[Significance of extruded feeds for trout nutrition and water protection].

Science.gov (United States)

Steffens, W

1993-01-01

Extruded feeds exhibit an improved starch digestibility and are more firmly bound due to the almost complete gelatinization of the starch. This results in fewer fines and longer water stability than pelleted feeds. Extruded pellets also have the advantage that they can soak up more oil than a conventional pellet. It is therefore possible to increase the maximum oil content to more than 20%. On the other hand extruding feeds is more expensive than steam pelleting. Gelatinized starch is a useful energy source in trout diets helping to reduce feed conversion ratios. Proportions up to 35-40% in the diet are tolerable. Using high dietary levels of both gelatinized starch and oil the non-protein energy of feed may be increased and thus a protein-sparing effect results. High-energy diets enable to reduce excretion of faeces and of nitrogen via gills. In addition a decrease of phosphorus level in feeds and thus of phosphorus excretion by fish is possible. Extruded high-energy diets therefore make a contribution to improve water quality.

Enzymatic hydrolysis of starch in the presence of cereal soluble fibre polysaccharides.

Science.gov (United States)

Dhital, Sushil; Dolan, Grace; Stokes, Jason R; Gidley, Michael J

2014-03-01

The in vitro amylolysis of both granular and cooked maize starch and the diffusion of glucose in the presence of 1% and 2% cereal soluble fibre polysaccharides (arabinoxylan and mixed linkage beta-glucan) were studied at various levels of shear mixing in order to identify potential molecular mechanisms underlying observed glycemia-reducing effects of soluble fibres in vivo. The presence of soluble fibres increased viscosity by ca. 10× and 100× for 1% and 2% concentrations respectively. Despite this large difference in viscosity, measured digestion and mass transfer coefficients were only reduced by a factor of 1.5 to 2.5 at the same mixing speed. In contrast, introduction of mixing in the digesting and diffusing medium significantly increased the rate of amylolytic starch digestion and mass transfer of glucose. This effect is such that mixing at high speeds negates the hindering effect of the 100× increased viscosity imparted by the presence of 2% soluble fibre; this is essentially captured by the Reynolds number (the ratio of inertial and viscous forces) that defines the flow kinematics. The modest reduction of in vitro starch hydrolysis and glucose diffusion at increased viscosity suggests that the established benefits of soluble fibres on post-prandial glycaemia, in terms of attenuation of the overall rate and extent of dietary starch conversion to blood glucose, are not primarily due to a direct effect of viscosity. Alternative hypotheses are proposed based on gastric emptying, restriction of turbulent flow, and/or stimulation of mucus turnover.

Effect of extrusion cooking on the functional properties and starch components of lentil/banana blends: Response surface analysis

OpenAIRE

Hernández-Nava, R.G.; Bello-Pérez, L.A.; San Martín-Martínez, E.; Hernández-Sánchez, H.; Mora-Escobedo, R.

2011-01-01

Banana and lentil flour blends were processed in a sing le screw extruder modifying the flour properties of the blend (20.5-79.5%), at selected range of die temperature (145-175 ºC) and the feeding moisture content (20-24%). Functional characteristics evaluated in the extrudates were water absorption index (WAI), water solubility index (WSI), bulk density (BD), paste viscosity properties, microstructure and resistant starch content. The concentration of lentil/banana blends and temperature we...

Chemically Modified Starch; Allyl- and Epoxy-Starch Derivatives: Their Synthesis and Characterization

NARCIS (Netherlands)

Franssen, M.C.R.; Boeriu, C.

2014-01-01

Both native and modified starches, such as starch that is pregelatinized, extruded, acid-converted, cross-linked, and substituted, are widely used in industry. This chapter describes a mild two-step process for the synthesis of novel, highly reactive granular epoxy-starch derivatives. Via this

Biomimetic synthesis of calcium carbonate with different morphologies and polymorphs in the presence of bovine serum albumin and soluble starch.

Science.gov (United States)

Liu, Yuxi; Chen, Yuping; Huang, Xuechen; Wu, Gang

2017-10-01

Calcium carbonate has been synthesized by the reaction of Na 2 CO 3 and CaCl 2 in the presence of bovine serum albumin (BSA) and soluble starch. Effects of various bovine serum albumin (BSA) and soluble starch on the polymorph and morphology of CaCO 3 crystals were investigated. Crystallization of vaterite is favored in the presence of BSA and soluble starch, respectively, while calcite is favored in the presence of a mixture of BSA and soluble starch. The morphologies of CaCO 3 particles in the presence of mixture of BSA and soluble starch are mainly rod-like, suggesting that the BSA, soluble and their assemblies play key roles in stabilizing and directing the CaCO 3 crystal growth. Copyright © 2017. Published by Elsevier B.V.

Extrusion induced low-order starch matrices: Enzymic hydrolysis and structure.

Science.gov (United States)

Zhang, Bin; Dhital, Sushil; Flanagan, Bernadine M; Luckman, Paul; Halley, Peter J; Gidley, Michael J

2015-12-10

Waxy, normal and highwaymen maize starches were extruded with water as sole plasticizer to achieve low-order starch matrices. Of the three starches, we found that only high-amylose extrudate showed lower digestion rate/extent than starches cooked in excess water. The ordered structure of high-amylose starches in cooked and extruded forms was similar, as judged by NMR, XRD and DSC techniques, but enzyme resistance was much greater for extruded forms. Size exclusion chromatography suggested that longer chains were involved in enzyme resistance. We propose that the local molecular density of packing of amylose chains can control the digestion kinetics rather than just crystallinity, with the principle being that density sufficient to either prevent/limit binding and/or slow down catalysis can be achieved by dense amorphous packing. Copyright © 2015 Elsevier Ltd. All rights reserved.

Chemical Methods for the Determination of Soluble and Insoluble Non-Starch Polysaccharides - Review

Directory of Open Access Journals (Sweden)

Rodica Căpriţă

2011-10-01

Full Text Available Polysaccharides are macromolecules of monosaccharides linked by glycosidic bonds. Non-starch polysaccharides(NSP are principally non-α-glucan polysaccharides of the plant cell wall. They are a heterogeneous group ofpolysaccharides with varying degrees of water solubility, size, and structure. The water insoluble fiber fractioninclude cellulose, galactomannans, xylans, xyloglucans, and lignin, while the water-soluble fibers are the pectins,arabinogalactans, arabinoxylans, and β-(1,3(1,4-D-glucans (β-glucans. Both the enzymatic-gravimetric andenzymatic-chemical methods used for the determination of soluble and insoluble non-starch polysaccharides haveundergone a number of modifications and improvements, most occurring over the last 20 years.

Replacement of traditional seawater-soluble pigments by starch and hydrolytic enzymes in polishing antifouling coatings

DEFF Research Database (Denmark)

Olsen, Søren Martin; Pedersen, L. T.; Dam-Johansen, Kim

2010-01-01

The use of starch and hydrolytic enzymes as replacement for traditional polishing pigments (e.g., Cu2O and ZnO) in antifouling coatings has been investigated. The enzymes facilitate a slow conversion of water-insoluble starch into water-soluble glucose, and dissolution of glucose causes the devel......The use of starch and hydrolytic enzymes as replacement for traditional polishing pigments (e.g., Cu2O and ZnO) in antifouling coatings has been investigated. The enzymes facilitate a slow conversion of water-insoluble starch into water-soluble glucose, and dissolution of glucose causes...... the development of a leached (porous) layer in the wetted, outermost part of the coating. Subsequent water-binder interaction at the pore walls gives rise to polishing, in a manner similar to that of conventional antifouling coatings. Different starch types have been evaluated and classified as potential coating...

Cofortification of ferric pyrophosphate and citric acid/trisodium citrate into extruded rice grains doubles iron bioavailability through in situ generation of soluble ferric pyrophosphate citrate complexes.

Science.gov (United States)

Hackl, Laura; Cercamondi, Colin I; Zeder, Christophe; Wild, Daniela; Adelmann, Horst; Zimmermann, Michael B; Moretti, Diego

2016-05-01

Iron fortification of rice is a promising strategy for improving iron nutrition. However, it is technically challenging because rice is consumed as intact grains, and ferric pyrophosphate (FePP), which is usually used for rice fortification, has low bioavailability. We investigated whether the addition of a citric acid/trisodium citrate (CA/TSC) mixture before extrusion increases iron absorption in humans from FePP-fortified extruded rice grains. We conducted an iron absorption study in iron-sufficient young women (n = 20), in which each participant consumed 4 different meals (4 mg Fe/meal): 1) extruded FePP-fortified rice (No CA/TSC); 2) extruded FePP-fortified rice with CA/TSC added before extrusion (CA/TSC extruded); 3) extruded FePP-fortified rice with CA/TSC solution added after cooking and before consumption (CA/TSC solution); and 4) nonextruded rice fortified with a FeSO4 solution added after cooking and before consumption (reference). Iron absorption was calculated from erythrocyte incorporation of stable iron isotopes 14 d after administration. In in vitro experiments, we assessed the soluble and dialyzable iron from rice meals in which CA/TSC was added at different preparation stages and from meals with different iron:CA:TSC ratios. Fractional iron absorption was significantly higher from CA/TSC-extruded meals (3.2%) than from No CA/TSC (1.7%) and CA/TSC solution (1.7%; all P solubility and dialyzability were higher in CA/TSC-extruded rice than in rice with No CA/TSC and CA/TSC solution, and solubility increased with higher amounts of added CA and TSC in extruded rice. Iron bioavailability nearly doubled when CA/TSC was extruded with FePP into fortified rice, resulting in iron bioavailability comparable to that of FeSO4 We attribute this effect to an in situ generation of soluble FePP citrate moieties during extrusion and/or cooking because of the close physical proximity of FePP and CA/TSC in the extruded rice matrix. This trial was registered at

Cariogenicity of soluble starch in oral in vitro biofilm and experimental rat caries studies: a comparison.

Science.gov (United States)

Thurnheer, T; Giertsen, E; Gmür, R; Guggenheim, B

2008-09-01

Common belief suggests that starch is less cariogenic than sugar; however, the related literature is quite controversial. We aimed to compare cariogenic and microbiological effects of soluble starch in both a standard animal model and an oral biofilm system, and to assess the possible substitution of the animal model. Six-species biofilms were grown anaerobically on enamel discs in saliva and medium with glucose/sucrose, starch (average molecular weight of 5000, average polymerization grade of 31), or mixtures thereof. After 64.5 h of biofilm formation, the microbiota were quantitated by cultivation and demineralization was measured by quantitative light-induced fluorescence. To assess caries incidence in rats, the same microbiota as in the biofilm experiments were applied. The animals were fed diets containing either glucose, glucose/sucrose, glucose/sucrose/starch or starch alone. Results with both models show that demineralization was significantly smaller with starch than sucrose. The data demonstrate that soluble starch is substantially less cariogenic than glucose/sucrose. By leading to the same scientific evidence as its in vivo counterpart, the described in vitro biofilm system provides an interesting and valuable tool in the quest to reduce experimentation with animals.

Acceptability and characterization of extruded pinto, navy and black beans.

Science.gov (United States)

Simons, Courtney W; Hall, Clifford; Tulbek, Mehmet; Mendis, Mihiri; Heck, Taylor; Ogunyemi, Samuel

2015-08-30

Consumption of dry beans has been relatively flat over the last decade. Creating new bean products may increase the consumption of beans and allow more consumers to obtain the health benefits of beans. In this study, pinto, navy and black beans were milled and the resulting flours extruded into puffs. Unflavored extruded puffs were evaluated by untrained panelists using a hedonic scale for appearance, flavor, texture and overall acceptability. The compositions of raw flours and extrudates were characterized. Sensory results indicated that all beans met or exceeded the minimum requirement for acceptability. Overall acceptability of navy and pinto beans was not significantly different, while acceptability of black bean puffs was significantly lower. Total protein (198-217 g kg(-1)) in extrudates was significantly different among the three beans. Total starch ranged from 398 to 406 g kg(-1) and was not significantly different. Resistant starch, total extractable lipid and raffinose contents were significantly reduced by extrusion. Extrusion did not affect crude fiber and phytic acid contents. The minimal effects on protein and fiber contents, the significant reduction in raffinose content and the acceptability of the unflavored extruded puffs support using various bean flours as ingredients in extruded puffed products. © 2014 Society of Chemical Industry.

The influence of starch molecular mass on the properties of extruded thermoplastic starch

NARCIS (Netherlands)

Vliegenthart, J.F.G.; Soest, J.J.G. van; Benes, K.; Wit, D. de

1996-01-01

The mechanical properties of a low and a high molecular mass thermoplastic starch (TPS) were monitored at water contents in the range of 5–30% (w/w). The granular starches were plasticized by extrusion processing with glycerol and water. The low molecular mass starch was prepared by partial acid

Properties of extruded snacks supplemented with amaranth grain grits

Directory of Open Access Journals (Sweden)

Hadnađev Miroslav S.

2009-01-01

Full Text Available Extruded amaranth grain products have specific aroma and can be used as snack food, supplement in breakfast cereals, or as raw material for further processing. Extruded products of corn-amaranth grits blends, containing 20% or 50% amaranth grain grits, were produced by extrusion-cooking using a laboratory Brabender single screw extruder 20 DN. Extrudates with various texture were obtained. During extrusion process starch granules are partially degraded, hence rheological properties were examined. All samples exhibited thixotropic flow behavior. Those samples in which part of the corn grits was replaced with amaranth one had lower viscosity and exhibited lower level of structuration during storage.

Modificação química e física do amido de quirera de arroz para aproveitamento na indústria de alimentos Chemical and physical modification of broken rice starch (Oryza sativa L. for use in food industry

Directory of Open Access Journals (Sweden)

Valéria Maria Limberger

2008-01-01

Full Text Available The study evaluated the efficiency of chemical (phosphorylation and physical (extrusion modifications of the starch of broken rice. Results demonstrated a reduction in the moisture content of extruded and phosphorylated broken rice and an increase in the ash content of phosphorylated broken rice. Both phosphorylation and extrusion increased cold water binding capacity, swelling power, and solubility. Extruded and phosphorylated pastes were stable under refrigeration, but only extruded paste was stable when submitted to freezing. Phosphorylated paste had the lowest viscosity and the highest stability during heating, while the extruded one gelatinized without heating, but had higher losses during heating.

Chemical Methods for the Determination of Soluble and Insoluble Non-Starch Polysaccharides - Review

OpenAIRE

Rodica Căpriţă; Adrian Căpriţă

2011-01-01

Polysaccharides are macromolecules of monosaccharides linked by glycosidic bonds. Non-starch polysaccharides(NSP) are principally non-α-glucan polysaccharides of the plant cell wall. They are a heterogeneous group ofpolysaccharides with varying degrees of water solubility, size, and structure. The water insoluble fiber fractioninclude cellulose, galactomannans, xylans, xyloglucans, and lignin, while the water-soluble fibers are the pectins,arabinogalactans, arabinoxylans, and β-(1,3)(1,4)-D-g...

Characterization of magnetic soluble starch-functionalized carbon nanotubes and its application for the adsorption of the dyes

International Nuclear Information System (INIS)

Chang, Peter R.; Zheng Pengwu; Liu Baoxiang; Anderson, Debbie P.; Yu Jiugao; Ma Xiaofei

2011-01-01

Soluble starch-functionalized multiwall carbon nanotube composites (MWCNT-starch) were prepared to improve the hydrophilicity and biocompatibility of MWCNTs. Characterization of the MWCNT-starch by Fourier transform infrared (FTIR) spectroscopy, ultraviolet-visible (UV-vis) spectroscopy, X-ray diffraction (XRD), transmission electron microscope (TEM) and thermogravimetric analysis (TG), showed that the starch component (about 14.3 wt%) was covalently grafted onto the surface of MWCNT. MWCNT-starch-iron oxide composites, intended for use as adsorbents for the removal of dyes from aqueous solutions, were prepared by synthesizing iron oxide nanoparticles at the surface of MWCNT-starch. Starch acts as a template for growth of iron oxide nanoparticles which are uniformly dispersed on the surface of the MWCNT-starch. MWCNT-starch-iron oxide exhibits superparamagnetic properties with a saturation magnetization (23.15 emu/g) and better adsorption for anionic methyl orange (MO) and cationic methylene blue (MB) dyes than MWCNT-iron oxide.

Properties of extrudates from sorghum varieties | Byaruhanga ...

African Journals Online (AJOL)

Physical-chemical properties of the extrudates including, lateral expansion, bulk density, hardness, water absorption index, water solubility index, as well as proximate composition were determined. The extrudates exhibited 240-300% lateral expansion and 0.067-0.095 g cm-3 bulk density. The water absorption index was ...

Plant-crafted starches for bioplastics production

DEFF Research Database (Denmark)

Sagnelli, Domenico; Hebelstrup, Kim H.; Leroy, Eric

2016-01-01

Transgenically-produced amylose-only (AO) starch was used to manufacture bioplastic prototypes. Extruded starch samples were tested for crystal residues, elasticity, glass transition temperature, mechanical properties, molecular mass and microstructure. The AO starch granule crystallinity was both...... in the storage modulus (E') for AO samples compared to the control. The data support the use of pure starch-based bioplastics devoid of non-polysaccharide fillers....... of the B- and Vh-type, while the isogenic control starch was mainly A-type. The first of three endothermic transitions was attributed to gelatinization at about 60°C. The second and third peaks were identified as melting of the starch and amylose-lipid complexes, respectively. After extrusion, the AO...

Radiation crosslinking of starch/water-soluble polymer blends for hydrogel

International Nuclear Information System (INIS)

Hashim, K.; Mohid, N.; Bahari, K.; Dahlan, K.Z.

2000-01-01

Water-soluble polymers such as PVP(polyvinyl pyrrolidone) and PVA(polyvinyl alcohol), in aqueous solution can form hydrogel easily upon gamma or electron beam irradiation. The properties of hydrogels, particularly for wound dressing application, can be further improved by adding sago starch to the blend. Results show improved gel strength and elongation properties of the hydrogel with increasing sago concentration. It was found that the PVA/sago hydrogel gives better gel strength and elongation than the PVP/sago hydrogel. The tackiness property of the PVA/sago hydrogel increased with increase amount of sago starch added. In case of PVP/sago hydrogel, the tackiness property shows significant increase with increasing amount of sago except for the 5%PVP composition. The swelling properties of PVP/sago and PVA/sago hydrogel decreased with increasing amount of sago but the crosslink density of the hydrogels also reduced. (author)

Radiation crosslinking of starch/water-soluble polymer blends for hydrogel

Energy Technology Data Exchange (ETDEWEB)

Hashim, K.; Mohid, N.; Bahari, K.; Dahlan, K.Z. [Radiation Processing Technology Division, Malaysian Institute Nuclear Technology Research Malaysia (MINT), Bangi, 43000 Kajang (Malaysia)

2000-03-01

Water-soluble polymers such as PVP(polyvinyl pyrrolidone) and PVA(polyvinyl alcohol), in aqueous solution can form hydrogel easily upon gamma or electron beam irradiation. The properties of hydrogels, particularly for wound dressing application, can be further improved by adding sago starch to the blend. Results show improved gel strength and elongation properties of the hydrogel with increasing sago concentration. It was found that the PVA/sago hydrogel gives better gel strength and elongation than the PVP/sago hydrogel. The tackiness property of the PVA/sago hydrogel increased with increase amount of sago starch added. In case of PVP/sago hydrogel, the tackiness property shows significant increase with increasing amount of sago except for the 5%PVP composition. The swelling properties of PVP/sago and PVA/sago hydrogel decreased with increasing amount of sago but the crosslink density of the hydrogels also reduced. (author)

Starch degradation by irradiation

International Nuclear Information System (INIS)

Pruzinec, J.; Hola, O.

1987-01-01

The effect of high energy irradiation on various starch samples was studied. The radiation dose varied between 43 and 200.9 kGy. The viscosity of starch samples were determined by Hoeppler's method. The percentual solubility of the matter in dry starch was evaluated. The viscosity and solubility values are presented. (author) 14 refs

Functional behaviour of polypropylene/ZnO-soluble starch nanocomposites

International Nuclear Information System (INIS)

Chandramouleeswaran, Subramani; Mhaske, S T; Kathe, A A; Varadarajan, P V; Prasad, Virendra; Vigneshwaran, Nadanathangam

2007-01-01

ZnO-polypropylene nanocomposites (nano-PP) were prepared using nanoparticles of ZnO stabilized by soluble starch (nano-ZnO) as filler in PP by the melt mixing process. X-ray diffraction (XRD) and other spectroscopic analysis-ultraviolet-visible (UV-vis), Fourier transform infrared (FTIR) and photoluminescence-revealed the presence and characteristics of nano-ZnO in the composites. The presence of ZnO imparts whiteness, while starch increased the yellowing of polymers. The nanocomposites were analyzed for changes in optical, mechanical, electrical and rheological properties, as influenced by the increasing concentration of nano-ZnO. The mechanical properties were marginally increased and the dielectric strength of the nano-PP increased to a notable level. By monitoring the evolution of the carbonyl absorption bands from FTIR analysis, the efficacy of nano-ZnO in the reduction of photo-degradation due to UV irradiation was demonstrated. The excellent antibacterial activity exhibited by nano-ZnO impregnated PP against two human pathogenic bacteria, Staphylococcus aureus and Klebsiella pneumoniae, makes it a suitable candidate for food packaging applications

Functional behaviour of polypropylene/ZnO soluble starch nanocomposites

Science.gov (United States)

Chandramouleeswaran, Subramani; Mhaske, S. T.; Kathe, A. A.; Varadarajan, P. V.; Prasad, Virendra; Vigneshwaran, Nadanathangam

2007-09-01

ZnO-polypropylene nanocomposites (nano-PP) were prepared using nanoparticles of ZnO stabilized by soluble starch (nano-ZnO) as filler in PP by the melt mixing process. X-ray diffraction (XRD) and other spectroscopic analysis—ultraviolet-visible (UV-vis), Fourier transform infrared (FTIR) and photoluminescence—revealed the presence and characteristics of nano-ZnO in the composites. The presence of ZnO imparts whiteness, while starch increased the yellowing of polymers. The nanocomposites were analyzed for changes in optical, mechanical, electrical and rheological properties, as influenced by the increasing concentration of nano-ZnO. The mechanical properties were marginally increased and the dielectric strength of the nano-PP increased to a notable level. By monitoring the evolution of the carbonyl absorption bands from FTIR analysis, the efficacy of nano-ZnO in the reduction of photo-degradation due to UV irradiation was demonstrated. The excellent antibacterial activity exhibited by nano-ZnO impregnated PP against two human pathogenic bacteria, Staphylococcus aureus and Klebsiella pneumoniae, makes it a suitable candidate for food packaging applications.

Effect of the particle size of maize, rice, and sorghum in extruded diets for dogs on starch gelatinization, digestibility, and the fecal concentration of fermentation products.

Science.gov (United States)

Bazolli, R S; Vasconcellos, R S; de-Oliveira, L D; Sá, F C; Pereira, G T; Carciofi, A C

2015-06-01

The influence of rice, maize, and sorghum raw material particle size in extruded dry dog food on the digestibility of nutrients and energy and the fecal concentration of fermentation products was investigated. Three diets with similar nutrient compositions were formulated, each with 1 starch source. Before incorporation into diets, the cereals were ground into 3 different particle sizes (approximately 300, 450, and 600 µm); therefore, a total of 9 diets were in a 3 × 3 factorial arrangement (3 cereals and 3 particle sizes). Fifty-four beagle dogs (12.0 ± 0.1 kg BW) were randomly assigned to the diets, with 6 dogs per diet. The digestibility was measured with the chromium oxide method. The data were evaluated with ANOVA considering the carbohydrate source, grinding effect, and interactions. The means were compared with the Tukey test and polynomial contrasts (P 0.05); only GE digestibility was reduced at the largest MGD (P production of feces with less lactate (P dogs fed maize and sorghum foods, an increase in propionate and butyrate concentrations were observed as MGD increased (P dogs fed different particle sizes of the cereal starches in the extruded diets, the digestibility and fecal characteristics were affected, and this effect was ingredient dependent.

Influence of nanoparticles on the properties of bionanocomposites from cassava starch

International Nuclear Information System (INIS)

Paglicawan, Marissa A.; Emolaga, Carlo S.; Navarro, Ma. Teresa V.; Celorico, Josefina; Basilia, Blessie A.

2015-01-01

Plastics are widely used packaging materials for food and non-food products due to their desirable material properties and low cost. However, the merits of plastic products have been overshadowed by its non-degradable nature, thereby leading to waste disposal problems. Because of the environmental problem, many researchers are facing to minimize non-degradable to biodegradable materials. Starch is one of the most promising natural polymers because of its inherent biodegradability, overwhelming abundance and its renewability. One of the abundant starch is cassava. The Manihot exculenta Crantz, is known as camoteng-kahoy or balinghoy in the Philippines. The production of thermoplastic starch (also known as plasticized starch or TPS) basically involves three essential components, namely: starch, plasticizer and thermomechanical energy. However, this material has high water solubility and may lose their mechanical properties in humid conditions. One of the possible ways to overcome this problem is through nanocomposite in which consist of a polymer matrix reinforced with nano-dimensional particles. This research involves the processing of cassava starch into thermoplastic starch for packaging application that can be biodegraded in soil or compostable after its usage. Thermoplastic starchs from cassava starch and different nanomaterials were processed by melt-blending method in a twin-screw extruder. The four nanofillers - nanoclay (NC), halloysite nanotube (HNT), nanozeolite (NZ), and nanocalcium carbonate (NCC) were incorporated into the starch matrix in a 3 phr concentration. The resulting biocomposites were characterized in terms of mechanical properties, morphology, thermal properties, moisture absorption, and crystallinity. The newly developed technology based on cassava starch/nano-scale particles nanocomposites upgrade the hdydrophylic and mechanical properties of starch based films. Homogeneously dispersing nanometer size materials, with high length

Modified broken rice starch as fat substitute in sausages

Directory of Open Access Journals (Sweden)

Valéria Maria Limberger

2011-09-01

Full Text Available The demand for low-fat beef products has led the food industry to use fat substitutes such as modified starch. About 14% of broken rice is generated during processing. Nevertheless, this by-product contains high levels of starch; being therefore, great raw material for fat substitution. This study evaluated the applicability of chemically and physically modified broken rice starch as fat substitute in sausages. Extruded and phosphorylated broken rice was used in low-fat sausage formulation. All low-fat sausages presented about 55% reduction in the fat content and around 28% reduction in the total caloric value. Fat replacement with phosphorylated and extruded broken rice starch increased the texture acceptability of low-fat sausages, when compared to low-fat sausages with no modified broken rice. Results suggest that modified broken rice can be used as fat substitute in sausage formulations, yielding lower caloric value products with acceptable sensory characteristics.

Supplementing enzymes to extruded, soybean based diet improves breakdown of non-starch polysaccharides in rainbow trout (Oncorhynchus mykiss)

DEFF Research Database (Denmark)

Dalsgaard, Anne Johanne Tang; Knudsen, Knud Erik Bach; Verlhac, Viviane

2016-01-01

Plant-based feed ingredients typically contain remnants of dietary fibres [DF; non-starch polysaccharides (NSP) and lignin] that have various antinutritive effects in carnivorous fish. Exogenous enzymes have been shown to improve the apparent digestibility coefficients (ADC) of plant-based diets...... presumably by assisting in the breakdown of NSP. This study examined the effects on NSP degradation when supplementing β-glucanase, xylanase, protease or a mix of the three enzymes to an extruded, juvenile rainbow trout (Oncorhynchus mykiss) diet containing 344 g kg−1 de-hulled, solvent-extracted soybean...... meal (SBM). The NSP content in the non-supplemented control diet and in faecal samples from the dietary treatment groups was analysed to determine the recovery/apparent digestibility of cellulose and total non-cellulosic polysaccharide (T-NCP) sugar monomers. The enzymes had significant, positive...

Production and characterization of cornstarch/cellulose acetate/silver sulfadiazine extrudate matrices

Energy Technology Data Exchange (ETDEWEB)

Zepon, Karine Modolon [CIMJECT, Departamento de Engenharia Mecânica, Universidade Federal de Santa Catarina, 88040-900 Florianópolis, SC (Brazil); TECFARMA, Universidade do Sul de Santa Catarina, 88704-900 Tubarão, SC (Brazil); Petronilho, Fabricia [FICEXP, Universidade do Sul de Santa Catarina, 88704-900 Tubarão, SC (Brazil); Soldi, Valdir [POLIMAT, Universidade Federal de Santa Catarina, 88040-900 Florianópolis, SC (Brazil); Salmoria, Gean Vitor [CIMJECT, Departamento de Engenharia Mecânica, Universidade Federal de Santa Catarina, 88040-900 Florianópolis, SC (Brazil); Kanis, Luiz Alberto, E-mail: luiz.kanis@unisul.br [TECFARMA, Universidade do Sul de Santa Catarina, 88704-900 Tubarão, SC (Brazil)

2014-11-01

The production and evaluation of cornstarch/cellulose acetate/silver sulfadiazine extrudate matrices are reported herein. The matrices were melt extruded under nine different conditions, altering the temperature and the screw speed values. The surface morphology of the matrices was examined by scanning electron microscopy. The micrographs revealed the presence of non-melted silver sulfadiazine microparticles in the matrices extruded at lower temperature and screw speed values. The thermal properties were evaluated and the results for both the biopolymer and the drug indicated no thermal degradation during the melt extrusion process. The differential scanning analysis of the extrudate matrices showed a shift to lower temperatures for the silver sulfadiazine melting point compared with the non-extruded drug. The starch/cellulose acetate matrices containing silver sulfadiazine demonstrated significant inhibition of the growth of Pseudomonas aeruginosa and Staphylococcus aureus. In vivo inflammatory response tests showed that the extrudate matrices, with or without silver sulfadiazine, did not trigger chronic inflammatory processes. - Highlights: • Melt extruded bio-based matrices containing silver sulfadiazine was produced. • The silver sulfadiazine is stable during melt-extrusion. • The extrudate matrices shown bacterial growth inhibition. • The matrices obtained have potential to development wound healing membranes.

Hot-melt extrusion of sugar-starch-pellets.

Science.gov (United States)

Yeung, Chi-Wah; Rein, Hubert

2015-09-30

Sugar-starch-pellets (syn. sugar spheres) are usually manufactured through fluidized bed granulation or wet extrusion techniques. This paper introduces hot-melt extrusion (HME) as an alternative method to manufacture sugar-starch-pellets. A twin-screw extruder coupled with a Leistritz Micro Pelletizer (LMP) cutting machine was utilized for the extrusion of different types (normal-, waxy-, and high-amlyose) of corn starch, blended with varying amounts of sucrose. Pellets were characterized for their physicochemical properties including crystallinity, particle size distribution, tensile strength, and swelling expansion. Furthermore, the influence of sugar content and humidity on the product was investigated. Both sucrose and water lowered the Tg of the starch system allowing a convenient extrusion process. Mechanical strength and swelling behavior could be associated with varying amylose and amylopectin. X-ray powder diffractometric (XRPD) peaks of increasing sucrose contents appeared above 30%. This signified the oversaturation of the extruded starch matrix system with sucrose. Otherwise, had the dissolved sucrose been embedded into the molten starch matrix, no crystalline peak could have been recognized. The replacement of starch with sucrose reduced the starch pellets' swelling effect, which resulted in less sectional expansion (SEI) and changed the surface appearance. Further, a nearly equal tensile strength could be detected for sugar spheres with more than 40% sucrose. This observation stands in good relation with the analyzed values of the commercial pellets. Both techniques (fluidized bed and HME) allowed a high yield of spherical pellets (less friability) for further layering processes. Thermal influence on the sugar-starch system is still an obstacle to be controlled. Copyright © 2015 Elsevier B.V. All rights reserved.

Desenvolvimento de snacks extrusados a partir de misturas de farinha de soja, fécula e farelo de mandioca Development of extruded snacks from blends of soya flour, cassava starch and bran

Directory of Open Access Journals (Sweden)

Fernanda Rossi Moretti Trombini

2013-01-01

Full Text Available Neste trabalho, objetivou-se avaliar o efeito das condições de extrusão sobre as propriedades físicas de produtos extrusados. Foi utilizado o delineamento central composto rotacional com quatro variáveis independentes (2(4 e a metodologia de superfície de resposta para avaliar os resultados de índice de expansão, volume específico, índice de absorção de água, índice de solubilidade em água e cor, de acordo com as variações de temperatura de extrusão, rotação da rosca, porcentagem de farelo de mandioca e porcentagem de farinha de soja. Os resultados indicam que é possível produzir novos produtos extrusados com boas propriedades físicas a partir de misturas de farinha de soja, fécula e farelo de mandioca.This study aimed to evaluate the effect of the extrusion conditions on physical properties of extruded products. A factorial central composite design (2(4 with four independent variables and the response surface methodology were used to evaluate the results of expansion index, specific volume, water absorption index, water solubility index and color, according to the variations in barrel temperature, screw speed, percentage of cassava bran and percentage of soya flour. The results indicate that is possible to produce new extruded products with good physical properties from blends of soya flour, cassava starch and bran.

[Effect of extrusion on protein and starch bioavailability in corn and lima bean flour blends].

Science.gov (United States)

Pérez-Navarrete, Cecilia; Betancur-Ancona, David; Casotto, Meris; Carmona, Andrés; Tovar, Juscelino

2007-09-01

Extrusion is used to produce crunchy expanded foods, such as snacks. The nutritional impact of this process has not been studied sufficiently. In this study, in vitro and in vivo protein and starch bioavailability was evaluated in both raw and extruded corn (Zea mays)(C) and lima bean (Phaseolus lunatus)(B) flour blends, prepared in 75C/25B and 50C/ 50B (p/p) proportions. These were processed with a Brabender extruder at 160 degrees C, 100 rpm and 15.5% moisture content. Proximate composition showed that in the extruded products protein and ash contents increased whereas the fat level decreased. In vitro protein digestibility was higher in the extrudates (82%) than in the raw flours (77%). Potentially available starch and resistant starch contents decreased with extrusion. The in vitro assays indicated that extrusion improved protein and starch availability in the studied blends. In vivo bioavailability was evaluated using the rice weevil (Sithophilus oryzae) as a biological model. The most descriptive biomarkers of the changes suggested by the in vivo tests were body protein content (increased by extrusion) and intestinal a-amylase activity (decreased by processing). Overall, results suggest that extrusion notably increases the nutritional quality of corn and lima bean flour blends.

Water Susceptibility and Mechanical Properties of Thermoplastic Starch–Pectin Blends Reactively Extruded with Edible Citric Acid

OpenAIRE

Da Róz,Alessandra Luzia; Veiga-Santos,Pricila; Ferreira,Adriane Medeiros; Antunes,Thaís Cristina Ribeiro; Leite,Fabio de Lima; Yamaji,Fabio Minoru; Carvalho,Antonio José Felix de

2016-01-01

Pectin and starch are edible, non-toxic, biodegradable and obtained from renewable sources. Also, have the benefit to be easily cross-linked producing hydrogels. Reactive extrusion with edible citric acid and cross linking interactions was evaluated on extruded thermoplastic in natura and cationic starch-pectin blends. Materials water susceptibility and mechanical properties were characterised. Reactive extrusion decreased (up to 75% in natura starch) mechanical properties. Also have decrease...

Evidence that cellulolysis by an anaerobic ruminal fungus is catabolite regulated by glucose, cellobiose, and soluble starch

International Nuclear Information System (INIS)

Morrison, M.; Mackie, R.I.; Kistner, A.

1990-01-01

A Piromyces-like ruminal fungus was used to study preferential carbohydrate utilization of [U- 14 C]cellulose, both alone and in combination with several soluble sugars. For cells grown on cellulose alone, cellulolytic activity was immediate and, initially, greater than that observed in the presence of added carbohydrate. Cellulolytic activity remained minimal in cultures containing cellulose plus glucose or cellobiose until the soluble sugar was depleted. Soluble starch also regulated cellulose activity but to a lesser extent. The results presented suggest that some fungal cellulases are susceptible to catabolite regulatory mechanisms

Effect of Some Extrusion Variables on Rheological Properties and Physicochemical Changes of Cornmeal Extruded by Twin Screw Extruder

Directory of Open Access Journals (Sweden)

Chang Y.K.

1998-01-01

Full Text Available The effect of extrusion variables, such as barrel temperature (100 to 170ºC, feed rate (100 to 500 g/min, feed moisture (20 to 40 g/100 g wet basis, screw speed rate (from 100 to 500 rpm, and slit die rheometer configuration (0.15 and 0.30 cm height were studied using a co-rotating intermeshing twin-screw extruder coupled to a slit die rheometer on the rheological properties of yellow cornmeal. An increase in feed rate decreased WAI and WSI, but increased the viscosity values. The temperature interacts strongly with screw speed in affecting the WSI. The most important factor in starch degradation was the screw speed. Increasing the screw speed completely modifies the organised structure of starch (crystalline region.

A starch-binding domain identified in α-amylase (AmyP) represents a new family of carbohydrate-binding modules that contribute to enzymatic hydrolysis of soluble starch.

Science.gov (United States)

Peng, Hui; Zheng, Yunyun; Chen, Maojiao; Wang, Ying; Xiao, Yazhong; Gao, Yi

2014-04-02

A novel starch-binding domain (SBD) that represents a new carbohydrate-binding module family (CBM69) was identified in the α-amylase (AmyP) of the recently established alpha-amylase subfamily GH13_37. The SBD and its homologues come mostly from marine bacteria, and phylogenetic analysis indicates that they are closely related to the CBM20 and CBM48 families. The SBD exhibited a binding preference toward raw rice starch, but the truncated mutant (AmyPΔSBD) still retained similar substrate preference. Kinetic analyses revealed that the SBD plays an important role in soluble starch hydrolysis because different catalytic efficiencies have been observed in AmyP and the AmyPΔSBD. Copyright © 2014 Federation of European Biochemical Societies. Published by Elsevier B.V. All rights reserved.

Material properties and glass transition temperatures of different thermoplastic starches after extrusion processing

NARCIS (Netherlands)

Janssen, Léon P.B.M.; Karman, Andre P.; Graaf, Robbert A. de

Four different starch sources, namely waxy maize, wheat, potato and pea starch were extruded with the plasticizer glycerol, the latter in concentrations of 15, 20 and 25% (w/w). The glass transition temperatures of the resulting thermoplastic products were measured by Dynamic Mechanical Thermal

Plant-crafted starches for bioplastics production.

Science.gov (United States)

Sagnelli, Domenico; Hebelstrup, Kim H; Leroy, Eric; Rolland-Sabaté, Agnès; Guilois, Sophie; Kirkensgaard, Jacob J K; Mortensen, Kell; Lourdin, Denis; Blennow, Andreas

2016-11-05

Transgenically-produced amylose-only (AO) starch was used to manufacture bioplastic prototypes. Extruded starch samples were tested for crystal residues, elasticity, glass transition temperature, mechanical properties, molecular mass and microstructure. The AO starch granule crystallinity was both of the B- and Vh-type, while the isogenic control starch was mainly A-type. The first of three endothermic transitions was attributed to gelatinization at about 60°C. The second and third peaks were identified as melting of the starch and amylose-lipid complexes, respectively. After extrusion, the AO samples displayed Vh- and B-type crystalline structures, the B-type polymorph being the dominant one. The AO prototypes demonstrated a 6-fold higher mechanical stress at break and 2.5-fold higher strain at break compared to control starch. Dynamic mechanical analysis showed a significant increase in the storage modulus (E') for AO samples compared to the control. The data support the use of pure starch-based bioplastics devoid of non-polysaccharide fillers. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development of oxidised and heat-moisture treated potato starch film.

Science.gov (United States)

Zavareze, Elessandra da Rosa; Pinto, Vânia Zanella; Klein, Bruna; El Halal, Shanise Lisie Mello; Elias, Moacir Cardoso; Prentice-Hernández, Carlos; Dias, Alvaro Renato Guerra

2012-05-01

This study investigated the effects of sodium hypochlorite oxidation and a heat-moisture treatment of potato starch on the physicochemical, pasting and textural properties of potato starches in addition to the water vapour permeability (WVP) and mechanical properties of potato starch films produced from these starches. The carbonyl contents, carboxyl contents, swelling power, solubility, pasting properties and gel texture of the native, oxidised and heat-moisture treated (HMT) starches were evaluated. The films made of native, oxidised and HMT starches were characterised by thickness, water solubility, colour, opacity, mechanical properties and WVP. The oxidised and HMT starches had lower viscosity and swelling power compared to the native starch. The films produced from oxidised potato starch had decreased solubility, elongation and WVP values in addition to increased tensile strength compared to the native starch films. The HMT starch increased the tensile strength and WVP of the starch films compared to the native starch. Copyright © 2011 Elsevier Ltd. All rights reserved.

Functional properties of extruded nano composites based on cassava starch, polyvinyl alcohol and montmorillonite; Propriedades funcionais de nanocompositos extrusados de amido de mandioca, alcool polivinilico e montmorilonita

Energy Technology Data Exchange (ETDEWEB)

Debiagi, Flavia; Mali, Suzana [Departamento de Bioquimica e Biotecnologia, Universidade Estadual de Londrina, PR (Brazil)

2011-07-01

The objectives of this work were to produce expanded nano composites (foams) based on starch, PVA and sodium montmorillonite and characterize them according to their expansion index (EI), density, water absorption capacity (WSC), mechanical properties and X-ray diffraction. The nano composites were prepared in a single-screw extruder using different starch contents (97.6 - 55.2 g/100 g formulation), PVA (0 - 40 g/100 g formulation), unmodified nano clay - Closite - Na (0 - 4. 8 g/100 g formulation) and glycerol (20 g/100 g formulation) as plasticizer. The addition of montmorillonite and PVA resulted in an increase of EI and a decrease of density of the samples, and reduced WSC and increased the mechanical strength of the foams. Through the analysis of X-ray diffraction can be observed that the addition of montmorillonite led to production of intercalated nano composites in all samples. (author)

Production and characterization of novel starch and poly(butylene adipate-co-terephthalate)-based materials and their applications

Science.gov (United States)

Stagner, Jacqueline Ann

This work focuses on the production and characterization of blends of maleated thermoplastic starch (MTPS) and poly(butylenes adipate-co-terephthalate) and their application for use as thermoformed objects, films, and foams. First, by the production and characterization of maleated thermoplastic starch (MTPS) synthesized by reactive extrusion in a twin-screw extruder, a better understanding of MTPS was gained. This reactive thermoplastic starch was prepared with glycerol as the plasticizer, maleic anhydride (MA), and free-radical initiator, 2,5-bis(tert-butylperoxy)-2,5-dimethylhexane (Luperox 101). Dynamic light scattering (DLS), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), soxhlet extraction in acetone, and environmental scanning electron microscopy (ESEM) were performed to determine the effect of maleation, extrusion temperature, initiator concentration, and maleic anhydride concentration on the resulting MTPS. Next, maleated thermoplastic starch (MTPS) and thermoplastic starch (TPS) were reactively blended in a twin-screw extruder with a biodegradable polyester, poly(butylene adipate-co-terephthalate) (PBAT). The blends were extruded to produce thermoformable sheets. The mechanical properties of the sheets were characterized by tensile and puncture tests. Proof of grafting was determined by soxhlet extraction in dichloromethane and FTIR analysis. Observations of the thermal properties were made using DSC, while the surface of the sheets was imaged using ESEM. Blends of MTPS and PBAT were also extruded to produce films. Mechanical testing (tensile and puncture tests) and barrier performance testing (carbon dioxide, oxygen, and water vapor permeability) were performed on the films. Transmission electron microscopy (TEM) was used to image the blends and to view the dispersion of the various phases. Finally, blends of MTPS and PBAT were extruded with an endothermic chemical blowing agent to produce foams. The foams were

Starch Digestibility and Functional Properties of Rice Starch Subjected to Gamma Radiation

Directory of Open Access Journals (Sweden)

Luís Fernando Polesi

2018-01-01

Full Text Available This study investigated the effect of gamma radiation on the digestibility and functional properties of rice starch. Rice cultivars IRGA417 and IAC202 were used for isolation of starch by the alkaline method. Starch samples were irradiated with 1, 2 and 5 kGy doses of 60Co at a rate of 0.4 kGy/h. A control sample, which was not irradiated, was used for comparison. Irradiated and control starches were characterized by in vitro starch digestibility, total dietary fiber, color, water absorption index, water solubility index, syneresis, swelling factor, amylose leaching, pasting properties and gel firmness. Irradiations changed starch digestibility differently in either cultivar. Increasing radiation doses promoted increase in the color parameter b* (yellow, elevation in the capacity to absorb water, and solubility in water as well as the amylose leached from granules for both cultivars. Pasting properties showed a decrease that was proportional to the dose applied, caused by the depolymerization of starch molecules. Gel firmness of the starch from IAC202 was inversely proportional to the radiation dose applied, whereas for IRGA417, there was a reduction at 5 kGy dose. Rice starches can be modified by irradiation to exhibit different functional characteristics and they can be used by the food industries in products such as soups, desserts, flans, puddings and others.

Physicochemical properties of black pepper (Piper nigrum) starch.

Science.gov (United States)

Zhu, Fan; Mojel, Reuben; Li, Guantian

2018-02-01

Black pepper (Piper nigrum) is among the most popular spices around the world. Starch is the major component of black pepper. However, little is known about functional properties of this starch. In this study, swelling, solubility, thermal properties, rheology, and enzyme susceptibility of 2 black pepper starches were studied and compared with those of maize starch. Pepper starch had lower water solubility and swelling power than maize starch. It had higher viscosity during pasting event. In dynamic oscillatory analysis, pepper starch had lower storage modulus. Thermal analysis showed that pepper starch had much higher gelatinization temperatures (e.g., conclusion temperature of 94°C) than maize starch. The susceptibility to α-amylolysis of pepper starch was not very different from that of maize starch. Overall, the differences in the physicochemical properties of the 2 pepper starches are non-significant. The relationships between structure (especially amylopectin internal molecular structure) and properties of starch components are highlighted. Copyright © 2017 Elsevier Ltd. All rights reserved.

Moisture sorption characteristics of extrusion-cooked starch protective loose-fill cushioning foams

Science.gov (United States)

Combrzyński, Maciej; Mościcki, Leszek; Kwaśniewska, Anita; Oniszczuk, Tomasz; Wójtowicz, Agnieszka; Sołowiej, Bartosz; Gładyszewska, Bożena; Muszyński, Siemowit

2017-10-01

The aim of this work was to determine the water vapour sorption properties of thermoplastic starch filling foams processed by extrusion-cooking technique from various combinations of potato starch and two foaming agents: poly(vinyl) alcohol and Plastronfoam, in amount of 1, 2 and 3% each. Foams were processed with the single screw extruder-cooker at two different screw rotational speeds 100 and 130 r.p.m. The sorption isotherms of samples were determined and described using the Guggenheim-Anderson-de Boer model. Also, the kinetics of water vapour adsorption by foams, as a function of time, was measured and fitted with Peleg model. On the basis of the analysis the influence of the applied foaming agents, as well as the technological parameters of extrusion-cooking process in relation to water vapour adsorption by thermoplastic starch foams was demonstrated. There was no difference between the shapes of the isotherms for poly(vinyl) alcohol foams while for Plastronfoam foams a notable difference among foams extruded at 100 r.p.m. was observed in the regions of low and high humidity content. The analysis of the Guggenheim-Anderson-de Boer model parameters showed that the water molecules were less strongly bound with the foam surface when extruded at a lower screw speed.

THE DESIGN, FABRICATION AND PRELIMINARY TESTING OF AN INDIGENOUS SINGLE SCREW EXTRUDER

Directory of Open Access Journals (Sweden)

FOLASAYO T. FAYOSE

2017-10-01

Full Text Available Developing countries including Nigeria have become dumping grounds of unserviceable and broken down imported machineries because of poor adaptation. Detailed study and design of machines to suit local conditions will prevent poor adaptation of imported machines and high initial costs. In this study, a single screw starch extruder was designed, fabricated and tested using locally available materials. The extruder is the dry type and it has 27.12 kg/s capacity, a compression ratio of 4.5: 1 and is powered by a 5.5 kW electric motor. It consists of a hopper, feeding screw, extruder screw rotating in a barrel and variable die, all made of stainless steel. A unit of the machine costs N 470, 390.00.00 as at April 2015. When used to process cassava flour, a maximum temperature of 114°C was attained through viscous dissipation, up to an actual screw speed of 98.96 rpm (1.65 Hz and extruder efficiency of 64%. Barrel temperature varied directly with extrusion time in a polynomial trend while actual extruder screw speed and efficiency varied inversely with extrusion time and it is best fitted with a polynomial trend.

Properties of whey protein isolates extruded under acidic and alkaline conditions.

Science.gov (United States)

Onwulata, C I; Isobe, S; Tomasula, P M; Cooke, P H

2006-01-01

Whey proteins have wide acceptance and use in many products due to their beneficial nutritional properties. To further increase the amount of whey protein isolates (WPI) that may be added to products such as extruded snacks and meats, texturization of WPI is necessary. Texturization changes the folding of globular proteins to improve interaction with other ingredients and create new functional ingredients. In this study, WPI pastes (60% solids) were extruded in a twin-screw extruder at 100 degrees C with 4 pH-adjusted water streams: acidic (pH 2.0 +/- 0.2) and alkaline (pH 12.4 +/- 0.4) streams from 2 N HCl and 2 N NaOH, respectively, and acidic (pH 2.5 +/- 0.2) and alkaline (pH 11.5 +/- 0.4) electrolyzed water streams; these were compared with WPI extruded with deionized water. The effects of water acidity on WPI solubility at pH 7, color, microstructure, Rapid Visco Analyzer pasting properties, and physical structure were determined. Alkaline conditions increased insolubility caused yellowing and increased pasting properties significantly. Acidic conditions increased solubility and decreased WPI pasting properties. Subtle structural changes occurred under acidic conditions, but were more pronounced under alkaline conditions. Overall, alkaline conditions increased denaturation in the extruded WPI resulting in stringy texturized WPI products, which could be used in meat applications.

Irradiation of starches for industrial uses: Chemical and physical effects

International Nuclear Information System (INIS)

Gonzalez, Maria E.

1999-01-01

Corn and cassava starches have been irradiated with gamma doses from 10 to 180 kGy and pastes have been prepared by boiling the starches in water. The rheological properties of the pastes have been determined showing that the 10 kGy dose reduces sharply the viscosity of the aqueous pastes. The solubility of the irradiated starches has been also studied. The cassava starch irradiated with 180 kGy is soluble in boiling water and remains soluble at room temperature. After some considerations on the chemical effects of the irradiation it is concluded that the irradiation technique is suitable to replace the chemical treatment in many industrial applications of the starch. (author)

Thermal, Mechanical and Water Resistance Properties of LDPE/Starch Bio-Based Polymer Blends for Food Packing Applications

OpenAIRE

Berber Yamak, Hale

2016-01-01

In this study, low density polyethylene, LDPE was melt blended with starch using twin screw extruder to form biodegradable polymer blends. The LDPE/starch blend films used in food packing were obtained by hot pressing of the granules produced by extrusion process. The starch content was varied from 0 to 40 wt% of LDPE. To provide fine starch dispersion, glycerol and zinc stearate were used as plasticizer and compatibilizer, respectively. The effect of starch content on the properties of LDPE ...

Characterisation of hydroxypropylated crosslinked sago starch as compared to commercial modified starches

Directory of Open Access Journals (Sweden)

Saowakon Wattanachant

2002-07-01

Full Text Available The characteristics of hydroxypropylated crosslinked sago starch (HPST were determined and compared with five types of commercial modified starches (CMST in order to evaluate its quality for further applications. The HPST was prepared on a large scale having molar substitution (MS and degree substitution (DS values in the range of 0.038 to 0.045 and 0.004 to 0.005, respectively. The properties of HPST in terms of sediment volume, swelling power, solubility and paste clarity were 15.75%, 16.7, 8.62% and 5.18%T650 , respectively. The MS value, phosphorus content, paste clarity, swelling power and syneresis after six freeze-thaw cycles of HPST when compared to that of commercially available modified starches which are normally used or incorporated in acidic, frozen and canned foods did not differ significantly. The pasting characteristic of HPST exhibited thin to thick viscosity which was similar (P>0.05 to that of commercial hydroxypropylated crosslinked tapioca starch (NAT 8. The acid stability, solubility and freeze-thaw stability of both starches were also similar (P>0.05 but the swelling power of HPST was slightly lower (P<0.05 than that of NAT 8 .

Towards an optimal process for gelatinisation and hydrolysis of highly concentrated starch-water mixtures with alpha-amylase from B. licheniformis

NARCIS (Netherlands)

Baks, T.; Kappen, F.H.J.; Janssen, A.E.M.; Boom, R.M.

2008-01-01

The enzymatic hydrolysis of starch is usually carried out with 30¿35 w/w% starch in water. Higher substrate concentrations (50¿70 w/w%) were reached by using a twin-screw extruder for gelatinisation and for mixing enzyme with gelatinised starch prior to enzymatic hydrolysis in a batch reactor. The

Synthesis and properties of fatty acid starch esters.

Science.gov (United States)

Winkler, Henning; Vorwerg, Waltraud; Wetzel, Hendrik

2013-10-15

Being completely bio-based, fatty acid starch esters (FASEs) are attractive materials that represent an alternative to crude oil-based plastics. In this study, two synthesis methods were compared in terms of their efficiency, toxicity and, especially, product solubility with starch laurate (C12) as model compound. Laurates (DS>2) were obtained through transesterification of fatty acid vinylesters in DMSO or reaction with fatty acid chlorides in pyridine. The latter lead to higher DS-values in a shorter reaction time. But due to the much better solubility of the products compared to lauroyl chloride esterified ones, vinylester-transesterification was preferred to optimize reaction parameters, where reaction time could be shortened to 2h. FASEs C6-C18 were also successfully prepared via transesterification. To determine the DS of the resulting starch laurates, the efficient ATR-IR method was compared with common methods (elementary analysis, (1)H NMR). Molar masses (Mw) of the highly soluble starch laurates were analyzed using SEC-MALLS (THF). High recovery rates (>80%) attest to the outstanding solubility of products obtained through transesterification, caused by a slight disintegration during synthesis. Particle size distributions (DLS) demonstrated stable dissolutions in CHCl3 of vinyl laurate esterified - contrary to lauroyl chloride esterified starch. For all highly soluble FASEs (C6-C18), formation of concentrated solutions (10 wt%) is feasible. Copyright © 2013 Elsevier Ltd. All rights reserved.

Extrusion and Extruded Products: Changes in Quality Attributes as Affected by Extrusion Process Parameters: A Review.

Science.gov (United States)

Alam, M S; Kaur, Jasmeen; Khaira, Harjot; Gupta, Kalika

2016-01-01

Extrusion of foods is an emerging technology for the food industries to process and market a large number of products of varying size, shape, texture, and taste. Extrusion cooking technology has led to production of wide variety of products like pasta, breakfast cereals, bread crumbs, biscuits, crackers, croutons, baby foods, snack foods, confectionery items, chewing gum, texturized vegetable protein (TVP), modified starch, pet foods, dried soups, dry beverage mixes etc. The functional properties of extruded foods plays an important role for their acceptability which include water absorption, water solubility, oil absorption indexes, expansion index, bulk density and viscosity of the dough. The aim of this review is to give the detailed outlines about the potential of extrusion technology in development of different types of products and the role of extrusion-operating conditions and their effect on product development resulting in quality changes i.e physical, chemical, and nutritional, experienced during the extrusion process.

Changes in physical properties of extruded sour cassava starch and quinoa flour blend snacks Mudanças nas propriedades físicas de snacks extrusados de misturas de polvilho azedo e farinha de quinoa

Directory of Open Access Journals (Sweden)

Lívia Giolo Taverna

2012-12-01

Full Text Available Given the broad acceptance of sour cassava starch biscuits in Brazil and the nutritional quality of quinoa flour, this study aimed to evaluate the effect of extrusion temperature, screw speed, moisture, and amount of quinoa flour on the physical properties of puffed snacks. Extrusion process was carried out using a single-screw extruder in a factorial central composite design with four factors. Effects of moisture and amount of quinoa flour on the expansion index and specific volume of snacks were observed. There was a pronounced increase in water solubility index of blends with the extrusion process with significant effects of all process parameters on the WSI. Higher water absorption index (WAI was observed under high temperature, low moisture, and lower quinoa flour amount. Temperature and amount of quinoa flour influenced the color of the snacks. A positive quadratic effect of quinoa flour on hardness of products was observed. Blends of sour cassava starch and quinoa flour have good potential for use as raw material in production of extruded snacks with good physical properties.Dada a ampla aceitação do biscoito de polvilho azedo no Brasil e a qualidade nutricional da farinha de quinoa, este trabalho objetivou avaliar o efeito da temperatura de extrusão, rotação da rosca, umidade e porcentagem de farinha de quinoa sobre as propriedades físicas de snacks expandidos. O processo foi realizado em extrusor monorrosca, seguindo o delineamento central composto rotacional para quatro fatores. Foi observado o efeito da umidade e da porcentagem de farinha de quinoa sobre o índice de expansão e volume específico. Houve um aumento pronunciado na solubilidade das misturas com o processo de extrusão, com efeitos significativos de todos os parâmetros de processo no ISA. Maior índice de absorção de água (IAA foi observado em alta temperatura, baixa umidade e menor porcentagem de farinha de quinoa. Temperatura e porcentagem de farinha de

Impact of polymer type on bioperformance and physical stability of hot melt extruded formulations of a poorly water soluble drug.

Science.gov (United States)

Mitra, Amitava; Li, Li; Marsac, Patrick; Marks, Brian; Liu, Zhen; Brown, Chad

2016-05-30

Amorphous solid dispersion formulations have been widely used to enhance bioavailability of poorly soluble drugs. In these formulations, polymer is included to physically stabilize the amorphous drug by dispersing it in the polymeric carrier and thus forming a solid solution. The polymer can also maintain supersaturation and promote speciation during dissolution, thus enabling better absorption as compared to crystalline drug substance. In this paper, we report the use of hot melt extrusion (HME) to develop amorphous formulations of a poorly soluble compound (FaSSIF solubility=1μg/mL). The poor solubility of the compound and high dose (300mg) necessitated the use of amorphous formulation to achieve adequate bioperformance. The effect of using three different polymers (HPMCAS-HF, HPMCAS-LF and copovidone), on the dissolution, physical stability, and bioperformance of the formulations was demonstrated. In this particular case, HPMCAS-HF containing HME provided the highest bioavailability and also had better physical stability as compared to extrudates using HPMCAS-LF and copovidone. The data demonstrated that the polymer type can have significant impact on the formulation bioperformance and physical stability. Thus a thorough understanding of the polymer choice is imperative when designing an amorphous solid dispersion formulation, such that the formulation provides robust bioperformance and has adequate shelf life. Copyright © 2016 Elsevier B.V. All rights reserved.

