WorldWideScience

Sample records for solute removal efficiency

  1. Investigation of Removal Efficiency of Nano Sized Alumina for Removal of Acid Red 18 from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    M.H. Dehghani

    2014-08-01

    Full Text Available Background and Objectives: Acid Red 18 dye was one of the Azo colors that are used in textile and dyeing industries. These dyes are often toxic and carcinogenic to humans and the environment as pollution. This study was conducted with the aim of investigating on nano alumina efficiency for removal of Acid Red 18 dye from aqueous solutions. Materials and Methods: This study was carried out in the laboratory scales and effect of The initial concentration of dye (25 to 100 mg/l, pH solution (3, 7, 11, nano alumina concentration (0.1, 0.4, 1, 1.5 g/l and contact time in range 5 to 240 min on dye removal efficiency were evaluated. Also kinetic and isotherm models of adsorption process were evaluated. Results: The high removal efficiency was observed in pH=3, contact time=60 min and Adsorbent concentration of 0.4 g/L. The rate of color removal were 63/24, 50/84 and 20 percent respectively at pH of 3, 7 and 11 for the initial dye concentration of 25 mg/l and 0.4 g/l mass absorbent that showing with increasing pH removal efficiency is reduced. the studied dye absorption isotherm was fitted Langmuir model (R2=0.994 which was 83.33 mg/g for maximum adsorption. The results from kinetic studies showed that removal of the studied dye was best described by pseudo-second order kinetic model (r2=0.999. Conclusion: The present study shows nano alumina powder is promising adsorbent for removal of Acid Red 18 from aqueous solution.

  2. Adsorption Efficiency of Iron Modified Carbons for Removal of Pb(II Ions from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Mohammad Hossein Salmani

    2016-06-01

    Full Text Available Abstract Introduction: The Lead causes severe damage to several systems of the body, especially to bony tissues. Until now, several low-cost biosorbents have been studied for removal of heavy metal ions from aqueous solutions. In the present study, carbonized pomegranate peels modified with Fe2+ and Fe3+ ions and then it was investigated for removal of Pb(II ions from aqueous solution. Materials and methods: the washed granola of pomegranate peel was separately socked with FeCl3 and FeCl2 solutions for 24 h. Then, the granules were carbonized at 400 ºC for 3 h in a programmable furnace in the atmosphere of nitrogen. The adsorption experiments were carried out for two types of iron-modified carbons by batch adsorption using one variable at a time procedures. Results: The optimum conditions were found as contact time 90 min, initial concentration 50 mg/l, and adsorbent dose, 1.00 g/100 ml solution. Maximum removal efficiency was calculated as 84% and 89% for Fe3+ and Fe2+ impregnated pomegranate peel carbons respectively. Conclusion: The iron treatment pomegranate peel carbons modified their surfaces for adsorption of heavy metals. The results showed that chemical modification of the low-cost adsorbents originating from agricultural waste has stood out for metal removal capabilities.

  3. Evaluations of Effective Factors on Efficiency Zinc Oxides Nanoparticles in Cadmium Removal from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    MH Ehrampoush

    2014-09-01

    Results: The results indicated that the adsorption process is affected by different parameters such as initial pollutant concentrations, adsorbent dose, pH, and contact time and Cadmiumremoval efficiency increases with increasing adsorbent dose and reaction time and decreases with increasing initial concentration of Cadmium. Therefore, it is observed that by raising the initial Cadmium concentration, the adsorption rate increases. The maximum efficiency of adsorptionin pH=7amounted to 89.6%. Conclusion: It is concluded that Zinc Oxide nanoparticles have proper efficiency in removal of Cadmium from aqueous solutions and can be used in the treatment of wastewater that contains ion Cadmium. However, its efficiency is deeply dependent on ion strength and the interaction of other metals in wastewater.

  4. The Efficiency of Inactive Saccharomyces Cerevisiae Biomass on Removing Arsenic from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    MH Ehrampoush

    2014-05-01

    Methods:This experimental study was performed in laboratory scale and was performed on 243 synthetic samples in a batch system. In this study the effect of parameters such as contact time (5,15,30,60,120,min and 24 h, pH (5,7,9, fluoride concentration (100, 250, 500, 750,1000 µg/l and absorbent dosages (0.5,1,2/5,5g/l was evaluated. Finally biosorption kinetic and equilibrium isotherms of adsorbent was investigated. Results: The removal efficiency of inactive Saccharomyces cerevisiae was 89.49% at pH 5, adsorbent dose of 1g/L and initial metal concentration of 100 mg/L. Maximum uptake was observed after the Contact time of 60 minutes. In addition absorption isotherm followed pseudo-second order model with a maximum R2 = 0.999. Conclusion:The results of study showed that biosorption efficiency decreases with increase in pH of solution. Optimum pH of biosorption was 5. The Removal efficiency of arsenic enhanced with increase in mass of Saccharomyces cerevisiae up to 1 g/L, but The Removal efficiency decreased with increase in initial concentration of arsenic. Maximum absorption was observed in 15 minutes.

  5. Investigation of Fluoride Removal Efficiency from Aqueous Solution by Pistachio and Almonds Crust

    Directory of Open Access Journals (Sweden)

    Maryam Khodadadi

    2015-06-01

    Full Text Available Introduction: Fluoride and its compounds are widely used in industries and then through effluent are released into the environment. The purpose of this study was to evaluate Efficiency of low cost adsorbents (pistachios coal in the removal of fluoride from aqueous solutions.  Methods: For the preparation of adsorbent, crust of pistachios deride, then washed with distilled water, then powder in the furnace for burning for 2 hours at temperatures of 500, 600, and 700 °C. The effect of changing pH, burning temperature of adsorbent, stirring speed, initial concentration of fluoride, retention time and adsorbent dose was studied. Concentration of fluoride measured according to standard method using spectrophotometer the data were analyzed using Excel software. Results: The results of these experiments showed that the burning adsorbent, temperature 500 ° C, PH of solution in the neutral range (pH = 7, adsorbent dose of 2 g/L for absorbing almonds and adsorbent dose of 3 g pistachio, contact time of 40 minutes for both adsorbent, initial fluoride concentration (5ppm for both absorbent without mixing, the optimal conditions for the efficiency of the absorber is as much as 90-80 percent. Discussion: According to the results, pistachio coal can be used with high efficiency for fluoride removal

  6. Efficient removal of Co(II) from aqueous solution by titanate sodium nanotubes

    Institute of Scientific and Technical Information of China (English)

    Dong-Mei Li; Ning Liu; Fei-Ze Li; Jia-Li Liao; Ji-Jun Yang; Bing Li; Yun-Ming Chen; Yuan-You Yang; Jin-Song Zhang; Jun Tang

    2016-01-01

    In this paper, a novel material for Co(II) adsorption, titanate sodium nanotubes (Na2Ti2O5-NTs) were synthesized and characterized, and then they were used to remove Co(II) from aqueous solution and compared with titanic acid nanotubes (H2Ti2O5-NTs) and potassium hexatitanate whiskers (K2Ti6O13). The results showed that the adsorption of Co(II) on the materials was dependent on pH values and was a spontaneous, endothermic process. Specifically, Na2Ti2O5-NTs exhibited much more efficient ability to adsorb Co(II) from aqueous solution, with the maximum adsorption capacity of 85.25 mg/g. Furthermore, Na2Ti2O5-NTs could selectively adsorb Co(II) from aque-ous solution containing coexisting ions (Na+, K+, Mg2+, and Ca2+). The results suggested that Na2Ti2O5-NTs were potential effective adsorbents for removal of Co(II) or cobalt-60 from wastewater.

  7. Removal of uranium from aqueous solution by a low cost and high-efficient adsorbent

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yun-Hai [State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang, 330013 (China); Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China); Wang, You-Qun [Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China); Zhang, Zhi-Bin, E-mail: zhangnjut@163.com [State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang, 330013 (China); Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China); Cao, Xiao-Hong; Nie, Wen-Bin; Li, Qin [Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China); Hua, Rong [State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang, 330013 (China); Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China)

    2013-05-15

    In this study, a low-cost and high-efficient carbonaceous adsorbent (HTC-COOH) with carboxylic groups was developed for U(VI) removal from aqueous solution compared with the pristine hydrothermal carbon (HTC). The structure and chemical properties of resultant adsorbents were characterized by Scanning electron microscope (SEM), N{sub 2} adsorption–desorption, Fourier transform-infrared spectra (FT-IR) and acid–base titration. The key factors (solution pH, contact time, initial U(VI) concentrations and temperature) affected the adsorption of U(VI) on adsorbents were investigated using batch experiments. The adsorption of U(VI) on HTC and HTC-COOH was pH-dependent, and increased with temperature and initial ion concentration. The adsorption equilibrium of U(VI) on adsorbents was well defined by the Langmuir isothermal equation, and the monolayer adsorption capacity of HTC-COOH was found to be 205.8 mg/g. The kinetics of adsorption was very in accordance with the pseudo-second-order rate model. The adsorption processes of U(VI) on HTC and HTC-COOH were endothermic and spontaneous in nature according to the thermodynamics of adsorption. Furthermore, HTC-COOH could selectively adsorption of U(VI) in aqueous solution containing co-existing ions (Mg{sup 2+}, Co{sup 2+}, Ni{sup 2+}, Zn{sup 2+} and Mn{sup 2+}). From the results of the experiments, it is found that the HTC-COOH is a potential adsorbent for effective removal of U(VI) from polluted water.

  8. Removal of uranium from aqueous solution by a low cost and high-efficient adsorbent

    Science.gov (United States)

    Liu, Yun-Hai; Wang, You-Qun; Zhang, Zhi-Bin; Cao, Xiao-Hong; Nie, Wen-Bin; Li, Qin; Hua, Rong

    2013-05-01

    In this study, a low-cost and high-efficient carbonaceous adsorbent (HTC-COOH) with carboxylic groups was developed for U(VI) removal from aqueous solution compared with the pristine hydrothermal carbon (HTC). The structure and chemical properties of resultant adsorbents were characterized by Scanning electron microscope (SEM), N2 adsorption-desorption, Fourier transform-infrared spectra (FT-IR) and acid-base titration. The key factors (solution pH, contact time, initial U(VI) concentrations and temperature) affected the adsorption of U(VI) on adsorbents were investigated using batch experiments. The adsorption of U(VI) on HTC and HTC-COOH was pH-dependent, and increased with temperature and initial ion concentration. The adsorption equilibrium of U(VI) on adsorbents was well defined by the Langmuir isothermal equation, and the monolayer adsorption capacity of HTC-COOH was found to be 205.8 mg/g. The kinetics of adsorption was very in accordance with the pseudo-second-order rate model. The adsorption processes of U(VI) on HTC and HTC-COOH were endothermic and spontaneous in nature according to the thermodynamics of adsorption. Furthermore, HTC-COOH could selectively adsorption of U(VI) in aqueous solution containing co-existing ions (Mg2+, Co2+, Ni2+, Zn2+ and Mn2+). From the results of the experiments, it is found that the HTC-COOH is a potential adsorbent for effective removal of U(VI) from polluted water.

  9. Efficient on-chip hotspot removal combined solution of thermoelectric cooler and mini-channel heat sink

    International Nuclear Information System (INIS)

    Hao, Xiaohong; Peng, Bei; Xie, Gongnan; Chen, Yi

    2016-01-01

    Highlights: • A combined solution of thermoelectric cooler (TEC) and mini-channel heat sink to remove the hotspot of the chip has been proposed. • The TEC's mathematical model is established to assess its work performance. • A comparative study on the proposed efficient On-Chip Hotspot Removal Combined Solution. - Abstract: Hotspot will significantly degrade the reliability and performance of the electronic equipment. The efficient removal of hotspot can make the temperature distribution uniform, and ensure the reliable operation of the electronic equipment. This study proposes a combined solution of thermoelectric cooler (TEC) and mini-channel heat sink to remove the hotspot of the chip in the electronic equipment. Firstly, The TEC's mathematical model is established to assess its work performance under different boundary conditions. Then, the hotspot removal capability of the TEC is discussed for different cooling conditions, which has shown that the combined equipment has better hotspot removal capability compared with others. Finally, A TEC is employed to investigate the hotspot removal capacity of the combined solution, and the results have indicated that it can effectively remove hotspot in the diameter of 0.5 mm, the power density of 600W/cm 2 when its working current is 3A and heat transfer thermal resistance is 0 K/W.

  10. Arsenic Removal Efficiency in Aqueous Solutions Using Reverse Osmosis and Zero-Valent Iron Nanoparticles

    Directory of Open Access Journals (Sweden)

    Niloofar Saboori

    2018-01-01

    Full Text Available Arsenic is one of the most hazardous pollutants of water resources which threaten human health as well as animals. Therefore arsenic removal from water resources is the priority of health programs. There are several ways to remove arsenic. In this study, reverse osmosis and zero-valent iron nanoparticles methods have been used in a laboratory scale. To perform the test, the variables of temperature, arsenic concentration, pH, iron nanoparticle concentration and mixing time were considered. The results indicated that in both methods of reverse osmosis and iron nanoparticle, through increasing arsenic concentration, arsenic removal efficiency has been also increased. At concentration of 1.5 mg per litre in reverse osmosis method, the maximum efficiency was achieved by 98% and 95.2% removal of arsenic respectively. The effect of temperature and pH were similar in reverse osmosis; by increasing these two variables, arsenic removal percentage also increased. The highest removal rates of 95.98% and 95.56% were observed at pH 9 and Temperature 30oC respectively. The results indicated that in iron nanoparticles method the arsenic removal efficiency increases by increasing mixing time and temperature, while it decreases with increasing pH.

  11. Efficiency of Dry (Psidium guava) Leaves for The Removal of Cesium-137 from Aqueous Solutions

    International Nuclear Information System (INIS)

    Omar, H.A.; Abu-Kharda, S.A.; Abd El -Baset, L.A.; Abu-Shohba, R.M.

    2012-01-01

    Batch experiments for the removal of cesium-137 from aqueous solution onto guava leaves (psidium guava) and carbonized guava leaves were studied as a function of contact time, dosage, ph value and initial concentration ion. The sorption process was described by pseudo first-order, pseudo second-order, Morris and Elovich kinetic models. Cesium concentrations were ranged between 2x10 -5 - 1x10 -3 M. Sorption data have been interpreted in terms of Langmuir, Freundlich and Dubinin-Radushkevich isotherms. The maximum sorption capacity of carbonized guava leaves adsorbent for cesium removal was 8.02 mgg -1 . The results of the present study suggest that carbonized guava leaves can be used beneficially for cesium removal from aqueous solution.

  12. The Investigation of Electron Beam Catalytical Oxidation Process Efficiency with Potassium Persulfate in Removal Humic Acid from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    MT Ghaneian

    2015-05-01

    Results: Based on the results, changes in pH had little effect on the Humic acid removal efficiency. The average, with increasing of pH from 4 to 10, the removal efficiency of humic acid from 72.59% to 73.36% increased, respectively. The results showed that increasing of the dose from 1 to 15 kGy, humic acid removal efficiency increases. Based on results by increasing of persulfate concentration, the removal efficiency increased so that with increasing of concentration of potassium persulfate from 0.1 to 0.5 mmol/100cc, removal efficiency from 69.43% to 83.82% was increased. Kinetic experiments showed that the decomposition of humic acid by electron beam radiation followed the second-order kinetic. Conclusion: The data from this study showed that the aqueous solution containing acid Humic is decomposed effectively by electron beams irradiation. Addition of potassium persulfate can be have significant improvements in removal efficiency of humic acid in the presence of electron beam.

  13. Evaluation of natural zeolite clinoptilolite efficiency for the removal of ammonium and nitrate from aquatic solutions

    Directory of Open Access Journals (Sweden)

    Mozhdeh Murkani

    2015-01-01

    Full Text Available Background: Surface water and groundwater pollution with various forms of nitrogen such as ammonium and nitrate ions is one of the main environmental risks. The major objectives of this study were to evaluate the capacity of natural zeolite (clinoptilolite to remove NO3– and NH4+ from polluted water under both batch and column conditions. Methods: The laboratory batch and column experiments were conducted to investigate the feasibility of clinoptilolite as the adsorbent for removal of nitrate (NO3– and ammonium (NH4+ ions from aqueous solution. The effects of pH, clinoptilolite dosage, contact time, and initial metal ion concentration on NO3– and NH4+ removal were investigated in a batch system. Results: Equilibrium time for NO3– and NH4+ ions exchange was 60 minutes and the optimum adsorbent dosage for their removal was 1 and 2.5 g/L, respectively. The adsorption isotherm of reaction (r> 0.9 and optimum entered concentration of ammonium and nitrate (30 and 6.5 mg/L, respectively were in accordance with Freundlich isotherm model. The ammonium removal rate increased by 98% after increasing the contact time. Conclusion: Our findings confirmed that natural Clinoptilolite can be used as one of effective, suitable, and low-costing adsorbent for removing ammonium from polluted waters.

  14. High Efficient Nanocomposite for Removal of Heavy Metals (Hg2+ and Pb2+ from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    M. Ebadi

    2016-01-01

    Full Text Available In current work, CdS/black carbon nanocomposites were successfully synthesized with the aid of chestnut and cadmium nitrate as the starting reagents. Besides, the effects of preparation parameters such as reaction time, and precursor concentration on the morphology of products and removal of heavy metals (Hg+2, Pb+2 were studied by scanning electron microscopy images and batch adsorption mode. CdS/black carbon nanocomposite introduced as new and high efficient system for removal of heavy metal ions. The as-synthesized products were characterized by powder X-ray diffraction, scanning electron microscopy, and spectra energy dispersive analysis of X-ray.

  15. Synthesis of Zero Valent Iron Nanoparticles (nZVI and its Efficiency in Arsenic Removal from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Ali Reza Rahmani

    2011-03-01

    Full Text Available The aim of this study to synthesize nanoparticle zero valent iron and to determine its efficiency in arsenic removal from aqueous solutions. Nanoparticles were synthesized by reduction of ferric chloride using sodium borohydrid. The experiments were conducted in a batch system and the effects of pH, contact time, and the concentrations of arsenit, arsenat, and nano zero valent iron were investigated. SEM and XRD were applied for the determination of particle size and characterization of the nanoparticles synthesized. SEM results revealed that synthesized particles were of nano size (1-100 nanometers. At pH=7.0, 99% of arsenit and arsenat was removed when nano zero valent iron concentration was 1 (g L-1  over a retention time of  10 min. Based on the results obtained, the removal efficiency was enhanced with increasing nano zero valent iron dosage and reaction time, but decreased with increasing initial concentration and initial solution pH. The significant removal efficiency, high rate of process and short reaction time showed that iron nano particles are of a significant potential for the removal of arsenic from aqueous solutions.

  16. Efficiency Evaluation of Food Waste Materials for the Removal of Metals and Metalloids from Complex Multi-Element Solutions

    Science.gov (United States)

    Giuliano, Antonella; Astolfi, Maria Luisa; Congedo, Rossana; Masotti, Andrea; Canepari, Silvia

    2018-01-01

    Recent studies have shown the potential of food waste materials as low cost adsorbents for the removal of heavy metals and toxic elements from wastewater. However, the adsorption experiments have been performed in heterogeneous conditions, consequently it is difficult to compare the efficiency of the individual adsorbents. In this study, the adsorption capacities of 12 food waste materials were evaluated by comparing the adsorbents’ efficiency for the removal of 23 elements from complex multi-element solutions, maintaining homogeneous experimental conditions. The examined materials resulted to be extremely efficient for the adsorption of many elements from synthetic multi-element solutions as well as from a heavy metal wastewater. The 12 adsorbent surfaces were analyzed by Fourier transform infrared spectroscopy and showed different types and amounts of functional groups, which demonstrated to act as adsorption active sites for various elements. By multivariate statistical computations of the obtained data, the 12 food waste materials were grouped in five clusters characterized by different elements’ removal efficiency which resulted to be in correlation with the specific adsorbents’ chemical structures. Banana peel, watermelon peel and grape waste resulted the least selective and the most efficient food waste materials for the removal of most of the elements. PMID:29495363

  17. Efficiency Evaluation of Food Waste Materials for the Removal of Metals and Metalloids from Complex Multi-Element Solutions.

    Science.gov (United States)

    Massimi, Lorenzo; Giuliano, Antonella; Astolfi, Maria Luisa; Congedo, Rossana; Masotti, Andrea; Canepari, Silvia

    2018-02-26

    Recent studies have shown the potential of food waste materials as low cost adsorbents for the removal of heavy metals and toxic elements from wastewater. However, the adsorption experiments have been performed in heterogeneous conditions, consequently it is difficult to compare the efficiency of the individual adsorbents. In this study, the adsorption capacities of 12 food waste materials were evaluated by comparing the adsorbents' efficiency for the removal of 23 elements from complex multi-element solutions, maintaining homogeneous experimental conditions. The examined materials resulted to be extremely efficient for the adsorption of many elements from synthetic multi-element solutions as well as from a heavy metal wastewater. The 12 adsorbent surfaces were analyzed by Fourier transform infrared spectroscopy and showed different types and amounts of functional groups, which demonstrated to act as adsorption active sites for various elements. By multivariate statistical computations of the obtained data, the 12 food waste materials were grouped in five clusters characterized by different elements' removal efficiency which resulted to be in correlation with the specific adsorbents' chemical structures. Banana peel, watermelon peel and grape waste resulted the least selective and the most efficient food waste materials for the removal of most of the elements.

  18. Efficiency Evaluation of Food Waste Materials for the Removal of Metals and Metalloids from Complex Multi-Element Solutions

    Directory of Open Access Journals (Sweden)

    Lorenzo Massimi

    2018-02-01

    Full Text Available Recent studies have shown the potential of food waste materials as low cost adsorbents for the removal of heavy metals and toxic elements from wastewater. However, the adsorption experiments have been performed in heterogeneous conditions, consequently it is difficult to compare the efficiency of the individual adsorbents. In this study, the adsorption capacities of 12 food waste materials were evaluated by comparing the adsorbents’ efficiency for the removal of 23 elements from complex multi-element solutions, maintaining homogeneous experimental conditions. The examined materials resulted to be extremely efficient for the adsorption of many elements from synthetic multi-element solutions as well as from a heavy metal wastewater. The 12 adsorbent surfaces were analyzed by Fourier transform infrared spectroscopy and showed different types and amounts of functional groups, which demonstrated to act as adsorption active sites for various elements. By multivariate statistical computations of the obtained data, the 12 food waste materials were grouped in five clusters characterized by different elements’ removal efficiency which resulted to be in correlation with the specific adsorbents’ chemical structures. Banana peel, watermelon peel and grape waste resulted the least selective and the most efficient food waste materials for the removal of most of the elements.

  19. Evaluation of removal efficiency of residual diclofenac in aqueous solution by nanocomposite tungsten-carbon using design of experiment.

    Science.gov (United States)

    Salmani, M H; Mokhtari, M; Raeisi, Z; Ehrampoush, M H; Sadeghian, H A

    2017-09-01

    Wastewater containing pharmaceutical residual components must be treated before being discharged to the environment. This study was conducted to investigate the efficiency of tungsten-carbon nanocomposite in diclofenac removal using design of experiment (DOE). The 27 batch adsorption experiments were done by choosing three effective parameters (pH, adsorbent dose, and initial concentration) at three levels. The nanocomposite was prepared by tungsten oxide and activated carbon powder in a ratio of 1 to 4 mass. The remaining concentration of diclofenac was measured by a spectrometer with adding reagents of 2, 2'-bipyridine, and ferric chloride. Analysis of variance (ANOVA) was applied to determine the main and interaction effects. The equilibrium time for removal process was determined as 30 min. It was observed that the pH had the lowest influence on the removal efficiency of diclofenac. Nanocomposite gave a high removal at low concentration of 5.0 mg/L. The maximum removal for an initial concentration of 5.0 mg/L was 88.0% at contact time of 30 min. The results of ANOVA showed that adsorbent mass was among the most effective variables. Using DOE as an efficient method revealed that tungsten-carbon nanocomposite has high efficiency in the removal of residual diclofenac from the aqueous solution.

  20. Efficient removal of Cd2+ from aqueous solutions using by-product of biodiesel production

    International Nuclear Information System (INIS)

    Ribeiro, Rita F.L.; Soares, Vitor C.; Costa, Letícia M.; Nascentes, Clésia C.

    2012-01-01

    Highlights: ► Sorbents were prepared from radish cake, a waste from biodiesel production. ► The chemical treatments used were simple, low-cost and enhanced the Cd 2+ sorption. ► The cadmium sorption process was evaluated by Freundlich and Langmuir models. ► Chemically treated radish cake is an excellent alternative for removal of Cd 2+ . ► Desorption studies demonstrated that the sorbent–metal interaction is reversible. - Abstract: In this study, chemically modified radish cake, a by-product of biodiesel production, was used to remove Cd 2+ from aqueous solutions. The chemical modification was carried out by treating the radish cake with citric acid (CRC), NaOH (NRC) or the combination of citric acid and NaOH (CNRC). The sorbents were characterized by elemental analysis, surface area analysis, infrared spectroscopy (FTIR), potentiometric titration (PT), scanning electron microscopy–energy dispersive spectroscopy (SEM–EDS), and thermogravimetric analysis (TGA). The effect of the chemical treatment and contact time on cadmium sorption was evaluated. The equilibrium data were analyzed using Freundlich and Langmuir models. The maximum sorption capacity obtained by the Langmuir isotherm was 58.5 mg/g and 64.10 mg/g for the CRC, and CNRC sorbents, respectively. Complete desorption of Cd 2+ was achieved using 0.1 mol/L HNO 3 . The results obtained demonstrate that chemically modified radish cake has potential as a sorbent for Cd 2+ removal from aqueous solutions.

  1. Efficient removal of endosulfan from aqueous solution by UV-C/peroxides: A comparative study

    Energy Technology Data Exchange (ETDEWEB)

    Shah, Noor S. [Radiation Chemistry Laboratory, National Centre of Excellence in Physical Chemistry, University of Peshawar, Peshawar 25120 (Pakistan); Environmental Engineering and Science Program, University of Cincinnati, 705 Engineering Research Center, Cincinnati, OH 45221-0012 (United States); He, Xuexiang [Environmental Engineering and Science Program, University of Cincinnati, 705 Engineering Research Center, Cincinnati, OH 45221-0012 (United States); Khan, Hasan M. [Radiation Chemistry Laboratory, National Centre of Excellence in Physical Chemistry, University of Peshawar, Peshawar 25120 (Pakistan); Khan, Javed Ali [Radiation Chemistry Laboratory, National Centre of Excellence in Physical Chemistry, University of Peshawar, Peshawar 25120 (Pakistan); Environmental Engineering and Science Program, University of Cincinnati, 705 Engineering Research Center, Cincinnati, OH 45221-0012 (United States); O' Shea, Kevin E. [Department of Chemistry and Biochemistry, Florida International University, Miami, FL 33199 (United States); Boccelli, Dominic L. [Environmental Engineering and Science Program, University of Cincinnati, 705 Engineering Research Center, Cincinnati, OH 45221-0012 (United States); Dionysiou, Dionysios D., E-mail: dionysios.d.dionysiou@uc.edu [Environmental Engineering and Science Program, University of Cincinnati, 705 Engineering Research Center, Cincinnati, OH 45221-0012 (United States); Nireas-International Water Research Centre, University of Cyprus, 20537 Nicosia (Cyprus)

    2013-12-15

    Highlights: • Removal of endosulfan was studied by UV-C and UV-based advanced oxidation processes (AOPs). • Among UV/S{sub 2}O{sub 8}{sup 2−}, UV/HSO{sub 5}{sup −}, and UV/H{sub 2}O{sub 2}, endosulfan was removed the most efficiently by UV/S{sub 2}O{sub 8}{sup 2−}. • Hydroxyl and/or sulfate radicals were involved in the destruction of endosulfan and its by-products. • Presence of natural organic matter or alcohol inhibited the removal of endosulfan and its by-products. • Degradation pathways were proposed based on the nature of endosulfan degradation intermediates. -- Abstract: This study explored the efficiency of UV-C-based advanced oxidation processes (AOPs), i.e., UV/S{sub 2}O{sub 8}{sup 2−}, UV/HSO{sub 5}{sup −}, and UV/H{sub 2}O{sub 2} for the degradation of endosulfan, an organochlorine insecticide and an emerging water pollutant. A significant removal, 91%, 86%, and 64%, of endosulfan, at an initial concentration of 2.45 μM and UV fluence of 480 mJ/cm{sup 2}, was achieved by UV/S{sub 2}O{sub 8}{sup 2−}, UV/HSO{sub 5}{sup −}, and UV/H{sub 2}O{sub 2} processes, respectively, at a [peroxide]{sub 0}/[endosulfan]{sub 0} molar ratio of 20. The efficiency of these processes was, however, inhibited in the presence of radical scavengers, such as alcohols (e.g., tertiary butyl alcohol and isopropyl alcohol) and natural organic matter (NOM). The inhibition was also influenced by common inorganic anions in the order of nitrite > bicarbonate > chloride > nitrate ≃ sulfate. The observed pseudo-first-order rate constant decreased while the degradation rate increased with increasing initial concentration of the target contaminant. The degradation mechanism of endosulfan by the AOPs was evaluated revealing the main by-product as endosulfan ether. Results of this study suggest that UV-C-based AOPs are potential methods for the removal of pesticides, such as endosulfan and its by-products, from contaminated water.

  2. Removal of Pb2+ from aqueous solutions by a high-efficiency resin

    International Nuclear Information System (INIS)

    Guo, Hao; Ren, Yongzheng; Sun, Xueliang; Xu, Yadi; Li, Xuemei; Zhang, Tiancheng; Kang, Jianxiong; Liu, Dongqi

    2013-01-01

    The removal of Pb 2+ from aqueous solution by 732 cation-exchange resin in sodium type (732-CR) has been studied in batch experiments at varying pH (2.0–8.0), Pb 2+ concentration (50–200 mg/L), contact time (5–300 min), temperature (288–308 K) and resin dose (0.125–0.75 g/L). The experimental data show that the ion-exchange process was dependent on pH and temperature, the optimal exchange capacity was found at pH 4.0, and higher temperature was beneficial to lead sorption. Kinetic data indicate that the ion-exchange process followed a pseudo-first order model. The equilibrium exchange capacity could be reached at approximately 4 h, and the maximum sorption capacity of Pb 2+ at pH 4.0 was 396.8 mg/g resin. The equilibrium data were evaluated with Langmuir and Freundlich model, and were best fitted with Langmuir model. The thermodynamic parameters for removal of Pb 2+ indicate that the reaction was spontaneous and endothermic. Additionally, column tests were conducted by using both synthetic solution and effluents from lead battery industry. The regeneration of resin was performed for two sorption-regeneration cycles by 1 M NaOH, and the results show that effective regeneration was achieved by this method.

  3. Mercury nano-trap for effective and efficient removal of mercury(II) from aqueous solution

    Science.gov (United States)

    Li, Baiyan; Zhang, Yiming; Ma, Dingxuan; Shi, Zhan; Ma, Shengqian

    2014-11-01

    Highly effective and highly efficient decontamination of mercury from aqueous media remains a serious task for public health and ecosystem protection. Here we report that this task can be addressed by creating a mercury ‘nano-trap’ as illustrated by functionalizing a high surface area and robust porous organic polymer with a high density of strong mercury chelating groups. The resultant porous organic polymer-based mercury ‘nano-trap’ exhibits a record-high saturation mercury uptake capacity of over 1,000 mg g-1, and can effectively reduce the mercury(II) concentration from 10 p.p.m. to the extremely low level of smaller than 0.4 p.p.b. well below the acceptable limits in drinking water standards (2 p.p.b.), and can also efficiently remove >99.9% mercury(II) within a few minutes. Our work therefore presents a new benchmark for mercury adsorbent materials and provides a new perspective for removing mercury(II) and also other heavy metal ions from contaminated water for environmental remediation.

  4. Removal of lead from aqueous solution by an efficient low cost biosorbent

    Energy Technology Data Exchange (ETDEWEB)

    Alam, Sultan; Ullah, Azmat; Khan, Mashooq; Sadiq, Mohammad [Univ. of Malakand, Chakdara (Pakistan). Dept. of Chemistry; Hussain, Zahid; Amin, Noorul [AWK Univ., Mardan (Pakistan). Dept. of Chemistry

    2012-03-15

    Removal of Pb(II) ion from aqueous solution on modified sawdust obtained from Morus alba was investigated. The sample was characterized by BET surface area, EDX, FTIR and Zeta potential technique. The surface contains carbonyl and hydroxyl functional groups which act as binding sites for Pb(II) ion. Adsorption kinetics of Pb(II) on sawdust was tested by pseudo first order, Elovich and parabolic diffusion kinetic equations. The adsorption data were found to fit to Freundlich, Langmuir and Tempkin isotherms. The rate of adsorption was high at high temperature. Thermodynamic parameters like {delta}H, {delta}S and {delta}G were calculated from the kinetic data. The positive values of {delta}S reflect some structural exchange among the active site of the adsorbent and metal ion. The negative values of Gibbs free energy ({delta}G) show the spontaneous nature of the process. (orig.)

  5. Efficiency of manganese dioxide for the removal of antimony from aqueous solutions

    International Nuclear Information System (INIS)

    Hasany, S.M.; Najamuddin; Ikram, M.

    1993-01-01

    The sorption of antimony onto manganese dioxide from aqueous solution has been investigated as a function of shaking time, composition of electrolyte, concentration of sorbent and sorbate, Maximum sorption of antimony has been achieved from deionized water after 15 minutes shaking at 45 cm/sup 3/g/sup -1/ V/W ratio. The influence of different anions and cations on the sorption has also been examined. EDTA, tartrate, citrate and Fe(II) decreased the sorption significantly. Among the metal ions tested only Se (IV) has shown strong sorption than antimony whereas Co(II), Hf (IV) and Te(IV) indicated low sorption affinity under similar experimental conditions. The sorption of antimony was also tested by different isotherms. The data fitted only to Freyndlich and D-R models. The sorption capacity of 7.71 m mole g/sup -1/, mean energy of sorption of 8.9 kJ mole/sup -1/ and of B = 0.00632 mole/sup 2/kJ/sup -2/ have been system. It is concluded that manganese dioxide can be used for the removal of antimony from industrial effluents and for its recovery from very dilute solutions. The oxide can also be applied for the separation of antimony, selenium and arsenic from Te(IV). (author)

  6. Efficient adsorptive removal of Congo red from aqueous solution by synthesized zeolitic imidazolate framework-8

    Directory of Open Access Journals (Sweden)

    Canlan Jiang

    2016-10-01

    Full Text Available Dyes exposure in aquatic environment creates risks to human health and biota due to their intrinsic toxic mutagenic and carcinogenic characteristics. In this work, a metal-organic frameworks materials, zeolitic imidazolate framework-8 (ZIF-8, was synthesized through hydrothermal reaction for the adsorptive removal of harmful Congo red (CR from aqueous solution. Results showed that the maximum adsorption capacity of CR onto ZIF-8 was ultrahigh as 1250 mg g−1. Adsorption behaviors can be successfully fitted by the pseudo-second order kinetic model and the Langmuir isotherm equation. Solution conditions (pH condition and the co-exist anions may influent the adsorption behaviors. The adsorption performance at various temperatures indicated the process was a spontaneous and endothermic adsorption reaction. The enhanced adsorption capacity was determined due to large surface area of ZIF-8 and the strong interactions between surface groups of ZIF-8 and CR molecules including the electrostatic interaction between external active sites Zn−OH on ZIF-8 -and −SO3 or –N=N– sites in CR molecule, and the π–π interaction.

  7. Efficient removal of tetracycline with KOH-activated graphene from aqueous solution.

    Science.gov (United States)

    Ma, Jie; Sun, Yiran; Yu, Fei

    2017-11-01

    Activated graphene absorbents with high specific surface area (SSA) were prepared by an easy KOH-activated method, and were applied in absorbing antibiotics, such as tetracycline (TC). After activation, many micropores were introduced to graphene oxide sheets, leading to higher SSA and many new oxygen-containing functional groups, which gave KOH-activated graphene excellent adsorption capacity (approx. 532.59 mg g -1 ) of TC. Further study on the adsorption mechanism showed that the Langmuir isotherm model and the pseudo-second-order kinetic model fitted with experiment data. To further understand the adsorption process, the effects of solid-liquid ratio, pH, ionic strength and coexisting ions were also investigated. The results revealed that, compared with pH and ionic strength, solid-liquid ratio and coexisting ions (Cu 2+ , CrO 4 2- ) had more significant influence over the adsorption performance. The findings provide guidance for application of KOH-activated graphene as a promising alternative adsorbent for antibiotics removal from aqueous solutions.

  8. Efficient removal of uranium from aqueous solution by zero-valent iron nanoparticle and its graphene composite

    International Nuclear Information System (INIS)

    Li, Zi-Jie; Wang, Lin; Yuan, Li-Yong; Xiao, Cheng-Liang; Mei, Lei; Zheng, Li-Rong; Zhang, Jing; Yang, Ju-Hua; Zhao, Yu-Liang; Zhu, Zhen-Tai; Chai, Zhi-Fang; Shi, Wei-Qun

    2015-01-01

    Highlights: • Uranium removal by ZVI-nps: independent of pH, the presence of CO 3 2− , humic acid, or mimic groundwater constituents. • Rapid removal kinetics and sorption capacity of ZVI-nps is 8173 mg U/g. • Two reaction mechanisms: sufficient Fe 0 → reductive precipitation as U 3 O 7 ; insufficient Fe 0 → hydrolysis precipitation of U(VI). • Fe/graphene composites: improved kinetics and higher U(VI) reduction ratio. - Abstract: Zero-valent iron nanoparticle (ZVI-np) and its graphene composites were prepared and applied in the removal of uranium under anoxic conditions. It was found that solutions containing 24 ppm U(VI) could be completely cleaned up by ZVI-nps, regardless of the presence of NaHCO 3 , humic acid, mimic groundwater constituents or the change of solution pH from 5 to 9, manifesting the promising potential of this reactive material in permeable reactive barrier (PRB) to remediate uranium-contaminated groundwater. In the measurement of maximum sorption capacity, removal efficiency of uranium kept at 100% until C 0 (U) = 643 ppm, and the saturation sorption of 8173 mg U/g ZVI-nps was achieved at C 0 (U) = 714 ppm. In addition, reaction mechanisms were clarified based on the results of SEM, XRD, XANES, and chemical leaching in (NH 4 ) 2 CO 3 solution. Partially reductive precipitation of U(VI) as U 3 O 7 was prevalent when sufficient iron was available; nevertheless, hydrolysis precipitation of U(VI) on surface would be predominant as iron got insufficient, characterized by releases of Fe 2+ ions. The dissolution of Fe 0 cores was assigned to be the driving force of continuous formation of U(VI) (hydr)oxide. The incorporation of graphene supporting matrix was found to facilitate faster removal rate and higher U(VI) reduction ratio, thus benefitting the long-term immobilization of uranium in geochemical environment

  9. Survey Efficiency of Ultraviolet and Zinc Oxide Process (UV/ZnO for Removal of Diazinon Pesticide from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Mohammad Hadi Dehghani

    2015-03-01

    Full Text Available The presence of persistent organic pollutants and toxics (e.g., pesticides in ground, surface, and drinking water resources combined with the inability of conventional treatment methods to remove these pollutants have led to the development of advanced oxidation processes. Nowadays, nanophotocatalyst processes are considered as clean and environmentally-friendly treatment methods that can be extensively used for removing contaminants. The objective of the present study was to determine the efficiency of the ultraviolet and zinc oxide (UV/ZnO process in the removal of diazinon pesticide from aqueous solutions. For the purposes of this study, samples were adjusted in a batch reactor at five different detention times. The pH levels used were 3, 7, and 9. Irradiation was performed using a 125 W medium-pressure mercury lamp. The diazinon concentrations of the samples were 100 and 500 µg/L and the concentrations of zinc oxide nanoparticles were 50, 100, and 150 mg/L. The highest degradation efficiency was observed at pH 7 (mean = 80.92 30.3, while the lowest was observed for pH 3 (mean 67.11 24.49. Results showed that the optimal concentration of nanoparticles (6-12 nm was 100 mg L-1.

  10. Investigation of Acorn fruit Ash Efficiency in Cadmium Removal from Aqueous Solutions: Adsorption Isotherm and Kinetic Studies

    Directory of Open Access Journals (Sweden)

    Salman Zarei

    2014-12-01

    Full Text Available Background: Heavy metals are known as significant pollutants because of toxicity and nonbiodegradable characteristics. Cadmium is one of the heavy metals that have carcinogen potential. So, this study carried out in order to investigate the acorn fruit ash efficiency in cadmium removal from aqueous solutions. Methods: This study was done in the batch laboratory conditions. In this study, the effect of different parameters including pH, contact time, adsorbent dose, and initial cadmium concentration were evaluated. The Langmuir, Freundlich and Temkin isotherm models were used for analysis of the equilibrium isotherm. Adsorption kinetics of cadmium by different models were also investigated. The measurement of residual cadmium in the samples was determined by atomic absorption spectrophotometry at 228.8 nm. The SPSS-16 software was used for analysis of data. Results: According to the results, the maximum adsorption capacity of cadmium was 9.29 mg/g at pH=7 and 8 g/L adsorbent dose. The removal efficiency was increased with increasing contact time and decreased with increasing of cadmium initial concentration. Investigation of achieving data showed that the adsorption process followed better by Freundlich isotherm and the pseudo-second order kinetic. Conclusions: According to the results of this study, it could be concluded that the acorn fruit ash had high ability in cadmium adsorption and could be used as a cheap adsorbent in the removal of cadmium.

  11. High efficient removal of chromium (VI) using glycine doped polypyrrole adsorbent from aqueous solution

    CSIR Research Space (South Africa)

    Ballav, N

    2012-08-01

    Full Text Available Glycine doped polypyrrole (PPy-gly) adsorbent was prepared via in situ polymerization of pyrrole (Py) monomer in the presence of glycine (gly) for the removal of Cr(VI). Formation of PPy homopolymer and inclusion of gly in the PPy matrix were...

  12. Efficiency of Advanced H2O2/ZnO Oxidation Process in Ceftriaxone Antibiotic Removal from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Maryam Noroozi cholcheh

    2017-11-01

    Full Text Available A major concern about pharmaceutical pollution is the presence of antibiotics in water resources through their release into sewers where they cause bacterial resistance and enhanced drug-resistance in human-borne pathogens and growing microbial populations in the environment. The objective of this study was to investigate the efficiency of  the advanced H2O2/ZnO oxidation process in removing ceftriaxone from aqueous solutions. For this purpose, an experimental study was conducted in which the SEM, XRD, and TEM techniques were employed to determine the size of Zinc oxide nano-particles. Additionally, the oxidation process parameters of pH (3-11, molar ratio of H2O2/ZnO (1.5-3, initial concentration of ceftriaxone (5–15 mg/L, and contact time (30-90 min were investigated. Teh data thus obntained were subjected top statistical analysis using the SPSS (ANOVA test. XRD results revealeda hexagonal crystal structure for the nano-ZnO. TEM images confirmed the spherical shape of the nanoparticles. Finally, SEM images revealed that the Zn nanoparticles used in this study were less than 30 nanometers in diameter. Based on the results, an optimum pH of 11, a contact time of 90 minutes, and a H2O2/ZnO molar ratio equal to 1.5 were the optimum conditions to achieve a ceftriaxone removal efficiency of 92%. The advance H2O2/ZnO oxidation process may thus be claimed to be highly capable of removing ceftriaxone from aqueous solutions.

  13. Removal of heavy metals from aqueous solution by an efficient low cost biosorbent (abstract)

    International Nuclear Information System (INIS)

    Alam, S.; Ullah, A.

    2011-01-01

    The aim of this work was to assess the possibility of removing some heavy metals from water by a low-cost bio sorbent. Removal of lead and cadmium which differ in toxicity, as well as in some other characteristics were examined. Sawdust of Morus alba wood modified with 0.5N NaOH was applied as low cost bio sorbent. The sample was characterized by BET surface area, EDX, FTIR and Zeta potential technique. The removal of Cd(II) and Pb(II) by treated sawdust has been found to be concentration, contact time, adsorbate dose and temperature dependent. The adsorption parameters were determined using Freundlich, Langmuir and Tempkin isotherm models. The applicability of kinetic models i.e. pseudo first order, Elovich and parabolic diffusion has also been investigated. Thermodynamic parameters like delta H, delta S and delta G were calculated from the kinetic data. The equilibrium adsorption was achieved in 100 min. The result shows that the adsorbent examined was found to have good adsorption capacity. Surface complexation and ion exchange are the major removal mechanisms involved. The correlation coefficient for Langmuir, Freundlich and Tempkin equation were well fitted. The adsorption follows first-order kinetics. The rate of adsorption was high at high temperature. The positive values of delta S reflect some structural exchange among the active site of the adsorbent and metal ion. The negative value of Gibbs free energy (delta G) shows the spontaneous nature of the process. The findings of the data reveal that the modified Sawdust is a low-cost, easily available bio sorbent and can be use as alternative to other commercial adsorbents as well as for effluent treatment in industries. (author)

  14. Efficient removal of cobalt from aqueous solution by zinc oxide nanoparticles. Kinetic and thermodynamic studies

    Energy Technology Data Exchange (ETDEWEB)

    Khezami, L.; Modwi, A. [Al Imam Mohammad Ibn Saud Islamic Univ. (IMSIU), Riyadh (Saudi Arabia). Dept. of Chemistry; Taha, Kamal K. [Al Imam Mohammad Ibn Saud Islamic Univ. (IMSIU), Riyadh (Saudi Arabia). Dept. of Chemistry; Univ. of Bahri, Khartoum (Sudan). College of Applied and Industrial Sciences

    2017-08-01

    This article deals with the removal of cobalt ions using zinc oxide nanopowder. The nanomaterial was prepared via the sol-gel method under supercritical drying. The nanomaterial was characterised via XRD, SEM, EDX, FTIR, and BET surface area techniques. The kinetics, equilibrium, and thermodynamic studies of the metal ions adsorption on the nanomaterial were conducted in batch mode experiments by varying some parameters such as pH, contact time, initial ion concentrations, nanoparticles dose, and temperature. The data revealed significant dependence of the adsorption process on concentration, and the temperature was found to enhance the adsorption rate indicating an endothermic nature of the adsorption. The adsorption complied well with the pseudo-second-order kinetics model. The adsorption process was found to match the Langmuir adsorption isotherm. The ZnO nanoparticles could successfully remove up to 125 mg.g{sup -1} of Co(II) ions at elevated temperature. The metal ions adsorption could be described as an endothermic, spontaneous physisorption process. A mechanism for the metal ions adsorption was proposed.

  15. Efficient removal of cobalt from aqueous solution by zinc oxide nanoparticles. Kinetic and thermodynamic studies

    International Nuclear Information System (INIS)

    Khezami, L.; Modwi, A.; Taha, Kamal K.; Univ. of Bahri, Khartoum

    2017-01-01

    This article deals with the removal of cobalt ions using zinc oxide nanopowder. The nanomaterial was prepared via the sol-gel method under supercritical drying. The nanomaterial was characterised via XRD, SEM, EDX, FTIR, and BET surface area techniques. The kinetics, equilibrium, and thermodynamic studies of the metal ions adsorption on the nanomaterial were conducted in batch mode experiments by varying some parameters such as pH, contact time, initial ion concentrations, nanoparticles dose, and temperature. The data revealed significant dependence of the adsorption process on concentration, and the temperature was found to enhance the adsorption rate indicating an endothermic nature of the adsorption. The adsorption complied well with the pseudo-second-order kinetics model. The adsorption process was found to match the Langmuir adsorption isotherm. The ZnO nanoparticles could successfully remove up to 125 mg.g -1 of Co(II) ions at elevated temperature. The metal ions adsorption could be described as an endothermic, spontaneous physisorption process. A mechanism for the metal ions adsorption was proposed.

  16. Microalgal-biochar immobilized complex: A novel efficient biosorbent for cadmium removal from aqueous solution.

    Science.gov (United States)

    Shen, Ying; Li, Huan; Zhu, Wenzhe; Ho, Shih-Hsin; Yuan, Wenqiao; Chen, Jianfeng; Xie, Youping

    2017-11-01

    The feasibility of the bioremediation of cadmium (Cd) using microalgal-biochar immobilized complex (MBIC) was investigated. Major operating parameters (e.g., pH, biosorbent dosage, initial Cd(II) concentration and microalgal-biochar ratio) were varied to compare the treatability of viable algae (Chlorella sp.), biochar and MBIC. The biosorption isotherms obtained by using algae or biochar were found to have satisfactory Langmuir predictions, while the best fitting adsorption isotherm model for MBIC was the Sips model. The maximum Cd(II) adsorption capacity of MBIC with a Chlorella sp.: biochar ratio of 2:3 (217.41mgg -1 ) was higher than that of Chlorella sp. (169.92mgg -1 ) or biochar (95.82mgg -1 ) alone. The pseudo-second-order model fitted the biosorption process of MBIC well (R 2 >0.999). Moreover, zeta potential, SEM and FTIR studies revealed that electrostatic attraction, ion exchange and surface complexation were the main mechanisms responsible for Cd removal when using MBIC. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Ordered Mesoporous Carbons as Novel and Efficient Adsorbent for Dye Removal from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Phuong T. Dang

    2016-01-01

    Full Text Available Ordered mesoporous carbons (OMCs were successfully synthesized by using hard template and soft template methods. These materials were characterized by XRD, TEM, and N2 adsorption-desorption Brunauer-Emmett-Teller (BET. From the obtained results, it is revealed that the obtained OMCs samples showed high surface area (>1000 m2/g with high pore volume, mainly mesopore volume (1.2–2.4 cm3/g. Moreover, OMCs samples had similar structure of the SBA-15 silica and exhibited high MB adsorption capacity with qm of 398 mg·g−1 for OMCs synthesis with hard template and 476 mg·g−1 for OMCs synthesis with soft template, respectively. From kinetics investigation, it is confirmed that MB adsorption from aqueous solution obeys the pseudo-second-order kinetic equation.

  18. Studies on efficiency of guava (Psidium guajava) bark as bioadsorbent for removal of Hg (II) from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Lohani, Minaxi B. [Integral University, Kursi Road, Lucknow 226026, UP (India)], E-mail: minaxi_lohani@sify.com; Singh, Amarika; Rupainwar, D.C. [Institute of Engineering and Technology Sitapur Road, Lucknow 226021, UP (India); Dhar, D.N. [IIT Kanpur (India)

    2008-11-30

    Biosorption of Hg (II) was investigated in this study by using guava bark powder (GBP). In the batch system, effects of various parameters like contact time, initial concentration, pH and temperature were investigated. Removal of Hg (II) was pH dependent and was found maximum at pH 9.0. Based on this study, the thermodynamic parameters like change in standard Gibb's free energy ({delta}G{sup 0}), standard enthalpy ({delta}H{sup 0}) and standard entropy ({delta}S{sup 0}) were evaluated. The rate kinetic study was found to follow second-order. The applicability of Freundlich adsorption isotherm model was tested. The value of regression coefficient was greater than 0.99. This indicated that the isotherm model adequately described the experimental data of the biosorption of Hg (II). Maximum adsorption of 3.364 mg g{sup -1} was reached at 80 min. The results of the study showed that guava bark powder can be efficiently used as a low-cost alternative for the removal of divalent mercury from aqueous solutions.

  19. Studies on efficiency of guava (Psidium guajava) bark as bioadsorbent for removal of Hg (II) from aqueous solutions

    International Nuclear Information System (INIS)

    Lohani, Minaxi B.; Singh, Amarika; Rupainwar, D.C.; Dhar, D.N.

    2008-01-01

    Biosorption of Hg (II) was investigated in this study by using guava bark powder (GBP). In the batch system, effects of various parameters like contact time, initial concentration, pH and temperature were investigated. Removal of Hg (II) was pH dependent and was found maximum at pH 9.0. Based on this study, the thermodynamic parameters like change in standard Gibb's free energy (ΔG 0 ), standard enthalpy (ΔH 0 ) and standard entropy (ΔS 0 ) were evaluated. The rate kinetic study was found to follow second-order. The applicability of Freundlich adsorption isotherm model was tested. The value of regression coefficient was greater than 0.99. This indicated that the isotherm model adequately described the experimental data of the biosorption of Hg (II). Maximum adsorption of 3.364 mg g -1 was reached at 80 min. The results of the study showed that guava bark powder can be efficiently used as a low-cost alternative for the removal of divalent mercury from aqueous solutions

  20. Efficiency and mechanisms of Cd removal from aqueous solution by biochar derived from water hyacinth (Eichornia crassipes).

    Science.gov (United States)

    Zhang, Feng; Wang, Xin; Yin, Daixia; Peng, Bo; Tan, Changyin; Liu, Yunguo; Tan, Xiaofei; Wu, Shixue

    2015-04-15

    This study investigated the efficiency and mechanisms of Cd removal by biochar pyrolyzed from water hyacinth (BC) at 250-550 °C. BC450 out-performed the other BCs at varying Cd concentrations and can remove nearly 100% Cd from aqueous solution within 1 h at initial Cd ≤ 50 mg l(-1). The process of Cd sorption by BC450 followed the pseudo-second order kinetics with the equilibrium being achieved after 24 h with initial Cd ranging from 100 to 500 mg l(-1). The maximum Cd sorption capacity of BC450 was estimated to be 70.3 mg g(-1) based on Langmuir model, which is prominent among a range of low-cost sorbents. Based on the balance analysis between cations released and Cd sorbed onto BC450 in combination with SEM-EDX and XPS data, ion-exchange followed by surface complexation is proposed as the dominant mechanism responsible for Cd immobilization by BC450. In parallel, XRD analysis also suggested the formation of insoluble Cd minerals (CdCO3, Cd3P2, Cd3(PO4)2 and K4CdCl6) from either (co)-precipitation or ion exchange. Results from this study highlighted that the conversion of water hyacinth into biochar is a promising method to achieve effective Cd immobilization and improved management of this highly problematic invasive species. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Synthesis of Ce(III)-doped Fe3O4 magnetic particles for efficient removal of antimony from aqueous solution

    International Nuclear Information System (INIS)

    Qi, Zenglu; Joshi, Tista Prasai; Liu, Ruiping; Liu, Huijuan; Qu, Jiuhui

    2017-01-01

    Highlights: • Doping of Ce into Fe 3 O 4 was achieved based on a facile solvothermal method. • After doping, the removal capacity was increased by 5 times for “Sb(V)” and 2 times for “Sb(III)”. • Decreasing pH improved adsorption of Sb(V) but decreased adsorption of Sb(III). • Antimony sorption mechanisms on Ce-doped Fe 3 O 4 were illustrated. - Abstract: Aqueous antimony (Sb) pollution from human activity is of great concern in drinking water due to its adverse health effect. Magnetic Fe 3 O 4 particles, with high separation ability from solution, have been considered as a low-cost Sb adsorbent for contaminants. However, the limited adsorption capacity has restricted its practical application. In this study, a solvothermal approach was developed for doping Ce(III) into Fe 3 O 4 , thereby increasing the adsorption efficacy for both Sb(III) and Sb(V). In contrast to un-doped Fe 3 O 4 , the adsorption capacity towards Sb(III) and Sb(V) in Ce-doped materials increased from 111.4 to 224.2 mg/g and from 37.2 to 188.1 mg/g at neutral pH, respectively. Based on the combined results of XPS, XRD, and FTIR, it confirmed that Ce atom successfully doped into the Fe 3 O 4 structure, resulting in the decreased particle size, increased the surface area, and isoelectric point. Furthermore, the vibrating sample magnetometer (VSM) results showed that the Ce doping process had some side effects on the primitive magnetic property, but remaining the high separation potential during water treatment. According to the high removal efficiency and magnetic property, the Ce-doped Fe 3 O 4 of great simplicity should be a promising adsorbent for aqueous Sb removal.

  2. Highly efficient removal of chlorotetracycline from aqueous solution using graphene oxide/TiO2 composite: Properties and mechanism

    Science.gov (United States)

    Li, Zhaoqian; Qi, Mengyu; Tu, Chunyan; Wang, Weiping; Chen, Jianrong; Wang, Ai-Jun

    2017-12-01

    The extensive usage of chlorotetracycline (CTC) has caused the persistence of antibiotic residues in aquatic environments, resulting in serious threat to human health and ecosystems. In this study, graphene oxide/titanium dioxide (GO/TiO2) nanocomposite was successfully synthesized via in situ hydrolysis of tetra-n-butyl titanate (Ti(BuO)4) to TiO2 particles on GO sheets and used as adsorbent for efficient adsorptive removal of CTC from aqueous solution. The prepared GO/TiO2 was characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transformed infrared (FT-IR), Raman spectroscopy and X-ray photoelectron (XPS). Adsorption kinetics, isotherms and thermodynamics were systematically investigated to evaluate the adsorption properties of GO/TiO2. Adsorption mechanism was further analyzed by FT-IR, UV-vis and XPS. The results indicated that adsorption kinetics closely followed the pseudo-second order model; the maximum adsorption capacity determined by Langmuir model was 261.10 mg g-1 at 298 K and the thermodynamic studies revealed that the adsorption of CTC onto the GO/TiO2 was a spontaneous and endothermic process. Moreover, the interactions between CTC and GO/TiO2 were presumed to be ligand exchange between CTC and TiO2, while the π-π electron donor-acceptor interaction, hydrogen bond and cation-π bonding were constructed between CTC and GO. Finally, the prepared GO/TiO2 was successfully applied for the efficient removal of CTC from Wu River water.

  3. Highly efficient removal of perfluorooctanoic acid from aqueous solution by H2O2-enhanced electrocoagulation-electroflotation technique

    Directory of Open Access Journals (Sweden)

    Bo Yang

    2016-03-01

    Full Text Available Electrocoagulation (EC technique was used to investigate the removal performance of aqueous perfluorooctanoic acid (PFOA with relatively high concentration as simulating the wastewater from organic fluorine industry. A comparison was done with the similar amount of coagulant between EC and chemical coagulation process. PFOA removal obtained was higher with EC process, especially for Fe anode. Several factors were studied to optimize the EC process. At the optimal operating parameters including 37.5 mA/cm2 of current density, initial pH 3.77, and 180 rpm of mixing speed, 93% of PFOA could be removed with 100 mg/L of initial concentration after 90-min electrolysis. Furthermore, the remove efficiency could be obviously improved by H2O2 intermittent addition, which removed more than 99% of PFOA within 40-min EC. It could be attributed to that H2O2 facilitated the oxidative transformation from ferrous to ferric ion. In addition, the adsorptive removal of aqueous PFOA on Fe flocs during EC was also verified by fourier transform infrared spectra.

  4. Efficient device for the benign removal of organic pollutants from aqueous solutions using modified mesoporous magnetite nanostructures

    Science.gov (United States)

    Vojoudi, H.; Badiei, A.; Amiri, A.; Banaei, A.; Ziarani, G. M.; Schenk-Joß, K.

    2018-02-01

    In this study, a home-made device comprising a column filled with magnetic mesoporous silica-coated nanostructures (MSCM-PA) as an adsorbent was constructed and used to remove organic pollutants from aqueous solutions. The MSCM-PA adsorbent was prepared and characterized using Fourier transform-infrared spectroscopy, ultraviolet-visible spectroscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, vibrating sample magnetometry, Brunauer-Emmett-Teller, thermogravimetric analysis/differential thermal analysis, and powder X-ray diffraction techniques. The adsorption behavior of the MSCM-PA sorbent was studied based on the removal of Everzol blue dye from aqueous solutions. We investigated the effects of various parameters such as the solution pH, initial dye concentration, adsorbent dose, flow rate, and contact time on the adsorption of Everzol blue from aqueous solutions. The adsorption data were modeled using Langmuir and Freundlich isotherms, and a good fit was obtained with the Langmuir isotherm. The maximum Everzol blue adsorption capacity by MSCM-PA was 162 mg g-1. The results indicate that our device is capable of adsorbing anionic dyes from aqueous solutions.

  5. Efficiency of Chitosan for the Removal of Pb (II, Fe (II and Cu (II Ions from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Soheil Sobhanardakani

    2014-09-01

    Full Text Available Background: Heavy metals have been recognized as harmful environmental pollutant known to produce highly toxic effects on different organs and systems of both humans and animals. The aim of this paper is to evaluate the adsorption potential of chitosan for the removal of Pb(II, Fe(II and Cu(II ions from aqueous solutions. Methods: This study was conducted in laboratory scale. In this paper chitosan has been used as an adsorbent for the removal of Pb(II, Fe(II and Cu(II from aqueous solution. In batch tests, the effects of parameters like pH solution (1.0-8.0, initial metal concentrations (100-1000 mgL-1, contact time (5.0-150 min and adsorbent dose (1.0-7.0 g on the adsorption process were studied. Results: The results showed that the adsorption of Pb(II, Fe(II and Cu(II ions on chitosan strongly depends on pH. The experimental isothermal data were analyzed using the Langmuir and Freundlich equations and it was found that the removal process followed the Langmuir isotherm and maximum adsorption capacity for the adsorption of Pb(II, Fe(II and Cu(II ions by the chitosan were 55.5mg g−1, 71.4 mg g−1 and 59 mg g−1, respectively, under equilibrium conditions at 25±1 ºC. The adsorption process was found to be well described by the pseudo-second-order rate model. Conclusion: The obtained results showed that chitosan is a readily, available, economic adsorbent and was found suitable for removing Pb(II, Fe(II and Cu(II ions from aqueous solution.

  6. Comparison of the Efficiency of Simultaneous Application of UV/O3 for the Removal of Organophosphorus and Carbamat Pesticides in Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Mohammad Taghi Samadi

    2010-03-01

    Full Text Available A vast variety of pesticides are used for agricultural pests in Iran. The release of these persistent organic pollutants. into water supplies leaves adverse effects on both the environment and public health. Advanced oxidation processes have been used recently for pesticide removal. In this research, the combined UV/O3 process has been investigated for the removal of organophosphorus pesticides (Diazinon, Chlorpyrifos, Carbamate pesticides (carbaryl. In this survey, samples have been prepared by adding given concentration (1, 5, 10, 15, 20 mg/L of the pesticides to deionized water. The samples at separation periods were exposed to the combined UV/O3 (UV=50-200 Wm-2 and O3 = 1g hr-1in a bath  reactor at different pH levels (6, 7, 9 and for different contact times (0.5,1,1.5,2 hr and the removal efficiencies were determined. Residual concentrations were determined using GC/MS/MS and HPLC.  Based on the results, increasing pH reduced pesticide concentration and increased contact time had a direct effect on enhancing removal efficiency. The combined UV/O3 process was found to have a high efficiency (>80% in degrading both halogenated Organophosphorus(Chlorpyrifos and non- halogenated Organophosphorus (Diazinon pesticides. Its removal efficiency for degrading carbamate pesticide (Carbari was found to be >90%. Based on our results, this method may be suggested for the removal of pesticides from aqueous solutions.

  7. Efficient removal of perfluorooctane sulfonate from aqueous film-forming foam solution by aeration-foam collection.

    Science.gov (United States)

    Meng, Pingping; Deng, Shubo; Maimaiti, Ayiguli; Wang, Bin; Huang, Jun; Wang, Yujue; Cousins, Ian T; Yu, Gang

    2018-07-01

    Aqueous film-forming foams (AFFFs) used in fire-fighting are one of the main contamination sources of perfluorooctane sulfonate (PFOS) to the subterranean environment, requiring high costs for remediation. In this study, a method that combined aeration and foam collection was presented to remove PFOS from a commercially available AFFF solution. The method utilized the strong surfactant properties of PFOS that cause it to be highly enriched at air-water interfaces. With an aeration flow rate of 75 mL/min, PFOS removal percent reached 96% after 2 h, and the PFOS concentration in the collected foam was up to 6.5 mmol/L, beneficial for PFOS recovery and reuse. Increasing the aeration flow rate, ionic strength and concentration of co-existing surfactant, as well as decreasing the initial PFOS concentration, increased the removal percents of PFOS by increasing the foam volume, but reduced the enrichment of PFOS in the foams. With the assistance of a co-existing hydrocarbon surfactant, PFOS removal percent was above 99.9% after aeration-foam collection for 2 h and the enrichment factor exceeded 8400. Aeration-foam collection was less effective for short-chain perfluoroalkyl substances due to their relatively lower surface activity. Aeration-foam collection was found to be effective for the removal of high concentrations of PFOS from AFFF-contaminated wastewater, and the concentrated PFOS in the collected foam can be reused. Copyright © 2018 Elsevier Ltd. All rights reserved.

  8. The efficiency of biosynthesis silica nanoparticles at removal of heavy metals Cr and Cu from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Mohammad Hossein Sayadi

    2017-05-01

    Full Text Available Background and Aim: Nanotechnology considered as one of the main management strategy in reducing negative effects of water pollution, which leads to treating of water inexpensive and more effective. This study aimed to investigate the removal of Cr and Cu from aqueous solutions using nano-silicate which is synthesized by rice husk. Materials and Methods: In the present study, functionalized nano-silica with rice husk was fabricated and characterized by FT-IR، TEM, SEM and XRD. The effect of adsorbent dosage, initial concentration and equilibrium of chromium and copper and contact time in removal of mentioned heavy metals were investigated. Finally, the adsorption isotherms were analyzed. Results: The silica nanoparticles had nearly spherical morphology with a uniform size of about 80 nm. However, the obtained functionalized silica nanoparticles were spherical (about 90 nm in diameter. Results showed that optimum adsorption of Cr and Cu contaminant obtained at 100 minutes, while the optimum amount of adsorbent for Cr and Cu were 125 and 100 mg respectively. The optimal concentration of Cr and Cu was 2 mg/l. The correlation coefficients of adsorption isotherms of Cr (R2Langmuir =0.9946 and Cu (R2Langmuir =0.999 showed the good agreement between the adsorption data and Langmuir model. Conclusion: The study showed that the silica nanoparticles can be produced using agricultural waste as a inexpensive and environmentally friendly method and can be used to removing of contaminants from the aquatic environment.

  9. Efficient removal of Cd{sup 2+} from aqueous solutions using by-product of biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Rita F.L., E-mail: ritaflavia@gmail.com [Departamento de Quimica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil); Soares, Vitor C., E-mail: vcelios@gmail.com [Departamento de Quimica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil); Costa, Leticia M., E-mail: leticia@qui.ufmg.br [Departamento de Quimica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil); Nascentes, Clesia C., E-mail: clesia@qui.ufmg.br [Departamento de Quimica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil)

    2012-10-30

    Highlights: Black-Right-Pointing-Pointer Sorbents were prepared from radish cake, a waste from biodiesel production. Black-Right-Pointing-Pointer The chemical treatments used were simple, low-cost and enhanced the Cd{sup 2+} sorption. Black-Right-Pointing-Pointer The cadmium sorption process was evaluated by Freundlich and Langmuir models. Black-Right-Pointing-Pointer Chemically treated radish cake is an excellent alternative for removal of Cd{sup 2+}. Black-Right-Pointing-Pointer Desorption studies demonstrated that the sorbent-metal interaction is reversible. - Abstract: In this study, chemically modified radish cake, a by-product of biodiesel production, was used to remove Cd{sup 2+} from aqueous solutions. The chemical modification was carried out by treating the radish cake with citric acid (CRC), NaOH (NRC) or the combination of citric acid and NaOH (CNRC). The sorbents were characterized by elemental analysis, surface area analysis, infrared spectroscopy (FTIR), potentiometric titration (PT), scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), and thermogravimetric analysis (TGA). The effect of the chemical treatment and contact time on cadmium sorption was evaluated. The equilibrium data were analyzed using Freundlich and Langmuir models. The maximum sorption capacity obtained by the Langmuir isotherm was 58.5 mg/g and 64.10 mg/g for the CRC, and CNRC sorbents, respectively. Complete desorption of Cd{sup 2+} was achieved using 0.1 mol/L HNO{sub 3}. The results obtained demonstrate that chemically modified radish cake has potential as a sorbent for Cd{sup 2+} removal from aqueous solutions.

  10. Fabrication of Chitosan-complexed Electrode and Evaluation of Its Efficiency in Removal of Copper Ion from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Yoon Young-Chan

    2016-01-01

    Full Text Available In this study, we fabricated chitosan/PVA/activated carbon complexed electrode to remove copper ion from aqueous solution. The prepared composite electrode was analyzed by BET and SEM to investigate its physicochemical properties. Electrochemical properties of prepared composite electrodes were analyzed via cyclic voltammetry. Adsorption performance of copper ion on chitosan composite complexed electrodes was evaluated. Almost similar pore size distribution results were observed in the series of ACP not included electrodes while observed differences in pore size distribution for the ACP included one. Cyclic voltammetry results exhibited that oxidation-reduction reaction does not occur in a potential range of -1.0 ~ 1.0 V. The amount of copper ion during adsroption reaction is increase according to increase of adsorption potential to 1.0 V.

  11. Use of Raman spectroscopy to assess the efficiency of MgAl mixed oxides in removing cyanide from aqueous solutions

    International Nuclear Information System (INIS)

    Cosano, Daniel; Esquinas, Carlos; Jiménez-Sanchidrián, César; Ruiz, José Rafael

    2016-01-01

    Graphical abstract: - Highlights: • Raman is used by first time for adsorption of cyanide on calcined LDHs. • Raman is an effective, accurate and expeditious method for monitoring this process. • Cyanide is adsorbed by a rehydration process based on the “memory effect”. • The metal ratio of the LDH has a crucial influence on the adsorption capacity. - Abstract: Calcining magnesium/aluminium layered double hydroxides (Mg/Al LDHs) at 450 °C provides excellent sorbents for removing cyanide from aqueous solutions. The process is based on the “memory effect” of LDHs; thus, rehydrating a calcined LDH in an aqueous solution restores its initial structure. The process, which conforms to a first-order kinetics, was examined by Raman spectroscopy. The metal ratio of the LDH was found to have a crucial influence on the adsorption capacity of the resulting mixed oxide. In this work, Raman spectroscopy was for the first time use to monitor the adsorption process. Based on the results, this technique is an effective, expeditious choice for the intended purpose and affords in situ monitoring of the adsorption process. The target solids were characterized by using various instrumental techniques including X-ray diffraction spectroscopy, which confirmed the layered structure of the LDHs and the periclase-like structure of the mixed oxides obtained by calcination.

  12. Use of Raman spectroscopy to assess the efficiency of MgAl mixed oxides in removing cyanide from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Cosano, Daniel; Esquinas, Carlos; Jiménez-Sanchidrián, César; Ruiz, José Rafael, E-mail: qo1ruarj@uco.es

    2016-02-28

    Graphical abstract: - Highlights: • Raman is used by first time for adsorption of cyanide on calcined LDHs. • Raman is an effective, accurate and expeditious method for monitoring this process. • Cyanide is adsorbed by a rehydration process based on the “memory effect”. • The metal ratio of the LDH has a crucial influence on the adsorption capacity. - Abstract: Calcining magnesium/aluminium layered double hydroxides (Mg/Al LDHs) at 450 °C provides excellent sorbents for removing cyanide from aqueous solutions. The process is based on the “memory effect” of LDHs; thus, rehydrating a calcined LDH in an aqueous solution restores its initial structure. The process, which conforms to a first-order kinetics, was examined by Raman spectroscopy. The metal ratio of the LDH was found to have a crucial influence on the adsorption capacity of the resulting mixed oxide. In this work, Raman spectroscopy was for the first time use to monitor the adsorption process. Based on the results, this technique is an effective, expeditious choice for the intended purpose and affords in situ monitoring of the adsorption process. The target solids were characterized by using various instrumental techniques including X-ray diffraction spectroscopy, which confirmed the layered structure of the LDHs and the periclase-like structure of the mixed oxides obtained by calcination.

  13. A new nano-sorbent for fast and efficient removal of heavy metals from aqueous solutions based on modification of magnetic mesoporous silica nanospheres

    Science.gov (United States)

    Vojoudi, Hossein; Badiei, Alireza; Bahar, Shahriyar; Mohammadi Ziarani, Ghodsi; Faridbod, Farnoush; Ganjali, Mohammad Reza

    2017-11-01

    In the present study, a new and efficient nanosorbent for the fast removal of heavy metal ions was prepared. The proposed nanosorbent was fabricated using Fe3O4 magnetic core shelled by mesoporous silica, and cetyltrimethylammonium bromide (CTAB) as surfactant template through a sol-gel process. The magnetic nanomaterial was further modified with bis(3-triethoxysilylpropyl)tetrasulfide (MSCMNPs-S4). The final nanosphers were characterized by FT-IR, XRD, TGA, BET, SEM, TEM, DLS, VSM, EDX, and UV-Vis. The potential of the resultant mesoporous magnetite nanomaterials was investigated as a convenient and effective adsorbent for the removal of toxic heavy metal ions from aqueous solutions in a batch system. The effect of essential parameters on the removal efficiency including initial pH of sample solution, adsorbent amount, metal ion concentration, contact time and type and quantity of the eluent on the adsorption characteristics of the MSCMNPs-S4 were studied. Under the optimized conditions, the proposed nanosorbent exhibited high adsorption capacity of 303.03, 256.41 and 270.27 mg g-1 and maximum removal percentages of 98.8%, 96.4%, 95.7% for Hg(II), Pd(II) and Pb(II) ions, respectively. The mechanism of the adsorbtion was found to be in good agreement with the Langmuir isotherm model. Furthermore, the reusability investigation indicated that the MSCMNPs-S4 could be used frequently at least for five cycles without any significant loss in its performance.

  14. Da-KGM based GO-reinforced FMBO-loaded aerogels for efficient arsenic removal in aqueous solution.

    Science.gov (United States)

    Ye, Shuxin; Jin, Weiping; Huang, Qing; Hu, Ying; Li, Yan; Li, Jing; Li, Bin

    2017-01-01

    Composites based on deacetylated konjac glucomannan (Da-KGM) and graphene oxide (GO) aerogels with iron and manganese oxides (FMBO) for effective removal of arsenic from contaminated water. Da-KGM, which was used as supporting composite matrix here, were firstly treated with GO and loaded FMBO. The obtained Da-KGM/GO/FMBO composite aerogels were characterized by compression test, thermo gravimetric analysis (TGA), X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). The characteristic results showed that addition of GO exhibited enhanced mechanical properties towards Da-KGM aerogels. What's more, results of FTIR indicated the strong intermolecular hydrogen bond interaction between KGM and GO. Batch adsorption tests were used to evaluate arsenic removal capacity. Da-KGM/GO loaded FMBO composite aerogels exhibited high adsorption ability for arsenite [As(III)] and arsenate [As(V)]. The adsorption results showed that the arsenic for both arsenite [As(III)] and arsenate [As(V)] removal process followed a pseudo-second-order rate equation and Langmuir monolayer adsorption. The maximum As(III) and As(V) uptake capacity of Da-KGM/GO(10%)/FMBO composite aerogels reached 30.21mgg -1 and 12.08mgg -1 respectively according to Langmuir isotherm at pH 7 and 323K. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. A Ti-doped γ-Fe2O3/SDS nano-photocatalyst as an efficient adsorbent for removal of methylene blue from aqueous solutions.

