WorldWideScience

Sample records for solid content ssc

  1. Effects of the Solid Solution Heat Treatment on the Corrosion Resistance Property of SSC13 Cast Alloy

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kuk-Jin [Hi-Sten Co., Ltd., Gimhae (Korea, Republic of); Lim, Su Gun [Gyeongsang National University, Jinju (Korea, Republic of); Pak, S. J. [Gachon BioNano Research Institute, Gachon University, Sungnam (Korea, Republic of)

    2015-04-15

    Recently, Stainless steels have been increasingly selected as the fitting or the valve materials of water pipes as the human health issue is getting higher and higher. Therefore, the connectors attached at pipes to deliver water are exposed to more severe environments than the pipes because crevice or galvanic corrosion is apt to occur at the fittings or the valves. Effects of the solid solution annealing, cooling rate after this heat treatment, and passivation on the corrosion properties of the shell mold casted SSC13 (STS304 alloy equivalent) were studied. The heating and quenching treatment more or less reduced hardness but effectively improved corrosion resistance. It was explained by the reduction of delta ferrite contents. Independent of heat treatment, the chemical passivation treatment also lowered corrosion rate but the improvement of corrosion resistance depended on temperature and time for passivation treatment indicating that the optimum conditions for passivation treatment were the bath temperature of 34 .deg. C and operating time of 10 minutes. Therefore it is suggested that the corrosion resistance of SSC13 can be effectively improved with the heat treatment, where SSC13 is heated for 10 minutes at 1120 °C and quenched and passivation treatment, where SSC13 is passivated for at least 10 seconds at 34 °C nitric acid solution.

  2. Robust model of fresh jujube soluble solids content with near ...

    African Journals Online (AJOL)

    A robust partial least square (PLS) calibration model with high accuracy and stability was established for the measurement of soluble solids content (SSC) of fresh jujube using near-infrared (NIR) spectroscopy technique. Fresh jujube samples were collected in different areas of Taigu and Taiyuan cities, central China in ...

  3. Measurement of soluble solids content in watermelon by Vis/NIR diffuse transmittance technique*

    OpenAIRE

    Tian, Hai-qing; Ying, Yi-bin; Lu, Hui-shan; Fu, Xia-ping; Yu, Hai-yan

    2007-01-01

    Watermelon is a popular fruit in the world with soluble solids content (SSC) being one of the major characteristics used for assessing its quality. This study was aimed at obtaining a method for nondestructive SSC detection of watermelons by means of visible/near infrared (Vis/NIR) diffuse transmittance technique. Vis/NIR transmittance spectra of intact watermelons were acquired using a low-cost commercially available spectrometer operating over the range 350~1000 nm. Spectra data were analyz...

  4. Predicting pear (cv. Clara Frijs) dry matter and soluble solids content with near infrared spectroscopy

    DEFF Research Database (Denmark)

    Travers, Sylvia; Bertelsen, Marianne; Petersen, Karen

    2014-01-01

    Regression models for predicting preharvest dry matter (DM) and soluble solids content (SSC), based on two spectral ranges (680-1000 nm and 1100-2350 nm), were compared. Models based on longer NIR spectra were more successful for both parameters (DM/SSC: R2 = 0.78-0.84; RMECV = 0.78/0.44; LVs = 6....../7). SSC prediction was better than expected considering the presence of starch in fruit. Generally poor SSC prediction in the presence of starch could be related to the inability of models to distinguish between forms of carbohydrate. Variable selection and regression coefficients highlighted...... fruit. Further research is needed to qualify and build on the results presented here....

  5. Potable NIR spectroscopy predicting soluble solids content of pears based on LEDs

    Energy Technology Data Exchange (ETDEWEB)

    Liu Yande; Liu Wei; Sun Xudong; Gao Rongjie; Pan Yuanyuan; Ouyang Aiguo, E-mail: jxliuyd@163.com [School of Mechatronics Engineering, East China Jiaotong University, Changbei Open and Developing District, Nanchang, 330013 (China)

    2011-01-01

    A portable near-infrared (NIR) instrument was developed for predicting soluble solids content (SSC) of pears equipped with light emitting diodes (LEDs). NIR spectra were collected on the calibration and prediction sets (145:45). Relationships between spectra and SSC were developed by multivariate linear regression (MLR), partial least squares (PLS) and artificial neural networks (ANNs) in the calibration set. The 45 unknown pears were applied to evaluate the performance of them in terms of root mean square errors of prediction (RMSEP) and correlation coefficients (r). The best result was obtained by PLS with RMSEP of 0.62{sup 0}Brix and r of 0.82. The results showed that the SSC of pears could be predicted by the portable NIR instrument.

  6. Potable NIR spectroscopy predicting soluble solids content of pears based on LEDs

    International Nuclear Information System (INIS)

    Liu Yande; Liu Wei; Sun Xudong; Gao Rongjie; Pan Yuanyuan; Ouyang Aiguo

    2011-01-01

    A portable near-infrared (NIR) instrument was developed for predicting soluble solids content (SSC) of pears equipped with light emitting diodes (LEDs). NIR spectra were collected on the calibration and prediction sets (145:45). Relationships between spectra and SSC were developed by multivariate linear regression (MLR), partial least squares (PLS) and artificial neural networks (ANNs) in the calibration set. The 45 unknown pears were applied to evaluate the performance of them in terms of root mean square errors of prediction (RMSEP) and correlation coefficients (r). The best result was obtained by PLS with RMSEP of 0.62 0 Brix and r of 0.82. The results showed that the SSC of pears could be predicted by the portable NIR instrument.

  7. A bi-layer model for nondestructive prediction of soluble solids content in apple based on reflectance spectra and peel pigments.

    Science.gov (United States)

    Tian, Xi; Li, Jiangbo; Wang, Qingyan; Fan, Shuxiang; Huang, Wenqian

    2018-01-15

    Hyperspectral imaging technology was used to investigate the effect of various peel colors on soluble solids content (SSC) prediction model and build a SSC model insensitive to the color distribution of apple peel. The SSC and peel pigments were measured, effective wavelengths (EWs) of SSC and pigments were selected from the acquired hyperspectral images of the intact and peeled apple samples, respectively. The effect of pigments on the SSC prediction was studied and optimal SSC EWs were selected from the peel-flesh layers spectra after removing the chlorophyll and anthocyanin EWs. Then, the optimal bi-layer model for SSC prediction was built based on the finally selected optimal SSC EWs. Results showed that the correlation coefficient of prediction, root mean square error of prediction and selected bands of the bi-layer model were 0.9560, 0.2528 and 41, respectively, which will be more acceptable for future online SSC prediction of various colors of apple. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Prediction of soluble solids content and ph in red wine by visible and near infrared spectroscopy

    Science.gov (United States)

    Wang, Li; He, Yong; Wang, Yanyan

    2008-02-01

    Soluble solids content (SSC) and pH are two major characteristic used for assessing quality of red wine, and they are also two important quality indexes in the manufacture of red wine. For rapid detection of SSC and pH in red wine, visible and near infrared (Vis/NIR) transmittance spectroscopy technique combined with partial least squares (PLS) and least squares support vector machines (LS-SVM) were used in this study. First, the near infrared transmittance spectra of 175 red wine samples were obtained using Vis/NIR spectroradiometer, then, PLS was applied for reducing the dimensionality of the original spectra, latent variables (LVs) selected by PLS could be used to replace the complex spectral data. All samples were randomly separated into calibration set and validation set. The LVs (selected by PLS) of each sample in calibration set was used as the inputs to train the LS-SVM model, then the optimal model was used to predict the SSC and pH values of samples in validation set based on their LVs. Standard error prediction (SEP) and determination coefficient (r2) were used as the evaluation standards, and the results indicated that the SEP and r2 for the prediction of SSC were 0.2313 and 0.9348; while 0.0071 and 0.9986 for pH. This prediction model was more accurate compared with the related research.

  9. Measurement of soluble solids content in watermelon by Vis/NIR diffuse transmittance technique.

    Science.gov (United States)

    Tian, Hai-qing; Ying, Yi-bin; Lu, Hui-shan; Fu, Xia-ping; Yu, Hai-yan

    2007-02-01

    Watermelon is a popular fruit in the world with soluble solids content (SSC) being one of the major characteristics used for assessing its quality. This study was aimed at obtaining a method for nondestructive SSC detection of watermelons by means of visible/near infrared (Vis/NIR) diffuse transmittance technique. Vis/NIR transmittance spectra of intact watermelons were acquired using a low-cost commercially available spectrometer operating over the range 350~1000 nm. Spectra data were analyzed by two multivariate calibration techniques: partial least squares (PLS) and principal component regression (PCR) methods. Two experiments were designed for two varieties of watermelons [Qilin (QL), Zaochunhongyu (ZC)], which have different skin thickness range and shape dimensions. The influences of different data preprocessing and spectra treatments were also investigated. Performance of different models was assessed in terms of root mean square errors of calibration (RMSEC), root mean square errors of prediction (RMSEP) and correlation coefficient (r) between the predicted and measured parameter values. Results showed that spectra data preprocessing influenced the performance of the calibration models. The first derivative spectra showed the best results with high correlation coefficient of determination [r=0.918 (QL); r=0.954 (ZC)], low RMSEP [0.65 degrees Brix (QL); 0.58 degrees Brix (ZC)], low RMSEC [0.48 degrees Brix (QL); 0.34 degrees Brix (ZC)] and small difference between the RMSEP and the RMSEC by PLS method. The nondestructive Vis/NIR measurements provided good estimates of SSC index of watermelon, and the predicted values were highly correlated with destructively measured values for SSC. The models based on smoothing spectra (Savitzky-Golay filter smoothing method) did not enhance the performance of calibration models obviously. The results indicated the feasibility of Vis/NIR diffuse transmittance spectral analysis for predicting watermelon SSC in a

  10. [Application of characteristic NIR variables selection in portable detection of soluble solids content of apple by near infrared spectroscopy].

    Science.gov (United States)

    Fan, Shu-Xiang; Huang, Wen-Qian; Li, Jiang-Bo; Guo, Zhi-Ming; Zhaq, Chun-Jiang

    2014-10-01

    In order to detect the soluble solids content(SSC)of apple conveniently and rapidly, a ring fiber probe and a portable spectrometer were applied to obtain the spectroscopy of apple. Different wavelength variable selection methods, including unin- formative variable elimination (UVE), competitive adaptive reweighted sampling (CARS) and genetic algorithm (GA) were pro- posed to select effective wavelength variables of the NIR spectroscopy of the SSC in apple based on PLS. The back interval LS- SVM (BiLS-SVM) and GA were used to select effective wavelength variables based on LS-SVM. Selected wavelength variables and full wavelength range were set as input variables of PLS model and LS-SVM model, respectively. The results indicated that PLS model built using GA-CARS on 50 characteristic variables selected from full-spectrum which had 1512 wavelengths achieved the optimal performance. The correlation coefficient (Rp) and root mean square error of prediction (RMSEP) for prediction sets were 0.962, 0.403°Brix respectively for SSC. The proposed method of GA-CARS could effectively simplify the portable detection model of SSC in apple based on near infrared spectroscopy and enhance the predictive precision. The study can provide a reference for the development of portable apple soluble solids content spectrometer.

  11. Near Infrared Spectral Linearisation in Quantifying Soluble Solids Content of Intact Carambola

    Directory of Open Access Journals (Sweden)

    Mohd Zubir MatJafri

    2013-04-01

    Full Text Available This study presents a novel application of near infrared (NIR spectral linearisation for measuring the soluble solids content (SSC of carambola fruits. NIR spectra were measured using reflectance and interactance methods. In this study, only the interactance measurement technique successfully generated a reliable measurement result with a coefficient of determination of (R2 = 0.724 and a root mean square error of prediction for (RMSEP = 0.461° Brix. The results from this technique produced a highly accurate and stable prediction model compared with multiple linear regression techniques.

  12. Near infrared spectral linearisation in quantifying soluble solids content of intact carambola.

    Science.gov (United States)

    Omar, Ahmad Fairuz; MatJafri, Mohd Zubir

    2013-04-12

    This study presents a novel application of near infrared (NIR) spectral linearisation for measuring the soluble solids content (SSC) of carambola fruits. NIR spectra were measured using reflectance and interactance methods. In this study, only the interactance measurement technique successfully generated a reliable measurement result with a coefficient of determination of (R2) = 0.724 and a root mean square error of prediction for (RMSEP) = 0.461° Brix. The results from this technique produced a highly accurate and stable prediction model compared with multiple linear regression techniques.

  13. Determination of solid fat content by NMR

    International Nuclear Information System (INIS)

    Kawada, Tsukasa; Kato, Chihiro; Suzuki, Kazuaki

    1984-01-01

    To establish a standard method for determing solid fat content, the NMR method was tested at six laboratories and the results were examined for collaboration. Two types of instruments, pulse NMR and wide-line NMR were used. Standard deviation in results at six laboratories was less than 1.5 for the step wise method, but more than 1.5 for the rapid method. The standard deviation in results at a single laboratory was much less than either of these cases. No significant difference could be observed in the values obtained using both instruments. Solid fat content values measured for a mixture of fully hydrogenated rapeseed and rapeseed oil agreed well with the percentage of solid by weight. (author)

  14. Nondestructive quantification of the soluble-solids content and the available acidity of apples by Fourier-transform near-infrared spectroscopy

    Science.gov (United States)

    Ying, Yibin; Liu, Yande; Tao, Yang

    2005-09-01

    This research evaluated the feasibility of using Fourier-transform near-infrared (FT-NIR) spectroscopy to quantify the soluble-solids content (SSC) and the available acidity (VA) in intact apples. Partial least-squares calibration models, obtained from several preprocessing techniques (smoothing, derivative, etc.) in several wave-number ranges were compared. The best models were obtained with the high coefficient determination (r) 0.940 for the SSC and a moderate r of 0.801 for the VA, root-mean-square errors of prediction of 0.272% and 0.053%, and root-mean-square errors of calibration of 0.261% and 0.046%, respectively. The results indicate that the FT-NIR spectroscopy yields good predictions of the SSC and also showed the feasibility of using it to predict the VA of apples.

  15. Nondestructive quantification of the soluble-solids content and the available acidity of apples by Fourier-transform near-infrared spectroscopy

    International Nuclear Information System (INIS)

    Ying Yibin; Liu Yande; Tao Yang

    2005-01-01

    This research evaluated the feasibility of using Fourier-transform near-infrared (FT-NIR) spectroscopy to quantify the soluble-solids content (SSC) and the available acidity (VA) in intact apples. Partial least-squares calibration models, obtained from several preprocessing techniques (smoothing, derivative, etc.) in several wave-number ranges were compared. The best models were obtained with the high coefficient determination (r 2 ) 0.940 for the SSC and a moderate r 2 of 0.801 for the VA, root-mean-square errors of prediction of 0.272% and 0.053%, and root-mean-square errors of calibration of 0.261% and 0.046%, respectively. The results indicate that the FT-NIR spectroscopy yields good predictions of the SSC and also showed the feasibility of using it to predict the VA of apples

  16. Evaluation of soluble solids content and pH of ice cream treated with gamma radiation

    Energy Technology Data Exchange (ETDEWEB)

    Rogovschi, V.D.; Nunes, T.C.F.; Fabbri, A.D.T.; Sagretti, J.M.; Sabato, S.F. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    The ice cream is considered an aerated suspension of fat and ice crystals in a concentrated sugar solution containing hydrocolloids, proteins and casein micelles. Only in Brazil, in the year 2010, it was produced 1120 million liter of ice cream and due to high demand by the consumers, this is considered the most important product of the dairy industry. The objective of this work is to evaluate the soluble solids content (SSC) and the hydrogenionic potential (pH) of vanilla ice cream conditioned in isothermal boxes irradiated with 3.0 and 5.0 kGy in the Multipurpose Irradiator of {sup 60}Co located at IPEN - CNEN/SP. It can be concluded that the treatment of ice cream with gamma radiation did not cause changes in the analyzed parameters. . (author)

  17. Evaluation of soluble solids content and pH of ice cream treated with gamma radiation

    International Nuclear Information System (INIS)

    Rogovschi, V.D.; Nunes, T.C.F.; Fabbri, A.D.T.; Sagretti, J.M.; Sabato, S.F.

    2011-01-01

    The ice cream is considered an aerated suspension of fat and ice crystals in a concentrated sugar solution containing hydrocolloids, proteins and casein micelles. Only in Brazil, in the year 2010, it was produced 1120 million liter of ice cream and due to high demand by the consumers, this is considered the most important product of the dairy industry. The objective of this work is to evaluate the soluble solids content (SSC) and the hydrogenionic potential (pH) of vanilla ice cream conditioned in isothermal boxes irradiated with 3.0 and 5.0 kGy in the Multipurpose Irradiator of 60 Co located at IPEN - CNEN/SP. It can be concluded that the treatment of ice cream with gamma radiation did not cause changes in the analyzed parameters. . (author)

  18. SUPERCOLLIDER: SDC for SSC

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1992-03-15

    On a scale to match the 87-kilometre Superconducting Supercollider (SSC) planned for Ellis County, Texas, the Solenoidal Detector Collaboration (SDC) is designing a large general purpose detector to pursue a broad range of physics goals.

  19. SSC seeks aid

    CERN Multimedia

    1990-01-01

    The chairman of the science committee in the US House of representatives will ask Congress to pass a law requiring that at least a quarter of the funds for the SSC come from foreign money (2 paragraphs).

  20. SUPERCOLLIDER: SDC for SSC

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    On a scale to match the 87-kilometre Superconducting Supercollider (SSC) planned for Ellis County, Texas, the Solenoidal Detector Collaboration (SDC) is designing a large general purpose detector to pursue a broad range of physics goals

  1. Prospects for SSC physics

    International Nuclear Information System (INIS)

    Paige, F.E.

    1986-03-01

    The SSC is primarily designed to explore the physics of the 1 TeV mass scale. Since new heavy particles will decay either into other new particles or into the quanta of the standard model, the main goal of SSC experiments will be to identify and to measure these quanta well. Progress in simulating events and in understanding the signature and backgrounds for standard-model physics is described. 51 refs

  2. SSC accelerator availability allocation

    International Nuclear Information System (INIS)

    Dixon, K.T.; Franciscovich, J.

    1991-03-01

    Superconducting Super Collider (SSC) operational availability is an area of major concern, judged by the Central Design Group to present such risk that use of modern engineering tools would be essential to program success. Experience has shown that as accelerator beam availability falls below about 80%, efficiency of physics experiments degrades rapidly due to inability to maintain adequate coincident accelerator and detector operation. For this reason, the SSC availability goal has been set at 80%, even though the Fermi National Accelerator Laboratory accelerator, with a fraction of the SSC's complexity, has only recently approached that level. This paper describes the allocation of the top-level goal to part-level reliability and maintainability requirements, and it gives the results of parameter sensitivity studies designed to help identify the best approach to achieve the needed system availability within funding and schedule constraints. 1 ref., 12 figs., 4 tabs

  3. SSC accelerator physics

    International Nuclear Information System (INIS)

    Anon.

    1985-01-01

    Accelerator physicists at LBL began intensive work on the SSC in 1983, in support of the proposed 6.5-T magnet design, which, in turn, became reference design A during the Reference Designs Study. In that same study, LBL physicists formed the core of the accelerator physics group led by Fermilab's Don Edwards. In a period of only a few months, that group established preliminary parameters for a near-optimal design, produced conceptual designs based on three magnet types, addressed all significant beam lifetime and stability issues, and identified areas requiring further R and D. Since the conclusion of the Reference Designs Study, work has focused on the key SSC design issue, namely, single-particle stability in an imperfect magnetic field. At the end of fiscal 1984, much of the LBL accelerator physics group took its place in the SSC Central Design Group, whose headquarters at LBL will be the focus of nationwide SSC R and D efforts over the next several years

  4. SSC design update

    International Nuclear Information System (INIS)

    Syphers, M.J.

    1992-11-01

    Recent developments in the design and construction of the SSC are presented. Topics include status of the 20 TeV Collider rings, including interaction regions, utility regions, and main arcs, plus some remarks on the injector accelerators. Remaining issues facing the design of the colliding beams synchrotron and its injectors are discussed

  5. Calorimetry at the SSC

    International Nuclear Information System (INIS)

    Wigmans, R.

    1988-01-01

    The state of the art, and the present understanding of the basic limitations in hadron calorimetry, are briefly described. The various options for SSC calorimeters are discussed, and the R ampersand D needed for the ones that look most promising is outlined. The most promising candidates are (1) lead/scintillating fibers and (2) lead (or uranium)/TMS (or other warm liquids)

  6. Calorimetry at the SSC

    International Nuclear Information System (INIS)

    Wigmans, R.

    1987-09-01

    The state of the art, and our present understanding of the basic limitations in hadron calorimetry, are briefly described. The various options for SSC calorimeters are discussed, and the R and D needed for the ones that look most promising is outlined. 13 refs.; 8 figs

  7. Solid-soluted content of cerium in solid solution of sphene

    International Nuclear Information System (INIS)

    Zhao Wei; Teng Yuancheng; Li Yuxiang; Ren Xuetan; Huang Junjun

    2010-01-01

    The sphene solid solution was synthesized by solid-state method,with calcium carbonate, silica, titanium dioxide, cerium oxalate and alumina as raw materials. The solid-soluted content of cerium in sphene was researched by means of X-ray diffraction (XRD), backscattering scanning electron microscopy (BSE), energy dispersive spectroscopy (EDS) and so on. The influence of A l3+ ion introduction to sphene on the solid-soluted content of cerium in sphene solid solution was studied. The results indicate that when introducing Al 3+ to sphene as electrovalence compensation, Ce 4+ could be well solidified to Ca 1-x Ce x Ti 1-2x A l2x SiO 5 , and the solid-soluted content is approximately 12.61%. With no electrovalence compensation, Ce 4+ could be solidified to Ca 1-2x Ce x TiSiO 5 , and the solid-soluted content is approximately 10.98%. The appropriate synthesis temperature of sphene solid solution is 1 260 degree C.(authors)

  8. Software methodologies for the SSC

    International Nuclear Information System (INIS)

    Loken, S.C.

    1990-01-01

    This report describes some of the considerations that will determine how the author developed software for the SSC. He begins with a review of the general computing problem for SSC experiments and recent experiences in software engineering for the present generation of experiments. This leads to a discussion of the software technologies that will be critical for the SSC experiments. He describes the emerging software standards and commercial products that may be useful in addressing the SSC needs. He concludes with some comments on how collaborations and the SSC Lab should approach the software development issue

  9. SSC Cryogenic System

    International Nuclear Information System (INIS)

    Brown, D.P.; Louttit, R.I.; Rode, C.; VanderArend, P.C.

    1985-01-01

    The design of the 4.5 K primary cooling system and higher temperature shield cooling systems for the SSC are described. Typical flow diagrams for the magnet piping systems are presented. Estimated heat loads are given. The systems have been designed to accomodate the great distances, 90 km and up, over which the load will be distributed. Provision has been made for cooldown, warmup, quench recovery and magnet replacement, as well as for steady-state operation

  10. SSC kicker impedances

    International Nuclear Information System (INIS)

    Colton, E.P.; Wang, T.F.

    1985-01-01

    The longitudinal and transverse complex impedances Z/sub l//n and Z/sub t/, respectively, have been calculated for both the SSC injection and abort kickers. The calculations assumed that no attempt was made to shield the beam from the kickers. We took the injection and abort kickers to be as specified. The injection kickers were ferrite with a single-turn design, and the abort kickers were of a ''window-frame design'' with tape wound cores

  11. Cultural connections of the SSC

    International Nuclear Information System (INIS)

    Kirk, T.B.W.

    1984-01-01

    This paper has as its purpose, to consider explicitly and in more than cursory detail, the cultural involvement of a major scientific facility, the SSC, with its public surroundings. At the moment of writing, it is uncertain whether the project will evolve under US-national or under international sponsorship. Since most of the paper's substantive content is invariant with respect to this question (but the means of implementation are not), the author proceeds as though the machine will be US sponsored. This assumption avoids the irritation of having to identify continually the particular methods for implementation of the ideas presented. If the international route is chosen, a second paper could be written to accommodate this outcome. By cultural involvement, the author is principally concerned with the following areas: i) accessibility of the facility to the general public; ii) educational potential at and away from the site; iii) architectural and aesthetic considerations; and iv) formal history of the project

  12. Effect of solid-meal caloric content on gastric emptying kinetics of solids and liquids.

    Science.gov (United States)

    Urbain, J L; Siegel, J A; Mortelmans, L; van Cutsem, E; van den Maegdenbergh, V; de Roo, M

    1989-08-01

    In this study, we have evaluated the effect of the caloric content of a physiological test meal on the gastric emptying kinetics of solids and liquids. 22 healthy male volunteers were studied in two groups matched for age. After an overnight fast, each volunteer underwent the same test procedure; in the first group (G I), 10 volunteers received a meal consisting of bread, 111In-DTPA water and 1 scrambled egg labeled with 99mTc-labelled sulphur colloid; in the second group (G II) 12 volunteers were given the same meal but with 2 labeled eggs in order to increase the caloric content of the solid phase meal. Simultaneous anterior and posterior images were recorded using a dual-headed gamma camera. Solid and liquid geometric mean data were analyzed to determine the lag phase, the emptying rate and the half-emptying time for both solids and liquids. Solid and liquid gastric half-emptying times were significantly prolonged in G II compared to G I volunteers. For the solid phased, the delay was accounted for by a longer lag phase and a decrease in the equilibrium emptying rate. The emptying rate of the liquid phase was significantly decreased in G II compared to G I. Within each group, no statistically significant difference was observed between solid and liquid emptying rates. We conclude that the caloric content of the solid portion of a meal not only alters the emptying of the solid phase but also affects the emptying of the liquid component of the meal.

  13. Effect of solid-meal caloric content on gastric emptying kinetics of solids and liquids

    International Nuclear Information System (INIS)

    Urbain, J.L.; Mortelmans, L.; Cutsem, E. van; Maegdenbergh, V. van den; Roo, M. de

    1989-01-01

    In this study, we have evaluated the effect of the caloric content of a physiological test meal on the gastric emptying kinetics of solids and liquids. 22 healthy male volunteers were studied in two groups matched for age. After an overnight fast, each volunteer underwent the same test procedure; in the first group (G I), 10 volunteers received a meal consisting of bread, 111 In-DTPA water and 1 scrambled egg labeled with 99m Tc-labelled sulphur colloid; in the second group (G II) 12 volunteers were given the same meal but with 2 labeled eggs in order to increase the caloric content of the solid phase meal. Simultaneous anterior and posterior images were recorded using a dual-headed gamma camera. Solid and liquid geometric mean data were analyzed to determine the lag phase, the emptying rate and the half-emptying time for both solids and liquids. Solid and liquid gastric half-emptying times were significantly prolonged in G II compared to G I volunteers. For the solid phased, the delay was accounted for by a longer lag phase and a decrease in the equilibrium emptying rate. The emptying rate of the liquid phase was significantly decreased in G II compared to G I. Within each group, no statistically significant difference was observed between solid and liquid emptying rates. We conclude that the caloric content of the solid portion of a meal not only alters the emptying of the solid phase but also affects the emptying of the liquid component of the meal. (orig.) [de

  14. Calorimetry for the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, H.A.; Grannis, P.D.

    1984-01-01

    The activities related to calorimetry at Snowmass took place in three main areas. These were: (1) The performance criteria for SSC calorimetry, including the requirements on hermeticity, shower containment, segmentation and time resolution. The use of calorimetric means of particle identification was studied. (2) The study of triggering methods using calorimeter energy, angle and timing information. (3) A review of a wide variety of calorimeter materials for absorber and sampling, as well as several means of obtaining the readout of the energy deposits. 48 references, 10 figures, 1 table.

  15. Calorimetry for the SSC

    International Nuclear Information System (INIS)

    Gordon, H.A.; Grannis, P.D.

    1984-01-01

    The activities related to calorimetry at Snowmass took place in three main areas. These were: (1) The performance criteria for SSC calorimetry, including the requirements on hermeticity, shower containment, segmentation and time resolution. The use of calorimetric means of particle identification was studied. (2) The study of triggering methods using calorimeter energy, angle and timing information. (3) A review of a wide variety of calorimeter materials for absorber and sampling, as well as several means of obtaining the readout of the energy deposits. 48 references, 10 figures, 1 table

  16. WLWL scattering at the SSC

    International Nuclear Information System (INIS)

    Bagger, J.; Valencia, G.

    1990-01-01

    We use higher-order chiral Lagrangians to study W L W L scattering at the SSC. We analyze a model that is consistent with crossing, unitarity and chiral symmetry, with no resonant behavior at SSC energies. The only signal is a slightly enhanced rate for W L W L scattering. Our results indicate the level of sensitivity that must be reached before the SSC can be assured of discovering the mechanism for electroweak symmetry breaking. 19 refs., 4 figs., 2 tabs

  17. Chiral Lagrangians and the SSC

    International Nuclear Information System (INIS)

    Dawson, S.

    1991-09-01

    In the event that the SSC does not observe any resonances such as a Higgs boson or a techni-rho meson, we would like to know if the SSC can still discover something about the nature of the electroweak symmetry breaking. We will use chiral Lagrangian techniques to address this question and analyze their utility for studying events containing W and Z gauge bosons at the SSC. 20 refs., 4 figs

  18. Radiation effects at the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Gilchriese, M.G.D. [ed.] [Superconducting Super Collider Lab., Dallas, TX (United States)

    1988-06-01

    This report contains a preliminary study of the effects of the radiation levels expected at the SSC on potential detector components and a subset of materials to be used in the SSC accelerators. The report does not contain a discussion of radiation damage to electronics components that may be used at the SSC. We have investigated many of the effects of radiation on silicon detectors, on wire chambers, on scintillating materials and the associated readout, on optical fibers for data transmission and on structural or other materials to be used in detector or accelerator components. In the SSC accelerator complex, in particular the storage rings, radiation damage will not present significant problems different than those now faced by existing high energy accelerators. We find that the effects of radiation damage on SSC detector components will be significant at the design luminosity of the ssc and will limit, or determine, many of the options for different detector components. In this regard the reader should keep in mind that, in the absence of a specific detector design, it is not possible to form definitive conclusions regarding the viability of the detector components. Since the radiation levels in experiments at the SSC will depend on the geometry and composition of the apparatus, simple yes /no generalizations about the feasibility of a detector component are not possible.

  19. SSC muon detector group report

    International Nuclear Information System (INIS)

    Carlsmith, D.; Groom, D.; Hedin, D.; Kirk, T.; Ohsugi, T.; Reeder, D.; Rosner, J.; Wojcicki, S.

    1986-01-01

    We report here on results from the Muon Detector Group which met to discuss aspects of muon detection for the reference 4π detector models put forward for evaluation at the Snowmass 1986 Summer Study. We report on: suitable overall detector geometry; muon energy loss mechanisms; muon orbit determination; muon momentum and angle measurement resolution; raw muon rates and trigger concepts; plus we identify SSC physics for which muon detection will play a significant role. We conclude that muon detection at SSC energies and luminosities is feasible and will play an important role in the evolution of physics at the SSC

  20. SSC muon detector group report

    Energy Technology Data Exchange (ETDEWEB)

    Carlsmith, D.; Groom, D.; Hedin, D.; Kirk, T.; Ohsugi, T.; Reeder, D.; Rosner, J.; Wojcicki, S.

    1986-01-01

    We report here on results from the Muon Detector Group which met to discuss aspects of muon detection for the reference 4..pi.. detector models put forward for evaluation at the Snowmass 1986 Summer Study. We report on: suitable overall detector geometry; muon energy loss mechanisms; muon orbit determination; muon momentum and angle measurement resolution; raw muon rates and trigger concepts; plus we identify SSC physics for which muon detection will play a significant role. We conclude that muon detection at SSC energies and luminosities is feasible and will play an important role in the evolution of physics at the SSC.

  1. Engineering properties for high kitchen waste content municipal solid waste

    Directory of Open Access Journals (Sweden)

    Wu Gao

    2015-12-01

    Full Text Available Engineering properties of municipal solid waste (MSW depend largely on the waste's initial composition and degree of degradation. MSWs in developing countries usually have a high kitchen waste content (called HKWC MSW. After comparing and analyzing the laboratory and field test results of physical composition, hydraulic properties, gas generation and gas permeability, and mechanical properties for HKWC MSW and low kitchen waste content MSW (called LKWC MSW, the following findings were obtained: (1 HKWC MSW has a higher initial water content (IWC than LKWC MSW, but the field capacities of decomposed HKWC and LKWC MSWs are similar; (2 the hydraulic conductivity and gas permeability for HKWC MSW are both an order of magnitude smaller than those for LKWC MSW; (3 compared with LKWC MSW, HKWC MSW has a higher landfill gas (LFG generation rate but a shorter duration and a lower potential capacity; (4 the primary compression feature for decomposed HKWC MSW is similar to that of decomposed LKWC MSW, but the compression induced by degradation of HKWC MSW is greater than that of LKWC MSW; and (5 the shear strength of HKWC MSW changes significantly with time and strain. Based on the differences of engineering properties between these two kinds of MSWs, the geo-environmental issues in HKWC MSW landfills were analyzed, including high leachate production, high leachate mounds, low LFG collection efficiency, large settlement and slope stability problem, and corresponding advice for the management and design of HKWC MSW landfills was recommended.

  2. JUICE EXTRACTION FOR TOTAL SOLUBLE SOLIDS CONTENT DETERMINATION IN MELON

    Directory of Open Access Journals (Sweden)

    Paulo Sérgio Lima e Silva

    2006-01-01

    Full Text Available The total soluble solids content (TSSC shows high positive correlation with sugars content, and therefore is generally accepted as an important quality trait of fruits. In melon, this evaluation is usually done by grinding a slice of the fruit's pulp in a household food processor, straining the ground material and then proceeding the TSSC determination in the resulting juice. This evaluation is labor-intensive and takes a long time to complete. An alternative process was delineated for obtaining the juice: the pulp of the fruit slice would be transversally cut one or more times, and longitudinally pressed by hand to obtain the juice. The objective of this work was to compare processes for obtaining juice to evaluate TSSC in melons. Fifty, 15, and 15 fruits of the Galia, Yellow, and Cantaloupe type melons were evaluated, respectively. Each fruit was considered as a block, and was longitudinally split into six fractions with similar sizes, which corresponded to the plots. The following treatments were evaluated: fraction without cuts, fractions with one, three, five, or seven transversal cuts, and the fraction treated by the conventional process. It was concluded that the procedure by which the melon slices of Galia, Yellow and Cantaloupe types are pressed for obtaining the juice to evaluate TSSC can overestimate this content. This would probably be due to the fact that the most internal section of the mesocarp presents greater TSSC than the portions closer to the epicarp.

  3. Educational opportunities from the SSC

    International Nuclear Information System (INIS)

    Doddy, G.J.; Rider, A.H.; Halff, A.H.

    1990-01-01

    High energy physics and education are very closely interwoven. Most physics laboratories are located at universities or are operated by consortiums of universities. Fermilab and the SSC are operated by the Universities Research Association, URA, a consortium of 69 major research universities and 3 associate members. Another example of this laboratory and universities relationship is the Continuous Electron Beam Accelerator Facility, CEBAF, which is operated by the Southeastern Universities Research Association, SURA, another consortium of 39 major universities. The education potential inherent in the planning, construction and operation of the SSC is immense. The SSC, as the world's largest scientific instrument and, as the most power accelerator, will have a natural attraction as the preeminent institution in the scientific community. In addition to the primary objective of probing the fundamental composition of matter, the SSC will appear to a broad segment of the population and will create the opportunity for both passive and active educational experiences on the part of staff, students and visitors. On the esoteric level, the SSC will be a magnet for the scientific community and will attract from around the world the finest minds in the field of high energy physics. On the human level, the laboratory will become an integral part of the community and will be an object of great interest to local residents and visitors. The SSC planners should recognize the opportunity to be a contributing institution to both the local and the world community

  4. SSC detector solenoid

    International Nuclear Information System (INIS)

    Fast, R.W.; Grimson, J.H.; Kephart, R.D.; Krebs, H.J.; Stone, M.E.; Theriot, E.D.; Wands, R.H.

    1989-01-01

    A detector utilizing a superconducting solenoid is being discussed for the Superconducting Super Collider (SSC). A useful field volume of 8 m diameter x 16 m length at 1.5-2 T (--1 GJ at 2T) is required. It has been decided that all of the particle physics calorimetry will be inside the bore of the solenoid and that there is no need for the coil and cryostat to be ''thin'' in radiation lengths. An iron yoke will reduce the excitation required and will provide muon identification and a redundant momentum measurement of the muons. The authors have developed a conceptual design to meet these requirements. The magnet will use a copper-stabilized Nb-Ti conductor sized for a cryostable pool boiling heat flux --0.025 W/cm/sup 2/. A thermosiphon from a storage vessel above the cryostat will be used to prevent bubble stagnation in the liquid helium bath. The operating current, current density, coil subdivision and dump resistor have been chosen to guarantee that the coil will be undamaged should a quench occur. The axial electromagnetic force will be reacted by metallic support links; the stainless steel coil case will support the radial force. The 5000 metric tons of calorimetry will be supported from the iron yoke through a trussed cylindrical shell structure separate from the cryostat. The coil and case, radiation shield and stainless vacuum vessel would be fabricated and cryogenically tested as two 8-m sections. These would be lowered into the underground experimental hall and installed into the iron flux return yoke to provide the required 16-m length

  5. Scintillating fiber detection development for the SSC

    International Nuclear Information System (INIS)

    Ruchti, R.

    1993-01-01

    SSC Detector Program at Notre Dame has been concentrating on the development of scintillating fiber detectors for tracking applications. Initial work has focused on the development of new scintillation materials for micro-tracking and central tracking detectors based on organic plastics and liquids, This effort has included studies of solvents, solutes and waveguides. Techniques capable of providing the detection of single photons from fibers, are also being developed, leading to a collaboration with Rockwell, UCLA, and UTexas-Dallas groups on the development and application of the Solid State Photomultiplier (SSPM). This initial collaboration has been strengthened and expanded to the formation of a larger collaboration whose goal is to develop a fiber tracking subsystem for SSC, incorporating scintillating fibers and solid state photodetectors. The major subsystem proposal submitted to SSCL by this new collaboration, known at the Fiber Tracking Group (FTG), has been approved and funding is being put in place. The collaboration consists of 12 institutions and Notre Dame is a spokesman group

  6. Forward spectrometers at the SSC

    International Nuclear Information System (INIS)

    Bjorken, J.D.

    1986-01-01

    Most of SSC phase space and a great deal of physics potential is in the forward/backward region (absolute value of theta < 100 mrad). Comprehensive open-geometry spectrometers are feasible and very cost effective. Examples of such devices are sketched. Because such spectrometers are very long and may operate at high β and longer bunch spacing, they impact now on SSC interaction - region design. The data acquisition load is as heavy as for central detectors, although there may be less emphasis on speed and more emphasis on sophisticated parallel and/or distributed processing for event selection, as well as on high-capacity buffering

  7. Design of SSC collider structures

    International Nuclear Information System (INIS)

    Monsees, J.E.

    1994-01-01

    The authors would like to set the record straight. To date, underground construction contracts on the SSC main ring have been bid at a savings of $77 million dollars or 33 percent below the baseline cost estimate. The SSC is the largest single underground project ever built anywhere in the world. When completed it will have approximately 70 miles of tunnels, 60 shafts, two huge underground experiment halls -- each the size of a football stadium -- and numerous other structures, each of which would be considered a major facility on any other project

  8. Simulating supersymmetry at the SSC

    International Nuclear Information System (INIS)

    Barnett, R.M.; Haber, H.E.

    1984-08-01

    Careful study of supersymmetric signatures at the SSC is required in order to distinguish them from Standard Model physics backgrounds. To this end, we have created an efficient, accurate computer program which simulates supersymmetric particle production and decay (or other new particles). We have incorporated the full matrix elements, keeping track of the polarizations of all intermediate states. (At this time hadronization of final-state partons is ignored). Using Monte Carlo techniques this program can generate any desired final-state distribution or individual events for Lego plots. Examples of the results of our study of supersymmetry at SSC are provided

  9. SSC Test Operations Contract Overview

    Science.gov (United States)

    Kleim, Kerry D.

    2010-01-01

    This slide presentation reviews the Test Operations Contract at the Stennis Space Center (SSC). There are views of the test stands layouts, and closer views of the test stands. There are descriptions of the test stand capabilities, some of the other test complexes, the Cryogenic propellant storage facility, the High Pressure Industrial Water (HPIW) facility, and Fluid Component Processing Facility (FCPF).

  10. Ep option at the SSC

    International Nuclear Information System (INIS)

    Prescott, C.Y.

    1984-05-01

    The possibilities for colliding electrons with the 20 TeV proton beams of the SSC are considered. Kinematics of ep colliding beams is reviewed. Energies that may be possible and interesting are suggested, and detector problems associated with the highly imbalanced collisions are briefly considered

  11. Present status and physics prospects of SSC

    International Nuclear Information System (INIS)

    Sugimoto, Shojiro

    1990-01-01

    Physics prospects of Superconducting Super Collider (SSC) are discussed, referring to other coming colliders. In addition, the present status of the SSC project and detector proposals for the experiments are described. (author)

  12. Effects of Moisture Content in Solid Waste Landfills

    National Research Council Canada - National Science Library

    Eck, Craig

    2000-01-01

    Solid waste landfills are an extremely complex and heterogeneous environment. Modeling the biodegradation processes within a landfill must involve an understanding of how environmental factors affect these processes...

  13. 40 CFR Appendix A to Subpart Pppp... - Determination of Weight Volatile Matter Content and Weight Solids Content of Reactive Adhesives

    Science.gov (United States)

    2010-07-01

    ... Content and Weight Solids Content of Reactive Adhesives A Appendix A to Subpart PPPP of Part 63 Protection... Reactive Adhesives 1.0Applicability and Principle 1.1Applicability: This method applies to the... reactive adhesives. Reactive adhesives are composed, in large part, of monomers that react during the...

  14. Computing for an SSC experiment

    International Nuclear Information System (INIS)

    Gaines, I.

    1993-01-01

    The hardware and software problems for SSC experiments are similar to those faced by present day experiments but larger in scale. In particular, the Solenoidal Detector Collaboration (SDC) anticipates the need for close to 10**6 MIPS of off-line computing and will produce several Petabytes (10**15 bytes) of data per year. Software contributions will be made from large numbers of highly geographically dispersed physicists. Hardware and software architectures to meet these needs have been designed. Providing the requisites amount of computing power and providing tools to allow cooperative software development using extensions of existing techniques look achievable. The major challenges will be to provide efficient methods of accessing and manipulating the enormous quantities of data that will be produced at the SSC, and to enforce the use of software engineering tools that will ensure the open-quotes correctnessclose quotes of experiment critical software

  15. Intrinsic Chevrolets at the SSC

    International Nuclear Information System (INIS)

    Brodsky, S.J.; Collins, J.C.; Ellis, S.D.; Gunion, J.F.; Mueller, A.H.

    1984-01-01

    The possibility of the production at high energy of heavy quarks, supersymmetric particles and other large mass colored systems via the intrinsic twist-six components in the proton wave function is discussed. While the existing data do not rule out the possible relevance of intrinsic charm production at present energies, the extrapolation of such intrinsic contributions to very high masses and energies suggests that they will not play an important role at the SSC

  16. Weak interactions at the SSC

    International Nuclear Information System (INIS)

    Chanowitz, M.S.

    1986-03-01

    Prospects for the study of standard model weak interactions at the SSC are reviewed, with emphasis on the unique capability of the SSC to study the mechanism of electroweak symmetry breaking whether the associated new quanta are at the TeV scale or higher. Symmetry breaking by the minimal Higgs mechanism and by related strong interaction dynamical variants is summarized. A set of measurements is outlined that would calibrate the proton structure functions and the backgrounds to new physics. The ability to measure the three weak gauge boson vertex is found to complement LEP II, with measurements extending to larger Q 2 at a comparable statistical level in detectable decays. B factory physics is briefly reviewed as one example of a possible broad program of high statistics studies of sub-TeV scale phenomena. The largest section of the talk is devoted to the possible manifestations of symmetry breaking in the WW and ZZ production cross sections. Some new results are presented bearing on the ability to detect high mass WW and ZZ pairs. The principal conclusion is that although nonstandard model scenarios are typically more forgiving, the capability to study symmetry breaking in the standard model (and in related strong interaction dynamical variants) requires achieving the SSC design goals of √ s,L = 40Tev, 10 33 cm -2 sec -1 . 28 refs., 5 figs

  17. Total cross sections and elastic scattering at the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Foley, K.J.

    1985-12-05

    The need is discussed of a special purpose detector for the measurement of elastic scattering at the SSC. The detector would cover as small a solid angle as is practical. Two techniques are described briefly to measure total cross sections at hadron storage rings. The direct method is to measure the interaction rate in an IR of known luminosity - a method that gets more difficult increasing energy. A second method is to use the optical theorem. 6 refs., 1 fig. (LEW)

  18. Nuclear physical express analysis of solid fuel sulphur content

    International Nuclear Information System (INIS)

    Pak, Yu.; Ponomaryova, M

    2005-01-01

    Full text: Sulphur content is an important qualitative coal parameter. The problem of coal sulphur content determining remains one of the most important both in Kazakhstan and in other coal-mining countries. The traditional method of sampling, the final stage of which is chemical analysis of coal for sulphur, is characterized by high labour intensity and low productivity. That's why it is ineffective for mass express analytical quality control and technological schemes of coal processing control. In this connection it is very urgent to develop a method of coal sulphur content on the base of a series nuclear-geophysical equipment with an isotope source of primary radiation, allowing to increase analysis representativity and maximally take into account coal real composition inconstancy. To solve the problem set it is necessary to study the main laws of X-ray-radiometric method applied to the coal quality analysis for working out instrumental methods of speed determining of coal sulphur content with satisfactory accuracy for technological tasks, to determine laws of changing the flows of characteristic X-ray and scattered radiation from coal sulphur content of various real composition and to optimize methodical and hardware parameters, providing minimal error of sulphur content control. On the base of studying laws of real composition coal components and their interconnections with sulphur content there has been substantiated the expediency of using hardware functions of calcium and iron to control coal sulphur contents; there has been suggested a model to estimate the methodical error of coal sulphur content determining on the base of the data about sensitivity to sulphur and effecting factors using ultimate methods of coal components substitution methods allowing to optimize sulphur control parameters; there has been worked out an algorithm of X-ray-radiometric control of sulphur content based on the sequential radiating the analyzed coal with gamma-radiation of

  19. Kinethical Aspects of High Solid Contents Copoly(Styrene/Butylacrylate-Cloisite 30B Nanocomposites

    Directory of Open Access Journals (Sweden)

    M. Mirzataheri

    2014-01-01

    Full Text Available High solid content poly (styrene-co-butyl acrylate latex ( with 20% and 40% solid content including high amounts of Cloisite 30B (7 wt% and 10 wt% were kinetically investigated. Gravimetric method via measuring the rate of polymerization, number of particles and average number of radicals per particle was used. Results showed that by increasing the solid content; the average diameter of polymer particles decreased. Studies on the polymerization rate depict that the increase in polymer particle size provides more average reactive radicals per polymer particle, which increased from 0.48 to 0.88 for the sample containing 7 wt% clay and 20 wt% solid content. Observed armored particles with honeycomb morphology is the most novelty of this research work, which is suitable for making barrier packaging films.

  20. Predictive relationship between polyphenol and nonfat cocoa solids content of chocolate.

    Science.gov (United States)

    Cooper, Karen A; Campos-Giménez, Esther; Jiménez Alvarez, Diego; Rytz, Andreas; Nagy, Kornél; Williamson, Gary

    2008-01-09

    Chocolate is often labeled with percent cocoa solids content. It is assumed that higher cocoa solids contents are indicative of higher polyphenol concentrations, which have potential health benefits. However, cocoa solids include polyphenol-free cocoa butter and polyphenol-rich nonfat cocoa solids (NFCS). In this study the strength of the relationship between NFCS content (estimated by theobromine as a proxy) and polyphenol content was tested in chocolate samples with labeled cocoa solids contents in the range of 20-100%, grouped as dark (n = 46), milk (n = 8), and those chocolates containing inclusions such as wafers or nuts (n = 15). The relationship was calculated with regard to both total polyphenol content and individual polyphenols. In dark chocolates, NFCS is linearly related to total polyphenols (r2 = 0.73). Total polyphenol content appears to be systematically slightly higher for milk chocolates than estimated by the dark chocolate model, whereas for chocolates containing other ingredients, the estimates fall close to or slightly below the model results. This shows that extra components such as milk, wafers, or nuts might influence the measurements of both theobromine and polyphenol contents. For each of the six main polyphenols (as well as their sum), the relationship with the estimated NFCS was much lower than for total polyphenols (r2 chocolate type, indicating that they might still have some predictive capabilities.

  1. Overview of SSC accelerator requirements

    International Nuclear Information System (INIS)

    Dugan, G.

    1992-03-01

    This paper will present a general overview of the requirements of the Superconducting Super Collider (SSC) accelerators. Each accelerator in the injector chain will be discussed separately, followed by a discussion of the collider itself. In conclusion, the top level requirements of the overall accelerator system will be presented. For each accelerator, the primary operating parameters will be presented in tabular form. A brief narrative discussion of the principal technical features of each machine will be given. Finally, the principal technical design challenges for the machine will be noted, together with the currently planned solution to these challenges

  2. Effect of solids, caloric content on dual-phase gastric emptying

    Energy Technology Data Exchange (ETDEWEB)

    Van Den Maegdenbergh, V.; Urbain, J.L.; Siegel, J.A.; Mortelmans, L.; De Roo, M. (Univ. Hospital Gasthuisberg, Leuven (Belgium) Temple Univ. Hospital, Philadelphia, PA (USA))

    1990-03-01

    The dual-phase gastric emptying technique is routinely employed to determine the differential emptying of solids and liquids in a wide spectrum of gastrointestinal diseases. Composition, acidity, volume, caloric density, physical form and viscosity of the test means have been shown to be important determinants for the quantitative evaluation of gastric emptying. In this study, the authors have evaluated the effect of increasing the caloric content of the solid portion of a physiologic test mean on both solid and liquid emptying kinetics in health male volunteers. They observed that increasing solid caloric content delayed emptying of both solids and liquids. For the solid phase, the delay was accounted for by a longer lag phase and decrease in emptying rate; for liquids a longer emptying rate was also obtained. They conclude that modification of the caloric content of the solid portion of a meal not only affects the emptying of the solid phase but also alters the emptying of the liquid component of the meal.

  3. Dynamic effect of total solid content, low substrate/inoculum ratio and particle size on solid-state anaerobic digestion.

    Science.gov (United States)

    Motte, J-C; Escudié, R; Bernet, N; Delgenes, J-P; Steyer, J-P; Dumas, C

    2013-09-01

    Among all the process parameters of solid-state anaerobic digestion (SS-AD), total solid content (TS), inoculation (S/X ratio) and size of the organic solid particles can be optimized to improve methane yield and process stability. To evaluate the effects of each parameter and their interactions on methane production, a three level Box-Behnken experimental design was implemented in SS-AD batch tests degrading wheat straw by adjusting: TS content from 15% to 25%, S/X ratio (in volatile solids) between 28 and 47 and particle size with a mean diameter ranging from 0.1 to 1.4mm. A dynamic analysis of the methane production indicates that the S/X ratio has only an effect during the start-up phase of the SS-AD. During the growing phase, TS content becomes the main parameter governing the methane production and its strong interaction with the particle size suggests the important role of water compartmentation on SS-AD. Copyright © 2013 Elsevier Ltd. All rights reserved.

  4. Heavy metal content of combustible municipal solid waste in Denmark.

    Science.gov (United States)

    Riber, Christian; Fredriksen, Gry S; Christensen, Thomas H

    2005-04-01

    Data on the heavy metal composition of outlets from Danish incinerators was used to estimate the concentration of Zn, Cu, Pb, Cr, Ni, Cd, As and Hg in combustible waste (wet as received) at 14 Danish incinerators, representing about 80% of the waste incinerated in Denmark. Zn (1020 mg kg(-1)), Cu (620 mg kg(-1)) and Pb (370 mg kg(-1)) showed the highest concentration, whereas Hg (0.6 mg kg(-1)) showed the lowest concentration. The variation among the incinerators was in most cases within a factor of two to three, except for Cr that in two cases showed unexplained high concentrations. The fact that the data represent many incinerators and, in several cases, observations from a period of 4 to 5 years provides a good statistical basis for evaluating the content of heavy metals in combustible Danish waste. Such data may be used for identifying incinerators receiving waste with high concentrations of heavy metals suggesting the introduction of source control, or, if repeated in time, the data must also be used for monitoring the impacts of national regulation controlling heavy metals. It is recommended that future investigations consider the use of sample digestion methods that ensure complete digestion in order to use the data for determining the total heavy metal content of waste.

  5. Accelerator physics issues at the SSC

    International Nuclear Information System (INIS)

    Dugan, G.F.

    1993-05-01

    Realization of the design energy and luminosity goals of the Superconducting Super Collider (SSC) will require proper resolutions of a number of challenging problems in accelerator physics. The status of several salient issues in the design of the SSC will be reviewed and updated in this paper. The emphasis will be on the superconducting accelerators

  6. A GEM of an SSC detector

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    The SSC Laboratory has decided to support the GEM (Gammas, Electrons, and Muons) detector collaboration in the next stage of its work, development of a Technical Design Report. Initial ideas for GEM as the second major SSC detector were aired last year

  7. Commissioning plans for SSC linac

    International Nuclear Information System (INIS)

    Hurd, J.W.; Aprile, R.L.; Chang, C.R.; Crist, C.E.; Cutler, R.I.; Funk, L.W.; Guy, F.W.; Leifeste, G.T.; Raparia, D.; Saadatmand, K.; Sethi, R.C.; Swenson, D.A.; Tooker, J.; Yao, C.G.

    1992-01-01

    Presented are the general description of the SSC linac and the plans for commissioning. Sections of the linac are installed, tested, and beam commissioned in a serial approach. A specialized set of diagnostics is used to characterize the beam through each section. In addition to the standard diagnostic set, plans call for the use of a bunch shape monitor and x-ray spectrometer. Streak camera and digital imaging diagnostics will be developed. The commissioning plan is folded into the general linac project schedule to show the relation between delivery, staging, installation, conditioning, and actual commissioning with beam. These plans form the basis for coordination between the various organizations responsible for different elements of the linac including the technical components, infrastructure, and temporary staging and operation facilities. (Author) 2 figs., 17 refs

  8. Mechanical behavior and microstructure during compression of semi-solid ZK60-RE magnesium alloy at high solid content

    International Nuclear Information System (INIS)

    Shan Weiwei; Luo Shoujing

    2007-01-01

    Mechanical behavior during compression of semi-solid ZK60-RE magnesium alloy at high solid content is researched in this paper. The alloy was prepared from ZK60 alloy and rare earth elements by casting, equal channel angular extruding, and liquidus forging. Semi-solid isothermal pre-treatment was carried out to make the grains globular before the compression. Here, several groups of true strain-true stress curves with different variables during compression are given to make comparisons of their mechanical behaviors. Liquid paths were the most essential to deformation, and its variation during compression depends on the strain rate. Here, thixotropic strength is defined as the true stress at the first peak in the true stress-true strain curve

  9. Effect of solid content variations on PZT slip for tape casting

    Directory of Open Access Journals (Sweden)

    Gang Jian

    2012-12-01

    Full Text Available Lead zirconate titanate (PZT particles with pure tetragonal structure were synthesized by solid-state reaction method and used for preparation of slurries with different solid contents (34–80 wt.%. Then, PZT thick films were fabricated by the nonaqueous tape casting method. It was shown that the slurry prepared from ball-milled particles exhibited better rheology properties than slurry from particles which were not ball-milled. Measurement of sedimentation volumes and zeta potentials indicated particle aggregation, resulting in weak stability of the slurries with high solid contents. The microstructure, piezoelectric and ferroelectric properties of PZT sintered films were investigated in terms of solid contents. Ceramic films prepared from the slurry with solid contents of 73 wt.% had the optimal structure and properties. After poling at 200 °C with an applied field of 1.2 kV/cm, a d33 of 294 pC/N was achieved; typical ferroelectric properties were also observed with a Ps of 38 μC/cm2.

  10. Physics possibilities at LHC/SSC

    International Nuclear Information System (INIS)

    Hinchliffe, I.

    1991-01-01

    This document reviews some recent work on physics simulations for SSC/LHC. Included are reviews of some of the recent developments in physics simulations for the SSC/LHC and comments upon the requirements that are placed upon detectors by the need to extract specific physics signatures. The material in the various EOI/LOI documents submitted to the SCC Laboratory and the work done at the Aachen LHC workshop are discussed. In the following discussion 1 SSC (LHC) year corresponds to an integrated luminosity of 10 (100) fb -1 . 41 refs., 14 figs

  11. Systems engineering and integrated for the SSC

    International Nuclear Information System (INIS)

    Laintz, D.J.; Crosby, B.; Davis, M.; Eben, D.; Gliozzi, J.; Kientz, E.; Knafelc, J.; Phelps, J.; Rider, M.; Shearer, K.

    1989-01-01

    Experience in high technology projects of scale and scope similar to the SSC, leads the authors to propose utilization of a Systems Engineering and Integration (SE and I) process tailored specifically to the SSC project. They begin by giving an overview of SE and I. This overview includes the purpose, history, definition, and a discussion of when to use it. They then proceeded to give a description of a formalized SE and I process. They discuss tailoring the process to a project and close by recommending an early commitment to an SE and I methodology for the SSC. 2 refs., 2 figs

  12. Effect of increasing total solids contents on anaerobic digestion of food waste under mesophilic conditions: performance and microbial characteristics analysis.

    Directory of Open Access Journals (Sweden)

    Jing Yi

    Full Text Available The total solids content of feedstocks affects the performances of anaerobic digestion and the change of total solids content will lead the change of microbial morphology in systems. In order to increase the efficiency of anaerobic digestion, it is necessary to understand the role of the total solids content on the behavior of the microbial communities involved in anaerobic digestion of organic matter from wet to dry technology. The performances of mesophilic anaerobic digestion of food waste with different total solids contents from 5% to 20% were compared and the microbial communities in reactors were investigated using 454 pyrosequencing technology. Three stable anaerobic digestion processes were achieved for food waste biodegradation and methane generation. Better performances mainly including volatile solids reduction and methane yield were obtained in the reactors with higher total solids content. Pyrosequencing results revealed significant shifts in bacterial community with increasing total solids contents. The proportion of phylum Chloroflexi decreased obviously with increasing total solids contents while other functional bacteria showed increasing trend. Methanosarcina absolutely dominated in archaeal communities in three reactors and the relative abundance of this group showed increasing trend with increasing total solids contents. These results revealed the effects of the total solids content on the performance parameters and the behavior of the microbial communities involved in the anaerobic digestion of food waste from wet to dry technologies.