Numerical Analysis of the Reaction-diffusion Equation for Soluble Starch and Dextrin as Substrates of Immobilized Amyloglucosidase in a Porous Support by Using Least Square Method

Directory of Open Access Journals (Sweden)

Ali Izadi

2015-10-01

Full Text Available In this study, substrates concentration profile has been studied in a porous matrix containing immobilized amyloglucosidase for glucose production. This analysis has been performed by using of an analytical method called Least Square Method and results have been compared with numerical solution. Effects of effective diffusivity (, Michael's constant (, maximum reaction rate ( and initial substrate concentration ( are studied on Soluble Starch and Dextrin concentration in the spherical support. Outcomes reveal that Least Square Method has an excellent agreement with numerical solution and in the center of support, substrate concentration is minimum and increasing of effective diffusivity and Michael's constant reduce the Soluble Starch and Dextrin profile gradient.

Utilization of smoked salmon trim in extruded smoked salmon jerky.

Science.gov (United States)

Kong, J; Dougherty, M P; Perkins, L B; Camire, M E

2012-06-01

During smoked salmon processing, the dark meat along the lateral line is removed before packaging; this by-product currently has little economic value. In this study, the dark meat trim was incorporated into an extruded jerky. Three formulations were processed: 100% smoked trim, 75% : 25% smoked trim : fresh salmon fillet, and 50% : 50% smoked trim : fresh salmon blends (w/w basis). The base formulation contained salmon (approximately 83.5%), tapioca starch (8%), pregelatinized potato starch (3%), sucrose (4%), salt (1.5%), sodium nitrate (0.02%), and ascorbyl palmitate (0.02% of the lipid content). Blends were extruded in a laboratory-scale twin-screw extruder and then hot-smoked for 5 h. There were no significant differences among formulations in moisture, water activity, and pH. Protein was highest in the 50 : 50 blend jerky. Ash content was highest in the jerky made with 100% trim. Total lipids and salt were higher in the 100% trim jerky than in the 50 : 50 blend. Hot smoking did not adversely affect docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA) content in lipids from 100% smoked trim jerky. Servings of salmon jerky made with 75% and 100% smoked trim provided at least 500 mg of EPA and DHA. The 50 : 50 formulation had the highest Intl. Commission on Illumination (CIE) L*, a*, and b* color values. Seventy consumers rated all sensory attributes as between "like slightly" and "like moderately." With some formulation and processing refinements, lateral line trim from smoked salmon processors has potential to be incorporated into acceptable, healthful snack products. Dark meat along the lateral line is typically discarded by smoked salmon processors. This omega-3 fatty acid rich by-product can be used to make a smoked salmon jerky that provides a convenient source of these healthful lipids for consumers. © 2012 Institute of Food Technologists®

Prediction of Starch, Soluble Sugars and Amino Acids in Potatoes (Solanum tuberosum L.) Using Hyperspectral Imaging, Dielectric and LF-NMR Methodologies

DEFF Research Database (Denmark)

Kjær, Anders; Nielsen, Glenn; Stærke, Søren

2016-01-01

Handling and processing of potatoes is performed in increasingly large and more automated facilities, and the industry calls for more automated machinery for quality assessment and sorting by concentration of starch, soluble sugars, protein, amino acids etc. of the potato tubers. The present study...... cultivars were simultaneously sampled for analyses of content and scanned by the five different scanning methods. The resulting multivariate dataset was used to estimate the prediction ability of the individual scanning methods on starch-related parameters, selected simple sugars, selected amino acids......, conductivity of pressed cell sap and cell sizes. Results showed that most types of spectral analyses had relatively high potential for predicting the starch-related parameters and medium potential for predicting the concentration of the reducing sugars fructose and glucose. Most methods showed medium potential...

Obtaining and characterization of a biodegradable polymer starting from the tapioca starch

International Nuclear Information System (INIS)

Ruiz Aviles, Gladys

2006-01-01

This study focuses on the preparation of tapioca starch biodegradable polymer, processed by blends of starch modified with glycerin and water as plasticizers, by using roll mill and a single-screw extruder in the process. During extrusion, there is a series of variables to control namely: the barrel temperature profile, screw torque and screw rotation speed. Tensile test, differential scanning calorimetric (DSC), thermogravimetric analysis (TGA), Fourier transformer infrared spectroscopy (FTIR) and morphology were used in the process

Effects of extrusion variables on the properties of waxy hulless barley extrudates.

Science.gov (United States)

Köksel, Hamit; Ryu, Gy-Hyung; Başman, Arzu; Demiralp, Hande; Ng, Perry K W

2004-02-01

The objective of this research was to investigate the extrudability of waxy hulless barley flour under various extrusion conditions. Waxy hulless barley flour was processed in a laboratory-scale corotating twin-screw extruder with different levels of feed moisture content (22.3, 26.8, and 30.7%) and die temperature (130, 150, and 170 degrees C) to develop a snack food with high beta-glucan content. The effects of extrusion condition variables (screw configuration, moisture, and temperature) on the system variables (pressure and specific mechanical energy), the extrudate physical properties (sectional expansion index, bulk density), starch gelatinization, pasting properties (cold peak viscosity, trough viscosity, and final viscosity), and beta-glucan contents were determined. Results were evaluated by using response surface methodology. Increased extrusion temperature and feed moisture content resulted in decreases in exit die pressure and specific mechanical energy values. For extrudates extruded under low shear screw configuration (LS), increased barrel temperature decreased sectional expansion index (SEI) values at both low and high moisture contents. The feed moisture seems to have an inverse relationship with SEI over the range studied. Bulk density was higher at higher moisture contents, for both low and high barrel temperatures, for samples extruded under high shear screw configuration (HS) and LS. Cold peak viscosities (CV) were observed in all samples. The CV increased with the increase in extrusion temperature and feed moisture content. Although beta-glucan contents of the LS extrudates were comparable to that of barley flour sample, HS samples had generally lower beta-glucan contents. The extrusion cooking technique seems to be promising for the production of snack foods with high beta-glucan content, especially using LS conditions.

Compositional profile and variation of Distillers Dried Grains with Solubles from various origins with focus on non-starch polysaccharides

DEFF Research Database (Denmark)

Pedersen, Mads Brøgger; Dalsgaard, S.; Knudsen, Knud Erik Bach

2014-01-01

nutrients (e.g. protein, fat, fibre and minerals) after fermentation of starch to ethanol. Corn DDGS differentiated from wheat DDGS by a greater content of fat (P≤0.006), insoluble-NSP (Pcellulose (P=0.032), and arabinose/xylose (P....001). Wheat DDGS differentiated from corn DDGS by a greater content of ash (P=0.001), soluble-NSP (Plignin (P...Corn-, wheat- and mixed cereal Distillers' Dried Grains with Solubles (DDGS) were investigated for compositional variability among DDGS origins, ethanol plants, and the relationship between corn and corresponding DDGS. A total of 138 DDGS samples were analyzed by use of Near Infrared Reflectance...

A new method for the continuous production of single dosed controlled release matrix systems based on hot-melt extruded starch: analysis of relevant process parameters and implementation of an in-process control.

Science.gov (United States)

Kipping, Thomas; Rein, Hubert

2013-05-01

In the present study, we evaluated a novel processing technique for the continuous production of hot-melt extruded controlled release matrix systems. A cutting technique derived from plastics industry, where it is widely used for cutting of cables and wires was adapted into the production line. Extruded strands were shaped by a rotary fly cutter. Special focus is laid on the development of a process analytical technology by evaluating signals obtained from the servo control of the rotary fly cutter. The intention is to provide a better insight into the production process and to offer the ability to detect small variations in process-variables. A co-rotating twin-screw extruder ZSE 27 HP-PH from Leistritz (Nürnberg, Germany) was used to plasticize the starch; critical extrusion parameters were recorded. Still elastic strands were shaped by a rotary fly-cutter type Dynamat 20 from Metzner (Neu-Ulm, Germany). Properties of the final products were analyzed via digital image analysis to point out critical parameters influencing the quality. Important aspects were uniformity of diameter, height, roundness, weight, and variations in the cutting angle. Stability of the products was measured by friability tests and by determining the crushing strength of the final products. Drug loading studies up to 70% were performed to evaluate the capacity of the matrix and to prove the technological feasibility. Changes in viscosities during API addition were analyzed by a Haake Minilab capillary rheometer. X-ray studies were performed to investigate molecular structures of the matrices. External shapes of the products were highly affected by die-swelling of the melt. Reliable reproducibility concerning uniformity of mass could be achieved even for high production rates (>2500cuts/min). Both mechanical strength and die-swelling of the products could be linked to the ratio of amylose to amylopectin. Formulations containing up to 70% of API could still be processed. Viscosity

Physical and mechanical properties of LDPE incorporated with different starch sources

Science.gov (United States)

Kormin, Shaharuddin; Kormin, Faridah; Dalour Hossen Beg, Mohammad; Bijarimi Mat Piah, Mohd

2017-08-01

In this study it was investigated the incorporation of different starches, such as sago starch, corn starch, potato starch, tapioca starch and wheat starch, in low-density polyethylene matrix (LDPE) to enhanced mechanical properties and to obtain partially biodegradable product with the aim to reduce the plastics wastes in the environment. For comparison, virgin LDPE, LDPE with different sources of starch blends were prepared and characterized under the same conditions. The starches were mixed to the LDPE using a twin screw extruder to guarantee the homogeneity of the formulations. The compound were shaping processed by injection moulding. The characterization of those compounds was done by physical (density, MFI), mechanical (Universal tensile machine). The addition of starch to LDPE reduced the MFI values, the tensile strength, elongation at break and impact strength, whereas the elastic modulus, flexural modulus and flexural strength increased. LDPE/SS show the good mechanical behavior compared to other formulation. The physical and mechanical properties were evident when 5 and 30 wt% were added. Water uptake increased with increased starch content and immersion time. The time taken for the composites to equilibrate was about one month even when they were immersed completely in water.

Effects of selected process parameters in extrusion of yam flour (Dioscorea rotundata) on physicochemical properties of the extrudates.

Science.gov (United States)

Sebio, L; Chang, Y K

2000-04-01

Raw yam (Dioscorea rotundata) flour was cooked and extruded in a Brabender single-screw laboratory scale extruder. Response surface methodology using an incomplete factorial design was applied with various combinations of barrel temperature [100, 125, 150 degrees C], feed moisture content [18, 22, 26%] and screw speed [100, 150, 200 rpm]. Initial viscosity at 30 degrees C, water solubility index, expansion and hardness were determined. The highest values of initial viscosity were at the highest barrel temperatures and the highest moisture contents. At high feed moisture content and high barrel temperatures the yam extrudate flour showed the greatest values of water solubility index. The physical properties of the extruded product showed that at high temperature the lower the moisture content the greater the expansion index. Hardness was influenced directly by moisture content and inversely by extrusion temperature. The extrusion of yam flour led to the production of snacks and pre-gelatinized flours of diverse properties. Also extruded yam flour can be successfully used in the preparation of 'futu' (pre-cooked compact dough), a yam-based food, popular in Western Africa.

Effects of processing on physical properties of extruded snacks with blends of sour cassava starch and flaxseed flour

Directory of Open Access Journals (Sweden)

Camila De Barros Mesquita

2013-09-01

Full Text Available The opportunity to supplement common cassava biscuits with a product of higher nutritional value meets consumer expectations. In this work it was studied the effects of process parameters and flaxseed addition on physical properties of expanded snacks. Extrusion process was carried out using a single screw extruder in a factorial central composite rotatable design with four factors: flaxseed flour percentage (0-20%, moisture (12-20%, extrusion temperature (90-130 °C and screw speed (190-270. The effect of extrusion variables was investigated in terms of expansion index, specific volume, water absorption index, water solubility index, color parameters (L*, a* ,b* and hardness. The data analysis showed that variable parameters of the extrusion process and flaxseed flour affected physical properties of puffed snacks. Among the experimental conditions used in the present study, expanded snack products with good physical properties can be obtained under the conditions of 10% flaxseed flour, 230 rpm screw speed, temperature of 90 °C and moisture of 12%.

Physical and functional characteristics of extrudates prepared from fenugreek and oats

Directory of Open Access Journals (Sweden)

Sajad Ahmad Wani

2016-12-01

Full Text Available This study was conducted to investigate the effect of fenugreek seed powder (FSP and oat flour (OF on the physical and functional properties of extruded snack product such as bulk density (BD, hardness (HD, lateral expansion (LE, water absorption index (WAI and water solubility index (WSI using response surface methodology. All the properties were found to be significantly (p < 0.05 affected by proportion of FSP and OF. Results indicated that with the increase in the FSP content, an increase in the values of BD, HD, WAI and WSI was noticed, whereas negative effect of FSP on LE was observed. Results showed negative effect of OF on HD and WSI and an increased effect on BD, LE and WAI of the extruded product. Numerical optimization results showed that a mixture of 2% FSP and 6% OF had higher preference levels for parameters of physical and functional characteristics and could be extruded to produce acceptable quality extrudates.

Effect of composition and processing conditions on selected characteristics of extruded corn instant gruels enriched with fruits addition

Directory of Open Access Journals (Sweden)

Kręcisz Magdalena

2018-01-01

Full Text Available Cranberries and goji berries were used as natural supplements in extruded instant corn gruels. The effects of additive type and level, as well as extrusion-cooking screw speed on selected properties of extrudates were tested. Corn grit was used as the base raw materials and dry and ground goji berries and cranberries were added at 1, 2, 3, 4 and 5%. Extrusion-cooking of blends was performed with a single screw extruder at temperature ranged 125-135°C using various screw speed during processing. Extrudates were ground below 1 mm for instant gruels. Water absorption, water solubility, as well as colour profile were tested. The results showed that the highest water absorption was evaluated for instant gruels consist the highest amount of goji berries extruded at the highest screw speed during processing, while cranberries addition have no significant effect on water absorption. Increasing amount of dry cranberries and goji berries in the recipe affected on lowering the water solubility of the extrudates. Significant effect of fruits on color coordinates was observed. Increasing amount of dry berries lowered lightness L* and yellowness of instant gruels, especially when goji berries were used in the recipe. Increasing the screw speed during processing decreased intensity b* values.

Biodegradable Starch/Copolyesters Film Reinforced with Silica Nanoparticles: Preparation and Characterization

Science.gov (United States)

Lima, Roberta A.; Oliveira, Rene R.; Wataya, Célio H.; Moura, Esperidiana A. B.

Biodegradable starch/copolyesters/silica nanocomposite films were prepared by melt extrusion, using a twin screw extruder machine and blown extrusion process. The influence of the silica nanoparticle addition on mechanical and thermal properties of nanocomposite films was investigated by tensile tests; X-rays diffraction (XRD), differential scanning calorimetry (DSC) and Scanning electron microscopy (SEM) analysis and the correlation between properties was discussed. The results showed that incorporation of 2 % (wt %) of SiO2 nanoparticle in the blend matrix of PBAT/Starch, resulted in a gain of mechanical properties of blend.

Effect of PVA and PDE on selected structural characteristics of extrusion-cooked starch foams

Directory of Open Access Journals (Sweden)

Maciej Combrzyński

2018-03-01

Full Text Available Abstract The aim of this work was to determine selected physical properties of biodegradable thermoplastic starch (TPS filling foams manufactured by extrusion-cooking technique from different combinations of potato starch and two additives: poly(vinyl alcohol PVA and Plastronfoam PDE. Foams were processed with seven starch/additives combinations at two different extruder-cooker’s screw rotational speeds. The densities of starch foams depended significantly on the additive type and content. The linear relationship between the Young modulus and the ultimate compression force and apparent density was found. The foams processed with the addition of PVA had low density, porosity and lower values of the Young modulus than the foams prepared with PDE.

Functional properties of extruded nano composites based on cassava starch, polyvinyl alcohol and montmorillonite

International Nuclear Information System (INIS)

Debiagi, Flavia; Matsuda, Daniel K.M.; Marengo, Vitor A.; Vercelheze, Ana Elisa S.; Mali, Suzana

2011-01-01

The objectives of this work were to produce biodegradable trays based on cassava starch (native or modified by acid), sugarcane fibers and nano clay (sodium montmorillonite) and also to characterize the produced trays according to their density, tensile strength, X-ray diffraction and biodegradability. The trays were obtained by thermoforming into a hydraulic press coupled to a Teflon mold (18 x 23 cm) at 130 degree C/ 20 min and 100 bars of pressure. The peak related to the nano clay (2 = 7.1 o ) were not observed in XRD patterns of the trays, suggesting the formation of an exfoliated structure in the nano composite. The addition of modified starch increased tensile strength and density of the samples, and the addition of fibers and nano clays decreased the tensile strength of native and modified starch trays. The weight loss of trays was not affected by the starch type, however the addition of fibers increased the biodegradation and the addition of nano clays decreased. (author)

Physic-chemical Study of Starch Extracted from Irradiated Corn Flour

International Nuclear Information System (INIS)

Pozo Sanchez, R. del; Alvarez Gil, M.

1986-01-01

The effects of gamma irradiation on starch extracted from irradiated samples of corn flour were studied in the range 0,6 kGy-1,0 kGy. Amylographic properties, solubility and swelling powder of starch samples were determined immediately after irradiation and at 75 days storage at environment conditions (16 0 C-31 0 C, 55%-97% H.R.). Diffraction patterns of crystalline starch were also obtained by X-rays. Gelatinization temperature, swelling powder and diffraction patterns did not change upon irradiation, but a decrease in viscosity and an increase in starch solubility were observed within the dose-range and storage time studied. (author)

Black leaf streak disease affects starch metabolism in banana fruit.

Science.gov (United States)

Saraiva, Lorenzo de Amorim; Castelan, Florence Polegato; Shitakubo, Renata; Hassimotto, Neuza Mariko Aymoto; Purgatto, Eduardo; Chillet, Marc; Cordenunsi, Beatriz Rosana

2013-06-12

Black leaf streak disease (BLSD), also known as black sigatoka, represents the main foliar disease in Brazilian banana plantations. In addition to photosynthetic leaf area losses and yield losses, this disease causes an alteration in the pre- and postharvest behavior of the fruit. The aim of this work was to investigate the starch metabolism of fruits during fruit ripening from plants infected with BLSD by evaluating carbohydrate content (i.e., starch, soluble sugars, oligosaccharides, amylose), phenolic compound content, phytohormones, enzymatic activities (i.e., starch phosphorylases, α- and β-amylase), and starch granules. The results indicated that the starch metabolism in banana fruit ripening is affected by BLSD infection. Fruit from infested plots contained unusual amounts of soluble sugars in the green stage and smaller starch granules and showed a different pattern of superficial degradation. Enzymatic activities linked to starch degradation were also altered by the disease. Moreover, the levels of indole-acetic acid and phenolic compounds indicated an advanced fruit physiological age for fruits from infested plots.

Examination of injection moulded thermoplastic maize starch

Directory of Open Access Journals (Sweden)

2007-12-01

Full Text Available This paper focuses on the effect of the different injection moulding parameters and storing methods on injection moulded thermoplastic maize starch (TPS. The glycerol and water plasticized starch was processed in a twin screw extruder and then with an injection moulding machine to produce TPS dumbbell specimens. Different injection moulding set-ups and storing conditions were used to analyse the effects on the properties of thermoplastic starch. Investigated parameters were injection moulding pressure, holding pressure, and for the storage: storage at 50% relative humidity, and under ambient conditions. After processing the mechanical and shrinkage properties of the manufactured TPS were determined as a function of the ageing time. While conditioning, the characteristics of the TPS changed from a soft material to a rigid material. Although this main behaviour remained, the different injection moulding parameters changed the characteristics of TPS. Scanning electron microscope observations revealed the changes in the material on ageing.

Effects of whey protein concentrate, feed moisture and temperature on the physicochemical characteristics of a rice-based extruded flour.

Science.gov (United States)

Teba, Carla da Silva; Silva, Erika Madeira Moreira da; Chávez, Davy William Hidalgo; Carvalho, Carlos Wanderlei Piler de; Ascheri, José Luis Ramírez

2017-08-01

The influence of whey protein concentrate (WPC), feed moisture and temperature on the physicochemical properties of rice-based extrudates has been investigated. WPC (0.64-7.36g/100g rice) was extruded under 5 moisture (16.64-23.36g/100g) and 5 temperature (106.36-173.64°C) established by a 3 2 central composite rotational design. Physicochemical properties [color, porosimetry, crystallinity, water solubility and absorption, pasting properties, reconstitution test, proximate composition, amino acids, minerals and electrophoresis] were determined. WPC and feed moisture increased redness, yellowness and decreased luminosity. Feed moisture and temperature increased density and total volume pore. WPC and moisture increased crystallinity, but only WPC increased solubility and decrease the retrogradation tendency. Increasing temperature increased the viscosity of the extrudates. The addition of WPC improved the nutritional composition of the extrudates, especially proteins. It is suggested that the extrusion process positively affected the retention of most of the polypeptides chains. Copyright © 2017 Elsevier Ltd. All rights reserved.

Potential of sago starch/carrageenan mixture as gelatin alternative for hard capsule material

Science.gov (United States)

Poeloengasih, Crescentiana Dewi; Pranoto, Yudi; Anggraheni, Frida Dwi; Marseno, Djagal Wiseso

2017-03-01

In order to replace gelatin in capsule shell production, blends of sago starch and carrageenan were developed. Films and capsules were prepared with 10% (w/v) of sago starch, 25% (w/w starch) of glycerol and various carrageenan concentration (1, 2, 3% w/w starch) in two different kappa/iota-carrageenan ratio (1:3 and 3:1). The resulted films and capsules were characterized by mechanical property, water vapor and oxygen permeability. In addition, moisture absorption and solubility of capsule in acid solution were investigated. The results reveal that addition of carrageenan makes the films stronger and less permeable. Higher kappa-carrageenan content improved tensile strength and barrier properties of the films, whereas higher iota-carrageenan content produced films with higher elongation, moisture absorption and capsule solubility in acid solution. Capsule with 2% (w/w starch) of carrageenan at kappa-/iota-ratio 3:1 had the lowest moisture absorption, whereas capsule with 3% (w/w starch) of carrageenan at kappa/iota ratio 1:3 had the highest solubility. It is illustrated that sago starch/carrageenan blends can be used as hard capsule material.

Poly(Lactic Acid) Filled with Cassava Starch-g-Soybean Oil Maleate

Science.gov (United States)

Kiangkitiwan, Nopparut; Srikulkit, Kawee

2013-01-01

Poly(lactic acid), PLA, is a biodegradable polymer, but its applications are limited by its high cost and relatively poorer properties when compared to petroleum-based plastics. The addition of starch powder into PLA is one of the most promising efforts because starch is an abundant and cheap biopolymer. However, the challenge is the major problem associated with poor interfacial adhesion between the hydrophilic starch granules and the hydrophobic PLA, leading to poorer mechanical properties. In this paper, soybean oil maleate (SOMA) was synthesized by grafting soybean oil with various weight percents of maleic anhydride (MA) using dicumyl peroxide (DCP) as an initiator. Then, SOMA was employed for the surface modifying of cassava starch powder, resulting in SOMA-g-STARCH. The obtained SOMA-g-STARCH was mixed with PLA in various weight ratios using twin-screw extruder, resulting in PLA/SOMA-g-STARCH. Finally, the obtained PLA/SOMA-g-STARCH composites were prepared by a compression molding machines. The compatibility, thermal properties, morphology properties, and mechanical properties were characterized and evaluated. The results showed that the compatibility, surface appearance, and mechanical properties at 90 : 10 and 80 : 20 ratios of PLA/SOMA-g-STARCH were the best. PMID:24307883

Effect of pH on Physicochemical Properties of Cassava Starch Modification Using Ozone

Directory of Open Access Journals (Sweden)

Pudjihastuti Isti

2018-01-01

Full Text Available Nowadays, starch modification is carried out in order to change the native properties into the better ones, such as high stability, brightness, and better texture. The objectives of this study are to investigate the effect of pH on carboxyl content, swelling power, and water solubility of starch. This research was divided into two main stages, i.e. starch modification by ozone oxidation and analysis. The physicochemical properties of modified cassava starch were investigated under various reaction pH of 7-10 and the reaction time between 0-240 minutes. Reaction condition at pH 10 provided the higher value of carboxyl content and water solubility, but the lower of swelling power. This increase in solubility indicates that the modified oxidation starch readily dissolves in water, due to its small size granules and high amylose content. The significant changes of both parameters were achieved in the first 120 minutes of ozone reaction times. The graphic pattern of water solubility was in contrast with swelling power.

Design starch: stochastic modeling of starch granule biogenesis.

Science.gov (United States)

Raguin, Adélaïde; Ebenhöh, Oliver

2017-08-15

Starch is the most widespread and abundant storage carbohydrate in plants and the main source of carbohydrate in the human diet. Owing to its remarkable properties and commercial applications, starch is still of growing interest. Its unique granular structure made of intercalated layers of amylopectin and amylose has been unraveled thanks to recent progress in microscopic imaging, but the origin of such periodicity is still under debate. Both amylose and amylopectin are made of linear chains of α-1,4-bound glucose residues, with branch points formed by α-1,6 linkages. The net difference in the distribution of chain lengths and the branching pattern of amylose (mainly linear), compared with amylopectin (racemose structure), leads to different physico-chemical properties. Amylose is an amorphous and soluble polysaccharide, whereas amylopectin is insoluble and exhibits a highly organized structure of densely packed double helices formed between neighboring linear chains. Contrarily to starch degradation that has been investigated since the early 20th century, starch production is still poorly understood. Most enzymes involved in starch growth (elongation, branching, debranching, and partial hydrolysis) are now identified. However, their specific action, their interplay (cooperative or competitive), and their kinetic properties are still largely unknown. After reviewing recent results on starch structure and starch growth and degradation enzymatic activity, we discuss recent results and current challenges for growing polysaccharides on granular surface. Finally, we highlight the importance of novel stochastic models to support the analysis of recent and complex experimental results, and to address how macroscopic properties emerge from enzymatic activity and structural rearrangements. © 2017 The Author(s).

Design starch: stochastic modeling of starch granule biogenesis

Science.gov (United States)

Ebenhöh, Oliver

2017-01-01

Starch is the most widespread and abundant storage carbohydrate in plants and the main source of carbohydrate in the human diet. Owing to its remarkable properties and commercial applications, starch is still of growing interest. Its unique granular structure made of intercalated layers of amylopectin and amylose has been unraveled thanks to recent progress in microscopic imaging, but the origin of such periodicity is still under debate. Both amylose and amylopectin are made of linear chains of α-1,4-bound glucose residues, with branch points formed by α-1,6 linkages. The net difference in the distribution of chain lengths and the branching pattern of amylose (mainly linear), compared with amylopectin (racemose structure), leads to different physico-chemical properties. Amylose is an amorphous and soluble polysaccharide, whereas amylopectin is insoluble and exhibits a highly organized structure of densely packed double helices formed between neighboring linear chains. Contrarily to starch degradation that has been investigated since the early 20th century, starch production is still poorly understood. Most enzymes involved in starch growth (elongation, branching, debranching, and partial hydrolysis) are now identified. However, their specific action, their interplay (cooperative or competitive), and their kinetic properties are still largely unknown. After reviewing recent results on starch structure and starch growth and degradation enzymatic activity, we discuss recent results and current challenges for growing polysaccharides on granular surface. Finally, we highlight the importance of novel stochastic models to support the analysis of recent and complex experimental results, and to address how macroscopic properties emerge from enzymatic activity and structural rearrangements. PMID:28673938

Isosorbide, a green plasticizer for thermoplastic starch that does not retrogradate.

Science.gov (United States)

Battegazzore, Daniele; Bocchini, Sergio; Nicola, Gabriele; Martini, Eligio; Frache, Alberto

2015-03-30

Isosorbide is a non-toxic biodegradable diol derived from bio-based feedstock. It can be used for preparing thermoplastic starch through a semi-industrial process of extrusion. Isosorbide allows some technological advantages with respect to classical plasticizers: namely, direct mixing with starch, energy savings for the low processing temperature required and lower water uptake. Indeed, maize starch was directly mixed with the solid plasticizer and direct fed in the main hopper of a co-rotating twin screw extruder. Starch plasticization was assessed by X-ray diffraction (XRD) and dynamic-mechanical analysis (DMTA). Oxygen permeability, water uptake and mechanical properties were measured at different relative humidity (R.H.) values. These three properties turned out to be highly depending on the R.H. No retrogradation and changing of the material properties were occurred from XRD and DMTA after 9 months. Copyright © 2014 Elsevier Ltd. All rights reserved.

Acetylation and characterization of banana (Musa paradisiaca) starch.

Science.gov (United States)

Bello-Pérez, L A; Contreras-Ramos, S M; Jìmenez-Aparicio, A; Paredes-López, O

2000-01-01

Banana native starch was acetylated and some of its functional properties were evaluated and compared to corn starch. In general, acetylated banana starch presented higher values in ash, protein and fat than corn acetylated starch. The modified starches had minor tendency to retrogradation assessed as % transmittance of starch pastes. At high temperature acetylated starches presented a water retention capacity similar to their native counterpart. The acetylation considerably increased the solubility of starches, and a similar behavior was found for swelling power. When freeze-thaw stability was studied, acetyl banana starch drained approximately 60% of water in the first and second cycles, but in the third and fourth cycles the percentage of separated water was low. However, acetyl corn starch showed lower freeze-thaw stability than the untreated sample. The modification increased the viscosity of banana starch pastes.

Graft polymerization of vinyl acetate onto starch. Saponification to starch-g-poly(vinyl alcohol)

International Nuclear Information System (INIS)

Fanta, G.F.; Burr, R.C.; Doane, W.M.; Russell, C.R.

1979-01-01

Graft polymerizations of vinyl acetate onto granular cornstarch were initiated by cobalt-60 irradiation of starch-monomer-water mixtures, and ungrafted poly(vinyl acetate) was separated from the graft copolymer by benzene extraction. Conversions of monomer to polymer were quantitative at a radiation dose of 1.0 Mrad. Over half of the polymer was present as ungrafted poly(vinyl acetate) (grafting efficiency less than 50%), and the graft copolymer contained only 34% grafted synthetic polymer (34% add-on). Lower irradiation doses produced lower conversions of monomer to polymer and gave graft copolymers with lower % add-on. Addition of minor amounts of acrylamide, methyl acrylate, and methacrylic acid as comonomers produced only small increases in % add-on and grafting efficency. Grafting efficiency was increased to 70% when a monomer mixture containing about 10% methyl methacrylate was used. Grafting efficiency could be increased to over 90% if the graft polymerization of vinyl acetate--methyl methacrylate was carried out near 0 0 C; although conversion of monomers to polymer was low and grafted polymer contained 40 to 50% poly(methyl methacrylate). Selected graft copolymers were treated with methanolic sodium hydroxide to convert starch-g-poly(vinyl acetate) to starch-g-poly(vinyl alcohol). The molecular weight of the poly(vinyl alcohol) moiety was about 30,000. The solubility of starch-g-poly(vinyl alcohol) in hot water was less than 50; however, solubility could be increased by substituting either acid-modified or hypochlorite-oxidized for unmodified starch in the graft polymerization reaction. Vinyl acetate was also graft polymerized onto acid-modified starch which had been dispersed and partially solubilized by heating in water. A total irradiation dose of either 1.0 or 0.5 Mrad gave starch-g-poly

Effects of acid-hydrolysis and hydroxypropylation on functional properties of sago starch.

Science.gov (United States)

Fouladi, Elham; Mohammadi Nafchi, Abdorreza

2014-07-01

In this study, sago starch was hydrolyzed by 0.14M HCl for 6, 12, 18, and 24h, and then modified by propylene oxide at a concentration of 0-30% (v/w). The effects of hydrolysis and etherification on molecular weight distribution, physicochemical, rheological, and thermal properties of dually modified starch were estimated. Acid hydrolysis of starch decreased the molecular weight of starch especially amylopectin, but hydroxypropylation had no effect on the molecular weight distribution. The degree of Molar substitution (DS) of hydroxypropylated starch after acid hydrolysis ranged from 0.007 to 0.15. Dually modified starch with a DS higher than 0.1 was completely soluble in cold water at up to 25% concentration of the starch. This study shows that hydroxypropylation and hydrolysis have synergistic effects unlike individual modifications. Dually modified sago starch can be applied to dip-molding for food and pharmaceutical processing because of its high solubility and low tendency for retrogradation. Copyright © 2014 Elsevier B.V. All rights reserved.

Some physicochemical properties of dextrin produced by extrusion process

Directory of Open Access Journals (Sweden)

Achmat Sarifudin

2014-06-01

Full Text Available Dextrinization of corn starch by twin screw extruder was studied. The effect of extruder operating conditions (five different screw speeds: 35, 45, 55, 65, and 70; and three temperatures: 125, 130, and 135 °C on some physicochemical properties of dextrin (total soluble solid, water absorption index, water solubility index, and total color difference was investigated. Results showed that as the screw speed and temperature of extrusion were increased the water absorption index of dextrin tended to drop meanwhile the total soluble solid, water solubility index, and color were inclined to rise. The range of total soluble solid, water absorption index, water solubility index and total color difference was 2.1–4.6 Brix, 159–203%, 20–51%, 3.5–14.1, respectively.

The properties of poly(lactic acid)/starch blends with a functionalized plant oil: tung oil anhydride.

Science.gov (United States)

Xiong, Zhu; Li, Chao; Ma, Songqi; Feng, Jianxian; Yang, Yong; Zhang, Ruoyu; Zhu, Jin

2013-06-05

Bio-sourced polymers, polylactide (PLA) and starch, have been melt-blended by lab-scale co-extruder with tung oil anhydride (TOA) as the plasticizer. The ready reaction between the maleic anhydride on TOA and the hydroxyl on starch led TOA molecules to accumulate on starch and increased the compatibility of PLA/starch blends, which was confirmed by FT-IR analyses and SEM. The TOA could change the mechanical properties and physical behaviors of PLA/starch blends. DSC and DMA analysis show that the TOA layer on starch has an effect on the thermal behavior of PLA in the ternary blend. The enrichment of TOA on starch improves the toughness and impact strength of the PLA/starch blends. The adding amount of TOA in PLA/starch blends primarily determined the compatibility and mechanical properties of the resulted ternary blends. The tensile and impact fracture modes of the PLA/starch blend with or without TOA has also been investigated by SEM analysis. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Development of non-water soluble, ductile mung bean starch based edible film with oxygen barrier and heat sealability.

Science.gov (United States)

Rompothi, Onjira; Pradipasena, Pasawadee; Tananuwong, Kanitha; Somwangthanaroj, Anongnat; Janjarasskul, Theeranun

2017-02-10

This research determined the effects of starch concentration (3.5-5.0%w/w), and plasticizer [glycerol (0-30%w/w) or sorbitol (0-60%w/w)] on properties of mung bean starch (MBS) films. The result showed that increasing plasticizer concentration tended to decrease tensile strength (TS), elastic modulus (EM) and oxygen permeability (OP); but increase elongation (%E), solubility, water vapor permeability (WVP) and seal strength. The extent of those changes also depended on starch concentration. Glycerol provided better plasticizer efficiency than sorbitol. A bimodal melting endotherm of retrograded structure was evident in non-plasticized film. However, only a low temperature endotherm was observed in polyol-plasticized films, indicating a plasticizer-induced structural modification. The developed ductile MBS films, (TS of 7.14±0.95 to 46.30±3.09MPa, %E of 2.46±0.21 to 56.95±4.34% and EM of 16.29±3.40 to 1428.45±148.72MPa) with an OP of 0.2397±0.0365 to 1.1520±0.1782 ccmm/m 2 daykPa and seal strength up to 422.36±7.93N/m, demonstrated in this study indicate the potential for food packaging applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Application of extruded broken bean flour for formulation of gluten-free cake blends

Directory of Open Access Journals (Sweden)

Luciana de Oliveira Froes Gomes

2015-06-01

Full Text Available The aim of this study was to determine the physical and microbiological characteristics of extruded broken beans flour, in addition to developing mixtures for gluten-free cake with these flours, evaluating their technological and sensory quality. Gluten-free formulations were prepared with 45%, 60% and 75% of extruded broken beans. All analyzes of the flours and mixtures for cakes were performed according to standard techniques found in the literature. Sensory analyzes of cakes applied the 9-point structured hedonic scale. Results were submitted to variance analysis and comparison of means test (Tukey, p<0.05. The use of extruded broken beans improved the water absorbed and water solubility index of the mixtures for gluten-free cake, and for the lower viscosity and retrogradation when compared to the standard formulation. All cakes were accepted (rate ≥ 7 for all the analyzed attributes. From the technological and sensory standpoints, the development of gluten-free cake mixtures is feasible with up to 75% of extruded broken beans.

Relationships between dry matter content, ensiling, ammonia-nitrogen, and ruminal in vitro starch digestibility in high-moisture corn samples.

Science.gov (United States)

Ferraretto, L F; Taysom, K; Taysom, D M; Shaver, R D; Hoffman, P C

2014-05-01

The objectives of the study were (1) to determine relationships between high-moisture corn (HMC) dry matter (DM), ammonia-N [% of crude protein (CP)], and soluble CP concentrations, and pH, with 7-h ruminal in vitro starch digestibility (ivStarchD), and (2) to evaluate the effect of ensiling on pH, ammonia-N, soluble CP, and ivStarchD measurements in HMC. A data set comprising 6,131 HMC samples (55 to 80% DM) obtained from a commercial feed analysis laboratory was used for this study. Month of sample submittal was assumed to be associated with length of the ensiling period. Data for month of sample submittal were analyzed using Proc Mixed in SAS (SAS Institute Inc., Cary, NC) with month as a fixed effect. Regressions to determine linear and quadratic relationships between ivStarchD and ammonia-N, soluble CP, pH, and DM content were performed using Proc Mixed. The ivStarchD increased by 9 percentage units from October to August of the following year. Similar results were observed for ammonia-N and soluble CP with increases from 1.8 to 4.6% of CP and 31.3 to 46.4% of CP, respectively, from October to August of the following year. Ammonia-N was positively related to ivStarchD (R(2)=0.61). The DM content of HMC at silo removal was negatively related (R(2)=0.47) to ivStarchD with a decrease of 1.6 percentage units in ivStarchD per 1-percentage-unit increase in DM content. The pH of HMC was negatively related to ammonia-N (R(2)=0.53), soluble CP (R(2)=0.57), and ivStarchD (R(2)=0.51). Combined, ammonia-N, DM, soluble CP, and pH provided a good prediction of ivStarchD (adjusted R(2)=0.70). Increasing pH, ammonia-N, soluble CP, and ivStarchD values indicate that HMC may need up to 10 mo of ensiling to reach maximum starch digestibility. Ammonia-N, DM content, soluble CP concentration, and pH are good indicators of ruminal in vitro starch digestibility for high-moisture corn. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights

Functional Characterization of Bean Zaragoza Starch (Phaseolus Lunatus L. and Quantification of the Resistant Starch

Directory of Open Access Journals (Sweden)

Piedad M. Montero-Castillo

2013-06-01

Full Text Available Legumes are a potential source of starch, representing between 30 and 50% of its dry weight, this is an essential energy source for humans. Currently its use is widespread in the food industry as an additive or raw material in food compounds, due to its nutritional, functional properties as a thickening agent and stabilizer of suspensions and dispersions. We evaluated several functional properties of starch variety zaragoza red bean, was obtained initial gelatinization temperature and final (71°C (81°C respectively, the solubility was 8.3% at 90°C, swelling power was 6.6% at 80°C, and water retention capacity was 4.4% at 80°C. The apparent viscosity was evaluated between 20 and 75 °C giving as results viscosities between 1.096 and 0.98 Cp respectively. The results showed that the tested temperatures significantly affect the solubility, swelling power, water holding capacity and viscosity of the starch. The amylose and amylopectin content was 21.1% and 78.19%. Finally, was obtained 9,24% resistant starch and compared with other conventional non starchy sources in order to acquire new knowledge about this material native to the Colombian Caribbean coast.

Effect of castor oil enrichment layer produced by reaction on the properties of PLA/HDI-g-starch blends.

Science.gov (United States)

Xiong, Zhu; Zhang, Lisheng; Ma, Songqi; Yang, Yong; Zhang, Chuanzhi; Tang, Zhaobin; Zhu, Jin

2013-04-15

Blends of entirely bio-sourced polymers, namely polylactide (PLA) and starch, have been melt-compounded by lab-scale co-extruder with castor oil (CO) as a plasticizer. The enrichment of castor oil on starch had great effect on the properties of the blends. If the castor oil was mainly dispersed in PLA matrix, the properties of the blends were poor, but when the hexamethylenediisocyanate (HDI) was grafted on starch granules the ready reactions between the hydroxyl on CO and the isocyante on the HDI-grafted starch (HGSTs) brought CO molecules enriched on starch particles. DSC analysis shows that the CO layer on starch has a positive effect on the crystallization of PLA in the ternary blend. The accumulation of CO on starch greatly improves the toughness and impact strength of PLA/starch blends. The grafting content of HDI on the starch granules primarily determined the compatibility and properties of the resulted blends. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of Radiation on Mechanical Properties of Poly (butylene succinate) and Cassava Starch Blends

International Nuclear Information System (INIS)

Hemvichian, K.; Dechasasawat, K.; Kangsumrith, W.; Suwanmala, P.

2014-01-01

This research compared the effects of gamma and electron beam irradiation at different doses on the mechanical properties of polymer blends between poly(butylene succinate) (PBS) and cassava starch. Two types of starch were used to prepare thermoplastic starch (TPS), native cassava starch and hydrophobic starch. PBS/TPS blends were compounded at five different weight ratios using a twin-screw extruder. Mechanical properties and degradation were evaluated in comparison to unirradiated samples. Results indicated that the incorpora- tion of TPS prepared from native cassava starch decreased the mechanical properties of PBS/TPS blends, whereas the addition of TPS prepared from hydrophobic starch improved the mechanical properties of the blends. In addition, the maximum mechanical properties of PBS/TPS blends were achieved when samples were exposed to irradiation at 120 kGy. Using soil burial evaluation, the degradation rate of blends was found to increase with the addition of TPS. Therefore we have demonstrated in this study that the type of TPS and irradiation treatment can significantly alter the mechanical properties and degradation of PBS/TPS blends.

Impact of dietary fibre-enriched ready-to-eat extruded snacks on the postprandial glycaemic response of non-diabetic patients.

Science.gov (United States)

Brennan, Margaret A; Derbyshire, Emma J; Brennan, Charles S; Tiwari, Brijesh K

2012-05-01

Food intervention is a financially sensible way for prevention and treatment of diabetes. Extruded snack foods are considered high glycaemic products. Our previous research illustrated that postprandial glycaemic responses to snacks are manipulated by altering dietary fibre and starch contents. The current research assessed the effect of psyllium and oat bran on postprandial glycaemia and in vitro digestibility. Addition of psyllium fibre to extruded snack products significantly reduced both the in vitro and in vivo glycaemic responses of products compared to a control snack product recipe. Oat bran inclusion reduced in vitro starch digestibility but not in vivo glycaemic response. The inclusion of oat bran into the snack products appeared to extend the glycaemic response of individuals compared to the control snack, suggesting a possibility of prolonging glucose release and potentially affecting satiety responses. The positive effect in attenuating glucose response means that psyllium fibre could be a target for inclusion by the snack food industry to effectively manipulate postprandial glucose response of individuals. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Extruded rice flour as a gluten substitute in the poduction of rice bread].

Science.gov (United States)

Clerici, Maria Teresa Pedrosa Silva; El-Dash, Ahmed A

2006-09-01

Research regarding the production of gluten-free bread (GFB) is very important nutritionally, technically and economically speaking, both to celiac patients and to developing countries who import wheat. The main technological problem in the production of GFB is obtaining a gluten substitute that is both inexpensive and capable of retaining gas during bread fermentation and baking. The use of gelatinized starch as an alternative for gluten seems promising. In this project, rice bread was made using pregelatinized extruded rice flour as a gluten substitute. Pre-gelatinized rice flours (PRF) were manufactured in a single screw Brabender extruder, varying extrusion temperature (108-192 degrees C) and the moisture of the raw material (19.2 - 24.8%), and were used in a proportion of 10 g for every 100 g of raw rice flour, in the production of gluten-free bread. Results showed that rice flour extruded at a high temperature (180 degrees) and low moisture content (20%), rendered bread with the best technological characteristics, presenting crust and crumb color similar to those of conventional wheat bread, although with volume and texture not as satisfactory in the same comparison.

Extruded black gram flour: Partial substitute for improving quality characteristics of Indian traditional snack

Directory of Open Access Journals (Sweden)

Laxmi Ananthanarayan

2018-03-01

Full Text Available Background: During extrusion of black gram flour, formation of amylose-lipid complexes lowers down the gelatinization enthalpy of extrudates, and the partially gelatinized black gram starch leads to lowering down the water-holding capacity and alters functional properties resulting in changing quality attributes of the end product on frying/microwaving/roasting. Methods: Attempts have been made to improve the quality of an Indian traditional snack (e.g., papad by incorporating extruded black gram flour as partial substitute for raw (unextruded black gram flour. In present work, overall quality improvement was achieved by analyzing prefrying and postfrying characteristics (diameter, moisture content, expansion ratio, oil uptake, texture, and color of papad and physical properties (color and viscosity of fried oil. Results: Four different papad samples were prepared (control papads without addition of papadkhar, papads with use of 3% papadkhar, papads with incorporation of extruded black gram flour at 25% concentration, papads with incorporation of extruded black gram flour at 50% concentration along with 1% papadkhar and analyzed along standard market sample. Incorporation of extruded black gram flour in papad resulted in greater expansion with less oil uptake in fried papad. Further addition of extruded black gram flour permitted the use of lower concentration of papadkhar. After frying, the quality of oil was characterized after numerous frying cycles. Conclusion: Oil used for frying of papads containing highest concentration of papadkhar was effective only up to two frying cycles, after which color and viscosity increased significantly, adversely affecting the quality of fried oil. Keywords: Black gram flour, Extrusion, Prefrying and postfrying characteristics of papad, Quality of fried oil

Properties of retrograded and acetylated starch produced via starch extrusion or starch hydrolysis with pullulanase.

Science.gov (United States)

Kapelko, M; Zięba, T; Gryszkin, A; Styczyńska, M; Wilczak, A

2013-09-12

The aim of the present study was to determine the impact of serial modifications of starch, including firstly starch extrusion or hydrolysis with pullulanase, followed by retrogradation (through freezing and defrosting of pastes) and acetylation (under industrial conditions), on its susceptibility to amylolysis. The method of production had a significant effect on properties of the resultant preparations, whilst the direction and extent of changes depended on the type of modification applied. In the produced starch esters, the degree of substitution, expressed by the per cent of acetylation, ranged from 3.1 to 4.4 g/100 g. The acetylation had a significant impact on contents of elements determined with the atomic emission spectrometry, as it contributed to an increased Na content and decreased contents of Ca and K. The DSC thermal characteristics enabled concluding that the modifications caused an increase in temperatures and a decrease in heat of transition (or its lack). The acetylation of retrograded starch preparations increased their solubility in water and water absorbability. The modifications were found to exert various effects on the rheological properties of pastes determined based on the Brabender's pasting characteristics and flow curves determined with the use of an oscillatory-rotating viscosimeter. All starch acetates produced were characterized by ca. 40% resistance to amylolysis. Copyright © 2013 Elsevier Ltd. All rights reserved.

Single screw extrusion of apple pomace-enriched blends: Extrudate characteristics and determination of optimum processing conditions.

Science.gov (United States)

Singha, Poonam; Muthukumarappan, Kasiviswanathan

2018-07-01

Response surface methodology was used to investigate the single screw extrusion of apple pomace-defatted soy flour-corn grits blends and the product properties. Five different blends at a level of 0-20% w/w apple pomace were extrusion cooked with varied barrel and die temperature (100-140℃), screw speed (100-200 rpm), and feed moisture content (14-20% wet basis). Increasing apple pomace content in the blends significantly ( P extrudates. The expansion ratio increased with pomace inclusion level of 5% but decreased significantly ( P extruded snack products were at 140℃ barrel and die temperature, 20% feed moisture content, and 200 rpm screw speed. The results indicated active interaction between apple pomace and starch during expansion process.

Characterization of starch nanoparticles

Science.gov (United States)

Szymońska, J.; Targosz-Korecka, M.; Krok, F.

2009-01-01

Nanomaterials already attract great interest because of their potential applications in technology, food science and medicine. Biomaterials are biodegradable and quite abundant in nature, so they are favoured over synthetic polymer based materials. Starch as a nontoxic, cheap and renewable raw material is particularly suitable for preparation of nanoparticles. In the paper, the structure and some physicochemical properties of potato and cassava starch particles of the size between 50 to 100 nm, obtained by mechanical treatment of native starch, were presented. We demonstrated, with the aim of the Scanning Electron Microscopy (SEM) and the non-contact Atomic Force Microscopy (nc-AFM), that the shape and dimensions of the obtained nanoparticles both potato and cassava starch fit the blocklets - previously proposed as basic structural features of native starch granules. This observation was supported by aqueous solubility and swelling power of the particles as well as their iodine binding capacity similar to those for amylopectin-type short branched polysaccharide species. Obtained results indicated that glycosidic bonds of the branch linkage points in the granule amorphous lamellae might be broken during the applied mechanical treatment. Thus the released amylopectin clusters could escape out of the granules. The starch nanoparticles, for their properties qualitatively different from those of native starch granules, could be utilized in new applications.

A Miniaturized Extruder to Prototype Amorphous Solid Dispersions: Selection of Plasticizers for Hot Melt Extrusion.

Science.gov (United States)

Lauer, Matthias E; Maurer, Reto; Paepe, Anne T De; Stillhart, Cordula; Jacob, Laurence; James, Rajesh; Kojima, Yuki; Rietmann, Rene; Kissling, Tom; van den Ende, Joost A; Schwarz, Sabine; Grassmann, Olaf; Page, Susanne

2018-05-19

Hot-melt extrusion is an option to fabricate amorphous solid dispersions and to enhance oral bioavailability of poorly soluble compounds. The selection of suitable polymer carriers and processing aids determines the dissolution, homogeneity and stability performance of this solid dosage form. A miniaturized extrusion device (MinEx) was developed and Hypromellose acetate succinate type L (HPMCAS-L) based extrudates containing the model drugs neurokinin-1 (NK1) and cholesterylester transfer protein (CETP) were manufactured, plasticizers were added and their impact on dissolution and solid-state properties were assessed. Similar mixtures were manufactured with a lab-scale extruder, for face to face comparison. The properties of MinEx extrudates widely translated to those manufactured with a lab-scale extruder. Plasticizers, Polyethyleneglycol 4000 (PEG4000) and Poloxamer 188, were homogenously distributed but decreased the storage stability of the extrudates. Stearic acid was found condensed in ultrathin nanoplatelets which did not impact the storage stability of the system. Depending on their distribution and physicochemical properties, plasticizers can modulate storage stability and dissolution performance of extrudates. MinEx is a valuable prototyping-screening method and enables rational selection of plasticizers in a time and material sparing manner. In eight out of eight cases the properties of the extrudates translated to products manufactured in lab-scale extrusion trials.

Morphological, mechanical, barrier and properties of films based on acetylated starch and cellulose from barley.

Science.gov (United States)

El Halal, Shanise Lisie Mello; Colussi, Rosana; Biduski, Bárbara; Evangelho, Jarine Amaral do; Bruni, Graziella Pinheiro; Antunes, Mariana Dias; Dias, Alvaro Renato Guerra; Zavareze, Elessandra da Rosa

2017-01-01

Biodegradable films of native or acetylated starches with different concentrations of cellulose fibers (0%, 10% and 20%) were prepared. The films were characterized by morphological, mechanical, barrier, and thermal properties. The tensile strength of the acetylated starch film was lower than those of the native starch film, without fibers. The addition of fibers increased the tensile strength and decreased the elongation and the moisture of native and acetylated starches films. The acetylated starch film showed higher water solubility when compared to native starch film. The addition of cellulose fibers reduced the water solubility of the acetylated starch film. The films reinforced with cellulose fiber exhibited a higher initial decomposition temperature and thermal stability. The mechanical, barrier, solubility, and thermal properties are factors which direct the type of the film application in packaging for food products. The films elaborated with acetylated starches of low degree of substitution were not effective in a reduction of the water vapor permeability. The addition of the cellulose fiber in acetylated and native starches films can contribute to the development of more resistant films to be applied in food systems that need to maintain their integrity. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Hydroxypropylation of pigeon pea (cajanus cajan) starch: Preparation, functional characterizations and enzymatic digestibility

International Nuclear Information System (INIS)

Lawal, O.S.

2008-05-01

Hydroxypropyl starch derivatives were prepared from pigeon pea starch (NPPS) which is an unconventional starch source. Functional parameters and characterization of both native and modified starches were carried out. The starch granules appeared oval or elliptical in shape with sizes ranging from 7 - 40 μm in width and 10 . 30 μm in length. Hydroxypropylation did not alter the shape of the starch granules in a pronounced way. Generally, the x-ray diffractograms of both native and hydroxypropyl derivatives showed the 'C' pattern. However, slight reductions were observed in the intensity of starches after modification. At all temperatures studied (30 - 90 deg. C), swelling and solubility of hydroxypropylated starches were higher than the NPPS. Progressive increases in swelling capacity and solubility were observed as the MS increased among the hydroxypropylated starches. Hydroxypropylation reduced starch paste turbidity on storage. Also, studies showed that syneresis reduced after hydroxypropylation. In addition, syneresis reduced as the MS of the hydroxypropyl starches increased. The results indicate that pasting temperature and peak temperature reduced after modification but peak viscosity increased in hydroxypropylated starch derivatives compared with the native starch. Setback reduced in hydroxypropylated starches compared with the native starch. Enthalpy of gelatinization and percentage retrogradation reduced after hydroxypropylation and progressive reductions were observed as the MS increased among the starch derivatives. Hydroxypropylation increased enzymatic digestibility. (author)

Potential of Starch Nanocomposites for Biomedical Applications

Science.gov (United States)

Zakaria, N. H.; Muhammad, N.; Abdullah, M. M. A. B.

2017-06-01

In recent years, the development of biodegradable materials from renewable sources based on polymeric biomaterials have grown rapidly due to increase environmental concerns and the shortage of petroleum sources. In this regard, naturally renewable polymers such as starch has shown great potential as environmental friendly materials. Besides, the unique properties of starch such as biodegradable and non-toxic, biocompatible and solubility make them useful for a various biomedical applications. Regardless of their unique properties, starch materials are known to have limitations in term of poor processability, low mechanical properties, poor long term stability and high water sensitivity. In order to overcome these limitations, the incorporation of nano size fillers into starch materials (nanocomposites) has been introduced. This review aims to give an overview about structure and characteristics of starch, modification of starch by nanocomposites and their potential for biomedical applications.

Influence of lidocaine forms (salt vs. freebase) on properties of drug-Eudragit® L100-55 extrudates prepared by reactive melt extrusion.

Science.gov (United States)

Liu, Xu; Ma, Xiangyu; Kun, Eucharist; Guo, Xiaodi; Yu, Zhongxue; Zhang, Feng

2018-06-05

This study examines the preparation of sustained-release lidocaine polyelectrolyte complex using reactive melt extrusion. Eudragit L100-55 was selected as the ionic polymer. The influence of drug forms (freebase vs. hydrochloride salt) on lidocaine-Eudragit L100-55 interactions, physical stability, and dissolution properties of extrudates was investigated. It was confirmed by DSC, FT-IR and Raman spectroscopy that polyelectrolyte could only form via the acid-base reaction between Eudragit L100-55 and lidocaine freebase. Due to this ionic interaction, the lidocaine extrudate was physically more stable than the lidocaine hydrochloride extrudate during the storage under stressed condition. Drug release from lidocaine extrudate was a function of drug solubility, polymer solubility, drug-polymer interaction, and drug-induced microenvironment pH. At 30% drug loading, extrudate exhibited sustained release in aqueous media at pH 1.2 and 4.5. Due to the alkaline microenvironment pH induced by dissolved lidocaine, Eudragit L100-55 was solubilized and sustained-release was not achieved in water and aqueous media at pH 5.5. In comparison, lidocaine hydrochloride induced an acidic microenvironment. Drug release of lidocaine hydrochloride extrudate was similar at pH 1.2, 4.5, 5.5 and water with drug being released over 10 hours. The release of lidocaine hydrochloride from the extrudates in these media was primarily controlled by microenvironment pH. It is concluded that different forms of lidocaine resulted in different drug-polymer interactions and distinctive physicochemical properties of extrudates. Copyright © 2018. Published by Elsevier B.V.

Effect of ionizing radiation on starch and cellulose

International Nuclear Information System (INIS)

Klenha, J.; Bockova, J.

1973-09-01

The investigation is reported of the effects of ionizing radiation both on macromolecular systems generally and on polysaccharides, starch and cellulose. Attention is focused on changes in the physical and physico-chemical properties of starch and cellulose, such as starch swelling, gelation, viscosity, solubility, reaction with iodine, UV, IR and ESR spectra, chemical changes resulting from radiolysis and from the effect of amylases on irradiated starch, changes in cellulose fibre strength, water absorption, stain affinity, and also the degradation of cellulose by radiation and the effect of cellulases on irradiated cellulose. Practical applications of the findings concerning cellulose degradation are discussed. (author)

Irradiated gelatin-potato starch blends: evaluation of physicochemical properties

International Nuclear Information System (INIS)

Inamura, Patricia Y.; Regis, Wellington; Mastro, Nelida L.

2015-01-01

Macromolecular polysaccharides of large chains as starch can interlace with gelatin modifying their mechanical resistance. In this work, biodegradable bovine gelatin-potato starch blends films were developed using glycerol as plasticizer. Three formulations of gelatin/starch proportions (w/w) were used (1:0; 3:1; 1:1) and casting was the chosen method. The dried samples were then submitted to ionizing radiation coming from an electron beam (EB) accelerator with doses of 20 and 40 kGy, at room temperature, in the presence of air. Mechanical properties such as puncture strength and elongation at break were measured. Color measurements, water absorption, moisture, and film solubility were assessed. The results showed that starch addition to films based on gelatin as well as irradiation affected physical and structural properties of the films. Although the increase of starch content in the mixture led to decrease of the puncture force even in samples irradiated with the higher dose, there was a decrease of water absorption of films with the increase of the dose, and also by the higher starch content. Samples irradiated at 20 kGy presented higher moisture and film solubility. The methodology developed in this paper can be applied to other composite systems to establish the best protein:starch ratio, and the contribution of the radiation crosslinking in each specific case. (author)

Irradiated gelatin-potato starch blends: evaluation of physicochemical properties

Energy Technology Data Exchange (ETDEWEB)

Inamura, Patricia Y.; Regis, Wellington; Mastro, Nelida L., E-mail: nlmastro@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2015-07-01

Macromolecular polysaccharides of large chains as starch can interlace with gelatin modifying their mechanical resistance. In this work, biodegradable bovine gelatin-potato starch blends films were developed using glycerol as plasticizer. Three formulations of gelatin/starch proportions (w/w) were used (1:0; 3:1; 1:1) and casting was the chosen method. The dried samples were then submitted to ionizing radiation coming from an electron beam (EB) accelerator with doses of 20 and 40 kGy, at room temperature, in the presence of air. Mechanical properties such as puncture strength and elongation at break were measured. Color measurements, water absorption, moisture, and film solubility were assessed. The results showed that starch addition to films based on gelatin as well as irradiation affected physical and structural properties of the films. Although the increase of starch content in the mixture led to decrease of the puncture force even in samples irradiated with the higher dose, there was a decrease of water absorption of films with the increase of the dose, and also by the higher starch content. Samples irradiated at 20 kGy presented higher moisture and film solubility. The methodology developed in this paper can be applied to other composite systems to establish the best protein:starch ratio, and the contribution of the radiation crosslinking in each specific case. (author)

Characterization of starch-based bioplastics from jackfruit seed plasticized with glycerol.