    Science.gov (United States)

    Mirbagheri, Naghmeh Sadat; Sabbaghi, Samad

    2018-05-01

    Synthetic dyes are among the most important environmental pollutants in wastewaters. Consequently, elimination of the synthetic dyes from wastewaters using non-toxic materials and eco-friendly technologies has been of considerable interests. In this study, magnetically separable Ti-doped γ-Fe 2 O 3 photocatalysts were synthesized for the removal of methylene blue (MB) from a dye-contaminated aqueous solution (as a model of dye-polluted wastewaters). Compared to the pristine γ-Fe 2 O 3 , the 1.78 v% Ti-doped γ-Fe 2 O 3 significantly increased the adsorption of MB by 57% in the dark condition as a result of the improved BET surface area in this photocatalyst. Moreover, the contact time required for the photocatalytic degradation of MB by the 1.78 v% Ti-doped γ-Fe 2 O 3 decreased due to the higher concentration of charge carriers in this photocatalyst than that of the pristine γ-Fe 2 O 3 . The effect of different experimental parameters on the adsorption property and photocatalytic activity of the 1.78 v% Ti-doped γ-Fe 2 O 3 photocatalyst showed that the solution pH had a remarkable influence on the removal performance of this photocatalyst. Surface treatment of the 1.78 v% Ti-doped γ-Fe 2 O 3 with sodium dodecyl sulfate (SDS) resulted in the formation of a negatively charged Ti-doped γ-Fe 2 O 3 /SDS photocatalyst, which showed a higher tendency for the adsorption and removal of MB than the untreated photocatalyst. Moreover, the MB removal efficiency of this photocatalyst was among the best performances that have been reported for the γ-Fe 2 O 3 -based photocatalysts. The synthesized photocatalysts were characterized by various techniques, and a plausible mechanism for the removal of MB from aqueous solutions by the Ti-doped γ-Fe 2 O 3 /SDS photocatalyst was purposed. Copyright © 2018 Elsevier Ltd. All rights reserved.

  16. Preparation of low cost activated carbon from Myrtus communis and pomegranate and their efficient application for removal of Congo red from aqueous solution

    Science.gov (United States)

    Ghaedi, Mehrorang; Tavallali, Hossein; Sharifi, Mahdi; Kokhdan, Syamak Nasiri; Asghari, Alireza

    2012-02-01

    In this research, the potential applicability of activated carbon prepared from Myrtus communis (AC-MC) and pomegranate (AC-PG) as useful adsorbents for the removal of Congo red (CR) from aqueous solutions in batch method was investigated. The effects of pH, contact time, agitation time and amount of adsorbents on removal percentage of Congo red on both adsorbents were examined. Increase in pH up to 6 for AC-MC and pH 7 for AC-PG increase the adsorption percentage (capacity) and reach equilibrium within 30 min of contact time. Fitting the experimental data to conventional isotherm models like Freundlich, Langmuir, Tempkin and Dubinin-Radushkevich show that the experimental data fitted very well to the Freundlich isotherm for AC-MC and Langmuir isotherm for AC-PG. Fitting the experimental data to different kinetic models such as pseudo first-order, pseudo second-order, Elovich and intraparticle diffusion mechanism showed the applicability of a pseudo second-order with involvement of intraparticle diffusion model for interpretation of experimental data for both adsorbents. The adsorption capacity of AC-PG and AC-MC for the removal of CR was found to be 19.231 and 10 mg g -1. These results clearly indicate the efficiency of adsorbents as a low cost adsorbent for treatment of wastewater containing CR.

  17. pH variation and influence in an autotrophic nitrogen removing biofilm system using an efficient numerical solution strategy

    DEFF Research Database (Denmark)

    Vangsgaard, Anna Katrine; Mauricio Iglesias, Miguel; Valverde Perez, Borja

    2013-01-01

    A pH simulator consisting of an efficient numerical solver of a system of nine nonlinear equations was constructed and implemented in the modeling software MATLAB. The pH simulator was integrated in a granular biofilm model and used to simulate the pH profiles within granules performing...... the nitritation-anammox process for a range of operating points. The simulation results showed that pH profiles were consistently increasing with increasing depth into the granule, since the proton producing aerobic ammonium oxidizers (AOB) were located close to the granule surface.Despite this pH profile, more...... NH3 was available for AOB than for anaerobic ammonium oxidizers (AnAOB), located in the center of the granules. However, operating at a higher oxygen loading resulted in steeper changes in pH over the depth of the granule and caused the NH3 concentration profile to increase from the granule surface...

  18. pH variation and influence in an autotrophic nitrogen removing biofilm system using an efficient numerical solution strategy.

    Science.gov (United States)

    Vangsgaard, Anna Katrine; Mauricio-Iglesias, Miguel; Valverde-Pérez, Borja; Gernaey, Krist V; Sin, Gürkan

    2013-01-01

    A pH simulator consisting of an efficient numerical solver of a system of nine nonlinear equations was constructed and implemented in the modeling software MATLAB. The pH simulator was integrated in a granular biofilm model and used to simulate the pH profiles within granules performing the nitritation-anammox process for a range of operating points. The simulation results showed that pH profiles were consistently increasing with increasing depth into the granule, since the proton-producing aerobic ammonium-oxidizing bacteria (AOB) were located close to the granule surface. Despite this pH profile, more NH3 was available for AOB than for anaerobic ammonium oxidizers, located in the center of the granules. However, operating at a higher oxygen loading resulted in steeper changes in pH over the depth of the granule and caused the NH3 concentration profile to increase from the granule surface towards the center. The initial value of the background charge and influent bicarbonate concentration were found to greatly influence the simulation result and should be accurately measured. Since the change in pH over the depth of the biofilm was relatively small, the activity potential of the microbial groups affected by the pH did not change more than 5% over the depth of the granules.

  19. Removal of cesium radioisotopes from solutions using granulated zeolites

    International Nuclear Information System (INIS)

    Bronic, J.; Subotic, B.

    1991-01-01

    The influence of type of zeolite and the flow rate of solution through the column on the removal efficiency of radioactive cesium ions from solution has been investigated. The analysis of the change in the concentration of cesium ions in the solutions and distribution of cesium ions in the column fillings (granulated zeolites), after passing the solutions through the columns filled with various granulated zeolites (zeolite 4A, zeolite 13X, synthetic mordenite) was performed. On the basis of the results of this study, the conditions for the most efficient removal of cesium ions from solutions have been discussed. (author) 35 refs.; 9 figs.; 1 tab

  20. Fluoride removal from aqueous solution by pumice: case study on ...

    African Journals Online (AJOL)

    EJIRO

    conditions, the fluoride removal efficiency from Kuhbonan water by 2.8 mg/L fluoride was 74.64%. Eventually ... industrial wastewater containing fluoride is a key ..... solution using silica ceramic: Adsorption kinetics and equilibrium studies.

  1. Removal of boron from aqueous solution using cryptocrystalline magnesite

    CSIR Research Space (South Africa)

    Masindi, Vhahangwele

    2016-05-01

    Full Text Available of Water Reuse and Desalination Removal of boron from aqueous solution using cryptocrystalline magnesite Vhahangwele Masindi and Mugera W. Gitari Abstract The present study aimed to evaluate the efficiency of using cryptocrystalline magnesite...

  2. Synthesis of Ce(III)-doped Fe{sub 3}O{sub 4} magnetic particles for efficient removal of antimony from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Qi, Zenglu; Joshi, Tista Prasai [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Liu, Ruiping, E-mail: liuruiping@rcees.ac.cn [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Liu, Huijuan [University of Chinese Academy of Sciences, Beijing 100049 (China); State Key Laboratory of Environmental Aquatic Chemistry, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing, 100085 (China); Qu, Jiuhui [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); University of Chinese Academy of Sciences, Beijing 100049 (China)

    2017-05-05

    Highlights: • Doping of Ce into Fe{sub 3}O{sub 4} was achieved based on a facile solvothermal method. • After doping, the removal capacity was increased by 5 times for “Sb(V)” and 2 times for “Sb(III)”. • Decreasing pH improved adsorption of Sb(V) but decreased adsorption of Sb(III). • Antimony sorption mechanisms on Ce-doped Fe{sub 3}O{sub 4} were illustrated. - Abstract: Aqueous antimony (Sb) pollution from human activity is of great concern in drinking water due to its adverse health effect. Magnetic Fe{sub 3}O{sub 4} particles, with high separation ability from solution, have been considered as a low-cost Sb adsorbent for contaminants. However, the limited adsorption capacity has restricted its practical application. In this study, a solvothermal approach was developed for doping Ce(III) into Fe{sub 3}O{sub 4}, thereby increasing the adsorption efficacy for both Sb(III) and Sb(V). In contrast to un-doped Fe{sub 3}O{sub 4}, the adsorption capacity towards Sb(III) and Sb(V) in Ce-doped materials increased from 111.4 to 224.2 mg/g and from 37.2 to 188.1 mg/g at neutral pH, respectively. Based on the combined results of XPS, XRD, and FTIR, it confirmed that Ce atom successfully doped into the Fe{sub 3}O{sub 4} structure, resulting in the decreased particle size, increased the surface area, and isoelectric point. Furthermore, the vibrating sample magnetometer (VSM) results showed that the Ce doping process had some side effects on the primitive magnetic property, but remaining the high separation potential during water treatment. According to the high removal efficiency and magnetic property, the Ce-doped Fe{sub 3}O{sub 4} of great simplicity should be a promising adsorbent for aqueous Sb removal.

  3. Enhancing the sorption efficiency of polystyrene by immobilizing MgO and its application for uranium (VI) removal from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Elhefnawy, O.A.; Elabd, A.A. [Nuclear and Radiological Regulatory Authority (NRRA), Cairo (Egypt). Nuclear Safeguards and Physical Protection Dept.

    2016-07-01

    Magnesium oxide immobilized polystyrene (PS/MgO) was prepared by the thermal attachment method for the removal of U(VI) from aqueous solutions. PS/MgO was characterized by different techniques [scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD)]. The effects of pH, adsorbent amount, contact time, initial U(VI) concentration, temperature and co-existing cations on the removal process were investigated by using batch technique. The results showed that the maximum adsorption capacity was 163 (mg g{sup -1}) at pH 6 and 293 K. The adsorption kinetics of U(VI) onto PS/MgO followed pseudo-second order and intra-particle kinetic models. The adsorption isotherms obeyed the Freundlich isotherm model. The thermodynamic parameters show that the process is endothermic and spontaneous. PS/MgO is an attractive adsorbent for U(VI) removal from aqueous solutions due to its accessibility, low preparation cost and high removal capacity.

  4. Carbon Efficient Building Solutions

    Directory of Open Access Journals (Sweden)

    Pellervo Matilainen

    2010-03-01

    Full Text Available Traditionally, the Finnish legislation have focused on energy use and especially on energy used for heating space in buildings. However, in many cases this does not lead to the optimal concept in respect to minimizing green house gases. This paper studies how CO2 emission levels are affected by different measures to reduce energy use in buildings. This paper presents two real apartment buildings with different options of energy efficiency and power sources. The calculations clearly show that in the future electricity and domestic hot water use will have high importance in respect to energy efficiency, and therefore also CO2 equivalent (eq emissions. The importance increases when the energy efficiency of the building increases. There are big differences between average Finnish production and individual power plants; CO2 eq emissions might nearly double depending on the energy source and the power plant type. Both a building with an efficient district heating as a power source, and a building with ground heat in addition to nuclear power electricity as a complimentary electricity source performed very similarly to each other in respect to CO2 eq emissions. However, it is dangerous to conclude that it is not important which energy source is chosen. If hypothetically, the use of district heating would dramatically drop, the primary energy factor and CO2 eq emissions from electricity would rise, which in turn would lead to the increase of the ground heat systems emissions. A problem in the yearly calculations is that the fact that it is very important, sometimes even crucial, when energy is needed, is always excluded.

  5. Facile functionalized of SBA-15 via a biomimetic coating and its application in efficient removal of uranium ions from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Jun-Kai [School of Environmental Science and Engineering, Tianjin University, Tianjin 300072 (China); School of Energy and Environmental Engineering, Hebei University of Technology, Tianjin 300401 (China); Hou, Li-An; Zhang, Guang-Hui [School of Environmental Science and Engineering, Tianjin University, Tianjin 300072 (China); Gu, Ping, E-mail: guping@tju.edu.cn [School of Environmental Science and Engineering, Tianjin University, Tianjin 300072 (China)

    2015-04-09

    Highlights: • Dopamine-functionalized SBA-15 (DMS) was developed via a biomimetic coating. • The modification approach was simple, facile and cost-effective. • The DMS was firstly used to remove U(VI) from aqueous solution. • Large adsorption capacity and rapid separation were obtained. - Abstract: A novel dopamine-functionalized mesoporous silica (DMS), synthesized by grafting dopamine onto a mesoporous molecular sieve (SBA-15), was developed as a sorbent to extract U(VI) from aqueous solution. The method used to modify SBA-15 was simple, facile and cost-effective. The DMS was characterized by SEM, TEM, XRD and BET, showing that the material had an ordered mesoporous structure and a large surface area. The effect of contact time, pH, ionic strength, temperature, and solid–liquid ratio on the sorption process was investigated. It was demonstrated that the adsorption of U(VI) by DMS was fast and that it can be described by the pseudo-second order-equation where the equilibrium time was 20 min. Additionally, the adsorption isotherm data were fitted well by the Langmuir model with the maximum adsorption capacity of DMS of 196 mg/g at pH 6.0. Furthermore, the influence of the K{sup +} and Na{sup +} concentrations and solid-to-liquid ratio on the sorption was very weak, and the values of the thermodynamic parameters revealed that the sorption process was exothermic and spontaneous. All the results suggested that the DMS could be used as an excellent adsorbent to remove U(VI) from aqueous solution.

  6. Removing Phosphorus from Aqueous Solutions Using Lanthanum Modified Pine Needles.

    Directory of Open Access Journals (Sweden)

    Xianze Wang

    Full Text Available The renewable pine needles was used as an adsorbent to remove phosphorus from aqueous solutions. Using batch experiments, pine needles pretreated with alkali-isopropanol (AI failed to effectively remove phosphorus, while pine needles modified with lanthanum hydroxide (LH showed relatively high removal efficiency. LH pine needles were effective at a wide pH ranges, with the highest removal efficiency reaching approximately 85% at a pH of 3. The removal efficiency was kept above 65% using 10 mg/L phosphorus solutions at desired pH values. There was no apparent significant competitive behavior between co-existing anions of sulfate, nitrate, and chloride (SO4(2-, NO3(- and Cl(-; however, CO3(2- exhibited increased interfering behavior as concentrations increased. An intraparticle diffusion model showed that the adsorption process occurred in three phases, suggesting that a boundary layer adsorption phenomena slightly affected the adsorption process, and that intraparticle diffusion was dominant. The adsorption process was thermodynamically unfavorable and non-spontaneous; temperature increases improved phosphorus removal. Total organic carbon (TOC assays indicated that chemical modification reduced the release of soluble organic compounds from 135.6 mg/L to 7.76 mg/L. This new information about adsorption performances provides valuable information, and can inform future technological applications designed to remove phosphorus from aqueous solutions.

  7. Humic acid removal from aqueous solutions by peroxielectrocoagulation process

    Directory of Open Access Journals (Sweden)

    Ahmad Reza Yazdanbakhsh

    2015-06-01

    Full Text Available Background: Natural organic matter is the cause of many problems associated with water treatment such as the presence of disinfection by-products (DBPs and membrane fouling during water filtration. In this study, the performance of the peroxi-electrocoagulation process (PEP was investigated for the removal of humic acids (HAs from aqueous solutions. Methods: PEP was carried out for the removal of HA using a plexiglas reactor with a volume of 2 L and fitted with iron electrodes and a direct current supply (DC. Samples were taken at various amounts of pH (2-4, current density (1 and 2A/cm2, hydrogen peroxide (50-150 mg/L and reaction time (5-20 minutes and then filtered to remove sludge formed during reaction. Finally, the HA concentration was measured by UV absorbance at 254 nm (UV254. Results: Results indicated that increasing the concentration of H2O2 from 50 to 150 mg/L increased HA removal efficiency from 83% to 94.5%. The highest removal efficiency was observed at pH 3.0; by increasing the pH to the alkaline range, the efficiency of the process was reduced. It was found that HA removal efficiency was high in current density 1A/cm2. Increasing current density up to 1 A cm-2 caused a decrease in removal efficiency. Results of this study showed that under the optimum operating range for the process ([current density] = 1A/cm2, [hydrogen peroxide concentration] = 150 mg/L, [reaction time]= 20 minutes and [pH]= 3.0, HA removal efficiency reached 98%. Conclusion: It can be concluded that PEP has the potential to be utilized for cost-effective removal of HA from aqueous solutions.

  8. Facile functionalized of SBA-15 via a biomimetic coating and its application in efficient removal of uranium ions from aqueous solution.

    Science.gov (United States)

    Gao, Jun-Kai; Hou, Li-An; Zhang, Guang-Hui; Gu, Ping

    2015-04-09

    A novel dopamine-functionalized mesoporous silica (DMS), synthesized by grafting dopamine onto a mesoporous molecular sieve (SBA-15), was developed as a sorbent to extract U(VI) from aqueous solution. The method used to modify SBA-15 was simple, facile and cost-effective. The DMS was characterized by SEM, TEM, XRD and BET, showing that the material had an ordered mesoporous structure and a large surface area. The effect of contact time, pH, ionic strength, temperature, and solid-liquid ratio on the sorption process was investigated. It was demonstrated that the adsorption of U(VI) by DMS was fast and that it can be described by the pseudo-second order-equation where the equilibrium time was 20 min. Additionally, the adsorption isotherm data were fitted well by the Langmuir model with the maximum adsorption capacity of DMS of 196 mg/g at pH 6.0. Furthermore, the influence of the K(+) and Na(+) concentrations and solid-to-liquid ratio on the sorption was very weak, and the values of the thermodynamic parameters revealed that the sorption process was exothermic and spontaneous. All the results suggested that the DMS could be used as an excellent adsorbent to remove U(VI) from aqueous solution. Copyright © 2014 Elsevier B.V. All rights reserved.

  9. The removal of actinide metals from solution

    International Nuclear Information System (INIS)

    Hancock, R.D.; Howell, I.V.

    1980-01-01

    A process is specified for removing actinide metals (e.g. uranium) from solutions. The solution is contacted with a substrate comprising the product obtained by reacting an inorganic solid containing surface hydroxyl groups (e.g. silica gel) with a compound containing a silane grouping, a nitrogen-containing group (e.g. an amine) and other specified radicals. After treatment, the actinide metal is recovered from the substrate. (U.K.)

  10. Removal of radium from aqueous sulphate solutions

    International Nuclear Information System (INIS)

    Weir, D.R.; Masters, J.T.; Neven, M.

    1983-01-01

    Radium is often present in ores and an aqueous solution associated with the ore may consequently contain dissolved radium. It is frequently necessary to remove radium from such solutions to reduce the total radium content to a prescribed low level before the solution can be returned to the environment. The present invention is based on the discovery that the total radium content can be reduced to a satisfactory level within a reasonable time by adding a soluble barium salt to a radium-containing sulphate solution which also contains dissolved magnesium at a pH not greater than about 0 to precipitate radium as barium radium sulphate, raising the pH to at least 11 to precipitate an insoluble magnesium compound which collects the barium radium sulphate precipitate, and separating substantially all of the precipitates from the solution

  11. Removal of Phenol in Aqueous Solution Using Kaolin Mineral Clay

    International Nuclear Information System (INIS)

    Sayed, M.S.

    2008-01-01

    Kaolin clay were tested for phenol removal as toxic liquid waste from aqueous waste water. Several experimental conditions such as weight and particle size of clay were investigated to study batch kinetic techniques, also the ph and concentration of the phenol solution were carried out. The stability of the Langmuir adsorption model of the equilibrium data were studied for phenol sorbent clay system. Infrared spectra, thermogravimetric and differential thermal analysis techniques were used to characterize the behavior of kaolin clay and kaolin clay saturated with phenol. The results obtained showed that kaolin clay could be used successfully as an efficient sorbent material to remove phenol from aqueous solution

  12. In-situ synthesis of SiO2@MOF composites for high-efficiency removal of aniline from aqueous solution

    Science.gov (United States)

    Han, Tongtong; Li, Caifeng; Guo, Xiangyu; Huang, Hongliang; Liu, Dahuan; Zhong, Chongli

    2016-12-01

    A series of SiO2@aluminum-MOF(MIL-68) composites with different SiO2 loadings have been synthesized by a simple and mild compositing strategy for high-efficiency removal of aniline. As evidenced from SEM and TEM images as well as the particle size distribution, the incorporation of SiO2 can improve the dispersity of MIL-68(Al) in composites, and result in the smaller particle size than that of pristine MIL-68(Al). Besides, the adsorption of aniline over SiO2, MIL-68(Al), the physical mixture of these two materials, and SiO2@MIL-68(Al) composites was investigated comparatively, demonstrating a relatively high adsorption capacity (531.9 mg g-1) of 7% SiO2@MIL-68(Al) towards aniline. Combining the ultrafast adsorption dynamics (reaching equilibrium within 40 s) and great reusability, 7% SiO2@MIL-68(Al) shows excellent adsorption performance. This indicates that the SiO2@MIL-68(Al) composites possess great potential applications as a kind of fascinating adsorbent in water pollution protection.

  13. Nanosized yolk–shell Fe{sub 3}O{sub 4}@Zr(OH){sub x} spheres for efficient removal of Pb(II) from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Shunlong [Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China); Li, Jiansheng, E-mail: lijsh@mail.njust.edu.cn [Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China); Wan, Gaojie; Liu, Chao [Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China); Fan, Wenhong, E-mail: fanwh@buaa.edu.cn [Department of Environmental Science and Engineering, School of Chemistry and Environment, Beihang University, Beijing 100191 (China); Wang, Lianjun, E-mail: wanglj@mail.njust.edu.cn [Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China)

    2016-05-15

    Highlights: • Well dispersed and easy separated nanoadsorbents with stable chemical property are highly desired. • Fe{sub 3}O{sub 4}@Zr(OH){sub x} yolk–shell nanospheres (YSNs) nanoadsorbents were prepared. • Enhanced Pb(II) adsorption capacity of 310.8 mg/g was achieved on Fe{sub 3}O{sub 4}@Zr(OH){sub x} YSNs based on Zr weight. • The cavities in Fe{sub 3}O{sub 4}@Zr(OH){sub x} YSNs is responsible for the improved performance. - Abstract: In this work, Fe{sub 3}O{sub 4}@Zr(OH){sub x} yolk–shell nanospheres (YSNs) were synthesized via a two-step process and further examined as adsorbents for the removal of Pb(II). To understand the hollow structure on the adsorption properties of Pb(II), another adsorbent without hollow cavities, i.e., Fe{sub 3}O{sub 4}@SiO{sub 2}@Zr(OH){sub x} core–shell nanospheres (CSNs), was also prepared for comparison. The adsorption results showed that Fe{sub 3}O{sub 4}@Zr(OH){sub x} YSNs exhibited 41.6% higher Pb(II) adsorption capacity as compared to that of Fe{sub 3}O{sub 4}@SiO{sub 2}@Zr(OH){sub x} CSNs. The isotherm was well fitted to Langmuir adsorption model with q{sub max} value of 310.8 mg/g after normalized by the weight of Zr in Fe{sub 3}O{sub 4}@Zr(OH){sub x} YSNs. Scanning transmission electron microscopy (STEM) mapping results revealed that the existence of cavities between Fe{sub 3}O{sub 4} cores and Zr(OH){sub x} shells is responsible for the improved adsorption performance. XPS analysis indicated the surface hydroxyl groups played a key role in the Pb(II) adsorption. The removal efficiency of Pb(II) was maintained above 90% in five consecutive adsorption–desorption cycles.

  14. Removal of Nitrate From Aqueous Solution Using Rice Chaff

    Directory of Open Access Journals (Sweden)

    Dehghani

    2015-09-01

    Full Text Available Background Nitrate is largely dissolved in the surface and ground water, due to its high solubility. Continual uptake of nitrite through drinking water can lead to problems and diseases (such as blue baby for humans, especially children. Objectives The aim of this study was to develop a new and inexpensive method for the removal of nitrate from water. In this regard, the possibility of using chaff for removal of nitrate from aqueous solutions was studied and the optimum operating conditions of nitrate removal was determined. Materials and Methods This is a cross-sectional study conducted in laboratory scale. The UV spectrophotometer at a wavelength of maximum absorbance (220 nm was used to determine the nitrate concentration. The effect of pH, amount of chaff, temperature, and contact time were investigated. Results The result of this study revealed that chaff as an absorbent could remove nitrate from solutions, and the efficiency of adsorption increased as contact time increased from 5 to 30 minutes, amount of chaff increased from 1 to 3 g, temperature increased in a range of 300 - 400°C and the amount of pH decreased from 10 to 3. The maximum adsorption rate was around pH 3 (53.14%. Conclusions It was shown that the removal efficiency of nitrate was directly proportional to the amount of chaff, temperature, and contact time but inversely to the pH. This study showed that nitrate removal by chaff is a promising technique.

  15. Removal of Uranium by Exchanger Resins from Soil Washing Solution

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seung Soo; Han, G. S.; Kim, G. N.; Koo, D. S.; Jeong, J. W.; Moon, J. K. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Uranyl ions in the acidic waste solution were sorbed on AM-resin resin with a high sorption efficiency, and desorbed from the resin by a batch-type washing with a 60 .deg. C heated 0.5 M Na{sub 2}CO{sub 3} solution. However, the uranium dissolved in the sulfuric acid solution was not sorbed onto the strong anion exchanger resins. Our group has developed a decontamination process with washing and electrokinetic methods for uranium-contaminated (U-contaminated) soil. However, this process generates a large amount of waste solution containing various metal ions. If the uranium selectively removed from the waste solution, a very small amount of the 2nd waste would be generated. Thus, selective sorption of uranium by ion exchange resins was examined in this study.

  16. Arsenic removal from acidic solutions with biogenic ferric precipitates

    Energy Technology Data Exchange (ETDEWEB)

    Ahoranta, Sarita H., E-mail: sarita.ahoranta@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Kokko, Marika E., E-mail: marika.kokko@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Papirio, Stefano, E-mail: stefano.papirio@unicas.it [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Özkaya, Bestamin, E-mail: bozkaya@yildiz.edu.tr [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Department of Environmental Engineering, Yildiz Technical University, Davutpasa Campus 34220, Esenler, Istanbul (Turkey); Puhakka, Jaakko A., E-mail: jaakko.puhakka@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland)

    2016-04-05

    Highlights: • Continuous and rapid arsenic removal with biogenic jarosite was achieved at pH 3.0. • Arsenic removal was inefficient below pH 2.4 due to reduced Fe–As co-precipitation. • As(V) had better sorption characteristics than As(III). • Biogenic jarosite adsorbed arsenic more effectively than synthetic jarosite. - Abstract: Treatment of acidic solution containing 5 g/L of Fe(II) and 10 mg/L of As(III) was studied in a system consisting of a biological fluidized-bed reactor (FBR) for iron oxidation, and a gravity settler for iron precipitation and separation of the ferric precipitates. At pH 3.0 and FBR retention time of 5.7 h, 96–98% of the added Fe(II) precipitated (99.1% of which was jarosite). The highest iron oxidation and precipitation rates were 1070 and 28 mg/L/h, respectively, and were achieved at pH 3.0. Subsequently, the effect of pH on arsenic removal through sorption and/or co-precipitation was examined by gradually decreasing solution pH from 3.0 to 1.6 (feed pH). At pH 3.0, 2.4 and 1.6, the highest arsenic removal efficiencies obtained were 99.5%, 80.1% and 7.1%, respectively. As the system had ferric precipitates in excess, decreased arsenic removal was likely due to reduced co-precipitation at pH < 2.4. As(III) was partially oxidized to As(V) in the system. In shake flask experiments, As(V) sorbed onto jarosite better than As(III). Moreover, the sorption capacity of biogenic jarosite was significantly higher than that of synthetic jarosite. The developed bioprocess simultaneously and efficiently removes iron and arsenic from acidic solutions, indicating potential for mining wastewater treatment.

  17. Efficient removal of H2S at high temperature using the ionic liquid solutions of [C4mim]3PMo12O40-An organic polyoxometalate.

    Science.gov (United States)

    Ma, Yunqian; Liu, Xinpeng; Wang, Rui

    2017-06-05

    An innovative approach to H 2 S capture and sulfur recovery via liquid redox at high temperature has been developed using [C 4 mim] 3 PMo 12 O 40 at temperatures ranging from 80 to 180°C, which is superior to the conventional water-based system with an upper limit of working temperature normally below 60°C. The ionic liquids used as solvents include [C 4 mim]Cl, [C 4 mim]BF 4 , [C 4 mim]PF 6 and [C 4 mim]NTf 2 . Microscopic observation and turbidity measurement were used to investigate the dissolution of [C 4 mim] 3 PMo 12 O 40 in the ionic liquids. Stabilization energy between H 2 S and the anion of ionic liquid as well as H 2 O was calculated to illustrate the interaction between H 2 S and the solvents. The cavity theory can be adopted to illustrate the mechanism for H 2 S absorption: the Cl - ion with small radius can be incorporated into the cavities of [C 4 mim] 3 PMo 12 O 40 , and interact with H 2 S strongly. The underlying mechanism for sulfur formation is the redox reaction between H 2 S and PMo 12 O 40 3- . H 2 S can be oxidized to elemental sulfur and Mo 6+ is partly reduced during absorption, according to UV-vis and FTIR spectra. The [C 4 mim] 3 PMo 12 O 40 -[C 4 mim]Cl after reaction can be readily regenerated by air and thus enabling its efficient and repeatitive use. The absorbent of [C 4 mim] 3 PMo 12 O 40 -ionic liquid system provides a new approach for wet oxidation desulfurization at high temperature. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Synthesis and characterization of sulfur functionalized graphene oxide nanosheets as efficient sorbent for removal of Pb2+, Cd2+, Ni2+ and Zn2+ ions from aqueous solution: A combined thermodynamic and kinetic studies

    Science.gov (United States)

    Pirveysian, Mahtab; Ghiaci, Mehran

    2018-01-01

    A very simple, one pot method was used for preparation of sulfur functionalized graphene oxide (GO-SOxR) with sodium sulfide and water in reflux condition. The elemental analysis data showed high sulfur content up to 15%. EDS and XPS analysis also proved introduction of sulfur element. To make the sorbent more efficient operationally, the GO-SOxR was coated with a mesoporous shell of TiO2 or SiO2. The prepared sorbents were characterized by SEM, TEM, TGA, XPS, XRD, IR and EDS. GO-SOxR@TiO2 and GO-SOxR@SiO2 composites were tested for removal of Pb(II), Cd(II), Ni(II) and Zn(II) as heavy metal ions from aqueous solution in batch method. Adsorption of the heavy metal ions was studied kinetically, and the adsorption capacities of GO-SOxR, GO-SOxR@TiO2, and GO-SOxR@SiO2 were evaluated using equilibrium adsorption isotherms, and compared to other adsorbents used for removal of these heavy metals. Kinetic studies showed that the experimental data was fitted with pseudo second order model. The adsorption capacity of GO was significantly improved by sulfur functionalization and TiO2 coating.

  19. Removal of strontium ions from solutions using granulated zeolites

    International Nuclear Information System (INIS)

    Bronic, J.; Subotic, B.

    1992-01-01

    The ion-exchange process on columns filled with granulated zeolites is determined by several physico-chemical parameters. The influence of these parameters (zeolite type, concentration of exchangeable ions in solution, temperature, flow rate, etc.) on the kinetics of ion-exchange process was studied by measuring the Sr 2+ ion concentration in solution before and after passing through a column filled with various granulated zeolites (zeolite 13X, zeolite A and synthetic mordenite). Using the experimental technique of radioactive labeling by 89 Sr, the distribution of Sr 2+ ions in column fillings were also determined. From the results obtained, the optimal conditions for the most efficient removal of strontium ions from solutions using granulated zeolites can be defined. (author) 24 refs.; 9 figs

  20. Arsenic removal from acidic solutions with biogenic ferric precipitates.

    Science.gov (United States)

    Ahoranta, Sarita H; Kokko, Marika E; Papirio, Stefano; Özkaya, Bestamin; Puhakka, Jaakko A

    2016-04-05

    Treatment of acidic solution containing 5g/L of Fe(II) and 10mg/L of As(III) was studied in a system consisting of a biological fluidized-bed reactor (FBR) for iron oxidation, and a gravity settler for iron precipitation and separation of the ferric precipitates. At pH 3.0 and FBR retention time of 5.7h, 96-98% of the added Fe(II) precipitated (99.1% of which was jarosite). The highest iron oxidation and precipitation rates were 1070 and 28mg/L/h, respectively, and were achieved at pH 3.0. Subsequently, the effect of pH on arsenic removal through sorption and/or co-precipitation was examined by gradually decreasing solution pH from 3.0 to 1.6 (feed pH). At pH 3.0, 2.4 and 1.6, the highest arsenic removal efficiencies obtained were 99.5%, 80.1% and 7.1%, respectively. As the system had ferric precipitates in excess, decreased arsenic removal was likely due to reduced co-precipitation at pHremoves iron and arsenic from acidic solutions, indicating potential for mining wastewater treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

  1. Natural organic matters removal efficiency by coagulation

    Science.gov (United States)

    Sapingi, Mohd Sharizal Mohd; Pishal, Munirah; Murshed, Mohamad Fared

    2017-10-01

    The presence of Natural Organic Matter (NOM) in surface water results in unwanted characteristics in terms of color, odor, and taste. NOM content reaction with free chlorine in treated water lowers the water quality further. Chlorine is added for disinfection and produces undesirable disinfection by-products (DPBs). DBPs in drinking water are carcinogenic to consumers and may promote cancerous cell development in the human body. This study was performed to compare the coagulant efficiency of aluminum sulfate (Alum) and ferric chloride (FeCl3) on NOM removal (as in UV254 absorbance) and turbidity removal under three pH conditions (pH 6, pH 7, and sample actual pH). The three sampling points for these studies were Jalan Baru River, Kerian River, and Redac Pond. Additional sampling points, such as Lubuk Buntar and a tubewell located in the Civil Engineering School, were included to observe differences in characteristics. DOC, UV absorbance, and full wavelength were tested, after which samples treated with alum were also tested to further analyze the NOM content. Based on UV254 absorbance and DOC data, specific UV value was calculated to obtain vital synopsis of the characteristics of NOM content, as well as coagulation efficiency.

  2. Removal of Diazinon from aqueous solution by electrocoagulation process using aluminum electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Amooey, Ali Akbar; Ghasemi, Shahram; Mirsoleimani-azizi, Seyed Mohammad; Gholaminezhad, Zohreh; Chaichi, Mohammad Javad [University of Mazandaran, Babolsar (Iran, Islamic Republic of)

    2014-06-15

    Electrocoagulation (EC) is an electrochemical method to treat polluted wastewaters and aqueous solutions. In this paper, the removal of Diazinon was studied by EC on aluminum electrode. The effect of several parameters such as initial concentration of Diazinon, current density, solution conductivity, effect of pH, and electrolysis time were investigated on EC performance. The obtained results showed that the removal efficiency of EC depends on the current density, initial concentration of Diazinon and electrolysis time. The optimum pH is 3 and also the solution conductivity has no significant effect on removal efficiency.

  3. Removal of Diazinon from aqueous solution by electrocoagulation process using aluminum electrodes

    International Nuclear Information System (INIS)

    Amooey, Ali Akbar; Ghasemi, Shahram; Mirsoleimani-azizi, Seyed Mohammad; Gholaminezhad, Zohreh; Chaichi, Mohammad Javad

    2014-01-01

    Electrocoagulation (EC) is an electrochemical method to treat polluted wastewaters and aqueous solutions. In this paper, the removal of Diazinon was studied by EC on aluminum electrode. The effect of several parameters such as initial concentration of Diazinon, current density, solution conductivity, effect of pH, and electrolysis time were investigated on EC performance. The obtained results showed that the removal efficiency of EC depends on the current density, initial concentration of Diazinon and electrolysis time. The optimum pH is 3 and also the solution conductivity has no significant effect on removal efficiency

  4. Arsenic Removal from Aqueous Solutions by Salvadora persica Stem Ash

    Directory of Open Access Journals (Sweden)

    Ferdos Kord Mostafapour

    2013-01-01

    Full Text Available Arsenic is a naturally occurring metalloid, which is widely distributed in nature and is regarded as the largest mass poisoning in history. In the present study, the adsorption potential of Salvadora persica (S. persica stem ash in a batch system for the removal of As(V from aqueous solutions was investigated. Isotherm studies were carried out to evaluate the effect of contact time (20–240 min, pH (2–11, initial arsenic concentration (50–500 μg/L, and adsorbent dose on sorption efficiency. Maximum removal efficiency of 98.33% and 99.32% was obtained at pH 6, adsorbent dosage 3.5 g/L, initial As(V concentration 500 μg/L, and contact time 80 and 60 min for S. persica stem ash at 300 °C and 500 °C, respectively. Also, the adsorption equilibriums were analyzed by the Langmuir and Freundlich isotherm models. Such equilibriums showed that the adsorption data was well fitted with the Freundlich isotherm model for S. persica stem ash at both 300 °C and 500 °C (R2=0.8983 and 0.9274, resp.. According to achieved results, it was defined that S. persica stem ash can be used effectively for As(V removal from the aqueous environment.

  5. Study of the removal of metronidazole from aqueous solutions using Electro/ Fenton process and graphite and iron electrodes

    Directory of Open Access Journals (Sweden)

    Bahram Kamarehie

    2018-04-01

    Conclusion: The Electro-Fenton process can effectively remove metronidazole from aquatic solutions in environmentally convenient conditions. This process can be used as an efficient method for removing other persistent pollutants from the environment.

  6. The influence of small-scale interlayer heterogeneity on DDT removal efficiency for flushing technology

    Science.gov (United States)

    Wang, Xingwei; Chen, Jiajun

    2017-06-01

    With an aim to investigate the influence of small-scale interlayer heterogeneity on DDT removal efficiency, batch test including surfactant-stabilized foam flushing and solution flushing were carried out. Two man-made heterogeneous patterns consisting of coarse and fine quartz sand were designed to reveal the influencing mechanism. Moreover, the removal mechanism and the corresponding contribution by foam flushing were quantitatively studied. Compared with surfactant solution flushing, the DDT removal efficiency by surfactant-stabilized foam flushing increased by 9.47% and 11.28% under heterogeneous patterns 1 and 2, respectively. The DDT removal contributions of improving sweep efficiency for heterogeneous patterns 1 and 2 by foam flushing were 40.82% and 45.98%, and the contribution of dissolving capacity were 59.18% and 54.02%, respectively. The dissolving capacity of DDT played a major role in DDT removal efficiency by foam flushing under laboratory conditions. And the DDT removal contribution of significant improving sweep efficiency was higher than that of removal decline caused by weak solubilizing ability of foam film compared with solution flushing. The obtained results indicated that the difference of DDT removal efficiency by foam flushing was decreased under two different heterogeneous patterns with the increase of the contribution of improving foam flushing sweep efficiency. It suggested that foam flushing can reduce the disturbance from interlayer heterogeneity in remediating DDT contaminated heterogeneous medium.

  7. Trace metal removal from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, R. (ed.)

    1986-01-01

    The Industrial Division of the Royal Society of Chemistry organized the symposium, held at the University of Warwick, that gave rise to the 12 typescript papers in this softbound volume. Both biological and chemical methods of recovering or removing metals from water are discussed, and two papers are concerned solely with analysis. Not indexed.

  8. Nanotoxicity modelling and removal efficiencies of ZnONP.

    Science.gov (United States)

    Fikirdeşici Ergen, Şeyda; Üçüncü Tunca, Esra

    2018-01-02

    In this paper the aim is to investigate the toxic effect of zinc oxide nanoparticles (ZnONPs) and is to analyze the removal of ZnONP in aqueous medium by the consortium consisted of Daphnia magna and Lemna minor. Three separate test groups are formed: L. minor ([Formula: see text]), D. magna ([Formula: see text]), and L. minor + D. magna ([Formula: see text]) and all these test groups are exposed to three different nanoparticle concentrations ([Formula: see text]). Time-dependent, concentration-dependent, and group-dependent removal efficiencies are statistically compared by non-parametric Mann-Whitney U test and statistically significant differences are observed. The optimum removal values are observed at the highest concentration [Formula: see text] for [Formula: see text], [Formula: see text] for [Formula: see text]and [Formula: see text] for [Formula: see text] and realized at [Formula: see text] for all test groups [Formula: see text]. There is no statistically significant differences in removal at low concentrations [Formula: see text] in terms of groups but [Formula: see text] test groups are more efficient than [Formula: see text] test groups in removal of ZnONP, at [Formula: see text] concentration. Regression analysis is also performed for all prediction models. Different models are tested and it is seen that cubic models show the highest predicted values (R 2 ). In toxicity models, R 2 values are obtained at (0.892, 0.997) interval. A simple solution-phase method is used to synthesize ZnO nanoparticles. Dynamic Light Scattering and X-Ray Diffraction (XRD) are used to detect the particle size of synthesized ZnO nanoparticles.

  9. Removal of iron contaminant from zirconium chloride solution

    International Nuclear Information System (INIS)

    Voit, D.O.

    1992-01-01

    This patent describes a process for eliminating iron contaminant from an aqueous zirconium chloride solution that has been contaminated with FeCl 3 in a plant in which zirconium and hafnium chloride solutions are separated by a main MINK solvent extraction system and the FeCl 3 is normally removed from the zirconium chloride solution by a secondary MINK solvent extraction system

  10. Process for removing mercury from aqueous solutions

    Science.gov (United States)

    Googin, John M.; Napier, John M.; Makarewicz, Mark A.; Meredith, Paul F.

    1986-01-01

    A process for removing mercury from water to a level not greater than two parts per billion wherein an anion exchange material that is insoluble in water is contacted first with a sulfide containing compound and second with a compound containing a bivalent metal ion forming an insoluble metal sulfide. To this treated exchange material is contacted water containing mercury. The water containing not more than two parts per billion of mercury is separated from the exchange material.

  11. Electrocoagulation-Adsorption to Remove Anionic and Cationic Dyes from Aqueous Solution by PV-Energy

    OpenAIRE

    Castañeda-Díaz, J.; Pavón-Silva, T.; Gutiérrez-Segura, E.; Colín-Cruz, A.

    2017-01-01

    The cationic dye malachite green (MG) and the anionic dye Remazol yellow (RY) were removed from aqueous solutions using electrocoagulation-adsorption processes. Batch and continuous electrocoagulation procedures were performed and compared. Carbonaceous materials obtained from industrial sewage sludge and commercial activated carbons were used to adsorb dyes from aqueous solutions in column systems with a 96–98% removal efficiency. The continuous electrocoagulation-adsorption system was more ...

  12. A study on removal of elemental mercury in flue gas using fenton solution

    International Nuclear Information System (INIS)

    Liu, Yangxian; Wang, Yan; Wang, Qian; Pan, Jianfeng; Zhang, Yongchun; Zhou, Jianfei; Zhang, Jun

    2015-01-01

    Highlights: • A novel technique on oxidation of Hg 0 using Fenton was proposed. • The effects of several process parameters on Hg 0 removal were studied. • Products and ·OH in solution were detected. • Reaction mechanism of Hg 0 removal was studied. • Simultaneous removal of Hg 0 , NO and SO 2 was also studied. - Abstract: A novel technique on oxidation-separation of elemental mercury (Hg 0 ) in flue gas using Fenton solution in a bubbling reactor was proposed. The effects of several process parameters (H 2 O 2 concentration, Hg 0 inlet concentration, Fe 2+ concentration, solution temperature, solution pH, gas flow) and several flue gas components (NO, SO 2 , O 2 , CO 2 , inorganic ions and particulate matters on Hg 0 removal were studied. The results indicate that H 2 O 2 concentration, Fe 2+ concentration, solution pH and gas flow have great effects on Hg 0 removal. Solution temperature, Hg 0 , NO, SO 2 , CO 3 2− and HCO 3 − concentrations also have significant effects on Hg 0 removal. However, Cl − , SO 4 2− , NO 3 − , O 2 and CO 2 concentrations only have slight effects on Hg 0 removal. Furthermore, reaction mechanism of Hg 0 removal and simultaneous removal process of Hg 0 , NO and SO 2 were also studied. Hg 0 is removed by oxidation of ·OH and oxidation of H 2 O 2 . The simultaneous removal efficiencies of 100% for SO 2 , 100% for Hg 0 and 88.3% for NO were obtained under optimal test conditions. The results demonstrated the feasibility of Hg 0 removal and simultaneous removal of Hg 0 , SO 2 and NO using Fenton solution in a bubbling reactor

  13. Virus removal efficiency of Cambodian ceramic pot water purifiers.

    Science.gov (United States)

    Salsali, Hamidreza; McBean, Edward; Brunsting, Joseph

    2011-06-01

    Virus removal efficiency is described for three types of silver-impregnated, ceramic water filters (CWFs) produced in Cambodia. The tests were completed using freshly scrubbed filters and de-ionized (DI) water as an evaluation of the removal efficiency of the virus in isolation with no other interacting water quality variables. Removal efficiencies between 0.21 and 0.45 log are evidenced, which is significantly lower than results obtained in testing of similar filters by other investigators utilizing surface or rain water and a less frequent cleaning regime. Other experiments generally found virus removal efficiencies greater than 1.0 log. This difference may be because of the association of viruses with suspended solids, and subsequent removal of these solids during filtration. Variability in virus removal efficiencies between pots of the same manufacturer, and observed flow rates outside the manufacturer's specifications, suggest tighter quality control and consistency may be needed during production.

  14. Energy efficient trace removal by extractive distillation

    NARCIS (Netherlands)

    Jongmans, M.T.G.

    2012-01-01

    Separation processes contribute for about 40–70 % to the total energy requirements of the chemical process industry. Especially when trace removal is required to manufacture high purity products, traditional separation technologies become extremely expensive and are not providing satisfying

  15. Biosorptive removal of cobalt (II) ions from aqueous solution by ...

    African Journals Online (AJOL)

    hope&shola

    2010-11-29

    Nov 29, 2010 ... chemical reaction, decay, adsorption and biodegradation. The presence of ... sted coffee (Dakiky et al., 2002), waste tea (Ahluwalia and Goyal, 2005) ..... green removal from aqueous solution by citric acid modified rice straw.

  16. Heavy metal removal from aqueous solutions by sorption using ...

    African Journals Online (AJOL)

    Heavy metal removal from aqueous solutions by sorption using natural clays from Burkina Faso. ... The high alkaline pH in one of the samples is attributable to the presence of ... The point of zero charge (pHpzc) values of the clays, as determined by ... significant contributions to the removal of metal ions in aqueous systems.

  17. Removal of paraquat solution onto zeolite material

    Science.gov (United States)

    Sirival, Rujikarn; Patdhanagul, Nopbhasinthu; Preecharram, Sutthidech; Photharin, Somkuan

    2018-04-01

    The purpose of this research was to study the adsorption of paraquat herbicides onto zeolite Y materials by the batch method. Three adsorbents material: Zeolite-3, Zeolite-10, and Zeolite-100 were Si/Al ratio at 3.58, 8.57 and 154.37, respectively. The factors for adsorption of paraquat as follows, adsorption time, initial concentrations of paraquat, pH and adsorption isotherm were investigated. The results showed that zeolite-10 had higher adsorption capacity than zeolite-3 and zeolite-100. The appropriate conditions for adsorption were 24 h., Zeolite 0.1 g., Initial paraquat concentration 100 ppm at pH 6. The adsorption isotherm was found to correspond with Langmuir Isotherm and the maximum paraquat adsorption is 26.38 mg/g for zeolite-10, 21.41 mg/g and 9.60 mg/g for zeolite-3 and zeolite-100, respectively. The characterization of zeolite material with XRD, XRF and BET. Furthermore, the zeolite materials applied to remove other organic and inorganic wastewater.

  18. Removal mechanism of phosphate from aqueous solution by fly ash.

    Science.gov (United States)

    Lu, S G; Bai, S Q; Zhu, L; Shan, H D

    2009-01-15

    This work studied the effectiveness of fly ash in removing phosphate from aqueous solution and its related removal mechanism. The adsorption and precipitation of phosphate by fly ash were investigated separately in order to evaluate their role in the removal of phosphate. Results showed that the removal of phosphate by fly ash was rapid. The removal percentage of phosphate in the first 5min reached 68-96% of the maximum removal of phosphate by fly ash. The removal processes of phosphate by fly ash included a fast and large removal representing precipitation, then a slower and longer removal due to adsorption. The adsorption of phosphate on fly ash could be described well by Freundlich isotherm equation. The pH and Ca2+ concentration of fly ash suspension were decreased with the addition of phosphate, which suggests that calcium phosphate precipitation is a major mechanism of the phosphate removal. Comparison of the relative contribution of the adsorption and precipitation to the total removal of phosphate by fly ash showed that the adsorption accounted for 30-34% of the total removal of phosphate, depending on the content of CaO in fly ash. XRD patterns of the fly ash before and after phosphate adsorption revealed that phosphate salt (CaHPO4 x 2H2O) was formed in the adsorption process. Therefore, the removal of phosphate by fly ash can be attributed to the formation of phosphate precipitation as a brushite and the adsorption on hydroxylated oxides. The results suggested that the use of fly ash could be a promising solution to the removal of phosphate in the wastewater treatment and pollution control.

  19. (suspended solids and metals) removal efficiencies

    African Journals Online (AJOL)

    ABSTRACT. Presented in this paper are the results of correlational analyses and logistic regression between metal substances (Cd, Cu,. Pb, Zn), as well as suspended solids removal, and physical pond parameters of 19 stormwater retention pond case studies obtained from the International Stormwater BMP database.

  20. Scale up of 2,4-dichlorophenol removal from aqueous solutions using Brassica napus hairy roots

    Energy Technology Data Exchange (ETDEWEB)

    Angelini, Vanina A. [Departamento de Biologia Molecular, FCEFQN, Universidad Nacional de Rio Cuarto, 5800 Rio Cuarto, Cordoba (Argentina); Orejas, Joaquin [Facultad de Ingenieria, Universidad Nacional de Rio Cuarto, 5800 Rio Cuarto, Cordoba (Argentina); Medina, Maria I. [Departamento de Biologia Molecular, FCEFQN, Universidad Nacional de Rio Cuarto, 5800 Rio Cuarto, Cordoba (Argentina); Agostini, Elizabeth, E-mail: eagostini@exa.unrc.edu.ar [Departamento de Biologia Molecular, FCEFQN, Universidad Nacional de Rio Cuarto, 5800 Rio Cuarto, Cordoba (Argentina)

    2011-01-15

    Research highlights: {yields}B. napus hairy roots were effectively used for a large scale removal of 2,4-DCP. {yields} High removal efficiencies were obtained (98%) in a short time (30 min). {yields} Roots were re-used for six consecutive cycles with high efficiency. {yields} Post removal solutions showed no toxicity. {yields} This method could be used for continuous and safe treatment of phenolic effluents. - Abstract: Chlorophenols are harmful pollutants, frequently found in the effluents of several industries. For this reason, many environmental friendly technologies are being explored for their removal from industrial wastewaters. The aim of the present work was to study the scale up of 2,4-dichlorophenol (2,4-DCP) removal from synthetic wastewater, using Brassica napus hairy roots and H{sub 2}O{sub 2} in a discontinuous stirred tank reactor. We have analyzed some operational conditions, because the scale up of such process was poorly studied. High removal efficiencies were obtained (98%) in a short time (30 min). When roots were re-used for six consecutive cycles, 2,4-DCP removal efficiency decreased from 98 to 86%, in the last cycle. After the removal process, the solutions obtained from the reactor were assessed for their toxicity using an acute test with Lactuca sativa L. seeds. Results suggested that the treated solution was less toxic than the parent solution, because neither inhibition of lettuce germination nor effects in root and hypocotyl lengths were observed. Therefore, we provide evidence that Brassica napus hairy roots could be effectively used to detoxify solutions containing 2,4-DCP and they have considerable potential for a large scale removal of this pollutant. Thus, this study could help to design a method for continuous and safe treatment of effluents containing chlorophenols.

  1. Scale up of 2,4-dichlorophenol removal from aqueous solutions using Brassica napus hairy roots

    International Nuclear Information System (INIS)

    Angelini, Vanina A.; Orejas, Joaquin; Medina, Maria I.; Agostini, Elizabeth

    2011-01-01

    Research highlights: →B. napus hairy roots were effectively used for a large scale removal of 2,4-DCP. → High removal efficiencies were obtained (98%) in a short time (30 min). → Roots were re-used for six consecutive cycles with high efficiency. → Post removal solutions showed no toxicity. → This method could be used for continuous and safe treatment of phenolic effluents. - Abstract: Chlorophenols are harmful pollutants, frequently found in the effluents of several industries. For this reason, many environmental friendly technologies are being explored for their removal from industrial wastewaters. The aim of the present work was to study the scale up of 2,4-dichlorophenol (2,4-DCP) removal from synthetic wastewater, using Brassica napus hairy roots and H 2 O 2 in a discontinuous stirred tank reactor. We have analyzed some operational conditions, because the scale up of such process was poorly studied. High removal efficiencies were obtained (98%) in a short time (30 min). When roots were re-used for six consecutive cycles, 2,4-DCP removal efficiency decreased from 98 to 86%, in the last cycle. After the removal process, the solutions obtained from the reactor were assessed for their toxicity using an acute test with Lactuca sativa L. seeds. Results suggested that the treated solution was less toxic than the parent solution, because neither inhibition of lettuce germination nor effects in root and hypocotyl lengths were observed. Therefore, we provide evidence that Brassica napus hairy roots could be effectively used to detoxify solutions containing 2,4-DCP and they have considerable potential for a large scale removal of this pollutant. Thus, this study could help to design a method for continuous and safe treatment of effluents containing chlorophenols.

  2. Solution of heat removal from nuclear reactors by natural convection

    Directory of Open Access Journals (Sweden)

    Zitek Pavel

    2014-03-01

    Full Text Available This paper summarizes the basis for the solution of heat removal by natural convection from both conventional nuclear reactors and reactors with fuel flowing coolant (such as reactors with molten fluoride salts MSR.The possibility of intensification of heat removal through gas lift is focused on. It might be used in an MSR (Molten Salt Reactor for cleaning the salt mixture of degassed fission products and therefore eliminating problems with iodine pitting. Heat removal by natural convection and its intensification increases significantly the safety of nuclear reactors. Simultaneously the heat removal also solves problems with lifetime of pumps in the primary circuit of high-temperature reactors.

  3. Investing in Energy Efficiency. Removing the Barriers

    International Nuclear Information System (INIS)

    2004-01-01

    Investing in improving energy efficiency has the clear advantages of reducing energy costs, improving security of supply and mitigating the environmental impacts of energy use. And still, many viable opportunities for higher energy efficiency are not tapped because of the existence of numerous barriers to such investments. These lost opportunities imply costs to the individual energy consumers and to the society as a whole and they are particularly important in economies in transition. This report identifies various types of barriers for making energy efficiency investments (be they of legal, administrative, institutional or financial nature), mainly in buildings, district heating and efficient lighting. The role of various bodies and organisations for the facilitation of energy efficiency investments is analysed, from public authorities and regulators to banks and international financing institutions

  4. Phosphorous removal from aqueous solution can be enhanced through the calcination of lime sludge.

    Science.gov (United States)

    Bal Krishna, K C; Niaz, Mohamed R; Sarker, Dipok C; Jansen, Troy

    2017-09-15

    Water treatment plants generate an enormous amount of the sludge which is normally treated as waste. In the recent past, many investigations have been focused on developing an economical adsorbent using water treatment sludge to remove phosphorous (P) from aqueous solutions. However, the great extents of the studies have been limited in the use of alum- and iron-based sludges. This study, therefore, investigated the P removal performance of the calcined lime sludge. Calcined lime sludge at 700 °C significantly enhanced the P removal efficiency whereas marginal improvement was noted when the sludge calcined at 400 °C was tested. With increase P removal efficiency, final pH values of the solution also significantly increased. P removal efficiency of the calcined sludge decreased with increasing the initial P concentrations. However, the removal efficiency could be improved by increasing the weight of the sludge. Further analysis demonstrated that P removal trend followed both pseudo-second order and diffusion-chemisorption kinetics signifying the P removal is potentially due to a multi-mechanistic reaction in which, the process is controlled by intra-particle diffusion followed by chemisorptions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Experimental Investigation of Phenanthrene Pollutant Removal Efficiency for Contaminated Sandy Soil by Enhanced Soil Washing

    Directory of Open Access Journals (Sweden)

    Saif salah Alquzweeni

    2016-12-01

    Full Text Available Polycyclic aromatic hydrocarbons (PAHs are environmental concerns that must be removed to acceptable level. This research assesses two agents (Na2EDTA and SDS to remediate contaminated sandy soil, spiked with 500mg/kg phenanthrene. Five sets of experiments (batch are applied to investigate the optimal of five influencing factors on soil remediation: Na2EDTA-SDS concentration, liquid/Solid ratio, stirring speed, pH value of flushing solution and mixing time. The results of batch experiments showed that SDS has high phenanthrene removal efficiency (90%, while Na2EDTA shows no phenanthrene removal. pH has no effect on phenanthrene removal. To study the influence of flow rates on the removal efficiency of contaminants, two column tests with hydraulic gradient of 0.2 and 1.2 conducted by SDS solution. The results illustrate that high phenanthrene removal from soil obtained by 1.2 hydraulic gradient condition. The SDS flushing solution removed approximately 69% and 81% of phenanthrene from soil under low and high hydraulic gradients, respectively. It was concluded that phenanthrene removal depend on surfactant micelles formation. Overall, the study showed that soil flushing removal efficiency for contaminants depends on the flushing agents selectivity and affinity to the contaminants and the condition of hydraulic gradient.

  6. Copper removal from aqueous solution using Aspergillus niger mycelia in free and polyurethane-bound form

    Energy Technology Data Exchange (ETDEWEB)

    Tsekova, K.; Ilieva, S. [Inst. of Microbiology, Bulgarian Academy of Sciences, Sofia (Bulgaria)

    2001-07-01

    This study assesses the ability of mycelia of Aspergillus niger B-77 (both free and immobilized on polyurethane foam) to remove copper from single-ion solution. All experiments were conducted using 0.5 mM solutions of CuSO{sub 4}.5H{sub 2} O. Mycelia immobilized on polyurethane foam cells showed a three-fold increase in uptake, compared with that of free cells. The efficiency of copper removal (mg Cu{sup 2+} removed/mg Cu{sup 2+} added) in a column system reached more than 99% before the break-through point was attained. (orig.)

  7. Effect of garlic solution to Bacillus sp. removal

    Science.gov (United States)

    Zainol, N.; Rahim, S. R.

    2018-04-01

    Biofilm is a microbial derived sessile community characterized by cells that are irreversibly attached to a substratum or interface to each other, embedded in a matrix of extracellular polymeric substances that they have produced. Bacillus sp. was used as biofilm model in this study. The purpose of this study is to determine the effect of Garlic solution in term of ratio of water and Garlic solution (W/G) and ratio of Garlic solution to Bacillus sp. (GS/B) on Bacillus sp removal. Garlic solution was used to remove Bacillus sp. In this study, Garlic solution was prepared by crushing the garlic and mixed it with water. the Garlic solution was added into Bacillus sp. mixture and mixed well. The mixture then was spread on nutrient agar. The Bacillus sp. weight on agar plate was measured by using dry weight measurement method. In this study, initially Garlic solution volume and Garlic solution concentration were studied using one factor at time (OFAT). Later two-level-factorial analysis was done to determine the most contributing factor in Bacillus sp. removal. Design Expert software (Version 7) was used to construct experimental table where all the factors were randomized. Bacilus sp removal was ranging between 42.13% to 99.6%. The analysis of the results showed that at W/G of 1:1, Bacillus sp. removal increased when more Garlic solution was added to Bacillus sp. Effect of Garlic solution to Bacillus sp. will be understood which in turn may be beneficial for the industrial purpose.

  8. Removal of Methylene Blue from aqueous solution using spent bleaching earth

    Science.gov (United States)

    Saputra, E.; Saputra, R.; Nugraha, M. W.; Irianty, R. S.; Utama, P. S.

    2018-04-01

    The waste from industrial textile waste is one of the environmental problems, it is required effective and efficient processing. In this study spent bleaching earth was used as absorbent. It was found that the absorbent was effective to remove methylene blue from aqueous solution with removal efficiency 99.97 % in 120 min. Several parameters such as pH, amount of absorbent loading, stirring speed are found as key factor influencing removal of methylene blue. The mechanism of adsorption was also studied, and it was found that Langmuir isotherm fitted to data of experiment with adsorption capacity 0.5 mg/g.

  9. The color removal of dye wastewater by magnesium chloride/red mud (MRM) from aqueous solution.

    Science.gov (United States)

    Wang, Qi; Luan, Zhaokun; Wei, Ning; Li, Jin; Liu, Chengxi

    2009-10-30

    In this study, the MgCl2/red mud system (MRM) was used to investigate the color removal efficiency of dye solutions. Parameters such as the effect of the dosage of red mud (RM) and MgCl2 have been studied. The effect of pH on the conversion rate of Mg2+ has also been studied. The color removal efficiency of MRM was compared with that of PAC/RM and PAC/NaOH. Meanwhile, the color removal efficiency of RM was compared with that of NaOH. The results show that the MRM system can remove more than 98% of the coloring material at a dosage of 25 g RM/L dye solution and a volume of 1.5 mL MgCl2/L dye solution in the decolorization process of reactive dye, acid dye and direct dye. The color removal efficiency was better than PAC/RM and PAC/NaOH system. The adsorption data have been analyzed using Langmuir and Freundlich isotherms. The results indicated that both models provide the best correlation of the experimental data. The decolorization mechanism of MRM was discussed, too. The MRM system was a viable alternative to some of the more conventional forms of chemical treatment of dye solutions and also provided another way to make use of industrial waste red mud.

  10. Antimony removal from aqueous solutions using Zirconium hydroxide

    International Nuclear Information System (INIS)

    Petrescu, D.; Velciu, L.; Bucur, C.

    2016-01-01

    In this paper it is presented an experimental test for non-radioactive antimony removal from aqueous solutions using zirconium hydroxide powder. Also, it was studied how the temperature and pH influences antimony adsorption onto zirconium hydroxide surface. After the adsorption, solutions were filtered on Cellulose Mixed Ester Membrane with 0.2 μm pore size to remove the zirconium powder and then the aqueous solutions were sent to Inductively Coupled Plasma Optic Emission Spectrometry (ICP-OES) for quantitative analysis of Sb. Zirconium hydroxide powders were examined by optical microscopy. For the solutions that were tested at pH 4.5 and 10.2 the antimony concentration dropped below the detection limit of ICP-OES device, proof of antimony adsorption on zirconium hydroxide. Also, for the other tested solutions which had pH=12 the antimony concentration reduced with 77% and 80%. The temperature had no influence upon adsorption mechanism. (authors)

  11. Temperature dependent fission product removal efficiency due to pool scrubbing

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, Shunsuke, E-mail: suchida@iae.or.jp [Institute of Applied Energy, 1-14-2, Nishi-Shimbashi, Minato-ku, Tokyo 105-0003 (Japan); Itoh, Ayumi; Naitoh, Masanori; Okada, Hidetoshi; Suzuki, Hiroyuki [Institute of Applied Energy, 1-14-2, Nishi-Shimbashi, Minato-ku, Tokyo 105-0003 (Japan); Hanamoto, Yukio [KAKEN, Inc., 1044, Hori-machi, Mito 310-0903 (Japan); Osakabe, Masahiro [Tokyo University of Marine Science & Technology, Koutou-ku, Tokyo 135-8533 (Japan); Fujikawa, Masahiro [Japan Broadcasting Corporation, 2-2-1, Jinnan, Shibuya-ku, Tokyo 150-8001 (Japan)

    2016-03-15

    Highlights: • Pool temperature effects on the FP removal were not clearly concluded in the previous publications. • It was confirmed that the removal efficiency decreased with temperature around the boiling point. • A modified empirical formula for FP removal was proposed as a function of sub-cooling temperature. • DF could be predicted with an accuracy within a factor of 2 with the proposed formula. - Abstract: The wet-well of boiling water reactors plays important roles not only to suppress the pressure in the primary containment vessel due to steam scrubbing effects during severe accidents but also to mitigate release of radioactive fission products (FP), aerosols and particulates, into the environment. The effects of steam scrubbing in the wet-well on FP removal have been well studied and reported by changing major parameters determining the removal efficiencies, e.g., aerosol diameters, submergence (depth of scrubbing nozzles) and steam/non-condensable gas volume fraction. Unfortunately, the effects of pool temperature on the FP removal were not clearly concluded in the previous publications, though it would be easily expected that boiling in the pool resulted in reduced aerosol removal efficiency. In order to determine the temperature effects on FP removal efficiency, amounts of cesium in aerosols released from scrubbing pool were measured by changing pool temperature in mini and medium scale scrubbing experiments, and then, it was confirmed that the removal efficiency clearly decreased with temperature around the boiling point. Then, a modified empirical formula to express the FP removal around the boiling point temperature was proposed as a function of sub-cooling temperature by applying the effective steam volume fraction, which was designated as the volume ratio of condensed steam in the pool versus the sum of input steam and non-condensable gas. By comparing the measured removal efficiency with the calculated, it was validated that the

  12. Temperature dependent fission product removal efficiency due to pool scrubbing

    International Nuclear Information System (INIS)

    Uchida, Shunsuke; Itoh, Ayumi; Naitoh, Masanori; Okada, Hidetoshi; Suzuki, Hiroyuki; Hanamoto, Yukio; Osakabe, Masahiro; Fujikawa, Masahiro

    2016-01-01

    Highlights: • Pool temperature effects on the FP removal were not clearly concluded in the previous publications. • It was confirmed that the removal efficiency decreased with temperature around the boiling point. • A modified empirical formula for FP removal was proposed as a function of sub-cooling temperature. • DF could be predicted with an accuracy within a factor of 2 with the proposed formula. - Abstract: The wet-well of boiling water reactors plays important roles not only to suppress the pressure in the primary containment vessel due to steam scrubbing effects during severe accidents but also to mitigate release of radioactive fission products (FP), aerosols and particulates, into the environment. The effects of steam scrubbing in the wet-well on FP removal have been well studied and reported by changing major parameters determining the removal efficiencies, e.g., aerosol diameters, submergence (depth of scrubbing nozzles) and steam/non-condensable gas volume fraction. Unfortunately, the effects of pool temperature on the FP removal were not clearly concluded in the previous publications, though it would be easily expected that boiling in the pool resulted in reduced aerosol removal efficiency. In order to determine the temperature effects on FP removal efficiency, amounts of cesium in aerosols released from scrubbing pool were measured by changing pool temperature in mini and medium scale scrubbing experiments, and then, it was confirmed that the removal efficiency clearly decreased with temperature around the boiling point. Then, a modified empirical formula to express the FP removal around the boiling point temperature was proposed as a function of sub-cooling temperature by applying the effective steam volume fraction, which was designated as the volume ratio of condensed steam in the pool versus the sum of input steam and non-condensable gas. By comparing the measured removal efficiency with the calculated, it was validated that the

  13. Removal of heavy metals from synthetic solution by electrocoagulation

    Directory of Open Access Journals (Sweden)

    Mohamed Ilou

    2016-05-01

    Full Text Available The objective of this work concerns the optimization of the operating conditions for the removal of heavy metals from synthetic solution by Electrocoagulation (EC. To reach this purpose, we prepared a synthetic wastewater containing certain heavy metals (Ni, Cu, Zn, Fe and Pb to study the influence of various parameters (conductivity, pH, time of electrolysis, current density and the initial concentration of the metal on the rate of removal of these metals. The results show that this rate of removal can reach 99.9 % in the following optimal conditions: pH included between 6 and 8 and a density of the current of 1~1.5A / dm2. This study shows that it is possible to remove metals in aqueous solution by the technique of electrocoagulation. 

  14. Optimizing Electrocoagulation Process for the Removal of Nitrate From Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Dehghani

    2016-01-01

    Full Text Available Background High levels of nitrate anion are frequently detected in many groundwater resources in Fars province. Objectives The present study aimed to determine the removal efficiency of nitrate from aqueous solutions by electrocoagulation process using aluminum and iron electrodes. Materials and Methods A laboratory-scale batch reactor was conducted to determine nitrate removal efficiency using the electrocoagulation method. The removal of nitrate was determined at pH levels of 3, 7, and 11, different voltages (15, 20, and 30 V, and operation times of 30, 60, and 75 min, respectively. Data were analyzed using the SPSS software version 16 (Chicago, Illinois, USA and Pearson’s correlation coefficient was used to analyze the relationship between the parameters. Results Results of the present study showed that the removal efficiency was increased from 27% to 86% as pH increased from 3 to 11 at the optimal condition of 30 V and 75 min operation time. Moreover, by increasing the reaction time from 30 V to 75 min the removal efficiency was increased from 63% to 86%, respectively (30 V and pH = 11. Pearson’s correlation analysis showed that there was a significant relationship between removal efficiency and voltage and reaction time as well (P < 0.01. Conclusions In conclusion, the electrocoagulation process can be used for removing nitrate from water resources because of high efficiency, simplicity, and relatively low cost.

  15. Ion exchange removal of technetium from salt solutions

    International Nuclear Information System (INIS)

    Walker, D.D.

    1983-01-01

    Ion exchange methods for removing technetium from waste salt solutions have been investigated by the Savannah River Laboratory (SRL). These experiments have shown: Commercially available anion exchange resins show high selectivity and capacity for technetium. In column runs, 150 column volumes of salt solution were passed through an ion exchange column before 50% 99 Tc breakthrough was reached. The technetium can be eluted from the resin with nitric acid. Reducing resins (containing borohydride) work well in simple hydroxide solutions, but not in simulated salt solutions. A mercarbide resin showed a very high selectivity for Tc, but did not work well in column operation

  16. Simultaneous removal of SO2, NO and Hg0 from flue gas by ferrate (VI) solution

    International Nuclear Information System (INIS)

    Zhao, Yi; Han, Yinghui; Guo, Tianxiang; Ma, Tianzhong

    2014-01-01

    Simultaneously removing SO 2 , NO and Hg 0 from flue gas was examined by ferrate (VI) solution at a bubbling reactor. The removal efficiencies of 100% for SO 2 , 64.8% for NO and 81.4% for Hg 0 were achieved respectively, under the optimum experimental conditions, in which concentration of ferrate (VI) solution was 0.25 mmol/L, solution pH was 8.0, flue gas flow rate was 1 L/min and reaction temperature was 320 K. Based on the discussions of the ferrate (VI) solution characteristics, the comparisons of the standard electrode potential (E 0 ) of ferrate (VI) solution with E 0 values of reactant, and the analysis of the reaction products, a mechanism of simultaneous removal was proposed. In the process of simultaneous removal, FeO 4 2− and HFeO 4 − as the dominant species of ferrate (VI), could rapidly oxidize SO 2 , NO, and Hg 0 into SO 4 2− , NO 3 − and Hg 2+ . - Highlights: • Prepared ferrate (VI) absorbent has excellent property of removing SO 2 , NO and Hg 0 . • 100% of SO 2 , 63.8% of NO and 83.6% of Hg 0 were simultaneously removed. • The simultaneous removal mechanism of SO 2 , NO and Hg 0 was proposed

  17. Photocatalyzed removal of lead ion from lead-chelator solution

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Young Hyun; Na, Jung Won; Sung, Ki Woung [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1994-07-01

    The present study was undertaken to examine the influence of such chelating agents on the ease and speed of photocatalyzed metal removal and deposition. With excess EDTA, the free EDTA competes with Pb for oxidation, and at a ten fold excess, no lead oxidation (hence removal) occurs. With insufficient EDTA, the corresponding initial concentration of Pb-EDTA is decreased; after its destruction, the remaining Pb{sup 2+} is removed more slowly, at rates found with lead nitrate solution. The net result is that the maximum rate of lead deposition occurs at the stoichiometric ratio of 1:1 EDTA : Pb{sup 2+}.

  18. Removal of uranium from ammonium nitrate solution by nanofiltration

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Runci; Yuan, Zhongwei; Yan, Taihong; Zheng, Weifang [China Institute of Atomic Energy, Beijing (China). Dept. of Radiochemistry

    2017-07-01

    Two types of nanofiltration membranes were tested to remove uranium dissolved in ammonium nitrate solution, and the influence of operating parameters as transmembrane pressure, tangential velocity and feed temperature was investigated. Experimental results showed NF270 membrane can reject more than 96% uranium and allow most (90% min) ammonium nitrate solution passed by, and with a permeate flux of 60 L/(m{sup 2}.h). Nanofiltration seems to be a promising technology for the removal of uranium and recovery of ammonium nitrate simultaneously.

  19. Utilization of poplar wood sawdust for heavy metals removal from model solutions

    Directory of Open Access Journals (Sweden)

    Demcak Stefan

    2017-06-01

    Full Text Available Some kinds of natural organic materials have a potential for removal of heavy metal ions from wastewater. It is well known that cellulosic waste materials or by-products can be used as cheap adsorbents in chemical treatment process. In this paper, poplar wood sawdust were used for removal of Cu(II, Zn(II and Fe(II ions from model solutions with using the static and dynamic adsorption experiments. Infrared spectrometry of poplar wood sawdust confirmed the presence of the functional groups which correspond with hemicelluloses, cellulose and lignin. At static adsorption was achieved approximately of 80 % efficiency for all treated model solutions. Similar efficiency of the adsorption processes was reached after 5 min at dynamic condition. The highest efficiency of Cu(II removal (98 % was observed after 30 min of dynamic adsorption. Changes of pH values confirmed a mechanism of ion exchange on the beginning of the adsorption process.

