Sampling for validation of digital soil maps

NARCIS (Netherlands)

Brus, D.J.; Kempen, B.; Heuvelink, G.B.M.

2011-01-01

The increase in digital soil mapping around the world means that appropriate and efficient sampling strategies are needed for validation. Data used for calibrating a digital soil mapping model typically are non-random samples. In such a case we recommend collection of additional independent data and

Monitoring PCDD/Fs in soil and herbage samples collected in the neighborhood of a hazardous waste incinerator after five years of operation

Energy Technology Data Exchange (ETDEWEB)

Nadal, M.; Bocio, A.; Schuhmacher, M.; Liobet, J.M.; Domingo, J.L. [Rovira i Virgili Univ., Reus (Spain); Diaz-Ferrero, J. [Inst. Quimic de Sarria, Barcelona (Spain)

2004-09-15

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) are among the most dangerous environmental pollutants, usually generated during combustion processes. Until recently, waste incineration was widely referenced as one of the most important sources of PCDD/F release to the atmosphere. In 1999, the only hazardous waste incinerator (HWI) in Spain began regular operations. This facility is placed in Tarragona, Catalonia. The presence of this HWI, as well as that of a municipal solid waste incinerator (MSWI) at a few kilometers, increased the concern of the public opinion in relation to the potential toxic emissions, especially those of metals and PCDD/Fs, which could affect the health of the population living in the area. Previously to regular operations (1996) the baseline levels of PCDD/Fs in soil and vegetation samples collected near the HWI were determined. A second survey was carried out two years later (1998) in order to establish the temporal variation in PCDD/F concentrations in soil and vegetation samples taken at the same sampling points. Vegetation is considered an adequate short-term environmental monitor for PCDD/Fs. Therefore, in the surveillance program of the facility (1999-2003), herbage samples (40) were annually collected at the same sampling points in which baseline samples had been taken. Moreover, considering soil as a suitable long-term monitor for PCDD/Fs, 40 soil samples in this matrix were again collected in 2001 and 2003 to examine the temporal variations of PCDD/F levels in the area. In the present study, we present the concentrations of PCDD/Fs in soil and vegetation samples collected in the vicinity of the HWI after 5 years of regular operations.

Radiometric assessment of natural radioactivity levels of agricultural soil samples collected in Dakahlia, Egypt.

Science.gov (United States)

Issa, Shams A M

2013-01-01

Determination of the natural radioactivity has been carried out, by using a gamma-ray spectrometry [NaI (Tl) 3″ × 3″] system, in surface soil samples collected from various locations in Dakahlia governorate, Egypt. These locations form the agriculturally important regions of Egypt. The study area has many industries such as chemical, paper, organic fertilisers and construction materials, and the soils of the study region are used as a construction material. Therefore, it becomes necessary to study the natural radioactivity levels in soil to assess the dose for the population in order to know the health risks. The activity concentrations of (226)Ra, (232)Th and (40)K in the soil ranged from 5.7 ± 0.3 to 140 ± 7, from 9.0 ± 0.4 to 139 ± 7 and from 22 ± 1 to 319 ± 16 Bq kg(-1), respectively. The absorbed dose rate, annual effective dose rate, radium equivalent (Req), excess lifetime cancer risk, hazard indices (Hex and Hin) and annual gonadal dose equivalent, which resulted from the natural radionuclides in the soil were calculated.

Soil Gas Sampling Operating Procedure

Science.gov (United States)

EPA Region 4 Science and Ecosystem Support Division (SESD) document that describes general and specific procedures, methods, and considerations when collecting soil gas samples for field screening or laboratory analysis.

Large zero-tension plate lysimeters for soil water and solute collection in undisturbed soils

Directory of Open Access Journals (Sweden)

A. Peters

2009-09-01

Full Text Available Water collection from undisturbed unsaturated soils to estimate in situ water and solute fluxes in the field is a challenge, in particular if soils are heterogeneous. Large sampling devices are required if preferential flow paths are present. We present a modular plate system that allows installation of large zero-tension lysimeter plates under undisturbed soils in the field. To investigate the influence of the lysimeter on the water flow field in the soil, a numerical 2-D simulation study was conducted for homogeneous soils with uni- and bimodal pore-size distributions and stochastic Miller-Miller heterogeneity. The collection efficiency was found to be highly dependent on the hydraulic functions, infiltration rate, and lysimeter size, and was furthermore affected by the degree of heterogeneity. In homogeneous soils with high saturated conductivities the devices perform poorly and even large lysimeters (width 250 cm can be bypassed by the soil water. Heterogeneities of soil hydraulic properties result into a network of flow channels that enhance the sampling efficiency of the lysimeter plates. Solute breakthrough into zero-tension lysimeter occurs slightly retarded as compared to the free soil, but concentrations in the collected water are similar to the mean flux concentration in the undisturbed soil. To validate the results from the numerical study, a dual tracer study with seven lysimeters of 1.25×1.25 m area was conducted in the field. Three lysimeters were installed underneath a 1.2 m filling of contaminated silty sand, the others deeper in the undisturbed soil. The lysimeters directly underneath the filled soil material collected water with a collection efficiency of 45%. The deeper lysimeters did not collect any water. The arrival of the tracers showed that almost all collected water came from preferential flow paths.

Sampling soils for 137Cs using various field-sampling volumes

International Nuclear Information System (INIS)

Nyhan, J.W.; Schofield, T.G.; White, G.C.; Trujillo, G.

1981-10-01

The sediments from a liquid effluent receiving area at the Los Alamos National Laboratory and soils from intensive study area in the fallout pathway of Trinity were sampled for 137 Cs using 25-, 500-, 2500-, and 12 500-cm 3 field sampling volumes. A highly replicated sampling program was used to determine mean concentrations and inventories of 137 Cs at each site, as well as estimates of spatial, aliquoting, and counting variance components of the radionuclide data. The sampling methods were also analyzed as a function of soil size fractions collected in each field sampling volume and of the total cost of the program for a given variation in the radionuclide survey results. Coefficients of variation (CV) of 137 Cs inventory estimates ranged from 0.063 to 0.14 for Mortandad Canyon sediments, where CV values for Trinity soils were observed from 0.38 to 0.57. Spatial variance components of 137 Cs concentration data were usually found to be larger than either the aliquoting or counting variance estimates and were inversely related to field sampling volume at the Trinity intensive site. Subsequent optimization studies of the sampling schemes demonstrated that each aliquot should be counted once, and that only 2 to 4 aliquots out of an many as 30 collected need be assayed for 137 Cs. The optimization studies showed that as sample costs increased to 45 man-hours of labor per sample, the variance of the mean 137 Cs concentration decreased dramatically, but decreased very little with additional labor

Soil sampling strategies: Evaluation of different approaches

Energy Technology Data Exchange (ETDEWEB)

De Zorzi, Paolo [Agenzia per la Protezione dell' Ambiente e per i Servizi Tecnici (APAT), Servizio Metrologia Ambientale, Via di Castel Romano, 100-00128 Roma (Italy)], E-mail: paolo.dezorzi@apat.it; Barbizzi, Sabrina; Belli, Maria [Agenzia per la Protezione dell' Ambiente e per i Servizi Tecnici (APAT), Servizio Metrologia Ambientale, Via di Castel Romano, 100-00128 Roma (Italy); Mufato, Renzo; Sartori, Giuseppe; Stocchero, Giulia [Agenzia Regionale per la Prevenzione e Protezione dell' Ambiente del Veneto, ARPA Veneto, U.O. Centro Qualita Dati, Via Spalato, 14-36045 Vicenza (Italy)

2008-11-15

The National Environmental Protection Agency of Italy (APAT) performed a soil sampling intercomparison, inviting 14 regional agencies to test their own soil sampling strategies. The intercomparison was carried out at a reference site, previously characterised for metal mass fraction distribution. A wide range of sampling strategies, in terms of sampling patterns, type and number of samples collected, were used to assess the mean mass fraction values of some selected elements. The different strategies led in general to acceptable bias values (D) less than 2{sigma}, calculated according to ISO 13258. Sampling on arable land was relatively easy, with comparable results between different sampling strategies.

Soil sampling strategies: Evaluation of different approaches

International Nuclear Information System (INIS)

De Zorzi, Paolo; Barbizzi, Sabrina; Belli, Maria; Mufato, Renzo; Sartori, Giuseppe; Stocchero, Giulia

2008-01-01

The National Environmental Protection Agency of Italy (APAT) performed a soil sampling intercomparison, inviting 14 regional agencies to test their own soil sampling strategies. The intercomparison was carried out at a reference site, previously characterised for metal mass fraction distribution. A wide range of sampling strategies, in terms of sampling patterns, type and number of samples collected, were used to assess the mean mass fraction values of some selected elements. The different strategies led in general to acceptable bias values (D) less than 2σ, calculated according to ISO 13258. Sampling on arable land was relatively easy, with comparable results between different sampling strategies

Soil sampling strategies: evaluation of different approaches.

Science.gov (United States)

de Zorzi, Paolo; Barbizzi, Sabrina; Belli, Maria; Mufato, Renzo; Sartori, Giuseppe; Stocchero, Giulia

2008-11-01

The National Environmental Protection Agency of Italy (APAT) performed a soil sampling intercomparison, inviting 14 regional agencies to test their own soil sampling strategies. The intercomparison was carried out at a reference site, previously characterised for metal mass fraction distribution. A wide range of sampling strategies, in terms of sampling patterns, type and number of samples collected, were used to assess the mean mass fraction values of some selected elements. The different strategies led in general to acceptable bias values (D) less than 2sigma, calculated according to ISO 13258. Sampling on arable land was relatively easy, with comparable results between different sampling strategies.

How to Perform Precise Soil and Sediment Sampling? One solution: The Fine Increment Soil Collector (FISC)

Energy Technology Data Exchange (ETDEWEB)

Mabit, L.; Toloza, A. [Soil and Water Management and Crop Nutrition Laboratory, IAEA, Seibersdorf (Austria); Meusburger, K.; Alewell, C. [Environmental Geosciences, Department of Environmental Sciences, University of Basel, Basel (Switzerland); Iurian, A-R. [Babes-Bolyai University, Faculty of Environmental Science and Engineering, Cluj-Napoca (Romania); Owens, P. N. [Environmental Science Program and Quesnel River Research Centre, University of Northern British Columbia, Prince George, British Columbia (Canada)

2014-07-15

Soil and sediment related research for terrestrial agrienvironmental assessments requires accurate depth incremental sampling to perform detailed analysis of physical, geochemical and biological properties of soil and exposed sediment profiles. Existing equipment does not allow collecting soil/sediment increments at millimetre resolution. The Fine Increment Soil Collector (FISC), developed by the SWMCN Laboratory, allows much greater precision in incremental soil/sediment sampling. It facilitates the easy recovery of collected material by using a simple screw-thread extraction system (see Figure 1). The FISC has been designed specifically to enable standardized scientific investigation of shallow soil/sediment samples. In particular, applications have been developed in two IAEA Coordinated Research Projects (CRPs): CRP D1.20.11 on “Integrated Isotopic Approaches for an Area-wide Precision Conservation to Control the Impacts of Agricultural Practices on Land Degradation and Soil Erosion” and CRP D1.50.15 on “Response to Nuclear Emergencies Affecting Food and Agriculture.”.

How to Perform Precise Soil and Sediment Sampling? One solution: The Fine Increment Soil Collector (FISC)

International Nuclear Information System (INIS)

Mabit, L.; Toloza, A.; Meusburger, K.; Alewell, C.; Iurian, A-R.; Owens, P.N.

2014-01-01

Soil and sediment related research for terrestrial agrienvironmental assessments requires accurate depth incremental sampling to perform detailed analysis of physical, geochemical and biological properties of soil and exposed sediment profiles. Existing equipment does not allow collecting soil/sediment increments at millimetre resolution. The Fine Increment Soil Collector (FISC), developed by the SWMCN Laboratory, allows much greater precision in incremental soil/sediment sampling. It facilitates the easy recovery of collected material by using a simple screw-thread extraction system (see Figure 1). The FISC has been designed specifically to enable standardized scientific investigation of shallow soil/sediment samples. In particular, applications have been developed in two IAEA Coordinated Research Projects (CRPs): CRP D1.20.11 on “Integrated Isotopic Approaches for an Area-wide Precision Conservation to Control the Impacts of Agricultural Practices on Land Degradation and Soil Erosion” and CRP D1.50.15 on “Response to Nuclear Emergencies Affecting Food and Agriculture.”

Soil Sampling Plan for the transuranic storage area soil overburden and final report: Soil overburden sampling at the RWMC transuranic storage area

International Nuclear Information System (INIS)

Stanisich, S.N.

1994-12-01

This Soil Sampling Plan (SSP) has been developed to provide detailed procedural guidance for field sampling and chemical and radionuclide analysis of selected areas of soil covering waste stored at the Transuranic Storage Area (TSA) at the Idaho National Engineering Laboratory's (INEL) Radioactive Waste Management Complex (RWMC). The format and content of this SSP represents a complimentary hybrid of INEL Waste Management--Environmental Restoration Program, and Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) Remedial Investigation/Feasibility Study (RI/FS) sampling guidance documentation. This sampling plan also functions as a Quality Assurance Project Plan (QAPP). The QAPP as a controlling mechanism during sampling to ensure that all data collected are valid, reliabile, and defensible. This document outlines organization, objectives and quality assurance/quality control (QA/QC) activities to achieve the desired data quality goals. The QA/QC requirements for this project are outlined in the Data Collection Quality Assurance Plan (DCQAP) for the Buried Waste Program. The DCQAP is a program plan and does not outline the site specific requirements for the scope of work covered by this SSP

Saturation and porosity measurements of different soil samples by gamma ray transmission

International Nuclear Information System (INIS)

Akbal, S.; Filiz Baytas, A.

2000-01-01

Gamma-ray transmission methods have been used accurately for the study of the properties of soil samples. In this study, the soil samples were collected from various regions of Turkey and a Nal (TI) detector measured the attenuation of strongly collimated monoenergetic gamma beam (from Cs-137) through soil samples. The water saturation and porosity were therefore calculated from the transmission measurements for each soil sample. (authors)

Degradation of hydrocarbons in soil samples analyzed within accepted analytical holding times

International Nuclear Information System (INIS)

Jackson, J.; Thomey, N.; Dietlein, L.F.

1992-01-01

Samples which are collected in conjunction with subsurface investigations at leaking petroleum storage tank sites and petroleum refineries are routinely analyzed for benzene, toluene, ethylbenzene, xylenes (BTEX), and total petroleum hydrocarbons (TPH). Water samples are preserved by the addition of hydrochloric acid and maintained at four degrees centigrade prior to analysis. This is done to prevent bacterial degradation of hydrocarbons. Chemical preservation is not presently performed on soil samples. Instead, the samples are cooled and maintained at four degrees centigrade. This study was done to measure the degree of degradation of hydrocarbons in soil samples which are analyzed within accepted holding times. Soil samples were collected and representative subsamples were prepared from the initial sample. Subsamples were analyzed in triplicate for BTEX and TPH throughout the length of the approved holding times to measure the extent of sample constituent degradation prior to analysis. Findings imply that for sandy soils, BTEX and TPH concentrations can be highly dependent upon the length of time which elapses between sample collection and analysis

Standard operating procedures for collection of soil and sediment samples for the Sediment-bound Contaminant Resiliency and Response (SCoRR) strategy pilot study

Science.gov (United States)

Fisher, Shawn C.; Reilly, Timothy J.; Jones, Daniel K.; Benzel, William M.; Griffin, Dale W.; Loftin, Keith A.; Iwanowicz, Luke R.; Cohl, Jonathan A.

2015-12-17

An understanding of the effects on human and ecological health brought by major coastal storms or flooding events is typically limited because of a lack of regionally consistent baseline and trends data in locations proximal to potential contaminant sources and mitigation activities, sensitive ecosystems, and recreational facilities where exposures are probable. In an attempt to close this gap, the U.S. Geological Survey (USGS) has implemented the Sediment-bound Contaminant Resiliency and Response (SCoRR) strategy pilot study to collect regional sediment-quality data prior to and in response to future coastal storms. The standard operating procedure (SOP) detailed in this document serves as the sample-collection protocol for the SCoRR strategy by providing step-by-step instructions for site preparation, sample collection and processing, and shipping of soil and surficial sediment (for example, bed sediment, marsh sediment, or beach material). The objectives of the SCoRR strategy pilot study are (1) to create a baseline of soil-, sand-, marsh sediment-, and bed-sediment-quality data from sites located in the coastal counties from Maine to Virginia based on their potential risk of being contaminated in the event of a major coastal storm or flooding (defined as Resiliency mode); and (2) respond to major coastal storms and flooding by reoccupying select baseline sites and sampling within days of the event (defined as Response mode). For both modes, samples are collected in a consistent manner to minimize bias and maximize quality control by ensuring that all sampling personnel across the region collect, document, and process soil and sediment samples following the procedures outlined in this SOP. Samples are analyzed using four USGS-developed screening methods—inorganic geochemistry, organic geochemistry, pathogens, and biological assays—which are also outlined in this SOP. Because the SCoRR strategy employs a multi-metric approach for sample analyses, this

Optimizing Soil Moisture Sampling Locations for Validation Networks for SMAP

Science.gov (United States)

Roshani, E.; Berg, A. A.; Lindsay, J.

2013-12-01

Soil Moisture Active Passive satellite (SMAP) is scheduled for launch on Oct 2014. Global efforts are underway for establishment of soil moisture monitoring networks for both the pre- and post-launch validation and calibration of the SMAP products. In 2012 the SMAP Validation Experiment, SMAPVEX12, took place near Carman Manitoba, Canada where nearly 60 fields were sampled continuously over a 6 week period for soil moisture and several other parameters simultaneous to remotely sensed images of the sampling region. The locations of these sampling sites were mainly selected on the basis of accessibility, soil texture, and vegetation cover. Although these criteria are necessary to consider during sampling site selection, they do not guarantee optimal site placement to provide the most efficient representation of the studied area. In this analysis a method for optimization of sampling locations is presented which combines the state-of-art multi-objective optimization engine (non-dominated sorting genetic algorithm, NSGA-II), with the kriging interpolation technique to minimize the number of sampling sites while simultaneously minimizing the differences between the soil moisture map resulted from the kriging interpolation and soil moisture map from radar imaging. The algorithm is implemented in Whitebox Geospatial Analysis Tools, which is a multi-platform open-source GIS. The optimization framework is subject to the following three constraints:. A) sampling sites should be accessible to the crew on the ground, B) the number of sites located in a specific soil texture should be greater than or equal to a minimum value, and finally C) the number of sampling sites with a specific vegetation cover should be greater than or equal to a minimum constraint. The first constraint is implemented into the proposed model to keep the practicality of the approach. The second and third constraints are considered to guarantee that the collected samples from each soil texture categories

Cesium-137 and natural radionuclides in soils from southern Brazil and soils and others environmental samples from Antarctic

International Nuclear Information System (INIS)

Schuch, L.A.

1993-04-01

This work presents a study of environmental artificial and natural radioactivity levels in soil samples from the Southern Brazil and in soils and other environmental samples form Antarctica. Artificial radioactivity was determined by measuring Cs-137 which is a 30.1 year half-life man-made radionuclide produced in the past by atmospheric tests of nuclear weapons. Natural radioactivity was determined by measuring some radionuclides belonging to Th-232 and U-238 natural radioactive families, and of K-40 concentrations. Several types of soils from Southern Brazil; and soil samples, marine sediments, lichens, mosses and algae collected at King George and other nearby islands (South Shetland Archipelago, Antarctica) were analyzed. A gamma-ray spectrometer was used to measure radioactivity levels of the collected samples and its overall characteristics are analyzed in this work. (author)

Collection and preparation of samples for gamma spectrometry

International Nuclear Information System (INIS)

Pan Jingquan

1994-01-01

The paper presents the basic principles of sample collection and preparation: setting up unified sampling program, methods and procedures, sample packing, transportation and storage, determination of sample quantity, sample pretreatment and preparation of samples to be analysed, etc. for gamma spectrometry. And the paper also describes briefly the main methods and special issues of sampling and preparation for the same environmental and biological samples, such as, air, water, grass, soil and foods

Measurements of Plutonium and Americium in Soil Samples from Project 57 using the Suspended Soil Particle Sizing System (SSPSS)

International Nuclear Information System (INIS)

John L. Bowen; Rowena Gonzalez; David S. Shafer

2001-01-01

As part of the preliminary site characterization conducted for Project 57, soils samples were collected for separation into several size-fractions using the Suspended Soil Particle Sizing System (SSPSS). Soil samples were collected specifically for separation by the SSPSS at three general locations in the deposited Project 57 plume, the projected radioactivity of which ranged from 100 to 600 pCi/g. The primary purpose in focusing on samples with this level of activity is that it would represent anticipated residual soil contamination levels at the site after corrective actions are completed. Consequently, the results of the SSPSS analysis can contribute to dose calculation and corrective action-level determinations for future land-use scenarios at the site

Instrumental neutron activation analysis of soil sample

International Nuclear Information System (INIS)

Abdul Khalik Haji Wood.

1983-01-01

This paper describes the analysis of soil samples collected from 5 different location around Sungai Lui, Kajang, Selangor, Malaysia. These sample were taken at 22-24 cm from the top of the ground and were analysed using the techniques of Instrumental Neutron Activation Analysis (INAA). The analysis on soil sample taken above 22-24 cm level were done in order to determine if there is any variation in elemental contents at different sampling levels. The results indicate a wide variation in the contents of the samples. About 30 elements have been analysed. The major ones are Na, I, Cl, Mg, Al, K, Ti, Ca and Fe. Trace elements analysed were Ba, Sc, V, Cr, Mn, Ga, As, Zn, Br, Rb, Co, Hf, Zr, Th, U, Sb, Cs, Ce, Sm, Eu, Tb, Dy, Yb, Lu and La. (author)

An evaluation of soil sampling for 137Cs using various field-sampling volumes.

Science.gov (United States)

Nyhan, J W; White, G C; Schofield, T G; Trujillo, G

1983-05-01

The sediments from a liquid effluent receiving area at the Los Alamos National Laboratory and soils from an intensive study area in the fallout pathway of Trinity were sampled for 137Cs using 25-, 500-, 2500- and 12,500-cm3 field sampling volumes. A highly replicated sampling program was used to determine mean concentrations and inventories of 137Cs at each site, as well as estimates of spatial, aliquoting, and counting variance components of the radionuclide data. The sampling methods were also analyzed as a function of soil size fractions collected in each field sampling volume and of the total cost of the program for a given variation in the radionuclide survey results. Coefficients of variation (CV) of 137Cs inventory estimates ranged from 0.063 to 0.14 for Mortandad Canyon sediments, whereas CV values for Trinity soils were observed from 0.38 to 0.57. Spatial variance components of 137Cs concentration data were usually found to be larger than either the aliquoting or counting variance estimates and were inversely related to field sampling volume at the Trinity intensive site. Subsequent optimization studies of the sampling schemes demonstrated that each aliquot should be counted once, and that only 2-4 aliquots out of as many as 30 collected need be assayed for 137Cs. The optimization studies showed that as sample costs increased to 45 man-hours of labor per sample, the variance of the mean 137Cs concentration decreased dramatically, but decreased very little with additional labor.

Genotyping of Toxoplasma Gondii Isolates from Soil Samples in Tehran, Iran

Directory of Open Access Journals (Sweden)

M Tavalla

2013-06-01

Full Text Available Background: The protozoan parasite Toxoplasma gondii can infect any warm blooded nucleated cells. One of the ways for human infection is ingestion of oocysts directly from soil or via infected fruits or vegetables. To survey the potential role of T. gondii oocyst in soil samples, the present study was conducted in Tehran City, Iran.Methods: A total of 150 soil samples were collected around rubbish dumps, children's play ground, parks and public places. Oocysts recovery was performed by sodium nitrate flotation method on soil samples. For molecular detection, PCR reaction targeting B1 gene was performed and then, the posi­tive results were confirmed using repetitive 529 bp DNA fragment in other PCR reaction. Finally, the positive samples were genotyped at the SAG2 locus.Results: Toxoplasma DNA was found in 13 soil samples. After genotyping and RFLP analysis in SAG2 locus, nine positive samples were revealed type III, one positive sample was type I whereas three samples revealed mixed infection (type, I & III.Conclusion: The predominant genotype in Tehran soil samples is type III.

Optimization of sampling for the determination of the mean Radium-226 concentration in surface soil

International Nuclear Information System (INIS)

Williams, L.R.; Leggett, R.W.; Espegren, M.L.; Little, C.A.

1987-08-01

This report describes a field experiment that identifies an optimal method for determination of compliance with the US Environmental Protection Agency's Ra-226 guidelines for soil. The primary goals were to establish practical levels of accuracy and precision in estimating the mean Ra-226 concentration of surface soil in a small contaminated region; to obtain empirical information on composite vs. individual soil sampling and on random vs. uniformly spaced sampling; and to examine the practicality of using gamma measurements in predicting the average surface radium concentration and in estimating the number of soil samples required to obtain a given level of accuracy and precision. Numerous soil samples were collected on each six sites known to be contaminated with uranium mill tailings. Three types of samples were collected on each site: 10-composite samples, 20-composite samples, and individual or post hole samples; 10-composite sampling is the method of choice because it yields a given level of accuracy and precision for the least cost. Gamma measurements can be used to reduce surface soil sampling on some sites. 2 refs., 5 figs., 7 tabs

Collecting Ground Samples for Balloon-Borne Instruments

Science.gov (United States)

Jones, Jack; Zimmerman, Wayne; Wu, Jiunn Jenq

2009-01-01

A proposed system in a gondola containing scientific instruments suspended by a balloon over the surface of the Saturn moon Titan would quickly acquire samples of rock or ice from the ground below. Prototypes of a sample-collecting device that would be a major part of the system have been tested under cryogenic and non-cryogenic conditions on Earth. Systems like this one could also be used in non-cryogenic environments on Earth to collect samples of rock, soil, ice, mud, or other ground material from such inaccessible or hazardous locations as sites of suspected chemical spills or biological contamination. The sample-collecting device would be a harpoonlike device that would be connected to the balloon-borne gondola by a tether long enough to reach the ground. The device would be dropped from the gondola to acquire a sample, then would be reeled back up to the gondola, where the sample would be analyzed by the onboard instruments. Each prototype of the sample-collecting device has a sharp front (lower) end, a hollow core for retaining a sample, a spring for holding the sample in the hollow core, and a rear (upper) annular cavity for retaining liquid sample material. Aerodynamic fins at the rear help to keep the front end pointed downward. In tests, these prototype devices were dropped from various heights and used to gather samples of dry sand, moist sand, cryogenic water ice, and warmer water ice.

Soil Characterization by Large Scale Sampling of Soil Mixed with Buried Construction Debris at a Former Uranium Fuel Fabrication Facility

International Nuclear Information System (INIS)

Nardi, A.J.; Lamantia, L.

2009-01-01

Recent soil excavation activities on a site identified the presence of buried uranium contaminated building construction debris. The site previously was the location of a low enriched uranium fuel fabrication facility. This resulted in the collection of excavated materials from the two locations where contaminated subsurface debris was identified. The excavated material was temporarily stored in two piles on the site until a determination could be made as to the appropriate disposition of the material. Characterization of the excavated material was undertaken in a manner that involved the collection of large scale samples of the excavated material in 1 cubic meter Super Sacks. Twenty bags were filled with excavated material that consisted of the mixture of both the construction debris and the associated soil. In order to obtain information on the level of activity associated with the construction debris, ten additional bags were filled with construction debris that had been separated, to the extent possible, from the associated soil. Radiological surveys were conducted of the resulting bags of collected materials and the soil associated with the waste mixture. The 30 large samples, collected as bags, were counted using an In-Situ Object Counting System (ISOCS) unit to determine the average concentration of U-235 present in each bag. The soil fraction was sampled by the collection of 40 samples of soil for analysis in an on-site laboratory. A fraction of these samples were also sent to an off-site laboratory for additional analysis. This project provided the necessary soil characterization information to allow consideration of alternate options for disposition of the material. The identified contaminant was verified to be low enriched uranium. Concentrations of uranium in the waste were found to be lower than the calculated site specific derived concentration guideline levels (DCGLs) but higher than the NRC's screening values. The methods and results are presented

Historical review of long-term soil sampling for environmental surveillance at the Hanford Site and vicinity

Energy Technology Data Exchange (ETDEWEB)

Price, K.R.; Rickard, W.H.

1997-08-01

Soil samples have been collected routinely from the environs of the Hanford Site and analyzed since 1971. Correct interpretation of results depends on samples being collected from the same locations, the locations remaining relatively undisturbed, and collection and analytical procedures remaining the same or being equivalent. Historical files, documents, and annual environmental reports were reviewed to evaluate these factors. It was determined that 20 soil sampling locations, 11 onsite and 9 offsite, were established between 1971 and 1977 and represent long-term sampling locations. Sample collection and analytical procedures have remained essentially the same since 1971. The physical ecological attributes of each long-term soil sampling location were evaluated. During the review of historical records, a few results for 1970, 1971, and 1972 were noted as previously unreported in annual or special reports. These results are included in Appendix A. To complete the record, results previously reported in annual environmental reports are given in Appendix B. Global Positioning System (GPS) reading for 20 long-term soil sampling locations are provided in Appendix C.

Historical review of long-term soil sampling for environmental surveillance at the Hanford Site and vicinity

International Nuclear Information System (INIS)

Price, K.R.; Rickard, W.H.

1997-08-01

Soil samples have been collected routinely from the environs of the Hanford Site and analyzed since 1971. Correct interpretation of results depends on samples being collected from the same locations, the locations remaining relatively undisturbed, and collection and analytical procedures remaining the same or being equivalent. Historical files, documents, and annual environmental reports were reviewed to evaluate these factors. It was determined that 20 soil sampling locations, 11 onsite and 9 offsite, were established between 1971 and 1977 and represent long-term sampling locations. Sample collection and analytical procedures have remained essentially the same since 1971. The physical ecological attributes of each long-term soil sampling location were evaluated. During the review of historical records, a few results for 1970, 1971, and 1972 were noted as previously unreported in annual or special reports. These results are included in Appendix A. To complete the record, results previously reported in annual environmental reports are given in Appendix B. Global Positioning System (GPS) reading for 20 long-term soil sampling locations are provided in Appendix C

Stability of mercury concentration measurements in archived soil and peat samples

Science.gov (United States)

Navrátil, Tomáš; Burns, Douglas; Nováková, Tereza; Kaňa, Jiří; Rohovec, Jan; Roll, Michal; Ettler, Vojtěch

2018-01-01

Archived soil samples can provide important information on the history of environmental contamination and by comparison with recently collected samples, temporal trends can be inferred. Little previous work has addressed whether mercury (Hg) concentrations in soil samples are stable with long-term storage under standard laboratory conditions. In this study, we have re-analyzed using cold vapor atomic adsorption spectroscopy a set of archived soil samples that ranged from relatively pristine mountainous sites to a polluted site near a non-ferrous metal smelter with a wide range of Hg concentrations (6 - 6485 µg kg-1). Samples included organic and mineral soils and peats with a carbon content that ranged from 0.2 to 47.7%. Soil samples were stored in polyethylene bags or bottles and held in laboratory rooms where temperature was not kept to a constant value. Mercury concentrations in four subsets of samples were originally measured in 2000, 2005, 2006 and 2007, and re-analyzed in 2017, i.e. after 17, 12, 11 and 10 years of storage. Statistical analyses of either separated or lumped data yielded no significant differences between the original and current Hg concentrations. Based on these analyses, we show that archived soil and peat samples can be used to evaluate historical soil mercury contamination.

Area G perimeter surface-soil and single-stage water sampling. Environmental surveillance for fiscal year 95. Progress report

International Nuclear Information System (INIS)

Childs, M.; Conrad, R.

1997-09-01

ESH-19 personnel collected soil and single-stage water samples around the perimeter of Area G at Los Alamos National Laboratory (LANL) during FY 95 to characterize possible radionuclide movement out of Area G through surface water and entrained sediment runoff. Soil samples were analyzed for tritium, total uranium, isotopic plutonium, americium-241, and cesium-137. The single-stage water samples were analyzed for tritium and plutonium isotopes. All radiochemical data was compared with analogous samples collected during FY 93 and 94 and reported in LA-12986 and LA-13165-PR. Six surface soils were also submitted for metal analyses. These data were included with similar data generated for soil samples collected during FY 94 and compared with metals in background samples collected at the Area G expansion area

Determination of gold of No. 501 uranium deposits and soil samples by cold leaching gold in dilute aqua regia and collection on activated charcoal

International Nuclear Information System (INIS)

Shen Maogen; Yao Liying.

1989-01-01

The gold determination method is described by cold leaching gold in dilute aqua regia and collection on activated charcoal and presents the results obtained in determining gold of uranium deposits and soil samples

Soil sampling in emergency situations

International Nuclear Information System (INIS)

Carvalho, Zenildo Lara de; Ramos Junior, Anthenor Costa

1997-01-01

The soil sampling methods used in Goiania's accident (1987) by the environmental team of Brazilian Nuclear Energy Commission (CNEN) are described. The development of this method of soil sampling to a emergency sampling method used in a Nuclear Emergency Exercise in Angra dos Reis Reactor Site (1991) is presented. A new method for soil sampling based on a Chernobyl environmental monitoring experience (1995) is suggested. (author)

Environmental radiation levels in soil and sediment samples collected from floating water from a land runway resulting from heavy rains in the Jeddah region, KSA

International Nuclear Information System (INIS)

Mohery, M.; Baz, Shadiah; Kelany, Adel M.; Abdallah, A.M.