Science.gov (United States)

Santana, Renata Ferreira; Bonomo, Renata Cristina Ferreira; Gandolfi, Olga Reinert Ramos; Rodrigues, Luciano Brito; Santos, Leandro Soares; Dos Santos Pires, Ana Clarissa; de Oliveira, Cristiane Patrícia; da Costa Ilhéu Fontan, Rafael; Veloso, Cristiane Martins

2018-01-01

Biodegradable films based on starches from different botanical sources exhibited physicochemical and functional properties which were related with the starch characteristics. However, had inadequate mechanical properties and were hard and brittle. In this research, jackfruit seed starch plasticized with glycerol were developed and characterized. The starch and glycerol concentrations ranged from 2 to 6% w/w and 20 to 60 g/100 g starch, respectively. Bioplastics were obtained by the casting method and characterized in terms of color, mechanical properties, solubility, water vapor permeability ( WVP ), morphology and free energy of the hydrophobic interaction. Electronic micrographics showed the presence of some intact starch granules. The bioplastics were hydrophilic and those of 6% starch and 40% glycerol were the most hydrophilic ([Formula: see text] = 41.35 mJ m -1 ). The solubility of the films presented a direct relationship with the starch concentration ranging from 16.42 to 23.26%. Increased opacity and color difference were observed with increasing starch concentration. The WVP ranged from 1.374 × 10 -3 to 3.07 × 10 -4  g m/day m 2 which was positively related with the concentration of starch and glycerol. Tensile strength, percent elongation and Young's Modulus indicated that the jackfruit starch and glycerol provided a film with good mechanical properties. The results replaced that jackfruit starch can be used to develop films, with low opacity, moderate WVP and relatively high mechanical stability, by using glycerol in the gelatinized starch dispersions.

Defatted flaxseed meal incorporated corn-rice flour blend based extruded product by response surface methodology.

Science.gov (United States)

Ganorkar, Pravin M; Patel, Jhanvi M; Shah, Vrushti; Rangrej, Vihang V

2016-04-01

Considering the evidence of flaxseed and its defatted flaxseed meal (DFM) for human health benefits, response surface methodology (RSM) based on three level four factor central composite rotatable design (CCRD) was employed for the development of DFM incorporated corn - rice flour blend based extruded snack. The effect of DFM fortification (7.5-20 %), moisture content of feed (14-20 %, wb), extruder barrel temperature (115-135 °C) and screw speed (300-330 RPM) on expansion ratio (ER), breaking strength (BS), overall acceptability (OAA) score and water solubility index (WSI) of extrudates were investigated using central composite rotatable design (CCRD). Significant regression models explained the effect of considered variables on all responses. DFM incorporation level was found to be most significant independent variable affecting on extrudates characteristics followed by extruder barrel temperature and then screw rpm. Feed moisture content did not affect extrudates characteristics. As DFM level increased (7.5 % to 20 %), ER and OAA value decreased. However, BS and WSI values were found to increase with increase in DFM level. Based on the defined criteria for numerical optimization, the combination for the production of DFM incorporated extruded snack with desired sensory attributes was achieved by incorporating 10 % DFM (replacing rice flour in flour blend) and by keeping 20 % moisture content, 312 screw rpm and 125 °C barrel temperature.

Effect of enzymatic (thermostable α-amylase) treatment on the physicochemical and antioxidant properties of extruded rice incorporated with soybean flour.

Science.gov (United States)

Xu, Enbo; Wu, Zhengzong; Pan, Xiaowei; Long, Jie; Wang, Fang; Xu, Xueming; Jin, Zhengyu; Jiao, Aiquan

2016-04-15

In order to determine the effect of enzymatic extrusion on the physicochemical and antioxidant properties of rice/soybean mixture, different mass ratios (100/0, 95/5, 85/15, 70/30, 50/50 and 25/75%, w/w) were treated with thermostable α-amylase. The reduced special mechanical energy and the enhanced product temperature were closely and regularly linked with the increase of soybean content. The bulk density and water solubility index increased, and the water absorption index and viscosities decreased remarkably after enzymatic extrusion, however, the modification caused by α-amylase were dramatically eliminated with the increase of soybean content to ∼50%. Moreover, the addition of enzyme exhibited an improvement of the total phenolic/flavonoid content (TPC/TFC) and antioxidant capacities compared to traditional extrusion. The TPC/TFC retention of extrudate (ratios of 85/15 and 70/30%) attained over 90%, but dramatically decreased (72.91 and 67.81%, respectively) with soybean added to 75%, probably due to the great reduction of starch substrate for enzymatic hydrolysis. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

Measurement of Thermal Properties of Triticale Starch Films Using Photothermal Techniques

Science.gov (United States)

Correa-Pacheco, Z. N.; Cruz-Orea, A.; Jiménez-Pérez, J. L.; Solorzano-Ojeda, S. C.; Tramón-Pregnan, C. L.

2015-06-01

Nowadays, several commercially biodegradable materials have been developed with mechanical properties similar to those of conventional petrochemical-based polymers. These materials are made from renewable sources such as starch, cellulose, corn, and molasses, being very attractive for numerous applications in the plastics, food, and paper industries, among others. Starches from maize, rice, wheat, and potato are used in the food industry. However, other types of starches are not used due to their low protein content, such as triticale. In this study, starch films, processed using a single screw extruder with different compositions, were thermally and structurally characterized. The thermal diffusivity, thermal effusivity, and thermal conductivity of the biodegradable films were determined using photothermal techniques. The thermal diffusivity was measured using the open photoacoustic cell technique, and the thermal effusivity was obtained by the photopyroelectric technique in an inverse configuration. The results showed differences in thermal properties for the films. Also, the films microstructures were observed by scanning electron microscopy, transmission electron microscopy, and the crystalline structure determined by X-ray diffraction.

Process optimization of ultrasound-assisted alcoholic-alkaline treatment for granular cold water swelling starches.

Science.gov (United States)

Zhu, Bo; Liu, Jianli; Gao, Weidong

2017-09-01

This paper reports on the process optimization of ultrasonic assisted alcoholic-alkaline treatment to prepare granular cold water swelling (GCWS) starches. In this work, three statistical approaches such as Plackett-Burman, steepest ascent path analysis and Box-Behnken design were successfully combined to investigate the effects of major treatment process variables including starch concentration, ethanol volume fraction, sodium hydroxide dosage, ultrasonic power and treatment time, and drying operation, that is, vacuum degree and drying time on cold-water solubility. Results revealed that ethanol volume fraction, sodium hydroxide dosage, applied power and ultrasonic treatment time were significant factors that affected the cold-water solubility of GCWS starches. The maximum cold-water solubility was obtained when treated at 400W of applied power for 27.38min. Optimum volume fraction of ethanol and sodium hydroxide dosage were 66.85% and 53.76mL, respectively. The theoretical values (93.87%) and the observed values (93.87%) were in reasonably good agreement and the deviation was less than 1%. Verification and repeated trial results indicated that the ultrasound-assisted alcoholic-alkaline treatment could be successfully used for the preparation of granular cold water swelling starches at room temperatures and had excellent improvement on the cold-water solubility of GCWS starches. Copyright © 2016. Published by Elsevier B.V.

Fragrant starch-based films with limonene

Directory of Open Access Journals (Sweden)

Adrian K. Antosik

2017-02-01

Full Text Available Novel fragrant starch-based films with limonene were successfully prepared. Biodegradable materials of natural origin were used and the process was relatively simple and inexpensive. The effect of limonene on physicochemical properties of starch-based films (moisture absorption, solubility in water, wettability, mechanical properties were compared to glycerol plasticized system. Taking into consideration that the obtained materials could also exhibit bactericidal and fungicidal properties, the studies with Escherichia coli, Candida albicans and Aspergillus niger were performed. Such a material could potentially find application in food packaging (e.g. masking unpleasant odors, hydrophilic starch film would prevent food drying, or in agriculture (e.g. for seed encapsulated tapes.

Starch-degrading enzymes from anaerobic non-clostridial bacteria

Energy Technology Data Exchange (ETDEWEB)

Weber, H; Schepers, H J; Troesch, W [Fraunhofer-Institut fuer Grenzflaechen- und Bioverfahrenstechnik (IGB), Stuttgart (Germany, F.R.)

1990-08-01

A number of meso- and thermophilic anaerobic starch-degrading non-spore-forming bacteria have been isolated. All the isolates belonging to different genera are strictly anaerobic, as indicated by a catalase-negative reaction, and produce soluble starch-degrading enzymes. Compared to enzymes of aerobic bacteria, those of anaerobic origin mainly show low molecular mass of about 25 000 daltons. Some of the enzymes may have useful applications in the starch industry because of their unusual product pattern, yielding maltotetraose as the main hydrolysis product. (orig.).

Xylanase and Protease Increase Solubilization of Non-Starch Polysaccharides and Nutrient Release of Corn- and Wheat Distillers Dried Grains with Solubles

DEFF Research Database (Denmark)

Pedersen, Mads Brøgger; Dalsgaard, Søren; Arent, Susan

2015-01-01

The use of distiller dried grains with solubles (DDGS) as alternative to conventional animal feed for non-ruminants is challenged by the high content of non-starch polysaccharides and varying protein quality. In this study the enzymatic degradation of corn- and wheat DDGS was evaluated, in vitro...... of this xylanase. The current in vitro results indicate a high potential of xylanase in combination with protease to efficiently degrade DDGS and promote nutrient release in diets for non-ruminant animals....

Acetylated rice starches films with different levels of amylose: Mechanical, water vapor barrier, thermal, and biodegradability properties.

Science.gov (United States)

Colussi, Rosana; Pinto, Vânia Zanella; El Halal, Shanise Lisie Mello; Biduski, Bárbara; Prietto, Luciana; Castilhos, Danilo Dufech; Zavareze, Elessandra da Rosa; Dias, Alvaro Renato Guerra

2017-04-15

Biodegradable films from native or acetylated starches with different amylose levels were prepared. The films were characterized according to the mechanical, water vapor barrier, thermal, and biodegradability properties. The films from acetylated high amylose starches had higher moisture content and water solubility than the native high amylose starch film. However, the acetylation did not affect acid solubility of the films, regardless of the amylose content. Films made from high and medium amylose rice starches were obtained; however low amylose rice starches, whether native or acetylated, did not form films with desirable characteristics. The acetylation decreased the tensile strength and increased the elongation of the films. The acetylated starch-based films had a lower decomposition temperature and higher thermal stability than native starch films. Acetylated starches films exhibited more rapid degradation as compared with the native starches films. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of feed composition, moisture content and extrusion temperature on extrudate characteristics of yam-corn-rice based snack food.

Science.gov (United States)

Seth, Dibyakanta; Badwaik, Laxmikant S; Ganapathy, Vijayalakshmi

2015-03-01

Blends of yam, rice and corn flour were processed in a twin-screw extruder. Effects of yam flour (10-40 %), feed moisture content (12-24 %) and extruder barrel temperature (100-140 °C) on the characteristics of the dried extrudates was investigated using a statistical technique response surface methodology (RSM). Radial expansion ratio differed significantly (p ≤ 0.05) with change in all the independent variables. Highest expansion (3.97) was found at lowest moisture content (12 %) and highest barrel temperature (140 °C). Increased yam flour level decreased the expansion ratio significantly. Water absorption index (WAI) increased significantly with increase of all variables. However, water solubility index (WSI) did not change with change in yam flour percent. Hardness of extrudates that varied from 3.86 to 6.94 N was positively correlated with yam flour level and feed moisture content, however it decreased significantly (p ≤ 0.001) with increase of barrel temperature. Yam percent of 15.75 with feed moisture and barrel temperature at 12.00 % and 140 °C respectively gave an optimized product of high desirability (> 0.90) with optimum responses of 3.29 expansion ratio, 5.64 g/g dry solid water absorption index, 30.39 % water solubility index and 3.86 N hardness. The predicted values registered non-significant (p extruded snacks and little emphasis on the chemistry of interaction between different components.

The effect of moisture content on physicochemical properties of extruded waxy and non-waxy rice flour.

Science.gov (United States)

Jongsutjarittam, Ornpicha; Charoenrein, Sanguansri

2014-12-19

The properties of waxy rice flour (WRF) and non-waxy rice flour (RF) were modified using an extrusion process with different feeding material moisture contents. WRF was more affected by the thermomechanical stress from extrusion; consequently, it had a lower glass transition temperature but higher water solubility index (WSI) indicating higher molecular degradation than extruded RF. The lower moisture content of the feeding flour caused more severe flour damage (coarser surface of the extruded flour) and lowered relative crystallinity compared to higher moisture content processing. Moreover, low moisture content processing led to complete gelatinization, whereas, partial gelatinization occurred in the higher moisture content extrusion. Consequently, the extruded flours had a lower peak viscosity and gelatinization enthalpy but a higher water absorption index and WSI than native flour. In conclusion, the rice flour type and the moisture content of the extrusion feeding flour affected the physicochemical properties of the extruded flour. Copyright © 2014 Elsevier Ltd. All rights reserved.

Physical properties of snacks made from cassava leaf flour

Directory of Open Access Journals (Sweden)

Adriana Cristina Ferrari

2014-02-01

Full Text Available The food industry is continually growing with new products becoming available every year. Extrusion combines a number of unit operations in one energy efficient rapid continuous process and can be used to produce a wide variety of snacks foods. The objective of this study was to evaluate the effect of extrusion temperature, screw speed, and amount of cassava leaf flour mixed with cassava starch on the physical properties of extruded snacks processed using a single screw extruder. A central composite rotational design, including three factors with 20 treatments, was used in the experimental design. Dependent variables included the expansion index, specific volume, color, water absorption index, and water solubility index. Among the parameters examined, the amount of cassava leaf flour and extrusion temperature showed significant effects on extruded snack characteristics. Mixtures containing 10% of cassava leaf flour extruded at 100°C and 255 rpm shows favorable levels of expansion, color, water absorption index, and water solubility index.

Extrudability and Consolidation of Blends between CGM and DDGS

Directory of Open Access Journals (Sweden)

C. J. R. Verbeek

2016-01-01

Full Text Available During the last decade, the global biofuels industry has experienced exponential growth. By-products such as high protein corn gluten meal (CGM and high fibre distillers dried grains with solubles (DDGS have grown in parallel. CGM has been shown to be suitable as a biopolymer; the high fibre content of DDGS reduces its effectiveness, although it is considerably cheaper. In this study, the processing behaviour of CGM and DDGS blends was evaluated and resulting extrudate properties were determined. Prior to processing, urea was used as a denaturant. DDGS : CGM ratios of 0, 33, 50, 66, and 100% were processed in a single screw extruder, which solely used dissipative heating. Blends containing DDGS were less uniformly consolidated and resulted in more dissipative heating. Blends showed multiple glass transitions, which is characteristic of mechanically compatible blends. Transmission electron microscopy revealed phase separation on a microscale, although distinct CGM or DDGS phases could not be identified. On a macroscale, optical microscopy suggested that CGM-rich blends were better consolidated, supported by visual observations of a more continuous extrudate formed during extrusion. Future work should aim to also characterize the mechanical properties of these blends to assess their suitability as either bioplastic feedstock or pelletized livestock feed.

Water Absorption and Thermomechanical Characterization of Extruded Starch/Poly(lactic acid/Agave Bagasse Fiber Bioplastic Composites

Directory of Open Access Journals (Sweden)

F. J. Aranda-García

2015-01-01

Full Text Available Water absorption and thermomechanical behavior of composites based on thermoplastic starch (TPS are presented in this work, wherein the concentration of agave bagasse fibers (ABF, 0–15 wt% and poly(lactic acid (PLA, 0–30 wt% is varied. Glycerol (G is used as starch (S plasticizer to form TPS. Starch stands as the polymer matrix (70/30 wt/wt, S/G. The results show that TPS hygroscopicity decreases as PLA and fiber content increase. Storage, stress-strain, and flexural moduli increase with PLA and/or agave bagasse fibers (ABF content while impact resistance decreases. The TPS glass transition temperature increases with ABF content and decreases with PLA content. Micrographs of the studied biocomposites show a stratified brittle surface with a rigid fiber fracture.

Maltase-glucoamylase modulates gluconeogenesis and sucrase-isomaltase dominates starch digestion glucogenesis

Science.gov (United States)

Six enzyme activities are needed to digest starch to absorbable free glucose; 2 luminal alpha-amylases (AMY) and 4 mucosal maltase-glucoamylase (MGAM) and sucrase-isomaltase (SI) subunit activities are involved in the digestion. The AMY activities break down starch to soluble oligomeric dextrins; mu...

Synthesis and characterization of rice starch laurate as food-grade emulsifier for canola oil-in-water emulsions.

Science.gov (United States)

García-Tejeda, Y V; Leal-Castañeda, E J; Espinosa-Solis, V; Barrera-Figueroa, V

2018-08-15

The effect of esterification on hydrolyzed rice starch was analyzed, for this aim rice starch was hydrolyzed and subsequently esterified with lauroyl chloride at three modification levels. Starch derivatives were characterized regarding their degree of substitution (DS), water solubility index, z-potential, gelatinization, and digestibility properties. DS of derivatives of rice starch laurate ranged from 0.042 to 1.86. It was determined that after esterification the water solubility index increased from 3.44 to 53.61%, the z-potential decreased from -3.18 to -11.27, and the content of slowly digestible starch (SDS) decreased from 26.22 to 5.13%. Different emulsions with starch concentrations ranging from 6 to 30 wt% were evaluated. The most stable emulsions were those having 20 and 30 wt% of rice starch laurate. Copyright © 2018 Elsevier Ltd. All rights reserved.

Biochemical Characterization of the Lactobacillus reuteri Glycoside Hydrolase Family 70 GTFB Type of 4,6-α-Glucanotransferase Enzymes That Synthesize Soluble Dietary Starch Fibers.

Science.gov (United States)

Bai, Yuxiang; van der Kaaij, Rachel Maria; Leemhuis, Hans; Pijning, Tjaard; van Leeuwen, Sander Sebastiaan; Jin, Zhengyu; Dijkhuizen, Lubbert

2015-10-01

4,6-α-Glucanotransferase (4,6-α-GTase) enzymes, such as GTFB and GTFW of Lactobacillus reuteri strains, constitute a new reaction specificity in glycoside hydrolase family 70 (GH70) and are novel enzymes that convert starch or starch hydrolysates into isomalto/maltopolysaccharides (IMMPs). These IMMPs still have linear chains with some α1→4 linkages but mostly (relatively long) linear chains with α1→6 linkages and are soluble dietary starch fibers. 4,6-α-GTase enzymes and their products have significant potential for industrial applications. Here we report that an N-terminal truncation (amino acids 1 to 733) strongly enhances the soluble expression level of fully active GTFB-ΔN (approximately 75-fold compared to full-length wild type GTFB) in Escherichia coli. In addition, quantitative assays based on amylose V as the substrate are described; these assays allow accurate determination of both hydrolysis (minor) activity (glucose release, reducing power) and total activity (iodine staining) and calculation of the transferase (major) activity of these 4,6-α-GTase enzymes. The data show that GTFB-ΔN is clearly less hydrolytic than GTFW, which is also supported by nuclear magnetic resonance (NMR) analysis of their final products. From these assays, the biochemical properties of GTFB-ΔN were characterized in detail, including determination of kinetic parameters and acceptor substrate specificity. The GTFB enzyme displayed high conversion yields at relatively high substrate concentrations, a promising feature for industrial application. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Some Nutritional Characteristics of Enzymatically Resistant Maltodextrin from Cassava (Manihot esculenta Crantz) Starch.

Science.gov (United States)

Toraya-Avilés, Rocío; Segura-Campos, Maira; Chel-Guerrero, Luis; Betancur-Ancona, David

2017-06-01

Cassava (Manihot esculenta Crantz) native starch was treated with pyroconversion and enzymatic hydrolysis to produce a pyrodextrin and an enzyme-resistant maltodextrin. Some nutritional characteristics were quantified for both compounds. Pyroconversion was done using a 160:1 (p/v) starch:HCl ratio, 90 °C temperature and 3 h reaction time. The resulting pyrodextrin contained 46.21% indigestible starch and 78.86% dietary fiber. Thermostable α-amylase (0.01%) was used to hydrolyze the pyrodextrin at 95 °C for 5 min. The resulting resistant maltodextrin contained 24.45% dextrose equivalents, 56.06% indigestible starch and 86.62% dietary fiber. Compared to the cassava native starch, the pyrodextrin exhibited 56% solubility at room temperature and the resistant maltodextrin 100%. The glycemic index value for the resistant maltodextrin was 59% in healthy persons. Its high indigestible starch and dietary fiber contents, as well as its complete solubility, make the resistant maltodextrin a promising ingredient for raising dietary fiber content in a wide range of foods, especially in drinks, dairy products, creams and soups.

Biaxial vent extruder

International Nuclear Information System (INIS)

Idemoto, A.; Maki, Y.; Oda, N.

1981-01-01

A biaxial vent extruder is described for processing of slurry-like waste fluids or radioactive waste fluids which have a hopper cylinger, a solidifying substance port and a solidified substance port. A plurality of vent cylinders each having a vent port are provided with a plunger type scraper. An extruding cylinder having a single opening for a main screw is connected to the assembled vent cylinders. The main screw extends to the upstream end of the extruding cylinder and a sub-screw extends to the extruding cylinder. The screws each having a full flight engaging the other and a set of rings are mounted on the screws near the respective vent port inlets. The screws are rotated in different directions and inwardly with respect to the vent ports. Rotors may be mounted on the screws to break down solid particles

Optimization of Extrusion Process of Directly Expanded Snacks Based on Potato Starch in a Single Step for the Formation of Type IV Resistant Starch.

Science.gov (United States)

Calvo-López, Amira Daniela; Martínez-Bustos, Fernando

2017-09-01

Resistant starch type IV (RSIV) can be produced by chemical modifications (etherized or esterified) such as conversion, substitution, or cross-linking, which can prevent its digestion by blocking enzyme access and forming atypical linkages. In this research, the effects of barrel temperature (145.86-174.14 °C), the screw speed (42.93-57.07 Hz) and derivatization (esterification) in the formation of RSIV content of directly expanded snacks (second generation snacks) were studied. Potato starch was chemically modified by phosphorylation and succinylation, and expanded by using the extrusion cooking process. Snacks with phosphorylated starch showed expansion index from 2.57 to 3.23, bulk density from 306.19 to 479.00 kg/m 3 and RSIV from 43.27 to 55.81%. Snacks with succinylated starch had expansion index from 3.52 to 3.82, bulk density from 99.85 to 134.51 kg/m 3 and RSIV from 23.17 to 35.01%. The results found in this work showed that it is possible to manufacture extruded directly expanded snacks (second-generation snacks) such as a ready-to-eat (RTE) with good physicochemical properties and without substantial loss of extrusion functionality, which could bring a healthy benefit due to the presence of RSIV.

Experiment using laboratory scale extruder. Fluid behavior in twin-screw extruder

International Nuclear Information System (INIS)

Suzuki, Hiroshi; Miura, Akihiko

1999-09-01

All evidences and chemical data suggest non-chemical heating mechanism raised the filling temperature of the bituminized product. But they indicate the filling temperature was higher than before at the incident. We estimated the physical heat mechanism in the extruder. It is well known that the viscous-heating occurs in mixing process in extruders. In order to confirm the behavior of the torque and temperature, some experiment using laboratory scale extruder were performed. The result of the experiment using laboratory scale extruder showed that the phenomena of salt enrichment and salt accumulation were observed and they raised mixture temperature at the decreased feed rate. These phenomena depend on the feed rate. It is considered that they have large contribution to heat transportation and operational torque due to the friction between screw and mixture. In this report, all experiment result are explained. (author)

Effects of extruded corn on milk yield and composition and blood parameters in lactating dairy cows

Directory of Open Access Journals (Sweden)

Igino Andrighetto

2010-01-01

Full Text Available According to a 2x2 cross over design, fourteen Holstein dairy cows at 99±55 DIM were fed two diets containing 21.5% DM of either ground corn (GC or extruded corn (EC. Performance and metabolic profile were detected during the third week of each experimental period. DMI and milk yield were not affected by dietary treatments. Milk fat and protein percentage of EC diet were significantly (P<0.10 lower than those of GC diet. Probably the higher rumen degradability of starch from EC thesis modified the synthesis of specific fatty acids leading to a milk fat depression event. Diets did not influence blood parameters, except for lower values of total protein and glucose content in EC diet-fed cows. Results suggested that the dietary inclusion of extruded corn should not be used at the tested level of substitution.

Effect of low-doses gamma radiation on physico-chemical properties of cereal starches

International Nuclear Information System (INIS)

Gambus, H.; Juszczak, L.; Achremowicz, B.

1995-01-01

Wheat starch of Emika variety was treated with 3 and 5 kGy doses of gamma radiation, rye starch of Dankowskie Zlote variety and triticale starch of Dagro variety - with 3 kGy doses. Radiation of this starch caused an increase of reduction ability and water solubility at 60 and 80 o C. However with the increased radiation doses a significant decrease of maximum viscosity and of the viscosity of starch pastes being cooled to 50% was observed. Mild radiopolimerization also decreased the degree of retrogradation of wheat and rye starch pastes stored at above 0 o C. (author)

Physiochemical properties and kinetics of glucoamylase produced from deoxy-d-glucose resistant mutant of Aspergillus niger for soluble starch hydrolysis.

Science.gov (United States)

Riaz, Muhammad; Rashid, Muhammad Hamid; Sawyer, Lindsay; Akhtar, Saeed; Javed, Muhammad Rizwan; Nadeem, Habibullah; Wear, Martin

2012-01-01

Glucoamylases (GAs) from a wild and a deoxy-d-glucose-resistant mutant of a locally isolated Aspergillus niger were purified to apparent homogeneity. The subunit molecular mass estimated by SDS-PAGE was 93 kDa for both strains, while the molecular masses determined by MALDI-TOF for wild and mutant GAs were 72.876 and 72.063 kDa, respectively. The monomeric nature of the enzymes was confirmed through activity staining. Significant improvement was observed in the kinetic properties of the mutant GA relative to the wild type enzyme. Kinetic constants of starch hydrolysis for A. niger parent and mutant GAs calculated on the basis of molecular masses determined through MALDI-TOF were as follows: k cat = 343 and 727 s -1 , K m = 0.25 and 0.16 mg mL -1 , k cat / K m (specificity constant) = 1374 and 4510 mg mL -1 s -1 , respectively. Thermodynamic parameters for soluble starch hydrolysis also suggested that mutant GA was more efficient compared to the parent enzyme.

Utilisation of sago starch for wound dressing

International Nuclear Information System (INIS)

Kamaruddin Hashim; Khairul Zaman Mohd Dahlan; Kamarudin Bahari

2000-01-01

Sago starch is utilized in Malaysia mainly for the purpose of food production. The purpose of the research is to diversify the use of sago starch for medical application particularly in development of hydrogel wound dressing. The sago starch is blending with water-soluble polymer such as polyvinyl pyrrolidone, polyvinyl alcohol and polyethylene oxide and irradiated with electron beam accelerator to form hydrogel. The parameters such gel strength, elasticity, swelling, gel fraction and tackiness have to be consider for this type of application. We also study the effect of adding additive such as carboxymethyl cellulose and polypropylene glycol into the system to enhance the property of sago starch hydrogel. Works on the use of chitosan in the blend have been performed, in order to prevent microbiological growth such as bacteria and fungi on the hydrogel. (author)

Extrusion of blends of cassava leaves and cassava flour: physical characteristics of extrudates

Directory of Open Access Journals (Sweden)

Cristiane da Cunha Salata

2014-09-01

Full Text Available A cassava-based puffed snack was produced using a single screw extruder to determine the effect of the raw material composition (cassava leaf flour and moisture and the process parameters (extrusion temperature and screw speed on the physical characteristics of an extruded-expanded snack. A central composite rotational design, including four factors with 30 treatments, was used with the following as dependent variables: expansion index, specific volume, water solubility index, water absorption index, color (L*, a*, b*, and hardness. Under conditions of low moisture content (12 to 14%, low percentage of cassava leaf flour (2 to 4%, and intermediate conditions of extrusion temperature (100°C and screw speed (230rpm, it was possible to obtain puffed snack products with desirable characteristics.

Determination of the starch-phosphorylating enzyme activity in plant extracts

DEFF Research Database (Denmark)

Ritte, G.; Steup, M.; Kossmann, J.

2003-01-01

For quantification of alpha-glucan, water dikinase(GWD) activity in crude extracts of plant tissues a radio-labeling assay was established that uses soluble starch and P-33-labeled ATP as phosphate acceptor and donor, respectively. A constant rate of starch labeling was observed only if the ATP...... incorporation of phosphate whereas extracts from potato (Solanum tuberosum L.) tuber expressing a GWD antisense construct exhibited less activity than the wild-type control. To our knowledge this is the first time that a quantification of the starch-phosphorylating activity has been achieved in plant crude...

Recreating the synthesis of starch granules in yeast

Science.gov (United States)

Pfister, Barbara; Sánchez-Ferrer, Antoni; Diaz, Ana; Lu, Kuanjen; Otto, Caroline; Holler, Mirko; Shaik, Farooque Razvi; Meier, Florence; Mezzenga, Raffaele; Zeeman, Samuel C

2016-01-01

Starch, as the major nutritional component of our staple crops and a feedstock for industry, is a vital plant product. It is composed of glucose polymers that form massive semi-crystalline granules. Its precise structure and composition determine its functionality and thus applications; however, there is no versatile model system allowing the relationships between the biosynthetic apparatus, glucan structure and properties to be explored. Here, we expressed the core Arabidopsis starch-biosynthesis pathway in Saccharomyces cerevisiae purged of its endogenous glycogen-metabolic enzymes. Systematic variation of the set of biosynthetic enzymes illustrated how each affects glucan structure and solubility. Expression of the complete set resulted in dense, insoluble granules with a starch-like semi-crystalline organization, demonstrating that this system indeed simulates starch biosynthesis. Thus, the yeast system has the potential to accelerate starch research and help create a holistic understanding of starch granule biosynthesis, providing a basis for the targeted biotechnological improvement of crops. DOI: http://dx.doi.org/10.7554/eLife.15552.001 PMID:27871361

Investigation of functional properties and color changes of corn extrudates enriched with broccoli or olive paste.

Science.gov (United States)

Bisharat, Ghassan I; Katsavou, Ioanna D; Panagiotou, Nikolaos M; Krokida, Magdalini K; Maroulis, Zacharias B

2015-12-01

Following the tendency of replacing common food snacks with healthier food products, extruded snacks with corn flour and broccoli (4-10%) or olive paste (4-8%) were investigated in this study. The effect of material characteristics, including feed moisture content (14-19%), and broccoli or olive paste concentration, and extrusion conditions, including screw speed (150-250 r/min), and extrusion temperature (140-180 ℃), on the functional properties (water absorption index, water solubility index, and oil absorption index), as well as color change (ΔE) of the extruded snacks was studied. Regression analysis showed that screw speed did not significantly influence (p > 0.05) the properties. After mathematical modelling it was found that broccoli and olive paste concentration, as well as temperature increment, caused a decrease in water absorption index (minimum of 5.6 and 6.4 g/g sample, respectively) and an increase in water solubility index (maximum of 18.7 and 10.9 g/100 g sample, respectively), while feed moisture presented opposite tendency. Higher extrusion temperature led to an increment of oil absorption index (approximately to 1.2 and 1 mL/g sample) and decrement of color changes. Finally, feed moisture and broccoli concentration lowered oil absorption index and color of corn/broccoli extrudates, while olive paste concentration caused their increment. © The Author(s) 2014.

Effects of single and dual physical modifications on pinhão starch.

Science.gov (United States)

Pinto, Vânia Zanella; Vanier, Nathan Levien; Deon, Vinicius Gonçalves; Moomand, Khalid; El Halal, Shanise Lisie Mello; Zavareze, Elessandra da Rosa; Lim, Loong-Tak; Dias, Alvaro Renato Guerra

2015-11-15

Pinhão starch was modified by annealing (ANN), heat-moisture (HMT) or sonication (SNT) treatments. The starch was also modified by a combination of these treatments (ANN-HMT, ANN-SNT, HMT-ANN, HMT-SNT, SNT-ANN, SNT-HMT). Whole starch and debranched starch fractions were analyzed by gel-permeation chromatography. Moreover, crystallinity, morphology, swelling power, solubility, pasting and gelatinization characteristics were evaluated. Native and single ANN and SNT-treated starches exhibited a CA-type crystalline structure while other modified starches showed an A-type structure. The relative crystallinity increased in ANN-treated starches and decreased in single HMT- and SNT-treated starches. The ANN, HMT and SNT did not provide visible cracks, notches or grooves to pinhão starch granule. SNT applied as second treatment was able to increase the peak viscosity of single ANN- and HMT-treated starches. HMT used alone or in dual modifications promoted the strongest effect on gelatinization temperatures and enthalpy. Copyright © 2015 Elsevier Ltd. All rights reserved.

Physicochemical Characteristics of Artificial Rice from Composite Flour: Modified Cassava Starch, Canavalia ensiformis and Dioscorea esculenta

Science.gov (United States)

Sumardiono, Siswo; Pudjihastuti, Isti; Handayani, Noer Abyor; Kusumayanti, Heny

2018-02-01

Indonesia is the third largest country on the global paddy rice production and also considered as a rice importer. Even, Indonesia has the biggest per capita consumption of paddy rice (140 kg of paddy rice per person per year). Product diversification using local commodities. Artificial rice is potential to be developed as a new value product using different types of grains. It is one of appropriate solutions for reducing imported rice rate. Artificial rice was produced using high nutrition composite flours (modified cassava starch, corn, Canavalian ensiformis, and Dioscorea esculenta). This study consists of three main stages, preparation of composite flour, formulation, and artificial rice production using hot extruder capacity 10 kg/day. The objectives of this studies were to investigate some formulation in compare with commercial paddy rice. Artificial rice has been successfully conducted using prototype of hot extruder with the temperature 95°C. Physical analyses (color and water absorption) were carried out to artificial rice product and commercial paddy rice. Chemical analyses (nutrition and amylose content) of product will be also presented in this study. The best formulation of artificial rice was achieved in 80% modified cassava starch, 10% Canavalian ensiformis, and 10% Dioscorea esculenta, respectively.

Starch and fibre intake and glucose postprandial response of dogs

Directory of Open Access Journals (Sweden)

Mariana Monti

2016-02-01

Full Text Available ABSTRACT: Fibre has been studied to reduce the postprandial glucose response of dogs, but the results are inconsistent. Starch intake, however, was not properly considered in the published studies. The effects of starch and fibre intake on the postprandial glucose response were studied in non-obese adult dogs. Cellulose (CEL, carboxymethylcellulose (CMC, pea fibre (PE and sugarcane fibre (SCF were combined to form six diets with starch contents ranging from 33% to 42%: SCF+CEL and PE+CEL diets, both with high insoluble fibre (IF=22% and low soluble fibre (SF=2.5% content; SCF+CMC and PE+CMC diets with high SF (SF=4.5%; IF=19% content; and CMC and CEL diets with low dietary fibre (14% content. The diets were fed in two amounts, providing an intake of 9.5g or 12.5g of starch (kg0.75-1 day-1, totaling 12 treatments. Each diet was fed to six dogs conditioned to consume all of the daily food in 10min. Their plasma glucose levels were measured before and during 480min after food intake. Results of fibre and starch intake and their interactions were compared by repeated measures ANOVA and the Tukey test (P0.05. High-dose starch intake, however, induced a higher glycaemia at 180 and 240min after the meal and a greater maximal glycaemia and greater area under the glucose curve (P<0.05. A range in insoluble and soluble fibre intake does not change postprandial glucose response, and the amount of starch intake is a main factor for the postprandial glucose response of healthy non-obese dogs.

Monitoring of soluble starch hydrolysis induced by α-amylase from Aspergillus oryzae using ultrasonic spectroscopy

Science.gov (United States)

Sierra, Carlos; Resa, Pablo; Buckin, Vitaly; Elvira, Luis

2012-05-01

The online monitoring of enzymatic starch hydrolysis is an important issue for several industrial sectors, mainly in the alimentary industry. Ultrasonic non-invasive methods based on the detection of wave velocity and amplitude changes can be used to study this enzymatic reaction. These wave propagating changes are result of physicalchemical modifications produced in the media by the starch hydrolysis. In this work the starch hydrolysis induced by the enzyme α-amylase from Aspergillus oryzae is studied. This biochemical reaction has been monitored using a high-resolution ultrasonic spectroscopy (HR-US) which is non-invasive and nondestructive. The measured time profiles o of ultrasonic velocity are explained in terms of the starch hydrolysis and the subsequent production of oligosaccharides as a consequence of the enzymatic action. The obtained results have been compared to a conventional off-line technique used in biochemistry, the iodine-starch reaction, a spectrophotometric method to quantify the amount of starch remaining in the medium. The combination of these two types of measurement provides more complete information about the biochemical processes occurred during hydrolysis.

Preparation and Characterization of Starch Nanoparticles for Controlled Release of Curcumin

Directory of Open Access Journals (Sweden)

Suk Fun Chin

2014-01-01

Full Text Available Curcumin was loaded onto starch nanoparticles by using in situ nanoprecipitation method and water-in-oil microemulsion system. Curcumin loaded starch nanoparticles exhibited enhanced solubility in aqueous solution as compared to free curcumin. Effects of formulation parameters such as types of reaction medium, types of surfactant, surfactant concentrations, oil/ethanol ratios, loading time, and initial curcumin concentration were found to affect the particle size and loading efficiency (LF of the curcumin loaded starch nanoparticles. Under optimum conditions, curcumin loaded starch nanoparticles with mean particles size of 87 nm and maximum loading efficiency of 78% were achieved. Curcumin was observed to release out from starch nanoparticles in a sustained way under physiological pH over a period of 10 days.

Modification of foxtail millet starch by combining physical, chemical and enzymatic methods.

Science.gov (United States)

Dey, Ashim; Sit, Nandan

2017-02-01

Modification of foxtail millet starch was carried out by heat moisture treatment (HT), acid hydrolysis (AH), enzymatic treatment (EH), Ultrasound treatment (UT) and their combinations. A total of 15 modified starches were prepared by combining the various methods and properties were compared with native starch. The solubilities of the starches modified by HT were found to decrease whereas for other single modifications it increased. It also increased with number of modifications applied. The swelling power decreased for all the modified starches and a decrease in swelling power was observed with increase in number of modifications. Freeze-thaw stability improved for starches modified by single physical modifications i.e. HT and UT. Decrease in viscosities was observed for the modified starches and was particularly affected by AH. The pasting temperature was found to increase for those modified starches where HT was carried out. The modified starches gave softer gels. Copyright © 2016 Elsevier B.V. All rights reserved.

Mass production of C50 carotenoids by Haloferax mediterranei in using extruded rice bran and starch under optimal conductivity of brined medium.

Science.gov (United States)

Chen, C Will; Hsu, Shu-hui; Lin, Ming-Tse; Hsu, Yi-hui

2015-12-01

Microbial carotenoids have potentially healthcare or medical applications. Haloferax mediterranei was difficult to economically grow into a large quantities as well as producing a valuable pigment of carotenoids. This study reports a novel investigation into the optimal conductivity on the mass production of carotenoids from H. mediterranei. The major component at about 52.4% in the extracted red pigment has been confirmed as bacterioruberin, a C50 carotenoids, by liquid chromatography separation and mass spectrometry analysis. By maintaining higher conductivity of 40 S/m in the brined medium, the cell concentration attained to 7.73 × 10(9) cells/L with low pigments concentration of 125 mg/L. When the conductivity was controlled at about 30 S/m, we obtained the highest cell concentration to 1.29 × 10(10) cells/L with pigments of 361.4 mg/L. When the conductivity was maintained at optimal 25 S/m, the pigments can be increased to maximum value of 555.6 mg/L at lower cell concentration of 9.22 × 10(9) cells/L. But conductivity below 20 S/m will cause the significant decrease in cell concentration as well as pigments due to the osmotic stress around the cells. Red pigment of carotenoids from an extremely halophilic archaebacterium could be efficiently produced to a high concentration by applying optimal conductivity control in the brined medium with extruded low-cost rice bran and corn starch.

Effect of carboxymethyl cellulose concentration on physical properties of biodegradable cassava starch-based films

Directory of Open Access Journals (Sweden)

Sriburi Pensiri

2011-02-01

Full Text Available Abstract Background Cassava starch, the economically important agricultural commodity in Thailand, can readily be cast into films. However, the cassava starch film is brittle and weak, leading to inadequate mechanical properties. The properties of starch film can be improved by adding plasticizers and blending with the other biopolymers. Results Cassava starch (5%w/v based films plasticized with glycerol (30 g/100 g starch were characterized with respect to the effect of carboxymethyl cellulose (CMC concentrations (0, 10, 20, 30 and 40%w/w total solid and relative humidity (34 and 54%RH on the mechanical properties of the films. Additionally, intermolecular interactions were determined by Fourier transform infrared spectroscopy (FT-IR, melting temperature by differential scanning calorimetry (DSC, and morphology by scanning electron microscopy (SEM. Water solubility of the films was also determined. Increasing concentration of CMC increased tensile strength, reduced elongation at break, and decreased water solubility of the blended films. FT-IR spectra indicated intermolecular interactions between cassava starch and CMC in blended films by shifting of carboxyl (C = O and OH groups. DSC thermograms and SEM micrographs confirmed homogeneity of cassava starch-CMC films. Conclusion The addition of CMC to the cassava starch films increased tensile strength and reduced elongation at break of the blended films. This was ascribed to the good interaction between cassava starch and CMC. Cassava starch-CMC composite films have the potential to replace conventional packaging, and the films developed in this work are suggested to be suitable for low moisture food and pharmaceutical products.

Mobilization and Role of Starch, Protein, and Fat Reserves during Seed Germination of Six Wild Grassland Species.

Science.gov (United States)

Zhao, Ming; Zhang, Hongxiang; Yan, Hong; Qiu, Lu; Baskin, Carol C

2018-01-01

Since seed reserves can influence seed germination, the quantitative and qualitative differences in seed reserves may relate to the germination characteristics of species. The purpose of our study was to evaluate the correlation between germination and seed reserves, as well as their mobilization during germination of six grassland species ( Chloris virgata , Kochia scoparia , Lespedeza hedysaroides , Astragalus adsurgens , Leonurus artemisia , and Dracocephalum moldavica ) and compare the results with domesticated species. We measured starch, protein, and fat content in dry seeds and the initial absorption of water during imbibition. Starch, soluble protein, fat, and soluble sugar content also were determined at five stages during germination. Starch, protein, and fat reserves in dry seeds were not significantly correlated with germination percentage and rate (speed), but soluble sugar and soluble protein contents at different germination stages were positively significantly correlated with germination rate for the six species. Starch was mainly used during seed imbibition, and soluble protein was used from the imbibition stage to the highest germination stage. Fat content for all species remained relatively constant throughout germination for six species, regardless of the proportion of other seed reserves in the seeds. Our results for fat utilization differ from those obtained for cultivated grasses and legumes. These results provide new insight on the role of seed reserves as energy resources in germination for wild species.

Mobilization and Role of Starch, Protein, and Fat Reserves during Seed Germination of Six Wild Grassland Species

Directory of Open Access Journals (Sweden)

Ming Zhao

2018-02-01

Full Text Available Since seed reserves can influence seed germination, the quantitative and qualitative differences in seed reserves may relate to the germination characteristics of species. The purpose of our study was to evaluate the correlation between germination and seed reserves, as well as their mobilization during germination of six grassland species (Chloris virgata, Kochia scoparia, Lespedeza hedysaroides, Astragalus adsurgens, Leonurus artemisia, and Dracocephalum moldavica and compare the results with domesticated species. We measured starch, protein, and fat content in dry seeds and the initial absorption of water during imbibition. Starch, soluble protein, fat, and soluble sugar content also were determined at five stages during germination. Starch, protein, and fat reserves in dry seeds were not significantly correlated with germination percentage and rate (speed, but soluble sugar and soluble protein contents at different germination stages were positively significantly correlated with germination rate for the six species. Starch was mainly used during seed imbibition, and soluble protein was used from the imbibition stage to the highest germination stage. Fat content for all species remained relatively constant throughout germination for six species, regardless of the proportion of other seed reserves in the seeds. Our results for fat utilization differ from those obtained for cultivated grasses and legumes. These results provide new insight on the role of seed reserves as energy resources in germination for wild species.

Application of carrier and plasticizer to improve the dissolution and bioavailability of poorly water-soluble baicalein by hot melt extrusion.

Science.gov (United States)

Zhang, Yilan; Luo, Rui; Chen, Yi; Ke, Xue; Hu, Danrong; Han, Miaomiao

2014-06-01

The objective of this study was to develop a suitable formulation for baicalein (a poorly water-soluble drug exhibiting high melting point) to prepare solid dispersions using hot melt extrusion (HME). Proper carriers and plasticizers were selected by calculating the Hansen solubility parameters, evaluating melting processing condition, and measuring the solubility of obtained melts. The characteristic of solid dispersions prepared by HME was evaluated. The dissolution performance of the extrudates was compared to the pure drug and the physical mixtures. Physicochemical properties of the extrudates were characterized by differential scanning calorimetry (DSC), powder X-ray diffraction (PXRD), and Fourier transform infrared spectroscopy (FTIR). Relative bioavailability after oral administration in beagle dogs was assessed. As a result, Kollidon VA64 and Eudragit EPO were selected as two carriers; Cremophor RH was used as the plasticizer. The dissolution of all the extrudates was significantly improved. DSC and PXRD results suggested that baicalein in the extrudates was amorphous. FTIR spectroscopy revealed the interaction between drug and polymers. After oral administration, the relative bioavailability of solid dispersions with VA64 and EPO was comparative, about 2.4- and 2.9-fold greater compared to the pure drug, respectively.

Modification of wheat starch with succinic acid/acetic anhydride and azelaic acid/acetic anhydride mixtures I. Thermophysical and pasting properties.

Science.gov (United States)

Subarić, Drago; Ačkar, Durđica; Babić, Jurislav; Sakač, Nikola; Jozinović, Antun

2014-10-01

The aim of this research was to investigate the influence of modification with succinic acid/acetic anhydride and azelaic acid/acetic anhydride mixtures on thermophysical and pasting properties of wheat starch. Starch was isolated from two wheat varieties and modified with mixtures of succinic acid and acetic anhydride, and azelaic acid and acetic anhydride in 4, 6 and 8 % (w/w). Thermophysical, pasting properties, swelling power, solubility and amylose content of modified starches were determined. The results showed that modifications with mixtures of afore mentioned dicarboxylic acids with acetic anhydride decreased gelatinisation and pasting temperatures. Gelatinisation enthalpy of Golubica starch increased, while of Srpanjka starch decreased by modifications. Retrogradation after 7 and 14 day-storage at 4 °C decreased after modifications of both starches. Maximum, hot and cold paste viscosity of both starches increased, while stability during shearing at high temperatures decreased. % setback of starches modified with azelaic acid/acetic anhydride mixture decreased. Swelling power and solubility of both starches increased by both modifications.

Enrichment of rice-based extrudates with Cactus Opuntia dillenii seed powder: a novel source of fiber and antioxidants.

Science.gov (United States)

Rayan, Ahmed M; Morsy, Noha E; Youssef, Khaled M

2018-02-01

The present study investigated the effects of adding the powder of cactus Opuntia dillenii ( O. dillenii ) seeds on the functional properties, fiber, antioxidants and acceptability of rice-based extrudates. The control blend consisting basically of rice flour was replaced with O. dillenii seed powder at 2, 4, 6, 8, 10, 15 and 20% then extruded at the optimum processing conditions. The extruded products were evaluated for their chemical composition, functional properties, color attributes, antioxidant activity and sensory characteristics. The results revealed that adding O. dillenii seeds powder enhanced the fiber, phenolics, flavonoid contents and antioxidant activity of extrudates. Expansion, bulk density and breaking strength were significantly decreased, while water absorption index, water solubility index and oil absorption index were significantly increased compared to the control. Furthermore, the mean scores of sensory evaluation indicated clear improvements in all tested sensory attributes, which significantly increased by increasing the level of O. dillenii seed powder up to 15%. The results confirmed that O. dillenii seed powder could be incorporated in rice to develop snack products of acceptable functional, nutritional and sensory properties.

Effects of citric acid esterification on digestibility, structural and physicochemical properties of cassava starch.

Science.gov (United States)

Mei, Ji-Qiang; Zhou, Da-Nian; Jin, Zheng-Yu; Xu, Xue-Ming; Chen, Han-Qing

2015-11-15

In this study, citric acid was used to react with cassava starch in order to compare the digestibility, structural and physicochemical properties of citrate starch samples. The results indicated that citric acid esterification treatment significantly increased the content of resistant starch (RS) in starch samples. The swelling power and solubility of citrate starch samples were lower than those of native starch. Compared with native starch, a new peak at 1724 cm(-1) was appeared in all citrate starch samples, and crystalline peaks of all starch citrates became much smaller or even disappeared. Differential scanning calorimetry results indicated that the endothermic peak of citrate starches gradually shrank or even disappeared. Moreover, the citrate starch gels exhibited better freeze-thaw stability. These results suggested that citric acid esterification induced structural changes in cassava starch significantly affected its digestibility and it could be a potential method for the preparation of RS with thermal stability. Copyright © 2015 Elsevier Ltd. All rights reserved.

Intelligent Extruder

Energy Technology Data Exchange (ETDEWEB)

AlperEker; Mark Giammattia; Paul Houpt; Aditya Kumar; Oscar Montero; Minesh Shah; Norberto Silvi; Timothy Cribbs

2003-04-24

''Intelligent Extruder'' described in this report is a software system and associated support services for monitoring and control of compounding extruders to improve material quality, reduce waste and energy use, with minimal addition of new sensors or changes to the factory floor system components. Emphasis is on process improvements to the mixing, melting and de-volatilization of base resins, fillers, pigments, fire retardants and other additives in the :finishing'' stage of high value added engineering polymer materials. While GE Plastics materials were used for experimental studies throughout the program, the concepts and principles are broadly applicable to other manufacturers materials. The project involved a joint collaboration among GE Global Research, GE Industrial Systems and Coperion Werner & Pleiderer, USA, a major manufacturer of compounding equipment. Scope of the program included development of a algorithms for monitoring process material viscosity without rheological sensors or generating waste streams, a novel detection scheme for rapid detection of process upsets and an adaptive feedback control system to compensate for process upsets where at line adjustments are feasible. Software algorithms were implemented and tested on a laboratory scale extruder (50 lb/hr) at GE Global Research and data from a production scale system (2000 lb/hr) at GE Plastics was used to validate the monitoring and detection software. Although not evaluated experimentally, a new concept for extruder process monitoring through estimation of high frequency drive torque without strain gauges is developed and demonstrated in simulation. A plan to commercialize the software system is outlined, but commercialization has not been completed.

Effects of amino acids on the physiochemical properties of potato starch.

Science.gov (United States)

Cui, Min; Fang, Ling; Zhou, Hongxian; Yang, Hong

2014-05-15

The objective of this study was to evaluate effects of different amino acid additives (phenylalanine (Phe), methionine (Met), lysine (Lys), arginine (Arg), aspartic acid (Asp) and glutamic acid (Glu)) on the physicochemical properties of potato starch gels. Charge-carrying amino acids (Lys, Arg, Asp and Glu) significantly decreased the swelling power, solubility, light transmittance, L(∗) value and gel strength of potato starch, but increased syneresis during freeze-thaw treatment, while neutral amino acids (Phe and Met) did not cause modifications in starch gels. During heating, potato starch with fortified charge-carrying amino acids showed a lower peak G' (storage modulus), when compared with Phe and Met. Results showed that charge-carrying amino acids could modify physicochemical properties and improve the nutritional values of starch-based products. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of forage type and extruded linseed supplementation on methane production and milk fatty acid composition of lactating dairy cows.

Science.gov (United States)

Livingstone, K M; Humphries, D J; Kirton, P; Kliem, K E; Givens, D I; Reynolds, C K

2015-06-01

Replacing dietary grass silage (GS) with maize silage (MS) and dietary fat supplements may reduce milk concentration of specific saturated fatty acids (SFA) and can reduce methane production by dairy cows. The present study investigated the effect of feeding an extruded linseed supplement on milk fatty acid (FA) composition and methane production of lactating dairy cows, and whether basal forage type, in diets formulated for similar neutral detergent fiber and starch, altered the response to the extruded linseed supplement. Four mid-lactation Holstein-Friesian cows were fed diets as total mixed rations, containing either high proportions of MS or GS, both with or without extruded linseed supplement, in a 4×4 Latin square design experiment with 28-d periods. Diets contained 500 g of forage/kg of dry matter (DM) containing MS and GS in proportions (DM basis) of either 75:25 or 25:75 for high MS or high GS diets, respectively. Extruded linseed supplement (275 g/kg ether extract, DM basis) was included in treatment diets at 50 g/kg of DM. Milk yields, DM intake, milk composition, and methane production were measured at the end of each experimental period when cows were housed in respiration chambers. Whereas DM intake was higher for the MS-based diet, forage type and extruded linseed had no significant effect on milk yield, milk fat, protein, or lactose concentration, methane production, or methane per kilogram of DM intake or milk yield. Total milk fat SFA concentrations were lower with MS compared with GS-based diets (65.4 vs. 68.4 g/100 g of FA, respectively) and with extruded linseed compared with no extruded linseed (65.2 vs. 68.6 g/100 g of FA, respectively), and these effects were additive. Concentrations of total trans FA were higher with MS compared with GS-based diets (7.0 vs. 5.4 g/100 g of FA, respectively) and when extruded linseed was fed (6.8 vs. 5. 6g/100 g of FA, respectively). Total n-3 FA were higher when extruded linseed was fed compared with no

Cassava and turmeric flour blends as new raw materials to extruded snacks

Directory of Open Access Journals (Sweden)

Alessandra Mussato Spinello

2014-02-01

Full Text Available Short cooking time and ability to blend varieties of food ingredients have made extrusion cooking a medium for low-cost and nutritionally improved food products. The effect of moisture, extrusion temperature and amount of turmeric flour mixed with cassava flour on physical characteristic of puffed snacks was evaluated in this work. Extrusion process was carried out using a single-screw extruder in a factorial central composite design with four factors. Results showed effect of extrusion parameters on dependents variables. High expansion, low browning, low water solubility index, intermediate water absorption index and high crispness desirable characteristics to puffed snacks are obtained in conditions of 12% moisture, 5% turmeric flour, 105º C of temperature and 250 rpm of screw speed. These paper point to the potential still unexplored of the use of flours of cassava and turmeric as raw materials in the development of extruded puffed snacks.

Use of enzymes to minimize the rheological dough problems caused by high levels of damaged starch in starch-gluten systems.

Science.gov (United States)

Barrera, Gabriela N; León, Alberto E; Ribotta, Pablo D

2016-05-01

During wheat milling, starch granules can experience mechanical damage, producing damaged starch. High levels of damaged starch modify the physicochemical properties of wheat flour, negatively affecting the dough behavior as well as the flour quality and cookie and bread making quality. The aim of this work was to evaluate the effect of α-amylase, maltogenic amylase and amyloglucosidase on dough rheology in order to propose alternatives to reduce the issues related to high levels of damaged starch. The dough with a high level of damaged starch became more viscous and resistant to deformations as well as less elastic and extensible. The soluble fraction of the doughs influenced the rheological behavior of the systems. The α-amylase and amyloglucosidase reduced the negative effects of high damaged starch contents, improving the dough rheological properties modified by damaged starch. The rheological behavior of dough with the higher damaged-starch content was related to a more open gluten network arrangement as a result of the large size of the swollen damaged starch granules. We can conclude that the dough rheological properties of systems with high damaged starch content changed positively as a result of enzyme action, particularly α-amylase and amyloglucosidase additions, allowing the use of these amylases and mixtures of them as corrective additives. Little information was reported about amyloglucosidase activity alone or combined with α-amylase. The combinations of these two enzymes are promising to minimize the negative effects caused by high levels of damaged starch on product quality. More research needs to be done on bread quality combining these two enzymes. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Combination process method of lactic acid hydrolysis and hydrogen peroxide oxidation for cassava starch modification

Science.gov (United States)

Sumardiono, Siswo; Pudjihastuti, Isti; Budiyono, Hartanto, Hansen; Sophiana, Intan Clarissa

2017-05-01

Indonesia is one of the world's largest wheat importer, some research are conducted to find other carbohydrate sources which can replace wheat. Cassava is very easy to find and grown in tropical climates especially Indonesia. The research is focused on cassava starch modification as a substitute for wheat flour in order to reduce consumption of wheat flour. The aim of this research is to assess the effect of temperature, pH, and the concentration of H2O2 in modifying cassava starch which. The combination methods are lactic acid hydroxylation and hydrogen peroxide oxidation to improve baking expansion. The carboxyl group, carbonyl group, swelling power, starch solubility, and baking expansion of starch are analized and calculated. Results showed that the modified cassava starch can substitute wheat flour with optimum conditions process at a concentration of H2O2 is 1.5% w/w, oxidation temperature is 50°C, and pH is 3 by the value of swelling power is 6.82%, solubility is 0.02%, and baking expansion is 7.2 cm3/gram.

A Comparative Study of Some Properties of Cassava and Tree Cassava Starch Films

Science.gov (United States)

Belibi, P. C.; Daou, T. J.; Ndjaka, J. M. B.; Nsom, B.; Michelin, L.; Durand, B.

Cassava and tree cassava starch films plasticized with glycerol were produced by casting method. Different glycerol contents (30, 35, 40 and 45 wt. % on starch dry basis) were used and the resulting films were fully characterized. Their water barrier and mechanical properties were compared. While increasing glycerol concentration, moisture content, water solubility, water vapour permeability, tensile strength, percent elongation at break and Young's modulus decreased for both cassava and tree cassava films. Tree cassava films presented better values of water vapour permeability, water solubility and percent elongation at break compared to those of cassava films, regardless of the glycerol content.

UTILIZATION OF CORN STARCH AS SUBSTRATE FOR Я

African Journals Online (AJOL)

IITA

substrate, 10.1 X102 CFU/ml soluble starch and nutrient broth medium ... enzymatic activity with corresponding maltose yield of 46.4mg/ml and 68.0mg/ml .... stand for 15min at room temperature, the ... order to inactivated the beta amylase.

Chemical, morphological and functional properties of Brazilian jackfruit (Artocarpus heterophyllus L.) seeds starch.

