WorldWideScience

Sample records for solid kr precipitates

  1. Modeling studies on the precipitation of Kr after implantation into metals

    International Nuclear Information System (INIS)

    Rest, J.

    1988-02-01

    A rate-theory approach is applied to interpreting observations on the precipitation of Kr injected into Ni at temperatures between 25 and 560/degree/C. At temperatures of 400/degree/C or higher, the implanted Kr precipitates evolve into a bi-modal size distribution containing small solid precipitates and an additional population of larger, faceted bubbles. The calculations explore the dependence of the observed bi-modal distribution on the maximum size of the solid Kr precipitates and the effect of this dependence on bubble mobility. The analysis suggests that during the irradiation, whereas the large bubbles move by surface diffusion, the solid Kr precipitates are immobile. The relevance of the Kr-Ni interaction on the solid Kr precipitates size cutoff is discussed. 18 refs., 8 figs., 2 tabs

  2. Precipitation of Kr after implantation into Al

    International Nuclear Information System (INIS)

    Birtcher, R.C.; Jaeger, W.

    1985-09-01

    Transmission electron microscopy (TEM) was used to perform a systematic study of the microstructural evolution in Al as a function of the fluence received during 65 keV Kr + ion implantation at room temperature. At the lower fluences (2 x 10 16 to 2 x 10 19 Kr + m -2 ), isolated dislocation loops and the evolution of a dislocation network was observed by TEM. Above fluences of 10 19 Kr + m -2 , the microstructure is dominated by a high density of Kr bubbles whose average size increases with dose. The appearance of additional electron diffraction reflections indicates that the majority of the bubbles contain solid fcc Kr that is epitaxially aligned with the fcc Al matrix. Above fluences of 2 x 10 20 Kr + m -2 an increasing fraction of the Kr is in a liquid or gas-like phase. The thermal stability of the microstructure, characteristic of the different fluence regimes, was investigated up to 640 0 C by in situ TEM annealing experiments

  3. A MOSSBAUER STUDY ON SOLID KRYPTON PRECIPITATES IN ALUMINUM

    NARCIS (Netherlands)

    GREUTER, MJW; NIESEN, L

    1993-01-01

    Mossbauer spectroscopy on the 9.40 keV transition Kr-83 is used to obtain information about solid Kr precipitates in Al. Three different (RbI)-Rb-83 sources differing in water content were used, which, when measured against a solid Kr absorber, show a quadrupole component in addition to a dominating

  4. Picosecond KrF laser interaction with solid targets

    International Nuclear Information System (INIS)

    Smith, R.A.; Barrow, V.; Edwards, J.; Kiehn, G.; Wark, J.; Willi, O.; Barr, J.; Everall, N.; Hooker, C.; Ross, T.; Shaw, M.; Turcu, E.

    1988-01-01

    The recently developed high power KrF system at the Rutherford Appleton Laboratory has been used to heat solid targets with laser energies of up to 1 Joule in 3ps. Single shot irradiances of up to 10 17 Wcm -2 were achieved at the target surface. A number of diagnostics were used to investigate the plasmas produced. These included time integrated and time resolved X-ray and VUV spectroscopy. The plasma temperature was obtained from X-ray line ratios, and the plasma density from Stark broadening. When ASE background containing about 20% of the short pulse energy in a 10ns interval was present, the X0ray spectra indicated an electron temperature of about 400ev and a density of a few times 10 22 cm -2 . If however the prepulse level was kept to below 10 -3 of the main pulse, measurements indicated a plasmas with temperatures of 400ev at close to solid density. The production of hot electrons was investigated using titanium targets overcoated with CH, and observing the Ti Κα emission. These measurements also confirmed the low prepulse level, since Κα emission was weak when only 0.5 microns of plastic overcoat was used. These experimental results were simulated and observations and simulations are discussed

  5. Mixed municipal solid waste (MSW) treatment in Waste centre Spodnji Stari Grad, Krško

    OpenAIRE

    Kortnik, Jože; Leskovar, Jože

    2015-01-01

    Review paper Received: October 25, 2013 Accepted: November 7, 2013 Mixed municipal solid waste (MSW) treatment in Waste centre Spodnji Stari Grad, Krško Ravnanje z mešanimi komunalnimi odpadki v Zbirnem centru Spodnji Stari Grad, Krško Jože Kortnik1'*, Jože Leskovar2 University of Ljubljana, Faculty of Natural Sciences and Engineering, Department of Mining and Geotechnology, Aškerčeva 12, 1000 Ljubljana, Slovenia 2Kostak, d. d., Leskovška cesta 2a, 8270 Krško, Slovenia Correspo...

  6. Phase transitions in solid Kr-CH4 solutions and rotational excitations in phase II

    International Nuclear Information System (INIS)

    Bagatskii, M.I.; Mashchenko, D.A.; Dudkin, V.V.

    2007-01-01

    The heat capacity C p of solid Kr-n CH 4 solutions with the CH 4 concentrations n=0.82, 0.86, 0.90 as well as solutions with n=0.90, 0.95 doped with 0.002 O 2 impurity has been investigated under equilibrium vapor pressure over the internal 1-24 K. The (T,n)-phase diagram was refined and the region of two-phase states was determined for Kr-n CH 4 solid solutions. The contribution of the rotational subsystem, C r ot, to the heat capacity of the solutions has been separated. Analysis of C r ot(T) at T 1 and E 2 between the tunnel levels of the A-, T- and A-, E--nuclear-spin species of CH 4 molecules in the orientationally ordered subsystem, and to determine the effective energy gaps E 1 between lowest levels of the A- and T- species. The relations τ(n) and E 1 (n) stem from changes of the effective potential field caused as the replacement of CH 4 molecules by Kr atoms at sites of the ordered sublattices. The effective gaps E L between a group of tunnel levels of the ground-state liberation state and the nearest group of excited levels of the liberation state of the ordered CH 4 molecules in the solutions with n=0.90 (E L =52 K) and 0.95 (E L =55 K) has been estimated

  7. Characterization of Uranium Solids Precipitated with Aluminosilicates

    International Nuclear Information System (INIS)

    DUFF, MC

    2004-01-01

    At the Savannah River Site (SRS), the High-Level Waste (HLW) Tank Farms store and process high-level liquid radioactive wastes from the Canyons and recycle water from the Defense Waste Processing Facility. The waste is concentrated using evaporators to minimize the volume of space required for HLW storage. Recently, the 2H Evaporator was shutdown due to the crystallization of sodium aluminosilicate (NAS) solids (such as cancrinite and sodalite) that contained close to 10 weight percent of elementally-enriched uranium (U). Prior to extensive cleaning,the evaporator deposits resided on the evaporator walls and other exposed internal surfaces within the evaporator pot. Our goal is to support the basis for the continued safe operation of SRS evaporators and to gain more information that could be used to help mitigate U accumulation during evaporator operation. To learn more about the interaction between U(VI) and NAS in HLW salt solutions, we performed several fundamental studies to examine the mechanisms of U accumulation with NAS in highly caustic solutions. This larger group of studies focused on the following processes: co-precipitation/structural incorporation, sorption, and precipitation (with or without NAS), which will be reviewed in this presentation. We will present and discuss local atomic structural characterization data about U that has been co-precipitated with NAS solids (such as amorphous zeolite precursor material and sodalite) using X-ray absorption fine-structure (XAFS) spectroscopic techniques

  8. A Thermodynamic Mixed-Solid Asphaltene Precipitation Model

    DEFF Research Database (Denmark)

    Lindeloff, Niels; Heidemann, R.A.; Andersen, Simon Ivar

    1998-01-01

    A simple model for the prediction of asphaltene precipitation is proposed. The model is based on an equation of state and uses standard thermodynamics, thus assuming that the precipitation phenomenon is a reversible process. The solid phase is treated as an ideal multicomponent mixture. An activity...

  9. Radiation induced homogeneous precipitation in undersaturated solid-solutions

    International Nuclear Information System (INIS)

    Cauvin, Richard; Martin, Georges.

    1978-01-01

    The stability of various types of solid solutions under irradiation is studied. In this paper, observations made on AlZn solid solutions under 1 MeV electron irradiation are reported. Al-Zn was chosen as a prototype of solid solutions with a simple miscibility gap. It is shown that under appropriate irradiation conditions undersaturated AnZn solid solutions give rise to a homogeneous precipitation of coherent G.P. zones and of incoherent Zn precipitates the atomic volume of which is smaller than that of the matrix. We propose a more general treatment of solute concentration heterogeneities in solid solutions under irradiation and suggest how it might account for the nucleation of the observed phases. The growth of the observed precipitates is studied

  10. Vapor equilibrium data for the systems Ar--N/sub 2/, Kr--Ar, Kr--N/sub 2/, and Xe--Kr, as well as the liquidus lines of solid xenon and of solid krypton in liquid air component mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Mastera, S J

    1977-01-15

    The knowledge of vapor-liquid equilibrium data of real gas mixtures makes possible a precise design of a low temperature distillation system. The noble gas isotopes Kr and Xe are formed as a result of nuclear fission. They reach the off-gas, where they must be separated by cryogenic methods, among others, in order to reduce radiological contamination of the environment. Consequently, an equilibrium apparatus was constructed inhouse, which worked according to a dynamical measurement method. The following low temperature measurements were performed with this apparatus: (1) to test the apparatus with the Ar--N/sub 2/ system, at temperatures of 80, 85, 90, 95, and 100 degrees K; (2) with the Kr--Ar system, at temperatures of 115, 116.5, 120, and 125 degrees K; (3) with the Kr--N/sub 2/ system, at temperatures of 100, 105, at 110 degrees K in the N/sub 2/-rich existence range of the liquid phase above the solubility limit, and at temperatures of 115, 120, and 125 degrees K in the entire concentration range. No data at all were previously known about this important system. (4) In the Xe-Kr system, at temperatures of 150, 155, and 160 degrees K, in the Kr-rich liquid existence range above the solubility limit, and at the temperature steps 165, 166, and 170 degrees in the entire concentration range. The consistency of the equilibrium data thus determined was tested with the computer program SYMFIT. These measurements were completed by determining the solubility limits (= liquidus lines) of solid Kr in a liquid Kr--Ar mixture or in a liquid Kr--N/sub 2/ mixture, as well as the solubility limit of solid Xe in a liquid Xe--Kr mixture. The measurement points for the liquidus lines were associated with the respective pressure and respective temperature over the entire concentration range. The experimentally determined data are displayed on tables and graphs. The utilized measurement equipment, with its glass equilibrium cell, is described.

  11. Mixing and solid suspension in a stirred precipitator

    International Nuclear Information System (INIS)

    Chang, T.P.

    1986-04-01

    Full-scale mixing and solid suspension studies have been conducted to determine the optimum agitator design for precipitators used in plutonium processing. Design considerations include the geometry of precipitator vessels, feed locations, flow patterns, and product requirements. Evaluations of various agitator designs are based on their capabilities: (1) to achieve uniform mixing of reactants in minimum time, (2) to suspend slurry uniformly throughout the vessel, and (3) to minimize power consumption without inducing air entrainment. Tests of full-scale agitator designs showed that significant improvements in mixing, solid suspension, and energy consumption were achieved

  12. Wax Precipitation Modeled with Many Mixed Solid Phases

    DEFF Research Database (Denmark)

    Heidemann, Robert A.; Madsen, Jesper; Stenby, Erling Halfdan

    2005-01-01

    The behavior of the Coutinho UNIQUAC model for solid wax phases has been examined. The model can produce as many mixed solid phases as the number of waxy components. In binary mixtures, the solid rich in the lighter component contains little of the heavier component but the second phase shows sub......-temperature and low-temperature forms, are pure. Model calculations compare well with the data of Pauly et al. for C18 to C30 waxes precipitating from n-decane solutions. (C) 2004 American Institute of Chemical Engineers....

  13. Radiation induced homogeneous precipitation in undersaturated solid-solutions

    International Nuclear Information System (INIS)

    Cauvin, R.; Martin, G.

    1979-01-01

    A TEM study of 1 MeV electron irradiated Al 1.9 at% Zn solid solution shows that Zn precipitates form, under irradiation at temperatures well above the Zn solvus temperature outside irradiation. The corresponding upward shift of this temperature is dose rate dependent. This new example of radiation-induced precipitation exhibits unexpected features, which are not accounted for by the available models: (1) no correlation exists between the location of the precipitates and that of the point defects sinks; (2) the precipitation of incoherent β-phase with atomic volume smaller than that of the matrix, and of coherent G.P. zones both occurs; (3) the size of the coherent β precipitates saturates at large dose. A general mechanism for solute concentration fluctuations under irradiation is proposed which qualitatively accounts for the formation of coherent G.P. zones and for the nucleation of solute clusters with more complex structures. A reanalysis of Russell's model (1977) for the growth of incoherent precipitates shows that it may qualitatively account for the observed behavior of the β phase precipitates. (Auth.)

  14. Plasma conditions generated by interaction of a high brightness, prepulse free Raman amplified KrF laser pulse with solid targets

    International Nuclear Information System (INIS)

    Riley, D.; Gizzi, L.A.; Khattak, F.Y.; Mackinnon, A.J.; Viana, S.M.; Willi, O.

    1992-01-01

    A high brightness, Raman amplified KrF laser has been used to irradiate solid targets with 12 ps laser pulses at intensities above 10 15 W/cm 2 without the presence of a preformed plasma caused by low level amplified spontaneous emission prepulse. Time-resolved x-ray spectroscopy of the K-shell emission from aluminum was used to infer electron densities in excess of 10 23 cm -3 at temperatures of several hundred electronvolts

  15. Effect of octupole interaction on the rotational motion of rotors in a solid Kr-CD4 solution

    International Nuclear Information System (INIS)

    Dudkin, V V; Bagatskii, M I; Mashchenko, D A

    2007-01-01

    The heat capacity of solid (CD 4 ) n Kr 1-n solutions with CD 4 concentrations n = 0.09, 0.17, 0.25, 0.35 and solutions with n = 0.25 doped with 0.0005, 0.0021 and 0.0123 of O 2 impurity has been investigated at T 0.6-30 K. It is found that the molecular field responsible for a qualitative change in the rotational motion of the rotators increases sharply as the number of nearest neighbours increases from one to three. Below 1.6 K the temperature dependence of the heat capacities of the rotational subsystems of the solutions can be described by a sum of the contributions made by molecules finding themselves in effective weak, moderate and strong molecular fields. The average concentration and the effective energy differences between the ground and the first excited energy levels of the CD 4 molecules in the above mentioned fields have been estimated. It is shown that the considerable changes in the experimental heat capacities of the rotational subsystem normalized to a mole of rotors are mostly due to the changes in the relative concentrations x(n) of the rotors in these molecular fields. Above T = 0.6 K the nuclear-spin A, T and E species of the molecules reach equilibrium distribution within one measurement of the heat capacity. The O 2 impurity is found to produce great influence on the heat capacity of the rotational subsystem in the solution with n = 0.25 and the equilibrium composition of the nuclear-spin species of the molecules

  16. SOLIDS PRECIPITATION EVENT IN MCU CAUSAL ANALYSIS AND RECOMMENDATIONS FROM SOLIDS RECOVERY TEAM

    Energy Technology Data Exchange (ETDEWEB)

    Garrison, A.; Aponte, C.

    2014-08-15

    A process upset occurred in the Modular Caustic-Side Solvent Extraction Unit (MCU) facility on April 6th, 2014. During recovery efforts, a significant amount of solids were found in the Salt Solution Feed Tank (SSFT), Salt Solution Receipt Tanks (SSRTs), two extraction contactors, and scrub contactors. The solids were identified by Savannah River National Laboratory (SRNL) as primarily sodium oxalate and sodium alumina silicate (NAS) with the presence of some aluminum hydroxide. NAS solids have been present in the SSFT since simulant runs during cold chemical startup of MCU in 2007, and have not hindered operations since that time. During the process upset in April 2014, the oxalate solids partially blocked the aqueous outlet of the extraction contactors, causing salt solution to exit through the contactor organic outlet to the scrub contactors with the organic phase. This salt solution overwhelmed the scrub contactors and passed with the organic phase to the strip section of MCU. The partially reversed flow of salt solution resulted in a Strip Effluent (SE) stream that was high in Isopar™ L, pH and sodium. The primary cause of the excessive solids accumulation in the SSRTs and SSFT at MCU is attributed to an increase in the frequency of oxalic acid cleaning of the 512-S primary filter. Agitation in the SSRTs at MCU in response to cold weather likely provided the primary mechanism to transfer the solids to the contactors. Sources of the sodium oxalate solids are attributed to the oxalic acid cleaning solution used to clean the primary filter at the Actinide Removal Process (ARP) filtration at 512-S, as well as precipitation from the salt batch feed, which is at or near oxalate saturation. The Solids Recovery Team was formed to determine the cause of the solids formation and develop recommendations to prevent or mitigate this event in the future. A total of 53 recommendations were generated. These recommendations were organized into 4 focus areas: • Improve

  17. Iseh, KR

    African Journals Online (AJOL)

    Iseh, KR. Vol 7, No 3 (2008) - Articles Pattern Of Epistaxis In Sokoto, Nigeria: A Review Of 72 Cases Abstract PDF · Vol 9, No 1 (2010) - Articles Rhinosinusitis: A retrospective analysis of clinical pattern and outcome in north western Nigeria Abstract PDF. ISSN: 1596-3519. AJOL African Journals Online. HOW TO USE AJOL.

  18. Formation of Copper Sulfide Precipitate in Solid Iron

    Science.gov (United States)

    Urata, Kentaro; Kobayashi, Yoshinao

    The growth rate of copper sulfide precipitates has been measured in low carbon steel samples such as Fe-0.3mass%Cu-0.03mass%S-0.1mass%C and Fe-0.1mass%Cu-0.01mass%S- 0.1mass%C. Heat-treatment of the samples was conducted at 1273, 1423 and 1573 K for 100 s - 14.4 ks for precipitation of copper sulfides and then the samples were observed by a scanning electron microscope and a transmission electron microscope to measure the diameter of copper sulfides precipitated in the samples. The growth rate of copper sulfide has been found to be well described by the Ostwald growth model, as follows: R\

  19. The influence of precipitation temperature on the properties of ceria–zirconia solid solution composites

    International Nuclear Information System (INIS)

    Cui, Yajuan; Fang, Ruimei; Shang, Hongyan; Shi, Zhonghua; Gong, Maochu; Chen, Yaoqiang

    2015-01-01

    Highlights: • The crystallite size of precipitate increases as the precipitation temperature rises. • The stack of large crystallite can form nanoparticles with big pore size. • Big pore sizes are advantageous to improve the thermal stability. • Phase segregation is restricted in CZ solid solution precipitated at 70 °C. • The reducibility and OSC of the solid solution precipitated at 70 °C are improved. - Abstract: The ceria–zirconia composites (CZ) with a Ce/Zr mass ratio of 1/1 were synthesized by a back-titration method, in which the influence of precipitation temperature on the properties of ceria–zirconia precipitates was investigated. The resulting precipitation and mixed oxides at different precipitation temperatures were then characterized by a range of techniques, including textural properties, X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), H 2 -temperature programmed reduction (H 2 -TPR) as well as oxygen storage capacity (OSC) measurement. The results revealed that ceria–zirconia composites were formed as solid solution and such structure is favored of thermostability and texture properties. In particular, the composite CZ-70 synthesized at 70 °C exhibited prominent thermostability with a surface area of 32 m 2 /g as well as a pore volume of 0.15 cc/g after aging treatment at 1000 °C for 5 h. And this was found to be associated with the wider pore size distribution which maybe owed to the formation of large crystal at the primary stage of precipitation. Additionally, the composite CZ-70 showed excellent reduction property and OSC benefiting from stable texture and structure

  20. Precipitation in Al–Mg solid solution prepared by solidification under high pressure

    International Nuclear Information System (INIS)

    Jie, J.C.; Wang, H.W.; Zou, C.M.; Wei, Z.J.; Li, T.J.

    2014-01-01

    The precipitation in Al–Mg solid solution containing 21.6 at.% Mg prepared by solidification under 2 GPa was investigated. The results show that the γ-Al 12 Mg 17 phase is formed and the β′ phase cannot be observed in the solid solution during ageing process. The precipitation of γ and β phases takes place in a non-uniform manner during heating process, i.e. the γ and β phases are first formed in the interdendritic region, which is caused by the inhomogeneous distribution of Mg atoms in the solid solution solidified under high pressure. Peak splitting of X-ray diffraction patterns of Al(Mg) solid solution appears, and then disappears when the samples are aged at 423 K for different times, due to the non-uniform precipitation in Al–Mg solid solution. The direct transformation from the γ to β phase is observed after ageing at 423 K for 24 h. It is considered that the β phase is formed through a peritectoid reaction of α + γ → β which needs the diffusion of Mg atoms across the interface of α/γ phases. - Highlights: • The γ phase is formed and the β′ phase is be observed in Al(Mg) solid solution. • Peak splitting of XRD pattern of Al(Mg) solid solution appears during aged at 150 °C. • The β phase is formed through a peritectoid reaction of α + γ → β

  1. Optical imaging of the boreholes KR29, KR29B, KR30, KR31, KR31B, KR32, KR33 and KR33B, at Olkiluoto 2005

    International Nuclear Information System (INIS)

    Majapuro, J.

    2006-02-01

    Suomen Malmi Oy conducted optical imaging surveys of the boreholes KR29, KR29B, KR30, KR31, KR31B, KR32, KR33 and KR33B at the Olkiluoto site in Eurajoki during June 2005. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and preliminary processing of the images. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality through example images. The raw and processed data are delivered digitally in WellCAD format. The images are also attached to the appendix CD of this report in Adobe Acrobat PDF-format. (orig.)

  2. Polymer-encapsulated carbon capture liquids that tolerate precipitation of solids for increased capacity

    Energy Technology Data Exchange (ETDEWEB)

    Aines, Roger D; Bourcier, William L; Spadaccini, Christopher M; Stolaroff, Joshuah K

    2015-02-03

    A system for carbon dioxide capture from flue gas and other industrial gas sources utilizes microcapsules with very thin polymer shells. The contents of the microcapsules can be liquids or mixtures of liquids and solids. The microcapsules are exposed to the flue gas and other industrial gas and take up carbon dioxide from the flue gas and other industrial gas and eventual precipitate solids in the capsule.

  3. Dendritic morphology observed in the solid-state precipitation in binary alloys

    Energy Technology Data Exchange (ETDEWEB)

    Husain, S.W.; Ahmed, M.S.; Qamar, I. [Dr. A.Q. Khan Research Labs., Rawalpindi (Pakistan)

    1999-06-01

    The precipitation of {gamma}{sub 2} phase in Cu-Al {beta}-phase alloys has been observed to occur in the dendritic morphology. Such morphology is rarely observed in the solid-state transformations. Earlier it was reported that the {gamma} precipitates were formed in the dendritic shape when Cu-Zn {beta}-phase alloys were cooled from high temperature. The characteristics of these two alloy systems have been examined to find the factors promoting the dendritic morphology in the solid-state transformations. Rapid bulk diffusion and fast interfacial reaction kinetics would promote such morphology. The kinetics of atom attachment to the growing interface is expected to be fast when crystallographic similarities exist between the parent phase and the precipitate. The authors have predicted the dendritic morphology in the solid-state precipitation in many binary alloy systems simply based on such crystallographic similarities. These alloys include, in addition to Cu-Al and Cu-Zn, the {beta}-phase alloys in Ag-Li, Ag-Zn, Cu-Ga, Au-Zn, and Ni-Zn systems, {gamma}-phase alloys in Cu-Sn and Ag-Cd systems, and {delta}-phase alloys in Au-Cd system. Of these, the alloys in Ag-Zn, Ni-Zn, Ag-Cd, and Cu-Sn systems were prepared and it was indeed found that the precipitates formed in the dendritic shape.

  4. Solids precipitation in crude oils, gas-to-liquids and their blends

    Science.gov (United States)

    Ramanathan, Karthik

    Gas-to-liquids (GTL) liquids are obtained from syngas by the Fischer-Tropsch synthesis. The blending of GTL liquids produced from natural gas/coal reserves and crude oils is a possibility in the near future for multiple reasons. Solids precipitation is a major problem in pipelines and refineries leading to significant additional operating costs. The effect of the addition of a paraffinic GTL liquid to crude oils on solids precipitation was investigated in this study. A Fourier transform infrared (FT-IR) spectroscopic technique was used to obtain solid-liquid equilibria (SLE) data for the various samples. The SLE of multiple systems of model oils composed of n-alkanes was investigated preliminarily. Blends of a model oil simulating a GTL liquid composition and a crude oil showed that the wax precipitation temperature (WPT) decreased upon blending. Three crude oils from different geographic regions (Alaskan North Slope, Colorado and Venezuela) and a laboratory-produced GTL liquid were used in the preparation of blends with five different concentrations of the GTL liquid. The wax precipitation temperatures of the blends were found to decrease with the increasing addition of the GTL liquid for all the oils. This effect was attributed to the solvent effect of the low molecular weight-paraffinic GTL liquid on the crude oils. The weight percent solid precipitated that was estimated as a function of temperature did not show a uniform trend for the set of crude oils. The asphaltene onset studies done on the blends with near-infrared spectroscopy indicated that the addition of GTL liquid could have a stabilizing effect on the asphaltenes in some oils. Analytical techniques such as distillation, solvent separation, HPLC, GC, and GPC were used to obtain detailed composition data on the samples. Two sets of compositional data with 49 and 86 pseudo-components were used to describe the three crude oils used in the blending work. The wax precipitation was calculated using a

  5. Dissolution and precipitation behavior of ternary solid dispersions of ezetimibe in biorelevant media.

    Science.gov (United States)

    Alhayali, Amani; Tavellin, Staffan; Velaga, Sitaram

    2017-01-01

    The effects of different formulations and processes on inducing and maintaining the supersaturation of ternary solid dispersions of ezetimibe (EZ) in two biorelevant media fasted-state simulated intestinal fluid (FaSSIF) and fasted-state simulated gastric fluid (FaSSGF) at different temperatures (25 °C and 37 °C) were investigated in this work. Ternary solid dispersions of EZ were prepared by adding polymer PVP-K30 and surfactant poloxamer 188 using melt-quenching and spray-drying methods. The resulting solid dispersions were characterized using scanning electron microscopy, differential scanning calorimetry (DSC), modulated DSC, powder X-ray diffraction and Fourier transformation infrared spectroscopy. The dissolution of all the ternary solid dispersions was tested in vitro under non-sink conditions. All the prepared solid dispersions were amorphous in nature. In FaSSIF at 25 °C, the melt-quenched (MQ) solid dispersions of EZ were more soluble than the spray-dried (SD) solid dispersions and supersaturation was maintained. However, at 37 °C, rapid and variable precipitation behavior was observed for all the MQ and SD formulations. In FaSSGF, the melting method resulted in better solubility than the spray-drying method at both temperatures. Ternary solid dispersions show potential for improving solubility and supersaturation. However, powder dissolution experiments of these solid dispersions of EZ at 25 °C may not predict the supersaturation behavior at physiologically relevant temperatures.

  6. Geophysical borehole logging of the boreholes KR30, KR31, KR31b, KR32, KR33, KR33b and KR24 Upper Part, at Olkiluoto 2005

    International Nuclear Information System (INIS)

    Majapuro, J.

    2005-12-01

    Suomen Malmi Oy conducted geophysical borehole logging of the boreholes KR30, KR31, KR31B, KR32, KR33, KR33B and KR24 upper part at the Olkiluoto site in Eurajoki during December 2004, January, February and September 2005. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and processing of the acoustic data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  7. Monitoring measurements by difference flow method during the year 2006, drillholes OL-KR1, KR2, KR4, KR7, KR8, KR10, KR14, KR22, KR22B, KR27 and KR28

    International Nuclear Information System (INIS)

    Vaeisaesvaara, J.; Poellaenen, J.; Sokolnicki, M.

    2008-04-01

    The Posiva Flow Log/Difference Flow Method can be used for a relatively fast determination of water conductivity and hydraulic head in fractures/fractured zones in cored drillholes. In this method, a flow meter with a flow guide is used. This report presents the principles and results of the measurements carried out in drillholes OL-KR1, -KR2, -KR4, -KR7, -KR8, -KR10, -KR14, -KR22, -KR22B, -KR27 and -KR28 at the Olkiluoto investigation site during the year 2006. These measurements are a part of the Olkiluoto monitoring programme. Two different section lengths (2 m and 0.5 m) were used in the flow logging measurements. The flow into the drillhole or from the drillhole into the bedrock was measured within the section. Measurements were carried out both in natural conditions and when the drillhole was pumped. The transmissivity (T) and hydraulic head (h) of zones were calculated and are presented in the results. The measurement device also includes a sensor for single-point resistance (SPR) measurements. SPR was always measured in connection with flow measurements. SPR is measured when the tool is moving. The electric conductivity of fracture-specific water (EC) was measured in selected fractures in some of the drillholes. The fractures were chosen on the basis of the measured flow from the fracture to the drillhole. In addition to this some previously selected fractures were measured. The EC of the drillhole water was measured separately. (orig.)

  8. Validation of mechanistic models for gas precipitation in solids during postirradiation annealing experiments

    Science.gov (United States)

    Rest, J.

    1989-12-01

    A number of different phenomenological models for gas precipitation in solids during postirradiation annealing experiments have been proposed. Validation of such mechanistic models for gas release and swelling is complicated by the use of data containing large systematic errors, and phenomena characterized by synergistic effects as well as uncertainties in materials properties. Statistical regression analysis is recommended for the selection of a reasonably well characterized data base for gas release from irradiated fuel under transient heating conditions. It is demonstrated that an appropriate data selection method is required in order to realistically examine the impact of differing descriptions of the phenomena, and uncertainties in selected materials properties, on the validation results. The results of the analysis show that the kinetics of gas precipitation in solids depend on bubble overpressurization effects and need to be accounted for during the heatup phase of isothermal heating experiments. It is shown that if only the total gas release values (as opposed to time-dependent data) were available, differentiation between different gas precipitation models would be ambiguous. The observed sustained increase in the fractional release curve at relatively high temperatures after the total precipitation of intragranular gas in fission gas bubbles is ascribed to the effects of a grain-growth/grain-boundary sweeping mechanism.

  9. Validation of mechanistic models for gas precipitation in solids during postirradiation annealing experiments

    International Nuclear Information System (INIS)

    Rest, J.

    1989-01-01

    A number of different phenomenological models for gas precipitation in solids during postirradiation annealing experiments have been proposed. Validation of such mechanistic models for gas release and swelling is complicated by the use of data containing large systematic errors, and phenomena characterized by synergistic effects as well as uncertainties in materials properties. Statistical regression analysis is recommended for the selection of a reasonably well characterized data base for gas release from irradiated fuel under transient heating conditions. It is demonstrated that an appropriate data selection method is required in order to realistically examine the impact of differing descriptions of the phenomena, and uncertainties in selected materials properties, on the validation results. The results of the analysis show that the kinetics of gas precipitation in solid depend on bubble overpressurization effects and need to be accounted for during the heatup phase of isothermal heating experiments. It is shown that if only the total gas release values (as opposed to time-dependent data) were available, differentiation between different gas precipitation models would be ambiguous. The observed sustained increase in the fractional release curve at relatively high temperatures after the total precipitation of intragranular gas in fission gas bubbles is ascribed to the effects of a grain-growth/grain-boundary sweeping mechanism. (orig.)

  10. Behavior of fission gases in nuclear fuel: XAS characterization of Kr in UO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Martin, P.M., E-mail: Philippe-m.martin@cea.fr [CEA, DEN, Cadarache DEC/SESC, F-13108 St-Paul-Lez-Durance Cedex (France); Vathonne, E.; Carlot, G.; Delorme, R.; Sabathier, C.; Freyss, M.; Garcia, P.; Bertolus, M. [CEA, DEN, Cadarache DEC/SESC, F-13108 St-Paul-Lez-Durance Cedex (France); Glatzel, P. [European Synchrotron Radiation Facility, 6 Rue Jules Horowitz, 38043 Grenoble (France); Proux, O. [OSUG, Observatoire des Sciences de l’Univers de Grenoble, CNRS and Université Joseph Fourier, BP 53, 38041 Grenoble Cedex 9 (France)

    2015-11-15

    X-ray Absorption Spectroscopy (XAS) was used to study the behavior of krypton as a function of its concentration in UO{sub 2} samples implanted with Kr ions. For a 0.5 at.% krypton local concentration, by combining XAS results and DFT + U calculations, we show that without any thermal treatment Kr atoms are mainly incorporated in the UO{sub 2} lattice as single atoms inside a neutral bound Schottky defect with O vacancies aligned along the (100) direction (BSD1). A thermal treatment at 1273 K induces the precipitation of dense Kr nano-aggregates, most probably solid at room temperature. In addition, 26 ± 2% of the Kr atoms remain inside BSD1 showing that Kr-BSD1 complex is stable up to this temperature. Consequently, the (in-)solubility of krypton in UO{sub 2} has to be re-evaluated. For high Kr concentration (8 at.%), XAS signals show that Kr atoms have precipitated in nanometer-sized aggregates with internal densities ranging between 4.15(7) g cm{sup −3} and 3.98(5) g cm{sup −3} even after annealing at 873 K. By neglecting the effect due to the UO{sub 2} matrix, the corresponding krypton pressures at 300 K were equal to 2.6(3) GPa and 2.0(2) GPa, respectively. After annealing at 1673 K, regardless of the initial Kr concentration, a bi-modal distribution is observed with solid nano-aggregates even at room temperature and larger cavities only partially filled with Kr. These results are very close to those observed in UO{sub 2} fuel irradiated in reactor. In this study we show that a rare gas can be used as a probe to investigate the defect creation and their stability in UO{sub 2}.

  11. Polymer⁻Surfactant System Based Amorphous Solid Dispersion: Precipitation Inhibition and Bioavailability Enhancement of Itraconazole.

    Science.gov (United States)

    Feng, Disang; Peng, Tingting; Huang, Zhengwei; Singh, Vikramjeet; Shi, Yin; Wen, Ting; Lu, Ming; Quan, Guilan; Pan, Xin; Wu, Chuanbin

    2018-04-24

    The rapid release of poorly water-soluble drugs from amorphous solid dispersion (ASD) is often associated with the generation of supersaturated solution, which provides a strong driving force for precipitation and results in reduced absorption. Precipitation inhibitors, such as polymers and surfactants, are usually used to stabilize the supersaturated solution by blocking the way of kinetic or thermodynamic crystal growth. To evaluate the combined effect of polymers and surfactants on maintaining the supersaturated state of itraconazole (ITZ), various surfactants were integrated with enteric polymer hydroxypropyl methylcellulose acetate succinate (HPMC AS) to develop polymer⁻surfactant based solid dispersion. The supersaturation stability was investigated by in vitro supersaturation dissolution test and nucleation induction time measurement. Compared to the ASD prepared with HPMC AS alone, the addition of d-alpha-tocopheryl polyethylene glycol 1000 succinate (TPGS) exhibited a synergistic effect on precipitation inhibition. The results indicated that the TPGS not only significantly reduced the degree of supersaturation which is the driving force for precipitation, but also provided steric hindrance to delay crystal growth by absorbing onto the surface of small particles. Subsequently, the formulations were evaluated in vivo in beagle dogs. Compared with commercial product Sporanox ® , the formulation prepared with HPMC AS/TPGS exhibited a 1.8-fold increase in the AUC (0⁻24 h) of ITZ and a 1.43-fold increase of hydroxyitraconazole (OH-ITZ) in the plasma. Similarly, the extent of absorption was increased by more than 40% when compared to the formulation prepared with HPMC AS alone. The results of this study demonstrated that the ASD based on polymer⁻surfactant system could obviously inhibit drug precipitation in vitro and in vivo, which provides a new access for the development of ASD for poorly water-soluble drug.

  12. The complex synthesis and solid state chemistry of ceria-lanthana solid solutions prepared via a hexamethylenetetramine precipitation

    International Nuclear Information System (INIS)

    Fleming, P.G.; Holmes, J.D.; Otway, D.J.; Morris, M.A.

    2011-01-01

    Mixed oxide solid solutions are becoming ever more commercially important across a range of applications. However, their synthesis can be problematical. Here, we show that ceria-lanthana solid solutions can be readily prepared via simple precipitation using hexamethylenetetramine. However, the solution chemistry can be complex, which results in the precipitated particles having a complex structure and morphology. Great care must be taken in both the synthesis and characterisation to quantify the complexity of the product. Even very high heat treatments were not able to produce highly homogeneous materials and X-ray diffractions reveals the non-equilibrium form of particles prepared in this way. Unexpected crystal structures are revealed including a new metastable cubic La 2 O 3 phase. - Graphical abstract: The suggested mechanism for the formation of dual fluorite phase particles, where Step 1 corresponds to room temperature aging, Step 2; heating the solution to 90 deg. C, Step 3; cooling of the solution to room temperature, Step 4; calcination to 500 deg. C, Step 5; calcination to 700 deg. C and Step 6; calcination to 1300 deg. C. The terminology of e.g. La 1-x Ce x (OH) 3 is used to indicate the formation of a mixed oxy-hydroxy participate rather than a definitive assignment of stoichiometry. Similarly, La 1-y Ce y O 2 only implies a mixed solid solution. Highlights: → Mol% of prepared Ce-La oxides did not follow that of reactant mol%. → Complex reaction pathway found to be dependent on metal solution concentrations. → At certain concentrations core shell particles were found to form. → A reaction model was produced based on cationic solubility. → Report lanthana solubility higher than previously reported in CeO 2 .

  13. Precipitation of Nd-Ca carbonate solid solution at 25 degrees C

    International Nuclear Information System (INIS)

    Carroll, S.A.

    1993-01-01

    The formation of a Nd-Ca carbonate solid solution was studied by monitoring the reactions of calcite with aqueous Nd, orthorhombic NdOHCO 3 (s) with aqueous Ca, and calcite with hexagonal Nd-carbonate solid phase as a function of time at 25 degrees C and controlled pCO 2 (g). All experiments reached steady state after 200 h of reaction. The dominant mechanism controlling the formation of the solid solution was precipitation of a Nd-Ca carbonate phase from the bulk solution as individual crystals or at the orthorhombic NdOHCO 3 (s)-solution interface. The lack of Nd adsorption or solid solution at the calcite-solution interface suggests that the solid solution was orthorhombic and may be modeled as a mixture of orthorhombic NdOHCO 3 (s) and aragonite. Orthorhombic NdOHCO 3 (s) was determined to be the stable Nd-carbonate phase in the Nd-CO 2 -H 2 O system at pCO 2 (g) 0.1 atmospheres at 25 degrees C. The equilibrium constant corrected to zero ionic strength for orthorhombic NdOHCO 3 (s) solubility is 10 10.41(±0.29) for the following: NdOHCO 3 (s) + 3H + = Nd 3+ + CO 2 (g) + H 2 O. Results are discussed in relation to radioactive waste disposal by burial, and specifically in relation to americium chemistry

  14. Kinetics of the isothermal decomposition of zirconium hydride: terminal solid solubility for precipitation and dissolution

    Science.gov (United States)

    Denisov, E. A.; Kompaniets, T. N.; Voyt, A. P.

    2018-05-01

    The hydrogen permeation technique in the surface-limited regime (SLR) was first used to study the isothermal decomposition of zirconium hydride. It is shown that under isothermal conditions, the hydrogen terminal solid solubility in the α-phase for hydride precipitation (TSSp) and dissolution (TSSd) differ only by 6%, in contrast to the 20-30% indicated in the available literature. It is demonstrated that even the minimum heating/cooling rate (1 C/min) used in the traditional methods of studying TSSp and TSSd is too high to exclude the effect of kinetics on the results obtained.

  15. Geophysical borehole logging of the boreholes KR30, KR31, KR31b, KR32, KR33, KR33b and KR24 Upper Part, at Olkiluoto 2005

    Energy Technology Data Exchange (ETDEWEB)

    Majapuro, J. [Suomen Malmi Oy, Espoo (Finland)

    2005-12-15

    Suomen Malmi Oy conducted geophysical borehole logging of the boreholes KR30, KR31, KR31B, KR32, KR33, KR33B and KR24 upper part at the Olkiluoto site in Eurajoki during December 2004, January, February and September 2005. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and processing of the acoustic data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  16. Double crystal X-ray analysis of phosphorus precipitation in supersaturated Si-P solid solutions

    International Nuclear Information System (INIS)

    Servidori, M.; Zini, Q.; Dal Monte, C.

    1983-01-01

    The physical nature of the electrically inactive phosphorus in silicon is investigated by double crystal X-ray diffraction measurements. This analysis is performed on laser annealed supersaturated samples, doped by ion implantation up to 5 x 10 21 cm -3 . After isothermal heat treatments, these solid solutions show marked reductions in the electrically active phosphorus concentration. In particular, 850 0 C heatings give rise to a carrier concentration which corresponds to the phosphorus solubility in equilibrium with the inactive dopant. This dopant is characterized by means of lattice strain measurements: they are found consistent with the presence of perfectly coherent cubic SiP precipitates. This result is in agreement with the one obtained in preceeding works by electrical measurements and transmission electron microscopy observations and contradicts the hypothesis that the excess dopant atoms are, at least in part, charged point defects (E-centres). (author)

  17. Photoresonance anode plasma production by KrF lasers

    International Nuclear Information System (INIS)

    Knyazev, B.A.; Melnikov, P.I.; Doroshkin, A.A.; Matveenko, A.N.; Bluhm, H.

    1996-01-01

    The interaction of an intense KrF laser pulse with vapor clouds of different elemental composition has been studied experimentally. The clouds were produced by evaporation of solid targets with a ruby laser. Ionization of the expanding clouds by a KrF laser was observed for clouds containing tantalum atoms. (author). 5 figs., 7 refs

  18. New experimental stopping power data of 4He, 16O, 40Ar, 48Ca and 84Kr projectiles in different solid materials

    Science.gov (United States)

    Trzaska, W. H.; Knyazheva, G. N.; Perkowski, J.; Andrzejewski, J.; Khlebnikov, S. V.; Kozulin, E. M.; Malkiewicz, T.; Mutterer, M.; Savelieva, E. O.

    2018-03-01

    New experimental data on energy loss of 4He, 16O, 40Ar, 48Ca and 84Kr ions in thin, self-supporting foils of C, Al, Ni, Ag, Lu, Au, Pb and Th are presented. The measurements, using the TOF-E method, were done in a very broad energy range around the stopping power maximum; typically from 0.1 to 11 MeV/u. When available, the extracted stopping power values are compared with the previously published data. The overall agreement is good although a fair comparison is difficult as the covered energy range is much larger than in previous measurements. The small error bars and a broad coverage allowed us to test the predictions of theoretical codes: PASS, CasP, and semi-empirical programs: SRIM, LET, MSTAR, and the Hubert table predictions. The deviations of PASS predictions from the experimental data do not exceed 20% for all the measured combinations. CasP predictions are within 15% from the data for heavier ions but diverge up to 40% for lighter ions. Semi-empirical approaches, including SRIM, deviate from the experimental data by less than 5% for the regions already covered by previous experiments but err by about 10-20% for the ion/target combinations that were not measured before: Ca in Lu as well as Kr in Lu, Pb, and Th.

  19. Analytical method of Kr-85 determination, using cryogenic concentration and separation and liquid scintillation counting

    International Nuclear Information System (INIS)

    Heras Iniquez, M.C.; Perez Garcia, M.M.; Grau Malonda, A.

    1983-01-01

    The method used in the Laboratory of the JEN for the determination of Kr-85 levels in gaseous effluents of nuclear power and in the atmosphere is described. Samples of air, collected in metallic cylinders, are introduced into a gas-solid chromatographic separation system which resolves Kr from the other air components. The separated Kr ia dissolved in a toluene based scintillation cocktail, and the Kr-85 content is determined by liquid scintillation counting. (Author)

  20. Monitoring the energy scale of KATRIN with conversion electrons of a solid {sup 83m}Kr source as nuclear standard

    Energy Technology Data Exchange (ETDEWEB)

    Schloesser, Klaus [IKP, Karlsruher Institut fuer Technologie (Germany); Collaboration: KATRIN-Collaboration

    2016-07-01

    For KATRIN to be able to achieve the desired sensitivity of 200 meV/c{sup 2} for the effective electron neutrino mass, it is of crucial importance that the energy scale of the main spectrometer (18.6 keV) is under control within +/-60 mV at any given time over the planned measurement time of approximately 5 years. Besides conventional high voltage dividers and high precision volt meters, a nuclear standard will be deployed additionally in a separate spectrometer of MAC-E filter type. The filter electrodes of both spectrometers are connected galvanically. For permanent and continuous monitoring an easy to use ion implanted source containing the noble gas {sup 83m}Kr was developed and qualified for HV monitoring at the ppm level in the 30 kV regime. This talk presents the methods applied and the achievements made.

  1. Absolute Kr I and Kr II transition probabilities

    International Nuclear Information System (INIS)

    Brandt, T.; Helbig, V.; Nick, K.P.

    1982-01-01

    Transition probabilities for 11 KrI and 9 KrII lines between 366.5 and 599.3nm were obtained from measurements with a wall-stabilised arc at atmospheric pressure in pure krypton. The population densities of the excited krypton levels were calculated under the assumption of LTE from electron densities measured by laser interferometry. The uncertainties for the KrI and the KrII data are 15 and 25% respectively. (author)

  2. Self-aligned nanocrystalline ZnO hexagons by facile solid-state and co-precipitation route

    International Nuclear Information System (INIS)

    Thorat, J. H.; Kanade, K. G.; Nikam, L. K.; Chaudhari, P. D.; Panmand, R. P.; Kale, B. B.

    2012-01-01

    In this study, we report the synthesis of well-aligned nanocrystalline hexagonal zinc oxide (ZnO) nanoparticles by facile solid-state and co-precipitation method. The co-precipitation reactions were performed using aqueous and ethylene glycol (EG) medium using zinc acetate and adipic acid to obtain zinc adipate and further decomposition at 450 °C to confer nanocrystalline ZnO hexagons. XRD shows the hexagonal wurtzite structure of the ZnO. Thermal study reveals complete formation of ZnO at 430 °C in case of solid-state method, whereas in case of co-precipitation method complete formation was observed at 400 °C. Field emission scanning electron microscope shows spherical morphology for ZnO synthesized by solid-state method. The aqueous-mediated ZnO by co-precipitation method shows rod-like morphology. These rods are formed via self assembling of spherical nanoparticles, however, uniformly dispersed spherical crystallites were seen in EG-mediated ZnO. Transmission electron microscope (TEM) investigations clearly show well aligned and highly crystalline transparent and thin hexagonal ZnO. The particle size was measured using TEM and was observed to be 50–60 nm in case of solid-state method and aqueous-mediated co-precipitation method, while 25–50 nm in case of EG-mediated co-precipitation method. UV absorption spectra showed sharp absorption peaks with a blue shift for EG-mediated ZnO, which demonstrate the mono-dispersed lower particle size. The band gap of the ZnO was observed to be 3.4 eV which is higher than the bulk, implies nanocrystalline nature of the ZnO. The photoluminescence studies clearly indicate the strong violet and weak blue emission in ZnO nanoparticles which is quite unique. The process investigated may be useful to synthesize other oxide semiconductors and transition metal oxides.

  3. Self-aligned nanocrystalline ZnO hexagons by facile solid-state and co-precipitation route

    Energy Technology Data Exchange (ETDEWEB)

    Thorat, J. H. [Mahatma Phule College, Department of Chemistry (India); Kanade, K. G. [Annasaheb Awate College (India); Nikam, L. K. [B.G. College (India); Chaudhari, P. D.; Panmand, R. P.; Kale, B. B., E-mail: kbbb1@yahoo.com [Center for Materials for Electronics Technology (C-MET) (India)

    2012-02-15

    In this study, we report the synthesis of well-aligned nanocrystalline hexagonal zinc oxide (ZnO) nanoparticles by facile solid-state and co-precipitation method. The co-precipitation reactions were performed using aqueous and ethylene glycol (EG) medium using zinc acetate and adipic acid to obtain zinc adipate and further decomposition at 450 Degree-Sign C to confer nanocrystalline ZnO hexagons. XRD shows the hexagonal wurtzite structure of the ZnO. Thermal study reveals complete formation of ZnO at 430 Degree-Sign C in case of solid-state method, whereas in case of co-precipitation method complete formation was observed at 400 Degree-Sign C. Field emission scanning electron microscope shows spherical morphology for ZnO synthesized by solid-state method. The aqueous-mediated ZnO by co-precipitation method shows rod-like morphology. These rods are formed via self assembling of spherical nanoparticles, however, uniformly dispersed spherical crystallites were seen in EG-mediated ZnO. Transmission electron microscope (TEM) investigations clearly show well aligned and highly crystalline transparent and thin hexagonal ZnO. The particle size was measured using TEM and was observed to be 50-60 nm in case of solid-state method and aqueous-mediated co-precipitation method, while 25-50 nm in case of EG-mediated co-precipitation method. UV absorption spectra showed sharp absorption peaks with a blue shift for EG-mediated ZnO, which demonstrate the mono-dispersed lower particle size. The band gap of the ZnO was observed to be 3.4 eV which is higher than the bulk, implies nanocrystalline nature of the ZnO. The photoluminescence studies clearly indicate the strong violet and weak blue emission in ZnO nanoparticles which is quite unique. The process investigated may be useful to synthesize other oxide semiconductors and transition metal oxides.

  4. Coarsening of Ni-Ge solid-solution precipitates in 'inverse' Ni{sub 3}Ge alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ardell, Alan J., E-mail: alan.ardell@gmail.com [National Science Foundation, 4201 Wilson Boulevard, Arlington, VA 22230 (United States); Ma Yong [Aquatic Sensor Network Technology LLC, Storrs, CT 06268 (United States)

    2012-07-30

    Highlights: Black-Right-Pointing-Pointer We report microstructural evolution of disordered Ni-Ge precipitates in Ni{sub 3}Ge alloys. Black-Right-Pointing-Pointer Coarsening kinetics and particle size distributions are presented. Black-Right-Pointing-Pointer Data are analyzed quantitatively using the MSLW theory, but agreement is only fair. Black-Right-Pointing-Pointer The shapes of large precipitates are unusual, with discus or boomerang cross-sections. Black-Right-Pointing-Pointer Results are compared with morphology, kinetics of Ni-Al in inverse Ni{sub 3}Al alloys. - Abstract: The morphological evolution and coarsening kinetics of Ni-Ge solid solution precipitates from supersaturated solutions of hypostoichiometric Ni{sub 3}Ge were investigated in alloys containing from 22.48 to 23.50 at.% Ge at 600, 650 and 700 Degree-Sign C. The particles evolve from spheres to cuboids, though the flat portions of the interfaces are small. At larger sizes the precipitates coalesce into discus shapes, and are sometimes boomerang-shaped in cross section after intersection. The rate constant for coarsening increases strongly with equilibrium volume fraction, much more so than predicted by current theories; this is very different from the coarsening behavior of Ni{sub 3}Ge precipitates in normal Ni-Ge alloys and of Ni-Al precipitates in inverse Ni{sub 3}Al alloys. The activation energy for coarsening, 275.86 {+-} 24.17 kJ/mol, is somewhat larger than the result from conventional diffusion experiments, though within the limits of experimental error. Quantitative agreement between theory and experiment, estimated using available data on tracer diffusion coefficients in Ni{sub 3}Ge, is fair, the calculated rate constants exceeding measured ones by a factor of about 15. The particle size distributions are not in very good agreement with the predictions of any theory. These results are discussed in the context of recent theories and observations.

  5. Coarsening of Ni–Ge solid-solution precipitates in “inverse” Ni3Ge alloys

    International Nuclear Information System (INIS)

    Ardell, Alan J.; Ma Yong

    2012-01-01

    Highlights: ► We report microstructural evolution of disordered Ni–Ge precipitates in Ni 3 Ge alloys. ► Coarsening kinetics and particle size distributions are presented. ► Data are analyzed quantitatively using the MSLW theory, but agreement is only fair. ► The shapes of large precipitates are unusual, with discus or boomerang cross-sections. ► Results are compared with morphology, kinetics of Ni–Al in inverse Ni 3 Al alloys. - Abstract: The morphological evolution and coarsening kinetics of Ni–Ge solid solution precipitates from supersaturated solutions of hypostoichiometric Ni 3 Ge were investigated in alloys containing from 22.48 to 23.50 at.% Ge at 600, 650 and 700 °C. The particles evolve from spheres to cuboids, though the flat portions of the interfaces are small. At larger sizes the precipitates coalesce into discus shapes, and are sometimes boomerang-shaped in cross section after intersection. The rate constant for coarsening increases strongly with equilibrium volume fraction, much more so than predicted by current theories; this is very different from the coarsening behavior of Ni 3 Ge precipitates in normal Ni–Ge alloys and of Ni–Al precipitates in inverse Ni 3 Al alloys. The activation energy for coarsening, 275.86 ± 24.17 kJ/mol, is somewhat larger than the result from conventional diffusion experiments, though within the limits of experimental error. Quantitative agreement between theory and experiment, estimated using available data on tracer diffusion coefficients in Ni 3 Ge, is fair, the calculated rate constants exceeding measured ones by a factor of about 15. The particle size distributions are not in very good agreement with the predictions of any theory. These results are discussed in the context of recent theories and observations.

  6. Alt koster 10 kr

    DEFF Research Database (Denmark)

    Ejersbo, Lisser Rye

    2014-01-01

    Jeg havde engang en elev, som fortalte, at når han gik i byen for at købe ind, så var det nemt at beregne, om han havde nok penge med i byen. Han sagde bare, at alle varerne kun kostede 10 kr. Det kan lyde som lidt af en tilsnigelse, så klassen og jeg besluttede at undersøge om hans metode virkede....

  7. Analytical method of Kr-85 determination, using cryogenic concentration and separation and liquid scintillation counting; Desarrollo del metodo de concentracion y se paracion criogenica cromatografica y medida radiactiva por centelleo liquido de Kr-85

    Energy Technology Data Exchange (ETDEWEB)

    Heras, M C; Perez, M M; Grau, A

    1983-07-01

    The method used in the Laboratory of the JEN for the determination of Kr-85 levels in gaseous effluents of nuclear power and in the atmosphere is described. Samples of air, collected in metallic cylinders, are introduced into a gas-solid chromatographic separation system which resolves Kr from the other air components. The separated Kr ia dissolved in a toluene based scintillation cocktail, and the Kr-85 content is determined by liquid scintillation counting. (Author)

  8. Finite element evaluation of elasto-plastic accommodation energies during solid state transformations: Coherent, spherical precipitate in finite matrix

    International Nuclear Information System (INIS)

    Sen, S.; Balasubramaniam, R.; Sethuraman, R.

    1996-01-01

    The molar volume difference between the matrix and the precipitate phases in the case of solid state phase transformations results in the creation of stain energy in the system due to the misfit strains. A finite element model based on the initial strain approach is proposed to evaluate elasto-plastic accommodation energies during solid state transformation. The three-dimensional axisymmetric model has been used to evaluate energies as a function of transformation for α-β hydrogen transformations in the Nb-H system. The transformation has been analyzed for the cases of transformation progressing both from the center to surface and from the surface to center of the system. The effect of plastic deformation has been introduced to make the model realistic, specifically to the Nb-NbH phase transformation which involves a 4% linear misfit strain. It has been observed that plastic deformation reduces the strain energies compared to the linear elastic analysis

  9. Uncertainty in solid precipitation and snow depth prediction for Siberia using the Noah and Noah-MP land surface models

    Science.gov (United States)

    Suzuki, Kazuyoshi; Zupanski, Milija

    2018-01-01

    In this study, we investigate the uncertainties associated with land surface processes in an ensemble predication context. Specifically, we compare the uncertainties produced by a coupled atmosphere-land modeling system with two different land surface models, the Noah- MP land surface model (LSM) and the Noah LSM, by using the Maximum Likelihood Ensemble Filter (MLEF) data assimilation system as a platform for ensemble prediction. We carried out 24-hour prediction simulations in Siberia with 32 ensemble members beginning at 00:00 UTC on 5 March 2013. We then compared the model prediction uncertainty of snow depth and solid precipitation with observation-based research products and evaluated the standard deviation of the ensemble spread. The prediction skill and ensemble spread exhibited high positive correlation for both LSMs, indicating a realistic uncertainty estimation. The inclusion of a multiple snowlayer model in the Noah-MP LSM was beneficial for reducing the uncertainties of snow depth and snow depth change compared to the Noah LSM, but the uncertainty in daily solid precipitation showed minimal difference between the two LSMs. The impact of LSM choice in reducing temperature uncertainty was limited to surface layers of the atmosphere. In summary, we found that the more sophisticated Noah-MP LSM reduces uncertainties associated with land surface processes compared to the Noah LSM. Thus, using prediction models with improved skill implies improved predictability and greater certainty of prediction.

  10. On the modeling of irradiation-induced homogeneous precipitation in proton-bombarded Ni-Si solid solutions

    Science.gov (United States)

    Lam, Nghi Q.; Janghorban, K.; Ardell, A. J.

    1981-10-01

    Irradiation-induced solute redistribution leading to precipitation of coherent γ' particles in undersaturated Ni-based solid solutions containing 6 and 8 at.% Si during 400-keV proton bombardment was modeled, based on the concept of solute segregation in concentrated alloys under spatially-dependent defect production conditions. The combined effects of (i) an extremely large difference between the defect production rates in the peak-damage and mid-range regions during irradiation and (ii) a preferential coupling between the interstitial and solute fluxes generate a net transient flux of Si atoms into the mid-range region, which is much larger than the solute flux out of this location. As a result, the Si concentration exceeds the solubility limit and homogeneous precipitation of the γ' phase occurs in this particular region of the irradiated samples. The spatial, compositional and temperature dependences of irradiation-induced homogeneous precipitation derived from the present theoretical calculations are in good qualitative agreement with experimental observations

  11. Geophysical drillhole logging and optical imaging of the drillholes OL-KR43, OL-KR44, OL-KR44B, OL-KR45, OL-KR45B, OL-KR46, OL-KR46B, OL-KR47, OL-KR47B and OL-KR48, at Olkiluoto 2007 and 2008

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.; Heikkinen, E.

    2008-09-01

    Suomen Malmi Oy conducted geophysical drillhole logging and optical imaging of the drillholes OL-KR43, OL-KR44, OL-KR44B, OL-KR45, OL-KR45B, OL-KR46, OL-KR46B, OL-KR47, OL-KR47B and OL-KR48 at the Olkiluoto site in Eurajoki during December 2007, May 2008. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and data processing. The report describes field operation, equipment as well as processing procedures and shows the obtained results and an analysis of their quality in the appendices. The raw and processed data are delivered digitally in WellCAD, PDF and Excel format. (orig.)

  12. A15 superconductors through direct solid-state precipitation: V/sub 3/Ga and Nb/sub 3/Al

    Energy Technology Data Exchange (ETDEWEB)

    Hong, M.

    1980-09-01

    A solid-state precipitation process was used to prepare superconducting tapes containing an A15 phase, V/sub 3/Ga or Nb/sub 3/Al, in a ductile niobium or vanadium containing BCC matrix. Ingots weighing as large as 30 to 50 gms of V-(14 approx. 19 at. %) Ga and Nb-(13 approx. 22 at. %) Al were prepared by arc-melting, homogenized, quenched, warm-rolled over 99% into tape, and aged at temperatures in the range 600/sup 0/C to 1000/sup 0/C to precipitate the superconducting A15 phase. The features demonstrated by the process are very attractive for practical applications. In the V-Ga system, transmission electron microscopy (TEM) studies revealed the A15 precipitates in an elongated form. However, for the Nb-Al samples, deformed and aged at 750/sup 0/C, TEM studies revealed A15 precipitation in fine equi-axed particles which formed as a semi-continuous network over sub-grain boundaries formed by the recovery of deformation-induced dislocations. In the V-Ga system, the maximum critical transition temperature (approx. 15 K) was found in materials aged at temperatures of 750/sup 0/C or below. At these aging temperatures the T/sub c/ initially increased with aging time and passed through a distinct maximum. The source of the exceptionally high T/sub c/ is discussed. In the Nb-Al system, the aging response of the T/sub c/ of the tested samples was somewhat different; the T/sub c/ increased with aging time to a plateau, and then increased again to a second plateau. The maximum T/sub c/ measured was approx. 17 K. Promising high-field overall critical currents were obtained in the Nb-Al system (overall J/sub c/ approx. 10/sup 4/ A/cm/sup 2/ in a magnetic field of 140 KG at 4.2 K).

  13. 85Kr dating of groundwater

    International Nuclear Information System (INIS)

    Rozanski, K.; Florkowski, T.

    1978-01-01

    The possibility of 85 Kr dating of groundwater is being investigated. The method of gas extraction from 200 to 300 litres of water sample has been developed. The Argon and Krypton mixture, separated from the gas extracted from water, was counted in a 1.5 ml volume proportional counter. The amount of krypton gas in the counter was determined by mass spectrometry. A number of surface and groundwater samples were analyzed indicating an 85 Kr concentration ranging from present atmospheric content (river water) to zero values. 85 Kr 'blank value' was determined to be about 5 per cent of present 85 Kr atmospheric content. For groundwater samples, the mean residence time in the system was calculated assuming the exponential model and known 85 Kr input function. Further improvement of the method should bring higher yield of krypton separation and lower volume of water necessary for analysis. (orig.) [de

  14. Beyond rain: Advances in measurements of solid or mixed phase precipitation using a 2D-Video-Distrometer

    Science.gov (United States)

    Schwinzerl, Martin; Schönhuber, Michael; Lammer, Günter

    2015-04-01

    The requirement to estimate for each individual hydrometeor precipitation parameters such as shape, equi-voluminous diameter, fall velocity, height to width ratio, and canting angle gave rise to the development of the family of 2D-Video-Distrometer (2DVD) measurement devices. The measurement principle of the 2DVD is based upon the ability to acquire a side- and front view onto each particle by virtue of two orthogonally arranged high-speed line-scan cameras. The cameras are displaced vertically towards each other by a precisely determined distance in the ballpark of 6 mm, thus allowing the estimation of the vertical fall velocity in-situ on a per-particle basis. The geometrical and velocity information, sampled over a measurement surface of approx. 100 x 100 mm in this way, is then used to derive observables like rain rate and the accumulated equivalent amount of precipitation with a high degree of statistical relevance. One of the biggest assets of this measurement principle is the ability to perform measurements without relying on any externally provided model or phenomenological relationship between observables like particle shape and velocity. For liquid precipitation in the form of natural rain, this allows for example to verify whether established relationships - like, for example, the tabulated values for diameter vs. vertical velocity provided by Gunn & Kinzer - can be reproduced in sampled datasets. For mixed-phase and solid precipitation, different types of hydrometeors like for example different snow flake families, hail and graupel yield - depending on parameters like for example the water content and therefor, in turn, the density of the particle - very diverse results with respect to expected fall velocity, oblateness, or general shape for a given diameter class. The ability of the 2DVD to capture these parameters directly and without reliance on externally provided relationships, has contributed to the attractiveness of this measurement device for in

  15. Solubility of jarosite solid solutions precipitated from acid mine waters, Iron Mountain, California

    Science.gov (United States)

    Alpers, Charles N.; Nordstrom, D. Kirk; Ball, J.W.

    1989-01-01

    Because of the common occurrence of 15 to 25 mole percent hydronium substitution on the alkali site in jarosites, it is necessary to consider the hydronium content of jarosites in any attempt at rigorous evaluation of jarosite solubility or of the saturation state of natural waters with respect to jarosite. A Gibbs free energy of 3293.5±2.1 kJ mol-1 is recommended for a jarosite solid solution of composition K.77Na.03(H3O).20Fe3(SO4)2(OH)6. Solubility determinations for a wider range of natural and synthetic jarosite solid solutions will be necessary to quantify the binary and ternary mixing parameters in the (K-Na-H3O) system. In the absence of such studies, molar volume data for endmember minerals indicate that the K-H3O substitution in jarosite is probably closer to ideal mixing than either the Na-K or Na-H3O substitution.

  16. pH-Induced precipitation behavior of weakly basic compounds: determination of extent and duration of supersaturation using potentiometric titration and correlation to solid state properties.

    Science.gov (United States)

    Hsieh, Yi-Ling; Ilevbare, Grace A; Van Eerdenbrugh, Bernard; Box, Karl J; Sanchez-Felix, Manuel Vincente; Taylor, Lynne S

    2012-10-01

    To examine the precipitation and supersaturation behavior of ten weak bases in terms of the relationship between pH-concentration-time profiles and the solid state properties of the precipitated material. Initially the compound was dissolved at low pH, followed by titration with base to induce precipitation. Upon precipitation, small aliquots of acid or base were added to induce slight subsaturation and supersaturation respectively and the resultant pH gradient was determined. The concentration of the unionized species was calculated as a function of time and pH using mass and charge balance equations. Two patterns of behavior were observed in terms of the extent and duration of supersaturation arising following an increase in pH and this behavior could be rationalized based on the crystallization tendency of the compound. For compounds that did not readily crystallize, an amorphous precipitate was formed and a prolonged duration of supersaturation was observed. For compounds that precipitated to crystalline forms, the observed supersaturation was short-lived. This study showed that supersaturation behavior has significant correlation with the solid-state properties of the precipitate and that pH-metric titration methods can be utilized to evaluate the supersaturation behavior.