  13. Effect of Increasing Total Solids Contents on Anaerobic Digestion of Food Waste under Mesophilic Conditions: Performance and Microbial Characteristics Analysis

    Science.gov (United States)

    Jin, Jingwei; Dai, Xiaohu

    2014-01-01

    The total solids content of feedstocks affects the performances of anaerobic digestion and the change of total solids content will lead the change of microbial morphology in systems. In order to increase the efficiency of anaerobic digestion, it is necessary to understand the role of the total solids content on the behavior of the microbial communities involved in anaerobic digestion of organic matter from wet to dry technology. The performances of mesophilic anaerobic digestion of food waste with different total solids contents from 5% to 20% were compared and the microbial communities in reactors were investigated using 454 pyrosequencing technology. Three stable anaerobic digestion processes were achieved for food waste biodegradation and methane generation. Better performances mainly including volatile solids reduction and methane yield were obtained in the reactors with higher total solids content. Pyrosequencing results revealed significant shifts in bacterial community with increasing total solids contents. The proportion of phylum Chloroflexi decreased obviously with increasing total solids contents while other functional bacteria showed increasing trend. Methanosarcina absolutely dominated in archaeal communities in three reactors and the relative abundance of this group showed increasing trend with increasing total solids contents. These results revealed the effects of the total solids content on the performance parameters and the behavior of the microbial communities involved in the anaerobic digestion of food waste from wet to dry technologies. PMID:25051352

  14. Effect of increasing total solids contents on anaerobic digestion of food waste under mesophilic conditions: performance and microbial characteristics analysis.

    Science.gov (United States)

    Yi, Jing; Dong, Bin; Jin, Jingwei; Dai, Xiaohu

    2014-01-01

    The total solids content of feedstocks affects the performances of anaerobic digestion and the change of total solids content will lead the change of microbial morphology in systems. In order to increase the efficiency of anaerobic digestion, it is necessary to understand the role of the total solids content on the behavior of the microbial communities involved in anaerobic digestion of organic matter from wet to dry technology. The performances of mesophilic anaerobic digestion of food waste with different total solids contents from 5% to 20% were compared and the microbial communities in reactors were investigated using 454 pyrosequencing technology. Three stable anaerobic digestion processes were achieved for food waste biodegradation and methane generation. Better performances mainly including volatile solids reduction and methane yield were obtained in the reactors with higher total solids content. Pyrosequencing results revealed significant shifts in bacterial community with increasing total solids contents. The proportion of phylum Chloroflexi decreased obviously with increasing total solids contents while other functional bacteria showed increasing trend. Methanosarcina absolutely dominated in archaeal communities in three reactors and the relative abundance of this group showed increasing trend with increasing total solids contents. These results revealed the effects of the total solids content on the performance parameters and the behavior of the microbial communities involved in the anaerobic digestion of food waste from wet to dry technologies.

  15. A study of the metal content of municipal solid waste. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Churney, K.L.; Domalski, E.S.

    1998-01-01

    Knowledge of the content of toxic components, so called pollutant precursors, in the municipal solid waste (MSW) stream is essential to development of the strategies for source reduction and reuse, recycling, composting and disposal. Data are scarce; trends in composition for any locality even more so. In a previous study the total and water soluble chlorine content of the components of municipal solid waste were determined from sampling studies at two sites, Baltimore County, MD, and Brooklyn, NY, each for a five day period. The total sulfur content of the combined combustible components was also determined. Because of the scarcity of data and synergistic effects, it seemed appropriate to determine the heavy metal content of the preceding material prior to its disposal. The metals chosen were the so-called priority pollutant metals (PPM): antimony, arsenic, beryllium, cadmium, chromium, copper, lead, mercury, nickel, selenium, silver, thallium, and zinc.

  16. Examinations of content of heavy metals in municipal solid waste and produced compost

    International Nuclear Information System (INIS)

    Golimowski, J.; Tykarska, A.; Orzechowska, K.

    1993-01-01

    The basic methods of utilization of municipal solid waste are biothermic and aerobic methods to compost. The content of heavy metals in composts depends on the initial their content in wastes as well as on the compost process. The voltammetric method has been applied for measurement of concentration of Zn, Cd, Pb, Cu, Cr, Ni and Hg in the waste and composts samples. (author). 24 refs, 2 figs, 3 tabs

  17. Detector problems at the SSC

    International Nuclear Information System (INIS)

    Wojcicki, S.G.

    1985-02-01

    During the last couple of years there has been considerable concern expressed among the US high energy community as to whether detector limitations would prevent one from being able to fully exploit a luminosity of 10 33 cm -2 sec -1 at a hadron-hadron high energy collider. As a result of these concerns, a considerable amount of work has been done recently in trying to understand the nature of potential difficulties and the required R and D that needs to be performed. A lot of this work has been summarized in the 1984 DPF Summer Study at Snowmass. This paper attempts to review some of these results. This work is limited to the discussion of detector problems associated with the study of high energy hadron-hadron collisions. We shall start with the discussion of the desirable features of the detectors and of the SSC environment in which they will have to work. After a brief discussion of the model 4π detectors, we shall discuss specific detector aspects: lepton identification, tracking, calorimetry and computing and triggering. We shall end with some remarks about possible future course of events. 15 refs., 10 figs

  18. Measuring structure functions at SSC energies

    International Nuclear Information System (INIS)

    Morfin, J.G.; Owens, J.F.

    1985-01-01

    Topics discussed include measuring Λ, tests of QCD using hard scattering processes, and measuring parton distributions. In each case, any opportunities and advantages afforded by the unique features of the SSC are emphasized. The working group on structure functions was charged with investigating two specific questions: (1) How well are the various parton distributions known in the kinematic region relevant to calculations for the SSC. (2) What new information can be learned about parton distributions at the SSC. Especially for this working group, the advantages of having a fixed-target facility at the SSC for the measurement of the parton distributions with multi-TeV leptons, were to be examined. 15 references

  19. Decoupling schemes for the SSC Collider

    International Nuclear Information System (INIS)

    Cai, Y.; Bourianoff, G.; Cole, B.; Meinke, R.; Peterson, J.; Pilat, F.; Stampke, S.; Syphers, M.; Talman, R.

    1993-05-01

    A decoupling system is designed for the SSC Collider. This system can accommodate three decoupling schemes by using 44 skew quadrupoles in the different configurations. Several decoupling schemes are studied and compared in this paper

  20. Physics motivations for SSC/LHC detectors

    International Nuclear Information System (INIS)

    Hinchliffe, I.

    1993-06-01

    In this talk, I review the some of the physics goals and simulation work done in the SSC and LHC experimental proposal. I select the processes that illustrate the strengths and weaknesses the proposed detectors

  1. Effects of Sludge Dry Solid Content and Residual Bulking Agents on Volatile Solids Reduction Using Eisenia foetida

    Directory of Open Access Journals (Sweden)

    Mohammad ali Abdoli

    2009-06-01

    Full Text Available In the first stage of this study, the compound effects of sludge dry solid content and residual bulking agent type (paper, saw dust, straw mixed with activated sludge (10, 15, and 20% dry solids on volatile solids (V.S. reduction were investigated using Eisenia foetida in pilot scale experiments with batches of fifty earthworms in each of the 10 experimental treatments over a period of 10 weeks. The maximum V.S. reduction was attained in the mixture of sludge and paper, with a D.S. of 15% (0.42 ± 0.03 % day-1 while the minimum V.S. reduction was achieved in the mixture of sludge and straw, with a D.S. of 10% (0.26 ± 0.01 % day-1. In the second stage, the survival of Eisenia foetida in the anaerobic sewage sludge was investigated. In the unmixed raw anaerobic sludge, all the earthworms died during the first 9 weeks of the study period due to acute toxicity. From week 10, however, their survival rate improved so that by week 12 when toxicity reduced to 25.40%, they completely survived. This is while in the mixture of anaerobic sludge with paper (D.S. 15%, 100% of the earthworms survived from week 8 after the volatile solids reduced to 20.42% and 17.40%.

  2. Effect of Increasing Total Solids Contents on Anaerobic Digestion of Food Waste under Mesophilic Conditions: Performance and Microbial Characteristics Analysis

    OpenAIRE

    Yi, Jing; Dong, Bin; Jin, Jingwei; Dai, Xiaohu

    2014-01-01

    The total solids content of feedstocks affects the performances of anaerobic digestion and the change of total solids content will lead the change of microbial morphology in systems. In order to increase the efficiency of anaerobic digestion, it is necessary to understand the role of the total solids content on the behavior of the microbial communities involved in anaerobic digestion of organic matter from wet to dry technology. The performances of mesophilic anaerobic digestion of food waste...

  3. SSC-K code user's manual

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Y M; Lee, Y B; Chang, W P; Hahn, D

    2000-07-01

    The Supper System Code of KAERI (SSC-K) is a best-estimate system code for analyzing a variety of off-normal or accidents in the heat transport system of a pool type LMR design. It is being developed at Korea Atomic Energy Research Inititution (KAERI) on the basis of SSC-L, originally developed at BNL to analyze loop-type LMR transients. SSC-K can handle both designs of loop and pool type LMRs. SSC-K contains detailed mechanistic models of transient thermal, hydraulic, neutronic, and mechanical phenomena to describe the response of the reactor core, coolant, fuel elements, and structures to accident conditions. This report provides an overview of recent model developmentsvfor the SSC-K computer code, focusing on phenomenological model descriptions for new thermal, hydraulic, neutronic, and mechnaical modules. A comprehensive description of the models for pool-type reactor is given in Chapters 2 and 3; the steady-state plant characterization, prior to the initiation of transient is described in Chapter 2 and their transient counterparts are discussed in Chapter 3. In Chapter 4, a discussion on the intermediate heat exchanger (IHX) is presented. The IHX model of SSC-K is similar to that used in the SSC-L, except for some changes required for the pool-type configuration of reactor vessel. In Chapter 5, an electromagnetic (EM) pump is modeled as a component. There are two pump choices available in SSC-K; a centrifugal pump which was originally imbedded into the SSC-L, and an EM pump which was introduced for the KALIMER design. In Chapter 6, a model of passive safety decay heat removal system(PSDRS) is discussed, which removes decay heat through the reactor and containment vessel walls to the ambient air heat sink. In Chapter 7, models for various reactivity feedback effects are discussed. Reactivity effects of importance in fast reactor include the Doppler effect, effects of sodium density changes, effects of dimensional changes in core geometry. Finally in Chapter 8

  4. Tracking with wire chambers at the SSC

    International Nuclear Information System (INIS)

    Hanson, G.G.; Gundy, M.C.; Palounek, A.P.T.

    1989-07-01

    Limitations placed on wire chambers by radiation damage and rate requirements in the SSC environment are reviewed. Possible conceptual designs for wire chamber tacking systems that meet these requirements are discussed. Computer simulation studies of tracking in such systems are presented. Simulations of events from interesting physics at the SSC, including hits from minimum bias background events, are examined. Results of some preliminary pattern recognition studies are given. 13 refs., 11 fig., 1 tab

  5. Solid fat content as a substitute for total polar compound analysis in edible oils

    Science.gov (United States)

    The solid fat contents (SFC) of heated edible oil samples were measured and found to correlate positively with total polar compounds (TPC) and inversely with triglyceride concentration. Traditional methods for determination of total polar compounds require a laboratory setting and are time intensiv...

  6. Synthesis and properties of hydroxy acrylic resin with high solid content

    Science.gov (United States)

    Yu, Zhen; Hu, Mingguang; Cui, Han; Xiao, Jijun

    2017-10-01

    Manufacturers of automotive repair finishes are tending to reduce more and more the level of volatile organic compounds in their paints in order to comply with increasingly strict environmental legislation. A high solid hydroxy acrylic resin was synthesised using CARDURA E10 and a type of hydroxyacrylic acid resin, its' acid value, hydroxylvalue, viscosity, structure, morphology was measured and film-forming properties after curing were characterised. The results show that the addition of CARDURA E10 in the copolymer composition significantly reduced the viscosity of the polymer system, improved the solid content of the resin and the physical properties of the coating. The hydroxyl acrylate resin with solid content of 90% and excellent comprehensive performance were successfully prepared by controlling the initiator dosage, polymerization temperature and monomer ratio.

  7. Validation of SSC using the FFTF natural-circulation tests

    International Nuclear Information System (INIS)

    Horak, W.C.; Guppy, J.G.; Kennett, R.J.

    1982-01-01

    As part of the Super System Code (SSC) validation program, the 100% power FFTF natural circulation test has been simulated using SSC. A detailed 19 channel, 2 loop model was used in SSC. Comparisons showed SSC calculations to be in good agreement with the Fast Flux Test Facility (FFTF), test data. Simulation of the test was obtained in real time

  8. High Solid Contents Copoly (Styrene/Butyl Acrylate-Cloisite 30B Nanocomposites

    Directory of Open Access Journals (Sweden)

    M. Mirzataheri

    2013-03-01

    Full Text Available Higher solid contents (20 % and 40 % nanocomposites of poly (styrene-co-butyl acrylate including higher content of Cloisite 30B (7 wt% and 10 wt % were prepared via miniemulsion polymerization. Stability of the final latexes proved outstanding combination of polymerization procedure and surfactants. Morphological studies revealed by TEM, SAX and XRD showed three structures of core-shell, armored and individual dispersion of clay layers within the polymer particles. The effect of Cloisite 30B content on the barrier properties presents excellent and wide use of these films for packaging and nanocoatings industries.

  9. Stress relaxation in SSC 50mm dipole coils

    International Nuclear Information System (INIS)

    Rogers, D.; Markley, F.

    1992-04-01

    We are measuring the stress relaxation of SSC 50mm outer coils with the goal of predicting how much of the coil prestress will be lost while the coils are warehoused between manufacture and cooldown. We manufacture 3 inch (76.2mm) long segments of coil with the same materials and techniques that have been used for prototype coils. We are running four simultaneous tests in an attempt to separate the contributions of the different coil materials. Test one is a completely insulated coil section where the insulation is the all polyamide system being tested at Brookhaven; test two is a wire stack insulated only with the normal Kapton overwrap; test three is a stack of bare cable; and test four is a completely insulated normal coil section. All, except for the bare cable, include the ground insulation. The insulated coil sections are carefully dried before loading and testing in order to eliminate stress changes due to varying moisture content. The temperature dependence of the stress relaxation is being studied separately. Three companion papers presented at this conference will be: (1) ''Temperature dependence of the viscoelastic properties of SSC coil insulation'' (2) ''Measurement of the elastic modulus of Kapton perpendicular to the plane of the film at room and cryogenic temperatures'' (3) ''Theoretical methods for creep and stress relaxation studies of SSC coil.''

  10. Solid state fermentation of Trichoderma viride for enhancement phenolic content, antioxidant and antimicrobial activities in ginger.

    Science.gov (United States)

    Saleh, Rashad M; Kabli, Saleh A; Al-Garni, Saleh M; Al-Ghamdi, Maryam A; Abdel-Aty, Azza M; Mohamed, Saleh A

    2018-05-04

    The phenolic content of methanolic and water extracts of ginger fermented by Trichoderma spp. during solid state fermentation (SSF) was detected as compared with unfermented ginger. The total phenolic content of fermented ginger increased several times. The highest phenolic content of ginger was detected after SSF by T. viride. The optimal physiological conditions for the maximum production of the phenolic content and β-glucosidase activity of fermented ginger by T. viride were detected at day 7 incubation, pH 6.0, 30°C and 30% moisture. There are consistent between the maximum production of β-glucosidase and phenolic content. The SSF of ginger by T. viride greatly enhanced the antioxidant potency of phenolic compounds by using DPPH and ABTS assays. Potent antibacterial activity was appeared by phenolic compounds of fermented ginger against all the tested human-pathogenic bacteria. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

  11. SSC [Superconducting Super Collider] site evaluations

    International Nuclear Information System (INIS)

    1988-11-01

    With this report, the SSC Site Task Force forwards to the Director, Office of Energy Research, US Department of Energy (DOE), its evaluation of the technical criteria and life-cycle costs for the proposed SSC sites judged to be the best qualified. The criteria against which each site was evaluated are those set forth in the Invitation for Site Proposals for the Superconducting Super Collider (DOE/ER-0315) (Invitation) which was prepared by the Task Force and issued in April 1987. The methodology followed by the Task Force in this report and in all other phases of the proposal evaluation has been consistent with the SSC site selection process approved by DOE's Energy System Acquisition Advisory Board (ESAAB). The goal of the site selection process is to identify a site that will permit the highest level of research productivity and overall effectiveness of the SSC at a reasonable cost of construction and operation and with minimial impact on the environment. The Task Force acknowledges that all seven sites are, indeed, highly qualified locations for the construction and operation of the SSC on the basis of technical and cost considerations. In performing its evaluation, which is presented in this paper, the Task Force took an in-depth look at each site on the basis of site visits and extensive technical analyses. A consensus rating for each technical evaluation criterion and subcriterion was developed for each site

  12. Effects of residues from municipal solid waste landfill on corn yield and heavy metal content

    International Nuclear Information System (INIS)

    Prabpai, S.; Charerntanyarak, L.; Siri, B.; Moore, M.R.; Noller, Barry N.

    2009-01-01

    The effects of residues from municipal solid waste landfill, Khon Kaen Municipality, Thailand, on corn (Zea mays L.) yield and heavy metal content were studied. Field experiments with randomized complete block design with five treatments (0, 20, 40, 60 and 80% v/v of residues and soil) and four replications were carried out. Corn yield and heavy metal contents in corn grain were analyzed. Corn yield increased by 50, 72, 85 and 71% at 20, 40, 60 and 80% treatments as compared to the control, respectively. All heavy metals content, except cadmium, nickel and zinc, in corn grain were not significantly different from the control. Arsenic, cadmium and zinc in corn grain were strongly positively correlated with concentrations in soil. The heavy metal content in corn grain was within regulated limits for human consumption.

  13. Remote operation of microwave systems for solids content analysis and chemical dissolution in highly radioactive environments

    International Nuclear Information System (INIS)

    Sturcken, E.F.; Floyd, T.S.; Manchester, D.P.

    1986-10-01

    Microwave systems provide quick and easy determination of solids content of samples in high-level radioactive cells. In addition, dissolution of samples is much faster when employing microwave techniques. These are great advantages because work in cells,using master-slave manipulators through leaded glass walls, is normally slower by an order of magnitude than direct contact methods. This paper describes the modifiction of a moisture/solids analyzer microwave system and a drying/digestion microwave system for remote operation in radiation environments. The moisture/solids analyzer has operated satisfactorily for over a year in a gamma radiation field of 1000 roentgens per hour and the drying/digestion system is ready for installation in a cell

  14. Fast Measurement of Soluble Solid Content in Mango Based on Visible and Infrared Spectroscopy Technique

    Science.gov (United States)

    Yu, Jiajia; He, Yong

    Mango is a kind of popular tropical fruit, and the soluble solid content is an important in this study visible and short-wave near-infrared spectroscopy (VIS/SWNIR) technique was applied. For sake of investigating the feasibility of using VIS/SWNIR spectroscopy to measure the soluble solid content in mango, and validating the performance of selected sensitive bands, for the calibration set was formed by 135 mango samples, while the remaining 45 mango samples for the prediction set. The combination of partial least squares and backpropagation artificial neural networks (PLS-BP) was used to calculate the prediction model based on raw spectrum data. Based on PLS-BP, the determination coefficient for prediction (Rp) was 0.757 and root mean square and the process is simple and easy to operate. Compared with the Partial least squares (PLS) result, the performance of PLS-BP is better.

  15. A fixed target facility at the SSC

    International Nuclear Information System (INIS)

    Loken, S.; Morfin, J.G.

    1984-01-01

    The question of whether a facility for fixed target physics should be provided at the SSC must be answered before the final technical design of the SSC can be completed, particularly if the eventual form of extraction would influence the magnet design. To this end, an enthusiastic group of experimentalists, theoreticians and accelerator specialists have studied this point. The accelerator physics issues were addressed by a group whose report is contained in these proceedings. The physics addressable by fixed target was considered by many of the Physics area working groups and in particular by the Structure Function Group. This report is the summary of the working group which considered various SSC fixed target experiments and determined which types of beams and detectors would be required

  16. Fixed target facility at the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Loken, S.C.; Morfin, J.G.

    1985-01-01

    The question of whether a facility for fixed target physics should be provided at the SSC must be answered before the final technical design of the SSC can be completed, particularly if the eventual form of extraction would influence the magnet design. To this end, an enthusiastic group of experimentalists, theoreticians and accelerator specialists have studied this point. The accelerator physics issues were addressed by a group led by E. Colton whose report is contained in these proceedings. The physics addressable by fixed target was considered by many of the Physics area working groups and in particular by the Structure Function Group. This report is the summary of the working group which considered various SSC fixed target experiments and determined which types of beams and detectors would be required. 13 references, 5 figures.

  17. Fixed target facility at the SSC

    International Nuclear Information System (INIS)

    Loken, S.C.; Morfin, J.G.

    1985-01-01

    The question of whether a facility for fixed target physics should be provided at the SSC must be answered before the final technical design of the SSC can be completed, particularly if the eventual form of extraction would influence the magnet design. To this end, an enthusiastic group of experimentalists, theoreticians and accelerator specialists have studied this point. The accelerator physics issues were addressed by a group led by E. Colton whose report is contained in these proceedings. The physics addressable by fixed target was considered by many of the Physics area working groups and in particular by the Structure Function Group. This report is the summary of the working group which considered various SSC fixed target experiments and determined which types of beams and detectors would be required. 13 references, 5 figures

  18. Artificial Neural Network Modelling of the Energy Content of Municipal Solid Wastes in Northern Nigeria

    Directory of Open Access Journals (Sweden)

    M. B. Oumarou

    2017-12-01

    Full Text Available The study presents an application of the artificial neural network model using the back propagation learning algorithm to predict the actual calorific value of the municipal solid waste in major cities of the northern part of Nigeria, with high population densities and intense industrial activities. These cities are: Kano, Damaturu, Dutse, Bauchi, Birnin Kebbi, Gusau, Maiduguri, Katsina and Sokoto. Experimental data of the energy content and the physical characterization of the municipal solid waste serve as the input parameter in nature of wood, grass, metal, plastic, food remnants, leaves, glass and paper. Comparative studies were made by using the developed model, the experimental results and a correlation which was earlier developed by the authors to predict the energy content. While predicting the actual calorific value, the maximum error was 0.94% for the artificial neural network model and 5.20% by the statistical correlation. The network with eight neurons and an R2 = 0.96881 in the hidden layer results in a stable and optimum network. This study showed that the artificial neural network approach could successfully be used for energy content predictions from the municipal solid wastes in Northern Nigeria and other areas of similar waste stream and composition.

  19. First beam extracted from the SSC

    International Nuclear Information System (INIS)

    Anon.

    1986-01-01

    On the 25th July 1986 the first 2,8 μA 66 MeV proton beam was successfully extracted from the separated sector cyclotron (SSC) at the National Accelerator Centre at Faure, South Africa. The beam has now also been transported for the first time down the high-energy beamline up to the last Faraday cup in front of the neutron therapy vault. A brief description of the extraction system of the SSC, consisting of an electrostatic extraction channel and two septum magnets is given

  20. Highlights of the SSC Site Development Plan

    International Nuclear Information System (INIS)

    Sanford, J.R.

    1991-10-01

    This paper summarizes highlights of the Site Development Plan for the Superconducting Super Collider Laboratory. The Plan, sometimes called a Master Plan, was prepared by the architectural and engineering firm for the Laboratory: Parsons Brinckerhoff/Morrison Knudsen (PB/MK) working in association with CRSS. Their task was to interpret the SSC project needs in the context of the Ellis County, Texas site. The team effort was under the direction of Lewis May from CRSS, guided by Robert Sims from the SSC Laboratory. Conceptual drawings are presented in this report

  1. Analysis and design of SSC underground structures

    International Nuclear Information System (INIS)

    Clark, G.T.

    1993-01-01

    This paper describes the analysis and design of underground structures for the Superconducting Super Collider (SSC) Project. A brief overview of the SSC Project and the types of underground structures are presented. Engineering properties and non-linear behavior of the geologic materials are reviewed. The three-dimensional sequential finite element rock-structure interaction analysis techniques developed by the author are presented and discussed. Several examples of how the method works, specific advantages, and constraints are presented. Finally, the structural designs that resulted from the sequential interaction analysis are presented

  2. Analytical solutions to SSC coil end design

    International Nuclear Information System (INIS)

    Bossert, R.C.; Brandt, J.S.; Carson, J.A.; Fulton, H.J.; Lee, G.C.; Cook, J.M.

    1989-03-01

    As part of the SCC magnet effort, Fermilab will build and test a series of one meter model SSC magnets. The coils in these magnets will be constructed with several different end configurations. These end designs must satisfy both mechanical and magnetic criteria. Only the mechanical problem will be addressed. Solutions will attempt to minimize stresses and provide internal support for the cable. Different end designs will be compared in an attempt to determine which is most appropriate for the SSC dipole. The mathematics required to create each end configuration will be described. The computer aided design, programming and machine technology needed to make the parts will be reviewed. 2 refs., 10 figs

  3. A data acquisition architecture for the SSC

    International Nuclear Information System (INIS)

    Partridge, R.

    1990-01-01

    An SSC data acquisition architecture applicable to high-p T detectors is described. The architecture is based upon a small set of design principles that were chosen to simplify communication between data acquisition elements while providing the required level of flexibility and performance. The architecture features an integrated system for data collection, event building, and communication with a large processing farm. The interface to the front end electronics system is also discussed. A set of design parameters is given for a data acquisition system that should meet the needs of high-p T detectors at the SSC

  4. Compensation of coupling in the SSC complex

    International Nuclear Information System (INIS)

    Pilat, F.; Bourianoff, G.

    1991-10-01

    This paper will describe a study of the coupling effects and their compensation by means of local depending techniques for some of the accelerators in the SSC Complex. Results concerning corrections and decoupling for the Low Energy and Medium Energy Boosters will be compared to results obtained for the Collider Ring. Some preliminary experimental data about measurement of coupling quantities will also be presented

  5. Liquid argon calorimetry for the SSC

    International Nuclear Information System (INIS)

    Gordon, H.A.

    1990-01-01

    Liquid argon calorimetry is a mature technique. However, adapting it to the challenging environment of the SSC requires a large amount of R ampersand D. The advantages of the liquid argon approach are summarized and the issues being addressed by the R ampersand D program are described. 18 refs

  6. Heavy particle production at the SSC

    International Nuclear Information System (INIS)

    Brodsky, S.J.; Haber, H.E.; Gunion, J.F.

    1984-03-01

    Predictions for the production of heavy quarks, supersymmetric particles, and other colored systems at high energy due to intrinsic twist-six components in the proton wavefunction are given. We also suggest the possibility of using asymmetric collision energies (e.g., via intersecting rings at the SSC) in order to facilitate the study of forward and diffractive particle production processes. 9 references

  7. Electron beam emittance monitor for the SSC

    International Nuclear Information System (INIS)

    Tsyganov, E.; Meinke, R.; Nexsen, W.; Kauffmann, S.; Zinchenko, A.; Taratin, A.

    1993-05-01

    A nondestructive beam profile monitor for the Superconducting Super Collider (SSC) is presented using as a probe a low-energy electron beam interacting with the proton bunch charge. Results using a full Monte Carlo simulation code look promising for the transverse and longitudinal beam profile measurements

  8. Dicty_cDB: SSC474 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available SS (Link to library) SSC474 (Link to dictyBase) - - - Contig-U07719-1 SSC474P (Link... to Original site) SSC474F 368 SSC474Z 238 SSC474P 606 - - Show SSC474 Library SS (Link to library) Clone ID SSC474 (Link to dict...yBase) Atlas ID - NBRP ID - dictyBase ID - Link to Contig Contig-U07719-1 Original site URL http://dict...logy vs DNA Score E Sequences producing significant alignments: (bits) Value N ( AU071762 ) Dictyostelium di...scoideum slug cDNA, clone SSC474. 448 e-121 1 ( AU060185 ) Dictyostelium discoideum slug cDNA, clone SLA535.

  9. SSC beam dynamics scaled to the Eloisatron

    International Nuclear Information System (INIS)

    Ritson, D.

    1992-03-01

    As crosssections drop as E -2 a desirable target for a 100 TeV the Eloisatron would be to achieve luminosities ∼1.10 35 cm 2 /sec. To understand the impact of such an objective we have compared parameters for the SSC and Eloisatron to differentiate areas which involve considerable extrapolations from current technologies from those which represent more conventional scale-ups. Synchrotron radiation losses per m for the same guide magnetic field associated with such luminosities would be up by E 2 x I where E is the energy and I is the circulating current. This would result in energy densities of ∼250 times the nominal SSC values. The SSC is already limited by installed refrigeration power and if the circulating current was to be increased would have to use liners at liquid nitrogen temperatures to intercept the radiation as is proposed for the LHC. This issue was the subject of lively discussion at the workshop and is dealt with elsewhere by other authors. This author believed that the radiation could be intercepted by room temperature catchers spaced every 15--25 m around the ring. To obtain the requisite luminosities it assumes similar bunch spacing but circulating currents an order of magnitude larger than at the SSC. The SSC already uses a bunch spacing as small as 5 m and further reduction does not appear easy. The justification for the choice of bore for the magnets, emittances and attainable luminosities are discussed below. A further section looks into whether seismic ground disturbances might cause unacceptable emittance growth. The conclusion of this section is that careful use of current design practices should be adequate and that it is unlikely that exotic vibration free mounts will be required

  10. Assessment of the content of arsenic in solid by-products from coal combustion

    Directory of Open Access Journals (Sweden)

    Wierońska Faustyna

    2017-01-01

    Full Text Available The coal combustion processes constitute one of the major sources of heavy metals emission into the atmosphere. From the point of view of the reduction of the emission of heavy metals and the selection of the correct exhaust gas treatment system, it is important to monitor the amount of trace elements in the solid fuels and in the solid by-products from coal combustion. One of these highly toxic elements is arsenic. The average content of arsenic in Polish hard coals and lignites is 0 ÷ 40 mg/kg [1] and 5 ÷ 15 mg/kg [2], respectively. The world average content of arsenic in hard coals and lignites, is equal to 9.0 ± 0.8 and 7.4 ± 1.4 mg/kg [3], respectively. During coal combustion processes, a significant amount of arsenic enters the atmosphere through gases and fly ashes. The proportions in which those two forms of arsenic occur in exhaust gases depend on the conditions of combustion processes [4]. The aim of the research was to determine the content of arsenic in coal blends and by-products of their combustion (slag, fly ash, gypsum, filter cakes. The determination of the arsenic quantity was performed using the Atomic Absorption Spectrometry with the electrothermal atomization.

  11. Moisture content determination in solid biofuels by dielectric and NIR reflection methods

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, Peter Daugbjerg; Morsing, Merete [Department of Forest and Landscape, The Royal Veterinary and Agricultural University, Rolighedsvej 23, DK-1958 Frederiksberg C (Denmark); Hartmann, Hans; Boehm, Thorsten [Technologie- und Foerderzentrum fuer Nachwachsende Rohstoffe (TFZ), Schulgasse 18, D-94315 Straubing (Germany); Temmerman, Michael; Rabier, Fabienne [Departement Genie Rural, Chee de Namur 146, B-5030 Gembloux (Belgium)

    2006-11-15

    One near infrared (NIR) reflectance and five dielectric moisture meters were tested for their capability of measuring moisture content (MC) in solid biofuels. Ninety-eight samples were tested at up to eight moisture levels covering the MC range from fresh fuel to approximately 10% MC (w.b.). The fuel types ranged from typical solid biofuels such as coniferous and deciduous wood chips over short rotation coppice (SRC) to sunflower seed and olive stones. The most promising calibrations were obtained with the NIR reflection method and two dielectric devices where the sample is placed in a container integrated in the device. The calibration equations developed show that there is a profound influence from both laboratory and fuel type. It is suggested that individual calibrations that are based on the specific fuel types used at the individual heating plant could be applied. (author)

  12. Fast characterization of solid organic waste content with near infrared spectroscopy in anaerobic digestion.

    Science.gov (United States)

    Charnier, Cyrille; Latrille, Eric; Jimenez, Julie; Lemoine, Margaux; Boulet, Jean-Claude; Miroux, Jérémie; Steyer, Jean-Philippe

    2017-01-01

    The development of anaerobic digestion involves both co-digestion of solid wastes and optimization of the feeding recipe. Within this context, substrate characterisation is an essential issue. Although it is widely used, the biochemical methane potential is not sufficient to optimize the operation of anaerobic digestion plants. Indeed the biochemical composition in carbohydrates, lipids, proteins and the chemical oxygen demand of the inputs are key parameters for the optimisation of process performances. Here we used near infrared spectroscopy as a robust and less-time consuming tool to predict the solid waste content in carbohydrates, lipids and nitrogen, and the chemical oxygen demand. We built a Partial Least Square regression model with 295 samples and validated it with an independent set of 46 samples across a wide range of solid wastes found in anaerobic digestion units. The standard errors of cross-validation were 90mgO 2 ⋅gTS -1 carbohydrates, 2.5∗10 -2 g⋅gTS -1 lipids, 7.2∗10 -3 g⋅gTS -1 nitrogen and 99mgO 2 ⋅gTS -1 chemical oxygen demand. The standard errors of prediction were 53mgO 2 ⋅gTS -1 carbohydrates, 3.2∗10 -2 g⋅gTS -1 lipids, 8.6∗10 -3 g⋅gTS -1 nitrogen and 83mgO 2 ⋅gTS -1 chemical oxygen demand. These results show that near infrared spectroscopy is a new fast and cost-efficient way to characterize solid wastes content and improve their anaerobic digestion monitoring. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Dicty_cDB: SSC836 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available SS (Link to library) SSC836 (Link to dictyBase) - - - - SSC836E (Link to Original s...ite) - - - - - - SSC836E 502 Show SSC836 Library SS (Link to library) Clone ID SSC836 (Link to dictyBase) Atlas ID - NBRP ID - dict...yBase ID - Link to Contig - Original site URL http://dictycdb.biol.tsukuba.ac.jp/CSM/...t alignments: (bits) Value N M77492 |M77492.1 Dictyostelium discoideum glycoprotein phosphorylase 2 (glpD) g...ene, complete cds. 779 0.0 1 AC116984 |AC116984.2 Dictyostelium discoideum chromo

  14. Scintillating fiber detector development for the SSC: Annual progress report

    International Nuclear Information System (INIS)

    Ruchti, R.C.

    1989-01-01

    During the past year, considerable effort has been applied to the development of scintillating fiber detectors in several areas: new scintillation liquids and studies of their fluorescence properties; new fluorescent dyes based on non-intramolecular proton transfer; new dyes based on intramolecular proton transfer; incorporation of these new dyes in plastic (polystyrene) and liquid scintillation solutions; development of small cross section glass capillaries for the containment of liquid scintillators; studies of waveguide characteristics; studies of image intensifier phosphor screen characteristics; initial steps to form a collaboration to study and develop appropriate new properties of the Solid State Photomultiplier; construction of a new laboratory at Notre Dame to enhance our capabilities for further measurements and studies; and organization of and execution of a Workshop on Scintillating Fiber Detector Development for the SSC, held at Fermilab, November 14--16, 1988

  15. System engineering in the SSC Linac

    International Nuclear Information System (INIS)

    Tooker, J.F.; Chang, C.R.; Cutler, R.I.; Funk, L.W.; Guy, F.W.; Hale, R.; Leifeste, G.T.; Nonte, J.; Prichard, B.; Raparia, D.; Saadatmand, K.; Sethi, R.C.; Yao, C.G.

    1992-01-01

    The design and construction of the SSC Linac involves various departments within the SSCL and many outside vendors. The adaptive incorporation of system engineering principles into the SSC Linac is described. This involves the development of specification trees with the breakdown and flow of functional and physical requirements from the top level system specifications to the lower level component specifications. Interfaces are defined, which specify and control the interconnections between the various components. Review cycles are presented during which the requirements, evolution of the design, and test plans are reviewed, monitored, and finalized. The Linac specification tree, interface definition, and reviews of the Linac are presented, including typical examples. (Author) 2 refs., 3 tabs

  16. Magnetic field decay in model SSC dipoles

    International Nuclear Information System (INIS)

    Gilbert, W.S.; Althaus, R.F.; Barale, P.J.; Benjegerdes, R.W.; Green, M.A.; Green, M.I.; Scanlan, R.M.

    1988-08-01

    We have observed that some of our model SSC dipoles have long time constant decays of the magnetic field harmonics with amplitudes large enough to result in significant beam loss, if they are not corrected. The magnets were run at constant current at the SSC injection field level of 0.3 tesla for one to three hours and changes in the magnetic field were observed. One explanation for the observed field decay is time dependent superconductor magnetization. Another explanation involves flux creep or flux flow. Data are presented on how the decay changes with previous flux history. Similar magnets with different Nb-Ti filament spacings and matrix materials have different long time field decay. A theoretical model using proximity coupling and flux creep for the observed field decay is discussed. 10 refs., 5 figs., 2 tabs

  17. Silicon calorimetry for the SSC[ Superconducting Supercollider

    International Nuclear Information System (INIS)

    Bertrand, C.; Borchi, E.; Brau, J.E.

    1989-01-01

    SSC experiments will rely heavily on their calorimeters. Silicon calorimetry, which has been introduced in recent years as a useful technology, has many attractive characteristics which may make it a viable option for consideration. The many attractive properties of silicon detectors are reviewed. The relevant present day applications of large areas of silicon detectors are summarize to illustrate the emerging use. The troublesome issue of radiation damage in a high luminosity environment like the SSC is considered with a summary of much of the recent new measurements which help clarify this situation. A discussion of the electronics and a possible mechanical configuration is presented, followed by a summary of the outstanding R and D issues. 31 refs., 11 figs., 3 tabs

  18. Reactivity feedback models for SSC-K

    Energy Technology Data Exchange (ETDEWEB)

    Han, Do Hee; Kwon, Young Min; Kim, Kyung Du; Chang, Won Pyo [Korea Atomic Energy Research Institute, Taejon (Korea)

    1998-06-01

    Safety of KALIMER is assured by the inherent safety of the core and passive safety of the safety-related systems. For the safety analysis of a new reactor design such as KALIMER, analysis models, which are consistent with the design, have to be developed for a plant-wide transient and safety analysis code. Efforts for the development of reactivity feedback models for SSC-K, which is now being developed for the safety analysis of KALIMER, is described in this report. Models for Doppler, sodium density/void, fuel axial expansion, core radial expansion, and CRDL expansion have been developed. Test runs have been performed for the unprotected accident for the verification of the models. Use of KALIMER reactivity coefficients and future development of models for GEM and PSDRS would make it possible to analyze the response of KALIMER under TOP as well as LOF and LOHS accident conditions using SSC-K. (author). 5 refs., 64 figs., 2 tabs.

  19. Compositeness and QCD at the SSC

    International Nuclear Information System (INIS)

    Barnes, V.; Blumenfeld, B.; Cahn, R.

    1987-01-01

    Compositeness may be signaled by an increase in the production of high transverse momentum hadronic jet pairs or lepton pairs. The hadronic jet signal competes with the QCD production of jets, a subject of interest in its own right. Tests of perturbative QCD at the SSC will be of special interest because the calculations are expected to be quite reliable. Studies show that compositeness up to a scale of 20 to 35 TeV would be detected in hadronic jets at the SSC. Leptonic evidence would be discovered for scales up to 10 to 20 TeV. The charge asymmetry for leptons would provide information on the nature of the compositeness interaction. Calorimetry will play a crucial role in the detection of compositeness in the hadronic jet signal. Deviations from an e/h response of 1 could mask the effect. The backgrounds for lepton pair production seem manageable. 30 refs., 19 figs., 10 tabs

  20. The SSC access shafts calculational study

    International Nuclear Information System (INIS)

    Baishev, I.S.; Mokhov, N.V.; Toohig, T.E.

    1991-06-01

    The SSC generic shaft requirements and access spacing are considered elsewhere. The shafts connecting the ground surface with the underground accelerator tunnel deliver to the surface some portion of the radiation created in the tunnel. The radiation safety problem of access shafts consists of two major questions: Does the dose equivalent at the ground surface exceed permissible limits? If it exceeds those limits, what additional shielding measures are required? A few works deal with this problem for high energy machines. This work is an attempt to answer these questions for the basic types of shafts specific to the SSC magnet delivery, utility and personnel shafts using full-scale Monte-Carlo calculations of the entire process from hadronic cascades in the lattice elements to particles scattered in the tunnel, niches, alcoves, shafts and surface bunkers and buildings. 9 refs., 16 figs., 1 tab

  1. An industrial cabling machine for the SSC

    International Nuclear Information System (INIS)

    Royet, J.; Armer, R.; Hannaford, R.; Scanlan, R.

    1989-02-01

    The SSC project will need the manufacturing of some 25,000 kilometers of keystoned flat cable. The technical specifications of the various cables to be produced are the result of five years of research and development work at LBL. An experimental cable machine was built and run in the laboratory; many improvements were implemented and tested. Semi-industrial production of the various cables was performed, and the resulting cables were used and tested in the one-meter model magnets and 17.5 meter dipole prototypes. From these experiments an industrial cabler specification was generated and used for an international RFQ. The winner of the contract is Dour Metal, a Belgium company that built the first industrial prototype which is now in a production line at New England Electric Wire Company. In this paper we describe the main characteristics of the machine and give the first industrial production results of superconducting keystoned cable for the SSC project. 4 refs

  2. New linac technology - for SSC, and beyond

    International Nuclear Information System (INIS)

    Jameson, R.A.

    1983-01-01

    With recent agreement on the high priority of seeking funding for a Superconducting Super Collider (SSC), it is appropriate to consider the injector linac requirements for such a machine. In so doing, the status of established technique and advantages of near-term R and D with relatively clear payoff are established, giving a base line for some speculation about linac possibilities even further in the future

  3. Neural networks, D0, and the SSC

    International Nuclear Information System (INIS)

    Barter, C.; Cutts, D.; Hoftun, J.S.; Partridge, R.A.; Sornborger, A.T.; Johnson, C.T.; Zeller, R.T.

    1989-01-01

    We outline several exploratory studies involving neural network simulations applied to pattern recognition in high energy physics. We describe the D0 data acquisition system and a natual means by which algorithms derived from neural networks techniques may be incorporated into recently developed hardware associated with the D0 MicroVAX farm nodes. Such applications to the event filtering needed by SSC detectors look interesting. 10 refs., 11 figs

  4. SSC collider dipole magnet end mechanical design

    International Nuclear Information System (INIS)

    Delchamps, S.W.; Bossert, R.C.; Carson, J.; Ewald, K.; Fulton, H.; Kerby, J.; Koska, W.; Strait, J.; Wake, M.; Leung, K.K.

    1991-01-01

    This paper describes the mechanical design of the ends of Superconducting Super Collider dipole magnets to be constructed and tested at Fermilab. Coil end clamps, end yoke configuration, and end plate design are discussed. Loading of the end plate by axial Lorentz forces is discussed. Relevant data from 40 mm and 50 mm aperture model dipole magnets built and tested at Fermilab are presented. In particular, the apparent influence of end clamp design on the quench behavior of model SSC dipoles is described

  5. Engineered design of SSC cooling ponds

    International Nuclear Information System (INIS)

    Bear, J.B.

    1993-05-01

    The cooling requirements of the SSC are significant and adequate cooling water systems to meet these requirements are critical to the project's successful operation. The use of adequately designed cooling ponds will provide reliable cooling for operation while also meeting environmental goals of the project to maintain streamflow and flood peaks to preconstruction levels as well as other streamflow and water quality requirements of the Texas Water Commission and the Environmental Protection Agency

  6. Computing facility at SSC for detectors

    International Nuclear Information System (INIS)

    Leibold, P.; Scipiono, B.

    1990-01-01

    A description of the RISC-based distributed computing facility for detector simulaiton being developed at the SSC Laboratory is discussed. The first phase of this facility is scheduled for completion in early 1991. Included is the status of the project, overview of the concepts used to model and define system architecture, networking capabilities for user access, plans for support of physics codes and related topics concerning the implementation of this facility

  7. The status of detectors at the SSC

    International Nuclear Information System (INIS)

    Stefanski, R.

    1990-09-01

    The announcement of the location of the SSC at the site near Waxahachie, Texas was made in January, 1989. Since then a great many important steps have been taken toward the start of the new Laboratory. Some 900 people have been brought to the site as the starting nucleus of the staff that will ultimate number about 2200. A design baseline has been completed that includes a conceptual design for the accelerator, and the detectors. Also, the process has begun to determine the configuration of detectors that will be built for the SSC. This process has several steps, and now the first of these has been taken: The detector collaborations have submitted the Expression of Interest to the Laboratory. These were reviewed by Laboratory management and the Physics Advisory Committee in July, 1990 and recommendations were made to the collaborations. Decisions were deferred for all of the detectors. But perhaps the most significant recommendation was the request to reduce the size and cost of the general purpose detectors. The detector collaborations are now reviewing their initial designs to prepare for the Letters of Intent, the next step in the detector planning process. This is clearly a difficult and crucial step in that the redesign of the detectors must be done with minimal reduction in detector quality. It is an interesting time in the development of the new laboratory, and a crucial time for the ultimate physics that will be done at the SSC

  8. Relational databases for SSC design and control

    International Nuclear Information System (INIS)

    Barr, E.; Peggs, S.; Saltmarsh, C.

    1989-01-01

    Most people agree that a database is A Good Thing, but there is much confusion in the jargon used, and in what jobs a database management system and its peripheral software can and cannot do. During the life cycle of an enormous project like the SSC, from conceptual and theoretical design, through research and development, to construction, commissioning and operation, an enormous amount of data will be generated. Some of these data, originating in the early parts of the project, will be needed during commissioning or operation, many years in the future. Two of these pressing data management needs-from the magnet research and industrialization programs and the lattice design-have prompted work on understanding and adapting commercial database practices for scientific projects. Modern relational database management systems (rDBMS's) cope naturally with a large proportion of the requirements of data structures, like the SSC database structure built for the superconduction cable supplies, uses, and properties. This application is similar to the commercial applications for which these database systems were developed. The SSC application has further requirements not immediately satisfied by the commercial systems. These derive from the diversity of the data structures to be managed, the changing emphases and uses during the project lifetime, and the large amount of scientific data processing to be expected. 4 refs., 5 figs

  9. Effect of pH on Separation of Solid Content from Paint Contained Wastewater by a Coagulant-flocculant Compound

    Directory of Open Access Journals (Sweden)

    Mojtaba Semnani Rahbar

    2014-05-01

    Full Text Available Chemical wastewater treatment is one of the attracting and common methods for wastewater treatment among the currently employed chemical unit processes. The use of coagulant-flocculant compound is one of the efficient methods for separating of paint and recovery of water. In this research, it was introduced and the effect of pH on removal of solid content from solution was studied experimentally. For this purpose, sludge and suspended solid content of the solution were determined in a jar test by measurement of UV absorption of treated solution and solid separation percentage. The results showed that in pH range 9.5-10.5, maximum efficiency of solid content removal was up to 95%. Consequently, maximum paint removal was obtained in this range of pH. The separation of solid content of the solution was due to formation of aluminum hydroxide. As shown by the results, the reduction of potassium hydroxide as pH adjuster caused decrease of pH and consequently decreases of aluminum hydroxide and solid content removal.  

  10. Solid recovered fuel: influence of waste stream composition and processing on chlorine content and fuel quality.

    Science.gov (United States)

    Velis, Costas; Wagland, Stuart; Longhurst, Phil; Robson, Bryce; Sinfield, Keith; Wise, Stephen; Pollard, Simon

    2012-02-07

    Solid recovered fuel (SRF) produced by mechanical-biological treatment (MBT) of municipal waste can replace fossil fuels, being a CO(2)-neutral, affordable, and alternative energy source. SRF application is limited by low confidence in quality. We present results for key SRF properties centered on the issue of chlorine content. A detailed investigation involved sampling, statistical analysis, reconstruction of composition, and modeling of SRF properties. The total chlorine median for a typical plant during summer operation was 0.69% w/w(d), with lower/upper 95% confidence intervals of 0.60% w/w(d) and 0.74% w/w(d) (class 3 of CEN Cl indicator). The average total chlorine can be simulated, using a reconciled SRF composition before shredding to limit for ash content marginally below the 20% w/w(d) deemed suitable for certain power plants; and a lower 95% confidence limit of net calorific value (NCV) at 14.5 MJ kg(ar)(-1). The data provide, for the first time, a high level of confidence on the effects of SRF composition on its chlorine content, illustrating interrelationships with other fuel properties. The findings presented here allow rational debate on achievable vs desirable MBT-derived SRF quality, informing the development of realistic SRF quality specifications, through modeling exercises, needed for effective thermal recovery.

  11. Biodrying process: A sustainable technology for treatment of municipal solid waste with high moisture content.

    Science.gov (United States)

    Tom, Asha P; Pawels, Renu; Haridas, Ajit

    2016-03-01

    Municipal solid waste with high moisture content is the major hindrance in the field of waste to energy conversion technologies and here comes the importance of biodrying process. Biodrying is a convective evaporation process, which utilizes the biological heat developed from the aerobic reactions of organic components. The numerous end use possibilities of the output are making the biodrying process versatile, which is possible by achieving the required moisture reduction, volume reduction and bulk density enhancement through the effective utilization of biological heat. In the present case study the detailed research and development of an innovative biodrying reactor has been carried out for the treatment of mixed municipal solid waste with high moisture content. A pilot scale biodrying reactor of capacity 565 cm(3) was designed and set up in the laboratory. The reactor dimensions consisted of an acrylic chamber of 60 cm diameter and 200 cm height, and it was enveloped by an insulation chamber. The insulation chamber was provided to minimise the heat losses through the side walls of the reactor. It simulates the actual condition in scaling up of the reactor, since in bigger scale reactors the heat losses through side walls will be negligible while comparing the volume to surface area ratio. The mixed municipal solid waste with initial moisture content of 61.25% was synthetically prepared in the laboratory and the reactor was fed with 109 kg of this substrate. Aerobic conditions were ensured inside the reactor chamber by providing the air at a constant rate of 40 litre per minute, and the direction of air flow was from the specially designed bottom air chamber to the reactor matrix top. The self heating inside reactor matrix was assumed in the range of 50-60°C during the design stage. Innovative biodrying reactor was found to be efficiently working with the temperature inside the reactor matrix rising to a peak value of 59°C by the fourth day of experiment (the

  12. SSC education: Science to capture the imagination

    International Nuclear Information System (INIS)

    Gadsden, T.; Kivlighn, S.

    1992-01-01

    To the great majority of Americans, science is merely a collection of facts and theories that should (for unknown reasons) be memorized and perhaps even understood in order for one to function as a responsible citizen. Few see science as a way of thinking and questioning and as an approach to learning the secrets of our world. In addition, most children and many adults have a stereotypical view of scientists as studious men in lab coats who spend all their time working alone in dark and smelly chemical or biological laboratories. The Superconducting Super Collider (SSC) totally contradicts such a perception. This great instrument is being created by thousands of scientists, engineers, business people, technicians, administrators, and others, from dozens of nations, working together to realize a shared vision to seek answers to shared questions. The SSCL also provides an opportunity to change the mistaken impressions about science and scientists that have resulted in fewer students pursuing careers in fields related to science. In addition, it will serve as a catalyst to help people understand the roles that scientific thought and inquiry can play in bettering their lives and the lives of their offspring. Recognizing this problem in our society, the creators of the SSC Laboratory made a commitment to use the SSC to improve science education. Consequently, in addition to building the world's premier high-energy physics laboratory, the SSCL has a second goal: creation of a major national and international educational resource. To achieve the latter goal, the Education Office of the SSCL is charged with using the resources of the Laboratory, both during construction and during operation, to improve education in science and mathematics at all levels (prekindergarten through post-doctorate) and for all components of our society (including the general public), in the United States and around the world

  13. SSC lattice database and graphical interface

    International Nuclear Information System (INIS)

    Trahern, C.G.; Zhou, J.

    1991-11-01

    When completed the Superconducting Super Collider will be the world's largest accelerator complex. In order to build this system on schedule, the use of database technologies will be essential. In this paper we discuss one of the database efforts underway at the SSC, the lattice database. The SSC lattice database provides a centralized source for the design of each major component of the accelerator complex. This includes the two collider rings, the High Energy Booster, Medium Energy Booster, Low Energy Booster, and the LINAC as well as transfer and test beam lines. These designs have been created using a menagerie of programs such as SYNCH, DIMAD, MAD, TRANSPORT, MAGIC, TRACE3D AND TEAPOT. However, once a design has been completed, it is entered into a uniform database schema in the database system. In this paper we discuss the reasons for creating the lattice database and its implementation via the commercial database system SYBASE. Each lattice in the lattice database is composed of a set of tables whose data structure can describe any of the SSC accelerator lattices. In order to allow the user community access to the databases, a programmatic interface known as dbsf (for database to several formats) has been written. Dbsf creates ascii input files appropriate to the above mentioned accelerator design programs. In addition it has a binary dataset output using the Self Describing Standard data discipline provided with the Integrated Scientific Tool Kit software tools. Finally we discuss the graphical interfaces to the lattice database. The primary interface, known as OZ, is a simulation environment as well as a database browser

  14. SSC collider dipole magnet end mechanical design

    International Nuclear Information System (INIS)

    Delchamps, S.W.; Bossert, R.C.; Carson, J.; Ewald, K.; Fulton, H.; Kerby, J.; Koska, W.; Strait, J.; Wake, S.M.; Leung, K.K.

    1991-05-01

    This paper describes the mechanical design of the ends of Superconducting Super Collider dipole magnets to be constructed and tested at Fermilab. Coil end clamps, end yoke configuration, and end plate design are discussed. Loading of the end plate by axial Lorentz forces is discussed. Relevant data from 40 mm and 50 mm aperture model dipole magnets built and tested at Fermilab are presented. In particular, the apparent influence of end clamp design on the quench behavior of model SSC dipoles is described. 8 refs., 3 figs

  15. Report of the Ad Hoc Committee on SSC physics

    International Nuclear Information System (INIS)

    1990-04-01

    The Ad Hoc Committee on SSC Physics has reexamined the relationship between beam energy, machine luminosity, and physics capability. In the next section, the physics motivation for the SSC is reviewed in general terms. This is followed by a discussion of the ability to detect a number of specific processes as a function of the SSC energy and luminosity. The viability of various detector technologies is then assessed as a function of luminosity. The report ends with a brief summary and some conclusions

  16. Parameter selection for the SSC trade-offs and optimization

    International Nuclear Information System (INIS)

    Edwards, D.A.; Syphers, M.J.

    1991-01-01

    In November of 1988, a site was selected in the state of Texas for the SSC. In January of 1989, the SSC Laboratory was established in Texas to adapt the design of the collider to the site and to manage the construction of the project. This paper describes the evolution of the SSC design since site selection, notes the increased concentration on the injector system, and addresses the rationale for choice of parameters

  17. Measurements of ground motion and SSC dipole vibrations

    International Nuclear Information System (INIS)

    Parkhomchuk, V.V.; Shiltsev, V.D.; Weaver, H.J.

    1993-06-01

    The results of seismic ground measurements at the Superconducting Super Collider (SSC) site and investigations of vibrational properties of superconducting dipoles for the SSC are presented. Spectral analysis of the data obtained in the large frequency band from 0.05 Hz to 2000 Hz is done. Resonant behavior and the dipole-to-ground transform ratio are investigated. The influence of measured vibrations on SSC operations is considered

  18. Uses of the chiral Lagrangian at the SSC

    International Nuclear Information System (INIS)

    Dawson, S.

    1992-09-01

    In the event that the SSC does not observe any resonances such as a Higgs boson or a techni-rho meson, we would like to know if the SSC can still discover something about the nature of the electroweak symmetry breaking. In particular, we consider the question of whether there is a ''no-lose'' corollary at the SSC. We will use chiral Lagrangian techniques to address this question and analyze their utility for studying events containing W and Z gauge bosons at the SSC

  19. Full length prototype SSC dipole test results

    International Nuclear Information System (INIS)

    Strait, J.; Brown, B.C.; Carson, J.

    1987-01-01

    Results are presented from tests of the first full length prototype SSC dipole magnet. The cryogenic behavior of the magnet during a slow cooldown to 4.5K and a slow warmup to room temperature has been measured. Magnetic field quality was measured at currents up to 2000 A. Averaged over the body field all harmonics with the exception of b 2 and b 8 are at or within the tolerances specified by the SSC Central Design Group. (The values of b 2 and b 8 result from known design and construction defects which will be be corrected in later magnets.) Using an NMR probe the average body field strength is measured to be 10.283 G/A with point to point variations on the order of one part in 1000. Data are presented on quench behavior of the magnet up to 3500 A (approximately 55% of full field) including longitudinal and transverse velocities for the first 250 msec of the quench

  20. Preserving SSC Design Function Using RCM Principles

    International Nuclear Information System (INIS)

    Mohammadi, K.

    2009-01-01

    Reliability-Centered Maintenance (RCM) can be defined as an approach that employs preventive, predictive, proactive, and reactive maintenance practices and strategies in an integrated manner to increase the probability that a Structure, System, or Component (SSC) will function as designed over its life cycle with optimum maintenance. The goal of RCM is to preserve the SSC intended design function at the lowest cost by developing a maintenance strategy that is supported by sound technical and economic justification. RCM has been used extensively by the aircraft, space, defense, power generation, and manufacturing industries where functional failures of SSCs can have the potential to compromise worker or public safety, cause adverse environmental impact, cause loss of production, and/or result in excessive damage to critical SSCs. This paper provides a framework for performing an RCM analysis in support of DOE Order 430.1A (Life Cycle Asset Management) and DOE Order 420.1B (Facility Safety). The influence of RCM on the various aspects of the maintenance program including the work control process is also discussed

  1. An alternate end design for SSC dipoles

    International Nuclear Information System (INIS)

    Peters, C.; Caspi, S.; Taylor, C.

