the one and two dimensional transport equation is derived in the angular variable as many time as the degree of the anisotropic scattering. This procedure leads to set of integro-differential plus one differential equation that can be really solved by the variable separation method. Following this procedure, it was possible to come out with the Case solution for the one-dimensional problem. Numerical simulations are reported for the cylindrical transport problem both isotropic and anisotropic case of quadratic degree. (author)

Evaluation of habitat suitability models for forest passerines using demographic data

Science.gov (United States)

Chadwick D. Rittenhouse; Frank R., III Thompson; William D. Dijak; Joshua J. Millspaugh; Richard L. Clawson

2010-01-01

Habitat suitability is often used as a surrogate for demographic responses (i.e., abundance, survival, fecundity, or population viability) in the application of habitat suitability index (HSI) models. Whether habitat suitability actually relates to demographics, however, has rarely been evaluated. We validated HSI models of breeding habitat suitability for wood thrush...

Biolasol: novel perfusion and preservation solution for kidneys.

Science.gov (United States)

Cierpka, L; Ryszka, F; Dolińska, B; Smorąg, Z; Słomski, R; Wiaderkiewicz, R; Caban, A; Budziński, G; Oczkowicz, G; Wieczorek, J

2014-10-01

Biolasol solution (Pharmaceutical Research and Production Plant "Biochefa," Sosnowiec, Poland) is a novel extracellular perfusion and ex vivo hypothermic kidney preservation solution. It ensures maintenance of homeostasis, reduces tissue edema, has low viscosity, and allows the graft to preserve structural and functional integrity. It minimizes ischemia-reperfusion damage. Perfundates from control and transplanted kidneys flushed with Biolasol or ViaSpan solutions (Arkas, Warszawa, Poland) were analyzed. Parameters of serum and urine collected from 12 pigs after auto-transplantation were also analyzed. Renal medulla was investigated for structural alterations by analyzing hematoxylin and eosin-stained slides. The mean survival time of pigs after the auto-transplantation procedure was the measure for the novel Biolasol solution effectiveness. We observed a statistically significant decrease in marker enzyme levels alanine transaminase, aspartate transaminase, lactic dehydrogenase, and ions (Na and K) in pigs with grafts flushed with Biolasol. Histopathologic examination revealed that the renal cortex structure was not damaged after the use of Biolasol solution. Biolasol solution protects kidneys against ischemia damage and does not differ significantly from the "golden standard" ViaSpan solution.

Elk habitat suitability map for North Carolina

Science.gov (United States)

Williams, Steven G.; Cobb, David T.; Collazo, Jaime A.

2015-01-01

Although eastern elk (Cervus elaphus canadensis) were extirpated from the eastern United States in the 19th century, they were successfully reintroduced in the North Carolina portion of the Great Smoky Mountains National Park in the early 2000s. The North Carolina Wildlife Resources Commission (NCWRC) is evaluating the prospect of reintroducing the species in other locations in the state to augment recreational opportunities. As a first step in the process, we created a state-wide elk habitat suitability map. We used medium-scale data sets and a two-component approach to iden- tify areas of high biological value for elk and exclude from consideration areas where elk-human conflicts were more likely. Habitats in the state were categorized as 66% unsuitable, 16.7% low, 17% medium, and <1% high suitability for elk. The coastal plain and Piedmont contained the most suitable habitat, but prospective reintroduction sites were largely excluded from consideration due to extensive agricultural activities and pervasiveness of secondary roads. We ranked 31 areas (≥ 500 km2) based on their suitability for reintroduction. The central region of the state contained the top five ranked areas. The Blue Ridge Mountains, where the extant population of elk occurs, was ranked 21st. Our work provides a benchmark for decision makers to evaluate potential consequences and trade-offs associated with the selection of prospective elk reintroduction sites.

Explicit Solutions for One-Dimensional Mean-Field Games

KAUST Repository

Prazeres, Mariana

2017-04-05

In this thesis, we consider stationary one-dimensional mean-field games (MFGs) with or without congestion. Our aim is to understand the qualitative features of these games through the analysis of explicit solutions. We are particularly interested in MFGs with a nonmonotonic behavior, which corresponds to situations where agents tend to aggregate. First, we derive the MFG equations from control theory. Then, we compute explicit solutions using the current formulation and examine their behavior. Finally, we represent the solutions and analyze the results. This thesis main contributions are the following: First, we develop the current method to solve MFG explicitly. Second, we analyze in detail non-monotonic MFGs and discover new phenomena: non-uniqueness, discontinuous solutions, empty regions and unhappiness traps. Finally, we address several regularization procedures and examine the stability of MFGs.

[Ecology suitability study of Chinese materia medica Gentianae Macrophyllae Radix].

Science.gov (United States)

Lu, You-Yuan; Yang, Yan-Mei; Ma, Xiao-Hui; Zhang, Xiao-Bo; Zhu, Shou-Dong; Jin, Ling

2016-09-01

This paper is aimed to predict ecology suitability distribution of Gentianae Macrophyllae Radix and search the main ecological factors affecting the suitability distribution. The 313 distribution information about G. macrophylla, 186 distribution information about G. straminea, 343 distribution information about G. dauricaand 131 distribution information about G. crasicaulis were collected though investigation and network sharing platform data . The ecology suitable distribution factors for production Gentianae Macrophyllae Radix was analyzed respectively by the software of ArcGIS and MaxEnt with 55 environmental factors. The result of MaxEnt prediction was very well (AUC was above 0.9). The results of predominant factors analysis showed that precipitation and altitude were all the major factors impacting the ecology suitable of Getiana Macrophylla Radix production. G. macrophylla ecology suitable region was mainly concentrated in south of Gansu, Shanxi, central of Shaanxi and east of Qinghai provinces. G. straminea ecology suitable region was mainly concentrated in southwest of Gansu, east of Qinghai, north and northwest of Sichuan, east of Xizang province. G. daurica ecology suitable region was mainly concentrated in south and southwest of Gansu, east of Qinghai, Shanxi and north of Shaanxi province. G. crasicaulis ecology suitable region was mainly concentrated in Sichuan and north of Yunnan, east of Xizang, south of Gansu and east of Qinghai province. The ecological suitability distribution result of Gentianae Macrophyllae Radix was consistent with each species actual distribution. The study could provide reference for the collection and protection of wild resources, meanwhile, provide the basis for the selection of cultivation area of Gentiana Macrophylla Radix. Copyright© by the Chinese Pharmaceutical Association.

Test amnioinfusion to determine suitability for serial therapeutic amnioinfusion in midtrimester premature rupture of membranes.

Science.gov (United States)

Tan, L-K; Kumar, S; Jolly, M; Gleeson, C; Johnson, P; Fisk, N M

2003-01-01

To evaluate whether a test amnioinfusion procedure is useful in selecting cases of midtrimester preterm premature rupture of membranes (PPROM) which may benefit from serial amnioinfusions if the initial fluid is retained. The Centre for Fetal Care database between 1992 and 2000 was reviewed for women with PPROM amnioinfusion. Amniotic fluid index (AFI) was assessed before and after a test amnioinfusion procedure. Those who retained fluid > or =48 h underwent serial AFI assessment with a view to serial amnioinfusion when oligohydramnios recurred. Eighty-five amnioinfusion procedures were performed in 60 women with oligohydramnios. Nineteen of these women presented with confirmed PPROM at a median gestation of 19 (range 15-22) weeks and severe olighohydramnios (median AFI 1, range 0-3 cm), in whom 20 test amnioinfusions were carried out. Two amnioinfusions were abandoned during the procedure because of fetal bradycardia and both mothers opted for termination of pregnancy. Only 4 women retained fluid during the test amnioinfusion, 1 of whom miscarried at 19 weeks before serial amnioinfusion could be started. The remaining 3 underwent a median of 4 (range 1-6) serial amnioinfusion procedures; none had evidence of pulmonary hypoplasia. Thirteen (68%) leaked fluid within 48 h; within this group there was 1 subsequent miscarriage and 9 pregnancy terminations. The remaining 3 pregnancies resulted in livebirths 2 of which had pulmonary hypoplasia with 1 early neonatal death. Overall survival was poor (4/19), largely attributed to the high incidence of terminations in the presence of persistent severe oligohydramnios. In continuing pregnancies reaching viability survival was 67% (4 of 6). Three quarters of women with mid-trimester PPROM lose fluid at test amnioinfusion and therefore would not be suitable candidates for serial amnioinfusion. However, if infused fluid is retained, this allows subsequent serial amnioinfusion and prolongation of pregnancy in about 75%, with an

Analytical solutions to the electromagnetic field in a cylindrical shell excited by external axial current

International Nuclear Information System (INIS)

Jing, Wu; Chun-Yan, Xiao

2010-01-01

The solutions to the electromagnetic field excited by a long axial current outside a conductive and magnetic cylindrical shell of finite length are studied in this paper. The more accurate analytical solutions are obtained by solving the proper boundary value problems by the separation variable method. Then the solutions are simplified according to asymptotic formulas of Bessel functions. Compared with the accurate solutions, the simplified solutions do not contain the Bessel functions and the inverse operation of the singular matrix, and can be calculated out fast by computers. The simplified solutions are more suitable for the cylindrical shell of high permeability and conductivity excited by a high frequency source. Both of the numerical results and the physical experimental results validate the simplified solutions obtained. (classical areas of phenomenology)

Surgical solutions for the complications of the Vaseline self-injection of the penis.

Science.gov (United States)

Bajory, Zoltán; Mohos, Gábor; Rosecker, Agnes; Bordás, Noémi; Pajor, László

2013-04-01

Penile girth enhancement by the injection of Vaseline is an existing practice. Many cases develop severe complications that need surgery. To report on the reconstructive surgical solutions of the complications of Vaseline self-injection and the outcomes. To develop a modification of a one-step reconstruction method involving the use of pedicled scrotal flaps. The complications and their surgical solutions were classified as regards severity and difficulty. The outcomes were observed and a newly introduced one-step surgical method was investigated. Seventy-eight consecutive patients (87.2% of them with a history of imprisonment) were divided into three groups. In group A, aesthetic penile defects or phimosis caused by the Vaseline necessitated circumcision or local excision. In group B, the whole penile skin was involved, and total skin removal and two- or (a newly modified) one-step reconstructive surgery were performed. In group C, both the whole penile skin and the scrotum were involved: complete skin removal and skin grafting or skin pedicled flap transplantation were carried out. In five cases in group B, postoperative skin necrosis made a second operation necessary. There was one intraoperative urethral injury, where a urethral fistula developed and a second urethral reconstruction was performed. There was no major complication with the newly developed one-stage pedicled flap procedure. At the end of the therapy, all the cases were healed. All of the patients reported successful sexual intercourse after the operations and 91% were satisfied with the result. The complications depend mainly on the amount of Vaseline injected, the hygienic circumstances, and the personal tolerability. In the worst cases, only radical skin removal and skin transplantation can solve the problem. The newly developed one-step arterial branch-preserving scrotal skin flap reconstruction appears to be a suitable and cost-effective solution for these patients. © 2013 International

Numerical model for the solution of two-dimensional natural convection problems in arbitrary cavities

International Nuclear Information System (INIS)

Milioli, F.E.

1985-01-01

In this research work a numerical model for the solution of two-dimensional natural convection problems in arbitrary cavities of a Boussinesq fluid is presented. The conservation equations are written in a general curvilinear coordinate system which matches the irregular boundaries of the domain. The nonorthogonal system is generated by a suitable system of elliptic equations. The momentum and continuity equations are transformed from the Cartesian system to the general curvilinear system keeping the Cartesian velocity components as the dependent variables in the transformed domain. Finite difference equations are obtained for the contravariant velocity components in the transformed domain. The numerical calculations are performed in a fixed rectangular domain and both the Cartesian and the contravariant velocity components take part in the solutiomn procedure. The dependent variables are arranged on the grid in a staggered manner. The numerical model is tested by solving the driven flow in a square cavity with a moving side using a nonorthogoanl grid. The natural convenction in a square cavity, using an orthogonal and a nonorthogonal grid, is also solved for the model test. Also, the solution for the buoyancy flow between a square cylinder placed inside a circular cylinder is presented. The results of the test problems are compared with those available in the specialized literature. Finally, in order to show the generality of the model, the natural convection problem inside a very irregular cavity is presented. (Author) [pt

Analytical solutions to orthotropic variable thickness disk problems

Directory of Open Access Journals (Sweden)

Ahmet N. ERASLAN

2016-02-01

Full Text Available An analytical model is developed to estimate the mechanical response of nonisothermal, orthotropic, variable thickness disks under a variety of boundary conditions. Combining basic mechanical equations of disk geometry with the equations of orthotropic material, the elastic equation of the disk is obtained. This equation is transformed into a standard hypergeometric differential equation by means of a suitable transformation. An analytical solution is then obtained in terms of hypergeometric functions. The boundary conditions used to complete the solutions simulate rotating annular disks with two free surfaces, stationary annular disks with pressurized inner and free outer surfaces, and free inner and pressurized outer surfaces. The results of the solutions to each of these cases are presented in graphical forms. It is observed that, for the three cases investigated the elastic orthotropy parameter turns out to be an important parameter affecting the elastic behaviorKeywords: Orthotropic disk, Variable thickness, Thermoelasticity, Hypergeometric equation

Habitat Evaluation Procedures (HEP) Report : Priest River, 2004-2005 Technical Report.