  17. Precipitation of solid phase calcium carbonates and their effect on application of seawater SA–T–P models

    Directory of Open Access Journals (Sweden)

    R. Feistel

    2009-07-01

    Full Text Available At the present time, little is known about how broad salinity and temperature ranges are for seawater thermodynamic models that are functions of absolute salinity (SA, temperature (T and pressure (P. Such models rely on fixed compositional ratios of the major components (e.g., Na/Cl, Mg/Cl, Ca/Cl, SO4/Cl, etc.. As seawater evaporates or freezes, solid phases [e.g., CaCO3(s or CaSO42H2O(s] will eventually precipitate. This will change the compositional ratios, and these salinity models will no longer be applicable. A future complicating factor is the lowering of seawater pH as the atmospheric partial pressures of CO2 increase. A geochemical model (FREZCHEM was used to quantify the SA−T boundaries at P=0.1 MPa and the range of these boundaries for future atmospheric CO2 increases. An omega supersaturation model for CaCO3 minerals based on pseudo-homogeneous nucleation was extended from 25–40°C to 3°C. CaCO3 minerals were the boundary defining minerals (first to precipitate between 3°C (at SA=104 g kg− and 40°C (at SA=66 g kg−. At 2.82°C, calcite(CaCO3 transitioned to ikaite(CaCO36H2O as the dominant boundary defining mineral for colder temperatures, which culminated in a low temperature boundary of −4.93°C. Increasing atmospheric CO2 from 385 μatm (390 MPa (in Year 2008 to 550 μatm (557 MPa (in Year 2100 would increase the SA and t boundaries as much as 11 g kg−1 and 0.66°C, respectively. The model-calculated calcite-ikaite transition temperature of 2.82°C is in excellent agreement with ikaite formation in natural environments that occurs at temperatures of 3°C or lower. Furthermore, these results provide a quantitative theoretical explanation (FREZCHEM model calculation for why ikaite is the solid phase CaCO3 mineral that precipitates during seawater freezing.

  18. Precipitation of solid phase calcium carbonates and their effect on application of seawater SA-T-P models

    Science.gov (United States)

    Marion, G. M.; Millero, F. J.; Feistel, R.

    2009-07-01

    At the present time, little is known about how broad salinity and temperature ranges are for seawater thermodynamic models that are functions of absolute salinity (SA), temperature (T) and pressure (P). Such models rely on fixed compositional ratios of the major components (e.g., Na/Cl, Mg/Cl, Ca/Cl, SO4/Cl, etc.). As seawater evaporates or freezes, solid phases [e.g., CaCO3(s) or CaSO42H2O(s)] will eventually precipitate. This will change the compositional ratios, and these salinity models will no longer be applicable. A future complicating factor is the lowering of seawater pH as the atmospheric partial pressures of CO2 increase. A geochemical model (FREZCHEM) was used to quantify the SA-T boundaries at P=0.1 MPa and the range of these boundaries for future atmospheric CO2 increases. An omega supersaturation model for CaCO3 minerals based on pseudo-homogeneous nucleation was extended from 25-40°C to 3°C. CaCO3 minerals were the boundary defining minerals (first to precipitate) between 3°C (at SA=104 g kg-) and 40°C (at SA=66 g kg-). At 2.82°C, calcite(CaCO3) transitioned to ikaite(CaCO36H2O) as the dominant boundary defining mineral for colder temperatures, which culminated in a low temperature boundary of -4.93°C. Increasing atmospheric CO2 from 385 μatm (390 MPa) (in Year 2008) to 550 μatm (557 MPa) (in Year 2100) would increase the SA and t boundaries as much as 11 g kg-1 and 0.66°C, respectively. The model-calculated calcite-ikaite transition temperature of 2.82°C is in excellent agreement with ikaite formation in natural environments that occurs at temperatures of 3°C or lower. Furthermore, these results provide a quantitative theoretical explanation (FREZCHEM model calculation) for why ikaite is the solid phase CaCO3 mineral that precipitates during seawater freezing.

  19. Antisolvent Precipitation for the Synthesis of Monodisperse Mesoporous Niobium Oxide Spheres as Highly Effective Solid Acid Catalysts

    KAUST Repository

    Li, Cheng Chao; Dou, Jian; Chen, Luwei; Lin, Jianyi; Zeng, Hua Chun

    2012-01-01

    We have developed a low-cost reaction protocol to synthesize mesoporous Nb 2O 5-based solid acid catalysts with external shape control. In the synthesis, monodisperse glycolated niobium oxide spheres (GNOS) were prepared by means of a simple antisolvent precipitation approach and subsequently converted to mesoporous niobium oxide spheres (MNOS) with a large surface area of 312m 2g -1 by means of the hydrothermal treatment. The antisolvent acetone used to obtain GNOS was recovered through distillation at high purity. The obtained mesoporous MNOS were functionalized further with sulfate anions at different temperatures or incorporated with tungstophosphoric acid to obtain recyclable solid acid catalysts. These MNOS-based catalysts showed excellent performance in a wide range of acid-catalyzed reactions, such as Friedel-Crafts alkylation, esterification, and hydrolysis of acetates. As they are monodisperse spheres with diameters in the submicrometer range, the catalysts can be easily separated and reused. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Antisolvent Precipitation for the Synthesis of Monodisperse Mesoporous Niobium Oxide Spheres as Highly Effective Solid Acid Catalysts

    KAUST Repository

    Li, Cheng Chao

    2012-03-20

    We have developed a low-cost reaction protocol to synthesize mesoporous Nb 2O 5-based solid acid catalysts with external shape control. In the synthesis, monodisperse glycolated niobium oxide spheres (GNOS) were prepared by means of a simple antisolvent precipitation approach and subsequently converted to mesoporous niobium oxide spheres (MNOS) with a large surface area of 312m 2g -1 by means of the hydrothermal treatment. The antisolvent acetone used to obtain GNOS was recovered through distillation at high purity. The obtained mesoporous MNOS were functionalized further with sulfate anions at different temperatures or incorporated with tungstophosphoric acid to obtain recyclable solid acid catalysts. These MNOS-based catalysts showed excellent performance in a wide range of acid-catalyzed reactions, such as Friedel-Crafts alkylation, esterification, and hydrolysis of acetates. As they are monodisperse spheres with diameters in the submicrometer range, the catalysts can be easily separated and reused. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Carbonation of municipal solid waste incineration electrostatic precipitator fly ashes in solution.

    Science.gov (United States)

    De Boom, Aurore; Aubert, Jean-Emmanuel; Degrez, Marc

    2014-05-01

    Carbonation was applied to a Pb- and Zn-contaminated fraction of municipal solid waste incineration electrofilter fly ashes in order to reduce heavy metal leaching. Carbonation tests were performed in solution, by Na2CO3 addition or CO2 bubbling, and were compared with washing (with water only). The injection of CO2 during the washing did not modify the mineralogy, but the addition of Na2CO3 induced the reaction with anhydrite, forming calcite. Microprobe analyses showed that Pb and Zn contamination was rather diffuse and that the various treatments had no effect on Pb and Zn speciation in the residues. The leaching tests indicated that carbonation using Na2CO3 was successful because it gave a residue that could be considered as non-hazardous material. With CO2 bubbling, Pb and Zn leaching was strongly decreased compared with material washed with water alone, but the amount of chromium extracted became higher than the non-hazardous waste limits for landfilling.

  2. Calculation of a complete data set for n + 83Kr, 84Kr, 85Kr and 86Kr in the energy region 0.001-20 MeV

    International Nuclear Information System (INIS)

    Cai Chonghai

    1999-01-01

    Complete reaction cross sections, secondary neutron spectra and elastic scattering angular distributions of 83 Kr, 84 Kr, 85 Kr and 86 Kr in the energy region 0.001-20 MeV are calculated, theoretical results are in ENDF/B-6 in pretty good accordance with experimental data

  3. Optical imaging of the boreholes KR37, KR37B and KR38 at Olkiluoto 2005

    International Nuclear Information System (INIS)

    Majapuro, J.

    2006-02-01

    Suomen Malmi Oy conducted optical imaging surveys of the boreholes KR37, KR37B and KR38 at the Olkiluoto site in Eurajoki during September 2005. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and preliminary processing of the images. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality through example images. The raw and processed data are delivered digitally in WellCAD format. The images are also attached to the appendix CD of this report in Adobe Acrobat PDF-format. (orig.)

  4. Effects of solid fission products forming dissolved oxide (Nd) and metallic precipitate (Ru) on the thermal conductivity of uranium base oxide fuel

    International Nuclear Information System (INIS)

    Kim, Dong-Joo; Yang, Jae-Ho; Kim, Jong-Hun; Rhee, Young-Woo; Kang, Ki-Won; Kim, Keon-Sik; Song, Kun-Woo

    2007-01-01

    The effects of solid fission products on the thermal conductivity of uranium base oxide nuclear fuel were experimentally investigated. Neodymium (Nd) and ruthenium (Ru) were added to represent the physical states of solid fission products such as 'dissolved oxide' and 'metallic precipitate', respectively. Thermal conductivity was determined on the basis of the thermal diffusivity, density and specific heat values. The effects of the additives on the thermal conductivity were quantified in the form of the thermal resistivity equation - the reciprocal of the phonon conduction equation - which was determined from the measured data. It is concluded that the thermal conductivity of the irradiated nuclear fuel is affected by both the 'dissolved oxide' and the 'metallic precipitate', however, the effects are in the opposite direction and the 'dissolved oxide' influences the thermal conductivity more significantly than that of the 'metallic precipitate'

  5. Determinations of the temperature of terminal solid solubility in dissolution and precipitation of hydrogen/deuterium in irradiated Zircaloy-4

    Energy Technology Data Exchange (ETDEWEB)

    Vizcaino, P [CNEA-CONICET, Centro Atomico Ezeiza (Argentina)

    2012-07-01

    The proposed plan is an approach to the metallurgical consequences of the high neutron fluencies (10''2''2 n/cm''2) on the hydrogen behavior in zirconium based alloys, based on the significance of the microstructural behavior of the high burn up fuel claddings during the dry storage period. The studies are focused on Zircaloy-4, concerning to two processes: Neutron irradiation damage; Hydrogen pick up. The Zircaloy-4 was taken from cooling channels of the PHWR Atucha 1. These components remained more than 10 years in service, reaching neutron fluencies up to 10''2''2 n/cm''2. In the last recent years, measurements of the hydride dissolution temperatures have shown that hydrogen solubility is affected by the neutron irradiation, increasing it respect to the unirradiated Zircaloy solubility. In addition, in this material the amorphization/dissolution of the second phase particles (SPPs) was observed, being proposed an interaction between the hydrogen atoms, the SPPs and the irradiation defects as a possible explanation of the observed behavior. For the present case, attention will be focused on the hydride precipitation process, since it is strongly related with delay hydrogen cracking initiation, a problem of direct concern for the dry storage. The goal of the present proposal is to make an approach to the source of the observed effect, applying several specific techniques as differential scanning calorimetry (DSC), high resolution x-ray diffraction and transmission electron microscopy. The objectives can be divided as follows: Determination of the temperatures of terminal solid solubility in dissolution (TTSSd) and in precipitation (TTSSp) in high fluency irradiated Zircaloy-4, reproducing the temperatures at which the Zircaloy fuel claddings remain during dry storage by an annealing program during the DSC experiments; Observations by optical and transmission electron microscopy of the hydride distribution before (as received material) and after high temperature

  6. Supported liquid membrane based removal of lead(II) and cadmium(II) from mixed feed: Conversion to solid waste by precipitation

    Energy Technology Data Exchange (ETDEWEB)

    Bhatluri, Kamal Kumar; Manna, Mriganka Sekhar; Ghoshal, Aloke Kumar; Saha, Prabirkumar, E-mail: p.saha@iitg.ac.in

    2015-12-15

    Highlights: • Simultaneous removal of two heavy metals lead and cadmium. • Conversion of liquid waste to solid precipitation. • Precipitation facilitates the metals transportation through LM. • Solidification of liquid waste minimizes the final removal of waste. - Abstract: Simultaneous removal of two heavy metals, lead(II) and cadmium(II), from mixed feed using supported liquid membrane (SLM) based technique is investigated in this work. The carrier-solvent combination of “sodium salt of Di-2-ethylhexylphosphoric acid (D2EHPA) (4% w/w) in environmentally benign coconut oil” was immobilized into the pores of solid polymeric polyvinylidene fluoride (PVDF) support. Sodium carbonate (Na{sub 2}CO{sub 3}) was used as the stripping agent. Carbonate salts of lead(II) and cadmium(II) were formed in the stripping side interface and they were insoluble in water leading to precipitation inside the stripping solution. The transportation of solute is positively affected due to the precipitation. Lead(II) removal was found to be preferential due to its favorable electronic configuration. The conversion of the liquid waste to the solid one was added advantage for the final removal of hazardous heavy metals.

  7. Recombination of KrD+ and KrH+ ions in afterglow plasma

    International Nuclear Information System (INIS)

    Korolov, I; Kotrik, T; Plasil, R; Hejduk, M; Varju, J; Dohnal, P; Glosik, J

    2009-01-01

    Reported is flowing afterglow (FALP) study of recombination of KrH + and KrD + ions with electrons at 250 K in mixtures of He/Kr/H 2 and He/Kr/D 2 , respectively. The influence of fast recombining cluster ions formation on apparent effective recombination rate coefficients (α eff ) was measured and used in data analysis. The obtained binary rate coefficients for recombination of KrH + and KrD + are α KrH+ = 2x10 -8 cm 3 s -1 and α KrD+ = 1x10 -8 cm 3 s -1 .

  8. Recombination of KrD+ and KrH+ ions in afterglow plasma

    Science.gov (United States)

    Korolov, I.; Kotrik, T.; Plasil, R.; Hejduk, M.; Varju, J.; Dohnal, P.; Glosik, J.

    2009-11-01

    Reported is flowing afterglow (FALP) study of recombination of KrH+ and KrD+ ions with electrons at 250 K in mixtures of He/Kr/H2 and He/Kr/D2, respectively. The influence of fast recombining cluster ions formation on apparent effective recombination rate coefficients (αeff) was measured and used in data analysis. The obtained binary rate coefficients for recombination of KrH+ and KrD+ are αKrH+ = 2×10-8 cm3s-1 and αKrD+ = 1×10-8 cm3s-1.

  9. A universal salt model based on under-ground precipitation of solid salts due to supercritical water `out-salting'

    Science.gov (United States)

    Rueslåtten, H.; Hovland, M. T.

    2010-12-01

    One of the common characteristics of planets Earth and Mars is that both host water (H2O) and large accumulations of salt. Whereas Earth’s surface-environment can be regarded as ‘water-friendly’ and ‘salt hostile’, the reverse can be said for the surface of Mars. This is because liquid water is stable on Earth, and the atmosphere transports humidity around the globe, whereas on planet Mars, liquid water is unstable, rendering the atmosphere dry and, therefore, ‘salt-friendly’. The riddle as to how the salt accumulated in various locations on those two planets, is one of long-lasting and great debate. The salt accumulations on Earth are traditionally termed ‘evaporites’, meaning that they formed as a consequence of the evaporation of large masses of seawater. How the accumulations on Mars formed is much harder to explain, as an ocean only existed briefly. Although water molecules and OH-groups may exist in abundance in bound form (crystal water, adsorbed water, etc.), the only place where free water is expected to be stable on Mars is within underground faults, fractures, and crevices. Here it likely occurs as brine or in the form of ice. Based on these conditions, a key to understanding the accumulation of large deposits of salt on both planets is linked to how brines behave in the subsurface when pressurized and heated beyond their supercritical point. At depths greater than about 3 km (P>300 bars) water will no longer boil in a steam phase. Rather, it becomes supercritical and will attain the phase of supercritical water vapor (SCRIW) with a specific gravity of typically 0.3 g/cm3. An important characteristic of SCRIW is its inability to dissolve the common sea salts. The salt dissolved in the brines will therefore precipitate as solid particles when brines (seawater on the Earth) move into the supercritical P&T-domain (T>400°C, P>300 bars). Numerical modeling of a hydrothermal system in the Atlantis II Deep of the Red Sea indicates that a

  10. Lifetime measurement in {sup 74}Kr and {sup 76}Kr

    Energy Technology Data Exchange (ETDEWEB)

    Goergen, A.; Clement, E.; Chatillon, A.; Korten, W.; Le Coz, Y.; Theisen, Ch. [DAPNIA/SPhN, CEA Saclay, Gif-sur-Yvette Cedex (France); Dewald, A.; Melon, B.; Moeller, O.; Zell, K.O. [Universitaet zu Koeln, Institut fuer Kernphysik, Koeln (Germany); Marginean, N.; Tonev, D. [INFN-Laboratori Nazionali di Legnaro, Legnaro (Padova) (Italy); Menegazzo, R.; Ur, C.A. [Universita di Padova and INFN Sezione di Padova, Dipartimento di Fisica, Padova (Italy)

    2005-11-01

    Lifetimes of excited states in the ground-state bands of {sup 74}Kr and {sup 76}Kr were measured using the recoil-distance Doppler-shift and the differential decay curve methods. The states were populated in the {sup 40}Ca({sup 40}Ca,{alpha}2p) and {sup 40}Ca({sup 40}Ca,4p) reactions. Gamma rays were detected with the GASP array which was coupled to the Cologne Plunger device. The results resolve discrepancies between earlier lifetime measurements and a recent Coulomb excitation experiment. Experimental transition rates are compared to theoretical calculations. The results support a strong mixing between prolate and oblate configurations for the low-spin states, and represent an important basis for the interpretation and understanding of the shape coexistence phenomenon in this mass region. (orig.)

  11. Development and selection of a matrix alloy for 85Kr encapsulation

    International Nuclear Information System (INIS)

    Knoll, R.W.; McClanahan, E.D.; Tingey, G.L.; McDonald, E.L.

    1986-07-01

    Pacific Northwest Laboratory has developed and demonstrated a pilot-scale process for stable, long-term storage of radioactive 85 Kr gas from spent nuclear fuel. The process entraps the Kr into a solid metal matrix that can be safely stored at ambient pressure. For this matrix numerous alloys were first screened; those that best satisfied the selection criteria were Cu-Y, Ni-Y, and Ni-La. Of these, Cu-Y alloys containing approximately 20 at.% Y were recommended for use in the pilot-scale system. Reasons for this decision, based on the development work described in Section 5, are summarized here. Thick Cu-Y-Kr deposits (greater than or equal to1 mm) exhibit much better thermal and mechanical stability than do those of Ni-La-Kr and are at least as stable as Ni-Y-Kr deposits. Cu-Y-Kr coatings are very compatible with the sputtering process. They adhere well to the substrate, do not spall significantly during deposition, and can be deposited at higher rates than the Ni-base alloys. This faster deposition helps compensate, in terms of process efficiency, for the lower Kr capacity of Cu-Y-Kr alloys. Another advantage of Cu-Y over Ni-base alloys is the higher vapor pressure of Cu compared to Ni. This reduces the unwanted buildup of Cu on the hot anode surface, whereas deposition of Ni is a problem with Ni-Y, for example. Cu-Y-Kr deposits containing 17 to 20 at. % Y and 6 to 8 at. % Kr compared favorably to Ni 80 La 10 Kr 10 in terms of long-term Kr retention characteristics. The measurements of Cu-Y-Kr by differential scanning calorimetry also indicated stable retention of Kr because rapid release did not occur below approx.650 0 C. Finally, Cu-Y alloys are satisfactory in terms of materials costs and producibility of the sputtering target. 13 refs., 9 figs., 4 tabs

  12. Precipitation in solid solution and structural transformations in single crystals of high rhenium ruthenium-containing nickel superalloys at high-temperature creep

    Energy Technology Data Exchange (ETDEWEB)

    Alekseev, A.A.; Petrushin, N.V.; Zaitsev, D.V.; Treninkov, I.A.; Filonova, E.V. [All-Russian Scientific Research Institute of Aviation Materials (VIAM), Moscow (Russian Federation)

    2010-07-01

    The phase composition and structure of single crystals of two superalloys (alloy 1 and alloy 2) were investigated in this work. For alloy 1 (Re - 9 wt%) the kinetics of precipitation in solid solution at heat treatment (HT) was investigated. TEM and X-Ray examinations have revealed that during HT rhombic phase (R-phase) precipitation (Immm class (BCR)) occurs. The TTT diagram is plotted, it contains the time-temperature area of the existence of R-phase particles. The element content of R-phase is identified (at. %): Re- 51.5; Co- 23.5; Cr- 14.8; Mo- 4.2; W- 3.3; Ta- 2.7. For alloy 2 (Re - 6.5 wt %, Ru - 4 wt %) structural transformations at high-temperature creep are investigated. By dark-field TEM methods it is established, that in alloy 2 the additional phase with a rhombic lattice is formed during creep. Particles of this phase precipitate in {gamma}-phase and their quantity increases during high-temperature creep. It is revealed that during creep 3-D dislocation network is formed in {gamma}-phase. At the third stage of creep the process of inversion structure formation is observed in the alloy, i.e. {gamma}'-phase becomes a matrix. Thus during modeling creep the volume fraction of {gamma}'-phase in the samples increases from 30% (at creep duration of 200 hrs) up to 55% (at 500 hrs). The processes of structure formation in Re and Ru-containing nickel superalloys are strongly affected by decomposition of solid solution during high-temperature creep that includes precipitation of additional TCP-phases. (orig.)

  13. Evaluation of operational parameters on the precipitation of endoglucanase and xylanase produced by solid state fermentation of Aspergillus niger

    Directory of Open Access Journals (Sweden)

    C. S. Farinas

    2011-03-01

    Full Text Available In order to develop cost effective processes for converting biomass into biofuels, it is essential to improve enzyme production yields, stability and specific activity. In this context, the aim of this work was to evaluate the concentration of two enzymes involved in the hydrolysis of biomass, endoglucanase and xylanase, through precipitation. Statistical experimental design was used to evaluate the influence of precipitant agent concentration (ammonium sulfate and ethanol, aging time, and temperature on enzyme activity recovery. Precipitant agent concentration and aging time showed a statistically significant effect at the 95% confidence level, on both enzyme activity recoveries. The recovery of endoglucanase with ammonium sulfate and ethanol reached values up to 65 and 61%, respectively. For xylanase, the recovery rates were lower, 27 and 25% with ammonium sulfate and ethanol, respectively. The results obtained allowed the selection of the variables relevant to improving enzyme activity recovery within operational conditions suitable for industrial applications.

  14. Geophysical borehole logging of the boreholes KR23 extension, KR29 and KR29b at Olkiluoto 2004

    International Nuclear Information System (INIS)

    Lahti, M.; Heikkinen, E.

    2005-04-01

    Suomen Malmi Oy conducted geophysical borehole logging of the boreholes KR23 extension, KR25b, KR29 and KR29b at the Olkiluoto site in Eurajoki during October 2004. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and processing of the acoustic data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  15. Geophysical borehole logging of the boreholes KR23 extension, KR29 and KR29b at Olkiluoto 2004

    Energy Technology Data Exchange (ETDEWEB)

    Lahti, M. [Suomen Malmi Oy, Espoo (Finland); Heikkinen, E. [JP-Fintact Oy, Vantaa (Finland)

    2005-04-15

    Suomen Malmi Oy conducted geophysical borehole logging of the boreholes KR23 extension, KR25b, KR29 and KR29b at the Olkiluoto site in Eurajoki during October 2004. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and processing of the acoustic data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  16. A feasibility study of the preparation of (U,Gd)3O8 solid solutions by thermal decomposition of co-precipitated carbonate mixtures

    International Nuclear Information System (INIS)

    Ravindran, P.V.; Rajagopalan, K.V.; Mathur, K.P.

    1998-01-01

    Co-precipitation from equimolar nitrate solutions of uranium (VI) and gadolinium has been used to obtain a mixture of (NH 4 ) 4 UO 2 (CO 3 ) 3 and Gd 2 (CO 3 ) 3 .3H 2 O at a pre-determined composition. Simultaneous measurements by TG, DTA and evolved gas analysis (EGA) showed that a calcination temperature of 700 C was necessary to decompose the carbonate completely to oxides. X-ray diffraction data indicated that a solid solution of Gd 2 O 3 in U 3 O 8 cannot be obtained by heating the carbonate mixtures up to 800 C in inert atmospheres. (orig.)

  17. Recombination of KrD{sup +} and KrH{sup +} ions in afterglow plasma

    Energy Technology Data Exchange (ETDEWEB)

    Korolov, I; Kotrik, T; Plasil, R; Hejduk, M; Varju, J; Dohnal, P; Glosik, J, E-mail: juraj.glosik@mff.cuni.c [Department of Surface and Plasma Science, Faculty of Mathematics and Physics, Charles University in Prague (Czech Republic)

    2009-11-15

    Reported is flowing afterglow (FALP) study of recombination of KrH{sup +} and KrD{sup +} ions with electrons at 250 K in mixtures of He/Kr/H{sub 2} and He/Kr/D{sub 2}, respectively. The influence of fast recombining cluster ions formation on apparent effective recombination rate coefficients ({alpha}{sub eff}) was measured and used in data analysis. The obtained binary rate coefficients for recombination of KrH{sup +} and KrD{sup +} are {alpha}{sub KrH+} = 2x10{sup -8} cm{sup 3}s{sup -1} and {alpha}{sub KrD+} = 1x10{sup -8} cm{sup 3}s{sup -1}.

  18. Supported liquid membrane based removal of lead(II) and cadmium(II) from mixed feed: Conversion to solid waste by precipitation.

    Science.gov (United States)

    Bhatluri, Kamal Kumar; Manna, Mriganka Sekhar; Ghoshal, Aloke Kumar; Saha, Prabirkumar

    2015-12-15

    Simultaneous removal of two heavy metals, lead(II) and cadmium(II), from mixed feed using supported liquid membrane (SLM) based technique is investigated in this work. The carrier-solvent combination of "sodium salt of Di-2-ethylhexylphosphoric acid (D2EHPA) (4% w/w) in environmentally benign coconut oil" was immobilized into the pores of solid polymeric polyvinylidene fluoride (PVDF) support. Sodium carbonate (Na2CO3) was used as the stripping agent. Carbonate salts of lead(II) and cadmium(II) were formed in the stripping side interface and they were insoluble in water leading to precipitation inside the stripping solution. The transportation of solute is positively affected due to the precipitation. Lead(II) removal was found to be preferential due to its favorable electronic configuration. The conversion of the liquid waste to the solid one was added advantage for the final removal of hazardous heavy metals. Copyright © 2015 Elsevier B.V. All rights reserved.

  19. Apparent 85Kr ages of groundwater within the Royal watershed, Maine, USA.

    Science.gov (United States)

    Sidle, W C

    2006-01-01

    Specific 85Kr activity is mapped from 264 domestic and municipal wells sampled during 2002-2004 in the Royal watershed (361 km2), Maine. Gas samples are collected at 20 m, 40 m, and > 50 m interval depths within the unconfined aquifers. Gas extraction for 85Kr from wells is obtained directly via a wellhead methodology avoiding conventional collection of large sample volumes. Atmospheric 85Kr input to the recharge environment is estimated at 1.27 Bq m(-3) by time-series analyses of weighted monthly precipitation (2001-2004). Numerical simulation of Kr gas transport through the variable unsaturated zones to the water table suggests up to 12-year time lags locally, thus biasing the 85Kr groundwater ages. Apparent 85Kr ages suggest that approximately 70% of groundwater near 20 m depth was recharged less than 30 years BP (2004). Mass-age transport modeling suggests that post mid-1950s recharge penetrates to part of the basin's floor and that older groundwater seeps from the underlying fractured bedrock may occur.

  20. Geophysical logging and imaging of drillholes OL-KR45, OL-KR49, OL-KR50 and OL-KR50B at Olkiluoto in 2009

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.

    2010-04-01

    Suomen Malmi Oy conducted geophysical drillhole logging, acoustic imaging and optical imaging of the drillholes OL-KR45 (re-measurements), OL-KR49, OL-KR50 and OL-KR50B at the Olkiluoto site in Eurajoki during January-November 2009. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and data processing. The report describes field operation, equipment as well as processing procedures and shows the obtained results and an analysis of their quality in the appendices. The raw and processed data are delivered digitally in WellCAD, PDF and Excel format. The missing density logging of drillhole OL-KR45 was carried out successfully. Dynamic rock mechanical parameters and natural gamma data were re-processed and this report includes updated WellCAD and Excel files. Acoustic imaging was also carried out in OL-KR45 after 700 meters depth. Acoustic imaging was used instead of optical imaging after 350 meters in OL-KR49 and 700 meters in OL-KR50. (orig.)

  1. Ne beam-Kr target interaction

    Energy Technology Data Exchange (ETDEWEB)

    Fortov, V E; Kostin, V V; Vorob` ev, V S [Russian Academy of Sciences, Moscow (Russian Federation). High Energy Density Research Center; Kulish, M I; Mintsev, V B [Russian Academy of Sciences, Chernogolovka (Russian Federation). Inst. of Chemical Physics; Hoffman, [Gesellschaft fuer Schwerionenforschung, Darmstadt (Germany)

    1997-12-31

    Energetic heavy ions of Ne - crystal Kr target interaction is investigated both experimentally and with the help of a 2-D computer code. The dynamics of the target matter heating, expansion, and destruction are described. A new equation of state for Kr was obtained and tested within a wide range of parameters. (author). 2 figs., 10 refs.

  2. Solution and precipitation of excess phases and nitrogen partition between solid solution and nitrides in corrosion-resistant steel

    International Nuclear Information System (INIS)

    Kaputkina, L.M.; Svyazhin, A.G.; Prokoshkina, V.G.

    2006-01-01

    Experimental study results on dissolution and precipitation of nitrides during crystallization and heat treatment of high nitrogen austenitic steels are presented. It is established that even on rapid crystallization most of nitrogen is in nitrides, and for their dissolution high temperatures and long-term holding at heat are needed. A nitrogen content in the steel should be optimized according to the structure required (austenite or austenite + excess phases). It is noted that a high nitrogen concentration in the steel is not necessarily efficient to attain a high strength [ru

  3. Contribution to the study of the physical stability of the suspensions of zinc oxide, titanium dioxide and precipitated sulphur employing emulsified solid greases like vehicle

    International Nuclear Information System (INIS)

    Porras Navarro, Martha

    2001-01-01

    This research evaluated the physical stability of the suspensions of zinc oxide, precipitated sulphur and titanium dioxide. By using emulsified vehicles of three solid greases: stearilic alcohol, stearic acid and beeswax. That varies the concentration of solid grease (2%, 4%, 6 %) and the velocity of agitation for the emulsified vehicle's preparation (250, 500, 750 revolutions by minutes). That got 81 suspensions, 27 for every grease employed. The following effects there were evaluated like indicators of the physical stability of the suspensions: volume of sediment, apparent viscosity, facility of resuspension. There was effected an analysis of the varying of two controlled factors to establish the importance since the statistical viewpoint of the variants of the process over the volume of the sediment. This study indicates that the selection of solid grease is an parameter which influence is significant, what supports the got data through the research. By giving as a result that the stearilic alcohol is the most competent vehicle for the preparation of these suspensions. (Author) [es

  4. Gaseous 83mKr generator for KATRIN

    Science.gov (United States)

    Sentkerestiová, J.; Dragoun, O.; Lebeda, O.; Ryšavý, M.; Sturm, M.; Vénos, D.

    2018-04-01

    Monoenergetic conversion electrons from the 83mKrKr isomeric state have been proven to be useful in the calibration of several tritium neutrino mass and dark matter experiments. In this paper the design and characteristics of the gaseous 83mKrKr generator, including the 83Rb/83mKrKr source behavior in tritium, for the KATRIN experiment are presented. Using Si(Li) and silicon drift detectors (SDD) detectors, the half-life of the 83mKrKr isomeric state was measured to be 1.8620 ± 0.0019 h.

  5. Geophysical borehole logging of the boreholes KR37, KR37B and KR38, at Olkiluoto 2005

    International Nuclear Information System (INIS)

    Majapuro, J.

    2006-03-01

    Suomen Malmi Oy conducted geophysical borehole logging of the boreholes KR37, KR37b and KR38 at the Olkiluoto site in Eurajoki during September and October 2005. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and processing of the acoustic data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  6. Geophysical logging and imaging of characterisation drillholes ONK-KR13, ONK-KR14 and ONK-KR15

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.

    2011-08-01

    Suomen Malmi Oy conducted geophysical drillhole logging as well as optical and acoustic imaging of drillholes ONK-KR13, ONK-KR14 and ONK-KR15 at ONKALO in June-July 2010 and in March 2011. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and data processing. The report describes field operation, equipment as well as processing procedures and shows the obtained results and an analysis of their quality in the appendices. The raw and processed data are delivered digitally in WellCAD, PDF and Excel format. (orig.)

  7. Removal or excitation of a 1s electron in Kr II and Kr III

    International Nuclear Information System (INIS)

    Pan Lin; Beck, Donald R; O'Malley, Steven M

    2005-01-01

    Relativistic configuration interaction calculations are done for Kr ions Kr II and Kr III. Transition energies and transition probabilities for 122 transitions between Kr II 4p 5 J = 1/2, 3/2→ 1s 4p 6 , 1s 4p 5 np (n = 5-8) J = 1/2, 3/2, 5/2; 437 transitions between Kr III 4p 4 J = 0, 1, 2→ 1s 4p 5 , 1s 4p 4 np (n = 5-8) J = 0, 1, 2, 3 have been calculated. These data have been used by experiment to reproduce the absorption spectrum of Kr II and Kr III and found to be in good agreement with their measurement. Also, the K-edge energy of neutral Kr, Kr II and Kr III has been calculated. The first is within 0.94 eV of an existing experiment, while the last two are calculated for the first time

  8. Drillhole gamma-ray spectrum logging in drillholes OL-KR11, OL-KR44, OL-KR44B, OL-KR45B, OL-KR46, OL-KR47, OL-KR47B, OL-KR48 and ground survey at Olkiluoto in Eurajoki, 2007 and 2008

    Energy Technology Data Exchange (ETDEWEB)

    Julkunen, A.; Kallio, L.; Kuusisto, M. (Astrock Oy, Sodankylae (Finland))

    2009-09-15

    The aim of the detailed drillhole surveys is to increase the knowledge of the bedrock on the study area and to supplement the investigations made earlier. As a part of the detailed investigations Astrock Oy carried out drillhole spectrometer logging in drillholes OL-KR11, OL-KR44, OL-KR44B, OL-KR45B, OL-KR46, OL-KR47, OL-KR47B, OL-KR48 and ground survey at Olkiluoto site in Eurajoki during 2007 and 2008. This report describes the logging, data processing and the results. For the first time the results contains moving standard deviation calculations of Th/K ratio, because the variability of Th/K ratio is a reasonably good indicator of alteration zones. This report includes also moving standard deviation calculations of Th/K ratio from earlier measured and reported drillholes OL-KR40-43 and OL-KR40B-43B. (orig.)

  9. The influence of precipitation kinetics on trace element partitioning between solid and liquid solutions: A coupled fluid dynamics/thermodynamics framework to predict distribution coefficients

    Science.gov (United States)

    Kavner, A.

    2017-12-01

    In a multicomponent multiphase geochemical system undergoing a chemical reaction such as precipitation and/or dissolution, the partitioning of species between phases is determined by a combination of thermodynamic properties and transport processes. The interpretation of the observed distribution of trace elements requires models integrating coupled chemistry and mechanical transport. Here, a framework is presented that predicts the kinetic effects on the distribution of species between two reacting phases. Based on a perturbation theory combining Navier-Stokes fluid flow and chemical reactivity, the framework predicts rate-dependent partition coefficients in a variety of different systems. We present the theoretical framework, with applications to two systems: 1. species- and isotope-dependent Soret diffusion of species in a multicomponent silicate melt subjected to a temperature gradient, and 2. Elemental partitioning and isotope fractionation during precipitation of a multicomponent solid from a multicomponent liquid phase. Predictions will be compared with results from experimental studies. The approach has applications for understanding chemical exchange in at boundary layers such as the Earth's surface magmatic systems and at the core/mantle boundary.

  10. In Situ Lipolysis and Synchrotron Small-Angle X-ray Scattering for the Direct Determination of the Precipitation and Solid-State Form of a Poorly Water-Soluble Drug During Digestion of a Lipid-Based Formulation

    DEFF Research Database (Denmark)

    Khan, Jamal; Hawley, Adrian; Rades, Thomas

    2016-01-01

    In situ lipolysis and synchrotron small-angle X-ray scattering (SAXS) were used to directly detect and elucidate the solid-state form of precipitated fenofibrate from the digestion of a model lipid-based formulation (LBF). This method was developed in light of recent findings that indicate variab...... on drugs, and experimental conditions, which are anticipated to produce altered solid-state forms upon the precipitation of drug (i.e., polymorphs, amorphous forms, and salts). © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association J Pharm Sci....

  11. Long term storage techniques for 85Kr

    International Nuclear Information System (INIS)

    Foster, B.A.; Pence, D.T.; Staples, B.A.

    1975-01-01

    As new nuclear fuel reprocessing plants go on stream, the collection of fission product 85 Kr will be required to avoid potential local release problems and long-term atmospheric buildup. Storage of the collected 85 Kr for a period of at least 100 years will be necessary to allow approximately 99.9 percent decay before it is released. A program designed to develop and evaluate proposed methods for long-term storage of 85 Kr is discussed, and the results of a preliminary evaluation of three methods, high pressure steel cylinders, zeolite encapsulation, and clathrate inclusion are presented. (U.S.)

  12. A Mossbauer study of Kr incorporations in sputtered a-Si films

    NARCIS (Netherlands)

    Rosu, M.F; Niesen, L; van Veen, A.; Sloof, W.G.

    1996-01-01

    Krypton atoms incorporated in sputtered a-silicon films are investigated by means of Kr-83 Mosssbauer spectroscopy. The hyperfine parameters of the (RbI)-Rb-83 source were determined by taking a spectrum against solid krypton. Mossbauer spectra were taken for films containing krypton concentrations

  13. Effect of solid fission products forming dissolved oxide(Nd) and metallic precipitate(Ru) on the thermophysical properties of MOX fuel

    International Nuclear Information System (INIS)

    Kim, Dong Joo

    2006-02-01

    This study experimentally investigated the effect of solid fission products on the thermophysical properties of the mixed oxide fuel and evaluated them on the basis of the analytical theory. Neodymium and ruthenium were selected for the experiments to represent the physical states of the solid fission product as a 'dissolved oxide' and 'metallic precipitate', respectively. The state of the additives, crystal structures, lattice parameters, and theoretical densities were investigated with X-ray diffraction (XRD). Thermal diffusivities and thermal expansion rates were measured with laser flash method and dilatometry, respectively. The thermal expansion data were then fitted to obtain an correlation equation of the density variation as a function of the temperature. The specific heat capacity values were determined using the Neumann-Kopp's rule. The thermal expansion of the 'Nd.added' sample linearly increased with the concentration of the neodymium, which is primarily due to the fact that the melting point of Nd 2 O 3 is lower than that of UO 2 . On the other hand, the thermal expansion of the 'Ru.added' sample hardly changed with increasing ruthenium content. Thermal conductivities of the simulated MOX fuel were determined on the basis of the thermal diffusivities, density variation, and specific heat values measured in this study. The effect of additives on the thermal conductivity of the samples was quantified in the form of the thermal resistance equation, the reciprocal of the phonon conduction equation, which was determined from measured data. For 'dissolved oxide' sample in the UO 2 matrix, the effect is mainly attributed to the increase of lattice point defects caused by U 4+ , Ce 4+ , Nd 3+ and O 2- ions, which play the role of phonon scattering centers, that is, mean free path of phonon scattering decreases with the point defects, thus increase the thermal resistance. Also, the mass difference between the host (U) and the substituted atom (Ce and/or Nd) can

  14. The excited states of 79Kr

    International Nuclear Information System (INIS)

    Liptak, J.; Kristiak, J.; Kristiakova, K.

    1977-01-01

    The β + -decay of 79 Rb has been studied with Ge(Li) detectors in single and coincidence modes. The half-life of the 147.06 keV level in 79 Kr has been determined to be (78+-6) ns. The relative electron intensities of seventeen transitions have been measured with a magnetic Si(Li) spectrometer. The internal conversion coefficients have been determined. The transition multipolarities have been deduced. The spin-parity assignments have been made for excited states of 79 Kr and a β-decaying sta 79 Rb(5/2 + ). The structure of excited states in 79 Kr is discussed in the framework of the Alaga and Coriolis coupling models. It is shown that the properties of some levels in 79 Kr can be explained by the existence of relatively pure rotational bands

  15. The Electra KrF Laser Program

    National Research Council Canada - National Science Library

    Sethian, J. D; Hegeler, F; Myers, M; Friedman, M; Obenschain, S; Lehmberg, R; Giuliani, J; Kepple, P; Swanekamp, S; Smith, I

    2002-01-01

    Electra is a repetitively pulsed, electron-beam pumped, Krypton Fluoride "KrF" laser that will develop the technologies that can meet the Inertial Fusion Energy "IFE" requirements for durability, efficiency, and cost...

  16. Mise-a-la-masse measurements in drillholes OL-KR4, OL-KR30 and OL-KR14 - OL-KR18 in Olkiluoto

    International Nuclear Information System (INIS)

    Kristiansson, S.; Heikkinen, P.

    2009-02-01

    Mise-a-la-masse measurements were conducted in the Olkiluoto investigation site in the time period from May to November 2007. Measurements were carried out in drillholes OL-KR4, OL-KR30 and OL-KR14 - OL-KR18. The purpose of the study was to collect data for geological modelling. The aim is to evaluate the continuity of fractures and other geological structures from a drillhole to another drillhole and from a drillhole to the ground surface. Posiva has developed electrodes for mise-a-la-masse method measurements, where the location of the electrode is between rubber disks similar to the flow guide. Rubber disks prevent leakage of current along the drillhole and focus current directly to a specific fracture. (orig.)

  17. Symmetric resonance double charge transfer in Kr++ + Kr and Xe++ + Xe systems

    International Nuclear Information System (INIS)

    Okuno, K.; Koizumi, T.; Kaneko, Y.

    1978-01-01

    Cross sections of processes Kr ++ + Kr → Ke + Kr ++ and Xe ++ + Xe → Xe + Xe ++ were measured by the injected-ion-drift-tube technique from 0.04 to 20 eV. For both cases, the cross section below 1 eV coincides with the orbiting cross sections with a charge-transfer probability 1/2. Above 1 eV, the energy dependence of the cross sectcion is like that for single charge transfer. Mobilities of Kr ++ and Xe ++ in He are presented also

  18. Neutron capture cross sections of Kr

    Directory of Open Access Journals (Sweden)

    Fiebiger Stefan

    2017-01-01

    Full Text Available Neutron capture and β− -decay are competing branches of the s-process nucleosynthesis path at 85Kr [1], which makes it an important branching point. The knowledge of its neutron capture cross section is therefore essential to constrain stellar models of nucleosynthesis. Despite its importance for different fields, no direct measurement of the cross section of 85Kr in the keV-regime has been performed. The currently reported uncertainties are still in the order of 50% [2, 3]. Neutron capture cross section measurements on a 4% enriched 85Kr gas enclosed in a stainless steel cylinder were performed at Los Alamos National Laboratory (LANL using the Detector for Advanced Neutron Capture Experiments (DANCE. 85Kr is radioactive isotope with a half life of 10.8 years. As this was a low-enrichment sample, the main contaminants, the stable krypton isotopes 83Kr and 86Kr, were also investigated. The material was highly enriched and contained in pressurized stainless steel spheres.

  19. Energy levels and radiative rates for transitions in B-like to F-like Kr ions (Kr XXXII XXVIII)

    Science.gov (United States)

    Aggarwal, K. M.; Keenan, F. P.; Lawson, K. D.

    2008-05-01

    Energy levels, radiative rates, oscillator strengths, line strengths, and lifetimes have been calculated for transitions in B-like to F-like Kr ions, Kr XXXIII-XXVIII. For the calculations, the fully relativistic GRASP code has been adopted, and results are reported for all electric dipole (E1), electric quadrupole (E2), magnetic dipole (M1), and magnetic quadrupole (M2) transitions among the lowest 125, 236, 272, 226, and 113 levels of Kr XXXII, Kr XXXI, Kr XXX, Kr XXIX, and Kr XXVIII, respectively, belonging to the n ⩽ 3 configurations. Comparisons are made with earlier available theoretical and experimental results, and some discrepancies have been noted and explained.

  20. Structure of high spin states of 76Kr and 78Kr nuclei

    Indian Academy of Sciences (India)

    Evolution of the shape with spin, and rotation alignment of proton as well as neutron ... by studying ground state properties of 76,78Kr by employing two sets of basis .... Figure 3. Energies of the yrast states of 76,78Kr nuclei compared with the.

  1. K-edge x-ray-absorption spectroscopy of laser-generated Kr+ and Kr2+

    International Nuclear Information System (INIS)

    Southworth, S. H.; Arms, D. A.; Dufresne, E. M.; Dunford, R. W.; Ederer, D. L.; Hoehr, C.; Kanter, E. P.; Kraessig, B.; Landahl, E. C.; Peterson, E. R.; Rudati, J.; Santra, R.; Walko, D. A.; Young, L.

    2007-01-01

    Tunable, polarized, microfocused x-ray pulses were used to record x-ray absorption spectra across the K edges of Kr + and Kr 2+ produced by laser ionization of Kr. Prominent 1s→4p and 5p excitations are observed below the 1s ionization thresholds in accord with calculated transition energies and probabilities. Due to alignment of 4p hole states in the laser-ionization process, the Kr + 1s→4p cross section varies with respect to the angle between the laser and x-ray polarization vectors. This effect is used to determine the Kr + 4p 3/2 and 4p 1/2 quantum state populations, and these are compared with results of an adiabatic strong-field ionization theory that includes spin-orbit coupling

  2. Optical imaging of drillholes OL-KR40, OL-KR41, OL-KR41B, OL-KR42, OL-KR42B, OL-KR43 and OL-KR43B at Olkiluoto, 2006 and 2007

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.

    2007-03-01

    Suomen Malmi Oy carried out optical imaging of drillholes OL-KR40, OL-KR41, OL-KR41B, OL-KR42, OL-KR42B, OL-KR43 and OL-KR43B at Olkiluoto site in Eurajoki during July, August, November and December 2006 as well as January 2007. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and the data processing. This report describes the field operation, the equipment as well as the processing procedures and shows the obtained results and their quality. The raw and processed data are delivered digitally in WellCAD and PDF format. (orig.)

  3. Geophysical borehole logging and optical imaging of the boreholes KR34, KR35 and KR36, at Olkiluoto 2005

    Energy Technology Data Exchange (ETDEWEB)

    Majapuro, J. [Suomen Malmi Oy, Espoo (Finland)

    2005-09-15

    Suomen Malmi Oy conducted geophysical borehole logging and optical imaging surveys of the boreholes KR34, KR35 and KR36 at the Olkiluoto site in Eurajoki during May - June 2005. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The methods applied are magnetic susceptibility, natural gamma radiation, gamma-gamma density, single point resistance, Wenner-resistivity, borehole radar, full waveform sonic and optical imaging. The assignment included the field work of all surveys, interpretation and processing of the acoustic and borehole radar data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  4. Geophysical borehole logging and optical imaging of the boreholes KR34, KR35 and KR36, at Olkiluoto 2005

    International Nuclear Information System (INIS)

    Majapuro, J.

    2005-09-01

    Suomen Malmi Oy conducted geophysical borehole logging and optical imaging surveys of the boreholes KR34, KR35 and KR36 at the Olkiluoto site in Eurajoki during May - June 2005. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The methods applied are magnetic susceptibility, natural gamma radiation, gamma-gamma density, single point resistance, Wenner-resistivity, borehole radar, full waveform sonic and optical imaging. The assignment included the field work of all surveys, interpretation and processing of the acoustic and borehole radar data. The report describes the field operation, equipment as well as processing procedures and shows the obtained results and their quality in the appendices. The raw and processed data are delivered digitally in WellCAD and Excel format. (orig.)

  5. Release of dissolved 85Kr by standing

    International Nuclear Information System (INIS)

    Ootsuka, Norikatsu; Yamamoto, Tadatoshi; Tsukui, Kohei

    1986-01-01

    The experiments on the release of dissolved 85 Kr by standing at room temperature were carried out to examine the influence of liquid level in a sampler and properties of solvent on the release efficiency. Six kinds of organic solvents as well as water were taken as solvents. The half-life period in case of the decrease in concentration of the dissolved 85 Kr which was used as an index of release efficiency, was proportional to the liquid level in the sampler and was inversely proportional to the diffusion coefficient of Kr gas in solvent. For organic solvents belonging to homologous series, the half-life period became longer with increasing the carbon number of solvent molecule. From the relationship between the half-life period and the carbon number, the release efficiency in the dissolved 85 Kr can be predicted for any commonly used solvent as a practical application. This method was found to be an effective means of removing the dissolved 85 Kr of low level though it takes rather long time. (author)

  6. Asymmetrical Precipitation of Ag3Sn Intermetallic Compounds Induced by Thermomigration of Ag in Pb-Free Microbumps During Solid-State Aging

    Science.gov (United States)

    Su, Yu-Ping; Wu, Chun-Sen; Ouyang, Fan-Yi

    2016-01-01

    Three-dimensional integrated circuit technology has become a major trend in electronics packaging in the microelectronics industry. To effectively remove heat from stacked integrated circuitry, a temperature gradient must be established across the chips. Furthermore, because of the trend toward higher device current density, Joule heating is more serious and temperature gradients across soldered joints are expected to increase. In this study we used heat-sink and heat-source devices to establish a temperature gradient across SnAg microbumps to investigate the thermomigration behavior of Ag in SnAg solder. Compared with isothermal conditions, small Ag3Sn particles near the hot end were dissolved and redistributed toward the cold end under a temperature gradient. The results indicated that temperature gradient-induced movement of Ag atoms occurred from the hot side toward the cold side, and asymmetrical precipitation of Ag3Sn resulted. The mechanism of growth of the intermetallic compound (IMC) Ag3Sn, caused by thermomigration of Ag, is discussed. The rate of growth Ag3Sn IMC at the cold side was found to increase linearly with solid-aging time under a temperature gradient. To understand the force driving Ag diffusion under the temperature gradient, the molar heat of transport ( Q*) of Ag in Sn was calculated as +13.34 kJ/mole.

  7. Geophysical drillhole logging and imaging of drillholes OL-KR51, OL-KR52, OL-KR52B, OL-KR53 and OL-KR53B at Olkiluoto in 2009 and 2010

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.

    2010-10-01

    Suomen Malmi Oy conducted geophysical drillhole logging and optical imaging of the drillholes OL-KR51, OL-KR52, OL-KR52B, OL-KR53 and OL-KR53B at the Olkiluoto site in Eurajoki between November 2009 and February 2010. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and data processing. The report describes field operation, equipment as well as processing procedures and shows the obtained results and an analysis of their quality in the appendices. The raw and processed data are delivered digitally in WellCAD, PDF and Excel format. (orig.)

  8. Hyperfine spectra of the radioactive isotopes 81Kr and 85Kr

    International Nuclear Information System (INIS)

    Cannon, B.D.

    1993-01-01

    Isotope shifts and hyperfine constants are reported for the radioactive isotopes 81 Kr and 85 Kr and the stable isotope 83 Kr. The previously unreported nuclear moments of 81 Kr were determined to be μ I =-0.909(4) nuclear magneton and Q=+0.630(13) b from the hyperfine constants. This work increases the number of transitions for which 85 Kr hyperfine constants and isotope shifts have been measured from 1 to 4. The hyperfine anomaly for krypton reported in the previous measurement of 85 Kr hyperfine constants [H. Gerhardt et al., Hyperfine Interact. 9, 175 (1981)] is not supported by this work. The isotope shifts and hyperfine constants of 83 Kr measured in this work are in excellent agreement with previous work. Saturation spectroscopy was used to study transitions from krypton's metastable 1s 5 state to the 2p 9 , 2p 7 , and 2p 6 states. In saturation spectra, different line shapes were observed for the even- and odd-mass krypton isotopes. This even- versus odd-line-mass shape difference can be explained using the large cross section that has been reported for collisional transfer of the 1s 5 state excitation between krypton atoms. Two-color two-photon laser-induced fluorescence was used to measure the hyperfine spectra of the 1s 5- 4d 4 ' transition using the 2p 9 state as the intermediate state. This technique proved to be more sensitive than saturation spectroscopy

  9. Helbredsrelateret livskvalitet ved kræft

    DEFF Research Database (Denmark)

    Grønvold, Mogens

    2008-01-01

    I denne artikel gennemgås metoder, erfaringer og resultater fra livskvalitetsforskningen på kræftområdet, og der opstilles anbefalinger. Forskningen har omfattet deskriptive undersøgelser, endemål i kliniske undersøgelser, prognostiske studier og klinisk anvendelse af livskvalitetsskemaer. Der vu...... vurderes at være behov for yderligere livskvalitetsundersøgelser ved alle kræftformer og -behandlinger, men de bør kun foretages, når de tilstrækkelige resurser er til stede, da kun velgennemførte studier er af værdi. Udgivelsesdato: 2008-Mar-3...

  10. Tiden kræver nye karakteregenskaber

    DEFF Research Database (Denmark)

    Holm, Claus

    2013-01-01

    I Danmark har vi tradition for, at unges studievalg er styret af faglig interesse og lyst. Men en ny global konkurrencetilstand kræver, at lysten også omfatter vilje til at udføre kedsommelige pligter som moderne og fleksible medarbejdere......I Danmark har vi tradition for, at unges studievalg er styret af faglig interesse og lyst. Men en ny global konkurrencetilstand kræver, at lysten også omfatter vilje til at udføre kedsommelige pligter som moderne og fleksible medarbejdere...

  11. Radioactivity 85Kr in krypton enriched with light isotope

    International Nuclear Information System (INIS)

    Kuz'minov, V.V.; Novikov, V.M.; Pomanskij, A.A.

    1992-01-01

    85 Kr content in krypton enriched with 78 Kr is measured within the frames of experiment for search of binary position decay and conversion of atomic electron into 78 Kr. Voluminous activity in krypton enriched up to 98% 78 Kr equal to 0.206 -0.004 +0.001 Bq/L is obtained which is by 4000 less as compared to natural krypton. 7 refs.; 1 fig.; 1 tab

  12. Los Alamos KrF laser program

    International Nuclear Information System (INIS)

    Jensen, R.J.; Cartwright, D.C.

    1985-01-01

    Los Alamos is currently developing the krypton fluoride (KrF) laser - a highly efficient laser able to emit very intense bursts of short-wavelength photons - as a research tool for the general study of high-density matter, as well as for use in laser fusion. The KrF laser operates at 1/4 μm, close to the short-wavelength limit for conventional optical material, but still in the region where standard optical techniques can be used. The excited-state lifetime of the KrF lasing medium is short - as a result of both spontaneous emission and deactivation from collisions - making it impossible to store energy within the lasing medium for times significant to electrical pumping. However, an optical multiplexing scheme is being developed that will generate short, intense pulses of 1/4-μm light by overcoming the short storage time of the laser and taking advantage of the high gain of the KrF medium

  13. Effect of chronic 85Kr exposure

    International Nuclear Information System (INIS)

    Willard, D.H.; Deford, H.S.; Gerk, R.E.; Ballou, J.E.

    1979-01-01

    Rats are being exposed continuously for their life span to three concentrations of 85 Kr: 3 x 10 -3 , 3 x 10 -4 , and 3 x 10 -5 μCi/ml. A group of treated controls exposed to room air completes the study. No effects of treatment have been observed up to 70 days postexposure

  14. Effect of chronic 85Kr exposure

    International Nuclear Information System (INIS)

    Willard, D.H.; DeFord, H.S.; Ballou, J.E.

    1980-01-01

    Groups of rats exposed continuously for 15 mo to 85 Kr atmospheres have received measured dose rates of 2750, 370, and 38 rad/yr. With more than 75% of the rats still alive, there has been no dose-related effect on weight gain but a probably significant effect on survival

  15. A 223-nm KrCl excimer laser on a He-Kr-HCl mixture

    International Nuclear Information System (INIS)

    Razhev, A M; Zhupikov, A A; Kargapol'tsev, E S

    2004-01-01

    The results of experimental studies of the parameters of a 223-nm electric-discharge KrCl excimer laser on a He-Kr-HCl mixture depending on the excitation conditions and the composition of the active gaseous medium are presented. To achieve the maximum values of the output energy and the efficiency of the KrCl laser on mixtures with buffer gaseous helium, an excitation system was used that included a circuit with an LC inverter with a high-voltage switch based on an RU-65 spark gap. An output energy of 320 mJ with an efficiency of 0.5% relative to the energy stored in the capacitors is obtained in a KrCl laser with an active medium based on the buffer He gas at a charging voltage of 30 kV. Radiation pulses with a duration of 22±1 ns and a pulse power of 15 MW are obtained. (lasers)

  16. Kr atoms and their clustering in zeolite A

    CERN Document Server

    Lim, W T; Jung, K J; Heo, N H

    2001-01-01

    The positions of Kr atoms encapsulated in the molecular-dimensioned cavities of fully dehydrated zeolite A of unit-cell composition Cs sub 3 Na sub 8 HSi sub 1 sub 2 Al sub 1 sub 2 O sub 4 sub 8 (Cs sub 3 -A) have been determined. Cs sub 3 -A was exposed to 1025 atm of krypton gas at 400 .deg. C for four days, followed by cooling at pressure to encapsulate Kr atoms. The resulting crystal structure of Cs sub 3 -A(6Kr) (a=12.247(2) A, R sub 1 =0.078, and R sub 2 =0.085) has been determined by single-crystal X-ray diffraction techniques in the cubic space group Pm3m at 21(1) .deg. C and 1 atm. In the crystal structure of Cs sub 3 -A(6Kr), six Kr atoms per unit cell are distributed over three crystallographically distinct positions: each unit cell contains one Kr atom at Kr(1) on a threefold axis in the sodalite unit, three at Kr(2) opposite four-rings in the large cavity , and two at Kr(3) on threefold axes in the large cavity . Relatively strong interactions of Kr atoms at Kr(1) and Kr(3) with Na sup + ions of ...

  17. Mercury: The Los Alamos ICF KrF laser system

    International Nuclear Information System (INIS)

    Czuchlewski, S.J.; York, G.W.; Bigio, I.J.; Brucker, J.; Hanson, D.; Honig, E.M.; Kurnit, N.; Leland, W.; McCown, A.W.; McLeod, J.; Rose, E.; Thomas, S.; Thompson, D.

    1993-01-01

    The Mercury KrF laser facility at Los Alamos is being built with the benefit of lessons learned from the Aurora system. An increased understanding of KrF laser engineering, and the designed implementation of system flexibility, will permit Mercury to serve as a tested for a variety of advanced KrF technology concepts

  18. Results of sampling and analysis of groundwater from multi-packered boreholes OL-KR1, OL-KR3, OL-KR5, OL-KR9, OL-KR11 and OL-KR12 at Olkiluoto, Eurajoki, in 2004

    Energy Technology Data Exchange (ETDEWEB)

    Hirvonen, H. [Teollisuuden Voima Oyj, Eurajoki (Finland); Hatanpaeae, E. [lnsinoeoeritoimisto Paavo Ristola Oy, Hollola (Finland)

    2005-12-15

    Nine groundwater samples were collected at Olkiluoto from deep multi-packered boreholes OL-KR1, OL-KR3, OL-KR5, OL-KR9, OL-KR11 and OL-KR12 between spring 2004 and the beginning of 2005. The aim of the ground water sampling was to get information for the basis of the monitoring program (OMO) during ONKALO construction. Sampling sections were mainly chosen so that the results of the chemical analyses from earlier studies could be used for comparison. This study presents the sampling methods and the results of the laboratory analyses of groundwater samples from the deep multi-packered boreholes OL-KR1 (151.2-156.8 m, 311.2-336.8 m and 524.4-528.4 m), OL-KR3 (242.6-253.2 m), OL-KR5 (277.2-284.6 m and 457.2-476.2 m), OL-KR9 (468.2-482.2 m), OL-KR11 (597.5-628.1 m) and OLKR12 (363-368 m). The analytical results of the groundwater samplings are compared to earlier analytical results. According to Davis and De Wiest's (1967) classification, the collected groundwater samples represent either the borehole water type Na-Cl (OL-KR1/T/151.2-156.8 m, OLK-R1/ T/311.2-336.8 m, OL-KR3/T/242.6-253.2 m, OL-KR5/T/277.2-284.6 m, OL-KR11/ T/597.5-628.1 m and OL-KR12/T/363-368 m) or Na-Ca-Cl (OL-KR1/T/524.4- 528.4 m, OL-KR5/T/457.2-476.2 m and OL-KR9/T/468.2-482.2 m). The groundwater samples from OL-KR1/T/151.2-156.8 m, OL-KR3/T/242.6- 253.2 m, OL-KR3/T/242.6-253.2 m, OL-KR5/T/277.2-284.2 m, OL-KR11/T/597.5-628.1 m and OL-KR12/T/363-368 m were brackish (1000 mg/L < TDS < 10000 mg/L) according to Davis's (1964) TDS classification. Other samples (OL-KR1/T/524.4-528.4 m, OL-KR5/ T/457.2-476.2 m and OL-KR9/T/468.2-482.2 m), were saline (TDS> 10000 mg/L). Comparison of analytical results of the samples to earlier results shows that some changes were seen between samplings done at the different times. Only the groundwater sampled from OL-KR1/T/311.2-336.8 m had significant changes in its chemical composition during the reference period, but also in OL-KR1/T/524.4-528.4 m, OL-KR5/ T

  19. Observation of asymmetric Stark profiles from plasmas created by a picosecond KrF laser

    International Nuclear Information System (INIS)

    Nam, C.H.; Tighe, W.; Suckewer, S.; Seely, J.F.; Feldman, U.; Woltz, L.A.

    1987-10-01

    High-resolution extreme ultraviolet (XUV) spectra from solid targets irradiated by a picosecond KrF* laser focused to 10 16 W/cm 2 have been recorded. The line profiles of transitions in Li-like fluorine and oxygen are asymmetric and up to 2 A in width. Calculations indicate the presence of transitions of the type 2p-3p and other forbidden Stark components. 11 refs., 6 figs

  20. Kr photoionized plasma induced by intense extreme ultraviolet pulses

    Science.gov (United States)

    Bartnik, A.; Wachulak, P.; Fiedorowicz, H.; Skrzeczanowski, W.

    2016-04-01

    Irradiation of any gas with an intense EUV (extreme ultraviolet) radiation beam can result in creation of photoionized plasmas. The parameters of such plasmas can be significantly different when compared with those of the laser produced plasmas (LPP) or discharge plasmas. In this work, the photoionized plasmas were created in a krypton gas irradiated using an LPP EUV source operating at a 10 Hz repetition rate. The Kr gas was injected into the vacuum chamber synchronously with the EUV radiation pulses. The EUV beam was focused onto a Kr gas stream using an axisymmetrical ellipsoidal collector. The resulting low temperature Kr plasmas emitted electromagnetic radiation in the wide spectral range. The emission spectra were measured either in the EUV or an optical range. The EUV spectrum was dominated by emission lines originating from Kr III and Kr IV ions, and the UV/VIS spectra were composed from Kr II and Kr I lines. The spectral lines recorded in EUV, UV, and VIS ranges were used for the construction of Boltzmann plots to be used for the estimation of the electron temperature. It was shown that for the lowest Kr III and Kr IV levels, the local thermodynamic equilibrium (LTE) conditions were not fulfilled. The electron temperature was thus estimated based on Kr II and Kr I species where the partial LTE conditions could be expected.

  1. Direct Observation of Xe and Kr Adsorption in a Xe-Selective Microporous Metal-Organic Framework

    NARCIS (Netherlands)

    Chen, X.; Plonka, A.M.; Banerjee, D.; Krishna, R.; Schaef, H.T.; Ghose, S.; Thallapally, P.K.; Parise, J.B.

    2015-01-01

    The cryogenic separation of noble gases is energy-intensive and expensive, especially when low concentrations are involved. Metal organic frameworks (MOFs) containing polarizing groups within their pore spaces are predicted to be efficient Xe/Kr solid,state adsorbents, but no experimental insights

  2. Core drilling of drillholes ONK-KR13, ONK-KR14 and ONK-KR15 in ONKALO at Olkiluoto 2010 - 2011

    International Nuclear Information System (INIS)

    Toropainen, V.

    2011-08-01

    As a part of the confirming site investigations at Olkiluoto, Suomen Malmi Oy (Smoy) core drilled three drillholes ONK-KR13 (120.45 m), ONK-KR14 (75.27 m) and ONK-KR15 (79.96 m) in ONKALO, at Olkiluoto in June 2010 - March 2011. The diameter of the drillholes is 75.7 mm. Sodium fluorescein was used as a label agent in the drilling water, and the drillholes were washed and flushed after the drilling. The deviations of the drillholes were measured with the deviation measuring instruments EMS and Gyro. The core samples were logged according to Posiva's normal procedure for drillholes. The main rock types are veined and diatexitic gneisses and pegmatitic granite. The average natural fracture frequencies and RQDs of the core samples are 1.6 pcs/m and 97.0 % (ONK-KR13), 0.5 pcs/m and 99.3 % (ONK-KR14) and 1.6 pcs/m and 97.3 % (ONK-KR15). In drillhole ONK-KR13 one, and in drillhole ONK-KR15 three fractured zones were intersected. There was no fractured zones in drillhole ONK-KR14. Rock mechanical tests were performed to core samples. The average uniaxial compressive strength was 143.2 MPa, the average Young's Modulus was 57.3 GPa and the average Poisson's ratio was 0.25. (orig.)

