Distilling solid carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Nielsen, H; Laing, B

1926-12-04

In a process of distilling solid carbonaceous materials with by-product recovery, the time factor and the temperature gradient during the distillation period are so controlled that a temperature difference exceeding 150/sup 0/C is avoided between the temperatures at the center and periphery of any suitable size of material or thickness of fuel bed. The material is heated by direct contact with an inert gas, such as water gas, producer gas, or combustion gases, which is passed in counterflow to the material and whose volume is such as to lower the vapor tension or partial pressure of the volatilizable oils and to withdraw the oils without cracking of the oil vapors. The material may be subjected to a preliminary heat treatment by gases containing 2 to 3 percent of free oxygen to reduce its coking properties, and free oxygen may be added either to the heating gases during the heat treatment, or to the retort and heating gases and vapors to polymerize resinous bodies prior to condensation or during condensation and while the oils are still wholly or partially in the vapor state.

Organic free radicals and micropores in solid graphitic carbonaceous matter at the Oklo natural fission reactors, Gabon

International Nuclear Information System (INIS)

Rigali, M.J.; Nagy, B.

1997-01-01

The presence, concentration, and distribution of organic free radicals as well as their association with specific surface areas and microporosities help characterize the evolution and behavior of the Oklo carbonaceous matter. Such information is necessary in order to evaluate uranium mineralization, liquid bitumen solidification, and radio nuclide containment at Oklo. In the Oklo ore deposits and natural fission reactors carbonaceous matter is often referred to as solid graphitic bitumen. The carbonaceous parts of the natural reactors may contain as much as 65.9% organic C by weight in heterogeneous distribution within the clay-rich matrix. The solid carbonaceous matter immobilized small uraninite crystals and some fission products enclosed in this uraninite and thereby facilitated radio nuclide containment in the reactors. Hence, the Oklo natural fission reactors are currently the subjects of detailed studies because they may be useful analogues to support performance assessment of radio nuclide containment at anthropogenic radioactive waste repository sites. Seven carbonaceous matter rich samples from the 1968 ± 50 Ma old natural fission reactors and the associated Oklo uranium ore deposit were studied by electron spin resonance (ESR) spectroscopy and by measurements of specific surface areas (BET method). Humic acid, fulvic acid, and fully crystalline graphite standards were also examined by ESR spectroscopy for comparison with the Oklo solid graphitic bitumens. With one exception, the ancient Oklo bitumens have higher organic free radical concentrations than the modem humic and fulvic acid samples. The presence of carbon free radicals in the graphite standard could not be determined due to the conductivity of this material. 72 refs., 7 figs., 1 tab

Black liquor-derived carbonaceous solid acid catalyst for the hydrolysis of pretreated rice straw in ionic liquid.

Science.gov (United States)

Bai, Chenxi; Zhu, Linfeng; Shen, Feng; Qi, Xinhua

2016-11-01

Lignin-containing black liquor from pretreatment of rice straw by KOH aqueous solution was applied to prepare a carbonaceous solid acid catalyst, in which KOH played dual roles of extracting lignin from rice straw and developing porosity of the carbon material as an activation agent. The synthesized black liquor-derived carbon material was applied in catalytic hydrolysis of the residue solid from the pretreatment of rice straw, which was mainly composed of cellulose and hemicellulose, and showed excellent activity for the production of total reducing sugars (TRS) in ionic liquid, 1-butyl-3-methyl imidazolium chloride. The highest TRS yield of 63.4% was achieved at 140°C for 120min, which was much higher than that obtained from crude rice straw under the same reaction conditions (36.6% TRS yield). Overall, this study provides a renewable strategy for the utilization of all components of lignocellulosic biomass. Copyright © 2016 Elsevier Ltd. All rights reserved.

Handling of Solid Residues

International Nuclear Information System (INIS)

Medina Bermudez, Clara Ines

1999-01-01

The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

Biomass-derived carbonaceous materials as components in wood briquettes

Energy Technology Data Exchange (ETDEWEB)

Stengl, S.; Koch, C.; Stadlbauer, E.A.; Scheer, J. [Univ. of Applied Sciences, THM Campus Giessen, Giessen (Germany); Weber, B. [Instituto de Ingenieria de la Universidad Nacional Autonoma de Mexico (UNAM), Coyoacan (Mexico); Strohal, U.; Fey, J. [Strohal Anlagenbau, Staufenberg (Germany)

2012-11-01

The present paper describes a briquette composed of a substantial amount of wooden biomass and up to 35% of carbonaceous materials derived from biogenic residues. The cellulosic component may be a mixture of any wooden residue. Suitable substrates for the carbonaceous fraction are vegetation wastes from land management or agriculture. Depending on physical and chemical nature of the substrate, Hydrothermal Carbonisation (HTC) or Low Temperature Conversion (LTC) may be used to produce the carbonaceous part of the briquette. HTC turns wet biomass at temperatures around 200 deg C in an autoclave into lignite whereas LTC treatment at 400 deg C and atmospheric pressure produces black coal. This is manifested by a molar ratio of 0.1 {<=} H/C (LTC) {<=} 0.7; 0.05{<=} O/C (LTC) {<=} 0.4 and 0.7 < H/C (HTC) <1.5 ; 0.2< O/C (HTC) < 0.5. Solid state {sup 13}C-NMR confirms these findings showing a strong absorption band for sp{sup 2}-hybridized carbon atoms at chemical shifts of 100 ppm und 165 ppm for LTC biochar. Depending on the substrate, HTC gives rise to an increase in the specific calorific value (MJ/kg) by a factor of {Psi} {approx} 1.2 - 1.4; LTC by 1.5 - 1.8. In addition ash melting points are significantly increased; in case of wheat straw by about 200 deg C. Compacted products may have a cylindrical or rectangular profile.

Solid residues

International Nuclear Information System (INIS)

Mulder, E.; Duin, P.J. van; Grootenboer, G.J.

1995-01-01

A summary is presented of the many investigations that have been done on solid residues of atmospheric fluid bed combustion (AFBC). These residues are bed ash, cyclone ash and bag filter ash. Physical and chemical properties are discussed and then the various uses of residues (in fillers, bricks, gravel, and for recovery of aluminium) are summarised. Toxicological properties of fly ash and stack ash are discussed as are risks of pneumoconiosis for workers handling fly ash, and contamination of water by ashes. On the basis of present information it is concluded that risks to public health from exposure to emissions of coal fly ash from AFBC appear small or negligible as are health risk to workers in the coal fly ash processing industry. 35 refs., 5 figs., 12 tabs

Machine for compacting solid residues

International Nuclear Information System (INIS)

Herzog, J.

1981-11-01

Machine for compacting solid residues, particularly bulky radioactive residues, constituted of a horizontally actuated punch and a fixed compression anvil, in which the residues are first compacted horizontally and then vertically. Its salient characteristic is that the punch and the compression anvil have embossments on the compression side and interpenetrating plates in the compression position [fr

Successive self-propagating sintering process using carbonaceous materials: A novel low-cost remediation approach for dioxin-contaminated solids

Energy Technology Data Exchange (ETDEWEB)

Zhao, Long, E-mail: zhaolong@craes.org.cn [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Dayangfang 8, Beijing 100012 (China); Hou, Hong, E-mail: houhong@craes.org.cn [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Dayangfang 8, Beijing 100012 (China); Zhu, Tengfei; Li, Fasheng [State Key Laboratory of Environmental Criteria and Risk Assessment, Chinese Research Academy of Environmental Sciences, Dayangfang 8, Beijing 100012 (China); Terada, Akihiko; Hosomi, Masaaki [Department of Chemical Engineering, Faculty of Engineering, Tokyo University of Agriculture and Technology, 2-24-16 Naka-cho, Koganei, Tokyo 184-8588 (Japan)

2015-12-15

Highlights: • A SSPSP using carbonaceous materials for removing dioxin pollutants was developed. • Removal and degradation efficiencies of DL-PCBs were higher than those of PCDD/Fs. • Compositions of PCDD/Fs were dependent on the available precursors in raw materials. • Dechlorination of O{sub 8}CDD and formation pathways of PCDFs were deduced. • Dioxin levels in the effluent gas complied with the International emission limit. - Abstract: The disposal of dioxin-contaminated solids was studied using a novel successive self-propagating sintering process (SSPSP) incorporating a carbonaceous material. Among the five types of carbonaceous materials investigated, Charcoal B displayed optimum adsorbent properties and was selected as the best thermal source in the current remediation approach based on economical efficiency aspects. The feasibility of this proposed approach, removal efficiencies, and congener compositions of dioxins were examined using two types of dioxin-contaminated solids (Fugan sediment and Toyo soil) that displayed different characteristics including the initial concentrations of dioxins. The removal efficiencies of DL-PCBs (“dioxin-like” polychlorinated biphenyls) were higher than those of PCDD/Fs (polychlorinated dibenzo-p-dioxins/dibenzofurans), achieving 99.9 and 92% removal in the Fugan sediment and Toyo soil, respectively. In contrast, the degradation efficiencies of DL-PCBs were lower (i.e., 89.3 and 88.8%, respectively). The initial concentrations of dioxins, available precursors, and properties of the solids strongly influenced the congener compositions and removal efficiencies of dioxins. Furthermore, the dechlorination reaction pathways of high-chlorinated PCDDs and potential regeneration pathways of PCDFs from PCBs were deduced using isotope labeling. The proposed novel low-cost remediation approach for the removal of dioxins from solids is a highly efficient and environmentally sound treatment technology.

Successive self-propagating sintering process using carbonaceous materials: A novel low-cost remediation approach for dioxin-contaminated solids

International Nuclear Information System (INIS)

Zhao, Long; Hou, Hong; Zhu, Tengfei; Li, Fasheng; Terada, Akihiko; Hosomi, Masaaki

2015-01-01

Highlights: • A SSPSP using carbonaceous materials for removing dioxin pollutants was developed. • Removal and degradation efficiencies of DL-PCBs were higher than those of PCDD/Fs. • Compositions of PCDD/Fs were dependent on the available precursors in raw materials. • Dechlorination of O_8CDD and formation pathways of PCDFs were deduced. • Dioxin levels in the effluent gas complied with the International emission limit. - Abstract: The disposal of dioxin-contaminated solids was studied using a novel successive self-propagating sintering process (SSPSP) incorporating a carbonaceous material. Among the five types of carbonaceous materials investigated, Charcoal B displayed optimum adsorbent properties and was selected as the best thermal source in the current remediation approach based on economical efficiency aspects. The feasibility of this proposed approach, removal efficiencies, and congener compositions of dioxins were examined using two types of dioxin-contaminated solids (Fugan sediment and Toyo soil) that displayed different characteristics including the initial concentrations of dioxins. The removal efficiencies of DL-PCBs (“dioxin-like” polychlorinated biphenyls) were higher than those of PCDD/Fs (polychlorinated dibenzo-p-dioxins/dibenzofurans), achieving 99.9 and 92% removal in the Fugan sediment and Toyo soil, respectively. In contrast, the degradation efficiencies of DL-PCBs were lower (i.e., 89.3 and 88.8%, respectively). The initial concentrations of dioxins, available precursors, and properties of the solids strongly influenced the congener compositions and removal efficiencies of dioxins. Furthermore, the dechlorination reaction pathways of high-chlorinated PCDDs and potential regeneration pathways of PCDFs from PCBs were deduced using isotope labeling. The proposed novel low-cost remediation approach for the removal of dioxins from solids is a highly efficient and environmentally sound treatment technology.

Management of industrial solid residues; Gerenciamento de residuos solidos industriais

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

This chapter gives an overview on the management of industrial solid wastes, approaching the following subjects: classification of industrial solid residues; directives and methodologies for the management of industrial solid residues; instruments for the management of industrial solid residues; handling, packing, storage and transportation; treatment of industrial solid residues; final disposal - landfill for industrial residues; the problem of treatment and final disposer of domestic garbage in Brazil; recycling of the lubricant oils used in brazil; legislation.

Global climate impacts of country-level primary carbonaceous aerosol from solid-fuel cookstove emissions

International Nuclear Information System (INIS)

Lacey, Forrest; Henze, Daven

2015-01-01

Cookstove use is globally one of the largest unregulated anthropogenic sources of primary carbonaceous aerosol. While reducing cookstove emissions through national-scale mitigation efforts has clear benefits for improving indoor and ambient air quality, and significant climate benefits from reduced green-house gas emissions, climate impacts associated with reductions to co-emitted black (BC) and organic carbonaceous aerosol are not well characterized. Here we attribute direct, indirect, semi-direct, and snow/ice albedo radiative forcing (RF) and associated global surface temperature changes to national-scale carbonaceous aerosol cookstove emissions. These results are made possible through the use of adjoint sensitivity modeling to relate direct RF and BC deposition to emissions. Semi- and indirect effects are included via global scaling factors, and bounds on these estimates are drawn from current literature ranges for aerosol RF along with a range of solid fuel emissions characterizations. Absolute regional temperature potentials are used to estimate global surface temperature changes. Bounds are placed on these estimates, drawing from current literature ranges for aerosol RF along with a range of solid fuel emissions characterizations. We estimate a range of 0.16 K warming to 0.28 K cooling with a central estimate of 0.06 K cooling from the removal of cookstove aerosol emissions. At the national emissions scale, countries’ impacts on global climate range from net warming (e.g., Mexico and Brazil) to net cooling, although the range of estimated impacts for all countries span zero given uncertainties in RF estimates and fuel characterization. We identify similarities and differences in the sets of countries with the highest emissions and largest cookstove temperature impacts (China, India, Nigeria, Pakistan, Bangladesh and Nepal), those with the largest temperature impact per carbon emitted (Kazakhstan, Estonia, and Mongolia), and those that would provide the

Global climate impacts of country-level primary carbonaceous aerosol from solid-fuel cookstove emissions

Science.gov (United States)

Lacey, Forrest; Henze, Daven

2015-11-01

Cookstove use is globally one of the largest unregulated anthropogenic sources of primary carbonaceous aerosol. While reducing cookstove emissions through national-scale mitigation efforts has clear benefits for improving indoor and ambient air quality, and significant climate benefits from reduced green-house gas emissions, climate impacts associated with reductions to co-emitted black (BC) and organic carbonaceous aerosol are not well characterized. Here we attribute direct, indirect, semi-direct, and snow/ice albedo radiative forcing (RF) and associated global surface temperature changes to national-scale carbonaceous aerosol cookstove emissions. These results are made possible through the use of adjoint sensitivity modeling to relate direct RF and BC deposition to emissions. Semi- and indirect effects are included via global scaling factors, and bounds on these estimates are drawn from current literature ranges for aerosol RF along with a range of solid fuel emissions characterizations. Absolute regional temperature potentials are used to estimate global surface temperature changes. Bounds are placed on these estimates, drawing from current literature ranges for aerosol RF along with a range of solid fuel emissions characterizations. We estimate a range of 0.16 K warming to 0.28 K cooling with a central estimate of 0.06 K cooling from the removal of cookstove aerosol emissions. At the national emissions scale, countries’ impacts on global climate range from net warming (e.g., Mexico and Brazil) to net cooling, although the range of estimated impacts for all countries span zero given uncertainties in RF estimates and fuel characterization. We identify similarities and differences in the sets of countries with the highest emissions and largest cookstove temperature impacts (China, India, Nigeria, Pakistan, Bangladesh and Nepal), those with the largest temperature impact per carbon emitted (Kazakhstan, Estonia, and Mongolia), and those that would provide the

Catalytic production of Jatropha biodiesel and hydrogen with magnetic carbonaceous acid and base synthesized from Jatropha hulls

International Nuclear Information System (INIS)

Zhang, Fan; Tian, Xiao-Fei; Fang, Zhen; Shah, Mazloom; Wang, Yi-Tong; Jiang, Wen; Yao, Min

2017-01-01

Graphical abstract: Jatropha seeds were extracted oil for biodiesel production and the hulls were carbonized to load active sites as magnetic carbonaceous solid acid and base catalysts. Crude Jatropha oil was esterified to decrease its acid value to 1.3 from 17.2 mg KOH/g by the solid acid, and subsequently transesterified to biodiesel (96.7% yield) catalyzed by the solid base. After 3 cycles and magnetically separated, the deactivated base was catalyzed the hydrothermal gasification of biodiesel by-product (crude glycerol) with gasification rate of 81% and 82% H_2 purity. - Highlights: • High acid value (AV) crude oil was extracted from Jatropha seeds with waste hulls produced. • Carbonizing the hulls and loading active sites produced magnetic carbonaceous acid and base. • The acid reduced AV of crude oil to 1.3 from 17.2 mg KOH/g and separated for 3 cycles. • The base achieved 97.5% biodiesel yield and magnetically separated for recycles. • After 3 cycles, the deactivated base catalyzed the hydrothermal gasification of glycerol. - Abstract: Magnetic carbonaceous solid acid (C-SO_3H@Fe/JHC) and base (Na_2SiO_3@Ni/JRC) catalysts were synthesized by loading active groups on the carbonaceous supporters derived from Jatropha-hull hydrolysate and hydrolysis residue. Characterization of their morphology, magnetic saturation, functional groups and total acid/base contents were performed by various techniques. Additional acidic functional groups that formed with Jatropha-hull hydrolysate contributed to the high acidity of C-SO_3H@Fe/JHC catalyst for the pretreatment (esterification) of crude Jatropha oil with high acid values (AV). The AV of esterified Jatropha oil dropped down from 17.2 to 1.3 mg KOH/g, achieving a high biodiesel yield of 96.7% after subsequent transesterification reaction with Na_2SiO_3@Ni/JRC base that was cycled at least 3 times with little loss of catalysis activity. Both solid acid and base catalysts were easily recovered by magnetic force

Pyrolysis oil from carbonaceous solid wastes in Malaysia

International Nuclear Information System (INIS)

Islam, M.N.; Jamil, M.K.; Ani, F.N.; Zailani, R.

2000-01-01

The agro-industrial sector of Malaysia produces a huge amount of oil palm and paddy rice. These generate a significant amount of renewable biomass solid wastes in the forms of oil palm shell and rice husk. Apart from this a huge quantity of scrap tyre is generated from the country's faster increasing usage of transportation vehicles like motorcycle, car, bus and lorries. These wastes are producing pollution and disposal problems affecting the environment. Besides energy is not recovered efficiently from these waste resources. From the elemental composition and thermogravimetric analysis (TGA) studies of the wastes, it appeared that the wastes could be used for pyrolysis liquid oil production. Pyrolysis at present is deemed to be a potential method for the conversion of carbonaceous solid wastes into upgraded liquid products which can either be tried for liquid fuel or value-added chemical. A fluidized bed bench scale fast pyrolysis system was employed for this thermochemical conversion process of solid wastes. Silica sand was used as fluidized bed material and nitrogen gas as the fluidising medium. The products obtained were liquid oil, solid char and gas. The liquid oil and solid char were collected separately while the gas was flared. The maximum liquid product yield was found to vary with feedstock material fluidized bed temperature. The maximum liquid product yield was found to be 58, 53 and 40 wt. % of biomass fed at fluidized bed temperature at 500, 525 and 450 0 C respectively for oil palm shell, scrap tyre and rice husk. The solid char yield was 25, 36 and 53 wt. % of biomass fed at the condition of maximum liquid product yield for oil palm shell, scrap tyre and rice husk respectively. The oil products were subjected to FTIR, GC and GC/MS analysis for their group composition and detailed chemical compositions. The pyrolysis oil from scrap tyre was found to contain highest percentage of pure hydrocarbons (25 wt. % of total feed) with esters and oxygenated

Treating carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Pier, M

1929-08-26

To separate the constituents or conversion products, which are liquid or which liquefy when heated, from solid distillable carbonaceous materials such as coals, oil shales, or other bituminous substances, the initial materials are subjected to a destructive hydrogenation under mild conditions so that the formation of benzines is substantially avoided, after which the material is subjected to an extraction treatment with solvents. The constituents of high boiling point range, suitable for the production of lubricating oils and solid paraffins, obtained by the said destructive hydrogenation are separated off before or/and after the said extraction treatment.

Chemical analysis of solid residue from liquid and solid fuel combustion: Method development and validation

Energy Technology Data Exchange (ETDEWEB)

Trkmic, M. [University of Zagreb, Faculty of Mechanical Engineering and Naval Architecturek Zagreb (Croatia); Curkovic, L. [University of Zagreb, Faculty of Chemical Engineering and Technology, Zagreb (Croatia); Asperger, D. [HEP-Proizvodnja, Thermal Power Plant Department, Zagreb (Croatia)

2012-06-15

This paper deals with the development and validation of methods for identifying the composition of solid residue after liquid and solid fuel combustion in thermal power plant furnaces. The methods were developed for energy dispersive X-ray fluorescence (EDXRF) spectrometer analysis. Due to the fuels used, the different composition and the location of creation of solid residue, it was necessary to develop two methods. The first method is used for identifying solid residue composition after fuel oil combustion (Method 1), while the second method is used for identifying solid residue composition after the combustion of solid fuels, i. e. coal (Method 2). Method calibration was performed on sets of 12 (Method 1) and 6 (Method 2) certified reference materials (CRM). CRMs and analysis test samples were prepared in pellet form using hydraulic press. For the purpose of method validation the linearity, accuracy, precision and specificity were determined, and the measurement uncertainty of methods for each analyte separately was assessed. The methods were applied in the analysis of real furnace residue samples. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Indigenous microbial capability in solid manure residues to start-up solid-phase anaerobic digesters.

Science.gov (United States)

Yap, S D; Astals, S; Jensen, P D; Batstone, D J; Tait, S

2017-06-01

Batch solid-phase anaerobic digestion is a technology for sustainable on-farm treatment of solid residues, but is an emerging technology that is yet to be optimised with respect to start-up and inoculation. In the present study, spent bedding from two piggeries (site A and B) were batch digested at total solids (TS) concentration of 5, 10 and 20% at mesophilic (37°C) and thermophilic (55°C) temperatures, without adding an external inoculum. The results showed that the indigenous microbial community present in spent bedding was able to recover the full methane potential of the bedding (140±5 and 227±6L CH 4 kgVS fed -1 for site A and B, respectively), but longer treatment times were required than for digestion with an added external inoculum. Nonetheless, at high solid loadings (i.e. TS level>10%), the digestion performance was affected by chemical inhibition due to ammonia and/or humic acid. Thermophilic temperatures did not influence digestion performance but did increase start-up failure risk. Further, inoculation of residues from the batch digestion to subsequent batch enhanced start-up and achieved full methane potential recovery of the bedding. Inoculation with liquid residue (leachate) was preferred over a solid residue, to preserve treatment capacity for fresh substrate. Overall, the study highlighted that indigenous microbial community in the solid manure residue was capable of recovering full methane potential and that solid-phase digestion was ultimately limited by chemical inhibition rather than lack of suitable microbial community. Copyright © 2017 Elsevier Ltd. All rights reserved.

Distillation of solid carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Burney, C D

1918-08-31

A method of distilling carbonaceous material at low or moderate temperatures is described in which the main supply of gases for heating the material under treatment is generated in a combustion chamber located externally of the retort chamber from which combustion chamber the gases are withdrawn and passed under control through hollow elements located within the retort chamber in such manner as to insure the production of the desired temperature gradient along the length of the retort, the said elements being so constructed that they serve to bring the heating gases into indirect contact with the material undergoing treatment while also moving the material progressively through the retort in the opposite direction to that in which the heating gases flow.

Distilling carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Griffiths, C A

1924-04-15

In apparatus of the kind set forth for distilling solid carbonaceous materials, a rotary retort in the form of a tubular, hollow cylindrical, or other similar hollow body, of small diameter, having a thin wall is provided to which the heat is applied externally, with means operative within it adapted, not only for cleaning the internal wall of the retort but also for distributing the heat throughout the mass of materials under treatment, substantially as described.

Mineral CO2 sequestration in alkaline solid residues

International Nuclear Information System (INIS)

Huijgen, W.J.J.; Comans, R.N.J.; Witkamp, G.J.

2004-12-01

Mineral carbonation is a promising sequestration route for the permanent and safe storage of carbon dioxide. In addition to calcium- or magnesium-containing primary minerals, suitable alkaline solid residues can be used as feedstock. The use of alkaline residues has several advantages, such as their availability close to CO2 sources and their higher reactivity for carbonation than primary minerals. In addition, the environmental quality of residues can potentially be improved by carbonation. In this study, key factors of the mineral CO2 sequestration process are identified, their influence on the carbonation process is examined, and environmental properties of the reaction products with regard to their possible beneficial utilization are investigated. The use of alkaline solid residues forms a potentially attractive alternative for the first mineral sequestration plants

Electrodialytic remediation of municipal solid waste incineration residues using different membranes

DEFF Research Database (Denmark)

Parés Viader, Raimon; Jensen, Pernille Erland; Ottosen, Lisbeth M.

2017-01-01

In the present work, three different commercial membrane brands were used in an identical electrodialytic cell setup and operating conditions, in order to reduce the leaching of metals and salt anions of two types of municipal solid waste incineration residues: air pollution control residues...... as a technology to upgrade municipal solid waste incineration residues....

Renewable energy from agro-residues in China. Solid biofuels and biomass briquetting technology

Energy Technology Data Exchange (ETDEWEB)

Chen, Longjian; Han, Lujia [Center for Biomass Resource Utilization, College of Engineering, China Agricultural University (East Campus), 17 Qing-Hua-Dong-Lu, Hai-Dian District, Beijing 100083 (China); Xing, Li [Service Center for Trading Technology Service, Chinese Academy of Agricultural Mechanization Sciences, Beijing 100083 (China)

2009-12-15

China has the abundant agro-residue resources, producing more than 630 million tons of agro-residues in 2006, and amounting to about 20% of total energy consumption in rural areas. Efficient utilization of enormous agro-residues resource is crucial for providing bioenergy, releasing risk of environmental pollution, and increasing farmers' income. The paper presented the feasibility of densified solid biofuels technology for utilizing agro-residues in China. The output and distribution of agro-residues in recent 10 years, the R and D of briquetting technology, and the market of densified solid biofuels from agro-residues in China have been analyzed. The result indicated that the abundant agro-residue resources can provide the economical and sustainable raw material for densified solid biofuels development in China. The R and D of briquetting technology at present can strongly support the large scale production of densified solid biofuels. With continued improvement and cost reduction of briquetting technology, along with the support of nation energy policy on biomass energy, the market of densified solid biofuels from agro-residues in China will be more fully deployed. Based on the above mentioned key factors, development of densified solid biofuels from agro-residues in China will be promising and feasible. (author)

Renewable energy from agro-residues in China. Solid biofuels and biomass briquetting technology

International Nuclear Information System (INIS)

Chen, Longjian; Han, Lujia; Xing, Li

2009-01-01

China has the abundant agro-residue resources, producing more than 630 million tons of agro-residues in 2006, and amounting to about 20% of total energy consumption in rural areas. Efficient utilization of enormous agro-residues resource is crucial for providing bioenergy, releasing risk of environmental pollution, and increasing farmers' income. The paper presented the feasibility of densified solid biofuels technology for utilizing agro-residues in China. The output and distribution of agro-residues in recent 10 years, the R and D of briquetting technology, and the market of densified solid biofuels from agro-residues in China have been analyzed. The result indicated that the abundant agro-residue resources can provide the economical and sustainable raw material for densified solid biofuels development in China. The R and D of briquetting technology at present can strongly support the large scale production of densified solid biofuels. With continued improvement and cost reduction of briquetting technology, along with the support of nation energy policy on biomass energy, the market of densified solid biofuels from agro-residues in China will be more fully deployed. Based on the above mentioned key factors, development of densified solid biofuels from agro-residues in China will be promising and feasible. (author)

Anaerobic treatment of solid and liquid residues. Papers

International Nuclear Information System (INIS)

Maerkl, H.; Stegmann, R.

1994-01-01

Anaerobic processes are getting increasing attention in the disposal of liquid waste of the food industry and chemical industry and solid organic residues of the municipal sector. The main advantages of anaerobic processes are the favourable energy balance and the comparatively small volume of new biomass produced. There are new satisfactory technical solutions for nearly all problems encountered in practice. A conference on ''Anaerobic treatment of solid and liquid residues'' was held on 2-4 November 1994. The state of the art and new developments were presented in lectures by experts from research and practice. (orig.) [de

Estimating Residual Solids Volume In Underground Storage Tanks

International Nuclear Information System (INIS)

Clark, Jason L.; Worthy, S. Jason; Martin, Bruce A.; Tihey, John R.

2014-01-01

The Savannah River Site liquid waste system consists of multiple facilities to safely receive and store legacy radioactive waste, treat, and permanently dispose waste. The large underground storage tanks and associated equipment, known as the 'tank farms', include a complex interconnected transfer system which includes underground transfer pipelines and ancillary equipment to direct the flow of waste. The waste in the tanks is present in three forms: supernatant, sludge, and salt. The supernatant is a multi-component aqueous mixture, while sludge is a gel-like substance which consists of insoluble solids and entrapped supernatant. The waste from these tanks is retrieved and treated as sludge or salt. The high level (radioactive) fraction of the waste is vitrified into a glass waste form, while the low-level waste is immobilized in a cementitious grout waste form called saltstone. Once the waste is retrieved and processed, the tanks are closed via removing the bulk of the waste, chemical cleaning, heel removal, stabilizing remaining residuals with tailored grout formulations and severing/sealing external penetrations. The comprehensive liquid waste disposition system, currently managed by Savannah River Remediation, consists of 1) safe storage and retrieval of the waste as it is prepared for permanent disposition; (2) definition of the waste processing techniques utilized to separate the high-level waste fraction/low-level waste fraction; (3) disposition of LLW in saltstone; (4) disposition of the HLW in glass; and (5) closure state of the facilities, including tanks. This paper focuses on determining the effectiveness of waste removal campaigns through monitoring the volume of residual solids in the waste tanks. Volume estimates of the residual solids are performed by creating a map of the residual solids on the waste tank bottom using video and still digital images. The map is then used to calculate the volume of solids remaining in the waste tank. The ability to

Direct Carbon Fuel Cell System Utilizing Solid Carbonaceous Fuels

Energy Technology Data Exchange (ETDEWEB)

Turgut Gur

2010-04-30

This 1-year project has achieved most of its objective and successfully demonstrated the viability of the fluidized bed direct carbon fuel cell (FB-DCFC) approach under development by Direct Carbon technologies, LLC, that utilizes solid carbonaceous fuels for power generation. This unique electrochemical technology offers high conversion efficiencies, produces proportionately less CO{sub 2} in capture-ready form, and does not consume or require water for gasification. FB-DCFC employs a specialized solid oxide fuel cell (SOFC) arrangement coupled to a Boudouard gasifier where the solid fuel particles are fluidized and reacted by the anode recycle gas CO{sub 2}. The resulting CO is electrochemically oxidized at the anode. Anode supported SOFC structures employed a porous Ni cermet anode layer, a dense yttria stabilized zirconia membrane, and a mixed conducting porous perovskite cathode film. Several kinds of untreated solid fuels (carbon and coal) were tested in bench scale FBDCFC prototypes for electrochemical performance and stability testing. Single cells of tubular geometry with active areas up to 24 cm{sup 2} were fabricated. The cells achieved high power densities up to 450 mW/cm{sup 2} at 850 C using a low sulfur Alaska coal char. This represents the highest power density reported in the open literature for coal based DCFC. Similarly, power densities up to 175 mW/cm{sup 2} at 850 C were demonstrated with carbon. Electrical conversion efficiencies for coal char were experimentally determined to be 48%. Long-term stability of cell performance was measured under galvanostatic conditions for 375 hours in CO with no degradation whatsoever, indicating that carbon deposition (or coking) does not pose any problems. Similar cell stability results were obtained in coal char tested for 24 hours under galvanostatic conditions with no sign of sulfur poisoning. Moreover, a 50-cell planar stack targeted for 1 kW output was fabricated and tested in 95% CO (balance CO{sub 2

Unburned carbon in combustion residues from mainly solid biofuels

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem H; Lind B; Lagerkvist A

2012-02-15

Unburned carbon in 21 combustion residues from solid biofuels is investigated using several methods of analysis (a.o. LOI and TOC), as well as micro-Raman spectroscopy. The results are used to discuss the distribution of unburned carbon in the residues from the different combustion plants and its nature (organic or elemental). The consequences of the elemental nature of carbon for environmental properties of the residue are noted

Heavy-ion irradiation induced diamond formation in carbonaceous materials

International Nuclear Information System (INIS)

Daulton, T. L.

1999-01-01

The basic mechanisms of metastable phase formation produced under highly non-equilibrium thermodynamic conditions within high-energy particle tracks are investigated. In particular, the possible formation of diamond by heavy-ion irradiation of graphite at ambient temperature is examined. This work was motivated, in part, by earlier studies which discovered nanometer-grain polycrystalline diamond aggregates of submicron-size in uranium-rich carbonaceous mineral assemblages of Precambrian age. It was proposed that the radioactive decay of uranium formed diamond in the fission particle tracks produced in the carbonaceous minerals. To test the hypothesis that nanodiamonds can form by ion irradiation, fine-grain polycrystalline graphite sheets were irradiated with 400 MeV Kr ions. The ion irradiated graphite (and unirradiated graphite control) were then subjected to acid dissolution treatments to remove the graphite and isolate any diamonds that were produced. The acid residues were then characterized by analytical and high-resolution transmission electron microscopy. The acid residues of the ion-irradiated graphite were found to contain ppm concentrations of nanodiamonds, suggesting that ion irradiation of bulk graphite at ambient temperature can produce diamond

Pair distribution functions of carbonaceous solids, determined using energy filtered diffraction

International Nuclear Information System (INIS)

Petersen, T.C.; McCulloch, D.G.

2002-01-01

Full text: The structures of various carbonaceous solids were investigated using energy filtered diffraction patterns collected in two dimensions using a Gatan Imaging Filter (GIF). In order to reduce multiple scattering and eliminate inelastic scattering effects, the diffraction patterns were filtered using an energy -selecting slit around the zero-loss peak. Software has been developed for the extraction of radially averaged pair distributions functions from the diffraction data. This entails finding the position of the un-scattered beam, radially averaging the two dimensional intensity distributions, calibrating the resulting one dimensional intensity profiles and finally normalising the data to obtain structure factors. Techniques for improving and assessing data quality, pertaining to the methodology used here, have also been explored. Structure factors and radial distribution functions generated using this analysis will be discussed and, for the commercial V25 glassy carbon samples, compared to previous, work of one of the authors'. In order to answer questions regarding multiple scattering effects and structural homogeneity of the samples, neutron scattering was performed on the Medium Resolution Powder Diffractometer (MRPD), at the Australian Nuclear Science and Technology's (ANSTO) facility. A critical comparison of the neutron scattering and electron diffraction generated structure factors will be presented. Copyright (2002) Australian Society for Electron Microscopy Inc

Characterization on incineration residue of radioactive solid wastes

International Nuclear Information System (INIS)

Katoh, Kiyoshi; Hirayama, Katsuyoshi; Kato, Akira.

1989-01-01

Characterization was carried out on incineration residue discharged from the radioactive solid waste incineration unit (capacity, 100 kg/h) in use at the Tokai Research Establishment of Japan Atomic Energy Research Institute (JAERI) to obtain basic data for investigating solidification methods of the residue. The characterized residue was taken from furnace and a primary ceramic filter of the incineration unit which incinerates combustible solid wastes generated at JAERI and the outside organizations. Items of characterization involve a particle size distribution, misplaced materials content, ignition loss, chemical composition and radioactivity of nuclides in the ash. As the results, the size of ash sampled from the furnace distributed a wide range, with about 35∼60 % of ash smaller than 5 mm and about 10∼25 % of massive one larger than 30 mm (max. size: ∼130 mm). The ignition loss was 2∼3 %. The chemical compositions of the ash were mainly SiO 2 , Fe 2 O 3 , CaO and Al 2 O 3 . The specific activities of the ash were about 0.4∼4 x 10 3 Bq/g, and principal contaminants were 60 Co and 137 Cs. (author)

Solid residues from Italian municipal solid waste incinerators: A source for "critical" raw materials.

Science.gov (United States)

Funari, Valerio; Braga, Roberto; Bokhari, Syed Nadeem Hussain; Dinelli, Enrico; Meisel, Thomas

2015-11-01

The incineration of municipal solid wastes is an important part of the waste management system along with recycling and waste disposal, and the solid residues produced after the thermal process have received attention for environmental concerns and the recovery of valuable metals. This study focuses on the Critical Raw Materials (CRM) content in solid residues from two Italian municipal waste incinerator (MSWI) plants. We sampled untreated bottom ash and fly ash residues, i.e. the two main outputs of common grate-furnace incinerators, and determined their total elemental composition with sensitive analytical techniques such as XRF and ICP-MS. After the removal of a few coarse metallic objects from bottom ashes, the corresponding ICP solutions were obtained using strong digestion methods, to ensure the dissolution of the most refractory components that could host significant amounts of precious metals and CRM. The integration of accurate chemical data with a substance flow analysis, which takes into account the mass balance and uncertainties assessment, indicates that bottom and fly ashes can be considered as a low concentration stream of precious and high-tech metals. The magnesium, copper, antimony and zinc contents are close to the corresponding values of a low-grade ore. The distribution of the elements flow between bottom and fly ash, and within different grain size fractions of bottom ash, is appraised. Most elements are enriched in the bottom ash flow, especially in the fine grained fractions. However, the calculated transfer coefficients indicate that Sb and Zn strongly partition into the fly ashes. The comparison with available studies indicates that the CRM concentrations in the untreated solid residues are comparable with those residues that undergo post-treatment beneficiations, e.g. separation between ferrous and non-ferrous fractions. The suggested separate collection of "fresh" bottom ash, which could be processed for further mineral upgrading, can

Anaerobic digestion of onion residuals using a mesophilic Anaerobic Phased Solids Digester

International Nuclear Information System (INIS)

Romano, Rowena T.; Zhang, Ruihong

2011-01-01

The anaerobic digestion of onion residual from an onion processing plant was studied under batch-fed and continuously-fed mesophilic (35 ± 2 o C) conditions in an Anaerobic Phased Solids (APS) Digester. The batch digestion tests were performed at an initial loading of 2.8 gVS L -1 and retention time of 14 days. The biogas and methane yields, and volatile solids reduction from the onion residual were determined to be 0.69 ± 0.06 L gVS -1 , 0.38 ± 0.05 L CH 4 gVS -1 , and 64 ± 17%, respectively. Continuous digestion tests were carried out at organic loading rates (OLRs) of 0.5-2.0 gVS L -1 d -1 . Hydrated lime (Ca(OH) 2 ) was added to the APS-Digester along with the onion residual at 16 mg Ca(OH) 2 gVS -1 to control the pH of the biogasification reactor above 7.0. At steady state the average biogas yields were 0.51, 0.56, and 0.62 L gVS -1 for the OLRs of 0.5, 1.0, and 2.0 gVS L -1 d -1 respectively. The methane yields at steady state were 0.29, 0.32, and 0.31 L CH 4 gVS -1 for the OLRs of 0.5, 1.0, and 2.0 gVS L -1 d -1 respectively. The study shows that the digestion of onion residual required proper alkalinity and pH control, which was possible through the use of caustic chemicals. However, such chemicals will begin to have an inhibitory effect on the microbial population at high loading rates, and therefore alternative operational parameters are needed. -- Highlights: → An APS-Digester was used to study biogas production from onion solid residues. → Biogas and methane yields from onion solids were determined. → Study showed substantial findings for treating onion solid residues.

Carbonaceous species (coke) characterization in zeolites by solid state {sup 13} C NMR; Caracterizacao de especies carbonaceas (coque) em zeolitos por RMN de {sup 13} C estado solido (CP/MAS)

Energy Technology Data Exchange (ETDEWEB)

Mota, Claudio J.A.; Menezes, Sonia C [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

1992-12-31

This work applies solid state {sup 13} C NMR for characterization of carbonaceous species (coke) deposited on zeolites after contact with n-hexane at 370 deg C. The results have shown two types of carbon: saturated (sp{sup 3}) and unsaturated (sp{sup 2}) 4 refs., 4 tabs.

Alternatives of Treatment and Final Disposition of the Solid Hospital residuals

International Nuclear Information System (INIS)

Meza Monge, K.

1998-01-01

The current handling, treatment and final disposition of the hospital solid waste in Costa Rica are considered inadequate or at least insufficient. This situation represents a serious danger for the population's health and the environment, because they are exposed to infectious agents, toxic substances and even radioactive products that are generated among the residuals of the centers of health. This work, alternatives propose for the treatment and adequate final disposition of the solid waste produced in the hospitals of the country. They take into consideration the characteristics that present these residuals, the advantages and disadvantages of each one of the existent techniques and the technical and economic possibilities of the country. For this purpose, in first instance, a revision about the properties, the quality and the quantity of the solid waste produced by the national hospital centers was carried out. Also, a diagnostic of the current situation of the treatment and final disposition of these residuals in some of the most important hospitals of the country, as well as of the possibilities of physical space with that they count on was carried out. Then, the existent different treatment techniques and final disposition for the solid waste that comes from the centers of health are described, as well as their advantages and disadvantages and a comparative analysis of the same ones is carried out. The objective is completed, since alternatives of treatment and final disposition that are considered appropriate for this type of residuals are planned. Nevertheless, in the future, more detailed investigations and studies of feasibility, with the purpose of developing handling programs and elimination of the solid waste for each one of the hospital centers in Costa Rica should be carried out. (Author) [es

Residual thermal stresses in a solid sphere cast from a thermosetting material

Science.gov (United States)

Levitsky, M.; Shaffer, B. W.

1975-01-01

Expressions are developed for the residual thermal stresses in a solid sphere cast from a chemically hardening thermosetting material in a rigid spherical mold. The description of the heat generation rate and temperature variation is derived from a first-order chemical reaction. Solidification is described by the continuous transformation of the material from an inviscid liquidlike state into an elastic solid, with intermediate properties determined by the degree of chemical reaction. Residual stress components are obtained as functions of the parameters of the hardening process and the properties of the hardening material. Variation of the residual stresses with a nondimensionalized reaction rate parameter and the relative compressibility of the hardened material is discussed in detail.

Conditioning of radioactive ash residue in a wave of solid-phase exothermal reactions

International Nuclear Information System (INIS)

Karlina, O.K.; Varlakova, G.A.; Ozhovan, M.I.; Tivanskij, V.M.; Dmitriev, S.A.

2001-01-01

The abilities for utilization of exothermic reaction heat in solid phase for conditioning the ash residue produced as a result of solid radioactive waste burning are analyzed. It is shown that the process of ash residue making monolithic with obtaining the glass-like finish product containing 50-60 mass % of ash residue which meets the requirements for solidified radioactive wastes may be realized without energy supplying from external heat sources. The conditioning is realized in a special crucible furnace-container designed not only for the process conducting but also for subsequent storage or disposal of the finish product [ru

Leaching from municipal solid waste incineration residues

Energy Technology Data Exchange (ETDEWEB)

Hyks, J.

2008-02-15

Leaching of pollutants from Municipal Solid Waste Incineration (MSWI) residues has been investigated combining a range of laboratory leaching experiments with geochemical modeling. Special attention was paid to assessing the applicability of laboratory data for subsequent modeling with respect to presumed full-scale conditions; both sample pretreatment and actual influence of leaching conditions on the results of laboratory experiments were considered. It was shown that sample pretreatment may have large impact on leaching test data. In particular, a significant fraction of Pb was shown mobile during the washing of residues with water. In addition, drying of residues (i.e. slow oxidation) prior to leaching experiments increased the leaching of Cr significantly. Significant differences regarding the leaching behavior of individual elements with respect to (non)equilibrium conditions in column percolation experiments were observed in the study. As a result, three groups of elements were identified based on the predominant leaching control and the influence of (non)equilibrium on the results of the laboratory column experiments: I. Predominantly availability-controlled elements (e.g. Na, K, Cl) II. Solubility-controlled elements (e.g. Ca, S, Si, Al, Ba, and Zn) III. Complexation-controlled elements (e.g. Cu and Ni) With respect to the above groups it was suggested that results of laboratory column experiments can, with consideration, be used to estimate full-scale leaching of elements from Group I and II. However, in order to avoid large underestimations in the assessment of leaching from Group III, it is imperative to describe the time-dependent transport of dissolved organic carbon (DOC) in the tested system or to minimize the physical non-equilibrium during laboratory experiments (e.g. bigger column, slower flow velocity). Forward geochemical modeling was applied to simulate long-term release of elements from a MSWI air-pollution-control residue. Leaching of a

Detailed monitoring of two biogas plants and mechanical solid-liquid separation of fermentation residues.

Science.gov (United States)

Bauer, Alexander; Mayr, Herwig; Hopfner-Sixt, Katharina; Amon, Thomas

2009-06-01

The Austrian "green electricity act" (Okostromgesetz) has led to an increase in biogas power plant size and consequently to an increased use of biomass. A biogas power plant with a generating capacity of 500 kW(el) consumes up to 38,000 kg of biomass per day. 260 ha of cropland is required to produce this mass. The high water content of biomass necessitates a high transport volume for energy crops and fermentation residues. The transport and application of fermentation residues to farmland is the last step in this logistic chain. The use of fermentation residues as fertilizer closes the nutrient cycle and is a central element in the efficient use of biomass for power production. Treatment of fermentation residues by separation into liquid and solid phases may be a solution to the transport problem. This paper presents detailed results from the monitoring of two biogas plants and from the analysis of the separation of fermentation residues. Furthermore, two different separator technologies for the separation of fermentation residues of biogas plants were analyzed. The examined biogas plants correspond to the current technological state of the art and have designs developed specifically for the utilization of energy crops. The hydraulic retention time ranged between 45.0 and 83.7 days. The specific methane yields were 0.40-0.43 m(3)N CH(4) per kg VS. The volume loads ranged between 3.69 and 4.00 kg VS/m(3). The degree of degradation was between 77.3% and 82.14%. The screw extractor separator was better suited for biogas slurry separation than the rotary screen separator. The screw extractor separator exhibited a high throughput and good separation efficiency. The efficiency of slurry separation depended on the dry matter content of the fermentation residue. The higher the dry matter content, the higher the proportion of solid phase after separation. In this project, we found that the fermentation residues could be divided into 79.2% fluid phase with a dry matter

Physicochemical pretreatments and hydrolysis of furfural residues via carbon-based sulfonated solid acid.

Science.gov (United States)

Ma, Bao Jun; Sun, Yuan; Lin, Ke Ying; Li, Bing; Liu, Wan Yi

2014-03-01

Potential commercial physicochemical pretreatment methods, NaOH/microwave and NaOH/ultrasound were developed, and the carbon-based sulfonated solid acid catalysts were prepared for furfural residues conversion into reducing sugars. After the two optimum pretreatments, both the content of cellulose increased (74.03%, 72.28%, respectively) and the content of hemicellulose (94.11%, 94.17% of removal rate, respectively) and lignin (91.75%, 92.09% of removal rate, respectively) decreased in furfural residues. The reducing sugar yields of furfural residues with the two physicochemical pretreatments on coal tar-based solid acid reached 33.94% and 33.13%, respectively, higher than that pretreated via NaOH alone (27%) and comparable to that pretreated via NaOH/H2O2 (35.67%). The XRD patterns, IR spectra and SEM images show microwave and ultrasound improve the pretreatment effect. The results demonstrate the carbon-based sulfonated solid acids and the physicochemical pretreatments are green, effective, low-cost for furfural residues conversion. Copyright © 2014 Elsevier Ltd. All rights reserved.

The Distinct Genetics of Carbonaceous and Non-Carbonaceous Meteorites Inferred from Molybdenum Isotopes

Science.gov (United States)

Budde, G.; Burkhardt, C.; Kleine, T.

2017-07-01

Mo isotope systematics manifest a fundamental dichotomy in the genetic heritage of carbonaceous and non-carbonaceous meteorites. We discuss its implications in light of the most recent literature data and new isotope data for primitive achondrites.

Destructive hydrogenation of carbonaceous material, etc

Energy Technology Data Exchange (ETDEWEB)

1938-07-30

A process is described for the destructive hydrogenation of solid distillable carbonaceous material, consisting of mixing the raw material in a paste by means of a mixture practically free from asphalt, from an oil obtained initially from the products coming out of the reaction space as vapor, particularly heavy oil, and oils obtained by pushing just to the state of pitch or coke the distillation of all the products which come out of the reaction space in any state but the vapor and which restrain some of the raw material intact and part of the products.

Characterisation of agroindustrial solid residues as biofuels and potential application in thermochemical processes.

Science.gov (United States)

Virmond, Elaine; De Sena, Rennio F; Albrecht, Waldir; Althoff, Christine A; Moreira, Regina F P M; José, Humberto J

2012-10-01

In the present work, selected agroindustrial solid residues from Brazil - biosolids from meat processing wastewater treatment and mixture of sawdust with these biosolids; residues from apple and orange juice industries; sugarcane bagasse; açaí kernels (Euterpe oleracea) and rice husk - were characterised as solid fuels and an evaluation of their properties, including proximate and ultimate composition, energy content, thermal behaviour, composition and fusibility of the ashes was performed. The lower heating value of the biomasses ranged from 14.31 MJkg(-1) to 29.14 MJkg(-1), on a dry and ash free basis (daf), all presenting high volatile matter content, varying between 70.57 wt.% and 85.36 wt.% (daf) what improves the thermochemical conversion of the solids. The fouling and slagging tendency of the ashes was predicted based on the fuel ash composition and on the ash fusibility correlations proposed in the literature, which is important to the project and operation of biomass conversion systems. The potential for application of the Brazilian agroindustrial solid residues studied as alternative energy sources in thermochemical processes has been identified, especially concerning direct combustion for steam generation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Porous carbonaceous electrode structure and method for secondary electrochemical cell

Science.gov (United States)

Kaun, Thomas D.

1977-03-08

Positive and negative electrodes are provided as rigid, porous carbonaceous matrices with particulate active material fixedly embedded. Active material such as metal chalcogenides, solid alloys of alkali metal or alkaline earth metals along with other metals and their oxides in particulate form are blended with a thermosetting resin and a solid volatile to form a paste mixture. Various electrically conductive powders or current collector structures can be blended or embedded into the paste mixture which can be molded to the desired electrode shape. The molded paste is heated to a temperature at which the volatile transforms into vapor to impart porosity as the resin begins to cure into a rigid solid structure.

Characterization of solid residues from coal liquefaction processes. Phase I

Energy Technology Data Exchange (ETDEWEB)

Potter, J.; McDougall, W.M.; Kybett, B.D.; Neufeld, C.

1981-01-01

Various coal liquefaction and beneficiation processes are being investigated by independent research groups sponsored by the Canadian Federal Government. These processes include the co-processing of heavy oils and bitumen with coal, oxygen removal and hydrogenation of coal and supercritical gas extraction of coal. The end products, gaseous and liquid fuels and insoluble organic residues, vary with the experimental conditions. The physical properties and origin of the insoluble residue may influence such factors as degree of conversion, efficiency of the process, and ultimately, gaseous and liquid yields. One of the most suitable methods of assessing the nature of the insoluble residues is the use of petrography. This report deals with petrographic assessment of the coals and residues from various coal conversion processes; attempts were made to characterize the solid phases in the residues; to assess them in a quantitative manner and where possible; to correlate the results with experimental data; and to assess their effects on conversion. (30 refs.)

Solid radioactive waste: evaluation of residual activity in nuclear medicine services

International Nuclear Information System (INIS)

Alabarse, Frederico G.; Xavier, Ana M.; Magalhaes, Maisa H.; Guerrero, Jesus S.P.

2009-01-01

An experimental programme to estimate, with a better degree of accuracy, the activity that remains adsorbed in flasks and syringes used in Nuclear Medicine Services for the administration of radionuclides to patients submitted to diagnostic or therapy is been conducted under the coordination of the Radioactive Waste Division of the Brazilian Nuclear Energy Commission, CNEN. The adopted recommendation in Brazil to allow an expedite solid waste management in nuclear medicine facilities, up to the present, is to consider that 2% of the initial activity remains adsorbed in the solid waste, which easily allows the calculation of the storage time to achieve regulatory clearance levels by decay. This research evaluates 17 different kinds of radiopharmaceuticals and three radioisotopes: 99m Tc, 67 Ga and 201 Tl. Results obtained by means of a weighting method to estimate the residual mass in flasks show that the ratio of the mass of the liquid that remains in the solid waste to the mass of the empty flask is constant. This suggests that the residual activity depends on the initial activity concentration of radiopharmaceutical contained in each flask, as assumed by the regulatory body. Additionally, results obtained by determining the remaining activity in flasks, shortly after the injection of its radionuclide contents in patients, indicate that an average value for the residual activity of the order of 10% of the initial activity contained in the flasks or syringes should be adopted to determine the decay storage time before the release of solid waste in the urban conventional land fill disposal system. The 'rule of thumb' of 10 half-lives for storage before clearance is also discussed in the present work. (author)

Use of Residual Solids from Pulp and Paper Mills for Enhancing Strength and Durability of Ready-Mixed Concrete

Energy Technology Data Exchange (ETDEWEB)

Tarun R. Naik; Yoon-moon Chun; Rudolph N. Kraus

2003-09-18

This research was conducted to establish mixture proportioning and production technologies for ready-mixed concrete containing pulp and paper mill residual solids and to study technical, economical, and performance benefits of using the residual solids in the concrete. Fibrous residuals generated from pulp and paper mills were used, and concrete mixture proportions and productions technologies were first optimized under controlled laboratory conditions. Based on the mixture proportions established in the laboratory, prototype field concrete mixtures were manufactured at a ready-mixed concrete plant. Afterward, a field construction demonstration was held to demonstrate the production and placement of structural-grade cold-weather-resistant concrete containing residual solids.

Preparation and Characterization of a Solid Acid Catalyst from Macro Fungi Residue for Methyl Palmitate Production

Directory of Open Access Journals (Sweden)

Min Wang

2015-07-01

Full Text Available During the process of fungal polysaccharide extraction for health care products and food factories, a large quantity of macro-fungi residues are produced, but most of the residues are abandoned and become environmental pollutants. A solid acid catalyst, prepared by sulfonating carbonized Phellinus igniarius residue, was shown to be an efficient and environmentally benign catalyst for the esterification of palmitate acid (PA and methanol. As a comparison, two types of common biomass catalysts, wheat straws and wood chips, were prepared. In this study, characterizations, including scanning electron microscopy, thermo-gravimetric analysis, Fourier transform infrared spectrometry, Brunauer-Emmett-Teller assays and elemental analysis, and reaction conditions for the synthesis of methyl palmitate (MP using solid acid catalysts were investigated. Experiments showed that the solid acid catalyst prepared from P. igniarius residue had a higher catalytic activity than the other two catalysts, and the highest yield of MP catalyzed by P. igniarius residue solid acid catalyst was 91.5% under the following optimum conditions: molar ratio of methanol/PA of 10:1, reaction temperature of 60 °C, mass ratio of catalyst/substrate of 2%, and a reaction time of 1.5 h. Thus, the use of this catalyst offers a method for producing MP.

Review of the technology for solar gasification of carbonaceous materials

International Nuclear Information System (INIS)

Epstein, M.; Spiewak, I.; Funken, K.H.; Ortner, J.

1994-01-01

Research has demonstrated the feasibility of solar assisted gasification of carbonaceous materials to form synthesis gas (syngas). The potential feedstocks range from natural gas, residual oil, biomass, and oil-shale to coal. The expected advantages of such processing are yields of syngas with calorific values above those of the carbonaceous feedstocks, syngas quality suited to production of hydrogen, methanol or bulk Fischer-Tropsch fuels, and the ability to process low-grade and waste materials with essentially no emissions to atmosphere other than small amounts of CO 2 . The review provides some background on solar receiver concepts to reach the high temperatures needed for syngas production, the basic chemistry involved, covers applicable experiments that have been reported with solar inputs and with conventional heating, heat transfer processes, process and energy balances, and cost analysis. Approximately 80 references are cited. The authors present their views on the most promising approaches to solar-assisted gasification, the technology development required, and the ultimate benefits of such development and commercialization

XPS and STEM studies of Allende acid insoluble residues

Science.gov (United States)

Housley, R. M.; Clarke, D. R.

1980-01-01

Data on Allende acid residues obtained both before and after etching with hot HNO3 are presented. X-ray photoelectron spectra show predominantly carbonaceous material plus Fe-deficient chromite in both cases. The HNO3 oxidizes the carbonaceous material to some extent. The small chromites in these residues have a wide range of compositions somewhat paralleling those observed in larger Allende chromites and in Murchison chromites, especially in the high Al contents; however, they are deficient in divalent cations, which makes them metastable and indicates that they must have formed at relatively low temperatures. It is suggested that they formed by precipitation of Cr(3+) and Fe(3+) from olivine at low temperature or during rapid cooling.

Determining the release of radionuclides from tank waste residual solids. FY2015 report

Energy Technology Data Exchange (ETDEWEB)

King, William D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hobbs, David T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-09-11

Methodology development for pore water leaching studies has been continued to support Savannah River Site High Level Waste tank closure efforts. For FY2015, the primary goal of this testing was the achievement of target pH and Eh values for pore water solutions representative of local groundwater in the presence of grout or grout-representative (CaCO₃ or FeS) solids as well as waste surrogate solids representative of residual solids expected to be present in a closed tank. For oxidizing conditions representative of a closed tank after aging, a focus was placed on using solid phases believed to be controlling pH and E_h at equilibrium conditions. For three pore water conditions (shown below), the target pH values were achieved to within 0.5 pH units. Tank 18 residual surrogate solids leaching studies were conducted over an E_h range of approximately 630 mV. Significantly higher Eh values were achieved for the oxidizing conditions (ORII and ORIII) than were previously observed. For the ORII condition, the target Eh value was nearly achieved (within 50 mV). However, E_h values observed for the ORIII condition were approximately 160 mV less positive than the target. E_h values observed for the RRII condition were approximately 370 mV less negative than the target. Achievement of more positive and more negative E_h values is believed to require the addition of non-representative oxidants and reductants, respectively. Plutonium and uranium concentrations measured during Tank 18 residual surrogate solids leaching studies under these conditions (shown below) followed the general trends predicted for plutonium and uranium oxide phases, assuming equilibrium with dissolved oxygen. The highest plutonium and uranium concentrations were observed for the ORIII condition and the lowest concentrations were observed for the RRII condition. Based on these results, it is recommended that these test methodologies be used to

Treating carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Kelly, T D

1927-07-29

Coal, lignite, shale, peat, or like carbonaceous material is heated at 70 to 300/sup 0/C with an alkaline solution of sodium, potassium, or ammonium oleate and aluminum sulfate is added in order to solidify the oleate. The solid material is separated and molded or shaped or disintegrated for use as a pigment or mixed with rubber or similar compounds such as solidified, oxidized or polymerized oils in making building blocks or tiles, tires, footwear, or other resilient material. It may be distilled with water or steam in a retort to make gas, or in porous condition can be burnt. The liquid products may be subjected to fractional distillation or mixed with bitumen, resin or oils or materials such as clay, red oxide, or barytes to give colour or body in the manufacture of waterproof heatproof dressings which may be made quick-drying by the addition of ammonia, or for mixing with or spreading over stones or on roads or concrete.

Biodrying of animal slaughterhouse residues and heat production

Energy Technology Data Exchange (ETDEWEB)

Bernard, Y. [Centre de recherche industrielle, Quebec City, PQ (Canada)

2010-07-01

Animal carcasses from slaughterhouses are usually composted on farms, but the composting process is not optimized and a large volumes of carbonaceous residues are needed. This type of composting takes place over a period of 6 to 9 months in a nonaerated static pile. Quebec's industrial research centre (CRIQ) developed an organic biodrying process (BIOSECO) adapted to large-scale operations in order to optimize the treatment of slaughterhouse residues. Biodrying is a form of composting, in which the thermophilic phase is optimized, making it possible to evaporate large amounts of water. Biodrying is done inside a building and reduces the amount of carbonaceous residues considerably. The process is optimized by the sequence in which the slaughterhouse residues are added, the choice of input and the aeration flow. Slaughterhouse residues can be treated non-stop throughout the entire year. Since the odours are nearly completed limited to the building, the biodrying can be done near the slaughterhouse. A large amount of heat was produced by the process during the pilot project. It was concluded that the BIOSECO biodrying process is suitable for treating slaughterhouse residues in an effective and economic manner, and has the added advantage of producing heat that could be used for various purposes.

Preparation of a Sulfonated Carbonaceous Material from Lignosulfonate and Its Usefulness as an Esterification Catalyst

Directory of Open Access Journals (Sweden)

Duckhee Lee

2013-07-01

Full Text Available Sulfonated carbonaceous material useful as a solid acid catalyst was prepared from lignosulfonate, a waste of the paper-making industry sulfite pulping process, and characterized by 13C-NMR, FT-IR, TGA, SEM and elemental analysis, etc. The sulfonic acid group density and total density of all acid groups in the sulfonated carbonaceous material was determined by titration to be 1.24 mmol/g and 5.90 mmol/g, respectively. Its catalytic activity in the esterification of cyclohexanecarboxylic acid with anhydrous ethanol was shown to be comparable to that of the ionic exchange resin Amberlyst-15, when they were used in the same amount. In the meantime, the sulfonic acid group was found to be leached out by 26%–29% after it was exposed to hot water (95 °C for 5 h. The catalytic usefulness of the prepared carbonaceous material was investigated by performing esterifications.

Carbonaceous material production from vegetable residue and their use in the removal of textile dyes present in wastewater

Science.gov (United States)

Peláez-Cid, A. A.; Tlalpa-Galán, M. A.; Herrera-González, A. M.

2013-06-01

This paper presents the adsorption results of acid, basic, direct, vat, and reactive-type dyes on carbonaceous adsorbent materials prepared starting off vegetable residue such as Opuntia ficus indica and Casimiroa edulis fruit wastes. The adsorbents prepared from Opuntia ficus indica waste were designated: TunaAsh, CarTunaT, and CarTunaQ. The materials obtained from Casimiroa edulis waste were named: CenZAP, CarZAPT, and CarZAPQ. TunaAsh and CenZAP consist of ashes obtained at 550 °C CarTunaT and CarZAPT consist of the materials carbonized at 400 °C lastly, CarTunaQ and CarZAPQ consist of chemically activated carbons using H3PO4 at 400 °C. Only the chemically activated materials were washed with distilled water until a neutral pH was obtained after their carbonization. All materials were ground and sieved to obtain a particle size ranging from 0.25 to 0.84 mm. The static adsorption results showed that both ashes and chemically activated carbon are more efficient at dye removal for both vegetable residues. For TunaAsh and CarTunaQ, removal rates of up to 100% in the cases of basic, acid, and direct dyes were achieved. Regarding wastewater containing reactive dyes, the efficiency ranged from 60 to 100%. For vat effluents, it ranged from 42 to 52%. In the case of CenZAP and CarZAPQ, it was possible to treat reactive effluents with rates ranging between 63 and 91%. Regarding vat effluents, it ranged from 57 to 68%. The process of characterization for all materials was done using scanning electron microscopy and infrared spectroscopy.

Carbonaceous material production from vegetable residue and their use in the removal of textile dyes present in wastewater

International Nuclear Information System (INIS)

Peláez-Cid, A A; Tlalpa-Galán, M A; Herrera-González, A M

2013-01-01

This paper presents the adsorption results of acid, basic, direct, vat, and reactive-type dyes on carbonaceous adsorbent materials prepared starting off vegetable residue such as Opuntia ficus indica and Casimiroa edulis fruit wastes. The adsorbents prepared from Opuntia ficus indica waste were designated: TunaAsh, CarTunaT, and CarTunaQ. The materials obtained from Casimiroa edulis waste were named: CenZAP, CarZAPT, and CarZAPQ. TunaAsh and CenZAP consist of ashes obtained at 550 °C; CarTunaT and CarZAPT consist of the materials carbonized at 400 °C; lastly, CarTunaQ and CarZAPQ consist of chemically activated carbons using H 3 PO 4 at 400 °C. Only the chemically activated materials were washed with distilled water until a neutral pH was obtained after their carbonization. All materials were ground and sieved to obtain a particle size ranging from 0.25 to 0.84 mm. The static adsorption results showed that both ashes and chemically activated carbon are more efficient at dye removal for both vegetable residues. For TunaAsh and CarTunaQ, removal rates of up to 100% in the cases of basic, acid, and direct dyes were achieved. Regarding wastewater containing reactive dyes, the efficiency ranged from 60 to 100%. For vat effluents, it ranged from 42 to 52%. In the case of CenZAP and CarZAPQ, it was possible to treat reactive effluents with rates ranging between 63 and 91%. Regarding vat effluents, it ranged from 57 to 68%. The process of characterization for all materials was done using scanning electron microscopy and infrared spectroscopy.

Obtaining Low Rank Coal Biotransforming Bacteria from Microhabitats Enriched with Carbonaceous Residues

International Nuclear Information System (INIS)

Valero Valero, Nelson; Rodriguez Salazar, Luz Nidia; Mancilla Gomez, Sandra; Contreras Bayona, Leydis

2012-01-01

Bacteria capable of low rank coal (LRC) biotransform were isolated from environmental samples altered with coal in the mine The Cerrejon. A protocol was designed to select strains more capable of LRC biotransform, the protocol includes isolation in a selective medium with LRC powder, qualitative and quantitative tests for LRC solubilization in solid and liquid culture medium. Of 75 bacterial strains isolated, 32 showed growth in minimal salts agar with 5 % carbon. The strains that produce higher values of humic substances (HS) have a mechanism of solubilization associated with pH changes in the culture medium, probably related to the production of extracellular alkaline substances by bacteria. The largest number of strains and bacteria with more solubilizing activity on LRC were isolated from sludge with high content of carbon residue and rhizosphere of Typha domingensis and Cenchrus ciliaris grown on sediments mixed with carbon particles, this result suggests that obtaining and solubilization capacity of LRC by bacteria may be related to the microhabitat where the populations originated.

Destructive hydrogenation of carbonaceous materials, etc

Energy Technology Data Exchange (ETDEWEB)

1938-02-15

A process is described for the destructive hydrogenation continuously of solid and infusible carbonaceous substances, consisting of heating the charge to the same temperature as the added hydrogen, under a pressure essentially equal to that of the reaction, from the first to at least 300/sup 0/C, but not more than 440/sup 0/C, while passing the heated charge through a zone the contents of which are equal to about 20 per cent to 40 per cent of that of the reaction space, maintaining the charge for a certain time at the temperature without sensible change in the pressure, then reheating the charge to at least the temperature to prime the reaction and finally to introduce the charge into the reaction space.

Carbonaceous deposits on naptha reforming catalysts

International Nuclear Information System (INIS)

Redwan, D.S.

1999-01-01

Carbonaceous deposits on naphtha reforming catalysts play a decisive role in limiting process performance. The deposits negatively after catalyst activity, selectivity and the production cycle of a semi regenerative reformer. The magnitude of negative effect of those deposits is directly proportional to their amounts and complexity. Investigations on used reforming catalysts samples reveal that the amount and type (complexity of the chemical nature) of carbonaceous deposits are directly proportional to the catalysts life on stream and the severity of operating conditions. In addition, the combustibility behavior of carbonaceous deposits on the catalyst samples taken from different reformers are found to be different. Optimal carbon removal, for in situ catalyst regeneration, requires the specific conditions be developed, based on the results of well designed and properly performed investigations of the amount and type of carbonaceous deposits. (author)

Typical Mexican agroindustrial residues as supports for solid-state fermentation

DEFF Research Database (Denmark)

Flores-Maltos, Dulce A.; Mussatto, Solange Ines; Contreras Esquivel, Juan Carlos

2014-01-01

. These biological wastes can be used as support-substrates in Solid-State Fermentation (SSF) to produce industrially relevant metabolites with great economical advantage. In addition, it is an environment friendly method of waste management. In this study were analyzed six different Mexican agro industrial residues...... process. The results provided important knowledge about the characteristics of these materials revealing their potential for use in fermentation processes....