Energy Technology Data Exchange (ETDEWEB)

Entz, Ray

2005-02-01

On July 6, 2004, the Habitat Evaluation Procedure (HEP) was used to determine baseline habitat suitability on the Priest River property, an acquisition completed by the Kalispel Tribe of Indians in 2001. Evaluation species and appropriate models include bald eagle, black-capped chickadee, Canada goose, mallard, yellow warbler, and white-tailed deer. Habitat Suitability Index (HSI) values were visually estimated and agreed upon by all HEP team members. The Priest River Project provides a total of 105.41 Habitat Units (HUs) for the species evaluated. Conifer forest habitat provides 26.95 HUs for bald eagle, black-capped chickadee, and white-tailed deer. Grassland habitat provides 23.78 HUs for Canada goose and mallard. Scmb-shrub vegetation provides 54.68 HUs for mallard, yellow warbler, and white-tailed deer.

Thorium determination by x-ray fluorescence spectrometry in simulated thorex process solutions

International Nuclear Information System (INIS)

Yamaura, M.; Matsuda, H.T.

1991-11-01

The X-ray fluorescence method for thorium determination in aqueous and organic (TBP/n-dodecane) solutions is described. The thin film technique for sample preparation and a suitable internal standard had been used. The best conditions for Thorium determination had been established studying some parameters as analytical line, internal standard, filter paper, paper geometry, sample volume and measurement conditions. With the established conditions, thorium was concentration range of to 200 g Th/L and in organic solutions (2-63g Th/L) with 1,5% of precision. The accuracy of the proposed method was 3% in aqueous and organic phases. The detection limit was 1,2μg thorium for aqueous solutions and 1,4μg for organic solutions. Uranium, fission products, corrosion products and Thorex reagent components were studied as interfering elements in the thorium analysis. The matrix effect was also studied using the Thorex process simulated solutions. Finally, the method was applied to thorium determination in irradiated thorium solutions with satisfactory results. (author)

Tsunami shelter in Padang city: Location suitability and management issue

Science.gov (United States)

Rita, Eva; Permata, Robby; Yonne, Hilma; Carlo, Nasfryzal

2017-11-01

The building of Temporary Evacuation Sites (TES/shelter) is an effort to minimize the vulnerability of the population who live in coastal city areas with high risk of tsunami. Padang city in Indonesia, one of the cities with high risk of tsunami, has built shelter in North Ulak Karang Village, North Padang Sub-district. The problems are the location of shelter does not meet the standard of population number, how to manage the shelter in normal condition (without disaster), and who will be responsible for the management of the shelter. The aim of the study is to learn the suitability of shelter location and the management of the shelter in normal condition as well as the expectation of the people who live near the shelter location. This research uses evaluative-descriptive method with the collection of secondary and primary data through structured interviews with 200 respondents in the area of shelter building. The result shows that the furthest location of the shelter is located at RW 03 with a distance of 1.3 kms which takes 12.15-24.30 minutes. It shows that the shelter location in Padang meets the requirement of FEMA P646. At normal condition, shelter can be used for sport and educational activities, as a center for socialisation and simulation of disaster and other activities. The management of the shelter is done together by government and stakeholders. The proposed management is by forming a team (organization) which involves Disaster Alert groups (KSB) and by making the Standard Operational Procedures (SOP) for their implementation. People expect that the number of shelter is added and the building of the shelter is based on the suitability of location, number of population and availability of land.

Fingertip replantation using the subdermal pocket procedure.

Science.gov (United States)

Lin, Tsan-Shiun; Jeng, Seng-Feng; Chiang, Yuan-Cheng

2004-01-01

of follow-up monitoring. Compared with other methods, the subdermal pocket procedure has the advantages of exact subdermal/subdermal contact, a shorter pocketing period, and more feasible observation. The method can offer an alternative salvage procedure for fingertip amputations with no suitable vessels available for microsurgical replantation.

Evaluation of the suitability of the WIPP site

International Nuclear Information System (INIS)

Neill, R.H.; Channell, J.K.; Chaturvedi, L.; Little, M.S.; Rehfeldt, K.; Spiegler, P.

1983-05-01

Determination of the suitability of the site for WIPP is only the first major phase in the evaluation of the radiological impact of the repository on the public health and safety. The Environmental Evaluation Group (EEG) will continue to independently review the design of the facility, the operational procedures, the criteria for packaging and shipment of the waste, the plans, procedures and results of the WIPP experiments, emergency preparedness, adherence to EPA and pertinent NRC regulations, and other important features of the project. EEG has concluded from existing evidence that the Los Medanos site for the WIPP project has been characterized in sufficient detail to warrant confidence in the validation of the site for the permanent emplacement of approximately 6 million cubic feet of defense transuranic waste. This conclusion is based on the assumption that the maximum surface dose rate for the unshielded remote-handled transuranic waste canisters will be 100 rem/hr with a maximum radionuclide concentration of 23 Ci/liter. The Site and Preliminary Design Validation program, through the drilling of two shafts to the selected repository level at 2160 ft below the surface and excavation of about 9000 ft of tunnels, has confirmed the interpretations made about the subsurface geological conditions at the site. For an assessment of the potential radiation effects of the nuclear waste repository on the public health and safety, it is necessary to understand the regional geological and hydrological setting. Much work has been done to understand these conditions and to address several specific issues which have arisen as a result of such studies. However, it is almost inevitable that some questions remain unanswered at a given time in the decision-making process. EEG has identified work which still needs to be done at the Los Medanos site in order to improve confidence in the worst case scenario models of possible breaches of the repository

Genetic risk from diagnostic X-ray procedures

International Nuclear Information System (INIS)

Stephan, G.

1980-01-01

This essay introduces epidemiologic studies concerned with the question whether diagnostic X-ray procedures might be the cause of an increased genetic risk. All studies have selected Down's syndrome (mongolism) as genetic indicator. They indiscriminately present the opinion of the respective author. Approximately one half of the studies conclude that radiation exposure will not influence the spontaneous incidence of Down's syndrome in diagnostics, the other half finds a positive relationship between frequent radiation exposure and the incidence of the syndrome. For various reasons, explained in detail, the results of the studies under discussion are suitable for forming hypotheses, but should not be viewed as providing evidence. (orig.) [de

Computer managed emergency operating procedures

International Nuclear Information System (INIS)

Salamun, I.; Mavko, B.; Stritar, A.

1994-01-01

New computer technology is a very effective tool for developing a new design of nuclear power plant control room. It allows designer possibility to create a tool for managing with large database of power plant parameters and displaying them in different graphic forms and possibility of automated execution of well known task. The structure of Emergency Operating Procedures (EOP) is very suitable for programming and for creating expert system. The Computerized Emergency Operating Procedures (CEOP) described in this paper can be considered as an upgrading of standard EOP approach. EmDiSY (Emergency Display System - computer code name for CEOP) main purpose is to supply the operator with necessary information, to document all operator actions and to execute well known tasks. It is a function oriented CEOP that gives operator guidance on how to verify the critical safety functions and how to restore and maintain these functions where they are degraded. All knowledge is coded and stored in database files. The knowledge base consists from stepping order for verifying plant parameters, desired values of parameters, conditions for comparison and links between procedures and actions. Graphical shell allows users to read database, to follow instruction and to find out correct task. The desired information is concentrated in one screen and allows users to focus on a task. User is supported in two ways: desired parameter values are displayed on the process picture and automated monitoring critical safety function status trees are all time in progress and available to the user. (author). 4 refs, 4 figs

Solid waste dumping site suitability analysis using geographic ...

African Journals Online (AJOL)

Solid waste dumping is a serious problem in the urban areas because most solid wastes are not dumped in the suitable areas. Bahir Dar Town has the problem of solid waste dumping site identification. The main objective of this study was to select potential areas for suitable solid waste dumping sites for Bahir Dar Town, ...

Procedure for the separation of cerium from rare earth phosphate mixtures

International Nuclear Information System (INIS)

Richter, H.; Grauss, H.; Schmitt, A.; Schade, H.; Lindeholz, M.; Lorenz, E.; Weickart, J.

1986-01-01

The invention is concerned with a procedure for the separation of cerium from rare earth concentrates originating from the partial neutralization of nitric crude phosphate decomposition solutions without preceding elimination of impurities from the raw material. The rare earth phosphates are treated with an excess of concentrated nitric acid through which the Ce 3+ , contained in the solution, is oxidized to Ce 4+ and precipitated as cerium(IV) phosphate by neutralization with alkalis

Some remarks on hydrogen release from nitric acid solutions

International Nuclear Information System (INIS)

Specht, S.

1980-01-01

After a survey of the literature on generalisable statements on β, γ-radiolysis of water and salty solutions, an attempt is made to summarize and evaluate existing measurements in connection with the formation of H 2 in nitrous fission product solutions (or corresponding simulates). It is seen that laboratory experiments with such fission products show rather uniform and plausible G(H 2 )-values in the region -3 . It is also seen, however, that G(H 2 )-values and steady H 2 -release rates are not suitable to describe technical systems (HAW stores). Either H 2 is carried away by purge air or it is, in a non-operating system, consumed again in situ, obviously by back reactions. (orig.) [de

The suitability of EDXRF for compositional classification of archaeological pottery

International Nuclear Information System (INIS)

Padilla Alvarez, Roman

2007-01-01

Many investigations have been carried out trying to enlarge the information that can be gathered through the chemical analysis of archaeological findings. Chemical composition data sets, properly interpreted with multivariate analysis techniques, have been used extensively to supplement investigations involving provenance studies or more complex socio-economic aspects of the past communities. Correct inferences from the gathered compositional data are only possible if well documented background information about the studied samples is available, such as a correct interpretation of the archaeological contexts, knowledge about the nature of the used raw materials or procurement sources (geology of the territories), among others. The combined use of Instrumental Neutron Activation Analysis (INAA) and Scanning Electron Microscopy X-ray analysis (SEM-EDX) has been widely applied to the classification of archaeological pottery. However the need to remove at least a minimal part (invasion) of the sample and the time delay required for radioisotope decay and the high costs involved in INAA often restrict its use. Energy Dispersive x-ray Fluorescence spectrometry (EDXRF) is advantageous to perform a completely non-destructive analysis in a relatively fast way, but several problems have restricted its wider use in the past. The highly matrix-dependent attenuation of x-rays in the analysed sample hampers the use of the standard-less quantification procedures as an alternative when suitable certified reference materials are not at hand, and the relatively limited instrumental sensitivity of the conventional spectrometers has not allowed the determination of some trace elements that are relevant for compositional differentiation and provided a comparatively higher uncertainties. This contribution presents the results of several investigations aimed to achieving classification of archaeological pottery using reliable quantitative EDXRF procedures. The main factors affecting the

Potentiometric titration of free acid in uranium solutions

International Nuclear Information System (INIS)

Suh, M. Y.; Kim, W. H.; Kim, J. S.; Sohn, S. C.; Eom, T. Y.; Lee, C. H.; Jeon, Y. S.; Han, S. H.

1998-02-01

Hydrolysis properties of metal cations and fundamental principles of the potentiometric titration of free acid in aqueous solutions containing metal cations were described. The published papers and reports for the alkalimetric and acidimetric titration of free acid were surveyed, and the applicability of these titration methods to the uranium and/or plutonium solutions were discussed. This technical report also includes the various results obtained from the authors' researches to establish the alkalimetric and acidimetric titration methods for the determination of free acid in nitric acid solutions containing uranium and/or oxalic acid, and aluminum. The procedure manuals used in chemical processes and the newly prepared manuals based on the authors' researches are appended. (author). 26 refs., 54 figs

Potentiometric titration of free acid in uranium solutions

Energy Technology Data Exchange (ETDEWEB)

Suh, M. Y.; Kim, W. H.; Kim, J. S.; Sohn, S. C.; Eom, T. Y.; Lee, C. H.; Jeon, Y. S.; Han, S. H.

1998-02-01

Hydrolysis properties of metal cations and fundamental principles of the potentiometric titration of free acid in aqueous solutions containing metal cations were described. The published papers and reports for the alkalimetric and acidimetric titration of free acid were surveyed, and the applicability of these titration methods to the uranium and/or plutonium solutions were discussed. This technical report also includes the various results obtained from the authors` researches to establish the alkalimetric and acidimetric titration methods for the determination of free acid in nitric acid solutions containing uranium and/or oxalic acid, and aluminum. The procedure manuals used in chemical processes and the newly prepared manuals based on the authors` researches are appended. (author). 26 refs., 54 figs.

Direct methods of solution for problems in mechanics from invariance principles

International Nuclear Information System (INIS)

Rajan, M.