  3. An improved method for 85Kr analysis by liquid scintillation counting and its application to atmospheric 85Kr determination

    International Nuclear Information System (INIS)

    Momoshima, Noriyuki; Inoue, Fumio; Sugihara, Shinji; Shimada, Jun; Taniguchi, Makoto

    2010-01-01

    Atmospheric 85 Kr concentration at Fukuoka, Japan was determined by an improved 85 Kr analytical method using liquid scintillation counting (LSC). An average value of 1.54 ± 0.05 Bq m -3 was observed in 2008, which is about two times that measured in 1981 at Fukuoka, indicating a 29 mBq y -1 rate of increase as an average for these 27 years. The analytical method developed involves collecting Kr from air using activated charcoal at liquid N 2 temperature and purifying it using He at dry ice temperature, followed by Kr separation by gas chromatography. An overall Kr recovery of 76.4 ± 8.1% was achieved when Kr was analyzed in 500-1000 l of air. The Kr isolated by gas chromatography was collected on silica gel in a quartz glass vial cooled to liquid N 2 temperature and the activity of 85 Kr was measured with a low-background LS counter. The detection limit of 85 Kr activity by the present analytical method is 0.0015 Bq at a 95% confidence level, including all propagation errors, which is equivalent with 85 Kr in 1.3 l of the present air under the analytical conditions of 72.1% counting efficiency, 0.1597 cps background count rate, and 76.4% Kr recovery.

  4. KrF laser kinetics studies

    International Nuclear Information System (INIS)

    Mandl, A.; Klimek, D.; Parks, J.H.

    1984-01-01

    A series of measurements characterizing an e beam pumped KrF* laser was carried out using a 200-nsec e-beam pulse having a rise time of 25 nsec at current densities up to 50 A/cm 2 . These pump conditions are relevent for inertial confinement fusion laser drivers. The measurements include fluorescence efficiency, sidelight suppression of the fluorescence during lasing, and laser energy output over a wide range of laser parameters including: total density 0.5--2.0 amagats, temperature 300--400 K, fluorine density 0.15%--0.5%, current density 38--50 A/cm 2 and various mirror transmissions. This data was used to verify and refine a model of KrF* kinetics which was then used to estimate the performance of an angular multiplexed power amplifier suitable for laser fusion applications

  5. Excitation rates for transitions in Kr XXXII

    Science.gov (United States)

    Aggarwal, K. M.; Keenan, F. P.; Lawson, K. D.

    2009-04-01

    In this paper we report our results for collision strengths and effective collision strengths for transitions among the lowest 125 levels of the 2s22p, 2s2p2, 2p3, 2s23ell, 2s2p3ell, and 2p23ell configurations of Kr XXXII. For our calculations both the FAC and DARC codes have been employed.

  6. Geophysical drillhole logging of the drillholes OL-KR40, OL-KR41, OL-KR41B, OL-KR42, OLKR42B, OL-KR43 and OL-KR43B, at Olkiluoto 2006 and 2007

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.

    2007-05-01

    Suomen Malmi Oy conducted geophysical borehole logging of the boreholes drillholes OL-KR40, OL-KR41, OL-KR41B, OL-KR42, OL-KR42B, OL-KR43 and OL-KR43B at the Olkiluoto site in Eurajoki during August, September, December 2006 and January 2007. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and processing of the acoustic data. The report describes field operation, equipment as well as processing procedures and shows the obtained results and an analysis of their quality in the appendices. The raw and processed data are delivered digitally in WellCAD, PDF and Excel format. (orig.)

  7. High energy KrCl electric discharge laser

    Science.gov (United States)

    Sze, Robert C.; Scott, Peter B.

    1981-01-01

    A high energy KrCl laser for producing coherent radiation at 222 nm. Output energies on the order of 100 mJ per pulse are produced utilizing a discharge excitation source to minimize formation of molecular ions, thereby minimizing absorption of laser radiation by the active medium. Additionally, HCl is used as a halogen donor which undergoes a harpooning reaction with metastable Kr.sub.M * to form KrCl.

  8. ETUDE STRUCTURELLE ET SPECTRES D’ABSORPTION DE Kr3+

    Directory of Open Access Journals (Sweden)

    A CHIKHAOUI

    2001-12-01

    Full Text Available Le présent travail, qui comporte deux étapes, est une étude théorique de l'agrégat de Krypton chargé une fois (Kr3+. La première étape est l'étude structurelle de Kr3+. L'hamiltonien modèle est développé dans le cadre de la méthode D.I.M (Diatomics In Molecules. Les résultats obtenus montrent que Kr3+ est linéaire. La profondeur du puits attractif De est égale  à 0.29 eV par rapport à la dissociation en Kr2+ + Kr pour une distance d'équilibre Re = 5.496 u.a. Ce résultat est en bon accord avec la valeur expérimentale qui vaut 0.27 eV. La deuxième étape est l'étude thermodynamique et spectroscopique de Kr3+. Les résultats obtenus montrent que le spectre vertical de Kr3+ linéaire comporte trois pics situés dans le domaine du visible à 625nm, 551nm et 466nm. L'analyse statistique des populations de charges atomiques montre que Kr3+ subit une isomérisation qui le ramène à une configuration de type ( Kr2+ ...Kr ou à une configuration plus probable de type  (Kr+...Kr2 .

  9. The saturation phenomenon in Kr85 ion implantation in metallic targets

    International Nuclear Information System (INIS)

    Baptista Junior, V. de P.

    1978-01-01

    Noble gases, as Krypton containing the radioative isotope Kr 85 , can be stably incorporated into a wide variety of solids and used as tracers or a kind of sensitive probe to measure chemical and physical phenomena. A general review is presented about the methods of incorporation with emphasis on ion bombardment and saturation. The problem of saturation of metal targets was correlated to certain properties in order to get a mathematical approach. Six properties were chosen as more significative to produce a simple model of saturation on experiments of ion implantation with Kr 85 at 45 KeV. The accuracy of the model is limited by the experimental error, the available data and its own simplicity. (Author) [pt

  10. Backbending in high spin states of 80Kr

    International Nuclear Information System (INIS)

    Kaushik, M.; Saxena, G.

    2014-01-01

    The study of high-spin states in Kr isotopes near A = 80 region has attracted a considerable interest in recent years. A variety of shapes, shape coexistence as well as backbending phenomenon have been studied in the many of Kr isotopes. In the case of 80 Kr, the high spin structure has been studied by Doring et al. rather extensively and has provided considerable insight into the structure of f-p-g shell nuclei and the competition between single-particle and collective degrees of freedom. Backbending phenomenon is reported in 80 Kr at ω = 0.5 MeV

  11. Kr-85 signatures for various plutonium production schemes

    Energy Technology Data Exchange (ETDEWEB)

    Stanoszek, Paul [Carl Friedrich von Weizsaecker-Centre for Science and Peace Research (Germany)

    2009-07-01

    Kr-85 is considered to be the best atmospheric indicator of unreported weapon-grade material production. This fact is based on the half-life of 10.76 years of Kr-85 and its chemical inactivity, which makes it even detectable after extended periods of cooling time. Kr-85 is produced as fission product during nuclear reactor operation and remains in the fuel until reprocessing starts. In order to determine the detectability of plutonium production the Kr-85 source term has to be assessed. The important issue of this presentation is the question on the minimum signal that an inspector can expect under the assumption that a proliferator minimizes his Kr-85 generation in order to circumvent a Kr-85 detection. A further assumption is that for nuclear weapon production a burn-up of typically around 2 MWd/kg is used. In addition, if clandestine plutonium production takes place, the source term might be used to estimate the amount of separated plutonium. The methodology of this study is based on a linkage between MCNPX and MATLAB. All results for actinide concentrations and Kr-85 are evaluated for different enrichments of U-235 and compared to known literature data. The Kr-85 source term per kilogram plutonium depends on the enrichments. As a result the lowest Kr-85 source term is found for depleted uranium.

  12. Indirect processes in electron impact ionization of Kr24+ and Kr25+

    International Nuclear Information System (INIS)

    Chen, M.H.; Reed, K.J.

    1992-09-01

    Electron-impact ionization cross sections have been calculated for magnesiumlike Kr 24+ and sodiumlike Kr 25+ . Electron-impact ionization is an important atomic process in hot dense plasmas. It can affect the ionization balance, electron temperature, electron density, and level population in the plasma. In the past decade, theoretical and experimental studies have revealed that indirect processes can make significant contributions to the cross sections for electron impact ionization of positive ions. The most important indirect process is excitation of an inner-shell electron followed by Auger emission. Higher-order processes such as resonant excitation followed by sequential double Auger emission, can also contribute significantly. The contributions of excitation-autoionization and resonant excitation double autoionization (REDA) were included, in addition to the cross sections for direct ionization of a 3s electron. The calculations were carried out using the relativistic distorted wave methods and the multiconfiguration Dirac-Fock model. For Kr 25+ , the total cross section is about 5 times the direct ionization cross section. For the Kr 24+ , the indirect contribution is about 2.5 times the direct ionization cross section. The REDA process produces many strong resonances and contributes about 20% to the average ionization cross section

  13. Precipitation and measurements of precipitation

    NARCIS (Netherlands)

    Schmidt, F.H.; Bruin, H.A.R. de; Attmannspacher, W.; Harrold, T.W.; Kraijenhoff van de Leur, D.A.

    1977-01-01

    In Western Europe, precipitation is normal phenomenon; it is of importance to all aspects of society, particularly to agriculture, in cattle breeding and, of course, it is a subject of hydrological research. Precipitation is an essential part in the hydrological cycle. How disastrous local

  14. Laser technologies. KrF laser

    International Nuclear Information System (INIS)

    Owadano, Yoshiro; Okuda, Isao; Matsushima, Isao; Yashiro, Hidehiko; Matsumoto, Yuji

    1994-01-01

    Krypton-fluoride (KrF) laser is one of the promising driver for inertial confinement fusion because of its short wavelength, broad band width, high efficiency and capability of high repetition-rate operation. A high gain double-pass amplifier can yield a high, heavily saturated output intensity (5 to 6 times saturation intensity, > 10MW/cm 2 ) with nearly maximum efficiency (> 10%) and high stage gain (> 50) at the same time. The high gain can be achieved by cylindrical electron-beam pumping configuration without external magnetic field. Angular pulse multiplexing enables efficient pulse compression and amplification of beams with broad spectral width. The broad band width is required for irradiation smoothing methods, BRP (broad-band Random Phase Irradiation) or ISI (Induced Spatial Incoherence). Multi-kJ KrF laser, Super-ASHURA (Electrotechnical Laboratory, 8kJ), NIKE (at Naval Research Laboratory, 3kJ) and TITANIA (Rutherford Appleton Laboratory, 2kJ) are being developed and close to completion. (author)

  15. Precipitous Birth

    Directory of Open Access Journals (Sweden)

    Jennifer Yee

    2017-09-01

    Full Text Available Audience: This scenario was developed to educate emergency medicine residents on the management of a precipitous birth in the emergency department (ED. The case is also appropriate for teaching of medical students and advanced practice providers, as well as reviewing the principles of crisis resource management, teamwork, and communication. Introduction: Patients with precipitous birth require providers to manage two patients simultaneously with limited time and resources. Crisis resource management skills will be tested once baby is delivered, and the neonate will require assessment for potential neonatal resuscitation. Objectives: At the conclusion of the simulation session, learners will be able to manage women who have precipitous deliveries, as well as perform neonatal assessment and management. Method: This session was conducted using high-fidelity simulation, followed by a debriefing session and lecture on precipitous birth management and neonatal evaluation.

  16. Modeling of Kr-Xe discharge of excimer lamp

    Directory of Open Access Journals (Sweden)

    Belasri A.

    2013-03-01

    Full Text Available This paper reports the numerical simulation of Dielectric Barrier Discharge (DBD for Kr-Xe excilamp. The model of the discharge consists of three main modules: a plasma chemistry module, a circuit module and a Boltzmann equation module. The results predict the optimal operating conditions and describe the electrical and chemical properties of the KrXe* excimer lamp.

  17. Preliminary studies in sheep exposed to 85Kr atmospheres

    International Nuclear Information System (INIS)

    Andrew, F.D.; Willard, D.H.; Ballou, J.E.; Sikov, M.R.

    1977-01-01

    Accumulation of 85 Kr in arterial blood of sheep occurs within 10 min of inhalation exposure initiation, and disappears by 30 min after exposure termination. As reported for other species, 85 Kr concentrations in fat were approximately 10 times those in other tissues

  18. Disposition and biological effect of inhaled 85Kr

    International Nuclear Information System (INIS)

    Willard, D.H.; Ballou, J.E.; Ragan, H.A.; Gandolfi, A.J.

    1978-01-01

    Half-lives of approximately 5, 30, and 100 min were obtained for whole-body clearance of inhaled 85 Kr in beagle dogs. Analysis showed the highest partition coefficients in lungs, bone marrow, and fat. Circulating blood elements were not lowered permanently after 85 Kr exposures

  19. TCA precipitation.

    Science.gov (United States)

    Koontz, Laura

    2014-01-01

    Trichloroacetic acid (TCA) precipitation of proteins is commonly used to concentrate protein samples or remove contaminants, including salts and detergents, prior to downstream applications such as SDS-PAGE or 2D-gels. TCA precipitation denatures the protein, so it should not be used if the protein must remain in its folded state (e.g., if you want to measure a biochemical activity of the protein). © 2014 Elsevier Inc. All rights reserved.

  20. STRONTIUM PRECIPITATION

    Science.gov (United States)

    McKenzie, T.R.

    1960-09-13

    A process is given for improving the precipitation of strontium from an aqueous phosphoric-acid-containing solution with nickel or cobalt ferrocyanide by simultaneously precipitating strontium or calcium phosphate. This is accomplished by adding to the ferrocyanide-containing solution calcium or strontium nitrate in a quantity to yield a concentration of from 0.004 to 0.03 and adjusting the pH of the solution to a value of above 8.

  1. Electron beam pumped KrF lasers for fusion energy

    International Nuclear Information System (INIS)

    Sethian, J.D.; Friedman, M.; Giuliani, J.L. Jr.; Lehmberg, R.H.; Obenschain, S.P.; Kepple, P.; Wolford, M.; Hegeler, F.; Swanekamp, S.B.; Weidenheimer, D.; Welch, D.; Rose, D.V.; Searles, S.

    2003-01-01

    In this paper, we describe the development of electron beam pumped KrF lasers for inertial fusion energy. KrF lasers are an attractive driver for fusion, on account of their demonstrated very high beam quality, which is essential for reducing imprint in direct drive targets; their short wavelength (248 nm), which mitigates the growth of plasma instabilities; and their modular architecture, which reduces development costs. In this paper we present a basic overview of KrF laser technology as well as current research and development in three key areas: electron beam stability and transport; KrF kinetics and laser propagation; and pulsed power. The work will be cast in context of the two KrF lasers at the Naval Research Laboratory, The Nike Laser (5 kJ, single shot), and The Electra Laser (400-700 J repetitively pulsed)

  2. Analysis results of PAVE sampling of groundwaters from open boreholes OL-KR2, OL-KR7, OL-KR13 and OL-KR15 at Olkiluoto, Eurajoki, in 2004

    Energy Technology Data Exchange (ETDEWEB)

    Hirvonen, H. [Teollisuuden Voima Oyj, Eurajoki (Finland); Hatanpaa, E. [lnsinoeoeritoimisto Paavo Ristola Oy, Hollola (Finland)

    2005-12-15

    Four groundwater samples were collected at Olkiluoto from open boreholes OL-KR2, OL-KR7, OL-KR13 and OL-KR15 with pressurised water sampling equipment (PAVE) between summer 2004 and the beginning of 2005. The aim of the ground water sampling was to get information for the basis of the monitoring program during ONKALO construction. Sampling sections were mainly chosen so that the results of the chemical analyses from earlier studies could be used for comparison. This study is a part of Olkiluoto's monitoring programme (OMO). This study presents the sampling methods and the results of the laboratory analyses of groundwater samples from the open boreholes OL-KR2/328.5-330.5 m, OL-KR7/275.5- 289.5 m, OL-KR13/362-365 m and OL-KR15/241-245 m. The analytical results of the groundwater samplings are compared to earlier analytical results. According to Davis and De Wiest's ( 1967) classification, all ground water samples represent the borehole water type Na-Cl. All ground water samples were brackish ( 1000 mg/L < TDS < 1 0000 mg/L) according to Davis's ( 1964) TDS classification. Comparison of analytical results of the samples to earlier results shows that some changes have occurred between samplings. Other parameters, with couple of particular exceptions, have a downward trend, but bicarbonate concentration has increased in all boreholes. Concentrations of main parameters have changed most in OL-KR7 and OL-KR13 waters. Gas analyses results have not changed significantly, but increased carbon dioxide concentration is noticed in gas analysis results also. (orig.)

  3. Polarizability of Kr6+ from high-L Kr5+ fine-structure measurements

    International Nuclear Information System (INIS)

    Lundeen, S. R.; Fehrenbach, C. W.

    2007-01-01

    The transition between n=55 and n=109 Rydberg levels of Kr 5+ has been studied at high resolution using the resonant excitation stark ionization spectroscopy method. Resolved excitation of L=6, 7, 8, and 9 levels in n=55 lead to a determination of the fine-structure energies of these levels. Interpreted with the long-range polarization model, this leads to a measurement of the dipole polarizabilities of Zn-like Kr 6+ , α d =2.69(4)a 0 3 . Obtaining a value of the quadrupole polarizability from the data will require additional theoretical input. Factors contributing to the signal and noise levels in measurements of this type are discussed

  4. Solid Phases Precipitating in Artificial Urine in the Absence and Presence of Bacteria Proteus mirabilis—A Contribution to the Understanding of Infectious Urinary Stone Formation

    Directory of Open Access Journals (Sweden)

    Jolanta Prywer

    2018-04-01

    Full Text Available Magnesium ammonium phosphate hexahydrate, called struvite, is the dominant component of infectious urinary stones. In addition to struvite, infectious urinary stones include solid phases with poor crystallinity as well as amorphous matter. This article is devoted to the analysis of these solid phases, because they have not been characterized well until now. The solid phases tested were obtained from artificial urine in the absence and presence of Proteus mirabilis. The solid phases were characterized by different techniques (X-ray Diffraction, Energy Dispersive X-ray, Scanning Electron Microscopy, as well as Raman and Infrared Spectroscopies. According to the results these phases are carbonate apatite (CA, hydroxylapatite (HAP, amorphous calcium carbonate (ACC, amorphous calcium phosphate (ACP and/or amorphous carbonated calcium phosphate (ACCP. Carbonate apatite and hydroxylapatite may occur in non-stoichiometric forms, i.e., various anions can be substituted for CO32−, OH−, and PO43− groups in them. The non-stoichiometry of carbonate apatite and hydroxylapatite also implies a deficiency of calcium ions, i.e., calcium ions may be partially replaced by other cations. Experimental techniques and chemical speciation analysis demonstrate that the presence of magnesium influences the formation of CA and HAP.

  5. New energy level identifications in Kr VI

    International Nuclear Information System (INIS)

    Tauheed, A.; Pinnington, E.H.; Ansbacher, W.; Kernahan, J.A.

    1990-01-01

    Beam-foil delayed spectra from 89.0 to 101.0 nm are used to identify the intercombination lines connecting the 4s4p 2 4 P and 4s 2 4p 2 P levels in Kr VI. The existing analysis is extended to include the 4s 2 5s 2 S 1/2 , 4f 2 F 5/2 , 2 F 7/2 , 4p 3 2 D 3/2 , 2 D 5/2 , 2 P 3/2 , 4 S 3/2 and 4s4p 2 4 P 1/2 , 4 P 3/2 , 4 P 5/2 levels. Lifetime measurements for the 4s4p 2 4 P 1/2 , 4 P 5/2 , 4p 3 2 D 3/2 and 2 D 5/2 levels are also discussed in support of these assignments. (orig.)

  6. Completion of Kr-81 and Kr-85 Analysis Development for Hydrogeology and Testing its Validity by Assessing Aquifer Recharge Rates

    International Nuclear Information System (INIS)

    Thonnard, Norbert

    2007-01-01

    The overall objective was to complete the development of a RIMS-based analytical technique to determine the concentration of the rare krypton radioisotopes, 81Kr and 85Kr, in samples of interest to the geoscience and planetary science community The key to RIMS is the use of tunable lasers to selectively and efficiently excite by resonant photon absorption atomic states unique to the chosen element. Ionization of the specified element can then occur while excluding all other constituents of the sample, bringing detection limits down to the single-atom level. Combining RIMS with several steps of isotopic enrichment makes detection of a rare isotope, such as 81Kr, feasible. A complete process for groundwater samples consists of starting with (1) collecting the groundwater sample, (2) degassing the water sample, (3) separating Kr from the recovered gases, (4 and 5) two isotopic enrichments reducing interfering isotopes by >109, and (6) detecting the rare krypton isotope using RIMS in a time-of-flight system. Required water sample size is 20 liters for 81Kr and 10 to 3 liters for 85Kr. Weak links in the above steps were to be identified and rectified. Most of the troublesome issues were resolved, but unfortunately, two key difficulties could not be resolved with the available resources, so the overall, final goal of completing a suite of measurements was not achieved. In spite of this, valuable collaborations were established to demonstrate the value of 81Kr and 85Kr measurements in two critical applications, the future site of a nuclear waste repository, where high efficiency 81Kr measurements would allow groundwater dating of low-yield formations, and a multi-method analysis of potential contamination inflow into a large municipal water system, where the simplicity of interpretation of 85Kr measurements could become a valuable future interpretive tool. Therefore, samples were collected anyway, and processing started using the working parts of the method, so that

  7. EUV emission from Kr and Xe capillary discharge plasmas

    International Nuclear Information System (INIS)

    Juschkin, L.; Ellwi, S.; Kunze, H-J.; Chuvatin, A.; Zakharov, S.V.

    2002-01-01

    Kr and Xe plasmas are very intensive emitters in the spectral range of 100-150 A, which is relevant for a number of applications (for example microlithography). We present investigations of the extreme utraviolet (EUV) emission from a slow capillary discharge with Kr and Xe fillings. The emission of Kr ions (Kr VIII to Kr XI) within the range of 70-150 A consists of three bands of lines of about 10 A width with maxima at 116, 103 and 86 A. Xe emission bands of about 15 A width have their maxima at 136 and 115 A (Xe IX to Xe XII). The radiation duration in this spectral range is ∼150 ns for both elements. At the optimum conditions, the Kr emission at 103 A is 2-3 times more intense than the Xe emission at 136 A. The measured spectral energy of Kr radiation is about 0.1 J sr -1 A -1 . Experimental results are compared with numerical modellings of the dynamics and emission of the capillary discharge plasma, which enables the determination of plasma parameters and the future use of the codes as additional instruments for plasma diagnostics. (author)

  8. Analysis of Selected Legacy 85Kr Samples

    Energy Technology Data Exchange (ETDEWEB)

    Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-09-02

    Legacy samples composed of 85Kr encapsulated in solid zeolite 5A material and five small metal tubes containing a mixture of the zeolite combined with a glass matrix resulting from hot isostatic pressing have been preserved. The samples were a result of krypton R&D encapsulation efforts in the late 1970s performed at the Idaho Chemical Processing Plant. These samples were shipped to Oak Ridge National Laboratory (ORNL) in mid-FY 2014. Upon receipt the outer shipping package was opened, and the inner package, removed and placed in a radiological hood. The individual capsules were double bagged as they were removed from the inner shipping pig and placed into individual glass sample bottles for further analysis. The five capsules were then x-ray imaged. Capsules 1 and 4 appear intact and to contain an amorphous mass within the capsules. Capsule 2 clearly shows the saw marks on the capsule and a quantity of loose pellet or bead-like material remaining in the capsule. Capsule 3 shows similar bead-like material within the intact capsule. Capsule 5 had been opened at an undetermined time in the past. The end of this capsule appears to have been cut off, and there are additional saw marks on the side of the capsule. X-ray tomography allowed the capsules to be viewed along the three axes. Of most interest was determining whether there was any residual material in the closed end of Capsule 5. The images confirmed the presence of residual material within this capsule. The material appears to be compacted but still retains some of the bead-like morphology. Based on the nondestructive analysis (NDA) results, a proposed path forward was formulated to advance this effort toward the original goals of understanding the effects of extended storage on the waste form and package. Based on the initial NDA and the fact that there are at least two breached samples, it was proposed that exploratory tests be conducted with the breached specimens before opening the three intact

  9. Estimation of radiation hazard of global 85Kr

    International Nuclear Information System (INIS)

    Vasilenko, I.Ya.; Moskalev, Yu.I.; Istomina, A.G.

    1979-01-01

    The data on sources and levels of the 85 Kr biosphere contamination are presented on the basis of generalization and analysis of literature. The potential irradiation doses for people are calculated and the biological estimation of the hazard of 85 Kr accumulation in the atmosphere up to 2050 is given taking into account the prospects for development of nuclear power engineering. The basis of the estimation is the radionuclide blastomogeneous and genetic effect. The conclusion is made that the prospects for development of nuclear power engineering do not lead to any sufficient increase in the number of malignant tumors and genetic abnormalities caused by 85 Kr radiation comparing with their natural frequency

  10. Precipitation Matters

    Science.gov (United States)

    McDuffie, Thomas

    2007-01-01

    Although weather, including its role in the water cycle, is included in most elementary science programs, any further examination of raindrops and snowflakes is rare. Together rain and snow make up most of the precipitation that replenishes Earth's life-sustaining fresh water supply. When viewed individually, raindrops and snowflakes are quite…

  11. Observation of site-specific decay processes in Ar-Kr mixed clusters following K-shell excitation of Kr

    International Nuclear Information System (INIS)

    Nagaya, K.; Murakami, H.; Iwayama, H.; Yao, M.

    2008-01-01

    Multiple ion coincidence momentum imaging measurements have been performed for an Ar-Kr mixed rare-gas cluster with an average cluster size = 100 in the 1s threshold region of Kr. The signals resulting due to the photoabsorption by Kr have been extracted on the basis of the difference in the spectra between 14.08 and 14.50 keV, i.e., on both sides of the 1s threshold for Kr. The time-of-flight spectra for the clusters reveal that multiply charged cluster ions produced as a result of inner-core excitation emit many singly charged ions such as Kr + , Ar + , ArKr + , and Ar 2 + . The abundance of daughter ions suggests the transfer of positive charges from the X-ray absorbing atom to the surrounding atoms before the Coulomb explosion is suggested from. The momentum of daughter ions is deduced from the time-of-flight and position data, and the momentum distribution shows the characteristic size dependence of the ions on the number of coincidence signals N coin , i.e., the average momentum of the Ar + ions increases with N coin , while that of the Kr + ions decreases. The N coin dependence of momentum is interpreted according to the site-dependent decay processes

  12. Osseointegration of loaded dental implant with KrF laser hydroxylapatite films on Ti6Al4V alloy by minipigs

    Czech Academy of Sciences Publication Activity Database

    Dostálová, T.; Jelínek, Miroslav; Grivas, C.

    2001-01-01

    Roč. 6, č. 2 (2001), s. 239-243 ISSN 1083-3668 Institutional research plan: CEZ:AV0Z1010914 Keywords : osseointegration * titanium alloy * KrF laser Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.292, year: 2001

  13. Status of the Nike KrF laser

    International Nuclear Information System (INIS)

    Lehmberg, R.H.; Bodner, S.E.; Gerber, K.A.; Kearney, K.J.; McLean, E.A.; Obenschain, S.P.; Pawley, C.J.; Pronko, M.S.; Sethian, J.D.; Stamper, J.A.; Sullivan, C.A.; Webster, W.D.; McGeoch, M.W.

    1995-01-01

    This document presents the main features of the NIKE laser currently under development at the Naval Research Laboratory. The aim of this KrF laser is to address technological and physics issues of direct-drive laser fusion. (TEC)

  14. High efficiency Dual-Cycle Conversion System using Kr-85.

    Science.gov (United States)

    Prelas, Mark A; Tchouaso, Modeste Tchakoua

    2018-04-26

    This paper discusses the use of one of the safest isotopes known isotopes, Kr-85, as a candidate fuel source for deep space missions. This isotope comes from 0.286% of fission events. There is a vast quantity of Kr-85 stored in spent fuel and it is continually being produced by nuclear reactors. In using Kr-85 with a novel Dual Cycle Conversion System (DCCS) it is feasible to boost the system efficiency from 26% to 45% over a single cycle device while only increasing the system mass by less than 1%. The Kr-85 isotope is the ideal fuel for a Photon Intermediate Direct Energy Conversion (PIDEC) system. PIDEC is an excellent choice for the top cycle in a DCCS. In the top cycle, ionization and excitation of the Kr-85:Cl gas mixture (99% Kr and 1% Cl) from beta particles creates KrCl* excimer photons which are efficiently absorbed by diamond photovoltaic cells on the walls of the pressure vessels. The benefit of using the DCCS is that Kr-85 is capable of operating at high temperatures in the primary cycle and the residual heat can then be converted into electrical power in the bottom cycle which uses a Stirling Engine. The design of the DCCS begins with a spherical pressure vessel of radius 13.7 cm with 3.7 cm thick walls and is filled with a Kr-85:Cl gas mixture. The inner wall has diamond photovoltaic cells attached to it and there is a sapphire window between the diamond photovoltaic cells and the Kr-85:Cl gas mixture which shields the photovoltaic cells from beta particles. The DCCS without a gamma ray shield has specific power of 6.49 W/kg. A removable 6 cm thick tungsten shield is used to safely limit the radiation exposure levels of personnel. A shadow shield remains in the payload to protect the radiation sensitive components in the flight package. The estimated specific power of the unoptimized system design in this paper is about 2.33 W/kg. The specific power of an optimized system should be higher. The Kr-85 isotope is relatively safe because it

  15. Determination of 24 personal care products in fish bile using hybrid solvent precipitation and dispersive solid phase extraction cleanup with ultrahigh performance liquid chromatography-tandem mass spectrometry and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Yao, Li; Lv, Yin-Zhi; Zhang, Li-Juan; Liu, Wang-Rong; Zhao, Jian-Liang; Liu, You-Sheng; Zhang, Qian-Qian; Ying, Guang-Guo

    2018-05-25

    Personal care products (PCPs) are ubiquitous in aquatic environments owing to the continuous discharge of domestic wastewater from highly urbanized regions. These PCPs can be adsorbed by fish and thereafter usually enter the bile of the fish through biliary excretion. In this study, a sensitive method based on a combination of hybrid solvent precipitation and dispersive solid phase extraction (d-SPE) purification was developed to simultaneously extract and detect 24 PCPs, namely, 16 biocides, 4 synthetic musks, and 4 benzotriazoles, from fish bile. Hybrid precipitation on solid phase extraction (SPE) tubes was applied to remove phospholipids and proteins, and a d-SPE procedure was used for further purification. The extraction solvents for the hybrid precipitation/SPE tubes and d-SPE materials were optimized. The method performance for bile samples both with and without enzyme hydrolysis using β-glucuronidase/aryl-sulfatase were validated. The 24 PCPs in fish bile were spiked with standard concentrations of 10 ng/mL, 20 ng/mL, 100 ng/mL, and 200 ng/mL to evaluate recoveries, which ranged from 70 to 120% for 16, 16, 22, and 21 analytes with hydrolysis, respectively, and 70-120% for 14, 15, 23, and 23 analytes without hydrolysis, respectively. The quantification limits for target PCPs were in the range 0.26-7.38 ng/mL [excluding musk xylene (MX) and musk ketone (MK)] and 0.20-9.48 ng/mL (excluding MX and MK) for bile samples with and without enzyme hydrolysis, respectively. After enzyme hydrolysis, 12 PCPs were detected in bile from fish collected from the Yangtze River, with a maximum detected concentration of 460 ng/mL, for triclosan (TCS). The hydrolysis reaction indicated that high percentages of glucuronide and sulfate metabolites for some PCPs, i.e. four parabens and TCS, existed in the bile. Copyright © 2018 Elsevier B.V. All rights reserved.

  16. Pulmonary ventilation studies of asthmatic children with Kr-81m

    International Nuclear Information System (INIS)

    Uchiyama, Guio; Hotta, Toshiko; Arimizu, Noboru; Sugimoto, Kazuo.

    1979-01-01

    Krypton-81 m gas was eluted from the 81 Rb-sup(81m)Kr generator by using compressed air or oxygen as an eluting agent. The continuous inhalation of mixed gas of sup(81m)Kr and air or oxygen with the use of a scintillation camera produced a pulmonary image of which density was proportional to regional ventilation. Because of short half life of sup(81m)Kr (13 seconds), exhaled gas was not necessary to be trapped by the charcoal filter, and the several pulmonary views of a patient could readily be available in a short period of time. The great advantage of sup(81m)Kr generator was found in use for the studies of small children who were not usually cooperative to medical examination. Thirty seven patients with bronchial asthma of any state were so far studied. Their ages ranged from 3 to 15 years old. Studies revealed the definite ventilation defects in scans of patients with asthmatic attack. Re-scans right after the use of bronchodilators showed marked improvement of the ventilation defects. Exercise-induced asthma (EIA) was easily identified by the sup(81m)Kr ventilation study. After premedications for EIA with disodium cromoglicate, the next exercises produced less or no ventilation defects, and the preventive effect could be individually examined. The sup(81m)Kr ventilation study was also used for estimating the patient's sensitivity to provokative substances of bronchial asthma. House dust was continuously inhaled with sup(81m)Kr gas by patients. The threshold dose of house dust of disclosing ventilation defects in scans was definitely less than that of provokating the symptom of asthmatic attack. The sensitive sup(81m)Kr ventilation study could be another provokative test which induces no clinical symptoms. (author)

  17. Pulmonary ventilation studies of asthmatic children with Kr-81m

    Energy Technology Data Exchange (ETDEWEB)

    Uchiyama, G; Hotta, T; Arimizu, N [Chiba Univ. (Japan). School of Medicine; Sugimoto, K

    1979-05-01

    Krypton-81 m gas was eluted from the /sup 81/Rb-sup(81m)Kr generator by using compressed air or oxygen as an eluting agent. The continuous inhalation of mixed gas of sup(81m)Kr and air or oxygen with the use of a scintillation camera produced a pulmonary image of which density was proportional to regional ventilation. Because of short half life of sup(81m)Kr (13 seconds), exhaled gas was not necessary to be trapped by the charcoal filter, and the several pulmonary views of a patient could readily be available in a short period of time. The great advantage of sup(81m)Kr generator was found in use for the studies of small children who were not usually cooperative to medical examination. Thirty seven patients with bronchial asthma of any state were so far studied. Their ages ranged from 3 to 15 years old. Studies revealed the definite ventilation defects in scans of patients with asthmatic attack. Re-scans right after the use of bronchodilators showed marked improvement of the ventilation defects. Exercise-induced asthma (EIA) was easily identified by the sup(81m)Kr ventilation study. After premedications for EIA with disodium cromoglicate, the next exercises produced less or no ventilation defects, and the preventive effect could be individually examined. The sup(81m)Kr ventilation study was also used for estimating the patient's sensitivity to provokative substances of bronchial asthma. House dust was continuously inhaled with sup(81m)Kr gas by patients. The threshold dose of house dust of disclosing ventilation defects in scans was definitely less than that of provokating the symptom of asthmatic attack. The sensitive sup(81m)Kr ventilation study could be another provokative test which induces no clinical symptoms. (author).

  18. Low-lying level structure of 73Kr

    International Nuclear Information System (INIS)

    Moltz, D.M.; Robertson, J.D.; Norman, E.B.; Burde, J.; Beausang, C.W.

    1993-01-01

    We have used the 40 Ca( 36 Ar, 2pn) reaction to study the low-lying level structure of 73 Kr. By utilizing a bombarding energy at the Coulomb barrier, the relative cross section for this channel was enhanced to a few percent of the total reaction cross section. Levels in 73 Kr were assigned based primarily upon observed neutron-gamma-gamma coincidences and upon comparisons of these newly assigned transition cross sections with those from known nuclei. (orig.)

  19. The NIKE KrF laser program

    International Nuclear Information System (INIS)

    Sethian, J.D.; Bodner, S.E.; Gerber, K.A.; Lehmberg, R.H.; McLean, E.A.; Obenschain, S.P.; Pawley, C.J.; Pronko, M.S.; Stamper, J.A.; Deniz, A.V.; Hardgrove, J.; Lehecka, T.; McGeoch, M.W.

    1994-01-01

    NIKE is a large angularly multiplexed Krypton-Fluoride (KrF) laser under development at the Naval Research Laboratory. It is designed to explore the technical and physics issues of direct drive laser fusion. When completed, NIKE will deliver 2--3 kJ of 248 nm light in a 4 nsec pulse with intensities exceeding 2x10 14 W/cm 2 onto a planar target. Spatially and temporally incoherent light will be used to reduce the ablation pressure nonuniformities to less than 2% in the target focal plane. These parameters are predicted to be those required for a high gain ICF pellet. The NIKE system consists of a commercial oscillator/amplifier front end, an array of gas discharge amplifiers, two electron beam pumped amplifiers (one with a 20x20 cm 2 aperture, the other with a 60x60 cm 2 aperture) and the optics required to relay, encode, and decode the beam. Approximately two-thirds of the system is operational and currently undergoing tests. The output of the smaller e-beam system, the 20 cm Amplifier, exceeds both the uniformity and energy required to drive the final e-beam system, the 60 cm Amplifier. The pulsed power components of the 60 cm Amplifier have been built, and initial tests show the electron beam deposited by the system meets the laser requirements for pumping uniformity and energy deposition. copyright 1994 American Institute of Physics

  20. Electron impact excitation of Kr XXXII

    Science.gov (United States)

    Aggarwal, K. M.; Keenan, F. P.; Lawson, K. D.

    2009-09-01

    Collision strengths (Ω) have been calculated for all 7750 transitions among the lowest 125 levels belonging to the 2s2p,2s2p,2p,2s3ℓ,2s2p3ℓ, and 2p3ℓ configurations of boron-like krypton, Kr XXXII, for which the Dirac Atomic R-matrix Code has been adopted. All partial waves with angular momentum J⩽40 have been included, sufficient for the convergence of Ω for forbidden transitions. For allowed transitions, a top-up has been included in order to obtain converged values of Ω up to an energy of 500 Ryd. Resonances in the thresholds region have been resolved in a narrow energy mesh, and results for effective collision strengths (ϒ) have been obtained after averaging the values of Ω over a Maxwellian distribution of electron velocities. Values of ϒ are reported over a wide temperature range below 107.3K, and the accuracy of the results is assessed. Values of ϒ are also listed in the temperature range 7.3⩽logTe(K)⩽9.0, obtained from the nonresonant collision strengths from the Flexible Atomic Code.

  1. Geophysical drillhole logging and imaging of drillholes OL-KR54, OL-KR55 and OL-KR55B at Olkiluoto in 2010 and 2011

    International Nuclear Information System (INIS)

    Tarvainen, A.-M.; Heikkinen, E.

    2011-08-01

    Suomen Malmi Oy conducted geophysical drillhole logging as well as optical and acoustic imaging of the drillholes OL-KR54, OL-KR55 and OL-KR55B at the Olkiluoto site in Eurajoki between August 2010 and January 2011. The survey is a part of Posiva Oy's detailed investigation program for the final disposal of spent nuclear fuel. The assignment included the field work and data processing. The report describes field operation, equipment as well as processing procedures and shows the obtained results and an analysis of their quality in the appendices. New focused resistivity, susceptibility, natural gamma and density probes were tested and compared with old probes. This report describes the major features of new probes and the comparison with old probes. The raw and processed data are delivered digitally in WellCAD, PDF and Excel format. (orig.)

  2. Hydraulic conductivity measurements with HTU at Eurajoki, Olkiluoto, drillholes OL-KR19, OL-KR45 and OL-KR46 in 2009 and 2010

    Energy Technology Data Exchange (ETDEWEB)

    Haemaelaeinen, H. [Geopros Oy, Helsinki (Finland)

    2011-10-15

    As a part of the site investigations for the disposal of spent nuclear fuel, hydraulic conductivity measurements were carried out with HTU-equipment in drillholes OL-KR19, OL-KR45 and OL-KR46 at Eurajoki, Olkiluoto. The objective was to investigate the distribution of the hydraulic conductivity in the surrounding bedrock volume. Measurements were carried out during 2009 and 2010. The total length of the borehole OL-KR19 is 544,34 m, 241,80 m of which was covered by 121 standard tests with 2 m packer separation as specified in the measurement plan. Respectively, OL-KR45 is 1023,30 m long and 63 similar tests were made in it covering 126,00 m of the hole and OL-KR46 600,10 m long, 151 tests made covering 301,35 m. The measured sections are around the depths of the planned repository. Double-packer constant-head method was used throughout with nominal 200 kPa overpressure. Injection stage lasted normally 20 minutes and fall-off stage 10 minutes. The tests were often shortened if there were clear indications that the hydraulic conductivity is below the measuring range of the system. The pressure in the test section was let to stabilise at least 5 min before injection. In some test sections the test stage times were extended. Two transient (Horner and 1/Q) interpretations and one stationary- state (Moye) interpretation were made in-situ immediately after the test. The Hydraulic Testing Unit (HTU-system) is owned by Posiva Oy and it was operated by Geopros Oy. (orig.)

  3. Possible 85Kr influence on the plant metabolism. Investigation of inert gas 85Kr interaction with plants

    International Nuclear Information System (INIS)

    Butkus, D.

    1999-01-01

    Model experiments have shown that inert gas 85 Kr is accumulated by plants. The aim of the work was to determine the way of the capture of inert gas by growing plants: either only through their overground part from air or in addition through their overground part from air or in addition through roots which accumulate water dissolved materials. For this purpose potatoes were grown in the chamber where the 85 Kr volume activity was (3.6±0.1)*10 6 Bq*m -3 . It was determined that 85 Kr gas accumulation was greater in those plant parts which grow faster and are further from the soil. Measurement results of 85 Kr activity of a potato tuber slightly differed from the environment background activity. It shows that the main penetration of inert gas into the plant occurred by absorption from air. (author)

  4. Muonium localization in solid krypton

    International Nuclear Information System (INIS)

    Storchak, V.; Cox, S.F.J.; Brewer, J.H.; Morris, G.D.

    1995-06-01

    Muonium spin relaxation in zero, longitudinal and transverse magnetic fields has been studied in solid and liquid krypton in the temperature range from 2 K to 120 K. In the solid at low temperatures, the spin dynamics exhibit features characteristic of a magnetically dilute crystal, permitting measurements of exceptionally low muonium diffusion rates. At the lowest temperatures, a static Kubo-Toyabe relaxation function has been observed for the first time for the atomic muonium state, indicating strong interstitial localization in the Kr lattice at low temperatures; muonium is determined to be localized at the tetrahedral interstitial position. At high temperatures, muonium diffusion in solid Kr exhibits a non-classical behaviour. (author). 31 refs., 6 figs

  5. Predicted versus observed cosmic-ray-produced noble gases in lunar samples: improved Kr production ratios

    International Nuclear Information System (INIS)

    Regnier, S.; Hohenberg, C.M.; Marti, K.; Reedy, R.C.

    1979-01-01

    New sets of cross sections for the production of krypton isotopes from targets of Rb, Sr, Y, and Zr were constructed primarily on the bases of experimental excitation functions for Kr production from Y. These cross sections were used to calculate galactic-cosmic-ray and solar-proton production rates for Kr isotopes in the moon. Spallation Kr data obtained from ilmenite separates of rocks 10017 and 10047 are reported. Production rates and isotopic ratios for cosmogenic Kr observed in ten well-documented lunar samples and in ilmenite separates and bulk samples from several lunar rocks with long but unknown irradiation histories were compared with predicted rates and ratios. The agreements were generally quite good. Erosion of rock surfaces affected rates or ratios for only near-surface samples, where solar-proton production is important. There were considerable spreads in predicted-to-observed production rates of 83 Kr, due at least in part to uncertainties in chemical abundances. The 78 Kr/ 83 Kr ratios were predicted quite well for samples with a wide range of Zr/Sr abundance ratios. The calculated 80 Kr/ 83 Kr ratios were greater than the observed ratios when production by the 79 Br(n,γ) reaction was included, but were slightly undercalculated if the Br reaction was omitted; these results suggest that Br(n,γ)-produced Kr is not retained well by lunar rocks. The productions of 81 Kr and 82 Kr were overcalculated by approximately 10% relative to 83 Kr. Predicted-to-observed 84 Kr/ 83 ratios scattered considerably, possibly because of uncertainties in corrections for trapped and fission components and in cross sections for 84 Kr production. Most predicted 84 Kr and 86 Kr production rates were lower than observed. Shielding depths of several Apollo 11 rocks were determined from the measured 78 Kr/ 83 Kr ratios of ilmenite separates. 4 figures, 5 tables

  6. Radioactive 85Kr in krypton enriched with a light isotope

    International Nuclear Information System (INIS)

    Kuz'minov, V.V.; Novikov, V.M.; Pomanskii, A.A.; Pritychenko, B.V.; Vieiar, J.; Garcia, E.; Morales, A.; Morales, J.; Nunes-Lagos, R.; Piumendon, J.

    1993-01-01

    Radioactive krypton 85, a product of nuclear power generation, is known to be accumulating in the atmosphere continuously. Its volumetric activity in natural krypton is 700-800 Bq/liter. This can cause difficulties, e.g., in the fabrication of nuclear radiation detector for high-mass krypton. Krypton with a reduced 85 Kr content can be obtained by isotope separation. As part of an experiment to look for two-positron decay and conversion of an atomic electron to a positron in 78 Kr, Saenz measured the 85 Kr content in 78 Kr-enriched krypton. A mixture of two 85 Kr samples was used as the working substance of a cylindrical ionization chamber. The useful volume (1.33 liter) of the chamber contained 35.3 liters of gas at ∼2.5 kPa. The energy resolution of the detector at an energy of 0.511 MeV was 3.8%. The measurements were made in a passive lead shield 20 cm thick in an underground laboratory at a depth of 675 m water equivalent. Results are presented for counting rates in low-energy regions, contribution of krypton-85 to background, and the volumetric activity of krypton-85

  7. Cross-Section Measurements of the Kr86(γ,n) Reaction to Probe the s-Process Branching at Kr85

    Science.gov (United States)

    Raut, R.; Tonchev, A. P.; Rusev, G.; Tornow, W.; Iliadis, C.; Lugaro, M.; Buntain, J.; Goriely, S.; Kelley, J. H.; Schwengner, R.; Banu, A.; Tsoneva, N.

    2013-09-01

    We have carried out photodisintegration cross-section measurements on Kr86 using monoenergetic photon beams ranging from the neutron separation energy, Sn=9.86MeV, to 13 MeV. We combine our experimental Kr86(γ,n)Kr85 cross section with results from our recent Kr86(γ,γ') measurement below the neutron separation energy to obtain the complete nuclear dipole response of Kr86. The new experimental information is used to predict the neutron capture cross section of Kr85, an important branching point nucleus on the abundance flow path during s-process nucleosynthesis. Our new and more precise Kr85(n,γ)Kr86 cross section allows us to produce more precise predictions of the Kr86 abundance from s-process models. In particular, we find that the models of the s process in asymptotic giant branch stars of mass <1.5M⊙, where the C13 neutron source burns convectively rather than radiatively, represent a possible solution for the highest Kr86∶Kr82 ratios observed in meteoritic stardust SiC grains.

  8. An improved method for {sup 85}Kr analysis by liquid scintillation counting and its application to atmospheric {sup 85}Kr determination

    Energy Technology Data Exchange (ETDEWEB)

    Momoshima, Noriyuki, E-mail: momoshima.noriyuki.551@m.kyushu-u.ac.j [Radioisotope Center, Kyushu University, 6-10-1 Hakozaki, Higashi-ku, Fukuoka 812-8581 (Japan); Inoue, Fumio [Graduate School of Science, Kyushu University, 6-10-1Hakozaki, Higashi-ku, Fukuoka 812-8581 (Japan); Sugihara, Shinji [Radioisotope Center, Kyushu University, 6-10-1 Hakozaki, Higashi-ku, Fukuoka 812-8581 (Japan); Shimada, Jun [Graduate School of Science and Technology, Kumamoto University, 2-39-1 Kurokami, Kumamoto 860-8555 (Japan); Taniguchi, Makoto [Research Institute for Humanity and Nature, 457-4 Motoyama Kamigamo, Kita-ku, Kyoto 603-8047 (Japan)

    2010-08-15

    Atmospheric {sup 85}Kr concentration at Fukuoka, Japan was determined by an improved {sup 85}Kr analytical method using liquid scintillation counting (LSC). An average value of 1.54 {+-} 0.05 Bq m{sup -3} was observed in 2008, which is about two times that measured in 1981 at Fukuoka, indicating a 29 mBq y{sup -1} rate of increase as an average for these 27 years. The analytical method developed involves collecting Kr from air using activated charcoal at liquid N{sub 2} temperature and purifying it using He at dry ice temperature, followed by Kr separation by gas chromatography. An overall Kr recovery of 76.4 {+-} 8.1% was achieved when Kr was analyzed in 500-1000 l of air. The Kr isolated by gas chromatography was collected on silica gel in a quartz glass vial cooled to liquid N{sub 2} temperature and the activity of {sup 85}Kr was measured with a low-background LS counter. The detection limit of {sup 85}Kr activity by the present analytical method is 0.0015 Bq at a 95% confidence level, including all propagation errors, which is equivalent with {sup 85}Kr in 1.3 l of the present air under the analytical conditions of 72.1% counting efficiency, 0.1597 cps background count rate, and 76.4% Kr recovery.

  9. Cross-section measurements of the 86Kr(γ,n) reaction to probe the s-process branching at 85Kr.

    Science.gov (United States)

    Raut, R; Tonchev, A P; Rusev, G; Tornow, W; Iliadis, C; Lugaro, M; Buntain, J; Goriely, S; Kelley, J H; Schwengner, R; Banu, A; Tsoneva, N

    2013-09-13

    We have carried out photodisintegration cross-section measurements on 86Kr using monoenergetic photon beams ranging from the neutron separation energy, S(n) = 9.86  MeV, to 13 MeV. We combine our experimental 86Kr(γ,n)85Kr cross section with results from our recent 86Kr(γ,γ') measurement below the neutron separation energy to obtain the complete nuclear dipole response of 86Kr. The new experimental information is used to predict the neutron capture cross section of 85Kr, an important branching point nucleus on the abundance flow path during s-process nucleosynthesis. Our new and more precise 85Kr(n,γ)86Kr cross section allows us to produce more precise predictions of the 86Kr abundance from s-process models. In particular, we find that the models of the s process in asymptotic giant branch stars of mass <1.5M⊙, where the 13C neutron source burns convectively rather than radiatively, represent a possible solution for the highest 86Kr:82Kr ratios observed in meteoritic stardust SiC grains.

  10. The use of Kr-81m in ventilation imaging

    International Nuclear Information System (INIS)

    Pommet, R.; Therain, F.

    1982-01-01

    Radioactive gases are very useful in the study of pulmonary disorders because they allow an assessment of regional lung function. The most widely used radioactive gases are Xe-133 and, more recently, Kr-81m. This paper is a review of the physical characteristics of Kr-81m, its production from the parent Rb-81, the different methods to produce Rb-81, the different types of generators which can be used in hospitals, and the clinical applications of pulmonary ventilation imaging. The paper suggests that Kr-81m offers several advantages over previous methods that used Xe-133 due to its improved spatial resolution, its capacity to provide superimposable ventilation and perfusion images in multiple projections, and its total lung dose which is ten times lower than that of Xe-133

  11. Lifetime measurements in N=Z 72Kr

    Science.gov (United States)

    Andreoiu, C.; Svensson, C. E.; Austin, R. A. E.; Carpenter, M. P.; Dashdorj, D.; Finlay, P.; Freeman, S. J.; Garrett, P. E.; Görgen, A.; Greene, J.; Grinyer, G. F.; Hyland, B.; Jenkins, D.; Johnston-Theasby, F.; Joshi, P.; Machiavelli, A. O.; Moore, F.; Mukherjee, G.; Phillips, A. A.; Reviol, W.; Sarantites, D. G.; Schumaker, M. A.; Seweryniak, D.; Smith, M. B.; Valiente-Dobón, J. J.; Wadsworth, R.

    2006-07-01

    High-spin states in the N=Z nucleus 72Kr have been populated in the 40Ca(40Ca, 2α)72Kr fusion-evaporation reaction at a beam energy of 165 MeV and using a thin isotopically enriched 40Ca target. The experiment, performed at Argonne National Laboratory close to Chicago, USA, employed the Gammasphere array for γ-ray detection coupled to the Microball array for charged particle detection. The previously observed bands in 72Kr were extended to a higher excitation energy of ~24 MeV and higher angular momentum of 30planck. Using the Doppler-shift attenuation method, the lifetimes of high-spin states were measured for the first time in order to investigate deformation changes associated with the g9/2 proton and neutron alignments in this N=Z nucleus. An excellent agreement with theoretical calculations including only standard t=1 np pairing was observed.

  12. Rheology of tetraphenylborate precipitate slurry

    International Nuclear Information System (INIS)

    Goren, I.D.; Martin, H.D.; McLain, M.A.

    1985-01-01

    The rheological properties of tetraphenylborate precipitate slurry were determined. This nonradioactive slurry simulates the radioactive tetraphenylborate precipitate generated at the Savannah River Plant by the In-Tank Precipitation Process. The data obtained in this study was applied in the design of slurry pumps, transfer pumps, transfer lines, and vessel agitation for the Defense Waste Processing Facility and other High Level Waste treatment projects. The precipitate slurry behaves as a Bingham plastic. The yield stress is directly proportional to the concentration of insoluble solids over the range of concentrations studied. The consistency is also a linear function of insoluble solids over the same concentration range. Neither the yield stress nor the consistency was observed to be affected by the presence of the soluble solids. Temperature effects on flow properties of the slurry were also examined: the yield stress is inversely proportional to temperature, but the consistency of the slurry is independent of temperature. No significant time-dependent effects were found. 4 refs., 4 figs., 3 tabs

  13. A Modified Method for Determination of Lumefantrine in Human Plasma by HPLC-UV and Combination of Protein Precipitation and Solid-Phase Extraction: Application to a Pharmacokinetic Study

    Directory of Open Access Journals (Sweden)

    Liusheng Huang

    2010-03-01

    Full Text Available An HPLC-UV method was developed and validated for the determination of lumefantrine in human plasma. Lumefantrine and its internal standard halofantrine were extracted from plasma samples using protein precipitation with acetonitrile (0.2% perchloric acid followed by solid-phase extraction with Hypersep C8 cartridges. Chromatographic separation was performed on a Zorbax SB-CN HPLC column (3.0 × 150 mm, 3.5 μm with water/methanol (0.1% TFA as the mobile phases in a gradient elution mode. Detection was performed using UV/vis detector at λ = 335 nm. The method showed to be linear over a range of 50–10,000 ng/mL with acceptable intra- and inter-day precision and accuracy. The mean recoveries were 88.2% for lumefatrine and 84.5% for the I.S. The internal standard halofantrine is readily available from commercial sources. This method was successfully applied to a pharmacokinetic interaction study between a first-line antimalarial combination (artemether—lumefantrine and antiretroviral therapy.

  14. Structural and luminescence properties of CaTiO{sub 3}:Eu{sup 3+} phosphor synthesized by chemical co-precipitation method for the application of solid state lighting devices

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Dhananjay Kumar, E-mail: dksism89@gmail.com; Manam, J., E-mail: jairam.manam@gmail.com [Department of Applied Physics, Indian School of Mines, Dhanbad-826004 (India)

    2016-05-06

    The present work report a series of trivalent Europium (Eu{sup 3+}) doped well crystallized perovskite CaTiO{sub 3} phosphors successfully synthesized by chemical co-precipitation method. The crystal structure was confirmed by X-ray diffraction (XRD) which is in good agreement with pure orthorhombic phase with space group Pbnm, and it also indicated that the incorporation of the dopant did not affect the crystal structure. The impact of doping on the photoluminescence performances of the sample has been investigated by emission, excitation, and diffuse reflectance spectra at the room temperature. Photoluminescence spectra of Eu{sup 3+} doped CaTiO{sub 3} nanophosphor revealed the characteristic emission peak around wavelength 618 nm in the visible region upon the excitation of near-UV light at wavelength 397 nm due to {sup 5}D{sub 0} → {sup 7}F{sub 2} transition in Eu{sup 3+}. It was further proved that the dipole– dipole interactions results in the concentration quenching of Eu{sup 3+} in CaTiO{sub 3}:Eu{sup 3+} nanophosphors. The elemental composition of sample carried out by energy dispersive spectroscopy (EDS). EDS analysis reveals that the Eu{sup 3+} doped successfully into host CaTiO{sub 3}. The experimental result reveals that prepared nanophosphor can be used in the application of solid state lighting devices.

  15. Long-term pumping test in borehole KR24 flow measurements

    Energy Technology Data Exchange (ETDEWEB)

    Rouhiainen, P.; Poellaenen, J. [PRG-Tec Oy, Espoo (Finland)

    2005-09-15

    The Difference Flow method can be used for the relatively fast determination of transmissivity and hydraulic head in fractures or fractured zones in cored boreholes. In this study, the Difference Flow method was used for hydraulic crosshole interference tests. The tests were performed in boreholes KR24 (pumped borehole) KR4, KR7, KR8, KRlO, KR14, KR22, KR22B, KR26, KR27, KR27B, KR28 and KR28B at Olkiluoto during the first and second quarters of 2004. The distance between the boreholes varies from approximately tens of meters to hundreds of meters. All the measurements were carried out in open boreholes, i.e. no packers were used. For interpretation, a normal single hole test was first performed in each borehole. Flow rates and drawdown were first measured both without pumping and with pumping the borehole under test. For practical reasons, the data set is neither complete nor similar in all tested boreholes. Connected flow to borehole KR24 was detected in all these boreholes. These flow responses were concentrated on a few zones. (orig.)

  16. A Simplified Numerical Study of the Kr/Cl2 Plasma Chemistry in Dielectric Barrier Discharge

    International Nuclear Information System (INIS)

    Bachir, N. Larbi Daho; Belasri, A.

    2013-01-01

    In this paper, the generation of excimers and exciplexe radiation in mixtures of rare gas with halogen by homogeneous dielectric barrier discharge (DBD) is investigated. The typical characteristics of an excilamp based on KrCl* exciplexe molecules and the kinetic processes for the formation and the decay of this molecules in the Kr/Cl 2 mixture are studied. The computer model developed is based on the Kr/Cl 2 mixture chemistry, the equivalent electric circuit and the Boltzmann equations. The importance in the kinetic processes of some species such as the metastable state of Krypton (Kr*( 3 P 0,2 )) and the negative ion of chloride (Cl − ) is considered. The results illustrate the time variations of charged species (n e , Kr + , Cl − , Cl + , Cl + 2 , Kr + 2 ), excited atoms and molecules (Kr*( 3 P 0,2 ), Kr*( 3 P 1 ), Cl*, Cl* 2 ), the excimers (Kr* 2 , KrCl*(B), KrCl*(C), Kr 2 Cl*) and the UV photon concentrations (in 222 nm, 235 nm, 258 nm and 325 nm range). The effects of chlorine concentration and the total gas pressure in the Kr-Cl 2 discharge on the electric parameters and radiation emissions are investigated. (low temperature plasma)

  17. Behavior of solid fission products in irradiated fuel

    International Nuclear Information System (INIS)

    Song, Ung Sup; Jung, Yang Hong; Kim, Hee Moon; Yoo, Byun Gok; Kim, Do Sik; Choo, Yong Sun; Hong, Kwon Pyo

    2004-01-01

    Many fission products are generated by fission events in UO 2 fuel under irradiation in nuclear reactor. Concentration of each fission product is changed by conditions of neutron energy spectrum, fissile material, critical thermal power, irradiation period and cooling time. Volatile materials such as Cs and I, the fission products, degrade nuclear fuel rod by the decrease of thermal conductivity in pellet and the stress corrosion cracking in cladding. Metal fission products (white inclusion) make pellet be swelled and decrease volume of pellet by densification. It seems that metal fission products are filled in the pore in pellet and placed between UO 2 lattices as interstitial. In addition, metal oxide state may change structural lattice volume. Considering behavior of fission products mentioned above, concentration of them is important. Fission products could be classified as bellows; solid solution in matrix : Sr, Zr, Nb, Y, La, Ce, Pr, Nd, Pm, Sm - metal precipitates : Mo, Tc, Ru, Rh, Pd, Ag, Cd, In, Sb, Te - oxide precipitates : Ba, Zr, Nb, Mo, (Rb, Cs, Te) - volatile and gases : Kr, Xe, Br, I, (Rb, Cs, Te)

  18. Ultrahigh-brightness KrF laser system for fast ignition studies

    International Nuclear Information System (INIS)

    Shaw, M.J.; Ross, I.N.; Hooker, C.J.; Dodson, J.M.; Hirst, G.J.; Lister, J.M.D.; Divall, E.J.; Kidd, A.K.; Hancock, S.; Damerell, A.R.; Wyborn, B.E.

    1999-01-01

    The main requirements for a fast igniter laser beam are reviewed and shown to favour short wavelength and ultrahigh brightness. These requirements are met by the new KrF laser system at Rutherford Appleton Laboratory called TITANIA. TITANIA uses two schemes to enhance the laser beam brightness. The first is chirped pulse amplification which is used to enhance brightness by compressing the pulse into the femtosecond region. In this mode TITANIA produces in the region of 250 mJ on target in 700 fs. The second mode of operation uses a Raman technique for beam combining and beam clean-up which is designed to give a single beam of 80 Joules on target in a pulselength of 60 ps. In this scheme the KrF wavelength is Raman shifted to 268 nm. The Raman amplifiers will use gaseous rather than solid windows and experiments which demonstrate their feasibility will be described. A concept for a reactor scale fast igniter beam using the Raman technique will be discussed. (orig.)

  19. Frozen orientation disorder and rotation excitation in solid mixtures of methane and krypton (neutron diffraction experiments)

    International Nuclear Information System (INIS)

    Grondey, S.

    1986-09-01

    The effect of a statistical replacement of CH 4 molecules by Kr atoms on the rotational states in solid methane has been examined. Obviously the anisotropic molecular interaction (octopole-octopole interaction) is disturbed in a way analogous to magnetic systems with random internal fields. Inelastic neutron scattering experiments on solid mixtures (CH 4 ) 1-x Kr x with 0≤x≤0.35 have been carried out, and simple models have been developed to interpret the spectra. (orig./BHO)

  20. Dmitri Krõmovist on saanud vaatemängumeister / Andres Laasik

    Index Scriptorium Estoniae

    Laasik, Andres, 1960-2016

    2006-01-01

    Vene lavastaja Dmitri Krõmovist ja tema lavastusest "Söör Vantes. Donki Hot" (Anatoli Vassiljevi Teater Draamakunstikool. Dmitri Krõmovi loomelaboratoorium), mida etendatakse festivalil "Talveöö unenägu 2006"

  1. Hybrid Ti:Sapphire / KrF laser facility GARPUN for combined subpicosecond/nanosecond laser-matter interaction studies

    International Nuclear Information System (INIS)

    Zvorykin, V.D.; Ionin, A.A.; Konyashcenko, A.V.; Levchenko, A.O.; Krokhin, O.N.; Mesyats, G.A.; Molchanov, A.G.; Rorulev, M.A.

    2006-01-01

    Complete test of publication follows. Hybrid laser facility consisting of Ti:Sapphire front end, 3ω converter, and e-beam-pumped large-aperture KrF amplifiers is under construction to generate combined sub-picosecond/nanosecond pulses in UV spectral range at 248-nm wavelength. This is a part of the Petawatt excimer laser project started at P.N. Lebedev Physical Institute. In comparison with commonly used solid-state chirped-pulse amplifiers (CPA), KrF amplifiers have following advantages: (i) low-density gaseous matter with three orders of magnitude lower non-linear refraction index has a small value of B-integral and negligible pulse distortion; (ii) short radiation lifetime τ r = 6 ns of the upper laser level of KrF(B-X) transition (with accounting for collisions τ c ∼ 2 ns), that means the population inversion is recovered each 2 ns during the pumping time, which is typically τ p ≥ 100 ns for technical reasons. Thus, it might be possible eliminating of very costly large-aperture compressor gratings and to amplify both short τ sh c and long τ long ≥ τ c pulses in the same amplifiers, as a short pulse does not affect the gain during the most of pumping. This gives a unique opportunity for realization of fast-ignition scheme in Inertial Confinement Fusion using large-scale KrF drivers. The Ti:Sapphire front end 'Start 248M' currently operates with the following parameters: rep rate 10 Hz, pulse energy and duration at fundamental wavelength (744 nm) > 8 mJ and 0.5 mJ and 0.4 mJ, 740 nm) and multi-pass amplifier (10 Hz, > 15 mJ, 740 nm), both pumped by 2ω pulsed Lotis LS-2134 Nd:YAG laser (10 Hz, 10 ns, 532 nm) with distributed energies of 5 and 70 mJ, two-gratings compressor, and 3ω converter with two BBO crystals and total efficiency 8%. EMG 150MSC Lambda Physik KrF laser is used afterwards to generate ns pulses and to amplify fs pulses in its two separate discharge chambers. Two e-beam pumped KrF amplifiers Berdysh and GARPUN with active volumes 10

  2. Investigation of the interaction of 85Kr with plants in model experiments

    International Nuclear Information System (INIS)

    Butkus, D.V.; Morkunas, G.S.; Bluvshtejn, D.Yu.; Styro, B.I.