  20. EFFICIENCY OF DOMESTIC REVERSE OSMOSIS IN REMOVAL OF TRIHALOMETHANES FROM DRINKING WATER

    Directory of Open Access Journals (Sweden)

    S. Mazloomi ، R. Nabizadeh ، S. Nasseri ، K. Naddafi ، S. Nazmara ، A. H. Mahvi

    2009-10-01

    Full Text Available The reaction of disinfectants with natural organic matters existing in water lead to the formation of Disinfection By-Products. Potentially hazardous and carcinogenic characteristics of trihalomethanes (THMs are recognized. Thus removal of THMs or its precursors are necessary for human health. The aim of this study was to study the efficiency of domestic reverse osmosis (RO in removal of trihalomethanes from drinking water. A pilot scale of RO system with Polyamide membrane as Spiral-Wound, Tape wrapping module was used. Feed solution was made by using of pure chloroform. The samples containing chloroform were analyzed using a gas chromatograph equipped with a flame ionization detector. By increasing the flow, the removal rate of chloroform decreased and with declining removal of EC, the removal of chloroform declined too. In this research, at the worst condition, the efficiency of the pilot scale reverse osmosis reached to 80 % removal of chloroform.

  1. Dust particle removal efficiency of a venturi scrubber

    International Nuclear Information System (INIS)

    Ali, Majid; Yan, Changqi; Sun, Zhongning; Gu, Haifeng; Mehboob, Khurram

    2013-01-01

    Highlights: ► Experimental and theoretical study of dust removal efficiency in venturi scrubber. ► Dust removal efficiency 99.5% is achieved at throat gas velocity 220 m/s. ► Results obtained from mathematical model concur well with experimental results. - Abstract: The venturi scrubber is one of the most efficient gas cleaning devices to remove the contaminated particles from gaseous stream during severe accident in nuclear power plant. This study is focused on the dust particle removal efficiency of the venturi scrubber experimentally and theoretically. The venturi scrubber encapsulates the dust particles in petite water droplets flowing into it. The water injected into the scrubber is in the form of water film. The study investigates the removal efficiency of venturi scrubber for throat gas velocities of 130, 165 and 200 m/s and liquid flow rates 0.3–1 m 3 /h, whereas dust concentration ranges between 0.1 and 1 g/m 3 . The hydrophobic titanium dioxide (TiO 2 ) particles having density 4.23 g/cm 3 and mean diameter of 1 μm are used as dust particles in this research. Filtration technique is used to measure the concentration of dust particles at inlet and outlet. Experimental results show that the removal efficiency is higher with the increase of throat gas velocity and liquid flow rate. A mathematical model is employed for the verification of experimental results. The model concurs well with the experimental results

  2. IODINE REMOVAL EFFICIENCY IN NON-SUBMERGED AND SUBMERGED SELF-PRIMING VENTURI SCRUBBER

    OpenAIRE

    MAJID ALI; YAN CHANGQI; SUN ZHONGNING; GU HAIFENG; WANG JUNLONG; KHURRAM MEHBOOB

    2013-01-01

    The objective of this conducted research is to study the iodine removal efficiency in a self-priming venturi scrubber for submerged and non-submerged operating conditions experimentally and theoretically. The alkaline solution is used as an absorbent, which is prepared by dissolving sodium hydroxide (NaOH) and sodium thiosulphate (Na2S2O3) in water to remove the gaseous iodine (I2) from the gas. Iodine removal efficiency is examined at various gas flow rates and inlet concentrations of iodine...

  3. Investigation of Phenol Removal by Proxy-Electrocoagulation Process with Iron Electrodes from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Ali Assadi

    2017-09-01

    Full Text Available Background: Phenol as an aromatic hydroxyl compound are considered as a priority pollutant. Because of their stability, solubility in water and high toxicity had health important. Methods: In the present experimental study, electrocoagulation reactor by iron electrodes are used in the presence of hydrogen peroxide to phenol removing from aqueous solutions. Effects of variables including H2O2 dosage, reaction time, pH, current density and initial phenol concentration were evaluated to estimate the efficiency of the process. Results: The results showed that pH and H2O2 have the most important role in the removal of phenol. Increasing of H2O2 concentrations from 0.0125 to 0.025 M increased removal efficiency from 74% to 100%. Maximum removal was achieved at pH=3. However, increasing the pH to 9 lead to reducing removal efficiency to 9.8%. Also, by increasing of current density removal efficiency was increased. But with increasing initial concentration of phenol removal efficiency was reduced. Conclusion: Proxy-electrocoagulation process as an effective and robust process can be used for handling of phenol containing wastewater.

  4. Removal of Acid Red 18 dye from Aqueous Solutions Using Nanoscale Zero-Valent Iron

    Directory of Open Access Journals (Sweden)

    Ahmad Reza Yari

    2015-08-01

    Full Text Available Background and Purpose:Organic dyes with a complex structure are often toxic, carcinogenic, mutagenic, non-biodegradation and stable in the environment and if released to the environment without treatment can endanger the environment and human health. The aim was to evaluate the performance nanoscalezero-valent iron (NZVI in the removal of dye acid red 18 (AR18 from aqueous solutions. Materials and Methods:This study was conducted at the laboratory scale. In this study, the removal efficiency of AR18 from a synthetic solution by NZVI was investigated. As well as the effect of solution pH, dye concentration, the concentration of NZVI and contact time in decolorization efficiency was investigated. Results:The results show that in pH = 3, contact time of 80 minutes, dye concentration of 25 mg/l and concentration of NZVI of 2 g/l, the removal efficiency was about 94%. Conclusion:According to the results of experiments, NZVI has high efficiency in removal of AR18 from aqueous solution.

  5. Removal of perfluoroalkyl sulfonates (PFAS) from aqueous solution using permanently confined micelle arrays (PCMAs)

    KAUST Repository

    Wang, Fei; Lu, Xingwen; Shih, Kaimin; Wang, Peng; Li, Xiaoyan

    2014-01-01

    within 5 min. The pH and salts in solution are found to have limited effects on sorption of PFOS on the new sorbent, and regeneration experiments revealed that PFAS removal efficiencies by the PCMAs did not decrease after 5 cycle regenerations. The high

  6. Arsenic removal from alkaline leaching solution using Fe (III) precipitation.

    Science.gov (United States)

    Wang, Yongliang; Lv, Cuicui; Xiao, Li; Fu, Guoyan; Liu, Ya; Ye, Shufeng; Chen, Yunfa

    2018-02-02

    The alkaline leaching solution from arsenic-containing gold concentrate contains a large amount of arsenate ions, which should be removed because it is harmful to the production process and to the environment. In this study, conventional Fe (III) precipitation was used to remove arsenic from the leaching solution. The precipitation reaction was carried out at the normal temperature, and the effects of pH value and Fe/As ratio on the arsenic removal were investigated. The results show that the removal rate of arsenic is distinctive at different pH values, and the effect is best within the pH range of 5.25-5.96. The removal rate can be further increased by increasing the ratio of Fe/As. When the pH = 5.25-5.96 and Fe/As > 1.8, the arsenic in the solution can be reduced to below 5 mg/L. However, the crystallinity of ferric arsenate is poor, and the particle size is small, most of which is about 1 μm. The leaching toxicity test shows the leaching toxicity of precipitates gradually decreased by the increase of Fe/As. The precipitates can be stored safely as the ratio of Fe/As exceeded 2.5.

  7. A quantitative comparison between electrocoagulation and chemical coagulation for boron removal from boron-containing solution

    International Nuclear Information System (INIS)

    Yilmaz, A. Erdem; Boncukcuoglu, Recep; Kocakerim, M. Muhtar

    2007-01-01

    This paper provides a quantitative comparison of electrocoagulation and chemical coagulation approaches based on boron removal. Electrocoagulation process delivers the coagulant in situ as the sacrificial anode corrodes, due to a fixed current density, while the simultaneous evolution of hydrogen at the cathode allows for pollutant removal by flotation. By comparison, conventional chemical coagulation typically adds a salt of the coagulant, with settling providing the primary pollutant removal path. Chemical coagulation was carried out via jar tests using aluminum chloride. Comparison was done with the same amount of coagulant between electrocoagulation and chemical coagulation processes. Boron removal obtained was higher with electrocoagulation process. In addition, it was seen that chemical coagulation has any effect for boron removal from boron-containing solution. At optimum conditions (e.g. pH 8.0 and aluminum dose of 7.45 g/L), boron removal efficiencies for electrocoagulation and chemical coagulation were 94.0% and 24.0%, respectively

  8. A quantitative comparison between electrocoagulation and chemical coagulation for boron removal from boron-containing solution

    Energy Technology Data Exchange (ETDEWEB)

    Yilmaz, A. Erdem [Atatuerk University, Faculty of Engineering, Department of Environmental Engineering, 25240 Erzurum (Turkey)], E-mail: aerdemy@atauni.edu.tr; Boncukcuoglu, Recep [Atatuerk University, Faculty of Engineering, Department of Environmental Engineering, 25240 Erzurum (Turkey); Kocakerim, M. Muhtar [Atatuerk University, Faculty of Engineering, Department of Chemical Engineering, 25240 Erzurum (Turkey)

    2007-10-22

    This paper provides a quantitative comparison of electrocoagulation and chemical coagulation approaches based on boron removal. Electrocoagulation process delivers the coagulant in situ as the sacrificial anode corrodes, due to a fixed current density, while the simultaneous evolution of hydrogen at the cathode allows for pollutant removal by flotation. By comparison, conventional chemical coagulation typically adds a salt of the coagulant, with settling providing the primary pollutant removal path. Chemical coagulation was carried out via jar tests using aluminum chloride. Comparison was done with the same amount of coagulant between electrocoagulation and chemical coagulation processes. Boron removal obtained was higher with electrocoagulation process. In addition, it was seen that chemical coagulation has any effect for boron removal from boron-containing solution. At optimum conditions (e.g. pH 8.0 and aluminum dose of 7.45 g/L), boron removal efficiencies for electrocoagulation and chemical coagulation were 94.0% and 24.0%, respectively.

  9. Lanthanum-modified bentonite: potential for efficient removal of phosphates from fishpond effluents.

    Science.gov (United States)

    Kurzbaum, Eyal; Raizner, Yasmin; Cohen, Oded; Rubinstein, Guy; Bar Shalom, Oded

    2017-06-01

    Adsorption has been suggested as an effective method for removing phosphates from agricultural wastewater effluents that contain relatively high phosphate concentrations. The present study focused on the use of a bentonite-lanthanum clay (Phoslock ® ) for reducing the dissolved phosphate concentration in fishpond effluents. Batch experiments with synthetic phosphate-spiked solutions and with fishpond effluents were performed in order to determine adsorption equilibrium isotherms and kinetics as well as to determine the efficiency of Phoslock ® in removing phosphate from these solutions. In the synthetic phosphate-spiked solution, the mean maximum phosphate adsorption capacity was 92 mg Phoslock ® /mg phosphate removal. A ratio of 50, 100, and 200 mg Phoslock ® /mg phosphate removal was found for complete phosphate removal from the fishpond effluents, where higher doses of Phoslock ® led to a faster removal rate (94% removal within the first 150 min). These results show that bentonite-lanthanum clay can be employed for designing a treatment process for efficient phosphate removal from fishpond effluents.

  10. Removal of phosphate and nitrate from aqueous solution using ...

    African Journals Online (AJOL)

    The aim of the present study was the removal of phosphate and nitrate by sodium alginate seagrass (Cymodocea rotundata) beads from aqueous solutions. The adsorption characteristics of phosphate and nitrate on the seagrass beads were optimized under different operational parameters like adsorbent dosage, initial ...

  11. Removal of Hexavalent Chromium from Aqueous Solutions using ...

    African Journals Online (AJOL)

    The hexavalent chromium exists in aquatic media as water soluble complex anions and persist. These are concentrated in industrial waste water especially from the tannery industries and release of effluents from industries adversely affects the environment. The removal of heavy metals from aqueous solutions is carried ...

  12. Biosorptive removal of cobalt (II) ions from aqueous solution by ...

    African Journals Online (AJOL)

    The objective of this study was to investigate the possibility of using Amaranthus hybridus L. stalk as an alternative to high cost commercial adsorbent materials for the removal of Co (II) from aqueous solution. The experiment was carried out by batch method at 33°C. The influence of pH, contact time and initial metal ion ...

  13. Removal of phosphate and nitrate from aqueous solution using ...

    African Journals Online (AJOL)

    sunny t

    water, 3.5 g of NaCl were dissolved to obtain 3.5 g/l salinity final solution. When the ... The nitrate adsorption was highly pH dependent, which affects the ... adsorption mechanism that the optimum pH for phosphate removal by .... Biosorption of copper(ii) from aqueous ... Accumulation and detoxification of toxic elements by ...

  14. Preparation of magnetic Ni@graphene nanocomposites and efficient removal organic dye under assistance of ultrasound

    International Nuclear Information System (INIS)

    Zhao, Chuang; Guo, Jianhui; Yang, Qing; Tong, Lei; Zhang, Jingwei; Zhang, Jiwei; Gong, Chunhong; Zhou, Jingfang; Zhang, Zhijun

    2015-01-01

    Graphical abstract: Reduced graphene oxide/Ni microspheres, being prepared under ultrasound conditions, exhibit a better removal efficiency to decolorize RhB with ultrasonic-assisted decolorization process. - Highlights: • One-step synthesis of Ni@graphene microspheres under ultrasound conditions. • During the ultrasonic process, graphene oxide was reduced and Ni nanoparticles were formed and anchored on graphene sheets. • The products exhibit excellent performance for fast and efficient removal of dye contaminants. • The nanocomposites can be easily separated from solution by a magnet. - Abstract: In this article, we report a facile one-step synthesis of Ni@graphene nanocomposite microspheres (NGs) in hydrazine hydrate solution under ultrasound conditions. During the ultrasonic process, graphene oxide (GO) was reduced effectively under mild conditions and Ni nanoparticles were simultaneously formed and anchored on graphene sheets, which act as spacers to keep the neighboring sheets separated. The target products exhibit excellent performance for fast and efficient removal of dye contaminants, rhodamine B (RhB) in aqueous solution, under assistance of ultrasound. Finally, the nanocomposites can be easily separated from solution by a magnet. Furthermore, higher content of graphene can be produced under sonication, which facilitates faster and more efficient removal of organic contaminates in the solution. The nanocomposites were also characterized by scanning electron microscopy, Raman spectroscopy, Fourier transformed infrared spectroscopy, X-ray photoelectron spectroscopy, X-ray powder diffraction and thermogravimetric analysis.

  15. Preparation of magnetic Ni@graphene nanocomposites and efficient removal organic dye under assistance of ultrasound

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Chuang; Guo, Jianhui; Yang, Qing; Tong, Lei [Key Laboratory of Ministry of Education for Special Functional Materials, Henan University, Kaifeng 475004 (China); Zhang, Jingwei, E-mail: jwzhang@henu.edu.cn [Key Laboratory of Ministry of Education for Special Functional Materials, Henan University, Kaifeng 475004 (China); Ian Wark Research Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Zhang, Jiwei [Key Laboratory of Ministry of Education for Special Functional Materials, Henan University, Kaifeng 475004 (China); Gong, Chunhong [College of Chemistry and Chemical Engineering, Henan University, Kaifeng 475004 (China); Ian Wark Research Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Zhou, Jingfang, E-mail: jingfang.zhou@unisa.edu.au [Ian Wark Research Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Zhang, Zhijun [Key Laboratory of Ministry of Education for Special Functional Materials, Henan University, Kaifeng 475004 (China)

    2015-12-01

    Graphical abstract: Reduced graphene oxide/Ni microspheres, being prepared under ultrasound conditions, exhibit a better removal efficiency to decolorize RhB with ultrasonic-assisted decolorization process. - Highlights: • One-step synthesis of Ni@graphene microspheres under ultrasound conditions. • During the ultrasonic process, graphene oxide was reduced and Ni nanoparticles were formed and anchored on graphene sheets. • The products exhibit excellent performance for fast and efficient removal of dye contaminants. • The nanocomposites can be easily separated from solution by a magnet. - Abstract: In this article, we report a facile one-step synthesis of Ni@graphene nanocomposite microspheres (NGs) in hydrazine hydrate solution under ultrasound conditions. During the ultrasonic process, graphene oxide (GO) was reduced effectively under mild conditions and Ni nanoparticles were simultaneously formed and anchored on graphene sheets, which act as spacers to keep the neighboring sheets separated. The target products exhibit excellent performance for fast and efficient removal of dye contaminants, rhodamine B (RhB) in aqueous solution, under assistance of ultrasound. Finally, the nanocomposites can be easily separated from solution by a magnet. Furthermore, higher content of graphene can be produced under sonication, which facilitates faster and more efficient removal of organic contaminates in the solution. The nanocomposites were also characterized by scanning electron microscopy, Raman spectroscopy, Fourier transformed infrared spectroscopy, X-ray photoelectron spectroscopy, X-ray powder diffraction and thermogravimetric analysis.

  16. Boron removal from aqueous solutions by activated carbon impregnated with salicylic acid

    International Nuclear Information System (INIS)

    Celik, Z. Ceylan; Can, B.Z.; Kocakerim, M. Muhtar

    2008-01-01

    In this study, the removal of boric acid from aqueous solution by activated carbon impregnated with salicylic acid was studied in batch system. pH, adsorbent amount, initial boron concentration, temperature, shaking rate and salicylic acid film thickness were chosen as parameters. Boron removal efficiencies increased with increasing adsorbent amount, temperature and pH, decreasing initial boron concentration. As thickness of salicylic acid film on activated carbon becomes thin up to 0.088 nm, the efficiency increased, and then, the efficiency decreased with becoming thinner than 0.088 nm of salicylic acid film. Shaking rate was no effect on removal efficiency. In result, it was determined that the use of salicylic acid as an impregnant for activated carbon led to the increase of the amount of boron adsorbed. A lactone ring, being the most appropriate conformation, forms between boric acid and -COOH and -OH groups of salicylic acid

  17. Boron removal from aqueous solutions by activated carbon impregnated with salicylic acid

    Energy Technology Data Exchange (ETDEWEB)

    Celik, Z. Ceylan [Department of Environmental Engineering, Atatuerk University, Faculty of Engineering, Erzurum (Turkey)], E-mail: zcelik@atauni.edu.tr; Can, B.Z. [Department of Environmental Engineering, Atatuerk University, Faculty of Engineering, Erzurum (Turkey); Kocakerim, M. Muhtar [Department of Chemical Engineering, Atatuerk University, Faculty of Engineering, 25240 Erzurum (Turkey)

    2008-03-21

    In this study, the removal of boric acid from aqueous solution by activated carbon impregnated with salicylic acid was studied in batch system. pH, adsorbent amount, initial boron concentration, temperature, shaking rate and salicylic acid film thickness were chosen as parameters. Boron removal efficiencies increased with increasing adsorbent amount, temperature and pH, decreasing initial boron concentration. As thickness of salicylic acid film on activated carbon becomes thin up to 0.088 nm, the efficiency increased, and then, the efficiency decreased with becoming thinner than 0.088 nm of salicylic acid film. Shaking rate was no effect on removal efficiency. In result, it was determined that the use of salicylic acid as an impregnant for activated carbon led to the increase of the amount of boron adsorbed. A lactone ring, being the most appropriate conformation, forms between boric acid and -COOH and -OH groups of salicylic acid.

  18. Process for the removal of radium from acidic solutions containing same

    Science.gov (United States)

    Scheitlin, F.M.

    The invention is a process for the removal of radium from acidic aqueous solutions. In one aspect, the invention is a process for removing radium from an inorganic-acid solution. The process comprises contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple, comparatively inexpensive, and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities throughout the United States. The invention is applicable, for example, to the recovery of /sup 226/Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings.

  19. A study on removal of elemental mercury in flue gas using fenton solution

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yangxian; Wang, Yan; Wang, Qian; Pan, Jianfeng [School of Energy and Power Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013 (China); Zhang, Yongchun [Jiangsu Province Special Equipment Safety Supervision Inspection Institute (Branch of Wuxi), Wuxi 214000 (China); Zhou, Jianfei [School of Energy and Power Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013 (China); Zhang, Jun [Key Laboratory of Energy Thermal Conversion and Control of Ministry of Education, Southeast University, Nanjing 210096 (China)

    2015-07-15

    Highlights: • A novel technique on oxidation of Hg{sup 0} using Fenton was proposed. • The effects of several process parameters on Hg{sup 0} removal were studied. • Products and ·OH in solution were detected. • Reaction mechanism of Hg{sup 0} removal was studied. • Simultaneous removal of Hg{sup 0}, NO and SO{sub 2} was also studied. - Abstract: A novel technique on oxidation-separation of elemental mercury (Hg{sup 0}) in flue gas using Fenton solution in a bubbling reactor was proposed. The effects of several process parameters (H{sub 2}O{sub 2} concentration, Hg{sup 0} inlet concentration, Fe{sup 2+} concentration, solution temperature, solution pH, gas flow) and several flue gas components (NO, SO{sub 2}, O{sub 2}, CO{sub 2}, inorganic ions and particulate matters on Hg{sup 0} removal were studied. The results indicate that H{sub 2}O{sub 2} concentration, Fe{sup 2+} concentration, solution pH and gas flow have great effects on Hg{sup 0} removal. Solution temperature, Hg{sup 0}, NO, SO{sub 2}, CO{sub 3}{sup 2−} and HCO{sub 3}{sup −} concentrations also have significant effects on Hg{sup 0} removal. However, Cl{sup −}, SO{sub 4}{sup 2−}, NO{sub 3}{sup −}, O{sub 2} and CO{sub 2} concentrations only have slight effects on Hg{sup 0} removal. Furthermore, reaction mechanism of Hg{sup 0} removal and simultaneous removal process of Hg{sup 0}, NO and SO{sub 2} were also studied. Hg{sup 0} is removed by oxidation of ·OH and oxidation of H{sub 2}O{sub 2}. The simultaneous removal efficiencies of 100% for SO{sub 2}, 100% for Hg{sup 0} and 88.3% for NO were obtained under optimal test conditions. The results demonstrated the feasibility of Hg{sup 0} removal and simultaneous removal of Hg{sup 0}, SO{sub 2} and NO using Fenton solution in a bubbling reactor.

  20. Enhanced removal of radioactive particles by fluorocarbon surfactant solutions

    International Nuclear Information System (INIS)

    Kaiser, R.; Harling, O.K.

    1993-08-01

    The proposed research addressed the application of ESI's particle removal process to the non-destructive decontamination of nuclear equipment. The cleaning medium used in this process is a solution of a high molecular weight fluorocarbon surfactant in an inert perfluorinated liquid which results in enhanced particle removal. The perfluorinated liquids of interest, which are recycled in the process, are nontoxic, nonflammable, and environmentally compatible, and do not present a hazard to the ozone layer. The information obtained in the Phase 1 program indicated that the proposed ESI process is technically effective and economically attractive. The fluorocarbon surfactant solutions used as working media in the ESI process survived exposure of up to 10 Mrad doses of gamma rays, and are considered sufficiently radiation resistant for the proposed process. Ultrasonic cleaning in perfluorinated surfactant solutions was found to be an effective method of removing radioactive iron (Fe 59) oxide particles from contaminated test pieces. Radioactive particles suspended in the process liquids could be quantitatively removed by filtration through a 0.1 um membrane filter. Projected economics indicate a pre-tax pay back time of 1 month for a commercial scale system

  1. Removal of heavy metals from aqueous solution by Carrot residues

    International Nuclear Information System (INIS)

    Eslamzadeh, T.; Nasernejad, B.; Bonakdar Pour, B.; Zamani, A.; Esmaail-Beygi, M.

    2004-01-01

    The removal of Copper(II), Zinc(II), and Chromium (III) from wastewater by carrot residues was investigated to evaluate cation exchange capacity. The effects of solution P H and co-ions were studied in batch experiments. Adsorption equilibria were initially rapidly established, and then decreased markedly after 10 min. Column experiments were carried out in a glass column filled with carrot residues to evaluate the metal removal capacity. The influences of the feed concentration and feed rate were also studied in order to compare the dynamic capacity for metal binding in different feed concentrations

  2. Removal of ammonia solutions used in catalytic wet oxidation processes.

    Science.gov (United States)

    Hung, Chang Mao; Lou, Jie Chung; Lin, Chia Hua

    2003-08-01

    Ammonia (NH(3)) is an important product used in the chemical industry, and is common place in industrial wastewater. Industrial wastewater containing ammonia is generally either toxic or has concentrations or temperatures such that direct biological treatment is unfeasible. This investigation used aqueous solutions containing more of ammonia for catalytic liquid-phase oxidation in a trickle-bed reactor (TBR) based on Cu/La/Ce composite catalysts, prepared by co-precipitation of Cu(NO(3))(2), La(NO(3))(2), and Ce(NO(3))(3) at 7:2:1 molar concentrations. The experimental results indicated that the ammonia conversion of the wet oxidation in the presence of the Cu/La/Ce composite catalysts was determined by the Cu/La/Ce catalyst. Minimal ammonia was removed from the solution by the wet oxidation in the absence of any catalyst, while approximately 91% ammonia removal was achieved by wet oxidation over the Cu/La/Ce catalyst at 230 degrees C with oxygen partial pressure of 2.0 MPa. Furthermore, the effluent streams were conducted at a liquid hourly space velocity of under 9 h(-1) in the wet catalytic processes, and a reaction pathway was found linking the oxidizing ammonia to nitric oxide, nitrogen and water. The solution contained by-products, including nitrates and nitrites. Nitrite selectivity was minimized and ammonia removal maximized when the feed ammonia solution had a pH of around 12.0.

  3. Affordable Energy-Efficient New Housing Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Chandra, Subrato; Widder, Sarah H.; Bartlett, Rosemarie; McIlvaine, Janet; Chasar, David; Beal, David; Sutherland, Karen; Abbott, , K.; Fonorow, Ken; Eklund, Ken; Lubliner, Michael; Salzberg, Emily; Peeks, B.; Hewes, T.; Kosar, D.

    2012-05-31

    Since 2010, the U.S. Department of Energy’s Building America has sponsored research at PNNL to investigate cost-effective, energy-saving home-building technologies and to demonstrate how high-performance homes can deliver lower utility bills, increased comfort, and improved indoor air quality, while maintaining accessibility for low-income homeowners. PNNL and its contractors have been investigating 1) cost-effective whole-house solutions for Habitat for Humanity International (HFHI) and specific HFH affiliates in hot-humid and marine climates; 2) cost-effective energy-efficiency improvements for heating, ventilation, and air-conditioning (HVAC) systems in new, stick-built and manufactured homes; and 3) energy-efficient domestic hot-water systems.

  4. Application of Activated Carbon for Removal of Arsenic Ions from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    R. Ansari

    2007-01-01

    Full Text Available The activated carbon (AC was used for removal of As(III and As(V ions from aqueous solutions. Sorption experiments were conducted using both batch and column systems. The effect of some important parameters on sorption of these by AC was studied. It was found that among the different factors affecting sorption capacity and efficiency in removal of arsenic from aqueous solutions, the effect of pH and the oxidation state were the most prominent. The optimum pH values for removal of As(III and As(V from aqueous solutions using AC was found 12 and 3 respectively. Impregnation of AC with sulphur contain organic dyes, it is possible to improve As(III uptake considerably.

  5. Removal of perfluoroalkyl sulfonates (PFAS) from aqueous solution using permanently confined micelle arrays (PCMAs)

    KAUST Repository

    Wang, Fei

    2014-12-01

    One new sorbent with permanently confined micelle arrays (PCMAs) has been synthesized to remove PFAS compounds from aquatic solutions. The TEM and SEM studies showed that large particle sizes with lots of macro-pores and highly order hexagonal structure of cylindrical micelle had been formed in the sorbent. The FTIR spectrums demonstrated the formation of Si-O-Si covalent bond in the new material. The kinetic study showed that the sorption of PFOS, PFHxS, and PFBuS by PCMAs reached equilibrium within 5 min. The pH and salts in solution are found to have limited effects on sorption of PFOS on the new sorbent, and regeneration experiments revealed that PFAS removal efficiencies by the PCMAs did not decrease after 5 cycle regenerations. The high capabilities of PCMAs make it a potentially attractive sorbent for the removal of PFCs from aqueous solution.

  6. Evaluation of BTEX and phenol removal from aqueous solution by multi-solute adsorption onto smectite organoclay.

    Science.gov (United States)

    Carvalho, M N; da Motta, M; Benachour, M; Sales, D C S; Abreu, C A M

    2012-11-15

    The removal process of BTEX and phenol was evaluated. The smectite organoclay for single-solute system reached removal was evaluated by adsorption on smectite organoclay adsorbent by kinetic and equilibrium efficiencies between 55 and 90% while was reached between 30 and 90% for multi-solute system at 297 K and pH 9. The Langmuir-Freundlich model was used to fit the experimental data with correlation coefficient between 0.98 and 0.99 providing kinetic and equilibrium parameter values. Phenol and ethylbenzene presented high maximum adsorbed amount, 8.28 and 6.67 mg/g, respectively, compared to the other compounds for single-solute. Toluene and p-xylene presented high values of adsorption constant which indicates a high adsorption affinity of compounds to organoclay surface and high binding energy of adsorption. Phenol presented low kinetic adsorption constant value indicating slow rate of adsorption. Copyright © 2012 Elsevier B.V. All rights reserved.

  7. Removal of phenol from aqueous solution using rice straw as adsorbent

    Science.gov (United States)

    Sarker, Nandita; Fakhruddin, A. N. M.

    2017-06-01

    Phenol is an environmental pollutant; the present study was conducted to examine the adsorption of phenol by rice straw. For this purpose raw (untreated), physically treated (boiled and dried) and thermally treated (heated at 230 °C for 3 h to produce ash) rice straw were selected to determine phenol removal efficiency at different contact times and adsorbent dosages for 1 and Percentage of removal of phenol increased as the adsorbent dose increase. The removal efficiency increase in the order of: raw rice straw ash) rice straw. Langmuir and Freundlich isotherm was developed for 1 and ash) treated rice straw. Freundlich isotherm best fit the equilibrium data for 1 mm thermally treated rice straw. The results showed that thermally treated rice straw (ash) can be developed as a potential adsorbent for phenol removal from aqueous solution.

  8. Using Eggshell in Acid Orange 2 Dye Removal from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Ahmad Reza Yari

    2015-05-01

    Full Text Available Background and purpose: Generated dye wastewater by the textile industry is usually toxic, non-biodegradable and resistant in the environment. Eggshell is one of the inexpensive material and for the reason the vesicular structures can be used as a proper adsorbent for pollutants removal. The aim of this study is to investigate the efficiency of eggshell for removal of acid orange 2 dye from aqueous solution. Materials and Methods: In the experimental study was determined the efficacy of variant variables such as contact time (15, 30, 60, 90 and 120 min, pH (3, 7 and 11, adsorbent dose (10, 25, 50 and 75 g/L, and initial dye concentration (25, 50 and 100 mg/L. The concentration of dye by spectrophotometer ultraviolet/visible in the wavelength 483 nm was examined. Results: The results showed that with increasing contact time and adsorbent dose, the dye removal efficiency was increased, but with increasing pH and initial dye concentration the removal efficiency was decreased. The maximum of removal efficiency of acid orange 2 dye got in the optimum pH: 3, contact time: 90 min, adsorbent dose: 50 g/L and initial dye concentration: 25 mg/L. Adsorption of acid orange 2 dye (R2 = 0.87 follow the Freundlich isotherm. Conclusion: Eggshells can be used as an inexpensive and effective adsorbent for the removal of acid orange 2 dye.

  9. Cr(VI) removal from aqueous solution by dried activated sludge biomass

    International Nuclear Information System (INIS)

    Wu Jun; Zhang Hua; He Pinjing; Yao Qian; Shao Liming

    2010-01-01

    Batch experiments were conducted to remove Cr(VI) from aqueous solution using activated sludge biomass. The effects of acid pretreatment of the biomass, initial pH, biomass and Cr(VI) concentrations on Cr(VI) removal efficiency were investigated. Proton consumption during the removal process and the reducing capacity of sludge biomass were studied. The results show that acid pretreatment could significantly improve Cr(VI) removal efficiency and increase Cr(VI) reducing capacity by 20.4%. Cr(VI) removal was remarkably pH-dependent; lower pH (pH = 1, 2) facilitated Cr(VI) reduction while higher pH (pH = 3, 4) favored sorption of the converted Cr(III). Lower Cr(VI) concentration as well as higher biomass concentration could accelerate Cr(VI) removal. Cr(VI) reduction was not the only reason for proton consumption in the removal process. Pseudo-second-order adsorption kinetic model could successfully simulate Cr(VI) removal except under higher pH conditions (pH = 3, 4).

  10. Removal of Cholera Toxin from Aqueous Solution by Probiotic Bacteria

    Directory of Open Access Journals (Sweden)

    Jussi A. O. Meriluoto

    2012-06-01

    Full Text Available Cholera remains a serious health problem, especially in developing countries where basic hygiene standards are not met. The symptoms of cholera are caused by cholera toxin, an enterotoxin, which is produced by the bacterium Vibrio cholerae. We have recently shown that human probiotic bacteria are capable of removing cyanobacterial toxins from aqueous solutions. In the present study we investigate the ability of the human probiotic bacteria, Lactobacillus rhamnosus strain GG (ATCC 53103 and Bifidobacterium longum 46 (DSM 14583, to remove cholera toxin from solution in vitro. Lactobacillus rhamnosus strain GG and Bifidobacterium longum 46 were able to remove 68% and 59% of cholera toxin from aqueous solutions during 18 h of incubation at 37 °C, respectively. The effect was dependent on bacterial concentration and L. rhamnosus GG was more effective at lower bacterial concentrations. No significant effect on cholera toxin concentration was observed when nonviable bacteria or bacterial supernatant was used.

  11. Effects of operational parameters on the removal of brilliant green dye from aqueous solutions by electrocoagulation

    Directory of Open Access Journals (Sweden)

    Barun Kumar Nandi

    2017-05-01

    Full Text Available This paper presents an experimental study on the removal of brilliant green dye from aqueous solutions in a batch stirred electrocoagulation (EC reactor using iron electrodes. The main objectives of the experiments were to investigate the effects of the various operating parameters, such as current density, inter electrode distance, initial dye concentration, pH of the solution, EC duration and salt (NaCl concentrations on the brilliant green dye removal efficiency from synthetic wastewater containing in batch EC process. The experimental results showed that 99.59% dye removal was observed for initial dye concentration of 100 mg/L with current density of 41.7 A/m2, initial pH of 4.0 at the end of 30 min of operation. It was observed that, an increase in current density, time of operation and decrease in inter electrode distance improved the dye removal efficiency. Optimum pH for highest dye removal was 4.0–10.0. It was also observed that increase in salt (NaCl concentration in the solution reduces the specific electrical energy consumption (SEEC.

  12. Efficiency of water removal from water/ethanol mixtures using supercritical carbon dioxide

    Directory of Open Access Journals (Sweden)

    M. A. Rodrigues

    2006-06-01

    Full Text Available Techniques involving supercritical carbon dioxide have been successfully used for the formation of drug particles with controlled size distributions. However, these processes show some limitations, particularly in processing aqueous solutions. A diagram walking algorithm based on available experimental data was developed to evaluate the effect of ethanol on the efficiency of water removal processes under different process conditions. Ethanol feeding was the key parameter resulting in a tenfold increase in the efficiency of water extraction.

  13. Cadmium Removal from Aqueous Solutions by Ground Pine Cone

    Directory of Open Access Journals (Sweden)

    H Izanloo, S Nasseri

    2005-01-01

    Full Text Available A study on the removal of cadmium ions from aqueous solutions by pine cone was conducted in batch conditions. Kinetic data and equilibrium removal isotherms were obtained. The influence of different experimental parameters such as contact time, initial concentration of cadmium, pine cone mass and particle size, and temperature on the kinetics of cadmium removal was studied. Results showed that the main parameters that played an important role in removal phenomenon were initial cadmium concentration, particle size and pine cone mass. The necessary time to reach equilibrium was between 4 and 7 hours based on the initial concentration of cadmium. The capacity of cadmium adsorption at equilibrium increased with the decrease of pine cone particle size. The capacity of cadmium adsorption at equilibrium by pine cone increased with the quantity of pine cone introduced (1–4 g/L. Temperature in the range of 20-30°C showed a restricted effect on the removal kinetics (13.56 mg/g at 20°C and a low capacity of adsorption about 11.48 mg/g at 30°C. The process followed pseudo second-order kinetics. The cadmium uptake of pine cone was quantitatively evaluated using adsorption isotherms. Results indicated that the Langmuir model gave a better fit to the experimental data in comparison with the Freundlich equation.

  14. Removal of trace Cd2+ from aqueous solution by foam fractionation.

    Science.gov (United States)

    Lu, Jian; Li, Ying; Zhang, Sen; Sun, Yange

    2015-04-09

    In recent years, aqueous foam was known as an efficient technique with high potential on being used to remove heavy metal ions from the polluted water, not only because of the low cost, simple operation, but also ascribed to the high removal efficiency of trace heavy metal ions and would not cause secondary pollution to the environment. In this paper, the removal of Cd(2+) from aqueous solution by aqueous foam stabilized by a kind of novel anionic-nonionic surfactant sodium trideceth-4 carboxylate (AEC) was investigated. The effect of conditions such as surfactant/metal ions molar ratio, surfactant concentration on the removal efficiency was studied. In large concentration range of surfactant, the removal rate was higher than 90%, and could reach up to 99.8% under the optimum conditions. The Zeta potential of gas bubbles in the AEC solutions was determined to verify the combination between the negative charged group heads of surfactant molecules and heavy metal ions, and isothermal titration calorimeter (ITC) determination was utilized to demonstrate the interaction, which helped to understand the mechanisms more clearly. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Removal of dexamethasone from aqueous solution and hospital wastewater by electrocoagulation

    International Nuclear Information System (INIS)

    Arsand, Daniel R.; Kümmerer, Klaus; Martins, Ayrton F.

    2013-01-01

    This study is concerned with the removal of the anti-inflammatory dexamethasone from aqueous solution and hospital wastewater by electrocoagulation. The variation of the toxicity during the electrocoagulation was also studied through experiments that were designed and optimized by means of response surface methodology. The coagulation efficiency was evaluated by measuring the dexamethasone concentration by high performance liquid chromatography coupled to a diode array detector. In addition, variation was evaluated through a Vibrio fischeri test. The results showed an increase in the removal of dexamethasone (up to 38.1%) with a rise of the current applied and a decrease of the inter-electrode distance, in aqueous solutions. The application to hospital effluent showed similar results for the removal of dexamethasone. The main effect of the electrocoagulation was that it removed colloids and reduced the organic load of the hospital wastewater. Regarding the current applied, the calculated energy efficiency was 100%. Without pH adjustment of the aqueous solution or hospital wastewater, the residual aluminum concentration always remained lower than 10 mg L −1 , and, with adjustment (to pH 6.5), lower than 0.30 mg L −1 , at the final stage. No toxicity variation was observed during the electrocoagulation process in aqueous solution, either in the presence or absence of dexamethasone. - Highlights: ► Removal of DEX and organic load from aqueous solution and hospital wastewater by EC ► Evaluation of the toxicity during the removal of DEX by EC ► Suggestion of the EC process as a pretreatment for subsequent processes

  16. Removal of dexamethasone from aqueous solution and hospital wastewater by electrocoagulation

    Energy Technology Data Exchange (ETDEWEB)

    Arsand, Daniel R., E-mail: danielarsand@pelotas.ifsul.edu.br [Chemistry Department, Federal University of Santa Maria, RS (Brazil); Kümmerer, Klaus, E-mail: klaus.kuemmerer@leuphana.de [Institute for Environmental Chemistry, Leuphana University Lüneburg (Germany); Martins, Ayrton F., E-mail: martins@quimica.ufsm.br [Chemistry Department, Federal University of Santa Maria, RS (Brazil)

    2013-01-15

    This study is concerned with the removal of the anti-inflammatory dexamethasone from aqueous solution and hospital wastewater by electrocoagulation. The variation of the toxicity during the electrocoagulation was also studied through experiments that were designed and optimized by means of response surface methodology. The coagulation efficiency was evaluated by measuring the dexamethasone concentration by high performance liquid chromatography coupled to a diode array detector. In addition, variation was evaluated through a Vibrio fischeri test. The results showed an increase in the removal of dexamethasone (up to 38.1%) with a rise of the current applied and a decrease of the inter-electrode distance, in aqueous solutions. The application to hospital effluent showed similar results for the removal of dexamethasone. The main effect of the electrocoagulation was that it removed colloids and reduced the organic load of the hospital wastewater. Regarding the current applied, the calculated energy efficiency was 100%. Without pH adjustment of the aqueous solution or hospital wastewater, the residual aluminum concentration always remained lower than 10 mg L{sup −1}, and, with adjustment (to pH 6.5), lower than 0.30 mg L{sup −1}, at the final stage. No toxicity variation was observed during the electrocoagulation process in aqueous solution, either in the presence or absence of dexamethasone. - Highlights: ► Removal of DEX and organic load from aqueous solution and hospital wastewater by EC ► Evaluation of the toxicity during the removal of DEX by EC ► Suggestion of the EC process as a pretreatment for subsequent processes.

  17. A study on nitrogen removal efficiency of Pseudomonas stutzeri ...

    African Journals Online (AJOL)

    USER

    2010-02-08

    Feb 8, 2010 ... ambient temperature in the reaction system, the efficiency of nitrogen removal was studied. The results ... no reported experiment which has been conducted to ... controlled shaker at 32°C with a 150 r/min rotating speed (Ahn,.

  18. Efficiency of SPIONs functionalized with polyethylene glycol bis(amine) for heavy metal removal

    Energy Technology Data Exchange (ETDEWEB)

    Wanna, Yongyuth, E-mail: yongyuth.wanna@gmail.com [College of KMITL Nanotechnology, King Mongkut' s Institute of Technology Ladkrabang, Chalongkrung Rd., Ladkrabang, Bangkok 10520 (Thailand); Nara Machinery Co., Ltd., 2-5-7, Jonan-Jima, Ohta-ku, Tokyo 143-0002 (Japan); Chindaduang, Anon; Tumcharern, Gamolwan [National Nanotechnology Center (NANOTEC), 111 Thailand Science Park, Pahol Yothin Rd, Klong Luang, Pathum Thani 12120 (Thailand); Phromyothin, Darinee [College of KMITL Nanotechnology, King Mongkut' s Institute of Technology Ladkrabang, Chalongkrung Rd., Ladkrabang, Bangkok 10520 (Thailand); Porntheerapat, Supanit [NECTEC, National Science and Technology Development Agency (NSTDA), 112 Thailand Science Park, Phahonyothin Rd., Khlong Nueng, Khlong Luang, Pathum Thani 12120 (Thailand); Nukeaw, Jiti [College of KMITL Nanotechnology, King Mongkut' s Institute of Technology Ladkrabang, Chalongkrung Rd., Ladkrabang, Bangkok 10520 (Thailand); Hofmann, Heirich [Laboratory of Powder Technology, Ecole Polytechnique Fédérale de Lausanne (Switzerland); Pratontep, Sirapat [College of KMITL Nanotechnology, King Mongkut' s Institute of Technology Ladkrabang, Chalongkrung Rd., Ladkrabang, Bangkok 10520 (Thailand)

    2016-09-15

    Hybrid magnetic nanoparticles based on poly(methylmethacrylate) (PMMA) and super-paramagnetic iron oxide nanopaticles (SPIONs) with selective surface modification has been developed for heavy metal removal by applying external magnetic fields. The nanoparticles were prepared by the emulsion polymerization technique in an aqueous suspension of SPIONs. The hydrolysis of carboxyl functional group was then applied for grafting polyethylene glycol bis(amine)(PEG-bis(amine)) onto the PMMA-coated SPIONs. The morphology, the chemical structure and the magnetic properties of the grafted nanoparticles were investigated. The efficiency of the hybrid nanoparticles for heavy metal removal were conducted on Pb(II), Hg(II), Cu(II) and Co(II) in aqueous solutions.The metal concentration in the solutions after separation by the hybrid nanoparticles was determined by inductively coupled plasma optical emission spectrometer (ICP-OES). The results show the heavy metal uptake ratios of 0.08, 0.04, 0.03, and 0.01 mM per gramme of the grafted SPIONs for Pb(II), Hg(II), Cu(II), and Co(II), respectively. A competitive removal of Cu(II), Pb(II), Co(II) and Hg(II) ions in mixed metal salt solutions has also been studied.The heavy metal removal efficiency of the hybrid nanoparitcles was found to depend on the cation radius, in accordance with capture of metal ions by the amine group. - Highlights: • We synthesis hybrid magnetic nanoparticles for heavy metal removal. • The efficiency of hybrid nanoparticles for heavy metal removal is proposed. • We investigated the characteristic of hybrid nanoparticle. • The heavy metal removal efficiency of the hybrid nanoparticle was founded that depend on the heavy metal cation radius.

  19. Application of Azolla for 2-Chlorophenol and 4-Chrorophenol Removal from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Zazouli

    2013-09-01

    Full Text Available Background and purpose: The 2-chlorophenol (2-CP and 4-chlorophenol (4-CP are phenolic compounds which may have adverse effects on human and environment. Therefore, removing these compounds from water and wastewater is necessary. This study aims to analyze 2-CP and 4-CP removal by using Azolla filiculoides biomass. Materials & Methods: Azolla biomass was sun dried, crushed and sieved to particle sizes ranging 1-2 mm. Then it was treated with 0.1M HCl for 5h followed by washing with distilled water and it was used as adsorbent. The residues concentration of 2-CP and 4-CP was measured by spectrophotometer in λmax of 274 and 280 nm, respectively. Results: The solute removed increases as contact time rises. The equilibrium time for 2-CP and 4-CP is 90 and 75, respectively. The removal efficiency of 4-CP is more than 2-CP. An increase in initial concentration of both compounds can lead to decrease of their removal efficiency. The optimum pH to remove both compounds is 5. The equilibrium data matched best on Freundlich isotherm and the adsorption kinetic model follows pseudo-second model. Conclusion: The results indicated that Azolla is an effective adsorbent for removing 2-CP and 4-CP from water and wastewater.

  20. Removal of Congo red dye from aqueous solutions using a halloysite-magnetite-based composite.

    Science.gov (United States)

    Ferrarini, F; Bonetto, L R; Crespo, Janaina S; Giovanela, M

    2016-01-01

    Adsorption has been considered as one of the most effective methods to remove dyes from aqueous solutions due to its ease of operation, high efficiency and wide adaptability. In view of all these aspects, this study aimed to evaluate the adsorption capacity of a halloysite-magnetite-based composite in the removal of Congo red dye from aqueous solutions. The effects of stirring rate, pH, initial dye concentration and contact time were investigated. The results revealed that the adsorption kinetics followed the pseudo-second-order model, and equilibrium was well represented by the Brunauer-Emmett-Teller isotherm. The thermodynamic data showed that dye adsorption onto the composite was spontaneous and endothermic and occurred by physisorption. Finally, the composite could also be regenerated at least four times by calcination and was shown to be a promising adsorbent for the removal of this dye.

  1. Ammonia nitrogen removal from aqueous solution by local agricultural wastes

    Science.gov (United States)

    Azreen, I.; Lija, Y.; Zahrim, A. Y.

    2017-06-01

    Excess ammonia nitrogen in the waterways causes serious distortion to environment such as eutrophication and toxicity to aquatic organisms. Ammonia nitrogen removal from synthetic solution was investigated by using 40 local agricultural wastes as potential low cost adsorbent. Some of the adsorbent were able to remove ammonia nitrogen with adsorption capacity ranging from 0.58 mg/g to 3.58 mg/g. The highest adsorption capacity was recorded by Langsat peels with 3.58 mg/g followed by Jackfruit seeds and Moringa peels with 3.37 mg/g and 2.64 mg/g respectively. This experimental results show that the agricultural wastes can be utilized as biosorbent for ammonia nitrogen removal. The effect of initial ammonia nitrogen concentration, pH and stirring rate on the adsorption process were studied in batch experiment. The adsorption capacity reached maximum value at pH 7 with initial concentration of 500 mg/L and the removal rate decreased as stirring rate was applied.

  2. Removal of Metal Nanoparticles Colloidal Solutions by Water Plants

    Science.gov (United States)

    Olkhovych, Olga; Svietlova, Nataliia; Konotop, Yevheniia; Karaushu, Olena; Hrechishkina, Svitlana

    2016-11-01

    The ability of seven species of aquatic plants ( Elodea canadensis, Najas guadelupensis, Vallisneria spiralis L., Riccia fluitans L., Limnobium laevigatum, Pistia stratiotes L., and Salvinia natans L.) to absorb metal nanoparticles from colloidal solutions was studied. It was established that investigated aquatic plants have a high capacity for removal of metal nanoparticles from aqueous solution (30-100%) which indicates their high phytoremediation potential. Analysis of the water samples content for elements including the mixture of colloidal solutions of metal nanoparticles (Mn, Cu, Zn, Ag + Ag2O) before and after exposure to plants showed no significant differences when using submerged or free-floating hydrophytes so-called pleuston. However, it was found that the presence of submerged hydrophytes in aqueous medium ( E. canadensis, N. guadelupensis, V. spiralis L., and R. fluitans L.) and significant changes in the content of photosynthetic pigments, unlike free-floating hydrophytes ( L. laevigatum, P. stratiotes L., S. natans L.), had occur. Pleuston possesses higher potential for phytoremediation of contaminated water basins polluted by metal nanoparticles. In terms of removal of nanoparticles among studied free-floating hydrophytes, P. stratiotes L. and S. natans L. deserve on special attention.

  3. Removal of fluoride ions from aqueous solution by waste mud

    International Nuclear Information System (INIS)

    Kemer, Baris; Ozdes, Duygu; Gundogdu, Ali; Bulut, Volkan N.; Duran, Celal; Soylak, Mustafa

    2009-01-01

    The present study was carried out to assess the ability of original waste mud (o-WM) and different types of activated waste mud which are acid-activated (a-WM) and precipitated waste mud (p-WM), in order to remove excess of fluoride from aqueous solution by using batch technique. The p-WM exhibited greater performance than the others. Adsorption studies were conducted as a function of pH, contact time, initial fluoride concentration, adsorbent concentration, temperature, etc. Studies were also performed to understand the effect of some co-existing ions present in aqueous solutions. Adsorption process was found to be almost independent of pH for all types of waste mud. Among the kinetic models tested for p-WM, pseudo-second-order model fitted the kinetic data well with a perfect correlation coefficient value of 1.00. It was found that the adequate time for the adsorption equilibrium of fluoride was only 1 h. Thermodynamic parameters including the Gibbs free energy (ΔG o ), enthalpy (ΔH o ), and entropy (ΔS o ) revealed that adsorption of fluoride ions on the p-WM was feasible, spontaneous and endothermic in the temperature range of 0-40 deg. C. Experimental data showed a good fit with the Langmuir and Freundlich adsorption isotherm models. Results of this study demonstrated the effectiveness and feasibility of WM for removal of fluoride ions from aqueous solution.

  4. Removal of fluoride ions from aqueous solution by waste mud

    Energy Technology Data Exchange (ETDEWEB)

    Kemer, Baris; Ozdes, Duygu; Gundogdu, Ali; Bulut, Volkan N.; Duran, Celal [Karadeniz Technical University, Faculty of Arts and Sciences, Department of Chemistry, 61080 Trabzon (Turkey); Soylak, Mustafa, E-mail: soylak@erciyes.edu.tr [Erciyes University, Faculty of Arts and Sciences, Department of Chemistry, 38039 Kayseri (Turkey)

    2009-09-15

    The present study was carried out to assess the ability of original waste mud (o-WM) and different types of activated waste mud which are acid-activated (a-WM) and precipitated waste mud (p-WM), in order to remove excess of fluoride from aqueous solution by using batch technique. The p-WM exhibited greater performance than the others. Adsorption studies were conducted as a function of pH, contact time, initial fluoride concentration, adsorbent concentration, temperature, etc. Studies were also performed to understand the effect of some co-existing ions present in aqueous solutions. Adsorption process was found to be almost independent of pH for all types of waste mud. Among the kinetic models tested for p-WM, pseudo-second-order model fitted the kinetic data well with a perfect correlation coefficient value of 1.00. It was found that the adequate time for the adsorption equilibrium of fluoride was only 1 h. Thermodynamic parameters including the Gibbs free energy ({Delta}G{sup o}), enthalpy ({Delta}H{sup o}), and entropy ({Delta}S{sup o}) revealed that adsorption of fluoride ions on the p-WM was feasible, spontaneous and endothermic in the temperature range of 0-40 deg. C. Experimental data showed a good fit with the Langmuir and Freundlich adsorption isotherm models. Results of this study demonstrated the effectiveness and feasibility of WM for removal of fluoride ions from aqueous solution.

  5. Selective removal of mercury from aqueous solutions using thiolated cross-linked polyethylenimine

    Science.gov (United States)

    Saad, Dalia M.; Cukrowska, Ewa M.; Tutu, Hlanganani

    2013-06-01

    A successful approach to develop an insoluble form of polyethylenimine with a thiol-based functional group for selective removal of Hg(II) from aqueous solutions is reported. The selectivity of the modified polymer for Hg(II) as well as its ability to be regenerated for re-use has been studied. The synthesised polymer exhibited high selectivity for Hg(II) with high removal efficiency of up to 97 %, even in the presence of competing ions. The Freundlich isotherm was found to best fit and describe the experimental data. The pseudo-second-order equation explains the adsorption kinetics most effectively implying chemisorption. The thermodynamic study of the adsorption process revealed high activation energies >41 kJ mol-1, further confirming chemisorption as the mechanism of interaction between mercury ions and the polymer surface. The polymer exhibited good potential for re-use after many cycles of regeneration, giving good removal efficiency up to the fifth cycle.

  6. Evaluation of sorptive flotation technique for enhanced removal of radioactive Eu(III) from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Ezzat, Amir; Saad, Ebtissam A. [Ain Shams Univ., Cairo (Egypt). Chemistry Dept.; Mahmoud, Mamdoh R. [Atomic Energy Authority, Cairo (Egypt). Nuclear Chemistry Dept.; Soliman, Mohamed A. [Atomic Energy Authority, Cairo (Egypt). Egypt Second Research Reactor; Kandil, Abdelhakim [Helwan Univ., Cairo (Egypt). Chemistry Dept.

    2017-06-01

    The present study aims at the removal of Eu(III) from aqueous solutions by sorptive flotation process. This process involves adsorption of Eu(III) onto bentonite and kaolinite clays followed by floatation using sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB) collectors. The effect of adsorption parameters (pH, contact time, clay weight, Eu(III) concentration, ionic strength) as well as flotation parameters (collector and frother concentrations, bubbling time, concentrations of foreign cations and anions) on the removal efficiency of Eu(III) were studied. The obtained results show that Eu(III) ions are removed efficiently (R% ∝ 95%) at pH=4 after 1 h shaking with clay and 15 min floatation. The adsorption kinetics of Eu(III) onto the employed clays followed the pseudo-second-order model and the equilibrium data fitted well to the Freundlich isotherm model.

  7. Electrochemical removal of copper ions from dilute solutions using packed bed electrode. Part І

    Directory of Open Access Journals (Sweden)

    I.A. Khattab

    2013-06-01

    Full Text Available Removal of some hazardous waste like copper from effluent streams has an industrial importance. In this field, this paper is directed towards electrochemical removal of copper ions from sulfate solution using packed bed electrode. The cathode packing is in static mode, consisted of graphite particles, with mean particle size equal to 0.125 cm. The high surface area of this cell is expected to give high current efficiency and removal percent. The effect of current density and liquid flow rate were tested. Experimental results obtained indicate that the efficiencies are in direct proportional with current density while inversely proportional with liquid flow rate. It was observed that, using this cell was effective in reducing copper concentration to less than 4 mg/l with R.E of 96.2% during 30 min electrolysis time.

  8. Malachite green "a cationic dye" and its removal from aqueous solution by adsorption

    Science.gov (United States)

    Raval, Nirav P.; Shah, Prapti U.; Shah, Nisha K.

    2017-11-01

    Adsorption can be efficiently employed for the removal of various toxic dyes from water and wastewater. In this article, the authors reviewed variety of adsorbents used by various researchers for the removal of malachite green (MG) dye from an aqueous environment. The main motto of this review article was to assemble the scattered available information of adsorbents used for the removal of MG to enlighten their wide potential. In addition to this, various optimal experimental conditions (solution pH, equilibrium contact time, amount of adsorbent and temperature) as well as adsorption isotherms, kinetics and thermodynamics data of different adsorbents towards MG were also analyzed and tabulated. Finally, it was concluded that the agricultural solid wastes and biosorbents such as biopolymers and biomass adsorbents have demonstrated outstanding adsorption capabilities for removal of MG dye.

  9. Potential of Brass to Remove Inorganic Hg(II) from Aqueous Solution through Amalgamation.

    Science.gov (United States)

    Wenke, Axel; Bollen, Anne; Richard, Jan-Helge; Biester, Harald

    2016-06-01

    Brass shavings (CuZn45) were tested for their efficiency to remove Hg(II) from contaminated groundwater through amalgamation. The study was focused on long-term retention efficiency, the understanding of the amalgamation process and kinetics, and influences of filter surface alteration. Column tests were performed with brass filters (thickness 3 to 9 cm) flushed with 1000 μg/L Hg solution for 8 hours under different flow rates (300 to 600 mL/h). Brass filters consistently removed >98% of Hg from solution independent of filter thickness and flow rate. In a long-term experiment (filter thickness 2 cm), Hg retention decreased from 96 to 92% within 2000 hours. Batch and column experiments for studying kinetics of Hg removal indicate ~100% Hg removal from solution within only 2 hours. Solid-phase mercury thermo-desorption analysis revealed that Hg(0) diffusion into the brass surface controls kinetics of mercury retention. Brass surface alteration could be observed, but did not influence Hg retention.

  10. Application of Azolla for 2, 4, 6-Trichlorophenol (TCP Removal from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Zazouli

    2013-11-01

    Full Text Available Background & Aims of the Study: The 2, 4, 6-Trichlorophenol (TCP is a phenolic compound which it can produce adverse effects on human and environment. Therefore, the removal of these compounds is necessary. The aim of this study is the investigation of TCP removal by using Azolla filiculoides biomass. Materials & Methods: The Azolla biomass was dried in the sunlight, and then it was crushed and sieved to particle sizes in range of 1-2 mm. Next treated with 0.1M HCl for a period of 5h. The Azolla was washed with distilled water and it was used as adsorbent. The effect of operating parameters such as pH, contact time, TCP concentration and adsorbent dose on the TCP removal efficiency was investigated. The residues concentration of TCP was measured by spectrophotometer in λ max of 296 nm. Results: In optimum condition (pH 3, contact time 120 min , adsorbent dose 10 gr/l and TCP concentration 10 ppm, Azolla was able to remove 95% of TCP from aqueous solutions. The equilibrium data follows the Langmuir isotherm and the proper kinetic model is pseudo-second model. Conclusions: Adsorption process by Azolla filiculoides is an efficient method for removal of 2, 4, 6-Trichlorophenol from aqueous solutions.

  11. Removal of phenol from radioactive waste solutions using activated granular Carbon and activated vermiculite

    International Nuclear Information System (INIS)

    Ezz El-Din, M.R.; Atta, E.R.

    2006-01-01

    The efficiency of both activated granular carbon (AGC) and activated vermiculite (AV) in removal of phenol from aqueous waste solutions is of great interest. The aim of the present study is to compare the absorbance capacities of both AGC and AV for the removal of phenol from radioactive waste solutions and to identify the factors affecting the sorption process. The experimental results were in the form of batch sorption measurements for the removal of phenol at ambient temperature (29 ± 1 degree C) and for times up to 40 min and 180 min for AGC and AV, respectively. The results indicated that activated carbon has good efficiency to adsorb phenol. Freundlich equation has been fitted to both AGC and AV for the contaminant removal. The adsorption capacities of both AGC and AV to phenol were 17.4 mg g-1 and 4.5 mg g-1, respectively. The maximum desorption percent of phenol from both loaded AGC and loaded AV were 9 % and 0 %, respectively, and it attained within about 200 min. accordingly, it is recommended that activated carbon is preferred in the applied field for removing phenol from radioactive aqueous wastes

  12. Removal of radioactive materials from waste solutions via magnetic ferrites

    International Nuclear Information System (INIS)

    Boyd, T.E.; Kochen, R.L.; Price, M.Y.

    1982-01-01

    Ferrite waste treatment was found to be effective in removing actinides from simulated Rocky Flats process waste solutions. With a one-stage ferrite treatment, plutonium concentrations were consistently reduced from 10 -4 g/l to less than 10 -8 g/l, and americium concentrations were lowered from 10 -7 g/l to below 10 -10 g/l. In addition, siginficantly less solid was produced as compared with the flocculant precipitation technique now employed at Rocky Flats. Aging of ferrite solids and elevated beryllium and phosphate concentrations were identified as interferences in the ferrite treatment of process waste, but neither appeeared serious enough to prevent implementation in plant operations

  13. Morphology of modified biochar and its potential for phenol removal from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Kostas A. Komnitsas

    2016-04-01

    Full Text Available In the present study, the efficiency of phenol removal from synthetic aqueous solutions by chemically modified biochar with the use of 1M KOH or 1M FeCl3 was investigated. Initially, biochar was produced after slow pyrolysis of three different agricultural wastes, namely pistachio (Pistacia vera L. shells, pecan (Carya illinoinensis shells and wood sawdust. The quality of biochar was assessed by evaluating its main properties, such as pH, surface area, porosity and C content. X-ray diffraction (XRD, Scanning Electron Microscopy (SEM and Fourier Transform Infrared Spectroscopy (FTIR were used for the identification of biochar’s structure. The efficiency of phenol removal from synthetic solutions was assessed with the use of kinetic and equilibrium experiments. The experimental results show that the KOH-modified biochar exhibited the highest phenol removal efficiency. Hydrophobic sorption on its surface is the main phenol removal mechanism. The pseudo-second order model fits best the kinetic data, while the Freundlich model, as deduced from an equilibrium study describes very well sorption of phenols on all biochars examined.

  14. Arsenic Removal from Aqueous Solutions Using Modified and Unmodified Oak Sawdust

    Directory of Open Access Journals (Sweden)

    Ali Reza Rahmani

    2016-01-01

    Full Text Available In this research, oak sawdust, in both modified and unmodified forms, was used as an economical and low-cost material for the removal of arsenic from aqueous solutions. For this purpose, arsenic synthetic samples were prepared using NaAsO2 in distilled water and the effects of pH, adsorbent dosage, contact time, and initial As(V concentration were investigated on As(V adsorption using the adsorbents prepared. The results showed that modified sawdust achieved the highest efficiency (>91% over a contact time of 60 min and at pH 7 when the adsorbent dosage was 4gr/L and the initial As(V concentration was 150 µg/L. The data from both adsorbents fitted well to the Langmuir isotherm. Under optimum conditions (an initial As(V concentration of 150 µg/L and optimal absorption pH, contact time, and adsorbent dosage, maximum As(V removal efficiencies were 93.85% and 91.034% with the modified  and unmodified sawdust adsorbents, respectively. Given the availability and low cost of the adsorbent used and the high removal efficiency obtained at  lower adsorbent dosages and contact times, the modified oak sawdust may be recommended as an effective adsorbent for the removal of arsenic (v from aqueous solutions, especially since it requires no need for pH modification.

  15. Efficiency of Electrocoagulation for Removal of Reactive Yellow 14 from Aqueous Environments

    Directory of Open Access Journals (Sweden)

    Ahmad Reza Yaria

    2013-09-01

    Full Text Available Background & Aims of the Study: Discharge of textile industry colored wastewater without enough treatment into natural water resources cause serious pollution. Most of the conventional wastewater treatment methods are not effective enough to remove these dyes from wastewater. In this study, efficiency of electrocoagulation process with iron electrodes for treatment of Reactive Yellow 14 dye from synthetic solution has been studied and concluded. Materials & Methods: This experiment was conducted in a batch system with a volume of 2 L that had been equipped with 4 iron electrodes. The effect of operating parameters, such as voltage, time of reaction, initial dye concentration, and interelectrode distance on the dye removal efficiency was investigated. Results: In optimum condition (pH 2, voltage 40 V, electrolysis time 25 min, and interelectrode distance 1 cm, electrocoagulation method was able to remove 99.27% of Reactive Yellow 14 from synthetic solution. Conclusions: Electrocoagulation process by iron electrode is an efficient method for removal of reactive dyes from colored solution.

  16. Removal of fission products from waste solutions using 16 different soil samples

    International Nuclear Information System (INIS)

    Bangash, M.A.; Hanif, J.

    1997-01-01

    Most of the nuclear sites use pits in the surrounding soils for the storage/disposal of low active waste (LAW) solutions. The characteristics of the soil if not suitable for the fixation or adsorption of the radioactive nuclides, may cause migration of these nuclides to hydrosphere. The phenomenon has the risk of radio toxic pollution for the living bodies therefore minerals composing the soil and their adsorption properties need to be investigated. For this purpose 16 different soil samples were collected from all over Pakistan. Mineralogical composition of the soils was determined by X-ray diffraction analysis. It was found that most of the samples contained clay minerals, illite, kaolinite and montmorillonite. Studies for the removal of fission products like, /sup 137/Cs. /sup 60/Sr and activation product /sup 60/CO from solution were carried out on these samples. The sorption experiments were performed by batch technique using radioactive as tracers. Distribution co-efficient were determined by mixing he element solution at pH 3 with the soil at soil solution ratios of 1 to 20. It is revealed from the experimental data that efficient removal of fission products from solutions is achieved by soil samples containing clay mineral montmorillonite, followed by little and kaolinite. These soils thus can be effectively used for the disposal of low level radioactive waste solutions without causing any environmental hazard. (author)

  17. Novel geochemistry-inspired method for the deep removal of vanadium from molybdate solution

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jialiang [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing, 100083 (China); Beijing Key Laboratory of Green Recycling and Extraction of Metals, Beijing, 100083 (China); Deng, Yuping; Zhou, Qiuyue; Qin, Peixin; Liu, Yubo [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing, 100083 (China); Wang, Chengyan, E-mail: chywang@yeah.net [School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing, 100083 (China)

    2017-06-05

    Highlights: • A geochemistry-inspired method was developed for removal of V from molybdates. • Magnetic separation of the Fe{sub 3}O{sub 4} adsorbent took 10 s. • Vanadium can be deeply removed in 5 min at pH of 7.0–11.0. • Fe{sub 3}O{sub 4} adsorbent has excellent V selectivity and reusability. • A flowchart is presented for Mo/V separation in the leachate of spent HDS catalyst. - Abstract: Separation of vanadium from molybdates is an essential task for processing the leaching solution of hazardous spent hydrodesulphurization (HDS) catalyst. In this study, the difference in the main naturally occurring mineral forms of Mo and V inspired us to develop a method for the deep removal of V from molybdate solution using Fe{sub 3}O{sub 4} as an adsorbent. First, the adsorbent was synthesized with coprecipitation method, and then it was characterized by XRD, TEM, and VSM. The synthesized material consisted of pure Fe{sub 3}O{sub 4} nanoparticles that exhibited paramagnetic property, with a saturated magnetization of 68.6 emu g{sup −1}. The V removal efficiency was investigated using batch adsorption experiments in varying conditions. Results indicated that V could be deeply removed from various concentrations of molybdate solution at pH of 7.0–11.0 within 5 min. A slight decrease was found in the adsorption ratio after the adsorbent had been reused for 4 cycles. The resulting molybdate solution contained less than 0.02 g L{sup −1} of V, which satisfies the requirement for preparing high-quality products. Finally, a process flowchart is presented for the separation of Mo and V from the leaching solution of spent HDS catalyst, based on the excellent V removal performance and rapid separation rate of the Fe{sub 3}O{sub 4} adsorbent.

  18. Process for the removal of radium from acidic solutions containing same

    International Nuclear Information System (INIS)

    Scheitlin, F.M.

    1984-01-01

    Radium is removed from an inorganic-acid solution contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities. The invention is applicable, for example, to the recovery of 226 Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings, and thus contain thorium and uranium. The contaminated fly ash may be incorporated in a suitable matrix and stored, and the residual solutions processed to separate uranium and thorium. (author)

  19. Optimization of uranyl ions removal from aqueous solution by natural and modified kaolinites

    Energy Technology Data Exchange (ETDEWEB)

    Elhefnawy, O.A.; Elabd, A.A. [Nuclear and Radiological Regulatory Authority (NRRA), Cairo (Egypt). Nuclear Safeguards and Physical Protection Dept.

    2017-10-01

    The paper addresses the modifications of the most common mineral clay ''kaolinite'' for U(VI) removal from aqueous solutions. A new modified Egyptian natural kaolinite (Ca-MK) was prepared by coating kaolinite with calcium oxide. Another modification process was utilized by calcination and acid activation of kaolinite (E-MK). The Egyptian natural kaolinite (E-NK) and the two modified kaolinites were characterized by different techniques SEM, EDX, XRD, and FTIR. The removal process were investigated in batch experiments as a function of pH, contact time, initial U(VI) concentration, effect of temperature, and recovery of U(VI) were studied. The equilibrium stage was achieved after 60 min and the kinetic data was described well by pseudo-second order model. Isothermal data was better described by the Langmuir isotherm model, indicating the homogeneous removal process. Also the removal process was studied on different temperature 293, 313, and 323 K. The thermodynamic parameters ΔH , ΔS , and ΔG were calculated. The thermodynamic results pointed to the endothermic and favorable nature of the U(VI) removal process in the three kaolinite adsorbents. This study indicated that (Ca-MK) has higher CEC and can be used as a new adsorbent for highly efficient removal of U(VI) from aqueous solutions.

  20. IODINE REMOVAL EFFICIENCY IN NON-SUBMERGED AND SUBMERGED SELF-PRIMING VENTURI SCRUBBER

    Directory of Open Access Journals (Sweden)

    MAJID ALI

    2013-04-01

    Full Text Available The objective of this conducted research is to study the iodine removal efficiency in a self-priming venturi scrubber for submerged and non-submerged operating conditions experimentally and theoretically. The alkaline solution is used as an absorbent, which is prepared by dissolving sodium hydroxide (NaOH and sodium thiosulphate (Na2S2O3 in water to remove the gaseous iodine (I2 from the gas. Iodine removal efficiency is examined at various gas flow rates and inlet concentrations of iodine for submerged and non-submerged operating conditions. In the non-submerged venturi scrubber, only the droplets take part in iodine removal efficiency. However, in a submerged venturi scrubber condition, the iodine gas is absorbed from gas to droplets inside the venturi scrubber and from bubbles to surrounding liquid at the outlet of a venturi scrubber. Experimentally, it is observed that the iodine removal efficiency is greater in the submerged venturi scrubber as compare to a non-submerged venturi scrubber condition. The highest iodine removal efficiency of 0.99±0.001 has been achieved in a submerged self-priming venturi scrubber condition. A mathematical correlation is used to predict the theoretical iodine removal efficiency in submerged and non-submerged conditions, and it is compared against the experimental results. The Wilkinson et al. correlation is used to predict the bubble diameter theoretically whereas the Nukiyama and Tanasawa correlation is used for droplet diameter. The mass transfer coefficient for the gas phase is calculated from the Steinberger and Treybal correlation. The calculated results for a submerged venturi scrubber agree well with experimental results but underpredicts in the case of the non-submerged venturi scrubber.

  1. Iodine Removal Efficiency in Non-Submerged and Submerged Self-Priming Venturi Scrubber

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Majid; Yan, Changqi; Sun, Zhongning; Gu, Haifeng; Wang, Junlong; Mehboob; Khurram [Harbin Engineering Univ., Harbin (China)

    2013-04-15

    The objective of this conducted research is to study the iodine removal efficiency in a self-priming venturi scrubber for submerged and non-submerged operating conditions experimentally and theoretically. The alkaline solution is used as an absorbent, which is prepared by dissolving sodium hydroxide (NaOH) and sodium thiosulphate (Na{sub 2}S{sub 2}O{sub 3}) in water to remove the gaseous iodine (I{sub 2}) from the gas. Iodine removal efficiency is examined at various gas flow rates and inlet concentrations of iodine for submerged and non-submerged operating conditions. In the non-submerged venturi scrubber, only the droplets take part in iodine removal efficiency. However, in a submerged venturi scrubber condition, the iodine gas is absorbed from gas to droplets inside the venturi scrubber and from bubbles to surrounding liquid at the outlet of a venturi scrubber. Experimentally, it is observed that the iodine removal efficiency is greater in the submerged venturi scrubber as compare to a non-submerged venturi scrubber condition. The highest iodine removal efficiency of 0.99±0.001 has been achieved in a submerged self-priming venturi scrubber condition. A mathematical correlation is used to predict the theoretical iodine removal efficiency in submerged and non-submerged conditions, and it is compared against the experimental results. The Wilkinson et al. correlation is used to predict the bubble diameter theoretically whereas the Nukiyama and Tanasawa correlation is used for droplet diameter. The mass transfer coefficient for the gas phase is calculated from the Steinberger and Treybal correlation. The calculated results for a submerged venturi scrubber agree well with experimental results but underpredicts in the case of the non-submerged venturi scrubber.

  2. Iodine Removal Efficiency in Non-Submerged and Submerged Self-Priming Venturi Scrubber

    International Nuclear Information System (INIS)

    Ali, Majid; Yan, Changqi; Sun, Zhongning; Gu, Haifeng; Wang, Junlong; Mehboob; Khurram

    2013-01-01

    The objective of this conducted research is to study the iodine removal efficiency in a self-priming venturi scrubber for submerged and non-submerged operating conditions experimentally and theoretically. The alkaline solution is used as an absorbent, which is prepared by dissolving sodium hydroxide (NaOH) and sodium thiosulphate (Na 2 S 2 O 3 ) in water to remove the gaseous iodine (I 2 ) from the gas. Iodine removal efficiency is examined at various gas flow rates and inlet concentrations of iodine for submerged and non-submerged operating conditions. In the non-submerged venturi scrubber, only the droplets take part in iodine removal efficiency. However, in a submerged venturi scrubber condition, the iodine gas is absorbed from gas to droplets inside the venturi scrubber and from bubbles to surrounding liquid at the outlet of a venturi scrubber. Experimentally, it is observed that the iodine removal efficiency is greater in the submerged venturi scrubber as compare to a non-submerged venturi scrubber condition. The highest iodine removal efficiency of 0.99±0.001 has been achieved in a submerged self-priming venturi scrubber condition. A mathematical correlation is used to predict the theoretical iodine removal efficiency in submerged and non-submerged conditions, and it is compared against the experimental results. The Wilkinson et al. correlation is used to predict the bubble diameter theoretically whereas the Nukiyama and Tanasawa correlation is used for droplet diameter. The mass transfer coefficient for the gas phase is calculated from the Steinberger and Treybal correlation. The calculated results for a submerged venturi scrubber agree well with experimental results but underpredicts in the case of the non-submerged venturi scrubber

  3. Hydraulic washing removal efficiencies of Orimulsion from rock surfaces

    International Nuclear Information System (INIS)

    Harper, J.R.; Ward, S.; Sergy, G.