Carbon-based strong solid acid for cornstarch hydrolysis

Science.gov (United States)

Nata, Iryanti Fatyasari; Irawan, Chairul; Mardina, Primata; Lee, Cheng-Kang

2015-10-01

Highly sulfonated carbonaceous spheres with diameter of 100-500 nm can be generated by hydrothermal carbonization of glucose in the presence of hydroxyethylsulfonic acid and acrylic acid at 180 °C for 4 h. The acidity of the prepared carbonaceous sphere C4-SO3H can reach 2.10 mmol/g. It was used as a solid acid catalyst for the hydrolysis of cornstarch. Total reducing sugar (TRS) concentration of 19.91 mg/mL could be obtained by hydrolyzing 20 mg/mL cornstarch at 150 °C for 6 h using C4-SO3H as solid acid catalyst. The solid acid catalyst demonstrated good stability that only 9% decrease in TRS concentration was observed after five repeat uses. The as-prepared carbon-based solid acid catalyst can be an environmentally benign replacement for homogeneous catalyst.

Treatment of mine water and solid residues (RS) in San Rafael mining and milling complex

International Nuclear Information System (INIS)

Asenjo, Armando R.; Perrino, Juan F.

2006-01-01

San Rafael Mining and Milling Complex is located in Mendoza Province, in San Rafael Department, 38 km West from San Rafael city and 240 km south from Mendoza city, capital of the province. Activities related with yellow cake production were performed from 1979 to 1999. Nowadays the mine and the plant are in stand by. At the moment technical, economic and environmental studies are being done in order to restart the activities. Different kind of residues are accumulated in the site: a) Tailing; b) Sludges; c) Low grade ores; e) Waste rock; f) Mine water; g) Solid residues (RS). In this paper methodology to treat mine water and solid residues (RS) will be informed. a) Mine water: 800.000 m 3 of mine water are accumulated in different open pit. Uranium, radium and arsenic are the main ions to take into account to treat the water. Several laboratory and pilot test have been performed in order to define the treatment of the water, according with the regulatory requirement. A methodology using anion exchange resin to fix uranium and precipitation using barium chloride and iron sulfate to separate radium and arsenic has been developed. b) Solid residues (RS): these residues (precipitates) have been produced by neutralization of effluents in a nuclear purification process (TBP process). They are accumulated in drums. These residues come from Cordoba plant, a factory which produces UO 2 powder. The total content of uranium in the precipitate is 14.249 kg with an average uranium concentration of 1,33%. A methodology using sulfuric acid dissolution of the precipitates and anion exchange resin to recovery the uranium has been developed. (author) [es

Field effect transistors and photodetectors based on nanocrystalline graphene derived from electron beam induced carbonaceous patterns

International Nuclear Information System (INIS)

Kurra, Narendra; Bhadram, Venkata Srinu; Narayana, Chandrabhas; Kulkarni, G U

2012-01-01

We describe a transfer-free method for the fabrication of nanocrystalline graphene (nc-graphene) on SiO 2 substrates directly from patterned carbonaceous deposits. The deposits were produced from the residual hydrocarbons present in the vacuum chamber without any external source by using an electron beam induced carbonaceous deposition (EBICD) process. Thermal treatment under vacuum conditions in the presence of Ni catalyst transformed the EBIC deposit into nc-graphene patterns, confirmed using Raman and TEM analysis. The nc-graphene patterns have been employed as an active p-type channel material in a field effect transistor (FET) which showed a hole mobility of ∼90 cm 2 V −1 s −1 . The nc-graphene also proved to be suitable material for IR detection. (paper)

Nitrile versus isonitrile adsorption at interstellar grain surfaces. II. Carbonaceous aromatic surfaces

Science.gov (United States)

Bertin, M.; Doronin, M.; Michaut, X.; Philippe, L.; Markovits, A.; Fillion, J.-H.; Pauzat, F.; Ellinger, Y.; Guillemin, J.-C.

2017-12-01

Context. Almost 20% of the 200 different species detected in the interstellar and circumstellar media present a carbon atom linked to nitrogen by a triple bond. Of these 37 molecules, 30 are nitrile R-CN compounds, the remaining 7 belonging to the isonitrile R-NC family. How these species behave in their interactions with the grain surfaces is still an open question. Aims: In a previous work, we have investigated whether the difference between nitrile and isonitrile functional groups may induce differences in the adsorption energies of the related isomers at the surfaces of interstellar grains of various nature and morphologies. This study is a follow up of this work, where we focus on the adsorption on carbonaceous aromatic surfaces. Methods: The question is addressed by means of a concerted experimental and theoretical approach of the adsorption energies of CH3CN and CH3NC on the surface of graphite (with and without surface defects). The experimental determination of the molecule and surface interaction energies is carried out using temperature-programmed desorption in an ultra-high vacuum between 70 and 160 K. Theoretically, the question is addressed using first-principle periodic density functional theory to represent the organised solid support. Results: The adsorption energy of each compound is found to be very sensitive to the structural defects of the aromatic carbonaceous surface: these defects, expected to be present in a large numbers and great diversity on a realistic surface, significantly increase the average adsorption energies to more than 50% as compared to adsorption on perfect graphene planes. The most stable isomer (CH3CN) interacts more efficiently with the carbonaceous solid support than the higher energy isomer (CH3NC), however.

Compostagem da fração sólida da água residuária de suinocultura Solid fraction composting of residual water from pig farms

Directory of Open Access Journals (Sweden)

Marco A. P. Orrico Júnior

2009-09-01

Full Text Available Avaliar o desenvolvimento do processo de compostagem utilizando como substrato à fração sólida da água residuária de suinocultura foi o objetivo deste trabalho. Para a obtenção da fração sólida, a água residuária de suinocultura foi submetida ao peneiramento, utilizando-se de peneira com malha de 1 milímetro. Após separação, a fração sólida foi utilizada para a confecção de três leiras de compostagem, em pátio com piso de concreto e cobertura plástica. Durante a compostagem da fração sólida da água residuária de suinocultura, foram avaliados: temperatura, reduções de sólidos totais (ST, sólidos voláteis (SV, demanda química de oxigênio (DQO, carbono orgânico, matéria orgânica compostável (MOC, matéria orgânica resistente à compostagem (MORC, números mais prováveis (NMPs de coliformes totais e coliformes termotolerantes, além do volume e dos teores de nutrientes no composto. A compostagem mostrou-se eficiente no tratamento da fração sólida da água residuária de suinocultura devido à elevada minimização do poder poluente dos dejetos, observando-se reduções de 71,24% nos teores de ST, 64,55% no volume, 56,89% no teor de DQO e 56,89% na MOC. Foram verificadas reduções de 100% nos NMPs de coliformes totais e termotolerantes, o que possibilita seu uso como adubo orgânico.This work aimed to evaluate the development of the composting process by using the solid fraction of residual water from a pig farm. To obtain the solid fraction, the residual water was sewed in a 1mm screen sew. After separation, the solid fraction was used to form three composting piles, on a patio with concrete floor and plastic cover. During composting the solid fraction of residual water from pig farms was monitored: temperature, total solids reduction (TS, volatile solids (VS chemical demand for oxygen (CDO, organic carbon, compostable organic matter (COM, organic matter resistant to composting (OMRC, most probable

STUDY OF ASPHALT BINDER OIL RESIDUE AND MUNICIPAL SOLID WASTE ASH TO BE USED IN LOW TRAFFIC PAVEMENTS

Directory of Open Access Journals (Sweden)

Michéle Dal Toé Casagrande

2014-12-01

Full Text Available The great generation of urban solid has been a concern in several countries. This work presents a study with two materials: the asphalt binder oil residue accumulated in the bottom of asphalt tanks and the municipal solid waste ash, to be used, respectively, as a substitute of conventional binder in asphalt mixtures and for soil stabilization in pavements base layers. Were evaluated properties as the mechanical behavior of the mixtures through experimental tests. The results show the potential of incorporating these residues for low traffic roads, allowing the construction of low cost roads and an environmental use of the residue.

Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic

International Nuclear Information System (INIS)

Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

2008-01-01

The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 deg. C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic.

Science.gov (United States)

Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

2008-08-15

The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 degrees C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

Carbonaceous electrode materials for supercapacitors.

Science.gov (United States)

Hao, Long; Li, Xianglong; Zhi, Linjie

2013-07-26

Supercapacitors have been widely studied around the world in recent years, due to their excellent power density and long cycle life. As the most frequently used electrode materials for supercapacitors, carbonaceous materials attract more and more attention. However, their relatively low energy density still holds back the widespread application. Up to now, various strategies have been developed to figure out this problem. This research news summarizes the recent advances in improving the supercapacitor performance of carbonaceous materials, including the incorporation of heteroatoms and the pore size effect (subnanopores' contribution). In addition, a new class of carbonaceous materials, porous organic networks (PONs) has been managed into the supercapacitor field, which promises great potential in not only improving the supercapacitor performances, but also unraveling the related mechanisms. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Global cloud condensation nuclei influenced by carbonaceous combustion aerosol

Directory of Open Access Journals (Sweden)

D. V. Spracklen

2011-09-01

Full Text Available Black carbon in carbonaceous combustion aerosol warms the climate by absorbing solar radiation, meaning reductions in black carbon emissions are often perceived as an attractive global warming mitigation option. However, carbonaceous combustion aerosol can also act as cloud condensation nuclei (CCN so they also cool the climate by increasing cloud albedo. The net radiative effect of carbonaceous combustion aerosol is uncertain because their contribution to CCN has not been evaluated on the global scale. By combining extensive observations of CCN concentrations with the GLOMAP global aerosol model, we find that the model is biased low (normalised mean bias = −77 % unless carbonaceous combustion aerosol act as CCN. We show that carbonaceous combustion aerosol accounts for more than half (52–64 % of global CCN with the range due to uncertainty in the emitted size distribution of carbonaceous combustion particles. The model predicts that wildfire and pollution (fossil fuel and biofuel carbonaceous combustion aerosol causes a global mean cloud albedo aerosol indirect effect of −0.34 W m⁻², with stronger cooling if we assume smaller particle emission size. We calculate that carbonaceous combustion aerosol from pollution sources cause a global mean aerosol indirect effect of −0.23 W m⁻². The small size of carbonaceous combustion particles from fossil fuel sources means that whilst pollution sources account for only one-third of the emitted mass they cause two-thirds of the cloud albedo aerosol indirect effect that is due to carbonaceous combustion aerosol. This cooling effect must be accounted for, along with other cloud effects not studied here, to ensure that black carbon emissions controls that reduce the high number concentrations of fossil fuel particles have the desired net effect on climate.

Characterization of Solids in Residual Wastes from Single-Shell Tanks at the Hanford Site, Washington, USA - 9277

International Nuclear Information System (INIS)

Krupka, Kenneth M.; Cantrell, Kirk J.; Schaef, Herbert T.; Arey, Bruce W.; Heald, Steve M.; Deutsch, William J.; Lindberg, Michael J.

2009-01-01

Solid-phase characterization methods have been used in an ongoing study of residual wastes (i.e., waste remaining after final retrieval operations) from the underground single-shell storage tanks 241-C-103, 241-C-106, 241-C-202, 241-C-203, and 241-S-112 at the U.S. Department of Energy's Hanford Site in Washington State. The results of studies completed to date show significant variability in the compositions of those residual wastes and the compositions, morphologies, and crystallinities of the individual phases that make up these wastes. These differences undoubtedly result from the various waste types stored and transferred in and out each tank and the sluicing and retrieval operations used for waste retrieval. Our studies indicate that these residual wastes are chemically-complex assemblages of crystalline and amorphous solids that contain contaminants as discrete phases and/or co-precipitated within oxide phases. Depending on the specific tank, various solids (e.g., gibbsite; boehmite; dawsonite; cancrinite; Fe oxides such as hematite, goethite, and maghemite; rhodochrosite; lindbergite; whewellite; nitratine; and numerous amorphous or poorly crystalline phases) have been identified by X-ray diffraction and scanning electron microscopy/energy dispersive X-ray spectroscopy in residual wastes studied to date. Our studies also show that contact of residual wastes with Ca(OH)2- and CaCO3-saturated aqueous solutions, which were used as surrogates for the compositions of pore-fluid leachants derived from young and aged cements respectively, may alter the compositions of solid phases present in the contacted wastes. Fe oxides/hydroxides have been identified in all residual wastes studied to date. They occur in these wastes as discrete particles, particles intergrown within a matrix of other phases, and surface coatings on other particles or particle aggregates. These Fe oxides/hydroxides typically contain trace concentrations of other transition metals, such Cr, Mn

Carbon-based strong solid acid for cornstarch hydrolysis

Energy Technology Data Exchange (ETDEWEB)

Nata, Iryanti Fatyasari, E-mail: yanti_tkunlam@yahoo.com [Chemical Engineering Study Program, Faculty of Engineering, Lambung Mangkurat University, Jl. A. Yani Km. 36 Banjarbaru, South Kalimantan 70714 (Indonesia); Irawan, Chairul; Mardina, Primata [Chemical Engineering Study Program, Faculty of Engineering, Lambung Mangkurat University, Jl. A. Yani Km. 36 Banjarbaru, South Kalimantan 70714 (Indonesia); Lee, Cheng-Kang, E-mail: cklee@mail.ntust.edu.tw [Department of Chemical Engineering, National Taiwan University of Science and Technology, 43 Keelung Rd. Sec.4, Taipei 106, Taiwan (China)

2015-10-15

Highly sulfonated carbonaceous spheres with diameter of 100–500 nm can be generated by hydrothermal carbonization of glucose in the presence of hydroxyethylsulfonic acid and acrylic acid at 180 °C for 4 h. The acidity of the prepared carbonaceous sphere C4-SO{sub 3}H can reach 2.10 mmol/g. It was used as a solid acid catalyst for the hydrolysis of cornstarch. Total reducing sugar (TRS) concentration of 19.91 mg/mL could be obtained by hydrolyzing 20 mg/mL cornstarch at 150 °C for 6 h using C4-SO{sub 3}H as solid acid catalyst. The solid acid catalyst demonstrated good stability that only 9% decrease in TRS concentration was observed after five repeat uses. The as-prepared carbon-based solid acid catalyst can be an environmentally benign replacement for homogeneous catalyst. - Highlights: • Carbon solid acid was successfully prepared by one-step hydrothermal carbonization. • The acrylic acid as monomer was effectively reduce the diameter size of particle. • The solid acid catalyst show good catalytic performance of starch hydrolysis. • The solid acid catalyst is not significantly deteriorated after repeated use.

Carbon-based strong solid acid for cornstarch hydrolysis

International Nuclear Information System (INIS)

Nata, Iryanti Fatyasari; Irawan, Chairul; Mardina, Primata; Lee, Cheng-Kang

2015-01-01

Highly sulfonated carbonaceous spheres with diameter of 100–500 nm can be generated by hydrothermal carbonization of glucose in the presence of hydroxyethylsulfonic acid and acrylic acid at 180 °C for 4 h. The acidity of the prepared carbonaceous sphere C4-SO 3 H can reach 2.10 mmol/g. It was used as a solid acid catalyst for the hydrolysis of cornstarch. Total reducing sugar (TRS) concentration of 19.91 mg/mL could be obtained by hydrolyzing 20 mg/mL cornstarch at 150 °C for 6 h using C4-SO 3 H as solid acid catalyst. The solid acid catalyst demonstrated good stability that only 9% decrease in TRS concentration was observed after five repeat uses. The as-prepared carbon-based solid acid catalyst can be an environmentally benign replacement for homogeneous catalyst. - Highlights: • Carbon solid acid was successfully prepared by one-step hydrothermal carbonization. • The acrylic acid as monomer was effectively reduce the diameter size of particle. • The solid acid catalyst show good catalytic performance of starch hydrolysis. • The solid acid catalyst is not significantly deteriorated after repeated use

Determining the Release of Radionuclides from Tank 18F Waste Residual Solids: FY2016 Report

Energy Technology Data Exchange (ETDEWEB)

King, William D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hobbs, David T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-08-12

Pore water leaching studies were conducted on actual Savannah River Site (SRS) Tank 18F residual waste solids to support Liquid Waste tank closure efforts. A test methodology was developed during previous simulant testing to produce slurries of tank residual solids and grout-representative solids in grout pore water solutions (based on SRS groundwater compositions) with pH and E_h values expected during the aging of the closed waste tank. The target conditions are provided below where the initial pore water has a reducing potential and a relatively high pH (Reducing Region II). The pore water is expected to become increasingly oxidizing with time (Oxidizing Region II) and during the latter stages of aging (Oxidizing Region III) the pH is expected to decrease. For the reducing case, tests were conducted with both unwashed and washed Tank 18F residual solids. For the oxidizing cases (Oxidizing Regions II and III), all samples were washed with simulated grout pore water solutions prior to testing, since it is expected that these conditions will occur after considerable pore water solution has passed through the system. For the reducing case, separate tests were conducted with representative ground grout solids and with calcium carbonate reagent, which is the grout phase believed to be controlling the pH. Ferrous sulfide (FeS) solids were also added to the reducing samples to lower the slurry E_h value. Calcium carbonate solids were used as the grout-representative solid phase for each of the oxidizing cases. Air purge-gas with and without CO₂ removed was transferred through the oxidizing test samples and nitrogen purge-gas was transferred through the reducing test samples during leach testing. The target pH values were achieved to within 0.5 pH units for all samples. Leaching studies were conducted over an E_h range of approximately 0.7 V. However, the highest and lowest E_h values achieved of ~+0.5 V and ~-0.2 V were

Extraction products of solid carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

1937-11-04

A method is described for the manufacture of liquid products from pressure extracts of solid carbon-containing material by destructive hydrogenation, characterized in that the pressure extracts are hydrogenated in admixture with products of high-molecular weight formed during a previous destructive hydrogenation of another part of the same or other pressure extract and which has been collected as liquid without extensive cooling of the hot products of the reaction, which came from the reaction chamber where the previous destructive hydrogenation took place.

Evaluation of solid residues removed from a mangrove swamp in the São Vicente Estuary, SP, Brazil.

Science.gov (United States)

Cordeiro, C A M M; Costa, T M

2010-10-01

Mangrove swamps are found in estuaries along the coastal plains of tropical regions and have be subjected to heavy occupation and use pressure due to their privileged locations and abundance of biological resources. The present work evaluated the ecological characteristics and solid wastes accumulated in eight areas along the Santos - São Vicente Estuary Complex. The superficially deposited residues at each sampling site were collected and subsequently washed, drained, counted, weighed and separated into classes according to their composition and predominant use. The predominant litter type in terms of density was plastic (62.81%) and, by weight, wood (55.53%). The greatest deposition of residues was associated with areas that were less inclined and that had low plant density levels, indicating that the presence of obstacles was not critical for retaining floating residues in mangrove areas. The presence of the most frequently encountered types of solid waste residues could be explained by local activities. Copyright © 2010 Elsevier Ltd. All rights reserved.

Enhanced extraction of phenolic compounds from coffee industry’s residues through solid state fermentation by Penicillium purpurogenum

Directory of Open Access Journals (Sweden)

Lady Rossana PALOMINO García

2015-01-01

Full Text Available Abstract The use of agroindustrial residues is an economical solution to industrial biotechnology. Coffee husk and pulp are abounding residues from coffee industry which can be used as substrates in solid state fermentation process, thus allowing a liberation and increase in the phenolic compound content with high added value. By employing statistical design, initial moisture content, pH value in the medium, and the incubation temperature were evaluated, in order to increase the polyphenol content in a process of solid state fermentation by Penicillium purpurogenum. The main phenolic compounds identified through HPLC in fermented coffee residue were chlorogenic acid, caffeic acid, and rutin. Data obtained through HPLC with the radical absorbance capacity assay suggest the fermented coffee husk and pulp extracts potential as a source of phenolic acids and flavonoids. Results showed good perspectives when using P. purpurogenum strain to enhance the liberation of phenolic compounds in coffee residues.

Lab-scale pyrolysis of the Automotive Shredder Residue light fraction and characterization of tar and solid products.

Science.gov (United States)

Anzano, Manuela; Collina, Elena; Piccinelli, Elsa; Lasagni, Marina

2017-06-01

The general aim of this study is the recovery of Automotive Shredder Residue (ASR). The ASR light fraction, or car fluff, that was collected at an Italian shredding plant was pyrolysed at various temperatures (500-800°C) in a lab-scale reactor. The condensable gases (tar) and solid residue yields increased with decreasing temperature, and these products were characterized to suggest a potential use to reclaim them. The higher heating value (HHV) of tar was 34-37MJ/kg, which is comparable with those of fossil fuels. Furthermore, the ash content was low (0.06-4.98%). Thus, tar can be used as an alternative fuel. With this prospect, the concentrations of polychlorinated dibenzodioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in tar were determined. The toxicity of tar changes with temperature (1-5ng I-TEQ/g), and the PCDFs significantly contribute to tar toxicity, which was 75-100% with a maximum of 99.6% at 700°C. Regarding the characterization of the solid residue, the low HHV (2.4-3.3MJ/kg) does not make it suitable for energy recovery. Regarding material recovery, we considered its use as a filler in construction materials or a secondary source for metals. It shows a high metal concentration (280,000-395,000mg/kg), which is similar at different pyrolysis temperatures. At 500°C, polycyclic aromatic hydrocarbons (PAHs) were not detected in the solid residue, whereas the maximum total PAH concentration (19.41ng/g, 700°C) was lower than that in fly ash from MSWI. In conclusion, 500°C is a suitable pyrolysis temperature to obtain valuable tar and solid residue. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterization of carbonaceous matter in xenolithic clasts from the Sharps (H3.4) meteorite: Constraints on the origin and thermal processing

Energy Technology Data Exchange (ETDEWEB)

Kebukawa, Yoko [Yokohama National Univ. (Japan); Zolensky, Michael E. [NASA Johnson Space Center, Houston, TX (United States); Chan, Queenie H. S. [NASA Johnson Space Center, Houston, TX (United States); Nagao, Keisuke [Univ. of Tokyo (Japan); Kilcoyne, A. L. David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Bodnar, Robert J. [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Farley, Charles [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Rahman, Zia [NASA Johnson Space Center, Houston, TX (United States); Le, Loan [NASA Johnson Space Center, Houston, TX (United States); Cody, George D. [Carnegie Inst. of Washington, Washington, DC (United States)

2016-09-25

Primitive xenolithic clasts, often referred to as “dark clasts”, are well known in many regolith breccias. The Sharps H3.4 ordinary chondrite contains unusually large dark clasts up to ~1 cm across. Poorly-graphitized carbon (PGC), with Fe, Ni metal and described as “carbon-rich aggregates”, has been found in these clasts (Brearley, 1990). We report detailed analyses of carbonaceous matter in several identical Sharps clasts using FTIR, Raman, C-XANES, and TEM that provide insight on the extent of thermal processing and possible origin of such clasts. We also prepared acid residues of the clasts using the HCl/HF method and conducted mass spectrometric analysis of the entrained noble gases. Carbonaceous matter is often used to infer thermal history due to its sensitivity to thermal processes. The FTIR spectra of the acid residue from the Sharps clast suggest that carbonaceous matter in the clast contains less hydrogen and oxygen compared to acid residues from typical type 3.4 ordinary chondrites. The metamorphic temperatures obtained by Raman spectroscopy ranges between ~380 °C and ~490 °C. TEM observations indicate that the clasts experienced a peak temperature of 300 °C to 400 °C, based on the carbon d 002 layer lattice spacing of C-rich aggregates. These estimates are consistent with an earlier estimate of 330 ± 50 °C, that is also estimated by the d 002 layer lattice spacing (Brearley, 1990). It should be noted that the lattice spacing thermometer is based on terrestrial metamorphose rocks, and thus temperature was probably underestimated. Meanwhile, the C-XANES spectra of the C-rich aggregates show high exciton intensities, indicative of graphene structures that developed at around 700–800 °C following an extensive period of time (millions of years), however, the surrounding matrix areas experienced lower temperatures of less than 300–500 °C. Noble gas analysis of the acid residue from the Sharps clasts shows that the residue is

Reactor performance and energy analysis of solid state anaerobic co-digestion of dairy manure with corn stover and tomato residues.

Science.gov (United States)

Li, Yangyang; Xu, Fuqing; Li, Yu; Lu, Jiaxin; Li, Shuyan; Shah, Ajay; Zhang, Xuehua; Zhang, Hongyu; Gong, Xiaoyan; Li, Guoxue

2018-03-01

Anaerobic co-digestion is commonly believed to be benefical for biogas production. However, additional of co-substrates may require additional energy inputs and thus affect the overall energy efficiency of the system. In this study, reactor performance and energy analysis of solid state anaerobic digestion (SS-AD) of tomato residues with dairy manure and corn stover were investigated. Different fractions of tomato residues (0, 20, 40, 60, 80 and 100%, based on volatile solid weight (VS)) were co-digested with dairy manure and corn stover at 15% total solids. Energy analysis based on experimental data was conducted for three scenarios: SS-AD of 100% dairy manure, SS-AD of binary mixture (60% dairy manure and 40% corn stover, VS based), and SS-AD of ternary mixture (36% dairy manure, 24% corn stover, and 40% tomato residues, VS based). For each scenario, the energy requirements for individual process components, including feedstock collection and transportation, feedstock pretreatment, biogas plant operation, digestate processing and handling, and the energy production were examined. Results showed that the addition of 20 and 40% tomato residues increased methane yield compared to that of the dairy manure and corn stover mixture, indicating that the co-digestion could balance nutrients and improve the performance of solid-state anaerobic digestion. The energy required for heating substrates had the dominant effect on the total energy consumption. The highest volatile solids (VS) reduction (57.0%), methane yield (379.1 L/kg VS feed ), and net energy production were achieved with the mixture of 24% corn stover, 36% dairy manure, and 40% tomato residues. Thus, the extra energy input for adding tomato residues for co-digestion could be compensated by the increase of methane yield. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enzyme treatment to decrease solids and improve digestion of ...

African Journals Online (AJOL)

The aim of anaerobic digestion of primary sewage sludge is to convert the carbonaceous material contained in the solids into methane and carbon dioxide. The products of digestion are therefore gases, stabilised sludge solids which are subsequently dewatered and disposed of, and sludge liquor which is generally further ...

Distilling carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Ironside, T G

1921-09-01

In the distillation of carbonaceous material such as shale, coal, lignite, wood or liquid hydrocarbons, the material is mixed with a heated granular substance such as sand which supplies the necessary heat. The shale or the like, which may be preheated, is fed from a hopper by a worm conveyer to a tube leading into a retort, and the heated granular material such as sand is supplied from a jacketed container through a tube. On the lower end of a rotary shaft are radial arms to which are fixed angularly disposed blades which serve to mix the shale and hot sand and deliver the residue to a central discharge pipe closed at the bottom by a conical valve which opens when the weight of the superimposed material is sufficient. The distillates are taken off by an outlet. Steam vapor or gas may be supplied to the retort, preferably through a hollow shaft leading to hollow stirrers perforated to permit of the gas passing into the material. The retort may be externally heated by hot gases in the space surrounding the retort, and the latter may be divided by horizontal floors so that the material is caused to funnel from the periphery to the center of the floor, then through a central opening on to the floor next below, and from the center to the periphery of this floor, and so on.

Solid Phase Microextraction (SPME in Determination of Pesticide Residues in Soil Samples

Directory of Open Access Journals (Sweden)

Rada Đurović

2011-01-01

Full Text Available The basic principles and application possibilities of the methods based on solid phase microextraction (SPME in the analysis of pesticide residues in soil samples are presented in the paper. The most important experimental parameters which affect SPME efficacy inpesticide determination (type and thickness of microextraction fiber, duration of microextraction,temperature at which it is conducted, effect of addition of salts (the effect of efflorescence,temperature and time of desorption, the choice of optimal solvent for pesticide exctraction from the soil and the optimal number of extraction steps, as well as general guidelines for their optimization are also shown. In the end, current applications of SPMEmethods in the analysis of pesticide residues in soil samples are presented.

Comparison of various pretreatments for ethanol production enhancement from solid residue after rumen fluid digestion of rice straw.

Science.gov (United States)

Zhang, Haibo; Zhang, Panyue; Ye, Jie; Wu, Yan; Liu, Jianbo; Fang, Wei; Xu, Dong; Wang, Bei; Yan, Li; Zeng, Guangming

2018-01-01

The rumen digested residue of rice straw contains high residual carbohydrates, which makes it a potential cellulosic ethanol feedstock. This study evaluated the feasibility and effectiveness of applying microwave assisted alkali (MAP), ultrasound assisted alkali (UAP), and ball milling pretreatment (BMP) to enhance ethanol production from two digested residues (2.5%-DR and 10%-DR) after rumen fluid digestion of rice straw at 2.5% and 10.0% solid content. Results revealed that 2.5%-DR and 10%-DR had a cellulose content of 36.4% and 41.7%, respectively. MAP and UAP improved enzymatic hydrolysis of digested residue by removing the lignin and hemicellulose, while BMP by decreasing the particle size and crystallinity. BMP was concluded as the suitable pretreatment, resulting in an ethanol yield of 116.65 and 147.42mgg -1 for 2.5%-DR and 10%-DR, respectively. The integrated system including BMP for digested residue at 2.5% solid content achieved a maximum energy output of 7010kJkg -1 . Copyright © 2017 Elsevier Ltd. All rights reserved.

Municipal solid waste options : integrating organics management and residual disposal treatment : executive summary

Energy Technology Data Exchange (ETDEWEB)

Cant, M. (comp.) [Totten Sims Hubicki Associates Ltd., Calgary, AB (Canada); Van der Werf, P. [2cg Inc., Edmonton, AB (Canada); Kelleher, M. [Kelleher Environmental, Toronto, ON (Canada); Merriman, D. [MacViro Consultants, Markham, ON (Canada); Fitcher, K. [Gartner Lee Ltd., Toronto, ON (Canada); MacDonald, N. [CH2M Hill Engineering Ltd., Calgary, AB (Canada)

2006-04-15

The Municipal Solid Waste (MSW) Options Report explored different MSW management options for 3 community sizes: 20,000, 80,000 and 200,0000 people. It was released at a time when many communities were developing waste management plans to cost-effectively reduce environmental impacts and conserve landfill capacity. The purpose of this report was to provide a greater understanding on the environmental, social, economic, energy recovery/utilization and greenhouse gas (GHG) considerations of MSW management. The report also demonstrated the interrelationships between the management of organics and residuals. It was based on information from existing waste diversion and organics management options and emerging residual treatment technology options. The following organics management and residual treatment disposal options were evaluated: composting; anaerobic digestion; sanitary landfills; bioreactor landfills; and thermal treatment. Composting was examined with reference to both source separated organics (SSO) and mixed waste composting. SSO refers to the separation of materials suitable for composting solid waste from households, while mixed waste composting refers to the manual or mechanical removal of recyclable material from the waste, including compost. The composting process was reviewed along with available technologies such as non-reactor windrow; aerated static pile; reactor enclosed channel; and, container tunnel. An evaluation of SSO and mixed waste composting was then presented in terms of environmental, social, financial and GHG impacts. refs., tabs., figs.

Recovery of Rare Earth Elements from Solid Residue of El-Sela Ore, South Eastern Desert, Egypt

International Nuclear Information System (INIS)

Salman, A.A.; Sharaby, C.M.; Elnagar, W.A.; Khawassek, Y.M.; Abdo, Sh.M.

2015-01-01

The study area of Gabal El Sela at Halaib environ is located at about 20 km west of Abu Ramad City, Egypt. An uraniferous ore material associated with REE was subjected to sulphuric acid leaching for extraction of uranium mainly followed by solid liquid separation through filtration then washing. Physical upgrading was performed upon the dry residue. Chemical treatment by 50% NaOH was carried out where about 250 g residue ground at - 200 mesh were agitated at solid / liquid ratio of 1/2 for one hour. The cake was filtered then dri ed at 100 º C . T he dried cake was subject ed to dissolution by conc. HCl at 80 º C at a solid / liquid ratio 1:1 for one hour . More than 98% of REE was leached out , and then the leach liquor was subjected to selective precipitation by HF and oxalic acid then calcination of REE oxalate

Analysis of hazardous organic residues from sodium hydrosulfite industry and utilization as raw materials in a novel solid lubricant production

International Nuclear Information System (INIS)

Shang, Jiwu; Zhang, Yihe; Zhou, Fengshan; Lv, Fengzhu; Han, Feng; Lu, Jinbo; Meng, Xianghai; Chu, Paul K.; Ye, Zhengfang; Xing, Jing

2011-01-01

Highlights: ► The hazardous organic residual wastes produced by the sodium hydrosulfite industry are analyzed and the main compounds are found to be thiodiglycol and 2,2′-dithiodiethanol. ► The lubricity of the organic residues is subsequently studied and the homemade solid lubricant is observed to have good lubricity. ► The clean process is expected to not only have commercial impact but also help to reduce environmental pollution. - Abstract: The hazardous organic residual wastes produced by the sodium hydrosulfite industry are demonstrated to be convertible into a novel solid lubricant. Identification and isolation of the organic residues are achieved by Fourier transform infrared (FTIR) spectroscopy, gas chromatography–mass spectrometry (GC–MS), and nuclear magnetic resonance (NMR). FTIR and GC–MS provide important information about the residues and the two main components obtained by column chromatography are further analyzed by NMR. The main organic residues are found to be thiodiglycol and 2,2′-dithiodiethanol which have potential applications in petroleum drilling because of their S–S and/or C–S functional groups. The lubricity of the organic residues is subsequently studied and the influence of different adsorbents on the lubricity is investigated and discussed. This homemade lubricant is observed to have good lubricity and by increasing the concentration of the commercial solid lubricant M, the lubricity diminishes. The process is expected to not only have commercial impact but also help to reduce environmental pollution.

Analysis of hazardous organic residues from sodium hydrosulfite industry and utilization as raw materials in a novel solid lubricant production

Energy Technology Data Exchange (ETDEWEB)

Shang, Jiwu [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Zhang, Yihe, E-mail: zyh@cugb.edu.cn [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Zhou, Fengshan; Lv, Fengzhu; Han, Feng; Lu, Jinbo; Meng, Xianghai [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China); Chu, Paul K. [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Ye, Zhengfang [Department of Environmental Engineering, Key Laboratory of Water and Sediment Sciences of the Ministry of Education, Peking University, Beijing 100871 (China); Xing, Jing [State Key Laboratory of Geological Processes and Mineral Resources, National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083 (China)

2011-12-30

Highlights: Black-Right-Pointing-Pointer The hazardous organic residual wastes produced by the sodium hydrosulfite industry are analyzed and the main compounds are found to be thiodiglycol and 2,2 Prime -dithiodiethanol. Black-Right-Pointing-Pointer The lubricity of the organic residues is subsequently studied and the homemade solid lubricant is observed to have good lubricity. Black-Right-Pointing-Pointer The clean process is expected to not only have commercial impact but also help to reduce environmental pollution. - Abstract: The hazardous organic residual wastes produced by the sodium hydrosulfite industry are demonstrated to be convertible into a novel solid lubricant. Identification and isolation of the organic residues are achieved by Fourier transform infrared (FTIR) spectroscopy, gas chromatography-mass spectrometry (GC-MS), and nuclear magnetic resonance (NMR). FTIR and GC-MS provide important information about the residues and the two main components obtained by column chromatography are further analyzed by NMR. The main organic residues are found to be thiodiglycol and 2,2 Prime -dithiodiethanol which have potential applications in petroleum drilling because of their S-S and/or C-S functional groups. The lubricity of the organic residues is subsequently studied and the influence of different adsorbents on the lubricity is investigated and discussed. This homemade lubricant is observed to have good lubricity and by increasing the concentration of the commercial solid lubricant M, the lubricity diminishes. The process is expected to not only have commercial impact but also help to reduce environmental pollution.

Measurement of conformational constraints in an elastin-mimetic protein by residue-pair selected solid-state NMR

International Nuclear Information System (INIS)

Hong, Mei; McMillan, R. Andrew; Conticello, Vincent P.

2002-01-01

We introduce a solid-state NMR technique for selective detection of a residue pair in multiply labeled proteins to obtain site-specific structural constraints. The method exploits the frequency-offset dependence of cross polarization to achieve 13 CO i → 15 N i → 13 Cα i transfer between two residues. A 13 C, 15 N-labeled elastin mimetic protein (VPGVG) n is used to demonstrate the method. The technique selected the Gly3 Cα signal while suppressing the Gly5 Cα signal, and allowed the measurement of the Gly3 Cα chemical shift anisotropy to derive information on the protein conformation. This residue-pair selection technique should simplify the study of protein structure at specific residues

Distribution and Thermal Maturity of Devonian Carbonate Reservoir Solid Bitumen in Desheng Area of Guizhong Depression, South China

Directory of Open Access Journals (Sweden)

Yuguang Hou

2017-01-01

Full Text Available The distribution of solid bitumen in the Devonian carbonate reservoir from well Desheng 1, Guizhong Depression, was investigated by optical microscope and hydrocarbon inclusions analysis. Vb and chemical structure indexes measured by bitumen reflectance, laser Raman microprobe (LRM, and Fourier transform infrared spectroscopy (FTIR were carried out to determine the thermal maturity of solid bitumen. Based on the solid bitumen thermal maturity, the burial and thermal maturity history of Devonian carbonate reservoir were reconstructed by basin modeling. The results indicate that the fractures and fracture-related dissolution pores are the main storage space for the solid bitumen. The equivalent vitrinite reflectance of solid bitumen ranges from 3.42% to 4.43% converted by Vb (% and LRM. The infrared spectroscopy analysis suggests that there are no aliphatic chains detected in the solid bitumen which is rich in aromatics C=C chains (1431–1440 cm−1. The results of Vb (%, LRM, and FTIR analysis demonstrate that the solid bitumen has experienced high temperature and evolved to the residual carbonaceous stage. The thermal evolution of Devonian reservoirs had experienced four stages. The Devonian reservoirs reached the highest reservoir temperature 210–260°C during the second rapid burial-warming stage, which is the main period for the solid bitumen formation.

Utilization of agroindustrial residues for lipase production by solid-state fermentation

OpenAIRE

Damaso, M?nica Caramez Triches; Passianoto, Mois?s Augusto; de Freitas, Sidin?a Cordeiro; Freire, Denise Maria Guimar?es; Lago, Regina Celi Araujo; Couri, Sonia

2008-01-01

The aim of this work was to produce lipases by solid-state fermentation (SSF) using, as substrate, agroindustrial residue supplemented with by-products from corn oil refining process or olive oil. For a group of ten fungi strains selected in the first steps, the lipase activity obtained by SSF varied from 7.7 to 58.6 U/g of dry substrate (gds). Among the evaluated strains, the Aspergillus niger mutant 11T53A14 was selected by presenting the best enzymatic production. For the fermentation test...

Abodes for life in carbonaceous asteroids?

Science.gov (United States)

Abramov, Oleg; Mojzsis, Stephen J.

2011-05-01

Thermal evolution models for carbonaceous asteroids that use new data for permeability, pore volume, and water circulation as input parameters provide a window into what are arguably the earliest habitable environments in the Solar System. Plausible models of the Murchison meteorite (CM) parent body show that to first-order, conditions suitable for the stability of liquid water, and thus pre- or post-biotic chemistry, could have persisted within these asteroids for tens of Myr. In particular, our modeling results indicate that a 200-km carbonaceous asteroid with a 40% initial ice content takes almost 60 Myr to cool completely, with habitable temperatures being maintained for ˜24 Myr in the center. Yet, there are a number of indications that even with the requisite liquid water, thermal energy sources to drive chemical gradients, and abundant organic "building blocks" deemed necessary criteria for life, carbonaceous asteroids were intrinsically unfavorable sites for biopoesis. These controls include different degrees of exothermal mineral hydration reactions that boost internal warming but effectively remove liquid water from the system, rapid (1-10 mm yr -1) inward migration of internal habitable volumes in most models, and limitations imposed by low permeabilities and small pore sizes in primitive undifferentiated carbonaceous asteroids. Our results do not preclude the existence of habitable conditions on larger, possibly differentiated objects such as Ceres and the Themis family asteroids due to presumed longer, more intense heating and possible long-lived water reservoirs.

Conversion of agroindustrial residues for high poly(γ-glutamic acid) production by Bacillus subtilis NX-2 via solid-state fermentation.

Science.gov (United States)

Tang, Bao; Xu, Hong; Xu, Zongqi; Xu, Cen; Xu, Zheng; Lei, Peng; Qiu, Yibin; Liang, Jinfeng; Feng, Xiaohai

2015-04-01

Poly(γ-glutamic acid) (γ-PGA) production by Bacillus subtilis NX-2 was carried out through solid-state fermentation with dry mushroom residues (DMR) and monosodium glutamate production residues (MGPR; a substitute of glutamate) for the first time. Dry shiitake mushroom residue (DSMR) was found to be the most suitable solid substrate among these DMRs; the optimal DSMR-to-MGPR ratio was optimized as 12:8. To increase γ-PGA production, industrial waste glycerol was added as a carbon source supplement to the solid-state medium. As a result, γ-PGA production increased by 34.8%. The batch fermentation obtained an outcome of 115.6 g kg(-1) γ-PGA and 39.5×10(8) colony forming units g(-1) cells. Furthermore, a satisfactory yield of 107.7 g kg(-1) γ-PGA was achieved by compost experiment on a scale of 50 kg in open air, indicating that economically large-scale γ-PGA production was feasible. Therefore, this study provided a novel method to produce γ-PGA from abundant and low-cost agroindustrial residues. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparison of gas-solid chromatography and MM2 force field molecular binding energies for greenhouse gases on a carbonaceous surface.

Science.gov (United States)

Rybolt, Thomas R; Bivona, Kevin T; Thomas, Howard E; O'Dell, Casey M

2009-10-01

Gas-solid chromatography was used to determine B(2s) (gas-solid virial coefficient) values for eight molecular adsorbates interacting with a carbon powder (Carbopack B, Supelco). B(2s) values were determined by multiple size variant injections within the temperature range of 313-553 K. The molecular adsorbates included: carbon dioxide (CO(2)); tetrafluoromethane (CF(4)); hexafluoroethane (C(2)F(6)); 1,1-difluoroethane (C(2)H(4)F(2)); 1-chloro-1,1-difluoroethane (C(2)H(3)ClF(2)); dichlorodifluoromethane (CCl(2)F(2)); trichlorofluoromethane (CCl(3)F); and 1,1,1-trichloroethane (C(2)H(3)Cl(3)). Two of these molecules are of special interest because they are "super greenhouse gases". The global warming potential, GWP, for CF(4) is 6500 and for C(2)F(6) is 9200 relative to the reference value of 1 for CO(2). The GWP index considers both radiative blocking and molecular lifetime. For these and other industrial greenhouse gases, adsorptive trapping on a carbonaceous solid, which depends on molecule-surface binding energy, could avoid atmospheric release. The temperature variations of the gas-solid virial coefficients in conjunction with van't Hoff plots were used to find the experimental adsorption energy or binding energy values (E(*)) for each adsorbate. A molecular mechanics based, rough-surface model was used to calculate the molecule-surface binding energy (Ecal(*)) using augmented MM2 parameters. The surface model consisted of parallel graphene layers with two separated nanostructures each containing 17 benzene rings arranged in linear strips. The separation of the parallel nanostructures had been optimized in a prior study to appropriately represent molecule-surface interactions for Carbopack B. Linear regressions of E(*) versus Ecal(*) for the current data set of eight molecules and the same surface model gave E(*)=0.926 Ecal(*) and r(2)=0.956. A combined set of the current and prior Carbopack B adsorbates studied (linear alkanes, branched alkanes, cyclic alkanes

Effects of Sludge Dry Solid Content and Residual Bulking Agents on Volatile Solids Reduction Using Eisenia foetida

Directory of Open Access Journals (Sweden)

Mohammad ali Abdoli

2009-06-01

Full Text Available In the first stage of this study, the compound effects of sludge dry solid content and residual bulking agent type (paper, saw dust, straw mixed with activated sludge (10, 15, and 20% dry solids on volatile solids (V.S. reduction were investigated using Eisenia foetida in pilot scale experiments with batches of fifty earthworms in each of the 10 experimental treatments over a period of 10 weeks. The maximum V.S. reduction was attained in the mixture of sludge and paper, with a D.S. of 15% (0.42 ± 0.03 % day-1 while the minimum V.S. reduction was achieved in the mixture of sludge and straw, with a D.S. of 10% (0.26 ± 0.01 % day-1. In the second stage, the survival of Eisenia foetida in the anaerobic sewage sludge was investigated. In the unmixed raw anaerobic sludge, all the earthworms died during the first 9 weeks of the study period due to acute toxicity. From week 10, however, their survival rate improved so that by week 12 when toxicity reduced to 25.40%, they completely survived. This is while in the mixture of anaerobic sludge with paper (D.S. 15%, 100% of the earthworms survived from week 8 after the volatile solids reduced to 20.42% and 17.40%.

Metal releases from a municipal solid waste incineration air pollution control residue mixed with compost.

Science.gov (United States)

Van Praagh, M; Persson, K M

2008-08-01

The influence of 10 wt.% mature compost was tested on the heavy metal leachate emissions from a calcium-rich municipal solid waste incineration air pollution control residue (MSWI APC). Apart from elongated columns (500 and 1250 mm), an otherwise norm compliant European percolation test setup was used. More than 99% of the metals Al, As, Cd, Cr, Cu, Fe and Ni were left in the APC residue after leaching to a liquid-to-solid ratio (L/S) of 10. Apparent short-term effects of elevated leachate DOC concentrations on heavy metal releases were not detected. Zn and Pb leachate concentrations were one order of magnitude lower for L/S 5 and 10 from the pure APC residue column, which suggests a possible long-term effect of compost on the release of these elements. Prolonging the contact time between the pore water and the material resulted in elevated leachate concentrations at L/S 0.1 to L/S 1 by a factor of 2. Only Cr and Pb concentrations were at their maxima in the first leachates at L/S 0.1. Equilibrium speciation modelling with the PHREEQC code suggested portlandite (Ca(OH)2) to control Ca solubility and pH.

Woody residues and solid waste wood available for recovery in the United States, 2002

Science.gov (United States)

David B. McKeever; Robert H. Falk

2004-01-01

Large amounts of woody residues and solid wood waste are generated annually in the United States from the extraction of timber from forests, from forestry cultural operations, in the conversion of forest land to nonforest uses, in the initial processing of roundwood timber into usable products, in the construction and demolition of buildings and structures, and in the...

Carbonaceous Survivability on Impact

Science.gov (United States)

Bunch, T. E.; Becker, Luann; Morrison, David (Technical Monitor)

1994-01-01

In order to gain knowledge about the potential contributions of comets and cosmic dust to the origin of life on Earth, we need to explore the survivability of their potential organic compounds on impact and the formation of secondary products that may have arisen from the chaotic events sustained by the carriers as they fell to Earth. We have performed a series of hypervelocity impact experiments using carbon-bearing impactors (diamond, graphite, kerogens, PAH crystals, and Murchison and Nogoya meteorites) into Al plate targets at velocities - 6 km/s. Estimated peak shock pressures probably did not exceed 120 GPa and peak shock temperatures were probably less than 4000 K for times of nano- to microsecs. Nominal crater dia. are less than one mm. The most significant results of these experiments are the preservation of the higher mass PAHs (e. g., pyrene relative to napthalene) and the formation of additional alkylated PAHs. We have also examined the residues of polystyrene projectiles impacted by a microparticle accelerator into targets at velocities up to 15 km/s. This talk will discuss the results of these experiments and their implications with respect to the survival of carbonaceous deliverables to early Earth. The prospects of survivability of organic molecules on "intact" capture of cosmic dust in space via soft: and hard cosmic dust collectors will also be discussed.

Measurement of conformational constraints in an elastin-mimetic protein by residue-pair selected solid-state NMR

Energy Technology Data Exchange (ETDEWEB)

Hong, Mei [Iowa State University, Department of Chemistry (United States)], E-mail: mhong@iastate.edu; McMillan, R. Andrew; Conticello, Vincent P. [Emory University, Department of Chemistry (United States)

2002-02-15

We introduce a solid-state NMR technique for selective detection of a residue pair in multiply labeled proteins to obtain site-specific structural constraints. The method exploits the frequency-offset dependence of cross polarization to achieve {sup 13}CO{sub i} {sup {yields}} {sup 15}N{sub i} {sup {yields}} {sup 13}C{alpha}{sub i} transfer between two residues. A {sup 13}C, {sup 15}N-labeled elastin mimetic protein (VPGVG){sub n} is used to demonstrate the method. The technique selected the Gly3 C{alpha} signal while suppressing the Gly5 C{alpha} signal, and allowed the measurement of the Gly3 C{alpha} chemical shift anisotropy to derive information on the protein conformation. This residue-pair selection technique should simplify the study of protein structure at specific residues.

Metallic elements fractionation in municipal solid waste incineration residues

Science.gov (United States)

Kowalski, Piotr R.; Kasina, Monika; Michalik, Marek

2016-04-01

Municipal solid waste incineration (MSWI) residues are represented by three main materials: bottom ash, fly ash and air pollution control (APC) residues. Among them ˜80 wt% is bottom ash. All of that materials are products of high temperature (>1000° C) treatment of waste. Incineration process allows to obtain significant reduction of waste mass (up to 70%) and volume (up to 90%) what is commonly used in waste management to reduce the amount need to be landfilled or managed in other way. Incineration promote accumulation non-combustible fraction of waste, which part are metallic elements. That type of concentration is object of concerns about the incineration residues impact on the environment and also gives the possibility of attempts to recover them. Metallic elements are not equally distributed among the materials. Several factors influence the process: melting points, volatility and place and forms of metallic occurrence in the incinerated waste. To investigate metallic elements distribution in MSWI residues samples from one of the biggest MSW incineration plant in Poland were collected in 2015. Chemical analysis with emphasis on the metallic elements content were performed using inductively coupled plasma optical emission (ICP-OES) and mass spectrometry (ICP-MS). The bottom ash was a SiO2-CaO-Al2O3-Fe2O3-Na2O rich material, whereas fly ash and APC residues were mostly composed of CaO and SiO2. All of the materials were rich in amorphous phase occurring together with various, mostly silicate crystalline phases. In a mass of bottom ash 11 wt% were metallic elements but also in ashes 8.5 wt% (fly ash) and ˜4.5 wt% (APC residues) of them were present. Among the metallic elements equal distribution between bottom and fly ash was observed for Al (˜3.85 wt%), Mn (770 ppm) and Ni (˜65 ppm). In bottom ash Fe (5.5 wt%), Cr (590 ppm) and Cu (1250 ppm) were concentrated. These values in comparison to fly ash were 5-fold higher for Fe, 3-fold for Cu and 1.5-fold for

Evaluation of residual activity of solid waste generated in nuclear medicine services of Porto Alegre - Brazil

International Nuclear Information System (INIS)

Xavier, Ana M.; Alabarse, Frederico Gil; Magalhaes, Maisa Haiidamus; Guerrero, Jesus Salvador Perez

2008-01-01

An experimental programme to estimate, with a better degree of accuracy, the activity that remains adsorbed in flasks and syringes used in Nuclear Medicine Services for the administration of radionuclides to patients submitted to diagnostic or therapy was conducted under the coordination of the Radioactive Waste Division of the Brazilian Nuclear Energy Commission. The adopted recommendation in Brazil to allow an expedite solid waste management in nuclear medicine facilities, up to the present, is to consider that 2% of the initial activity remains adsorbed in the solid waste, which easily allows the calculation of the storage time to achieve regulatory clearance levels by decay. This research evaluates 17 different kinds of radio pharmaceuticals and three radioisotopes: 99m Tc, 67 Ga and 201 Tl. Results obtained by means of a weighting method to estimate the residual mass in flasks show that the ratio of the mass of the liquid that remains in the solid waste to the mass of the empty flask is constant. This suggests that the residual activity depends on the initial activity concentration of radiopharmaceutical contained in each flask, as assumed by the regulatory body. Additionally, results obtained by determining the remaining activity in flasks, shortly after the injection of its radionuclides contents in patients, indicate that an average value for the residual activity of the order of 10% of the initial activity contained in the flasks or syringes can be adopted instead of the previously assumed 2%. It is suggested that the more conservative average value obtained in the present work for the activity that remains in flasks and syringes, that is, 10% of the initial activity, could be adopted to determine the decay storage time before the release of solid waste in the urban conventional land fill disposal system. (author)

Making coke

Energy Technology Data Exchange (ETDEWEB)

Wodehouse-Temple, C G

1929-07-12

Semi-coke is produced by mixing low-value absorbent solid carbonaceous material such as coal dust, slack, gas-works coke, lignite, torbanite, raphilite, cannel, or shale with not more than 20% of a carbonaceous binding material such as petroleum distillation residue, tarry residues, pitch bitumen, Trinidad asphalt, Manjak or the substance known under the registered Trade Mark Gilsonite and subjecting the mixture without briquetting to a temperature not exceeding 550/sup 0/C. According to the first Provisional Specification, the mixture may if desired be briquetted before being heated and the second constituent may be present to the extent of 30%.

Morphology, composition, and mixing state of primary particles from combustion sources ? crop residue, wood, and solid waste

OpenAIRE

Liu, Lei; Kong, Shaofei; Zhang, Yinxiao; Wang, Yuanyuan; Xu, Liang; Yan, Qin; Lingaswamy, A. P.; Shi, Zongbo; Lv, Senlin; Niu, Hongya; Shao, Longyi; Hu, Min; Zhang, Daizhou; Chen, Jianmin; Zhang, Xiaoye

2017-01-01

Morphology, composition, and mixing state of individual particles emitted from crop residue, wood, and solid waste combustion in a residential stove were analyzed using transmission electron microscopy (TEM). Our study showed that particles from crop residue and apple wood combustion were mainly organic matter (OM) in smoldering phase, whereas soot-OM internally mixed with K in flaming phase. Wild grass combustion in flaming phase released some Cl-rich-OM/soot particles and cardboard combusti...

A process for treatment of residues from dry/semidry APC systems at municipal solid waste incinerators. Final report

Energy Technology Data Exchange (ETDEWEB)

Hjelmar, O. [VKI, Hoersholm (Denmark)] Holland, D. [FLS miljoe a/s, Valby (Denmark)] Poulsen, B. [KARA, Roskilde (Denmark)

1997-08-01

The main objective of the project has been to establish and test a process for treatment of residues from the semidry (and dry) lime injection based APC processes at MSWIs, which will ensure that the residues can be managed in an environmentally safe manner. In pursuit of this goal, the following activities have been carried out: Performance of pilot scale extractions (approximately 50 kg of residue per batch) at the KARA MSWI in Roskilde of semidry APC system residues in order to establish and optimize process conditions. The optimization includes consideration of the possibilities for subsequent treatment/stabilization of the extracted solid phase as well as the possibility of treatment and safe discharge/utilization of the extract; Performance of chemical characterization, hydrogeochemical model calculations and experimental work in order to improve the understanding of the mechanisms and factors which for several contaminants control the equilibrium between the solid and liquid phases, both in the short and the long germ, and to use this information to obtain an environmentally acceptable method for stabilization/treatment of the extracted residues while at the same time minimizing the necessary amount of additives; production of treated residues and performance of leaching tests on these to assess and demonstrate the effectiveness of the entire process (extraction + stabilization/treatment); Evaluation of the technical, economical and environmental consequences of full scale implementation of the process. (EG) EFP-94. 19 refs.

Origin and abundance of water in carbonaceous asteroids

Science.gov (United States)

Marrocchi, Yves; Bekaert, David V.; Piani, Laurette

2018-01-01

The origin and abundance of water accreted by carbonaceous asteroids remains underconstrained, but would provide important information on the dynamic of the protoplanetary disk. Here we report the in situ oxygen isotopic compositions of aqueously formed fayalite grains in the Kaba and Mokoia CV chondrites. CV chondrite bulk, matrix and fayalite O-isotopic compositions define the mass-independent continuous trend (δ17O = 0.84 ± 0.03 × δ18O - 4.25 ± 0.1), which shows that the main process controlling the O-isotopic composition of the CV chondrite parent body is related to isotopic exchange between 16O-rich anhydrous silicates and 17O- and 18O-rich fluid. Similar isotopic behaviors observed in CM, CR and CO chondrites demonstrate the ubiquitous nature of O-isotopic exchange as the main physical process in establishing the O-isotopic features of carbonaceous chondrites, regardless of their alteration degree. Based on these results, we developed a new approach to estimate the abundance of water accreted by carbonaceous chondrites (quantified by the water/rock ratio) with CM (0.3-0.4) ≥ CR (0.1-0.4) ≥ CV (0.1-0.2) > CO (0.01-0.10). The low water/rock ratios and the O-isotopic characteristics of secondary minerals in carbonaceous chondrites indicate they (i) formed in the main asteroid belt and (ii) accreted a locally derived (inner Solar System) water formed near the snowline by condensation from the gas phase. Such results imply low influx of D- and 17O- and 18O-rich water ice grains from the outer part of the Solar System. The latter is likely due to the presence of a Jupiter-induced gap in the protoplanetary disk that limited the inward drift of outer Solar System material at the exception of particles with size lower than 150 μm such as presolar grains. Among carbonaceous chondrites, CV chondrites show O-isotopic features suggesting potential contribution of 17-18O-rich water that may be related to their older accretion relative to other hydrated

Wet, Carbonaceous Asteroids: Altering Minerals, Changing Amino Acids

Science.gov (United States)

Taylor, G. J.

2011-04-01

Many carbonaceous chondrites contain alteration products from water-rock interactions at low temperature and organic compounds. A fascinating fact known for decades is the presence in some of them of an assortment of organic compounds, including amino acids, sometimes called the building blocks of life. Murchison and other CM carbonaceous chondrites contain hundreds of amino acids. Early measurements indicated that the amino acids in carbonaceous chondrites had equal proportions of L- and D-structures, a situation called racemic. This was in sharp contrast to life on Earth, which heavily favors L- forms. However, beginning in 1997, John Cronin and Sandra Pizzarello (Arizona State University) found L- excesses in isovaline and several other amino acids in the Murchison carbonaceous chondrite. In 2009, Daniel Glavin and Jason Dworkin (Astrobiology Analytical Lab, Goddard Space Flight Center) reported the first independent confirmation of L-isovaline excesses in Murchison using a different analytical technique than employed by Cronin and Pizzarello. Inspired by this work, Daniel Glavin, Michael Callahan, Jason Dworkin, and Jamie Elsila (Astrobiology Analytical Lab, Goddard Space Flight Center), have done an extensive study of the abundance and symmetry of amino acids in carbonaceous chondrites that experienced a range of alteration by water in their parent asteroids. The results show that amino acids are more abundant in the less altered meteorites, implying that aqueous processing changes the mix of amino acids. They also confirmed the enrichment in L-structures of some amino acids, especially isovaline, confirming earlier work. The authors suggest that aqueously-altered planetesimals might have seeded the early Earth with nonracemic amino acids, perhaps explaining why life from microorganisms to people use only L- forms to make proteins. The initial imbalance caused by non-biologic processes in wet asteroids might have been amplified by life on Earth. Alternatively

Pulmonary exposure to carbonaceous nanomaterials and sperm quality

DEFF Research Database (Denmark)

Skovmand, Astrid; Lauvas, Anna Jacobsen; Christensen, Preben

2018-01-01

Background: Semen quality parameters are potentially affected by nanomaterials in several ways: Inhaled nanosized particles are potent inducers of pulmonary inflammation, leading to the release of inflammatory mediators. Small amounts of particles may translocate from the lungs into the lung...... inflammation is a potential modulator of endocrine function. The aim of this study was to investigate the effects of pulmonary exposure to carbonaceous nanomaterials on sperm quality parameters in an experimental mouse model.Methods: Effects on sperm quality after pulmonary inflammation induced by carbonaceous...... nanomaterials were investigated by intratracheally instilling sexually mature male NMRI mice with four different carbonaceous nanomaterials dispersed in nanopure water: graphene oxide (18 mu g/mouse/i.t.), Flammruss 101, Printex 90 and SRM1650b (0.1 mg/mouse/i.t. each) weekly for seven consecutive weeks...

Adsorption of dyes onto carbonaceous materials produced from coffee grounds by microwave treatment.

Science.gov (United States)

Hirata, Mizuho; Kawasaki, Naohito; Nakamura, Takeo; Matsumoto, Kazuoki; Kabayama, Mineaki; Tamura, Takamichi; Tanada, Seiki

2002-10-01

Organic wastes have been burned for reclamation. However, they have to be recycled and reused for industrial sustainable development. Carbonaceous materials were produced from coffee grounds by microwave treatment. There are many phenolic hydroxyl and carboxyl groups on the surface of carbonaceous materials. The base consumption of the carbonaceous materials was larger than that of the commercially activated carbon. The carbonaceous materials produced from coffee grounds were applied to the adsorbates for the removal of basic dyes (methylene blue and gentian violet) in wastewater. This result indicated that the adsorption of dyes depended upon the surface polar groups on the carbonaceous materials. Moreover, the Freundlich constants of isotherms for the adsorption of methylene blue and gentian violet onto the carbonaceous materials produced from coffee grounds were greater than those for adsorption onto activated carbon or ceramic activated carbon. The interaction was greatest between the surface or porosity of the carbonaceous materials and methylene blue and gentian violet. The microwave treatment would be useful for the carbonization of organic wastes to save energy.

Leaching of Antimony (Sb)from Municipal Solid Waste Incineration (MSWI) Residues

Energy Technology Data Exchange (ETDEWEB)

Herrmann, Inga

2004-07-01

The mobility of antimony (Sb) in municipal solid waste incineration (MSWI) residues often exceeds the limit values stipulated by the European Union. As an ash treatment by washing is conceivable, this work investigated the Sb release from Swedish bottom ash and fly ash when mixed with water. The leaching experiments revealed the factors significantly (a = 0.05) affecting Sb release from the ashes. The following factors were investigated: Liquid to solid ratio (L/S), time, pH, carbonation (treatment with CO{sub 2}), ultrasonics and temperature. The data were evaluated using multiple linear regression (MLR). The impact of the factors could be quantified. The maximum Sb release calculated was 13 mg/kg DM for bottom ash and 51 mg/kg DM for fly ash. The derived models explained the observed data well. Nevertheless, the calculated values were subject to a high uncertainty. For bottom ash, a lowering of the Sb total content of approximately 22% could be achieved. If this also involves a sufficient lowering of the Sb mobility to meet EU limit values could not yet be assessed. Chemical equilibrium calculations were performed to explain the empirical results. However, no solid phases controlling Sb release from the ashes could be identified.

Treating carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Corbett, R L; Corbett, E G

1939-03-21

A process is given for the production of aliphatic compounds by heat treatment of carbonaceous material. The latter are impregnated with a dilute solution of a catalyst, such as chromium copper or nickel acetate or nitrate, or ammonium or urea acetate and subjected to destructive distillation in a retort in the presence of a reducing gas and steam, at a pressure not greater than fifteen atmospheres.

Determination of the Energy Potential of the Urban Solid Residuals in Three Municipalities of the County of Luanda, Angola

Directory of Open Access Journals (Sweden)

Dra.C. Yudith González-Diaz

2015-11-01

Full Text Available The biological conversion of the Urban Solid Residuals (USR for energy purposes she comeswinning importance every day, once the urban residuals became considered a source ofalternative energy. To foresee the generation of resulting biogas of the process of biologicaldecomposition of the solid residuals of organic origin in the sanitary fillers is fundamental toestimate the energy and economic balance of facilities of recovery of gas. For the appropriatedetermination of the potential of generation of gases you employment the calculationmethodology presented by the Agency of Environmental Protection of United States. In thiscontext, the objective of this article is to quantify the potential of electric power generationcoming from the gas methane originating of the Urban Solid Residuals of the municipalitiesBelas, Cacuaco and Viana of the County of Luanda in Angola. The available energy power wasdetermined annually of the three municipalities. The instinct demonstrates that the biogas flow e"> arrives at the maximum level and it possesses the maximum available Power in the year 2037,obtaining stops the municipalities Belas, Cacuaco and Viana 3 330· 103, 1 206,13· 103 and 2 809,23· 103m3/ year of profitable methane respectively whose calculated energy potential wasrespectively of 2 316,52, 1 358,88 and 3 165,02 kW. The carried out calculations not allowalone to evaluate the energy potential of the filler, but also to evaluate, in certain way, theenvironmental impact for the mitigation of emissions of gases of effect hothouse.

Solid residues; Os residuos solidos

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

This chapter gives a general overview on the general effects of the solid waste pollution, the principal pollutants emitted by the oil refineries, control actions for the solid waste emissions, the minimization actions, and the effluent treatment.

Direct gas-solid carbonation of serpentinite residues in the absence and presence of water vapor: a feasibility study for carbon dioxide sequestration.

Science.gov (United States)

Veetil, Sanoopkumar Puthiya; Pasquier, Louis-César; Blais, Jean-François; Cecchi, Emmanuelle; Kentish, Sandra; Mercier, Guy

2015-09-01

Mineral carbonation of serpentinite mining residue offers an environmentally secure and permanent storage of carbon dioxide. The strategy of using readily available mining residue for the direct treatment of flue gas could improve the energy demand and economics of CO2 sequestration by avoiding the mineral extraction and separate CO2 capture steps. The present is a laboratory scale study to assess the possibility of CO2 fixation in serpentinite mining residues via direct gas-solid reaction. The degree of carbonation is measured both in the absence and presence of water vapor in a batch reactor. The gas used is a simulated gas mixture reproducing an average cement flue gas CO2 composition of 18 vol.% CO2. The reaction parameters considered are temperature, total gas pressure, time, and concentration of water vapor. In the absence of water vapor, the gas-solid carbonation of serpentinite mining residues is negligible, but the residues removed CO2 from the feed gas possibly due to reversible adsorption. The presence of small amount of water vapor enhances the gas-solid carbonation, but the measured rates are too low for practical application. The maximum CO2 fixation obtained is 0.07 g CO2 when reacting 1 g of residue at 200 °C and 25 barg (pCO2 ≈ 4.7) in a gas mixture containing 18 vol.% CO2 and 10 vol.% water vapor in 1 h. The fixation is likely surface limited and restricted due to poor gas-solid interaction. It was identified that both the relative humidity and carbon dioxide-water vapor ratio have a role in CO2 fixation regardless of the percentage of water vapor.

Life cycle assessment of integrated solid state anaerobic digestion and composting for on-farm organic residues treatment.

Science.gov (United States)

Li, Yangyang; Manandhar, Ashish; Li, Guoxue; Shah, Ajay

2018-03-20

Driven by the gradual changes in the structure of energy consumption and improvements of living standards in China, the volume of on-farm organic solid waste is increasing. If untreated, these unutilized on-farm organic solid wastes can cause environmental problems. This paper presents the results of a life cycle assessment to compare the environmental impacts of different on-farm organic waste (which includes dairy manure, corn stover and tomato residue) treatment strategies, including anaerobic digestion (AD), composting, and AD followed by composting. The input life cycle inventory data are specific to China. The potential environmental impacts of different waste management strategies were assessed based on their acidification potential (AP), eutrophication potential (EP), global warming potential (GWP), ecotoxicity potential (ETP), and resource depletion (RD). The results show that the preferred treatment strategy for dairy manure is the one that integrated corn stover and tomato residue utilization and solid state AD technologies into the system. The GWP of integrated solid state AD and composting was the least, which is -2900 kg CO 2 eq/ t of dairy manure and approximately 14.8 times less than that of current status (i.e., liquid AD of dairy manure). Solid state AD of dairy manure, corn stover and tomato residues is the most favorable option in terms of AP, EP and ETP, which are more than 40% lower than that of the current status (i.e., AP: 3.11 kg SO 2 , EP: -0.94 kg N, and ETP: -881 CTUe (Comparative Toxic Units ecotoxicity)). The results also show that there is a significant potential for AP, EP, ETP, and GWP reduction, if AD is used prior to composting. The scenario analysis for transportation distance showed that locating the AD plant and composting facility on the farm was advantageous in terms of all the life cycle impact categories. Copyright © 2018 Elsevier Ltd. All rights reserved.