    1989-02-01

    Experience in the SSC dipole program has shown that fabrication of cylindrical coil ends is difficult. Cable stiffness requires large forces to maintain the proper position of the conductors in the end during winding. After winding, the coil ends remain distorted nd significant motion of the need conductors is required to force the coil end into the molding cavity. Local mechanical stresses are high during this process and extra pieces of insulation are required to prevent turn-to-turn shorts from developing during the winding and molding steps. Prior to assembly the coil end is compressed in a mold cavity and injected with a filler material to correct surface irregularities and fill voids in the end. LBL has developed an alternate design which permits the conductors to be wound over the end using minimal force and technician coerosion. The conductors are placed on a conical surface where the largest diameter over the outer layer conductors is 10 cm. No coil end spaces or insulation pieces between turns are required. The conductor geometry was analytically optimized to meet SSC multipole requirements for the ends. The first 1-m dipole utilizing this end geometry has been constructed and successfully tested. Design and construction data are presented. Also model test results, including training and multipole measurements of the end are given. 1 ref., 12 figs., 3 tabs

  2. Adsorption of Lead Content in Leachate of Sukawinatan Landfill Using Solid Waste of Tofu

    Directory of Open Access Journals (Sweden)

    Sri Hartati

    2016-08-01

    Full Text Available A study on the adsorption of lead content in the leachate from the landfill by using solid waste of tofu. This study assed the effects of weight of the solid waste of tofu and the contact time on the efficiency of the Pb adsorption. The sample used in this study was artificial sample of a solution of Pb metal ion and the sample of the leachate of the landfill waste. The study was carried out with a batch system, with the variables of weight of waste of tofu of 0.5; 1.0; 1.5 g. While the variables of the contact time were 0, 30, 60, 90, 120 and 150 minutes. To determine the optimum conditions, the waste of tofu was dissolved in 50 mL of Pb metal ion solution with a concentration of 20.27 mg/L and stirred with a shaker for 30 minutes at a speed of 180 rpm. The same thing was done by varying the contact time. When the optimum condition was obtained, it was applied with varying concentrations of Pb metal ion solution and garbage landfill leachate. The initial and the final levels of the Pb metal ion solution were analyzed by using the Atomic Adsorption Spectroscopy (AAS. The initial and the final results of the heavy metals were analyzed for disclosing the adsorption efficiency. To reveal the effects of the weight of the waste of tofu and the contact time, the data were analyzed with graphs. The waste of tofu with a weight of 1.5 g and a contact time of 90 minutes, had an adsorption efficiency of 97.68% at a concentration of 20.27 mg / L for Pb ion solution and 28.57% for the leachate from the landfill waste in 100 mL of leachate.

  3. Characterisation of chemical composition and energy content of green waste and municipal solid waste from Greater Brisbane, Australia.

    Science.gov (United States)

    Hla, San Shwe; Roberts, Daniel

    2015-07-01

    The development and deployment of thermochemical waste-to-energy systems requires an understanding of the fundamental characteristics of waste streams. Despite Australia's growing interest in gasification of waste streams, no data are available on their thermochemical properties. This work presents, for the first time, a characterisation of green waste and municipal solid waste in terms of chemistry and energy content. The study took place in Brisbane, the capital city of Queensland. The municipal solid waste was hand-sorted and classified into ten groups, including non-combustibles. The chemical properties of the combustible portion of municipal solid waste were measured directly and compared with calculations made based on their weight ratios in the overall municipal solid waste. The results obtained from both methods were in good agreement. The moisture content of green waste ranged from 29% to 46%. This variability - and the tendency for soil material to contaminate the samples - was the main contributor to the variation of samples' energy content, which ranged between 7.8 and 10.7MJ/kg. The total moisture content of food wastes and garden wastes was as high as 70% and 60%, respectively, while the total moisture content of non-packaging plastics was as low as 2.2%. The overall energy content (lower heating value on a wet basis, LHVwb) of the municipal solid waste was 7.9MJ/kg, which is well above the World Bank-recommended value for utilisation in thermochemical conversion processes. Copyright © 2015 Elsevier Ltd. All rights reserved.

  4. Polonium content in sediments and other solid tailings generated by mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Chmielewska, Izabela; Michalik, Boguslaw [Silesian Centre for Environmental Radioactivity, Central Mining Institute, 40-166 Katowice, Pl. Gwarkow 1 (Poland)

    2014-07-01

    All legal limits or recommendations concerning NORM include only primordial radionuclides and secular equilibrium state among all decay products is assumed. This is not valid for a majority of residues from NORM industry where activity concentration of progenies can substantially differ each other. Upper Silesia Coal Basin is a unique region where mining activity is continuously done over longer period of time and this include discharging of radium-bearing water to environment and creating huge amount of solid wastes where at the beginning radium is the most dominant radionuclide. With time other daughter products start to build up and actual exposure to radiation is changing. One of them is polonium that with regard to its chemical properties can be easily accumulated in non-human biota resulting in the increase of radiation exposure. In our work we focused attention on sediments where content of {sup 210}Po was determined by chemical separation followed by alpha spectrometry. Chemical preparation involves organic matter destruction and dissolution of the sample itself (if possible). In our research we employed wet digestion by means of mixture of concentrated acids: HNO{sub 3}, HClO{sub 4}, HCl. Later on polonium was spontaneously deposited onto silver disc and measured with use of alpha spectrometry. In this article we want to show results of our study and as well to present some conclusions concerning changes in radiation risk assessment when actual concentration of polonium is taken into consideration. (authors)

  5. Changes on the Solid Fat Content of Palm Oil/ Sunflower Oil Blends via Inter esterification

    International Nuclear Information System (INIS)

    Suria Ramli; Azwani Mohd Lazim; Siti Aishah Hasbullah

    2013-01-01

    Physicochemical characteristics of binary blends containing refined-deodorized-bleached palm oil (RBDPO) and sunflower oil (SFO) were studied before and after chemical inter esterification at different temperature (110 degree Celsius (CIE1) and 80 degree Celsius (CIE2)) using sodium methoxide as catalyst. Thirty-three samples with different ratios were analyzed for triacylglycerol (TAG) composition, fatty acid composition (FAC) and solid fat content (SFC) profile. Upon CIE, extensive rearrangements of fatty acids among triacylglycerol (TAG) were seen. Generally, CIE not induced enormous changes in the TAG compositions of ratio 8:2 and 5:5 of RBDPO:SFO blends. However, CIE induced enormous changes in the TAG compositions of the 9:1, 7:3, 6:4, 4:6, 3:7, 2:8 and 1:9 blends, which some of the TAGs were increasing while the other decreasing. These changes in TAG profiles resulted in some changes in the physical properties (especially SFC) of the blends. Generally, the SFC of inter esterified blend were decreased after CIE1 and increased after CIE2, except for sample 10:0, 8:2, 7:3, 5:5 and 9:1 which were decreased after CIE1 and CIE2. As a conclusion, CIE1 and CIE2 successfully changed the physicochemical characteristics of the binary blends. (author)

  6. Ethanol production from food waste at high solids content with vacuum recovery technology.

    Science.gov (United States)

    Huang, Haibo; Qureshi, Nasib; Chen, Ming-Hsu; Liu, Wei; Singh, Vijay

    2015-03-18

    Ethanol production from food wastes does not only solve environmental issues but also provides renewable biofuels. This study investigated the feasibility of producing ethanol from food wastes at high solids content (35%, w/w). A vacuum recovery system was developed and applied to remove ethanol from fermentation broth to reduce yeast ethanol inhibition. A high concentration of ethanol (144 g/L) was produced by the conventional fermentation of food waste without a vacuum recovery system. When the vacuum recovery is applied to the fermentation process, the ethanol concentration in the fermentation broth was controlled below 100 g/L, thus reducing yeast ethanol inhibition. At the end of the conventional fermentation, the residual glucose in the fermentation broth was 5.7 g/L, indicating incomplete utilization of glucose, while the vacuum fermentation allowed for complete utilization of glucose. The ethanol yield for the vacuum fermentation was found to be 358 g/kg of food waste (dry basis), higher than that for the conventional fermentation at 327 g/kg of food waste (dry basis).

  7. Design and operation of a passive neutron monitor for assaying the TRU content of solid wastes

    International Nuclear Information System (INIS)

    Brodzinski, R.L.; Brown, D.P.; Rieck, H.G. Jr.; Rogers, L.A.

    1984-02-01

    A passive neutron monitor has been designed and built for determining the residual transuranic (TRU) and plutonium content of chopped leached fuel hulls and other solid wastes from spent Fast Flux Test Facility (FFTF) fuel. The system was designed to measure as little as 8 g of plutonium or 88 mg of TRU in a waste package as large as a 208-l drum which could be emitting up to 220,000 R/hr of gamma radiation. For practical purposes, maximum assay times were chosen to be 10,000 sec. The monitor consists of 96 10 BF 3 neutron sensitive proportional counting tubes each 5.08 cm in diameter and 183 cm in active length. Tables of neutron emission rates from both spontaneous fission and (α,n) reactions on oxygen are given for all contributing isotopes expected to be present in spent FFTF fuel. Tables of neutron yeilds from isotopic compositions predicted for various exposures and cooling times are also given. Methods of data reduction and sources, magnitude, and control of errors are discussed. Backgrounds and efficiencies have been measured and are reported. A section describing step-by-step operational procedures is included. Guidelines and procedures for quality control and troubleshooting are also given. 13 references, 15 figures, 4 tables

  8. STUDIES ON HIGH SOLID CONTENT AND STABLE EMULSIFIER—FREE EMULSION POLYMERIZATION

    Institute of Scientific and Technical Information of China (English)

    TangGuangliang; HaoGuangjie; 等

    1998-01-01

    In this article,AHPS(3-allyloxy-2-hydroxy-1-propanesulfonate salt) was synthesized to use in emulsifier-free emulsion polymerization of BA/BMA/MMA system for high solid content latexes.Storage stability,flow behavior of the latexes,morphology of the obtained latex particles,dynamic viscoelastic behavior,tensile strength and water resistance properties of the resulted copolymers were investigated.The experimental results show that with the addition of AHPS,stability of the emulsion is greatly improved that there appears no apparent precipitation during the polymerization and storage at room temperature for 6 months and at -10℃ for four months.Flow of the latexes follows the Bingham body laws,diameter of the latex particles is about 0.6μm,of which is larger than that of by conventional emulsion polymerization(0.12μm).In addition,not only water resistance of the copolymers obtained by emulsifier-free emulstion polymerization is greatly improved,but also tensile strength is obviously enhanced.

  9. Dicty_cDB: SSC534 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available SS (Link to library) SSC534 (Link to dictyBase) - - - Contig-U13922-1 SSC534Z (Link... to Original site) - - SSC534Z 711 - - - - Show SSC534 Library SS (Link to library) Clone ID SSC534 (Link to dic... 1.3 FM992688_1247( FM992688 |pid:none) Candida dubliniensis CD36 chrom... 35 3.0 EU565733_1( EU565733 |pid:none) Unculture... 20.0 %: nuclear 16.0 %: vesicles of secretory system 12.0 %: mitochondrial 8.0 %: Golgi 8.0 %: endoplasmic reticul...kholderia multivorans ATCC 1... 33 6.6 AM260479_1383( AM260479 |pid:none) Ralstonia e

  10. Dicty_cDB: SSC538 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available SS (Link to library) SSC538 (Link to dictyBase) - - - Contig-U13922-1 SSC538Z (Link... to Original site) - - SSC538Z 712 - - - - Show SSC538 Library SS (Link to library) Clone ID SSC538 (Link to dic...SHR34... 36 1.3 FM992688_1247( FM992688 |pid:none) Candida dubliniensis CD36 chrom... 35 3.0 EU565733_1( EU565733 |pid:none) Uncultur...9385_2728( AP009385 |pid:none) Burkholderia multivorans ATCC 1... 33 6.6 AM260479_1383( AM260479 |pid:none) ... reticulum 4.0 %: extracellular, including cell wall 4.0 %: cytoskeletal 4.0 %: vacu

  11. SSC [Superconducting Super Collider] magnet technology

    International Nuclear Information System (INIS)

    Taylor, C.

    1987-09-01

    To minimize cost of the SSC facility, small-bore high field dipole magnets have been developed;some of the new technology that has been developed at several U.S. national laboratories and in industry is summarized. Superconducting wire with high J/sub c/ and filaments as small as 5μm diameter is not produced iwht mechanical properties suitable for reliable cable production. A variety of collar designs of both aluminum and stainless steel have been used in model magnets. A low-heat leak post-type cryostat support system is used and a system for accurate alignment of coil-collar-yoke in the cryostat has been developed. Model magnets of 1-m, 1.8 m, 4.5 m, and 17 m lengths have been build during the past two years. 23 refs., 5 figs., 2 tabs

  12. SSC physics signatures and trigger requirements

    International Nuclear Information System (INIS)

    1985-01-01

    Strategies are considered for triggering on new physics processes on the environment of the SSC, where interaction rates will be very high and most new physics processes quite rare. The quantities available for use in the trigger at various levels are related to the signatures of possible new physics. Two examples were investigated in some detail using the ISAJET Monte Carlo program: Higgs decays to W pairs and a missing energy trigger applied to gluino pair production. In both of the examples studied in detail, it was found that workable strategies for reducing the trigger rate were obtainable which also produced acceptable efficiency for the processes of interest. In future work, it will be necessary to carry out such a program for the full spectrum of suggested new physics

  13. SSC [Superconducting Super Collider] magnet mechanical interconnections

    International Nuclear Information System (INIS)

    Bossert, R.C.; Niemann, R.C.; Carson, J.A.; Ramstein, W.L.; Reynolds, M.P.; Engler, N.H.

    1989-03-01

    Installation of superconducting accelerator dipole and quadrupole magnets and spool pieces in the SSC tunnel requires the interconnection of the cryostats. The connections are both of an electrical and mechanical nature. The details of the mechanical connections are presented. The connections include piping, thermal shields and insulation. There are seven piping systems to be connected. These systems must carry cryogenic fluids at various pressures or maintain vacuum and must be consistently leak tight. The interconnection region must be able to expand and contract as magnets change in length while cooling and warming. The heat leak characteristics of the interconnection region must be comparable to that of the body of the magnet. Rapid assembly and disassembly is required. The magnet cryostat development program is discussed. Results of quality control testing are reported. Results of making full scale interconnections under magnet test situations are reviewed. 11 figs., 4 tabs

  14. Integrated design of the SSC linac injector

    International Nuclear Information System (INIS)

    Evans, D.; Valiecnti, R.; Wood, F.

    1992-01-01

    The Ion Source, Low Energy Beam Transport (LEBT), and Radio Frequency Quadrupole (RFQ) of the Superconducting Super Collider (SSC) Linac act as a unit (referred to as the Linac Injector), the Ion Source and LEBT being cantilevered off of the RFQ. Immediately adjacent to both ends of the RFQ cavity proper are endwall chambers containing beam instrumentation and independently-operated vacuum isolation valves. The Linac Injector delivers 30 mA of H - beam at 2.5 MeV. This paper describes the design constraints imposed on the endwalls, aspects of the integration of the Ion Source and LEBT including attachment to the RFQ, maintainability and interchangeability of LEBTs, vacuum systems for each component, and the design of necessary support structure. (Author) 2 tab

  15. Closed orbit correction in the SSC

    International Nuclear Information System (INIS)

    Bourianoff, G.; Cole, B.; Ferede, H.; Pilat, F.

    1991-01-01

    Most of the techniques associated with closed orbit correction are widely known. The present paper gives a brief description of one such method and discusses the results obtained when it is applied to the SSC collider lattice. The emphasis is on features of the lattice which effect closed orbit correction and it is likely that any of the 8 methods cataloged in a cited reference would yield similar results. The global scheme described here is very robust and easy to apply. The results of three separate studies are briefly described. Typical results for the residual RMS closed orbit in the arc is calculated to be 0.65 mm with peak values of 3 mm

  16. GIS/FIS development for the SSC

    International Nuclear Information System (INIS)

    Oslin, A.; Butalla, M.

    1992-01-01

    Facility management for a project of the size and complexity of the SSCL is a challenging task. The Facility Information System/Geographic Information System (FIS/GIS) should provide an effective tool for the demanding work ahead. Both the FIS and GIS encompass information that many potential users across multiple disciplines will require for effective facility management. FIS will be integrated with the GIS for applications that involve duplicate needs of graphic and attribute data. In particular, infrastructure networks, environmental monitoring, emergency dispatching, and hazardous materials management have been identified as areas where the two systems will interface. In general, the GIS will manage graphic and attribute information outside the actual structure of the SSCL. The FIS will take over operation of components and networks within the SSCL facility. By providing a method for informed decision-making, implementation of the SSC FIS/GIS will facilitate the tasks involved in managing our Laboratory during all phases of its life

  17. The SSC full cell prototype string test

    International Nuclear Information System (INIS)

    Kraushaar, P.; Burgett, W.; Cromer, L.

    1994-11-01

    At the conclusion of the SSC half cell magnet string testing program. In February, 1993, the preliminary data analysis revealed that several substantive technical questions remained unresolved. These questions were: (1) could the high voltages to ground (>2 kV) measured during fault (quench) conditions be substantially reduced, (2) could the number of magnetic elements that became resistive (quenched) be controlled and (3) did the cryostats of the magnetic elements provide adequate insulation and isolation to meet designed refrigeration loads. To address these and other existing question a prototypical full cell of collider magnets (ten dipoles and two quadrupoles) was assembled and tested. At the conclusion of this testing there were definitive answers to most of the questions with numerical substantiation, the notable exception being the beat leak question. These answers and other results and issues are presented in this paper

  18. Physics requirements for LHC/SSC calorimetry

    International Nuclear Information System (INIS)

    Green, D.

    1991-10-01

    The goal of the next generation of collider detectors is to study the origin of electroweak symmetry breaking. The mass scale for this study is roughly 1 TeV. No matter what the details of the mechanism, one can be confident that new phenomena will occur, since weak interactions become strong, i.e., violate partial wave unitarity, at that mass scale. The partial wave amplitude for ee→ WW scattering is; ao∼4φ/α w (M w /M) 2 , ao∼1 if M ∼1 TeV. Therefore, the detectors for LHC/SSC must be able to confront this mass scale. In particular, the electroweak dynamics is such that the study of gauge boson pairs has a high priority. Given that the simplest decay modes for gauge boson are into leptons, the new detectors will naturally tend to optimize performance for leptons

  19. Requirements for SSC central computing staffing (conceptual)

    International Nuclear Information System (INIS)

    Pfister, J.

    1985-01-01

    Given a computation center with --10,000 MIPS supporting --1,000 users, what are the staffing requirements? The attempt in this paper is to list the functions and staff size required in a central computing or centrally supported computing complex. The organization assumes that although considerable computing power would exist (mostly for online) in the four interaction regions (IR) that there are functions/capabilities better performed outside the IR and in this model at a ''central computing facility.'' What follows is one staffing approach, not necessarily optimal, with certain assumptions about numbers of computer systems, media, networks and system controls, that is, one would get the best technology available. Thus, it is speculation about what the technology may bring and what it takes to operate it. From an end user support standpoint it is less clear, given the geography of an SSC, where and what the consulting support should look like and its location

  20. Single bunch instabilities in an SSC

    International Nuclear Information System (INIS)

    Ruth, R.D.

    1984-01-01

    In this note coherent instability thresholds are estimated for the SSC and discuss some of the subsequent design restrictions. The various instabilities are set out in a block diagram with the essential features of each. The assumption is made that long wavelength coupled bunch effects can be cured effectively by a feedback system (both longitudinal and transverse) and that the impedance of the feedback system is such as to cancel that of the environment (at low frequency). Alternatively, the long wake field is assumed to be exactly canceled, on the average, by a feedback wake field. This leaves only single bunch effects. Thresholds for fast-blowup are discussed both in the longitudinal and transverse and the transverse mode coupling instability more familiar in electron/positron storage rings is covered. The impedances considered are a broadband impedance and the resistive wall impedance

  1. 84 K nitrogen system for the SSC

    International Nuclear Information System (INIS)

    McAshan, M.; Thirumaleshwar, M.; Abramovich, S.; Ganni, V.; Scheidemantle, A.

    1992-01-01

    The nitrogen system for the Superconducting Super Collider (SSC) is designed to provide the 84 K (nominal) shield refrigeration for the collider rings. Liquid nitrogen is supplied to the collider tunnel from one, two, or more locations on the surface through the service shafts and is distributed along, the 87 km of both rings by the 84 K shield lines. Additional design requirements for the nitrogen distribution system include precooling, fluid supply to the helium plants, supplying makeup liquid nitrogen to the reservoirs located at the entrance of the main shafts, and providing an efficient cooldown means for the cold mass from 300 K to 90 K. The operational modes and possible emergency and maintenance conditions of the collider are taken into account for the nitrogen system design. The status of our work, including design considerations that address thermal aspects (heat load, recooling scheme, etc.) and hydraulic aspects (pressures, elevations, distances, etc.) of the nitrogen system will be discussed

  2. The SSC full cell prototype string test

    International Nuclear Information System (INIS)

    McInturff, A.D.; Kraushaar, P.; Burgett, W.; Cromer, L.

    1994-01-01

    At the conclusion of the SSC half cell magnet string testing program in February, 1993, the preliminary data analysis revealed that several substantive technical questions remained unresolved. These questions were: (1) could the high voltages to ground (>2 kV) measured during fault (quench) conditions be substantially reduced, (2) could the number of magnetic elements that became resistive (quenched) be controlled and 3) did the cryostats of the magnetic elements provide adequate insulation and isolation to meet designed refrigeration loads. To address these and other existing questions, a prototypical fall cell of collider magnets (ten dipoles and two quadrupoles) was assembled and tested. At the conclusion of this testing there were definitive answers to most of the questions with numerical substantiation, the notable exception being the beat leak question. These answers and other results and issues are presented in this paper

  3. Ac loss measurement of SSC dipole magnets

    International Nuclear Information System (INIS)

    Delchamps, S.; Hanft, R.; Jaffery, T.; Kinney, W.; Koska, W.; Lamm, M.J.; Mazur, P.O.; Orris, D.; Ozelis, J.P.; Strait, J.; Wake, M.

    1992-09-01

    AC losses in full length and 1.5 m model SSC collider dipoles were successfully measured by the direct observation of energy flow into and out of magnets during a ramp cycle. The measurement was performed by using two double-integrating type digital volt meters (DVM's) for current and voltage measurement. Measurements were performed for six is m long ASST magnets and five 1.5 m long model magnets, inducting one 40 mm diameter magnet. There were large variations in the eddy current losses. Since these magnets use conductors with slight deviations in their internal structures and processing of the copper surface depending on the manufacturer, it is likely that there are differences in the contact resistance between strands. Correlation between the ramp rate dependence of the,quench current and the eddy current loss was evident

  4. Radiation levels in the SSC interaction regions

    Energy Technology Data Exchange (ETDEWEB)

    Groom, D.E. [ed.

    1988-06-10

    The radiation environment in a typical SSC detector has been evaluated using the best available particle production models coupled with Monte Carlo simulations of hadronic and electromagnetic cascades. The problems studied include direct charged particle dose, dose inside a calorimeter from the cascades produced by incident photons and hadrons, the flux of neutrons and photons backscattered from the calorimeter into a central cavity, and neutron flux in the calorimeter. The luminosity lifetime at the SSC is dominated by collision losses in the interaction regions, where the luminosity is equivalent to losing an entire full-energy proton beam into the apparatus every six days. The result of an average p-p collision can be described quite simply. The mean charged multiplicity is about 110, and the particles are distributed nearly uniformly in pseudorapidity ({eta}) over all the angles of interest. The transverse momentum distribution is independent of angle, and for our purposes may be written as p{perpendicular}exp(-p{perpendicular}/{beta}). The mean value of p{perpendicular} may be as high as 0.6 GeV/c. Most of the radiation is produced by the very abundant low-p{perpendicular} particles. The dose or neutron fluence produced by individual particles in this energy region are simulated over a wide variety of conditions, and several measurements serve to confirm the simulation results. In general, the response (a dose, fluence, the number of backscattered neutrons, etc.) for an incident particle of momentum p can be parameterized in the form Np{sup {alpha}}, where 0.5 < {alpha}< 1.0. The authors believe most of their results to be accurate to within a factor of two or three, sufficiently precise to serve as the basis for detailed designs.

  5. Effect of total solids content on biohydrogen production and lactic acid accumulation during dark fermentation of organic waste biomass.

    Science.gov (United States)

    Ghimire, Anish; Trably, Eric; Frunzo, Luigi; Pirozzi, Francesco; Lens, Piet N L; Esposito, Giovanni; Cazier, Elisabeth A; Escudié, Renaud

    2018-01-01

    Production of biohydrogen and related metabolic by-products was investigated in Solid State Dark Fermentation (SSDF) of food waste (FW) and wheat straw (WS). The effect of the total solids (TS) content and H 2 partial pressure (pp H2 ), two of the main operating factors of SSDF, were investigated. Batch tests with FW at 10, 15, 20, 25 and 30% TS showed considerable effects of the TS on metabolites distribution. H 2 production was strongly inhibited for TS contents higher than 15% with a concomitant accumulation of lactic acid and a decrease in substrate conversion. Varying the pp H2 had no significant effect on the conversion products and overall degradation of FW and WS, suggesting that pp H2 was not the main limiting factor in SSDF. This study showed that the conversion of complex substrates by SSDF depends on the substrate type and is limited by the TS content. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Variance component analysis of quantitative trait loci for pork carcass composition and meat quality on SSC4 and SSC11

    NARCIS (Netherlands)

    Wijk, van H.J.; Dibbits, B.W.; Liefers, S.C.; Buschbell, H.; Harlizius, B.; Heuven, H.C.M.; Knol, E.F.; Bovenhuis, H.; Groenen, M.A.M.

    2007-01-01

    In a previous study, QTL for carcass composition and meat quality were identified in a commercial finisher cross. The main objective of the current study was to confirm and fine map the QTL on SSC4 and SSC11 by genotyping an increased number of individuals and markers and to analyze the data using a

  7. Process control of solid-state fermentation : simultaneous control of temperature and moisture content

    NARCIS (Netherlands)

    Nagel, F.J.I.

    2002-01-01

    Solid-state fermentation (SSF), i.e. cultivation of micro-organisms on moist solid substrates in the absence of free-flowing water, is an alternative for submerged fermentation (SmF) for the production of biotechnological products. In recent years, research on SSF has led to a

  8. Personal extrapolation of CDF test beam use to the SSC

    International Nuclear Information System (INIS)

    Nodulman, L.

    1986-01-01

    The author's personal experience in test beam usage at CDF is used to predict SSC needs at the point of turn-on. It is concluded that the test beam demand will reflect the scale of effort involved in SSC detectors rather than the total number of them. Provision for later expansion is recommended. It is also recommended that the test beam facilities, as well as detector electronics, should reflect the available dynamic range; particularly, a single high energy beam derived from the SSC could be shared by several groups

  9. Geotechnical characterization and construction methods for SSC tunnel excavation

    International Nuclear Information System (INIS)

    Nelson, P.P.; Lundin, T.K.

    1990-06-01

    The site for the Superconducting Super Collider (SSC) facility was selected in 1988 after a nationwide proposal competition. The selected site is located in Ellis County, Texas, surrounding the town of Waxahachie which is about 30 miles (48 km) south of the City of Dallas central business district. This paper will describe the geotechnical conditions anticipated for excavation at the SSC site. A general geologic and geomechanical description of the rock present will be followed by a summary of the site-specific conceptual design for the tunneled components of the SSC machine. The Supercollider project will include about 70 miles (113) km of tunnel excavation

  10. Personal extrapolation of CDF test beam use to the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Nodulman, L.

    1986-06-23

    The author's personal experience in test beam usage at CDF is used to predict SSC needs at the point of turn-on. It is concluded that the test beam demand will reflect the scale of effort involved in SSC detectors rather than the total number of them. Provision for later expansion is recommended. It is also recommended that the test beam facilities, as well as detector electronics, should reflect the available dynamic range; particularly, a single high energy beam derived from the SSC could be shared by several groups. (LEW)

  11. Recent developments in wire chamber tracking at SSC

    International Nuclear Information System (INIS)

    Ogren, H.

    1990-01-01

    All of the major SSC proposed detectors use wire chambers in their tracking systems. The feasibility of wire chambers in an SSC detector has now been established by a number of groups planning detectors at SSC. The major advances during the past year in understanding straw tube drift chambers are presented and several innovations in gaseous wire chambers are discussed. The R and D section will concentrate on progress in drift cell design, electronics and signal processing, and engineering aspects of the tracking designs

  12. Co-digestion of ruminal content and blood from slaughterhouse industries: influence of solid concentration and ammonium generation.

    Science.gov (United States)

    López, I; Passeggi, M; Borzacconi, L

    2006-01-01

    At the present time, organic solid wastes from industries and agricultural activities are considered to be promising substrates for biogas production via anaerobic digestion. Moreover solids stabilisation is required before reutilization or disposal. Slaughterhouses are among the most important industries in Uruguay and produce 150,000 tons of ruminal content (RC) and 30,000 tons of blood per year. In order to determine the influence of the solids and blood contents, the ammonia inhibition and the inoculum adaptation co-digestion batch tests were performed. A set of experiences with TS concentration of 2.5%, 5% and 7.5% and different ratios of RC/blood were carried out using an inoculum from an UASB reactor. In all experiences fast blood hydrolisation was observed. A higher methane production was detected in the experiences with higher TS content. However, the fraction of solids degradation was lower in these experiences. A plateau in the biogas production was found. The free ammonia level, which was above the reported inhibitory levels, could explain this behaviour. After the inhibition period the biogas production restarted probably due to the biomass acclimatisation to the ammonia. In order to determine the inoculum adaptation a new experiment was performed. The inoculum used was the sludge coming from the first set of experiences. Based upon batch tests a 3.5 m3 pilot reactor was designed and started up. Ammonia inhibition was avoided by the start-up strategy and in two weeks the biogas production was 3.5 m3/d. The VS stabilisation with a solid retention time of 20 days was of 43%. The pilot reactor working at steady state had a TS concentration of 3-4% with a ratio of RC/blood of 10:1 at the entrance.

  13. Cabling for an SSC silicon tracking system

    International Nuclear Information System (INIS)

    Ziock, H.; Boissevain, J.; Cooke, B.; Miller, W.

    1990-01-01

    As part of the Superconducting Super Collider Laboratory (SSCL) funded silicon tracking subsystem R ampersand D program, we examine the problems associated with cabling such a system. Different options for the cabling plant are discussed. A silicon microstrip tracking detector for an SSC experiment is an extremely complex system. The system consists of approximately 10 7 detector channels, each of which requires a communication link with the outside world and connections to the detector bias voltage supply, to a DC power supply for the onboard electronics, and to an adjustable discrimination level. The large number of channels and the short time between beam interactions (16 nanoseconds) dictates the need for high speed and large bandwidth communication channels, and a power distribution system that can handle the high current draw of the electronics including the large AC component due to their switching. At the same time the constraints imposed by the physics measurements require that the cable plant have absolutely minimal mass and radiation length. 4 refs., 2 figs

  14. Prospects for polarization at RHIC and SSC

    International Nuclear Information System (INIS)

    Lee, S.Y.

    1991-01-01

    In low to medium energy accelerators, betatron tune jumps and vertical orbit harmonic correction methods have been used to overcome the intrinsic and imperfection resonances. At high energy accelerators, snakes are needed to preserve polarization. We analyze the effects of snake resonances, snake imperfections overlapping resonances on the spin depolarization. We discuss also results of recent snake experiments at the IUCF Cooler Ring. The snake can overcome various kinds of spin depolarization resonances. These experiments pointed out further that partial snake can be used to cure the imperfection resonances in low to medium energy accelerators. We also examine various snake designs. A new generalized snake concept allows for two possible configurations. The compact configuration offers the advantages of shorter total snake length and smaller horizontal orbit displacement. The split snake configuration allows for dual functions of a snake and a 90 degree spin rotator at the mid-section of the snake, which provides helicity state collisions. The requirements for obtaining high luminosity polarized protons at high energy colliders, such as RHIC and SSC, are reviewed

  15. Engineering innovations on the SSC DTL accelerator

    International Nuclear Information System (INIS)

    Rymer, J.P.; Potter, J.M.; Givens, J.; Campbell, B.; Hansborough, L.

    1992-01-01

    The engineering design of the drift-tube linac (DTL) tanks for the Superconducting Super Collider (SSC) linac incorporates numerous innovative features, resulting in a reliable, cost-effective accelerator structure suitable for commercial production. The tank structure includes two integral strong-backs that provide stable mounting surfaces for the drift tubes and ion pumps and add mechanical stiffness. Drift tubes are mounted using AccSys' patented semi-hard socket technique, which includes separate metal seals for rf and vacuum. The socket allows repeatable adjustment of drift-tube location, thus allowing the tank to be fabricated to realistic tolerances. Transverse alignment of the drift tubes will be accomplished using a pulsed taut-wire technique to align the magnetic centers of the permanent magnet quadrupoles. This technique has been improved to allow drift-tube alignment throughout a 6 m long tank. For maximum reliability, the individual drift tubes include water-cooling channels that have no water-to-vacuum joints. Each tank will be driven through a waveguide iris coupler that can be adjusted to optimize the coupling. (Author) 3 refs., 3 figs

  16. GIS/FIS development for the SSC

    International Nuclear Information System (INIS)

    Oslin, A.; Butalla, M.

    1992-03-01

    Throughout all phases of the Superconducting Super Collider Laboratory (SSCL) project life decisions will be made on how to manage complex interactions of components, systems, and people with each other and with their environment at both micro and macro scales. The SSC has a distinct advantage compared to other large projects constructed and operated in the past, for even in the early phases scientists and engineers can use computer technology to provide faster computation and better modeling capability to resolve conflict and to make design, construction, and installation decisions. Computer systems today let us go beyond just making pictures of the components and objects under consideration. Not only can we know what objects look like, but we can visualize what and where they are, how they fit together to make networks, and how the networks relate to other types of objects and networks. Two such computer-based systems that relate object position and attributes to one another are Geographic Information Systems (GIS) and Facility Information Systems (FIS)

  17. Field measuring probe for SSC magnets

    International Nuclear Information System (INIS)

    Ganetis, G.; Herrera, J.; Hogue, R.; Skaritka, J.; Wanderer, P.; Willen, E.

    1987-01-01

    The field probe developed for measuring the field in SSC dipole magnets is an adaptation of the rotating tangential coil system in use at Brookhaven for several years. Also known as the MOLE, it is a self-contained room-temperature mechanism that is pulled through the aperture of the magnet with regular stops to measure the local field. Several minutes are required to measure the field at each point. The probe measures the multipole components of the field as well as the field angle relative to gravity. The sensitivity of the coil and electronics is such that the field up to the full 6.6 T excitation of the magnet as well as the field when warm with only 0.01 T excitation can be measured. Tethers are attached to both ends of the probe to carry electrical connections and to supply dry nitrogen to the air motors that rotate the tangential windings as well as the gravity sensor. A small computer is attached to the probe for control and for data collection, analysis and storage

  18. Radionuclide content of wastewater and solid waste from a low-level effluent treatment plant

    International Nuclear Information System (INIS)

    Muhamat Omar; Zalina Laili; Nik Marzukee Nik Ibrahim; Mat Bakar Mahusin

    2010-01-01

    A study on radioactivity levels of wastewater and solid waste from a Low-level Effluent Treatment Plant has been carried out. The measurement of radionuclide concentration was carried out using gamma spectrometry. Natural and anthropogenic radionuclides were detected in solid radioactive waste recovered from the treatment plant. The presence of radionuclides in waste water varies depending on activities carried out in laboratories and facilities connected to the plant. (author)

  19. Heavy neutrinos and new bosons at the SSC

    International Nuclear Information System (INIS)

    Kayser, B.; Deshpande, N.; Gunion, J.F.

    1984-01-01

    Methods for seeking and studying heavy neutrinos and new W bosons at the SSC are considered. Such particles are predicted by left-right symmetric models. Their properties and experimental signatures are analyzed. 25 refs., 5 figs

  20. Status of superconducting magnet development (SSC, RHIC, LHC)

    International Nuclear Information System (INIS)

    Wanderer, P.

    1993-01-01

    This paper summarize recent superconducting accelerator magnet construction and test activities at the Superconducting Super Collider Laboratory (SSC), the Large Hadron Collider at CERN (LHC), and the Relativistic Heavy Ion Collider at Brookhaven (RHIC). Future plan are also presented

  1. Orbit correction system for the SSC interaction regions

    International Nuclear Information System (INIS)

    Nosochkov, Y.; Pilat, F.; Ritson, D.M.

    1994-01-01

    In this paper we review our design of the orbit correction system for the SSC interaction regions, and discuss the principles of the local orbit correction at the IP. copyright 1994 American Institute of Physics

  2. Status of superconducting magnet development (SSC, RHIC, LHC)

    International Nuclear Information System (INIS)

    Wanderer, P.

    1993-01-01

    This paper summarizes recent superconducting accelerator magnet construction and test activities at the Superconducting Super Collider Laboratory (SSC), the Large Hardon Collider at CERN (LHC), and the Relativistic Heavy Ion Collider at Brookhaven (RHIC). Future plans are also presented

  3. Two dimensional magnetic field calculations for the SSC dipole magnets

    International Nuclear Information System (INIS)

    Krefta, M.P.; Pavlik, D.

    1991-01-01

    In this work two-dimensional methods are used to calculate the magnetic fields throughout the cross section of a SSC dipole magnet. Analytic techniques, which are based on closed form solutions to the defining field equations, are used to calculate the multipole content for any specified conductor positioning. The method is extended to investigate the effects of radial slots or keyways in the iron yoke. The multipole components of field, directly attributable to the slots or keyways, are examined as a function of size and location. It is shown that locating the slots or keyways at the magnet pole centers has a large effect on the multipole components; whereas, locating the keyways between the magnet poles has little effect on any of the multipoles. The investigation of nonlinear effects such as ferromagnetic saturation or superconductor magnetization relies on the use of numerical methods such as the finite element method. The errors associated with these codes are explained in terms of numerical round-off, spatial discretization error and the representation of distant boundaries. A method for increasing the accuracy of the multipole calculation from finite element solutions is set forth. It is shown that calculated multipole coefficients are sensitive to boundary conditions external to the cold mass during conditions of magnetic saturation

  4. SSC-K code user's manual

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Y.M.; Lee, Y.B.; Chang, W.P.; Hahn, D

    2000-07-01

    The Supper System Code of KAERI (SSC-K) is a best-estimate system code for analyzing a variety of off-normal or accidents in the heat transport system of a pool type LMR design. It is being developed at Korea Atomic Energy Research Inititution (KAERI) on the basis of SSC-L, originally developed at BNL to analyze loop-type LMR transients. SSC-K can handle both designs of loop and pool type LMRs. SSC-K contains detailed mechanistic models of transient thermal, hydraulic, neutronic, and mechanical phenomena to describe the response of the reactor core, coolant, fuel elements, and structures to accident conditions. This report provides an overview of recent model developmentsvfor the SSC-K computer code, focusing on phenomenological model descriptions for new thermal, hydraulic, neutronic, and mechnaical modules. A comprehensive description of the models for pool-type reactor is given in Chapters 2 and 3; the steady-state plant characterization, prior to the initiation of transient is described in Chapter 2 and their transient counterparts are discussed in Chapter 3. In Chapter 4, a discussion on the intermediate heat exchanger (IHX) is presented. The IHX model of SSC-K is similar to that used in the SSC-L, except for some changes required for the pool-type configuration of reactor vessel. In Chapter 5, an electromagnetic (EM) pump is modeled as a component. There are two pump choices available in SSC-K; a centrifugal pump which was originally imbedded into the SSC-L, and an EM pump which was introduced for the KALIMER design. In Chapter 6, a model of passive safety decay heat removal system(PSDRS) is discussed, which removes decay heat through the reactor and containment vessel walls to the ambient air heat sink. In Chapter 7, models for various reactivity feedback effects are discussed. Reactivity effects of importance in fast reactor include the Doppler effect, effects of sodium density changes, effects of dimensional changes in core geometry. Finally in Chapter 8

  5. SSC-K code users manual (rev.1)

    International Nuclear Information System (INIS)

    Kwon, Y. M.; Lee, Y. B.; Chang, W. P.; Hahn, D.

    2002-01-01

    The Supper System Code of KAERI (SSC-K) is a best-estimate system code for analyzing a variety of off-normal or accidents in the heat transport system of a pool type LMR design. It is being developed at Korea Atomic Energy Research Institution (KAERI) on the basis of SSC-L, originally developed at BNL to analyze loop-type LMR transients. SSC-K can handle both designs of loop and pool type LMRs. SSC-K contains detailed mechanistic models of transient thermal, hydraulic, neutronic, and mechanical phenomena to describe the response of the reactor core, coolant, fuel elements, and structures to accident conditions. This report provides a revised User's Manual (rev.1) of the SSC-K computer code, focusing on phenomenological model descriptions for new thermal, hydraulic, neutronic, and mechanical modules. A comprehensive description of the models for pool-type reactor is given in Chapters 2 and 3; the steady-state plant characterization, prior to the initiation of transient is described in Chapter 2 and their transient counterparts are discussed in Chapter 3. Discussions on the intermediate heat exchanger (IHX) and the electromagnetic (EM) pump are described in Chapter 4 and 5, respectively. A model of passive safety decay heat removal system (PSDRS) is discussed in Chapter 6, and models for various reactivity feedback effects are discussed in Chapter 7. In Chapter 8, constitutive laws and correlations required to execute the SSC-K are described. New models developed for SSC-K rev.1 are two dimensional hot pool model in Chapter 9, and long term cooling model in Chapter 10. Finally, a brief description of MINET code adopted to simulate BOP is presented in Chapter 11. Based on test runs for typical LMFBR accident analyses, it was found that the present version of SSC-K would be used for the safety analysis of KALIMER. However, the further validation of SSC-K is required for real applications. It is noted that the user's manual of SSC-K will be revised later with the

  6. Content

    DEFF Research Database (Denmark)

    Keiding, Tina Bering

    secondary levels. In subject matter didactics, the question of content is more developed, but it is still mostly confined to teaching on lower levels. As for higher education didactics, discussions on selection of content are almost non-existent on the programmatic level. Nevertheless, teachers are forced...... curriculum, in higher education, and to generate analytical categories and criteria for selection of content, which can be used for systematic didactical reflection. The larger project also concerns reflection on and clarification of the concept of content, including the relation between content at the level......Aim, content and methods are fundamental categories of both theoretical and practical general didactics. A quick glance in recent pedagogical literature on higher education, however, reveals a strong preoccupation with methods, i.e. how teaching should be organized socially (Biggs & Tang, 2007...

  7. Underground measurements of seismic vibrations at the SSC site

    International Nuclear Information System (INIS)

    Shiltsev, V.D.; Parkhomchuk, V.V.; Weaver, H.J.

    1995-01-01

    The results of underground measurements of seismic vibrations at the tunnel depth of the Superconducting Super Collider (SSC) site are presented. Spectral analysis of the data obtained in the frequency band from 0.05 Hz to 1500 Hz is performed. It is found that amplitudes of ambient ground motion are less than requirements for the Collider, but cultural vibrations are unacceptably large and will cause fast growth of transverse emittance of the SSC beams

  8. Tracking simulation and wire chamber requirements for the SSC

    International Nuclear Information System (INIS)

    Hanson, G.G.; Niczyporuk, B.B.; Palounek, A.P.T.

    1988-11-01

    Limitations placed on wire chambers by radiation damage and rate requirements in the SSC environment are reviewed. Possible conceptual designs for wire chamber tracking systems which meet these requirements are discussed. Computer simulation studies of tracking in such systems are presented. Simulations of events from interesting physics at the SSC, including hits from minimum bias background events, are examined. Results of some preliminary pattern recognition studies are given. 16 refs., 16 figs., 2 tabs

  9. Effect of pre-weaning solid feed and milk intake on caecal content characteristics and performance of rabbits around weaning

    Directory of Open Access Journals (Sweden)

    Luca Juliano

    2010-01-01

    Full Text Available The aim of this study is to know the effect of different solid feed and milk intake during suckling on performance around weaning and on caecal content characteristics at weaning. In order to obtain different intakes of milk and solid feed, 13 litters of pregnant females (PF inseminated the day after delivery and 14 litters of non-pregnant females (NPF were compared. At birth the litters were equalized at eight pups and during lactation dead pups were replaced by pups of the same age from nursing does. Compared to the PF group, rabbits in the NPF group had a higher milk intake (26.0 versus 21.4 g/day; P < 0.01 and lower solid feed intake (9.1 versus 11.5 g/day; P < 0.01 between 20 and 28 days of age. No significant difference was observed between the two groups in weight gain before and post-weaning (28-49 days. At weaning, the rabbits in group PF showed higher values in caecal content (g 26.3 versus 22.6; P < 0.05 and volatile fatty acids (mmol/l 52.2 versus 43.6; P < 0.01 and lower values in empty caecal weight (g 7.18 versus 7.78; P < 0.05, C3 (6.4 versus 9.3%; P < 0.01 and C3/C4 ratio (0.39 versus 0.63; P < 0.01 than the group NPF. On the basis of the above results, it may be concluded that the quantity of solid feed and milk intake before weaning influenced the charac- teristics of the caecal content, but not the performance of rabbits around weaning.

  10. Thermomagnetic method to determine cobalt content in solid WC-Co alloys

    International Nuclear Information System (INIS)

    Tumanov, V.I.; Loshakov, A.L.; Korchakova, E.A.

    1980-01-01

    A thermomagnetic method of cobalt amount determination in tungsten solid alloys is suggested. The method consists in the following: a sample of solid alloy is placed in a magnetic field sufficient to achieve technical saturation (not less than 10 kOe), and specific magnetization of saturation of the alloy σ is determined, then the sample is heated and according to the curves of magnetic permeability dependence on the temperature the Curie point of the alloy THETA is determined and cobalt amount is calculated by the formula qsub(Co)=σ100/(kTHETA+b). The analysis duration is approximately 30 min. Comparative data of cobalt amount determination in solid alloys WC-Co using thermonagnetic and potentiometric methods are presented. Results obtained by thermomagnetic and chemical method are in good agreement. Efficiency of the thermomagnetic method is much higher

  11. Effect of total solids content on methane and volatile fatty acid production in anaerobic digestion of food waste.

    Science.gov (United States)

    Liotta, Flavia; d'Antonio, Giuseppe; Esposito, Giovanni; Fabbricino, Massimiliano; van Hullebusch, Eric D; Lens, Piet N L; Pirozzi, Francesco; Pontoni, Ludovico

    2014-10-01

    This work investigates the role of the moisture content on anaerobic digestion of food waste, as representative of rapidly biodegradable substrates, analysing the role of volatile fatty acid production on process kinetics. A range of total solids from 4.5% to 19.2% is considered in order to compare methane yields and kinetics of reactors operated under wet to dry conditions. The experimental results show a reduction of the specific final methane yield of 4.3% and 40.8% in semi-dry and dry conditions compared with wet conditions. A decreasing trend of the specific initial methane production rate is observed when increasing the total solids concentration. Because of lack of water, volatile fatty acids accumulation occurs during the first step of the process at semi-dry and dry conditions, which is considered to be responsible for the reduction of process kinetic rates. The total volatile fatty acids concentration and speciation are proposed as indicators of process development at different total solids content. © The Author(s) 2014.

  12. Effect of solid state fermentation on nutrient content and ileal amino acids digestibility of canola meal in broiler chickens

    Directory of Open Access Journals (Sweden)

    Aljuobori Ahmed

    2014-06-01

    Full Text Available The aim of the current study was to investigate the potential of Lactobacillus salivarius solid state fermentation for reduction of glucosinolate content in canola meal (CM as well as the improvement of its nutrient digestibility for broiler chickens. Canola meal was treated with the L. salivarius in solid state fermentation for 30 days. Nutrients ileal digestibility was tested using 42-day-old broilers fed by either CM or fermented CM (FCM as the sole source of energy and protein. The results showed that fermentation of CM using L. salivarius reduced glucosinolate content of CM by 38%. The digestibility coefficient was improved significantly for crude protein, Met, Cys, Arg, Asp, Glu, and Ser in FCM compared to CM. However, apparent metabolisable energy of CM was not affected by fermentation. It appears that fermentation treatment of CM using L. salivarius may improve the overall nutritive value of CM for broiler chickens, reducing its total glucosinolate and crude fibre content by 38 and 16%, respectively.

  13. [Impact of Thermal Treatment on Biogas Production by Anaerobic Digestion of High-solid-content Swine Manure].

    Science.gov (United States)

    Hu, Yu-ying; Wu, Jing; Wang, Shi-feng; Cao, Zhi-ping; Wang, Kai-jun; Zuo, Jian-e

    2015-08-01

    Livestock manure is a kind of waste with high organic content and sanitation risk. In order to investigate the impact of thermal treatment on the anaerobic digestion of high-solid-content swine manure, 70 degrees C thermal treatment was conducted to treat raw manure (solid content 27.6%) without any dilution. The results indicated that thermal treatment could reduce the organic matters and improve the performance of anaerobic digestion. When the thermal treatment time was 1d, 2d, 3d, 4d, the VS removal rates were 15.1%, 15.5%, 17.8% and 20.0%, respectively. The methane production rates (CH4/VSadd) were 284.4, 296.3, 309.2 and 264.4 mL x g(-1), which was enhanced by 49.7%, 55.9%, 62.7% and 39.2%, respectively. The highest methane production rate occurred when the thermal treatment time was 3d. The thermal treatment had an efficient impact on promoting the performance of methane production rate with a suitable energy consumption. On the other hand, thermal treatment could act as pasteurization. This showed that thermal treatment would be of great practical importance.

  14. Mechanical properties, phenolic composition and extractability indices of Barbera grapes of different soluble solids contents from several growing areas.

    Science.gov (United States)

    Torchio, Fabrizio; Cagnasso, Enzo; Gerbi, Vincenzo; Rolle, Luca

    2010-02-15

    Phenolic compounds, extractable from grape skins and seeds, have a notable influence on the quality of red wines. Many studies have clearly demonstrated the relationship between the phenolic composition of the grape at harvest time and its influence on the phenolic composition of the red wine produced. In many previous works the evolution of phenolic composition and relative extractability was normally studied on grapes sampled at different times during ripening, but at the same date the physiological characteristics of grape berries in a vineyard are often very heterogeneous. Therefore, the main goal of the study is to investigate the differences among mechanical properties, phenolic composition and relative extractability of Vitis vinifera L. cv Barbera grape berries, harvested at the same date from several vineyards, and calibrated according to their density at three levels of soluble solids (A=235+/-8, B=252+/-8 and C=269+/-8 g L(-1) sugar) with the aim of studying the influence of ripeness stages and growing locations on these parameters. Results on mechanical properties showed that the thickness of the berry skin (Sp(sk)) was the parameter most affected by the different level of sugars in the pulp, while different skin hardnesses, evaluated by the break skin force (F(sk)), were related to the cultivation sites. The latter were also observed to influence the mechanical characteristics of seeds. Generally, the anthocyanin content increased with the level of soluble solids, while the increase in the tannin content of the berry skin and seeds was less marked. However, significant changes in flavanols reactive to vanillin in the seeds were found. The cellular maturity index (EA%) was little influenced by the soluble solids content of grapes. Copyright 2009 Elsevier B.V. All rights reserved.

  15. Effect of sucrose polyesters on crystallization rate of vegetable ghee: solid fat content study

    Directory of Open Access Journals (Sweden)

    Ibrahim Nasir, Mohammad

    2003-12-01

    Full Text Available Crystallization rate of partial hydrogenated blend of soybean oil and cottonseed oil used for making vegetable ghee (vanaspati was investigated, by solid fat content (SFC using pulsed nuclear magnetic resonance (p-NMR. The effects of adding sucrose fatty acid esters or sucrose polyesters (SPE on the crystallization rate of the blend fat were studied. Sucrose tetrastearate DK ester F-10 (stearate 70% - palmitate 30% was added to the fat at different concentration, namely 0.5% and 1.0%. Blank sample and sample containing 0.5% and 1.0% DK ester F-10 / (DK F-10 were chosen to measure the change in SFC at constant temperature of 15ºC for a period of 25 hr. Five determinations of SFC were taken to the fat samples during the 25 hr i.e. 2,5,9,13 and 25th hr. SFC vs. time of crystallization of the three samples showed continuous increasing in SFC in all samples during the 25 hr, with sharp increasing at the first two hours. Samples containing 0.0% and 0.5% DK F-10, showed no significant difference in SFC during the first thirteen hours, while sample containing 1.0% DK F-10, showed higher SFC than the other two samples, through out the period. The amount of SFC for 1.0% DK F-10 sample at the 13th hour is equal to the SFC of the blank (0.0% sample at the 25th hour. Melting point of the same samples increased with the increasing DK F-10 concentration in the fat samples. The results of SFC make it sure that the addition of 1.0% DK F- 10 will shorten the time required for the crystallization of vegetable ghee while the addition of 0.5% will not have significant effect.Se ha investigado, mediante el contenido en grasa sólida (SFC por resonancia magnética nuclear pulsada (p-NMR, la velocidad de cristalización de mezcla de aceite de la soja y aceite de semilla del algodón parcialmente hidrogenada utilizada en la elaboración de ghee vegetal (vanaspati. Se han estudiado los efectos de añadir ésteres de sacarosa de ácidos grasos o poliésteres de

  16. Simultaneous Effects of Total Solids Content, Milk Base, Heat Treatment Temperature and Sample Temperature on the Rheological Properties of Plain Stirred Yogurt

    Directory of Open Access Journals (Sweden)

    Attilio Converti

    2006-01-01

    Full Text Available Response surface methodology was used to establish a relationship between total solids content, milk base, heat treatment temperature, and sample temperature, and consistency index, flow behaviour index, and apparent viscosity of plain stirred yogurts. Statistical treatments resulted in developments of mathematical models. All samples presented shear thinning fluid behaviour. The increase of the content of total solids (9.3–22.7 % and milk base heat treatment temperature (81.6–98.4 °C resulted in a significant increase in consistency index and a decrease in flow behaviour index. Increase in the sample temperature (1.6–18.4 °C caused a decrease in consistency index and increase in flow behaviour index. Apparent viscosity was directly related to the content of total solids. Rheological properties of yogurt were highly dependent on the content of total solids in milk.

  17. A parallel non-neural trigger tracker for the SSC

    International Nuclear Information System (INIS)

    Farber, R.M.; Kennison, W.; Lapedes, A.S.

    1991-01-01

    The Superconducting Super Collider (SSC) is a major project promising to open the vistas of very high particle physics. When the SSC is in operation, data will be produced at a staggering rate. Current estimates place the raw data coming our of the proposed silicon detector system at 2.5 x 10 16 bits/second. Clearly, storing all events for later off-line processing is totally impracticable. A hierarchy of triggers, firing only on events meeting increasingly specific criteria, are planned to cull interesting events from the flood of information. Each event consists of a sequence of isolated ''hits'', caused by particles hitting various parts of the detector. Collating these hits into the tracks of the approximately 500 particles/event, and then quickly deciding which events meet the criteria for later processing, is essential if the SSC is to produce usable information. This paper addresses the need for real-time triggering and track reconstruction. A benchmarked and buildable algorithm, operable at the required data rates, is described. The use of neural nets, suggested by other researchers, is specifically avoided as unnecessary and impractical. Instead, a parallel algorithm, and associated hardware architecture using only conventional technology, is presented. The algorithm has been tested on fully scaled up, extensively detailed, simulated SSC events, with extremely encouraging results. Preliminary hardware analysis indicate that the trigger/tracker may be built within proposed SSC budget guidelines. 7 refs., 4 figs

  18. Effect of sewage sludge content on gas quality and solid residues produced by cogasification in an updraft gasifier

    Energy Technology Data Exchange (ETDEWEB)

    Seggiani, Maurizia, E-mail: m.seggiani@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy); Puccini, Monica, E-mail: m.puccini@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy); Raggio, Giovanni, E-mail: g.raggio@tiscali.it [Italprogetti Engineering SPA, Lungarno Pacinotti, 59/A, 56020 San Romano (Pisa) (Italy); Vitolo, Sandra, E-mail: s.vitolo@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy)

    2012-10-15

    Highlights: Black-Right-Pointing-Pointer Cogasification of sewage sludge with wood pellets in updraft gasifier was analysed. Black-Right-Pointing-Pointer The effects of sewage sludge content on the gasification process were examined. Black-Right-Pointing-Pointer Sewage sludge addition up to 30 wt.% reduces moderately the process performance. Black-Right-Pointing-Pointer At high sewage sludge content slagging and clinker formation occurred. Black-Right-Pointing-Pointer Solid residues produced resulted acceptable at landfills for non-hazardous waste. - Abstract: In the present work, the gasification with air of dehydrated sewage sludge (SS) with 20 wt.% moisture mixed with conventional woody biomass was investigated using a pilot fixed-bed updraft gasifier. Attention was focused on the effect of the SS content on the gasification performance and on the environmental impact of the process. The results showed that it is possible to co-gasify SS with wood pellets (WPs) in updraft fixed-bed gasification installations. However, at high content of sewage sludge the gasification process can become instable because of the very high ash content and low ash fusion temperatures of SS. At an equivalent ratio of 0.25, compared with wood pellets gasification, the addition of sewage sludge led to a reduction of gas yield in favor of an increase of condensate production with consequent cold gas efficiency decrease. Low concentrations of dioxins/furans and PAHs were measured in the gas produced by SS gasification, well below the limiting values for the exhaust gaseous emissions. NH{sub 3}, HCl and HF contents were very low because most of these compounds were retained in the wet scrubber systems. On the other hand, high H{sub 2}S levels were measured due to high sulfur content of SS. Heavy metals supplied with the feedstocks were mostly retained in gasification solid residues. The leachability tests performed according to European regulations showed that metals leachability was

  19. Determination of alpha activity and fissile mass content in solid waste by systems using neutron interrogation

    International Nuclear Information System (INIS)

    Romeyer Dherbey, J.; Lacruche, G.; Berne, R.; Auge, J.; Martin Deidier, L.; Butez, M.

    1990-01-01

    The Quantitative control (determination of heavy nuclides and alpha activity) of alpha radioactive wastes is necessary, particularly to determine if the waste is in accordance with the surface storage limits. In order to reduce the uncertainty on the alpha activity resulting from unknown isotopic composition, inhomogeneity of heavy nuclides in the matrix, combination of several methods is necessary. In the paper we present the Cadarache development work in the NDA of solid waste using the Californium shuffler, 14 Mev neutron generator, and also passive techniques such as neutron emission measurement and gamma spectrometry. Experimental systems combining active and passive methods are presented (COSAC, BANCO, DANAIDE, PROMETHEE)

  20. Production and characterization refuse derived fuel (RDF) from high organic and moisture contents of municipal solid waste (MSW)

    Science.gov (United States)

    Dianda, P.; Mahidin; Munawar, E.

    2018-03-01

    Many cities in developing countries is facing a serious problems to dealing with huge municipal solid waste (MSW) generated. The main approach to manage MSW is causes environmental impact associated with the leachate and landfill gas emissions. On the other hand, the energy available also limited by rapid growth of population and economic development due to shortage of the natural resource. In this study, the potential utilized of MSW to produce refuse derived fuel (RDF) was investigate. The RDF was produced with various organic waste content. Then, the RDF was subjected to laboratory analysis to determine its characteristic including the calorific value. The results shows the moisture content was increased by increasing organic waste content, while the calorific value was found 17-36 MJ/kg. The highest calorific value was about 36 MJ/kg obtained at RDF with 40% organic waste content. This results indicated that the RDF can be use to substitute coal in main burning process and calcinations of cement industry.