    2002-01-01

    Orimulsion is a fuel alternative composed of 70 per cent bitumen in 30 per cent water. It is shipped from Venezuela to New Brunswick where it is used as fuel oil for power plants. While there have not been any major spills of Orimulsion, it is recognized that very little is known regarding the dispersal and weathering processes of Orimulsion, or the behaviour and cleanup of the product on both rocky and course sediment shorelines. For that reason, this study was conducted to determine the efficiency of hydraulic washing under different water temperatures and pressures to remove bitumen from rocky shorelines. The results of the study make it possible to assess the physical effectiveness of the method and to determine the range of effective operational parameters. The coating protocol was refined to create uniform coating of both dispersed and coalesced bitumen of rock surfaces. The use of a chemical agent for enhancing removal efficiency was also assessed. Orimulsion could reach shorelines as low concentration dispersions of bitumen particles suspended in a water column, or as a high concentration mixture of bitumen, water and air. Granite tiles were coated with uniform coatings of both dispersed and coalesced bitumen. They were then washed under different pressures, temperatures and other treatments. Temperatures of more than 40 degrees C and pressures of more than 76 kPa were needed to effectively remove the bitumen coatings. Weathering significantly increased coating tenacity for dispersed coatings, but did not affect coalesced coating tenacity. Immediate washing was found to be very effective for removing dispersed coating, but not for coalesced coating. Coating tenacity was also affected by submergence times. Pre-treatment of the coating with a dispersion called Corexit significantly improved the removal efficiencies of dispersed coatings, but not coalesced coatings. 6 refs., 10 tabs., 5 figs

  4. Improving energy efficiency in industrial solutions - Walk the talk

    Energy Technology Data Exchange (ETDEWEB)

    Wegener, D. (Siemens AG. Industry Solutions Div., Erlangen (Germany)); Finkbeiner, M. (Technische Univ. Berlin (TUB). Sustainable Engineering, Berlin (Germany)); Holst, J.-C.; Walachowicz, F. (Siemens AG. Corporate Technology, Berlin (Germany)); Irving Olsen, S. (Technical Univ. of Denmark (DTU). Management Engineering, Kgs. Lyngby (Denmark))

    2011-05-15

    This paper describes the outline of the energy efficiency and environmental care policy and management at Siemens Industry Solutions Division. This environmental policy coherently embraces strategic planning, eco-design of energy-efficient industrial processes and solutions, design evaluation and finally communication of both environmental and economic performance of solutions to customers. One of the main tools supporting eco-design and evaluation and controlling of derived design solutions is the so called 'Eco-Care-Matrix' (ECM). The ECM simply visualizes the eco-efficiency of solutions compared to a given baseline. In order to prevent from 'green washing' criticism and to ensure 'walk the talk' attitude the ECM should be scientifically well-founded using appropriate and consistent methodology. The vertical axis of an ECM illustrates the environmental performance and the horizontal axis describes the economical customer benefit of one or more green solutions compared to a defined reference solution. Different scientific approaches for quantifying the environmental performance based on life cycle assessment methodology are discussed especially considering the ISO standards 14040/14044:2006. Appropriate ECM application is illustrated using the example of the Siemens MEROS technology (Maximized Emission Reduction of Sintering) for the steel industry. MEROS is currently the most modern and powerful system for cleaning off-gas in sinter plants. As an environmental technology MEROS is binding and removing sulfur dioxide and other acidic gas components present in the off-gas stream by using dry absorbents and additional electrical power. Advantage in the impact category of acidification potential (by desulfurization) is a trade-off to disadvantages in global warming and resource depletion potential caused by use of electricity. Representing different impacts, indicator results for impact categories with different tendencies have to be

  5. Hydrocolloid-Stabilized Magnetite for Efficient Removal of Radioactive Phosphates

    Directory of Open Access Journals (Sweden)

    Vinod Vellora Thekkae Padil

    2014-01-01

    Full Text Available Liquid radioactive waste is a common by-product when using radioactive isotopes in research and medicine. Efficient remediation of such liquid waste is crucial for increasing safety during the necessary storage of the material. Herein, we present a novel Gum Karaya stabilized magnetite for the efficient removal of radioactive phosphorus 32P from liquid radioactive waste. This environmentally friendly material is well suited to be used as a nanohydrogel for the removal of liquid waste, which can then be stored in a smaller space and without the risk of the spills inherent to the initial liquid material. The maximum adsorption capacity of the GK/M in this study was found to be 15.68 GBq/g. We present a thorough morphological characterization of the synthesised GK/M, as well as a discussion of the possible phosphorus adsorption mechanisms.

  6. Electrochemical removal of indium ions from aqueous solution using iron electrodes

    International Nuclear Information System (INIS)

    Chou, Wei-Lung; Huang, Yen-Hsiang

    2009-01-01

    The removal of indium ions from aqueous solution was carried out by electrocoagulation in batch mode using an iron electrode. Various operating parameters that could potentially affect the removal efficiency were investigated, including the current density, pH variation, supporting electrolyte, initial concentration, and temperature. The optimum current density, supporting electrolyte concentration, and temperature were found to be 6.4 mA/cm 2 , 0.003N NaCl, and 298 K, respectively. When the pH values lower than 6.1, the removal efficiencies of indium ions via electrocoagulation were up to 5 times greater than those by adding sodium hydroxide. The indium ion removal efficiency decreased with an increase in the initial concentration. Results for the indium ion removal kinetics at various current densities show that the kinetic rates conformed to the pseudo-second-order kinetic model with good correlation. The experimental data were also tested against different adsorption isotherm models for describing the electrocoagulation process. The adsorption of indium ions preferably fitting the Langmuir adsorption isotherm suggests monolayer coverage of adsorbed molecules.

  7. Electrochemical removal of indium ions from aqueous solution using iron electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Chou, Wei-Lung, E-mail: wlchou@sunrise.hk.edu.tw [Department of Safety, Health and Environmental Engineering, Hungkuang University, No. 34 Chung-Chie Road, Sha-Lu, Taichung 433, Taiwan (China); Huang, Yen-Hsiang [Department of Safety, Health and Environmental Engineering, Hungkuang University, No. 34 Chung-Chie Road, Sha-Lu, Taichung 433, Taiwan (China)

    2009-12-15

    The removal of indium ions from aqueous solution was carried out by electrocoagulation in batch mode using an iron electrode. Various operating parameters that could potentially affect the removal efficiency were investigated, including the current density, pH variation, supporting electrolyte, initial concentration, and temperature. The optimum current density, supporting electrolyte concentration, and temperature were found to be 6.4 mA/cm{sup 2}, 0.003N NaCl, and 298 K, respectively. When the pH values lower than 6.1, the removal efficiencies of indium ions via electrocoagulation were up to 5 times greater than those by adding sodium hydroxide. The indium ion removal efficiency decreased with an increase in the initial concentration. Results for the indium ion removal kinetics at various current densities show that the kinetic rates conformed to the pseudo-second-order kinetic model with good correlation. The experimental data were also tested against different adsorption isotherm models for describing the electrocoagulation process. The adsorption of indium ions preferably fitting the Langmuir adsorption isotherm suggests monolayer coverage of adsorbed molecules.

  8. Investigation of Phenol Removal from Aqueous Solutions by Electrofenton and Electropersulfate Processes

    Directory of Open Access Journals (Sweden)

    Alireza Rahmani

    2016-11-01

    Full Text Available Phenol, or benzene hydroxyl is a toxic aromatic hydrocarbon discharged into the environment through certian industrial effluents which, thereby, pollute water resources. This study examines phenol removal from aqueous solutions through electro-Fenton and electro/persulfate processes using iron electrodes. For this purpose, a laboratory-scale electrochemical batch reactor was used that was equipped with four electrodes and a direct DC power supply. In the tests carried out, the effects of operational parameters such as initial pH; current density; and initial concentrations of phenol, hydrogen peroxide, and persulfate on the removal of phenol were investigated. The results showed that EPS and EF processes achieved phenol removal efficiencies of 95.18% and 93.99%, respectively, at operating conditions of pH = 3, initial phenol concentration of 100 mg/l, hydrogen peroxide and persulfate concentration of 0. 4 mM, and a current density 0.07A/dm2 over 45 min. Increasing persulfate and hydrogen peroxide concentration from 0.4 to 0.8 mM reduced phenol removal efficiencies from 95.18% and 93.99% to 43% and 85%, respectively. Generally speaking, EPS and EF processes exhibited almost identical phenol removal efficiencies. Finally, the integrated electrochemical and persulphate process was found to be more productive in producing electrical iron and persulphate activation than using each single process in isolation.

  9. Highly efficient removal of pathogenic bacteria with magnetic graphene composite.

    Science.gov (United States)

    Zhan, Sihui; Zhu, Dandan; Ma, Shuanglong; Yu, Wenchao; Jia, Yanan; Li, Yi; Yu, Hongbing; Shen, Zhiqiang

    2015-02-25

    Magnetic Fe3O4/graphene composite (abbreviated as G-Fe3O4) was synthesized successfully by solvothermal method to effectively remove both bacteriophage and bacteria in water, which was tested by HRTEM, XRD, BET, XPS, FTIR, CV, magnetic property and zeta-potential measurements. Based on the result of HRTEM, the single-sheet structure of graphene oxide and the monodisperse Fe3O4 nanoparticles on the surface of graphene can be observed obviously. The G-Fe3O4 composite were attractive for removing a wide range of pathogens including not only bacteriophage ms2, but also various bacteria such as S. aureus, E. coli, Salmonella, E. Faecium, E. faecalis, and Shigella. The removal efficiency of E. coli for G-Fe3O4 composite can achieve 93.09%, whereas it is only 54.97% with pure Fe3O4 nanoparticles. Moreover, a detailed verification test of real water samples was conducted and the removal efficiency of bacteria in real water samples with G-Fe3O4 composite can also reach 94.8%.

  10. Study of iodine removal efficiency in self-priming venturi scrubber

    International Nuclear Information System (INIS)

    Ali, Majid; Yan, Changqi; Sun, Zhongning; Gu, Haifeng; Wang, Junlong

    2013-01-01

    Highlights: ► Study of iodine removal efficiency in a self-priming venturi scrubber. ► Investigation of iodine removal efficiency at different gas and liquid flow rates. ► Investigation of different inlet concentrations of iodine. ► Mathematical model based on mass transfer. - Abstract: Venturi scrubber is used in filtered vented containment system of nuclear power plants to remove the gaseous pollutants from contaminated gas during severe accidents. In this research, an experimental and theoretical investigation has been carried out to study the iodine removal efficiency in a self-priming venturi scrubber. The aqueous solution is prepared by adding weight percentage of sodium hydroxide 0.5% and sodium thiosulphate 0.2% in scrubbing water to increase the absorbance of inorganic iodine (I 2 ) from the contaminated gas during emission. The iodine removal efficiency is investigated at various gas and liquid flow rates, and iodine inlet concentrations. The iodine removal efficiency is measured experimentally by measuring the inlet and outlet concentration of iodine at sampling ports. The petite droplets are formed in a venturi scrubber to absorb the iodine through the mass transfer phenomenon. A mathematical model for mass transfer based on a gas liquid interface is employed for the verification of experimental results. The contact time between iodine and scrubbing solution depends on the total volumetric flow of gas and liquid, and volume of throat and diffuser of the venturi scrubber. Sauter mean diameter is calculated from the Nukiyama and Tanasawa correlation. Steinberger and Treybal’s correlation is used to measure the mass transfer coefficient for the gas phase. The results calculated from the model under predict the experimental data

  11. Removing efficiency of radon from water by different methods

    International Nuclear Information System (INIS)

    Muellerova, M.; Holy, K.; Gulasova, Z.; Polaskova, A.

    2008-01-01

    In this contribution problem of radon removing from water samples by different methods was tested. Lowest efficiency of deemanation was achieved at tossing of water from one vessel into the other. For increasing of efficiency deemanation of radon use of needle-bath principle was also used. Low efficiency deemanation was found at trapping of radon from sample of water by toluene (83 ± 5) %, too. Reversal highest efficiency deemanation of radon from water was reached at aerating by argon (95 ± 6)%. It is shown, that reduction of volume activity of radon in water under 0.1 Bq/dm l - 3 is big problem. Suppression of this limit will claim use of more completion and sophistic approaches. (author)

  12. EVALUATION OF SOLVENTS EFFICIENCY IN CONDENSATE BANKING REMOVAL

    OpenAIRE

    CORREA, TOMAS; TIAB, DJEBBAR; RESTREPO, DORA PATRICIA

    2009-01-01

    This work describes experimental design and tests performed to simulate gas condensate reservoir conditions below dew point in the laboratory using three different compositions of synthetic gas condensate. Methanol, propanol and methylene chloride are the solvents used to remove the condensate banking and improve the gas effective permeability near to the wellbore. Solvents are injected in Berea sandstone rock with similar petrophysical properties in order to compare the efficiency at removin...

  13. Efficient Removal of Arsenic Using Magnetic Multi-Granule Nanoclusters

    International Nuclear Information System (INIS)

    Lee, Seungho; Cha, Jinmyung; Sim, Kyunjong; Lee, Jinkyu

    2014-01-01

    Magnetic multi-granule nanoclusters (MGNCs) were investigated as an inexpensive means to effectively remove arsenic from aqueous environment, particularly groundwater sources consumed by humans. Various size MGNCs were examined to determine both their capacity and efficiency for arsenic adsorption for different initial arsenic concentrations. The MGNCs showed highly efficient arsenic adsorption characteristics, thereby meeting the allowable safety limit of 10 μg/L (ppb), prescribed by the World Health Organization (WHO), and confirming that 0.4 g and 0.6 g of MGNCs were sufficient to remove 0.5 mg/L and 1.0 mg/L of arsenate (AsO 4 3- ) from water, respectively. Adsorption isotherm models for the MGNCs were used to estimate the adsorption parameters. They showed similar parameters for both the Langmuir and Sips models, confirming that the adsorption process in this work was active at a region of low arsenic concentration. The actual efficiency of arsenate removal was then tested against 1 L of artificial arsenic-contaminated groundwater with an arsenic concentration of 0.6 mg/L in the presence of competing ions. In this case, only 1.0 g of 100 nm MGNCs was sufficient to reduce the arsenic concentrations to below the WHO permissible safety limit for drinking water, without adjusting the pH or temperature, which is highly advantageous for practical field applications

  14. Efficient Removal of Arsenic Using Magnetic Multi-Granule Nanoclusters

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Seungho; Cha, Jinmyung; Sim, Kyunjong; Lee, Jinkyu [Seoul National Univ., Seoul (Korea, Republic of)

    2014-02-15

    Magnetic multi-granule nanoclusters (MGNCs) were investigated as an inexpensive means to effectively remove arsenic from aqueous environment, particularly groundwater sources consumed by humans. Various size MGNCs were examined to determine both their capacity and efficiency for arsenic adsorption for different initial arsenic concentrations. The MGNCs showed highly efficient arsenic adsorption characteristics, thereby meeting the allowable safety limit of 10 μg/L (ppb), prescribed by the World Health Organization (WHO), and confirming that 0.4 g and 0.6 g of MGNCs were sufficient to remove 0.5 mg/L and 1.0 mg/L of arsenate (AsO{sub 4}{sup 3-}) from water, respectively. Adsorption isotherm models for the MGNCs were used to estimate the adsorption parameters. They showed similar parameters for both the Langmuir and Sips models, confirming that the adsorption process in this work was active at a region of low arsenic concentration. The actual efficiency of arsenate removal was then tested against 1 L of artificial arsenic-contaminated groundwater with an arsenic concentration of 0.6 mg/L in the presence of competing ions. In this case, only 1.0 g of 100 nm MGNCs was sufficient to reduce the arsenic concentrations to below the WHO permissible safety limit for drinking water, without adjusting the pH or temperature, which is highly advantageous for practical field applications.

  15. REMOVAL OF TRICHLOROACETIC ACID FROM THE AQUEOUS SOLUTIONS USING NATURAL AND ACTIVATED LIGNITE COALS

    Directory of Open Access Journals (Sweden)

    Hüseyin GÜLENSOY

    1998-02-01

    Full Text Available In these studies, a typical lignite coal found near Istanbul (Yeniköy and its activated products were used to adsorb TCA from aqueous solutions. Particle sizes of coal samples and the concentrations of TCA solutions were chosen as parameters against the fixed amount of adsorbent. The maximum efficiency has been obtained for the coal having (-120 + 150 mesh size fraction activated by heating. As a result, it was shown that these kinds of lignite coals could be used as a good adsorbent. In addition, it was also proved that both the removal and recovery of TCA from some waste waters would easily be possible.

  16. Removal of Cd 2+ ion from diluted aqueous solutions by electrodeposition on reticulated vitreous carbon electrodes

    Directory of Open Access Journals (Sweden)

    Tramontina Jucelânia

    2002-01-01

    Full Text Available The electrodeposition of Cd2+ ion was investigated in pH 4.8 sulfuric-sulfate solutions in the presence of dissolved O2. In potentiostatic conditions, using reticulated vitreous carbon (RVC electrodes of 30, 60 and 100 pores per inch (ppi, high removal efficiency values were achieved in the potential range from --0.90 to --1.10 V for solutions containing 5 and 10 mg L-1 of Cd2+ ion. In this potential range, Cd electrodeposition is a mass transport controlled reaction and the concentration of the metallic ion decays exponentially with time following a pseudo-first order kinetics. For the 30 ppi RVC, the current efficiency and removal efficiency values found were, respectively, 45 % and 96 % for a solution containing 10 mg L-1 of Cd2+ ion after 30 minutes electrolysis at --0.90 V while 33 % and 99% were found for the 60 ppi RVC. The concentration decay of Cd2+ ion in the solution was monitored after each experiment by anodic stripping voltammetry at a hanging mercury drop electrode.

  17. Selective Removal of Uranium from the Washing Solution of Uranium-Contaminated Soil

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seung Soo; Han, G. S.; Kim, G. N.; Koo, D. S.; Jeong, J. W.; Choi, J. W. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    This study examined selective removal methods of uranium from the waste solution by ion exchange resins or solvent extraction methods to reduce amount of the 2{sup nd} waste. Alamine-336, known as an excellent extraction reagent of uranium from the leaching solution of uranium ore, did not remove uranium from the acidic washing solution of soil. Uranyl ions in the acidic waste solution were sorbed on ampholyte resin with a high sorption efficiency, and desorbed from the resin by a washing with 0.5 M Na{sub 2}CO{sub 3} solution at 60 .deg. C. However, the uranium dissolved in the sulfuric acid solution was not sorbed onto the strong anion exchanger resins. A great amount of uranium-contaminated (U-contaminated) soil had been generated from the decommissioning of a uranium conversion plant. Our group has developed a decontamination process with washing and electrokinetic methods to decrease the amount of waste to be disposed of. However, this process generates a large amount of waste solution containing various metal ions.

  18. Inorganic sorbents for radiostrontium removal from waste solutions: selectivity and role of calixarenes

    International Nuclear Information System (INIS)

    Vijayan, S.; Belikov, K.; Drapailo, A.

    2011-01-01

    The challenge in the remediation of 90 Sr-contaminated waters arises from the need to achieve very high removal efficiencies to meet discharge targets from waste effluents containing relatively high concentrations of non-radioactive cations. Low-cost natural zeolites are not selective for strontium over other divalent cations, notably such ions as calcium; and produce low 90 Sr removal performance, and large volumes of spent sorbent waste. The synthesis and use of selective, synthetic inorganic sorbents could prove to be a feasible approach for high 90 Sr removal efficiencies, and much smaller volumes of secondary solid waste generation. The essential advantages of inorganic sorbents include their stability and resistance to radiation, and the potential for producing stable waste forms such as vitrified glass or ceramics for disposal. However, the cost of strontium-specific sorbents is prohibitive for large-scale applications at present. This paper is a review of the reported information on removal mechanisms and performance of Sr-specific inorganic sorbents. The analysis has revealed promising performance, efficiency and selectivity for strontium removal from solutions containing low and high concentrations of salts. The leading sorbents are crystalline silicotitanate and oxides of metals such as titanium. An initial assessment has also been made of the performance of calixarene-based macrocyclic compounds. These are known for their selectivity for strontium in solvent extraction processes. From the initial strontium removal results in bench-scale tests using different solid substrates, impregnated with calixarene derivatives, only sodium-mordenite impregnated with calyx[8]arene octamide gave an overall strontium removal efficiency in the range of 90 to 95% in the presence of 3.5 ppm calcium. There was no improvement observed for strontium-removal efficiency or selectivity over calcium in the calixarene-impregnated inorganic sorbent matrix. In several tests, the

  19. Nitrate Removal from Aqueous Solutions Using Almond Charcoal Activated with Zinc Chloride

    Directory of Open Access Journals (Sweden)

    Mohsen Arbabi

    2017-10-01

    Full Text Available Background & Aims of the Study: Nitrate is one of the most important contaminants in aquatic environments that can leached to water resources from various sources such as sewage, fertilizers and decomposition of organic waste. Reduction of nitrate to nitrite in infant’s blood stream can cause “blue baby” disease in infants. The aim of this study was to evaluate the nitrate removal from aqueous solutions using modified almond charcoal with zinc chloride. Materials &Methods: This study is an experimental survey. At the first charcoal almond skins were prepared in 5500C and then modified with ZnCl2. Morphologies and characterization of almond shell charcoal were evaluated by using FTIR, EDX, BET and FESEM. Adsorption experiments were conducted with 500 ml sample in Becker. The nitrate concentration removal, contact time, pH and charcoal dosage were investigated. The central composite design method was used to optimizing the nitrate removal process. The results analyzed with ANOVA test. Results: The best condition founded in 48 min, 1250 ppm, 125 mg/l and 3 for retention time, primary nitrate concentration, charcoal dosage and pH respectively. The results showed that the nitrate removal decreases with increasing pH. Modification of skin charcoal is show increasing of nitrate removal from aquatic solution. Conclusion: In this study, the maximum nitrate removal efficiency for raw charcoal and modified charcoal was determined 15.47% and 62.78%, respectively. The results showed that this method can be used as an effective method for removing nitrate from aqueous solutions.

  20. Comparative efficiency of final endodontic cleansing procedures in removing a radioactive albumin from root canal systems

    International Nuclear Information System (INIS)

    Cecic, P.A.; Peters, D.D.; Grower, M.F.

    1984-01-01

    Fifty-six teeth were initially instrumented, with the use of seven irrigants or irrigant combinations, and filled with radioactive albumin. The study then showed the relative ability of three final endodontic procedures (copious reirrigation with saline solution, drying with paper points, and reassuring patency of the canal with the final instrument) to remove the albumin. Even after copious irrigation, each additional procedure removed statistically significant amounts of albumin. Alternating an organic solvent and an inorganic solvent did appear to leave the canal system in the optimal condition for final cleansing procedures. The study then correlated the relative efficiency of irrigation alone versus instrumentation plus irrigation in removing the remaining albumin from the canal systems. Reinstrumentation plus copious irrigation removed significantly more albumin than copious irrigation alone

  1. Electrocoagulation-Adsorption to Remove Anionic and Cationic Dyes from Aqueous Solution by PV-Energy

    Directory of Open Access Journals (Sweden)

    J. Castañeda-Díaz

    2017-01-01

    Full Text Available The cationic dye malachite green (MG and the anionic dye Remazol yellow (RY were removed from aqueous solutions using electrocoagulation-adsorption processes. Batch and continuous electrocoagulation procedures were performed and compared. Carbonaceous materials obtained from industrial sewage sludge and commercial activated carbons were used to adsorb dyes from aqueous solutions in column systems with a 96–98% removal efficiency. The continuous electrocoagulation-adsorption system was more efficient for removing dyes than electrocoagulation alone. The thermodynamic parameters suggested the feasibility of the process and indicated that the adsorption was spontaneous and endothermic (ΔS=0.037 and −0.009 for MG and RY, resp.. The ΔG value further indicated that the adsorption process was spontaneous (−6.31 and −10.48; T=303 K. The kinetic electrocoagulation results and fixed-bed adsorption results were adequately described using a first-order model and a Bohart-Adams model, respectively. The adsorption capacities of the batch and column studies differed for each dye, and both adsorbent materials showed a high affinity for the cationic dye. Thus, the results presented in this work indicate that a continuous electrocoagulation-adsorption system can effectively remove this type of pollutant from water. The morphology and elements present in the sludge and adsorbents before and after dye adsorption were characterized using SEM-EDS and FT-IR.

  2. Efficiency of Electrocoagulation for Removal of Reactive Yellow 14 from Aqueous Environments

    OpenAIRE

    Ahmad Reza Yaria; Mostafa Alizadeh; Sara Hashemi; Hamed Biglari

    2013-01-01

    Background & Aims of the Study: Discharge of textile industry colored wastewater without enough treatment into natural water resources cause serious pollution. Most of the conventional wastewater treatment methods are not effective enough to remove these dyes from wastewater. In this study, efficiency of electrocoagulation process with iron electrodes for treatment of Reactive Yellow 14 dye from synthetic solution has been studied and concluded. Materials & Methods: This exper...

  3. High efficiency particulate removal with sintered metal filters

    International Nuclear Information System (INIS)

    Kirstein, B.E.; Paplawsky, W.J.; Pence, D.T.; Hedahl, T.G.

    1981-01-01

    Because of their particle removal efficiencies and durability, sintered metal filters have been chosen for high efficiency particulate air (HEPA) filter protection in the off-gas treatment system for the proposed Idaho National Engineering Laboratory Transuranic Waste Treatment Facility. Process evaluation of sintered metal filters indicated a lack of sufficient process design data to ensure trouble-free operation. Subsequence pilot scale testing was performed with flyash as the test particulate. The test results showed that the sintered metal filters can have an efficiency greater than 0.9999999 for the specific test conditions used. Stable pressure drop characteristics were observed in pulsed and reversed flow blowback modes of operation. Over 4900 hours of operation were obtained with operating conditions ranging up to approximately 90 0 C and 24 vol % water vapor in the gas stream

  4. Feasibility of Cr (VI Removal from Aqueous Solution Using Electrochemical Bipolar Aluminum Electrodes

    Directory of Open Access Journals (Sweden)

    Abbas Rezaei

    2013-08-01

    Full Text Available Electrocoagulation is one of the technologies which have been considered by many researchers in recent years. This process has many advantages including high efficiency, no need to chemical addition, low sludge production, capability of process control, easy to operation and maintenance. Bipolar electrodes system is one of the electrocoagulation techniques which can be used for increasing the process efficiency and better distribution of the electric current. The aim of this study was to remove hexavalent chromium from aqueous solution by electrocoagulation technique. Response surface methodology (RSM was used to optimize the parameters involving in the process, and the effect of current density, initial chromium concentration and pH on the process were investigated. At optimal conditions, for the highest chromium removal (>90%, the optimum initial chromium, reaction time, current density and pH were found to be 117 mg/L, 50 min, 11.75 mA cm-2 and 4.5, respectively. It can be stated that electrocoagulation is an efficient technique for separation and removing high chromium concentration from aqueous solutions.

  5. Actinide removal from aqueous solution with activated magnetite

    International Nuclear Information System (INIS)

    Kochen, R.L.; Thomas, R.L.

    1987-01-01

    An actinide aqueous waste treatment process using activated magnetite has been developed at Rocky Flats. The use and effectiveness of various magnetites in lowering actinide concentrations in aqueous solution are described. Experiments indicate that magnetite particle size and pretreatment (activation of the magnetite surface with hydroxyl ions greatly influence the effective use of magnetite as an actinide adsorbent. With respect to actinide removal, Ba(OH) 2 -activated magnetite was more effective over a broader pH range than was NaOH-activated magnetite. About 50% less Ba(OH) 2 -activated magnetite was required to lower plutonium concentration from 10 -4 to 10 -8 g/l. 7 refs., 8 tabs

  6. MODELING AN ION EXCHANGE PROCESS FOR CESIUM REMOVAL FROM ALKALINE RADIOACTIVE WASTE SOLUTIONS

    International Nuclear Information System (INIS)

    Smith, F.; Hamm, Luther; Aleman, Sebastian; Michael, Johnston

    2008-01-01

    The performance of spherical Resorcinol-Formaldehyde ion-exchange resin for the removal of cesium from alkaline radioactive waste solutions has been investigated through computer modeling. Cesium adsorption isotherms were obtained by fitting experimental data using a thermodynamic framework. Results show that ion-exchange is an efficient method for cesium removal from highly alkaline radioactive waste solutions. On average, two 1300 liter columns operating in series are able to treat 690,000 liters of waste with an initial cesium concentration of 0.09 mM in 11 days achieving a decontamination factor of over 50,000. The study also tested the sensitivity of ion-exchange column performance to variations in flow rate, temperature and column dimensions. Modeling results can be used to optimize design of the ion exchange system

  7. Enveloped virus flocculation and removal in osmolyte solutions.

    Science.gov (United States)

    Gencoglu, Maria F; Heldt, Caryn L

    2015-07-20

    Our ability to reduce infectious disease burden throughout the world has been greatly improved by the creation of vaccines. However, worldwide immunization rates are low. The two most likely reasons are the lack of sufficient distribution in underdeveloped countries and the high cost of vaccine products. The high costs are due to the difficulties of manufacturing individual vaccine products with specialized purification trains. In this study, we propose to use virus flocculation in osmolytes, followed by microfiltration, as an alternative vaccine purification operation. In our previous work, we demonstrated that osmolytes preferentially flocculate a non-enveloped virus, porcine parvovirus (PPV). In this work we show that osmolytes flocculate the enveloped virus, Sindbis virus heat resistant strain (SVHR), and demonstrate a >80% removal with a 0.2 μm microfilter membrane while leaving proteins in solution. The best osmolytes were tested for their ability to flocculate SVHR at different concentrations, pH and ionic strengths. Our best removal was 98% of SVHR in 0.3M mannitol at a pH of 5. We propose that osmolytes are able to flocculate hydrophobic non-enveloped and enveloped virus particles by the reduction of the hydration layer around the particles, which stimulates virus aggregation. Now that we have demonstrated that protecting osmolytes flocculate viruses, this method has the potential to be a future platform purification process for vaccines. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Fluoride removal from diluted solutions by Donnan dialysis using full factorial design

    Energy Technology Data Exchange (ETDEWEB)

    Boubakri, Ali; Helali, Nawel; Tlili, Mohamed; Amor, Mohamed Ben [Center of Researches and Water Technologies, Soliman (Turkey)

    2014-03-15

    Excessive fluoride concentration in potable water can lead to fluorosis of teeth and bones. In the present study, Donnan dialysis (DD) is applied for the removal of fluoride ions from diluted sodium fluoride solutions. A four factor two level (2{sup 4}) full factorial design was used to investigate the influence of different physico-chemical parameters on fluoride removal efficiency (Y{sub F}) and fluoride flux (J{sub F}) through anion exchange membrane. The statistical design determines factors which have the important effects on Donnan dialysis performance and studies all interactions among the considered parameters. The four significant factors were initial fluoride concentration, feed flow rate, temperature and agitation speed. The experimental results and statistical analysis show that the temperature and agitation speed have positive effects on fluoride removal efficiency and the initial fluoride concentration has a negative effect. In the case of fluoride flux, feed flow rate and initial concentration are the main effect and all factors have a positive effect. The interaction between studied parameters was not negligible on two responses. A maximum fluoride removal of 75.52% was obtained under optimum conditions and the highest value of fluoride flux obtained was 2.4 mg/cm{sup 2}·h. Empirical regression models were also obtained and used to predict the flux and the fluoride removal profiles with satisfactory results.

  9. Application of Electrocoagulation Process for Reactive Red 198 Dye Removal from the Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Mansooreh Dehghani

    2014-04-01

    Full Text Available Abstract Background and purpose:The main objectives of this research were to evaluating the application of electrocoagulation process for 198 dye from the aqueous phase and determining the optimum operating conditions to the dye removal using aluminum and iron electrodes. Materials and Methods:The present study was conducted in bench-scale. The spectrophotometer DR 5000 was used to determine the dye concentration. The effects of pH, retention time, voltage, dye concentration on the efficiency of electrocoagulation process were investigated. Data were analyzed in SPSS for Windows 16.0 using Pearson’scorrelation coefficient to analyze the relationship between these parameters. Results:The results showed that the optimal conditions for reactive red 198 (RR-198 dye removal from the aqueous solution are pH of 11, the voltage of 32 V, the initial dye concentration of 10 ppm, and the reaction time of 40 min. Pearson correlation analysis showed that there is a significant relationship between voltage and the reaction time with the removal efficiencies (P< 0.01. Conclusion:It was revealed that the removal efficiency of dye was directly proportional to the voltage and reaction time, but inversely proportional to the initial dye concentration. In conclusion, electrocoagulation process using two-fold iron and aluminum electrodes is an appropriate method for reducing the RR-198 dye in the aqueous phase.

  10. Removal of Nickel from Aqueous Solution by Hard-Shell Pistachios

    Directory of Open Access Journals (Sweden)

    Shayan Shamohammadi

    2013-08-01

    Full Text Available Nickel is one of the heavy metals which commonly can be found in industrial wastewater. Many studies have been done on agricultural waste for the removal of nickel from aqueous solutions. The purpose of this study is to identify hard-shell pistachios as a local attraction for removal of nickel from aqueous solution. Nickel adsorption isotherm models are studied using shell pistachios. Pistachio shell was chosen which its particle size is between 800-600 microns. The stock solution of nickel ions was prepared mixing nickel nitrate with distilled water. The results showed that the maximum absorption efficiency occurs (73.3% at pH=8. Also, it was shown that with increasing adsorbent dose, equilibrium time decreased within constant concentration. Examination of uptake isotherm models showed that models of Freundlich, BET, Radke-Praunitz, Redlich-Peterson and Sips describe data in 97% level of confidence well,  however Freundlich and Sips isotherm models has the lowest error factor 0.10597 and 0/10598 respectively and the highest correlation coefficient (0.9785. Comparison of adsorbent capacity within removal of nickel from aqueous solution shows that Pistachio shell with special absorbent surface of 1.7 m2/g and uptake capacity of 0.3984 mg/g is proper than adsorbents of Kaolinite, Bagasse, sludge-ash.

  11. Efficient removal of UDMH from dilute nitride MOCVD exhaust streams

    Science.gov (United States)

    Pahle, Jörg; Czerniak, Mike; Seeley, Andy; Baker, Derek

    2004-12-01

    Unsymmetrical dimethyl hydrazine (UDMH) (CH 3) 2N 2H 2 is often used in the deposition of dilute nitride semiconductors because it provides a source of nitrogen with a low thermal decomposition temperature (Temperature-dependent carrier lifetime in GaNAs using resonant-coupled photoconductive decay, NCPV Program Review Meeting, Lakewood, Colorado, 14-17 October, 2001). The problems with using this material, however, are its significant toxicity (0.01 ppm compared to ammonia's 25 ppm) and also the fact that it blocks the action of conventional dosed wet scrubbers sometimes used on nitride applications, resulting in diminished efficiency in removing arsine (the source of arsenic), and arsine being similarly toxic (TLV of 0.05 ppm). Efficient removal of UDMH, AsH 3 and hydrogen (which, though not toxic poses a potential safety hazard) by means of a combined thermal oxidation reaction and wet scrubber in series is described at input gas flow rates exceeding those typically encountered in practice. The detection technique employed was Fourier transform infra red spectroscopy (FTIR), and the calibration and resolution techniques will be described. For input UDMH flows of up to 445 sccm (i.e. 1.85×10 -2 mol/min), destructive reaction efficiencies (DREs) of >99.9% were demonstrated, corresponding to the background detection resolution of 0.4 ppm.

  12. Metal ion removal from aqueous solution using physic seed hull.

    Science.gov (United States)

    Mohammad, Masita; Maitra, Saikat; Ahmad, Naveed; Bustam, Azmi; Sen, T K; Dutta, Binay K

    2010-07-15

    The potential of physic seed hull (PSH), Jantropha curcas L. as an adsorbent for the removal of Cd(2+) and Zn(2+) metal ions from aqueous solution has been investigated. It has been found that the amount of adsorption for both Cd(2+) and Zn(2+) increased with the increase in initial metal ions concentration, contact time, temperature, adsorbent dosage and the solution pH (in acidic range), but decreased with the increase in the particle size of the adsorbent. The adsorption process for both metal ions on PSH consists of three stages-a rapid initial adsorption followed by a period of slower uptake of metal ions and virtually no uptake at the final stage. The kinetics of metal ions adsorption on PSH followed a pseudo-second-order model. The adsorption equilibrium data were fitted in the three adsorption isotherms-Freundlich, Langmuir and Dubinin-Radushkevich isotherms. The data best fit in the Langmuir isotherm indication monolayer chemisorption of the metal ions. The adsorption capacity of PSH for both Zn(2+) and Cd(2+) was found to be comparable with other available adsorbents. About 36-47% of the adsorbed metal could be leached out of the loaded PSH using 0.1M HCl as the eluting medium. 2010 Elsevier B.V. All rights reserved.

  13. A Mechatronic Solution for Efficiency Optimisation

    DEFF Research Database (Denmark)

    Conrad, Finn; Hansen, M.R.; Andersen, T.O.

    2004-01-01

    This paper presents and discusses concepts concerning regeneration of potential energy in hydraulic forklift trucks. A conventional forklift system has been investigated for energy efficiency and compared to an investigated for energy efficiency and compared to an investigated for energy efficien...

  14. Fabrication of nano Delafossite LiCo{sub 0.5}Fe{sub 0.5}O{sub 2} as the new adsorbent in efficient removal of reactive blue 5 from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Khosravi, Iman, E-mail: khosraviiman@yahoo.com [Department of Chemistry, Qeshm Branch, Islamic Azad University, Qeshm (Iran, Islamic Republic of); Yazdanbakhsh, Mohammad [Department of Chemistry, Faculty of Sciences, Ferdowsi University of Mashhad, Mashhad 917791436 (Iran, Islamic Republic of); Eftekhar, Melika [Department of Chemistry, Qeshm Branch, Islamic Azad University, Qeshm (Iran, Islamic Republic of); Haddadi, Zohreh [Department of Chemistry, Faculty of Sciences, Ferdowsi University of Mashhad, Mashhad 917791436 (Iran, Islamic Republic of)

    2013-06-01

    Highlights: ► Fabrication of nano Delafossite LiCo{sub 0.5}Fe{sub 0.5}O{sub 2} by sol–gel method. ► Kinetic study of the adsorption properties. ► Removal of reactive blue 5 (RB5) as a reactive dye by the prepared new nanocatalyst. - Abstract: In this paper, nanoparticles of delafossite-type LiCo{sub 0.5}Fe{sub 0.5}O{sub 2} were prepared by sol–gel method in the presence of maleic acid as a chelating agent. The nanoparticles were characterized using differential thermal analysis, X-ray powder diffraction, Fourier infrared spectroscopy, transmission electron microscope, scanning electron microscopy and scanning tunneling microscopy. The nanoparticles showed the excellent adsorption properties towards reactive dye, reactive blue 5 (RB5). The adsorption studies were carried out at different pH values, various adsorbent dosages and contact time in a batch experiments. The kinetic studies indicate that the removal process obeys the second-order kinetic equation. Also, the isotherm evaluations reveal that the adsorption of RB5 by the nanoparticles follows the Freundlich model.

  15. Efficiency of WWTP to remove emerging pollutants in wastewater

    Science.gov (United States)

    Carmona, Eric; Llopis, Agustín; Andreu, Vicente; Picó, Yolanda

    2016-04-01

    Recently some compounds that are extensively used are considered emerging pollutants since are at low concentrations and have been little studied. Pharmaceuticals and personal care products are classified as this kind of pollutants and most of these are excreted through urine or feces and come to end up to treatment plants. Recent studies indicates that pharmaceuticals, personal care products or illicit drugs from Waste Water Treatment Plants (WWTP) are a considerable chemical pollution in surface [1, 2]. The purpose of this study is to determine the removal efficiency for two WWT of Pinedo I and II, Valencia (Spain). After obtaining the results of analysis by an Agilent 1260 HPLC in tandem with a 6410 MS/MS triple quad, a simple mathematical operation with the influents and effluents is performed. This operation consists in subtracted from the influent, the effluent, divided by the result of the influent and this multiply by 100. Results are expressed as a percentage with its 95 % confidence interval (CI). The influent and effluent of the samples were filtered with a 0.50 μm glass fiber filter of 90 mm by Advantec (Minato-ku, Tokyo, Japan). After filtration, 250ml of this water is extracted through a SPE. SPE was performed with Strata-X 33U Polymeric Reversed Phase (200 mg/6 mL) from Phenomenex. These cartridges were conditioned with 6 mL of methanol and 6 mL of distilled water. Extracts were eluted with 6mL of Methanol and evaporated with compressed air. The residue was reconstituted with 1 mL of methanol-water (30:70, v/v). The removal efficiencies depend on the type of the compound, these rates remain between 23% and 100%. In some cases, removal efficiency is negative since some compounds are accumulated in the sludge and these have more concentration. Tertiary treatment including UV disinfection could efficiently reduce most of the residual pharmaceuticals below their quantification limits. Acknowledgments This work has been supported by the Spanish Ministry

  16. Efficient TEA CO2 laser based coating removal system

    CSIR Research Space (South Africa)

    Prinsloo, FJ

    2007-04-01

    Full Text Available stream_source_info Prinsloo_2007.pdf.txt stream_content_type text/plain stream_size 11617 Content-Encoding UTF-8 stream_name Prinsloo_2007.pdf.txt Content-Type text/plain; charset=UTF-8 Efficient TEA CO2 laser based... by keeping energy density below the damage threshold. The advantage of a pulsed TEA CO2 laser system is that a laser frequency and temporal profile can be chosen to maximize paint removal and concurrently minimize substrate damage. To achieve...

  17. Products of radiation removal of lead from aqueous solutions

    International Nuclear Information System (INIS)

    Drtinova, Barbora; Pospisil, Milan

    2008-01-01

    Full text: Some metal ions, including Pb 2+ can be gradually reduced by primary reducing products of water radiolysis (solvated electrons e aq - and H radicals) to insoluble, easily separable metals. Conditions of water remediation using irradiation with accelerated electrons were studied. The solutions with initial concentration 100 mg/L of Pb(II) (originally nitrate) containing OH radical scavengers were irradiated under intensive agitation in sealed thin-glass ampoules by accelerated electrons (4.5 MeV) from a linear accelerator. Doses ranging from 0.5 to 60 kGy (dose rate of 0.5 kGy/s) determined by an alanine dosimeter were applied. Subsequent process of centrifugation (5000 revs per minute) was used for the separation of product- finely dispersed particles. The changes in metal concentration were determined with error ± 3% by means of atomic absorption spectroscopy with flame atomization. The solid products formed after the irradiation were analyzed by both thermogravimetry and differential thermal analysis. For the pre-irradiated systems were carried out calculations by using PHREEQC in order to determinate the speciation. Without addition of an OH radical scavenger the radiation-induced removal of lead did not occur. The influence of potassium formate HCOOK (1x10 -3 - 4x10 -2 mol/L) and 10% isopropanol as typical OH radical scavengers was individually studied. The lead can be completely removed from aqueous solutions (pH about 5-6) containing 1x10 - :2 mol/L of HCOOK already at the dose of 2.5 kGy. With increasing concentration of HCOOK (1x10 -3 - 4x10 -2 mol/L) increases the amount of Pb(HCOO) + form in the solution before irradiation. The radiation product is metallic lead at low concentration of HCOOK to PbCO 3 at higher concentration of the OH radical scavenger. In the system with isopropanol dominates the form Pb 2+ and the product of radiation reduction is then metallic lead

  18. Arsenic removal in solution using non living bio masses of aquatic weed

    International Nuclear Information System (INIS)

    Marin A, M. J.

    2010-01-01

    Arsenic is a metalloid considered among the most dangerous to health. The As maximum level allowed of drinkable water is 0.01 mg/L established by the Who. Several techniques have been proposed to remove arsenic from water, among which are the sorption processes in economic biological materials, which has advantages for its high efficiency in dilute toxic removing from contaminated water, for these reason it is necessary to study new bio sorbents materials which are economic, simple and easy to apply in the treatment of contaminated areas. The aim of this project was evaluate the removal of As (V) in solution using two non living aquatic plants: water hyacinth (Eichhornia crassipes) and lesser duckweed (Lemna minor), characterize these materials and compare the efficiency between both; the parameters evaluated were the As (V) initial concentration in solution, contact time, ph value and the amount of biomass in contact with them. It describes the method to prepare the non living plants. The physicochemical characterization by scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric analysis was made. The results shown that cellulose is the main component confirmed by the techniques above mentioned. Surface characterization of Eichhornia crassipes and Lemna minor by specific surface area, shown 1.3521 m 2 /g and 0.6395 m 2 /g respectively, the hydration kinetic indicates that 24 h was the maximum hydration time for both plants; the point of zero charge determination by mass titration gives a ph=6.1 for the first plant and ph=7.1 for the second plant, finally the active site density obtained for the plants were of 8.57 sites/nm 2 and 12.47 sites/nm 2 . The point of zero charge was analyzed for know the ph from which the As (V) species are removal preferably. Tested contact processes between bio sorbent-As (V) were performed to assess the ability of bio masses to removal As (V) from aqueous solutions, investigated

  19. High efficiency particulate removal with sintered metal filters

    International Nuclear Information System (INIS)

    Kirstein, B.E.; Paplawsky, W.J.; Pence, D.T.; Hedahl, T.G.

    1981-01-01

    Because of their particle removal efficiencies and durability, sintered metal filters have been chosen for HEPA filter protection in the off-gas treatment system for the proposed Idaho National Engineering Laboratory Transuranic Waste Treatment Facility. Process evaluation of sintered metal filters indicated a lack of sufficient process design data to assume trouble-free operation. Subsequent pilot-scale testing was performed with fly ash as the test particulate. The test results showed that the sintered metal filters can have an efficiency greater than 0.9999999 for the specific test conditions used. Stable pressure drop characteristics were observed in pulsed and reversed flow blowback modes of operation. Over 4900 hours of operation were obtained with operating conditions ranging up to approximately 90 0 C and 24 volume percent water vapor in the gas stream

  20. Removal of insecticide carbofuran from aqueous solutions by banana stalks activated carbon

    International Nuclear Information System (INIS)

    Salman, J.M.; Hameed, B.H.

    2010-01-01

    In this work, activated carbon was prepared from banana stalks (BSAC) waste to remove the insecticide carbofuran from aqueous solutions. The effects of contact time, initial carbofuran concentration, solution pH and temperature (30, 40 and 50 deg. C) were investigated. Adsorption isotherm, kinetics and thermodynamics of carbofuran on BSAC were studied. Equilibrium data were fitted to the Langmuir, Freundlich and Temkin isotherm models and the data best represented by the Langmuir isotherm. Thermodynamic parameters such as standard enthalpy (ΔH o ), standard entropy (ΔS o ) and standard free energy (ΔG o ) were evaluated. Regeneration efficiency of spent BSAC was studied using ethanol as a solvent. The efficiency was found to be in the range of 96.97-97.35%. The results indicated that the BSAC has good regeneration and reusability characteristics and can be used as alternative to present commercial activated carbon.

  1. Removal of phosphorus from aqueous solution by Posidonia oceanica fibers using continuous stirring tank reactor

    Energy Technology Data Exchange (ETDEWEB)

    Wahab, Mohamed Ali, E-mail: waheb_med@yahoo.fr [University of Carthage, Water Research and Technologies Centre (CERTE), Wastewater Treatment and Recycling Laboratory, B.P. 273, 8020 Soliman (Tunisia); Hassine, Rafik Ben [International Environmental Green Technology (IGET) (Tunisia); Jellali, Salah, E-mail: salah.jallali@certe.rnrt.tn [University of Carthage, Water Research and Technologies Centre (CERTE), Wastewater Treatment and Recycling Laboratory, B.P. 273, 8020 Soliman (Tunisia)

    2011-05-15

    The present study aims to develop a new potentially low-cost, sustainable treatment approach to soluble inorganic phosphorus removal from synthetic solutions and secondary wastewater effluents in which a plant waste (Posidonia oceanica fiber: POF) is used for further agronomic benefit. Dynamic flow tests using a continuous stirred tank reactor (CSTR) were carried out to study the effect of initial concentration of phosphorus, amount of adsorbent, feeding flow rate and anions competition. The experimental results showed that the removal efficiency of phosphorus from synthetic solutions is about 80% for 10 g L{sup -1} of POF. In addition, the variation of the initial concentration of phosphorus from 8 to 50 mg L{sup -1} increased the adsorption capacity from 0.99 to 3.03 mg g{sup -1}. The use of secondary treated wastewater showed the presence of competition phenomenon between phosphorus and sulphate which could be overcoming with increasing the sorptive surface area and providing more adsorption sites when increasing the adsorbent dosage of POF. Compared with columns studies, this novel CSTR system showed more advantages for the removal of soluble phosphorus as a tertiary treatment of urban secondary effluents with more adsorption efficiency and capacity, in addition to the prospect use of saturated POF with nutriment as fertilizer and compost.

  2. Removal of phosphorus from aqueous solution by Posidonia oceanica fibers using continuous stirring tank reactor

    International Nuclear Information System (INIS)

    Wahab, Mohamed Ali; Hassine, Rafik Ben; Jellali, Salah

    2011-01-01

    The present study aims to develop a new potentially low-cost, sustainable treatment approach to soluble inorganic phosphorus removal from synthetic solutions and secondary wastewater effluents in which a plant waste (Posidonia oceanica fiber: POF) is used for further agronomic benefit. Dynamic flow tests using a continuous stirred tank reactor (CSTR) were carried out to study the effect of initial concentration of phosphorus, amount of adsorbent, feeding flow rate and anions competition. The experimental results showed that the removal efficiency of phosphorus from synthetic solutions is about 80% for 10 g L -1 of POF. In addition, the variation of the initial concentration of phosphorus from 8 to 50 mg L -1 increased the adsorption capacity from 0.99 to 3.03 mg g -1 . The use of secondary treated wastewater showed the presence of competition phenomenon between phosphorus and sulphate which could be overcoming with increasing the sorptive surface area and providing more adsorption sites when increasing the adsorbent dosage of POF. Compared with columns studies, this novel CSTR system showed more advantages for the removal of soluble phosphorus as a tertiary treatment of urban secondary effluents with more adsorption efficiency and capacity, in addition to the prospect use of saturated POF with nutriment as fertilizer and compost.

  3. Magnetic biochar combining adsorption and separation recycle for removal of chromium in aqueous solution.

    Science.gov (United States)

    Xin, Ouyang; Yitong, Han; Xi, Cao; Jiawei, Chen

    2017-03-01

    Biochar has been developed in recent years for the removal of contaminants such as Cr (VI) in water. The enhancement of the adsorption capacity of biochar and its recyclable use are still challenges. In this study, magnetic biochar derived from corncobs and peanut hulls was synthesized under different pyrolysis temperatures after pretreating the biomass with a low concentration of 0.5 M FeCl 3 solution. The morphology, specific surface area, saturation magnetization and Fourier transform infrared spectroscopy (FT-IR) spectra were characterized for biochar. The magnetic biochar performed well in combining adsorption and separation recycle for the removal of Cr (VI) in water. The Cr (VI) adsorbance of the biochar was increased with the increase in pyrolysis temperature, and the magnetic biochar derived from corncobs showed better performance for both magnetization and removal of Cr (VI) than that from peanut hulls. The Langmuir model was used for the isothermal adsorption and the maximum Cr (VI) adsorption capacity of corncob magnetic biochar pyrolyzed at 650 °C reached 61.97 mg/g. An alkaline solution (0.1 M NaOH) favored the desorption of Cr (VI) from the magnetic biochar, and the removal of Cr (VI) still remained around 77.6% after four cycles of adsorption-desorption. The results showed that corncob derived magnetic biochar is a potentially efficient and recoverable adsorbent for remediation of heavy metals in water.

  4. A new alternative adsorbent for the removal of cationic dyes from aqueous solution

    Directory of Open Access Journals (Sweden)

    T. Santhi

    2016-09-01

    Full Text Available Adsorption of Malachite green (MG and Methylene blue (MB from aqueous solutions on low cost adsorbent prepared from Annona squmosa seed (CAS is studied experimentally. Results obtained indicate that the removal efficiency of Malachite green and Methylene blue at 27 ± 2 °C exceeds 75.66% and 24.33% respectively, and that the adsorption process is highly pH-dependent. Results showed that the optimum pH for dye removal is 6.0. The amount of dye adsorbed from aqueous solution increases with the increase of the initial dye concentration. Smaller adsorbent particle adds to increase the percentage removal of Malachite green and Methylene blue. The equilibrium data fitted well to the Langmuir model (R2 > 0.97 and the adsorption kinetic followed the pseudo-second-order equation (R2 > 0.99. The maximum adsorption capacities of MG, MB on CAS are 25.91 mg g−1 and 08.52 mg g−1 respectively. These results suggest that A. squmosa seed is a potential low-cost adsorbent for the dye removal from industrial wastewater. The adsorption capacity of CAS on MG is greater than MB.

  5. Storage Duration and Temperature Effects of Strychnos potatorum Stock Solutions on its Coagulation Efficiency

    Directory of Open Access Journals (Sweden)

    Rekha R Warrier

    2014-12-01

    Full Text Available This study presents the effects of storage duration and temperature of Strychnos potatorum stock solution on its coagulation efficiency. Coagulation efficiency of the seed extracts on water samples depended on the initial turbidity of the water sample. The stock solutions could clarify only highly turbid solutions. The optimum dosage of the stock solutions was 5% and optimal time required was 50 minutes. S. potatorum stock solutions, which were kept at room temperature (28 °C, had a shelf life of only five days and were able to remove turbidity from high and low turbidity water samples and no coagulation activity was observed for medium turbidity. The highest turbidity removals were observed for stock solutions, which were kept for three days. For stock solutions which were stored in refrigerator, shelf life was extended upto seven days, and the turbidity removal efficiencies improved from 45.9 to 63.8 for low and 43.7 to 64.9 % for high turbidity water samples, respectively.

  6. Removal of copper ions from aqueous solutions by means of micellar-enhanced ultrafiltration

    Directory of Open Access Journals (Sweden)

    Kowalska Izabela

    2017-01-01

    Full Text Available The aim of the study was to assess the usefulness of micellar–enhanced ultrafiltration (MEUF for removal of copper ions from water solutions in comparison with classic ultrafiltration process. The tests were conducted in a semi–pilot membrane installation with the use of ultrafiltration module KOCH/ROMICON® at a transmembrane pressure of 0.05 MPa. The effect of concentration of copper ions on ultrafiltration process efficiency was investigated. The second part of the tests concerned the removal of copper ions by MEUF under wide range of anionic surfactant concentration (0.25, 1, and 5 CMC (critical micelle concentration. Concentration of copper ions in model solutions was equal to 5, 20, and 50 mg Cu/L. Furthermore, the effect of surfactant leakage to the permeate side during filtration was evaluated. Conducted experiments confirmed effectiveness of MEUF in copper ions removal. For the highest copper concentration in the feed (i.e. 50 mg/L, the average concentration of copper ions in the permeate ranged from 1.2–4.7 mg Cu/L depending on surfactant concentration. During filtration experiments, UF module exhibited stable transport properties for model solutions containing copper. For the highest concentration of metal, the decrease of permeate flux did not exceed 11% after 60 minutes of filtration. In the presence of the surfactant, a slight deterioration of transport properties was observed.

  7. Removal of Cr(VI from Aqueous Solutions Using mino-fuctionalized Nanoporous MCM-41

    Directory of Open Access Journals (Sweden)

    Farshid Ghorbani

    2016-09-01

    Full Text Available An amino-functionalized nanoporous material was prepared by grafting 3-aminopropyl trimethoxysilane (APTMS group onto MCM-41. The as-synthesized material was characterized by X-ray diffraction (XRD analysis, nitrogen adsorption-desorption measurements (BET, thermogravimetric analysis (TGA, and Fourier transform infrared spectrometry (FTIR to confirm the ordered mesoporous structure and the functionalization of the amino group. The NH2-MCM-41 thus obtained was employed as the sorbent to remove Cr(VI ions from aqueous solutions. The batch adsorption process was carried out to evaluate the effects of solution pH, adsorbent dosage, metal ion concentration, and temperature. Results revealed that removal efficiency increased to a maximum of 124 mg.g‒1 and metal uptake decreased (0.1 g.l‒1 with increasing sorbent dosage from 0.1 to 3.5 g.l‒1. A reverse trend was, however, observed with increasing Cr(VI concentration. It was also found that a pH equal to 3 was the optimum level for the removal of Cr(VI ions from aqueous solutions. Thermodynamic examinations revealed the strong dependence of the adsorption process on temperature such that adsorption capacity increased with increasing temperature, indicating the endothermic and spontaneous nature of the adsorption process.

  8. Removal of cadmium from aqueous solution using marine green algae, Ulva lactuca

    Directory of Open Access Journals (Sweden)

    Mohamed M. Ghoneim

    2014-01-01

    Full Text Available The present study aimed to evaluate the efficiency of marine algae for removal of metals from the aqueous solution. The green alga, Ulva lactuca, collected from the intertidal zone of the Suez Bay, northern part of the Red Sea was used to reduce cadmium levels from the aqueous solutions. The biosorption mechanisms of Cd2+ ions onto the algal tissues were examined using various analytical techniques: Fourier-transform infrared spectroscopy (FT-IR and Scanning electron microscopy (SEM. Results indicated that at the optimum pH value of 5.5; about 0.1 g of U. lactuca was enough to remove 99.2% of 10 mg L−1 Cd2+ at 30 °C in the aqueous solutions. The equilibrium data were well fitted with the Langmuir and Freundlich isotherms. The monolayer adsorption capacity was 29.1 mg g−1. The calculated RL and ‘n’ values have proved the favorability of cadmium adsorption onto U. lactuca. The desorption test revealed that HCl was the best for the elution of metals from the tested alga. In conclusion, the seaweed U. lactuca was the favorable alternative of cadmium removal from water.

  9. Modeling of Malachite Green Removal from Aqueous Solutions by Nanoscale Zerovalent Zinc Using Artificial Neural Network

    Directory of Open Access Journals (Sweden)

    Wenqian Ruan

    2017-12-01

    Full Text Available The commercially available nanoscale zerovalent zinc (nZVZ was used as an adsorbent for the removal of malachite green (MG from aqueous solutions. This material was characterized by X-ray diffraction and X-ray photoelectron spectroscopy. The advanced experimental design tools were adopted to study the effect of process parameters (viz. initial pH, temperature, contact time and initial concentration and to reduce number of trials and cost. Response surface methodology and rapidly developing artificial intelligence technologies, i.e., artificial neural network coupled with particle swarm optimization (ANN-PSO and artificial neural network coupled with genetic algorithm (ANN-GA were employed for predicting the optimum process variables and obtaining the maximum removal efficiency of MG. The results showed that the removal efficiency predicted by ANN-GA (94.12% was compatible with the experimental value (90.72%. Furthermore, the Langmuir isotherm was found to be the best model to describe the adsorption of MG onto nZVZ, while the maximum adsorption capacity was calculated to be 1000.00 mg/g. The kinetics for adsorption of MG onto nZVZ was found to follow the pseudo-second-order kinetic model. Thermodynamic parameters (ΔG0, ΔH0 and ΔS0 were calculated from the Van’t Hoff plot of lnKc vs. 1/T in order to discuss the removal mechanism of MG.

  10. Performance Evaluation of Ozonation Combined with Persulfate Application for Removal of Furfural from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Alireza Rahmani

    2017-03-01

    Full Text Available Background: Furfural is an organic compound which derived from a variety industrial, including petrochemicals, pulping, pharmaceutical, food. Also is a main agent in many industries and aromatic organic compounds entrance in the environment. There are several methods of treating including physical, chemical, biological and physicochemical for remove this matter. Among advanced oxidation methods can be combined ozonation process with persulfate catalytic are noted. The purpose of this study was to evaluate the efficiency of ozonation process with the use of persulfate in removal furfural from aqueous solution. Materials and Methods: In this study, the efficiency of the process with a concentration furfural 5 to 30 mg/L, concentration persulfate 4 to 15 mM, pH = 3-11 and reaction time of 35 minutes in the semi-continuous reactor with a capacity of one liter was obtained. Results: The results of this study have been shown in  conditions of operation optimal , pH =,3 persulfate dosage 12 mM, ozone dosage of 1 g/min and the initial concentration of furfural  5 mg/L, this process is capable  remove of %93/34 percent Furfural and %70 of the initial COD. Conclusion: The results of this study showed that the ozone/persulfate process can be a suitable process for the removal of organic aromatic compounds including pollutants of interest.

  11. Removal of radioactive ions from nuclear waste solutions by electrodialysis

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, S [Radia Industries Co. Ltd., Takasaki, Gunma (Japan)

    1978-10-01

    Removal of radioactive ions was studied from low and medium level radioactive waste solutions by electrodialysis using ion exchange membranes. The test solutions contained /sup 137/Cs/sup +/, /sup 106/Ru/sup 3 +/ or fission products (F.P.) as active ions and NaCl, Na/sub 2/SO/sub 4/ or Ca(NO/sub 3/)/sub 2/ as inactive coexisting salts. The decontamination factor of the active ions was in the order: /sup 137/Cs/sup +/ (greater than 99%) > /sup 90/Sr/sup 2 +/ > F.P. > /sup 106/Ru/sup 3 +/. The dialysis time required to attain the saturation was the shortest for monovalent cations K/sup +/, Cs/sup +/ and Na/sup +/, intermediate for divalent cation Sr/sup 2 +/, and the longest for trivalent cation Ru/sup 3 +/. The ratio of the decontamination factor of an active ion eta sub( a) to the desalination factor of an inactive ion eta sub( b) was nearly equal to unity for /sup 24/Na, /sup 42/K, /sup 137/Cs and /sup 90/Sr. On the other hand, the apparent selective permeability of an active ion (A/sup +/) against Na/sup +/ ion, T sub(Na/sup +/) sup( a) was higher than unity for all the active ions tested, and was in the order of /sup 137/Cs > /sup 90/Sr > /sup 42/K > /sup 24/Na, where T sub(Na/sup +/) sup( a) is defined by the ratio of ..gamma..sub( a) to ..gamma..sub(Na/sup +/) with ..gamma..sub( a) being the ratio of dilution of A in the diluate the ..gamma..sub(Na/sup +/) being that of Na/sup +/ in the same diluate. The decontamination factor of the active ions did not depend significantly on the species and concentration of the coexistent salts or on the concentration of the active ions.

  12. Evaluation of the efficiency of denture cleaners for removing denture adhesives.

    Science.gov (United States)

    Harada-Hada, Kae; Hong, Guang; Abekura, Hitoshi; Murata, Hiroshi

    2016-12-01

    We developed a new scoring index for assessing the removability of denture adhesives and evaluated the removal efficiency of denture cleaners. Although our understanding of the importance of denture care is increasing, little is known about the effectiveness and efficiency of denture cleaners on denture adhesives. Therefore, guidelines for proper cleaning are necessary. We used five denture cleaner solutions on two cream adhesives, one powder adhesive and one cushion adhesive. After immersion in the denture cleaners for a designated time, we evaluated the area of the sample plate still covered by denture adhesive. Cream adhesives were removed more completely after immersion in majority of the denture cleaners than in water. Powder adhesive was removed more quickly than cream adhesives. Cushion adhesive was not removed by immersion in either the denture cleaners or water control. Some denture cleaners could liquefy cream adhesives more than water, but these differences were not observed in case of powder and cushion adhesives. © 2015 John Wiley & Sons A/S and The Gerodontology Association. Published by John Wiley & Sons Ltd.

  13. Evaluation of Iron and Manganese-Coated Pumice Application for the Removal of as(v from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Leila Babaie Far

    2012-12-01

    Full Text Available Arsenic contamination of water has been recognized as a serious environmental issue and there are reports on its epidemiological problems to human health. The objective of this study was to evaluate the performances of iron-coated pumice and manganese-coated pumice as the adsorbents for removing arsenate from aqueous solutions. The effect of various parameters such as adsorbent dose, contact time, pH and initial concentration on removal efficiency of arsenate were evaluated in batch mode. The data obtained from the kinetic studies were analyzed using kinetic models of pseudo-first-order and pseudo-second-order. In addition, two isotherm models of Freundlich and Langmuir were used to fit the experimental data. The results showed that the optimum dosage of iron-coated pumice and manganese-coated pumice for arsenate removal were 40 and 80 g/L whereas the adsorption process reached equilibrium after 80 and 100 min, respectively. The maximum removal efficiency of arsenate using the two adsorbents were both recorded in pH=3 as the removal efficiency gradually declinedfollowing every increase in pH values of the solution. Iron-coated pumice also showed to have high removal efficiency when the initial concentration of arsenate was high while the low concentration of arsenate was efficiently removed by manganese-coated pumice. Moreover, it was depicted that the adsorption kinetics by bothadsorbents followed pseudo-second order equation and the uptake data of arsenate were well fitted with Langmuir isotherm model. Therefore, it could be concluded that iron and manganese-coated pumice could beconsidered as suitable adsorbents for arsenate removal from aqueous solutions.

  14. Activated carbons employed to remove ionic liquids from aqueous solutions

    International Nuclear Information System (INIS)

    Hassan, S.; Farooq, A.; Ahmad, M.A.; Irfan, N.; Tufail, M.

    2011-01-01

    Imidazolium and pyridinium based ionic liquids (ILs) have been separated from aqueous solutions by adsorption using a raw Chinese activated carbon (CAC), a bleached Chinese activated carbon (BAC) and an acid treated Chinese activated carbon (AAC) as adsorbent. Adsorption isotherms data of ionic liquids on activated carbons has been obtained. The influence of both cations and anions was analyzed by studying three different ILs. The role of surface chemistry of the adsorbent was also examined using activated carbons modified by oxidative treatments. The BET surface area of activated carbons was measured by nitrogen adsorption. The results of this work indicate that activated carbon is an attractive adsorbent to remove ionic liquids from water streams. It has also been demonstrated that the adsorption of hydrophilic ionic liquids can be improved by modifying the amount and nature of oxygen groups on the activated carbon surface specially by increasing basic groups. The adsorption data for isotherms was studied at acidic, neutral and basic pH values. (author)

  15. Removal and adsorption characteristics of polyvinyl alcohol from aqueous solutions using electrocoagulation

    Energy Technology Data Exchange (ETDEWEB)

    Chou, Wei-Lung, E-mail: wlchou@sunrise.hk.edu.tw [Department of Safety, Health and Environmental Engineering, Hungkuang University, Sha-Lu, Taichung 433, Taiwan (China)

    2010-05-15

    The study was to investigate the performance of electrocoagulation (EC) for the efficient removal of polyvinyl alcohol (PVA) from aqueous solutions. Several parameters were evaluated to characterize the PVA removal efficiency, such as various electrode pairs, current densities, supporting electrolytes, temperatures, and initial electrolyte concentrations. The effects of the current density, supporting electrolyte, and temperature on the electrical energy consumption were also investigated. The experimental results indicate that a Fe/Al electrode pair is the optimum choice out of four different electrode pair combinations. The optimum current density, supporting electrolyte concentration, and temperature were found to be 5 mA cm{sup -2}, 0.008N NaCl, and 298 K, respectively. The PVA removal efficiency decreased with increasing in the initial concentrations. The kinetic studies indicated that the EC process was best described using pseudo-second-order kinetics. The experimental data were also compared to different adsorption isotherm models in order to describe the EC process. The adsorption of PVA was best fitted by the Langmuir adsorption isotherm model. Thermodynamic parameters such as the Gibbs free energy, enthalpy, and entropy indicated that the adsorption of PVA on metal hydroxides was feasible, spontaneous and endothermic in the temperature range of 288-318 K.

  16. Removal and adsorption characteristics of polyvinyl alcohol from aqueous solutions using electrocoagulation

    International Nuclear Information System (INIS)

    Chou, Wei-Lung

    2010-01-01

    The study was to investigate the performance of electrocoagulation (EC) for the efficient removal of polyvinyl alcohol (PVA) from aqueous solutions. Several parameters were evaluated to characterize the PVA removal efficiency, such as various electrode pairs, current densities, supporting electrolytes, temperatures, and initial electrolyte concentrations. The effects of the current density, supporting electrolyte, and temperature on the electrical energy consumption were also investigated. The experimental results indicate that a Fe/Al electrode pair is the optimum choice out of four different electrode pair combinations. The optimum current density, supporting electrolyte concentration, and temperature were found to be 5 mA cm -2 , 0.008N NaCl, and 298 K, respectively. The PVA removal efficiency decreased with increasing in the initial concentrations. The kinetic studies indicated that the EC process was best described using pseudo-second-order kinetics. The experimental data were also compared to different adsorption isotherm models in order to describe the EC process. The adsorption of PVA was best fitted by the Langmuir adsorption isotherm model. Thermodynamic parameters such as the Gibbs free energy, enthalpy, and entropy indicated that the adsorption of PVA on metal hydroxides was feasible, spontaneous and endothermic in the temperature range of 288-318 K.

  17. Removal of Cu(II) metal ions from aqueous solution by amine functionalized magnetic nanoparticles

    Science.gov (United States)

    Kothavale, V. P.; Karade, V. C.; Waifalkar, P. P.; Sahoo, Subasa C.; Patil, P. S.; Patil, P. B.

    2018-04-01

    The adsorption behavior of Cu(II) metal cations was investigated on the amine functionalized magnetic nanoparticles (MNPs). TheMNPs were synthesized by thesolvothermal method and functionalized with (3-Aminopropyl)triethoxysilane (APTES). MNPs were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and vibrating sample magnetometer (VSM). The MNPs have pure magnetite phase with particle size around 10-12 nm. MNPs exhibits superparamagnetic behavior with asaturation magnetization of 68 emu/g. The maximum 38 % removal efficiency was obtained for Cu(II) metal ions from the aqueous solution.

  18. AOM Characterization and Removal Efficiency Using Various SWRO Pretreatment Techniques

    KAUST Repository

    Namazi, Mohammed

    2017-12-01

    This study investigates the operation of dual media filter DMF during ambient and simulated algal bloom conditions, and the role of coagulation and dissolved air flotation (DAF) in mitigating the adverse effects of algal blooms on DMF performance. The study also highlights which AOM concentration as a function of biopolymer is critical to organic fouling in DMF pretreatment for Red Sea water desalination with RO. On the other hand, the present study has carried out another experiment on AOM fouling in comparison with bacterial organic matter (BOM) and humic organic matter (HOM) using two different pore sizes of UF ceramic membranes, 5 and 50 kDa. The main aim of this comparison is to examine fouling behavior and mechanism and removal efficiency. The study revealed that AOM can induce organic fouling in DMF during simulated algal bloom conditions at biopolymer concentrations as low as 0.2 mg C/L. DMF performance was strongly affected by AOM concentration as observed by flow rate decline through time. Liquid chromatography – organic carbon detection (LC-OCD) analysis showed higher removal rates of biopolymers than lower molecular weight fractions (i.e., humic substances, building blocks and low molecular weight neutrals) for all pretreatment scenarios. The study also indicated that while DMF performance was enhanced with coagulation and sedimentation, the most significant improvement in performance was observed for DMF operation preceded by coagulation and DAF. Hydraulic performance of DMF correlated well with biopolymers removal, with removal rates of 72%, 53% and 39%, for coagulation/DAF, coagulation/sedimentation, and no coagulation, respectively. For UF ceramic membranes, results showed that more TEP/organics were removed by the 5 kDa membranes compared to the 50 kDa membrane, which is accounted for lower MWCO. The UF 5 kDa membrane also showed low fouling formation than 50 kDa membrane for all of three types of organic matter tested. Analysis of the fouled

  19. The Application of Low-Cost Adsorbent for Reactive Blue 19 Dye Removal from Aqueous Solution: Lemna Minor

    Directory of Open Access Journals (Sweden)

    Davoud Balarak

    2015-10-01

    Full Text Available Background & Aims of the Study: Due to widespread use and adverse effect of dyes, the removal of dyes from effluents is necessary. This study was aimed to remove the reactive blue 19 dye removal from aqueous solution by dried Lemna minor. Materials and Methods:  The effect of various parameters including contact time, solution pH, adsorbent dosage and dye concentration was investigated in this experimental-lab study, Also, the isotherm and kinetic studies was performed for RB19 dye adsorption process. Results: The results indicated that RB19 dye removal efficiency increases by increasing of contact time and adsorbent dosage. The equilibrium time was 75 min ad the maximum dye removal efficiency was obtained in pH=3. Also, the dye removal efficiency decreases by increasing of pH and initial concentration. It was found that the equilibrium data was best follow by Langmuier isotherm. Also, the pseudo-second-kinetic model was best applicable for RB 19 dye adsorption. Conclusion: It can be concluded that the dried Lemna minor can be considered as an effective adsorbent to remove the RB19 dye.

  20. Efficient removal of sulfur hexafluoride (SF6) through reacting with recycled electroplating sludge.

    Science.gov (United States)

    Zhang, Jia; Zhou, Ji Zhi; Liu, Qiang; Qian, Guangren; Xu, Zhi Ping

    2013-06-18

    This paper reports that recycled electroplating sludge is able to efficiently remove greenhouse gas sulfur hexafluoride (SF6). The removal process involves various reactions of SF6 with the recycled sludge. Remarkably, the sludge completely removed SF6 at a capacity of 1.10 mmol/g (SF6/sludge) at 600 °C. More importantly, the evolved gases were SO2, SiF4, and a limited amount of HF, with no toxic SOF4, SO2F2, or SF4 being detected. These generated gases can be readily captured and removed by NaOH solution. The reacted solids were further found to be various metal fluorides, thus revealing that SF6 removal takes place by reacting with various metal oxides and silicate in the sludge. Moreover, the kinetic investigation revealed that the SF6 reaction with the sludge is a first-order chemically controlled process. This research thus demonstrates that the waste electroplating sludge can be potentially used as an effective removal agent for one of the notorious greenhouse gases, SF6.