1986-01-01

Direct solutions to problems in mechanics are developed from variational statements derived from the principle of invariance of the action integral under a one-parameter family of infinitesimal transformations. Exact, direct solution procedures for linear systems are developed by a careful choice of the arbitrary functions used to generate the infinitesimal transformations. It is demonstrated that the well-known methods for the solution of differential equations can be directly adapted to the required variational statements. Examples in particle and continuum mechanics are presented

Thermodynamic behavior of erythritol in aqueous solutions and in gelatine gels and its quantification

International Nuclear Information System (INIS)

Tyapkova, Oxana; Bader-Mittermaier, Stephanie; Schweiggert-Weisz, Ute

2013-01-01

Highlights: • Differential scanning calorimetry as a method to determine erythritol crystallization. • Determination of crystallization using solution enthalpy. • Erythritol crystallization influenced by area of air–water-interfaces. • DSC method is applicable for both aqueous solutions and gels. • Adaption of DSC method to other, more complex food matrices is possible. - Abstract: As crystallization of erythritol can cause a sandy mouth-feel in sugar-free products, strategies to avoid crystallization or adaption of food formulation should be elucidated. However, until now erythritol crystallization was only quantified in aqueous solutions, but not in model food systems. Differential scanning calorimetry (DSC) is a simple method for the quantification of phase transition in various systems. However, no methods for the quantification of crystallization from aqueous systems based on DSC have been published until now. In the present study DSC was found to be suitable for the quantification of crystallization using supersaturated aqueous solutions of erythritol and erythritol containing gelatine gels for the first time. The developed method was validated by comparing the crystallization values determined by gravimetric measurement of erythritol crystals and the values obtained by DSC. No significant differences (p < 0.05) have been obtained between the results of the two methods if an appropriate design of measurements was applied. Additionally, the method was adapted to gelatine gels to elucidate the transferability to model food systems. Hence, the method is suitable for quantification of the amount of erythritol crystals present in aqueous solutions and gels, respectively

Determining procedures for simulation-based training in radiology: a nationwide needs assessment.

Science.gov (United States)

Nayahangan, Leizl Joy; Nielsen, Kristina Rue; Albrecht-Beste, Elisabeth; Bachmann Nielsen, Michael; Paltved, Charlotte; Lindorff-Larsen, Karen Gilboe; Nielsen, Bjørn Ulrik; Konge, Lars

2018-01-09

New training modalities such as simulation are widely accepted in radiology; however, development of effective simulation-based training programs is challenging. They are often unstructured and based on convenience or coincidence. The study objective was to perform a nationwide needs assessment to identify and prioritize technical procedures that should be included in a simulation-based curriculum. A needs assessment using the Delphi method was completed among 91 key leaders in radiology. Round 1 identified technical procedures that radiologists should learn. Round 2 explored frequency of procedure, number of radiologists performing the procedure, risk and/or discomfort for patients, and feasibility for simulation. Round 3 was elimination and prioritization of procedures. Response rates were 67 %, 70 % and 66 %, respectively. In Round 1, 22 technical procedures were included. Round 2 resulted in pre-prioritization of procedures. In round 3, 13 procedures were included in the final prioritized list. The three highly prioritized procedures were ultrasound-guided (US) histological biopsy and fine-needle aspiration, US-guided needle puncture and catheter drainage, and basic abdominal ultrasound. A needs assessment identified and prioritized 13 technical procedures to include in a simulation-based curriculum. The list may be used as guide for development of training programs. • Simulation-based training can supplement training on patients in radiology. • Development of simulation-based training should follow a structured approach. • The CAMES Needs Assessment Formula explores needs for simulation training. • A national Delphi study identified and prioritized procedures suitable for simulation training. • The prioritized list serves as guide for development of courses in radiology.

Exposure to buffer solution alters tendon hydration and mechanics.

Science.gov (United States)

Safa, Babak N; Meadows, Kyle D; Szczesny, Spencer E; Elliott, Dawn M

2017-08-16

A buffer solution is often used to maintain tissue hydration during mechanical testing. The most commonly used buffer solution is a physiological concentration of phosphate buffered saline (PBS); however, PBS increases the tissue's water content and decreases its tensile stiffness. In addition, solutes from the buffer can diffuse into the tissue and interact with its structure and mechanics. These bathing solution effects can confound the outcome and interpretation of mechanical tests. Potential bathing solution artifacts, including solute diffusion, and their effect on mechanical properties, are not well understood. The objective of this study was to measure the effects of long-term exposure of rat tail tendon fascicles to several concentrations (0.9-25%) of NaCl, sucrose, polyethylene glycol (PEG), and SPEG (NaCl+PEG) solutions on water content, solute diffusion, and mechanical properties. We found that with an increase in solute concentration the apparent water content decreased for all solution types. Solutes diffused into the tissue for NaCl and sucrose, however, no solute diffusion was observed for PEG or SPEG. The mechanical properties changed for both NaCl solutions, in particular after long-term (8h) incubation the modulus and equilibrium stress decreased compared to short-term (15min) for 25% NaCl, and the cross sectional area increased for 0.9% NaCl. However, the mechanical properties were unchanged for both PEG and SPEG except for minor alterations in stress relaxation parameters. This study shows that NaCl and sucrose buffer solutions are not suitable for long-term mechanical tests. We therefore propose using PEG or SPEG as alternative buffer solutions that after long-term incubation can maintain tissue hydration without solute diffusion and produce a consistent mechanical response. Copyright © 2017 Elsevier Ltd. All rights reserved.

Determination of Selection Method in Genetic Algorithm for Land Suitability

Directory of Open Access Journals (Sweden)

Irfianti Asti Dwi

2016-01-01

Full Text Available Genetic Algoirthm is one alternative solution in the field of modeling optimization, automatic programming and machine learning. The purpose of the study was to compare some type of selection methods in Genetic Algorithm for land suitability. Contribution of this research applies the best method to develop region based horticultural commodities. This testing is done by comparing the three methods on the method of selection, the Roulette Wheel, Tournament Selection and Stochastic Universal Sampling. Parameters of the locations used in the test scenarios include Temperature = 27°C, Rainfall = 1200 mm, hummidity = 30%, Cluster fruit = 4, Crossover Probabiitiy (Pc = 0.6, Mutation Probabilty (Pm = 0.2 and Epoch = 10. The second test epoch incluides location parameters consist of Temperature = 30°C, Rainfall = 2000 mm, Humidity = 35%, Cluster fruit = 5, Crossover Probability (Pc = 0.7, Mutation Probability (Pm = 0.3 and Epoch 10. The conclusion of this study shows that the Roulette Wheel is the best method because it produces more stable and fitness value than the other two methods.

Existence of solutions to boundary value problem of fractional differential equations with impulsive

Directory of Open Access Journals (Sweden)

Weihua JIANG

2016-12-01

Full Text Available In order to solve the boundary value problem of fractional impulsive differential equations with countable impulses and integral boundary conditions on the half line, the existence of solutions to the boundary problem is specifically studied. By defining suitable Banach spaces, norms and operators, using the properties of fractional calculus and applying the contraction mapping principle and Krasnoselskii's fixed point theorem, the existence of solutions for the boundary value problem of fractional impulsive differential equations with countable impulses and integral boundary conditions on the half line is proved, and examples are given to illustrate the existence of solutions to this kind of equation boundary value problems.

Activities identification for activity-based cost/management applications of the diagnostics outpatient procedures.

Science.gov (United States)

Alrashdan, Abdalla; Momani, Amer; Ababneh, Tamador

2012-01-01

One of the most challenging problems facing healthcare providers is to determine the actual cost for their procedures, which is important for internal accounting and price justification to insurers. The objective of this paper is to find suitable categories to identify the diagnostic outpatient medical procedures and translate them from functional orientation to process orientation. A hierarchal task tree is developed based on a classification schema of procedural activities. Each procedure is seen as a process consisting of a number of activities. This makes a powerful foundation for activity-based cost/management implementation and provides enough information to discover the value-added and non-value-added activities that assist in process improvement and eventually may lead to cost reduction. Work measurement techniques are used to identify the standard time of each activity at the lowest level of the task tree. A real case study at a private hospital is presented to demonstrate the proposed methodology. © 2011 National Association for Healthcare Quality.

Calculation of piping loads due to filling procedures; Berechnung von Rohrleitungsbelastungen durch Fuellvorgaenge

Energy Technology Data Exchange (ETDEWEB)

Swidersky, Harald; Thiele, Thomas [TUeV Sued Industrie Service GmbH, Muenchen (Germany)

2012-11-01

Filling procedures in piping systems are usually not load cases that are studied by fluid dynamic and structure dynamic analyses with respect to the integrity of pipes and supports. Although, their frequency is higher than that of postulated accidental transients, therefore they have to be considered for fatigue analyses. The piping and support loads due to filling procedures are caused by the density differences if the transported fluids, for instance in flows with the transport of gas bubbles. The impact duration of the momentum forces is defined by the flow velocity and the length of discontinuities in the piping segments. Filling procedures end very often with a shock pressure, caused by the impact and decelerating of the fluid front at smaller cross sections. The suitability of the thermally hydraulics program RELAP/MOD3.3 for the calculation of realistic loads from filling procedures was studied, the results compared with experimental data. It is shown that dependent on the discretization level the loads are partial significantly underestimated.

A Differential Quadrature Procedure with Regularization of the Dirac-delta Function for Numerical Solution of Moving Load Problem

Directory of Open Access Journals (Sweden)

S. A. Eftekhari

Full Text Available AbstractThe differential quadrature method (DQM is one of the most elegant and efficient methods for the numerical solution of partial differential equations arising in engineering and applied sciences. It is simple to use and also straightforward to implement. However, the DQM is well-known to have some difficulty when applied to partial differential equations involving singular functions like the Dirac-delta function. This is caused by the fact that the Dirac-delta function cannot be directly discretized by the DQM. To overcome this difficulty, this paper presents a simple differential quadrature procedure in which the Dirac-delta function is replaced by regularized smooth functions. By regularizing the Dirac-delta function, such singular function is treated as non-singular functions and can be easily and directly discretized using the DQM. To demonstrate the applicability and reliability of the proposed method, it is applied here to solve some moving load problems of beams and rectangular plates, where the location of the moving load is described by a time-dependent Dirac-delta function. The results generated by the proposed method are compared with analytical and numerical results available in the literature. Numerical results reveal that the proposed method can be used as an efficient tool for dynamic analysis of beam- and plate-type structures traversed by moving dynamic loads.

BPS Lorentz-violating vortex solutions

International Nuclear Information System (INIS)

Casana, Rodolfo; Ferreira Junior, Manoel M.; Hora, E. da

2011-01-01

In this work, we deal with the construction of static Bogomol'nyi-Prasad-Sommerfield (BPS) rotationally symmetric configurations on the dimensional CPT-even Lorentz-breaking photonic sector of the Standard Model Extension (SME). The main objective of this presentation is to show the possibility of obtaining such BPS solutions, even in the presence of a Lorentz-violating background. A secondary objective is to analyze the effects of this background on such topologically non-trivial BPS configurations. In order to obtain these results, we deal with some specific components of Lorentz-violating field, handling with the static Euler-Lagrange equation of motion to gauge field, from which we fix temporal gauge (absence of electric field) as a proper gauge choice. Also, considering this equation, we consistently determine an interesting configuration (discarding non-interesting ones) to the Lorentz-breaking sector. Using this configuration and the standard rotationally symmetric vortex Ansatz (which describes the behaviors of Higgs and gauge fields via two profile functions, g(r) and a(r), respectively), we construct a rotationally symmetric expression to the energy density of the system. To obtain BPS solutions, we rewrite this expression in order to have static vortex solutions satisfying a set of first order differential equations (BPS ones). The existence of such solutions is strongly constrained by a relation between some parameters of the model, including the Lorentz-breaking one. Naturally, we show that the total energy of these BPS solutions is proportional to their magnetic flux, which is quantized according to their winding number. Using suitable boundary conditions (near the origin and asymptotically), we numerically integrate the BPS equations (by means of the shooting method). By this way, we obtain solutions for some physical quantities (Higgs field, magnetic field and energy density) for several values of the Lorentz-violating parameters. From these

Is rewritten Bible/Scripture the solution to the Synoptic Problem?

Directory of Open Access Journals (Sweden)

Gert J. Malan

2014-05-01

Full Text Available New Testament scholars have for centuries posited different solutions to the Synoptic Problem. Recently a new solution was proposed. Mogens Müller applies Geza Vermes’s term rewritten Bible to the canonical gospels. Accepting Markan priority, he views Matthew as rewritten Mark, Luke as rewritten Matthew, and John as additional source. This article examines Müller’s hypothesis by first investigating the history of the controversial term rewritten Bible/Scripture and its recent application to the New Testament Gospels. Müller’s hypothesis is then compared to other solutions to the Synoptic Problem, such as the Augustine, Griesbach, and Farrer-Goulder Hypotheses. The Two Document Hypothesis is discussed and Müller’s 2nd century Luke theory is compared to Burton Mack’s almost similar stance and tested with the argument of synoptic intertextuality in view of the possible but improbable early second century date for Matthew. Lastly, the relationship between the synoptic Gospels is viewed in terms of literary intertextuality. Müller suggests proclamation as motivation for the Gospels’ deliberate intertextual character. This notion is combined with the concept of intertextuality to suggest a more suitable explanation for the relationship between die Gospels, namely intertextual kerugma. This broad concept includes any form of intertextuality in terms of text and context regarding the author and readers. It suitably replaces rewritten Bible, both in reference to genre and textual (exegetical strategy.