    1988-01-01

    The method of investigation of the interaction of 85 Kr with plants is described using model experiments and data analysis. The dependencies of the coefficient of 85 Kr absorption by plants on the biological structure of the plant, the concentration of krypton-85 in the environment, the method of plant exposition in the environment with the 85 Kr admixture are provided. The time dependencies of 85 Kr desorption from plants are given. 4 refs.; 7 figs.; 3 tabs

  3. Observation of parametric instabilities in the quarter critical density region driven by the Nike KrF laser

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, J. L.; Kehne, D.; Brown, C. M.; Obenschain, S. P.; Serlin, V.; Schmitt, A. J. [U.S. Naval Research Laboratory, Washington DC 20375 (United States); Oh, J.; Lehmberg, R. H.; Mclean, E.; Manka, C. [Research Support Instruments, Lanham, Maryland 20905 (United States); Phillips, L. [Alogus Research Corporation, McLean, Virginia 22101 (United States); Afeyan, B. [Polymath Research, Inc., Pleasanton, California 94566 (United States); Seely, J.; Feldman, U. [Berkeley Research Associates, Inc., Beltsville, Maryland 20705 (United States)

    2013-02-15

    The krypton-fluoride (KrF) laser is an attractive choice for inertial confinement fusion due to its combination of short wavelength ({lambda}=248 nm), large bandwidth (up to 3 THz), and superior beam smoothing by induced spatial incoherence. These qualities improve the overall hydrodynamics of directly driven pellet implosions and should allow use of increased laser intensity due to higher thresholds for laser plasma instabilities when compared to frequency tripled Nd:glass lasers ({lambda}=351 nm). Here, we report the first observations of the two-plasmon decay instability using a KrF laser. The experiments utilized the Nike laser facility to irradiate solid plastic planar targets over a range of pulse lengths (0.35 ns{<=}{tau}{<=}1.25 ns) and intensities (up to 2 Multiplication-Sign 10{sup 15} W/cm{sup 2}). Variation of the laser pulse created different combinations of electron temperature and electron density scale length. The observed onset of instability growth was consistent with the expected scaling that KrF lasers have a higher intensity threshold for instabilities in the quarter critical density region.

  4. Observation of parametric instabilities in the quarter critical density region driven by the Nike KrF laser

    International Nuclear Information System (INIS)

    Weaver, J. L.; Kehne, D.; Brown, C. M.; Obenschain, S. P.; Serlin, V.; Schmitt, A. J.; Oh, J.; Lehmberg, R. H.; Mclean, E.; Manka, C.; Phillips, L.; Afeyan, B.; Seely, J.; Feldman, U.

    2013-01-01

    The krypton-fluoride (KrF) laser is an attractive choice for inertial confinement fusion due to its combination of short wavelength (λ=248 nm), large bandwidth (up to 3 THz), and superior beam smoothing by induced spatial incoherence. These qualities improve the overall hydrodynamics of directly driven pellet implosions and should allow use of increased laser intensity due to higher thresholds for laser plasma instabilities when compared to frequency tripled Nd:glass lasers (λ=351 nm). Here, we report the first observations of the two-plasmon decay instability using a KrF laser. The experiments utilized the Nike laser facility to irradiate solid plastic planar targets over a range of pulse lengths (0.35 ns≤τ≤1.25 ns) and intensities (up to 2×10 15 W/cm 2 ). Variation of the laser pulse created different combinations of electron temperature and electron density scale length. The observed onset of instability growth was consistent with the expected scaling that KrF lasers have a higher intensity threshold for instabilities in the quarter critical density region.

  5. Observation of parametric instabilities in the quarter critical density region driven by the Nike KrF laser

    Science.gov (United States)

    Weaver, J. L.; Oh, J.; Phillips, L.; Afeyan, B.; Seely, J.; Kehne, D.; Brown, C. M.; Obenschain, S. P.; Serlin, V.; Schmitt, A. J.; Feldman, U.; Lehmberg, R. H.; Mclean, E.; Manka, C.

    2013-02-01

    The krypton-fluoride (KrF) laser is an attractive choice for inertial confinement fusion due to its combination of short wavelength (λ =248 nm), large bandwidth (up to 3 THz), and superior beam smoothing by induced spatial incoherence. These qualities improve the overall hydrodynamics of directly driven pellet implosions and should allow use of increased laser intensity due to higher thresholds for laser plasma instabilities when compared to frequency tripled Nd:glass lasers (λ =351 nm). Here, we report the first observations of the two-plasmon decay instability using a KrF laser. The experiments utilized the Nike laser facility to irradiate solid plastic planar targets over a range of pulse lengths (0.35 ns≤τ≤1.25 ns) and intensities (up to 2×1015 W/cm2). Variation of the laser pulse created different combinations of electron temperature and electron density scale length. The observed onset of instability growth was consistent with the expected scaling that KrF lasers have a higher intensity threshold for instabilities in the quarter critical density region.

  6. Study of ΔI = 1 band in 83Kr

    International Nuclear Information System (INIS)

    Dey, Aparajita; Banerjee, P.; Ray, I.; Kshetri, R.; Bhattacharya, S.; Ganguly, Sourav . sgpresi@rediffmail.com; Muralithar, S.; Singh, R.P.; Kumar, R.; Bhowmik, R.K.

    2008-01-01

    Previously, the ΔI = 1 band in 83 Kr have been studied and reported in the literature. The lifetime results reported are smaller than those reported by about of a factor of two. A re-measurement of these level lifetimes has been attempted in the present work in view of the discrepancies in the reported results

  7. Performance of the Aurora KrF ICF laser system

    International Nuclear Information System (INIS)

    Jones, J.E.; Czuchlewski, S.J.; Turner, T.P.; Watt, R.G.; Thomas, S.J.; Netz, D.A.; Tallman, C.R.; Mack, J.M.; Figueira, J.F.

    1990-01-01

    Because short wavelength lasers are attractive for inertial confinement fusion (ICF), the Department of Energy is sponsoring work at Los Alamos National Laboratory in krypton-fluoride (KrF) laser technology. Aurora is a short-pulse, high-power, KrF laser system. It serves as an end-to-end technology demonstration prototype for large-scale ultraviolet laser systems for short wavelength ICF research. The system employs optical angular multiplexing and serial amplification by electron-beam-driven KrF laser amplifiers. The 1 to 5 ns pulse of the Aurora front end is split into 96 beams which are angularly and temporally multiplexed to produce a 480 ns pulse train for amplification by four KrF laser amplifiers. In the present system configuration half (48) of the amplified pulses are demultiplexed using different optical path lengths and delivered simultaneously to target. This paper discusses how the Aurora laser system has entered the initial operational phase by delivering pulse energies of greater than one kilojoule to target

  8. Recent progress in the Los Alamos KrF Program

    International Nuclear Information System (INIS)

    McDonald, T.E.; Cartwright, D.C.; Coggeshall, S.V.

    1988-01-01

    The goal of the Inertial Confinement Fusion Program (ICF) is to develop the ability to ignite and burn small masses of thermonuclear fuel. Although the present near-term objectives of the program are directed toward defense applications, ICF research continues to be carried out with a view to the longer term goal of commercial power production. The characteristics of a KrF laser make it an attractive candidate as an ICF driver. The KrF wavelength of 248 nm provides a target coupling that is very high at intensities of 10 14 w/cm 2 . In addition, the KrF laser can be repetitively operated at frequencies appropriate for a power reactor and has an intrinsically high efficiency, which allows projections to the long-term goal of energy production. The ICF program at Los Alamos consists of driver development, target design and fabrication, and target experimentation. The major effort at present is the investigation and development of KrF technology to determine its applicability for use in a laboratory driver at Los Alamos. Such a driver would be used in defense related technology studies and in areas of scientific study such as highly ionized materials and high-energy-density physics

  9. Laser Plasma Instability Experiments with KrF Lasers

    National Research Council Canada - National Science Library

    Weaver, J. L; Oh, J; Afeyan, B; Phillips, L; Seely, J; Feldman, U; Brown, C; Karasik, , M; Serlin, V; Aglitskiy, Y; Mostovych, A. N

    2007-01-01

    ...) with a rep-rate system that has a per pulse laser energy well below 1 megajoule. Measurements of LPI using the Nike KrF laser are presented at and above intensities needed for the FTF (Ĩ2x1015 W/cm2...

  10. Electromagnetic transition strengths in 75Kr and 79Sr

    International Nuclear Information System (INIS)

    Cardona, M.A.; Filevich, Alberto; Garcia Bermudez, Gerardo; Achterberg, Erhard

    1989-01-01

    Experimental and theoretical studies of nuclear structure in light Kr and Sr isotopes have revealed a region of large quadrupole deformation. In this work, deformation properties of odd-nuclei 75 Kr and 79 Sr have been investigated. For this purpose, lifetime of excited states in both nuclei have been measured by means of the recoil distance Doppler shift technique. These nuclei were populated via the reactions: 54 Fe( 24 Mg,2pn) 75 Kr at 75 MeV and 54 Fe( 28 Si,2pn) 79 Sr at 97 MeV, the beams were provided by the Tandar accelerator. The experimental B(E2) values for these nuclei were well reproduced in the framework of the triaxial-rotor-plus quasiparticle model. In order to fix the parameters of the model a study of neighboring even-even Kr isotopes was performed. The whole N=3 and N=4 oscillator shell was used for the space configuration of the odd particle for negative and positive bands respectively. (Author) [es

  11. Difference flow and electrical conductivity measurements at the Olkiluoto site in Eurajoki, drillholes OL-KR54, OL-KR55, OL-KR55B and OL-KR47B

    Energy Technology Data Exchange (ETDEWEB)

    Komulainen, J.; Poellaenen, J.; Hurmerinta, E.; Ripatti, K. [Poeyry Finland Oy, Espoo (Finland)

    2012-04-15

    The Posiva Flow Log, Difference flow method (PFL DIFF) uses a flowmeter that incorporates a flow guide and can be used for relatively quick determinations of hydraulic conductivity and hydraulic head of fractures/fractured zones in drillholes. This report presents the principles of the method and the results of measurements carried out in drillholes OL-KR54, OL-KR55, OL-KR55B and OL-KR47B at the Olkiluoto investigation site between January 2011 and September 2011. The measuring programme employed was the same in all drillholes. The applied section lengths of the flow guide were either 2 m and 0.5 m. Flow into the drillhole or from the drillhole to the bedrock was measured within the section length. The measurements were carried out in both pumped and natural (i.e. un-pumped) conditions. The transmissivity and hydraulic head of zones were calculated from the flow and pressure results. The device used includes a sensor for single point resistance (SPR). SPR was measured in connection with the flow measurements. The electrical conductivity (EC) of fracture-specific water was measured in chosen fractures. Fractures were selected on the basis of the measured flow from fractures into the drillhole. The drillhole flow (flow along the drillhole) was measured in conjunction with drillhole EC measurements. (orig.)

  12. Radiative and nonradiative lifetimes in excited states of Ar, Kr and Xe atoms in Ne matrix

    International Nuclear Information System (INIS)

    Hahn, U.; Schwentner, N.

    1979-10-01

    Synchrotron radiation with its intense continuum and its excellent time structure has been exploited for time resolved luminescence spectroscopy in the solid state. By selective excitation of n = 1, n' = 1 and n = 2 exciton states of Xe, Kr and Ar atoms in Ne matrix we were able to identify the emitting states involved. Lifetimes within the cascade of radiative and radiationless relaxation between excited states as well as the radiative lifetimes for transitions to the ground state have been derived from the decay curves. Energy positions and radiative lifetimes of the emitting states correspond quite well with those of the free atoms. Radiative and radiationless relaxation processes take place within the manifold of excited states of the guest atoms. The rate constants for radiationless decay confirm an energy gap law. The order of the radiationless processes reaches in some cases extremely high values. Selection rules for spin and angular momentum are essential to understand the observed radiationless transition rates. (orig.)

  13. Arsenic precipitation from metallurgical effluents

    International Nuclear Information System (INIS)

    Navarro, P.; Vargas, C.; Araya, E.; Martin, I.; Alguacil, F. J.

    2004-01-01

    In the mining-metallurgical companies different liquid effluents are produced, which can contain a series of dissolved elements that are considered dangerous from an environmental point of view. One of these elements is the arsenic, especially in the state of oxidation +5 that can be precipitated as calcium or iron arsenate. To fulfil the environmental requests it should have in solution a content of arsenic lower than 0,5 mg/l and the obtained solid product should be very stable under the condition in which it will be stored. this work looks for the best conditions of arsenic precipitation, until achieving contents in solution lower than such mentioned concentration. Also, the stability of the precipitates was studied. (Author) 7 refs

  14. Analysis of precipitation in a Cu-Cr-Zr alloy

    Institute of Scientific and Technical Information of China (English)

    Zhao Mei; Lin Guobiao; Wang Zidong; Zhang Maokui

    2008-01-01

    Precipites in Cu-0.42%Cr-0.21%Zr alloy were analyzed by using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDXS) and transmission electron microscope (TEM). After the solid solution was performed at 980℃ for 2 h, water-quenched and aged at 450℃ for 20 h, the precipite had a bimodal distribution of precipitate size. The coarse precipitates are pure Cr and Cu5Zr, the dispersed fine precipitate is CrCu2(Zr, Mg) and pure Cr ranging from 1 to 50 nm. The coarse phases formed during solidification and were left undissolved during solid solution. The fine precipitates are the hardening precipitates that form due to decomposition of the supersaturated solid solution during aging.

  15. Precipitation processes in implanted materials

    International Nuclear Information System (INIS)

    Borders, J.A.

    1978-01-01

    Ion implantation is a nonequilibrium process. It is possible to implant materials with impurities to concentration levels which exceed the solid solubilities. The return of the system to thermodynamic equilibrium is often accomplished by precipitation of the implanted species or a compound involving atoms of both the host and the implanted species. This may involve long time scales when taking place at room temperature or it may take place during the implantation

  16. Hydraulic conductivity measurements with HTU at Eurajoki, Olkiluoto, drillholes OL-KR28 and OL-KR39 in 2006

    International Nuclear Information System (INIS)

    Haemaelaeinen, H.

    2007-05-01

    As a part of the site investigations for the disposal of spent nuclear fuel, hydraulic conductivity measurements were carried out in drillholes OL-KR28 and OL-KR39 at Eurajoki, Olkiluoto. The objective was to investigate the distribution of the hydraulic conductivity in the surrounding bedrock volume. Measurements were carried out during summer 2006. The total length of the borehole OL-KR28 is 656,33 m, 352 m of which was covered by 176 standard tests with 2 m packer separation as specified in the measurement plan. Respectively, OL-KR39 is 502,97 m deep and 101 similar tests were made in it covering 202 m of the hole. The measured sections are around the depths of the planned repository. Double-packer constant-head method was used throughout with nominal 200 kPa overpressure. Injection stage lasted normally 20 minutes and fall-off stage 10 minutes. The tests were often shortened if there were clear indications that the hydraulic conductivity is below the measuring range of the system. The pressure in the test section was let to stabilise at least 5 min before injection. In some test sections the test stage times were extended. Two transient (Horner and 1/Q) interpretations and one stationary-state (Moye) interpretation were made in-situ immediately after the test. The Hydraulic Testing Unit (HTU-system) is owned by Posiva Oy and it was operated by Geopros Oy. (orig.)

  17. High-accuracy mass measurements of neutron-rich Kr isotopes

    CERN Document Server

    Delahaye, P; Blaum, K; Carrel, F; George, S; Herfurth, F; Herlert, A; Kellerbauer, A G; Kluge, H J; Lunney, D; Schweikhard, L; Yazidjian, C

    2006-01-01

    The atomic masses of the neutron-rich krypton isotopes 84,86-95Kr have been determined with the tandem Penning trap mass spectrometer ISOLTRAP with uncertainties ranging from 20 to 220 ppb. The masses of the short-lived isotopes 94Kr and 95Kr were measured for the first time. The masses of the radioactive nuclides 89Kr and 91Kr disagree by 4 and 6 standard deviations, respectively, from the present Atomic-Mass Evaluation database. The resulting modification of the mass surface with respect to the two-neutron separation energies as well as implications for mass models and stellar nucleosynthesis are discussed.

  18. The effect of simultaneous electron and Kr+ irradiation on amorphization of CuTi

    International Nuclear Information System (INIS)

    Koike, J.; Okamoto, P.R.; Rehn, L.E.; Meshii, M.

    1989-01-01

    CuTi was irradiated with 1-MeV electrons and Kr + ions simultaneously at temperatures from 10 to 423 K. Retardation of Kr + -induced amorphization was observed with simultaneous electron irradiation at 295 and 423 K. The retardation effect increased with increasing irradiation temperature and relative electron-to-Kr dose rate. In contrast, simultaneous irradiation below 100 K showed an additive effect of electron- and Kr + -induced amorphization. The results can be explained by the mobility point defects introduced by electron irradiation interacting with Kr + -induced displacement cascades. 6 refs., 6 figs

  19. Alternative methods for 85Kr ultimate storage

    International Nuclear Information System (INIS)

    Penzhorn, R.D.

    Storage by ion implantation is described. Ion implantation (II) involves the penetration and retention of ions accelerated in the keV-MeV energy range in the surface layer of a solid material. Through collisions, the accelerated ions that are to be implanted give off electrical energy to the target material and heat it up. The number of ions implanted, resulting from the entire ion current, depends not on the physical properties of the implantation material but rather is determined by the external system. The gas enclosed in the matrix is in the form of small bubbles. The size of the bubbles depends on the temperature and is in the range of a few hundred Angstrom units. The bubbles are stable at least up to the temperature at which they were produced. Therefore, bombardment of the metal at higher temperatures decreases the danger of the gas being released, even at very high temperatures. Methods of producing noble gas ions are discussed along with embedding capacity, safety, recovery, and advantages and disadvantages of the method

  20. Precipitation and Hardening in Magnesium Alloys

    Science.gov (United States)

    Nie, Jian-Feng

    2012-11-01

    Magnesium alloys have received an increasing interest in the past 12 years for potential applications in the automotive, aircraft, aerospace, and electronic industries. Many of these alloys are strong because of solid-state precipitates that are produced by an age-hardening process. Although some strength improvements of existing magnesium alloys have been made and some novel alloys with improved strength have been developed, the strength level that has been achieved so far is still substantially lower than that obtained in counterpart aluminum alloys. Further improvements in the alloy strength require a better understanding of the structure, morphology, orientation of precipitates, effects of precipitate morphology, and orientation on the strengthening and microstructural factors that are important in controlling the nucleation and growth of these precipitates. In this review, precipitation in most precipitation-hardenable magnesium alloys is reviewed, and its relationship with strengthening is examined. It is demonstrated that the precipitation phenomena in these alloys, especially in the very early stage of the precipitation process, are still far from being well understood, and many fundamental issues remain unsolved even after some extensive and concerted efforts made in the past 12 years. The challenges associated with precipitation hardening and age hardening are identified and discussed, and guidelines are outlined for the rational design and development of higher strength, and ultimately ultrahigh strength, magnesium alloys via precipitation hardening.

  1. En etisk diskussion af screening for kræftsygdomme

    Directory of Open Access Journals (Sweden)

    Peter Laurs Sørensen

    2009-05-01

    Full Text Available I 2007 gennemførte forbundskansler Angela Merkel en sundhedsreform der blandt andet indebærer, at tyske borgere ikke frit kan afgøre, om de vil deltage i forebyggende programmer, da et fravalg kan medføre økonomiske konsekvenser. Hermed udvider den tyske stat sin ret til at gribe ind i borgernes liv, når det handler om sekundær forebyggelse, fx i form af screening for kræftsygdomme. Dette kan være problematisk da den bedst tilgængelige evidens viser at tre igangværende kræftscreeningsprogrammer ikke kun har gavnlige virkninger, men også betydelige skadelige virkninger. Formålet med denne undersøgelse var at undersøge, hvilke holdninger eksperter, politikere og sundhedsmyndigheder i Danmark har til tvang og/eller belønning i forbindelse med screening for kræftsygdomme, og om de ville støtte eller fraråde en tysk model i det danske sundhedsvæsen.Der blev foretaget enkeltinterviews med strategisk udvalgte eksperter. Interviewene blev transskriberet og analyseret med en fænomenologisk analysemetode, og derefter analyseret og diskuteret i forhold til utilitaristisk og deontologisk etik, samt evidensen vedrørende de tre eksisterende kræftscreeningsprogrammer i Danmark.Alle informanterne var kritiske over for det tyske forslag. Til gengæld blev forholdet mellem de gavnlige og skadelige virkninger af kræftscreening vurderet meget forskelligt. Manglen på enighed, uklare udtalelser og ikke-stringent terminologi bestyrkede vor konklusion; at det danske sundhedsvæsen for det første ikke bør følge den tyske kurs og, for det andet, at man bør være kritisk over for implementering af screeningsprogrammer for kræftsygdomme. Hvis forebyggende initiativer kan være mere til skade end gavn, bør de altid overvejes nøje i lyset af sundhedsvæsnets oprindelige intention om at hjælpe og beskytte det enkelte menneske.http://dx.doi.org/10.5324/eip.v3i1.1712

  2. KrF lasers as inertial fusion drivers

    International Nuclear Information System (INIS)

    Harris, D.B.; Berggren, R.R.; Kurnit, N.A.; Lowenthal, D.D.; Berger, R.G.; Eggleston, J.M.; Ewing, J.J.; Kushner, M.J.

    1986-01-01

    A new type of KrF laser system has been proposed that has a significantly higher efficiency than pure angular multiplexed KrF lasers. This system uses electron-beam-sustained discharge lasers to pump a high gain Raman amplifier. The discharge lasers can operate at a higher efficiency than e-beam pumped lasers, and the forward Raman scattering process has both a high gain and high quantum efficiency using the rotational transition. The Raman system cost and performance has been examined and compared to the pure angular multiplexed system. The discharge-Raman system has a higher efficiency (12% vs 9%) and a higher cost ($140/joule vs $100/joule). For an ICF power plant driver, the higher efficiency offsets the higher cost, making the discharge-Raman system appear to be an attractive alternative to the pure angular multiplexed system

  3. KrF lasers as inertial fusion drivers

    International Nuclear Information System (INIS)

    Harris, D.B.; Berggren, R.R.; Kurnit, N.A.; Lowenthal, D.D.; Berger, R.G.; Eggleston, J.M.; Ewing, J.J.; Kushner, M.J.

    1985-01-01

    A new type of KrF laser system has been proposed that has a significantly higher efficiency than pure angular multiplexed KrF lasers. This system uses electron-beam-sustained discharge lasers to pump a high gain Raman amplifier. The discharge lasers can operate at a higher efficiency than e-beam pumped lasers, and the forward Raman scattering process has both a high gain and high quantum efficiency using the rotational transition. The Raman system cost and performance has been examined and compared to the pure angular multiplexed system. The discharge-Raman system has a higher efficiency (12.3% vs 9.1%) and a higher cost ($140/joule vs $100/joule). For an ICF power plant driver, the higher efficiency offsets the higher cost, making the discharge-Raman system appear to be an attractive alternative to the pure angular multiplexed system

  4. Separation of Kr-Xe system by thermal diffusion method

    International Nuclear Information System (INIS)

    Yoshida, Hiroshi; Numata, Kazuyoshi; Matsuda, Yuji; Ouchi, Misao; Naruse, Yuji

    1979-11-01

    Separation experiments of Kr-Xe system were carried out to study the possibility of adapting thermal diffusion method for concentration of krypton in a fuel reprocessing off-gas treatment process. The results are as follows. (1) A batchwise thermal diffusion column of hot tube diameter 21 mm, cold tube diameter 32 mm, effective hight 1000 mm and volume -- 500 CC is the best in separation characteristics and in ease of operation under the different conditions. (2) The overall separation factor increases with increase of the operating temperature in the column with and without reservoir. (3) The optimum operating pressure (about 400 Torr) is independent of the operating conditions such as temperature, reservoir volume and feed gas content. (4) A preliminary design of the Kr-Xe separating plant for a reprocessing plant (1500 ton-U/yr) shows the required number of columns and the total electric power. (author)

  5. Single electron capture in N^+ -(Ne, Kr, Xe) collisions

    Science.gov (United States)

    Reyes, Pedro G.; Castillo, Fermin; Martinez, Horacio

    2001-05-01

    Total cross sections for single electron capture of N^+ ions impinging on Ne, Kr and Xe were measured in the energy range of 1.5 to 5.0 keV. The electron capture cross sections for all the targets studied are found to be in excellent agreement with previous data in the low-energy range. The present data together with previous measurements give a general shape of the whole curve of single electron capture cross sections for the N^+ - Ne system. For the cases of N^+ - (Kr, Xe) systems, semiempirical calculation using the two-state approximation are in very good agreement with present cross sections data. Research supported by DGAPA IN-100392 and CONACyT 32175-E

  6. The β+-electron capture decay of 73Kr

    International Nuclear Information System (INIS)

    Miehe, C.; Dessagne, P.; Pujol, Ch.; Walter, G.; Jonson, B.; Lindroos, M.

    1999-01-01

    The β + - electron capture decay of 73 Kr, produced at the ISOLDE CERN facility, has been studied by β-delayed proton and gamma emission. The established decay scheme involves 15 up to now unreported gamma emitting levels in 73 Br. The total proton branching ratio has been measured to be 0.0025±0.0003. From this work, a spin and parity 3/2 - is assigned to the 73 Kr ground state, on the basis of the allowed β branch to the 73 Br J π =1/2 - ground state and the feeding of the 5/2 + level located at 286 keV in 73 Br. (orig.)

  7. Applications developed for byproduct 85Kr and tritium

    International Nuclear Information System (INIS)

    Remini, W.C.; Case, F.N.; Haff, K.W.; Tiegs, S.M.

    1983-01-01

    The radionuclides, krypton-85 and tritium, both of which are gases under ordinary conditions, are used in many applications in industries and by the military forces. Krypton-85 is produced during the fissioning of uranium and is released during the dissolution of spent-fuel elements. It is a chemically inert gas that emits 0.695-MeV beta rays and a small yield of 0.54-MeV gammas over a half life of 10.3 years. Much of the 85 Kr currently produced is released to the atmosphere; however, large-scale reprocessing of fuel will require collection of the gas and storage as a waste product. An alternative to storage is utilization, and since the chemical and radiation characteristics of 85 Kr make this radionuclide a relatively low hazard from the standpoint of contamination and biological significance, a number of uses have been developed. Tritium is produced as a byproduct of the nuclear-weapons program, and it has a half life of 12.33 years. It has a 0.01861-MeV beta emission and no gamma emission. The absence of a gamma-ray energy eliminates the need for external shielding of the devices utilizing tritium, thus making them easily transportable. Many of the applications require only small quantities of 85 Kr or tritium; however, these uses are important to the technology base of the nation. A significant development that has the potential for beneficial utilization of large quantities of 85 Kr and of tritium involves their use in the production of low-level lighting devices. Since these lights are free from external fuel supplies, have a long half life (> 10 years), are maintenance-free, reliable, and easily deployed, both military and civilian airfield-lighting applications are being studied

  8. Shape coexistence in 72Kr at finite angular momentum

    International Nuclear Information System (INIS)

    Almehed, Daniel; Walet, Niels R.

    2004-01-01

    We investigate shape coexistence in a rotating nucleus. We concentrate on the case of 72 Kr which exhibits an interesting interplay between prolate and oblate shaped states as a function of angular momentum. The calculation uses the local harmonic version of the method of self-consistent adiabatic large-amplitude collective motion. We analyse how the collective behaviour of the system changes with angular momentum and we focus on the role of non-axial shapes

  9. Shape determination in Coulomb excitation of $^{72}$Kr

    CERN Multimedia

    Reiter, P; Kruecken, R; Paul, E S; Wadsworth, R; Heenen, P

    Nuclei with oblate shapes at low spins are very special in nature because of their rarity. Both theoretical and experimental shape co-existence studies in the mass 70 region for near proton drip-line nuclei suggest $^{72}$Kr to be the unique case with oblate low-lying and prolate high-lying levels. However, there is no direct experimental evidence in the literature to date for the oblate nature predicted for the first 2$^+$ state in $^{72}$Kr. We propose to determine the sign of the spectroscopic quadrupole moment of this state via the re-orientation effect in a low-energy Coulomb excitation measurement. In the inelastic excitation of the 2$^+$ state in $^{72}$Kr beam of 3.1 MeV/u with an intensity of 800 pps at REX-ISOLDE impinging on $^{104}$Pd target, the re-orientation effect plays a significant role. The cross section measurement for the 2$^+$ state should thus allow the model-independent determination of the sign of the quadrupole moment unambiguously and will shed light on the co-existing prolate and o...

  10. Kr ion irradiation study of the depleted-uranium alloys

    Science.gov (United States)

    Gan, J.; Keiser, D. D.; Miller, B. D.; Kirk, M. A.; Rest, J.; Allen, T. R.; Wachs, D. M.

    2010-12-01

    Fuel development for the reduced enrichment research and test reactor (RERTR) program is tasked with the development of new low enrichment uranium nuclear fuels that can be employed to replace existing high enrichment uranium fuels currently used in some research reactors throughout the world. For dispersion type fuels, radiation stability of the fuel-cladding interaction product has a strong impact on fuel performance. Three depleted-uranium alloys are cast for the radiation stability studies of the fuel-cladding interaction product using Kr ion irradiation to investigate radiation damage from fission products. SEM analysis indicates the presence of the phases of interest: U(Al, Si) 3, (U, Mo)(Al, Si) 3, UMo 2Al 20, U 6Mo 4Al 43 and UAl 4. Irradiations of TEM disc samples were conducted with 500 keV Kr ions at 200 °C to ion doses up to 2.5 × 10 19 ions/m 2 (˜10 dpa) with an Kr ion flux of 10 16 ions/m 2/s (˜4.0 × 10 -3 dpa/s). Microstructural evolution of the phases relevant to fuel-cladding interaction products was investigated using transmission electron microscopy.

  11. Kr ion irradiation study of the depleted-uranium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Gan, J., E-mail: Jian.Gan@inl.go [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-6188 (United States); Keiser, D.D. [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-6188 (United States); Miller, B.D. [University of Wisconsin, 1500 Engineering Drive, Madison, WI 53706 (United States); Kirk, M.A.; Rest, J. [Argonne National Laboratory, 9700 South Cass Ave., Argonne, IL 60439 (United States); Allen, T.R. [University of Wisconsin, 1500 Engineering Drive, Madison, WI 53706 (United States); Wachs, D.M. [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-6188 (United States)

    2010-12-01

    Fuel development for the reduced enrichment research and test reactor (RERTR) program is tasked with the development of new low enrichment uranium nuclear fuels that can be employed to replace existing high enrichment uranium fuels currently used in some research reactors throughout the world. For dispersion type fuels, radiation stability of the fuel-cladding interaction product has a strong impact on fuel performance. Three depleted-uranium alloys are cast for the radiation stability studies of the fuel-cladding interaction product using Kr ion irradiation to investigate radiation damage from fission products. SEM analysis indicates the presence of the phases of interest: U(Al, Si){sub 3}, (U, Mo)(Al, Si){sub 3}, UMo{sub 2}Al{sub 20}, U{sub 6}Mo{sub 4}Al{sub 43} and UAl{sub 4}. Irradiations of TEM disc samples were conducted with 500 keV Kr ions at 200 {sup o}C to ion doses up to 2.5 x 10{sup 19} ions/m{sup 2} ({approx}10 dpa) with an Kr ion flux of 10{sup 16} ions/m{sup 2}/s ({approx}4.0 x 10{sup -3} dpa/s). Microstructural evolution of the phases relevant to fuel-cladding interaction products was investigated using transmission electron microscopy.

  12. Laser plasma instability experiments with KrF lasers

    International Nuclear Information System (INIS)

    Weaver, J. L.; Karasik, M.; Serlin, V.; Obenschain, S.; Chan, L-Y.; Kehne, D.; Schmitt, A. J.; Colombant, D.; Velikovich, A.; Oh, J.; Lehmberg, R. H.; Afeyan, B.; Phillips, L.; Seely, J.; Brown, C.; Feldman, U.; Aglitskiy, Y.; Mostovych, A. N.; Holland, G.

    2007-01-01

    Deleterious effects of laser-plasma instability (LPI) may limit the maximum laser irradiation that can be used for inertial confinement fusion. The short wavelength (248 nm), large bandwidth, and very uniform illumination available with krypton-fluoride (KrF) lasers should increase the maximum usable intensity by suppressing LPI. The concomitant increase in ablation pressure would allow implosion of low-aspect-ratio pellets to ignition with substantial gain (>20) at much reduced laser energy. The proposed KrF-laser-based Fusion Test Facility (FTF) would exploit this strategy to achieve significant fusion power (150 MW) with a rep-rate system that has a per pulse laser energy well below 1 MJ. Measurements of LPI using the Nike KrF laser are presented at and above intensities needed for the FTF (I∼2x10 15 W/cm 2 ). The results to date indicate that LPI is indeed suppressed. With overlapped beam intensity above the planar, single beam intensity threshold for the two-plasmon decay instability, no evidence of instability was observed via measurements of (3/2)ω o and (1/2)ω o harmonic emissions

  13. Puzzling Two-Proton Decay of 67Kr

    Science.gov (United States)

    Wang, S. M.; Nazarewicz, W.

    2018-05-01

    Ground-state two-proton (2 p ) radioactivity is a rare decay mode found in a few very proton-rich isotopes. The 2 p decay lifetime and properties of emitted protons carry invaluable information on nuclear structure in the presence of a low-lying proton continuum. The recently measured 2 p decay of 67Kr turned out to be unexpectedly fast. Since 67Kr is expected to be a deformed system, we investigate the impact of deformation effects on the 2 p radioactivity. We apply the recently developed Gamow coupled-channel framework, which allows for a precise description of three-body systems in the presence of rotational and vibrational couplings. This is the first application of a three-body approach to a two-nucleon decay from a deformed nucleus. We show that deformation couplings significantly increase the 2 p decay width of 67Kr; this finding explains the puzzling experimental data. The calculated angular proton-proton correlations reflect a competition between 1 p and 2 p decay modes in this nucleus.

  14. On the structure of collective bands in 78Kr

    International Nuclear Information System (INIS)

    Hellmeister, H.P.

    1980-01-01

    Using 16 O, 19 F, and 12 C induced reactions high spin states in 78 Kr were excited. The targets consisted of 65 Cu, 69 Ni, and 68 Zn. On the base of gamma spectroscopic methods as γγ-coincidences, angular distributions and excitation functions a level scheme of 78 Kr is proposed. Four bands could be identified, which decay mostly by stretched E2-transitions. From recoil distance Doppler shift as well as Doppler shift attenuation measurements lifetimes of about 20 states were measured. The β-decay of the 103 keV isomeric state and the ground state in 78 Rb was observed and the half-lifes determined. Altogether a very good agreement of the level scheme and the E2- and E1-transition strength with predictions of the interacting boson model were found. Using a Monte Carlo code the γ-decay of the continuum of highly excited nuclei is described. Entry states, mean γ-energies, γ-spectra, mean multiplicities, multipolarities, and mean feeding times as well as e.g. their second moments were calculated for the reactions 58 Ni( 16 O,2p) 72 Se and 68 Zn( 12 C,2n) 78 Kr. The results are discussed and compared with experimental data. (HSI) [de

  15. Radiative lifetimes and two-body collisional deactivation rate constants in argon for Kr(4p 55p) and Kr(4p 55p') states

    International Nuclear Information System (INIS)

    Chang, R.S.F.; Horiguchi, H.; Setser, D.W.

    1980-01-01

    The radiative lifetimes and collisional deactivation rate constants, in argon, of eight Kr(4p 5 [ 2 P/sub 1/2/]5p and [ 2 P/sub 3/2/]5p) levels have been measured by a time-resolved laser-induced fluorescence technique in a flowing afterglow apparatus. The measured radiative lifetimes are compared with other experimental values and with theoretical calculations. Radiative branching ratios of these excited states also were measured in order to assign the absolute transition probabilities of the Kr(5p,5p'--5s, 5s') transition array from the radiative lifetimes. In addition to the total deactivation rate constants, product states from two-body collisions between Kr(5p and 5p') atoms and ground state argon atoms were identified from the laser-induced emission spectra, and product formation rate constants were assigned. Two-body intermultiplet transfer from Kr(4p 5 [ 2 P/sub 1/2/]5p) to the Kr(4p 5 [ 2 P/sub 3/2/]4d) levels occurs with ease. Intermultiplet transfer from the lowest level in the (4p 5 5p) configuration to the Kr(4p 5 5s and 5s') manifold was fast despite the large energy defect. However, this was the only Kr(5p) level that gave appreciable transfer to the Kr(5s or 5s') manifold. Generally the favored product states are within a few kT of the entrance channel

  16. Characterization of Carbamazepine-Loaded Solid Lipid ...

    African Journals Online (AJOL)

    loaded solid lipid nanoparticles by RESS as well as their characterization has been achieved in this study. Keywords: Rapid expansion of supercritical fluid, Stearic acid, Solid lipid nanoparticles, Carbamazepine, Co-precipitation ...

  17. Low energy γ- γ and e{sup −}- γ PAC measurements using APDs and the probe nuclei {sup 83}Rb({sup 83}Kr) and {sup 83m}Kr({sup 83}Kr)

    Energy Technology Data Exchange (ETDEWEB)

    Arenz, M., E-mail: arenz@hiskp.uni-bonn.de; Vianden, R., E-mail: vianden@hiskp.uni-bonn.de [Universität Bonn, Helmholtz-Institut für Strahlen- und Kernphysik (Germany)

    2016-12-15

    In the field of Perturbed Angular Correlation (PAC) measurements Avalanche Photo Diodes (APD) are rarely used, despite their favourable properties for fast counting purposes at low energies. This work demonstrates their application in combination with a simple and cheap custom build voltage sensitive preamplifier module. Using the PAC nuclei {sup 83}Rb({sup 83}Kr) and {sup 83m}Kr({sup 83}Kr), the time resolution of the set-up is analysed and the feasibility of precise timing measurements is shown.

  18. Cascade processes after 3p-shell threshold photoionization of Kr

    International Nuclear Information System (INIS)

    Matsui, T.; Yoshii, H.; Higurashi, A.; Hayaishi, T.; Murakami, E.; Aoto, T.; Onuma, T.; Morioka, Y.; Yagishita, A.

    2002-01-01

    Yield spectra of the multiply charged ions Kr 2+ , Kr 3+ , Kr 4+ and Kr 5+ in coincidence with threshold electrons (E k ≤0.03 eV) have been measured near the 3p-shell ionization region of Kr. Profiles of post-collision interaction (PCI) effects induced by Auger cascades following 3p-shell threshold ionization are derived from these coincidence spectra. On the basis of the PCI profiles, the number of Auger cascade steps for each of the decay channels leading to the formation of the multiply charged ions in 3p 3/2 - and 3p 1/2 -shell threshold ionization of Kr was determined, and the branching ratios of the decay channels were estimated. (author)

  19. Cosmiclike domain walls in superfluid 3He-B: Instantons and diabolical points in (k,r) space

    International Nuclear Information System (INIS)

    Salomaa, M.M.; Volovik, G.E.

    1988-01-01

    The possible planar superfluid B-B boundaries between inequivalent B-phase vacua are considered; such B-B interfaces provide an analogy with the cosmic domain walls that are believed to have precipitated in the phase transitions of the early Universe. Several of them display nontrivial structure in (k,r) space (i.e., the union of the momentum and real spaces). Such a wall represents an instanton connecting two B-phase vacua with different k-space topology. The transition between the vacua occurs through the formation of a pointlike defect either in the (k,r) space, or in the (k,t) space. These defects are so-called diabolical points of codimension 4, at which the fermionic energy tends to zero, thus providing the fermionic zero modes. Such points are new examples (within condensed-matter physics) of the peculiar diabolical points, which are characterized by the occurrence of a contact between the different branches of the quasiparticle spectra; in the present case, the branches of particles and holes, respectively. These points are here discussed for the case of the superfluid phases of liquid 3 He in close analogy with the quantum field theory of fermions interacting with classical bosonic fields. The cosmiclike domain walls in superfluid 3 He-B are observable in principle; in particular, the motion of the superfluid A-B interface is governed at low temperatures by the periodical emission of these topological excitation planes

  20. Kartulisortide pikaaegne säilitamine krüomeetodil / Jaanika Edesi, Viive Rosenberg

    Index Scriptorium Estoniae

    Edesi, Jaanika

    2014-01-01

    Taimmaterjali krüosäilitus on hetkel uusim ja perspektiivikaim säilitusmeetod. Krüosäilituse all mõistetakse bioloogilise materjali säilitamist väga madalal temperatuuril elu- ja taastumisvõimelisena. Krüosäilitus toimub tavaliselt vedelas lämmastikus (-196 °C) või selle gaasilises faasis alla -150 °C kraadi.

  1. Alternative processes for the long-term storage of Kr-85

    International Nuclear Information System (INIS)

    Penzhorn, R.D.

    1977-12-01

    The forseeable problems which are characteristic of the long-term storage of Kr-85, are discussed on the basis of the chemical, physical and radiological properties of the fission noble gases krypton and xenon as well as rubidium, the daughter nuclide of Kr-85. The various alternatives suggested in the literature for the long-term storage of Kr-85 are reviewed. The technological realization of each of the proposed alternatives is analyzed. (orig.) [de

  2. Xe/Kr Selectivity Measurements using AgZ-PAN at Various Temperatures

    International Nuclear Information System (INIS)

    Garn, Troy Gerry; Greenhalgh, Mitchell Randy; Watson, Tony Leroy

    2015-01-01

    In preparation for planned FY-15 Xe/Kr multi-column testing, a series of experiments were performed to determine the selectivity of Xe over Kr using the silver converted mordenite-polyacrylonitrile (AgZ-PAN) sorbent. Results from these experiments will be used for parameter selection guidelines to define test conditions for Kr gas capture purity evaluations later this year. The currently configured experimental test bed was modified by installing a new cooling apparatus to permit future multi-column testing with independent column temperature control. The modified test bed will allow for multi-column testing to facilitate a Xe separation followed by a Kr separation using engineered form sorbents. Selectivity experiments were run at temperatures of 295, 250 and 220 K. Two feed gas compositions of 1000 ppmv Xe, 150 ppmv Kr in either a He or an air balance were used. AgZ-PAN sorbent selectivity was calculated using Xe and Kr capacity determinations. AgZ-PAN sorbent selectivities for Xe over Kr of 72 were calculated at room temperature (295 K) using the feed gas with a He balance and 34 using the feed gas with an air balance. As the test temperatures were decreased the selectivity of Xe over Kr also decreased due to an increase in both Xe and Kr capacities. At 220 K, the sorbent selectivities for Xe over Kr were 22 using the feed gas with a He balance and 28 using the feed gas with an air balance. The selectivity results indicate that AgZ-PAN used in the first column of a multi-column configuration will provide adequate partitioning of Xe from Kr in the tested temperature range to produce a more pure Kr end product for collection.

  3. Modelled Precipitation Over Greenland

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes the annual total precipitation from 1985 to 1999 and monthly total precipitation from January 1985 to December 1999. The data is derived from...

  4. Mass measurement on the rp-process waiting point {sup 72}Kr

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, D. [Gesellschaft fuer Schwerionenforschung mbH, Darmstadt (Germany); Kolhinen, V.S. [Jyvaeskylae Univ. (Finland); Audi, G. [CSNSM-IN2P3-Centre National de la Recherche Scientifique (CNRS), 91 - Orsay (FR)] [and others

    2004-06-01

    The mass of one of the three major waiting points in the astrophysical rp-process {sup 72}Kr was measured for the first time with the Penning trap mass spectrometer ISOLTRAP. The measurement yielded a relative mass uncertainty of {delta}m/m=1.2 x 10{sup -7} ({delta}m=8 keV). Other Kr isotopes, also needed for astrophysical calculations, were measured with more than one order of magnitude improved accuracy. We use the ISOLTRAP masses of{sup 72-74}Kr to reanalyze the role of the {sup 72}Kr waiting point in the rp-process during X-ray bursts. (orig.)

  5. Orestes Kinetics Model for the Electra KrF Laser

    Science.gov (United States)

    Giuliani, J. L.; Kepple, P.; Lehmberg, R. H.; Myers, M. C.; Sethian, J. D.; Petrov, G.; Wolford, M.; Hegeler, F.

    2003-10-01

    Orestes is a first principles simulation code for the electron deposition, plasma chemistry, laser transport, and amplified spontaneous emission (ASE) in an e-beam pumped KrF laser. Orestes has been benchmarked against results from Nike at NRL and the Keio laser facility. The modeling tasks are to support ongoing oscillator experiments on the Electra laser ( 500 J), to predict performance of Electra as an amplifier, and to develop scaling relations for larger systems such as envisioned for an inertial fusion energy power plant. In Orestes the energy deposition of the primary beam electrons is assumed to be spatially uniform, but the excitation and ionization of the Ar/Kr/F2 target gas by the secondary electrons is determined from the energy distribution function as calculated by a Boltzmann code. The subsequent plasma kinetics of 23 species subject to over 100 reactions is followed with 1-D spatial resolution along the lasing axis. In addition, the vibrational relaxation among excited electronic states of the KrF molecule are included in the kinetics since lasing at 248 nm can occur from several vibrational lines of the B state. Transport of the lasing photons is solved by the method of characteristics. The time dependent ASE is calculated in 3-D using a ``local look-back'' scheme with discrete ordinates and includes specular reflection off the side walls and rear mirror. Gain narrowing is treated by multi-frequency transport of the ASE. Calculations for the gain, saturation intensity, extraction efficiency, and laser output from the Orestes model will be presented and compared with available data from Electra operated as an oscillator. Potential implications for the difference in optimal F2 concentration will be discussed along with the effects of window transmissivity at 248 nm.

  6. A new site for 85Kr measurements on groundwater samples

    International Nuclear Information System (INIS)

    Lange, T.; Hebert, D.

    2000-01-01

    Analysis of stable and radioactive isotopes is essential as a complement to geochemistry and geohydraulic investigations on groundwater regimes and their genesis. This is widely acknowledged also for the determination of the specific activity of 85 Kr in groundwater. The geochemical inertness and well-defined input function of 85 Kr allow estimates of groundwater age and enhance characterization of groundwater flow and components in many aquifer systems. A new site for measurement of the 85 Kr specific activity has been established at the Institute of Applied Physics at the Freiberg University, Saxony. Under normal conditions ca. 80 μl krypton are dissolved in 1 m 3 of water in contact with air. Therefore gas extraction has to be most effectively. A modified CO 2 extractor of 45 cm x 10 cm was chosen. The water is continuously pumped under pressure (3 - 4 bar) passing a Venturi-type nozzle, which simultaneously operates as a water-jet pump. The extracted gas flows through a CO 2 trap (NaOH 10 %), a H 2 O cold trap, through molecular sieves (5, 3 A) and a charcoal column, cooled by liquid nitrogen, where krypton, nitrogene and other components are adsorbed. Remaining gases re-enter the extractor at the Venturi-type nozzle. A small membrane pump supports the circulation. Due to the special design of the water outlet, contamination of the sample is avoided. Optional a compact stove heats the water to improve the extraction efficiency. If pressure supply is high enough, additional extractors can be run simultaneously. In a test run the recovery for radon was around 65 to 70 %. Further preparation steps of the raw krypton sample is performed in the laboratory. To obtain a good first enrichment a tube furnace filled with chrome powder is used to separate nitrogen and oxygen from the sample at 900 deg C. The following enrichment steps are performed by a preparation setup developed at GSF-Institute for Hydrology, Neuherberg. (author)

  7. Recent Developments on Discontinuous Precipitation

    Directory of Open Access Journals (Sweden)

    Zięba P.

    2017-06-01

    Full Text Available The discontinuous precipitation (DP belongs to a group of diffusive solid state phase transformations during which the formation of a new phase is heterogeneous and limited to a migrating reaction front (RF. The use of analytical electron microscopy provided reliable information that there is no differences in the diffusion rate at the stationary grain boundary and moving RF of DP reaction. On the other hand, the use of “in situ” transmission electron microscopy observations indicated the importance of stop-go motion or oscillatory movement of the RF.

  8. 85Kr and 39Ar background in GENIUS

    International Nuclear Information System (INIS)

    Klapdor Kleingrothaus, H.V.; Tomei, C.

    2003-01-01

    GENIUS is a proposal for a large-scale detector of rare events like double beta decay, cold dark matter and low-energy solar neutrinos in real time. The idea of GENIUS is to operate a large amount of 'naked' Ge detectors in liquid nitrogen, with the aim of reducing the background down to a level of 10 -3 counts/kg keV yr. In this work, we investigate the contribution to the background of GENIUS coming from argon ( 39 Ar) and krypton ( 85 Kr) contamination in the liquid nitrogen

  9. Core drilling of boreholes ONK-KR1, ONK-KR2, ONK-KR3, ONK-KR4 and ONK-PVA1 in ONKALO at Olkiluoto 2005

    Energy Technology Data Exchange (ETDEWEB)

    Rautio, T. [Suomen Malmi Oy, Espoo (Finland)

    2005-11-15

    Posiva Oy submitted am application for the Decision in Principle (the final disposal facility for spent nuclear fuel at Olkiluoto, Eurajoki) to the Finnish Government in May 1999. A positive decision was made at the end of 2000 by the Government The Finnish Parliament ratified the Decision in Principle in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. The investigation programme on the influence of grouting in ground-water chemistry will be started by Posiva. The programme consists of long-term and short-term effects of grouting and the influence of grouting at different distances from the tunnel on groundwater conditions. As a part of this Suomen Malmi oy (Smoy) core drilled four boreholes in ONKALO. The identification numbers of thee boreholes are ONK-KR1, ONK-KR2, ONK-KR3 and ONK-KR4. An additional borehole ONK-PVA1 was core drilled for long-term monitoring purposes in a place where no grouting is planned to be done.The diameter of the borehole sis 75.7 mm A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. The volume of the drilling water and the returning water were recorded as well as the pressure of the drilling water. The objective of these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The volume of the used drilling water was about 16 m{sup 3} and the measured volume of the returning water was about 11 dm{sup 3} in boreholes. The deviation of the boreholes was measured with the deviation measuring instrument EMS. The main rock types are migmatitic mica gneiss and granite. Filled fractures are most common type of fractures. The average fracture frequency of the boreholes varies from 0.6 to 3.1 pcs/m. The average RQD

  10. Core drilling of boreholes ONK-KR1, ONK-KR2, ONK-KR3, ONK-KR4 and ONK-PVA1 in ONKALO at Olkiluoto 2005

    International Nuclear Information System (INIS)

    Rautio, T.

    2005-11-01

    Posiva Oy submitted am application for the Decision in Principle (the final disposal facility for spent nuclear fuel at Olkiluoto, Eurajoki) to the Finnish Government in May 1999. A positive decision was made at the end of 2000 by the Government The Finnish Parliament ratified the Decision in Principle in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. The investigation programme on the influence of grouting in ground-water chemistry will be started by Posiva. The programme consists of long-term and short-term effects of grouting and the influence of grouting at different distances from the tunnel on groundwater conditions. As a part of this Suomen Malmi oy (Smoy) core drilled four boreholes in ONKALO. The identification numbers of thee boreholes are ONK-KR1, ONK-KR2, ONK-KR3 and ONK-KR4. An additional borehole ONK-PVA1 was core drilled for long-term monitoring purposes in a place where no grouting is planned to be done.The diameter of the borehole sis 75.7 mm A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. The volume of the drilling water and the returning water were recorded as well as the pressure of the drilling water. The objective of these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The volume of the used drilling water was about 16 m 3 and the measured volume of the returning water was about 11 dm 3 in boreholes. The deviation of the boreholes was measured with the deviation measuring instrument EMS. The main rock types are migmatitic mica gneiss and granite. Filled fractures are most common type of fractures. The average fracture frequency of the boreholes varies from 0.6 to 3.1 pcs/m. The average RQD value of

  11. Characterization and Modeling of Materials for Kr-Xe Separations

    Energy Technology Data Exchange (ETDEWEB)

    Forster, Paul [Univ. of Nevada, Las Vegas, NV (United States); Naduvalath, Balakrishnan [Univ. of Nevada, Las Vegas, NV (United States); Czerwinski, Ken [Univ. of Nevada, Las Vegas, NV (United States)

    2015-11-16

    We sought to identify practical adsorbents for the separation of Kr from Xe through pressure swing adsorption. We spent appreciable efforts on two categories of materials: metal-organic frameworks (MOFs) and zeolites. MOFs represent a new and exciting sorbent with numerous new framework topologies and surface chemistries. Zeolites are widely used and available commercial adsorbents. We have employed a combination of gas sorption analysis to analyze gas – surface interactions, computational modelling to both aid in interpreting experimental results and to predict practical adsorbents, and in-situ crystallographic studies to confirm specific experimental results.

  12. KrCl lasers for fusion. Final report

    International Nuclear Information System (INIS)

    1984-01-01

    The lasing characteristics of the Krypton Chloride excimer have been investigated in an e-beam laser facility. The results of experiments have been compared with the predictions of a comprehensive numerical kinetics model. The model predicts that the formation efficiency for KrCl* should be quite high (approx. = 20%) and these predictions appear to be borne out by experimental gain measurements. However, observed intrinsic laser efficiencies are poor, about 1 percent being the best observed in this program. We conclude that the poor lasing performance results from an adverse gain to loss ratio and an extreme sensitivity to optics losses because of the low characteristics magnitude of the gain

  13. Characterization and Modeling of Materials for Kr-Xe Separations

    International Nuclear Information System (INIS)

    Forster, Paul; Naduvalath, Balakrishnan; Czerwinski, Ken

    2015-01-01

    We sought to identify practical adsorbents for the separation of Kr from Xe through pressure swing adsorption. We spent appreciable efforts on two categories of materials: metal-organic frameworks (MOFs) and zeolites. MOFs represent a new and exciting sorbent with numerous new framework topologies and surface chemistries. Zeolites are widely used and available commercial adsorbents. We have employed a combination of gas sorption analysis to analyze gas - surface interactions, computational modelling to both aid in interpreting experimental results and to predict practical adsorbents, and in-situ crystallographic studies to confirm specific experimental results.

  14. Internal conversion in highly stripped 83Kr ions

    International Nuclear Information System (INIS)

    Copnell, J.; Phillips, W.R.; Barnett, A.R.; Rehm, K.E.; Ahmad, I.; Gehring, J.; Glagola, B.G.; Kutschera, W.

    1995-01-01

    The total decay probabilities per unit time of the first excited 9.4-keV state in 83 Kr have been measured in ions of ionicity q from 28 to 32. Using a γ-decay probability per unit time of 0.255(2)x10 6 s -1 gives internal conversion coefficients of 14.6(11), 14.9(10), 14.1(9), 14.6(11), and 15.2(24) for q=28--32, respectively. These values are compared with theoretical predictions

  15. Form coexistence in light krypton nuclei. Isomeric spectroscopy of 72,74Kr nuclei and Coulomb excitation of the 76Kr radioactive beam

    International Nuclear Information System (INIS)

    Bouchez, Emmanuelle

    2003-01-01

    The first part of this research thesis proposes an overview of the different theoretical calculations elaborated in the region of light krypton nuclei, and of published experimental results. The second part reports the electron and gamma isomeric spectroscopy of 72,74 Kr nuclei after fragmentation of the projectile by a magnetic separator (experimental installation, experimental results, discussion). The third part reports the study of the Coulomb excitation of the 76 Kr radioactive beam (method and experimental installation, data analysis and results in terms of germanium and silicon spectra, and form of the 76 Kr)

  16. Dilution physics modeling: Dissolution/precipitation chemistry

    International Nuclear Information System (INIS)

    Onishi, Y.; Reid, H.C.; Trent, D.S.

    1995-09-01

    This report documents progress made to date on integrating dilution/precipitation chemistry and new physical models into the TEMPEST thermal-hydraulics computer code. Implementation of dissolution/precipitation chemistry models is necessary for predicting nonhomogeneous, time-dependent, physical/chemical behavior of tank wastes with and without a variety of possible engineered remediation and mitigation activities. Such behavior includes chemical reactions, gas retention, solids resuspension, solids dissolution and generation, solids settling/rising, and convective motion of physical and chemical species. Thus this model development is important from the standpoint of predicting the consequences of various engineered activities, such as mitigation by dilution, retrieval, or pretreatment, that can affect safe operations. The integration of a dissolution/precipitation chemistry module allows the various phase species concentrations to enter into the physical calculations that affect the TEMPEST hydrodynamic flow calculations. The yield strength model of non-Newtonian sludge correlates yield to a power function of solids concentration. Likewise, shear stress is concentration-dependent, and the dissolution/precipitation chemistry calculations develop the species concentration evolution that produces fluid flow resistance changes. Dilution of waste with pure water, molar concentrations of sodium hydroxide, and other chemical streams can be analyzed for the reactive species changes and hydrodynamic flow characteristics

  17. L-MM Auger electron production in 0.3-1.6 MeV Kr-Kr collisions

    International Nuclear Information System (INIS)

    DeGroot, P.; Zarcone, M.J.; Kessel, Q.C.; Connecticut Univ., Storrs

    1987-01-01

    Relative total cross sections for Kr L-Auger electron emission are presented and compared with the corresponding X-ray data of Woerlee and Shanker and coworkers. These data sets all show the same incident ion energy dependence, indicating a constant fluorescence yield for the collision conditions under consideration. These data are also in agreement with a rotational coupling calculation by shanker and coworkers that was carried out within the framework of the one-electron molecular orbital model of Fano and Lichten. (orig.)

  18. Dissolution of heavy metals from electrostatic precipitator (ESP) dust ...

    African Journals Online (AJOL)

    SIBOO

    Key words: Fungal leaching, sponge iron, electrostatic precipitator (ESP) dust, metal dissolution. INTRODUCTION ... ability of micro organisms to transform solid compounds ..... of metals from spent lithium ion secondary batteries using A.

  19. 100-KR-1 Operable Unit focused feasibility study report

    International Nuclear Information System (INIS)

    1994-11-01

    The standard Comprehensive Environmental Response, Compensation, and Liability Act of 1980 Feasibility Study (FS) includes development and screening of alternatives and the detailed analysis of alternatives. This focused feasibility study (FFS) was conducted for the 100-KR-1 Operable Unit at the Hanford Site in southeastern Washington. The objective of this operable unit-specific FFS is to provide decision makers with sufficient information to allow appropriate and timely selection of interim remedial measures (IRM) for the five sites (116-K-1 crib, 116-K-2 trench, 116-KE-4 and 116-KW-3 retention basins, and process effluent pipelines) associated with the 100-KR-1 Operable Unit. The IRM candidate waste sites are determined in the limited field investigation. Site profiles are developed for each of these waste site. The site profiles are used in the application of the plug-in approach. The waste site either plugs into the analysis of the alternatives for the group, or deviations from the developed group alternatives are described and documented

  20. Study of Electric Monopole Transitions in $^{76,78}$Kr

    CERN Multimedia

    2002-01-01

    In the run at ISOLDE performed last August we completed the study of the decay properties of the $ 0 ^{+} _{2} $ level in $ ^{76, 78, 80}$Kr by measuring the lifetime of the $ 0 ^{+} _{2} $ level in $^{76}$Kr. This was done by applying the $\\beta \\gamma\\gamma$ (t) fast timing method to the $\\beta^{+} $-decay of $^{76}$Rb. For the first time the method was applied to proton-rich nuclei at ISOLDE. This required some special modifications of the experimental set-up previously used for the case of $\\beta^{-}$-decay due to the presence of intense annihilation radiation. The experiment has been successful and enough data have been collected for the determination of the lifetime. The analysis is in progress. From a very preliminary estimate it would appear that the lifetime value falls in the range 20-60 ps. Combining this value with the previously measured ratio \\[\\frac{B(E0; 0^{+}_{2} \\rightarrow 0^{+}_{1})}{B(E2; 0^{+}_{2} \\rightarrow 2^{+}_{1})}\\] It is possible to extract an estimate of the monopole transition...

  1. Characterization of lead nanoparticles formed by Shewanella sp. KR-12

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chien-Liang; Yen, Jui-Hung, E-mail: sonny@ntu.edu.tw [National Taiwan University, Department of Agricultural Chemistry (China)

    2016-01-15

    The bacterial strain KR-12 was isolated from river sediment in northeast Taiwan. 16S rRNA gene sequencing revealed that it belongs to the genus Shewanella. The strain can accumulate lead (Pb) and form Pb nanoparticles (PbNPs) on exposure to Pb(NO{sub 3}){sub 2} and sodium formate in HEPES buffer. On transmission electron microscopy (TEM), the KR-12-formed PbNPs were spherical in shape and ranged from 3 to 8 nm. The PbNPs formed a line or curved pattern on bacteria. In addition, one or more pilus-like structures elongated from the bacteria. In contrast, Shewanella oneidensis MR-1 and other bacteria could not form PbNPs pattern or pilus-like structure under the same conditions. High-resolution TEM combined with energy-dispersive X-ray spectroscopy demonstrated that these PbNPs primarily contained Pb and had an amorphous structure. This is the first report of the biosynthesis of PbNPs by a Shewanella species.

  2. Photoemission study of Kr 3d→np autoionization resonances

    International Nuclear Information System (INIS)

    Lindle, D.W.; Heimann, P.A.; Ferrett, T.A.; Piancastelli, M.N.; Shirley, D.A.

    1987-01-01

    Resonant photoelectron spectra of Kr have been taken in the photon-energy ranges of the 3d/sub 5/2/→5p,6p and 3d/sub 3/2/→5p excitations. The spectra, which closely resemble normal Kr + 3d/sup -1/ Auger spectra, illustrate the importance of ''spectator'' Auger-like decay for inner-shell resonances, in which the initially excited electron does not participate in the core-hole deexcitation process, except to respond to the change in the atomic potential. Possible assignments for some of the spectator decay channels are discussed based on photoemission intensity measurements at the different 3d resonances. These assignments suggest that shake-up (e.g., 5p→6p) of the ''spectator'' electron during the decay process is not quite as important as previously suspected. The resonance profiles of some of the more intense satellites have been determined over the 3d→np resonances. Very small resonance effects also were observed in the partial cross section for 4p subshell ionization, which produced asymmetric Fano-type profiles. The 4p angular distribution, in contrast, exhibits a pronounced effect in the resonance energy range. The 4p results demonstrate that nonspectator autoionization also is present

  3. Kr II laser-induced fluorescence for measuring plasma acceleration.

    Science.gov (United States)

    Hargus, W A; Azarnia, G M; Nakles, M R

    2012-10-01

    We present the application of laser-induced fluorescence of singly ionized krypton as a diagnostic technique for quantifying the electrostatic acceleration within the discharge of a laboratory cross-field plasma accelerator also known as a Hall effect thruster, which has heritage as spacecraft propulsion. The 728.98 nm Kr II transition from the metastable 5d(4)D(7/2) to the 5p(4)P(5/2)(∘) state was used for the measurement of laser-induced fluorescence within the plasma discharge. From these measurements, it is possible to measure velocity as krypton ions are accelerated from near rest to approximately 21 km/s (190 eV). Ion temperature and the ion velocity distributions may also be extracted from the fluorescence data since available hyperfine splitting data allow for the Kr II 5d(4)D(7/2)-5p(4)P(5/2)(∘) transition lineshape to be modeled. From the analysis, the fluorescence lineshape appears to be a reasonable estimate for the relatively broad ion velocity distributions. However, due to an apparent overlap of the ion creation and acceleration regions within the discharge, the distributed velocity distributions increase ion temperature determination uncertainty significantly. Using the most probable ion velocity as a representative, or characteristic, measure of the ion acceleration, overall propellant energy deposition, and effective electric fields may be calculated. With this diagnostic technique, it is possible to nonintrusively characterize the ion acceleration both within the discharge and in the plume.

  4. A Kinetics Model for KrF Laser Amplifiers

    Science.gov (United States)

    Giuliani, J. L.; Kepple, P.; Lehmberg, R.; Obenschain, S. P.; Petrov, G.

    1999-11-01

    A computer kinetics code has been developed to model the temporal and spatial behavior of an e-beam pumped KrF laser amplifier. The deposition of the primary beam electrons is assumed to be spatially uniform and the energy distribution function of the nascent electron population is calculated to be near Maxwellian below 10 eV. For an initial Kr/Ar/F2 composition, the code calculates the densities of 24 species subject to over 100 reactions with 1-D spatial resolution (typically 16 zones) along the longitudinal lasing axis. Enthalpy accounting for each process is performed to partition the energy into internal, thermal, and radiative components. The electron as well as the heavy particle temperatures are followed for energy conservation and excitation rates. Transport of the lasing photons is performed along the axis on a dense subgrid using the method of characteristics. Amplified spontaneous emission is calculated using a discrete ordinates approach and includes contributions to the local intensity from the whole amplifier volume. Specular reflection off side walls and the rear mirror are included. Results of the model will be compared with data from the NRL NIKE laser and other published results.

  5. Study of the diamond and diamond like films formation and technology development for the films precipitation on solid surface for wear resistance increasing of tools, machine and mechanism parts

    International Nuclear Information System (INIS)

    Imanbekov, Z.; Bekmuhambetov, E.

    1996-01-01

    Purpose of the project: The purpose of the project is a development and a creation of an effective technology of the diamond and diamond like films precipitation on materials, including refractory metals, semiconductors and composite on the carbon fibers base. The study method includes the experimental investigation of the base surface structure and properties, preparation of the surface for diamond and diamond like coats growing. The precipitation of above mentioned films will be carried out from the plasma being formed from carbon gas medium at low pressure. The main purposes of the project are: - development of the technology for obtaining the films with specified properties; provision of required rate -of the precipitation; - decreasing of temperature; - manufacturing of the functioning laboratory stand with further developing of a pilot- - commercial plant for diamond and diamond like coating. It is supposed to develop a method of the monocrystal diamond films growing, that are useful for semiconductor devices manufacturing The methods: A thermo-emission and ECR methods will be used for investigation of the diamond and diamond like films formation and growth processes. The plant that will be used for the first method is a two electrode construction. Refractory metals (W,Re) being heated up to 2500 Kelvin degrees, are usually used as an actuating electrode. The second one is a base on which the precipitation is carrying out. Refractory metals, steel, silicon can be used as the base. Actuating medium is a mixture of carbon and inert gases. The second method is based on a principle of a plasma formation with use of 2.45 GHz Shf radiation power. An ECR-plasma is formed in conjunction with magnetic field in the actuating chamber. This method allows to precipitate high quality films at lower pressure. Expected results: The main purpose of the project is to assimilate the high effective technology of the diamond and diamond like films precipitation on different

  6. Conceptual design of an angular multiplexed 50 kJ KrF amplifier for ICF

    International Nuclear Information System (INIS)

    Lowenthal, D.D.; Ewing, J.J.; Center, R.E.; Mumola, P.; Olson, T.