Preparation and characterization of a new carbonaceous material for electrochemical systems

Directory of Open Access Journals (Sweden)

ZI JI LIN

2010-02-01

Full Text Available A new carbonaceous material was successfully prepared by the py-rolysis of scrap tire rubber at 600 °C under a nitrogen atmosphere. The physical characteristics of the prepared carbonaceous material were studied by scanning electron microscopy (SEM, X-ray powder diffraction (XRD and X-ray photoelectron spectroscopy (XPS. It was proved that the carbonaceous material had a disordered structure and spherical morphology with an average particle size about 100 nm. The prepared carbonaceous material was also used as electrodes in electrochemical systems to examine its electrochemical performances. It was demonstrated that it delivered a lithium insertion capacity of 658 mA h g-1 during the first cycle with a coulombic efficiency of 68 %. Cyclic voltammograms test results showed that a redox reaction occurred during the cycles. The chemical diffusion coefficient based on the impedance diagram was about 10-10 cm2 s-1. The pyrolytic carbonaceous material derived from scrap tire rubber is therefore considered to be a potential anode material in lithium secondary batteries or capacitors. Furthermore, it is advantageous for environmental protection.

Molybdenum isotopic evidence for the origin of chondrules and a distinct genetic heritage of carbonaceous and non-carbonaceous meteorites

Science.gov (United States)

Budde, Gerrit; Burkhardt, Christoph; Brennecka, Gregory A.; Fischer-Gödde, Mario; Kruijer, Thomas S.; Kleine, Thorsten

2016-11-01

Nucleosynthetic isotope anomalies are powerful tracers to determine the provenance of meteorites and their components, and to identify genetic links between these materials. Here we show that chondrules and matrix separated from the Allende CV3 chondrite have complementary nucleosynthetic Mo isotope anomalies. These anomalies result from the enrichment of a presolar carrier enriched in s-process Mo into the matrix, and the corresponding depletion of this carrier in the chondrules. This carrier most likely is a metal and so the uneven distribution of presolar material probably results from metal-silicate fractionation during chondrule formation. The Mo isotope anomalies correlate with those reported for W isotopes on the same samples in an earlier study, suggesting that the isotope variations for both Mo and W are caused by the heterogeneous distribution of the same carrier. The isotopic complementary of chondrules and matrix indicates that both components are genetically linked and formed together from one common reservoir of solar nebula dust. As such, the isotopic data require that most chondrules formed in the solar nebula and are not a product of protoplanetary impacts. Allende chondrules and matrix together with bulk carbonaceous chondrites and some iron meteorites (groups IID, IIIF, and IVB) show uniform excesses in 92Mo, 95Mo, and 97Mo that result from the addition of supernova material to the solar nebula region in which these carbonaceous meteorites formed. Non-carbonaceous meteorites (enstatite and ordinary chondrites as well as most iron meteorites) do not contain this material, demonstrating that two distinct Mo isotope reservoirs co-existed in the early solar nebula that remained spatially separated for several million years. This separation was most likely achieved through the formation of the gas giants, which cleared the disk between the inner and outer solar system regions parental to the non-carbonaceous and carbonaceous meteorites. The Mo isotope

Bioethanol production: an integrated process of low substrate loading hydrolysis-high sugars liquid fermentation and solid state fermentation of enzymatic hydrolysis residue.

Science.gov (United States)

Chu, Qiulu; Li, Xin; Ma, Bin; Xu, Yong; Ouyang, Jia; Zhu, Junjun; Yu, Shiyuan; Yong, Qiang

2012-11-01

An integrated process of enzymatic hydrolysis and fermentation was investigated for high ethanol production. The combination of enzymatic hydrolysis at low substrate loading, liquid fermentation of high sugars concentration and solid state fermentation of enzymatic hydrolysis residue was beneficial for conversion of steam explosion pretreated corn stover to ethanol. The results suggested that low substrate loading hydrolysis caused a high enzymatic hydrolysis yield; the liquid fermentation of about 200g/L glucose by Saccharomyces cerevisiae provided a high ethanol concentration which could significantly decrease cost of the subsequent ethanol distillation. A solid state fermentation of enzymatic hydrolysis residue was combined, which was available to enhance ethanol production and cellulose-to-ethanol conversion. The results of solid state fermentation demonstrated that the solid state fermentation process accompanied by simultaneous saccharification and fermentation. Copyright © 2012 Elsevier Ltd. All rights reserved.

TESTING OF CARBONACEOUS ADSORBENTS FOR REMOVAL OF POLLUTANTS FROM WATER

Directory of Open Access Journals (Sweden)

RAISA NASTAS

2012-03-01

Full Text Available Testing of carbonaceous adsorbents for removal of pollutants from water. Relevant direction for improving of quality of potable water is application of active carbons at various stages of water treatments. This work includes complex research dealing with testing of a broad spectrum of carbonaceous adsorbents for removal of hydrogen sulfide and nitrite ions from water. The role of the surface functional groups of carbonaceous adsorbents, their acid-basic properties, and the influence of the type of impregnated heteroatom (N, O, or metals (Fe, Cu, Ni, on removal of hydrogen sulfide species and nitrite ions have been researched. The efficiency of the catalyst obtained from peach stones by impregnation with Cu2+ ions of oxidized active carbon was established, being recommended for practical purposes to remove the hydrogen sulfide species from the sulfurous ground waters. Comparative analysis of carbonaceous adsorbents reveals the importance of surface chemistry for oxidation of nitrite ions.

Phytosterols elevation in bamboo shoot residue through laboratorial scale solid-state fermentation using isolated Aspergillus niger CTBU.

Science.gov (United States)

Zheng, X X; Chen, R S; Shen, Y; Yin, Z Y

2014-04-01

Aspergillus niger CTBU isolated from local decayed bamboo shoot residue was employed to solid-state fermentation (SSF) of bamboo shoot residue to elevate the content of phytosterols. Strain acclimatization was carried out under the fermentation condition using bamboo shoot as substrate for fermentation performance improvement. The optimal fermentation temperature and nitrogen level were investigated using acclimatized strain, and SSF was carried out in a 500-ml Erlenmeyer flask feeding 300-mg bamboo shoot residue chips under the optimal condition (33 °C and feeding 4 % urea), and 1,186 mg (100 g)(-1) of total phytosterol was attained after 5-day fermentation, in comparison, only 523 mg (100 g)(-1) of phytosterol was assayed in fresh shoots residue. HPLC analysis of the main composition of total phytosterols displays that the types of phytosterols and composition ratio of main sterols keep steady. This laboratorial scale SSF unit could be scaled up for raw phytosterols production from discarded bamboo shoot residue and could reduce its cost.

Determination of the energy potential of the Urban Solid Residuals in three municipalities of the county of Luanda. Angola

International Nuclear Information System (INIS)

González Diaz, Yudith; Gato Clavell, Tania; Girón Guillot, Rosa L.; Pires Araújo, Luis

2015-01-01

The biological conversion of the Urban Solid Residuals (USR) for energy purposes comes winning importance every day, once the urban residuals became considered a source of alternative energy. To foresee the generation of resulting biogas of the process of biological decomposition of the solid residuals of organic origin in the sanitary fillers is fundamental to estimate the energy and economic balance of facilities of recovery of gas. For the appropriate determination of the potential of generation of gases you employment the calculation methodology presented by the Agency of Environmental Protection of United States. In this context, the objective of this article is to quantify the potential of electric power generation coming from the gas methane originating of the Urban Solid Residuals of the municipalities Belas, Cacuaco and Viana of the County of Luanda in Angola. The available energy power was determined annually of the three municipalities. The instinct demonstrates that the biogas flow arrives at the maximum level and it possesses the maximum available Power in the year 2037, obtaining stops the municipalities Belas, Cacuaco and Viana 3330 · 103, 1206.13 · 103 and 2809.23 · 103m"3/year of profitable methane respectively whose calculated energy potential was respectively of 2316.52, 1358.88 and 3165,02 kW. The carried out calculations not allow alone to evaluate the energy potential of the filler, but also to evaluate, in certain way, the environmental impact for the mitigation of emissions of gases of effect hothouse. (author)

Recycling of air pollution control residues from municipal solid waste incineration into lightweight aggregates.

Science.gov (United States)

Quina, Margarida J; Bordado, João M; Quinta-Ferreira, Rosa M

2014-02-01

This work focuses on the assessment of technological properties and on the leaching behavior of lightweight aggregates (LWA) produced by incorporating different quantities of air pollution control (APC) residues from municipal solid waste (MSW) incineration. Currently this hazardous waste has been mostly landfilled after stabilization/solidification. The LWA were produced by pelletizing natural clay, APC residues as-received from incineration plant, or after a washing treatment, a small amount of oil and water. The pellets were fired in a laboratory chamber furnace over calcium carbonate. The main technological properties of the LWA were evaluated, mainly concerning morphology, bulk and particle densities, compressive strength, bloating index, water adsorption and porosity. Given that APC residues do not own expansive (bloating) properties, the incorporation into LWA is only possible in moderate quantities, such as 3% as received or 5% after pre-washing treatment. The leaching behavior of heavy metals from sintered LWA using water or acid solutions was investigated, and despite the low acid neutralization capacity of the synthetic aggregates, the released quantities were low over a wide pH range. In conclusion, after a washing pre-treatment and if the percentage of incorporation is low, these residues may be incorporated into LWA. However, the recycling of APC residues from MSW incineration into LWA does not revealed any technical advantage. Copyright © 2013 Elsevier Ltd. All rights reserved.

Modelling of different enzyme productions by solid-state fermentation on several agro-industrial residues.

Science.gov (United States)

Diaz, Ana Belen; Blandino, Ana; Webb, Colin; Caro, Ildefonso

2016-11-01

A simple kinetic model, with only three fitting parameters, for several enzyme productions in Petri dishes by solid-state fermentation is proposed in this paper, which may be a valuable tool for simulation of this type of processes. Basically, the model is able to predict temporal fungal enzyme production by solid-state fermentation on complex substrates, maximum enzyme activity expected and time at which these maxima are reached. In this work, several fermentations in solid state were performed in Petri dishes, using four filamentous fungi grown on different agro-industrial residues, measuring xylanase, exo-polygalacturonase, cellulose and laccase activities over time. Regression coefficients after fitting experimental data to the proposed model turned out to be quite high in all cases. In fact, these results are very interesting considering, on the one hand, the simplicity of the model and, on the other hand, that enzyme activities correspond to different enzymes, produced by different fungi on different substrates.

Raman characterization of carbonaceous matter in CONCORDIA Antarctic micrometeorites

Science.gov (United States)

Dobricǎ, E.; Engrand, C.; Quirico, E.; Montagnac, G.; Duprat, J.

2011-09-01

Abstract- We report a multi-wavelength Raman spectroscopy study of carbonaceous matter in 38 Antarctic micrometeorites (AMMs) from the 2006 CONCORDIA collection. The particles were selected as a function of their degree of thermal alteration developed during the deceleration in the atmosphere. These samples range from unmelted (fine-grained—Fg; ultracarbonaceous—UCAMMs) to partially melted AMMs (scorias—Sc) and completely melted particles (cosmic spherules—CS). More than half of the analyzed AMMs contain a substantial amount of polyaromatic carbonaceous matter with a high degree of disorder. The proportion of particles where carbon is not detected increase from the Fg to the Fg-Sc and to the Sc-AMMs, and no carbon is detected in CS. In addition, the spectral characteristics of the G and D bands of the carbonaceous matter in Sc-AMMs plot apart from the trend formed by the data from Fg-AMMs and UCAMMs. These results suggest that oxidation processes occurred during the deceleration of the particles in the atmosphere. In Fg-AMMs and UCAMMs, the spectral characteristics of the G and D bands reveal the high degree of disorder of the carbonaceous matter, precluding a long duration thermal metamorphism on the parent body and suggesting that AMMs have a connection with C1-C2 chondrites. The Raman parameters of the deuterium-rich carbonaceous matter of UCAMMs do not differ from that of Fg-AMMs. Using a 244 nm excitation, we detected the cyanide (-CN) functional group for the first time in a UCAMM, reinforcing the likely cometary origin of this type of micrometeorites.

Baseline toxicity of a chlorobenzene mixture and total body residues measured and estimated with solid-phase microextraction

NARCIS (Netherlands)

Leslie, H.A.; Hermens, J.L.; Kraak, M.H.S.

2004-01-01

Body residues of compounds with a narcotic mode of action that exceed critical levels result in baseline toxicity in organisms. Previous studies have shown that internal concentrations in organisms also can be estimated by way of passive sampling. In this experiment, solid-phase microextraction

Polycyclic aromatic hydrocarbons and volatile organic compounds in biochar and biochar-amended soil: A review

Science.gov (United States)

Residual pollutants including polycyclic aromatic hydrocarbons (PAHs), volatile organic compounds (VOCs), and carbon(aceous) nanoparticles are inevitably generated during the pyrolysis of waste biomass, and remain on the solid co-product called biochar. Such pollutants could have adverse effects on ...

Improved process for heating finely divided carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

1956-08-01

A process for heating finely divided carbonaceous particles by burning a proportion of the carbon consists of passing the carbonaceous material at a temperature above 800/sup 0/F into an upwardly disposed, slender, combustion zone, suspending the particles in an upwardly-moving gas containing free oxygen so that the suspension has a density from 0.1 to 5.0 lb/cu. ft., passing the suspension upwardly through the combustion zone at a velocity of from 5 to 100 ft./sec., and injecting at least one stream of a second gas containing free oxygen at a point in the combustion zone such that at least 50% of the oxygen in the first gas has been consumed by the time the suspension reaches this point. The total quantity of oxygen is chosen so that the finely divided carbonaceous material is heated to a temperature of not less than 1,050/sup 0/F.

Decolorization of textile industry wastewater in solid state fermentation with Peach-Palm (Bactris gasipaes residue

Directory of Open Access Journals (Sweden)

J. A. Chicatto

2018-02-01

Full Text Available Abstract In this work we have assessed the decolorization of textile effluents throughout their treatment in a solid-state fermentation (SSF system. SSF assays were conducted with peach-palm (Bactris gasipaes residue using the white rot fungus Ganoderma lucidum EF 31. The influence of the dye concentration and of the amounts of peach-palm residue and liquid phase on both the discoloration efficiency and enzyme production was studied. According to our results, independently of experimental conditions employed, laccase was the main ligninolytic enzyme produced by G. lucidum. The highest laccase activity was obtained at very low effluent concentrations, suggesting the existence of an inhibitory effect of higher concentrations on fungal metabolism. The highest percentage of color removal was reached when 10 grams of peach palm residue was moistened with 60 mL of the final effluent. In control tests carried out with the synthetic dye Remazol Brilliant Blue R (RBBR decolorization efficiencies about 20% higher than that achieved with the industrial effluent were achieved. The adsorption of RBBR on peach-palm residue was also investigated. Equilibrium tests showed that the adsorption of this dye followed both Langmuir and Freundlich isotherms. Hence, our experimental results indicate that peach-palm residue is suitable substrate for both laccase production and color removal in industrial effluents.

Decolorization of textile industry wastewater in solid state fermentation with Peach-Palm (Bactris gasipaes) residue.

Science.gov (United States)

Chicatto, J A; Rainert, K T; Gonçalves, M J; Helm, C V; Altmajer-Vaz, D; Tavares, L B B

2018-02-15

In this work we have assessed the decolorization of textile effluents throughout their treatment in a solid-state fermentation (SSF) system. SSF assays were conducted with peach-palm (Bactris gasipaes) residue using the white rot fungus Ganoderma lucidum EF 31. The influence of the dye concentration and of the amounts of peach-palm residue and liquid phase on both the discoloration efficiency and enzyme production was studied. According to our results, independently of experimental conditions employed, laccase was the main ligninolytic enzyme produced by G. lucidum. The highest laccase activity was obtained at very low effluent concentrations, suggesting the existence of an inhibitory effect of higher concentrations on fungal metabolism. The highest percentage of color removal was reached when 10 grams of peach palm residue was moistened with 60 mL of the final effluent. In control tests carried out with the synthetic dye Remazol Brilliant Blue R (RBBR) decolorization efficiencies about 20% higher than that achieved with the industrial effluent were achieved. The adsorption of RBBR on peach-palm residue was also investigated. Equilibrium tests showed that the adsorption of this dye followed both Langmuir and Freundlich isotherms. Hence, our experimental results indicate that peach-palm residue is suitable substrate for both laccase production and color removal in industrial effluents.

On the Q-phase of carbonaceous chondrites

International Nuclear Information System (INIS)

Vis, R.D.; Heymann, D.

1999-01-01

One of the unresolved puzzles of meteoritics is the nature of the carrier of the so-called heavy planetary gases. Apparently, these gases reside mainly in a minor fraction, which has been dubbed Q by Lewis et al. [R.S. Lewis, B. Srinivasan, E. Anders, Science 190 (1975) 1251] in analogy of the naming by Papanastasiou et al. [D.A. Papanastassiou, G.J. Wasserburg, Earth Planet. Sci. Lett. 11 (1971) 37] of a minor glassy phase in lunar rocks highly enriched in trace elements such as Pb and U. Q stands for the archaic term quintessence, the fifth or last and highest substance in ancient and medieval philosophy above fire, air, water and earth. In this contribution, an attempt is made to provide evidence that Q is carbonaceous, with carbon in the form of closed structures such as carbon nanotubes which serve as micro bottles for the heavy noble gases. To this end, Q was characterised with micro-PIXE and NRA, whereas HREM was used to search for nanotubes. Q itself was obtained as residue after chemical destruction of samples of Allende, Leoville and Vigarano

The Role of Fe,Ni Metal and Fe,Ni Sulfide Nanoparticles in Catalytic Organic Synthesis in the Early Solar System: Evidence From Carbonaceous Chondrites.

Science.gov (United States)

Brearley, A. J.

2008-12-01

Numerous studies have shown that carbonaceous chondrites contain a wide variety of both soluble and insoluble organic compounds. These compounds formed in a variety of different astrophysical environments including the interstellar medium, the solar nebula and on asteroidal parent bodies. The solid or insoluble organic material (IOM) in carbonaceous chondrites is likely the complex end product of synthesis and processing in all of these environments. Although the bulk chemistry and structure of IOM in carbonaceous chondrites is well understood, important questions remain as to the exact spatial occurrence and distribution of organic material within carbonaceous chondrites. Such information may provide important insights into the possible mechanisms of formation of organic material at the grain scale. We have examined the matrices of three CM carbonaceous chondrites, Y791198, Murchison and ALH81002 using a range of different TEM techniques. Mineralogically, the matrices of these meteorites consist of phyllosilicates and/or amorphous materials associated with sulfides, oxides and carbides. Using energy filtered TEM several distinct occurrences of organic material have been identified, notably associations with nanoparticles of sulfide and carbide. Sulfides have grain sizes that are commonly <100 nm with thin layers of poorly graphitized C (<1 nm) on their surfaces. This carbonaceous layer often contains nitrogen suggesting that it is organic in character. In addition, nanoparticles of Fe,Ni carbides that occur either singly or in clusters are often embedded in carbonaceous material that is also N-bearing. These carbides have experienced partial oxidation to magnetite around their rims. The ubiquitous spatial association between sulfide and carbide nanoparticles and carbonaceous material indicates a genetic relation between these phases. This association can be most readily explained by Fischer-Tropsch-type (FTT) catalysis reactions involving catalytic hydrogenation

Isotopic measurements (C,N,O) of detonation soot produced from labeled and unlabeled Composition B-3 indicate source of solid carbon residues

Science.gov (United States)

Podlesak, David; Manner, Virginia; Amato, Ronald; Dattelbaum, Dana; Gusavsen, Richard; Huber, Rachel

2017-06-01

Detonation of HE is an exothermic process whereby metastable complex molecules are converted to simple stable molecules such as H2 O, N2, CO, CO2, and solid carbon. The solid carbon contains various allotropes such as detonation nanodiamonds, graphite, and amorphous carbon. It is well known that certain HE formulations such as Composition B (60% RDX, 40% TNT) produce greater amounts of solid carbon than other more oxygen-balanced formulations. To develop a greater understanding of how formulation and environment influence solid carbon formation, we synthesized TNT and RDX with 13 C and 15 N at levels slightly above natural abundance levels. Synthesized RDX and TNT were mixed at a ratio of 60:40 to form Composition B and solid carbon residues were collected from detonations of isotopically-labeled as well as un-labelled Composition B. The raw HE and detonation residues were analyzed isotopically for C, N, O isotopic compositions. We will discuss differences between treatments groups as a function of formulation and environment. LA-UR - 17-21266.

Environmental performance of the Kvaerner BFB boilers for MSW combustion -- Analysis of gaseous emissions and solid residues

International Nuclear Information System (INIS)

Lundberg, M.; Hagman, U.; Andersson, B.A.; Olofsson, J.

1997-01-01

Kvaerner Pulping AB (formerly Kvaerner EnviroPower AB) has, due to the stringent demands on emissions performance, developed a state-of-the-art bubbling fluidized bed boiler (BFB) designed for waste fuel firing with very low emissions to the air. A complete evaluation of the environmental performance of the Kvaerner BFB technique for MSW combustion is now possible thanks to a thorough characterization study of the solid residues from the Lidkoeping plant. This paper gives an overall mapping of the emissions performance. Data from the operating plants on solid residue characteristics and leachability, heavy metal and dioxin emissions, nitrogen oxides, carbon monoxide, acid gases, and other emissions to air are presented. Comparisons are made with legislative limits and data from the mass burning technique. It is concluded that the emissions are low compared both with data from traditional mass burn incinerators and with legislative limits in the USA and Europe. Furthermore, the bottom and cyclone ash characteristics are shown not to cause any particular problem from an environmental point of view, and that the leachability is well below the existing legislative limits in Europe and the USA. The results show that fluidized bed combustion of municipal solid waste is a very competitive alternative to the traditional mass burning technique in every respect

Carbonaceous material treatment

Energy Technology Data Exchange (ETDEWEB)

Trevor, S R

1939-05-04

To separate and collect for use the component parts of carbonaceous materials, they are fed to superimposed connected vertical or substantially vertical chambers, located over a furnace, the flue gases from which pass to space or spaces of a casing surrounding the superimposed chambers. Pipes are provided so that part or whole of the gases may be passed through the chambers. Take-off pipes are connected to expansion chambers, through which the gases pass to condenser coils and separating tanks.

Simultaneous Determination of TetracyclinesResidues in Bovine Milk Samples by Solid Phase Extraction and HPLC-FL Method

Directory of Open Access Journals (Sweden)

Mehra Mesgari Abbasi

2011-06-01

Full Text Available Introduction:Tetracyclines (TCs are widely used in animal husbandry and their residues in milk may resultinharmful effects on human. The aim of this study was to investigate the presence of TCs residues in various bovine milk samples from local markets of Ardabil, Iran. Methods:One hundred and fourteen pasteurized, sterilized and raw milk samples were collected from markets of Ardabil. Tetracycline, Oxytetracycline and Chlortetracycline (TCs residues extraction carried out by Solid Phase Extraction method. Determination of TCs residues were performed by high performance liquid chromatography (HPLC method using Fluorescence detector.Results: The mean of total TCs residues in all samples (114 samples was 97.6 ±16.9ng/g and that of pasteurized, sterilized and raw milk samples were 87.1 ± 17.7, 112.0 ± 57.3 and 154.0 ± 66.3ng/g respectively. Twenty five point four percent of the all samples, and24.4%, 30% and 28.6% of the pasteurized, sterilized and raw milk samples, respectively had higher TCs residues than the recommended maximum levels (100ng/g. Conclusion:This study indicates the presence of tetracycline residues more than allowed amount. Regulatory authorities should ensure proper withdrawal period before milking the animals and definite supervisions are necessary on application of these drugs.

Strong and Optically Transparent Films Prepared Using Cellulosic Solid Residue Recovered from Cellulose Nanocrystals Production Waste Stream

Science.gov (United States)

Qianqian Wang; J.Y. Zhu; John M. Considine

2013-01-01

We used a new cellulosic material, cellulosic solid residue (CSR), to produce cellulose nanofibrils (CNF) for potential high value applications. Cellulose nanofibrils (CNF) were produced from CSR recovered from the hydrolysates (waste stream) of acid hydrolysis of a bleached Eucalyptus kraft pulp (BEP) to produce nanocrystals (CNC). Acid hydrolysis greatly facilitated...

Characterization of Hospital Residuals

International Nuclear Information System (INIS)

Blanco Meza, A.; Bonilla Jimenez, S.

1997-01-01

The main objective of this investigation is the characterization of the solid residuals. A description of the handling of the liquid and gassy waste generated in hospitals is also given, identifying the source where they originate. To achieve the proposed objective the work was divided in three stages: The first one was the planning and the coordination with each hospital center, in this way, to determine the schedule of gathering of the waste can be possible. In the second stage a fieldwork was made; it consisted in gathering the quantitative and qualitative information of the general state of the handling of residuals. In the third and last stage, the information previously obtained was organized to express the results as the production rate per day by bed, generation of solid residuals for sampled services, type of solid residuals and density of the same ones. With the obtained results, approaches are settled down to either determine design parameters for final disposition whether for incineration, trituration, sanitary filler or recycling of some materials, and storage politics of the solid residuals that allow to determine the gathering frequency. The study concludes that it is necessary to improve the conditions of the residuals handling in some aspects, to provide the cleaning personnel of the equipment for gathering disposition and of security, minimum to carry out this work efficiently, and to maintain a control of all the dangerous waste, like sharp or polluted materials. In this way, an appreciable reduction is guaranteed in the impact on the atmosphere. (Author) [es

Alternatives for the treatment of the organic fraction of the urban solid residuals

International Nuclear Information System (INIS)

Benitez Fonseca, Mabelin; Fernandez Mena, Dalia; Abalos Rodriguez, Arelis; Rodriguez Perez, Suyen

2011-01-01

The decomposition of municipal solid waste outdoors, or in some cases burning under the same conditions, is action now and final disposition of these wastes without measuring their consequences. In the student's residence 'Antonio Maceo' Orient University is hosting up to 2250 students belonging to a total of 22 university, generating at full capacity, 3375 kg / day of MSW. This research aims to analyze the solid waste generated in the student's residence, where improperly evaluated the final disposition thereof. It was found that discharges are not separated at the source observed at the landfill, food waste, sweeping waste, paper and cardboard, plastics, glass, metal, textile waste, wood, etc. Samplings were carried out directly in 12 rooms of the residence for a total of 48 people, along with students, as part of the educational activities implemented within this work. The average weight of degradable waste generated was 2.5 kg / day during the sampling, revealing the presence of traces of cooked food (cereals, legumes, carbohydrates), fruit and vegetable remains, remains of shells of different origins ( meats, eggs), remnants of tea, etc. The average content of total solids in the waste sampled was 36.3 ± 5.4% and volatile solids content on dry weight was 81.3 ± 2.5% to an average density of 0.68 g / cm3. This residue is characterized to be treated in an anaerobic batch reactor where it is recirculated leachate and studied the competing microorganisms in the anaerobic degradation of organic fraction of municipal solid waste. (author)

Baking process of thin plate carbonaceous compact

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Yoshio; Shimada, Toyokazu

1987-06-27

As a production process of a thin plate carbonaceous compact for separator of phosphoric acid fuel cell, there is a process to knead carbonaceous powder and thermosetting resin solution, to form and harden the kneaded material and then to bake, carbonize and graphitize it. However in this baking and carbonization treatment, many thin plate compacts are set in a compiled manner within a heating furnace and receive a heat treatment from their circumference. Since the above compacts to be heated tend generally to be heated from their peripheries, their baked conditions are not homogeneous easily causing the formation of cracks, etc.. As a process to heat and bake homogeneously by removing the above problematical points, this invention offers a process to set in a heating furnace a laminate consisting of the lamination of thin plate carbonaceous compacts and the heat resistant soaking plates which hold the upper and lower ends of the above lamination, to fill the upper and under peripheries of the laminate above with high heat conductive packing material and its side periphery with low heat conductive packing material respectively and to heat and sinter it. In addition, the invention specifies the high and low heat conductive packing materials respectively. (1 fig, 2 tabs)

Nebula Scale Mixing Between Non-Carbonaceous and Carbonaceous Chondrite Reservoirs: Testing the Grand Tack Model with Almahata Sitta Stones

Science.gov (United States)

Yin, Q.-Z.; Sanborn, M. E.; Goodrich, C. A.; Zolensky, M.; Fioretti, A. M.; Shaddad, M.; Kohl, I. E.; Young, E. D.

2018-01-01

There is an increasing number of Cr-O-Ti isotope studies that show that solar system materials are divided into two main populations, one carbonaceous chondrite (CC)-like and the other is non-carbonaceous (NCC)-like, with minimal mixing between them attributed to a gap opened in the propoplanetary disk due to Jupiter's formation. The Grand Tack model suggests that there should be a particular time in the disk history when this gap is breached and ensuring a subsequent large-scale mixing between S- and C-type asteroids (inner solar system and outer solar system materials), an idea supported by our recent work on chondrule (Delta)17O-(epsilon)54Cr isotope systematics.

Immobilization of acid digestion residue

International Nuclear Information System (INIS)

Greenhalgh, W.O.; Allen, C.R.

1983-01-01

Acid digestion treatment of nuclear waste is similar to incineration processes and results in the bulk of the waste being reduced in volume and weight to some residual solids termed residue. The residue is composed of various dispersible solid materials and typically contains the resultant radioactivity from the waste. This report describes the immobilization of the residue in portland cement, borosilicate glass, and some other waste forms. Diagrams showing the cement and glass virtification parameters are included in the report as well as process steps and candidate waste product forms. Cement immobilization is simplest and probably least expensive; glass vitrification exhibits the best overall volume reduction ratio

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

Energy Technology Data Exchange (ETDEWEB)

Kivaisi, A K [Univ. of Dar es Salaam, Botany Dept., Applied Microbiology Unit (Tanzania, United Republic of)

1998-12-31

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country`s big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m{sup 3} CH{sub 4}/ton VS of sisal pulp; 400 m{sup 3} CH{sub 4}/ton VS of sisal production wastewater; 400 m{sup 3} CH{sub 4}/ton VS of Robusta coffee solid waste, 350 m{sup 3} CH{sub 4}/ton VS of sugar processing wastewater; 250 m{sup 3} CH{sub 4}/ton VS of sugar filter mat, 450 m{sup 3} CH{sub 4}/ton VS maize bran and 300 m{sup 3} CH{sub 4}/ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO{sub 2} emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

Energy Technology Data Exchange (ETDEWEB)

Kivaisi, A.K. [Univ. of Dar es Salaam, Botany Dept., Applied Microbiology Unit (Tanzania, United Republic of)

1997-12-31

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country`s big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m{sup 3} CH{sub 4}/ton VS of sisal pulp; 400 m{sup 3} CH{sub 4}/ton VS of sisal production wastewater; 400 m{sup 3} CH{sub 4}/ton VS of Robusta coffee solid waste, 350 m{sup 3} CH{sub 4}/ton VS of sugar processing wastewater; 250 m{sup 3} CH{sub 4}/ton VS of sugar filter mat, 450 m{sup 3} CH{sub 4}/ton VS maize bran and 300 m{sup 3} CH{sub 4}/ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO{sub 2} emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

International Nuclear Information System (INIS)

Kivaisi, A.K.

1997-01-01

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country's big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m 3 CH 4 /ton VS of sisal pulp; 400 m 3 CH 4 /ton VS of sisal production wastewater; 400 m 3 CH 4 /ton VS of Robusta coffee solid waste, 350 m 3 CH 4 /ton VS of sugar processing wastewater; 250 m 3 CH 4 /ton VS of sugar filter mat, 450 m 3 CH 4 /ton VS maize bran and 300 m 3 CH 4 /ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO 2 emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled anaerobic systems it is possible to reduce the methane emission by

Fast thermal annealing of implantation defects in silicon. Solid phase epitaxy and residual imperfection recovery

International Nuclear Information System (INIS)

Adekoya, O.A.

1987-06-01

Basic processes ruling the crystal reconstitution in solid phase during fast thermal annealing are studied; the role of electronic and thermodynamic effects at the interface is precised, following the implantations of a donor element (p + ), an acceptor element (B + ) and an intrinsic element (Ge + ). Then, after recrystallization, the electric role of residual point defects is shown together with the possibility of total recovery and an important electric activation of the doping [fr

Distilling carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Trumble, M J

1925-06-29

Carbonaceous materials such as coal, oil shale, peat, or wood are destructively distilled while being subjected to the action of superheated steam and hydrogen, the latter being provided by dissociating a part of the superheated steam. The materials are charged into a retort heated by a burner and superheated steam and hydrogen are passed in by a pipe and nozzles. The distillates enter a dust extractor through openings and escape through openings shielded by cones into an outlet pipe leading to condensers. The dust which settles in the bottom of the apparatus is periodically removed.

Fuel cells for electricity generation from carbonaceous fuels

Energy Technology Data Exchange (ETDEWEB)

Ledjeff-Hey, K; Formanski, V; Roes, J [Gerhard-Mercator- Universitaet - Gesamthochschule Duisburg, Fachbereich Maschinenbau/Fachgebiet Energietechnik, Duisburg (Germany); Heinzel, A [Fraunhofer Inst. for Solar Energy Systems (ISE), Freiburg (Germany)

1998-09-01

Fuel cells, which are electrochemical systems converting chemical energy directly into electrical energy with water and heat as by-products, are of interest as a means of generating electricity which is environmentally friendly, clean and highly efficient. They are classified according to the electrolyte used. The main types of cell in order of operating temperature are described. These are: alkaline fuel cells, the polymer electrolyte membrane fuel cell (PEMFC); the phosphoric acid fuel cell (PAFC); the molten carbonate fuel cell (MCFC); the solid oxide fuel cell (SOFC). Applications depend on the type of cell and may range from power generation on a large scale to mobile application in cars or portable systems. One of the most promising options is the PEM-fuel cell stack where there has been significant improvement in power density in recent years. The production from carbonaceous fuels and purification of the cell fuel, hydrogen, is considered. Of the purification methods available, hydrogen separation by means of palladium alloy membranes seems particular effective in reducing CO concentrations to the low levels required for PEM cells. (UK)

Effects of residues from municipal solid waste landfill on corn yield and heavy metal content

International Nuclear Information System (INIS)

Prabpai, S.; Charerntanyarak, L.; Siri, B.; Moore, M.R.; Noller, Barry N.

2009-01-01

The effects of residues from municipal solid waste landfill, Khon Kaen Municipality, Thailand, on corn (Zea mays L.) yield and heavy metal content were studied. Field experiments with randomized complete block design with five treatments (0, 20, 40, 60 and 80% v/v of residues and soil) and four replications were carried out. Corn yield and heavy metal contents in corn grain were analyzed. Corn yield increased by 50, 72, 85 and 71% at 20, 40, 60 and 80% treatments as compared to the control, respectively. All heavy metals content, except cadmium, nickel and zinc, in corn grain were not significantly different from the control. Arsenic, cadmium and zinc in corn grain were strongly positively correlated with concentrations in soil. The heavy metal content in corn grain was within regulated limits for human consumption.

Structure and isotopic ratios of aliphatic side chains in the insoluble organic matter of the Murchison carbonaceous chondrite

Science.gov (United States)

Huang, Yongsong; Alexandre, Marcelo R.; Wang, Yi

2007-07-01

We report in this paper the first molecular and isotopic characterization of individual aliphatic side chains from the insoluble organic matter (IOM) in the Murchison carbonaceous chondrite using a novel combined approach of RuO 4 oxidation and solid phase microextraction (SPME). The aliphatic side chains in the IOM of Murchison were first released by oxidizing aromatic structures using RuO 4. Because the IOM of carbonaceous chondrites contains predominantly short (C 1 to C 9) aliphatic substitutions, the resulting low molecular weight monocarboxylic acids (MCAs) are highly volatile and water-soluble. The conventional aqueous extraction and derivatization procedures following RuO 4 oxidation are unable to recover MCAs for subsequent analyses. We overcame this problem by employing SPME to directly capture the MCAs from the aqueous solution. We selected a SPME fiber with greater affinity for longer chain monoacids to compensate for the exponential decline of monoacid concentrations with increasing carbon numbers in meteorite IOM, allowing more accurate identification and quantification for the less abundant monoacids. We also determined the carbon and hydrogen isotopic ratios of individual MCAs derived from Murchinson IOM. Our results reveal significant similarity in both molecular structures and hydrogen isotopic ratios between the IOM aliphatic side chains and water-soluble MCAs in Murchison, suggesting that these compounds had common precursors. Our combined new approach of RuO 4 oxidation-SPME provides a new way to probe the molecular and isotopic characteristics of aliphatic side chains in carbonaceous chondrites.

Characterization of carbonaceous aerosol emissions from selected combustion sources

International Nuclear Information System (INIS)

Martinez, J.P.G.; Espino, M.P.M.; Pabroa, P.C.B.; Bautista, A.T. VII

2015-01-01

Carbonaceous Particulates are carbon-containing solid or liquid matter which form a significant portion of the fine particulate mass (PM2.5) and these have known profound adverse effects on health, climate and visibility. This study aims to characterize carbonaceous aerosol emissions from different combustion sources to establish fingerprints for these for use in the refinement of improvement of the resolution of sources apportionment studies being done by the Philippine Nuclear Research Institute (PNRI), i.e. to resolve vehicular emission sources. Fine air particulate sample were collected in pre-baked Quartz filters using an improvised collection set-up with a Gent sampler. Concentrations of organic and elemental carbon (OC and EC, respectively) in PM2.5 were measured for the different combustion sources—vehicular emissions, tire pyrolysis, and biomass burning, using a thermal-optical method of analysis following the IMPROVE_A protocol. Measured OC ad EC concentrations are shown as percentages with respect to the total carbon (TC) and are illustrated in a 100% stacked chart. Predominance of the EC2 fraction is exhibited in both the diesel fuelled vehicle and tire pyrolysis emissions with EC2/OC2 ratio distinguishing one from the other, EC2/OC2 is 1.63 and 8.41, respectively. Predominance of either OC2 or OC3 fraction is shown in the unleaded gasoline and LPG Fuelled vehicles and in biomass burning with the OC2/OC3 ratio distinguishing one from the others. OC2/OC3 ratios are 1.33 for unleaded gasoline fuelled vehicle, 1.89 for LPG-fuelled vehicle, 0.55 for biomass burning (leaves) and 0.82 biomass burning (wood). The study has shown probable use of the EC2/OC2 and OC2/OC3 ratios to distinguish fingerprints for combustion sources covered in this study. (author)

Conditioning of high activity solid waste: fuel claddings and dissolution residues

International Nuclear Information System (INIS)

Anon.

1982-01-01

This chapter reports on experimental studies of embedding into matrix material, the melting and conversion of zircaloy, and waste properties and characterization. Methods are developed for embedding the waste scrap into a solid and resistant matrix material in order to confine the radioactivity and to prevent it from dispersion. The matrix materials investigated are lead alloys, ceramics and compacted graphite or aluminium powder. The treatment of fuel hulls by melting or chemical conversion is described. Cemented hulls are characterized and the pyrophoricity of zircaloy fines is investigated. Topics considered include the embedding of hulls into graphite and aluminium, the embedding of hulls and dissolution residues into alumino-ceramics, the solidification of alpha-bearing wastes into a ceramic matrix, and the conditioning of cladding waste by eutectoidic melting and by embedding in glass

The Thermal Properties of CM Carbonaceous Chondrites

Science.gov (United States)

Britt, D. T.; Opeil, C.

2017-12-01

The physical properties of asteroid exploration targets are fundamental parameters for developing models, planning observations, mission operations, reducing operational risk, and interpreting mission results. Until we have returned samples, meteorites represent our "ground truth" for the geological material we expect to interact with, sample, and interpret on the surfaces of asteroids. The physical properties of the volatile-rich carbonaceous chondrites (CI, C2, CM, and CR groups) are of particular interest because of their high resource potential. We have measured the thermal conductivity, heat capacity and thermal expansion of five CM carbonaceous chondrites (Murchison, Murray, Cold Bokkeveld, NWA 7309, Jbilet Winselwan) at low temperatures (5-300 K) to mimic the conditions in the asteroid belt. The mineralogy of these meteorites are dominated by abundant hydrous phyllosilicates, but also contain anhydrous minerals such as olivine and pyroxene found in chondrules. The thermal expansion measurements for all these CMs indicate a substantial increase in meteorite volume as temperature decreases from 230 - 210 K followed by linear contraction below 210 K. Such transitions were unexpected and are not typical for anhydrous carbonaceous chondrites or ordinary chondrites. Our thermal diffusivity results compare well with previous estimates for similar meteorites, where conductivity was derived from diffusivity measurements and modeled heat capacities; our new values are of a higher precision and cover a wider range of temperatures.

On thermodynamics of methane+carbonaceous materials adsorption

KAUST Repository

Rahman, Kazi Afzalur; Chakraborty, Anutosh; Saha, Bidyut Baran; Ng, Kim Choon

2012-01-01

This study presents the theoretical frameworks for the thermodynamic quantities namely the heat of adsorption, specific heat capacity, entropy, and enthalpy for the adsorption of methane onto various carbonaceous materials. The proposed theoretical

Lignocellulose fermentation and residual solids characterization for senescent switchgrass fermentation by Clostridium thermocellum in the presence and absence of continuous in situ ball-milling

Energy Technology Data Exchange (ETDEWEB)

Balch, Michael L.; Holwerda, Evert K.; Davis, Mark F.; Sykes, Robert W.; Happs, Renee M.; Kumar, Rajeev; Wyman, Charles E.; Lynd, Lee R.

2017-04-12

Milling during lignocellulosic fermentation, henceforth referred to as cotreatment, is investigated as an alternative to thermochemical pretreatment as a means of enhancing biological solubilization of lignocellulose. We investigate the impact of milling on soluble substrate fermentation by Clostridium thermocellum with comparison to yeast, document solubilization for fermentation of senescent switchgrass with and without ball milling, and characterize residual solids. Soluble substrate fermentation by C. thermocellum proceeded readily in the presence of continuous ball milling but was completely arrested for yeast. Total fractional carbohydrate solubilization achieved after fermentation of senescent switchgrass by C. thermocellum for 5 days was 0.45 without cotreatment or pretreatment, 0.81 with hydrothermal pretreatment (200 degrees C, 15 minutes, severity 4.2), and 0.88 with cotreatment. Acetate and ethanol were the main fermentation products, and were produced at similar ratios with and without cotreatment. Analysis of solid residues was undertaken using molecular beam mass spectrometry (PyMBMS) and solid-state nuclear magnetic resonance spectroscopy (NMR) in order to provide insight into changes in plant cell walls during processing via various modes. The structure of lignin present in residual solids remaining after fermentation with cotreatment appeared to change little, with substantially greater changes observed for hydrothermal pretreatment - particularly with respect to formation of C-C bonds. The observation of high solubilization with little apparent modification of the residue is consistent with cotreatment enhancing solubilization primarily by increasing the access of saccharolytic enzymes to the feedstock, and C. thermocellum being able to attack all the major linkages in cellulosic biomass provided that these linkages are accessible.

Comets, Carbonaceous Meteorites, and the Origin of the Biosphere

Science.gov (United States)

Hoover, Richard B.

2007-01-01

Evidence for indigenous microfossils in carbonaceous meteorites suggests that the paradigm of the endogenous origin of life on Earth should be reconsidered. It is now widely accepted that comets and carbonaceous meteorites played an important role in the delivery of water, organics and life critical biogenic elements to the early Earth and facilitated the origin and evolution of the Earth's Biosphere. However; the detection of embedded microfossils and mats in carbonaceous meteorites implies that comets and meteorites may have played a direct role in the delivery of intact microorganisms and that the Biosphere may extend far into the Cosmos. Recent space observations have found the nuclei of comets to have very low albedos (approx.0.03) and. these jet-black surfaces become very hot (T approx. 400 K) near perihelion. This paper reviews recent observational data-on comets and suggests that liquid water pools could exist in cavities and fissures between the internal ices and rocks and the exterior carbonaceous crust. The presence of light and liquid water near the surface of the nucleus enhances the possibility that comets could harbor prokaryotic extremophiles (e.g., cyanobacteria) capable of growth over a wide range of temperatures. The hypothesis that comets are the parent bodies of the CI1 and the CM2 carbonaceous meteorites is advanced. Electron microscopy images will be presented showing forms interpreted as indigenous-microfossils embedded' in freshly. fractured interior surfaces of the Orgueil (CI1) and Murchison (CM2) meteorites. These forms are consistent in size and morphologies with known morphotypes of all five orders of Cyanobacteriaceae: Energy Dispersive X-ray Spectroscopy (EDS) elemental data shows that the meteoritic forms have anomalous C/O; C/N; and C/S as compared with modern extremophiles and cyanobacteria. These images and spectral data indicate that the clearly biogenic and embedded remains cannot be interpreted as recent biological

Management of municipal solid waste incineration residues

International Nuclear Information System (INIS)

Sabbas, T.; Polettini, A.; Pomi, R.; Astrup, T.; Hjelmar, O.; Mostbauer, P.; Cappai, G.; Magel, G.; Salhofer, S.; Speiser, C.; Heuss-Assbichler, S.; Klein, R.; Lechner, P.

2003-01-01

The management of residues from thermal waste treatment is an integral part of waste management systems. The primary goal of managing incineration residues is to prevent any impact on our health or environment caused by unacceptable particulate, gaseous and/or solute emissions. This paper provides insight into the most important measures for putting this requirement into practice. It also offers an overview of the factors and processes affecting these mitigating measures as well as the short- and long-term behavior of residues from thermal waste treatment under different scenarios. General conditions affecting the emission rate of salts and metals are shown as well as factors relevant to mitigating measures or sources of gaseous emissions

Chemical activation of gasification carbon residue for phosphate removal

Science.gov (United States)

Kilpimaa, Sari; Runtti, Hanna; Lassi, Ulla; Kuokkanen, Toivo

2012-05-01

Recycling of waste materials provides an economical and environmentally significant method to reduce the amount of waste. Bioash formed in the gasification process possesses a notable amount of unburned carbon and therefore it can be called a carbon residue. After chemical activation carbon residue could be use to replace activated carbon for example in wastewater purification processes. The effect of chemical activation process variables such as chemical agents and contact time in the chemical activation process were investigated. This study also explored the effectiveness of the chemically activated carbon residue for the removal of phosphate from an aqueous solution. The experimental adsorption study was performed in a batch reactor and the influence of adsorption time, initial phosphate concentration and pH was studied. Due to the carbon residue's low cost and high adsorption capacity, this type of waste has the potential to be utilised for the cost-effective removal of phosphate from wastewaters. Potential adsorbents could be prepared from these carbonaceous by-products and used as an adsorbent for phosphate removal.

Carbonaceous aerosols over China--review of observations, emissions, and climate forcing.

Science.gov (United States)

Wang, Linpeng; Zhou, Xuehua; Ma, Yujie; Cao, Zhaoyu; Wu, Ruidong; Wang, Wenxing

2016-01-01

Carbonaceous aerosols have been attracting attention due to the influence on visibility, air quality, and regional climate. Statistical analyses based on concentration levels, spatial-temporal variations, correlations, and organic carbon (OC) to element carbon (EC) ratios from published data of OC and EC in particulate matter (PM2.5 and PM10) were carried out in order to give a carbonaceous aerosol profile in China. The results showed maxima for OC of 29.5 ± 18.2 μg C m(-3) and for EC of 8.4 ± 6.3 μg C m(-3) in winter and minima for OC of 12.9 ± 7.7 μg C m(-3) in summer and for EC of 4.6 ± 2.8 μg C m(-3) in spring. In addition, OC and EC both had higher concentrations in urban than those in rural sites. Carbonaceous aerosol levels in China are about three to seven times higher compared to those in the USA and Europe. OC and EC occupied 20 ± 6 and 7 ± 3% of PM2.5 mass and 17 ± 7 and 5 ± 3% of PM10 mass, respectively, implying that carbonaceous aerosols are the main component of PM, especially OC. Secondary organic carbon (SOC) was a significant portion of PM and contributed 41 ± 26% to OC and 8 ± 6% to PM2.5 mass. The OC/EC ratio was 3.63 ± 1.73, which, along with the good correlation between OC and EC and the OC to EC slope of 2.29, signifies that coal combustion and/or vehicular exhaust is the dominated carbonaceous aerosol source in China. These provide a primary observation-based understanding of carbonaceous aerosol pollution in China and have a great significance in improving the emission inventory and climate forcing evaluation.

Indigenous Carbonaceous Matter in the Nakhla Mars Meteorite

Science.gov (United States)

Clemett, S. J.; Thomas-Keprta, K. L.; Rahman, Z.; Le, L.; Wentworth, S. J.; Gibson, E. K.; McKay, D. S.

2016-01-01

Detailed microanalysis of the Martian meteorite Nakhla has shown there are morphologically distinct carbonaceous features spatially associated with low-T aqueous alteration phases including salts and id-dingsite. A comprehensive suite of analytical instrumentation including optical microscopy, field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) spectroscopy, focused ion beam (FIB) microscopy, transmission electron microscopy (TEM), two-step laser mass spectrometry (mu-L(sup 2)MS), laser mu-Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), and nanoscale secondary ion mass spectrometry (NanoSIMS) are being used to characterize the carbonaceous matter and host mineralogy. The search for carbonaceous matter on Mars has proved challenging. Viking Landers failed to unambiguously detect simple organics at either of the two landing sites although the Martian surface is estimated to have acquired at least 10(exp15) kg of C as a consequence of meteoritic accretion over the last several Ga. The dearth of organics at the Martian surface has been attributed to various oxidative processes including UV photolysis and peroxide activity. Consequently, investigations of Martian organics need to be focused on the sub-surface regolith where such surface processes are either severely attenuated or absent. Fortuitously since Martian meteorites are derived from buried regolith materials they provide a unique opportunity to study Martian organic geochemistry.

Carbonaceous species in atmospheric aerosols from the Krakow area (Malopolska District: carbonaceous species dry deposition analysis

Directory of Open Access Journals (Sweden)

Szramowiat Katarzyna

2016-01-01

Full Text Available Organic and elemental carbon content in PM10 was studied at three sites in Malopolska District representing the city centre (Krakow, rural/residential (Bialka and residential/industrial environments (Krakow. The PM10 samples were collected during the winter time study. The highest concentrations of carbonaceous species were observed in Skawina (36.9 μg·m-3 of OC and 9.6 μg·m-3 of EC. The lowest OC and EC concentrations were reported in Krakow (15.2 μg·m-3 and 3.9 μg·m-3, respectively. The highest concentration of carbonaceous species and the highest wind velocities in Skawina influenced the highest values of the dry deposition fluxes. Correlations between OC, EC and chemical constituents and meteorological parameters suggest that a Krakow was influenced by local emission sources and temperature inversion occurrence; b Bialka was under the influence of local emission sources and long-range transport of particles; c Skawina was impacted by local emission sources.

Laboratory Experiments on the Low-temperature Formation of Carbonaceous Grains in the ISM

Science.gov (United States)

Fulvio, Daniele; Góbi, Sándor; Jäger, Cornelia; Kereszturi, Ákos; Henning, Thomas

2017-11-01

The life cycle of cosmic dust grains is far from being understood and the origin and evolution of interstellar medium (ISM) grains is still under debate. In the ISM, the cosmic dust destruction rate is faster than the production rate by stellar sources. However, observations of ISM refractory matter suggest that to maintain a steady amount of cosmic grains, some supplementary production mechanism takes place. In this context, we aimed to study possible reformation mechanisms of cosmic grains taking place at low temperature directly in the ISM. The low-temperature condensation of carbonaceous materials has been investigated in experiments mimicking the ISM conditions. Gas-phase carbonaceous precursors created by laser ablation of graphite were forced to accrete on cold substrates (T ≈ 10 K) representing surviving dust grains. The growing and evolution of the condensing carbonaceous precursors have been monitored by MIR and UV spectroscopy under a number of experimental scenarios. For the first time, the possibility to form ISM carbonaceous grains in situ is demonstrated. The condensation process is governed by carbon chains that first condense into small carbon clusters and finally into more stable carbonaceous materials, of which structural characteristics are comparable to the material formed in gas-phase condensation experiments at very high temperature. We also show that the so-formed fullerene-like carbonaceous material is transformed into a more ordered material under VUV processing. The cold condensation mechanisms discussed here can give fundamental clues to fully understand the balance between the timescale for dust injection, destruction, and reformation in the ISM.

Microwave assisted synthesis of luminescent carbonaceous nanoparticles from silk fibroin for bioimaging.

Science.gov (United States)

Gao, Hongzhi; Teng, Choon Peng; Huang, Donghong; Xu, Wanqing; Zheng, Chaohui; Chen, Yisong; Liu, Minghuan; Yang, Da-Peng; Lin, Ming; Li, Zibiao; Ye, Enyi

2017-11-01

Bombyx mori silk as a natural protein based biopolymer with high nitrogen content, is abundant and sustainable because of its mass product all over the world per year. In this study, we developed a facile and fast microwave-assisted synthesis of luminescent carbonaceous nanoparticles using Bombyx mori silk fibroin and silk solution as the precursors. As a result, the obtained carbonaceous nanoparticles exhibit a photoluminescence quantum yield of ~20%, high stability, low cytotoxicity, high biocompatibility. Most importantly, we successfully demonstrated bioimaging using these luminescent carbonaceous nanoparticles with excitation dependent luminescence. In addition, the microwave-assisted hydrothermal method can be extended to convert other biomass into functional nanomaterials. Copyright © 2017 Elsevier B.V. All rights reserved.

Evaluation of early Archean volcaniclastic and volcanic flow rocks as possible sites for carbonaceous fossil microbes.

Science.gov (United States)

Walsh, Maud M

2004-01-01

Sedimentary rocks have traditionally been the focus of the search for Archean microfossils; the Earth's oldest fossil bacteria are associated with carbonaceous matter in sedimentary cherts in greenstone belts in the eastern Pilbara block of Western Australia and Barberton greenstone belt of South Africa. Reports of possible fossils in a martian meteorite composed of igneous rock and the discovery of modern bacteria associated with basalts have stimulated a new look at Archean volcanic rocks as possible sites for fossil microbes. This study examines silicified volcaniclastic rocks, near-surface altered volcanic flow rocks, and associated stromatolite- like structures from the Archean Barberton greenstone belt to evaluate their potential for the preservation of carbonaceous fossils. Detrital carbonaceous particles are widely admixed with current-deposited debris. Carbonaceous matter is also present in altered volcanic flow rocks as sparse particles in silica veins that appear to be fed by overlying carbonaceous chert layers. Neither microfossils nor mat-like material was identified in the altered volcanic rocks or adjacent stromatolite-like structures. Ancient volcanic flow and volcaniclastic rocks are not promising sites for carbonaceous fossil preservation.

Preconcentration of Trace Neonicotinoid Insecticide Residues Using Vortex-Assisted Dispersive Micro Solid-Phase Extraction with Montmorillonite as an Efficient Sorbent

Directory of Open Access Journals (Sweden)

Khwankaew Moyakao

2018-04-01

Full Text Available In this work, we investigated montmorillonite for adsorption of neonicotinoid insecticides in vortex-assisted dispersive micro-solid phase extraction (VA-d-μ-SPE. High-performance liquid chromatography with photodiode array detection was used for quantification and determination of neonicotinoid insecticide residues, including thiamethoxam, clothianidin, imidacloprid, acetamiprid, and thiacloprid. In this method, the solid sorbent was dispersed into the aqueous sample solution and vortex agitation was performed to accelerate the extraction process. Finally, the solution was filtered from the solid sorbent with a membrane filter. The parameters affecting the extraction efficiency of the proposed method were optimized, such as amount of sorbent, sample volume, salt addition, type and volume of extraction solvent, and vortex time. The adsorbing results show that montmorillonite could be reused at least 4 times and be used as an effective adsorbent for rapid extraction/preconcentration of neonicotinoid insecticide residues. Under optimum conditions, linear dynamic ranges were achieved between 0.5 and 1000 ng mL−1 with a correlation of determination (R2 greater than 0.99. Limit of detection (LOD ranged from 0.005 to 0.065 ng mL−1, while limit of quantification (LOQ ranged from 0.008 to 0.263 ng mL−1. The enrichment factor (EF ranged from 8 to 176-fold. The results demonstrated that the proposed method not only provided a more simple and sensitive method, but also can be used as a powerful alternative method for the simultaneous determination of insecticide residues in natural surface water and fruit juice samples.

Solid phase microextraction sampling of high explosive residues in the presence of radionuclides and radionuclide surrogate metals

International Nuclear Information System (INIS)

Duff, M.C.; Crump, S.L.; Ray, R.J.; Beals, D.; Cotham, W.E.; Mount, K.; Koons, R.D.; Leggitt, J.

2008-01-01

The Federal Bureau of Investigation (FBI) Laboratory currently does not have on site facilities for handling radioactive evidentiary materials and there are no established FBI methods or procedures for decontaminating high explosive (HE) evidence while maintaining evidentiary value. One experimental method for the isolation of HE residue involves using solid phase microextraction (SPME) fibers to remove residue of interest. Due to their high affinity for organics, SPME fibers should have little affinity for most metals. However, no studies have measured the affinity of radionuclides for SPME fibers. The focus of this research was to examine the affinity of dissolved radionuclide ( 239/240 Pu, 238 U, 237 Np, 85 Sr, 133 Ba, 137 Cs, 60 Co and 226 Ra) and stable radionuclide surrogate metals (Sr, Co, Ir, Re, Ni, Ba, Cs, Nb, Ru, and Nd) for SPME fibers at the exposure conditions that favor the uptake of HE residues. Our results from radiochemical and mass spectrometric analyses indicate these metals have little measurable affinity for these SPME fibers during conditions that are conducive to HE residue uptake with subsequent analysis by liquid or gas phase chromatography with mass spectrometric detection. (author)

Thermal inertializing of solid incinerator residues

International Nuclear Information System (INIS)

Proelss, J.

2003-01-01

Inertialization of residues is a key task of incinerators. Residues of conventional incineration processes may contain high levels of inorganic or organic pollutants and must be treated prior to recycling. the most effective process is thermal treatment above the melting point. This will destroy organic pollutants like dioxins/furans and pathogenic compounds, while the heavy metals will be partly volatilized. The glassy slag obtained as end product is low in heavy metals and more or less resistant to leaching. The The author describes a method for calculating activity coefficients of volatile components of diluted, liquid multicomponent systems. With these data, the data base for thermodynamic description of fluid mixtures was updated, and a set of characteristic data was established for describing transport in an inflatable module. Once the activity coefficients of interesting constituents of the slag are known along with the transport conditions in the volatilization process, it is possible to optimize the thermal treatment of critical ashes and dusts with a view to energy consumption and process control. In two different exemplary process concepts, the energy consumption for residue treatment is estimated. The processes proposed are compared with published process proposals, and their energy consumption is assessed in a comoparative study [de

Carbonaceous Aerosols in Fine Particulate Matter of Santiago Metropolitan Area, Chile

Science.gov (United States)

Toro Araya, Richard; Flocchini, Robert; Morales Segura, Rául G. E.; Leiva Guzmán, Manuel A.

2014-01-01

Measurements of carbonaceous aerosols in South American cities are limited, and most existing data are of short term and limited to only a few locations. For 6 years (2002–2007), concentrations of fine particulate matter and organic and elemental carbon were measured continuously in the capital of Chile. The contribution of carbonaceous aerosols to the primary and secondary fractions was estimated at three different sampling sites and in the warm and cool seasons. The results demonstrate that there are significant differences in the levels in both the cold (March to August) and warm (September to February) seasons at all sites studied. The percent contribution of total carbonaceous aerosol fine particulate matter was greater in the cool season (53 ± 41%) than in the warm season (44 ± 18%). On average, the secondary organic carbon in the city corresponded to 29% of the total organic carbon. In cold periods, this proportion may reach an average of 38%. A comparison of the results with the air quality standards for fine particulate matter indicates that the total carbonaceous fraction alone exceeds the World Health Organization standard (10 µg/m3) and the United States Environmental Protection Agency standard (15 µg/m3) for fine particulate matter. PMID:24587753

Carbonaceous Aerosols in Fine Particulate Matter of Santiago Metropolitan Area, Chile

Directory of Open Access Journals (Sweden)

Richard Toro Araya

2014-01-01

Full Text Available Measurements of carbonaceous aerosols in South American cities are limited, and most existing data are of short term and limited to only a few locations. For 6 years (2002–2007, concentrations of fine particulate matter and organic and elemental carbon were measured continuously in the capital of Chile. The contribution of carbonaceous aerosols to the primary and secondary fractions was estimated at three different sampling sites and in the warm and cool seasons. The results demonstrate that there are significant differences in the levels in both the cold (March to August and warm (September to February seasons at all sites studied. The percent contribution of total carbonaceous aerosol fine particulate matter was greater in the cool season (53 ± 41% than in the warm season (44 ± 18%. On average, the secondary organic carbon in the city corresponded to 29% of the total organic carbon. In cold periods, this proportion may reach an average of 38%. A comparison of the results with the air quality standards for fine particulate matter indicates that the total carbonaceous fraction alone exceeds the World Health Organization standard (10 µg/m3 and the United States Environmental Protection Agency standard (15 µg/m3 for fine particulate matter.

Carbonaceous aerosols in fine particulate matter of Santiago Metropolitan Area, Chile.

Science.gov (United States)

Toro Araya, Richard; Flocchini, Robert; Morales Segura, Rául G E; Leiva Guzmán, Manuel A

2014-01-01

Measurements of carbonaceous aerosols in South American cities are limited, and most existing data are of short term and limited to only a few locations. For 6 years (2002-2007), concentrations of fine particulate matter and organic and elemental carbon were measured continuously in the capital of Chile. The contribution of carbonaceous aerosols to the primary and secondary fractions was estimated at three different sampling sites and in the warm and cool seasons. The results demonstrate that there are significant differences in the levels in both the cold (March to August) and warm (September to February) seasons at all sites studied. The percent contribution of total carbonaceous aerosol fine particulate matter was greater in the cool season (53 ± 41%) than in the warm season (44 ± 18%). On average, the secondary organic carbon in the city corresponded to 29% of the total organic carbon. In cold periods, this proportion may reach an average of 38%. A comparison of the results with the air quality standards for fine particulate matter indicates that the total carbonaceous fraction alone exceeds the World Health Organization standard (10 µg/m(3)) and the United States Environmental Protection Agency standard (15 µg/m(3)) for fine particulate matter.

Geopolymers based on the valorization of Municipal Solid Waste Incineration residues

Science.gov (United States)

Giro-Paloma, J.; Maldonado-Alameda, A.; Formosa, J.; Barbieri, L.; Chimenos, J. M.; Lancellotti, I.

2017-10-01

The proper management of Municipal Solid Waste (MSW) has become one of the main environmental commitments for developed countries due to the uncontrolled growth of waste caused by the consumption patterns of modern societies. Nowadays, municipal solid waste incineration (MSWI) is one of the most feasible solutions and it is estimated to increase in Europe where the accessibility of landfill is restricted. Bottom ash (BA) is the most significant by-product from MSWI as it accounts for 85 - 95 % of the solid product resulting from combustion, which is classified as a non-hazardous residue that can be revalorized as a secondary aggregate in road sub-base, bulk lightweight filler in construction. In this way, revalorization of weathered BA (WBA) for the production of geopolymers may be a good alternative to common reuse as secondary aggregate material; however, the chemical process to obtain these materials involves several challenges that could disturb the stability of the material, mainly from the environmental point of view. Accordingly, it is necessary that geopolymers are able to stabilize heavy metals contained in the WBA in order to be classified as non-hazardous materials. In this regard, the SiO2/Al2O3 ratio plays an important role for the encapsulation of heavy metals and other toxic elements. The aim of this research is to formulate geopolymers starting from the 0 - 2 mm particle size fraction of WBA, as a unique raw material used as aluminumsilicate precursor. Likewise, leaching tests of the geopolymers formulated were performed to assess their environmental impact. The findings show that it is possible to formulate geopolymers using 100 % WBA as precursor, although more investigations are needed to sustain that geopolymer obtained can be considered as non-hazardous materials.

Pulmonary exposure to carbonaceous nanomaterials and sperm quality

DEFF Research Database (Denmark)

Skovmand, Astrid; Lauvas, Anna Jacobsen; Christensen, Preben

2018-01-01

. Pulmonary inflammation was determined by differential cell count in bronchoalveolar lavage fluid. Epididymal sperm concentration and motility were measured by computer-assisted sperm analysis. Epididymal sperm viability and morphological abnormalities were assessed manually using Hoechst 33,342/PI...... inflammation is a potential modulator of endocrine function. The aim of this study was to investigate the effects of pulmonary exposure to carbonaceous nanomaterials on sperm quality parameters in an experimental mouse model.Methods: Effects on sperm quality after pulmonary inflammation induced by carbonaceous...... flourescent and Spermac staining, respectively. Epididymal sperm were assessed with regard to sperm DNA integrity (damage). Daily sperm production was measured in the testis, and testosterone levels were measured in blood plasma by ELISA.Results: Neutrophil numbers in the bronchoalveolar fluid showed...

Treating distillable carbonaceous materials with hydrocarbon gases, etc

Energy Technology Data Exchange (ETDEWEB)

1935-12-04

A process is described for the treatment of distillable carbonaceous materials with hydrogen gases in the presence of hydrogen halides to recover valuable hydrocarbon products, characterized by the stable halide forming the treating medium for the hot-test gasesous product of this treatment with hydrogen gases in combination with an alkaline metal or alkaline earth, able to be decomposed by an inorganic acid soluble in water, capable of driving off hydrogen halide from their salts and also with salts of ammonia of the mentioned inorganic acids, the halide being converted into halide of ammonia and halogen, and the ammonia halide or hydrogen halide being returned to the process alone or together with the feed of carbonaceous materials with which it began.

Radiocarbon: nature's tracer for carbonaceous pollutants

International Nuclear Information System (INIS)

Currie, L.A.; Klouda, G.A.; Gerlach, R.W.

1982-01-01

Recent developments in radiocarbon dating techniques have made it feasible to determine 14 C/ 12 C ratios in samples containing milligram or even microgram quantities of carbon. As a result, it has become practicable to apply these techniques to the study of trace gases and particles in the atmosphere, as a means of resolving anthropogenic from natural source components. Interpretation of 14 C data is straightforward: biospheric carbon (such as vegetation) is alive with a 14 C/ 12 C ratio of about 1.5 x 10 -12 , whereas fossil carbon is dead. Beyond this dichotomous classification it becomes very interesting to combine the isotopic data with concurrent chemical data, as well as spatial and temporal distributions, in order to infer the strengths of specific sources of carbonaceous pollutants. A brief review will be presented of our program on atmospheric gases and carbonaceous particles. For the latter, we have assayed individual chemical and size fractions, and samples collected in urban, rural, and remote locales. The biogenic carbon fraction - presumably from wood-burning - ranged from 10% to 100% for the urban samples analyzed

Agrochemical characterisation of the solid by-products and residues from the winery and distillery industry.

Science.gov (United States)

Bustamante, M A; Moral, R; Paredes, C; Pérez-Espinosa, A; Moreno-Caselles, J; Pérez-Murcia, M D

2008-01-01

The winery and distillery industry produces a great quantity of residues, whose management and disposal are environmental problems due to their seasonal character and some polluting characteristics. The main solid by-products and residues generated are grape stalk, grape pomace or marc, wine lee, exhausted grape marc and winery sludge. In this study, 87 samples of winery and distillery residues were collected from different Spanish wineries and distilleries. Electrical conductivity, pH, total organic matter, organic carbon, polyphenols and contents of plant nutrients and heavy metals were determined. The purpose of this research was to study the composition of these wastes and to find relationships in order to use easily analysable parameters to estimate their composition. In general, the winery and distillery residues showed low pH (mean values ranged from 3.8 to 6.8) and electrical conductivity values (1.62-6.15 dS m(-1)) and high organic matter (669-920 g kg(-1)) and macronutrient contents, especially in K (11.9-72.8 g kg(-1)). However, a notable polyphenol concentration (1.2-19.0 g kg(-1)) and low micronutrient and heavy metal contents were also observed, some of these properties being incompatible with agricultural requirements. Therefore, conditioning treatments are necessary prior to possible use of these wastes. In all wastes, significant correlations were found between easily determined parameters, such as pH, electrical conductivity and total organic matter, and most of the parameters studied. The regression models obtained are also discussed.