  1. Aerobic granular biomass: a novel biomaterial for efficient uranium removal

    International Nuclear Information System (INIS)

    Nancharaiah, Y.V.; Joshi, H.M.; Mohan, T.V.K.; Venugopalan, V.P.; Narasimhan, S.V.

    2006-01-01

    Aerobic microbial granules, self-immobilized microbial consortia cultured in aerobically operated bioreactors, primarily consist of mixed species of bacteria ensconced in an extracellular polymeric matrix of their own creation. Such aerobically grown microbial granules have attracted considerable research interest in environmental biotechnology. In recent times, it has been demonstrated that the granules could be used for efficient degradation of recalcitrant organic compounds and for the treatment of a growing number of wastes. The objective of this study was to investigate whether aerobic granules could be used as novel biomass material for biosorption of uranium from aqueous solutions

  2. Efficient solutions from HVAC to offgrid

    International Nuclear Information System (INIS)

    Anon.

    2014-01-01

    Rio Tinto and Ingenero recently announced that agreement had been reached for the development of the Weipa Solar Photovoltaic Project in Queensland. First Solar will leverage its expertise in utility-scale grid integration and plant control systems to offer a FuelSmart solution that provides maximum fuel savings while maintaining system reliability. Combined with Ingenero's design and integration experience, the project will generate electricity for Rio Tinto Alcan's Weipa bauxite mine, processing facilities and township on the Western Cape York Peninsula

  3. Removal of NO from flue gas by aqueous chlorine-dioxide scrubbing solution in a lab-scale bubbling reactor.

    Science.gov (United States)

    Deshwal, Bal Raj; Jin, Dong Seop; Lee, Si Hyun; Moon, Seung Hyun; Jung, Jong Hyeon; Lee, Hyung Keun

    2008-02-11

    The present study attempts to clean up nitric oxide from the simulated flue gas using aqueous chlorine-dioxide solution in the bubbling reactor. Chlorine-dioxide is generated by chloride-chlorate process. Experiments are carried out to examine the effect of various operating variables like input NO concentration, presence of SO(2), pH of the solution and NaCl feeding rate on the NO(x) removal efficiency at 45 degrees C. Complete oxidation of nitric oxide into nitrogen dioxide occurred on passing sufficient ClO(2) gas into the scrubbing solution. NO is finally converted into nitrate and ClO(2) is reduced into chloride ions. A plausible reaction mechanism concerning NO(x) removal by ClO(2) is suggested. DeNO(x) efficiency increased slightly with the increasing input NO concentration. The presence of SO(2) improved the NO(2) absorption but pH of solution showed marginal effect on NO(2) absorption. NO(x) removal mechanism changed when medium of solution changed from acidic to alkaline. A constant NO(x) removal efficiency of about 60% has been achieved in the wide pH range of 3-11 under optimized conditions.

  4. Application of agricultural fibers in pollution removal from aqueous solution

    International Nuclear Information System (INIS)

    Mahvi, A. H.

    2008-01-01

    Discharging different kinds of wastewater and polluted waters such as domestic, industrial and agricultural wastewaters into environment, especially to surface water, can cause heavy pollution of this body sources. With regard to increasing effluent discharge standards to the environment, high considerations should be made when selecting proper treatment processes. Any of chemical, biological and physical treatment processes have its own advantages and disadvantages. It should be kept in mind that economical aspects are important, too. In addition, employing environment friendly methods for treatment is emphasized much more these days. Application of some waste products that could help in this regard, in addition to reuse of these waste materials, can be an advantage, Agricultural fibers are agricultural wastes and are generated in high amounts. The majority of such materials is generated in developing countries and, since they are very cheap, they can be employed as bio sorbents in water and wastewater applications. Polluted surface waters, different wastewaters and partially treated wastewater may be contaminated by heavy metals or some organic matters and these waters should be treated to reduce pollution. The results of investigations show high efficiency of agricultural fibers in heavy metal and phenol removal. In this paper, some studies conducted by the author of this article and other investigators are reviewed

  5. Assessment of Some Synthetic Polymers for the Removal of Pollutants from Waste Solutions

    International Nuclear Information System (INIS)

    Ayoub, R.; El-Naggar, H.A.; Ezz EL-Din, M.R.; Moussa, A.R.

    1999-01-01

    The sorption capacity of 134 Cs, 60 Co, 152+154 Eu and Cu (II) by three prepared has been studied using batch and column techniques. The three polymers are polyacrylic acid (PAA), polyacrylamide-acrylic acid (PAM-AA) and polyacrylamide-N-vinyl-2-pyrraldone (PAM-NVP). These polymers were prepared by gamma radiation initiated polymerization of their corresponding monomer solutions. The appropriate value for V/m ratio (volume of solution to mass of polymer) that can result in reasonably high distribution coefficient, Kd, was determined. The variation of the amount sorbed of the isotope per gram polymer (X/m) with concentration of the relevant element was found to follow a Frendlich type isotherm. The distribution coefficient, Kd, of the studied element was found to be affected by the ph of the solution. The desorption of the investigated metal ions is also studied at different ph. For column studies, the percent removed of the radioisotopes 134 Cs, 60 Co, ( 152+154 )Eu in addition to some heavy metals ions such as Pb, Cd, Zn and Cu(II) was determined. More than 95% of these elements were removed when 3 beds column of PAA or PAM-AA was used. From the data obtained we can conclude that the polymer PAA or PAM-AA can considered as an efficient sorbent for metal cations from their aqueous solution

  6. High-efficiency SO2 removal in utility FGD systems

    International Nuclear Information System (INIS)

    Phillips, J.L.; Gray, S.; Dekraker, D.

    1995-01-01

    The U.S. Department of Energy (DOE) and the Electric Power Research Institute (EPRI) have contracted with Radian Corporation to conduct full-scale testing, process modeling, and economic evaluations of six existing utility flue gas desulfurization (FGD) systems. The project objective is to evaluate low capital cost upgrades for achieving up to 98% sulfur dioxide (SO 2 ) removal efficiency in a variety of FGD system types. The systems include dual-loop, packed absorbers at Tampa Electric Company's Big Bend Station; cocurrent, packed absorbers at Hoosier Energy's Merom Station; dual-loop absorbers with perforated-plate trays at Southwestern Electric Power Company's Pirkey Station; horizontal spray absorbers at PSI Energy's Gibson Station; venturi scrubbers at Duquesne Light's Elrama Station; and open stray absorbers at New york State Electric and Gas Corporations's (NYSEG's) Kintigh Station. All operate in an inhibited-oxidation mode except the system at Big Bend (forced oxidation), and all use limestone reagent except the Elrama system (Mg-lime). The program was conducted to demonstrate that upgrades such as performance additives and/or mechanical modifications can increase system SO 2 removal at low cost. The cost effectiveness of each upgrade has been evaluated on the basis of test results and/or process model predictions for upgraded performance and utility-specific operating and maintenance costs. Results from this upgraded performance and utility-specific operating and maintenance costs. Results from this program may lead some utilities to use SO 2 removal upgrades as an approach for compliance with phase 2 of Title IV of the Clean Air Act Amendments (CAAA) of 1990. This paper summarizes the results of testing, modeling, and economic evaluations that have been completed since July, 1994

  7. Mixed Contaminants Removal Efficiency Using Bio-FeS Nanoparticles.

    Science.gov (United States)

    Seo, Hyunhee; Roh, Yul

    2018-02-01

    Advances in nanotechnology has provided diverse industrial applications including an environmental remediation field. In particular, bio-nanotechnology gives extended eco-friendly remediation practice. Among diverse bio-nanoparticles synthesized by microorganisms, the iron based nanoparticles (NPs) are of great interest because of their availability, low cost and toxicity to human health and the environment. In this study, iron based nanoparticles were biologically synthesized and mineralogically identified. Also, the removal efficiency of mixed contaminants, high As(III)-low Cr(VI) and high As(V)-low Cr(VI), using these bio-nanoparticles were conducted. As a result, biologically synthesized NPs were identified as FeS complex and their catalytic capacity showed highly effective to immobilize more than 97% of mixed contaminants by adsorption/mineralization.

  8. Poorly crystalline hydroxyapatite: A novel adsorbent for enhanced fulvic acid removal from aqueous solution

    Science.gov (United States)

    Wei, Wei; Yang, Lei; Zhong, Wenhui; Cui, Jing; Wei, Zhenggui

    2015-03-01

    In this study, poorly crystalline hydroxyapatite (HAP) was developed as an efficient adsorbent for the removal of fulvic acid (FA) from aqueous solution. Surface functionality, crystallinity, and morphology of the synthetic adsorbent were studied by Fourier-transformation infrared (FT-IR) spectroscopy, powder X-ray diffraction (XRD) and transmission electron microscopy (TEM). The effects of various parameters such as crystallinity of adsorbent, contact time, adsorbent dosage, pH, initial adsorbate concentration, temperature, ionic strength and the presence of alkaline earth metal ions on FA adsorption were investigated. Results indicated that the nanosized HAP calcined at lower temperature was poorly crystalline (Xc = 0.23) and had better adsorption capacity for FA than those (Xc = 0.52, 0.86) calcined at higher temperature. FA removal was increased with increases of adsorbent dosage, temperature, ionic strength and the presence of alkali earth metal ions, but decreased as the pH increased. Kinetic studies showed that pseudo-second-order kinetic model better described the adsorption process. Equilibrium data were best described by Sips models, and the estimated maximum adsorption capacity of poorly crystalline HAP was 90.20 mg/g at 318 K, displaying higher efficiency for FA removal than previously reported adsorbents. FT-IR results revealed that FA adsorption over the adsorbent could be attributed to the surface complexation between the oxygen atom of functional groups of FA and calcium ions of HAP. Regeneration studies indicated that HAP could be recyclable for a long term. Findings of the present work highlight the potential for using poorly crystalline HAP nanoparticles as an effective and recyclable adsorbent for FA removal from aqueous solution.

  9. Efficient Removal of Cationic and Anionic Radioactive Pollutants from Water Using Hydrotalcite-Based Getters.

    Science.gov (United States)

    Bo, Arixin; Sarina, Sarina; Liu, Hongwei; Zheng, Zhanfeng; Xiao, Qi; Gu, Yuantong; Ayoko, Godwin A; Zhu, Huaiyong

    2016-06-29

    Hydrotalcite (HT)-based materials are usually applied to capture anionic pollutants in aqueous solutions. Generally considered anion exchangers, their ability to capture radioactive cations is rarely exploited. In the present work, we explored the ability of pristine and calcined HT getters to effectively capture radioactive cations (Sr(2+) and Ba(2+)) which can be securely stabilized at the getter surface. It is found that calcined HT outperforms its pristine counterpart in cation removal ability. Meanwhile, a novel anion removal mechanism targeting radioactive I(-) is demonstrated. This approach involves HT surface modification with silver species, namely, Ag2CO3 nanoparticles, which can attach firmly on HT surface by forming coherent interface. This HT-based anion getter can be further used to capture I(-) in aqueous solution. The observed I(-) uptake mechanism is distinctly different from the widely reported ion exchange mechanism of HT and much more efficient. As a result of the high local concentrations of precipitants on the getters, radioactive ions in water can be readily immobilized onto the getter surface by forming precipitates. The secured ionic pollutants can be subsequently removed from water by filtration or sedimentation for safe disposal. Overall, these stable, inexpensive getters are the materials of choice for removal of trace ionic pollutants from bulk radioactive liquids, especially during episodic environmental crisis.

  10. Efficiency of lipopeptide biosurfactants in removal of petroleum hydrocarbons and heavy metals from contaminated soil.

    Science.gov (United States)

    Singh, Anil Kumar; Cameotra, Swaranjit Singh

    2013-10-01

    This study describes the potential application of lipopeptide biosurfactants in removal of petroleum hydrocarbons and heavy metals from the soil samples collected from industrial dumping site. High concentrations of heavy metals (like iron, lead, nickel, cadmium, copper, cobalt and zinc) and petroleum hydrocarbons were present in the contaminated soil samples. Lipopeptide biosurfactant, consisting of surfactin and fengycin was obtained from Bacillus subtilis A21. Soil washing with biosurfactant solution removed significant amount of petroleum hydrocarbon (64.5 %) and metals namely cadmium (44.2 %), cobalt (35.4 %), lead (40.3 %), nickel (32.2 %), copper (26.2 %) and zinc (32.07 %). Parameters like surfactant concentration, temperature, agitation condition and pH of the washing solution influenced the pollutant removing ability of biosurfactant mixture. Biosurfactant exhibited substantial hydrocarbon solubility above its critical micelle concentration. During washing, 50 % of biosurfactant was sorbed to the soil particles decreasing effective concentration during washing process. Biosurfactant washed soil exhibited 100 % mustard seed germination contradictory to water washed soil where no germination was observed. The results indicate that the soil washing with mixture of lipopeptide biosurfactants at concentrations above its critical micelle concentration can be an efficient and environment friendly approach for removing pollutants (petroleum hydrocarbon and heavy metals) from contaminated soil.

  11. Comparision of Chitosan Function as Adsorbent for Nitrate Removal Using Synthetic Aqueous Solution and Drinking Water

    Directory of Open Access Journals (Sweden)

    Mohammad Norisepehr

    2013-12-01

    Full Text Available Background & Objectives: Nitrate and nitrite compounds pollution of groundwater resources in recent years which recently their mean concentration due to enhancement of different kind of municipal, industrial and agriculture waste water, were increased. The most common source of nitrates entering the water include chemical fertilizers and animal manure in agriculture, septic tank effluent, wastewater, wastewater treatment plants, animal and plant residue analysis on the ground of non-sanitary disposal of solid waste and the use of absorbing wells for sewage disposal. Materials and methods: This experimental study is applied to the nitrate removal using chitosan in laboratory scale at ambient temperature and the design of the system was Batch. Effects of parameters such as pH, contact time, initial concentration and adsorbent concentration of nitrate on nitrate removal from aqueous solution was studied. Results: Function of chitosan in synthetic aqueous solution and drinking water according to the slurry system results, the optimum condition was obtained at pH=4, 20 min contact time and increasing the initial concentration of nitrate enhance the adsorption capacity of chitosan. Also optimum dosage of adsorbent was obtained at 0.5 g/l. The data obtained from the experiments of adsorbent isotherm were analyzed using Langmuir and Freundlich isotherm models. The Langmuir equation was found to be the best fitness with the experimental data (R2>0.93. Conclusion: Although efficiency of Nitrate removal in synthetic aqueous solution was better than drinking water, adsorption process using chitosan as an option for the design and selection nitrate removal should be considered in order to achieve environmental standards.

  12. Activation of Graphene Oxide with Hydrochloric Acid for Nitrate Removal from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Abolghasem Alighardashi

    2017-11-01

    Full Text Available Long-term drinking of nitrate-contaminated water poses a serious risk to human health. The present study explores the possibility of enhancing the adsorption capacity of graphene oxide via activation with hydrochloric acid for nitrate removal from aqueous solutions. Experiments were performed in a batch reactor in which such major factors as pH, reaction time, and concentrations of both graphene oxide (GO and activated graphene oxide (AGO were used as variables. Nitrate removal efficiency was investigated using the One-Way ANOVA statistical test and SPSS-16 software. The chemical composition and solid structure of the synthesized AGO were analyzed using FE-SEM coupled with energy dispersive spectrometry (EDS. The micropore volumes of the samples were determined using the BET and BJH. The predominant composition (52% of the synthesized AGO was C and its mean pore diameter was 26.896 nm. The maximum adsorption capacity of AGO was estimated at 3333.33 mg/g. Based on the results, the AGO nano-structure may be recomended as a new means for nitrate removal from aqueous solutions.

  13. Fixed-bed column study for 90Sr removal from solution by sunflower straw

    International Nuclear Information System (INIS)

    Ai Lian; Luo Xuegang; Lin Xiaoyan; Li Wenming

    2014-01-01

    This paper deals with removal of strontium ions from solution by sunflower straw. Metal sorption performance of the packed column was assessed under variable operating conditions, such as, bed depths, flow rates and initial influent strontium concentration. It was found that the breakthrough time and the depletion time were extended with increase of bed heights but obviously shortened with increase of influent concentration and flow rates, respectively. The equilibrium uptake (q e(exp) ) of sunflower straw increased with increase in initial influent strontium concentration and flow rates but decreased with increase in bed depth, respectively. The data in regard to the effect of bed depths were fitted well to the Bohrat-Adams model. The saturated column was successfully regenerated by 0.1 mol/L hydrogen chloride solution and sunflower straw could be reused in strontium removal. The results indicated that the column could efficiently remove strontium ions from real industrial effluents, and hence the sunflower straw is a good candidate for commercial application. (authors)

  14. Investigation of Pb(II Removal from Aqueous Solutions Using Modified Nano Zero-Valent Iron Particles

    Directory of Open Access Journals (Sweden)

    Amirhossein Ramezanpoor

    2014-05-01

    Full Text Available This research was conducted in experimental scale with the aim of investigation effect of polyacrylic acid-stabilized zero-valent iron nanoparticles (PAA-nZVI on lead removal from aqueous solution. In this regards, NZVI was synthesized with polyacrylic acid and their size and morphological characteristics were examined via X-ray diffraction (XRD, Scanning Electron Microscopy (SEM and Fourier Transmission Infrared Spectroscopy (FTIR. To study the effect of PAA-nZVI on lead removal, pH of aqueous solution, contact time, PAA-NZVI concentration  and initial Pb(II concentration were considered as variables. Furthermore, the experimental data of Pb(II  removal were fitted using three kinetic models, namely Zero-order, First-order and Second-order.The results of experiments showed that maximum Pb(II removal efficiency was observed at pH=5, 15 min contact time and 5 g/L PAA-nZVI concentration. Moreover, the results of kinetic studies indicated that among all applied kinetic models, First-order kinetic model had more better prediction than other kinetic models ofPb(II removal. Based on the results of present research, PAA-NZVI is an efficient agent to remove Pb(II from aqueous solutions.

  15. Removal of phenol from aqueous solution using polymer inclusion membrane based on mixture of CTA and CA

    Science.gov (United States)

    Benosmane, Nadjib; Boutemeur, Baya; Hamdi, Safouane M.; Hamdi, Maamar

    2018-03-01

    Nowadays, there are increasingly stringent regulations requiring more and more treatment of industrial effluents to generate product waters which could be easily reused or disposed of to the environment without any harmful effects. In the present work, the removal of phenol from aqueous solution across polymer inclusion membrane (PIM), based on mixture of cellulose triacetate and cellulose acetate as support (75/25%), calix[4]resorcinarene derivative as a carrier and 2-nitrophenyl octyl ether (2-NPOE) as plasticizer was investigated. The experimental part of this investigation involved the influence of carrier nature, plasticizer concentration, pH phases, and phenol initial concentration on the removal efficiency of phenol from synthetic wastewater. A PIM containing 0.1 g (of mixture polymer), (0.15 g/g mixture of polymer) of carrier and (0.03 ml/g mixture of polymer) of 2-NPOE provided the highest percentage of phenol removal efficiency over a 6-day transport; the removal was found to be about 95%, indeed the removal was found to be highly dependent of pH phases. The feed solution in these transport experiments was at pH 2, while the stripping solution contained 0.20 M NaOH. This study claims that the PIM with a mixture of cellulose derivatives can be used effectively to remove phenols from wastewaters.

  16. A new chemical system solution for acid gas removal

    Energy Technology Data Exchange (ETDEWEB)

    Seiler, M.; Rolker, J.; Witthaut, D.; Schulze, S. [Evonik Industries AG, Hanau (Germany); Buchholz, S. [Evonik Industries AG, Marl (Germany)

    2012-07-01

    An energy-efficient absorbent formulation fors eparating acid gases (e.g. CO{sub 2}, H2S) from gas streams such as natural gas, syngas or flue gas is important for a number of industrial applications. In many cases, a substantial share of their costs is driven by the operational expenditure (OPEX) of the CO{sub 2} separation unit. One possible strategy for reducing OPEX is the improvement of the absorbent performance. Although a number of absorbents for the separation of CO{sub 2} from gas streams exist, there is still a need to develop CO{sub 2} absorbents with an improved absorption performance, less corrosion and foaming, no nitrosamine formation, lower energy requirement and therefore less OPEX. This contribution aims at giving a brief state-of-the-art overview followed by an introduction and performance characterization of a new family of amine-based CO{sub 2} absorbents. High cyclic capacities in the range of 2.9 to 3.2 mol CO{sub 2} kg{sup -1} absorbent and low absorption enthalpies of about -30 kJ mol{sup -1} allow for significant savings in the regeneration energy of the new absorbent system. Calculations with the modified Kremser model indicate a reduction in the specific reboiler heat duty of 45 %. Moreover, the high-performance absorbents developed show much lower corrosion rates than state-of-the-art solutions that are currently employed. (orig.)

  17. Performance of ultrasonic and hydrogen peroxide technologies in removal of Bisphenol A from Aqueous solution

    Directory of Open Access Journals (Sweden)

    MH Dehghani

    2016-05-01

    Full Text Available Introduction:BPA is a non biodegradable antioxidant that has greatly hazardous for human and animals health. and Because of the eliminating alone fewness amount of the BPA during the wastewater treatment, wastewater that contains BPA can be source of pollution in aqueous solution. The objective of this study was Performance of ultrasonic and H2O2 technologies in removal of BPA from aqueous solution. Methods:Experiments of sonochemical was carried out with use of unit ultrasonicator (Elma, which in the two power 300 and 500W, frequencies at 35 and 130KHz. Hydrogen Peroxide in concentrations at 5, 15 and 30mg/lit was applied. Initial concentration BPA at limits 2, 5, 20 and 50 mg/lit which For measuring concentration of BPA used from Spectrometer UV/VIS Lambada 25 Perkin Elmer, Shelton unit. Results:The results demonstrated that hybrid ultrasonic and peroxide Hydrogen processes with Efficiency 98.65%,  has the highest efficiency in the removal of BPA. The most decomposition rate achieved at the frequency of 130 KHz and 500W assisted by 30mg/lit H2O2 at pH 11. Also the results demonstrated that with pH increase destruction rate BPA the increased by any three processes (ultrasonic, H2O2 and both hybrid. Conclusion:The results demonstrated that hybrid ultrasonic and peroxide Hydrogen processes can be used as a clean method and friendly environment for waters treatment are contains desirable BPA.

  18. Efficiency of final irrigation of root canal in removal of smear layer

    Directory of Open Access Journals (Sweden)

    Mitić Aleksandar

    2009-01-01

    Full Text Available Introduction A smear layer forms on the root canal walls as the consequence of root instrumentation. The smear layer formed in such a way considerably influences the quality of root obturation and endodontic treatment outcome. Objective The aim of this study was to ultrastructurally analyze the surface of intracanal dentine after removal of the smear layer by the solution of doxycycline, citric acid and detergent Tween-80 (MTAD. Methods The study involved 60 single-rooted, extracted, human teeth divided into four groups. All samples were instrumented by a step-back technique and manual K-files, and rinsed during instrumentation by 2% CHX and H2O2. The first group of samples was exclusively rinsed by CHX and H2O2; in the second group, besides using CHX and H2O2, MTAD solution was used for the final irrigation. The samples which were rinsed by distilled water (+ control and the samples rinsed by 5.25% NaOCl and 17% Na EDTA (-control served as control groups. All samples were observed under the scanning electronic microscope JEOL-JSM-5300. The coronary, middle and apex thirds of the radix region were analyzed. Results The obtained results of the SEM analysis showed that the application of 2% chlorhexidine and hydrogen peroxide did not give clear dentine walls, and the smear layer could not be removed completely. The application of the same combination (CHX and H2O2, added by the final MTAD irrigation solution, led to the efficient removal of the smear layer, while the morphological structure of dentine surface remained unchanged. Statistical analysis showed that canal walls in the experimental group with MTAD as the final irrigation were significantly clearer compared to the control group (p<0.001. Conclusion Based on the obtained results, it can be concluded that MTAD is an efficient solution for the final irrigation of the canal system.

  19. Energy efficient SO2 removal from flue gases using the method Wellman-Lord

    International Nuclear Information System (INIS)

    Dzhonova-Atanasova, D.; Razkazova-Velkova, E.; Ljutzkanov, L.; Kolev, N.; Kolev, D.

    2013-01-01

    Full text: Investigations on development of energy efficient technology for SO 2 removal from flue gases of combustion systems by using the method Wellman-Lord are presented. It is characterized by absorption of sulfur dioxide with sodium sulfite solution, which reacts to form sodium bisulfite. The absorber is a packed column with multiple stages. After evaporation of the solution, SO 2 and sodium sulfite are obtained. The latter is dissolved in water from condensation of the steam carrying SO 2 from the evaporator. The regenerated solution returns in the absorber. The SO 2 removed from the flue gases is obtained as a pure product for use in chemical, food or wine production. The data discussed in the literature sources on flue gas desulfurization demonstrate the predominance of the methods with lime or limestone as absorbent, due to higher capital investments associated with the method of Wellman-Lord. A technological and economical evaluation of this regenerative method is presented in comparison to the non-regenerative gypsum method, using data from the existing sources and our own experience from the development of an innovative gypsum technology. Three solutions are discussed for significant enhancement of the method efficiency on the basis of a considerable increasing of the SO 2 concentration in the saturated absorbent. The improved method uses about 40% less heat for absorbent regeneration, in comparison to the existing applications of the method Wellman-Lord, and gives in addition the possibility to regenerate 95% of the consumed heat for heating water streams to about 90°C. Moreover, the incorporation in the installation of our system with contact economizers of second generation, already in industrial application, enables utilization of the waste heat of the flue gases for district heating. The employment of this system also leads to significant decreasing of the NO x emissions. key words: SO 2 removal, flue gases, absorption

  20. Removal of Cr6 + and Ni2+ from aqueous solution using bagasse and fly ash.

    Science.gov (United States)

    Rao, M; Parwate, A V; Bhole, A G

    2002-01-01

    Raw bagasse and fly ash, the waste generated in sugar mills and boilers respectively have been used as low-cost potential adsorbents. Raw bagasse was pretreated with 0.1N NaOH followed by 0.1N CH3COOH before its application. These low-cost adsorbents were used for the removal of chromium and nickel from an aqueous solution. The kinetics of adsorption and extent of adsorption at equilibrium are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental system. The effect of hydrogen ion concentration, contact time, sorbent dose, initial concentrations of adsorbate and adsorbent and particle size on the uptake of chromium and nickel were studied in batch experiments. The Sorption data has been correlated with Langmuir, Freundlich and Bhattacharya and Venkobachar adsorption models. The efficiencies of adsorbent materials for the removal of Cr(VI) and Ni(II) were found to be between 56.2 and 96.2% and 83.6 and 100%, respectively. These results were obtained at the optimized conditions of pH, contact time, sorbent dose, sorbate concentration of 100 mg/l and with the variation of adsorbent particles size between 0.075 and 4.75 mm. The order of selectivity is powdered activated carbon > bagasse > fly ash for Cr(VI) removal and powdered activated carbon > fly ash > bagasse for Ni(II) removal.

  1. Investigation of Cyanide Removal from Aqueous Solution Using Precipitation Process (FeCl3

    Directory of Open Access Journals (Sweden)

    A. Jonidi Jafari

    2013-02-01

    Full Text Available Background and Objectives: Cyanide is a toxic pollutant that is can be discharged from different industries such as iron and steel industry, coal mining and metal plating. Presence of this toxin in water and wastewater is a serious hazard and lead to undesirable effects on both the environment and human. Thus, its concentration control is essential for human health. The aim of this study was investigation of Cyanide Removal from aqueous solution using precipitation process (FeCl3. Material and Methods: This study is an experimental study in lab scale that was carried out in a batch system by jartest. Variations of this study including pH, FeCl3 concentration, reaction time and desired concentration of cyanide were investigated. Data were analyzed using Excel (version 2007 software. Results: The results of this research were showed that Cyanide with initial concentration of 10 mg/l in precipitation process was removed by 40% (conditions pH=90, FeCl3=0.4 g/l and the time 60 minutes. Also, the precipitation process efficiency to cyanide removal decreased of 40 to 23%, by increasing of the initial cyanide concentration of 10 to 15 mg/l. Conclusion: Precipitation process can be considered as a suitable alternative for recovery of cyanide to be re-used. Although, this process has limitations for treat total cyanide to environmental standards level. So, it is better be used in combination with other processes of these contaminants removal.

  2. Persimmon leaf bio-waste for adsorptive removal of heavy metals from aqueous solution.

    Science.gov (United States)

    Lee, Seo-Yun; Choi, Hee-Jeong

    2018-03-01

    The aim of this study was to investigate heavy metal removal using waste biomass adsorbent, persimmon leaves, in an aqueous solution. Persimmon leaves, which are biomaterials, have a large number of hydroxyl groups and are highly suitable for removal of heavy metals. Therefore, in this study, we investigated the possibility of removal of Cu, Pb, and Cd in aqueous solution by using raw persimmon leaves (RPL) and dried persimmon leaves (DPL). Removal of heavy metals by RPL and DPL showed that DPL had a 10%-15% higher removal than RPL, and the order of removal efficiency was found to be Pb > Cu > Cd. The pseudo-second order model was a better fit to the heavy metal adsorption experiments using RPL and DPL than the pseudo-first order model. The adsorption of Cu, Pb, and Cd by DPL was more suitable with the Freundlich isothermal adsorption and showed an ion exchange reaction which occurred in the uneven adsorption surface layer. The maximum adsorption capacity of Cu, Pb, and Cd was determined to be 19.42 mg/g, 22.59 mg/g, and 18.26 mg/g, respectively. The result of the adsorption experiments showed that the n value was higher than 2 regardless of the dose, indicating that the heavy metal adsorption on DPL was easy. In the thermodynamic experiment, ΔG° was a negative value, and ΔH° and ΔS° were positive values. It can be seen that the heavy metal adsorption process using DPL was spontaneous in nature and was an endothermic process. Moreover, as the temperature increased, the adsorption increased, and the affinity of heavy metal adsorption to DPL was very good. This experiment, in which heavy metals are removed using the waste biomass of persimmon leaves is an eco-friendly new bioadsorbent method because it can remove heavy metals without using chemicals while utilizing waste recycling. Copyright © 2018 Elsevier Ltd. All rights reserved.

  3. Efficient removal of pathogenic bacteria and viruses by multifunctional amine-modified magnetic nanoparticles.

    Science.gov (United States)

    Zhan, Sihui; Yang, Yang; Shen, Zhiqiang; Shan, Junjun; Li, Yi; Yang, Shanshan; Zhu, Dandan

    2014-06-15

    A novel amine-functionalized magnetic Fe3O4-SiO2-NH2 nanoparticle was prepared by layer-by-layer method and used for rapid removal of both pathogenic bacteria and viruses from water. The nanoparticles were characterized by TEM, EDS, XRD, XPS, FT-IR, BET surface analysis, magnetic property tests and zeta-potential measurements, respectively, which demonstrated its well-defined core-shell structures and strong magnetic responsivity. Pathogenic bacteria and viruses are often needed to be removed conveniently because of a lot of co-existing conditions. The amine-modified nanoparticles we prepared were attractive for capturing a wide range of pathogens including not only bacteriophage f2 and virus (Poliovirus-1), but also various bacteria such as S. aureus, E. coli O157:H7, P. aeruginosa, Salmonella, and B. subtilis. Using as-prepared amine-functionalized MNPs as absorbent, the nonspecific removal efficiency of E. coli O157:H7 or virus was more than 97.39%, while it is only 29.8% with Fe3O4-SiO2 particles. From joint removal test of bacteria and virus, there are over 95.03% harmful E. coli O157:H7 that can be removed from mixed solution with polyclonal anti-E. coli O157:H7 antibody modified nanoparticles. Moreover, the synergy effective mechanism has also been suggested. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. Effects of additives on 2,4,6-trinitrotoluene (TNT) removal and its mineralization in aqueous solution by gamma irradiation

    International Nuclear Information System (INIS)

    Lee, Byungjin; Jeong, Seung-Woo

    2009-01-01

    The effects of additives (i.e., methanol, EDTA, mannitol, thiourea, nitrous oxide, oxygen and ozone) on gamma irradiation of 2,4,6-trinitrotoluene (TNT) were investigated to elucidate the initial reaction mechanism of TNT degradation and suggest an practical method for complete by-product removal. All additives, except thiourea, significantly increased the TNT removal efficiency by gamma irradiation. The overall results of the additive experiments implied that the TNT decomposition would be initiated by ·OH, e aq - , and HO 2 ·/O 2 · - , and also implied that ·H did not have any direct effect on the TNT decomposition. Additions of methanol and nitrous oxide were more effective in TNT removal than the other additives, achieving complete removal of TNT at doses below 20 kGy. Total organic carbon (TOC) of the irradiated solution was analyzed to evaluate the degree of TNT mineralization under the additive conditions. TOC under the nitrous oxide addition was removed rapidly, and complete TNT mineralization was thus achieved at 50 kGy. Methanol addition was very effective in the TNT removal, but it was not effective in reduction in TOC. Trinitrobenzene (TNB), oxalic acid and glyoxalic acid were detected as radiolytic organic by-products, while ammonia and nitrate were detected as radiolytic inorganic by-products. The most efficient TNT removal and its mineralization by gamma irradiation would be achieved by supersaturating the solution with nitrous oxide before irradiation.

  5. Investigation of the removal of chromium (VI by Nanocomposites Chitosan-tragacanth solution from aqueous solution

    Directory of Open Access Journals (Sweden)

    Adel Almasi Nahnaji

    2016-03-01

    Full Text Available Background: The aim of this study was to investigate the removal of chromium (VI by Nanocomposites Chitosan-tragacanth solution from aqueous solution. Methods: In this study, chitosan-tragacanth nanocomposites were synthesized and analyzed by electron microscopy (SEM, (TEM and Fourier transform spectroscopy (FT-IR for the size and shape of the surface. The nano-composite of chitosan-tragacanth, for the adsorption of chromium (VI in aqueous solution was used as adsorbent. Results: The optimum conditions with multiple experiments to enhance the absorption were evaluated. The highest absorption of Cr (VI was occurred in the adsorbent dosage of 0.2 g, 8 ppm concentration of chromium ions, the pH=6 and also retention time of 50 min; in 298 ˚K temperature. After determining optimal conditions of adsorption, isotherms equations and study and thermodynamic parameters were applied. Adsorption process of chromium (VI on nano-composite chitosan - Tragacanth was conformed with Temkin isotherm. Conclusion: The thermodynamic parameters such as standard Gibbs free energy changes, changes in enthalpy and entropy changes in the standard showed that the adsorption process of Cr (VI is spontaneous and heating, and kinetics studies of models Lagergren, Ho , Alovich and intraparticle is used, the results show that the adsorption kinetics follows the pseudo-second order.

  6. Efficient removal of chromate and arsenate from individual and mixed system by malachite nanoparticles

    International Nuclear Information System (INIS)

    Saikia, Jiban; Saha, Bedabrata; Das, Gopal

    2011-01-01

    Graphical abstract: Malachite nanoparticles of 100-150 nm, have been efficiently and for the first time used as an adsorbent for the removal of toxic arsenate and chromate in pH range 4-5. - Abstract: Malachite nanoparticles of 100-150 nm have been efficiently and for the first time used as an adsorbent for the removal of toxic arsenate and chromate. We report a high adsorption capacity for chromate and arsenate on malachite nanoparticle from both individual and mixed solution in pH ∼4-5. However, the adsorption efficiency decreases with the increase of solution pH. Batch studies revealed that initial pH, temperature, malachite nanoparticles dose and initial concentration of chromate and arsenate were important parameters for the adsorption process. Thermodynamic analysis showed that adsorption of chromate and arsenate on malachite nanoparticles is endothermic and spontaneous. The adsorption of these anions has also been investigated quantitatively with the help of adsorption kinetics, isotherm, and selectivity coefficient (K) analysis. The adsorption data for both chromate and arsenate were fitted well in Langmuir isotherm and preferentially followed the second order kinetics. The binding affinity of chromate is found to be slightly higher than arsenate in a competitive adsorption process which leads to the comparatively higher adsorption of chromate on malachite nanoparticles surface.

  7. Removal of Cd+2 from aqueous solutions onto polypyrrole coated reticulated vitreous carbon eletrodes

    Directory of Open Access Journals (Sweden)

    Tramontina Jucelânia

    2001-01-01

    Full Text Available The development of simple methods for removal of heavy metals from aqueous samples is a relevant field of research. In this connection, the electrodeposition of the Cd+2 ion, one of the most toxic species for animals and human beings, was investigated in aerated pH 4.8 sulfuric-sulfate solutions. In potentiostatic conditions, the maximum rate of cadmium deposition at a neutral polypyrrole (PPy0 coated reticulated vitreous carbon (RVC working electrode occurs at -3.0 V vs. the saturated calomel reference electrode (SCE. Moreover, the conversion rate depends both on the applied potential and on the mass transport regime, and, for solutions containing 10 mg L-1 of Cd2+, the highest removal efficiency achieved is 84% after 90 min of electrolysis. The concentration decay of the Cd+2 ion in the solution was monitored by anodic stripping voltammetry (ASV at a hanging mercury drop electrode. Besides, metallic cadmium deposited onto the polypyrrole modified RVC electrode was evidenced by Scanning Electron Microscopy (SEM analysis using the backscattered electron image (BEI technique and by Energy Dispersive Spectrometry (EDS.

  8. Tentacle carrier for immobilization of potato phenoloxidase and its application for halogenophenols removal from aqueous solutions

    International Nuclear Information System (INIS)

    Lončar, Nikola; Vujčić, Zoran

    2011-01-01

    Highlights: ► We synthesized novel immobilization carrier from reused DEAE-cellulose. ► We used it for immobilization of PPO through coordinative bonding with copper ions. ► Immobilized PPO showed better characteristics than soluble PPO. ► TC-PPO removed over 90% of halogenophenols at concentration of 100 mg/L. - Abstract: Halogenated compounds represent one of the most dangerous environmental pollutants, due to their widespread usage as biocides, fungicides, disinfectants, solvent and other industrial chemicals. Immobilization of a protein through coordinate bonds formed with divalent metal ions is becoming an attractive method due to its reversible nature, since the protein may be easily removed from the support matrix through interruption of the protein–metal bond hence giving inherently cleaner and cheaper technology for wastewater treatment. We have synthesized novel ‘tentacle’ carrier (TC) and used it for immobilization of partially purified potato polyphenol oxidase (PPO). The obtained biocatalyst TC-PPO showed pH optimum at 7.0–8.0 and temperature optimum at 25 °C. Immobilized PPO shows almost 100% of activity at 0 °C. TC-PPO was more resistant to the denaturation induced by sodium dodecyl sulphate (SDS) detergent as compared to its soluble counterpart and was even slightly activated at SDS concentration of 1%. TC-PPO was tested in the batch reactor for 4-chlorophenol and 4-bromophenol removal. More than 90% removal was achieved for both halogenophenols at concentration of 100 mg/L from aqueous solution. For both halogenophenols TC-PPO works with over 90% removal during first three cycles which decrease to 60% removal efficiency after six cycles each of 8 h duration.

  9. Tentacle carrier for immobilization of potato phenoloxidase and its application for halogenophenols removal from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Loncar, Nikola, E-mail: nloncar@chem.bg.ac.rs [Faculty of Chemistry, University of Belgrade, Studentski trg 12-16, Belgrade (Serbia); Vujcic, Zoran, E-mail: zvujcic@chem.bg.ac.rs [Faculty of Chemistry, University of Belgrade, Studentski trg 12-16, Belgrade (Serbia)

    2011-11-30

    Highlights: Black-Right-Pointing-Pointer We synthesized novel immobilization carrier from reused DEAE-cellulose. Black-Right-Pointing-Pointer We used it for immobilization of PPO through coordinative bonding with copper ions. Black-Right-Pointing-Pointer Immobilized PPO showed better characteristics than soluble PPO. Black-Right-Pointing-Pointer TC-PPO removed over 90% of halogenophenols at concentration of 100 mg/L. - Abstract: Halogenated compounds represent one of the most dangerous environmental pollutants, due to their widespread usage as biocides, fungicides, disinfectants, solvent and other industrial chemicals. Immobilization of a protein through coordinate bonds formed with divalent metal ions is becoming an attractive method due to its reversible nature, since the protein may be easily removed from the support matrix through interruption of the protein-metal bond hence giving inherently cleaner and cheaper technology for wastewater treatment. We have synthesized novel 'tentacle' carrier (TC) and used it for immobilization of partially purified potato polyphenol oxidase (PPO). The obtained biocatalyst TC-PPO showed pH optimum at 7.0-8.0 and temperature optimum at 25 Degree-Sign C. Immobilized PPO shows almost 100% of activity at 0 Degree-Sign C. TC-PPO was more resistant to the denaturation induced by sodium dodecyl sulphate (SDS) detergent as compared to its soluble counterpart and was even slightly activated at SDS concentration of 1%. TC-PPO was tested in the batch reactor for 4-chlorophenol and 4-bromophenol removal. More than 90% removal was achieved for both halogenophenols at concentration of 100 mg/L from aqueous solution. For both halogenophenols TC-PPO works with over 90% removal during first three cycles which decrease to 60% removal efficiency after six cycles each of 8 h duration.

  10. Poorly crystalline hydroxyapatite: A novel adsorbent for enhanced fulvic acid removal from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Wei, Wei [Department of Environmental Science and Engineering, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Center for Collaborative Innovation in Geographical Information Resource Development and Application, Nanjing Normal University, Nanjing 210023 (China); Yang, Lei; Zhong, Wenhui; Cui, Jing [Department of Environmental Science and Engineering, Nanjing Normal University, Nanjing 210023 (China); Wei, Zhenggui, E-mail: weizhenggui@gmail.com [Department of Environmental Science and Engineering, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Center for Collaborative Innovation in Geographical Information Resource Development and Application, Nanjing Normal University, Nanjing 210023 (China)

    2015-03-30

    Graphical abstract: - Highlights: • Poorly crystalline HAP was firstly used for FA removal from aqueous solution. • The maximum adsorption capacity was determined to be 90.20 mg/g at 318 K. • Adsorption kinetics, isotherms and thermodynamic have been studied in detail. • Adsorption mechanism involved surface complexation, electrostatic interaction and hydrogen bonding. - Abstract: In this study, poorly crystalline hydroxyapatite (HAP) was developed as an efficient adsorbent for the removal of fulvic acid (FA) from aqueous solution. Surface functionality, crystallinity, and morphology of the synthetic adsorbent were studied by Fourier-transformation infrared (FT-IR) spectroscopy, powder X-ray diffraction (XRD) and transmission electron microscopy (TEM). The effects of various parameters such as crystallinity of adsorbent, contact time, adsorbent dosage, pH, initial adsorbate concentration, temperature, ionic strength and the presence of alkaline earth metal ions on FA adsorption were investigated. Results indicated that the nanosized HAP calcined at lower temperature was poorly crystalline (X{sub c} = 0.23) and had better adsorption capacity for FA than those (X{sub c} = 0.52, 0.86) calcined at higher temperature. FA removal was increased with increases of adsorbent dosage, temperature, ionic strength and the presence of alkali earth metal ions, but decreased as the pH increased. Kinetic studies showed that pseudo-second-order kinetic model better described the adsorption process. Equilibrium data were best described by Sips models, and the estimated maximum adsorption capacity of poorly crystalline HAP was 90.20 mg/g at 318 K, displaying higher efficiency for FA removal than previously reported adsorbents. FT-IR results revealed that FA adsorption over the adsorbent could be attributed to the surface complexation between the oxygen atom of functional groups of FA and calcium ions of HAP. Regeneration studies indicated that HAP could be recyclable for a long

  11. Removal of heavy metals from aqueous solution by using mango ...

    African Journals Online (AJOL)

    user

    2011-03-14

    Mar 14, 2011 ... exchange, reverse osmosis and solvent extraction (Rich and Cherry, 1987). ... the solution chemistry of the metals, the activity of the functional groups in the .... and Zn2+ from synthetic solutions in single and binary metal solutions. ... coefficient of determination are 0.9449 and 0.9643 for. Langmiur and ...

  12. Solution for Improve the Efficiency of Solar Photovoltaic Installation

    OpenAIRE

    Petru Chioncel; Cristian Paul Chioncel; Nicoleta Gillich

    2013-01-01

    This paper present a solution for improving efficiency of solar photovoltaic installation, realized with fixed solar photovoltaic modules, placed in solar parks or individual installations. The proposed solution to increase the radiation on the solar photovoltaic panels is to use some thin plates covered with a reflective blanket, mounted in front of the solar photovoltaic modules, with the possibility of their adjustment.

  13. Robust and efficient solution procedures for association models

    DEFF Research Database (Denmark)

    Michelsen, Michael Locht

    2006-01-01

    Equations of state that incorporate the Wertheim association expression are more difficult to apply than conventional pressure explicit equations, because the association term is implicit and requires solution for an internal set of composition variables. In this work, we analyze the convergence...... behavior of different solution methods and demonstrate how a simple and efficient, yet globally convergent, procedure for the solution of the equation of state can be formulated....

  14. REMOVAL OF LEAD(II) IONS FROM AQUEOUS SOLUTIONS ...

    African Journals Online (AJOL)

    Preferred Customer

    lung cancer, convulsion and even death if ingested at elevated levels. ... osmosis have been used for removing heavy metal ions from aqueous media [4-6]. ... organic molecules and silica surface functions, (ii) chlorination of the silica surface ...

  15. Adsorptive removal of cationic dye from aqueous solution using ...

    African Journals Online (AJOL)

    PROF HORSFALL

    Received 15 October 2017, received in revised form 03 December 2017, accepted 31 December 2017. Keywords: African Border Tree, ... to remove dyes include flocculation, oxidation, ..... estuarine algae, crustaceans and fishes. Environ.

  16. Removal of chromium and nickel ions from aqueous solution by ...

    African Journals Online (AJOL)

    EJIRO

    mobile in soil and aquatic system and is a strong oxidant capable of being ... effective adsorbents for treatment of metal contaminated ... waste tea, coconut shell and dry plants on the removal of ... which is a waste material from coconut.

  17. An efficient and fair solution for communication graph games

    NARCIS (Netherlands)

    van den Brink, René; Khmelnitskaya, Anna Borisovna; van der Laan, Gerard

    We introduce an efficient solution for games with communication graph structures and show that it is characterized by efficiency, fairness and a new axiom called component balancedness. This latter axiom compares for every component in the communication graph the total payo to the players of this

  18. An efficient algorithm for removal of inactive blocks in reservoir simulation

    Energy Technology Data Exchange (ETDEWEB)

    Abou-Kassem, J.H.; Ertekin, T. (Pennsylvania State Univ., PA (United States))

    1992-02-01

    In the efficient simulation of reservoirs having irregular boundaries one is confronted with two problems: the removal of inactive blocks at the matrix level and the development and application of a variable band-width solver. A simple algorithm is presented that provides effective solutions to these two problems. The algorithm is demonstrated for both the natural ordering and D4 ordering schemes. It can be easily incorporated in existing simulators and results in significant savings in CPU and matrix storage requirements. The removal of the inactive blocks at the matrix level plays a major role in effecting these savings whereas the application of a variable band-width solver plays an enhancing role only. The value of this algorithm lies in the fact that it takes advantage of irregular reservoir boundaries that are invariably encountered in almost all practical applications of reservoir simulation. 11 refs., 3 figs., 3 tabs.

  19. Removal Efficiency of Microbial Contaminants from Hospital Wastewaters

    KAUST Repository

    Timraz, Kenda

    2016-02-01

    This study aims to evaluate the removal efficiency of microbial contaminants from two hospitals on-site Wastewater Treatment Plants (WWTPs) in Saudi Arabia. Hospital wastewaters often go untreated in Saudi Arabia as in many devolving countries, where no specific regulations are imposed regarding hospital wastewater treatment. The current guidelines are placed to ensure a safe treated wastewater quality, however, they do not regulate for pathogenic bacteria and emerging contaminants. Results from this study have detected pathogenic bacterial genera and antibiotic resistant bacteria in the sampled hospitals wastewater. And although the treatment process of one of the hospitals was able to meet current quality guidelines, the other hospital treatment process failed to meet these guidelines and disgorge of its wastewater might be cause for concern. In order to estimate the risk to the public health and the impact of discharging the treated effluent to the public sewage, a comprehensive investigation is needed that will facilitate and guide suggestions for more detailed guidelines and monitoring.

  20. Simultaneous pollutant removal and electricity generation in denitrifying microbial fuel cell with boric acid-borate buffer solution.

    Science.gov (United States)

    Chen, Gang; Zhang, Shaohui; Li, Meng; Wei, Yan

    2015-01-01

    A double-chamber denitrifying microbial fuel cell (MFC), using boric acid-borate buffer solution as an alternative to phosphate buffer solution, was set up to investigate the influence of buffer solution concentration, temperature and external resistance on electricity generation and pollutant removal efficiency. The result revealed that the denitrifying MFC with boric acid-borate buffer solution was successfully started up in 51 days, with a stable cell voltage of 205.1 ± 1.96 mV at an external resistance of 50 Ω. Higher concentration of buffer solution favored nitrogen removal and electricity generation. The maximum power density of 8.27 W/m(3) net cathodic chamber was obtained at a buffer solution concentration of 100 mmol/L. An increase in temperature benefitted electricity generation and nitrogen removal. A suitable temperature for this denitrifying MFC was suggested to be 25 °C. Decreasing the external resistance favored nitrogen removal and organic matter consumption by exoelectrogens.

  1. Dye and its removal from aqueous solution by adsorption: a review.

    Science.gov (United States)

    Yagub, Mustafa T; Sen, Tushar Kanti; Afroze, Sharmeen; Ang, H M

    2014-07-01

    In this review article the authors presented up to-date development on the application of adsorption in the removal of dyes from aqueous solution. This review article provides extensive literature information about dyes, its classification and toxicity, various treatment methods, and dye adsorption characteristics by various adsorbents. One of the objectives of this review article is to organise the scattered available information on various aspects on a wide range of potentially effective adsorbents in the removal of dyes. Therefore, an extensive list of various adsorbents such as natural materials, waste materials from industry, agricultural by-products, and biomass based activated carbon in the removal of various dyes has been compiled here. Dye bearing waste treatment by adsorption using low cost alternative adsorbent is a demanding area as it has double benefits i.e. water treatment and waste management. Further, activated carbon from biomass has the advantage of offering an effected low cost replacement for non-renewable coal based granular activated carbon provided that they have similar or better adsorption on efficiency. The effectiveness of various adsorbents under different physico-chemical process parameters and their comparative adsorption capacity towards dye adsorption has also been presented. This review paper also includes the affective adsorption factors of dye such as solution pH, initial dye concentration, adsorbent dosage, and temperature. The applicability of various adsorption kinetic models and isotherm models for dye removal by wide range of adsorbents is also reported here. Conclusions have been drawn from the literature reviewed and few suggestions for future research are proposed. Copyright © 2014 Elsevier B.V. All rights reserved.

  2. Effect of adsorbents and chemical treatments on the removal of strontium from aqueous solutions

    International Nuclear Information System (INIS)

    Ahmadpour, A.; Zabihi, M.; Tahmasbi, M.; Bastami, T. Rohani

    2010-01-01

    In the present investigation, three different solid wastes namely almond green hull, eggplant hull, and moss were initially treated and used as adsorbents for the adsorption of strontium ion from aqueous solutions. Adsorbent types and chemical treatments are proved to have effective roles on the adsorption of Sr(II) ion. Among the three adsorbents, almond green hull demonstrated strong affinity toward strontium ion in different solutions. The effectiveness of this new adsorbent was studied in batch adsorption mode under a variety of experimental conditions such as: different chemical treatments, various amounts of adsorbent, and initial metal-ion concentration. The optimum doses of adsorbent for the maximum Sr(II) adsorption were found to be 0.2 and 0.3 g for 45 and 102 mg L -1 solutions, respectively. High Sr(II) adsorption efficiencies were achieved only in the first 3 min of adsorbent's contact time. The kinetics of Sr(II) adsorption on almond green hull was also examined and it was observed that it follows the pseudo second-order behavior. Both Langmuir and Freundlich models well predicted the experimental adsorption isotherm data. The maximum adsorption capacity on almond green hull was found to be 116.3 mg g -1 . The present study also confirmed that these low cost agriculture byproducts could be used as efficient adsorbents for the removal of strontium from wastewater streams.

  3. Removal efficiency of methylene blue using activated carbon from waste banana stem: Study on pH influence

    Science.gov (United States)

    Misran, E.; Bani, O.; Situmeang, E. M.; Purba, A. S.

    2018-02-01

    The effort to remove methylene blue in artificial solution had been conducted using adsorption process. The abundant banana stem waste was utilized as activated carbon precursor. This study aimed to analyse the influence of solution pH to removal efficiency of methylene blue using activated carbon from banana stem as adsorbent. Activated carbon from banana stem was obtained by chemical activation using H3PO4 solution. Proximate analysis result showed that the activated carbon has 47.22% of fixed carbon. This value exhibited that banana stem was a potential adsorbent precursor. Methylene blue solutions were prepared at initial concentration of 50 ppm. The influence of solution pH was investigated with the use of 0.2 g adsorbent for 100 mL dye solution. The adsorption was conducted using shaker with at a constant rate of 100 rpm at room temperature for 90 minutes. The results showed that solution pH influenced the adsorption. The activated carbon from banana stem demonstrated satisfying performance since removal efficiencies of methylene blue were higher than 99%.

  4. FACTORS AFFECTING THE REMOVAL OF A BASIC AND AN AZO DYE FROM ARTIFICIAL SOLUTIONS BY ADSORPTION USING ACTIVATED CARBON

    Directory of Open Access Journals (Sweden)

    H Albroomi

    2014-10-01

    Full Text Available Decolourisation of wastewater, particularly from textile industries, is one of the major environmental concerns these days. Current methods for removing dyes from wastewater are costly and cannot effectively be used to treat wide range of such wastewater. This work describes the use of commercial available granular activated carbon (GAC as an efficient adsorbent material for dyes removal. Aqueous solutions of various basic dye Methylene Blue (MB and azo-dye Tartrazine with concentrations 5-20 mg l–1 and 10-100 mg l–1, respectively, were shaken with certain amount of GAC to determine the adsorption capacity and removal efficiencies. The effects of adsorbent dose, initial pH, initial dye concentration, agitation speed and contact time on dyes removal efficiencies have been studied. Maximum dye concentration was removed from the solution within 60-90 min after the beginning of every experiment. Adsorption parameters were found to fit well into Langmuir and Freundlich adsorption isotherms models with correlation coefficient (R2 > 0.99 in the concentration range of MB and TZ studied.

  5. Nanotubular Halloysite Clay as Efficient Water Filtration System for Removal of Cationic and Anionic Dyes

    International Nuclear Information System (INIS)

    Zhao, Yafei; Abdullayev, Elshad; Lvov, Yuri

    2014-01-01

    Halloysite nanotubes, chemically similar to kaolinite, are formed by rolling of kaolinite layers in tubes with diameter of 50 nm and length of ca. 1 μm. Halloysite has negative SiO 2 outermost and positive Al 2 O 3 inner lumen surface, which enables it to be used as potential absorbent for both cationic and anionic dyes due to the efficient bivalent adsorbancy. An adsorption study using cationic Rhodamine 6G and anionic Chrome azurol S has shown approximately two times better dye removal for halloysite as compared to kaolinite. Halloysite filters have been effectively regenerated up to 50 times by burning the adsorbed dyes. Overall removal efficiency of anionic Chrome azurol S exceeded 99.9% for 5th regeneration cycle of halloysite. Chrome azurol S adsorption capacity decreases with the increase of ionic strength, temperature and pH. For cationic Rhodamine 6G, higher ionic strength, temperature and initial solution concentration were favorable to enhanced adsorption with optimal pH 8. These results indicate a potential to utilize halloysite for the removal of ionic dyes from environmental waters

  6. Chitin/clay microspheres with hierarchical architecture for highly efficient removal of organic dyes.

    Science.gov (United States)

    Xu, Rui; Mao, Jie; Peng, Na; Luo, Xiaogang; Chang, Chunyu

    2018-05-15

    Numerous adsorbents have been reported for efficient removal of dye from water, but the high cost raw materials and complicated fabrication process limit their practical applications. Herein, novel nanocomposite microspheres were fabricated from chitin and clay by a simple thermally induced sol-gel transition. Clay nanosheets were uniformly embedded in a nanofiber weaved chitin microsphere matrix, leading to their hierarchical architecture. Benefiting from this unique structure, microspheres could efficiently remove methylene blue (MB) through a spontaneous physic-sorption process which fit well with pseudo-second-order and Langmuir isotherm models. The maximal values of adsorption capability obtained by calculation and experiment were 152.2 and 156.7 mg g -1 , respectively. Chitin/clay microspheres (CCM2) could remove 99.99% MB from its aqueous solution (10 mg g -1 ) within 20 min. These findings provide insight into a new strategy for fabrication of dye adsorbents with hierarchical structure from low cost raw materials. Copyright © 2018 Elsevier Ltd. All rights reserved.

  7. Removal of Uranium from Aqueous Solutions using Ammonium ...

    African Journals Online (AJOL)

    NICOLAAS

    content was determined by Inductively Coupled Plasma Optical Emission Specroscopy (ICP-OES). The removal of uranium ... systems and may influence the surface properties of such adsorbents. .... The high silica content of the natural zeolite makes it more ..... average drop of 24.94 %) due to competition for binding sites.

  8. Fluoride removal from aqueous solution by pumice: case study on ...

    African Journals Online (AJOL)

    The fluoride removal from synthetic water by pumice was studied at batch experiments in this study. The effect of pH, contact time, fluoride concentration and adsorbent dose on the fluoride sequestration was investigated. The optimum conditions were studied on Kuhbonan water as a case study. The results showed that ...

  9. Removal of lead (II) from aqueous solutions using rice straw.

    Science.gov (United States)

    Amer, Hayam; El-Gendy, Ahmed; El-Haggar, Salah

    2017-09-01

    Lead (Pb 2+ ) is a heavy metal which is utilized in several industries and can have severe impact on the environment and human health. Research work has been carried out lately on the feasibility of using various low cost materials in the removal of heavy metals from wastewater. In this study, the feasibility of utilizing raw rice straw for removal of Pb 2+ from water through biosorption was investigated using batch equilibrium experiments. The effect of several operating parameters on the removal of Pb 2+ using rice straw was studied, revealing the optimum parameters at an initial Pb 2+ concentration of 40 mg/l were: 30 min contact time at a pH of 5.5, particle size 75-150 μm and a dose of 4 g/l. A maximum removal of 94% was achieved under optimum conditions. Langmuir and Freundlich isotherm models were used for the evaluation of the equilibrium experimental data. The maximum adsorption capacity of rice straw calculated using the Langmuir isotherm was 42.55 mg/g.

  10. Removal of 4-Chlorophenol from Aqueous Solutions Using Graphene Oxide Nanoporous Adsorbent

    Directory of Open Access Journals (Sweden)

    akbar eslami

    2015-03-01

    Full Text Available In this study, graphene oxide was used as a nanostructured adsorbent with properties supposedly better than other common adsorbents to remove 4-chlorophenol from aqueous solutions. For this purpose, graphene oxide was initially synthesized using the Hummer's method and x-ray diffraction and scanning electron microscopy were employed to identify its morphology and structure. The variables involved in the absorption process (including 4-chlorophenol initial concentration, adsorbent dosage, and pH were investigated based on the one-factor-at-a-time method. Eventually, the data were confirmed against the Langmuir and Freundlich isotherms. It was found that the adsorption process reached equilibrium in 20 minutes. A dosage of 0.4 g/L graphene oxide at pH=8 brought about 90% removal of 10 mg/L 4-chlorophenol within 5 minutes. The adsorption isotherm was described well by the Langmuir isotherm model and the values for R2 and RL were recorded as 0.99 for and 0.34, respectively. Being a low cost and highly efficient process, the adsorption process using graphene oxide adsorbent may be recommended for the reduction and elimination of pollutants in the environment, especially those in aqueous solutions.

  11. Parallel artificial liquid membrane extraction as an efficient tool for removal of phospholipids from human plasma.

    Science.gov (United States)

    Ask, Kristine Skoglund; Bardakci, Turgay; Parmer, Marthe Petrine; Halvorsen, Trine Grønhaug; Øiestad, Elisabeth Leere; Pedersen-Bjergaard, Stig; Gjelstad, Astrid

    2016-09-10

    Generic Parallel Artificial Liquid Membrane Extraction (PALME) methods for non-polar basic and non-polar acidic drugs from human plasma were investigated with respect to phospholipid removal. In both cases, extractions in 96-well format were performed from plasma (125μL), through 4μL organic solvent used as supported liquid membranes (SLMs), and into 50μL aqueous acceptor solutions. The acceptor solutions were subsequently analysed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) using in-source fragmentation and monitoring the m/z 184→184 transition for investigation of phosphatidylcholines (PC), sphingomyelins (SM), and lysophosphatidylcholines (Lyso-PC). In both generic methods, no phospholipids were detected in the acceptor solutions. Thus, PALME appeared to be highly efficient for phospholipid removal. To further support this, qualitative (post-column infusion) and quantitative matrix effects were investigated with fluoxetine, fluvoxamine, and quetiapine as model analytes. No signs of matrix effects were observed. Finally, PALME was evaluated for the aforementioned drug substances, and data were in accordance with European Medicines Agency (EMA) guidelines. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. γ-radiation induced tetracycline removal in an aqueous solution

    International Nuclear Information System (INIS)

    Zhou Fei; Guo Zhaobing; Zhang Chaozhi; Lin Mingyue; Wu Menglong; Zhao Yongfu

    2012-01-01

    Degradation effect of tetracycline (TC) by γ-radiation was investigated in an aqueous solution. The effects of initial concentrations of TC, pH values, combining with H 2 O 2 or CH 3 OH on degradation of TC were studied. Results showed that TC can be effectively degradated by γ-irradiation in an aqueous solution. Degradation of TC could be remarkably improved both in acid solution and alkaline solution, especially when pH value was 9.0. In addition, H 2 O 2 could gently promote degradation of TC induced by γ-radiation. While, CH 3 OH markedly restrained degradation of TC induced by γ-radiation. The degradation mechanism of TC was supposed by results of quantum chemical calculations and LC-MS. Results proved that degradation of TC induced by γ-radiation was mainly ascribed to · OH oxidation. (authors)

  13. Removal of nitrate from aqueous solution using cetylpyridinium bromide (CPB) modified zeolite as adsorbent

    International Nuclear Information System (INIS)

    Zhan Yanhui; Lin Jianwei; Zhu Zhiliang

    2011-01-01

    Surfactant modified zeolites (SMZ) with different coverage types were prepared by loading the cetylpyridinium bromide (CPB) onto the surface of the natural zeolites. The adsorption behavior of nitrate on SMZ was investigated. Natural zeolite and SMZ with monolayer CPB coverage were inefficient for the removal of nitrate from aqueous solution. However, SMZ with patchy bilayer or bilayer CPB coverage was efficient in nitrate removal, and the nitrate adsorption capacity of SMZ increased with its CPB loading. For typical SMZ with bilayer CPB coverage, the nitrate adsorption process was well described by the pseudo-second-order kinetic model, and the experimental isotherm data fitted well with the Langmuir, Freundlich and Dubinin-Redushkevich isotherm models. Thermodynamic parameters such as Gibbs free energy change, enthalpy change and entropy change were calculated and the results showed that the adsorption of nitrate on SMZ was spontaneous and exothermic in nature. The presence of competing anions such as chloride, sulfate and bicarbonate ions slightly reduced the nitrate adsorption efficiency. Anionic exchange and electrostatic interaction were proven to be the main mechanisms that govern the adsorption of nitrate on SMZ.

  14. Chromium (Ⅵ) removal from aqueous solutions through powdered activated carbon countercurrent two-stage adsorption.

    Science.gov (United States)

    Wang, Wenqiang

    2018-01-01

    To exploit the adsorption capacity of commercial powdered activated carbon (PAC) and to improve the efficiency of Cr(VI) removal from aqueous solutions, the adsorption of Cr(VI) by commercial PAC and the countercurrent two-stage adsorption (CTA) process was investigated. Different adsorption kinetics models and isotherms were compared, and the pseudo-second-order model and the Langmuir and Freundlich models fit the experimental data well. The Cr(VI) removal efficiency was >80% and was improved by 37% through the CTA process compared with the conventional single-stage adsorption process when the initial Cr(VI) concentration was 50 mg/L with a PAC dose of 1.250 g/L and a pH of 3. A calculation method for calculating the effluent Cr(VI) concentration and the PAC dose was developed for the CTA process, and the validity of the method was confirmed by a deviation of <5%. Copyright © 2017. Published by Elsevier Ltd.

  15. Adsorption Study of Electric Arc Furnace Slag for the Removal of Manganese from Solution

    OpenAIRE

    C. L. Beh; Luqman Chuah; Thomas S.Y. Choong; Mohd. Z.B. Kamarudzaman; Khalina Abdan

    2010-01-01

    Problem statement: Steel making slag from Electric Arc Furnace (EAF) is an abundant by-product in Malaysia steel making industry. It has potential to be used for heavy metal removal from contaminated water or waste water. Approach: The aim of this study was to investigate the characteristic and behavior of manganese removal by using EAF slag for efficient metal removal. The removal characteristics of manganese were investigated in term of sorption kinetics and isotherm. The batch adsorption k...

  16. Solution for Improve the Efficiency of Solar Photovoltaic Installation

    Directory of Open Access Journals (Sweden)

    Petru Chioncel

    2013-01-01

    Full Text Available This paper present a solution for improving efficiency of solar photovoltaic installation, realized with fixed solar photovoltaic modules, placed in solar parks or individual installations. The proposed solution to increase the radiation on the solar photovoltaic panels is to use some thin plates covered with a reflective blanket, mounted in front of the solar photovoltaic modules, with the possibility of their adjustment.

  17. Efficient solution of a multi objective fuzzy transportation problem

    Science.gov (United States)

    Vidhya, V.; Ganesan, K.

    2018-04-01

    In this paper we present a methodology for the solution of multi-objective fuzzy transportation problem when all the cost and time coefficients are trapezoidal fuzzy numbers and the supply and demand are crisp numbers. Using a new fuzzy arithmetic on parametric form of trapezoidal fuzzy numbers and a new ranking method all efficient solutions are obtained. The proposed method is illustrated with an example.

  18. Removal of thorium(IV) from aqueous solutions by natural sepiolite

    Energy Technology Data Exchange (ETDEWEB)

    Erden, Kadriye Esen [Pamukkale Univ., Denizli (Turkey). Dept. of Electricity and Energy; Donat, Ramazan [Pamukkale Univ., Denizli (Turkey). Dept. of Chemistry

    2017-06-01

    Natural sepiolite has been tested as a potential sorbent for the removal of Th(IV) from aqueous solutions by batch technique. Effects of various parameters on the adsorption process have been investigated. Under optimum conditions, Th(IV) was adsorbed with high adsorption efficiency. The results indicated that sorption of Th(IV) on sepiolite was strongly affected by pH values and temperature. The adsorption patterns of thorium on the sepiolite adsorbent followed the Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherms. The thermodynamic data (ΔH , ΔS , ΔG ) are calculated from the temperature-dependent sorption isotherms. The results suggest that sorption process of Th(IV) on sepiolite is spontaneous and endothermic.

  19. Final Scientific Report - Wireless and Sensing Solutions Advancing Industrial Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Budampati, Rama; McBrady, Adam; Nusseibeh, Fouad

    2009-09-28

    The project team's goal for the Wireless and Sensing Solution Advancing Industrial Efficiency award (DE-FC36-04GO14002) was to develop, demonstrate, and test a number of leading edge technologies that could enable the emergence of wireless sensor and sampling systems for the industrial market space. This effort combined initiatives in advanced sensor development, configurable sampling and deployment platforms, and robust wireless communications to address critical obstacles in enabling enhanced industrial efficiency.

  20. Antibiotic resistance genes fate and removal by a technological treatment solution for water reuse in agriculture.

    Science.gov (United States)

    Luprano, Maria Laura; De Sanctis, Marco; Del Moro, Guido; Di Iaconi, Claudio; Lopez, Antonio; Levantesi, Caterina

    2016-11-15

    In order to mitigate the potential effects on the human health which are associated to the use of treated wastewater in agriculture, antibiotic resistance genes (ARGs) are required to be carefully monitored in wastewater reuse processes and their spread should be prevented by the development of efficient treatment technologies. Objective of this study was the assessment of ARGs reduction efficiencies of a novel technological treatment solution for agricultural reuse of municipal wastewaters. The proposed solution comprises an advanced biological treatment (Sequencing Batch Biofilter Granular Reactor, SBBGR), analysed both al laboratory and pilot scale, followed by sand filtration and two different disinfection final stages: ultraviolet light (UV) radiation and peracetic acid (PAA) treatments. By Polymerase Chain Reaction (PCR), the presence of 9 ARGs (ampC, mecA, ermB, sul1, sul2, tetA, tetO, tetW, vanA) were analysed and by quantitative PCR (qPCR) their removal was determined. The obtained results were compared to the reduction of total bacteria (16S rDNA gene) and of a faecal contamination indicator (Escherichia coli uidA gene). Only four of the analysed genes (ermB, sul1, sul2, tetA) were detected in raw wastewater and their abundance was estimated to be 3.4±0.7 x10(4) - 9.6±0.5 x10(9) and 1.0±0.3 x10(3) to 3.0±0.1 x10(7) gene copies/mL in raw and treated wastewaters, respectively. The results show that SBBGR technology is promising for the reduction of ARGs, achieving stable removal performance ranging from 1.0±0.4 to 2.8±0.7 log units, which is comparable to or higher than that reported for conventional activated sludge treatments. No reduction of the ARGs amount normalized to the total bacteria content (16S rDNA), was instead obtained, indicating that these genes are removed together with total bacteria and not specifically eliminated. Enhanced ARGs removal was obtained by sand filtration, while no reduction was achieved by both UV and PAA disinfection

  1. Adsorption behavior of multi-walled carbon nanotubes for the removal of olaquindox from aqueous solutions

    International Nuclear Information System (INIS)

    Zhang, Lei; Xu, Tianci; Liu, Xueyan; Zhang, Yunyu; Jin, Hongjing

    2011-01-01

    Highlights: ► Removal of olaquindox—a hazardous pollutant using MWCNT was investigated. ► A comparative analysis showed MWCNT was highly efficient for the removal of olaquindox. ► Adsorption equilibrium was reached in 2.0 min following pseudo-second-order model. ► Physisorption and inner diffusion are the characteristics of the adsorption system. ► Langmuir adsorption isotherms are adequate for modeling the adsorption process. - Abstract: Multi-walled carbon nanotubes (MWCNT) were employed for the sorption of olaquindox (OLA) from aqueous solution. A detailed study of the adsorption process was performed by varying pH, ionic strength, sorbent amount, sorption time and temperature. The adsorption mechanism is probably the non-electrostatic π–π dispersion interaction and hydrophobic interaction between OLA and MWCNT. The adsorption efficiency could reach 99.7%, suggesting that MWCNT is excellent adsorbents for effective OLA removal from water. OLA adsorption kinetics were found to be very fast and equilibrium was reached within 2.0 min following the pseudo-second-order model with observed rate constants (k) of 0.169–1.048 g mg −1 min −1 (at varied temperatures). The overall rate process appeared to be influenced by both external mass transfer and intraparticle diffusion, but mainly governed by intraparticle diffusion. A rapid initial adsorption behavior occurred within a short period of time in this adsorption system. The sorption data could be well interpreted by the Langmuir model with the maximum adsorption capacity of 133.156 mg g −1 (293 K) of OLA on MWCNT. The mean energy of adsorption was calculated to be 0.124 kJ mol −1 (293 K) from the Dubinin–Radushkevich adsorption isotherm. Moreover, the thermodynamic parameters showed the spontaneous, exothermic and physical nature of the adsorption process.

  2. Adsorptive removal of arsenate from aqueous solutions by biochar supported zero-valent iron nanocomposite: Batch and continuous flow tests

    International Nuclear Information System (INIS)

    Wang, Shengsen; Gao, Bin; Li, Yuncong; Creamer, Anne Elise; He, Feng

    2017-01-01

    Highlights: • Biochar supported nZVI (nZVI/BC) was synthesized. • nZVI/BC showed excellent As(V) removal efficiency in batch and CMR experiments. • 100% removal efficiency was achieved in CMRs. • Surface adsorption was the dominant removal mechanism. - Abstract: Arsenate (As(V)) removal ability by nanoscale zero-valent iron (nZVI) is compromised by aggregation of nZVI particles. In this work, pine derived biochar (PB) was used as a supporting material to stabilize nZVI for As(V) removal. The biochar supported nZVI (nZVI/BC) was synthesized by precipitating the nanoparticles on carbon surfaces. Experiments using batch and continuous flow, completely mixed reactors (CMRs) were carried out to investigate the removal of As(V) by the nZVI/BC from aqueous solutions. Batch experiments showed that nZVI/BC had high As(V) removal capacity in a wide range of pH (3–8). Kinetic data revealed that equilibrium was reached within 1 h and the isotherm data showed that the Langmuir maximum adsorption capacity of the nZVI/BC for As(V) at pH 4.1 was 124.5 g kg −1 . As(V) (100 mg L −1 ) adsorption in anoxic condition was about 8% more than in oxic conditions, where As(V) reduction was observed in anoxic condition. The performance of the nZVI/BC in flowing condition was evaluated in CMRs at influent As(V) concentrations of 2.1 and 5.5 mg L −1 and the adsorbent removed 100% and 90% of the As(V), respectively. Furthermore, the nZVI/BC composite is magnetic which facilitates collection from aqueous solutions.