Science.gov (United States)

Madruga, Marta Suely; de Albuquerque, Fabíola Samara Medeiros; Silva, Izis Rafaela Alves; do Amaral, Deborah Silva; Magnani, Marciane; Queiroga Neto, Vicente

2014-01-15

Starches used in food industry are extracted from roots, tubers and cereals. Seeds of jackfruit are abundant and contain high amounts of starch. They are discarded during the fruit processing or consumption and can be an alternative source of starch. The starch was extract from the jackfruit seeds and characterised to chemical, morphological and functional properties. Soft and hard jackfruit seeds showed starch content of 92.8% and 94.5%, respectively. Starch granules showed round and bell shape and some irregular cuts on their surface with type-A crystallinity pattern, similar to cereals starches. The swelling power and solubility of jackfruit starch increased with increasing temperature, showing opaque pastes. The soft seeds starch showed initial and final gelatinisation temperature of 36°C and 56°C, respectively; while hard seeds starch presented initial gelatinisation at 40°C and final at 61°C. These results suggest that the Brazilian jackfruit seeds starches could be used in food products. Copyright © 2013 Elsevier Ltd. All rights reserved.

Performance of high amylose starch-composited gelatin films influenced by gelatinization and concentration.

Science.gov (United States)

Wang, Wenhang; Wang, Kun; Xiao, Jingdong; Liu, Yaowei; Zhao, Yana; Liu, Anjun

2017-01-01

In order to study the impact of starch in film performance, high amylose corn starch was composited in gelatin films under different gelatinization conditions and, in high and low concentrations (10 and 50wt.%). It was found that hot water gelatinized starch (Gel-Shw) increased film mechanical strength and was dependent upon the starch concentration. The addition of an alkali component to the starch significantly enhanced the swelling of the starch granules and expedited the gelatinization process. Incorporation of starch, especially the alkalized starch (Sha), into the gelatin films decreased film solubility which improved its water resistance and water vapor permeability (WVP). Multiple techniques (DSC, TGA, FT-IR, and XRD) were used to characterize the process and results, including the crosslinking of the dissolved starch molecules and the particles formed from gelatinized starch during retrogradation process, which played an important role in improving the thermal stability of the composited gelatin films. Overall, the starch-gelatin composition provides a potential approach to improve gelatin film performance and benefit its applications in the food industry. Copyright © 2016 Elsevier B.V. All rights reserved.

Mango kernel starch-gum composite films: Physical, mechanical and barrier properties.

Science.gov (United States)

Nawab, Anjum; Alam, Feroz; Haq, Muhammad Abdul; Lutfi, Zubala; Hasnain, Abid

2017-05-01

Composite films were developed by the casting method using mango kernel starch (MKS) and guar and xanthan gums. The concentration of both gums ranged from 0% to 30% (w/w of starch; db). Mechanical properties, oxygen permeability (OP), water vapor permeability (WVP), solubility in water and color parameters of composite films were evaluated. The crystallinity and homogeneity between the starch and gums were also evaluated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The scanning electron micrographs showed homogeneous matrix, with no signs of phase separation between the components. XRD analysis demonstrated diminished crystalline peak. Regardless of gum type the tensile strength (TS) of composite films increased with increasing gum concentration while reverse trend was noted for elongation at break (EAB) which found to be decreased with increasing gum concentration. The addition of both guar and xanthan gums increased solubility and WVP of the composite films. However, the OP was found to be lower than that of the control with both gums. Furthermore, addition of both gums led to changes in transparency and opacity of MKS films. Films containing 10% (w/w) xanthan gum showed lower values for solubility, WVP and OP, while film containing 20% guar gum showed good mechanical properties. Copyright © 2017 Elsevier B.V. All rights reserved.

Development and Optimization of a Wet Granulation Process at Elevated Temperature for a Poorly Compactible Drug Using Twin Screw Extruder for Continuous Manufacturing.

Science.gov (United States)

Meena, Anuprabha K; Desai, Divyakant; Serajuddin, Abu T M

2017-02-01

The objective of this study was to enhance tabletability of a poorly compactible drug, acetaminophen, by wet granulation using twin screw extruder at high temperature. It was desired that there would be minimum amounts of excipients used and the granules obtained after extrusion would be dry and fall within a size range suitable for tableting without any further processing. Mixtures of acetaminophen (95%) with binders (5% povidone or partially pregelatinized starch) were wet granulated through twin screw extruder at 70°C by adding 7% w/w water. The process had a short granulation time (processing temperature used, no drying after extrusion was needed. By optimizing formulation and processing parameters, >90% granules in the size range of 125 to 1000 μm (1.7 MPa, which was superior to that of tablets prepared by conventional high shear wet granulation. As the granules could be extruded continuously and did not require drying and milling, the method was amenable to continuous processing. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Optimization of barrel temperature and kidney bean flour percentage based on various physical properties of extruded snacks.

Science.gov (United States)

Agathian, G; Semwal, A D; Sharma, G K

2015-07-01

The aim of the experiment was to optimize barrel temperature (122 to 178 ± 0.5 °C) and red kidney bean flour percentage (KBF) (12 to 68 ± 0.5 %) based on physical properties of extrudates like flash off percentage, water absorption index (WAI), water solubility index (WSI), bulk density (BD), radial expansion ratio (RER) and overall acceptability (OAA) using single screw extruder. The study was carried out by central composite rotatable design (CCRD) using Response surface methodology (RSM) and moisture content of feed was kept as constant 16.0 ± 0.5 % throughout experiments. Mathematical models for various responses were found to fit significantly (P Extruded snack prepared with rice flour (80 %) and kidney bean flour (20 %) at optimized conditions was accepted by the taste panellists and above 20 % KB incorporation was found to decrease overall acceptability score.

The effect of acid hydrolysis on the technological functional properties of pinhão (Araucaria brasiliensis starch

Directory of Open Access Journals (Sweden)

Roberta Cruz Silveira Thys

2013-02-01

Full Text Available Technological functional properties of native and acid-thinned pinhão (seeds of Araucária angustifolia, Brazilian pine starches were evaluated and compared to those of native and acid-thinned corn starches. The starches were hydrolyzed (3.2 mol.L-1 HCl, 44 ºC, 6 hours and evaluated before and after the hydrolysis reaction in terms of formation, melting point and thermo-reversibility of gel starches, retrogradation (in a 30-day period and measurements every three days, paste freezing and thawing stability (after six freezing and thawing cycles, swelling power, and solubility. The results of light transmittance (% of pastes of native and acid-thinned pinhão starches was higher (lower tendency to retrogradation than that obtained for corn starches after similar storage period. Native pinhão starch (NPS presented lower syneresis than native corn starch (NCS when submitted to freeze-thaw cycles. The acid hydrolysis increased the syneresis of the two native varieties under storage at 5 ºC and after freezing and thawing cycles. The solubility of NPS was lower than that of native corn starch at 25, 50, and 70 ºC. However, for the acid-thinned pinhão starch (APS, this property was significantly higher (p < 0.05 when compared to that of acid-thinned corn starch (ACS. From the results obtained, it can be said that the acid treatment was efficient in producing a potential fat substitute from pinhão starch variety, but this ability must be further investigated.

Physicochemical Characteristics of Artificial Rice from Composite Flour: Modified Cassava Starch, Canavalia ensiformis and Dioscorea esculenta

Directory of Open Access Journals (Sweden)

Sumardiono Siswo

2018-01-01

Full Text Available Indonesia is the third largest country on the global paddy rice production and also considered as a rice importer. Even, Indonesia has the biggest per capita consumption of paddy rice (140 kg of paddy rice per person per year. Product diversification using local commodities. Artificial rice is potential to be developed as a new value product using different types of grains. It is one of appropriate solutions for reducing imported rice rate. Artificial rice was produced using high nutrition composite flours (modified cassava starch, corn, Canavalian ensiformis, and Dioscorea esculenta. This study consists of three main stages, preparation of composite flour, formulation, and artificial rice production using hot extruder capacity 10 kg/day. The objectives of this studies were to investigate some formulation in compare with commercial paddy rice. Artificial rice has been successfully conducted using prototype of hot extruder with the temperature 95°C. Physical analyses (color and water absorption were carried out to artificial rice product and commercial paddy rice. Chemical analyses (nutrition and amylose content of product will be also presented in this study. The best formulation of artificial rice was achieved in 80% modified cassava starch, 10% Canavalian ensiformis, and 10% Dioscorea esculenta, respectively.

Structure, morphology and functionality of acetylated and oxidised barley starches.

Science.gov (United States)

El Halal, Shanise Lisie Mello; Colussi, Rosana; Pinto, Vânia Zanella; Bartz, Josiane; Radunz, Marjana; Carreño, Neftali Lenin Villarreal; Dias, Alvaro Renato Guerra; Zavareze, Elessandra da Rosa

2015-02-01

Acetylation and oxidation are chemical modifications which alter the properties of starch. The degree of modification of acetylated and oxidized starches is dependent on the catalyst and active chlorine concentrations, respectively. The objective of this study was to evaluate the effect of acetylation and oxidation on the structural, morphological, physical-chemical, thermal and pasting properties of barley starch. Barley starches were acetylated at different catalyst levels (11%, 17%, and 23% of NaOH solution) and oxidized at different sodium hypochlorite concentrations (1.0%, 1.5%, and 2.0% of active chlorine). Fourier-transformed infrared spectroscopy (FTIR), X-ray diffractograms, thermal, morphological, and pasting properties, swelling power and solubility of starches were evaluated. The degree of substitution (DS) of the acetylated starches increased with the rise in catalyst concentration. The percentage of carbonyl (CO) and carboxyl (COOH) groups in oxidized starches also increased with the rise of active chlorine level. The presence of hydrophobic acetyl groups, carbonyl and carboxyl groups caused a partial disorganization and depolymerization of starch granules. The structural, morphological and functional changes in acetylated and oxidized starches varied according to reaction conditions. Acetylation makes barley starch more hydrophobic by the insertion of acetyl groups. Also the oxidation promotes low retrogradation and viscosity. All these characteristics are important for biodegradable film production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Classification of cassava starch films by physicochemical properties and water vapor permeability quantification by FTIR and PLS.

Science.gov (United States)

Henrique, C M; Teófilo, R F; Sabino, L; Ferreira, M M C; Cereda, M P

2007-05-01

Cassava starches are widely used in the production of biodegradable films, but their resistance to humidity migration is very low. In this work, commercial cassava starch films were studied and classified according to their physicochemical properties. A nondestructive method for water vapor permeability determination, which combines with infrared spectroscopy and multivariate calibration, is also presented. The following commercial cassava starches were studied: pregelatinized (amidomax 3550), carboxymethylated starch (CMA) of low and high viscosities, and esterified starches. To make the films, 2 different starch concentrations were evaluated, consisting of water suspensions with 3% and 5% starch. The filmogenic solutions were dried and characterized for their thickness, grammage, water vapor permeability, water activity, tensile strength (deformation force), water solubility, and puncture strength (deformation). The minimum thicknesses were 0.5 to 0.6 mm in pregelatinized starch films. The results were treated by means of the following chemometric methods: principal component analysis (PCA) and partial least squares (PLS) regression. PCA analysis on the physicochemical properties of the films showed that the differences in concentration of the dried material (3% and 5% starch) and also in the type of starch modification were mainly related to the following properties: permeability, solubility, and thickness. IR spectra collected in the region of 4000 to 600 cm(-1) were used to build a PLS model with good predictive power for water vapor permeability determination, with mean relative errors of 10.0% for cross-validation and 7.8% for the prediction set.

Enzyme-resistant dextrins from potato starch for potential application in the beverage industry.

Science.gov (United States)

Jochym, Kamila Kapusniak; Nebesny, Ewa

2017-09-15

The objective of this study was to produce soluble enzyme-resistant dextrins by microwave heating of potato starch acidified with small amounts of hydrochloric and citric acids and to characterize their properties. Twenty five samples were initially made and their solubility was determined. Three samples with the highest water solubility were selected for physico-chemical (dextrose equivalent, molecular weight distribution, pasting characteristics, retrogradation tendency), total dietary fiber (TDF) analysis, and stability tests. TDF content averaged 25%. Enzyme-resistant dextrins practically did not paste, even at 20% samples concentration, and were characterized by low retrogradation tendency. The stability of the samples, expressed as a percentage increase of initial and final reducing sugar content, at low pH and during heating at low pH averaged 10% and 15% of the initial value, respectively. The results indicate that microwave heating could be an effective and efficient method of producing highly-soluble, low-viscous, and enzyme-resistant potato starch dextrins. Copyright © 2017 Elsevier Ltd. All rights reserved.

Preparation and Evaluation of Alcohol-Alkaline-Treated Rice Starch ...

African Journals Online (AJOL)

lower in the presence of large particles (3.55 ± 0.56 min); high content of MRS ... Conclusion: MRS exhibits improved water solubility and swelling capacity compared with RS, and is ..... excipient: Modification of the permeability of starch by.

Starch accumulation in hulless barley during grain filling.

Science.gov (United States)

Zheng, Xu-Guang; Qi, Jun-Cang; Hui, Hong-Shan; Lin, Li-Hao; Wang, Feng

2017-12-01

Starch consists of two types of molecules: amylose and amylopectin. The objective of this study was increase understanding about mechanisms related to starch accumulation in hulless barley (Hordeum vulgare L.) grain by measuring temporal changes in (i) grain amylose and amylopectin content, (ii) starch synthase activity, and (iii) the relative expressions of key starch-related genes. The amylopectin/amylose ratio gradually declined in both Beiqing 6 and Kunlun 12. In both cultivars, the activities of adenosine diphosphate glucose pyrophosphorylase, soluble starch synthase (SSS), granule bound starch synthase (GBSS), and starch branching enzyme (SBE) increased steadily during grain filling, reaching their maximums 20-25 days after anthesis. The activities of SSS and SBE were greater in Ganken 5 than in either Beiqing 6 or Kunlun 12. The expression of GBSS I was greater in Beiqing 6 and Kunlun 12 than in Ganken 5. In contrast, the expression of SSS I, SSS II and SBE I was greater in Ganken 5 than in Beiqing 6 and Kunlun 12. The peak in GBSS I expression was later than that of SSS I, SSS II, SBE IIa and SBE IIb. The GBSS I transcript in Kunlun 12 was expressed on average 90 times more than the GBSS II transcript. The results suggest that SBE and SSS may control starch synthesis at the transcriptional level, whereas GBSS I may control starch synthesis at the post transcriptional level. GBSS I is mainly responsible for amylose synthesis whereas SSS I and SBE II are mainly responsible for amylopectin synthesis in amyloplasts.

Physico-chemical, morphological and pasting properties of starches extracted from water Chestnuts (Trapa natans from three Lakes of Kashmir, India

Directory of Open Access Journals (Sweden)

Adil Gani

2010-06-01

Full Text Available Studies on physicochemical, morphology and pasting properties of starches extracted from water chestnuts of three Lakes of Kashmir valley (Wular, Anchar and Dal Lakes were conducted to determine their application in different food products. The water chestnut starch from Dal Lake had more oval shaped granules than water chestnut starches from the Wular and the Anchar Lakes.The unique feature of the water chestnut starches were shape of starch granules which looked like horn(s protruding from the surface which did not appear in other starches already studied. Proximate analysis of water chestnut starches showed that average protein content were 0.4%, amylose 29.5 % and ash 0.007 on dry weight basis. Increase in water binding capacity, swelling power and solubility was found over a temperature range of 50-90ºC. Water chestnut starches showed an increase in syneresis during freeze thaw cycles and decline in paste clarity upon storage. Starch extracted from the water chestnuts of the Dal Lake showed higher water binding capacity, swelling, solubility, past clarity, freeze thaw stability, peak viscosity, final viscosity and lower protein content, amylose content, pasting temperature and gel firmness than starches extracted from water chestnuts of the Wular and the Anchar Lakes.

Preparation of Starch/Gelatin Blend Microparticles by a Water-in-Oil Emulsion Method for Controlled Release Drug Delivery.

Science.gov (United States)

Phromsopha, Theeraphol; Baimark, Yodthong

2014-01-01

Information on the preparation and properties of starch/gelatin blend microparticles with and without crosslinking for drug delivery is presented. The blend microparticles were prepared by the water-in-oil emulsion solvent diffusion method. Glutaraldehyde and methylene blue were used as the crosslinker and the water-soluble drug model, respectively. The blend microparticles were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and UV-Vis spectroscopy. The functional groups of the starch and gelatin blend matrices were determined from the FTIR spectra. Blend microparticles with a nearly spherical shape and internal porous structure were observed from SEM images. The average particle size of the gelatin microparticles depended on the crosslinker ratio but not on the starch/gelatin blend ratio. The in vitro drug release content significantly decreased as the crosslinker ratio increased and the starch blend ratio decreased. The results demonstrated that the starch/gelatin blend microparticles should be a useful controlled release delivery carrier for water-soluble drugs.

Physicochemical Properties of Flaxseed Fortified Extruded Bean Snack

Directory of Open Access Journals (Sweden)

Naveen Vadukapuram

2014-01-01

Full Text Available Milled flaxseed was incorporated (0–20% into a combination of bean-corn flours and extruded in a twin screw extruder using corn curl method. Physicochemical parameters such as water activity, color, expansion ratio, bulk density, lipid content, and peroxide values of extruded snack were analyzed. Scanning electron micrographs were taken. Peroxide values and propanal contents were measured over four months of storage. Rancidity scores of extruded snack were measured using a trained panel. As expected, omega-3 fatty acids and bulk density increased with increasing flaxseed fortification levels. Extrudates with more flaxseed had decreased lightness values and expansion ratios. However, only the 15 and 20% flaxseed containing extrudates had expansion ratios that were significantly (P≤0.05 different from the control. In general, no significant difference (P>0.05 in water activity values was observed in the flaxseed fortified extrudates, except in the navy-corn based extrudates. Peroxide values increased with increased flaxseed levels and over a storage period. However, propanal values did not change significantly in the 5–10% flaxseed fortified extrudates but increased in extrudates with higher levels of flaxseed. Rancidity scores were correlated with peroxide values and did not increase significantly during storage under nitrogen flushed conditions.

Physicochemical Properties of Flaxseed Fortified Extruded Bean Snack.

Science.gov (United States)

Vadukapuram, Naveen; Hall, Clifford; Tulbek, Mehmet; Niehaus, Mary

2014-01-01

Milled flaxseed was incorporated (0-20%) into a combination of bean-corn flours and extruded in a twin screw extruder using corn curl method. Physicochemical parameters such as water activity, color, expansion ratio, bulk density, lipid content, and peroxide values of extruded snack were analyzed. Scanning electron micrographs were taken. Peroxide values and propanal contents were measured over four months of storage. Rancidity scores of extruded snack were measured using a trained panel. As expected, omega-3 fatty acids and bulk density increased with increasing flaxseed fortification levels. Extrudates with more flaxseed had decreased lightness values and expansion ratios. However, only the 15 and 20% flaxseed containing extrudates had expansion ratios that were significantly (P ≤ 0.05) different from the control. In general, no significant difference (P > 0.05) in water activity values was observed in the flaxseed fortified extrudates, except in the navy-corn based extrudates. Peroxide values increased with increased flaxseed levels and over a storage period. However, propanal values did not change significantly in the 5-10% flaxseed fortified extrudates but increased in extrudates with higher levels of flaxseed. Rancidity scores were correlated with peroxide values and did not increase significantly during storage under nitrogen flushed conditions.

Effect of incorporating finger millet in wheat flour on mixolab behavior, chapatti quality and starch digestibility.

Science.gov (United States)

Sharma, Bharati; Gujral, Hardeep Singh; Solah, Vicky

2017-09-15

Wheat and finger millet flour (two cultivars) were blended in the ratio (3:1) to form a composite flour and its dough properties were studied on the mixolab. The chapatti making and digestibility behavior of the composite flour was also investigated. The wheat finger millet (WFM) flour blend displayed up to 30.7% higher total phenolic content (TPC), 38.2% higher total flavonoid content (TFC) and 75.4% higher antioxidant activity (AOA) than the wheat flour. Chapattis prepared from the composite blends exhibited lower retrogradation as evident by the mixolab retrogradation index, higher values of soluble starch and soluble amylose in stored chapatti. The slowly digestible starch (SDS) correlated positively (R=0.816, p<0.05) with TPC and water absorption correlated positively (R=0.995, p<0.05) with damage starch content. The chapattis made from the composite flour had higher SDS and resistant starch (RS) values demonstrating potential as a food with functional characteristics. Copyright © 2017 Elsevier Ltd. All rights reserved.

Iron Bioavailability from Ferric Pyrophosphate in Extruded Rice Cofortified with Zinc Sulfate Is Greater than When Cofortified with Zinc Oxide in a Human Stable Isotope Study.

Science.gov (United States)

Hackl, Laura; Zimmermann, Michael B; Zeder, Christophe; Parker, Megan; Johns, Paul W; Hurrell, Richard F; Moretti, Diego

2017-03-01

Background: Extruded rice grains are often cofortified with iron and zinc. However, it is uncertain if the addition of zinc to iron-fortified rice affects iron absorption and whether this is zinc-compound specific. Objective: We investigated whether zinc, added as zinc oxide (ZnO) or zinc sulfate (ZnSO 4 ), affects human iron absorption from extruded rice fortified with ferric pyrophosphate (FePP). Methods: In 19 iron-depleted Swiss women (plasma ferritin ≤16.5 μ/L) aged between 20 and 39 y with a normal body mass index (in kg/m 2 ; 18.7-24.8), we compared iron absorption from 4 meals containing fortified extruded rice with 4 mg Fe and 3 mg Zn. Three of the meals contained extruded rice labeled with FePP ( 57 FePP): 1 ) 1 meal without added zinc ( 57 FePP-Zn), 2 ) 1 cofortified with ZnO ( 57 FePP+ZnO), and 3 ) 1 cofortified with ZnSO 4 ( 57 FePP+ZnSO 4 ). The fourth meal contained extruded rice without iron or zinc, extrinsically labeled with ferrous sulfate ( 58 FeSO 4 ) added as a solution after cooking. All 4 meals contained citric acid. Iron bioavailability was measured by isotopic iron ratios in red blood cells. We also measured relative in vitro iron solubility from 57 FePP-Zn, 57 FePP+ZnO, and 57 FePP+ZnSO 4 expressed as a fraction of FeSO 4 solubility. Results: Geometric mean fractional iron absorption (95% CI) from 57 FePP+ZnSO 4 was 4.5% (3.4%, 5.8%) and differed from 57 FePP+ZnO (2.7%; 1.8%, 4.1%) ( P iron bioavailabilities compared with 58 FeSO 4 were 62%, 57%, and 38% from 57 FePP+ZnSO 4 , 57 FePP-Zn, and 57 FePP+ZnO, respectively. In vitro solubility from 57 FePP+ZnSO 4 differed from that of 57 FePP-Zn (14.3%; P iron-depleted women, iron absorption from FePP-fortified extruded rice cofortified with ZnSO 4 was 1.6-fold (95% CI: 1.4-, 1.9-fold) that of rice cofortified with ZnO. These findings suggest that ZnSO 4 may be the preferable zinc cofortificant for optimal iron bioavailability of iron-fortified extruded rice. This trial was registered at

Changes in properties of starch isolated from whole rice grains with brown, black, and red pericarp after storage at different temperatures.

Science.gov (United States)

Ziegler, Valmor; Ferreira, Cristiano Dietrich; Goebel, Jorge Tiago Schwanz; El Halal, Shanise Lisie Mello; Santetti, Gabriela Soster; Gutkoski, Luiz Carlos; Zavareze, Elessandra da Rosa; Elias, Moacir Cardoso

2017-02-01

The aim of this study was to evaluate the physicochemical, morphological, crystallinity, thermal, and pasting properties of starches isolated from rice grains with brown, black, and red pericarp. Starch was isolated from the rice grains at initial storage time, and after 6months of storage at different storage temperatures (16, 24, 32 and 40°C). Starch isolated from the grains stored for 6months at 40°C showed darker coloration, surface deformation of granules, and a significant reduction in the extraction yield, final viscosity, enthalpy, and crystallinity, independent of the grain pericarp coloration. The time and storage temperature not influence the swelling power and solubility of starch isolated from grains with brown pericarp, while for the grains with black and red pericarp there was reduction in swelling power and solubility of starches isolated of grains stored at 40°C. Grains stored at 16°C showed minimum changes in starch properties. Copyright © 2016 Elsevier Ltd. All rights reserved.

A structured approach to target starch solubilisation and hydrolysis for the sugarcane industry.

Science.gov (United States)

Cole, Marsha R; Rose, Ingrid; Chung, Yoo Jin; Eggleston, Gillian

2015-01-01

In sugarcane processing, starch is considered an impurity that negatively affects processing and reduces the quality of the sugar end-product. In the last decade, there has been a general world-wide increase in starch concentrations in sugarcane. Industrial α-amylases have been used for many years to mitigate issues arising from starch in the sugarcane industry. Mixed results have prompted further studies of the behaviour of different physical forms of starch and their interactions with α-amylases during processing. By using corn starch as a reference in model juices and syrups, processing parameters, activities, and hydrolysis of insoluble, swollen, and soluble starch forms were evaluated for two commercial α-amylases with high (HT) and intermediate (IT) temperature stability, respectively. The ability of starch to solubilise across a sugarcane factory is largely limited by increased Brix values. Optimum target locations and conditions for the application of α-amylases in sugarcane processing are discussed in detail. Published by Elsevier Ltd.

Effect of pH on paste properties of irradiated corn starch by gamma-rays

International Nuclear Information System (INIS)

Kume, Tamikazu; Aoki, Shohei; Kobayashi, Nobuo; Okuaki, Akira.

1979-01-01

The degradation of starch by γ-irradiation and the effect of pH on gelatinization of starch after irradiation were investigated. Paste viscosities were markedly affected by pH on gelatinization and a decrease in the viscosity of irradiated starch was stimulated by increasing pH. On the other hand, the solubility of irradiated starch increased significantly at the high pH. The granule structure of irradiated starch easily disintegrated at alkaline pH. Remarkable dissolution from the surface of the irradiated starch granules was observed after heating at high pH only a filamentous network frame remained, but the unirradiated one collapsed and folded. It was seen that alkali treatment after irradiation reduces the required dose to obtain low viscosity starch. The required dose to produce a low viscosity starch, for example Ajinomoto Essan Sizer 600 grade, was ca. 3 Mrad at pH 11.0 and ca. 5 Mrad at pH 7.0, whereas it was ca. 7 Mrad without pH adjustment. (author)

Effect of extrusion, espansion and toasting on the nutritional value of peas, faba beans and lupins

Directory of Open Access Journals (Sweden)

Filippo Rossi

2010-01-01

Full Text Available An assessment was made of the effect that different treatments (toasting, expansion, extrusion have on the nutritionalvalue of protein plants (pea, faba bean, lupin. In a randomized block design, feeds were screened for enzymaticdigestibility of starch and protein, N solubility and in vitro protein degradability. Expansion and extrusion cause increasedstarch enzymatic degradability while toasting produced virtually no effects. In peas this value increased from 11.80% inmeal to 39.70% in the extruded product; 85.37% is the percentage for the expanded product, while 10.90% is the starchdigestibility value for toasted peas. In faba beans the extrusion process increased starch digestibility from 11.39% to85.05%, while in extruded lupins a complete starch hydrolysis was obtained, while in the meal the polysaccharide digestionwas 54.48%.The expansion and extrusion processes significantly decreased rumen degradability during the first 8 hours of incubation.Toasted peas had lower degradability if compared with controls but not with the other treatments. The onlypotentially alternative source to soybean is the extruded faba bean. In spite of its lower protein content, this feed ischaracterized by a considerably lower in vitro protein degradability than soybean. This implies that the digestible foodprotein content is comparable (124.90 g/kg DM to that of soybean (109.78 g/kg DM and definitely higher than thatof all other protein plants.

Comparison of Morphology and Physicochemical Properties of Starch Among 3 Arrowhead Varieties.

Science.gov (United States)

Li, Aimin; Zhang, Yunhong; Zhang, Yongji; Yu, Xurun; Xiong, Fei; Zhou, Rumei; Zhang, Yongtai

2016-05-01

Arrowhead (Sagittaria trifolia var. sinensis) is a source of starch worldwide, but arrowhead starch has been rarely studied. In this work, starch was separated from arrowhead corm. The morphology and physicochemical properties of starch were then investigated and compared among 3 different arrowhead varieties (Purple-corm, Hongta, and Japanese). Results showed that starches from the 3 varieties similarly featured an oval shape containing a visible polarization cross, a CA -type crystalline structure, and an ordered structure in the external granule region. However, starch content, granule size, crystal characteristics, and pasting properties differed among the 3 varieties. Japanese arrowhead exhibited the highest starch content and degree of ordered structure in the external granule region, as well as onset, peak, and final gelatinization temperature. Purple-corm arrowhead starch demonstrated the highest amylose content and relative degree of crystallinity, smallest granule size, and lowest swelling power and solubility. Purple-corm arrowhead starch also showed the highest gelatinization enthalpy, as well as peak, trough, final, and setback viscosities. This starch further presented the lowest breakdown viscosity and degree of hydrolysis by HCl and porcine pancreatic α-amylase. These findings can provide useful references for arrowhead variety selection in food and nonfood industries. © 2016 Institute of Food Technologists®

APPLICATION OF OAT, WHEAT AND RYE BRAN TO MODIFY NUTRITIONAL PROPERTIES, PHYSICAL AND SENSORY CHARACTERISTICS OF EXTRUDED CORN SNACKS.

Science.gov (United States)

Makowska, Agnieszka; Polcyn, Anna; Chudy, Sylwia; Michniewicz, Jan

2015-01-01

Cereal products constitute the basis of the diet pyramid. While the consumption of such products as bread decreases, the group of food which popularity increase is cereal snacks. Unfortunately, the dietary value of this group of foodstuffs is limited. Thus, different types of cereal bran may be added to the produced snacks to enhance their nutritive value. However, an addition of bran may have an adverse effect on quality attributes of products. Corn grits enriched with 20 and 40% oat, wheat and rye bran was extruded. Basic parameters determining the nutritive value, physical characteristics and sensory attributes of the six produced types of extrudates were measured and compared. Moreover, the effect of additives applied on viscosity of aqueous suspensions of the raw materials and extrudates under controlled conditions was measured using RVA. The dietary value of snacks containing bran depends on the type and quantitative shares of the additives. The content of dietary fibre in produced extrudates ranged from 6.5 to 15.8%, including soluble dietary fibre at 2.1 to 3.7%. With an increase of bran content in extrudates, their expansion decreased, density increased and the colour of extrudates changed (reduced brightness, increased a*, decreased b*). In sensory evaluation the highest acceptability was given to extrudates with a 20% addition of oat bran, while the lowest was given for those with 40% wheat bran. Based on PCA results positive correlations were found between overall desirability and crispiness, porosity, taste, colour and expansion. Negative correlations between desirability and hardness and density of extrudates were observed. The additives and their level also had an effect on changes in viscosity of aqueous suspensions measured using RVA. However, no correlation was found between quality features of extrudates and values of attributes measured in the analysis of viscosity. In the production of corn extruded snacks an addition of oat, wheat and rye bran

Modification of cassava starch using combination process lactic acid hydrolysis and micro wave heating to increase coated peanut expansion quality

Science.gov (United States)

Sumardiono, Siswo; Pudjihastuti, Isti; Jos, Bakti; Taufani, Muhammad; Yahya, Faad

2017-05-01

Modified cassava starch is very prospective products in the food industry. The main consideration of this study is the increasing volume of imported wheat and the demand for modified cassava starch industry. The purpose of this study is the assessing of lactic acid hydrolysis and microwave heating impact to the physicochemical and rheological properties of modified cassava starch, and test applications of modified cassava starch to coated peanut expansion quality. Experimental variables include the concentration of lactic acid (0.5% w/w, 1% w/w; 2% w/w), a time of hydrolysis (15, 30, 45 minutes), a time of microwave heating (1, 2, 3 hours). The research step is by dissolving lactic acid using aquadest in the stirred tank reactor, then added cassava starch. Hydrolysed cassava starch was then heated by microwave. Physicochemical properties and rheology of the modified cassava starch is determined by the solubility, swelling power, and test congestion. The optimum obtained results indicate that solubility, swelling power, congestion test, respectively for 19.75%; 24.25% and 826.10% in the hydrolysis treatment for 15 minutes, 1% w lactic acid and microwave heating 3 hours. The physicochemical and rheological properties of modified cassava starch have changed significantly when compared to the native cassava starch. Furthermore, these modified cassava starch are expected to be used for the substitution of food products.

EFFECT OF ADDITION OF PROTEIN PREPARATIONS ON THE QUALITY OF EXTRUDED MAIZE EXTRUDATES

Directory of Open Access Journals (Sweden)

Elżbieta Rytel

2013-02-01

Full Text Available The method of extrusion enables enrichment of snacking products with protein preparation simultaneously providing a high quality of end products. Maize semolina with particle size of 500-1250 μm was used as raw material and as additives soybean protein isolate, distillery yeast Safethanol 3035 and laboratory obtained potato protein preparation. Snacks were determined for contents of dry matter, protein, fat as well as for texture, volume weight, bulk density and sensory traits. The application of 3% and 6% additions of protein preparations in extruded snacks production was found to exert a beneficial effect on their chemical composition without deteriorating sensory characteristics. The higher, 6%, addition of proteins to extrudates turned out to significantly reduce content of fat (by 18% and ash (by 50%, and to increase total protein content by 26%, on average, in the products examined as compared to the samples free of additives. The addition of potato protein to extrudates, especially at the higher dose (6%, significantly improved their consistency and texture, simultaneously diminishing the expansion ratio of ready products. The higher (6% addition of yeast protein applied in the production of extrudates resulted in slight deterioration of their taste and aroma, yet had a positive effect on the structure and expansion ratio of the ready products. The extrudates produced with the addition of soybean protein were characterized by a good expansion ratio, uniform structure, irrespective of preparation dose and simultaneously demonstrated lower bulk mass as compared to the other products obtained in the experiment.

Calcium modified edible Canna (Canna edulis L) starch for controlled released matrix

Science.gov (United States)

Putri, A. P.; Ridwan, M.; Darmawan, T. A.; Darusman, F.; Gadri, A.

2017-07-01

Canna edulis L starch was modified with calcium chloride in order to form controlled released matrix. Present study aim to analyze modified starch characteristic. Four different formulation of ondansetron granules was used to provide dissolution profile of controlled released, two formula consisted of 15% and 30% modified starch, one formula utilized matrix reference standards and the last granules was negative control. Methocel-hydroxypropyl methyl cellulose was used as controlled released matrix reference standards in the third formula. Calcium starch was synthesized in the presence of sodium hydroxide to form gelatinized mass and calcium chloride as the cross linking agent. Physicochemical and dissolution properties of modified starch for controlled released application were investigated. Modified starch has higher swelling index, water solubility and compressibility index. Three of four different formulation of granules provide dissolution profile of controlled released. The profiles indicate granules which employed calcium Canna edulis L starch as matrix are able to resemble controlled drug released profile of matrix reference, however their bigger detain ability lead to lower bioavailability.

Effects of pH and Salts on Physical and Mechanical Properties of Pea Starch Films.

Science.gov (United States)

Choi, W S; Patel, D; Han, J H

2016-07-01

To identify the significant contribution of intermolecular hydrogen bonds of starch molecules to the film structure formation, pH of film-forming solutions was adjusted and also various salts (NaCl, CaCl2 , CaSO4 , and K2 SO4 ) were mixed into the glycerol-plasticized pea starch film. The film made from pH 7 possessed the highest tensile strength-at-break (2 times) and elastic modulus (4 to 15 times) and the lowest elongation-at-break compared with those of the films made from acid and alkali environments. The pH 7 film also has the highest film density and the lowest total soluble matter. At the level of 0.01 to 0.1 M of CaSO4 and 0.1 M of K2 SO4 in a kilogram of starch, the water solubility of the film increased, while chloride salts slightly lowered the solubility. NaCl and CaSO4 reduced water vapor permeability (WVP), while CaCl2 slightly increased WVP at 0.01 and 0.06 M concentrations, and K2 SO4 significantly increased WVP at 0.03 and 0.15 M. Presence of salts increased tensile strength (5 to 14 times than the control films) and elastic modulus (35 to 180 times) of starch film at 0.01 to 0.03 M of CaSO4 and K2 SO4 . Elongation-at-break increased significantly as salt concentration increases to an optimal level. However, when the concentration exceeded above the optimal level, the E of starch films decreased and showed no significant difference from the control film. Overall, the addition of salts modified physical and mechanical properties of pea starch films more than pH adjustment without any salt addition. © 2016 Institute of Food Technologists®

VAPOR MIXER FOR GELATINIZATION OF STARCH IN LIQUEFYING STATION

Directory of Open Access Journals (Sweden)

V. V. Ananskikh

2015-01-01

Full Text Available Starch hydrolysis is main technological process in production of starch sweeteners. Acid hydrolysis of starch using hydrochloric acid is carried out very fast but it does not allow to carry out full hydrolysis and to produce products with given carbohydrate composition. Bioconversion of starch allows to eliminate these limitations. At production of starch sweeteners from starch using enzymes starch hydrolysis is carried out in two stages At first starch – starch liquefaction the rapid increase of viscosity takes place which requires intensive mixing. Liquefying station consists of jet-cooker, holder, pressure regulator and evaporator. Jet-cooker of starch is its main part, starch is quickly turns into soluble (gelatinized state and it is partially liquefied by injection of starch suspension by flow of water vapor under pressure not less than 0,8 MPa. Heat and hydraulic calculation were carried out in order to determine constructive sizes of mixer for cooking of starch. The main hydraulic definable parameters are pressure drop in mixer, vapor pressure at mixer inlet, daily capacity of station by glucose syrup M, product consumption (starch suspension, diameter of inlet section of vapor nozzle. The goal of calculation was to determine vapor consumption M1, diameter d2 of outlet section of confuser injector, length l2 of gelatinization section. For heat calculation there was used Shukhov’s formula along with heat balance equation for gelatinization process. The numerical solution obtained with adopted assumptions given in applied mathematical package MATHCAD, for M = 50 t/day gives required daily vapor consumption M1 = 14,446 т. At hydraulic calculation of pressure drop in mixer there was used Bernoulli’s theorem. Solving obtained equations using MATHCAD found diameter of outlet section of consufer d2 = 0,023 м, vapor pressure inside of mixer p2 = 3,966·105 Па, l2 = 0,128 м. Developed method of calculation is used to determine

Relationships between the physical forms of starch and performance of carbonatation clarification and press filtration at the refinery

Science.gov (United States)

Laboratory studies were conducted to underpin if and how the different physical forms of starch (insoluble or soluble) affected carbonatation clarification and press filtration, by using simulated melt liquors. Carbonatated liquors containing =250 ppm/Brix (USDA starch research method) of total sta...

Effect of Ultrasound on Physicochemical Properties of Wheat Starch

Directory of Open Access Journals (Sweden)

Mahsa Majzoobi

2014-04-01

Full Text Available Application of ultrasound process is growing in food industry for different purposes including homogenization, extraction, blanching and removal of microorganisms, etc. On the other hand, starch is a natural polymer which exists in many foods or added into the food as an additive. Therefore, determination of the effects of ultrasound on starch characteristics can be useful in interpretation of the properties of starch-containing products. The main aim of this study was to determine the physicochemical changes of wheat starch treated by ultrasound waves. Therefore, an ultrasound probe device was used which ran at 20 kHz, 100 W and 22°C. Starch suspension in distilled water (30% w/w was prepared and treated with ultrasound for 5, 10, 15 and 20 min. The results showed that increases in processing duration led to increases in water solubility of starch, water absorption and gel clarity (as determined by spectrophotometry. Starch intrinsic viscosity as measured using an Ostwald U-tube showed lower intrinsic viscosity with increases in ultrasound time. Gel strength of the samples as determined using a texture analyzer was reduced by longer processing time. The scanning electron microscopy revealed that increasing the duration time of the ultrasound treatment could produce some cracks and spots on the surface of the granules. In total, it was concluded that the ultrasound treatment resulted in some changes from the starch granular scale to molecular levels. Some of the starch molecules were degraded upon ultrasound processing. Such changes may be observed for the starch-containing foods treated with ultrasound and they are enhanced with increases in ultrasound time intervals.

Effect of Acacia Gum, NaCl, and Sucrose on Physical Properties of Lotus Stem Starch

Science.gov (United States)

Gill, Balmeet Singh

2014-01-01

Consumer preferences in east Asian part of the world pave the way for consumption of lotus stem starch (LSS) in preparations such as breakfast meals, fast foods, and traditional confectioneries. The present study envisaged the investigation and optimization of additives, that is, acacia gum, sodium chloride (NaCl), and sucrose, on water absorption (WA), water absorption index (WAI), and water solubility index (WSI) of LSS employing response surface methodology (RSM). Acacia gum resulted in increased water uptake and swelling of starch; however, NaCl reduced the swelling power of starch by making water unavailable to starch and also due to starch-ion electrostatic interaction. Sucrose restricted the water absorption by binding free water and decreased amylose leaching by building bridges with starch chains and thus forming rigid structure. PMID:26904639

Extrusion Conditions and Amylose Content Affect Physicochemical Properties of Extrudates Obtained from Brown Rice Grains

Directory of Open Access Journals (Sweden)

Rolando José González

2013-01-01

Full Text Available The utilization of whole grains in food formulations is nowadays recommended. Extrusion cooking allows obtaining precooked cereal products and a wide range of ready-to-eat foods. Two rice varieties having different amylose content (Fortuna 16% and Paso 144, 27% were extruded using a Brabender single screw extruder. Factorial experimental design was used to study the effects of extrusion temperature (160, 175, and 190°C and grits moisture content (14%, 16.5%, and 19% on extrudate properties. Specific mechanical energy consumption (SMEC, radial expansion (E, specific volume (SV, water absorption (WA, and solubility (S were determined on each extrudate sample. In general, Fortuna variety showed higher values of SMEC and S (703–409 versus 637–407 J/g; 33.0–21.0 versus 20.1–11.0%, resp. than those of Paso 144; on the contrary SV (8.64–3.47 versus 8.27–4.53 mL/g and WA tended to be lower (7.7–5.1 versus 8.4–6.6 mL/g. Both varieties showed similar values of expansion rate (3.60–2.18. Physical characteristics depended on extrusion conditions and rice variety used. The degree of cooking reached by Paso rice samples was lower than that obtained for Fortuna. It is suggested that the presence of germ and bran interfered with the cooking process, decreasing friction level and broadening residence time distribution.

Preparation of an extruded fish snack using twin screw extruder and the storage characteristics of the product

OpenAIRE

Sharma, S.K.; Basu, S.

2003-01-01

A value-added extruded fish product was prepared with corn flour (80%) and fish (sciaenid) powder (20%), using a twin-screw extruder. The effect of different parameters like moisture, temperature, fish powder concentration, speed of the extruder and die-diameter on expansion ratio and crisp texture were studied. The storage characteristics of the final product were studied using three different types of packaging under nitrogen flushing. The study revealed that aluminum foil is the best packa...

Characterization of chestnut (Castanea sativa, mill starch for industrial utilization

Directory of Open Access Journals (Sweden)

Demiate Ivo Mottin

2001-01-01

Full Text Available Studies were conducted to characterize the chestnut and its starch. Chemical composition of the chestnuts showed high level of starch. Moisture level in the raw nuts was around 50g/100g in wet basis and starch content, around 80g/100g in dry basis; other nut flour components were protein (5.58 g/100g, lipid (5.39 g/100g, crude fiber (2.34 g/100g and ash (2.14 g/100g. Starch fraction was chemically characterized in order to identify the granule quality as compared with those of cassava and corn. This fraction showed more lipids and proteins than the other starches. Chestnut starch granules showed peculiar shape, smaller than the control starches and low amount of damaged units. Chemical composition concerning amylose : amylopectin ratio was intermediate to that presented by cassava and corn starch granules. Water absorption at different temperatures as well as solubility were also intermediate but closer to that presented by cassava granules. The same behavior was observed in the interaction with dimethyl-sulfoxide. Native starch granules and those submitted to enzymatic treatment with commercial alpha-amylase and also with enzymes from germinated wheat were observed by scanning electronic microscopy. Water suspensions of chestnut starch granules were heated to form pastes that were studied comparatively to those obtained with cassava and corn starches. Viscographic pattern of chestnut starch pastes showed a characteristic profile with high initial viscosity but peak absence, high resistance to mechanical stirring under hot conditions and high final viscosity. There was no way to compare it with the paste viscographic profiles obtained with the control starches. Chestnut starch pastes were stable down to pH 4 but unstable at pH 3. The water losses observed in the chestnut starch pastes after freeze-thaw cycles showed more similarity to the pattern observed in corn starch pastes as well as clarity and strength of the gel. In general the results

Effect of dual modification with hydroxypropylation and cross-linking on physicochemical properties of taro starch.

Science.gov (United States)

Hazarika, Bidyut Jyoti; Sit, Nandan

2016-04-20

Dual modification of taro starch by hydroxypropylation and cross-linking was carried out and the properties of the modified starches were investigated. Two different levels of hydroxypropylation (5 and 10%) and cross-linking (0.05 and 0.10%) were used in different sequences. The amylose contents of the starch decreased due to single and dual modification. For the dual-modified starches, the swelling, solubility and clarity was found to increase with level of hydroxypropylation and decrease with level of cross-linking. The freeze-thaw stability of the dual-modified starches was also affected by the sequence of modification. The viscosities of the cross-linked and dual-modified starches were more than native and hydroxypropylated starches. The firmness of the dual-modified starches was also higher than native and single modified starches. The dual-modified starches have benefits of both type of modifications and could be used for specific purposes e.g. food products requiring high viscosity as well as freeze-thaw stability. Copyright © 2015 Elsevier Ltd. All rights reserved.

The regulation mechanisms of soluble starch and glycerol for production of azaphilone pigments in Monascus purpureus FAFU618 as revealed by comparative proteomic and transcriptional analyses.

Science.gov (United States)

Huang, Zi-Rui; Zhou, Wen-Bin; Yang, Xue-Ling; Tong, Ai-Jun; Hong, Jia-Li; Guo, Wei-Ling; Li, Tian-Tian; Jia, Rui-Bo; Pan, Yu-Yang; Lin, Jun; Lv, Xu-Cong; Liu, Bin

2018-04-01

Monascus spp. have been used for thousands of years as a traditional food additive in China. This mold can produce many different types of commercially valuable secondary metabolites of biological activity. Soluble starch and glycerol are the two principal carbon sources universally utilized by Monascus for the production of beneficial metabolites. In this study, the effects and regulation mechanisms of soluble starch and glycerol for M. purpureus FAFU618 on Monascus azaphilone pigments (MonAzPs) were investigated through ultra-performance liquid chromatography quadrupole time of flight mass spectrometry (UPLC-QTOF-MS/MS), comparative proteomics and quantitative real-time reverse transcription polymerase chain reaction (RT-qPCR). The production of intracellular and extracellular pigments was significantly different between the soluble starch group (SSG) and glycerol group (GCG). Additionally, the components of intracellular pigments revealed by UPLC-QTOF-MS/MS showed that Monascin and Ankaflavin increased significantly in the GCG, while Rubropunctatin and Monascorubrin increased in the SSG. Differentially expressed proteins of mycelia between SSG and GCG were analyzed by two-dimensional gel electrophoresis (2-DE) and MALDI-TOF/TOF MS. We identified 27 proteins with statistically altered expression, of which 18 proteins associated with the EMP (glycolytic pathway), translation, energy generation, proteolysis, etc. were up-regulated, and 9 proteins, including ribosomal proteins, heat shock proteins (HSPs) and others, were down-regulated in GCG. Meanwhile, the expression levels of MonAzP biosynthetic genes were also analyzed by RT-qPCR, and the results showed that mppA, mppC, mppR1 and mppR2 were down-regulated, whereas genes MpPKS5, MpFasA2, MpFasB2, mppB, mppD and mppE were up-regulated. Collectively, these findings illustrate that the regulation of MonAzPs is not only closely related to the expression levels of certain proteins in the polyketide synthesis pathway

Structural and Digestion Properties of Soluble-, Slowly Digestible and Resistant Maltodextrin from Cassava Starch by Enzymatic Modification

DEFF Research Database (Denmark)

Sorndech, Waraporn

The combination of branching enzyme (BE) and amylomaltase (AM) were selected to modify cassava starch. AM were used to elongate the glucan chains in order to enhance BE activity to create branching linkages. Cassava starch were gelatinized and incubated with BE or AMBE or BEAMBE or simultaneous...... AM and BE. The molecular analysis of the products including amylopectin chain length distribution, content of α-1,6 glucosidic linkages, absolute molecular weight distribution and digestibility were examined. Only BE catalysis showed 7.8% of branching linkages. The sequential AMBE-treated starch...... showed 9.9%-10.0% branching linkages, while the sequential BEAMBE-treated starch gained 10.9%-13.1% of branching linkages. Moreover, the sequential AMBE and BEAMBE-treated starch retarded the digestion rate of α-amylase and glucoamylase. Overall, sequential BEAMBE catalysis resulted in more...

Preparation and Characterization of Some Polyethylene Modified- Starch Biodegradable Films

International Nuclear Information System (INIS)

Badrana, A.S.; Ramadanb, A.M.; Ibrahim, N.A.; Kahild, T.; Hussienc, H.A.

2005-01-01

Blends of LDPE with soluble starch, wheat flour and commercial starch were prepared by mixing starch (or flour) with styrene then blending the mixture with LDPE, The starch percents vary between 5 and 50% of the total weight. Their physical and mechanical properties were recorded and compared with pure LDPE. It was observed that the increase in starch or wheat flour contents of the mixture was reversibly proportional to the tensile strength and % elongation. Samples were tested for water absorption. All of the samples were insoluble in cold and boiling water. Moisture uptake increased with immersion time and increasing starch content. The changes in the tensile strength of LDPE/starch (or wheat flour) after the course of thermal oxidation was measured. These results show negligible changes in the tensile strength of the control sample as compared to that of the samples containing the additives. Oxidation processes take advantage of the high temperatures (40-50 degree C) and the time. It was also observed that after 10 weeks of soil burial, the mechanical properties of the films decrease, mainly, due to starch removal from the films. Also, for the weight loss a drastic decrease was observed after 10 weeks of soil burial thereafter it preceded slowly. The LDPE/ starch strips showed weight loss after treating with a-amylase this due to hydrolysis and leaching of the starch. The rate of starch hydrolysis increases with the increase in starch content of the sample. The influence of addition of starch on the overall migration of these films, with different food simulant, was studied, at different temperatures (-4 degree. 25 degree and 40 degree C). All values were significantly lower than the upper limit for overall migration set by the EU (10 mg/dirf) for food grade plastics packaging materials

Starch granules size distribution in superior and inferior grains of wheat is related to enzyme activities and their gene expressions during grain filling

DEFF Research Database (Denmark)

Zhang, Chuanhui; Jiang, Dong; Liu, Fulai

2010-01-01

with the temporally change patterns of starch synthase activities and relative gene expression levels. For instance, activities of soluble and granule-bound starch synthases (designated SSS and GBSS) peaked at 20 and 24 DAF. Genes encoding isoforms of starch synthases expressed at different grain filling periods...

Physicochemical Properties of Flaxseed Fortified Extruded Bean Snack

OpenAIRE

Vadukapuram, Naveen; Hall, CliffordIII; Tulbek, Mehmet; Niehaus, Mary

2014-01-01

Milled flaxseed was incorporated (0?20%) into a combination of bean-corn flours and extruded in a twin screw extruder using corn curl method. Physicochemical parameters such as water activity, color, expansion ratio, bulk density, lipid content, and peroxide values of extruded snack were analyzed. Scanning electron micrographs were taken. Peroxide values and propanal contents were measured over four months of storage. Rancidity scores of extruded snack were measured using a trained panel. As ...

Effect of guar and xanthan gums on functional properties of mango (Mangifera indica) kernel starch.

Science.gov (United States)

Nawab, Anjum; Alam, Feroz; Haq, Muhammad Abdul; Hasnain, Abid

2016-12-01

The effects of different concentrations of guar and xanthan gums on functional properties of mango kernel starch (MKS) were studied. Both guar and xanthan gum enhanced the water absorption of MKS. The addition of xanthan gum appeared to reduce the SP (swelling power) and solubility at higher temperatures while guar gum significantly enhanced the SP as well as solubility of MKS. The addition of both gums produced a reinforcing effect on peak viscosity of MKS as compared to control. Pasting temperature of MKS was higher than that of starch modified by gums indicating ease of gelatinization. Guar gum played an accelerative effect on setback but xanthan gum delayed the setback phenomenon during the cooling of the starch paste. Both gums were found to be effective in reducing the syneresis while gel firmness was markedly improved. Copyright © 2016 Elsevier B.V. All rights reserved.

Some physicochemical and rheological properties of starch isolated from avocado seeds.

Science.gov (United States)

Chel-Guerrero, Luis; Barbosa-Martín, Enrique; Martínez-Antonio, Agustino; González-Mondragón, Edith; Betancur-Ancona, David

2016-05-01

Seeds from avocado (Persea americana Miller) fruit are a waste byproduct of fruit processing. Starch from avocado seed is a potential alternative starch source. Two different extraction solvents were used to isolate starch from avocado seeds, functional and rheological characteristics measured for these starches, and comparisons made to maize starch. Avocado seed powder was suspended in a solution containing 2 mM Tris, 7.5 mM NaCl and 80 mM NaHSO3 (solvent A) or sodium bisulphite solution (1500 ppm SO2, solvent B). Solvent type had no influence (p>0.05) on starch properties. Amylose content was 15-16%. Gelatinization temperature range was 56-74 °C, peak temperature was 65.7 °C, and transition enthalpy was 11.4-11.6J/g. At 90 °C, solubility was 19-20%, swelling power 28-30 g water/g starch, and water absorption capacity was 22-24 g water/g starch. Pasting properties were initial temperature 72 °C; maximum viscosity 380-390 BU; breakdown -2 BU; consistency 200 BU; and setback 198 BU. Avocado seed starch dispersions (5% w/v) were characterized as viscoelastic systems, with G'>G″. Avocado seed starch has potential applications as a thickening and gelling agent in food systems, as a vehicle in pharmaceutical systems and an ingredient in biodegradable polymers for food packaging. Copyright © 2016. Published by Elsevier B.V.

A physicochemical study of sugar palm (Arenga Pinnata) starch films plasticized by glycerol and sorbitol

Science.gov (United States)

Poeloengasih, Crescentiana D.; Pranoto, Yudi; Hayati, Septi Nur; Hernawan, Rosyida, Vita T.; Prasetyo, Dwi J.; Jatmiko, Tri H.; Apriyana, Wuri; Suwanto, Andri

2016-02-01

The present work explores the physicochemical characteristics of sugar palm starch film for a potential hard capsule purpose. Sugar palm (Arenga pinnata) starch films were plasticized with glycerol or sorbitol in various concentrations (30% up to 50% w/w starch). Their effects on physicochemical properties of the films were investigated. The results showed that sugar palm starch was successfully developed as the main material of film using casting method. Incorporation of both glycerol or sorbitol affected the properties of films in different ways. It was found that thickness and solubility increased as plasticizer concentration increased, whereas retraction ratio, swelling degree and swelling thickness decreased with the increased plasticizer concentration.

Preparation of donut-shaped starch microparticles by aqueous-alcoholic treatment.

Science.gov (United States)

Farrag, Yousof; Sabando, Constanza; Rodríguez-Llamazares, Saddys; Bouza, Rebeca; Rojas, Claudio; Barral, Luís

2018-04-25

A simple method for producing donut-shaped starch microparticles by adding ethanol to a heated aqueous slurry of corn starch is presented. The obtained microparticles were analysed by SEM, XRD and DSC. The average size of microparticles was 14.1 ± 0.3 μm with holes of an average size of 4.6 ± 0.2 μm. The crystalline arrangement of the microparticles was of a V-type single helix. The change in crystallinity from A-type of the starch granules to a more open structure, where water molecules could penetrate easier within the microparticles, substantially increased their solubility and swelling power. The microparticles exhibited a higher gelatinization temperature and a lower gelatinization enthalpy than did the starch granules. The donut-shaped microparticles were stable for more than 18 months and can be used as a carrier of an active compound or as a filler in bioplastics. Copyright © 2017 Elsevier Ltd. All rights reserved.

Preparation and properties of blends of polypropylene and acrylonitril-butadiene-styrene with thermoplastic starch

International Nuclear Information System (INIS)

Kaseem, M.; Deri, F.

2012-01-01

In the present work the rheological and mechanical properties of polypropylene / thermoplastic starch (PP/TPS) and acrylo nitril-butadiene-styrene/ thermoplastic starch (ABS/TPS) blends were investigated. Starch was plasticised using glycerol and blends were prepared using a laboratory scale with single screw extruder. Rheological properties of the prepared blends were determined using a capillary rheometer. Mechanical properties were studied in term of tensile tests, stress at break, strain at break and young's modulus were determined. Rheological results showed that the blends are pseudo plastic in manner and the true viscosity of Pp/TPS blend decreases with increasing TPS content in the blend until 10%, and at more than 10% TPS it increases with increasing TPS. In ABS/TPS, the true viscosity decreases with increasing TPS content in the blend. The mechanical results showed that in both systems, the stress at break and strain at break decrease with increasing TPS content in the blend while the young's modulus increases with increasing TPS content. The mechanical results shown that the addition of TPS to each of PP and ABS follows the general trend for filler effects on polymer properties. (author)

Chemical, morphological, rheological and thermal properties of Solanum lycocarpum phosphorylated starches

Directory of Open Access Journals (Sweden)

Diego Palmiro Ramirez Ascheri

2014-08-01

Full Text Available The increasing need for starches with specific characteristics makes it important to study unconventional starches and their modifications in order to meet consumer demands. The aim of this work was to study physicochemical characteristics of native starch and phosphate starch of S. lycocarpum. Native starch was phosphated with sodium tripolyphosphate (5-11% added with stirring. Chemical composition, morphology, density, binding ability to cold water, swelling power and solubility index, turbidity and syneresis, rheological and calorimetric properties were determined. Phosphorus was not detected in the native sample, but the phosphating process produced modified starches with phosphorus contents of 0.015, 0.092 and 0.397%, with the capacity of absorbing more water, either cold or hot. Rheological data showed the strong influence of phosphorus content on viscosity of phosphate starch, with lower pasting temperature and peak viscosity higher than those of native starch. Enthalpy was negatively correlated with the phosphorus content, requiring 9.7; 8.5; 8.1 and 6.4 kJ g-1 of energy for the transition from the amorphous to the crystalline state for the starch granules with phosphorus contents of 0; 0.015; 0.092 and 0.397%, respectively. Cluster analysis and principal component analysis showed that starches with 0.015 and 0.092% phosphorus have similar characteristics and are different from the others. Our results show that the characteristics of phosphate modified S. lycocarpum starch have optimal conditions to meet the demands of raw materials, which require greater consistency in stickiness, combined with low rates of retrogradation and syneresis.

The impact of extrusion on the nutritional composition, dietary fiber and in vitro digestibility of gluten-free snacks based on rice, pea and carob flour blends.