Development of procedural requirements for life extension of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Lee, Sang Hun; Son, Moon Kyu [Korea Association for Nuclear Technology, Taejon (Korea, Republic of); Ham, Cheol Hun [The Catholic University of Korea, Seoul (Korea, Republic of); Chang, Keun Sun [Sunmoon Univ., Asan (Korea, Republic of); Paek, Won Phil [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Cheong, Ji Hwan [Baekseok College Cultural Studies, Cheonan (Korea, Republic of)

2001-03-15

Current status of regulatory aspects of life extension and upgrading of NPPs is reviewed for major foreign countries. Most countries require similar technical requirements; however, procedural aspects differ country by country. Regulatory systems suitable for NPP life extension is investigated. The procedure and requirements for reassessment of design life should be established first; then it can be incorporated into the PSR system. The concept of 'Current Licensing Basis (CLB)' can be adopted in Korea, but further elaboration for terms and definitions is needed for common understanding between interested groups. The procedure for maintenance and backfitting should also be improved. The Systems, Structures, and Components (SSCs) that require development of regulatory requirements for life extension are identified based on extensive analysis of foreign experiences. By analyzing the rules and regulations related to life extension. Basic directions are suggested to harmonize or establish regulatory systems for life extension, two-step licensing, PSR, and backfitting.

Solution of the neutron transport problem with anisotropic scattering in cylindrical geometry by the decomposition method

International Nuclear Information System (INIS)

Goncalves, G.A.; Bogado Leite, S.Q.; Vilhena, M.T. de

2009-01-01

An analytical solution has been obtained for the one-speed stationary neutron transport problem, in an infinitely long cylinder with anisotropic scattering by the decomposition method. Series expansions of the angular flux distribution are proposed in terms of suitably constructed functions, recursively obtainable from the isotropic solution, to take into account anisotropy. As for the isotropic problem, an accurate closed-form solution was chosen for the problem with internal source and constant incident radiation, obtained from an integral transformation technique and the F N method

The determination of phenazone in blood plasma for obtained sistem suitable test of monitoring drug level

Directory of Open Access Journals (Sweden)

Mochamad Lazuardi

2007-09-01

Full Text Available The determining of Phenazone to human blood plasma from healthy man after separated by solid phase extraction (SPE and spectroscopic measurements has been investigated. The objective of that research was to obtain system suitable test for determine the Phenazone level in biological fluids (human blood plasma, for new performed dosage regimented in clinical dentistry. The method can be divided into the following four steps. 1. Centrifugation the blood sample, 2. Extraction from blood plasma and, 3. Separation by SPE with manual pressured, 4. Elution to SPE followed by the measurement on a spectrophotometer in the ultra violet region. The critical value of  │t │at the 5% confidence level indicates that there is no systematic error in the linearity proposed method. Recoveries for this research were obtained at ranging 93.460 to 95.598%. The coefficient variation precision of this procedure was clearly good at smallest than 2%. The analytical procedure can be carried out in one working operation as a monitored therapeutic activity.

Determination of sulphur-35 impurity in solutions of phosphorus-32

International Nuclear Information System (INIS)

Rodriguez Pasques, R.H.; Iglicki, F.A; Cittadini, P.E.

1982-01-01

A method has been developed in order to evaluate the activity of sulphur-35 impurity in solutions of phosphorus-32. The procedure is based on the precipitation on benzidine sulphate in acid solution and further purification by dissolving and reprecipitating under appropriate conditions. 35 S beta radiation is measured with and end-window gas counter. A correction for any remaining 32 P is determined by differential absorption through aluminum. (author) [es

Regional prediction of basin-scale brown trout habitat suitability

Directory of Open Access Journals (Sweden)

S. Ceola

2014-09-01

Full Text Available In this study we propose a novel method for the estimation of ecological indices describing the habitat suitability of brown trout (Salmo trutta. Traditional hydrological tools are coupled with an innovative regional geostatistical technique, aiming at the prediction of the brown trout habitat suitability index where partial or totally ungauged conditions occur. Several methods for the assessment of ecological indices are already proposed in the scientific literature, but the possibility of exploiting a geostatistical prediction model, such as Topological Kriging, has never been investigated before. In order to develop a regional habitat suitability model we use the habitat suitability curve, obtained from measured data of brown trout adult individuals collected in several river basins across the USA. The Top-kriging prediction model is then employed to assess the spatial correlation between upstream and downstream habitat suitability indices. The study area is the Metauro River basin, located in the central part of Italy (Marche region, for which both water depth and streamflow data were collected. The present analysis focuses on discharge values corresponding to the 0.1-, 0.5-, 0.9-empirical quantiles derived from flow-duration curves available for seven gauging stations located within the study area, for which three different suitability indices (i.e. ψ10, ψ50 and ψ90 are evaluated. The results of this preliminary analysis are encouraging showing Nash-Sutcliffe efficiencies equal to 0.52, 0.65, and 0.69, respectively.

Regional prediction of basin-scale brown trout habitat suitability

Science.gov (United States)

Ceola, S.; Pugliese, A.

2014-09-01

In this study we propose a novel method for the estimation of ecological indices describing the habitat suitability of brown trout (Salmo trutta). Traditional hydrological tools are coupled with an innovative regional geostatistical technique, aiming at the prediction of the brown trout habitat suitability index where partial or totally ungauged conditions occur. Several methods for the assessment of ecological indices are already proposed in the scientific literature, but the possibility of exploiting a geostatistical prediction model, such as Topological Kriging, has never been investigated before. In order to develop a regional habitat suitability model we use the habitat suitability curve, obtained from measured data of brown trout adult individuals collected in several river basins across the USA. The Top-kriging prediction model is then employed to assess the spatial correlation between upstream and downstream habitat suitability indices. The study area is the Metauro River basin, located in the central part of Italy (Marche region), for which both water depth and streamflow data were collected. The present analysis focuses on discharge values corresponding to the 0.1-, 0.5-, 0.9-empirical quantiles derived from flow-duration curves available for seven gauging stations located within the study area, for which three different suitability indices (i.e. ψ10, ψ50 and ψ90) are evaluated. The results of this preliminary analysis are encouraging showing Nash-Sutcliffe efficiencies equal to 0.52, 0.65, and 0.69, respectively.

Mathematical Formulation and Comparison of Solution Approaches for the Vehicle Routing Problem with Access Time Windows

Directory of Open Access Journals (Sweden)

Rafael Grosso

2018-01-01

Full Text Available The application of the principles of sustainability to the implementation of urban freight policies requires the estimation of all the costs and externalities involved. We focus here on the case of access time windows, which ban the access of freight vehicles to central urban areas in many European cities. Even though this measure seeks to reduce congestion and emissions in the most crowded periods of the day, it also imposes additional costs for carriers and results in higher emissions and energy consumption. We present here a mathematical model for the Vehicle Routing Problem with Access Time Windows, a variant of the VRP suitable for planning delivery routes in a city subject to this type of accessibility restriction. We use the model to find exact solutions to small problem instances based on a case study and then compare the performance over larger instances of a modified savings algorithm, a genetic algorithm, and a tabu search procedure, with the results showing no clear prevalence of any of them, but confirming the significance of those additional costs and externalities.

Colony formation by sublethally heat-injured Zygosaccharomyces rouxii as affected by solutes in the recovery medium and procedure for sterilizing medium.

Science.gov (United States)

Golden, D A; Beuchat, L R

1990-01-01

Recovery and colony formation by healthy and sublethally heat-injured cells of Zygosaccharomyces rouxii as influenced by the procedure for sterilizing recovery media (YM agar [YMA], wort agar, cornmeal agar, and oatmeal agar) were investigated. Media were supplemented with various concentrations of glucose, sucrose, glycerol, or sorbitol and sterilized by autoclaving (110 degrees C, 15 min) and by repeated treatment with steam (100 degrees C). An increase in sensitivity was observed when heat-injured cells were plated on glucose-supplemented YMA at an aw of 0.880 compared with aws of 0.933 and 0.998. Colonies which developed from unheated and heated cells on YMA at aws of 0.998 and 0.933 generally exceeded 0.5 mm in diameter within 3.5 to 4 days of incubation at 25 degrees C, whereas colonies formed on YMA at an aw of 0.880 typically did not exceed 0.5 mm in diameter until after 5.5 to 6.5 days of incubation. The number of colonies exceeding 0.5 mm in diameter which were formed by heat-injured cells on YMA at an aw of 0.880 was 2 to 3 logs less than the total number of colonies detected, i.e., on YMA at an aw of 0.933 and using no limits of exclusion based on colony diameter. A substantial portion of cells which survived heat treatment were sublethally injured as evidenced by increased sensitivity to a suboptimum aw (0.880). In no instance was recovery of Z. rouxii significantly affected by medium sterilization procedure when glucose or sorbitol was used as the aw-suppressing solute.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:2403251

Colony formation by sublethally heat-injured Zygosaccharomyces rouxii as affected by solutes in the recovery medium and procedure for sterilizing medium.

Science.gov (United States)

Golden, D A; Beuchat, L R

1990-08-01

Recovery and colony formation by healthy and sublethally heat-injured cells of Zygosaccharomyces rouxii as influenced by the procedure for sterilizing recovery media (YM agar [YMA], wort agar, cornmeal agar, and oatmeal agar) were investigated. Media were supplemented with various concentrations of glucose, sucrose, glycerol, or sorbitol and sterilized by autoclaving (110 degrees C, 15 min) and by repeated treatment with steam (100 degrees C). An increase in sensitivity was observed when heat-injured cells were plated on glucose-supplemented YMA at an aw of 0.880 compared with aws of 0.933 and 0.998. Colonies which developed from unheated and heated cells on YMA at aws of 0.998 and 0.933 generally exceeded 0.5 mm in diameter within 3.5 to 4 days of incubation at 25 degrees C, whereas colonies formed on YMA at an aw of 0.880 typically did not exceed 0.5 mm in diameter until after 5.5 to 6.5 days of incubation. The number of colonies exceeding 0.5 mm in diameter which were formed by heat-injured cells on YMA at an aw of 0.880 was 2 to 3 logs less than the total number of colonies detected, i.e., on YMA at an aw of 0.933 and using no limits of exclusion based on colony diameter. A substantial portion of cells which survived heat treatment were sublethally injured as evidenced by increased sensitivity to a suboptimum aw (0.880). In no instance was recovery of Z. rouxii significantly affected by medium sterilization procedure when glucose or sorbitol was used as the aw-suppressing solute.(ABSTRACT TRUNCATED AT 250 WORDS)

Testing electrode suitability for field stimulation of high-threshold biological preparations

Directory of Open Access Journals (Sweden)

Hugo Fernando Maia Milan

Full Text Available IntroductionA problem posed by electrical field (E stimulation of biological preparations with high excitation threshold is that the E intensity required for excitation is likely to induce water electrolysis at the electrode surface, which can alter the extracellular medium and cause deleterious effects on the cells. In this study, different electrode materials and geometries were tested aiming at identifying electrode configurations that could transduce the E intensity required for exciting ventricular cardiomyocytes isolated from neonatal rats (threshold E ~30 V/cm without causing water electrolysis.MethodsWire and plate electrodes made of platinum, stainless steel and nickel/chrome alloy were used. The effect of blasting the electrode surface with sand and NaHCO3 solution was also tested. Electrodes were inserted into a cell perfusion chamber containing the saline solution routinely used for physiological experiments. During E application for 5 min, the electrode surface and its surroundings were examined at high magnification for the presence of microbubbles, which indicates the occurrence of water electrolysis. The greatest E intensity applied that failed to generate microbubbles (En was estimated.ResultsWhile nickel/chrome and stainless steel electrodes resulted in low En values, the best performance was observed for sandblasted platinum wire (2 mm diameter and plate (25 mm x 5 mm; 0.1 mm thickness electrodes, for which Enwas ≥40 V/cm.ConclusionThese electrode configurations are suitable for effective and safe stimulation of isolated neonatal cardiomyocytes.

Investigation of the use of Prandtl/Navier--Stokes equation procedures for two-dimensional incompressible flows

International Nuclear Information System (INIS)

Anderson, C.R.; Reider, M.B.

1994-01-01

The technique of combining solutions of the Prandtl equations with solutions of the Navier--Stokes equations to compute incompressible flow around two-dimensional bodies is investigated herein. Computational evidence is presented which shows that if the ''obvious'' coupling is used to combine the solutions, then the resulting solution is not accurate. An alternate coupling procedure is described which greatly improves the accuracy of the solutions obtained with the combined equation approach. An alternate coupling that can be used to create a more accurate vortex sheet/vortex blob method is then shown

MaSTiS, microorganism and solute transport in streams, model documentation and user manual

Science.gov (United States)

In-stream fate and transport of solutes and microorganisms need to be understood to evaluate suitability of waters for agricultural, recreational, and household uses and eventually minimize surface water contamination. Concerns over safety of this water resulted in development of predictive models f...