    1981-01-01

    The results of a conceptual design for an angular multiplexed 50 kJ KrF amplifier for ICF are presented. Optical designs, amplifier scaling with a KrF kinetics code and limitations imposed by pulsed power technology are described

  7. Laboratory sensor design for fiber-optic detection of 85Kr

    International Nuclear Information System (INIS)

    Geelhood, B.D.; Knopf, M.A.

    1994-06-01

    The goal of the fiber-optic detection of 85 Kr project is to produce a sensor to detect 85 Kr in real-time from either an airborne or ground-based platform. The 85 Kr gas is a fission product which is released in large quantities during fuel reprocessing and in minor quantities during nuclear reactor operations. Thus an airborne plume of 85 Kr is a radioactive signature of proliferation. Since 85 Kr has a 10.72 year half life, it is difficult for a proliferator to contain the gas for several half lives to avoid releasing the radioactive signature of proliferation. The long half life also results in a plume that can extend several kilometers from the source, which allows initial proliferation monitoring from large distances. The sensor can be used to make stand-alone, real-time measurements of 85 Kr that can be used as direct evidence for proliferation and/or as a screening sensor to determine when to collect air samples for further laboratory analysis. This report provides a summary of the 85 Kr beta sensor design that PNL will use in the laboratory to: (1) demonstrate the measurement technique, (2) establish minimum detection limits, and (3) optimize the sensor design for the final airborne sensor package. The goal of the final airborne sensor package will be to measure 85 Kr at activity levels as low as or as close to ambient background levels as possible with a reasonably sized sensor

  8. Microscopic study of low-lying collective bands in 77Kr

    Indian Academy of Sciences (India)

    Extensive experimental studies of 77Kr have recently been performed by Sylvan et al [4] and Johnson et al [5] (see also refs [6,7]). These experimental studies have resulted in the identification of positive parity and negative parity collective bands up to very high spin. The ground state for 77Kr is based on K = 5/2+ with the.

  9. High gain direct drive target designs and supporting experiments with KrF

    International Nuclear Information System (INIS)

    Karasik, Max; Bates, Jason W.; Aglitskiy, Yefim

    2013-01-01

    Krypton-fluoride laser is an attractive inertial fusion energy driver from the standpoint of target physics. Target designs taking advantage of zooming, shock ignition, and favorable physics with KrF reach energy gains of 200 with sub-MJ laser energy. The designs are robust under 2D simulations. Experiments on the Nike KrF laser support the physics basis. (author)

  10. Design, development and calibration of a radioactive gas (85Kr) detector for continuous environmental monitoring

    International Nuclear Information System (INIS)

    Janardhanan, S.; Swaminathan, N.; John, Jacob; Kutty, K.N.; Wattamwar, S.B.; Gopalan, C.S.; Menezes, C.M.

    1982-01-01

    Design, development and calibration of a scintillation type detector for environmental monitoring of low levels of 85 Kr activity in off-line effluents or plant areas in presence of gamma background are reported. Calibration of the system was done using NBS 85 Kr standard. (author)

  11. Design, development and calibration of a radioactive gas (/sup 85/Kr) detector for continuous environmental monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Janardhanan, S.; Swaminathan, N.; John, J.; Kutty, K.N.; Wattamwar, S.B. (Bhabha Atomic Research Centre, Bombay (India). Health Physics Div.); Gopalan, C.S.; Menezes, C.M. (Bhabha Atomic Research Centre, Bombay (India). Electronics Div.)

    Design, development and calibration of a scintillation type detector for environmental monitoring of low levels of /sup 85/Kr activity in off-line effluents or plant areas in presence of gamma background are reported. Calibration of the system was done using NBS /sup 85/Kr standard.

  12. Long pulse KrCl laser with a high discharge quality

    NARCIS (Netherlands)

    Casper, L.C.; Bastiaens, Hubertus M.J.; Peters, P.J.M.; Boller, Klaus J.; Hofstra, R.M.

    2007-01-01

    The discharge quality and optimum pump parameters of a long-pulse high-pressure gas discharge excited KrCl laser are investigated. A three-electrode prepulse–mainpulse excitation circuit is employed as pump source. The discharge volume contains a gas mixture of HCl/Kr/Ne operated at a total pressure

  13. Feasibility of evaluating possible 85Kr environmental contamination from neon lamp production line to be installed

    International Nuclear Information System (INIS)

    Li Guangzuo

    1989-01-01

    Using a simplified method, the concentrations of 85 Kr leaking into the air of a workshop and its surroundings, where a neon lamp production line was to be installed, were calculated. The doses to the workers and inhabitants nearby were also estimated. Thus, the evaluation of 85 Kr enviromental contamination caused by imported equipments was made feasible

  14. Kr and Xe isotopes from spontaneous fission of 248Cm and 250Cf

    International Nuclear Information System (INIS)

    Srinivasan, B.

    1980-01-01

    Relative yields of Kr and Xe isotopes from the spontaneous fission of 248 Cm and 250 Cf have been determined mass spectrometrically. The yields are as follows: 83 Kr/ 84 Kr/ 85 Kr/ 86 Kr = 0.223/0.458/0.596/ identical 1.00 and 0.306/0.582/0.793/ identical 1.00; 131 Xe/ 134 Xe/ 136 Xe = 0.486/0.819/1.075 identical 1.00 and 0.343/0.506/0.851/ identical 1.00 from 248 Cm and 250 Cf, respectively. The Xe yields from 248 Cm agree with an earlier determination by Leich et al. Neither of these yield patterns matches that of fissiogenic Kr and Xe in carbonaceous chondrites and hence 248 Cm and 250 Cf are ruled out as progenitors of the meteoritic Kr and Xe. In general, none of the spontaneously fissioning nuclides of actinide elements can be identified as a possible progenitor. Even the mixtures of actinides, including a combination of 248 Cm and 250 Cm, are unsuitable. The origin of anomalous Kr and Xe in carbonaceous chondrites must then be traced either to the spontaneous fission of a superheavy element or to peculiarities in specific nucleosynthetic reactions. (orig.)

  15. Influence of precipitation on the Portevin-Le Chatelier effect in Al-Mg alloys

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    In the alloy with solute content higher than the limiting solubility,the solute atoms that have failed to dissolve will precipitate from the solid solution and form precipitations.In this study, the Portevin-Le Chatelier(PLC) effects in annealed 5456 and 5052 aluminum alloys with different precipitation contents have been investigated under different applied strain rates.The results suggest that precipitations have significant effect on the PLC effect and the more the precipitations are, the greater the ...

  16. Measurement of sequential change of regional ventilation by new developed Kr-81m method in asthmatics

    International Nuclear Information System (INIS)

    Shimada, Takao; Narita, Hiroto; Ishida, Hirohide; Terashima, Yoichi; Hirasawa, Korenori; Mori, Yutaka; Kawakami, Kenji

    1991-01-01

    Fazio has reported the distribution of Kr-81m by the continuous inhalation method indicates distribution of ventilation. To estimate sequential ventilation change with the continuous Kr-81m inhalation method, it is necessary to keep the concentration of Kr-81m constant. However this is frequently ignored. Because of this, we have developed the new method to maintain constant concentration of Kr-81m and compared the reliability of this method to the conventional method. The results of phantom study showed that the concentration of Kr-81m is kept constant, and sequential change of ventilation can be estimated only by our new method. On application of this method in asthmatics, we have discovered the existence of the region where ventilation reduced by inhalation of a bronchodilator. (author)

  17. Zeolitic Imidazolate Framework-8 (ZIF-8) Membranes for Kr/Xe Separation

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Ting; Feng, Xuhui; Elsaidi, Sameh K.; Thallapally, Praveen K.; Carreon, Moises A.

    2017-01-30

    Herein, we demonstrate that a prototypical type of metal organic framework, zeolitic imidazolate framework-8 (ZIF-8), in membrane form, can effectively separate Kr/Xe gas mixtures at industrially relevant compositions. The best membranes separated Kr/Xe mixtures with average Kr permeances as high as 1.5 × 10-8 ± 0.2 mol/m2 s Pa and average separation selectivities of 14.2 ± 1.9 for molar feed compositions corresponding to Kr/Xe ratio encountered typically in air. Molecular sieving, competitive adsorption, and differences in diffusivities were identified as the prevailing separation mechanisms. These membranes potentially represent a less-energy-intensive alternative to cryogenic distillation, which is the benchmark technology used to separate this challenging gas mixture. To our best knowledge, this is the first example of any metal organic membrane composition displaying separation ability for Kr/Xe gas mixtures.

  18. Calibration of the NEXT-White Detector using $^{83m}\\mathrm{Kr}$ Decays

    Energy Technology Data Exchange (ETDEWEB)

    Martínez-Lema, G.; et al.

    2018-04-05

    The NEXT-White (NEW) detector is currently the largest radio-pure high pressure gas xenon time projection chamber with electroluminescent readout in the world. NEXT-White has been operating at Laboratorio Subterr\\'aneo de Canfranc (LSC) since October 2016. This paper describes the calibrations performed with $^{83m}\\mathrm{Kr}$ decays during a long run taken from March to November 2017 (Run II). Krypton calibrations are used to correct for the finite drift-electron lifetime as well as for the dependence of the measured energy on the event position which is mainly caused by variations in solid angle coverage. After producing calibration maps to correct for both effects we measure an excellent energy resolution for 41.5 keV point-like deposits of (4.55 $\\pm$ 0.01) % FWHM in the full chamber and (3.88 $\\pm$ 0.04) % FWHM in a restricted fiducial volume. Using naive 1/$\\sqrt{E}$ scaling, these values translate into FWHM resolutions of (0.592 $\\pm$ 0.001) % FWHM and (0.504 $\\pm$ 0.005) % at the $Q_{\\beta\\beta}$ energy of xenon double beta decay (2458 keV), well within range of our target value of 1%.

  19. Monolayer Adsorption of Ar and Kr on Graphite: Theoretical Isotherms and Spreading Pressures

    Science.gov (United States)

    Mulero; Cuadros

    1997-02-01

    The validity of analytical equations for two-dimensional fluids in the prediction of monolayer adsorption isotherms and spreading pressures of rare gases on graphite is analyzed. The statistical mechanical theory of Steele is used to relate the properties of the adsorbed and two-dimensional fluids. In such theory the model of graphite is a perfectly flat surface, which means that only the first order contribution of the fluid-solid interactions are taken into account. Two analytical equations for two-dimensional Lennard-Jones fluids are used: one proposed by Reddy-O'Shea, based in the fit on pressure and potential energy computer simulated results, and other proposed by Cuadros-Mulero, based in the fit of the Helmholtz free energy calculated from computer simulated results of the radial distribution function. The theoretical results are compared with experimental results of Constabaris et al. (J. Chem. Phys. 37, 915 (1962)) for Ar and of Putnam and Fort (J. Phys. Chem. 79, 459 (1975)) for Kr. Good agreement is found using both equations in both cases.

  20. Van der Waals bond in dimers: H2Ne, H2Ar, H2Kr

    International Nuclear Information System (INIS)

    Waaijer, M.

    1981-01-01

    The H 2 -inert gas dimers H 2 X, and particularly H 2 Ne, H 2 Ar and H 2 Kr, form the subject of this thesis and are loosely bound van der Waals complexes, which is reflected in the low number of bound states and the small anisotropic interaction. The H 2 X dimers studied are formed in a supersonic nozzle expansion, in which the internal energy is converted into the macroscopic flow energy, establishing an internal temperature drop to 3 K, which favours dimer formation. Because of this cooling the H 2 X dimers relax to the lowest rotational states. The hyperfine transitions have been measured using magnetic beam resonance and yield information about the isotropic as well as the anisotropic intermolecular potential in the range between the classical turning points and in the adjacent part of the repulsive branch. The sensitivity of the method is very high and slight changes in the intermolecular potential cause significant effects. The analysis of the measured hyperfine transitions incorporates all interacting states of the molecule, bound as well as unbound (continuum) states. For H 2 Ne, which is the best studied H 2 -inert gas system from the experimental point of view, the author succeeded in establishing an intermolecular potential, that provides a solid ground for comparison with future ab initio calculations. (Auth.)

  1. Laser Plasma Instability (LPI) Driven Light Scattering Measurements with Nike KrF Laser

    Science.gov (United States)

    Oh, J.; Weaver, J. L.; Kehne, D. M.; Obenschain, S. P.; McLean, E. A.; Lehmberg, R. H.

    2008-11-01

    With the short wavelength (248 nm), large bandwidth (1˜2 THz), and ISI beam smoothing, Nike KrF laser is expected to have higher LPI thresholds than observed at other laser facilities. Previous measurements using the Nike laser [J. L. Weaver et al, Phys. Plasmas 14, 056316 (2007)] showed no LPI evidence from CH targets up to I˜2x10^15 W/cm^2. For further experiments to detect LPI excitation, Nike capabilities have been extended to achieve higher laser intensities by tighter beam focusing and higher power pulses. This talk will present results of a recent LPI experiment with the extended Nike capabilities focusing on light emission data in spectral ranges relevant to the Raman (SRS) and Two-Plasmon Decay (TPD) instabilities. The primary diagnostics were time-resolved spectrometers with an absolute-intensity-calibrated photodiode array in (0.4˜0.8)φ0 and a streak camera near 0.5φ0. The measurements were conducted at laser intensities of 10^15˜10^16 W/cm^2 on planar targets of CH solids and RF foams.

  2. Cerium oxalate precipitation

    International Nuclear Information System (INIS)

    Chang, T.P.

    1987-02-01

    Cerium, a nonradioactive, common stand-in for plutonium in development work, has been used to simulate several plutonium precipitation processes at the Savannah River Laboratory. There are similarities between the plutonium trifluoride and the cerium oxalate precipitations in particle size and extent of plating, but not particle morphology. The equilibrium solubility, precipitation kinetics, particle size, extent of plating, and dissolution characteristics of cerium oxalate have been investigated. Interpretations of particle size and plating based on precipitation kinetics (i.e., nucleation and crystal growth) are presented. 16 refs., 7 figs., 6 tabs

  3. Inhalation scan using sup(81m)Kr-gas

    International Nuclear Information System (INIS)

    Kobayashi, Hidetoshi; Sasaki, Tsuneo; Senda, Kohei; Ohara, Ken; Kaii, Osamu

    1979-01-01

    Inhalation scan using sup(81m) Kr-gas was performed in the various pulmonary diseases, in order to examine the ventilatory function of the lung after the measurement of ratio of expiratory ratio in the normal and diseased lung field. Inhalation scan is applied to the various pulmonary diseases such as lung cancer, radiation pulmonary fibrosis and chronic obstructive pulmonary disease. In cases of lung cancer, there is disturbance of respiratory function at the site of lesion when compared to the remainder of the normal lung fields. In cases of chronic obstructive pulmonary disease, the inhalation scan is performed at three states such as pre-, in- and post-attack of the disease. During the asthma attack the respiratory function is disturbed considerably when compared to the pre- and post-attack states. In each pulmonary disease, the ratio of expiratory ratio is measured from the histogram and pulmonary function is evaluated. (author)

  4. Comparison of observed and predicted Kr-85 air concentrations

    International Nuclear Information System (INIS)

    Yildiran, M.; Miller, C.W.

    1984-01-01

    A computer code, ANEMOS has been written to estimate concentrations in air and ground deposition rates for Atmospheric Nuclides Emitted from Multiple Operation Sources. This code uses a modified Gaussian plume equation. Output from ANEMOS includes annual-average air concentrations and ground deposition rates of dispersed radionuclides and daughters. To use the environmental transport model properly, some estimate of the models predictive accuracy must be obtained. To validate the ANEMOS model, one year of weekly average Kr-85 concentrations observed at 13 stations located 28 to 144 km distant from continuous point source at the Savannah River Plant have been used. There was a general tendency for the model to underpredict the observed air concentrations slightly. Pearson's correlation between pairs of logarithms of observed and predicted annual-average values was r=0.84. The monthly results tend to show more scatter than do either the seasonal or the annual comparisons. (orig.)

  5. Kr-PLIF for scalar imaging in supersonic flows.

    Science.gov (United States)

    Narayanaswamy, V; Burns, R; Clemens, N T

    2011-11-01

    Experiments were performed to explore the use of two-photon planar laser-induced fluorescence (PLIF) of krypton gas for applications of scalar imaging in supersonic flows. Experiments were performed in an underexpanded jet of krypton, which exhibited a wide range of conditions, from subsonic to hypersonic. Excellent signal-to-noise ratios were obtained, showing the technique is suitable for single-shot imaging. The data were used to infer the distribution of gas density and temperature by correcting the fluorescence signal for quenching effects and using isentropic relations. The centerline variation of the density and temperature from the experiments agree very well with those predicted with an empirical correlation and a CFD simulation (FLUENT). Overall, the high signal levels and quantifiable measurements indicate that Kr-PLIF could be an effective scalar marker for use in supersonic and hypersonic flow applications.

  6. A new site for 85Kr measurements on groundwater samples

    International Nuclear Information System (INIS)

    Lange, T.; Hebert, D.

    2001-01-01

    As a part of a new 85 Kr laboratory, which is currently being established at the Institute of Applied Physics in Freiberg, Germany, a modified CO 2 extractor for krypton sampling is used. The operation principle is simple and contamination-safe with a reasonable effort. Continuously pumped under pressure, the water passes a Venturi-type nozzle and degasses due to relaxing. The extracted gas mixture then enters a recirculation system flowing through a CO 2 trap (NaOH), molecular sieves and a cooled charcoal trap, where krypton and other components are adsorbed. Remaining gases reenter the system at the Venturi-type nozzle. To keep the circulation alive an additional helium support is needed. In a simple field experiment, extraction efficiencies up to 0.8 for 222 Rn have been measured.

  7. A new site for 85Kr measurements on groundwater samples

    Science.gov (United States)

    Lange, T.; Hebert, D.

    2001-06-01

    As a part of a new 85Kr laboratory, which is currently being established at the Institute of Applied Physics in Freiberg, Germany, a modified CO 2 extractor for krypton sampling is used. The operation principle is simple and contamination-safe with a reasonable effort. Continuously pumped under pressure, the water passes a Venturi-type nozzle and degasses due to relaxing. The extracted gas mixture then enters a recirculation system flowing through a CO 2 trap (NaOH), molecular sieves and a cooled charcoal trap, where krypton and other components are adsorbed. Remaining gases reenter the system at the Venturi-type nozzle. To keep the circulation alive an additional helium support is needed. In a simple field experiment, extraction efficiencies up to 0.8 for 222Rn have been measured.

  8. Energies and lifetimes of excited states in copperlike Kr VIII

    International Nuclear Information System (INIS)

    Livingston, A.E.; Curtis, L.J.; Schectman, R.M.; Berry, H.G.

    1980-01-01

    The spectrum of Kr VIII has been observed between 180 and 2000 A by using foil excitation of 2.5--3.5-MeV krypton ions. Twenty new transitions have been classified and eleven new excited-state energies have been determined within the n=4 --7 shells. The ionization potential is derived to be 1 015 800 +- 200 cm -1 . The excited-state energies and fine structures are compared with recent relativistic Hartree-Fock calculations. The 4p-state lifetime has been measured by performing a simultaneous analysis of decay data for the 4p level and for its dominant cascade-repopulating levels. The 4p lifetime is found to be 30% shorter than previously measured values and is in excellent agreement with the result of a recent multiconfiguration Hartree-Fock calculation. The source of the discrepancy between this result and earlier measurements is discussed

  9. Evidence for shape coexistance in 81,83Kr

    International Nuclear Information System (INIS)

    Kemnitz, P.; Doering, J.; Funke, L.; Winter, G.; Hildingsson, L.; Jerrestam, D.; Johnson, A.; Lindblad, Th.

    1984-01-01

    In the course of systematic investication of few-particle and collective states in the mass 80 region, the excitations in 81 , 83 Kr have been studied in-beam via (α,3n) reactions. Most of the data were derived from experiments at the Stockholm cyclotron, where coincidence relations, angular distributions, relative excitation functions and the linear polarization of the γ-rays were measured. To obtain precise data on the Doppler shift (DSA method) of the γ-rays, the spectra at 30 deg and 150 deg and, respectively, at 45 deg and 135 deg relative to the beam axis were measured alternatingly. Since DSA data are most reliable for the highest levels reached with a certain beam energy, additional measurements were performed at the Rossendorf cyclotron using α-particles of 27 MeV which excite lower spin states than the 42 MeV α-particles used in the main part of the experiments

  10. Comparison of observed and predicted Kr-85 air concentrations

    International Nuclear Information System (INIS)

    Yildiran, M.; Miller, C.W.

    1984-01-01

    A computer code, ANEMOS has been written to estimate concentrations in air and ground deposition rates for Atmospheric Nuclides Emitted from Multiple Operation Sources. This code uses a modified Gaussian plum equation. Output from ANEMOS includes annual-average air concentrations and ground deposition rates of dispersed radionuclides and daughters. To use the environmental transport model properly, some estimate of the models predictive accuracy must be obtained. To validate the ANEMOS model, one year of weekly average Kr-85 concentrations observed at 13 stations located 28 to 144 km distant from continuous point source at the Savannah River Plant (SRP), Aiken, South Carolina, have been used. There was a general tendency for the model to underpredict the observed air concentrations slightly. Pearsons's correlation between pairs of logarithms of observed and predicted annual-average values was r = 0.84. The monthly results tend to show more scatter than do either the seasonal or the annual comparisons. 18 references, 3 figures, 3 tables

  11. Annealing studies of Bi and Kr inclusions in Al

    Energy Technology Data Exchange (ETDEWEB)

    Bjoern Thoft, N

    1995-04-01

    This report contains the results of experimental investigations of melting, solidification and growth of Bi and Kr inclusions made by ion implantation into aluminium. The experimental techniques used of for this study were x-ray diffraction, transmission electron microscopy, Rutherford backscattering, ion channeling, and grazing-incidence small-angle x-ray scattering. The x-ray diffraction signal from crystalline Bi inclusions in Al has been recorded as a function of temperature during heating to temperatures above the bulk melting point and cooling to room temperature. Data from these measurements have been fitted using models (developed by Pawlow and Wronski) for the size-dependent melting temperature of small particles, and size distributions for the inclusions have been determined in this way. Transmission electron microscopy has confirmed the melting and solidification of the Bi inclusions in the temperature ranges, in which these processes were observed by x-ray diffraction, establishing the facts that the inclusions melt below the bulk melting point and that a large supercooling is seen. Information about the amount and depth distribution of the Bi confined in the Al matrix has been derived from Rutherford backscattering measurements. Melting and solidification of Bi inclusions have been observed by means of ion channeling. The results of the investigations of bismuth inclusions in aluminium are compared to previous, similar results for lead inclusions in aluminium. Finally, preliminary experiments have confirmed that growth of Kr inclusions in Al can be observed using grazing-incidence small-angle scattering. (au) (13 tabs., 46 ills., 77 refs.).

  12. Annealing studies of Bi and Kr inclusions in Al

    International Nuclear Information System (INIS)

    Bjoern Thoft, N.

    1995-04-01

    This report contains the results of experimental investigations of melting, solidification and growth of Bi and Kr inclusions made by ion implantation into aluminium. The experimental techniques used of for this study were x-ray diffraction, transmission electron microscopy, Rutherford backscattering, ion channeling, and grazing-incidence small-angle x-ray scattering. The x-ray diffraction signal from crystalline Bi inclusions in Al has been recorded as a function of temperature during heating to temperatures above the bulk melting point and cooling to room temperature. Data from these measurements have been fitted using models (developed by Pawlow and Wronski) for the size-dependent melting temperature of small particles, and size distributions for the inclusions have been determined in this way. Transmission electron microscopy has confirmed the melting and solidification of the Bi inclusions in the temperature ranges, in which these processes were observed by x-ray diffraction, establishing the facts that the inclusions melt below the bulk melting point and that a large supercooling is seen. Information about the amount and depth distribution of the Bi confined in the Al matrix has been derived from Rutherford backscattering measurements. Melting and solidification of Bi inclusions have been observed by means of ion channeling. The results of the investigations of bismuth inclusions in aluminium are compared to previous, similar results for lead inclusions in aluminium. Finally, preliminary experiments have confirmed that growth of Kr inclusions in Al can be observed using grazing-incidence small-angle scattering. (au) (13 tabs., 46 ills., 77 refs.)

  13. Multicollector High Precision Resolution of Primordial Kr and Xe in Mantle CO2 Well Gases

    Science.gov (United States)

    Holland, G.; Ballentine, C.; Cassidy, M.

    2008-12-01

    Noble gas isotopes in magmatic CO2 well gases provide a unique insight into mantle volatile origin and dynamics [1-3]. Previous work has resolved mantle 20Ne/22Ne ratios consistent with a solar wind irradiated meteoritic source for mantle He and Ne [1]. This is distinct from Solar Wind values that might be expected if the primary mechanism of terrestrial mantle volatile acquisition was through the gravitational capture of solar nebula gases [see 4]. Within the CO2 well gases a primordial component has also been resolved in the non- radiogenic Xe isotopic composition [2,3]. Using multicollector mass spectrometry we have observed a 124Xe/130Xe excess of 1.85 percent over air plus/minus 0.17 percent for the least air contaminated samples. At this level of precision we are for the first time able to differentiate between a trapped meteoritic origin (average carbonaceous chondrite or Q Xe) rather than Solar Wind origin as the primordial Xe component. The well gases also contain Kr which, in the least air contaminated sample, have a correlated 86Kr/82Kr excess of 0.55 percent over air plus/minus 0.04 percent. Whilst mass dependent fractionation can theoretically produce correlated excesses in 124Xe-128Xe and 82Kr-86Kr isotopes, no fractionation from air is observed in 38Ar/36Ar [3] and the Kr excesses are in the opposite sense to that of Xe. From 136Xe excesses, Kr fission yield from Pu and U can be calculated and subtracted from the Kr isotopic signature. This fission-corrected signature is most reasonably explained as a primordial component. This is the first time that primordial Kr has ever been resolved in a terrestrial sample. The primordial Kr isotopic signature is distinct from Solar Wind Kr and is consistent with the primordial Kr also originating as a trapped component within meteorites. We are now able to demonstrate that both the light (He and Ne) and Heavy (Kr and Xe) noble gas origin in the terrestrial mantle is consistent with a trapped component during the

  14. Compatibility of technologies with regulations in the waste management of H-3, I-129, C-14, and Kr-85. Part II. Analysis

    International Nuclear Information System (INIS)

    Trevorrow, L.E.; Kolba, V.M.; Vandegrift, G.F.; Steindler, M.J.

    1983-11-01

    Waste forms of 3 H, 129 I, 14 C, and 85 Kr separated from fuel reprocessing streams and procedures for managing them were analyzed regarding compliance with regulations. Transportation of these wastes in certain DOT-specification packagings would be permissible, but some of these packagings may not be acceptable in some disposal situations. Transportation of gaseous 85 Kr in a currently certified cylinder is possible, but a fuel reprocessor may wish to ship larger quantities per package. Disposal of tritium using a package designed by a DOE contractor and shallow land burial, in accord with the regulations of 10 CFR 61, seems practicable. Although 10 CFR 61 permits shallow land burial of 129 I, the concentration limit requires distribution in a volume that may seem impractical to commercial fuel reprocessors. The concentration limit of 10 CFR 61 for shallow land burial of 14 C requires distribution in a lesser, although still large, volume. For both 129 I and 14 C, management as high-level waste offers the advantage of smaller volumes. Similar advantages may be offered by greater confinement or non-near surface concepts for disposal. The concrete waste forms developed for these nuclides may not meet technical criteria being formulated for geologic disposal. The lack of accommodation of 85 Kr at disposal facilities makes storage of the gaseous form at the fuel reprocessing plant, followed by dispersal after partial decay, seem attractive. Ocean disposal of 129 I and 14 C by the rules of the International Atomic Energy Agency-London Ocean Dumping Convention offers advantages over shallow land burial: higher allowed concentrations, resulting in smaller volumes and fewer packages. These rules, however, thwart ocean disposal of 85 Kr since gaseous forms are banned, and for solid forms, concentration limits would require distribution of radioactivity in very large volumes. 80 references

  15. PRECIPITATION OF PROTACTINIUM

    Science.gov (United States)

    Moore, R.L.

    1958-07-15

    An lmprovement in the separation of protactinium from aqueous nitric acid solutions is described. 1t covers the use of lead dioxide and tin dioxide as carrier precipitates for the protactinium. In carrying out the process, divalent lead or divalent tin is addcd to the solution and oxidized, causing formation of a carrier precipitate of lead dioxide or stannic oxide, respectively.

  16. Global Precipitation Measurement Poster

    Science.gov (United States)

    Azarbarzin, Art

    2010-01-01

    This poster presents an overview of the Global Precipitation Measurement (GPM) constellation of satellites which are designed to measure the Earth's precipitation. It includes the schedule of launches for the various satellites in the constellation, and the coverage of the constellation, It also reviews the mission capabilities, and the mission science objectives.

  17. New method of 85Kr reduction in a noble gas based low-background detector

    Science.gov (United States)

    Akimov, D. Yu.; Bolozdynya, A. I.; Burenkov, A. A.; Hall, C.; Kovalenko, A. G.; Kuzminov, V. V.; Simakov, G. E.

    2017-04-01

    Krypton-85 is an anthropogenic beta-decaying isotope which produces low energy backgrounds in dark matter and neutrino experiments, especially those based upon liquid xenon. Several technologies have been developed to reduce the Kr concentration in such experiments. We propose to augment those separation technologies by first adding to the xenon an 85Kr-free sample of krypton in an amount much larger than the natural krypton that is already present. After the purification system reduces the total Kr concentration to the same level, the final 85Kr concentration will be reduced even further by the dilution factor. A test cell for measurement of the activity of various Kr samples has been assembled, and the activity of 25-year-old krypton has been measured. The measured activity agrees well with the expected activity accounting for the 85Kr abundance of the earth's atmosphere in 1990 and the half-life of the isotope. Additional tests with a Kr sample produced in the year 1944 (before the atomic era) have been done in order to demonstrate the sensitivity of the test cell.

  18. New method of 85Kr reduction in a noble gas based low-background detector

    International Nuclear Information System (INIS)

    Akimov, D.Yu.; Burenkov, A.A.; Kovalenko, A.G.; Simakov, G.E.; Bolozdynya, A.I.; Hall, C.; Kuzminov, V.V.

    2017-01-01

    Krypton-85 is an anthropogenic beta-decaying isotope which produces low energy backgrounds in dark matter and neutrino experiments, especially those based upon liquid xenon. Several technologies have been developed to reduce the Kr concentration in such experiments. We propose to augment those separation technologies by first adding to the xenon an 85 Kr-free sample of krypton in an amount much larger than the natural krypton that is already present. After the purification system reduces the total Kr concentration to the same level, the final 85 Kr concentration will be reduced even further by the dilution factor. A test cell for measurement of the activity of various Kr samples has been assembled, and the activity of 25-year-old krypton has been measured. The measured activity agrees well with the expected activity accounting for the 85 Kr abundance of the earth's atmosphere in 1990 and the half-life of the isotope. Additional tests with a Kr sample produced in the year 1944 (before the atomic era) have been done in order to demonstrate the sensitivity of the test cell.

  19. Identification of Near-infrared [Se iii] and [Kr vi] Emission Lines in Planetary Nebulae

    Energy Technology Data Exchange (ETDEWEB)

    Sterling, N. C.; Mashburn, A. L. [Department of Physics, University of West Georgia, 1601 Maple Street, Carrollton, GA 30118 (United States); Madonna, S.; García-Rojas, J.; Luridiana, V. [Instituto de Astrofísica de Canarias, E-38205 La Laguna, Tenerife (Spain); Butler, K. [Institut für Astronomie und Astrophysik, Scheinerstr. 1, D-81679 München (Germany); Morisset, C. [Instituto de Astronomía, Universidad Nacional Autonoma de Mexico, Apdo. Postal 20164, 04510 (Mexico); Roederer, I. U., E-mail: nsterlin@westga.edu, E-mail: awhite15@my.westga.edu, E-mail: vale@iaa.es, E-mail: smadonna@iac.es, E-mail: jogarcia@iac.es, E-mail: butler@usm.uni-muenchen.de, E-mail: chris.morisset@gmail.com, E-mail: iur@umich.edu [Department of Astronomy, University of Michigan, 1085 South University Avenue, Ann Arbor, MI 48109 (United States)

    2017-05-10

    We identify [Se iii] 1.0994 μ m in the planetary nebula (PN) NGC 5315 and [Kr vi] 1.2330 μ m in three PNe from spectra obtained with the Folded-Port InfraRed Echellette (FIRE) spectrometer on the 6.5 m Baade Telescope. Se and Kr are the two most widely detected neutron-capture elements in astrophysical nebulae, and can be enriched by s -process nucleosynthesis in PN progenitor stars. The detection of [Se iii] 1.0994 μ m is particularly valuable when paired with observations of [Se iv] 2.2864 μ m, as it can be used to improve the accuracy of nebular Se abundance determinations, and allows Se ionization correction factor (ICF) schemes to be empirically tested for the first time. We present new effective collision strength calculations for Se{sup 2+} and Kr{sup 5+}, which we use to compute ionic abundances. In NGC 5315, we find that the Se abundance computed from Se{sup 3+}/H{sup +} is lower than that determined with ICFs that incorporate Se{sup 2+}/H{sup +}. We compute new Kr ICFs that take Kr{sup 5+}/H{sup +} into account, by fitting correlations found in grids of Cloudy models between Kr ionic fractions and those of more abundant elements, and use these to derive Kr abundances in four PNe. Observations of [Se iii] and [Kr vi] in a larger sample of PNe, with a range of excitation levels, are needed to rigorously test the ICF prescriptions for Se and our new Kr ICFs.

  20. Core drilling of deep drillhole OL-KR50 at Olkiluoto in Eurajoki 2008

    International Nuclear Information System (INIS)

    Toropainen, V.

    2009-02-01

    As a part of the confirming site investigations at Olkiluoto, Suomen Malmi Oy (Smoy) core drilled 939.33 m and 45.44 m deep drillholes with a diameter of 75.7 mm at Olkiluoto in September - November 2008. The identification numbers of the drillholes are OL-KR50 and OL-KR50B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling water were recorded. The drill rig was computer controlled and the computer recorded drilling parameters during drilling. The objective of the measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and washing water were 1135 m 3 and 20 m 3 in the drillholes OL-KR50 and OL-KR50B, respectively. The measured volume of the returning water in the drillhole OL-KR50 was 954 m 3 . The deviation of the drillholes was measured with the deviation measuring instruments EMS and Maxibor II. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength was 129.7 MPa, the average Young's Modulus was 45.8 GPa and the average Poisson's ratio was 0.15. The main rock types were veined and diatexitic gneisses, pegmatitic granite and tonaliticgranodioritic-granitic gneiss. The average fracture frequency is 2.0 pcs/m in drillhole OL KR50 and 3.6 pcs/m in the drillhole OL-KR50B. The average RQD values are 96.1 % and 94.3 %, respectively. 39 fractured zones were penetrated by drillhole OL-KR50 and four by drillhole OL-KR50B. (orig.)

  1. New stage of search for 2Κ(2ν) capture of 78Kr

    International Nuclear Information System (INIS)

    Gavriljuk, Ju.M.; Gangapshev, A.M.; Gavrin, V.N.

    2006-01-01

    A technique to search for 2Κ capture of 78 Kr with large low-background proportional counter filled with an enriched in 78 Kr up to 99.8% at a pressure of 4.51 atm is described. The results of first measurements are presented. Analysis of data collected during 159 h yielded new limit to the half-life of 78 Kr with regard to 2Κ capture (T 1/2 ≥ 1.5 x 10 21 yr (90% C.L.)) [ru

  2. Adsorption properties of a molecular 5 A sieve for 85Kr

    International Nuclear Information System (INIS)

    Wardaszko, T.; Nidecka, J.

    1978-01-01

    The enrichment processes which are necessary at low-level 85 Kr determinations in the atmospheric air require the knowledge of adsorption properties of appropriate sorbing agents, such as a molecular 5A sieve. Following low-temperature adsorption, under specified conditions, of known amounts of 85 Kr diluted in the air, desorption was carried out and then the 85 Kr content in the temperature fraction as well as their total volume were determined. Distribution curves for the above quantities in fractions are presented. (author)

  3. Simple PVT quantitative method of Kr under high pure N2 condition

    International Nuclear Information System (INIS)

    Li Xuesong; Zhang Zibin; Wei Guanyi; Chen Liyun; Zhai Lihua

    2005-01-01

    A simple PVT quantitative method of Kr in the high pure N 2 was studied. Pressure, volume and temperature of the sample gas were measured by three individual methods to obtain the sum sample with food uncertainty. The ratio of Kr/N 2 could measured by GAM 400 quadrupole mass spectrometer. So the quantity of Kr could be calculated with the two measured data above. This method can be suited for quantitative analysis of other simple composed noble gas sample with high pure carrying gas. (authors)

  4. Modeling of Precipitation Sequence and Ageing Kinetics in Al-Mg-Si Alloys

    NARCIS (Netherlands)

    Bahrami, A.

    2010-01-01

    Al-Mg-Si alloys are heat treatable alloys in which strength is obtained by precipitation hardening. Precipitates, formed from a supersaturated solid solution during ageing heat treatment, are GP-zones, B", B´ and B-Mg2Si. Precipitation kinetics and strength vary with alloy composition and process

  5. SEP-Kr and SEP-Xe in Lunar Ilmenite and the Ar/Kr/Xe Ratio in the Solar Wind

    Science.gov (United States)

    Wieler, R.; Baur, H.; Signer, P.

    1992-07-01

    We analyzed all five noble gases in an ilmenite sample from lunar soil 71501 by closed system stepped etching (CSSE), thus extending our CSSE studies of solar noble gases (Wieler et al., 1986; Benkert et al., 1988) to Kr and Xe. He, Ne, Ar isotopes: We observe the familiar presence of two solar noble gas components: step 1 shows ^4He/^3He = 2250, ^20Ne/^22Ne = 13.8, and ^36Ar/^38Ar=5.46. The first two ratios are essentially identical to modern solar wind values (SWC; Geiss, 1973), indicating an isotopically unfractionated SW noble gas reservoir in lunar ilmenite. The Ne data-points of later steps fall on a straight line and reach the SEP-Ne point (^20Ne/^22Ne = 11.3). The slope of this line indicates mass dependent fractionation between SW-Ne and SEP-Ne. SEP-He (^4He/^3He = 4650 +-100) and SEP-Ar (^36Ar/^38Ar = 4.89+-0.05) are also observed (latter two numbers slightly revised compared to Wieler et al., 1992). Kr, Xe isotopes: Kr in those two steps that release pure SW-Ne is very slightly lighter than atmospheric Kr (^86Kr/^84Kr = 0.3041; see also Wieler et al., 1992). We interpret this to be SW-Kr in soil 71501. Steps containing (isotopically heavier) SEP-Ne likewise release heavier Kr, interpreted accordingly as SEP-Kr (^86Kr/^84Kr = 0.323). Similarly, a light Xe component is released first (SW-Xe, ^136Xe/^132Xe = 0.3003), followed by heavier SEP-Xe (^136Xe/^132Xe = 0.319). The data are consistent with both Kr and Xe in SW and SEP components to be related by mass fractionation. The relation first proposed by Benkert et al. (1988) between a ratio R(m(sub)2,m(sub)1) of two isotopes with masses m(sub)2>m(sub)1 in SW and SEP now holds for all five noble gases: (R(sub)SW-R(sub)SEP)/R(sub)SW = (2+-0.13)*(m(sub)2- m(sub)1)/m(sub)2. Since m(sub)2~m(sub)1, this relation may also be written as: R(sub)SEP/R(sub)SW ~ (m(sub)1/m(sub)2)^2 (Geiss and Bochsler, 1991). Element ratios: ^4He/^36Ar and ^20Ne/^36Ar rise from values several times below SWC to essentially SWC ratios in

  6. Precipitates in irradiated Zircaloy

    International Nuclear Information System (INIS)

    Chung, H.M.

    1985-10-01

    Precipitates in high-burnup (>20 MWd/kg U) Zircaloy spent-fuel cladding discharged from commercial boiling- and pressurized-water reactors have been characterized by TEM-HVEM. Three classes of primary precipitates were observed in the irradiated Zircaloys: Zr 3 O (2 to 6 nm), cubic-ZrO 2 (greater than or equal to 10 nm), and delta-hydride (35 to 100 nm). The former two precipitations appears to be irradiation induced in nature. Zr(Fe/sub x/Cr/sub 1-x/) 2 and Zr 2 (Fe/sub x/Ni/sub 1-x/) intermetallics, which are the primary precipitates in unirradiated Zircaloys, were largely dissolved after the high burnup. It seems, therefore, that the influence of the size and distribution of the intermetallics on the corrosion behavior may be quite different for the irradiated Zircaloys

  7. WPA Precipitation Tabulations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Hourly precipitation data tabulated under the Work Projects Administration (WPA), a New Deal program created to reduce unemployment during the Great Depression....

  8. A study of precipitation from pure solutions of uranyl nitrate

    International Nuclear Information System (INIS)

    Decrop, J.; Holder, J.; Sauteron, J.

    1961-01-01

    After its purification by extraction of the uranyl nitrate from the organic solvent, uranium has to be converted into solid form again: uranium trioxide (UO 3 ). It can be done either by thermal decomposition of uranyl nitrate or by precipitation of uranium, followed by filtration and calcination. Only the second method has been studied for now at the Bouchet plant. This paper reports the bench-scale and pilot-scale experiments of the studies of the precipitation of pure solutions of uranyl nitrate using ammonia (gaseous or in solution) or ammonium carbonate. These have been carried out at the Bouchet plant. It investigates the chemical aspect (pH, precipitates chemical composition) and the technical aspect of the different ways of precipitation (conditions of precipitation, decantation and filtration of precipitates). (M.P.)

  9. Hyperpolarized 3He MRI and 81mKr SPECT in chronic obstructive pulmonary disease

    DEFF Research Database (Denmark)

    Stavngaard, Trine; Søgaard, Lise; Mortensen, J

    2005-01-01

    visual defect score (r=0.80, pemphysema (pulmonary function test and HRCT). The defect scores were largest on 81mKr SPECT (the score on HP 3He MRI...... was to compare ventilation imaging methods in 26 patients with chronic obstructive pulmonary disease (COPD) and nine lung healthy volunteers. METHODS: HP 3He MRI, 81mKr single-photon emission computed tomography (SPECT), high-resolution computed tomography (HRCT) and pulmonary function tests were performed....... The three scans were scored visually as percentage of non-ventilated/diseased lung, and a computer-based objective measure of the ventilated volume in HP 3He MRI and 81mKr SPECT and an emphysema index in HRCT were calculated. RESULTS: We found a good correlation between HP 3He MRI and 81mKr SPECT for both...

  10. Noor koreograaf Krõõt Juurak sai imel sabast kinni / Tiiu Laks

    Index Scriptorium Estoniae

    Laks, Tiiu, 1984-

    2006-01-01

    Tantsulavastusest "Once upon" Kanuti Gildi saalis. Esietendus 12. okt. Idee ja esitus Krõõt Juurak. Valminud prooviperioodide tulemusel Viinis, PAFis Prantsusmaal ja Tallinnas. Etendub 6. dets. ka Austrias Dietheater Küntslerhausis Viinis

  11. Quadrupole collectivity beyond N = 50 in neutron- rich Se and Kr isotopes

    Science.gov (United States)

    Elman, Brandon; Gade, A.; Barofsky, D.; Bender, P. C.; Bowry, M.; Hjorth-Jensen, M.; Kemper, K. W.; Lipschutz, S.; Lunderberg, E.; Sachmpazidi, N.; Terpstra, N.; Walters, W. B.; Weisshaar, D.; Westerberg, A.; Williams, S. J.; Wimmer, K.

    2017-09-01

    We will present results on measuring the B (E 2 ;01+ ->2n+) strength for the neutron-rich 88,90Kr and 86Se isotopes from intermediate-energy Coulomb excitation. The electric quadrupole transition strengths to the first 2+ state complete, with considerably improved uncertainties, the evolution of quadrupole collectivity in the Kr and Se isotopes approaching N = 60 , for which 90Kr and 86Se had previously been the most uncertain. We also report significant excitation strength to several higher lying 2+ states in the krypton isotopes. The results confirm shell model calculations in the π (fpg) - ν (sdg) shell with only a minimally tuned shell model setup that is based on a nucleon-nucleon interaction derived from effective field theory with effective charges adjusted to 86Kr.

  12. Production and de-excitation modes of hot nuclei in the 84Kr + 12C, 84Kr + 27Al, 84Kr + Nat Ti reactions at 26.4, 34.4 and 45.4 MeV/nucleon

    International Nuclear Information System (INIS)

    Faure-Ramstein, B.

    1988-01-01

    The inclusive characteristics of nuclear fragments, of mass greater than 10 uma, from KR + C, Al and Ti reactions at 25, 35 and 45 MeV/u, are investigated. The inverse kinematic method is applied. The analysis of velocity and fragment (mass [fr

  13. Gamma-ray multiplicity moments from deeply inelastic collisions of 86Kr and 144Sm

    International Nuclear Information System (INIS)

    Christensen, P.R.; Folkmann, F.; Hansen, O.; Nathan, O.; Trautner, N.; Videlbaek, F.; Werf, S.Y.v.d.; Britt, H.C.; Chestnut, R.P.; Freiesleben, H.; Puehlhofer, F.

    1978-01-01

    First, second, and third moments of gamma-ray multiplicity distributions from deeply inelastic collisions have been measured for the system 8 6Kr on 1 44Sm at 490-MeV Kr energy. The average gamma-ray multiplicities are approx. = 21, independent of reaction angle and fragment charge. The multiplicity distributions are broad, with standard deviations of ν approx. = 10, and they have a negative skewness

  14. Core drilling of deep drillhole OL-KR57 at Olkiluoto in Eurajoki 2011-2012

    International Nuclear Information System (INIS)

    Toropainen, V.

    2012-07-01

    As a part of the confirming site investigations at Olkiluoto, Suomen Malmi Oy (Smoy) core drilled 401.71 m and 45.01 m deep drillholes, OL-KR57 and OL-KR57B, at Olkiluoto in September 2011 - January 2012. The diameter of the drillholes is 75.7 mm. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling water were recorded. The drill rig was computer controlled and the computer recorded drilling parameters during drilling. The objective of the measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling, flushing and washing water were 350 m3 and 30 m3 in the drillholes OL-KR57 and OL-KR57B, respectively. The measured volumes of the returning water in the drillholes were 328 m 3 and 16.8 m 3 , respectively. The deviations of the drillholes were measured with the deviation measuring instruments EMS and Gyro. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength was 123.9 MPa, the average Young's Modulus was 42.6 GPa and the average Poisson's ratio was 0.23. The main rock types are veined and diatexitic gneisses, mica gneiss and tonaliticgranodioritic- granitic gneiss. The average fracture frequency is 2.5 pcs/m in drillhole OL-KR57 and 3.3 pcs/m in the drillhole OL-KR57B. The average RQD values are 95.0 % and 93.0 %. Seven separate fractured zones were interpreted from OL-KR57 and three fractured zones from OL-KR57B. (orig.)

  15. Peptidoglycan crosslinking relaxation plays an important role in Staphylococcus aureus WalKR-dependent cell viability.

    Directory of Open Access Journals (Sweden)

    Aurelia Delaune

    Full Text Available The WalKR two-component system is essential for viability of Staphylococcus aureus, a major pathogen. We have shown that WalKR acts as the master controller of peptidoglycan metabolism, yet none of the identified regulon genes explain its requirement for cell viability. Transmission electron micrographs revealed cell wall thickening and aberrant division septa in the absence of WalKR, suggesting its requirement may be linked to its role in coordinating cell wall metabolism and cell division. We therefore tested whether uncoupling autolysin gene expression from WalKR-dependent regulation could compensate for its essential nature. Uncoupled expression of genes encoding lytic transglycosylases or amidases did not restore growth to a WalKR-depleted strain. We identified only two WalKR-regulon genes whose expression restored cell viability in the absence of WalKR: lytM and ssaA. Neither of these two genes are essential under our conditions and a ΔlytM ΔssaA mutant does not present any growth defect. LytM is a glycyl-glycyl endopeptidase, hydrolyzing the pentaglycine interpeptide crossbridge, and SsaA belongs to the CHAP amidase family, members of which such as LysK and LytA have been shown to have D-alanyl-glycyl endopeptidase activity, cleaving between the crossbridge and the stem peptide. Taken together, our results strongly suggest that peptidoglycan crosslinking relaxation through crossbridge hydrolysis plays a crucial role in the essential requirement of the WalKR system for cell viability.

  16. UV saturable absorber for short-pulse KrF laser systems.

    Science.gov (United States)

    Nishioka, H; Kuranishi, H; Ueda, K; Takuma, H

    1989-07-01

    A derivative of the linear tricyclic compound, acridine, is shown to be useful as a saturable absorber for short-pulse KrF lasers. The saturation characteristics and absorption recovery of a methanol solution of acridine for a 20-psec KrF laser pulse are reported. We obtain a saturation fluence of 1.2 mJ/cm(2) and a ratio of the primary to the excited absorption cross section of 6.25:1.

  17. UV saturable absorber for short-pulse KrF laser systems

    Energy Technology Data Exchange (ETDEWEB)

    Nishioka, H.; Kuranishi, H.; Ueda, K.; Takuma, H.

    1989-07-01

    A derivative of the linear tricyclic compound, acridine, is shown to beuseful as a saturable absorber for short-pulse KrF lasers. The saturationcharacteristics and absorption recovery of a methanol solution of acridine for a20-psec KrF laser pulse are reported. We obtain a saturation fluence of 1.2mJ/cm/sup 2/ and a ratio of the primary to the excited absorption cross sectionof 6.25:1.

  18. Overview of the Nike KrF laser program

    International Nuclear Information System (INIS)

    Sethian, J.D.; Lehmberg, R.H.; Pawley, C.J.; Bodner, S.E.; McLean, E.A.; Pronko, M.S.; Gerber, K.A.; Deniz, A.V.; Hardgrove, J.; McGeoch, M.W.

    1994-01-01

    Nike is a large angularly multiplexed Krypton-Fluoride (KrF) laser under development at the Naval Research Laboratory. It is designed to explore the technical and physics issues of direct drive laser fusion. When completed, Nike will deliver 2-3 kJ of 248 nm light in a 4 nsec pulse with intensities exceeding 2 x 10 14 W/cm 2 onto a planar target. Spatially and temporally incoherent light will be used to reduce the ablation pressure nonuniformities to less than 2% in the target focal plane. The Nike laser consists of a commercial oscillator/amplifier front end, an array of gas discharge amplifiers, two electron beam pumped amplifiers (one with a 20x20 cm 2 aperture, the other with a 60x60 cm 2 aperture) and the optics required to relay, encode, and decode the beam. Approximately 90% of the system is operational and currently undergoing tests: the system is complete through the 20 cm amplifier, the 60 cm amplifier has completed all the necessary electron beam/pulsed power tests, and is currently being developed into a laser amplifier, and most of the optics have been installed. It is anticipated that Nike will be fully operational in the fall of 1994

  19. Time interval measurement between two emissions: Kr + Au

    International Nuclear Information System (INIS)

    Aboufirassi, M; Bougault, R.; Brou, R.; Colin, J.; Durand, D.; Genoux-Lubain, A.; Horn, D.; Laville, J.L.; Le Brun, C.; Lecolley, J.F.; Lefebvres, F.; Lopez, O.; Louvel, M.; Mahi, M.; Steckmeyer, J.C.; Tamain, B.

    1998-01-01

    To indicate the method allowing the determination of the emission intervals, the results obtained with the Kr + Au system at 43 and 60 A.MeV are presented. The experiments were performed with the NAUTILUS exclusive detectors. Central collisions were selected by means of a relative velocity criterion to reject the events containing a forward emitted fragment. For the two bombardment energies the data analysis shows that the formation of a compound of mass around A = 200. By comparing the fragment dynamical variables with simulations one can conclude about the simultaneity of the compound deexcitation processes. It was found that a 5 MeV/A is able to reproduce the characteristics of the detected fragments. Also, it was found that to reproduce the dynamical characteristics of the fragments issued from central collisions it was not necessary to superimpose a radial collective energy upon the Coulomb and thermal motion. The distribution of the relative angles between detected fragments is used here as a chronometer. For simultaneous ruptures the small relative angles are forbidden by the Coulomb repulsion, while for sequential processes this interdiction is the more lifted the longer the interval between the two emissions is. For the system discussed here the comparison between simulation and data has been carried out for the extreme cases, i.e. for a vanishing and infinite time interval between the two emissions, respectively. More sophisticated simulations to describe angular distributions between the emitted fragments were also developed

  20. Krüppel-like factors: Three fingers in control

    Directory of Open Access Journals (Sweden)

    Swamynathan Shivalingappa K

    2010-04-01

    Full Text Available Abstract Krüppel-like factors (KLFs, members of the zinc-finger family of transcription factors capable of binding GC-rich sequences, have emerged as critical regulators of important functions all over the body. They are characterised by a highly conserved C-terminal DNA-binding motif containing three C2H2 zinc-finger domains, with variable N-terminal regulatory domains. Currently, there are 17 KLFs annotated in the human genome. In spite of their structural similarity to one another, the genes encoding different KLFs are scattered all over the genome. By virtue of their ability to activate and/or repress the expression of a large number of genes, KLFs regulate a diverse array of developmental events and cellular processes, such as erythropoiesis, cardiac remodelling, adipogenesis, maintenance of stem cells, epithelial barrier formation, control of cell proliferation and neoplasia, flow-mediated endothelial gene expression, skeletal and smooth muscle development, gluconeogenesis, monocyte activation, intestinal and conjunctival goblet cell development, retinal neuronal regeneration and neonatal lung development. Characteristic features, nomenclature, evolution and functional diversities of the human KLFs are reviewed here.

  1. Krüppel-like factors: three fingers in control.

    Science.gov (United States)

    Swamynathan, Shivalingappa K

    2010-04-01

    Krüppel-like factors (KLFs), members of the zinc-finger family of transcription factors capable of binding GC-rich sequences, have emerged as critical regulators of important functions all over the body. They are characterised by a highly conserved C-terminal DNA-binding motif containing three C2H2 zinc-finger domains, with variable N-terminal regulatory domains. Currently, there are 17 KLFs annotated in the human genome. In spite of their structural similarity to one another, the genes encoding different KLFs are scattered all over the genome. By virtue of their ability to activate and/or repress the expression of a large number of genes, KLFs regulate a diverse array of developmental events and cellular processes, such as erythropoiesis, cardiac remodelling, adipogenesis, maintenance of stem cells, epithelial barrier formation, control of cell proliferation and neoplasia, flow-mediated endothelial gene expression, skeletal and smooth muscle development, gluconeogenesis, monocyte activation, intestinal and conjunctival goblet cell development, retinal neuronal regeneration and neonatal lung development. Characteristic features, nomenclature, evolution and functional diversities of the human KLFs are reviewed here.

  2. Development of long term storage technique for recovered Kr-85, (1)

    International Nuclear Information System (INIS)

    Inada, Eiichi; Motoyama, Shigeji; Tsunoda, Naomi; Yamamoto, Keizo; Hirano, Seiji.

    1979-01-01

    The adsorption storage method of radioactive krypton Kr-85 using a double cylinder packed with activated charcoal is expected to be put into practical use as an intermediate storing method until the immobilization technique for long term storage is established. In this paper, the conceptual design of an intermediate, remote-controlled Kr-85 storage facility is presented. The features of this system are double containment, low pressure storage, and remote control. Kr-85 is at first filled into a double cylinder by the adsorbing effect of activated charcoal at low temperature (-196 deg C) by cooling with liquid nitrogen. Then, the unwelded portion of the outer cylinder containing the inner cylinder is welded and inspected to make double containment. The double cylinders are cooled by ventilation to remove the decay heat of Kr-85, and krypton leakage is always monitored. If any leakage is detected, the double cylinder is transferred to the cutting cell for the re-encapsulation of Kr-85 in a safe double cylinder. All operations are performed by remote control because of a high radiation field. The expected amount and composition of Kr-85 to be recovered from the reprocessing plant are also given as the design conditions. (Wakatsuki, Y.)

  3. Discharge-current characteristics in UV-preionized Kr/He, F2/He gas-mixtures and KrF excimer laser gas. Shigaisen yobi denri Kr/He, F2/He kongo kitai hoden oyobi KrF laser reiki hoden no denryu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, N.; Kawakami, H.; Yukimura, K. (Doshisha University, Kyoto (Japan))

    1992-08-15

    In order to study effects of Kr and F2 on discharge characteristics of KrF excimer laser gas, gap phenomena in Kr/He and F2/He gas-mixtures were observed and discharge current (I[sub d]) was measured. In the range where Kr concentration was over 10% in Kr/He gas, in which production of filamentation as well as glow discharge started, discontinuous change in I[sub d] in the second or third half cycle was observed. According to the results of experiments and model analyses, it was considered that the discontinuity of the current showed the transition point to filamentation. When F2 concentration was in the range between 0.1 and 0.3% in F2/He mixture gas, filamentation and arc with glow were observed. Sine-waveform I[sub d] ended in the first half cycle, and began to flow again after cessation or had almost constant current due to arc and others. When F2 was over 0.4%, only are discharge was observed. It was thus found that F2 has a large effect on discharge characteristics of KrF laser gas. 18 refs., 9 figs.

  4. Unique capabilities for ICF and HEDP research with the KrF laser

    Science.gov (United States)

    Obenschain, Stephen; Bates, Jason; Chan, Lop-Yung; Karasik, Max; Kehne, David; Sethian, John; Serlin, Victor; Weaver, James; Oh, Jaechul; Jenkins, Bruce; Lehmberg, Robert; Hegeler, Frank; Terrell, Stephen; Aglitskiy, Yefim; Schmitt, Andrew

    2014-10-01

    The krypton-fluoride (KrF) laser provides the shortest wavelength, broadest bandwidth and most uniform target illumination of all developed high-energy lasers. For directly driven targets these characteristics result in higher and more uniform ablation pressures as well as higher intensity thresholds for laser-plasma instability. The ISI beam smoothing scheme implemented on the NRL Nike KrF facility allows easy implementation of focal zooming where the laser radial profile is varied during the laser pulse. The capability for near continuous zooming with KrF would be valuable towards minimizing the effects of cross beam energy transport (CBET) in directly driven capsule implosions. The broad bandwidth ISI beam smoothing that is utilized with the Nike KrF facility may further inhibit certain laser plasma instability. In this presentation we will summarize our current understanding of laser target interaction with the KrF laser and the benefits it provides for ICF and certain HEDP experiments. Status and progress in high-energy KrF laser technology will also be discussed. Work supported by the Deparment of Energy, NNSA.

  5. Complex precipitation pathways in multicomponent alloys

    Energy Technology Data Exchange (ETDEWEB)

    Clouet, Emmanuel; Nastar, Maylise [Service de Recherches de Metallurgie Physique, CEA/Saclay, 91191 Gif-sur-Yvette (France); Lae, Ludovic; Deschamps, Alexis [LTPCM/ENSEEG, UMR CNRS 5614, Domaine Universitaire, BP 75, 38402 St Martin d' Heres (France); Epicier, Thierry [Groupe d' Etudes de Metallurgie Physique et de Physique des Materiaux, UMR CNRS 5510, INSA, 69621 Villeurbanne (France); Lefebvre, Williams [Groupe de Physique des Materiaux, UMR CNRS 6634, Universite de Rouen, 76801 Saint Etienne du Rouvray (France)

    2006-07-01

    One usual way to strengthen a metal is to add alloying elements and to control the size and the density of the precipitates obtained. However, precipitation in multicomponent alloys can take complex pathways depending on the relative diffusivity of solute atoms and on the relative driving forces involved. In Al - Zr - Sc alloys, atomic simulations based on first-principle calculations combined with various complementary experimental approaches working at different scales reveal a strongly inhomogeneous structure of the precipitates: owing to the much faster diffusivity of Sc compared with Zr in the solid solution, and to the absence of Zr and Sc diffusion inside the precipitates, the precipitate core is mostly Sc-rich, whereas the external shell is Zr-rich. This explains previous observations of an enhanced nucleation rate in Al - Zr - Sc alloys compared with binary Al - Sc alloys, along with much higher resistance to Ostwald ripening, two features of the utmost importance in the field of light high-strength materials. (authors)

  6. Radiation induced precipitation of the γ' phase in under-saturated nickel-silicon alloys

    International Nuclear Information System (INIS)

    Barbu, A.

    1976-01-01

    The microstructure of Ni-Si solid solutions containing 2, 4, 6, and 8at.%Si was investigated after irradiation with 500keV Ni + ions. In all samples, Ni 3 Si precipitation was found to be independent of the amount of silicon. A correspondance between interstitial loops and precipitates has been found. At low temperature the precipitates become spatially ordered. A mechanism is suggested for the formation of the precipitates [fr

  7. Time interval measurement between two emissions: Kr + Au; Mesure de l`intervalle de temps entre deux emissions: Kr + Au

    Energy Technology Data Exchange (ETDEWEB)

    Aboufirassi, M; Bougault, R.; Brou, R.; Colin, J.; Durand, D.; Genoux-Lubain, A.; Horn, D.; Laville, J.L.; Le Brun, C.; Lecolley, J.F.; Lefebvres, F.; Lopez, O.; Louvel, M.; Mahi, M.; Steckmeyer, J.C.; Tamain, B. [Lab. de Physique Corpusculaire, Caen Univ., 14 (France); LPC (Caen) - CRN (Strasbourg) - GANIL Collaboration

    1998-04-01

    To indicate the method allowing the determination of the emission intervals, the results obtained with the Kr + Au system at 43 and 60 A.MeV are presented. The experiments were performed with the NAUTILUS exclusive detectors. Central collisions were selected by means of a relative velocity criterion to reject the events containing a forward emitted fragment. For the two bombardment energies the data analysis shows that the formation of a compound of mass around A = 200. By comparing the fragment dynamical variables with simulations one can conclude about the simultaneity of the compound deexcitation processes. It was found that a 5 MeV/A is able to reproduce the characteristics of the detected fragments. Also, it was found that to reproduce the dynamical characteristics of the fragments issued from central collisions it was not necessary to superimpose a radial collective energy upon the Coulomb and thermal motion. The distribution of the relative angles between detected fragments is used here as a chronometer. For simultaneous ruptures the small relative angles are forbidden by the Coulomb repulsion, while for sequential processes this interdiction is the more lifted the longer the interval between the two emissions is. For the system discussed here the comparison between simulation and data has been carried out for the extreme cases, i.e. for a vanishing and infinite time interval between the two emissions, respectively. More sophisticated simulations to describe angular distributions between the emitted fragments were also developed 2 refs.

  8. Synthesis of core-shell molecularly imprinted polymer microspheres by precipitation polymerization for the inline molecularly imprinted solid-phase extraction of thiabendazole from citrus fruits and orange juice samples.

    Science.gov (United States)

    Barahona, Francisco; Turiel, Esther; Cormack, Peter A G; Martín-Esteban, Antonio

    2011-01-01

    In this work, the synthesis of molecularly imprinted polymer microspheres with narrow particle size distributions and core-shell morphology by a two-step precipitation polymerization procedure is described. Polydivinylbenzene (poly DVB-80) core particles were used as seed particles in the production of molecularly imprinted polymer shells by copolymerization of divinylbenzene-80 with methacrylic acid in the presence of thiabendazole (TBZ) and an appropriate porogen. Thereafter, polymer particles were packed into refillable stainless steel HPLC columns used in the development of an inline molecularly imprinted SPE method for the determination of TBZ in citrus fruits and orange juice samples. Under optimized chromatographic conditions, recoveries of TBZ within the range 81.1-106.4%, depending upon the sample, were obtained, with RSDs lower than 10%. This novel method permits the unequivocal determination of TBZ in the samples under study, according to the maximum residue levels allowed within Europe, in less than 20 min and without any need for a clean-up step in the analytical protocol. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Centrifugal precipitation chromatography

    Science.gov (United States)

    Ito, Yoichiro; Lin, Qi

    2009-01-01

    Centrifugal precipitation chromatography separates analytes according their solubility in ammonium sulfate (AS) solution and other precipitants. The separation column is made from a pair of long spiral channels partitioned with a semipermeable membrane. In a typical separation, concentrated ammonium sulfate is eluted through one channel while water is eluted through the other channel in the opposite direction. The countercurrent process forms an exponential AS concentration gradient through the water channel. Consequently, protein samples injected into the water channel is subjected to a steadily increasing AS concentration and at the critical AS concentration they are precipitated and deposited in the channel bed by the centrifugal force. Then the chromatographic separation is started by gradually reducing the AS concentration in the AS channel which lowers the AS gradient concentration in the water channel. This results in dissolution of deposited proteins which are again precipitated at an advanced critical point as they move through the channel. Consequently, proteins repeat precipitation and dissolution through a long channel and finally eluted out from the column in the order of their solubility in the AS solution. The present method has been successfully applied to a number of analytes including human serum proteins, recombinant ketosteroid isomerase, carotenoid cleavage enzymes, plasmid DNA, polysaccharide, polymerized pigments, PEG-protein conjugates, etc. The method is capable to single out the target species of proteins by affinity ligand or immunoaffinity separation. PMID:19541553

  10. Influence of damage caused by Kr ions and neutrons on electrical properties of silicon detectors

    International Nuclear Information System (INIS)

    Croitoru, N.; Gubbini, E.; Rancoita, P.G.; Rattaggi, M.; Seidman, A.