Science.gov (United States)

Arribas, C; Cabellos, B; Sánchez, C; Cuadrado, C; Guillamón, E; Pedrosa, M M

2017-10-18

Consumers and the food industry are demanding healthier products. Expanded snacks with a high nutritional value were developed from different rice, pea and carob flour blends. The proximate composition, starch (total and resistant), amylose and amylopectin, dietary fiber (soluble and insoluble) contents, and the in vitro protein digestibility of different rice-legume formulations, were evaluated before and after the extrusion process. Compared with the corresponding non-extruded blends (control), the extrusion treatment did not change the total protein content, however, it reduced the soluble protein (61-86%), the fat (69-92%) and the resistant starch contents (100%). The total starch content of all studied blends increased (2-19%) after extrusion. The processing increased the in vitro protein digestibility, reaching values around 88-95% after extrusion. Total dietary fiber was reduced around 30%, and the insoluble fraction was affected to a larger extent than the soluble fraction by the extrusion process. Because of its balanced nutritional composition, high dietary fiber content, as well as low energy density, these novel gluten-free snack-like foods could be considered as functional foods and a healthier alternative to commercially available gluten-containing or gluten-free and low nutritional value snacks.

The "Food Polymer Science" approach to the practice of industrial R&D, leading to patent estates based on fundamental starch science and technology.

Science.gov (United States)

Slade, Louise; Levine, Harry

2018-04-13

This article reviews the application of the "Food Polymer Science" approach to the practice of industrial R&D, leading to patent estates based on fundamental starch science and technology. The areas of patents and patented technologies reviewed here include: (a) soft-from-the-freezer ice creams and freezer-storage-stable frozen bread dough products, based on "cryostabilization technology" of frozen foods, utilizing commercial starch hydrolysis products (SHPs); (b) glassy-matrix encapsulation technology for flavors and other volatiles, based on structure-function relationships for commercial SHPs; (c) production of stabilized whole-grain wheat flours for biscuit products, based on the application of "solvent retention capacity" technology to develop flours with reduced damaged starch; (d) production of improved-quality, low-moisture cookies and crackers, based on pentosanase enzyme technology; (e) production of "baked-not-fried," chip-like, starch-based snack products, based on the use of commercial modified-starch ingredients with selected functionality; (f) accelerated staling of a starch-based food product from baked bread crumb, based on the kinetics of starch retrogradation, treated as a crystallization process for a partially crystalline glassy polymer system; and (g) a process for producing an enzyme-resistant starch, for use as a reduced-calorie flour replacer in a wide range of grain-based food products, including cookies, extruded expanded snacks, and breakfast cereals.

Using different fibers to replace fat in sponge cakes: In vitro starch digestion and physico-structural studies.

Science.gov (United States)

Diez-Sánchez, Elena; Llorca, Empar; Quiles, Amparo; Hernando, Isabel

2018-01-01

This study assessed the effect of substituting 30% of fat by soluble, insoluble fiber, or a mix of both fibers in sponge cake quality, structure, acceptability, and starch digestibility. The apparent viscosity of the different formulations was measured and micro-baking was simulated. Texture profile tests were carried out and the crumb structure was examined. In vitro digestion was performed to study the digestibility of starch and a sensory test was carried out to know consumer acceptance. The soluble fiber (maltodextrin) affected the structure and quality of the cakes less than the insoluble fiber (potato fiber) and the use of soluble fiber in the formulation resulted in lower glucose release under in vitro conditions. Moreover, the consumer did not find differences among the control cake and the cakes prepared with soluble fiber. Considering the results as a whole, soluble fiber may be used for partial replacement of fat in sponge cake formulations and may constitute an appropriate strategy for obtaining healthy sponge cakes.

Regulatory effect of amino acids on the pasting behavior of potato starch is attributable to its binding to the starch chain.

Science.gov (United States)

Ito, Azusa; Hattori, Makoto; Yoshida, Tadashi; Watanabe, Ayako; Sato, Ryoichi; Takahashi, Koji

2006-12-27

The binding of an amino acid, glycine (Gly), alanine (Ala), epsilon-aminocaproic acid (-AC), monosodium glutamate (GluNa), or lysine (Lys), to starch was examined by a biomolecular interaction analyzer (IAsys). A starch sample (ATS) hydrolyzed to an extent of 1% hydrolysis rate with 15% sulfuric acid was used as a model starch for the binding examination. The reducing end of ATS was oxidized by the Somogyi reagent, and the conversion of the reducing end to the carboxyl group of ATS was confirmed by a carboxylic acid fluorescence labeling reagent. The oxidized ATS was immobilized to the amino group of a sensor cuvette by using water-soluble carbodiimide and N-hydroxysuccinimide through an amide bond. The IAsys examination showed that Gly, Ala, and epsilon-AC scarcely bound to the immobilized starch chains but that GluNa and Lys favorably bound with their increasing concentrations. The relative binding index (RBI) of each amino acid was defined by the ratio of the slope of the linear regression equation between the binding response and the concentration for each amino acid to that for Gly. Because the relationships between the RBI and the pasting characteristics (pasting temperature, peak viscosity, breakdown, and swelling index) could each be expressed by a linear regression equation with a high correlation coefficient, it is concluded that the regulation of the pasting behavior of starch with an amino acid is caused by binding of the amino acid to the starch chains.

TEXTURE ANALYSIS OF EXTRUDED APPLE POMACE - WHEAT SEMOLINA BLENDS

Directory of Open Access Journals (Sweden)

Ivan Bakalov

2016-03-01

Full Text Available Apple pomace - wheat semolina blends were extruded in a laboratory single screw extruder (Brabender 20 DN, Germany. Effects apple pomace content, moisture content, screw speed, and temperature of final cooking zone on texture of extrudates were studied applying response surface methodology. The texture characteristics of the extrudates were measured using a TA.XT Plus Texture Analyser, Stable Micro Systems.

Extruding plastic scintillator at Fermilab

International Nuclear Information System (INIS)

Pla-Dalmau, Anna; Bross, Alain D.; Rykalin, Viktor V.

2003-01-01

An understanding of the costs involved in the production of plastic scintillators and the development of a less expensive material have become necessary with the prospects of building very large plastic scintillation detectors. Several factors contribute to the high cost of plastic scintillating sheets, but the principal reason is the labor-intensive nature of the manufacturing process. In order to significantly lower the costs, the current casting procedures had to be abandoned. Since polystyrene is widely used in the consumer industry, the logical path was to investigate the extrusion of commercial-grade polystyrene pellets with dopants to yield high quality plastic scintillator. This concept was tested and high quality extruded plastic scintillator was produced. The D0 and MINOS experiments are already using extruded scintillator strips in their detectors. An extrusion line has recently been installed at Fermilab in collaboration with NICADD (Northern Illinois Center for Accelerator and Detector Development). This new facility will serve to further develop and improve extruded plastic scintillator. This paper will discuss the characteristics of extruded plastic scintillator and its raw materials, the different manufacturing techniques and the current R andD program at Fermilab

Physicochemical properties of sugar palm starch film: Effect of concentration and plasticizer type

Science.gov (United States)

Prasetyo, D. J.; Apriyana, W.; Jatmiko, T. H.; Hernawan; Hayati, S. N.; Rosyida, V. T.; Pranoto, Y.; Poeloengasih, C. D.

2017-07-01

In order to find the best formula for capsule shell production, this present work dealt with exploring physicochemical properties of sugar palm (Arenga pinnata) starch film as a function of different kinds and various concentrations of plasticizers. The films were prepared by casting method at different formula: starch 9-11%, glycerol or sorbitol 35-45% and polyethylene-glycol 400 (PEG 400) 5-9%. Appearance, thickness, retraction ratio, moisture content, swelling behavior and solubility of the film in water were analyzed. Both glycerol and sorbitol are compatible with starch matrix. On the contrary, PEG 400 did not form a film with suitable characteristics. The result reveals that glycerol- and sorbitol-plasticized films appeared translucent, homogenous, smooth and slightly brown in all formulas. Different type and concentration of plasticizers altered the physicochemical of film in different ways. The sorbitol-plasticized film had lower moisture content (≤ 10%) than that of glycerol-plasticized film (≥ 18%). In contrast, film plasticized with sorbitol showed higher solubility in water (28-35%) than glycerol-plasticized film (22-28%). As the concentration of both plasticizers increased, there was an increasing tendency on thickness and solubility in water. Conversely, retraction ratio and swelling degree decreased when both plasticizers concentration increased. In conclusion, the sorbitol-plasticized film showed a potency to be developed as hard capsule material.

ENZYMATIC DETERMINATION OF STARCH IN DOCE DE LEITE USING DIALYSIS

Directory of Open Access Journals (Sweden)

DEMIATE Ivo Motim

2001-01-01

Full Text Available The importance of starch for the food industry makes it necessary to develop new, fast, economic and accurate methodologies for its quantification. In the present paper starch hydrolysis using commercial enzymes of industrial grade are studied aiming to develop an easy and cheap analysis, available to a greater number of industries and technicians. The proposed method is simple, divided in a first step where soluble sugars are eliminated from the samples by using dialysis, followed by starch hydrolysis of the retained fraction with a thermoresistent bacterial alfa-amylase (Termamyl 120L® and an amyloglucosidase (AMG 300L®. The hydrolysis conditions were those suggested by the enzyme producer. After the hydrolysis step the material was dialysed again for the extraction of glucose that was quantified by the glucose-oxidase colorimetric reactant. The results allowed the construction of calibration equations for starch determination on the analyzed samples. These samples were produced on a laboratory scale and native and acid-modified corn starches were added in known concentrations. By considering the final dilutions employed for glucose determination on the samples, it was possible to confirm that they were identical to that of the glucose-oxidase reactant calibration.

Improved Starch Digestion of Sucrase-deficient Shrews Treated With Oral Glucoamylase Enzyme Supplements.

Science.gov (United States)

Nichols, Buford L; Avery, Stephen E; Quezada-Calvillo, Roberto; Kilani, Shadi B; Lin, Amy Hui-Mei; Burrin, Douglas G; Hodges, Benjamin E; Chacko, Shaji K; Opekun, Antone R; Hindawy, Marwa El; Hamaker, Bruce R; Oda, Sen-Ichi

2017-08-01

Although named because of its sucrose hydrolytic activity, this mucosal enzyme plays a leading role in starch digestion because of its maltase and glucoamylase activities. Sucrase-deficient mutant shrews, Suncus murinus, were used as a model to investigate starch digestion in patients with congenital sucrase-isomaltase deficiency.Starch digestion is much more complex than sucrose digestion. Six enzyme activities, 2 α-amylases (Amy), and 4 mucosal α-glucosidases (maltases), including maltase-glucoamylase (Mgam) and sucrase-isomaltase (Si) subunit activities, are needed to digest starch to absorbable free glucose. Amy breaks down insoluble starch to soluble dextrins; mucosal Mgam and Si can either directly digest starch to glucose or convert the post-α-amylolytic dextrins to glucose. Starch digestion is reduced because of sucrase deficiency and oral glucoamylase enzyme supplement can correct the starch maldigestion. The aim of the present study was to measure glucogenesis in suc/suc shrews after feeding of starch and improvement of glucogenesis by oral glucoamylase supplements. Sucrase mutant (suc/suc) and heterozygous (+/suc) shrews were fed with C-enriched starch diets. Glucogenesis derived from starch was measured as blood C-glucose enrichment and oral recombinant C-terminal Mgam glucoamylase (M20) was supplemented to improve starch digestion. After feedings, suc/suc and +/suc shrews had different starch digestions as shown by blood glucose enrichment and the suc/suc had lower total glucose concentrations. Oral supplements of glucoamylase increased suc/suc total blood glucose and quantitative starch digestion to glucose. Sucrase deficiency, in this model of congenital sucrase-isomaltase deficiency, reduces blood glucose response to starch feeding. Supplementing the diet with oral recombinant glucoamylase significantly improved starch digestion in the sucrase-deficient shrew.

Preparation and characterization of bionanocomposite films based on potato starch/halloysite nanoclay.

Science.gov (United States)

Sadegh-Hassani, Fatemeh; Mohammadi Nafchi, Abdorreza

2014-06-01

In this research casting method was used to prepare potato starch based bio-nanocomposite films with halloysite nanoclay as the reinforcing materials. The composition included potato starch with 40% (w/w) of a mixture of sorbitol/glycerol (weight ratio of 3 to 1as plasticizer) with nanoclay (0-5% w/w). The films were dried under controlled conditions. Physicochemical properties such as solubility in water, water absorption capacity (WAC), water vapour permeability (WVP), oxygen permeability, and mechanical properties of the films were measured. Results showed that by increasing the concentration of nanoclay, mechanical properties of films were improved. Tensile strength was increased from 7.33 to 9.82MPa, and elongation at break decreased from 68.0 to 44.0%. Solubility in water decreased from 35 to 23%, and heat seal strength increased from 375 to 580N/m. Also incorporation of clay nanoparticles in the structure of biopolymer decreased permeability of the gaseous molecules. In summary, addition of halloysite nanoclay, improve the barrier and mechanical properties of potato starch films and this bionanocomposites have high potential to be used for food packaging purposes. Copyright © 2014 Elsevier B.V. All rights reserved.

Preliminary Study on the Synthesis of Phosphorylated Mung Bean Starch: The Effect of pH on the Physicochemical and Functional Properties

Directory of Open Access Journals (Sweden)

Illona Nathania

2017-11-01

Full Text Available Mung bean (Vigna radiate L. is a grain legume widely cultivated in tropical and sub-tropical regions. Mung bean seeds contain a significant amount of carbohydrate (63%-w/w and are easily digested compared to seeds from other legumes. Mung bean starch has the potential to be used as thickener or gelling agents in food industries. Certain functional properties of mung bean starch, however, still need to be improved. In this research, a preliminary study was performed to upgrade mung bean starch properties using phosphorylation reaction. In particular, the effect of starch suspension pH (6–10 on the functional properties of the modified products was investigated. Phosphorylation was carried out at 130 °C, for 2 h using sodium tripolyphosphate (STPP with an intake of 5%-w based on dry starch. The phosphorylated products were subsequently washed with water and dried. The experimental results show that the P-content of the phosphorylated mung bean starch is accessible in the range of 0.04–0.08%. The solubility (6.09–11.37%-w/w and swelling power (9.88–11.17 g/g of the modified starch products have been improved compared to native starch (solubility = 6.06 %-w/w, swelling power = 8.05 g/g. Phosphorylation also proved to increase peak viscosity, paste clarity, and water absorption/oil absorption capacity of the products.

Continuous-flow electro-assisted acid hydrolysis of granular potato starch via inductive methodology.

Science.gov (United States)

Li, Dandan; Yang, Na; Jin, Yamei; Guo, Lunan; Zhou, Yuyi; Xie, Zhengjun; Jin, Zhengyu; Xu, Xueming

2017-08-15

The induced electric field assisted hydrochloric acid (IEF-HCl) hydrolysis of potato starch was investigated in a fluidic system. The impact of various reaction parameters on the hydrolysis rate, including reactor number (1-4), salt type (KCl, MgCl 2 , FeCl 3 ), salt concentration (3-12%), temperature (40-55°C), and hydrolysis time (0-60h), were comprehensively assessed. Under optimal conditions, the maximum reducing sugar content in the hydrolysates was 10.59g/L. X-ray diffraction suggested that the crystallinity of IEF-HCl-modified starches increased with the intensification of hydrolysis but was lower than that of native starch. Scanning electron microscopy indicated that the surface and interior regions of starch granules were disrupted by the hydrolysis. The solubility of IEF-HCl-modified starches increased compared to native starch while their swelling power decreased, contributing to a decline in paste viscosity. These results suggest that IEF is a notable potential electrotechnology to conventional hydrolysis under mild conditions without any electrode touching the subject. Copyright © 2017 Elsevier Ltd. All rights reserved.

'The effect of inulin addition on structural and textural properties of extruded products under several extrusion conditions': The effect of inulin addition on structural and textural properties of rice flour extrudates.

Science.gov (United States)

Tsokolar-Tsikopoulos, Konstantinos C; Katsavou, Ioanna D; Krokida, Magdalini K

2015-10-01

The growing consumer demand for healthy snacks has turned the interest of industry and research in the development of new ready-to-eat products, enriched with dietary fibers. Inulin is a soluble fiber with a neutral taste that promotes the good function of the intestine. Rice flour extrudates were produced under various extrusion temperatures, screw speeds, feed moisture concentrations and inulin replacement levels. The objective of this study was to investigate the effect of the material characteristics and the extrusion conditions on the structural and textural properties of the extrudates. Simple mathematical models were used for properties correlation with process conditions and through regression analysis it was revealed that there is a significant effect of extrusion temperature, screw speed, feed moisture content and inulin concentration on the final properties. Both density and maximum stress increased when moisture content and inulin concentration increased, while they decreased when extrusion temperature and screw speed increased. These results were also strengthened by scanning electron microscopy. The highest expansion ratio was presented when decreasing all process conditions apart from screw speed.

Additional synthesis of starch from sucrose in leaves of arabidopsis in the light

International Nuclear Information System (INIS)

Keerberg, O.; Ivanova, H.; Keerberg, H.; Paernik, T.

2005-01-01

Full text: Accumulating during daytime starch is converted in the night into sucrose and consumed in respiratory, biosynthetic and transport processes. However in the light the degradation and conversion of starch are blocked. In pulse chase experiments with wild type plants and starchless mutants pgm or adg1 of arabidopsis an increase of starch radioactivity during chase in nonradioactive medium in the light was detected. These findings suggest that starch was additionally synthesized from labeled cytosolic soluble photosynthates, preferentially from sucrose. Radiogasometric studies of gas exchange have revealed that sucrose is consumed also in photorespiratory decarboxylations. To be involved in photorespiration the products of sucrose degradation must be transported from cytosol into chloroplast. We presume that derived from sucrose hexoses are transported into chloroplast by hexose transporter and phosphorylated there in hexokinase reaction. The phosphorylated hexoses may be consumed either for additional synthesis of starch or incorporated into the reductive pentose phosphate cycle and, via this cycle, into the glycolate cycle. (author)

Preparation and Characterization of Potentially Antimicrobial Polymer Films Containing Starch Nano- and Microparticles

Directory of Open Access Journals (Sweden)

Paulius Pavelas DANILOVAS

2014-09-01

Full Text Available The forming conditions of biodegradable polymer films containing iodine-modified starch particles as well as the properties of the obtained films were investigated. Cationic cross-linked starch microparticles and cationic starch nanoparticles were dispersed in cellulose acetate and hydroxyethyl cellulose solution, respectively, and composite films were spin-casted. The obtained films were characterized and their mechanical properties were assessed. The cellulose acetate solution has been found to be an appropriate matrix for the dispersion of dry modified starch microparticles, but not in the case of nanoparticles. Starch nanoparticles were obtained in an aqueous medium, and the mechanical properties of the formed cellulose acetate films are significantly reduced by water present in the casting solution. It has been estimated that a fairly high amount of nanoparticles (18 wt% can be immobilized into films of water-soluble hydroxyethyl cellulose without markedly affecting the mechanical properties of the films. DOI: http://dx.doi.org/10.5755/j01.ms.20.3.5426

Effects of acetic acid and lactic acid on physicochemical characteristics of native and cross-linked wheat starches.

Science.gov (United States)

Majzoobi, Mahsa; Beparva, Paniz

2014-03-15

The effects of two common organic acids; lactic and acetic acids (150 mg/kg) on physicochemical properties of native and cross-linked wheat starches were investigated prior and after gelatinization. These acids caused formation of some cracks and spots on the granules. The intrinsic viscosity of both starches decreased in the presence of the acids particularly after gelatinization. Water solubility increased while water absorption reduced after addition of the acids. The acids caused reduction in gelatinization temperature and enthalpy of gelatinization of both starches. The starch gels became softer, less cohesive, elastic and gummy when acids were added. These changes may indicate the degradation of the starch molecules by the acids. Cross-linked wheat starch was more resistant to the acids. However, both starches became more susceptible to the acids after gelatinization. The effect of lactic acid on physicochemical properties of both starches before and after gelatinization was greater than acetic acid. Copyright © 2013 Elsevier Ltd. All rights reserved.

Extruded plastic scintillator for MINERvA

International Nuclear Information System (INIS)

Pla-Dalmau, Anna; Bross, Alan D.; FermilabRykalin, Victor V.; Wood, Brian M.; NICADD, DeKalb

2005-01-01

An extrusion line has recently been installed at Fermilab in collaboration with NICADD (Northern Illinois Center for Accelerator and Detector Development). This new facility will serve to further develop and improve extruded plastic scintillator. Since polystyrene is widely used in the consumer industry, the logical path was to investigate the extrusion of commercial-grade polystyrene pellets with dopants to yield high quality plastic scintillator. The D0 and MINOS experiments are already using extruded scintillator strips in their detectors. A new experiment at Fermilab is pursuing the use of extruded plastic scintillator. A new plastic scintillator strip is being tested and its properties characterized. The initial results are presented here

The activity of barley alpha-amylase on starch granules is enhanced by fusion of a starch binding domain from Aspergillus niger glucoamylase

DEFF Research Database (Denmark)

Juge, N.; Nøhr, J.; Le Gal-Coëffet, M.-F.

2006-01-01

High affinity for starch granules of certain amylolytic enzymes is mediated by a separate starch binding domain (SBD). In Aspergillus niger glucoamylase (GA-I), a 70 amino acid O-glycosylated peptide linker connects SBD with the catalytic domain. A gene was constructed to encode barley alpha......-amylase 1 (AMY1) fused C-terminally to this SBD via a 37 residue GA-I linker segment. AMY1-SBD was expressed in A. niger, secreted using the AMY1 signal sequence at 25 mg x L(-1) and purified in 50% yield. AMY1-SBD contained 23% carbohydrate and consisted of correctly N-terminally processed multiple forms...... in A. niger). AMY1-SBD showed a 2-fold increased activity for soluble starch at low (0.5%) but not at high (1%) concentration. AMY1-SBD hydrolysed amylose DP440 with an increased degree of multiple attack of 3 compared to 1.9 for rAMY1. Remarkably, at low concentration (2 nM), AMY1-SBD hydrolysed...

Facile Synthesis of Curcumin-Loaded Starch-Maleate Nanoparticles

Directory of Open Access Journals (Sweden)

Suh Cem Pang

2014-01-01

Full Text Available We have demonstrated the loading of curcumin onto starch maleate (SM under mild conditions by mixing dissolved curcumin and SM nanoparticles separately in absolute ethanol and ethanol/aqueous (40 : 60 v/v, respectively. Curcumin-loaded starch-maleate (CurSM nanoparticles were subsequently precipitated from a homogeneous mixture of these solutions in absolute ethanol based on the solvent exchange method. TEM analysis indicated that the diameters of CurSM nanoparticles were ranged between 30 nm and 110 nm with a mean diameter of 50 nm. The curcumin loading capacity of SM as a function of loading duration was investigated using the UV-visible spectrophotometer. The loading of curcumin onto SM increased rapidly initially with loading duration, and the curcumin loading capacity of 15 mg/g was reached within 12 hours. CurSM nanoparticles exhibited substantially higher water solubility of 6.0 × 10−2 mg/mL which is about 300 times higher than that of pure curcumin. With enhanced water solubility and bioaccessibility of curcumin, the potential utility of CurSM nanoparticles in various biomedical applications is therefore envisaged.

Silver nanoparticles: a potential nanocatalyst for the rapid degradation of starch hydrolysis by α-amylase.

Science.gov (United States)

Ernest, Vinita; Shiny, P J; Mukherjee, Amitava; Chandrasekaran, N

2012-05-01

Silver nanoparticles (AgNPs) are proven to be an effective catalytic material for various applications due to their excellent optical and electronic properties. In this paper, we describe a novel approach for the degradation of starch using the catalytic behaviour of AgNPs in an enzyme catalysed reaction of starch hydrolysis by α-amylase. AgNPs were synthesized by soluble starch reducing silver nitrate to silver atoms. An increase of 4.7-fold in reducing sugar formation and 1.5 times faster enzyme activity confirmed the catalytic activity of AgNPs as a nanocatalyst. Surprisingly, starch degradation tests revealed that 9.9 mg of starch was hydrolysed within 5 min, which corroborates with the reducing sugar assay. In short, the present study paves way for the faster degradation of starch by immobilizing the enzyme onto the surface of the AgNP, which could be a promising application in the food industry. Copyright © 2012 Elsevier Ltd. All rights reserved.

Cultivar difference in physicochemical properties of starches and flours from temperate rice of Indian Himalayas.

Science.gov (United States)

Mir, Shabir Ahmad; Bosco, Sowriappan John Don

2014-08-15

Starch and flour of seven temperate rice cultivars grown in Himalayan region were evaluated for composition, granule structure, crystallinity, Raman spectrometry, turbidity, swelling power, solubility, pasting properties and textural properties. The rice cultivars showed medium to high amylose content for starch (24.69-32.76%) and flour (17.78-24.86%). SKAU-382 showed the highest amount of amylose (32.76%). Rice starch showed polyhedral granule shapes and differences in their mean granule size (2.3-6.5 μm) were noted among the samples. The starch and flour samples showed type A-pattern with strong reflection at 15, 18, and 23. Pasting profile and textural analysis of rice starch and flour showed that all the cultivars differences, probably due to variation in amylose content. The present study can be used for identifying differences between rice genotypes for starch and flour quality and could provide guidance to possible industries for their end use. Copyright © 2014 Elsevier Ltd. All rights reserved.

Expansion and functional properties of extruded snacks enriched with nutrition sources from food processing by-products.

Science.gov (United States)

Korkerd, Sopida; Wanlapa, Sorada; Puttanlek, Chureerat; Uttapap, Dudsadee; Rungsardthong, Vilai

2016-01-01

Rich sources of protein and dietary fiber from food processing by-products, defatted soybean meal, germinated brown rice meal, and mango peel fiber, were added to corn grit at 20 % (w/w) to produce fortified extruded snacks. Increase of total dietary fiber from 4.82 % (wb) to 5.92-17.80 % (wb) and protein from 5.03 % (wb) to 5.46-13.34 % were observed. The product indicated high expansion and good acceptance tested by sensory panels. There were 22.33-33.53 and 5.30-11.53 fold increase in the phenolics and antioxidant activity in the enriched snack products. The effects of feed moisture content, screw speed, and barrel temperature on expansion and nutritional properties of the extruded products were investigated by using response surface methodology. Regression equations describing the effect of each variable on the product responses were obtained. The snacks extruded with feed moisture 13-15 % (wb) and extrusion temperature at 160-180 °C indicated the products with high preference in terms of expansion ratio between insoluble dietary fiber and soluble dietary fiber balance. The results showed that the by-products could be successfully used for nutritional supplemented expanded snacks.

Effect of the acetylation process on native starches of yam (Dioscorea spp.

Directory of Open Access Journals (Sweden)

Jairo Salcedo Mendoza

2016-07-01

Full Text Available In Colombia, it is necessary to produce native and modified starches for the use of amylaceous raw materials of major socioeconomic importance. In this study, the effects of the acetylation process on structural, morphological and functional properties of native starches yam, Dioscorea spp. (D. alata and D. rotundata were evaluated. Chemical modification by esterification with acetic anhydride was performed at different reaction times, and morphological and structural changes were assessed using the following techniques: infrared spectroscopy (FTIR, X-ray diffraction and scanning electron microscopy (SEM. Acetylation produced slight changes in the granule morphology, and a decreased degree of crystallinity (DC associated with a slight increase in the amylose content was observed. The introduction of acetyl groups into the starch structure caused a decrease in the gelatinization temperature and an increased retro gradation tendency. The acetylated starches had low degrees of substitution (DS<0.2, meaning they can be used in the food industry, considering that they showed greater stability, greater water absorption capacity and better solubility than native starches.

Novel polymer blends with thermoplastic starch

Science.gov (United States)

Taghizadeh, Ata

A new class of polymers known as "bioplastics" has emerged and is expanding rapidly. This class consists of polymers that are either bio-based or biodegradable, or both. Among these, polysaccharides, namely starch, are of great interest for several reasons. By gelatinizing starch via plasticizers, it can be processed in the same way as thermoplastic polymers with conventional processing equipment. Hence, these bio-based and biodegradable plastics, with their low source and refinery costs, as well as relatively easy processability, have made them ideal candidates for incorporation into various current plastic products. Four different plasticizers have been chosen here for gelatinization of thermoplastic starch (TPS): glycerol, sorbitol, diglycerol and polyglycerol, with the latter two being used for the first time in such a process. Two methodological categories are used. The first involves a calorimetric method (Differential Scanning Calorimetry) as well as optical microscopy; these are "static" methods where no shear is applied A wide range of starch/water/plasticizer compositions were prepared to explore the gelatinization regime for each plasticizer. The onset and conclusion gelatinization temperatures for sorbitol and glycerol were found to be in the same vicinity, while diglycerol and polyglycerol showed significantly higher transition temperatures. The higher molecular weight and viscosity of polyglycerol allow this transition to occur at an even higher temperature than with diglycerol. This is due to the increase in molecular weight and viscosity of the two new plasticizers, as well as their significant decrease in water solubility. It is demonstrated that the water/plasticizer ratio has a pronounced effect on gelatinization temperatures. When plasticizer content was held constant and water content was increased, it was found that the gelatinization temperature decreased for all the plasticizers. Meanwhile, when the water content was held constant and the

Effects of replacing dietary starch with neutral detergent-soluble fibre on ruminal fermentation, microbial synthesis and populations of ruminal cellulolytic bacteria using the rumen simulation technique (RUSITEC).

Science.gov (United States)

Zhao, X H; Liu, C J; Liu, Y; Li, C Y; Yao, J H

2013-12-01

A rumen simulation technique (RUSITEC) apparatus with eight 800 ml fermenters was used to investigate the effects of replacing dietary starch with neutral detergent-soluble fibre (NDSF) by inclusion of sugar beet pulp in diets on ruminal fermentation, microbial synthesis and populations of ruminal cellulolytic bacteria. Experimental diets contained 12.7, 16.4, 20.1 or 23.8% NDSF substituted for starch on a dry matter basis. The experiment was conducted over two independent 15-day incubation periods with the last 8 days used for data collection. There was a tendency that 16.4% NDSF in the diet increased the apparent disappearance of organic matter (OM) and neutral detergent fibre (NDF). Increasing dietary NDSF level increased carboxymethylcellulase and xylanase activity in the solid fraction and apparent disappearance of acid detergent fibre (ADF) but reduced the 16S rDNA copy numbers of Ruminococcus albus in both liquid and solid fractions and R. flavefaciens in the solid fraction. The apparent disappearance of dietary nitrogen (N) was reduced by 29.6% with increased dietary NDSF. Substituting NDSF for starch appeared to increase the ratios of acetate/propionate and methane/volatile fatty acids (VFA) (mol/mol). Replacing dietary starch with NDSF reduced the daily production of ammonia-N and increased the growth of the solid-associated microbial pellets (SAM). Total microbial N flow and efficiency of microbial synthesis (EMS), expressed as g microbial N/kg OM fermented, tended to increase with increased dietary NDSF, but the numerical increase did not continue as dietary NDSF exceeded 20.1% of diet DM. Results suggested that substituting NDSF for starch up to 16.4% of diet DM increased digestion of nutrients (except for N) and microbial synthesis, and further increases (from 16.4% to 23.8%) in dietary NDSF did not repress microbial synthesis but did significantly reduce digestion of dietary N. © 2012 Blackwell Verlag GmbH.

Utilization of modified starch from avocado (Persea americana Mill.) seed in cream soup production

Science.gov (United States)

Cornelia, M.; Christianti, A.

2018-01-01

Avocado (Persea americana Mill.) seed was often seen as waste and underutilized resources, especially in the food industry. The aim of this research was to modify the structure of avocado seed starch using the cross-linking method, to improve the viscosity stability in the cream soup. In the preliminary research, starch was isolated from the seed and modified by STPP (sodium tripolyphosphate) with 2%, 4%, and 6% concentration and were reacted for 1, 2, and 3 hours. Starches were analyzed for moisture and ash content, paste clarity, gel strength, swelling power, solubility, yield, and degree of whiteness. Based on the analysis results, the best reaction time and STPP concentration was 6% at 1 hour reaction time. Native starch and the best-modified starch were applied in the cream soup and compared with commercial cream soup. Cream soups were analyzed for viscosity stability using viscometer in 0, 1, 3, and 5 hours after storage in room temperature. The result showed that cream soup using modified starch has better viscosity stability than native starch and commercial cream soup after 5 hours storage, which was 181.7 ± 4.85 cP. Sensory analysis showed that cream soup using modified starch was more acceptable than the others. Avocado seed modified starch has phosphate group that strengthen the starch chain to prevent viscosity breakdown.

Study on profile measurement of extruding tire tread by laser

Science.gov (United States)

Wang, LiangCai; Zhang, Wanping; Zhu, Weihu

1996-10-01

This paper presents a new 2D measuring system-profile measurement of extruding tire tread by laser. It includes the thickness measurement of extruding tire tread by laser and the width measurement of extruding tire tread using Moire Fringe. The system has been applied to process line of extruding tire tread. Two measuring results have been obtained. One is a standard profile picture of extruding tire tread including seven measuring values. Another one is a series of thickness and width values. When the scanning speed thickness range is thickness < +/- 0.1mm.

High-level ethanol production from starch by a flocculent Saccharomyces cerevisiae strain displaying cell-surface glucoamylase

Energy Technology Data Exchange (ETDEWEB)

Kondo, A.; Shigechi, H.; Abe, M.; Uyama, K. [Dept. of Chemical Science and Engineering, Kobe Univ., Nadaku, Kobe (Japan); Matsumoto, T.; Fukuda, H. [Div. of Molecular Science, Kobe Univ., Nadaku, Kobe (Japan); Takahashi, S.; Ueda, M.; Tanaka, A. [Dept. of Synthetic Chemistry and Biological Chemistry, Kyoto Univ., Sakyoku, Kyoto (Japan); Kishimoto, M. [Dept. of Biotechnology, Osaka Univ., Osaka (Japan)

2002-07-01

A Strain of host yeast YF207, which is a tryptophan auxotroph and shows strong flocculation ability, was obtained from Saccharomyces diastaticus ATCC60712 and S. cerevisiae W303-1B by tetrad analysis. The plasmid pGA11, which is a multicopy plasmid for cell-surface expression of the Rhyzopus oryzae glucoamylase/{alpha}-agglutinin fusion protein, was then introduced into this flocculent yeast strain (YF207/pGA11). Yeast YF207/pGA11 grew rapidly under aerobic condition (dissolved oxygen 2.0 ppm), using soluble starch. The harvested cells were used for batch fermentation of soluble starch to ethanol under anaerobic condition and showed high ethanol production rates (0.71 g h{sup -1} I{sup -1}) without a time lag, because glucoamylase was immobilized on the yeast cell surface. During repeated utilization of cells for fermentation, YF207/pGA11 maintained high ethanol production rates over 300 h. Moreover, in fed-batch fermentation with YF207/pGA11 for approximately 120 h, the ethanol concentration reached up to 50 g I{sup -1}. In conclusion, flocculent yeast cells displaying cell-surface glucoamylase are considered to be very effective for the direct fermentation of soluble starch to ethanol. (orig.)

Starch bioengineering

DEFF Research Database (Denmark)

Blennow, Andreas

2018-01-01

Application of starch in industry frequently requires extensive modification. This is usually achieved by chemical and/or physical modification that is time-consuming and often expensive and polluting. To impart functionality as early as possible in the starch production chain, modification can...... be achieved directly as part of the developing starch storage roots, tubers, and seeds and grains of the crop. Starch has been a strong driver for human development and is now the most important energy provider in the diet forcing the development of novel and valuable starch qualities for specific...... applications. Among the most important structures that can be targeted include starch phosphorylation chain transfer/branching generating chemically substituted and chain length-modified starches such as resistant and health-promoting high-amylose starch. Starch bioengineering has been employed for more than...

Characterization of edible films of Swartzia burchelli phosphated starches and development of coatings for post-harvest application to cherry tomatoes

Directory of Open Access Journals (Sweden)

Millene Aparecida Gomes

2016-08-01

Full Text Available The market demand for corn starch and cassava continues to increase because of their use in edible applications, their biodegradable nature, and other appealing properties. As a result, there is a need to identify alternative starch sources, for example, the seeds of S. burchelli, with the potential to be modified for use in post-harvest applications. Therefore, this study aimed to develop and characterize edible films based on the starch phosphates of the seeds of S. burchelli, with the specific aim to apply these starches to cherry tomatoes for post-harvest conservation. After extraction, the starch was phosphorylated with sodium tripolyphosphate (STP in different concentrations and times according to a 2 x 2 factorial design with additional treatment (native starch. After modification, the starch phosphates were selected for the preparation of edible films using glycerol as a plasticizer, in proportions of 5, 10, 15 and 20% for each selected starch. The films were measured for thickness, permeability to water vapor and solubility in water. According to their permeability values, 4 films were selected for application in the coverage of cherry tomatoes. The conservation of cherry tomatoes with and without coverage was studied over 8 evaluation times (up to 21 days at 10±2 °C and 80±5% relative humidity. The weight loss, soluble solids, titratable acidity, maturation index, and firmness were measured every 3 days during storage. The starch phosphates showed a phosphorus content within that established by standards, such that the resulting films are acceptable for use in food for human consumption. The edible films presented with an acceptable appearance and without the development of cracks. The concentration of glycerol and the type of starch influenced the characteristics of the films, increasing the permeability and reducing the water solubility of the various edible films. The best result obtained regarding the conservation of cherry

Physicochemical and tablet properties of Cyperus alulatus rhizomes starch granules.

Science.gov (United States)

Paramakrishnan, N; Jha, S; Kumar, K Jayaram

2015-05-01

The starch extracted from rhizomes of Cyperus alulatus (CA) was characterized for its physicochemical, morphological and tableting properties. Rhizomes of CA yield a significant quantity of starch granules (CASG) i.e., 11.93%. CASG was characterized in terms of moisture, ash and amylose contents, solubility and swelling power, paste clarity and water retention capacity. The swelling power was found to be significantly improved with the increase in temperature. Scanning electron micrographs revealed that the granule's surface was smooth, the granules were spherical, mostly round, disc like, and the size range was 6.65-12.13 μm. Finger print region in FTIR spectra confirmed its carbohydrate nature. The evaluated micromeritic properties of extracted granule's bulk density, tapped density, Carr's index, Hausner ratio, true density and porosity render unique practicability of CASG being used as an adjuvant in pharmaceutical solid dosage forms. Tablets prepared by using CASG showed higher mechanical strength and more disintegration time, which depicted the characteristic binding nature of the starch granules. As CASG is imparting better binding properties in less concentration and also it can be used in combination with the established starches to get the synergistic effect; this starch can be used commercially in the tablet preparation. Copyright © 2015 Elsevier B.V. All rights reserved.

Comparison of Structural and Functional Properties of Starches from the Rhizome and Bulbil of Chinese Yam (Dioscorea opposita Thunb.

Directory of Open Access Journals (Sweden)

Biao Zhang

2018-02-01

Full Text Available Chinese yam is an important edible starch plant and widely cultivated in China. Its rhizome and bulbil are starch storage tissues below and above ground, respectively. In this paper, starches were isolated from the rhizome and bulbil of Chinese yam, and their structural and functional properties were compared. Both starches had an oval shape with an eccentric hilum and a CA-type crystalline structure. Their short-range ordered structure and lamellar structure had no significant difference. However, the rhizome starch had a significantly bigger granule size and lower amylose content than the bulbil starch. The swelling power and water solubility were significantly lower in the rhizome starch than in the bulbil starch. The onset and peak gelatinization temperatures were significantly higher in the rhizome starch than in the bulbil starch. The rhizome starch had a significantly higher breakdown viscosity and a lower setback viscosity than the bulbil starch. The thermal stability was lower in the rhizome starch than in the bulbil starch. The rhizome starch had a significantly lower resistance to hydrolysis and in vitro digestion than the bulbil starch. The above results provide important information for the utilization of rhizome and bulbil starches of Chinese yam.

Characterization of films made with chayote tuber and potato starches blending with cellulose nanoparticles.

Science.gov (United States)

Aila-Suárez, Selene; Palma-Rodríguez, Heidi M; Rodríguez-Hernández, Adriana I; Hernández-Uribe, Juan P; Bello-Pérez, Luis A; Vargas-Torres, Apolonio

2013-10-15

The aim of this study was to characterize chayotextle starch films reinforced with cellulose (C) and cellulose nanoparticle (CN) (at concentrations of 0.3%, 0.5%, 0.8% and 1.2%), using thermal, mechanical, physicochemical, permeability, and water solubility tests. C was acid-treated to obtain CN. The films were prepared by casting; potato starch and C were used as the control. The solubility of the starch films decreased with the addition of C and CN compared with its respective film without C and CN. No statistical difference (α=0.05) was found in the films added with different concentrations of C and CN. In general, the mechanical properties were improved with the addition of C and CN, and higher values of tensile strength and elastic modulus were determined in the films reinforced with CN. The melting temperature and enthalpy increased with the addition of C and CN, and the values of both thermal parameters were higher in the films with CN than with C; the enthalpy value of the film decreased when the concentration of C or CN increased in the composite. Low concentration of C and CN is better distributed in the matrix film. The addition of C and CN in the starch films improved some mechanical, barrier, and functional properties. Copyright © 2013 Elsevier Ltd. All rights reserved.

Instant blend from cassava derivatives produced by extrusion

OpenAIRE

Trombini, Fernanda Rossi Moretti; Mischan, Martha Maria; Leonel, Magali

2016-01-01

ABSTRACT: The current research aimed to evaluate the effects of extrusion parameters on the physical characteristics of extruded blends of cassava leaf flour and starch. A factorial central composite design with four independent variables and the response surface methodology were used to evaluate the results of color parameters (L*, a*, b*), water absorption index, water solubility index and paste properties, according to the variations in the leaf flour percentage (1.5 to 7.5%), extrusion te...

Selected properties of biodegradable material produced from thermoplastic starch with by-products of food industry addition

Directory of Open Access Journals (Sweden)

Zdybel Ewa

2017-06-01

Full Text Available In this work extrusion process were used to create thermoplastic starch and to mix obtained starch with linen, quince and apple pomace at the same time. Obtained starch beads were formed in shapes. In experimental material was determined thermal conductivity, water absorption and the solubility in water. It is possible to get the biodegradable material produced from thermoplastic starch with an addition of fruit pomace. Adding pomace and glycerine to the biodegradable material made from starch change of susceptibility on water action. In the case of materials containing pomace, glycerine addition decreases the susceptibility on water action compared to the material manufactured with pomace addition but without glycerine. In the material containing pomace, glycerine addition caused the increase of the thermal insulation time compared to the material with pomace but no glycerine in it.

Starch films from a novel (Pachyrhizus ahipa) and conventional sources: Development and characterization

International Nuclear Information System (INIS)

López, Olivia V.; García, María A.

2012-01-01

Biodegradable films from ahipa, cassava and corn native starches were developed by casting method and their physicochemical, mechanical and barrier properties were analyzed taking into account the different starch botanical sources. Filmogenic suspensions were prepared; their rheological behaviors were studied and all of them exhibited film-forming ability. However, mechanical assays demonstrated that unplasticized films were too rigid, limiting their technological applications. Thus, 1.5% w/w of glycerol as plasticizer was added to filmogenic suspensions and film flexibility and extensibility were improved, this effect was more significant for ahipa and cassava starch films. Furthermore, thickness, moisture content and water solubility of the developed films were increased when plasticizer was incorporated. Glycerol addition reduced film water vapor permeability and the lowest reduction corresponded to cassava starch films due to the high viscosity of its filmogenic suspensions. Plasticized starch films resulted to be UV radiation barriers; ahipa starch films had the lowest light absorption capacity and higher transparency than cassava and corn starch films. Dynamic-mechanical analysis indicated that plasticized films were partially miscible systems exhibiting two relaxations, one attributed to the starch-rich phase and the other to the glycerol-rich one. Likewise, it could be demonstrated that glycerol exerted a major plasticizing effect on ahipa starch matrixes. Highlights: ► Ahipa, cassava and corn starch films were developed by casting method. ► Glycerol effect on film mechanical behavior was major for tuberous starch films. ► Ahipa starch films resulted to be more transparent with lower UV absorption capacity. ► Plasticized films were partially miscible systems: with a glycerol-rich and a starch-rich phase. ► Glycerol exerted a major plasticizing effect on ahipa starch films.

Biodegradable blends of starch/polyvinyl alcohol/glycerol: multivariate analysis of the mechanical properties

Directory of Open Access Journals (Sweden)

Juliano Zanela

Full Text Available Abstract The aim of the work was to study the mechanical properties of extruded starch/polyvinyl alcohol (PVA/glycerol biodegradable blends using multivariate analysis. The blends were produced as cylindrical strands by extrusion using PVAs with different hydrolysis degrees and viscosities, at two extrusion temperature profiles (90/170/170/170/170 °C and 90/170/200/200/200 °C and three conditioning relative humidities of the samples (33, 53, and 75%. The mechanical properties showed a great variability according to PVA type, as well as the extrusion temperature profile and the conditioning relative humidity; the tensile strength ranged from 0.42 to 5.40 MPa, elongation at break ranged from 10 to 404% and Young’s modulus ranged from 0.93 to 13.81 MPa. The multivariate analysis was a useful methodology to study the mechanical properties behavior of starch/PVA/glycerol blends, and it can be used as an exploratory technique to select of the more suitable PVA type and extrusion temperature to produce biodegradable materials.

Effect of gamma radiation on physico-chemical characteristics of red gram (Cajanus cajan) starch

International Nuclear Information System (INIS)

Nene, S.P.; Vakil, U.K.; Sreenivasan, A.

1975-01-01

Total reducing and nonreducing sugars in red gram (Cajanus cajan) are not affected by radiation treatment (1 Mrad). Oligosaccharides, reported as flatulence factors in legumes, namely stachyose and raffinose, are slightly decreased on cooking the irradiated samples. Irradiated and cooked red gram starch is more susceptible to alpha-amylase action than the unirradiated sample. Rheological properties of red gram starch, such as gelatinization viscosity, swelling power and solubility improve on irradiation resulting in a final cooked product with better textural properties. (U.S.)

Sugar uptake and starch biosynthesis by slices of developing maize endosperm

International Nuclear Information System (INIS)

Felker, F.C.; Liu, Kangchien; Shannon, J.C.

1990-01-01

14 C-Sugar uptake and incorporation into starch by slices of developing maize (Zea mays L.) endosperm were examined and compared with sugar uptake by maize endosperm-derived suspension cultures. Rates of sucrose, fructose, and D- and L-glucose uptake by slices were similar, whereas uptake rates for these sugars differed greatly in suspension cultures. Concentration dependence of sucrose, fructose, and D-glucose uptake was biphasic (consisting of linear plus saturable components) with suspension cultures but linear with slices. These and other differences suggest that endosperm slices are freely permeable to sugars. After diffusion into the slices, sugars were metabolized and incorporated into starch. Starch synthesis, but not sugar accumulation, was greatly reduced by 2.5 millimolar p-chloromercuribenzenesulfonic acid and 0.1 millimolar carbonyl cyanide m-chlorophenylhydrazone. Starch synthesis was dependent on kernel age and incubation temperature, but not on external pH (5 through 8). Competing sugars generally did not affect the distribution of 14 C among the soluble sugars extracted from endosperm slices incubated in 14 C-sugars. Competing hexoses reduced the incorporation of 14 C into starch, but competing sucrose did not, suggesting that sucrose is not a necessary intermediate in starch biosynthesis. The bidirectional permeability of endosperm slices to sugars makes the characterization of sugar transport into endosperm slices impossible, however the model system is useful for experiments dealing with starch biosynthesis which occurs in the metabolically active tissue

Effect of Hydroxypropylation on Functional Properties of Different Cultivars of Sweet Potato Starch in Sri Lanka

Directory of Open Access Journals (Sweden)

Suraji Senanayake

2014-01-01

Full Text Available Starches obtained from different cultivars of sweet potatoes commonly consumed in Sri Lanka, were chemically modified with hydroxypropyl substitution, to analyze the changes in the physicochemical properties. Significant changes (P<0.05 in the crude digestibility level, thermal properties, and the water separation (syneresis of starch gels (7.0% db during cold and frozen storage were observed due to the modification. Hydroxypropylation increased the gel stability, water solubility, digestibility, and storage stability of the native starches in the cold storage to a significant level. Lowered gelatinization and retrogradation enthalpies as well as gelatinization temperature were observed for derivatized starches compared to the native starch. Low levels of pasting stability with increased levels of breakdown and reduced cold paste viscosity were observed in the hydroxypropylated starch samples except for the Malaysian cultivar (S5. Chemically modified starch gels stored under cold storage did not show a syneresis for two weeks in the cycle and the frozen storage showed much improved stability in the starch gels within the four-week cycle. Chemical modification of sweet potato starch with hydroxyl propyl substitution can enhance the functional characteristics of the native starch which will improve its potential application in the food industry.

Impact of the Soak and the Malt on the Physicochemical Properties of the Sorghum Starches

Directory of Open Access Journals (Sweden)

Huiming Zhou

2010-08-01

Full Text Available Starches were isolated from soaked and malted sorghum and studied to understand their physicochemical and functional properties. The swelling power (SP and the water solubility index (WSI of both starches were nearly similar at temperatures below 50 °C, but at more than 50 °C, the starch isolated from malted sorghum showed lower SP and high WSI than those isolated from raw and soaked sorghum. The pasting properties of starches determined by rapid visco-analyzer (RVA showed that malted sorghum starch had a lower viscosity peak value (86 BU/RVU than raw sorghum starch (454 BU/RVU. For both sorghum, X-ray diffractograms exhibited an A-type diffraction pattern, typical of cereal starches and the relative degrees of crystallinity ranged from 9.62 to 15.50%. Differential scanning calorimetry (DSC revealed that raw sorghum starch showed an endotherm with a peak temperature (Tp at 78.06 °C and gelatinization enthalpies of 2.83 J/g whereas five-day malted sorghum starch had a Tp at 47.22 °C and gelatinization enthalpies of 2.06 J/g. Storage modulus (G′ and loss modulus (G″ of all starch suspensions increased steeply to a maximum at 70 °C and then decreased with continuous heating. The structural analysis of malted sorghum starch showed porosity on the granule’s surface susceptible to the amylolysis. The results showed that physicochemical and functional properties of sorghum starches are influenced by soaking and malting methods.

The extrudate swell of HDPE: Rheological effects

Science.gov (United States)

Konaganti, Vinod Kumar; Ansari, Mahmoud; Mitsoulis, Evan; Hatzikiriakos, Savvas G.

2017-05-01

The extrudate swell of an industrial grade high molecular weight high-density polyethylene (HDPE) in capillary dies is studied experimentally and numerically using the integral K-BKZ constitutive model. The non-linear viscoelastic flow properties of the polymer resin are studied for a broad range of large step shear strains and high shear rates using the cone partitioned plate (CPP) geometry of the stress/strain controlled rotational rheometer. This allowed the determination of the rheological parameters accurately, in particular the damping function, which is proven to be the most important in simulating transient flows such as extrudate swell. A series of simulations performed using the integral K-BKZ Wagner model with different values of the Wagner exponent n, ranging from n=0.15 to 0.5, demonstrates that the extrudate swell predictions are extremely sensitive to the Wagner damping function exponent. Using the correct n-value resulted in extrudate swell predictions that are in excellent agreement with experimental measurements.

Apically-extruded debris using the ProTaper system.

Science.gov (United States)

Azar, Nasim Gheshlaghi; Ebrahimi, Gholamreza

2005-04-01

The purpose of this in vitro study was to determine the quantity of debris and irrigant extruded apically using the ProTaper system compared to ProFiles and K-Flexofiles. Thirty-six mesio-buccal root canals of human mandibular molars were selected and divided into three groups of twelve canals. Two groups were instrumented with ProFiles and ProTapers according to the manufacturer's instructions. The other group was instrumented with K-Flexofiles using the step-back technique. A standard amount of irrigant was used for each canal. Apically-extruded debris and irrigant was collected in pre-weighed vials. The mean weight of extruded debris and irrigant for each group was statistically analysed using Student's t-test and one-way ANOVA. All instrumentation techniques produced extruded debris and irrigant. Although the mean amount of extrusion with the step-back technique was higher than the two rotary systems, there was no significant difference between the three groups (p > 0.05). NiTi rotary systems were associated with less apical extrusion, but were not significantly better than hand file instrumentation. All techniques extruded debris.

The adsorption of α-amylase on barley proteins affects the in vitro digestion of starch in barley flour.

Science.gov (United States)

Yu, Wenwen; Zou, Wei; Dhital, Sushil; Wu, Peng; Gidley, Michael J; Fox, Glen P; Gilbert, Robert G

2018-02-15

The conversion of barley starch to sugars is a complex enzymic process. Most previous work concerned the biotechnical aspect of in situ barley enzymes. However, the interactions among the macromolecular substrates and their effects on enzymic catalysis has been little examined. Here, we explore the mechanisms whereby interactions of protein and starch in barley flour affect the kinetics of enzymatic hydrolysis of starch in an in vitro system, using digestion rate data and structural analysis by confocal microscopy. The degradation kinetics of both uncooked barley flour and of purified starches are found to be two-step sequential processes. Barley proteins, especially the water-soluble component, are found to retard the digestion of starch degraded by α-amylase: the enzyme binds with water-insoluble protein and with starch granules, leading to reduced starch hydrolysis. These findings are of potential industrial value in both the brewing and food industries. Copyright © 2017 Elsevier Ltd. All rights reserved.

Influence of extruder screws speed and process temperature on the extrudate shape changes of the maize-spelt blends

Directory of Open Access Journals (Sweden)

Tomasz Żelaziński

2018-01-01

Full Text Available The objective of the study was examination of changes in the shape factors of extruded products, which occur as a result of different settings of the extrusion process variables. Samples analysed included products created by means of the extrusion process from a mixture of spelt flour and cornmeal, with the share of spelt at 70 to 100%. The samples were made with the use of a co-rotating twin screw extruder. Two speeds of extruder screw rotation (300 and 350 rpm as well as two levels of temperature (120 and 140°C were set during the investigation. The samples obtained were photographed in a light box, following which they underwent an image analysis with the use of specialist vision software. Four shape-related factors were determined: area, elongation factor, Heywood circularity factor and compactness factor. It was determined that the product shape changed significantly depending on the share of spelt flour in the mixture. Moreover, it was observed that change in the screw rotation speed within the analysed range may cause material changes in the shape of particular extrudates.

Impact of acid and oxidative modifications, single or dual, of sorghum starch on biodegradable films.

Science.gov (United States)

Biduski, Bárbara; Silva, Francine Tavares da; Silva, Wyller Max da; Halal, Shanise Lisie de Mello El; Pinto, Vania Zanella; Dias, Alvaro Renato Guerra; Zavareze, Elessandra da Rosa

2017-01-01

The objective of this study was to evaluate the effects of acid and oxidation modifications on sorghum starch, as well as the effect of dual modification of starch on the physical, morphological, mechanical, and barrier properties of biodegradable films. The acid modification was performed with 3% lactic acid and the oxidation was performed with 1.5% active chlorine. For dual modification, the acid modification was performed first, followed by oxidation under the same conditions as above. Both films of the oxidized starches, single and dual, had increased stiffness, providing a higher tensile strength and lower elongation when compared to films based on native and single acid modified starches. However, the dual modification increased the water vapor permeability of the films without changing their solubility. The increase in sorghum starch concentration in the filmogenic solution increased the thickness, water vapor permeability, and elongation of the films. Copyright © 2016. Published by Elsevier Ltd.

Modified Starch-Chitosan Edible Films: Physicochemical and Mechanical Characterization

Directory of Open Access Journals (Sweden)

Monserrat Escamilla-García

2017-12-01

Full Text Available Starch and chitosan are widely used for preparation of edible films that are of great interest in food preservation. This work was aimed to analyze the relationship between structural and physical properties of edible films based on a mixture of chitosan and modified starches. In addition, films were tested for antimicrobial activity against Listeria innocua. Films were prepared by the casting method using chitosan (CT, waxy (WS, oxidized (OS and acetylated (AS corn starches and their mixtures. The CT-starches films showed improved barrier and mechanical properties as compared with those made from individual components, CT-OS film presented the lowest thickness (74 ± 7 µm, water content (11.53% ± 0.85%, w/w, solubility (26.77% ± 1.40%, w/v and water vapor permeability ((1.18 ± 0.48 × 10−9 g·s−1·m−1·Pa−1. This film showed low hardness (2.30 ± 0.19 MPa, low surface roughness (Rq = 3.20 ± 0.41 nm and was the most elastic (Young’s modulus = 0.11 ± 0.06 GPa. In addition, films made from CT-starches mixtures reduced CT antimicrobial activity against L. innocua, depending on the type of modified starch. This was attributed to interactions between acetyl groups of AS with the carbonyl and amino groups of CT, leaving CT with less positive charge. Interaction of the pyranose ring of OS with CT led to increased OH groups that upon interaction with amino groups, decreased the positive charge of CT, and this effect is responsible for the reduced antimicrobial activity. It was found that the type of starch modification influenced interactions with chitosan, leading to different films properties.

Effects of tempering (annealing), acid hydrolysis, low-citric acid substitution on chemical and physicochemical properties of starches of four yam (Dioscorea spp.) cultivars.

Science.gov (United States)

Falade, Kolawole O; Ayetigbo, Oluwatoyin E

2017-05-01

The effects of tempering (annealing), acid hydrolysis and low-citric acid substitution on chemical and physicochemical properties of starches of four Nigerian yam cultivars were investigated. Crude fat and protein contents of the native starches decreased significantly after the modifications, while nitrogen-free extract increased significantly with acid hydrolysis and citric acid substitution. Acid hydrolysis and low-citric acid substitution reduced the least concentration for gel formation of the starches from 4 to 2% w/v, but tempering had no effect. Swelling power of the starches reduced significantly, and water solubility increased significantly at 75 and 85 °C, especially with acid hydrolysis and low-citric acid substitution. However, tempering significantly reduced starch solubility in the four cultivars. Paste clarity of starches of white (29.17%), water (18.90%), yellow (30.90%) and bitter (10.57%) yams reduced significantly with tempering to 14.43, 11.83, 16.93 and 7.27%, but increased significantly with acid hydrolysis to 41.40, 35.37, 28.77 and 32.33%, and low-citric acid substitution to 36.60, 44.17, 50.67 and 14.33%, respectively. Pasting properties such as peak, trough, breakdown, final, and setback viscosities and peak time of native starches reduced significantly with acid hydrolysis and low-citric acid substitution, however, tempering significantly increased their pasting temperature, peak time, setback and final viscosities.