2014-01-01

The natural radiation levels in soil and sediment samples collected from floating water from a land runway resulting from heavy rains in the Jeddah region as well as the activity in the population of its surrounding environments were studied. In the regions surrounding Jeddah, the movements of floating water may increase the concentration of radioactivity due to the movement of soil due to heavy rains. In addition, the technological development of industry, agriculture and other sources around the Jeddah region has increased environmental pollution, resulting in noticeable concentrations of radioactivity. The measured activity concentrations of 214 Pb, 214 Bi, 228 Ac, 208 Tl, 40 K, 226 Ra and 228 Ra in the studied area suggest that they are within the world average for soils and sediments, except those for water sample no. 4; the concentration in this sample was five times higher than the world average concentration (this water is not consumable). Herein, the radioactivity concentrations that were obtained from the analysis of soil and sediment samples that were collected from the investigated area are discussed. Additionally, the absorbed dose rate (D), radium equivalent activity (Ra eq ), external hazard index (H ex ), annual gonadal dose equivalent (AGDE) and annual effective dose equivalent (AEDE) were evaluated. For the soil and sediment samples, the average radioactivity concentrations were determined for each site and are expressed in Becquerels per kilogram (Bq/kg) of dry weight, while for the measurement of both the 226 Ra and 228 Ra isotopes in the water samples, the activity concentration is expressed in picoCuries per liter (pCi/l). The obtained results were compared with other measurements from different countries. The movement of floating water around the Jeddah region increases the concentration of radioactivity due to the movement of soils with heavy rains. - Highlights: • The natural radiation levels in soil and sediment samples from floating

Gamma spectroscopy analysis of archived Marshall Island soil samples

International Nuclear Information System (INIS)

Herman, S.; Hoffman, K.; Lavelle, K.; Trauth, A.; Glover, S.E.; Connick, W.; Spitz, H.; LaMont, S.P.; Hamilton, T.

2016-01-01

Four samples of archival Marshall Islands soil were subjected to non-destructive, broad energy (17 keV-2.61 MeV) gamma-ray spectrometry analysis using a series of different high-resolution germanium detectors. These archival samples were collected in 1967 from different locations on Bikini Atoll and were contaminated with a range of fission and activation products, and other nuclear material from multiple weapons tests. Unlike samples collected recently, these samples have been stored in sealed containers and have been unaffected by approximately 50 years of weathering. Initial results show that the samples contained measurable but proportionally different concentrations of plutonium, 241 Am, and 137 Cs, and 60 Co. (author)

Elemental contents in soil samples in Wad Hamid, River Nile State

International Nuclear Information System (INIS)

Mohammed, Khansaa Elawad Elhag

2016-03-01

In the present study a total of 30 samples were collected from Wad Hamid River Nile State. Sampling area of (two feddan) of agricultural soil. The sampling area was divided in two locations (fertile and non fertile soil). The samples were analyzed for their content of 13 elements (K, Ca, Ti, Mn, Fe, Cu, Zn, Pb, Rb, Sr, Y, Zr, and Np). 10 samples from location 1 (non-fertile soil) and 20 samples from location 2 (fertile soil). X-ray fluorescence (X RF) Spectrometer (system used based on 1"0"9"Cd excitation 1"0"9"Cd source which has an average energy of 22.6 kev and able to excite the elements from Z = 13 to 92 using K and L lines) used to identify the elemental concentration in soil samples. The reliability of X RF technique as multi elements detecting method for measuring elements concentration in soil sample , (IAEA-SOIL-7) standard reference material was used. Measured values found in agreement with the certified values. The average elemental concentration of K,Ca, Ti, Fe, Cu, Zn, Pb, Sr, Y, Zr, and Np in location 1 were 878, 29690, 13400, 983, 70380, 10.07, 19.07, 40.92,261.4, 23.59,294.8, 47.82, while the average elemental concentration in location 2 were 9848, 27780, 13076,13076,989, 68135, 9.6, 96.3 19.86, 43.7, 225.5, 22.49, 284.75, 46.15, respectively. comparison between the average elemental concentration in fertile soil and non-fertile was done correlations between element were performed Cluster analyses of element in soil samples were obtained comparison between this study and data from literature were done. The elemental concentration in location 1 (non- fertile soil) are higher than location 2 ( fertile soil) because the plant absorbed fertilizer of soil and transfer most elements in soil to plant. (Author)

Soil sampling for environmental contaminants

International Nuclear Information System (INIS)

2004-10-01

The Consultants Meeting on Sampling Strategies, Sampling and Storage of Soil for Environmental Monitoring of Contaminants was organized by the International Atomic Energy Agency to evaluate methods for soil sampling in radionuclide monitoring and heavy metal surveys for identification of punctual contamination (hot particles) in large area surveys and screening experiments. A group of experts was invited by the IAEA to discuss and recommend methods for representative soil sampling for different kinds of environmental issues. The ultimate sinks for all kinds of contaminants dispersed within the natural environment through human activities are sediment and soil. Soil is a particularly difficult matrix for environmental pollution studies as it is generally composed of a multitude of geological and biological materials resulting from weathering and degradation, including particles of different sizes with varying surface and chemical properties. There are so many different soil types categorized according to their content of biological matter, from sandy soils to loam and peat soils, which make analytical characterization even more complicated. Soil sampling for environmental monitoring of pollutants, therefore, is still a matter of debate in the community of soil, environmental and analytical sciences. The scope of the consultants meeting included evaluating existing techniques with regard to their practicability, reliability and applicability to different purposes, developing strategies of representative soil sampling for cases not yet considered by current techniques and recommending validated techniques applicable to laboratories in developing Member States. This TECDOC includes a critical survey of existing approaches and their feasibility to be applied in developing countries. The report is valuable for radioanalytical laboratories in Member States. It would assist them in quality control and accreditation process

Residual neutron-induced radionuclides in a soil sample collected in the vicinity of the criticality accident site in Tokai-mura, Japan: A Progress Report

International Nuclear Information System (INIS)

Nakanishi, Takashi; Hosotani, Risa; Komura, Kazuhisa; Muroyama, Toshiharu; Kofuji, Hisaki; Murata, Yoshimasa; Kimura, Shinzo; Kumar Sahoo, Sarata; Yonehara, Hidenori; Watanabe, Yoshito; Ban-nai, Tada-aki

2000-01-01

Residual neutron-induced radionuclides were measured in a soil sample collected in the vicinity of the location where a criticality accident occurred (in Tokai-mura, from 30 September to 1 October, 1999). Concentrations of 24 Na, 140 La, 122 Sb, 59 Fe, 124 Sb, 46 Sc, 65 Zn, 134 Cs and 60 Co in the soil sample were determined by γ-ray spectrometry, and neutron activation analysis was carried out for selected target elements in the sample. Tentative estimates of the apparent thermal and epithermal neutron fluences which reached the sample were obtained through combined analyses of 59 Fe/ 58 Fe, 124 Sb/ 123 Sb, 46 Sc/ 45 Sc, 65 Zn/ 64 Zn, 134 Cs/ 133 Cs and 60 Co/ 59 Co

Sampling Design of Soil Physical Properties in a Conilon Coffee Field

Directory of Open Access Journals (Sweden)

Eduardo Oliveira de Jesus Santos

Full Text Available ABSTRACT Establishing the number of samples required to determine values of soil physical properties ultimately results in optimization of labor and allows better representation of such attributes. The objective of this study was to analyze the spatial variability of soil physical properties in a Conilon coffee field and propose a soil sampling method better attuned to conditions of the management system. The experiment was performed in a Conilon coffee field in Espírito Santo state, Brazil, under a 3.0 × 2.0 × 1.0 m (4,000 plants ha-1 double spacing design. An irregular grid, with dimensions of 107 × 95.7 m and 65 sampling points, was set up. Soil samples were collected from the 0.00-0.20 m depth from each sampling point. Data were analyzed under descriptive statistical and geostatistical methods. Using statistical parameters, the adequate number of samples for analyzing the attributes under study was established, which ranged from 1 to 11 sampling points. With the exception of particle density, all soil physical properties showed a spatial dependence structure best fitted to the spherical model. Establishment of the number of samples and spatial variability for the physical properties of soils may be useful in developing sampling strategies that minimize costs for farmers within a tolerable and predictable level of error.

Measurement of technetium-99 in Marshall Islands soil samples by ICP-MS

Science.gov (United States)

Tagami; Uchida; Hamilton; Robison

2000-07-01

Extraction techniques for recovery of technetium-99 (99Tc) for Inductively Coupled Plasma Mass Spectrometry (ICP-MS) measurements were evaluated using soil samples collected from the Marshall Islands. The results of three different extraction techniques were compared: (MI) acid leaching of Tc from ashed soil; (M2) acid leaching of Tc from raw dry soil; and (M3) Tc volatilization from ashed soil using a combustion apparatus. Total Tc recoveries varied considerably between the extraction techniques but each method yielded similar analytical results for 99Tc. Applications of these extraction techniques to a series of environmental samples and ICP-MS measurements have yielded first data on the 99Tc content of Marshall Islands soil samples contaminated with close-in radioactive fallout from nuclear weapons testing. The 99Tc activity concentration in the soil samples ranged between 0.1 and 1.1 mBq g(-1) dry weight (dw). The limit of detection for 99Tc by ICP-MS was 0.17 mBq per sample or 0.014 mBq g(-1) dw under standard operating conditions.

Measurement of technetium-99 in Marshall Islands soil samples by ICP-MS

International Nuclear Information System (INIS)

Tagami, K.; Uchida, S.; Hamilton, T.; Robison, W.

2000-01-01

Extraction techniques for recovery of technetium-99 ( 99 Tc) for Inductively Coupled Plasma Mass Spectrometry (ICP-MS) measurements were evaluated using soil samples collected from the Marshall Islands. The results of three different extraction techniques were compared: (M1) acid leaching of Tc from ashed soil; (M2) acid leaching of Tc from raw dry soil; and (M3) Tc volatilization from ashed soil using a combustion apparatus. Total Tc recoveries varied considerably between the extraction techniques but each method yielded similar analytical results for 99 Tc. Applications of these extraction techniques to a series of environmental samples and ICP-MS measurements have yielded first data on the 99 Tc content of Marshall Islands soil samples contaminated with close-in radioactive fallout from nuclear weapons testing. The 99 Tc activity concentration in the soil samples ranged between 0.1 and 1.1 mBq g -1 dry weight (dw). The limit of detection for 99 Tc by ICP-MS was 0.17 mBq per sample or 0.014 mBq g -1 dw under standard operating conditions

Sampling and analysis of soil from the old F-Area effluent ditch and its surrounding wetlands

International Nuclear Information System (INIS)

Dixon, K.L.

1994-06-01

Four surface soil samples were collected from the wetlands at the old F-Area effluent ditch. All samples were collected near shallow well point locations except FHB012, which was collected from the effluent ditch stream sediment. Samples were analyzed for metals, Target Compound List volatile organic compounds, and gross radiological indicators. Barium, beryllium, and zinc were detected in all four samples and antimony was detected in three of four samples. These metals occur naturally in the wetland soils at the SRS. Comparisons of metals concentrations were male to concentration ranges taken from background wetland soil samples. These comparison, showed that barium and beryllium concentrations were within expected ranges while zinc and antimony concentrations were elevated above expected concentration ranges. Volatile organic compounds were detected in all four samples. Detected compounds included acetone, 2-butanone, chloromethane, cis-1,2-dichloroethene, and toluene. The only radionuclide detected in a significant quantities was tritium which was detected in all four samples

Biopolymers for sample collection, protection, and preservation.

Science.gov (United States)

Sorokulova, Iryna; Olsen, Eric; Vodyanoy, Vitaly

2015-07-01

One of the principal challenges in the collection of biological samples from air, water, and soil matrices is that the target agents are not stable enough to be transferred from the collection point to the laboratory of choice without experiencing significant degradation and loss of viability. At present, there is no method to transport biological samples over considerable distances safely, efficiently, and cost-effectively without the use of ice or refrigeration. Current techniques of protection and preservation of biological materials have serious drawbacks. Many known techniques of preservation cause structural damages, so that biological materials lose their structural integrity and viability. We review applications of a novel bacterial preservation process, which is nontoxic and water soluble and allows for the storage of samples without refrigeration. The method is capable of protecting the biological sample from the effects of environment for extended periods of time and then allows for the easy release of these collected biological materials from the protective medium without structural or DNA damage. Strategies for sample collection, preservation, and shipment of bacterial, viral samples are described. The water-soluble polymer is used to immobilize the biological material by replacing the water molecules within the sample with molecules of the biopolymer. The cured polymer results in a solid protective film that is stable to many organic solvents, but quickly removed by the application of the water-based solution. The process of immobilization does not require the use of any additives, accelerators, or plastifiers and does not involve high temperature or radiation to promote polymerization.

An Open-source Low-cost Portable Apparatus for Soil Fauna Sampling

Science.gov (United States)

Daliakopoulos, Ioannis; Wagner, Karl; Grillakis, Manolis; Apostolakis, Antonios; Tsanis, Ioannis

2016-04-01

A low-cost apparatus for the extraction of living soil animals from soil or litter samples is presented. The main unit consists of a modular bank system with three horizontal shelves designed to accommodate lamps and soil samples over funnel and jar systems for animal collection, thus serving as a practical and standardized modification of the well-documented Berlese-Tullgren funnel. Shelves are vertically adjustable, sliding on 5 mm threaded rods and securing with wing nuts for easy assembly/disassembly and stability. Shelf material is 4 mm plywood (or similar), laser-cut (or similar) to accommodate lamp sockets, tubes and funnels at respective levels. Soil samples are inserted in 10 cm tubes from standard Ø50 mm PVC piping that can also function as direct collection corers for softer soils. Tubes are fitted in the tube bank shelf, each directly under a 25 W reflector lamp and over a funnel and jar system. Lamps are located 25 mm over the tubes' top creating a relatively constant 10 oC temperature gradient that drives soil animals away from heat and light, and towards the bottom end of the tube which is fitted with a suitable fabric mesh. Standard 106 ml panelled jars, filled with a safe-to-handle preservative (e.g. propylene glycol) to the lower end of the funnel fitted in them, trap and preserve soil organisms until identification. The apparatus offers flat-pack portability and scalability using low-cost standard material. Design specifications and Drawing eXchange Format (dxf) files for apparatus reproduction are provided.

Procedures for sampling radium-contaminated soils

International Nuclear Information System (INIS)

Fleischhauer, H.L.

1985-10-01

Two procedures for sampling the surface layer (0 to 15 centimeters) of radium-contaminated soil are recommended for use in remedial action projects. Both procedures adhere to the philosophy that soil samples should have constant geometry and constant volume in order to ensure uniformity. In the first procedure, a ''cookie cutter'' fashioned from pipe or steel plate, is driven to the desired depth by means of a slide hammer, and the sample extracted as a core or plug. The second procedure requires use of a template to outline the sampling area, from which the sample is obtained using a trowel or spoon. Sampling to the desired depth must then be performed incrementally. Selection of one procedure over the other is governed primarily by soil conditions, the cookie cutter being effective in nongravelly soils, and the template procedure appropriate for use in both gravelly and nongravelly soils. In any event, a minimum sample volume of 1000 cubic centimeters is recommended. The step-by-step procedures are accompanied by a description of the minimum requirements for sample documentation. Transport of the soil samples from the field is then addressed in a discussion of the federal regulations for shipping radioactive materials. Interpretation of those regulations, particularly in light of their application to remedial action soil-sampling programs, is provided in the form of guidance and suggested procedures. Due to the complex nature of the regulations, however, there is no guarantee that our interpretations of them are complete or entirely accurate. Preparation of soil samples for radium-226 analysis by means of gamma-ray spectroscopy is described

Determination of the activity concentration levels of the artificial radionuclide137Cs in soil samples collected from Qatar using high-resolution gamma-ray spectrometry

Science.gov (United States)

Al-Sulaiti, Huda; Nasir, Tabassum; Al Mugren, K. S.; Alkhomashi, N.; Al-Dahan, N.; Al-Dosari, M.; Bradley, D. A.; Bukhari, S.; Regan, P. H.; Santawamaitre, T.; Malain, D.; Habib, A.; Al-Dosari, Hanan; Daar, Eman

2016-09-01

The goal of this study was to establish the first baseline measurements for radioactivity concentration of the artificial radionuclide 137Cs in soil samples collected from the Qatarian peninsula. The work focused on the determination of the activity concentrations levels of man-made radiation in 129 soil samples collected across the landscape of the State of Qatar. All the samples were collected before the most recent accident in Japan, “the 2011 Fukushima Dai-ichi nuclear power plant accident”. The activity concentrations have been measured via high-resolution gamma-ray spectrometry using a hyper-pure germanium detector situated in a low-background environment with a copper inner-plated passive lead shield. A radiological map showing the activity concentrations of 137Cs is presented in this work. The concentration wasfound to range from 0.21 to 15.41 Bq/kg. The highest activity concentration of 137Cs was observed in sample no. 26 in North of Qatar. The mean value was found to be around 2.15 ± 0.27 Bq/kg. These values lie within the expected range relative to the countries in the region. It is expected that this contamination is mainly due to the Chernobyl accident on 26 April 1986, but this conclusion cannot be confirmed because of the lack of data before this accident.

Trace element analysis of soil type collected from the Manjung and central Perak

Energy Technology Data Exchange (ETDEWEB)

Azman, Muhammad Azfar, E-mail: m-azfar@nuclearmalaysia.gov.my; Hamzah, Suhaimi; Rahman, Shamsiah Abdul; Elias, Md Suhaimi; Abdullah, Nazaratul Ashifa; Hashim, Azian; Shukor, Shakirah Abd; Kamaruddin, Ahmad Hasnulhadi Che [Blok 18, Makmal Analisis Kimia (Aca/Bas), Agensi Nuklear Malaysia, 43000 Kajang, Selangor (Malaysia)

2015-04-29

Trace elements in soils primarily originated from their parent materials. Parents’ material is the underlying geological material that has been undergone different types of chemical weathering and leaching processes. Soil trace elements concentrations may be increases as a result of continuous input from various human activities, including power generation, agriculture, mining and manufacturing. This paper describes the Neutron Activation Analysis (NAA) method used for the determination of trace elements concentrations in part per million (ppm) present in the terrestrial environment soil in Perak. The data may indicate any contamination of trace elements contributed from human activities in the area. The enrichment factors were used to check if there any contamination due to the human activities (power plants, agricultural, mining, etc.) otherwise the values would serve as a baseline data for future study. The samples were collected from 27 locations of different soil series in the area at two different depths: the top soil (0-15cm) and the sub soil (15-30cm). The collected soil samples were air dried at 60°C and passed through 2 µm sieve. Instrumental Neutron Activation Analysis (NAA) has been used for the determination of trace elements. Samples were activated in the Nuclear Malaysia TRIGA Mark II reactor followed by gamma spectrometric analysis. By activating the stable elements in the samples, the elements can be determined from the intensities of gamma energies emitted by the respected radionuclides.

Prompt Gamma Ray Analysis of Soil Samples

Energy Technology Data Exchange (ETDEWEB)

Naqvi, A.A.; Khiari, F.Z.; Haseeb, S.M.A.; Hussein, Tanvir; Khateeb-ur-Rehman [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia); Isab, A.H. [Department of Chemistry, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia)

2015-07-01

Neutron moderation effects were measured in bulk soil samples through prompt gamma ray measurements from water and benzene contaminated soil samples using 14 MeV neutron inelastic scattering. The prompt gamma rays were measured using a cylindrical 76 mm x 76 mm (diameter x height) LaBr{sub 3}:Ce detector. Since neutron moderation effects strongly depend upon hydrogen concentration of the sample, for comparison purposes, moderation effects were studied from samples containing different hydrogen concentrations. The soil samples with different hydrogen concentration were prepared by mixing soil with water as well as benzene in different weight proportions. Then, the effects of increasing water and benzene concentrations on the yields of hydrogen, carbon and silicon prompt gamma rays were measured. Moderation effects are more pronounced in soil samples mixed with water as compared to those from soil samples mixed with benzene. This is due to the fact that benzene contaminated soil samples have about 30% less hydrogen concentration by weight than the water contaminated soil samples. Results of the study will be presented. (authors)

14CO2 analysis of soil gas: Evaluation of sample size limits and sampling devices

Science.gov (United States)

Wotte, Anja; Wischhöfer, Philipp; Wacker, Lukas; Rethemeyer, Janet

2017-12-01

Radiocarbon (14C) analysis of CO2 respired from soils or sediments is a valuable tool to identify different carbon sources. The collection and processing of the CO2, however, is challenging and prone to contamination. We thus continuously improve our handling procedures and present a refined method for the collection of even small amounts of CO2 in molecular sieve cartridges (MSCs) for accelerator mass spectrometry 14C analysis. Using a modified vacuum rig and an improved desorption procedure, we were able to increase the CO2 recovery from the MSC (95%) as well as the sample throughput compared to our previous study. By processing series of different sample size, we show that our MSCs can be used for CO2 samples of as small as 50 μg C. The contamination by exogenous carbon determined in these laboratory tests, was less than 2.0 μg C from fossil and less than 3.0 μg C from modern sources. Additionally, we tested two sampling devices for the collection of CO2 samples released from soils or sediments, including a respiration chamber and a depth sampler, which are connected to the MSC. We obtained a very promising, low process blank for the entire CO2 sampling and purification procedure of ∼0.004 F14C (equal to 44,000 yrs BP) and ∼0.003 F14C (equal to 47,000 yrs BP). In contrast to previous studies, we observed no isotopic fractionation towards lighter δ13C values during the passive sampling with the depth samplers.

Measurement of technetium-99 in Marshall Islands soil samples by ICP-MS

Energy Technology Data Exchange (ETDEWEB)

Tagami, K. E-mail: k_tagami@nirs.go.jp; Uchida, S.; Hamilton, T.; Robison, W

2000-07-15

Extraction techniques for recovery of technetium-99 ({sup 99}Tc) for Inductively Coupled Plasma Mass Spectrometry (ICP-MS) measurements were evaluated using soil samples collected from the Marshall Islands. The results of three different extraction techniques were compared: (M1) acid leaching of Tc from ashed soil; (M2) acid leaching of Tc from raw dry soil; and (M3) Tc volatilization from ashed soil using a combustion apparatus. Total Tc recoveries varied considerably between the extraction techniques but each method yielded similar analytical results for {sup 99}Tc. Applications of these extraction techniques to a series of environmental samples and ICP-MS measurements have yielded first data on the {sup 99}Tc content of Marshall Islands soil samples contaminated with close-in radioactive fallout from nuclear weapons testing. The {sup 99}Tc activity concentration in the soil samples ranged between 0.1 and 1.1 mBq g{sup -1} dry weight (dw). The limit of detection for {sup 99}Tc by ICP-MS was 0.17 mBq per sample or 0.014 mBq g{sup -1} dw under standard operating conditions.

Isolation of Lead Resistant Bacteria from Lead Contaminated Soil Samples Collected from Sundar Industrial Estate and their Potential Use in Bioremediation

International Nuclear Information System (INIS)

Saleem, F.; Adalat, R.; Munir, N.; Aftab, F.

2015-01-01

Industrial waste water pollution is one of the most controversial problem especially in countries like Pakistan. Human activities and the release of industrial waste have resulted the accumulation of metals in the environment. Noxious chemicals like heavy metals include cadmium, lead, chromium, copper, nickel, etc. that pollute the soils, ground water, sediments and surface waters re present in soluble form. Biosorpotion is a form of bioremediation by which metal ions are adsorbed from polluted site by microorganisms. Samples collected from industrial area were analyzed for lead contamination by Flame Atomic Spectrophotometer. Soil samples of Sundar Industrial Estate were highly resistant to different concentrations (300ppm, 800ppm, and 1600ppm) of Pb+2 whereas, the sample PbFa-458 showed maximum (127.9819mg/L) absorption of Pb+2, so can be used for environmental cleanup. From 24 selected lead resistant strains PbFa-136, PbFa-287, PbFa-960 showed resistance to multimetals, multidrug and high lead concentrations i.e 1800ppm, 2000ppm. Lead resistant strains were predicted as Klebsiella or Eenterobacter, Bacillus, Shigella, Salmonella and Enteroccocus. (author)

Soil sampling

International Nuclear Information System (INIS)

Fortunati, G.U.; Banfi, C.; Pasturenzi, M.

1994-01-01

This study attempts to survey the problems associated with techniques and strategies of soil sampling. Keeping in mind the well defined objectives of a sampling campaign, the aim was to highlight the most important aspect of representativeness of samples as a function of the available resources. Particular emphasis was given to the techniques and particularly to a description of the many types of samplers which are in use. The procedures and techniques employed during the investigations following the Seveso accident are described. (orig.)

Mobility of arsenic, cadmium and zinc in a multi-element contaminated soil profile assessed by in-situ soil pore water sampling, column leaching and sequential extraction

International Nuclear Information System (INIS)

Beesley, Luke; Moreno-Jimenez, Eduardo; Clemente, Rafael; Lepp, Nicholas; Dickinson, Nicholas

2010-01-01

Three methods for predicting element mobility in soils have been applied to an iron-rich soil, contaminated with arsenic, cadmium and zinc. Soils were collected from 0 to 30 cm, 30 to 70 cm and 70 to 100 cm depths in the field and soil pore water was collected at different depths from an adjacent 100 cm deep trench. Sequential extraction and a column leaching test in the laboratory were compared to element concentrations in pore water sampled directly from the field. Arsenic showed low extractability, low leachability and occurred at low concentrations in pore water samples. Cadmium and zinc were more labile and present in higher concentrations in pore water, increasing with soil depth. Pore water sampling gave the best indication of short term element mobility when field conditions were taken into account, but further extraction and leaching procedures produced a fuller picture of element dynamics, revealing highly labile Cd deep in the soil profile. - Mobility of arsenic, cadmium and zinc in a polluted soil can be realistically interpreted by in-situ soil pore water sampling.

Isolation of antimicrobial producing Actinobacteria from soil samples.

Science.gov (United States)

Elbendary, Afaf Ahmed; Hessain, Ashgan Mohamed; El-Hariri, Mahmoud Darderi; Seida, Ahmed Adel; Moussa, Ihab Mohamed; Mubarak, Ayman Salem; Kabli, Saleh A; Hemeg, Hassan A; El Jakee, Jakeen Kamal

2018-01-01

Emergence of multidrug resistant bacteria has made the search for novel bioactive compounds from natural and unexplored habitats a necessity. Actinobacteria have important bioactive substances. The present study investigated antimicrobial activity of Actinobacteria isolated from soil samples of Egypt. One hundred samples were collected from agricultural farming soil of different governorates. Twelve isolates have produced activity against the tested microorganisms ( S. aureus , Bacillus cereus , E. coli , K. pneumoniae , P. aeruginosa , S. Typhi, C. albicans , A. niger and A. flavus ). By VITEK 2 system version: 07.01 the 12 isolates were identified as Kocuria kristinae , Kocuria rosea , Streptomyces griseus , Streptomyces flaveolus and Actinobacteria . Using ethyl acetate extraction method the isolates culture's supernatants were tested by diffusion method against indicator microorganisms. These results indicate that Actinobacteria isolated from Egypt farms could be sources of antimicrobial bioactive substances.

Study on natural radioactive elements in soil and rock samples around Mandya district, India

International Nuclear Information System (INIS)

Shivakumara, B.C.; Paramesh, L.; Shashikumar, T.S.; Chandrashekara, M.S.

2012-01-01

The soil is a complex mixture of different compounds and rocks. In the natural environment, it is an important source of exposure to radiation due to naturally occurring, gamma emitting radionuclides which include 226 Ra, 232 Th and 40 K present in the soil. The study of distribution of these radionuclides in soil and rock is of great importance for radiation protection and measurements. The activity concentrations of 226 Ra, 232 Th, and 40 K in soil and rock samples collected in Mandya District, Karnataka state, India have been measured by gamma ray spectrometry. The average activity concentrations of 226 Ra, 232 Th, and 40 K (Bq/kg) are found to be 40.2, 62.3, and 317.5 Bq/kg, respectively, in soil samples and 30.5, 34.4, and 700.2 Bq/kg, respectively, in rock samples. The concentrations of radionuclides in soil samples are found to higher than in rock samples. The concentrations of radionuclides in soil and rock samples in the study area are slightly higher than Indian average and world average values. (author)

Soil classification basing on the spectral characteristics of topsoil samples

Science.gov (United States)

Liu, Huanjun; Zhang, Xiaokang; Zhang, Xinle

2016-04-01

Soil taxonomy plays an important role in soil utility and management, but China has only course soil map created based on 1980s data. New technology, e.g. spectroscopy, could simplify soil classification. The study try to classify soils basing on the spectral characteristics of topsoil samples. 148 topsoil samples of typical soils, including Black soil, Chernozem, Blown soil and Meadow soil, were collected from Songnen plain, Northeast China, and the room spectral reflectance in the visible and near infrared region (400-2500 nm) were processed with weighted moving average, resampling technique, and continuum removal. Spectral indices were extracted from soil spectral characteristics, including the second absorption positions of spectral curve, the first absorption vale's area, and slope of spectral curve at 500-600 nm and 1340-1360 nm. Then K-means clustering and decision tree were used respectively to build soil classification model. The results indicated that 1) the second absorption positions of Black soil and Chernozem were located at 610 nm and 650 nm respectively; 2) the spectral curve of the meadow is similar to its adjacent soil, which could be due to soil erosion; 3) decision tree model showed higher classification accuracy, and accuracy of Black soil, Chernozem, Blown soil and Meadow are 100%, 88%, 97%, 50% respectively, and the accuracy of Blown soil could be increased to 100% by adding one more spectral index (the first two vole's area) to the model, which showed that the model could be used for soil classification and soil map in near future.

Study of Organochlorinated Pesticide Residues and Polychlorinated Biphenyls in Soil Samples

Directory of Open Access Journals (Sweden)

MSc. Vlora Gashi

2013-12-01

Full Text Available This paper presents and discusses the data obtained for organochlorinated pesticides and their residues in the soil samples of agricultural areas. Soil contamination is one of most important factors influencing the quality of agricultural products. Usage of heavy farm equipment, the land drainage, an exces­sive application of agrochemicals, emissions originating from mining, metallurgical, and chemical and coal power plants and transport, all generate a number of undesired substances (nitric and sulphur oxides, PAHs, heavy metals, pesticides, which after deposition in soil may influence crop quality. Thus, input of these contaminants into the environment should be carefully monitored. Levels of organochlorinated pesticides contamination were evaluated in agriculture areas that are in use. 10 soil samples were taken in agricultural areas  Plane of  Dugagjini , Kosovo. Representa­tive soil samples were collected from 0-30 cm top layer of the soil. In the analytical method we combined ultrasonic bath extraction and a Florisil column for samples clean-up. The analysis of the organochlorinated pesticides in soil samples was performed by gas chromatography technique using electron capture detector (GC/ECD. Optima-5 (low/mid polarity, 5% phenyl methyl siloxane 60 m x 0.33 mm x 0.25μm film capillary column was used for isolation and determination of organochlorinated pesticides. Low concentrations of organochlorinated pesticide and their metabolites were found in the studied samples. The presence of organochlorinated pesticides and their residues is probably resulting of their previous uses for agricultural purposes.

Determination of naturally occurring radionuclides in soil samples of Ayranci, Turkey

Science.gov (United States)

Agar, Osman; Eke, Canel; Boztosun, Ismail; Emin Korkmaz, M.

2015-04-01

The specific activity, radiation hazard index and the annual effective dose of the naturally occurring radioactive elements (238U, 232Th and 40K) were determined in soil samples collected from 12 different locations in Ayranci region by using a NaI(Tl) gamma-ray spectrometer. The measured activity concentrations of the natural radionuclides in studied soil samples were compared with the corresponding results of different countries and the internationally reported values. From the analysis, it is found that these materials may be safely used as construction materials and do not pose significant radiation hazards.

Removal of fission products from waste solutions using 16 different soil samples

International Nuclear Information System (INIS)

Bangash, M.A.; Hanif, J.