  1. The Super Fixed Target beauty facility at the SSC

    International Nuclear Information System (INIS)

    Lau, Kwong

    1991-01-01

    The rationale for pursuing beauty physics at the SSC in a fixed target configuration is described. The increased beauty production cross section at the SSC, combined with high interaction rate capability of the proposed detector, results in 10 10-11 produced BB events per year. The long decay length of the B hadrons (≅ 10 cm) allows direct observation of B decays in the high resolution silicon microstrip vertex detector. To optimize the operation of the proposed beauty spectrometer and the SSC, parasitic extraction of attendant or artificially generated large amplitude protons using crystal channeling is proposed and explored. The large sample of fully reconstructed B events allows detailed studies of various CP violating decays with requisite statistics to confront the standard model. The CP physics potential of the proposed experiment is evaluated and compared with alternative approaches, such as symmetric e + e - B Factories and specialized hadron colliders

  2. SSC RIAR is the largest centre of research reactors

    International Nuclear Information System (INIS)

    Kalygin, V.V.

    1997-01-01

    The State Scientific Centre (SSC) ''Research Institute of Atomic Reactors'' (RIAR) is situated 100 km to the south-east from Moscow, in Dimitrovgrad, the Volga Region of the Russian Federation. SSC RIAR is the largest centre of research reactors in Russia. At present there are 5 types of reactor facilities in operation, including two NPP. One of the main tasks the Centre is the investigations on safety increase for power reactors. Broad international connections are available at the Institute. On the basis of the SSC RIAR during 3 years work has been done on the development of the branch training centre (TC) for the training of operation personnel of research and pilot reactors in Russia. (author). 3 tabs

  3. SSC RIAR is the largest centre of research reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kalygin, V V [State Scientific Centre, Research Inst. of Atomic Reactors (Russian Federation)

    1997-10-01

    The State Scientific Centre (SSC) ``Research Institute of Atomic Reactors`` (RIAR) is situated 100 km to the south-east from Moscow, in Dimitrovgrad, the Volga Region of the Russian Federation. SSC RIAR is the largest centre of research reactors in Russia. At present there are 5 types of reactor facilities in operation, including two NPP. One of the main tasks the Centre is the investigations on safety increase for power reactors. Broad international connections are available at the Institute. On the basis of the SSC RIAR during 3 years work has been done on the development of the branch training centre (TC) for the training of operation personnel of research and pilot reactors in Russia. (author). 3 tabs.

  4. An engineering design network for SSC detector development

    International Nuclear Information System (INIS)

    DiGiacomo, N.J.

    1990-01-01

    The detector systems that are being proposed to exploit the capabilities of the SSC are of a scale and scope that will make them among the most complex devices ever built. To successfully design and build these systems over the next decade, the authors must make use of integrated state of the art computer aided engineering and design (CAE/CAD) tools that have been developed and employed in industry. The challenge is to made these tools and associated engineering resources available to the spectrum of institutions - large and small universities, industries and national labs - involved in SSC detector development in such a way that each may contribute and participate in the most effective manner. The authors believe that powerful workstations running sophisticated modeling, analysis and simulation software, linked by high speed data networks and governed by modern configuration management methods offer the ideal means of arriving at the optimum detector configuration for physics at the SSC

  5. A high gradient quadrupole magnet for the SSC

    International Nuclear Information System (INIS)

    Taylor, C.; Caspi, S.; Helm, M.; Mirk, K.; Peters, C.; Wandesforde, A.

    1987-01-01

    A quadrupole magnet for the SSC has been designed with a gradient of 234 T/m at 6500 A. Coil I.D. is 40 mm. The two-layer windings have 9 inner turns and 13 outer turns per pole with a wedge-shaped space in each layer. The 30-strand cable is identical to that used in the outer layer of the SSC dipole magnet. Interlocking aluminum alloy collars are compressed around the coil using a four-way press and are locked with four keys. The collared coil is supported and centered in a cold split iron yoke. A one-meter model was constructed and tested. Design details including quench behavior are presented. The quadrupole magnets proposed for the main SSC rings have a design gradient of 230 T/m. For one proposed 60 degree lattice cell, each 3-m long quad is separated by five 17-m long dipole magnets

  6. Preliminary design implications of SSC fixed-target operation

    International Nuclear Information System (INIS)

    Zisman, M.S.

    1984-06-01

    This paper covers some of the accelerator physics issues relevant to a possible fixed-target operating mode for the Superconducting Super Collider (SSC). In the brief time available, no attempt has been made to design this capability into the SSC. Rather, I have tried to evaluate what the performance of such a machine might be, and to indicate the hardware implications and extraction considerations that would be part of an actual design study. Where appropriate, parameters and properties of the present LBL design for the SSC have been used; these should be taken as being representative of the general class of small-aperture, high-field colliders being considered by the accelerator physics community. Thus, the numerical examples given here must ultimately be reexamined in light of the actual parameters of the particular accelerator being considered

  7. The composition, heating value and renewable share of the energy content of mixed municipal solid waste in Finland

    International Nuclear Information System (INIS)

    Horttanainen, M.; Teirasvuo, N.; Kapustina, V.; Hupponen, M.; Luoranen, M.

    2013-01-01

    Highlights: • New experimental data of mixed MSW properties in a Finnish case region. • The share of renewable energy of mixed MSW. • The results were compared with earlier international studies. • The average share of renewable energy was 30% and the average LHVar 19 MJ/kg. • Well operating source separation decreases the renewable energy content of MSW. - Abstract: For the estimation of greenhouse gas emissions from waste incineration it is essential to know the share of the renewable energy content of the combusted waste. The composition and heating value information is generally available, but the renewable energy share or heating values of different fractions of waste have rarely been determined. In this study, data from Finnish studies concerning the composition and energy content of mixed MSW were collected, new experimental data on the compositions, heating values and renewable share of energy were presented and the results were compared to the estimations concluded from earlier international studies. In the town of Lappeenranta in south-eastern Finland, the share of renewable energy ranged between 25% and 34% in the energy content tests implemented for two sample trucks. The heating values of the waste and fractions of plastic waste were high in the samples compared to the earlier studies in Finland. These high values were caused by good source separation and led to a low share of renewable energy content in the waste. The results showed that in mixed municipal solid waste the renewable share of the energy content can be significantly lower than the general assumptions (50–60%) when the source separation of organic waste, paper and cardboard is carried out successfully. The number of samples was however small for making extensive conclusions on the results concerning the heating values and renewable share of energy and additional research is needed for this purpose

  8. The composition, heating value and renewable share of the energy content of mixed municipal solid waste in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Horttanainen, M., E-mail: mika.horttanainen@lut.fi; Teirasvuo, N.; Kapustina, V.; Hupponen, M.; Luoranen, M.

    2013-12-15

    Highlights: • New experimental data of mixed MSW properties in a Finnish case region. • The share of renewable energy of mixed MSW. • The results were compared with earlier international studies. • The average share of renewable energy was 30% and the average LHVar 19 MJ/kg. • Well operating source separation decreases the renewable energy content of MSW. - Abstract: For the estimation of greenhouse gas emissions from waste incineration it is essential to know the share of the renewable energy content of the combusted waste. The composition and heating value information is generally available, but the renewable energy share or heating values of different fractions of waste have rarely been determined. In this study, data from Finnish studies concerning the composition and energy content of mixed MSW were collected, new experimental data on the compositions, heating values and renewable share of energy were presented and the results were compared to the estimations concluded from earlier international studies. In the town of Lappeenranta in south-eastern Finland, the share of renewable energy ranged between 25% and 34% in the energy content tests implemented for two sample trucks. The heating values of the waste and fractions of plastic waste were high in the samples compared to the earlier studies in Finland. These high values were caused by good source separation and led to a low share of renewable energy content in the waste. The results showed that in mixed municipal solid waste the renewable share of the energy content can be significantly lower than the general assumptions (50–60%) when the source separation of organic waste, paper and cardboard is carried out successfully. The number of samples was however small for making extensive conclusions on the results concerning the heating values and renewable share of energy and additional research is needed for this purpose.

  9. Solid waste leach characteristics and contaminant-sediment interactions Volume 2: Contaminant transport under unsaturated moisture contents

    International Nuclear Information System (INIS)

    Lindenmeier, C.W.; Serne, R.J.; Conca, J.L.

    1995-09-01

    The objectives of this report and subsequent volumes include describing progress on (1) development and optimization of experimental methods to quantify the release of contaminants from solid wastes and their subsequent interactions with unsaturated sediments and (2) the creation of empirical data that become input parameters to performance assessment (PA) analyses for future Hanford Site disposal units and baseline risk assessments for inactive and existing solid waste disposal units. For this report, efforts focused on developing methodologies to evaluate contaminant transport in Trench 8 (W-5 Burial Ground) sediments under unsaturated (vadose zone) conditions. To accomplish this task, a series of flow-through column tests were run using standard saturated column systems, Wierenga unsaturated column systems (both commercial and modified), and the Unsaturated Flow Apparatus (UFA). The reactants investigated were 85 Sr, 236 U, and 238 U as reactive tracers, and tritium as a non-reactive tracer. Results indicate that for moderately unsaturated conditions (volumetric water contents >50 % of saturation), the Wierenga system performed reasonably well such that long water residence times (50-147 h) were achieved, and reasonably good steady-state flow conditions were maintained. The major drawbacks in using this system for reactive tracer work included (1) the inability to achieve reproducible and constant moisture content below 50% of saturation, (2) the four to six month time required to complete a single test, and (3) the propensity for mechanical failure resulting from laboratory power outages during the prolonged testing period

  10. Cardboard proportions and total solids contents as driving factors in dry co-fermentation of food waste.

    Science.gov (United States)

    Capson-Tojo, Gabriel; Trably, Eric; Rouez, Maxime; Crest, Marion; Bernet, Nicolas; Steyer, Jean-Philippe; Delgenès, Jean-Philippe; Escudié, Renaud

    2018-01-01

    This study evaluated the influence of the co-substrate proportions (0-60% of cardboard in dry basis) and the initial total solid contents (20-40%) on the batch fermentation performance. Maximum hydrogen yields were obtained when mono-fermenting food waste at high solids contents (89mlH 2 ·gVS -1 ). The hydrogen yields were lower when increasing the proportions of cardboard. The lower hydrogen yields at higher proportions of cardboard were translated into higher yields of caproic acid (up to 70.1gCOD·kgCOD bio -1 ), produced by consumption of acetic acid and hydrogen. The highest substrate conversions were achieved at low proportions of cardboard, indicating a stabilization effect due to higher buffering capacities in co-fermentation. Clostridiales were predominant in all operational conditions. This study opens up new possibilities for using the cardboard proportions for controlling the production of high added-value products in dry co-fermentation of food waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. The SSC superconducting air core toroid design development

    International Nuclear Information System (INIS)

    Fields, T.; Carroll, A.; Chiang, I.H.; Frank, J.S.; Haggerty, J.; Littenberg, L.; Morse, W.; Strand, R.C.; Lau, K.; Weinstein, R.; McNeil, R.; Friedman, J.; Hafen, E.; Haridas, P.; Kendall, H.W.; Osborne, L.; Pless, I.; Rosenson, L.; Pope, B.; Jones, L.W.; Luton, J.N.; Bonanos, P.; Marx, M.; Pusateri, J.A.; Favale, A.; Gottesman, S.; Schneid, E.; Verdier, R.

    1990-01-01

    Superconducting air core toroids show great promise for use in a muon spectrometer for the SSC. Early studies by SUNY at Stony Brook funded by SSC Laboratory, have established the feasibility of building magnets of the required size. The toroid spectrometer consists of a central toroid with two end cap toroids. The configuration under development provides for muon trajectory measurement outside the magnetic volume. System level studies on support structure, assembly, cryogenic material selection, and power are performed. Resulting selected optimal design and assembly is described. 4 refs., 6 figs

  12. SSC Tenant Meeting: NASA Near Earth Network (NEN) Overview

    Science.gov (United States)

    Carter, David; Larsen, David; Baldwin, Philip; Wilson, Cristy; Ruley, LaMont

    2018-01-01

    The Near Earth Network (NEN) consists of globally distributed tracking stations that are strategically located throughout the world which provide Telemetry, Tracking, and Commanding (TTC) services support to a variety of orbital and suborbital flight missions, including Low Earth Orbit (LEO), Geosynchronous Earth Orbit (GEO), highly elliptical, and lunar orbits. Swedish Space Corporation (SSC), which is one of the NEN Commercial Service Provider, has provided the NEN with TTC services support from its Alaska, Hawaii, Chile and Sweden. The presentation will give an overview of the NEN and its support from SSC.

  13. Tevatron as an SSC prototype; experience versus predictions

    International Nuclear Information System (INIS)

    Johnson, R.P.

    1984-01-01

    Early machine experiments on the Tevatron which are relevant to the SSC are discussed. Despite the preliminary nature of the data, there have been some interesting observations which may influence the design of the SSC. In particular, comparisons of measured betatron tunes, chromaticities, and resonance line widths with those predicted from computer simulations using magnetic field measurements have been made; the predictability for low order phenomena seems acceptable. Coasting beam studies indicate long lifetime and lack of strong resonance driving terms. Low energy studies of beam behavior indicate that a dynamic range of a factor of 15 from injection to operation energy should be possible

  14. EMPACT: An alternative approach to a high PT SSC experiment

    International Nuclear Information System (INIS)

    Marx, M.; State Univ. of New York, Stony Brook, NY

    1989-05-01

    A survey of high P T detector concepts advanced for the SSC reveals two striking facts -- first, the scale of most detectors is set by the muon detection system; and second, that the performance of these muon systems is limited in comparison to electron or jet capabilities, either in resolution or in rapidity acceptance. I propose here an alternative concept for an SSC experiment which will provide enhanced muon performance at a level to that obtainable through calorimetric means for electrons and jets, while drastically reducing the tonnage of the experiment

  15. Heater induced quenches in SSC [Superconducting Super Collider] model dipoles

    International Nuclear Information System (INIS)

    Hassenzahl, W.V.

    1986-10-01

    A 1-m long SSC dipole constructed at the Lawrence Berkeley laboratory was subjected to a series of heater induced quenches to determine: axial quench propagation velocities, transverse quench propagation, and conductor temperature rise. Quenches were produced by 3 heaters at different locations in the magnet and at several currents. The results of these studies are described and are compared to previously published theoretical studies of quenches on the SSC dipoles. These results are shown to be in agreement with the calculations of the program ''QUENCH'', which includes an increase of the quench velocity during the first few milliseconds of the quench

  16. Radioactivation in ''quiet'' sections of the SSC [Superconducting Super Collider

    International Nuclear Information System (INIS)

    Cossairt, J.D.

    1987-10-01

    Estimation of induced radioactivity in the ''quiet'' sections of the SSC is approached using elementary methods. Estimates are given of total activity and residual dose rates on the surface of magnets in the quiet regions, as well as estimates of the activation of tunnel concrete. The residual radioactivity produced in the magnets and concrete walls of the ''quiet'' regions of the SSC are found to be quite small and of little radiological impact, but that simple scaling could yield results for more ''lossy'' regions

  17. Full length SSC R and D dipole magnet test results

    International Nuclear Information System (INIS)

    Strait, J.; Bleadon, M.; Brown, B.C.

    1989-03-01

    Four full scale SSC development dipole magnets have been tested for mechanical and quench behavior. Two are of a design similar to previous magnets but contain a number of improvements, including more uniform coil size, higher pre-stress and a redesigned inner-outer coil splice. One exceeds the SSC operating current on the second quench but the other appears to be limited by damaged superconductor to a lower current. The other two magnets are of alternate designs. One trains erratically and fails to reach a plateau and the other reaches plateau after four quenches. 12 refs., 4 figs

  18. Fixed target beauty physics from Tevatron to SSC (E771)

    International Nuclear Information System (INIS)

    Lau, K.

    1992-01-01

    The E771 beauty experiment at Fermilab is described. The Super Fixed Target Beauty Facility (SFT) proposal to perform fixed target beauty physics at the SSC is a natural evolution. The unique features of SFT include crystal channeling extraction from the SSC main ring, which allows the experiment to operate concurrently with the collider experiments. The slow extraction rate (≅2x10 8 protons/s) does not limit the lifetime of the stored beams. The proposed beauty spectrometer and its capability in CP violation studies are described. (author) 19 refs.; 2 figs.; 2 tabs

  19. A SIMPLE METHOD TO CONTROL THE MOISTURE CONTENT OF THE FERMENTING MEDIUM DURING LABORATORY-SCALE SOLID-STATE FERMENTATION EXPERIMENTS

    Directory of Open Access Journals (Sweden)

    W. BORZANI

    1999-03-01

    Full Text Available When the moisture content of the fermenting medium significantly decreases during laboratory-scale solid-state fermentation tests, the quantity of water to be periodically added to the medium in order to control its moisture content may be evaluated from the water evaporation rate of the non-inoculated medium.

  20. Influence of solid state fermentation by Trichoderma spp. on solubility, phenolic content, antioxidant, and antimicrobial activities of commercial turmeric.

    Science.gov (United States)

    Mohamed, Saleh A; Saleh, Rashad M; Kabli, Saleh A; Al-Garni, Saleh M

    2016-05-01

    The influence of solid state fermentation (SSF) by Trichoderma spp. on the solubility, total phenolic content, antioxidant, and antibacterial activities of turmeric was determined and compared with unfermented turmeric. The solubility of turmeric was monitored by increase in its phenolic content. The total phenolic content of turmeric extracted by 80% methanol and water after SSF by six species of Trichoderma spp. increased significantly from 2.5 to 11.3-23.3 and from 0.5 to 13.5-20.4 GAE/g DW, respectively. The antioxidant activities of fermented turmeric were enhanced using 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2'-azino-bis (3-ethylbenzo-thiazoline-6-sulfonic acid) (ABTS), and ferric ion-reducing antioxidant power (FRAP) assays. The antibacterial activity of fermented turmeric against human-pathogenic bacteria Escherichia coli, Streptococcus agalactiae, Staphylococcus aureus, Entreococcus faecalis, Methicillin-Resistant S. aureus, Klebsiella pneumonia, and Pseudomonas aeruginosae showed a broad spectrum inhibitory effect. In conclusion, the results indicated the potentials of using fermented turmeric as natural antioxidant and antimicrobial material for food applications.

  1. Bio-drying and size sorting of municipal solid waste with high water content for improving energy recovery.

    Science.gov (United States)

    Shao, Li-Ming; Ma, Zhong-He; Zhang, Hua; Zhang, Dong-Qing; He, Pin-Jing

    2010-07-01

    Bio-drying can enhance the sortability and heating value of municipal solid waste (MSW), consequently improving energy recovery. Bio-drying followed by size sorting was adopted for MSW with high water content to improve its combustibility and reduce potential environmental pollution during the follow-up incineration. The effects of bio-drying and waste particle size on heating values, acid gas and heavy metal emission potential were investigated. The results show that, the water content of MSW decreased from 73.0% to 48.3% after bio-drying, whereas its lower heating value (LHV) increased by 157%. The heavy metal concentrations increased by around 60% due to the loss of dry materials mainly resulting from biodegradation of food residues. The bio-dried waste fractions with particle size higher than 45 mm were mainly composed of plastics and papers, and were preferable for the production of refuse derived fuel (RDF) in view of higher LHV as well as lower heavy metal concentration and emission. However, due to the higher chlorine content and HCl emission potential, attention should be paid to acid gas and dioxin pollution control. Although LHVs of the waste fractions with size bio-drying, they were still below the quality standards for RDF and much higher heavy metal pollution potential was observed. Different incineration strategies could be adopted for different particle size fractions of MSW, regarding to their combustibility and pollution property. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

  2. The influence of total solids content and initial pH on batch biohydrogen production by solid substrate fermentation of agroindustrial wastes.

    Science.gov (United States)

    Robledo-Narváez, Paula N; Muñoz-Páez, Karla M; Poggi-Varaldo, Hector M; Ríos-Leal, Elvira; Calva-Calva, Graciano; Ortega-Clemente, L Alfredo; Rinderknecht-Seijas, Noemí; Estrada-Vázquez, Carlos; Ponce-Noyola, M Teresa; Salazar-Montoya, J Alfredo

    2013-10-15

    Hydrogen is a valuable clean energy source, and its production by biological processes is attractive and environmentally sound and friendly. In México 5 million tons/yr of agroindustrial wastes are generated; these residues are rich in fermentable organic matter that can be used for hydrogen production. On the other hand, batch, intermittently vented, solid substrate fermentation of organic waste has attracted interest in the last 10 years. Thus the objective of our work was to determine the effect of initial total solids content and initial pH on H2 production in batch fermentation of a substrate that consisted of a mixture of sugarcane bagasse, pineapple peelings, and waste activated sludge. The experiment was a response surface based on 2(2) factorial with central and axial points with initial TS (15-35%) and initial pH (6.5-7.5) as factors. Fermentation was carried out at 35 °C, with intermittent venting of minireactors and periodic flushing with inert N2 gas. Up to 5 cycles of H2 production were observed; the best treatment in our work showed cumulative H2 productions (ca. 3 mmol H2/gds) with 18% and 6.65 initial TS and pH, respectively. There was a significant effect of TS on production of hydrogen, the latter decreased with initial TS increase from 18% onwards. Cumulative H2 productions achieved in this work were higher than those reported for organic fraction of municipal solid waste (OFMSW) and mixtures of OFMSW and fruit peels waste from fruit juice industry, using the same process. Specific energetic potential due to H2 in our work was attractive and fell in the high side of the range of reported results in the open literature. Batch dark fermentation of agrowastes as practiced in our work could be useful for future biorefineries that generate biohydrogen as a first step and could influence the management of this type of agricultural wastes in México and other countries and regions as well. Copyright © 2013 Elsevier Ltd. All rights reserved.

  3. Searching for quark and lepton compositeness at the SSC

    International Nuclear Information System (INIS)

    Albright, C.H.; Bars, I.; Blumenfeld, B.

    1984-01-01

    We examine a variety of issues connected with searching for compositeness at the SSC. These include effects of resolution, alternative methods of looking for deviations from QCD predictions, advantages of polarized beams, and effects of compositeness on photon detection. We also consider how physics may look if the compositeness scale is as low as a few TeV. 17 refs

  4. Calculation of injection and extraction orbits for the IPCR SSC

    International Nuclear Information System (INIS)

    Goto, A.; Yano, Y.; Kishida, N.; Nakanishi, N.; Wada, T.

    1982-01-01

    Calculations of beam trajectories in the injection and extraction systems for the IPCR SSC were done and the characteristics of those elements were determined. Beam centering for single turn extraction by use of first harmonic fields were also studied. The rather simple conditions at the injection point for a well-centered acceleration orbit are also discussed

  5. Fermilab R and D test facility for SSC magnets

    International Nuclear Information System (INIS)

    Strait, J.; Bleadon, M.; Hanft, R.; Lamm, M.; McGuire, K.; Mantsch, P.; Mazur, P.O.; Orris, D.; Pachnik, J.

    1989-01-01

    The test facility used for R and D testing of full scale development dipole magnets for the SSC is described. The Fermilab Magnet Test Facility, originally built for production testing of Tevatron magnets, has been substantially modified to allow testing also of SSC magnets. Two of the original six test stands have been rebuilt to accommodate testing of SSC magnets at pressures between 1.3 Atm and 4 Atm and at temperatures between 1.8 K and 4.8 K and the power system has been modified to allow operation to at least 8 kA. Recent magnets have been heavily instrumented with voltage taps to allow detailed study of quench location and propagation and with strain gage based stress, force and motion transducers. A data acquisition system has been built with a capacity to read from each SSC test stand up to 220 electrical quench signals, 32 dynamic pressure, temperature and mechanical transducer signals during quench and up to 200 high precision, low time resolution, pressure, temperature and mechanical transducer signals. The quench detection and protection systems is also described. 23 refs., 4 figs. 2 tabs

  6. Cooldown and warmup computer simulations of the SSC ring

    International Nuclear Information System (INIS)

    Carcagno, R.H.; Schiesser, W.E.; Yuecel, A.

    1991-06-01

    The Superconducting Super Collider (SSC) consists of two stacked rings of superconducting magnets; each ring is about 86 km in circumference. The total mass to be cooled to liquid helium temperature amounts to about 1 x 10 8 kg, and the total helium inventory under nominal operating conditions (4.15 K and 4 atm) is about 2.8 x 10 5 kg. The cooldown and warmup process of a long string of magnets has to be well understood in order to design a cryogenic system that can satisfy the requirements of helium inventory handling, magnet temperature gradients, and process time for the different cooldown and warmup scenarios being planned for the SSC. A system that can be convincingly simulated can be understood, controlled, operated and improved in a systematic way. In this paper, we introduce two numerical models, a lumped model and a distributed model, for cooldown and warmup of the SSC ring, and present simulation results for an SSC string (4320 m long, or 1/20th of the full ring circumference). The models cover the temperature range between room and liquid helium temperature; the distributed model includes radial temperature distribution in the cold mass. Low temperature range simulations are particularly important to study inventory handling strategies because of the relationship between rapid changes in density and the system mass flow rate. 9 refs., 9 figs

  7. Probing the non-minimal Higgs sector at the SSC

    International Nuclear Information System (INIS)

    Gunion, J.F.; Haber, H.E.; Komamiya, S.; Yamamoto, H.; Barbaro-Galtieri, A.

    1987-11-01

    Non-minimal Higgs sectors occur in the Standard Model with more than one Higgs doublet, as well as in theories that go beyond the Standard Model. In this report, we discuss how Higgs search strategies must be altered, with respect to the Standard Model approaches, in order to probe the non-minimal Higgs sectors at the SSC

  8. Quench propagation across the copper wedges in SSC dipoles

    International Nuclear Information System (INIS)

    Ghosh, A.K.; Robins, K.E.; Sampson, W.B.

    1986-01-01

    The effect of copper wedges on quench propagation in SSC windings has been studied. The results indicate that the turn-to-turn quench transit time for conductors separated by an insulated copper wedge can be predicted with reasonable accuracy from the bulk quench properties and the mean wedge thickness

  9. Plans for industrial production of the SSC magnets

    International Nuclear Information System (INIS)

    Karpenko, V.N.; Rardin, D.C.

    1986-01-01

    The Universities Research Association through its Central Design Group is currently conducting research and development for the Department of Energy on a superconducting super collider (SSC). The proposed SSC is a device in which protons would be accelerated around a ring approximately 50 miles in circumference. The protons would be kept in their path by means of thousands of powerful superconducting magnets. Two such rings of magnets would be housed in a common underground tunnel, allowing groups of protons to be accelerated in opposite directions and collided, in order to study the fundamental nature of matter and energy. The magnet system is a major element of the SSC in terms of technical requirements, quantity of components and cost. In order to meet technical and production requirements imposed by this system early participation of industry is necessary. The program plans were developed with the objective to involve industry in the early stages of research and development of superconducting magnets, leading to cost effective processes of potential mass production of high quality accelerator magnets by industry. While a decision has not been made by the Department of Energy on whether or not to request construction of the SSC project, if such a request is made and the project is authorized and funded, it would lead to industrial manufacture of a large quantity of superconducting magnets

  10. Partial lifetime test of an SSC Collider dipole

    International Nuclear Information System (INIS)

    Wanderer, P.; Anerella, M.; Ganetis, G.

    1993-01-01

    Over a period of ten months, a 15 m-long, 50 mm-aperture superconducting SSC Collider dipole was taken through a series of thermal and power cycles to check for changes in performance. One quench below operating current was experienced during this period. Small changes in the coil preload and certain harmonics were observed

  11. Preaccident modeling of an LMFBR plant for SSC-L

    International Nuclear Information System (INIS)

    Agrawal, A.K.

    1976-12-01

    Physical models for various processes in preaccident or steady-state calculations for the entire liquid metal fast breeder reactor plant are described in this report. A computer program for this initialization phase was written to serve as the starting point for the transient version of the SSC-L code. All of the models and programming are applicable to the ''loop'' type plants

  12. Anti-proteinase 3 antibodies in diffuse systemic sclerosis (SSc with normotensive renal impairment: is it suggestive for an overlapping between SSc and idiopathic vasculitis?

    Directory of Open Access Journals (Sweden)

    V. Campanella

    2011-09-01

    Full Text Available Objective. To test the prevalence of anti-neutrophil cytoplasmic antibodies (ANCA in systemic sclerosis (SSc and to verify a possible association of ANCA with normotensive renal involvement in SSc. Patients and methods: 51 patients affected by SSc, 35 with diffuse scleroderma (dSSc and 16 with limited scleroderma (lSSc, were tested for ANCA by indirect immunofluorescence (IIF on human ethanol and formalin-acetone-fixed granulocytes (before and after DNase treatment, by conventional enzyme linked immuno-sorbent assay (ELISA and by capture-ELISA. Results. Six out of 51 selected SSc patients had ANCA by IIF (11.7% and five presented a perinuclear/nuclear atypical ANCA pattern. In all cases we only found anti-proteinase3 (aPR3 antibodies. All ANCA positive patients had diffuse form of SSc (17.1%, all were anti-Scl70 positive (aScl70, five patients had proteinuria, three had microscopic haematuria. All ANCA positive patients were normotensive with normal renin plasma levels, the mean erythrocyte sedimentation rate (ESR was higher in this group compared to the other SSc patients. Conclusions. Our study shows that aPR3 is not rare in dSSc. According to the clinical and serological findings and to the recent literature, we can hypothesise that when ANCA are found in SSc, an overlapping of scleroderma with systemic necrotizing vasculitis should be suspected.

  13. Reducing beryllium content in mixed bed solid-type breeder blankets

    Energy Technology Data Exchange (ETDEWEB)

    Shimwell, J., E-mail: mail@jshimwell.com [Department of Physics and Astronomy, University of Sheffield, Hicks Building, Hounsfield Road, Sheffield S3 7RH (United Kingdom); Lilley, S.; Morgan, L.; Packer, L.; Kovari, M.; Zheng, S. [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon, Oxfordshire OX14 3DB (United Kingdom); McMillan, J. [Department of Physics and Astronomy, University of Sheffield, Hicks Building, Hounsfield Road, Sheffield S3 7RH (United Kingdom)

    2016-11-01

    Highlights: • The ratio of breeder ceramic to neutron multiplier of breeder blankets was varied linearly with depth. • Blankets with varying composition were found to perform better than uniform composition breeder blankets. • It was also possible to reduce the amount of beryllium required by the blanket. - Abstract: Beryllium (Be) is a precious resource with many high value uses, the low energy threshold (n,2n) reaction makes Be an excellent neutron multiplier for use in fusion breeder blankets. Estimates of Be requirements and available resources suggest that this could represent a major supply difficulty for solid-type blanket concepts. Reducing the quantity of Be required by breeder blankets would help to alleviate the problem to some extent. In addition, it is important that the reduction in the Be quantity does not diminish the blanket's performance in key aspects such as the tritium breeding ratio (TBR), energy multiplication and peak nuclear heating. Mixed pebble bed designs allow for the multiplier fraction to be varied throughout the blanket. This neutronics study used MCNP 6 to investigate linear variations of the multiplier fraction in relation to blanket depth, in order to better utilise the important multiplying Be(n,2n) and breeding reactions. Blankets with a uniform multiplier fraction showed little scope for reduction in Be mass. Blankets with varying multiplier fractions were able to simultaneously use 10% less Be, increase the energy amplification by 1%, reduce the peak heating by 7% and maintaining a sufficient TBR when compared to the performance achievable using a uniform composition.

  14. The effect of gadolinium content on the thermal conductivity of near-stoichiometric (U,Gd)O2 solid solutions

    International Nuclear Information System (INIS)

    Fukushima, S.; Ohmichi, T.; Maeda, A.; Watanabe, H.

    1982-01-01

    The thermal conductivities of near-stoichiometric (U, Gd)O 2 solid solutions containing CdOsub(1.5) up to 15 mol% were determined in the temperature range 700 to 2000 K from thermal diffusivities measured by the laser flash method. Temperature dependence of the thermal conductivities up to around 1600 K could be expressed by the phonon conduction equation K = (A + BT) -1 . The thermal conductivity decreased gradually with an increase of gadolinium content. Thermal resistivities caused by lattice defects were calculated from a theoretical model considering U 4+ , U 5+ and Gd 3+ ions as phonon scattering centers. It was found that this model was in good agreement with the experimental results. The calculation based on this model indicates that the lattice strain effect on the lattice defect thermal resistivity is much larger than the mass effect. (orig.)

  15. The SSC dipole: Its conceptual origin and early design history

    International Nuclear Information System (INIS)

    Dahl, P.F.

    1992-05-01

    The magnet system for the Superconducting Super Collider will likely remain the most ambitions-and challenging-application of superconducting technology for the foreseeable future. The centerpiece of the system is the behemoth collider dipole magnet. Its design, still evolving in its detailed features, dates from the mid-1980's when it emerged as the winter in an early technical showdown that occupied the fledgling SSC project. In the present report we chronicle the origins and chief milestones in the development of certain SSC dipole design concepts. Unfortunately, the chronicle must remain incomplete, with the design not yet frozen as we go to press and still subject to important modifications as the SSC Laboratory settles in near its future home in Ellis County, Texas, hard on the heels of a wide-ranging design review in the closing days of the SSC Central Design Group in (CDG) Berkeley. Be that as it may, in what follows we concentrate on the early years in an attempt to recapitulate the birth of the dipole, taking as our point of departure the SSC Reference Designs Study (RDS) of 1984. In Section 3 we touch on the background for the various RDS options, including ISABELLE/CBA and the Tevatron. In Section 4 the narrative focuses on the two final protagonists, a high-field cosine theta (cos θ) magnet and a low-field superferric magnet. Section 5 recounts the circumstances surrounding the selection of a particular magnet ''style'' for further development, and the ups and downs of the first model magnets. We conclude with a smattering of progress highlights in refining the design during the final push under the reign of the CDG. Beyond that, the ongoing chronicle must be left for others to amplify and complete

  16. The SSC dipole: Its conceptual origin and early design history

    International Nuclear Information System (INIS)

    Dahl, P.F.

    1990-06-01

    The magnet system for the Superconducting Super Collider will likely remain the most ambitious -- and challenging -- application of superconducting technology for the foreseeable future. The centerpiece of the system is the behemoth collider dipole magnet. Its design, still evolving in its detailed features, dates from the mid-1980's when it emerged as the winner in an early technical showdown that occupied the fledgling SSC project. However, some of its gross features can be traced back to three path-breaking superconducting accelerator initiatives under way a decade earlier -- on the East Coast, on the West Coast, and in the Midwest. Other features have a still earlier legacy. In the present report we chronicle the origins and chief milestones in the development of certain SSC dipole design concepts. Unfortunately, the chronicle must remain incomplete, with the design not yet frozen as we go to press and still subject to important modifications as the SSC Laboratory settles in near its future home in Ellis County, Texas, hard on the heels of a wide-ranging design review in the closing days of the SSC Central Design Group in (CDG) Berkeley. Be that as it may, in what follows we concentrate on the early years in an attempt to recapitulate the birth of the dipole, taking as our point of departure the SSC Reference Designs Study (RDS) of 1984. In Section 3 we touch on the background for the various RDS options, including ISABELLE/CBA and the Tevatron. In Section 4 the narrative focuses on the two final protagonists, a high-field cosine theta (cos θ) magnet and a low-field superferric magnet. Section 5 recounts the circumstances surrounding the selection of a particular magnet ''style'' for further development, and the ups and downs of the first model magnets. We conclude with a smattering of progress highlights in refining the design during the final push under the reign of the CDG

  17. Optimization of solid content, carbon/nitrogen ratio and food/inoculum ratio for biogas production from food waste.

    Science.gov (United States)

    Dadaser-Celik, Filiz; Azgin, Sukru Taner; Yildiz, Yalcin Sevki

    2016-12-01

    Biogas production from food waste has been used as an efficient waste treatment option for years. The methane yields from decomposition of waste are, however, highly variable under different operating conditions. In this study, a statistical experimental design method (Taguchi OA 9 ) was implemented to investigate the effects of simultaneous variations of three parameters on methane production. The parameters investigated were solid content (SC), carbon/nitrogen ratio (C/N) and food/inoculum ratio (F/I). Two sets of experiments were conducted with nine anaerobic reactors operating under different conditions. Optimum conditions were determined using statistical analysis, such as analysis of variance (ANOVA). A confirmation experiment was carried out at optimum conditions to investigate the validity of the results. Statistical analysis showed that SC was the most important parameter for methane production with a 45% contribution, followed by F/I ratio with a 35% contribution. The optimum methane yield of 151 l kg -1 volatile solids (VS) was achieved after 24 days of digestion when SC was 4%, C/N was 28 and F/I were 0.3. The confirmation experiment provided a methane yield of 167 l kg -1 VS after 24 days. The analysis showed biogas production from food waste may be increased by optimization of operating conditions. © The Author(s) 2016.

  18. Health Effects Due to Radionuclides Content of Solid Minerals within Port of Richards Bay, South Africa

    Directory of Open Access Journals (Sweden)

    Felix B. Masok

    2016-11-01

    Full Text Available This study assessed the radiological health hazards to various body organs of workers working within Transnet Precinct in Richards Bay in Kwazulu-Natal, South Africa due to radionuclide content of mineral ores often stored within the facility. Thirty samples were collected from five mineral ores (rock phosphate, rutile, zircon, coal and hematite and analyzed for 238U, 234U, 226Ra, 210Pb, 235U, 232Th, 228Ra, 228Th and 40K using delayed neutron activation analysis and low energy gamma spectroscopy. Rutile was found to be the most radioactive mineral ore within the facility with 210Pb concentration of 759.00 ± 106.00 Bq·kg−1. Effective annual dose rate in (mSv·y−1 delivered to different organs of the body: testes, bone marrow, whole body, lungs and ovaries from mineral ores were such that dose from mineral ores decreased in the order coal > rutile > rock phosphate > hematite > zircon. The organs with the highest received dose rate were the testes and this received dose was from coal. However, all of the calculated absorbed dose rates to organs of the body were below the maximum permissible safety limits.

  19. Contents

    Directory of Open Access Journals (Sweden)

    Editor IJRED

    2012-11-01

    Full Text Available International Journal of Renewable Energy Development www.ijred.com Volume 1             Number 3            October 2012                ISSN 2252- 4940   CONTENTS OF ARTICLES page Design and Economic Analysis of a Photovoltaic System: A Case Study 65-73 C.O.C. Oko , E.O. Diemuodeke, N.F. Omunakwe, and E. Nnamdi     Development of Formaldehyde Adsorption using Modified Activated Carbon – A Review 75-80 W.D.P Rengga , M. Sudibandriyo and M. Nasikin     Process Optimization for Ethyl Ester Production in Fixed Bed Reactor Using Calcium Oxide Impregnated Palm Shell Activated Carbon (CaO/PSAC 81-86 A. Buasri , B. Ksapabutr, M. Panapoy and N. Chaiyut     Wind Resource Assessment in Abadan Airport in Iran 87-97 Mojtaba Nedaei       The Energy Processing by Power Electronics and its Impact on Power Quality 99-105 J. E. Rocha and B. W. D. C. Sanchez       First Aspect of Conventional Power System Assessment for High Wind Power Plants Penetration 107-113 A. Merzic , M. Music, and M. Rascic   Experimental Study on the Production of Karanja Oil Methyl Ester and Its Effect on Diesel Engine 115-122 N. Shrivastava,  , S.N. Varma and M. Pandey  

  20. Electroweak and flavor physics: Implications for the SSC. Second annual SSCL spring conference

    International Nuclear Information System (INIS)

    1991-01-01

    This book is a collection of vugraphs for the papers given at the conference. The following topics are covered: neutrino physics and dark matter; solar neutrinos; kaon decays; future prospects in high energy physics (non SSC); bottom quark physics; status and physics aims of SSC; and SSC possibilities for B physics

  1. Evaluation of total soluble solids content (TSSC and endogenous pH in antimicrobials of pediatric use

    Directory of Open Access Journals (Sweden)

    Alessandro Leite Cavalcanti

    2013-01-01

    Full Text Available Background: The use of liquid pharmaceutical preparations is a daily occurrence for some children. Evidences show a significant relation between the intake of oral sucrose based medicines and an increase incidence in dental caries. Aim: This in vitro experimental study evaluated the Total Soluble Solids Content (TSSC by means of Brix scale refractometry and the endogenous pH of antimicrobials of pediatric use presented as oral suspensions. Materials and Methods: Nine medications (6 chemotherapics and 3 antibiotics were evaluated by random experiment with 3 repetitions for each sample. The analysis of TSSC readings were performed by Brix refractometry using the Abbé refractometer, and the pH values were determined by potentiometry. Results: The mean TSS contents ranged from 11.73 (Keflaxina to 63.83 (Azitromed. The minimum and maximum mean pH values were 4.12 (Keflaxina and 10.97 (Zitroneo, respectively. Conclusions: The chemotherapic antimicrobials evaluated in this study presented the highest TSSC means, while the antibiotics showed pHs below the values considered as critical, which may contribute to the development of caries lesions in case of inadequate administration of these medications to children.

  2. Increase of content and bioactivity of total phenolic compounds from spent coffee grounds through solid state fermentation by Bacillus clausii.

    Science.gov (United States)

    Rochín-Medina, Jesús J; Ramírez, Karina; Rangel-Peraza, Jesús G; Bustos-Terrones, Yaneth A

    2018-03-01

    Spent coffee grounds are waste material generated during coffee beverage preparation. This by-product disposal causes a negative environmental impact, in addition to the loss of a rich source of nutrients and bioactive compounds. A rotating central composition design was used to determine the optimal conditions for the bioactivity of phenolic compounds obtained after the solid state fermentation of spent coffee grounds by Bacillus clausii . To achieve this, temperature and fermentation time were varied according to the experimental design and the total phenolic and flavonoid content, antioxidant activity and antimicrobial activity were determined. Surface response methodology showed that optimum bioprocessing conditions were a temperature of 37 °C and a fermentation time of 39 h. Under these conditions, total phenolic and flavonoid contents increased by 36 and 13%, respectively, in fermented extracts as compared to non-fermented. In addition, the antioxidant activity was increased by 15% and higher antimicrobial activity was observed against Gram positive and negative bacteria. These data demonstrated that bioprocessing optimization of spent coffee grounds using the surface response methodology was an important tool to improve phenolic extraction, which could be used as an antioxidant and antimicrobial agents incorporated into different types of food products.

  3. The SSC and speculations on the future of proton machines

    International Nuclear Information System (INIS)

    Tigner, M.

    1987-01-01

    In the U.S. a high energy physics community exists, in concert with many expert coleagues abroad, have submitted to the U.S. DOE, extensive documentation about the conceptual design, status of the R and D, and cost estimates for the SSC. Those documents come to more well over 2,000 pages and are available to anyone who would like to read them. This group is reviewed extensively by the DOE and all the expert committees that can possibly be put together and they have all concurred that the SSC is technically feasible, that the hardware is essentially in hand, and the cost has been properly calculated. That having been completed, the community withdraws into the inner sanctum to take counsel amongst themselves and decide whether or not to put the findings in the FY1988 budget. The next signal is when the President submits his budget in late January of 1988

  4. Preliminary study of magnet design for an SSC

    International Nuclear Information System (INIS)

    Taylor, C.E.; Meuser, R.B.

    1983-08-01

    The overriding design consideration for the SSC magnets is that cost of the facility be minimized; at 8 T, approximately 40 km of bending magnets is required for each ring of a 20 TeV collider. We present some results of a parametric study of two-in-one, iron-core magnets for an SSC. These results are necessarily preliminary in nature, and are intended only to show some of the trade-offs for a wide range of the variables. We show also some results for a reference design that produces 6.5 T in the aperture at 4.4 K for a coil inside diameter of 40 mm. It is not to be inferred that we have established this to be an optimum in any sense

  5. Overview of the physics issues at the SSC

    International Nuclear Information System (INIS)

    Hinchliffe, I.

    1984-11-01

    This report presents an overview of physics issues at the SSC. It discusses the progress made at the DPF Summer Study on the Design and Utilization of the SSC and emphasizes the important problems which remain. The discussion of the physics issues is divided into Standard Model, by which is meant the combination of QCD and the Weinberg-Salam model, and Non-Standard Physics, which includes supersymmetry, technicolor, new gauge bosons, compositeness and all the more or less speculative ideas in which theorists like to indulge. Then the work on identification of final states which contain W's, Z's or heavy quarks is discussed, and the impact of this work on some proposed signals for new physics is considered. Finally, some of the areas in which more work is required are discussed. 110 references

  6. Subcooler assembly for SSC single magnet test program

    International Nuclear Information System (INIS)

    Wu, K.C.; Brown, D.P.; Sondericker, J.H.; Farah, Y.; Zantopp, D.; Nicoletti, A.

    1991-01-01

    A subcooler assembly has been designed, constructed and installed in the MAGCOOL magnet test area at Brookhaven National Laboratory. Since July 1989, it has been used for testing SSC magnets. This subcooler assembly and cryogenic system are the first of its kind ever built. Today, with more than 5000 hours of operating time, the subcooler has proved to be a reliable unit with individual components meeting design expectations. The lowest temperatures achieved with one SSC dipole are 3.0 K at the suction of the cold vacuum pump and 3.2 K at the return of the magnet. The system performs well in both steady state operation and during magnet quench, subcooling, cooldown and warmup. 4 refs., 7 figs

  7. Use of learning programs for SSC trigger strategy studies

    International Nuclear Information System (INIS)

    Clearwater, S.H.; Cleland, W.E.; Stern, E.G.

    1990-01-01

    In a novel application of the learning program RL, we are studying ways to develop the trigger for experiments at the SSC. Our initial study, which is still in progress, is to understand how to select top events from background, combining both cuts at the trigger level and in the off-line analysis. Our plan is to carry out these studies for a variety of reactions and thereby build up a comprehensive view of the trigger requirements for a calorimeter-based experiment at the SSC. Our initial results have shown that the learning program can find correlations and cuts that would be quite difficult to find using traditional methods. The program is expected to obtain cuts that are at least as good, if not better, than the the cuts found by traditional methods

  8. Electrical performance characteristics of the SSC Accelerator System String Test

    International Nuclear Information System (INIS)

    Robinson, W.; Burgett, W.; Dombeck, T.; Gannon, J.; Kraushaar, P.; McInturff, A.; Savord, T.; Tool, G.

    1993-05-01

    The string test facility was constructed to provide a development test bed for the arc regions of the Superconducting Super Collider (SSC). Significant effort has been devoted to the development and testing of superconducting magnets, spools, and accelerator control systems required for the SSC. The string test facility provides the necessary environment required to evaluate the operational performance of these components as they are configured as an accelerator lens in the collider. This discussion will review the results of high current testing of the string conducted to evaluate magnet element uniformity and compatibility, the splice resistance used to connect the magnets, and system response to various quench conditions. Performance results of the spools, energy bypass systems, energy dump, and the power supply system are also discussed

  9. Observations on LEP with a view to SSC

    International Nuclear Information System (INIS)

    Toohig, T.E.

    1984-01-01

    From 24-29 October 1984 a visit was made to the LEP project at CERN with a view to extracting from the LEP planning and experience what might be useful in planning an SSC. With a circumference of 26.7 km, in a reasonably densely-populated area outside the boundaries of the CERN site, LEP already faces most of the problems of environment, public relations, maintenance and operation that will be faced by an SSC project. Information is presented under the headings of: (1) radiation protection; (2) heating, ventilation, and airconditioning; (3) electrical power distribution; (4) LEP experiments/UA1, UA2; (5) civil; (6) infrastructure installation; (7) survey; (8) safety; and (9) LEP controls. Each report lists the CERN individuals who generously provided their insights and help

  10. Electrical performance characteristics of the SSC Accelerator System String Test

    International Nuclear Information System (INIS)

    Robinson, W.; Burgett, W.; Dombeck, T.; Gannon, J.; Kraushaar, P.; McInturff, A.; Savord, T.; Tool, G.

    1993-01-01

    The string test facility was constructed to provide a development test bed for the arc regions of the Superconducting Super Collider (SSC). Significant effort has been devoted to the development and testing of superconducting magnets, spools, and accelerator control systems required for the SSC. The string test facility provides the necessary environment required to evaluate the operational performance of these components as they are configured as an accelerator lens in the collider. This discussion will review the results of high current testing of the string conducted to evaluate magnet element uniformity and compatibility, the splice resistance used to connect the magnets, and system response to various quench conditions. Performance results of the spools, energy bypass systems, energy dump, and the power supply system are also discussed

  11. An automated coil winding machine for the SSC dipole magnets

    International Nuclear Information System (INIS)

    Kamiya, S.; Iwase, T.; Inoue, I.; Fukui, I.; Ishida, K.; Kashiwagi, S.; Sato, Y.; Yoshihara, T.; Yamamoto, S.; Johnson, E.; Gibson, C.

    1990-01-01

    The authors have finished the preliminary design of a fully automated coil winding machine that can be used to manufacture the large number of SSC dipole magnets. The machine aims to perform all coil winding operations including coil parts inserting without human operators at a high productive rate. The machine is composed of five industrial robots. In order to verify the design, they built a small winding machine using an industrial robot and successfully wound a 1 meter long coil using SSC dipole magnet wire. The basic design for the full length coil and the robot winding technique are described in this paper. A fully automated coil winding machine using standard industrial components would be very useful if duplicate production lines are used. 5 figs., 1 tab

  12. Development of pixel detectors for SSC vertex tracking

    International Nuclear Information System (INIS)

    Kramer, G.; Shapiro, S.L.; Arens, J.F.; Jernigan, J.G.; Skubic, P.

    1991-04-01

    A description of hybrid PIN diode arrays and a readout architecture for their use as a vertex detector in the SSC environment is presented. Test results obtained with arrays having 256 x 256 pixels, each 30 μm square, are also presented. The development of a custom readout for the SSC will be discussed, which supports a mechanism for time stamping hit pixels, storing their xy coordinates, and storing the analog information within the pixel. The peripheral logic located on the array, permits the selection of those pixels containing interesting data and their coordinates to be selectively read out. This same logic also resolves ambiguous pixel ghost locations and controls the pixel neighbor read out necessary to achieve high spatial resolution. The thermal design of the vertex tracker and the proposed signal processing architecture will also be discussed. 5 refs., 13 figs., 3 tabs

  13. Real time control of the SSC string magnets

    International Nuclear Information System (INIS)

    Calvo, O.; Flora, R.; MacPherson, M.

    1987-01-01

    The system described in this paper, called SECAR, was designed to control the excitation of a test string of magnets for the proposed Superconducting Super Collider (SSC) and will be used to upgrade the present Tevatron Excitation, Control and Regulation (TECAR) hardware and software. It resides in a VME orate and is controlled by a 68020/68881 based CPU running the application software under a real time operating system named VRTX

  14. Irradiation of fiber optics in the SSC tunnel

    International Nuclear Information System (INIS)

    Dickey, C.E.

    1990-03-01

    The salient question is not whether optical fiber will survive in the Super Conducting Supercollider (SSC) tunnel, but rather how long will it survive. Current estimates indicate that single mode fiber under ideal conditions will have an expected lifetime of at least 25 years. Future development of optical fiber will lead to longer service lifetimes and increased radiation hardness. But conservatively speaking, current production optical fibers can probably not be depended upon for more than 25 years of service even under ideal conditions

  15. SSC 40 mm cable results and 50 mm design discussions

    International Nuclear Information System (INIS)

    Christopherson, D.; Capone, D.; Hannaford, R.; Remsbottom, R.; Delashmit, R.; Jayakumar, R.J.; Snitchler, G.; Scanlan, R.; Royet, J.

    1991-01-01

    This paper presents a summary of the cable produced for the 1990 40 mm Dipole Program. The cable design parameters for the 50 mm Dipole Program are discussed, as well as portions of the SSC specification draft. Considerations leading to the final cable configuration and the results of preliminary trials are included. The first iteration of a strand mapping program to automate cable strand maps is introduced

  16. SSC 40 mm cable results and 50 mm design discussions

    International Nuclear Information System (INIS)

    Christopherson, D.; Capone, D.; Hannaford, R.; Remsbottom, R.; Jayakumar, R.; Snitchler, G.; Scanlan, R.; Royet, J.

    1990-09-01

    A summary of the cable produced for the 1990 40 mm Dipole Program is presented. The cable design parameters for the 50 mm Dipole Program are discussed, as well as portions of the SSC specification draft. Considerations leading to the final cable configuration and the results of preliminary trials are included. The first iteration of a strand mapping program to automate cable strand maps is introduced. 7 refs., 2 figs., 1 tab

  17. Wire scanner data analysis for the SSC Linac emittance measurement

    International Nuclear Information System (INIS)

    Yao, C.Y.; Hurd, J.W.; Sage, J.

    1993-07-01

    The wire scanners are designed in the SSC Linac for measurement of beam emittance at various locations. In order to obtain beam parameters from the scan signal, a data analysis program was developed that considers the problems of noise reduction, machine modeling, parameter fitting, and correction. This program is intended as a tool for Linac commissioning and also as part of the Linac control program. Some of the results from commissioning runs are presented

  18. Effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco

    OpenAIRE

    Makan, Abdelhadi; Assobhei, Omar; Mountadar, Mohammed

    2013-01-01

    Abstract This study aimed to evaluate the effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco in terms of internal temperature, produced gases quantity, organic matter conversion rate, and the quality of the final composts. For this purpose, in-vessel bioreactor was designed and used to evaluate both appropriate initial air pressure and appropriate initial moisture content for the composting process. Moreove...

  19. An update on passive correctors for the SSC dipole magnets

    International Nuclear Information System (INIS)

    Green, M.A.

    1991-05-01

    The concept of correction of the magnetization sextupole became a topic of discussion as soon as it was realized that superconductor magnetization could have a serious effect on the SSC beam during injection. Several methods of correction were proposed. These included (1) correction with active bore tube windings like those on the HERA machine which correct out magnetization sextupole and the sextupole due to iron saturation, (2) correction with persistent sextupole windings mounted on the bore tube (3) correction using passive superconductor (4) correction using ferromagnetic material, and (5) correction using oriented magnetized materials. This report deals with the use of passive superconductor to correct the magnetization sextupole. Two basic methods are explored in this report: (1) One can correct the magnetization sextupole by changing the diameter of the superconductor filaments in one or more blocks of the SSC dipole. (2) One can correct the magnetization sextupole and decapole by mounting passive superconducting wires on the inside of the SSC dipole coil bore. In addition, an assessment of the contribution of each conductor in the dipole to the magnetization sextupole and decapole is shown. 38 refs, 25 figs., 15 tabs

  20. Comparisons of processes and performance of SSC-VQP material

    International Nuclear Information System (INIS)

    Seuntjens, J.M.; Clark, F.Y.; Erdmann, M.J.; Coleman, E.S.; Jones, B.A.

    1994-01-01

    The Superconducting Super Collider's (SSC) cable Vendor Qualification Program (VQP) will end in FY 1993. At the time of this writing, all 8 vendors involved in this program have demonstrated capability to fabricate conductor which meets SSC specifications. The magnet vendors have hard choices to make in calendar year 1993 in deciding which cable vendors will make the production cable. It is well accepted that because of requirements of magnet uniformity, that only one vendor will be chosen for dipole Inner cable, one vendor for dipole Outer cable, and one vendor for quadrupole Outer cable. The production quantities are nominally 500, 500, and 200 metric tonnes, respectively. Among the many deciding factors are a technically sound production process, process control, and production quantity capability of each cable vendor. Qualified vendors will have proven their technical process and process control is adequate for production quantities. This paper is part of ongoing effort to provide technical information for the magnet vendor's decision making process. Some of the Phase IB process data is summarized as well as results of a portion of the materials characterization performed at the SSC Laboratory. Key process and final product parameters for each cable vendor are compared without identifying specific vendor's process detail

  1. Comparisons of processes and performance of SSC-VQP material

    International Nuclear Information System (INIS)

    Seuntjens, J.; Clark, F.; Erdmann, M.; Coleman, E.; Jones, B.

    1993-05-01

    The Superconducting Super Collider's (SSC) cable Vendor Qualification Program (VQP) will end in FY 1993. At the time of this writing, all 8 vendors involved in this program have demonstrated capability to fabricate conductor which meets SSC specifications. The magnet vendors have hard choices to make in calendar year 1993 in deciding which cable vendors will make the production cable. It is well accepted that because of requirements of magnet uniformity, that only one vendor will be chosen for dipole Inner cable, one vendor for dipole Outer cable, and one vendor for quadrupole Outer cable. The production quantities are nominally 500, 500, and 200 metric tonnes, respectively. Among the many deciding factors are a technically sound production process, process control, and production quantity capability of each cable vendor. Qualified vendors will have proven their technical process and process control is adequate for production quantities. This paper is part of ongoing effort to provide technical information for the magnet vendor's decision making process. Some of the Phase IB process data is summarized and well as results of a portion of the materials characterization performed at the SSC Laboratory. Key process and final product parameters for each cable vendor are compared without identifying specific vendor's process detail

  2. Evaluating advanced LMR [liquid metal reactor] reactivity feedbacks using SSC

    International Nuclear Information System (INIS)

    Slovik, G.C.; Van Tuyle, G.J.; Kennett, R.J.; Cheng, H.S.

    1988-01-01

    Analyses of the PRISM and SAFR Liquid Metal Reactors with SSC are discussed from a safety and licensing perspective. The PRISM and SAFR reactors with metal fuel are designed for inherent shutdown responses to loss-of-flow and loss-of-heat-sink events. The demonstration of this technology was performed by EBR-II during experiments in April 1986 by ANL (Planchon, et al.). Response to postulated TOPs (control rod withdrawal) are made acceptable largely by reducing reactivity swings, and therefore minimizing the size of possible ractivity insertions. Analyses by DOE and the contractors GE, RI, and ANL take credit for several reactivity feedback mechanisms during transient calculations. These feedbacks include Doppler, sodium density, and thermal expansion of the grid plates, the load pads, the fuel (axial) and the control rod which are now factored into the BNL SSC analyses. The bowing feedback mechanism is not presently modeled in the SSC due to its complexity and subsequent large uncertainty. The analysis is conservative by not taking credit for this negative feedback mechanism. Comparisons of BNL predictions with DOE contractors are provided

  3. Development of Radhard VLSI electronics for SSC calorimeters

    International Nuclear Information System (INIS)

    Dawson, J.W.; Nodulman, L.J.

    1989-01-01

    A new program of development of integrated electronics for liquid argon calorimeters in the SSC detector environment is being started at Argonne National Laboratory. Scientists from Brookhaven National Laboratory and Vanderbilt University together with an industrial participants are expected to collaborate in this work. Interaction rates, segmentation, and the radiation environment dictate that front-end electronics of SSC calorimeters must be implemented in the form of highly integrated, radhard, analog, low noise, VLSI custom monolithic devices. Important considerations are power dissipation, choice of functions integrated on the front-end chips, and cabling requirements. An extensive level of expertise in radhard electronics exists within the industrial community, and a primary objective of this work is to bring that expertise to bear on the problems of SSC detector design. Radiation hardness measurements and requirements as well as calorimeter design will be primarily the responsibility of Argonne scientists and our Brookhaven and Vanderbilt colleagues. Radhard VLSI design and fabrication will be primarily the industrial participant's responsibility. The rapid-cycling synchrotron at Argonne will be used for radiation damage studies involving response to neutrons and charged particles, while damage from gammas will be investigated at Brookhaven. 10 refs., 6 figs., 2 tabs

  4. Enhanced treatment efficiency of an anaerobic sequencing batch reactor (ASBR) for cassava stillage with high solids content.