Optimization and Numerical Simulation of Outlet of Twin Screw Extruder

Directory of Open Access Journals (Sweden)

Zhang Yuan

2018-01-01

Full Text Available In view of the unreasonable design of non-intermeshing counter-rotating twin screw extruder die, the problem of productivity reduction was discussed. Firstly, the mathematical model of extruder productivity was established. The extruder die model was improved. Secondly, the force analysis of twin screw extruder physical model was carried out. Meanwhile, A combination of mechanical analysis and numerical simulation was adopted. The velocity field, pressure field and viscosity field were calculated by Mini-Element interpolation method, linear interpolation method and Picard iterative convergence method respectively. The influence of die model on the quantity of each field before and after improvement was analyzed. The results show that the improved model had increased the rheological parameters of the flow field, the leakage and reverse flow decreased. Through post-processing calculation, the productivity of the third dies extruder was 10% higher than before. The research results provide a theoretical basis for the design and optimization of die model of non intermeshing counter-rotating twin screw extruder.

In vitro utilization of amylopectin and high-amylose maize (Amylomaize) starch granules by human colonic bacteria.

Science.gov (United States)

Wang, X; Conway, P L; Brown, I L; Evans, A J

1999-11-01

It has been well established that a certain amount of ingested starch can escape digestion in the human small intestine and consequently enters the large intestine, where it may serve as a carbon source for bacterial fermentation. Thirty-eight types of human colonic bacteria were screened for their capacity to utilize soluble starch, gelatinized amylopectin maize starch, and high-amylose maize starch granules by measuring the clear zones on starch agar plates. The six cultures which produced clear zones on amylopectin maize starch- containing plates were selected for further studies for utilization of amylopectin maize starch and high-amylose maize starch granules A (amylose; Sigma) and B (Culture Pro 958N). Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) was used to detect bacterial starch-degrading enzymes. It was demonstrated that Bifidobacterium spp., Bacteroides spp., Fusobacterium spp., and strains of Eubacterium, Clostridium, Streptococcus, and Propionibacterium could hydrolyze the gelatinized amylopectin maize starch, while only Bifidobacterium spp. and Clostridium butyricum could efficiently utilize high-amylose maize starch granules. In fact, C. butyricum and Bifidobacterium spp. had higher specific growth rates in the autoclaved medium containing high-amylose maize starch granules and hydrolyzed 80 and 40% of the amylose, respectively. Starch-degrading enzymes were cell bound on Bifidobacterium and Bacteroides cells and were extracellular for C. butyricum. Active staining for starch-degrading enzymes on SDS-PAGE gels showed that the Bifidobacterium cells produced several starch-degrading enzymes with high relative molecular (M(r)) weights (>160,000), medium-sized relative molecular weights (>66,000), and low relative molecular weights (spp. and C. butyricum degraded and utilized granules of amylomaize starch.

Impact of heat-moisture and annealing treatments on physicochemical properties and digestibility of starches from different colored sweet potato varieties.

Science.gov (United States)

Trung, Phan Thanh Bao; Ngoc, Luu Bui Bao; Hoa, Phan Ngoc; Tien, Nguyen Ngoc Thanh; Hung, Pham Van

2017-12-01

The objective of this study is to investigate the change in physicochemical properties and digestibility of starches isolated from colored sweet potato varieties under heat-moisture treatment (HMT) or annealing treatment (ANN). The results showed that morphology and X-ray diffraction patterns of the sweet potato starches remained unchanged after the HMT or ANN. The HMT significantly reduced peak viscosity, breakdown and setback and significantly increased pasting temperature, trough and final viscosities of the sweet potato starches. The swelling powers and solubility of the heat-moisture treated starches were significantly lower than those of the native or annealed starches. The decreased rapid digestible starch and the increased slowly digestible and resistant starch contents of the sweet potato starches after HMT or ANN as compared to those of the native starches were observed. The resistant starch (RS) contents of the heat-moisture treated sweet potato starches were in a range of 30.6-39.3%, significantly higher than those of the annealed starches (28.8-32.0%). The strong impact of the HMT on physicochemical properties and RS formation of the sweet potato starches compared to the ANN might be due to the high stability of the occurred interactions between starch molecules and amylopectin chains during treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

On the use of differential solubility in aqueous ethanol solutions to narrow the DP range of food-grade starch hydrolysis products.

Science.gov (United States)

Balto, Amy S; Lapis, Trina J; Silver, Rachel K; Ferreira, Andrew J; Beaudry, Christopher M; Lim, Juyun; Penner, Michael H

2016-04-15

Considerable research is focused on understanding the functionality of starch hydrolysis products (SHP) consisting of glucose, maltose, maltooligosaccharides (MOS), and maltopolysaccharides (MPS). A confounding factor in this research is the high molecular dispersity of commercially available SHP. The study presented herein characterizes a flexible fractionation approach for lowering the dispersity of such products. This was accomplished by fractionating a corn syrup solids (CSS) preparation based on the differential solubility of its component saccharides in aqueous-ethanol solutions. Products obtained from selected fractionations were characterized with respect to degree of polymerization (DP; liquid chromatography), dextrose equivalency (reducing sugar assays), and prevalence of branching (NMR). Glucose and maltose were preferentially removed from CSS using high (⩾90%) ethanol extractants. Preparations with relatively narrow ranges of MOS, lower DP MPS, and higher DP MPS were obtained through repetitive 70%-ethanol extractions. Linear, as opposed to branched, MOS and MPS were preferentially extracted under all conditions tested. Copyright © 2015 Elsevier Ltd. All rights reserved.

Investigation of process and product parameters for physicochemical properties of rice and mung bean (Vigna radiata) flour based extruded snacks.

Science.gov (United States)

Sharma, Chetan; Singh, Baljit; Hussain, Syed Zameer; Sharma, Savita

2017-05-01

PR 106 and SML 668 cultivars of rice and mung bean respectively, were studied for their potential to serve as a nutritious snack with improved protein quality and quantity. The effect of extrusion conditions, including feed moisture content (14-18%), screw speed (400-550 rpm) and barrel temperature (130-170°C) on the physicochemical properties (bulk density, water absorption index (WAI), water solubility index (WSI) and hardness) was investigated. The replacement of rice flour at 30% level with mung bean flour for making extruded snacks was evaluated. Pasting temperature increased (84-93 °C) while peak viscosity (2768-408 cP), hold viscosity (2018-369 cP), breakdown (750-39 cP), setback (2697-622 cP) and final viscosity (4715-991 cP) decreased with increasing mung bean flour addition. Increasing feed moisture lowered the specific mechanical energy (SME), WAI and WSI of extrudates whereas increased bulk density and hardness. Higher screw speed had linear positive effect on SME of extruder and negative linear effect on WAI. Positive curvilinear quadratic effect of screw speed was also observed on WSI and density. Higher barrel temperature linearly decreased the SME, density and hardness of extrudates. Developed extrusion cooked rice-mung bean snacks with increased protein content and improved protein quality along with higher dietary fibre and minerals have good potential in effectively delivering the nutrition to the population.

Effect of starch isolation method on properties of sweet potato starch

Directory of Open Access Journals (Sweden)

A. SURENDRA BABU

2014-08-01

Full Text Available Isolation method of starch with different agents influences starch properties, which provide attention for studying the most appropriate method for isolation of starch. In the present study sweet potato starch was isolated by Sodium metabisulphate (M1, Sodium chloride (M2, and Distilled water (M3 methods and these were assessed for functional, chemical, pasting and structural properties. M3 yielded the greatest recovery of starch (10.20%. Isolation methods significantly changed swelling power and pasting properties but starches exhibited similar chemical properties. Sweet potato starches possessed C-type diffraction pattern. Small size granules of 2.90 μm were noticed in SEM of M3 starch. A high degree positive correlation was found between ash, amylose, and total starch content. The study concluded that isolation methods brought changes in yield, pasting and structural properties of sweet potato starch.

Physicochemical, structural and thermal properties of oxidized, acetylated and dual-modified common bean (Phaseolus vulgaris L. starch

Directory of Open Access Journals (Sweden)

José Pedro WOJEICCHOWSKI

2018-03-01

Full Text Available Abstract Common beans are rich in protein and complex carbohydrates that are valuable for the human diet. Starch is the most abundant individual component; however, in its native form it has limited applications and modifications are necessary to overcome technological restrictions. The aim of this study was to evaluate the influence of oxidation, acetylation and dual-modification (oxidation-acetylation on the physicochemical, structural and thermal properties of common bean starch. The degree of substitution of the acetylated starches was compatible with food use. Fourier transform infrared spectra confirmed the acetylation of the bean starch, with a peak at 1,735cm-1. The granules of the bean starch were oval to spherical in shape, with no differences between the native and modified samples. Typical C-type diffraction of legume starches was found. The modified samples showed a reduced relative crystallinity and lower enthalpy change of gelatinization. The oxidized starch showed the highest peak viscosity, hardness, and gel adhesiveness due to the presence of functional groups. An increase in solubility and swelling power was observed, and the oxidized-acetylated starch presented the highest values. The properties of the modified bean starches made them suitable for application in breaded/battered foods, mainly due to improved textural attributes.

Effect of Gamma Irradiation on the Physicochemical and Functional Properties of Cassava Starch

International Nuclear Information System (INIS)

Asare, I.K.

2011-10-01

Cassava (Manihot esculanta Crantz) is popularly consumed as a staple food crop in many tropical countries in Africa, South America and Asia. In Africa the crop has been recognized as more than a subsistence crop. The crop is very important and commercially serves as a raw material for industries with significant effect on the economy of a country. Cassava roots contain high starch content and approximately half of the total roots produced is used for the production of starch for industrial purposes. Limitation to utilization of cassava roots by processors is due to its high perishability and bulkness, while native starches are structurally too weak and funtionally restricted for a wide variety of industrial applications. The objective of the project was to determine the effect of gamma irradiation as a modifying agent on native starch from three cassava varieties namely Ankra, Bosome nsia and TME419. Gamma radiation doses applied ranged between 0 - 20kGy and changes in physicochemical, functional and pasting indices of the starch were measured. Physicochemical indices measured were moisture content, amylose content, carbohydrate content, pH, ash content, fat content, protein content and L*a*b* values. Functional indices mesured were water absorption capacity, solubility index, bulk density, swelling power, fat absorption capacity, emulsion capacity, emulsion stability and least gelation concentration. Pasting indices measured were gelatinzation temperature, peak viscosity, viscosity at 92 degrees C and 50 degrees C, breakdown viscosity and setback viscosity. The pH, amylose content, carbohydrate content and ash content of native starch from Ankra, Bosome nsia and TME 419 were respectively 8.06, 7.80 and 7.18, 17.62%, 19.46% and 23.54%, 56.11%, 52.43% and 35.70%, 0.11%, 0.19% and 0.12%. The water absortion capacity and least gelation concentration of native starch from Ankra, Bosome nsia and TME 419 were 12.3%, 13.0% and 10.0%, respectively, least gelation

Biochemical Aspects of Non-Starch Polysaccharides

Directory of Open Access Journals (Sweden)

Rodica Căpriţă

2010-05-01

Full Text Available Polysaccharides are macromolecules of monosaccharides linked by glycosidic bonds. Non-starch polysaccharides (NSP are principally non-α-glucan polysaccharides of the plant cell wall. They are a heterogeneous group of polysaccharides with varying degrees of water solubility, size, and structure. The water insoluble fiber fraction include cellulose, galactomannans, xylans, xyloglucans, and lignin, while the water-soluble fibers are the pectins, arabinogalactans, arabinoxylans, and β-(1,3(1,4-D-glucans (β-glucans. Knowledge of the chemical structure of NSP has permitted the development of enzyme technology to overcome their antinutritional effects. The physiological effects of NSP on the digestion and absorption of nutrients in human and monogastric animals have been attributed to their physicochemical properties: hydration properties, viscosity, cation exchange capacity and organic compound absorptive properties. This paper reviews and presents information on NSPs chemistry, physicochemical properties and physiological effects on the nutrient entrapment.

UASB Treatment of Methanolic Pulp Wastewater with Addition of Waste Starch and Incinerated Ash

Science.gov (United States)

Takahashi, Shintaro; Kobaysashi, Takuro; Li, Yu-You; Harada, Hideki

The pulp wastewater consists mainly of methanol. It is expected to treat using upflow anaerobic sludge blanket (UASB) process. Paper manufactories also produce waste starch and incinerated ash. The integrated treating for these wastes is desirable. In this study, two UASB reactors were operated to treat pulp wastewater with addition of waste starch and with addition of incinerated ash, receptively. Continuous operations of a UASB reactor treating pulp wastewater with addition of waste starch (PS reactor) and a UASB reactor treating pulp wastewater with addition of incinerated ash (PA reactor) , were investigated at mesophilic conditions. The PS reactor performed well with an average 93.7% total CODCr and 97.3% soluble CODCr removal efficiency in average at a maximum volumetric loading rate (VLR) of 16.0 kgCOD/m3/d. The PA reactor was also successfully operated with an average 95.3% total CODCr and 97.5% soluble CODCr removal efficiency in average at a maximum VLR of 14.6 kgCOD/m3/d. Successfully developed granules were obtained after over 140 days of operation in both reactors, and the granules were 1 to 2 mm in mean diameter. Microbial analysis revealed the genus Methanomethylovorans was predominant in the granules of both reactors.

Nutritive value of wet distillers' solubles for pigs

Directory of Open Access Journals (Sweden)

Jarmo Valaja

1995-01-01

Full Text Available Digestibility and nitrogen (N metabolism were studied to evaluate the nutritive value of wet barley distillers’ solubles (DSB from an integrated starch-ethanol process for pigs. Eight castrated male pigs (live weight 72-103 kg were used in a 8 x 3 cyclic change-over design, where the diets were arranged factorially 2x2. The corresponding factors were the protein source (DSB or soya bean meal (SBM and the protein level (131 or 162 g crude protein (CP/kg dry matter (DM. Faeces and urine were collected in total. The four diets comprised barley, barley starch, minerals and vitamins with either DSB or SBM as the main source of protein. The digestibility of CP(p

Syneresis and chemical characteristics of fermented rice extract with probiotic bacteria and waxy maize starch

Directory of Open Access Journals (Sweden)

Kassia Kiss Firmino Dourado COSTA

2017-09-01

Full Text Available Abstract The objective of this work was to elaborate fermented extracts using rice bran and broken rice grains (proportion 8:92 with probiotic bacteria and different concentrations of waxy maize starch (WMS in order to obtain products with low level of syneresis and desirable physical-chemical characteristics, and to evaluate the content of phenolic compounds, antioxidant capacity and chemical composition of the extract selected and flavored with strawberry aroma and strawberry syrup. A randomized design was used with five treatments (0, 4, 8, 12 and 16 g 100 g–1 of WMS and four replications. The fermented rice extract had increased soluble solids (from 12.97 to 14.23 °Brix and total acidity (from 0.29 to 0.30 g 100 g–1, whereas total soluble sugars (from 9.24 to 8.73 g 100 g–1 and syneresis (from 10.16 to 0.99 g 100 g–1 decreased with gradual increments of waxy maize starch. The fermented rice extract containing 12 g 100 g–1 WMS reduced the syneresis by 89% compared to the control without waxy maize starch. The fermented rice extract with 12 g 100 g-1 of waxy maize starch flavored with strawberry aroma and strawberry syrup shows high nutritional value, antioxidant capacity, content of total phenolic compounds, and marketing potential, particularly for consumers with special needs, such as those allergic to lactose or soybean proteins, as an alternative food ready for consumption.

Physical and structural characterisation of starch/polyester blends with tartaric acid

International Nuclear Information System (INIS)

Olivato, J.B.; Müller, C.M.O.; Carvalho, G.M.; Yamashita, F.; Grossmann, M.V.E.

2014-01-01

Starch/PBAT blends were produced by reactive extrusion with tartaric acid (TA) as an additive. The effects of TA, glycerol and starch + PBAT on the mechanical, optical and structural properties of the films were evaluated, with formulations based in a constrained mixture design. Tartaric acid acts as a compatibiliser and promotes the acid hydrolysis of starch chains. These two functions explain the observed film resistance and opacity. TA reduced the weight loss in water. Scanning electron microscopy (SEM) images showed that TA reduces the interfacial tension between the polymeric phases, resulting in more homogeneous films. Nuclear magnetic resonance ( 13 C CPMAS) and Fourier transform infrared spectroscopy (FT-IR) suggest that tartaric acid is able to react with the hydroxyl groups of the starch by esterification/transesterification reactions, confirming its role as a compatibiliser. The addition of TA results in materials with better properties that are suitable for use in food packaging. - Highlights: • Tartaric acid (TA) was efficient as compatibiliser of starch/PBAT blends. • Film properties were analysed based on the modelling of the mixture design. • Greater proportions of TA resulted in more opaque and less soluble materials. • Esterification reactions promoted by TA were characterised by FT-IR and 13 C CPMAS NMR. • Compatibilised blends with TA showed better morphological and mechanical properties

Physical and structural characterisation of starch/polyester blends with tartaric acid

Energy Technology Data Exchange (ETDEWEB)

Olivato, J.B., E-mail: jubonametti@uel.br [Departamento de Ciência e Tecnologia de Alimentos, Centro de Ciências Agrárias, Universidade Estadual de Londrina, PO Box 6001, 86051-980 Londrina, PR (Brazil); Müller, C.M.O. [Departamento de Ciência e Tecnologia de Alimentos, Centro de Ciências Agrárias, Universidade Estadual de Londrina, PO Box 6001, 86051-980 Londrina, PR (Brazil); Carvalho, G.M. [Departamento de Química, Centro de Ciências Exatas, Universidade Estadual de Londrina, PO Box 6001, 86051-980 Londrina, PR (Brazil); Yamashita, F.; Grossmann, M.V.E. [Departamento de Ciência e Tecnologia de Alimentos, Centro de Ciências Agrárias, Universidade Estadual de Londrina, PO Box 6001, 86051-980 Londrina, PR (Brazil)

2014-06-01

Starch/PBAT blends were produced by reactive extrusion with tartaric acid (TA) as an additive. The effects of TA, glycerol and starch + PBAT on the mechanical, optical and structural properties of the films were evaluated, with formulations based in a constrained mixture design. Tartaric acid acts as a compatibiliser and promotes the acid hydrolysis of starch chains. These two functions explain the observed film resistance and opacity. TA reduced the weight loss in water. Scanning electron microscopy (SEM) images showed that TA reduces the interfacial tension between the polymeric phases, resulting in more homogeneous films. Nuclear magnetic resonance ({sup 13}C CPMAS) and Fourier transform infrared spectroscopy (FT-IR) suggest that tartaric acid is able to react with the hydroxyl groups of the starch by esterification/transesterification reactions, confirming its role as a compatibiliser. The addition of TA results in materials with better properties that are suitable for use in food packaging. - Highlights: • Tartaric acid (TA) was efficient as compatibiliser of starch/PBAT blends. • Film properties were analysed based on the modelling of the mixture design. • Greater proportions of TA resulted in more opaque and less soluble materials. • Esterification reactions promoted by TA were characterised by FT-IR and {sup 13}C CPMAS NMR. • Compatibilised blends with TA showed better morphological and mechanical properties.

Multiple Roles of Soluble Sugars in the Establishment of Gunnera-Nostoc Endosymbiosis1[OA

Science.gov (United States)

Khamar, Hima J.; Breathwaite, Erick K.; Prasse, Christine E.; Fraley, Elizabeth R.; Secor, Craig R.; Chibane, Fairouz L.; Elhai, Jeff; Chiu, Wan-Ling

2010-01-01

Gunnera plants have the unique ability to form endosymbioses with N2-fixing cyanobacteria, primarily Nostoc. Cyanobacteria enter Gunnera through transiently active mucilage-secreting glands on stems. We took advantage of the nitrogen (N)-limitation-induced gland development in Gunnera manicata to identify factors that may enable plant tissue to attract and maintain cyanobacteria colonies. Cortical cells in stems of N-stressed Gunnera plants were found to accumulate a copious amount of starch, while starch in the neighboring mature glands was nearly undetectable. Instead, mature glands accumulated millimolar concentrations of glucose (Glc) and fructose (Fru). Successful colonization by Nostoc drastically reduced sugar accumulation in the surrounding tissue. Consistent with the abundance of Glc and Fru in the gland prior to Nostoc colonization, genes encoding key enzymes for sucrose and starch hydrolysis (e.g. cell wall invertase, α-amylase, and starch phosphorylase) were expressed at higher levels in stem segments with glands than those without. In contrast, soluble sugars were barely detectable in mucilage freshly secreted from glands. Different sugars affected Nostoc’s ability to differentiate motile hormogonia in a manner consistent with their locations. Galactose and arabinose, the predominant constituents of polysaccharides in the mucilage, had little or no inhibitory effect on hormogonia differentiation. On the other hand, soluble sugars that accumulated in gland tissue, namely sucrose, Glc, and Fru, inhibited hormogonia differentiation and enhanced vegetative growth. Results from this study suggest that, in an N-limited environment, mature Gunnera stem glands may employ different soluble sugars to attract Nostoc and, once the cyanobacteria are internalized, to maintain them in the N2-fixing vegetative state. PMID:20833727

Properties of lotus seed starch-glycerin monostearin complexes formed by high pressure homogenization.

Science.gov (United States)

Chen, Bingyan; Zeng, Shaoxiao; Zeng, Hongliang; Guo, Zebin; Zhang, Yi; Zheng, Baodong

2017-07-01

Starch-lipid complexes were prepared using lotus seed starch (LS) and glycerin monostearate (GMS) via a high pressure homogenization (HPH) process, and the effect of HPH on the physicochemical properties of LS-GMS complexes was investigated. The results of Fourier transform infrared spectroscopy and complex index analysis showed that LS-GMS complexes were formed at 40MPa by HPH and the complex index increased with the increase of homogenization pressure. Scanning electron microscopy displayed LS-GMS complexes present more nest-shape structure with increasing homogenization pressure. X-ray diffraction and differential scanning calorimetry results revealed that V-type crystalline polymorph was formed between LS and GMS, with higher homogenization pressure producing an increasingly stable complex. LS-GMS complex inhibited starch granules swelling, solubility and pasting development, which further reduced peak and breakdown viscosity. During storage, LS-GMS complexes prepared by 70-100MPa had higher Avrami exponent values and lower recrystallization rates compared with native starch, which suggested a lower retrogradation trendency. Copyright © 2017 Elsevier Ltd. All rights reserved.

Improved method for measurement of dietary fiber as non-starch polysaccharides in plant foods.

Science.gov (United States)

Englyst, H N; Cummings, J H

1988-01-01

A method is described that allows rapid estimation of total, soluble, and insoluble dietary fiber as the non-starch polysaccharides (NSP) in plant foods. It is a modification of an earlier, more complex procedure. Starch is completely removed enzymatically, and NSP is measured as the sum of its constituent sugars released by acid hydrolysis. The sugars may, in turn, be measured by gas chromatography (GC), giving values for individual monosaccharides, or more rapidly by colorimetry. Both GC and colorimetry are suitable for routine measurement of total, soluble, and insoluble dietary fiber in cereals, fruits, and vegetables. Values obtained are not affected by food processing so the dietary fiber content of various processed foods and mixed diets can be calculated simply from knowing the amount in the raw materials. The additional information obtained by GC analysis is valuable in the interpretation of physiological studies and in epidemiology where disease is related to type and amount of dietary fiber.

Changes in protein and starch digestibility in sorghum flour during heat-moisture treatments.

Science.gov (United States)

Vu, Thanh-Hien; Bean, Scott; Hsieh, Chao-Feng; Shi, Yong-Cheng

2017-11-01

Heat-moisture treatment (HMT) has been used to modify properties of sorghum starches. However, information is limited on the effects of HMT on the digestibility of starch and the concurrent changes in protein in sorghum flour. The objectives of this research were to identify heat-moisture conditions to increase the resistant starch (RS) content of sorghum flour and investigate changes in sorghum proteins and starch structure. Sorghum flours with different moisture contents (0, 125, 200, and 300 g kg -1 w.b.) were heated at three temperatures (100, 120 and 140 °C) and times (1, 2 and 4 h). HMT of sorghum flour increased its RS level. The flour treated at 200 g kg -1 moisture and 100 °C for 4 h had a high RS content (221 g kg -1 vs. 56 g kg -1 for the untreated flour). Starch was not gelatinized when sorghum flours heated at moisture content of 200 g kg -1 or below. Sorghum protein digestibility and solubility decreased during HMT. The increase in RS of sorghum flour upon HMT was attributed to enhanced amylose-lipid complexes and heat induced structural changes in its protein fraction. HMT can be used to increase RS content in sorghum flour without gelatinizing its starch, thereby providing sorghum flour with unique food applications. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Hyperphosphorylation of cereal starch

DEFF Research Database (Denmark)

Carciofi, Massimiliano; Shaik, Shahnoor Sultana; Jensen, Susanne Langgård

2011-01-01

Plant starch is naturally phosphorylated at a fraction of the C6 and the C3 hydroxyl groups during its biosynthesis in plastids. Starch phosphate esters are important in starch metabolism and they also generate specific industrial functionality. Cereal grains starch contains little starch bound...... phosphate compared with potato tuber starch and in order to investigate the effect of increased endosperm starch phosphate, the potato starch phosphorylating enzyme glucan water dikinase (StGWD) was overexpressed specifically in the developing barley endosperm. StGWD overexpressors showed wild......-type phenotype. Transgenic cereal grains synthesized starch with higher starch bound phosphate content (7.5 (±0.67) nmol/mg) compared to control lines (0.8 (±0.05) nmol/mg) with starch granules showing altered morphology and lower melting enthalpy. Our data indicate specific action of GWD during starch...

Third generation snacks manufactured from orange by-products: physicochemical and nutritional characterization.

Science.gov (United States)

Tovar-Jiménez, Xochitl; Caro-Corrales, José; Gómez-Aldapa, Carlos A; Zazueta-Morales, José; Limón-Valenzuela, Víctor; Castro-Rosas, Javier; Hernández-Ávila, Juan; Aguilar-Palazuelos, Ernesto

2015-10-01

A mixture of orange vesicle flour, commercial nixtamalized corn flour and potato starch was extruded using a Brabender Laboratory single screw extruder (2:1 L/D). The resulting pellets were expanded by microwaves. Expansion index, bulk density, penetration force, carotenoid content, and dietary fiber were measured for this third-generation snack and optimum production conditions were estimated. Response surface methodology was applied using a central composite rotatable experimental design to evaluate the effect of moisture content and extrusion temperature. Temperature mainly affected the expansion index, bulk density and penetration force, while carotenoids content was affected by moisture content. Surface overlap was used to identify optimum processing conditions: temperature: 128-130 °C; moisture content: 22-24 %. Insoluble dietary fiber decreased and soluble dietary fiber increased after extrusion.

Effect of resistant starch on the intestinal health of old dogs: fermentation products and histological features of the intestinal mucosa.

Science.gov (United States)

Peixoto, M C; Ribeiro, É M; Maria, A P J; Loureiro, B A; di Santo, L G; Putarov, T C; Yoshitoshi, F N; Pereira, G T; Sá, L R M; Carciofi, A C

2018-02-01

The effects of resistant starch (RS) intake on nutrient digestibility, microbial fermentation products, faecal IgA, faecal pH, and histological features of the intestinal mucosa of old dogs were evaluated. The same formulation was extruded in two different conditions: one to obtain elevated starch cooking degree with low RS content (0.21%) and the other lower starch cooking with high RS content (1.46%). Eight geriatric Beagles (11.5 ± 0.38 years old) were fed each diet for 61 days in a crossover design. Food intake, nutrient digestibility, fermentation products, faecal pH, and faecal IgA were examined via variance analysis. Histological results of intestinal biopsies were assessed via Wilcoxon test for paired data. The morphometric characteristics of large intestine crypts were evaluated via paired t tests (p Dogs receiving the high-RS diet had lower faecal pH and higher values for propionate, butyrate, total volatile fatty acids, and lactate (p dogs fed the high-RS diet (p = .083). The intake of a corn-based kibble diet manufactured with coarse ground raw material and low starch gelatinization to obtain 1.4% of RS affected microbial fermentation products and faecal pH and tended to increase crypt depth in the descending colon of old dogs. © 2017 Blackwell Verlag GmbH.

Bio rapid prototyping by extruding/aspirating/refilling thermoreversible hydrogel

International Nuclear Information System (INIS)

Iwami, K; Noda, T; Ishida, K; Umeda, N; Morishima, K; Nakamura, M

2010-01-01

This paper reports a method for rapid prototyping of cell tissues, which is based on a system that extrudes, aspirates and refills a mixture of cells and thermoreversible hydrogel as a scaffold. In the extruding mode, a cell-mixed scaffold solution in the sol state is extruded from a cooled micronozzle into a temperature-controlled substrate, which keeps the scaffold in the gel state. In the aspiration mode, the opposite process is performed by Bernoulli suction. In the refilling mode, the solution is extruded into a groove created in the aspiration mode. The minimum width of extruded hydrogel pattern is 114 ± 15 μm by employing a nozzle of diameter 100 μm, and that of aspirated groove was 355 ± 10 μm using a 500 μm-diameter nozzle. Gum arabic is mixed with the scaffold solution to avoid peeling-off of the gel pattern from the substrate. Patterning of Sf-9 cell tissue is demonstrated, and the stability of the patterned cell is investigated. This system offers a procedure for rapid prototyping and local modification of cell scaffolds for tissue engineering.

Physicochemical properties of starches isolated from pumpkin compared with potato and corn starches.

Science.gov (United States)

Przetaczek-Rożnowska, Izabela

2017-08-01

The aim of the study was to characterize the selected physicochemical, thermal and rheological properties of pumpkin starches and compared with the properties of potato and corn starches used as control samples. Pumpkin starches could be used in the food industry as a free gluten starch. Better thermal and rheological properties could contribute to reduce the costs of food production. The syneresis of pumpkin starches was similar to that of potato starch but much lower than that for corn starch. Pasting temperatures of pumpkin starches were lower by 17-21.7°C and their final viscosities were over 1000cP higher than corn paste, but were close to the values obtained for potato starch. The thermodynamic characteristic showed that the transformation temperatures of pumpkin starches were lower than those measured for control starches. A level of retrogradation was much lower in pumpkin starch pastes (32-48%) than was in the case of corn (59%) or potato (77%) starches. The pumpkin starches gels were characterized by a much greater hardness, cohesiveness and chewiness, than potato or corn starches gels. Copyright © 2017 Elsevier B.V. All rights reserved.

Instrumental and sensory properties of pea protein-fortified extruded rice snacks.

Science.gov (United States)

Philipp, Claudia; Buckow, Roman; Silcock, Pat; Oey, Indrawati

2017-12-01

Characteristic attributes of pea-protein fortified, extruded rice snacks were evaluated by mechanical, acoustic and descriptive sensory analysis. The addition of pea protein isolate (0 to 45% (w/w)) to rice flour and extruder screw speed strongly affected the expansion behaviour and therefore, textural attributes of extruded snack products. The sensory panel described the texture of highly expanded extrudates as crisp, while low expanded extrudates were perceived as hard, crunchy and non-crisp. Results of the instrumental and sensory analysis were compared and showed a high correlation between mechanical and sensory hardness (r=0.98), as well as acoustic and sensory crispness (r=0.88). However, poor and/or negative correlations between acoustic and sensory hardness and crunchiness were observed (r=-0.35 and -0.84, respectively). Copyright © 2017 Elsevier Ltd. All rights reserved.

Starch phosphorylation plays an important role in starch biosynthesis

NARCIS (Netherlands)

Xu, Xuan; Dees, Dianka; Dechesne, Annemarie; Huang, Xing Feng; Visser, Richard G.F.; Trindade, Luisa M.

2017-01-01

Starch phosphate esters are crucial in starch metabolism and render valuable functionality to starches for various industrial applications. A potato glucan, water dikinase (GWD1) was introduced in tubers of two different potato genetic backgrounds: an amylose-containing line Kardal and the

Resistant Starch Contents of Native and Heat-Moisture Treated Jackfruit Seed Starch

Directory of Open Access Journals (Sweden)

Ornanong S. Kittipongpatana

2015-01-01

Full Text Available Native jackfruit seed starch (JFS contains 30% w/w type II resistant starch (RS2 and can potentially be developed as a new commercial source of RS for food and pharmaceutical application. Heat-moisture treatment (HMT was explored as a mean to increase RS content of native JFS. The effect of the conditions was tested at varied moisture contents (MC, temperatures, and times. Moisture levels of 20–25%, together with temperatures 80–110°C, generally resulted in increases of RS amount. The highest amount of RS (52.2% was achieved under treatment conditions of 25% MC and 80°C, for 16 h (JF-25-80-16. FT-IR peak ratio at 1047/1022 cm−1 suggested increases in ordered structure in several HMT-JFS samples with increased RS. SEM showed no significant change in the granule appearance, except at high moisture/temperature treatment. XRD revealed no significant change in peaks intensities, suggesting the crystallinity within the granule was mostly retained. DSC showed increases in Tg and, in most cases, ΔT, as the MC was increased in the samples. Slight but significant decreases in ΔH were observed in samples with low RS, indicating that a combination of high moisture and temperature might cause partial gelatinization. HMT-JFS with higher RS exhibited less swelling, while the solubility remained mostly unchanged.

Hydrocolloids Decrease the Digestibility of Corn Starch, Soy Protein, and Skim Milk and the Antioxidant Capacity of Grape Juice.

Science.gov (United States)

Yi, Yue; Jeon, Hyeong-Ju; Yoon, Sun; Lee, Seung-Min

2015-12-01

Hydrocolloids have many applications in foods including their use in dysphagia diets. We aimed to evaluate whether hydrocolloids in foods affect the digestibility of starch and protein, and their effects on antioxidant capacity. The thickening hydrocolloids: locust bean gum and carboxymethyl cellulose, and the gel-forming agents: agar agar, konjac-glucomannan, and Hot & Soft Plus were blended with corn starch and soy protein, skim milk, or grape juice and were examined for their in vitro-digestability by comparing the reducing sugar and trichloroacetic acid (TCA)-soluble peptide, for antioxidant capacity by total polyphenol contents and the 2,2-diphenyl-1-picrylhydrazyl radical scavenging activity. The hydrocolloids resulted in a decrease in starch digestibility with the gel-forming agents. Hydrocolloids diminished TCA-soluble peptides in skim milk compared to soy protein with the exception of locust bean gum and decreased free radical scavenging capacities and total phenolic contents in grape juice. Our findings may provide evidence for the use of hydro-colloids for people at risk of nutritional deficiencies such as dysphagia patients.

Aroma interactions with starch

DEFF Research Database (Denmark)

Jørgensen, Anders Dysted

Starches are used to enhance aroma perception in low-fat foods. Aroma compounds can bind physically to the starch in grooves on the surface or they can form complexes inside amylose helices. This study has been divided into two parts: one part regarding binding of aromas to starches and their aroma......-release, and another part regarding stimulation of a fungal secretome using different carbohydrates. In the first part, nine aromas and one aroma-mixture were mixed with nine different starches, including genetically modified starches. The objective of this sub-project was to bind aromas to the starches to 15 weight......-percent. Aroma binding was tested on both amorphous starches and on native starch granules. A series of aldehydes and alcohols were also tested for binding to the starches. The aromas with the highest volatility were positively retained by starch, whereas for aromas with a lower volatility the starch had...

Enrichment of extruded snack products with coproducts from chestnut mushroom (Agrocybe aegerita) production: interactions between dietary fiber, physicochemical characteristics, and glycemic load.

Science.gov (United States)

Brennan, Margaret A; Derbyshire, Emma; Tiwari, Brijesh K; Brennan, Charles S

2012-05-02

Mushrooms are a common vegetable product that have also been linked to pharmaceutical and medicinal uses. However, the production of the fruiting bodies of mushrooms results in a large quantity of food waste in the form of spent compost. Hyphae and the base of fruit bodies from Agrocybe aegerita were retrieved from spent mushroom compost and refined as a freeze-dried powder. This fiber-rich ingredient was used in the manufacture of ready-to-eat extruded cereal snack products. Inclusions rates were 0, 5, 10, and 15% w/w replacement levels for wheat flour from a control recipe. Inclusion of mushroom coproduct material (MCM) was significantly correlated to increased product expansion (r = 0.848) and density (r = 0.949) but negatively correlated to water absorption index (WAI; r = -0.928) and water solubility index (WSI; r = -0.729). Fiber content could not be correlated to differences in pasting properties of extruded snacks even though snack products with MCM showed significantly lower final viscosity values compared to the control. The potential glycemic response of foods was significantly lowered by including MCM (p extruded snacks (r = 0.916, 0.851, and 0.878. respectively). The results illustrate a reduction in the potential glycemic response from including 5% (w/w) of MCM in extruded snacks exceeds 20%. Thus, the incorporation of MCM in ready-to-eat snack foods may be of considerable interest to the food industry in trying to regulate the glycemic response of foods.

The nutritional properties of extruded and non-extruded corn fiber isolate.

Science.gov (United States)

Artz, W E; Warren, C C; Erdman, J W; Villota, R

1990-01-01

The feed efficiency and selected organ weights of rats fed diets containing 3 or 7% corn fiber, extruded corn fiber or silica were compared to rats fed a fiber-free diet. No significant differences were found in feed efficiency, spleen, lung or liver weights for any of the treatments relative to the fiber-free control diet.

Mechanical, barrier and morphological properties of starch nanocrystals-reinforced pea starch films.

Science.gov (United States)

Li, Xiaojing; Qiu, Chao; Ji, Na; Sun, Cuixia; Xiong, Liu; Sun, Qingjie

2015-05-05

To characterize the pea starch films reinforced with waxy maize starch nanocrystals, the mechanical, water vapor barrier and morphological properties of the composite films were investigated. The addition of starch nanocrystals increased the tensile strength of the composite films, and the value of tensile strength of the composite films was highest when starch nanocrystals content was 5% (w/w). The moisture content (%), water vapor permeability, and water-vapor transmission rate of the composite films significantly decreased as starch nanocrystals content increased. When their starch nanocrystals content was 1-5%, the starch nanocrystals dispersed homogeneously in the composite films, resulting in a relatively smooth and compact film surface and better thermal stability. However, when starch nanocrystals content was more than 7%, the starch nanocrystals began to aggregate, which resulted in the surface of the composite films developing a longitudinal fibrous structure. Copyright © 2014 Elsevier Ltd. All rights reserved.

Evaluation of Blue Value in different plant materials as a tool for rapid starch determination

Directory of Open Access Journals (Sweden)

Bogusław Samotus

2014-01-01

Full Text Available In order to determine the concentration of starch in plant materials from the intensity of the blue iodine complex, it is necessary to know the Blue Value (B.V., which is defined in this paper as the absorbancy of 100 mg of a starch-iodine complex in 100 ml of aqueous solution. An adequate amount of plant material is treated with a hot CaCl2 solution for 1/2 hour and the solute is diluted to 25 ml with CaCl2. This basic solution serves to measure absorbancy, as well as for starch determination. The first measurement is done by the dilution of a proper amount of basic solution with water and after adding a diluted iodine-iodide solution the reading of B.V. is taken off. The second measurement is done by the precipitation of a starch iodine complex from a proper amount of the basic solution, which is then purified, destroyed by Na2SO3 solution, and starch is determined by the anthrone method. These two readings serve for the establishing of B.V. for the starch. Once established, B.V. can be used for starch determination in the proper plant material. A high degree of variation of the B.V. was found. The highest B.V. was obtained for wrinkled pea seeds (17.4; walnut, potato, smooth pea and pear gave values from 12.6 to 11.0, common bean and broad bean - 10.3 and 9.7, Triticale, carrot, rye, wheat and garden parsley from 8.7 to 8.0 and maize, oat, normal rice from 7.6 to 6.2. The B.V. for amylose was 25.3, for potato starch 12.4, soluble starch 11.9, wheat starch 8.8 and for Triticale and rye starches, 8.7.

Barley grain constituents, starch composition, and structure affect starch in vitro enzymatic hydrolysis.

Science.gov (United States)

Asare, Eric K; Jaiswal, Sarita; Maley, Jason; Båga, Monica; Sammynaiken, Ramaswami; Rossnagel, Brian G; Chibbar, Ravindra N

2011-05-11

The relationship between starch physical properties and enzymatic hydrolysis was determined using ten different hulless barley genotypes with variable carbohydrate composition. The ten barley genotypes included one normal starch (CDC McGwire), three increased amylose starches (SH99250, SH99073, and SB94893), and six waxy starches (CDC Alamo, CDC Fibar, CDC Candle, Waxy Betzes, CDC Rattan, and SB94912). Total starch concentration positively influenced thousand grain weight (TGW) (r(2) = 0.70, p starch concentration (r(2) = -0.80, p hydrolysis of pure starch (r(2) = -0.67, p starch concentration (r(2) = 0.46, p starch (RS) in meal and pure starch samples. The rate of starch hydrolysis was high in pure starch samples as compared to meal samples. Enzymatic hydrolysis rate both in meal and pure starch samples followed the order waxy > normal > increased amylose. Rapidly digestible starch (RDS) increased with a decrease in amylose concentration. Atomic force microscopy (AFM) analysis revealed a higher polydispersity index of amylose in CDC McGwire and increased amylose genotypes which could contribute to their reduced enzymatic hydrolysis, compared to waxy starch genotypes. Increased β-glucan and dietary fiber concentration also reduced the enzymatic hydrolysis of meal samples. An average linkage cluster analysis dendrogram revealed that variation in amylose concentration significantly (p starch concentration in meal and pure starch samples. RS is also associated with B-type granules (5-15 μm) and the amylopectin F-III (19-36 DP) fraction. In conclusion, the results suggest that barley genotype SH99250 with less decrease in grain weight in comparison to that of other increased amylose genotypes (SH99073 and SH94893) could be a promising genotype to develop cultivars with increased amylose grain starch without compromising grain weight and yield.

Inducing PLA/starch compatibility through butyl-etherification of waxy and high amylose starch.

Science.gov (United States)

Wokadala, Obiro Cuthbert; Emmambux, Naushad Mohammad; Ray, Suprakas Sinha

2014-11-04

In this study, waxy and high amylose starches were modified through butyl-etherification to facilitate compatibility with polylactide (PLA). Fourier transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy and wettability tests showed that hydrophobic butyl-etherified waxy and high amylose starches were obtained with degree of substitution values of 2.0 and 2.1, respectively. Differential scanning calorimetry, tensile testing, and scanning electron microscopy (SEM) demonstrated improved PLA/starch compatibility for both waxy and high amylose starch after butyl-etherification. The PLA/butyl-etherified waxy and high amylose starch composite films had higher tensile strength and elongation at break compared to PLA/non-butyl-etherified composite films. The morphological study using SEM showed that PLA/butyl-etherified waxy starch composites had a more homogenous microstructure compared to PLA/butyl-etherified high amylose starch composites. Thermogravimetric analysis showed that PLA/starch composite thermal stability decreased with starch butyl-etherification for both waxy and high amylose starches. This study mainly demonstrates that PLA/starch compatibility can be improved through starch butyl-etherification. Copyright © 2014 Elsevier Ltd. All rights reserved.

Processing effects on four prebiotic carbohydrates supplemented in an extruded cereal and a low pH drink

Directory of Open Access Journals (Sweden)

Rebbeca M. Duar

2015-12-01

Full Text Available Prebiotic carbohydrates are added as functional ingredients to a variety of processed foods. Data on the stability of prebiotics during food processing in complex matrices remain limited. The objective of this project was to determine the stability of fructooligosaccharides (FOS, inulin, galactooligosaccharides (GOS, and resistant starch (RS2, when added as ingredients (1% w/w to an extruded cereal and a low pH drink. The cereal was prepared using different screw speeds and barrel temperatures. GOS was not affected by any of the extrusion conditions, whereas inulin decreased significantly at 140 and 170°C. FOS levels decreased in all extrusion conditions, while resistant starch (RS unexpectedly increased for each of the parameters. The low pH drink was prepared with different sucrose to corn syrup solids (S:CSS ratios (1:2, 1:1, 2:1 at pH 3.0, 3.5, and 4.0. The 1:1 S:CSS drink at pH 3.0, negatively impacted FOS and inulin. Moreover, FOS levels decreased when exposed to 1:2 S:CSS (pH 3.5 and 4.0 and 1:1 S:CSS (pH 3.0. GOS and RS were unaffected by any drink formulations. As different conditions impact the stability of prebiotics differently, this study addresses the importance of developing product specific processes for each prebiotic when supplemented into a processed food.

Substituent distribution within cross-linked and hydroxypropylated sweet potato starch and potato starch

NARCIS (Netherlands)

Zhao, J.; Schols, H.A.; Chen Zenghong,; Jin Zhengyu,; Buwalda, P.L.; Gruppen, H.

2012-01-01

Revealing the substituents distribution within starch can help to understand the changes of starch properties after modification. The distribution of substituents over cross-linked and hydroxypropylated sweet potato starch was investigated and compared with modified potato starch. The starches were

Problems, control, and opportunity of starch in the large scale processing of sugarcane and sweet sorghum

Science.gov (United States)

Both sugarcane (Saccharum officinarum) and sweet sorghum (Sorghum bicolor) crops are members of the grass (Poaceae) family, and consist of stalks rich in soluble sugars. The extracted juice from both of these crops contains insoluble starch, with much greater quantities occurring in sweet sorghum. ...

Continuous production of controlled release dosage forms based on hot-melt extruded gum arabic: Formulation development, in vitro characterization and evaluation of potential application fields.

Science.gov (United States)

Kipping, Thomas; Rein, Hubert

2016-01-30

Controlled release matrices based on gum arabic are prepared by applying a continuous hot-melt extrusion technology: the pre-mixture consisting of gum arabic and the incorporated API is plasticized by a co-rotating twin-screw extruder, an intermediate strand is formed by a round nozzle. Single dosed matrices are prepared by cutting the semi elastic strand with a rotary fly cutter. Paracetamol and phenazone are used as model drug substances. High drug loadings up to 70% can be realized. Matrices are characterized concerning their crystalline structure, in vitro dissolution, disintegration time and various physical parameters including glass transition temperature (Tg). Release characteristic behavior is mainly influenced by erosion of the matrices. At higher drug loadings also diffusion based transport gain importance. The solubility of the API shows an influence on the erosion rate of the matrix and should therefore be considered during formulation development. Tg is mainly influenced by the solubility of the API in the surrounding matrix. High soluble phenazone shows a decrease, whereas paracetamol addition has nearly no influence on the Tg of the polymeric system. Activation energy (EA) of the glass transition is determined via dynamic mechanical analysis. The addition of APIs leads to a reduction of EA indicating an increased molecular movement at Tg region compared to placebo extrudates. X-ray diffraction is used to determine the crystalline state of the extruded matrices and interaction between matrix and incorporated APIs. The production of thin layer matrices is an interesting option to provide a fast drug delivery to the oral cavity. High mechanical strength combined with fast disintegration times can be a great advantage for the development of oro-dispersible tablets. A great benefit of the evaluated processing technology is the simple adaption of the final dose by varying either the cutting length or the diameter of the nozzle resulting in a cost

Effect of annealing and heat moisture conditioning on the physicochemical characteristics of bambarra groundnut (Voandzeia subterranea) starch

International Nuclear Information System (INIS)

Adebowale, K.O.; Lawal, O.S.

2002-05-01

Isolated starch of bambarra groundnut (Voandzeia subterranea) was subjected to hydrothermal modifications through annealing and heat moisture conditioning. Both annealing and heat moisture conditioning reduced the swelling power and solubility of the starch. Water binding capacity reduced after annealing, heat moisture conditioning at 18% moisture level (HMB 18 ) and heat moisture conditioning at 21% moisture level (HMB 21 ). Both heat moisture conditioning at 24% moisture level (HMB 24 ) and heat moisture conditioning at 27% moisture level (HMB 27 ) increased the water binding capacity. Hydrothermal modifications reduced the oil absorption capacity of the raw starch. Annealing and heat moisture conditioning reduced the peak viscosity, (Pv) viscosity at 95 deg C (Hv) and viscosity at 95 deg. C after 30 minutes holding (Hv 30 ). However, viscosity increased on cooling down to 50 deg. C after annealing. Annealing and heat moisture treatments as revealed by scanning electron micrograph and light micrograph did not alter the shape and size of the raw starch. The results indicate a rearrangement within the starch granule following hydrothermal treatments. (author)

Quinoa Starch Characteristics and Their Correlations with the Texture Profile Analysis (TPA) of Cooked Quinoa.

Science.gov (United States)

Wu, Geyang; Morris, Craig F; Murphy, Kevin M

2017-10-01

Starch characteristics significantly influence the functionality and end-use quality of cereals and pseudo-cereals. This study examined the composition and properties of starch from 11 pure varieties and 2 commercial samples of quinoa in relationship to the texture of cooked quinoa. Nearly all starch properties and characteristics differed among these samples. Results showed that total starch content of seeds ranged from 53.2 to 75.1 g/100 g apparent amylose content ranged from 2.7% to 16.9%; total amylose ranged from 4.7% to 17.3%; and the degree of amylose-lipid complex ranged from 3.4% to 43.3%. Amylose leaching ranged from 31 mg/100 g starch in "Japanese Strain" to 862 mg/100 g starch in "49ALC." "Japanese Strain" starch also exhibited the highest water solubility (4.5%) and the lowest swelling power (17). α-Amylase activity in "1ESP," "Col.#6197," "Japanese Strain," "QQ63," "Yellow Commercial," and "Red Commercial" (0.03 to 0.09 CU) were significantly lower than the levels of the other quinoa samples (0.20 to 1.16 CU). Additionally, gel texture, thermal properties, and pasting properties of quinoa starches were investigated. Lastly, correlation analysis showed that the quinoa samples with higher amylose content tended to yield harder, stickier, more cohesive, more gummy, and more chewy texture after cooking. A higher degree of amylose-lipid complex and amylose leaching were associated with softer and less chewy cooked quinoa TPA texture. Higher starch enthalpy correlated with firmer, more adhesive, more cohesive, and chewier texture. In sum, starch plays a significant role in the texture of cooked quinoa. The research determined starch characteristics among a diverse set of pure quinoa varieties and commercial samples, and identified the relationships between starch properties and cooked quinoa texture. The results can help breeders and food manufacturers to understand better the relationships among quinoa starch characteristics, cooked quinoa texture, and

Physicochemical and Microstructural Characterization of Corn Starch Edible Films Obtained by a Combination of Extrusion Technology and Casting Technique.

Science.gov (United States)

Fitch-Vargas, Perla Rosa; Aguilar-Palazuelos, Ernesto; de Jesús Zazueta-Morales, José; Vega-García, Misael Odín; Valdez-Morales, Jesús Enrique; Martínez-Bustos, Fernando; Jacobo-Valenzuela, Noelia

2016-09-01

Starch edible films (EFs) have been widely studied due to their potential in food preservation; however, their application is limited because of their poor mechanical and barrier properties. Because of that, the aim of this work was to use the extrusion technology (Ex T) as a pretreatment of casting technique to change the starch structure in order to obtain EFs with improved physicochemical properties. To this, corn starch and a mixture of plasticizers (sorbitol and glycerol, in different ratios) were processed in a twin screw extruder to generate the starch modification and subsequently casting technique was used for EFs formation. The best conditions of the Ex T and plasticizers concentration were obtained using response surface methodology. All the response variables evaluated, were affected significatively by the Plasticizers Ratio (Sorbitol:Glycerol) (PR (S:G)) and Extrusion Temperature (ET), while the Screw Speed (SS) did not show significant effect on any of these variables. The optimization study showed that the appropriate conditions to obtain EFs with the best mechanical and barrier properties were ET = 89 °C, SS = 66 rpm and PR (S:G) = 79.7:20.3. Once the best conditions were obtained, the optimal treatment was characterized according to its microstructural properties (X-ray diffraction, Scanning Electron Microscopy and Atomic Force Microscopy) to determine the damage caused in the starch during Ex T and casting technique. In conclusion, with the combination of Ex T and casting technique were obtained EFs with greater breaking strength and deformation, as well as lower water vapor permeability than those reported in the literature. © 2016 Institute of Food Technologists®

Study on the synthesis and physicochemical properties of starch acetate with low substitution under microwave assistance.

Science.gov (United States)

Lin, Derong; Zhou, Wei; Zhao, Jingjing; Lan, Weijie; Chen, Rongming; Li, Yutong; Xing, Baoshan; Li, Zhuohao; Xiao, Mengshi; Wu, Zhijun; Li, Xindan; Chen, Rongna; Zhang, Xingwen; Chen, Hong; Zhang, Qing; Qin, Wen; Li, Suqing

2017-10-01

In this study, synthesis and physicochemical properties of starch acetate with low substitution under microwave were studied. A three-level-three-factorial Central Composite Design using Response Surface Methodology (RSM) was employed to optimize the reaction conditions. The optimal parameters are as follows: amount of acetic anhydride of 12%, radiation time of 11min, and microwave power of 100W. These optimal conditions predicted by RSM were confirmed that the degree of substitution (DS) of acetate starch is 0.0691mg/g and the physical and chemical properties of natural corn starch (NCS) and corn starch acetate (ACS) were further studied.The transparency, water separation, water absorption, expansion force, and solubility of ACS low substitution are better than NCS, while the NCS's hydrolysis percentage is higher than ACS, which indicate that the modified corn starch has better performance than native corn starch. The surface morphology of the corn starch acetate was examined by scanning electron microscope (SEM), which showed that it had a smooth surface and a spherical and polygonal shape. However, samples' shape is irregular. Crystal structure was observed by X-ray diffraction, and the ACS can determine the level of microwave technology that can destroy the extent of the crystal and amorphous regions. Fourier transform infrared (FTIR) spectroscopy shows that around 1750cm -1 carbonyl signal determines acetylation bonding successfully. Copyright © 2017 Elsevier B.V. All rights reserved.

Modification of Cassava Starch Using Lactic Acid Hydrolysis in The Rotary-UV Dryer to Improve Physichocemical Properties

Directory of Open Access Journals (Sweden)

Sumardiono Siswo

2018-01-01

Full Text Available Food security should be supported in an effort to utilize local products into import substitution products. Cassava starch has the potential to be developed into semi-finished products in the form of flour or starch which does not contain gluten but can inflate large baking process, potentially as a substitute for wheat flour-the main ingredient for making bread. The characteristic of the starch is influenced by the type of starch composition and structure. Natural starch has physicochemical properties i.e. a long time cooking and pasta formed hard. These constraints allow us to modify cassava starch by a combination of lactic acid hydrolysis and drying with rotary UV system. Modified cassava starch is expected to be used as a substitute for wheat flour. The aim of the research which is a combination of lactic acid hydrolysis and drying using a rotary UV system is to examine the optimum operating conditions in the drying process of starch hydrolysis with parameter the physicochemical and rheological properties of modified cassava starch. The initial process study is to hydrolyze cassava starch using lactic acid. Furthermore, hydrolyzed cassava starch is then dried using UV light in the rotary dryers system. There are a variety of changing variables, i.e. time of irradiation cassava starch-lactic acid hydrolysis products in the rotary UV light and air drying temperature. The research results show that modified starch has a better characteristic than the natural starch. From the analysis, the best point of swelling power, solubility and baking expansion is consequently 15.62 g/g; 24.19 %; 2.21 ml/gr. The FTIR result shows that there is no significant difference of the chemical structure because the starch modification only change the physical characteristics. From the SEM analysis, we can know that the size of the starch’s granule changes between the natural starch and the modified starch..

Thermoplastic starch materials prepared from rice starch

International Nuclear Information System (INIS)

Pontes, Barbara R.B.; Curvelo, Antonio A.S.

2009-01-01

Rice starch is a source still little studied for the preparation of thermoplastic materials. However, its characteristics, such as the presence of proteins, fats and fibers may turn into thermoplastics with a better performance. The present study intends the evaluation of the viability of making starch thermoplastic from rice starch and glycerol as plasticizer. The results of X-ray diffraction and scanning electronic microscopy demonstrate the thermoplastic acquisition. The increase of plasticizer content brings on more hydrophilic thermoplastics with less resistance to tension and elongation at break. (author)

The Effects of ZnOnanorodson the Characteristics of Sago Starch Biodegradable Films

Directory of Open Access Journals (Sweden)

R. Alebooyeh

2013-01-01

Full Text Available : Nowadays tend to use biodegradable packaging; including edible coatings and films for free from synthetic chemicals and do not cause environmental pollution, the industry is growing day by day. The aim of this research was to preparation and characterization of biodegradable films supported with ZnOnanorods. In this study, sago starch based films were prepared and   plasticized with sorbitol/ glycerol by casting method. ZnOnanorod with 0, 1, 3and 5%(w/wwas added to the films before casting the films. Films were dried at controlled conditions. Physicochemical properties such as water absorption capacity (WAC, permeability to water vapor (WVP and water solubility of the films were measured.  Also, the effects of addition of nano particles were measured on the antimicrobial properties of the films by agar diffusion method. Results showed that by increasing concentration of ZnOnanorod, solubility in water, WAC, and WVP of the films significantly (p <0.05 decreased. Furthermore, the addition of zinc oxide nanorods showed antimicrobial properties against E. Coli. In summary sago starch films supported with ZnOnanorodscan were used as active packaging for agricultural products as well as food industry. 

Influence of chitosan concentration on mechanical and barrier properties of corn starch/chitosan films.

Science.gov (United States)

Ren, Lili; Yan, Xiaoxia; Zhou, Jiang; Tong, Jin; Su, Xingguang

2017-12-01

The active packaging films based on corn starch and chitosan were prepared through mixing the starch solution and the chitosan solution (1:1) by casting. The aim of this work was to characterize and analyze the effects of the chitosan concentrations (0, 21, 41, 61 and 81wt% of starch) on physicochemical, mechanical and water vapor barrier properties as well as morphological characteristics of the corn starch/chitosan (CS/CH) films. Starch molecules and chitosan could interact through hydrogen bonding as confirmed from the shift of the main peaks to higher wavenumbers in FTIR and the reduction of crystallinity in XRD. Results showed that the incorporation of chitosan resulted in an increase in film solubility, total color differences, tensile strength and elongation at break and a decrease in Young's modulus and water vapor permeability (WVP). Elongation at break of the CS/CH films increased with increasing of chitosan concentration, and reached a maximum at 41 wt%, then declined at higher chitosan concentration. The WVP of CS/CH films increased with an increase of chitosan concentration and the same tendency observed for the moisture content. The results suggest that this biodegradable CS/CH films could potentially be used as active packaging films for food and pharmaceutical applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Green synthesis of highly concentrated aqueous colloidal solutions of large starch-stabilised silver nanoplatelets.

Science.gov (United States)

Cheng, Fei; Betts, Jonathan W; Kelly, Stephen M; Hector, Andrew L

2015-01-01

A simple, environmentally friendly and cost-effective method has been developed to prepare a range of aqueous silver colloidal solutions, using ascorbic acid as a reducing agent, water-soluble starch as a combined crystallising, stabilising and solubilising agent, and water as the solvent. The diameter of silver nanoplatelets increases with higher concentrations of AgNO3 and starch. The silver nanoparticles are also more uniform in shape the greater the diameter of the nanoparticles. Colloidal solutions with a very high concentration of large, flat, hexagonal silver nanoplatelets (~230 nm in breadth) have been used to deposit and fix an antibacterial coating of these large starch-stabilised silver nanoplates on commercial cotton fibres, using a simple dip-coating process using water as the solvent, in order to study the dependence of the antibacterial properties of these nanoplatelets on their size. Copyright © 2014 Elsevier B.V. All rights reserved.