1997-01-01

Most of the nuclear sites use pits in the surrounding soils for the storage/disposal of low active waste (LAW) solutions. The characteristics of the soil if not suitable for the fixation or adsorption of the radioactive nuclides, may cause migration of these nuclides to hydrosphere. The phenomenon has the risk of radio toxic pollution for the living bodies therefore minerals composing the soil and their adsorption properties need to be investigated. For this purpose 16 different soil samples were collected from all over Pakistan. Mineralogical composition of the soils was determined by X-ray diffraction analysis. It was found that most of the samples contained clay minerals, illite, kaolinite and montmorillonite. Studies for the removal of fission products like, /sup 137/Cs. /sup 60/Sr and activation product /sup 60/CO from solution were carried out on these samples. The sorption experiments were performed by batch technique using radioactive as tracers. Distribution co-efficient were determined by mixing he element solution at pH 3 with the soil at soil solution ratios of 1 to 20. It is revealed from the experimental data that efficient removal of fission products from solutions is achieved by soil samples containing clay mineral montmorillonite, followed by little and kaolinite. These soils thus can be effectively used for the disposal of low level radioactive waste solutions without causing any environmental hazard. (author)

The Impact of Soil Sampling Errors on Variable Rate Fertilization

Energy Technology Data Exchange (ETDEWEB)

R. L. Hoskinson; R C. Rope; L G. Blackwood; R D. Lee; R K. Fink

2004-07-01

Variable rate fertilization of an agricultural field is done taking into account spatial variability in the soil’s characteristics. Most often, spatial variability in the soil’s fertility is the primary characteristic used to determine the differences in fertilizers applied from one point to the next. For several years the Idaho National Engineering and Environmental Laboratory (INEEL) has been developing a Decision Support System for Agriculture (DSS4Ag) to determine the economically optimum recipe of various fertilizers to apply at each site in a field, based on existing soil fertility at the site, predicted yield of the crop that would result (and a predicted harvest-time market price), and the current costs and compositions of the fertilizers to be applied. Typically, soil is sampled at selected points within a field, the soil samples are analyzed in a lab, and the lab-measured soil fertility of the point samples is used for spatial interpolation, in some statistical manner, to determine the soil fertility at all other points in the field. Then a decision tool determines the fertilizers to apply at each point. Our research was conducted to measure the impact on the variable rate fertilization recipe caused by variability in the measurement of the soil’s fertility at the sampling points. The variability could be laboratory analytical errors or errors from variation in the sample collection method. The results show that for many of the fertility parameters, laboratory measurement error variance exceeds the estimated variability of the fertility measure across grid locations. These errors resulted in DSS4Ag fertilizer recipe recommended application rates that differed by up to 138 pounds of urea per acre, with half the field differing by more than 57 pounds of urea per acre. For potash the difference in application rate was up to 895 pounds per acre and over half the field differed by more than 242 pounds of potash per acre. Urea and potash differences

Isolation of antimicrobial producing Actinobacteria from soil samples

Directory of Open Access Journals (Sweden)

Afaf Ahmed Elbendary

2018-01-01

Full Text Available Emergence of multidrug resistant bacteria has made the search for novel bioactive compounds from natural and unexplored habitats a necessity. Actinobacteria have important bioactive substances. The present study investigated antimicrobial activity of Actinobacteria isolated from soil samples of Egypt. One hundred samples were collected from agricultural farming soil of different governorates. Twelve isolates have produced activity against the tested microorganisms (S. aureus, Bacillus cereus, E. coli, K. pneumoniae, P. aeruginosa, S. Typhi, C. albicans, A. niger and A. flavus. By VITEK 2 system version: 07.01 the 12 isolates were identified as Kocuria kristinae, Kocuria rosea, Streptomyces griseus, Streptomyces flaveolus and Actinobacteria. Using ethyl acetate extraction method the isolates culture’s supernatants were tested by diffusion method against indicator microorganisms. These results indicate that Actinobacteria isolated from Egypt farms could be sources of antimicrobial bioactive substances.

Collection and processing of plant, animal and soil samples from Bikini, Enewetak and Rongelap Atolls

Energy Technology Data Exchange (ETDEWEB)

Stuart, M.L.

1995-09-01

The United States used the Marshall Islands for its nuclear weapons program testing site from 1946 to 1958. The BRAVO test was detonated at Bikini Atoll on March 1, 1954. Due to shifting wind conditions at the time of the nuclear detonation, many of the surrounding Atolls became contaminated with fallout (radionuclides carried by the wind currents). Lawrence Livermore National Laboratory`s (LLNL) Marshall Islands Project has been responsible for the collecting, processing, and analyzing of food crops, vegetation, soil, water, animals, and marine species to characterize the radionuclides in the environment, and to estimate dose at atolls that may have been contaminated. Tropical agriculture experiments reducing the uptake of {sup 137}Cs have been conducted on Bikini Atoll. The Marshall Islands field team and laboratory processing team play an important role in the overall scheme of the Marshall Islands Dose Assessment and Radioecology Project. This report gives a general description of the Marshall Islands field sampling and laboratory processing procedures currently used by our staff.

Collection and processing of plant, animal and soil samples from Bikini, Enewetak and Rongelap Atolls

International Nuclear Information System (INIS)

Stuart, M.L.

1995-09-01

The United States used the Marshall Islands for its nuclear weapons program testing site from 1946 to 1958. The BRAVO test was detonated at Bikini Atoll on March 1, 1954. Due to shifting wind conditions at the time of the nuclear detonation, many of the surrounding Atolls became contaminated with fallout (radionuclides carried by the wind currents). Lawrence Livermore National Laboratory's (LLNL) Marshall Islands Project has been responsible for the collecting, processing, and analyzing of food crops, vegetation, soil, water, animals, and marine species to characterize the radionuclides in the environment, and to estimate dose at atolls that may have been contaminated. Tropical agriculture experiments reducing the uptake of 137 Cs have been conducted on Bikini Atoll. The Marshall Islands field team and laboratory processing team play an important role in the overall scheme of the Marshall Islands Dose Assessment and Radioecology Project. This report gives a general description of the Marshall Islands field sampling and laboratory processing procedures currently used by our staff

Source Identification and Sequential Leaching of Heavy Metals in Soil Samples Collected from Selected Dump Sites in Ekiti State, Nigeria

OpenAIRE

, E.E. Awokunmi; , S.S. Asaolu; , O.O Ajayi; , A.O. Adebayo

2011-01-01

Ten heavy metals (Fe, Cu, Mn, Zn, Pb, Ni, Co, Cd, Cr and Sn) in fractioned and bulk soil samples collected from four dump sites located in AdoEkiti and Ikere -Ekiti, South western Nigeria were analysed using a modified Tessier’s procedure and acid digestion to obtain the distribution pattern of metal in this region. The metals were found to have been distributed in all phases with Fe, Cr, and Sn dominating the residual fraction (90.12 - 94.88%), Co, Ni, Cu, and Zn were found in all the extrac...

Composite Sampling Approaches for Bacillus anthracis Surrogate Extracted from Soil.

Directory of Open Access Journals (Sweden)

Brian France

Full Text Available Any release of anthrax spores in the U.S. would require action to decontaminate the site and restore its use and operations as rapidly as possible. The remediation activity would require environmental sampling, both initially to determine the extent of contamination (hazard mapping and post-decon to determine that the site is free of contamination (clearance sampling. Whether the spore contamination is within a building or outdoors, collecting and analyzing what could be thousands of samples can become the factor that limits the pace of restoring operations. To address this sampling and analysis bottleneck and decrease the time needed to recover from an anthrax contamination event, this study investigates the use of composite sampling. Pooling or compositing of samples is an established technique to reduce the number of analyses required, and its use for anthrax spore sampling has recently been investigated. However, use of composite sampling in an anthrax spore remediation event will require well-documented and accepted methods. In particular, previous composite sampling studies have focused on sampling from hard surfaces; data on soil sampling are required to extend the procedure to outdoor use. Further, we must consider whether combining liquid samples, thus increasing the volume, lowers the sensitivity of detection and produces false negatives. In this study, methods to composite bacterial spore samples from soil are demonstrated. B. subtilis spore suspensions were used as a surrogate for anthrax spores. Two soils (Arizona Test Dust and sterilized potting soil were contaminated and spore recovery with composites was shown to match individual sample performance. Results show that dilution can be overcome by concentrating bacterial spores using standard filtration methods. This study shows that composite sampling can be a viable method of pooling samples to reduce the number of analysis that must be performed during anthrax spore remediation.

Determination of metals in scots pine (Pinus Sylvestris) needles and soil samples

International Nuclear Information System (INIS)

Ludborzs, A.; Viksna, A.

2000-01-01

Current report is the finding to apply two modern and powerful methods of microanalysis - Total Reflection X-ray Fluorescence Spectrometry (TXRF) and Graphite Furnace Atomic Absorption Spectrometry - for the analysis of biological and geological materials. For some of the measurements Instrumental Neutron Activation Analysis (INAA) has been used as an arbitrary method. The goal of the research project is to find possible relationships between metals content in the Scots pine (Pinus sylvestris) needles and the soil samples, which have been taken under the trees. The objectives of the work are analysis of both needles and soils, pH measurements of the soil samples, and handling of a simplified metal speciation analysis in the soil samples. For statistical reliability of the project, seven pine trees from different locations in Latvia have been chosen as the analysis objects. Samples of 20 different age class needles have been collected from the trees and 21 soil sample has been sampled under the trees. K, Ca, Mn, Fe, Zn, Rb, Sr, Pb, and Cd content have been analysed in both samples of the needles and the soils. The obtained measurement data have been processed according to the aim of the project. Relevant questions about causal differences of metal concentrations in different age classes of needles, about subtle working principles of the plant's root system, about the role of some elements in the plant's living processes still remain unanswered. (author)

The concentration of Cs, Sr and other elements in water samples collected in a paddy field

International Nuclear Information System (INIS)

Ban-nai, Tadaaki; Hisamatsu, Shun'ichi; Yanai-Kudo, Masumi; Hasegawa, Hidenao; Torikai, Yuji

2000-01-01

To research elemental concentrations in soil water in a paddy field, samples of the soil water were collected with porous Teflon resin tubes which were buried in the field. The soil water collections were made at various depth, 2.5, 12.5, 25 and 35 cm from the surface in the paddy field, located in Rokkasho, Aomori, once every two weeks during the rice cultivation period, from May to October in 1998. The paddy field was irrigated from May 7th to July 20th, dried from July 20th to August 5th, then again irrigated until September 16th. Drastic changes of the alkaline earth metal elements, Fe and Mn in soil water samples were seen at the beginning and end of the midsummer drainage. The concentrations of Cs, Fe, Mn and NH 4 in soil water samples showed a similar variation pattern to that of alkaline earth metal elements in the waterlogged period. The change of redox potential was considered a possible cause for the concentration variation for these substances. (author)

Contamination of apple orchard soils and fruit trees with copper-based fungicides: sampling aspects.

Science.gov (United States)

Wang, Quanying; Liu, Jingshuang; Liu, Qiang

2015-01-01

Accumulations of copper in orchard soils and fruit trees due to the application of Cu-based fungicides have become research hotspots. However, information about the sampling strategies, which can affect the accuracy of the following research results, is lacking. This study aimed to determine some sampling considerations when Cu accumulations in the soils and fruit trees of apple orchards are studied. The study was conducted in three apple orchards from different sites. Each orchard included two different histories of Cu-based fungicides usage, varying from 3 to 28 years. Soil samples were collected from different locations varying with the distances from tree trunk to the canopy drip line. Fruits and leaves from the middle heights of tree canopy at two locations (outer canopy and inner canopy) were collected. The variation in total soil Cu concentrations between orchards was much greater than the variation within orchards. Total soil Cu concentrations had a tendency to increase with the increasing history of Cu-based fungicides usage. Moreover, total soil Cu concentrations had the lowest values at the canopy drip line, while the highest values were found at the half distances between the trunk and the canopy drip line. Additionally, Cu concentrations of leaves and fruits from the outer parts of the canopy were significantly higher than from the inner parts. Depending on the findings of this study, not only the between-orchard variation but also the within-orchard variation should be taken into consideration when conducting future soil and tree samplings in apple orchards.

Field sampling of soil pore water to evaluate trace element mobility and associated environmental risk

Energy Technology Data Exchange (ETDEWEB)

Moreno-Jimenez, Eduardo, E-mail: eduardo.moreno@uam.es [Departamento de Quimica Agricola, Universidad Autonoma de Madrid, 28049 Madrid (Spain); Beesley, Luke [James Hutton Institute, Craigiebuckler, Aberdeen AB15 8QH (United Kingdom); Lepp, Nicholas W. [35, Victoria Road, Formby, Liverpool L37 7DH (United Kingdom); Dickinson, Nicholas M. [Department of Ecology, Lincoln University, Lincoln 7647, PO Box 84 (New Zealand); Hartley, William [School of Computing, Science and Engineering, University of Salford, Cockcroft Building, Salford, M5 4WT (United Kingdom); Clemente, Rafael [Dep. of Soil and Water Conservation and Organic Waste Management, CEBAS-CSIC, Campus Universitario de Espinardo, PO Box 164, 30100 Espinardo, Murcia (Spain)

2011-10-15

Monitoring soil pollution is a key aspect in sustainable management of contaminated land but there is often debate over what should be monitored to assess ecological risk. Soil pore water, containing the most labile pollutant fraction in soils, can be easily collected in situ offering a routine way to monitor this risk. We present a compilation of data on concentration of trace elements (As, Cd, Cu, Pb, and Zn) in soil pore water collected in field conditions from a range of polluted and non-polluted soils in Spain and the UK during single and repeated monitoring, and propose a simple eco-toxicity test using this media. Sufficient pore water could be extracted for analysis both under semi-arid and temperate conditions, and eco-toxicity comparisons could be effectively made between polluted and non-polluted soils. We propose that in-situ pore water extraction could enhance the realism of risk assessment at some contaminated sites. - Highlights: > In situ pore water sampling successfully evaluates trace elements mobility in soils. > Field sampling proved robust for different soils, sites and climatic regimes. > Measurements may be directly related to ecotoxicological assays. > Both short and long-term monitoring of polluted lands may be achieved. > This method complements other widely used assays for environmental risk assessment. - In situ pore water sampling from a wide variety of soils proves to be a beneficial application to monitor the stability of pollutants in soils and subsequent risk through mobility.

Analysis of Mars Analogue Soil Samples Using Solid-Phase Microextraction, Organic Solvent Extraction and Gas Chromatography/Mass Spectrometry

Science.gov (United States)

Orzechowska, G. E.; Kidd, R. D.; Foing, B. H.; Kanik, I.; Stoker, C.; Ehrenfreund, P.

2011-01-01

Polycyclic aromatic hydrocarbons (PAHs) are robust and abundant molecules in extraterrestrial environments. They are found ubiquitously in the interstellar medium and have been identified in extracts of meteorites collected on Earth. PAHs are important target molecules for planetary exploration missions that investigate the organic inventory of planets, moons and small bodies. This study is part of an interdisciplinary preparation phase to search for organic molecules and life on Mars. We have investigated PAH compounds in desert soils to determine their composition, distribution and stability. Soil samples (Mars analogue soils) were collected at desert areas of Utah in the vicinity of the Mars Desert Research Station (MDRS), in the Arequipa region in Peru and from the Jutland region of Denmark. The aim of this study was to optimize the solid-phase microextraction (SPME) method for fast screening and determination of PAHs in soil samples. This method minimizes sample handling and preserves the chemical integrity of the sample. Complementary liquid extraction was used to obtain information on five- and six-ring PAH compounds. The measured concentrations of PAHs are, in general, very low, ranging from 1 to 60 ng g(sup -1). The texture of soils is mostly sandy loam with few samples being 100% silt. Collected soils are moderately basic with pH values of 8-9 except for the Salten Skov soil, which is slightly acidic. Although the diverse and variable microbial populations of the samples at the sample sites might have affected the levels and variety of PAHs detected, SPME appears to be a rapid, viable field sampling technique with implications for use on planetary missions.

Occurrence and species distribution of pathogenic Mucorales in unselected soil samples from France.

Science.gov (United States)

Mousavi, B; Costa, J M; Arné, P; Guillot, J; Chermette, R; Botterel, F; Dannaoui, E

2018-04-01

Mucormycosis is a life-threatening invasive fungal disease that affects a variety of patient groups. Although Mucorales are mostly opportunistic pathogens originating from soil or decaying vegetation, there are currently few data on prevalence of this group of fungi in the environment. The aim of the present study was to assess the prevalence and diversity of species of Mucorales from soil samples collected in France. Two grams of soil were homogenized in sterile saline and plated on Sabouraud dextrose agar and RPMI agar supplemented with itraconazole or voriconazole. Both media contained chloramphenicol and gentamicin. The plates were incubated at 35 ± 2 °C and checked daily for fungal growth for a maximum of 7 d. Mucorales were subcultured for purity. Each isolate was identified phenotypically and molecular identification was performed by ITS sequencing. A total of 170 soil samples were analyzed. Forty-one isolates of Mucorales were retrieved from 38 culture-positive samples. Among the recovered isolates, 27 Rhizopus arrhizus, 11 Mucor circinelloides, one Lichtheimia corymbifera, one Rhizopus microsporus and one Cunninghamella bertholletiae were found. Positive soil samples came from cultivated fields but also from other types of soil such as flower beds. Mucorales were retrieved from samples obtained in different geographical regions of France. Voriconazole-containing medium improved the recovery of Mucorales compared with other media. The present study showed that pathogenic Mucorales are frequently recovered from soil samples in France. Species diversity should be further analyzed on a larger number of soil samples from different geographic areas in France and in other countries.

Bioremediation of PAH contaminated soil samples

International Nuclear Information System (INIS)

Joshi, M.M.; Lee, S.

1994-01-01

Soils contaminated with polynuclear aromatic hydrocarbons (PAHs) pose a hazard to life. The remediation of such sites can be done using physical, chemical, and biological treatment methods or a combination of them. It is of interest to study the decontamination of soil using bioremediation. The experiments were conducted using Acinetobacter (ATCC 31012) at room temperature without pH or temperature control. In the first series of experiments, contaminated soil samples obtained from Alberta Research Council were analyzed to determine the toxic contaminant and their composition in the soil. These samples were then treated using aerobic fermentation and removal efficiency for each contaminant was determined. In the second series of experiments, a single contaminant was used to prepare a synthetic soil sample. This sample of known composition was then treated using aerobic fermentation in continuously stirred flasks. In one set of flasks, contaminant was the only carbon source and in the other set, starch was an additional carbon source. In the third series of experiments, the synthetic contaminated soil sample was treated in continuously stirred flasks in the first set and in fixed bed in the second set and the removal efficiencies were compared. The removal efficiencies obtained indicated the extent of biodegradation for various contaminants, the effect of additional carbon source, and performance in fixed bed without external aeration

Radon mass exhalation rate in soil samples at South Bengaluru city, Karnataka, India

International Nuclear Information System (INIS)

Poojitha, C.G.; Pranesha, T.S.; Ganesh, K.E.; Sahoo, B.K.; Sapra, B.K.

2017-01-01

Radon mass exhalation rate in soil samples collected from different locations of South Bengaluru city were measured using scintillation based Smart radon thoron monitor (RnDuo). It has been observed that the mass exhalation rate estimated due to presence of radon concentration in soil samples ranges from 39.18 - 265.58 mBq/kg/h with an average value of 115.64 mBq/kg/h. Finally we compare our results with similar investigation from different parts of India. (author)

Soil forensics: How far can soil clay analysis distinguish between soil vestiges?

Science.gov (United States)

Corrêa, R S; Melo, V F; Abreu, G G F; Sousa, M H; Chaker, J A; Gomes, J A

2018-03-01

Soil traces are useful as forensic evidences because they frequently adhere to individuals and objects associated with crimes and can place or discard a suspect at/from a crime scene. Soil is a mixture of organic and inorganic components and among them soil clay contains signatures that make it reliable as forensic evidence. In this study, we hypothesized that soils can be forensically distinguished through the analysis of their clay fraction alone, and that samples of the same soil type can be consistently distinguished according to the distance they were collected from each other. To test these hypotheses 16 Oxisol samples were collected at distances of between 2m and 1.000m, and 16 Inceptisol samples were collected at distances of between 2m and 300m from each other. Clay fractions were extracted from soil samples and analyzed for hyperspectral color reflectance (HSI), X-ray diffraction crystallographic (XRD), and for contents of iron oxides, kaolinite and gibbsite. The dataset was submitted to multivariate analysis and results were from 65% to 100% effective to distinguish between samples from the two soil types. Both soil types could be consistently distinguished for forensic purposes according to the distance that samples were collected from each other: 1000m for Oxisol and 10m for Inceptisol. Clay color and XRD analysis were the most effective techniques to distinguish clay samples, and Inceptisol samples were more easily distinguished than Oxisol samples. Soil forensics seems a promising field for soil scientists as soil clay can be useful as forensic evidence by using routine analytical techniques from soil science. Copyright © 2017 The Chartered Society of Forensic Sciences. Published by Elsevier B.V. All rights reserved.

Study of lead pollution in air, soil and water samples of Quetta city

International Nuclear Information System (INIS)

Khan, M.; Khan, G.M.; Akbar, S.; Panezai, M.A.; Haq, Z.U.

2011-01-01

This study briefly presents the collected data of lead pollution in the environment of Quetta City in Balochistan, Pakistan. The samples were collected from different sites. The analysis of lead was carried out in underground water samples, the exhaust of different vehicles, roadside and sewage soils from selected points of Quetta City. The average discharge resulted in deposition by motorcycles (29.12 g/h), cars (44.47 g/h), wagons (176.54 g/h) and buses (141.52 g/h). The maximum deposition was 222.96 g/h from auto-rickshaws. The value for lead in smoke of different vehicles seems quite high when extrapolated to the large number of such vehicles for a longer time. The concentration of lead in roadside soil varied from 73.3 mg/kg (T and T closed colony) to 731.9 mg/kg (Sirki road bus-stop). The average content of lead in sewage soil of City Nala is 1250.6 mg/kg. The level of lead was more than WHO standards for such soils. The lead quantity in all 24 tube- well water samples, was slightly above the WHO standards (10 macro g/L).The results of this study were comparable to similar study in twin cities of Rawalpindi and islamabad. (author)

Study of Cs/sup 137/ contamination in soil and food samples of Jhangar valley, Pakistan

International Nuclear Information System (INIS)

Chaudhry, Z.S.; Khan, H.M.; Aslam, M.; Iqbal, S.; Orfi, S.D.

2001-01-01

Chernobyl accident has been the main source of artificial radioactive contamination throughout the world and its effects have been found in Pakistan as well. In the present study, activities of an important anthropogenic radionuclide, Cs/sup 137/ in soil and food samples of Jhangar Valley of Pakistan have been determined using PC based gamma spectrometer. Soil-375 from IAEA was used as reference material. The soil samples were collected from the agricultural fields of the selected area while food samples, grown in the selected area, were collected from the fields or from local market. After proper treatment, the samples were analyzed using a high purity germanium (HPGe) detector. The following values for average specific activity of Cs/sup 137/ were found: soil (range 1.3-46.8 Bq/kg) (12.0 Bq/kg), wheat (0.9 +- 0.05 Bq/kg), millet (1.5 +- 0.06 Bq/kg), lentils (2.0 +- 0.1 Bq/kg), potato (0.6 +- 0.03 Bq/kg) and cauliflower (0.6 +- 0.03 Bq/kg). The results have been discussed and compared with other data available in the literature. (author)

Response of soil aggregate stability to storage time of soil samples

International Nuclear Information System (INIS)

Gerzabek, M.H.; Roessner, H.

1993-04-01

The aim of the present study was to investigate the well known phenomenon of changing aggregate stability values as result of soil sample storage. In order to evaluate the impact of soil microbial activity, the soil sample was split into three subsamples. Two samples were sterilized by means of chloroform fumigation and gamma irradiation, respectively. However, the aggregate stability measurements at three different dates were not correlated with the microbial activity (dehydrogenase activity). The moisture content of the aggregate samples seems to be of higher significance. Samples with lower moisture content (range: 0.4 to 1.9%) exhibited higher aggregate stabilities. Thus, airdried aggregate samples without further treatment don't seem to be suitable for standardized stability measurements. (authors)

Determination of 137Cs activities in soil samples from east and south Marmara region, Turkey

International Nuclear Information System (INIS)

Kilic, Oe.; Belivermis, M.; Cotuk, Y.; Coskun, M.; Cayir, A.; Kuecer, R.

2006-01-01

Activity concentrations of 1 37Cs, 4 0K and physico-chemical parameters of soil samples collected from 99 sampling stations in the east and south of Marmara Region of Turkey were determined. The study region was divided into 20 x 20 km grids and soil samples collected randomly in each square from 0-5 cm surface layer. Activities were measured by means of multichannel gamma analyser provided with high purity germanium detector. Relations among 1 37Cs concentrations and physico-chemical parameters of soils and climatic factors of the region were evaluated. Arc View GIS version 3.1 was used mapping of study area. Distribution of radionuclide concentrations in the region illustrated with contour maps using Surfer 8.0 for Windows. The range of activity concentrations of 1 37Cs and 4 0K were measured to be 0.92-153.72 and 69.24-1085.57 Bq/kg respectively

Selenium speciation in acidic environmental samples: application to acid rain-soil interaction at Mount Etna volcano.

Science.gov (United States)

Floor, Geerke H; Iglesías, Mònica; Román-Ross, Gabriela; Corvini, Philippe F X; Lenz, Markus

2011-09-01

Speciation plays a crucial role in elemental mobility. However, trace level selenium (Se) speciation analyses in aqueous samples from acidic environments are hampered due to adsorption of the analytes (i.e. selenate, selenite) on precipitates. Such solid phases can form during pH adaptation up till now necessary for chromatographic separation. Thermodynamic calculations in this study predicted that a pHpH eluent that matches the natural sample pH of acid rain-soil interaction samples from Etna volcano was developed. With a mobile phase containing 20mM ammonium citrate at pH 3, selenate and selenite could be separated in different acidic media (spiked water, rain, soil leachates) in rain-soil interaction using synthetic rain based on H(2)SO(4) and soil samples collected at the flanks of Etna volcano demonstrated the dominance of selenate over selenite in leachates from samples collected close to the volcanic craters. This suggests that competitive behavior with sulfate present in acid rain might be a key factor in Se mobilization. The developed speciation method can significantly contribute to understand Se cycling in acidic, Al/Fe rich environments. Copyright © 2011 Elsevier Ltd. All rights reserved.

A quantitative method to detect explosives and selected semivolatiles in soil samples by Fourier transform infrared spectroscopy

International Nuclear Information System (INIS)

Clapper-Gowdy, M.; Dermirgian, J.; Robitaille, G.

1995-01-01

This paper describes a novel Fourier transform infrared (FTIR) spectroscopic method that can be used to rapidly screen soil samples from potentially hazardous waste sites. Samples are heated in a thermal desorption unit and the resultant vapors are collected and analyzed in a long-path gas cell mounted in a FTIR. Laboratory analysis of a soil sample by FTIR takes approximately 10 minutes. This method has been developed to identify and quantify microgram concentrations of explosives in soil samples and is directly applicable to the detection of selected volatile organics, semivolatile organics, and pesticides

Distribution coefficient Kd in surface soils collected in Aomori prefecture

International Nuclear Information System (INIS)

Tsukada, Hirofumi; Hasegawa, Hidenao; Hisamatsu, Shun'ichi; Inaba, Jiro

2000-01-01

Soil-solution distribution coefficients (Kds), which are the ratio of an element concentration in a soil solid phase to that in a solution phase, for 32 elements in Andosols, Wet Andosols and Gleyed Andosols collected throughout Aomori Prefecture were determined. A dried soil sample was mixed with a 10-fold amount of pure water in a PPCO centrifuge tube, and then gently shaken for 24 h. The Kd values were obtained by measurement of element concentrations in solid and solution phases (batch method). The Kd values in this work were up to three orders of magnitude higher than the IAEA reported values, and their 95% confidence intervals were within two orders of magnitude. Most Kd values of elements were decreasing with increasing electrical conductivity of the solution phase. The Kd of Ca had a good correlation with that of Sr. However, the correlation between the Kds of K and Cs was not good. The Kd values were also determined by another method. The soil solutions were separated from the fresh soil samples by means of high speed centrifuging. The Kd values were calculated from the element concentration in solid phase and soil solution (centrifugation method). The Kd values obtained by the centrifugation method agreed within one order of magnitude with those by the batch method, and both variation patterns in elements correlated well. (author)

Application of instrument neutron-activation analysis in a comparative investigation of soil samples

Energy Technology Data Exchange (ETDEWEB)

Dimitrov, D. (Institute po Kriminalistika i Kriminologiya, Sofia (Bulgaria))

1983-01-01

A quantitative measurement of the contents of 17 chemical elements in soil samples, collected using the existing network from the surface of five cultivated areas in Bulgaria has been carried out. The values obtained have been used to calculate the evaluations psub(i) of the dispersions and for the ordering of the chemical elements according to their importance in criminology. The possibility for criminological comparison of single soil samples using the contents of the five most important elements - Th, Fe, Sc, Ce and Mn has been shown.

Determination of Pu in soil samples

International Nuclear Information System (INIS)

Torres C, C. O.; Hernandez M, H.; Romero G, E. T.; Vega C, H. R.

2016-10-01

The irreversible consequences of accidents occurring in nuclear plants and in nuclear fuel reprocessing sites are mainly the distribution of different radionuclides in different matrices such as the soil. The distribution in the superficial soil is related to the internal and external exposure to the radiation of the affected population. The internal contamination with radionuclides such as Pu is of great relevance to the nuclear forensic science, where is important to know the chemical and isotopic compositions of nuclear materials. The objective of this work is to optimize the radiochemical separation of plutonium (Pu) from soil samples and to determine their concentration. The soil samples were prepared using acid digestion assisted by microwave; purification of Pu was carried out with AG1X8 resin using ion exchange chromatography. Pu isotopes were measured using ICP-SFMS. In order to reduce the interference due to the presence of "2"3"8UH "+ in the samples, a solvent removal system (Apex) was used. In addition, the limit of detection and quantification of Pu was determined. It was found that the recovery efficiency of Pu in soil samples ranges from 70 to 93%. (Author)

Analysis Of Non-Volatile Toxic Heavy Metals (Cd, Pb, Cu,Cr And Zn) In ALLIUM SATIVUM (Garlic) And Soil Samples ,Collected From Different Locations Of Punjab, Pakistan By Atomic Absorption Spectroscopy

OpenAIRE

Ata S.; Tayyab S.; Rasool A.

2013-01-01

Garlic is one of the most widely used medicinal plants. The monitoring of toxic metals such as lead, Cadmium, Chromium, Copper and Zinc in garlic and the soil of garlic fields collected from ten different cities of Punjab is critical for preventing public health against the hazards of metal toxicity. The levels of toxic heavy metals in garlic and soil samples were investigated using Atomic absorption spectrometer. The metal content in garlic samples was found to be in increasing order as Cr> ...

Analysis of soil samples from Gebeng area using NAA technique

Science.gov (United States)

Elias, Md Suhaimi; Wo, Yii Mei; Hamzah, Mohd Suhaimi; Shukor, Shakirah Abd; Rahman, Shamsiah Ab; Salim, Nazaratul Ashifa Abdullah; Azman, Muhamad Azfar; Hashim, Azian

2017-01-01

Rapid development and urbanization will increase number of residence and industrial area. Without proper management and control of pollution, these will give an adverse effect to environment and human life. The objective of this study to identify and quantify key contaminants into the environment of the Gebeng area as a result of industrial and human activities. Gebeng area was gazetted as one of the industrial estate in Pahang state. Assessment of elemental pollution in soil of Gebeng area base on level of concentration, enrichment factor and geo-accumulation index. The enrichment factors (EFs) were determined by the elemental rationing method, whilst the geo-accumulation index (Igeo) by comparing of current to continental crustal average concentration of element. Twenty-seven of soil samples were collected from Gebeng area. Soil samples were analysed by using Neutron Activation Analyses (NAA) technique. The obtained data showed higher concentration of iron (Fe) due to abundance in soil compared to other elements. The results of enrichment factor showed that Gebeng area have enrich with elements of As, Br, Hf, Sb, Th and U. Base on the geo-accumulation index (Igeo) classification, the soil quality of Gebeng area can be classified as class 0, (uncontaminated) to Class 3, (moderately to heavily contaminated).

Sampling depth confounds soil acidification outcomes

Science.gov (United States)

In the northern Great Plains (NGP) of North America, surface sampling depths of 0-15 or 0-20 cm are suggested for testing soil characteristics such as pH. However, acidification is often most pronounced near the soil surface. Thus, sampling deeper can potentially dilute (increase) pH measurements an...

Latin Hypercube Sampling (LHS) at variable resolutions for enhanced watershed scale Soil Sampling and Digital Soil Mapping.

Science.gov (United States)

Hamalainen, Sampsa; Geng, Xiaoyuan; He, Juanxia

2017-04-01

Latin Hypercube Sampling (LHS) at variable resolutions for enhanced watershed scale Soil Sampling and Digital Soil Mapping. Sampsa Hamalainen, Xiaoyuan Geng, and Juanxia, He. AAFC - Agriculture and Agr-Food Canada, Ottawa, Canada. The Latin Hypercube Sampling (LHS) approach to assist with Digital Soil Mapping has been developed for some time now, however the purpose of this work was to complement LHS with use of multiple spatial resolutions of covariate datasets and variability in the range of sampling points produced. This allowed for specific sets of LHS points to be produced to fulfil the needs of various partners from multiple projects working in the Ontario and Prince Edward Island provinces of Canada. Secondary soil and environmental attributes are critical inputs that are required in the development of sampling points by LHS. These include a required Digital Elevation Model (DEM) and subsequent covariate datasets produced as a result of a Digital Terrain Analysis performed on the DEM. These additional covariates often include but are not limited to Topographic Wetness Index (TWI), Length-Slope (LS) Factor, and Slope which are continuous data. The range of specific points created in LHS included 50 - 200 depending on the size of the watershed and more importantly the number of soil types found within. The spatial resolution of covariates included within the work ranged from 5 - 30 m. The iterations within the LHS sampling were run at an optimal level so the LHS model provided a good spatial representation of the environmental attributes within the watershed. Also, additional covariates were included in the Latin Hypercube Sampling approach which is categorical in nature such as external Surficial Geology data. Some initial results of the work include using a 1000 iteration variable within the LHS model. 1000 iterations was consistently a reasonable value used to produce sampling points that provided a good spatial representation of the environmental

Chemical and geotechnical analyses of soil samples from Olkiluoto for studies on sorption in soils

International Nuclear Information System (INIS)

Lusa, M.; Aemmaelae, K.; Hakanen, M.; Lehto, J.; Lahdenperae, A.-M.