Nutrient assessment of olive leaf residues processed by solid-state fermentation as an innovative feedstuff additive.

Science.gov (United States)

Xie, P-J; Huang, L-X; Zhang, C-H; Zhang, Y-L

2016-07-01

Olive leaf residue feedstuff additives were prepared by solid-state fermentation (SSF), and its feeding effects on broiler chickens were examined. The fermentation's nutrient value, that is, protein enrichment, cellulase activity, tannic acid degradation and amino acid enhancement, was determined. The effect of different strains, including molds (Aspergillus niger, Aspergillus oryzae and Trichoderma viride) and yeasts (Candida utilis, Candida tropicalis and Geotrichum candidum), and the fermentation time on the nutrient values of the feedstuff additives was investigated. The experimental results showed that the optimal parameters for best performance were A. niger and C. utilis in a 1 : 1 ratio (v/v) in co-culture fermentation for 5 days. Under these conditions, the total content of amino acids in the fermented olive leaf residues increased by 22·0% in comparison with that in the raw leaf residues. Both Glutamic acid and Aspartic acid contents were increased by more than 25·4%. Broiler chickens fed with different amounts of feedstuff additives were assessed. The results demonstrated that the chicken weight gains increased by 120%, and normal serum biochemical parameters were improved significantly after 10% of the feedstuff additives were supplemented to the daily chicken feed for 28 days. The co-culture combination of A. niger and C. utilis with SSF for olive leaf residue had the best nutrient values. The addition of 10% fermented olive leaf residue facilitated the chicken growth and development. This study reveals that olive leaf residues fermented by SSF exhibited considerable potential as feed additives for feeding poultry. © 2016 The Society for Applied Microbiology.

Use of solid residue from the olive industry

Directory of Open Access Journals (Sweden)

Guinda, Ángeles

2006-03-01

Full Text Available Research into finding new uses for olive products, particularly by-products of olive oil production, is of great relevance not only to the economy, but also to the environment, in the towns where olives are grown. A large number of research articles has been published dealing with the chemical composition of olives and olive oil; however, only a few studies have centered on isolating and identifying compounds in the olive leaf. In this article an overview of the present body of knowledge on the chemical composition of the olive leaf will be presented. Also to be discussed is the use of solid residue, namely, the olive leaf and the olive stone. Both of these types of residue result from olive oil and table olive production, and can be used as a renewable energy source, as well as to obtain high added-value compounds. The latter, bioactive compounds are directed towards the cosmetic, pharmaceutical, and natural food supplements markets, all of which are currently highly receptive to products of natural origin.La investigación de nuevos aprovechamientos del olivar y en particular de lo subproductos del proceso de producción del aceite, tiene gran relevancia tanto en la economía como en el medio ambiente de los pueblos donde se desarrolla este cultivo. Son numerosos los trabajos publicados sobre la composición química de la aceituna y el aceite de oliva, en cambio sólo existen algunos estudios sobre el aislamiento e identificación de los compuestos de la hoja de olivo, en esta contribución se revisan los conocimientos sobre la composición química de la hoja de olivo, así como, las utilizaciones de los residuos sólidos -hoja de olivo y hueso de aceituna- que se originan en la producción del aceite de oliva y de aceitunas de mesa, como energía renovable y para la obtención de compuestos de alto valor añadido. Estos últimos, compuestos bioactivos dirigidos a los mercados de los aditivos alimentarios naturales, farmacéutico y cosm

Explosive Characteristics of Carbonaceous Nanoparticles

Science.gov (United States)

Turkevich, Leonid; Fernback, Joseph; Dastidar, Ashok

2013-03-01

Explosion testing has been performed on 20 codes of carbonaceous particles. These include SWCNTs (single-walled carbon nanotubes), MWCNTs (multi-walled carbon nanotubes), CNFs (carbon nanofibers), graphene, diamond, fullerene, carbon blacks and graphites. Explosion screening was performed in a 20 L explosion chamber (ASTM E1226-10 protocol), at a (dilute) concentration of 500 g/m3, using a 5 kJ ignition source. Time traces of overpressure were recorded. Samples exhibited overpressures of 5-7 bar, and deflagration index KSt = V1/3 (dp/pt)max ~ 10 - 80 bar-m/s, which places these materials in European Dust Explosion Class St-1 (similar to cotton and wood dust). There was minimal variation between these different materials. The explosive characteristics of these carbonaceous powders are uncorrelated with particle size (BET specific surface area). Additional tests were performed on selected materials to identify minimum explosive concentration [MEC]. These materials exhibit MEC ~ 101 -102 g/m3 (lower than the MEC for coals). The concentration scans confirm that the earlier screening was performed under fuel-rich conditions (i.e. the maximum over-pressure and deflagration index exceed the screening values); e.g. the true fullerene KSt ~ 200 bar-m/s, placing it borderline St-1/St-2. Work supported through the NIOSH Nanotechnology Research Center (NTRC)

Co-production of bio-ethanol, xylonic acid and slow-release nitrogen fertilizer from low-cost straw pulping solid residue.

Science.gov (United States)

Huang, Chen; Ragauskas, Arthur J; Wu, Xinxing; Huang, Yang; Zhou, Xuelian; He, Juan; Huang, Caoxing; Lai, Chenhuan; Li, Xin; Yong, Qiang

2018-02-01

A novel bio-refinery sequence yielding varieties of co-products was developed using straw pulping solid residue. This process utilizes neutral sulfite pretreatment which under optimal conditions (160 °C and 3% (w/v) sulfite charge) provides 64.3% delignification while retaining 90% of cellulose and 67.3% of xylan. The pretreated solids exhibited excellent enzymatic digestibility, with saccharification yields of 86.9% and 81.1% for cellulose and xylan, respectively. After pretreatment, the process of semi-simultaneous saccharification and fermentation (S-SSF) and bio-catalysis was investigated. The results revealed that decreased ethanol yields were achieved when solid loading increased from 5% to 30%. An acceptable ethanol yield of 76.8% was obtained at 20% solid loading. After fermentation, bio-catalysis of xylose remaining in fermentation broth resulted in near 100% xylonic acid (XA) yield at varied solid loadings. To complete the co-product portfolio, oxidation ammoniation of the dissolved lignin successfully transformed it into biodegradable slow-release nitrogen fertilizer with excellent agricultural properties. Copyright © 2017 Elsevier Ltd. All rights reserved.

Approaching zero cellulose loss in cellulose nanocrystal (CNC) production: recovery and characterization of cellulosic solid residues (CSR) and CNC

Science.gov (United States)

Q.Q. Wang; J.Y. Zhu; R.S. Reiner; S.P. Verrill; U. Baxa; S.E. McNeil

2012-01-01

This study demonstrated the potential of simultaneously recovering cellulosic solid residues (CSR) and producing cellulose nanocrystals (CNCs) by strong sulfuric acid hydrolysis to minimize cellulose loss to near zero. A set of slightly milder acid hydrolysis conditions than that considered as “optimal” were used to significantly minimize the degradation of cellulose...

Fungal-Transformation of Surrogate Sulphides and Carbonaceous ...

African Journals Online (AJOL)

In the recovery of gold from refractory gold ores, pretreatment is required to decompose sulphides and liberate occluded gold before cyanidation, and to deactivate carbonaceous matter and prevent it from adsorbing dissolved gold. Until the past three decades, most commercial pretreatment processes had been by abiotic ...

Slurry burner for mixture of carbonaceous material and water

Science.gov (United States)

Nodd, D.G.; Walker, R.J.

1985-11-05

The present invention is intended to overcome the limitations of the prior art by providing a fuel burner particularly adapted for the combustion of carbonaceous material-water slurries which includes a stationary high pressure tip-emulsion atomizer which directs a uniform fuel into a shearing air flow as the carbonaceous material-water slurry is directed into a combustion chamber, inhibits the collection of unburned fuel upon and within the atomizer, reduces the slurry to a collection of fine particles upon discharge into the combustion chamber, and regulates the operating temperature of the burner as well as primary air flow about the burner and into the combustion chamber for improved combustion efficiency, no atomizer plugging and enhanced flame stability.

Apparatus for the distillation of coal, shale or other carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Wilson, P

1932-02-16

The design consists of a retort having a series of joined closed superheated sections each having a heavier gas delivery port therefrom leading to an outlet pipe in combination with a condenser, means above and on said sections comprising a series of hoppers in communication with a common feed hopper for carbonaceous materials to be distilled. An air tight cover for said feed hopper and intermediate rotatable valve control are provided. Means are provided for said carbonaceous material between said hoppers and said sections and adjacent means having lighter gas ports to a pipe also in communication with said condenser. A series of exit hoppers are located below such sections and means for feeding preheated gas through the exit hoppers to the material to be distilled are provided. A rotatable valve control means associated with the exit hoppers for discharging spent carbonaceous materials to separate water sealed outlets to a tank located below the apparatus.

Carbonaceous Asteroid Volatile Recovery (CAVoR) system, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — The Carbonaceous Asteroid Volatile Recovery (CAVoR) system produces water and hydrogen-rich syngas for propellant production, life support consumables, and...

Aqueous processing of organic compounds in carbonaceous asteroids

Science.gov (United States)

Trigo-Rodríguez, Josep Maria; Rimola, Albert; Martins, Zita

2015-04-01

There is growing evidence pointing towards a prebiotic synthesis of complex organic species in water-rich undifferentiated bodies. For instance, clays have been found to be associated with complex organic compounds (Pearson et al. 2002; Garvie & Buseck 2007; Arteaga et al. 2010), whereas theoretical calculations have studied the interaction between the organic species and surface minerals (Rimola et al., 2013) as well as surface-induced reactions (Rimola at al. 2007). Now, we are using more detailed analytical techniques to study the possible processing of organic molecules associated with the mild aqueous alteration in CR, CM and CI chondrites. To learn more about these processes we are studying carbonaceous chondrites at Ultra High-Resolution Transmission Electron Microscopy (UHR-TEM). We are particularly interested in the relationship between organics and clay minerals in carbonaceous chondrites (CCs) matrixes (Trigo-Rodríguez et al. 2014, 2015).We want to address two goals: i) identifying the chemical steps in which the organic molecules could have increased their complexity (i.e., surface interaction and catalysis); and ii) studying if the organic matter present in CCs experienced significant processing concomitant to the formation of clays and other minerals at the time in which these planetary bodies experienced aqueous alteration. Here, these two points are preliminarily explored combing experimental results with theoretical calculations based on accurate quantum mechanical methods. References Arteaga O, Canillas A, Crusats J, El-Hachemi Z, Jellison GE, Llorca J, Ribó JM (2010) Chiral biases in solids by effect of shear gradients: a speculation on the deterministic origin of biological homochirality. Orig Life Evol Biosph 40:27-40. Garvie LAJ, Buseck PR (2007) Prebiotic carbon in clays from Orgueil and Ivuna (CI) and Tagish lake (C2 ungrouped) meteorites. Meteorit Planet Sci 42:2111-2117. Pearson VK, Sephton MA, Kearsley AT, Bland AP, Franchi IA, Gilmour

Retorts for distilling carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Lutz, H E

1921-09-12

A retort for distilling carbonaceous material is described in which a mass of such material is retained in a pocket formed between an outer wall and an internal wall which is perforated to permit the free escape of distilled products, the retorts having heating means that directly heat the retort but are so related to the pocket that the material therein is heated indirectly and simultaneously from all sides entirely by heat conducted thereto by the walls.

Chemical, structural and combustion characteristics of carbonaceous products obtained by hydrothermal carbonization of palm empty fruit bunches.

Science.gov (United States)

Parshetti, Ganesh K; Kent Hoekman, S; Balasubramanian, Rajasekhar

2013-05-01

A carbon-rich solid product, denoted as hydrochar, was synthesized by hydrothermal carbonization (HTC) of palm oil empty fruit bunch (EFB), at different pre-treatment temperatures of 150, 250 and 350 °C. The conversion of the raw biomass to its hydrochar occurred via dehydration and decarboxylation processes. The hydrochar produced at 350 °C had the maximum energy-density (>27 MJ kg(-1)) with 68.52% of raw EFB energy retained in the char. To gain a detailed insight into the chemical and structural properties, carbonaceous hydrochar materials were characterized by FE-SEM, FT-IR, XRD and Brunauer-Emmett-Teller (BET) analyses. This work also investigated the influence of hydrothermally treated hydrochars on the co-combustion characteristics of low rank Indonesian coal. Conventional thermal gravimetric analysis (TGA) parameters, kinetics and activation energy of different hydrochar and coal blends were estimated. Our results show that solid hydrochars improve the combustion of low rank coals for energy generation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Carbonaceous Aerosol Characterization during 2016 KOR-US 2016

Science.gov (United States)

Rodriguez, B.; Santos, G. M.; Sanchez, D.; Jeong, D.; Czimczik, C. I.; Kim, S.

2017-12-01

Atmospheric carbonaceous aerosols are a major component of fine particulate matter and assume important roles in Earth's climate and human health. Because atmospheric carbonaceous aerosols exist as a continuum ranging from small, light-scattering organic carbon (OC), to highly-condensed, light-absorbing elemental carbon (EC) they have contrasting effects on interaction with incoming and outgoing radiation, cloud formation, and snow/ice albedo. By strengthening our understanding of the relative contribution and sources of OC and EC we will be able to further describe aerosol formation and mixing at the regional level. To understand the relative anthropogenic and biogenic contributions to carbonaceous aerosol, 12 PM10 aerosols samples were collected on quartz fiber filters at the Mt. Taewha Research Forest in South Korea during the KORUS-AQ 2016 campaign over periods of 24-48 hours with a high-volume air sampler. Analysis of bulk C and N concentrations and absorption properties of filter extracts interspersed with HYSPLIT model results indicated that continental outflow across the Yellow Sea in enriched in bulk nitrogen loading and enhanced bulk absorptive properties of the aerosols. Bulk radiocarbon analysis also indicated enriched values in all samples indicating contamination from a nuclear power plant or the combustion of biomedical waste nearby. Here, we aim to investigate further the chemical characterization of VOCs adsorbed unto the aerosol through TD-GC-TOFMS. With this dataset we aim to determine the relative contribution of anthropogenic and biogenic aerosols by utilizing specific chemical tracers for source apportionment.

Leaching From Biomass Gasification Residues

DEFF Research Database (Denmark)

Allegrini, Elisa; Boldrin, Alessio; Polletini, A.

2011-01-01

The aim of the present work is to attain an overall characterization of solid residues from biomass gasification. Besides the determination of chemical and physical properties, the work was focused on the study of leaching behaviour. Compliance and pH-dependence leaching tests coupled with geoche......The aim of the present work is to attain an overall characterization of solid residues from biomass gasification. Besides the determination of chemical and physical properties, the work was focused on the study of leaching behaviour. Compliance and pH-dependence leaching tests coupled...

Tunable atomic force microscopy bias lithography on electron beam induced carbonaceous platforms

Directory of Open Access Journals (Sweden)

Narendra Kurra

2013-09-01

Full Text Available Tunable local electrochemical and physical modifications on the carbonaceous platforms are achieved using Atomic force microscope (AFM bias lithography. These carbonaceous platforms are produced on Si substrate by the technique called electron beam induced carbonaceous deposition (EBICD. EBICD is composed of functionalized carbon species, confirmed through X-ray photoelectron spectroscopy (XPS analysis. AFM bias lithography in tapping mode with a positive tip bias resulted in the nucleation of attoliter water on the EBICD surface under moderate humidity conditions (45%. While the lithography in the contact mode with a negative tip bias caused the electrochemical modifications such as anodic oxidation and etching of the EBICD under moderate (45% and higher (60% humidity conditions respectively. Finally, reversible charge patterns are created on these EBICD surfaces under low (30% humidity conditions and investigated by means of electrostatic force microscopy (EFM.

Microwave-assisted and carbonaceous catalytic pyrolysis of crude glycerol from biodiesel waste for energy production

International Nuclear Information System (INIS)

Ng, Jo-Han; Leong, Swee Kim; Lam, Su Shiung; Ani, Farid Nasir; Chong, Cheng Tung

2017-01-01

Highlights: • Crude glycerol is pyrolysed catalytically via microwave irradiation to produce bioenergy. • Carbonaceous catalyst elevates pyrolysis temperature and promotes selectivity towards H_2 production. • Synthesis gas consisting of mainly H_2 and CH_4 was predominantly produced at long residence time and high temperature. • Production of bio-oil consisting of oxygenated compounds peaks at intermediate carrier gas flow rate. • Energy profit analysis shows positive energy gained with increasing residence time and decreasing reaction temperature. - Abstract: Biodiesel proliferation as a sustainable fuel has led to a glut of crude glycerol as co-product. This scenario made a previously lucrative co-product in the food and pharmaceutical sectors into a bioresource waste. The present study investigates the utilisation of a microwave-assisted pyrolysis technique to convert crude glycerol from biodiesel waste into usable bioenergy source. Operating conditions ranged from a temperature of 300–800 °C at carrier gas flow rates of 100–2000 mL/min, with the effects of carbonaceous catalyst on the selectivity of reaction pathway being investigated. Within the aforementioned conditions, the proportion of products phases is mainly dependent on the residence time inside the quartz reactor, followed by the reaction temperature. This is due to the combined factors of the reaction sequence and provision of activation energy to change product phases. The third factor of carbonaceous catalyst shows a predisposition towards hydrogen gas selectivity, leading to a lower overall gaseous product mass when factoring in products from all phases. An analysis of the energy content revealed that overall energy profit increases with decreasing temperature and increasing residence time. This concurs with solid energy content increasing in the same conditions, while it increases for liquid and gaseous products with decreasing temperature and flow rate, respectively. The

Cloud albedo increase from carbonaceous aerosol

Directory of Open Access Journals (Sweden)

W. R. Leaitch

2010-08-01

Full Text Available Airborne measurements from two consecutive days, analysed with the aid of an aerosol-adiabatic cloud parcel model, are used to study the effect of carbonaceous aerosol particles on the reflectivity of sunlight by water clouds. The measurements, including aerosol chemistry, aerosol microphysics, cloud microphysics, cloud gust velocities and cloud light extinction, were made below, in and above stratocumulus over the northwest Atlantic Ocean. On the first day, the history of the below-cloud fine particle aerosol was marine and the fine particle sulphate and organic carbon mass concentrations measured at cloud base were 2.4 μg m⁻³ and 0.9 μg m⁻³ respectively. On the second day, the below-cloud aerosol was continentally influenced and the fine particle sulphate and organic carbon mass concentrations were 2.3 μg m⁻³ and 2.6 μg m⁻³ respectively. Over the range 0.06–0.8 μm diameter, the shapes of the below-cloud size distributions were similar on both days and the number concentrations were approximately a factor of two higher on the second day. The cloud droplet number concentrations (CDNC on the second day were approximately three times higher than the CDNC measured on the first day. Using the parcel model to separate the influence of the differences in gust velocities, we estimate from the vertically integrated cloud light scattering measurements a 6% increase in the cloud albedo principally due to the increase in the carbonaceous components on the second day. Assuming no additional absorption by this aerosol, a 6% albedo increase translates to a local daytime radiative cooling of ∼12 W m⁻². This result provides observational evidence that the role of anthropogenic carbonaceous components in the cloud albedo effect can be much larger than that of anthropogenic sulphate, as some global simulations have indicated.

40 CFR 279.59 - Management of residues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Management of residues. 279.59 Section 279.59 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED... Management of residues. Owners and operators who generate residues from the storage, processing, or re...

Gasoline cars produce more carbonaceous particulate matter than modern filter-equipped diesel cars.

Science.gov (United States)

Platt, S M; El Haddad, I; Pieber, S M; Zardini, A A; Suarez-Bertoa, R; Clairotte, M; Daellenbach, K R; Huang, R-J; Slowik, J G; Hellebust, S; Temime-Roussel, B; Marchand, N; de Gouw, J; Jimenez, J L; Hayes, P L; Robinson, A L; Baltensperger, U; Astorga, C; Prévôt, A S H

2017-07-13

Carbonaceous particulate matter (PM), comprising black carbon (BC), primary organic aerosol (POA) and secondary organic aerosol (SOA, from atmospheric aging of precursors), is a highly toxic vehicle exhaust component. Therefore, understanding vehicle pollution requires knowledge of both primary emissions, and how these emissions age in the atmosphere. We provide a systematic examination of carbonaceous PM emissions and parameterisation of SOA formation from modern diesel and gasoline cars at different temperatures (22, -7 °C) during controlled laboratory experiments. Carbonaceous PM emission and SOA formation is markedly higher from gasoline than diesel particle filter (DPF) and catalyst-equipped diesel cars, more so at -7 °C, contrasting with nitrogen oxides (NO X ). Higher SOA formation from gasoline cars and primary emission reductions for diesels implies gasoline cars will increasingly dominate vehicular total carbonaceous PM, though older non-DPF-equipped diesels will continue to dominate the primary fraction for some time. Supported by state-of-the-art source apportionment of ambient fossil fuel derived PM, our results show that whether gasoline or diesel cars are more polluting depends on the pollutant in question, i.e. that diesel cars are not necessarily worse polluters than gasoline cars.

Quenched carbonaceous composite (QCC): a likely candidate for interstellar grains

International Nuclear Information System (INIS)

Sakata, A.; Wada, S.; Tanabe, T.; Onaka, T.

1984-01-01

The authors have recently reported that a carbonaceous composite synthesized from a hydrocarbon plasma shows an extinction property quite resembling the observed average interstellar extinction curve around the 220 nm hump. This composite is synthesized by quenching the excited gas ejecting from a plasma of methane gas, so it is called 'quenched carbonaceous composite' or 'QCC'. A recent study of QCC in the infrared region has shown that QCC can also account for some of the unidentified bands in the infrared region detected in several celestial objects. These results suggest that most of the pronounced features of the interstellar grains originate from substances whose major constituent is carbon. (author)

Carbonaceous aerosols from prescribed burning of a boreal forest ecosystem

International Nuclear Information System (INIS)

Mazurek, M.A.; Cofer, W.R. III; Levine, J.S.

1991-01-01

Smoke aerosol and background aerosol particles were collected from the controlled burning of boreal forest where vegetation species and relative mass distributions are known. Chemical mass balances were constructed for the total mass of carbonaceous aerosol particles emitted during the prescribed burn. In addition, a carbonaceous species inventory was developed for aerosol particles presnt under background, smoldering, and full-fire conditions; the production of organic carbon and elemental carbon particles is noted for these two fire regimes. Distributions of the solvent-soluble organic components of the sampled aerosols were generated to identify molecular properties that can be traced to unburned and pyrolyzed materials present in the boreal forest fuels

Carbonaceous aerosol at two rural locations in New York State: Characterization and behavior

Science.gov (United States)

Sunder Raman, Ramya; Hopke, Philip K.; Holsen, Thomas M.

2008-06-01

Fine particle samples were collected to determine the chemical constituents in PM2.5 at two rural background sites (Potsdam and Stockton, N. Y.) in the northeastern United States from November 2002 to August 2005. Samples were collected every third day for 24 h with a speciation network sampler. The measured carbonaceous species included thermal-optical organic carbon (OC), elemental carbon (EC), pyrolytic carbon (OP), black carbon (BC), and water-soluble, short-chain (WSSC) organic acids. Concentration time series, autocorrelations, and seasonal variations of the carbonaceous species were examined. During this multiyear period, the contributions of the total carbon (OC + EC) to the measured fine particle mass were 31.2% and 31.1% at Potsdam and Stockton, respectively. The average sum of the WSSC acids carbon accounted for approximately 2.5% of the organic carbon at Potsdam and 3.0% at Stockton. At Potsdam, the seasonal differences in the autocorrelation function (ACF) and partial autocorrelation function (PACF) values for carbonaceous species suggest that secondary formation may be an important contributor to the observed concentrations of species likely to be secondary in origin, particularly during the photochemically active time of the year (May to October). This study also investigated the relationships between carbonaceous species to better understand the behavior of carbonaceous aerosol and to assess the contribution of secondary organic carbon (SOC) to the total organic carbon mass (the EC tracer method was used to estimate SOC). At Potsdam the average SOC contribution to total OC varied between 66% and 72%, while at Stockton it varied between 58% and 64%.

Extraterrestrial Nucleobases in Carbonaceous Chondrites

Science.gov (United States)

Martins, Z.; Botta, O.; Fogel, M.; Sephton, M.; Glavin, D.; Watson, J.; Dworkin, J.; Schwartz, A.; Ehrenfreund, P.

Nucleobases in Carbonaceous Chondrites Z. Martins (1), O. Botta (2), M. L. Fogel (3), M. A. Sephton (4), D. P. Glavin (2), J. S. Watson (5), J. P. Dworkin (2), A. W. Schwartz (6) and P. Ehrenfreund (1,6). (1) Astrobiology Laboratory, Leiden Institute of Chemistry, Leiden, The Netherlands, (2) NASA Goddard Space Flight Center, Goddard Center for Astrobiology, Greenbelt, MD, USA, (3) GL, Carnegie Institution of Washington, Washington DC, USA, (4) Impacts and Astromaterials Research Centre, Department of Earth Science and Engineering, South Kensington Campus, Imperial College, London, UK, (5) Planetary and Space Sciences Research Institute, The Open University, Walton Hall, Milton Keynes, UK, (6) Radboud University Nijmegen, Nijmegen, The Netherlands. E-mail: z.martins@chem.leidenuniv.nl/Phone:+31715274440 Nucleobases are crucial compounds in terrestrial biochemistry, because they are key components of DNA and RNA. Carbonaceous meteorites have been analyzed for nucleobases by different research groups [1-5]. However, significant quantitative and qualitative differences were observed, leading to the controversial about the origin of these nucleobases. In order to establish the origin of these compounds in carbonaceous chondrites and to assess the plausibility of their exogenous delivery to the early Earth, we have performed formic acid extraction of samples of the Murchison meteorite [6], followed by an extensive purification procedure, analysis and quantification by high-performance liquid chromatography with UV absorption detection and gas chromatography-mass spectrometry. Our results were qualitatively consistent with previous results [3, 4], but showed significant quantitative differences. Compound specific carbon isotope values were obtained, using gas chromatography-combustion- isotope ratio mass spectrometry. A soil sample collected in the proximity of the Murchison meteorite fall site was subjected to the same extraction, purification and analysis procedure

Sorption characteristics and mechanisms of organic contaminant to carbonaceous biosorbents in aqueous solution

Institute of Scientific and Technical Information of China (English)

2008-01-01

A series of carbonaceous biosorbents was prepared by pyrolyzing pine needles,a model biomass,at various temperatures (100-700℃) under an oxygen-limited condition for 6h. The elemental composi-tions and the specific surface areas (BET-N2) of the biosorbents were analyzed. Sorption properties of 4-nitrotoluene to the biosorbents and their mechanisms were investigated,and then correlated with the structures of the biosorbents. The result shows that with the increase of the pyrolytic temperature,the aromaticity of the carbonaceous biosorbents increases dramatically and the polarity (the (N+O)/C atomic ratio) decreases sharply. Correspondingly,conformations of the organic matter in the biosor-bents transform gradually from a "soft-state" to a "hard-state" and the specific surface areas of the resultant biosorbents extend rapidly. The sorption isotherms fit well with the Freundlich equation. The regression parameters (i.e.,N and lgKf) are linearly related to the aromaticity indices (the H/C atomic ratio). Contributions of adsorption and partition to total sorption of the carbonaceous biosorbents are quantified. The adsorption of the carbonaceous biosorbents increases quickly with the increase of the pyrolytic temperature. The saturated adsorption amounts (Qmax) increase linearly with the increase of the specific surface areas (SA) of the biosorbents. For the carbonaceous biosorbents with hard-state carbon,the calculated normalized-Qmax values by SA are comparable to the theoretical estimation (2.45 μmol/m2). In comparison,for the carbonaceous sorbents with soft-state carbon,the calculated nor-malized-Qmax values by SA are much higher than the theoretical estimation. The partition coefficients (Kom) increase with the decrease of the polarity of the biosorbents,reaching a maximum,and then de-crease sharply with further decreasing the polarity,suggesting that partition mechanism be dominated by the compatibility and accessibility of the sorbent medium with organic

Sorption characteristics and mechanisms of organic contaminant to carbonaceous biosorbents in aqueous solution

Institute of Scientific and Technical Information of China (English)

CHEN BaoLiang; ZHOU DanDan; ZHU LiZhong; SHEN XueYou

2008-01-01

A series of carbonaceous biosorbents was prepared by pyrolyzing pine needles, a model biomass, at various temperatures (100-700℃) under an oxygen-limited condition for 6 h. The elemental composi-tions and the specific surface areas (BET-N2) of the biosorbents were analyzed. Sorption properties of 4-nitrotoluene to the biosorbents and their mechanisms were investigated, and then correlated with the structures of the biosorbents. The result shows that with the increase of the pyrolytic temperature, the sromaticity of the carbonaceous biosorbents increases dramatically and the polarity (the (N+O)/C atomic ratio) decreases sharply. Correspondingly, conformations of the organic matter in the biosor-bents transform gradually from a "soft-state" to a "hard-state" and the specific surface areas of the resultant biosorbents extend rapidly. The sorption isotherms fit well with the Freundlich equation. The regression parameters (I.e., N and IgKf) are linearly related to the aromaticity indices (the H/C atomic ratio). Contributions of adsorption and partition to total sorption of the carbonaceous biosorbents are quantified. The adsorption of the carbonaceous biosorbents increases quickly with the increase of the pyrolytic temperature. The saturated adsorption amounts (Qmax) increase linearly with the increase of the specific surface areas (SA) of the biosorbents. For the carbonaceous biosorbents with hard-state carbon, the calculated normalized-Qmax values by SA are comparable to the theoretical estimation (2.45 μmol/m2). In comparison, for the carbonaceous sorbents with soft-state carbon, the calculated nor-malized-Qmax values by SA are much higher than the theoretical estimation. The partition coefficients (Kom) increase with the decrease of the polarity of the biosorbents, reaching a maximum, and then de-crease sharply with further decreasing the polarity, suggesting that partition mechanism be dominated by the compatibility and accessibility of the sorbent medium with

40 CFR 279.67 - Management of residues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Management of residues. 279.67 Section 279.67 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED... for Energy Recovery § 279.67 Management of residues. Burners who generate residues from the storage or...

40 CFR 279.47 - Management of residues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Management of residues. 279.47 Section 279.47 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED... Management of residues. Transporters who generate residues from the storage or transport of used oil must...

縄文土器のAMS^14C年代(2)

OpenAIRE

山本, 直人; Yamamoto, Naoto

1998-01-01

The purpose of this paper is to report radiocarbon age for charred carbonaceous residue on the surface of deep bowls in the Late and Latest Jomon, which were found in Ishikawa Prefecture. Solid-carbon and Humic-acid ingredients were separated by using NaOH solutions from charred deposits, most likely the food residue of Jomon people, collected from the surface of seventeen pottry fragments. ^C ages have been measured by using a Tandetron accelerator mass spectrometer at Dating and Materials R...

Effect of sewage sludge content on gas quality and solid residues produced by cogasification in an updraft gasifier

Energy Technology Data Exchange (ETDEWEB)

Seggiani, Maurizia, E-mail: m.seggiani@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy); Puccini, Monica, E-mail: m.puccini@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy); Raggio, Giovanni, E-mail: g.raggio@tiscali.it [Italprogetti Engineering SPA, Lungarno Pacinotti, 59/A, 56020 San Romano (Pisa) (Italy); Vitolo, Sandra, E-mail: s.vitolo@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy)

2012-10-15

Highlights: Black-Right-Pointing-Pointer Cogasification of sewage sludge with wood pellets in updraft gasifier was analysed. Black-Right-Pointing-Pointer The effects of sewage sludge content on the gasification process were examined. Black-Right-Pointing-Pointer Sewage sludge addition up to 30 wt.% reduces moderately the process performance. Black-Right-Pointing-Pointer At high sewage sludge content slagging and clinker formation occurred. Black-Right-Pointing-Pointer Solid residues produced resulted acceptable at landfills for non-hazardous waste. - Abstract: In the present work, the gasification with air of dehydrated sewage sludge (SS) with 20 wt.% moisture mixed with conventional woody biomass was investigated using a pilot fixed-bed updraft gasifier. Attention was focused on the effect of the SS content on the gasification performance and on the environmental impact of the process. The results showed that it is possible to co-gasify SS with wood pellets (WPs) in updraft fixed-bed gasification installations. However, at high content of sewage sludge the gasification process can become instable because of the very high ash content and low ash fusion temperatures of SS. At an equivalent ratio of 0.25, compared with wood pellets gasification, the addition of sewage sludge led to a reduction of gas yield in favor of an increase of condensate production with consequent cold gas efficiency decrease. Low concentrations of dioxins/furans and PAHs were measured in the gas produced by SS gasification, well below the limiting values for the exhaust gaseous emissions. NH{sub 3}, HCl and HF contents were very low because most of these compounds were retained in the wet scrubber systems. On the other hand, high H{sub 2}S levels were measured due to high sulfur content of SS. Heavy metals supplied with the feedstocks were mostly retained in gasification solid residues. The leachability tests performed according to European regulations showed that metals leachability was

Ore-forming environment and ore-forming system of carbonaceous-siliceous-pelitic rock type uranium deposit in China

International Nuclear Information System (INIS)

Qi Fucheng; Zhang Zilong; Li Zhixing; He Zhongbo; Wang Wenquan

2012-01-01

It is proposed that there are four types of ore-forming systems about carbonaceous-siliceous-pelitic rock type uranium deposit in China based on systematic study on structural environment and distribution regularity of uraniferous construction of marine carbonaceous-siliceous-pelitic rock in China: continental margin rift valley ore-forming systems, continental margin rifting deep fracture zone ore-forming systems, landmass boundary borderland basin ore-forming systems and epicontinental mobile belt downfaulted aulacogen ore-forming systems. It is propounded definitely that it is controlled by margin rift valley ore-forming systems and continental margin rifting deep fracture zone ore-forming systems for large-scale uranium mineralization of carbonaceous-siliceous-pelitic rock type uranium deposit in China, which is also controlled by uraniferous marine carbonaceous-siliceous-pelitic rock construction made up of silicalite, siliceous phosphorite and carbonaceous-siliceous-pelitic rock, which settled down accompany with submarine backwash and sub marine volcanic eruption in margin rift valley and continental margin rifting mineralizing environment. Continental mar gin rift valley and continental margin rifting thermal sedimentation or exhalation sedimentation is the mechanism of forming large-scale uraniferous marine carbonaceous-siliceous-pelitic rock construction Early Palaeozoic Era in China or large-scale uranium-polymetallic mineralization. (authors)

Effects of chemical functional groups on elemental mercury adsorption on carbonaceous surfaces

Energy Technology Data Exchange (ETDEWEB)

Liu Jing, E-mail: liujing27@mail.hust.edu.cn [State Key Laboratory of Coal Combustion, Huazhong University of Science and Technology, Wuhan 430074 (China); Cheney, Marcos A. [Department of Natural Sciences, University of Maryland Eastern Shore, Princess Anne, MD 21853 (United States); Wu Fan; Li Meng [State Key Laboratory of Coal Combustion, Huazhong University of Science and Technology, Wuhan 430074 (China)

2011-02-15

A systematic theoretical study using density functional theory is performed to provide molecular-level understanding of the effects of chemical functional groups on mercury adsorption on carbonaceous surfaces. The zigzag and armchair edges were used in modeling the carbonaceous surfaces to simulate different adsorption sites. The edge atoms on the upper side of the models are unsaturated to simulate active sites. All calculations (optimizations, energies, and frequencies) were made at B3PW91 density functional theory level, using RCEP60VDZ basis set for mercury and 6-31G(d) pople basis set for other atoms. The results indicate that the embedding of halogen atom can increase the activity of its neighboring site which in turn increases the adsorption capacity of the carbonaceous surface for Hg{sup 0}. The adsorption belongs to chemisorptions, which is in good agreement with the experimental results. For the effects of oxygen functional groups, lactone, carbonyl and semiquinone favor Hg{sup 0} adsorption because they increase the neighboring site's activity for mercury adsorption. On the contrary, phenol and carboxyl functional groups show a physisorption of Hg{sup 0}, and reduce Hg capture. This result can explain the seemingly conflicting experimental results reported in the literature concerning the influence of oxygen functional groups on mercury adsorption on carbonaceous surface.

Determination of antibiotic residues in southern Baltic Sea sediments using tandem solid-phase extraction and liquid chromatography coupled with tandem mass spectrometry

Directory of Open Access Journals (Sweden)

Grzegorz Siedlewicz

2016-07-01

Full Text Available The main objective of this study was to adapt analytical procedures for determining antibiotic residues in solid and aquatic samples to marine sediments and to investigate the occurrence of 9 sulfonamides, trimethoprim and 2 quinolones in southern Baltic Sea sediments. The analytical procedure was applied to sediment samples characterized as sand and silty sand. The validation results showed that a sensitive and efficient method applying tandem solid-phase extraction (SPE and liquid chromatography coupled with tandem mass spectrometry (LC–MS/MS was obtained. Analytes were determined in the lower ng g−1 range with good accuracy and precision. The proposed analytical procedure was applied to the analysis of 13 sediment samples collected from the Baltic Sea along the Polish coast. Concentrations of antibiotic residues in environmental samples were calculated based on external matrix-matched calibration. Residues of nine out of twelve of the above antibiotics were detected in sediment samples in a concentrations of up to 419.2 ng g−1 d.w. (dry weight. Sulfamethoxazole and sulfachloropyridazine were the most frequently detected compounds (58% of the analyzed samples. The occurrence frequency of trimethoprim was 42% and it was always detected simultaneously with sulfamethoxazole. Preliminary studies on the spatial distribution of the analyzed antibiotics indicate a high level of antibiotics occurring in the Pomeranian Bay and close to the mouths of Polish rivers. The study is the first one to demonstrate the occurrence of antibiotic residues in sediments of the Polish coastal area. The obtained results suggest that sediment can be an important secondary source of antibiotic residues in the marine environment.

Cellulase and xylanase productions by isolated Amazon Bacillus strains using soybean industrial residue based solid-state cultivation

Directory of Open Access Journals (Sweden)

Heck Júlio X.

2002-01-01

Full Text Available In Brazil, a large amount of a fibrous residue is generated as result of soybean (Glycine max protein production. This material, which is rich in hemicellulose and cellulose, can be used in solid state cultivations for the production of valuable metabolites and enzymes. In this work, we studied the bioconversion of this residue by bacteria strains isolated from water and soil collected in the Amazon region. Five strains among 87 isolated bacteria selected for their ability to produce either celullases or xylanases were cultivated on the aforementioned residue. From strain BL62, identified as Bacillus subtilis, it was obtained a preparation showing the highest specific cellulase activity, 1.08 UI/mg protein within 24 hours of growth. Concerning xylanase, the isolate BL53, also identified as Bacillus subtilis, showed the highest specific activity for this enzyme, 5.19 UI/mg protein within 72 hours of cultivation. It has also been observed the production of proteases that were associated with the loss of cellulase and xylanase activities. These results indicated that the selected microorganisms, and the cultivation process, have great biotechnological potential.

Process and device for separating gaseous and solid noxious substances from residues occurring in thermal processes, particularly in the pyrolysis of waste material. Verfahren und Vorrichtung zur Abscheidung von gasfoermigen und festen Schadstoffen aus Rueckstaenden, die bei thermischen Prozessen, insbesondere der Pyrolyse von Abfallstoffen, anfallen

Energy Technology Data Exchange (ETDEWEB)

1981-12-10

The invention concerns a process for separating gaseous and solid noxious substances from residues which occur in a thermal process, particularly the pyrolysis of waste material in the form of crude gas and solid remnants. The purpose of the invention is to create a process and a device of this kind, where it is possible to remove the part containing the noxious substances separately from the remaining solid residue of the thermal process, particularly the residue from pyrolysis, and to deposit it, and also to make it possible to free the crude gas, particularly pyrolysis gas, from gaseous noxious substances. According to the invention the problem is solved by taking the fine solid part of the solid residue together with the crude gas from the solid residue, which is removed from the thermal process as free falling material, to a reaction vessel, where, by adding additives the sold part or the gaseous noxious substances are bound and removed.

Proto-Planetary Disk Chemistry Recorded by D-Rich Organic Radicals in Carbonaceous Chondrites

OpenAIRE

Remusat, Laurent; Robert, François; Meibom, Anders; Mostefaoui, Smail; Delpoux, Olivier; Binet, Laurent; Gourier, Didier; Derenne, Sylvie

2009-01-01

Insoluble organic matter (IOM) in primitive carbonaceous meteorites has preserved its chemical composition and isotopic heterogeneity since the solar system formed ~4.567 billion years ago. We have identified the carrier moieties of isotopically anomalous hydrogen in IOM isolated from the Orgueil carbonaceous chondrite. Data from high spatial resolution, quantitative isotopic NanoSIMS mapping of Orgueil IOM combined with data from electron paramagnetic resonance spectroscopy reveals that orga...

PRODUCTION OF LIPASES IN SOLID-STATE FERMENTATION BY Aspergillus niger F7-02 WITH AGRICULTURAL RESIDUES

Directory of Open Access Journals (Sweden)

Olayinka Quadri Adio

2015-06-01

Full Text Available In this study mould strains screened and molecularly identified as Aspergillus niger F7-02 was used to produced extracellular lipase in Solid State Fermentation (SSF process. Different agricultural residues were combined in different ratios as carbon, nitrogen and elemental sources in the solid culture medium. The optimization of the culture medium was carried out for such parameters as incubation time (24 h - 96 h, inoculum concentration (0.5 – 3.0%, w/v, initial moisture content (40 – 70%, w/v, and initial pH (6 – 8 for maximum yield. The maximum lipase activity of 76.7 U/ml was obtained with a medium containing rice bran (RB, palm kernel cake (PKC, groundnut cake (GNC and starch (S at the ratio of 5:5:3:1 (%w/w with optimum conditions of 60% moisture, 1% inoculum and a pH of 7.0 with an incubation temperature of 30 oC and incubation time of 72 h.

A Mudball Model for the Evolution of Carbonaceous Asteroids

Science.gov (United States)

Travis, B. J.; Bland, P. A.

2018-05-01

We simulation the evolution of carbonaceous chondrite parent bodies from initially unconsolidated aggregations of rock grains and ice crystals. Application of the numerical model MAGHNUM to evolution of CM type planetesimals and Ceres is described.

On radiogenic nature of xenon-X in carbonaceous and LL chondrites

International Nuclear Information System (INIS)

Gerling, Eh.K.

1982-01-01

The nature of Xe-X from the mineral fraction produced during the differential dissolution of carbonaceous and LL chondrites was investigated using literature data on the age of some meteorites and their fractions and quantities of fission 136 Xe contained in them. A graph of lg fission 136 Xe against the age of meteorites was plotted; the decay constant of a hypothetical superheavy nucleus was calculated using the graph and equaled 1x10 - 7 year - 1 . The calculations served as a forcible argument for the radiogenic nature of xenon with 136 and 134 mass in carbonaceous and LL chondrites

Pelletizing of rice straws: A potential solid fuel from agricultural residues

International Nuclear Information System (INIS)

Puad, E.; Wan Asma, I; Shaharuddin, H.; Mahanim, S.; Rafidah, J.

2010-01-01

Full text: Rice straw is the dry stalks of rice plants, after the grain and chaff have been removed. More than 1 million tonnes of rice straw are produced in MADA in the northern region of Peninsular Malaysia annually. Burning in the open air is the common technique of disposal that contribute to air pollution. In this paper, a technique to convert these residues into solid fuel through pelletizing is presented. The pellets are manufactured from rice straw and sawdust in a disc pelletizer. The pellet properties are quite good with good resistance to mechanical disintegration. The pellets have densities between 1000 and 1200 kg/ m 3 . Overall, converting rice straw into pellets has increased its energy and reduced moisture content to a minimum of 8 % and 30 % respectively. The gross calorific value is about 15.6 MJ/ kg which is lower to sawdust pellet. The garnering of knowledge in the pelletization process provides a path to increase the use of this resource. Rice straw pellets can become an important renewable energy source in the future. (author)

Measurements of non-volatile aerosols with a VTDMA and their correlations with carbonaceous aerosols in Guangzhou, China

Science.gov (United States)

Cheung, Heidi H. Y.; Tan, Haobo; Xu, Hanbing; Li, Fei; Wu, Cheng; Yu, Jian Z.; Chan, Chak K.

2016-07-01

Simultaneous measurements of aerosol volatility and carbonaceous matters were conducted at a suburban site in Guangzhou, China, in February and March 2014 using a volatility tandem differential mobility analyzer (VTDMA) and an organic carbon/elemental carbon (OC / EC) analyzer. Low volatility (LV) particles, with a volatility shrink factor (VSF) at 300 °C exceeding 0.9, contributed 5 % of number concentrations of the 40 nm particles and 11-15 % of the 80-300 nm particles. They were composed of non-volatile material externally mixed with volatile material, and therefore did not evaporate significantly at 300 °C. Non-volatile material mixed internally with the volatile material was referred to as medium volatility (MV, 0.4 transported at low altitudes (below 1500 m) for over 40 h before arrival. Further comparison with the diurnal variations in the mass fractions of EC and the non-volatile OC in PM2.5 suggests that the non-volatile residuals may be related to both EC and non-volatile OC in the afternoon, during which the concentration of aged organics increased. A closure analysis of the total mass of LV and MV residuals and the mass of EC or the sum of EC and non-volatile OC was conducted. It suggests that non-volatile OC, in addition to EC, was one of the components of the non-volatile residuals measured by the VTDMA in this study.

Process of treating carbonaceous substances

Energy Technology Data Exchange (ETDEWEB)

1938-12-16

A process is described of removing halogens or halogen compounds (or both) from the products which form when carbonaceous substances are treated thermally in the presence of halogens or halogen compounds, consisting of passing the reaction products at the same temperature with a substance able to fix halogens or acid halides through an apparatus included between the receiver and the heat exchanger, which contains, in a relatively restricted space, internal elements obliquely disposed in relation to the direction of the flow, stretched in this direction and constituted preferably of helicoidal passages.

Template-free synthesis of multifunctional carbonaceous microcone forests

Science.gov (United States)

Wang, Qiang; Yang, Lei; Dai, Bing; Bai, Jie; Yang, Zhenhuai; Guo, Shuai; He, Yurong; Han, Jiecai; Zhu, Jiaqi

2018-01-01

Forests of vertically aligned carbonaceous microcones are fabricated directly on a nickel mesh by microwave-plasma-assisted chemical vapor deposition. The microstructure is formed through a simple one-step process involving self-assembly. The fabricated composite exhibits superhydrophobicity and superoleophilicity as well as low density, owing to which it floats on water and can be used for the in-situ separation of oil from water at the oil/water interface. Furthermore, the composite exhibits pH responsivity, and its water permeability can be varied simply by altering the pH of the aqueous solution. In addition, the composite is suitable for use as an electrode material for supercapacitors owing to its large geometric surface area, porous structure, and superior electrical properties, which allow for fast ion and electron transportation. Thus, this composite consisting of forests of vertically aligned carbonaceous microcones on a nickel mesh is expected to find use in a wide range of fields and applications, including in environmental cleanup, flow switches, and energy storage devices.

Environmental impact of APC residues from municipal solid waste incineration: reuse assessment based on soil and surface water protection criteria.

Science.gov (United States)

Quina, Margarida J; Bordado, João C M; Quinta-Ferreira, Rosa M

2011-01-01

Waste management and environmental protection are mandatory requirements of modern society. In our study, air pollution control (APC) residues from municipal solid waste incinerators (MSWI) were considered as a mixture of fly ash and fine particulate solids collected in scrubbers and fabric filters. These are hazardous wastes and require treatment before landfill. Although there are a number of treatment options, it is highly recommended to find practical applications rather than just dump them in landfill sites. In general, for using a construction material, beyond technical specifications also soil and surface water criteria may be used to ensure environmental protection. The Dutch Building Materials Decree (BMD) is a valuable tool in this respect and it was used to investigate which properties do not meet the threshold criteria so that APC residues can be further used as secondary building material. To this end, some scenarios were evaluated by considering release of inorganic species from unmoulded and moulded applications. The main conclusion is that the high amount of soluble salts makes the APC residues a building material prohibited in any of the conditions tested. In case of moulding materials, the limits of heavy metals are complied, and their use in Category 1 would be allowed. However, also in this case, the soluble salts lead to the classification of "building material not allowed". The treatments with phosphates or silicates are able to solve the problem of heavy metals, but difficulties with the soluble salts are still observed. This analysis suggests that for APC residues to comply with soil and surface water protection criteria to be further used as building material at least a pre-treating for removing soluble salts is absolutely required. Copyright © 2011 Elsevier Ltd. All rights reserved.

Petrographic characterization of the solid products of coal- pitch coprocessing

Energy Technology Data Exchange (ETDEWEB)

Potter, J.; Kybett, B.D.; McDougall, W.J.; Nambudiri, E.M.V.; Rahimi, P.; Price, J.T.

1986-06-01

Petrographic studies were conducted on four solid residues resulting from the hydrogenation process of 1) Forestburg sub- bituminous coal alone, 2) the coal with a non-coking solvent (anthracene oil), 3) pitch (Cold Lake vacuum-bottom deposits), and 4) a mixture of coal and pitch. The purpose was to determine the amounts of coal and pitch-derived solids in the residues. All the residues were produced under identical severe conditions of liquefaction to promote the formation of solids. The coal processed with anthracene oil gives a residue consisting mainly of isotropic huminitic solids. If the coal is hydrogenated under similar conditions but without a solvent, the predominant residual solids are anisotropic semicokes displaying coarse mosaic textures, which form from vitroplast. The residual products from the hydrogenated Cold Lake vacuum- bottom deposits are also dominantly anisotropic semicokes; these display coarse mosaics and flow textures, and form by the growth and coalescence of mesophase spherules. Both coal- and pitch-derived solids are identified in a residue produced by coprocessing the Forestburg coal with the pitch from the Cold Lake vacuum-bottom deposits. It is concluded that the huminite macerals in the coal generate the fine-grained, mosaic-textured semicokes, whereas the pitch produces the coarse mosaics and flow-textured semicokes.

NMR studies of chemical structural variation of insoluble organic matter from different carbonaceous chondrite groups

Science.gov (United States)

Cody, George D.; Alexander, Conel M. O.'D.

2005-02-01

Solid-state 1H and 13C Nuclear Magnetic Resonance (NMR) spectroscopic experiments have been performed on isolated meteoritic Insoluble Organic Matter (IOM) spanning four different carbonaceous chondrite meteorite groups; a CR2 (EET92042), a CI1 (Orgueil), a CM2 (Murchison), and the unique C2 meteorite, Tagish Lake. These solid state NMR experiments reveal considerable variation in bulk organic composition across the different meteorite group's IOM. The fraction of aromatic carbon increases as CR2 meteorite groups. Single pulse (SP) 13C magic angle spinning (MAS) NMR experiments reveal the presence of nanodiamonds with an apparent concentration ranking in the IOM of CR2 IOM of all four meteoritic IOM fractions are highly substituted. Fast spinning SP 1H MAS NMR spectral data combined with other NMR experimental data reveal that the average hydrogen content of sp 3 bonded carbon functional groups is low, requiring a high degree of aliphatic chain branching in each IOM fraction. The variation in chemistry across the meteorite groups is consistent with alteration by low temperature chemical oxidation. It is concluded that such chemistry principally affected the aliphatic moieties whereas the aromatic moieties and nanodiamonds may have been largely unaffected.

Source apportionment of carbonaceous aerosol in southern Sweden

Directory of Open Access Journals (Sweden)

J. Genberg

2011-11-01

Full Text Available A one-year study was performed at the Vavihill background station in southern Sweden to estimate the anthropogenic contribution to the carbonaceous aerosol. Weekly samples of the particulate matter PM₁₀ were collected on quartz filters, and the amounts of organic carbon, elemental carbon, radiocarbon (¹⁴C and levoglucosan were measured. This approach enabled source apportionment of the total carbon in the PM₁₀ fraction using the concentration ratios of the sources. The sources considered in this study were emissions from the combustion of fossil fuels and biomass, as well as biogenic sources. During the summer, the carbonaceous aerosol mass was dominated by compounds of biogenic origin (80%, which are associated with biogenic primary and secondary organic aerosols. During the winter months, biomass combustion (32% and fossil fuel combustion (28% were the main contributors to the carbonaceous aerosol. Elemental carbon concentrations in winter were about twice as large as during summer, and can be attributed to biomass combustion, probably from domestic wood burning. The contribution of fossil fuels to elemental carbon was stable throughout the year, although the fossil contribution to organic carbon increased during the winter. Thus, the organic aerosol originated mainly from natural sources during the summer and from anthropogenic sources during the winter. The result of this source apportionment was compared with results from the EMEP MSC-W chemical transport model. The model and measurements were generally consistent for total atmospheric organic carbon, however, the contribution of the sources varied substantially. E.g. the biomass burning contributions of OC were underestimated by the model by a factor of 2.2 compared to the measurements.

Biofiltration of composting gases using different municipal solid waste-pruning residue composts: monitoring by using an electronic nose.

Science.gov (United States)

López, R; Cabeza, I O; Giráldez, I; Díaz, M J

2011-09-01

The concentration of volatile organic compounds (VOCs) during the composting of kitchen waste and pruning residues, and the abatement of VOCs by different compost biofilters was studied. VOCs removal efficiencies greater than 90% were obtained using composts of municipal solid waste (MSW) or MSW-pruning residue as biofilter material. An electronic nose identified qualitative differences among the biofilter output gases at very low concentrations of VOCs. These differences were related to compost constituents, compost particle size (2-7 or 7-20mm), and a combination of both factors. The total concentration of VOCs determined by a photoionization analyser and inferred from electronic nose data sets were correlated over an ample range of concentrations of VOCs, showing that these techniques could be specially adapted for the monitoring of these processes. Copyright © 2011 Elsevier Ltd. All rights reserved.

Immobilization of pentachlorophenol in soil using carbonaceous material amendments

Energy Technology Data Exchange (ETDEWEB)

Wen Bei [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Shuangqing Road, Haidian District, Beijing 100085 (China)], E-mail: bwen@rcees.ac.cn; Li Ruijuan; Zhang Shuzhen [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Shuangqing Road, Haidian District, Beijing 100085 (China); Shan Xiaoquan [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Shuangqing Road, Haidian District, Beijing 100085 (China)], E-mail: xiaoquan@rcees.ac.cn; Fang Jing; Xiao Ke [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Shuangqing Road, Haidian District, Beijing 100085 (China); Khan, Shahamat U. [Department of Chemistry and Biochemistry, MSN 3E2, George Mason University, 4400 University Drive, Fairfax, VA 22030-4444 (United States)

2009-03-15

In this study, three pentachlorophenol (PCP) laboratory-spiked and one field-contaminated soil were amended with 2.0% char, humic acid (HA) and peat, respectively. The amended soils were aged for either 7 or 250 days. After amendment, CaCl{sub 2} extractability of PCP was significantly decreased. Desorption kinetics indicated that the proposed amendment could lead to a strong binding and slow desorption of PCP in soils. Amendment with char reduced the bioaccumulation factor (BAF) of PCP most significantly for earthworms (Eisenia fetida) in all soils studied. The results of both physicochemical and biological tests suggested that amendment reduced PCP bioavailability quickly and enduringly, implying that carbonaceous material amendment, especially char amendment, was a potentially attractive in situ remediation method for sequestration of PCP in contaminated soil. - Carbonaceous material amendment was a potential in situ remediation method for pentachlorophenol contaminated soil.

Origin and nature of carbonaceous material in the galaxy

Energy Technology Data Exchange (ETDEWEB)

Hoyle, F; Wickramasinghe, N C [University Coll. of South Wales and Monmouthshire, Cardiff (UK)

1977-12-22

It is stated that astronomers generally believe that the carbonaceous material emerging from stars must be in the form of graphite, the most stable condensed form of carbon, and that such emergence must be confined to situations where the C/O ratio exceeds unity, such as in the atmospheres of carbon stars. It is argued here, however, that whilst this state of affairs remains valid for mass flows from stars of sufficiently low surface temperatures, it is not correct for low density flows from stars with colour temperatures approximately > 4,000 K (or for oscillatory stars with colour temperatures that go above 4,000 K for a portion of their cycle). In the latter case it is shown that carbonaceous material comprised mainly of polysaccharides will be able to condense. Implications for the origin of life on the Earth are discussed.

Thermal conversion of municipal solid waste via hydrothermal carbonization: comparison of carbonization products to products from current waste management techniques.

Science.gov (United States)

Lu, Xiaowei; Jordan, Beth; Berge, Nicole D

2012-07-01

Hydrothermal carbonization (HTC) is a novel thermal conversion process that may be a viable means for managing solid waste streams while minimizing greenhouse gas production and producing residual material with intrinsic value. HTC is a wet, relatively low temperature (180-350 °C) thermal conversion process that has been shown to convert biomass to a carbonaceous residue referred to as hydrochar. Results from batch experiments indicate HTC of representative waste materials is feasible, and results in the majority of carbon (45-75% of the initially present carbon) remaining within the hydrochar. Gas production during the batch experiments suggests that longer reaction periods may be desirable to maximize the production of energy-favorable products. If using the hydrochar for applications in which the carbon will remain stored, results suggest that the gaseous products from HTC result in fewer g CO(2)-equivalent emissions than the gases associated with landfilling, composting, and incineration. When considering the use of hydrochar as a solid fuel, more energy can be derived from the hydrochar than from the gases resulting from waste degradation during landfilling and anaerobic digestion, and from incineration of food waste. Carbon emissions resulting from the use of the hydrochar as a fuel source are smaller than those associated with incineration, suggesting HTC may serve as an environmentally beneficial alternative to incineration. The type and extent of environmental benefits derived from HTC will be dependent on hydrochar use/the purpose for HTC (e.g., energy generation or carbon storage). Copyright © 2012 Elsevier Ltd. All rights reserved.

The use of solid phase extraction method for analysis of residues of pesticides used in banana production in Costa Rica

International Nuclear Information System (INIS)

Castillo, L.E.; Ruepert, C.; Alfaro, A.R.; Solis, E.

1999-01-01

Different solid phase extraction devices were tested for the analysis of residues of eleven pesticides used in banana production in Costa Rica. The analysis was performed by using gas chromatograph equipped with NPD and ECD detectors. In general low recoveries and high variation coefficients were found for chlorothalonil, imazalil, terbufos and thiabendazole. For the other pesticides recoveries ranged between 60 and over 100%. (author)

Modeling and analytical simulation of a smouldering carbonaceous ...

African Journals Online (AJOL)

Modeling and analytical simulation of a smouldering carbonaceous rod. A.A. Mohammed, R.O. Olayiwola, M Eseyin, A.A. Wachin. Abstract. Modeling of pyrolysis and combustion in a smouldering fuel bed requires the solution of flow, heat and mass transfer through porous media. This paper presents an analytical method ...

The analysis of creep characteristics of the surrounding rock of the carbonaceous rock tunnel based on Singh-Mitchell model

Science.gov (United States)

Luo, Junhui; Mi, Decai; Ye, Qiongyao; Deng, Shengqiang; Zeng, Fuquan; Zeng, Yongjun

2018-01-01

Carbonaceous rock has the characteristics of easy disintegration, softening, swelling and environmental sensitivity, which belongs to soft surrounding rock, and the deformation during excavation and long-term stability of the surrounding rock of carbonaceous rock tunnel are common problems in the construction of carbonaceous rock tunnel. According to the above, the Monitor and measure the displacement, temperature and osmotic pressure of the surrounding carbonaceous rock of the tunnel of Guangxi Hebai highway. Then it based on the obtaining data to study the creep mechanism of surrounding rock using Singh-Mitchell model and predict the deformation of surrounding rock before the tunnel is operation. The results show that the Singh-Mitchell creep model can effectively analyse and predict the deformation development law of surrounding rock of tunnel without considering temperature and osmotic pressure, it can provide reference for the construction of carbonaceous rock tunnel and the measures to prevent and reinforce it..

Microporous carbonaceous adsorbents for CO2 separation via selective adsorption

KAUST Repository

Zhao, Yunfeng

2015-01-01

Selective adsorption of CO2 has important implications for many energy and environment-related processes, which require the separation of CO2 from other gases (e.g. N2 and CH4) with high uptakes and selectivity. The development of high-performance adsorbents is one of the most promising solutions to the success of these processes. The present review is focused on the state-of-the-art of carbon-based (carbonaceous) adsorbents, covering microporous inorganic carbons and microporous organic polymers, with emphasis on the correlation between their textural and compositional properties and their CO2 adsorption/separation performance. Special attention is given to the most recently developed materials that were not covered in previous reviews. We summarize various effective strategies (N-doping, surface functionalization, extra-framework ions, molecular design, and pore size engineering) for enhancing the CO2 adsorption capacity and selectivity of carbonaceous adsorbents. Our discussion focuses on CO2/N2 separation and CO2/CH4 separation, while including an introduction to the methods and criteria used for evaluating the performance of the adsorbents. Critical issues and challenges regarding the development of high-performance adsorbents as well as some overlooked facts and misconceptions are also discussed, with the aim of providing important insights into the design of novel carbonaceous porous materials for various selective adsorption based applications. This journal is © The Royal Society of Chemistry.

Modelling carbonaceous aerosol from residential solid fuel burning with different assumptions for emissions

Directory of Open Access Journals (Sweden)

R. Ots

2018-04-01

Full Text Available Evidence is accumulating that emissions of primary particulate matter (PM from residential wood and coal combustion in the UK may be underestimated and/or spatially misclassified. In this study, different assumptions for the spatial distribution and total emission of PM from solid fuel (wood and coal burning in the UK were tested using an atmospheric chemical transport model. Modelled concentrations of the PM components were compared with measurements from aerosol mass spectrometers at four sites in central and Greater London (ClearfLo campaign, 2012, as well as with measurements from the UK black carbon network.The two main alternative emission scenarios modelled were Base4x and combRedist. For Base4x, officially reported PM2.5 from the residential and other non-industrial combustion source sector were increased by a factor of four. For the combRedist experiment, half of the baseline emissions from this same source were redistributed by residential population density to simulate the effect of allocating some emissions to the smoke control areas (that are assumed in the national inventory to have no emissions from this source. The Base4x scenario yielded better daily and hourly correlations with measurements than the combRedist scenario for year-long comparisons of the solid fuel organic aerosol (SFOA component at the two London sites. However, the latter scenario better captured mean measured concentrations across all four sites. A third experiment, Redist – all emissions redistributed linearly to population density, is also presented as an indicator of the maximum concentrations an assumption like this could yield.The modelled elemental carbon (EC concentrations derived from the combRedist experiments also compared well with seasonal average concentrations of black carbon observed across the network of UK sites. Together, the two model scenario simulations of SFOA and EC suggest both that residential solid fuel emissions may be higher than

Modelling carbonaceous aerosol from residential solid fuel burning with different assumptions for emissions

Science.gov (United States)

Ots, Riinu; Heal, Mathew R.; Young, Dominique E.; Williams, Leah R.; Allan, James D.; Nemitz, Eiko; Di Marco, Chiara; Detournay, Anais; Xu, Lu; Ng, Nga L.; Coe, Hugh; Herndon, Scott C.; Mackenzie, Ian A.; Green, David C.; Kuenen, Jeroen J. P.; Reis, Stefan; Vieno, Massimo

2018-04-01

Evidence is accumulating that emissions of primary particulate matter (PM) from residential wood and coal combustion in the UK may be underestimated and/or spatially misclassified. In this study, different assumptions for the spatial distribution and total emission of PM from solid fuel (wood and coal) burning in the UK were tested using an atmospheric chemical transport model. Modelled concentrations of the PM components were compared with measurements from aerosol mass spectrometers at four sites in central and Greater London (ClearfLo campaign, 2012), as well as with measurements from the UK black carbon network.The two main alternative emission scenarios modelled were Base4x and combRedist. For Base4x, officially reported PM2.5 from the residential and other non-industrial combustion source sector were increased by a factor of four. For the combRedist experiment, half of the baseline emissions from this same source were redistributed by residential population density to simulate the effect of allocating some emissions to the smoke control areas (that are assumed in the national inventory to have no emissions from this source). The Base4x scenario yielded better daily and hourly correlations with measurements than the combRedist scenario for year-long comparisons of the solid fuel organic aerosol (SFOA) component at the two London sites. However, the latter scenario better captured mean measured concentrations across all four sites. A third experiment, Redist - all emissions redistributed linearly to population density, is also presented as an indicator of the maximum concentrations an assumption like this could yield.The modelled elemental carbon (EC) concentrations derived from the combRedist experiments also compared well with seasonal average concentrations of black carbon observed across the network of UK sites. Together, the two model scenario simulations of SFOA and EC suggest both that residential solid fuel emissions may be higher than inventory

Characteristics and sources of carbonaceous aerosols from Shanghai, China

Science.gov (United States)

Cao, J.-J.; Zhu, C.-S.; Tie, X.-X.; Geng, F.-H.; Xu, H.-M.; Ho, S. S. H.; Wang, G.-H.; Han, Y.-M.; Ho, K.-F.

2013-01-01

An intensive investigation of carbonaceous PM2.5 and TSP (total suspended particles) from Pudong (China) was conducted as part of the MIRAGE-Shanghai (Megacities Impact on Regional and Global Environment) experiment in 2009. Data for organic and elemental carbon (OC and EC), organic species, including C17 to C40 n-alkanes and 17 polycyclic aromatic hydrocarbons (PAHs), and stable carbon isotopes OC (δ13COC) and EC (δ13CEC) were used to evaluate the aerosols' temporal variations and identify presumptive sources. High OC/EC ratios indicated a large fraction of secondary organic aerosol (SOA); high char/soot ratios indicated stronger contributions to EC from motor vehicles and coal combustion than biomass burning. Diagnostic ratios of PAHs indicated that much of the SOA was produced via coal combustion. Isotope abundances (δ13COC = -24.5 ± 0.8‰ and δ13CEC = -25.1 ± 0.6‰) indicated that fossil fuels were the most important source for carbonaceous PM2.5 (particulate matter less than 2.5 micrometers in diameter), with lesser impacts from biomass burning and natural sources. An EC tracer system and isotope mass balance calculations showed that the relative contributions to total carbon from coal combustion, motor vehicle exhaust, and SOA were 41%, 21%, and 31%; other primary sources such as marine, soil and biogenic emissions contributed 7%. Combined analyses of OC and EC, n-alkanes and PAHs, and stable carbon isotopes provide a new way to apportion the sources of carbonaceous particles.

Energy use and carbon footprints differ dramatically for diverse wastewater-derived carbonaceous substrates: An integrated exploration of biokinetics and life-cycle assessment.

Science.gov (United States)

Li, Yanbo; Wang, Xu; Butler, David; Liu, Junxin; Qu, Jiuhui

2017-03-21

Energy neutrality and reduction of carbon emissions are significant challenges to the enhanced sustainability of wastewater treatment plants (WWTPs). Harvesting energy from wastewater carbonaceous substrates can offset energy demands and enable net power generation; yet, there is limited research about how carbonaceous substrates influence energy and carbon implications of WWTPs with integrated energy recovery at systems-level. Consequently, this research uses biokinetics modelling and life cycle assessment philology to explore this notion, by tracing and assessing the quantitative flows of energy embodied or captured, and by exploring the carbon footprint throughout an energy-intensive activated sludge process with integrated energy recovery facilities. The results indicate that energy use and carbon footprint per cubic meter of wastewater treated, varies markedly with the carbon substrate. Compared with systems driven with proteins, carbohydrates or other short-chain fatty acids, systems fed with acetic acid realized energy neutrality with maximal net gain of power from methane combustion (0.198 kWh) and incineration of residual biosolids (0.153 kWh); and also achieved a negative carbon footprint (72.6 g CO 2 ). The findings from this work help us to better understand and develop new technical schemes for improving the energy efficiency of WWTPs by repurposing the stream of carbon substrates across systems.