    Science.gov (United States)

    Luo, Gang; Xie, Li; Zhou, Qi

    2009-06-01

    Cassava stillage is a high strength organic wastewater with high suspended solids (SS) content. The efficiency of cassava stillage treatment using an anaerobic sequencing batch reactor (ASBR) was significantly enhanced by discharging settled sludge to maintain a lower sludge concentration (about 30 g/L) in the reactor. Three hydraulic retention times (HRTs), namely 10 d, 7.5 d, 5 d, were evaluated at this condition. The study demonstrated that at an HRT of 5 d and an organic loading rate (OLR) of 11.3 kg COD/(m(3) d), the total chemical oxygen demand (TCOD) and soluble COD (SCOD) removal efficiency can still be maintained at above 80%. The settleability of digested cassava stillage was improved significantly, and thus only a small amount of settled sludge needed to be discharged to maintain the sludge concentration in the reactor. Furthermore, the performance of ASBR operated at low and high sludge concentration (about 79.5 g/L without sludge discharged) was evaluated at an HRT of 5 d. The TCOD removal efficiency and SS in the effluent were 61% and 21.9 g/L respectively at high sludge concentration, while the values were 85.1% and 2.4 g/L at low sludge concentration. Therefore, low sludge concentration is recommended for ASBR treating cassava stillage at an HRT 5 d due to lower TCOD and SS in the effluent, which could facilitate post-treatment.

  5. Physico-chemical properties of Brazilian cocoa butter and industrial blends. Part I Chemical composition, solid fat content and consistency

    Directory of Open Access Journals (Sweden)

    Ribeiro, A. P. B.

    2012-03-01

    Full Text Available A comparative study of the primary properties of six cocoa butter samples, representative of industrial blends and cocoa butter extracted from fruits cultivated in different geographical areas in Brazil is presented. The samples were evaluated according to fatty acid composition, triacylglycerol composition, regiospecific distribution, melting point, solid fat content and consistency. The results allowed for differentiating the samples according to their chemical compositions, thermal resistance properties, hardness characteristics, as well as technological adequacies and potential use in regions with tropical climates.

    En este trabajo se presenta un estudio comparativo de las propiedades primarias de mantecas de cacao, representativas de las mezclas industriales, y de la manteca de cacao original de diferentes zonas geográficas de Brasil. Las muestras fueron evaluadas de acuerdo a la composición de ácidos grasos, composición de triglicéridos, distribución de los ácidos grasos en las moléculas de triglicéridos, punto de fusión, contenido de grasa sólida y consistencia. Los resultados permitieron diferenciar las muestras por su composición química, propiedades de resistencia térmica, características de dureza, así como en materia de adecuaciones tecnológicas y los usos potenciales en las regiones de clima tropical.

  6. Dry anaerobic digestion of food waste and cardboard at different substrate loads, solid contents and co-digestion proportions.

    Science.gov (United States)

    Capson-Tojo, Gabriel; Trably, Eric; Rouez, Maxime; Crest, Marion; Steyer, Jean-Philippe; Delgenès, Jean-Philippe; Escudié, Renaud

    2017-06-01

    The increasing food waste production calls for developing efficient technologies for its treatment. Anaerobic processes provide an effective waste valorization. The influence of the initial substrate load on the performance of batch dry anaerobic co-digestion reactors treating food waste and cardboard was investigated. The load was varied by modifying the substrate to inoculum ratio (S/X), the total solids content and the co-digestion proportions. The results showed that the S/X was a crucial parameter. Within the tested values (0.25, 1 and 4gVS·gVS -1 ), only the reactors working at 0.25 produced methane. Methanosarcina was the main archaea, indicating its importance for efficient methanogenesis. Acidogenic fermentation was predominant at higher S/X, producing hydrogen and other metabolites. Higher substrate conversions (≤48%) and hydrogen yields (≤62mL·gVS -1 ) were achieved at low loads. This study suggests that different value-added compounds can be produced in dry conditions, with the initial substrate load as easy-to-control operational parameter. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Eco-geochemical peculiarities of mercury content in solid residue of snow in the industrial enterprises impacted areas of Tomsk

    Science.gov (United States)

    Filimonenko, E. A.; Lyapina, E. E.; Talovskaya, A. V.; Parygina, I. A.

    2014-11-01

    Snow, as short-term consignation Wednesday, has several properties that lead to its widespread use in ecologicalgeochemical and geological research. By studying the chemical composition of the dust fallout you can indirectly assess the condition of atmospheric air.1-2. Determining the content of mercury in snow cover, you can define its contribution for the longest period of the year in our region, with the most intensive use of various types of fuel (coal, gas, firewood), that puts a strain on urban ecosystems in terms of ecology.3-4. In addition, snow cleans the atmosphere of mercury, but it accumulates in the snow, and during the spring melting of snow hits the ground and rivers, polluting them. Part of the mercury back into the atmosphere. It should also be note the special nature of the circulation of air masses over the city in winter, creating a heat CAP, which contributes to air pollution of the city. 5-6-7. The high load areas of industrial impact were detected during the eco-geochemical investigations of mercury load index in the impacted areas of enterprises of Tomsk. It was found out, that aerosol particles of industrial emissions in Tomsk contain mercury. The contamination transfer character of mercury sources and occurrence modes of pollutants in snow solid residue were detected during the researches of industrial impact.

  8. The effect of moisture content on solid-state anaerobic digestion of dairy manure from a sawdust-bedded pack barn

    Science.gov (United States)

    The effect of moisture content on solid-state anaerobic digestion of dairy manure from a Korean sawdust-bedded pack barn was determined using laboratory-scale digesters operated at three moisture levels (70, 76, and 83% on a wet basis) at 37 C for 85 days. Results showed that digesters containing m...

  9. Radiation damage testing at the SSC [Superconducting Super Collider

    International Nuclear Information System (INIS)

    Chinowsky, W.; Thun, R.

    1990-06-01

    A Task Force on Radiation Damage Testing met at the SSC Laboratory on March 5--6, 1990. This Task Force was asked to assess the availability of appropriate facilities for radiation damage tests of SSC detector materials and components. The Task Force was also instructed to review the techniques and standards for conducting such tests. Semiconductors were considered separately from other detector materials. Radiation damage test of electronic devices generally require exposures to both ionizing radiation and neutrons, whereas non-electric components such as plastic scintillating materials, adhesives, cable insulation, and other organic polymers are adequately tested with ionizing radiation only. Test standards are discussed with respect to irradiation techniques, environmental factors, dosimetry, and mechanisms whereby various materials are damaged. It is emphasized that radiation sources should be chosen to duplicate as much as possible the expected SSC environment and that the effects from ionizing particles and from neutrons be investigated separately. Radiation damage tests at reactors must be designed with particular care complex spectra of neutrons and gamma rays are produced at such facilities. It is also essential to investigate dose-rate effects since they are known to be important in many cases. The required irradiations may last several months and are most easily carried out with dedicated radioactive sources. Environmental factors such as the presence of oxygen when testing plastic scintillators, or temperature when measuring semiconductor annealing effects, must also be taken into account. The importance of reliable dosimetry is stressed and suitable references cited. Finally, it is noted that an understanding of the mechanisms for radiation damage in semiconductor and other materials is important in planning irradiations and evaluating results

  10. Overview and status of beam instrumentation at the SSC

    International Nuclear Information System (INIS)

    Webber, R.C.

    1993-05-01

    An overview of beam instrumentation requirements at the SSC and a status report on work progress is given. Small transverse emittance beams, ranging in energy from 30 KeV to 20 TeV, must be commissioned, measured, and diagnosed. Instrumentation plans and current design and development efforts for BPMs and other systems are presented. Monitors and electronics soon to be delivered for use in the Linac are described. Design of the Linac systems has been done with requirements and applications in the synchrotron in mind and thus should provide a basis for design of much of that hardware. The useful commonality of design across the machines is discussed

  11. Conductor development for the Superconducting Super Collider (SSC)

    International Nuclear Information System (INIS)

    Gregory, E.

    1988-01-01

    This review investigates the developments in fine filamentary materials over the last three years and traces how the relations between the magnet requirements and property improvements have fashioned SSC conductor specifications. The review emphasizes factors that affect filament nonuniformity and the overall quality of the product. The elimination of proximity effect-induced coupling in SCC type conductors, by introducing small percentages of manganese into the copper between the filaments, is discussed. Modification of a Fermi kit has produced materials with improved critical current densities. The possibility of using this approach to make conductors for accelerator magnets is assessed

  12. Measurement of AC electrical characteristics of SSC superconducting dipole magnets

    International Nuclear Information System (INIS)

    Smedley, K.M.; Shafer, R.E.

    1992-01-01

    Experiments were conducted to measure the AC electrical characteristics of SSC superconducting dipole magnets over the frequency range of 0.1 Hz to 10 kHz. A magnet equivalent circuit representing the magnet DC inductance, eddy current losses, coil-to-ground and turn-to-turn capacitance, was synthesized from the experimental data. This magnet equivalent circuit can be used to predict the current ripple distribution along the superconducting magnet string and can provide dynamic information for the design of the collider current regulation loop

  13. High P/sub T/ detectors for the SSC

    International Nuclear Information System (INIS)

    Trilling, G.H.

    1987-11-01

    Summarized in this report is some of the work done at the recent Workshop on Experiments, Detectors, and Experimental Areas for the Supercollider held at Berkeley. The major goal was to develop an understanding of what complement of detectors would provide the capability for a well-balanced physics program at the SSC. Unlike earlier studies which had emphasized individual components such as tracking, calorimetry, etc., the intention was to focus on complete detectors. The particular detectors discussed in this paper are: the large solenoid detectors, the compact solenoid detectors, the non-magnetic detectors, the dipole detectors and muon detectors. 10 refs., 6 figs., 2 tabs

  14. A super fixed target beauty experiment at the SSC

    International Nuclear Information System (INIS)

    Spiegel, L.; Murphy, C.T.; Cox, B.; Arenton, M.; Conetti, S.; Corti, G.; Dukes, C.; Golovatyuk, V.; Lawry, T.; McManus, A.

    1993-01-01

    The observation and precision measurement of CP violation asymmetries and the phase of the CKM matrix is a major objective of B experiments at the SSC. The yields of reconstructed and tagged B decays and the various factors which minimize the dilution factors make measurements of CP asymmetries in the fixed target option known as the SFT more than competitive with much more expensive hadron collider experiments and significantly better than asymmetric e + e - B factories. Moreover, the superior time resolution possible in the SFT configuration allows a precision in the measurement of the CKM matrix element phases possible with the SFT option for various B decay modes

  15. Hadron identification in a fixed target experiment at the SSC

    International Nuclear Information System (INIS)

    Nelson, K.S.; Cox, B.

    1993-01-01

    This article presents the design criteria and expected performance of a hadron identification system in a fixed target experiment at the SSC. The proposed SFT spectrometer will be used as a model for the discussion. Two primary uses of hadron identification is a B physics experiment are flavor tagging and the rejection of background due to particle reflections in the reconstruction of exclusive decay modes. In the first case it is shown that use of kaons can increase substantially the number of events which can be tagged. In the latter case, decays in which particles are mis-identified can form a background to a desired decay mode

  16. Design features of the SSC [Superconducting Super Collider] dipole magnet

    International Nuclear Information System (INIS)

    Willen, E.; Cottingham, J.; Ganetis, G.

    1989-01-01

    The main ring dipole for the SSC is specified as a high performance magnet that is required to provide a uniform, 6.6 T field in a 4 cm aperture at minimum cost. These design requirements have been addressed in an R ampersand D program in which the coil design, coil mechanical support, yoke and shell structure, trim coil and beam tube design, and a variety of new instrumentation, have been developed. The design of the magnet resulting from this intensive R ampersand D program, including various measurements from both 1.8 m and 17 m long models, is reviewed. 7 refs., 3 figs

  17. SSC [Superconducting Super Collider] dipole coil production tooling

    International Nuclear Information System (INIS)

    Carson, J.A.; Barczak, E.J.; Bossert, R.C.; Brandt, J.S.; Smith, G.A.

    1989-03-01

    Superconducting Super Collider dipole coils must be produced to high precision to ensure uniform prestress and even conductor distribution within the collared coil assembly. Tooling is being prepared at Fermilab for the production of high precision 1M and 16.6M SSC dipole coils suitable for mass production. The design and construction methods builds on the Tevatron tooling and production experience. Details of the design and construction methods and measured coil uniformity of 1M coils will be presented. 4 refs., 10 figs

  18. Debunching and Capture in the LEB for the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Mahale, N.; Furman, M.

    1991-05-01

    The authors present the details of the capture process in the Low Energy Booster (LEB) for the SSC. They consider only the longitudinal dynamics. Space charge forces are computed quasistatically. The beam pipe is considered to be perfectly conducting. With respect to maximizing the capture efficiency and minimizing the space charge tune spread, initial few milliseconds are very important. They present only the first few milliseconds of the cycle, during which space charge effects are significant. For the numerical simulation they use the code ESME.

  19. Beam diagnostic system for SSC on HIRFL central console

    International Nuclear Information System (INIS)

    Zhang Guixu; Wang Zhen; Huang Tuanhua

    1998-01-01

    The SSC ion beam diagnostic system on the console of HIRFL in institute of modern physics is presented. The information between console and diagnostic system can be transferred via DECnet communication. The central computer for HIRFL console is VAX-8350, the working computer of diagnostic system is changed from IBM PC/XT to COMPAQ 486, and the operating program is rewritten from FORTRAN to C. In order to communicate information, DECnet TTT function is put into both programs on the VAX and PC

  20. Initial results from 50mm short SSC dipoles at Fermilab

    International Nuclear Information System (INIS)

    Bossert, R.C.; Brandt, J.S.; Carson, J.A.; Coulter, K.; Delchamps, S.; Ewald, K.D.; Fulton, H.; Gonczy, I.; Gourlay, S.A.; Jaffery, T.S.; Kinney, W.; Koska, W.; Lamm, M.J.; Strait, J.B.; Wake, M.; Gordon, M.; Hassan, N.; Sims, R.; Winters, M.

    1991-03-01

    Several short model SSC 50 mm bore dipoles are being built and tested at Fermilab. Mechanical design of these magnets has been determined from experience involved in the construction and testing of 40 mm dipoles. Construction experience includes coil winding, curing and measuring, coil end part design and fabrication, ground insulation, instrumentation, collaring and yoke assembly. Fabrication techniques are explained and construction problems are discussed. Similarities and differences from the 40 mm dipole tooling and management components are outlined. Test results from the first models are presented. 19 refs., 12 figs

  1. Effect of Initial Moisture Content on the in-Vessel Composting Under Air Pressure of Organic Fraction of MunicipalSolid Waste in Morocco

    Directory of Open Access Journals (Sweden)

    Abdelhadi Makan

    2013-01-01

    Full Text Available This study aimed to evaluate the effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco in terms of internal temperature, produced gases quantity, organic matter conversion rate, and the quality of the final composts.For this purpose, in-vessel bioreactor was designed and used to evaluate both appropriate initial air pressure and appropriate initial moisture content for the composting process. Moreover, 5 experiments were carried out within initial moisture content of 55%, 65%, 70%, 75% and 85%. The initial air pressure and the initial moisture content of the mixture showed a significant effect on the aerobic composting. The experimental results demonstrated that for composting organic waste, relatively high moisture contents are better at achieving higher temperatures and retaining them for longer times.This study suggested that an initial moisture content of around 75%, under 0.6 bar, can be considered as being suitable for efficient composting of organic fraction of municipal solid waste. These last conditions, allowed maximum value of temperature and final composting product with good physicochemical properties as well as higher organic matter degradation and higher gas production. Moreover, final compost obtained showed good maturity levels and can be used for agricultural applications.

  2. Effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco.

    Science.gov (United States)

    Makan, Abdelhadi; Assobhei, Omar; Mountadar, Mohammed

    2013-01-03

    This study aimed to evaluate the effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco in terms of internal temperature, produced gases quantity, organic matter conversion rate, and the quality of the final composts.For this purpose, in-vessel bioreactor was designed and used to evaluate both appropriate initial air pressure and appropriate initial moisture content for the composting process. Moreover, 5 experiments were carried out within initial moisture content of 55%, 65%, 70%, 75% and 85%. The initial air pressure and the initial moisture content of the mixture showed a significant effect on the aerobic composting. The experimental results demonstrated that for composting organic waste, relatively high moisture contents are better at achieving higher temperatures and retaining them for longer times.This study suggested that an initial moisture content of around 75%, under 0.6 bar, can be considered as being suitable for efficient composting of organic fraction of municipal solid waste. These last conditions, allowed maximum value of temperature and final composting product with good physicochemical properties as well as higher organic matter degradation and higher gas production. Moreover, final compost obtained showed good maturity levels and can be used for agricultural applications.

  3. Effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco

    Directory of Open Access Journals (Sweden)

    Mountadar Mohammed

    2013-01-01

    Full Text Available Abstract This study aimed to evaluate the effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco in terms of internal temperature, produced gases quantity, organic matter conversion rate, and the quality of the final composts. For this purpose, in-vessel bioreactor was designed and used to evaluate both appropriate initial air pressure and appropriate initial moisture content for the composting process. Moreover, 5 experiments were carried out within initial moisture content of 55%, 65%, 70%, 75% and 85%. The initial air pressure and the initial moisture content of the mixture showed a significant effect on the aerobic composting. The experimental results demonstrated that for composting organic waste, relatively high moisture contents are better at achieving higher temperatures and retaining them for longer times. This study suggested that an initial moisture content of around 75%, under 0.6 bar, can be considered as being suitable for efficient composting of organic fraction of municipal solid waste. These last conditions, allowed maximum value of temperature and final composting product with good physicochemical properties as well as higher organic matter degradation and higher gas production. Moreover, final compost obtained showed good maturity levels and can be used for agricultural applications.

  4. Conclusions from the engineering subgroup of the SSC liquid argon calorimeter working group

    International Nuclear Information System (INIS)

    Bederede, D.; Cooper, W.; Mulholland, G.; Kroon, P.; Guryn, W.; Lobkowicz, F.; Mason, I.; Pohlen, J.; Schindler, R.H.; Scholle, E.A.; Watanabe, Y.; Watt, R.

    1990-01-01

    The SSC Calorimeter Workshop was organized to explore the feasibility of each calorimeter technology for use in a 4π detector at the SSC. The Liquid Argon Calorimeter group further subdivided into four subgroups; Hermeticity, Engineering, Module Details, and Electronics. This is the report of the Engineering Subgroup whose charge was to evaluate the cost, schedule, manpower, safety, and facilities requirements for the construction of a large liquid argon calorimeter for the SSC

  5. A helium venting model for a SSC half cell

    International Nuclear Information System (INIS)

    Carcagno, R.H.; McAshan, M.S.; Schiesser, W.E.

    1991-01-01

    When a Superconducting Super Collider (SSC) dipole magnet quenches, the quench protection system will intentionally quench other magnets in the half cell. The result is that the stored energy of all of these quenched magnets will be absorbed equally among them. These simultaneous quenches produce heat, which diffuses from the magnet coils to the main helium (He) coolant channels and thereby eventually causes an increase in the He pressure. When the quench is detected, vent valves open to minimize the He pressure increase and thus prevent damage to the magnets. The performance of the He venting system has been modeled and simulated to establish whether the venting will take place as required. The model consists of partial differential equation energy balances written radially for the magnet coils, collar, and yoke; and ordinary differential equations of energy and mass balance written for the He in the magnets and relief header. The basic algorithm is the numerical method of lines, with finite difference approximation of the spatial derivatives, and time integration by LSODES. Simulation results are presented for an SSC half cell of the Accelerator Systems String Test (ASST) facility. The results are also compared with recent string quench measurements performed at the Fermilab String Test Facility

  6. Report of the workshop on realistic SSC lattices

    International Nuclear Information System (INIS)

    1985-10-01

    A workshop was held at the SSC Central Design Group from May 29 to June 4, 1985, on topics relating to the lattice of the SSC. The workshop marked a shift of emphasis from the investigation of simplified test lattices to the development of a realistic lattice suitable for the conceptual design report. The first day of the workshop was taken up by reviews of accelerator system requirements, of the reference design solutions for these requirements, of lattice work following the reference design, and of plans for the workshop. The work was divided among four working groups. The first, chaired by David Douglas, concerned the arcs of regular cells. The second group, which studied the utility insertions, was chaired by Beat Leemann. The third group, under David E. Johnson, concerned itself with the experimental insertions, dispersion suppressors, and phase trombones. The fourth group, responsible for global lattice considerations and the design of a new realistic lattice example, was led by Ernest Courant. The papers resulting from this workshop are roughly divided into three sets: those relating to specific lattice components, to complete lattices, and to other topics. Among the salient accomplishments of the workshop were additions to and optimization of lattice components, especially those relating to lattices using 1-in-1 magnets, either horizontally or vertically separated, and the design of complete lattice examples. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

  7. Parallel processing at the SSC: The fact and the fiction

    International Nuclear Information System (INIS)

    Bourianoff, G.; Cole, B.

    1991-10-01

    Accurately modelling the behavior of particles circulating in accelerators is a computationally demanding task. The particle tracking code currently in use at SSC is based upon a ''thin element'' analysis (TEAPOT). In this model each magnet in the lattice is described by a thin element at which the particle experiences an impulsive kick. Each kick requires approximately 200 floating point operations (''FLOP''). For the SSC collider lattice consisting of 10 4 elements, performing a tracking of study for a set of 100 particles for 10 7 turns would require 2 x 10 15 FLOPS. Even on a machine capable of 100 MFLOP/sec (MFLOPS), this would require 2 x 10 7 seconds, and many such runs are necessary. It should be noted that the accuracy with which the kicks are to be calculated is important: the large number of iterations involved will magnify the effects of small errors. The inability of current computational resources to effectively perform the full calculation motivates the migration of this calculation to the most powerful computers available. A survey of the current research into new technologies for superconducting reveals that the supercomputers of the future will be parallel in nature. Further, numerous such machines exist today, and are being used to solve other difficult problems. Thus it seems clear that it is not early to begin developing the capability to develop tracking codes for parallel architectures. This report discusses implementing parallel processing on the SCC

  8. The effect of solid content on silylated-γ-AI2O3/PVDF-HFP-coated PE separators for lithium secondary battery

    International Nuclear Information System (INIS)

    Im, Jong Su; Sohn, Joon Yong; Shin, Jun Hwa; Nho, Young Chang; Kim, Jeong Soo

    2009-01-01

    Several PVDF-HFP/silylated γ-AI 2 O 3 -coated PE (polyethylene) separators with various solidities (various compositions of PVDF-HFP/silylated γ-AI 2 O 3 ) were prepared by a dip-coating of PE separators in PVDF-HFP/silylated γ-AI 2 O 3 /acetone mixtures. FT-IR spectroscopy was used to confirm the chemical reactions between silane coupling agent and γ-AI 2 O 3 . The SEM images of the coated separators showed that various morphologies could be produced by changing the composition of total contents of binder and solid contents. The effects of composition in inorganic material (silane coupling agent-treated γ-AI 2 O 3 ) and binder (PVDF-HFP) on the physio-chemical properties of the prepared separators such as liquid electrolyte uptake, and ion conductivity were investigated and reported in this paper

  9. Effects of Degree of Enzymatic Interesterification on the Physical Properties of Margarine Fats: Solid Fat Content, Crystallization Behavior, Crystal Morphology, and Crystal Network

    DEFF Research Database (Denmark)

    Zhang, Hong; Smith, Paul; Adler-Nissen, Jens

    2004-01-01

    In this study enzymatic-interesterified margarine fats with different conversion degrees were produced in a packed-bed reactor. The effects of conversion degree on the formation of free fatty acids and diacyglycerols, solid fat content, crystallization behavior, microstructure, and crystal network...... °C with increasing conversion degree. Increased conversion degree from the blend to products, measured by X-ray with addition of 50% of rapeseed oil for dilution, caused the content of â to decrease from 100% to 33%, and 30% and eventually to pure ⢠crystal. However, double chain packing...

  10. Solid nanofoams based on cellulose nanofibers and indomethacin-the effect of processing parameters and drug content on material structure

    DEFF Research Database (Denmark)

    Bannow, J; Benjamins, J-W; Wohlert, J

    2017-01-01

    to verify the wet-foam stability at different pHs. The pH influenced the amount of solubilized drug and the processing-window was very narrow at high drug loadings. The results were compared to real foaming-experiments and solid state analysis of the final cellular solids. The parameters were assembled...... into a processing chart, highlighting the importance of the right combination of processing parameters (pH and time-point of pH adjustment) in order to successfully prepare cellular solid materials with up to 46 wt% drug loading....

  11. The effect of treating plum tree with Rovral (iprodion and Euparen (dichlofluanid on the content of soluble solids in fruit

    Directory of Open Access Journals (Sweden)

    Halina Borecka

    2013-12-01

    Full Text Available The concentration of soluble solids in plum fruit varied and depended on the cultivar, year, and fungicide treatment. Plums from trees treated with Rovral (iprodion contained in some case the lowest level of soluble solids, higher or equal levels were found in those sprayed with Euparen (dichlofluanid, and the highest concentration of soluble solids was in fruits from untreated trees. Explanation of this phenomenon is possible by looking for changes in photosynthesis of treated and untreated leaves. Fungicide treatment of some plum cultivars, particularly with Rovral, decreased the photosynthesis of the leaves.

  12. Current Approaches to the Treatment of Systemic-Sclerosis-Associated Pulmonary Arterial Hypertension (SSc-PAH).

    Science.gov (United States)

    Sobanski, Vincent; Launay, David; Hachulla, Eric; Humbert, Marc

    2016-02-01

    Pulmonary arterial hypertension (PAH) is a severe condition causing significant morbidity and mortality in patients with systemic sclerosis (SSc). Despite the use of specific treatments, SSc-PAH survival remains poorer than in idiopathic PAH (IPAH). Recent therapeutic advances in PAH show a lower magnitude of response in SSc-PAH and a higher risk of adverse events, as compared to IPAH. The multifaceted underlying mechanisms and the multisystem nature of SSc probably explain part of the worse outcomes in SSc-PAH compared to IPAH. This review describes the current management of SSc-PAH with an emphasis on the impact of the different organ involvements in the prognosis and treatment response. An earlier detection of PAH and a better characterization of the clinical phenotypes of SSc-PAH are warranted in clinical practice and future trials. Determinants of prognosis, surrogate markers of clinical improvement or worsening, and relevance of the common endpoints used in clinical trials should be evaluated in this specific population. A multidisciplinary approach in expert referral centers is mandatory for SSc-PAH management.

  13. Is transverse feedback necessary for the SSC emittance preservation? (Vibration noise analysis and feedback parameters optimization)

    International Nuclear Information System (INIS)

    Parkhomchuk, V.V.; Shiltsev, V.D.

    1993-06-01

    The paper considers the Superconducting Super Collider (SSC) site ground motion measurements as well as data from accelerators worldwide about noises that worsen beam performance. Unacceptably fast emittance growth due to these noises is predicted for the SSC. A transverse feedback system was found to be the only satisfactory alternative to prevent emittance decay. Optimization of the primary feedback parameters was done

  14. Modeling and Predicting the Electrical Conductivity of Composite Cathode for Solid Oxide Fuel Cell by Using Support Vector Regression

    Science.gov (United States)

    Tang, J. L.; Cai, C. Z.; Xiao, T. T.; Huang, S. J.

    2012-07-01

    The electrical conductivity of solid oxide fuel cell (SOFC) cathode is one of the most important indices affecting the efficiency of SOFC. In order to improve the performance of fuel cell system, it is advantageous to have accurate model with which one can predict the electrical conductivity. In this paper, a model utilizing support vector regression (SVR) approach combined with particle swarm optimization (PSO) algorithm for its parameter optimization was established to modeling and predicting the electrical conductivity of Ba0.5Sr0.5Co0.8Fe0.2 O3-δ-xSm0.5Sr0.5CoO3-δ (BSCF-xSSC) composite cathode under two influence factors, including operating temperature (T) and SSC content (x) in BSCF-xSSC composite cathode. The leave-one-out cross validation (LOOCV) test result by SVR strongly supports that the generalization ability of SVR model is high enough. The absolute percentage error (APE) of 27 samples does not exceed 0.05%. The mean absolute percentage error (MAPE) of all 30 samples is only 0.09% and the correlation coefficient (R2) as high as 0.999. This investigation suggests that the hybrid PSO-SVR approach may be not only a promising and practical methodology to simulate the properties of fuel cell system, but also a powerful tool to be used for optimal designing or controlling the operating process of a SOFC system.

  15. Variable-field permanent-magnet quadrupole for the SSC

    International Nuclear Information System (INIS)

    Barlow, D.B.; Kraus, R.H. Jr.; Martinez, R.P.; Meyer, R.E.

    1994-01-01

    A set of compact variable-field permanent-magnet quadrupoles have been designed, fabricated, and tested for use in the SSC linac matching section. The quadrupoles have 24 mm-diameter apertures and 40 mm-long poles. The hybrid (permanent-magnet and iron) design, uses a fixed core of magnet material (NdFeB) and iron (C-1006) surrounded by a rotating ring of the same magnet material and iron. The quadrupole gradient-length product can be smoothly varied from a minimum of 0.7 T up to a maximum of 4.3 T by a 90 degree rotation of the outer ring of iron and magnet material

  16. Application of multiple timestep integration method in SSC

    International Nuclear Information System (INIS)

    Guppy, J.G.

    1979-01-01

    The thermohydraulic transient simulation of an entire LMFBR system is, by its very nature, complex. Physically, the entire plant consists of many subsystems which are coupled by various processes and/or components. The characteristic integration timesteps for these processes/components can vary over a wide range. To improve computing efficiency, a multiple timestep scheme (MTS) approach has been used in the development of the Super System Code (SSC). In this paper: (1) the partitioning of the system and the timestep control are described, and (2) results are presented showing a savings in computer running time using the MTS of as much as five times the time required using a single timestep scheme

  17. A medical facility proposal to use the SSC linac

    International Nuclear Information System (INIS)

    Funk, L.W.

    1994-01-01

    A consortium organized by the Texas National Research Laboratory Commission under a Department of Energy grant proposes to build and operate a Regional Medical Technology Center to function as a combined medical radioisotope production complex and proton cancer therapy facility using the Linear Accelerator (Linac) assets of the Superconducting Super Collider (SSC). The radioisotope production complex will serve as a domestic source of radioisotopes critically needed by the U.S. pharmaceutical industry and nuclear medicine facilities throughout North America. Presently, more than 70 percent of radioisotopes used in U.S. nuclear medicine procedures are produced outside the country. The Center's state-of-the-art proton cancer therapy facility will serve the Central United States, providing advanced capabilities and augmenting facilities in California and Massachusetts. Long-term, it is anticipated that the RMTC also will stimulate nuclear medicine research, advance medical diagnostic technologies, and generate new industrial applications for linear accelerator technology

  18. A medical facility proposal to use the SSC linac

    International Nuclear Information System (INIS)

    Funk, L.W.

    1995-01-01

    A consortium organized by the Texas National Research Laboratory Commission (TNRLC) under a Department of Energy (DOE) grant proposes to build and operate a Regional Medical Technology Center (RMTC) to function as a combined medical radioisotope production complex and proton cancer therapy facility using the linear accelerator (linac) assets of the cancelled Superconducting Super Collider (SSC). The radioisotope production complex will serve as a domestic source of radioisotopes critically needed by the U.S. pharmaceutical industry and nuclear medicine facilities throughout North America. Presently, more than 70 percent of radioisotopes used in U.S. nuclear medicine procedures are produced outside the country. The Center's state-of-the-art proton cancer therapy facility will serve the Central United States, providing advanced capabilities and augmenting facilities in California and Massachusetts. Long-term, it is anticipated that the RMTC also will stimulate nuclear medicine research, advance medical diagnostic technologies, and generate new industrial applications of linear accelerator technology. (orig.)

  19. A medical facility proposal to use the SSC linac

    Science.gov (United States)

    Warren Funk, L.

    1995-05-01

    A consortium organized by the Texas National Research Laboratory Commission (TNRLC) under a Department of Energy (DOE) grant proposes to build and operate a Regional Medical Technology Center (RMTC) to function as a combined medical radioisotope production complex and proton cancer therapy facility using the linear accelerator (linac) assets of the cancelled Superconducting Super Collider (SSC). The radioisotope production complex will serve as a domestic source of radioisotopes critically needed by the U.S. pharmaceutical industry and nuclear medicine facilities throughout North America. Presently, more than 70 percent of radioisotopes used in U.S. nuclear medicine procedures are produced outside the country. The Center's state-of-the-art proton cancer therapy facility will serve the Central United States, providing advanced capabilities and augmenting facilities in California and Massachusetts. Long-term, it is anticipated that the RMTC also will stimulate nuclear medicine research, advance medical diagnostic technologies, and generate new industrial applications of linear accelerator technology.

  20. Performance of field measuring probes for SSC magnets

    International Nuclear Information System (INIS)

    Thomas, R.; Ganetis, G.; Herrera, J.; Hogue, R.; Jain, A.; Louie, W.; Marone, A.; Wanderer, P.

    1994-01-01

    Several years of experience have been acquired on the operation of probes (open-quotes molesclose quotes) constructed for the measurement of the multipole components of the magnetic fields of SSC magnets. The field is measured by rotating coils contained in a 2.4-m long tube that is pulled through the aperture of the magnet by an external device - the transporter. In addition to the measuring coils, the tube contains motors for rotating the coil and a system for sensing local vertical using gravity sensors to provide an absolute reference for the field measurements. The authors describe the steps that must be taken in order to ensure accurate, repeatable measurements; the design changes that have been motivated by difficulties encountered (noise, vibration, variations in temperature); and other performance issues. The mechanical interface between the probe and the beam tube of the magnet is also described

  1. Performance of field measuring probes for SSC magnets

    International Nuclear Information System (INIS)

    Thomas, R.; Ganetis, G.; Herrera, J.; Hogue, R.; Jain, A.; Louie, W.; Marone, A.; Wanderer, P.

    1993-01-01

    Several years of experience have been acquired on the operation of probes (''moles'') constructed for the measurement of the multipole components of the magnetic fields of SSC magnets. The field is measured by rotating coils contained in a 2.4-m long tube that is pulled through the aperture of the magnet by an external device-the transporter. In addition to the measuring coils, the tube contains motors for rotating the coil and a system for sensing local vertical using gravity sensors to provide an absolute reference for the field measurements. We describe the steps that must be taken in order to ensure accurate, repeatable measurements; the design changes that have been motivated by difficulties encountered (noise, vibration, variations in temperature); and other performance issues. The mechanical interface between the probe and the hewn tube of the magnet is also described

  2. Overview and status of RF systems for the SSC Linac

    International Nuclear Information System (INIS)

    Mynk, J.; Grippe, J.; Cutler, R.I.; Rodriguez, R.

    1993-05-01

    The Superconducting Super Collider (SSC) Linear Accelerator (Linac) produces a 600-MeV, 35-μs, H-beam at a 10-Hz repetition rate. The beam is accelerated by a series of RF cavities. These consist of a Radio Frequency Quadrupole (RFQ), two bunchers, and four Drift Tube Linac (DTL) tanks at 427.617 MHz, and two bunchers, nine side-coupled Linac modules, and an energy compressor at 1282.851 MHz. The RFQ amplifier and the low-frequency buncher cavity amplifiers use gridded tubes, while the other cavities use klystron amplifier systems. The RF control system consists of a reference line and cavity feedback and feedforward loops for each amplifier. The RF amplifier system for each of these accelerator cavities is described, and the current status of each system is presented

  3. Simulation of quenches in SSC magnets with passive quench protection

    International Nuclear Information System (INIS)

    Koepke, K.

    1985-06-01

    The relative ease of protecting an SSC magnet following a quench and the implications of quench protection on magnet reliability and operation are necessary inputs in a rational magnet selection process. As it appears likely that the magnet selection will be made prior to full scale prototype testing, an alternative means is required to ascertain the surviveability of contending magnet types. This paper attempts to provide a basis for magnet selection by calculating the peak expected quench temperatures in the 3 T Design C magnet and the 6 T Design D magnet as a function of magnet length. A passive, ''cold diode'' protection system has been assumed. The relative merits of passive versus active protection systems have been discussed in a previous report. It is therefore assumed that - given the experience gained from the Tevatron system - that an active quench protection system can be employed to protect the magnets in the eventuality of unreliable cold diode function

  4. Collider Physics: SDC/SSC liquified fiber calorimetry

    International Nuclear Information System (INIS)

    White, J.T.; Huson, F.R.

    1992-01-01

    Most effort was directed toward the D-Zero experiment at Fermilab. Over 3 pb -1 of high-quality physics data have been obtained. Analysis of the results (wino-zino physics, squark physics), D-zero data acquisition systems efforts, and level-1 and level-2 trigger work are described. Other work concerned detector development for use at the SSC. This technology consists of using liquid scintillator-filled tubes as scintillating fibers for a ''calorimeter.'' The key issues were to demonstrate that the liquid fibers were sufficiently rad-hard and to demonstrate that fibers with sufficiently long attenuation length could be found to satisfy the resolution requirements; both constraints could be satisfied

  5. Rad-hard electronics study for SSC detectors

    International Nuclear Information System (INIS)

    Ekenberg, T.; Dawson, J.; Stevens, A.; Haberichter, W.

    1991-01-01

    The radiation environment in a SSC detector operating at a luminosity of 10 33 cm -2 s -1 will put stringent requirements on radiation hardness of the electronics. Over the expected 10 year life-time of a large detector, ionizing radiation doses of up to 20 MRad and neutron fluences of 10 16 neutrons/cm 2 are projected. At a luminosity of 10 34 cm -2 s -1 even higher total doses are expected. the effect of this environment have been simulated by exposing CMOS/bulk and CMOS/SOS devices from monolithic processes to neutrons and ionizing radiation. leakage currents, noise variations, and DC characteristics have been measured before and after exposure in order to evaluate the effects of the irradiations. As expected the device characteristics remained virtually unchanged by neutron irradiation, while ionizing radiation caused moderate degradation of performance. 5 refs., 6 figs

  6. A novel bridge coupler for SSC coupled cavity linac

    International Nuclear Information System (INIS)

    Yao, C.G.; Chang, C.R.; Funk, W.

    1992-01-01

    A novel magnetically coupled multi-cavity bridge coupler is proposed for SSC Coupled-Cavity-Linac (CCL). The bridge coupler is a five cell disc-loaded waveguide with a small central aperture used for measurement and two large curved coupling slots near the edge on each disc. The two coupling slots on the adjacent disc are rotated 90 degrees in orientation to reduce the direct coupling. This type of structure is capable of producing very large coupling (>10% in our longest bridge coupler). Also because of the small opening on the discs, the high-order-modes are very far (> 300 MHz) above the operating mode. Thus for long bridge couplers, the magnetic coupled structure should provide maximum coupling with minimum mode mixing problems. In this paper both physics and engineering issues of this new bridge coupler are presented. (Author) 5 refs., 2 tabs., 6 figs

  7. Variable-field permanent magnet quadrupole for the SSC

    International Nuclear Information System (INIS)

    Barlow, D.B.; Kraus, R.H. Jr.; Martinez, R.P.; Meyer, R.E.

    1993-01-01

    A set of compact variable-field permanent-magnet quadrupoles have been designed, fabricated, and tested for use In the SSC linac matching section. The quadrupoles have 24 mm-diameter apertures and 40 mm-long poles. The hybrid (permanent-magnet and iron) design, uses a fixed core of magnet material (NdFeB) and iron (C-1006) surrounded by a rotating ring of the same magnet material and iron. The quadrupole gradient-length product can be smoothly varied from a minimum of 0.7 T up to a maximum, of 4.3 T by a 90 degrees rotation of the outer ring of iron and magnet material

  8. New technique for wiring SSC superconducting sextupole corrector coils

    International Nuclear Information System (INIS)

    Leon, B.

    1985-01-01

    There exists in the electronics industry, a technology for the manufacture of printed circuit (PC) boards which is directly transferable into the creation of highly controlled coils, such as the SSC sextupole superconducting corrector coils. This technology, which uses a process of laying down insulated wire in highly controlled patterns has heretofore been confined exclusively to the manufacture of high density printed circuit (PC) boards, possibly due to an ignorance of its utility in the field of precision winding of coils. This ability to fix wires in a well defined location can be used to produce precision wound coils in a very cost-effective manner. These coils may be superior in quality to conventionally made coils. Before describing what can be created with this technology, it is necessary to take a look at this coil winding process, the MULTIWIRE process, and the industry which has utilized this technology

  9. A new technique for wiring SSC superconducting sextupole corrector coils

    International Nuclear Information System (INIS)

    Leon, B.

    1985-01-01

    There exists in the electronics industry, a technology for the manufacture of printed circuit (PC) boards which is directly transferable into the creation of highly controlled coils, such as the SSC sextupole superconducting corrector coils. This technology, which uses a process of laying down insulated wire in highly controlled patterns, has heretofore been confined excusively to the manufacture of high density printed circuit (PC) boards, possibly due to an ignorance of its utility in the field of precision winding of coils. This ability to fix wires in a well defined location can be used to produce precision wound coils in a very cost-effective manner. These coils may be superior in quality to conventionally made coils. Before describing what can be created with this technology, it is necessary to take a look at this coil winding process, the MULTIWIRE process, and the industry which has utilized this technology

  10. Coil and iron design for SSC 50 mm magnet

    International Nuclear Information System (INIS)

    Gupta, R.C.; Kahn, S.A.; Morgan, G.H.

    1990-01-01

    In this paper we present the design of the two dimensional coil and iron cross section, referred to as DSX201/W6733, for the 50 mm aperture dipole magnet being built at the Brookhaven National Laboratory for the Superconducting Super Collider (SSC). The computed values of the allowed field harmonics as a function of current, the quench performance predictions, the stored energy calculations, the effect of random errors on the coil placement and the Lorentz forces on the coil will be presented. The yoke has been optimized to reduce iron saturation effects on the field harmonics. We shall present the summary of this design which will include the expected overall performance of this cross section. 4 refs., 8 figs., 12 tabs

  11. Winding mandrel design for the wide cable SSC dipole

    International Nuclear Information System (INIS)

    Morgan, G.H.; Greene, A.; Jochen, G.; Morgillo, A.

    1990-01-01

    The 50 mm coil i.d. SSC dipole magnets use wider cables to give a greater operational margin between quench field and operating field. The cable used for the inner coil has 30 strands of the same size (0.808 mm) instead of 23 and the outer has 36 strands of the same size (0.648 mm) instead of 30 and the cable widths are increased in proportion. Although the coil inner diameter has been increased from 40 mm, the coil ends are noticeably harder to wind. This report describes the computational and experimental effort to design winding mandrels or center posts for the constant-perimeter ends. 1 ref., 2 figs., 2 tabs

  12. A development environment for the SSC control system

    International Nuclear Information System (INIS)

    Murray, Doug; Martinsen, Garth; Wang, Judy

    1994-01-01

    The SSC is developing a design environment for control system development within the context of EPICS. The environment is aimed at developers of applications using the EPICS Input/Output Controller (IOC). The unique aspect of this effort is our emphasis on providing a simple and intuitive development environment compared with tools currently available. Our most important goal in this effort has been to hide the complexity of EPICS IOC development from the developers. This paper describes two tools which are under development; The Function Block Editor (FBE) and the State Machine Editor (SME). The FBE provides a visual editing environment for graphically describing control processes as a set of related functional blocks. The configuration of functional blocks is then translated into IOC records and executed. SME allows the user to visually construct a sequence using a notation we are modeling after Grafcet [1]. State machines are translated into EPICS State Notation Language programs and executed. Future extensions will be described. ((orig.))

  13. Improvement of Medium Chain Fatty Acid Content and Antimicrobial Activity of Coconut Oil via Solid-State Fermentation Using a Malaysian Geotrichum candidum

    Directory of Open Access Journals (Sweden)

    Anahita Khoramnia

    2013-01-01

    Full Text Available Coconut oil is a rich source of beneficial medium chain fatty acids (MCFAs particularly lauric acid. In this study, the oil was modified into a value-added product using direct modification of substrate through fermentation (DIMOSFER method. A coconut-based and coconut-oil-added solid-state cultivation using a Malaysian lipolytic Geotrichum candidum was used to convert the coconut oil into MCFAs-rich oil. Chemical characteristics of the modified coconut oils (MCOs considering total medium chain glyceride esters were compared to those of the normal coconut oil using ELSD-RP-HPLC. Optimum amount of coconut oil hydrolysis was achieved at 29% moisture content and 10.14% oil content after 9 days of incubation, where the quantitative amounts of the modified coconut oil and MCFA were 0.330 mL/g of solid media (76.5% bioconversion and 0.175 mL/g of solid media (53% of the MCO, respectively. MCOs demonstrated improved antibacterial activity mostly due to the presence of free lauric acid. The highest MCFAs-rich coconut oil revealed as much as 90% and 80% antibacterial activities against Staphylococcus aureus and Escherichia coli, respectively. The results of the study showed that DIMOSFER by a local lipolytic G. candidum can be used to produce MCFAs as natural, effective, and safe antimicrobial agent. The produced MCOs and MCFAs could be further applied in food and pharmaceutical industries.

  14. Improvement of medium chain fatty acid content and antimicrobial activity of coconut oil via solid-state fermentation using a Malaysian Geotrichum candidum.

    Science.gov (United States)

    Khoramnia, Anahita; Ebrahimpour, Afshin; Ghanbari, Raheleh; Ajdari, Zahra; Lai, Oi-Ming

    2013-01-01

    Coconut oil is a rich source of beneficial medium chain fatty acids (MCFAs) particularly lauric acid. In this study, the oil was modified into a value-added product using direct modification of substrate through fermentation (DIMOSFER) method. A coconut-based and coconut-oil-added solid-state cultivation using a Malaysian lipolytic Geotrichum candidum was used to convert the coconut oil into MCFAs-rich oil. Chemical characteristics of the modified coconut oils (MCOs) considering total medium chain glyceride esters were compared to those of the normal coconut oil using ELSD-RP-HPLC. Optimum amount of coconut oil hydrolysis was achieved at 29% moisture content and 10.14% oil content after 9 days of incubation, where the quantitative amounts of the modified coconut oil and MCFA were 0.330 mL/g of solid media (76.5% bioconversion) and 0.175 mL/g of solid media (53% of the MCO), respectively. MCOs demonstrated improved antibacterial activity mostly due to the presence of free lauric acid. The highest MCFAs-rich coconut oil revealed as much as 90% and 80% antibacterial activities against Staphylococcus aureus and Escherichia coli, respectively. The results of the study showed that DIMOSFER by a local lipolytic G. candidum can be used to produce MCFAs as natural, effective, and safe antimicrobial agent. The produced MCOs and MCFAs could be further applied in food and pharmaceutical industries.

  15. Effect of W content in solid solution on properties and microstructure of (Ti,W)C-Ni{sub 3}Al cermets

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Bin; Xiong, Weihao, E-mail: whxiong@hust.edu.cn; Zhang, Man; Jing, Yong; Li, Baolong; Luo, Haifeng; Wang, Shengqing

    2016-08-15

    (Ti{sub 1-x}W{sub x})C solid solutions (x = 0.05, 0.15, 0.25, 0.35) were synthesized by carbothermal reduction and then were used as hard phases to prepare (Ti,W)C-Ni{sub 3}Al cermets by vacuum sintering. (Ti,W)C-Ni{sub 3}Al cermets showed weak core-rim structure carbide particles embedded in Ni{sub 3}Al binder. As W content in (Ti,W)C increased, core-rim structure of carbide particles got weaker and the contrast of particles lowered down in SEM-BSE morphologies. Furthermore, the densification of cermets was promoted with W content in solid solution increasing, meanwhile TRS and toughness of cermets were improved obviously. In this paper, the wettability of molten metal on different group transition metal carbides was discussed in detail based on valence-electron configurations (VECs) of carbides. - Highlights: • (Ti{sub 1-x}W{sub x})C solid solutions were synthesized by carbothermal reduction. • (Ti,W)C-Ni{sub 3}Al cermets were prepared through powder metallurgy route. • The increase of W can improve wetting and densification significantly. • (Ti,W)C-Ni{sub 3}Al cermets showed a weak core-rim structure particles embedded in binder. • Wetting behavior were discussed from valence-electron configurations of carbides.

  16. Genome Wide Association Studies (GWAS Identify QTL on SSC2 and SSC17 Affecting Loin Peak Shear Force in Crossbred Commercial Pigs.

    Directory of Open Access Journals (Sweden)

    Chunyan Zhang

    Full Text Available Of all the meat quality traits, tenderness is considered the most important with regard to eating quality and market value. In this study we have utilised genome wide association studies (GWAS for peak shear force (PSF of loin muscle as a measure of tenderness for 1,976 crossbred commercial pigs, genotyped for 42,721 informative SNPs using the Illumina PorcineSNP60 Beadchip. Four 1 Mb genomic regions, three on SSC2 (at 4 Mb, 5 Mb and 109 Mb and one on SSC17 (at 20 Mb, were detected which collectively explained about 15.30% and 3.07% of the total genetic and phenotypic variance for PSF respectively. Markers ASGA0008566, ASGA0008695, DRGA0003285 and ASGA0075615 in the four regions were strongly associated with the effects. Analysis of the reference genome sequence in the region with the most important SNPs for SSC2_5 identified FRMD8, SLC25A45 and LTBP3 as potential candidate genes for meat tenderness on the basis of functional annotation of these genes. The region SSC2_109 was close to a previously reported candidate gene CAST; however, the very weak LD between DRGA0003285 (the best marker representing region SSC2_109 and CAST indicated the potential for additional genes which are distinct from, or interact with, CAST to affect meat tenderness. Limited information of known genes in regions SSC2_109 and SSC17_20 restricts further analysis. Re-sequencing of these regions for informative animals may help to resolve the molecular architecture and identify new candidate genes and causative mutations affecting this trait. These findings contribute significantly to our knowledge of the genomic regions affecting pork shear force and will potentially lead to new insights into the molecular mechanisms regulating meat tenderness.

  17. A pilot-scale steam autoclave system for treating municipal solid waste for recovery of renewable organic content: Operational results and energy usage.

    Science.gov (United States)

    Holtman, Kevin M; Bozzi, David V; Franqui-Villanueva, Diana; Offeman, Richard D; Orts, William J

    2016-05-01

    A pilot-scale (1800 kg per batch capacity) autoclave used in this study reduces municipal solid waste to a debris contaminated pulp product that is efficiently separated into its renewable organic content and non-renewable organic content fractions using a rotary trommel screen. The renewable organic content can be recovered at nearly 90% efficiency and the trommel rejects are also much easier to sort for recovery. This study provides the evaluation of autoclave operation, including mass and energy balances for the purpose of integration into organic diversion systems. Several methods of cooking municipal solid waste were explored from indirect oil heating only, a combination of oil and direct steam during the same cooking cycle, and steam only. Gross energy requirements averaged 1290 kJ kg(-1) material in vessel, including the weight of free water and steam added during heating. On average, steam recovery can recoup 43% of the water added and 30% of the energy, supplying on average 40% of steam requirements for the next cook. Steam recycle from one vessel to the next can reduce gross energy requirements to an average of 790 kJ kg(-1). © The Author(s) 2016.

  18. Numerical and experimental studies on effects of moisture content on combustion characteristics of simulated municipal solid wastes in a fixed bed

    International Nuclear Information System (INIS)

    Sun, Rui; Ismail, Tamer M.; Ren, Xiaohan; Abd El-Salam, M.

    2015-01-01

    Highlights: • The effects of moisture content on the burning process of MSW are investigated. • A two-dimensional mathematical model was built to simulate the combustion process. • Temperature distributions, process rates, gas species were measured and simulated. • The The conversion ratio of C/CO and N/NO in MSW are inverse to moisture content. - Abstract: In order to reveal the features of the combustion process in the porous bed of a waste incinerator, a two-dimensional unsteady state model and experimental study were employed to investigate the combustion process in a fixed bed of municipal solid waste (MSW) on the combustion process in a fixed bed reactor. Conservation equations of the waste bed were implemented to describe the incineration process. The gas phase turbulence was modeled using the k–ε turbulent model and the particle phase was modeled using the kinetic theory of granular flow. The rate of moisture evaporation, devolatilization rate, and char burnout was calculated according to the waste property characters. The simulation results were then compared with experimental data for different moisture content of MSW, which shows that the incineration process of waste in the fixed bed is reasonably simulated. The simulation results of solid temperature, gas species and process rate in the bed are accordant with experimental data. Due to the high moisture content of fuel, moisture evaporation consumes a vast amount of heat, and the evaporation takes up most of the combustion time (about 2/3 of the whole combustion process). The whole bed combustion process reduces greatly as MSW moisture content increases. The experimental and simulation results provide direction for design and optimization of the fixed bed of MSW

  19. Numerical and experimental studies on effects of moisture content on combustion characteristics of simulated municipal solid wastes in a fixed bed

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Rui, E-mail: Sunsr@hit.edu.cn [School of Energy Science and Engineering, Harbin Institute of Technology, 92, West Dazhi Street, Harbin 150001 (China); Ismail, Tamer M., E-mail: temoil@aucegypt.edu [Department of Mechanical Engineering, Suez Canal University, Ismailia (Egypt); Ren, Xiaohan [School of Energy Science and Engineering, Harbin Institute of Technology, 92, West Dazhi Street, Harbin 150001 (China); Abd El-Salam, M. [Department of Basic Science, Cairo University, Giza (Egypt)

    2015-05-15

    Highlights: • The effects of moisture content on the burning process of MSW are investigated. • A two-dimensional mathematical model was built to simulate the combustion process. • Temperature distributions, process rates, gas species were measured and simulated. • The The conversion ratio of C/CO and N/NO in MSW are inverse to moisture content. - Abstract: In order to reveal the features of the combustion process in the porous bed of a waste incinerator, a two-dimensional unsteady state model and experimental study were employed to investigate the combustion process in a fixed bed of municipal solid waste (MSW) on the combustion process in a fixed bed reactor. Conservation equations of the waste bed were implemented to describe the incineration process. The gas phase turbulence was modeled using the k–ε turbulent model and the particle phase was modeled using the kinetic theory of granular flow. The rate of moisture evaporation, devolatilization rate, and char burnout was calculated according to the waste property characters. The simulation results were then compared with experimental data for different moisture content of MSW, which shows that the incineration process of waste in the fixed bed is reasonably simulated. The simulation results of solid temperature, gas species and process rate in the bed are accordant with experimental data. Due to the high moisture content of fuel, moisture evaporation consumes a vast amount of heat, and the evaporation takes up most of the combustion time (about 2/3 of the whole combustion process). The whole bed combustion process reduces greatly as MSW moisture content increases. The experimental and simulation results provide direction for design and optimization of the fixed bed of MSW.

  20. Improve biogas production from low-organic-content sludge through high-solids anaerobic co-digestion with food waste.

    Science.gov (United States)

    Liu, Chuanyang; Li, Huan; Zhang, Yuyao; Liu, Can

    2016-11-01

    Anaerobic co-digestion of sewage sludge and food waste was tested at two different total solid (TS) concentrations. In the low-solids group with TS 4.8%, the biogas production increased linearly as the ratio of food waste in substrate increased from 0 to 100%, but no synergetic effect was found between the two substrates. Moreover, the additive food waste resulted in the accumulation of volatile fatty acids and decelerated biogas production. Thus, the blend ratio of food waste should be lower than 50%. While in the high-solids group with TS 14%, the weak alkaline environment with pH 7.5-8.5 avoided excessive acidification but high concentration of free ammonia was a potential risk. However, good synergetic effect was found between the two substrates because the added food waste improved mass transfer in sludge cake. Thus, 50% was recommended as the optimum ratio of food waste in substrate because of the best synergetic effect. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Best practices: Strategic stigma change (SSC): five principles for social marketing campaigns to reduce stigma.

    Science.gov (United States)

    Corrigan, Patrick W

    2011-08-01

    This column describes strategic stigma change (SSC), which comprises five principles and corresponding practices developed as a best practice to erase prejudice and discrimination associated with mental illness and promote affirming behaviors and social inclusion. SSC principles represent more than ten years of insights from the National Consortium on Stigma and Empowerment. The principles, which are centered on consumer contact that is targeted, local, credible, and continuous, were developed to inform the growth of large-scale social marketing campaigns supported by governments and nongovernmental organizations. Future social marketing efforts to address stigma and the need for evidence to determine SSC's penetration and impact are also discussed.

  2. Software sensors for biomass concentration in a SSC process using artificial neural networks and support vector machine.

    Science.gov (United States)

    Acuña, Gonzalo; Ramirez, Cristian; Curilem, Millaray

    2014-01-01

    The lack of sensors for some relevant state variables in fermentation processes can be coped by developing appropriate software sensors. In this work, NARX-ANN, NARMAX-ANN, NARX-SVM and NARMAX-SVM models are compared when acting as software sensors of biomass concentration for a solid substrate cultivation (SSC) process. Results show that NARMAX-SVM outperforms the other models with an SMAPE index under 9 for a 20 % amplitude noise. In addition, NARMAX models perform better than NARX models under the same noise conditions because of their better predictive capabilities as they include prediction errors as inputs. In the case of perturbation of initial conditions of the autoregressive variable, NARX models exhibited better convergence capabilities. This work also confirms that a difficult to measure variable, like biomass concentration, can be estimated on-line from easy to measure variables like CO₂ and O₂ using an adequate software sensor based on computational intelligence techniques.

  3. On levels unconditional declassification of solid materials with very low radioactive content and downloads liquids and gases to the environment

    International Nuclear Information System (INIS)

    2004-01-01

    This guide aims to establish radiological criteria for declassification (waiver) of the radioactive material of radiological regulatory control and levels unconditional clearance for solid materials and the authorized discharge limits for liquids and gases to the environment that meet these criteria for exposure scenarios acceptably conservative. This Guide to radioactive waste from the apply industrial, medical and research, which they will be managed as waste conventional. This guidance excludes from its scope the option of recycling and reuse of materials that have been declassified and wastes arising from activities and practices which naturally occurring radionuclides present are.

  4. Controlling the crossing angle in the SSC [Superconducting Super Collider

    International Nuclear Information System (INIS)

    Garren, A.A.; Johnson, D.E.

    1989-04-01

    The colliding beams in the SSC must cross at a small angle, so that when the bunches pass each other away from the interaction point (IP), they are sufficiently separated to avoid disruptive beam-beam forces. However, the crossing angle is so small that the adjacent quadrupoles must be common to both beams. Only after passing through four common quadrupoles on each side of the IP, are the beams split by vertical dipoles into separate beamlines. In order to make the closed orbits of the two beams cross at a definite angle at the IP (within a range up to 150 μrad), a series of correction dipoles are placed in the insertions. If these dipoles are excited in such a way as to control the closed orbits alone, the dispersion will be mismatched, reaching values of up to 50 cm in the arcs. This mismatch is due to the closed orbit displacements in the interaction region (IR) quadrupoles, causing them to act as bending magnets. Therefore, both the closed orbit and dispersion must be matched simultaneously. Solutions to this problem are presented. 6 figs

  5. SSC collider quadrupole cold mass design and development

    International Nuclear Information System (INIS)

    Farrell, R.A.; Murray, F.S.; Jonas, P.A.; Mischler, W.R.; Blecher, L.