2009-05-01

The safety assessment of disposal of spent nuclear fuel will include an estimate on the behavior of nuclear waste nuclides in the biosphere. As a part of this estimate also the transfer of nuclear waste nuclides in the soil and sediments is to be considered. In this study soil samples were collected from three excavator pits in Olkiluoto and the geotechnical and chemical characteristics of the samples were determined. In later stage these results will be used in sorption tests. Aim of these tests is to determine the Kd-values for Cs, Tc and I and later for Mo, Nb and Cl. Results of these sorption tests will be reported later. The geotechnical characteristics studied included dry weight and organic matter content as well as grain size distribution and mineralogy analyses. Selective extractions were carried out to study the sorption of cations into different mineral types. The extractions included five steps in which the cations bound to exchangeable, carbonate, oxides of Fe and Mn, organic matter and residual fractions were determined. For all fractions ICPMS analyses were carried out. In these analyses Li, Na, Mg, K, Ca, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Sr, Mo, Cd, Cs and Pb were determined. In addition six profiles were taken from the surroundings of two excavator pits for the 137 Cs determination. Besides the samples taken for the characterization of soil, supplement samples were taken from the same layers for the separation of soil water. From the soil water pH, DOC, anions (F, Cl, NO 3 , SO 4 ) and cations (Na, Mg, K, Ca, Al, Cr, Mn, Fe, Ni, Cu, Zn, As, S, Cd, Cs, Pb, U) were determined. (orig.)

Application of instrument neutron-activation analysis in a comparative investigation of soil samples

International Nuclear Information System (INIS)

Dimitrov, D.

1983-01-01

A quantitative measurement of the contents of 17 chemical elements in soil samples, collected using the existing network from the surface of five cultivated areas in Bulgaria has been carried out. The values obtained have been used to calculate the evaluations psub(i) of the dispersions and for the ordering of the chemical elements according to their importance in criminology. The possibility for criminological comparison of single soil samples using the contents of the five most important elements - Th, Fe, Sc, Ce and Mn has been shown. (author)

Including Below Detection Limit Samples in Post Decommissioning Soil Sample Analyses

Energy Technology Data Exchange (ETDEWEB)

Kim, Jung Hwan; Yim, Man Sung [KAIST, Daejeon (Korea, Republic of)

2016-05-15

To meet the required standards the site owner has to show that the soil at the facility has been sufficiently cleaned up. To do this one must know the contamination of the soil at the site prior to clean up. This involves sampling that soil to identify the degree of contamination. However there is a technical difficulty in determining how much decontamination should be done. The problem arises when measured samples are below the detection limit. Regulatory guidelines for site reuse after decommissioning are commonly challenged because the majority of the activity in the soil at or below the limit of detection. Using additional statistical analyses of contaminated soil after decommissioning is expected to have the following advantages: a better and more reliable probabilistic exposure assessment, better economics (lower project costs) and improved communication with the public. This research will develop an approach that defines an acceptable method for demonstrating compliance of decommissioned NPP sites and validates that compliance. Soil samples from NPP often contain censored data. Conventional methods for dealing with censored data sets are statistically biased and limited in their usefulness.

Measurement of radioactive nuclides present in soil samples of district Ganderbal of Kashmir Province for radiation safety purposes

Directory of Open Access Journals (Sweden)

Feroz A. Mir

2015-04-01

Full Text Available Assessment of radioactive elements in the residential area is very important from different points of view especially for human health. The aim of present survey was focused on determining the current radon exhalation rate and radium concentration in soil samples collected from some areas of the Ganderbal district, Jammu and Kashmir, India. “Can technique” has been employed for the measurement of radon exhalation rate and radium concentration in soil samples collected from under study areas. The Uranium concentration in these soil samples where estimated by using the fission track registration technique (using LR-115 plastic track detectors.The uranium concentration was found to varies between 2.03 and 3.52 ppm. The radon exhalation rate in these samples has been found to vary from 5.05 to 21.89 m Bq kg−1 h−1. Radium concentration in soil samples varies from 6.43 to 18.89 Bq kg−1. The calculated values of Uranium concentration in these soil/rock samples are quite lower than the risk level. Radon and radium values found in these samples are also lower than that of optimum value. Hence these areas can be considered as risk free zones from human health point of view.

1996 Phase 2 soil sampling at the 183-H Solar Evaporation Basin site

International Nuclear Information System (INIS)

Kramer, C.D.

1996-10-01

This report consolidates 1996 soil sampling data collected from the 183-H Solar Evaporation Basin Site. This report is intended to be a data reference and does not make comparisons or conclusions regarding specific regulatory criteria. Chemical and radiological data were collected to support cleanup activities at the Hanford Site; soil sampling occurred beneath and next to the former basin structures. The 183-H Solar Evaporation Basins, which consisted of four adjoining concrete basins, were located in the 100 Area of the Hanford Site, north of the retired 105-H Reactor. Originally, the basins were built as part of the 100-H water treatment structures. The four basins were inactive from the mid-1960's until 1973 when radioactive and dangerous (mixed) waste from the 300 Area Fuel Fabrication Facility was shipped to the basins for storage and treatment. The basins were used for solar evaporation of the waste. The last shipment of waste to the 183-H Basins took place in November 1985. Decontamination of the cement structure took place in 1995. The structure has subsequently been dismantled and disposed. Chapters 2.0 through 4.0 present summary information about sampling (1) beneath the loading ramp and berm piles, (2) in shallow soils beneath the former basin floor, and (3) deep vadose soils. Detailed data are provided in the appendices

Determination of mercury in ash and soil samples by oxygen flask combustion method-Cold vapor atomic fluorescence spectrometry (CVAFS)

International Nuclear Information System (INIS)

Geng Wenhua; Nakajima, Tsunenori; Takanashi, Hirokazu; Ohki, Akira

2008-01-01

A simple method was developed for the determination of mercury (Hg) in coal fly ash (CFA), waste incineration ash (WIA), and soil by use of oxygen flask combustion (OFC) followed by cold vapor atomic fluorescence spectrometry (CVAFS). A KMnO 4 solution was used as an absorbent in the OFC method, and the sample containing a combustion agent and an ash or soil sample was combusted by the OFC method. By use of Hg-free graphite as the combustion agent, the determination of Hg in ash and soil was successfully carried out; the Hg-free graphite was prepared by use of a mild pyrolysis procedure at 500 deg. C. For six certified reference materials (three CFA samples and three soil samples), the values of Hg obtained by this method were in good agreement with the certified or reference values. In addition, real samples including nine CFAs collected from some coal-fired power plants, five WIAs collected from waste incineration plants, and two soils were analyzed by the present method, and the data were compared to those from microwave-acid digestion (MW-AD) method

Radionuclides, Heavy Metals, and Polychlorinated Biphenyls in Soils Collected Around the Perimeter of Low-Level Radioactive Waste Disposal Area G during 2006

International Nuclear Information System (INIS)

P. R. Fresquez

2007-01-01

Twenty-one soil surface samples were collected in March around the perimeter of Area G, the primary disposal facility for low-level radioactive solid waste at Los Alamos National Laboratory (LANL). Three more samples were collected in October around the northwest corner after elevated tritium levels were detected on an AIRNET station located north of pit 38 in May. Also, four soil samples were collected along a transect at various distances (48, 154, 244, and 282 m) from Area G, starting from the northeast corner and extending to the Pueblo de San Ildefonso fence line in a northeasterly direction (this is the main wind direction). Most samples were analyzed for radionuclides ( 3 H, 238 Pu, 239,240 Pu, 241 Am, 234 U, 235 U, and 238 U), inorganic elements (Al, Ba, Be, Ca, Cr, Co, Cu, Fe, Mg, Mn, Ni, K, Na, V, Hg, Zn, Sb, As, Cd, Pb, Se, Ag, and Tl) and polychlorinated biphenyl (PCB) concentrations. As in previous years, the highest levels of 3 H in soils (690 pCi/mL) were detected along the south portion of Area G near the 3 H shafts; whereas, the highest concentrations of 241 Am (1.2 pCi/g dry) and the Pu isotopes (1.9 pCi/g dry for 238 Pu and 5 pCi/g dry for 239,240 Pu) were detected along the northeastern portions near the transuranic waste pads. Concentrations of 3 H in three soil samples and 241 Am and Pu isotopes in one soil sample collected around the northwest corner in October increased over concentrations found in soils collected at the same locations earlier in the year. Almost all of the heavy metals, with the exception of Zn and Sb in one sample each, in soils around the perimeter of Area G were below regional statistical reference levels (mean plus three standard deviations) (RSRLs). Similarly, only one soil sample collected on the west side contained PCB concentrations--67 (micro)g/kg dry of aroclor-1254 and 94 (micro)g/kg dry of aroclor-1260. Radionuclide and inorganic element concentrations in soils collected along a transect from Area G to the

Evaluation of some pollutant levels in environmental samples collected from the area of the new campus of Taif University.

Science.gov (United States)

Sharshar, Taher; Hassan, H Ebrahim; Arida, Hassan A; Aydarous, Abdulkadir; Bazaid, Salih A; Ahmed, Mamdouh A

2013-01-01

The levels of radioactivity and heavy metals in soil, plant and groundwater samples collected from the area of the new campus of Taif University, Saudi Arabia, and its neighbouring areas have been determined. High-resolution gamma-ray spectroscopy was used for radioactivity measurements, and inductively coupled plasma atomic emission spectroscopy was used to determine the concentration of heavy metals. The means of (226)Ra, (228)Ra and (40)K concentrations in water samples collected from four wells were found to be 0.13 ± 0.03, 0.05 ± 0.03 and 1.3 ± 0.5 Bq l(-1), respectively. The means of (238)U, (226)Ra, (228)Ra ((232)Th for soil samples) and (40)K concentrations in wild plant and soil samples were found to be 3.7 ± 4.1, 8.8 ± 11.6, 3.8 ± 2.9 and 1025 ± 685, and 8.6 ± 3.4, 12.8 ± 3.4, 16.6 ± 7.1 and 618 ± 82 Bq kg(-1) dry weight (DW), respectively. The (137)Cs of artificial origin was also detected in soil samples with a mean concentration of 3.8 ± 2.2 Bq kg(-1) DW. Evaluating the results, it can be concluded that the concentrations of (238)U, (226)Ra, (232)Th and (40)K in soil samples fall within the world average. Furthermore, 19 trace and major elements in groundwater samples and 22 elements in soil and plant samples were determined. The sampling locations of soil can be classified into three groups (relatively high, medium and low polluted) according to their calculated metal pollution index using the contents of trace and major elements. A cluster analysis of the contents of radioactivity and trace element contents in soil samples shows the presence of two main distinct clusters of sampling locations.

An assessment of the natural radioactivity distribution and radiation hazard in soil samples from Qatar using high-resolution gamma-ray spectrometry

Science.gov (United States)

Al-Sulaiti, Huda; Al Mugren, K. S.; Bradley, D. A.; Regan, P. H.; Santawamaitre, T.; Malain, D.; Habib, A.; Nasir, Tabassum; Alkhomashi, N.; Al-Dahan, N.; Al-Dosari, M.; Bukhari, S.

2017-11-01

We establish baseline measurements for radioactivity concentration in the soil samples collected from the Qatarian peninsula. The work focused on the naturally occurring and technically enhanced levels of radiation associated with 235,8U and 232Th natural decay chains and the long-lived naturally occurring radionuclide 40K in 129 soil samples collected across the landscape of the State of Qatar. Three radiological distribution maps showing the activity concentrations of 226Ra, 232Th and 40K were constructed. Two soil samples were found to be elevated to the favour of 226Ra concentration and significantly above the average and global values. Notably, these samples were collected from an area within an oil field (NW Dukhan). The mean values of activity concentrations of 226Ra, 232Th and 40K for the full cohort of samples were found to be 17.2±1.6, 6.38±0.26 and 169±5 Bq/kg, respectively. These values lie within the expected range relative to the world average values in soil samples of 30, 35 and 400 Bq/kg, respectively.

Classification of Surface and Deep Soil Samples Using Linear Discriminant Analysis

International Nuclear Information System (INIS)

Wasim, M.; Ali, M.; Daud, M.

2015-01-01

A statistical analysis was made of the activity concentrations measured in surface and deep soil samples for natural and anthropogenic gamma-emitting radionuclides. Soil samples were obtained from 48 different locations in Gilgit, Pakistan covering about 50 km/sup 2/ areas at an average altitude of 1550 m above sea level. From each location two samples were collected: one from the top soil (2-6 cm) and another from a depth of 6-10 cm. Four radionuclides including /sup 226/Ra, /sup 232/Th, /sup 40/K and /sup 137/Cs were quantified. The data was analyzed using t-test to find out activity concentration difference between the surface and depth samples. At the surface, the median activity concentrations were 23.7, 29.1, 4.6 and 115 Bq kg/sup -1/ for 226Ra, 232Th, 137Cs and 40K respectively. For the same radionuclides, the activity concentrations were respectively 25.5, 26.2, 2.9 and 191 Bq kg/sup -1/ for the depth samples. Principal component analysis (PCA) was applied to explore patterns within the data. A positive significant correlation was observed between the radionuclides /sup 226/Ra and /sup 232/Th. The data from PCA was further utilized in linear discriminant analysis (LDA) for the classification of surface and depth samples. LDA classified surface and depth samples with good predictability. (author)

Validated sampling strategy for assessing contaminants in soil stockpiles

International Nuclear Information System (INIS)

Lame, Frank; Honders, Ton; Derksen, Giljam; Gadella, Michiel

2005-01-01

Dutch legislation on the reuse of soil requires a sampling strategy to determine the degree of contamination. This sampling strategy was developed in three stages. Its main aim is to obtain a single analytical result, representative of the true mean concentration of the soil stockpile. The development process started with an investigation into how sample pre-treatment could be used to obtain representative results from composite samples of heterogeneous soil stockpiles. Combining a large number of random increments allows stockpile heterogeneity to be fully represented in the sample. The resulting pre-treatment method was then combined with a theoretical approach to determine the necessary number of increments per composite sample. At the second stage, the sampling strategy was evaluated using computerised models of contaminant heterogeneity in soil stockpiles. The now theoretically based sampling strategy was implemented by the Netherlands Centre for Soil Treatment in 1995. It was applied to all types of soil stockpiles, ranging from clean to heavily contaminated, over a period of four years. This resulted in a database containing the analytical results of 2570 soil stockpiles. At the final stage these results were used for a thorough validation of the sampling strategy. It was concluded that the model approach has indeed resulted in a sampling strategy that achieves analytical results representative of the mean concentration of soil stockpiles. - A sampling strategy that ensures analytical results representative of the mean concentration in soil stockpiles is presented and validated

Soil sample moisture content as a function of time during oven drying for gamma-ray spectroscopic measurements

International Nuclear Information System (INIS)

Benke, R.R.; Kearfott, K.J.

1999-01-01

In routine gamma-ray spectroscopic analysis of collected soil samples, procedure often calls to remove soil moisture by oven drying overnight at a temperature of 100 deg. C . Oven drying not only minimizes the gamma-ray self-attenuation of soil samples due to the absence of water during the gamma-ray spectroscopic analysis, but also allows for a straightforward calculation of the specific activity of radionuclides in soil, historically based on the sample dry weight. Because radon exhalation is strongly dependent on moisture , knowledge of the oven-drying time dependence of the soil moisture content, combined with radon exhalation measurements during oven drying and at room temperature for varying soil moisture contents, would allow conclusions to be made on how the oven-drying radon exhalation rate depends on soil moisture content. Determinations of the oven-drying radon exhalation from soil samples allow corrections to be made for the immediate laboratory gamma-ray spectroscopy of radionuclides in the natural uranium decay chain. This paper presents the results of soil moisture content measurements during oven drying and suggests useful empirical fits to the moisture data

Use of X-ray diffraction technique and chemometrics to aid soil sampling strategies in traceability studies.

Science.gov (United States)

Bertacchini, Lucia; Durante, Caterina; Marchetti, Andrea; Sighinolfi, Simona; Silvestri, Michele; Cocchi, Marina

2012-08-30

Aim of this work is to assess the potentialities of the X-ray powder diffraction technique as fingerprinting technique, i.e. as a preliminary tool to assess soil samples variability, in terms of geochemical features, in the context of food geographical traceability. A correct approach to sampling procedure is always a critical issue in scientific investigation. In particular, in food geographical traceability studies, where the cause-effect relations between the soil of origin and the final foodstuff is sought, a representative sampling of the territory under investigation is certainly an imperative. This research concerns a pilot study to investigate the field homogeneity with respect to both field extension and sampling depth, taking also into account the seasonal variability. Four Lambrusco production sites of the Modena district were considered. The X-Ray diffraction spectra, collected on the powder of each soil sample, were treated as fingerprint profiles to be deciphered by multivariate and multi-way data analysis, namely PCA and PARAFAC. The differentiation pattern observed in soil samples, as obtained by this fast and non-destructive analytical approach, well matches with the results obtained by characterization with other costly analytical techniques, such as ICP/MS, GFAAS, FAAS, etc. Thus, the proposed approach furnishes a rational basis to reduce the number of soil samples to be collected for further analytical characterization, i.e. metals content, isotopic ratio of radiogenic element, etc., while maintaining an exhaustive description of the investigated production areas. Copyright © 2012 Elsevier B.V. All rights reserved.

Performance evaluation soil samples utilizing encapsulation technology

Science.gov (United States)

Dahlgran, James R.

1999-01-01

Performance evaluation soil samples and method of their preparation using encapsulation technology to encapsulate analytes which are introduced into a soil matrix for analysis and evaluation by analytical laboratories. Target analytes are mixed in an appropriate solvent at predetermined concentrations. The mixture is emulsified in a solution of polymeric film forming material. The emulsified solution is polymerized to form microcapsules. The microcapsules are recovered, quantitated and introduced into a soil matrix in a predetermined ratio to form soil samples with the desired analyte concentration.

Analysis of natural radionuclides in soil samples of Purola area of Garhwal Himalaya, India.

Science.gov (United States)

Yadav, Manjulata; Rawat, Mukesh; Dangwal, Anoop; Prasad, Mukesh; Gusain, G S; Ramola, R C

2015-11-01

Naturally occurring radioactive materials are widely spread in the earth's environment, being distributed in soil, rocks, water, air, plants and even within the human body. All of these sources have contributed to an increase in the levels of environmental radioactivity and population radiation doses. This paper presents the activity level due to the presence of (226)Ra, (232)Th and (40)K in soil samples of Purola area in Garhwal Himalaya region. The measured activity of (226)Ra, (232)Th and (40)K in collected soil samples of Purola was found to vary from 13±10 to 55±10 Bq kg(-1) with an average of 31±2 Bq kg(-1), 13±10 to 101±13 Bq kg(-1) with an average 30±3 Bq kg(-1) and 150±81 to 1310±154 Bq kg(-1) with an average 583±30 Bq kg(-1), respectively. The radium equivalent activity in collected soil samples was found to vary from 47 to 221 Bq kg(-1) with an average of 115 Bq kg(-1). The total absorbed gamma dose rate in this area was found to vary from 22 to 93 nGy h(-1) with an average of 55 nGy h(-1). The distribution of these radionuclides in the soil of study area is discussed in details. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Radioactivity measurements of soil samples in the Region Vranje (Bratoselce Village) for the period 2001-2004

International Nuclear Information System (INIS)

Eremic-savkovic, M.; Pantelic, G.; Tanaskovic, I.; Vuletic, V.; Javorina, L.

2006-01-01

Systematic examination of radioactive contamination of soil samples was established at the Institute for Occupational and Radiological Health. With the bombing of our country (Spring 1999) the monitoring of radioactivity has changed. We also measured the activities of uranium and it descendants. This paper presents the results of radioactivity monitoring of the soil in small area 700 m near village Bratoselce in region Vranje during the period 2001 - 2004. From 2001 to 2004, we collected different samples from this fenced area as well as outside this area assuming not to be contaminated, before, during and after decontamination. Some soil samples were made as a mix of small samples from a large area of location. Other samples were taken at the points formerly designated as contaminated or from shell-craters seen on the fenced area surface. All samples were analyzed by gamma spectrometry and measurements of alpha and beta activity. On the basis of measurements of soil activities, analysis of 238 U and 235 U, as well as in comparison with natural activity ratio being 21.4, it may be concluded that depleted uranium contamination was present both in the fenced area and outside it, because this ratio in the samples of soil was found to be 34 to 73. Natural activity in soil samples was slightly higher in relation to mean soil activity in Serbia. (authors)

EDRXF measurements of heavy elements in soil samples from some potentially polluted sites in zambia

International Nuclear Information System (INIS)

Hayumbu, P.; Phiri, L.K.; Mambo, A.; Sokotela, S.B.

2001-01-01

A survey of heavy element levels in top soils collected around four industrial plants and along four highway stretches demonstrated that there was significant pollution only around an abandoned Pb/Zn mine. Sample collection in a rectangular grid encompassing each source sought to depict the spatial extent of pollution. Ascertaining levels of heavy elements in potentially polluted soils in urban areas of Zambia and along major highways was deemed desirable because it is common practice to grow maize and vegetables in lots adjacent to accessible industrial sites and highways. Pb is a heavy element of interest for all sampled sites whose distribution at the abandoned mine ranged from 13 to 2028 ppm

Collecting soil vapor from the Vadose Zone with an instrumented membrane system

International Nuclear Information System (INIS)

Martins, S.A.

1992-07-01

As part of an on-going program to monitor ground water pollution, the SEAMIST instrumented membrane system was purchased and installed in two boreholes at the Lawrence Livermore National Laboratory (LLNL). SEAMIST is a flexible, removable, polyvinylchloride-coated, nylon membrane tube used to seal the sides of a borehole and to which sampling devices and other types of instrumentation may be attached. This paper describes a method to sample soil vapor (a component of soil gas) with the SEAMIST system from a borehole at several depths simultaneously. The cryotraps used with this technique were tested for their collection efficiency, and those data are presented. Data on the integrity of the SEAMIST borehole seal are also reported

Sampling soils for transuranic nuclides: a review

International Nuclear Information System (INIS)

Fowler, E.B.; Essington, E.H.

1976-01-01

A review of the literature pertinent to the sampling of soils for radionuclides is presented; emphasis is placed on transuranic nuclides. Sampling of soils is discussed relative to systems of heterogeneous distributions and varied particle sizes encountered in certain environments. Sampling methods that have been used for two different sources of contamination, global fallout, and accidental or operational releases, are included

Uranium, radium and radon exhalation study in some soil samples using track etch technique

International Nuclear Information System (INIS)

Harmanjit, Singh; Joga, Singh; Surinder, Singh; Bajwa, B.S.

2006-01-01

Full text of publication follows: Uranium, radium concentration and radon exhalation rates have been determined in the soil samples collected from some areas of Punjab using the L.R.-115 nuclear track detectors. Radium concentration in these samples has been found to be varying from 0.80 to 5.34 Bq Kg-1. The radon exhalation rate in these samples has been found to be varying from 0.99 to 6.60 mBq Kg -1 h -1 (32.82 to 218.49 mBqm -2 h -1 ). A good correlation has been observed between radon exhalation rate and radium concentration observed in the soil samples. The uranium concentration in all these samples is being carried out and the other correlations will also be established. (authors)

Spatial Variation of Soil Lead in an Urban Community Garden: Implications for Risk-Based Sampling.

Science.gov (United States)

Bugdalski, Lauren; Lemke, Lawrence D; McElmurry, Shawn P

2014-01-01

Soil lead pollution is a recalcitrant problem in urban areas resulting from a combination of historical residential, industrial, and transportation practices. The emergence of urban gardening movements in postindustrial cities necessitates accurate assessment of soil lead levels to ensure safe gardening. In this study, we examined small-scale spatial variability of soil lead within a 15 × 30 m urban garden plot established on two adjacent residential lots located in Detroit, Michigan, USA. Eighty samples collected using a variably spaced sampling grid were analyzed for total, fine fraction (less than 250 μm), and bioaccessible soil lead. Measured concentrations varied at sampling scales of 1-10 m and a hot spot exceeding 400 ppm total soil lead was identified in the northwest portion of the site. An interpolated map of total lead was treated as an exhaustive data set, and random sampling was simulated to generate Monte Carlo distributions and evaluate alternative sampling strategies intended to estimate the average soil lead concentration or detect hot spots. Increasing the number of individual samples decreases the probability of overlooking the hot spot (type II error). However, the practice of compositing and averaging samples decreased the probability of overestimating the mean concentration (type I error) at the expense of increasing the chance for type II error. The results reported here suggest a need to reconsider U.S. Environmental Protection Agency sampling objectives and consequent guidelines for reclaimed city lots where soil lead distributions are expected to be nonuniform. © 2013 Society for Risk Analysis.

Determination of strontium-90 in soil samples

Energy Technology Data Exchange (ETDEWEB)

Chang, C C

1976-06-01

The determination of /sup 90/Sr in soil by tri-n-butyl phosphate (TBP) is often interfered with iron which is always present in soil sample. Based on the method given by the U.S. Environmental Protection Agency, HClO/sub 4/ is added to remove iron ions while the soil sample is analyzed with TBP. The effect of different concentrations of HClO/sub 4/ on extraction yield of iron and chemical yield of yttrium is investigated. The experimental results show that 2N HClO/sub 4/ is the optimum concentration. The chemical yield of yttrium can reach about 60 percent, and all iron ions can be removed. This method has successfully been applied to analyze the soil samples taken from the site of the nuclear power plant in North Taiwan.

Soil separator and sampler and method of sampling

Science.gov (United States)

O'Brien, Barry H [Idaho Falls, ID; Ritter, Paul D [Idaho Falls, ID

2010-02-16

A soil sampler includes a fluidized bed for receiving a soil sample. The fluidized bed may be in communication with a vacuum for drawing air through the fluidized bed and suspending particulate matter of the soil sample in the air. In a method of sampling, the air may be drawn across a filter, separating the particulate matter. Optionally, a baffle or a cyclone may be included within the fluidized bed for disentrainment, or dedusting, so only the finest particulate matter, including asbestos, will be trapped on the filter. The filter may be removable, and may be tested to determine the content of asbestos and other hazardous particulate matter in the soil sample.

An assessment of the natural radioactivity distribution and radiation hazard in soil samples from Qatar using high-resolution gamma-ray spectrometry

International Nuclear Information System (INIS)

Al-Sulaiti, Huda; Al Mugren, K.S.; Bradley, D.A.; Regan, P.H.; Santawamaitre, T.; Malain, D.; Habib, A.; Nasir, Tabassum; Alkhomashi, N.; Al-Dahan, N.; Al-Dosari, M.; Bukhari, S.

2017-01-01

We establish baseline measurements for radioactivity concentration in the soil samples collected from the Qatarian peninsula. The work focused on the naturally occurring and technically enhanced levels of radiation associated with 235,8 U and 232 Th natural decay chains and the long-lived naturally occurring radionuclide 40 K in 129 soil samples collected across the landscape of the State of Qatar. Three radiological distribution maps showing the activity concentrations of 226 Ra, 232 Th and 40 K were constructed. Two soil samples were found to be elevated to the favour of 226 Ra concentration and significantly above the average and global values. Notably, these samples were collected from an area within an oil field (NW Dukhan). The mean values of activity concentrations of 226 Ra, 232 Th and 40 K for the full cohort of samples were found to be 17.2±1.6, 6.38±0.26 and 169±5 Bq/kg, respectively. These values lie within the expected range relative to the world average values in soil samples of 30, 35 and 400 Bq/kg, respectively. - Highlights: • This study aimed to establish a baseline for soil radioactivity in Qatar. • The work focused on measurement of NORM levels in 129 samples using HPGe detector. • The mean values lie within the range relative to the world average values. • The Ac of Dukhan soil samples were elevated. • The mean of D, Ra eq , H ex and AEDE had all normal levels of radiation.

Natural radioactivity measurements in soil samples from Hamirpur district, Himachal Pradesh, India

International Nuclear Information System (INIS)

Singh, Surinder; Singh, Baldev; Kumar, Ajay

2003-01-01

Radium, thorium and potassium analysis have been made in soil samples collected from some villages of Hamirpur district, Himachal Pradesh, India using gamma ray spectrometry. The work has been undertaken keeping in view the health hazard effects of these radioelements in the environment. The results for radium activity are also compared using track etch technique employing radon alpha method developed by Somogyi (Technical reports series no. 310, vol. 1, IAEA, Vienna, 1990, p. 229). The measurements have been taken using 5''x4'' NaI(Tl) detector. The gamma ray lines of 1.46, 1.76 and 2.62 MeV were employed for potassium, radium and thorium analysis. The results for radium content in soil obtained by gamma ray spectrometry agrees with that determined by the track etch technique. The radium activity in soil samples of Hamirpur district is found to be within the safe limits

Thorium, uranium and rare earth elements concentration in weathered Japanese soil samples

International Nuclear Information System (INIS)

Sahoo, Sarata Kumar; Hosoda, Masahiro; Kamagata, Sadatoshi; Sorimachi, Atsuyuki; Ishikawa, Tetsuo; Tokonami, Shinji; Uchida, Shigeo

2011-01-01

The geochemical behavior of thorium, uranium and rare earth elements (REEs) are relatively close to one another while compared to other elements in a geological environment. Radioactive elements like 232 Th and 238 U along with their decay products (e.g. 226 Ra) are present in most environmental matrices and can be transferred to living bodies by different pathways which can lead to the sources of exposure to man. For these reasons, it has been necessary to monitor those natural radionuclides in weathered soil samples to assess the possible hazards. It has been observed that granitic rocks contain higher amounts of U, Th and light REEs compared to other igneous rocks such as basalt and andesites. To better understand the interaction between REEs and soils, the nature of soils must be considered. In this paper, we discussed the distribution pattern of 232 Th and 238 U along with REEs in soil samples of weathered acid rock (granite and ryolite) collected from two prefectures of Japan: (1) Kobe city in Hyogo prefecture and (2) Mutsu city and Higashidori village in Aomori prefecture. (author)

Chemical profile of size-fractionated soils collected in a semiarid industrial area of Argentina

Science.gov (United States)

Morales Del Mastro, Anabella; Pereyra, Marcelo; Londonio, Agustín; Pereyra, Victoria; Rebagliati, Raúl Jiménez; Dawidowski, Laura; Gómez, Darío; Smichowski, Patricia

2014-12-01

A study was undertaken to assess the chemical profile of soil collected in Bahía Blanca (Argentina). In this industrial city, semiarid soils are affected by different industrial and agricultural activities, the presence of a saltpeter extraction facility, traffic and increasing urbanization. Sixteen soil samples (superficial and sub-superficial) were collected. Samples were sieved in two fractions (A plasma optical emission spectrometry (ICP OES). Anions (Cl-, F-, SO42-) and cations (K+, Na+ and NH4+) were determined by high performance liquid chromatography (HPLC) after an aqueous extraction. As expected, crustal elements namely, Al, Ca, Fe, Mg and Ti exhibited the highest concentrations. Mean elemental concentration ranged from Na+ ≅ SO42- > K+ > NO3-. Three indicators, namely, (i) coefficient of variation, (ii) coefficient of divergence and (iii) ratio of elemental concentration with respect to Ca were used to assess chemical, spatial and inter-profile variability. Chloride > Ca > Na+ > Mo > SO42-, dominated the variability indicating that these are key chemical markers for future assessment of crustal contribution to airborne particles in the area. The ratios Xi/Ca allowed discriminating the soil of the semi-arid region surrounding Bahía Blanca. The chemical profiles obtained in this study, particularly those of topsoil, will be a key input to characterize soil resuspension and its contribution to airborne particulate matter in a forthcoming receptor model analysis.

Sample collection and documentation

International Nuclear Information System (INIS)

Cullings, Harry M.; Fujita, Shoichiro; Watanabe, Tadaaki; Yamashita, Tomoaki; Tanaka, Kenichi; Endo, Satoru; Shizuma, Kiyoshi; Hoshi, Masaharu; Hasai, Hiromi

2005-01-01

Beginning within a few weeks after the bombings and periodically during the intervening decades, investigators in Hiroshima and Nagasaki have collected samples of materials that were in the cities at the time of the bombings. Although some early efforts were not driven by specific measurement objectives, many others were. Even some of the very earliest samples collected in 1945 were based on carefully conceived research plans and detailed specifications for samples appropriate to particular retrospective measurements, i.e., of particular residual quantities remaining from exposure to the neutrons and gamma rays from the bombs. This chapter focuses mainly on the work of groups at two institutions that have actively collaborated since the 1980s in major collection efforts and have shared samples among themselves and with other investigators: the Radiation Effects Research Foundation (RERF) and its predecessor the Atomic Bomb Casualty Commission (ABCC), and Hiroshima University. In addition, a number of others are listed, who also contributed to the literature by their collection of samples. (J.P.N.)