Irradiated Benzene Ice Provides Clues to Meteoritic Organic Chemistry

Science.gov (United States)

Callahan, Michael Patrick; Gerakines, Perry Alexander; Martin, Mildred G.; Hudson, Reggie L.; Peeters, Zan

2013-01-01

Aromatic hydrocarbons account for a significant portion of the organic matter in carbonaceous chondrite meteorites, as a component of both the low molecular weight, solvent-extractable compounds and the insoluble organic macromolecular material. Previous work has suggested that the aromatic compounds in carbonaceous chondrites may have originated in the radiation-processed icy mantles of interstellar dust grains. Here we report new studies of the organic residue made from benzene irradiated at 19 K by 0.8 MeV protons. Polyphenyls with up to four rings were unambiguously identified in the residue by gas chromatography-mass spectrometry. Atmospheric pressure photoionization Fourier transform mass spectrometry was used to determine molecular composition, and accurate mass measurements suggested the presence of polyphenyls, partially hydrogenated polyphenyls, and other complex aromatic compounds. The profile of low molecular weight compounds in the residue compared well with extracts from the Murchison and Orgueil meteorites. These results are consistent with the possibility that solid phase radiation chemistry of benzene produced some of the complex aromatics found in meteorites.

Environmental impact of APC residues from municipal solid waste incineration: Reuse assessment based on soil and surface water protection criteria

International Nuclear Information System (INIS)

Quina, Margarida J.; Bordado, Joao C.M.; Quinta-Ferreira, Rosa M.

2011-01-01

Highlights: → The Dutch Building Material Decree (BMD) was used to APC residues from MSWI. → BMD is a straightforward tool to calculate expectable loads to the environment of common pollutants. → Chloride load to the environment lead to classification of building material not allowed. → At least a pre-treatment (e.g. washing) is required in order to remove soluble salts. → The stabilization with phosphates or silicates eliminate the problem of heavy metals. - Abstract: Waste management and environmental protection are mandatory requirements of modern society. In our study, air pollution control (APC) residues from municipal solid waste incinerators (MSWI) were considered as a mixture of fly ash and fine particulate solids collected in scrubbers and fabric filters. These are hazardous wastes and require treatment before landfill. Although there are a number of treatment options, it is highly recommended to find practical applications rather than just dump them in landfill sites. In general, for using a construction material, beyond technical specifications also soil and surface water criteria may be used to ensure environmental protection. The Dutch Building Materials Decree (BMD) is a valuable tool in this respect and it was used to investigate which properties do not meet the threshold criteria so that APC residues can be further used as secondary building material. To this end, some scenarios were evaluated by considering release of inorganic species from unmoulded and moulded applications. The main conclusion is that the high amount of soluble salts makes the APC residues a building material prohibited in any of the conditions tested. In case of moulding materials, the limits of heavy metals are complied, and their use in Category 1 would be allowed. However, also in this case, the soluble salts lead to the classification of 'building material not allowed'. The treatments with phosphates or silicates are able to solve the problem of heavy metals, but

Environmental impacts of residual Municipal Solid Waste incineration: A comparison of 110 French incinerators using a life cycle approach

Energy Technology Data Exchange (ETDEWEB)

Beylot, Antoine, E-mail: a.beylot@brgm.fr; Villeneuve, Jacques

2013-12-15

Highlights: • 110 French incinerators are compared with LCA based on plant-specific data. • Environmental impacts vary as a function of plants energy recovery and NO{sub x} emissions. • E.g. climate change impact ranges from −58 to 408 kg CO{sub 2}-eq/tonne of residual MSW. • Implications for LCA of waste management in a decision-making process are detailed. - Abstract: Incineration is the main option for residual Municipal Solid Waste treatment in France. This study compares the environmental performances of 110 French incinerators (i.e. 85% of the total number of plants currently in activity in France) in a Life Cycle Assessment perspective, considering 5 non-toxic impact categories: climate change, photochemical oxidant formation, particulate matter formation, terrestrial acidification and marine eutrophication. Mean, median and lower/upper impact potentials are determined considering the incineration of 1 tonne of French residual Municipal Solid Waste. The results highlight the relatively large variability of the impact potentials as a function of the plant technical performances. In particular, the climate change impact potential of the incineration of 1 tonne of waste ranges from a benefit of −58 kg CO{sub 2}-eq to a relatively large burden of 408 kg CO{sub 2}-eq, with 294 kg CO{sub 2}-eq as the average impact. Two main plant-specific parameters drive the impact potentials regarding the 5 non-toxic impact categories under study: the energy recovery and delivery rate and the NO{sub x} process-specific emissions. The variability of the impact potentials as a function of incinerator characteristics therefore calls for the use of site-specific data when required by the LCA goal and scope definition phase, in particular when the study focuses on a specific incinerator or on a local waste management plan, and when these data are available.

Environmental impacts of residual Municipal Solid Waste incineration: A comparison of 110 French incinerators using a life cycle approach

International Nuclear Information System (INIS)

Beylot, Antoine; Villeneuve, Jacques

2013-01-01

Highlights: • 110 French incinerators are compared with LCA based on plant-specific data. • Environmental impacts vary as a function of plants energy recovery and NO x emissions. • E.g. climate change impact ranges from −58 to 408 kg CO 2 -eq/tonne of residual MSW. • Implications for LCA of waste management in a decision-making process are detailed. - Abstract: Incineration is the main option for residual Municipal Solid Waste treatment in France. This study compares the environmental performances of 110 French incinerators (i.e. 85% of the total number of plants currently in activity in France) in a Life Cycle Assessment perspective, considering 5 non-toxic impact categories: climate change, photochemical oxidant formation, particulate matter formation, terrestrial acidification and marine eutrophication. Mean, median and lower/upper impact potentials are determined considering the incineration of 1 tonne of French residual Municipal Solid Waste. The results highlight the relatively large variability of the impact potentials as a function of the plant technical performances. In particular, the climate change impact potential of the incineration of 1 tonne of waste ranges from a benefit of −58 kg CO 2 -eq to a relatively large burden of 408 kg CO 2 -eq, with 294 kg CO 2 -eq as the average impact. Two main plant-specific parameters drive the impact potentials regarding the 5 non-toxic impact categories under study: the energy recovery and delivery rate and the NO x process-specific emissions. The variability of the impact potentials as a function of incinerator characteristics therefore calls for the use of site-specific data when required by the LCA goal and scope definition phase, in particular when the study focuses on a specific incinerator or on a local waste management plan, and when these data are available

A rapid, solid phase extraction (SPE technique for the extraction and gas chromatographic determination lindane pesticide residue in tissue and milk

Directory of Open Access Journals (Sweden)

Yuningsih

2006-03-01

Full Text Available Organochlorine pesticide contamination in feed can cause residue in animal product (tissue and milk, so its become a problem in food safety. Solid phase extraction (SPE has been carried out for determination organochlorine pesticide residues in food animal production. The technique was rapid, not costly and produce limited amount of hazardous-waste. Samples were homogenized with acetonitrile trough cartridge C18, eluted in fluorocyl column with 2% ether-petroleum or acetonitrile fortissue and milk samples respectively. The recoveries of tissue sample by addition lindane standard solution: 0.50 and 1.00 μg are 85.10 and 103.10% respectively, while that of milk with the addition of 0.50, 1.00 and 1.50 μg are 83.80, 88.69 and 91.24% respectively. Three replicates were carried out for every sample. According of validation criteria of FAO/IAEA the recovery for analysis of pesticide residues was 70-110%. Therefore, the method is applicable.

Fluidised-bed combustion of gasification residue

Energy Technology Data Exchange (ETDEWEB)

Korpela, T.; Kudjoi, A.; Hippinen, I.; Heinolainen, A.; Suominen, M.; Lu Yong [Helsinki Univ. of Technology (Finland). Lab of Energy Economics and Power Plant Engineering

1996-12-01

Partial gasification processes have been presented as possibilities for future power production. In the processes, the solid materials removed from a gasifier (i.e. fly ash and bed material) contain unburnt fuel and the fuel conversion is increased by burning this gasification residue either in an atmospheric or a pressurised fluidised-bed. In this project, which is a part of European JOULE 2 EXTENSION research programme, the main research objectives are the behaviour of calcium and sulphur compounds in solids and the emissions of sulphur dioxide and nitrogen oxides (NO{sub x} and N{sub 2}O) in pressurised fluidised-bed combustion of gasification residues. (author)

Carbonaceous aerosols from prescribed burning of a boreal forest ecosystem

International Nuclear Information System (INIS)

Mazurek, M.A.; Cofer, W.R. III; Levine, J.S.

1990-10-01

The identity and ambient mass concentrations of radiatively important carbonaceous aerosols were measured for a boreal forest prescribed burn conducted in northern Ontario, CAN in August 1989. Nonsize-segregated airborne particles were collected for smoldering-fire and full-fire conditions using a helicopter sampling platform. Total carbon (TC), organic carbon (OC) and elemental carbon (EC) were measured. Smoke plume mass concentrations of the OC and EC particles were greatest for full-fire conditions and had ranges of 1.560 to 2.160 mg/m -1 (OC) and 0.120 to 0.160 mg/m -3 (EC) with OC:EC ratios of 10 to 18, respectively. Smoldering fire conditions showed smoke plume OC and EC levels of 0.570--1.030 mg/m -3 (OC) and 0.006--0.050 mg/m -3 (EC) and much higher ratios of OC:EC (21 to 95). These aerosol data indicate the formation of EC particles is greatest during full-fire combustion of boreal forest material relative to smoldering combustion. However, EC particles comprise a minor fraction of the particulate carbon smoke aerosols for both full-fire and smoldering conditions; the major component of carbonaceous smoke aerosols emitted during the prescribed burn is OC. Overall, the OC and EC in-plume smoke aerosol data show nonuniform production of these particles during various stages of the prescribed burn, and major differences in the type of carbonaceous aerosol that is generated (OC versus EC)

Environmental Accounting Evidence in Organic Solid Residue Treatment Companies

Directory of Open Access Journals (Sweden)

Bruna Batista Padilha

2014-06-01

Full Text Available The growing concern with natural resources and the environment brings out the true dimension of these issues. The awareness of society causes companies to adopt environmentally correct policies and attitudes, so as to contribute with the preservation of the environment. Accounting, as a social science which studies the patrimony and its affectations, has adapted to the need of its users and has started to care about proper presentation and measurement of environmental items, for effective publication to society. With this premise, this study aims to identify and describe the contributions of Environmental Accounting to the process of environmental accounting disclosure of a company, which deals with organic solid residues from agriculture. Using a case study, it has been intended to analyze the production process and to list the environmental items and events that could benefit the company through their disclosure. It was intended, with this study, to highlight the contribution that the environmental accounting may add to the company, with proper measurement and presentation proposals. We have been able to verify that, indeed, there are events of an environmental nature resulting from the production process and also of the investment that it carries out periodically to preserve nature; however, there re faults in the accounting records from an environmental point of view. The application of environmental accounting in the organization allows for a broad view of environmental management and sustainable development adopted by the entity, registering all events that may generate economic and financial changes.

Distilling carbonaceous materials

Energy Technology Data Exchange (ETDEWEB)

Garrow, J R

1921-04-16

To obtain an increased yield of by-products such as oils, ammonia, and gas from coal, oil shale, wood, peat, and the like by low and medium temperature processes, the requisite quantity of hot producer gas from a gas producer, is caused to travel, without ignition, through the material as it passes in a continuous manner through the retort so that the sensible heat of the producer gas is utilized to produce distillation of the carbonaceous material, the gases passing to a condenser, absorption apparatus, and an ammonia absorber respectively. In a two-stage method of treatment of materials such as peat or the like, separate supplies of producer gas are utilized for a preliminary drying operation and for the distillation of the material, the drying receptacle and the retort being joined together to render the process continuous. The gas from the drying receptacle may be mixed with the combined producer and retort gas from the retort, after the hydrocarbon oils have deen removed therefrom.

Evolution of carbonaceous chondrite parent bodies: Insights into cometary nuclei

International Nuclear Information System (INIS)

McSween, H.Y. Jr.

1989-01-01

It is thought that cometary samples will comprise the most primitive materials that are able to be sampled. Although parent body alteration of such samples would not necessarily detract from scientists' interest in them, the possibility exists that modification processes may have affected cometary nuclei. Inferences about the kinds of modifications that might be encountered can be drawn from data on the evolution of carbonaceous chondrite parent bodies. Observations suggest that, of all the classes of chondrites, these meteorites are most applicable to the study of comets. If the proportion of possible internal heat sources such as Al-26 in cometary materials are similar to those in chondrites, and if the time scale of comet accretion was fast enough to permit incorporation of live radionuclides, comets might have had early thermal histories somewhat like those of carbonaceous chondrite parent bodies

Antarctic carbonaceous chondrites - New opportunities for research

Science.gov (United States)

McSween, Harry Y., Jr.

An account is given of the types of carbonaceous meteorites available in the Antarctic collections of the U.S. and Japan. In the case of the collection for Victoria Land and Queen Maud Land, all known classes for meteorites except C1 are present; available pairing data, though limited, are indicative of the presence of many different falls. Thus far, attention has been focused on the largest meteorites. Most samples, however, are small.

Everyone Wins: A Mars-Impact Origin for Carbonaceous Phobos and Deimos

Science.gov (United States)

Fries, M.; Welzenbach, L.; Steele, A.

2016-01-01

Discussions of Phobos' and Deimos' origin(s) tend to feature an orthogonally opposed pair of observations: dynamical studies which favor coalescence of the moons from an orbital debris ring arising from a large impact on Mars; and reflectance spectroscopy of the moons that indicate a carbonaceous composition that is not consistent with Martian surface materials. One way to reconcile this discrepancy is to consider the option of a Mars-impact origin for Phobos and Deimos, followed by surficial decoration of carbon-rich materials by interplanetary dust particles (IDP). The moons experience a high IDP flux because of their location in Mars' gravity well. Calculations show that accreted carbon is sufficient to produce a surface with reflectance spectra resembling carbonaceous chondrites.

Solid-Phase Extraction and Large-Volume Sample Stacking-Capillary Electrophoresis for Determination of Tetracycline Residues in Milk

Directory of Open Access Journals (Sweden)

Gabriela Islas

2018-01-01

Full Text Available Solid-phase extraction in combination with large-volume sample stacking-capillary electrophoresis (SPE-LVSS-CE was applied to measure chlortetracycline, doxycycline, oxytetracycline, and tetracycline in milk samples. Under optimal conditions, the proposed method had a linear range of 29 to 200 µg·L−1, with limits of detection ranging from 18.6 to 23.8 µg·L−1 with inter- and intraday repeatabilities < 10% (as a relative standard deviation in all cases. The enrichment factors obtained were from 50.33 to 70.85 for all the TCs compared with a conventional capillary zone electrophoresis (CZE. This method is adequate to analyze tetracyclines below the most restrictive established maximum residue limits. The proposed method was employed in the analysis of 15 milk samples from different brands. Two of the tested samples were positive for the presence of oxytetracycline with concentrations of 95 and 126 µg·L−1. SPE-LVSS-CE is a robust, easy, and efficient strategy for online preconcentration of tetracycline residues in complex matrices.

Electrodialytic remediation of air pollution control residues

DEFF Research Database (Denmark)

Jensen, Pernille Erland

Air pollution control (APC) residue from municipal solid waste incineration (MSWI) consists of the fly ash, and, in dry and semi-dry systems, also the reaction products from the flue gas cleaning process. APC residue is considered a hazardous waste due to its high alkalinity, high content of salt...

Sub-micrometer refractory carbonaceous particles in the polar stratosphere

Science.gov (United States)

Schütze, Katharina; Wilson, James Charles; Weinbruch, Stephan; Benker, Nathalie; Ebert, Martin; Günther, Gebhard; Weigel, Ralf; Borrmann, Stephan

2017-10-01

Eleven particle samples collected in the polar stratosphere during SOLVE (SAGE III Ozone loss and validation experiment) from January until March 2000 were characterized in detail by high-resolution transmission and scanning electron microscopy (TEM/SEM) combined with energy-dispersive X-ray microanalysis. A total of 4202 particles (TEM = 3872; SEM = 330) were analyzed from these samples, which were collected mostly inside the polar vortex in the altitude range between 17.3 and 19.9 km. Particles that were volatile in the microscope beams contained ammonium sulfates and hydrogen sulfates and dominated the samples. Some particles with diameters ranging from 20 to 830 nm were refractory in the electron beams. Carbonaceous particles containing additional elements to C and O comprised from 72 to 100 % of the refractory particles. The rest were internal mixtures of these materials with sulfates. The median number mixing ratio of the refractory particles, expressed in units of particles per milligram of air, was 1.1 (mg air)-1 and varied between 0.65 and 2.3 (mg air)-1. Most of the refractory carbonaceous particles are completely amorphous, a few of the particles are partly ordered with a graphene sheet separation distance of 0.37 ± 0.06 nm (mean value ± standard deviation). Carbon and oxygen are the only detected major elements with an atomic O/C ratio of 0.11 ± 0.07. Minor elements observed include Si, S, Fe, Cr and Ni with the following atomic ratios relative to C: Si/C: 0.010 ± 0.011; S/C: 0.0007 ± 0.0015; Fe/C: 0.0052 ± 0.0074; Cr/C: 0.0012 ± 0.0017; Ni/C: 0.0006 ± 0.0011 (all mean values ± standard deviation).High-resolution element distribution images reveal that the minor elements are distributed within the carbonaceous matrix; i.e., heterogeneous inclusions are not observed. No difference in size, nanostructure and elemental composition was found between particles collected inside and outside the polar vortex. Based on chemistry and nanostructure

Impact of anthropogenic emissions and open biomass burning on regional carbonaceous aerosols in South China

Energy Technology Data Exchange (ETDEWEB)

Zhang Gan, E-mail: zhanggan@gig.ac.c [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Li Jun [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Li Xiangdong [Department of Civil and Structural Engineering, Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Xu Yue; Guo Lingli [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Tang Jianhui [Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai 264003 (China); Lee, Celine S.L. [Department of Civil and Structural Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Liu Xiang [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Chen Yingjun [Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai 264003 (China)

2010-11-15

Carbonaceous aerosols were studied at three background sites in south and southwest China. Hok Tsui in Hong Kong had the highest concentrations of carbonaceous aerosols (OC = 8.7 {+-} 4.5 {mu}g/m{sup 3}, EC = 2.5 {+-} 1.9 {mu}g/m{sup 3}) among the three sites, and Jianfeng Mountains in Hainan Island (OC = 5.8 {+-} 2.6 {mu}g/m{sup 3}, EC = 0.8 {+-} 0.4 {mu}g/m{sup 3}) and Tengchong mountain over the east edge of the Tibetan Plateau (OC = 4.8 {+-} 4.0 {mu}g/m{sup 3}, EC = 0.5 {+-} 0.4 {mu}g/m{sup 3}) showed similar concentration levels. Distinct seasonal patterns with higher concentrations during the winter, and lower concentrations during the summertime were observed, which may be caused by the changes of the regional emissions, and monsoon effects. The industrial and vehicular emissions in East, Southeast and South China, and the regional open biomass burning in the Indo-Myanmar region of Asia were probably the two major potential sources for carbonaceous matters in this region. - Anthropogenic emissions in China and open biomass burning in the Indo-Myanmar region were the two major potential sources for carbonaceous matters in South China region.

Impact of anthropogenic emissions and open biomass burning on regional carbonaceous aerosols in South China

International Nuclear Information System (INIS)

Zhang Gan; Li Jun; Li Xiangdong; Xu Yue; Guo Lingli; Tang Jianhui; Lee, Celine S.L.; Liu Xiang; Chen Yingjun

2010-01-01

Carbonaceous aerosols were studied at three background sites in south and southwest China. Hok Tsui in Hong Kong had the highest concentrations of carbonaceous aerosols (OC = 8.7 ± 4.5 μg/m 3 , EC = 2.5 ± 1.9 μg/m 3 ) among the three sites, and Jianfeng Mountains in Hainan Island (OC = 5.8 ± 2.6 μg/m 3 , EC = 0.8 ± 0.4 μg/m 3 ) and Tengchong mountain over the east edge of the Tibetan Plateau (OC = 4.8 ± 4.0 μg/m 3 , EC = 0.5 ± 0.4 μg/m 3 ) showed similar concentration levels. Distinct seasonal patterns with higher concentrations during the winter, and lower concentrations during the summertime were observed, which may be caused by the changes of the regional emissions, and monsoon effects. The industrial and vehicular emissions in East, Southeast and South China, and the regional open biomass burning in the Indo-Myanmar region of Asia were probably the two major potential sources for carbonaceous matters in this region. - Anthropogenic emissions in China and open biomass burning in the Indo-Myanmar region were the two major potential sources for carbonaceous matters in South China region.

Sorption of ionizable and ionic organic compounds to biochar, activated carbon and other carbonaceous materials.

Science.gov (United States)

Kah, Melanie; Sigmund, Gabriel; Xiao, Feng; Hofmann, Thilo

2017-11-01

The sorption of ionic and ionizable organic compounds (IOCs) (e.g., pharmaceuticals and pesticides) on carbonaceous materials plays an important role in governing the fate, transport and bioavailability of IOCs. The paradigms previously established for the sorption of neutral organic compounds do not always apply to IOCs and the importance of accounting for the particular sorption behavior of IOCs is being increasingly recognized. This review presents the current state of knowledge and summarizes the recent advances on the sorption of IOCs to carbonaceous sorbents. A broad range of sorbents were considered to evaluate the possibility to read across between fields of research that are often considered in isolation (e.g., carbon nanotubes, graphene, biochar, and activated carbon). Mechanisms relevant to IOCs sorption on carbonaceous sorbents are discussed and critically evaluated, with special attention being given to emerging sorption mechanisms including low-barrier, charge-assisted hydrogen bonds and cation-π assisted π-π interactions. The key role played by some environmental factors is also discussed, with a particular focus on pH and ionic strength. Overall the review reveals significant advances in our understanding of the interactions between IOCs and carbonaceous sorbents. In addition, knowledge gaps are identified and priorities for future research are suggested. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Effect of Carbonaceous Reductant Selection on Chromite Pre-reduction

Science.gov (United States)

Kleynhans, E. L. J.; Beukes, J. P.; Van Zyl, P. G.; Bunt, J. R.; Nkosi, N. S. B.; Venter, M.

2017-04-01

Ferrochrome (FeCr) production is an energy-intensive process. Currently, the pelletized chromite pre-reduction process, also referred to as solid-state reduction of chromite, is most likely the FeCr production process with the lowest specific electricity consumption, i.e., MWh/t FeCr produced. In this study, the effects of carbonaceous reductant selection on chromite pre-reduction and cured pellet strength were investigated. Multiple linear regression analysis was employed to evaluate the effect of reductant characteristics on the aforementioned two parameters. This yielded mathematical solutions that can be used by FeCr producers to select reductants more optimally in future. Additionally, the results indicated that hydrogen (H)- (24 pct) and volatile content (45.8 pct) were the most significant contributors for predicting variance in pre-reduction and compressive strength, respectively. The role of H within this context is postulated to be linked to the ability of a reductant to release H that can induce reduction. Therefore, contrary to the current operational selection criteria, the authors believe that thermally untreated reductants ( e.g., anthracite, as opposed to coke or char), with volatile contents close to the currently applied specification (to ensure pellet strength), would be optimal, since it would maximize H content that would enhance pre-reduction.

Feasibility of biogas production from anaerobic co-digestion of herbal-extraction residues with swine manure.

Science.gov (United States)

Li, Yan; Yan, Xi-Luan; Fan, Jie-Ping; Zhu, Jian-Hang; Zhou, Wen-Bin

2011-06-01

The objective of this work was to examine the feasibility of biogas production from the anaerobic co-digestion of herbal-extraction residues with swine manure. Batch and semi-continuous experiments were carried out under mesophilic anaerobic conditions. Batch experiments revealed that the highest specific biogas yield was 294 mL CH(4) g(-1) volatile solids added, obtained at 50% of herbal-extraction residues and 3.50 g volatile solids g(-1) mixed liquor suspended solids. Specific methane yield from swine manure alone was 207 mL CH(4) g(-1) volatile solid added d(-1) at 3.50 g volatile solids g(-1) mixed liquor suspended solids. Furthermore, specific methane yields were 162, 180 and 220 mL CH(4) g (-1) volatile solids added d(-1) for the reactors co-digesting mixtures with 10%, 25% and 50% herbal-extraction residues, respectively. These results suggested that biogas production could be enhanced efficiently by the anaerobic co-digestion of herbal-extraction residues with swine manure. Copyright © 2011 Elsevier Ltd. All rights reserved.

Molecular and isotope constraints on the formation of the insoluble organic matter of carbonaceous meteorites

Science.gov (United States)

Derenne, Sylvie; Robert, François

2017-04-01

The origin of the insoluble organic matter (IOM) of the carbonaceous meteorites remains an unsolved issue despite major achievements in the knowledge of its chemical structure. The latter led us to propose a model for its molecular structure. Based on the relationship between the aromatic moieties of the macromolecular structure and their aliphatic linkages, it was recently suggested that, its synthesis has taken place in the gas phase of the disk surrounding the Sun in its early T-Tauri phase and that organic radicals have played a central role in this organo-synthesis. To test experimentally this pathway, we submitted short hydrocarbons (methane, pentane, octane) to a microwave plasma discharge so as to produce in situ CHx radicals. The black organic residue deposited contained both soluble and insoluble OM. The comparison at the molecular level between the thus synthesized IOM and that of meteorite led to strong similarities thus supporting the proposed pathway for its organo-synthesis. Moreover, in the meteorite IOM, systematic deuterium enrichment relative to the protosolar value is observed at the bulk sample scale and micrometer-sized grains exhibit dramatic enrichments in deuterium interpreted as a heritage of the interstellar medium or resulting from ion-molecule reactions taking place in the diffuse part of the solar disk. In the aforementioned synthesized IOM, NanoSIMS analyses revealed large variations at a sub-micrometric spatial resolution. They likely reflect the differences in the D/H ratios of the CHx radicals whose polymerization is at the origin of the IOM. These isotopic heterogeneities are commensurable with those observed in meteorite IOM. As a consequence, the appearance of organic radicals in the ionized regions of the T-Tauri solar disk may have triggered the formation of organic compounds. This laboratory synthesis thus shed a new light on the formation conditions and pathways of the IOM of carbonaceous chondrites.

Cementation of secondary wastes generated from carbonisation of spent organic ion exchange resins from nuclear power plants

International Nuclear Information System (INIS)

Sathi Sasidharan, N.; Deshingkar, D.S.; Wattal, P.K.

2004-07-01

The spent IX resins containing radioactive fission and activation products from power reactors are highly active solid wastes generated during operations of nuclear reactors. Process for carbonization of IX resins to achieve weight and volume reduction has been optimized on 50 dm 3 /batch pilot test rig. The process generates carbonaceous residue, organic liquid condensates (predominantly styrene) and aqueous alkaline scrubber solutions as secondary wastes. The report discusses laboratory tests on leaching of 137 Cs from cement matrix incorporating carbonaceous residues and extrapolation of results to 200 liter matrix block. The cumulative fraction of 137 Cs leached from 200 liter cement matrix was estimated to be 0.0021 in 200 days and 0.0418 over a period of 30 years. Incorporation of organic liquid condensates into cement matrix has been tried out successfully. Thus two types of secondary wastes generated during carbonization of spent IX resins can be immobilized in cement matrix. (author)

Assessment of long-term pH developments in leachate from waste incineration residues

DEFF Research Database (Denmark)

Astrup, Thomas; Jakobsen, Rasmus; Christensen, Thomas Højlund

2006-01-01

influenced by changes in pH over time. The paper presents an approach for assessing pH changes in leachate from municipal solid waste incineration (MSWI) air-pollution-control (APC) residues. Residue samples were subjected to a stepwise batch extraction method in order to obtain residue samples at a range...... of pH Values (similar to common pH-dependence tests), and then on these samples to determine leaching of alkalinity as well as remaining solid phase alkalinity. On a range of APC residues covering various pretreatment and disposal options, this procedure was used to determine leachable and residual...... alkalinity as a function of pH. Mass balance calculations for typical disposal scenarios were used to provide data on pH as a function of the liquid-to-solid (L/S) ratio in the leaching system. Regardless of residue type and pretreatment, pH was found to stay above 7 for L/S ratios up to about 2000 L kg(-1...

Headspace Solid Phase Microextraction in Pesticide Residues Analysis: 2. Apple Samples

Directory of Open Access Journals (Sweden)

Jelena Milinović

2007-01-01

Full Text Available Headspace solid phase microextraction method (HS/SPME, optimised previously for pesticide water solutions, was applied to trace residues of the pesticides chlorpyrifos, fenthion and bifenthrin in apple samples. One-hour extraction procedure was performed at 60oC extraction temperature. Nonpolar polydimethyl siloxane (PDMS fiber was used. Detection and quantification were carried out by gas chromatography/mass spectrometry (GC/MS. A non-pesticide treated apple sample was fortified with the pesticides over a 0.025-1.25 mg/kg concentration range in order to determine analytical parameters of the method applied. Linearity with regression coefficient (R values higher than 0.99 were obtained over the whole concentration range investigated for chlorpyrifos and fenthion, while linear dependence was observed in the 0.1-1.25 mg/kg range for bifenthrin. Relative recovery values for samples fortified at different levels were in the 56.68-82.91% range. Limit of detection (LOD values were determined as follows: 0.014 mg/kg for chlorpyrifos, 0.021 mg/kg for fenthion and 0.053 mg/kg for bifenthrin. Relative standard deviation (RSD values obtained for multiple analysis of the sample fortified at 0.6 mg/kg level were not higher than 20%.

Preg-robbing of Gold by Carbonaceous Materials Encountered in ...

African Journals Online (AJOL)

Processing of gold from refractory ores containing carbonaceous materials (CM) poses challenges due to the ability of the CM to preg-rob dissolved gold. Depending on the type and maturity of CM encountered, preg-robbing of aurocyanide ion can lead to reduction in gold recovery ranging from a few percentages to more ...

Carbonaceous particle record in lake sediments from the Arctic and other remote areas of the northern hemisphere

International Nuclear Information System (INIS)

Rose, N.L.

1995-01-01

Lake sediments, including spheroidal carbonaceous particles produced by high temperature combustion of fossil fuels, contain a record of lake, catchment and atmospheric deposition history. The spatial and temporal distributions of these particles can indicate the extent to which a single lake or a region has been contaminated by airborne pollutants (e.g. sulfur, polycyclic aromatic hydrocarbons (PAHs)) derived from fossil fuels. The carbonaceous particle records of two Arctic lakes, Shuonijavr and Stepanovichjarvi, close to local pollution sources on the Kola Peninsula, Russia, are compared with the record of a remote lake on Svalbard and with mid-latitude remote mountain lakes in Europe and Asia. Although, Shuonijavr and Stepanovichjarvi show relatively high levels of contamination, as expected, the presence of carbonaceous particles at all of the remote sites studied suggests there is a hemispherical background of these particles. Other less remote mountain lakes in Europe have been found to contain significant concentrations of particles and these may represent regional deposition patterns. Carbonaceous particle analysis may provide an effective assessment of whether a lake site is receiving local, regional or background levels of deposition

Processes for liquefying carbonaceous feedstocks and related compositions

Energy Technology Data Exchange (ETDEWEB)

MacDonnell, Frederick M.; Dennis, Brian H.; Billo, Richard E.; Priest, John W.

2017-02-28

Methods for the conversion of lignites, subbituminous coals and other carbonaceous feedstocks into synthetic oils, including oils with properties similar to light weight sweet crude oil using a solvent derived from hydrogenating oil produced by pyrolyzing lignite are set forth herein. Such methods may be conducted, for example, under mild operating conditions with a low cost stoichiometric co-reagent and/or a disposable conversion agent.

Environmental impacts of residual municipal solid waste incineration: a comparison of 110 French incinerators using a life cycle approach.

Science.gov (United States)

Beylot, Antoine; Villeneuve, Jacques

2013-12-01

Incineration is the main option for residual Municipal Solid Waste treatment in France. This study compares the environmental performances of 110 French incinerators (i.e., 85% of the total number of plants currently in activity in France) in a Life Cycle Assessment perspective, considering 5 non-toxic impact categories: climate change, photochemical oxidant formation, particulate matter formation, terrestrial acidification and marine eutrophication. Mean, median and lower/upper impact potentials are determined considering the incineration of 1 tonne of French residual Municipal Solid Waste. The results highlight the relatively large variability of the impact potentials as a function of the plant technical performances. In particular, the climate change impact potential of the incineration of 1 tonne of waste ranges from a benefit of -58 kg CO2-eq to a relatively large burden of 408 kg CO2-eq, with 294 kg CO2-eq as the average impact. Two main plant-specific parameters drive the impact potentials regarding the 5 non-toxic impact categories under study: the energy recovery and delivery rate and the NOx process-specific emissions. The variability of the impact potentials as a function of incinerator characteristics therefore calls for the use of site-specific data when required by the LCA goal and scope definition phase, in particular when the study focuses on a specific incinerator or on a local waste management plan, and when these data are available. Copyright © 2013 Elsevier Ltd. All rights reserved.

Pulmonary exposure to carbonaceous nanomaterials and sperm quality.

Science.gov (United States)

Skovmand, Astrid; Jacobsen Lauvås, Anna; Christensen, Preben; Vogel, Ulla; Sørig Hougaard, Karin; Goericke-Pesch, Sandra

2018-01-31

Semen quality parameters are potentially affected by nanomaterials in several ways: Inhaled nanosized particles are potent inducers of pulmonary inflammation, leading to the release of inflammatory mediators. Small amounts of particles may translocate from the lungs into the lung capillaries, enter the systemic circulation and ultimately reach the testes. Both the inflammatory response and the particles may induce oxidative stress which can directly affect spermatogenesis. Furthermore, spermatogenesis may be indirectly affected by changes in the hormonal milieu as systemic inflammation is a potential modulator of endocrine function. The aim of this study was to investigate the effects of pulmonary exposure to carbonaceous nanomaterials on sperm quality parameters in an experimental mouse model. Effects on sperm quality after pulmonary inflammation induced by carbonaceous nanomaterials were investigated by intratracheally instilling sexually mature male NMRI mice with four different carbonaceous nanomaterials dispersed in nanopure water: graphene oxide (18 μg/mouse/i.t.), Flammruss 101, Printex 90 and SRM1650b (0.1 mg/mouse/i.t. each) weekly for seven consecutive weeks. Pulmonary inflammation was determined by differential cell count in bronchoalveolar lavage fluid. Epididymal sperm concentration and motility were measured by computer-assisted sperm analysis. Epididymal sperm viability and morphological abnormalities were assessed manually using Hoechst 33,342/PI flourescent and Spermac staining, respectively. Epididymal sperm were assessed with regard to sperm DNA integrity (damage). Daily sperm production was measured in the testis, and testosterone levels were measured in blood plasma by ELISA. Neutrophil numbers in the bronchoalveolar fluid showed sustained inflammatory response in the nanoparticle-exposed groups one week after the last instillation. No significant changes in epididymal sperm parameters, daily sperm production or plasma testosterone levels

Hydrocarbon oils from carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Fletcher, J

1943-01-28

Carbonaceous material is subjected to gradually increasing temperature in a retort and the gases and vapours are drawn off through four pipes according to their temperature and are passed respectively to a separate bubble tower or a fractionation column. The condensate and overhead from each bubble tower are refluxed in the bubble tower into which the gases and vapours of the next succeeding higher temperature are passed and the condensates and overheads from the bubble tower into which gases and vapours at the highest of the lower temperatures are passed are refluxed in the fractionation column. The waste products of combustion pass to a boiler for generating steam for the fractional plant.

Regional variation of carbonaceous aerosols from space and simulations

Science.gov (United States)

Mukai, Sonoyo; Sano, Itaru; Nakata, Makiko; Kokhanovsky, Alexander

2017-04-01

Satellite remote sensing provides us with a systematic monitoring in a global scale. As such, aerosol observation via satellites is known to be useful and effective. However, before attempting to retrieve aerosol properties from satellite data, the efficient algorithms for aerosol retrieval need to be considered. The characteristics and distributions of atmospheric aerosols are known to be complicated, owing to both natural factors and human activities. It is known that the biomass burning aerosols generated by the large-scale forest fires and burn agriculture have influenced the severity of air pollution. Nevertheless the biomass burning episodes increase due to global warming and climate change and vice versa. It is worth noting that the near ultra violet (NUV) measurements are helpful for the detection of carbonaceous particles, which are the main component of aerosols from biomass burning. In this work, improved retrieval algorithms for biomass burning aerosols are shown by using the measurements observed by GLI and POLDER-2 on Japanese short term mission ADEOS-2 in 2003. The GLI sensor has 380nm channel. For detection of biomass burning episodes, the aerosol optical thickness of carbonaceous aerosols simulated with the numerical model simulations (SPRINTARS) is available as well as fire products from satellite imagery. Moreover the algorithm using shorter wavelength data is available for detection of absorbing aerosols. An algorithm based on the combined use of near-UV and violet data has been introduced in our previous work with ADEOS (Advanced Earth Observing Satellite) -2 /GLI measurements [1]. It is well known that biomass burning plume is a seasonal phenomenon peculiar to a particular region. Hence, the mass concentrations of aerosols are frequently governed with spatial and/or temporal variations of biomass burning plumes. Accordingly the satellite data sets for our present study are adopted from the view points of investigation of regional and seasonal

Electrodialytically treated MSWI APC residue as substitute for cement in mortar

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Geiker, Mette Rica; Jensen, Pernille Erland

2014-01-01

Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are considered hazardous waste and need pretreatment prior to possible reuse. Here, two MSWI APC residues, from which the most mobile fraction of heavy metals and salts has been removed by carbonation and/or elect......Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are considered hazardous waste and need pretreatment prior to possible reuse. Here, two MSWI APC residues, from which the most mobile fraction of heavy metals and salts has been removed by carbonation and....../or electrodialytic remediation, were used in Portland cement mortar. Mortar bars with 15 % weight replacement of cement by APC residues showed compressive strengths up to 40 MPa after 28/32 days. Heavy metal and salt leaching from both crushed and monolithic mortars with APC residues was generally similar...

Hydrogen ion-driven permeation in carbonaceous films

International Nuclear Information System (INIS)

Anderl, R.A.; Holland, D.F.; Longhurst, G.R.

1989-01-01

This paper presents the results of investigations into the permeation properties of amorphous carbonaceous, a-C:H, films produced by plasmachemical deposition techniques. Carbonaceous films on iron substrates with thickness ranging from 60 nm to 110 nm were subjected to high fluence implantations with mass analyzed D 3 + ions with energies ranging from 600 eV to 3000 eV and fluxes ranging from 5x10 14 D/cm 2 s to 5x10 15 D/cm 2 s, respectively. Deuterium re-emission upstream, deuterium permeation downstream and secondary ions sputtered from the implantation surface were measured as a function of implantation fluence for specimens at 420 K. The present studies indicate that the a-C:H film permeability is directly related to the time, hence the fluence, required to achieve isotopic replacement and saturation of the deuterium ion beam atoms stopped in the implant region. Once the deuterium saturation level is achieved in the layer, a significant fraction of the implanting ions can result in permeation. For the present experiment, this permeation factor was much higher than that for uncoated iron specimens subjected to similar beam conditions. Carbon sputter yields of 0.008-0.01 C/D were determined in this work for 1000-eV to 400-eV deuterium ions incident on a-C:H films. (orig.)

Hydrogen ion-driven permeation in carbonaceous films

Energy Technology Data Exchange (ETDEWEB)

Anderl, R.A.; Holland, D.F.; Longhurst, G.R.

1989-04-01

This paper presents the results of investigations into the permeation properties of amorphous carbonaceous, a-C:H, films produced by plasmachemical deposition techniques. Carbonaceous films on iron substrates with thickness ranging from 60 nm to 110 nm were subjected to high fluence implantations with mass analyzed D/sub 3//sup +/ ions with energies ranging from 600 eV to 3000 eV and fluxes ranging from 5x10/sup 14/ D/cm/sup 2/ s to 5x10/sup 15/ D/cm/sup 2/ s, respectively. Deuterium re-emission upstream, deuterium permeation downstream and secondary ions sputtered from the implantation surface were measured as a function of implantation fluence for specimens at 420 K. The present studies indicate that the a-C:H film permeability is directly related to the time, hence the fluence, required to achieve isotopic replacement and saturation of the deuterium ion beam atoms stopped in the implant region. Once the deuterium saturation level is achieved in the layer, a significant fraction of the implanting ions can result in permeation. For the present experiment, this permeation factor was much higher than that for uncoated iron specimens subjected to similar beam conditions. Carbon sputter yields of 0.008-0.01 C/D were determined in this work for 1000-eV to 400-eV deuterium ions incident on a-C:H films. (orig.).

Hydrogen ion-driven permeation in carbonaceous films

Science.gov (United States)

Anderl, R. A.; Holland, D. F.; Longhurst, G. R.

1989-04-01

This paper presents the results of investigations into the permeation properties of amorphous carbonaceous, a-C: H, films produced by plasmachemical deposition techniques. Carbonaceous films on iron substrates with thickness ranging from 60 nm to 110 nm were subjected to high fluence implantations with mass analyzed D +3 ions with energies ranging from 600 eV to 3000 eV and fluxes ranging from 5 × 10 14D/ cm2 s to 5 × 10 15D/ cm2 s, respectively. Deuterium re-emission upstream, deuterium permeation downstream and secondary ions sputtered from the implantation surface were measured as a function of implantation fluence for specimens at 420 K. The present studies indicate that the a-C : H film permeability is directly related to the time, hence the fluence, required to achieve isotopic replacement and saturation of the deuterium ion beam atoms stopped in the implant region. Once the deuterium saturation level is achieved in the layer, a significant fraction of the implanting ions can result in permeation. For the present experiment, this permeation factor was much higher than that for uncoated iron specimens subjected to similar beam conditions. Carbon sputter yields of 0.008-0.01 C/D were determined in this work for 1000-eV to 400-eV deuterium ions incident on a-C : H films.

A dual origin for water in carbonaceous asteroids revealed by CM chondrites

Science.gov (United States)

Piani, Laurette; Yurimoto, Hisayoshi; Remusat, Laurent

2018-04-01

Carbonaceous asteroids represent the principal source of water in the inner Solar System and might correspond to the main contributors for the delivery of water to Earth. Hydrogen isotopes in water-bearing primitive meteorites, for example carbonaceous chondrites, constitute a unique tool for deciphering the sources of water reservoirs at the time of asteroid formation. However, fine-scale isotopic measurements are required to unravel the effects of parent-body processes on the pre-accretion isotopic distributions. Here, we report in situ micrometre-scale analyses of hydrogen isotopes in six CM-type carbonaceous chondrites, revealing a dominant deuterium-poor water component (δD = -350 ± 40‰) mixed with deuterium-rich organic matter. We suggest that this deuterium-poor water corresponds to a ubiquitous water reservoir in the inner protoplanetary disk. A deuterium-rich water signature has been preserved in the least altered part of the Paris chondrite (δDParis ≥ -69 ± 163‰) in hydrated phases possibly present in the CM rock before alteration. The presence of the deuterium-enriched water signature in Paris might indicate that transfers of ice from the outer to the inner Solar System were significant within the first million years of the history of the Solar System.

Characteristics and sources of carbonaceous aerosols from Shanghai, China

Directory of Open Access Journals (Sweden)

J.-J. Cao

2013-01-01

Full Text Available An intensive investigation of carbonaceous PM_2.5 and TSP (total suspended particles from Pudong (China was conducted as part of the MIRAGE-Shanghai (Megacities Impact on Regional and Global Environment experiment in 2009. Data for organic and elemental carbon (OC and EC, organic species, including C17 to C40 n-alkanes and 17 polycyclic aromatic hydrocarbons (PAHs, and stable carbon isotopes OC (δ¹³C_OC and EC (δ¹³C_EC were used to evaluate the aerosols' temporal variations and identify presumptive sources. High OC/EC ratios indicated a large fraction of secondary organic aerosol (SOA; high char/soot ratios indicated stronger contributions to EC from motor vehicles and coal combustion than biomass burning. Diagnostic ratios of PAHs indicated that much of the SOA was produced via coal combustion. Isotope abundances (δ¹³C_OC = −24.5 ± 0.8‰ and δ¹³C_EC = −25.1 ± 0.6‰ indicated that fossil fuels were the most important source for carbonaceous PM_2.5 (particulate matter less than 2.5 micrometers in diameter, with lesser impacts from biomass burning and natural sources. An EC tracer system and isotope mass balance calculations showed that the relative contributions to total carbon from coal combustion, motor vehicle exhaust, and SOA were 41%, 21%, and 31%; other primary sources such as marine, soil and biogenic emissions contributed 7%. Combined analyses of OC and EC, n-alkanes and PAHs, and stable carbon isotopes provide a new way to apportion the sources of carbonaceous particles.

Electrodialytic removal of heavy metals and chloride from municipal solid waste incineration fly ash and air pollution control residue in suspension - test of a new two compartment experimental cell

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Magro, Cátia; Guedes, Paula

2015-01-01

Municipal solid waste incineration (MSWI) residues such as fly ash and air pollution control (APC) residues are classified as hazardous waste and disposed of, although they contain potential resources. The most problematic elements in MSWI residues are leachable heavy metals and salts. For reuse...... of MSWI residues in for instance concrete, the aim of remediation should be reduction of the heavy metal leaching, while at the same time keeping the alkaline pH, so the residue can replace cement. In this study a MSWI residues were subjected to electrodialytic remediation under various experimental...... heavy metal leaching except when the pH was reduced to a level below 8 for the fly ash. On the other hand, Cr leaching increased by the electrodialytic treatment. Cl leaching from the MSWI residues was less dependent on experimental conditions and was reduced in all experiments compared to the initial...

Ethanol and other oxygenateds from low grade carbonaceous resources

Energy Technology Data Exchange (ETDEWEB)

Joo, O.S.; Jung, K.D.; Han, S.H. [Korea Institute of Science and Technology, Seoul (Korea, Democratic People`s Republic of)] [and others

1995-12-31

Anhydrous ethanol and other oxygenates of C2 up can be produced quite competitively from low grade carbonaceous resources in high yield via gasification, methanol synthesis, carbonylation of methanol an hydrogenation consecutively. Gas phase carbonylation of methanol to form methyl acetate is the key step for the whole process. Methyl acetate can be produced very selectively in one step gas phase reaction on a fixed bed column reactor with GHSV over 5,000. The consecutive hydrogenation of methyl or ethyl acetate produce anhydrous ethanol in high purity. It is also attempted to co-produce methanol and DME in IGCC, in which low grade carbonaceous resources are used as energy sources, and the surplus power and pre-power gas can be stored in liquid form of methanol and DME during base load time. Further integration of C2 up oxygenate production with IGCC can improve its economics. The attempt of above extensive technology integration can generate significant industrial profitability as well as reduce the environmental complication related with massive energy consumption.

Thermogravimetric investigation on the degradation properties and combustion performance of bio-oils.

Science.gov (United States)

Ren, Xueyong; Meng, Jiajia; Moore, Andrew M; Chang, Jianmin; Gou, Jinsheng; Park, Sunkyu

2014-01-01

The degradation properties and combustion performance of raw bio-oil, aged bio-oil, and bio-oil from torrefied wood were investigated through thermogravimetric analysis. A three-stage process was observed for the degradation of bio-oils, including devolatilization of the aqueous fraction and light compounds, transition of the heavy faction to solid, and combustion of carbonaceous residues. Pyrolysis kinetics parameters were calculated via the reaction order model and 3D-diffusion model, and combustion indexes were used to qualitatively evaluate the thermal profiles of tested bio-oils for comparison with commercial oils such as fuel oils. It was found that aged bio-oil was more thermally instable and produced more combustion-detrimental carbonaceous solid. Raw bio-oil and bio-oil from torrefied wood had comparable combustion performance to fuel oils. It was considered that bio-oil has a potential to be mixed with or totally replace the fuel oils in boilers. Copyright © 2013 Elsevier Ltd. All rights reserved.

Low-temperature catalytic conversion of carbonaceous materials

Directory of Open Access Journals (Sweden)

Tabakaev Roman B.

2015-01-01

Full Text Available Laws of the rate of carbon conversion in steam atmosphere at a temperature in modes of the catalytic low-temperature treatment of peat, brown coal, semi-coke from peat and brown coal are obtained by experiments. Increasing of the rate of carbon conversion in temperature range up to 500 °C is achieved by using of catalysts. The possibility of using results is associated with the burners, a working zone of which is porous filling from carbonaceous particles.

Nitrogen availability of biogas residues

Energy Technology Data Exchange (ETDEWEB)

El-Sayed Fouda, Sara

2011-09-07

The objectives of this study were to characterize biogas residues either unseparated or separated into a liquid and a solid phase from the fermentation of different substrates with respect to their N and C content. In addition, short and long term effects of the application of these biogas residues on the N availability and N utilization by ryegrass was investigated. It is concluded that unseparated or liquid separated biogas residues provide N at least corresponding to their ammonium content and that after the first fertilizer application the C{sub org}:N{sub org} ratio of the biogas residues was a crucial factor for the N availability. After long term application, the organic N accumulated in the soil leads to an increased release of N.

Functionalization of biomass carbonaceous aerogels: selective preparation of MnO2@CA composites for supercapacitors.

Science.gov (United States)

Ren, Yumei; Xu, Qun; Zhang, Jianmin; Yang, Hongxia; Wang, Bo; Yang, Daoyuan; Hu, Junhua; Liu, Zhimin

2014-06-25

Functionalized porous carbon materials with hierarchical structure and developed porosity coming from natural and renewable biomass have been attracting tremendous attention recently. In this work, we present a facile and scalable method to synthesize MnO2 loaded carbonaceous aerogel (MnO2@CA) composites via the hydrothermal carbonaceous (HTC) process. We employ two reaction systems of the mixed metal ion precursors to study the optimal selective adsorption and further reaction of MnO2 precursor on CA. Our experimental results show that the system containing KMnO4 and Na2S2O3·5H2O exhibits better electrochemical properties compared with the reaction system of MnSO4·H2O and (NH4)2S2O8. For the former, the obtained MnO2@CA displays the specific capacitance of 123.5 F·g(-1). The enhanced supercapacitance of MnO2@CA nanocomposites could be ascribed to both electrochemical contributions of the loaded MnO2 nanoparticles and the porous structure of three-dimensional carbonaceous aerogels. This study not only indicates that it is vital for the reaction systems to match with porous carbonaceous materials, but also offers a new fabrication strategy to prepare lightweight and high-performance materials that can be used in energy storage devices.

Management of solid residues in waste-to-energy and biomass systems

Energy Technology Data Exchange (ETDEWEB)

Vehlow, J.; Bergfeldt, B. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Technische Chemie; Wilen, C.; Ranta, J. [VTT Technical Research Centre of Finland, Espoo (Finland); Schwaiger, H. [Forschungsgesellschaft Joanneum mbH, Graz (Austria); Visser, H.J.M. [ECN Energy Research Centre of the Netherlands, Petten (Netherlands); Gu, S.; Gyftopoulou, E.; Brammer, J. [Aston Univ., Birmingham (United Kingdom)

2007-12-15

A literature review has been performed for getting in-depth information about quality of residues from thermal processes for waste and biomass as well as their disposal or utilisation options and current practices. Residues from waste incineration have been subject to intense research programs for many years and it can be concluded that the quality of bottom ashes has meanwhile a high standard. The question whether an utilisation as secondary building material is accepted or not depends on the definition of acceptable economic impac. For filter ashes and gas cleaning residues the situation is more complex. Their quality is known: due to their high inventory of heavy metals and organic micro-pollutants they are classified as hazardous waste which means they require specific measures for their safe long-term disposal. A number of stabilisation and treatment processes for filter ashes and gas cleaning residues including the recovery of species out of these materials have been developed but none has been implemented in full scale due to economic constraints. There is reason to speculate that even recovery processes which are not profitable for private companies might point out economically useful if future and long-term costs which have to be covered of the society, e.g. for rehabilitation of contaminated sites, are taken into account. Their quality as well as that of residues from combustion of contaminated biomass is mainly depending on the quality of the fuel. The inventory of critical ingredients in fuel produced from waste or waste fractions, especially of halogens and heavy metals, is often rather high and shows typically a wide range of variation. A reliable quality control for such fuels is very difficult. Other residues can - like gas cleaning residues from waste incineration - be inertised in order to meet the criteria for the access to cheaper landfills than those for hazardous waste. A similar conclusion can be drawn for the quality and management of

Isotopically Anomalous Carbonaceous Nanoglobules in Meteorites and Comets

Science.gov (United States)

de Gregorio, B. T.; Alexander, C.; Bassim, N. D.; Cody, G. D.; Kilcoyne, D.; Nittler, L.; Stroud, R.; Zega, T. J.

2009-12-01

Sub-micron, spherical, organic globules are prevalent in primitive meteorites and interplanetary dust particles. Many of these globules are significantly enriched in 15N and/or D, relative to solar values, which suggest that they or their precursors formed in cold regions of the solar nebula or in interstellar molecular clouds. We have used correlated transmission electron microscopy (TEM), synchrotron-based X-ray absorption near-edge structure spectroscopy (XANES), and secondary ion mass spectrometry (SIMS) to determine the elemental and isotopic composition and organic functional group chemistry of individual carbonaceous nanoglobules in a suite of insoluble organic matter (IOM) residues prepared from carbonaceous and ordinary chondrites, and two additional organic globules from the Stardust comet 81P/Wild 2 sample collection. The majority of the meteoritic nanoglobules have a similar chemistry to the bulk IOM, with, on average, a small but significant enrichment in aromatic ketone (-C=O) and carboxyl (-COOH) functional groups. However, some of the meteoritic nanoglobules and one of the Stardust nanoglobules contain highly aromatic organic matter with no significant oxygen functionality. Preliminary measurements indicate that the highest 15N enrichments are associated with the highly aromatic nanoglobules and that aromatic nanoglobules are more prevalent in IOM from more primitive meteorites (e.g. Bells contains more aromatic globules than Murchison). For example, of two adjacent nanoglobules with nearly identical hollow morphologies from Murchison, one contains highly aromatic organic matter and the other contains oxidized IOM-like organic matter. SIMS analysis of these two globules reveals that the highly aromatic globule has the greatest 15N enrichment (δ15N ~ +500‰) of all meteoritic globules in which both XANES and SIMS was performed, whereas the adjacent IOM-like globule has a smaller 15N enrichment (δ15N ~ +300‰) but still greater than bulk IOM (δ15

Sub-micrometer refractory carbonaceous particles in the polar stratosphere

Directory of Open Access Journals (Sweden)

K. Schütze

2017-10-01

Full Text Available Eleven particle samples collected in the polar stratosphere during SOLVE (SAGE III Ozone loss and validation experiment from January until March 2000 were characterized in detail by high-resolution transmission and scanning electron microscopy (TEM/SEM combined with energy-dispersive X-ray microanalysis. A total of 4202 particles (TEM  =  3872; SEM  =  330 were analyzed from these samples, which were collected mostly inside the polar vortex in the altitude range between 17.3 and 19.9 km. Particles that were volatile in the microscope beams contained ammonium sulfates and hydrogen sulfates and dominated the samples. Some particles with diameters ranging from 20 to 830 nm were refractory in the electron beams. Carbonaceous particles containing additional elements to C and O comprised from 72 to 100 % of the refractory particles. The rest were internal mixtures of these materials with sulfates. The median number mixing ratio of the refractory particles, expressed in units of particles per milligram of air, was 1.1 (mg air−1 and varied between 0.65 and 2.3 (mg air−1. Most of the refractory carbonaceous particles are completely amorphous, a few of the particles are partly ordered with a graphene sheet separation distance of 0.37 ± 0.06 nm (mean value ± standard deviation. Carbon and oxygen are the only detected major elements with an atomic O∕C ratio of 0.11 ± 0.07. Minor elements observed include Si, S, Fe, Cr and Ni with the following atomic ratios relative to C: Si∕C: 0.010 ± 0.011; S∕C: 0.0007 ± 0.0015; Fe∕C: 0.0052 ± 0.0074; Cr∕C: 0.0012 ± 0.0017; Ni∕C: 0.0006 ± 0.0011 (all mean values ± standard deviation.High-resolution element distribution images reveal that the minor elements are distributed within the carbonaceous matrix; i.e., heterogeneous inclusions are not observed. No difference in size, nanostructure and elemental composition was found between

Solid tumors are poroelastic solids with a chemo-mechanical feedback on growth.

Science.gov (United States)

Ambrosi, D; Pezzuto, S; Riccobelli, D; Stylianopoulos, T; Ciarletta, P

2017-12-01

The experimental evidence that a feedback exists between growth and stress in tumors poses challenging questions. First, the rheological properties (the "constitutive equations") of aggregates of malignant cells are still a matter of debate. Secondly, the feedback law (the "growth law") that relates stress and mitotic-apoptotic rate is far to be identified. We address these questions on the basis of a theoretical analysis of in vitro and in vivo experiments that involve the growth of tumor spheroids. We show that solid tumors exhibit several mechanical features of a poroelastic material, where the cellular component behaves like an elastic solid. When the solid component of the spheroid is loaded at the boundary, the cellular aggregate grows up to an asymptotic volume that depends on the exerted compression. Residual stress shows up when solid tumors are radially cut, highlighting a peculiar tensional pattern. By a novel numerical approach we correlate the measured opening angle and the underlying residual stress in a sphere. The features of the mechanobiological system can be explained in terms of a feedback of mechanics on the cell proliferation rate as modulated by the availability of nutrient, that is radially damped by the balance between diffusion and consumption. The volumetric growth profiles and the pattern of residual stress can be theoretically reproduced assuming a dependence of the target stress on the concentration of nutrient which is specific of the malignant tissue.

Composition and sources of carbonaceous aerosols in Northern Europe during winter

NARCIS (Netherlands)

Glasius, M.; Hansen, A.M.K.; Claeys, M.; Henzing, J.S.; Jedynska, A.D.; Kasper-Giebl, A.; Kistler, M.; Kristensen, K.; Martinsson, J.; Maenhaut, W.; Nøjgaard, J.K.; Spindler, G.; Stenström, K.E.; Swietlicki, E.; Szidat, S.; Simpson, D.; Yttri, K.E.

2018-01-01

Sources of elemental carbon (EC) and organic carbon (OC) in atmospheric aerosols (carbonaceous aerosols) were investigated by collection of weekly aerosol filter samples at six background sites in Northern Europe (Birkenes, Norway; Vavihill, Sweden; Risoe, Denmark; Cabauw and Rotterdam in The

Recovery of transuranics from process residues

International Nuclear Information System (INIS)

Gray, J.H.; Gray, L.W.

1987-01-01

Process residues are generated at both the Rocky Flats Plant (RFP) and the Savannah River Plant (SRP) during aqueous chemical and pyrochemical operations. Frequently, process operations will result in either impure products or produce residues sufficiently contaminated with transuranics to be nondiscardable as waste. Purification and recovery flowsheets for process residues have been developed to generate solutions compatible with subsequent Purex operations and either solid or liquid waste suitable for disposal. The ''scrub alloy'' and the ''anode heel alloy'' are examples of materials generated at RFP which have been processed at SRP using the developed recovery flowsheets. Examples of process residues being generated at SRP for which flowsheets are under development include LECO crucibles and alpha-contaminated hydraulic oil

Adsorption of perfluoroalkyl acids by carbonaceous adsorbents: Effect of carbon surface chemistry

International Nuclear Information System (INIS)

Zhi, Yue; Liu, Jinxia

2015-01-01

Adsorption by carbonaceous sorbents is among the most feasible processes to remove perfluorooctane sulfonic (PFOS) and carboxylic acids (PFOA) from drinking and ground waters. However, carbon surface chemistry, which has long been recognized essential for dictating performance of such sorbents, has never been considered for PFOS and PFOA adsorption. Thus, the role of surface chemistry was systematically investigated using sorbents with a wide range in precursor material, pore structure, and surface chemistry. Sorbent surface chemistry overwhelmed physical properties in controlling the extent of uptake. The adsorption affinity was positively correlated carbon surface basicity, suggesting that high acid neutralizing or anion exchange capacity was critical for substantial uptake of PFOS and PFOA. Carbon polarity or hydrophobicity had insignificant impact on the extent of adsorption. Synthetic polymer-based Ambersorb and activated carbon fibers were more effective than activated carbon made of natural materials in removing PFOS and PFOA from aqueous solutions. - Highlights: • Adsorption of PFOS and PFOA by ten carbonaceous adsorbents were compared. • Surface chemistry of the adsorbents controlled adsorption affinity. • Carbon surface basicity was positively correlated with the extent of PFOS and PFOA uptake. • Carbon polarity or hydrophobicity was not correlated with adsorption affinity. • Synthetic polymer-based adsorbents were more effective in removing PFOS and PFOA. - Carbon surface basicity is the primary factor that influences adsorption affinity of the carbonaceous sorbents for perfluorooctane sulfonic and carboxylic acids

Interaction of acid mine drainage with Ordinary Portland Cement blended solid residues generated from active treatment of acid mine drainage with coal fly ash.

Science.gov (United States)

Gitari, Wilson M; Petrik, Leslie F; Key, David L; Okujeni, Charles

2011-01-01

Fly ash (FA) has been investigated as a possible treatment agent for Acid mine drainage (AMD) and established to be an alternative, cheap and economically viable agent compared to the conventional alkaline agents. However, this treatment option also leads to generation of solid residues (SR) that require disposal and one of the proposed disposal method is a backfill in coal mine voids. In this study, the interaction of the SR with AMD that is likely to be present in such backfill scenario was simulated by draining columns packed with SR and SR + 6% Ordinary Portland Cement (OPC) unsaturated with simulated AMD over a 6 month period. The evolving geochemistry of the liquid/solid (L/S) system was evaluated in-terms of the mineral phases likely or controlling contaminants attenuation at the different pH regimes generated. Stepwise acidification of the percolates was observed as the drainage progressed. Two pH buffer zones were observed (7.5-9 and 3-4) for SR and (11.2-11.3 and 3.5-4) for SR + 6% OPC. The solid residue cores (SR) appeared to have a significant buffering capacity, maintaining a neutral to slightly alkaline pH in the leachates for an extended period of time (97 days: L/S 4.3) while SR + 6% OPC reduced this neutralization capacity to 22 days (L/S 1.9). Interaction of AMD with SR or SR + 6% OPC generated alkaline conditions that favored precipitation of Fe, Al, Mn-(oxy) hydroxides, Fe and Ca-Al hydroxysulphates that greatly contributed to the contaminants removal. However, precipitation of these phases was restricted to the pH of the leachates remaining at neutral to circum-neutral levels. Backfill of mine voids with SR promises to be a feasible technology for the disposal of the SR but its success will greatly depend on the disposal scenario, AMD generated and the alkalinity generating potential of the SR. A disadvantage would be the possible re-dissolution of the precipitated phases at pH water column. However extrapolation of this concept to a field

Carbonaceous aerosol characteristics over Delhi in Northern India: Seasonal variability and possible sources

Science.gov (United States)

Srivastava, Atul Kumar; Bisht, Ds; Tiwari, S.

Carbonaceous aerosols have been the focus of extensive studies during the last decade due to its significant impacts on human health, visibility and climate change. As per Asian regions are concerned, aerosols in south-Asia are gaining considerable importance because of their potential impacts on regional climate, yet their possible sources are poorly understood. Semi-continuous measurements of organic carbon (OC) and elemental carbon (EC) and continuous measurements of black carbon (BC) aerosols were conducted simultaneously at Delhi during the period from January 2011 to May 2012. Delhi is the capital city of India and one of the densely populated and industrialized urban megacities in Asia, located at the Ganga basin in the northern part of India. Being highly polluted region, mass concentrations of OC, EC and BC over Delhi were found to vary from about 6-92 mug m (-3) (mean: 23±16 mug m (-3) ), 3-38 mug m (-3) (mean: 11±7 mug m (-3) ) and 1-24 mug m (-3) (mean: 7±5 mug m (-3) ), respectively during the entire measurement period, with about two times higher concentration during winter as compared to summer. A significant correlation between OC and EC (R=0.95, n=232) and relatively lower OC/EC ratio (range: 1.0-3.6; mean: 2.2±0.5) suggest fossil fuel emission as a dominant source of carbonaceous aerosols over the station. The average mass concentration of EC was found about 38% higher than BC during the study period, which is interestingly different as reported at other locations over Ganga basin. We also determined the associated optical properties of carbonaceous species (e.g. absorption coefficient and mass absorption efficiency) over the station. Significant loading of carbonaceous species over such regions emphasize an urgent need to focus on air quality management and proper impact assessment on health perspective.

Electroremediation of air pollution control residues in a continuous reactor

DEFF Research Database (Denmark)

Jensen, Pernille Erland; Ferreira, Célia M. D.; Hansen, Henrik K.

2010-01-01

Air pollution control (APC) residue from municipal solid waste incineration is considered hazardous waste due to its alkalinity and high content of salts and mobile heavy metals. Various solutions for the handling of APC-residue exist, however most commercial solutions involve landfilling. A demand...... were made with raw residue, water-washed residue, acid washed residue and acid-treated residue with emphasis on reduction of heavy metal mobility. Main results indicate that the reactor successfully removes toxic elements lead, copper, cadmium and zinc from the feed stream, suggesting...

Anaerobic digestion of cider apple residues

Energy Technology Data Exchange (ETDEWEB)

Contreras Lopez, A. (E.T.S.I.I., U.N.E.D., Madrid (Spain). Dept. Quimica Applicada a la Ingenieria); Lopez Bobo, R. (E.T.S. Ingeneiros Industriales, Asturias (Spain). Dept. de Energia)

1992-12-01

Apple residue from the cider industry is used here for anaerobic fermentation. The effect of retention time and volatile solids concentration on the production of biogas and methane was investigated by using continuously mixed anaerobic fermentors with a working volume of 1 1. The maximum proportions of biogas and methane obtained were 430 1 biogas/kg per day (12 days' retention time and 3% of volatile solids) and 281 1 of methane per day (a retention time of 30 days and 2% of volatile solids), respectively. (author)

Preparing patterned carbonaceous nanostructures directly by overexposure of PMMA using electron-beam lithography

Energy Technology Data Exchange (ETDEWEB)

Duan Huigao; Zhao Jianguo; Zhang Yongzhe; Xie Erqing [School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); Han Li [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China)], E-mail: duanhg@gmail.com, E-mail: xieeq@lzu.edu.cn

2009-04-01

The overexposure process of poly(methyl methacrylate) (PMMA) was studied in detail using electron-beam lithography. It was found that PMMA films could be directly patterned without development due to the electron-beam-induced collapse of PMMA macromolecular chains. By analyzing the evolution of surface morphologies and compositions of the overexposed PMMA films, it was also found that the transformation of PMMA from positive to negative resist was a carbonization process, so patterned carbonaceous nanostructures could be prepared directly by overexposure of PMMA using electron-beam lithography. This simple one-step process for directly obtaining patterned carbonaceous nanostructures has promising potential application as a tool to make masks and templates, nanoelectrodes, and building blocks for MEMS and nanophotonic devices.

Determination of some selected pesticide residues in apple juice by solid-phase microextraction coupled to gas chromatography – mass spectrometry

Directory of Open Access Journals (Sweden)

Andrea Hercegová

2011-01-01

Full Text Available The performance of solid phase microextraction (SPME for enrichment of pesticides from apple juice was investigated. Samples were diluted with water, extracted by solid-phase microextraction and analysed by gas chromatography using mass-spectrometry detector (MSD in selected ion monitoring mode (SIM. The method was tested for the following pesticides used mostly in fruit culturing at Slovakia: tebuthylazine, fenitrothion, chlorpyrifos, myclobutanil, cyprodinil, phosalone, pyrimethanil, tebuconazole, kresoxim-methyl, methidathion, penconazole. All pesticides were extracted with polydimethylsiloxane fibre 100 μm thickness. The linear concentration range of application was 0.05 μg dm−3–10 μg dm−3. The method described provides detectabilities complying with the maximum residue levels (MRLs set by regulatory organizations for pesticides in apple juice matrices. The solvent – free SPME procedure was found to be quicker and more cost effective then the solvent extraction methods commonly used.