  3. Adsorptive removal of arsenate from aqueous solutions by biochar supported zero-valent iron nanocomposite: Batch and continuous flow tests

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shengsen [Department of Agricultural and Biological Engineering, University of Florida, Gainesville, FL 32611 (United States); Gao, Bin, E-mail: bg55@ufl.edu [Department of Agricultural and Biological Engineering, University of Florida, Gainesville, FL 32611 (United States); Li, Yuncong [Tropical Research and Education Center, University of Florida, Homestead, FL 33031 (United States); Creamer, Anne Elise [Department of Agricultural and Biological Engineering, University of Florida, Gainesville, FL 32611 (United States); He, Feng [College of Biological and Environmental Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310014 (China)

    2017-01-15

    Highlights: • Biochar supported nZVI (nZVI/BC) was synthesized. • nZVI/BC showed excellent As(V) removal efficiency in batch and CMR experiments. • 100% removal efficiency was achieved in CMRs. • Surface adsorption was the dominant removal mechanism. - Abstract: Arsenate (As(V)) removal ability by nanoscale zero-valent iron (nZVI) is compromised by aggregation of nZVI particles. In this work, pine derived biochar (PB) was used as a supporting material to stabilize nZVI for As(V) removal. The biochar supported nZVI (nZVI/BC) was synthesized by precipitating the nanoparticles on carbon surfaces. Experiments using batch and continuous flow, completely mixed reactors (CMRs) were carried out to investigate the removal of As(V) by the nZVI/BC from aqueous solutions. Batch experiments showed that nZVI/BC had high As(V) removal capacity in a wide range of pH (3–8). Kinetic data revealed that equilibrium was reached within 1 h and the isotherm data showed that the Langmuir maximum adsorption capacity of the nZVI/BC for As(V) at pH 4.1 was 124.5 g kg{sup −1}. As(V) (100 mg L{sup −1}) adsorption in anoxic condition was about 8% more than in oxic conditions, where As(V) reduction was observed in anoxic condition. The performance of the nZVI/BC in flowing condition was evaluated in CMRs at influent As(V) concentrations of 2.1 and 5.5 mg L{sup −1} and the adsorbent removed 100% and 90% of the As(V), respectively. Furthermore, the nZVI/BC composite is magnetic which facilitates collection from aqueous solutions.

  4. Removal of cadmium and cyanide from aqueous solutions through electrodialysis

    Directory of Open Access Journals (Sweden)

    Marder Luciano

    2003-01-01

    Full Text Available The discharge of galvanic industry wastewaters containing heavy metals and cyanide is one of the largest sources of water pollution. The use of the electrodialysis technique for the treatment of a synthetic wastewater containing approximately 0.0089 mol L-1 cadmium and 0.081 mol L-1 cyanide was studied using a five-compartment electrodialysis cell. The results demonstrate that the removal of cadmium and cyanide depends on the applied current density and it is limited by the precipitation of cadmium on the cation-exchange membrane in the diluate central cell compartment.

  5. Struvite Precipitation and Phosphorous Removal from Urine Synthetic Solution: Reaction Kinetic Study

    Directory of Open Access Journals (Sweden)

    Marwa Saied Shalaby

    2015-03-01

    Full Text Available Phosphorus, like oil, is a non-renewable resource that must be harvested from finite resources in the earth’s crust. An essential element for life, phosphorus is becoming increasingly scarce, contaminated, and difficult to extract. Struvite or magnesium ammonium phosphate (MgNH4PO4.6H2O is a white, crystalline phosphate mineral that can be used as a bio-available fertilizer. The main objective of this research is to indicate the most important operating parameters affecting struvite precipitation by means of chemical reaction kinetics. The present study explores struvite precipitation by chemical method under different starting molar ratios, pH and SSR. It is shown that an increase of starting Mg: PO4: NH4 with respect to magnesium (1.6:1:1 strongly influences the growth rate of struvite and so the efficiency of the phosphate removal. This was attributed to the effect of magnesium on the struvite solubility product and on the reached supersaturation Super Saturation Ratio at optimum starting molar ratio and pH. It was also shown, by using chemical precipitation method that the determined Super Saturation Ratio (SSR values of struvite, at 8, 8.5, 9, 9.5 and 10 are 1.314, 4.29, 8.89, 9.87 and 14.89 respectively are close to those presented in the literature for different origins of wastewater streams. The results show that SSR , pH, and starting molar ratio strongly influences the kinetics of precipitation and so phosphorous removal to reach 93% removal percent , 5.95 mg/lit as a minimum PO4 remained in solution, and 7.9 gm precipitated struvite from feed synthetic solution of 750 ml . The product was subjected to chemical analysis by means of EDIX-FTIR, SEM and XRD showing conformity with published literature. First-order kinetics was found to be sufficient to describe the rate data. The rates increased with increasing pH and so SSR and the apparent rate constants for the reaction were determined. © 2015 BCREC UNDIP. All rights reserved

  6. Predicting the efficiency of deposit removal during filter backwash

    African Journals Online (AJOL)

    Abstract. The long-term performance of granular media filters used in drinking water treatment is ultimately limited by the efficiency ... efficiency) within each set of experiments appeared to affect the efficiency of backwash in addition to the parameters varied ... anisms involved in filter cleaning (Amirtharajah, 1978; Amirth-.

  7. Heating Changes Bio-Schwertmannite Microstructure and Arsenic(III Removal Efficiency

    Directory of Open Access Journals (Sweden)

    Xingxing Qiao

    2017-01-01

    Full Text Available Schwertmannite (Sch is an efficient adsorbent for arsenic(III removal from arsenic(III-contaminated groundwater. In this study, bio-schertmannite was synthesized in the presence of dissolved ferrous ions and Acidithiobacillus ferrooxidans LX5 in a culture media. Bio-synthesized Sch characteristics, such as total organic carbon (TOC, morphology, chemical functional groups, mineral phase, specific surface area, and pore volume were systematically studied after it was dried at 105 °C and then heated at 250–550 °C. Differences in arsenic(III removal efficiency between 105 °C dried-sch and 250–550 °C heated-sch also were investigated. The results showed that total organic carbon content in Sch and Sch weight gradually decreased when temperature increased from 105 °C to 350 °C. Sch partly transformed to another nanocrystalline or amorphous phase above 350 °C. The specific surface area of 250 °C heated-sch was 110.06 m2/g compared to 5.14 m2/g for the 105 °C dried-sch. Total pore volume of 105 °C dried-sch was 0.025 cm3/g with 32.0% mesopore and 68.0% macropore. However, total pore volume of 250 °C heated-mineral was 0.106 cm3/g with 23.6% micropore, 33.0% mesopore, and 43.4% macropore. The arsenic(III removal efficiency from an initial 1 mg/L arsenic(III solution (pH 7.5 was 25.1% when 0.25 g/L of 105 °C dried-sch was used as adsorbent. However, this efficiency increased to 93.0% when using 250 °C heated-sch as adsorbent. Finally, the highest efficiency for arsenic(III removal was obtained with sch-250 °C due to high amounts of sorption sites in agreement with the high specific surface area (SSA obtained for this sample.

  8. REMOVAL OF LEAD(II) IONS FROM AQUEOUS SOLUTIONS ...

    African Journals Online (AJOL)

    a

    The adsorption followed the first order kinetics and was found to be pH ... metals from wastewater is with inadequate efficiencies at law metal ..... The thermodynamic quantities ∆H, ∆S, ∆G of Pb(II) adsorption on activated carbon were.

  9. Uranium removal from organic solutions of PUREX process

    International Nuclear Information System (INIS)

    Dell'Occhio, L.A.; Dupetit, G.A.; Pascale, A.A.; Vicens, H.E.

    1987-01-01

    During the uranium extraction process with tributyl phosphate (TBP) in nitric medium, a bi solvated, non hydrated complex is formed, of formula UO2(NO3)2TBP, which is soluble in the diluent, a paraffin hydrocarbon. As it is known that some uranium salts, for instance the nitrate, when dissolved in organic solvents, like isopropanol, can be discharged as complex molecules at the cathode of an electrodeposition cell, it was decided to apply this technique to uranium loaded TBP solutions. From preliminary experiments resulted a practical possibility for the analytical control through the alpha measurement of electro deposits. This technique could be applied as well to the treatment of depleted organic streams carrying undesirable alpha activity, because the so treated solutions become deprived of uranium. This work presents the curves obtained working at constant voltage with uranium-loaded TBP solutions, the determination of the optimal operation voltage in these conditions, the electrodeposition yield for electro polished copper and stainless steel cathodes and the tests of reproducibility of deposits. A summary of the results obtained operating the high voltage supply at constant power is also presented. (Author)

  10. Potential use of maize waste for the removal of Pb(II) from aqueous solution

    CSIR Research Space (South Africa)

    Okonkwo, J

    2006-09-01

    Full Text Available batch adsorption procedures. The utilization of tassels for the removal of toxic heavy metals from effluent solutions would, however, attach some economic value to this waste material. Tassel flowers were collected just prior to harvest, dried under...

  11. Efficiency of Osmotic Dehydration of Apples in Polyols Solutions

    Directory of Open Access Journals (Sweden)

    Joanna Cichowska

    2018-02-01

    Full Text Available The present study aimed to evaluate the influence of selected compounds from the polyol group, as well as other saccharides, on the osmotic dehydration process of apples. The following alternative solutions were examined: erythritol, xylitol, maltitol, inulin and oligofructose. Efficiency of the osmotic dehydration process was evaluated based on the kinetics of the process, and through comparison of the results obtained during the application of a sucrose solution. This innovative research utilizes alternative solutions in osmotic pretreatment, which until now, have not been commonly used in fruit processing by researchers worldwide. Results indicate that erythritol and xylitol show stronger or similar efficiency to sucrose; however, the use of inulin, as well as oligofructose, was not satisfactory due to the insufficient, small osmotic driving forces of the process, and the low values of mass transfer parameters.

  12. Efficiency of Osmotic Dehydration of Apples in Polyols Solutions.

    Science.gov (United States)

    Cichowska, Joanna; Żubernik, Joanna; Czyżewski, Jakub; Kowalska, Hanna; Witrowa-Rajchert, Dorota

    2018-02-17

    The present study aimed to evaluate the influence of selected compounds from the polyol group, as well as other saccharides, on the osmotic dehydration process of apples. The following alternative solutions were examined: erythritol, xylitol, maltitol, inulin and oligofructose. Efficiency of the osmotic dehydration process was evaluated based on the kinetics of the process, and through comparison of the results obtained during the application of a sucrose solution. This innovative research utilizes alternative solutions in osmotic pretreatment, which until now, have not been commonly used in fruit processing by researchers worldwide. Results indicate that erythritol and xylitol show stronger or similar efficiency to sucrose; however, the use of inulin, as well as oligofructose, was not satisfactory due to the insufficient, small osmotic driving forces of the process, and the low values of mass transfer parameters.

  13. Investigation on the efficiency of treated Palm Tree waste for removal of organic pollutants

    Science.gov (United States)

    Azoulay, Karima; El HajjajiI, Souad; Dahchour, Abdelmalek

    2017-04-01

    Development of the industrial sector generates several problems of environmental pollution. This issue rises concern among scientific community and decision makers, in this work; we e interested in water resources polluted by the chemical substances, which can cause various problems of health. As an example, dyes generated by different industrial activities such as textile, cosmetic, metal plating, leather, paper and plastic sectors, constitute an important source of pollution. In this work, we aim at investigating the efficiency of palm tree waste for removal of dyes from polluted solution. Our work presents a double environmental aspect, on one hand it constitutes an attempt for valorization of Palm Tree waste, and on the other hand it provides natural adsorbent. The study focuses on the effectiveness of the waste in removing Methylene Bleu and Methyl Orange taken as models of pollutants from aqueous solution. Kinetics and isotherm experiments were conducted in order to determine the sorption behavior of the examined dye. The effects of initial dye and adsorbent concentrations are considered. The results indicate that the correlation coefficient calculated from pseudo-second order equation was higher than the other kinetic equations, indicating that equilibrium data fitted well with pseudo-second order model where adsorption process was chemisorption. The adsorption equilibrium was well described by Langmuir isotherm model.

  14. Preparation of magnetic MIL-101 (Cr) for efficient removal of ciprofloxacin.

    Science.gov (United States)

    Bayazit, Şahika Sena; Danalıoğlu, Selen Tuğba; Abdel Salam, Mohamed; Kerkez Kuyumcu, Özge

    2017-11-01

    Metal organic frameworks are widely used as adsorbent materials in recent years. In this study, the most prepared metal organic framework MIL-101 was prepared by hydrothermal method and featured magnetic property using co-precipitation method Fe 3 O 4 . Then, the prepared composite (MIL-101/Fe 3 O 4 ) was first characterized using XRD, FTIR, SEM-EDS, and surface area analysis, then was used for the adsorptive removal of the most used antibiotic, ciprofloxacin (CIP). The effect of different adsorption variables which may affect the removal of CIP by MIL-101/Fe 3 O 4 was investigated, as well as their adsorbent quantity, initial CIP concentration, pH, temperature, and contact time. The non-linear Langmuir and Freundlich isotherm were applied to experimental data. It was observed that rising solution temperature decreases adsorption efficiency, as the maximum adsorption uptake value was 63.28 mg g -1 at 298 K and 22.93 mg g -1 at 313 K, indicating the exothermic nature of the adsorption. The adsorption was studied kinetically and found to follow the pseudo-second-order kinetic model. The desorption of CIP from the MIL-101/Fe 3 O 4 was investigated using three different eluents, and the results showed that phosphate-buffered solution was the most effective desorption eluent. Graphical abstract Schematic diagram of the preparation steps of MIL-101/Fe3O4.

  15. Removable orthodontic appliances: new perspectives on capabilities and efficiency.

    Science.gov (United States)

    Hamid Zafarmand, A; Mahdi Zafarmand, M

    2013-06-01

    Removable appliances are a dependable choice for many patients but like all orthodontic appliances, they have some limitations in use. Patient selection and appropriate appliance design are two key factors for success. Many patients, especially adults, prefer intra-oral appliances to extra-oral devices. Sometimes a removable intra-oral appliance can solve a dental problem in a shorter period of time compared to fixed treatment, and this has also been repeatedly seen in molar distalisation. From the interceptive perspective, the appliance can prevent or alleviate an impending crowding for erupting permanent incisors. This article describes 5 patients with different orthodontic problems: impending crowding for erupting upper canine with 2 approaches, provision of space for upper cuspids, resolution of chronic attrition of anterior teeth, relief of space shortage for upper canines eruption, and reduction of excess overjet. All subjects were treated with removable appliances of various designs.

  16. Removal of copper (II from aqueous solutions by adsorption onto granular activated carbon in the presence of competitor ions

    Directory of Open Access Journals (Sweden)

    Saeed Almohammadi

    2016-04-01

    Full Text Available In this work, the removal of copper from an aqueous solution by granular activated carbon (GAC in the presence of competitor ions was studied. A batch adsorption was carried out and different parameters such as pH, contact time, initial copper concentration and competitor ions concentration were changed to determine the optimum conditions for adsorption. The optimum pH required for maximum adsorption was found to be 4.5 for copper. Equilibrium was evaluated at 144 h at room temperature. The removal efficiency of Cu(II was 71.12% at this time. The kinetics of copper adsorption on activated carbon followed the pseudo second-order model. The experimental equilibrium sorption data were tested using the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich (D-R equations and the Langmuir model was found to be well fitted for copper adsorption onto GAC. The maximum adsorption capacity of the adsorbent for Cu(II was calculated from the Langmuir isotherm and found to be 7.03 mg/g. Subsequently, the removal of copper by granular activated carbon in the presence of Ag1+ and Mn2+ as competitor ions was investigated. The removal efficiency of Cu(II ions without the presence of the competitor ions was 46% at 6 h, while the removal efficiency of Cu(II ions in the presence of competitor ions, Ag1+ and Mn2+ , was 34.76% and 31.73%, respectively.

  17. Removal of copper (II) from aqueous solutions by adsorption onto granular activated carbon in the presence of competitor ions

    International Nuclear Information System (INIS)

    Almohammadi, S.; Mirzaei, M.

    2016-01-01

    In this work, the removal of copper from an aqueous solution by granular activated carbon (GAC) in the presence of competitor ions was studied. A batch adsorption was carried out and different parameters such as p H, contact time, initial copper concentration and competitor ions concentration were changed to determine the optimum conditions for adsorption. The optimum p H required for maximum adsorption was found to be 4.5 for copper. Equilibrium was evaluated at 144 h at room temperature. The removal efficiency of Cu(II) was 71.12% at this time. The kinetics of copper adsorption on activated carbon followed the pseudo second-order model. The experimental equilibrium sorption data were tested using the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich (D-R) equations and the Langmuir model was found to be well fitted for copper adsorption onto GAC. The maximum adsorption capacity of the adsorbent for Cu(II) was calculated from the Langmuir isotherm and found to be 7.03 mg/g. Subsequently, the removal of copper by granular activated carbon in the presence of Ag 1 + and Mn 2 + as competitor ions was investigated. The removal efficiency of Cu(II) ions without the presence of the competitor ions was 46% at 6 h, while the removal efficiency of Cu(II) ions in the presence of competitor ions, Ag 1 + and Mn 2 + , was 34.76% and 31.73%, respectevely.

  18. Eosin Removal Properties of Organo-Local Clay from Aqueous Solution

    OpenAIRE

    Rawan Al-Faze; Fethi Kooli

    2014-01-01

    Local clay from Al-Madinah Al-Munawwarah was modified by a solution of cetyltrimethylammonium bromide (C16TMABr) at different initial concentrations. The organoclays were characterized by PXRD, TGA, FTIR and N2 adsorption isotherms. The ability of these samples to remove the dye eosin is evaluated. The removal properties of organoclays were dependent on the content of C16TMA cations, the initial concentrations of eosin, temperature of the removal process, the mass of the used organoclays. T...

  19. Origin of poor doping efficiency in solution processed organic semiconductors.

    Science.gov (United States)

    Jha, Ajay; Duan, Hong-Guang; Tiwari, Vandana; Thorwart, Michael; Miller, R J Dwayne

    2018-05-21

    Doping is an extremely important process where intentional insertion of impurities in semiconductors controls their electronic properties. In organic semiconductors, one of the convenient, but inefficient, ways of doping is the spin casting of a precursor mixture of components in solution, followed by solvent evaporation. Active control over this process holds the key to significant improvements over current poor doping efficiencies. Yet, an optimized control can only come from a detailed understanding of electronic interactions responsible for the low doping efficiencies. Here, we use two-dimensional nonlinear optical spectroscopy to examine these interactions in the course of the doping process by probing the solution mixture of doped organic semiconductors. A dopant accepts an electron from the semiconductor and the two ions form a duplex of interacting charges known as ion-pair complexes. Well-resolved off-diagonal peaks in the two-dimensional spectra clearly demonstrate the electronic connectivity among the ions in solution. This electronic interaction represents a well resolved electrostatically bound state, as opposed to a random distribution of ions. We developed a theoretical model to recover the experimental data, which reveals an unexpectedly strong electronic coupling of ∼250 cm -1 with an intermolecular distance of ∼4.5 Å between ions in solution, which is approximately the expected distance in processed films. The fact that this relationship persists from solution to the processed film gives direct evidence that Coulomb interactions are retained from the precursor solution to the processed films. This memory effect renders the charge carriers equally bound also in the film and, hence, results in poor doping efficiencies. This new insight will help pave the way towards rational tailoring of the electronic interactions to improve doping efficiencies in processed organic semiconductor thin films.

  20. Effect of compost age and composition on the atrazine removal from solution

    Science.gov (United States)

    Tsui, L.; Roy, W.R.

    2007-01-01

    Compost samples from two composting facilities, the Urbana (Illinois) Landscape Recycling Center (ULRC) and Illinois State University (ISU), were selected to examine the effect of compost age on atrazine removal from solution. The ULRC samples were made from yard waste without an additional nitrogen source. The ISU samples were made from yard waste or sawdust with the addition of manure. The 6-month-old ULRC compost had the greater capacity to remove atrazine from solution, which we attributed to its greater organic carbon content. The addition of nitrate into ULRC compost could influence the extent of atrazine removal, but did not have a significant impact on atrazine removal when applied to ISU compost, probably because manure was added to the yard waste to produce the compost. For both ULRC and ISU samples, the presence of sodium azide inhibited atrazine removal, suggesting that microbial activity contributed to the atrazine removal. Metabolic analysis demonstrated that hydroxyatrazine was the major identified metabolite that accumulated in solution before significant ring mineralization could occur. When compared with the ISU compost, the ULRC compost sample had a greater capacity to remove atrazine from solution during the 120 days of study because of the larger humic acid content. The experimental results suggested that less-mature compost may be better suited for environmental applications such as removing atrazine from tile-drainage waters. ?? 2006 Elsevier B.V. All rights reserved.

  1. Gum karaya based hydrogel nanocomposites for the effective removal of cationic dyes from aqueous solutions

    CSIR Research Space (South Africa)

    Mittala, H

    2016-02-01

    Full Text Available after nanocomposite formation with SiC NPs. The HNC was employed for the removal of cationic dyes, i.e., malachite green (MG) and rhodamine B (RhB) from the aqueous solution. The HNC was found to remove 91% (MG) and 86% (RhB) of dyes with a polymer dose...

  2. Removing ferric ions from concentrated acid leaching solution of an uranium ore by jarosite

    International Nuclear Information System (INIS)

    Song Huanbi; Hu Yezang

    1997-01-01

    The author expounds the fundamental rules of removing ferric ions by jarosite and presents results of removing ferric ions from concentrated acid curing-trickle leaching solution of an uranium ore. It turns out that the method can be applied to uranium hydrometallurgical process effectively

  3. Effect of compost age and composition on the atrazine removal from solution.

    Science.gov (United States)

    Tsui, Lo; Roy, William R

    2007-01-02

    Compost samples from two composting facilities, the Urbana (Illinois) Landscape Recycling Center (ULRC) and Illinois State University (ISU), were selected to examine the effect of compost age on atrazine removal from solution. The ULRC samples were made from yard waste without an additional nitrogen source. The ISU samples were made from yard waste or sawdust with the addition of manure. The 6-month-old ULRC compost had the greater capacity to remove atrazine from solution, which we attributed to its greater organic carbon content. The addition of nitrate into ULRC compost could influence the extent of atrazine removal, but did not have a significant impact on atrazine removal when applied to ISU compost, probably because manure was added to the yard waste to produce the compost. For both ULRC and ISU samples, the presence of sodium azide inhibited atrazine removal, suggesting that microbial activity contributed to the atrazine removal. Metabolic analysis demonstrated that hydroxyatrazine was the major identified metabolite that accumulated in solution before significant ring mineralization could occur. When compared with the ISU compost, the ULRC compost sample had a greater capacity to remove atrazine from solution during the 120 days of study because of the larger humic acid content. The experimental results suggested that less-mature compost may be better suited for environmental applications such as removing atrazine from tile-drainage waters.

  4. Efficient removal of malachite green dye using biodegradable graft copolymer derived from amylopectin and poly(acrylic acid).

    Science.gov (United States)

    Sarkar, Amit Kumar; Pal, Aniruddha; Ghorai, Soumitra; Mandre, N R; Pal, Sagar

    2014-10-13

    This article reports on the application of a high performance biodegradable adsorbent based on amylopectin and poly(acrylic acid) (AP-g-PAA) for removal of toxic malachite green dye (MG) from aqueous solution. The graft copolymer has been synthesized and characterized using various techniques including FTIR, GPC, SEM and XRD analyses. Biodegradation study suggests that the co-polymer is biodegradable in nature. The adsorbent shows excellent potential (Qmax, 352.11 mg g(-1); 99.05% of MG has been removed within 30 min) for removal of MG from aqueous solution. It has been observed that point to zero charge (pzc) of graft copolymer plays significant role in adsorption efficacy. The adsorption kinetics and isotherm follow pseudo-second order and Langmuir isotherm models, respectively. Thermodynamics parameters suggest that the process of dye uptake is spontaneous. Finally desorption study shows excellent regeneration efficiency of adsorbent. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Potential agents for removal of actinides from waste solutions

    International Nuclear Information System (INIS)

    Romanovski, V.V.; Whisenhunt, D.W.; Veeck, A.C.; Andersen, W.A.; Hoffman, D.C.; Jide, X.; White, D.; Raymond, K.N.

    1996-01-01

    The uptake of Th(IV) from nitric acid and hydrochloric acid solutions by chelating ion exchange resins containing catechol, 1,2- hydroxypyridinone (1,2-HOPO) and 3,4-hydroxypyridinone (3,4-HOPO) functional groups, has been investigated. These polystyrene based materials show excellent kinetics for uptake of Th(IV) and have a high loading capacity. Liquid/liquid extractants have also been synthesized by addition of lipophilic side chains to the chelating groups (1,2-HOPO; 3,4-HOPO; 3,2-HOPO; catecholamide; terephthalamide). The initial evaluation of the extraction properties has been carried out

  6. Methods for removing transuranic elements from waste solutions

    International Nuclear Information System (INIS)

    Slater, S.A.; Chamberlain, D.B.; Connor, C.; Sedlet, J.; Srinivasan, B.; Vandegrift, G.F.

    1994-11-01

    This report outlines a treatment scheme for separating and concentrating the transuranic (TRU) elements present in aqueous waste solutions stored at Argonne National Laboratory (ANL). The treatment method selected is carrier precipitation. Potential carriers will be evaluated in future laboratory work, beginning with ferric hydroxide and magnetite. The process will result in a supernatant with alpha activity low enough that it can be treated in the existing evaporator/concentrator at ANL. The separated TRU waste will be packaged for shipment to the Waste Isolation Pilot Plant

  7. Parametric study on removal efficiency of impregnated activated charcoal and silver zeolite for radioactive methyl iodide

    International Nuclear Information System (INIS)

    Shiomi, H.; Yuasa, Y.; Tani, A.; Ohki, M.; Nakagawa, T.

    1983-01-01

    The removal efficiency of impregnated activated charcoal and silver zeolite for radioactive methyl iodide is influenced by various parameters such as temperature, relative humidity, face velocity and packing density. This study is to evaluate the dependency of the removal efficiency on each parameter and these combined parameters, quantitatively. Four types of adsorbents, BC-727, AgX, CHC-50 and SS 208C 5KI 3 , were tested. From experimental data and mass transfer theory, an experimental equation for evaluating the removal efficiency of adsorbents was derived under a series of experiments for radioactive methyl iodine-131. It was concluded that the removal efficiency calculated from the experimental equation agreed well with the experimental value. Effects of experimental specific parameters, such as Pre-flow time, methyl iodide injection time and After-flow time, on the removal efficiency of adsorbent are also described

  8. Efficient numerical solution to vacuum decay with many fields

    Energy Technology Data Exchange (ETDEWEB)

    Masoumi, Ali; Olum, Ken D.; Shlaer, Benjamin, E-mail: ali@cosmos.phy.tufts.edu, E-mail: kdo@cosmos.phy.tufts.edu, E-mail: shlaer@cosmos.phy.tufts.edu [Institute of Cosmology, Department of Physics and Astronomy, Tufts University, Medford, MA 02155 (United States)

    2017-01-01

    Finding numerical solutions describing bubble nucleation is notoriously difficult in more than one field space dimension. Traditional shooting methods fail because of the extreme non-linearity of field evolution over a macroscopic distance as a function of initial conditions. Minimization methods tend to become either slow or imprecise for larger numbers of fields due to their dependence on the high dimensionality of discretized function spaces. We present a new method for finding solutions which is both very efficient and able to cope with the non-linearities. Our method directly integrates the equations of motion except at a small number of junction points, so we do not need to introduce a discrete domain for our functions. The method, based on multiple shooting, typically finds solutions involving three fields in around a minute, and can find solutions for eight fields in about an hour. We include a numerical package for Mathematica which implements the method described here.

  9. Development of new photocatalysts for efficient removal of ethylene

    DEFF Research Database (Denmark)

    Nielsen, Morten Godtfred

    The aim of this thesis has been to remove ethylene/ethene (from here on called ethene because it is shortest) photocatalytically with the primary purpose of preventing fruit ripening during shipping. This has been achieved based on TiO2. The topic has been approached from different angles. The most...

  10. Carbonised jackfruit peel as an adsorbent for the removal of Cd(II) from aqueous solution.

    Science.gov (United States)

    Inbaraj, B Stephen; Sulochana, N

    2004-08-01

    The fruit of the jack (Artocarpus heterophyllus) is one of the popular fruits in India, where the total area under this fruit is about 13,460 ha. A significant amount of peel (approximately 2,714-11,800 kg per tree per year) is discarded as agricultural waste, as apart from its use as a table fruit, it is popular in many culinary preparations. Treatment of jackfruit peel with sulphuric acid produced a carbonaceous product which was used to study its efficiency as an adsorbent for the removal of Cd(II) from aqueous solution. Batch experiments were performed as a function of process parameters; agitation time, initial metal concentration, adsorbent concentration and pH. Kinetic analyses made with Lagergren pseudo-first-order, Ritchie second-order and modified Ritchie second-order models showed better fits with modified Ritchie second-order model. The Langmuir-Freundlich (Sips equation) model best defined the experimental equilibrium data among the three isotherm models (Freundlich, Langmuir and Langmuir-Freundlich) tested. Taking a particular metal concentration, the optimum dose and pH required for the maximum metal removal was established. A complete recovery of the adsorbed metal ions from the spent adsorbent was achieved by using 0.01 M HCl.

  11. Effective removal of hexavalent mercury from aqueous solution by modified polymeric nanoadsorbent

    Directory of Open Access Journals (Sweden)

    Lida Rahmanzadeh

    2016-07-01

    Full Text Available Mercury is one of the most toxic metals present in the environment. Adsorption has been proposed among the technologies for mercury adsorbent. The kinetics of adsorption depends on the adsorbent concentration, and the physical and chemical characteristics of adsorbent. In this study we were used a novel adsorbent, magnetite-polyrhodanine core- shell nanoparticles, for removing Hg(II from aqueous solution. The effect of pH, initial Hg(II concentration, initial adsorbent concentration and contact time on the efficiency of Hg(II removal were investigated systematically by batch experiments. The maximum adsorption capacity was obtained 29.14 mg g-1 at PH=6.5 and 25°C with 10 g L-1 nano adsorbent. The kinetic data of adsorption of Hg(II ion on the synthesized adsorbent were best described by a pseudo- second- order equation, indicating their chemical adsorption. The Freundlich, Langmuir and Temkin isotherms were used to modeling of mercury adsorption on Hg(II in aqueous medium which modeled best by the Freundlich isotherm is whole concentration rage.

  12. Solute removal capacity of high cut-off membrane plasma separators.

    Science.gov (United States)

    Ohkubo, Atsushi; Kurashima, Naoki; Nakamura, Ayako; Miyamoto, Satoko; Iimori, Soichiro; Rai, Tatemitsu

    2013-10-01

    In vitro blood filtration was performed by a closed circuit using high cut-off membrane plasma separators, EVACURE EC-2A10 (EC-2A) and EVACURE EC-4A10 (EC-4A). Samples were obtained from sampling sites before the plasma separator, after each plasma separator, and from the ultrafiltrate of each separator. The sieving coefficient (S.C.) of total protein (TP), albumin (Alb), IgG, interleukin-6 (IL-6), interleukin-8 (IL-8), tumor necrosis factor-α (TNF-α), fibrinogen (Fib), antithrombin III (AT-III), and coagulation factor XIII (FXIII) were calculated. The S.C. of each solute using EC-2A and EC-A4 were as follows; TP: 0.25 and 0.56, Alb: 0.32 and 0.73, IgG: 0.16 and 0.50, IL-6:0.73 and 0.95, IL-8:0.85 and 0.82, TNF-α: 1.07 and 0.99, Fib: 0 and 0, FXIII: 0.07 and 0.17, respectively. When compared with the conventional type of membrane plasma separators, EVACURE could efficiently remove cytokines while retaining coagulation factors such as fibrinogen. Moreover, EC-2A prevented protein loss, whereas EC-4A could remove approximately 50% of IgG. © 2013 The Authors. Therapeutic Apheresis and Dialysis © 2013 International Society for Apheresis.

  13. The applications of populus fiber in removal of Cr{sup (VI)} from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Li, Miaomiao; Gong, Yumei, E-mail: ymgong@dlpu.edu.cn; Lyu, Aichao; Liu, Yuanfa, E-mail: morning309@126.com; Zhang, Hong, E-mail: zhang_hong1234@sina.com

    2016-10-15

    Highlights: • A sorbent for heavy metal ions based on populus fibers is prepared by a green way. • The chromium adsorption on the sorbent accords with the pseudo-second-order kinetics. • The proposed adsorption involves static attraction and chelation by the sorbent on chromium. • The sorbent is expected to be applied in universal conditions. - Abstract: The surface modification of natural materials to be applied in removal of Cr{sup (VI)} from aqueous solutions has attracted much attention. A natural sorbent for Cr{sup (VI)} based on natural populus fibers (PF) is prepared by transforming the cyano groups (AN) in polyacrylonitriles (PAN) grafted from PF into amidoxime groups (AO), which has strong ability to attract and chelate heavy metal ions. The prepared sorbent is characterized by Fourier Transform Infrared Spectra (FT-IR), thermogravimetric analysis (TGA), solid-state nuclear magnetic resonance ({sup 13}C NMR) and scanning electron microscope (SEM). As potassium dichromate solution (K{sub 2}Cr{sub 2}O{sub 7}) is used as a target solution for detecting adsorption capacity of the sorbent, the adsorption kinetics of the sorbent for chromiun is consistent with the pseudo-second-order kinetic model by analyzing the adsorption amount as a function of the sorbent dispersed duration in solution at pH = 2. The expected adsorption mechanism is that the Cr{sup (VI)} in anionic ions Cr{sub 2}O{sub 7}{sup 2−} and HCrO{sub 4}{sup −} are adsorbed through electrostatic attraction but when Cr{sup (VI)} is reduced to Cr{sup (III)} by AO, the electronegative nitrogen and oxygen in AO chelate it through coordination bond. The as-prepared PF derivant with high adsorption efficiency of chromium 180.5 mg/g (3.47 mmol/g), low cost, reusability and greenly preparation process suggests that the development of natural PF as a sorbent in removal of Cr{sup (VI)} from aqueous solutions is a destined significant approach.

  14. Statistical estimate of mercury removal efficiencies for air pollution control devices of municipal solid waste incinerators.

    Science.gov (United States)

    Takahashi, Fumitake; Kida, Akiko; Shimaoka, Takayuki

    2010-10-15

    Although representative removal efficiencies of gaseous mercury for air pollution control devices (APCDs) are important to prepare more reliable atmospheric emission inventories of mercury, they have been still uncertain because they depend sensitively on many factors like the type of APCDs, gas temperature, and mercury speciation. In this study, representative removal efficiencies of gaseous mercury for several types of APCDs of municipal solid waste incineration (MSWI) were offered using a statistical method. 534 data of mercury removal efficiencies for APCDs used in MSWI were collected. APCDs were categorized as fixed-bed absorber (FA), wet scrubber (WS), electrostatic precipitator (ESP), and fabric filter (FF), and their hybrid systems. Data series of all APCD types had Gaussian log-normality. The average removal efficiency with a 95% confidence interval for each APCD was estimated. The FA, WS, and FF with carbon and/or dry sorbent injection systems had 75% to 82% average removal efficiencies. On the other hand, the ESP with/without dry sorbent injection had lower removal efficiencies of up to 22%. The type of dry sorbent injection in the FF system, dry or semi-dry, did not make more than 1% difference to the removal efficiency. The injection of activated carbon and carbon-containing fly ash in the FF system made less than 3% difference. Estimation errors of removal efficiency were especially high for the ESP. The national average of removal efficiency of APCDs in Japanese MSWI plants was estimated on the basis of incineration capacity. Owing to the replacement of old APCDs for dioxin control, the national average removal efficiency increased from 34.5% in 1991 to 92.5% in 2003. This resulted in an additional reduction of about 0.86Mg emission in 2003. Further study using the methodology in this study to other important emission sources like coal-fired power plants will contribute to better emission inventories. Copyright © 2010 Elsevier B.V. All rights

  15. Efficient removal of trace antimony(III) through adsorption by hematite modified magnetic nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Shan, Chao; Ma, Zhiyao; Tong, Meiping, E-mail: tongmeiping@pku.edu.cn

    2014-03-01

    Graphical abstract: - Highlights: • Sb(III) adsorption capacity of MNP@hematite was twice that of commercial Fe{sub 3}O{sub 4}. • pH, ionic strength, coexisting anions and NOM did not inhibit Sb(III) removal. • MNP@hematite could remove trace Sb(III) and As(III) from water simultaneously. • Efficient removal of Sb(III) from real tap water was achieved. • MNP@hematite could be easily recycled with a magnet and could be used repeatedly. - Abstract: Hematite coated magnetic nanoparticle (MNP@hematite) was fabricated through heterogeneous nucleation technique and used to remove trace Sb(III) from water. Powder X-ray diffraction, transmission electron microscopy (TEM), and alternating gradient magnetometry were utilized to characterize the prepared adsorbent. TEM image showed that MNP@hematite particles were spherical with size of 10–30 nm. With saturation magnetization of 27.0 emu/g, MNP@hematite particles could be easily separated from water with a simple magnetic process in short time (5 min). At initial concentration of 110 μg/L, Sb(III) was rapidly decreased to below 5 μg/L by MNP@hematite in 10 min. Sb(III) adsorption capacity of MNP@hematite was 36.7 mg/g, which was almost twice that of commercial Fe{sub 3}O{sub 4} nanoparticles. The removal of trace Sb(III) was not obviously affected by solution pH (over a wide range from 3 to 11), ionic strength (up to 100 mM), coexisting anions (chloride, nitrate, sulfate, carbonate, silicate, and phosphate, up to 10 mM) and natural organic matters (humic acid and alginate, up to 8 mg/L as TOC). Moreover, MNP@hematite particles were able to remove Sb(III) and As(III) simultaneously. Trace Sb(III) could also be effectively removed from real tap water by MNP@hematite. The magnetic adsorbent could be recycled and used repeatedly.

  16. Efficient removal of trace antimony(III) through adsorption by hematite modified magnetic nanoparticles

    International Nuclear Information System (INIS)

    Shan, Chao; Ma, Zhiyao; Tong, Meiping

    2014-01-01

    Graphical abstract: - Highlights: • Sb(III) adsorption capacity of MNP@hematite was twice that of commercial Fe 3 O 4 . • pH, ionic strength, coexisting anions and NOM did not inhibit Sb(III) removal. • MNP@hematite could remove trace Sb(III) and As(III) from water simultaneously. • Efficient removal of Sb(III) from real tap water was achieved. • MNP@hematite could be easily recycled with a magnet and could be used repeatedly. - Abstract: Hematite coated magnetic nanoparticle (MNP@hematite) was fabricated through heterogeneous nucleation technique and used to remove trace Sb(III) from water. Powder X-ray diffraction, transmission electron microscopy (TEM), and alternating gradient magnetometry were utilized to characterize the prepared adsorbent. TEM image showed that MNP@hematite particles were spherical with size of 10–30 nm. With saturation magnetization of 27.0 emu/g, MNP@hematite particles could be easily separated from water with a simple magnetic process in short time (5 min). At initial concentration of 110 μg/L, Sb(III) was rapidly decreased to below 5 μg/L by MNP@hematite in 10 min. Sb(III) adsorption capacity of MNP@hematite was 36.7 mg/g, which was almost twice that of commercial Fe 3 O 4 nanoparticles. The removal of trace Sb(III) was not obviously affected by solution pH (over a wide range from 3 to 11), ionic strength (up to 100 mM), coexisting anions (chloride, nitrate, sulfate, carbonate, silicate, and phosphate, up to 10 mM) and natural organic matters (humic acid and alginate, up to 8 mg/L as TOC). Moreover, MNP@hematite particles were able to remove Sb(III) and As(III) simultaneously. Trace Sb(III) could also be effectively removed from real tap water by MNP@hematite. The magnetic adsorbent could be recycled and used repeatedly

  17. Application of Moringa Peregrina seed extract as a natural coagulant for Phenol removal from aqueous solution

    Directory of Open Access Journals (Sweden)

    Edris Bazrafshan

    2013-02-01

    Conclusion: According to the obtained results, Moringa peregrina seed extract, with respect to its high efficacy, can be used as an effective, efficient, and inexpensive coagulant in removing phenol from aqueous environments.

  18. Efficient removal of chromate and arsenate from individual and mixed system by malachite nanoparticles.

    Science.gov (United States)

    Saikia, Jiban; Saha, Bedabrata; Das, Gopal

    2011-02-15

    Malachite nanoparticles of 100-150 nm have been efficiently and for the first time used as an adsorbent for the removal of toxic arsenate and chromate. We report a high adsorption capacity for chromate and arsenate on malachite nanoparticle from both individual and mixed solution in pH ∼4-5. However, the adsorption efficiency decreases with the increase of solution pH. Batch studies revealed that initial pH, temperature, malachite nanoparticles dose and initial concentration of chromate and arsenate were important parameters for the adsorption process. Thermodynamic analysis showed that adsorption of chromate and arsenate on malachite nanoparticles is endothermic and spontaneous. The adsorption of these anions has also been investigated quantitatively with the help of adsorption kinetics, isotherm, and selectivity coefficient (K) analysis. The adsorption data for both chromate and arsenate were fitted well in Langmuir isotherm and preferentially followed the second order kinetics. The binding affinity of chromate is found to be slightly higher than arsenate in a competitive adsorption process which leads to the comparatively higher adsorption of chromate on malachite nanoparticles surface. Copyright © 2010 Elsevier B.V. All rights reserved.

  19. A novel biochar derived from cauliflower (Brassica oleracea L.) roots could remove norfloxacin and chlortetracycline efficiently.

    Science.gov (United States)

    Qin, Tingting; Wang, Zhaowei; Xie, Xiaoyun; Xie, Chaoran; Zhu, Junmin; Li, Yan

    2017-12-01

    The biochar was prepared by pyrolyzing the roots of cauliflowers, at a temperature of 500 °C under oxygen-limited conditions. The structure and characteristics of the biochar were examined using scanning electron microscopy, an energy dispersive spectrometer, a zeta potential analyzer, and Fourier transform infrared spectroscopy. The effects of the temperature, the initial pH, antibiotic concentration, and contact time on the adsorption of norfloxacin (NOR) and chlortetracycline (CTC) onto the biochar were investigated. The adsorption kinetics of NOR and CTC onto the biochar followed the pseudo-second-order kinetic and intra-particle diffusion models. The adsorption isotherm experimental data were well fitted to the Langmuir and Freundlich isotherm models. The maximum adsorption capacities of NOR and CTC were 31.15 and 81.30 mg/g, respectively. There was little difference between the effects of initial solution pH (4.0-10.0) on the adsorption of NOR or CTC onto the biochar because of the buffering effect. The biochar could remove NOR and CTC efficiently in aqueous solutions because of its large specific surface area, abundant surface functional groups, and particular porous structure. Therefore, it could be used as an excellent adsorbent material because of its low cost and high efficiency and the extensive availability of the raw materials.

  20. Removal of nitrate, ammonia and phosphate from aqueous solutions in packed bed filter using biochar augmented sand media

    Directory of Open Access Journals (Sweden)

    El Hanandeh Ali

    2017-01-01

    Full Text Available Nutrients from wastewater are a major source of pollution because they can cause significant impact on the ecosystem. Accordingly, it is important that the nutrient concentrations are kept to admissible levels to the receiving environment. Often regulatory limits are set on the maximum allowable concentrations in the effluent. Therefore, wastewater must be treated to meet safe levels of discharge. In this study, laboratory investigation of the efficiency of packed bed filters to remove nitrate, ammonium and phosphate from aqueous solutions were conducted. Sand and sand augmented with hydrochloric acid treated biochar (SBC were used as packing media. Synthetic wastewater solution was prepared with PO43−, NO3−, NH4+ concentrations 20, 10, 50 mg/L, respectively. Each experiment ran for a period of five days; samples from the effluent were collected on alternate days. All experiments were duplicated. Over the experiment period, the average removal efficiency of PO43−, NO3−, NH4+ were 99.2%, 72.9%, 96.7% in the sand packed columns and 99.2%, 82.3%, 97.4% in the SBC packed columns, respectively. Although, the presence of biochar in the packing media had little effect on phosphate and ammonium removal, it significantly improved nitrate removal.

  1. Removal of Hexavalent Chromium from Aqueous Solution by Modified Holly Sawdust: A Study of Equilibrium and Kinetics

    Directory of Open Access Journals (Sweden)

    S. Azizian

    2010-01-01

    Full Text Available Introduction & Objective: Industrial wastewaters including heavy metals, are among the important sources of environmental pollution. Heavy metals such as chromium are found in plating wastewater and is harmful for human health and environment. The purpose of the present study was to investigate the absorption of heavy metals such as chromium onto modified holly sawdust as an cheaper absorbent. Materials & Methods: This study was a fundamental- application study done in Hamadan University of Medical Sciences, hygiene faculty water and wastewater chemistry laboratory. This study investigated the removal of hexavalent chromium by using modified holly sawdust with pH changes ,contact time ,absorbent dose and Cr(VI concentrations in batch system. Then the result was analyzed by Excel software.Results: The results showed that the removal efficiency decrease is accompanied by the increase of pH and initial chromium concentration. pH increase from 2 to 12(equilibrium time= 180 min, adsorbent dose= 0.6g/100CC, Cr(VI concentrations= 60 mg/L,leaded to the removal efficiency decrease from 99.67 % to 29.78 %. Also removal efficiency decreased from 99.37 % to 40.24 % after increasing the initial chromium concentrations from 20 mg/L to 100 mg/L. Moreover the results showed the removal efficiency increased after increasing the adsorbent dose and contact time. By increasing adsorbent dose from 0.2 g/100CC to 1 g/100CC, the removal efficiency increased from 34.65 % to 99.76 %.Additionally, the removal efficiency increased from 48.53%to 99.76% by increasing contact time from 5 mins to 180 mins. Experimental isotherms and kinetics models were assessed by Langmuir and Freundlich isotherms and pseudo-first-order and pseudo-second-order kinetics models. The results showed that the data were acceptably explained acceptably by Langmuir isotherms and pseudo-second-order kinetics models respectively.Conclusion: The results showed that the removal of hexavalent chromium

  2. Evaluation of solvents efficiency in condensate banking removal

    OpenAIRE

    CORREA, TOMAS; TIAB, DJEBBAR; REST, DORA PATRICIA

    2009-01-01

    Este estudio describe el montaje experimental y las pruebas realizadas en el laboratorio para simular las condiciones de un yacimiento de gas condensado por debajo del punto de burbuja usando tres diferentes composiciones sintéticas de gas condensado. Metanol, Propanol y cloruro de metileno son los solventes usados para remover el banco de condensado y mejorar la permeabilidad efectiva al gas en la cara del núcleo. Ellos son inyectados en areniscas Berea con propiedades petrofísicas similares...

  3. Removal of copper from aqueous solution by electrodeposition in cathode chamber of microbial fuel cell.

    Science.gov (United States)

    Tao, Hu-Chun; Liang, Min; Li, Wei; Zhang, Li-Juan; Ni, Jin-Ren; Wu, Wei-Min

    2011-05-15

    Based on energetic analysis, a novel approach for copper electrodeposition via cathodic reduction in microbial fuel cells (MFCs) was proposed for the removal of copper and recovery of copper solids as metal copper and/or Cu(2)O in a cathode with simultaneous electricity generation with organic matter. This was examined by using dual-chamber MFCs (chamber volume, 1L) with different concentrations of CuSO(4) solution (50.3 ± 5.8, 183.3 ± 0.4, 482.4 ± 9.6, 1007.9 ± 52.0 and 6412.5 ± 26.7 mg Cu(2+)/L) as catholyte at pH 4.7, and different resistors (0, 15, 390 and 1000 Ω) as external load. With glucose as a substrate and anaerobic sludge as an inoculum, the maximum power density generated was 339 mW/m(3) at an initial 6412.5 ± 26.7 mg Cu(2+)/L concentration. High Cu(2+) removal efficiency (>99%) and final Cu(2+) concentration below the USA EPA maximum contaminant level (MCL) for drinking water (1.3mg/L) was observed at an initial 196.2 ± 0.4 mg Cu(2+)/L concentration with an external resistor of 15 Ω, or without an external resistor. X-ray diffraction analysis confirmed that Cu(2+) was reduced to cuprous oxide (Cu(2)O) and metal copper (Cu) on the cathodes. Non-reduced brochantite precipitates were observed as major copper precipitates in the MFC with a high initial Cu(2+) concentration (0.1M) but not in the others. The sustainability of high Cu(2+) removal (>96%) by MFC was further examined by fed-batch mode for eight cycles. Copyright © 2011 Elsevier B.V. All rights reserved.

  4. Synthesis of hydroxyapatite/multi-walled carbon nanotubes for the removal of fluoride ions from solution

    Science.gov (United States)

    Ruan, Zhongyuan; Tian, Yaxi; Ruan, Jifu; Cui, Guijia; Iqbal, Kanwal; Iqbal, Anam; Ye, Herui; Yang, Zhangzhong; Yan, Shiqiang

    2017-08-01

    A novel composite material, hydroxyapatite (HA)-multi-walled carbon nanotubes (MWCNTs), was prepared using a simple in-situ sol-gel method, and was used for the first time to remove fluoride from water. The novel HA-MWCNTs were characterized using TEM, FT-IR, BET and XRD analysis. The TEM and SAED results revealed that the MWCNTs were uniformly encapsulated by hydroxyapatite nanoparticles. The synthesized HA-MWCNTs had a high specific surface area (180.504 m2 g-1), with an average pore width (14.607 nm) and pore volume (0.774 cm3 g-1), which produced a defluoridation capacity (DC) of 30.22 mgF- g-1. This value was greater than unmodified hydroxyapatite (HA), which exhibited a larger specific surface area (172.233 m2 g-1) and an excellent DC of 17.80 mgF- g-1. A number of pertinent parameters that could affect the defluoridation performance of the HA/MWCNTs including weight ratios of the two key materials, solution pH and competing anions were carefully and comprehensively examined. It was found that the adsorption results followed the Langmuir and Freundlich isotherm model, and the sorption kinetics of the F- appeared to exhibit a pseudo second order. Moreover, the adsorption reaction was spontaneous and endothermic and appeared to exhibit a higher initial adsorption rate. This reaction appeared to occur result from both anion exchange and electrostatic interactions. When the HA-MWCNTs (MH6) were at an adsorbent dose of 2.0 g L-1, they were able to decrease the fluoride concentration of actual nuclear industry wastewater from 8.79 mg L-1 to about 0.25 mg L-1 (97.15% removal efficiency). The experimental results of this study showed that the HA-MWCNTs composites have application potential for the removal of fluoride ions from wastewater.

  5. EVALUATION OF SOLVENTS EFFICIENCY IN CONDENSATE BANKING REMOVAL

    Directory of Open Access Journals (Sweden)

    TOMAS CORREA

    2009-01-01

    Full Text Available Este estudio describe el montaje experimental y las pruebas realizadas en el laboratorio para simular las condiciones de un yacimiento de gas condensado por debajo del punto de burbuja usando tres diferentes composiciones sintéticas de gas condensado. Metanol, Propanol y cloruro de metileno son los solventes usados para remover el banco de condensado y mejorar la permeabilidad efectiva al gas en la cara del núcleo. Ellos son inyectados en areniscas Berea con propiedades petrofísicas similares con el fin de comparar el grado de eficiencia en la remoción del banco de condensado. Los experimentos muestran que los tres solventes mejoraron la permeabilidad efectiva al gas después de remover el banco de condensado; sin embargo el metanol fue el solvente más eficiente para remover el banco de condensado, mientras el cloruro de metileno mostró los valores más bajos de permeabilidad efectiva al gas indicando menor eficiencia en la remoción el banco de condensado.

  6. Impact of removable partial denture prosthesis on chewing efficiency

    Science.gov (United States)

    BESSADET, Marion; NICOLAS, Emmanuel; SOCHAT, Marine; HENNEQUIN, Martine; VEYRUNE, Jean-Luc

    2013-01-01

    Removable partial denture prostheses are still being used for anatomic, medical and economic reasons. However, the impact on chewing parameters is poorly described. Objectives The objective of this study was to estimate the impact of removable partial denture prosthesis on masticatory parameters. Material and Methods Nineteen removable partial denture prosthesis (RPDP) wearers participated in the study. Among them, 10 subjects were Kennedy Class III partially edentulous and 9 with posterior edentulism (Class I). All presented a complete and full dentate opposing arch. The subjects chewed samples of carrots and peanuts with and without their prosthesis. The granulometry of the expectorated boluses from carrot and peanuts was characterized by median particle size (D50), determined at the natural point of swallowing. Number of chewing cycles (CC), chewing time (CT) and chewing frequency (CF=CC/CT) were video recorded. Results With RPDP, the mean D50 values for carrot and peanuts were lower [Repeated Model Procedures (RMP), F=15, p<0.001] regardless of the type of Kennedy Class. For each food, mean CC, CT and CF values recorded decreased (RMP, F=18, F=9, and F=20 respectively, p<0.01). With or without RPD, the boluses' granulometry values were above the masticatory normative index (MNI) determined as 4,000 µm. Conclusion RPDP rehabilitation improves the ability to reduce the bolus particle size, but does not reestablish fully the masticatory function. Clinical relevance This study encourages the clinical improvement of oral rehabilitation procedure. PMID:24212983

  7. Textile Dye Removal from Aqueous Solution using Modified Graphite Waste/Lanthanum/Chitosan Composite

    Science.gov (United States)

    Kusrini, E.; Wicaksono, B.; Yulizar, Y.; Prasetyanto, EA; Gunawan, C.

    2018-03-01

    We investigated various pre-treatment processes of graphite waste using thermal, mechanical and chemical methods. The aim of this work is to study the performance of modified graphite waste/lanthanum/chitosan composite (MG) as adsorbent for textile dye removal from aqueous solution. Effect of graphite waste resources, adsorbent size and lanthanum concentration on the dye removal were studied in batch experiments. Selectivity of MG was also investigated. Pre-heated graphite waste (NMG) was conducted at 80°C for 1 h, followed by mechanical crushing of the resultant graphite to 75 μm particle size, giving adsorption performance of ˜58%, ˜67%, ˜93% and ˜98% of the model dye rhodamine B (concentration determined by UV-vis spectroscopy at 554 nm), methyl orange (464 nm), methylene blue (664 nm) and methyl violet (580 nm), respectively from aqueous solution. For this process, the system required less than ˜5 min for adsorbent material to be completely saturated with the adsorbate. Further chemical modification of the pre-treated graphite waste (MG) with lanthanum (0.01 – V 0.03 M) and chitosan (0.5% w/w) did not improve the performance of dye adsorption. Under comparable experimental conditions, as those of the ‘thermal-mechanical-pre-treated-only’ (NMG), modification of graphite waste (MG) with 0.03 M lanthanum and 0.5% w/w chitosan resulted in ˜14%, ˜47%, ˜72% and ˜85% adsorption of rhodamine B, methyl orange, methylene blue and methyl violet, respectively. Selective adsorption of methylene blue at most to ˜79%, followed by methyl orange, methyl violet and rhodamine B with adsorption efficiency ˜67, ˜38, and ˜9% sequentially using MG with 0.03 M lanthanum and 0.5% w/w chitosan.

  8. Removal of 4-chlorobenzoic acid from spiked hydroponic solution by willow trees (Salix viminalis)

    DEFF Research Database (Denmark)

    Deavers, K.; Macek, T.; Karlson, U.

    2010-01-01

    . Methods The removal of 4-CBA by willow trees was investigated with intact, septic willow trees growing in hydroponic solution and with sterile cell suspensions at concentrations of 5 mg/L and 50 mg/L 4-CBA. Nutrient solutions with different levels of ammonium and nitrate were prepared to achieve different...

  9. Removal of Cr(VI) from aqueous solution by flocculant with the capacity of reduction and chelation

    International Nuclear Information System (INIS)

    Wang, Gang; Chang, Qing; Han, Xiaoting; Zhang, Mingyue

    2013-01-01

    Highlights: ► We report a novel flocculant with the properties of reduction and chelation for Cr. ► The removal of Cr(VI) by the flocculant depends highly on pH value. ► Some coexisting ions inhibit Cr (VI) removal, but promote total Cr removal. ► Cr and turbidity can be removed simultaneously in the treated wastewater. ► The interaction mechanism is investigated by FTIR and SEM. -- Abstract: A novel agent polyethyleneimine-sodium xanthogenate (PEX) with the multifunction of reduction, chelation, flocculation and precipitation was synthesized by using polyethyleneimine (PEI), carbon disulfide (CS 2 ), and sodium hydroxide (NaOH). The effects of different important parameters, such as pH value, initial Cr(VI) concentration, coexisting ions and turbidity etc., on the removal of chromium from aqueous solution by PEX were investigated in flocculation experiments. The experiments results demonstrated that PEX could efficiently remove Cr(VI) and total Cr (Cr(VI) + Cr(III)) in strongly acidic media. It was proved that the presence of coexisting ions (Na + , Ca 2+ , F − , Cl − , and SO 4 2− ) in the solution had a little influence on the removal of chromium. Furthermore, it was conformed that Cr(VI) ions and turbidity could be simultaneously removed when water samples contained both Cr(VI) ions and turbidity. Finally, the mechanism of interaction between chromium and PEX was further confirmed by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The results reveal that dithiocarboxylic acid groups on PEX macromolecule play a major role in Cr(VI) reduction and Cr(III) chelation, and the flocs formation is attributed to the interparticle bridging mechanism of PEX

  10. Synthesis of a magnetic composite resin and its cobalt removal characteristics in aqueous solution

    International Nuclear Information System (INIS)

    Kim, Young Kyun; Lee, Kun Jai

    2001-01-01

    A series of stepwise procedures to prepare a new organic-inorganic composite magnetic resin with phenolsulphonic-formaldehyde and freshly formed iron ferrite was established, based upon wet-and-neutralization method for synthesizing iron ferrite and pearl-polymerization method for synthesizing rigid bead-type composite resin. The ion exchange and sorption characteristics of the composite resin prepared by the above method at various conditions were experimentally disclosed. The composite resin prepared shows stably high removal efficiency to Co(II) species in aqueous solution in a wide range of solution pH. The overall isotherm is qualitatively explained by the generalized adsorption isotherm concept proposed by McKinley. The standard enthalpy change derived from van't Hoff equation conforms to the typical range for chemisorption or ion exchange. The selectivity of the PSF-F (phenolsulphonic formaldehyde-iron ferrite) composite resin to Co(II) species and other competing chemicals (i.e. Na 2 EDTA, Ca(II) and Na) was compared. It is anticipated that the composite resin can also be used for column-operation with process-control by applying external magnetic field, since the rigid bead-type composite resin shows magnetic-susceptibility due to its paramagnetic inorganic constituent (i.e. iron ferrite). (author)

  11. An Efficient Series Solution for Nonlinear Multiterm Fractional Differential Equations

    Directory of Open Access Journals (Sweden)

    Moh’d Khier Al-Srihin

    2017-01-01

    Full Text Available In this paper, we introduce an efficient series solution for a class of nonlinear multiterm fractional differential equations of Caputo type. The approach is a generalization to our recent work for single fractional differential equations. We extend the idea of the Taylor series expansion method to multiterm fractional differential equations, where we overcome the difficulty of computing iterated fractional derivatives, which are difficult to be computed in general. The terms of the series are obtained sequentially using a closed formula, where only integer derivatives have to be computed. Several examples are presented to illustrate the efficiency of the new approach and comparison with the Adomian decomposition method is performed.

  12. Efficient Solutions for New Homes Case Study: Savannah Gardens

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-03-15

    The Savannah Housing Department is leading sustainable and affordable housing development in Georgia. It partnered with Southface Energy Institute, a member of the U.S. Department of Energy’s Partnership for Home Innovation Building America research team, to seek cost-effective solutions for increasing the energy efficiency of the Savannah Housing Department’s standard single-family home plans in the Savannah Gardens Community. Based on engineering, cost, and constructability analyses, the combined research team chose to pilot two technologies to evaluate efficiency and comfort impacts for homeowners: a heat-pump water heater in an encapsulated attic and an insulated exterior wall sheathing.

  13. Mercury Removal From Aqueous Solutions With Chitosan-Coated Magnetite Nanoparticles Optimized Using the Box-Behnken Design

    Science.gov (United States)

    Rahbar, Nadereh; Jahangiri, Alireza; Boumi, Shahin; Khodayar, Mohammad Javad

    2014-01-01

    Background: Nowadays, removal of heavy metals from the environment is an important problem due to their toxicity. Objectives: In this study, a modified method was used to synthesize chitosan-coated magnetite nanoparticles (CCMN) to be used as a low cost and nontoxic adsorbent. CCMN was then employed to remove Hg2+ from water solutions. Materials and Methods: To remove the highest percentage of mercury ions, the Box-Behnken model of response surface methodology (RSM) was applied to simultaneously optimize all parameters affecting the adsorption process. Studied parameters of the process were pH (5-8), initial metal concentration (2-8 mg/L), and the amount of damped adsorbent (0.25-0.75 g). A second-order mathematical model was developed using regression analysis of experimental data obtained from 15 batch runs. Results: The optimal conditions predicted by the model were pH = 5, initial concentration of mercury ions = 6.2 mg/L, and the amount of damped adsorbent = 0.67 g. Confirmatory testing was performed and the maximum percentage of Hg2+ removed was found to be 99.91%. Kinetic studies of the adsorption process specified the efficiency of the pseudo second-order kinetic model. The adsorption isotherm was well-fitted to both the Langmuir and Freundlich models. Conclusions: CCMN as an excellent adsorbent could remove the mercury ions from water solutions at low and moderate concentrations, which is the usual amount found in environment. PMID:24872943

  14. Protein-bound solute removal during extended multipass versus standard hemodialysis

    DEFF Research Database (Denmark)

    Eloot, Sunny; Van Biesen, Wim; Axelsen, Mette

    2015-01-01

    and middle molecules compared to standard hemodialysis (SHD). Since protein-bound solutes (PBS) exert important pathophysiological effects, we investigated whether MPHD results in improved removal of PBS as well. METHODS: A cross-over study (Clinical Trial NCT01267760) was performed in nine stable HD......), hippuric acid (HA), indole acetic acid (IAA), indoxyl sulfate (IS), and p-cresylsulfate (PCS). Dialyser extraction ratio, reduction ratio, and solute removal were calculated for these solutes. RESULTS: Already at 60 min after dialysis start, the extraction ratio in the hemodialyser was a factor 1.4-4 lower...

  15. Study of the removal of cesium from aqueous solutions by graphene oxide

    International Nuclear Information System (INIS)

    Bueno, Vanessa N.; Rodrigues, Debora F.; Vitta, Patricia B. Di

    2013-01-01

    Graphene oxide, used in this work, was synthesized from the oxidation of graphite by Hummer method. The experiments were performed in batch and analyzed for the following parameters: contact time, pH, cesium ion concentration in aqueous solution and removing capacity of the graphene oxide. After the experiments the samples were vacuum filtered and the remaining cesium in solution was quantified by Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). The equilibrium was reached after 60 minutes of contact in neutral solution. The percentage of removal was around 80%

  16. Sulphate Removal from Water by Carbon Residue from Biomass Gasification: Effect of Chemical Modification Methods on Sulphate Removal Efficiency

    Directory of Open Access Journals (Sweden)

    Hanna Runtti

    2016-02-01

    Full Text Available Sulphate removal from mine water is a problem because traditional chemical precipitation does not remove all sulphates. In addition, it creates lime sediment as a secondary waste. Therefore, an inexpensive and environmental-friendly sulphate removal method is needed in addition to precipitation. In this study, carbon residues from a wood gasification process were repurposed as precursors to a suitable sorbent for SO42- ion removal. The raw material was modified using ZnCl2, BaCl2, CaCl2, FeCl3, or FeCl2. Carbon residues modified with FeCl3 were selected for further consideration because the removal efficiency toward sulphate was the highest. Batch sorption experiments were performed to evaluate the effects of the initial pH, initial SO42- ion concentration, and contact time on sulphate removal. The removal of SO42- ions using Fe-modified carbon residue was notably higher compared with unmodified carbon residue and commercially available activated carbon. The sorption data exhibited pseudo-second-order kinetics. The isotherm analysis indicated that the sorption data of Fe-modified carbon residues can be represented by the bi-Langmuir isotherm model.

  17. Zinc, nickel, and cobalt ions removal from aqueous solution and plating plant wastewater by modified Aspergillus flavus biomass: A dataset

    Directory of Open Access Journals (Sweden)

    Rauf Foroutan

    2017-06-01

    Full Text Available The biomass of Aspergillus flavus was modified by calcium chloride to achieve a bioadsorbent for treating nickel, cobalt, and zinc ions from aqueous solutions. The information of pH, bioadsorbent dose, contact time, and temperature effect on the removal efficiency are presented. The data of Freundlich and Langmuir isotherm and pseudo-first-order and pseudo-second-order kinetic models are also depicted. The data showed that the maximum bioadsorption capacity of nickel, cobalt, and zinc ions is 32.26, 31.06 and 27.86 mg/g, respectively. The suitability of the bioadsorbent in heavy metals removal at field condition was tested with a real wastewater sample collected from a plating plant in the final part of this dataset. Based on the findings, the bioadsorbent was shown to be an affordable alternative for the removal of metals in the wastewater.

  18. Fixed bed column study for Cu (II) removal from aqueous solution using water hyacinth (Eichornia crassipes) biomass.

    Science.gov (United States)

    Gandhimathi, R; Ramesh, S T; Yadu, Anubhav; Bharathi, K S

    2013-07-01

    This paper reports the results of the study on the performance of low-cost biosorbent water hyacinth (WH) in removing Cu (II) from aqueous solution. The adsorbent material adopted was found to be an efficient media for the removal of Cu (II) in continuous mode using fixed bed column. The column studies were conducted with 10 mg/L metal solution with a flow rate of 10 mL/min with different bed depths such as 10, 20 and 30 cm. The column design parameters like adsorption rate constant, adsorption capacity and minimum bed depth were calculated. It was found that, the adsorption capacity of copper ions by water hyacinth increased by increasing the bed depth and the contact time.

  19. Simultaneous removal and recovery of uranium from aqueous solution using TiO_2 photoelectrochemical reduction method

    International Nuclear Information System (INIS)

    Huichao He; Meirong Zong; Faqin Dong; Southwest University of Science and Technology, Sichuan; Pengpan Yang; Gaili Ke; Mingxue Liu; Xiaoqin Nie; Wei Ren; Liang Bian; Southwest University of Science and Technology, Sichuan; Chinese Academy of Sciences, Xinjiang

    2017-01-01

    U(VI)-containing wastewater has potential radiation hazard to the environment, but contains valuable uranium resource. Based on the reduction of U(VI) and the difference in solubility between U(VI) and U(IV), here we construct a TiO_2-based photoelectrochemical cell to remove U(VI) and recover uranium from aqueous solution. By irradiating TiO_2 photoanode at E = 0.45 V versus SCE, U(VI) can be simultaneously removed from aqueous solution and recovered as solid uranium compounds on a FTO glass cathode. Since ethanol can act as hole scavenger to protect the formed U(IV) and provide CO_2"−"· as reductant, ethanol adding improved the U(VI) reduction efficiency of TiO_2-based photoelectrochemical cell. (author)

  20. Highly efficient removal of trace thallium from contaminated source waters with ferrate: Role of in situ formed ferric nanoparticle.

    Science.gov (United States)

    Liu, Yulei; Wang, Lu; Wang, Xianshi; Huang, Zhuangsong; Xu, Chengbiao; Yang, Tao; Zhao, Xiaodan; Qi, Jingyao; Ma, Jun

    2017-11-01

    Thallium (Tl) is highly toxic to mammals and relevant pollution cases are increasing world-widely. Convenient and efficient method for the removal of trace Tl from contaminated source water is imperative. Here, the removal of trace Tl by K 2 FeO 4 [Fe(VI)] was investigated for the first time, with the exploration of reaction mechanisms. Six different types of water treatment agents (powdered activated carbon, Al 2 (SO 4 ) 3 , FeCl 3 , δ-MnO 2 , MnO 2 nano-particles, and K 2 FeO 4 ) were used for the removal of Tl in spiked river water, and K 2 FeO 4 showed excellent removal performance. Over 92% of Tl (1 μg/L) was removed within 5 min by applying 2.5 mg/L of K 2 FeO 4 (pH 7.0, 20 °C). XPS analysis revealed that in the reaction of Tl(I) with K 2 FeO 4 , Tl(I) was oxidized to Tl(III), and removed by the K 2 FeO 4 reduced ferric particles. The removal of Tl by in situ formed and ex situ formed ferric particle was examined respectively, and the results revealed that the removal of trace Tl could be attributed to the combination of adsorption and coprecipitation processes. The hydrodynamic size of the reduced particle from K 2 FeO 4 ranged from 10 nm to 100 nm, and its surface was negatively charged under neutral pH condition. These factors were conducive for the efficient removal of Tl by K 2 FeO 4 . The effects of solution pH, coexisting ions (Na + , Ca 2+ , and HCO 3 - ), humic acid, solution temperature, and reductive environment on the removal and desorption of Tl were investigated, and the elimination of Tl in polluted river water and reservoir water was performed. These results suggest that K 2 FeO 4 could be an efficient and convenient agent on trace Tl removal. Copyright © 2017. Published by Elsevier Ltd.

  1. Removal of Arsenic (V) from Aqueous Solutions Using Chitosan-Red Scoria and Chitosan-Pumice Blends.

    Science.gov (United States)

    Asere, Tsegaye Girma; Mincke, Stein; De Clercq, Jeriffa; Verbeken, Kim; Tessema, Dejene A; Fufa, Fekadu; Stevens, Christian V; Du Laing, Gijs

    2017-08-09

    In different regions across the globe, elevated arsenic contents in the groundwater constitute a major health problem. In this work, a biopolymer chitosan has been blended with volcanic rocks (red scoria and pumice) for arsenic (V) removal. The effect of three blending ratios of chitosan and volcanic rocks (1:2, 1:5 and 1:10) on arsenic removal has been studied. The optimal blending ratio was 1:5 (chitosan: volcanic rocks) with maximum adsorption capacity of 0.72 mg/g and 0.71 mg/g for chitosan: red scoria (Ch-Rs) and chitosan: pumice (Ch-Pu), respectively. The experimental adsorption data fitted well a Langmuir isotherm ( R ² > 0.99) and followed pseudo-second-order kinetics. The high stability of the materials and their high arsenic (V) removal efficiency (~93%) in a wide pH range (4 to 10) are useful for real field applications. Moreover, the blends could be regenerated using 0.05 M NaOH and used for several cycles without losing their original arsenic removal efficiency. The results of the study demonstrate that chitosan-volcanic rock blends should be further explored as a potential sustainable solution for removal of arsenic (V) from water.

  2. The efficiency of macroporous polystyrene ion-exchange resins in natural organic matter removal from surface water

    Directory of Open Access Journals (Sweden)

    Urbanowska Agnieszka

    2017-01-01

    Full Text Available Natural water sources used for water treatment contains various organic and inorganic compounds. Surface waters are commonly contaminated with natural organic matter (NOM. NOM removal from water is important e.g. due to lowering the risk of disinfection by-product formation during chlorination. Ion exchange with the use of synthetic ion-exchange resins is an alternative process to typical NOM removal approach (e.g. coagulation, adsorption or oxidation as most NOM compounds have anionic character. Moreover, neutral fraction could be removed from water due to its adsorption on resin surface. In this study, applicability of two macroporous, polystyrene ion exchange resins (BD400FD and A100 in NOM removal from water was assessed including comparison of treatment efficiency in various process set-ups and conditions. Moreover, resin regeneration effectivity was determined. Obtained results shown that examined resins could be applied in NOM removal and it should be noticed that column set-up yielded better results (contrary to batch set-up. Among the examined resins A100 one possessed better properties. It was determined that increase of solution pH resulted in a slight decrease in treatment efficiency while higher temperature improved it. It was also observed that regeneration efficiency was comparable in both tested methods but batch set-up required less reagents.

  3. Improving Energy Efficiency in Industrial Solutions – Walk the Talk

    DEFF Research Database (Denmark)

    Wegener, Dieter; Finkbeiner, Matthias; Holst, Jens-Christian

    2011-01-01

    and finally communication of both environmental and economic performance of solutions to customers. One of the main tools supporting eco-design and evaluation & controlling of derived design solutions is the so called “Eco-Care-Matrix” (ECM). The ECM simply visualizes the eco-efficiency of solutions compared...... to a given baseline. In order to prevent from “green washing” criticism and to ensure “walk the talk” attitude the ECM should be scientifically well-founded using appropriate and consistent methodology. The vertical axis of an ECM illustrates the environmental performance and the horizontal axis describes...... ECM application is illustrated using the example of the Siemens MEROS® technology (Maximized Emission Reduction of Sintering) for the steel industry. MEROS® is currently the most modern and powerful system for cleaning off-gas in sinter plants. As an environmental technology MEROS® is binding...

  4. Magnetic nanoparticle (Fe3O4) impregnated onto tea waste for the removal of nickel(II) from aqueous solution

    International Nuclear Information System (INIS)

    Panneerselvam, P.; Morad, Norhashimah; Tan, Kah Aik

    2011-01-01

    The removal of Ni(II) from aqueous solution by magnetic nanoparticles prepared and impregnated onto tea waste (Fe 3 O 4 -TW) from agriculture biomass was investigated. Magnetic nanoparticles (Fe 3 O 4 ) were prepared by chemical precipitation of a Fe 2+ and Fe 3+ salts from aqueous solution by ammonia solution. These magnetic nanoparticles of the adsorbent Fe 3 O 4 were characterized by surface area (BET), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and Fourier Transform-Infrared Spectroscopy (FT-IR). The effects of various parameters, such as contact time, pH, concentration, adsorbent dosage and temperature were studied. The kinetics followed is first order in nature, and the value of rate constant was found to be 1.90 x 10 -2 min -1 at 100 mg L -1 and 303 K. Removal efficiency decreases from 99 to 87% by increasing the concentration of Ni(II) in solution from 50 to 100 mg L -1 . It was found that the adsorption of Ni(II) increases by increasing temperature from 303 to 323 K and the process is endothermic in nature. The adsorption isotherm data were fitted to Langmuir and Freundlich equation, and the Langmuir adsorption capacity, Q o , was found to be (38.3) mg g -1 . The results also revealed that nanoparticle impregnated onto tea waste from agriculture biomass, can be an attractive option for metal removal from industrial effluent.