A soil sampling intercomparison exercise for the ALMERA network

Energy Technology Data Exchange (ETDEWEB)

Belli, Maria [Istituto Superiore per la Protezione e la Ricerca Ambientale (ISPRA), Via di Castel Romano 100, I-00128 Roma (Italy)], E-mail: maria.belli@apat.it; Zorzi, Paolo de [Istituto Superiore per la Protezione e la Ricerca Ambientale (ISPRA), Via di Castel Romano 100, I-00128 Roma (Italy)], E-mail: paolo.dezorzi@isprambiente.it; Sansone, Umberto [International Atomic Energy Agency (IAEA), Agency' s Laboratories Seibersdorf, A-2444 Seibersdorf (Austria)], E-mail: u.sansone@iaea.org; Shakhashiro, Abduhlghani [International Atomic Energy Agency (IAEA), Agency' s Laboratories Seibersdorf, A-2444 Seibersdorf (Austria)], E-mail: a.shakhashiro@iaea.org; Gondin da Fonseca, Adelaide [International Atomic Energy Agency (IAEA), Agency' s Laboratories Seibersdorf, A-2444 Seibersdorf (Austria)], E-mail: a.gondin-da-fonseca-azeredo@iaea.org; Trinkl, Alexander [International Atomic Energy Agency (IAEA), Agency' s Laboratories Seibersdorf, A-2444 Seibersdorf (Austria)], E-mail: a.trinkl@iaea.org; Benesch, Thomas [International Atomic Energy Agency (IAEA), Agency' s Laboratories Seibersdorf, A-2444 Seibersdorf (Austria)], E-mail: t.benesch@iaea.org

2009-11-15

Soil sampling and analysis for radionuclides after an accidental or routine release is a key factor for the dose calculation to members of the public, and for the establishment of possible countermeasures. The IAEA organized for selected laboratories of the ALMERA (Analytical Laboratories for the Measurement of Environmental Radioactivity) network a Soil Sampling Intercomparison Exercise (IAEA/SIE/01) with the objective of comparing soil sampling procedures used by different laboratories. The ALMERA network is a world-wide network of analytical laboratories located in IAEA member states capable of providing reliable and timely analysis of environmental samples in the event of an accidental or intentional release of radioactivity. Ten ALMERA laboratories were selected to participate in the sampling exercise. The soil sampling intercomparison exercise took place in November 2005 in an agricultural area qualified as a 'reference site', aimed at assessing the uncertainties associated with soil sampling in agricultural, semi-natural, urban and contaminated environments and suitable for performing sampling intercomparison. In this paper, the laboratories sampling performance were evaluated.

A soil sampling intercomparison exercise for the ALMERA network

International Nuclear Information System (INIS)

Belli, Maria; Zorzi, Paolo de; Sansone, Umberto; Shakhashiro, Abduhlghani; Gondin da Fonseca, Adelaide; Trinkl, Alexander; Benesch, Thomas

2009-01-01

Soil sampling and analysis for radionuclides after an accidental or routine release is a key factor for the dose calculation to members of the public, and for the establishment of possible countermeasures. The IAEA organized for selected laboratories of the ALMERA (Analytical Laboratories for the Measurement of Environmental Radioactivity) network a Soil Sampling Intercomparison Exercise (IAEA/SIE/01) with the objective of comparing soil sampling procedures used by different laboratories. The ALMERA network is a world-wide network of analytical laboratories located in IAEA member states capable of providing reliable and timely analysis of environmental samples in the event of an accidental or intentional release of radioactivity. Ten ALMERA laboratories were selected to participate in the sampling exercise. The soil sampling intercomparison exercise took place in November 2005 in an agricultural area qualified as a 'reference site', aimed at assessing the uncertainties associated with soil sampling in agricultural, semi-natural, urban and contaminated environments and suitable for performing sampling intercomparison. In this paper, the laboratories sampling performance were evaluated.

Naturally Occurring Radionuclides and Rare Earth Elements Pattern in Weathered Japanese Soil Samples

International Nuclear Information System (INIS)

Sahoo, S.K.; Hosoda, M.; Takahashi, H.; Sorimachi, A.; Ishikawa, T.; Tokonami, S.; Uchida, S.

2011-01-01

From the viewpoint of radiation protection, determination of natural radionuclides e.g. thorium and uranium in soil samples are important. Accurate methods for determination of Th and U is gaining importance. The geochemical behavior of Th, U and rare earth elements (REEs) are relatively close to one another while compared to other elements in geological environment. Radioactive elements like 232 Th and 238 U along with their decay products (e.g. 226 Ra) are present in most of the environmental matrices and can be transferred to living bodies by different pathways that can lead to sources of exposure of man. Therefore, it is necessary to monitor these natural radionuclides in weathered soil samples to assess the possible hazards. The activity concentrations of 226 Ra, 228 Th, and 40 K in soils have been measured using a g γ-ray spectroscopy system with high purity germanium detector. The thorium, uranium and REEs were determined from the same sample using inductively coupled plasma mass spectrometry (ICP-MS). Granitic rocks contain higher amounts of Th, U and light REEs compared to other igneous rocks such as basalt and andesites. Therefore, it is necessary to understand the interaction between REEs and nature of soils, as soils are complex heterogeneous mixture of organic and inorganic solids, water and gases. In this paper, we have discussed about distribution pattern of 226 Ra, 232 Th and 238 U along with REEs in soil samples of weathered acid rock (granite and ryolite) collected from two prefectures in Japan: 1. Gifu and 2. Okinawa. (author)

Norm in soil and sludge samples in Dukhan oil Field, Qatar state

Energy Technology Data Exchange (ETDEWEB)

Al-Kinani, A.T.; Hushari, M.; Al-Sulaiti, Huda; Alsadig, I.A., E-mail: mmhushari@moe.gov.qa [Radiation and Chemical Protection Department, Ministry of Environment, Doha (Qatar)

2015-07-01

The main objective of this work is to measure the activity concentrations of Naturally Occurring radioactive Materials (NORM) produced as a buy products in oil production. The analyses of NORM give available information for guidelines concerning radiation protection. Recently NORM subjected to restricted regulation issued by high legal authority at Qatar state. Twenty five samples of soil from Dukhan onshore oil field and 10 sludge samples collected from 2 offshore fields at Qatar state. High resolution low-level gamma-ray spectrometry used to measure gamma emitters of NORM. The activity concentrations of natural radionuclide in 22 samples from Dukhan oil field, were with average worldwide values . Only three soil samples have high activity concentration of Ra-226 which is more than 185 Bq/kg the exempted level for NORM in the Quatrain regulation. The natural radionuclide activity concentrations of 10 sludge samples from offshore oil fields was greater than 1100Bq/kg the exempted values of NORM set by Quatrain regulation so the sludge need special treatments. The average hazards indices (H{sub ex} , D , and Ra{sub eq}), for the 22 samples were below the word permissible values .This means that the human exposure to such material not impose any radiation risk. The average hazards indices (H{sub ex} , D , and Ra{sub eq}), for 3 soil samples and sludge samples are higher than the published maximal permissible. Thus human exposure to such material impose radiation risk. (author)

Norm in soil and sludge samples in Dukhan oil Field, Qatar state

International Nuclear Information System (INIS)

Al-Kinani, A.T.; Hushari, M.; Al-Sulaiti, Huda; Alsadig, I.A.

2015-01-01

The main objective of this work is to measure the activity concentrations of Naturally Occurring radioactive Materials (NORM) produced as a buy products in oil production. The analyses of NORM give available information for guidelines concerning radiation protection. Recently NORM subjected to restricted regulation issued by high legal authority at Qatar state. Twenty five samples of soil from Dukhan onshore oil field and 10 sludge samples collected from 2 offshore fields at Qatar state. High resolution low-level gamma-ray spectrometry used to measure gamma emitters of NORM. The activity concentrations of natural radionuclide in 22 samples from Dukhan oil field, were with average worldwide values . Only three soil samples have high activity concentration of Ra-226 which is more than 185 Bq/kg the exempted level for NORM in the Quatrain regulation. The natural radionuclide activity concentrations of 10 sludge samples from offshore oil fields was greater than 1100Bq/kg the exempted values of NORM set by Quatrain regulation so the sludge need special treatments. The average hazards indices (H ex , D , and Ra eq ), for the 22 samples were below the word permissible values .This means that the human exposure to such material not impose any radiation risk. The average hazards indices (H ex , D , and Ra eq ), for 3 soil samples and sludge samples are higher than the published maximal permissible. Thus human exposure to such material impose radiation risk. (author)

Diffusion probe for gas sampling in undisturbed soil

DEFF Research Database (Denmark)

Petersen, Søren O

2014-01-01

Soil-atmosphere fluxes of trace gases such as methane (CH4) and nitrous oxide (N2O) are determined by complex interactions between biological activity and soil conditions. Soil gas concentration profiles may, in combination with other information about soil conditions, help to understand emission...... controls. This note describes a simple and robust diffusion probe for soil gas sampling as part of flux monitoring programs. It can be deployed with minimum disturbance of in-situ conditions, also at sites with a high or fluctuating water table. Separate probes are used for each sampling depth...... on peat soils used for grazing showed soil gas concentrations of CH4 and N2O as influenced by topography, site conditions, and season. The applicability of the diffusion probe for trace gas monitoring is discussed....

Comparison of soil sampling and analytical methods for asbestos at the Sumas Mountain Asbestos Site-Working towards a toolbox for better assessment.

Science.gov (United States)

Wroble, Julie; Frederick, Timothy; Frame, Alicia; Vallero, Daniel

2017-01-01

Established soil sampling methods for asbestos are inadequate to support risk assessment and risk-based decision making at Superfund sites due to difficulties in detecting asbestos at low concentrations and difficulty in extrapolating soil concentrations to air concentrations. Environmental Protection Agency (EPA)'s Office of Land and Emergency Management (OLEM) currently recommends the rigorous process of Activity Based Sampling (ABS) to characterize site exposures. The purpose of this study was to compare three soil analytical methods and two soil sampling methods to determine whether one method, or combination of methods, would yield more reliable soil asbestos data than other methods. Samples were collected using both traditional discrete ("grab") samples and incremental sampling methodology (ISM). Analyses were conducted using polarized light microscopy (PLM), transmission electron microscopy (TEM) methods or a combination of these two methods. Data show that the fluidized bed asbestos segregator (FBAS) followed by TEM analysis could detect asbestos at locations that were not detected using other analytical methods; however, this method exhibited high relative standard deviations, indicating the results may be more variable than other soil asbestos methods. The comparison of samples collected using ISM versus discrete techniques for asbestos resulted in no clear conclusions regarding preferred sampling method. However, analytical results for metals clearly showed that measured concentrations in ISM samples were less variable than discrete samples.

Determination of elemental in soil samples from Gebeng area using NAA technique

International Nuclear Information System (INIS)

Md Suhaimi Elias; Wo, Y.M.; Mohd Suhaimi Hamzah

2016-01-01

Rapid development and urbanization will increase number of residence and industrial area. Without proper management and control of pollution, these will give an adverse effect to environment and human life. The objective of this study to identify and quantify key contaminants into the environment of the Gebeng area as a result of industrial and human activities. Gebeng area was gazetted as one of the industrial estate in Pahang state. Assessment of elemental pollution in soil of Gebeng area base on level of concentration, enrichment factor and geo-accumulation index. The enrichment factors (EFs) were determined by the elemental rationing method, whilst the geo-accumulation index (I_g_e_o) by comparing of current to continental crustal average concentration of element. Twenty-seven of soil samples were collected from Gebeng area. Soil samples were analysed by using Neutron Activation Analyses (NAA) technique. The obtained data showed higher concentration of iron (Fe) due to abundance in soil compared to other elements. The results of enrichment factor showed that Gebeng area have enrich with elements of As, Br, Hf, Sb, Th and U. Base on the geo-accumulation index (I_g_e_o) classification, the soil quality of Gebeng area can be classified as class 0, (uncontaminated) to Class 3, (moderately to heavily contaminated). (author)

Analysis of soil samples from OMRE decommissioning project

International Nuclear Information System (INIS)

Simpson, O.D.; Chapin, J.A.; Hine, R.E.; Mandler, J.W.; Orme, M.P.; Soli, G.A.

1979-01-01

In order to establish that the present Organic Moderated Reactor Experiment (OMRE) site does not exceed the criteria for radioactive contamination, samples obtained from the remainder of the facility that was not removed such as soil, concrete pads, various structural materials, and the leach pond area were analyzed to determine their radioactive content. The results of the analyses performed on soil samples are presented. Results of this study indicate that the activity at the OMRE decommissioned area is confined to localized areas (i.e., the leach pond area and reactor area). Comparisons of radionuclide concentrations measured in soil taken from the lip of the leach pond with concentrations in soil obtained outside the Idaho National Engineering Laboratory (INEL) site boundaries indicate that the concentration in the soil at the edge of the leach pond is at background levels. The vertical augering technique was determined to be the best approach for obtaining shallow soil samples at the INEL. Selection of this technique was based on ease of operation and analytical results. Less area is disturbed per sample than with the horizontal trenching and coring techniques. The radionuclide analysis of the samples shows the existence of a few regions in the reactor and leach pond areas that were still above INEL release criteria. These regions have been or are being further decontaminated

Estimation of radon concentration in soil and groundwater samples of Northern Rajasthan, India

International Nuclear Information System (INIS)

Mittal, Sudhir; Asha Rani; Mehra, Rohit

2015-01-01

In the present investigation, analysis of radon concentration in 20 water and soil samples collected from different locations of Bikaner and Jhunjhunu districts of Rajasthan, India has been carried out by using RAD7 an electronic Radon detector. The water samples are taken from hand pumps and tube wells having depths ranging from 50 to 600 feet. All the soil gas measurements have been carried out at 100 cm depth. The measured radon concentration in water samples lies in the range from 0.50 to 22 Bq l -1 with the mean value of 4.42 Bq l -1 . Only in one water sample radon concentration is found to be higher than the safe limit of 11 Bq l -1 recommended US Environmental Protection Agency (USEPA, 1991). The measured value of radon concentration in all ground water samples is within the safe limit from 4 to 40 Bq l -1 recommended by United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR, 2008). The total annual effective dose estimated due to radon concentration in water ranges from 1.37 to 60 μSV y -1 with the mean value of 12.08 μSV y -1 . The total annual effective dose from all locations of our studied area is found to be well within the safe limit 0.1 mSv y -1 recommended by World Health Organization (WHO, 2004) and European Council (ED, 1998). Radon measurement in soil samples varies from 941 to 10050 Bq m -3 with the mean value of 4561 Bq m -3 , The radon concentration observed from the soil samples from our study area lies within the range reported by other investigators. Moreover a positive correlation of radon concentration in water with soil samples has been observed. It was observed that the soil and water of Bikaner and Jhunjhunu districts are suitable for drinking and construction purpose without posing any health hazard. (author)

A soil sampling reference site: The challenge in defining reference material for sampling

International Nuclear Information System (INIS)

De Zorzi, Paolo; Barbizzi, Sabrina; Belli, Maria; Fajgelj, Ales; Jacimovic, Radojko; Jeran, Zvonka; Sansone, Umberto; Perk, Marcel van der

2008-01-01

In the frame of the international SOILSAMP project, funded and coordinated by the Italian Environmental Protection Agency, an agricultural area was established as a reference site suitable for performing soil sampling inter-comparison exercises. The reference site was characterized for trace element content in soil, in terms of the spatial and temporal variability of their mass fraction. Considering that the behaviour of long-lived radionuclides in soil can be expected to be similar to that of some stable trace elements and that the distribution of these trace elements in soil can simulate the distribution of radionuclides, the reference site characterised in term of trace elements, can be also used to compare the soil sampling strategies developed for radionuclide investigations

A soil sampling reference site: The challenge in defining reference material for sampling

Energy Technology Data Exchange (ETDEWEB)

De Zorzi, Paolo [Agenzia per la Protezione dell' Ambiente e per i Servizi Tecnici (APAT), Servizio Metrologia Ambientale, Via di Castel Romano, Rome 100-00128 (Italy)], E-mail: paolo.dezorzi@apat.it; Barbizzi, Sabrina; Belli, Maria [Agenzia per la Protezione dell' Ambiente e per i Servizi Tecnici (APAT), Servizio Metrologia Ambientale, Via di Castel Romano, Rome 100-00128 (Italy); Fajgelj, Ales [International Atomic Energy Agency (IAEA), Agency' s Laboratories Seibersdorf, Vienna A-1400 (Austria); Jacimovic, Radojko; Jeran, Zvonka; Sansone, Umberto [Jozef Stefan Institute, Jamova 39, Ljubljana 1000 (Slovenia); Perk, Marcel van der [Department of Physical Geography, Utrecht University, P.O. Box 80115, TC Utrecht 3508 (Netherlands)

2008-11-15

In the frame of the international SOILSAMP project, funded and coordinated by the Italian Environmental Protection Agency, an agricultural area was established as a reference site suitable for performing soil sampling inter-comparison exercises. The reference site was characterized for trace element content in soil, in terms of the spatial and temporal variability of their mass fraction. Considering that the behaviour of long-lived radionuclides in soil can be expected to be similar to that of some stable trace elements and that the distribution of these trace elements in soil can simulate the distribution of radionuclides, the reference site characterised in term of trace elements, can be also used to compare the soil sampling strategies developed for radionuclide investigations.

A soil sampling reference site: the challenge in defining reference material for sampling.

Science.gov (United States)

de Zorzi, Paolo; Barbizzi, Sabrina; Belli, Maria; Fajgelj, Ales; Jacimovic, Radojko; Jeran, Zvonka; Sansone, Umberto; van der Perk, Marcel

2008-11-01

In the frame of the international SOILSAMP project, funded and coordinated by the Italian Environmental Protection Agency, an agricultural area was established as a reference site suitable for performing soil sampling inter-comparison exercises. The reference site was characterized for trace element content in soil, in terms of the spatial and temporal variability of their mass fraction. Considering that the behaviour of long-lived radionuclides in soil can be expected to be similar to that of some stable trace elements and that the distribution of these trace elements in soil can simulate the distribution of radionuclides, the reference site characterised in term of trace elements, can be also used to compare the soil sampling strategies developed for radionuclide investigations.

Assessing NIR & MIR Spectral Analysis as a Method for Soil C Estimation Across a Network of Sampling Sites

Science.gov (United States)

Spencer, S.; Ogle, S.; Borch, T.; Rock, B.

2008-12-01

Monitoring soil C stocks is critical to assess the impact of future climate and land use change on carbon sinks and sources in agricultural lands. A benchmark network for soil carbon monitoring of stock changes is being designed for US agricultural lands with 3000-5000 sites anticipated and re-sampling on a 5- to10-year basis. Approximately 1000 sites would be sampled per year producing around 15,000 soil samples to be processed for total, organic, and inorganic carbon, as well as bulk density and nitrogen. Laboratory processing of soil samples is cost and time intensive, therefore we are testing the efficacy of using near-infrared (NIR) and mid-infrared (MIR) spectral methods for estimating soil carbon. As part of an initial implementation of national soil carbon monitoring, we collected over 1800 soil samples from 45 cropland sites in the mid-continental region of the U.S. Samples were processed using standard laboratory methods to determine the variables above. Carbon and nitrogen were determined by dry combustion and inorganic carbon was estimated with an acid-pressure test. 600 samples are being scanned using a bench- top NIR reflectance spectrometer (30 g of 2 mm oven-dried soil and 30 g of 8 mm air-dried soil) and 500 samples using a MIR Fourier-Transform Infrared Spectrometer (FTIR) with a DRIFT reflectance accessory (0.2 g oven-dried ground soil). Lab-measured carbon will be compared to spectrally-estimated carbon contents using Partial Least Squares (PLS) multivariate statistical approach. PLS attempts to develop a soil C predictive model that can then be used to estimate C in soil samples not lab-processed. The spectral analysis of soil samples either whole or partially processed can potentially save both funding resources and time to process samples. This is particularly relevant for the implementation of a national monitoring network for soil carbon. This poster will discuss our methods, initial results and potential for using NIR and MIR spectral

Analysis of water and soil from the wetlands of Upper Three Runs Creek. Volume 2A, Analytical data packages September--October 1991 sampling

Energy Technology Data Exchange (ETDEWEB)

Haselow, L.A.; Rogers, V.A. [Westinghouse Savannah River Co., Aiken, SC (United States); Riordan, C.J. [Metcalf and Eddy, Inc. (United States); Eidson, G.W.; Herring, M.K. [Normandeau Associates, Inc. (United States)

1992-08-01

Shallow water and soils along Upper Three Runs Creek (UTRC) and associated wetlands between SRS Road F and Cato Road were sampled for nonradioactive and radioactive constituents. The sampling program is associated with risk evaluations being performed for various regulatory documents in these areas of the Savannah River Site (SRS). WSRC selected fifty sampling sites bordering the Mixed Waste Management Facility (MWMF), F- and H-Area Seepage Basins (FHSB), and the Sanitary Landfill (SL). The analytical results from this study provided information on the water and soil quality in UTRC and its associated wetlands. The analytical results from this investigation indicated that the primary constituents and radiological indicators detected in the shallow water and soils were tritium, gross alpha, radium 226, total radium and strontium 90. This investigation involved the collection of shallow water samples during the Fall of 1991 and the Spring of 1992 at fifty (50) sampling locations. Sampling was performed during these periods to incorporate high and low water table periods. Samples were collected from three sections along UTRC denoted as Phase I (MWMF), Phase II (FHSB) and Phase III (SL). One vibracored soil sample was also collected in each phase during the Fall of 1991. This document is compiled solely of experimental data obtained from the sampling procedures.

Analysis of water and soil from the wetlands of Upper Three Runs Creek. Volume 2B: Analytical data packages, January--February 1992 sampling

Energy Technology Data Exchange (ETDEWEB)

Haselow, L.A.; Rogers, V.A. [Westinghouse Savannah River Co., Aiken, SC (United States); Riordan, C.J. [Metcalf and Eddy (United States); Eidson, G.W.; Herring, M.K. [Normandeau Associates, Inc., Aiken, SC (United States)

1992-08-01

Shallow water and soils along Upper Three Runs Creek (UTRC) and associated wetlands between SRS Road F and Cato Road were sampled for nonradioactive and radioactive constituents. The sampling program is associated with risk evaluations being performed for various regulatory documents in these areas of the Savannah River Site (SRS). WSRC selected fifty sampling sites bordering the Mixed Waste Management Facility (MWMF), F- and H-Area Seepage Basins (FHSB), and the Sanitary Landfill (SL). The analytical results from this study provided information on the water and soil quality in UTRC and its associated wetlands. The analytical results from this investigation indicated that the primary constituents and radiological indicators detected in the shallow water and soils were tritium, gross alpha, radium 226, total radium and strontium 90. This investigation involved the collection of shallow water samples during the Fall of 1991 and the Spring of 1992 at fifty (50) sampling locations. Sampling was performed during these periods to incorporate high and low water table periods. Samples were collected from three sections along UTRC denoted as Phase I (MWMF), Phase II (FHSB) and Phase III (SL). One vibracored soil sample was also collected in each phase during the Fall of 1991. This document is compiled of experimental data obtained from the sampling procedures.

Sample sizes to control error estimates in determining soil bulk density in California forest soils

Science.gov (United States)

Youzhi Han; Jianwei Zhang; Kim G. Mattson; Weidong Zhang; Thomas A. Weber

2016-01-01

Characterizing forest soil properties with high variability is challenging, sometimes requiring large numbers of soil samples. Soil bulk density is a standard variable needed along with element concentrations to calculate nutrient pools. This study aimed to determine the optimal sample size, the number of observation (n), for predicting the soil bulk density with a...

Analysis Of Non-Volatile Toxic Heavy Metals (Cd, Pb, Cu,Cr And Zn In ALLIUM SATIVUM (Garlic And Soil Samples ,Collected From Different Locations Of Punjab, Pakistan By Atomic Absorption Spectroscopy

Directory of Open Access Journals (Sweden)

Ata S.

2013-04-01

Full Text Available Garlic is one of the most widely used medicinal plants. The monitoring of toxic metals such as lead, Cadmium, Chromium, Copper and Zinc in garlic and the soil of garlic fields collected from ten different cities of Punjab is critical for preventing public health against the hazards of metal toxicity. The levels of toxic heavy metals in garlic and soil samples were investigated using Atomic absorption spectrometer. The metal content in garlic samples was found to be in increasing order as Cr> Pb> Cd> Cu> Zn. Infield metal content in the soil also followed the same trend. In garlic samples, Pb, Cd, Cr, Zn and Cu ranged from 0.039mg/L to 0.757mg/L, N.D to 1.211mg/L, 0.03mg/L to 0.451mg/L, 0.02mg/Lto0.42mg/L and 0.451mg/L to 0.893mg/L respectively. In soil samples, Pb, Cd, Cr, Zn and Cu were ranged from 0.459mg/L to 0.797mg/L, 0.205mg/L to1.062mg/L, 0.074mg/L to 2.598mg/L, 0.124mg/L to 0.276mg/L and 0.494mg/L to 0.921mg/L respectively. In our study, the Pb and Cd was found more in garlic from Gujranwala and Jaranwala, Cu and Zn were more in samples from Kasur while Cr was predominant in sample from Sheikhupura. Heavy metal content in soil and garlic samples was within the permissible limits proposed by World Health Organization (WHO.

Method for spiking soil samples with organic compounds

DEFF Research Database (Denmark)

Brinch, Ulla C; Ekelund, Flemming; Jacobsen, Carsten S

2002-01-01

We examined the harmful side effects on indigenous soil microorganisms of two organic solvents, acetone and dichloromethane, that are normally used for spiking of soil with polycyclic aromatic hydrocarbons for experimental purposes. The solvents were applied in two contamination protocols to either...... higher than in control soil, probably due mainly to release of predation from indigenous protozoa. In order to minimize solvent effects on indigenous soil microorganisms when spiking native soil samples with compounds having a low water solubility, we propose a common protocol in which the contaminant...... tagged with luxAB::Tn5. For both solvents, application to the whole sample resulted in severe side effects on both indigenous protozoa and bacteria. Application of dichloromethane to the whole soil volume immediately reduced the number of protozoa to below the detection limit. In one of the soils...

Critical evaluation of distillation procedure for the determination of methylmercury in soil samples.

Science.gov (United States)

Perez, Pablo A; Hintelman, Holger; Quiroz, Waldo; Bravo, Manuel A

2017-11-01

In the present work, the efficiency of distillation process for extracting monomethylmercury (MMHg) from soil samples was studied and optimized using an experimental design methodology. The influence of soil composition on MMHg extraction was evaluated by testing of four soil samples with different geochemical characteristics. Optimization suggested that the acid concentration and the duration of the distillation process were most significant and the most favorable conditions, established as a compromise for the studied soils, were determined to be a 70 min distillation using an 0.2 M acid. Corresponding limits of detection (LOD) and quantification (LOQ) were 0.21 and 0.7 pg absolute, respectively. The optimized methodology was applied with satisfactory results to soil samples and was compared to a reference methodology based on isotopic dilution analysis followed by gas chromatography-inductively coupled plasma mass spectrometry (IDA-GC-ICP-MS). Using the optimized conditions, recoveries ranged from 82 to 98%, which is an increase of 9-34% relative to the previously used standard operating procedure. Finally, the validated methodology was applied to quantify MMHg in soils collected from different sites impacted by coal fired power plants in the north-central zone of Chile, measuring MMHg concentrations ranging from 0.091 to 2.8 ng g -1 . These data are to the best of our knowledge the first MMHg measurements reported for Chile. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of the grain size of the soil on the measured activity and variation in activity in surface and subsurface soil samples

International Nuclear Information System (INIS)

Sulaiti, H.A.; Rega, P.H.; Bradley, D.; Dahan, N.A.; Mugren, K.A.; Dosari, M.A.

2014-01-01

soil samples (0-5 cm) and 129+-7 to 299+-14 Bq/kg, in the subsurface soil samples (5-25 cm). The activity concentrations of 238U series, 232Th series and 4 degree K in the surface and deep soil samples are approximately same. The 137CS activity concentration levels in surface soil samples in four sites were found to be higher than those observed for the soil samples that been collected at a depth of 5-25 cm. They ranged from 1.65+-0.22 to 19.0:1:0.9 ijq/kg, in the surface soil samples (0-5 cm) and 0.5+-0.2 to 15.4+-0.7 Bq/kg, in the subsurface soil samples (5-25 cm). (author)

Tree Sampling as a Method to Assess Vapor Intrusion Potential at a Site Characterized by VOC-Contaminated Groundwater and Soil.

Science.gov (United States)

Wilson, Jordan L; Limmer, Matthew A; Samaranayake, V A; Schumacher, John G; Burken, Joel G

2017-09-19

Vapor intrusion (VI) by volatile organic compounds (VOCs) in the built environment presents a threat to human health. Traditional VI assessments are often time-, cost-, and labor-intensive; whereas traditional subsurface methods sample a relatively small volume in the subsurface and are difficult to collect within and near structures. Trees could provide a similar subsurface sample where roots act as the "sampler' and are already onsite. Regression models were developed to assess the relation between PCE concentrations in over 500 tree-core samples with PCE concentrations in over 50 groundwater and 1000 soil samples collected from a tetrachloroethylene- (PCE-) contaminated Superfund site and analyzed using gas chromatography. Results indicate that in planta concentrations are significantly and positively related to PCE concentrations in groundwater samples collected at depths less than 20 m (adjusted R 2 values greater than 0.80) and in soil samples (adjusted R 2 values greater than 0.90). Results indicate that a 30 cm diameter tree characterizes soil concentrations at depths less than 6 m over an area of 700-1600 m 2 , the volume of a typical basement. These findings indicate that tree sampling may be an appropriate method to detect contamination at shallow depths at sites with VI.

Tree sampling as a method to assess vapor intrusion potential at a site characterized by VOC-contaminated groundwater and soil

Science.gov (United States)

Wilson, Jordan L.; Limmer, Matthew A.; Samaranayake, V. A.; Schumacher, John G.; Burken, Joel G.

2017-01-01

Vapor intrusion (VI) by volatile organic compounds (VOCs) in the built environment presents a threat to human health. Traditional VI assessments are often time-, cost-, and labor-intensive; whereas traditional subsurface methods sample a relatively small volume in the subsurface and are difficult to collect within and near structures. Trees could provide a similar subsurface sample where roots act as the “sampler’ and are already onsite. Regression models were developed to assess the relation between PCE concentrations in over 500 tree-core samples with PCE concentrations in over 50 groundwater and 1000 soil samples collected from a tetrachloroethylene- (PCE-) contaminated Superfund site and analyzed using gas chromatography. Results indicate that in planta concentrations are significantly and positively related to PCE concentrations in groundwater samples collected at depths less than 20 m (adjusted R2 values greater than 0.80) and in soil samples (adjusted R2 values greater than 0.90). Results indicate that a 30 cm diameter tree characterizes soil concentrations at depths less than 6 m over an area of 700–1600 m2, the volume of a typical basement. These findings indicate that tree sampling may be an appropriate method to detect contamination at shallow depths at sites with VI.

Using Environmental Variables for Studying of the Quality of Sampling in Soil Mapping

Directory of Open Access Journals (Sweden)

A. Jafari

2016-02-01

profiles, which were then described, sampled, analyzed and classified according to the USDA soil classification system (16. The basic rationale is to set up a hypercube, the axes of which are the quantiles of rasters of environmental covariates, e.g., digital elevation model. Sampling evaluation was made using the HELS algorithm. This algorithm was written based on the study of Carre et al., 2007 (3 and run in R. Results and Discussion: The covariate dataset is represented by elevation, slope and wetness index (Table 2. All data layers were interpolated to a common grid of 30 m resolution. The size of the raster layer is 421 by 711 grid cells. Each of the three covariates is divided into four quantiles (Table 2. The hypercube character space has 43, i.e. 64 strata (Figure 5. The average number of grid cells within each stratum is therefore 4677 grid cells. The map of the covariate index (Figure 6 shows some patterns representative of the covariate variability. The values of the covariate index range between 0.0045 and 5.95. This means that some strata are very dense compared to others. This index allows us to explain if high or low relative weight of the sampling units (see below is due to soil sampling or covariate density. The strata with the highest density are in the areas with high geomorphology diversity. It means that geomorphology processes can cause the diversity and variability and it is in line with the geomorphology map (Figure 2. Of the 64 strata, 30.4% represent under-sampling, 60.2% represent adequate sampling and 9.4% represent over-sampling. Regarding the covariate index, most of the under-sampling appears in the high covariate index, where soil covariates are then highly variable. Actually, it is difficult to collect field samples in these highly variable areas (Figure 7. Also, most of the over-sampling was observed in areas with alow covariate index (Figure 7. We calculated the weights of all the sampling units and showed the results in Figure 8. One 64

Sampling of soils for transuranic nuclides: a review

International Nuclear Information System (INIS)

Fowler, E.B.; Essington, E.H.