PCB congener sorption to carbonaceous sediment components: Macroscopic comparison and characterization of sorption kinetics and mechanism

International Nuclear Information System (INIS)

Choi, Hyeok; Al-Abed, Souhail R.

2009-01-01

Sorption of polychlorinated biphenyls (PCBs) to sediment is a key process in determining their mobility, bioavailability, and chemical decomposition in aquatic environments. In order to examine the validity of currently used interpretation approaches for PCBs sorption, comparative results on 2-chlorobiphenyl sorption to carbonaceous components in sediments (activated carbon, carbon black, coal, soot, graphite, flyash, wood) were macroscopically correlated with the structural, morphological, crystallographic, and compositional properties of the carbonaceous components. Since the Freundlich sorption constant, K F (L kg -1 ) spanned several orders of magnitude, ranging from log K F of 6.13-5.27 for activated carbon, 5.04 for carbon black, 3.83 for coal to 3.08 for wood, organic carbon partitioning approach should be more specifically categorized, considering the various forms, nature and origins of organic carbon in sediment. Sorption rate constants and fraction parameters, which were numerically defined from empirical kinetic model with fast and slow sorption fractions, were closely related to the physicochemical properties of the carbonaceous components. Sorption interpretation approaches with a specific property and viewpoint, such as organic carbon partitioning, soot carbon distribution, or surface area correlation, did not properly explain the overall results on sorption capacity, fast and slow sorption kinetics, and partitioning coefficient. It is also important to emphasize the heterogeneous nature of sediment and the difficulties of encompassing the partitioning among its carbonaceous components.

PCB congener sorption to carbonaceous sediment components: Macroscopic comparison and characterization of sorption kinetics and mechanism

Energy Technology Data Exchange (ETDEWEB)

Choi, Hyeok [National Risk Management Research Laboratory, U.S. Environmental Protection Agency, 26 West Martin Luther King Drive, Cincinnati, OH 45268 (United States); Al-Abed, Souhail R., E-mail: al-abed.souhail@epa.gov [National Risk Management Research Laboratory, U.S. Environmental Protection Agency, 26 West Martin Luther King Drive, Cincinnati, OH 45268 (United States)

2009-06-15

Sorption of polychlorinated biphenyls (PCBs) to sediment is a key process in determining their mobility, bioavailability, and chemical decomposition in aquatic environments. In order to examine the validity of currently used interpretation approaches for PCBs sorption, comparative results on 2-chlorobiphenyl sorption to carbonaceous components in sediments (activated carbon, carbon black, coal, soot, graphite, flyash, wood) were macroscopically correlated with the structural, morphological, crystallographic, and compositional properties of the carbonaceous components. Since the Freundlich sorption constant, K{sub F} (L kg{sup -1}) spanned several orders of magnitude, ranging from log K{sub F} of 6.13-5.27 for activated carbon, 5.04 for carbon black, 3.83 for coal to 3.08 for wood, organic carbon partitioning approach should be more specifically categorized, considering the various forms, nature and origins of organic carbon in sediment. Sorption rate constants and fraction parameters, which were numerically defined from empirical kinetic model with fast and slow sorption fractions, were closely related to the physicochemical properties of the carbonaceous components. Sorption interpretation approaches with a specific property and viewpoint, such as organic carbon partitioning, soot carbon distribution, or surface area correlation, did not properly explain the overall results on sorption capacity, fast and slow sorption kinetics, and partitioning coefficient. It is also important to emphasize the heterogeneous nature of sediment and the difficulties of encompassing the partitioning among its carbonaceous components.

AFM measurements of adhesive forces between carbonaceous particles and the substrates

Energy Technology Data Exchange (ETDEWEB)

Zhang, Tianqi [Institute of Nuclear and New Energy Technology of Tsinghua University, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Beijing 100084 (China); Peng, Wei, E-mail: pengwei@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology of Tsinghua University, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Beijing 100084 (China); Shen, Ke [Institute of Nuclear and New Energy Technology of Tsinghua University, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Beijing 100084 (China); Yu, Suyuan, E-mail: suyuan@tsinghua.edu.cn [Center for Combustion Energy, Key Laboratory for Thermal Science and Power Engineering of Ministry of Educations, Department of Thermal Engineering, Tsinghua University, Beijing 100084 (China)

2015-11-15

Highlights: • Adhesive force of spherical carbonaceous particle MCMBs and HTR-10 graphite matrix debris were measured for the first time. • The measured equivalent works of adhesion were much smaller than the ideal values. • The shape factor and the particle morphology reduce the adhesive force. • The adhesion effect does not change directly with the asperity size. - Abstract: Graphite dust is carbonaceous particles generated during operation of High Temperature Gas-Cooled Reactors (HTR). Graphite dust resuspension is the key behavior associated with HTR source term analyses and environmental safety assessment. The adhesive force is the key factor that determines the resuspension rate. The present study used an atomic force microscope (AFM) to measure the adhesive force between a single carbonaceous particle and the substrate. The measurements were performed on mica, graphite IG110 and Inconel 800H. The prepared “probe cantilevers” were mesocarbon microbeads (MCMB), fuel element debris from HTR-10 and graphite NBG18. The equivalent work of adhesion was derived from the measured adhesive force and calculated based on substrate profile approximation and the JKR theoretical model. The measured work was smaller than the ideal work of adhesion, most likely due to the rough particle morphology and the rough substrate surface. Additionally, a shape factor imposes a constraint on the lateral deformation of the particles. Furthermore, surface roughness could reduce the adhesive force some depending on the particle size. Once the particle was too small to be trapped into a trough, the adhesive force would not be further reduced.

AFM measurements of adhesive forces between carbonaceous particles and the substrates

International Nuclear Information System (INIS)

Zhang, Tianqi; Peng, Wei; Shen, Ke; Yu, Suyuan

2015-01-01

Highlights: • Adhesive force of spherical carbonaceous particle MCMBs and HTR-10 graphite matrix debris were measured for the first time. • The measured equivalent works of adhesion were much smaller than the ideal values. • The shape factor and the particle morphology reduce the adhesive force. • The adhesion effect does not change directly with the asperity size. - Abstract: Graphite dust is carbonaceous particles generated during operation of High Temperature Gas-Cooled Reactors (HTR). Graphite dust resuspension is the key behavior associated with HTR source term analyses and environmental safety assessment. The adhesive force is the key factor that determines the resuspension rate. The present study used an atomic force microscope (AFM) to measure the adhesive force between a single carbonaceous particle and the substrate. The measurements were performed on mica, graphite IG110 and Inconel 800H. The prepared “probe cantilevers” were mesocarbon microbeads (MCMB), fuel element debris from HTR-10 and graphite NBG18. The equivalent work of adhesion was derived from the measured adhesive force and calculated based on substrate profile approximation and the JKR theoretical model. The measured work was smaller than the ideal work of adhesion, most likely due to the rough particle morphology and the rough substrate surface. Additionally, a shape factor imposes a constraint on the lateral deformation of the particles. Furthermore, surface roughness could reduce the adhesive force some depending on the particle size. Once the particle was too small to be trapped into a trough, the adhesive force would not be further reduced.

Molecular and elemental analyses of the carbonaceous matter in the gold and uranium bearing Vaal Reef carbon seams, Witwatersrand sequence

International Nuclear Information System (INIS)

Zumberge, J.E.; Sigleo, A.C.; Nagy, B.

1978-01-01

The thin Vaal Reef carbon seams consist of a complex, solid, and solvent insoluble, polymer-like substance, containing mainly hydrocarbons and some organic sulphur and oxygen compounds. These carbon seams are not pure carbon, e.g. graphite, and do not contain only hydrocarbons. According to modern terminology the Vaal Reef carbonaceous matter is most appropriately referred to as kerogen rather than carbon or thucholite. This kerogen is not the result of the polymerization of gaseous or liquid hydrocarbons, but rather of the polymerization of biochemicals from decayed, primitive Precambrian micro-organisms. These microbiota formed mats in which uranium minerals and gold became incorporated before burial under younger sediments. Organic geochemistry was first developed as a means to elucidate the nature and composition of petroleum and coal. Later it was successfully used in lunar sample, planetary surface, and meteorite studies as well as in investigations of kerogens in terrestrial sediments of various ages. Considering economic geology, organic geochemistry holds promise for elucidating the origin and helping in the exploration of carbonaceous ore deposits. The purpose of this report is to review some of the major current organic geochemical methods and to illustrate these by the analysis of the Vaal Reef kerogen. The samples were analysed by a directly connected high vacuum pyrolysis system-gas chromatograph-organic mass spectrometer. Additional analyses were performed by a combined scanning electron microscope-electron microprobe, by the techniques of electron paramagnetic resonance spectroscopy, and by neutron activation analysis

Regenerable mixed copper-iron-inert support oxygen carriers for solid fuel chemical looping combustion process

Energy Technology Data Exchange (ETDEWEB)

Siriwardane, Ranjani V.; Tian, Hanjing

2016-12-20

The disclosure provides an oxygen carrier for a chemical looping cycle, such as the chemical looping combustion of solid carbonaceous fuels, such as coal, coke, coal and biomass char, and the like. The oxygen carrier is comprised of at least 24 weight % (wt %) CuO, at least 10 wt % Fe2O3, and an inert support, and is typically a calcine. The oxygen carrier exhibits a CuO crystalline structure and an absence of iron oxide crystalline structures under XRD crystallography, and provides an improved and sustained combustion reactivity in the temperature range of 600.degree. C.-1000.degree. C. particularly for solid fuels such as carbon and coal.

Alternatives of Treatment and Final Disposition of the Solid Hospital residuals; Alternativas de Tratamiento y Disposicion Final de los Residuos Solidos Hospitalarios

Energy Technology Data Exchange (ETDEWEB)

Meza Monge, K

1998-07-01

The current handling, treatment and final disposition of the hospital solid waste in Costa Rica are considered inadequate or at least insufficient. This situation represents a serious danger for the population's health and the environment, because they are exposed to infectious agents, toxic substances and even radioactive products that are generated among the residuals of the centers of health. This work, alternatives propose for the treatment and adequate final disposition of the solid waste produced in the hospitals of the country. They take into consideration the characteristics that present these residuals, the advantages and disadvantages of each one of the existent techniques and the technical and economic possibilities of the country. For this purpose, in first instance, a revision about the properties, the quality and the quantity of the solid waste produced by the national hospital centers was carried out. Also, a diagnostic of the current situation of the treatment and final disposition of these residuals in some of the most important hospitals of the country, as well as of the possibilities of physical space with that they count on was carried out. Then, the existent different treatment techniques and final disposition for the solid waste that comes from the centers of health are described, as well as their advantages and disadvantages and a comparative analysis of the same ones is carried out. The objective is completed, since alternatives of treatment and final disposition that are considered appropriate for this type of residuals are planned. Nevertheless, in the future, more detailed investigations and studies of feasibility, with the purpose of developing handling programs and elimination of the solid waste for each one of the hospital centers in Costa Rica should be carried out. (Author) [Spanish] El actual manejo, tratamiento y disposicion final de los desechos solidos hospitalarios en Costa Rica se considera inadecuado o cuando menos

Achievement of solid-state plasma fusion ('Cold-Fusion')

International Nuclear Information System (INIS)

Arata, Yoshiaki; Zhang, Yue-Chang

1995-01-01

Using a 'QMS' (Quadrupole Mass Spectrometer), the authors detected a significantly large amount (10 20 -10 21 [cm -3 ]) of helium ( 2 4 He), which was concluded to have been produced by a deuterium nuclear reaction within a host solid. These results were found to be fully repeatable and supported the authors' proposition that solid state plasma fusion ('Cold Fusion') can be generated in energetic deuterium Strongly Coupled Plasma ('SC-plasma'). This fusion reaction is thought to be sustained by localized 'Latticequake' in a solid-state media with the deuterium density equivalent to that of the host solid. While exploring this basic proposition, the characteristic differences when compared with ultra high temperature-state plasma fusion ('Hot Fusion') are clarified. In general, the most essential reaction product in both types of the deuterium plasma fusion is considered to be helium, irrespective of the 'well-known and/or unknown reactions', which is stored within the solid-state medium in abundance as a 'Residual Product', but which generally can not enter into nor be released from host-solid at a room temperature. Even measuring instruments with relatively poor sensitivity should be able to easily detect such residual helium. An absence of residual helium means that no nuclear fusion reaction has occurred, whereas its presence provides crucial evidence that nuclear fusion has, in fact, occurred in the solid. (author)

Conditions of formation for carbonaceous silicites of the continental margins

Energy Technology Data Exchange (ETDEWEB)

Bazhenova, O.K.

1986-06-01

Carbonaceous silicites occur in virtually all systems in Phanerozoic folded regions. They are of practical interest as concentrators of silver, molybdenum, vanadium, and nickel and as source and occasionally reservoir beds for petroleum. Some small oil pools occur in them in basins in Japan (Niigata and Akita), California, and East Sakhalin. Recently, interest has increased because a major pool was discovered in silicites of the Monterey formation: Point Arguello Hueso in the offshore part of the Santa Maria basin. Here the authors consider carbonaceous silicates in the western part of the Pacific active margin, which include Silurian and Devonian phthanites in the Mongolia-Okhotsk belt, and Triassic and Jurassic phthanites in the Sikhote-Alin area, although these rocks are of fairly local occurrence in the section. The authors have examined silicites in Kamchatka, Sakhalin, and Chukotka: diatomites, tuff-diatomites, and opokas, together with their recrystallized analogs. They occur in the Paleogene, but they are most abundant in the Miocene and Pliocene, as well as in the Jurassic, Cretaceous, and Eocene, particularly in the Miocene of California and Japan. 16 references.

Selective reduction of nitric oxide over Cu/ZSM-5: The role of oxygen in suppressing catalyst deactivation by carbonaceous deposits

Energy Technology Data Exchange (ETDEWEB)

d' Itri, Julie L; Sachtler, Wolfgang M.H. [V.N. Ipatieff Laboratory, Center for Catalysis and Surface Science, Departments of Chemical Engineering and Chemistry, Northwestern University, Evanston, IL (United States)

1993-06-15

The role of oxygen in the selective reduction of nitrogen monoxide by either propane or propene over 'excessively' ion-exchanged Cu/ZSM-5 has been studied. In a wide temperature region and in the absence of additives such as steam, propane is a more effective reductant than propene; with propane and in the presence of oxygen reduction of nitric oxide to nitrogen approaches 100% above 600 K. The difference in effectiveness is due to the different degree of catalyst deactivation by carbonaceous deposits: more carbonaceous material is deposited from propene than from propane. Temperature-programmed oxidation shows that above 600 K the rate of oxidation of carbonaceous deposits by oxygen is significant. The amount of such carbonaceous deposits is, therefore, lower when catalytic tests above 600 K are done in the presence of oxygen. At very high temperatures, the in situ volatilization of the deposits by reaction with oxygen keeps the catalyst surface clean in the steady state of nitric oxide reduction.

Thermal treatment of solid residues from WtE units: A review

International Nuclear Information System (INIS)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-01-01

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field

Thermal treatment of solid residues from WtE units: A review

Energy Technology Data Exchange (ETDEWEB)

Lindberg, Daniel, E-mail: daniel.lindberg@abo.fi; Molin, Camilla, E-mail: camilla.molin@abo.fi; Hupa, Mikko, E-mail: mikko.hupa@abo.fi

2015-03-15

Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field.

Morphology, composition, and mixing state of primary particles from combustion sources - crop residue, wood, and solid waste.

Science.gov (United States)

Liu, Lei; Kong, Shaofei; Zhang, Yinxiao; Wang, Yuanyuan; Xu, Liang; Yan, Qin; Lingaswamy, A P; Shi, Zongbo; Lv, Senlin; Niu, Hongya; Shao, Longyi; Hu, Min; Zhang, Daizhou; Chen, Jianmin; Zhang, Xiaoye; Li, Weijun

2017-07-11

Morphology, composition, and mixing state of individual particles emitted from crop residue, wood, and solid waste combustion in a residential stove were analyzed using transmission electron microscopy (TEM). Our study showed that particles from crop residue and apple wood combustion were mainly organic matter (OM) in smoldering phase, whereas soot-OM internally mixed with K in flaming phase. Wild grass combustion in flaming phase released some Cl-rich-OM/soot particles and cardboard combustion released OM and S-rich particles. Interestingly, particles from hardwood (pear wood and bamboo) and softwood (cypress and pine wood) combustion were mainly soot and OM in the flaming phase, respectively. The combustion of foam boxes, rubber tires, and plastic bottles/bags in the flaming phase released large amounts of soot internally mixed with a small amount of OM, whereas the combustion of printed circuit boards and copper-core cables emitted large amounts of OM with Br-rich inclusions. In addition, the printed circuit board combustion released toxic metals containing Pb, Zn, Sn, and Sb. The results are important to document properties of primary particles from combustion sources, which can be used to trace the sources of ambient particles and to know their potential impacts in human health and radiative forcing in the air.

Quality Assessment of solid waste used for obtaining biogas

International Nuclear Information System (INIS)

Tamayo Cuellar, Ernesto Antonio; Menendez Perez, Manuel German

2011-01-01

The solid residuals are in our days an important factor in the processes of recycling of materials, composting and obtaining of biogas, however, sometimes doesn't keep in mind the quality of these for their productive acting. Therefore the present work has as objective, in the peculiar case of the biogas production, to propose a method to evaluate the quality of the solid residuals used in the biogas process starting from the biodegradable organic fraction contained in these. For the investigative development of the work theoretical methods were used as the hypothetical-deductive method, the systemic one, the structural-functional one and empiric methods as the scientific observation and the mensuration. The results of their application, although discreet still, have been evidenced in the evaluation of the quality of the solid residuals in the plant of recycling -composting of the City of Holguin in the compost production. The main conclusion to which you can arrive with the carried out investigation is that the evaluation of the quality of the solid residuals is important to make studies of feasibility in the design and implementation of new projects of recycling units, composting and biogas. (author)

Mobility of organic carbon from incineration residues

International Nuclear Information System (INIS)

Ecke, Holger; Svensson, Malin

2008-01-01

Dissolved organic carbon (DOC) may affect the transport of pollutants from incineration residues when landfilled or used in geotechnical construction. The leaching of dissolved organic carbon (DOC) from municipal solid waste incineration (MSWI) bottom ash and air pollution control residue (APC) from the incineration of waste wood was investigated. Factors affecting the mobility of DOC were studied in a reduced 2 6-1 experimental design. Controlled factors were treatment with ultrasonic radiation, full carbonation (addition of CO 2 until the pH was stable for 2.5 h), liquid-to-solid (L/S) ratio, pH, leaching temperature and time. Full carbonation, pH and the L/S ratio were the main factors controlling the mobility of DOC in the bottom ash. Approximately 60 weight-% of the total organic carbon (TOC) in the bottom ash was available for leaching in aqueous solutions. The L/S ratio and pH mainly controlled the mobilization of DOC from the APC residue. About 93 weight-% of TOC in the APC residue was, however, not mobilized at all, which might be due to a high content of elemental carbon. Using the European standard EN 13 137 for determination of total organic carbon (TOC) in MSWI residues is inappropriate. The results might be biased due to elemental carbon. It is recommended to develop a TOC method distinguishing between organic and elemental carbon

Rare Earth Element Phases in Bauxite Residue

Directory of Open Access Journals (Sweden)

Johannes Vind

2018-02-01

Full Text Available The purpose of present work was to provide mineralogical insight into the rare earth element (REE phases in bauxite residue to improve REE recovering technologies. Experimental work was performed by electron probe microanalysis with energy dispersive as well as wavelength dispersive spectroscopy and transmission electron microscopy. REEs are found as discrete mineral particles in bauxite residue. Their sizes range from <1 μm to about 40 μm. In bauxite residue, the most abundant REE bearing phases are light REE (LREE ferrotitanates that form a solid solution between the phases with major compositions (REE,Ca,Na(Ti,FeO3 and (Ca,Na(Ti,FeO3. These are secondary phases formed during the Bayer process by an in-situ transformation of the precursor bauxite LREE phases. Compared to natural systems, the indicated solid solution resembles loparite-perovskite series. LREE particles often have a calcium ferrotitanate shell surrounding them that probably hinders their solubility. Minor amount of LREE carbonate and phosphate minerals as well as manganese-associated LREE phases are also present in bauxite residue. Heavy REEs occur in the same form as in bauxites, namely as yttrium phosphates. These results show that the Bayer process has an impact on the initial REE mineralogy contained in bauxite. Bauxite residue as well as selected bauxites are potentially good sources of REEs.

Characterization of combustion-generated carbonaceous nanoparticles by size-dependent ultraviolet laser photoionization.

Science.gov (United States)

Commodo, Mario; Sgro, Lee Anne; Minutolo, Patrizia; D'Anna, Andrea

2013-05-16

Photoelectric charging of particles is a powerful tool for online characterization of submicrometer aerosol particles. Indeed photoionization based techniques have high sensitivity and chemical selectivity. Moreover, they yield information on electronic properties of the material and are sensitive to the state of the surface. In the present study the photoionization charging efficiency, i.e., the ratio between the generated positive ions and the corresponding neutral ones, for different classes of flame-generated carbonaceous nanoparticles was measured. The fifth harmonics of a Nd:YAG laser, 213 nm (5.82 eV), was used as an ionization source for the combustion generated nanoparticles, whereas a differential mobility analyzer (DMA) coupled to a Faraday cup electrometer was used for particle classification and detection. Carbonaceous nanoparticles in the nucleation mode, i.e., sizes ranging from 1 to 10 nm, show a photoionization charging efficiency clearly dependent on the flame conditions. In particular, we observed that the richer the flame is, i.e., the higher the equivalent ratio is, the higher the photon charging efficiency is. We hypothesized that such an increase in the photoionization propensity of the carbonaceous nanoparticles from richer flame condition is associated to the presence within the particles of larger aromatic moieties. The results clearly show that photoionization is a powerful diagnostic tool for the physical-chemical characterization of combustion aerosol, and it may lead to further insights into the soot formation mechanism.

Enantiomer excesses of rare and common sugar derivatives in carbonaceous meteorites

Science.gov (United States)

Cooper, George; Rios, Andro C.

2016-06-01

Biological polymers such as nucleic acids and proteins are constructed of only one—the d or l—of the two possible nonsuperimposable mirror images (enantiomers) of selected organic compounds. However, before the advent of life, it is generally assumed that chemical reactions produced 50:50 (racemic) mixtures of enantiomers, as evidenced by common abiotic laboratory syntheses. Carbonaceous meteorites contain clues to prebiotic chemistry because they preserve a record of some of the Solar System’s earliest (˜4.5 Gy) chemical and physical processes. In multiple carbonaceous meteorites, we show that both rare and common sugar monoacids (aldonic acids) contain significant excesses of the d enantiomer, whereas other (comparable) sugar acids and sugar alcohols are racemic. Although the proposed origins of such excesses are still tentative, the findings imply that meteoritic compounds and/or the processes that operated on meteoritic precursors may have played an ancient role in the enantiomer composition of life’s carbohydrate-related biopolymers.

Enantiomer excesses of rare and common sugar derivatives in carbonaceous meteorites.

Science.gov (United States)

Cooper, George; Rios, Andro C

2016-06-14

Biological polymers such as nucleic acids and proteins are constructed of only one-the d or l-of the two possible nonsuperimposable mirror images (enantiomers) of selected organic compounds. However, before the advent of life, it is generally assumed that chemical reactions produced 50:50 (racemic) mixtures of enantiomers, as evidenced by common abiotic laboratory syntheses. Carbonaceous meteorites contain clues to prebiotic chemistry because they preserve a record of some of the Solar System's earliest (∼4.5 Gy) chemical and physical processes. In multiple carbonaceous meteorites, we show that both rare and common sugar monoacids (aldonic acids) contain significant excesses of the d enantiomer, whereas other (comparable) sugar acids and sugar alcohols are racemic. Although the proposed origins of such excesses are still tentative, the findings imply that meteoritic compounds and/or the processes that operated on meteoritic precursors may have played an ancient role in the enantiomer composition of life's carbohydrate-related biopolymers.

Source apportionment of atmospheric carbonaceous particulate matter based on the radiocarbon

International Nuclear Information System (INIS)

Guang-hua Wang; You-shi Zeng; Jian Yao; Yuan Qian; Ke Liu; Wei Liu; Yan Li; Yu Huang; University of South China, Hunan

2013-01-01

A method was established to quantitatively estimate sources of atmospheric carbonaceous matter, using a combination of radiocarbon technology, linear regression of organic carbon (OC) -K + and elemental carbon (EC) tracer method. Fractional contributions of fossil fuels, biomass burning, biogenic secondary organic carbon (BSOC) and soil dust to the atmospheric size-resolved carbonaceous matters in Shanghai suburb were estimated using this new method. The fossil carbon contributed most of the OC in particles smaller than 0.49 μm, and its fraction decreased with the increase of particle size. Biomass burning contributed 17-28 % to the OC. The BSOC contributed comparable proportions to the OC in particles smaller than 3.0 μm with the biomass burning, but larger in the particles lager than 3.0 μm. The soil dust contributed least fraction to the OC of each size with a proportion of 2-13 %. The biomass burning and fossil sources shared comparable fraction of the EC in all size range. (author)

Fuel characteristics and pyrolysis studies of solvent extractables and residues from the evergreen shrub Calotropis procera

Energy Technology Data Exchange (ETDEWEB)

Erdman, M.D.; Gregorski, K.S.; Pavlath, A.E.

1984-01-01

Solvent extractables and residues from milkweed were evaluated as sources of liquid and solid fuels. Selected chemical, physical and pyrolytic determinations of the extractables and residues indicated that hexane extract is a potentially valuable, high density fuel resource. Methanol extract was shown to be a lower energy, highly toxic extract. Extracted residues were demonstrated to be valuable as solid fuel energy resources. 31 references.

Thermal treatment of solid residues from WtE units: a review.

Science.gov (United States)

Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

2015-03-01

Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization of emissions from South Asian biofuels and application to source apportionment of carbonaceous aerosol in the Himalayas

Science.gov (United States)

Stone, Elizabeth A.; Schauer, James J.; Pradhan, Bidya Banmali; Dangol, Pradeep Man; Habib, Gazala; Venkataraman, Chandra; Ramanathan, V.

2010-03-01

This study focuses on improving source apportionment of carbonaceous aerosol in South Asia and consists of three parts: (1) development of novel molecular marker-based profiles for real-world biofuel combustion, (2) application of these profiles to a year-long data set, and (3) evaluation of profiles by an in-depth sensitivity analysis. Emissions profiles for biomass fuels were developed through source testing of a residential stove commonly used in South Asia. Wood fuels were combusted at high and low rates, which corresponded to source profiles high in organic carbon (OC) or high in elemental carbon (EC), respectively. Crop wastes common to the region, including rice straw, mustard stalk, jute stalk, soybean stalk, and animal residue burnings, were also characterized. Biofuel profiles were used in a source apportionment study of OC and EC in Godavari, Nepal. This site is located in the foothills of the Himalayas and was selected for its well-mixed and regionally impacted air masses. At Godavari, daily samples of fine particulate matter (PM2.5) were collected throughout the year of 2006, and the annual trends in particulate mass, OC, and EC followed the occurrence of a regional haze in South Asia. Maximum concentrations occurred during the dry winter season and minimum concentrations occurred during the summer monsoon season. Specific organic compounds unique to aerosol sources, molecular markers, were measured in monthly composite samples. These markers implicated motor vehicles, coal combustion, biomass burning, cow dung burning, vegetative detritus, and secondary organic aerosol as sources of carbonaceous aerosol. A molecular marker-based chemical mass balance (CMB) model provided a quantitative assessment of primary source contributions to carbonaceous aerosol. The new profiles were compared to widely used biomass burning profiles from the literature in a sensitivity analysis. This analysis indicated a high degree of stability in estimates of source

Electrodialytic remediation of air pollution control residues in bench scale

DEFF Research Database (Denmark)

Jensen, Pernille Erland; Ferreira, Celia; Hansen, Henrik K.

2008-01-01

Air pollution control (APC) residue from municipal solid waste incineration (MSWI) is considered a hazardous waste due to its alkalinity and high content of salts and mobile heavy metals. Various solutions for the handling of APC-residue exist in different regions; however, most commercial soluti...

Solid state fermentation studies of citric acid production

African Journals Online (AJOL)

SERVER

2008-03-04

Mar 4, 2008 ... solid waste management, biomass energy conservation, production of high value products and little risk ... The carrier, sugarcane bagasse for solid state fermentation was procured from National Sugar Institute ... constant weight and designated as dry solid residue (DSR). The filtrate (consisting of biomass, ...

Tratamento anaeróbio de resíduos orgânicos com baixa concentração de sólidos Anaerobic treatment of organic wastes with low concentration of solids

Directory of Open Access Journals (Sweden)

Maria L. D. de Luna

2009-03-01

Full Text Available Este trabalho foi realizado com o objetivo de avaliar o desempenho de reator anaeróbio compartimentado no tratamento de resíduos sólidos orgânicos com baixa concentração de sólidos. O reator anaeróbio compartimentado possuía capacidade unitária de 2.200 litros, era dividido em seis câmaras de iguais dimensões e foi operado com tempo de retenção de sólidos de 90 dias. Os resíduos sólidos orgânicos utilizados para alimentação do reator eram constituídos de resíduos sólidos vegetais e de lodo de esgoto sanitário na proporção de 80% e 20%, respectivamente. A mistura desses dois tipos de resíduos originava o substrato, o qual, após a correção da umidade para 95% (percentagem em massa, era alimentado ao reator. A eficiência de redução de material carbonáceo situou-se em torno de 80%, com carga orgânica aplicada de 9,3 kg R SO m-3 dia-1. A taxa de produção de biogás obtida foi de 5,6 L kg-1substrato (base úmida, com percentagem em volume de 50% de gás metano.The object of this study was to evaluate the use of a compartmented anaerobic reactor to treat organic solid waste with low concentration of solids. The reactor with a total capacity of 2.200 liters, divided into 6 equal chambers, was operated at a solid retention time of 90 days. The organic solids used to feed the reactor were comprised by vegetable residues and sanitary sludge in the proportion 80% and 20% respectively. The mixture of these two types of residues after the humidity correction to 95% (percentage by weight was used to feed the reactor. The removal efficiency of carbonaceous material was approximately 80% at an organic loading of 9.3 kg residual organic solids m-3 d-1. The rate of biogas production was 5.6 L kg-1substrate (wet weight with a methane concentration of 50% by volume.

Maximising municipal solid waste--legume trimming residue mixture degradation in composting by control parameters optimization.

Science.gov (United States)

Cabeza, I O; López, R; Ruiz-Montoya, M; Díaz, M J

2013-10-15

Composting is one of the most successful biological processes for the treatment of the residues enriched in putrescible materials. The optimization of parameters which have an influence on the stability of the products is necessary in order to maximize recycling and recovery of waste components. The influence of the composting process parameters (aeration, moisture, C/N ratio, and time) on the stability parameters (organic matter, N-losses, chemical oxygen demand, nitrate, biodegradability coefficient) of the compost was studied. The composting experiment was carried out using Municipal Solid Waste (MSW) and Legume Trimming Residues (LTR) in 200 L isolated acrylic barrels following a Box-Behnken central composite experimental design. Second-order polynomial models were found for each of the studied compost stability parameter, which accurately described the relationship between the parameters. The differences among the experimental values and those estimated by using the equations never exceeded 10% of the former. Results of the modelling showed that excluding the time, the C/N ratio is the strongest variable influencing almost all the stability parameters studied in this case, with the exception of N-losses which is strongly dependent on moisture. Moreover, an optimized ratio MSW/LTR of 1/1 (w/w), moisture content in the range of 40-55% and moderate to low aeration rate (0.05-0.175 Lair kg(-)(1) min(-1)) is recommended to maximise degradation and to obtain a stable product during co-composting of MSW and LTR. Copyright © 2013 Elsevier Ltd. All rights reserved.

Decree 135/999 establishing legal norms for the management of solid waste in hospitals

International Nuclear Information System (INIS)

1999-01-01

Presently ordinance regulation norms settle down on the hospital solid residuals. A definition of solid residuals, contaminated, common, the transport, treatment,installation and integral handling of the same ones is presented in normative happiness. For finish a classification of a residuals in: infectious, piercing or sharp and special as well as duties and sanctions [es

Cellulase with high β-glucosidase activity by Penicillium oxalicum under solid state fermentation and its use in hydrolysis of cassava residue.

Science.gov (United States)

Su, Lin-Hui; Zhao, Shuai; Jiang, Sui-Xin; Liao, Xu-Zhong; Duan, Cheng-Jie; Feng, Jia-Xun

2017-02-01

In this study, we investigated cellulase production by Penicillium oxalicum EU2106 under solid-state fermentation (SSF) and its hydrolysis efficiency toward NaOH-H 2 O 2 -pretreated cassava residue (NHCR) produced after bioethanol fermentation. Optimization of SSF cultivation conditions for P. oxalicum EU2106 using a Box-behnken design-based response-surface methodology resulted in maximal cellulase activity of 34.0 ± 2.8 filter-paper units/g dry substrate, exhibiting a ~ twofold increase relative to activities obtained under non-optimized conditions. Furthermore, SSF-derived cellulase converted 94.3 ± 1.5% of NHCR cellulose into glucose within 96 h. Interestingly, P. oxalicum EU2106 produced higher β-glucosidase activity under SSF conditions than that under submerged-state fermentation conditions, resulting in the elimination of cellobiose inhibition during the early stages of NHCR cellulose hydrolysis. Overall, this work provided an alternative for a potential cellulase source and a preferred option for cassava residue biotechnological application.

Comets as parent bodies of CI1 carbonaceous meteorites and possible habitats of ice-microbes

Science.gov (United States)

Wickramasinghe, N. Chandra; Wickramasinghe, Janaki T.; Wallis, Jamie; Hoover, Richard B.; Rozanov, Alexei Y.

2011-10-01

Recent studies of comets and cometary dust have confirmed the presence of biologically relevant organic molecules along with clay minerals and water ice. It is also now well established by deuterium/hydrogen ratios that the CI1 carbonaceous meteorites contain indigenous extraterrestrial water. The evidence of extensive aqueous alteration of the minerals in these meteorites led to the hypothesis that water-bearing asteroids or comets represent the parent bodies of the CI1 (and perhaps CM2) carbonaceous meteorites. These meteorites have also been shown to possess a diverse array of complex organics and chiral and morphological biomarkers. Stable isotope studies by numerous independent investigators have conclusively established that the complex organics found in these meteorites are both indigenous and extraterrestrial in nature. Although the origin of these organics is still unknown, some researchers have suggested that they originated by unknown abiotic mechanisms and may have played a role in the delivery of chiral biomolecules and the origin of life on Early Earth. In this paper we review these results and investigate the thermal history of comets. We show that permanent as well as transient domains of liquid water can be maintained on a comet under a plausible set of assumptions. With each perihelion passage of a comet volatiles are preferentially released, and during millions of such passages the comet could shed crustal debris that may survive transit through the Earth's atmosphere as a carbonaceous meteorite. We review the current state of knowledge of comets and carbonaceous meteorites. We also present the results of recent studies on the long-term viability of terrestrial ice-microbiota encased in ancient glacial ice and permafrost. We suggest that the conditions which have been observed to prevail on many comets do not preclude either survivability (or even the active metabolism and growth) of many types of eukaryotic and prokaryotic microbial

Comets as Parent Bodies of CI1 Carbonaceous Meteorites and Possible Habitats of Ice-Microbiota

Science.gov (United States)

Wickramasinghe, N. Chandra; Wallis, Daryl H.; Rozanov, Alexei Yu.; Hoover, Richard B.

2011-01-01

Recent studies of comets and cometary dust have confirmed the presence of biologically relevant organic molecules along with clay minerals and water ice. It is also now well established by deuterium/hydrogen ratios that the CI1 carbonaceous meteorites contain indigenous extraterrestrial water. The evidence of extensive aqueous alteration of the minerals in these meteorites led to the hypothesis that water-bearing asteroids or comets represent the parent bodies of the CI1 (and perhaps CM2) carbonaceous meteorites. These meteorites have also been shown to possess a diverse array of complex organics and chiral and morphological biomarkers. Stable isotope studies by numerous independent investigators have conclusively established that the complex organics found in these meteorites are both indigenous and extraterrestrial in nature. Although the origin of these organics is still unknown, some researchers have suggested that they originated by unknown abiotic mechanisms and may have played a role in the delivery of chiral biomolecules and the origin of life on Early Earth. In this paper we review these results and investigate the thermal history of comets. We show that permanent as well as transient domains of liquid water can be maintained on a comet under a plausible set of assumptions. With each perihelion passage of a comet volatiles are preferentially released, and during millions of such passages the comet could shed crustal debris that may survive transit through the Earth s atmosphere as a carbonaceous meteorite. We review the current state of knowledge of comets and carbonaceous meteorites. We also present the results of recent studies on the long-term viability of terrestrial ice-microbiota encased in ancient glacial ice and permafrost. We suggest that the conditions which have been observed to prevail on many comets do not preclude either survivability (or even the active metabolism and growth) of many types of eukaryotic and prokaryotic microbial

The mercury species and their association with carbonaceous compositions, bromine and iodine in PM2.5 in Shanghai.

Science.gov (United States)

Duan, Lian; Xiu, Guangli; Feng, Ling; Cheng, Na; Wang, Chenggang

2016-03-01

PM2.5 samples were collected in south Shanghai from November 2013 to October 2014. The species of particulate bounded mercury (PBM), including hydrochloric soluble particle-phase mercury (HPM), element soluble particle-phase mercury (EPM) and residual soluble particle-phase mercury (RPM), were determined in PM2.5. The chemical composition of PM2.5 including organic carbon (OC) and elemental carbon (EC), total bromine and iodine were also analyzed. The results showed that the annual average concentration of PBM was 0.30 ± 0.31 ng m(-3) and 0.34 ± 0.32 ng m(-3) in winter, 0.31 ± 0.19 ng m(-3) in spring, 0.30 ± 0.45 ng m(-3) in fall and 0.28 ± 0.17 ng m(-3) in summer. HPM took the highest fraction 51.2% in PBM, followed by RPM 27.7% and EPM 21.1%. EC positively correlated to particle mercury, especially in winter (r = 0.70), the same for OC in winter (r = 0.72), which indicated that the carbonaceous composition may affect the transformation of Hg in the atmosphere. Mercury species showed different correlations with bromine and iodine in the four seasons. The strongest correlation between bromine, iodine and mercury was found in spring and fall, respectively. Bromine showed the stronger correlation with total mercury and speciated particle mercury than iodine. In addition, the days were classified into haze and non-haze days based on the visibility and relative humidity, while the ratio of HPM in haze days was much higher than that in non-haze days. EC strongly correlated with PBM during haze and non-haze days while OC only positively correlated with PBM in non-haze days, this may indicate that the different carbonaceous part may affect PBM differently. Copyright © 2015 Elsevier Ltd. All rights reserved.

Report compiled by Research Center for Carbonaceous Resources, Institute for Chemical Reaction Science, Tohoku University; Tohoku Daigaku Hanno Kagaku Kenkyusho tanso shigen hanno kenkyu center hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-04-01

The Research Center for Carbonaceous Resources was established in April 1991 for the purpose of developing a comprehensive process for converting carbonaceous resources into clean fuels or into materials equipped with advanced functions. In this report, the track records etc. of the center are introduced. Under study in the conversion process research department is the organization of a comprehensive coal conversion process which will be a combination of solvent extraction, catalytic decomposition, and catalytic gasification, whose goal is to convert coal in a clean way at high efficiency. Under study in the conversion catalyst research department are the development of a coal denitrogenation method, development of a low-temperature gasification method by use of inexpensive catalysts, synthesis of C{sub 2} hydrocarbons in a methane/carbon dioxide reaction, etc. Other endeavors under way involve the designing and development of new organic materials such as new carbon materials and a study of the foundation on which such efforts stand, that is, the study of the control of reactions between solids. Furthermore, in the study of interfacial reaction control, the contact gasification of coal, brown coal ion exchange capacity and surface conditions, carbonization of cation exchanged brown coal, etc., are being developed. (NEDO)

Sources of carbonaceous aerosol in the Amazon basin

Directory of Open Access Journals (Sweden)

S. Gilardoni

2011-03-01

Full Text Available The quantification of sources of carbonaceous aerosol is important to understand their atmospheric concentrations and regulating processes and to study possible effects on climate and air quality, in addition to develop mitigation strategies.

In the framework of the European Integrated Project on Aerosol Cloud Climate Interactions (EUCAARI fine (D_p < 2.5 μm and coarse (2.5 μm < D_p <10 μm aerosol particles were sampled from February to June (wet season and from August to September (dry season 2008 in the central Amazon basin. The mass of fine particles averaged 2.4 μg m⁻³ during the wet season and 4.2 μg m⁻³ during the dry season. The average coarse aerosol mass concentration during wet and dry periods was 7.9 and 7.6 μg m⁻³, respectively. The overall chemical composition of fine and coarse mass did not show any seasonality with the largest fraction of fine and coarse aerosol mass explained by organic carbon (OC; the average OC to mass ratio was 0.4 and 0.6 in fine and coarse aerosol modes, respectively. The mass absorbing cross section of soot was determined by comparison of elemental carbon and light absorption coefficient measurements and it was equal to 4.7 m² g⁻¹ at 637 nm. Carbon aerosol sources were identified by Positive Matrix Factorization (PMF analysis of thermograms: 44% of fine total carbon mass was assigned to biomass burning, 43% to secondary organic aerosol (SOA, and 13% to volatile species that are difficult to apportion. In the coarse mode, primary biogenic aerosol particles (PBAP dominated the carbonaceous aerosol mass. The results confirmed the importance of PBAP in forested areas.

The source apportionment results were employed to evaluate the ability of global chemistry transport models to simulate carbonaceous aerosol sources in a regional tropical background site. The comparison showed an overestimation

Carbon isotope analysis of carbonaceous compounds in Puget Sound and Lake Washington

International Nuclear Information System (INIS)

Swanson, J.R.

1980-01-01

A new method has been developed and tested for determining chronological profiles of organic pollutants. This method, Carbon Isotope Analysis (CIA), involves measurements of 12 C, 13 C and 14 C in carbonaceous compounds found in layers of sediment. Lipids, total aliphatic hydrocarbons (TAHs) and polycyclic aromatic hydrocarbons (PAHs) are separated from kg quantities of sediment. Large Soxhlet extractors are used to remove the extractable organics, using ultra-pure benzene-methanol solution and having an extraction efficiency of about 86% for compounds with boiling points higher than n-tetradecane (n-C 14 ). The basic steps in compound separation include freeze-drying, extraction, fractionation, column chromatography and evaporation. Isolating the TAH and PAH fractions is accomplished by eluting samples from Sephadex and alumina/silica-gel columns. The amount of each fraction recovered is determined by converting the hydrocarbons to carbon dioxide and measuring this gas manometrically. Variations in 12 C and 13 C abundances for carbonaceous compounds are primarily due to thermodynamic, photosynthetic and metabolic fractionation processes. Thus, the source of a particular organic compound can often be determined by measuring its 13 C/ 12 C ratio. Combining the information from both the 13 C analysis and 14 C analysis makes source identification more certain. In addition, this investigation reviews carbon isotopic data and carbon cycling and analyzes organic pollution in two limited ecosystems (Puget Sound and Lake Washington). Specifically, distinct carbonaceous species are analyzed for pollution in sediments of Lake Washington, Elliott Bay, Commencement Bay, central Puget Sound and northern Puget Sound near the Cherry Point oil refineries

Characterization and performance of carbonaceous materials obtained from exhausted sludges for the anaerobic biodecolorization of the azo dye Acid Orange II

Energy Technology Data Exchange (ETDEWEB)

Athalathil, S.; Stüber, F.; Bengoa, C.; Font, J. [Departament d’Enginyeria Quimica, ETSEQ, Universitat Rovira i Virgili, Av. Paisos Catalans 26, 43007 Tarragona, Catalunya (Spain); Fortuny, A. [Departament d’Enginyeria Quimica, EPSEVG, Universitat Politecnica de Catalunya, Av. Victor Balaguer s/n, 08800 Vilanova i la Geltru, Catalunya (Spain); Fabregat, A., E-mail: azael.fabregat@urv.cat [Departament d’Enginyeria Quimica, ETSEQ, Universitat Rovira i Virgili, Av. Paisos Catalans 26, 43007 Tarragona, Catalunya (Spain)

2014-02-01

Graphical abstract: - Highlights: • Carbonaceous materials were prepared from exhausted sludge materials. • High surface area and good physicochemical properties were achieved. • Utilization of waste sludge materials and mixed anaerobic cultures were used in a continuous anaerobic UPBR system (upflow packed bed biological reactor). • Effective treatment of dye contaminated wastewater in a cheapest and environmental friendly method was demonstrated. - Abstract: This work presents the preliminary study of new carbonaceous materials (CMs) obtained from exhausted sludge, their use in the heterogeneous anaerobic process of biodecolorization of azo dyes and the comparison of their performance with one commercial active carbon. The preparation of carbonaceous materials was conducted through chemical activation and carbonization. Chemical activation was carried out through impregnation of sludge-exhausted materials with ZnCl{sub 2} and the activation by means of carbonization at different temperatures (400, 600 and 800 °C). Their physicochemical and surface characteristics were also investigated. Sludge based carbonaceous (SBC) materials SBC400, SBC600 and SBC800 present values of 13.0, 111.3 and 202.0 m{sup 2}/g of surface area. Biodecolorization levels of 76% were achieved for SBC600 and 86% for SBC800 at space time (τ) of 1.0 min, similar to that obtained with commercial activated carbons in the continuous anaerobic up-flow packed bed reactor (UPBR). The experimental data fit well to the first order kinetic model and equilibrium data are well represented by the Langmuir isotherm model. Carbonaceous materials show high level of biodecolorization even at very short space times. Results indicate that carbonaceous materials prepared from sludge-exhausted materials have outstanding textural properties and significant degradation capacity for treating textile effluents.

Energy from briquettes produced from remains of urban solid residues and wood of Eucalyptus grandis; Energia de briquetes produzidos com rejeitos de residuos solidos urbanos e madeira de Eucalyptus grandis

Energy Technology Data Exchange (ETDEWEB)

Goncalves, Jose E.; Leao, Alcides L. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Botucatu, SP (Brazil). Dept. de Ciencias Ambientais], emails: evaristo@fca.unesp.br, alcidesleao@fca.unesp.br; Sartori, Maria M.P. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Bauru, SP (Brazil). Dept. de Engenharia de Producao], email: msartori@btu.flash.tv.br

2009-07-01

The incentive for consumption and production in large quantity in modern society generates enormous amounts of urban solid residues in the form of municipal solid waste (MSW). With the intention of reducing these residues of the municipal waste tips and to generate energy, briquettes with mixtures of MSW and residues of Eucalyptus grandis were produced. The briquettes were manufactured with 0, 5, 10, 15, 20 and 25% of MSW in the mixture with wood waste and 12% of moisture content. The analyzed parameters used to choose the best treatments were combustion analysis versus ash content, mechanical strength and energy content. The briquettes up to 10% of MSW showed low resistance, and above 15% showed large increase in ash content. Therefore, the treatment that fulfilled the requirements for combustion versus ash content and mechanical resistance was of at least 15% of MSW, since the source of the ash is unidentified. Considering the net energy content, the best treatment was 25% of MSW, with 17,175 kJ kg{sup -1}. Nevertheless, it is strongly advised that further studies related to gas emissions are necessary. (author)

Acid/base bifunctional carbonaceous nanomaterial with large surface area: Preparation, characterization, and adsorption properties for cationic and anionic compounds

Energy Technology Data Exchange (ETDEWEB)

Li, Kai; Ma, Chun–Fang; Ling, Yuan; Li, Meng [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Gao, Qiang, E-mail: gaoqiang@cug.edu.cn [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China); Engineering Research Center of Nano-Geo Materials of Ministry of Education, China University of Geosciences, Wuhan 430074 (China); Luo, Wen–Jun, E-mail: heartnohome@yahoo.com.cn [Department of Chemistry, Faculty of Material Science and Chemistry, China University of Geosciences, Wuhan 430074 (China)

2015-07-15

Nanostructured carbonaceous materials are extremely important in the nano field, yet developing simple, mild, and “green” methods that can make such materials possess large surface area and rich functional groups on their surfaces still remains a considerable challenge. Herein, a one-pot and environment-friendly method, i.e., thermal treatment (180 °C; 18 h) of water mixed with glucose and chitosan (CTS), has been proposed. The resultant carbonaceous nanomaterials were characterized by field emitting scanning electron microscope, N{sub 2} adsorption/desorption, Fourier transform infrared spectroscope, X-ray photoelectron spectroscopy, and zeta-potential analysis. It was found that, in contrast to the conventional hydrothermally carbonized product from pure glucose, with low surface area (9.3 m{sup 2} g{sup −1}) and pore volume (0.016 cm{sup 3} g{sup −1}), the CTS-added carbonaceous products showed satisfactory textural parameters (surface area and pore volume up to 254 m{sup 2} g{sup −1} and 0.701 cm{sup 3} g{sup −1}, respectively). Moreover, it was also interestingly found that these CTS-added carbonaceous products possessed both acidic (–COOH) and basic (–NH{sub 2}) groups on their surfaces. Taking the advantages of large surface area and –COOH/–NH{sub 2} bifunctional surface, the carbonaceous nanomaterials exhibited excellent performance for adsorptions of cationic compound (i.e., methylene blue) at pH 10 and anionic compound (i.e., acid red 18) at pH 2, respectively. This work not only provides a simple and green route to prepare acid/base bifunctional carbonaceous nanomaterials with large surface area but also well demonstrates their potential for application in adsorption. - Highlights: • A simple and green method was proposed to prepare carbon nanomaterials. • The carbon product showed acid/base bifunctional surface with large surface area. • The carbon material could efficiently adsorb both cationic and anionic compounds.

Inner Surface Chirality of Single-Handed Twisted Carbonaceous Tubular Nanoribbons.

Science.gov (United States)

Liu, Dan; Li, Baozong; Guo, Yongmin; Li, Yi; Yang, Yonggang

2015-11-01

Single-handed twisted 4,4'-biphenylene-bridged polybissilsesquioxane tubular nanoribbons and single-layered nanoribbons were prepared by tuning the water/ethanol volume ratio in the reaction mixture at pH = 11.6 through a supramolecular templating approach. The single-layered nanoribbons were formed by shrinking tubular nanoribbons after the removal of the templates. In addition, solvent-induced handedness inversion was achieved. The handedness of the polybissilsesquioxanes could be controlled by changing the ethanol/water volume ratio in the reaction mixture. After carbonization at 900 °C for 4.0 h and removal of silica, single-handed twisted carbonaceous tubular nanoribbons and single-layered nanoribbons with micropores in the walls were obtained. X-ray diffraction and Raman spectroscopy analyses indicated that the carbon is predominantly amorphous. The circular dichroism spectra show that the twisted tubular nanoribbons exhibit optical activity, while the twisted single-layered nanoribbons do not. The results shown here indicate that chirality is transferred from the organic self-assemblies to the inner surfaces of the 4,4'-biphenylene-bridged polybissilsesquioxane tubular nanoribbons and subsequently to those of the carbonaceous tubular nanoribbons. © 2015 Wiley Periodicals, Inc.

Carbonaceous matter in the Pomozhan deposit

Energy Technology Data Exchange (ETDEWEB)

Piatek, G

1979-01-01

Carbonaceous matter (CM), encountered in the Pomozhan deposit, is coordinate to dolomitic-illitic clay, filling caverns in ore-bearing dolomites. The CM represents a disperse mass with particle sizes up to 2 mm, having a color from dark brown to black. The reflectivity (0.35-0.42%) and classification assignment of the CM to macerals of the vitrinite or dopplerinite group were determined by micropetrographic methods. CM belonging to the type of humic coals, transitional from brown to bituminous coals is an epigenetic formation. Its accumulation in the regions of the Ol'kush ore deposits occurred in the Triassic-Cretaceous or Cenozoic interval. Liassic coal of the Zavertse region or Helvetian coal of Khomentuv and Tarnobzheg could be the source of the CM.

Instructive for radioactive solid waste management

International Nuclear Information System (INIS)

Mora Rodriguez, Patricia

2014-01-01

An instructive is established for the management system of radioactive solid residues waste of the Universidad de Costa Rica, ensuring the collection, segregation, storage and disposal of waste. The radioactive solid waste have been segregated and transferred according to features and provisions of the Universidad de Costa Rica and CICANUM [es

Magnetically Enhanced Solid-Liquid Separation

Science.gov (United States)

Rey, C. M.; Keller, K.; Fuchs, B.

2005-07-01

DuPont is developing an entirely new method of solid-liquid filtration involving the use of magnetic fields and magnetic field gradients. The new hybrid process, entitled Magnetically Enhanced Solid-Liquid Separation (MESLS), is designed to improve the de-watering kinetics and reduce the residual moisture content of solid particulates mechanically separated from liquid slurries. Gravitation, pressure, temperature, centrifugation, and fluid dynamics have dictated traditional solid-liquid separation for the past 50 years. The introduction of an external field (i.e. the magnetic field) offers the promise to manipulate particle behavior in an entirely new manner, which leads to increased process efficiency. Traditional solid-liquid separation typically consists of two primary steps. The first is a mechanical step in which the solid particulate is separated from the liquid using e.g. gas pressure through a filter membrane, centrifugation, etc. The second step is a thermal drying process, which is required due to imperfect mechanical separation. The thermal drying process is over 100-200 times less energy efficient than the mechanical step. Since enormous volumes of materials are processed each year, more efficient mechanical solid-liquid separations can be leveraged into dramatic reductions in overall energy consumption by reducing downstream drying requirements have a tremendous impact on energy consumption. Using DuPont's MESLS process, initial test results showed four very important effects of the magnetic field on the solid-liquid filtration process: 1) reduction of the time to reach gas breakthrough, 2) less loss of solid into the filtrate, 3) reduction of the (solids) residual moisture content, and 4) acceleration of the de-watering kinetics. These test results and their potential impact on future commercial solid-liquid filtration is discussed. New applications can be found in mining, chemical and bioprocesses.

Hanford tank residual waste - Contaminant source terms and release models

International Nuclear Information System (INIS)

Deutsch, William J.; Cantrell, Kirk J.; Krupka, Kenneth M.; Lindberg, Michael L.; Jeffery Serne, R.

2011-01-01

Highlights: → Residual waste from five Hanford spent fuel process storage tanks was evaluated. → Gibbsite is a common mineral in tanks with high Al concentrations. → Non-crystalline U-Na-C-O-P ± H phases are common in the U-rich residual. → Iron oxides/hydroxides have been identified in all residual waste samples. → Uranium release is highly dependent on waste and leachant compositions. - Abstract: Residual waste is expected to be left in 177 underground storage tanks after closure at the US Department of Energy's Hanford Site in Washington State, USA. In the long term, the residual wastes may represent a potential source of contamination to the subsurface environment. Residual materials that cannot be completely removed during the tank closure process are being studied to identify and characterize the solid phases and estimate the release of contaminants from these solids to water that might enter the closed tanks in the future. As of the end of 2009, residual waste from five tanks has been evaluated. Residual wastes from adjacent tanks C-202 and C-203 have high U concentrations of 24 and 59 wt.%, respectively, while residual wastes from nearby tanks C-103 and C-106 have low U concentrations of 0.4 and 0.03 wt.%, respectively. Aluminum concentrations are high (8.2-29.1 wt.%) in some tanks (C-103, C-106, and S-112) and relatively low ( 2 -saturated solution, or a CaCO 3 -saturated water. Uranium release concentrations are highly dependent on waste and leachant compositions with dissolved U concentrations one or two orders of magnitude higher in the tests with high U residual wastes, and also higher when leached with the CaCO 3 -saturated solution than with the Ca(OH) 2 -saturated solution. Technetium leachability is not as strongly dependent on the concentration of Tc in the waste, and it appears to be slightly more leachable by the Ca(OH) 2 -saturated solution than by the CaCO 3 -saturated solution. In general, Tc is much less leachable (<10 wt.% of the

The chemical structure of the insoluble organic matter from carbonaceous meteorites

Science.gov (United States)

Derenne, S.; Robert, F.

2008-09-01

Carbonaceous chondrites are the most primitive objects of the solar system. They contain substantial amounts of carbon (up to 3%), mostly occurring in macromolecular insoluble organic matter (IOM). This IOM is generally considered as a record of interstellar synthesis and may contain precursors of prebiotic molecules possibly deposited on earth by meteoritic bombardments. For these reasons, chondritic IOM has been raising interest for long and it is therefore of special interest to decipher its chemical structure. It is now well established that the chemical structure of this macromolecular material is based on aromatic moieties linked by short aliphatic chains and comprising substantial amounts of heteroatoms. However, its precise chemical structure could only be recently specified. The aim of this presentation is to propose a molecular model for the chemical structure of IOM isolated from non-metamorphosed carbonaceous chondrites. This model is derived from a large set of data obtained through a combination of techniques including various spectrocopies, high resolution transmission electron microscopy (HRTEM) and chemical and thermal degradations. Cosmochemical implications of such a structure will also be discussed.

Effects of day-of-week trends and vehicle types on PM{sub 2.5}-bounded carbonaceous compositions

Energy Technology Data Exchange (ETDEWEB)

Pongpiachan, Siwatt, E-mail: pongpiajun@gmail.com [NIDA Center for Research & Development of Disaster Prevention & Management, School of Social and Environmental Development, National Institute of Development Administration (NIDA), 118 Moo 3, Sereethai Road, Klong-Chan, Bangkapi, Bangkok 10240 (Thailand); SKLLQG, Institute of Earth Environment, Chinese Academy of Sciences (IEECAS), Xi' an 710075 (China); Kositanont, Charnwit [Department of Microbiology, Faculty of Sciences, Chulalongkorn University, Bangkok 10330 (Thailand); Palakun, Jittree [Faculty of Education, Valaya Alongkorn Rajabhat University under the Royal Patronage (VRU), No.1 Moo 20, Phaholyothin Road, Klong luang, Pathumthani 13180 (Thailand); Liu, Suixin; Ho, Kin Fai; Cao, Junji [SKLLQG, Institute of Earth Environment, Chinese Academy of Sciences (IEECAS), Xi' an 710075 (China)

2015-11-01

Carbonaceous compositions of PM{sub 2.5} were measured in the heart of Bangkok from 17th November 2010 to 19th January 2012, and a data set of 94 samples was constructed. Effects of day-of-week trends and vehicle types on PM{sub 2.5}-bound TC, OC, and EC were carefully investigated. In this study, OC was the most important contributor to the total PM{sub 2.5} mass concentration. The average PM{sub 2.5}-bound OC content measured at CHAOS (18.8 ± 9.18 μg m{sup −3}) was approximately 11 times higher than at Chaumont, Switzerland (1.7 μg m{sup −3}), but approximately five times lower than at Xi'an, China (93.0 μg m{sup −3}). The application of diagnostic binary ratios of OC/EC and estimations of secondary organic carbon (SOC) coupled with autocorrelation plots (Box and Jenkins) highlight the enhanced impacts of traffic emissions, especially from diesel vehicles, on PM{sub 2.5}-bound carbonaceous compositions on weekdays relative to weekends. Hierarchical cluster analysis (HCA) coupled with principal component analysis (PCA) underline the importance of diesel emissions as the primary contributors of carbonaceous aerosols, particularly during weekdays. - Highlights: • Traffic emissions play an important role in governing OC and EC during weekdays. • Time series analysis shows the existence of day-of-week trends of OC and EC. • Diesel vehicles are the main contributors of carbonaceous compositions.

Sugar and Sugar Derivatives in Residues Produced from the UV Irradiation of Astrophysical Ice Analogs

Science.gov (United States)

Nuevo, M.; Sandford, S. A.; Cooper, G.

2016-01-01

A large variety and number of organic compounds of prebiotic interest are known to be present in carbonaceous chondrites. Among them, one sugar (dihydroxyacetone) as well as several sugar acids, sugar alcohols, and other sugar derivatives have been reported in the Murchison and Murray meteorites. Their presence, along with amino acids, amphiphiles, and nucleobases strongly suggests that molecules essential to life can form abiotically under astrophysical conditions. This hypothesis is supported by laboratory studies on the formation of complex organic molecules from the ultraviolet (UV) irradiation of simulated astrophysical ice mixtures consisting of H2O, CO, CO2, CH3OH, CH4, NH3, etc., at low temperature. In the past 15 years, these studies have shown that the organic residues recovered at room temperature contain amino acids, amphiphiles, nucleobases, as well as other complex organics. However, no systematic search for the presence of sugars and sugar derivatives in laboratory residues have been reported to date, despite the fact that those compounds are of primary prebiotic significance. Indeed, only small (up to 3 carbon atoms) sugar derivatives including glycerol and glyceric acid have been detected in residues so far.

Acid transformation of bauxite residue: Conversion of its alkaline characteristics

OpenAIRE

Kong, X.; Li, M.; Xue, S.; Hartley, W.; Chen, C.; Wu, C.; Li, X.; Li, Y.

2016-01-01

Bauxite residue (BR) is a highly alkaline solid hazardous waste produced from bauxite processing for alumina production. Alkaline transformation appears to reduce the environmental risk of bauxite residue disposal areas (BRDAs) whilst potentially providing opportunities for the sustainable reuse and on-going management of BR. Mineral acids, a novel citric acid and a hybrid combination of acid-gypsum treatments were investigated for their potential to reduce residue pH and total alkalinity and...

Atmospheric carbonaceous aerosols from Indo-Gangetic Plain and Central Himalaya: impact of anthropogenic sources.

Science.gov (United States)

Ram, Kirpa; Sarin, M M

2015-01-15

In the present-day scenario of growing anthropogenic activities, carbonaceous aerosols contribute significantly (∼20-70%) to the total atmospheric particulate matter mass and, thus, have immense potential to influence the Earth's radiation budget and climate on a regional to global scale. In addition, formation of secondary organic aerosols is being increasingly recognized as an important process in contributing to the air-pollution and poor visibility over urban regions. It is, thus, essential to study atmospheric concentrations of carbonaceous species (EC, OC and WSOC), their mixing state and absorption properties on a regional scale. This paper presents the comprehensive data on emission sources, chemical characteristics and optical properties of carbonaceous aerosols from selected urban sites in the Indo-Gangetic Plain (IGP) and from a high-altitude location in the central Himalaya. The mass concentrations of OC, EC and WSOC exhibit large spatio-temporal variability in the IGP. This is attributed to seasonally varying emissions from post-harvest agricultural-waste burning, their source strength, boundary layer dynamics and secondary aerosol formation. The high concentrations of OC and SO4(2-), and their characteristic high mass scattering efficiency, contribute significantly to the aerosol optical depth and scattering coefficient. This has implications to the assessment of single scattering albedo and aerosol radiative forcing on a regional scale. Copyright © 2014 Elsevier Ltd. All rights reserved.

Distinct Purine Distribution in Carbonaceous Chondrites

Science.gov (United States)

Callahan, Michael P.; Smith, Karen E.; Cleaves, Henderson J.; Ruzicka, Josef; Stern, Jennifer C.; Glavin, Daniel P.; House, Christopher H.; Dworkin, Jason P.

2011-01-01

Carbonaceous chondrite meteorites are known to contain a diverse suite of organic compounds, many of which are essential components of biochemistry. Amino acids, which are the monomers of proteins, have been extensively studied in such meteorites (e.g. Botta and Bada 2002; Pizzarello et aI., 2006). The origin of amino acids in meteorites has been firmly established as extraterrestrial based on their detection typically as racemic mixtures of amino acids, the presence of many non-protein amino acids, and non-terrestrial values for compound-specific deuterium, carbon, and nitrogen isotopic measurements. In contrast to amino acids, nucleobases in meteorites have been far less studied. Nucleobases are substituted one-ring (pyrimidine) or two-ring (purine) nitrogen heterocyclic compounds and serve as the information carriers of nucleic acids and in numerous coenzymes. All of the purines (adenine, guanine, hypoxanthine, and xanthine) and pyrimidines (uracil) previously reported in meteorites are biologically common and could be interpreted as the result of terrestrial contamination (e.g. van del' Velden and Schwartz, 1974.) Unlike other meteoritic organics, there have been no observations of stochastic molecular diversity of purines and pyrimidines in meteorites, which has been a criterion for establishing extraterrestrial origin. Maltins et al. (2008) performed compound-specific stable carbon isotope measurements for uracil and xanthine in the Murchison meteorite. They assigned a non-terrestrial origin for these nucleobases; however, the possibility that interfering indigenous molecules (e.g. carboxylic acids) contributed to the 13C-enriched isotope values for these nucleobases cannot be completely ruled out. Thus, the origin of these meteoritic nucleobases has never been established unequivocally. Here we report on our investigation of extracts of II different carbonaceous chondrites covering various petrographic types (Cl, CM, and CR) and degrees of aqueous alteration

Characterization of Chiral Carbonaceous Nanotubes Prepared from Four Coiled Tubular 4,4'-biphenylene-silica Nanoribbons

Directory of Open Access Journals (Sweden)

Shuwei Lin

2014-04-01

Full Text Available Four dipeptides derived from phenylalanine were synthesized, which can self-assemble into twisted nanoribbon in deionized water. The handedness of the organic self-assemblies was controlled by the chirality of the phenylalanine at the terminals. Coiled 4,4'-biphenylene bridged polybissilsesquioxane tubular nanoribbons were prepared using the organic self-assemblies as the templates. The circular dichroism spectra indicated that the biphenylene rings preferred to twist in one-handedness within the walls of the samples. After carbonization and removal of silica, single-handed coiled carbonaceous tubular nanoribbons were obtained. The Raman spectra indicated that the carbon was amorphous. The diffuse reflectance circular dichroism spectra indicated the tubular carbonaceous nanoribbons exhibited optical activity.

Application of alkaline solid residue of electric arc furnace dust for neutralization/purification of electroplating wastewaters.

Science.gov (United States)

Elez, Loris; Orescanin, Visnja; Sofilic, Tahir; Mikulic, Nenad; Ruk, Damir

2008-10-01

The purpose of this work was development of an appropriate procedure for the neutralization/purification of electroplating wastewater (EWW) with alkaline solid residue (ASR) by-product of the alkaline extraction of zinc and lead from electric arc furnace dust (EAFD). Removal efficiency of ASR at optimum purification conditions (pH 8 and mixing time; 20 minutes) for the elements Pb, Cr (VI), Cr (III), Fe, Ni, Cu and Zn were 94.92%, 97.58%, 99.59%, 99.48%, 97.25% and 99.97%, respectively. The concentrations of all elements in the purified wastewater were significantly lower in relation to the upper permissible limit for wastewaters suitable for discharge into the environment. The remaining waste mud was regenerated in the strong alkaline medium and successfully applied once again for the neutralization/purification of EWW. Removal efficiencies of heavy metals accomplished with regenerated waste mud were comparable to these achieved by original ASR. Elemental concentrations in the leachates of the waste mud were in accordance with regulated values.

Solar-Radiation Heating as a Possible Heat Source for Dehydration of Hydrous Carbonaceous Chondrites

Science.gov (United States)

Nakamura, T.; Golabek, G.; Ohtsuka, K.; Matsuoka, M.

2017-07-01

We have calculated time-dependent temperature profiles of near surface layers of primitive Near Sun Asteroid (3200) Phaethon and found that solar radiation heating is a possible heat source for dehydration of carbonaceous chondrites.