Produção de snacks extrusados à base de polvilho doce e fibra de laranja Production of extruded snacks from cassava starch and orange fiber

Directory of Open Access Journals (Sweden)

Magali Leonel

2010-06-01

Full Text Available Este trabalho teve por objetivo avaliar o efeito da umidade, temperatura de extrusão e rotação da rosca na produção de produtos extrusados expandidos com a utilização do polvilho doce e da polpa de laranja desidratada como matéria-prima. O processo seguiu delineamento central composto rotacional com três fatores, totalizando 15 tratamentos (oito pontos fatoriais, seis pontos axiais e um ponto central com seis repetições. Os produtos obtidos foram caracterizados quanto ao índice de expansão (IE, ao volume específico (VE, ao índice de solubilidade em água (ISA e à cor (L*, a* e b*. Os resultados mostraram efeito das condições operacionais do processo sobre as características físicas dos produtos, e produtos claros com maior expansão e menor solubilidade em água foram obtidos nas condições mais elevadas de temperatura (80-90°C, condições intermediárias de umidade (16% e rotação da rosca (218rpm.This research aimed to evaluate the effect of moisture, extrusion temperature and screw speed in the production of flax snacks using as raw material cassava starch and dehydrated orange pulp. The process followed the central composite rotational design to three factors, totaling 15 treatments (8 factorial points, 6 star points and 1 center point with 6 repetitions. The products obtained were characterized for expansion rate, specific volume, water solubility index and color (L*, a* and b*. The results showed the effect of operational conditions on the physical characteristics of products, and clear products with larger expansion and lower water solubility index were obtained in conditions of the highest temperature (80-90°C and moisture (16% and intermediate screw speed (218rpm.

Effects of β-Glucans and resistant starch on fermentation of recalcitrant fibers in growing pigs

NARCIS (Netherlands)

Vries, de S.; Gerrits, W.J.J.; Kabel, M.A.; Zijlstra, Ruurd; Vasanthan, Thava

2017-01-01

Effects of the presence of β-glucans and resistant starch in diets on nutrient and fiber degradability of rapeseed meal [RSM] (Brassica napus) and Distillers Dried Grain with Solubles (DDGS) were tested in a 2 × 3 factorial arrangement. Two basal diets, containing either 500 g/kg RSM or DDGS and

The effect of gamma irradiation on the functional properties of various starches: A comparative study

International Nuclear Information System (INIS)

Benbettaieb, Nasreddine

2010-01-01

Irradiation is one of the most effective methods able to change starch structure and its functional properties. Effects of irradiation are largely related to particular structure and molecular organisation of starch from various botanical sources. In this research, the effect of gamma irradiation (3, 5, 10, 20, 35 and 50kGy) on the rheological, structural, and morphological properties of three starch varieties (potato, tapioca and wheat) was studied. Rheological analyses show that all the starches develop different behaviours during gelatinization. Potato starch yielded the high swelling power (SP) and exhibited a maximum value of consistency during pasting, followed by that of tapioca one. The lower values of SP and maximum consistency were observed in the case of wheat starch. For all starch varieties, the pic consistency during pasting decrease with increasing irradiation dose. An increase in the SP was observed for all the studied starches irradiated with lower dose (until 20kGy). This parameter decreases at higher doses. On the other hand, irradiation improves the water solubility index (WSI) of all the studied starch. In addition, spectra of Fourier transformed infrared spectroscopy (FTIR) showed that the irradiated starch displayed a significant decrease in the intensity of the OH stretch (3000; 3600 cm -1 ), C H stretch (between 2800 and 3000 cm -1 ), bending mode of water (between 1600 and 1800 cm -1 ) and in the bending mode of glycosidic linkage (between 900 and 950cm -1 ). Structural analysis using electron spins resonance (ESR) illustrates the presence of three signals in 3490, 3500 and 3510 G, respectively. These signals confirm the presence of free radicals in the tapioca and wheat starches through radiation treatment. The X-ray diffraction (XRD) spectra showed that potato starch has B type morphology while tapioca and wheat starches have a crystalline A type morphology. In the same analysis, it was shown that irradiation treatment has no major

EFFECT OF TEMPERATURE AND pH OF MODIFICATION PROCESS ON THE PHYSICAL-MECHANICAL PROPERTIES OF MODIFIED CASSAVA STARCH

Directory of Open Access Journals (Sweden)

Yudi Wicaksono

2016-11-01

Full Text Available The use of cassava starch for excipient in the manufacturing of the tablet has some problems, especially on physical-mechanical properties. The purpose of this study was to determine the effect of the differentness of temperature and pH in the process of modification on the physical-mechanical properties of modified cassava starch. Modifications were performed by suspending cassava starch into a solution of 3 % (w/v PVP K30. The effect of the difference of temperature was observed at temperatures of 25; 45 and 65 0C, while the effect of the difference of pH was observed at pH of 4.0; 7.0 and 12.0. The results showed that the temperature and pH did not affect the physical-mechanical properties of the modified cassava starch. Modification of cassava starch at pH and temperature of 7.0 and 45 0C was produced modified cassava starch with the most excellent solubility, while the best swelling power were formed by the modification process at pH and temperature of 7.0 and 25 0C. Overall, the most excellent compression properties of modified cassava starch resulted from the modification process at pH 12.

Effect of physico-chemical starch properties on bread quality and ageing (model study)

International Nuclear Information System (INIS)

Gambus, H.

1997-01-01

Wheat, rye and triticale starches, both native and those subjected to: segregation according to small granules (type B) and the large ones (type A), defatting with n-propanol and NaOH solution and irradiation by gamma rays at doses 3 and 5 kGy, as well as oat starch were analysed to determine their basic physico-chemical properties. Then all these starches were used in test with baking model pup loaves (40 g) from artificially composed flour, according to starch-gluten system based on recipe (for 4 pup loaves): 80 g starch d.m., 20 g dry vital gluten d.m., 8 g sugar, 3 g salt, 1 g yeast and 70 cm 3 water at 30 o C. Starch was the only alternative component in baking recipes. Additionally, wheat breads of 250 g were baked, in which part of flour was replaced by wheat and triticale starch fraction of large granules, irradiated rye and wheat starches, as well as by oat starch. Pup loaves and 250 g-loaves were evaluated on the day baking and during 3-day storage. Following parameters were determined: volume, penetration and crumb moisture and content of dry matter in crust. Also, sensory scores were performed. In addition, every day water extract from the pup loaves crumbs was prepared and in it dry matter and blue value as an indicator of soluble amylose were determined as well as carbohydrate substances were identified according to molecular mass using gel chromatography. Based on the results obtained negative effects of small starch granules and of a supplement of oat starch on bread quality were found, in spite of a beneficial effect of fatty substances contained in it, on retardation of the crumb hardening process. Also, a positive share of starch phospholipids was ascertained, not only in the retardation of amylose retrogradation but also in stabilization of crumb pores. It was observed that intensity of amylose retrogradation in crumb is determined by both the content of fatty substances in starch granules and the ratio of bound water by starch and protein

Performance properties and antibacterial activity of crosslinked films of quaternary ammonium modified starch and poly(vinyl alcohol).

Science.gov (United States)

Sekhavat Pour, Zahra; Makvandi, Pooyan; Ghaemy, Mousa

2015-09-01

There has been a growing interest in developing antibacterial polymeric materials. In the present work, novel antibacterial cross-linked blend films were prepared based on polyvinyl alcohol (PVA) and quaternary ammonium starch (ST-GTMAC) using citric acid (CA) as plasticizer and glutaraldehyde (GA) as cross-linker. The ST-GTMAC was successfully synthesized from reaction between water-soluble oxidized starch and glycidyltrimethylammonium chloride (GTMAC). The effect of ST-GTMAC, CA and GA contents on the swelling, solubility, mechanical and thermal properties of the films was investigated. It was found that incorporation of ST-GTMAC reduced UV-transmittance and provided antibacterial properties, increasing GA content increased tensile strength and decreased solubility and swelling degree of the films, while CA acted as plasticizer when its concentration was above 10 wt%. The results showed that ST-GTMAC/PVA/CA/GA film has fair antibacterial activity against Gram-positive (Staphylococcus aureus and Bacillus subtilis) and Gram-negative (Escherichia coli and Pseudomonas aeruginosa) bacteria. These results suggest that the prepared film might be used as potential antibacterial material in medical and packaging applications. Copyright © 2015 Elsevier B.V. All rights reserved.

The effects of chilling stress after anthesis on the physicochemical properties of rice (Oryza sativa L) starch.

Science.gov (United States)

Zhu, Dawei; Wei, Haiyan; Guo, Baowei; Dai, Qigen; Wei, Cunxu; Gao, Hui; Hu, Yajie; Cui, Peiyuan; Li, Min; Huo, Zhongyang; Xu, Ke; Zhang, Hongcheng

2017-12-15

This study investigates the effect of chilling stress, over a period of three days after anthesis, on the physicochemical properties of starches derived from six rice cultivars. Chilling stress significantly affected the grain characteristics and physicochemical properties of rice starches, except for those of two varieties, NJ 9108 and ZD 18. In the other four rice cultivars subjected to chilling stress, the content of medium, and large sized granules showed a decrease, and an increase, respectively. Amylose content increased as a result of chilling stress, thereby resulting in starch with a lower swelling power, water solubility, and higher retrogradation enthalpy and gelatinization temperature. Chilling stress led to deterioration of cooked rice quality as determined by the pasting properties of starch. This study indicated that among the cultivars studied, the two rice varieties most resistant to chilling stress after rice anthesis were NJ 9108 and ZD 18. Copyright © 2017 Elsevier Ltd. All rights reserved.

Environmental impact assessment of six starch plastics focusing on wastewater-derived starch and additives

NARCIS (Netherlands)

Broeren, Martijn L.M.; Kuling, Lody; Worrell, Ernst; Shen, Li

2017-01-01

Starch plastics are developed for their biobased origin and potential biodegradability. To assist the development of sustainable starch plastics, this paper quantifies the environmental impacts of starch plastics produced from either virgin starch or starch reclaimed from wastewater. A

Morphology and mechanical properties of PA12/plasticized starch blends prepared by high-shear extrusion

International Nuclear Information System (INIS)

Teyssandier, F.; Cassagnau, P.; Gérard, J.F.; Mignard, N.; Mélis, F.

2012-01-01

Highlights: ► High shear rate processing was found to greatly impact PA12/starch blend morphologies. ► The morphology was observed to be stable under subsequent processing conditions. ► The mechanical properties of the blends under high-shear rate were greatly improved. ► Polymer blend preparation via high-shear processing has proved to be very effective. ► Finally, polymer blends with improved mechanical properties were obtained. - Abstract: PA12/plasticized starch blends (PA12/TPS) were prepared by high-shear twin screw extruder. The morphology development and the mechanical properties of the blends were investigated as a function of the apparent shear rate. High-shear processing has proved to be an efficient method to finely disperse thermoplastic starch in polyamide 12 matrix. Blends containing TPS domains with a size at the nano-scale (R n ∼ 150 nm) homogeneously dispersed in PA12 matrix were obtained. From a modeling point of view, the variation of the droplet radius is closer to the Wu's predictions compared to the Serpe's predictions. From the basic hypothesis of these models, it can be then assumed that compatibilization between both phases occurs during the blend processing. Furthermore, this morphology of the blends has been proved to be stable after a reprocessing step in an internal mixer most likely due to either strong hydrogen bonds between the hydroxyl groups of starch and amide groups of polyamide 12 or to potentially cross reactions between macroradicals accounting for in situ formation of graft copolymers with the potential function of compatibilizers. Mechanical properties of the blends were found to be strongly dependent on the shear rate parameter of blend processing as the mechanical properties increase with shear rate. In agreement to the blend morphology, the elongation at break of the blends was greatly improved attesting of a good adhesion between both phases.

Thermal and mechanical properties of fatty acid starch esters.

Science.gov (United States)

Winkler, H; Vorwerg, W; Rihm, R

2014-02-15

The current study examined thermal and mechanical properties of fatty acid starch esters (FASEs). All highly soluble esters were obtained by the sustainable, homogeneous transesterification of fatty acid vinyl esters in dimethylsulfoxide (DMSO). Casted films of products with a degree of substitution (DS) of 1.40-1.73 were compared with highly substituted ones (DS 2.20-2.63). All films were free of any plasticizer additives. Hydrophobic surfaces were characterized by contact angle measurements. Dynamic scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) revealed thermal transitions (T(g), T(m)) which were influenced by the internal plasticizing effect of the ester groups. Thermal gravimetric analysis (TGA) measurements showed the increased thermal stability toward native starch. Tensile tests revealed the decreasing strength and stiffness of the products with increasing ester-group chain length while the elongation increased up to the ester group laurate and after that decreased. Esters of the longest fatty acids, palmitate and stearate turned out to be brittle materials due to super molecular structures of the ester chains such as confirmed by X-ray. Summarized products with a DS 1.40-1.73 featured more "starch-like" properties with tensile strength up to outstanding 43 MPa, while products with a DS >2 behaved more "oil-like". Both classes of esters should be tested as a serious alternative to commercial starch blends and petrol-based plastics. The term Cnumber is attributed to the number of total C-Atoms of the fatty acid (e.g. C6=Hexanoate). Copyright © 2013 Elsevier Ltd. All rights reserved.

Parametric analysis and design of a screw extruder for slightly non-Newtonian (pseudoplastic materials

Directory of Open Access Journals (Sweden)

J.I. Orisaleye

2018-04-01

Full Text Available Extruders have found application in the food, polymer and pharmaceutical industries. Rheological characteristics of materials are important in the specification of design parameters of screw extruders. Biopolymers, which consist of proteins, nucleic acids and polysaccharides, are shear-thinning (pseudoplastic within normal operating ranges. However, analytical models to predict and design screw extruders for non-Newtonian pseudoplastic materials are rare. In this study, an analytical model suitable to design a screw extruder for slightly non-Newtonian materials was developed. The model was used to predict the performance of the screw extruder while processing materials with power law indices slightly deviating from unity (the Newtonian case. Using non-dimensional analysis, the effects of design and operational parameters were investigated. Expressions to determine the optimum channel depth and helix angle were also derived. The model is capable of predicting the performance of the screw extruder within the range of power law indices considered (1/2⩽n⩽1. The power law index influences the choice of optimum channel depth and helix angle of the screw extruder. Keywords: Screw extruder, Slightly non-Newtonian, Shear-thinning, Pseudoplastic, Biopolymer, Power law

Utilization of α-amylase enzyme from Bacillus stearothermophilus RSAII1B for maltodextrin production from sago starch

Science.gov (United States)

Arfah, R. A.; Ahmad, A.; Dali, S.; Djide, M. N.; Mahdalia; Arif, A. R.

2018-03-01

The dried sago flour derived from Palopo contains 28.80% amylose and 91.23% total carbohydrate. Based on the data, sago starch has the potential to become an alternative raw material for themaltodextrin production. Maltodextrin is one of the starch derivative products produced by hydrolysis process using the α-amylase enzyme with amaximum DE (dextrose equivalent) value of 20. The use of maltodextrin for food and pharmaceutical industries is increasing because of maltodextrin is widely used as thickener filler, surfactant and sugar substitute in milk powder. The aims of this study are to optimize the addition of enzyme concentration and hydrolysis time of α -amylase enzyme to obtain high quality ofmaltodextrin This study also aimed to characterization the obtained maltodextrin. The first step was isolation and purification α-amylase from the isolate of Bacillus stearothermophilus RSAII1B, followed by determination of the α-amylase concentration (0.05%, 0.07% and 0.09%) in 2.0% starch substrate, and the hydrolysis time ofα-amilase (60, 90, 120, 240 minutes). Maltodextrin characters observed were dextrose equivalent (DE), reducing sugar, moisture content, pH changes, color, solubility, viscosity, and total plate count (TPC). The results showed that the value of DE was 12.31, reducing sugar was 11.4%; water content was 10.92%; pH was 4.85; The color of maltodextrin powder was white bone color; solubility was 153.2 g/L; Viscositywas 210-240 cps, TPCwas 380 cfu/g. Maltodextrins produced from sago starch using the α-amylase enzyme from B.stearothermophillus RSAIIm met the quality requirements of SNI 7599: 2010.

The enzymatic determination of starch in food, feed and raw materials of the starch industry

NARCIS (Netherlands)

Brunt, K.; Sanders, P.; Rozema, T.

1998-01-01

An enzymatic starch determination which can be used for the analysis of starch in a very broad range of different samples is evaluated, ranging from starch in plants, feed and food to industrial applications as starch in starch. The method is based on a complete enzymatic conversion of the starch

Surface binding sites in amylase have distinct roles in recognition of starch structure motifs and degradation

DEFF Research Database (Denmark)

Cockburn, Darrell; Nielsen, Morten M.; Christiansen, Camilla

2015-01-01

degrading enzymes and critically important for their function. The affinity towards a variety of starch granules as well as soluble poly- and oligosaccharides of barley alpha-amylase 1 (AMY1) wild-type and mutants of two SBSs (SBS1 and SBS2) was investigated using Langmuir binding analysis, confocal laser...

Analysis of the Retained Gas Sample (RGS) Extruder Assembly

International Nuclear Information System (INIS)

Coverdell, B.L.

1995-09-01

In order for the Retained Gas Sample (RGS) Extruder Assembly to be safely used it was determined by the cognizant engineer that analysis was necessary. The use of the finite-element analysis (FEA) progarm COSMOS/M version 1.71 permitted a quick, easy, and detailed stress analysis of the RGS Extruder Assembly. The FEA model is a three dimensional model using the SHELL4T element type. From the results of the FEA, the cognizant engineer determined that the RGS extruder would be rated at 10,000 lbf and load tested to 12,000 lbf. The respective input and output files for the model are EXTR02.GFM and EXTR02.OUT and can be found on the attached tape

DISINTEGRATION EFFICIENCY OF SODIUM STARCH GLYCOLATES, PREPARED FROM DIFFERENT NATIVE STARCHES

NARCIS (Netherlands)

BOLHUIS, GK; ARENDSCHOLTE, AW; STUUT, GJ; DEVRIES, JA

1994-01-01

In a comparative evaluation, the disintegration efficiency of sodium starch glycolates prepared from seven different native starches (potato, maize, waxy maize, wheat, rice, sago and tapioca) were compared. All the sodium starch glycolates tested had a high swelling capacity, but the rate of water

Starch behaviors and mechanical properties of starch blend films with different plasticizers.

Science.gov (United States)

Nguyen Vu, Hoang Phuong; Lumdubwong, Namfone

2016-12-10

The main objective of the study was to gain insight into structural and mechanical starch behaviors of the plasticized starch blend films. Mechanical properties and starch behaviors of cassava (CS)/and mungbean (MB) (50/50, w/w) starch blend films containing glycerol (Gly) or sorbitol (Sor) at 33% weight content were investigated. It was found that tensile strength TS and %E of the Gly-CSMB films were similar to those of MB films; but%E of all Sor-films was identical. TS of plasticized films increased when AM content and crystallinity increased. When Sor was substituted for Gly, crystallinity of starch films and their TS increased. The CSMB and MB films had somewhat a similar molecular profile and comparable mechanical properties. Therefore, it was proposed the starch molecular profile containing amylopectin with high M¯w, low M¯w of amylose, and the small size of intermediates may impart the high TS and%E of starch films. Copyright © 2016 Elsevier Ltd. All rights reserved.

Characterization of starch films containing starch nanoparticles: part 1: physical and mechanical properties.

Science.gov (United States)

Shi, Ai-Min; Wang, Li-Jun; Li, Dong; Adhikari, Benu

2013-07-25

We report, for the first time, the preparation method and characteristics of starch films incorporating spray dried and vacuum freeze dried starch nanoparticles. Physical properties of these films such as morphology, crystallinity, water vapor permeability (WVP), opacity, and glass transition temperature (Tg) and mechanical properties (strain versus temperature, strain versus stress, Young's modulus and toughness) were measured. Addition of both starch nanoparticles in starch films increased roughness of surface, lowered degree of crystallinity by 23.5%, WVP by 44% and Tg by 4.3°C, respectively compared to those of starch-only films. Drying method used in preparation of starch nanoparticles only affected opacity of films. The incorporation of nanoparticles in starch films resulted into denser films due to which the extent of variation of strain with temperature was much lower. The toughness and Young's modulus of films containing both types of starch nanoparticles were lower than those of control films especially at <100°C. Copyright © 2012 Elsevier Ltd. All rights reserved.

Use of Red Cactus Pear (Opuntia ficus-indica Encapsulated Powder to Pigment Extruded Cereal

Directory of Open Access Journals (Sweden)

Martha G. Ruiz-Gutiérrez

2017-01-01

Full Text Available Encapsulated powder of the red cactus pear is a potential natural dye for the food industry and a known antioxidant. Although the use of this powder is possible, it is not clear how it alters food properties, thus ensuing commercial acceptability. The aim of this study was to evaluate the effect of encapsulated powder of the red cactus pear on the physicochemical properties of extruded cereals. The powder was mixed (2.5, 5.0, and 7.5% w/w with maize grits and extruded (mix moisture 22%, temperature 100°C, and screw speed 325 rpm. The physical, chemical, and sensory characteristics of the extruded cereal were evaluated; extruded cereal without encapsulated powder was used as a control. All cereal extrudates pigmented with the encapsulated powder showed statistically significant differences (P<0.05 in expansion, water absorption, color, density, and texture compared to the control. The encapsulated powder had a positive effect on expansion and water absorption indices, as well as color parameters, but a negative effect on density and texture. Extruded cereal properties were significantly (P<0.05 correlated. Sensorially, consumers accepted the extruded cereal with a lower red cactus pear powder content (2.5% w/w, because this presented characteristics similar to extruded cereal lacking pigment.

Physicochemical properties of starches and proteins in alkali-treated mungbean and cassava starch granules.

Science.gov (United States)

Israkarn, Kamolwan; Na Nakornpanom, Nantarat; Hongsprabhas, Parichat

2014-05-25

This study explored the influences of envelope integrity of cooked starch granules on physicochemical and thermophysical properties of mungbean and cassava starches. Alkali treatment was used to selectively leach amylose from the amorphous region of both starches and partially fragmented starch molecules into lower-molecular-weight polymers. It was found that despite the loss of 40% of the original content of amylose, both mungbean and cassava starches retained similar crystallinities, gelatinization temperature ranges, and pasting profiles compared to the native starches. However, the loss of granule-bound starch synthases during alkali treatment and subsequent alkali cooking in excess water played significant roles in determining granular disintegration. The alterations in envelope integrity due to the negative charge repulsion among polymers within the envelope of swollen granules, and the fragmentation of starch molecules, were responsible for the alterations in thermophysical properties of mungbean and cassava starches cooked under alkaline conditions. Copyright © 2014 Elsevier Ltd. All rights reserved.

Starch meets biotechnology : in planta modification of starch composition and functionalities

NARCIS (Netherlands)

Xu, Xuan

2016-01-01

Storage starch is an energy reservoir for plants and the major source of calories in the human diet. Starch is used in a broad range of industrial applications, as a cheap, abundant, renewable and biodegradable biopolymer. However, starch needs to be modified before it can fulfill the required

Selected Rheological Properties of RS3/4 Type Resistant Starch

Directory of Open Access Journals (Sweden)

Kapelko-Żeberska Małgorzata

2017-12-01

Full Text Available This study was aimed at determining the effect of acetylation degree and crosslinking of retrograded starch with adipic acid on selected rheological properties of prepared pastes and gels. The esterification of retrograded starch allowed obtaining preparations with various degrees of substitution with residues of acetic (0.7–11.2 g/100 g and adipic acids (0.1–0.3 g/100 g. Acetylation and crosslinking caused a decrease in amylose content of the preparations (3–21 g/100 g. Solubility of the preparations in water, in a wide range of variability, was increasing along with an increasing degree of acetylation and with a decreasing degree of crosslinking (19–100 g/100 g. Values of most of the rheological coefficients determined based on the flow curves of the prepared pastes and mechanical spectra of gels (3.5starch. Changes in the rheological properties upon the effect of double modification were not the sum of changes proceeding as a result of single modifications. Instead, interaction of both factors was observed. The conducted modifications enable modelling the properties of produced preparations.

Texturized dairy proteins.

Science.gov (United States)

Onwulata, Charles I; Phillips, John G; Tunick, Michael H; Qi, Phoebi X; Cooke, Peter H

2010-03-01

Dairy proteins are amenable to structural modifications induced by high temperature, shear, and moisture; in particular, whey proteins can change conformation to new unfolded states. The change in protein state is a basis for creating new foods. The dairy products, nonfat dried milk (NDM), whey protein concentrate (WPC), and whey protein isolate (WPI) were modified using a twin-screw extruder at melt temperatures of 50, 75, and 100 degrees C, and moistures ranging from 20 to 70 wt%. Viscoelasticity and solubility measurements showed that extrusion temperature was a more significant (P extruded dairy protein ranged from rigid (2500 N) to soft (2.7 N). Extruding at or above 75 degrees C resulted in increased peak force for WPC (138 to 2500 N) and WPI (2.7 to 147.1 N). NDM was marginally texturized; the presence of lactose interfered with its texturization. WPI products extruded at 50 degrees C were not texturized; their solubility values ranged from 71.8% to 92.6%. A wide possibility exists for creating new foods with texturized dairy proteins due to the extensive range of states achievable. Dairy proteins can be used to boost the protein content in puffed snacks made from corn meal, but unmodified, they bind water and form doughy pastes with starch. To minimize the water binding property of dairy proteins, WPI, or WPC, or NDM were modified by extrusion processing. Extrusion temperature conditions were adjusted to 50, 75, or 100 degrees C, sufficient to change the structure of the dairy proteins, but not destroy them. Extrusion modified the structures of these dairy proteins for ease of use in starchy foods to boost nutrient levels. Dairy proteins can be used to boost the protein content in puffed snacks made from corn meal, but unmodified, they bind water and form doughy pastes with starch. To minimize the water binding property of dairy proteins, whey protein isolate, whey protein concentrate, or nonfat dried milk were modified by extrusion processing. Extrusion

Starch as a source, starch as a sink: the bifunctional role of starch in carbon allocation.

Science.gov (United States)

MacNeill, Gregory J; Mehrpouyan, Sahar; Minow, Mark A A; Patterson, Jenelle A; Tetlow, Ian J; Emes, Michael J

2017-07-20

Starch commands a central role in the carbon budget of the majority of plants on earth, and its biological role changes during development and in response to the environment. Throughout the life of a plant, starch plays a dual role in carbon allocation, acting as both a source, releasing carbon reserves in leaves for growth and development, and as a sink, either as a dedicated starch store in its own right (in seeds and tubers), or as a temporary reserve of carbon contributing to sink strength, in organs such as flowers, fruits, and developing non-starchy seeds. The presence of starch in tissues and organs thus has a profound impact on the physiology of the growing plant as its synthesis and degradation governs the availability of free sugars, which in turn control various growth and developmental processes. This review attempts to summarize the large body of information currently available on starch metabolism and its relationship to wider aspects of carbon metabolism and plant nutrition. It highlights gaps in our knowledge and points to research areas that show promise for bioengineering and manipulation of starch metabolism in order to achieve more desirable phenotypes such as increased yield or plant biomass. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Microstructure, mechanical properties, bio-corrosion properties and cytotoxicity of as-extruded Mg-Sr alloys

Energy Technology Data Exchange (ETDEWEB)

Zhao, Chaoyong [College of Materials Science and Engineering, Chongqing University, Chongqing 400044 (China); Pan, Fusheng, E-mail: fspan@cqu.edu.cn [College of Materials Science and Engineering, Chongqing University, Chongqing 400044 (China); National Engineering Research Center for Magnesium Alloys, Chongqing University, Chongqing 400044 (China); Chongqing Academy of Science and Technology, Chongqing 401123 (China); Zhang, Lei; Pan, Hucheng; Song, Kai; Tang, Aitao [College of Materials Science and Engineering, Chongqing University, Chongqing 400044 (China)

2017-01-01

In this study, as-extruded Mg-Sr alloys were studied for orthopedic application, and the microstructure, mechanical properties, bio-corrosion properties and cytotoxicity of as-extruded Mg-Sr alloys were investigated by optical microscopy, scanning electron microscopy with an energy dispersive X-ray spectroscopy, X-ray diffraction, tensile and compressive tests, immersion test, electrochemical test and cytotoxicity test. The results showed that as-extruded Mg-Sr alloys were composed of α-Mg and Mg{sub 17}Sr{sub 2} phases, and the content of Mg{sub 17}Sr{sub 2} phases increased with increasing Sr content. As-extruded Mg-Sr alloy with 0.5 wt.% Sr was equiaxed grains, while the one with a higher Sr content was long elongated grains and the grain size of the long elongated grains decreased with increasing Sr content. Tensile and compressive tests showed an increase of both tensile and compressive strength and a decrease of elongation with increasing Sr content. Immersion and electrochemical tests showed that as-extruded Mg-0.5Sr alloy exhibited the best anti-corrosion property, and the anti-corrosion property of as-extruded Mg-Sr alloys deteriorated with increasing Sr content, which was greatly associated with galvanic couple effect. The cytotoxicity test revealed that as-extruded Mg-0.5Sr alloy did not induce toxicity to cells. These results indicated that as-extruded Mg-0.5Sr alloy with suitable mechanical properties, corrosion resistance and good cytocompatibility was potential as a biodegradable implant for orthopedic application. - Highlights: • Biodegradable as-extruded Mg-Sr alloys were fabricated. • Microstructure of alloys changed with increasing Sr content. • Mechanical properties of alloys could be controlled by adjusting the Sr content. • Corrosion properties of alloys decreased with increasing Sr content. • As-extruded Mg-0.5Sr alloy was potential for orthopedic application.

Resistant starch in cassava products

Directory of Open Access Journals (Sweden)

Bruna Letícia Buzati Pereira

2014-06-01

Full Text Available Found in different foods, starch is the most important source of carbohydrates in the diet. Some factors present in starchy foods influence the rate at which the starch is hydrolyzed and absorbed in vivo. Due the importance of cassava products in Brazilian diet, the objective of this study was to analyze total starch, resistant starch, and digestible starch contents in commercial cassava products. Thirty three commercial cassava products from different brands, classifications, and origin were analyzed. The method used for determination of resistant starch consisted of an enzymatic process to calculate the final content of resistant starch considering the concentration of glucose released and analyzed. The results showed significant differences between the products. Among the flours and seasoned flours analyzed, the highest levels of resistant starch were observed in the flour from Bahia state (2.21% and the seasoned flour from Paraná state (1.93%. Starch, tapioca, and sago showed levels of resistant starch ranging from 0.56 to 1.1%. The cassava products analyzed can be considered good sources of resistant starch; which make them beneficial products to the gastrointestinal tract.

Cold Extrusion but Not Coating Affects Iron Bioavailability from Fortified Rice in Young Women and Is Associated with Modifications in Starch Microstructure and Mineral Retention during Cooking.

Science.gov (United States)

Hackl, Laura; Speich, Cornelia; Zeder, Christophe; Sánchez-Ferrer, Antoni; Adelmann, Horst; de Pee, Saskia; Tay, Fabian; Zimmermann, Michael B; Moretti, Diego

2017-12-01

retentions >80%, and cooking in excess water did not affect iron retention from hot-extruded rice but caused iron losses of 25% from CER and COR. Distinct variations in starch microstructure were found in CER and HER1. Conclusions: Iron absorption was 64% higher from CER than from hot-extruded rice, with no difference between COR compared with hot-extruded rice. Lower extrusion temperatures may generate a more readily digestible starch structure, allowing for greater iron release in vivo but lower mineral retention during cooking. This trial was registered at clinicaltrials.gov as NCT02176759. © 2017 American Society for Nutrition.

PROTEIN TARGETING TO STARCH is required for localising GRANULE-BOUND STARCH SYNTHASE to starch granules and for normal amylose synthesis in Arabidopsis.

Directory of Open Access Journals (Sweden)

David Seung

2015-02-01

Full Text Available The domestication of starch crops underpinned the development of human civilisation, yet we still do not fully understand how plants make starch. Starch is composed of glucose polymers that are branched (amylopectin or linear (amylose. The amount of amylose strongly influences the physico-chemical behaviour of starchy foods during cooking and of starch mixtures in non-food manufacturing processes. The GRANULE-BOUND STARCH SYNTHASE (GBSS is the glucosyltransferase specifically responsible for elongating amylose polymers and was the only protein known to be required for its biosynthesis. Here, we demonstrate that PROTEIN TARGETING TO STARCH (PTST is also specifically required for amylose synthesis in Arabidopsis. PTST is a plastidial protein possessing an N-terminal coiled coil domain and a C-terminal carbohydrate binding module (CBM. We discovered that Arabidopsis ptst mutants synthesise amylose-free starch and are phenotypically similar to mutants lacking GBSS. Analysis of granule-bound proteins showed a dramatic reduction of GBSS protein in ptst mutant starch granules. Pull-down assays with recombinant proteins in vitro, as well as immunoprecipitation assays in planta, revealed that GBSS physically interacts with PTST via a coiled coil. Furthermore, we show that the CBM domain of PTST, which mediates its interaction with starch granules, is also required for correct GBSS localisation. Fluorescently tagged Arabidopsis GBSS, expressed either in tobacco or Arabidopsis leaves, required the presence of Arabidopsis PTST to localise to starch granules. Mutation of the CBM of PTST caused GBSS to remain in the plastid stroma. PTST fulfils a previously unknown function in targeting GBSS to starch. This sheds new light on the importance of targeting biosynthetic enzymes to sub-cellular sites where their action is required. Importantly, PTST represents a promising new gene target for the biotechnological modification of starch composition, as it is

Effect of high temperature on grain filling period, yield, amylose content and activity of starch biosynthesis enzymes in endosperm of basmati rice.

Science.gov (United States)

Ahmed, Nisar; Tetlow, Ian J; Nawaz, Sehar; Iqbal, Ahsan; Mubin, Muhammad; Nawaz ul Rehman, Muhammad Shah; Butt, Aisha; Lightfoot, David A; Maekawa, Masahiko

2015-08-30

High temperature during grain filling affects yield, starch amylose content and activity of starch biosynthesis enzymes in basmati rice. To investigate the physiological mechanisms underpinning the effects of high temperature on rice grain, basmati rice was grown under two temperature conditions - 32 and 22 °C - during grain filling. High temperature decreased the grain filling period from 32 to 26 days, reducing yield by 6%, and caused a reduction in total starch (3.1%) and amylose content (22%). Measurable activities of key enzymes involved in sucrose to starch conversion, sucrose synthase, ADP-glucose pyrophosphorylase, starch phosphorylase and soluble starch synthase in endosperms developed at 32 °C were lower than those at 22 °C compared with similar ripening stage on an endosperm basis. In particular, granule-bound starch synthase (GBSS) activity was significantly lower than corresponding activity in endosperms developing at 22 °C during all developmental stages analyzed. Results suggest changes in amylose/amylopectin ratio observed in plants grown at 32 °C was attributable to a reduction in activity of GBSS, the sole enzyme responsible for amylose biosynthesis. © 2014 Society of Chemical Industry.

Characterization of tropical starches modified with potassium permanganate and lactic acid

Directory of Open Access Journals (Sweden)

Fabiano Franco Takizawa

2004-11-01

Full Text Available In the present work some tropical starches were modified by an oxidative chemical treatment with potassium permanganate and lactic acid. The native and modified samples were evaluated by mid-infrared spectroscopy, differential dyeing, pH, expansion power, solubility and swelling power, clarity of the pastes, susceptibility to syneresis, carboxyl content and reducing power. All modified samples presented dark blue color, higher expansion power (except corn starch, carboxyl content and reducing power. The solubility of the modified starch granules was very high at 90ºC. At this temperature, it was not possible to measure their swelling power. The viscographic analysis showed decrease in peak viscosity and higher degree of cooking instability. The principal component analysis of the mid-infrared spectra allowed separation between native and modified samples due to the presence of carboxyl groups. The expansion was inversely related with amylose content of the starches.No presente trabalho alguns amidos tropicais foram modificados por tratamento oxidativo com permanganato de potássio e ácido lático. Amidos nativos e modificados foram avaliadas por espectroscopia na região do infravermelho médio, coloração diferencial, pH, propriedade de expansão, poder de inchamento e solubilidade, claridade das pastas, susceptibilidade a sinérese, teor carboxilas e poder redutor. Todas as amostras modificadas adquiriram intensa coloração azul quando suspensas em azul de metileno, maiores valores de expansão (exceto o amido de milho, teor de carboxilas e poder redutor. A solubilidade dos grânulos dos amidos modificados foi muito alta a temperatura de 90°C, não tendo sido possível medir o poder de inchamento. A análise viscográfica mostrou um decréscimo no pico de viscosidade e alta instabilidade ao cozimento. A análise dos componentes principais dos espectros de infravermelho médio permitiu a separação entre as amostras nativas e modificadas

Effect of modified cassava starch on the rheological and quality properties of a dairy beverage prepared with sweet whey

Directory of Open Access Journals (Sweden)

Paola Catalina IMBACHÍ-NARVÁEZ

2018-03-01

Full Text Available Abstract The effect of sweet whey and octenyl succinic anhydride (OSA-modified cassava starch on the quality and rheological properties of fermented dairy beverages was evaluated. Sweet whey (45-65% and OSA-modified cassava starch (0.8-1.2% were added to determine an optimal fermented dairy beverage with the highest viscosity and the lowest syneresis possible. The optimal fermented dairy beverage corresponded to the addition of 40.9% sweet whey and 1.13% OSA-modified cassava starch with respect to the milk and sweet whey mixture. Moreover, the rheological and quality properties of the optimal fermented dairy beverage were compared to a commercial beverage (control during 22 days of storage. No significant differences were found in soluble solids, acidity, pH and consistency index during the time evaluated, while the syneresis of both products showed an increase during storage. OSA-modified cassava starch can be used as a stabiliser in sweet whey fermented dairy beverages because it helps improve its quality properties.

Quality improvement of melt extruded laminar systems using mixture design.

Science.gov (United States)

Hasa, D; Perissutti, B; Campisi, B; Grassi, M; Grabnar, I; Golob, S; Mian, M; Voinovich, D

2015-07-30

This study investigates the application of melt extrusion for the development of an oral retard formulation with a precise drug release over time. Since adjusting the formulation appears to be of the utmost importance in achieving the desired drug release patterns, different formulations of laminar extrudates were prepared according to the principles of Experimental Design, using a design for mixtures to assess the influence of formulation composition on the in vitro drug release from the extrudates after 1h and after 8h. The effect of each component on the two response variables was also studied. Ternary mixtures of theophylline (model drug), monohydrate lactose and microcrystalline wax (as thermoplastic binder) were extruded in a lab scale vertical ram extruder in absence of solvents at a temperature below the melting point of the binder (so that the crystalline state of the drug could be maintained), through a rectangular die to obtain suitable laminar systems. Thanks to the desirability approach and a reliability study for ensuring the quality of the formulation, a very restricted optimal zone was defined within the experimental domain. Among the mixture components, the variation of microcrystalline wax content played the most significant role in overall influence on the in vitro drug release. The formulation theophylline:lactose:wax, 57:14:29 (by weight), selected based on the desirability zone, was subsequently used for in vivo studies. The plasma profile, obtained after oral administration of the laminar extruded system in hard gelatine capsules, revealed the typical trend of an oral retard formulation. The application of the mixture experimental design associated to a desirability function permitted to optimize the extruded system and to determine the composition space that ensures final product quality. Copyright © 2015 Elsevier B.V. All rights reserved.

MICROENCAPSULATION OF TURMERIC OLEORESIN IN BINARY AND TERNARY BLENDS OF GUM ARABIC, MALTODEXTRIN AND MODIFIED STARCH

Directory of Open Access Journals (Sweden)

Diana Maria Cano-Higuita

2015-04-01

Full Text Available Spray-drying is a suitable method to obtain microencapsulated active substances in the powdered form, resulting in powders with improved protection against environmental factors as well as with higher solubility in water, as in the case of turmeric oleoresin. The present study investigated the spray-drying process of turmeric oleoresin microencapsulated with binary and ternary mixtures of different wall materials: gum Arabic, maltodextrin, and modified corn starch. A statistical simplex centroid experimental design was used considering the encapsulation efficiency, curcumin retention, process yield, water content, solubility, and particle morphology as the analyzed responses. Wall matrices containing higher proportions of modified starch and gum Arabic resulted in higher encapsulation efficiency and curcumin retention, whereas the process yield and water content increased with higher proportions of maltodextrin and gum Arabic, respectively. Regression models of the responses were obtained using a surface response method (ANOVA way, showing statistical values of R2 > 0.790. Also, mean analysis was carried out by Tukey's test, permitting to observe some statistical differences between the blends

Alcohol dose dumping: The influence of ethanol on hot-melt extruded pellets comprising solid lipids.

Science.gov (United States)

Jedinger, N; Schrank, S; Mohr, S; Feichtinger, A; Khinast, J; Roblegg, E

2015-05-01

The objective of the present study was to investigate interactions between alcohol and hot-melt extruded pellets and the resulting drug release behavior. The pellets were composed of vegetable calcium stearate as matrix carrier and paracetamol or codeine phosphate as model drugs. Two solid lipids (Compritol® and Precirol®) were incorporated into the matrix to form robust/compact pellets. The drug release characteristics were a strong function of the API solubility, the addition of solid lipids, the dissolution media composition (i.e., alcohol concentration) and correspondingly, the pellet wettability. Pellets comprising paracetamol, which is highly soluble in ethanol, showed alcohol dose dumping regardless of the matrix composition. The wettability increased with increasing ethanol concentrations due to higher paracetamol solubilities yielding increased dissolution rates. For pellets containing codeine phosphate, which has a lower solubility in ethanol than in acidic media, the wettability was a function of the matrix composition. Dose dumping occurred for formulations comprising solid lipids as they showed increased wettabilities with increasing ethanol concentrations. In contrast, pellets comprising calcium stearate as single matrix component showed robustness in alcoholic media due to wettabilities that were not affected by the addition of ethanol. The results clearly indicate that the physico-chemical properties of the drug and the matrix systems are crucial for the design of ethanol-resistant dosage forms. Moreover, hydrophobic calcium stearate can be considered a suitable matrix system that minimizes the risk of ethanol-induced dose dumping for certain API's. Copyright © 2015 Elsevier B.V. All rights reserved.

Antioxidant potential and quality characteristics of vegetable-enriched corn-based extruded snacks.

Science.gov (United States)

Bisharat, G I; Lazou, A E; Panagiotou, N M; Krokida, M K; Maroulis, Z B

2015-07-01

Phenolic content, antioxidant activity and sensory characteristics of vegetable-enriched extrudates were investigated as a result of extrusion conditions, including extrusion temperature (140-180 °C), screw rotation speed (150-250 rpm) and feed moisture content (14-19 % w.b.). Broccoli flour and olive paste was used in mixtures with corn flour at a ratio of 4 to 10 % (broccoli/corn) and 4 to 8 % (olive paste/corn). A simple power model was developed for the prediction of phenolic content and antioxidant activity of extrudates by extrusion conditions and feed composition. Phenolic content and antioxidant activity of broccoli enriched extrudates increased with extrusion temperature and broccoli addition and decreased with feed moisture content. The antioxidant activity of olive paste extrudates increased with material ratio and decreased with feed moisture content and screw rotation. Sensory porosity, homogenous structure, crispness, cohesiveness and melting decreased with feed moisture content, while the latter increased the mealy flavor and hardness of extrudates. Acceptable snacks containing broccoli flour or olive paste can be produced by selecting the appropriate process conditions.

THE MODELING OF COUNTER-ROTATING TWIN-SCREW EXTRUDERS AS REACTORS FOR SINGLE-COMPONENT REACTIONS

NARCIS (Netherlands)

GANZEVELD, KJ; CAPEL, JE; VANDERWAL, DJ; JANSSEN, LPBM

Numerical models are useful to study the behaviour of the extruder as a polymerization reactor. With a correct numerical model a theoretical analysis of the influence of several reaction and extruder parameters can be made, the limitations of the use of the extruder reactor can be determined and the

In vitro digestibility of banana starch cookies.

Science.gov (United States)

Bello-Pérez, Luis A; Sáyago-Ayerdi, Sonia G; Méndez-Montealvo, Guadalupe; Tovar, Juscelino

2004-01-01

Banana starch was isolated and used for preparation of two types of cookies. Chemical composition and digestibility tests were carried out on banana starch and the food products, and these results were compared with corn starch. Ash, protein, and fat levels in banana starch were higher than in corn starch. The high ash amount in banana starch could be due to the potassium content present in this fruit. Proximal analysis was similar between products prepared with banana starch and those based on corn starch. The available starch content of the banana starch preparation was 60% (dmb). The cookies had lower available starch than the starches while banana starch had lower susceptibility to the in vitro alpha-amylolysis reaction. Banana starch and its products had higher resistant starch levels than those made with corn starch.

Effects of cooking methods and starch structures on starch hydrolysis rates of rice.

Science.gov (United States)

Reed, Michael O; Ai, Yongfeng; Leutcher, Josh L; Jane, Jay-lin

2013-07-01

This study aimed to understand effects of different cooking methods, including steamed, pilaf, and traditional stir-fried, on starch hydrolysis rates of rice. Rice grains of 3 varieties, japonica, indica, and waxy, were used for the study. Rice starch was isolated from the grain and characterized. Amylose contents of starches from japonica, indica, and waxy rice were 13.5%, 18.0%, and 0.9%, respectively. The onset gelatinization temperature of indica starch (71.6 °C) was higher than that of the japonica and waxy starch (56.0 and 56.8 °C, respectively). The difference was attributed to longer amylopectin branch chains of the indica starch. Starch hydrolysis rates and resistant starch (RS) contents of the rice varieties differed after they were cooked using different methods. Stir-fried rice displayed the least starch hydrolysis rate followed by pilaf rice and steamed rice for each rice variety. RS contents of freshly steamed japonica, indica, and waxy rice were 0.7%, 6.6%, and 1.3%, respectively; those of rice pilaf were 12.1%, 13.2%, and 3.4%, respectively; and the stir-fried rice displayed the largest RS contents of 15.8%, 16.6%, and 12.1%, respectively. Mechanisms of the large RS contents of the stir-fried rice were studied. With the least starch hydrolysis rate and the largest RS content, stir-fried rice would be a desirable way of preparing rice for food to reduce postprandial blood glucose and insulin responses and to improve colon health of humans. © 2013 Institute of Food Technologists®

Hydrolysis of native and heat-treated starches at sub-gelatinization temperature using granular starch hydrolyzing enzyme.

Science.gov (United States)

Uthumporn, U; Shariffa, Y N; Karim, A A

2012-03-01

The effect of heat treatment below the gelatinization temperature on the susceptibility of corn, mung bean, sago, and potato starches towards granular starch hydrolysis (35°C) was investigated. Starches were hydrolyzed in granular state and after heat treatment (50°C for 30 min) by using granular starch hydrolyzing enzyme for 24 h. Hydrolyzed heat-treated starches showed a significant increase in the percentage of dextrose equivalent compared to native starches, respectively, with corn 53% to 56%, mung bean 36% to 47%, sago 15% to 26%, and potato 12% to 15%. Scanning electron microscopy micrographs showed the presence of more porous granules and surface erosion in heat-treated starch compared to native starch. X-ray analysis showed no changes but with sharper peaks for all the starches, suggested that hydrolysis occurred on the amorphous region. The amylose content and swelling power of heat-treated starches was markedly altered after hydrolysis. Evidently, this enzyme was able to hydrolyze granular starches and heat treatment before hydrolysis significantly increased the degree of hydrolysis.

Development of repetitive railgun pellet accelerator and steady-state solid hydrogen extruder

International Nuclear Information System (INIS)

Oda, Y.; Azuma, K.; Onozuka, M.; Kasai, S.; Hasegawa, K.

1995-01-01

Development of a railgun pellet accelerator and a steady-state solid hydrogen extruder has been conducted. A railgun accelerator has been investigated for a high-speed repetitive pellet acceleration. The final objective is to develop a railgun system that can achieve a 5km/s speed-class repetitive (2Hz) pellet injection. Improvement in the acceleration efficiency showed a pellet velocity of more than 2km/s using augment rails and a ceramic insulator applied to a 1m-long railgun. The other investigation focused on the development of a steady-state solid hydrogen extruder for continuous pellet injection. Screw-driven extruding system has been chosen to extrude the solid hydrogen filament continuously. Theoretical considerations suggest that temperature control of the system is important in future research. (orig.)

Development of repetitive railgun pellet accelerator and steady-state solid hydrogen extruder

Energy Technology Data Exchange (ETDEWEB)

Oda, Y. [Mitsubishi Heavy Industries Ltd., Kobe (Japan); Azuma, K. [Mitsubishi Heavy Industries Ltd., Kobe (Japan); Onozuka, M. [Mitsubishi Heavy Industries Ltd., Kobe (Japan); Kasai, S. [Japan Atomic Energy Research Inst., Ibaraki (Japan); Hasegawa, K. [Japan Atomic Energy Research Inst., Ibaraki (Japan)

1995-12-31

Development of a railgun pellet accelerator and a steady-state solid hydrogen extruder has been conducted. A railgun accelerator has been investigated for a high-speed repetitive pellet acceleration. The final objective is to develop a railgun system that can achieve a 5km/s speed-class repetitive (2Hz) pellet injection. Improvement in the acceleration efficiency showed a pellet velocity of more than 2km/s using augment rails and a ceramic insulator applied to a 1m-long railgun. The other investigation focused on the development of a steady-state solid hydrogen extruder for continuous pellet injection. Screw-driven extruding system has been chosen to extrude the solid hydrogen filament continuously. Theoretical considerations suggest that temperature control of the system is important in future research. (orig.).

Apically extruded dentin debris by reciprocating single-file and multi-file rotary system.

Science.gov (United States)

De-Deus, Gustavo; Neves, Aline; Silva, Emmanuel João; Mendonça, Thais Accorsi; Lourenço, Caroline; Calixto, Camila; Lima, Edson Jorge Moreira

2015-03-01

This study aims to evaluate the apical extrusion of debris by the two reciprocating single-file systems: WaveOne and Reciproc. Conventional multi-file rotary system was used as a reference for comparison. The hypotheses tested were (i) the reciprocating single-file systems extrude more than conventional multi-file rotary system and (ii) the reciprocating single-file systems extrude similar amounts of dentin debris. After solid selection criteria, 80 mesial roots of lower molars were included in the present study. The use of four different instrumentation techniques resulted in four groups (n = 20): G1 (hand-file technique), G2 (ProTaper), G3 (WaveOne), and G4 (Reciproc). The apparatus used to evaluate the collection of apically extruded debris was typical double-chamber collector. Statistical analysis was performed for multiple comparisons. No significant difference was found in the amount of the debris extruded between the two reciprocating systems. In contrast, conventional multi-file rotary system group extruded significantly more debris than both reciprocating groups. Hand instrumentation group extruded significantly more debris than all other groups. The present results yielded favorable input for both reciprocation single-file systems, inasmuch as they showed an improved control of apically extruded debris. Apical extrusion of debris has been studied extensively because of its clinical relevance, particularly since it may cause flare-ups, originated by the introduction of bacteria, pulpal tissue, and irrigating solutions into the periapical tissues.

Ethanol fermentation of HTST extruded rye grain by bacteria and yeasts

Energy Technology Data Exchange (ETDEWEB)

Czarnecki, Z [Univ. of Agriculture, Poznan (Poland). Inst. of Food Technology; Nowak, J [Univ. of Agriculture, Poznan (Poland). Inst. of Food Technology

1997-09-01

High temperature extrusion cooking of rye was used as a pretreatment for ethanol fermentation, and yeasts and bacteria were compared for their fermentation rates. Extrusion cooking caused, on average, a 7.5% increase in ethanol yield in comparison to autoclaved samples. The best results were achieved for grain with a moisture of 21-23% which was extruded at temperatures of 160-180 C. Extrusion decreased the relative viscosity of rye grain water extracts, so it was possible to mash it without {alpha}-amylase. The efficiency of fermentation of extruded rye without Termamyl was equal to that of autoclaved and traditionally mashed rye (using {alpha}-amylase). The rate of fermentation of extruded rye grain by Zymomonas was higher during the first stage, but the final ethanol yield was similar for the bacterium and the yeast. Through both microorganisms gave good quality distillates, the concentration of compounds other than ethanol achieved from extruded rye mashes, which were fermented by Z. mobilis, was five times lower than for yeasts. (orig.)

Extrudable polymer-polymer composites based on ultra-high molecular weight polyethylene

Science.gov (United States)

Panin, S. V.; Kornienko, L. A.; Alexenko, V. O.; Buslovich, D. G.; Dontsov, Yu. V.

2017-12-01

Mechanical and tribotechnical characteristics of polymer-polymeric composites of UHMWPE are studied with the aim of developing extrudable, wear-resistant, self-lubricant polymer mixtures for Additive Manufacturing (AM). The motivation of the study is their further application as feedstocks for 3D printing. Blends of UHMWPE with graft- and block copolymers of low-density polyethylene (HDPE-g-VTMS, HDPE-g-SMA, HDPE-b-EVA), polypropylene (PP), block copolymers of polypropylene and polyamide with linear low density polyethylene (PP-b-LLDPE, PA-b-LLDPE), as well as cross-linked polyethylene (PEX-b), are examined. The choice of compatible polymer components for an ultra- high molecular weight matrix for increasing processability (extrudability) is motivated by the search for commercially available and efficient additives aimed at developing wear-resistant extrudable polymer composites for additive manufacturing. The extrudability, mechanical properties and wear resistance of UHMWPE-based polymer-polymeric composites under sliding friction with different velocities and loads are studied.

Chemical modification and blending of polymers in an extruder reactor

International Nuclear Information System (INIS)

Prut, Eduard V; Zelenetskii, Alexandr N

2001-01-01

Chemical modification and blending of polymers in an extruder reactor are discussed. Relationships between the parameters affecting the reaction kinetics, viz., mixing time, duration of a chemical reaction and the residence time of the system in the extruder reactor, and the structure of the materials produced are analysed. The mechanisms of (i) grafting of low-molecular-mass compounds onto polymers; (ii) reactions between terminal groups of different polymers and (iii) transesterification and interchange reactions are considered. The factors affecting the mechanism of dynamic vulcanisation and the properties of thermoplastic elastomers are identified. Solid-phase reactions of polysaccharides in an extruder are discussed. The priority aspects of studies on the chemical modification and blending of polymers are noted. The bibliography includes 90 references.

Microwave synthesis and adsorption performance of a novel crosslinked starch microsphere

Energy Technology Data Exchange (ETDEWEB)

Lin, Qintie, E-mail: qintlin@163.com [School of Environmental Science and Engineering, Guangdong University of Technology, Guangzhou 510006 (China); National Engineering Laboratory for Rice and By-Product Deep Processing, Center South University of Forestry and Technology, Changsha 41004 (China); Pan, Jianxin [School of Environmental Science and Engineering, Guangdong University of Technology, Guangzhou 510006 (China); Lin, Qinlu [National Engineering Laboratory for Rice and By-Product Deep Processing, Center South University of Forestry and Technology, Changsha 41004 (China); Liu, Qianjun [School of Environmental Science and Engineering, Guangdong University of Technology, Guangzhou 510006 (China)

2013-12-15

Highlights: • CSM was synthesized in a microwave-assisted inversed emulsion system. • The adsorption of methyl violet on CSM was exothermic and spontaneous. • The adsorption process followed the pseudo-second-order kinetics. • The isothermal data obeyed the Langmuir model. • pH variations did not significantly affect the adsorption of methyl violet onto CSM. -- Abstract: A new crosslinked starch microsphere (CSM) was synthesized in a microwave-assisted inversed emulsion system with soluble starch (ST) as a raw material, MBAA as a crosslinker, and K{sub 2}S{sub 2}O{sub 8}–NaHSO{sub 3} as an initiator. The synthesized starch microsphere was characterized and examined by scanning electron microscope (SEM), FTIR spectroscopy and adsorption isotherms of N{sub 2} at 77 K. Adsorption performance was investigated in methyl violet solution. The results showed that the maximum adsorption capacity for MV was 99.3 mg/g at 298 K, and the adsorption fitted pseudo-second-order kinetic model well with correlation coefficients greater than 0.99. The isothermal data obeyed the Langmuir model better compared to Freundlich model and Tempkin model, and the adsorption was exothermic and spontaneous. pH variations (2.0–10.0) did not significantly affect the adsorption of MV onto CSM.

Control of lipid oxidation in extruded salmon jerky snacks.

Science.gov (United States)

Kong, Jian; Perkins, L Brian; Dougherty, Michael P; Camire, Mary Ellen

2011-01-01

A shelf-life study was conducted to evaluate the effect of antioxidants on oxidative stability of extruded jerky-style salmon snacks. Deterioration of docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA) due to lipid oxidation is a major concern for this healthy snack. A control jerky with no added antioxidants and 4 jerkies with antioxidants (rosemary, mixed tocopherols, tertiary butylhydroquinone, and ascorbyl palmitate) added as 0.02% of the lipid content were extruded in duplicate in a Coperion ZSK-25 twin screw extruder. Salmon jerkies from each formulation were placed in 3 mil barrier pouches, flushed with nitrogen, and stored at 35 °C and 75% relative humidity. Lipid oxidation was evaluated as by peroxide value and malonaldehyde content. Other chemical analyses included total fatty acid composition, lipid content, moisture, water activity, pH, and salt. Astaxanthin and CIE L*, a*, b* color were also analyzed at 4-wk intervals. Rosemary inhibited peroxide formation better than did other antioxidants at week 8; no treatment inhibited malonaldehyde levels. All jerkies had lower astaxanthin levels after 8 wk, but rosemary-treated jerky had higher pigment concentrations than did the control at weeks 4 and 8. Protection of omega-3 lipids in these extruded jerkies must be improved to offer consumers a convenient source of these healthful lipids. Practical Application: Salmon flesh can be extruded to produce a jerky that provides 410 mg of omega-3 lipids per serving. Natural antioxidants such as rosemary should be added at levels over 0.02% of the lipid content to help control lipid oxidation. Astaxanthin and CIE a* values correlated well with lipid stability and could be used to monitor quality during storage if initial values are known.

Starch and sucrose synthesis in Phaseolus vulgaris as affected by light, CO2, and abscisic acid

International Nuclear Information System (INIS)

Sharkey, T.D.; Berry, J.A.; Raschke, K.