1977-01-01

A review of the literature pertinent to the sampling of soils for radionuclides is presented; emphasis is placed on transuranic nuclides. Sampling of soils is discussed relative to systems of heterogeneous distributions and varied particle sizes encountered in certain environments. Sampling methods that have been used for two different sources of contamination, global fallout, and accidental or operational releases, are included

Heavy metal accumulation in soils, plants, and hair samples: an assessment of heavy metal exposure risks from the consumption of vegetables grown on soils previously irrigated with wastewater.

Science.gov (United States)

Massaquoi, Lamin Daddy; Ma, Hui; Liu, Xue Hui; Han, Peng Yu; Zuo, Shu-Mei; Hua, Zhong-Xian; Liu, Dian-Wu

2015-12-01

It is common knowledge that soils irrigated with wastewater accumulate heavy metals more than those irrigated with cleaner water sources. However, little is known on metal concentrations in soils and cultivars after the cessation of wastewater use. This study assessed the accumulation and health risk of heavy metals 3 years post-wastewater irrigation in soils, vegetables, and farmers' hair. Soils, vegetables, and hair samples were collected from villages previously irrigating with wastewater (experimental villages) and villages with no history of wastewater irrigation (control villages). Soil samples were digested in a mixture of HCL/HNO3/HCLO4/HF. Plants and hair samples were digested in HNO3/HCLO4 mixture. Inductive coupled plasma-optical emission spectrometer (ICP-OES) was used to determine metal concentrations of digested extracts. Study results indicate a persistence of heavy metal concentration in soils and plants from farms previously irrigated with wastewater. In addition, soils previously irrigated with wastewater were severely contaminated with cadmium. Hair metal concentrations of farmers previously irrigating with wastewater were significantly higher (P metal concentrations in hair samples of farmers previously irrigating with wastewater were not associated with current soil metal concentrations. The study concludes that there is a persistence of heavy metals in soils and plants previously irrigated with wastewater, but high metal concentrations in hair samples of farmers cannot be associated with current soil metal concentrations.

Amostragem para avaliação da fertilidade do solo em função do instrumento de coleta das amostras e de tipos de preparo do solo Sampling for soil fertility evaluation as influenced by sampling tool and soil tillage

Directory of Open Access Journals (Sweden)

Fábio Henrique Tavares de Oliveira

2007-10-01

instrumentos de coleta, a ordem decrescente de variabilidade foi: P > Mg2+ > K+ > Ca2+ > MO > pH. A fertilidade média de uma parcela sob PD ou sob PC após a colheita e antes do preparo do solo subseqüente pode ser avaliada com trado de caneca, em substituição à pá de corte, desde que na preparação da amostra composta de solo 17 % das amostras simples sejam coletadas no sulco de plantio, 33 % a 10 cm do sulco e 50 % no ponto médio entre os sulcos. A fertilidade média de uma parcela sob PD ou PC depois da colheita e antes do preparo do solo subseqüente, avaliada pela análise química da amostra composta, é semelhante àquela avaliada pela média aritmética dos resultados das análises químicas das amostras simples coletadas com pá de corte ou com trado de caneca de forma dirigida. Em geral, a coleta de pelo menos oito amostras simples de solo realizada com pá de corte ou trado de caneca de forma dirigida, conforme utilizado neste trabalho, seria suficiente para formar uma amostra composta representativa para avaliação da fertilidade do solo de uma unidade de amostragem aparentemente homogênea. Entretanto, quanto maior o número de amostras simples coletadas, maior será a confiabilidade ou exatidão da estimativa dessa fertilidade média.The measures of the average and variability of soil fertility indexes can vary with the sampling tool and soil tillage type. Soil sampling methods must be developed that are more reliable to represent the real conditions of soil fertility. This study aimed at an evaluation of the effects of the cutting shovel and hand auger on measures of average and variability of the soil fertility index (a under no-tillage (NT and conventional tillage (CT, (b to estimate the minimum number of simple samples to form a composite sample and (c to test the hypothesis that the arithmetic average of simple samples is equal to the result of the chemical analysis of the composite sample. Chromic Luvisol samples were collected in a control

In situ sampling of small volumes of soil solution using modified micro-suction cups

NARCIS (Netherlands)

Shen, Jianbo; Hoffland, E.

2007-01-01

Two modified designs of micro-pore-water samplers were tested for their capacity to collect unbiased soil solution samples containing zinc and citrate. The samplers had either ceramic or polyethersulfone (PES) suction cups. Laboratory tests of the micro-samplers were conducted using (a) standard

Quality evaluation of processed clay soil samples.

Science.gov (United States)

Steiner-Asiedu, Matilda; Harrison, Obed Akwaa; Vuvor, Frederick; Tano-Debrah, Kwaku

2016-01-01

This study assessed the microbial quality of clay samples sold on two of the major Ghanaian markets. The study was a cross-sectional assessing the evaluation of processed clay and effects it has on the nutrition of the consumers in the political capital town of Ghana. The items for the examination was processed clay soil samples. Staphylococcus spp and fecal coliforms including Klebsiella, Escherichia, and Shigella and Enterobacterspp were isolated from the clay samples. Samples from the Kaneshie market in Accra recorded the highest total viable counts 6.5 Log cfu/g and Staphylococcal count 5.8 Log cfu/g. For fecal coliforms, Madina market samples had the highest count 6.5 Log cfu/g and also recorded the highest levels of yeast and mould. For Koforidua, total viable count was highest in the samples from the Zongo market 6.3 Log cfu/g. Central market samples had the highest count of fecal coliforms 4.6 Log cfu/g and yeasts and moulds 6.5 Log cfu/g. "Small" market recorded the highest staphylococcal count 6.2 Log cfu/g. The water activity of the clay samples were low, and ranged between 0.65±0.01 and 0.66±0.00 for samples collected from Koforidua and Accra respectively. The clay samples were found to contain Klebsiella spp. Escherichia, Enterobacter, Shigella spp. staphylococcus spp., yeast and mould. These have health implications when consumed.

Determining photon energy absorption parameters for different soil samples

International Nuclear Information System (INIS)

Kucuk, Nil; Cakir, Merve; Tumsavas, Zeynal

2013-01-01

The mass attenuation coefficients (μ s ) for five different soil samples were measured at 661.6, 1173.2 and 1332.5 keV photon energies. The soil samples were separately irradiated with 137 Cs and 60 Co (370 kBq) radioactive point gamma sources. The measurements were made by performing transmission experiments with a 2″ x 2″ NaI(Tl) scintillation detector, which had an energy resolution of 7% at 0.662 MeV for the gamma-rays from the decay of 137 Cs. The effective atomic numbers (Z eff ) and the effective electron densities (N eff ) were determined experimentally and theoretically using the obtained μ s values for the soil samples. Furthermore, the Z eff and N eff values of the soil samples were computed for the total photon interaction cross-sections using theoretical data over a wide energy region ranging from 1 keV to 15 MeV. The experimental values of the soils were found to be in good agreement with the theoretical values. Sandy loam and sandy clay loam soils demonstrated poor photon energy absorption characteristics. However, clay loam and clay soils had good photon energy absorption characteristics. (author)

Shrinkage Module of Soil Samples with Different Cement Content

Directory of Open Access Journals (Sweden)

Mohannad Sabry

2017-12-01

Full Text Available The differences in soil's body mass during shrinkage over time have changes in soil physical properties which provide an important reason to check the design of underground foundations in expansive soils. In this paper, a state-of-art of the soil heat stress-strain relationship prediction methods is checked using soil engineering laboratory experiments and Matlab R2013b numerical modelling. The shrinkage of soils with different cement content of (0%, 2%, 4%, 6% and 8% with the same water content of 20 percent in room temperature for 24 hours, are critically reviewed in terms of their predictive shrinkage along with their strengths and flexural behaviour. The review highlights the prediction methods present to determine the effect of heat stress on the shrinkage of soil samples with different cement content after classifying the soils into clay, silt and sand depending on their particle size using sieve and hydrometer experiments. The results of the soil engineering laboratory experiments showed that as the cement content increases, the shrinkage of soil decreases as a result of increased elasticity in soil. The numerical analysis using finite element method in Matlab R2013b shows that as the cement content increases the displacement in the soil sample decreases and that the soil sample with 8% cement content has more resistance to shrinkage and less displacement than the soil with 6% cement, which has less resistance to heat stresses and more displacement.

Area G perimeter surface-soil and single-stage water sampling: Environmental surveillance for fiscal year 1993

International Nuclear Information System (INIS)

Conrad, R.; Childs, M.; Rivera-Dirks, C.; Coriz, F.

1995-07-01

Area G, in Technical Area 54, has been the principle facility at Los Alamos National Laboratory for the storage and disposal of low-level and transuranic (TRU) radioactive wastes since 1957. The current environmental investigation consisted of ESH-19 personnel who collected soil and single-stage water samples around the perimeter of Area G to characterize possible contaminant movement through surface-water runoff. These samples were analyzed for tritium, total uranium, isotopic plutonium, americium-241 (soil only), and cesium 137. The metals, mercury, lead, and barium, were analyzed using x-ray fluorescence

Soil sampling and analytical strategies for mapping fallout in nuclear emergencies based on the Fukushima Dai-ichi Nuclear Power Plant accident

International Nuclear Information System (INIS)

Onda, Yuichi; Kato, Hiroaki; Hoshi, Masaharu; Takahashi, Yoshio; Nguyen, Minh-Long

2015-01-01

The Fukushima Dai-ichi Nuclear Power Plant (FDNPP) accident resulted in extensive radioactive contamination of the environment via deposited radionuclides such as radiocesium and 131 I. Evaluating the extent and level of environmental contamination is critical to protecting citizens in affected areas and to planning decontamination efforts. However, a standardized soil sampling protocol is needed in such emergencies to facilitate the collection of large, tractable samples for measuring gamma-emitting radionuclides. In this study, we developed an emergency soil sampling protocol based on preliminary sampling from the FDNPP accident-affected area. We also present the results of a preliminary experiment aimed to evaluate the influence of various procedures (e.g., mixing, number of samples) on measured radioactivity. Results show that sample mixing strongly affects measured radioactivity in soil samples. Furthermore, for homogenization, shaking the plastic sample container at least 150 times or disaggregating soil by hand-rolling in a disposable plastic bag is required. Finally, we determined that five soil samples within a 3 m × 3-m area are the minimum number required for reducing measurement uncertainty in the emergency soil sampling protocol proposed here. - Highlights: • Emergency soil sampling protocol was proposed for nuclear hazards. • Various sampling procedures were tested and evaluated in Fukushima area. • Soil sample mixing procedure was of key importance for measured radioactivity. • Minimum number of sampling was determined for reducing measurement uncertainty

Regional soil erosion assessment based on a sample survey and geostatistics

Science.gov (United States)

Yin, Shuiqing; Zhu, Zhengyuan; Wang, Li; Liu, Baoyuan; Xie, Yun; Wang, Guannan; Li, Yishan

2018-03-01

Soil erosion is one of the most significant environmental problems in China. From 2010 to 2012, the fourth national census for soil erosion sampled 32 364 PSUs (Primary Sampling Units, small watersheds) with the areas of 0.2-3 km2. Land use and soil erosion controlling factors including rainfall erosivity, soil erodibility, slope length, slope steepness, biological practice, engineering practice, and tillage practice for the PSUs were surveyed, and the soil loss rate for each land use in the PSUs was estimated using an empirical model, the Chinese Soil Loss Equation (CSLE). Though the information collected from the sample units can be aggregated to estimate soil erosion conditions on a large scale; the problem of estimating soil erosion condition on a regional scale has not been addressed well. The aim of this study is to introduce a new model-based regional soil erosion assessment method combining a sample survey and geostatistics. We compared seven spatial interpolation models based on the bivariate penalized spline over triangulation (BPST) method to generate a regional soil erosion assessment from the PSUs. Shaanxi Province (3116 PSUs) in China was selected for the comparison and assessment as it is one of the areas with the most serious erosion problem. Ten-fold cross-validation based on the PSU data showed the model assisted by the land use, rainfall erosivity factor (R), soil erodibility factor (K), slope steepness factor (S), and slope length factor (L) derived from a 1 : 10 000 topography map is the best one, with the model efficiency coefficient (ME) being 0.75 and the MSE being 55.8 % of that for the model assisted by the land use alone. Among four erosion factors as the covariates, the S factor contributed the most information, followed by K and L factors, and R factor made almost no contribution to the spatial estimation of soil loss. The LS factor derived from 30 or 90 m Shuttle Radar Topography Mission (SRTM) digital elevation model (DEM) data

Advanced Soil Moisture Network Technologies; Developments in Collecting in situ Measurements for Remote Sensing Missions

Science.gov (United States)

Moghaddam, M.; Silva, A. R. D.; Akbar, R.; Clewley, D.

2015-12-01

The Soil moisture Sensing Controller And oPtimal Estimator (SoilSCAPE) wireless sensor network has been developed to support Calibration and Validation activities (Cal/Val) for large scale soil moisture remote sensing missions (SMAP and AirMOSS). The technology developed here also readily supports small scale hydrological studies by providing sub-kilometer widespread soil moisture observations. An extensive collection of semi-sparse sensor clusters deployed throughout north-central California and southern Arizona provide near real time soil moisture measurements. Such a wireless network architecture, compared to conventional single points measurement profiles, allows for significant and expanded soil moisture sampling. The work presented here aims at discussing and highlighting novel and new technology developments which increase in situ soil moisture measurements' accuracy, reliability, and robustness with reduced data delivery latency. High efficiency and low maintenance custom hardware have been developed and in-field performance has been demonstrated for a period of three years. The SoilSCAPE technology incorporates (a) intelligent sensing to prevent erroneous measurement reporting, (b) on-board short term memory for data redundancy, (c) adaptive scheduling and sampling capabilities to enhance energy efficiency. A rapid streamlined data delivery architecture openly provides distribution of in situ measurements to SMAP and AirMOSS cal/val activities and other interested parties.

Distribution of pesticide residues in soil and uncertainty of sampling.

Science.gov (United States)

Suszter, Gabriela K; Ambrus, Árpád

2017-08-03

Pesticide residues were determined in about 120 soil cores taken randomly from the top 15 cm layer of two sunflower fields about 30 days after preemergence herbicide treatments. Samples were extracted with acetone-ethyl acetate mixture and the residues were determined with GC-TSD. Residues of dimethenamid, pendimethalin, and prometryn ranged from 0.005 to 2.97 mg/kg. Their relative standard deviations (CV) were between 0.66 and 1.13. The relative frequency distributions of residues in soil cores were very similar to those observed in root and tuber vegetables grown in pesticide treated soils. Based on all available information, a typical CV of 1.00 was estimated for pesticide residues in primary soil samples (soil cores). The corresponding expectable relative uncertainty of sampling is 20% when composite samples of size 25 are taken. To obtain a reliable estimate of the average residues in the top 15 cm layer of soil of a field up to 8 independent replicate random samples should be taken. To obtain better estimate of the actual residue level of the sampled filed would be marginal if larger number of samples were taken.

105-DR Large sodium fire facility soil sampling data evaluation report

International Nuclear Information System (INIS)

Adler, J.G.

1996-01-01

This report evaluates the soil sampling activities, soil sample analysis, and soil sample data associated with the closure activities at the 105-DR Large Sodium Fire Facility. The evaluation compares these activities to the regulatory requirements for meeting clean closure. The report concludes that there is no soil contamination from the waste treatment activities

Area G perimeter surface-soil and single-stage water sampling: Environmental surveillance for fiscal year 94, Group ESH-19. Progress report

International Nuclear Information System (INIS)

Conrad, R.; Childs, M.; Lyons, C.R.; Coriz, F.

1996-08-01

ESH-19 personnel collected soil and single-stage water samples around the perimeter of Area G at Los Alamos National Laboratory during FY94 to characterize possible contaminant movement out of Area G through surface-water and sediment runoff. These samples were analyzed for tritium, total uranium, isotopic plutonium, americium-241, and cesium-137. Ten metals were also analyzed on selected soils using analytical laboratory techniques. All radiochemical data are compared with analogous samples collected during FY 93 and reported in LA-12986. Baseline concentrations for future disposal operations were established for metals and radionuclides by a sampling program in the proposed Area G Expansion Area. Considering the amount of radioactive waste that has been disposed at Area G, there is evidence of only low concentrations of radionuclides on perimeter surface soils. Consequently, little radioactivity is leaving the confines of Area G via the surface water runoff pathway

Vertical distribution and environmental significance of sulfur and oxygen heterocyclic aromatic hydrocarbons in soil samples collected from Beijing, China

International Nuclear Information System (INIS)

Zhang Zhihuan; He Fengpeng; Bu Qingwei; Lu Song

2008-01-01

Vertical distribution of the concentration and composition of some sulfur and oxygen heterocyclic aromatic hydrocarbons (SOHAHs), such as, fluorene, dibenzofuran, dibenzothiophene and their alkyl homologues in 10 soil profiles in Beijing have been investigated. The results showed that the concentrations and composition of SOHAHs in topsoil (0-30 cm) from different profiles are different. The concentrations of SOHAHs in topsoils are much higher than that in bottom soils where the concentrations are relatively constant. The fingerprints of SOHAHs from same profile are similar in topsoil samples, which are obviously different at the deep part, which suggested that the sources of these compounds are consistent in topsoil and are discriminating between surface and bottom soils. The main sources of SOHAHs in surface soil were fossil fuel combustion, petroleum and wastewater irrigation, while those at deep part were likely derived from the degradation products of soil organic matters. - The vertical distribution of SOHAHs was provided and possible sources were different between topsoils and deep part

Sampling design for use by the soil decontamination project

International Nuclear Information System (INIS)

Rutherford, D.W.; Stevens, J.R.

1981-01-01

This report proposes a general approach to the problem and discusses sampling of soil to map the contaminated area and to provide samples for characterizaton of soil components and contamination. Basic concepts in sample design are reviewed with reference to environmental transuranic studies. Common designs are reviewed and evaluated for use with specific objectives that might be required by the soil decontamination project. Examples of a hierarchial design pilot study and a combined hierarchial and grid study are proposed for the Rocky Flats 903 pad area

Radium and radon exhalation rate in soil samples of Hassan district of South Karnataka, India

International Nuclear Information System (INIS)

Jagadeesha, B.G.; Narayana, Y.

2016-01-01

The radon exhalation rate was measured in 32 soil samples collected from Hassan district of South Karnataka. Radon exhalation rate of soil samples was measured using can technique. The results show variation of radon exhalation rate with radium content of the soil samples. A strong correlation was observed between effective radium content and radon exhalation rate. In the present work, an attempt was made to assess the levels of radon in the environment of Hassan. Radon activities were found to vary from 2.25±0.55 to 270.85±19.16 Bq m"-"3 and effective radium contents vary from 12.06±2.98 to 1449.56±102.58 mBq kg"-"1. Surface exhalation rates of radon vary from 1.55±0.47 to 186.43±18.57 mBq m"-"2 h"-"1, and mass exhalation rates of radon vary from 0.312±0.07 to 37.46±2.65 mBq kg"-"1 h"-"1. (authors)

Radioactivity Levels And Gamma Dose Rate In Soil Samples From Federation Of Bosnia And Herzegovina

International Nuclear Information System (INIS)

Deljkic, D.; Kadic, I.; Ilic, Z.; Vidic, A.

2015-01-01

Activity concentrations of 226Ra, 232Th, 40K and 137Cs in soil samples collected from different regions of Federation of Bosnia and Herzegovina have been measured by gamma-ray spectrometry. The measured activity concentrations for these radionuclides are compared with the reported data from different other countries and it is found that measured activity concentrations are comparable with the worldwide measured average values reported by the UNSCEAR. Experimental results were obtained by using a high-purity germanium (HPGe) detector and gamma - ray spectrometry analysis system at Institute for Public Health FBiH (Radiation Protection Center). The measuring time of all soil samples was 86000 seconds. It was found that the soil specific activity ranges from 24.59 to 161.20 Bq/kg for 226Ra, from 17.60 to 66.45 Bq/kg for 232Th, from 179.50 to 598.04 Bq kg-1 for 40K and from 11.13 to 108.69 Bq/kg for 137Cs with the mean values of 62.34; 46.97; 392.76 and 51.49 Bq/kg, respectively. The radium equivalent activity in all the soil samples is lower than the safe limit (370 Bq/kg), ranges from 63.58 to 287.03 Bq/kg with the mean value of 159.71 Bq/kg. Man-made radionuclide 137Cs is also present in detectable amount in all soil samples. Presence of 137Cs indicates that the samples in this area also receive some fallout from nuclear accident in Chernobyl power plant in 1986. The value of external radiation hazard indices is found to be less than unity (mean value of 0.43). Absorbed dose rates and effective dose equivalents are also determined for the samples. The concentration of radionuclides found in the soil samples during the present study does not pose any potential health hazard to the general public. (author).

Sampling for Soil Carbon Stock Assessment in Rocky Agricultural Soils

Science.gov (United States)

Beem-Miller, Jeffrey P.; Kong, Angela Y. Y.; Ogle, Stephen; Wolfe, David

2016-01-01

Coring methods commonly employed in soil organic C (SOC) stock assessment may not accurately capture soil rock fragment (RF) content or soil bulk density (rho (sub b)) in rocky agricultural soils, potentially biasing SOC stock estimates. Quantitative pits are considered less biased than coring methods but are invasive and often cost-prohibitive. We compared fixed-depth and mass-based estimates of SOC stocks (0.3-meters depth) for hammer, hydraulic push, and rotary coring methods relative to quantitative pits at four agricultural sites ranging in RF content from less than 0.01 to 0.24 cubic meters per cubic meter. Sampling costs were also compared. Coring methods significantly underestimated RF content at all rocky sites, but significant differences (p is less than 0.05) in SOC stocks between pits and corers were only found with the hammer method using the fixed-depth approach at the less than 0.01 cubic meters per cubic meter RF site (pit, 5.80 kilograms C per square meter; hammer, 4.74 kilograms C per square meter) and at the 0.14 cubic meters per cubic meter RF site (pit, 8.81 kilograms C per square meter; hammer, 6.71 kilograms C per square meter). The hammer corer also underestimated rho (sub b) at all sites as did the hydraulic push corer at the 0.21 cubic meters per cubic meter RF site. No significant differences in mass-based SOC stock estimates were observed between pits and corers. Our results indicate that (i) calculating SOC stocks on a mass basis can overcome biases in RF and rho (sub b) estimates introduced by sampling equipment and (ii) a quantitative pit is the optimal sampling method for establishing reference soil masses, followed by rotary and then hydraulic push corers.

Analysis of large soil samples for actinides

Science.gov (United States)

Maxwell, III; Sherrod, L [Aiken, SC

2009-03-24

A method of analyzing relatively large soil samples for actinides by employing a separation process that includes cerium fluoride precipitation for removing the soil matrix and precipitates plutonium, americium, and curium with cerium and hydrofluoric acid followed by separating these actinides using chromatography cartridges.

The Impact of Including Below Detection Limit Samples in Post Decommissioning Soil Sample Analyses

Energy Technology Data Exchange (ETDEWEB)

Kim, Jung Hwan; Yim, Man-Sung [KAIST, Daejeon (Korea, Republic of)

2016-10-15

To meet the required standards the site owner has to show that the soil at the facility has been sufficiently cleaned up. To do this one must know the contamination of the soil at the site prior to clean up. This involves sampling that soil to identify the degree of contamination. However there is a technical difficulty in determining how much decontamination should be done. The problem arises when measured samples are below the detection limit. Regulatory guidelines for site reuse after decommissioning are commonly challenged because the majority of the activity in the soil at or below the limit of detection. Using additional statistical analyses of contaminated soil after decommissioning is expected to have the following advantages: a better and more reliable probabilistic exposure assessment, better economics (lower project costs) and improved communication with the public. This research will develop an approach that defines an acceptable method for demonstrating compliance of decommissioned NPP sites and validates that compliance. Soil samples from NPP often contain censored data. Conventional methods for dealing with censored data sets are statistically biased and limited in their usefulness. In this research, additional methods are performed using real data from a monazite manufacturing factory.

SEAMIST trademark soil sampling for tritiated water: First year's results

International Nuclear Information System (INIS)

Mallon, B.; Martins, S.A.; Houpis, J.L.; Lowry, W.; Cremer, C.D.

1992-01-01

SEAMIST trademark is a recently developed sampling system that enables one to measure various soil parameters by means of an inverted, removable, impermeable membrane tube inserted in a borehole. This membrane tube can have various measuring devices installed on it, such as gas ports, adsorbent pads, and electrical sensors. These membrane tubes are made of a laminated polymer. The Lawrence Livermore National Laboratory in Livermore, California, has installed two of these systems to monitor tritium in soil resulting from a leak in an underground storage tank. One tube is equipped with gas ports to sample soil vapor and the other with adsorbent pads to sample soil moisture. Borehole stability was maintained using either sand-filled or air-inflated tubes. Both system implementations yielded concentrations or activities that compared well with the measured concentrations of tritium in the soil taken during borehole construction. In addition, an analysis of the data suggest that both systems prevented the vertical migration of tritium in the boreholes. Also, a neutron probe was successfully used in a blank membrane inserted in one of the boreholes to monitor the moisture in the soil without exposing the probe to the tritium. The neutron log showed excellent agreement with the soil moisture content measured in soil samples taken during borehole construction. This paper describes the two SEAMIST trademark systems used and presents sampling results and comparisons

Amostragem de solo para estudos de fertilidade Sampling soils for fertility studies

Directory of Open Access Journals (Sweden)

R. A. Catani

1955-01-01

Full Text Available O presente trabalho foi realizado com a finalidade de estabelecer um sistema e técnica mais adequados de se coletar amostras de terra, para fins de estudo de fertilidade. Foram escolhidas duas áreas de solos diferentes. Uma delas com seis hectares, situada na Estação Experimental de Ribeirão Prêto, em solo tipo terra roxa legítima ; a outra com quatro hectares e localizada na Fazenda Santa Maria, em Pindorama, em solo do tipo arenito Bauru. A retirada das amostras de cada área foi feita com tubos especialmente construídos para esse fim e obedeceu ao seguinte critério: 1 30 amostras simples, cobrindo tôda a área ; 2 10 amostras compostas, formadas de cinco amostras simples, cobrindo tôda a área. 3 5 amostras compostas, formadas de 20 amostras simples, cobrindo tôda a área. Nessas amostras foram determinados : pH, carbono total, potássio "trocável" e cálcio "trocável". Diante dos dados obtidos e levando-se em conta o trabalho exigido no laboratório, aconselha-se a retirada de três amostras compostas formadas de 20 simples cada uma, em glebas uniformes, de cinco hectares aproximadamente.The following methods of collecting soil samples for fertility studies were compared : 1 thirty individual samples covering the whole area ; 2 ten composite samples, each consisting of five individual samples, covering the whole area ; 3 five composite samples, each consisting of 20 individual samples, covering the whole area. The three types of samples were collected in each of two plots : 1 a six-hectare plot in the Estação Experimental de Ribeirão Prêto, representing the "terra roxa" soil; 2 a four-hectare plot in the Santa Maria Farm, Pindorama, where the soil is of the "arenito de Bauru" type. The pH, total carbon, and exchangeable potassium and calcium were determined in the samples. Based on data obtained in the present investigation and considering the amount of work involved in the routine laboratory tests, it is suggested that

Major and minor elements analysis in soil samples by neutron activation analysis and X-ray fluorescence

International Nuclear Information System (INIS)

Morcelli, Claudia Petronilho Ribeiro; Ana Maria Graciano; Enzweiler, Jacinta

2002-01-01

In the present work, Instrumental Neutron Activation Analysis (INAA) and X-Ray Fluorescence were employed to analyze major and minor elements in soil samples collected near Bandeirantes road. Elements of environmental interest, such as Al, Sb, As, Ba, Cd, Pb, Co, Cu, Cr, Fe, Mn, Mo, Ni, Se, V and Zn, which have reference background levels, were determined. The samples were dried in an oven at 40 deg C, were sieved (<2 mm), grinded and were analyzed by INAA and FRX. The aims of this work were: to evaluate the possible variations in the concentration levels in soil due to emission of particulate from vehicles and other anthropogenic sources; to compare the results obtained by using both techniques. This preliminary study showed that the concentration levels of the elements of environmental interest agree with reference values for tropical soils in the sampling sites, except for Ba, which presented higher values. (author)

Sample collection: an overview of the Hydrogeochemical and Stream Sediment Reconnaissance Program

International Nuclear Information System (INIS)

Bolivar, S.L.

1979-01-01

A Hydrogeochemical and Stream Sediment Reconnaissance (HSSR) for uranium is currently being conducted throughout the conterminous United States and Alaska. The HSSR is part of the National Uranium Resource Evaluation sponsored by the US Department of Energy. This ambitious geochemical reconnaissance program is conducted by four national laboratories: Los Alamos Scientific Laboratory, Lawrence Livermore Laboratory, Oak Ridge Gaseous Diffusion Plant, and Savannah River Laboratory. The program is based on an extensive review of world literature, reconnaissance work done in other countries, and pilot studies conducted by each laboratory. Sample-collection methods and sample density are determined to optimize the probability of detecting potential uranium mineralization. To achieve this aim, each laboratory has developed independent standardized field collection procedures that are designed for its section of the country. Field parameters such as pH, conductivity, climate, geography, and geology are recorded at each site. Most samples are collected at densities of one sample site per 10 to 23 km 2 . The HSSR program has helped to improve existing hydrogeochemical reconnaissance exploration techniques. In addition to providing industry with data that may help to identify potential uranium districts and to extend known uranium provinces, the HSSR also provides multi-element analytical data, which can be used in water quality, soil, sediment, environmental, and base-metal exploration studies

Natural radioactivity in soil samples of Kocaeli basin, Turkey

International Nuclear Information System (INIS)

Karakelle, B.; Oeztuerk, N.; Erkol, A.Y.; Koese, A.; Varinlioglu, A.; Yilmaz, F.

2002-01-01

The city of Kocaeli is in the western part of Anatolia in Turkey and has a population of approximately 1.000.000. There is no information about radioactivity in the Kocaeli soils samples so far. For this reason, the concentrations of the natural radionuclides in soil samples from 27 different sampling stations in Kocaeli Basin and its surroundings have been determined. The results have been compared with other radioactivity measurements in different country's soils. The typical concentrations of 137 Cs, 238 U, 40 K, 226 Ra, 232 Th found in surface soil samples ranged from 2 ± 0.6 to 25 ± 6 Bq/kg, from 11 ± 4 to 49 ± 10 Bq/kg, from 161 ± 30 to 964 ± 127 Bq/kg, from 10 ± 4 to 58 ± 11 Bq/kg, and from 11 ± 3 to 65 ± 13 Bq/kg, respectively. (author)

Assessment the effect of homogenized soil on soil hydraulic properties and soil water transport

Science.gov (United States)

Mohawesh, O.; Janssen, M.; Maaitah, O.; Lennartz, B.

2017-09-01

Soil hydraulic properties play a crucial role in simulating water flow and contaminant transport. Soil hydraulic properties are commonly measured using homogenized soil samples. However, soil structure has a significant effect on the soil ability to retain and to conduct water, particularly in aggregated soils. In order to determine the effect of soil homogenization on soil hydraulic properties and soil water transport, undisturbed soil samples were carefully collected. Five different soil structures were identified: Angular-blocky, Crumble, Angular-blocky (different soil texture), Granular, and subangular-blocky. The soil hydraulic properties were determined for undisturbed and homogenized soil samples for each soil structure. The soil hydraulic properties were used to model soil water transport using HYDRUS-1D.The homogenized soil samples showed a significant increase in wide pores (wCP) and a decrease in narrow pores (nCP). The wCP increased by 95.6, 141.2, 391.6, 3.9, 261.3%, and nCP decreased by 69.5, 10.5, 33.8, 72.7, and 39.3% for homogenized soil samples compared to undisturbed soil samples. The soil water retention curves exhibited a significant decrease in water holding capacity for homogenized soil samples compared with the undisturbed soil samples. The homogenized soil samples showed also a decrease in soil hydraulic conductivity. The simulated results showed that water movement and distribution were affected by soil homogenizing. Moreover, soil homogenizing affected soil hydraulic properties and soil water transport. However, field studies are being needed to find the effect of these differences on water, chemical, and pollutant transport under several scenarios.

Contamination of Soil Samples of Public Parks with Toxocara spp. Eggs in Kermanshah, Iran

Directory of Open Access Journals (Sweden)

Omid GHASHGHAEI

2016-01-01

Full Text Available Toxocariasis is a zoonotic helminth infection, occurring in humans by the accidental ingestion of embryonated eggs of Toxocara canis and less frequently Toxocara cati. The present study was conducted to determine the existence of Toxocara spp. eggs by using the sucrose flotation method. A total of 150 soil samples were collected randomly from 7 public parks in Kermanshah city between September and December 2014 for investigating the presence of infective stages of parasites and to determine the prevalence of helminth eggs. Of the 150 soil samples examined, 27 (18% were infected with eggs of Toxocara spp. eggs. The present investigation showed that humans (especially children from urban areas are at risk of acquiring helminth infection from contaminated soil. Since this host species is capable of transmitting zoonotic agents to both animals and humans, animal populations, including stray dogs and cats, have to be controlled to minimize the distribution of parasites.