All conducting polymer electrodes for asymmetric solid-state supercapacitors

KAUST Repository

Kurra, Narendra

2015-02-16

In this study, we report the fabrication of solid-state asymmetric supercapacitors (ASCs) based on conducting polymer electrodes on a plastic substrate. Nanostructured conducting polymers of poly(3,4-ethylenedioxythiophene), PEDOT, and polyaniline (PANI) are deposited electrochemically over Au-coated polyethylene naphthalate (PEN) plastic substrates. Due to the electron donating nature of the oxygen groups in the PEDOT, reduction potentials are higher, allowing it to be used as a negative electrode material. In addition, the high stability of PEDOT in its oxidised state makes it capable to exhibit electrochemical activity in a wide potential window. This can qualify PEDOT to be used as a negative electrode in fabricating asymmetric solid state supercapacitors with PANI as a positive electrode while employing polyvinyl alcohol (PVA)/H2SO4 gel electrolyte. The ASCs exhibit a maximum power density of 2.8 W cm−3 at an energy density of 9 mW h cm−3, which is superior to the carbonaceous and metal oxide based ASC solid state devices. Furthermore, the tandem configuration of asymmetric supercapacitors is shown to be capable of powering a red light emitting diode for about 1 minute after charging for 10 seconds.

Organic Chemistry of Carbonaceous Meteorites

Science.gov (United States)

Cronin, John R.

2001-01-01

Chiral and carbon-isotopic analyses of isovaline have been carried out on numerous samples of the Murchison and one sample of the Murray carbonaceous chondrite. The isovaline was found to be heterogeneous with regard to enantiomeric excess (ee) both between samples and within a single Murchison sample. L-Excesses ranging from 0 to 15% were observed. The isovaline delta(sup 13) C was found to be about +18%. No evidence was obtained suggesting terrestrial contamination in the more abundant L-enantiomer. A correlation was observed between isovaline (also alpha - aminoisobutyric acid) concentration and PCP content of five CM chondrites. It is suggested that isovaline, along with other meteoritic a-methyl amino acids with ee, are of presolar origin. The possible formation of ee in extraterrestrial amino acids by exposure to circularly polarized light or by magnetochiral photochemistry is discussed. Key words: Murchison meteorite, Murray meteorite, amino acids, isovaline, chirality, carbon isotopes, PCP.

Reactions on carbonaceous materials with hydrogenating gases

Energy Technology Data Exchange (ETDEWEB)

Pier, M; Simon, W; Kronig, W

1933-02-08

A process is given for the production of valuable hydrocarbons by treatment of distillable carbonaceous materials with added hydrogenating gases under pressure in contact with catalysts. The process comprises adding to the initial materials before or during the said treatment organic sulphonic acids together with metals of groups 4 to 8 of the periodic system or compounds thereof, or free organic carboxylic acids which when inorganic salts are simultaneously present do not combine therewith to form complex ansolvo acids, or acid salts of strong acids or acid salts of heavy metals, lithium, magnesium, and aluminum, with the exception of aluminum hydrosilicates, or inorganic oxygen containing acids of sulfur or nitrogen or the anhydrides of said inorganic oxygen-containing acids.

Carbonaceous material in fine particulate matter (PM10) of urban areas

International Nuclear Information System (INIS)

Brocco, Domenico; Leonardi, Vittorio; Maso; Marco; Prignani, Patrizia

2006-01-01

Total carbon (TC), elemental carbon (EC) and organic carbon (OC) in the fine particulate matter (PM10) were measured in the urban areas of Rome and Marino (Castelli Romani) by means a thermal method with a non-dispersive infrared detector (NDIR). The results showed that carbonaceous material constitutes 30-40% of the total aerosols in Rome and about 20% in Marino [it

The application of a layer of carbonaceous material to a surface

International Nuclear Information System (INIS)

Holland, L.A.

1981-01-01

A method of applying a carbonaceous material to a surface is described. It consists of exposing the surface to an ionised gas atmosphere generated in a gas consisting substantially of carbon and hydrogen, and applying to the surface through capacitive means an electrical potential which changes in sign at time intervals of between 5 x 10 -9 seconds and 10 -6 seconds. (author)

Results of Characterization and Retrieval Testing on Tank 241-C-110 Heel Solids

Energy Technology Data Exchange (ETDEWEB)

Callaway, William S.

2013-09-30

dissolution tests. Most of the {sup 99}Tc and {sup 137}Cs present in the initial heel solids composites was removed in the water dissolution tests. The estimated activities/weights of {sup 129}I, {sup 234}U, {sup 235}U, {sup 236}U, and {sup 238}U in the dry residual solids were <25% of the weights/activities in the initial composite solids. Gibbsite and nordstrandite [both Al(OH){sub 3}] were the major solid phases identified in the solids remaining after completion of the dissolution tests. Chemical analysis indicated that the residual solids may have contained up to 62 wt% Al(OH){sub 3}. Significant quantities of unidentified phosphate-, iron-, bismuth-, silicon-, and strontium- bearing species were also present in the residual solids. The reference density of gibbsite (and nordstrandite) is 2.42 g/mL. The measured density of the residual solids, 2.65 g/mL, would be a reasonable value for solids containing gibbsite as the major component with minor quantities of other, higher density solids. Sieve analysis indicated that 22.2 wt% of the residual solids were discrete particles >710 μm in size, and 77.8 wt% were particulates <710 μm in size. Light-scattering measurements suggested that nearly all of the <710-μm particulates with diameters >12 μm were weakly bound aggregates of particles with diameters <2 μm. The <710-μm residual solids settled very slowly when dispersed in reagent water. The physical appearance of a suspension containing ≈0.4 vol% of the solids in pure water changed very little over a period of 46.5 hours. It should be noted that the distribution of particle sizes in the residual solids and the observed settling behavior were both strongly influenced by the procedures followed in the dissolution tests.

Hydrogenizing oils, asphalts, etc

Energy Technology Data Exchange (ETDEWEB)

1925-03-14

The hydrogenation of carbonaceous solids in presence of combined sulfur, e.g., sulfides as described in the parent specification is applied to the treatment of rock oils, shale oils, resins, ozokerite, asphalt, and the like, or fractions, residues, or acid sludge or other conversion products thereof, alone or mixed. Preferably the hydrogen or other reducing gas is in excess and under pressure, and is either circuited or led through a series of treatment vessels, hydrogen being added for that used. In an example, residues from American crude oil are passed continuously with hydrogen at 200 atmospheres and 450 to 500/sup 0/C over pressed precipitated cobalt sulfide, the issuing gases being cooled to condense the light oil produced.

Emission factors of carbonaceous particulate matter and polycyclic aromatic hydrocarbons from residential solid fuel combustions

Energy Technology Data Exchange (ETDEWEB)

Shen, Guofeng [Jiangsu Academy of Environmental Science, Nanjing (China). Inst. of Atmospheric Sciences

2014-07-01

Emission inventory is basic for the understanding of environmental behaviors and potential effects of compounds, however, current inventories are often associated with relatively high uncertainties. One important reason is the lack of emission factors, especially for the residential solid fuel combustion in developing countries. In the present study, emission factors of a group of pollutants including particulate matter, organic carbon, elemental carbon (sometimes known as black carbon) and polycyclic aromatic hydrocarbons were measured for a variety of residential solid fuels including coal, crop straw, wood, and biomass pellets in rural China. The study provided a large number of emission factors that can be further used in emission estimation. Composition profiles and isomer ratios were investigated and compared so as to be used in source apportionment. In addition, the present study identified and quantified the influence of factors like fuel moisture, volatile matter on emission performance.

Determination of the torsion angles of alanine and glycine residues of model compounds of spider silk (AGG){sub 10} using solid-state NMR methods

Energy Technology Data Exchange (ETDEWEB)

Ashida, Jun; Ohgo, Kosuke; Komatsu, Kohei; Kubota, Ayumi; Asakura, Tetsuo [Tokyo University of Agriculture and Technology, Department of Biotechnology (Japan)], E-mail: asakura@cc.tuat.ac.jp

2003-02-15

Spiders synthesize several kinds of silk fibers. In the primary structure of spider silk, one of the major ampullate (dragline, frame) silks, spidroin 1, and flagelliform silk (core fibers of adhesive spiral), there are common repeated X-Gly-Gly (X = Ala, Leu, Pro, Tyr, Glu, and Arg) sequences, which are considered to be related to the elastic character of these fibers. In this paper, two dimensional spin diffusion solid-state NMR under off magic angle spinning (OMAS), {sup 13}C chemical shift contour plots, and Rotational Echo DOuble Resonance (REDOR) were applied to determine the torsion angles of one Ala and two kinds of Gly residues in the Ala-Gly-Gly sequence of {sup 13}C=O isotope-labeled (Ala-Gly-Gly){sub 10}. The torsion angles were determined to be ({phi}, {psi}) = (-90 deg., 150 deg.) within an experimental error of {+-}10 deg. for each residue. This conformation is characterized as 3{sub 1} helix which is in agreement with the structure proposed from the X-ray powder diffraction pattern of poly(Ala-Gly-Gly). The 3{sub 1} helix of (Ala-Gly-Gly){sub 10} does not change by formic acid treatment although (Ala-Gly){sub 15} easily changes from the silk I conformation (the structure of Bombyx mori silk fibroin before spinning in the solid state) to silk II conformation (the structure of the silk fiber after spinning) by such treatment. Thus, the 3{sub 1} helix conformation of (Ala-Gly-Gly){sub 10} is considered very stable. Furthermore, the torsion angles of the 16th Leu residue of (Leu-Gly-Gly){sub 10} were also determined as ({phi}, {psi}) = (-90 deg., 150 deg.) and this peptide is also considered to take 3{sub 1} helix conformation.

Distillation of carbonaceous material

Energy Technology Data Exchange (ETDEWEB)

Ainscow, J W.H.

1936-10-03

To recover hydrocarbon products by distillation of carbonaceous material in a plurality of horizontal zones maintained at different temperatures, a retort has a plurality of superimposed (3) retort chambers, the uppermost being in communication at one end with a hopper and at the other end through coupled junction not shown with one end of the next lower chamber, whose opposite end communicates with lowermost chamber, the other end of which has a sealed discharge passage, tank, and conveyor not shown. Each retort chamber has stirring and conveying means consisting of helical blades (2) attached to radial arms on shaft mounted in water cooled bearings and driven through suitably mounted sprocket wheels and chains not shown. Each retort chamber has a gas dome, with pyrometer tube, and off-take connected to a common main opening into a dust eliminator which in turn connects with a plurality of vertical condensation towers of known construction, maintained at different temperatures by means of steam from a superheater not shown situated in one retort chamber. The retort heating gases pass from the furnace via zig-zag, (three) baffles under and around each retort chamber to a flue not shown.

Lithium storage into carbonaceous materials obtained from sugarcane bagasse

International Nuclear Information System (INIS)

Matsubara, Elaine Y.; Lala, Stella M.; Rosolen, Jose Mauricio

2010-01-01

Carbonaceous materials with different structures are prepared by carbonization of sugarcane bagasse. Depending on carbonization conditions, it is possible to obtain soot rich in flakes or in honeycomb-shaped micrometric particles, whose concentration has large influence on lithium storage into electrodes. The soot rich in honeycomb-shaped particles provides the best electrochemical performance, with a reversible specific capacity of 310 mAh g -1 . The results suggest that the sugarcane bagasse can be potentially used in the design of anodic materials for lithium ion batteries. (author)

Process of producing carbonaceous materials; reaction with hydrogen gases

Energy Technology Data Exchange (ETDEWEB)

1933-01-13

A process is described for the production of valuable hydrocarbons by treating distillable carbonaceous materials together with hydrogen gases, under pressure and in contact with catalysts, the process consisting in adding to the original materials, first or during treatment, organic sulfonic acids together with metals from the fourth or eighth groups of the periodic system or a combination of these, or organic carbosilicic acids or inorganic acids containing oxides of sulfur or nitrogen or the anhydrides of these inorganic acids or variation of these compounds.

Understanding the Organo-Carbonate Associations in Carbonaceous Chondrites with the Use of Micro-Raman Analysis

Science.gov (United States)

Chan, Q. H. S.; Zolensky, M. E.

2015-01-01

Carbonates can potentially provide sites for organic materials to accrue and develop into complex macromolecules. This study examines the organics associated with carbonates in carbonaceous chondrites using micron-Raman imaging.

Characterization of baking behaviour of carbonaceous materials by dilatation investigations

Energy Technology Data Exchange (ETDEWEB)

Born, M.; Seichter, A.; Starke, S.

1990-01-01

An increase in volume can be observed in carbonaceous materials during baking which is assumed to be the reason for strains and crack formation. It occurs most pronouncedly within a temperature range from 100 to 200{degree}C. The causes of such phenomena in products pressed at different temperatures are analyzed by means of a gas pressure model and a relaxation model. The factors influencing dilatation are subject to thermal analysis. 15 refs., 13 figs.

Uranium band types in carbonaceous sediments with different diagenesis levels

International Nuclear Information System (INIS)

Borstel, D. von.

1984-01-01

Uraniferous peats, lignites and coals were studied by chemical and geological methods in order to determine the influence of carbonaceous substances with different diagenesis levels on uranium enrichment in sediments. It was found that the main factor of deposit genesis is not the chemical bending of uranium to the organic substance but rather the reduction from mobile U(VI) to immobile U(IV) in the course of diagenesis to epigenesis. (orig./PW) [de

Managing ash from the combustion of solid waste

International Nuclear Information System (INIS)

Hauser, R.

1992-01-01

This paper reports that with millions of tons of refuse being combusted each year, increasing concern over the environment impact of the residue produced has caused both regulators and the resource recovery industry to address the technical and regulatory issues relating to the safe handling and disposal of ash. The basic issue concerning solid waste combustion ash management in this country is how, based on past, recent, and ongoing scientific research, solid waste combustion ash should be handled. Typically, refuse contains approximately 20 to 25 percent residue, which is collected either on grates at the bottom of the combustion chamber or filtered from the exhaust gases by the air pollution control equipment. The fly ash component of the total residue stream is between 10 and 30 percent of the total residue while the bottom ash content ranges from 70 to 90 percent of the total weight, depending upon the air pollution control equipment utilized, especially acid gas scrubbing equipment

Multivariate study of parameters in the determination of pesticide residues in apple by headspace solid phase microextraction coupled to gas chromatography-mass spectrometry using experimental factorial design.

Science.gov (United States)

Abdulra'uf, Lukman Bola; Tan, Guan Huat

2013-12-15

Solid-phase microextraction (SPME) is a solvent-less sample preparation method which combines sample preparation, isolation, concentration and enrichment into one step. In this study, multivariate strategy was used to determine the significance of the factors affecting the solid phase microextraction of pesticide residues (fenobucarb, diazinon, chlorothalonil and chlorpyrifos) using a randomised factorial design. The interactions and effects of temperature, time and salt addition on the efficiency of the extraction of the pesticide residues were evaluated using 2(3) factorial designs. The analytes were extracted with 100 μm PDMS fibres according to the factorial design matrix and desorbed into a gas chromatography-mass spectrometry detector. The developed method was applied for the analysis of apple samples and the limits of detection were between 0.01 and 0.2 μg kg(-)(1), which were lower than the MRLs for apples. The relative standard deviations (RSD) were between 0.1% and 13.37% with average recovery of 80-105%. The linearity ranges from 0.5-50 μg kg(-)(1) with correlation coefficient greater than 0.99. Copyright © 2013 Elsevier Ltd. All rights reserved.

Solid biomass barometer

International Nuclear Information System (INIS)

Anon.

2006-01-01

The European (EU 25) wish to substitute solid biomass origin energy consumption (principally wood and wood waste, but also straw, crop harvest residues, vegetal and animal waste) for a part of that of fossil fuel origin (petrol, gas and coal) is beginning to pay off. 58,7 million tons oil equivalent (Mtoe) of solid biomass was produced in 2005, i.e. a 3.1 Mtoe increase with respect to 2004. Production of primary energy coming from direct combustion of renewable municipal solid waste in incineration plants should also be added on to this figure. The 0,2 Mtoe increase in this production with respect to 2004 brings valorization of this type of waste up to 5,3 Mtoe in 2005. (author)

Distilling peat and other carbonaceous matters

Energy Technology Data Exchange (ETDEWEB)

Stones, W B

1850-03-07

Improvements in treating peat and other carbonaceous and ligneous matters, so as to obtain products therefrom are disclosed. These improvements consist, first, of a machine for compressing and partially drying peat. The unpressed peat is put into boxes and these into frames which are passed through between the bowls of a machine resembling a pair of squeezers. Secondly, consists in distilling, at a temperature of, say 700/sup 0/F, the compressed peat, with or without the addition of tar or fatty matter in retorts, and condensing the vapors in a series of vessels, arranged after the manner of Wolfe's bottles. The resulting charcoal may be extinguished by passing carbonic acid through it while in an air-tight box or chamber, and it may then be compressed into bricks, and used for locomotives and other purposes.

Aqueous electrochemical mechanisms in actinide residue processing. 1998 annual progress report

International Nuclear Information System (INIS)

Blanchard, D.L. Jr.; Burns, C.J.; Morris, D.E.; Smith, W.H.

1998-01-01

'New and/or improved solutions to the stabilization and volume reduction of nuclear materials processing residues are urgently needed. Mediated electrochemical oxidation/reduction (MEO/R) processes are one such approach for incinerator ash, combustibles, and other solid residues. However, questions remain concerning the mechanisms of these processes, and how they might be optimized. In addition, further research is merited to extend their range of applicability. Recent advances in the study of heterogeneous electron transfer in solid substrates have opened the door for the re-examination of electron transfer processes associated with redox mediated actinide dissolution. The authors develop a deeper understanding of the thermodynamic and mechanistic aspects of heterogeneous electron transfer that lie at the heart of these MEO/R processes. They will also develop and test new approaches based on the results of these fundamental studies using actual residue materials. Key aspects of this proposal include: (1) determination of the potential windows for oxidation/reduction of colloidal actinide oxides and actinide-bearing oxide and organic substrates and the e transfer kinetic parameters that govern the current--overpotential characteristics; (2) development of adaptations of mediation schemes and application of co-mediation reagents for oxidative and reductive dissolution based on complexation of the surface-bound or solid-phase actinides and/or the dissolved redox mediator;and (3) execution of bench-scale tests of new MEO/R schemes on actual residue materials.'

Fermentative utilization of glycerol residue for the production of acetic acid

Science.gov (United States)

Irvan; Trisakti, B.; Hasibuan, R.; Joli, M.

2018-02-01

Glycerol residue, frequently known as pitch, is a waste produced from the downstream product of crude glycerine distillation. With the increasing need of pure glycerine in the world, the glycerol residue produced is also increasing. Glycerol residue is a solid waste at room temperature, highly alkaline (pH > 13), corrosive, and categorized as hazardous and poisonous waste. In this research, acetic acid was produced from glycerol residue through the anaerobic fermentation process by using purple non-sulphur photosynthetic bacteria. The purpose of this study was to find out the influence of concentration change of glycerol residue on time and to find out the possibility of glycerol residue to be utilized as acetic acid. In this research, at first 400 g of glycerol residue was diluted with 200 ml of distilled water to change the glycerine phase, from solid to liquid at room temperature, acidified by using hydrochloric acid until pH 2. The top layer formed was fatty acid and triglycerides that should be removed. Meanwhile, the bottom layer was diluted glycerol residue which was then neutralized with caustic soda. To produce acetic acid, glycerol residue with various concentrations, salt, and purple non-sulphur photosynthetic bacteria were put together into a 100 ml bottle which had been previously sterilized, then incubated for four weeks under the light of 40-watt bulb. The result showed that on the 28th day of fermentation, the produced acetic acid were 0.28, 1.85, and 0.2% (w/w) by using glycerine with the concentration of 0.5, 1.0, and 1.5% (w/w), respectively.

Recent Development of Carbonaceous Materials for Lithium–Sulphur Batteries

Directory of Open Access Journals (Sweden)

Xingxing Gu

2016-11-01

Full Text Available The effects of climate change are just beginning to be felt, and as such, society must work towards strategies of reducing humanity’s impact on the environment. Due to the fact that energy production is one of the primary contributors to greenhouse gas emissions, it is obvious that more environmentally friendly sources of power are required. Technologies such as solar and wind power are constantly being improved through research; however, as these technologies are often sporadic in their power generation, efforts must be made to establish ways to store this sustainable energy when conditions for generation are not ideal. Battery storage is one possible supplement to these renewable energy technologies; however, as current Li-ion technology is reaching its theoretical capacity, new battery technology must be investigated. Lithium–sulphur (Li–S batteries are receiving much attention as a potential replacement for Li-ion batteries due to their superior capacity, and also their abundant and environmentally benign active materials. In the spirit of environmental harm minimization, efforts have been made to use sustainable carbonaceous materials for applications as carbon–sulphur (C–S composite cathodes, carbon interlayers, and carbon-modified separators. This work reports on the various applications of carbonaceous materials applied to Li–S batteries, and provides perspectives for the future development of Li–S batteries with the aim of preparing a high energy density, environmentally friendly, and sustainable sulphur-based cathode with long cycle life.

PROTO-PLANETARY DISK CHEMISTRY RECORDED BY D-RICH ORGANIC RADICALS IN CARBONACEOUS CHONDRITES

International Nuclear Information System (INIS)

Remusat, Laurent; Robert, Francois; Meibom, Anders; Mostefaoui, Smail; Delpoux, Olivier; Binet, Laurent; Gourier, Didier; Derenne, Sylvie

2009-01-01

Insoluble organic matter (IOM) in primitive carbonaceous meteorites has preserved its chemical composition and isotopic heterogeneity since the solar system formed ∼4.567 billion years ago. We have identified the carrier moieties of isotopically anomalous hydrogen in IOM isolated from the Orgueil carbonaceous chondrite. Data from high spatial resolution, quantitative isotopic NanoSIMS mapping of Orgueil IOM combined with data from electron paramagnetic resonance spectroscopy reveals that organic radicals hold all the deuterium excess (relative to the bulk IOM) in distinct, micrometer-sized, D-rich hotspots. Taken together with previous work, the results indicate that an isotopic exchange reaction took place between pre-existing organic compounds characterized by low D/H ratios and D-rich gaseous molecules, such as H 2 D + or HD 2 + . This exchange reaction most likely took place in the diffuse outer regions of the proto-planetary disk around the young Sun, offering a model that reconciles meteoritic and cometary isotopic compositions of organic molecules.

Proto-Planetary Disk Chemistry Recorded by D-Rich Organic Radicals in Carbonaceous Chondrites

Science.gov (United States)

Remusat, Laurent; Robert, François; Meibom, Anders; Mostefaoui, Smail; Delpoux, Olivier; Binet, Laurent; Gourier, Didier; Derenne, Sylvie

2009-06-01

Insoluble organic matter (IOM) in primitive carbonaceous meteorites has preserved its chemical composition and isotopic heterogeneity since the solar system formed ~4.567 billion years ago. We have identified the carrier moieties of isotopically anomalous hydrogen in IOM isolated from the Orgueil carbonaceous chondrite. Data from high spatial resolution, quantitative isotopic NanoSIMS mapping of Orgueil IOM combined with data from electron paramagnetic resonance spectroscopy reveals that organic radicals hold all the deuterium excess (relative to the bulk IOM) in distinct, micrometer-sized, D-rich hotspots. Taken together with previous work, the results indicate that an isotopic exchange reaction took place between pre-existing organic compounds characterized by low D/H ratios and D-rich gaseous molecules, such as H2D+ or HD2 +. This exchange reaction most likely took place in the diffuse outer regions of the proto-planetary disk around the young Sun, offering a model that reconciles meteoritic and cometary isotopic compositions of organic molecules.

Atmospheric pressure MALDI for the noninvasive characterization of carbonaceous ink from Renaissance documents.

Science.gov (United States)

Grasso, Giuseppe; Calcagno, Marzia; Rapisarda, Alessandro; D'Agata, Roberta; Spoto, Giuseppe

2017-06-01

The analytical methods that are usually applied to determine the compositions of inks from ancient manuscripts usually focus on inorganic components, as in the case of iron gall ink. In this work, we describe the use of atmospheric pressure/matrix-assisted laser desorption ionization-mass spectrometry (AP/MALDI-MS) as a spatially resolved analytical technique for the study of the organic carbonaceous components of inks used in handwritten parts of ancient books for the first time. Large polycyclic aromatic hydrocarbons (L-PAH) were identified in situ in the ink of XVII century handwritten documents. We prove that it is possible to apply MALDI-MS as a suitable microdestructive diagnostic tool for analyzing samples in air at atmospheric pressure, thus simplifying investigations of the organic components of artistic and archaeological objects. The interpretation of the experimental MS results was supported by independent Raman spectroscopic investigations. Graphical abstract Atmospheric pressure/MALDI mass spectrometry detects in situ polycyclic aromatic hydrocarbons in the carbonaceous ink of XVII century manuscripts.

Hazardous properties of paint residues from the furniture industry.

Science.gov (United States)

Vaajasaari, Kati; Kulovaara, Maaret; Joutti, Anneli; Schultz, Eija; Soljamo, Kari

2004-01-30

The objective of this study was to screen nine excess paint residues for environmental hazard and to evaluate their disposability in a non-hazardous or hazardous-waste landfill. These residues were produced in the process of spray-painting furniture. Residues were classified according to their leaching and ecotoxicological properties. Leaching properties were determined with the European standard SFS-EN 12457-2 leaching-test. The toxicity of the leaching-test eluates was measured with plant-, bacteria- and enzyme-inhibition bioassays. Total organic carbon, formaldehyde and solvent concentrations in the solid wastes and in the leaching-test eluates were analysed. It seemed likely that leached formaldehyde caused very high acute toxicity in leaching-test eluates of the dry-booth residues. This hypothesis was based on the fact that the formaldehyde concentrations in the leaching-test eluates of the dry-booth residues were 62-75 times higher than the EC50 value reported in the literature for formaldehyde. The results of the water-curtain booth residues showed that the samples with the highest TOC and aromatic solvent concentrations were also the most toxic. The studied excess paint residues were complex organic mixtures and contained large amounts of compounds not identifiable from chemical data. Therefore, the evaluation of the hazard based solely on available chemical data is unlikely to be sufficient, as evidenced by our study. Our results show that harmful compounds remain in the solid waste and the toxicity results of their leaching-test eluates show that toxicity may leach from residues in contact with water at landfill sites. They also confirm the benefit of combining chemical and ecotoxicological assays in assessing the potential environmental hazard of complex organic mixtures found in wastes. Copyright 2003 Elsevier B.V.

First Results of the “Carbonaceous Aerosol in Rome and Environs (CARE” Experiment: Beyond Current Standards for PM10

Directory of Open Access Journals (Sweden)

Francesca Costabile

2017-12-01

Full Text Available In February 2017 the “Carbonaceous Aerosol in Rome and Environs (CARE” experiment was carried out in downtown Rome to address the following specific questions: what is the color, size, composition, and toxicity of the carbonaceous aerosol in the Mediterranean urban background area of Rome? The motivation of this experiment is the lack of understanding of what aerosol types are responsible for the severe risks to human health posed by particulate matter (PM pollution, and how carbonaceous aerosols influence radiative balance. Physicochemical properties of the carbonaceous aerosol were characterised, and relevant toxicological variables assessed. The aerosol characterisation includes: (i measurements with high time resolution (min to 1–2 h at a fixed location of black carbon (eBC, elemental carbon (EC, organic carbon (OC, particle number size distribution (0.008–10 μ m, major non refractory PM1 components, elemental composition, wavelength-dependent optical properties, and atmospheric turbulence; (ii 24-h measurements of PM10 and PM2.5 mass concentration, water soluble OC and brown carbon (BrC, and levoglucosan; (iii mobile measurements of eBC and size distribution around the study area, with computational fluid dynamics modeling; (iv characterisation of road dust emissions and their EC and OC content. The toxicological assessment includes: (i preliminary evaluation of the potential impact of ultrafine particles on lung epithelia cells (cultured at the air liquid interface and directly exposed to particles; (ii assessment of the oxidative stress induced by carbonaceous aerosols; (iii assessment of particle size dependent number doses deposited in different regions of the human body; (iv PAHs biomonitoring (from the participants into the mobile measurements. The first experimental results of the CARE experiment are presented in this paper. The objective here is to provide baseline levels of carbonaceous aerosols for Rome, and to address

The leaching kinetics of cadmium from hazardous Cu-Cd zinc plant residues.

Science.gov (United States)

Li, Meng; Zheng, Shili; Liu, Biao; Du, Hao; Dreisinger, David Bruce; Tafaghodi, Leili; Zhang, Yi

2017-07-01

A large amount of Cu-Cd zinc plant residues (CZPR) are produced from the hydrometallurgical zinc plant operations. Since these residues contain substantial amount of heavy metals including Cd, Zn and Cu, therefore, they are considered as hazardous wastes. In order to realize decontamination treatment and efficient extraction of the valuable metals from the CZPR, a comprehensive recovery process using sulfuric acid as the leaching reagent and air as the oxidizing reagent has been proposed. The effect of temperature, sulfuric acid concentration, particle size, solid/liquid ratio and stirring speed on the cadmium extraction efficiency was investigated. The leaching kinetics of cadmium was also studied. It was concluded that the cadmium leaching process was controlled by the solid film diffusion process. Moreover, the order of the reaction rate constant versus H 2 SO 4 concentration, particle size, solid/liquid ratio and stirring speed was calculated. The XRD and SEM-EDS analysis results showed that the main phases of the secondary sulfuric acid leaching residues were lead sulfate and calcium sulfate. Copyright © 2017 Elsevier Ltd. All rights reserved.

Modules for estimating solid waste from fossil-fuel technologies

International Nuclear Information System (INIS)

Crowther, M.A.; Thode, H.C. Jr.; Morris, S.C.

1980-10-01

Solid waste has become a subject of increasing concern to energy industries for several reasons. Increasingly stringent air and water pollution regulations result in a larger fraction of residuals in the form of solid wastes. Control technologies, particularly flue gas desulfurization, can multiply the amount of waste. With the renewed emphasis on coal utilization and the likelihood of oil shale development, increased amounts of solid waste will be produced. In the past, solid waste residuals used for environmental assessment have tended only to include total quantities generated. To look at environmental impacts, however, data on the composition of the solid wastes are required. Computer modules for calculating the quantities and composition of solid waste from major fossil fuel technologies were therefore developed and are described in this report. Six modules have been produced covering physical coal cleaning, conventional coal combustion with flue gas desulfurization, atmospheric fluidized-bed combustion, coal gasification using the Lurgi process, coal liquefaction using the SRC-II process, and oil shale retorting. Total quantities of each solid waste stream are computed together with the major components and a number of trace elements and radionuclides

Organochemical characteristics of carbonaceous materials as indicators of heat recorded on an ancient plate-subduction fault

Science.gov (United States)

Kaneki, S.; Hirono, T.; Mukoyoshi, H.; Sampei, Y.; Ikehara, M.

2016-07-01

Coseismic shear stress and slip distance affect subduction-related earthquake processes. They need to be understood to evaluate the earthquake's mechanism and the tsunami generation potential near trenches. The amount of frictional heat generated depends on the shear stress and slip distance, which are therefore able to be derived from the temperature recorded in the fault. Here we developed a new temperature proxy for carbonaceous materials by performing spectroscopic, thermogravimetric, and organic elemental analyses in conjunction with heating experiments. We found marked anomalies in the infrared and Raman spectra and atomic compositions of carbonaceous materials retrieved from the slip zone of an ancient megasplay fault in the Cretaceous Shimanto accretionary complex, Japan: the infrared spectra show extinction of aliphatic C-H bonding and very weak aromatic C=C bonding, and the Raman spectra show a slightly elevated ratio of disordered band intensity to graphitic band intensity and relatively low H/C and O/C ratios. These correlate well with the spectral and elemental features of host-rock carbonaceous materials after heating to 600°C. Thus, we conclude that the slip zone experienced a temperature of 600°C during a past earthquake event, indicating coseismic slip of 2-9 m, which could have generated a large tsunami if the ruptures propagated to the seafloor.

Origin of fine carbonaceous particulate matter in the Western Mediterranean Basin: fossil versus modern sources

Science.gov (United States)

Cruz Minguillón, María.; Perron, Nolwenn; Querol, Xavier; Szidat, Sönke; Fahrni, Simon; Wacker, Lukas; Reche, Cristina; Cusack, Michael; Baltensperger, Urs; Prévôt, André S. H.

2010-05-01

The present work was carried out in the frame of the international field campaign DAURE (Determination of the sources of atmospheric Aerosols in Urban and Rural Environments in the western Mediterranean). The objective of this campaign is to study the aerosol pollution episodes occurring at regional scale during winter and summer in the Western Mediterranean Basin. As part of this campaign, this work focuses on identifying the origin of fine carbonaceous aerosols. To this end, fine particulate matter (PM1) samples were collected during two different seasons (February-March and July 2009) at two sites: an urban site (Barcelona, NE Spain) and a rural European Supersite for Atmospheric Aerosol Research (Montseny, NE Spain). Subsequently, 14C analyses were carried out on these samples, both in the elemental carbon (EC) fraction and the organic carbon (OC) fraction, in order to distinguish between modern carbonaceous sources (biogenic emissions and biomass burning emissions) and fossil carbonaceous sources (mainly road traffic). Preliminary results from the winter period show that 40% of the OC at Barcelona has a fossil origin whereas at Montseny this percentage is 30%. These values can be considered as unexpected given the nature of the sites. Nevertheless, the absolute concentrations of fossil OC at Barcelona and Montseny differ by a factor of 2 (the first being higher), since the total OC at Montseny is lower than at Barcelona. Further evaluation of results and comparison with other measurements carried out during the campaign are required to better evaluate the origin of the fine carbonaceous matter in the Western Mediterranean Basin. Acknowledgements: Spanish Ministry of Education and Science, for a Postdoctoral Grant awarded to M.C. Minguillón in the frame of Programa Nacional de Movilidad de Recursos Humanos del Plan nacional de I-D+I 2008-2011. Spanish Ministry of Education and Science, for the Acción Complementaria DAURE CGL2007-30502-E/CLI.

A unified momentum equation approach for computing thermal residual stresses during melting and solidification

Science.gov (United States)

Yeo, Haram; Ki, Hyungson

2018-03-01

In this article, we present a novel numerical method for computing thermal residual stresses from a viewpoint of fluid-structure interaction (FSI). In a thermal processing of a material, residual stresses are developed as the material undergoes melting and solidification, and liquid, solid, and a mixture of liquid and solid (or mushy state) coexist and interact with each other during the process. In order to accurately account for the stress development during phase changes, we derived a unified momentum equation from the momentum equations of incompressible fluids and elastoplastic solids. In this approach, the whole fluid-structure system is treated as a single continuum, and the interaction between fluid and solid phases across the mushy zone is naturally taken into account in a monolithic way. For thermal analysis, an enthalpy-based method was employed. As a numerical example, a two-dimensional laser heating problem was considered, where a carbon steel sheet was heated by a Gaussian laser beam. Momentum and energy equations were discretized on a uniform Cartesian grid in a finite volume framework, and temperature-dependent material properties were used. The austenite-martensite phase transformation of carbon steel was also considered. In this study, the effects of solid strains, fluid flow, mushy zone size, and laser heating time on residual stress formation were investigated.

Solid state radiolysis of non-proteinaceous amino acids in vacuum. Astrochemical implications

International Nuclear Information System (INIS)

Franco Cataldo; Giancarlo Angelini; Yaser Hafez; Susana Iglesias-Groth

2013-01-01

The analysis of the amino acids present in Murchison meteorite and in other carbonaceous chondrites has revealed the presence of 66 different amino acids. Only eight of these 66 amino acids are proteinaceous amino acids used by the present terrestrial biochemistry in protein synthesis, the other 58 amino acids are somewhat 'rare' or unusual or even 'unknown' for the current terrestrial biochemistry. For this reason in the present work a series of 'uncommon' non-proteinaceous amino acids, namely, l-2-aminobutyric acid, R(-)-2-aminobutyric acid, 2-aminoisobutyric acid (or α-aminoisobutyric acid), l-norleucine, l-norvaline, l-β-leucine, l-β-homoalanine, l-β-homoglutamic acid, S(-)-α-methylvaline and dl-3-aminoisobutyric acid were radiolyzed in vacuum at 3.2 MGy a dose equivalent to that emitted in 1.05 x 10 9 years from the radionuclide decay in the bulk of asteroids or comets. The residual amount of each amino acid under study remained after radiolysis was determined by differential scanning calorimetry in comparison to pristine samples. For optically active amino acids, the residual amount of each amino acid remained after radiolysis was also determined by optical rotatory dispersion spectroscopy and by polarimetry. With these analytical techniques it was possible to measure also the degree of radioracemization undergone by each amino acid after radiolysis. It was found that the non-proteinaceous amino acids in general do not show a higher radiation and radioracemization resistance in comparison to the common 20 proteinaceous amino acids studied previously. The unique exception is represented by ?-aminoisobutyric acid which shows an extraordinary resistance to radiolysis since 96.6 % is recovered unchanged after 3.2 MGy. Curiously α-aminoisobutyric acid is the most abundant amino acid found in carbonaceous chondrites. In Murchison meteorite α-aminoisobutyric acid represents more than 20 % of the total 66 amino acids found in this meteorite. (author)

Microfossils, biomolecules and biominerals in carbonaceous meteorites: implications to the origin of life

Science.gov (United States)

Hoover, Richard B.

2012-11-01

Environmental and Field Emission Scanning Electron Microscopy (ESEM and FESEM) investigations have shown that a wide variety of carbonaceous meteorites contain the remains of large filaments embedded within freshly fractured interior surfaces of the meteorite rock matrix. The filaments occur singly or in dense assemblages and mats and are often encased within carbon-rich, electron transparent sheaths. Electron Dispersive X-ray Spectroscopy (EDS) spot analysis and 2D X-Ray maps indicate the filaments rarely have detectable nitrogen levels and exhibit elemental compositions consistent with that interpretation that of the meteorite rock matrix. Many of the meteorite filaments are exceptionally well-preserved and show evidence of cells, cell-wall constrictions and specialized cells and processes for reproduction, nitrogen fixation, attachment and motility. Morphological and morphometric analyses permit many of the filaments to be associated with morphotypes of known genera and species of known filamentous trichomic prokaryotes (cyanobacteria and sulfur bacteria). The presence in carbonaceous meteorites of diagenetic breakdown products of chlorophyll (pristane and phytane) along with indigenous and extraterrestrial chiral protein amino acids, nucleobases and other life-critical biomolecules provides strong support to the hypothesis that these filaments represent the remains of cyanobacteria and other microorganisms that grew on the meteorite parent body. The absence of other life-critical biomolecules in the meteorites and the lack of detectable levels of nitrogen indicate the filaments died long ago and can not possibly represent modern microbial contaminants that entered the stones after they arrived on Earth. This paper presents new evidence for microfossils, biomolecules and biominerals in carbonaceous meteorites and considers the implications to some of the major hypotheses for the Origin of Life.

Nature and origin of the resistant carbonaceous polymorphs involved the fossilization of biogenic soil-aggregates

Science.gov (United States)

Courty, M.-A.

2012-04-01

The rare occurrence of organic-rich surface horizons in soil archives is widely accepted to resulting from their rapid degradation. We intend here to further elucidate how pedogenic signatures that initially formed at the soil surface could resist over long timescales to burial processes. We focus on the structural evolution of the biogenic soil aggregates that is controlled by the complex interaction of bioturbation, root colonization, microbial decomposition, chemical weathering and physical processes. The nature and origin of carbonaceous components that could possibly contribute to the long term preservation of biogenic soil-aggregates is particularly examined. The study is based on the comparison of pedogenic aggregated microfacies from present-day situations and the ones encountered in soil archives from contrasting edaphic conditions: Arctic Holocene soils from Spitsbergen, hyper-arid soils from the Moche valley (Peru), Holocene semi-arid Mediterranean soils from Northern Syria, late Pleistocene paleosols from lake Mungo (South Wales Australia) and late Pleistocene paleosols from the Ardeche valley (France). The assemblage and composition of biogenic soil-aggregated horizons has been characterized under the binocular microscope and in thin sections. The basic components have been separated by water sieving. A typology of carbonaceous polymorphs and associated composite materials has been established under the binocular. They have been characterized by SEM-EDS, Raman spectrometry, X-ray diffraction and TEM. The comparative study shows that all the biogenic soil-aggregates from the soil archives contain a high amount of similar exotic components that contrast from the parent materials by their fresh aspect and their hydrophobic properties. This exotic assemblage comprises various types of aliphatic carbonaceous polymorphs (filaments, agglutinates, spherules) and aromatic ones (vitrous char, graphite), carbon cenospheres, fine grained sandstones and rock clasts

Enhanced production of xylanase from locally isolated fungal strain using agro-industrial residues under solid-state fermentation.

Science.gov (United States)

Abdullah, Roheena; Nisar, Kinza; Aslam, Aafia; Iqtedar, Mehwish; Naz, Shagufta

2015-01-01

This study is related to the isolation of fungal strain for xylanase production using agro-industrial residues. Forty fungal strains with xylanolytic potential were isolated by using xylan agar plates and quantitatively screened in solid-state fermentation. Of all the tested isolates, the strain showing highest ability to produce xylanase was assigned the code Aspergillus niger LCBT-14. For the enhanced production of the enzyme, five different fermentation media were evaluated. Out of all media, M4 containing wheat bran gave maximum enzyme production. Effect of different variables including incubation time, temperature, pH, carbon and nitrogen sources has been investigated. The optimum enzyme production was obtained after 72 h at 30°C and pH 4. Glucose as a carbon source while ammonium sulphate and yeast extract as nitrogen sources gave maximum xylanase production (946 U/mL/min). This study was successful in producing xylanase by A. niger LCBT-14 economically by utilising cheap indigenous substrate.

Carbonaceous aerosols in Norwegian urban areas

Directory of Open Access Journals (Sweden)

K. E. Yttri

2009-03-01

Full Text Available Little is known regarding levels and source strength of carbonaceous aerosols in Scandinavia. In the present study, ambient aerosol (PM₁₀ and PM_2.5 concentrations of elemental carbon (EC, organic carbon (OC, water-insoluble organic carbon (WINSOC, and water-soluble organic carbon (WSOC are reported for a curbside site, an urban background site, and a suburban site in Norway in order to investigate their spatial and seasonal variations. Aerosol filter samples were collected using tandem filter sampling to correct for the positive sampling artefact introduced by volatile and semivolatile OC. Analyses were performed using the thermal optical transmission (TOT instrument from Sunset Lab Inc., which corrects for charring during analysis. Finally, we estimated the relative contribution of OC from wood burning based on the samples content of levoglucosan.

Levels of EC varied by more than one order of magnitude between sites, likely due to the higher impact of vehicular traffic at the curbside and the urban background sites. In winter, the level of particulate organic carbon (OC_p at the suburban site was equal to (for PM₁₀ or even higher (for PM_2.5 than the levels observed at the curbside and the urban background sites. This finding was attributed to the impact of residential wood burning at the suburban site in winter, which was confirmed by a high mean concentration of levoglucosan (407 ng m⁻³. This finding indicates that exposure to primary combustion derived OC_p could be equally high in residential areas as in a city center. It is demonstrated that OC_p from wood burning (OC_wood accounted for almost all OC_p at the suburban site in winter, allowing a new estimate of the ratio TC_p/levoglucosan for both PM₁₀ and PM_2.5. Particulate carbonaceous material (PCM

Genotoxicity and mutagenicity of solid waste leachates: A review

African Journals Online (AJOL)

user

2013-07-03

Jul 3, 2013 ... There is need for a shift from waste disposal to sustainable waste management. Awareness on possible health ... Key words: Solid waste leachate, genotoxicity, mutagenicity, environmental pollution. INTRODUCTION. Solid wastes .... landfills and incineration residues from Japan include persistent organic ...

Dissipation and residue of bifenthrin in wheat under field conditions.

Science.gov (United States)

You, Xiangwei; Jiang, Naiwen; Liu, Fengmao; Liu, Congyun; Wang, Suli

2013-02-01

Field trials were carried out to investigate the dissipation and residue levels of bifenthrin in wheat. After extraction with acetonitrile, the samples were cleaned up by dispersive solid-phase extraction and detected by gas chromatography-mass spectrometry. The half-lives of bifenthrin in wheat seedlings ranged from 2.4 to 10.5 days. At harvest time, the terminal residues of bifenthrin were below the maximum residue limit (0.5 mg/kg) set by Codex Alimentarius Committee or European Union in wheat grain, which suggested that the use of this pesticide was safe for humans. However, the relatively high residue levels of bifenthrin in wheat straw should be paid attention to.

Fabricating eco-friendly nanocomposites of SiC with morphologically-different nano-carbonaceous phases 

DEFF Research Database (Denmark)

Candelario, Victor M.; Moreno, Rodrigo; Guiberteau, Fernando

2018-01-01

A route based on aqueous colloidal processing followed by liquid-phase assisted spark-plasma-sintering (SPS) is described for fabricating eco-friendly nanocomposites of SiC with nano-carbonaceous phases (nanotubes, nanoplatelets, or nanoparticles). To this end, the conditions optimizing the aqueo...

Gasificación con aire en lecho fluidizado de los residuos sólidos del proceso industrial de la naranja//Air gasification in fluidized bed of solid residue the orange industrial process

Directory of Open Access Journals (Sweden)

Leonardo Aguiar-Trujillo

2012-12-01

Full Text Available La industria procesadora de la naranja genera elevados volúmenes de residuos sólidos. Este residuo se ha utilizado en la alimentación animal y en procesos bioquímicos; pero no se ha aprovechado a través de la gasificación. El objetivo del trabajo fue determinar el aporte energético por medio del proceso de gasificación, realizándose estudios de los residuos sólidos de naranja, utilizando aire en reactor de lecho fluidizado burbujeante (variando la temperatura de gasificación, relación estequiométrica y altura del lecho. En el proceso se utilizó un diseño de experimento factorial completo de 2k, valorando la influencia de las variables independientes y sus interacciones en las respuestas, con un grado de significación del 95 %. Se obtuvieron los parámetros para efectuar el proceso de gasificación de los residuos sólidos de naranja, obteniendo un gas de bajo poder calórico, próximo a 5046 kJ/m3N, demostrando sus cualidades para su aprovechamiento energético.Palabras claves: gasificación con aire, lecho fluidizado, residuo de naranja._______________________________________________________________________________AbstractThe orange industrial process generates high volumes of solid residue. This residue has been used as complement in the animal feeding and biochemical processes; but it has not taken advantage through of the gasification process. The objective of the work was to determine the energy contribution by means ofthe gasification process, were carried out studies of the orange solid residue, using air in reactor of bubbling fluidized bed (varying the gasification temperature, air ratio and bed height. In the process a design of complete factorial experiment of 2k, was used, valuing the influence of the independent variables and its interactions in the answers, using a confidence level of 95 %. Were obtained the parameters to make the process of gasification of the orange solid residue, obtaining a gas of lower heating

Factors influencing the outdoor concentration of carbonaceous aerosols at urban schools in Brisbane, Australia: Implications for children's exposure

International Nuclear Information System (INIS)

Crilley, L.R.; Ayoko, G.A.; Mazaheri, M.; Morawska, L.

2016-01-01

This comprehensive study aimed to determine the sources and driving factors of organic carbon (OC) and elemental carbon (EC) concentrations in ambient PM 2.5 in urban schools. Sampling was conducted outdoors at 25 schools in the Brisbane Metropolitan Area, Australia. Concentrations of primary and secondary OC were quantified using the EC tracer method, with secondary OC accounting for an average of 60%. Principal component analysis distinguished the contributing sources above the background and identified groups of schools with differing levels of primary and secondary carbonaceous aerosols. Overall, the results showed that vehicle emissions, local weather conditions and secondary organic aerosols (SOA) were the key factors influencing concentrations of carbonaceous component of PM 2.5 at these schools. These results provide insights into children's exposure to vehicle emissions and SOA at such urban schools. - Highlights: • We aimed to find the contributing sources to children's exposure at school. • Measured outdoor organic carbon and elemental carbon at 25 urban schools. • Schools varied in exposure to primary and secondary sources. • Secondary organic carbon the largest component of carbonaceous aerosols. • Vehicle emission levels at schools are primarily dependent on local traffic counts. - Key factors influencing concentrations of carbonaceous component of PM 2.5 at urban schools were found to be vehicle emissions, secondary organic aerosols and local weather conditions.

Regulations and decisions in environmental impact assessment of residues radioactivity content

International Nuclear Information System (INIS)

Santos, Adir Janete Godoy dos

2005-01-01

Surveillance of natural radionuclides in the environment did not have high priority over many years compared to that of man-made radioactivity. There is, however, an increasing interest in such measurements since enhanced exposure to natural radioactivity is receiving the same legal weight as any other radiation exposure. In this context the surveillance of technologically enhanced naturally occurring materials, called TENORM becomes important. In Brazil, the industries of processing and chemical compounds production were developed based on mining, milling, transformation and manufacture of ores from sedimentary origin, ignea or metamorphic, which must determine the radioactive composition of the generated solid wastes and residues. Many solids residues stored in the environment has been of environmental concern facing the industries and environmentalists in Brazil as it presents a potential threat to the surrounding environment and to individuals occupationally exposed. Radiation protection regulations have not been applied yet to these industries, as the Brazilian regulatory agency (Comissao Nacional de Energia Nuclear - CNEN) has only recently published a regulatory guide concerning mining and milling of naturally occurring radioactive materials, which may generate enhanced concentrations of radionuclides. With respect to external and internal exposure to natural radionuclides from the solid residues storage, the nuclides of 232 Th, 235 U and 238 U decay chains are relevant, due to the exposure of workers as well as of members of the public. Radionuclides released from a source can be present as ions, molecules, complexes, mononuclear or polynuclear species, colloids, pseudocolloids, particles or fragments varying in size (nominal molecular mass), structure, morphology, density, valence and charge properties. One of the main points in environmental impact assessment is to identify whether the chemical availability is under influence of these speciation

STUDY ON BIODEGRADATION TECHNOLOGY APPLICATION IN BULK IN THE REMEDIATION OF SOILS CONTAMINATED WITH POLYCYCLIC AROMATIC HYDROCARBONS

Directory of Open Access Journals (Sweden)

Irina Ramona PECINGINĂ

2015-05-01

Full Text Available Biodecontaminare methods are based on biodegradation in the subsurface presence of microorganisms capable of degrading most of carbonaceous organic pollutants and much of inorganic pollutants. Biodegradation in bulk meet that principle biological decontamination several ways. These methods are intended solely for solids, and is often used for on-site remediation of soils contaminated with organic products. Station bioremediation ensure reducing the harmfulness of residues from oil exploitation activities considered hazardous, using a bioremediation process. Bioremediation process will lead to reduction of oil content and thus reducing the hazard of waste.

Ethanol production from residual wood chips of cellulose industry: acid pretreatment investigation, hemicellulosic hydrolysate fermentation, and remaining solid fraction fermentation by SSF process.

Science.gov (United States)

Silva, Neumara Luci Conceição; Betancur, Gabriel Jaime Vargas; Vasquez, Mariana Peñuela; Gomes, Edelvio de Barros; Pereira, Nei

2011-04-01

Current research indicates the ethanol fuel production from lignocellulosic materials, such as residual wood chips from the cellulose industry, as new emerging technology. This work aimed at evaluating the ethanol production from hemicellulose of eucalyptus chips by diluted acid pretreatment and the subsequent fermentation of the generated hydrolysate by a flocculating strain of Pichia stipitis. The remaining solid fraction generated after pretreatment was subjected to enzymatic hydrolysis, which was carried out simultaneously with glucose fermentation [saccharification and fermentation (SSF) process] using a strain of Saccharomyces cerevisiae. The acid pretreatment was evaluated using a central composite design for sulfuric acid concentration (1.0-4.0 v/v) and solid to liquid ratio (1:2-1:4, grams to milliliter) as independent variables. A maximum xylose concentration of 50 g/L was obtained in the hemicellulosic hydrolysate. The fermentation of hemicellulosic hydrolysate and the SSF process were performed in bioreactors and the final ethanol concentrations of 15.3 g/L and 28.7 g/L were obtained, respectively.

Cadmium complexation by solid waste leachates

DEFF Research Database (Denmark)

Xu Ze Lun; Christensen, Thomas H.

1989-01-01

A previously reported method for determination of Cd species in solid waste leachates has been applied to ten leachate samples representing five different types of solid waste: refuse compost, flyash from coal combustion, sewage sludge, refuse incineration residues and landfilled municipal waste......, slowly labile complexes and stable complexes. Leachates originating from the same type of solid waste showed different fractions of Cd, in particular with respect to free divalent Cd and stable Cd complexes. Only coal flyash showed almost identical fractions of Cd in the two leachates. The latter is due...

Nonlinear elastic inclusions in isotropic solids

KAUST Repository

Yavari, A.

2013-10-16

We introduce a geometric framework to calculate the residual stress fields and deformations of nonlinear solids with inclusions and eigenstrains. Inclusions are regions in a body with different reference configurations from the body itself and can be described by distributed eigenstrains. Geometrically, the eigenstrains define a Riemannian 3-manifold in which the body is stress-free by construction. The problem of residual stress calculation is then reduced to finding a mapping from the Riemannian material manifold to the ambient Euclidean space. Using this construction, we find the residual stress fields of three model systems with spherical and cylindrical symmetries in both incompressible and compressible isotropic elastic solids. In particular, we consider a finite spherical ball with a spherical inclusion with uniform pure dilatational eigenstrain and we show that the stress in the inclusion is uniform and hydrostatic. We also show how singularities in the stress distribution emerge as a consequence of a mismatch between radial and circumferential eigenstrains at the centre of a sphere or the axis of a cylinder.

Elution behaviour of solid residues from thermal waste treatment and disposal

International Nuclear Information System (INIS)

Vetter, G.

1992-01-01

In the research part carried through so far, the leaching behaviour of residues of different waste combustion methods was compared with that of other materials frequently deposited at landfills as regards heavy metals and anions. Furthermore, specifically residues from different types of waste subjected to the Siemens semicoking process were investigated. The leaching behaviour of well vitrified slags approaches very much the favourable values of melting-chamber granulate from a black-coal-fired power plant. By contrast, poorly vitrified slags or slags from an ordinary waste combustion plant yield eluate concentrations exceeding in part the limiting values applicable to landfilling material. With vitrified slags, the type of waste burnt has no recognizable influence on leaching behaviour. (orig.) [de

Valuation of solid phase extraction disks in the determination of pesticide residues in surface and groundwater in Panama

International Nuclear Information System (INIS)

Jimenez, V.; Ramos de Jimenez, J.; Rojas, B.

1999-01-01

In Panama large quantities of pesticides are used in agriculture and livestock farming and there is increasing concern about their impact on public health and the environment. Chiriqui is the Province that registers the largest number of producers whose activities have impact on the environment, especially on surface and groundwater. Systematic monitoring programmes are non-existent due, in part, to the high cost of laboratory determination of environmental residues of pesticides. Within the framework of the FAO/IAEA/SIDA Coordinated Research Programme, efforts were focused on evaluating and optimising the use of solid phase extraction C 18 membrane disks in the analysis of surface and groundwater samples to determine pesticide residues. Factors studied were the effect of pre-washing and conditioning of the disks, flow rates, concentration level and matrix effects of field samples. Four pesticides, carbofuran, chlorothalonil, ametryn and chlorpyrifos were selected for these tests because preliminary analysis showed their presence in surface and groundwater. The technique significantly reduces the amount of organic solvents used as compared with the liquid-liquid extraction method. Quantifiable detection limits (Q L ) for the method were found to be 0.003 μg/L carbofuran, 0.016 μg/L chlorothalonil, 0.007 μg/L ametryn and 0.003 μg/L chlorpyrifos, when using standard spiked solutions. Recovery (%) was high when standard mixtures were used for the test runs but low when real surface water samples were tested, especially for chlorothalonil which was not recovered at all. (author)

A Case for Nebula Scale Mixing Between Non-Carbonaceous and Carbonaceous Chondrite Reservoirs: Testing the Grand Tack Model with Chromium Isotopic Composition of Almahata Sitta Stone 91A

Science.gov (United States)

Sanborn, M. E.; Yin, Q.-Z.; Goodrich, C. A.; Zolensky, M.; Fioretti, A. M.

2017-01-01

There is an increasing number of Cr-O-Ti isotope studies that show solar system materials are divided into two main populations, one carbonaceous chondrite (CC)-like and the other is non-carbonaceous (NC)-like, with minimal mixing attributed to a gap opened in the protoplanetary disk due to Jupiter's formation. The Grand Tack model suggests there should be large-scale mixing between S- and C-type asteroids, an idea supported by our recent work on chondrule (Delta)17O-e54Cr isotope systematics. The Almahata Sitta (AhS) meteorite provides a unique opportunity to test the Grand Tack model. The meteorite fell to Earth in October 2008 and has been linked to the asteroid 2008 TC3 which was discovered just prior to the fall of the AhS stones. The AhS meteorite is composed of up to 700 individual pieces with approx.140 of those pieces having some geochemical and/or petrologic studies. Almahata Sitta is an anomalous polymict ureilite with other meteorite components, including enstatite, ordinary, and carbonaceous chondrites with an approximate abundance of 70% ureilites and 30% chondrites. This observation has lead to the suggestion that TC3 2008 was a loosely aggregated rubble pile-like asteroid with the non-ureilite sample clasts within the rubble-pile. Due to the loosely-aggregated nature of AhS, the object disintegrated during atmospheric entry resulting in the weakly held clasts falling predominantly as individual stones in the AhS collection area. However, recent work has identified one sample of AhS, sample 91A, which may represent two different lithologies coexisting within a single stone. The predominate lithology type in 91A appears to be that of a C2 chondrite based on mineralogy but also contains olivine, pyroxene, and albite that have ureilite-like compositions. Previous Cr isotope investigations into AhS stones are sparse and what data is available show nearly uniform isotopic composition similar to that of typical ureilites with negative e54Cr values.

Anaerobic digestion of municipal solid waste: Technical developments

Energy Technology Data Exchange (ETDEWEB)

Rivard, C.J. [National Renewable Energy Lab., Golden, CO (United States)

1996-01-01

The anaerobic biogasification of organic wastes generates two useful products: a medium-Btu fuel gas and a compost-quality organic residue. Although commercial-scale digestion systems are used to treat municipal sewage wastes, the disposal of solid organic wastes, including municipal solid wastes (MSW), requires a more cost-efficient process. Modern biogasification systems employ high-rate, high-solids fermentation methods to improve process efficiency and reduce capital costs. The design criteria and development stages are discussed. These systems are also compared with conventional low-solids fermentation technology.

Conversion of lignocellulosic agave residues into liquid biofuels using an AFEX™-based biorefinery.

Science.gov (United States)

Flores-Gómez, Carlos A; Escamilla Silva, Eleazar M; Zhong, Cheng; Dale, Bruce E; da Costa Sousa, Leonardo; Balan, Venkatesh

2018-01-01

Agave-based alcoholic beverage companies generate thousands of tons of solid residues per year in Mexico. These agave residues might be used for biofuel production due to their abundance and favorable sustainability characteristics. In this work, agave leaf and bagasse residues from species Agave tequilana and Agave salmiana were subjected to pretreatment using the ammonia fiber expansion (AFEX) process. The pretreatment conditions were optimized using a response surface design methodology. We also identified commercial enzyme mixtures that maximize sugar yields for AFEX-pretreated agave bagasse and leaf matter, at ~ 6% glucan (w/w) loading enzymatic hydrolysis. Finally, the pretreated agave hydrolysates (at a total solids loading of ~ 20%) were used for ethanol fermentation using the glucose- and xylose-consuming strain Saccharomyces cerevisiae 424A (LNH-ST), to determine ethanol yields at industrially relevant conditions. Low-severity AFEX pretreatment conditions are required (100-120 °C) to enable efficient enzymatic deconstruction of the agave cell wall. These studies showed that AFEX-pretreated A. tequilana bagasse, A. tequilana leaf fiber, and A. salmiana bagasse gave ~ 85% sugar conversion during enzyme hydrolysis and over 90% metabolic yields of ethanol during fermentation without any washing step or nutrient supplementation. On the other hand, although lignocellulosic A. salmiana leaf gave high sugar conversions, the hydrolysate could not be fermented at high solids loadings, apparently due to the presence of natural inhibitory compounds. These results show that AFEX-pretreated agave residues can be effectively hydrolyzed at high solids loading using an optimized commercial enzyme cocktail (at 25 mg protein/g glucan) producing > 85% sugar conversions and over 40 g/L bioethanol titers. These results show that AFEX technology has considerable potential to convert lignocellulosic agave residues to bio-based fuels and chemicals in a biorefinery.

Direct determination of chromium in infant formulas employing high-resolution continuum source electrothermal atomic absorption spectrometry and solid sample analysis.

Science.gov (United States)

Silva, Arlene S; Brandao, Geovani C; Matos, Geraldo D; Ferreira, Sergio L C

2015-11-01

The present work proposed an analytical method for the direct determination of chromium in infant formulas employing the high-resolution continuum source electrothermal atomic absorption spectrometry combined with the solid sample analysis (SS-HR-CS ET AAS). Sample masses up to 2.0mg were directly weighted on a solid sampling platform and introduced into the graphite tube. In order to minimize the formation of carbonaceous residues and to improve the contact of the modifier solution with the solid sample, a volume of 10 µL of a solution containing 6% (v/v) H2O2, 20% (v/v) ethanol and 1% (v/v) HNO3 was added. The pyrolysis and atomization temperatures established were 1600 and 2400 °C, respectively, using magnesium as chemical modifier. The calibration technique was evaluated by comparing the slopes of calibration curves established using aqueous and solid standards. This test revealed that chromium can be determined employing the external calibration technique using aqueous standards. Under these conditions, the method developed allows the direct determination of chromium with limit of quantification of 11.5 ng g(-1), precision expressed as relative standard deviation (RSD) in the range of 4.0-17.9% (n=3) and a characteristic mass of 1.2 pg of chromium. The accuracy was confirmed by analysis of a certified reference material of tomato leaves furnished by National Institute of Standards and Technology. The method proposed was applied for the determination of chromium in five different infant formula samples. The chromium content found varied in the range of 33.9-58.1 ng g(-1) (n=3). These samples were also analyzed employing ICP-MS. A statistical test demonstrated that there is no significant difference between the results found by two methods. The chromium concentrations achieved are lower than the maximum limit permissible for chromium in foods by Brazilian Legislation. Copyright © 2015. Published by Elsevier B.V.

Photolytic process for gasification of carbonaceous material

International Nuclear Information System (INIS)

Zenty, S.

1979-01-01

Process and apparatus are disclosed for converting carbon dioxide to carbon monoxide by subjecting the carbon dioxide to radiation in the presence of carbonaceous material such as coal to form carbon monoxide. The preferred form of radiation is solar energy, and the process is preferably carried out in an atmosphere essentially free of oxygen. The invention also includes subjecting carbon monoxide to radiation to form purified carbon and useful heat energy. The two procedures can be combined into a single process for converting solar or other energy into useful thermal energy with the production of useful products. The reactor apparatus is specifically designed to carry out the radiation-induced conversions. Coal can be desulfurized and its caking characteristics altered by solar radiation in the presence of suitable gases. 3 figures

Dome C UltraCarbonaceous Antarctic MicroMeteorites Infrared and Raman fingerprints

OpenAIRE

Dartois, E.; Engrand, C.; Duprat, J.; Godard, M.; Charon, E.; Delauche, L.; Sandt, C.; Borondics, F.

2017-01-01

UltraCarbonaceous Antarctic MicroMeteorites (UCAMMs) represent a small fraction of interplanetary dust particles reaching the Earth's surface and contain large amounts of an organic component not found elsewhere. They are most probably sampling a contribution from the outer regions of the solar system to the local interplanetary dust particle flux. We characterize UCAMMs composition focusing on the organic matter, and compare the results to the insoluble organic matter (IOM) from primitive me...

The Insoluble Carbonaceous Material of CM Chondrites as Possible Source of Discrete Organics During the Asteroidal Aqueous Phase

Science.gov (United States)

Yabuta, H.; Williams, L.; Cody, G.; Pizzarello, S.

2005-01-01

The larger portion of the organic carbon in carbonaceous chondrites (CC) is present as a complex and heterogeneous macromolecular material that is insoluble in acids and most solvents (IOM). So far, it has been analyzed only as a whole by microscopy (TEM) and spectroscopy (IR, NMR, EPR), which have offered and overview of its chemical nature, bonding, and functional group composition. Chemical or pyrolytic decomposition has also been used in combination with GC-MS to identify individual compounds released by these processes. Their value in the recognition of the original IOM structure resides in the ability to properly interpret the decomposition pathways for any given process. We report here a preliminary study of IOM from the Murray meteorite that combines both the analytical approaches described above, under conditions that would realistically model the IOM hydrothermal exposure in the meteorite parent body. The aim is to document the possible release of water and solvent soluble organics, determine possible changes in NMR spectral features, and ascertain, by extension, the effect of this loss on the frame of the IOM residue. Additional information is included in the original extended abstract.

Chemical modelling of pore water composition from PFBC residues

International Nuclear Information System (INIS)

Karlsson, L.G.

1991-01-01

The concentration of trace elements varies depending on the source of the coal and also due to the combustion process used. Mercury is one important element among the trace elements in the coal residues, generally recognised as potentially harmful to the biological system. To predict the pore water concentrations of mercury and other important constituents leached from coal combustion residues disposal sites, mechanistic data on chemical reactions are required. The present study is an application of a basially thermodynamical approach using the geochemical code EQ3NR. The presence of discrete solid phases that control the aqueous concentrations of major elements such as aluminium, calcium and silicon are identified. Solid phases are modelled in equilibrium with a hypothetical pore water at a pH range of 7-11. In this study the thermodynamic database of EQ3NR has been complemented with data for cadmium, mercury and lead taken from the OECD/NEA Thermodynamic Database and from a compilation made by Lindsay. Possible solubility limiting phases for the important trace elements arsenic, cadmium, chromium, copper, mercury, nickel and lead have been identified. Concentrations of these trace elements as a function of pH in the hypothetical pore water were calculated using mechanistic thermodynamial data. The thermodynamical approach in this study seems justified because most solid residues that are either present or expected to form during weathering have relatively fast precipitation/dissolution kinetics. (21 refs., 18 figs., 5 tabs.)

Nonlinear elastic inclusions in isotropic solids

KAUST Repository

Yavari, A.; Goriely, A.

2013-01-01

We introduce a geometric framework to calculate the residual stress fields and deformations of nonlinear solids with inclusions and eigenstrains. Inclusions are regions in a body with different reference configurations from the body itself and can

Production of activated charcoal beads or green moldnings useful in stationary or fluidized bed uses rotary stirrer(s) for mixing carbonaceous powder with binder

DEFF Research Database (Denmark)

2000-01-01

In the production of activated charcoal beads or green moldings by mixing carbonaceous powder with a binder, mixing is carried out in a stirred vessel with rotary stirrer(s).......In the production of activated charcoal beads or green moldings by mixing carbonaceous powder with a binder, mixing is carried out in a stirred vessel with rotary stirrer(s)....

Sources of increase in lowermost stratospheric sulphurous and carbonaceous aerosol background concentrations during 1999–2008 derived from CARIBIC flights

Directory of Open Access Journals (Sweden)

Johan Friberg

2014-03-01

Full Text Available This study focuses on sulphurous and carbonaceous aerosol, the major constituents of particulate matter in the lowermost stratosphere (LMS, based on in situ measurements from 1999 to 2008. Aerosol particles in the size range of 0.08–2 µm were collected monthly during intercontinental flights with the CARIBIC passenger aircraft, presenting the first long-term study on carbonaceous aerosol in the LMS. Elemental concentrations were derived via subsequent laboratory-based ion beam analysis. The stoichiometry indicates that the sulphurous fraction is sulphate, while an O/C ratio of 0.2 indicates that the carbonaceous aerosol is organic. The concentration of the carbonaceous component corresponded on average to approximately 25% of that of the sulphurous, and could not be explained by forest fires or biomass burning, since the average mass ratio of Fe to K was 16 times higher than typical ratios in effluents from biomass burning. The data reveal increasing concentrations of particulate sulphur and carbon with a doubling of particulate sulphur from 1999 to 2008 in the northern hemisphere LMS. Periods of elevated concentrations of particulate sulphur in the LMS are linked to downward transport of aerosol from higher altitudes, using ozone as a tracer for stratospheric air. Tropical volcanic eruptions penetrating the tropical tropopause are identified as the likely cause of the particulate sulphur and carbon increase in the LMS, where entrainment of lower tropospheric air into volcanic jets and plumes could be the cause of the carbon increase.