    1999-01-01

    In this paper, new measurements of physical properties of high-resistivity silicon, used in high-energy detectors, are presented. The obtained data contribute to the understanding of the causes which damage the 2electronic characteristics of the detection systems under irradiation of neutrons and ionized particles (Kr). The Hall effect coefficient (R H ) and resistivity (ρ) measurements as a function of temperature (T), for non-irradiated and irradiated by neutrons and Kr ions, were performed. The measurements of the Hall coefficient and resistivity of non-irradiated samples and irradiated at neutron fluences (PHI≤9.9x10 10 n/cm 2 ) and Kr (PHI≤7.5x10 8 Kr/cm 2 ), have shown that the obtained characteristics, R H (T) and ρ(T), are of the same shape as those known for a silicon single crystal. A slight difference of the slope of ln ρ∼ln T, for neutron- and a large difference for Kr ion irradiation as compared with that of non-irradiated samples, was observed. On increasing the irradiation to PHI larger than the value indicated above, for neutrons and Kr ions, important changes in the physical properties were observed. The resistivity increases with increasing PHI, up to a value of the same order with intrinsic silicon (ρ∼10 5 Ω cm), for both neutron and Kr ion irradiation. The values of R H increase with increasing PHI up to a fluence, for which a change of sign, from negative to positive, occurs. The variation of values of R H and ρ as a function of PHI, for neutrons and Kr ions, is similar, but the characteristics R H (PHI) and ρ(PHI), are displaced. Therefore, larger values of PHI are needed in order to obtain the same values of ρ as those for Kr ion irradiation. The dependence on T of electrical parameters of samples, irradiated at PHI≥9.9x10 10 n/cm 2 (neutrons) and PHI≥7.5x10 8 Kr/cm 3 (ions), cannot be explained, considering the usual theoretical relations. The results, obtained in these experiments, have shown a change of mechanism of

  11. Core drilling of deep borehole OL-KR43 at Olkiluoto in Eurajoki 2006

    Energy Technology Data Exchange (ETDEWEB)

    Niinimaeki, R. [Suomen Malmi Oy, Espoo (Finland)

    2006-12-15

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 1000.26 m and 45.01 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in July - October 2006. The identification numbers of the boreholes are OL-KR43 and OL-KR43B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the drilling water and the returning water were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 1103 m{sup 3} and 16 m{sup 3} in boreholes OL-KR43 and OL-KR43B, respectively. Measured volumes of the returning water were 916m{sup 3} in borehole OL-KR43 and 13m{sup 3} in borehole OL-KR43B. The deviation of the boreholes was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength is about 131 MPa, the average Young's Modulus is 37 GPa and the average Poisson's ratio is 0.19. The main rock types are veined gneiss, diatexitic gneiss

  12. Core drilling of deep borehole OL-KR46 at Olkiluoto in Eurajoki 2007

    International Nuclear Information System (INIS)

    Toropainen, V.

    2007-09-01

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 600.10 m and 45.16 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in May - June 2007. The identification numbers of the boreholes are OL-KR46 and OL-KR46B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning water, and the volume of drilling water were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 466 m 3 and 20 m 3 in boreholes OL-KR46 and OL-KR46B, respectively. Measured volumes of the returning water were 407 m 3 in borehole OL-KR46 and 12 m 3 in borehole OL-KR46B. The deviation of the boreholes was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength is 116.5 MPa, the average Young's Modulus is 31.5 GPa and the average Poisson's ratio is 0.20. The main rock types are veined gneiss, tonalitic-granodioritic-granitic gneiss and pegmatite

  13. Core drilling of deep drillhole OL-KR47 at Olkiluoto in Eurajoki 2007-2008

    International Nuclear Information System (INIS)

    Toropainen, V.

    2008-02-01

    As a part of the confirming site investigations for ONKALO rock characterisation facility, Suomen Malmi Oy (Smoy) core drilled 1008.76 m and 44.31 m deep drillholes with a diameter of 75.7 mm at Olkiluoto in October 2007 - January 2008. The identification numbers of the drillholes are OL-KR47 and OL-KR47B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling waters were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 1229 m 3 and 13.6 m 3 in drillholes OL-KR47 and OL-KR47B, respectively. Measured volume of the returning water in drillhole OL-KR47 was 1125 m 3 , water did not return in drillhole OL-KR47B. The deviation of the drillholes was measured with the deviation measuring instruments EMS and Maxibor II. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength is 92.1 MPa, the average Young's Modulus is 32.5 GPa and the average Poisson's ratio is 0.33. The main rock types are diatexitic and veined gneisses, pegmatitic granite and tonaliticgranodioritic- granitic gneiss. The average fracture frequency is 2.2 pcs / m in drillhole OL-KR47 and 3.4 pcs / m in drillhole OL-KR47B. The average RQD values were 95.3 % and 94.1 %. In drillhole OL-KR47 46 fractured zones and in drillhole OL-KR47B two fractured zones were penetrated during drilling work. (orig.)

  14. Core drilling of deep drillhole OL-KR45 at Olkiluoto in Eurajoki 2007

    International Nuclear Information System (INIS)

    Toropainen, V.

    2007-11-01

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 1023.30 m and 44.75 m deep drillholes with a diameter of 75.7 mm at Olkiluoto in June - September 2007. The identification numbers of the drillholes are OL-KR45 and OL-KR45B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling waters were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and washing water were 1186 m 3 and 19 m 3 in drillholes OL-KR45 and OL-KR45B, respectively. Measured volumes of the returning water were 962 m 3 in drillhole OL-KR45 and 15 m 3 in drillhole OL-KR45B. The deviation of the drillholes was measured with the deviation measuring instruments EMS and Maxibor II. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength is 126.2 MPa, the average Young's Modulus is 42.5 GPa and the average Poisson's ratio is 0.21. The main rock types are veined and diatexitic gneisses, pegmatitic granite and tonalitic

  15. Inhibition of calcium phosphate precipitation under environmentally-relevant conditions

    International Nuclear Information System (INIS)

    Cao Xinde; Harris, Willie G.; Josan, Manohardeep S.; Nair, Vimala D.

    2007-01-01

    Precipitation of Ca phosphates plays an important role in controlling P activity and availability in environmental systems. The purpose of this study was to determine inhibitory effects on Ca phosphate precipitation by Mg 2+ , SO 4 2- , CO 3 2- , humic acid, oxalic acid, biogenic Si, and Si-rich soil clay commonly found in soils, sediments, and waste streams. Precipitation rates were determined by measuring decrease of P concentration in solutions during the first 60 min; and precipitated solid phases identified using X-ray diffraction and electron microscopy. Poorly-crystalline hydroxyapatite (HAP: Ca 5 (PO 4 ) 3 OH) formed in control solutions over the experiment period of 24 h, following a second-order dependence on P concentration. Humic acid and Mg 2+ significantly inhibited formation of HAP, allowing formation of a more soluble amorphous Ca phosphate phase (ACP), and thus reducing the precipitation rate constants by 94-96%. Inhibition caused by Mg 2+ results from its incorporation into Ca phosphate precipitates, preventing formation of a well-crystalline phase. Humic acid likely suppressed Ca phosphate precipitation by adsorbing onto the newly-formed nuclei. Presence of oxalic acid resulted in almost complete inhibition of HAP precipitation due to preemptive Ca-oxalate formation. Carbonate substituted for phosphate, decreasing the crystallinity of HAP and thus reducing precipitation rate constant by 44%. Sulfate and Si-rich solids had less impact on formation of HAP; while they reduced precipitation in the early stage, they did not differ from the control after 24 h. Results indicate that components (e.g., Mg 2+ , humic acid) producing relatively soluble ACP are more likely to reduce P stability and precipitation rate of Ca phosphate in soils and sediments than are components (e.g., SO 4 2- , Si) that have less effect on the crystallinity

  16. The Precipitation Behavior of Poorly Water-Soluble Drugs with an Emphasis on the Digestion of Lipid Based Formulations

    DEFF Research Database (Denmark)

    Khan, Jamal; Rades, Thomas; Boyd, Ben

    2016-01-01

    digestion and drug solubilisation during gastrointestinal transit have been explored in detail, but the implications of drug precipitation beyond the potential adverse effect on bioavailability have received attention only in recent years. Specifically, these implications are that different solid forms...... the events that lead to drug precipitation during the dispersion and digestion of lipid based formulations, common methods used to inhibit precipitation, as well as conventional and newly emerging characterization techniques for studying the solid state form of the precipitated drug. Moreover, selected case...... studies are discussed where drug precipitation has ensued from the digestion of lipid based formulations, as well as the apparent link between drug ionisability and altered solid forms on precipitation, culminating in a discussion about the importance of the solid form on precipitation with relevance...

  17. Sulpyrine inhalation challenge test monitored continuously by respiratory impedance and 81mKr ventilation image

    International Nuclear Information System (INIS)

    Suenaga, Naoto; Nakamura, Hitoshi; Shiratsuki, Natsuo; Nishioka, Yasuhiro; Kitada, Osamu; Sugita, Minoru

    1993-01-01

    Continuous changes of respiratory impedance by the oscillation method using Asthograph and 81m Kr ventilation image during saline and sulpyrine solution (100 mg/ml, 250 mg/ml) provocation were simultaneously measured in 15 adult asthmatics and 7 normal individuals. Estimation of airway obstruction by respiratory impedance using Asthograph was difficult during sulpyrine inhalation, since respiratory impedance increased gradually. In addition to the measurement of respiratory impedance, images of 81m Kr ventilation were also obtained to estimate the regional ventilatory distribution. Estimation of the airway obstruction was easily obtained. Another advantage of 81m Kr ventilation image is that it can estimate the regional ventilatory distribution. The site of airway obstruction provoked by sulpyrine was observed predominantly in the lower lung field. The results of our present study were as follows. In 3 patients, increase of respiratory impedance and defect of 81m Kr ventilation image were observed. Two cases in this group were clinically diagnosed as having aspirin-induced asthma. In 7 patients, a defect of 81m Kr ventilation image was observed, but no increase of respiratory impedance was observed. Five cases in this group could not be clinically diagnosed as having aspirin-induced asthma. In 5 patients, neither defect of 81m Kr ventilation image nor increase of respiratory impedance could be detected. These results suggest that 81m Kr ventilation image on sulpyrine inhalation challenge test is a useful method for evaluating regional ventilatory distribution, but should be further investigated for application to aspirin-induced asthma. (author)

  18. Measurement of fusion excitation functions in the system {sup 78}Kr + {sup 100}Mo

    Energy Technology Data Exchange (ETDEWEB)

    Rehm, K.E.; Jiang, C.L.; Esbensen, H. [and others

    1995-08-01

    Earlier measurements of fusion reactions involving {sup 78}Kr and {sup 100}Mo projectiles and Ni-targets showed surprisingly large fusion yields at low energies which could not be explained by coupled-channels calculations. The main difference to similar measurements involving the neighboring {sup 86}Kr and {sup 92}Mo isotopes was the different slope of the excitation functions at sub-barrier energies. An analysis of a variety of experiments showed a correlation between the nuclear structure and the slope of the excitation functions, with the {open_quotes}soft{close_quotes} transitional nuclei ({sup 78}Kr, {sup 100}Mo) exhibiting shallower slopes than the {open_quotes}stiff{close_quotes} nuclei ({sup 86}Kr, {sup 92}Mo) measured at the same energies with respect to the barrier. In this experiment we studied the fusion excitation function involving two transitional nuclei {sup 78}Kr + {sup 100}Mo. The measurements were performed with {sup 78}Kr beams from the ECR source at energies between 285-370 MeV. Separation of the evaporation nucleus from the elastically scattered particles was achieved by measuring time-of-flight and magnetic rigidity in the gas-filled spectrograph. The data were completely analyzed. A comparison of the cross sections with measurements for the system {sup 86}Kr + {sup 92}Mo populating the same compound nucleus {sup 178}Pt. It shows good agreement at the highest energies, but quite different falloffs of the excitation functions toward lower energies. Coupled-channels calculations, including multi-phonon excitation for the two systems, are being performed.

  19. Irradiation-induced precipitation in Ni--Si alloys

    International Nuclear Information System (INIS)

    Barbu, A.; Ardell, A.J.

    1975-07-01

    The microstructures of Ni + ion-irradiated Ni--Si solid-solution alloys, containing 2, 4, 6 and 8 at. percent Si were investigated as a function of dose, dose-rate, and temperature. Results of transmission electron microscopy and other data show the precipitation of γ' (Ni 3 Si) in all samples irradiated at 500 0 C. Characteristics of the precipitates are described and a mechanism for their formation is suggested. (U.S.)

  20. Development of high power KrF laser for fundamental research of ICF driver and laser plasma interaction

    International Nuclear Information System (INIS)

    Wang Naiyan; Shan Yusheng; Ma Weiyi; Yao Gang; Zhou Chuangzhi; Tang Xiuzhang; Tang Zhihong; Gao Junsi; Wang Ganchang.

    1994-01-01

    A high power KrF laser system is under development in China Institute of Atomic Energy. The system consists of a front end, two-stage KrF amplifiers and two-stage Raman amplifiers, providing 100J, 1ns KrF laser with maximum average power density about 10 14 W/cm 2 on target for laser plasma interaction research. Some important technologies, such as front-end system, Angular Multiplexer, and injection locked oscillator are discussed. (author)

  1. Testing and development of transfer functions for weighing precipitation gauges in WMO-SPICE

    Directory of Open Access Journals (Sweden)

    J. Kochendorfer

    2018-02-01

    Full Text Available Weighing precipitation gauges are used widely for the measurement of all forms of precipitation, and are typically more accurate than tipping-bucket precipitation gauges. This is especially true for the measurement of solid precipitation; however, weighing precipitation gauge measurements must still be adjusted for undercatch in snowy, windy conditions. In WMO-SPICE (World Meteorological Organization Solid Precipitation InterComparison Experiment, different types of weighing precipitation gauges and shields were compared, and adjustments were determined for the undercatch of solid precipitation caused by wind. For the various combinations of gauges and shields, adjustments using both new and previously existing transfer functions were evaluated. For most of the gauge and shield combinations, previously derived transfer functions were found to perform as well as those more recently derived. This indicates that wind shield type (or lack thereof is more important in determining the magnitude of wind-induced undercatch than the type of weighing precipitation gauge. It also demonstrates the potential for widespread use of the previously developed transfer functions. Another overarching result was that, in general, the more effective shields, which were associated with smaller unadjusted errors, also produced more accurate measurements after adjustment. This indicates that although transfer functions can effectively reduce measurement biases, effective wind shielding is still required for the most accurate measurement of solid precipitation.

  2. Testing and development of transfer functions for weighing precipitation gauges in WMO-SPICE

    Science.gov (United States)

    Kochendorfer, John; Nitu, Rodica; Wolff, Mareile; Mekis, Eva; Rasmussen, Roy; Baker, Bruce; Earle, Michael E.; Reverdin, Audrey; Wong, Kai; Smith, Craig D.; Yang, Daqing; Roulet, Yves-Alain; Meyers, Tilden; Buisan, Samuel; Isaksen, Ketil; Brækkan, Ragnar; Landolt, Scott; Jachcik, Al

    2018-02-01

    Weighing precipitation gauges are used widely for the measurement of all forms of precipitation, and are typically more accurate than tipping-bucket precipitation gauges. This is especially true for the measurement of solid precipitation; however, weighing precipitation gauge measurements must still be adjusted for undercatch in snowy, windy conditions. In WMO-SPICE (World Meteorological Organization Solid Precipitation InterComparison Experiment), different types of weighing precipitation gauges and shields were compared, and adjustments were determined for the undercatch of solid precipitation caused by wind. For the various combinations of gauges and shields, adjustments using both new and previously existing transfer functions were evaluated. For most of the gauge and shield combinations, previously derived transfer functions were found to perform as well as those more recently derived. This indicates that wind shield type (or lack thereof) is more important in determining the magnitude of wind-induced undercatch than the type of weighing precipitation gauge. It also demonstrates the potential for widespread use of the previously developed transfer functions. Another overarching result was that, in general, the more effective shields, which were associated with smaller unadjusted errors, also produced more accurate measurements after adjustment. This indicates that although transfer functions can effectively reduce measurement biases, effective wind shielding is still required for the most accurate measurement of solid precipitation.

  3. Precipitation Reconstruction (PREC)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The PREC data set is an analysis of monthly precipitation constructed on a 2.5(o)lat/lon grid over the global for the period from 1948 to the present. The land...

  4. Development of Atmospheric Air 85Kr Monitoring Methodology on the Territory of the USSR

    Science.gov (United States)

    Pakhomov, Sergei; Dubasov, Yury

    2014-05-01

    Highly sensitive, low-background and high-performance method of beta-radioactivity measurements of the gas samples was developed in mid-eighties at Khlopin Radium institute. This method was based on the use of the serial automated installation for liquid scintillation measurements and special scintillating cells. Cells were equipped with the gas valve, and their internal surface were covered by a thin layer of organic scintillator. This method found was successfully was applied for 85Kr activity measurements in atmospheric krypton samples and for 85Kr concentration measurements in atmospheric air. For the first time, method developed for 85Kr activity measurements, was practically tested in May - June, 1986, while studying radioactive pollution characteristics in the air basin of Russia and Ukraine after the Chernobyl NPP accident. Thus for sampling of atmospheric krypton the industrial krypton-xenon mix manufactured at air-separating plants, located in the cities of Cherepovets, Lipetsk, Krivoi Rog and Enakiyevo was used. In the end of April and in the first half of May it was determined that 1,5-fold excess concentrations of 85Kr in atmospheric air were observed in atmospheric air of considerable part of the European territory of Russia and Ukraine During the period from 1987 to 1991 this method was used for monitoring of 85Kr on the territory of the former USSR in the air basin of Russia, Ukraine and Kazakhstan. Industrial krypton-xenon mix manufactured at 14 large air-separating plants was also used for sampling. Six of them were situated in Russia (Novomoskovsk, Lipetsk, Cherepovets, Chelyabinsk, Nizhni Tagil, Orsk). Seven - in Ukraine (Enakiyevo, Kommunarsk, Krivoi Rog, Makeyevka, Mariupol, Severodonetsk, Dneprodzerzhinsk). One plant was situated in Temirtau, in Kazakhstan. The analysis indicated that in Krivoi Rog; Dneprozhzerzhinsk; Severodonetsk; Makeyevka; Mariupol; Enakiyevo; Kommunarsk; Novomoskovsk and Cherepovets the average 85Kr concentration in

  5. Limited field investigation report for the 100-KR-4 Operable Unit

    International Nuclear Information System (INIS)

    1994-07-01

    This limited field investigation (LFI) was conducted to optimize the use of interim remedial measures (IRM) for expediting clean up while maintaining a technically sound and cost-effective program. The 100-KR-4 Operable Unit is one of four operable units associated with the 100 K Area. Operable units KR-1, KR-2 and KR-3 address contaminant sources while 100-KR-4 addresses contamination present in the underlying groundwater. The IRM decision process for groundwater operable units is based on three aspects: (1) Is the concentration greater than Hanford background? (2) Does the concentration present a medium or high human-health risk? (3) Does the concentration exceed an ecologically based applicable, relevant and appropriate requirements (ARAR) or present an environmental hazard quotient > I? The primary methods of investigation used during this LFI were the installation of monitoring wells and sampling of groundwater. The samples collected from the groundwater and soils were submitted for laboratory analysis. Boreholes were surveyed for radiological contamination using downhole geophysical techniques to further delineate the location and degree of contamination. All soil samples were screened to ascertain the presence of volatile organic compounds and radionuclides. Analytical data were subjected to validation; all first round and a minimum of 10% of subsequent round data were validated

  6. Analysis of 81Kr in groundwater using laser resonance ionization spectroscopy

    International Nuclear Information System (INIS)

    Kramer, S.D.; Hurst, G.S.; Chen, C.H.

    1985-10-01

    A new analytical technique based on resonant ionization of krypton with a vacuum ultraviolet (VUV) laser source was used to determine low-level 81 Kr concentrations in groundwater. The long half-life (210,000 years) and low concentration (1.3 x 10 3 81 Kr atoms per liter of modern water at 10 0 C) make the detection of 81 Kr by radioactive counting techniques extremely difficult. In this method, krypton gas was removed from water taken from an underground Swiss aquifer using standard cryogenic and chromatographic techniques. Stable krypton isotopes were then reduced by a factor of 10 7 by a two-stage isotopic enrichment cycle using a commercially available mass spectrometer. The enriched gas containing about 10 8 stable krypton atoms and about 10 3 atoms of 81 Kr was implanted into a silicon disc. This disc was then placed in the high vacuum final counting chamber and the krypton was released by laser annealing. This chamber contained a quadrupole mass spectrometer which used a pulsed VUV laser source as the ionizer. The measured signal indicated that the sample contained 1200 (+-300) atoms of 81 Kr

  7. Multiple photoionization from 3p excitation of Kr and 4p excitation of Xe

    International Nuclear Information System (INIS)

    Hayaishi, T.

    1986-01-01

    The photoionization cross sections for multiply charged ions produced by 3p excitation of Kr and 4p excitation of Xe have been obtained by means of a time-of-flight mass spectrometer and synchrotron radiation. It is found that the main formation of doubly to quadruply charged ions in both Kr and Xe is caused from the each initial p-hole state through a Coster-Kronig transition followed by Auger of double Auger processes. The formation of singly charged ions in these excitation energy regions is caused by direct photoionization from outermost shell electrons in both Kr and Xe. Triply charged ions are prominently produced among the multiply charged ions. The quadruple photoionization cross sections show clearly the structures due to the Rydberg series, 3p -1 nl of Kr and 4p -1 nl of Xe. Their main structures were assigned to the 3p -1 nd series in Kr and the 4p -1 nd series in Xe. (orig.)

  8. Diagnostic significance of lung ventilation study with sup(81m)Kr gas

    International Nuclear Information System (INIS)

    Narabayashi, Isamu; Ito, Yasuhiko; Ohtsuka, Nobuaki; Muranaka, Akira; Yokobayashi, Tsuneo

    1979-01-01

    Lung ventilation study was performed on 43 patients by the continuous inhalation of sup(81m)Kr gas from a 81 Rb-sup(81m)Kr generator (Nihon Mediphysics Inc. Hyogo Japan). The patients were measured in a sitting position using a scintillation camera in conjunction with a data processor. In 37 cases, scintigraphic findings were compared with those of sup(99m)Tc-MAA images. We discussed the ventilation/perfusion mismatching cases, especially in those of the pulmonary arterial abnormarity and lung cancer. In some of the discrepancy between ventilation and perfusion, nuclear angiography with sup(99m)Tc-HSA was performed. The following results were obtained by those studies. 1) The distribution of sup(81m)Kr gas within the lung is considered proportional to regional ventilation because of a short half life of sup(81m)Kr (13 seconds). 2) The ventilation image with sup(81m)Kr gas was clearly visualized because of the lower gamma-ray energy and much accumulation of activity. 3) Combined use of ventilation-perfusion scintigraphy and nuclear angiography often gave us new additional informations about the pathophysiological condition of lung. 4) In mismatching cases of lung cancer, perfusion was usually more impaired than ventilation. (author)

  9. Development and validation of a rapid HPLC method for the determination of cefdinir in beagle dog plasma integrated with an automatic on-line solid-phase extraction following protein precipitation in the 96-well plate format.

    Science.gov (United States)

    Li, Ji; Wang, Li; Chen, Zhao; Xie, Rui; Li, You; Hang, Taijun; Fan, Guorong

    2012-05-01

    The high-performance liquid chromatography (HPLC) coupled with on-line solid phase extraction (SPE) and ultraviolet (UV) detection was developed for determining cefdinir in beagle dog plasma. After simple pretreatment for plasma with 6% perchloric acid, a volume of 100 μL upper layer of the plasma sample was injected into the self-made on-line SPE column. The analytes were retained on the trap column (Lichrospher C(18), 4.6 mm × 37 mm, 25 μm), and the biological matrix was washed out with the solvent (20mM KH(2)PO(4) adjusted pH 3.0) at flow rate of 2 mL/min. By rotation of the switching valve, the target analytes could be eluted from trap column to analytical column in the back-flush mode by the mobile phase (methanol-acetonitrile-20mM KH(2)PO(4) adjusted pH 3.0, 11.25:6.75:82, v/v/v) at flow rate of 1.5 mL/min, and then separated on the analytical column (Ultimate XB-C(18), 4.6 mm × 50 mm, 5 μm). The complete cycle of the on-line SPE preconcentration, purification and HPLC separation of the analytes was 4 min. The UV detection was performed at 286 nm. The calibration curves showed excellent linear relationship (R(2)=0.9995) over the concentration range of 0.05-50 μg/mL. The optimized method showed good performance in terms of specificity, linearity, detection and quantification limits, precision and accuracy. This method was successfully applied to quantify cefdinir in beagle dog plasma to support the pre-clinical pharmacokinetic trial. Copyright © 2012. Published by Elsevier B.V.

  10. Precipitation of plutonium from acidic solutions using magnesium oxide

    International Nuclear Information System (INIS)

    Jones, S.A.

    1994-01-01

    Plutonium (IV) is only marginally soluble in alkaline solution. Precipitation of plutonium using sodium or potassium hydroxide to neutralize acidic solutions produces a gelatinous solid that is difficult to filter and an endpoint that is difficult to control. If the pH of the solution is too high, additional species precipitate producing an increased volume of solids separated. The use of magnesium oxide as a reagent has advantages. It is added as a solid (volume of liquid waste produced is minimized), the pH is self-limiting (pH does not exceed about 8.5), and the solids precipitated are more granular (larger particle size) than those produced using KOH or NaOH. Following precipitation, the raffinate is expected to meet criteria for disposal to tank farms. The solid will be heated in a furnace to dry it and convert any hydroxide salts to the oxide form. The material will be cooled in a desiccator. The material is expected to meet vault storage criteria

  11. Aurora multikilojoule KrF laser system prototype for inertial confinement fusion

    International Nuclear Information System (INIS)

    Rosocha, L.A.; Hanlon, J.A.; Mc Leod, J.; Kang, M.; Kortegaard, B.L.; Burrows, M.D.; Bowling, P.S.

    1987-01-01

    Aurora is the Los Alamos National Laboratory short-pulse, high-power, KrF laser system. It serves as an end-to-end technology demonstration for large-scale ultraviolet laser systems of interest for short wavelength, inertial confinement fusion (ICF) investigations. The systems is a prototype for using optical angular multiplexing and serial amplification by large electron-beam-driven KrF laser amplifiers to deliver stacked, 248-nm, 5-ns duration multikilojoule laser pulses to ICF targets using an --1-km-long optical beam path. The entire Aurora KrF laser system is described and the design features of the following major system components are summarized: front-end lasers, amplifier train, multiplexer, optical relay train, demultiplexer, target irradiation apparatus, and alignment and controls systems

  12. Design optimization of single-main-amplifier KrF laser-fusion systems

    International Nuclear Information System (INIS)

    Harris, D.B.; Pendergrass, J.H.

    1985-01-01

    KrF lasers appear to be a very promising laser fusion driver for commercial applications. The Large Amplifier Module for the Aurora Laser System at Los Alamos is the largest KrF laser in the world and is currently operating at 5 kJ with 10 to 15 kJ eventually expected. The next generation system is anticipated to be a single-main-amplifier system that generates approximately 100 kJ. This paper examines the cost and efficiency tradeoffs for a complete single-main-amplifier KrF laser fusion experimental facility. It has been found that a 7% efficient $310/joule complete laser-fusion system is possible by using large amplifier modules and high optical fluences

  13. Evidence of interatomic Coulombic decay in ArKr after Ar 2p Auger decay

    International Nuclear Information System (INIS)

    Morishita, Y; Saito, N; Suzuki, I H; Fukuzawa, H; Liu, X-J; Sakai, K; Pruemper, G; Ueda, K; Iwayama, H; Nagaya, K; Yao, M; Kreidi, K; Schoeffler, M; Jahnke, T; Schoessler, S; Doerner, R; Weber, T; Harries, J; Tamenori, Y

    2008-01-01

    We have identified interatomic Coulombic decay (ICD) processes in the ArKr dimer following Ar 2p Auger decay, using momentum-resolved electron-ion-ion coincidence spectroscopy and simultaneously determining the kinetic energy of the ICD electron and the KER between Ar 2+ and Kr + . We find that the spin-conserved ICD processes in which Ar 2+ (3p -3 3d) 1 P and 3 P decay to Ar 2+ (3p -2 ) 1 D and 3 P, respectively, ionizing the Kr atom, are significantly stronger than the spin-flip ICD processes in which Ar 2+ (3p -3 3d) 1 P and 3 P decay to Ar 2+ (3p -2 ) 3 P and 1 D, respectively

  14. Double-sided electron-beam generator for KrF laser excitation

    International Nuclear Information System (INIS)

    Schlitt, L.; Swingle, J.

    1980-05-01

    Several laser systems excited by electron beam have been identified as candidates for pump sources for laser fusion applications. The electron beam generators required must be compact, reliable and capable of synchronization with other system components. A KrF laser producing a minimum output of 25 J was needed for the RAPIER (Raman Amplifier Pumped by Intensified Excimer Radiation) system. A double-sided electron beam system was designed and constructed specifically for this purpose and has produced > 35 J of KrF output. Each of the two electron beam machines in the system operates with an rms jitter of 0.4 ns and together occupy approx. 3.5 m 2 of floor space. The successful operation of this laser has engendered requests for a description of the engineering details of this system. This document contains a brief description of the design issues and a full set of engineering drawings for this KrF laser amplifier

  15. High-spin lifetime measurements in the N=Z nucleus Kr72

    Science.gov (United States)

    Andreoiu, C.; Svensson, C. E.; Afanasjev, A. V.; Austin, R. A. E.; Carpenter, M. P.; Dashdorj, D.; Finlay, P.; Freeman, S. J.; Garrett, P. E.; Greene, J.; Grinyer, G. F.; Görgen, A.; Hyland, B.; Jenkins, D.; Johnston-Theasby, F.; Joshi, P.; Machiavelli, A. O.; Moore, F.; Mukherjee, G.; Phillips, A. A.; Reviol, W.; Sarantites, D. G.; Schumaker, M. A.; Seweryniak, D.; Smith, M. B.; Valiente-Dobón, J. J.; Wadsworth, R.

    2007-04-01

    High-spin states in the N=Z nucleus Kr72 have been populated in the Ca40(Ca40, 2α)Kr72 fusion-evaporation reaction at a beam energy of 165 MeV using the Gammasphere array for γ-ray detection coupled to the Microball array for charged particle detection. The previously observed bands in Kr72 were extended to an excitation energy of ˜24 MeV and angular momentum of 30ℏ. Using the Doppler shift attenuation method the lifetimes of high-spin states were measured for the first time. Excellent agreement between the results of calculations within the isovector mean field theory and experiment is observed both for rotational and deformation properties. No enhancement of quadrupole deformation expected in the presence of isoscalar t=0 np pairing is observed. Current data do not show any evidence for the existence of the isoscalar np pairing.

  16. 1.5 MeV Kr+ irradiation of polycrystalline Ge

    International Nuclear Information System (INIS)

    Wang, L.M.; Birtcher, R.C.; Rehn, L.E.

    1990-01-01

    This paper reports 1.5 MeV Kr + irradiation of polycrystalline Ge at room temperature, and subsequent annealing carried out with in situ TEM observations. After a Kr + dose of 1.2 x 10 14 ions/cm 2 , Ge in the electron transparent region was completely amorphized. Continuous irradiation of the amorphized Ge resulted in a high density of small cavities. These cavities, first observed after 7 x 10 14 ions/cm 2 with an average diameter of ∼3 nm, grew into large (∼50 nm) irregular-shaped holes, transforming the irradiated Ge into a sponge-like material after 8.5 x 10 15 ions/cm 2 . The crystallization temperature and the morphology of the crystallized Ge after annealing were found to be dependent on the Kr + dose. The sponge-like structure was retained after crystallization at ∼600 degrees C

  17. Independent Yields of Kr Isotopes at Photofission of $^{232}$Th and $^{238}$U

    CERN Document Server

    Gangrsky, Yu P; Zemlyanoi, S G; Maslova, N Yu; Myshinskii, G V; Norov, K S; Penionzhkevich, Yu E; Selesh, O

    2002-01-01

    The yields of the primary fission fragments - Kr isotopes - at the photofission of ^{232}Th and ^{238}U were measured. The experiments were performed at the microtron of FLNR, JINR, with the energy of the accelerated electrons 25 MeV. The methodic of fission fragments transportation by the gas flow through the capillary and condensation of the inert gases in the cryostat at the liquid nitrogen temperature was used. The fission fragments of other elements were stopped by the filter on the entrance of the capillary. The identification of the Kr isotopes was performed using the gamma-spectra of their daughter products. The mass distribution of the Kr isotopes independent yields was obtained and the comparison with yields at the prompt and thermal neutron fission was discussed.

  18. The modified cryogenic adsorption method for the laboratory separation of sup(85)Kr from the atmosphere

    International Nuclear Information System (INIS)

    Wilhelmova, L.; Tomasek, M.; Dvorak, Z.

    1985-01-01

    A method for laboratory separation of sup(85)Kr from the atmosphere based on cryogenic adsorption technique was developed. The physical parameters of the separation equipment were chosen with respect to the properties of scintillation crystal CaFsub(2)(Eu) used as a detector of sup(85)Kr. The apparatus contains dry-ice, silica gel and molecular sieve traps for the removal of Hsub(2)O and COsub(2). The activated charcoal columns are used for concentration and preparation of krypton sample. The separation technique is supplemented by gas-chromatographic determination of total amount of separated krypton. The apparatus enables processing of up to 20 msup(3) of air with the krypton yield about 80%. The relative errors of the determination of the concentration of sup(85)Kr in the air by elaborated method is about 5%. (author)

  19. Use of sup(81m)Kr gas for the measurement of absolute regional lung ventilation

    Energy Technology Data Exchange (ETDEWEB)

    Nosil, J; Bajzer, Z; Spaventi, S [Mladen Stojanovic Clinical Hospital, Zagreb (Yugoslavia). Dept. of Nuclear Medicine and Oncology; Institut Rudjer Boskovic, Zagreb (Yugoslavia))

    1977-02-01

    In this paper a new method of using sup(81m)Kr for the measurement of specific absolute regional lung ventilation is described. Experimental data suitable for the calculation of quantitative regional ventilation are provided using an adequate respiratory system for sup(81m)Kr dosage and a scintillation gamma camera interfaced to a digital computer. A simple mathematical lung model for the inhalation of sup(81m)Kr is used to determine the specific ventilation and the parameters proportional to the ventilation for the whole lung and different lung regions in patients and in healthy subjects. The lung count rate for a given region correlated well with the ventilation of that region. Clinical examples are given and discussed.

  20. Modeling of Jovian Auroral Polar Ion and Proton Precipitation

    Science.gov (United States)

    Houston, S. J.; Ozak, N. O.; Cravens, T.; Schultz, D. R.; Mauk, B.; Haggerty, D. K.; Young, J. T.

    2017-12-01

    Auroral particle precipitation dominates the chemical and physical environment of the upper atmospheres and ionospheres of the outer planets. Precipitation of energetic electrons from the middle magnetosphere is responsible for the main auroral oval at Jupiter, but energetic electron, proton, and ion precipitation take place in the polar caps. At least some of the ion precipitation is associated with soft X-ray emission with about 1 GW of power. Theoretical modeling has demonstrated that the incident sulfur and oxygen ion energies must exceed about 0.5 MeV/nucleon (u) in order to produce the measured X-ray emission. In this work we present a model of the transport of magnetospheric oxygen ions as they precipitate into Jupiter's polar atmosphere. We have revised and updated the hybrid Monte Carlo model originally developed by Ozak et al., 2010 to model the Jovian X-ray aurora. We now simulate a wider range of incident oxygen ion energies (10 keV/u - 5 MeV/u) and update the collision cross-sections to model the ionization of the atmospheric neutrals. The polar cap location of the emission and magnetosphere-ionosphere coupling both indicate the associated field-aligned currents must originate near the magnetopause or perhaps the distant tail. Secondary electrons produced in the upper atmosphere by ion precipitation could be accelerated upward to relativistic energies due to the same field-aligned potentials responsible for the downward ion acceleration. To further explore this, we simulate the effect of the secondary electrons generated from the heavy ion precipitation. We use a two-stream transport model that computes the secondary electron fluxes, their escape from the atmosphere, and characterization of the H2 Lyman-Werner band emission, including a predicted observable spectrum with the associated color ratio. Our model predicts that escaping electrons have an energy range from 1 eV to 6 keV, H2 band emission rates produced are on the order of 75 kR for an input

  1. Acidity of Scandinavian precipitation

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, E; Bordin, G

    1955-01-01

    Data on the pH of the total monthly precipitation at stations of a Swedish network for sampling and chemical analysis of precipitation and atmospheric aerosols during the year July 1953 to June 1954 are presented and discussed, together with the pH data from the first two months of operation of a large pan-Scandinavian net. It is found that well-defined regions of acidity and alkalinity relative to the pH of water in equilibrium with atmospheric carbon dioxide exist, and that these regions persist to such an extent that the monthly deviations from the pattern of the annual mean pH at stations unaffected by local pollution show persistently high acidity, while inland northern stations show equally persistent alkalinity. Some possible reasons for the observed distributions are considered.

  2. Hanford phosphate precipitation filtration process evaluation

    International Nuclear Information System (INIS)

    Walker, B.W.; McCabe, D.J.

    1997-01-01

    The purpose of this filter study was to evaluate cross-flow filtration as effective solid-liquid separation technology for treating Hanford wastes, outline operating conditions for equipment, examine the expected filter flow rates, and determine proper cleaning. A proposed Hanford waste pre-treatment process uses sodium hydroxide at high temperature to remove aluminum from sludge. This process also dissolves phosphates. Upon cooling to 40 degrees centigrade the phosphates form a Na7(PO4)2F9H2O precipitate which must be removed prior to further treatment. Filter studies were conducted with a phosphate slurry simulant to evaluate whether 0.5 micron cross-flow sintered metal Mott filters can separate the phosphate precipitate from the wash solutions. The simulant was recirculated through the filters at room temperature and filtration performance data was collected

  3. Magnetite precipitation and characterisation

    International Nuclear Information System (INIS)

    Joyce, A.; Garside, J.; Ivens, R.

    1988-06-01

    Magnetite (Fe 3 O 4 ) precipitation was investigated as a possible alternative treatment process to the conventional ferric hydroxide for removal of actinides from radioactive effluents. This offered the possibility of improved dewatering of filtered residues. Whilst a poor quality magnetite could be produced from deoxygenated ferrous/ferric solutions, all attempts to prepare magnetite from effluent simulates were unsuccessful. The failure was attributed to the presence of high nitrate and other interfering ions. (author)

  4. All-Optical Atom Trap Trace Analysis: Potential Use of 85Kr in Safeguards Activities

    International Nuclear Information System (INIS)

    Kohler, M.; Sahling, P.; Sieveke, C.; Kirchner, G.

    2015-01-01

    Sensitive measurement techniques for the detection of anthropogenic tracers demand measurement resolutions down to single atoms, as it has been demonstrated by the first atom trap trace analysis experiments. However, technical limitations had lowered the sample throughput to about 200 per year per machine. We have developed an all-optical apparatus which allows higher sample throughput and small sample sizes at the same time. Krypton-85 as anthropogenic isotope is an ideal tracer for nuclear activities since the only relevant source term is fission. An increased 85Kr concentration in an air sample indicates, that a plume was passing by during sampling. In practice, however, its applicability may be limited by the global and regional background concentrations caused by the emissions of nuclear fuel reprocessing plants. The potential of 85Kr monitoring for safeguards applications has been discussed extensively. Among these is the short range detection of elevated concentrations of 85Kr in the vicinity of reprocessing plants. Our ATTA technique needs sample sizes of about 1 l of air only and thus for the first time will allow simple environmental sampling of 85Kr with high spatial and temporal resolution. The design of such a study including local sampling and tracer transport modelling in proximity to a reprocessing plants is outlined. In addition, such a study could be used also for validating near-field atmospheric dispersion models if the 85Kr source term is known. The potential of environmental analyzes of 85Kr during an IAEA short-notice access is discussed. It is shown that it crucially depends on the emission dynamics after shut-down of fuel dissolution which needs further study. (author)

  5. Studies on the decoupled rotation bands in the nuclei 79Rb, 81Rb, and 79Kr

    International Nuclear Information System (INIS)

    Panqueva Alvarez, J.H.

    1982-01-01

    High spin states in 79 Rb, 81 Rb, and 79 Kr were studied by means of the following reactions: 63 Cu( 19 F,p2n) 79 Rb, 70 Ge( 12 C,p2n) 79 Rb, 65 Cu( 16 O,2n) 79 Rb, 65 Cu( 19 F,p2n) 81 Rb, 63 Cu( 19 F,2pn) 79 Kr, and 70 Ge( 12 C,2pn) 79 Kr. On the base of γ single spectra, excitation functions, γ angular distributions, γγ and nγ coincidences, RDDS- and DSA lifetime measurements a level scheme of 79 Rb with 13 new found excited states is proposed. Also a series of stretched E2-transitions between posivite parity states in 79 Kr could be identified. The observed M1 and E2 transition probabilities, which were obtained via the experimental determination of the lifetime as well the branching ratio of 26 excited states, form the base for a comprehensive discussion of the nuclear structure of the studied isotopes. For this reason theoretical calculations with the asymmetric rotor-plus-quasiparticle with variable moment of inertia (AROVMI) as well with the interacting boson-fermion (IBVM) model were performed. The good agreement between experiment and theory permits to relate the decrease of the B(E2)-values in 79 Rb to a finite dimensional (N=8) boson space, to cancel the discrepancies stated by Friederichs et.al., and to analyze 79 Kr the influence of a gsub(9/2) neutron on the deformation of the 78 Kr core. (orig./HSI) [de

  6. Qualitative risk assessment for the 100-KR-4 groundwater operable unit

    Energy Technology Data Exchange (ETDEWEB)

    Biggerstaff, R.L.

    1994-06-30

    This report provides the qualitative risk assessment (QRA) for the 100-KR-4 groundwater operable unit at the US Department of Energy`s (DOE) Hanford Site in southeastern Washington State. The extent of the groundwater beneath the 100 K Area is defined in the Remedial Investigation/Feasibility Study Work Plan for the 100-KR-4 Operable Unit (DOE-RL 1992a). The QRA is an evaluation or risk using a limited amount of data and a predefined set of human and environmental exposure scenarios and is not intended to replace or be a substitute for a baseline risk assessment.

  7. Scaling and development of KrF laser for fusion driver

    International Nuclear Information System (INIS)

    Owadano, Y.; Okuda, I.; Matsumoto, Y.; Matsushima, I.; Tomie, T.; Miura, E.; Yashiro, E.

    1994-01-01

    A conceptual design of a 1 MJ KrF laser ICF driver is presented. The design is based on a heavily saturated high gain amplifier which gives high efficiency, high stage gain and enough ASE suppression at the same time. The system consists of 16 modules of 1.5m square aperture final amplifier (260ns gain duration), 2 pre-amplifiers and 32 time angular multiplexing optical system for pulse compression. Development of a 10kJ-class KrF laser at Electrotechnical Laboratory (ETL) is also described. (author)

  8. Improvements in the equipment for determination of Kr-85 with the reference method

    International Nuclear Information System (INIS)

    Heras Iniquez, M.C.; Perez Garcia, M.M.

    1983-01-01

    A new equipment for Kr-85 separation and their cryogenic chromatographic concentration is described, which presents some advantages respect the equipment used as reference. The new apparatus, made with metallic elements, is based on the method of concentration and separation previously described but presents easier control, faster chromatographic separations and without loosed of efficiency and reproducibility that the previous one. The concentration and separation procedure for Kr-85 and a comparative study between both apparatus is described. Also the efficiency of the method is obtained experimentally. (Author)

  9. Results of a search for double positron decay and electron-positron conversion of 78Kr

    International Nuclear Information System (INIS)

    Saenz, C.; Cerezo, E.; Garcia, E.; Morales, A.; Morales, J.; Nunez-Lagos, R.; Ortiz de Solorzano, A.; Puimedon, J.; Salinas, A.; Sarsa, M.L.; Villar, J.A.; Klimenko, A.; Kuzminov, V.; Metlinsky, N.; Novikov, V.; Pomansky, A.; Pritychenko, B.

    1994-01-01

    The results of a search for the 2β + and Kβ + decay modes of 78 Kr, in a coincidence experiment using a high pressure ionization chamber of enriched 78 Kr inside an array of sodium iodine scintillators, are presented. After 4434 h of counting time, the half-life lower limits obtained are T 1/2 (Kβ + ) 0ν ≥5.1x10 21 yr and T 1/2 (2β + ) 0ν+2ν ≥2.0x10 21 yr at 68% C.L

  10. Interference effects in Auger spectra at the 3d9np resonances in Kr

    International Nuclear Information System (INIS)

    Lagutin, B M; Demekhin, Ph V; Sukhorukov, V L; Ehresmann, A; Schmoranzer, H

    2003-01-01

    Absolute photoionization cross sections for the population of the Kr II 4p 4 np states when the exciting-photon energy corresponds to the first four 3d 9 np resonances were calculated beyond the two-step model for the first time. Good agreement between computed and measured photoionization cross sections proves the importance of taking into account the interference between different resonance channels in understanding the dynamics of the Auger decay of the Kr I 3d 9 np resonances. (letter to the editor)

  11. Feasibility of a 81Br(ν,e-) 81Kr solar neutrino experiment

    International Nuclear Information System (INIS)

    Hurst, G.S.; Chen, C.H.; Kramer, S.D.; Cleveland, B.T.; Davis, R. Jr.; Rowley, R.K.; Gabbard, F.; Schima, F.J.

    1984-01-01

    A solar neutrino experiment utilizing the interaction of 81 Br(ν,e - ) 81 Kr to study the 7 Be neutrino source in the interior of the sun is shown to be feasible. Resonance ionization spectroscopy was used to count less than 1000 atoms of 2 x 10 5 -yr 81 Kr, making the bromine experiment possible. Except for the method of counting product atoms, the bromine experiment would be very similar to the successful chlorine detector 37 Cl(ν,e - ) 37 Ar, and thus it is a natural sequel to the only solar neutrino experiment to date

  12. Proposed solar neutrino experiment using 81Br(nu,e-)81Kr

    International Nuclear Information System (INIS)

    Hurst, G.S.; Chen, C.H.; Kramer, S.D.; Allman, S.L.

    1984-12-01

    It has now been shown that it is feasible to measure the 7 Be neutrino source in the sun by using the reaction 81 Br(nu,e - ) 81 Kr in a radiochemical experiment. Such an experiment would be quite similar to the Davis, Cleveland, and Rowley method for measuring the 8 B neutrino using 37 Cl(nu,e - ) 37 Ar except that the resonance ionization spectroscopy (RIS) method (instead of decay counting) would be employed to count the 2 x 10 5 -yr 81 Kr atoms

  13. Core drilling of deep drillhole OL-KR57 at Olkiluoto in Eurajoki 2011-2012

    Energy Technology Data Exchange (ETDEWEB)

    Toropainen, V. [Suomen Malmi Oy, Espoo (Finland)

    2012-07-15

    As a part of the confirming site investigations at Olkiluoto, Suomen Malmi Oy (Smoy) core drilled 401.71 m and 45.01 m deep drillholes, OL-KR57 and OL-KR57B, at Olkiluoto in September 2011 - January 2012. The diameter of the drillholes is 75.7 mm. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the returning and drilling water were recorded. The drill rig was computer controlled and the computer recorded drilling parameters during drilling. The objective of the measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling, flushing and washing water were 350 m3 and 30 m3 in the drillholes OL-KR57 and OL-KR57B, respectively. The measured volumes of the returning water in the drillholes were 328 m{sup 3} and 16.8 m{sup 3}, respectively. The deviations of the drillholes were measured with the deviation measuring instruments EMS and Gyro. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive strength was 123.9 MPa, the average Young's Modulus was 42.6 GPa and the average Poisson's ratio was 0.23. The main rock types are veined and diatexitic gneisses, mica gneiss and tonaliticgranodioritic- granitic gneiss. The average fracture frequency is 2.5 pcs/m in drillhole OL-KR57 and 3.3 pcs/m in the drillhole OL-KR57B. The average RQD values are 95.0 % and 93.0 %. Seven separate fractured zones were interpreted from OL-KR57 and three fractured zones from OL-KR57B. (orig.)

  14. Application of the boson expansion theory to Se and Kr isotopes

    International Nuclear Information System (INIS)

    Pedrocchi, V.G.; Tamura, T.

    1988-01-01

    The boson expansion theory is applied to even Se and Kr isotopes with neutron number N = 38-48. Energy spectra, B(E2) values and quadrupole moments are calculated and fairly good agreement with experimental data is obtained. The coupling of collective quadrupole and monopole pairing vibrational modes is also included in order to fit low-lying O 2 + states in some of the nuclei. The calculated values of the quadrupole moments indicate that both Se and Kr nuclei are in a transitional region from a prolate to an oblate shape. (author)

  15. Qualitative risk assessment for the 100-KR-4 groundwater operable unit

    International Nuclear Information System (INIS)

    Biggerstaff, R.L.

    1994-01-01

    This report provides the qualitative risk assessment (QRA) for the 100-KR-4 groundwater operable unit at the US Department of Energy's (DOE) Hanford Site in southeastern Washington State. The extent of the groundwater beneath the 100 K Area is defined in the Remedial Investigation/Feasibility Study Work Plan for the 100-KR-4 Operable Unit (DOE-RL 1992a). The QRA is an evaluation or risk using a limited amount of data and a predefined set of human and environmental exposure scenarios and is not intended to replace or be a substitute for a baseline risk assessment

  16. β Decay in the Region of Neutron-deficient {sup 69,70,71}Kr

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, A.M., E-mail: ARogers@lbl.gov [Physics Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Lawrence Berkeley National Laboratory, Berkeley, CA, 94720 (United States); Giovinazzo, J. [Centre d' Etudes Nucléaires de Bordeaux-Gradignan, Université Bordeaux 1, UMR 5797 CNRS/IN2P3, Chemin du Solarium, BP 120, F-33175, Gardignan Cedex (France); Lister, C.J. [Physics Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Blank, B.; Canchel, G. [Centre d' Etudes Nucléaires de Bordeaux-Gradignan, Université Bordeaux 1, UMR 5797 CNRS/IN2P3, Chemin du Solarium, BP 120, F-33175, Gardignan Cedex (France); Clark, J.A. [Physics Division, Argonne National Laboratory, Argonne, IL 60439 (United States); France, G. de; Grévy, S. [GANIL CEA/DSM-CNRS/IN2P3, Boulevard Henri Becquerel, BP55027, 14076 CEAN Cedex 5 (France); Gros, S.; McCutchan, E.A. [Physics Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Oliveira Santos, F. de [GANIL CEA/DSM-CNRS/IN2P3, Boulevard Henri Becquerel, BP55027, 14076 CEAN Cedex 5 (France); Savard, G.; Seweryniak, D. [Physics Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Stefan, I.; Thomas, J.-C. [GANIL CEA/DSM-CNRS/IN2P3, Boulevard Henri Becquerel, BP55027, 14076 CEAN Cedex 5 (France)

    2014-06-15

    Decay spectroscopy was performed for neutron-deficient nuclei ranging from zinc to krypton with isospin −3/2 ≤T{sub z}≤0. Measurements of correlated β-delayed protons allowed us to determine the isobaric analog states fed from the decay of {sup 65}Se and {sup 69}Kr, constraining the spin of the {sup 69}Kr ground state. Preliminary results regarding the half lives for the T{sub z}=−1 systems, relevant to the rapid proton capture (rp) process, are discussed.

  17. Results of a search for double positron decay and electron-positron conversion of 78Kr

    International Nuclear Information System (INIS)

    Saenz, C.; Garcia, E.; Klimenko, A.; Kuzminov, V.; Metlinsky, N.; Morales, A.; Morales, J.; Novikov, V.; Nunez-Lagos, R.; Ortiz de Solorzano, A.; Pomansky, A.; Pritytchenko, V.; Puimedon, J.; Salinas, A.; Sarsa, M.L.; Villar, J.A.

    1994-01-01

    The results of a search for the 2β + and Kβ + decay modes of 78 Kr, in a coincidence experiment using a high pressure ionization chamber of enriched 78 Kr inside an enceinte of sodium iodine scintillators, are presented. After 4434 hours of counting time, the half-life lower limits obtained are T 1/2 (Kβ + ) 0ν ≥qslant5.8x10 21 y and T 1/2 (2β + ) 0ν+2ν ≥qslant2.0x10 21 y at 68%C.L. ((orig.))

  18. Solar-wind krypton and solid/gas fractionation in the early solar nebula

    Science.gov (United States)

    Wiens, Roger C.; Burnett, D. S.; Neugebauer, M.; Pepin, R. O.

    1991-01-01

    The solar-system Kr abundance is calculated from solar-wind noble-gas ratios, determined previously by low-temperature oxidations of lunar ilmenite grains, normalized to Si by spacecraft solar-wind measurements. The estimated Kr-83 abundance of 4.1 + or - 1.5 per million Si atoms is within uncertainty of estimates assuming no fractionation, determined from CI-chondrite abundances of surrounding elements. This is significant because it is the first such constraint on solid/gas fractionation, though the large uncertainty only confines it to somewhat less than a factor of two.

  19. Precipitation in partially stabilized zirconia

    International Nuclear Information System (INIS)

    Bansal, G.K.

    1975-01-01

    Transmission electron microscopy was used to study the substructure of partially stabilized ZrO 2 (PSZ) samples, i.e., 2-phase systems containing both cubic and monoclinic modifications of zirconia, after various heat treatments. Monoclinic ZrO 2 exists as (1) isolated grains within the polycrystalline aggregate (a grain- boundary phase) and (2) small plate-like particles within cubic grains. These intragranular precipitates are believed to contribute to the useful properties of PSZ via a form of precipitation hardening. These precipitates initially form as tetragonal ZrO 2 , with a habit plane parallel to the brace 100 brace matrix planes. The orientation relations between the tetragonal precipitates and the cubic matrix are brace 100 brace/sub matrix/ 2 parallel brace 100 brace /sub precipitate/ or (001)/sub precipitate/ and broken bracket 100 broken bracket/sub matrix/ 2 parallel broken bracket 100 broken bracket/sub precipitate/ or [001]/sub precipitate/. (U.S.)

  20. Hourly Precipitation Data (HPD) Publication

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Hourly Precipitation Data (HPD) Publication is archived and available from the National Climatic Data Center (NCDC). This publication contains hourly precipitation...

  1. Effect of precipitation on internal friction of AZ91 magnesium alloy

    Institute of Scientific and Technical Information of China (English)

    刘树伟; 姜海昌; 李秀艳; 戎利建

    2010-01-01

    The effect of precipitation on the internal friction(IF)of AZ91 magnesium alloy was investigated by using X-ray diffraction(XRD)analysis,scanning electron microscope(SEM)observation,and dynamic mechanical analysis(DMA).Six different states of alloy were prepared by applying different heat treatment processes:as-cast,in-complete solid solution,complete solid solution,micro-precipitation,continuous precipitation and continuous-discontinuous precipitation.It was found that the internal friction of in-completely solid-solutionized,completely solid-solutionized and micro-precipitated specimens showed a similar characteristic,and the grain boundary relaxation is completed depressed due to the Al atoms supersaturated in theα-Mg solution.However,a thermal relaxation internal friction peak was observed for continuously precipitated and continuously-discontinuously precipitated specimens at around 438 K and frequency of about 1 Hz,which was attributed to the grain boundaries relaxation.Furthermore,it was found that the relaxation of theβ-Mg17Al12/α-Mg phase interfaces should give its contribution to the background internal friction in the as-cast,continuously precipitated and continuously-discontinuously precipitated specimens.

  2. Staranje cevi uparjalnikov v Jedrski elektrarni Krško: Aging of tubes in the Krško nuclear power plant's steam generators:

    OpenAIRE

    Androjna, Ferdo; Cizelj, Leon

    2000-01-01

    The paper reviews the domestic efforts devoted to the safe and reliable operation of the Krško nuclear power plant (NPP) at full power, close to the design limit of the steam generators (18% of plugged tubes) for a full decade. This includes an overview of the recent status and history of the degradation processes, discussion of repair criteria, defining the acceptable size of defects and selected results from safety analyses supporting the operation of degraded steam generator (SG) tubes. It...

  3. Design criteria and design basis for the 100-HR-3 and 100-KR-4 pump-and-treat projects

    International Nuclear Information System (INIS)

    McKinley, W.S.; Winters, J.N.

    1996-06-01

    The 100-HR-3 and 100-KR-4 Operable Units are located in the 100 Area at the Hanford Site in Richland, Washington. The document describes the project objectives and design criteria to be used for the 100-HR-3 and 100-KR-4 groundwater pump-and-treat design activities

  4. Growth rate of dislocation loop in Fe-Ni-Cr alloy under Kr+ ion and electron irradiation

    International Nuclear Information System (INIS)

    Kimoto, T.; Allen, C.W.; Rehn, L.E.

    1991-10-01

    In order to examine the effect of irradiating particle species on the growth rate of radiation-induced dislocation loops, a solution-annealed Fe-25Ni-15Cr-0.02C alloy was irradiated at 723 K first by 1.5 MeV Kr + ions for 2520 sec, then by 1.5 MeV Kr + ions and 1.0 MeV electrons simultaneously for 780 sec, and finally by 1.0 MeV electrons for 780 sec with the HVEM-Tandem Facility in Argonne National Laboratory. The calculated damage rate by 1.5 MeV Kr + ions was 5.8 x 10 -4 dpa/s, and that by 1.0 MeV electrons was 1 x 10 -4 dpa/s. The growth rate of a dislocation loop located at the center of the specimen was 7 x 10 -3 nm/s for the Kr + ion irradiation, 4 x 10 -2 nm/s for the simultaneous Kr + and electron irradiation, and (2--3) x 10 -2 nm/s for the electron irradiation. This implies that the electron irradiation is about 19 times more effective in the growth of radiation-induced dislocation loops than the Kr + ion irradiation. The dislocation loop growth rate under the simultaneous Kr + and electron irradiation is higher than the sum of the growth rates under the individual Kr + and electron irradiations. 5 refs., 4 figs

  5. The Effectiveness of Local Culture-Based Mathematical Heuristic-KR Learning towards Enhancing Student's Creative Thinking Skill

    Science.gov (United States)

    Tandiseru, Selvi Rajuaty

    2015-01-01

    The problem in this research is the lack of creative thinking skills of students. One of the learning models that is expected to enhance student's creative thinking skill is the local culture-based mathematical heuristic-KR learning model (LC-BMHLM). Heuristic-KR is a learning model which was introduced by Krulik and Rudnick (1995) that is the…

  6. Feasibility of evaluating possible sup 85 Kr environmental contamination from neon lamp production line to be installed

    Energy Technology Data Exchange (ETDEWEB)

    Guangzuo, Li [Chengdu Sanitary-Epidemiological Station, Chengdu, SC (China)

    1989-12-01

    Using a simplified method, the concentrations of {sup 85}Kr leaking into the air of a workshop and its surroundings, where a neon lamp production line was to be installed, were calculated. The doses to the workers and inhabitants nearby were also estimated. Thus, the evaluation of {sup 85}Kr enviromental contamination caused by imported equipments was made feasible.

  7. Precipitation Indices Low Countries

    Science.gov (United States)

    van Engelen, A. F. V.; Ynsen, F.; Buisman, J.; van der Schrier, G.

    2009-09-01

    Since 1995, KNMI published a series of books(1), presenting an annual reconstruction of weather and climate in the Low Countries, covering the period AD 763-present, or roughly, the last millennium. The reconstructions are based on the interpretation of documentary sources predominantly and comparison with other proxies and instrumental observations. The series also comprises a number of classifications. Amongst them annual classifications for winter and summer temperature and for winter and summer dryness-wetness. The classification of temperature have been reworked into peer reviewed (2) series (AD 1000-present) of seasonal temperatures and temperature indices, the so called LCT (Low Countries Temperature) series, now incorporated in the Millennium databases. Recently we started a study to convert the dryness-wetness classifications into a series of precipitation; the so called LCP (Low Countries Precipitation) series. A brief outline is given here of the applied methodology and preliminary results. The WMO definition for meteorological drought has been followed being that a period is called wet respectively dry when the amount of precipitation is considerable more respectively less than usual (normal). To gain a more quantitative insight for four locations, geographically spread over the Low Countries area (De Bilt, Vlissingen, Maastricht and Uccle), we analysed the statistics of daily precipitation series, covering the period 1900-present. This brought us to the following definition, valid for the Low Countries: A period is considered as (very) dry respectively (very) wet if over a continuous period of at least 60 days (~two months) cq 90 days (~three months) on at least two out of the four locations 50% less resp. 50% more than the normal amount for the location (based on the 1961-1990 normal period) has been measured. This results into the following classification into five drought classes hat could be applied to non instrumental observations: Very wet period

  8. Excess Gibbs energy for six binary solid solutions of molecularly simple substances

    Energy Technology Data Exchange (ETDEWEB)

    Lobo, L J; Staveley, L A.K.

    1985-01-01

    In this paper we apply the method developed in a previous study of Ar + CH/sub 4/ to the evaluation of the excess Gibbs energy G /SUP E.S/ for solid solutions of two molecularly simple components. The method depends on combining information on the excess Gibbs energy G /SUP E.L/ for the liquid mixture of the two components with a knowledge of the (T, x) solid-liquid phase diagram. Certain thermal properties o the pure substances are also needed. G /SUP E.S/ has been calculated for binary mixtures of Ar + Kr, Kr + CH/sub 4/, CO + N/sub 2/, Kr + Xe, Ar + N/sub 2/, and Ar + CO. In general, but not always, the solid mixtures are more non-ideal than the liquid mixtures of the same composition at the same temperature. Except for the Kr + CH/sub 4/ system, the ratio r = G /SUP E.S/ /G /SUP E.L/ is larger the richer the solution in the component with the smaller molecules.

  9. The removal of sulphate from mine water by precipitation as ettringite and the utilisation of the precipitate as a sorbent for arsenate removal.

    Science.gov (United States)

    Tolonen, Emma-Tuulia; Hu, Tao; Rämö, Jaakko; Lassi, Ulla

    2016-10-01

    The aim of this research was to investigate sulphate removal from mine water by precipitation as ettringite (Ca6Al2(SO4)3(OH)12·26H2O) and the utilisation of the precipitate as a sorbent for arsenate removal. The mine water sulphate concentration was reduced by 85-90% from the initial 1400 mg/L during ettringite precipitation depending on the treatment method. The precipitation conditions were also simulated with MINEQL + software, and the computational results were compared with the experimental results. The precipitated solids were characterised with X-ray diffraction and a scanning electron microscope. The precipitated solids were tested as sorbents for arsenate removal from the model solution. The arsenic(V) model solution concentration reduced 86-96% from the initial 1.5 mg/L with a 1 g/L sorbent dosage. The effect of initial arsenate concentration on the sorption of arsenate on the precipitate was studied and Langmuir, Freundlich, and Langmuir-Freundlich sorption isotherm models were fitted to the experimental data. The maximum arsenate sorption capacity (qm = 11.2 ± 4.7 mg/g) of the precipitate was obtained from the Langmuir-Freundlich isotherm. The results indicate that the precipitate produced during sulphate removal from mine water by precipitation as ettringite could be further used as a sorbent for arsenate removal. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Dissolution of heavy metals from electrostatic precipitator (ESP) dust ...

    African Journals Online (AJOL)

    Coal based sponge iron industries in India generate considerable quantity of solid waste, 40% of which is flue dust produced from the electrostatic precipitator (ESP) connected to rotary kiln. This paper reports the dissolution of Zn, Cu, Pb, Mn and Fe from the ESP dust using three fungal species, Aspergillus niger, ...

  11. Precipitation of plutonium from acidic solutions using magnesium oxide

    International Nuclear Information System (INIS)

    Jones, S.A.

    1994-01-01

    Magnesium oxide will be used as a neutralizing agent for acidic plutonium-containing solutions. It is expected that as the magnesium oxide dissolves, the pH of the solution will rise, and plutonium will precipitate. The resulting solid will be tested for suitability to storage. The liquid is expected to contain plutonium levels that meet disposal limit requirements

  12. Laser Plasma Instability (LPI) Driven Light Scattering Measurements with 44 beam-lines of Nike KrF Laser^*

    Science.gov (United States)

    Oh, J.; Weaver, J. L.; Kehne, D. M.; Phillips, L. S.; Obenschain, S. P.; Serlin, V.; McLean, E. A.; Lehmberg, R. H.; Manka, C. K.

    2009-11-01

    With short wavelength (248 nm), large bandwidth (˜1 THz), and ISI beam smoothing, Nike KrF laser provides unique opportunities of LPI research for direct-drive inertial confinement fusion. Previous experiments at intensities (10^15˜10^16 W/cm^2) exceeded two-plasmon decay (TPD) instability threshold using 12 beam-lines of Nike laser.^a,b For further experiments to study LPI excitation in bigger plasma volumes, 44 Nike main beams have been used to produce plasmas with total laser energies up to 1 kJ of ˜350 psec FWHM pulses. This talk will present results of the recent LPI experiment focusing on light emission data in spectral ranges relevant to the Raman (SRS) and TPD instabilities. The primary diagnostics were time-resolved spectrometers with an absolute-intensity-calibrated photodiode array in (0.4˜0.8)φ0 and a streak camera near 0.5φ0. Blackbody temperature and expansion speed measurements of the plasmas were also made. The experiment was conducted at laser intensities of (1˜4)x10^15 W/cm^2 on solid planar CH targets. ^a J. L. Weaver, et al, NO4.14, APS DPP (2008) ^b J. Oh, et al, NO4.15, APS DPP (2008) * Work supported by DoE/NNSA and performed at Naval Research Laboratory.