    1992-01-01

    Approximately 1,664 focussing and defocussing superconducting quadrupoles are required for the two SSC collider rings. Collider quadruple magnets (CQMS) must satisfy stringent performance, reliability, life and low cost criteria. Performance requirements include field uniformity, training, quench, tracking, thermal cycling and alignment. The CQM cold mass design presented incorporates lessons IGC and Alsthom Intermagnetics S.A. (AISA), our joint venture with GEC-Alsthom, learned in the design, development and manufacture of 500 MRI, 160 high-field custom and 126 HERA quadruple superconducting magnets. This baseline design reflects careful quantitative assessment of coil winding placement and collar material, evaluation of field uniformity and mechanical performance of the magnet coil ends using 3-D modeling and analysis, and considers tolerance and process variability. Selected CQM cold mass design highlights and a proposed prototype development program that allows incorporation of test feedback into the design to minimize risk are detailed in this paper. This information may be helpful to SSCL in the design and development of prototype CQM'S

  6. Design of the SSC medium-beta Interaction Regions

    International Nuclear Information System (INIS)

    Nosochkov, Y.M.

    1993-06-01

    In the SSC design the 87.12 km long collider lattice consists of two 35.28 km identical arcs located on the North and South sides of the machine and two 8.28 km clusters placed on the West and on the East. Each cluster contains two Interaction Regions (IRs), the Utility section and the interconnect sections between them. According to present plans the goal for the optics in the East IRs is to provide for a high value of the luminosity and, hence, for a low β at the Interaction Point (IP). The West IRs are aimed at providing for a large space for detector which can be achieved at the cost of higher value of the β and lower luminosity. The optics of each IR are based on the same optical configuration which gives an opportunity to use mostly identical quadrupoles and dipoles in four IRs. Trivial modification of the central region in this basic configuration allows for a wide range of values for detector free space from L = 20 m to L = 90 m, suitable for the experiments in both clusters. L denotes here the distance between the IP and the nearest magnetic element of the machine. In this paper we briefly review the current design of the so-called medium-β IR optics with a large free space for detector of L = 90 m, which could be used in the West cluster

  7. Field measuring probe for SSC [Superconducting Super Collider] magnets

    International Nuclear Information System (INIS)

    Ganetis, G.; Herrera, J.; Hogue, R.; Skaritka, J.; Wanderer, P.; Willen, E.

    1987-03-01

    The field probe developed for measuring the field in SSC dipole magnets is an adaptation of the rotating tangential coil system in use at Brookhaven for several years. Also known as the MOLE, it is a self-contained room-temperature mechanism that is pulled through the aperture of the magnet with regular stops to measure the local field. Several minutes are required to measure the field at each point. The probe measures the multipole components of the field as well as the field angle relative to gravity. The sensitivity of the coil and electronics is such that the field up to the full 6.6 T excitation of the magnet as well as the field when warm with only 0.01 T excitation can be measured. Tethers are attached to both ends of the probe to carry electrical connections and to supply dry nitrogen to the air motors that rotate the tangential windings as well as the gravity sensor. A small computer is attached to the probe for control and for data collection, analysis and storage. Digital voltmeters are used to digitize the voltages from the rotating coil and several custom circuits control motor speeds in the probe. The overall diameter of the probe is approximately 2 cm and its length is 2.4 m; the field sensitive windings are 0.6 m in length

  8. Electrical characteristics of long strings of SSC superconducting dipoles

    International Nuclear Information System (INIS)

    Shafer, R.E.; Smedley, K.M.

    1992-01-01

    Because long strings of series-connected superconducting magnets have no dc resistance and low ac losses, the string behaves like a shorted transmission line. The string is thus resonant at multiple half-wavelengths unless damped by the inclusion of resistors that couple to the LdI/dt voltage across the magnet inductance. Based on the measured ac characteristics of individual magnets, it is possible to predict the electrical properties of long strings of magnets for a variety of damping resistors. These strings can be simulated using an analytic representation in FORTRAN (using complex-number notation) or a discrete-component equivalent-circuit modelling program (e.g., SPICE). Various electrical parameters, including characteristic impedance, signal velocity, induced power-supply ripple current, attenuation lengths, and driving-point impedances, can be predicted, and the damping resistor value can be optimized. Comparisons will be made to measurements on a long string of superconducting Tevatron magnets, and some predictions will be made for the SSC collider magnet system

  9. A liquid nitrogen temperature SSC [Superconducting Super Collider

    International Nuclear Information System (INIS)

    McAshan, M.S.; VanderArend, P.

    1987-04-01

    Under the assumption that new developments in the science of superconductivity will lead to dipole magnets suitable for the SSC that have the same properties with regard to field, field quality, size and cost as those in the present conception of the collider, but operating at 77 K rather than 4.35 K; the initial cost of the collider facility is found to be less by $213 M out of the $2,000 M actual construction cost for the collider technical systems and the conventional facilities estimated in the Conceptual Design Report. EDI and contingency is not included in these figures. Operation at the higher temperature is not, however, an unequivocal advantage. The beam line vacuum system in the 77 K case presents problems that will require a larger magnet aperture for satisfactory solution. The costs of this together with the cost of the development and construction of the new vacuum system required is estimated to be $156 M. The net capital cost saving associated with the higher temperature operation is thus found to be $57 M or about 3% of the estimated cost. In addition it is estimated that the operating cost of the facility will under conditions be less by $27.5 M per year in the steady-state including an allowance for the greater availability of the simpler cryogenic system. 14 refs., 1 fig., 4 tabs

  10. A room-temperature liquid calorimeter prototype for the SSC

    International Nuclear Information System (INIS)

    Brandenburg, G.W.; Geer, S.H.; Oliver, J.; Sadowski, E.; Theriot, D.

    1990-01-01

    Calorimeters will be an extremely important part of SSC detectors as they have been in existing collider detectors. The main issues that need to be addressed are: (1) energy resolution of jets and electrons, (2) segmentation, (3) hermiticity, (4) response time, and (5) radiation resistance. An attractive possibility on all these counts is the use of room-temperature liquids together with uranium, as pioneered by UA1. The authors are planning a prototype calorimeter which consists of a sealed vessel containing both the radiator plates and the readout pads. This geometry has been appropriately named the swimming pool design. The general mechanical starting point is similar to the SLD liquid argon calorimeters. The points they wish to address are the following: (1) Simple and reliable modular construction techniques, (2) Satisfactory electrical connections with minimal geometric impact, (3) The necessity of isolating radiator plates and liquid to maintain purity, (4) What materials can be immersed without compromising the liquid purity. The design and construction of the swimming pool electromagnetic calorimeter prototype is being carried out at the Harvard High Energy Physics Laboratory. This is one of the first attempts to build a full-scale prototype of such a design

  11. Automatic beam centering at the SSC interaction regions

    International Nuclear Information System (INIS)

    Joestlein, H.

    1984-01-01

    In the SSC interaction regions, the two colliding beams, each only a few microns in size, will have to be centered and maintained in good alignment over many hours, in order to provide the maximum possible luminosity and to minimize off-center beam-beam focussing effects. It is unlikely that sufficiently good alignment can be achieved without some kind of active feedback system, based on the beam-beam interaction rate. This memo describes such a system. In the proposed scheme, one of the beams is moved continuously and in a circular fashion about its mean transverse position. The radius of this motion is approximately 0.01 of the rms beam size at the interaction point. The motion is achieved with two sets of crossed high frequency dipole magnets, one on each side of the interaction region, suitably phased. As a consequence of this motion, the beam-beam interaction rate is modulated in synchronism with the beam motion when the beams are not centered on one another. The amplitude and phase of this modulation yields information on the magnitude and direction of the misalignment between the beams, allowing continuous display and automatic correction of any misalignment

  12. The potential application of rice bran wax oleogel to replace solid fat and enhance unsaturated fat content in ice cream.

    Science.gov (United States)

    Zulim Botega, Daniele C; Marangoni, Alejandro G; Smith, Alexandra K; Goff, H Douglas

    2013-09-01

    The development of structure in ice cream, characterized by its smooth texture and resistance to collapse during melting, depends, in part, on the presence of solid fat during the whipping and freezing steps. The objective of this study was to investigate the potential application of 10% rice bran wax (RBW) oleogel, comprised 90% high-oleic sunflower oil and 10% RBW, to replace solid fat in ice cream. A commercial blend of 80% saturated mono- and diglycerides and 20% polysorbate 80 was used as the emulsifier. Standard ice cream measurements, cryo-scanning electron microscopy (cryo-SEM), differential scanning calorimetry (DSC), and transmission electron microscopy (TEM) were used to evaluate the formation of structure in ice cream. RBW oleogel produced higher levels of overrun when compared to a liquid oil ice cream sample, creating a lighter sample with good texture and appearance. However, those results were not associated with higher meltdown resistance. Microscopy revealed larger aggregation of RBW oleogel fat droplets at the air cell interface and distortion of the shape of air cells and fat droplets. Although the RBW oleogel did not develop sufficient structure in ice cream to maintain shape during meltdown when a mono- and diglycerides and polysorbate 80 blend was used as the emulsifier, micro- and ultrastructure investigations suggested that RBW oleogel did induce formation of a fat globule network in ice cream, suggesting that further optimization could lead to an alternative to saturated fat sources for ice cream applications. © 2013 Institute of Food Technologists®

  13. Qualification of technical personnel for employment during construction and operation of the SSC

    International Nuclear Information System (INIS)

    Johnson, C.D.; Wolf, L.J.

    1991-01-01

    In the early stages of the SSC design it became apparent that construction will have a significant impact on post-secondary technical/vocational education in Texas. Present estimates are that from 2,000 to 3,000 employees will be needed in the traditional fields of civil, mechanical, electrical technology, computers as well as exotic technologies such as cryogenics and high vacuum. In this paper an on-going project is described which is directed toward assuring that graduates of Texas post-secondary technical and vocational education programs will be competitive for employment in these jobs. The project involves development of SSC pedagogical material at a level appropriate to the students, education of teachers about the SSC and development of delivery systems for education about the SSC

  14. Proceedings of the international workshop on solenoidal detectors for the SSC

    International Nuclear Information System (INIS)

    Abe, Fumio; Hasegawa, Katsuo

    1990-07-01

    This issue is the collection of the papers presented at the International Workshop on solenoidal detectors for the Superconducting Super Collider (SSC). The 48 of the presented papers are indexed individually. (J.P.N.)

  15. Increasing NASA SSC Range Safety by Developing the Framework to Monitor Airspace and Enforce Restrictions

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA John C. Stennis Space Center (SSC) Office of Safety and Mission Assurance (SMA) has a safety concern associated with unauthorized aircraft entering...

  16. A full-acceptance detector for SSC physics at low and intermediate mass scales

    International Nuclear Information System (INIS)

    Bjorken, J.D.

    1992-01-01

    The author of this paper is interested in seeing the proposed detector and physics measurements done at the SSC. It should be clear that the author views this subject as important enough to warrant the effort going into producing this tome. It should also be clear that nothing will happen unless members of the experimental community come forward and do real work to see whether the ideas contained herein are sound and that the physics is indeed worth a dedicated effort at the SSC. Therefore this paper is directed more toward the experimental community than the SSC Laboratory. However, since initial encouragement (or discouragement) by the laboratory is evidently very important, this paper also contains specific requests addressed to the SSC Laboratory

  17. Detection of H0 → γγ at the SSC

    International Nuclear Information System (INIS)

    Barter, C.; Partridge, R.; Bay, A.; Spadafora, A.; Whitaker, S.; Abashian, A.; Kass, R.

    1989-01-01

    This paper explores the prospects for using the SSC to find an intermediate mass Higgs boson through its decay to two photons. Monte Carlo studies of the signal and various backgrounds are performed to determine the required detector parameters

  18. Performance evaluation of concrete bridge decks reinforced with MMFX and SSC rebars.

    Science.gov (United States)

    2006-01-01

    This report investigates the performance of bridge decks reinforced with stainless steel clad (SSC) and micro-composite multistructural formable steel (MMFX) rebars. The two-span Galloway Road Bridge on route CR5218 over North Elkhorn Creek in Scott ...

  19. Determination of aromatic fragment content in phenol-containing fractions of solid fuel conversion products using nuclear magnetic resonance spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Kanitskaya, L.V.; Kushnarev, D.F.; Polonov, V.M.; Kalabin, G.A.

    1986-03-01

    Optimum conditions are determined for obtaining quantitative nuclear magnetic resonance /sup 13/C spectra of fragments in phenol-containing fraction of coal products. Causes are analyzed of residual signals in spectra of un-protonized carbon atoms. The tests were carried out on: low-temperature carbonization tar and phenol fraction obtained during medium-temperature coking of Cherenkhovskii coal (which contains 84.13% C; 9.68% H; 1.23% S; 4.96% O); products of tar hydrogenation with various phenol content; standard phenol mixture. It was found that quantitative determination of aromatic fraction content in coal conversion products and other phenol- and amine-containing complex mixtures, using NMR spectroscopy requires the addition of dimethylsulfide or acetone in order to suppress specific interactions of phenols (amines) with relaxants and obtain quantitative subspectra of Tertiary and Quaternary aromatic carbon atoms. 16 references.

  20. Biological conversion of forage sorghum biomass to ethanol by steam explosion pretreatment and simultaneous hydrolysis and fermentation at high solid content

    Energy Technology Data Exchange (ETDEWEB)

    Manzanares, Paloma; Ballesteros, Ignacio; Negro, Maria Jose; Oliva, Jose Miguel; Gonzalez, Alberto; Ballesteros, Mercedes [Renewable Energy Department-CIEMAT, Biofuels Unit, Madrid (Spain)

    2012-06-15

    In this work, forage sorghum biomass was studied as feedstock for ethanol production by a biological conversion process comprising the steps of hydrothermal steam explosion pretreatment, enzymatic hydrolysis with commercial enzymes, and fermentation with the yeast Saccharomyces cerevisiae. Steam explosion conditions were optimized using a response surface methodology considering temperature (180-230 C) and time (2-10 min). Sugar recovery in the pretreatment and the enzymatic digestibility of the pretreated solid were used to determine the optimum conditions, i.e., 220 C and 7 min. At these conditions, saccharification efficiency attained 89 % of the theoretical and the recovery of xylose in the prehydrolyzate accounted for 35 % of the amount of xylose present in raw material. Then, a simultaneous hydrolysis and fermentation (SSF) process was tested at laboratory scale on the solid fraction of forage sorghum pretreated at optimum condition, in order to evaluate ethanol production. The effect of the enzyme dose and the supplementation with xylanase enzyme of the cellulolytic enzyme cocktail was studied at increasing solid concentration up to 18 % (w/w) in SSF media. Results show good performance of SSF in all consistencies tested with a significant effect of increasing enzyme load in SSF yield and final ethanol concentration. Xylanase supplementation allows increasing solid concentration up to 18 % (w/w) with good SSF performance and final ethanol content of 55 g/l after 4-5 days. Based on this result, about 190 l of ethanol could be obtained from 1 t of untreated forage sorghum, which means a transformation yield of 85 % of the glucose contained in the feedstock. (orig.)

  1. Mechanical and electromagnetic design of the SSC QSE101 quadrupole ends

    International Nuclear Information System (INIS)

    Orrell, D.; Nobrega, F.; Lilly, J.; Snitchler, G.; Jayakumar, J.; Venkatraman, V.; Brandt, J.S.

    1992-01-01

    The SSC collider magnets feature grouped ends in which cables of a particular coil remain stacked together as they are bent around the end. Methods have been developed to form the ends in such a way that mechanical stresses are lowered and field quality is optimized. This paper discusses techniques of end turn design and presents calculations of harmonics and peak fields for the SSC quadrupole QSE101

  2. Mechanical and electromagnetic design of the SSC QSE101 quadrupole ends

    International Nuclear Information System (INIS)

    Orrell, D.; Nobrega, F.; Lilly, J.; Snitchler, G.; Jayakumar, J.; Venkatraman, V.; Brandt, J.S.

    1991-06-01

    The SSC collider magnets feature grouped ends in which cables of a particular coil remain stacked together as they are gent around the end. methods have been developed to form the ends in such a way that mechanical stresses are lowered and field quality is optimized. This paper discusses techniques of end turn design and presents calculations of harmonics and peak fields for the SSC quadrupole QSE101. 5 refs., 9 figs

  3. EVALUATING THE EFFECTIVENESS OF TEACHING METHODS USED FOR GCE AND SSC LEVELS

    OpenAIRE

    Bhatti, Muhammad Safdar; Mukhtar, Rafia; Bajwa, Shahla

    2017-01-01

    Thepresent research focuses on comparative study of the Secondary SchoolCertificate (SSC) and the General Certificate of Education-Ordinary level(GCE-O level) English language course to trace out the problems andshortcomings of the curriculum objectives and teaching methods. The objectivesof the study were to analyze the objectives of teaching English of SSC and GCEO-level to critically review the teaching methodologies of both the courses.The population of the study comprised of all the teac...

  4. Design and analysis of the SSC [Superconducting Super Collider] dipole magnet suspension system

    International Nuclear Information System (INIS)

    Nicol, T.H.; Niemann, R.C.; Gonczy, J.D.

    1989-03-01

    The design of the suspension system for Superconducting Super Collider (SSC) dipole magnets has been driven by rigorous thermal and structural requirements. The current system, designed to meet those requirements, represents a significant departure from previous superconducting magnet suspension system designs. This paper will present a summary of the design and analysis of the vertical and lateral suspension as well as the axial anchor system employed in SSC dipole magnets. 5 refs., 9 figs., 4 tabs

  5. Magnetic field measurements of full length 50 mm aperture SSC dipole magnets at Fermilab

    International Nuclear Information System (INIS)

    Strait, J.; Bossert, R.; Carson, J.; Delchamps, S.W.; Gourlay, S.; Hanft, R.; Koska, W.; Kuchnir, M.; Lamm, M.J.; Mazur, P.O.; Mokhtarani, A.; Orris, D.; Ozelis, J.; Wake, M.; Devred, A.; DiMarco, J.; Kuzminski, J.; Puglisi, M.; Tompkins, J.C.; Yu, Y.; Zhao, Y.; Zheng, H.; Ogitsu, T.

    1992-09-01

    Thirteen 16 m long, 50 mm aperture SSC dipole magnets, designed jointly by Fermilab, Brookhaven National Laboratory, Lawrence Berkeley Laboratory and the SSC Laboratory, have been built at Fermilab. The first nine magnets have been fully tested to date. The allowed harmonics are systematically shifted from zero by amounts larger than the specification. The unallowed harmonics, with the exception of the skew sextupole, are consistent with zero. The magnet-to-magnet RMS variation of all harmonics is much smaller than the specification

  6. SSCTRK: A particle tracking code for the SSC

    International Nuclear Information System (INIS)

    Ritson, D.

    1990-07-01

    While many indirect methods are available to evaluate dynamic aperture there appears at this time to be no reliable substitute to tracking particles through realistic machine lattices for a number of turns determined by the storage times. Machine lattices are generated by ''Monte Carlo'' techniques from the expected rms fabrication and survey errors. Any given generated machine can potentially be a lucky or unlucky fluctuation from the average. Therefore simulation to serve as a predictor of future performance must be done for an ensemble of generated machines. Further, several amplitudes and momenta are necessary to predict machine performance. Thus to make Monte Carlo type simulations for the SSC requires very considerable computer resources. Hitherto, it has been assumed that this was not feasible, and alternative indirect methods have been proposed or tried to answer the problem. We reexamined the feasibility of using direct computation. Previous codes have represented lattices by a succession of thin elements separated by bend-drifts. With ''kick-drift'' configurations, tracking time is linear in the multipole order included, and the code is symplectic. Modern vector processors simultaneously handle a large number of cases in parallel. Combining the efficiencies of kick drift tracking with vector processing, in fact, makes realistic Monte Carlo simulation entirely feasible. SSCTRK uses the above features. It is structured to have a very friendly interface, a very wide latitude of choice for cases to be run in parallel, and, by using pure FORTRAN 77, to interchangeably run on a wide variety of computers. We describe in this paper the program structure operational checks and results achieved

  7. Investigation and analysis to the content of natural radionuclides at rate-earth ore and solid waste in China through the first nationwide pollution source survey

    International Nuclear Information System (INIS)

    Lou Jianjun; Liu Guifang; Sun Qinghong

    2011-01-01

    China has launched the First Nationwide Pollution Source Survey (FNPSS) during 2006-2009. Ministry Environmental Protection (MEP) sponsored the campaign of measuring the natural radionuclide contents. And the Ministry Environmental Protection (MEP) organized the measurements of natural radionuclide contents of in the factories and mines associated with rare-earth, niobium/tantalum, zircon, tin, lead/zinc, copper, iron, phosphate, coal, aluminum and vanadium. This paper analyzes mainly the data on the contents of U, 232 Th and 226 Ra in the rare-earth ore and solid waste produced by the rare-earth industry in China, as one of a series of papers on naturally occurring radioactive materials (NORM) s investigation. It is concluded that the average of the U, 232 Th and 226 Ra for the monazite sand of rare-earth ore is 16911, 49683, and 20072 Bq/kg, respectively. The average of U, 232 Th and 226 Ra in bastnaesite is 42, 701 and 91 Bq/kg, respectively. The average of U, 232 Th and 226 Ra in the ionic type rare-earth ore is 3918.6, 2315 and 1221 Bq/kg, respectively. (authors)

  8. HEMATOPOIETIC PROGENITOR CELL CONTENT OF VERTEBRAL BODY MARROW USED FOR COMBINED SOLID ORGAN AND BONE MARROW TRANSPLANTATION

    Science.gov (United States)

    Rybka, Witold B.; Fontes, Paulo A.; Rao, Abdul S.; Winkelstein, Alan; Ricordi, Camillo; Ball, Edward D.; Starzl, Thomas E.

    2010-01-01

    While cadaveric vertebral bodies (VB) have long been proposed as a suitable source of bone marrow (BM) for transplantation (BMT), they have rarely been used for this purpose. We have infused VB BM immediately following whole organ (WO) transplantation to augment donor cell chimerism. We quantified the hematopoietic progenitor cell (HPC) content of VB BM as well as BM obtained from the iliac crests (IC) of normal allogeneic donors (ALLO) and from patients with malignancy undergoing autologous marrow harvest (AUTO). Patients undergoing WOIBM transplantation also had AUTO BM harvested in the event that subsequent lymphohematopoietic reconstitution was required. Twenty-four VB BM, 24 IC BM-ALLO, 31 IC AUTO, and 24 IC WO-AUTO were harvested. VB BM was tested 12 to 72 hr after procurement and infused after completion ofWO grafting. IC BM was tested and then used or cryopreserved immediately. HPC were quantified by clonal assay measuring CFU-GM, BFU-E, and CFU-GEMM, and by flow cytometry for CD34+ progenitor cells. On an average, 9 VB were processed during each harvest, and despite an extended processing time the number of viable nucleated cells obtained was significantly higher than that from IC. Furthermore, by HPC content, VB BM was equivalent to IC BM, which is routinely used for BMT. We conclude that VB BM is a clinically valuable source of BM for allogeneic transplantation. PMID:7701582

  9. Analyzer for measurement of nitrogen oxide concentration by ozone content reduction in gas using solid state chemiluminescent sensor

    Science.gov (United States)

    Chelibanov, V. P.; Ishanin, G. G.; Isaev, L. N.

    2014-05-01

    Role of nitrogen oxide in ambient air is described and analyzed. New method of nitrogen oxide concentration measurement in gas phase is suggested based on ozone concentration measurement with titration by nitrogen oxide. Research of chemiluminescent sensor composition is carried out on experimental stand. The sensor produced on the base of solid state non-activated chemiluminescent composition is applied as ozone sensor. Composition is put on the surface of polymer matrix with developed surface. Sensor compositions includes gallic acid with addition of rodamine-6G. Model of interaction process between sensor composition and ozone has been developed, main products appeared during reaction are identified. The product determining the speed of luminescense appearance is found. This product belongs to quinone class. Then new structure of chemiluminescent composition was suggested, with absence of activation period and with high stability of operation. Experimental model of gas analyzer was constructed and operation algorithm was developed. It was demonstrated that developed NO measuring instrument would be applied for monitoring purposes of ambient air. This work was partially financially supported by Government of Russian Federation, Grant 074-U01

  10. Effect of Ni content on the morphological evolution of Ni-YSZ solid oxide fuel cell electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Chen-Wiegart, Yu-chen Karen; Kennouche, David; Scott Cronin, J.; Barnett, Scott A.; Wang, Jun

    2016-02-22

    The coarsening of Ni in Ni–yttria-stabilized zirconia (YSZ) anodes is a potential cause of long term solid oxide fuel cells (SOFC) performance degradation. The specifics of the Ni-YSZ structure—including Ni/YSZ ratio, porosity, and particle size distributions—are normally selected to minimize anode polarization resistance, but they also impact long-term stability. A better understanding of how these factors influence long-term stability is important for designing more durable anodes. The effect of structural details, e.g., Ni-YSZ ratio, on Ni coarsening has not been quantified. Furthermore, prior measurements have been done by comparing evolved structures with control samples, such that sample-to-sample variations introduce errors. Here, we report a four dimensional (three spatial dimensions and time) study of Ni coarsening in Ni-YSZ anode functional layers with different Ni/YSZ ratios, using synchrotron x-ray nano-tomography. The continuous structural evolution was observed and analyzed at sub-100 nm resolution. It is shown quantitatively that increasing the Ni/YSZ ratio increases the Ni coarsening rate. This is due to both increased pore volume and a decrease in the YSZ volume fraction, such that there is more free volume and a less obtrusive YSZ network, both of which allow greater Ni coarsening. The results are shown to be in good agreement with a power-law coarsening model. The finding is critical for informing the design of SOFC electrode microstructures that limit coarsening and performance degradation.

  11. Effect of Ni content on the morphological evolution of Ni-YSZ solid oxide fuel cell electrodes

    Science.gov (United States)

    Chen-Wiegart, Yu-chen Karen; Kennouche, David; Scott Cronin, J.; Barnett, Scott A.; Wang, Jun

    2016-02-01

    The coarsening of Ni in Ni-yttria-stabilized zirconia (YSZ) anodes is a potential cause of long term solid oxide fuel cells (SOFC) performance degradation. The specifics of the Ni-YSZ structure—including Ni/YSZ ratio, porosity, and particle size distributions—are normally selected to minimize anode polarization resistance, but they also impact long-term stability. A better understanding of how these factors influence long-term stability is important for designing more durable anodes. The effect of structural details, e.g., Ni-YSZ ratio, on Ni coarsening has not been quantified. Furthermore, prior measurements have been done by comparing evolved structures with control samples, such that sample-to-sample variations introduce errors. Here, we report a four dimensional (three spatial dimensions and time) study of Ni coarsening in Ni-YSZ anode functional layers with different Ni/YSZ ratios, using synchrotron x-ray nano-tomography. The continuous structural evolution was observed and analyzed at sub-100 nm resolution. It is shown quantitatively that increasing the Ni/YSZ ratio increases the Ni coarsening rate. This is due to both increased pore volume and a decrease in the YSZ volume fraction, such that there is more free volume and a less obtrusive YSZ network, both of which allow greater Ni coarsening. The results are shown to be in good agreement with a power-law coarsening model. The finding is critical for informing the design of SOFC electrode microstructures that limit coarsening and performance degradation.

  12. Survey of SSC12 regions affecting fatty acid composition of intramuscular fat using high density SNP data

    Directory of Open Access Journals (Sweden)

    María eMuñoz

    2012-01-01

    Full Text Available Fatty acid composition is a critical aspect of pork because it affects sensorial and technological aspects of meat quality and it is relevant for human health. Previous studies identified significant QTLs in porcine chromosome 12 for fatty acid profile of backfat and intramuscular fat. In the present study, 374 SNPs mapped in SSC12 from the 60K Porcine SNP Beadchip were used. We have combined linkage and association analyses with expression data analysis in order to identify regions of SSC12 that could affect fatty acid composition of intramuscular fat in longissimus muscle. The QTL scan showed a region around the 60 cM position that significantly affects palmitic fatty acid and two related fatty acid indexes. The Iberian QTL allele increased the palmitic content (+2.6% of mean trait. This QTL does not match any of those reported in the previous study on fatty acid composition of backfat, suggesting different genetic control acting at both tissues. The SNP association analyses showed significant associations with linolenic and palmitic acids besides several indexes. Among the polymorphisms that affect palmitic fatty acid and match the QTL region at 60 cM, there were three that mapped in the Phosphatidylcholine Transfer Protein (PCTP gene and one in the Acetyl-CoA Carboxylase  gene (ACACA. Interestingly one of the PCTP SNPs also affected significantly unsaturated and double bound indexes and the ratio between polyunsaturated/monounsaturated fatty acids. Differential expression was assessed on longissimus muscle conditional on the genotype of the QTL and on the most significant SNPs, according to the results obtained in the former analyses. Results from the microarray expression analyses, validated by RT-qPCR, showed that PCTP expression levels significantly vary depending on the QTL as well as on the own PCTP genotype. The results obtained with the different approaches point out the PCTP gene as a powerful candidate underlying the QTL for

  13. Performance of the MAGCOOL-subcooler cryogenic system after SSC quadrupole quenches

    International Nuclear Information System (INIS)

    Wu, K.C.

    1993-01-01

    The subcooler assembly installed in the MAGCOOL magnet test area at Brookhaven National Laboratory has been used for testing SSC dipoles, quadrupoles and a spool piece since 1989. A detailed description of the system, its steady state capacity and the performance after quenches of a 50 mm SSC dipole were given. Subsequent studies on low current quenches of the SSC dipoles and quenches of the RHIC dipoles were also carried out. In this paper, the performance of the subcooler after quenches of the SSC quadrupole QCC404 is presented. Pressures, temperatures and flow rates in the magnet cooling loop after magnet quenches are given as a function of time. The cooling rates and total energy removed by cooling during quench recovery have been calculated for quench currents between 2000 and 7952 amperes. Because the inductance of the quadrupole is about one tenth that of a SSC dipole, the stored energy released is small and the impact on the system is mild. The cooling loop pressure never exceeds 12 atmospheres and the cryogenic system recovers in less than 15 minutes. As in all past studies, the peak pressure and temperature in the magnet cooling loop are linearly proportional to the energy released during a quench and excellent agreement between the total cooling provided and the magnetic stored energy is found

  14. Sawtooth-wave prebuncher with dual-gaps in Linac injector for HIRFL-SSC

    Science.gov (United States)

    Zhang, Xiaohu; Yuan, Youjin; Xia, Jiawen; Yin, Xuejun; Jin, Peng; Xu, Zhe; Du, Heng; Li, Zhongshan; Qiao, Jian; Wang, Kedong

    2018-01-01

    An RFQ structure is normally composed of radial matcher, shaper, gentle buncher and accelerator section with changing cell geometry. Bunching is started in the shaper, and adiabatic bunching is done in gentle buncher section. The beam preforms from DC beam to bunch beam through the RFQ and the longitudinal emittance for the ions linacs is defined initially in the RFQ, in which the beam bunch has been shaped. In the present SSC-Linac injector, an RFQ has been designed to accelerate the continuous beam from 3.728 keV/u to 143 keV/u. The heavy ions beam is injected into the SSC (Separated Sector Cyclotron) with the kinetic energy of 1.025 MeV/u after four IH DTLs. The rf frequency of the SSC is 13.417 MHz, and the frequency of the heavy ions RFQ is set to four times of the rf frequency of the SSC. In order to increase the longitudinal capture efficiency of the SSC and suppress the longitudinal emittance at the exit of RFQ, an external MHB (Multi-Harmonics Buncher) is proposed in front of the RFQ. The fundamental frequency of the MHB is the same as the rf frequency of the cyclotron. The scheme of dual-gaps prebuncher with the sawtooth waveform is firstly carried out through multi-harmonics synthetic technology. The multi-particle beam dynamic simulations of the MHB have been done by the BEAMPATH code.

  15. Theoretical methods for creep and stress relaxation studies of SSC coil

    International Nuclear Information System (INIS)

    McAdams, J.; Markley, F.

    1992-04-01

    Extrapolation of laboratory measurements of SSC coil properties to the actual construction of SSC magnets requires mathematical models of the experimental data. A variety of models were used to approximate the data collected from creep and stress relaxation experiments performed on Kapton film and SSC coil samples. The coefficients for these mathematical models were found by performing a least-squares fit via the program MINUIT. Once the semiempirical expressions for the creep data were found, they were converted to expressions for stress relaxation using an approximate I pn of the Laplace integral relating the two processes. The data sets from creep experiments were also converted directly to stress relaxation data by numeric integration. Both of these methods allow comparison of data from two different methods of measuring viscoelastic properties. Three companion papers presented at this conference will present: Stress relaxation in SSC 50mm dipole coil. Measurement of the elastic modulus of Kapton perpendicular to the plane of the film at room and cryogenic temperatures. Temperature dependence of the viscoelastic properties of SSC coil insulation (Kapton)

  16. Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature

    Energy Technology Data Exchange (ETDEWEB)

    Saqib, Naeem, E-mail: naeem.saqib@oru.se; Bäckström, Mattias, E-mail: mattias.backstrom@oru.se

    2014-12-15

    Highlights: • Different solids waste incineration is discussed in grate fired and fluidized bed boilers. • We explained waste composition, temperature and chlorine effects on metal partitioning. • Excessive chlorine content can change oxide to chloride equilibrium partitioning the trace elements in fly ash. • Volatility increases with temperature due to increase in vapor pressure of metals and compounds. • In Fluidized bed boiler, most metals find themselves in fly ash, especially for wood incineration. - Abstract: Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine

  17. Effect of Acetylene Black Content in Li4Ti5O12 Xerogel Solid-State Anode Materials on Half-Cell Li-ion Batteries Performance

    Science.gov (United States)

    Abdurrahman, N. M.; Priyono, B.; Syahrial, A. Z.; Subhan, A.

    2017-07-01

    The effect of Acetylene Black (AB) additive contents in lithium titanate/Li4Ti5O12 (LTO) anode on Li-ion Batteries performance is studied in this work. The LTO active material for Li-ion batteries anode was successfully synthesized using sol-gel method to form TiO2 xerogel continued by mixing process with LiOH in ball-mill and then sintered to obtain spinel LTO. The LTO powder is characterized by X-Ray Diffraction (XRD), scanning electron microscopy-Energy Dispersive Spectroscopy (SEM-EDS), and Brunauer-Emmett-Teller (BET). The spinel LTO and TiO2 rutile were detected by XRD diffractogram. The LTO powder is in the form of agglomerates structure. This powder then was mixed with PVDF binder (10%wt) and AB additives with various amount from 10%wt (LTO2 Ac-1), 12%wt (LTO2 Ac-2), and 15%wt (LTO2 Ac-3) of total weight solid content to form electrode sheet. Half-cell coin battery was made with lithium metal foil as a counter electrode. Cyclic voltammetry (CV), Electrochemical-impedance spectroscopy (EIS), and charge discharge (CD) test used to examine the battery performance. The highest resistance value is obtained in LTO2 Ac-3 sample with 15%wt of AB. It might be caused by the formation of side reaction product on electrode surface at initial cycle due to high reactivity of LTO2 Ac-3 electrode. The highest initial capacity at CV test and CD test was obtained in LTO2 Ac-1 (10%wt AB) sample, due to the best proportion of active material content in the compound. While, in the charge-discharge test at high current rate, the best sample rate-capability performance belongs to LTO2 Ac-3 sample (15%wt AB), which still have 24.12 mAh/g of discharge capacity at 10 C with 71.34% capacity loss.

  18. Test results from recent 1.8-m SSC [Superconducting Super Collider] model dipoles

    International Nuclear Information System (INIS)

    Wanderer, P.; Cottingham, J.G.; Dahl, P.

    1988-01-01

    We report results from four 1.8 m-long dipoles built as part of the Superconducting Super Collider (SSC) RandD program. Except for length, these models have the features of the SSC design, which is based on a two-layer cosine theta coil with 4 cm aperture. As compared to the 17 m design length SSC dipoles, these 1.8 m magnets are a faster and more economical way of testing design changes in field shape, conductor support in the coil straight-section and ends, etc. The four magnets reported here all reach fields in excess of 7.5T with little training and have excellent field shape. 10 refs., 2 figs., 3 tabs

  19. Coherent production of {epsilon}{sup +} particles in crystal using proton beam from SSC

    Energy Technology Data Exchange (ETDEWEB)

    Okorokov, V.V.; Dubin, A.Yu. [ITER, Moscow, (Russian Federation)

    1995-05-01

    The unique possibilities of the SSC can be ideally used for a new generation of coherent generation experiments with relativistic protons which require 20 Tev energy of the incident beam. The availability of 20 Tev proton beam at SSC allows new experiments on coherent production of {var_epsilon}{sup +} particle by relativistic proton in crystal. Experiment carried out at low energies can now be extended with protons in very narrow energy region (resonance energy, which easy can be calculated) using the new accelerator facilities at SSC. We propose to study coherent production via the Coulomb field of the cristal atoms to excite the transition p + {gamma}{implies} {var_epsilon} {sup +} (1189).

  20. Modelling formation of new radiation belts and response to ULF oscillations following March 24, 1991 SSC

    International Nuclear Information System (INIS)

    Hudson, M.K.; Kotelnikov, A.D.; Li, X.; Lyon, J.G.; Roth, I.; Temerin, M.; Wygant, J.R.; Blake, J.B.; Gussenhoven, M.S.; Yumoto, K.; Shiokawa, K.

    1996-01-01

    The rapid formation of a new proton radiation belt at L≅2.5 following the March 24, 1991 Storm Sudden Commencement (SSC) observed at the CRRES satellite is modelled using a relativistic guiding center test particle code. The new radiation belt formed on a time scale shorter than the drift period of eg. 20 MeV protons. The SSC is modelled by a bipolar electric field and associated compression and relaxation in the magnetic field, superimposed on a background dipole magnetic field. The source population consists of solar protons that populated the outer magnetosphere during the solar proton event that preceeded the SSC and trapped inner zone protons. The simulations show that both populations contribute to drift echoes in the 20 endash 80 MeV range measured by the Aerospace instrument and in lower energy channels of the Protel instrument on CRRES, while primary contribution to the newly trapped population is from solar protons. Proton acceleration by the SSC differs from electron acceleration in two notable ways: different source populations contribute and nonrelativistic conservation of the first adiabatic invariant leads to greater energization of protons for a given decrease in L than for relativistic electrons. Model drift echoes, energy spectra and flux distribution in L at the time of injection compare well with CRRES observations. On the outbound pass, ∼2 hours after the SSC, the broad spectral peak of the new radiation belt extends to higher energies (20 endash 40 MeV) than immediately after formation. Electron flux oscillations observed at this later time are attributed to post-SSC impulses evident in ground magnetograms, while two minute period ULF oscillations also evident in CRRES field data appear to be cavity modes in the inner magnetosphere. copyright 1996 American Institute of Physics

  1. Bipolar and unipolar tests of 1.5m model SSC collider dipole magnets at Fermilab

    International Nuclear Information System (INIS)

    Lamm, M.J.; Ozelis, J.P.; Coulter, K.J.; Delchamps, S.; Jaffery, T.S.; Kinney, W.; Koska, W.; Strait, J.; Wake, M.; Fortunato, D.; Johnson, D.E.

    1991-05-01

    Tests have been performed at Fermilab on 1.5 m magnetic length model SSC collider dipoles using both bipolar and unipolar ramp cycles. Hysteresis energy loss due to superconductor and iron magnetization and eddy currents is measured and compared as a function of various ramp parameters. Additionally, magnetic field measurements have been performed for both unipolar and bipolar ramp cycles. Measurements such as these will be used to estimate the heat load during collider injection for the SSC High Energy Booster dipoles. 9 refs., 4 figs

  2. Correction of magnetization sextupole and decapole in a 5 centimeter bore SSC dipole using passive superconductor

    International Nuclear Information System (INIS)

    Green, M.A.

    1991-05-01

    Higher multipoles due to magnetization of the superconductor in four and five centimeter bore Superconducting Super Collider (SSC) superconducting dipole magnets have been observed. The use of passive superconductor to correct out the magnetization sextupole has been demonstrated on two dipoles built by the Lawrence Berkeley Laboratory (LBL). This reports shows how passive correction can be applied to the five centimeter SSC dipoles to remove sextupole and decapole caused by magnetization of the dipole superconductor. Two passive superconductor corrector options will be presented. The change in magnetization sextupole and decapole due to flux creep decay of the superconductor during injection can be partially compensated for using the passive superconductor. 9 refs; 5 figs

  3. From mobile ADCP to high-resolution SSC: a cross-section calibration tool

    Science.gov (United States)

    Boldt, Justin A.

    2015-01-01

    Sediment is a major cause of stream impairment, and improved sediment monitoring is a crucial need. Point samples of suspended-sediment concentration (SSC) are often not enough to provide an understanding to answer critical questions in a changing environment. As technology has improved, there now exists the opportunity to obtain discrete measurements of SSC and flux while providing a spatial scale unmatched by any other device. Acoustic instruments are ubiquitous in the U.S. Geological Survey (USGS) for making streamflow measurements but when calibrated with physical sediment samples, they may be used for sediment measurements as well. The acoustic backscatter measured by an acoustic Doppler current profiler (ADCP) has long been known to correlate well with suspended sediment, but until recently, it has mainly been qualitative in nature. This new method using acoustic surrogates has great potential to leverage the routine data collection to provide calibrated, quantitative measures of SSC which hold promise to be more accurate, complete, and cost efficient than other methods. This extended abstract presents a method for the measurement of high spatial and temporal resolution SSC using a down-looking, mobile ADCP from discrete cross-sections. The high-resolution scales of sediment data are a primary advantage and a vast improvement over other discrete methods for measuring SSC. Although acoustic surrogate technology using continuous, fixed-deployment ADCPs (side-looking) is proven, the same methods cannot be used with down-looking ADCPs due to the fact that the SSC and particle-size distribution variation in the vertical profile violates theory and complicates assumptions. A software tool was developed to assist in using acoustic backscatter from a down-looking, mobile ADCP as a surrogate for SSC. This tool has a simple graphical user interface that loads the data, assists in the calibration procedure, and provides data visualization and output options. This tool

  4. Advanced thermohydraulic simulation code for transients in LMFBRs (SSC-L code)

    Energy Technology Data Exchange (ETDEWEB)

    Agrawal, A.K.

    1978-02-01

    Physical models for various processes that are encountered in preaccident and transient simulation of thermohydraulic transients in the entire liquid metal fast breeder reactor (LMFBR) plant are described in this report. A computer code, SSC-L, was written as a part of the Super System Code (SSC) development project for the ''loop''-type designs of LMFBRs. This code has the self-starting capability, i.e., preaccident or steady-state calculations are performed internally. These results then serve as the starting point for the transient simulation.

  5. Summary of the performance of strand produced for the 1990 SSC dipole program

    International Nuclear Information System (INIS)

    Christopherson, D.; Capone, D. II; Seuntjens, J.; Pollock, D.; Hannaford, C.R.

    1991-01-01

    In 1990 and at the beginning of 1991, more than 4 million feet of wire was delivered to support the SSC Dipole Program. This wire was fabricated to meet specification SSC-MAG-M-4141, and test results and various statistics are compiled here. Certain strengths and weaknesses in the performance of the delivered strand are discussed, including analysis of strand breakage in certain billets. Test results of cable manufactured for 40 mm dipole magnets and 50 mm dipole magnets are reported, and a brief overview of the 1991-1992 Conductor Program is included

  6. Summary of the performance of strand produced for the 1990 SSC Dipole Program

    International Nuclear Information System (INIS)

    Christopherson, D.; Capone, D.; Seuntjens, J.; Pollock, D.; Hannaford, C.R.

    1991-03-01

    In 1990 and at the beginning of 1991, more than 4 million feet of wire was delivered to support the SSC Dipole Program. This wire was fabricated to meet specification SSC-MAG-M-4141, and test results and various statistics are compiled here. Certain strengths and weaknesses in the performance of the delivered strand are discussed, including analysis of strand breakage in certain billets. Test results of cable manufactured for 40 mm dipole magnets and 50 mm dipole magnets are reported, and a brief overview of the 1991--1992 Conductor Program is included. 4 refs., 5 figs., 4 tabs

  7. Experimental study of heavy flavor physics and SSC research and development at the University of Mississippi

    International Nuclear Information System (INIS)

    Reidy, J.J.; Cremaldi, L.M.; Summers, D.J.

    1992-01-01

    The High Energy Physics Group has been principally involved with Fermilab experiments on photoproduction and hadroproduction of charm. Nuclear reactions with a mixed 250-GeV hadronic beam and 500-GeV π-N interactions were used. Considerable attention is devoted to the UNIX/RISC computing farm. The Group also has an SSC R ampersand D program dealing with the adaptation and use of the HETC-based detector simulation code CALOR89, the development of liquid scintillator technology for use in SSC detector calorimeters, the hanging file calorimeter project, and the calorimetry program for GEM

  8. Advanced thermohydraulic simulation code for transients in LMFBRs (SSC-L code)

    International Nuclear Information System (INIS)

    Agrawal, A.K.

    1978-02-01

    Physical models for various processes that are encountered in preaccident and transient simulation of thermohydraulic transients in the entire liquid metal fast breeder reactor (LMFBR) plant are described in this report. A computer code, SSC-L, was written as a part of the Super System Code (SSC) development project for the ''loop''-type designs of LMFBRs. This code has the self-starting capability, i.e., preaccident or steady-state calculations are performed internally. These results then serve as the starting point for the transient simulation

  9. Tracking considerations for fixed target B experiments at SSC and LHC

    International Nuclear Information System (INIS)

    McManus, A.P.; Conetti, S.; Corti, G.; Cox, B.; Dukes, E.C.; Lawry, T.; Nelson, K.; Tzamouranis, I.

    1993-01-01

    Fixed target beauty (B) experiments proposed at the SSC or LHC come in two basic types. Extracted beam experiments use a bent crystal of silicon or some other method to extract a beam of protons parasitically from the circulating beam as the collider experiments are taking data. The two chief extracted beam experiments are the LHB collaboration at the LHC and the SFT collaboration at the SSC. The second type of fixed target experiment places the detector around the circulating beam using a gas jet or thin wire(s) as a target. The (GAJET) experiment proposed at CERN for LHC and the Hera-B experiment at DESY are of this type

  10. Experimental Study on Temperature Behavior of SSC (Stiffened Steel Plate Concrete) Structures

    International Nuclear Information System (INIS)

    Lee, K. J.; Ham, K. W.; Park, D. S.; Kwon, K. J.

    2008-01-01

    SSC(Stiffened Steel plate Concrete) module method uses steel plate instead of reinforcing bar and mold in existing RC structure. Steel plate modules are fabricated in advance, installed and poured with concrete in construction field, so construction period is remarkably shortened by SC module technique. In case of existence of temperature gap between internal and external structure surface such as containment building, thermal stress is taken place and as a result of it, structural strength is deteriorated. In this study, we designed two test specimens and several tests with temperature heating were conducted to evaluate temperature behavior of SSC structures and RC structure

  11. Novel Insight for Organic Matter Sourcing: Interest of Time Resolved Fluorescence to Qualify and Quantify PAH Content of Solid Matrix at High Resolution

    Science.gov (United States)

    Quiers, M.; Perrette, Y.; Jacq, K.; Pousset, E.; Plassart, G.

    2017-12-01

    OM fluorescence is today a well-developed tool used to characterize and quantify organic matter (OM), but also to evaluate and discriminate OM fate and changes related to climate and environmental modifications. While fluorescence measurements on water and soils extracts provide information about organic fluxes today, solid phase fluorescence using natural archives allows to obtain high resolution records of OM evolution during time. These evolutions can be discussed in regards of climate and environmental perturbations detected in archives using different proxies, and thus provide keys for understanding factors driving carbon fluxes mechanisms. Among fluorescent organic species, Polycyclic Aromatic Hydrocarbons (PAH) have been used as probe molecules for organic contamination tracking. Moreover, monitoring studies have shown that PAH could also be used as markers to discriminates atmospheric and erosion factors leading to PAH and organic matter fluxes to the aquifer. PAH records in soils and natural archives appear as a promising proxy to follow both past atmospheric contamination and soil erosion. But, PAH fluorescence is difficult to discriminate from bulk OM fluorescence using steady-state fluorescence (SSF) technics as their fluorescence domains recover. Time resolved emission spectroscopy (TRES) increases the information provided by SSF technic, adding a time dimension to measurements and allowing to discriminate PAH fluorescence. We report here a first application of this technic on natural archives. The challenge is to obtain TRES signature along the sample, including for low PAH concentrations. This study aims to evaluate the reliability of high resolution TRES measurement as PAH carbon fluxes sources. Method is based on LIF instrument for solid phase fluorescence measurement. An instrument coupling an excitation system constituting by 2 pulsed lasers (266 and 355 nm) and a detection system was developed. This measurement provides high resolution record of

  12. Dry matter content and fruit size affect flavour and texture of novel Actinidia deliciosa genotypes.

    Science.gov (United States)

    Nardozza, Simona; Gamble, Joanna; Axten, Lauren G; Wohlers, Mark W; Clearwater, Michael J; Feng, Jinquan; Harker, F Roger

    2011-03-15

    Previous studies with commercial kiwifruit cultivars have demonstrated that the taste of fruit with higher dry matter content (DM) is more liked by consumers. A unique replicated trial of kiwifruit genotypes (10 high/low DM × small/large-fruited genotypes) has provided an opportunity to consider how the genetic propensity for a kiwifruit to accumulate DM affects fruit flavour and texture. In the present study, eating-ripe fruit from each of the genotypes were assessed using a trained sensory panel and the relationships between these sensory attributes and fresh weight, DM, flesh firmness and soluble solids content (SSC) were explored. The genotypes provided a diversity of flavour and texture attributes, each of which varied in perceived intensity of the sensory experience. High-DM genotypes had higher SSC and were perceived as sweeter than low-DM genotypes. Sweet taste was closely associated with the perception of the tropical flavour and high-DM genotypes were found to have more tropical notes. Fruit size was associated with fruit texture, and small fruit were characterised by a firmer and more fibrous core. Large high-DM fruit were perceived as juicier than those of all other genotypes. Genotypes were perceived differently from one another, and differences in fruit size and DM content were reflected in fruit sensorial properties. This study is unique in demonstrating interactions between fruit size, DM and sensory properties. These findings could be relevant not only to kiwifruit but to fruiting crop breeders in general, because of the demonstrated potential for effects of fruit size and DM content on sweetness, flavour and fruit texture. Copyright © 2010 Society of Chemical Industry.

  13. Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature.

    Science.gov (United States)

    Saqib, Naeem; Bäckström, Mattias

    2014-12-01

    Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. ATPase Domain and Interdomain Linker Play a Key Role in Aggregation of Mitochondrial Hsp70 Chaperone Ssc1*

    Science.gov (United States)

    Blamowska, Marta; Sichting, Martin; Mapa, Koyeli; Mokranjac, Dejana; Neupert, Walter; Hell, Kai

    2010-01-01

    The co-chaperone Hep1 is required to prevent the aggregation of mitochondrial Hsp70 proteins. We have analyzed the interaction of Hep1 with mitochondrial Hsp70 (Ssc1) and the determinants in Ssc1 that make it prone to aggregation. The ATPase and peptide binding domain (PBD) of Hsp70 proteins are connected by a linker segment that mediates interdomain communication between the domains. We show here that the minimal Hep1 binding entity of Ssc1 consists of the ATPase domain and the interdomain linker. In the absence of Hep1, the ATPase domain with the interdomain linker had the tendency to aggregate, in contrast to the ATPase domain with the mutated linker segment or without linker, and in contrast to the PBD. The closest homolog of Ssc1, bacterial DnaK, and a Ssc1 chimera, in which a segment of the ATPase domain of Ssc1 was replaced by the corresponding segment from DnaK, did not aggregate in Δhep1 mitochondria. The propensity to aggregate appears to be a specific property of the mitochondrial Hsp70 proteins. The ATPase domain in combination with the interdomain linker is crucial for aggregation of Ssc1. In conclusion, our results suggest that interdomain communication makes Ssc1 prone to aggregation. Hep1 counteracts aggregation by binding to this aggregation-prone conformer. PMID:20007714

  15. ATPase domain and interdomain linker play a key role in aggregation of mitochondrial Hsp70 chaperone Ssc1.

    Science.gov (United States)

    Blamowska, Marta; Sichting, Martin; Mapa, Koyeli; Mokranjac, Dejana; Neupert, Walter; Hell, Kai

    2010-02-12

    The co-chaperone Hep1 is required to prevent the aggregation of mitochondrial Hsp70 proteins. We have analyzed the interaction of Hep1 with mitochondrial Hsp70 (Ssc1) and the determinants in Ssc1 that make it prone to aggregation. The ATPase and peptide binding domain (PBD) of Hsp70 proteins are connected by a linker segment that mediates interdomain communication between the domains. We show here that the minimal Hep1 binding entity of Ssc1 consists of the ATPase domain and the interdomain linker. In the absence of Hep1, the ATPase domain with the interdomain linker had the tendency to aggregate, in contrast to the ATPase domain with the mutated linker segment or without linker, and in contrast to the PBD. The closest homolog of Ssc1, bacterial DnaK, and a Ssc1 chimera, in which a segment of the ATPase domain of Ssc1 was replaced by the corresponding segment from DnaK, did not aggregate in Delta hep1 mitochondria. The propensity to aggregate appears to be a specific property of the mitochondrial Hsp70 proteins. The ATPase domain in combination with the interdomain linker is crucial for aggregation of Ssc1. In conclusion, our results suggest that interdomain communication makes Ssc1 prone to aggregation. Hep1 counteracts aggregation by binding to this aggregation-prone conformer.

  16. Total phenolic contents, antioxidant activities, and lipid fractions from berry pomaces obtained by solid-state fermentation of two Sambucus species with Aspergillus niger.

    Science.gov (United States)

    Dulf, Francisc Vasile; Vodnar, Dan Cristian; Dulf, Eva-Henrietta; Toşa, Monica Ioana

    2015-04-08

    The aim of this study was to investigate the effect of solid-state fermentation (SSF) by Aspergillus niger on phenolic contents and antioxidant activity in Sambucus nigra L. and Sambucus ebulus L. berry pomaces. The effect of fermentation time on the total fats and major lipid classes (neutral and polar) was also investigated. During the SSF, the extractable phenolics increased with 18.82% for S. ebulus L. and 11.11% for S. nigra L. The levels of antioxidant activity of methanolic extracts were also significantly enhanced. The HPLC-MS analysis indicated that the cyanidin 3-sambubioside-5-glucoside is the major phenolic compound in both fermented Sambucus fruit residues. In the early stages of fungal growth, the extracted oils (with TAGs as major lipid fraction) increased with 12% for S. nigra L. and 10.50% for S. ebulus L. The GC-MS analysis showed that the SSF resulted in a slight increase of the linoleic and oleic acids level.

  17. Effect of total solid content and pretreatment on the production of lactic acid from mixed culture dark fermentation of food waste.

    Science.gov (United States)

    Yousuf, Ahasa; Bastidas-Oyanedel, Juan-Rodrigo; Schmidt, Jens Ejbye

    2018-04-28

    Food waste landfilling causes environmental degradation, and this work assesses a sustainable food valorization technique. In this study, food waste is converted into lactic acid in a batch assembly by dark fermentation without pH control and without the addition of external inoculum at 37 °C. The effect of total solid (TS), enzymatic and aeration pretreatment was investigated on liquid products concentration and product yield. The maximum possible TS content was 34% of enzymatic pretreated waste, and showed the highest lactic acid concentration of 52 g/L, with a lactic acid selectivity of 0.6 g lactic /g totalacids . The results indicated that aeration pretreatment does not significantly improve product concentration or yield. Non-pretreated waste in a 29% TS system showed a lactic acid concentration of 31 g/L. The results showed that enzymatic pretreated waste at TS of 34% results in the highest production of lactic acid. Copyright © 2018 Elsevier Ltd. All rights reserved.

  18. The Extraction and Determination of Ellagic Acid Content in the Peels of Six Iranian Pomegranates Cultivars Using a New Miniaturized Matrix Solid-Phase Dispersion Method

    Directory of Open Access Journals (Sweden)

    Fariba Nazari Serenjeh

    2017-03-01

    Full Text Available Background and Aim:The peels of six Iranian pomegranates (Punica granatum L. cultivars, as a traditional medicine, were treated with a new miniaturized matrix solid-phase dispersion (MSPD method for the HPLC determination of ellagic acid (EA. Materials and Methods:In the proposed method, only 10mg of the sample powder was ground and blended with an equal amount of C18 sorbent in an agate mortar. The use of the agate mortar with smooth surface facilitated the sample transfer into a cartridge and reduced the required amount of sample and sorbent. Micro volumes of dichloromethane, n-hexane and methanol were used as modifier, washing and elution solvents, respectively. The eluate was injected into an HPLC-UV system for the analysis. Results:Several factors such as the type and amount of dispersing sorbent, modifier, washing solvent and eluent were carefully studied and optimized. Six replicated analyses at the optimized conditions resulted in a recovery of 96.7% and a relative standard deviation of 5.87%. The proposed method was successfully applied to the extraction and determination of EA in the peels samples. Conclusion:According to the ultimate results, the MSPD method is an efficient technique for the quantitative extraction of EA from the peels of pomegranate. Malas cultivar has the highest amount (18.1 g kg-1 of ellagic acid content compared to the other studied pomegranate cultivars.

  19. Experimental study of heavy flavor physics and SSC research and development at The University of Mississippi

    International Nuclear Information System (INIS)

    Reidy, J.J.

    1990-01-01

    This report discusses the following topics: particle production of charmed particle; progress in the SSC research and development program; CALOR/GEANT integration; the calorimeter simulation effort; scintillating plate/liquid argon calorimeter simulation; liquid scintillator R ampersand D; and funding by the TNRLC

  20. PSF blind test SSC, SPVC, and SVBC physics-dosimetry-metallurgy data packages

    International Nuclear Information System (INIS)

    1984-01-01

    Information is presented concerning the final PSF radiometric data; calculated spectral fluences and dosimeter activities for the metallurgical blind test irradiations at the ORR-PSF; fabrication data package for HEDL dosimetry in the ORNL Poolside Facility LWR pressure vessel mock-up irradiation; SSC-1; NUREG-CR-3457; and NUREG-CR-3295

  1. The Disappearing Fourth Wall: John Marburger, Science Policy, and the SSC

    Science.gov (United States)

    Crease, Robert

    2015-04-01

    John H. Marburger (1941-2011) was a skilled science administrator who had a fresh and unique approach to science policy and science leadership. His posthumously published book Science Policy up Close contains recollections of key science policy episodes in which he participated or observed closely. One was the administration of the Superconducting Supercollider (SSC); Marburger was Chairman of the Universities Research Association, the group charged with managing the SSC, from 1988-1994. Many accounts of the SSC saga attribute its demise to a combination of transitory factors: poor management, rising cost estimates, the collapse of the Soviet Union and thus of the Cold War threat, complaints by ``small science'' that the SSC's ``big science'' was consuming their budget, Congress's desire to cut spending, unwarranted contract regulations imposed by the Department of Energy (DOE) in response to environmental lapses at nuclear weapons laboratories, and so forth. Marburger tells a subtler story whose implications for science policy are more significant and far-reaching. The story involves changes in the attitude of the government towards large scientific projects that reach back to management reforms introduced by the administration of Presidents Johnson, Nixon, and Carter in the 1960s and 1970s. This experience impressed Marburger with the inevitability of public oversight of large scientific projects, and with the need for planners of such projects to establish and make public a cost and schedule tracking system that would model the project's progress and expenditures.