  5. Silver removal from aqueous solution by biochar produced from biosolids via microwave pyrolysis.

    Science.gov (United States)

    Antunes, Elsa; Jacob, Mohan V; Brodie, Graham; Schneider, Philip A

    2017-12-01

    The contamination of water with silver has increased due to the widespread applications of products with silver employed as antimicrobial agent. Adsorption is a cost-effective method for silver removal from aqueous solution. In this study biochar, produced from the microwave assisted pyrolysis of biosolids, was used for silver removal from an aqueous solution. The adsorption kinetics, isotherms and thermodynamics were investigated to better understand the silver removal process by biochar. X-ray diffraction results demonstrated that silver removal was a combination two consecutive mechanisms, reduction and physical adsorption. The Langmuir model fitted the experimental data well, showing that silver removal was predominantly a surface mechanism. The thermodynamic investigation demonstrated that silver removal by biochar was an exothermic process. The final nanocomposite Ag-biochar (biochar plus silver) was used for methylene blue adsorption and photodegradation. This study showed the potential of using biochar produced from biosolids for silver removal as a promising solution to mitigate water pollution and an environmentally sustainable approach for biosolids management and re-use. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Parametric and kinetic study of adsorptive removal of dyes from aqueous solutions using an agriculture waste

    Science.gov (United States)

    Bencheikh, imane; el hajjaji, souad; abourouh, imane; Kitane, Said; Dahchour, Abdelmalek; El M'Rabet, Mohammadine

    2017-04-01

    Wastewater treatment is the subject of several studies through decades. Interest is continuously oriented to provide cheaper and efficient methods of treatment. Several methods of treatment exit including coagulation flocculation, filtration, precipitation, ozonation, ion exchange, reverse osmosis, advanced oxidation process. The use of these methods proved limited because of their high investment and operational cost. Adsorption can be an efficient low-cost process to remove pollutants from wastewater. This method of treatment calls for an solid adsorbent which constitutes the purification tool. Agricultural wastes have been widely exploited in this case .As we know the agricultural wastes are an important source of water pollution once discharged into the aquatic environment (river, sea ...). The valorization of such wastes and their use allows the prevention of this problem with an economic and environment benefits. In this context our study aimed testing the wastewater treatment capacity by adsorption onto holocellulose resulting from the valorization of an agriculture waste. In this study, methylene blue (MB) and methyl orange (MO) are selected as models pollutants for evaluating the holocellulose adsorbent capacity. The kinetics of adsorption is performed using UV-visible spectroscopy. In order to study the effect of the main parameters for the adsorption process and their mutual interaction, a full factorial design (type nk) has been used.23 full factorial design analysis was performed to screen the parameters affecting dye removal efficiency. Using the experimental results, a linear mathematical model representing the influence of the different parameters and their interactions was obtained. The parametric study showed that efficiency of the adsorption system (Dyes/ Holocellulose) is mainly linked to pH variation. The best yields were observed for MB at pH=10 and for MO at pH=2.The kinetic data was analyzed using different models , namely , the pseudo

  7. Removal of lindane from an aqueous solution by using aminopropyl silica gel-immobilized calix[6]arene.

    Science.gov (United States)

    Tor, Ali; Aydin, Mehmet Emin; Aydin, Senar; Tabakci, Mustafa; Beduk, Fatma

    2013-11-15

    An aminopropyl silica gel-immobilized calix[6]arene (C[6]APS) has been used for the removal of lindane from an aqueous solution in batch sorption technique. The C[6]APS was synthesized with p-tert-butylcalix[6]arene hexacarboxylate derivative and aminopropyl silica gel in the presence of N,N'-diisopropyl carbodiimide coupling reagent. The sorption study was carried out as functions of solution pH, contact time, initial lindane concentration, C[6]APS dosage and ionic strength of solution. The matrix effect of natural water samples on the sorption efficiency of C[6]APS was also investigated. Maximum lindane removal was obtained at a wide pH range of 2-8 and sorption equilibrium was achieved in 2h. The isotherm analysis indicated that the sorption data can be represented by both Langmuir and Freundlich isotherm models. Increasing ionic strength of the solutions increased the sorption efficiency and matrix of natural water samples had no effect on the sorption of lindane. By using multilinear regression model, regression equation was also developed to explain the effects of the experimental variables. Copyright © 2013 Elsevier B.V. All rights reserved.

  8. A novel compound cleaning solution for benzotriazole removal after copper CMP

    International Nuclear Information System (INIS)

    Gu Zhangbing; Liu Yuling; Gao Baohong; Wang Chenwei; Deng Haiwen

    2015-01-01

    After the chemical mechanical planarization (CMP) process, the copper surface is contaminated by a mass of particles (e.g. silica) and organic residues (e.g. benzotriazole), which could do great harm to the integrated circuit, so post-CMP cleaning is essential. In particular, benzotriazole (BTA) forms a layer of Cu-BTA film with copper on the surface, which leads to a hydrophobic surface of copper. So an effective cleaning solution is needed to remove BTA from the copper surface. In this work, a new compound cleaning solution is designed to solve two major problems caused by BTA: one is removing BTA and the other is copper surface corrosion that is caused by the cleaning solution. The cleaning solution is formed of alkaline chelating agent (FA/O II type), which is used to remove BTA, and a surfactant (FA/O I type), which is used as a corrosion inhibitor. BTA removal is characterized by contact angle measurements and electrochemical techniques. The inhibiting corrosion ability of the surfactant is also characterized by electrochemical techniques. The proposed compound cleaning solution shows advantages in removing BTA without corroding the copper surface. (paper)

  9. Experimental study of iodine removal efficiency in self-priming venturi scrubber

    International Nuclear Information System (INIS)

    Gulhane, N.P.; Landge, A.D.; Shukla, D.S.; Kale, S.S.

    2015-01-01

    Highlights: • Fabrication, erection of experimental set up and carrying out experimentation with self priming venturi scrubber. • Predicting solubility of iodine in water and its pH dependency. • Increasing pH of water increases iodine removal efficiency. • Maximum iodine removal efficiency is obtained at 10 pH of water using sodium thiosulphate. - Abstract: The objective of present experimental study is to examine the iodine removal efficiency of a self-priming venturi scrubber for submerged operating condition. The venturi scrubber is used in Containment Filtered Venting System of nuclear power plants to remove the gaseous pollutants from contaminated gas during severe accidents. The experiment consists of mixing the iodine vapours with the air using suction venturi and pressure cooker system. The purpose of iodine mixing with air is to examine scrubbing performance of the designed venturi scrubber with water as scrubbing liquid. The performance parameters of venturi scrubber are expressed mainly in terms of pressure drop and iodine removal efficiency. The iodine removal efficiency of venturi scrubber is estimated for a series of two experiments by measuring the quantity of iodine in water from iodometric titration with four distinct pH of water. It has been experimentally observed that iodine removal efficiency is improved by using higher pH value of scrubbing liquid since solubility of iodine gets improved at higher pH

  10. Efficiency of Acacia Tortillis Plant Pod Shell as a Low Cost and Available Adsorbent for the Removal of Phenol

    Directory of Open Access Journals (Sweden)

    Hossien JafariMansoorian

    2015-05-01

    Full Text Available The presence of nondegradable toxic compounds such as phenol in the environment has nowadays led to many health and environmental problems. The present empirical study was conducted on the lab scale to evaluate the efficiency of Acacia tortillis pod shell as a new alternative and low cost adsorbent for removing phenol from aqueous solutions. The experiment was performed in a batch system and the effects of important operation variables including initial phenol concentrations of 0.5, 1, 2, 4, 8, 16, 32, and 64 mg/l, absorbent doses of 0.1, 0.2, 0.4, 0.8, and 1.6g/l in predetermined mesh sizes (ranging over 30-60 and 60-100, pH levels of 2, 4, 6, 8, 10, and 12, and contact times of 10, 20, 30, 40, 50, and 60 min were evaluated. Finally, the Freundlich and Langmuir adsorption isotherms were determined in order to describe the relationship between the colored solution and the absorbent. Results showed that the highest phenol absorption efficiency achieved was above 95% which was obtained with an optimum pH level of 2, an optimum absorbent dose of 0.2 g/l, and a mesh size of 60-100 for a contact time of 10 minutes and at a low pollutant concentration. Increasing phenol concentration increased its removal efficiency but this removal rate was lower at extreme concentrations. Also, the adsorption process was found to be more compatible with the Freundlich model. Based on the results obtained, the pod shells of Acacia tortillis pod shell may be claimed to be an effective, efficient, and cheap absorbent for the removal of phenol from aqueous solutions.

  11. Aquatic environmental monitoring and removal efficiency of detergents

    Directory of Open Access Journals (Sweden)

    Hanan S. Abd El-Gawad

    2014-10-01

    The results showed wide variations observed between surface (0.07–0.38 mg LAS/l and bottom water (0.05–0.17 mg LAS/l due to increase in population density and human activities that recorded highest concentration along rural area (surface: 1.24–2.45 and bottom: 0.93–1.083 mg LAS/l. Low concentration of surfactants was found in drinking water (0.005–0.007 mg LAS/l compared to the concentration of the corresponding water samples along the River Nile. In conclusion, the study indicated that the treatment processes for drinking water production were insufficient for the complete removal of surfactants and adsorption process by using zeolite as low cost, most beneficial, economically feasible method as well as easy to operate for producing high quality of water.

  12. Removal of Reactive Dyes (Green, Orange, and Yellow from Aqueous Solutions by Peanut Shell Powder as a Natural Adsorbent

    Directory of Open Access Journals (Sweden)

    Hosein Nadi

    2012-11-01

    Full Text Available Please cite this article as: Nadi H, Alizadeh M, Ahmadabadi M, Yari AR, Hashemi S. Removal of Reactive Dyes (Green, Orange, and Yellow from Aqueous Solutions by Peanut Shell Powder as a Natural Adsorbent. Arch Hyg Sci 2012;1(2:41-7. Abstract: Background & Aims of the Study: Textile dyes generally are made of synthetic, organic, and aromatic compounds that may be contain of some heavy metals in their structure. Complex structure and presence of these metals cause toxicity and may be mutagen, teratogen or carcinogen. This study has investigated the ability of peanut shell powder to removal of some reactive dyes (Green 19, Orange 16, and Yellow 14 from aqueous solutions. Materials & Methods : The effects of contact time, initial concentration of reactive dyes, adsorbent dosage and pH have been reported. The applicability of Langmuir and Freundlich isotherm was tried for the system to completely understand the adsorption isotherm processes. Results: Batch adsorption studies showed that the peanut shell powder was able to remove the reactive dyes from aqueous solutions in the concentration range 25 to 250 mg/L. The highest percent removal for the Green 19, Orange 16, and Yellow 14 dyes was 84.2%, 87.36% and 88.49%, respectively. The adsorption was favored with maximum adsorption at pH=2. Also the optimum adsorbent dose was obtained 0.4 g/100 mL. By increasing adsorbent dose and initial concentration, removal efficiency was increased considerably. The adsorption isotherm studies clearly indicated that the adsorptive behavior of dyes on peanut shell satisfies only the Freundlich with average R 2 =0.926. Conclusions: Based on findings, the peanut shell powder was found as a low cost, natural and abundant availability adsorbent to removal of reactive dyes from aqueous solution. References: 1. García-Montaño J, Torrades F, García-Hortal JA, Domènec X, Peral J. Combining photo-Fenton process with aerobic sequencing batch reactor for commercial hetero

  13. Bioadsorber efficiency, design, and performance forecasting for alachlor removal.

    Science.gov (United States)

    Badriyha, Badri N; Ravindran, Varadarajan; Den, Walter; Pirbazari, Massoud

    2003-10-01

    This study discusses a mathematical modeling and design protocol for bioactive granular activated carbon (GAC) adsorbers employed for purification of drinking water contaminated by chlorinated pesticides, exemplified by alachlor. A thin biofilm model is discussed that incorporates the following phenomenological aspects: film transfer from the bulk fluid to the adsorbent particles, diffusion through the biofilm immobilized on adsorbent surface, adsorption of the contaminant into the adsorbent particle. The modeling approach involved independent laboratory-scale experiments to determine the model input parameters. These experiments included adsorption isotherm studies, adsorption rate studies, and biokinetic studies. Bioactive expanded-bed adsorber experiments were conducted to obtain realistic experimental data for determining the ability of the model for predicting adsorber dynamics under different operating conditions. The model equations were solved using a computationally efficient hybrid numerical technique combining orthogonal collocation and finite difference methods. The model provided accurate predictions of adsorber dynamics for bioactive and non-bioactive scenarios. Sensitivity analyses demonstrated the significance of various model parameters, and focussed on enhancement in certain key parameters to improve the overall process efficiency. Scale-up simulation studies for bioactive and non-bioactive adsorbers provided comparisons between their performances, and illustrated the advantages of bioregeneration for enhancing their effective service life spans. Isolation of microbial species revealed that fungal strains were more efficient than bacterial strains in metabolizing alachlor. Microbial degradation pathways for alachlor were proposed and confirmed by the detection of biotransformation metabolites and byproducts using gas chromatography/mass spectrometry.

  14. Functional clay supported bimetallic nZVI/Pd nanoparticles used for removal of methyl orange from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Ting [School of Environmental Science and Engineering, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Fujian Key Laboratory of Pollution Control and Resource Reuse, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Su, Jin [School of Environmental Science and Engineering, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Jin, Xiaoying [School of Environmental Science and Engineering, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Fujian Key Laboratory of Pollution Control and Resource Reuse, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Chen, Zuliang, E-mail: Zuliang.chen@unisa.edu.au [School of Environmental Science and Engineering, Fujian Normal University, Fuzhou 350007, Fujian Province (China); Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes, SA 5095 (Australia); Megharaj, Mallavarapu; Naidu, Ravendra [Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes, SA 5095 (Australia)

    2013-11-15

    Highlights: • Functional clay supported bimetallic nZVI/Pd was synthesized. • Methyl orange (MO) was degraded using B-nZVI/Pd. • 93.75% of MO in wastewater was removed. • The functions of clay, nZVI and Pd were observed. -- Abstract: Bentonite supported Fe/Pd nanoparticles (B/nZVI/Pd) were synthesized as composites that exhibit functionalities assisting in the removal of methyl orange (MO) from aqueous solution. The results showed that 91.87% of MO was removed using B/nZVI/Pd, while only 85% and 1.41% of MO were removed using nZVI/Pd and bentonite after 10 min, respectively. The new findings include that the presence of bentonite decreased the aggregation of nZVI/Pd and nZVI in the composite played its role as a reductant, while Pd{sup 0} acted as the catalyst to enhance the degradation of MO, which were confirmed by scanning electron microscopy (SEM), X-ray diffraction (XRD), UV–vis analysis and the batch experiments. The increase in B/nZVI/Pd loading led to greater removal efficiency, while decolorization efficiency declined in the presence of anions such as nitrate, sulfite and carbonate, especially nitrate, which decreased the apparent rate constant k{sub obs} almost 17.06-fold. The kinetics study indicated that the degradation of MO fitted well to the pseudo-first-order model, where the k{sub obs} was 0.0721 min{sup −1}. Finally, the reactivity of aged B/nZVI/Pd was investigated, and the application of B/nZVI/Pd in wastewater indicated a removal efficiency higher than 93.75%. This provided a new environmental pollution management option for dyes-contaminated sites.

  15. Synthesis of hydroxyapatite/multi-walled carbon nanotubes for the removal of fluoride ions from solution

    International Nuclear Information System (INIS)

    Ruan, Zhongyuan; Tian, Yaxi; Ruan, Jifu; Cui, Guijia; Iqbal, Kanwal; Iqbal, Anam; Ye, Herui; Yang, Zhangzhong; Yan, Shiqiang

    2017-01-01

    Graphical abstract: Hydroxyapatite nucleated and grown on Multi-walled carbon nanotubes (HA-MWCNTs) showed enhanced fluoride removal performance. - Highlights: • Noval HA nanoparticles and HA-MWCNTs composites were successfully synthesized for the first time. • The synthesized HA-MWCNTs composites exhibited a higher defluoridation capacity of 39.22 mg g"−"1. • It could reduced the fluoride concentration of the real waste water from 8.79 mg L"−"1 to approximately 0.25 mg L"−"1. - Abstract: A novel composite material, hydroxyapatite (HA)-multi-walled carbon nanotubes (MWCNTs), was prepared using a simple in-situ sol-gel method, and was used for the first time to remove fluoride from water. The novel HA-MWCNTs were characterized using TEM, FT-IR, BET and XRD analysis. The TEM and SAED results revealed that the MWCNTs were uniformly encapsulated by hydroxyapatite nanoparticles. The synthesized HA-MWCNTs had a high specific surface area (180.504 m"2 g"−"1), with an average pore width (14.607 nm) and pore volume (0.774 cm"3 g"−"1), which produced a defluoridation capacity (DC) of 30.22 mgF"− g"−"1. This value was greater than unmodified hydroxyapatite (HA), which exhibited a larger specific surface area (172.233 m"2 g"−"1) and an excellent DC of 17.80 mgF"− g"−"1. A number of pertinent parameters that could affect the defluoridation performance of the HA/MWCNTs including weight ratios of the two key materials, solution pH and competing anions were carefully and comprehensively examined. It was found that the adsorption results followed the Langmuir and Freundlich isotherm model, and the sorption kinetics of the F"− appeared to exhibit a pseudo second order. Moreover, the adsorption reaction was spontaneous and endothermic and appeared to exhibit a higher initial adsorption rate. This reaction appeared to occur result from both anion exchange and electrostatic interactions. When the HA-MWCNTs (MH6) were at an adsorbent dose of 2.0 g L"−"1

  16. Synthesis of hydroxyapatite/multi-walled carbon nanotubes for the removal of fluoride ions from solution

    Energy Technology Data Exchange (ETDEWEB)

    Ruan, Zhongyuan; Tian, Yaxi [College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000 (China); Ruan, Jifu [Chemistry Teaching and Research Group, No.1 Middle School of Queshan, Henan 463200 (China); Cui, Guijia; Iqbal, Kanwal; Iqbal, Anam [College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000 (China); Ye, Herui; Yang, Zhangzhong [Northwest Regional Office of Nuclear and Radiation Safety, Ministry of Environmental Protection, Lanzhou 730000 (China); Yan, Shiqiang, E-mail: yansq@lzu.edu.cn [College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000 (China)

    2017-08-01

    Graphical abstract: Hydroxyapatite nucleated and grown on Multi-walled carbon nanotubes (HA-MWCNTs) showed enhanced fluoride removal performance. - Highlights: • Noval HA nanoparticles and HA-MWCNTs composites were successfully synthesized for the first time. • The synthesized HA-MWCNTs composites exhibited a higher defluoridation capacity of 39.22 mg g{sup −1}. • It could reduced the fluoride concentration of the real waste water from 8.79 mg L{sup −1} to approximately 0.25 mg L{sup −1}. - Abstract: A novel composite material, hydroxyapatite (HA)-multi-walled carbon nanotubes (MWCNTs), was prepared using a simple in-situ sol-gel method, and was used for the first time to remove fluoride from water. The novel HA-MWCNTs were characterized using TEM, FT-IR, BET and XRD analysis. The TEM and SAED results revealed that the MWCNTs were uniformly encapsulated by hydroxyapatite nanoparticles. The synthesized HA-MWCNTs had a high specific surface area (180.504 m{sup 2} g{sup −1}), with an average pore width (14.607 nm) and pore volume (0.774 cm{sup 3} g{sup −1}), which produced a defluoridation capacity (DC) of 30.22 mgF{sup −} g{sup −1}. This value was greater than unmodified hydroxyapatite (HA), which exhibited a larger specific surface area (172.233 m{sup 2} g{sup −1}) and an excellent DC of 17.80 mgF{sup −} g{sup −1}. A number of pertinent parameters that could affect the defluoridation performance of the HA/MWCNTs including weight ratios of the two key materials, solution pH and competing anions were carefully and comprehensively examined. It was found that the adsorption results followed the Langmuir and Freundlich isotherm model, and the sorption kinetics of the F{sup −} appeared to exhibit a pseudo second order. Moreover, the adsorption reaction was spontaneous and endothermic and appeared to exhibit a higher initial adsorption rate. This reaction appeared to occur result from both anion exchange and electrostatic interactions. When the

  17. Investigation of combined coagulation and advanced oxidation process efficiency for the removal of Clarithromycin from wastewater

    Directory of Open Access Journals (Sweden)

    ahmad reza Yazdanbakhsh

    2011-06-01

    Conclusion: In general the results of the performed tests indicated that combined coagulation and advanced oxidation process has high efficiency in removal of Claritromycin wastewater COD. But application this method in the industry should be surveyed.

  18. Highly Efficient Closed-Loop CO2 Removal System for Deep-Space ECLSS, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — TDA Research Inc.(TDA) in collaboration with University of Puerto Rico ? Mayaguez (UPRM is proposing to develop a highly efficient CO2 removal system based on UPRM...

  19. Highly efficient removal of arsenic metal ions with high superficial area hollow magnetite nanoparticles synthetized by AACVD method

    Energy Technology Data Exchange (ETDEWEB)

    Monárrez-Cordero, B.; Amézaga-Madrid, P.; Antúnez-Flores, W.; Leyva-Porras, C.; Pizá-Ruiz, P. [Centro de Investigación en Materiales Avanzados S.C., and Laboratorio Nacional de Nanotecnología, Miguel de Cervantes 120, Chihuahua, Chih. C.P. 31109 (Mexico); Miki-Yoshida, M., E-mail: mario.miki@cimav.edu.mx [Centro de Investigación en Materiales Avanzados S.C., and Laboratorio Nacional de Nanotecnología, Miguel de Cervantes 120, Chihuahua, Chih. C.P. 31109 (Mexico)

    2014-02-15

    Highlights: ► Fast and high arsenic removal efficiency, almost 100% in one minute. ► Successful synthesis of high purity magnetite hollow nanoparticles is reported. ► They were synthesized by one step aerosol assisted CVD technique. ► Detailed microstructural characterization by electron microscopy was performed. -- Abstract: New nanotechnology alternatives and methodologies have been developed in order to overcome the limitations of conventional techniques for metal ions removal from water. Currently, the removal of heavy metals requires multiple steps which include the separation and post-treatment of the generated sludge. Usually, this sludge is composed of dangerous environmental pollutants mixed with the material used for removing the metal ion. Thus, the removal of these metals becomes a challenging task. Herein we report the synthesis of magnetite nanoparticles with high specific area by the aerosol assisted chemical vapour deposition method. Deposition temperature were fixed at 450 °C and a mixture of Ar–air were used as a carrier gas, a flow of 1.0 and 0.015 L min{sup −1} were used for Ar and air, respectively. The precursor solution was a dilution of Fe (II) chloride in methanol, with different concentration 0.01, 0.05 and 0.1 mol dm{sup −3}. The crystalline structure of the nanoparticles was characterized by grazing incidence X-ray diffraction. Morphology and microstructure were analyzed by field emission scanning electron microscopy, scanning probe microscopy and transmission electron microscopy. Magnetic properties were evaluated with a vibrating sample magnetometer and specific area was measured by the Brunauer–Emmett–Teller method. To determine the removal efficiency of arsenic ion from water, several tests were carried out at six exposition times 1, 3, 5, 10, 20 and 30 min. Results showed high removal efficiency, more than 99%, in less than 1 min.

  20. Swift adsorptive removal of Congo red from aqueous solution by K1.33Mn8O16 nanowires.

    Science.gov (United States)

    Wu, Junshu; Li, Hongyi; Wang, Jinshu; Li, Zhifei

    2013-08-01

    A swift and efficient approach to converting organic dye effluents into fresh water could be of substantial benefit. In this study, we presented facile hydrothermal synthesis of K1.33Mn8O16 nanowires in ammonium fluoride (NH4F) aqueous solution. The crystallization process of K1.33Mn8O16 nanowires was investigated. The as-obtained K1.33Mn8O16 nanowires were used for swift adsorptive removal of Congo red from aqueous solution without adjusting pH value at room temperature. Adsorption kinetic experimental data are well described by pseudo-second-order rate kinetic model, and the adsorption isotherm fits Langmuir isotherm model. The present investigation provides an efficient approach to designing and fabricating manganese-based nanomaterials for environmental remediation.

  1. Influences of impurities on iodine removal efficiency of silver alumina adsorbent

    Energy Technology Data Exchange (ETDEWEB)

    Fukasawa, Tetsuo; Funabashi, Kiyomi [Hitachi, Ltd., Ibaraki (Japan); Kondo, Yoshikazu [Hitachi, Ltd., Ibaraki (Japan)

    1997-08-01

    Silver impregnated alumina adsorbent (AgA), which was developed for iodine removal from off-gas of nuclear power and reprocessing plants has been tested laying emphasis on investigation of the influences gaseous impurities have on adsorbent chemical stability and iodine removal efficiency. The influences of the major impurities such as nitrogen oxides and water vapor were checked on the chemical state of impregnated silver compound (AgNO{sub 3}) and decontamination factor (DF) value. At 150{degrees}C, a forced air flow with 1.5% nitrogen oxide (NO/NO{sub 2}=1/1) reduced silver nitrate to metallic silver, whereas pure air and air with 1.5% NO{sub 2} had no effect on the chemical state of silver. Metallic silver showed a lower DF value for methyl iodide in pure air (without impurities) than silver nitrate and the lower DF of metallic silver was improved when impurities were added. At 40{degrees}C, a forced air flow with 1.5% nitrogen dioxide (NO{sub 2}) increased the AgA weight by about 20%, which was caused by the adsorption of nitric acid solution on the AgA surface. AgA with l0wt% silver showed higher weight increase than that with 24wt% silver which had lower porosity. Adsorption of acid solution lowered the DF value, which would be due to the hindrance of contact between methyl iodide and silver. The influences of other gaseous impurities were also investigated and AgA showed superior characteristics at high temperatures. 14 refs., 11 figs.

  2. Chlorite alteration in aqueous solutions and uranium removal by altered chlorite

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Eungyeong; Ahn, Hyangsig [Department of Earth and Environmental Sciences, Korea University, Anam-dong, Seongbuk-gu, Seoul 02841 (Korea, Republic of); Jo, Ho Young, E-mail: hyjo@korea.ac.kr [Department of Earth and Environmental Sciences, Korea University, Anam-dong, Seongbuk-gu, Seoul 02841 (Korea, Republic of); Ryu, Ji-Hun; Koh, Yong-Kwon [Korea Atomic Energy Research Institute, 1045 Daedeokdaero, Yuseong-gu, Daejeon 34057 (Korea, Republic of)

    2017-04-05

    Highlights: • Chlorite alteration and the U removal capacity of altered chlorite were investigated. • Initial pH affected more chlorite dissolution than ionic strength. • Chlorite dissolution at pH{sub o} = 3–8 was inversely proportional to the U removal capacity. • Chlorite dissolution at pH{sub o} = 10 was proportional to the U removal capacity. • The formation of Fe-containing secondary minerals affected the U removal capacity. - Abstract: Chlorite alteration and the U removal capacity of altered chlorite were investigated. Batch kinetic dissolution tests using clinochlore CCa-2 were conducted for 60 days in aqueous solutions of various pHs and ionic strengths. Batch sorption tests using these altered chlorite samples were conducted for 48 h with natural groundwater containing 3.06 × 10{sup −6} M U. Chlorite dissolution was influenced more by pH{sub o} than by the ionic strength of the solution. TEM analysis revealed Fe(oxy)hydroxide aggregates in the solid residue from the batch dissolution test with 0.1 M NaClO{sub 4} solution at pH{sub o} = 10. The U removal capacity of the reacted chlorite samples at pH{sub o} = 6–10 was higher than that of the reacted chlorite samples at pH{sub o} = 3. The degree of dissolution of chlorite samples reacted at pH{sub o} = 3–8 was inversely proportional to the U removal capacity, but that of chlorite samples reacted at pH{sub o} = 10 was proportional to the U removal capacity. The positive correlation between the U removal capacity and degree of chlorite dissolution at pH{sub o} = 10 might be due to the formation of Fe-containing secondary minerals and changes in the reactive sites.

  3. 2-Chlorophenol Removal of Aqueous Solution Using Advanced Oxidation Processes Resulting from Iron/ Persulfate and Ultra Violet/ Persulfate

    Directory of Open Access Journals (Sweden)

    Shokufeh Astereki

    2016-06-01

    Full Text Available Background: Advanced oxidation processes are used to remove toxic aromatic compounds with low biodegradability, such as 2-chlorophenol. This study investigated the use of sulfate (SO4- and persulfate (S2O82- radicals, as one of the advanced oxidation methods, to remove 2- chlorophenol from aquatic solutions. Methods: This experimental and pilot-scale study was carried out using two chemical batch reactors; one of the reactors equipped with UV lamps and the other was on the hot plate. In iron/ persulfate (Fe/S2O82- and ultra violet/ persulfate (UV/S2O82- processes different parameters were investigated. Results: Iron, UV, the initial pH of the solution, persulfate concentration have considerable effects on the elimination of 2-chlorophenol in both processes. In both processes, the maximum elimination occurred in acidic conditions. The elimination efficiency was increased by increasing the concentration of 2-chlorophenol and UV intensity, and also by decreasing the concentration of persulfate and iron. Accordingly, in iron/ persulfate and ultra violet/ persulfate processes 2-chlorophenol was eliminated with 99.96% and 99.58% efficiencies, respectively. Conclusion: Sulfate radicals produced from activated persulfate ions with hot-Fe ion and UV radiation have significant impact on the removal of 2-chlorophenol. Therefore, the processes of Fe/S2O82- and UV/S2O82- can be regarded as good choices for industrial wastewater treatment plants operators in the future.

  4. Cadmium hydroxide nanowire loaded on activated carbon as efficient adsorbent for removal of Bromocresol Green

    Science.gov (United States)

    Ghaedi, Mehrorang; Khajesharifi, Habibollah; Hemmati Yadkuri, Amin; Roosta, Mostafa; Sahraei, Reza; Daneshfar, Ali

    2012-02-01

    In the present research, cadmium hydroxide nanowire loaded on activated carbon (Cd(OH) 2-NW-AC) was synthesized and characterized. This new adsorbent was applied for the removal of Bromocresol Green (BCG) molecules from aqueous solutions. The influence of effective variables such as solution pH, contact time, initial BCG concentration, amount of Cd(OH) 2-NW-AC and temperature on the adsorption efficiency of BCG in batch system was examined. During all experiments BCG contents were determined by UV-Vis spectrophotometer. Fitting the experimental data to different kinetic models including pseudo-first-order, pseudo-second-order, Elovich and intra-particle diffusion kinetic models show the suitability of the pseudo-second-order kinetic model to interpret in the experimental data. Equilibrium isotherm studies were examined by application of different conventional models such as Langmuir, Freundlich and Tempkin models to explain the experimental data. Based on considering R2 value as criterion the adsorption data well fitted to Langmuir model with maximum adsorption capacity of 108.7 mg g -1. Thermodynamic parameters (Gibb's free energy, entropy and enthalpy) of adsorption were calculated according to general procedure to take some information about the on-going adsorption process. The high negative value of Gibb's free energy and positive value of enthalpy show the feasibility and endothermic nature of adsorption process.

  5. Micelle swelling agent derived cavities for increasing hydrophobic organic compound removal efficiency by mesoporous micelle@silica hybrid materials

    KAUST Repository

    Shi, Yifeng

    2012-06-01

    Mesoporous micelle@silica hybrid materials with 2D hexagonal mesostructures were synthesized as reusable sorbents for hydrophobic organic compounds (HOCs) removal by a facile one-step aqueous solution synthesis using 3-(trimethoxysily)propyl-octadecyldimethyl-ammonium chloride (TPODAC) as a structure directing agent. The mesopores were generated by adding micelle swelling agent, 1,3,5-trimethyl benzene, during the synthesis and removing it afterward, which was demonstrated to greatly increase the HOC removal efficiency. In this material, TPODAC surfactant is directly anchored on the pore surface of mesoporous silica via SiOSi covalent bond after the synthesis due to its reactive Si(OCH 3) 3 head group, and thus makes the synthesized materials can be easily regenerated for reuse. The obtained materials show great potential in water treatment as pollutants sorbents. © 2011 Elsevier Inc. All rights reserved.

  6. Removal of Hg(II) from aqueous solution using sodium humate as heavy metal capturing agent.

    Science.gov (United States)

    Wang, Shixiang; Liu, Yong; Fan, Qin; Zhou, Anlan; Fan, Lu; Mu, Yulan

    2016-12-01

    An environmental friendly and economic natural biopolymer-sodium humate (HA-Na) was used to capture Hg(II) from aqueous solutions, and the trapped Hg(II) (HA-Na-Hg) was then removed by aluminium coagulation. The best Hg(II) capturing performance (90.60%) was observed under the following conditions: initial pH of 7.0, coagulation pH of 6.0, HA-Na dosage of 5.0 g L -1 , Al 2 (SO 4 ) 3 .18H 2 O dosage of 4.0 g L -1 , initial Hg(II) concentration of 50 mg L -1 and capturing time of 30 min. The HA-Na compositions with the molecular weight beyond 70 kDa showed the most intense affinity toward Hg(II). The results showed that the reaction equilibrium was achieved within 10 min (pH 7.0), and could be well fitted by the pseudo-second-order kinetics model. The capturing process could be well described by the Langmuir isotherm model and the maximum capturing capacity of Hg(II) was high up to 9.80 mg g -1 at 298 K (pH 7.0). The Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) analysis showed that the redox reaction between Hg(II) and HA-Na and the coordination reaction of carboxyl and hydroxy groups of HA-Na with Hg(II) were responsible for Hg(II) removal. The successive regeneration experiment showed that the capturing efficiency of humates for Hg(II) was maintained at about 51% after five capture-regeneration recycles.

  7. Removal of radioactive cesium from soil by ammonium citrate solution and ionic liquid

    International Nuclear Information System (INIS)

    Ishiwata, Shunji; Kitakouji, Manabu; Taga, Atsushi; Ogata, Fumihiko; Ouchi, Hidekazu; Yamanishi, Hirokuni; Inagaki, Masayo

    2015-01-01

    Radioactive cesium has strongly bound soil as time proceeded, which could not be cleaved in mild condition. We have found that serial treatment of ammonium citrate solution and ionic liquid removed radioactive cesium from soil effectively. The sequence of the treatment is crucial, since inverse serial treatment or mixture of two kinds of solution did not show such an effect, which suggested that ammonium citrate unlocked trapped cesium in soil and ionic liquid solved it. We also found that repeating serial treatment and prolonged treatment time additively removed cesium from soil. (author)

  8. removal of hazardous pollutants from industrial waste solutions using membrane techniques

    International Nuclear Information System (INIS)

    Selim, Y.T.M.

    2001-01-01

    the removal of hazardous pollutants from industrial waste solutions is of essential demand field for both scientific and industrial work. the present work includes detailed studies on the possible use of membrane technology especially liquid emulsion membrane for the removal of hazardous pollutants such as; cadmium , cobalt , lead, copper and uranium from different industrial waste solution . this research can be applied for mixed waste problems. the work carried out in this thesis is presented in three main chapters, namely introduction, experimental and results and discussion

  9. Valorization of aquaculture waste in removal of cadmium from aqueous solution: optimization by kinetics and ANN analysis

    Science.gov (United States)

    Aditya, Gautam; Hossain, Asif

    2018-05-01

    Cadmium is one of the most hazardous heavy metal concerning human health and aquatic pollution. The removal of cadmium through biosorption is a feasible option for restoration of the ecosystem health of the contaminated freshwater ecosystems. In compliance with this proposition and considering the efficiency of calcium carbonate as biosorbent, the shell dust of the economically important snail Bellamya bengalensis was tested for the removal of cadmium from aqueous medium. Following use of the flesh as a cheap source of protein, the shells of B. bengalensis made up of CaCO3 are discarded as aquaculture waste. The biosorption was assessed through batch sorption studies along with studies to characterize the morphology and surface structures of waste shell dust. The data on the biosorption were subjected to the artificial neural network (ANN) model for optimization of the process. The biosorption process changed as functions of pH of the solution, concentration of heavy metal, biomass of the adsorbent and time of exposure. The kinetic process was well represented by pseudo second order ( R 2 = 0.998), and Langmuir equilibrium ( R 2 = 0.995) had better fits in the equilibrium process with 30.33 mg g-1 of maximum sorption capacity. The regression equation ( R 2 = 0.948) in the ANN model supports predicted values of Cd removal satisfactorily. The normalized importance analysis in ANN predicts Cd2+ concentration, and pH has the most influence in removal than biomass dose and time. The SEM and EDX studies show clear peaks for Cd confirming the biosorption process while the FTIR study depicts the main functional groups (-OH, C-H, C=O, C=C) responsible for the biosorption process. The study indicated that the waste shell dust can be used as an efficient, low cost, environment friendly, sustainable adsorbent for the removal of cadmium from aqueous solution.

  10. Removal of Cadmium and Lead from Aqueous Solution by Hydroxyapatite/Chitosan Hybrid Fibrous Sorbent: Kinetics and Equilibrium Studies

    Directory of Open Access Journals (Sweden)

    Soyeon Park

    2015-01-01

    Full Text Available Hydroxyapatite (HAp/chitosan composites were prepared by a coprecipitation method, dropping a mixture of chitosan solution and phosphoric acid solution into a calcium hydroxide solution. Using the HAp/chitosan composites prepared, HAp/chitosan hybrid fibers with various HAp contents were prepared by a wet spinning method. X-ray diffraction and scanning electron microscopy analyses revealed that HAp particles were coated onto the surface of the fiber, and the surface roughness increased with increasing the HAp contents in the fiber. In order to evaluate the heavy metal removal characteristics of the HAp/chitosan hybrid fiber, adsorption tests were conducted and the results were compared with those of bare chitosan fibers. The results showed better performance in heavy metal ion removal for the HAp/chitosan hybrid fiber than the chitosan fiber. As the HAp content in the hybrid fiber increased, the removal efficiency of heavy metal ions also increased due to the increase of the specific surface area of the HAp/chitosan hybrid fiber. Adsorption kinetic and isotherm tests revealed that Pb2+ and Cd2+ adsorption to the hybrid fiber follows pseudo-second-order kinetic and Langmuir-type adsorption, respectively.

  11. Removal of Dye (Blue 56 From Aqueous Solution via Adsorption onto Pistachio Shell: kinetic and isotherm study of removal process

    Directory of Open Access Journals (Sweden)

    A. Ravanpaykar

    2012-03-01

    Full Text Available In the present investigation, shells of pistachio are used as adsorbents and they have been successfully used for the removal of Blue 56, from water samples. The effect of various parameters such as: pH, amounts of adsorbents, size of adsorbent particles and contact time on removal processing were investigated. Inthisstudy Freundlichabsorptionisotherms and Langmuir were investigated. The experimental data were correlated reasonably well by the Freundlich adsorption isotherm and isotherm parameters were calculated. In order to investigate the efficiency of Blue 56 adsorption on the pistachio shell, pseudo-first-order, pseudo-second-order, Elovich and intra-particle diffusion kinetic models were studied. Themodel that hadgoodcorrelationtoattractFreundlichwas chosenasthemodel. Its kineticsfollowsthepseudosecond order reaction.

  12. Chlorobenzene removal efficiencies and removal processes in a pilot-scale constructed wetland treating contaminated groundwater

    DEFF Research Database (Denmark)

    Braeckevelt, M.; Reiche, N.; Trapp, Stefan

    2011-01-01

    Low-chlorinated benzenes (CBs) are widespread groundwater contaminants and often threaten to contaminate surface waters. Constructed wetlands (CWs) in river floodplains are a promising technology for protecting sensitive surface water bodies from the impact of CBs. The efficiency and seasonal var...

  13. A comparative study of the removal of trivalent chromium from aqueous solutions by bentonite and expanded perlite

    International Nuclear Information System (INIS)

    Chakir, Achraf; Bessiere, Jacques; Kacemi, Kacem EL.; Marouf, Bouchaieb

    2002-01-01

    Local bentonite and expanded perlite (Morocco) have been characterised and used for the removal of trivalent chromium from aqueous solutions. The kinetic study had showed that the uptake of Cr(III) by bentonite is very rapid compared to expanded perlite. To calculate the sorption capacities of the two sorbents, at different pH, the experimental data points have been fitted to the Freundlich and Langmuir models, respectively, for bentonite and expanded perlite. For both sorbents the sorption capacity increases with increasing the pH of the suspensions. The removal efficiency has been calculated for both sorbents resulting that bentonite (96% of Cr(III) was removed) is more effective in removing trivalent chromium from aqueous solution than expanded perlite (40% of Cr(III) was removed). In the absence of Cr(III) ions, both bentonite and expanded perlite samples yield negative zeta potential in the pH range of 2-11. The changes of expanded perlite charge, from negative to positive, observed after contact with trivalent chromium(III) solutions was related to Cr(III) sorption on the surface of the solid. Thus, it was concluded that surface complexation plays an important role in the sorption of Cr(III) species on expanded perlite. In the case of bentonite, cation-exchange is the predominate mechanism for sorption of trivalent chromium ions, wherefore no net changes of zeta potential was observed after Cr(III) sorption. X-ray photoelectron spectroscopy measurements, at different pH values, were also made to corroborate the zeta potential results

  14. Evaluation of ethylenediaminetetraacetic acid (EDTA) solution and gel for smear layer removal.

    Science.gov (United States)

    Dotto, Sidney Ricardo; Travassos, Rosana Maria Coelho; de Oliveira, Elias Pandonor Motcy; Machado, Manoel Eduardo de Lima; Martins, José Luiz

    2007-08-01

    The purpose of this in vitro study was to compare the efficacy of 24% ethylenediaminetetraacetic acid (EDTA) gel and 17% EDTA solution in cleaning dentine walls after root canal instrumentation. Thirty human canine teeth were divided into three groups of 10 teeth each. In Group 1, 1% sodium hypochlorite was used as the irrigating solution; in Group 2, 1% sodium hypochlorite was used with 17% EDTA solution; and in Group 3, 1% sodium hypochlorite was used with 24% EDTA gel. The presence of a smear layer was analysed after instrumentation using scanning electron microscopy. The Kruskal-Wallis test revealed a statistical difference (P 0.05). The results indicate that 1% sodium hypochlorite alone does not remove the smear layer and that there was no statistical difference between EDTA gel and EDTA solution in smear layer removal.

  15. Removal of methylene blue from aqueous solution with magnetite loaded multi-wall carbon nanotube: Kinetic, isotherm and mechanism analysis

    International Nuclear Information System (INIS)

    Ai, Lunhong; Zhang, Chunying; Liao, Fang; Wang, Yao; Li, Ming; Meng, Lanying; Jiang, Jing

    2011-01-01

    Highlights: ► M-MWCNTs were synthesized by a facile one-pot solvothermal method and used as an efficient adsorbent for removing toxic dye from aqueous solution. ► The adsorption process was characterized by kinetics and isotherm analysis. ► FTIR analysis was employed to investigate the interactions between M-MWCNTs and dye. - Abstract: In this study, we have demonstrated the efficient removal of cationic dye, methylene blue (MB), from aqueous solution with the one-pot solvothermal synthesized magnetite-loaded multi-walled carbon nanotubes (M-MWCNTs). The as-prepared M-MWCNTs were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy. The effects of contact time, initial dye concentration, and solution pH on the adsorption of MB onto M-MWCNTs were systematically studied. It was shown that the MB adsorption was pH-dependent. Adsorption kinetics was best described by the pseudo-second-order model. Equilibrium data were well fitted to the Langmuir isotherm model, yielding maximum monolayer adsorption capacity of 48.06 mg g −1 . FTIR analysis suggested that the adsorption mechanism was possibly attributed to the electrostatic attraction and π–π stacking interactions between MWCNTs and MB.

  16. The removal of uranium (VI) from aqueous solutions onto activated carbon developed from grinded used tire.

    Science.gov (United States)

    Belgacem, Ahmed; Rebiai, Rachid; Hadoun, Hocine; Khemaissia, Sihem; Belmedani, Mohamed

    2014-01-01

    In this study, activated carbon was prepared from waste tire by KOH chemical activation. The pore properties including the BET surface area, pore volume, pore size distribution, and average pore diameter were characterized. BET surface area of the activated carbon was determined as 558 m(2)/g. The adsorption of uranium ions from the aqueous solution using this activated carbon has been investigated. Various physico-chemical parameters such as pH, initial metal ion concentration, and adsorbent dosage level and equilibrium contact time were studied by a batch method. The optimum pH for adsorption was found to be 3. The removal efficiency has also been determined for the adsorption system as a function of initial concentration. The experimental results were fitted to Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models. A comparison of best-fitting was performed using the coefficient of correlation and the Langmuir isotherm was found to well represent the measured sorption data. According to the evaluation using the Langmuir equation, the saturated monolayer sorption capacity of uranium ions onto waste tire activated carbon was 158.73 mg/g. The thermodynamic equilibrium constant and the Gibbs free energy were determined and results indicated the spontaneous nature of the adsorption process. Kinetics data were best described by pseudo-second-order model.

  17. Simultaneous removal of several heavy metals from aqueous solution by natural limestones

    Directory of Open Access Journals (Sweden)

    Sdiri A.

    2014-07-01

    Full Text Available Four natural limestone samples, collected from the Campanian-Maastrichtian limestones, Tunisia, were used as adsorbents for the removal of toxic metals in aqueous systems. The results indicated that high removal efficiency could be achieved by the present natural limestones. Among the metal ions studied, Pb2+ was the most preferably removed cation because of its high affinity to calcite surface. In binary system, the presence of Cu2+ effectively depressed the sorption of Cd2+ and Zn2+. Similarly Cu2+ strongly competed with Pb2+ to limestone surface. In ternary system, the removal further decreased, but considerable amount of Pb2+ and Cu2+ still occurred regardless of the limestone sample. The same behavior was observed in quadruple system, where the selectivity sequence was Pb2+ > Cu2+ > Cd2+ > Zn2+. From these results, it was concluded that the studied limestones have the required technical specifications to be used for the removal of toxic metals from wastewaters.

  18. Removal of plutonium from nitric acid-oxalic acid solutions using anion exchange method

    International Nuclear Information System (INIS)

    Kasar, U.M.; Pawar, S.M.; Joshi, A.R.

    1999-01-01

    An anion exchange method using Amberlyst A-26 (MP) resin was developed for removal of Pu from nitric acid-oxalic acid solutions without destroying oxalate. The method consists of sorption of Pu(IV) on Amberlyst A-26, a macroporous anion exchange resin, from nitric acid-oxalic acid medium in the presence of Al(NO 3 ) 3 . Pu(IV) breakthrough capacity of Amberlyst A-26 using synthetic feed solution was determined. (author)

  19. Development of a mathematical model of a packed column for benzene removal from salt solutions

    International Nuclear Information System (INIS)

    Georgeton, G.K.

    1989-01-01

    A mathematical model of a packed column was developed to describe the removal of benzene from radioactive salt solutions at the Savannah River Site. The model was developed from existing, generalized mass transfer correlations for randomly dumped packing, and the correlations were adapted for structured packing. Thermophysical data specific to the solutions of interest were incorporated into the model. Verification of the code was completed using operating data from stripping columns at other locations

  20. Removal of Cr(VI and Toxic Ions from Aqueous Solutions and Tannery Wastewater Using Polymer-Clay Composites

    Directory of Open Access Journals (Sweden)

    Abd El-Azeem Sallam

    2017-10-01

    Full Text Available Polymer-clay composites were prepared by natural zeolite (clinoptilolite or naturally local clay deposits in an N,N-methylene-bis-acrylamide as cross-linked. The resultant composites were used for the removal of Cr(VI from an aqueous solution. Additionally, their effects on soluble ions of tannery wastewater were investigated. The produced composites were characterized using X-ray diffraction (XRD, Fourier transform infrared spectroscopy (FT-IR, and scanning electron microscopy (SEM. The results showed that Cr(VI removal is dependent upon initial concentrations and pH. The adsorption quantity of Cr(VI onto the polymerized clay deposit followed by polymerized zeolite exhibited higher values than their original samples. The polymer-clay composite of clay deposit showed the highest removal of 76.3–100% overall initial concentrations of 10–50 mg L−1 and at initial pH of 2. Kinetics of Cr(VI removal by various sorbents was predicted using a pseudo–second order model. Our findings showed that the levels of salinity and various soluble ions (Cr2+, Na+, Cl− and SO42− in tannery wastewater are very high, and their levels were reduced after treatment, especially by polymerized sorbents. It could be concluded that the polymer-clay composites may be employed as a highly efficient sorbent for the removal of Cr(VI and toxic ions from the wastewater.

  1. Zero-valent iron nanoparticles embedded into reduced graphene oxide-alginate beads for efficient chromium (VI) removal.

    Science.gov (United States)

    Lv, Xiaoshu; Zhang, Yuling; Fu, Wenyang; Cao, Jiazhen; Zhang, Jiao; Ma, Hanbo; Jiang, Guangming

    2017-11-15

    Zero-valent iron nanoparticles (Fe 0 NPs) technologies are often challenged by poor dispersibility, chemical instability to oxidation, and mobility during processing, storage and use. This work reports a facile approach to synthesize Fe 0 NPs embedded reduced graphene oxide-alginate beads (Fe@GA beads) via the immobilization of pre-synthesized Fe 0 NPs into graphene oxide modified alginate gel followed by a modelling and in-situ reduction process. The structure/composition characterization of the beads finds that the graphene sheets and the Fe 0 NPs (a shape of ellipsoid and a size of beads. We demonstrate that these Fe@GA beads show a robust performance in aqueous Cr(VI) removal. With a optimized Fe and alginate content, Fe@GA bead can achieve a high Cr(VI) removal efficiency and an excellent mechanical strength. The initial Cr(VI) concentration, ionic strength, temperature and especially solution pH are all critical factors to control the Fe@GA beads performance in Cr(VI) removal. Fitness of the pseudo second-order adsorption model with data suggests adsorption is the rate-controlling step, and both Langmuir and Freundlich adsorption isotherm are suitable to describe the removal behavior. The possible Cr(VI) removal path by Fe@GA beads is put forward, and the synergistic effect in this ternary system implies the potentials of Fe@GA beads in pollutant removal from water body. Copyright © 2017 Elsevier Inc. All rights reserved.

  2. Simultaneous cadmium removal and 2,4-dichlorophenol degradation from aqueous solutions by Phanerochaete chrysosporium

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Anwei; Zeng, Guangming; Chen, Guiqiu; Fan, Jiaqi; Zou, Zhengjun; Li, Hui; Hu, Xinjiang; Long, Fei [Hunan Univ., Changsha (China). College of Environmental Science and Engineering; Ministry of Education, Changsha (CN). Key Lab. of Environmental Biology and Pollution Control (Hunan Univ.)

    2011-08-15

    Phanerochaete chrysosporium has been recognised as an effective bioremediation agent due to its unique degradation to xenobiotic and biosorption ability to heavy metals. However, few studies have focused on the simultaneous removal of heavy metals and organic pollutants. The aim of this work was to study the feasibility of simultaneous cadmium removal and 2,4-dichlorophenol (2,4-DCP) degradation in P. chrysosporium liquid cultures. The removal efficiencies were pH dependent and the maximum removal efficiencies were observed at pH 6.5 under an initial cadmium concentration of 5 mg/L and an initial 2,4-DCP concentration of 20 mg/L. The removal efficiencies for cadmium and 2,4-DCP reached 63.62% and 83.90%, respectively, under the optimum conditions. The high production levels of lignin peroxidase (7.35 U/mL) and manganese peroxidase (8.30 U/mL) resulted in an increase in 2,4-DCP degradation. The protein content decreased with increasing cadmium concentration. The surface characteristics and functional groups of the biomass were studied by scanning electron microscopy and a Fourier-transformed infrared spectrometer. The results showed that the use of P. chrysosporium is promising for the simultaneous removal of cadmium and 2,4-DCP from liquid media. (orig.)

  3. Comparison of Electrocoagulation and Chemical Coagulation Processes in Removing Reactive red 196 from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Ali Assadi

    2016-06-01

    Full Text Available Background: Conventional chemical coagulation is considered as an old method to dye and COD removal in textile effluent. Electrocoagulation (EC process is a robust method to achieve maximum removal. Methods: This study was designed to compare the result of operational parameters including optimum pH and coagulant concentration for chemical coagulation with ferric chloride and alum also, voltage, electrolysis time, initial pH, and conductivity for EC with iron electrodes to remove reactive red 196 (RR 196. Results: The outcomes show that ferric chloride and alum at optimum concentration were capable of removing dye and COD by 79.63 % and 84.83% and 53% and 55%, respectively. In contrast, EC process removed the dye and COD by 99.98% and 90.4%, respectively. Conclusion: The highest treatment efficiency was obtained by increasing the voltage, electrolysis time, pH and conductivity. Increase initial dye concentration reduces removal efficiency. Ultimately, it could be concluded that EC technology is an efficient procedure for handling of colored industrial wastewaters.

  4. Removal of Pertechnetate-Related Oxyanions from Solution Using Functionalized Hierarchical Porous Frameworks

    Energy Technology Data Exchange (ETDEWEB)

    Banerjee, Debasis [Physical and Computational Science Directorate, Pacific Northwest National Laboratory, Richland WA 99352 USA; Elsaidi, Sameh K. [Physical and Computational Science Directorate, Pacific Northwest National Laboratory, Richland WA 99352 USA; Chemistry Department, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia Alexandria 21321 Egypt; Aguila, Briana [Department of Chemistry, University of South Florida, USA; Li, Baiyan [Department of Chemistry, University of South Florida, USA; Kim, Dongsang [Energy and Environment Directorate, Pacific Northwest National Laboratory, Richland WA 99354 USA; Schweiger, Michael J. [Energy and Environment Directorate, Pacific Northwest National Laboratory, Richland WA 99354 USA; Kruger, Albert A. [US Department of Energy, Office of River Protection, Richland WA 99352 USA; Doonan, Christian J. [Department of Chemistry, The University of Adelaide, Adelaide South Australia 5005 Australia; Ma, Shengqian [Department of Chemistry, University of South Florida, USA; Thallapally, Praveen K. [Physical and Computational Science Directorate, Pacific Northwest National Laboratory, Richland WA 99352 USA

    2016-10-20

    Efficient and cost-effective removal of radioactive pertechnetate anions from nuclear waste is a key challenge to mitigate long-term nuclear waste storage issues. Traditional materials such as resins and layered double hydroxides (LDHs) were evaluated for their pertechnetate or perrhenate (the non-radioactive surrogate) removal capacity, but there is room for improvement in terms of capacity, selectivity and kinetics. A series of functionalized hierarchical porous frameworks were evaluated for their perrhenate removal capacity in the presence of other competing anions.

  5. INVESTIGATION OF CLINOPTILOLITE NATURAL ZEOLITE REGENERATION BY AIR STRIPPING FOLLOWED BY ION EXCHANGE FOR REMOVAL OF AMMONIUM FROM AQUEOUS SOLUTIONS

    Directory of Open Access Journals (Sweden)

    A. R. Rahmani ، M. T. Samadi ، H. R. Ehsani

    2009-07-01

    Full Text Available The purpose of this study was to regenerate clinoptilolite natural zeolite by air stripping followed by removal of ammonium from aqueous solutions. The research was carried out in continuous system. The characteristics of graded clinoptilolite from Semnan (one of the central provinces in Iran mines were determined and then regeneration tests were done by contacting of 1 N NaCl solution with given weights of ammonium saturated zeolite. Then the brine of column was transferred to the air stripping column for regeneration. The pH of brine solution before entrance to a stripping column was increased to 11. Air stripped ammonia from the brine was converted to the ammonium ion by using acid scrubber. The outlet effluent from stripping column was collected for reuse. The results showed that the cation exchange capacities were 17.31 to 18.38 mg NH4+/g of zeolite weight. Regeneration efficiency of zeolite by NaCl solution and air stripping was in the range of 92%-97% under various operational conditions. However, the efficiency of acid absorption of released ammonia in stripping process was 55% with a major rejection of the surplus ammonia to the atmosphere. It could be concluded that the method studied may be considered as an advanced and supplementary process for treating effluents of aqueous solution and fishponds in existing treatment plants.

  6. Evaluation of the Efficiency of Clay Pots in Removal of Water Impurities

    Directory of Open Access Journals (Sweden)

    K Naddafi , AH Mahvi, S Nasseri, M Mokhtari, H Zeraati

    2005-04-01

    Full Text Available Recently, inexpensive technologies for drinking water supply in small communities are highly considered in developing countries. One of these technologies is the application of ceramic filters that are usually made of diatomaceous earth or clay soil. This research was carried out to determine the efficiency of clay pots (as a filter in removing water impurities. Pilot and the related clay parts were manufactured and its efficiency in removing TDS, hardness, NO3-, color and turbidity was measured by passing water through the clay pipes. The results showed that the clay filters had not the potential to remove hardness, EC, TDS and nitrate of water. However, they showed excellent efficiency in turbidity removal (≥ 90% and could significantly decrease the color of the water (≥ 60%.

  7. THE EFFICIENCY OF ELECTROCOAGULATION PROCESS USING ALUMINUM ELECTRODES IN REMOVAL OF HARDNESS FROM WATER

    Directory of Open Access Journals (Sweden)

    M. Malakootian ، N. Yousefi

    2009-04-01

    Full Text Available There are various techniques for removal of water hardness each with its own special advantages and disadvantages. Electrochemical or electrocoagulation method due to its simplicity has gained a great attention and is used for removal of various ions and organic matters. The aim of the present study was to investigate the efficiency of this technique in removal of water hardness under different conditions. This experimental study was performed using a pilot plant. The applied pilot was comprised of a reservoir containing aluminum sheet electrodes. The electrodes were connected as monopolar and a power supply was used for supplying direct electrical current. Drinking water of Kerman (southeast of Iran was used in the experiments. The efficiency of the system in three different pH, voltages and time intervals were determined. Results showed the efficiency of 95.6% for electrocoagulation technique in hardness removal. pH and electrical potential had direct effect on hardness removal in a way that the highest efficiency rate was obtained in pH=10.1, potential difference of 20 volt and detention time of 60 minutes. Considering the obtained efficiency in the present study, electrocoagulation technique may be suggested as an effective alternative technique in hardness removal.

  8. Removal of copper and nickel contaminants from Si surface by use of cyanide solutions

    International Nuclear Information System (INIS)

    Fujiwara, N.; Liu, Y.-L.; Nakamura, T.; Maida, O.; Takahashi, M.; Kobayashi, H.

    2004-01-01

    The cleaning method using cyanide solutions has been developed to remove heavy metals such as copper (Cu) and nickel (Ni) from Si surfaces. Immersion of Si wafers with both Cu and Ni contaminants in potassium cyanide (KCN) solutions of methanol at room temperature decreases these surface concentrations below the detection limit of total reflection X-ray fluorescence spectroscopy of ∼3x10 9 atoms/cm 2 . UV spectra of the KCN solutions after cleaning of the Cu-contaminated Si surface show that stable copper-cyanide complexes are formed in the solution, leading to the prevention of the re-adsorption of copper in the solutions. From the complex stability constants, it is concluded that the Cu(CN) 4 3- is the most dominant species in the KCN solutions

  9. Application of H2O2 and H2O2/Fe0 in removal of Acid Red 18 dye from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Nazari Shahram

    2013-08-01

    Full Text Available Background & Aims of the Study: Organic dyes with a complex structure are often toxic, carcinogenic, mutagenic, non-biodegradation and stable in the environment and if released to the environment without treatment can endanger the environment and human health. The aim of this study was to evaluate the performance of H2O2 and H2O2/Fe0 Iron in removal of dye Acid Red 18 from aqueous solutions. Materials & Methods: This study was conducted at the laboratory scale. In this study, the removal efficiency of Acid Red 18 from a synthetic solution by H2O2 and H2O2/Fe0 was investigated. As well as Effect of solution pH, dye concentration, Concentration of Nanoscale Zero-Valent Iron, H2O2 and contact time in decolorization efficiency was investigated. Results: Results show that in pH=3, Contact time of 80 minutes, dye concentration of 50 mg/l and Concentration of Nanoscale Zero-Valent Iron of 2 g/l and H2O2 concentration equal to 200 mmol/l, the removal efficiency was about 98%. Conclusions: According to the results of experiments, H2O2/Fe0 has high efficiency in removal of Acid Red 18 from aqueous solution.

  10. THIOGLYCOLIC ACID ESTERIFIED IN TO RICE STRAW FOR REMOVING LEAD FROM AQUEOUS SOLUTION

    Directory of Open Access Journals (Sweden)

    R. Gong

    2011-09-01

    Full Text Available Thiol rice straw (TRS was prepared by esterifying thioglycolic acid onto rice straw in the medium of acetic anhydride and acetic acid with sulfuric acid as catalyst. The sorption of lead (Pb on TRS from aqueous solution was subsequently investigated. The batch experiments showed that Pb removal was dependent on initial pH, sorbent dose, Pb concentration, contact time, and temperature. The maximum value of Pb removal appeared at pH 5. For 100 mg/L of Pb solution, a removal ratio of greater than 98% could be achieved with 2.0 g/L or more of TRS. The isothermal data of Pb sorption conformed well to the Langmuir model, and the maximum sorption capacity (Qm of TRS for Pb was 104.17 mg/g. The equilibrium of Pb removal was reached within 120 min. The Pb removal process could be described by the pseudo-first-order kinetic model. The thermodynamic study indicated that the Pb removal process was spontaneous and endothermic.

  11. Remarkable efficiency of phosphate removal: Ferrate(VI)-induced in situ sorption on core-shell nanoparticles.

    Science.gov (United States)

    Kralchevska, Radina P; Prucek, Robert; Kolařík, Jan; Tuček, Jiří; Machala, Libor; Filip, Jan; Sharma, Virender K; Zbořil, Radek

    2016-10-15

    Despite the importance of phosphorus as a nutrient for humans and its role in ecological sustainability, its high abundance, resulting in large part from human activities, causes eutrophication that negatively affects the environment and public health. Here, we present the use of ferrate(VI) as an alternative agent for removing phosphorus from aqueous media. We address the mechanism of phosphate removal as a function of the Fe/P mass ratio and the pH value of the solution. The isoelectric point of γ-Fe2O3 nanoparticles, formed as dominant Fe(VI) decomposition products, was identified to play a crucial role in predicting their efficiency in removing of phosphates. Importantly, it was found that the removal efficiency dramatically changes if Fe(VI) is added before (ex-situ conditions) or after (in-situ conditions) the introduction of phosphates into water. Removal under in-situ conditions showed remarkable sorption capacity of 143.4 mg P per gram of ferric precipitates due to better accessibility of active surface sites on in-situ formed ferric oxides/oxyhydroxides. At pH = 6.0-7.0, complete removal of phosphates was observed at a relatively low Fe/P mass ratio (5:1). The results show that phosphates are removed from water solely by sorption on the surface of γ-Fe2O3/γ-FeOOH core/shell nanoparticles. The advantages of Fe(VI) utilization include its environmentally friendly nature, the possibility of easy separation of the final product from water by a magnetic field or by natural settling, and the capacity for successful phosphate elimination at pH values near the neutral range and at low Fe/P mass ratios. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Removal of cadmium(II) from aqueous solutions by steam-activated ...

    African Journals Online (AJOL)

    Removal of cadmium(II) from aqueous solutions by steam-activated sulphurised carbon prepared from sugar-cane bagasse pith: kinetics and equilibrium studies. ... the maximum adsorption capacity of SA-S-C calculated by the Langmuir isotherm is 149.93 mg/g at 30°C. Acid regeneration was tried for several cycles with a ...

  13. Aldehyde-functionalized porous nanocellulose for effective removal of heavy metal ions from aqueous solutions

    Science.gov (United States)

    C. Yao; F. Wang; Z. Cai; X. Wang

    2016-01-01

    Nanoscale sorption is a promising strategy for catalyst and purification system design. In this paper, cellulose nanofibrils (CNFs) were densely attached with aldehyde functional groups on the surface via a mild periodate oxidation process, and then applied as mesoporous sorbents to remove Cu(II) and Pb(II) from aqueous solutions. In the studied concentration range (0....

  14. Removal of heavy metal ions from aqueous solutions using lignocellulosic fibers

    Science.gov (United States)

    Beom-Goo Lee; Roger M. Rowell

    2004-01-01

    Spruce, coconut coir, sugarcane bagasse, kenaf bast, kenaf core, and cotton were tested for their ability to remove copper, nickel and zinc ions from aqueous-solutions as a function of their lignin content. The fibers were analyzed for sugar and lignin content and extracted with diethyl ether, ethyl alcohol. hot water, or 1% sodium hydroxide. The order of lignin...

  15. Application of Sargassum biomass to remove heavy metal ions from synthetic multi-metal solutions and urban storm water runoff.

    Science.gov (United States)

    Vijayaraghavan, K; Teo, Ting Ting; Balasubramanian, R; Joshi, Umid Man

    2009-05-30

    The ability of Sargassum sp. to biosorb four metal ions, namely lead, copper, zinc, and manganese from a synthetic multi-solute system and real storm water runoff has been investigated for the first time. Experiments on synthetic multi-solute systems revealed that Sargassum performed well in the biosorption of all four metal ions, with preference towards Pb, followed by Cu, Zn, and Mn. The solution pH strongly affected the metal biosorption, with pH 6 being identified as the optimal condition for achieving maximum biosorption. Experiments at different biosorbent dosages revealed that good biosorption capacity as well as high metal removal efficiency was observed at 3g/L. The biosorption kinetics was found to be fast with equilibrium being attained within 50 min. According to the Langmuir isotherm model, Sargassum exhibited maximum uptakes of 214, 67.5, 24.2 and 20.2mg/g for lead, copper, zinc, and manganese, respectively in single-solute systems. In multi-metal systems, strong competition between four metal ions in terms of occupancy binding sites was observed, and Sargassum showed preference in the order of Pb>Cu>Zn>Mn. The application of Sargassum to remove four heavy metal ions in real storm water runoff revealed that the biomass was capable of removing the heavy metal ions. However, the biosorption performance was slightly lower compared to that of synthetic metal solutions. Several factors were responsible for this difference, and the most important factor is the presence of other contaminants such as anions, organics, and other trace metals in the runoff.

  16. Removal of Lead Hydroxides Complexes from Solutions Formed in Silver/Gold: Cyanidation Process

    Science.gov (United States)

    Parga, José R.; Martinez, Raul Flores; Moreno, Hector; Gomes, Andrew Jewel; Cocke, David L.

    2014-04-01

    The presence of lead hydroxides in "pregnant cyanide solution" decreases the quality of the Dore obtained in the recovery processes of gold and silver, so it is convenient to remove them. The adsorbent capacity of the low cost cow bone powder was investigated for the removal of lead ions from a solution of lead hydroxide complexes at different initial metal ion concentrations (10 to 50 mg/L), and reaction time. Experiments were carried out in batches. The maximum sorption capacity of lead determined by the Langmuir model was found to be 126.58 mg/g, and the separation factor R L was between 0 and 1, indicating a significant affinity of bone for lead. Experimental data follow pseudo-second order kinetics suggesting chemisorption. It is concluded that cow bone powder can be successfully used for the removal of lead ions, and improves the quality of the silver-gold cyanides precipitate.

  17. Efficient interruption of infection chains by targeted removal of central holdings in an animal trade network.

    Science.gov (United States)

    Büttner, Kathrin; Krieter, Joachim; Traulsen, Arne; Traulsen, Imke

    2013-01-01

    Centrality parameters in animal trade networks typically have right-skewed distributions, implying that these networks are highly resistant against the random removal of holdings, but vulnerable to the targeted removal of the most central holdings. In the present study, we analysed the structural changes of an animal trade network topology based on the targeted removal of holdings using specific centrality parameters in comparison to the random removal of holdings. Three different time periods were analysed: the three-year network, the yearly and the monthly networks. The aim of this study was to identify appropriate measures for the targeted removal, which lead to a rapid fragmentation of the network. Furthermore, the optimal combination of the removal of three holdings regardless of their centrality was identified. The results showed that centrality parameters based on ingoing trade contacts, e.g. in-degree, ingoing infection chain and ingoing closeness, were not suitable for a rapid fragmentation in all three time periods. More efficient was the removal based on parameters considering the outgoing trade contacts. In all networks, a maximum percentage of 7.0% (on average 5.2%) of the holdings had to be removed to reduce the size of the largest component by more than 75%. The smallest difference from the optimal combination for all three time periods was obtained by the removal based on out-degree with on average 1.4% removed holdings, followed by outgoing infection chain and outgoing closeness. The targeted removal using the betweenness centrality differed the most from the optimal combination in comparison to the other parameters which consider the outgoing trade contacts. Due to the pyramidal structure and the directed nature of the pork supply chain the most efficient interruption of the infection chain for all three time periods was obtained by using the targeted removal based on out-degree.

  18. The Photocatalytic Removal of Ortho Chlorophenol from Aqueous Solution Using Modified Fly Ash - Titanium Dioxide

    Directory of Open Access Journals (Sweden)

    Mohamad Malakootian

    2016-05-01

    Full Text Available The photocatalytic process is a useful method for the effective removal of phenolic compounds. Conducted in the spring‒summer 2013 at the Engineering Research Center for Environmental Health, Kerman University of Medical Sciences, this experimental study used a modified fly ash‒TiO2 mixture to enhance the photocatalytic removal efficiency of ortho-chlorophenol. Fly ash obatined from the Thermal Power Plant in Zarand, Kerman, was initially washed with sulfuric acid before being oxidized with potassium permanganate. The mixture of modified fly ash and TiO2 was then used for the removal of ortho-chlorophenol in the presence of UV light and the factors involved in the removal process were optimized. It was found that the ortho-chlorophenol removal efficiency recorded by the mixture of modified fly ash and TiO2 was higher than that by each of the modified fly ash or TiO2/UV alone. It was, further, observed that removal efficiency with a modified fly ash to TiO2 ratio of 3:1 rose to 98.8% under optimum conditions (i.e., pH: 2; contact time: 2 h; room temperature (29±2˚C, and a catalyst dose of 0.6 g. The ortho-chlorophenol removal efficiency in real wastewater from the Coal Wash Plant in Zarand was recorded at 88.4%. Based on the results obtained from simultaneous use of modified fly ash and TiO2, the proposed method may be recommended for industrial applications.

  19. Using quartz sand to enhance the removal efficiency of M. aeruginosa by inorganic coagulant and achieve satisfactory settling efficiency.

    Science.gov (United States)

    Pei, Haiyan; Jin, Yan; Xu, Hangzhou; Ma, Chunxia; Sun, Jiongming; Li, Hongmin

    2017-10-19

    In this study, low-cost and non-polluting quartz sand was respectively mixed with AlCl 3 , FeCl 3 and PAFC to synergistically remove Microcystis aeruginosa. Results showed that quartz sand could markedly increase the algae removal efficiency and decrease the coagulant doses. The increase of removal efficiency with AlCl 3 and FeCl 3 was only due to the enhancement of floc density by the quartz sand. However, the removal efficiency with PAFC was increased not only by the enhanced floc density, but also by the enlarged floc size. Flocs from 50 mg/L sand addition were larger than that with other sand doses, which was on account of the appropriate enhancement of collision efficiency at this dose. After coagulation, the extracellular organic matter (EOM) and microcystins (MCs) in system with quartz sand was remarkably reduced. That's because quartz sand can enhance the coagulation so as to improve capping the EOM and MCs in flocs during coagulation process. Owing to 200 mg/L quartz sand could damage the cell's membrane during coagulation proces, algal cells in the system lysed two days earlier than with 50 mg/L sand during flocs storage. In addition, cells with PAFC incurred relatively moderate cellular oxidative damage and could remain intact for longer time.

  20. Evaluation of Efficacy of Advanced Oxidation Processes Fenton, Fenton-like and Photo-Fenton for Removal of Phenol from Aqueous Solutions

    International Nuclear Information System (INIS)

    Mofrad, M. R.; Akbari, H.; Miranzadeh, M. B.; Nezhad, M. E.; Atharizade, M.

    2015-01-01

    Contamination of water, soil and groundwater caused by aromatic compounds induces great concern in most world areas. Among organic pollutants, phenol is mostly considered dangerous due to its high toxicity for human and animal. Advanced oxidation processes (AOPs) is considered as a most efficient method also the best one for purifying organic compounds which are resistant to conventional physical and chemical processes. This experimental study was carried out in laboratory scale. First, a synthetic solution was made of phenol. Then, Fenton, Fenton-like and photo-Fenton processes were applied removing phenol from aquatic solution. The effects of Hydrogen Peroxide concentration, catalyst, pH and time were studied to phenol removal efficiency. Results showed that Photo-Fenton process with removal efficiency (97.5 percentage) is more efficient than Fenton and Fenton-like processes with removal efficiency (78.7 percentage and 82.5 percentage respectively), in pH=3, (H/sub 2/O/sub 2/)= 3mM, (Fe2+)= 0.1 mM, phenol concentration 100 mg L-1 and time reaction 60 min, the phenol removal was 97.5 percentage. (author)

  1. Efficiency of lead removal from drinking water using cationic resin Purolite

    Directory of Open Access Journals (Sweden)

    Ashour Mohammad Merganpour

    2015-01-01

    Full Text Available Background: Today, issues such as water shortage, difficulties and costs related to supplying safe water, and anomalous concentrations of heavy metals in groundwater and surface water resources, doubled the necessity of access to technical methods on removing these pollutants from water resources. Methods: In this lab study, cationic resin Purolite S-930 (with co-polymer styrene di-vinyl benzene structure was used for lead removal from drinking water containing up to 22 μg/L. Using statistical analysis and designing a full factorial experiment are the most important effective parameters on lead removal obtained through ion exchange process. Results: Analysis of response and interaction parameters of ion exchange showed that the resin column height has maximum and pH value has minimum effect on the efficiency of lead removal from aquatic environment. Trinary interaction of “effective size, flow rate, resin column high” has the most important for lead removal efficiency in this system. So the maximum efficiency was obtained at the mesh = 40, bed height =1.6 meter, and pH= 6.5. At the best operation conditions, ability to remove 95.42% of lead concentration can be achieved. Conclusion: Using the resin Purolite S-930 during 21-day service with 91.12% of mean lead removal ratio from drinking water is an economic and technical feasibility.

  2. Removal of radionuclides from partitioning waste solutions by adsorption and catalytic oxidation methods

    Energy Technology Data Exchange (ETDEWEB)

    Yamagishi, Isao; Yamaguchi, Isoo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kubota, Masumitsu [Research Organization for Information Science and Technology (RIST), Tokai, Ibaraki (Japan)

    2000-09-01

    Adsorption of radionuclides with inorganic ion exchangers and catalytic oxidation of a complexant were studied for the decontamination of waste solutions generated in past partitioning tests with high-level liquid waste. Granulated ferrocyanide and titanic acid were used for adsorption of Cs and Sr, respectively, from an alkaline solution resulting from direct neutralization of an acidic waste solution. Both Na and Ba inhibited adsorption of Sr but Na did not that of Cs. These exchangers adsorbed Cs and Sr at low concentration with distribution coefficients of more than 10{sup 4}ml/g from 2M Na solution of pH11. Overall decontamination factors (DFs) of Cs and total {beta} nuclides exceeded 10{sup 5} and 10{sup 3}, respectively, at the neutralization-adsorption step of actual waste solutions free from a complexant. The DF of total {alpha} nuclides was less than 10{sup 3} for a waste solution containing diethylenetriaminepentaacetic acid (DTPA). DTPA was rapidly oxidized by nitric acid in the presence of a platinum catalyst, and radionuclides were removed as precipitates by neutralization of the resultant solution. The DF of {alpha} nuclides increased to 8x10{sup 4} by addition of the oxidation step. The DFs of Sb and Co were quite low through the adsorption step. A synthesized Ti-base exchanger (PTC) could remove Sb with the DF of more than 4x10{sup 3}. (author)

  3. Application of a new adsorbent for fluoride removal from aqueous solutions

    International Nuclear Information System (INIS)

    Srivastav, Arun Lal; Singh, Prabhat K.; Srivastava, Varsha; Sharma, Yogesh C.