Composition of municipal solid waste in Denmark

DEFF Research Database (Denmark)

Edjabou, Vincent Maklawe Essonanawe; Petersen, Claus; Scheutz, Charlotte

2014-01-01

Data for the composition of municipal solid waste is a critical basis for any assessment of waste technologies and waste management systems. The detailed quantification of waste fractions is absolutely needed for a better technological development of waste treatment. The current waste composition...... comparability to characterize municipal solid waste. This methodology was applied to residual waste collected from 1,442 households in three municipalities in Denmark. The main fractions contributing to the residual household waste were food waste and miscellaneous waste. Statistical analysis suggested...... of standardised and commonly accepted waste characterization methodologies, various approaches have been reported in literature. This limits both comparability and applicability of the results. The purpose of this study was to introduce a consistent methodology that reduces uncertainties and ensures data...

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

National Research Council Canada - National Science Library

Underwood, John

2000-01-01

...; overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid...

Changes in volatile profile of soybean residue (okara) upon solid-state fermentation by yeasts.

Science.gov (United States)

Vong, Weng Chan; Liu, Shao-Quan

2017-01-01

Soybean residue (okara), a by-product of soymilk, is produced in large volumes by the soy food industry and is often discarded due to its undesirable flavour. As it contains a considerable amount of protein and fats, biotransformation of okara to improve its flavour presents an opportunity for alternative utilisation. This paper evaluated 10 yeasts in the solid-state fermentation of okara based on their volatile profiles as analysed with HS-SPME GC-MS/FID. Four 'dairy yeasts' (Geotrichum candidum, Yarrowia lipolytica, Debaryomyces hansenii and Kluyveromyces lactis) and six 'wine yeasts' (Saccharomyces cerevisiae, Lachancea thermotolerans, Metschnikowia pulcherrima, Pichia kluyveri, Torulaspora delbrueckii, and Williopsis saturnus) were studied. The main off-odourants in okara, hexanal and trans-2-hexenal, significantly decreased after fermentation due to their bioconversion into methyl ketones and/or esters. The okara fermented by dairy yeasts contained greater proportions of methyl ketones, while that by wine yeasts contained more ethyl and acetyl esters. Notably, the okara fermented by W. saturnus contained 13 esters and the total GC-FID peak area of esters was about 380 times that in fresh okara, leading to a perceptible fruity note. Okara can be exploited as an inexpensive substrate for bioflavour extraction and/or a more pleasant food ingredient via yeast fermentation. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Acid transformation of bauxite residue: Conversion of its alkaline characteristics.

Science.gov (United States)

Kong, Xiangfeng; Li, Meng; Xue, Shengguo; Hartley, William; Chen, Chengrong; Wu, Chuan; Li, Xiaofei; Li, Yiwei

2017-02-15

Bauxite residue (BR) is a highly alkaline solid hazardous waste produced from bauxite processing for alumina production. Alkaline transformation appears to reduce the environmental risk of bauxite residue disposal areas (BRDAs) whilst potentially providing opportunities for the sustainable reuse and on-going management of BR. Mineral acids, a novel citric acid and a hybrid combination of acid-gypsum treatments were investigated for their potential to reduce residue pH and total alkalinity and transform the alkaline mineral phase. XRD results revealed that with the exception of andradite, the primary alkaline solid phases of cancrinite, grossular and calcite were transformed into discriminative products based on the transformation used. Supernatants separated from BR and transformed bauxite residue (TBR) displayed distinct changes in soluble Na, Ca and Al, and a reduction in pH and total alkalinity. SEM images suggest that mineral acid transformations promote macro-aggregate formation, and the positive promotion of citric acid, confirming the removal or reduction in soluble and exchangeable Na. NEXAFS analysis of Na K-edge revealed that the chemical speciation of Na in TBRs was consistent with BR. Three acid treatments and gypsum combination had no effect on Na speciation, which affects the distribution of Na revealed by sodium STXM imaging. Copyright © 2016 Elsevier B.V. All rights reserved.

Extraterrestrial Amino Acids Identified in Metal-Rich CH and CB Carbonaceous Chondrites from Antarctica

Science.gov (United States)

Burton, Aaron S.; Elsila, Jamie E.; Hein, Jason E.; Glavin, Daniel P.; Dworkin, Jason P.

2013-01-01

Carbonaceous chondrites contain numerous indigenous organic compounds and could have been an important source of prebiotic compounds required for the origin of life on Earth or elsewhere. Extraterrestrial amino acids have been reported in five of the eight groups of carbonaceous chondrites and are most abundant in CI, CM, and CR chondritesbut are also present in the more thermally altered CV and CO chondrites. We report the abundance, distribution, and enantiomeric and isotopic compositions of simple primary amino acids in six metal-rich CH and CB carbonaceous chondrites that have not previously been investigated for amino acids: Allan Hills (ALH) 85085 (CH3), Pecora Escarpment(PCA) 91467 (CH3), Patuxent Range (PAT) 91546 (CH3), MacAlpine Hills (MAC) 02675(CBb), Miller Range (MIL) 05082 (CB), and Miller Range (MIL) 07411 (CB). Amino acid abundances and carbon isotopic values were obtained by using both liquid chromatography time-of-flight mass spectrometry and fluorescence, and gas chromatography isotope ratiomass spectrometry. The (delta D, delta C-13, delta N-15) ratios of multiple amino acids fall outside of the terrestrial range and support their extraterrestrial origin. Extracts of CH chondrites were found to be particularly rich in amino acids (1316 parts per million, ppm) while CB chondrite extracts had much lower abundances (0.22 ppm). The amino acid distributions of the CH and CB chondrites were distinct from the distributions observed in type 2 and 3 CM and CR chondrites and contained elevated levels of beta-, gamma-, and delta-amino acids compared to the corresponding alpha-amino acids, providing evidence that multiple amino acid formation mechanisms were important in CH and CB chondrites.

Laboratory Studies Of Circumstellar Carbonaceous Grain Formation

Science.gov (United States)

Contreras, Cesar; Sciamma-O'Brien, Ella; Salama, Farid

2014-06-01

The study of the formation processes of dust is essential to understand the budget of extraterrestrial organic molecules. Although dust with all its components plays an important role in the evolution of interstellar (IS) chemistry and in the formation of organic molecules, little is known on the formation processes of carbonaceous dust. We report the progress that was recently achieved in this domain using NASA Ames’ COSmIC facility (Contreras & Salama 2013, ApJS, 208, 6). PAHs are important chemical building blocks of IS dust. They are detected in IDPs and in meteoritic samples. Additionally, observational, laboratory, and theoretical studies have shown that PAHs are an important, ubiquitous component of the ISM. The formation of PAHs from smaller molecules has not been extensively studied. Therefore, we have performed laboratory experiments to study the dynamic processes of carbon grain formation, starting from the smallest hydrocarbon molecules into the formation of larger PAH and further into nanograins. Studies of IS dust analogs formed from a variety of PAH and hydrocarbon precursors as well as species that include the atoms O, N, and S, have recently been performed in our laboratory using the COSmIC facility to provide conditions that simulate IS and circumstellar environments. The species formed in the COSmiC chamber through a pulsed discharge nozzle plasma source are detected and characterized with a cavity ringdown spectrometer coupled to a time-of-flight mass spectrometer, thus providing both spectroscopic and ion mass information in-situ. Analysis of solid soot particles was also conducted using scanning electron microscopy at the UCSC/NASA Ames’ MACS facility. The SEM analysis of the deposition of soot from methane and acetylene precursors seeded in argon plasmas provide examples on the types of nanoparticles and micrograins that are produced in these gas mixtures under our experimental conditions. From these measurements, we derive information on

Amino Acid Chemistry as a Link Between Small Solar System Bodies and Carbonaceous Chondrites

Science.gov (United States)

Glavin, Daniel P.; Ehrenfreund, Pascale; Botta, Oliver; Cooper, George; Bada, Jeffrey L.

2000-01-01

Establishing chemical links between meteorites and small solar system bodies, such as comets and asteroids, provides a tool for investigating the processes that occurred during the formation of the solar system. Carbonaceous meteorites are of particular interest, since they may have seeded the early Earth with a variety of prebiotic organic compounds including amino acids, purines and pyrimidines, which are thought to be necessary for the origin of life. Here we report the results of high-performance liquid chromatography (HPLC) based amino acid analyses of the acid-hydrolyzed hot water extracts from pristine interior pieces of the CI carbonaceous chondrites Orgueil and Ivuna and the CM meteorites Murchison and Murray. We found that the CI meteorites Orgueil and Ivuna contained high abundances of beta-alanine and glycine, while only traces of other amino acids like alanine, alpha-amino-n-butryic acid (ABA) and alpha-aminoisobutyric acid (AIB) were detected in these meteorites. Carbon isotopic measurements of beta-alanine and glycine in Orgueil by gas chromatography combustion-isotope ratio mass spectrometry clearly indicate an extraterrestrial origin of these amino acids. The amino acid composition of Orgueil and Ivuna was strikingly different from the CM chondrites Murchison and Murray. The most notable difference was the high relative abundance of B-alanine in Orgueil and Ivuna compared to Murchison and Murray. Furthermore, AIB, which is one of the most abundant amino acids found in Murchison and Murray, was present in only trace amounts in Orgueil and Ivuna. Our amino acid data strongly suggest that the CI meteorites Orgueil and Ivuna came from a different type of parent body than the CM meteorites Murchison and Murray, possibly from an extinct comet. It is generally thought that carbonaceous meteorites are fragments of larger asteroidal bodies delivered via near Earth objects (NEO). Orbital and dynamic studies suggest that both fragments of main belt asteroids

Energy conservation and production from solid residues - alternative for two problems: wastes and energy; Conservacao e producao de energia a partir de residuos solidos - alternativa para dois problemas: lixo e energia

Energy Technology Data Exchange (ETDEWEB)

Reno, Francisco de Assis Grillo [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica. Planejamento de Sistemas Energeticos]. E-mail: fgrillo@fem.unicamp.br; Streb, Cleci Schalemberger [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica; Piunti, Regina Celia [Universidade Estadual de Campinas, SP (Brazil)]. E-mail: repiunti@ig.com.br

2002-07-01

This paper explores possibilities of energy conservation and production through the using domestic solid residues, aiming the disposal impacts and improvement the energy supplying as well. For energy conservation,the recycling, reduction and re utilization will be mentioned. For the energy recovering the burning of organic material in sanitary landfill and incineration of plastics and tires.

Residue management at Rocky Flats

International Nuclear Information System (INIS)

Olencz, J.

1995-01-01

Past plutonium production and manufacturing operations conducted at the Rocky Flats Environmental Technology Site (RFETS) produced a variety of plutonium-contaminated by-product materials. Residues are a category of these materials and were categorized as open-quotes materials in-processclose quotes to be recovered due to their inherent plutonium concentrations. In 1989 all RFETS plutonium production and manufacturing operations were curtailed. This report describes the management of plutonium bearing liquid and solid wastes

Leaching Behavior of Circulating Fluidised Bed MSWI Air Pollution Control Residue in Washing Process

Directory of Open Access Journals (Sweden)

Zhiliang Chen

2016-09-01

Full Text Available In this study, air pollution control (APC residue is conducted with water washing process to reduce its chloride content. A novel electrical conductivily (EC measurement method is proposed to monitor the dynamic change of chloride concentrations in leachate as well as the chloride content of the residue. The method equally applies to various washing processes with different washing time, liquid/solid ratio and washing frequency. The results show that washing effectively extracts chloride salts from APC residues, including those from circulating fluidized bed (CFB municipal solid waste incineration (MSWI. The most appropriate liquid/solid ratio and washing time in the first washing are found to be around 4 L water per kg of APC residue and 30 min, respectively, and washing twice is required to obtain maximum dissolution. The pH value is the major controlling factor of the heavy metals speciation in leachate, while chloride concentration also affects the speciation of Cd. Water washing causes no perceptible transfer of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs from the APC residue to leachate. The chloride concentration is strongly related with electrical conductivity (EC, as well as with the concentrations of calcium, sodium and potassium of washing water. Their regression analyses specify that soluble chloride salts and EC could act as an indirect indicator to monitor the change of chloride concentration and remaining chloride content, thus, contributing to the selection of the optimal washing conditions.

Effect of drying on leaching testing of treated municipal solid waste incineration APC-residues

DEFF Research Database (Denmark)

Hu, Y.; Hyks, Jiri; Astrup, Thomas

2008-01-01

Air-pollution-control (APC) residues from waste incinerators are hazardous waste according to European legislation and must be treated prior to landfilling. Batch and column leaching data determine which type of landfill can receive the treated APC-residues. CEN standards are prescribed...

The nev diffractometer ARES for the analysis of residual stresses

Czech Academy of Sciences Publication Activity Database

Staron, P.; Ruhnau, H. U.; Marmotti, M.; Mikula, Pavol; Kampmann, R.

276/278, - (2000), s. 158-159 ISSN 0921-4526 Institutional research plan: CEZ:AV0Z1048901 Keywords : neutron instruments * residual stress Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.893, year: 2000

Determination of six polyether antibiotic residues in foods of animal origin by solid phase extraction combined with liquid chromatography-tandem mass spectrometry.

Science.gov (United States)

Ha, Jing; Song, Ge; Ai, Lian-Feng; Li, Jian-Chen

2016-04-01

A new method using solid phase extraction (SPE) combined with liquid chromatography-tandem mass spectrometry (LC-MS/MS) has been developed for the determination of six polyether antibiotics, including lasalocid, salinomycin, monensin, narasin, madubamycin and nigericin residues, in foods of animal origin. The samples were extracted with acetonitrile and purified by ENVI-Carb SPE columns after comparing the impurity effect and maneuverability of several SPE cartridges. Subsequently, the analytes were separated on a Hypersil Gold column (2.1×150mm, 5μm) and analyzed by MS/MS detection. The limit of quantization (LOQ) for milk and chicken was 0.4μg/kg, and for chicken livers and eggs, it was 1μg/kg. The linearity was satisfactory with a correlation coefficient of >0.9995 at concentrations ranging from 2 to 100μg/L. The average recoveries of the analytes fortified at three levels ranged from 68.2 to 114.3%, and the relative standard deviations ranged from 4.5 to 12.1%. The method was suitable for quantitative analysis and confirmation of polyether antibiotic residues in foods of animal origin. Copyright © 2016 Elsevier B.V. All rights reserved.

A European Aerosol Phenomenology -4: Harmonized Concentrations of Carbonaceous Aerosol at 10 Regional Background Sites Across Europe.

Czech Academy of Sciences Publication Activity Database

Cavalli, F.; Areskoug, H.; Ceburnis, D.; Čech, J.; Genberg, J.; Harrison, R. M.; Jaffrezo, J.L.; Kiss, G.; Laj, P.; Mihalopoulos, N.; Perez, N.; Quincey, P.; Schwarz, Jaroslav; Sellegri, K.; Spindler, G.; Swietlicki, E.; Theodosi, C.; Yttri, K.E.; Aas, W.; Putaud, J.P.

2016-01-01

Roč. 144, NOV 2016 (2016), s. 133-145 ISSN 1352-2310 Institutional support: RVO:67985858 Keywords : aerosol * carbonaceous * PM Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.629, year: 2016

R Raman Spectroscopy and Petrology of Antarctic CR Chondrites: Comparison with Other Carbonaceous Chondrites

Science.gov (United States)

Komatsu, M.; Fagan, T. J.; Yamaguchi, A.; Mikouchi, T.; Zolensky, M. E.; Yasutake, M.

2015-01-01

In Renazzo-like carbonaceous (CR) chondrites, abundant original Fe,Ni-metal is preserved in chrondules, but the matrix is characterized by fine-grained magnetite with phyllosilicate. This combination of reduced Fe in chrodrules with oxidized Fe and phyllosilicate in the matrix has been attributed to aqueous alteration of matrix at relatively low temperatures.

Radiation effects on methane in the presence of molecular sieves

International Nuclear Information System (INIS)

Shimizu, Y.; Nagai, S.; Hatada, M.

1983-01-01

Product analysis has been carried out for the radiation-induced reaction of methane in the presence of molecular sieves (MS) 3A, 4A, 5A and 13X. Irradiation of methane over MS 4A selectively produces C 2 hydrocarbons, while the use of MS 5A leads to C 2 and C 3 hydrocarbons. The selectivity and yields of these hydrocarbons, however, decrease with irradiation time, owing to deposition of carbonaceous solid produced from methane on the surface of the molecular sieves. The carbonaceous solid is decomposed to low-molecular-weight hydrocarbons when irradiated in an H 2 atmosphere. Material balance estimated for the radiation-chemical reaction of argon containing 2 mol% methane over MS 5A reveals that the carbonaceous solid is highly abundant in carbon atoms. On the other hand the formation of carbonaceous solids plays a less important role in the radiation-chemical reaction of methane in the presence of silica gel, which is found to exhibit greater activity for the formation of hydrocarbons than the molecular sieves. (author)

Laboratory test investigations on soil water characteristic curve and air permeability of municipal solid waste.

Science.gov (United States)

Shi, Jianyong; Wu, Xun; Ai, Yingbo; Zhang, Zhen

2018-05-01

The air permeability coefficient has a high correlation with the water content of municipal solid waste. In this study, continuous drying methodology using a tension meter was employed to construct the soil water characteristic curve of municipal solid waste (M-SWCC). The municipal solid waste air permeability test was conducted by a newly designed apparatus. The measured M-SWCC was well reproduced by the van Genuchten (V-G) model and was used to predict the parameters of typical points in M-SWCC, including saturated water content, field capacity, residual water content and water content at the inflection point. It was found that the M-SWCC was significantly influenced by void ratio. The final evaporation and test period of M-SWCC increase with the increase in void ratio of municipal solid waste. The evolution of air permeability coefficient with water content of municipal solid waste depicted three distinct characteristic stages. It was observed that the water contents that corresponded to the two cut-off points of the three stages were residual water content and water content at the inflection point, respectively. The air permeability coefficient of municipal solid waste decreased with the increase of the water content from zero to the residual water content. The air permeability coefficient was almost invariable when the water content increased from residual water content to the water content at the inflection point. When the water content of municipal solid waste exceeded the water content at the inflection point, the air permeability coefficient sharply decreased with the increase of water content.

Matrix mineralogy of the Lance CO3 carbonaceous chondrite: A transmission electron microscope study

International Nuclear Information System (INIS)

Keller, L.P.; Buseck, P.R.

1990-01-01

The Lance CO3 carbonaceous chondrite (CC) is less altered than the CI and CM chondrites and so provides a view of the mineralogy and textures resulting from the earliest stages of aqueous alteration of CCs. Matrix olivine in Lance has been partly altered to fine-grained, Fe-bearing serpentine and poorly crystalline Fe 3+ oxide, a process that required both hydration and oxidation. Serpentine occurs as discrete packets separated from the olivine surfaces by the Fe 3+ oxide. The Fe released during the dissolution of olivine was partly incorporated into the serpentine; the remainder was oxidized to form Fe 3+ oxide. Matrix metal was also altered to produce Fe oxides, leaving the residual metal enriched in Ni. Olivine grains in Lance matrix contain channels along their [100] and [001] directions. The formation and convergence of such channels resulted in a grain-size reduction of the olivine. The alteration was pervasive but incomplete, suggesting a limited availability of fluid. A brief study of two other CO chondrites, Kainsaz and Warrenton, shows that these meteorites do not contain phyllosilicates in their matrices, although both contain Fe 3+ oxide between olivine grains. Prior to its alteration, Lance probably resembled Kainsaz, an unaltered CO3 chondrite. The alteration assemblage in Lance is only slightly different from that in Mokoia and essentially the same as that in C3 xenoliths from Murchison. Alteration products in Lance show greater similarities to CI than to CM chondrites

Impact of carbonaceous materials in soil on the transport of soil-bound PAHs during rainfall-runoff events

International Nuclear Information System (INIS)

Luo, Xiaolin; Zheng, Yi; Wu, Bin; Lin, Zhongrong; Han, Feng; Zhang, Wei; Wang, Xuejun

2013-01-01

Polycyclic Aromatic Hydrocarbons (PAHs) transported from contaminated soils by surface runoff pose significant risk for aquatic ecosystems. Based on a rainfall-runoff simulation experiment, this study investigated the impact of carbonaceous materials (CMs) in soil, identified by organic petrology analysis, on the transport of soil-bound PAHs under rainfall conditions. The hypothesis that composition of soil organic matter significantly impacts the enrichment and transport of PAHs was proved. CMs in soil, varying significantly in content, mobility and adsorption capacity, act differently on the transport of PAHs. Anthropogenic CMs like black carbon (BC) largely control the transport, as PAHs may be preferentially attached to them. Eventually, this study led to a rethink of the traditional enrichment theory. An important implication is that CMs in soil have to be explicitly considered to appropriately model the nonpoint source pollution of PAHs (possibly other hydrophobic chemicals as well) and assess its environmental risk. -- Highlights: •Composition of SOM significantly impacts the enrichment and transport of PAHs. •Anthropogenic carbonaceous materials in soil largely control the transport of PAHs. •The classic enrichment theory is invalid if anthropogenic CMs are abundant in the soil. •Organic petrology analysis introduced to study the fate and transport of PAHs. -- Anthropogenic carbonaceous materials in soil, especially black carbon, largely control the transport of soil-bound PAHs during rainfall-runoff events

Potential of ensiling for efficient management of spent residue from solid state fermentation system

OpenAIRE

Roussos, Sevastianos; Raimbault, Maurice; Geoffroy, F.; Saucedo-Castaneda, G.; Lonsane, B.K.

1992-01-01

Studies on ensiling of spent solids from solid state fermentation process for production of cellulases by #Trichoderma harzianum$ showed that good quality ensiled solids can be obtained by using about 43% initial substrate dry matter with 0.3% ensiling additive. (Résumé d'auteur)

Implementing a new EPR lineshape parameter for organic radicals in carbonaceous matter.

Science.gov (United States)

Bourbin, Mathilde; Du, Yann Le; Binet, Laurent; Gourier, Didier

2013-07-17

Electron Paramagnetic Resonance (EPR) is a non-destructive, non-invasive technique useful for the characterization of organic moieties in primitive carbonaceous matter related to the origin of life. The classical EPR parameters are the peak-to-peak amplitude, the linewidth and the g factor; however, such parameters turn out not to suffice to fully determine a single EPR line. In this paper, we give the definition and practical implementation of a new EPR parameter based on the signal shape that we call the R10 factor. This parameter was originally defined in the case of a single symmetric EPR line and used as a new datation method for organic matter in the field of exobiology. Combined to classical EPR parameters, the proposed shape parameter provides a full description of an EPR spectrum and opens the way to novel applications like datation. Such a parameter is a powerful tool for future EPR studies, not only of carbonaceous matter, but also of any substance which spectrum exhibits a single symmetric line. The paper is a literate program-written using Noweb within the Org-mode as provided by the Emacs editor- and it also describes the full data analysis pipeline that computes the R10 on a real EPR spectrum.

Solar radiation synthesis of functional carbonaceous materials using Al2O3/TiO2-Cu-HA doped catalyst

Science.gov (United States)

Stanciu, Elena Manuela; Pascu, Alexandru; Roată, Ionut Claudiu; Croitoru, Cătălin; Tierean, Mircea; Rosca, Julia Mirza; Hulka, Iosif

2018-04-01

Single carbon nanotubes were synthesized through a physical vapor deposition method, using concentrated solar radiation as means of vaporization and promoting the formation of carbonaceous plasma plume. A novel catalyst, containing multiple hybrid ceramic/metal phases has been obtained through flame spraying. In conjunction with this catalyst, good quality nanomaterials, such as long single-walled nanotubes and nanoparticles have been obtained and characterized by both morphological (SEM, TEM) as well as structural means on analysis (XRD, FTIR). A mild oxidation of the carbonaceous phase has been reported, which could prove useful in applications in conjunction with metals or hydrophilic polymers as potential matrices for nanocomposites obtaining.

Power generation from solid fuels

CERN Document Server

Spliethoff, Hartmut

2010-01-01

Power Generation from Solid Fuels introduces the different technologies to produce heat and power from solid fossil (hard coal, brown coal) and renewable (biomass, waste) fuels, such as combustion and gasification, steam power plants and combined cycles etc. The book discusses technologies with regard to their efficiency, emissions, operational behavior, residues and costs. Besides proven state of the art processes, the focus is on the potential of new technologies currently under development or demonstration. The main motivation of the book is to explain the technical possibilities for reduci

Agglomeration Determines Effects of Carbonaceous Nanomaterials on Soybean Nodulation, Dinitrogen Fixation Potential, and Growth in Soil

Science.gov (United States)

The potential effects of carbonaceous nanomaterials (CNMs) on agricultural plants are of concern. However, little research has been performed using plants cultivated to maturity in soils contaminated with various CNMs at different concentrations. Here, we grew soybean for 39 days...

In situ observation of D-rich carbonaceous globules embedded in NWA 801 CR2 chondrite

Science.gov (United States)

Hashiguchi, Minako; Kobayashi, Sachio; Yurimoto, Hisayoshi

2013-12-01

Eighty-five D-rich carbonaceous particles were identified in the matrix of the NWA 801 CR2 chondrite using isotope microscopy. The occurrence of 67 D-rich carbonaceous particles was characterized using secondary electron microscopy combined with X-ray elemental mapping. The close association of H and C, and D-enrichment suggests that the D-rich carbonaceous particles correspond to organic matter. The D-rich organic particles were scattered ubiquitously throughout the matrix at a concentration of approximately 660 ppm. The morphology of the D-rich carbonaceous particles is globular up to about 1 μm in diameter and is classified into four types: ring globules, round globules, irregular-shaped globules, and globule aggregates. The ring globules are ring-shaped organic matter containing silicate and/or oxide, with or without a void in the center. This is the first report of silicate and oxide grains surrounded by D-rich organic matter. The globule aggregates are composed of several D-rich organic globules mixed with silicates. Morphology of ring globules is very similar to core-mantle grain produced in the molecular cloud or in the outer solar nebula inferring by astronomy, suggesting that the organic globules have formed by UV photolysis in the ice mantle. Silicates or oxides attached to D-rich organic globules are the first observation among chondrites so far and may be unique nature of CR2 chondrites. The hydrogen isotopic compositions of the ring globules, round globules, irregular-shaped globules, and globule aggregates are δD = 3000-4800, 2900-8100, 2700-11,000, and 2500-11,000‰, respectively. Variations of D/H ratio of these organic globules seemed to be attributed to variations of D/H ratio of the organic radicals or differences of content of the D-rich organic radicals. There are no significant differences in the hydrogen isotopic compositions among the four types of D-rich carbonaceous matter. The D-enrichments suggest that these organic globules have

Spatial and spectral resolution of carbonaceous material from hematite (α-Fe2O3) using multivariate curve resolution-alternating least squares (MCR-ALS) with Raman microspectroscopic mapping: implications for the search for life on Mars.

Science.gov (United States)

Smith, Joseph P; Smith, Frank C; Booksh, Karl S

2017-08-21

The search for evidence of extant or past life on Mars is a primary objective of both the upcoming Mars 2020 rover (NASA) and ExoMars 2020 rover (ESA/Roscosmos) missions. This search will involve the detection and identification of organic molecules and/or carbonaceous material within the Martian surface environment. For the first time on a mission to Mars, the scientific payload for each rover will include a Raman spectrometer, an instrument well-suited for this search. Hematite (α-Fe 2 O 3 ) is a widespread mineral on the Martian surface. The 2LO Raman band of hematite and the Raman D-band of carbonaceous material show spectral overlap, leading to the potential misidentification of hematite as carbonaceous material. Here we report the ability to spatially and spectrally differentiate carbonaceous material from hematite using multivariate curve resolution-alternating least squares (MCR-ALS) applied to Raman microspectroscopic mapping under both 532 nm and 785 nm excitation. For this study, a sample comprised of hematite, carbonaceous material, and substrate-adhesive epoxy in spatially distinct domains was constructed. Principal component analysis (PCA) reveals that both 532 nm and 785 nm excitation produce representative three-phase systems of hematite, carbonaceous material, and substrate-adhesive epoxy in the analyzed sample. MCR-ALS with Raman microspectroscopic mapping using both 532 nm and 785 nm excitation was able to resolve hematite, carbonaceous material, and substrate-adhesive epoxy by generating spatially-resolved chemical maps and corresponding Raman spectra of these spatially distinct chemical species. Moreover, MCR-ALS applied to the combinatorial data sets of 532 nm and 785 nm excitation, which contain hematite and carbonaceous material within the same locations, was able to resolve hematite, carbonaceous material, and substrate-adhesive epoxy. Using multivariate analysis with Raman microspectroscopic mapping, 785 nm excitation more effectively

Destructive hydrogenation. [British patent

Energy Technology Data Exchange (ETDEWEB)

1929-07-15

Liquid or readily liquefiable products are obtained from solid distillable carbonaceous materials such as coals, oil shales or other bituminous substances by subjecting the said initial materials to destructive hydrogenation under mild conditions so that the formation of benzine is substantially avoided, and then subjecting the treated material to extraction by solvents. By hydrogenating under mild conditions the heavy oils which prevent the asphaltic substances from being precipitated are preserved, and the separation of the liquid products from the solid residue is facilitated. Solid paraffins and high boiling point constituents suitable for the production of lubricating oils may be removed before or after the extraction process. The extraction is preferably carried out under pressure with solvents which do not precipitate asphaltic substances. Brown coal containing 11 per cent ash is passed at 450/sup 0/C, and 200 atmospheres pressure in counter current to hydrogen; 40 per cent of the coal is converted into liquid products which are condensed out of the hydrogen stream; the pasty residue, on extraction with benzene, yields 45 per cent of high molecular weight products suitable for the production of lubricating oil.

On thermodynamics of methane+carbonaceous materials adsorption

KAUST Repository

Rahman, Kazi Afzalur

2012-01-01

This study presents the theoretical frameworks for the thermodynamic quantities namely the heat of adsorption, specific heat capacity, entropy, and enthalpy for the adsorption of methane onto various carbonaceous materials. The proposed theoretical frameworks are developed from the rigor of thermodynamic property surfaces of a single component adsorbate-adsorbent system and by incorporating the micropore filling theory approach, where the effect of adsorbed phase volume is considered. The abovementioned thermodynamic properties are quantitatively evaluated from the experimental uptake data for methane adsorption onto activated carbons such as Maxsorb III at temperatures ranging from 120 to 350 K and pressures up to 25 bar. Employing the proposed thermodynamic approaches, this paper shows the thermodynamic maps of the charge and discharge processes of adsorbed natural gas (ANG) storage system for understanding the behaviors of natural gas in ANG vessel. © 2011 Elsevier Ltd. All rights reserved.

Photoelectric work function studies of carbonaceous films containing Ni nanocrystals

International Nuclear Information System (INIS)

Czerwosz, E.; Dluzewski, P.; Kutner, T.; Stacewicz, T.

2003-01-01

In this paper we present the results of photoelectric work function measurements for carbonaceous films containing Ni nanocrystals. The investigated films were obtained by thermal vacuum deposition method. The structure of films was studied by electron diffraction, transmission microscopy and Raman spectroscopy. Film structure depends on Ni contents in the film volume. Work function determined from photoelectric measurements for all investigated films are similar and lie in the range of 2.65-2.93 eV. The decrease of work function value with the cleaning of the film's surface with UV pulsed laser beam was observed

Enantiomer excesses of rare and common sugar derivatives in carbonaceous meteorites

OpenAIRE

Cooper, George; Rios, Andro C.

2016-01-01

The majority of biological sugars and their derivatives contain higher abundances of the “d” mirror-image forms relative to the “l” forms. For example, nucleic acids are composed of only d sugars. Carbonaceous meteorites can potentially assist in understanding the long-sought origin of such phenomena; They preserve a record of the earliest (∼4.5 Gy) chemical processes in the Solar System. To date, there have been no systematic studies of d/l (i.e., enantiomer) ratios of meteoritic sugar deriv...

Direct measurement of oxygen in brown coals and carbochemical products by means of fast neutron analysis

International Nuclear Information System (INIS)

Raeppel, P.; Foerster, H.

1990-01-01

Analyses of elemental oxygen by means of fast neutron activation permit high-accuracy measurements of oxygen concentrations in East German brown coal; this applies to run-of-mine brown coal as well as to demineralized brown coal. The relative error was 4% in the first case and 2% in the latter case. Pre-washing with 1n ammonium acetate solution permits direct analyses of the oxygen bonded to the coal minerals. The method is applicable to other carbonaceous materials, e.g. coal ashes, solid hydrogenation residues, cokes, coal extracts, asphaltenes, oils, etc., at oxygen concentrations of 1-50%. (orig.) [de

Influence of Bulk Carbonaceous Matter on Pluto's Structure and Evolution

Science.gov (United States)

McKinnon, W. B.; Stern, S. A.; Weaver, H. A., Jr.; Spencer, J. R.; Moore, J. M.; Young, L. A.; Olkin, C.

2017-12-01

The rock/ice mass ratio of the Pluto system is about 2/1 (McKinnon et al., Icarus 287, 2017) [1], though this neglects the potential role of bulk carbonaceous matter ("CHON"), an important cometary component and one likely important in the ancestral Kuiper belt. The wealth of measurements at comet 67P/Churyumov-Gerasimenko (a Jupiter-family comet and thus one formed in the same region of the outer Solar System as Pluto) by Rosetta are particularly instructive. E.g., Davidsson et al. (A&A 592, 2016) [2] propose in their "composition A" that 67P/Ch-G is 25% metal/sulfides, 42% rock/organics, and 32% ice by mass. For their assumed component densities, the overall grain density is 1820 kg/m3. Fulle et al. (MNRAS 462, 2016) [3] posit 5 ± 2 volume % Fe-sulfides of density 4600 kg/m3, 28 ± 5% Mg,Fe-olivines and -pyroxenes of density 3200 kg/m3, 52 ± 12% hydrocarbons of density 1200 kg/m3, and 15 ± 6% ices of 917 kg/m3. This composition yields a primordial grain density (dust + ice) of 1885 ± 240 kg/m3. Both of these cometary density estimates [2,3] are consistent with Pluto-Charon, especially as Pluto's uncompressed (STP) density is close to 1820 kg/m3 and that of the system as a whole is close to 1800 kg/m3 [1]. We consider the potential compositional and structural implications of these proposed 67P/Ch-G compositions when applied to Pluto and Charon. The amount of ice in model A of [2] is a good match to Pluto structural models. Their rock/organics component, however, is taken to be half graphite (2000 kg/m3) by volume. The composition in [3] is more divergent: very ice poor, and on the order of 50% light hydrocarbons by volume. Regardless of the differences between [2] and [3], the possibility of massive internal graphite or carbonaceous layers within Pluto is real. We discuss the possible consequences for Pluto's structure, rock/ice ratio, thermal and chemical evolution, and even interpretation of its gravity field from tectonics. For example, radiogenic heat

Characteristics and major sources of carbonaceous aerosols in PM{sub 2.5} from Sanya, China

Energy Technology Data Exchange (ETDEWEB)

Wang, Jingzhi [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Ho, Steven Sai Hang [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Division of Atmospheric Sciences, Desert Research Institute, Reno, NV (United States); Cao, Junji, E-mail: cao@loess.llqg.ac.cn [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Institute of Global Environmental Change, Xi' an Jiaotong University, Xi' an (China); Huang, Rujin [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Laboratory of Atmospheric Chemistry, Paul Scherrer Institute (PSI), 5232 Villigen (Switzerland); Zhou, Jiamao [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); Zhao, Youzhi [College of Science and Technology, Qiongzhou University, Sanya (China); Xu, Hongmei [Department of Environmntal Science and Engineering, Xi' an Jiaotong University, Xi' an (China); Liu, Suixin; Wang, Gehui [Key Lab of Aerosol Chemistry & Physics, Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); State Key Lab of Loess and Quaternary Geology (SKLLQG), Institute of Earth Environment, Chinese Academy of Sciences, Xi' an (China); and others

2015-10-15

PM{sub 2.5} samples were collected in Sanya, China in summer and winter in 2012/2013. Organic carbon (OC), elemental carbon (EC), and non-polar organic compounds including n-alkanes (n-C{sub 14}-n-C{sub 40}) and polycyclic aromatic hydrocarbons (PAHs) were quantified. The concentrations of these carbonaceous matters were generally higher in winter than summer. The estimated secondary organic carbon (OC{sub sec}) accounted for 38% and 54% of the total organic carbon (TOC) in winter and summer, respectively. The higher value of OC{sub sec} in addition to the presences of photochemically-produced PAHs in summer supports that photochemical conversions of organics are much active at the higher air temperatures and with stronger intense solar radiation. Carbon preference index (CPI) and percent contribution of wax n-alkanes suggest that anthropogenic sources were more dominant than derivation from terrestrial plants in Sanya. Diagnostic ratios of atmospheric PAHs further indicate that there was a wide mix of pollution sources in winter while fossil fuel combustion was the most dominant in summer. Positive Matrix Factorization (PMF) analysis with 18 PAHs in the winter samples found that motor vehicle emissions and biomass burning were the two main pollution sources, contributing 37.5% and 24.6% of the total quantified PAHs, respectively. - Highlights: • The first comprehensive study to investigate carbonaceous PM{sub 2.5} in Sanya, China • Higher carbonaceous levels in winter while more SOC formation in summer • Anthropogenic emission is the dominant sources of n-alkanes • Vehicle emission and biomass burning contributed ≥60% of the total PAHs in winter • The result supports better air quality in Sanya than most megacities in China.

Provisional 2008 assessment of solid mineral fuels; Bilan provisoire 2008 des combustibles mineraux solides

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-03-15

This article first comments data on solid mineral fuel consumption in France in 2008, i.e., the overall consumption, and the consumption by different sectors (energy production in coal plants, iron and steel industry, other industries, housing and office buildings). Then, it comments solid mineral fuel imports and their origins. It comments and explains the price evolution since 1999 (notably on the Antwerp-Rotterdam-Amsterdam market) in relationship with maritime transport price, availabilities and problems, and with the evolution of coal demand (notably in China) and oil prices. Finally, it briefly comments the French residual production and stocks.

Ion Irradiation Experiments on the Murchison CM2 Carbonaceous Chondrite: Simulating Space Weathering of Primitive Asteroids

Science.gov (United States)

Keller, L. P.; Christoffersen, R.; Dukes, C. A.; Baragiola, R. A.; Rahman, Z.

2015-01-01

Remote sensing observations show that space weathering processes affect all airless bodies in the Solar System to some degree. Sample analyses and lab experiments provide insights into the chemical, spectroscopic and mineralogic effects of space weathering and aid in the interpretation of remote- sensing data. For example, analyses of particles returned from the S-type asteroid Itokawa by the Hayabusa mission revealed that space-weathering on that body was dominated by interactions with the solar wind acting on LL ordinary chondrite-like materials [1, 2]. Understanding and predicting how the surface regoliths of primitive carbonaceous asteroids respond to space weathering processes is important for future sample return missions (Hayabusa 2 and OSIRIS-REx) that are targeting objects of this type. Here, we report the results of our preliminary ion irradiation experiments on a hydrated carbonaceous chondrite with emphasis on microstructural and infrared spectral changes.

Carbonaceous aerosols and pollutants over Delhi urban environment: Temporal evolution, source apportionment and radiative forcing

Energy Technology Data Exchange (ETDEWEB)

Bisht, D.S. [Indian Institute of Tropical Meteorology, New Delhi (India); Dumka, U.C., E-mail: dumka@aries.res.in [Aryabhatta Research Institute of Observational Sciences, Nainital (India); Kaskaoutis, D.G. [School of Natural Sciences, Shiv Nadar University, Tehsil Dadri (India); Pipal, A.S. [Department of Chemistry, Savitribai Phule Pune University, Pune (India); Srivastava, A.K. [Indian Institute of Tropical Meteorology, New Delhi (India); Soni, V.K.; Attri, S.D.; Sateesh, M. [India Meteorology Department, Lodhi Road, New Delhi (India); Tiwari, S. [Indian Institute of Tropical Meteorology, New Delhi (India)

2015-07-15

Particulate matter (PM{sub 2.5}) samples were collected over Delhi, India during January to December 2012 and analysed for carbonaceous aerosols and inorganic ions (SO{sub 4}{sup 2−} and NO{sub 3}{sup −}) in order to examine variations in atmospheric chemistry, combustion sources and influence of long-range transport. The PM{sub 2.5} samples are measured (offline) via medium volume air samplers and analysed gravimetrically for carbonaceous (organic carbon, OC; elemental carbon, EC) aerosols and inorganic ions (SO{sub 4}{sup 2−} and NO{sub 3}{sup −}). Furthermore, continuous (online) measurements of PM{sub 2.5} (via Beta-attenuation analyser), black carbon (BC) mass concentration (via Magee scientific Aethalometer) and carbon monoxide (via CO-analyser) are carried out. PM{sub 2.5} (online) range from 18.2 to 500.6 μg m{sup −3} (annual mean of 124.6 ± 87.9 μg m{sup −3}) exhibiting higher night-time (129.4 μg m{sup −3}) than daytime (103.8 μg m{sup −3}) concentrations. The online concentrations are 38% and 28% lower than the offline during night and day, respectively. In general, larger night-time concentrations are found for the BC, OC, NO{sub 3}{sup −}and SO{sub 4}{sup 2−}, which are seasonally dependent with larger differences during late post-monsoon and winter. The high correlation (R{sup 2} = 0.74) between OC and EC along with the OC/EC of 7.09 (day time) and 4.55 (night-time), suggest significant influence of biomass-burning emissions (burning of wood and agricultural waste) as well as secondary organic aerosol formation during daytime. Concentrated weighted trajectory (CWT) analysis reveals that the potential sources for the carbonaceous aerosols and pollutants are local emissions within the urban environment and transported smoke from agricultural burning in northwest India during post-monsoon. BC radiative forcing estimates result in very high atmospheric heating rates (~ 1.8–2.0 K day{sup −1}) due to agricultural burning effects

Carbonaceous aerosols and pollutants over Delhi urban environment: Temporal evolution, source apportionment and radiative forcing

International Nuclear Information System (INIS)

Bisht, D.S.; Dumka, U.C.; Kaskaoutis, D.G.; Pipal, A.S.; Srivastava, A.K.; Soni, V.K.; Attri, S.D.; Sateesh, M.; Tiwari, S.

2015-01-01

Particulate matter (PM 2.5 ) samples were collected over Delhi, India during January to December 2012 and analysed for carbonaceous aerosols and inorganic ions (SO 4 2− and NO 3 − ) in order to examine variations in atmospheric chemistry, combustion sources and influence of long-range transport. The PM 2.5 samples are measured (offline) via medium volume air samplers and analysed gravimetrically for carbonaceous (organic carbon, OC; elemental carbon, EC) aerosols and inorganic ions (SO 4 2− and NO 3 − ). Furthermore, continuous (online) measurements of PM 2.5 (via Beta-attenuation analyser), black carbon (BC) mass concentration (via Magee scientific Aethalometer) and carbon monoxide (via CO-analyser) are carried out. PM 2.5 (online) range from 18.2 to 500.6 μg m −3 (annual mean of 124.6 ± 87.9 μg m −3 ) exhibiting higher night-time (129.4 μg m −3 ) than daytime (103.8 μg m −3 ) concentrations. The online concentrations are 38% and 28% lower than the offline during night and day, respectively. In general, larger night-time concentrations are found for the BC, OC, NO 3 − and SO 4 2− , which are seasonally dependent with larger differences during late post-monsoon and winter. The high correlation (R 2 = 0.74) between OC and EC along with the OC/EC of 7.09 (day time) and 4.55 (night-time), suggest significant influence of biomass-burning emissions (burning of wood and agricultural waste) as well as secondary organic aerosol formation during daytime. Concentrated weighted trajectory (CWT) analysis reveals that the potential sources for the carbonaceous aerosols and pollutants are local emissions within the urban environment and transported smoke from agricultural burning in northwest India during post-monsoon. BC radiative forcing estimates result in very high atmospheric heating rates (~ 1.8–2.0 K day −1 ) due to agricultural burning effects during the 2012 post-monsoon season. - Highlights: • Very high PM 2.5 (> 200 µg m −3 ) levels

Constraining Carbonaceous Aerosol Climate Forcing by Bridging Laboratory, Field and Modeling Studies

Science.gov (United States)

Dubey, M. K.; Aiken, A. C.; Liu, S.; Saleh, R.; Cappa, C. D.; Williams, L. R.; Donahue, N. M.; Gorkowski, K.; Ng, N. L.; Mazzoleni, C.; China, S.; Sharma, N.; Yokelson, R. J.; Allan, J. D.; Liu, D.

2014-12-01

Biomass and fossil fuel combustion emits black (BC) and brown carbon (BrC) aerosols that absorb sunlight to warm climate and organic carbon (OC) aerosols that scatter sunlight to cool climate. The net forcing depends strongly on the composition, mixing state and transformations of these carbonaceous aerosols. Complexities from large variability of fuel types, combustion conditions and aging processes have confounded their treatment in models. We analyse recent laboratory and field measurements to uncover fundamental mechanism that control the chemical, optical and microphysical properties of carbonaceous aerosols that are elaborated below: Wavelength dependence of absorption and the single scattering albedo (ω) of fresh biomass burning aerosols produced from many fuels during FLAME-4 was analysed to determine the factors that control the variability in ω. Results show that ω varies strongly with fire-integrated modified combustion efficiency (MCEFI)—higher MCEFI results in lower ω values and greater spectral dependence of ω (Liu et al GRL 2014). A parameterization of ω as a function of MCEFI for fresh BB aerosols is derived from the laboratory data and is evaluated by field data, including BBOP. Our laboratory studies also demonstrate that BrC production correlates with BC indicating that that they are produced by a common mechanism that is driven by MCEFI (Saleh et al NGeo 2014). We show that BrC absorption is concentrated in the extremely low volatility component that favours long-range transport. We observe substantial absorption enhancement for internally mixed BC from diesel and wood combustion near London during ClearFlo. While the absorption enhancement is due to BC particles coated by co-emitted OC in urban regions, it increases with photochemical age in rural areas and is simulated by core-shell models. We measure BrC absorption that is concentrated in the extremely low volatility components and attribute it to wood burning. Our results support

Stabilization of APC residues from waste incineration with ferrous sulfate on a semi-industrial scale

DEFF Research Database (Denmark)

Lundtorp, Kasper; Jensen, Dorthe Lærke; Christensen, Thomas Højlund

2002-01-01

A stabilization method for air pollution control (APC) residues from municipal solid waste incineration (MSWI) involving mixing of the residue with water and FeSO4 has been demonstrated on a semi-industrial scale on three types of APC residues: a semidy (SD) APC residue, a fly ash (FA), and an FA...... mixed with sludge (FAS) from a wet flue gas cleaning system. The process was performed in batches of 165-175 kg residue. It generates a wastewater that is highly saline but has a low content of heavy metals such as Cd, Cr, and Pb. The stabilized and raw residues have been subject to a range of leaching...

Inorganic and carbonaceous components in indoor/outdoor particulate matter in two residential houses in Oslo, Norway.

Science.gov (United States)

Lazaridis, Mihalis; Aleksandropoulou, Victoria; Hanssen, Jan Erik; Dye, Christian; Eleftheriadis, Kostantinos; Katsivela, Eleftheria

2008-03-01

A detailed analysis of indoor/outdoor physicochemical aerosol properties has been performed. Aerosol measurements were taken at two dwellings, one in the city center and the other in the suburbs of the Oslo metropolitan area, during summer/fall and winter/spring periods of 2002-2003. In this paper, emphasis is placed on the chemical characteristics (water-soluble ions and carbonaceous components) of fine (PM2.5) and coarse (PM2.5-10) particles and their indoor/outdoor relationship. Results demonstrate that the carbonaceous species were dominant in all fractions of the PM10 particles (cut off size: 0.09-11.31 microm) during all measurement periods, except winter 2003, when increased concentrations of water-soluble inorganic ions were predominant because of sea salt transport. The concentration of organic carbon was higher in the fine and coarse PM10 fractions indoors, whereas elemental carbon was higher indoors only in the coarse fraction. In regards to the carbonaceous species, local traffic and secondary organic aerosol formation were, probably, the main sources outdoors, whereas indoors combustion activities such as preparation of food, burning of candles, and cigarette smoking were the main sources. In contrast, the concentrations of water-soluble inorganic ions were higher outdoors than indoors. The variability of water-soluble inorganic ion concentrations outdoors was related to changes in emissions from local anthropogenic sources, long-range transport of particles, sea salt emissions, and resuspension of roadside and soil dusts. In the indoor environment the infiltration of the outdoor air indoors was the major source of inorganic ions.

Uso del residual sólido de biogás para la producción de hortalizas en huertos intensivos./Use of biogas solid waste for intensive vegetable production gardens

Directory of Open Access Journals (Sweden)

Pável Chaveli Chávez

2014-01-01

Full Text Available Resumen:Se llevó a cabo un estudio para medir el comportamiento de la utilización de diferentes dosis de residual sólido de producción de biogás (0.5; 1.0; 1.5 y 2.0 kg.m-2 en tres momentos de aplicación (al inicio, cada dos cultivos y en cada cultivo en una secuencia de hortalizas. Se empleó un diseño de bloques al azar con tres repeticiones. Se realizaron muestreos al suelo al término del ciclo de cultivo y se determinó pH (KCl, contenido de fósforo, potasio y el porciento de materia orgánica. Del análisis de los resultados se obtuvo que la dosis de 1 kg.m-2 del residual de biogás en su estado sólido aplicado cada dos cultivos logro incrementos de los rendimientos por encima del 30% con respecto a la no aplicación del residual. Los contenidos de P2O5 y K2O y el % de materia orgánica se favorecieron con el uso del abono al término del ciclo de las hortalizas, lo que permite la explotación intensiva del suelo./Abstract: A study was conducted to measure the performance of using different doses of solid waste in biogas production (0.5, 1.0, 1.5 and 2.0 kg.m-2 in three application times (at baseline, each two crops and in each crop in a sequence of vegetables. Design of randomized blocks with three replications was employed. Soil sampling at the end of the crop cycle were performed and pH (KCl, content of phosphorus, potassium and the percentage of organic matter was determined. Analysis of the results obtained that the dose of 1 kg.m-2 residual biogas in its solid state achievement applied every two crops yield increases above 30% over the non-implementation of the residual. The P2O5 and K2O and % organic matter contents were favored by the use of the organic fertilizer at the end of the cycle of the vegetables, allowing the intensive soil use.

The Biological Potency Of Carbonaceous Nanoparticles Is Associated With The State Of Oxidation Of Surface Carbon Atoms

Science.gov (United States)

Epidemiological studies have shown that exposure to ambient particulate matter (PM) is associated with excess morbidity and mortality. An important component of PM consists of inorganic and organic compounds adsorbed onto a carbonaceous particle core. Toxicological studies indica...

COMBINED THEORETICAL AND EXPERIMENTAL INVESTIGATION OF MECHANISMS AND KINETICS OF VAPOR-PHASE MERCURY UPTAKE BY CARBONACEOUS SURFACES; ANNUAL

International Nuclear Information System (INIS)

Radisav D. Vidic; Eric V. Borguet; Karl J. Johnson

2000-01-01

The overall goal of this research program is to gain fundamental understanding of the important chemistry and physics involved in mercury adsorption on carbonaceous surfaces. This knowledge will then be used to optimize adsorption processes and operating conditions to maximize the uptake of mercury within the required contact time. An additional long-term benefit of this research is the basic understanding of the Hg adsorption process, which may facilitate the design of new adsorbents for more efficient and cost-effective removal of Hg from a variety of effluent streams. Molecular modeling of the adsorption of Hg on carbonaceous surfaces will greatly increase the insight into the physics of the adsorption process and combined with in situ rate measurements of mercury adsorption and desorption (conventional and pulsed laser) on graphite using linear and nonlinear optical probes with real time optical resolution have the potential to provide fundamental insight into the process of mercury uptake by carbonaceous surfaces. Besides accurate assessment of key parameters influencing adsorption equilibrium, fundamental understanding of the kinetics of mercury adsorption, desorption, and diffusion will be developed in this study. These key physical and chemical processes postulated through molecular modeling efforts and verified by in situ measurements will be utilized to select (or develop) promising sorbents for mercury control, which will be tested under dynamic conditions using simulated flue gas

Long-term stabilization of crop residues and soil organic carbon affected by residue quality and initial soil pH.

Science.gov (United States)

Wang, Xiaojuan; Butterly, Clayton R; Baldock, Jeff A; Tang, Caixian

2017-06-01

Residues differing in quality and carbon (C) chemistry are presumed to contribute differently to soil pH change and long-term soil organic carbon (SOC) pools. This study examined the liming effect of different crop residues (canola, chickpea and wheat) down the soil profile (0-30cm) in two sandy soils differing in initial pH as well as the long-term stability of SOC at the amended layer (0-10cm) using mid-infrared (MIR) and solid-state 13 C nuclear magnetic resonance (NMR) spectroscopy. A field column experiment was conducted for 48months. Chickpea- and canola-residue amendments increased soil pH at 0-10cm in the Podzol by up to 0.47 and 0.36units, and in the Cambisol by 0.31 and 0.18units, respectively, at 48months when compared with the non-residue-amended control. The decomposition of crop residues was greatly retarded in the Podzol with lower initial soil pH during the first 9months. The MIR-predicted particulate organic C (POC) acted as the major C sink for residue-derived C in the Podzol. In contrast, depletion of POC and recovery of residue C in MIR-predicted humic organic C (HOC) were detected in the Cambisol within 3months. Residue types showed little impact on total SOC and its chemical composition in the Cambisol at 48months, in contrast to the Podzol. The final HOC and resistant organic C (ROC) pools in the Podzol amended with canola and chickpea residues were about 25% lower than the control. This apparent priming effect might be related to the greater liming effect of these two residues in the Podzol. Copyright © 2017 Elsevier B.V. All rights reserved.

Forensic analysis of high explosives residues in post-blast water samples employing solid phase extraction for analyte pro-concentration

International Nuclear Information System (INIS)

Umi Kalsom Ahmad; Rajendran, Sumathy; Ling, Lee Woan

2008-01-01

Nitro aromatic, nitramine and nitrate ester compounds are a major group of high order explosive or better known as military explosives. Octahydro-1,3,5,7-tetrazocine (HMX), 1,3,5-hexahydro-1,3,5-trinitro triazine (RDX), 2,4,6-trinitro-toluene (TNT), pentaerythritol tetranitrate (PETN) and 2,4-dinitrotoluene (2,4-DNT) are secondary high explosives classified as most commonly used explosives components. There is an increasing demand for pre-concentration of these compounds in water samples as the sensitivity achieved by instrumental analytical methods for these high explosives residues are the main drawback in the application at trace levels for forensic analysis. Hence, a simple cartridge solid phase extraction (SPE) procedure was optimized as the off-line extraction and pre-concentration method to enhance the detection limit of high explosive residues using micellar electrokinetic chromatography (MEKC) and gas chromatography with electron-capture detection (GC-ECD) methods. The SPE cartridges utilized LiChrolut EN as the SPE adsorbent. By emplying pre-concentration using SPE, the detection limits of the target analytes in water sample were lowered by more than 1000 times with good percentage recovery (>87%) for MEKC method and lowered by 120 times with more than 2 % percentage recovery for GC-ECD methods. In order to test the feasibility of the developed method to real cases, post-blast water samples were analyzed. The post-blast water samples which were collected from Baling Bom training range, Ulu Kinta, Perak contained RDX and PETN in the range of 0.05 - 0.17 ppm and 0.0124 - 0.0390 ppm respectively. (author)

[Monitoring of the residue of fosthiazate in water samples using solid-phase extraction coupled with gas chromatography/mass spectrometry].

Science.gov (United States)

Zhu, Jing; Zhou, Xin; Fu, Chunmei; Liu, Sankang; Li, Zhangwan

2004-11-01

Solid-phase extraction (SPE) coupled with gas chromatography/mass spectrometry (GC/MS) was used to determine the fosthiazate residue in water samples. The water samples were first filtered through cellulose filters (0.45 microm pore size). A 100 mL volume of filtered water, in which 1 mL of methanol has been added, was then passed through a pre-conditioned 3 cm C18 cartridge at a flow-rate of 1.5 mL/min. Elution was performed by 1 mL of methanol. The eluant was finally dried under reduced pressure for solvent evaporation. The volume was quantitatively adjusted to 0.5 mL with methanol. The analysis was carried out on GC/MS. The mass spectrometer was operated in selected ion monitoring (SIM) mode. According to mass spectrum of fosthiazate, three selected ions at m/z of 126, 195, 283, respectively, were monitored for identification and quantification. High sensitivity and selectivity were achieved by using this method. The limit of detection for fosthiazate in water samples was determined to be 56.4 ng/L. The linearity was demonstrated over a wide range of concentrations covering from 0.282 to 141 microg/L. The recoveries were more than 85.5% and the relative standard deviations for the overall procedure were less than 4.42%. The fosthiazate residue was detected in the water samples from a pool near cropland where fosthiazate was used. The results demonstrate the suitability of the SPE-GC/MS approach for the analysis of fosthiazate in water.

Characterization of oil shale, isolated kerogen, and post-pyrolysis residues using advanced 13 solid-state nuclear magnetic resonance spectroscopy

Science.gov (United States)

Cao, Xiaoyan; Birdwell, Justin E.; Chappell, Mark A.; Li, Yuan; Pignatello, Joseph J.; Mao, Jingdong

2013-01-01

Characterization of oil shale kerogen and organic residues remaining in postpyrolysis spent shale is critical to the understanding of the oil generation process and approaches to dealing with issues related to spent shale. The chemical structure of organic matter in raw oil shale and spent shale samples was examined in this study using advanced solid-state 13C nuclear magnetic resonance (NMR) spectroscopy. Oil shale was collected from Mahogany zone outcrops in the Piceance Basin. Five samples were analyzed: (1) raw oil shale, (2) isolated kerogen, (3) oil shale extracted with chloroform, (4) oil shale retorted in an open system at 500°C to mimic surface retorting, and (5) oil shale retorted in a closed system at 360°C to simulate in-situ retorting. The NMR methods applied included quantitative direct polarization with magic-angle spinning at 13 kHz, cross polarization with total sideband suppression, dipolar dephasing, CHn selection, 13C chemical shift anisotropy filtering, and 1H-13C long-range recoupled dipolar dephasing. The NMR results showed that, relative to the raw oil shale, (1) bitumen extraction and kerogen isolation by demineralization removed some oxygen-containing and alkyl moieties; (2) unpyrolyzed samples had low aromatic condensation; (3) oil shale pyrolysis removed aliphatic moieties, leaving behind residues enriched in aromatic carbon; and (4) oil shale retorted in an open system at 500°C contained larger aromatic clusters and more protonated aromatic moieties than oil shale retorted in a closed system at 360°C, which contained more total aromatic carbon with a wide range of cluster sizes.

Hanford Tank 241-S-112 Residual Waste Composition and Leach Test Data

Energy Technology Data Exchange (ETDEWEB)

Cantrell, Kirk J.; Krupka, Kenneth M.; Geiszler, Keith N.; Lindberg, Michael J.; Arey, Bruce W.; Schaef, Herbert T.

2008-08-29

This report presents the results of laboratory characterization and testing of two samples (designated 20406 and 20407) of residual waste collected from tank S-112 after final waste retrieval. These studies were completed to characterize the residual waste and assess the leachability of contami¬nants from the solids. This is the first report from this PNNL project to describe the composition and leach test data for residual waste from a salt cake tank. All previous PNNL reports (Cantrell et al. 2008; Deutsch et al. 2006, 2007a, 2007b, 2007c) describing contaminant release models, and characterization and testing results for residual waste in single-shell tanks were based on samples from sludge tanks.

Identifying inter-residue resonances in crowded 2D {sup 13}C-{sup 13}C chemical shift correlation spectra of membrane proteins by solid-state MAS NMR difference spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Miao Yimin; Cross, Timothy A. [Florida State University, Department of Chemistry and Biochemistry (United States); Fu Riqiang, E-mail: rfu@magnet.fsu.edu [National High Magnet Field Lab (United States)

2013-07-15

The feasibility of using difference spectroscopy, i.e. subtraction of two correlation spectra at different mixing times, for substantially enhanced resolution in crowded two-dimensional {sup 13}C-{sup 13}C chemical shift correlation spectra is presented. With the analyses of {sup 13}C-{sup 13}C spin diffusion in simple spin systems, difference spectroscopy is proposed to partially separate the spin diffusion resonances of relatively short intra-residue distances from the longer inter-residue distances, leading to a better identification of the inter-residue resonances. Here solid-state magic-angle-spinning NMR spectra of the full length M2 protein embedded in synthetic lipid bilayers have been used to illustrate the resolution enhancement in the difference spectra. The integral membrane M2 protein of Influenza A virus assembles as a tetrameric bundle to form a proton-conducting channel that is activated by low pH and is essential for the viral lifecycle. Based on known amino acid resonance assignments from amino acid specific labeled samples of truncated M2 sequences or from time-consuming 3D experiments of uniformly labeled samples, some inter-residue resonances of the full length M2 protein can be identified in the difference spectra of uniformly {sup 13}C labeled protein that are consistent with the high resolution structure of the M2 (22-62) protein (Sharma et al., Science 330(6003):509-512, 2010)

Characterization of Hospital Residuals; Caracterizacion de Residuos Hospitalarios

Energy Technology Data Exchange (ETDEWEB)

Blanco Meza, A; Bonilla Jimenez, S

1997-07-01

The main objective of this investigation is the characterization of the solid residuals. A description of the handling of the liquid and gassy waste generated in hospitals is also given, identifying the source where they originate. To achieve the proposed objective the work was divided in three stages: The first one was the planning and the coordination with each hospital center, in this way, to determine the schedule of gathering of the waste can be possible. In the second stage a fieldwork was made; it consisted in gathering the quantitative and qualitative information of the general state of the handling of residuals. In the third and last stage, the information previously obtained was organized to express the results as the production rate per day by bed, generation of solid residuals for sampled services, type of solid residuals and density of the same ones. With the obtained results, approaches are settled down to either determine design parameters for final disposition whether for incineration, trituration, sanitary filler or recycling of some materials, and storage politics of the solid residuals that allow to determine the gathering frequency. The study concludes that it is necessary to improve the conditions of the residuals handling in some aspects, to provide the cleaning personnel of the equipment for gathering disposition and of security, minimum to carry out this work efficiently, and to maintain a control of all the dangerous waste, like sharp or polluted materials. In this way, an appreciable reduction is guaranteed in the impact on the atmosphere. (Author) [Spanish] El objetivo principal de esta investigacion es la caracterizacion de los residuos solidos. Se da tambien una descripcion del manejo de los desechos liquidos y gaseosos generados en hospitales, identificando la fuente donde se originan. Para lograr el objetivo propuesto se dividio el trabajo en tres etapas; la primera fue el planeamiento y la coordinacion con cada centro hospitalario

Biogas Production from Energy Crops and Agriculture Residues

DEFF Research Database (Denmark)

Wang, Guangtao

and wet explosion pretreated energy crops and agriculture residues with swine manure at various volatile solids (VS) ratio between crop and manure was carried out by batch tests and continuous experiments. The efficiency of the co-digestion experiment was evaluated based on (a) the methane potential......In this thesis, the feasibility of utilizing energy crops (willow and miscanthus) and agriculture residues (wheat straw and corn stalker) in an anaerobic digestion process for biogas production was evaluated. Potential energy crops and agriculture residues were screened according...... of perennial crops was tested as a storage method and pretreatment method for enhancement of the biodegradability of the crops. The efficiency of the silage process was evaluated based on (a) the amount of biomass loss during storage and (b) the effect of the silage on methane potential. Co-digestion of raw...

Contaminant interferences with SIMS analyses of microparticle impactor residues on LDEF surfaces

International Nuclear Information System (INIS)

Simon, C.G.; Batchelor, D.; Griffis, D.P.; Hunter, J.L.; Misra, V.; Ricks, D.A.; Wortman, J.J.

1992-01-01

Elemental analyses of impactor residues on high purity surface exposed to the low earth orbit (LEO) environment for 5.8 years on Long Duration Exposure Facility (LDEF) has revealed several probable sources for microparticles at this altitude, including natural micrometeorites and manmade debris ranging from paint pigments to bits of stainless steel. A myriad of contamination interferences were identified and their effects on impactor debris identification mitigated during the course of this study. These interferences included pre-, post-, and in-flight deposited particulate surface contaminants, as well as indigenous heterogeneous material contaminants. Non-flight contaminants traced to human origins, including spittle and skin oils, contributed significant levels of alkali-rich carbonaceous interferences. A ubiquitous layer of in-flight deposited silicaceous contamination varied in thickness with location on LDEF and proximity to active electrical fields. In-flight deposited (low velocity) contaminants included urine droplets and bits of metal film from eroded thermal blankets

Treatment of waste incinerator air-pollution-control residues with FeSO4: Laboratory investigation of design parameters

DEFF Research Database (Denmark)

Jensen, Dorthe Lærke; Christensen, Thomas Højlund; Lundtorp, Kasper

2002-01-01

supplied, the liquid-to-solid ratio of the process, the separation of solids and wastewater, the sequence of material mixing, the possibilities of reuse of water, the feasibility of using secondary (brackish) water, and simple means to improve the wastewater quality. The investigation showed...... that an optimum process configuration could be obtained yielding a stabilised solid product with low leaching of heavy metals and a dischargable wastewater with high contents of salts (in order to remove salts from the solid product) and low concentrations of heavy metals. The amount of iron added to the APC......The key design parameters of a new process for treatment of air-pollution-control (APC) residues (the Ferroxprocess) were investigated in the laboratory. The optimisation involved two different APC-residues from actual incinerator plants. The design parameters considered were: amount of iron oxide...

Methods for purifying carbon materials

Science.gov (United States)

Dailly, Anne [Pasadena, CA; Ahn, Channing [Pasadena, CA; Yazami, Rachid [Los Angeles, CA; Fultz, Brent T [Pasadena, CA

2009-05-26

Methods of purifying samples are provided that are capable of removing carbonaceous and noncarbonaceous impurities from a sample containing a carbon material having a selected structure. Purification methods are provided for removing residual metal catalyst particles enclosed in multilayer carbonaceous impurities in samples generate by catalytic synthesis methods. Purification methods are provided wherein carbonaceous impurities in a sample are at least partially exfoliated, thereby facilitating subsequent removal of carbonaceous and noncarbonaceous impurities from the sample. Methods of purifying carbon nanotube-containing samples are provided wherein an intercalant is added to the sample and subsequently reacted with an exfoliation initiator to achieve exfoliation of carbonaceous impurities.

Long-term (2001-2012) trends of carbonaceous aerosols from a remote island in the western North Pacific: an outflow region of Asian pollutants

Science.gov (United States)

Boreddy, Suresh K. R.; Mozammel Haque, M.; Kawamura, Kimitaka

2018-01-01

The present study reports on long-term trends of carbonaceous aerosols in total suspended particulate (TSP) samples collected at Chichijima in the western North Pacific during 2001-2012. Seasonal variations of elemental carbon (EC), organic carbon (OC), and water-soluble organic carbon (WSOC) concentrations showed maxima in winter to spring and minima in summer. These seasonal differences in the concentrations of carbonaceous aerosols were associated with the outflows of polluted air masses from East Asia, which are clearly distinguishable from pristine air masses from the central Pacific. The higher concentrations of carbonaceous aerosols during winter to spring are associated with long-range atmospheric transport of East Asian continental polluted air masses, whereas lower concentrations may be due to pristine air masses from the central Pacific in summer. The annual trends of OC / EC (+0.46 % yr-1), WSOC (+0.18 % yr-1) and WSOC / OC (+0.08 % yr-1) showed significant (p Asia.

Preparation of a novel carbon-based solid acid from cassava stillage residue and its use for the esterification of free fatty acids in waste cooking oil.