  2. Delta-function Approximation SSC Model in 3C 273 S. J. Kang1 ...

    Indian Academy of Sciences (India)

    Abstract. We obtain an approximate analytical solution using δ approximate calculation on the traditional one-zone synchrotron self-. Compton (SSC) model. In this model, we describe the electron energy distribution by a broken power-law function with a sharp cut-off, and non- thermal photons are produced by both ...

  3. Deflection analysis for an SSC [Superconducting Super Collider] dipole magnet with two external supports

    International Nuclear Information System (INIS)

    Nicol, T.H.

    1987-01-01

    SSC dipole magnets are presently supported at five mounting locations coincident with the internal cold mass supports. There is growing interest in reducing the number of external supports from five to two for reasons of simplified installation and alignment and as a cost reduction measure. This reports examines the placement of two external supports required to minimize the deflection of the cold mass assembly

  4. Fermilab R and D test facility for SSC [Superconducting Super Collider] magnets

    International Nuclear Information System (INIS)

    Strait, J.; Bleadon, M.; Hanft, R.; Lamm, M.; McGuire, K.; Mantsch, P.; Mazur, P.O.; Orris, D.; Pachnik, J.

    1989-02-01

    The test facility used for R and D testing of full scale development dipole magnets for the SSC is described. The Fermilab Magnet Test Facility, originally built for production testing of Tevatron magnets, has been substantially modified to allow testing also of SSC magnets. Two of the original six test stands have been rebuilt to accommodate testing of SSC magnets at pressures between 1.3 Atm and 4 Atm and at temperatures between 1.8 K and 4.8 K and the power system has been modified to allow operation to at least 8 kA. Recent magnets have been heavily instrumented with voltage taps to allow detailed study of quench location and propagation and with strain gage based stress, force and motion transducers. A data acquisition system has been built with a capacity to read from each SSC test stand up to 220 electrical quench signals, 32 dynamic pressure, temperature and mechanical transducer signals during quench and up to 200 high precision, low time resolution, pressure, temperature and mechanical transducer signals. The quench detection and protection systems is also described. 23 refs., 4 figs., 2 tabs

  5. Need to plan for a full-scale lns-physics program at the SSC

    International Nuclear Information System (INIS)

    White, A.R.

    1984-03-01

    Arguments for a full lns physics program at the SSC are enumerated and elaborated on. They are: first - the inadequacy of data from a minimal program, second - the potential fundamental significance of a high-energy soft physics collective phenomenon and third - the possible diffractive production of much of the interesting new physics that will be searched for

  6. Review of the abort dump shown in the SSC [superconducting super collider] conceptual design report

    International Nuclear Information System (INIS)

    Cossairt, J.D.

    1987-04-01

    This report details the design of the abort dump for the Superconducting Super-Collider (SSC). The dump is made from graphite and designed to absorb the maximum beam energy of 400 MJ. The report considers long time activation effects of the dump components. The report concludes that the basic design of the abort dump is well defined

  7. Test results of BNL built 40-mm aperture, 17-m-long SSC collider dipole magnets

    International Nuclear Information System (INIS)

    Kuzminski, J.; Bush, T.; Coombes, R.; Devred, A.; DiMarco, J.; Goodzeit, C.; Puglisi, M.; Radusewicz, P.; Sanger, P.; Schermer, R.; Tompkins, J.C.; Wolf, Z.; Yu, Y.; Zheng, H.; Ogitsu, T.; Anerella, M.; Cottingham, J.; Ganetis, G.; Garber, M.; Gosh, A.; Greene, A.; Gupta, R.; Herrera, J.; Kahn, S.; Kelly, E.; Morgan, G.; Muratore, J.; Prodell, A.; Rehak, M.; Rohrer, E.P.; Sampson, W.; Shutt, R.; Thompson, P.; Wanderer, P.; Willen, E.; Bleadon, M.; Hanft, R.; Kuchnir, M.; Mantsch, P.; Mazur, P.O.; Orris, D.; Peterson, T.; Strait, J.; Royet, J.; Scanlan, R.; Taylor, C.

    1991-06-01

    Eleven 17 m long, 40 mm aperture SSC R ampersand D superconducting collider dipole magnets, built at BNL, have been extensively tested at BNL and Fermilab during 1990--91. Quench performance of these magnets and details of their mechanical behavior are presented. 7 refs., 5 figs

  8. The effect of particulate debris on the insulation integrity of SSC coils during molding and collaring

    International Nuclear Information System (INIS)

    Nehrlich, E.; Markley, F.; Rogers, D.

    1991-03-01

    In order to simulate the effect of accidentally introduced debris on SSC coil insulation integrity, models consisting of two pieces of insulated SSC cable have been loaded in an hydraulic press after introducing foreign particles between the layers. The tests were originally suggested by R. Palmer of the SSC Laboratory. A high voltage (2 Kv) was continually applied between the two cables and the load gradually increased until an electrical short occurred. The high voltage was used as an easy method of detecting insulation punctures and to continue the general type of testing begun at Brookhaven by J. Skaritka, now at the SSC Laboratory, and continued at Fermilab by F. Markley and presented at last year's session of the Conference. A range of particles of different size, shape, and hardness were used, and both conducting and insulating particles were included. Fine wires were also used. When the data are normalized using the control (no particles added), data for each cable batch used, there is a slight correlation between pressure at breakdown and particle size for cables insulated with Kapton only. Adjustment must be made for soft particles that tend to deform and for particles with aspect ratios greater than one. Additional measurements have also been made where the opoxy-fiberglass layer was added to the Kapton insulation overwrap. These show a correlation between conductivity and breakdown pressure. 1 ref., 7 figs

  9. Computing and data handling requirements for SSC [Superconducting Super Collider] and LHC [Large Hadron Collider] experiments

    International Nuclear Information System (INIS)

    Lankford, A.J.

    1990-05-01

    A number of issues for computing and data handling in the online in environment at future high-luminosity, high-energy colliders, such as the Superconducting Super Collider (SSC) and Large Hadron Collider (LHC), are outlined. Requirements for trigger processing, data acquisition, and online processing are discussed. Some aspects of possible solutions are sketched. 6 refs., 3 figs

  10. Technical advisory on SSC site criteria and catalog of site information needs

    Energy Technology Data Exchange (ETDEWEB)

    1985-06-15

    The Superconducting Super Collider, or SSC, is a proposed scientific instrument of the study of the fundamental nature of matter. In the SSC two 20-TeV beams of protons will be accelerated and counter circulate on an approximately circular path. The protons will be made to collide at six locations where detectors can be placed to count and measure the products of the collisions. These collisions, twenty times more energetic than in any existing facility, will enable scientists to probe deeper into the heart of matter in the quest for a deeper understanding of the universal forces of nature. The goal of the SSC project is to create a scientific laboratory in high energy physics whose facilities are unique. Ultimately the success of that laboratory will be measured by its scientific discoveries, measurements, interpretations, and innovations. Toward that end the accelerator-collider must be constructed to high standards at minimum cost and maximum effectiveness. Preparations must be made for future operations and a scientific-technical staff attracted and maintained. The chosen site must accommodate all of these factors. This document summarizes siting criteria for the SSC and enumerates site-specific information important to the evaluation of potential sites. This document is not a call for site proposals but a technical report prepared for the information and use of the Department of Energy (DOE).

  11. A high-resolution comparative RH map of porcine chromosome (SSC) 2.

    NARCIS (Netherlands)

    Rattink, A.P.; Faivre, M.; Jungerius, B.J.; Groenen, M.A.M.; Harlizius, B.

    2001-01-01

    A high-resolution comparative map was constructed for porcine Chromosome (SSC) 2, where a QTL for back fat thickness (BFT) is located. A radiation hybrid (RH) map containing 33 genes and 25 microsatellite markers was constructed for this chromosome with a 3000-rad porcine RH panel. In total, 16

  12. Construction experience with Fermilab-built full length 50mm SSC dipoles

    International Nuclear Information System (INIS)

    Blessing, M.J.; Hoffman, D.E.; Packer, M.D.; Gordon, M.; Higinbotham, W.; Sims, R.

    1992-03-01

    Fourteen full length SSC dipole magnets are being built and tested at Fermilab. Their purpose is to verify the magnet design as well as transfer the construction technology to industry. Magnet design is summarized. Construction problems and their solutions are discussed. Topics include coil winding, curing and measuring, collaring, instrumentation, end clamp installation, yoking and electrical and mechanical interconnection

  13. Probing electroweak symmetry breaking at the SSC [Superconducting Super Collider]: A no-lose corollary

    International Nuclear Information System (INIS)

    Chanowitz, M.S.

    1987-01-01

    Low energy theorems are derived for scattering of longitudinally polarized W and Z's, providing the basis for an estimate of the observable signal at the SSC if electroweak symmetry breaking is due to new physics at the TeV scale

  14. Tests of 1.5 meter model 50mm SSC collider dipoles at Fermilab

    International Nuclear Information System (INIS)

    Wake, M.; Bossert, R.; Carson, J.; Coulter, K.; Delchamps, S.; Gourlay, S.; Jaffery, T.S.; Kinney, W.; Koska, W.; Lamm, M.J.; Strait, J.; Sims, R.; Winters, M.

    1991-05-01

    A series of 50mm diameter 1.5m model magnets have been constructed. The test of these magnets gave convincing results concerning the design of the 50mm cross section of the SSC collider dipoles. 9 refs., 6 figs

  15. Planning for Plume Diagnostics for Ground Testing of J-2X Engines at the SSC

    Science.gov (United States)

    SaintCyr, William W.; Tejwani, Gopal D.; McVay, Gregory P.; Langford, Lester A.; SaintCyr, William W.

    2010-01-01

    John C. Stennis Space Center (SSC) is the premier test facility for liquid rocket engine development and certification for the National Aeronautics and Space Administration (NASA). Therefore, it is no surprise that the SSC will play the most prominent role in the engine development testing and certification for the J-2X engine. The Pratt & Whitney Rocketdyne J-2X engine has been selected by the Constellation Program to power the Ares I Upper Stage Element and the Ares V Earth Departure Stage in NASA s strategy of risk mitigation for hardware development by building on the Apollo program and other lessons learned to deliver a human-rated engine that is on an aggressive development schedule, with first demonstration flight in 2010 and human test flights in 2012. Accordingly, J-2X engine design, development, test, and evaluation is to build upon heritage hardware and apply valuable experience gained from past development and testing efforts. In order to leverage SSC s successful and innovative expertise in the plume diagnostics for the space shuttle main engine (SSME) health monitoring,1-10 this paper will present a blueprint for plume diagnostics for various proposed ground testing activities for J-2X at SSC. Complete description of the SSC s test facilities, supporting infrastructure, and test facilities is available in Ref. 11. The A-1 Test Stand is currently being prepared for testing the J-2X engine at sea level conditions. The A-2 Test Stand is currently being used for testing the SSME and may also be used for testing the J-2X engine at sea level conditions in the future. Very recently, ground-breaking ceremony for the new A-3 rocket engine test stand took place at SSC on August 23, 2007. A-3 is the first large - scale test stand to be built at the SSC since the A and B stands were constructed in the 1960s. The A-3 Test Stand will be used for testing J-2X engines under vacuum conditions simulating high altitude operation at approximately 30,480 m (100,000 ft

  16. Deposition of Composite LSCF-SDC and SSC-SDC Cathodes by Axial-Injection Plasma Spraying

    Science.gov (United States)

    Harris, Jeffrey; Qureshi, Musab; Kesler, Olivera

    2012-06-01

    The performance of solid oxide fuel cell cathodes can be improved by increasing the number of electrochemical reaction sites, by controlling microstructures, or by using composite materials that consist of an ionic conductor and a mixed ionic and electronic conductor. LSCF (La0.6Sr0.4Co0.2Fe0.8O3-δ) and SSC (Sm0.5Sr0.5CoO3) cathodes were manufactured by axial-injection atmospheric plasma spraying, and composite cathodes were fabricated by mixing SDC (Ce0.8Sm0.2O1.9) into the feedstock powders. The plasma power was varied by changing the proportion of nitrogen in the plasma gas. The microstructures of cathodes produced with different plasma powers were characterized by scanning electron microscopy and gas permeation measurements. The deposition efficiencies of these cathodes were calculated based on the mass of the sprayed cathode. Particle surface temperatures were measured in-flight to enhance understanding of the relationship between spray parameters, microstructure, and deposition efficiency.

  17. A physiological and genetic approach to the improvement of tomato (Lycopersicon esculentum Mill.) fruit soluble solids

    International Nuclear Information System (INIS)

    Damon, S.E.

    1989-01-01

    Physiological processes and the genetic basis determining soluble solids content (SSC) of processing tomato fruit were addressed. Analysis of [ 3 H]-(fructosyl)-sucrose translocation in tomato indicates that phloem unloading in the fruit occurs, at least in part, to the apoplast. Apoplastic sucrose, glucose and fructose concentrations were estimated as 1 to 7, 12 to 49 and 8 to 63 millimolar, respectively in tomato fruit pericarp. Short-term uptake of [ 14 C]sucrose, -glucose and -fructose in tomato pericarp discs showes first order kinetics over the physiologically relevant concentration range. The uptake of [ 14 C]-(glycosyl)-1'fluorosucrose was identical to the rate of [ 14 C] sucrose uptake suggesting sucrose may be taken up directly without prior extracellular hydrolysis. Short-term uptake of all three sugars was insensitive to 10 micromolar carbonyl cyanide m-chlorophenylhydrazone and to 10 micromolar p-chloromercuribenzene sulfonic acid. However, long-term accumulation of glucose was sensitive to carbonyl cyanide m-chlorophenylhydrazone. Sugar uptake across the plasmamembrane does not appear to be energy dependent, suggesting that sugar accumulation in the tomato is driven by subsequent intracellular metabolism and/or active uptake at the tonoplast. Fourteen genomic DNA probes and ten restriction endonucleases were used to identify restriction fragment length polymorphisms (RFLPs) useful in the linkage analysis of quantitative trait loci controlling the expression of SSC in a segregating F 2 population from a cross between L. esculentum (UC204B) and L. cheesmanii f. minor, a wild species with high fruit soluble solids. RFLPs were detected between the DNAs of the two tomato species with all 14 probes

  18. A cryogenic test stand for full length SSC magnets with superfluid capability

    International Nuclear Information System (INIS)

    Peterson, T.J.; Mazur, P.O.

    1989-02-01

    The Fermilab Magnet Test Facility performs testing of the full scale SSC magnets on test stands capable of simulating the cryogenic environment of the SSC main ring. One of these test stands, Stand 5, also has the ability to operate the magnet under test at temperatures from 1.8K to 4.5K with either supercritical helium or subcooled liquid, providing at least 25 Watts of refrigeration. At least 50 g/s flow is available from 2.3K to 4.5K, whereas superfluid operation occurs with zero flow. Cooldown time from 4.5K to 1.8K is 1.5 hours. A maximum current capability of 10,000 amps is provided, as is instrumentation to monitor and control the cryogenic conditions. This paper describes the cryogenic design of this test stand. 8 refs., 6 figs

  19. An experimental study of the SSC [Superconducting Super Collider] magnet aperture criterion

    International Nuclear Information System (INIS)

    Merminga, N.; Edwards, D.; Finley, D.

    1988-01-01

    A beam dynamics experiment, performed in the Fermilab Tevatron, that was mainly motivated by planning for the Superconducting Super Collider (SSC) is described. Nonlinearities are introduced in the Tevatron by special sextupoles in order to stimulate the SSC environment. ''Smear'' is one of the parameters used to characterize the deviation from linear behavior. Smear is extracted from experimental data and compared with calculation over a wide range of conditions. The agreement is excellent. The closed orbit at injection trajectory reveal no deterioration even at the highest sextupole excitations. Measurements of the dynamic aperture are in general agreement with prediction. Particles captured on nonlinear resonance islands are directly observed and measurements are performed for the first time. The stability of the islands under tune modulation is investigated. 4 refs., 8 figs

  20. Real-time data acquisition and computation for the SSC using optical and electronic technologies

    International Nuclear Information System (INIS)

    Cantrell, C.D.; Fenyves, E.J.; Wallace, B.

    1990-01-01

    The authors discuss combinations of optical and electronic technologies that may be able to address major data-filtering and data-analysis problems at the SSC. Novel scintillation detectors and optical readout may permit the use of optical processing techniques for trigger decisions and particle tracking. Very-high-speed fiberoptic local-area networks will be necessary to pipeline data from the detectors to the triggers and from the triggers to computers. High-speed, few-processor MIMD superconductors with advanced fiberoptic I/O technology offer a usable, cost-effective alternative to the microprocessor farms currently proposed for event selection and analysis for the SSC. The use of a real-time operating system that provides standard programming tools will facilitate all tasks, from reprogramming the detectors' event-selection criteria to detector simulation and event analysis. 34 refs., 1 fig., 1 tab

  1. Considerations on the design of front-end electronics for silicon calorimetry for the SSC

    International Nuclear Information System (INIS)

    Wintenberg, A.L.; Bauer, M.L.; Britton, C.L.; Kennedy, E.J.; Todd, R.A.; Berridge, S.C.; Bugg, W.M.

    1990-01-01

    Some considerations are described for the design of a silicon-based sampling calorimetry detector for the Superconducting Super Collider (SSC). The use of silicon as the detection medium allows fast, accurate, and fine-grained energy measurements - but for optimal performance, the front-end electronics must be matched to the detector characteristics and have the speed required by the high SSC interaction rates. The relation between the signal-to-noise rtio of the calorimeter electronics and the charge collection time, the preamplifier power dissipation, detector capacitance and leakage, charge gain, and signal shaping and sampling was studied. The electrostatic transformer connection was analyzed and found to be unusable for a tightly arranged calorimeter because of stray capacitance effects. The method of deconvolutional sampling was developed as a means for pileup correction following synchronous sampling and analog storage

  2. Statistical factors to qualify the superconducting magnets for the SSC based on warm/cold correlations

    International Nuclear Information System (INIS)

    Kim, K.; Devred, A.; Coles, M.; Tompkins, J.

    1993-05-01

    All of the SSC production magnets will be measured at room temperature (warm), but only a fraction of these will be measured at liquid helium temperature (cold). The fractional information will then be analyzed to determine warm acceptance criteria for the field quality of the SSC magnets. Regarding predictors of the field quality based on partial information, there are several observations and studies based on the warm/cold correlation. A different facet of the acceptance test is production control, which interprets the warm/cold correlation to adjust the process parameters. For these applications, we are evaluating statistical techniques relying on asymptotic estimators of the systematic errors and random errors, and their respective confidence intervals. The estimators are useful to qualify the population magnets based on a subset of sample magnets. We present the status of our work, including: (i) a recapitulation of analytic formulas, (ii) a justification based on HERA magnet experience, and (iii) a practical interpretation of these estimators

  3. HIRFL-SSC trim coil currents calculation by conjugate gradients method

    International Nuclear Information System (INIS)

    Liu, W.

    2005-01-01

    For accelerating different kinds of ions to various energies, the HIRFL-SSC should form the corresponding isochronous magnetic field by its main coil and trim coils. Previously, there were errors in fitting the theoretical isochronous magnetic field in the small radius region, which led to some operation difficulties for ion acceleration in the inject region. After further investigation of the restrictive condition of the maximum current limitation, the trim coil currents for fitting the theoretical isochronous magnetic field were recalculated by the conjugate gradients method. Better results were obtained in the operation of HIRFL-SSC. This article introduces the procedure to calculate the trim coil currents. The calculation method of conjugate gradients is introduced and the fitting error is analysed. (author)

  4. A high gradient quadrupole magnet for the SSC [Superconducting Super Collider

    International Nuclear Information System (INIS)

    Taylor, C.; Caspi, S.; Helm, M.; Mirk, K.; Peters, C.; Wandesforde, A.

    1987-03-01

    A quadrupole magnet for the SSC has been designed with a gradient of 234 T/m at 6500 A. Coil ID is 40 mm. The two-layer windings have 9 inner turns and 13 outer turns per pole with a wedge-shaped spacer in each layer. The 30-strand cable is identical to that used in the outer layer of the SSC dipole magnet. Interlocking aluminum alloy collars are compressed around the coils using a four-way press and are locked with four keys. The collared coil is supported and centered in a cold split iron yoke. A one-meter model was constructed and tested. Design details including quench behavior are presented

  5. FAD: A full-acceptance detector for physics at the SSC

    International Nuclear Information System (INIS)

    Bjorken, J.D.

    1992-09-01

    For high energy pp collisions, the concepts ''4π'' and ''full acceptance'' are distinct. At the SSC, the appropriate variables for describing phase space are the lego variables: pseudorapidity η and azimuthal angle φ. While most of 4π is covered by pseudorapidities less than 3 or 4 in magnitude, at the SSC there is very interesting physics out to η's of 9 to 12. For over a year I have been attempting to encourage an initiative at the SSC to provide a detector which could cover the missing acceptance of the two big detectors, which in particular have no appreciable charged particle tracking with good momentum resolution beyond rapidities of 2.5 or so. The nonnegotiable criteria for an FAD are for me the following: 1. All charged particles are seen and their momenta measured well, provided pt is not too large. 2. All photons are seen and their momenta are measured well. 3. The physics of rapidity-gaps is not compromised. This means angular coverage from 90 degrees down to tens of microradians. The above criteria cannot be met on day one of SSC commissioning with the amount of funds available. But I believe a staged approach is feasible, with a lot of interesting physics available along the way. The basic philosophy underlying the FAD idea is that it should first and most be a survey instrument, sensitive to almost everything, but optimized for almost nothing. Its strength is in the perception of complex patterns individual events, used as a signature of new and/or interesting physics. Examples of such patterns will be given later

  6. Extraction of Z' coupling data from Z' → jj at the LHC and SSC

    International Nuclear Information System (INIS)

    Rizzo, T.G.

    1993-06-01

    A recent analysis has shown that it may be possible at the SSC to extract information about Z' couplings via the decay Z' → jj. This technique was found to be useful for some extended electroweak models provided the Z' is relatively light. In the present paper, the authors generalize this procedure to the LHC and to Z''s which are more massive than 1 TeV

  7. Model SSC [Superconducting Super Collider] dipole magnet cryostat assembly at Fermilab

    International Nuclear Information System (INIS)

    Niemann, R.C.

    1989-03-01

    The Superconducting Super Collider (SSC) magnet development program includes the design, fabrication and testing of full length model dipole magnets. A result of the program has been the development of a magnet cryostat design. The cryostat subsystems consist of cold mass connection-slide, suspension, thermal shields, insulation, vacuum vessel and interconnections. Design details are presented along with model magnet production experience. 6 refs., 13 figs

  8. ELMUD: An ELectron MUon Detector for Higgs physics at the SSC

    International Nuclear Information System (INIS)

    Paige, F.E.

    1987-01-01

    Requirements for detecting H → Z 0 Z 0 → iota + iota - iota + iota - at the SSC with m/sub H/ = 800 GeV are explored. It is found a luminosity of 10 34 cm -2 sec -1 is needed but that the detector can have only a fast electromagnetic calorimeter plus a muon detector. Such a detector should be feasible at the required luminosity

  9. Thermal optimization of the helium-cooled power leads for the SSC

    International Nuclear Information System (INIS)

    Demko, J.A.; Schiesser, W.E.; Carcagno, R.; McAshan, M.; McConeghy, R.

    1992-01-01

    The optimum thermal design of the power leads for the Superconducting Super Collider (SSC) will minimize the amount of Carnot work (which is a combination of refrigeration and liquefaction work) required. This optimization can be accomplished by the judicious selection of lead length and diameter. Even though an optimum set of dimensions is found, the final design must satisfy other physical constraints such as maximum allowable heat leak and helium vapor mass flow rate. A set of corresponding lengths and diameters has been determined that meets these requirements for the helium vapor-cooled, spiral-fin power lead design of the SSC. Early efforts by McFee and Mallon investigated optimizing power leads for cryogenic applications with no convection cooling. Later designs utilized the boiled-off helium vapor to cool the lead. One notable design for currents up to several thousand amps is presented by Efferson based on a series of recommendations discussed by Deiness. Buyanov presents many theoretical models and design formulae but does not demonstrate an approach to thermally optimizing the design of a vapor-cooled lead. In this study, a detailed numerical thermal model of a power lead design for the SSC has been developed. It was adapted from the dynamic model developed by Schiesser. This model was used to determine the optimum dimensions that minimize the Carnot refrigeration and liquefaction work due to the leads. Since the SSC leads will be cooled by supercritical helium, the flow of vapor is regulated by a control valve. These leads include a superconducting portion at the cold end. All of the material properties in the model are functions of temperature, and for the helium are functions of pressure and temperature. No pressure drop calculations were performed as part of this analysis. The diameter that minimizes the Carnot work was determined for four different lengths at a design current of 6600 amps

  10. SSC type NbTi superconductor research program at Teledyne SC

    International Nuclear Information System (INIS)

    Kallsen, J.F.; McDonald, W.K.; Geno, J.D.; O'Larey, P.M.; Siddall, M.B.

    1991-01-01

    In an on-going research effort at Teledyne SC, several multifilament niobium titanium composite billets have been fabricated and processed to make SSC type wire. Critical current densities of 3000 A/mm 2 ± 5% and 2950 A/mm 2 ± 5% (5 T, 4.2 K, 10 -14 ohm-m) have been achieved in wires containing 6.5 and 4.8 micron diameter filaments respectively. This paper addresses piece length and cable-able characteristics

  11. Test of two 1.8 M SSC model magnets with iterated design

    International Nuclear Information System (INIS)

    Wanderer, P.; Cottingham, J.G.; Dahl, P.

    1989-01-01

    We report results from two 1.8 m-long dipoles built as part of the Superconducting Super Collider (SSC) RandD program. These magnets contain design changes made on both the 1.8 m and the full-length 17 m dipoles to improve quench performance, magnetic field uniformity, and manufacturability. The magnets reach 8 T with little training. 10 refs., 5 figs., 1 tab

  12. Production and detection at SSC of Higgs bosons in left-right symmetric theories

    International Nuclear Information System (INIS)

    Gunion, J.; Kayser, B.; Mohapatra, R.N.; Deshpande, N.G.; Grifols, J.; Mendez, A.; Olness, F.; Pal, P.B.

    1986-12-01

    We discuss the production and detection at SSC of charged and neutral Higgs bosons of the left-right symmetric theories. The H + , which is largely a member of a left-right ''bidoublet,'' should be detectable. The H 2 0 , a more unusual Higgs particle which, apart from mixing, is in a right-handed triplet and does not couple to quarks, may be detectable too

  13. A bipolar monolithic preamplifier for high-capacitance SSC [Superconducting Super Collider] silicon calorimetry

    International Nuclear Information System (INIS)

    Britton, C.L. Jr.; Kennedy, E.J.; Bugg, W.M.

    1990-01-01

    This paper describes a preamplifier designed and fabricated specifically to address the requirements of silicon calorimetry for the Superconducting Super Collider (SSC). The topology and its features are discussed in addition to the design methodology employed. The simulated and measured results for noise, power consumption, and speed are presented. Simulated an measured data for radiation damage effects as well as data for post-damage annealing are also presented. 8 refs., 7 figs., 2 tabs

  14. Advanced forward calorimetry for the SSC and TeVatron collider

    International Nuclear Information System (INIS)

    DiBitonto, D.; Van Peteghem, P.M.; Geiger, R.L.; McIntyre, P.M.; Pang, Y.; Thane, J.M.; White, J.T.; Atac, M.

    1989-01-01

    We describe a project to develop fast, radiation hardened forward calorimetry for the SSC and TeVatron collider. Detector technologies discussed are based on gas and warm liquid media. In particular, we present the design of an ultrasensitive hybrid charge preamplifier for liquid technology capable of operating at 0.1-1 GHz. The actual detector bandwidth will depend on the choice of detector media used and the maximum allowable operating high voltage. (orig.)

  15. A turtle-like swimming robot using a smart soft composite (SSC) structure

    International Nuclear Information System (INIS)

    Kim, Hyung-Jung; Song, Sung-Hyuk; Ahn, Sung-Hoon

    2013-01-01

    This paper describes the development of a biomimetic swimming robot based on the locomotion of a marine turtle. To realize the smooth, soft flapping motions of this type of turtle, a novel actuator was also developed, using a smart soft composite (SSC) structure that can generate bending and twisting motions in a simple, lightweight structure. The SSC structure is a composite consisting of an active component to generate the actuation force, a passive component to determine the twisting angle of the structure, and a matrix to combine the components. The motion of such a structure can be designed by specifying the angle between a filament of the scaffold structure and a shape-memory alloy (SMA) wire. The bending and twisting motion of the SSC structure is explained in terms of classical laminate theory, and cross-ply and angled-ply structures were fabricated to evaluate its motion. Finally, the turtle-like motion of a swimming robot was realized by employing a specially designed SSC structure. To mimic the posterior positive twisting angle of a turtle’s flipper during the upstroke, the SMA wire on the upper side was offset, and a positive ply-angled scaffold was used. Likewise, for the anterior negative twisting angle of the flipper during the downstroke, an offset SMA wire on the lower side and a positive ply-angled scaffold were also required. The fabricated flipper’s length is 64.3 mm and it realizes 55 mm bending and 24° twisting. The resulting robot achieved a swimming speed of 22.5 mm s −1 . (paper)

  16. Passive superconductor: A viable method of controlling magnetization multipoles in the SSC dipole

    International Nuclear Information System (INIS)

    Green, M.A.

    1989-02-01

    At injection, the magnetization of the superconductor produces the dominant field error in the SSC dipole magnets. The field generated by magnetization currents in the superconductor is rich in higher symmetric multipoles (normal sextupole, normal decapole, and so on). Pieces of passive superconductor properly located within the bore of the dipole magnet can cancel the higher multipoles generated by the SSC dipole coils. The multipoles generated by the passive superconductor (predominantly sextupole and decapole) are controlled by the angular and radial location of the superconductor, the volume of superconductor, and the size of the superconducting filaments within the passive conductor. This paper will present the tolerances on each of these factors. The paper will show that multipole correction using passive superconductor is in general immune to the effects of temperature and magnetization decay due to flux creep, provided that dipole superconductor and the passive correction superconductor are properly specified. When combined with a lumped correction system, the passive superconductor can be a viable alternative to continuous correction coils within the SSC dipoles. 20 refs., 8 figs., 2 tabs

  17. Passive superconductor a viable method of controlling magnetization multipoles in the SSC dipole

    International Nuclear Information System (INIS)

    Green, M.A.

    1989-01-01

    At injection, the magnetization of the superconductor produces the dominant field error in the SSC dipole magnets. The field generated by magnetization currents in the superconductor is rich in higher symmetric multipoles (normal sextupole, normal decapole, and so on). Pieces of passive superconductor properly located within the bore of the dipole magnet can cancel the higher multipoles generated by the SSC dipole coils. The multipoles generated by the passive superconductor (predominantly sextupole and decapole) are controlled by the angular and radial location of the superconductor, the volume of superconductor, and the size of the superconducting filaments within the passive conductor. This paper will present the tolerances on each of these factors. The paper will show that multipole correction using passive superconductor is in general immune to the effects of temperature and magnetization decay due to flux creep, provided that dipole superconductor and the passive correction superconductor are properly specified. When combined with a lumped correction system, the passive superconductor can be a viable alternative to continuous correction coils within the SSC dipoles. 20 refs., 8 figs., 2 tabs

  18. Central and Eastern United States (CEUS) Seismic Source Characterization (SSC) for Nuclear Facilities Project

    Energy Technology Data Exchange (ETDEWEB)

    Kevin J. Coppersmith; Lawrence A. Salomone; Chris W. Fuller; Laura L. Glaser; Kathryn L. Hanson; Ross D. Hartleb; William R. Lettis; Scott C. Lindvall; Stephen M. McDuffie; Robin K. McGuire; Gerry L. Stirewalt; Gabriel R. Toro; Robert R. Youngs; David L. Slayter; Serkan B. Bozkurt; Randolph J. Cumbest; Valentina Montaldo Falero; Roseanne C. Perman' Allison M. Shumway; Frank H. Syms; Martitia (Tish) P. Tuttle

    2012-01-31

    This report describes a new seismic source characterization (SSC) model for the Central and Eastern United States (CEUS). It will replace the Seismic Hazard Methodology for the Central and Eastern United States, EPRI Report NP-4726 (July 1986) and the Seismic Hazard Characterization of 69 Nuclear Plant Sites East of the Rocky Mountains, Lawrence Livermore National Laboratory Model, (Bernreuter et al., 1989). The objective of the CEUS SSC Project is to develop a new seismic source model for the CEUS using a Senior Seismic Hazard Analysis Committee (SSHAC) Level 3 assessment process. The goal of the SSHAC process is to represent the center, body, and range of technically defensible interpretations of the available data, models, and methods. Input to a probabilistic seismic hazard analysis (PSHA) consists of both seismic source characterization and ground motion characterization. These two components are used to calculate probabilistic hazard results (or seismic hazard curves) at a particular site. This report provides a new seismic source model. Results and Findings The product of this report is a regional CEUS SSC model. This model includes consideration of an updated database, full assessment and incorporation of uncertainties, and the range of diverse technical interpretations from the larger technical community. The SSC model will be widely applicable to the entire CEUS, so this project uses a ground motion model that includes generic variations to allow for a range of representative site conditions (deep soil, shallow soil, hard rock). Hazard and sensitivity calculations were conducted at seven test sites representative of different CEUS hazard environments. Challenges and Objectives The regional CEUS SSC model will be of value to readers who are involved in PSHA work, and who wish to use an updated SSC model. This model is based on a comprehensive and traceable process, in accordance with SSHAC guidelines in NUREG/CR-6372, Recommendations for Probabilistic

  19. Magnet strength fluctuations in the SSC [Superconducting Super Collider] lattice: Part 2, Frequency modulation

    International Nuclear Information System (INIS)

    Goderre, G.P.

    1987-06-01

    This is a continuation of SSC-N-305. SSC-N-305 examined the effects of field strength modulation, when the modulation frequency (f/sub mod/) was equal to zero (i.e., current offset). The objective of this study is to examine the effect of field strength modulation with modulation frequencies other than zero. To this end, the tracking routine TEAPOT is modified to simulate frequency modulation of the current output from the 10 main SSC magnet power supplies. The amplitude (A/sub i/) and phase (phi/sub i/) of the modulation for the i/sup th/ power supply are chosen randomly. Effects of bore tube shielding are included only when studying 60 Hz modulation frequency. Bore tube shielding is due to the copper coating on the bore tube walls. This coating modifies the amplitude and phase of the modulation inside the bore tube. The bore tube is more effective at shielding the dipole field and it becomes most effective as the modulation frequency increases. 3 refs., 10 figs., 3 tabs

  20. An integrated 3D design, modeling and analysis resource for SSC detector systems

    International Nuclear Information System (INIS)

    DiGiacomo, N.J.; Adams, T.; Anderson, M.K.; Davis, M.; Easom, B.; Gliozzi, J.; Hale, W.M.; Hupp, J.; Killian, K.; Krohn, M.; Leitch, R.; Lajczok, M.; Mason, L.; Mitchell, J.; Pohlen, J.; Wright, T.

    1989-01-01

    Integrated computer aided engineering and design (CAE/CAD) is having a significant impact on the way design, modeling and analysis is performed, from system concept exploration and definition through final design and integration. Experience with integrated CAE/CAD in high technology projects of scale and scope similar to SSC detectors leads them to propose an integrated computer-based design, modeling and analysis resource aimed specifically at SSC detector system development. The resource architecture emphasizes value-added contact with data and efficient design, modeling and analysis of components, sub-systems or systems with fidelity appropriate to the task. They begin with a general examination of the design, modeling and analysis cycle in high technology projects, emphasizing the transition from the classical islands of automation to the integrated CAE/CAD-based approach. They follow this with a discussion of lessons learned from various attempts to design and implement integrated CAE/CAD systems in scientific and engineering organizations. They then consider the requirements for design, modeling and analysis during SSC detector development, and describe an appropriate resource architecture. They close with a report on the status of the resource and present some results that are indicative of its performance. 10 refs., 7 figs

  1. Central and Eastern United States (CEUS) Seismic Source Characterization (SSC) for Nuclear Facilities

    International Nuclear Information System (INIS)

    Coppersmith, Kevin J.; Salomone, Lawrence A.; Fuller, Chris W.; Glaser, Laura L.; Hanson, Kathryn L.; Hartleb, Ross D.; Lettis, William R.; Lindvall, Scott C.; McDuffie, Stephen M.; McGuire, Robin K.; Stirewalt, Gerry L.; Toro, Gabriel R.; Youngs, Robert R.; Slayter, David L.; Bozkurt, Serkan B.; Cumbest, Randolph J.; Falero, Valentina Montaldo; Perman, Roseanne C.; Shumway, Allison M.; Syms, Frank H.; Tuttle, Martitia P.

    2012-01-01

    This report describes a new seismic source characterization (SSC) model for the Central and Eastern United States (CEUS). It will replace the Seismic Hazard Methodology for the Central and Eastern United States, EPRI Report NP-4726 (July 1986) and the Seismic Hazard Characterization of 69 Nuclear Plant Sites East of the Rocky Mountains, Lawrence Livermore National Laboratory Model, (Bernreuter et al., 1989). The objective of the CEUS SSC Project is to develop a new seismic source model for the CEUS using a Senior Seismic Hazard Analysis Committee (SSHAC) Level 3 assessment process. The goal of the SSHAC process is to represent the center, body, and range of technically defensible interpretations of the available data, models, and methods. Input to a probabilistic seismic hazard analysis (PSHA) consists of both seismic source characterization and ground motion characterization. These two components are used to calculate probabilistic hazard results (or seismic hazard curves) at a particular site. This report provides a new seismic source model. Results and Findings The product of this report is a regional CEUS SSC model. This model includes consideration of an updated database, full assessment and incorporation of uncertainties, and the range of diverse technical interpretations from the larger technical community. The SSC model will be widely applicable to the entire CEUS, so this project uses a ground motion model that includes generic variations to allow for a range of representative site conditions (deep soil, shallow soil, hard rock). Hazard and sensitivity calculations were conducted at seven test sites representative of different CEUS hazard environments. Challenges and Objectives The regional CEUS SSC model will be of value to readers who are involved in PSHA work, and who wish to use an updated SSC model. This model is based on a comprehensive and traceable process, in accordance with SSHAC guidelines in NUREG/CR-6372, Recommendations for Probabilistic

  2. Total hydrocarbon content (THC) testing in liquid oxygen (LOX) systems

    Science.gov (United States)

    Meneghelli, B. J.; Obregon, R. E.; Ross, H. R.; Hebert, B. J.; Sass, J. P.; Dirschka, G. E.

    2015-12-01

    The measured Total Hydrocarbon Content (THC) levels in liquid oxygen (LOX) systems at Stennis Space Center (SSC) have shown wide variations. Examples of these variations include the following: 1) differences between vendor-supplied THC values and those obtained using standard SSC analysis procedures; and 2) increasing THC values over time at an active SSC test stand in both storage and run vessels. A detailed analysis of LOX sampling techniques, analytical instrumentation, and sampling procedures will be presented. Additional data obtained on LOX system operations and LOX delivery trailer THC values during the past 12-24 months will also be discussed. Field test results showing THC levels and the distribution of the THC's in the test stand run tank, modified for THC analysis via dip tubes, will be presented.

  3. Total Hydrocarbon Content (THC) Testing in Liquid Oxygen (LOX)

    Science.gov (United States)

    Meneghelli, B. J.; Obregon, R. E.; Ross, H. R.; Hebert, B. J.; Sass, J. P.; Dirschka, G. E.

    2016-01-01

    The measured Total Hydrocarbon Content (THC) levels in liquid oxygen (LOX) systems at Stennis Space Center (SSC) have shown wide variations. Examples of these variations include the following: 1) differences between vendor-supplied THC values and those obtained using standard SSC analysis procedures; and 2) increasing THC values over time at an active SSC test stand in both storage and run vessels. A detailed analysis of LOX sampling techniques, analytical instrumentation, and sampling procedures will be presented. Additional data obtained on LOX system operations and LOX delivery trailer THC values during the past 12-24 months will also be discussed. Field test results showing THC levels and the distribution of the THC's in the test stand run tank, modified for THC analysis via dip tubes, will be presented.

  4. Report of the third meeting of the SSDL Scientific Committee (SSC). Vienna, 19-23 September 1988

    International Nuclear Information System (INIS)

    1988-01-01

    The SSDL Scientific Committee (SSC) was appointed in 1985 by the Director General of the IAEA, in consultation with and the concurrence of the Director General of the WHO. As indicated in its Terms of Reference, the main objective of the SSC is to advise the Directors General of the IAEA and WHO regarding the programme of work of the IAEA/WHO Network of Secondary Standard Dosimetry Laboratories (SSDLs). The first meeting of the SSC was held in May 1986 and the recommendations were reported in IAEA SSDL Newsletter No. 25, October 1986. The second meeting of the SSC was held in June 1987 and the recommendations were reported in the SSDL Newsletter No. 26, October 1987. Discussions and recommendations of this meeting are covered in this report

  5. Improved inter-assembly heat transfer modeling under low flow conditions for the Super System Code (SSC)

    International Nuclear Information System (INIS)

    Horak, W.C.; Guppy, J.G.

    1984-01-01

    The Super System Code (SSC) was developed at the Brookhaven National Laboratory (BNL) for the thermal hydraulic analysis of natural circulation transients, operational transients, and other system wide transients in nuclear power plants. SSC is a generic, best estimate code that models the in-vessel components, heat transport loops, plant protection systems and plant control systems. SSC also simulates the balance of plant when interfaced with the MINET code. SSC has been validated against both numerical and experimental data bases and is now used by several outside users. An important area of interest in LMFBR transient analysis is the prediction of the response of the reactor core under low flow conditions, such as experienced during a natural circulation event. Under these circumstances there are many physical phenomena which must be modeled to provide an adequate representation by a computer code simulation. The present version of SSC contains numerous models which account for most of the major phenomena. However, one area where the present model in SSC is being improved is in the representation of heat transfer and buoyancy effects under low flow operation. To properly improve the present version, the addition of models to represent certain inter-assembly effects is required

  6. Prediction and forecast of Suspended Sediment Concentration (SSC) on the Upper Yangtze basin

    Science.gov (United States)

    Matos, José Pedro; Hassan, Marwan; Lu, Xixi; Franca, Mário J.

    2017-04-01

    Sediment transport in suspension may represent 90% or more of the global annual flux of sediment. For instance, more than 99% of the sediment supplied to the sea by the Yangtze River is suspended load. Suspended load is an important component for understanding channel dynamics and landscape evolution. Sediments transported in suspension are a major source of nutrients for aquatic organisms in riparian and floodplain habitats, and play a beneficial role acting as a sink in the carbon cycle. Excess of fine sediments may also have adverse effects. It can impair fish spawning by riverbed clogging, disturb foraging efficiency of hunting of river fauna, cause algae and benthos scouring, reduce or inhibit exchanges through the hyporheic region. Accumulation of fine sediments in reservoirs reduces storage capacity. Although fine sediment dynamics has been the focus of many studies, the current knowledge of sediment sources, transfer, and storage is inadequate to address fine sediment dynamics in the landscape. The theoretical derivation of a complete model for suspended sediment transport at the basin scale, incorporating small scale processes of production and transport, is hindered because the underlying mechanisms are produced at different non-similar scales. Availability of long-term reliable data on suspended sediment dynamics is essential to improve our knowledge on transport processes and to develop reliable sediment prediction models. Over the last 60 years, the Yangtze River Commission has been measuring the daily Suspended Sediment Concentration (SSC) at the Pingshan station. This dataset provides a unique opportunity to examine temporal variability and controls of fine sediment dynamics in the Upper Yangtze basin. The objective of this study is to describe temporal variation of fine sediment dynamics at the Pingshan station making use of the extensive sediment monitoring program undertaken at that location. We test several strategies of prediction and forecast

  7. Thermal optimization of the helium-cooled power leads for the SSC

    International Nuclear Information System (INIS)

    Demko, J.A.; Schiesser, W.E.; Carcagno, R.; McAshan, M.; McConeghy, R.

    1992-03-01

    The optimum thermal design of the power leads for the Superconducting Super Collider (SSC) will minimize the amount of Carnot work (which is a combination of refrigeration and liquefaction work) required. This optimization can be accomplished by the judicious selection of lead length and diameter. Even though an optimum set of dimensions is found, the final design must satisfy other physical constraints such as maximum allowable heat leak and helium vapor mass flow rate. A set of corresponding lengths and diameters has been determined that meets these requirements for the helium vapor-cooled, spiral-fin power lead design of the SSC. Early efforts by McFee and Mallon investigated optimizing power leads for cryogenic applications with no convection cooling. Later designs utilized the boiled-off helium vapor to cool the lead. One notable design for currents up to several thousand amps is presented by Efferson based on a series of recommendations discussed by Deiness. Buyanov presents many theoretical models and design formulate but does not demonstrate an approach to thermally optimizing the design of a vapor-cooled lead. A method for optimizing superconducting magnet current leads is described by Maehata et al. The approach assumes that the helium boil-off caused by heat conduction along with power lead into the low-temperature helium is used to cool the lead. The optimum solution is found when the heat flow at the cold end is minimized.. In this study, a detailed numerical thermal model of a power lead design for the SSC has been developed. It was adapted from the dynamic model developed by Schiesser. This model was used to determine the optimum dimensions that minimize the Carnot refrigeration and liquefaction work due to the leads

  8. SSC-excited pulsations recorded near noon on GEOS 2 and on the ground (CDAW 6)

    International Nuclear Information System (INIS)

    Wedeken, U.; Voelker, H.; Knott, K.; Lester, M.

    1986-01-01

    The SSC occurring on March 22, 1979, at 0826 UT had an unusually sharp onset in Scandinavia, in Middle Europe and in experiments on the geostationary satellite GEOS 2, which was near noon, local magnetic time. The ground magnetometer stations showed a small preimpuse which started approx.5 s before the main impulse. Both impulses needed approx.2 s to ''propagate'' from ground stations at L = 6.3-4.6. Search coil magnetometers indicate a very small precursor in northern Finland (Lapprox.4.4-6.0) which started approx.15-20 s before the main impulse. This small precursor also occurred close to the time of the SSC onset at GEOS 2. We interpret this precursor as an effect of precipitating electrons changing the ionospheric conductivity in a localized region. The main impulse triggered damped magnetic pulsations (Psc) with periods near 160 s and 50 s visible in northern Scandinavia and the electric field detector on GEOS 2. Furthermore, the magnetic field and the energetic ions at GEOS observed pulsations with periods near 80 s, but these could only be observed at the northernmost ground stations. There are several indications that the first three harmonics of standing hydromagnetic waves are detected. They may correspond to periodic oscillations of the subsolar point or eigenperiods of the SSC-excited fast mode (compressional cavity resonance). The tentatively identified second harmonic wave (period approx.80 s) is indicative of a bounce resonance of ring current protons. Inside the plasmasphere the dominant period of a superimposed Psc 4 event increased with latitude for the H component indicating several toroidal eigenoscillations

  9. Simulation of the SSC refrigeration system using the ASPEN/SP process simulator

    International Nuclear Information System (INIS)

    Rasson, J.; Dweck, J.

    1990-01-01

    The SSC Magnet must be maintained at a superconducting temperature of 4 K. The proposed refrigeration cooling processes consist of fairly simple closed cycles which take advantage of the Joule-Thompson effect via a series of expansions and compressions of helium gas which has been precooled by liquid nitrogen. The processes currently under consideration consist of three cycles, the 20 K shield cooling, the 4.0 K helium refrigerator and the helium liquefier. The process units which are to be employed are compressors, turbines, expanders, mixers, flashes, two stream heat exchangers and multiple stream heat exchangers. The cycles are to be operated at or near steady state. Due to the large number of competing cooling sector designs to be considered and the high capital and operating costs of the proposed processes, the SSC Laboratory requires a software tool for the validation and optimization of the individual designs and for the performance of cost-benefit analyses among competing designs. Since these processes are steady state flow processes involving primarily standard unit operations, a decision was made to investigate the application of a commercial process simulator to the task. Several months of internal evaluations by the SSC Laboratory revealed that while the overall structure and calculation approach of a number of the commercial simulators were appropriate for this task, all were lacking essential capabilities in the areas of thermodynamic property calculations for cryogenic systems and modeling of complex, multiple stream heat exchangers. An acceptable thermodynamic model was provided and a series of simple, but three software vendors. Based on the results of the benchmark tests, the ASPEN/SP process simulator was selected for future modeling work. 2 refs., 4 figs

  10. Underground facility for geoenvironmental and geotechnical research at the SSC Site in Texas

    International Nuclear Information System (INIS)

    Wang, H.F.; Myer, L.R.

    1994-01-01

    The subsurface environment is an important national resource that is utilized for construction, waste disposal and groundwater supply. Conflicting and unwise use has led to problems of groundwater contamination. Cleanup is often difficult and expensive, and perhaps not even possible in many cases. Construction projects often encounter unanticipated difficulties that increase expenses. Many of the difficulties of predicting mechanical behavior and fluid flow and transport behavior stem from problems in characterizing what cannot be seen. An underground research laboratory, such as can be developed in the nearly 14 miles of tunnel at the Superconducting Super Collider (SSC) site, will provide a unique opportunity to advance scientific investigations of fluid flow, chemical transport, and mechanical behavior in situ in weak and fractured, porous rock on a scale relevant to civil and environmental engineering applications involving the subsurface down to a depth of 100 m. The unique element provided by underground studies at the SSC site is three-dimensional access to a range of fracture conditions in two rock types, chalk and shale. Detailed experimentation can be carried out in small sections of the SSC tunnel where different types of fractures and faults occur and where different rock types or contacts are exposed. The entire length of the tunnel can serve as an observatory for large scale mechanical and fluid flow testing. The most exciting opportunity is to mine back a volume of rock to conduct a post-experiment audit following injection of a number of reactive and conservative tracers. Flow paths and tracer distributions can be examined directly. The scientific goal is to test conceptual models and numerical predictions. In addition, mechanical and hydrological data may be of significant value in developing safe and effective methods for closing the tunnel itself

  11. Simulation of the SSC [Superconducting Super Collider] refrigeration system using the ASPEN/SP process simulator

    International Nuclear Information System (INIS)

    Rasson, J.; Dweck, J.

    1990-08-01

    The SSC Magnet must maintain at a super conducting temperature of 4 K. The proposed refrigeration cooling processes consist of fairly simple closed cycles which take advantage of the Joule-Thompson effect via a series of expansions and compressions of helium gas which has been precooled by liquid nitrogen. The processes currently under consideration consist of three cycles, the 20 K shield cooling, the 45 K helium refrigerator and the helium liquefier. The process units which are to be employed are compressors, turbines, expanders, mixers, flashes, two stream heat exchangers and multiple stream heat exchangers. The cycles are to be operated at or near steady state. Due to the large number of competing cooling sector designs to be considered and the high capital and operating costs of the proposed processes, the SSC Laboratory requires a software tool for the validation and optimization of the individual designs and for the performance of cost-benefit analyses among competing designs. Since these processes are steady state flow processes involving primarily standard unit operations, a decision was made to investigate the application of a commercial process simulator to the task. Several months of internal evaluations by the SSC Laboratory revealed that while the overall structure and calculation approach of number of the commercial simulators were appropriate for this task, all were lacking essential capabilities in the areas of thermodynamic property calculations for cryogenic systems and modeling of complex, multiple stream heat exchangers. An acceptable thermodynamics model was provided and a series of simple, but representative benchmark problems developed. The model and problems were provided to three software vendors. Based on the results of the benchmark test, the ASPEN/SP process simulator was selected for future modeling work

  12. Multiple coil pulsed magnetic resonance method for measuring cold SSC dipole magnet field quality

    International Nuclear Information System (INIS)

    Clark, W.G.; Moore, J.M.; Wong, W.H.

    1990-01-01

    The operating principles and system architecture for a method to measure the magnetic field multipole expansion coefficients are described in the context of the needs of SSC dipole magnets. The operation of an 8-coil prototype system is discussed. Several of the most important technological issues that influence the design are identified and the basis of their resolution is explained. The new features of a 32-coil system presently under construction are described, along with estimates of its requirements for measurement time and data storage capacity

  13. SSC string test facility for superconducting magnets: Testing capabilities and program for collider magnets

    International Nuclear Information System (INIS)

    Kraushaar, P.; Burgett, W.; Dombeck, T.; McInturff, A.; Robinson, W.; Saladin, V.

    1993-05-01

    The Accelerator Systems String Test (ASST) R ampersand D Testing Facility has been established at the SSC Laboratory to test Collider and High Energy Booster (HEB) superconducting magnet strings. The facility is operational and has had two testing periods utilizing a half cell of collider prototypical magnets with the associated spool pieces and support systems. This paper presents a description of the testing capabilities of the facility with respect to components and supporting subsystems (cryogenic, power, quench protection, controls and instrumentation), the planned testing program for the collider magnets

  14. Development of the SSC [Superconducting Super Collider] trim coil beam tube assembly

    International Nuclear Information System (INIS)

    Skaritka, J.; Kelly, E.; Schneider, W.

    1987-01-01

    The Superconducting Super Collider uses ≅9600 dipole magnets. The magnets have been carefully designed to exhibit minimal magnetic field harmonics. However, because of superconductor magnetization effects, iron saturation and conductor/coil positioning errors, certain harmonic errors are possible and must be corrected by use of multipole correctors called trim coils. For the most efficient use of axial space in the magnet, and lowest possible current, a distributed internal correction coil design is planned. The trim coil assembly is secured to the beam tube, a uhv tube with special strength, size, conductivity and vacuum. The report details the SSC trim coil/beam tube assembly specifications, history, and ongoing development

  15. Super slow extraction at the SSC using channeling in a curved crystal

    International Nuclear Information System (INIS)

    Newberger, B.S.; Ellison, J.A.

    1991-10-01

    The possibility of a high-precision B-physics experiment in a fixed target configuration has stimulated considerable interest in the extraction of a low-intensity proton beam from the SSC during collider operation. The candidate scheme which has received the most attention uses a bent crystal of Si to deflect protons into the extraction line. In this paper, we present results on deflecting efficiency of Si(110) planes and on the feeding of the crystal by controlled injection of noise into the collider rf system. These results are important in establishing the viability of simultaneous collider and fixed target operation. 21 refs., 4 figs

  16. Structural performance of the first SSC [Superconducting Super Collider] Design B dipole magnet

    International Nuclear Information System (INIS)

    Nicol, T.H.

    1989-09-01

    The first Design B Superconducting Super Collider (SSC) dipole magnet has been successfully tested. This magnet was heavily instrumented with temperature and strain gage sensors in order to evaluate its adherence to design constraints and design calculations. The instrumentation and associated data acquisition system allowed monitoring of the magnet during cooldown, warmup, and quench testing. This paper will focus on the results obtained from structural measurements on the suspension system during normal and rapid cooldowns and during quench studies at full magnet current. 4 refs., 9 figs

  17. Results of heater induced quenches on a 1-m SSC model dipole

    International Nuclear Information System (INIS)

    Hassenzahl, W.V.

    1985-10-01

    This report describes the results of a series of heater induced quenches on the 1-m long SSC model dipole D-12C-7 constructed at LBL. Test results of the following types are described: quench propagation velocities - axial; quench propagation velocities - transverse; and rate of temperature rise in the conductor. The primary purpose of these tests was to measure quench velocities at a variety of locations and for several currents/fields which can be used to refine the quench predictions for longer magnets. Because of limited data in the low field region of this magnet, it is recommended that it be retested with additional voltage taps. 20 figs., 6 tabs

  18. Transversely-biased ferrite-tuned cavity for the SSC booster

    International Nuclear Information System (INIS)

    Carlini, R.D.; Friedrichs, C. Jr.; Thiessen, H.A.

    1985-01-01

    Ferrite tuning of rf cavities is used to provide the change in frequency necessary as the velocity of particles in synchrotrons increases. A new technique in which the ferrite bias field is applied in a direction perpendicular to the rf field offers the possibility of greatly reducing the rf power dissipation in the ferrite. A possible 60 MHz design is discussed for the SSC booster. The cavity design is based on a simple coaxial quarter-wave resonator. A brief discussion is given fo the theory of perpendicular biasing. The measured electric Q's of five different microwave-type ferrite samples are reported and compared with the manufacturer's specifications. 9 fig

  19. Radiation effects on JFETS, MOSFETS, and bipolar transistors, as related to SSC circuit design

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, E J; Gray, B; Wu, A [Dept. of Electrical and Computer Engineering, Univ. of Tennessee, Knoxville, TN (United States); Alley, G T; Britton, Jr, C L [Oak Ridge National Lab., TN (United States); Skubic, P L [Univ. of Oklahoma, Dept. of Physics and Astronomy, Norman, OK (United States)

    1991-10-01

    Some results of radiation effects on selected junction field-effect transistors, MOS field-effect transistors, and bipolar junction transistors are presented. The evaluations include dc parameters, as well as capacitive variations and noise evaluations. The tests are made at the low current and voltage levels (in particular at currents {<=} 1 mA) that are essential for the low-power regimes required by SSC circuitry. Detailed noise data are presented both before and after 5-Mrad (gamma) total-dose exposure. SPICE radiation models for three high-frequency bipolar processes are compared for a typical charge-sensitive preamplifier. (orig.).

  20. Effect of prestress on performance of a 1.8 m SSC R ampersand D dipole

    International Nuclear Information System (INIS)

    Wanderer, P.; Anerella, M.; Cottingham, G.; Ganetis, G.; Garber, M.; Ghosh, A.; Greene, A.; Gupta, R.; Herrera, J.; Kahn, S.; Kelly, E.; Meade, A.; Morgan, G.; Muratore, J.; Prodell, A.; Rehak, M.; Rohrer, E.; Sampson, W.; Shutt, R.; Thompson, P.; Willen, E.; Goodzeit, C.