Diversity of microorganisms isolated from the soil sample surround Chroogomphus rutilus in the Beijing region

DEFF Research Database (Denmark)

Wang, P; Liu, Y; Yin, Y

2011-01-01

to isolate and classify beneficial microorganisms that could affect its growth, which could be used in future research on artificial cultivation. In total, 342 isolates were isolated from soil samples collected around a C. rutilus colony in the Beijing region. Of these, 22 bacterial and 14 fungal isolates...

Measurement of natural radioactivity for polonium-210 in water and soil samples from Vythiry Taluk, Wayanad district, Kerala

International Nuclear Information System (INIS)

Athif, P.; Periyasamy, M.; Syed Mohamed, H.E.; Sadiq Bukhari, A.; Shajeer, P.A.; Kogilan, R.; Muzammil, F.S.

2017-01-01

Ground water and soil samples were collected from various tea plantation regions of the Vythiry taluk, Wayanad district, Kerala and measured the "2"1"0Po activity concentration. The descriptive statistical analysis was carried out using SPSS version 16. The higher distribution is observed between water and soil (1.8 mBq/L and 2.8 Bq/Kg) respectively. (author)

Geochemical Data for Samples Collected in 2007 Near the Concealed Pebble Porphyry Cu-Au-Mo Deposit, Southwest Alaska

Science.gov (United States)

Fey, David L.; Granitto, Matthew; Giles, Stuart A.; Smith, Steven M.; Eppinger, Robert G.; Kelley, Karen D.

2008-01-01

relatively subdued topographic relief with an elevation of around 300 m (1000 ft). This portion of Alaska is part of the subarctic regime mountains division, Yukon intermontane plateaus-tayga-meadow province ecoregion, as defined by Bailey (U.S. Forest Service, 2007). Between June 28th and July 12th, 2007, scientists from the USGS collected soil, water, stream sediment, vegetation, heavy-mineral concentrate, till, and rock samples from the deposit area. This report contains analytical results for soil, water, stream sediment, and vegetation samples. Analyses for the heavy-mineral concentrate, till, and rock samples are still in progress. The sampling was undertaken during relatively dry and stable weather conditions. Only minor scattered rain showers occurred during the sampling period, so surface conditions were largely unaffected by weather. The predominant sample media collected were soils and surface waters. Soil and water (mostly from ponds and springs, some from small creeks) samples were collected along a single 7.8 km-long (4.8 mi) east-west traverse across the Pebble East and Pebble West zones and from more distal background areas around Koktuli and Kaskanak Mountains. Sample sites are shown on figure 2 and plate 1, and locality coordinates are provided in the accompanying Access and Excel files named FieldSite. Water samples were analyzed by USGS laboratories with one subset analyzed by Activation Laboratories (Actlabs), as indicated below. Soils and stream sediments were analyzed for their total content by SGS Minerals Services under a contract with the USGS. Soil samples were also leached by selected partial-extraction leaching procedures and then analyzed by several commercial laboratories, as described below. Vegetation samples were analyzed as indicated below.

Sample size choices for XRCT scanning of highly unsaturated soil mixtures

Directory of Open Access Journals (Sweden)

Smith Jonathan C.

2016-01-01

Full Text Available Highly unsaturated soil mixtures (clay, sand and gravel are used as building materials in many parts of the world, and there is increasing interest in understanding their mechanical and hydraulic behaviour. In the laboratory, x-ray computed tomography (XRCT is becoming more widely used to investigate the microstructures of soils, however a crucial issue for such investigations is the choice of sample size, especially concerning the scanning of soil mixtures where there will be a range of particle and void sizes. In this paper we present a discussion (centred around a new set of XRCT scans on sample sizing for scanning of samples comprising soil mixtures, where a balance has to be made between realistic representation of the soil components and the desire for high resolution scanning, We also comment on the appropriateness of differing sample sizes in comparison to sample sizes used for other geotechnical testing. Void size distributions for the samples are presented and from these some hypotheses are made as to the roles of inter- and intra-aggregate voids in the mechanical behaviour of highly unsaturated soils.

Regional soil erosion assessment based on a sample survey and geostatistics

Directory of Open Access Journals (Sweden)

S. Yin

2018-03-01

Full Text Available Soil erosion is one of the most significant environmental problems in China. From 2010 to 2012, the fourth national census for soil erosion sampled 32 364 PSUs (Primary Sampling Units, small watersheds with the areas of 0.2–3 km2. Land use and soil erosion controlling factors including rainfall erosivity, soil erodibility, slope length, slope steepness, biological practice, engineering practice, and tillage practice for the PSUs were surveyed, and the soil loss rate for each land use in the PSUs was estimated using an empirical model, the Chinese Soil Loss Equation (CSLE. Though the information collected from the sample units can be aggregated to estimate soil erosion conditions on a large scale; the problem of estimating soil erosion condition on a regional scale has not been addressed well. The aim of this study is to introduce a new model-based regional soil erosion assessment method combining a sample survey and geostatistics. We compared seven spatial interpolation models based on the bivariate penalized spline over triangulation (BPST method to generate a regional soil erosion assessment from the PSUs. Shaanxi Province (3116 PSUs in China was selected for the comparison and assessment as it is one of the areas with the most serious erosion problem. Ten-fold cross-validation based on the PSU data showed the model assisted by the land use, rainfall erosivity factor (R, soil erodibility factor (K, slope steepness factor (S, and slope length factor (L derived from a 1 : 10 000 topography map is the best one, with the model efficiency coefficient (ME being 0.75 and the MSE being 55.8 % of that for the model assisted by the land use alone. Among four erosion factors as the covariates, the S factor contributed the most information, followed by K and L factors, and R factor made almost no contribution to the spatial estimation of soil loss. The LS factor derived from 30 or 90 m Shuttle Radar Topography Mission

PCR detection of Burkholderia multivorans in water and soil samples.

Science.gov (United States)

Peeters, Charlotte; Daenekindt, Stijn; Vandamme, Peter

2016-08-12

Although semi-selective growth media have been developed for the isolation of Burkholderia cepacia complex bacteria from the environment, thus far Burkholderia multivorans has rarely been isolated from such samples. Because environmental B. multivorans isolates mainly originate from water samples, we hypothesized that water rather than soil is its most likely environmental niche. The aim of the present study was to assess the occurrence of B. multivorans in water samples from Flanders (Belgium) using a fast, culture-independent PCR assay. A nested PCR approach was used to achieve high sensitivity, and specificity was confirmed by sequencing the resulting amplicons. B. multivorans was detected in 11 % of the water samples (n = 112) and 92 % of the soil samples (n = 25) tested. The percentage of false positives was higher for water samples compared to soil samples, showing that the presently available B. multivorans recA primers lack specificity when applied to the analysis of water samples. The results of the present study demonstrate that B. multivorans DNA is commonly present in soil samples and to a lesser extent in water samples in Flanders (Belgium).

Assessment of natural radioactivity and radiation hazard indices in different soil samples from Assiut governorate

International Nuclear Information System (INIS)

Issa, S.A.M.; Uosif, M.A.M.; Hefni, M.A.; El-Kamel, A.H; Nesreen, A.A.

2013-01-01

Natural radioactive materials under certain conditions can reach hazard radiological levels. So, it becomes necessary to study the natural radioactivity levels in soil to assess the dose for the population in order to know the health risks and to have a baseline for future changes in the environmental radioactivity due to human activities. Determine the radioactivity concentration of 226 Ra, 232 Th and 40 K in surface and 20 cm soil samples collected beside Assiut fertilizer plant, Assiut government in south Upper Egypt, to assess their contribution to the external dose exposure. The contents of natural radionuclides 226 Ra, 232 Th and 40 K were measured in investigated samples by using gamma spectrometry [NaI (Tl) 3”x 3”]. The total absorbed dose rate, annual effective dose rate, radium equivalent, excess lifetime cancer risk and the external hazard index, which resulted from the natural radionuclides in soil, were calculated

The Benefits of Sample Return: Connecting Apollo Soils and Diviner Lunar Radiometer Remote Sensing Data

Science.gov (United States)

Greenhagen, B. T.; Donaldson-Hanna, K. L.; Thomas, I. R.; Bowles, N. E.; Allen, C. C.; Pieters, C. M.; Paige, D. A.

2014-01-01

The Diviner Lunar Radiometer, onboard NASA's Lunar Reconnaissance Orbiter, has produced the first global, high resolution, thermal infrared observations of an airless body. The Moon, which is the most accessible member of this most abundant class of solar system objects, is also the only body for which we have extraterrestrial samples with known spatial context. Here we present the results of a comprehensive study to reproduce an accurate simulated lunar environment, evaluate the most appropriate sample and measurement conditions, collect thermal infrared spectra of a representative suite of Apollo soils, and correlate them with Diviner observations of the lunar surface. We find that analyses of Diviner observations of individual sampling stations and SLE measurements of returned Apollo soils show good agreement, while comparisons to thermal infrared reflectance under terrestrial conditions do not agree well, which underscores the need for SLE measurements and validates the Diviner compositional dataset. Future work includes measurement of additional soils in SLE and cross comparisons with measurements in JPL Simulated Airless Body Emission Laboratory (SABEL).

Spatial distribution of metals in soil samples from Zona da Mata, Pernambuco, Brazil using XRF technique

International Nuclear Information System (INIS)

Fernandez, Zahily Herrero; Santos Junior, Jose Araujo dos; Amaral, Romilton dos Santos; Menezes, Romulo Simoes Cezar; Santos, Josineide Marques do Nascimento; Bezerra, Jairo Dias; Damascena, Kennedy Francys Rodrigues; Silva, Edvane Borges da; Silva, Alberto Antonio da

2015-01-01

Soil contamination is today one of the most important environmental issues for society. In the past, soil pollution was not considered as important as air and water contamination, because this was more difficult to be controlled, becoming an important topic in studies of environmental protection worldwide. Based on this, this paper provides information on the determination of metals in soil samples collected in Zona da Mata, Pernambuco, Brazil, where normally the application of pesticides, insecticides and other agricultural additives are used in a disorderly manner and without control. A total of 24 sampling points were monitored. The analysis of Mn, Fe, Ni, Zn, Br, Rb, Sr, Pb, Ti, La, Al, Si and P were performed using Energy Dispersive X-Ray Fluorescence. In order to assess the development of analytical method, inorganic Certified Reference Materials (IAEA-SOIL-7 and SRM 2709) were analyzed. In each sampling site, the geoaccumulation index were calculated to estimate the level of metal contamination in the soil, this was made taking into account the resolution 460 of the National Environmental Council (CONAMA in Portuguese). The elemental distribution patterns obtained for each metal were associated with different pollution sources. This assessment provides an initial description of pollution levels presented by metals in soils from several areas of Zona da Mata, providing quantitative evidence and demonstrating the need to improve the regulation of agricultural and industrial activities. (author)

Spatial distribution of metals in soil samples from Zona da Mata, Pernambuco, Brazil using XRF technique

Energy Technology Data Exchange (ETDEWEB)

Fernandez, Zahily Herrero; Santos Junior, Jose Araujo dos; Amaral, Romilton dos Santos; Menezes, Romulo Simoes Cezar; Santos, Josineide Marques do Nascimento; Bezerra, Jairo Dias; Damascena, Kennedy Francys Rodrigues, E-mail: zahily1985@gmail.com, E-mail: jaraujo@ufpe.br, E-mail: romilton@ufpe.br, E-mail: rmenezes@ufpe.br, E-mail: neideden@hotmail.com, E-mail: jairo.dias@ufpe.br, E-mail: kennedy.eng.ambiental@gmail.com [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Centro de Tecnologia e Geociencias. Departamento de Energia Nuclear; Alvarez, Juan Reinaldo Estevez, E-mail: jestevez@ceaden.cu [Centro de Aplicaciones Tecnologicas y Desarrollo Nuclear (CEADEN), Havana (Cuba); Silva, Edvane Borges da, E-mail: edvane.borges@pq.cnpq.br [Universidade Federal de Pernambuco (UFPE), Vitoria de Santo Antao, PE (Brazil). Nucleo de Biologia; Franca, Elvis Joacir de; Farias, Emerson Emiliano Gualberto de, E-mail: ejfranca@cnen.gov.br, E-mail: emersonemiliano@yahoo.com.br [Centro Regional de Ciencias Nucleares do Nordeste (CRCN-NE/CNEN-PE), Recife, PE (Brazil); Silva, Alberto Antonio da, E-mail: alberto.silva@barreiros.ifpe.edu.br [Instituto Federal de Educacao, Ciencia e Tecnologia de Pernambuco (IFPE), Barreiros, PE (Brazil)

2015-07-01

Soil contamination is today one of the most important environmental issues for society. In the past, soil pollution was not considered as important as air and water contamination, because this was more difficult to be controlled, becoming an important topic in studies of environmental protection worldwide. Based on this, this paper provides information on the determination of metals in soil samples collected in Zona da Mata, Pernambuco, Brazil, where normally the application of pesticides, insecticides and other agricultural additives are used in a disorderly manner and without control. A total of 24 sampling points were monitored. The analysis of Mn, Fe, Ni, Zn, Br, Rb, Sr, Pb, Ti, La, Al, Si and P were performed using Energy Dispersive X-Ray Fluorescence. In order to assess the development of analytical method, inorganic Certified Reference Materials (IAEA-SOIL-7 and SRM 2709) were analyzed. In each sampling site, the geoaccumulation index were calculated to estimate the level of metal contamination in the soil, this was made taking into account the resolution 460 of the National Environmental Council (CONAMA in Portuguese). The elemental distribution patterns obtained for each metal were associated with different pollution sources. This assessment provides an initial description of pollution levels presented by metals in soils from several areas of Zona da Mata, providing quantitative evidence and demonstrating the need to improve the regulation of agricultural and industrial activities. (author)

Summary of Inorganic Compositional Data for Groundwater, Soil-Water, and Surface-Water Samples at the Headgate Draw Subsurface Drip Irrigation Site

Energy Technology Data Exchange (ETDEWEB)

Geboy, Nicholas J.; Engle, Mark A.; Schroeder, Karl T.; Zupanic, John W.

2007-01-01

As part of a 5-year project on the impact of subsurface drip irrigation (SDI) application of coalbed-methane (CBM) produced waters, water samples were collected from the Headgate Draw SDI site in the Powder River Basin, Wyoming, USA. This research is part of a larger study to understand short- and long-term impacts on both soil and water quality from the beneficial use of CBM waters to grow forage crops through use of SDI. This document provides a summary of the context, sampling methodology, and quality assurance and quality control documentation of samples collected prior to and over the first year of SDI operation at the site (May 2008-October 2009). This report contains an associated database containing inorganic compositional data, water-quality criteria parameters, and calculated geochemical parameters for samples of groundwater, soil water, surface water, treated CBM waters, and as-received CBM waters collected at the Headgate Draw SDI site.

Study of the Behavior and Distribution of Mercury in Soil Samples Collected on the Banks of the Valdeazogues River

International Nuclear Information System (INIS)

Lominchar, M. A.; Sierra, M. J.; Rodiriguez, J.; Millam, R.

2010-01-01

The main objective of this study is to determine the behavior of mercury in the soil of the Valdeazogues river (Almaden, Ciudad Real, Spain) by using a six-step sequential extraction procedure (CIEMAT) and checking the relationship between the percentage of organic matter in soil and the percentage of mercury associated with the exchangeable and oxidizable fractions. The results show that total mercury concentrations in soil range from 116.7 ±24.3 to 245.5 ±59.6 mg kg - 1 of Hg even to concentrations of 350.9 ±68.6 mg kg -1 . However, the available mercury concentration is a smaller percentage of 0.15% of total mercury measured in the samples. Also, the soluble mercury is less than 0,037 mg kg - 1, so that, the leaching process and transport of mercury to surface water and groundwater are very slow. With regard to the distribution of mercury between the different fractions of soil, the metal is associated with more resistant soil fractions, these are: crystalline Fe-Mn oxyhydroxides, organic matter absorbed and the fi nal residue. (Author9) 50 refs.

USE OF SCALED SEMIVARIOGRAMS IN THE PLANNING SAMPLE OF SOIL CHEMICAL PROPERTIES IN SOUTHERN AMAZONAS, BRAZIL

Directory of Open Access Journals (Sweden)

Ivanildo Amorim de Oliveira

2015-02-01

Full Text Available The lack of information concerning the variability of soil properties has been a major concern of researchers in the Amazon region. Thus, the aim of this study was to evaluate the spatial variability of soil chemical properties and determine minimal sampling density to characterize the variability of these properties in five environments located in the south of the State of Amazonas, Brazil. The five environments were archaeological dark earth (ADE, forest, pasture land, agroforestry operation, and sugarcane crop. Regular 70 × 70 m mesh grids were set up in these areas, with 64 sample points spaced at 10 m distance. Soil samples were collected at the 0.0-0.1 m depth. The chemical properties of pH in water, OM, P, K, Ca, Mg, H+Al, SB, CEC, and V were determined at these points. Data were analyzed by descriptive and geostatistical analyses. A large part of the data analyzed showed spatial dependence. Chemical properties were best fitted to the spherical model in almost all the environments evaluated, except for the sugarcane field with a better fit to the exponential model. ADE and sugarcane areas had greater heterogeneity of soil chemical properties, showing a greater range and higher sampling density; however, forest and agroforestry areas had less variability of chemical properties.

Degradation of aldrin im samples of 'cerrado' Brazilian soils

International Nuclear Information System (INIS)

Musumeci, M.R.; Ruegg, E.F.

1981-01-01

14 C-aldrin degradation was studied in the laboratory, in samples of 'cerrado' Brazilian soils, during a period of 240 days. Recovery of radiocarbon decreased with time, although radiocarbon was not incorporated to the soil organic matter as show by soil combustion. In both soils 14 C-aldrin degraded to dieldrin and another compound that showed caracteristics of a hydrosoluble derivative of aldrin 14 C-aldrin was more persistent in sandy soil but amendment of this soil with nutrients or fertilizers did not enhanced aldrin degradation in this soil. (Author) [pt

Using Environmental Variables for Studying of the Quality of Sampling in Soil Mapping

OpenAIRE

A. Jafari; Norair Toomanian; R. Taghizadeh Mehrjerdi

2016-01-01

Introduction: Methods of soil survey are generally empirical and based on the mental development of the surveyor, correlating soil with underlying geology, landforms, vegetation and air-photo interpretation. Since there are no statistical criteria for traditional soil sampling; this may lead to bias in the areas being sampled. In digital soil mapping, soil samples may be used to elaborate quantitative relationships or models between soil attributes and soil covariates. Because the relationshi...

Measurement of radioactivity in the environment - Soil - Part 2: Guidance for the selection of the sampling strategy, sampling and pre-treatment of samples

International Nuclear Information System (INIS)

2007-01-01

This part of ISO 18589 specifies the general requirements, based on ISO 11074 and ISO/IEC 17025, for all steps in the planning (desk study and area reconnaissance) of the sampling and the preparation of samples for testing. It includes the selection of the sampling strategy, the outline of the sampling plan, the presentation of general sampling methods and equipment, as well as the methodology of the pre-treatment of samples adapted to the measurements of the activity of radionuclides in soil. This part of ISO 18589 is addressed to the people responsible for determining the radioactivity present in soil for the purpose of radiation protection. It is applicable to soil from gardens, farmland, urban or industrial sites, as well as soil not affected by human activities. This part of ISO 18589 is applicable to all laboratories regardless of the number of personnel or the range of the testing performed. When a laboratory does not undertake one or more of the activities covered by this part of ISO 18589, such as planning, sampling or testing, the corresponding requirements do not apply. Information is provided on scope, normative references, terms and definitions and symbols, principle, sampling strategy, sampling plan, sampling process, pre-treatment of samples and recorded information. Five annexes inform about selection of the sampling strategy according to the objectives and the radiological characterization of the site and sampling areas, diagram of the evolution of the sample characteristics from the sampling site to the laboratory, example of sampling plan for a site divided in three sampling areas, example of a sampling record for a single/composite sample and example for a sample record for a soil profile with soil description. A bibliography is provided

Uranium determination in soil samples using Eichrom resins

International Nuclear Information System (INIS)

Marabini, S.; Serdeiro, Nelidad H.

2003-01-01

Traditionally, the radiochemical methods for uranium activity determination in soil samples by alpha spectrometry, use some techniques like solvent extraction, precipitation and ion exchange in the separation and purification stages. In the last years, some new materials have been developed for using in extraction chromatography, specific for actinides determinations. In the present method the long and tedious stages were eliminated, and the reagents consumption and concentration were minimised. This new procedure was applied to soils since it is one of the most complex matrices. In order to reduce time and chemical reagents, the soil samples up to 0,5 g were leached with nitric, hydrofluoric and perchloric acids in hermetic sealed recipients of Teflon at 150 C degrees during 5 hours. UTEVA Eichrom resin was used for uranium separation and purification. The uranium activity concentration was determined by alpha spectrometry. Several standard samples were analysed and the results are presented. (author)

High-throughput diagnosis of potato cyst nematodes in soil samples.

Science.gov (United States)

Reid, Alex; Evans, Fiona; Mulholland, Vincent; Cole, Yvonne; Pickup, Jon

2015-01-01

Potato cyst nematode (PCN) is a damaging soilborne pest of potatoes which can cause major crop losses. In 2010, a new European Union directive (2007/33/EC) on the control of PCN came into force. Under the new directive, seed potatoes can only be planted on land which has been found to be free from PCN infestation following an official soil test. A major consequence of the new directive was the introduction of a new harmonized soil sampling rate resulting in a threefold increase in the number of samples requiring testing. To manage this increase with the same staffing resources, we have replaced the traditional diagnostic methods. A system has been developed for the processing of soil samples, extraction of DNA from float material, and detection of PCN by high-throughput real-time PCR. Approximately 17,000 samples are analyzed each year using this method. This chapter describes the high-throughput processes for the production of float material from soil samples, DNA extraction from the entire float, and subsequent detection and identification of PCN within these samples.

Studies and further needed investigations on radioactive contaminants in soil samples

International Nuclear Information System (INIS)

Belivermis, M.; Kilic, O.; Topcuoglu, S.; Cotuk, Y.; Kalayci, G.; Pestreli, D.

2009-01-01

Following the Chernobyl nuclear reactor accident, the radionuclides were deposited on the marine and terrestrial environments of Turkey and other countries as wet and / or dry fallout. It is well known that, the soil is the main reservoir at the terrestrial environment. The geographic distribution of the Chernobyl radionuclides per unit area is significantly different. Many countries have drawn radiation maps using the radionuclide data of the soil samples. The radioecological monitoring study in the soil samples are also investigated in the our country. However, the exist data is limited for whole region of Turkey. In general, the type study, that make, in uncultivated soil sample use of different soil layers (0-5, 5-10, 10-20, 20-30 cm). In our previous studies, the activity concentration of gamma emitting radionuclides were determined in soil samples (0-5 cm) from the Thrace (73 sites) and East and South Marmara (100 sites) regions. Moreover, the mean values of the annual effective dose equivalent were also calculated. In literature, numerous studies have been published concerning vertical migration of 1 37Cs in uncultivated soil samples use of different soil types. However, we have not enough data on this subject. On the other hand, we want to present a previously published data on the vertical distribution of 1 37Cs radionuclide in an uncultivated site in the eastern Black Sea region. It is well known that the determination of soil to plant transfer factors of radiocesium that take account all economically crops on the soil varieties is a need to support dose assessment or countermeasure studies. Previously published IAEA reports, we determined transfer factors for some crops of 1 37Cs radionuclides in cultivated soil samples (0-20 cm depth) in the eastern Black Sea region. At the same time, we have given a new project to IAEA for the determination of transfer factor of radiocesium from soil to some crops for Akkuyu Nuclear Power Plant site.

Investigation of the uranium content in sediment and soil samples from the Santos and Sao Vicente estuary region, SP, Brazil

International Nuclear Information System (INIS)

Serafim, Ricardo A.M.; Correa, Bianca A.M.; Primi, M.C.; Geraldo, Luiz P.; Yamazaki, Yone M.

2009-01-01

In this work the uranium (U) content in sediment and soil samples collected near the Santos and Sao Vicente estuary was determined using the fission track registration technique (SSNTD). The sediment and soil samples after oven-dried and pulverized were prepared in the solution form. Around 10 μL of this solution was deposited on the plastic detector (PCLIGHT) and irradiated at the IEA-R1 (3.5 MW) nuclear reactor. After the irradiation and chemical etching of the plastic foils, the fission tracks were counted with a system consisting of an optical microscope together with a video camera and a PC computer. The U content in the analyzed samples ranged from 3.12 ± 0.55 to 18.3 ± 1.2 ppm for sediments and from 3.21 ± 0.63 to 11.5 ± 1.1 ppm for soils. These results were compared to other values reported in the literature for sediments and soils collected in environments similar to the ones studied in this work The average values for the U content obtained in this work are significant higher (above twice) than the world mean and are in reasonable agreement with results found by other authors for sediments and soils from regions considered as polluted or with a high level of radioactivity. (author)

Sampling and Mapping Soil Erosion Cover Factor for Fort Richardson, Alaska. Integrating Stratification and an Up-Scaling Method

National Research Council Canada - National Science Library

Wang, Guangxing; Gertner, George; Anderson, Alan B; Howard, Heidi

2006-01-01

When a ground and vegetation cover factor related to soil erosion is mapped with the aid of remotely sensed data, a cost-efficient sample design to collect ground data and obtain an accurate map is required...

Curiosity analyzes Martian soil samples

Science.gov (United States)

Showstack, Randy; Balcerak, Ernie

2012-12-01

NASA's Mars Curiosity rover has conducted its first analysis of Martian soil samples using multiple instruments, the agency announced at a 3 December news briefing at the AGU Fall Meeting in San Francisco. "These results are an unprecedented look at the chemical diversity in the area," said NASA's Michael Meyer, program scientist for Curiosity.

Central Colorado Assessment Project (CCAP)-Geochemical data for rock, sediment, soil, and concentrate sample media

Science.gov (United States)

Granitto, Matthew; DeWitt, Ed H.; Klein, Terry L.

2010-01-01

This database was initiated, designed, and populated to collect and integrate geochemical data from central Colorado in order to facilitate geologic mapping, petrologic studies, mineral resource assessment, definition of geochemical baseline values and statistics, environmental impact assessment, and medical geology. The Microsoft Access database serves as a geochemical data warehouse in support of the Central Colorado Assessment Project (CCAP) and contains data tables describing historical and new quantitative and qualitative geochemical analyses determined by 70 analytical laboratory and field methods for 47,478 rock, sediment, soil, and heavy-mineral concentrate samples. Most samples were collected by U.S. Geological Survey (USGS) personnel and analyzed either in the analytical laboratories of the USGS or by contract with commercial analytical laboratories. These data represent analyses of samples collected as part of various USGS programs and projects. In addition, geochemical data from 7,470 sediment and soil samples collected and analyzed under the Atomic Energy Commission National Uranium Resource Evaluation (NURE) Hydrogeochemical and Stream Sediment Reconnaissance (HSSR) program (henceforth called NURE) have been included in this database. In addition to data from 2,377 samples collected and analyzed under CCAP, this dataset includes archived geochemical data originally entered into the in-house Rock Analysis Storage System (RASS) database (used by the USGS from the mid-1960s through the late 1980s) and the in-house PLUTO database (used by the USGS from the mid-1970s through the mid-1990s). All of these data are maintained in the Oracle-based National Geochemical Database (NGDB). Retrievals from the NGDB and from the NURE database were used to generate most of this dataset. In addition, USGS data that have been excluded previously from the NGDB because the data predate earliest USGS geochemical databases, or were once excluded for programmatic reasons

Aluminium, extractable from soil samples by the acid ammonium acetate soil-testing method

Directory of Open Access Journals (Sweden)

Osmo Mäkitie

1968-05-01

Full Text Available The extractant, 0.5 M acetic acid –0.5 M ammonium acetate at pH 4.65, which is used in soil-testing, extracts relatively high amounts of aluminium from acid soils. The mean values of acetate-extractable aluminium at pH 4.65, 1.75 meq Al/100 g of soil, and of exchangeable aluminium (M KCI extraction, 0.41 meq Al were obtained from a material of 30 samples of acid soils (Table 2. Several other acetic acid ammonium acetate extractants, from M acetic acid to M ammonium acetate solution were also used for studying the extractability of soil aluminium. The soil-testing extractant can be used for the estimation of the soluble amounts of aluminium in acid soils, however, further studies are needed for a better interpretation of the ammonium acetate extractable (at pH 4.65 aluminium in our soils.

Laboratory and Airborne BRDF Analysis of Vegetation Leaves and Soil Samples

Science.gov (United States)

Georgiev, Georgi T.; Gatebe, Charles K.; Butler, James J.; King, Michael D.

2008-01-01

Laboratory-based Bidirectional Reflectance Distribution Function (BRDF) analysis of vegetation leaves, soil, and leaf litter samples is presented. The leaf litter and soil samples, numbered 1 and 2, were obtained from a site located in the savanna biome of South Africa (Skukuza: 25.0degS, 31.5degE). A third soil sample, number 3, was obtained from Etosha Pan, Namibia (19.20degS, 15.93degE, alt. 1100 m). In addition, BRDF of local fresh and dry leaves from tulip tree (Liriodendron tulipifera) and acacia tree (Acacia greggii) were studied. It is shown how the BRDF depends on the incident and scatter angles, sample size (i.e. crushed versus whole leaf,) soil samples fraction size, sample status (i.e. fresh versus dry leaves), vegetation species (poplar versus acacia), and vegetation s biochemical composition. As a demonstration of the application of the results of this study, airborne BRDF measurements acquired with NASA's Cloud Absorption Radiometer (CAR) over the same general site where the soil and leaf litter samples were obtained are compared to the laboratory results. Good agreement between laboratory and airborne measured BRDF is reported.

[PHAHs levels in soil samples from the E-waste disassembly sites and their sources allocation].

Science.gov (United States)

Zhao, Gao-Feng; Wang, Zi-Jian

2009-06-15

Soil samples (each with 3 replicates of - 1 kg, at the top 0-5 cm layer) were collected from each of the e-waste disassembly sites and the control site. Also obtained from each disassembly site were samples (each weighing - 0.2 kg) of cable coating,stuffing powder, and circuit boards chipping. The contents of 23 PBB congeners, 12 PBDE congeners, and 27 PCB congeners in soil and in their potential sources, including e-waste residues, were measured using the GC-MS5975B technique. The highest level of PBBs was found in the cable coating among the three e-waste residues, with a concentration of 35.25 ng x g(-1). The contents of low-brominated PBBs (including monobromobiphenyls and dibromobiphenyls) accounted for 38% of the total PBBs concentration observed in cable coating sample. The highest levels of PBDEs and PBDE209 were found in the stuffing powder for electronic component among the collected e-waste residues, with a concentration of 29.71 and 4.19 x 10(3) ng x g(-1). PBDE153 and PBDE183 were the most predominant PBDE congeners, with their concentration accounting for 43% and 24% of the total PBDEs concentration observed in the stuffing powder sample, respectively. Levels of PCBs in cable coating were the highest in these e-waste residues, with a concentration of 680.02 ngx g(-1). The observed values of the three PHAHs in soils from the disassembly site were considerably higher than their corresponding values observed in the control site (p < 0.05), which indicates that these PHAHs from e-waste is the pollution source of local environment.

Iron Quadrangle, Brazil. Elemental concentration determined by k0-instrumental neutron activation analysis. Part 1. Soil samples

International Nuclear Information System (INIS)

Menezes, M.A.B.C.; Palmieri, H.E.L.; Leonel, L.V.; Nalini, H.A.Jr.; Jacimovic, R.

2006-01-01

The Iron Quadrangle, Minas Gerais, Brazil, is rich in mineral occurrences and is considered one of the richest mineral-bearing regions in the world. Most investigations in this region have dealt with the determination of arsenic and mercury but so far few studies have been carried out aiming at determining other important elements. Having in mind the potential risk caused by mineral activities, this study was developed in order to assess the potential influence of the soil on foodstuffs. The soil samples were collected from three sites inside and outside the Iron Quadrangle. The samples were analyzed at the Laboratory for Neutron Activation Analysis, CDTN/CNEN by the k 0 -instrumental neutron activation analysis. This paper reports the elemental concentration determined in soil and emphasises the elements cited in the Brazilian environmental legislation for soil. This work also confirms the high elemental concentration of several minerals, however, it is difficult to distinguish the contamination from anthropogenic activities from the natural occurrence. (author)

Towards quantitative laser-induced breakdown spectroscopy analysis of soil samples

International Nuclear Information System (INIS)

Bousquet, B.; Sirven, J.-B.; Canioni, L.