  13. Melnās krāsas iespējas interjerā

    OpenAIRE

    Lapkovska, Ērika

    2016-01-01

    Diplomdarbā “Melnās krāsas iespējas interjerā”, analizējot pieejamo literatūru, tiek apskatīta melnās krāsas izpratne, nozīme un lietojums vēsturiskā skatījumā, kā arī melnās krāsas izmantojuma principi interjerā. Empīriskajā daļā tiek veikts salīdzinošais pētījums, analizējot dažādus kafejnīcu un bāru interjerus Latvijā un pasaulē, kuros ir melnās krāsas klātbūtne. Diplomdarba apjoms – 75 lpp., kurās iekļauts ievads, 4 nodaļas, 7 apakšnodaļas, literatūras saraksts ar 53 vienībām, 2 pielikum...

  14. Powerful highly efficient KrF lamps excited by surface and barrier discharges

    International Nuclear Information System (INIS)

    Borisov, V M; Vodchits, V A; El'tsov, A V; Khristoforov, O B

    1998-01-01

    An investigation was made of the characteristics of KrF lamps with different types of excitation by surface and barrier discharges in which the dielectric material was sapphire. The conditions were determined for the attainment of an extremely high yield of the KrF* fluorescence with the internal efficiency η in ∼30 % and 22% for pulsed surface and barrier discharges, respectively. A homogeneous surface discharge was maintained without gas circulation when the pulse repetition rate was 5 x 10 4 Hz. Quasicontinuous excitation of a surface discharge at near-atmospheric pressure made it possible to reach a KrF* fluorescence power density of about 80 W cm -3 , which was close to the limit set by the kinetics of the gaseous medium. Under prolonged excitation conditions the intensity of the UV output radiation was limited by the permissible heating of the gas to a temperature above which the operating life of the gaseous mixture containing fluorine fell steeply. This was the reason for the advantage of surface over barrier discharges: the former were characterised by a high thermal conductivity of a thin (∼0.2 mm) plasma layer on the surface of the cooled dielectric, which made it possible to construct powerful highly efficient KrF and ArF lamps emitting UV radiation of up to 1 W cm -2 intensity. (laser system components)

  15. KrF laser amplifier with phase-conjugate Brillouin retroreflectors.

    Science.gov (United States)

    Gower, M C

    1982-09-01

    We have demonstrated the use of phase-conjugate stimulated Brillouin scattering mirrors to produce high-quality, short-pulse KrF laser beams from angular multiplexed and regenerative amplifiers. The mirror was also shown to isolate systems optically from amplifier spontaneous emission. Automatic alignment of targets using this mirror as a retroreflector was also demonstrated.

  16. Conceptual design of a hybrid KrF laser system for ICF commercial applications

    International Nuclear Information System (INIS)

    Harris, D.B.; Lowenthal, D.D.

    1986-01-01

    KrF lasers appear to be the most efficient lasers operating near the optimal wavelength for laser fusion. Most high-efficiency, low-cost KrF laser designs use large electron-beam-driven amplifiers and use pure angular multiplexing for the required pulse compression. A recent study carried out by Los Alamos National Lab. and Spectra Technology has defied a high-efficiency hybrid KrF laser system architecture that uses both angular multiplexing and Raman beam combination. The high overall system efficiency of this hybrid design, ∼ 12%, is achieved primarily through the use of electron-beam sustained discharge lasers (EBSDL), and by using the efficient forward rotational Raman process in hydrogen. The new system appears attractive as a commercial-applications driver because the calculated efficiency is higher than the usual large electron-beam-pumped (EBP) KrF laser/pure angular multiplexing approach. In this paper, the hybrid system architecture will be described, and the trade-offs with respect to the large EBP amplifier/angular multiplexed system will be discussed

  17. Conceptual design of a hybrid KrF laser system for ICF commercial applications

    International Nuclear Information System (INIS)

    Harris, D.B.; Lowenthal, D.D.

    1986-01-01

    KrF lasers appear to be the most efficient lasers operating near the optimal wavelength for laser fusion. Most high-efficiency, low-cost KrF laser designs use large electron-beam driven amplifiers and use pure angular multiplexing for the required pulse compression. A recent study carried out by Los Alamos and Spectra Technology has defined a high-efficiency hybrid KrF laser system architecture that uses both angular multiplexing and Raman beam combination. The high overall system efficiency of this hybrid design, approximately 12%, is achieved primarily through the use of e-beam sustained discharge lasers (EBSDL), and by using the efficient forward rotational Raman process in hydrogen. The new system appears attractive as a commercial-applications driver because the calculated efficiency is higher than the usual large e-beam pumped (EBP) KrF laser/pure angular multiplexing approach. In this paper, the hybrid system architecture is described, and the tradeoffs with respect to the large EBP amplifier/angular multiplexed system are discussed

  18. Production of 41Ar and 79Kr gaseous radiotracers for industrial applications

    International Nuclear Information System (INIS)

    Yelgaonkar, V.N.; Jagadeesan, K.C.; Shivarudrappa, V.; Sharma, V.K.; Chitra, S.

    2007-01-01

    Radiotracers are extensively used in many industries for trouble shooting and optimization of process parameters leading to considerable savings in time and huge economic benefits. In chemical and petrochemical industries different gases and vapours flowing in the conversion reactors play a major role in the final production. Gaseous radiotracers are ideal to study hydrodynamics of gas phases in process vessels. 41 Ar and 79 Kr are the preferred gaseous radiotracers for such studies. Owing to the increase in demand from Indian industries for gas phase radiotracers, efforts have been made to produce 41 Ar and 79 Kr indigenously by irradiation of 40 Ar and enriched 78 Kr gaseous targets in research reactors. Prequalification of the containers used, safety aspects concerning accidental rupture and mandatory tests necessary for irradiation of gaseous targets in the reactors have been studied. The paper describes some of the important safety aspects involved and the results of trial irradiations on the production of 41 Ar and 79 Kr radiotracers. Standardization of suitable assay protocols for their regular production and supply for applications in industries is also described. (author)

  19. Mitigation action plan for the 100-HR-3 and 100-KR-4 pump and treat project

    International Nuclear Information System (INIS)

    1996-11-01

    This project involves drilling 22 wells, improving access roads to existing and new wells, laying connecting pipes, and constructing groundwater treatment facilities in the 100-KR-4 Area and 100-HR-3 Operable Units. Drilling is expected to be completed by September 1996, but the treatment operations will continue for approximately 10 years

  20. Coulomb excitation of $^{94,96}$Kr beam Deformation in the neutron-rich krypton isotopes

    CERN Multimedia

    Hass, M; Cederkall, J A; Di julio, D D; Zamfir, N - V; Srebrny, J; Wadsworth, R; Siem, S; Marginean, R; Iwanicki, J S

    Recently the energy of the 2$_{1}^{+}$ state in the N=60 $^{96}$Kr nucleus was determinated to be 241 keV. This was the first experimental observation of an excited state in this highly exotic nucleus. The 2$_{1}^{+}$ state in $^{94}$Kr is located at 665.5 keV, i.e. E(2$_{1}^{+}$) drops by more than 400 keV at N=60. This lowering of the 2$_{1}^{+}$ energy indicates a sharp shape transition behavior which is somewhat similar to that discovered in the Sr and Zr isotopic chains at N=60. The deformation expected for the 2$_{1}^{+}$ state of $^{96}$Kr, as resulting from the E(2$_{1}^{+}$) energy based on the semi-empirical relation of Raman et al. is $\\beta_{2}$ = 0.31, which is, however, considerably smaller than that for Sr and Zr ($\\geq$0.40). The sudden decrease of E(2$_{1}^{+}$) from N=50 to N=60 does not fully agree with the more gradual change of deformation deduced from laser spectroscopy measurements of mean square charge radii, although for $^{96}$Kr, in particular, these are consistent with a $\\beta_{2}...

  1. Coulomb Excitation of a Neutron-Rich $^{88}$Kr Beam Search for Mixed Symmetry States

    CERN Multimedia

    Andreoiu, C; Napiorkowski, P J; Iwanicki, J S

    2002-01-01

    We propose to use the ISOLDE/REX/MINIBALL/CD set-up to perform a Coulomb Excitation experiment with a $^{88}$Kr radioactive beam. The motivation includes a search for $Mixed$ $Symmetry$ states predicted by the IBM-2 model, gathering more spectroscopy data about the $^{88}$Kr nucleus and extending shape coexistence studies (performed previously by the proposers for neutron-deficient Kr isotopes) to the neutron-rich side. The proposed experiment will provide data complementary to the Coulomb Excitation of a relativistic $^{88}$Kr beam proposed by D. Tonev et al. for a RISING experiment. A total of 12 days of beam time is necessary for the experiment, equally divided into two runs. One run with a 2.2 MeV/A beam energy on a $^{48}$Ti target and a second run with the maximum available REX energy of 3.1 MeV/A on a $^{208}$Pb target are requested. Using either a UC$_{x}$ or ThC$_{x}$ fissioning primary target coupled with a plasma source by a cooled transfer line seems to be the best choice for the proposed experime...

  2. Clinical evaluation of Kr-81m inhalation study through a dead space

    International Nuclear Information System (INIS)

    Kurosawa, Hiromi; Matsubayashi, Satsuki; Ishii, Yasuko; Ishida, Hirohide; Hirasawa, Yukinori; Mori, Yutaka; Shimada, Takao; Kawakami, Kenji

    1990-01-01

    A new inhalation technique of 81m Kr gas was applied to evaluate the pathophysiological abnormality of ventilation. 81m Kr gas (370 MBq) was continuously supplied into a mouth piece directly (without dead space), V E , or through a dead space of 500 ml, V L , in 110 subjects with various lung diseases. Subjects were divided in four groups by a combination of distribution patterns of 81m Kr gas obtained by these two inhalation techniques. Group 1: No ventilatory defect in both techniques. Group 2: Defects larger in V E than V L . Group 3: Defects larger in V L than V E . Group 4: no remarkable difference in defects in both techniques. Cases of group 1 were normal in pulmonary function test and chest X-ray. Finding of group 2 reflects early airway closure. This group consisted of cases in remission of bronchial asthma, small air way disease and pulmonary congestion. In group 3, restrictive disease and obstructive disease, especially emphysema, were included. Patients with severe obstructive disease and organized change of pulmonary parenchyma were belonged in group 4. In ventilation study with 81m Kr gas, a combined study of inhalation technique through a dead space and by direct infusion may be useful to evaluate a pathophysiological change of various pulmonary diseases. (author)

  3. Repetitively pulsed, high energy KrF lasers for inertial fusion energy

    International Nuclear Information System (INIS)

    Myers, M.C.; Sethian, J.D.; Giuliani, J.L.; Lehmberg, R.; Kepple, P.; Wolford, M.F.; Hegeler, F.; Friedman, M.; Jones, T.C.; Swanekamp, S.B.; Weidenheimer, D.; Rose, D.

    2004-01-01

    Krypton fluoride (KrF) lasers produce highly uniform beams at 248 nm, allow the capability of 'zooming' the spot size to follow an imploding pellet, naturally assume a modular architecture and have been developed into a pulsed-power- based industrial technology that readily scales to a fusion power plant sized system. There are two main challenges for the fusion power plant application: to develop a system with an overall efficiency of greater than 6% (based on target gains of 100) and to achieve a durability of greater than 3 x 10 8 shots (two years at 5 Hz). These two issues are being addressed with the Electra (700 J, 5 Hz) and Nike (3000 J, single shot) KrF lasers at the Naval Research Laboratory. Based on recent advances in pulsed power, electron beam generation and transport, hibachi (foil support structure) design and KrF physics, wall plug efficiencies of greater than 7% should be achievable. Moreover, recent experiments show that it may be possible to realize long lived electron beam diodes using ceramic honeycomb cathodes and anode foils that are convectively cooled by periodically deflecting the laser gas. This paper is a summary of the progress in the development of the critical KrF technologies for laser fusion energy. (author)

  4. High energy extraction of electron beam pumped KrF lasers at multi atmospheres

    NARCIS (Netherlands)

    Kleikamp, B.M.H.H.; Witteman, W.J.

    1984-01-01

    The construction is described of a simple and compact KrF laser with electron beam excitation. The electron beam is generated in a coaxial vacuum diode, driven directly by a ten-stage coaxial Marx generator. A flat MgF2 outcoupler and a suprasil roof prism, protected by an MgF2 window, proved to be

  5. Recent laser experiments on the Aurora KrF/ICF laser system

    International Nuclear Information System (INIS)

    Turner, T.P.; Jones, J.E.; Czuchlewski, S.J.; Watt, R.G.; Thomas, S.J.; Kang, M.; Tallman, C.R.; Mack, J.M.; Figueira, J.F.

    1990-01-01

    The Aurora KrF/ICF Laser Facility at Los Alamos is operational at the kilojoule-level for both laser and target experiments. We report on recent laser experiments on the system and resulting system improvements. 3 refs., 4 figs

  6. Operation and control of an ion-implantation/sputtering storage device for 85Kr

    International Nuclear Information System (INIS)

    McClanahan, E.D.; Moss, R.W.; Greenwell, E.N.

    1986-01-01

    The design and operation of a device for implanting 85 Kr in a sputtered Cu-Y alloy for long-term storage tests are described. A total of approx.400 Ci of 85 Kr, in a 4.2% mixture with nonradioactive isotopes, was implanted in three batches at a rate of 6.1 sccm. A triode discharge operating at a pressure of 0.4 Pa with a plasma current of 4.5 A was maintained with a potential of 67 V. The target and substrate potentials were 2400 and 290, respectively, with an ion current density of approx.100 A/m 2 . The discharge and pumping action was started with nonradioactive Kr, then was switched to the radioactive gas until all in the reservoir was consumed, then again was switched to the nonradioactive gas to apply a closeout layer. The control feature used made it possible to empty the 85 Kr reservoir without use of an auxiliary pumping system. 13 refs., 4 figs

  7. Removal of I, Rn, Xe and Kr from off gas streams using PTFE membranes

    Science.gov (United States)

    Siemer, Darryl D.; Lewis, Leroy C.

    1990-01-01

    A process for removing I, R, Xe and Kr which involves the passage of the off gas stream through a tube-in-shell assembly, whereby the tubing is a PTFE membrane which permits the selective passages of the gases for removing and isolating the gases.

  8. 3H, 14C, 85Kr and 129I production in nuclear facilities

    International Nuclear Information System (INIS)

    Castellani, F.; Ocone, R.

    1984-01-01

    The production of 3 H, 14 C, 85 Kr and 129 I in nuclear power plants is evaluated. In particular the plant components where these radioisotopes can be formed and the formation processes, with corresponding cross sections, are considered. Furthermare their release in the plants and the fraction transfered to the reprocessing are examined

  9. Structure of collective bands and deformations in {sup 74,76}Kr

    Energy Technology Data Exchange (ETDEWEB)

    Tripathy, K.C. [Physics Department, F M College, Balasore, 756 001 (India); Sahu, R. [Physics Department, Berhampur University, Berhampur, 760 007 (India)

    2000-08-01

    The structure of collective bands in {sup 74,76}Kr is studied within the framework of the deformed configuration mixing shell model based on Hartree-Fock states. The active single-particle orbits are 1p{sub 3/2}, 0f{sub 5/2}, 1p{sub 1/2} and 0g{sub 9/2} with {sup 56}Ni as the inert core. A modified Kuo interaction has been used for the above configuration space. The {sup 74}Kr nucleus is found to be the most deformed nucleus among the krypton isotopes which is in agreement with experiment. The deformation is found to decrease for the {sup 76}Kr isotope. The calculated positive- and negative-parity bandsagree quite well with the experiment for both the nuclei. A number of excited bands is also predicted. We have also calculated B(E2) values and compared them with available experimental data. The structure of the strongly coupled band built on K = 4{sup (+)} in {sup 76}Kr is also studied. (author)

  10. Structure of collective bands and deformations in 74,76Kr

    International Nuclear Information System (INIS)

    Tripathy, K.C.; Sahu, R.

    2000-01-01

    The structure of collective bands in 74,76 Kr is studied within the framework of the deformed configuration mixing shell model based on Hartree-Fock states. The active single-particle orbits are 1p 3/2 , 0f 5/2 , 1p 1/2 and 0g 9/2 with 56 Ni as the inert core. A modified Kuo interaction has been used for the above configuration space. The 74 Kr nucleus is found to be the most deformed nucleus among the krypton isotopes which is in agreement with experiment. The deformation is found to decrease for the 76 Kr isotope. The calculated positive- and negative-parity bands agree quite well with the experiment for both the nuclei. A number of excited bands is also predicted. We have also calculated B(E2) values and compared them with available experimental data. The structure of the strongly coupled band built on K = 4 (+) in 76 Kr is also studied. (author)

  11. "Infootsingu 2010" võitja on Krõõt Kaljusto-Munck / Krista Lepik

    Index Scriptorium Estoniae

    Lepik, Krista, 1979-

    2010-01-01

    Raamatukoguhoidjate infootsingu võistluse eelvoorust, finaalist ja võitjatest. Lisa: Üks küsimus võitjatele. Mis on motiveerinud sind infootsingu võistlusel osalema? Vastavad Krõõt Kaljusto-Munck, Kristi Ütt ja Carolina Schultz

  12. Mød din nye kræftlæge: Dr. Microsoft

    DEFF Research Database (Denmark)

    Hokland, Peter

    2016-01-01

    Blogs og chats med beskrivelser af symptomer og bekymringer på nettet er blevet anvendt af forskere til at spore patienter, som efterfølgende får stillet en kræftdiagnose. I teorien kan søgemaskiner som Google og Bing stille diagnosen tidligere og måske redde menneskeliv....

  13. Independent yields of Kr and Xe isotopes for the photofission of heavy nuclei

    CERN Document Server

    Gangrskij, Y P; Mishinskij, G V; Penionzhkevich, Yu E; Szoelloes, O; Zhemenik, V I

    2002-01-01

    Presented are the yields of primary fission fragments (produced in the process of the rupture of the nucleus) of Kr (A = 87- 93) and Xe (A 148-143) for the photofission of sup 2 sup 3 sup 2 Th, sup 2 sup 3 sup 8 U and sup 2 sup 4 sup 4 Pu, which were measured using Bremsstrahlung from a microtron, the energy of accelerated electrons being 25 MeV. A technique was used that includes transportation of fragments escaped from the target with a gas flow through a capillary and the condensation of Kr and Xe inert gases in a cryostat at the temperature of liquid nitrogen. Fragments of all the other elements were retained with a filter at the entrance of the capillary. Kr and Xe isotopes were identified by the gamma spectra of their daughter products. The mass number distributions are obtained of the independent yields of Kr and Xe isotopes, which are compared with the similar characteristics for the fission induced by thermal and fast neutrons; the charge shifts for the fragments under study relative to the unchanged...

  14. Independent Yields of Kr and Xe Isotopes for the Photofission of Heavy Nuclei

    CERN Document Server

    Gangrsky, Yu P; Maslova, N Yu; Penionzhkevich, Yu E; Szöllös, O; Zhemenik, V I

    2002-01-01

    Presented are the yields of primary fission fragments (produced in the process of the rupture of the nucleus) of Kr (A=87-93) and Xe (A=148-143) for the photofission of ^{232}Th, ^{238}U and ^{244}Pu, which were measured using bremsstrahlung from a microtron, the energy of accelerated electrons being 25 MeV. A technique was used that includes transportation of fragments escaped from the target with a gas flow through a capillary and the condensation of Kr and Xe inert gases in a cryostat at the temperature of liquid nitrogen. Fragments of all the other elements were retained with a filter at the entrance of capillary. Kr and Xe isotopes were identified by the gamma-spectra of their daughter products. The mass number distributions are obtained of the independent yields of Kr and Xe isotopes, which are compared with the similar characteristics for the fission induced by thermal and fast neutrons; the charge shifts for the fragments under study relative to the unchanged charge distribution are determined. The pe...

  15. Independent yields of Kr and Xe isotopes in the photofission of heavy nuclei

    International Nuclear Information System (INIS)

    Gangrsky, Yu.P.; Zhemenik, V.I.; Maslova, N.Yu.; Mishinsky, G.V.; Penionzhkevich, Yu.E.; Szoelloes, O.

    2003-01-01

    The yields of Kr (A = 87-93) and Xe (A = 138-143) primary fission fragments produced in 232 Th, 238 U, and 244 Pu photofission upon the scission of a target nucleus and neutron emission were measured in an experiment with bremsstrahlung from electrons accelerated to 25 MeV by a microtron, and the results of these measurements are presented. The experimental procedure used involved the transportation of fragments that escaped from the target by a gas flow through a capillary and the condensation of Kr and Xe inert gases in a cryostat at liquid-nitrogen temperature. The fragments of all other elements were retained with a filter at the capillary inlet. The isotopes of Kr and Xe were identified by the γ spectra of their daughter products. The mass-number distributions of the independent yields of Kr and Xe isotopes are obtained and compared with similar data on fission induced by thermal and fast neutrons; the shifts of the fragment charges with respect to the undistorted charge distribution are determined. Prospects for using photofission fragments in studying the structure of highly neutron-rich nuclei are discussed

  16. Development of CO2 and KrF gas lasers as drivers for inertial confinement fusion

    International Nuclear Information System (INIS)

    Rockwood, S.D.

    1983-01-01

    Several different driver systems are currently under development in the national ICF program. Los Alamos has traditionally emphasized gas laser systems because of their intrinsic high average power capability and ease of operation. This paper will review the status of activities in both carbon dioxide (CO 2 ) and krypton fluoride (KrF) development at the Laboratory

  17. Nuclear binding around the RP-process waiting points $^{68}$Se and $^{72}$Kr

    CERN Multimedia

    2002-01-01

    Encouraged by the success of mass determinations of nuclei close to the Z=N line performed at ISOLTRAP during the year 2000 and of the recent decay spectroscopy studies on neutron-deficient Kr isotopes (IS351 collaboration), we aim to measure masses and proton separation energies of the bottleneck nuclei defining the flow of the astrophysical rp-process beyond A$\\sim$70. In detail, the program includes mass measurements of the rp-process waiting point nuclei $^{68}$Se and $^{72}$Kr and determination of proton separation energies of the proton-unbound $^{69}$Br and $^{73}$Rb via $\\beta$-decays of $^{69}$Kr and $^{73}$Sr, respectively. The aim of the project is to complete the experimental database for astrophysical network calculations and for the liquid-drop type of mass models typically used in the modelling of the astrophysical rp process in the region. The first beamtime is scheduled for the August 2001 and the aim is to measure the absolute mass of the waiting-point nucleus $^{72}$Kr.

  18. First results of 35 MeV/u Kr + Au experiment at GANIL (Caen)

    International Nuclear Information System (INIS)

    Adloff, J.C.; Boishu, B.; Dalili, D.

    1984-01-01

    Preliminary results of a study of the Kr + Au breakup reaction at 35 MeV/u performed at GANIL are presented. Atomic number versus velocity distributions are presented for reaction fragments under various conditions. The results are explained by a kinematic model involving fast binary reactions followed by sequential decays by fission

  19. A flickering study of nova-like systems KR Aur and UU Aqr

    Science.gov (United States)

    Dobrotka, A.; Mineshige, S.; Casares, J.

    2012-03-01

    We present a study of the flickering activity in two nova-like systems, KR Aur and UU Aqr. We applied a statistical model of flickering simulations in accretion discs based on turbulent angular momentum transport between two adjacent rings with an exponential distribution of the turbulence dimension scale. The model is based on a steady-state disc model, which is satisfied in the case of hot ionized discs of nova-like cataclysmic variables. Our model successfully fits the observed power-density spectrum of KR Aur with the disc parameter α= 0.10-0.40 and an inner-disc truncation radius in the range Rin= 0.88-1.67 × 109 cm. The exact values depend on the mass-transfer rate in the sense that α decreases and Rin increases with mass-transfer rate. In any case, the inner-disc radius found for KR Aur is considerably smaller than those for quiescent dwarf novae, as predicted by the disc instability model. On the other hand, our simulations fail to reproduce the power-density spectrum of UU Aqr. A tantalizing explanation involves the possible presence of spiral waves, which are expected in UU Aqr because of its low mass ratio but not in KR Aur. In general our model predicts the observed concentration of flickering in the central disc. We explain this by the radial dependence of the angular-momentum gradient.

  20. Structure studies on 82Kr by means of the multiple Coulomb excitation

    International Nuclear Information System (INIS)

    Bruessermann, S.

    1985-01-01

    With a 82 Kr beam of the energy 4.6 MeV per nucleon a 208 Pb target was irradiated in order to study the Coulomb excitation of 82 Kr. The experiment has been performed at the Society for Heavy Ion Research (GSI) in Darmstadt. The 82 Kr ions backscattered on the 208 Pb target were detected in a position-sensitive parallel-plate avalanche detector. The γ radiation of the excited 82 Kr particles was detected in 4 Ge(Li) detectors in coincidence with the particles. The spectra corrected regarding the Doppler shift contained 16 lines which permitted to determine by means of known mixing and branching ratios 22 electrical quadrupole transition matrix elements. The experimental excitation energies and the transition probabilities determined in this thesis are compared with different nuclear models, like the asymmetric rotator model, the rotational-vibrational model, the harmonic-oscillator model, the nuclear field theory, the SU(5) limit of the IBA-1, and the IBA-2 model. Thereby within the IBA-2 model a criterium for the symmetry of the wavefunction relative to the proton and neutron contributions is elaborated. Because of this criterium to the 2 1 + state a symmetric structure and to the 2 2 + ,3 states an asymmetric structure is assigned. (orig.) [de

  1. Lactococcus lactis KR-050L inhibit IL-6/STAT3 activation.

    Science.gov (United States)

    Hwang, J T; Jang, H-J; Kim, J H; Park, C S; Kim, Y; Lim, C-H; Lee, S W; Rho, M-C

    2017-05-01

    The purpose of this study was to investigate IL-6/STAT3 inhibitory activity using lactic acid bacteria (LABs) isolated from Gajuknamu kimchi. Six LABs were isolated from Gajuknamu kimchi and identified through 16S rRNA sequencing. Among them, the culture broth of Lactococcus lactis KR-050L inhibited IL-6-induced STAT3 luciferase activity. Fifteen compounds were isolated from the EtOAc extract of culture broth though column chromatography and preparative high-performance liquid chromatography, and they were identified as 2,5-diketopipperazine structures by spectroscopic analyses (MS, 1 H- and 13 C-NMR). They also showed inhibitory activities on IL-6-induced STAT3 activation, and showed the different in activity according to the presence of a phenylalanine residue, hydroxyl groups and isometric structure. The six new LABs isolated from Gajuknamu kimchi, and Lc. lactis KR-050L was selected as candidate IL-6/STAT3 inhibitors. The activity levels of 15 2,5-DKPs isolated from Lc. lactis KR-050L were verified. This study constitutes the first attempt to isolate various LABs from Gajuknamu kimchi and to discover IL-6/STAT3 inhibitors in the EtOAc extract of Lc. lactis KR-050L culture broth. Moreover, our data provide useful biochemical information regarding the commercialization of Lc. lactis isolated from Gajuknamu kimchi as an approach to use functional foods for the treatment of various diseases via IL-6/STAT3 activation. © 2017 The Society for Applied Microbiology.

  2. Establishing release limits for 3H, 14C, 85Kr, and 129I

    International Nuclear Information System (INIS)

    Kocher, D.C.; Killough, G.G.

    1983-01-01

    Tritium ( 3 H), 14 C, 85 Kr, and 129 I are the most important globally dispersed radionuclides released from the nuclear fuel cycle. In this paper, we investigate whether global transport of these radionuclides could also be important in assessing doses to individuals in critical groups of the population

  3. Gas-Liquid Precipitation of water dissolved heavy metal ions using hydrogen sulfide gas

    NARCIS (Netherlands)

    Al Tarazi, M.Y.M.

    2004-01-01

    Precipitation of solids promoted by gas-liquid reactions is applied in many industrial processes such as the production of ammonium phosphate, ammonium sulphate, barium carbonate, calcium carbonate, calcium fluoride, ypsum (calcium sulphate), goethite, sodium bicarbonate, strontium carbonate and

  4. Evaluating the Long-Term Stability of Metals Precipitated In-Situ

    Science.gov (United States)

    Because metals (including metals and metalloids) cannot be destroyed, unlike organic contaminants, in-situ approaches for their removal from groundwater necessarily involves fixation/immobilization in the solid aquifer matrix. Consequently, the success of precipitation based in...

  5. DISSOLUTION OF LANTHANUM FLUORIDE PRECIPITATES

    Science.gov (United States)

    Fries, B.A.

    1959-11-10

    A plutonium separatory ore concentration procedure involving the use of a fluoride type of carrier is presented. An improvement is given in the derivation step in the process for plutonium recovery by carrier precipitation of plutonium values from solution with a lanthanum fluoride carrier precipitate and subsequent derivation from the resulting plutonium bearing carrier precipitate of an aqueous acidic plutonium-containing solution. The carrier precipitate is contacted with a concentrated aqueous solution of potassium carbonate to effect dissolution therein of at least a part of the precipitate, including the plutonium values. Any remaining precipitate is separated from the resulting solution and dissolves in an aqueous solution containing at least 20% by weight of potassium carbonate. The reacting solutions are combined, and an alkali metal hydroxide added to a concentration of at least 2N to precipitate lanthanum hydroxide concomitantly carrying plutonium values.

  6. Differential expression of hERG1 channel isoforms reproduces properties of native I(Kr) and modulates cardiac action potential characteristics

    DEFF Research Database (Denmark)

    Larsen, Anders Peter; Olesen, Søren-Peter

    2010-01-01

    The repolarizing cardiac rapid delayed rectifier current, I(Kr), is composed of ERG1 channels. It has been suggested that two isoforms of the ERG1 protein, ERG1a and ERG1b, both contribute to I(Kr). Marked heterogeneity in the kinetic properties of native I(Kr) has been described. We hypothesized...

  7. Core drilling of deep borehole OL-KR39 at Olkiluoto in Eurajoki 2005

    Energy Technology Data Exchange (ETDEWEB)

    Niinimaeki, R. [Suomen Malmi Oy, Espoo (Finland)

    2005-11-15

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 502.97 m and 45.11 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in August- October 2005. The identification numbers of the boreholes are OL-KR39 and OL-KR39B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the drilling water and the returning water were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 415m{sup 3} and 25 m{sup 3} and the measured volumes of the returning water were 175 m{sup 3} and 7 m{sup 3} in boreholes OLKR39 and OL-KR39B, respectively. The deviation of the borehole was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson' s ratio were measured from the core samples. The average uniaxial compressive strength is about 110 MPa, the average Young's Modulus is 49 GP a and the average Poisson' s ratio is 0.25. The main rock types are migmatitic mica gneiss and granite. Filled fracture is the most common

  8. Core drilling of deep borehole OL-KR39 at Olkiluoto in Eurajoki 2005

    International Nuclear Information System (INIS)

    Niinimaeki, R.

    2005-11-01

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 502.97 m and 45.11 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in August- October 2005. The identification numbers of the boreholes are OL-KR39 and OL-KR39B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the drilling water and the returning water were recorded. The drill rig was computer controlled and during drilling the computer recorded drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 415m 3 and 25 m 3 and the measured volumes of the returning water were 175 m 3 and 7 m 3 in boreholes OLKR39 and OL-KR39B, respectively. The deviation of the borehole was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson' s ratio were measured from the core samples. The average uniaxial compressive strength is about 110 MPa, the average Young's Modulus is 49 GP a and the average Poisson' s ratio is 0.25. The main rock types are migmatitic mica gneiss and granite. Filled fracture is the most common fracture type. The average fracture

  9. Ropniak nadtwardówkowy kanału kręgowego

    Directory of Open Access Journals (Sweden)

    Dariusz J. Jaskólski

    2014-07-01

    Full Text Available Ropniakiem nadtwardówkowym kanału kręgowego nazywamy zbiornik ropy położony nad oponą twardą krę- gosłupa. Bywa powikłaniem zapalenia krążka międzykręgowego oraz zapalenia kości trzonu kręgu, lecz znacznie częściej powstaje w efekcie rozsiewu zakażenia (układu moczowego, wsierdzia, płuc drogą krwiopochodną. Jest dwukrotnie częstszy u mężczyzn; występuje zwykle u chorych powyżej 30. roku życia. Czynniki ryzyka to: narkomania, immunosupresja, cukrzyca, alkoholizm, obecność ognisk zakażenia i przebycie operacji lub otwartego urazu kręgosłupa. Źródło infekcji pozostaje niewykryte u <40% osób. Znamienna triada objawów obejmuje gorączkę, silny miejscowy ból kręgosłupa i postępujący zespół neurologiczny. Wczesne rozpoznanie stanowi niezwykle ważny aspekt – leczenie może wprawdzie zapobiec rozwojowi deficytu neurologicznego, lecz żadną miarą nie daje pewności jego ustąpienia. Do postawienia właściwej diagnozy niezbędne jest wykonanie badań obrazowych, najlepiej MRI. Leczenie polega na chirurgicznym usunięciu ropniaka i długotrwałej antybiotykoterapii. Zabieg operacyjny ma na celu odbarczenie elementów nerwowych, staranną ewakuację ropy i ziarniny zapalnej oraz uzyskanie materiału do badań mikrobiologicznych. Śmiertelność sięga 16%. Rokowanie co do funkcji zależy przede wszystkim od początkowego stanu neurologicznego i czasu trwania deficytów – jeśli przekracza on 72 godziny, nie ma szans na poprawę. Czynniki negatywnie wpływające na rokowanie to: obecność współ- istniejących chorób, przebycie wielokrotnej operacji kręgosłupa, ropniak w odcinku piersiowym oraz zakażenie szczepem MRSA.

  10. Investigation of Neptunium Precipitator Cleanout Options

    International Nuclear Information System (INIS)

    Hill, B.C.

    2003-01-01

    Oxalate precipitation followed by filtration is used to prepare plutonium oxalate. Historically, plutonium oxalate has tended to accumulate in the precipitation tanks. These solids are periodically removed by flushing with concentrated (64 percent) nitric acid. The same precipitation tanks will now be used in the processing of neptunium. Literature values indicate that neptunium oxalate may not be as soluble as plutonium oxalate in nitric acid. Although a wide variety of options is available to improve neptunium oxalate solubility for precipitator flushing, most of these options are not practical for use. Many of these options require the use of incompatible or difficult to handle chemicals. Other options would require expensive equipment modifications or are likely to lead to product contamination. Based on review of literature and experimental results, the two best options for flushing the precipitator are (1) 64 percent nitric acid and (2) addition of sodium permanganate follow ed by sodium nitrite. Nitric acid is the easiest option to implement. It is already used in the facility and will not lead to product contamination. Experimental results indicate that neptunium oxalate can be dissolved in concentrated nitric acid (64 percent) at 60 degree C to a concentration of 2.6 to 5.6 grams of Np/liter after at least three hours of heating. A lower concentration (1.1 grams of Np/liter) was measured at 60 degree C after less than two hours of heating. These concentrations are acceptable for flushing if precipitator holdup is low (approximately 100-250 grams), but a second method is required for effective flushing if precipitator holdup is high (approximately 2 kilograms). The most effective method for obtaining higher neptunium concentrations is the use of sodium permanganate followed by the addition of sodium nitrite. There is concern that residual manganese from these flushes could impact product purity. Gas generation during permanganate addition is also a concern

  11. A novel electrostatic precipitator

    International Nuclear Information System (INIS)

    Tang, Minkang; Wang, Liqian; Lin, Zhigui

    2013-01-01

    ESP (Electrostatic Precipitation) has been widely used in the mining, building materials, metallurgy and power industries. Dust particles or other harmful particles from the airstream can be precipitated by ESP with great collecting efficiency. Because of its' large size, high cost and energy consumption, the scope of application of ESP has been limited to a certain extent. By means of the theory of electrostatics and fluid dynamics, a corona assembly with a self-cleaning function and a threshold voltage automatic tracking technology has been developed and used in ESP. It is indicated that compared with conventional ESP, the electric field length has been reduced to 1/10 of the original, the current density on the collecting electrode increased 3-5 times at the maximum, the approach speed of dust particles in the electric field towards the collecting electrode is 4 times that in conventional ESP and the electric field wind speed may be enhanced by 2-3 times the original. Under the premise of ESP having a high efficiency of dust removal, equipment volume may be actually reduced to 1/5 to 1/10 of the original volume and energy consumption may be reduced by more than 50%.

  12. Development of Bread Board Model of TRMM precipitation radar

    Science.gov (United States)

    Okamoto, Ken'ichi; Ihara, Toshio; Kumagai, Hiroshi

    The active array radar was selected as a reliable candidate for the TRMM (Tropical Rainfall Measuring Mission) precipitation radar after the trade off studies performed by Communications Research Laboratory (CRL) in the US-Japan joint feasibility study of TRMM in 1987-1988. Main system parameters and block diagram for TRMM precipitation radar are shown as the result of feasibility study. CRL developed key devices for the active array precipitation radar such as 8-element slotted waveguide array antenna, the 5 bit PIN diode phase shifters, solid state power amplifiers and low noise amplifiers in 1988-1990. Integration of these key devices was made to compose 8-element Bread Board Model of TRMM precipitation radar.

  13. A 1-kJ KrF laser system for laser fusion research

    International Nuclear Information System (INIS)

    Owadano, Y.; Okuda, I.; Tanimoto, M.; Matsumoto, Y.; Yaoita, A.; Komeiji, S.; Yano, M.

    1987-01-01

    Ultraviolet laser light has several advantages in coupling with a laser fusion target, and the KrF laser is considered to be a promising candidate for the driver because of its short wavelength, high overall efficiency, and scalability to a megajoule class system. The Electrotechnical Laboratory is developing a 1-kJ class KrF laser system to perform target-shooting experiments in the 10/sup 13/-10/sup 15/-W/cm/sup 2/, 10-20-ns range and to investigate the possibility of a compact laser fusion driver which operates at a high pumping density and high laser power density. Based on the pulsed-power technology used in Amp2 and the characteristics of the Kr-rich mixture measured, Amp3 was designed to operate at high optical power density with a Kr-rich mixture. Amp3 has four PFLs charged by a single 40-kJ Marx generator and four e-beam diodes (550 kV, 4 Ω) arranged cylindrically around the laser cell. The active volume is 660 cm/sup 2/ (29 cm in diameter) X 1 m, and 2-atm Kr is pumped at a density of 1.9 MW/cm/sup 3/. Output energy of 1 kJ is expected at an intrinsic efficiency of 8.3% and overall efficiency of 2.5%. Output energy fluence is 1.5 J/cm/sup 2/ (15 MW/cm/sup 2/) on average, which is lower than the damage threshold of our fully reflecting AR coatings (>3 J/cm/sup 2/)

  14. Enhancing the Effectiveness of Carbon Dioxide Flooding by Managing Asphaltene Precipitation

    Energy Technology Data Exchange (ETDEWEB)

    Deo, M.D.

    2001-01-12

    The objective of this project was to identify conditions at which carbon dioxide induced precipitation occurred in crude oils. Establishing compositions of the relevant liquid and solid phases was planned. Other goals of the project were to determine if precipitation occurred in cores and to implement thermodynamic and compositional models to examine the phenomenon. Exploring kinetics of precipitation was also one of the project goals. Crude oil from the Rangely Field (eastern Colorado) was used as a prototype.

  15. The Global Precipitation Climatology Project (GPCP) Combined Precipitation Dataset

    Science.gov (United States)

    Huffman, George J.; Adler, Robert F.; Arkin, Philip; Chang, Alfred; Ferraro, Ralph; Gruber, Arnold; Janowiak, John; McNab, Alan; Rudolf, Bruno; Schneider, Udo

    1997-01-01

    The Global Precipitation Climatology Project (GPCP) has released the GPCP Version 1 Combined Precipitation Data Set, a global, monthly precipitation dataset covering the period July 1987 through December 1995. The primary product in the dataset is a merged analysis incorporating precipitation estimates from low-orbit-satellite microwave data, geosynchronous-orbit -satellite infrared data, and rain gauge observations. The dataset also contains the individual input fields, a combination of the microwave and infrared satellite estimates, and error estimates for each field. The data are provided on 2.5 deg x 2.5 deg latitude-longitude global grids. Preliminary analyses show general agreement with prior studies of global precipitation and extends prior studies of El Nino-Southern Oscillation precipitation patterns. At the regional scale there are systematic differences with standard climatologies.

  16. Optimization of precipitation conditions of thorium oxalate precipitate

    International Nuclear Information System (INIS)

    Pazukhin, Eh.M.; Smirnova, E.A.; Krivokhatskij, A.S.; Pazukhina, Yu.L.; Kiselev, P.P.

    1986-01-01

    Thorium precipitation in the form of difficultly soluble oxalate has been investigated. The equation binding the concentration of metal with the nitric acid in the initial solution and quantity of a precipitator necessary for minimization of desired product losses is derived. The graphical solution of this equation for a case, when the oxalic acid with 0.78 mol/l concentration is the precipitator, is presented

  17. Preventing Precipitation in the ISS Urine Processor

    Science.gov (United States)

    Muirhead, Dean; Carter, Layne; Williamson, Jill; Chambers, Antja

    2017-01-01

    The ISS Urine Processor Assembly (UPA) was initially designed to achieve 85% recovery of water from pretreated urine on ISS. Pretreated urine is comprised of crew urine treated with flush water, an oxidant (chromium trioxide), and an inorganic acid (sulfuric acid) to control microbial growth and inhibit precipitation. Unfortunately, initial operation of the UPA on ISS resulted in the precipitation of calcium sulfate at 85% recovery. This occurred because the calcium concentration in the crew urine was elevated in microgravity due to bone loss. The higher calcium concentration precipitated with sulfate from the pretreatment acid, resulting in a failure of the UPA due to the accumulation of solids in the Distillation Assembly. Since this failure, the UPA has been limited to a reduced recovery of water from urine to prevent calcium sulfate from reaching the solubility limit. NASA personnel have worked to identify a solution that would allow the UPA to return to a nominal recovery rate of 85%. This effort has culminated with the development of a pretreatment based on phosphoric acid instead of sulfuric acid. By eliminating the sulfate associated with the pretreatment, the brine can be concentrated to a much higher concentration before calcium sulfate reach the solubility limit. This paper summarizes the development of this pretreatment and the testing performed to verify its implementation on ISS.

  18. Hairy foam" : carbon nanofibers grown on solid foam. A fully accessible, high surface area, graphitic catalyst support

    NARCIS (Netherlands)

    Wenmakers, P.W.A.M.; Schaaf, van der J.; Kuster, B.F.M.; Schouten, J.C.

    2008-01-01

    This paper describes the synthesis of carbon nanofibers (CNFs) on solid carbon foam ("Hairy Foam") by catalytic decompn. of ethylene. The effect of nickel loading on fiber diam. and morphol., CNF coverage, and fiber layer thickness is studied using SEM and N2/Kr-physisorption. The surface area

  19. Production of 81Rb/sup 81m/Kr generators with 60-MeV protons at BLIP

    International Nuclear Information System (INIS)

    Mausner, L.F.; Richards, P.

    1983-01-01

    By bombarding natural krypton gas with approx. 63 MeV protons, 81 Rb is formed by (p,4n) reaction from high abundance 84 Kr (57%) as well as some additional contribution from 83 Kr (11.5%) and 82 Kr (11.6%) by (p,3n) and (p,2n) reactions, respectively. The production rate of 81 Rb is typically 1.5 mCi/μAh. This production rate is sufficient to create up to several hundred millicuries per run if necessary, enough for several high activity 81 Rb/sup 81m/Kr generators. Presently generators that deliver 10 to 20 mCi to the lungs are produced weekly for on-site use. The only other important activity in the solution is Rb-82m (6.4 hr). Small amounts of Br-76 (16.1 hr), Br-77 (57 hr), Br-82 (35.5 hr), Rb-83 (86.2 d), and Rb-84 (33 d) were also present. The bromine impurities pose no problem since they are not trapped on the generator. Rb-82m and Rb-84 decay to stable Kr-82 and Kr-84 in the generator and do not interfere with Kr-81m studies

  20. Precipitate coarsening parameters for gas induced semi-solid cast ...

    Indian Academy of Sciences (India)

    1Faculty of Science and Industrial Technology, Prince of Songkla ... 2Department of Mechanical Engineering, Faculty of Engineering, Prince of ... MS received 3 August 2016; accepted 27 March 2017; published online 31 October 2017.

  1. Acid precipitation literature review

    Energy Technology Data Exchange (ETDEWEB)

    Seip, H M; Andersen, B; Andersson, G; Hov, Oe; Kucera, V; Moseholm, L

    1986-01-01

    There is an increasing number of publications on acid deposition and related phenomena. Interest in these topics has also been reflected in a considerable number of meetings and conferences in this field. The largest of these in 1985 was the ''International Symposium on Acidic Precipitation'' (Muskoka, Ontario). Most work so far has been carried out in North America and Europe. There is, however, an increasing interest in obtaining a better picture of sensitive areas and possible acidification in other parts of the world. Anthropogenic SO/sub 2/ emissions have been estimated to be (in TgSyr/sup -1/): 2.4 (Africa), 4.1 (South America), 0.7 (Ocenia), and 18.3 (Asia). The largest increase during the last decade has been in Asia. Based on Studies of precipitation in remote areas it has been suggested that the natural background concentration for sulphate in many areas should be about 6 ..mu..eq 1/sup -1/. A new study of sulphate and nitrate in Greenland snow showed that both ions increased by a factor of about 2 from 1895 to 1978. The concentrations of SO/sub 2/ at Norwegian rural sites show a decreasing trend since late 1970s, while concentrations of sulphate in air show no clear trend. More reliable models for transformation, transport and deposition of chemicals are being developed, including three-dimensional grid models to describe episodes of elevated pollution levels lasting for a few days. Model calculations indicate that control of hydrocarbon (HC) emissions is much more efficient in reducing the ozone level in southern Scandinavia in episodes influenced by long-range transported pollutants than NO/sub x/ control of combined NO/sub x/ and HC control. 36 refs. (EG).

  2. Mid-embryo patterning and precision in Drosophila segmentation: Krüppel dual regulation of hunchback.

    Directory of Open Access Journals (Sweden)

    David M Holloway

    Full Text Available In early development, genes are expressed in spatial patterns which later define cellular identities and tissue locations. The mechanisms of such pattern formation have been studied extensively in early Drosophila (fruit fly embryos. The gap gene hunchback (hb is one of the earliest genes to be expressed in anterior-posterior (AP body segmentation. As a transcriptional regulator for a number of downstream genes, the spatial precision of hb expression can have significant effects in the development of the body plan. To investigate the factors contributing to hb precision, we used fine spatial and temporal resolution data to develop a quantitative model for the regulation of hb expression in the mid-embryo. In particular, modelling hb pattern refinement in mid nuclear cleavage cycle 14 (NC14 reveals some of the regulatory contributions of simultaneously-expressed gap genes. Matching the model to recent data from wild-type (WT embryos and mutants of the gap gene Krüppel (Kr indicates that a mid-embryo Hb concentration peak important in thoracic development (at parasegment 4, PS4 is regulated in a dual manner by Kr, with low Kr concentration activating hb and high Kr concentration repressing hb. The processes of gene expression (transcription, translation, transport are intrinsically random. We used stochastic simulations to characterize the noise generated in hb expression. We find that Kr regulation can limit the positional variability of the Hb mid-embryo border. This has been recently corroborated in experimental comparisons of WT and Kr- mutant embryos. Further, Kr regulation can decrease uncertainty in mid-embryo hb expression (i.e. contribute to a smooth Hb boundary and decrease between-copy transcriptional variability within nuclei. Since many tissue boundaries are first established by interactions between neighbouring gene expression domains, these properties of Hb-Kr dynamics to diminish the effects of intrinsic expression noise may

  3. Core drilling of deep borehole OL-KR33 at Olkiluoto in Eurajoki 2004

    Energy Technology Data Exchange (ETDEWEB)

    Rautio, T. [Suomen Malmi Oy, Espoo (Finland)

    2005-01-15

    Posiva Oy submitted an application for the Decision in Principle to the Finnish Government in May 1999. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the Decision in Principle on the final disposal facility for spent nuclear fuel at Olkiluoto, Eurajoki in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, the ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 311.02 m and 45.53 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in November-December 2004. These boreholes were aimed to get additional information of the quality of bedrock and the quality and the location of the fractured zones R2, RH9 and R72. The identification numbers of the boreholes are OL-KR33 and OL-KR33B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the drilling water and the returning water were recorded as well as the pressure of the drilling water. The objective of these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The volumes of the used drilling water were about 195m{sup 3} and 14m{sup 3} and the measured volumes of the returning water were about 100 m{sup 3} and 9 m{sup 3} in boreholes OL-KR33 and OL-KR33B, respectively. The deviations of the boreholes were measured with the deviation measuring instruments EMS and Maxibor. The results of the Maxibor measurements indicate that borehole OL-KR33 deviates 15.97 m right and 31.04 m up at the borehole depth of 309 m. Uniaxial compressive strength, Young's Modulus and Poisson's ratio were measured from the core samples. The average uniaxial compressive

  4. Two-stage precipitation of plutonium trifluoride

    International Nuclear Information System (INIS)

    Luerkens, D.W.

    1984-04-01

    Plutonium trifluoride was precipitated using a two-stage precipitation system. A series of precipitation experiments identified the significant process variables affecting precipitate characteristics. A mathematical precipitation model was developed which was based on the formation of plutonium fluoride complexes. The precipitation model relates all process variables, in a single equation, to a single parameter that can be used to control particle characteristics

  5. Thermodynamics Prediction of Wax Precipitation in Black Oil Using Regular Solution Model and Plus Fraction Characterization

    Directory of Open Access Journals (Sweden)

    Wei Wang

    2013-01-01

    Full Text Available The precipitation of wax/solid paraffin during production, transportation, and processing of crude oil is a serious problem. It is essential to have a reliable model to predict the wax appearance temperature and the amount of solid precipitated at different conditions. This paper presents a work to predict the solid precipitation based on solid-liquid equilibrium with regular solution-molecular thermodynamic theory and characterization of the crude oil plus fraction. Due to the differences of solubility characteristics between solid and liquid phase, the solubility parameters of liquid and solid phase are calculated by a modified model. The heat capacity change between solid and liquid phase is considered and estimated in the thermodynamic model. An activity coefficient based thermodynamic method combined with two characteristic methods to calculate wax precipitation in crude oil, especially heavy oil, has been tested with experimental data. The results show that the wax appearance temperature and the amount of weight precipitated can be predicted well with the experimental data.

  6. Effective Assimilation of Global Precipitation

    Science.gov (United States)

    Lien, G.; Kalnay, E.; Miyoshi, T.; Huffman, G. J.

    2012-12-01

    Assimilating precipitation observations by modifying the moisture and sometimes temperature profiles has been shown successful in forcing the model precipitation to be close to the observed precipitation, but only while the assimilation is taking place. After the forecast start, the model tends to "forget" the assimilation changes and lose their extra skill after few forecast hours. This suggests that this approach is not an efficient way to modify the potential vorticity field, since this is the variable that the model would remember. In this study, the ensemble Kalman filter (EnKF) method is used to effectively change the potential vorticity field by allowing ensemble members with better precipitation to receive higher weights. In addition to using an EnKF, two other changes in the precipitation assimilation process are proposed to solve the problems related to the highly non-Gaussian nature of the precipitation variable: a) transform precipitation into a Gaussian distribution based on its climatological distribution, and b) only assimilate precipitation at the location where some ensemble members have positive precipitation. The idea is first tested by the observing system simulation experiments (OSSEs) using SPEEDY, a simplified but realistic general circulation model. When the global precipitation is assimilated in addition to conventional rawinsonde observations, both the analyses and the medium range forecasts are significantly improved as compared to only having rawinsonde observations. The improvement is much reduced when only modifying the moisture field with the same approach, which shows the importance of the error covariance between precipitation and all other model variables. The effect of precipitation assimilation is larger in the Southern Hemisphere than that in the Northern Hemisphere because the Northern Hemisphere analyses are already accurate as a result of denser rawinsonde stations. Assimilation of precipitation using a more comprehensive

  7. Electrical operation of electrostatic precipitators

    CERN Document Server

    Parker, Ken

    2003-01-01

    The electrostatic precipitator remains on of the most cost effective means of controlling the emission of particulates from most industrial processes. This book will be of interest to both users and suppliers of electrostatic precipitators as well as advanced students on environmental based courses. The author identifies the physical and engineering basis for the development of electrical equipment for electrostatic precipitators and thoroughly explores the technological factors which optimize the efficiency of the precipitator and hence minimize emissions, as well as future developments in th

  8. Effect of KrF excimer laser irradiation on the surface changes and photoelectric properties of ZnO single crystal

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, Yong [Institute of Laser Engineering, Beijing University of Technology, Beijing 100124 (China); Beijing Engineering Research Center of 3D Printing for Digital Medical Health, Beijing International Cooperation Base of 3D Printing for Digital MedicalHealth, Beijing University of Technology, Beijing 100124 (China); Zhao, Yan [Institute of Laser Engineering, Beijing University of Technology, Beijing 100124 (China); Jiang, Yijian, E-mail: yjjiang@bjut.edu.cn [Institute of Laser Engineering, Beijing University of Technology, Beijing 100124 (China); Beijing Engineering Research Center of 3D Printing for Digital Medical Health, Beijing International Cooperation Base of 3D Printing for Digital MedicalHealth, Beijing University of Technology, Beijing 100124 (China)

    2016-06-25

    In this paper, the effect of KrF pulsed excimer laser irradiation on the structural, surface morphology, photoluminescence and electrical properties of ZnO single crystal was investigated. Compared to the as-grown sample, at an irradiation energy density of 257 mJ/cm{sup 2}, the ZnO single crystal exhibits a series of phenomenon: XRD and Raman results show that the crystallization of ZnO quality change slightly, resistivity is decreased by two orders of magnitude, carrier concentration is increased by one order of magnitude. After laser irradiation, the surface shows some strip lines and no cracks. Formula calculation and simulation results show that the stripes are not caused by surface melting. We speculate that these stripes are caused by the precipitation of ZnO material inside to the surface. Due to the reduction of oxygen vacancies, UV emission has been enhanced and visible emission has been declined after irradiation. After the laser irradiation, the visible light of ZnO surface can be regulated. The experimental results show that KrF laser irradiation could effectively improve the optical and electrical properties of ZnO single crystal, which is important for the application of high performance of emitting optoelectronic devices. - Highlights: • After laser irradiation, the surface shows some strip lines and no cracks. • The visible light of as-irradiated ZnO surface can be regulated to four colors. • The electrical properties of as-irradiated ZnO has been improved greatly.

  9. KrF laser development for fusion energy

    International Nuclear Information System (INIS)

    Wolford, Matthew F.; Sethian, John D.; Myers, Matthew C.; Giuliani, John L.; Obenschain, Stephen P.; Hegeler, Frank

    2013-01-01

    The United States Naval Research Laboratory is developing an electron beam pumped krypton fluoride laser technology for a direct drive inertial fusion energy power plant. The repetitively pulsed krypton fluoride laser technology being developed meets the fusion energy requirements for laser beam quality, wavelength, and repetition rate. The krypton fluoride laser technology is projected, based on experiments, to meet the requirements for wall plug efficiency and durability. The projected wall plug efficiency based on experiments is greater than 7 percent. The Electra laser using laser triggered gas switches has conducted continuous operation for 90,000 shots at 2.5 Hertz operation (ten hours). The Electra laser has achieved greater than 700 Joules per pulse at 1 and 2.5 Hertz repetition rate. The comparison of krypton fluoride laser performance with krypton fluoride kinetics code shows good agreement for pulse shape and laser yield. Development and operation of a durable pulse power system with solid state switches has achieved a continuous run of 11 million pulses into a resistive load at 10 Hz. (author)

  10. Nanocrystalline solids

    International Nuclear Information System (INIS)

    Gleiter, H.

    1991-01-01

    Nanocrystalline solids are polycrystals, the crystal size of which is a few (typically 1 to 10) nanometres so that 50% or more of the solid consists of incoherent interfaces between crystals of different orientations. Solids consisting primarily of internal interfaces represent a separate class of atomic structures because the atomic arrangement formed in the core of an interface is known to be an arrangement of minimum energy in the potential field of the two adjacent crystal lattices with different crystallographic orientations on either side of the boundary core. These boundary conditions result in atomic structures in the interfacial cores which cannot be formed elsewhere (e.g. in glasses or perfect crystals). Nanocrystalline solids are of interest for the following four reasons: (1) Nanocrystalline solids exhibit an atomic structure which differs from that of the two known solid states: the crystalline (with long-range order) and the glassy (with short-range order). (2) The properties of nanocrystalline solids differ (in some cases by several orders of magnitude) from those of glasses and/or crystals with the same chemical composition, which suggests that they may be utilized technologically in the future. (3) Nanocrystalline solids seem to permit the alloying of conventionally immiscible components. (4) If small (1 to 10 nm diameter) solid droplets with a glassy structure are consolidated (instead of small crystals), a new type of glass, called nanoglass, is obtained. Such glasses seem to differ structurally from conventional glasses. (orig.)

  11. Solid Matter

    CERN Document Server

    Angelo, Joseph A

    2011-01-01

    Supported by a generous quantity of full-color illustrations and interesting sidebars, Solid Matter introduces the basic characteristics and properties of solid matter. It briefly describes the cosmic connection of the elements, leading readers through several key events in human pre-history that resulted in more advanced uses of matter in the solid state. Chapters include:. -Solid Matter: An Initial Perspective. -Physical Behavior of Matter. -The Gravity of Matter. -Fundamentals of Materials Science. -Rocks and Minerals. -Metals. -Building Materials. -Carbon Earth's Most Versatile Element. -S

  12. Improving precipitation measurement

    Science.gov (United States)

    Strangeways, Ian

    2004-09-01

    Although rainfall has been measured for centuries scientifically and in isolated brief episodes over millennia for agriculture, it is still not measured adequately even today for climatology, water resources, and other precise applications. This paper outlines the history of raingauges, their errors, and describes the field testing over 3 years of a first guess design for an aerodynamic rain collector proposed by Folland in 1988. Although shown to have aerodynamic advantage over a standard 5 gauge, the new rain collector was found to suffer from outsplash in heavy rain. To study this problem, and to derive general basic design rules for aerodynamic gauges, its performance was investigated in turbulent, real-world conditions rather than in the controlled and simplified environment of a wind tunnel or mathematical model as in the past. To do this, video records were made using thread tracers to indicate the path of the wind, giving new insight into the complex flow of natural wind around and within raingauges. A new design resulted, and 2 years of field testing have shown that the new gauge has good aerodynamic and evaporative characteristics and minimal outsplash, offering the potential for improved precipitation measurement.

  13. CEOS precipitation constellation

    Science.gov (United States)

    Neeck, Steven P.; Oki, Riko

    2007-10-01

    The outcomes of the 19th Committee on Earth Observing Satellites (CEOS) Plenary held in London in November 2005, recognized that the CEOS Implementation Plan for Space-Based Observations for Global Earth Observation System of Systems (GEOSS) should: - identify the supply of space-based observations required to satisfy the requirements expressed by the 10-year implementation plan for GEOSS; and - propose an innovative process whereby the many disparate types of Earth observing programs funded by CEOS Member agencies might contribute to the supply of the required observations. The CEOS Task Force charged with drafting the CEOS Implementation Plan for Space-Based Observations for GEOSS focused its early efforts on the creation of a 'new planning process' which would satisfy the various criteria demanded by member space agencies, and which would hopefully encourage a new phase of specificity and focus in the multi-lateral co-operation efforts undertaken by space agencies under the CEOS umbrella - resulting in improved engagement of all CEOS Members and real implementation results. The CEOS Constellations is the title given to this new process, and four pilot studies have been initiated in order to pioneer and test the concept. The Japan Aerospace Exploration Agency (JAXA) and the National Aeronautics and Space Administration (NASA) were selected as the lead agencies for the study of the development of a CEOS Precipitation Constellation with the support of other CEOS space agency and user community participants. The goals, approach, and anticipated outcomes for the study will be discussed.

  14. Investigation of wax precipitation in crude oil: Experimental and modeling

    Directory of Open Access Journals (Sweden)

    Taraneh Jafari Behbahani

    2015-09-01

    Full Text Available In this work, a series of experiments were carried to investigation of rheological behavior of crude oil using waxy crude oil sample in the absence/presence of flow improver such as ethylene-vinyl acetate copolymer. The rheological data covered the temperature range of 5–30 °C. The results indicated that the performance of flow improver was dependent on its molecular weight. Addition of small quantities of flow improver, can improve viscosity and pour point of crude oil. Also, an Artificial Neural Network (ANN model using Multi-Layer Perceptron (MLP topology has been developed to account wax appearance temperature and the amount of precipitated wax and the model was verified using experimental data given in this work and reported in the literature. In order to compare the performance of the proposed model based on Artificial Neural Network, the wax precipitation experimental data at different temperatures were predicted using solid solution model and multi-solid phase model. The results showed that the developed model based on Artificial Neural Network can predict more accurately the wax precipitation experimental data in comparison to the previous models such as solid solution and multi-solid phase model with AADs less than 0.5%. Furthermore, the number of parameters required for the Artificial Neural Network (ANN model is less than the studied thermodynamic models.

  15. Monitoring measurements by the difference flow method during the year 2008. Drillholes OL-KR4 and OL-KR27

    International Nuclear Information System (INIS)

    Vaeisaesvaara, J.; Kristiansson, S.; Poellaenen, J.

    2009-08-01

    The Posiva Flow Log, Difference Flow Method (PFL DIFF) uses a flowmeter that incorporates a flow guide and can be used for relatively quick determinations of hydraulic conductivity and fresh water head in fractures/fractured zones in cored drillholes. This report presents the principles of the method and the results of measurements carried out in drillholes OL-KR4 and OL-KR27 at the Olkiluoto investigation site during the year 2008. These measurements are a part of the Olkiluoto monitoring programme. The section length of the flow guide in the flow logging measurements was either 2 m or 0.5 m. Flow into the drillhole or from the drillhole to the bedrock was measured within the section lengths and carried out in both pumped and natural (i.e. un-pumped) conditions. Calculations of the transmissivity (T) and the fresh water head (hfw) of the zones are shown in the results. The device used includes a sensor for single point resistance (SPR). SPR was measured in connection with flow measurements. The electrical conductivity (EC) of fracture-specific water was measured in chosen fractures in most of the drillholes. Fractures were selected on the basis of the measured flow from fracture to drillhole. In addition, some previously selected fractures were measured. The EC of the drillhole water was also measured. (orig.)

  16. Data Quality Objectives Summary Report for the 100-FR-1, 100-FR-2, 100-HR-1,100-KR-1, and 100-KR-2 Group 4 Waste Sites

    International Nuclear Information System (INIS)

    1997-10-01

    The 100-FR-1, 100-FR-2, 100-HR-1, 100-KR-1, and 100-KR-2 Group 4 waste sites will be the fourth set of Hanford 100 Area sites to undergo remediation. Like the sites in Groups 1, 2,and 3, the majority of Group 4 sties are considered high priority because of the contaminants present and their proximity to the Columbia River. the data quality objectives process,summarized in this document, is a U.S. Environmental Protection Agency approach for addressing data collecting and decision-making issues that are part of an environmental remediation project. The basic cleanup assumptions made in the Group 1, 2, and 3 designs are retained for the Group 4 design. As was the case with Group 3, the most significant difference between this DQO Summary Report and the Group 1 and 2 DQO Summary Reports is the data gaps that exist for specific Group 4 waste sites. These data gaps affect the approach to waste profiling and are the principal focus of the Group 4 DQO process

  17. Hydraulic Conductivity Measurements with HTU at Eurajoki, Olkiluoto, Borehole OL-KR15 and OL-KR15B, Year 2004

    Energy Technology Data Exchange (ETDEWEB)

    Haemaelaeinen, H.

    2005-07-01

    As a part of the site investigations for the disposal of spent nuclear fuel, hydraulic conductivity measurements were carried out in borehole OL-KR15 at Eurajoki, Olkiluoto. The objective was to investigate the distribution of the hydraulic conductivity in the surrounding bedrock volume. Measurements were carried out during 2003-2004 in two phases. The total length of the borehole OL-KR15 is 518,85 m and 158 45,14 m. Of the 471 ,5 m + 44,5 m total measurable length 414 m was covered with 237 standard tests with 2 m packer separation as specified in the research plan, partly with 1 m overlaps. 259 tests were initiated, but some of them ended to hardware or software errors or unsuitable parameter values. Double-packer constant-head method was used throughout with nominal 200 kPa overpressure. Injection stage lasted normally 20 minutes and fall-off stage 10 minutes. The tests were often shortened if there were clear indications that the hydraulic conductivity is below the measuring range of the system. The pressure in the test section was let to stabilise at least 5 min before injection. In some test sections the stabilisation or injection stage lasted several hours. Two transient (Horner and 1/Q) interpretations and one stationary-state (Moye) interpretation were made in-situ immediately after the test. The Hydraulic Testing Unit (HTU-system) is owned by Posiva Oy and it was operated by Geopros Oy. (orig.)