1985-01-01

Phaseolus vulgaris L. leaves were subjected to various light, CO 2 , and O 2 levels and abscisic acid, then given a 10 minute pulse of 14 CO 2 followed by a 5 minute chase with unlabeled CO 2 . After the chase period, very little label remained in the ionic fractions except at low CO 2 partial pressure. Most label was found in the neutral, alcohol soluble fraction or in the insoluble fraction digestable by amyloglucosidase. Sucrose formation was linearly related to assimilation rate. Starch formation increased linearly with assimilation rate, but did not occur if the assimilation rate was below 4 micromoles per square meter per second. Neither abscisic acid, nor high CO 2 in combination with low O 2 caused significant perturbations of the sucrose/starch formation ratio. These studies indicate that the pathways for starch and sucrose synthesis both are controlled by the rate of net CO 2 assimilation, with sucrose the preferred product at very low assimilation rates

Studies on positive conveying in helically channeled single screw extruders

Directory of Open Access Journals (Sweden)

L. Pan

2012-07-01

Full Text Available A solids conveying theory called double-flight driving theory was proposed for helically channeled single screw extruders. In the extruder, screw channel rotates against static barrel channel, which behaves as cooperative embedded twin-screws for the positive conveying. They turn as two parallel arc plates, between which an arc-plate solid-plug was assumed. By analyzing the forces on the solid-plug in the barrel channel and screw channel, the boundary conditions when the solid-plug is waived of being cut off on barrel wall, were found to have the capacity of the positive conveying. Experimental data were obtained using a specially designed extruder with a helically channeled barrel in the feeding zone and a pressure-adjustable die. The effects of the barrel channel geometry and friction coefficients on the conveying mechanism were presented and compared with the experimental results. The simulations showed that the positive conveying could be achieved after optimizing extruder designs. Compared with the traditional design with the friction-drag conveying, the throughput is higher while screw torque and energy consumption are decreased. Besides, the design criteria of the barrel channel were also discussed.

Microstructure, mechanical properties, bio-corrosion properties and cytotoxicity of as-extruded Mg-Sr alloys.

Science.gov (United States)

Zhao, Chaoyong; Pan, Fusheng; Zhang, Lei; Pan, Hucheng; Song, Kai; Tang, Aitao

2017-01-01

In this study, as-extruded Mg-Sr alloys were studied for orthopedic application, and the microstructure, mechanical properties, bio-corrosion properties and cytotoxicity of as-extruded Mg-Sr alloys were investigated by optical microscopy, scanning electron microscopy with an energy dispersive X-ray spectroscopy, X-ray diffraction, tensile and compressive tests, immersion test, electrochemical test and cytotoxicity test. The results showed that as-extruded Mg-Sr alloys were composed of α-Mg and Mg 17 Sr 2 phases, and the content of Mg 17 Sr 2 phases increased with increasing Sr content. As-extruded Mg-Sr alloy with 0.5wt.% Sr was equiaxed grains, while the one with a higher Sr content was long elongated grains and the grain size of the long elongated grains decreased with increasing Sr content. Tensile and compressive tests showed an increase of both tensile and compressive strength and a decrease of elongation with increasing Sr content. Immersion and electrochemical tests showed that as-extruded Mg-0.5Sr alloy exhibited the best anti-corrosion property, and the anti-corrosion property of as-extruded Mg-Sr alloys deteriorated with increasing Sr content, which was greatly associated with galvanic couple effect. The cytotoxicity test revealed that as-extruded Mg-0.5Sr alloy did not induce toxicity to cells. These results indicated that as-extruded Mg-0.5Sr alloy with suitable mechanical properties, corrosion resistance and good cytocompatibility was potential as a biodegradable implant for orthopedic application. Copyright © 2016 Elsevier B.V. All rights reserved.

Comparison of gamma radiation effects on natural corn and potato starches and modified cassava starch

Science.gov (United States)

Teixeira, Bruna S.; Garcia, Rafael H. L.; Takinami, Patricia Y. I.; del Mastro, Nelida L.

2018-01-01

The objective of this work was to evaluate the effect of irradiation treatment on physicochemical properties of three natural polymers, i.e. native potato and corn starches and a typical Brazilian product, cassava starch modified through fermentation -sour cassava- and also to prepare composite hydrocolloid films based on them. Starches were irradiated in a 60Co irradiation chamber in doses up to 15 kGy, dose rate about 1 kGy/h. Differences were found in granule size distribution upon irradiation, mainly for corn and cassava starch but radiation did not cause significant changes in granule morphology. The viscosity of the potato, corn and cassava starches hydrogels decreased as a function of absorbed dose. Comparing non-irradiated and irradiated starches, changes in the Fourier transform infrared (FTIR) spectra in the 2000-1500 cm-1 region for potato and corn starches were observed but not for the cassava starch. Maximum rupture force of the starch-based films was affected differently for each starch type; color analysis showed that doses of 15 kGy promoted a slight rise in the parameter b* (yellow color) while the parameter L* (lightness) was not significantly affected; X-ray diffraction patterns remained almost unchanged by irradiation.

Sugarcane starch: quantitative determination and characterization

Directory of Open Access Journals (Sweden)

Joelise de Alencar Figueira

2011-09-01

Full Text Available Starch is found in sugarcane as a storage polysaccharide. Starch concentrations vary widely depending on the country, variety, developmental stage, and growth conditions. The purpose of this study was to determine the starch content in different varieties of sugarcane, between May and November 2007, and some characteristics of sugarcane starch such as structure and granules size; gelatinization temperature; starch solution filterability; and susceptibility to glucoamylase, pullulanase, and commercial bacterial and fungal α-amylase enzymes. Susceptibility to debranching amylolytic isoamylase enzyme from Flavobacterium sp. was also tested. Sugarcane starch had spherical shape with a diameter of 1-3 µm. Sugarcane starch formed complexes with iodine, which showed greater absorption in the range of 540 to 620 nm. Sugarcane starch showed higher susceptibility to glucoamylase compared to that of waxy maize, cassava, and potato starch. Sugarcane starch also showed susceptibility to debranching amylolytic pullulanases similar to that of waxy rice starch. It also showed susceptibility to α-amylase from Bacillus subtilis, Bacillus licheniformis, and Aspergillus oryzae similar to that of the other tested starches producing glucose, maltose, maltotriose, maltotetraose, maltopentose and limit α- dextrin.

Quality evaluation of millet-soy blended extrudates formulated through linear programming.

Science.gov (United States)

Balasubramanian, S; Singh, K K; Patil, R T; Onkar, Kolhe K

2012-08-01

Whole pearl millet, finger millet and decorticated soy bean blended (millet soy) extrudates formulations were designed using a linear programming (LP) model to minimize the total cost of the finished product. LP formulated composite flour was extruded through twin screw food extruder at different feed rate (6.5-13.5 kg/h), screw speed (200-350 rpm, constant feed moisture (14% wb), barrel temperature (120 °C) and cutter speed (15 rpm). The physical, functional, textural and pasting characteristics of extrudates were examined and their responses were studied. Expansion index (2.31) and sectional expansion index (5.39) was found to be was found maximum for feed rate and screw speed combination 9.5 kg/h and 250 rpm. However, density (0.25 × 10(-3) g/mm(3)) was maximum for 9.5 kg/h and 300 rpm combination. Maximum color change (10.32) was found for 9.5 kg/h feed rate and 200 rpm screw speed. The lower hardness was obtained for the samples extruded at lowest feed rate (6.5 kg/h) for all screw speed and feed rate at 9.5 kg/h for 300-350 rpm screw speed. Peak viscosity decreases with all screw speed of 9.5 kg/h feed rate.

Starch Spherulites Prepared by a Combination of Enzymatic and Acid Hydrolysis of Normal Corn Starch.

Science.gov (United States)

Shang, Yaqian; Chao, Chen; Yu, Jinglin; Copeland, Les; Wang, Shuo; Wang, Shujun

2018-06-13

This paper describes a new method to prepare spherulites from normal corn starch by a combination of enzymatic (mixtures of α-amylase and amyloglucosidase) and acid hydrolysis followed by recrystallization of the hydrolyzed products. The resulting spherulites contained a higher proportion of chains with a degree of polymerization (DP) of 6-12 and a lower proportion of chains with DP of 25-36, compared to those of native starch. The spherulites had an even particle size of about 2 μm and a typical B-type crystallinity. The amounts of long- and short-range molecular order of double helices in starch spherulites were larger, but the quality of starch crystallites was poorer, compared to that of native starch. This study showed an efficient method for preparing starch spherulites with uniform granule morphology and small particle size from normal corn starch. The ratios of α-amylase and amyloglucosidase in enzymatic hydrolysis had little effect on the structure of the starch spherulites.

A desktop 3D printer with dual extruders to produce customised electronic circuitry

Science.gov (United States)

Butt, Javaid; Onimowo, Dominic Adaoiza; Gohrabian, Mohammed; Sharma, Tinku; Shirvani, Hassan

2018-03-01

3D printing has opened new horizons for the manufacturing industry in general, and 3D printers have become the tools for technological advancements. There is a huge divide between the pricing of industrial and desktop 3D printers with the former being on the expensive side capable of producing excellent quality products and latter being on the low-cost side with moderate quality results. However, there is a larger room for improvements and enhancements for the desktop systems as compared to the industrial ones. In this paper, a desktop 3D printer called Prusa Mendel i2 has been modified and integrated with an additional extruder so that the system can work with dual extruders and produce bespoke electronic circuits. The communication between the two extruders has been established by making use of the In-Chip Serial Programming port on the Arduino Uno controlling the printer. The biggest challenge is to control the flow of electric paint (to be dispensed by the new extruder) and CFD (Computational Fluid Dynamics) analysis has been carried out to ascertain the optimal conditions for proper dispensing. The final product is a customised electronic circuit with the base of plastic (from the 3D printer's extruder) and electronic paint (from the additional extruder) properly dispensed to create a live circuit on a plastic platform. This low-cost enhancement to a desktop 3D printer can provide a new prospect to produce multiple material parts where the additional extruder can be filled with any material that can be properly dispensed from its nozzle.

Dilute solution properties of canary seed (Phalaris canariensis) starch in comparison to wheat starch.

Science.gov (United States)

Irani, Mahdi; Razavi, Seyed M A; Abdel-Aal, El-Sayed M; Hucl, Pierre; Patterson, Carol Ann

2016-06-01

Dilute solution properties of an unknown starch are important to understand its performance and applications in food and non-food industries. In this paper, rheological and molecular properties (intrinsic viscosity, molecular weight, shape factor, voluminosity, conformation and coil overlap parameters) of the starches from two hairless canary seed varieties (CO5041 & CDC Maria) developed for food use were evaluated in the dilute regime (Starch dispersions in DMSO (0.5g/dl)) and compared with wheat starch (WS). The results showed that Higiro model is the best among five applied models for intrinsic viscosity determination of canary seed starch (CSS) and WS on the basis of coefficient of determination (R(2)) and root mean square error (RMSE). WS sample showed higher intrinsic viscosity value (1.670dl/g) in comparison to CSS samples (1.325-1.397dl/g). Berry number and the slope of master curve demonstrated that CSS and WS samples were in dilute domain without entanglement occurrence. The shape factor suggested spherical and ellipsoidal structure for CO5041 starch and ellipsoidal for CDC Maria starch and WS. The molecular weight, coil radius and coil volume of CSSs were smaller than WS. The behavior and molecular characterization of canary seed starch showed its unique properties compared with wheat starch. Copyright © 2016 Elsevier B.V. All rights reserved.

Development and evaluation of garlic incorporated ready-to-eat extruded snacks.

Science.gov (United States)

Haritha, D; Vijayalakshmi, V; Gulla, S

2014-11-01

The present study was carried out to develop and evaluate ready to eat extruded snacks incorporated with garlic powder at various levels (5 %, 10 %, 15 %, 20 %). The organoleptic evaluation was conducted for the developed products and the well accepted products were selected for further studies like physical properties and shelf life (stored at room temperature for 2 months). The organoleptic evaluation of the developed snacks revealed that 15 % and 20 % garlic incorporated snacks were not acceptable due to strong garlic flavor, therefore T1 (control), T2 (5 % garlic) and T3 ( 10 % garlic) were selected for further studies. The physical properties showed significant changes with incorporation of garlic powder at 0 %-10 % level. There was an increase in mass flow rate, tap density and bulk density but decrease in the water holding capacity, oil absorption capacity and expansion ratio. The water soluble index and moisture retention of the products showed the same values for all the three selected treatments. The products were packed by ordinary, nitrogen and vacuum packing and stored for 2 months. It was found that there was an increase in moisture content and microbial load, however the increase was within limits. The increase in the moisture content was low in nitrogen packed products where as the microbial load decreased with increase in the percentage of garlic incorporation. The nitrogen and vacuum packed products showed less microbial load than the ordinary packed products. Garlic powder can be incorporated at 5 and 10 % levels in ready-to-eat extruded snacks with well acceptability and can be stored for a period of 2 months with nitrogen packing as an effective packaging.

Effect of waxy rice flour and cassava starch on freeze-thaw stability of rice starch gels.

Science.gov (United States)

Charoenrein, Sanguansri; Preechathammawong, Nutsuda

2012-10-01

Repeatedly frozen and thawed rice starch gel affects quality. This study investigated how incorporating waxy rice flour (WF) and cassava starch (CS) in rice starch gel affects factors used to measure quality. When rice starch gels containing 0-2% WF and CS were subjected to 5 freeze-thaw cycles, both WF and CS reduced the syneresis in first few cycles. However CS was more effective in reducing syneresis than WF. The different composite arrangement of rice starch with WF or CS caused different mechanisms associated with the rice starch gel retardation of retrogradation, reduced the spongy structure and lowered syneresis. Both swollen granules of rice starch and CS caused an increase in the hardness of the unfrozen and freeze-thawed starch gel while highly swollen WF granules caused softer gels. These results suggested that WF and CS were effective in preserving quality in frozen rice starch based products. Copyright © 2012 Elsevier Ltd. All rights reserved.

IMPACT INJURY DIAGNOSIS IN MANGO THROUGH STARCH DEGRADATION INDEX

Directory of Open Access Journals (Sweden)

FRANCISCO DE ASSIS DE SOUSA

2017-01-01

Full Text Available This study aimed to evaluate the use of starch degradation index (SDI in the diagnosis of areas of impact injuries in 'Tommy Atkins' mango, in different maturation stages. The experiment layout was a fully randomized factorial design (5 x 2, represented by five maturation stages and two handlings, with and without impact, with four replicates. SDI was determined through a subjective scale of scores indicating mango pulp darkened areas by reaction with iodine-potassium iodide solution. Subsequently, these scores were correlated with physicochemical quality variables. The results showed no influence of impact on fruit quality, in any of the studied maturation stages. Moreover, soluble solid contents increased throughout maturation stages, regardless of whether the fruits suffered impact or not. As a result, SDI is unsuitable to indicate fruit impact injury. However, there is a good correlation between SDI and pulp color, vitamin C, pH, titratable acidity, soluble solids, SS/ TA ratio and non-reducing sugars.

Thermomechanical treatment of starch

NARCIS (Netherlands)

Goot, van der A.J.; Einde, van den R.M.

2006-01-01

Starch is used as a major component in many food and nonfood applications and determines the overall product properties to a large extent. It is therefore important to understand the effect of processing on starch. Many starch-based products are produced using a thermal as well as a mechanical

Erosion in extruder flow

Science.gov (United States)

Kaufman, Miron; Fodor, Petru S.

A detailed analysis of the fluid flow in Tadmor's unwound channel model of the single screw extruder is performed by combining numerical and analytical methods. Using the analytical solution for the longitudinal velocity field (in the limit of zero Reynolds number) allows us to devote all the computational resources solely for a detailed numerical solution of the transversal velocity field. This high resolution 3D model of the fluid flow in a single-screw extruder allows us to identify the position and extent of Moffatt eddies that impede mixing. We further consider the erosion of particles (e.g. carbon-black agglomerates) advected by the polymeric flow. We assume a particle to be made of primary fragments bound together. In the erosion process a primary fragment breaks out of a given particle. Particles are advected by the laminar flow and they disperse because of the shear stresses imparted by the fluid. The time evolution of the numbers of particles of different sizes is described by the Bateman coupled differential equations used to model radioactivity. Using the particle size distribution we compute an entropic fragmentation index which varies from 0 for a monodisperse system to 1 for an extreme poly-disperse system.

Diclofenac sodium sustained release hot melt extruded lipid matrices.

Science.gov (United States)

Vithani, K; Cuppok, Y; Mostafa, S; Slipper, I J; Snowden, M J; Douroumis, D

2014-08-01

Sustained release diclofenac sodium (Df-Na) solid lipid matrices with Compritol® 888 ATO were developed in this study. The drug/lipid powders were processed via cold and hot melt extrusion at various drug loadings. The influence of the processing temperatures, drug loading and the addition of excipients on the obtained dissolution rates was investigated. The physicochemical characterization of the extruded batches showed the existence of crystalline drug in the extrudates with a small amount being solubilized in the lipid matrix. The drug content and uniformity on the tablet surface were also investigated by using energy dispersive X-ray microanalysis. The dissolution rates were found to depend on the actual Df-Na loading and the nature of the added excipients, while the effect of the processing temperatures was negligible. The dissolution mechanism of all extruded formulations followed Peppas-Korsemeyer law, based on the estimated determination coefficients and the dissolution constant rates, indicating drug diffusion from the lipid matrices.

Effect of Different Levels of Extruded Soybean and Avizyme Enzyme on Broiler Performance

Directory of Open Access Journals (Sweden)

H Nasiri Mogadam

2012-01-01

Full Text Available An experiment was conducted to examine the effect of different levels of extruded soybean and enzyme on broiler performance. In a completely randomized design with 2×3 factorial arrangement, 480 one day-old, Ross broiler chickens were divided into 40 groups, 12 chicks per pen. Treatments were consisting of combination of four levels of extruded soybean (0.0, 5.0, 10.0 and 15.0 % and two levels of enzyme (0.0 and 500 g per ton. Different levels of extruded soybean and enzyme had no significant effect on blood factors such as cholesterol, triglyceride and the weight of liver and heart. The usage of extruded soybean and enzyme showed significantly higher weight gain and better feed conversion (p

Physicochemical properties of maca starch.

Science.gov (United States)

Zhang, Ling; Li, Guantian; Wang, Sunan; Yao, Weirong; Zhu, Fan

2017-03-01

Maca (Lepidium meyenii Walpers) is gaining research attention due to its unique bioactive properties. Starch is a major component of maca roots, thus representing a novel starch source. In this study, the properties of three maca starches (yellow, purple and black) were compared with commercially maize, cassava, and potato starches. The starch granule sizes ranged from 9.0 to 9.6μm, and the granules were irregularly oval. All the maca starches presented B-type X-ray diffraction patterns, with the relative degree of crystallinity ranging from 22.2 to 24.3%. The apparent amylose contents ranged from 21.0 to 21.3%. The onset gelatinization temperatures ranged from 47.1 to 47.5°C as indicated by differential scanning calorimetry. Significant differences were observed in the pasting properties and textural parameters among all of the studied starches. These characteristics suggest the utility of native maca starch in products subjected to low temperatures during food processing and other industrial applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Using biomass of starch-rich transgenic Arabidopsis vacuolar as feedstock for fermentative hydrogen production

Energy Technology Data Exchange (ETDEWEB)

Lo, Yung-Chung; Cheng, Chieh-Lun; Chen, Chun-Yen [National Cheng Kung Univ., Tainan, Taiwan (China). Dept. of Chemical Engineering; Huang, Li-Fen; Chang, Jo-Shu [Yuan Ze Univ., Tao-yuan, Taiwan (China). Graduate School of Biotechnology and Bioengineering

2010-07-01

Cellulose is the major constitute of plant biomass and highly available in agricultural wastes and industrial effluents, thereby being a cost-effective feedstock for bioenergy production. However, most hydrogen producing bacteria (HPB) could not directly convert cellulosic materials (such as rice husk and rice straw) into hydrogen whereas most HPB could utilize sugar and starch for hydrogen production. In this work, we used an indigenous bacterial isolate Clostridium butyricum CGS2 as HPB, which could directly convert soluble starch into H2 with a maximum H2 production rate and a H2 yield of 205.07 ml H2/h/l and 6.46 mmol H2/g starch, respectively. However, C. butyricum CGS2 could not ferment pure cellulosic materials such as carboxymethyl cellulose and xylan. Moreover, we found that C. butyricum CGS2 could utilize rich husk to produce H2 at a rate of 13.19 ml H2/h/l due to the starch content in rice husk (H2 yield = 1.49 mmol H2/g rice husk). In contrast, since lacking starch content, rice straw cannot be converted to H2 by C. butyricum CGS2. The foregoing results suggest that increasing the starch content in the natural agricultural wastes may make them better feedstock for fermentative H2 production. Hence, a genetically modified plant (Arabidopsis vacuolar) was constructed to enhance its starch concentration. The starch concentration of mutant plant S1 increased to 10.67 mg/fresh weight, which is four times higher than that of wild type plant. Using mutant plant S1 as carbon source, C. butyricum CGS2 was able to give a high cumulative H2 production and H2 production rate of 285.4 ml H2/l and 43.6 ml/h/l, respectively. The cumulative H2 production and H2 production rate both increased when the concentration of the transgenic plant was increased. Therefore, this study successful demonstrated the feasibility of expressing starch on genetically-modified plants to create a more effective feedstock for dark H2 fermentation. (orig.)

Modification of Sodium Release Using Porous Corn Starch and Lipoproteic Matrix.

Science.gov (United States)

Christina, Josephine; Lee, Youngsoo

2016-04-01

Excessive sodium consumption can result in hypertension, diabetes, heart diseases, stroke, and kidney diseases. Various chips and extruded snacks, where salt is mainly applied on the product surface, accounted for almost 56% of snacks retail sales in 2010. Hence, it is important to target sodium reduction for those snack products. Past studies had shown that modifying the rate-release mechanism of sodium is a promising strategy for sodium reduction in the food industry. Encapsulation of salt can be a possible technique to control sodium release rate. Porous corn starch (PCS), created by enzymatic treatment and spray drying and lipoproteic matrix, created by gelation and freeze drying, were evaluated as carriers for controlled sodium release targeting topically applied salts. Both carriers encapsulated salt and their in vitro sodium release profiles were measured using a conductivity meter. The sodium release profiles of PCS treated with different enzymatic reaction times were not significantly different. Protein content and fat content altered sodium release profile from the lipoproteic matrix. The SEM images of PCS showed that most of the salt crystals coated the starch instead of being encapsulated in the pores while the SEM images and computed tomography scan of lipoproteic matrix showed salt dispersed throughout the matrix. Hence, PCS was found to have limitations as a sodium carrier as it could not effectively encapsulate salt inside its pores. The lipoproteic matrix was found to have a potential as a sodium carrier as it could effectively encapsulate salt and modify the sodium release profile. © 2016 Institute of Food Technologists®

Functional properties of irradiated starch

International Nuclear Information System (INIS)

Laouini, Wissal

2011-01-01

Irradiation is an effective method capable of modifying the functional properties of starches. Its effect depends on the specific structural and molecular organization of starch granules from different botanical sources. In this study, we have studied the effect of gamma irradiation (3, 5, 10, 20, 35, 50 kGy) on the rheological properties of some varieties of starch (potato, cassava and wheat). First, we were interested in determining dry matter content; the results showed that the variation in dry matter compared to the control (native starch) is almost zero. So it does not depend on the dose of irradiation. Contrariwise, it differs from a botanical species to another. The viscometer has shown that these starches develop different behaviors during shearing. The native potato starch gave the highest viscosity followed by wheat and cassava which have almost similar viscosities. For all varieties, the viscosity of starch decreases dramatically with an increasing dose of irradiation. At high doses (35 and 50 kGy) the behavior of different starch is similar to that of a viscous pure liquid. The textural analysis via the back-extrusion test showed that increasing the dose of radiation causes a decrease in extrusion force and the energy spent of the different starch throughout the test. Indeed, the extrusion resistance decreases with increasing dose.

Mixture design of rice flour, maize starch and wheat starch for optimization of gluten free bread quality.

Science.gov (United States)

Mancebo, Camino M; Merino, Cristina; Martínez, Mario M; Gómez, Manuel

2015-10-01

Gluten-free bread production requires gluten-free flours or starches. Rice flour and maize starch are two of the most commonly used raw materials. Over recent years, gluten-free wheat starch is available on the market. The aim of this research was to optimize mixtures of rice flour, maize starch and wheat starch using an experimental mixture design. For this purpose, dough rheology and its fermentation behaviour were studied. Quality bread parameters such as specific volume, texture, cell structure, colour and acceptability were also analysed. Generally, starch incorporation reduced G* and increased the bread specific volume and cell density, but the breads obtained were paler than the rice flour breads. Comparing the starches, wheat starch breads had better overall acceptability and had a greater volume than maize-starch bread. The highest value for sensorial acceptability corresponded to the bread produced with a mixture of rice flour (59 g/100 g) and wheat starch (41 g/100 g).

Starch Bioengineering in Barley

DEFF Research Database (Denmark)

Shaik, Shahnoor Sultana

, the effects of engineering high levels of phosphate and amylose content on starch physico-chemical properties were evaluated by various biochemical and morphological studies. As a result, a substantial increase of 10-fold phosphate content and ~99% amylose content with high-resistant starch was observed...... in storage reserve accumulation, metabolite accumulation in AO but no significant differences were observed in HP compared to WT. Scanning electron microscopy and confocal microscopy revealed the details in topography and internal structures of the starch granules in these lines. The results demonstrated......Starch represents the most important carbohydrate used for food and feed purposes. Increasingly, it is also used as a renewable raw material, as a source of biofuel, and for many different industrial applications. Progress in understanding starch biosynthesis, and investigations of the genes...

Future cereal starch bioengineering

DEFF Research Database (Denmark)

Blennow, Andreas; Jensen, Susanne Langgård; Shaik, Shahnoor Sultana

2013-01-01

The importance of cereal starch production worldwide cannot be overrated. However, the qualities and resulting values of existing raw and processed starch do not fully meet future demands for environmentally friendly production of renewable, advanced biomaterials, functional foods, and biomedical...... additives. New approaches for starch bioengineering are needed. In this review, we discuss cereal starch from a combined universal bioresource point of view. The combination of new biotechniques and clean technology methods can be implemented to replace, for example, chemical modification. The recently...... released cereal genomes and the exploding advancement in whole genome sequencing now pave the road for identifying new genes to be exploited to generate a multitude of completely new starch functionalities directly in the cereal grain, converting cereal crops to production plants. Newly released genome...

Process for the production of starch and alcohol from substances containing starch

Energy Technology Data Exchange (ETDEWEB)

Smith, N B; McFate, H A; Eubanks, E M

1969-01-01

Almost complete extraction of starch from wheat, rice, maize, etc., is achieved more economically then by conventional processes. Starch-containing cereal is soaked, the magma is broken and the seed removed. The magma is then drained and separated into a liquid filtrate consisting of starch, gluten and fine fibers, and a solid residue made up of coarse fibers, husks and grit. The liquid filtrate is sieved to remove the fine fibers, and then centrifuged to obtain pure, gluten-free starch. The solid residue is treated with a mineral acid in a converter to give sugar, thus forming a material which is fermented and distilled to give alcohol.

Apically extruded debris with three contemporary Ni-Ti instrumentation systems: an ex vivo comparative study.

Science.gov (United States)

Logani, Ajay; Shah, Naseem

2008-01-01

To comparatively evaluate the amount of apically extruded debris when ProTaper hand, ProTaper rotary and ProFile systems were used for the instrumentation of root canals. Thirty minimally curved, mature, human mandibular premolars with single canals were randomly divided into three groups of ten teeth each. Each group was instrumented using one of the three instrumentation systems: ProTaper hand, ProTaper rotary and ProFile. Five milliliters of sterile water were used as an irrigant. Debris extruded was collected in preweighed polyethylene vials and the extruded irrigant was evaporated. The weight of the dry extruded debris was established by comparing the pre- and postinstrumentation weight of polyethylene vials for each group. The Kruskal-Wallis nonparametric test and Mann-Whitney U test were applied to determine if significant differences existed among the groups ( PProTaper hand and ProFile system ( P > 0.05). Although ProTaper rotary extruded a relatively higher amount of debris, no statistically significant difference was observed between this type and the ProTaper hand instruments ( P > 0.05). The ProTaper rotary extruded significantly more amount of debris compared to the ProFile system ( PProTaper rotary extruded a significantly higher amount of debris than the ProFile.

Continuous Preparation of 1:1 Haloperidol-Maleic Acid Salt by a Novel Solvent-Free Method Using a Twin Screw Melt Extruder.

Science.gov (United States)

Lee, Hung Lin; Vasoya, Jaydip M; Cirqueira, Marilia de Lima; Yeh, Kuan Lin; Lee, Tu; Serajuddin, Abu T M

2017-04-03

Salts are generally prepared by acid-base reaction in relatively large volumes of organic solvents, followed by crystallization. In this study, the potential for preparing a pharmaceutical salt between haloperidol and maleic acid by a novel solvent-free method using a twin-screw melt extruder was investigated. The pH-solubility relationship between haloperidol and maleic acid in aqueous medium was first determined, which demonstrated that 1:1 salt formation between them was feasible (pH max 4.8; salt solubility 4.7 mg/mL). Extrusion of a 1:1 mixture of haloperidol and maleic acid at the extruder barrel temperature of 60 °C resulted in the formation of a highly crystalline salt. The effects of operating temperature and screw configuration on salt formation were also investigated, and those two were identified as key processing parameters. Salts were also prepared by solution crystallization from ethyl acetate, liquid-assisted grinding, and heat-assisted grinding and compared with those obtained by melt extrusion by using DSC, PXRD, TGA, and optical microscopy. While similar salts were obtained by all methods, both melt extrusion and solution crystallization yielded highly crystalline materials with identical enthalpies of melting. During the pH-solubility study, a salt hydrate form was also identified, which, upon heating, converted to anhydrate similar to that obtained by other methods. There were previous reports of the formation of cocrystals, but not salts, by melt extrusion. 1 H NMR and single-crystal X-ray diffraction confirmed that a salt was indeed formed in the present study. The haloperidol-maleic acid salt obtained was nonhygroscopic in the moisture sorption study and converted to the hydrate form only upon mixing with water. Thus, we are reporting for the first time a relatively simple and solvent-free twin-screw melt extrusion method for the preparation of a pharmaceutical salt that provides material comparable to that obtained by solution

Starch Biosynthesis in Crop Plants

Directory of Open Access Journals (Sweden)

Ian J. Tetlow

2018-05-01

Full Text Available Starch is a water-insoluble polyglucan synthesized inside the plastids of plant tissues to provide a store of carbohydrate. Starch harvested from plant storage organs has probably represented the major source of calories for the human diet since before the dawn of civilization. Following the advent of agriculture and the building of complex societies, humans have maintained their dependence on high-yielding domesticated starch-forming crops such as cereals to meet food demands, livestock production, and many non-food applications. The top three crops in terms of acreage are cereals, grown primarily for the harvestable storage starch in the endosperm, although many starchy tuberous crops also provide an important source of calories for various communities around the world. Despite conservation in the core structure of the starch granule, starches from different botanical sources show a high degree of variability, which is exploited in many food and non-food applications. Understanding the factors underpinning starch production and its final structure are of critical importance in guiding future crop improvement endeavours. This special issue contains reviews on these topics and is intended to be a useful resource for researchers involved in improvement of starch-storing crops.

Starch Origin and Thermal Processing Affect Starch Digestion in a Minipig Model of Pancreatic Exocrine Insufficiency.

Science.gov (United States)

Mößeler, Anne; Vagt, Sandra; Beyerbach, Martin; Kamphues, Josef

2015-01-01

Although steatorrhea is the most obvious symptom of pancreatic exocrine insufficiency (PEI), enzymatic digestion of protein and starch is also impaired. Low praecaecal digestibility of starch causes a forced microbial fermentation accounting for energy losses and meteorism. To optimise dietetic measures, knowledge of praecaecal digestibility of starch is needed but such information from PEI patients is rare. Minipigs fitted with an ileocaecal fistula with (n = 3) or without (n = 3) pancreatic duct ligation (PL) were used to estimate the rate of praecaecal disappearance (pcD) of starch. Different botanical sources of starch (rice, amaranth, potato, and pea) were fed either raw or cooked. In the controls (C), there was an almost complete pcD (>92%) except for potato starch (61.5%) which was significantly lower. In PL pcD of raw starch was significantly lower for all sources of starch except for amaranth (87.9%). Thermal processing increased pcD in PL, reaching values of C for starch from rice, potato, and pea. This study clearly underlines the need for precise specification of starch used for patients with specific dietetic needs like PEI. Data should be generated in suitable animal models or patients as tests in healthy individuals would not have given similar conclusions.

Starch Origin and Thermal Processing Affect Starch Digestion in a Minipig Model of Pancreatic Exocrine Insufficiency

Directory of Open Access Journals (Sweden)

Anne Mößeler

2015-01-01

Full Text Available Although steatorrhea is the most obvious symptom of pancreatic exocrine insufficiency (PEI, enzymatic digestion of protein and starch is also impaired. Low praecaecal digestibility of starch causes a forced microbial fermentation accounting for energy losses and meteorism. To optimise dietetic measures, knowledge of praecaecal digestibility of starch is needed but such information from PEI patients is rare. Minipigs fitted with an ileocaecal fistula with (n=3 or without (n=3 pancreatic duct ligation (PL were used to estimate the rate of praecaecal disappearance (pcD of starch. Different botanical sources of starch (rice, amaranth, potato, and pea were fed either raw or cooked. In the controls (C, there was an almost complete pcD (>92% except for potato starch (61.5% which was significantly lower. In PL pcD of raw starch was significantly lower for all sources of starch except for amaranth (87.9%. Thermal processing increased pcD in PL, reaching values of C for starch from rice, potato, and pea. This study clearly underlines the need for precise specification of starch used for patients with specific dietetic needs like PEI. Data should be generated in suitable animal models or patients as tests in healthy individuals would not have given similar conclusions.

Effect of maize starch concentration in the diet on starch and cell wall digestion in the dairy cow.

Science.gov (United States)

van Vuuren, A M; Hindle, V A; Klop, A; Cone, J W

2010-06-01

An in vivo experiment was performed to determine the effect of level of maize starch in the diet on digestion and site of digestion of organic matter, starch and neutral detergent fibre (NDF). In a repeated change-over design experiment, three cows fitted with a rumen cannula and T-piece cannulae in duodenum and ileum received a low-starch (12% of ration dry matter) and a high-starch (33% of ration dry matter) diet. Starch level was increased by exchanging dried sugar beet pulp by ground maize. After a 2-week adaptation period, feed intake, rumen fermentation parameters (in vivo and in situ), intestinal flows, faecal excretion of organic matter, starch and NDF were estimated. When the high-starch diet was fed, dry matter intake was higher (19.0 kg/day vs. 17.8 kg/day), and total tract digestibility of organic matter, starch and NDF was lower when the low-starch diet was fed. Maize starch concentration had no significant effect on rumen pH and volatile fatty acid concentration nor on the site of digestion of organic matter and starch and rate of passage of ytterbium-labelled forage. On the high-starch diet, an extra 1.3 kg of maize starch was supplied at the duodenum in relation to the low-starch diet, but only an extra 0.3 kg of starch was digested in the small intestine. Digestion of NDF was only apparent in the rumen and was lower on the high-starch diet than on the low-starch diet, mainly attributed to the reduction in sugar beet pulp in the high-starch diet. It was concluded that without the correction for the reduction in NDF digestion in the rumen, the extra supply of glucogenic (glucose and propionic acid) and ketogenic nutrients (acetic and butyric acid) by supplemented starch will be overestimated. The mechanisms responsible for these effects need to be addressed in feed evaluation.

Numerical study of internal flow in twin screw extruder and its mixing performance analysis

International Nuclear Information System (INIS)

Kim, Nak Soo; Kim, Hong Bum; Lee, Jae Wook

2006-01-01

We analyzed the non-Newtonian and non-isothermal flow in the melt conveying zone in co-rotating and counter-rotating screw extruder system with the commercial code, STAR-CD, and compared the mixing performance with respect to screw speed and rotating direction. The viscosity of fluid was described by power-law model. The dynamics of mixing was studied numerically by tracking the motion of particles in a twin screw extruder system. The extent of mixing was characterized in terms of the residence time distribution and average strain. The results showed that high screw speed decreases the residence time but increases the shear rate. Therefore higher screw speed increases the strain and has better mixing performance. Counter-rotating screw extruder system and co-rotating screw extruder has the similar shear rate with the same screw speed in spite of different rotating direction. However, the counter-rotating screw has good mixing performance, which is resulted from longer residence time than that of co-rotating screw extruder

Predicting pear (cv. Clara Frijs) dry matter and soluble solids content with near infrared spectroscopy

DEFF Research Database (Denmark)

Travers, Sylvia; Bertelsen, Marianne; Petersen, Karen

2014-01-01

Regression models for predicting preharvest dry matter (DM) and soluble solids content (SSC), based on two spectral ranges (680-1000 nm and 1100-2350 nm), were compared. Models based on longer NIR spectra were more successful for both parameters (DM/SSC: R2 = 0.78-0.84; RMECV = 0.78/0.44; LVs = 6....../7). SSC prediction was better than expected considering the presence of starch in fruit. Generally poor SSC prediction in the presence of starch could be related to the inability of models to distinguish between forms of carbohydrate. Variable selection and regression coefficients highlighted...... fruit. Further research is needed to qualify and build on the results presented here....

Effect of starch types on properties of biodegradable polymer based on thermoplastic starch process by injection molding technique

Directory of Open Access Journals (Sweden)

Yossathorn Tanetrungroj

2015-04-01

Full Text Available In this study effects of different starch types on the properties of biodegradable polymer based on thermoplastic starch (TPS were investigated. Different types of starch containing different contents of amylose and amylopectin were used, i.e. cassava starch, mungbean starch, and arrowroot starch. The TPS polymers were compounded and shaped using an internal mixer and an injection molding machine, respectively. It was found that the amount of amylose and amylopectin contents on native starch influence the properties of the TPS polymer. A high amylose starch of TPMS led to higher strength, hardness, degree of crystallization than the high amylopectin starch of TPCS. In addition, function group analysis by Fourier transforms infrared spectrophotometer, water absorption, and biodegradation by soil burial test were also examined.

Preparation and characterization of composites based on PBAT/Starch blend, micro and nanofillers of bio-CaCO_3

International Nuclear Information System (INIS)

Silva, Valquiria A.; Neto, Jose C. de M.; Moura, Esperidiana A.B.; Tiimob, Boniface; Rangari, Vijaya K.; Silva, Raimundo N.A. da

2015-01-01

Biodegradable polymeric materials have been used as an alternative to synthetic polymeric materials due to their reduced environmental impact. Among the biodegradable polymers is investigated poly (butylene adipate-co-terephthalate) (PBAT). This polymer has the flexibility, high strain at break and easy processing, but a high cost and low toughness that limits their applications. The development of PBAT blends with thermoplastic starch or other biodegradable polymers may lead to a balance of properties, expand its range of applications and also make it more economically viable. The mechanical properties of biodegradable PBAT blends may be further improved by incorporating micro or nanofillers from renewable sources. This study aimed to the processing and characterization of a PBAT/Starch blend reinforced with 2% (wt.) of bioCaCO_3 nanoparticles (nano-bioCaCO_3) and 5% (wt.) of bioCaCO_3-micro (particles ≤ 125 μm). For the preparations were used a co-rotating twin-screw extruder. For the characterization of the prepared materials were used X-ray diffraction (XRD) and tensile test. The XRD results showed the greatest intensity peak of CaCO_3 in the matrix for composites containing bio-CaCO_3 nanofillers suggesting a better interaction between matrix and nanofillers. The results of the tensile test confirmed the better interaction between matrix and nanofillers. These results showed that the addition of only 2 % (wt.) of bio-CaCO_3 nanoparticles in PBAT/Starch blend led to obtaining a tougher material with improved tensile strength and elastic modulus properties regarding the polymer blend. (author)

THE GRAFTING OF MALEIC-ANHYDRIDE ON HIGH-DENSITY POLYETHYLENE IN AN EXTRUDER

NARCIS (Netherlands)

GANZEVELD, KJ; JANSSEN, LPBM

The grafting of maleic anhydride (MAH) on high density polyethylene in a counter-rotating twin screw extruder has been studied. As the reaction kinetics appear to be affected by mass transfer, good micro mixing in the extruder is important. Due to the competing mechanisms of increasing mixing and

Physical, Textural, and Antioxidant Properties of Extruded Waxy Wheat Flour Snack Supplemented with Several Varieties of Bran.

Science.gov (United States)

Fleischman, Emily F; Kowalski, Ryan J; Morris, Craig F; Nguyen, Thuy; Li, Chongjun; Ganjyal, Girish; Ross, Carolyn F

2016-09-28

Wheat represents a ubiquitous commodity and although industries valorize 10% of wheat bran, most of this antioxidant-rich byproduct gets fed to livestock. The objective of this study was to incorporate wheat bran into an extruded snack. Bran samples from hard red spring, soft white club cv. Bruehl, and purple wheat lines were added to cv. Waxy-Pen wheat flour (Triticum aestivum L.) at replacement concentrations of 0%, 12.5%, 25%, and 37.5% (w/w; n = 10). Extrudates were evaluated for antioxidant capacity, color, and physical properties. Results showed that high fiber concentrations altered several pasting properties, reduced expansion ratios (P extrudates. Purple bran supplemented extrudates produced harder products compared to white and red bran treatments (P Extrudates produced with 37.5% (w/w) of each bran variety absorbed more water than the control with no added bran. The oxygen radical absorption capacity assay, expressed as Trolox Equivalents, showed that extrudates made with addition of red (37.5%) and purple (37.5%) bran had higher values compared to the other treatments; the control, red, and white bran treatments had less antioxidant activity after extrusion (P extrudates. Purple and red brans may serve as viable functional ingredients in extruded foods given their higher antioxidant activities. Future studies could evaluate how bran variety and concentration, extruded shape, and flavor influence consumer acceptance. © 2016 Institute of Food Technologists®

Extruder system and method for treatment of a gaseous medium

Energy Technology Data Exchange (ETDEWEB)

Silvi, Norberto; Perry, Robert James; Singh, Surinder Prabhjot; Balch, Gary Stephen; Westendorf, Tiffany Elizabeth Pinard

2016-04-05

A system for treatment of a gaseous medium, comprises an extruder having a barrel. The extruder further comprises a first inlet port, a second inlet port, and a plurality of outlet ports coupled to the barrel. The first inlet port is configured for feeding a lean sorbent, the second inlet port is configured for feeding a gaseous medium, and the plurality of outlet ports are configured for releasing a plurality of components removed from the gaseous medium. Further, the extruder comprises a plurality of helical elements coupled to a plurality of kneading elements, mounted on a shaft, and disposed within the barrel. The barrel and the plurality of helical and kneading elements together form an absorption unit and a desorption unit. The first and second inlet ports are formed in the absorption unit and the plurality of outlet ports are formed in the absorption and desorption units.

Encapsulating fatty acid esters of bioactive compounds in starch

Science.gov (United States)

Lay Ma, Ursula Vanesa

. However, only retinyl palmitate formed a complex with amylopectin. In general, ascorbyl palmitate resulted in the highest complexation, followed by retinyl palmitate and phytosterol ester. The presence of native lipids in Hylon VII starch did not inhibit complex formation. On the contrary, native lipids appear to increase the complexation yield and thermal stability of the starch-fatty acid ester inclusion complexes, possibly due to the formation of ternary complexes. From the three fatty acid esters studied, only ascorbyl palmitate was entrapped in starch spherulites. Various structures including round spherulites, various sizes of torus-shape spherulites, non-spherulitic birefringent and non-birefringent particles, "balloon" morphologies, and gel-like material were formed depending on processing conditions. However, only the torus-shape spherulites, and some non-spherulitic birefringent and non-birefringent particles showed ascorbyl palmitate entrapment. The % yield of the precipitate increased with higher % of added Hylon VII, and decreased with higher heating temperature and faster cooling rates. The amount of entrapped ascorbyl palmitate in the starch precipitate seems to be governed by the amount of this compound added during processing. This study showed that starch can form inclusion complexes with fatty acid esters which may be used for the delivery of certain bioactive molecules. In addition, encapsulation of fatty acid esters in starch spherulites may be a good potential delivery system for water soluble bioactive molecules. However, further research is necessary to gain a better understanding of the type of molecules that can be entrapped in starch spherulites, and the factors affecting spherulitic crystallization and bioactive compound entrapment.

The Dynamics of Starch and Total Sugars during Fruit Development for Ionathan, Starkrimson and Golden Delicious Apple Varieties

Directory of Open Access Journals (Sweden)

Elena Andruţa Mureşan

2015-05-01

Full Text Available Apples represent one of the most important elements in the human diet. The research carried out involved three apple varieties (Starkimson, Ionathan and Golden Delicious harvested during development, which were analyzed in terms of physico-chemical profile. During fruit development, diameter and mass increased continuously for all the three apple varieties studied, acidity decreased and total soluble solids content increased significantly. The pH values of the apple pulp also increased confirming the results obtained for the acidity. The starch concentration was reduced in the early stages of fruit development in all three varieties of apple studied. Starch concentration significantly increased (p <0.05 starting 35 days after full bloom, similar for all three varieties studied. The peak of starch concentration for all three varieties under study was reached at 65 days after full bloom. Starch concentration gradually decreased starting 107 days after full bloom until technological maturity. The results provide important information on how to make the best use of the apple cultivars investigated, and not only, for both technological research and processing practice. Also, they determine the best time to use the apples from physiological falls in different foods and pharmaceuticals.

Potato starch synthases

NARCIS (Netherlands)

Nazarian-Firouzabadi, Farhad; Visser, Richard G.F.

2017-01-01

Starch, a very compact form of glucose units, is the most abundant form of storage polyglucan in nature. The starch synthesis pathway is among the central biochemical pathways, however, our understanding of this important pathway regarding genetic elements controlling this pathway, is still

Chemical Modifications of Starch: Microwave Effect

Directory of Open Access Journals (Sweden)

Kamila Lewicka

2015-01-01

Full Text Available This paper presents basic methods of starch chemical modification, the effect of microwave radiation on the modification process, and the physicochemical properties of starch. It has been shown that the modifications contribute to improvement of the material performance and likewise to significant improvement of its mechanical properties. As a result, more and more extensive use of starch is possible in various industries. In addition, methods of oxidized starch and starch esters preparation are discussed. Properties of microwave radiation and its impact on starch (with particular regard to modifications described in literature are characterized.

Chemical Modifications of Starch: Microwave Effect

OpenAIRE

Lewicka, Kamila; Siemion, Przemysław; Kurcok, Piotr

2015-01-01

This paper presents basic methods of starch chemical modification, the effect of microwave radiation on the modification process, and the physicochemical properties of starch. It has been shown that the modifications contribute to improvement of the material performance and likewise to significant improvement of its mechanical properties. As a result, more and more extensive use of starch is possible in various industries. In addition, methods of oxidized starch and starch esters preparation ...

Enrichment of extruded snack products with whey protein

Directory of Open Access Journals (Sweden)

Mladen Brnčić

2008-08-01

Full Text Available Highest share in products with whey proteins addition belongs to aromatised drinks, aromatised protein bars and various dietetic preparations. In the last few years, there is increased use of the extrusion process for production of food products. This process is, besides other things, used for obtaining directly expanded products, which are immediately packed and sent on market after mechanical and thermal treatment in extruder, or after drying for a short time. One of these food products is “snack” food. Snack food is made with twin corotating screw extruders, in which raw materials are submitted to high temperatures and short time, with intensive expansion and rapid pressure drop. For the production of this category of food products, basic ingredients like corn, wheat, rye and rice, with the maximum of 9 % of proteins, are used. With the development of extrusion technology, special attention is focused on the enrichment of extruded products with different types of proteins, including proteins. In this paper, review of the newest research and achievements in embedding various types of whey concentrates in snack food will be represented. This category of food products for direct consummation is constantly increasing, and addition of whey protein concentrate adds better nutritional value and increased functionality.

Properties of extruded teff-oat composites

Science.gov (United States)

Teff is an ancient grain that is becoming more popular since it is gluten-free and a good source of vitamins, minerals and protein. Relatively little is known about the properties of extruded teff, although the high insoluble fiber and protein contents have been shown to limit expansion. The health ...

Starch Granule Re-Structuring by Starch Branching Enzyme and Glucan Water Dikinase Modulation Affects Caryopsis Physiology and Metabolism

DEFF Research Database (Denmark)

Shaik, Shahnoor S.; Obata, Toshihiro; Hebelstrup, Kim H

2016-01-01

in starch granule morphology at maturity. The results demonstrate that decreasing the storage starch branching resulted in metabolic adjustments and re-directions, tuning to evade deleterious effects on caryopsis physiology and plant performance while only little effect was evident by increasing starch......Starch is of fundamental importance for plant development and reproduction and its optimized molecular assembly is potentially necessary for correct starch metabolism. Re-structuring of starch granules in-planta can therefore potentially affect plant metabolism. Modulation of granule micro...

Starch Granule Re-Structuring by Starch Branching Enzyme and Glucan Water Dikinase Modulation Affects Caryopsis Physiology and Metabolism

DEFF Research Database (Denmark)

Shaik, Shahnoor S.; Obata, Toshihiro; Hebelstrup, Kim H

2016-01-01

Starch is of fundamental importance for plant development and reproduction and its optimized molecular assembly is potentially necessary for correct starch metabolism. Re-structuring of starch granules in-planta can therefore potentially affect plant metabolism. Modulation of granule micro...... in starch granule morphology at maturity. The results demonstrate that decreasing the storage starch branching resulted in metabolic adjustments and re-directions, tuning to evade deleterious effects on caryopsis physiology and plant performance while only little effect was evident by increasing starch...

Powder and compaction characteristics of pregelatinized starches.

Science.gov (United States)

Rojas, J; Uribe, Y; Zuluaga, A

2012-06-01

Pregelatinized starch is widely used as a pharmaceutical aid, especially as a filler-binder. It is known that the tableting performance of excipients could be affected by their source. The aim of this study was to evaluate the powder and tableting properties of pregelatinized starches obtained from yucca, corn and rice and compare those properties with those of Starch 1500. This material had the lowest particle size, and porosity and largest density and best flow. However, yucca starch and corn starch showed an irregular granule morphology, better compactibility and compressibility than Starch 1500. Their onset of plastic deformation and their strain rate sensitivity was comparable to that of Starch 1500. These two materials showed compact disintegration slower that Starch 1500. Conversely, rice starch showed a high elasticity, and friability, low compactibility, which are undesirable for direct compression. This study demonstrated the potential use of pregelatinized starches, especially those obtained from yucca and corn as direct compression filler-binders.

Characteristics of cassava starch fermentation wastewater based on structural degradation of starch granules

Directory of Open Access Journals (Sweden)

Juliane Mascarenhas Pereira

2016-01-01

Full Text Available ABSTRACT: Sour cassava starch is a naturally modified starch produced by fermentation and sun drying, achieving the property of expansion upon baking. Sour cassava starch' bakery products can be prepared without the addition of yeast and it is gluten free. The fermentation process associated with this product has been well studied, but the wastewater, with high acidity and richness in other organic compounds derived from starch degradation, requires further investigation. In this study, the structure of solids present in this residue was studied, seeking to future applications for new materials. The solids of the wastewater were spray dried with maltodextrin (MD with dextrose equivalent (DE of 5 and 15 and the structure of the powder was evaluated by scanning electron microscopy. A regular structure with a network arrangement was observed for the dried material with MD of 5 DE, in contrast to the original and fermented starches structure, which suggests a regular organization of this new material, to be studied in future applications.

Cassava starch films containing acetylated starch nanoparticles as reinforcement: Physical and mechanical characterization.

Science.gov (United States)

Teodoro, Ana Paula; Mali, Suzana; Romero, Natália; de Carvalho, Gizilene Maria

2015-08-01

This paper reports the use of acetylated starch nanoparticles (NPAac) as reinforcement in thermoplastic starch films. NPAac with an average size of approximately 500 nm were obtained by nanoprecipitation. Fourier transform infrared (FTIR) and thermogravimetric analysis (TGA) indicated that NPAac are more thermally stable and essentially amorphous when compared with acetylated starch. Thermoplastic starch films with different proportions of NPAac (0.5, 1.0, 1.5, 10.0%, w/w) were obtained and characterized by scanning electron microscopy (SEM), water vapor permeability (WVP), adsorption isotherms, TGA and mechanical tests. The inclusion of reinforcement caused changes in film properties: WVP was lowered by 41% for film with 1.5% (w/w) of NPAac and moisture adsorption by 33% for film with 10% (w/w) of NPAac; and the Young's modulus and thermal stability were increased by 162% and 15%, respectively, for film with 0.5% (w/w) of NPAac compared to the starch film without the addition of NPAac. Copyright © 2015 Elsevier Ltd. All rights reserved.

An in vitro comparison of apically extruded debris using three rotary nickel-titanium instruments

Directory of Open Access Journals (Sweden)

Tamer Tasdemir

2010-09-01

Conclusion: According to this study, all instrumentation techniques apically extruded debris through the apical foramen. However, the BioRaCe instruments induced less extruded debris than the ProTaper Universal and Mtwo rotary systems.

Heterologous expression of two Arabidopsis starch dikinases in potato

NARCIS (Netherlands)

Xu, Xuan; Dees, Dianka; Huang, Xing Feng; Visser, Richard G.F.; Trindade, Luisa M.

2018-01-01

Starch phosphate esters influence physiochemical properties of starch granules that are essential both for starch metabolism and industrial use of starches. To modify properties of potato starch and understand the effect of starch phosphorylation on starch metabolism in storage starch, the starch

Reduced starch granule number per chloroplast in the dpe2/phs1 mutant is dependent on initiation of starch degradation.

Science.gov (United States)

Malinova, Irina; Fettke, Joerg

2017-01-01

An Arabidopsis double knock-out mutant lacking cytosolic disproportionating enzyme 2 (DPE2) and the plastidial phosphorylase (PHS1) revealed a dwarf-growth phenotype, reduced starch content, an uneven distribution of starch within the plant rosette, and a reduced number of starch granules per chloroplast under standard growth conditions. In contrast, the wild type contained 5-7 starch granules per chloroplast. Mature and old leaves of the double mutant were essentially starch free and showed plastidial disintegration. Several analyses revealed that the number of starch granules per chloroplast was affected by the dark phase. So far, it was unclear if it was the dark phase per se or starch degradation in the dark that was connected to the observed decrease in the number of starch granules per chloroplast. Therefore, in the background of the double mutant dpe2/phs1, a triple mutant was generated lacking the initial starch degrading enzyme glucan, water dikinase (GWD). The triple mutant showed improved plant growth, a starch-excess phenotype, and a homogeneous starch distribution. Furthermore, the number of starch granules per chloroplast was increased and was similar to wild type. However, starch granule morphology was only slightly affected by the lack of GWD as in the triple mutant and, like in dpe2/phs1, more spherical starch granules were observed. The characterized triple mutant was discussed in the context of the generation of starch granules and the formation of starch granule morphology.

Resistant starch: promise for improving human health.

Science.gov (United States)

Birt, Diane F; Boylston, Terri; Hendrich, Suzanne; Jane, Jay-Lin; Hollis, James; Li, Li; McClelland, John; Moore, Samuel; Phillips, Gregory J; Rowling, Matthew; Schalinske, Kevin; Scott, M Paul; Whitley, Elizabeth M

2013-11-01

Ongoing research to develop digestion-resistant starch for human health promotion integrates the disciplines of starch chemistry, agronomy, analytical chemistry, food science, nutrition, pathology, and microbiology. The objectives of this research include identifying components of starch structure that confer digestion resistance, developing novel plants and starches, and modifying foods to incorporate these starches. Furthermore, recent and ongoing studies address the impact of digestion-resistant starches on the prevention and control of chronic human diseases, including diabetes, colon cancer, and obesity. This review provides a transdisciplinary overview of this field, including a description of types of resistant starches; factors in plants that affect digestion resistance; methods for starch analysis; challenges in developing food products with resistant starches; mammalian intestinal and gut bacterial metabolism; potential effects on gut microbiota; and impacts and mechanisms for the prevention and control of colon cancer, diabetes, and obesity. Although this has been an active area of research and considerable progress has been made, many questions regarding how to best use digestion-resistant starches in human diets for disease prevention must be answered before the full potential of resistant starches can be realized.

Extruded pea (Pisum sativum as alternative to soybean protein for dairy cows feeding in organic Alpine farms

Directory of Open Access Journals (Sweden)

Flaviana Gottardo

2010-04-01

Full Text Available The study evaluated the use of extruded pea as an alternative to soybean in the protein feeding of dairy cattle raised in organic Alpine farms. The research was carried out in a commercial organic dairy farm located in the Province of Trento (Northern Italy and it considered two separate periods of cows’ lactation: early and late lactation. According to the traditional management practice of alpine dairy herds with the seasonal calving of the cows in early winter, the former period was carried out during the cold season when cows were housed indoors, while the latter period started after the transfer of the entire herd to an alpine pasture for the summer grazing. In both periods, 16 cows of Rendena breed were equally assigned to 2 experimental groups. The dietary forage (meadow hay in early lactation or pasture in late lactation was supplemented to one group of cows with a Control concentrate in which soybean expeller, sunflower expeller and wheat bran were the main protein feeds. Soybean proteins were replaced by extruded peas in the Soy-free concentrate given to the other group of cows. The daily amount of concentrate was adjusted to the individual milk yield on a weekly basis adopting ratios of 0.360 and 0.125 kg of DM per kg of milk in early and late lactation periods, respectively. Cows receiving Soy-free concentrate showed a higher milk yield than the Control cows in both lactation periods (18.7 vs 17.5 kg/d in early lactation and 9.3 vs 8.6 kg/d on pasture, respectively. Milk fat and protein were not affected by the diet at any stage of lactation, while a higher concentration of milk urea was observed in milk samples taken from Soy-free cows in both periods of the study. This result could have been promoted by the higher soluble fraction of extruded pea proteins in comparison to that of soybean expeller. Cows feeding behaviour was monitored only in the early lactation period and despite of the different amount of concentrate consumed by

Impact of local hydrothermal treatment during bread baking on soluble amylose, firmness, amylopectin retrogradation and water mobility during bread staling.

Science.gov (United States)

Besbes, Emna; Le Bail, Alain; Seetharaman, Koushik

2016-01-01

The impact of hydrothermal processing undergone by bread dough during baking on the degree of starch granule disruption, on leaching of soluble amylose, on water mobility, on firmness and on amylopectin retrogradation during staling has been investigated. Two heating rates during baking have been considered (4.67 and 6.31 °C/min) corresponding respectively to baking temperature of 220 and 240 °C. An increase in firmness and in the amount of retrogradated amylopectin accompanied by a decrease in freezable water has been observed during staling. Although a lower heating rate yielded in larger amount of retrogradated amylopectin retrogradation, it resulted in a lower firmness. Additionally, the amount of soluble amylose and the relaxation times of water measured by Nuclear Magnetic Resonance NMR (T20, T21 and T22) decreased during staling. It was demonstrated that the amount of soluble amylose was higher for bread crumb baked at lower heating rate, indicating that an increasing amount of amylose is leached outside the starch granules. This was corresponding to a greater amount of retrograded amylopectin during staling. Moreover, it was found that the degree of gelatinization differs locally in a same bread slice between the top, the centre and the bottom locations in the crumb. This was attributed to the differences in kinetics of heating, the availability of water during baking and the degree of starch granule disruption during baking. Based on first order kinetic model, it was found that staling kinetics were faster for samples baked at higher heating rate.