Anion-exchange Studies of Radioactive Trace Elements in Sulphuric Acid Solutions

Energy Technology Data Exchange (ETDEWEB)

Samsahl, K

1963-01-15

As part of a chemical group separation procedure used as a pretreatment in gamma spectrometric analysis, a study has been made of the adsorption from sulphuric acid solutions on strongly basic anion exchange resins, prepared in the hydroxide and the sulphate forms, of trace activities of Na, P, K, Ca, Sc, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Rb, Sr, Zr, Nb, Mo, Tc, Ag, Cd, In, Cs, Ba, La, Ce, Hf, Ta, W, Ir, Pa and Np. Besides adsorbing some of the trace elements in the solution, the anion exchange resin in the hydroxide form will neutralize the bulk of the sulphuric acid. This makes possible the subsequent sequential separation of chloride complexes on short anion-exchange columns by a stepwise increasing of the HCl concentration of the solution. On the basis of the results obtained in the present and earlier experiments, a new improved chemical group-separation procedure for mixtures of radioactive trace elements is outlined.

Quality Control Procedures Applied to the CMS Muon Chambers Built at CIEMAT

International Nuclear Information System (INIS)

Fouz, M. C.; Puerta Pelayo, J.

2004-01-01

In this document the quality control procedures applied to the CMS muon drift chambers built at CIEMAT are described. It includes a description of the high voltage and front electronics associated to the chambers. Every procedure is described with detail and a list of the more common problems and possible solutions is given. This document can be considered as a chamber test handbook for beginners. (Author) 3 refs

investigation of production conditions of ThO2-(%0-40)UO3 microspheres suitable for pellet production

International Nuclear Information System (INIS)

Tel, H.; Eral, M.; Altas, Y.

1997-01-01

The aim of the present study is to prepare homogeneous,sinterable and high density ThO 2 and thorium based (Th,U)O 2 pellets by using sol-gel transition. For the purpose to obtain of stable ThO 2 -UO 3 mixed sols suitable for gelling into crackfree microspheres, first the nitrate solutions of thorium and uranium at the different mol ratios of uranium (0, 5,10, 20, 30, 35 and 40 percent) were prepared. The sources sols used for the processes have been prepared by an ammonia addition method where starting nitrate solutions of thorium and uranium are heated and partially neutralized by aqueous ammonia under pH control at the different pH set and neutralization mode for each uranium mol ratio. Crackfree microspheres suitable for gelation were obtained by using hexone-10 % CCl 4 mixture as drop formation medium and ammonia as a gelling agent.Following the washing and aging, the formed gel microspheres were treated with IPA (isopropyl alcohol), dried at 85 o C and then heat-treated in air atmosphere at 300 o C.The dimensions, sphericity, bulk and apparent densities and specific surface area of microspheres were determined. Before the compaction the microspheres were exposed to air in a medium controlled at 30 o C and 85 % relative humidity and humidified to a moisture ratio > 18 % and then pelletized. The geometric densities of pellets were measured and then the pellets were sintered in 75 % Ar - 25 % H 2 atmosphere at 1090+-10 o C during 150 minutes

Multi-criteria Decision Analysis to Model Ixodes ricinus Habitat Suitability.

Science.gov (United States)

Rousseau, Raphaël; McGrath, Guy; McMahon, Barry J; Vanwambeke, Sophie O

2017-09-01

Tick-borne diseases present a major threat to both human and livestock health throughout Europe. The risk of infection is directly related to the presence of its vector. Thereby it is important to know their distribution, which is strongly associated with environmental factors: the presence and availability of a suitable habitat, of a suitable climate and of hosts. The present study models the habitat suitability for Ixodes ricinus in Ireland, where data on tick distribution are scarce. Tick habitat suitability was estimated at a coarse scale (10 km) with a multi-criteria decision analysis (MCDA) method according to four different scenarios (depending on the variables used and on the weights granted to each of them). The western part of Ireland and the Wicklow mountains in the East were estimated to be the most suitable areas for I. ricinus in the island. There was a good level of agreement between results from the MCDA and recorded tick presence. The different scenarios did not affect the spatial outputs substantially. The current study suggests that tick habitat suitability can be mapped accurately at a coarse scale in a data-scarce context using knowledge-based methods. It can serve as a guideline for future countrywide sampling that would help to determine local risk of tick presence and refining knowledge on tick habitat suitability in Ireland.

Piezometer installation and monitoring procedure: Revision 1

International Nuclear Information System (INIS)

1987-04-01

The Deaf Smith County (Texas) site has been selected by the US Department of Energy as one of three candidate sites for characterization to determine its suitability as a geologic repository for high-level nuclear waste. The installation and monitoring of piezometers has been identified as one of the tasks required during the development of an underground Exploratory Shaft Facility to satisfy specific information needs through a program of in situ testing, instrumentation and monitoring. The scope of piezometer installation and monitoring encompasses the installation of fluid pressure measuring equipment and the subsequent collection, presentation and interpretation of piezometric data from strata surrounding the Exploratory Shaft Facility (ESF) prior to, during and following construction of the ESF, and as part of geohydrologic testing within the ESF. This procedure describes the required instrumentation, equipment, and sequence of activities for piezometer installation in the ESF. The procedure also includes details on the data recording and presentation requirements, personnel responsibilities, test management and quality assurance. 16 refs., 12 figs., 2 tabs

Computer local construction of a general solution for the Chew-Low equations

International Nuclear Information System (INIS)

Gerdt, V.P.

1980-01-01

General solution of the dynamic form of the Chew-Low equations in the vicinity of the restpoint is considered. A method for calculating coefficients of series being members of such solution is suggested. The results of calculations, coefficients of power series and expansions carried out by means of the SCHOONSCHIP and SYMBAL systems are given. It is noted that the suggested procedure of the Chew-Low equation solutions basing on using an electronic computer as an instrument for analytical calculations permits to obtain detail information on the local structure of general solution

Development of residual stress analysis procedure for fitness-for-service assessment of welded structure

International Nuclear Information System (INIS)

Kim, Jong Sung; Jin, Tae Eun; Dong, P.; Prager, M.

2003-01-01

In this study, a state of art review of existing residual stress analysis techniques and representative solutions is presented in order to develop the residual stress analysis procedure for Fitness-For-Service(FFS) assessment of welded structure. Critical issues associated with existing residual stress solutions and their treatments in performing FFS are discussed. It should be recognized that detailed residual stress evolution is an extremely complicated phenomenon that typically involves material-specific thermomechanical/metallurgical response, welding process physics, and structural interactions within a component being welded. As a result, computational procedures can vary significantly from highly complicated numerical techniques intended only to elucidate a small part of the process physics to cost-effective procedures that are deemed adequate for capturing some of the important features in a final residual stress distribution. Residual stress analysis procedure for FFS purposes belongs to the latter category. With this in mind, both residual stress analysis techniques and their adequacy for FFS are assessed based on both literature data and analyses performed in this investigation

Approximated solutions to Born-Infeld dynamics

International Nuclear Information System (INIS)

Ferraro, Rafael; Nigro, Mauro

2016-01-01

The Born-Infeld equation in the plane is usefully captured in complex language. The general exact solution can be written as a combination of holomorphic and anti-holomorphic functions. However, this solution only expresses the potential in an implicit way. We rework the formulation to obtain the complex potential in an explicit way, by means of a perturbative procedure. We take care of the secular behavior common to this kind of approach, by resorting to a symmetry the equation has at the considered order of approximation. We apply the method to build approximated solutions to Born-Infeld electrodynamics. We solve for BI electromagnetic waves traveling in opposite directions. We study the propagation at interfaces, with the aim of searching for effects susceptible to experimental detection. In particular, we show that a reflected wave is produced when a wave is incident on a semi-space containing a magnetostatic field.

Approximated solutions to Born-Infeld dynamics

Energy Technology Data Exchange (ETDEWEB)

Ferraro, Rafael [Instituto de Astronomía y Física del Espacio (IAFE, CONICET-UBA),Casilla de Correo 67, Sucursal 28, 1428 Buenos Aires (Argentina); Departamento de Física, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires,Ciudad Universitaria, Pabellón I, 1428 Buenos Aires (Argentina); Nigro, Mauro [Departamento de Física, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires,Ciudad Universitaria, Pabellón I, 1428 Buenos Aires (Argentina)

2016-02-01

The Born-Infeld equation in the plane is usefully captured in complex language. The general exact solution can be written as a combination of holomorphic and anti-holomorphic functions. However, this solution only expresses the potential in an implicit way. We rework the formulation to obtain the complex potential in an explicit way, by means of a perturbative procedure. We take care of the secular behavior common to this kind of approach, by resorting to a symmetry the equation has at the considered order of approximation. We apply the method to build approximated solutions to Born-Infeld electrodynamics. We solve for BI electromagnetic waves traveling in opposite directions. We study the propagation at interfaces, with the aim of searching for effects susceptible to experimental detection. In particular, we show that a reflected wave is produced when a wave is incident on a semi-space containing a magnetostatic field.

Direct and iterative algorithms for the parallel solution of the one-dimensional macroscopic Navier-Stokes equations

International Nuclear Information System (INIS)

Doster, J.M.; Sills, E.D.

1986-01-01

Current efforts are under way to develop and evaluate numerical algorithms for the parallel solution of the large sparse matrix equations associated with the finite difference representation of the macroscopic Navier-Stokes equations. Previous work has shown that these equations can be cast into smaller coupled matrix equations suitable for solution utilizing multiple computer processors operating in parallel. The individual processors themselves may exhibit parallelism through the use of vector pipelines. This wor, has concentrated on the one-dimensional drift flux form of the Navier-Stokes equations. Direct and iterative algorithms that may be suitable for implementation on parallel computer architectures are evaluated in terms of accuracy and overall execution speed. This work has application to engineering and training simulations, on-line process control systems, and engineering workstations where increased computational speeds are required

PROCESS FOR RECOVERY OF URANIUM VALUES FROM IMPURE SOLUTIONS THEREOF

Science.gov (United States)

Kilner, S.B.

1959-11-01

A process is presented for the recovery of uraninm values from impure solutions which are obtained, for example, by washing residual uranium salt or uranium metal deposits from stainless steel surfaces using an aqueous or certain acidic aqueous solutions. The solutions include uranyl and oxidized iron, chromium, nickel, and copper ions and may contain manganese, zinc, and silver ions. In accordance with one procedure. the uranyl ions are reduced to the uranous state, and the impurity ions are complexed with cyanide under acidic conditions. The solution is then treated with ammonium hydroxide or alkali metal hydroxide to precipitate uranous hydroxide away from the complexed impurity ions in the solution. Alternatively, an excess of alkali metal cyanide is added to the reduced solution until the solution becomes sufficiently alkaline for the uranons hydroxide to precipitate. An essential feature in operating the process is in maintaining the pH of the solution sufficiently acid during the complexing operation to prevent the precipitation of the impurity metal hydroxides.

Parabolized Navier-Stokes solutions of separation and trailing-edge flows

Science.gov (United States)

Brown, J. L.

1983-01-01

A robust, iterative solution procedure is presented for the parabolized Navier-Stokes or higher order boundary layer equations as applied to subsonic viscous-inviscid interaction flows. The robustness of the present procedure is due, in part, to an improved algorithmic formulation. The present formulation is based on a reinterpretation of stability requirements for this class of algorithms and requires only second order accurate backward or central differences for all streamwise derivatives. Upstream influence is provided for through the algorithmic formulation and iterative sweeps in x. The primary contribution to robustness, however, is the boundary condition treatment, which imposes global constraints to control the convergence path. Discussed are successful calculations of subsonic, strong viscous-inviscid interactions, including separation. These results are consistent with Navier-Stokes solutions and triple deck theory.

Periodic solutions of nonlinear vibrating beams

Directory of Open Access Journals (Sweden)

J. Berkovits

2003-01-01

Full Text Available The aim of this paper is to prove new existence and multiplicity results for periodic semilinear beam equation with a nonlinear time-independent perturbation in case the period is not prescribed. Since the spectrum of the linear part varies with the period, the solvability of the equation depends crucially on the period which can be chosen as a free parameter. Since the period of the external forcing is generally unknown a priori, we consider the following natural problem. For a given time-independent nonlinearity, find periods T for which the equation is solvable for any T-periodic forcing. We will also deal with the existence of multiple solutions when the nonlinearity interacts with the spectrum of the linear part. We show that under certain conditions multiple solutions do exist for any small forcing term with suitable period T. The results are obtained via generalized Leray-Schauder degree and reductions to invariant subspaces.