  18. The interference effects in the alignment and orientation of the Kr II 4p45p states following Kr I 3d9np resonance excitation

    International Nuclear Information System (INIS)

    Lagutin, B M; Petrov, I D; Sukhorukov, V L; Demekhin, Ph V; Zimmermann, B; Mickat, S; Kammer, S; Schartner, K-H; Ehresmann, A; Shutov, Yu A; Schmoranzer, H

    2003-01-01

    The energy dependence of the alignment parameter A 20 for the Kr II 4p 4 5p(E 1 J 1 ) states following excitation in the Raman regime with the exciting-photon energy passing through the Kr I 3dJ 9 barnpjbar resonances was investigated theoretically and experimentally. Interference between the resonance and direct photoionization channels explains the dependence of A 20 on the excitation energy. Experimentally, A 20 was determined after the analysis of 5p-5s fluorescence decay of the 4p 4 5p(E 1 J 1 ) states excited with monochromatized synchrotron radiation. The band pass of the synchrotron radiation was set to 10 meV which is smaller than the natural width of the 3d 9 np resonances (∼83 meV). Additionally, a strong energy dependence was predicted for the orientation parameter O 10 as well as for the angular distribution parameter of photoelectrons, β e , for several 4p 4 5p(E 1 J 1 ) ionic states

  19. Hydraulic Conductivity Measurements with HTU at Eurajoki, Olkiluoto, Borehole OL-KR15 and OL-KR15B, Year 2004

    International Nuclear Information System (INIS)

    Haemaelaeinen, H.

    2005-01-01

    As a part of the site investigations for the disposal of spent nuclear fuel, hydraulic conductivity measurements were carried out in borehole OL-KR15 at Eurajoki, Olkiluoto. The objective was to investigate the distribution of the hydraulic conductivity in the surrounding bedrock volume. Measurements were carried out during 2003-2004 in two phases. The total length of the borehole OL-KR15 is 518,85 m and 158 45,14 m. Of the 471 ,5 m + 44,5 m total measurable length 414 m was covered with 237 standard tests with 2 m packer separation as specified in the research plan, partly with 1 m overlaps. 259 tests were initiated, but some of them ended to hardware or software errors or unsuitable parameter values. Double-packer constant-head method was used throughout with nominal 200 kPa overpressure. Injection stage lasted normally 20 minutes and fall-off stage 10 minutes. The tests were often shortened if there were clear indications that the hydraulic conductivity is below the measuring range of the system. The pressure in the test section was let to stabilise at least 5 min before injection. In some test sections the stabilisation or injection stage lasted several hours. Two transient (Horner and 1/Q) interpretations and one stationary-state (Moye) interpretation were made in-situ immediately after the test. The Hydraulic Testing Unit (HTU-system) is owned by Posiva Oy and it was operated by Geopros Oy. (orig.)

  20. Nutritional quality of Krškopolje and commercial fattener pig meats in Slovenia

    Directory of Open Access Journals (Sweden)

    Milena Kovač

    2010-01-01

    Full Text Available The nutritional quality of M. Longissimus dorsi in the autochthonous Krškopolje pig breed and commercial fatteners from intensive Slovenian farms was compared. Commercial fatteners were divided into two groups according to lean meat percentage: MEATY and FATTY groups. The Krškopolje pigs (KK group and the FATTY group had higher intramuscular fat content than the MEATY group. The lowest saturated fatty acids (SFA proportion was found in the KK group and the highest in the FATTY group. The KK and FATTY groups contained higher proportions of monounsaturated fatty acids (MUFA as well as lower proportions of polyunsaturated fatty acids (PUFA compared to the MEATY group. The highest n-6 PUFA proportion was found in the MEATY group. The n-3 PUFA proportion differed between the MEATY and FATTY groups. The FATTY group had the lowest ratio of polyunsaturated to saturated fatty acids as well as the highest atherogenic index.

  1. Production of flat KrF laser focal profiles with echelon free-induced spatial incoherence

    International Nuclear Information System (INIS)

    Deniz, A.V.; Obenschain, S.P.; Pronko, M.; Lehmberg, R.H.

    1990-01-01

    High gain direct-drive laser fusion requires a uniform spherical pellet implosion. This in turn requires that the focal profile of each driving beam be sufficiently uniform and controlled. Several methods for producing uniform beams have been proposed. One promising technique, echelon free-induced spatial incoherence (ISI), consists of propagating a broadband spatially incoherent beam through an entire laser system. This technique will be used in the Nike laser, which is a twenty-four- to forty-eight-beam multikilojoule KrF system currently under construction at the Naval Research Laboratory (NRL). This paper presents measurements of focal profiles of laser light smoothed by echelon free ISI from a KrF oscillator and amplifier. The initial implementation is shown

  2. Assessment of bronchial provocation by sup(81m)Kr ventilation image in asthmatic children

    International Nuclear Information System (INIS)

    Sugimoto, Kazuo; Toba, Tsuyoshi; Uchiyama, Guio; Arimizu, Noboru.

    1982-01-01

    Allergen- or mediator-induced bronchospasm was studied by sup(81m)Kr ventilation image to determine it's sensitivity and safety as an assessment method. Twelve children with house dust sensitive asthma were subjected to inhalation of house dust, prostaglandin F sub(2α), or methacholine by ultrasonic nebulizer with sup(81m)Kr gas. During the examination dynamic ventilation images of both lungs were monitored on oscilloscope to see the changes in the ventilation images. This kind of provocation test has the following advantages compared to the conventional provocation tests. 1) There is no induction of severe attack by provocation when inhalation of antigen of mediator is stopped at the initiation of change on the ventilation image. 2) There is no overload to the patient as compared to the conventional provocation tests. 3) Analysis of the ventilation images stored in the computer can reveal the area of ventilation disturbance in the lung and the changes can be expressed quantitatively. (author)

  3. KrF laser cost/performance model for ICF commercial applications

    International Nuclear Information System (INIS)

    Harris, D.B.; Pendergrass, J.H.

    1985-01-01

    Simple expressions suitable for use in commercial-applications plant parameter studies for the direct capital cost plus indirect field costs and for the efficiency as a function of repetition rate were developed for pure-optical-compression KrF laser fusion drivers. These simple expressions summarize estimates obtained from detailed cost-performance studies incorporating recent results of ongoing physics, design, and cost studies. Contributions of KrF laser capital charges and D and M costs to total levelized constant-dollar (1984) unit ICF power generation cost are estimated as a function of plant size and driver pulse energy using a published gain for short-wavelength lasers and representative values of plant parameters

  4. The production of *sp81m*Kr generators at the Oslo cyclotron

    International Nuclear Information System (INIS)

    Bjroenstad, T.; Holtebekk, T.; Ruud, A.

    1984-01-01

    The techniques developed for the production of *sp81m*Kr(13s) ventilation generators at the Oslo cyclotron are described. The procedure is based on the reaction *sp82*Kr(p,2n)*sp81*Rb using krypton gas of natural composition as target. The target chamber is designed for a gas pressure of 10 bar. The production unit is dimensioned for a parallel production of five generators, but this number may easily be increased. Attention is drawn to the fact that *sp81m*Rb(31 min) is produced in about the same amount as the *sp81*Rb (4.57 h) ground state. The consequences for the calibration procedure is discussed. Routine production has been exerted without major difficulties for nearly 1.5 years. The procedure has proven to be inexpensive and reliable. (Auth.)

  5. The Triassic metabasalts of Dudin Krš, near Kosovska Mitrovica, Serbia

    Directory of Open Access Journals (Sweden)

    Memović Emin

    2003-01-01

    Full Text Available This paper presents the geochemical characteristics of the metabasalts of Dudin Krš, near Kosovska Mitrovica. The Dudin Krš is the easternmost occurrence of Middle Triassic rift-related volcanic rocks in the Dinarides. Generally, these rocks show similarities to other Triassic volcanic rocks of the Dinarides. They are high-magnesian, ol and ne-normative basalts, with low Zr/Nb and medium/low Ti/Zr and Ti/Y ratios. They exhibit transitional geochemical characteristics, between E-MORB and subalkaline basalts of continental rift zones. Their presence and geochemical affinity is evidence of rifting processes along the continental slope of the Adria block during Middle Triassic.

  6. Phase formation in Zr/Fe multilayers during Kr ion irradiation

    International Nuclear Information System (INIS)

    Motta, A. T.

    1998-01-01

    A detailed study has been conducted of the effect of Kr ion irradiation on phase formation in Zr-Fe metallic multilayers, using the Intermediate Voltage Electron Microscopy (IVEM) at Argonne National Laboratory. Metallic multilayers were prepared with different overall compositions (near 50-50 and Fe-rich), and with different wavelengths (repetition thicknesses). These samples were irradiated with 300 keV Kr ions at various temperatures to investigate the final products, as well as the kinetics of phase formation. For the shorter wavelength samples, the final product was in all cases an amorphous Zr-Fe phase, in combination with Fe, while specially for the larger wavelength samples, in the Fe-rich samples the intermetallic compounds ZrFe 2 and Zr 3 Fe were formed in addition to the amorphous phase. The dose to full reaction decreases with temperature, and with wavelength in a manner consistent with a diffusion-controlled reaction

  7. The Nike KrF laser facility: Performance and initial target experiments

    Science.gov (United States)

    Obenschain, S. P.; Bodner, S. E.; Colombant, D.; Gerber, K.; Lehmberg, R. H.; McLean, E. A.; Mostovych, A. N.; Pronko, M. S.; Pawley, C. J.; Schmitt, A. J.; Sethian, J. D.; Serlin, V.; Stamper, J. A.; Sullivan, C. A.; Dahlburg, J. P.; Gardner, J. H.; Chan, Y.; Deniz, A. V.; Hardgrove, J.; Lehecka, T.; Klapisch, M.

    1996-05-01

    Krypton-fluoride (KrF) lasers are of interest to laser fusion because they have both the large bandwidth capability (≳THz) desired for rapid beam smoothing and the short laser wavelength (1/4 μm) needed for good laser-target coupling. Nike is a recently completed 56-beam KrF laser and target facility at the Naval Research Laboratory. Because of its bandwidth of 1 THz FWHM (full width at half-maximum), Nike produces more uniform focal distributions than any other high-energy ultraviolet laser. Nike was designed to study the hydrodynamic instability of ablatively accelerated planar targets. First results show that Nike has spatially uniform ablation pressures (Δp/pNike laser in producing uniform illumination, and its performance in correspondingly uniform acceleration of targets.

  8. Laser-plasma source parameters for Kr, Gd, and Tb ions at 6.6 nm

    Energy Technology Data Exchange (ETDEWEB)

    Masnavi, Majid; Szilagyi, John; Parchamy, Homaira; Richardson, Martin C. [The Townes Laser Institute, College of Optics and Photonics, University of Central Florida, 4000 Central Florida Blvd., Orlando, Florida 32816 (United States)

    2013-04-22

    There is increasing interest in extreme-ultraviolet (EUV) laser-based lamps for sub-10-nm lithography operating in the region of 6.6 nm. A collisional-radiative model is developed as a post-processor of a hydrodynamic code to investigate emission from resonance lines in Kr, Gd, and Tb ions under conditions typical for mass-limited EUV sources. The analysis reveals that maximum conversion efficiencies of Kr occur at 5 Multiplication-Sign 10{sup 10}W/cm{sup 2}, while for Gd and Tb it was Asymptotically-Equal-To 0.9%/2{pi}sr for laser intensities of (2-5) Multiplication-Sign 10{sup 12}W/cm{sup 2}.

  9. Extended calculations of energies, transition rates, and lifetimes for F-like Kr XXVIII

    Science.gov (United States)

    Zhang, C. Y.; Si, R.; Yao, K.; Gu, M. F.; Wang, K.; Chen, C. Y.

    2018-02-01

    The excitation energies, lifetimes, wavelengths and E1, E2, M1 and M2 transition rates for the lowest 389 levels of the 2l7, 2l63l‧, 2l64l‧, and 2l65l‧ configurations from second-order many-body perturbation theory (MBPT) calculations, and the results for the lowest 200 states of the 2l7, 2l63l‧, and 2l64l‧ configurations from multi-configuration Dirac-Hartree-Fock (MCDHF) calculations in F-like Kr XXVIII are presented in this work. The relative differences between our two sets of level energies are mostly within 0.005% for the lowest 200 levels. Comparisons are made with experimental and other available theoretical results to assess the reliability and accuracy of the present calculations. We believe them to be the most complete and accurate results for Kr XXVIII at present.

  10. Precipitation in the Solar System

    Science.gov (United States)

    McIntosh, Gordon

    2007-01-01

    As an astronomy instructor, I am always looking for commonly observed Earthly experiences to help my students and me understand and appreciate similar occurrences elsewhere in the solar system. Recently I wrote a short TPT article on frost. This paper is on the related phenomena of precipitation. Precipitation, so common on most of the Earth's…

  11. Design and performance of large area monolithic electron guns for the Aurora KrF laser system

    International Nuclear Information System (INIS)

    Kang, M.; Rosocha, L.A.; Romero, V.O.; Van Haaften, F.W.; Brucker, J.P.

    1985-01-01

    Aurora is an inertial confinement fusion laser system using optical angular multiplexing and a chain of four cold cathode electron beam driven KrF laser amplifiers to produce 10 to 20 kJ of optical energy

  12. Rezension: Ada Lovelace. Die Pionierin der Computertechnik und ihre Nachfolgerinnen von Sybille Krämer (Hg.)

    OpenAIRE

    Bettina Schabschneider

    2015-01-01

    Ein aktueller von Sybille Krämer herausgegebener Sammelband beleuchtet die Bedeutung der Computertechnik-Pionierin Ada Lovelace. Bettina Schabschneider hat den Band einer detaillierten Lektüre unterzogen und für die MEDIENIMPULSE rezensiert …

  13. Sc-45 nuclear magnetic resonance analysis of precipitation in dilute Al-Sc alloys

    NARCIS (Netherlands)

    Celotto, S; Bastow, TJ

    Nuclear magnetic resonance (NMR) with Sc-45 is used to determine the solid solubility of scandium in aluminium and to follow the precipitation of Al3Sc during the ageing of an Al-0.06 at.% Sc alloy via the two fully resolved peaks, corresponding to Sc in the solid solution Al matrix and to Sc in the

  14. Solid waste

    International Nuclear Information System (INIS)

    1995-01-01

    The article drawn up within the framework of 'the assessment of the state of the environment in Lebanon' provides an overview of solid waste management, and assesses future wastes volume and waste disposal issues.In particular it addresses the following concerns: - Long term projections of solid waste arisings (i.e. domestic, industrial, such commercial wastes, vehicle types, construction waste, waste oils, hazardous toxic wastes and finally hospital and clinical wastes) are described. - Appropriate disposal routes, and strategies for reducing volumes for final disposal - Balance between municipal and industrial solid waste generation and disposal/treatment and - environmental impacts (aesthetics, human health, natural environment )of existing dumps, and the potential impact of government plans for construction of solid waste facilities). Possible policies for institutional reform within the waste management sector are proposed. Tables provides estimations of generation rates and distribution of wastes in different regions of Lebanon. Laws related to solid waste management are summarized

  15. Kinetics of cadmium hydroxide precipitation

    International Nuclear Information System (INIS)

    Patterson, J.W.; Marani, D.; Luo, B.; Swenson, P.

    1987-01-01

    This paper presents some preliminary results on the kinetics of Cd(OH)/sub 2/ precipitation, both in the absence and the presence of citric acid as an inhibiting agent. Batch and continuous stirred tank reactor (CSTR) precipitation studies are performed by mixing equal volumes of NaOH and Cd(NO/sub 3/)/sub 2/ solutions, in order to avoid localized supersaturation conditions. The rate of metal removal from the soluble phase is calculated from the mass balance for the CSTR precipitation tests. In addition, precipitation kinetics are studied in terms of nucleation and crystal growth rates, by means of a particle counter that allows a population balance analysis for the precipitation reactor at steady state conditions

  16. Encoding information into precipitation structures

    International Nuclear Information System (INIS)

    Martens, Kirsten; Bena, Ioana; Droz, Michel; Rácz, Zoltan

    2008-01-01

    Material design at submicron scales would be profoundly affected if the formation of precipitation patterns could be easily controlled. It would allow the direct building of bulk structures, in contrast to traditional techniques which consist of removing material in order to create patterns. Here, we discuss an extension of our recent proposal of using electrical currents to control precipitation bands which emerge in the wake of reaction fronts in A + + B – → C reaction–diffusion processes. Our main result, based on simulating the reaction–diffusion–precipitation equations, is that the dynamics of the charged agents can be guided by an appropriately designed time-dependent electric current so that, in addition to the control of the band spacing, the width of the precipitation bands can also be tuned. This makes straightforward the encoding of information into precipitation patterns and, as an amusing example, we demonstrate the feasibility by showing how to encode a musical rhythm

  17. Modeling the energy deposition in the Aurora KrF laser amplifier chain

    International Nuclear Information System (INIS)

    Comly, J.C.; Czuchlewski, S.J.; Greene, D.P.; Hanson, D.E.; Krohn, B.J.; McCown, A.W.

    1988-01-01

    Monte Carlo calculations model the energy depositions by highly energetic electron beams into the cavities of the four KrF laser amplifiers in the Aurora chain. Deposited energy density distributions are presented and studied as functions of e-beam energy and gas pressure. Results are useful for analyzing small signal gain (SSG) measurements and optimizing deposition in future experiments. 7 refs., 7 figs., 1 tab

  18. Rotational excitation of linear triatomic molecules: Ar, Kr + N2O, CO2

    International Nuclear Information System (INIS)

    Farrar, J.M.; Parson, J.M.; Lee, Y.T.

    1974-01-01

    Rotational excitation of N 2 O and CO 2 in collisions with Ar and Kr has been studied by crossing two supersonic molecular beams and detecting scattered products with a mass spectrometer. Measurement of the time of flight spectrum of the products as a function of laboratory scattering angle theta indicates that the inelasticity is concentrated in the forward direction in the center of mass system. Difference between CO 2 and N 2 O are discussed briefly

  19. Aurora: Los Alamos multikilojoule angular-multiplexed KrF driver prototype for ICF

    International Nuclear Information System (INIS)

    Rosocha, L.A.; Hanlon, J.A.; McLeod, J.

    1987-01-01

    The Los Alamos National Laboratory (LANL) has participated in programs to apply high-power gas lasers to inertial confinement fusion (ICF). The bulk of this effort has been in the development of CO/sub 2/ laser systems and laser-plasma interaction experiments at a 10.6-μm wavelength. The main hardware element in this program is the Aurora KrF laser system, which is a prototype for using optical angular multiplexing and serial amplification by large electron-beam-driven KrF laser amplifiers to study KrF systems as potential fusion drivers. Aurora will serve as a test-bed for specific laser, optical, and electron-beam-pumping technology aspects of larger KrF fusion systems. The Aurora system is being built in two phases. The first-phase portion of the Aurora system contains all the main optical and laser elements from the front end to the final amplifier output. In the first phase, the front end output is replicated using aperture slicers and beam splitters to produce a 480-ns long pulse train consisting of 96 separate 5-ns pulses. This pulse train is encoded in angular separation, relayed through the amplifier chain by means of the centered optical system and the computer-controlled alignment station, and delivered to a diagnostic station which follows the main power amplifier [large aperture module (LAM)]. The second phase of the system contains the first-phase portion and the additional optical and target hardware needed to stack 48 of the 96 multiplexed and amplified beams into a single multikilojoule 5-ns pulse at the fusion target. The authors give a description of the Aurora system and discuss its present status

  20. X-ray imaging of targets irradiated by the Nike KrF laser

    International Nuclear Information System (INIS)

    Brown, C.; Seely, J.; Feldman, U.; Obenschain, S.; Bodner, S.; Pawley, C.; Gerber, K.; Serlin, V.; Sethian, J.; Aglitskiy, Y.; Lehecka, T.; Holland, G.

    1997-01-01

    Foil targets irradiated by the Naval Research Laboratory Nike KrF laser were imaged in the x-ray region with two-dimensional spatial resolution in the 2 endash 10 μm range. The images revealed the smoothness of the emission from target and backlighter foils, the acceleration of the target foils, and the growth of Rayleigh endash Taylor instabilities that were seeded by patterns on the irradiated sides of CH foils

  1. Cross-Border Region Králíky - Międzylesie

    Czech Academy of Sciences Publication Activity Database

    Vaishar, Antonín; Cetkovský, Stanislav; Martinát, Stanislav; Nosková, Helena; Zapletalová, Jana

    2007-01-01

    Roč. 15, č. 2 (2007), s. 40-54 ISSN 1210-8812 R&D Projects: GA MŠk 2D06001 Institutional research plan: CEZ:AV0Z30860518; CEZ:AV0Z80630520 Keywords : cross-border region * periphery * regional development * Králíky * Międzylesie Subject RIV: DE - Earth Magnetism, Geodesy, Geography

  2. Demonstration of a bronchopleural communication by inhalation of Kr-81m gas

    International Nuclear Information System (INIS)

    Vincken, W.; Schandevyl, W.; Sonstabo, R.; Bossuyt, A.

    1981-01-01

    Suspicion of a persisting communication between the bronchial tree and the pleural space in a patient with surgically drained pneumothorax was confirmed by the inhalation of Kr-81m gas. Compared to other diagnostic methods, this technique is harmless and repeatable, and hence very convenient for the assessment and follow-up of persisting pneumothorax due to air-leaks and of bronchopleural fistulas of any cause

  3. Site-specific waste management instruction for the 100-KR-4 Operable Unit drilling

    International Nuclear Information System (INIS)

    Hadley, J.T.

    1996-07-01

    This site-specific waste management instruction provides guidance for the management of waste generated as a result of groundwater well installations in the 100-KR-4 Operable Unit (OU). The well installations are necessary to implement the Remedial Action (RA) option (pump-and-treat using ion exchange) to prevent discharge of hexavalent chromium at levels above those considered protective of aquatic life in the Columbia River and riverbed sediments

  4. Site-specific waste management instruction for the 100-KR-4 Operable Unit drilling. Revision 1

    International Nuclear Information System (INIS)

    Hadley, J.T.

    1996-08-01

    This site-specific waste management instruction provides guidance for the management of waste generated as a result of groundwater well installations in the 100-KR-4 Operable Unit (OU). The well installations are necessary to implement the Remedial Action (RA) option (pump-and-treat using ion exchange) to prevent discharge of hexavalent chromium at levels above those considered protective of aquatic life in the Columbia River and riverbed sediments

  5. Separation of 85Kr from the off-gases of reprocessing plants

    International Nuclear Information System (INIS)

    1975-01-01

    Going from the aspect of keeping the radiation exposure to the population as small as possible, the following is recommended: 1) Skin dose of maximum 10 mrem/a, global exposure maximum 10 6 Ci/a; 2) decontamination factor of >= 100; 3) storage of separated 85 Kr in pressure gas bottles, sinking in deap sea; 4) test-sinking in agreement with international panel. (HP/LH) [de

  6. Feasibility of 81Br(nu,e-)81Kr solar neutrino experiment

    International Nuclear Information System (INIS)

    Hurst, G.S.; Allman, S.L.; Chen, C.H.; Kramer, S.D.; Thomson, J.O.; Cleveland, B.

    1985-05-01

    Several ingenious solutions have been offered for the solar neutrino problem - a defect in the solar model, the appearance of a new type of neutrino physics, the sun is no longer burning, etc. The range of these proffered solutions stresses the need for a new experiment to study the sun. The modern pulsed laser now makes possible a new solar neutrino test which examines an independent neutrino source in the sun. A recently proposed experiment would use the reaction 81 Br(nu,e - ) 81 Kr to measure the flux of 7 Be neutrinos from the sun. When 7 Be decays by electron capture to make 7 Li, a neutrino is emitted at 0.862 MeV and the flux of these on the earth is about 4 x 10 9 cm -2 s -1 , according to the standard model. Therefore, an experiment based on 81 Br(nu,e - ) 81 Kr which is sensitive to these lower energy neutrinos would be of fundamental importance. To first order, the chlorine experiment detects the 8 B neutrinos while bromine detects the much more abundant 7 Be neutrino source. In practice, the proposed bromine experiment would be very similar to the chlorine radiochemical experiment, except that 81 Kr with a half-life of 2 x 10 5 years cannot be counted by decay methods. With an experiment of about the same volume as the chlorine experiment (380 m 3 ) filled with CH 2 Br 2 , the model predicts about 2 atoms of 81 Kr per day. The bromine experiment depends entirely on the RIS method, implemented with pulsed lasers, for its success. 10 refs., 3 figs

  7. Data validation report for the 100-KR-4 operable unit first quarter, 1994

    International Nuclear Information System (INIS)

    Krug, A.D.

    1994-01-01

    Samples were obtained from the 100-KR-4 Operable Unit first Quarter 1994 Groundwater Sampling event. The data from the chemical analysis of fifty-eight samples from this sampling event and their related quality assurance samples were reviewed and validated to verify that reported samples results were of sufficient quality to support decisions regarding remedial actions performed at this site. Information fro the sampling event and the information validation processes are presented in this document

  8. Archaeological finds from the vaulted building at Krševica

    Directory of Open Access Journals (Sweden)

    Popović Petar

    2008-01-01

    Full Text Available The completely preserved building with barrel vault was discovered in 2008 in the course of investigation of the remains of an urban settlement dating from the 4th /3rd centuries BC at the site Kale in the village Krševica (southeast Serbia. We are presenting in this work the archaeological finds discovered in this structure. They included pottery, worked stone and many skeletons of horses and dogs that are assumed to be the ritual sacrifice.

  9. Study of subthreshold pion mesons of 86Kr + 197Au reaction

    International Nuclear Information System (INIS)

    Ma Yugang; Shen Wenqing; Ge Lingxiao; Zhan Wenlong; Wang Bing; Zhu Yongtai; Feng Jun; Zeng Yaowu; Guo Zhongyan; Zhou Jianqun

    1991-01-01

    Authors investigated the subthreshold pions multiplicity for 86 Kr + 197 Au system in non-relativistic BUU frame. The aims were to obtain some qualitative conclusions about pions production and absorption process. Because the production of pions and other energetic particles are a very complicated problem in HIC, nowadays a full self-consistent and effective theoretical approach has not yet been presented, the more detail and further research work must be done

  10. Rukopis královédvorský a ohlas Písně o Nibelunzích

    Czech Academy of Sciences Publication Activity Database

    Krejčová, Iva

    2010-01-01

    Roč. 58, č. 4 (2010), s. 425-443 ISSN 0009-0468 Institutional research plan: CEZ:AV0Z90560517 Keywords : Czech National Revival * Nibelungenlied * The Song of the Nibelungs * Rukopis královédvorský * Manuscript of Dvůr Králové * echo * literary imagery * romantism * myth * Tacitus, Gaius Cornelius * Herder, Johann Gottfried Subject RIV: AJ - Letters, Mass-media, Audiovision

  11. Application of Kr-81m gas for chronic obstructive pulmonary disease. A comparison of various inhalation techniques

    Energy Technology Data Exchange (ETDEWEB)

    Kawakami, K; Katsuyama, N i; Anno, I i; Harada, J; Kuroda, T [Jikei Univ., Tokyo (Japan). School of Medicine

    1978-11-01

    The Kr-81m ventilation study was performed by the following four inhalation techniques. 1) Spontaneous respiration with Kr-81m in air (Sp). 2) Serial inhalation of Kr-81m from residual volume to total lung capacity (VC). 3) Bolus inhalation of 50 ml of Kr-81m from the level of functional residual capacity (FRC), and 4) residual volume (RV), followed by air, to total lung capacity. Scintiphotos were taken during 10 sec of breathholding for VC, FRC, RV inhalation techniques and during tidal breathing for Sp technique, in a sitting position, by a scinticamera (Pho/Gamma HP). Twenty-three of the 28 subjects showed uneven distribution of the washout time in the Xe-133 study, 5 cases have a normal Xe-133 study. In severe obstructive changes with marked delay of the Xe-133 washout time, inhalation defects of Kr-81m were imaged in all techniques. In minor degrees of obstruction associated with slight delay of the washout, FRC and RV techniques detected abnormalities, whilst images by Sp and VC techniques showed homogeneous distribution of Kr-81m. This is due to rebreathing effect on Sp and to opening of partial airway obstruction in a high lung volume on VC technique. RV technique had a disadvantage for imaging of abnormalities in the lower lung fields, because Kr-81m concentration is low in the lower lung fields, due to physiological closure of the small airway. In 3 of 5 cases of asymptomatic asthma with a normal Xe-133 study, uneven distribution in RV technique was the only abnormality detected. FRC technique was most sensitive for slight obstructive changes in the upper lung fields as well as in the lower. For the ventilation study using Kr-81m, a combined test of Sp, VC, RV and FRC inhalation techniques is useful for early detection of the small airway disease and evaluation of the degree of abnormalities.

  12. Measurements of fusion cross sections in the systems {sup 58,64}Ni +, {sup 78,86}Kr

    Energy Technology Data Exchange (ETDEWEB)

    Rehm, K.E.; Jiang, C.L.; Esbensen, H. [and others

    1995-08-01

    We investigated the nuclear structure dependence of the sub-barrier fusion enhancement in heavy-ion induced reactions by studying the systems {sup 58,64}Ni + {sup 78,86}Kr at energies in the vicinity of the Coulomb barrier. These {sup 78,86}Kr selected because, similar to the Mo case discussed isotopes were above, there are strong changes in nuclear structure as a function of the neutron number. However, contrary to Mo, where the {open_quotes}softness{close_quotes} of the nucleus increases with higher neutron number, the most collective nucleus for the Kr case is the neutron-deficient {sup 78}Kr. The experiment was performed with Kr beams from the positive-ion injector using enriched {sup 78,86}Kr gas in the ECR ion source. The separation of evaporation residues from the elastically-scattered particles was achieved by using their difference in time-of-flight and magnetic rigidity in the gas-filled spectrograph. The excitation functions for the four systems were compared to coupled-channels calculations including inelastic excitations of one- and two-phonon states in projectile and target. For systems involving {sup 86}Kr, good agreement between theory and experiment is obtained, while for {sup 78}Kr + {sup 58,64}Ni an additional enhancement of the cross sections persisted at the lowest energies. It was found that this fusion enhancement correlates with the nuclear structure of the individual nucleus. Characterizing the structure of vibrational even-even nuclei by their restoring force parameter C{sub 2}, which can be calculated from the energy of the lowest 2{sup +} state and the associated B(E2) value, one observes that nuclei with small C{sub 2} values exhibit a large sub-barrier fusion enhancement, while nuclei with high values of C{sub 2} (usually closed-shell nuclei), show smaller fusion yields.

  13. Transitions in Al-like, Mg-like and Na-like Kr and Mo, observed in the JET tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Jupen, C; Denne, B; Martinson, I [JET Joint Undertaking, Abingdon, Oxon (UK)

    1990-05-01

    Spectra of highly ionized Kr and Mo, emitted from the JET tokamak plasmas, have been recorded in the region 30-335 A. Detailed analysis of the n=3, {Delta}n=0 transitions in Kr XXIV-XXVI and Mo XXX-XXXII has resulted in a number of new spectral classifications. Some isoelectronic regularities for Al-like and Mg-like ions are discussed. (orig.).

  14. A new technique for production of yellow cake with double precipitation

    International Nuclear Information System (INIS)

    Li Jianhua; Zeng Yijun; Li Shangyuan; Kong Guiying

    1997-01-01

    The author presents a new technique for production of yellow cake with double precipitation, thus solving a series of problems for precipitating uranium with traditional double precipitation. The new technique can not only remove ferric ions and sulfate radicals but also make solid-liquid separation easy, utilize effectively the sulfuric acid produced in ferric ions precipitation process, and increase uranium concentration of leaching liquor. To take it as producing yellow cake will save investment, simplify operation, and cut down the consumption of raw materials and energies. It is more competitive than ion-exchange or solvent extraction in the process of extracting-purifying and preparing yellow cake

  15. Negligible fractionation of Kr and Xe isotopes by molecular diffusion in water

    Science.gov (United States)

    Tyroller, Lina; Brennwald, Matthias S.; Busemann, Henner; Maden, Colin; Baur, Heinrich; Kipfer, Rolf

    2018-06-01

    Molecular diffusion is a key transport process for noble gases in water. Such diffusive transport is often thought to cause a mass-dependent fractionation of noble gas isotopes that is inversely proportional to the square root of the ratio of their atomic mass, referred to as the square root relation. Previous studies, challenged the commonly held assumption that the square root relation adequately describes the behaviour of noble gas isotopes diffusing through water. However, the effect of diffusion on noble gas isotopes has only been determined experimentally for He, Ne and Ar to date, whereas the extent of fractionation of Kr and Xe has not been measured. In the present study the fractionation of Kr and Xe isotopes diffusing through water immobilised by adding agar was quantified through measuring the respective isotope ratio after diffusing through the immobilised water. No fractionation of Kr and Xe isotopes was observed, even using high-precision noble gas analytics. These results complement our current understanding on isotopic fractionation of noble gases diffusing through water. Therefore this complete data set builds a robust basis to describe molecular diffusion of noble gases in water in a physical sound manner which is fundamental to assess the physical aspects of gas dynamics in aquatic systems.

  16. Aurora: A short-pulse multikilojoule KrF inertial fusion laser system

    International Nuclear Information System (INIS)

    Rosocha, L.A.

    1985-01-01

    Aurora is a laser system that serves as an operating technology demonstration prototype for large-scale high-energy KrF laser systems of interest for inertial fusion applications. This system will incorporate the following elements to achieve an end-to-end 248-nm laser fusion concept demonstration: an injection-locked oscillator-amplifier front end; an optical angular multiplexer to produce 96 encoded optical channels each of 5-nsec duration; a chain of four electron-beam-driven KrF laser amplifiers; automated alignment systems for beam alignment; a decoder to provide for pulse compression of some fraction of the total beam train to be delivered to target, and a target chamber to house and diagnose fusion targets. The front end configuration uses a stable resonator master oscillator to drive an injection-locked unstable resonator slave oscillator. An extension of existing technology has been used to develop an electrooptic switchout at 248 nm that produces a 5-nsec pulse from the longer slave oscillator pulse. This short pulse is amplified by a postamplifier. Using these discharge lasers, the front end then delivers at least 250 mJ of KrF laser light output to the optical encoder

  17. Shape study of the N=Z waiting-point nucleus 72Kr via beta decay

    CERN Document Server

    Briz Monago, Jose Antonio; Nácher González, Enrique

    The Ph.D. thesis entitled “Shape study of the N=Z waiting-point nucleus 72Kr via beta decay” is devoted to the study of the shape of the ground state of the 72Kr nucleus. It is an N=Z nucleus in the mass region A~70-80 where shape transitions and the shape coexistence phenomena have been identified. Furthermore, this nucleus participates in the rp-process as a waiting point due to the slowdown of the process taking place at the arrival to this nucleus. The study of the properties of this nucleus is interesting from the Nuclear Structure point of view, for the phenomena occurring in its mass region and have been predicted for it, and from the Nuclear Astrophysics for the accurate performance of astrophysical calculations. The β+/EC decay of the 72Kr nucleus has been studied through two complementary experiments at the ISOLDE facility at CERN in Geneva (Switzerland). In one of them, the low-spin structure of the daughter nucleus, 72Br, has been revised via conversion electron spectroscopy where the convers...

  18. Cryogenics free production of hyperpolarized 129Xe and 83Kr for biomedical MRI applications

    Science.gov (United States)

    Hughes-Riley, Theodore; Six, Joseph S.; Lilburn, David M. L.; Stupic, Karl F.; Dorkes, Alan C.; Shaw, Dominick E.; Pavlovskaya, Galina E.; Meersmann, Thomas

    2013-12-01

    As an alternative to cryogenic gas handling, hyperpolarized (hp) gas mixtures were extracted directly from the spin exchange optical pumping (SEOP) process through expansion followed by compression to ambient pressure for biomedical MRI applications. The omission of cryogenic gas separation generally requires the usage of high xenon or krypton concentrations at low SEOP gas pressures to generate hp 129Xe or hp 83Kr with sufficient MR signal intensity for imaging applications. Two different extraction schemes for the hp gasses were explored with focus on the preservation of the nuclear spin polarization. It was found that an extraction scheme based on an inflatable, pressure controlled balloon is sufficient for hp 129Xe handling, while 83Kr can efficiently be extracted through a single cycle piston pump. The extraction methods were tested for ex vivo MRI applications with excised rat lungs. Precise mixing of the hp gases with oxygen, which may be of interest for potential in vivo applications, was accomplished during the extraction process using a piston pump. The 83Kr bulk gas phase T1 relaxation in the mixtures containing more than approximately 1% O2 was found to be slower than that of 129Xe in corresponding mixtures. The experimental setup also facilitated 129Xe T1 relaxation measurements as a function of O2 concentration within excised lungs.

  19. Cryogenics free production of hyperpolarized 129Xe and 83Kr for biomedical MRI applications☆

    Science.gov (United States)

    Hughes-Riley, Theodore; Six, Joseph S.; Lilburn, David M.L.; Stupic, Karl F.; Dorkes, Alan C.; Shaw, Dominick E.; Pavlovskaya, Galina E.; Meersmann, Thomas

    2013-01-01

    As an alternative to cryogenic gas handling, hyperpolarized (hp) gas mixtures were extracted directly from the spin exchange optical pumping (SEOP) process through expansion followed by compression to ambient pressure for biomedical MRI applications. The omission of cryogenic gas separation generally requires the usage of high xenon or krypton concentrations at low SEOP gas pressures to generate hp 129Xe or hp 83Kr with sufficient MR signal intensity for imaging applications. Two different extraction schemes for the hp gasses were explored with focus on the preservation of the nuclear spin polarization. It was found that an extraction scheme based on an inflatable, pressure controlled balloon is sufficient for hp 129Xe handling, while 83Kr can efficiently be extracted through a single cycle piston pump. The extraction methods were tested for ex vivo MRI applications with excised rat lungs. Precise mixing of the hp gases with oxygen, which may be of interest for potential in vivo applications, was accomplished during the extraction process using a piston pump. The 83Kr bulk gas phase T1 relaxation in the mixtures containing more than approximately 1% O2 was found to be slower than that of 129Xe in corresponding mixtures. The experimental setup also facilitated 129Xe T1 relaxation measurements as a function of O2 concentration within excised lungs. PMID:24135800

  20. KrF excimer laser precision machining of hard and brittle ceramic biomaterials

    International Nuclear Information System (INIS)

    Huang, Yao-Xiong; Lu, Jian-Yi; Huang, Jin-Xia

    2014-01-01

    KrF excimer laser precision machining of porous hard–brittle ceramic biomaterials was studied to find a suitable way of machining the materials into various desired shapes and sizes without distorting their intrinsic structure and porosity. Calcium phosphate glass ceramics (CPGs) and hydroxyapatite (HA) were chosen for the study. It was found that KrF excimer laser can cut both CPGs and HA with high efficiency and precision. The ablation rates of CPGs and HA are respectively 0.081 µm/(pulse ⋅ J cm −2 ) and 0.048 µm/(pulse ⋅ J cm −2 ), while their threshold fluences are individually 0.72 and 1.5 J cm −2 . The cutting quality (smoothness of the cut surface) is a function of laser repetition rate and cutting speed. The higher the repetition rate and lower the cutting speed, the better the cutting quality. A comparison between the cross sections of CPGs and HA cut using the excimer laser and using a conventional diamond cutting blade indicates that those cut by the excimer laser could retain their intrinsic porosity and geometry without distortion. In contrast, those cut by conventional machining had distorted geometry and most of their surface porosities were lost. Therefore, when cutting hard–brittle ceramic biomaterials to prepare scaffold and implant or when sectioning them for porosity evaluation, it is better to choose KrF excimer laser machining. (paper)

  1. Effect of swift heavy Kr ions on complex permittivity of silicon PIN diode

    International Nuclear Information System (INIS)

    Li, Yun; Su, Ping; Yang, Zhimei; Ma, Yao; Gong, Min

    2016-01-01

    Highlights: • The complex permittivity has been studied on Si PIN irradiated by heavy Kr ions. • DLTS was used to investigate damages formed in PIN diode during irradiation. • The recombination of carriers has important influence on the complex permittivity. - Abstract: The complex permittivity has been researched on silicon PIN diodes irradiated by 2150 MeV heavy Kr ions in this article. The difference of complex permittivity spectra from 1 to 10^7 Hz between irradiated and unirradiated were observed and discussed. The current-voltage (I-V) and capacitance-voltage (C-V) characteristics were measured at room temperature (300 K) to study the change of electrical properties in diode after irradiation. Deep level transient spectroscopy (DLTS) was used to investigate damages caused by 2150 MeV heavy Kr ions in diode. Two extra electron traps were observed, which were located at E C -0.31 eV and E C -0.17 eV. It indicated that new defects have been formed in PIN diode during irradiation. A comparison of the results illustrated that not only the carrier density but also the recombination of electron-hole pair have important influences on the properties of complex permittivity. These results offer a further indication of the mechanism about the complex permittivity property of semiconductor device, which could help to make the applications for the semiconductor device controlled by electric signals come true in the fields of optoelectronic integrated circuits, plasma antenna and so on.

  2. Influence of damage caused by Kr ions and neutrons on electrical properties of silicon detectors

    CERN Document Server

    Croitoru, N; Rancoita, P G; Rattaggi, M; Seidman, A

    1999-01-01

    In this paper, new measurements of physical properties of high-resistivity silicon, used in high-energy detectors, are presented. The obtained data contribute to the understanding of the causes which damage the 2electronic characteristics of the detection systems under irradiation of neutrons and ionized particles (Kr). The Hall effect coefficient (R sub H) and resistivity (rho) measurements as a function of temperature (T), for non-irradiated and irradiated by neutrons and Kr ions, were performed. The measurements of the Hall coefficient and resistivity of non-irradiated samples and irradiated at neutron fluences (PHI=9.9x10 sup 1 sup 0 n/cm sup 2 (neutrons) and PHI>=7.5x10 sup 8 Kr/cm sup 3 (ions), cannot be explained, considering the usual theoretical relations. The results, obtained in these experiments, have shown a change of mechanism of conduction due to the damaged regions, where localized levels are created, which are the main cause of the deviation of the electrical characteristics of the detectors ...

  3. Shape evolution of 72,74Kr with temperature in covariant density functional theory

    Institute of Scientific and Technical Information of China (English)

    Wei Zhang; Yi-Fei Niu

    2017-01-01

    The rich phenomena of deformations in neutron-deficient krypton isotopes,such as shape evolution with neutron number and shape coexistence,have attracted the interest of nuclear physicists for decades.It is interesting to study such shape phenomena using a novel way,e.g.by thermally exciting the nucleus.In this work,we develop the finite temperature covariant density functional theory for axially deformed nuclei with the treatment of pairing correlations by the BCS approach,and apply this approach for the study of shape evolution in 72,74Kr with increasing temperature.For 72Kr,with temperature increasing,the nucleus firstly experiences a relatively quick weakening in oblate deformation at temperature T~0.9 MeV,and then changes from oblate to spherical at T~2.1 MeV.For 74Kr,its global minimum is at quadrupole deformationβ2 ~-0.14 and abruptly changes to spherical at T~ 1.7 MeV.The proton pairing transition occurs at critical temperature 0.6 MeV following the rule Tc=0.6Ap(0),where △p(0) is the proton pairing gap at zero temperature.The signatures of the above pairing transition and shape changes can be found in the specific heat curve.The single-particle level evolutions with temperature are presented.

  4. Laser-spectroscopy measurements of 72-96Kr spins, moments and charge radii

    International Nuclear Information System (INIS)

    Keim, M.

    1995-01-01

    The spins, moments and radii of krypton isotopes have been investigated by collinear fast-beam laser spectroscopy in combination with ultra-sensitive collisional ionization detection. The sequence of isotopes under study ranges from the neutron-deficient N=Z=36 isotope 72 Kr to the neutron-rich 96 Kr (N=60). The mean-square charge radii in the neighbourhood of the N=50 neutron-shell closure exhibit a pronounced shell effect which has recently been explained in the framework of relativistic mean-field theory. The results for the neutron-deficient nuclei are related to the shape coexistence of strongly prolate and near-spherical states which is known from nuclear spectroscopy. Here, an inversion of the odd-even staggering is observed below the neutron number N=45. The neutron-rich transitional nuclei are influenced by the N=56 subshell closure. In contrast to the N=60 isotones 97 Rb, 98 Sr and 100 Zr, the new isotope 96 Kr is not strongly deformed. ((orig.))

  5. Measurement of the electron quenching rate in an electron beam pumped KrF* laser

    International Nuclear Information System (INIS)

    Nishioka, Hajime; Kurashima, Toshio; Kuranishi, Hideaki; Ueda, Kenichi; Takuma, Hiroshi; Sasaki, Akira; Kasuya, Koichi.

    1988-01-01

    The electron quenching rate of KrF * in an electron beam pumped laser has been studied by accurately measuring the saturation intensity in a mixture of Ar/Kr/F 2 = 94/6/0.284. The input intensity of the measurements was widely varied from 100 W cm -2 (small signal region) to 100 MW cm -2 (absorption dominant region) in order to separate laser parameters which are small signal gain coefficient, absorption coefficient, and saturation intensity from the measured net gain coefficients. The gas pressure and the pump rate were varied in the range of 0.5 to 2.5 atm and 0.3 to 1.4 MW cm -3 , respectively. The electron quenching rate constant of 4.5 x 10 -7 cm 3 s -1 was obtained from the pressure and the pump rate dependence of the KrF * saturation intensity with the temperature dependence of the rate gas 3-body quenching rate as a function of gas temperature to the -3rd power. The small signal gain coefficients calculated with the determined quenching rate constants shows excellent agreement with the measurements. (author)

  6. Measurement of the electron quenching rate in an electron beam pumped KrF/sup */ laser

    Energy Technology Data Exchange (ETDEWEB)

    Nishioka, Hajime; Kurashima, Toshio; Kuranishi, Hideaki; Ueda, Kenichi; Takuma, Hiroshi; Sasaki, Akira; Kasuya, Koichi.

    1988-09-01

    The electron quenching rate of KrF/sup */ in an electron beam pumped laser has been studied by accurately measuring the saturation intensity in a mixture of Ar/Kr/F/sub 2/ = 94/6/0.284. The input intensity of the measurements was widely varied from 100 W cm/sup -2/ (small signal region) to 100 MW cm/sup -2/ (absorption dominant region) in order to separate laser parameters which are small signal gain coefficient, absorption coefficient, and saturation intensity from the measured net gain coefficients. The gas pressure and the pump rate were varied in the range of 0.5 to 2.5 atm and 0.3 to 1.4 MW cm/sup -3/, respectively. The electron quenching rate constant of 4.5 x 10/sup -7/ cm/sup 3/s/sup -1/ was obtained from the pressure and the pump rate dependence of the KrF/sup */ saturation intensity with the temperature dependence of the rate gas 3-body quenching rate as a function of gas temperature to the -3rd power. The small signal gain coefficients calculated with the determined quenching rate constants shows excellent agreement with the measurements.

  7. Theoretical study of the near uv photoabsorption by the Kr2* excimer

    International Nuclear Information System (INIS)

    Harvey, J.F.

    1990-04-01

    The physical process responsible for near UV photoabsorption by the Kr* 2 excimer are examined and the energy dependence of the photoabsorption cross sections is calculated. Near UV photoabsorption by the Kr* 2 is a multiprocess phenomenon involving direct photoionization and concurrent photoexcitation to a repulsive resonance state, which subsequently autoionizes or dissociates. An adiabatic nuclei theory is developed, based on the use of Feshbach projection operators, to separate the ionization and dissociation channels, and to device photoionization and photodissociation cross sections. These cross sections are expressed in terms of parameters obtained from fixed nuclei electronic calculations and in terms wavefunctions describing nuclear motion. Stieltjes Tchebycheff Moment Theory (STMT) techniques are used to extract information concerning the ionization continuum from localized L 2 electronic wavefunctions obtained from molecular electronic structure codes. Problems in the application of STMT techniques to narrow spectral features are examined. The cause of these problems is determined to be the use of the histogram midpoint approximation in low order STMT quadratures. Techniques are then developed which significantly improve the accuracy of STMT calculations for an isolated, narrow, resonance in a single continuum. Improved treatment of resonance profiles is demonstrated for pure Fano profiles, a shape resonance in a model barrier-and-well potential, and a shape resonance in the K-shell photoionization spectrum of N 2 . The improved STMT techniques are then used to obtain the fixed nuclei resonance profiles in the spectrum of Kr 2

  8. Long-term storage of 85Kr in amorphous zeolite 5A

    International Nuclear Information System (INIS)

    Penzhorn, R.D.; Noppel, H.E.; Dorea, A.; Guenther, K.; Leitzig, H.; Schuster, P.

    1984-01-01

    Ar, Kr and Xe can be immobilized in type A zeolites as well as in mordenite and chabazite, when the original crystal structure is hydrothermally vitrified in the presence of the densified gas. Zeolites containing a high percentage of earth alcali metals yield encapsulates that are thermally very stable. Gas fixation conditions are essentially independent of the form of aggregation of the matrix. Noble gas encapsulates were characterized by their specific surface area as well as by microprobe analysis, X-ray analysis and electron diffraction. The results indicate that Kr is immobilized in units smaller than the size of a zeolite crystal. The thermal conductivity of zeolites was determined experimentally in various fluid media. With the data obtained the heat transport through a final storage vessel cooled by natural air convection was calculated. The estimated temperature profiles correlate well with those obtained in experiments simulating a storage containment. To verify the process, active samples having specific activities up to 30 mCi/g have been prepared. Leaching results demonstrate the chemical stability of the Kr/5A encapsulates. A semi-pilot facility based on the one-way autoclave concept has been constructed and demonstrated in operation

  9. Phase Behavior Modeling of Asphaltene Precipitation for Heavy Crudes: A Promising Tool Along with Experimental Data

    Science.gov (United States)

    Tavakkoli, M.; Kharrat, R.; Masihi, M.; Ghazanfari, M. H.; Fadaei, S.

    2012-12-01

    Thermodynamic modeling is known as a promising tool for phase behavior modeling of asphaltene precipitation under different conditions such as pressure depletion and CO2 injection. In this work, a thermodynamic approach is used for modeling the phase behavior of asphaltene precipitation. The precipitated asphaltene phase is represented by an improved solid model, while the oil and gas phases are modeled with an equation of state. The PR-EOS was used to perform flash calculations. Then, the onset point and the amount of precipitated asphaltene were predicted. A computer code based on an improved solid model has been developed and used for predicting asphaltene precipitation data for one of Iranian heavy crudes, under pressure depletion and CO2 injection conditions. A significant improvement has been observed in predicting the asphaltene precipitation data under gas injection conditions. Especially for the maximum value of asphaltene precipitation and for the trend of the curve after the peak point, good agreement was observed. For gas injection conditions, comparison of the thermodynamic micellization model and the improved solid model showed that the thermodynamic micellization model cannot predict the maximum of precipitation as well as the improved solid model. The non-isothermal improved solid model has been used for predicting asphaltene precipitation data under pressure depletion conditions. The pressure depletion tests were done at different levels of temperature and pressure, and the parameters of a non-isothermal model were tuned using three onset pressures at three different temperatures for the considered crude. The results showed that the model is highly sensitive to the amount of solid molar volume along with the interaction coefficient parameter between the asphaltene component and light hydrocarbon components. Using a non-isothermal improved solid model, the asphaltene phase envelope was developed. It has been revealed that at high temperatures, an

  10. Photoemission from excited states in rare gas solids by combining synchrotronradiation with a laser

    International Nuclear Information System (INIS)

    Bernstorff, S.

    1984-09-01

    A new spectroscopic method has been developed to study excited states in rare gas solids: Excitons and conductionband-states are populated by synchrotron radiation (photon energy hw SR =5 - 30 eV). Subsequently electrons from these bound or conduction band-states are excited above the vacuum level of the solid by a pulsed dye laser (hw L =1.9 - 3.7 eV). This experimental technique was applied to solid Xe, Kr, Ar and Ne. (orig./GSCH)

  11. Inducing mineral precipitation in groundwater by addition of phosphate

    Directory of Open Access Journals (Sweden)

    Hartmann Thomas

    2011-10-01

    Full Text Available Abstract Background Induced precipitation of phosphate minerals to scavenge trace elements from groundwater is a potential remediation approach for contaminated aquifers. The success of engineered precipitation schemes depends on the particular phases generated, their rates of formation, and their long term stability. The purpose of this study was to examine the precipitation of calcium phosphate minerals under conditions representative of a natural groundwater. Because microorganisms are present in groundwater, and because some proposed schemes for phosphate mineral precipitation rely on stimulation of native microbial populations, we also tested the effect of bacterial cells (initial densities of 105 and 107 mL-1 added to the precipitation medium. In addition, we tested the effect of a trace mixture of propionic, isovaleric, formic and butyric acids (total concentration 0.035 mM. Results The general progression of mineral precipitation was similar under all of the study conditions, with initial formation of amorphous calcium phosphate, and transformation to poorly crystalline hydroxylapatite (HAP within one week. The presence of the bacterial cells appeared to delay precipitation, although by the end of the experiments the overall extent of precipitation was similar for all treatments. The stoichiometry of the final precipitates as well as Rietveld structure refinement using x-ray diffraction data indicated that the presence of organic acids and bacterial cells resulted in an increasing a and decreasing c lattice parameter, with the higher concentration of cells resulting in the greatest distortion. Uptake of Sr into the solids was decreased in the treatments with cells and organic acids, compared to the control. Conclusions Our results suggest that the minerals formed initially during an engineered precipitation application for trace element sequestration may not be the ones that control long-term immobilization of the contaminants. In

  12. Core drilling of deep borehole OL-KR37 at Olkiluoto in Eurajoki 2005

    Energy Technology Data Exchange (ETDEWEB)

    Niinimaeki, R. [Suomen Malmi Oy, Espoo (Finland)

    2005-11-15

    Posiva Oy submitted an application to the Finnish Government in May 1999 for the Decision in Principle to choose Olkiluoto in the municipality of Eurajoki as the site of the final disposal facility for spent nuclear fuel. A positive decision was made at the end of 2000 by the Government. The Finnish Parliament ratified the decision in May 2001. The decision makes it possible for Posiva to focus the confirming bedrock investigations at Olkiluoto, where in the next few years an underground rock characterisation facility, ONKALO, will be constructed. As a part of the investigations Suomen Malmi Oy (Smoy) core drilled 350.00 m and 45.10 m deep boreholes with a diameter of 75.7 mm at Olkiluoto in June- August 2005. The identification numbers of the boreholes are OL-KR37 and OL-KR37B, respectively. A set of monitoring measurements and samplings from the drilling and returning water was carried out during the drilling. Both the volume and the electric conductivity of the drilling water and the returning water were recorded. The drill rig was computer controlled and during drilling the computer recorded information about drilling parameters. The objective of all these measurements was to obtain more information about bedrock and groundwater properties. Sodium fluorescein was used as a label agent in the drilling water. The total volumes of the used drilling and flushing water were 273 m{sup 3} and 21m{sup 3} and the measured volumes of the returning water were 221m{sup 3} and 16m{sup 3} in boreholes OL-KR37 and OL-KR37B, respectively. The deviation of the borehole was measured with the deviation measuring instruments EMS and Maxibor. Uniaxial compressive strength, Young's Modulus and Poisson' s ratio were measured from the core samples. The average uniaxial compressive strength is about 106 MPa, the average Young's modulus is 40 GPa and the average Poisson's ratio is 0.20. The main rock types are migmatitic mica gneiss, granite and tonalite. Filled

  13. Stability investigations of zinc and cobalt precipitates immobilized by in situ bioprecipitation (ISBP) process

    KAUST Repository

    Satyawali, Yamini; Schols, Edo; Van Roy, Sandra; Dejonghe, Winnie; Diels, Ludo; Vanbroekhoven, Karolien

    2010-01-01

    In situ bioprecipitation (ISBP), which involves immobilizing the metals as precipitates (mainly sulphides) in the solid phase, is an effective method of metal removal from contaminated groundwater. This study investigated the stability of metal precipitates formed after ISBP in two different solid-liquid matrices (artificial and natural). The artificial matrix consisted of sand, Zn (200mgL-1), artificial groundwater and a carbon source (electron donor). Here the stability of the Zn precipitates was evaluated by manipulation of redox and pH. The natural system matrices included aquifer material and groundwater samples collected from three different metal (Zn and Co) contaminated sites and different carbon sources were provided as electron donors. In the natural matrices, metal precipitates stability was assessed by changing aquifer redox conditions, sequential extraction, and BIOMET® assay. The results indicated that, in the artificial matrix, redox manipulation did not impact the Zn precipitates. However the sequential pH change proved detrimental, releasing 58% of the precipitated Zn back into liquid phase. In natural matrices, the applied carbon source largely affected the stability of metal precipitates. Elemental analysis performed on the precipitates formed in natural matrix showed that the main elements of the precipitates were sulphur with Zn and Co. © 2010 Elsevier B.V.

  14. Stability investigations of zinc and cobalt precipitates immobilized by in situ bioprecipitation (ISBP) process

    KAUST Repository

    Satyawali, Yamini

    2010-09-01

    In situ bioprecipitation (ISBP), which involves immobilizing the metals as precipitates (mainly sulphides) in the solid phase, is an effective method of metal removal from contaminated groundwater. This study investigated the stability of metal precipitates formed after ISBP in two different solid-liquid matrices (artificial and natural). The artificial matrix consisted of sand, Zn (200mgL-1), artificial groundwater and a carbon source (electron donor). Here the stability of the Zn precipitates was evaluated by manipulation of redox and pH. The natural system matrices included aquifer material and groundwater samples collected from three different metal (Zn and Co) contaminated sites and different carbon sources were provided as electron donors. In the natural matrices, metal precipitates stability was assessed by changing aquifer redox conditions, sequential extraction, and BIOMET® assay. The results indicated that, in the artificial matrix, redox manipulation did not impact the Zn precipitates. However the sequential pH change proved detrimental, releasing 58% of the precipitated Zn back into liquid phase. In natural matrices, the applied carbon source largely affected the stability of metal precipitates. Elemental analysis performed on the precipitates formed in natural matrix showed that the main elements of the precipitates were sulphur with Zn and Co. © 2010 Elsevier B.V.

  15. The Precipitation Behavior of Poorly Water-Soluble Drugs with an Emphasis on the Digestion of Lipid Based Formulations.

    Science.gov (United States)

    Khan, Jamal; Rades, Thomas; Boyd, Ben

    2016-03-01

    An increasing number of newly discovered drugs are poorly water-soluble and the use of natural and synthetic lipids to improve the oral bioavailability of these drugs by utilizing the digestion pathway in-vivo has proved an effective formulation strategy. The mechanisms responsible for lipid digestion and drug solubilisation during gastrointestinal transit have been explored in detail, but the implications of drug precipitation beyond the potential adverse effect on bioavailability have received attention only in recent years. Specifically, these implications are that different solid forms of drug on precipitation may affect the total amount of drug absorbed in-vivo through their different physico-chemical properties, and the possibility that the dynamic environment of the small intestine may afford re-dissolution of precipitated drug if present in a high-energy form. This review describes the events that lead to drug precipitation during the dispersion and digestion of lipid based formulations, common methods used to inhibit precipitation, as well as conventional and newly emerging characterization techniques for studying the solid state form of the precipitated drug. Moreover, selected case studies are discussed where drug precipitation has ensued from the digestion of lipid based formulations, as well as the apparent link between drug ionisability and altered solid forms on precipitation, culminating in a discussion about the importance of the solid form on precipitation with relevance to the total drug absorbed.

  16. On the Precipitation and Precipitation Change in Alaska

    Directory of Open Access Journals (Sweden)

    Gerd Wendler

    2017-12-01

    Full Text Available Alaska observes very large differences in precipitation throughout the state; southeast Alaska experiences consistently wet conditions, while northern Arctic Alaska observes very dry conditions. The maximum mean annual precipitation of 5727 mm is observed in the southeastern panhandle at Little Port Arthur, while the minimum of 92 mm occurs on the North Slope at Kuparuk. Besides explaining these large differences due to geographic and orographic location, we discuss the changes in precipitation with time. Analyzing the 18 first-order National Weather Service stations, we found that the total average precipitation in the state increased by 17% over the last 67 years. The observed changes in precipitation are furthermore discussed as a function of the observed temperature increase of 2.1 °C, the mean temperature change of the 18 stations over the same period. This observed warming of Alaska is about three times the magnitude of the mean global warming and allows the air to hold more water vapor. Furthermore, we discuss the effect of the Pacific Decadal Oscillation (PDO, which has a strong influence on both the temperature and precipitation in Alaska.

  17. Laboratory-scale evaluations of alternative plutonium precipitation methods

    International Nuclear Information System (INIS)

    Martella, L.L.; Saba, M.T.; Campbell, G.K.

    1984-01-01

    Plutonium(III), (IV), and (VI) carbonate; plutonium(III) fluoride; plutonium(III) and (IV) oxalate; and plutonium(IV) and (VI) hydroxide precipitation methods were evaluated for conversion of plutonium nitrate anion-exchange eluate to a solid, and compared with the current plutonium peroxide precipitation method used at Rocky Flats. Plutonium(III) and (IV) oxalate, plutonium(III) fluoride, and plutonium(IV) hydroxide precipitations were the most effective of the alternative conversion methods tested because of the larger particle-size formation, faster filtration rates, and the low plutonium loss to the filtrate. These were found to be as efficient as, and in some cases more efficient than, the peroxide method. 18 references, 14 figures, 3 tables

  18. Dynamic simulation of the in-tank precipitation process

    International Nuclear Information System (INIS)

    Hang, T.; Shanahan, K.L.; Gregory, M.V.; Walker, D.D.

    1993-01-01

    As part of the High-Level Waste Tank Farm at the Savannah River Site (SRS), the In-Tank Precipitation (ITP) facility was designed to decontaminate the radioactive waste supernate by removing cesium as precipitated cesium tetraphenylborate. A dynamic computer model of the ITP process was developed using SPEEDUP TM software to provide guidance in the areas of operation and production forecast, production scheduling, safety, air emission, and process improvements. The model performs material balance calculations in all phase (solid, liquid, and gas) for 50 key chemical constituents to account for inventory accumulation, depletion, and dilution. Calculations include precipitation, benzene radiolytic reactions, evaporation, dissolution, adsorption, filtration, and stripping. To control the ITP batch operation a customized FORTRAN program was generated and linked to SPEEDUP TM simulation This paper summarizes the model development and initial results of the simulation study

  19. Energy-Transfer Kinetics for Xe (6p[1/2]0) Atoms in Kr, Ar, Ne, and He.

    Science.gov (United States)

    He, Shan; Liu, Dong; Li, Xueyang; Chu, Junzhi; Guo, Jingwei; Liu, Jinbo; Hu, Shu; Sang, Fengting; Jin, Yuqi

    2018-06-11

    The kinetic processes for the Xe (6p[1/2] 0 ) atoms in Kr, Ar, Ne, and He buffer gases were studied. We found that Kr, Ar, and Ne atoms can be used to switch the amplified spontaneous emission (ASE) channel from 3408 nm (6p[1/2] 0 -6s'[1/2] 1 ) to 3680 nm (5d[1/2] 1 -6p[1/2] 1 ), while Xe and He atoms do not show such a phenomenon. This ASE channel switch is mainly ascribed to the fast transfer of 6p[1/2] 0 → 5d[1/2] 1 . On the basis of the rate equations for two-state coupling (energy-transfer processes between the two states are very rapid), the reason why the ASE channel switch effect normally coincides with a double exponential decay of the spontaneous emission at 828 nm (6p[1/2] 0 -6s[3/2] 1 ) is explained. The actual situations in Xe, Ar, Ne, and He follow this rule. However, the strictly single exponential decay of the spontaneous emission at 828 nm and strong ASE channel switch effect simultaneously emerge in Kr. This indicates that the transfer of 6p[1/2] 0 → 5d[1/2] 1 in Kr does not occur via two-state coupling, but via two steps of near-resonance collision through the 5s[3/2] 2 (Kr) state as the intermediate state (6p[1/2] 0 → 5s[3/2] 2 (Kr) → 5d[1/2] 1 ). In addition, we found Xe (6p[1/2] 0 ) atoms strongly tend to reach the 6p[3/2] 2 , 6p[3/2] 1 , and 6p[5/2] 2 states through the 5s[3/2] 2 (Kr) state as the intermediate state in Kr. The 5s[3/2] 2 (Kr) state plays a very important role in the energy-transfer kinetics for the Xe (6p[1/2] 0 ) atoms. Kr is probably an excellent buffer gas for laser systems based on Xe.

  20. Modeling of asphaltene and wax precipitation

    Energy Technology Data Exchange (ETDEWEB)

    Chung, F.; Sarathi, P.; Jones, R.

    1991-01-01

    This research project was designed to focus on the development of a predictive technique for organic deposition during gas injection for petroleum EOR. A thermodynamic model has been developed to describe the effects of temperature, pressure, and composition on asphaltene precipitation. The proposed model combines regular solution theory with Flory-Huggins polymer solutions theory to predict maximum volume fractions of asphaltene dissolved in oil. The model requires evaluation of vapor-liquid equilibria, first using an equation of state followed by calculations of asphaltene solubility in the liquid-phase. A state-of-the-art technique for C{sub 7+} fraction characterization was employed in developing this model. The preliminary model developed in this work was able to predict qualitatively the trends of the effects of temperature, pressure, and composition. Since the mechanism of paraffinic wax deposition is different from that of asphaltene deposition, another thermodynamic model based on the solid-liquid solution theory was developed to predict the wax formation. This model is simple and can predict the wax appearance temperature with reasonable accuracy. Accompanying the modeling work, experimental studies were conducted to investigate the solubility of asphaltene in oil land solvents and to examine the effects of oil composition, CO{sub 2}, and solvent on asphaltene precipitation and its properties. This research focused on the solubility reversibility of asphaltene in oil and the precipitation caused by CO{sub 2} injection at simulated reservoir temperature and pressure conditions. These experiments have provided many observations about the properties of asphaltenes for further improvement of the model, but more detailed information about the properties of asphaltenes in solution is needed for the development of more reliable asphaltene characterization techniques. 50 refs., 8 figs., 7 tabs.