    2013-01-01

    Highlights: • A new adsorbent has been prepared. • The adsorbent is non-toxic and easy to synthesize. • HBO 1 has displayed best capacity for the removal of fluoride. • Unlike most adsorbents, HBO 1 is suitable for the removal of fluoride from water. • The process of removal has been optimized. -- Abstract: Hydrous bismuth oxides (HBOs) have been investigated as a possible adsorbent for fluoride removal from water. Apart from bismuth trioxide (Bi 2 O 3 ) compound, three additional HBOs, named as HBO 1 , HBO 2 , and HBO 3 were synthesized in the laboratory and examined for their relative potentials for fluoride removal from aqueous solutions. HBO 1 was observed to have highest fluoride removal at 10 mg/L initial concentration in aqueous environment. Among competitive anions, sulfate and chloride affect the fluoride removal by HBO 1 more adversely than bicarbonate. Characterization of HBOs using X-ray diffraction (XRD) pattern analyses indicated crystalline structures, and the broad chemical composition of materials showed successive increase of Bi(OH) 3 from HBO 1 to HBO 3 , with decrease of BiOCl in the same order. Fourier Transform Infrared (FTIR) spectroscopy analyses indicated presence of Bi-O bond and successively increasing number of peaks corresponding to OH ion from HBO 1 to HBO 3 . Scanning Electron Microscopic (SEM) images of HBOs show rough and porous structure of the materials. Presence of higher proportion of chloride compound in HBO 1 with respect to others appears to be the factor responsible for its better performance in fluoride removal from aqueous solutions

  4. Simultaneous removal of iron and manganese of aqueous solutions using as adsorbent a Mexican natural zeolite

    International Nuclear Information System (INIS)

    Garcia M, A.; Solache R, M. J.; Olguin G, M. T.

    2009-01-01

    In this work was evaluated the removal capacity of iron and manganese of aqueous solutions using a Mexican natural zeolite. It was observed that the Freundlich pattern describes the adsorption process appropriately and that a competitive effect exists between both metals by the exchange places of the zeolite, when it is starting of solutions that contain to both metals, impacting mainly in the manganese removal. A natural zeolite coming from the Puebla State, Mexico was used. The material was milled and sieved to a mesh size 30 and was conditioned with a solution 0.5 N of sodium chloride. Later on was characterized by means of scanning electron microscopy and X-ray diffraction.

  5. Removal of radium from aqueous solutions using adsorbent produced from coconut coir pith

    International Nuclear Information System (INIS)

    Zalina Laili; Muhamat Omar; Mohd Zaidi Ibrahim; Esther Phillip; Mohd Abdul Wahab Yusof; Hassan, A.

    2008-08-01

    A study was conducted to evaluate the potential use of the coconut coir pith as an adsorbent for the removal of radium from aqueous solutions. Experiments to establish adsorptions as a function of pH and contact time were carried out. The results showed that radium adsorption are dependent upon pH and contact time of coconut coir pith with aqueous solutions. 70-80% of radium were adsorbed in the neutral to alkaline pH range. The amount of radium adsorbed also increased with contact time, reaching an optimum after 250 min. Thus, it can be concluded that the coconut coir pith has the potential to be used as an adsorbent in radium removal from aqueous solutions. (Author)

  6. An experimental study on removal efficiency of bio-particles in an airtight decontamination chamber

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yanju [School of Environment Science and Technology, Tianjin University, Tianjin (China); National Biological Protection Engineering Center, Tianjin (China); Hao, Limei; Wang, Shuang; Hou, Lili; Zhang, Jinming; Qi, Jiancheng [National Biological Protection Engineering Center, Tianjin (China)

    2009-11-15

    Many bacteria and viruses lead to global dissemination of respiratory diseases, such as SARS, influenza, tuberculosis, pneumonia and asthma, by clinging to particles and transmission through aerosol. In this paper, an experiment was conducted to investigate the removal efficiency of bio-particles when exposed to ventilation in an airtight decontamination chamber made of stainless steel. After the bio-particles (Serratia marcescens) exposure condition was established in the chamber, the bio-particles removal efficiency was investigated. And a comparison experiment was then conducted with polystyrene latex spheres (PSL) as general particles under the same environmental condition. The comparison results indicate that the removal efficiency of bio-particles is lower than that of PSL during the first 300 s, but both removal efficiencies reached 90% almost at the same time. Furthermore, the differences between bio-particles and PSL, the influence of bio-particle size, environmental velocity, temperature and relative humidity on bio-particle removal efficiency were analyzed and discussed comprehensively. These data could not only underpin future numerical simulations of bio-particles, but also give information to aid in decisions for decreasing the risk of bio-particles pollution in a microbe exposure environment. (author)

  7. From illite/smectite clay to mesoporous silicate adsorbent for efficient removal of chlortetracycline from water.

    Science.gov (United States)

    Wang, Wenbo; Tian, Guangyan; Zong, Li; Zhou, Yanmin; Kang, Yuru; Wang, Qin; Wang, Aiqin

    2017-01-01

    A series of mesoporous silicate adsorbents with superior adsorption performance for hazardous chlortetracycline (CTC) were sucessfully prepared via a facile one-pot hydrothermal reaction using low-cost illite/smectite (IS) clay, sodium silicate and magnesium sulfate as the starting materials. In this process, IS clay was "teared up" and then "rebuilt" as new porous silicate adsorbent with high specific surface area of 363.52m 2 /g (about 8.7 folds higher than that of IS clay) and very negative Zeta potential (-34.5mV). The inert SiOSi (Mg, Al) bonds in crystal framework of IS were broken to form Si(Al) O - groups with good adsorption activity, which greatly increased the adsorption sites served for holding much CTC molecules. Systematic evaluation on adsorption properties reveals the optimal silicate adsorbent can adsorb 408.81mg/g of CTC (only 159.7mg/g for raw IS clay) and remove 99.3% (only 46.5% for raw IS clay) of CTC from 100mg/L initial solution (pH3.51; adsorption temperature 30°C; adsorbent dosage, 3g/L). The adsorption behaviors of CTC onto the adsorbent follows the Langmuir isotherm model, Temkin equation and pseudo second-order kinetic model. The mesopore adsorption, electrostatic attraction and chemical association mainly contribute to the enhanced adsorption properties. As a whole, the high-efficient silicate adsorbent could be candidates to remove CTC from the wastewater with high amounts of CTC. Copyright © 2016. Published by Elsevier B.V.

  8. Enzymatic removal of estrogenic activity of nonylphenol and octylphenol aqueous solutions by immobilized laccase from Trametes versicolor

    Energy Technology Data Exchange (ETDEWEB)

    Catapane, Maria [Institute of Genetics and Biophysics “ABT”, Via P. Castellino, 111, 80131 Naples (Italy); National Institute of Biostructures and Biosystems (INBB), Viale Medaglie d’Oro, 305, 00136 Rome (Italy); Nicolucci, Carla; Menale, Ciro; Mita, Luigi [National Institute of Biostructures and Biosystems (INBB), Viale Medaglie d’Oro, 305, 00136 Rome (Italy); Department of Experimental Medicine, Second University of Naples, Via S. M. di Costantinopoli, 16, 80138 Naples (Italy); Rossi, Sergio [Institute of Genetics and Biophysics “ABT”, Via P. Castellino, 111, 80131 Naples (Italy); Mita, Damiano G., E-mail: mita@igb.cnr.it [Institute of Genetics and Biophysics “ABT”, Via P. Castellino, 111, 80131 Naples (Italy); National Institute of Biostructures and Biosystems (INBB), Viale Medaglie d’Oro, 305, 00136 Rome (Italy); Department of Experimental Medicine, Second University of Naples, Via S. M. di Costantinopoli, 16, 80138 Naples (Italy); Diano, Nadia [Institute of Genetics and Biophysics “ABT”, Via P. Castellino, 111, 80131 Naples (Italy); National Institute of Biostructures and Biosystems (INBB), Viale Medaglie d’Oro, 305, 00136 Rome (Italy); Department of Experimental Medicine, Second University of Naples, Via S. M. di Costantinopoli, 16, 80138 Naples (Italy)

    2013-03-15

    Highlights: ► Endocrine disruptors cause adverse effects in living organisms. ► Nonylphenol and Octylphenol are alkylphenols recognized as endocrine disruptors. ► It is necessary to remove or reduce their presence in the environment. ► Waters polluted by these pollutants have been bioremediated by immobilized laccase from Trametes versicolor. ► Laccase treated solutions were found to have lost any estrogenic activity. -- Abstract: A fluidized bed reactor, filled with laccase-based beads, has been employed to bioremediate aqueous solutions polluted by endocrine disruptors belonging to the alkylphenols (APs) class. In particular Octylphenol and Nonylphenol have been studied. The catalytic activity of free and immobilized laccase from Trametes versicolor has been characterized as a function of pH, temperature and substrate concentration in the reaction medium. In view of practical applications for each substrate concentration the removal efficiency (RE), the time to halve the initial concentration (τ{sub 50}), and the t{sub c=0}, i.e. the time to reach complete pollutant removal, have been calculated. The immobilized laccase exhibited a lower affinity for octylphenol (K{sub m} = 1.11 mM) than for Nonylphenol (K{sub m} = 0.72 mM), but all the other parameters of applicative interest resulted more significant for octylphenol. For example, the times to reach the complete removal of octylphenol compared to those for nonylphenol at the same concentration is shorter of about 15% (at low concentrations) up to 40% (at high concentrations). The study of cell proliferation with MPP89 cells, a human mesothelioma cell line, and the assay with the YES test indicated the loss of estrogenic activity of the APs solutions after laccase treatment.

  9. Eggshell Powder as an Adsorbent for Removal of Fluoride from Aqueous Solution: Equilibrium, Kinetic and Thermodynamic Studies

    Directory of Open Access Journals (Sweden)

    R. Bhaumik

    2012-01-01

    Full Text Available A new medium, eggshell powder has been developed for fluoride removal from aqueous solution. Fluoride adsorption was studied in a batch system where adsorption was found to be pH dependent with maximum removal efficiency at 6.0. The experimental data was more satisfactorily fitted with Langmuir isotherm model. The kinetics and the factor controlling adsorption process fully accepted by pseudo-second-order model were also discussed. Ea was found to be 45.98 kJmol-1 by using Arrhenius equation, indicating chemisorption nature of fluoride onto eggshell powder. Thermodynamic study showed spontaneous nature and feasibility of the adsorption process with negative enthalpy (∆H0 value also supported the exothermic nature. Batch experiments were performed to study the applicability of the adsorbent by using fluoride contaminated water collected from affected areas. These results indicate that eggshell powder can be used as an effective, low-cost adsorbent to remove fluoride from aqueous solution as well as groundwater.

  10. Precipitation process for the removal of technetium values from nuclear waste solutions

    Science.gov (United States)

    Walker, D.D.; Ebra, M.A.

    1985-11-21

    High efficiency removal of techetium values from a nuclear waste stream is achieved by addition to the waste stream of a precipitant contributing tetraphenylphosphonium cation, such that a substantial portion of the technetium values are precipitated as an insoluble pertechnetate salt.

  11. Removal of zinc from aqueous solution by metal resistant symbiotic bacterium Mesorhizobium amorphae

    DEFF Research Database (Denmark)

    Hao, Xiuli; Mohamad, Osama Abdalla; Xie, Pin

    2014-01-01

    Biosorption of zinc by living biomasses of metal resistant symbiotic bacterium Mesorhizobium amorphae CCNWGS0123 was investigated under optimal conditions at pH 5.0, initial metal concentrations of 100 mg L-1, and a dose of 1.0 g L-1. M. amorphae exhibited an efficient removal of Zn2+ from aqueous...

  12. Efficiency of Aluminum and Iron Electrodes for the Removal of Heavy Metals [(Ni (II), Pb (II), Cd (II)] by Electrocoagulation Method

    Energy Technology Data Exchange (ETDEWEB)

    Khosa, Muhammad Kaleem; Jamal, Muhammad Asghar; Hussain, Amira; Muneer, Majid; Zia, Khalid Mahmood [Government College Univ., Faisalabad (Pakistan); Hafeez, Samia [Bahaud-din-Zakariya Univ., Multan (Pakistan)

    2013-06-15

    Electrocoagulation (EC) technique is applied for the treatment of wastewater containing heavy metals ions such as nickel (Ni), lead (Pb) and cadmium (Cd) by using sacrificial anodes corrode to release active coagulant flocs usually aluminium or iron cations into the solution. During electrolytic reactions hydrogen gas evolve at the cathode. All the experiments were carried out in Batch mode. The tank was filled with synthetic wastewater containing heavy metals and efficiency of electrocoagulation in combination with aluminum and iron electrodes were investigated for removal of such metals. Several parameters, such as contact time, pH, electro-coagulant concentration, and current density were optimized to achieve maximum removal efficiency (%). The concentrations of heavy metals were determined by using Atomic Absorption Spectroscopy (AAS). It is found that the electro-coagulation process has potential to be utilized for the cost-effective removal of heavy metals from wastewater specially using iron electrodes in terms of high removal efficiencies and operating cost.

  13. Efficiency of Aluminum and Iron Electrodes for the Removal of Heavy Metals [(Ni (II), Pb (II), Cd (II)] by Electrocoagulation Method

    International Nuclear Information System (INIS)

    Khosa, Muhammad Kaleem; Jamal, Muhammad Asghar; Hussain, Amira; Muneer, Majid; Zia, Khalid Mahmood; Hafeez, Samia

    2013-01-01

    Electrocoagulation (EC) technique is applied for the treatment of wastewater containing heavy metals ions such as nickel (Ni), lead (Pb) and cadmium (Cd) by using sacrificial anodes corrode to release active coagulant flocs usually aluminium or iron cations into the solution. During electrolytic reactions hydrogen gas evolve at the cathode. All the experiments were carried out in Batch mode. The tank was filled with synthetic wastewater containing heavy metals and efficiency of electrocoagulation in combination with aluminum and iron electrodes were investigated for removal of such metals. Several parameters, such as contact time, pH, electro-coagulant concentration, and current density were optimized to achieve maximum removal efficiency (%). The concentrations of heavy metals were determined by using Atomic Absorption Spectroscopy (AAS). It is found that the electro-coagulation process has potential to be utilized for the cost-effective removal of heavy metals from wastewater specially using iron electrodes in terms of high removal efficiencies and operating cost

  14. Furosemide removal in constructed wetlands: Comparative efficiency of LECA and Cork granulates as support matrix.

    Science.gov (United States)

    Machado, A I; Dordio, A; Fragoso, R; Leitão, A E; Duarte, E

    2017-12-01

    The removal efficiency of LECA and cork granulates as support matrix for pharmaceuticals active compounds in a constructed wetland system was investigated using the diuretic drug Furosemide. Kinetics studies were performed testing three different concentrations of Furosemide in an ultrapure water matrix, along seven days. LECA achieved higher removal values compared to cork granulates. However, cork granulates presented a higher removal in the first 24 h of contact time compared to the other adsorbent. The kinetic studies showed that LECA and cork granulates have different adsorption behaviours for Furosemide which is controlled by different adsorption mechanisms. Both materials showed good removal efficiencies and a combination of the two should be further explored in order to applied both materials as support matrix to cope with different furosemide concentrations. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Mercury removal from solution by superconducting magnetic separation with nanostructured magnetic adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    Okamoto, T., E-mail: okamoto-takayuki@ed.tmu.ac.jp [Graduate School of Science and Engineering, Tokyo Metropolitan University, 1-1 Minami-Osawa, Hachioji, Tokyo 192-0397 (Japan); Tachibana, S.; Miura, O. [Graduate School of Science and Engineering, Tokyo Metropolitan University, 1-1 Minami-Osawa, Hachioji, Tokyo 192-0397 (Japan); Takeuchi, M. [Komazawa Jin Clinic, 1-19-8 Komazawa, Setagayaku, Tokyo 154-0012 (Japan)

    2011-11-15

    Recently, mercury Hg concentration in human blood increases due to expanding the global mercury contamination. Excess mercury bioaccumulation poses a significant health risk. In order to decrease mercury concentration in the environment and human blood, we have developed two different kinds of nanostructured magnetic adsorbents for mercury to apply them to superconducting magnetic separation instead of conventional filtration. One is magnetic beads (MBs) which have nanosize magnetite particles in the core and a lot of SH radicals on the surface to adsorb Hg ions effectively. MBs were developed mainly to remove mercury from human blood. The maximum amount of the adsorption for MBs is 6.3 mg/g in the solution in less than a minute. Dithiothreitol can easily remove mercury adsorbed to MBs, hence MBs can be reusable. The other is nanostructured magnetic activated carbon (MAC) which is activated carbon with mesopores and nanosize magnetite. The maximum amount of the adsorption for MAC is 38.3 mg/g in the solution. By heat-treatment mercury can be easily removed from MAC. We have studied superconducting magnetic separation using each adsorbent for mercury removal from solution.

  16. Improvement of the Separation Efficiency of Ion Flotation and Adsorbing Colloid Flotation by the Synergistic Effect of Mixed Surfactant Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Kim, K.H.; Seo, E.J.; Choi, S.J. [Dept. of. Env. Eng., Kyungpook National University, Taegu (Korea)

    1999-02-01

    Experimental investigations on the removal of Cd(II) from aqueous ablution were carried out through two foam separation techniques : ion floatation and adsorbing colloid flotation with Fe(III). The optimum pH for good removal was found to be about 6.4 for the former and about 11 for the latter. The effect of flotation time. pH, surfactant(sodium lauryl sulfate), foreign ions(Na{sup +}, Ca{sup 2+}, No{sub 3}{sup -}, SO{sub 2}{sup -4} ) on the efficiency of Cd(II) removal were discussed. The presence of foreign ions inhibit the Cd(II) removal by foam flotation. It was suggested that the limitation of foam flotation on Cd(II) removal may be overcome by the surface activity of mixed surfactant solution. The application of the synergistic effect of mixed surfactant solutions to the improvement of the removal efficiency of foam flotation was experimentally verified in this work. 19 refs., 7 figs., 3 tabs.

  17. Pareto Efficient Solutions of Attack-Defence Trees

    DEFF Research Database (Denmark)

    Aslanyan, Zaruhi; Nielson, Flemming

    2015-01-01

    Attack-defence trees are a promising approach for representing threat scenarios and possible countermeasures in a concise and intuitive manner. An attack-defence tree describes the interaction between an attacker and a defender, and is evaluated by assigning parameters to the nodes, such as proba......Attack-defence trees are a promising approach for representing threat scenarios and possible countermeasures in a concise and intuitive manner. An attack-defence tree describes the interaction between an attacker and a defender, and is evaluated by assigning parameters to the nodes......, such as probability or cost of attacks and defences. In case of multiple parameters most analytical methods optimise one parameter at a time, e.g., minimise cost or maximise probability of an attack. Such methods may lead to sub-optimal solutions when optimising conflicting parameters, e.g., minimising cost while...... maximising probability. In order to tackle this challenge, we devise automated techniques that optimise all parameters at once. Moreover, in the case of conflicting parameters our techniques compute the set of all optimal solutions, defined in terms of Pareto efficiency. The developments are carried out...

  18. Modeling the removal of Sunfix Red S3B from aqueous solution by electrocoagulation process using artificial neural network

    Directory of Open Access Journals (Sweden)

    Manh Ha Bui

    2016-01-01

    Full Text Available This study presents an application of artificial neural networks (ANNs to predict the dye removal efficiency (color and chemical oxygen demand value of Electrocoagulation process from Sunfix Red S3B aqueous solution. The Bayesian regulation algorithm was applied to train the networks with experimental data including five factors: pH, current density, sulphate concentration, initial dye concentration (IDC, and electrolysis time. The predicting performance of the ANN models was validated through the low root mean square error value (9.844 %, mean absolute percentage error (13.776 % and the high determination coefficient value (0.836. Garson, Connection weight method and neural interpretation diagram were also used to study the influence of input variables on dye removal efficiency. For decolorization, the most effective inputs are determined as current density, electrolysis time and initial pH, while COD removal is found to be strongly affected by initial dye concentration and sulphate concentration. Through these steps, we demonstrated ANN’s robustness in modeling and analysis of electrocoagulation process.

  19. Possibility of increasing the efficiency of laser-induced tattoo removal by optical skin clearing

    Science.gov (United States)

    Genina, E. A.; Bashkatov, A. N.; Tuchin, V. V.; Altshuler, G. B.; Yaroslavskii, I. V.

    2008-06-01

    The possibility of selective laser photothermolysis improvement for the removal of tattoo pigments due to the optical clearing of human skin is investigated. It is shown experimentally that the optical skin clearing increases the tattoo image contrast. Computer Monte Carlo simulations show that by decreasing the laser beam scattering in upper skin layers, it is possible to reduce the radiation power required for tattoo removal by 30%—40% and, therefore, to increase the the photothermolysis efficiency.

  20. Self-assembly modified-mushroom nanocomposite for rapid removal of hexavalent chromium from aqueous solution with bubbling fluidized bed.

    Science.gov (United States)

    Xu, Fei; Liu, Xu; Chen, Yijiao; Zhang, Ke; Xu, Heng

    2016-05-18

    A self-assembled modified Pleurotus Cornucopiae material (SMPM) combined with improved Intermittent Bubbling Fluidized Bed (IBFB) was investigated to remove the hexavalent chromium ions in aqueous solution. After the modification, the powder-like raw material gradually self-assembled together to SMPM, which had crinkly porous structure, improved the Cr-accommodation ability in a sound manner. Optimized by Taguchi method, Cr(VI) removal efficiency was up to 75.91% and 48.01% for 100 mg/L and 500 mg/L initial concentration of Cr(VI), respectively. Results indicated that the metal removal was dependent on dosage of adsorbent, particle diameter and treatment time. The experimental data obtained from the biosorption process was successfully correlated with Freundlich isotherm model. Thermodynamic study indicated the endothermic nature of the process. The results confirmed that self-assembly modified Pleurotus Cornucopiae material could be applied for the removal of heavy metal from wastewater in continuous fluidized bed process.

  1. Zero-valent iron particles embedded on the mesoporous silica–carbon for chromium (VI) removal from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Xiong, Kun, E-mail: kunxiong312@gmail.com; Gao, Yuan [Chongqing Technology and Business University, Engineering Research Center for Waste Oil Recovery Technology and Equipment of Ministry of Education, Chongqing Key Laboratory of Catalysis & Environmental New Materials (China); Zhou, Lin [Chengdu Radio and TV University (China); Zhang, Xianming [Chongqing Technology and Business University, Engineering Research Center for Waste Oil Recovery Technology and Equipment of Ministry of Education, Chongqing Key Laboratory of Catalysis & Environmental New Materials (China)

    2016-09-15

    Nanoscale zero-valent iron (nZVI) particles were embedded on the walls of mesoporous silica–carbon (MSC) under the conditions of high-temperature carbonization and reduction and used to remove chromium (VI) from aqueous solution. The structure and textural properties of nZVI–MSC were characterized by the powder X-ray diffraction, transmission electron microscopy and N{sub 2} adsorption and desorption. The results show that nZVI–MSC has highly ordered mesoporous structure and large surface area, indistinguishable with that of MSC. Compared with the support MSC and iron particles supported on the activated carbon (nZVI/AC), nZVI–MSC exhibited much higher Cr(VI) removal efficiency with about 98 %. The removal process obeys a pseudo first-order model. Such excellent performance of nZVI–MSC could be ascribed to the large surface and iron particles embedded on the walls of the MSC, forming an intimate contact with the MSC. It is proposed that this feature might create certain micro-electrode on the interface of iron particles and MSC, which prevented the formation of metal oxide on the surface and provided fresh Fe surface for Cr(VI) removal.

  2. Removal of blue indigo and cadmium present in aqueous solutions using a modified zeolitic material and an activated carbonaceous material

    International Nuclear Information System (INIS)

    Gutierrez S, E. E.

    2011-01-01

    In the last years the use of water has been increased substantially, it has been also altered its quality as a result of human activities such as mining, industrial activities and others. Water pollution caused by dyes and heavy metals has adverse effects on the environment, since both pollutants are very persisten even after conventional treatments. Denim blue and cadmium are not biodegradable. There is a growing interest in finding new, efficient and low cost alternative materials to remove such pollutants from the aqueous medium. The purpose of this work was to evaluate a modified zeolitic tuff and an activated carbonaceous material obtained from the pyrolysis of sewage sludge for the removal of denim blue and cadmium. The zeolitic material was modified with Na + and Fe 3+ solutions to improve its sorption properties for the removal of cadmium and denim blue, respectively. Carbonaceous material was treated with 10% HCl solution to remove ashes. Both materials were characterized by scanning electron microscopy and elemental analysis (EDS), specific surface areas (Bet), thermogravimetric analysis, infrared spectroscopy and X-ray diffraction. Simultaneously, the denim blue dye was characterized by infrared spectroscopy and its pKa value was determined, these data allowed the determination of its chemical properties and its acid-base behavior in solution. In the content of this work the term indigo blue was changed by denim blue, as it corresponds to the commercial name of the dye. To assess the sorption capacity of sorbents, the sorption kinetics and sorption isotherms in batch system were determined; the results were fitted to mathematical models such as the pseudo-first order, pseudo second order and second order to describe the sorption kinetics and the Langmuir, Freundlich and Langmuir-Freundlich isotherms to describe sorption processes. The results show that the most efficient material to remove denim blue from aqueous solutions is the carbonaceous material

  3. System solution to improve energy efficiency of HVAC systems

    Science.gov (United States)

    Chretien, L.; Becerra, R.; Salts, N. P.; Groll, E. A.

    2017-08-01

    According to recent surveys, heating and air conditioning systems account for over 45% of the total energy usage in US households. Three main types of HVAC systems are available to homeowners: (1) fixed-speed systems, where the compressor cycles on and off to match the cooling load; (2) multi-speed (typically, two-speed) systems, where the compressor can operate at multiple cooling capacities, leading to reduced cycling; and (3) variable-speed systems, where the compressor speed is adjusted to match the cooling load of the household, thereby providing higher efficiency and comfort levels through better temperature and humidity control. While energy consumption could reduce significantly by adopting variable-speed compressor systems, the market penetration has been limited to less than 10% of the total HVAC units and a vast majority of systems installed in new construction remains single speed. A few reasons may explain this phenomenon such as the complexity of the electronic circuitry required to vary compressor speed as well as the associated system cost. This paper outlines a system solution to boost the Seasonal Energy Efficiency Rating (SEER) of a traditional single-speed unit through using a low power electronic converter that allows the compressor to operate at multiple low capacity settings and is disabled at high compressor speeds.

  4. Removal of boron from aqueous solution by using neutralized red mud

    International Nuclear Information System (INIS)

    Cengeloglu, Yunus; Tor, Ali; Arslan, Gulsin; Ersoz, Mustafa; Gezgin, Sait

    2007-01-01

    The adsorptive removal of boron from aqueous solution by using the neutralized red mud was studied in batch equilibration technique. The effects of pH, adsorbent dosage, initial boron concentration and contact time on the adsorption were investigated. The experiments demonstrated that boron removal was of a little fluctuation in pH range of 2-7 and it takes 20 min to attain equilibrium. The adsorption data was analyzed using the Langmuir and the Freundlich isotherm models and it was found that the Freundlich isotherm model represented the measured sorption data well

  5. Application of X-ray scanning and tomography to evaluate the filtercake removal efficiency

    International Nuclear Information System (INIS)

    Lopes, R.T.; Oliveira, L.F. de; Miranda, C.R.; Leite, J.C.

    2004-01-01

    The removal of the filtercake formed during the drilling operation is essential for a successful cementing job. Nowadays, the use of synthetic base fluids brings the necessity of proceeding new evaluations of the efficiency of the washes in removing the filtercake and to guarantee the wettability inversion of the formation from oil to waterwet. It is presented here the application of X-ray tomographic scanning to evaluate the filtercake removal efficiency performed by different washes. This technique uses a natural core with a perforation, where a filtercake is formed by circulating a drilling fluid. The wash is circulated through this perforation and the filtercake removal efficiency is measured precisely by computer tomography scanning. This procedure enables the filtercake removal visualization during the wash circulation through the formation and from the data obtained from the X-ray tomography it is possible to select the most appropriate wash for a given drilling fluid, as well as to predict the necessary contact time between the wash and the formation to achieve an appropriate filtercake removal

  6. Laser scabbling for nuclear decommissioning: Effect of concrete composition on volume removal efficiency

    International Nuclear Information System (INIS)

    Peach, B.; Petkovski, M.; Blackburn, J.; Engelberg, D.L.

    2015-01-01

    The objective of this study was to determine the effect of concrete composition and moisture content on volume removal with the overarching goal to identify mechanism(s) responsible for laser scabbling. Tests under application of fixed laser parameters showed that concrete composition had a significant effect on material removal but the investigation into moisture content was inconclusive. The mechanical properties and size of coarse aggregates seemed to affect scabbling efficiency, rather than their chemical properties. The presence of pulverized fuel ash as a cement replacement material indicated to be a major factor that determines material removal volumes. (authors)

  7. Fractional Factorial Design Study on the Performance of GAC-Enhanced Electrocoagulation Process Involved in Color Removal from Dye Solutions

    Directory of Open Access Journals (Sweden)

    Iuliana Gabriela Breaban

    2013-07-01

    Full Text Available The aim of this study was to determine the effects of main factors and interactions on the color removal performance from dye solutions using the electrocoagulation process enhanced by adsorption on Granular Activated Carbon (GAC. In this study, a mathematical approach was conducted using a two-level fractional factorial design (FFD for a given dye solution. Three textile dyes: Acid Blue 74, Basic Red 1, and Reactive Black 5 were used. Experimental factors used and their respective levels were: current density (2.73 or 27.32 A/m2, initial pH of aqueous dye solution (3 or 9, electrocoagulation time (20 or 180 min, GAC dose (0.1 or 0.5 g/L, support electrolyte (2 or 50 mM, initial dye concentration (0.05 or 0.25 g/L and current type (Direct Current—DC or Alternative Pulsed Current—APC. GAC-enhanced electrocoagulation performance was analyzed statistically in terms of removal efficiency, electrical energy, and electrode material consumptions, using modeling polynomial equations. The statistical significance of GAC dose level on the performance of GAC enhanced electrocoagulation and the experimental conditions that favor the process operation of electrocoagulation in APC regime were determined. The local optimal experimental conditions were established using a multi-objective desirability function method.

  8. Synthesis and Application of Iron Oxide/Silica Gel Nanocomposite for Removal of Sulfur Dyes from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Naser Tavassoli

    2017-03-01

    Full Text Available Background & Aims of the Study: water pollution by synthetic organic dyes is mainly regarded as environmental and ecological critical issues worldwide. In this research, magnetite iron oxide/silica gel nanocomposite (termed as Fe3O4/SG was synthesized chemically and then used as an effective adsorbent for removal of sulfur dyes from aqueous solution. Materials and Methods: The various parameters such as pH, sorbent dosage, initial dye concentration, contact time and dye solution temperature were investigated in a batch system. The equilibrium data were analyzed by Langmuir and Freundlich isotherm models. Results: The experimental data fit well with pseudo-second-order kinetic model (R2≥0.998 and conformed better to Langmuir isotherm model (R2≥0.997. The maximum adsorption capacity for Fe3O4/SG obtained from the Langmuir model was 11.1mg/g. Evaluation of thermodynamic parameters proved that the adsorption process was normally feasible, spontaneous and exothermic. Conclusion: It can be concluded that the Fe3O4/SG can be considered as a cost-effective and an environmental friendly adsorbent for efficient removal of sulfur dyes from aqueous solutions.

  9. Fractional Factorial Design Study on the Performance of GAC-Enhanced Electrocoagulation Process Involved in Color Removal from Dye Solutions.

    Science.gov (United States)

    Secula, Marius Sebastian; Cretescu, Igor; Cagnon, Benoit; Manea, Liliana Rozemarie; Stan, Corneliu Sergiu; Breaban, Iuliana Gabriela

    2013-07-10

    The aim of this study was to determine the effects of main factors and interactions on the color removal performance from dye solutions using the electrocoagulation process enhanced by adsorption on Granular Activated Carbon (GAC). In this study, a mathematical approach was conducted using a two-level fractional factorial design ( FFD ) for a given dye solution. Three textile dyes: Acid Blue 74, Basic Red 1, and Reactive Black 5 were used. Experimental factors used and their respective levels were: current density (2.73 or 27.32 A/m²), initial pH of aqueous dye solution (3 or 9), electrocoagulation time (20 or 180 min), GAC dose (0.1 or 0.5 g/L), support electrolyte (2 or 50 mM), initial dye concentration (0.05 or 0.25 g/L) and current type (Direct Current- DC or Alternative Pulsed Current- APC ). GAC-enhanced electrocoagulation performance was analyzed statistically in terms of removal efficiency, electrical energy, and electrode material consumptions, using modeling polynomial equations. The statistical significance of GAC dose level on the performance of GAC enhanced electrocoagulation and the experimental conditions that favor the process operation of electrocoagulation in APC regime were determined. The local optimal experimental conditions were established using a multi-objective desirability function method.

  10. Functionalization of Microcrystalline Cellulose with N,N-dimethyldodecylamine for the Removal of Congo Red Dye from an Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Dongying Hu

    2014-08-01

    Full Text Available Microcrystalline cellulose (MCC was functionalized with quaternary amine groups for use as an adsorbent to remove Congo Red dye (CR from aqueous solution. The ultrasonic pretreatment of MCC was investigated during its functionalization. Characterization was conducted using infrared spectroscopy (FT-IR, X-ray photoelectron spectroscopy (XPS, X-ray diffraction (XRD, and scanning electron microscopy (SEM. The batch adsorption of the functionalized MCC was studied to evaluate the effects of dye concentration, pH of solution, temperature, and NaCl concentration on the adsorption CR. The adsorbent (FM-1 obtained using ultrasonic pretreatment of MCC under 10.8 kJ•g–1 exhibited an adsorption capacity of 304 mg•g–1 at initial pH under a dose of 0.1 g•L–1 and initial concentration of 80 mg•L–1. After functionalization, the FT-IR and XPS results indicated that the quaternary amine group was successfully grafted onto the cellulose, the surface was transformed to be coarse and porous, and the crystalline structure of the original cellulose was disrupted. FM-1 has been shown to be a promising and efficient adsorbent for the removal of CR from an aqueous solution.

  11. Performance Evaluation of Bulk Liquid Membrane Technique on p-Nitrophenol Removal from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    K. Pourkhanali

    2018-03-01

    Full Text Available The transport of p-nitrophenol (PNP through a bulk liquid membrane (BLM was investigated to evaluate the effect of different experimental conditions on PNP partitioning behavior. The influence of solvent type, different salts in feed phase, the feed phase pH and PNP concentration in feed phase on transport efficiency of PNP through the BLM were studied. The results indicated that the highest removal efficiency of PNP was observed for 80 % xylene + 20 % toluene as liquid membrane, Na2SO4 as salt in feed phase, in the acidic feed phase and in 150 min. The effect of initial concentration of PNP on the efficiency of the separation PNP showed that the increase in initial concentration up to 350 ppm had positive effect, and more than 350 ppm had negative effect on the PNP removal behavior. Also, pertraction in BLM systems were described by a kinetic model of two consecutive irreversible first order chemical reactions.

  12. Design and characterization of sulfide-modified nanoscale zerovalent iron for cadmium(II) removal from aqueous solutions

    Science.gov (United States)

    Lv, Dan; Zhou, Xiaoxin; Zhou, Jiasheng; Liu, Yuanli; Li, Yizhou; Yang, Kunlun; Lou, Zimo; Baig, Shams Ali; Wu, Donglei; Xu, Xinhua

    2018-06-01

    Nanoscale zero-valent iron (nZVI) has high removal efficiency and strong reductive ability to organic and inorganic contaminants, but concerns over its stability and dispersity limit its application. In this study, nZVI was modified with sulfide to enhance Cd(II) removal from aqueous solutions. TEM and SEM analyses showed that sulfide-modified nZVI (S-nZVI) had a core-shell structure of nano-sized spherical particles, and BET results proved that sulfide modification doubled the specific surface area from 26.04 to 50.34 m2 g-1 and inhibited the aggregation of nZVI. Mechanism analysis indicated that Cd(II) was immobilized through complexation and precipitation. Cd(II) removal rate on nZVI was only 32% in 2 h, while complete immobilization could be achieved in 15 min on S-nZVI, and S-nZVI with an optimal S/Fe molar ratio of 0.3 offered a cadmium removal capacity of about 150 mg g-1 at pH 7 and 303 K. The process of Cd(II) immobilization on S-nZVI was fitted well with pseudo-second-order kinetic model, and the increase of temperature favored Cd(II) immobilization, suggesting an endothermic process. The presence of Mg2+ and Ca2+ hindered Cd(II) removal while Cu2+ did the opposite, which led to the order as Cu2+ > control > Mg2+ > Ca2+. The removal rate of 20 mg L-1 Cd(II) maintained a high level with the fluctuation of environmental conditions such as pH, ion strength and presence of HA. This study demonstrated that S-nZVI could be a promising adsorbent for Cd(II) immobilization from cadmium-contaminated water.

  13. In vitro assessment of cutting efficiency and durability of zirconia removal diamond rotary instruments.

    Science.gov (United States)

    Kim, Joon-Soo; Bae, Ji-Hyeon; Yun, Mi-Jung; Huh, Jung-Bo

    2017-06-01

    Recently, zirconia removal diamond rotary instruments have become commercially available for efficient cutting of zirconia. However, research of cutting efficiency and the cutting characteristics of zirconia removal diamond rotary instruments is limited. The purpose of this in vitro study was to assess and compare the cutting efficiency, durability, and diamond rotary instrument wear pattern of zirconia diamond removal rotary instruments with those of conventional diamond rotary instruments. In addition, the surface characteristics of the cut zirconia were assessed. Block specimens of 3 mol% yttrium cation-doped tetragonal zirconia polycrystal were machined 10 times for 1 minute each using a high-speed handpiece with 6 types of diamond rotary instrument from 2 manufacturers at a constant force of 2 N (n=5). An electronic scale was used to measure the lost weight after each cut in order to evaluate the cutting efficiency. Field emission scanning electron microscopy was used to evaluate diamond rotary instrument wear patterns and machined zirconia block surface characteristics. Data were statistically analyzed using the Kruskal-Wallis test, followed by the Mann-Whitney U test (α=.05). Zirconia removal fine grit diamond rotary instruments showed cutting efficiency that was reduced compared with conventional fine grit diamond rotary instruments. Diamond grit fracture was the most dominant diamond rotary instrument wear pattern in all groups. All machined zirconia surfaces were primarily subjected to plastic deformation, which is evidence of ductile cutting. Zirconia blocks machined with zirconia removal fine grit diamond rotary instruments showed the least incidence of surface flaws. Although zirconia removal diamond rotary instruments did not show improved cutting efficiency compared with conventional diamond rotary instruments, the machined zirconia surface showed smoother furrows of plastic deformation and fewer surface flaws. Copyright © 2016 Editorial Council

  14. Optimization of Removal Efficiency and Minimum Contact Time for Cadmium and Zinc Removal onto Iron-modified Zeolite in a Two-stage Batch Sorption Reactor

    Directory of Open Access Journals (Sweden)

    M. Ugrina

    2018-01-01

    Full Text Available In highly congested industrial sites where significant volumes of effluents have to be treated in the minimum contact time, the application of a multi-stage batch reactor is suggested. To achieve better balance between capacity utilization and cost efficiency in design optimization, a two-stage batch reactor is usually the optimal solution. Thus, in this paper, a two-stage batch sorption design approach was applied to the experimental data of cadmium and zinc uptake onto iron-modified zeolite. The optimization approach involves the application of the Vermeulen’s approximation model and mass balance equation to kinetic data. A design analysis method was developed to optimize the removal efficiency and minimum total contact time by combining the time required in the two-stages, in order to achieve the maximum percentage of cadmium and zinc removal using a fixed mass of zeolite. The benefits and limitations of the two-stage design approach have been investigated and discussed

  15. Removal of Phosphate from Synthetic Aqueous Solution by Adsorption with Dolomite from Padalarang

    Directory of Open Access Journals (Sweden)

    Fadjari Lucia Nugroho

    2014-12-01

    Full Text Available The presence of phosphate in wastewaters can cause eutrophication of surface water bodies leading to algal-blooming in the aquatic environment and degradation of water quality. Phosphate removal from wastewaters by conventional biological treatment removes only 10-30% of the phosphate, whilst chemical treatment using precipitants such as calcium or iron salts, although effective, is expensive and produces water-rich sludge which must be further treated. Hence, phosphate removal by adsorption in the form of Ca -phosphate has been proposed as an alternative to the more traditional methods. This study investigated the feasibility of using dolomite–a common sedimentary rock–from Padalarang, West Java, Indonesia as the adsorbent for the removal of phosphate from synthetic aqueous solution. Chemical analysis revealed that the Padalarang dolomite contains 33.6-36.2% CaO. Batch experiments at room temperature indicated that optimum removal of phosphate was achieved at pH 9. At 25°C , where increasing concentrations of phosphate (10–100 mg/L increased phosphate adsorption (2.15-31.3 mg/g by the dolomite. The adsorption of phosphate could be described by the Langmuir isotherm model, with constants Qm= 476.19 mg/g, K L= 0,00106 L/mg and equilibrium parameter (R L: 0.904 – 0.989. Phosphate adsorption by dolomite not only permits its removal but also its potential recovery for reuse.

  16. Removal Efficiency of Nitrogen, Phosphorus and Heavy Metal by Intermittent Cycle Extended Aeration System from Municipal Wastewater (Yazd-ICEAS

    Directory of Open Access Journals (Sweden)

    Seyed Vahid Ghelmani

    2016-09-01

    Conclusion: The high removal efficiency of BOD5, TKN, and NH4+ showed that this advanced SBR system had an appropriate efficiency for nitrification. Phosphorus removal (TP had a lower efficiency than those of NH4+ and TKN, but it was within the environmental standard limits. On the other hand, in the advanced SBR the removal efficiency of heavy metals for Cd was not within the standard limits.

  17. The use of raw and acid-pretreated bivalve mollusk shells to remove metals from aqueous solutions

    International Nuclear Information System (INIS)

    Liu Yang; Sun Changbin; Xu Jin; Li Youzhi

    2009-01-01

    Heavy metal removal from industrial wastewater is not only to protect living organisms in the environment but also to conserve resources such as metals and water by enabling their reuse. To overcome the disadvantage of high cost and secondary pollution by the conventional physico-chemical treatment techniques, environmentally benign and low-cost adsorbents are in demand. In this study, the use of raw and acid-pretreated bivalve mollusk shells (BMSs) to remove metals from aqueous solutions with single or mixed metal was evaluated at different BMSs doses, pH and temperatures in batch shaking experiments in laboratory conditions. When the BMSs were used to treat CuSO 4 .5H 2 O solution, the copper sorption capacities of the raw and acid-pretreated BMSs were approximately 38.93 mg/g and 138.95 mg/g, respectively. The copper removal efficiency (CRE) of the raw BMSs became greatly enhanced with increasing initial pH, reaching 99.51% at the initial pH 5. Conversely, the CRE of the acid-pretreated BMSs was maintained at 99.48-99.52% throughout the pH range of 1-5. Furthermore, the CRE values of the raw and acid-pretreated BMSs were not greatly changed when the temperature was varied from 15 deg. C to 40 deg. C. In addition, the CRE value of the raw BMSs was maintained for 12 cycles of sorption-desorption with a CRE of 98.4% being observed in the final cycle. Finally, when the BMSs were used to treat electroplating wastewater, the removal efficiencies (REs) of the raw BMSs were 99.97%, 98.99% and 87% for Fe, Zn and Cu, respectively, whereas the REs of the acid-pretreated BMSs were 99.98%, 99.43% and 92.13%, respectively. Ion exchange experiments revealed that one of mechanisms for metal sorption by the BMSs from aqueous solution is related to ion exchange, especially between the metal ions in the treated solution and Ca 2+ from BMSs. Infrared absorbance spectra analysis indicated that the acid pretreatment led to occurrence of the groups (i.e. -OH, -NH, C=O and S=O) of

  18. The use of raw and acid-pretreated bivalve mollusk shells to remove metals from aqueous solutions.

    Science.gov (United States)

    Liu, Yang; Sun, Changbin; Xu, Jin; Li, Youzhi

    2009-08-30

    Heavy metal removal from industrial wastewater is not only to protect living organisms in the environment but also to conserve resources such as metals and water by enabling their reuse. To overcome the disadvantage of high cost and secondary pollution by the conventional physico-chemical treatment techniques, environmentally benign and low-cost adsorbents are in demand. In this study, the use of raw and acid-pretreated bivalve mollusk shells (BMSs) to remove metals from aqueous solutions with single or mixed metal was evaluated at different BMSs doses, pH and temperatures in batch shaking experiments in laboratory conditions. When the BMSs were used to treat CuSO(4)x5H(2)O solution, the copper sorption capacities of the raw and acid-pretreated BMSs were approximately 38.93 mg/g and 138.95 mg/g, respectively. The copper removal efficiency (CRE) of the raw BMSs became greatly enhanced with increasing initial pH, reaching 99.51% at the initial pH 5. Conversely, the CRE of the acid-pretreated BMSs was maintained at 99.48-99.52% throughout the pH range of 1-5. Furthermore, the CRE values of the raw and acid-pretreated BMSs were not greatly changed when the temperature was varied from 15 degrees C to 40 degrees C. In addition, the CRE value of the raw BMSs was maintained for 12 cycles of sorption-desorption with a CRE of 98.4% being observed in the final cycle. Finally, when the BMSs were used to treat electroplating wastewater, the removal efficiencies (REs) of the raw BMSs were 99.97%, 98.99% and 87% for Fe, Zn and Cu, respectively, whereas the REs of the acid-pretreated BMSs were 99.98%, 99.43% and 92.13%, respectively. Ion exchange experiments revealed that one of mechanisms for metal sorption by the BMSs from aqueous solution is related to ion exchange, especially between the metal ions in the treated solution and Ca(2+) from BMSs. Infrared absorbance spectra analysis indicated that the acid pretreatment led to occurrence of the groups (i.e. -OH, -NH, C=O and S

  19. Pb(II) removal from aqueous solution by a low-cost adsorbent dry desulfurization slag

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Qiong; You, Ruirong [College of Materials Science and Engineering, Fuzhou University, New Campus, Minhou, Fujian Province 350108 (China); Clark, Malcolm [Marine Ecology Research Centre, School of Environment, Science and Engineering, Southern Cross University, P.O. Box 157, Lismore, NSW 2480 (Australia); Yu, Yan, E-mail: yuyan_1972@126.com [College of Materials Science and Engineering, Fuzhou University, New Campus, Minhou, Fujian Province 350108 (China)

    2014-09-30

    Highlights: • Dry desulfurization slag, solid waste, was an efficient adsorbent for lead removal. • The adsorption of Pb{sup 2+} onto dry desulfurization slag was generally monolayer. • The rate limiting step in the adsorption process of Pb{sup 2+} was chemisorption. • Pb{sup 2+} was absorbed onto the surface of the sample adsorbent only. • The adsorbent was low-cost and could be recycled. - Abstract: A collectable and non-sintered material prepared as hollow cylindrical shaped pellet from dry desulfurization slag (FGD ash) and ordinary Portland cement (OPC) for wastewater treatments is tested. The characteristic results of powder X-ray diffraction (XRD) and infrared absorption spectroscopy (IR) show that –OH, CO{sub 3}{sup 2−}, SO{sub 3}{sup 2−} and SO{sub 4}{sup 2−} are the possible functional groups responsible for Pb uptake. Adsorption data indicate that Pb removal is pH dependent and optimal at pH 6, with a very rapid initial removal that reaches equilibrium in about 90 min. A maximum removal of 99.2% is seen for 5 mg/L (pH of 6); higher initial Pb concentrations reduce overall removal efficiencies, but generate higher surface loadings. Adsorption process correlates well with both Langmuir and Freundlich models, although the Langmuir isotherm is more favored, providing a maximum adsorption capacity (Qm) of 130.2 mg/g (13 wt%). Pseudo-second order rate kinetic model best describes the Pb removal, and calculated R{sub L} values between 0 and 1, indicate a favored adsorption process that is chemisorption limited. SEM and EDAX analysis of the surface and fracture surface show that Pb occurs as surface precipitates and that Pb is not distributed to the inner core of the pellet. This study demonstrates that dry FGD ash could be successfully used for wastewater Pb removal.

  20. Efficient bounding schemes for the two-center hybrid flow shop scheduling problem with removal times.

    Science.gov (United States)

    Hidri, Lotfi; Gharbi, Anis; Louly, Mohamed Aly

    2014-01-01

    We focus on the two-center hybrid flow shop scheduling problem with identical parallel machines and removal times. The job removal time is the required duration to remove it from a machine after its processing. The objective is to minimize the maximum completion time (makespan). A heuristic and a lower bound are proposed for this NP-Hard problem. These procedures are based on the optimal solution of the parallel machine scheduling problem with release dates and delivery times. The heuristic is composed of two phases. The first one is a constructive phase in which an initial feasible solution is provided, while the second phase is an improvement one. Intensive computational experiments have been conducted to confirm the good performance of the proposed procedures.

  1. Lead and copper removal from aqueous solutions by porous glass derived calcium hydroxyapatite

    International Nuclear Information System (INIS)

    Liang Wen; Zhan Lei; Piao Longhua; Ruessel, Christian

    2011-01-01

    Graphical abstract: . Adsorption of Pb 2+ increases with the increase in NaCl volume percentage (1:0%, 2:30%, 3:40%, 4:40%) of the Glass Derived Hydroxyapatite and reaches equilibrium after 24 h. Highlights: → Novel porous glass derived hydroxyapatite matrix is prepared. → Glass derived hydroxyapatite matrix adsorbs lead and copper ions in solutions effectively. → Two adsorption mechanisms including ion exchange theory and the dissolution and precipitation theory are involved in removal of the heavy metal ions from the solutions. - Abstract: A porous glass was prepared by sintering Na 2 O-CaO-B 2 O 3 glass powder with powdered sodium chloride. Subsequently, the sodium chloride was dissolved in water resulting in a highly porous material. A sample was prepared consisting of 60 vol% glass and 40 vol% salt which both had particle sizes 2 HPO 4 solutions at room temperature for 1 day. The porous glass derived hydroxyapatite matrix was then processed for removing lead and copper ions from aqueous solutions. The results showed that the glass derived calcium hydroxyapatite matrix effectively immobilizes lead and copper ions in solution. The adsorption mechanism was investigated by the X-ray Diffraction (XRD) and Scanning Electron Microscopy including Energy Dispersive X-Ray Spectrometry (SEM-EDX).

  2. Predicting adsorptive removal of chlorophenol from aqueous solution using artificial intelligence based modeling approaches.

    Science.gov (United States)

    Singh, Kunwar P; Gupta, Shikha; Ojha, Priyanka; Rai, Premanjali

    2013-04-01

    The research aims to develop artificial intelligence (AI)-based model to predict the adsorptive removal of 2-chlorophenol (CP) in aqueous solution by coconut shell carbon (CSC) using four operational variables (pH of solution, adsorbate concentration, temperature, and contact time), and to investigate their effects on the adsorption process. Accordingly, based on a factorial design, 640 batch experiments were conducted. Nonlinearities in experimental data were checked using Brock-Dechert-Scheimkman (BDS) statistics. Five nonlinear models were constructed to predict the adsorptive removal of CP in aqueous solution by CSC using four variables as input. Performances of the constructed models were evaluated and compared using statistical criteria. BDS statistics revealed strong nonlinearity in experimental data. Performance of all the models constructed here was satisfactory. Radial basis function network (RBFN) and multilayer perceptron network (MLPN) models performed better than generalized regression neural network, support vector machines, and gene expression programming models. Sensitivity analysis revealed that the contact time had highest effect on adsorption followed by the solution pH, temperature, and CP concentration. The study concluded that all the models constructed here were capable of capturing the nonlinearity in data. A better generalization and predictive performance of RBFN and MLPN models suggested that these can be used to predict the adsorption of CP in aqueous solution using CSC.

  3. Removal of mercury ion from aqueous solution by activated carbons obtained from biomass and coals

    Energy Technology Data Exchange (ETDEWEB)

    Ekinci, E.; Yardim, F. [Faculty of Chemical Engineering, Istanbul Technical University, Ayazaga, 80626 Istanbul (Turkey); Budinova, T.; Petrov, N.; Razvigorova, M.; Minkova, V. [Institute of Organic Chemistry, Bulgarian Academy of Sciences, Acad.G.Bonchev, str. bl. 9, Sofia (Bulgaria)

    2002-06-20

    The adsorption of Hg(II) from aqueous solution at 293 K by activated carbons obtained from apricot stones, furfural and coals was studied. Adsorption studies were performed under the varying conditions of time of treatment, metal ion concentration and pH. The process of adsorption followed Langmuir isotherm. The removal of Hg(II) increased with the increase of pH of the solution from 2 to 5 and remained constant up to pH 10. Desorption studies were preformed.

  4. Uranium removal from acidic aqueous solutions by Saccharomyces cerevisiae, Debaryomyces hansenii, Kluyveromyces marxianus and Candida colliculosa

    International Nuclear Information System (INIS)

    Sarri, S.; Misaelides, P.; Papanikolaou, M.; Zamboulis, D.

    2009-01-01

    The sorption of uranium from acidic aqueous solutions (pH 4.5, C init = 10 to 1000 mg U/L) by Saccharomyces cerevisiae, Debaryomyces hansenii, Kluyveromyces marxianus and Candida colliculosa was investigated using a batch technique. The U-sorption onto Saccharomyces cerevisiae and Debaryomyces hansenii followed a Langmuir, while that onto Kluyveromyces marxianus and Candida colliculosa a Freundlich isotherm. The results demonstrated that all investigated biomasses could effectively remove uranium from acidic aqueous solutions. From all sorbents, Saccharomyces cerevisiae appeared to be the most effective with a maximum sorption capacity of 127.7 mg U/g dry biomass. (author)

  5. Selection of the Best Process Stream to Remove Ca2+ Ion Using Electrodialysis from Sugar Solution

    Directory of Open Access Journals (Sweden)

    Jogi Ganesh Dattatreya Tadimeti

    2014-01-01

    Full Text Available Electrodialytic removal of calcium chloride (CaCl2, 25–50 mol·m−3 from 5% sugar solution was executed in batch recirculation mode. Calcium ion removal rate was monitored with (i applied potential, (ii feed flow rate, (iii solution viscosity and conductivity, and (iv catholyte streams (NaOH or sodium salt of ethylene diamine tetraacetic acid-acetic acid, Na2EDTA-AA. Unsteady state model for ion concentration change was written for the ED cell used. Linearized Nernst-Planck equation instead of Ohm’s law was applied to closely obtain the current density and concentration change theoretically. The model developed could closely predict the experimental observation. Mass transfer coefficients and specific energy densities were estimated for each combination of catholyte stream used. NaOH showed better performance for a short duration over Na2EDTA-acetic acid combination.

  6. Removal of Indigo Carmine Dye from Aqueous Solution Using Magnesium Hydroxide as an Adsorbent

    Directory of Open Access Journals (Sweden)

    Thimmasandra Narayan Ramesh

    2015-01-01

    Full Text Available Magnesium hydroxide is used as an adsorbent for the removal of indigo carmine dye from aqueous solution. We have investigated the effectiveness of removal of indigo carmine dye from aqueous solutions at pH 6-7 and 12-13 using magnesium hydroxide thereby varying the dose of the adsorbent, concentration of the dye, duration, and temperature. Structural transformations of adsorbent during the adsorption process at different pH values are monitored using powder X-ray diffraction and infrared spectroscopy. Different types of adsorption isotherm models were evaluated and it was found that Langmuir isotherm fits well at both pH values (6-7 and 12-13. Adsorption of indigo carmine onto magnesium hydroxide at pH 6-7/pH 12-13 follows pseudo-second order rate kinetics.

  7. Color removal from acid and reactive dye solutions by electrocoagulation and electrocoagulation/adsorption processes.

    Science.gov (United States)

    Bellebia, S; Kacha, S; Bouberka, Z; Bouyakoub, A Z; Derriche, Z

    2009-04-01

    In this study, electrocoagulation of Marine Blue Erionyl MR (acid dye) and electrocoagulation followed by adsorption of Brilliant Blue Levafix E-BRA (reactive dye) from aqueous solutions were investigated, using aluminum electrodes and granular activated carbon (GAC). In the electrocoagulation and adsorption of dyestuff solutions, the effects of current density, loading charge, pH, conductivity, stirring velocity, contact time, and GAC concentration were examined. The optimum conditions for the electrocoagulation process were identified as loading charges 7.46 and 1.49 F/m3, for a maximum abatement of 200 mg/L reactive and acid dye, respectively. The residual reactive dye concentration was completely removed with 700 mg/L GAC. The results of this investigation provide important data for the development of a combined process to remove significant concentrations of recalcitrant dyes from water, using moderate activated carbon energy and aluminum consumption, and thereby lowering the cost of treatment.

  8. Chemical activation of tea waste and use for the removal of chromium (Vi) from aqueous solution

    International Nuclear Information System (INIS)

    Qureshi, K.; Bhatti, I.; Ansari, A.K.

    2009-01-01

    Tea waste is the residue left after the preparation of tea. At present the tea waste is regarded as a waste product having no use. In this study, tea waste is converted into an adsorbent. Tea waste is chemically activated with phosphoric acid at low temperature 450 degree C. This activated carbon is then utilized as an adsorbent for the removal of Chromium (VI) from aqueous solution. The various sorption parameters i.e pH, sorbent dose sorbate concentration, shaking time and shaking speed are first optimized. 75% of chromium from aqueous solution is effectively removed at pH 2. The best optimum conditions were obtained when 1 gm of sorbent was agitated at 100 rpm with 60 mg/l of sorbate for 50 minutes. Better results were obtained when low concentrations of sorbates were used. Hence tea waste could also be successfully used for the sorption of Chromium (VI), from industrial waste water. (author)

  9. Thin Film Packaging Solutions for High Efficiency OLED Lighting Products

    Energy Technology Data Exchange (ETDEWEB)

    None

    2008-06-30

    The objective of the 'Thin Film Packaging Solutions for High Efficiency OLED Lighting Products' project is to demonstrate thin film packaging solutions based on SiC hermetic coatings that, when applied to glass and plastic substrates, support OLED lighting devices by providing longer life with greater efficiency at lower cost than is currently available. Phase I Objective: Demonstrate thin film encapsulated working phosphorescent OLED devices on optical glass with lifetime of 1,000 hour life, CRI greater than 75, and 15 lm/W. Phase II Objective: Demonstrate thin film encapsulated working phosphorescent OLED devices on plastic or glass composite with 25 lm/W, 5,000 hours life, and CRI greater than 80. Phase III Objective: Demonstrate 2 x 2 ft{sup 2} thin film encapsulated working phosphorescent OLED with 40 lm/W, 10,000 hour life, and CRI greater than 85. This report details the efforts of Phase III (Budget Period Three), a fourteen month collaborative effort that focused on optimization of high-efficiency phosphorescent OLED devices and thin-film encapsulation of said devices. The report further details the conclusions and recommendations of the project team that have foundation in all three budget periods for the program. During the conduct of the Thin Film Packaging Solutions for High Efficiency OLED Lighting Products program, including budget period three, the project team completed and delivered the following achievements: (1) a three-year marketing effort that characterized the near-term and longer-term OLED market, identified customer and consumer lighting needs, and suggested prototype product concepts and niche OLED applications lighting that will give rise to broader market acceptance as a source for wide area illumination and energy conservation; (2) a thin film encapsulation technology with a lifetime of nearly 15,000 hours, tested by calcium coupons, while stored at 16 C and 40% relative humidity ('RH'). This encapsulation technology

  10. Removal of radioruthenium from alkaline intermediate level radioactive waste solution : a laboratory investigation

    International Nuclear Information System (INIS)

    Samanta, S.K.; Theyyunni, T.K.

    1994-01-01

    Various methods were investigated in the laboratory for the removal of radioruthenium from alkaline intermediate level radioactive waste solutions of reprocessing plant origin. The methods included batch equilibration with different ion exchangers and sorbents, column testing and chemical precipitation. A column method using zinc-activated carbon mixture and a chemical precipitation method using ferrous salt along with sodium sulphite were found to be promising for plant scale application. (author). 10 refs., 3 figs., 7 tabs

  11. Removal of metallic ions from aqueous solutions by fluidized bed fly ashes

    Energy Technology Data Exchange (ETDEWEB)

    Rio, S.; Delebarre, A.; Hequet, V. [Ecole des Mines de Nantes, 44 - Nantes (France); Blondin, J. [Cerchar 62 - Mazingarbe (France)

    2001-07-01

    One of the main constraints deriving from the generation of power by coal combustion is to find some use for the fly ashes instead of disposing of them. Fly ashes from two fluidized bed power plants were tested to remove Pb{sup 2+}, Cu{sup 2+}, Cr (III), Ni{sup 2+}, Zn{sup 2+} and Cr (VI) from aqueous solutions. Experimental design methodology was used to study the removal and the leaching as a function of (i) the water pollutant content, (ii) the metal concentration in water, (iii) the pH of the solution and (iv) the addition of lime to fly ashes. The results show that the percentage of adsorbed ions was more important when they were in contact with silico-aluminous fly ashes than sulfo-calcic fly ashes, except in the case of the ion Ni{sup 2+}. The removal of metallic ions increases with increasing pH. The metallic canons removal accounting for the leaching test was higher when lime was added to silico-aluminous fly ashes during the adsorption. (authors)

  12. Removal of mercury from aqueous solutions using activated carbon prepared from agricultural by-product/waste.

    Science.gov (United States)

    Rao, M Madhava; Reddy, D H K Kumar; Venkateswarlu, Padala; Seshaiah, K

    2009-01-01

    Removal of mercury from aqueous solutions using activated carbon prepared from Ceiba pentandra hulls, Phaseolus aureus hulls and Cicer arietinum waste was investigated. The influence of various parameters such as effect of pH, contact time, initial metal ion concentration and adsorbent dose for the removal of mercury was studied using a batch process. The experiments demonstrated that the adsorption process corresponds to the pseudo-second-order-kinetic models and the equilibrium adsorption data fit the Freundlich isotherm model well. The prepared adsorbents ACCPH, ACPAH and ACCAW had removal capacities of 25.88 mg/g, 23.66 mg/g and 22.88 mg/g, respectively, at an initial Hg(II) concentration of 40 mg/L. The order of Hg(II) removal capacities of these three adsorbents was ACCPH>ACPAH>ACCAW. The adsorption behavior of the activated carbon is explained on the basis of its chemical nature. The feasibility of regeneration of spent activated carbon adsorbents for recovery of Hg(II) and reuse of the adsorbent was determined using HCl solution.

  13. Removal of heavy metals from aqueous solution by nonliving Ulva seaweed as biosorbent.

    Science.gov (United States)

    Suzuki, Yoshihiro; Kametani, Takuji; Maruyama, Toshiroh

    2005-05-01

    The growth of dense green seaweed mats of Ulva spp. is an increasing problem in estuaries and coasts worldwide. The enormous amount of Ulva biomass thus becomes a troublesome waste disposal problem. On the other hand, it has been revealed that nonliving seaweed biomass, particularly brown seaweeds, has a high capacity for assimilating heavy metals. In this study, the possibility of using Ulva seaweed biomass as a biosorbent for the removal of heavy metals was examined. After processing, the biomass material was very easy to separate from the aqueous solution using a mesh. The sorption capacity of Cd on Ulva biomass increased upon pretreatment with alkali solution. The outstanding function of the biosorbent was demonstrated at around pH 8. On the basis of the Langmuir isotherms of Cd, Zn and Cu using the alkali-pretreated biomass, the parameters q(m) and b were determined to be within the narrow range of 60-90 mg/g and 0.03-0.04 L/mg, respectively, for each metal. Given the q(m) and b values, Ulva seaweed is a good biosorbent material for removing heavy metals. In an experiment using artificial wastewater containing Cd, Zn, Cu, Cr and Ni, it was possible to remove each metal simultaneously using Ulva biomass. Adsorption by Ulva biomass is effective for the removal of heavy metals from wastewater.

  14. Removal of Reactive Anionic Dyes from Binary Solutions by Adsorption onto Quaternized Kenaf Core Fiber

    Directory of Open Access Journals (Sweden)

    Intidhar Jabir Idan

    2017-01-01

    Full Text Available The most challenging mission in wastewater treatment plants is the removal of anionic dyes, because they are water-soluble and produce very shining colours in the water. In this regard, kenaf core fiber (KCF was chemically modified by the quaternized agent (3-chloro-2-hydroxypropyltrimethylammonium chloride to increase surface area and change the surface properties in order to improve the removing reactive anionic dyes from binary aqueous solution. The influencing operating factors like dye concentration, pH, adsorbent dosage, and contact time were examined in a batch mode. The results indicate that the percentage of removal of Reactive Red-RB (RR-RB and Reactive Black-5 (RB-5 dyes from binary solution was increased with increasing dyes concentrations and the maximum percentage of removal reached up to 98.4% and 99.9% for RR-RB and RB-5, respectively. Studies on effect of pH showed that the adsorption was not significantly influenced by pH. The equilibrium analyses explain that, in spite of the extended Langmuir model failure to describe the data in the binary system, it is better than the Jain and Snoeyink model in describing the adsorption behavior of binary dyes onto QKCF. Also, the pseudo-second-order model was better to represent the adsorption kinetics for RR-RB and RB-5 dyes on QKCF.

  15. Study on removing nitrate from uranium solution by ion-exchange method

    International Nuclear Information System (INIS)

    Zhou Genmao

    2004-01-01

    Nitrate of low concentration can interfere with adsorption of uranyl sulfate anion on anion-exchange resins because the anion-exchange resins have a stronger affinity for nitrate in uranium solution. Nitrate can be adsorbed with a high efficiency resin, then desorbed by sodium hydroxide. The nitrate concentration is about 60 g/L in eluate. The research results show that nitrate can be recovered from uranium solution with N-3 anion-exchange resin

  16. Chitosan scaffold as an alternative adsorbent for the removal of hazardous food dyes from aqueous solutions.

    Science.gov (United States)

    Esquerdo, V M; Cadaval, T R S; Dotto, G L; Pinto, L A A

    2014-06-15

    The dye adsorption with chitosan is considered an eco-friendly alternative technology in relation to the existing water treatment technologies. However, the application of chitosan for dyes removal is limited, due to its low surface area and porosity. Then we prepared a chitosan scaffold with a megaporous structure as an alternative adsorbent to remove food dyes from solutions. The chitosan scaffold was characterized by infrared spectroscopy, scanning electron microscopy and structural characteristics. The potential of chitosan scaffold to remove five food dyes from solutions was investigated by equilibrium isotherms and thermodynamic study. The scaffold-dyes interactions were elucidated, and desorption studies were carried out. The chitosan scaffold presented pore sizes from 50 to 200 μm, porosity of 92.2±1.2% and specific surface area of 1135±2 m(2) g(-1). The two-step Langmuir model was suitable to represent the equilibrium data. The adsorption was spontaneous, favorable, exothermic and enthalpy-controlled process. Electrostatic interactions occurred between chitosan scaffold and dyes. Desorption was possible with NaOH solution (0.10 mol L(-1)). The chitosan megaporous scaffold showed good structural characteristics and high adsorption capacities (788-3316 mg g(-1)). Copyright © 2014 Elsevier Inc. All rights reserved.

  17. Poly(acrylamide) functionalized chitosan: An efficient adsorbent for azo dyes from aqueous solutions

    International Nuclear Information System (INIS)

    Singh, Vandana; Sharma, Ajit Kumar; Sanghi, Rashmi

    2009-01-01

    In the present communication we report on the optimization of persulfate/ascorbic acid initiated synthesis of chitosan-graft-poly(acrylamide) (Ch-g-PAM) and its application in the removal of azo dyes. The optimum yield of the copolymer was obtained using 16 x 10 -2 M acrylamide, 3.0 x 10 -2 M ascorbic acid, 2.4 x 10 -3 M K 2 S 2 O 8 and 0.1 g chitosan in 25 mL of 5% aqueous formic acid at 45 ± 0.2 o C. Ch-g-PAM remained water insoluble even under highly acidic conditions and could efficiently remove Remazol violet and Procion yellow dyes from the aqueous solutions over a pH range of 3-8 in contrast to chitosan (Ch) which showed pH dependent adsorption. The adsorption data of the Ch-g-PAM and Ch for both the dyes were modeled by Langmuir and Freundlich isotherms where the data fitted better to Langmuir isotherms. To understand the adsorption behavior of Ch-g-PAM, adsorption of Remazol violet on to the copolymer was optimized and the kinetic and thermodynamic studies were carried out taking Ch as reference. Both Ch-g-PAM and Ch followed pseudo-second-order adsorption kinetics. The thermodynamic study revealed a positive heat of adsorption (ΔH o ), a positive ΔS o and a negative ΔG o , indicating spontaneous and endothermic nature of the adsorption of RV dye on to the Ch-g-PAM. The Ch-g-PAM was found to be very efficient in removing color from real industrial wastewater as well, though the interfering ions present in the wastewater slightly hindered its adsorption capacity. The data from regeneration efficiencies for ten cycles evidenced the high reusability of the copolymer in the treatment of waste water laden with even high concentrations of dye.

  18. Organic Removal Efficiency of the Nanofiltration and Adsorption Hybrid System in High Strength Wastewater

    Directory of Open Access Journals (Sweden)

    Amir Hessam Hassani

    2011-03-01

    Full Text Available Surface and groundwater resources are increasingly jeopardized by discharges from pharmaceutical, chemical, and detergent plants. The high pollutant load of the effluents from these industries requires specific treatments. The objective of this research was to study and compare the nanofiltration and adsorption hybrid system with the plain nanofiltration system in wastewater treatment.For this purpose, a pilot nanofiltration system with a capacity of 7.6 m3/d using 1 and 5 micron filters and a FILMTEC NF90-4040 membrane was used in the first phase of the study. In the second phase, granular activated carbon cartridges were used. Inluent and effluent discharges as well as the COD removal were measured in both systems under variable times and organic load conditions. The results showed that COD removal efficiency was higher in the hybrid system than in the plain naonofiltration one. In the hybrid system, the Maximum in the hybrid system, the COD removal efficiencies achieved for organic loads of 1000, 2000, and 3000 mg/L were 99%, 95.86%, and 92.93%, respectively. The same values for the plain nanofiltration system were 87.34%, 50%, and 29.41%, respectively. It was found that polarization and membrane fouling decreased both the effluent flow and the COD removal efficiency with time. Fouling of the membrane was, however, lower in the hybrid system compared to the plain nanofiltration; thus, the hybrid system was associated with higher values of COD removal and delayed membrane fouling.

  19. Influence of SiO2 and graphene oxide nanoparticles on efficiency of biological removal process.

    Science.gov (United States)

    Esmaeili-Faraj, Seyyed Hamid; Nasr Esfahany, Mohsen

    2017-11-01

    The effects of the presence of synthesized silica (SS) and exfoliated graphene oxide (EGO) on the removal of sulfide ion with activated sludge (AS) are experimentally investigated. The maximum removal efficiency of sulfide ion for AS without nanoparticles, and the samples with SS and EGO nanoparticles were 81%, 88% and 79%, respectively. Moreover, the maximum elimination capacity (EC max ) for the bioreactor with SS-nanoparticles is 7542 mg/L s, while the EC max of AS and EGO samples were 7075 and 6625 mg/L s, respectively. Two filamentous microbial strains as Gram-negative and Gram-positive bacteria are discerned that removed sulfide ion in the presence of nanoparticles. The measurement of mixture liquor volatile suspended solid that indicates the biomass growth rate during the test shows that the bioreactor containing SS-nanoparticles has more biomass content than the other samples. Our findings indicate that SS-nanoparticles with 0.1% wt. concentration in the bioreactor have no negative effects on the efficiency of the biological removal of sulfide and the presence of SS-nanoparticles even enhances the performance of the bioreactor. On the other side, a bioreactor with EGO nanosheets, as highly antibacterial nanoparticles, with 0.02% wt. concentration significantly influences the microbial growth and reduces sulfide removal efficiency.

  20. Efficiency of a Photoreactor Packed with Immobilized Titanium Dioxide Nanoparticles in the Removal of Acid Orange 7.

    Science.gov (United States)

    Sheidaei, Behnaz; Behnajady, Mohammad A

    2016-05-01

    In this paper, the removal efficiency of Color Index Acid Orange 7 (AO7) as a model contaminant was investigated in a batch-recirculated photoreactor packed with immobilized titanium dioxide type P25 nanoparticles on glass beads. The effects of different operational parameters such as the initial concentration of AO7, the volume of solution, the volumetric flowrate, and the light source power in the photoreactor were investigated. The results indicate that the removal percent increased with the rise in volumetric flowrate and power of the light source, but decreased with the rise of the initial concentration of AO7 and the volume of solution. The AO7 degradation was followed through total organic carbon, gas chromatography/mass spectroscopy (GC/MS), and mineralization products analysis. The ammonium and sulfate ions were analyzed as mineralization products of nitrogen and sulfur heteroatoms, respectively. The results of GC/MS revealed the production of 1-indanone, 1-phthalanone, and 2-naphthalenol as intermediate products for the removal of AO7 in this process.

  1. Simultaneous treatment of chlorinated organics and removal of metals and radionuclides with bimetals and complexing acids - application to surfactant solutions

    Energy Technology Data Exchange (ETDEWEB)

    Korte, N.E.; Gu, B. [Oak Ridge National Lab., TN (United States)

    1997-10-01

    Currently available methods for separation and treatment of radioactive mixed waste are typically energy-intensive, and often require high temperatures. Passive methods that operate at ambient temperatures are needed. The purpose of this task is to develop bimetallic substrates, using a base metal such as iron and a promoter metal such as palladium (Pd), to provide a passive, low-energy solution to a substantial portion of DOE`s mixed-waste problem. This technology consists of a porous medium that can simultaneously dechlorinate hazardous organics such as TCE and polychlorinated biphenyls (PCBs) at the same time that it