    1991-01-01

    A series of 1.8 SSC dipoles is being built and tested as part of the R ampersand D program. One of the 40 mm - aperture magnets was tested with a standard assembly and then reassembled and retested in a special configuration which had significantly less azimuthal prestress than the initial assembly. We report quench, coil stress, end force, and harmonics data for each of the assemblies. Quench performance was not degraded for the low-prestress assembly. 4 refs., 5 figs., 5 tabs

  1. Overview of a robotic system for azimuthal dimensions of SSC dipole coils

    International Nuclear Information System (INIS)

    Assell, D.L.; Cahill, J.M.; Carson, J.A.; Connolly, D.F.; Pawlak, S.K.; Rihel, R.K.; Robatzek, W.R.; Robotham, W.F.; Skweres, T.M.; Schmitz, E.; Sims, R.; Ullmark, R.

    1992-01-01

    This system measures the azimuthal dimensions of SSC dipole long coils automatically, taking over 500 measurements in less than four hours. These measurements are then analyzed and displayed via software reports which reveal coil statistics, point by point dimensional graphics, modulus of elasticity measurements, comparisons with previous coils and pre-collaring shimming information. The rapid turnaround of this system yields the ability to spot process variables and fine tune the fabrication techniques. This process will aid in producing coils to the required precision

  2. Analysis of postulated unscrammed loss of flow in SAFR using SSC

    International Nuclear Information System (INIS)

    Slovik, G.C.; Van Tuyle, G.J.

    1988-01-01

    Brookhaven National Laboratory is providing technical assistance to the US Nuclear Regulatory Commission in reviewing two advanced liquid-metal reactor (LMR) designs in order to address the licensability of these innovative concepts. The designs, PRISM and SAFR are being proposed by General Electric Company and Rockwell International (RI), respectively. Brookhaven National Laboratory has utilized the super system code (SSC) to independently evaluate the LMR reactor system response during several postulated unscrammed events. This paper describes the SAFR reactor responses to a beyond-design base event where forced cooling is lost. A similar transient analysis has already been reported for PRISM

  3. Conceptual design of signal cable feedthrus for an SSC proposed Liquid Argon Calorimeter

    International Nuclear Information System (INIS)

    Pope, W.; Watt, R.; Weidenbach, R.; Fong, M.; Bintinger, D.; Abrams, G.; Unno, Y.

    1991-03-01

    Fast, low noise readout, high channel counts, and physical space, length, and heat leak constraints on signal cables for Liquid Argon Calorimeters (LAC) for SSC Detectors impose stringent requirements on the performance and reliability of its cryogenic feedthrus. We present the design status of a configuration currently under study for the Solenoidal Detector Collaboration's LAC Detector option. The report includes LAr-to-vacuum leak mitigation, warm cable conduction intercept means, and heat leak estimates for a 1900 pin, hermetic feedthru plate design. 12 refs., 4 figs., 2 tabs

  4. Motivation for an SSC detector with ultra-high resolution photon detection

    International Nuclear Information System (INIS)

    Gunion, J.F.; Kane, G.

    1992-01-01

    It is well known that incorporating ultra-high resolution photon detection into a general purpose detector for the SSC will be extremely difficult. The authors will argue that the physics signals that could be missed without such resolution are of such importance that a special purpose detector designed specifically for photon final state modes should be constructed, if sufficient resolution cannot be achieved with general purpose detectors. The potentially great value of these signals as a probe of extremely high mass scales is stressed

  5. Methodology and analysis of production safety during Pu recycling at SSC RF RIAR

    International Nuclear Information System (INIS)

    Kirillovich, A.P.

    2000-01-01

    The methodology and criteria for estimating safety in technological processes of the nuclear fuel cycle (NFC) are proposed, substantiated and verified during the large-scale Pu recycling (500 kg). The comprehensive investigation results of the radiation-ecological situation are presented during pilot production of the mixed uranium-plutonium fuel and fuel assembly at SSC RF RIAR. The methodology and experimental data bank can be used while estimating safety in the industrial recycling of Pu and minor-actinides (Np, Am, Cm) in NFC. (author)

  6. SSC-EKE: Semi-Supervised Classification with Extensive Knowledge Exploitation.

    Science.gov (United States)

    Qian, Pengjiang; Xi, Chen; Xu, Min; Jiang, Yizhang; Su, Kuan-Hao; Wang, Shitong; Muzic, Raymond F

    2018-01-01

    We introduce a new, semi-supervised classification method that extensively exploits knowledge. The method has three steps. First, the manifold regularization mechanism, adapted from the Laplacian support vector machine (LapSVM), is adopted to mine the manifold structure embedded in all training data, especially in numerous label-unknown data. Meanwhile, by converting the labels into pairwise constraints, the pairwise constraint regularization formula (PCRF) is designed to compensate for the few but valuable labelled data. Second, by further combining the PCRF with the manifold regularization, the precise manifold and pairwise constraint jointly regularized formula (MPCJRF) is achieved. Third, by incorporating the MPCJRF into the framework of the conventional SVM, our approach, referred to as semi-supervised classification with extensive knowledge exploitation (SSC-EKE), is developed. The significance of our research is fourfold: 1) The MPCJRF is an underlying adjustment, with respect to the pairwise constraints, to the graph Laplacian enlisted for approximating the potential data manifold. This type of adjustment plays the correction role, as an unbiased estimation of the data manifold is difficult to obtain, whereas the pairwise constraints, converted from the given labels, have an overall high confidence level. 2) By transforming the values of the two terms in the MPCJRF such that they have the same range, with a trade-off factor varying within the invariant interval [0, 1), the appropriate impact of the pairwise constraints to the graph Laplacian can be self-adaptively determined. 3) The implication regarding extensive knowledge exploitation is embodied in SSC-EKE. That is, the labelled examples are used not only to control the empirical risk but also to constitute the MPCJRF. Moreover, all data, both labelled and unlabelled, are recruited for the model smoothness and manifold regularization. 4) The complete framework of SSC-EKE organically incorporates multiple

  7. A unified approach to building accelerator simulation software for the SSC

    International Nuclear Information System (INIS)

    Paxson, V.; Aragon, C.; Peggs, S.; Saltmarsh, C.; Schachinger, L.

    1989-03-01

    To adequately simulate the physics and control of a complex accelerator requires a substantial number of programs which must present a uniform interface to both the user and the internal representation of the accelerator. If these programs are to be truly modular, so that their use can be orchestrated as needed, the specification of both their graphical and data interfaces must be carefully designed. We describe the state of such SSC simulation software, with emphasis on addressing these uniform interface needs by using a standardized data set format and object-oriented approaches to graphics and modeling. 12 refs

  8. Combustibility of tetraphenylborate solids

    International Nuclear Information System (INIS)

    Walker, D.D.

    1989-01-01

    Liquid slurries expected under normal in-tank processing (ITP) operations are not ignitible because of their high water content. However, deposits of dry solids from the slurries are combustible and produce dense, black smoke when burned. The dry solids burn similarly to Styrofoam and more easily than sawdust. It is the opinion of fire hazard experts that a benzene vapor deflagration could ignite the dry solids. A tetraphenylborate solids fire will rapidly plug the waste tank HEPA ventilation filters due to the nature of the smoke produced. To prevent ignition and combustion of these solids, the waste tanks have been equipped with a nitrogen inerting system

  9. Burden to importance ratio as a quantitative measure to validate the RISC-3 SSC in OPTION-2

    International Nuclear Information System (INIS)

    Ha, J. S.; Sung, P. H.

    2004-01-01

    A Risk-Informed Safety Significance Categorization (RISSC) is to categorize structures, systems, or components (SSCs) of a Nuclear Power Plant (NPP) into two or more groups, according to their safety significance using both probabilistic and deterministic insights. Recently, OPTION-2 (which is an emerging risk-informed paradigm) recommends that SSCs should be categorized into four groups according to whether they are safety-related or not as well as their safety significance. With the change of 10 CFR 50, safety-related components which categorized into low safety significant SSC (RISC-3 SSC) can be exempted from the existing conservative requirements. Consequently, as OPTION-2 paradigm is applied, a validation process focused on the RISC-3 SSC is needed to assure the categorization results, because most of existing RISSC methods focused on the categorization of the whole SSCs of NPPs based on importance measures obtained from probabilistic and deterministic insights. In this work, Burden to Importance Ratio (BIR) is utilized as a measure for the validation of RISC-3 SSC in OPTION-2. To demonstrate the usefulness of the proposed approach, the approach is applied to 22 components selected from 512 In-Service Test (IST) components of Ulchin unit 3. The results of the application show that the proposed approach is useful for the validation of RISC-3 SSC in OPTION-2

  10. Preliminary study of an integral harmonic analysis magnetic field measurement system for long SSC magnets

    International Nuclear Information System (INIS)

    Green, M.I.

    1991-04-01

    We described the research and development required to design and build a prototype system capable of making integrated magnetic multipole measurements of warm and cryogenic 50 mm bore SSC dipole and quadrupole magnets utilizing a warm probe in a warm finger. Our experience and some preliminary studies indicate that it is highly unlikely that a 16 meter long probe can be fabricated that will have a twist below several milliradians at any temperature. Consequently we describe a segmented 16 meter long probe for which we intend to calibrate the phase of each segment to within 0.1 milliradians. The data for all segments will be acquired simultaneously, and integrated data will be generated from the vector sums of the individual segments. The calibration techniques and instrumentation required to implement this system are described. The duration of an integral measurement at one current is less than ten seconds, which is three orders of magnitude shorter than that required by the mole technique presently being used. The system is based on an extrapolation of the techniques used at LBL to measure cryogenic 1 meter models of SSC magnets with a cryogenic probe. 3 refs., 3 figs

  11. Hydrodynamic calculations of 20-TeV beam interactions with the SSC beam dump

    International Nuclear Information System (INIS)

    Wilson, D.C.; Wingate, C.A.; Goldstein, J.C.; Godwin, R.P.; Mokhov, N.V.

    1993-01-01

    The 300μs, 400 MJ SSC proton beam must be contained when extracted to the external beam dump. The current design for the SSC beam dump can tolerate the beat load produced if the beam is deflected into a raster scan over the face of the dump. If the high frequency deflecting magnet were to fail, the beam would scan a single strip across the dump face resulting in higher local energy deposition. This could vaporize some material and lead to high pressures. Since the beam duration is comparable to the characteristic time of expected hydrodynamic motions, we have combined the static energy deposition capability of the MARS computer code with the two- and three-dimensional hydrodynamics of the MBA and SPHINX codes. EOS data suggest an energy deposition threshold of 15 kJ/g, below which hydrodynamic effects are minimal. Above this our 2D calculations show a hole boring rate of 7 cm/μs for the nominal beam, and pressures of a few kbar. Scanning the nominal beam faster than 0.08 cm/μs should minimize hydrodynamic effects. 3D calculations support this

  12. Collarless, close-in, shaped iron aperture designs for the SSC [Superconducting Super Collider] dipole

    International Nuclear Information System (INIS)

    Gupta, R.C.; Morgan, G.H.

    1989-01-01

    The nominal-design SSC (Superconducting Super Collider) dipole encloses the coil in an iron yoke having a circular aperture. The radial gap between the coil and the iron is about 15 mm to provide space for a strong annular collar around the coil, and also to reduce the effects of iron saturation on central field harmonics. The 15 mm gap also reduces the desirable dipole field contributed by the iron. The present paper gives a coil and aperture configuration in which the gap is reduced to 5 mm at the midplane, in which the aperture is shaped to reduce the unwanted effects of iron saturation. The transfer function is increased about 5% at 6.6 Tesla and the unwanted harmonics are within SSC tolerances at all field levels. These designs would require that the yoke and containment vessel absorb the stresses due to assembly and magnetic forces. A short magnet is being built with a close-in shaped iron aperture and existing coil geometry to assess the benefits of this concept. 7 refs., 3 figs., 6 tabs

  13. A dynamic model for beam tube vacuum effects on the SSC cryogenic system

    International Nuclear Information System (INIS)

    Carcagno, R.H.; Schiesser, W.E.; Shih, H.J.; Xu, X.; Yuecel, A.

    1992-01-01

    The dynamic interaction between the beam-gas scattering induced energy deposition and the SSC cryogenic system is studied by integrating a cryogenic system dynamic simulator with an adsorption model and a beam-gas scattering and energy deposition model. Simulation results are obtained for a 1km long SSC arc section where the beam tube pressure in one of the dipoles is increased up to 150 times its nominal operating pressure. The beam-gas scattering induced heat loads arising from such high pressure perturbations can be very high locally but do not overload the cryogenic system. They are more likely to induce a magnet quench as they result in coil temperatures that largely exceed the desired operating limit. Simulations are also carried out for the case where a large external heat load of 1W/m is imposed on the coldmass of a half-cell in the section. Results show that the coldmass temperatures rise significantly with the added heat load but the energy deposition in the cold mass due to beam-gas scattering remains low despite the increase in the beam tube temperature

  14. A dynamic model for beam tube vacuum effects on the SSC cryogenic system

    International Nuclear Information System (INIS)

    Carcagno, R.H.; Schiesser, W.E.; Shih, H.J.; Xu, X.; Yuecel, A.

    1992-03-01

    The dynamic interaction between the beam-gas scattering induced energy deposition and the SSC cryogenic system is studied by integrating a cryogenic system dynamic simulator with an adsorption model and a beam-gas scattering and energy deposition model. Simulation results are obtained for a 1 km long SSC arc section where the beam tube pressure in one of the dipoles in increased up to 150 times its nominal operating pressure. The beam-gas scattering induced heat loads arising from such high pressure perturbations can be very locally but do not overload the cryogenic system. They are more likely to induce a magnet quench as they result in coil temperatures that largely exceed the desired operating limit. Simulations are also carried out for the case where a large external heat load of 1 W/m is imposed on the coldmass of a half-cell in the section. Results show that the coldmass temperatures rise significantly with the added heat load but the energy deposition in the coldmass due to beam-gas scattering remains low despite the increase in the beam tube temperature

  15. Investigation of factors affecting the calibration of strain gage based transducers (''Goodzeit gages'') for SSC magnets

    International Nuclear Information System (INIS)

    Davidson, M.; Gilbertson, A.; Dougherty, M.

    1991-03-01

    These transducers are designed to measure stresses on SSC collared coils. They are individually calibrated with a bonded ten-stack of SSC inner coil cable by applying a known load and reading corresponding output from the gages. The transducer is supported by a notched ''backing plate'' that allows for bending of the gage beam during calibration or in use with an actual coil. Several factors affecting the calibration and use of the transducers are: the number of times a ''backing plate'' is used, the similarities or difficulties between bonded ten-stacks, and the differences between the ten-stacks and the coil they represent. The latter is probably the most important because a calibration curve is a model of how a transducer should react within a coil. If the model is wrong, the calibration curve is wrong. Information will be presented regarding differences in calibrations between Brookhaven National Labs (also calibrating these transducers) and Fermilab -- what caused these differences, the investigation into the differences between coils and ten-stacks and how they relate to transducer calibration, and some suggestions for future calibrations

  16. Teaching English Idioms through Mnemonic Devices at SSC Level in Pakistan

    Directory of Open Access Journals (Sweden)

    Sidra Mahmood

    2014-03-01

    Full Text Available This research dealt with teaching English idioms through mnemonic devices at SSC level in a school in pakistan. As the students in Pakistan, especially at SSC level, have a habit to learn idioms by rote and face many problems due the technique, the problem was selected for the investigation. Needs Analysis Questionnaire was used to determine the needs and problems faced by the students and their expectations for solution to the problem. Understanding the problems faced by the students in English idioms, an alternative methodology was selected in the form of mnemonic devices and the selected students were taught using the methodology to test its effectiveness in not only teaching English idioms but also making learning motivating, interesting and learner-involving. A post-test was given to understand the effect (if any of the selected alternative method of mnemonics and it was observed that teaching English idioms through mnemonic devices not only helped the learners but also helped in sharpening their memory.

  17. Proposal for a cryogenic magnetic field measurement system for SSC dipole magnets

    International Nuclear Information System (INIS)

    Green, M.I.; Hansen, L.

    1991-03-01

    This proposal describes the research and development required, and the subsequent fabrication of, a system capable of making integrated magnetic multipole measurements of cryogenic 40-mm-bore SSC dipole magnets utilizing a cryogenic probe. Our experience and some preliminary studies indicate that it is highly unlikely that a 16-meter-long probe can be fabricated that will have a twist below several milliradians at cryogenic temperatures. We would anticipate a twist of several milliradians just as a result of cooldown stresses. Consequently, this proposal describes a segmented 16-meter-long probe, for which we intend to calibrate the phase of each segment to within 0.1 milliradians. The data for all segments will be acquired simultaneously, and integrated data will be generated from the vector sums of the individual segments. The calibration techniques and instrumentation required to implement this system will be described. The duration of an integral measurement at one current is expected to be under 10 seconds. The system is based on an extrapolation of the techniques used at LBL to measure cryogenic 1-meter models of SSC magnets with a cryogenic probe. It should be noted that the expansion of the dipole bore from 40 to 50 mm may make a warm-finger device practical at a cost of approximately one quarter of the cryogenic probe. A warm quadrupole measurement system can be based upon the same principles. 5 refs., 9 figs., 1 tab

  18. The quality assurance of superconducting wire and cable for SSC magnets

    International Nuclear Information System (INIS)

    Pollock, D.; Baggett, P.; Capone, D.

    1991-03-01

    The success of the SSC depends on the consistency and uniformity of the superconducting magnets used in the main collider rings and the high energy booster. To a great extent the success of the magnets depends upon the quality of the superconductor wire and cable used in coil windings. As the SSC project has begun its transition from Research to Development, a new laboratory organization has been established to carry the design requirements from concept to reality. The SSCL Magnet Systems Division Quality Assurance Group has been working on the development of a quality management and analysis system for insuring superconductor uniformity through the understanding and control of manufacturing variation. Key areas of the QA activity include: the design and development of a computer database and analysis system for the collection and statistical analysis of superconductor materials data (containing: source physical and chemical properties, billet process history, and final product performance data); and the development of wire and cable product specifications which focus on the control of variation. As a result of this work several new concepts have been developed which will affect the traditional approach to superconductor wire and cable production. 18 refs., 5 figs., 1 tab

  19. Fixed-target particle fluxes and radiation levels at SSC energies

    International Nuclear Information System (INIS)

    Dukes, E.C.

    1993-01-01

    The author calculates the charged particle fluxes and radiation doses from minimum ionizing particles (MIP), electromagnetic showers, and hadronic showers, in a fixed-target experiment at the SSC. This work follows the work of Groom, essentially boosting his results into the laboratory frame. The radiation in dense matter, such as a calorimeter, is produced by several sources: electromagnetic showers, hadronic showers, and minimum ionizing particles. The author does not consider other sources of radiation such as beam halo, a dependent effects, and low energy neutrons from secondary sources. Nor does he consider the effects of magnetic fields. Low energy neutrons have been shown to be an important source of radiation for collider experiments at the SSC. In fixed-target experiments, where the spectrometer is more open and where most detector elements are far away from secondary particle dumps, these sources are not as important. They are also very much detector and experimental hall dependent. Hence the results presented here are only a lower limit of the estimated radiation dose

  20. Access to care for children and young people diagnosed with localized scleroderma or juvenile SSc in the UK.

    Science.gov (United States)

    Hawley, Daniel P; Baildam, Eileen M; Amin, Tania S; Cruikshank, Mary K; Davidson, Joyce E; Dixon, Jennifer; Martin, Neil S; Ohlsson, Victoria; Pilkington, Clarissa; Rangaraj, Satyapal; Riley, Philip; Sundaramoorthy, Chitra; Walsh, Jo; Foster, Helen E

    2012-07-01

    To describe pathways of care and referral to paediatric rheumatology from onset of first symptom (noticed by the patient or their family) to diagnosis for children and young people diagnosed with localized scleroderma (LS) or juvenile SSc (jSSc). Retrospective case note audit of patients under paediatric rheumatology care who presented during January 2005-January 2010. Data included disease subtype, sex, age at key points in the referral pathway and health care professional (HCP) contact. All patient and HCP data were pseudo-anonymized in accordance with good clinical practice. Data were from eight UK centres that saw 89 cases: 62 females, 26 males; 73 LS, 16 jSSc. Median time from first symptom to first HCP review was 4 (range 0-72) months (LS) and 1 (range 0-50) month (jSSc). Median time from first symptom to paediatric rheumatology review was 15 (range 1-103) months (LS) and 7 (range 0-50) months (jSSc). Median time from first HCP review to first paediatric rheumatology review was 11 (range 0-103) months (LS) and 2 (range 0-10) months. First HCP seen (74%) was usually a general practitioner. The referring HCP to paediatric rheumatology was usually a dermatologist (56%) for LS. Median time from first symptom to diagnosis was 13 (range 1-102) months (LS) and 8 (range 1-50) months (jSSc). A prolonged interval occurs from first symptom to definitive diagnosis, which may adversely affect outcome. There is a need to raise awareness of this rare diagnosis and facilitate earlier recognition.

  1. Energy properties of solid fossil fuels and solid biofuels

    International Nuclear Information System (INIS)

    Holubcik, Michal; Jandacka, Jozef; Kolkova, Zuzana

    2016-01-01

    The paper deals about the problematic of energy properties of solid biofuels in comparison with solid fossil fuels. Biofuels are alternative to fossil fuels and their properties are very similar. During the experiments were done in detail experiments to obtain various properties of spruce wood pellets and wheat straw pellets like biofuels in comparison with brown coal and black coal like fossil fuels. There were tested moisture content, volatile content, fixed carbon content, ash content, elementary analysis (C, H, N, S content) and ash fusion temperatures. The results show that biofuels have some advantages and also disadvantages in comparison with solid fossil fuels.

  2. Energy properties of solid fossil fuels and solid biofuels

    Energy Technology Data Exchange (ETDEWEB)

    Holubcik, Michal, E-mail: michal.holubcik@fstroj.uniza.sk; Jandacka, Jozef, E-mail: jozef.jandacka@fstroj.uniza.sk [University of Žilina, Faculty of Mechanical Engineering, Department of Power Engineering, Univerzitná 8215/1, 010 26 Žilina (Slovakia); Kolkova, Zuzana, E-mail: zuzana.kolkova@rc.uniza.sk [Research centre, University of Žilina, Univerzitna 8215/1, 010 26 Žilina (Slovakia)

    2016-06-30

    The paper deals about the problematic of energy properties of solid biofuels in comparison with solid fossil fuels. Biofuels are alternative to fossil fuels and their properties are very similar. During the experiments were done in detail experiments to obtain various properties of spruce wood pellets and wheat straw pellets like biofuels in comparison with brown coal and black coal like fossil fuels. There were tested moisture content, volatile content, fixed carbon content, ash content, elementary analysis (C, H, N, S content) and ash fusion temperatures. The results show that biofuels have some advantages and also disadvantages in comparison with solid fossil fuels.

  3. Effects of solid-state fermentation with two filamentous fungi on the total phenolic contents, flavonoids, antioxidant activities and lipid fractions of plum fruit (Prunus domestica L.) by-products.

    Science.gov (United States)

    Dulf, Francisc Vasile; Vodnar, Dan Cristian; Socaciu, Carmen

    2016-10-15

    Evolutions of phenolic contents and antioxidant activities during solid-state fermentation (SSF) of plum pomaces (from the juice industry) and brandy distillery wastes with Aspergillus niger and Rhizopus oligosporus were investigated. The effect of fermentation time on the oil content and major lipid classes in the plum kernels was also studied. Results showed that total phenolic (TP) amounts increased by over 30% for SSF with Rhizopus oligosporus and by >21% for SSF with A. niger. The total flavonoid contents presented similar tendencies to those of the TPs. The free radical scavenging activities of methanolic extracts were also significantly enhanced. The HPLC-MS analysis showed that quercetin-3-glucoside was the major phenolic compound in both fermented plum by-products. The results also demonstrated that SSF not only helped to achieve higher lipid recovery from plum kernels, but also resulted in oils with better quality attributes (high sterol ester and n-3 PUFA-rich polar lipid contents). Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Determination of the linear aperture of the SSC [Superconducting Supercollider] clustered lattice used for the conceptual design report

    International Nuclear Information System (INIS)

    Dell, G.F.

    1986-01-01

    A study is made of the linear aperture for the clustered lattice used for the SSC Conceptual Design Report. Random multipole errors are included in all magnetic elements including the insertion dipoles and quadrupoles. Based on the concept of smear, the linear aperture is equal to the dynamic aperture in the range -0.1 ≤ ΔP/P ≤ 0.03%. Strong coupling for ΔP/P > 0% produces large smears. A variation of the smear parameter that is insensitive to coupling is proposed. A comparison is made with results reported in the SSC Conceptual Design Report

  5. Copolimerização em emulsão de acetato de vinila e acrilato de butila com alto teor de sólidos High solid contents semi-batch emulsion copolymerization of vinyl acetate and butyl acrylate

    Directory of Open Access Journals (Sweden)

    Mauri Palma

    2006-12-01

    Full Text Available Neste trabalho foi investigada a influência da concentração de uma mistura dos emulsificantes nonilfenol etoxilado e sulfato sódico de nonilfenol etoxilado (não iônico e iônico, respectivamente e concentração de protetor coloidal, poli (álcool vinílico na estabilidade coloidal de látices do copolímero acetato de vinila (AV/acrilato de butila (AB com alto teor de sólidos. Foram determinados o teor de sólidos e o tamanho médio das partículas ao longo da reação e foram obtidas as viscosidades das emulsões finais. Os ensaios foram realizados de acordo com um projeto fatorial com 3 níveis de concentração de emulsificantes e de protetor coloidal. Foi verificado que são necessárias maiores quantidades relativas de emulsificantes e de protetor coloidal pela massa total de monômeros para se obter látices estáveis com teores de sólidos de 70 e 73% (m/m. Os tamanhos médios das partículas no final de cada ensaio foram relativamente elevados (800 a 1000 nm e as viscosidades a 20°C relativamente baixas (500 mPa.s para teor de sólidos de 67% (m/m; para teor de sólidos de 70% (m/m as viscosidades variaram de 5.000 a 10.000 mPa.s e para teor de sólidos de 73% (m/m a viscosidade foi de 365.000 mPa.s.In this work the influence of the concentration of ionic (alkyl phenol polyglycol ether sodium sulfate, and non-ionic (alkyl phenol polyglycol ether, surfactants mixture and of protective colloid (polyvinyl alcohol on the colloidal stability of high solid contents butyl acrylate/vinyl acetate copolymers latexes was investigated. Solid contents and particle diameter were determined along the reaction and, at the end of each run, also the emulsion viscosity. The experiments were carried out according to a factorial design with three levels of surfactant and protective colloid concentrations. Higher amounts of surfactant and protective colloid per total monomers were required for the colloidal stability of emulsions with total solid

  6. Comparative Analyses of the Teaching Methods and Evaluation Practices in English Subject at Secondary School Certificate (SSC) and General Certificate of Education (GCE O-Level) in Pakistan

    Science.gov (United States)

    Behlol, Malik Ghulam; Anwar, Mohammad

    2011-01-01

    The study was conducted to compare the teaching methods and evaluation practices in English subject at secondary school certificate (SSC) and general certificate of education GCE-O-level in Pakistan. The population of the study was students, teachers and experts at SSC and 0-level in the Punjab province. Purposive and random sampling techniques…

  7. Utilisation of solid waste

    Energy Technology Data Exchange (ETDEWEB)

    Balu, K

    1978-07-01

    The prime solution to the present energy crisis is the recovery of latent energy from waste materials, for solid waste contains recoverable energy and it merely needs to be released. The paper is concerned with classification of solid waste, energy content of waste, methods of solid waste disposal, and chemical processing of solid waste. Waste disposal must be performed in situ with energy recovery. Scarcity of available land, pollution problem, and unrecovered latent energy restrict the use of the land-filling method. Pyrolysis is an effective method for the energy recovery and disposal problems. Chemical processing is suitable for the separated cellulosic fraction of the waste material.

  8. Beam-beam interaction and pacman effects in the SSC with momentum oscillation

    International Nuclear Information System (INIS)

    Mahale, N.K.; Ohnuma, S.

    1989-01-01

    In order to find the combined effects of beam-beam interaction (head-on and long-range) and random nonlinear multipoles in dipole magnets, the transverse oscillations of ''regular'' as well as ''pacman'' particles are traced for 256 synchrotron oscillation periods (corresponding to 135K revolutions) in the proposed SSC. Results obtained in this study do not show any obvious reduction of dynamic or linear apertures for pacman particles when compared with regular particles for (Δp/p) = 0. There are some indications of possible sudden or gradual increases in the oscillation amplitude, for pacman as well as regular particles, when the amplitude of momentum oscillation is as large as 3σ. 4 refs., 7 figs

  9. Alternate design concept for the SSC dipole magnet cryogenic support post

    International Nuclear Information System (INIS)

    Lipski, A.; Nicol, T.H.; Richardson, R.

    1991-03-01

    New materials and developments in the field of advanced composites have created the opportunity to take a fresh look into the design of the cryogenic supports for SSC collider dipole cryostats. Although the present reentrant post design meets the structural and thermal requirements, its assembly requires precision and proficiency. The objective of the proposed alternate concept is to reduce the overall cost of the support post by means of simplifying and optimizing its component design and assembly process. The present shrink fitted tube assembly may potentially be replaced by injection molded parts. New resin systems with lower thermal conductivity and high strength properties enable the utilization of automated production techniques such as injection molding and filament winding. This paper will provide analysis and design information for the alternate support post concept and compare its test performance and cost to the present support post. 3 refs., 12 figs., 4 tabs

  10. Transient beam loading and rf power distribution in the SSC [Superconducting Super Collider

    International Nuclear Information System (INIS)

    Raka, E.C.

    1986-01-01

    Transient beam loading will occur in the SSC at injection as the fifteen individual batches from the High Energy Booster are loaded box-car fashion into the main rings. Periodic transient beam loading will be present also at injection due to the gaps between the successive batches as well as the gap that remains to be filled. Even after the rings have been ''filled'' there will remain the abort gap of 3.1 μsec. This can produce significant modulation of the phase and amplitude of the rf voltage seen by those bunches immediately following it unless corrective measures are taken. Two different methods of reducing this modulation will be discussed, each of which put certain requirements on the rf power distribution system

  11. Overview of data filtering/acquisition for a 4π detector at the SSC

    International Nuclear Information System (INIS)

    Lankford, A.J.; Dubois, G.P.

    1986-01-01

    The task of the Data Filtering/Acquisition Working Group was to examine the feasibility of acquiring data at the Superconducting Super Collider (SSC) event rates from a 4-π detector with approximately three-quarters of a million electronic channels. An overview of the work on data filtering and acquisition is provided. The assumptions made about the detector, event rates, and event sizes are reviewed, and the overall picture of data flow through the data acqisition system is outlined. The problems of and the general approach to handling of the data during the analog and higher level trigger decision periods are described. The flow of the data to the online processor farm is sketched. Comments are made on software trigger strategies. Some aspects of the overall picture of a generic data acquisition system are sketched. Major issues and some needed develoments are summarized. 12 refs., 3 figs

  12. Conceptual design of a superconducting solenoid for a magnetic SSC [Superconducting Super Collider] detector

    International Nuclear Information System (INIS)

    Fast, R.W.; Grimson, J.H.; Kephart, R.D.; Krebs, H.J.; Stone, M.E.; Theriot, D.; Wands, R.H.

    1988-07-01

    The conceptual design of a large superconducting solenoid suitable for a magnetic detector at the Superconducting Super Collider (SSC) has begun at Fermilab. The magnet will provide a magnetic field of 2 T over a volume 8 m in diameter by 16 m long. The particle-physics calorimetry will be inside the field volume and so the coil will be bath cooled and cryostable; the vessels will be stainless steel. Predictibility of performance and the ability to safely negotiate all probable failure modes, including a quench, are important items of the design philosophy. Although the magnet is considerably larger than existing solenoids of this type and although many issues of manufacturability, transportability and cost have not been completely addressed, our conceptual design has convinced us that this magnet is a reasonable extrapolation of present technology. 2 figs., 2 tabs

  13. Design and performance of a new 50mm quadrupole magnet for the SSC

    International Nuclear Information System (INIS)

    Spigo, G.; Cunningham, G.; Goodzeit, C.; Orrell, D.; Turner, J.; Jayakumar, R.

    1994-01-01

    A superconducting quadrupole model magnet with a 50 mm aperture and a gradient of 190 T/m, in operation at 4.35 K and 6500 A, has been designed, built and tested at the SSC. This accelerator magnet is expected to have application in the interaction regions of the collider main rings. Its dipole-type stainless steel collars with mated self-aligning pole spacers were a major innovation in design. The model had stringent requirements on field quality and a conservative 21% current margin. The first two articles have now demonstrated satisfactory quench performance over several thermal cycles, reaching plateau at approximately 8660 A with minimal training. This paper is a brief sketch of the design and preliminary results on the first model. Fabrication and testing are described in other papers of this conference

  14. Design of a model dipole magnet for the SSC high energy booster

    International Nuclear Information System (INIS)

    Hassan, N.; Couzens, K.; Dwyer, S.; Jaisle, A.; Jayakumar, R.; Krishnamurthy, S.; Mihelic, R.; Phillips, S.; Puri, R.K.; Sarna, K.

    1994-01-01

    A superconducting model dipole magnet has been designed to serve as a vehicle in an R ampersand D program to develop a dipole magnet for potential use in the SSC High Energy Booster. The objective has been to use the Brookhaven National Laboratory (BNL) and Fermi National Accelerator Laboratory (FNAL) 50 mm aperture dipole designs to the maximum possible extent for design of a dipole magnet with the same size aperture and a field intensity of 6.67 T. Objectives of this program have also included an evaluation of magnet cross section designs which provides increased margin and includes a field quality iteration on BNL and FNAL dipole designs. The salient parameters of this magnet are listed. In this paper the 2D magnetic and mechanical design of the cold mass in conceptual and detailed form is presented

  15. A front-end system for industrial type controls at the SSC

    International Nuclear Information System (INIS)

    Haenni, D.R.

    1992-01-01

    The SSC control system is tasked with coordinating the operation of many different accelerator subsystems, a number of which use industrial type process controls. The design of a high-performance control system front end is presented which serves both as a data concentrator and a distributed process controller. In addition it provides strong support for a centralized control system architecture, allows for regional control systems, and simplifies the construction of inter-subsystem controls. An implementation of this design will be discussed which uses STD-Bus for accelerator hardware interfacing, a time domain multiplexing (TDM) communications transport system, and a modified reflective memory interface to the rest of the control system. (author)

  16. Q → qZ decays at Tevatron and SSC energies

    International Nuclear Information System (INIS)

    Agrawal, P.; Ellis, S.D.

    1990-09-01

    The possible existence of a new heavy quark Q that decays predominantly via the flavor changing neutral current transition Q → qZ is discussed. Candidates include a fourth generation charge -- 1/3 quark, or a more exotic vector-like quark. Such particles are interesting both as extensions of the Standard Model and due to their unique decay modes. The primary experimental indication of the pair production and subsequent decay of quarks is ZZ pair production at an essentially strong interaction rate. This mode can then constitute an unexpected background to the searches for other particles. In particular the channel Q bar Q → ZZ + X can generate a serious background to the search for the Higgs boson via the H 0 → ZZ mode at the SSC. Thus it is essential to search for such new heavy quarks at the Tevatron. Possible detection signatures for this purpose are discussed. 24 refs. , 1 fig., 3 tabs

  17. Development of superconducting wire and cable for the SSC project in Sumitomo Electric Industries

    International Nuclear Information System (INIS)

    Sashida, T.; Saito, S.; Oku, G.; Kurimoto, K.; Yamada, Y.; Yokota, M.; Ohmatsu, K.; Nagata, M.

    1991-01-01

    As a large production volume of NbTi superconducting wire and cable is required for the SSC project, a production process has been developed at Sumitomo Electric to optimize critical variables of wire properties. To achieve high electrical properties and a high overall yield of NbTi alloy in the fabrication process, the authors have employed carefully designed large size multifilament billets weighing more than 350kg to decrease the number of billets in large production scale. The collider dipole magnet consists of inner and outer cables, and the cable should be as uniform as possible to ensure the performance of the magnets. The authors studied two aspects to obtain such uniformity of superconducting wire; one is the selection of unit weight and the other is the property of critical current density of a strand

  18. Quench start localization in full-length SSC R ampersand D dipoles

    International Nuclear Information System (INIS)

    Devred, A.; Chapman, M.; Cortella, J.; Desportes, A.; Kaugerts, J.; Kirk, T.; Mirk, K.; Schermer, R.; Tompkins, J.C.; Turner, J.; Bleadon, M.; Brown, B.C.; Hanft, R.; Kuchnir, M.; Lamm, M.; Mantsch, P.; Mazur, P.O.; Orris, D.; Peoples, J.; Strait, J.; Tool, G.; Caspi, S.; Gilbert, W.; Meuser, R.; Peters, C.; Rechen, J.; Royet, J.; Scanlan, R.; Taylor, C.; Zbasnik, J.

    1989-04-01

    Full-length SSC R ampersand D dipole magnets instrumented with four voltage taps on each turn of the inner quarter coils have been tested. These voltage taps enable accurate location of the point at which the quenches start and detailed studies of quench development in the coil. Attention here is focused on localizing the quench source. After recalling the basic mechanism of a quench (why it occurs and how it propagates), the method of quench origin analysis is described: the quench propagation velocity on the turn where the quench occurs is calculated, and the quench location is then verified by reiterating the analysis on the adjacent turns. Last, the velocity value, which appears to be higher than previously measured, is discussed

  19. 1.8K conditioning (non-quench training) of a model SSC dipole

    International Nuclear Information System (INIS)

    Gilbert, W.S.; Hassenzahl, W.V.

    1986-09-01

    The accepted hypothesis is that training quenches are caused by heat generation when conductors move under Lorentz force. Afterwards no conductor motion will occur until a higher field and greater Lorentz force acts. If superior heat transfer and/or greater temperature margin is provided by operating at lower bath temperature, one might expect that the heat generated by conductor motion will not cause a runaway temperature increase, or quench. To test this hypothesis, the central dipole field in SSC model magnets was ramped at 1.8 K to 7.1 tesla without the magnets' quenching. The bath was then raised to 4.4 K and the magnets quenched at their short sample limits of 6.6 tesla or higher. Comparison with similar magnets trained in He I at 4.4 K is made and the significance of the non-quench training on system operation is discussed

  20. Two-dimensional magnetic sensitivity to asymmetric and symmetric deviations for SSC quadrupole magnets

    International Nuclear Information System (INIS)

    Xu, M.; Waynert, J.A.

    1994-01-01

    The magnetic multipole sensitivity to asymmetric and symmetric deviations is analyzed in the two-dimensional cross-section of SSC quadrupole magnets. Deviations in the 2D cross-section caused by variations in the superconducting cable locations due to changes in the thickness of the pole sheet, mid plane insulation, inter-layer spacer, backing sheet, and copper wedges have direct impact on the magnetic field gradient and multipoles in the straight section of the magnets. Asymmetric deviations due to different coil sizes in a cross-section are also analyzed. The analyses are performed mainly with the software package AHARM. SSCMAG and finite element software PE2D were also used to obtain baselines and to verify the results. The results provide information essential to an understanding of the deviations of the multipoles resulting from manufacturing processes, and suggest possibilities for tuning the multipoles to meet the magnetic requirements

  1. Dynamic aperture and performance of the SSC low energy booster lattice

    International Nuclear Information System (INIS)

    Pilat, F.; Bourianoff, G.; Cole, B.; Talman, R.; York, R.

    1991-05-01

    A systematic study of lattice designs proposed for the SSC Low Energy Booster has been performed, where the dynamic behavior of high transition gamma lattices is compared with that of a simpler FODO- like machine. After optimization of the transverse tunes, the dynamic aperture is determined by tracking the chromaticity corrected, ''ideal'' lattices, where the only sources on nonlinearity are the chromaticity sextupoles. The robustness of the lattices against misalignment, systematic and random errors is then evaluated and error compensation schemes worked out. The computational speed of the TEAPOT code has been greatly enhanced by porting and running its tracking core on the Intel iPSC/860 parallel computer. 7 refs., 5 figs., 3 tabs

  2. SSC Diversity Receiver over Correlated Fading Channels in the Presence of Cochannel Interference

    Directory of Open Access Journals (Sweden)

    Panić StefanR

    2010-01-01

    Full Text Available This paper studies the performances of a dual-branch switched-and-stay combining (SSC diversity receiver, operating over correlated fading in the presence of cochannel interference (CCI. Very useful, novel, infinite series expressions are obtained for the output signal to interference ratio's (SIR's probability density function (PDF and cumulative distribution function (CDF. The performance analysis is based on an outage probability (OP and an average bit error probability (ASEP criteria. ASEP is efficiently evaluated for modulation schemes such as noncoherent frequency-shift keying (NCFSK and binary differentially phase-shift keying (BDPSK. The effects of various parameters, such as input SIR unbalance, the level of correlation between received desired signals and interferences, nonlinearity of the environment, and fading severity on systems performances are graphically presented and analyzed.

  3. Coil measurement data acquisition and curing press control system for SSC dipole magnet coils

    International Nuclear Information System (INIS)

    Dickey, C.E.

    1989-03-01

    A coil matching program, similar in theory to the methods used to match Tevatron coils, is being developed at Fermilab. Modulus of elasticity and absolute coil size will be determined at 18-inch intervals along the coils while in the coil curing press immediately following the curing process. A data acquisition system is under construction to automatically acquire and manage the large quantities of data that result. Data files will be transferred to Fermilab's VAX Cluster for long-term storage and actual coil matching. The data acquisition system will also provide the control algorithm for the curing press hydraulic system. A description of the SSC Curing Press Data Acquisition and Controls System will be reported. 20 figs

  4. 1. 8K conditioning (non-quench training) of a model SSC dipole

    Energy Technology Data Exchange (ETDEWEB)

    Gilbert, W.S.; Hassenzahl, W.V.

    1986-09-01

    The accepted hypothesis is that training quenches are caused by heat generation when conductors move under Lorentz force. Afterwards no conductor motion will occur until a higher field and greater Lorentz force acts. If superior heat transfer and/or greater temperature margin is provided by operating at lower bath temperature, one might expect that the heat generated by conductor motion will not cause a runaway temperature increase, or quench. To test this hypothesis, the central dipole field in SSC model magnets was ramped at 1.8 K to 7.1 tesla without the magnets' quenching. The bath was then raised to 4.4 K and the magnets quenched at their short sample limits of 6.6 tesla or higher. Comparison with similar magnets trained in He I at 4.4 K is made and the significance of the non-quench training on system operation is discussed.

  5. Field quality of the end sections of SSC [Superconducting Super Collider] dipoles

    International Nuclear Information System (INIS)

    Hassenzahl, W.V.; Caspi, S.; Gilbert, W.; Helm, M.; Laslett, L.J.; Morgan, G.A.

    1986-09-01

    The central or two-dimensional field of a dipole magnet can be calculated with some precision. The fields at the end of the magnet, which are three-dimensional in nature, provide a more complicated problem. Starting with an end design that produced a relatively good end in terms of multipole components, a method of extending parts of the straight section was used to reduce the most important harmonics, the sextupole and decapole, to a negligible level. In addition, the effect of extending an iron yoke over the ends of a magnet was investigated and it was found to have little effect on the harmonics, though it will raise the dipole field. These results are encouraging as they imply that good ends can be developed with relative ease should the two dimensional cross-section of a dipole magnet such as the SSC have to be changed

  6. Development of a customized SSC pixel detector readout for vertex tracking

    International Nuclear Information System (INIS)

    Barkan, O.; Atlas, E.L.; Marking, W.L.; Worley, S.; Yacoub, G.Y.; Kramer, G.; Arens, J.F.; Jernigan, J.G.; Shapiro, S.L.; Nygren, D.; Spieler, H.; Wright, M.

    1990-01-01

    The authors describe the readout architecture and progress to date in the development of hybrid PIN diode arrays for use as vertex detectors in the SSC environment. The architecture supports a self-timed mechanism for time stamping hit pixels, storing their xy coordinates and later selectively reading out only those pixels containing interesting data along with their coordinates. The peripheral logic resolves ambiguous pixel ghost locations and controls pixel neighbor readout to achieve high spatial resolution. A test lot containing 64 x 32 pixel arrays has been processed and is currently being tested. Each pixel contains 23 transistors and six capacitors consuming an area of 50μm by 150μm and dissipating about 20μW of power

  7. Detection of a new Z' in the Z' → W+W- mode at the SSC

    International Nuclear Information System (INIS)

    Deshpande, N.G.; Gunion, J.F.; Zwirner, F.

    1987-07-01

    If a new Z' exists with mass in the TeV region, the decay rate for the mode Z' → W + W - is expected to be of the same order as the ones for Z' → e + e - or Z' → μ + μ - . This mode can be detectable at the SSC via the secondary decays WW → (jet jet)(l nu), (l = e,μ). We compare the expected signal with the backgrounds coming from continuum WW production and W jet jet production in the standard model. Using for this decay selection criteria analogous to the ones proposed for the corresponding decay of a heavy Higgs, we conclude that the signal/background ratio should be considerably larger in the Z' case. This is primarily because, for masses in the TeV range, the Z' width is very much smaller than the Higgs width

  8. H/sup /minus// injection into the low-energy booster of the SSC

    International Nuclear Information System (INIS)

    Colton, E.P.; Thiessen, H.A.

    1988-01-01

    Protons are accumulated into the low-energy booster of the SSC by utilizing H/sup /minus// → H + conversion in a 225- μg/cm 2 carbon stripping foil. Synchronous injection is performed for 26 turns into stationary rf buckets, thereby allowing operation with variable bunch spacing. By injecting the beam offset in x and y we obtain the required rms normalized transverse emittance area of 0.75 π mm-mr. Similarly the required rms longitudinal emittance area of 1.75π /times/ 10/sup /minus/3/ eVs is obtained by injecting single linac micropulses, centered at /phi/ = 0, and dp/p = +0.12%, into each 49.9-MHz rf bucket formed with an rf voltage of 350 kV. The transverse space-charge tune shift is -0.17 for 10 10 protons/bunch accumulated at 600 MeV. 1 ref., 5 figs., 1 tab

  9. Lamination and end pack design studies of SSC low energy booster magnet prototypes

    International Nuclear Information System (INIS)

    Li, N.

    1993-05-01

    The SSC Laboratory plans to deploy two ''large'' detectors for the essential high-energy physics experiments at the initial startup of the collider. The GEM detector is optimized to emphasize precise measurement of photons and electrons, as well as precise tracking of high-energy muons. An essential part of the GEM detector is the magnet subsystem, which provides the magnetic field necessary for identification and high-resolution tracking of charged particles. This large superconducting magnet system, with ferromagnetic field-shapers, presents a variety of engineering challenges in superconductor technology, in magnet-winding technology, fabrication, assembly and installation of large and heavy components, and in ensuring the required high operating availability

  10. A design approach to achieving the field uniformity requirements for the SSC dipole magnets

    International Nuclear Information System (INIS)

    Pavlik, D.; Krefta, M.P.; Johnson, D.C.

    1991-01-01

    This work describes a design approach for the calculation of the magnetic field quality in the SSC dipole magnets. A description of different analytical techniques including two and three dimensional finite element, finite difference and closed form methods is presented. Their application to the field quality problem is discussed showing how each can be relevant to a portion of the problem. Sources of field quality error and their impact on magnet operation are presented. Included are geometric variations of the conductors, yoke and collar, variabilities in material properties, persistent currents, saturation effects and the influence of boundary conditions. An approach to integrating the analytical methods and codes into a comprehensive design plan and set of manufacturing specifications is described

  11. Three dimensional δf simulations of beams in the SSC

    International Nuclear Information System (INIS)

    Koga, J.; Tajima, T.; Machida, S.

    1993-01-01

    A three dimensional δf strong-strong algorithm has been developed to apply to the study of such effects as space charge and beam-beam interaction phenomena in the Superconducting Super Collider (SSC). The algorithm is obtained from the merging of the particle tracking code Simpsons used for 3 dimensional space charge effects and a δf code. The δf method is used to follow the evolution of the non-gaussian part of the beam distribution. The advantages of this method are twofold. First, the Simpsons code utilizes a realistic accelerator model including synchrotron oscillations and energy ramping in 6 dimensional phase space with electromagnetic fields of the beams calculated using a realistic 3 dimensional field solver. Second, the beams are evolving in the fully self-consistent strong-strong sense with finite particle fluctuation noise is greatly reduced as opposed to the weak-strong models where one beam is fixed

  12. Three dimensional [delta]f simulations of beams in the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Koga, J.; Tajima, T. (Texas Univ., Austin, TX (United States). Inst. for Fusion Studies); Machida, S. (Superconducting Super Collider Lab., Dallas, TX (United States))

    1993-02-01

    A three dimensional [delta]f strong-strong algorithm has been developed to apply to the study of such effects as space charge and beam-beam interaction phenomena in the Superconducting Super Collider (SSC). The algorithm is obtained from the merging of the particle tracking code Simpsons used for 3-dimensional space charge effects and a [delta]f code. The [delta]f method is used to follow the evolution of the non-gaussian part of the beam distribution. The advantages of this method are twofold. First, the Simpsons code utilizes a realistic accelerator model including synchrotron oscillations and energy ramping in 6-dimensional phase space with electromagnetic fields of the beams calculated using a realistic 3-dimensional field solver. Second, the beams are evolving in the fully self-consistent strong-strong sense where finite particle fluctuation noise is greatly reduced as opposed to the weak-strong models where one beam is fixed.

  13. Three dimensional {delta}f simulations of beams in the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Koga, J.; Tajima, T. [Texas Univ., Austin, TX (United States). Inst. for Fusion Studies; Machida, S. [Superconducting Super Collider Lab., Dallas, TX (United States)

    1993-02-01

    A three dimensional {delta}f strong-strong algorithm has been developed to apply to the study of such effects as space charge and beam-beam interaction phenomena in the Superconducting Super Collider (SSC). The algorithm is obtained from the merging of the particle tracking code Simpsons used for 3-dimensional space charge effects and a {delta}f code. The {delta}f method is used to follow the evolution of the non-gaussian part of the beam distribution. The advantages of this method are twofold. First, the Simpsons code utilizes a realistic accelerator model including synchrotron oscillations and energy ramping in 6-dimensional phase space with electromagnetic fields of the beams calculated using a realistic 3-dimensional field solver. Second, the beams are evolving in the fully self-consistent strong-strong sense where finite particle fluctuation noise is greatly reduced as opposed to the weak-strong models where one beam is fixed.

  14. Three dimensional δf simulations of beams in the SSC

    International Nuclear Information System (INIS)

    Koga, J.; Tajima, T.

    1993-02-01

    A three dimensional δf strong-strong algorithm has been developed to apply to the study of such effects as space charge and beam-beam interaction phenomena in the Superconducting Super Collider (SSC). The algorithm is obtained from the merging of the particle tracking code Simpsons used for 3-dimensional space charge effects and a δf code. The δf method is used to follow the evolution of the non-gaussian part of the beam distribution. The advantages of this method are twofold. First, the Simpsons code utilizes a realistic accelerator model including synchrotron oscillations and energy ramping in 6-dimensional phase space with electromagnetic fields of the beams calculated using a realistic 3-dimensional field solver. Second, the beams are evolving in the fully self-consistent strong-strong sense where finite particle fluctuation noise is greatly reduced as opposed to the weak-strong models where one beam is fixed

  15. Three dimensional [delta][ital f] simulations of beams in the SSC

    Energy Technology Data Exchange (ETDEWEB)

    Koga, J.; Tajima, T. (Institute for Fusion Studies, The University of Texas at Austin, Austin, Texas 78712-1060 (United States)); Machida, S. (SSC Laboratory, 2550 Beckleymeade Avenue, Dallas, Texas 75237 (United States))

    1993-12-25

    A three dimensional [delta][ital f] strong-strong algorithm has been developed to apply to the study of such effects as space charge and beam-beam interaction phenomena in the Superconducting Super Collider (SSC). The algorithm is obtained from the merging of the particle tracking code Simpsons used for 3 dimensional space charge effects and a [delta][ital f] code. The [delta][ital f] method is used to follow the evolution of the non-gaussian part of the beam distribution. The advantages of this method are twofold. First, the Simpsons code utilizes a realistic accelerator model including synchrotron oscillations and energy ramping in 6 dimensional phase space with electromagnetic fields of the beams calculated using a realistic 3 dimensional field solver. Second, the beams are evolving in the fully self-consistent strong-strong sense with finite particle fluctuation noise is greatly reduced as opposed to the weak-strong models where one beam is fixed.

  16. Lamination and end plate design studies of SSC Low Energy Booster magnet prototypes

    International Nuclear Information System (INIS)

    Li, N.

    1993-01-01

    The LEB machine includes six kinds of laminated magnets and 4 kinds of laminations. The main quadrupole magnet and low field and high field corrector quadrupoles use the same lamination shape. The chromaticity sextupole, corrector dipole, and main dipole have different lamination designs. To test the physical design and production procedure for the magnets, it is necessary to build 2 or 3 prototypes for each kind of magnet. The ZVI plant in Moscow, manufactured all 4 kinds of lamination punching dies for the LEB magnets. Each die takes 3 to 5 months to fabricate. SSCL manufactured laser cut laminated magnet prototypes in the SSC shop at the same time. Since the LEB cycles at 10 Hz, the high frequency current and laminated end plate design causes a delamination problem on the magnet end. This problem is of concern and will be addressed

  17. What the quality philosophy brings to a research and development environment like the SSC

    International Nuclear Information System (INIS)

    Davis, S.; Wentz, J.

    1993-04-01

    In achieving major schedule and performance milestones with a project as technologically advanced as the Superconducting Super Collider, many activities must be coordinated simultaneously without the luxury of a conventional design review process. Because the design may change several times prior to the delivery of a one-of-a-kind or prototype component or subsystem, close verification and monitoring of design, manufacturing and test processes are needed on a real-time basis. This verification and monitoring is performed on two levels by Quality Assurance at the SSC Laboratory; Division and General Management. The Division level is involved in day-today activities at the Laboratory and the Suppliers; the General Management level performs the independent oversight function for all the Laboratory quality processes. In the divisions, continuous monitoring of design, procurement, manufacturing, installation, and testing activities is performed. At the General Management level, quality program development and implementation is evaluated within each division. Critical suppliers involved in system design, manufacturing, and testing are evaluated against contract and program requirements to assure systems safely perform their intended functions. Responsibilities for quality are extended by the participation of the SSCL Quality Assurance Office in Accelerator Readiness Reviews (ARR) previously known as Operational Readiness Reviews (ORR) for each major machine developed and designed at the Laboratory. Quality Assurance promoted continuous awareness of DOE contract requirements, SSC Laboratory Quality Assurance requirements and the Safety Analysis Report requirements which is not an easy task in the scientific community. A result has been a new cooperative attitude in which physicists, scientists, engineers, safety and quality professionals can work together towards a common goal

  18. An assessment of the SSC impact on the training and employment needs of North Central Texas

    International Nuclear Information System (INIS)

    Orsak, C.G.; McGlohen, P.; Jenkens, L.

    1992-01-01

    The Texas Higher Education Coordinating Board has funded the Navarro College/Dallas County Community College Districe SSC Technical Training Project to determine the direct and inderect manpower needs in the eighteen-county North Cenbtral Texas area surrounding the Superconducting Super Collider Laboratory (SSCL) and to identify training programs to be developed by local community colleges. The tasks of this project were specifically designed to maximize the use of existing informatiion resources of various organizations and agencies concerned with lobor force development issues to provide custom databases focusied upon the SSCL. The labor market informataion (LMI) resources developed in this project provide a strong foundation for examining the impacts of the SSCL on the training and employment needs of the North Central Texas region. The direct and indirect effects of the SSCL are analyzed to the smallest level of occupational detail feasible. Regional labor demand estimates and forecasts were updated and expanded, county level demand data was developed, statewide vocational education programs were inventoried and lists of affected regional employers were extracted. All of the data developed in this project is available in standard Dbase disk files, formatted to be compatible with other LMI resources such as INTERLINK's LMIS. Further, a custom version of INTERLINK's PC-based LMIS software was developed for the SSC Technical Training Project to provide the greatest access to and linkage between the labor demand and supply data developed in this study. Future efforts to develop additional information resources relevant to the event of the SSCL must focus upon comparative analyses of similar projects, such as Fermilab and others, to provide more detail to the products developed in this project

  19. Cryogenic systems for the SSC and the status of their development

    International Nuclear Information System (INIS)

    Fietz, W.A.; Ganni, V.; Abramovich, S.; Niehaus, T.

    1993-07-01

    The Superconducting Super Collider (SSC) consists of two parallel magnet rings, each 87,120 m in circumference, constructed in a tunnel 25 to 74 m underground. Protons are injected into these ring from the high energy booster (HEB), which contains a separate magnet ring 10,800 m in circumference constructed in a tunnel 14 m above the collider tunnel. The magnets will be operated at a controlled low temperature in order to maintain the windings in the superconducting state. Therefore the magnet cryostat is designed with a high vacuum insulating chamber, multilayer insulation (MLI), and thermal shields at 84 K and 20 K nominal temperatures. The major portion of the heat load is from thermal radiation and conduction through the supports, and is intercepted and absorbed by the shields. The cryogenic system for the machine is divided into sectors of nominally equal length: ten for the collider and two for the HEB. Each sector has a dedicated cryogenic system (SCS) as well as some level of redundancy from the neighboring SCS. The helium refrigeration plants will be installed at the midpoint of each sector. Each cryogenic sector in the collider is divided into four strings, two upper and two lower, about 4000 m long. Each string is subdivided into sections of about 1080 m, the smallest modules that can be isolated for maintenance, or for warmup and cooldown. Each section is subdivided into cells and half cells. The half cell, containing six main magnets and a spool piece is 90 m long. The SSC cryogenic system for each sector consists of a sector refrigerator surface system (SRS) and a sector refrigerator tunnel system (SRT). Proposals for the SRS systems' are presently in review for vendor selection. In this paper the SRT subsystems requirements and their status will be reviewed

  20. US/Russia government-to-government cooperation in material protection, control and accounting at the SSC-RIAR, Dimitrovgrad

    International Nuclear Information System (INIS)

    Kharlanov, Y.I.; Gadzhiev, G.I.; Satkowiak, L.

    1996-01-01

    The US/Russia Government-to-Government Cooperation in Material Protection, Control, and Accounting (MPC and A) was established in an agreement between the Department of Defense of the US and the Ministry of the russian Federation for Atomic Energy (MINATOM). A subsequent agreement between the Department of Energy (DOE) and MINATOM, resulted in the selection of the State Scientific Center-Research Institute of Atomic Reactors (SSC-RIAR) in Dimitrovgrad as one of the Russian enterprises that would participate with US national laboratories in expanded cooperation aimed at enhancing MPC and A systems in both countries. The SSC-RIAR facilities under consideration for MPC and A enhancements consist of a reactor building, a fuel fabrication building, and a storage building. The long term goal of this project is the completion of a comprehensive implementation plan, and its subsequent execution, addressing key MPC and A elements for all, or as many as possible, facilities at SSC-RIAR containing appreciable amounts of highly enriched uranium and plutonium. This paper describes the nature and scope of the expanded cooperation involving SSC-RIAR and six US national laboratories