Impact of vacancy-solute clusters on the aging of α-Fe solid solutions

International Nuclear Information System (INIS)

Schuler, Thomas

2015-01-01

Understanding and monitoring the aging of steels under vacancy supersaturation is a challenge of great practical interest for many industrial groups, and most of all for those related to nuclear energy. These steels always contain interstitial solutes, either as alloying elements or as impurities, and vacancies (V) that are equilibrium structural defects of materials. We have chosen the Fe-V -X system (X = C, N or O) as a model system for ferritic steels. Vacancy-solute clusters are likely to form in such systems because, despite the very low concentrations of their components, these cluster show very high attractive bonding. First of all, we have been working on the computation of intrinsic equilibrium properties of individual clusters, both thermodynamic (free binding energies) and kinetic (mobilities, dissociation coefficients, and their relationship with continuum diffusion) properties. Thanks to this atomic-scale characterization procedure, we have been able to highlight various effects of these clusters on a macroscopic system containing different cluster types: increase of solute solubility limits and total vacancy concentrations, flux couplings between interstitial solutes and vacancies, acceleration of solute precipitation kinetics and precipitate dissolution by solid solution stabilization due to vacancies. These results would not have been obtained without the development and/or extension of analytical methods in statistical physics which are able to describe cluster's components and their interactions at the atomic scale. Finally, we have also been working on cavities in α-iron, the study of which requires a different approach. Our study highlights the impact of the atomic discrete lattice on the equilibrium shape of cavities, and describes various kinetic mechanisms of these objects at the atomic scale. (author) [fr

Bentall Procedure Using Cryopreserved Valved Aortic Homografts

Science.gov (United States)

Christenson, Jan T.; Sierra, Jorge; Trindade, Pedro T.; Didier, Dominique; Kalangos, Afksendiyos

2004-01-01

The Bentall procedure is the standard operation for patients who have lesions of the ascending aorta associated with aortic valve disease. In many cases, however, mechanical prosthetic conduits are not suitable. There are few reports in the English-language medical literature concerning the mid- to long-term outcome of Bentall operations with cryopreserved homografts. Therefore, we reviewed our experience with this procedure and valved homografts. From January 1997 through December 2002, 21 patients underwent a Bentall operation with cryopreserved homografts at our institution. There were 14 males and 7 females; the mean age was 36 ± 21 years (range, 15–74 years). Eleven patients had undergone previous aortic valve surgery. All patients had aortic dilatation or aneurysms involving the ascending aorta. Indications for surgery included aortic valve stenosis or insufficiency, and aortic valve endocarditis (native valve or prosthetic). One patient had Takayasu's arteritis and 3 had Marfan syndrome. There was 1 hospital death (due to sepsis), but no other major postoperative complications. The mean hospital stay was 14 ± 7 days. Follow-up echocardiographic and computed tomographic scans were performed yearly. The mean follow-up was 34 months (6–72 months). Follow-up imaging revealed no calcifications or degenerative processes related to the homograft. Four patients had minimal valve regurgitation. Two patients died during follow-up. The 3-year actuarial survival rate was 85.7%. Our data suggest that the Bentall procedure with a valved homograft conduit is a safe procedure with excellent mid- to long-term results, comparable to results reported with aortic valve replacement with a homograft. PMID:15745290

Solution Methods for the Periodic Petrol Station Replenishment Problem

Directory of Open Access Journals (Sweden)

C Triki

2013-12-01

Full Text Available In this paper we introduce the Periodic Petrol Station Replenishment Problem (PPSRP over a T-day planning horizon and describe four heuristic methods for its solution. Even though all the proposed heuristics belong to the common partitioning-then-routing paradigm, they differ in assigning the stations to each day of the horizon. The resulting daily routing problems are then solved exactly until achieving optimalization. Moreover, an improvement procedure is also developed with the aim of ensuring a better quality solution. Our heuristics are tested and compared in two real-life cases, and our computational results show encouraging improvements with respect to a human planning solution

Perturbational blowup solutions to the compressible Euler equations with damping.

Science.gov (United States)

Cheung, Ka Luen

2016-01-01

The N-dimensional isentropic compressible Euler system with a damping term is one of the most fundamental equations in fluid dynamics. Since it does not have a general solution in a closed form for arbitrary well-posed initial value problems. Constructing exact solutions to the system is a useful way to obtain important information on the properties of its solutions. In this article, we construct two families of exact solutions for the one-dimensional isentropic compressible Euler equations with damping by the perturbational method. The two families of exact solutions found include the cases [Formula: see text] and [Formula: see text], where [Formula: see text] is the adiabatic constant. With analysis of the key ordinary differential equation, we show that the classes of solutions include both blowup type and global existence type when the parameters are suitably chosen. Moreover, in the blowup cases, we show that the singularities are of essential type in the sense that they cannot be smoothed by redefining values at the odd points. The two families of exact solutions obtained in this paper can be useful to study of related numerical methods and algorithms such as the finite difference method, the finite element method and the finite volume method that are applied by scientists to simulate the fluids for applications.

Improvement and Validation of Weld Residual Stress Modelling Procedure

International Nuclear Information System (INIS)

Zang, Weilin; Gunnars, Jens; Dong, Pingsha; Hong, Jeong K.

2009-06-01

The objective of this work is to identify and evaluate improvements for the residual stress modelling procedure currently used in Sweden. There is a growing demand to eliminate any unnecessary conservatism involved in residual stress assumptions. The study was focused on the development and validation of an improved weld residual stress modelling procedure, by taking advantage of the recent advances in residual stress modelling and stress measurement techniques. The major changes applied in the new weld residual stress modelling procedure are: - Improved procedure for heat source calibration based on use of analytical solutions. - Use of an isotropic hardening model where mixed hardening data is not available. - Use of an annealing model for improved simulation of strain relaxation in re-heated material. The new modelling procedure is demonstrated to capture the main characteristics of the through thickness stress distributions by validation to experimental measurements. Three austenitic stainless steel butt-welds cases are analysed, covering a large range of pipe geometries. From the cases it is evident that there can be large differences between the residual stresses predicted using the new procedure, and the earlier procedure or handbook recommendations. Previously recommended profiles could give misleading fracture assessment results. The stress profiles according to the new procedure agree well with the measured data. If data is available then a mixed hardening model should be used

Improvement and Validation of Weld Residual Stress Modelling Procedure

Energy Technology Data Exchange (ETDEWEB)

Zang, Weilin; Gunnars, Jens (Inspecta Technology AB, Stockholm (Sweden)); Dong, Pingsha; Hong, Jeong K. (Center for Welded Structures Research, Battelle, Columbus, OH (United States))

2009-06-15

The objective of this work is to identify and evaluate improvements for the residual stress modelling procedure currently used in Sweden. There is a growing demand to eliminate any unnecessary conservatism involved in residual stress assumptions. The study was focused on the development and validation of an improved weld residual stress modelling procedure, by taking advantage of the recent advances in residual stress modelling and stress measurement techniques. The major changes applied in the new weld residual stress modelling procedure are: - Improved procedure for heat source calibration based on use of analytical solutions. - Use of an isotropic hardening model where mixed hardening data is not available. - Use of an annealing model for improved simulation of strain relaxation in re-heated material. The new modelling procedure is demonstrated to capture the main characteristics of the through thickness stress distributions by validation to experimental measurements. Three austenitic stainless steel butt-welds cases are analysed, covering a large range of pipe geometries. From the cases it is evident that there can be large differences between the residual stresses predicted using the new procedure, and the earlier procedure or handbook recommendations. Previously recommended profiles could give misleading fracture assessment results. The stress profiles according to the new procedure agree well with the measured data. If data is available then a mixed hardening model should be used

Prilocaine hydrochloride 2% hyperbaric solution for intrathecal injection: a clinical review

Directory of Open Access Journals (Sweden)

Manassero A

2017-03-01

Full Text Available Alberto Manassero,1 Andrea Fanelli2 1Department of Emergency and Critical Care, Anesthesia and Intensive Care Unit, S. Croce e Carle Hospital, Cuneo, 2Department of Medical and Surgical Sciences, Anesthesia and Intensive Care Unit, Policlinico S. Orsola-Malpighi, Bologna, Italy Abstract: Prilocaine is a local anesthetic characterized by intermediate potency and duration and fast onset of action. As hyperbaric formulation of 5% solution, it was introduced and has been successfully used for spinal anesthesia since 1960. A new formulation of 2% plain and hyperbaric solution is currently available in Europe. Because of its lower incidence of transient neurological symptoms, prilocaine is suggested as substitute to lidocaine and mepivacaine in spinal anesthesia for ambulatory surgery, as well as a suitable alternative to low doses of long-acting local anesthetics. The National Library of Medicine database, the Excerpta Medica database, the Cochrane Database of Systematic Reviews, and the Cochrane Central Register of Controlled Trials database, were searched for the period 1970 to September 2016, with the aim to identify studies evaluating the intrathecal use of 2% prilocaine. A total of 13 randomized clinical trials (RCTs, 1 observational study, 2 dose finding, and 4 systematic reviews has been used for this review. The studies evaluated showed that 2% hyperbaric prilocaine due to a favorable anesthetic and safety profile is an alternative drug to lidocaine and mepivacaine for spinal anesthesia of intermediate or short duration. In comparison with plain solutions, hyperbaricity remarkably accelerates the onset and offset times of intrathecal 2% prilocaine. Literature suggests a dose ranging between 40 and 60 mg of prilocaine for lower extremities and lower abdominal procedures lasting up to 90 min, whereas a dose ranging from 10 to 30 mg is appropriate for perineal surgery. Readiness for discharge occurs in ~4 h from spinal administration. Keywords

Hybrid Accuracy-Time Trade-off Solution for Spectrum Sensing in Cognitive Radio Networks

DEFF Research Database (Denmark)

Ivanov, Antoni Stefkov; Mihovska, Albena Dimitrova; Poulkov, Vladimir

2018-01-01

parameters, therefore, a suitable trade-off is necessary for an optimal efficiency. We propose a dual-approach solution. The decision about the spectrum occupancy is made using the measured signal-to-noise ratio (SNR) and the received signal levels as inputs in a fuzzy logic algorithm. The result...

Suitability of online 3D visualization technique in oil palm plantation management

Science.gov (United States)

Mat, Ruzinoor Che; Nordin, Norani; Zulkifli, Abdul Nasir; Yusof, Shahrul Azmi Mohd

2016-08-01

Oil palm industry has been the backbone for the growth of Malaysia economy. The exports of this commodity increasing almost every year. Therefore, there are many studies focusing on how to help this industry increased its productivity. In order to increase the productivity, the management of oil palm plantation need to be improved and strengthen. One of the solution in helping the oil palm manager is by implementing online 3D visualization technique for oil palm plantation using game engine technology. The potential of this application is that it can helps in fertilizer and irrigation management. For this reason, the aim of this paper is to investigate the issues in managing oil palm plantation from the view of oil palm manager by interview. The results from this interview will helps in identifying the suitable issues could be highlight in implementing online 3D visualization technique for oil palm plantation management.

Return hospital visits and morbidity within 60 days after day surgery: a retrospective study of 18,736 day surgical procedures

DEFF Research Database (Denmark)

Engbaek, J; Bartholdy, J; Hjortsø, Carsten Nico Portefée

2006-01-01

As day surgery includes more extensive procedures focus should be put on late outcome. The frequency of day surgery-related return visits and the associated morbidity were examined to identify suitable indicators of quality....

Automation of procedure writing for the RLWTF

International Nuclear Information System (INIS)

Farnham, M.; MacDonald, A.

1998-01-01

In August of 1997, the Radioactive Liquid Waste Treatment Facility (RLWTF) at Los Alamos National Laboratory (LANL) recognized the need to re-engineer document management business process. All nuclear facilities at LANL are required to ensure that both the latest approved revision of controlled documents and any changes to those documents are available to operating personnel at all times. The Nuclear Materials Technology (NMT) Division was also re-engineering its document management business processes and searching for a solution. Both groups contacted several internal and external organizations in search of potential software solutions in use that would meet requirements. This report describes the objectives and features required by the software package, the choice of Procedure Design as the software package, and its implementation

Microprecipitation of barium sulfate as a suitable source for measurements of 226Ra by alpha spectrometry

International Nuclear Information System (INIS)

Fernandez-Cata, Geyser; Isaac-Olive, Keila : E-mail. geyser@instec.cu

2007-01-01

One of the most hazardous radionuclides released into the environment is the uranium's daughter 226 Ra. This nuclide behaves similar to calcium, therefore is highly toxic for humans. One of the suitable methods for its determination is alpha spectrometry. This technique, however, has as main drawback the source preparation which should be infinitely thin and massless, of regular, known, and reproducible shape, smaller in area than the active area of the detector and new (no sputtering or recoil losses). Among the various ways of preparing an alpha source are the electrodeposition and microprecipitation. Radium electrodeposition is not suitable to carry out because of the high reduction potential of this element, therefore non aqueous media is required and the chemical yield is not good. Radium however can be precipitated with barium sulfate and our previous work has shown that the precipitation is selective to this element in the presence of other alpha emitters such as uranium and polonium but divalent cations are incorporated to it. At the same time, manganese dioxide also precipitates radium free of divalent cations but alpha emitters such as uranium are present as well. The objective of this work was to establish a chemical procedure for the determination of 226 Ra in natural water by alpha spectrometry. The general methodology includes a preconcentration using a non selective coprecipitation via manganese dioxide (where cations are not included but alpha emitters do). Once the manganese dioxide is filtrated, it is re-dissolved and a selective microprecipitation using barium sulphate is carried out (where the only alpha emitter is radium). Details of the procedure, separation methods, source quality and discussion of the results will be given in the paper. (Author)

EXPERT MODEL OF LAND SUITABILITY ASSESSMENT FOR CROPS

Directory of Open Access Journals (Sweden)

Boris Đurđević

2010-12-01

Full Text Available A total of 17404 soil samples (2003rd-2009th year were analysed in the eastern Croatia. The largest number of soil samples belongs to the Osijek-Baranya county, which together with both Eastern sugar beet Factories (Osijek and Županja, conduct the soil fertility control (~4200 samples/yr.. Computer model suitability assessment for crops, supported by GIS, proved to be fast, efficient enough reliable in terms of the number of analyzed soil samples. It allows the visualization of the agricultural area and prediction of its production properties for the purposes of analysis, planning and rationalization of agricultural production. With more precise data about the soil (soil, climate and reliable Digital Soil Map of Croatia, the model could be an acceptable, not only to evaluate the suitability for growing different crops but also their need for fertilizer, necessary machinery, repairs (liming, and other measures of organic matter input. The abovementioned aims to eliminate or reduce effects of limiting factors in primary agricultural production. Assessment of the relative benefits of soil presented by computer model for the crops production and geostatistical method kriging in the Osijek-Baranya county showed: 1 Average soil suitability being 60.06 percent. 2 Kriging predicted that 51751 ha (17.16% are of limited resources (N1 for growing crops whereas a 86142 ha (28.57% of land is limited suitably (S3, b 132789 ha (44.04% are moderately suitable (S2 and c 30772 ha (10.28% are of excellent fertility (S1. A large number of eastern Croatian land data showed that the computer-geostatistical model for determination of soil benefits for growing crops was automated, fast and simple to use and suitable for the implementation of GIS and automatically downloading the necessary benefit indicators from the input base (land, analytical and climate as well as data from the digital soil maps able to: a visualize the suitability for soil tillage, b predict the

Numerical-solution package for transient two-phase-flow equations

International Nuclear Information System (INIS)

Mahaffy, J.H.; Liles, D.

1982-01-01

The methods presented have proven to be extremely reliable tools for reactor safety analysis. They can handle a wide range of fluid conditions and time scales with minimal failures, while maintaining time step sizes well above those possible with most other techniques. This robustness is due not only to the finite-difference equations themselves, but also to the choice of solution technique, because poorly chosen iterative solution procedures often require a limit on the time-step size for proper convergence of the iteration

Solution NMR structure determination of proteins revisited

International Nuclear Information System (INIS)

Billeter, Martin; Wagner, Gerhard; Wuethrich, Kurt

2008-01-01

This 'Perspective' bears on the present state of protein structure determination by NMR in solution. The focus is on a comparison of the infrastructure available for NMR structure determination when compared to protein crystal structure determination by X-ray diffraction. The main conclusion emerges that the unique potential of NMR to generate high resolution data also on dynamics, interactions and conformational equilibria has contributed to a lack of standard procedures for structure determination which would be readily amenable to improved efficiency by automation. To spark renewed discussion on the topic of NMR structure determination of proteins, procedural steps with high potential for improvement are identified

Technical suitability mapping of feedstocks for biological hydrogen production

NARCIS (Netherlands)

Panagiotopoulos, I.A.; Karaoglanoglou, L.S.; Koullas, D.P.; Bakker, R.R.; Claassen, P.A.M.; Koukios, E.G.

2015-01-01

The objective of this work was to map and compare the technical suitability of different raw materials for biological hydrogen production. Our model was based on hydrogen yield potential, sugar mobilization efficiency, fermentability and coproduct yield and value. The suitability of the studied

Recovery of copper and cyanide from waste cyanide solutions using emulsion liquid membrane with LIX 7950 as the carrier.

Science.gov (United States)

Xie, Feng; Wang, Wei

2017-08-01

The feasibility of using emulsion liquid membranes (ELMs) with the guanidine extractant LIX 7950 as the mobile carrier for detoxifying copper-containing waste cyanide solutions has been determined. Relatively stable ELMs can be maintained under suitable stirring speed during mixing ELMs and the external solution. Effective extraction of copper cyanides by ELMs only occurs at pH below 11. High copper concentration in the external phase and high volume ratio of the external phase to ELMs result in high transport rates of copper and cyanide. High molar ratio of cyanide to copper tends to suppress copper extraction. The presence of thiocyanate ion significantly depresses the transport of copper and cyanide through the membrane while the thiosulfate ion produces less impact on copper removal by ELMs. Zinc and nickel cyanides can also be effectively extracted by ELMs. More than 90% copper and cyanide can be effectively removed from alkaline cyanide solutions by ELMs under suitable experimental conditions, indicating the effectiveness of using the designed ELM for recovering copper and cyanide from waste cyanide solutions.

Exact solution of some linear matrix equations using algebraic methods

Science.gov (United States)

Djaferis, T. E.; Mitter, S. K.

1977-01-01

A study is done of solution methods for Linear Matrix Equations including Lyapunov's equation, using methods of modern algebra. The emphasis is on the use of finite algebraic procedures which are easily implemented on a digital computer and which lead to an explicit solution to the problem. The action f sub BA is introduced a Basic Lemma is proven. The equation PA + BP = -C as well as the Lyapunov equation are analyzed. Algorithms are given for the solution of the Lyapunov and comment is given on its arithmetic complexity. The equation P - A'PA = Q is studied and numerical examples are given.

Numerical Procedure for Optimizing Dye-Sensitized Solar Cells

Directory of Open Access Journals (Sweden)

Mihai Razvan Mitroi

2014-01-01

Full Text Available We propose a numerical procedure consisting of a simplified physical model and a numerical method with the aim of optimizing the performance parameters of dye-sensitized solar cells (DSSCs. We calculate the real rate of absorbed photons (in the dye spectral range Grealx by introducing a factor β<1 in order to simplify the light absorption and reflection on TCO electrode. We consider the electrical transport to be purely diffusive and the recombination process only to occur between electrons from the TiO2 conduction band and anions from the electrolyte. The used numerical method permits solving the system of differential equations resulting from the physical model. We apply the proposed numerical procedure on a classical DSSC based on Ruthenium dye in order to validate it. For this, we simulate the J-V characteristics and calculate the main parameters: short-circuit current density Jsc, open circuit voltage Voc, fill factor FF, and power conversion efficiency η. We analyze the influence of the nature of semiconductor (TiO2 and dye and also the influence of different technological parameters on the performance parameters of DSSCs. The obtained results show that the proposed numerical procedure is suitable for developing a numerical simulation platform for improving the DSSCs performance by choosing the optimal parameters.

Land Suitability Assessment for Sugarcane in "Herois de Caxito" (Angola

Directory of Open Access Journals (Sweden)

Baert, G.

2005-01-01

Full Text Available The suitability of the soils surrounding the sugarcane plantation at "Herois de Caxito" (7068 ha is assessed. The main goal is to identify land suitability for the enlargement of the present plantation, using FAO land evaluation models (modified to suit Herois de Caxito conditions and GIS. Calculations of the radiationthermal production potential (RPP, land production potential (LPP, irrigation suitability index, and evaluation of the irrigation water quality are done. The water-limited production potential (WPP is found equal to the RPP, because water needs were fully met under irrigation. Maps showing the spatial distribution of the LPP and the suitability for irrigation are generated. The matching of irrigation and fertility indices has shown that, about 40% of the soils with good fertility for sugarcane production present low suitability for irrigation, the main limitations being the very fine texture and the drainage. The available surface water at Herois de Caxito (Dande river is of very good quality for irrigation of sugarcane.

Digging into the Elusive Localised Solutions of (2+1) Dimensional sine-Gordon Equation

Science.gov (United States)

Radha, R.; Senthil Kumar, C.

2018-05-01

In this paper, we revisit the (2+1) dimensional sine-Gordon equation analysed earlier [R. Radha and M. Lakshmanan, J. Phys. A Math. Gen. 29, 1551 (1996)] employing the Truncated Painlevé Approach. We then generate the solutions in terms of lower dimensional arbitrary functions of space and time. By suitably harnessing the arbitrary functions present in the closed form of the solution, we have constructed dromion solutions and studied their collisional dynamics. We have also constructed dromion pairs and shown that the dynamics of the dromion pairs can be turned ON or OFF desirably. In addition, we have also shown that the orientation of the dromion pairs can be changed. Apart from the above classes of solutions, we have also generated compactons, rogue waves and lumps and studied their dynamics.

Habitat suitability modeling for the endangered Hawaiian petrel on Kauai and analysis of predicted habitat overlap with the Newell’s shearwater

Directory of Open Access Journals (Sweden)

Jeff R. Troy

2017-10-01

Full Text Available The endangered Hawaiian petrel (Pterodroma sandwichensis is endemic to the main Hawaiian Islands and has undergone a breeding range contraction since the arrival of humans. Using abiotic and biotic environmental variables, we developed a terrestrial habitat suitability model for the species on the island of Kauai based on contemporary sites where the species is known (or strongly suspected to nest, as well as a habitat/threat-isolation index that combined predictions from this suitability model with spatial information on two anthropogenic threats to the species. After accounting for large-scale relative spatial positioning of sites in modeling procedures, the habitat suitability model suggests that the probability that a location on Kauai could be suitable for Hawaiian petrel nesting activity increases with increasing mean annual wind speed, and may also increase somewhat with increasing slope and native vegetation cover. The habitat suitability model (which does not incorporate spatial information on anthropogenic threats to the species predicts approximately 74 km2 of Kauai, mostly in the interior of the island, as being potentially suitable with predicted probability > 0.7 for Hawaiian petrel terrestrial activity, and about 35 km2 with predicted probability > 0.9. Encouragingly, almost 50 km2 of land with predicted probability > 0.7 and almost 24 km2 with predicted probability > 0.9 is currently protected, being located on either government or private reserve land. Based on the habitat/threat-isolation index, most land predicted to be both suitable (based on environmental variables and as isolated from threats as a large number of the known contemporary Hawaiian petrel sites, is found in government and private reserves. Some degree of predicted habitat overlap between the Hawaiian petrel and Newell’s shearwater (Puffinus newelli, another Hawaiian seabird of conservation concern, suggests that some of the same larger tracts of land

Combined incomplete LU and strongly implicit procedure preconditioning

Energy Technology Data Exchange (ETDEWEB)

Meese, E.A. [Univ. of Trondheim (Norway)

1996-12-31

For the solution of large sparse linear systems of equations, the Krylov-subspace methods have gained great merit. Their efficiency are, however, largely dependent upon preconditioning of the equation-system. A family of matrix factorisations often used for preconditioning, is obtained from a truncated Gaussian elimination, ILU(p). Less common, supposedly due to it`s restriction to certain sparsity patterns, is factorisations generated by the strongly implicit procedure (SIP). The ideas from ILU(p) and SIP are used in this paper to construct a generalized strongly implicit procedure, applicable to matrices with any sparsity pattern. The new algorithm has been run on some test equations, and efficiency improvements over ILU(p) was found.

Lattice QCD and the Schwarz alternating procedure

CERN Document Server

Lüscher, Martin

2003-01-01

A numerical simulation algorithm for lattice QCD is described, in which the short- and long-distance effects of the sea quarks are treated separately. The algorithm can be regarded, to some extent, as an implementation at the quantum level of the classical Schwarz alternating procedure for the solution of elliptic partial differential equations. No numerical tests are reported here, but theoretical arguments suggest that the algorithm should work well also at small quark masses.

The Paperless Solution

Science.gov (United States)

2001-01-01

REI Systems, Inc. developed a software solution that uses the Internet to eliminate the paperwork typically required to document and manage complex business processes. The data management solution, called Electronic Handbooks (EHBs), is presently used for the entire SBIR program processes at NASA. The EHB-based system is ideal for programs and projects whose users are geographically distributed and are involved in complex management processes and procedures. EHBs provide flexible access control and increased communications while maintaining security for systems of all sizes. Through Internet Protocol- based access, user authentication and user-based access restrictions, role-based access control, and encryption/decryption, EHBs provide the level of security required for confidential data transfer. EHBs contain electronic forms and menus, which can be used in real time to execute the described processes. EHBs use standard word processors that generate ASCII HTML code to set up electronic forms that are viewed within a web browser. EHBs require no end-user software distribution, significantly reducing operating costs. Each interactive handbook simulates a hard-copy version containing chapters with descriptions of participants' roles in the online process.

Approximation of entropy solutions to degenerate nonlinear parabolic equations

Science.gov (United States)

Abreu, Eduardo; Colombeau, Mathilde; Panov, Evgeny Yu

2017-12-01

We approximate the unique entropy solutions to general multidimensional degenerate parabolic equations with BV continuous flux and continuous nondecreasing diffusion function (including scalar conservation laws with BV continuous flux) in the periodic case. The approximation procedure reduces, by means of specific formulas, a system of PDEs to a family of systems of the same number of ODEs in the Banach space L^∞, whose solutions constitute a weak asymptotic solution of the original system of PDEs. We establish well posedness, monotonicity and L^1-stability. We prove that the sequence of approximate solutions is strongly L^1-precompact and that it converges to an entropy solution of the original equation in the sense of Carrillo. This result contributes to justify the use of this original method for the Cauchy problem to standard multidimensional systems of fluid dynamics for which a uniqueness result is lacking.

Local existence of solutions to the Euler-Poisson system, including densities without compact support

Science.gov (United States)

Brauer, Uwe; Karp, Lavi

2018-01-01

Local existence and well posedness for a class of solutions for the Euler Poisson system is shown. These solutions have a density ρ which either falls off at infinity or has compact support. The solutions have finite mass, finite energy functional and include the static spherical solutions for γ = 6/5. The result is achieved by using weighted Sobolev spaces of fractional order and a new non-linear estimate which allows to estimate the physical density by the regularised non-linear matter variable. Gamblin also has studied this setting but using very different functional spaces. However we believe that the functional setting we use is more appropriate to describe a physical isolated body and more suitable to study the Newtonian limit.

Multiloop soliton and multibreather solutions of the short pulse model equation

International Nuclear Information System (INIS)

Matsuno, Yoshimasa

2007-01-01

We develop a systematic procedure for constructing the multisoliton solutions of the short pulse (SP) model equation which describes the propagation of ultra-short pulses in nonlinear medica. We first introduce a novel hodograph transformation to convert the SP equation into the sine-Gordon (sG) equation. With the soliton solutions of the sG equation, the system of linear partial differential equations governing the inverse mapping can be integrated analytically to obtain the soliton solutions of the SP equation in the form of the parametric representation. By specifying the soliton parameters, we obtain the multiloop and multibreather solutions. We investigate the asymptotic behavior of both solutions and confirm their solitonic feature. The nonsingular breather solutions may play an important role in studying the propagation of ultra-short pulses in an optical fibre. (author)

Is Switzerland Suitable for the Invasion of Aedes albopictus?

Science.gov (United States)

Neteler, Markus; Metz, Markus; Rocchini, Duccio; Rizzoli, Annapaola; Flacio, Eleonora; Engeler, Luca; Guidi, Valeria; Lüthy, Peter; Tonolla, Mauro

2013-01-01

Background Over the last 30 years, the Asian tiger mosquito, Aedes albopictus, has rapidly spread around the world. The European distribution comprises the Mediterranean basin with a first appearance in Switzerland in 2003. Early identification of the most suitable areas in Switzerland allowing progressive invasion by this species is considered crucial to suggest adequate surveillance and control plans. Methodology/Principal Findings We identified the most suitable areas for invasion and establishment of Ae. albopictus in Switzerland. The potential distribution areas linked to the current climatic suitability were assessed using remotely sensed land surface temperature data recorded by the MODIS satellite sensors. Suitable areas for adult survival and overwintering of diapausing eggs were also identified for future climatic conditions, considering two different climate change scenarios (A1B, A2) for the periods 2020–2049 and 2045–2074. At present, the areas around Lake Geneva in western Switzerland provide suitable climatic conditions for Ae. albopictus. In northern Switzerland, parts of the Rhine valley, around Lake Constance, as well as the surroundings of Lake Neuchâtel, appear to be suitable for the survival at least of adult Ae. albopictus. However, these areas are characterized by winters currently being too cold for survival and development of diapausing eggs. In southern Switzerland, Ae. albopictus is already well-established, especially in the Canton of Ticino. For the years 2020–2049, the predicted possible spread of the tiger mosquito does not differ significantly from its potential current distribution. However, important expansions are obtained if the period is extended to the years 2045–2074, when Ae. albopictus may invade large new areas. Conclusions/Significance Several parts of Switzerland provide suitable climatic conditions for invasion and establishment of Ae. albopictus. The current distribution and rapid spread in other European

Study of extraction chromatography methods of separation of neptunium and its radiometric determination

International Nuclear Information System (INIS)

Reich, M.

2009-04-01

elution solutions for securing the highest recovery of 239 Np were tested. Isolated 239 Np is suitable as a tracer for the determination of recovery of 237 Np after separation from environmental samples. This method is suitable for preparation of 239 Np generator because the radioactive equilibrium of mother radionuclide/daughter radionuclide occurs after relatively short period of time (33.6 d.). 5. The separation procedure was optimized in order to particular steps followed without useless steps like for example evaporation of solvent solution and subsequent change of chemical composition of system. 6. The scheme was optimised for reaching the highest recovery of separation 237 Np from matrix of model solution of known composition. The matrix of soils is complicated and recovery of 237 Np in separation process lower, but in measured alpha spectrum peaks coming from interfering radionuclides were not observed. The mass of soil sample for analyses influence the salinity of solution which caused decreasing the yield of 237 Np due to competing effect in separation process. 7 .The optimal composition of elution solution used in separation procedure was 0.5 mol.dm -3 HCI - 0.02 mol · dm -3 HF. This solution is compatible with solution suitable for preparation of sample for measuring of alpha activity by alpha spectrometry. It was not necessary to change solution for alpha sample preparation. 8. Dependencies of recoveries of neptunium separation from mass of soil sample and mass of present iron in model solution were observed. Increasing mass of soil sample and mass of iron in the model solution causes decreasing of the recoveries of neptunium. (author)

Suitable or optimal noise benefits in signal detection

International Nuclear Information System (INIS)

Liu, Shujun; Yang, Ting; Tang, Mingchun; Wang, Pin; Zhang, Xinzheng

2016-01-01

Highlights: • Six intervals of additive noises divided according to the two constraints. • Derivation of the suitable additive noise to meet the two constraints. • Formulation of the suitable noise for improvability or nonimprovability. • Optimal noises to minimize P FA , maximize P D and maximize the overall improvement. - Abstract: We present an effective way to generate the suitable or the optimal additive noises which can achieve the three goals of the noise enhanced detectability, i.e., the maximum detection probability (P D ), the minimum false alarm probability (P FA ) and the maximum overall improvement of P D and P FA , without increasing P FA and decreasing P D in a binary hypothesis testing problem. The mechanism of our method is that we divide the discrete vectors into six intervals and choose the useful or partial useful vectors from these intervals to form the additive noise according to different requirements. The form of the optimal noise is derived and proven as a randomization of no more than two discrete vectors in our way. Moreover, how to choose suitable and optimal noises from the six intervals are given. Finally, numerous examples are presented to illustrate the theoretical analysis, where the background noises are Gaussian, symmetric and asymmetric Gaussian mixture noise, respectively.

Procedural Content Graphs for Urban Modeling

Directory of Open Access Journals (Sweden)

Pedro Brandão Silva

2015-01-01

Full Text Available Massive procedural content creation, for example, for virtual urban environments, is a difficult, yet important challenge. While shape grammars are a popular example of effectiveness in architectural modeling, they have clear limitations regarding readability, manageability, and expressive power when addressing a variety of complex structural designs. Moreover, shape grammars aim at geometry specification and do not facilitate integration with other types of content, such as textures or light sources, which could rather accompany the generation process. We present procedural content graphs, a graph-based solution for procedural generation that addresses all these issues in a visual, flexible, and more expressive manner. Besides integrating handling of diverse types of content, this approach introduces collective entity manipulation as lists, seamlessly providing features such as advanced filtering, grouping, merging, ordering, and aggregation, essentially unavailable in shape grammars. Hereby, separated entities can be easily merged or just analyzed together in order to perform a variety of context-based decisions and operations. The advantages of this approach are illustrated via examples of tasks that are either very cumbersome or simply impossible to express with previous grammar approaches.

Use of variational principles for solution of infinitely redundant continuum problem with special reference to containment vessels

International Nuclear Information System (INIS)

Stefanou, G.D.

1982-01-01

The calculation of time-deepndent stresses in concrete structures operating at elevated temperatures is discussed. The method described is of a direct formulation technique and it is based on the principles of the calculus of variation. The paper mainly deals with the application of the method to a large and infinitely redundant continuum problem. The analytical procedure of the variational principle is also described and the mathematical expressions are developed for uniaxial and biaxial stress problems. The solution for the biaxial state of stress is carried out by a two-dimensional finite element stiffness analysis. A step-by-step method developed by the author using two-dimensional finite element stiffness analysis is also described in APPENDIX 3. Both methods are then applied to a real problem for which experimental data exist from Ref. (1) Predicted analytical values obtained by both methods are compared with experimental results. The method is suitable for predicting the distribution of stress in the end slabs of containment vessels. These slabs are perforated to permit fuel loading by the charging machine. (author)

Nonlinear reaction-diffusion equations with delay: some theorems, test problems, exact and numerical solutions

Science.gov (United States)

Polyanin, A. D.; Sorokin, V. G.

2017-12-01

The paper deals with nonlinear reaction-diffusion equations with one or several delays. We formulate theorems that allow constructing exact solutions for some classes of these equations, which depend on several arbitrary functions. Examples of application of these theorems for obtaining new exact solutions in elementary functions are provided. We state basic principles of construction, selection, and use of test problems for nonlinear partial differential equations with delay. Some test problems which can be suitable for estimating accuracy of approximate analytical and numerical methods of solving reaction-diffusion equations with delay are presented. Some examples of numerical solutions of nonlinear test problems with delay are considered.

Land Suitability Assessment for Pineapple Production in the A ...

African Journals Online (AJOL)

linking land resources assessment to any land use decision-making process. like elsewhere, land ... managers as decision-support tools, for instance, to outline the most suitable land areas for subsidy ...... increase rational decisions. In this ..... essentially dynamic. it is pertinent that land suitability analysis is framed within an ...

Numerical solutions of the Vlasov equation

International Nuclear Information System (INIS)

Satofuka, Nobuyuki; Morinishi, Koji; Nishida, Hidetoshi

1985-01-01

A numerical procedure is derived for the solutions of the one- and two-dimensional Vlasov-Poisson system equations. This numerical procedure consists of the phase space discretization and the integration of the resulting set of ordinary differential equations. In the phase space discretization, derivatives with respect to the phase space variable are approximated by a weighted sum of the values of the distribution function at properly chosen neighboring points. Then, the resulting set of ordinary differential equations is solved by using an appropriate time integration scheme. The results for linear Landau damping, nonlinear Landau damping and counter-streaming plasmas are investigated and compared with those of the splitting scheme. The proposed method is found to be very accurate and efficient. (author)

The general supersymmetric solution of topologically massive supergravity

International Nuclear Information System (INIS)

Gibbons, G W; Pope, C N; Sezgin, E

2008-01-01

We find the general fully nonlinear solution of topologically massive supergravity admitting a Killing spinor. It is of plane-wave type, with a null Killing vector field. Conversely, we show that all solutions with a null Killing vector are supersymmetric for one or the other choice of sign for the Chern-Simons coupling constant μ. If μ does not take the critical value, μ = ±1, these solutions are asymptotically regular on a Poincare patch, but do not admit a smooth global compactification with boundary S 1 x R. In the critical case, the solutions have a logarithmic singularity on the boundary of the Poincare patch. We derive a Nester-Witten identity, which allows us to identify the associated charges, but we conclude that the presence of the Chern-Simons term prevents us from making a statement about their positivity. The Nester-Witten procedure is applied to the BTZ black hole

Development of system on predicting uranium concentration from pregnant solution

International Nuclear Information System (INIS)

Yi Weiping

2004-01-01

Uranium concentration from pregnant solution is primary index of process for in-situ leaching of uranium, and the suitable method with which to predicate this index and effective means to solve it with were continuously studied hard. SPUC-system on predicting uranium concentration based on GM model of gray system theory is developed, and the mathematical model, constitution, function and theory foundation of this system are introduced. (authors)

Heap leaching procedure for the Uranium extraction

International Nuclear Information System (INIS)

Shishahbore, M. R.

2002-01-01

Heap leaching of Uranium ores is currently in use in several countries. Before taking any decision for construction of heap in industrial scale, it is necessary to obtain the main factors that influence the heap leaching process, such as acid construction, acid solution flowrate, temperature of reaction, or size, ration of liquid to solid, permeability and suitable oxidant. To achieve the above parameters, small scale column leaching is usually recommended. In this project column leaching were carried out in 6 plexiglass column with 43.5 cm an height and 7.4 cm inner diameter. In each column closely 2.00 kg Uranium ore were leached by sulfuric acid. Leaching operation on Iranian ores from two different anomalies from the same area were investigated. In this project, six column were leached at different flowrate of eluent and effect of oxidant were investigated. Acid consumption were in the range of 60 - 144 kg per ton ore and recovery between 73.07% - 99.97%. Finally according to the results obtained, investigated that over are suitable to heap leaching technique. Al tough, to enforce of heap leaching project need to more experiments

The soliton solution of the PHI24 field theory in the Hartree approximation

International Nuclear Information System (INIS)

Altenbokum, M.

1984-01-01

In this thesis in a simple model which possesses at the classical level a soliton solution a quantum-mechanical soliton sector shall be constructed in a Hartree-Fock approximation without application of semiclassical procedures. To this belongs beside the determination of the excitation spectrum of the applied Hamiltonian the knowledge of the corresponding infinitely-much eigenfunctions. The existing translational invariance of a classical soliton solution which implies the existence of a degenerated ground state by presence of a massless excitation is removed by quantum fluctuations. By removing of this degeneration conventional approximation procedures for this sector of the Hilbert space become for the first time immediately possible. (HSI) [de

Existence of solution for a general fractional advection-dispersion equation

Science.gov (United States)