2007-01-01

A quantitative analysis of chromium in soil samples is presented. Different emission lines related to chromium are studied in order to select the best one for quantitative features. Important matrix effects are demonstrated from one soil to the other, preventing any prediction of concentration in different soils on the basis of a univariate calibration curve. Finally, a classification of the LIBS data based on a series of Principal Component Analyses (PCA) is applied to a reduced dataset of selected spectral lines related to the major chemical elements in the soils. LIBS data of heterogeneous soils appear to be widely dispersed, which leads to a reconsideration of the sampling step in the analysis process

Determination of concentrations of chromium and other elements in soil and plant samples from leather tanning area by Instrumental Neutron Activation Analysis

International Nuclear Information System (INIS)

Rohit Kumar; Rai, A.K.; Alamelu, D.; Acharya, R.

2014-01-01

Chromium, one of the toxic elements, along with other elements has been determined in samples of soil and plant (leaves and seeds) from Jajmau Area, Kanpur district, India, which is irrigated with effluent waste water from leather tanning industries. Soil and plant samples were collected from these areas and analyzed by Instrumental Neutron Activation Analysis (INAA) using high flux reactor neutrons and high resolution gamma-ray spectrometry. Concentrations of fifteen elements in soil and five elements in plant samples were determined by relative method. Chromium concentrations were found to be in range of 45-3,900 mg kg -1 in soil samples and 14-83 mg kg -1 in plant samples. This study showed that Cr is present in significant amounts, in the soil as well as in the plant samples, near to the leather tanning area. As a part of quality control work, IAEA reference material (RM) SL-3 and NIST standard reference material (SRM) 1645 were analyzed and the quality of the results has been evaluated by calculating % deviations from recommended/literature/certified values. (author)

Soil-to-plant transfer factors of technetium-99 for various plants collected in the Chernobyl area

International Nuclear Information System (INIS)

Tagami, Keiko; Uchida, Shigeo

2005-01-01

Technetium-99 is thought to be highly soluble and rarely adsorbed onto soil, however, its mobility under natural environment is not well known because its scarcity and low levels in environmental samples has limited the available data. In this study, we determined 99 Tc contents in 27 plant samples collected in three forest sites in 1994 and 1995 around the Chernobyl area to obtain transfer factors (TFs) of Tc in the soil-plant system under environmental conditions. The samples were leaves of raspberry, strawberry and pink plants, black alder, birch, cowberry and oak trees, and ferns. After chemical separation, 99 Tc in the sample was measured by ICP-MS. Tc-95m was used as a yield tracer and the total recovery ranged from 0.48 to 0.92 with an average of 0.76. The determined 99 Tc concentrations in plants ranged from -1 (dry weight basis). TF values ranged from 99 Tc contents of the soil organic layers. The highest TF was found in the leaves of raspberry plants. The observed TFs were much lower than the values of 8.1 - 2600 compiled by IAEA for grass, fodder and leafy vegetables. (author)

Results of analyses of fur samples from the San Joaquin Kit Fox and associated soil and water samples from the Naval Petroleum Reserve No. 1, Tupman, California

Energy Technology Data Exchange (ETDEWEB)

Suter, G.W. II; Rosen, A.E.; Beauchamp, J.J. (Oak Ridge National Lab., TN (United States)); Kato, T.T. (EG and G Energy Measurements, Inc., Tupman, CA (United States))

1992-12-01

The purpose of this study was to determine whether analysis of the elemental content of fur from San Joaquin kit foxes (Vulpes macrotis mutica) and of water and soil from kit fox habitats could be used to make inferences concerning the cause of an observed decline in the kit fox population on Naval Petroleum Reserve No. 1 (NPR-1). Fur samples that had been collected previously from NPR-1, another oil field (NPR-2), and two sites with no oil development were subjected to neutron activation analysis. In addition, soil samples were collected from the home ranges of individual foxes from undisturbed portions of major soil types on NPR-1 and from wastewater samples were collected from tanks and sumps and subjected to neutron activation analysis. Most elemental concentrations in fur were highest at Camp Roberts and lowest on the undeveloped portions of NPR-I. Fur concentrations were intermediate on the developed oil fields but were correlated with percent disturbance and with number of wells on NPR-1 and NPR-2. The fact that most elements covaried across the range of sites suggests that some pervasive source such as soil was responsible. However, fur concentrations were not correlated with soft concentrations. The kit foxes on the developed portion of NPR-1 did not have concentrations of elements in fur relative to other sites that would account for the population decline in the early 1980s. The oil-related elements As, Ba, and V were elevated in fox fur from oil fields, but only As was sufficiently elevated to suggest a risk of toxicity in individual foxes. However, arsenic concentrations suggestive of sublethal toxicity were found in only 0.56% of foxes from developed oil fields, too few to account for a population decline.

Estimation of radon concentration in soil and groundwater samples of Northern Rajasthan, India

Directory of Open Access Journals (Sweden)

Sudhir Mittal

2016-04-01

Full Text Available In the present investigation, analysis of radon concentration in 20 water and soil samples collected from different locations of Bikaner and Jhunjhunu districts of Rajasthan, India has been carried out by using RAD7 an electronic Radon detector. The measured radon concentration in water samples lies in the range from 0.50 to 22 Bq l−1 with the mean value of 4.42 Bq l−1, which lies within the safe limit from 4 to 40 Bq l−1 recommended by United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR, 2008. The total annual effective dose estimated due to radon concentration in water ranges from 1.37 to 60.06 μSV y−1 with the mean value of 12.08 μSV y−1, which is lower than the safe limit 0.1 mSv y−1 as set by World Health Organization (WHO, 2004 and European Council (EU, 1998. Radon measurement in soil samples varies from 941 to 10,050 Bq m−3 with the mean value of 4561 Bq m−3, which lies within the range reported by other investigators. It was observed that the soil and water of Bikaner and Jhunjhunu districts are suitable for drinking and construction purpose without posing any health hazard.

Micro-PIXE evaluation of radioactive cesium transfer in contaminated soil samples

International Nuclear Information System (INIS)

Fujishiro, F.; Ishii, K.; Matsuyama, S.; Arai, H.; Ishizaki, A.; Osada, N.; Sugai, H.; Kusano, K.; Nozawa, Y.; Yamauchi, S.; Karahashi, M.; Oshikawa, S.; Kikuchi, K.; Koshio, S.; Watanabe, K.; Suzuki, Y.

2014-01-01

Highlights: • There are radioactively contaminated soils having a radioactive cesium transfer of 0.01. • Micro-PIXE analysis has revealed an existence of phosphorus in a contaminated soil. • Radioactive cesium captured by phosphorus compound would be due to radioactive transfer. -- Abstract: Micro-PIXE analysis has been performed on two soil samples with high cesium activity concentrations. These soil samples were contaminated by fallout from the accident at Fukushima Daiichi Nuclear Power Plant. One exhibits a radioactive cesium transfer of ∼0.01, and the other shows a radioactive cesium transfer of less than 0.001, even though both samples have high cesium activity concentrations exceeding 10,000 Bq/kg. X-ray spectra and elemental images of the soil samples revealed the presence of chlorine, which can react with cesium to produce an inorganic soluble compound, and phosphorus-containing cesium-capturable organic compounds

Fingerprinting of petroleum hydrocarbons (PHC) and other biogenic organic compounds (BOC) in oil-contaminated and background soil samples.

Science.gov (United States)

Wang, Zhendi; Yang, C; Yang, Z; Hollebone, B; Brown, C E; Landriault, M; Sun, J; Mudge, S M; Kelly-Hooper, F; Dixon, D G

2012-09-01

Total petroleum hydrocarbons (TPH) or petroleum hydrocarbons (PHC) are one of the most widespread soil contaminants in Canada, the United States and many other countries worldwide. Clean-up of PHC-contaminated soils costs the Canadian economy hundreds of millions of dollars annually. In Canada, most PHC-contaminated site evaluations are based on the methods developed by the Canadian Council of the Ministers of the Environment (CCME). However, the CCME method does not differentiate PHC from BOC (the naturally occurring biogenic organic compounds), which are co-extracted with petroleum hydrocarbons in soil samples. Consequently, this could lead to overestimation of PHC levels in soil samples. In some cases, biogenic interferences can even exceed regulatory levels (300 μg g(-1) for coarse soils and 1300 μg g(-1) for fine soils for Fraction 3, C(16)-C(34) range, in the CCME Soil Quality Level). Resulting false exceedances can trigger unnecessary and costly cleanup or remediation measures. Therefore, it is critically important to develop new protocols to characterize and quantitatively differentiate PHC and BOC in contaminated soils. The ultimate objective of this PERD (Program of Energy Research and Development) project is to correct the misconception that all detectable hydrocarbons should be regulated as toxic petroleum hydrocarbons. During 2009-2010, soil and plant samples were collected from over forty oil-contaminated and paired background sites in various provinces. The silica gel column cleanup procedure was applied to effectively remove all target BOC from the oil-contaminated sample extracts. Furthermore, a reliable GC-MS method in combination with the derivatization technique, developed in this laboratory, was used for identification and characterization of various biogenic sterols and other major biogenic compounds in these oil-contaminated samples. Both PHC and BOC in these samples were quantitatively determined. This paper reports the characterization

Recovery of Soil Microbial Community Structure in a Wildfire Impacted Forest Soil

Science.gov (United States)

Tate, Robert, III; Mikita, Robyn

2010-05-01

Wildfires are common disturbances that will increase in frequency and intensity as a result of conditions associated with the changing climate. In turn, forest fires exacerbate climate conditions by increasing carbon and atmospheric aerosols, and changing the surface albedo. Fires have significant economic, environmental, and ecological repercussions; however, we have a limited understanding on the effect of severe wildfires on the composition, diversity, and function of belowground microorganisms. The objective of this research was to examine the shift of the forest soil microbial community as a result of a severe wildfire in the New Jersey Pinelands. Over the span of two years following the fire, soil samples from the organic and mineral layers of the severely burned sites were collected six times. Samples were also collected twice from an unburned control site. It was hypothesized that soil microbial communities from severely burned samples collected shortly after the fire would be significantly different from (1) the unburned samples that serve as controls and (2) the severely burned samples collected more than a year after the fire. Microbial community composition was analyzed by principal component analysis and multivariate analysis of variance of molecular fingerprint data from denaturing gradient gel electrophoresis of bacterial and archaeal-specific amplicons. Bacterial community composition was significantly different among all the organic and mineral layer samples collected 2, 5, 13, and 17 months following the fire. This indicated a shift in the bacterial communities with time following the fire. Common phylotypes from the burned organic layer samples collected 2 months after the fire related closely to members of the phyla Cyanobacteria and Acidobacteria, whereas those from later samples (5, 13, and 17 months following the fire) were closely related to members of the genus Mycobacteria. Canonical correlation analysis was used to determine connections

Sampling errors associated with soil composites used to estimate mean Ra-226 concentrations at an UMTRA remedial-action site

International Nuclear Information System (INIS)

Gilbert, R.O.; Baker, K.R.; Nelson, R.A.; Miller, R.H.; Miller, M.L.

1987-07-01

The decision whether to take additional remedial action (removal of soil) from regions contaminated by uranium mill tailings involves collecting 20 plugs of soil from each 10-m by 10-m plot in the region and analyzing a 500-g portion of the mixed soil for 226 Ra. A soil sampling study was conducted in the windblown mill-tailings flood plain area at Shiprock, New Mexico, to evaluate whether reducing the number of soil plugs to 9 would have any appreciable impact on remedial-action decisions. The results of the Shiprock study are described and used in this paper to develop a simple model of the standard deviation of 226 Ra measurements on composite samples formed from 21 or fewer plugs. This model is used to predict as a function of the number of soil plugs per composite, the percent accuracy with which the mean 226 Ra concentration in surface soil can be estimated, and the probability of making incorrect remedial action decisions on the basis of statistical tests. 8 refs., 15 figs., 9 tabs

The Effect of Sample Size and Data Numbering on Precision of Calibration Model to predict Soil Properties

Directory of Open Access Journals (Sweden)

H Mohamadi Monavar

2017-10-01

Full Text Available Introduction Precision agriculture (PA is a technology that measures and manages within-field variability, such as physical and chemical properties of soil. The nondestructive and rapid VIS-NIR technology detected a significant correlation between reflectance spectra and the physical and chemical properties of soil. On the other hand, quantitatively predict of soil factors such as nitrogen, carbon, cation exchange capacity and the amount of clay in precision farming is very important. The emphasis of this paper is comparing different techniques of choosing calibration samples such as randomly selected method, chemical data and also based on PCA. Since increasing the number of samples is usually time-consuming and costly, then in this study, the best sampling way -in available methods- was predicted for calibration models. In addition, the effect of sample size on the accuracy of the calibration and validation models was analyzed. Materials and Methods Two hundred and ten soil samples were collected from cultivated farm located in Avarzaman in Hamedan province, Iran. The crop rotation was mostly potato and wheat. Samples were collected from a depth of 20 cm above ground and passed through a 2 mm sieve and air dried at room temperature. Chemical analysis was performed in the soil science laboratory, faculty of agriculture engineering, Bu-ali Sina University, Hamadan, Iran. Two Spectrometer (AvaSpec-ULS 2048- UV-VIS and (FT-NIR100N were used to measure the spectral bands which cover the UV-Vis and NIR region (220-2200 nm. Each soil sample was uniformly tiled in a petri dish and was scanned 20 times. Then the pre-processing methods of multivariate scatter correction (MSC and base line correction (BC were applied on the raw signals using Unscrambler software. The samples were divided into two groups: one group for calibration 105 and the second group was used for validation. Each time, 15 samples were selected randomly and tested the accuracy of

BOREAS TE-2 NSA Soil Lab Data

Science.gov (United States)

Veldhuis, Hugo; Hall, Forrest G. (Editor); Knapp, David E. (Editor)

2000-01-01

This data set contains the major soil properties of soil samples collected in 1994 at the tower flux sites in the Northern Study Area (NSA). The soil samples were collected by Hugo Veldhuis and his staff from the University of Manitoba. The mineral soil samples were largely analyzed by Barry Goetz, under the supervision of Dr. Harold Rostad at the University of Saskatchewan. The organic soil samples were largely analyzed by Peter Haluschak, under the supervision of Hugo Veldhuis at the Centre for Land and Biological Resources Research in Winnipeg, Manitoba. During the course of field investigation and mapping, selected surface and subsurface soil samples were collected for laboratory analysis. These samples were used as benchmark references for specific soil attributes in general soil characterization. Detailed soil sampling, description, and laboratory analysis were performed on selected modal soils to provide examples of common soil physical and chemical characteristics in the study area. The soil properties that were determined include soil horizon; dry soil color; pH; bulk density; total, organic, and inorganic carbon; electric conductivity; cation exchange capacity; exchangeable sodium, potassium, calcium, magnesium, and hydrogen; water content at 0.01, 0.033, and 1.5 MPascals; nitrogen; phosphorus: particle size distribution; texture; pH of the mineral soil and of the organic soil; extractable acid; and sulfur. These data are stored in ASCII text files. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Statistical sampling strategies for survey of soil contamination

NARCIS (Netherlands)

Brus, D.J.

2011-01-01

This chapter reviews methods for selecting sampling locations in contaminated soils for three situations. In the first situation a global estimate of the soil contamination in an area is required. The result of the surey is a number or a series of numbers per contaminant, e.g. the estimated mean

Concentrations of major and trace elements in polished rice and paddy soils collected in Aomori, Japan

International Nuclear Information System (INIS)

Tsukada, H.; Hasegawa, H.; Takeda, A.; Hisamatsu, S.

2005-01-01

Rice is a staple food in most Asian countries including Japan, and it is important to evaluate the intake of elements through polished rice ingestion in daily life. Rice grain samples and surface paddy soil samples were collected from 20 sites throughout Aomori Prefecture, Japan. Rice grains were threshed and then polished to 90% of the total weight of brown rice. The polished rice samples for the determination of the neutron activation analysis (NAA) were dried at 50 degree C and those of the inductively coupled plasma-mass spectrometer (ICP-MS) were ashed at a temperature below 450 degree C to avoid loss of alkali metals. The soil samples were dried at 50 degree C and were pulverized with an agate ball mill. The concentrations of As, Cl and I in the polished rice and As, Cl, I, Ti and Zr in the soils were determined by the NAA. The concentrations of 22 elements in the polished rice and 28 elements in the soils were determined by the ICP-MS. The mean concentrations of essential elements in the polished rice such as K, Mg, Cl, Ca, Zn, Mn, Fe, Cu and Mo were 720, 270, 160, 54, 16, 9.7, 2.3, 21 and 0.47 mg kg -1 dry weight, respectively, and the range of each element was within one order of magnitude. However, the ranges of most trace elements in the polished rice including Al, Ni, Ba, Cd, Pb, Cr, I, Ag and Cs were more than one order of magnitude. The mean concentrations of non-essential elements in the polished rice were as follows: Na, 11; Al, 3.9; Rb, 1.2; Ni, 0.11; As, Sr, Ba, Cd, V and Pb, 0.1-0.01; Cr, I, Co, Ag, Se and Cs, O.Ol-0.001 mg kg -1 dry weight. The concentration ranges of elements, except for I, in the paddy soils were within one order of magnitude. The mean concentrations of elements in the soils were as follows: Al, Fe, Ca and Na, 100000-10000; Mg, K and Ti, 10000-1000; Mn, Ba, Cl, Zr, Sr and Zn, 1000-100; V, Ce, Cr, Rb, Cu, Pb, Sc, La, As and Ni, 100-10; Co, Th, Cs, I, U, Mo and Se, 10-1; Sb, Cd and Ag, 1-0.1 mg kg -1 . The mean concentrations of

Soil sampling in emergency situations; Amostragem de solos em situacoes de emergencia

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Zenildo Lara de [Instituto de Radioprotecao e Dosimetria (IRD), Rio de Janeiro, RJ (Brazil); Ramos Junior, Anthenor Costa [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil). Superintendencia de Licenciamento e Controle

1997-12-31

The soil sampling methods used in Goiania`s accident (1987) by the environmental team of Brazilian Nuclear Energy Commission (CNEN) are described. The development of this method of soil sampling to a emergency sampling method used in a Nuclear Emergency Exercise in Angra dos Reis Reactor Site (1991) is presented. A new method for soil sampling based on a Chernobyl environmental monitoring experience (1995) is suggested. (author) 15 refs.

Assessment of soil sample quality used for density evaluations through computed tomography

International Nuclear Information System (INIS)

Pires, Luiz F.; Arthur, Robson C.J.; Bacchi, Osny O.S.

2005-01-01

There are several methods to measure soil bulk density (ρ s ) like the paraffin sealed clod (PS), the volumetric ring (VR), the computed tomography (CT), and the neutron-gamma surface gauge (SG). In order to evaluate by a non-destructive way the possible modifications in soil structure caused by sampling for the PS and VR methods of ρ s evaluation we proposed to use the gamma ray CT method. A first generation tomograph was used having a 241 Am source and a 3 in x 3 in NaI(Tl) scintillation crystal detector coupled to a photomultiplier tube. Results confirm the effect of soil sampler devices on the structure of soil samples, and that the compaction caused during sampling causes significant alterations of soil bulk density. Through the use of CT it was possible to determine the level of compaction and to make a detailed analysis of the soil bulk density distribution within the soil sample. (author)

Radionuclide Concentrations in Terrestrial Vegetation and Soil Samples On and Around the Hanford Site, 1971 Through 2008

Energy Technology Data Exchange (ETDEWEB)

Simmons, Mary Ann; Poston, Ted M.; Fritz, Brad G.; Bisping, Lynn E.

2011-07-29

Environmental monitoring is conducted on the U.S. Department of Energy (DOE) Hanford Site to comply with DOE Orders and federal and state regulations. Major objectives of the monitoring are to characterize contaminant levels in the environment and to determine site contributions to the contaminant inventory. This report focuses on surface soil and perennial vegetation samples collected between 1971 and 2008 as part of the Pacific Northwest National Laboratory Surface Environmental Surveillance Project performed under contract to DOE. Areas sampled under this program are located on the Hanford Site but outside facility boundaries and on public lands surrounding the Hanford Site. Additional samples were collected during the past 8 years under DOE projects that evaluated parcels of land for radiological release. These data were included because the same sampling methodology and analytical laboratory were used for the projects. The spatial and temporal trends of six radionuclides collected over a 38-year period were evaluated. The radionuclides----cobalt-60, cesium-137, strontium-90, plutonium-238, plutonium-239/240, and uranium (reported either as uranium-238 or total uranium)----were selected because they persist in the environment and are still being monitored routinely and reported in Hanford Site environmental reports. All these radionuclides were associated with plutonium production and waste management of activities occurring on the site. Other sources include fallout from atmospheric testing of nuclear weapons, which ended in 1980, and the Chernobyl explosion in 1986. Uranium is also a natural component of the soil. This assessment of soil and vegetation data provides important information on the distribution of radionuclides in areas adjacent to industrial areas, established perimeter locations and buffer areas, and more offsite nearby and distant locations. The concentrations reflect a tendency for detection of some radionuclides close to where they were

Characterisation of a reference site for quantifying uncertainties related to soil sampling

International Nuclear Information System (INIS)

Barbizzi, Sabrina; Zorzi, Paolo de; Belli, Maria; Pati, Alessandra; Sansone, Umberto; Stellato, Luisa; Barbina, Maria; Deluisa, Andrea; Menegon, Sandro; Coletti, Valter

2004-01-01

An integrated approach to quality assurance in soil sampling remains to be accomplished. - The paper reports a methodology adopted to face problems related to quality assurance in soil sampling. The SOILSAMP project, funded by the Environmental Protection Agency of Italy (APAT), is aimed at (i) establishing protocols for soil sampling in different environments; (ii) assessing uncertainties associated with different soil sampling methods in order to select the 'fit-for-purpose' method; (iii) qualifying, in term of trace elements spatial variability, a reference site for national and international inter-comparison exercises. Preliminary results and considerations are illustrated

Uranium content and dose assessment for sediment and soil samples from the estuarine system of Santos and Sao Vicente, SP (Brazil)

International Nuclear Information System (INIS)

Geraldo, L. P.; Serafim, R. A. M.; Correa, B. A. M.; Yamazaki, I. M.; Primi, M. C.

2010-01-01

In this work, the uranium (U) content in sediment and soil samples collected near the Santos and Sao Vicente estuaries was determined using the fission track registration technique (SSNTD). The sediment and soil samples after oven-dried and pulverised were prepared in the solution form. About 10 ml of this solution was deposited on a plastic detector and irradiated at the IPEN-IEA-R1 (3.5 MW) nuclear reactor. After the irradiation and chemical etching of the plastic foils, the fission tracks were counted with a system consisting of an optical microscope together with a video camera and a PC. The U content in the analysed samples ranged from 3.12±0.55 to 18.3±1.2 ppm for sediments and from 3.21±0.63 to 11.5±1.1 ppm for soils or in terms of 238 U equivalent activity from 38.5±6.8 to 226±15 and 39.6±7.8 to 142±14 Bq kg -1 for sediments and soils, respectively. These results were compared with other values reported in the literature for sediments and soils collected in environments similar to the ones studied in this work. Most of the values obtained in this work are higher than the world mean and are in reasonable agreement with results found by other authors for sediments and soils from regions considered as polluted or with a high level of radioactivity. (authors)

Radioactivity concentrations and dose assessment in surface soil samples from east and south of Marmara region, Turkey.

Science.gov (United States)

Kiliç, Onder; Belivermis, Murat; Topçuoğlu, Sayhan; Cotuk, Yavuz; Coşkun, Mahmut; Cayir, Akin; Küçer, Rahmi

2008-01-01

The activity concentrations of 137Cs, 40K, 232Th, 238U and 226Ra were measured in surface soil samples from East and South of Marmara region, Turkey. The physico-chemical parameters (organic matter, CaCO3 contents and pH-value) of the soil samples were determined in the samples collected from 100 sampling stations. The average activity concentrations of 137Cs, 40K, 232Th, 238U and 226Ra were found to be 27.46+/-21.84, 442.51+/-189.85, 26.63+/-15.90, 21.77+/-12.08 and 22.45+/-13.31 Bq kg(-1), respectively. The mean value of total annual external gamma radiation dose equivalent for the natural radionuclides was calculated to be 54.86 microSv. The current data were compared with those found in the other locations of Turkey and different countries.

Decision support tool for soil sampling of heterogeneous pesticide (chlordecone) pollution.

Science.gov (United States)

Clostre, Florence; Lesueur-Jannoyer, Magalie; Achard, Raphaël; Letourmy, Philippe; Cabidoche, Yves-Marie; Cattan, Philippe

2014-02-01

When field pollution is heterogeneous due to localized pesticide application, as is the case of chlordecone (CLD), the mean level of pollution is difficult to assess. Our objective was to design a decision support tool to optimize soil sampling. We analyzed the CLD heterogeneity of soil content at 0-30- and 30-60-cm depth. This was done within and between nine plots (0.4 to 1.8 ha) on andosol and ferralsol. We determined that 20 pooled subsamples per plot were a satisfactory compromise with respect to both cost and accuracy. Globally, CLD content was greater for andosols and the upper soil horizon (0-30 cm). Soil organic carbon cannot account for CLD intra-field variability. Cropping systems and tillage practices influence the CLD content and distribution; that is CLD pollution was higher under intensive banana cropping systems and, while upper soil horizon was more polluted than the lower one with shallow tillage (pollution in the soil profile. The decision tool we proposed compiles and organizes these results to better assess CLD soil pollution in terms of sampling depth, distance, and unit at field scale. It accounts for sampling objectives, farming practices (cropping system, tillage), type of soil, and topographical characteristics (slope) to design a relevant sampling plan. This decision support tool is also adaptable to other types of heterogeneous agricultural pollution at field level.

Micro-PIXE evaluation of radioactive cesium transfer in contaminated soil samples

Science.gov (United States)

Fujishiro, F.; Ishii, K.; Matsuyama, S.; Arai, H.; Ishizaki, A.; Osada, N.; Sugai, H.; Kusano, K.; Nozawa, Y.; Yamauchi, S.; Karahashi, M.; Oshikawa, S.; Kikuchi, K.; Koshio, S.; Watanabe, K.; Suzuki, Y.

2014-01-01

Micro-PIXE analysis has been performed on two soil samples with high cesium activity concentrations. These soil samples were contaminated by fallout from the accident at Fukushima Daiichi Nuclear Power Plant. One exhibits a radioactive cesium transfer of ˜0.01, and the other shows a radioactive cesium transfer of less than 0.001, even though both samples have high cesium activity concentrations exceeding 10,000 Bq/kg. X-ray spectra and elemental images of the soil samples revealed the presence of chlorine, which can react with cesium to produce an inorganic soluble compound, and phosphorus-containing cesium-capturable organic compounds.

Equipment for collecting samples of radioactive solutions

International Nuclear Information System (INIS)

Raggenbass, A.; Fradin, J.; Joubert, G.

1958-01-01

The authors present an equipment aimed at collecting samples of fission products to perform radio-chemical analysis. As the sample must have a total activity between 1 and 50 micro-Curie, this installation comprises a sampling system and a dilution device which aims at bringing the sample to the suitable activity. Samples are collected by means of needles. The sample reproducibility is discussed. The dilution device is described

How much will afforestation of former cropland influence soil C stocks? A synthesis of paired sampling, chronosequence sampling and repeated sampling studies

Science.gov (United States)

Vesterdal, Lars; Hansen, K.; Stupak, I.; Don, Axel; Poeplau, C.; Leifeld, Jens; van Wesemael, Bas

2010-05-01

The need for documentation of land-use change effects on soil C is high on the agenda in most signatory countries to the Kyoto Protocol. Large land areas in Europe have experienced land-use change from cropland to forest since 1990 by direct afforestation as well as abandonment and regrowth of marginally productive cropland. Soil C dynamics following land-use change remain highly uncertain due to a limited number of available studies and due to influence of interacting factors such as land use history, soil type, and climate. Common approaches for estimation of potential soil C changes following land-use change are i) paired sampling of plots with a long legacy of different land uses, ii) chronosequence studies of land-use change, and lastly iii) repeated sampling of plots subject to changed land use. This paper will synthesize the quantitative effects of cropland afforestation on soil C sequestration based on all three approaches and will report on related work within Cost 639. Paired plots of forest and cropland were used to study the general differences between soil C stocks in the two land uses. At 27 sites in Denmark distributed among different regions and soil types forest floor and mineral soil were sampled in and around soil pits. Soil C stocks were higher in forest than cropland (mean difference 22 Mg C ha-1 to 1 m depth). This difference was caused solely by the presence of a forest floor in forests; mineral soil C stocks were similar (108 vs. 109 Mg C ha-1) in the two land uses regardless of soil type and the soil layers considered. The chronosequence approach was employed in the AFFOREST project for evaluation of C sequestration in biomass and soils following afforestation of cropland. Two oak (Quercus robur) and four Norway spruce (Picea abies) afforestation chronosequences (age range 1 to 90 years) were studied in Denmark, Sweden and the Netherlands. Forest floor and mineral soil (0-25 cm) C contents were as a minimum unchanged and in most cases there

New Zealand guidelines for the collection of groundwater samples for chemical and isotopic analyses

International Nuclear Information System (INIS)

Rosen, M.R.; Cameron, S.G.; Reeves, R.R.; Taylor, C.B.

1999-01-01

Chemical and isotopic analyses of groundwater are important tools for differentiating between the natural composition and human-induced contaminants of groundwater. A comprehensive suite of inorganic water chemical analyses is necessary to characterise waters. The geology of New Zealand is diverse, so it is impractical to characterise a ''typical'' groundwater chemical composition. Each aquifer system should be evaluated individually because the major dissolved species contain useful information about the pathways of water through the soil zone into the aquifer. Analyses of major ions such as chloride, nitrate, potassium and sulphate often give indication of septic systems and agricultural contamination. The minor ions, while most are not considered contaminants, are often indicators of human activity. Iron and manganese are good indicators of Eh potential, which is an important control on the mobility of many heavy metals. The inexpensive inorganic chemical analytical suite should be used as a guide to advisability of more expensive contaminant testing. The purpose of this manual is to provide consistent groundwater sampling guidelines for use throughout New Zealand. Sinton's (1998) guide to groundwater sampling techniques provided a sound basis for the accurate collection of groundwater samples. However Sinton did not address sampling materials and techniques for the collection of samples for ultra trace component analysis or the collection of environmental isotope samples. These important aspects of groundwater sampling have been included in this updated manual. (author). 30 refs., 12 figs., 5 tabs., 1 appendix

SAMPLING ADAPTIVE STRATEGY AND SPATIAL ORGANISATION ESTIMATION OF SOIL ANIMAL COMMUNITIES AT VARIOUS HIERARCHICAL LEVELS OF URBANISED TERRITORIES

Directory of Open Access Journals (Sweden)

Baljuk J.A.

2014-12-01

Full Text Available In work the algorithm of adaptive strategy of optimum spatial sampling for studying of the spatial organisation of communities of soil animals in the conditions of an urbanization have been presented. As operating variables the principal components obtained as a result of the analysis of the field data on soil penetration resistance, soils electrical conductivity and density of a forest stand, collected on a quasiregular grid have been used. The locations of experimental polygons have been stated by means of program ESAP. The sampling has been made on a regular grid within experimental polygons. The biogeocoenological estimation of experimental polygons have been made on a basis of A.L.Belgard's ecomorphic analysis. The spatial configuration of biogeocoenosis types has been established on the basis of the data of earth remote sensing and the analysis of digital elevation model. The algorithm was suggested which allows to reveal the spatial organisation of soil animal communities at investigated point, biogeocoenosis, and landscape.

Analysis of the research sample collections of Uppsala biobank.

Science.gov (United States)

Engelmark, Malin T; Beskow, Anna H

2014-10-01

Uppsala Biobank is the joint and only biobank organization of the two principals, Uppsala University and Uppsala University Hospital. Biobanks are required to have updated registries on sample collection composition and management in order to fulfill legal regulations. We report here the results from the first comprehensive and overall analysis of the 131 research sample collections organized in the biobank. The results show that the median of the number of samples in the collections was 700 and that the number of samples varied from less than 500 to over one million. Blood samples, such as whole blood, serum, and plasma, were included in the vast majority, 84.0%, of the research sample collections. Also, as much as 95.5% of the newly collected samples within healthcare included blood samples, which further supports the concept that blood samples have fundamental importance for medical research. Tissue samples were also commonly used and occurred in 39.7% of the research sample collections, often combined with other types of samples. In total, 96.9% of the 131 sample collections included samples collected for healthcare, showing the importance of healthcare as a research infrastructure. Of the collections that had accessed existing samples from healthcare, as much as 96.3% included tissue samples from the Department of Pathology, which shows the importance of pathology samples as a resource for medical research. Analysis of different research areas shows that the most common of known public health diseases are covered. Collections that had generated the most publications, up to over 300, contained a large number of samples collected systematically and repeatedly over many years. More knowledge about existing biobank materials, together with public registries on sample collections, will support research collaborations, improve transparency, and bring us closer to the goals of biobanks, which is to save and prolong human lives and improve health and quality of life.

Urine sample collection protocols for bioassay samples

Energy Technology Data Exchange (ETDEWEB)

MacLellan, J.A.; McFadden, K.M.

1992-11-01

In vitro radiobioassay analyses are used to measure the amount of radioactive material excreted by personnel exposed to the potential intake of radioactive material. The analytical results are then used with various metabolic models to estimate the amount of radioactive material in the subject`s body and the original intake of radioactive material. Proper application of these metabolic models requires knowledge of the excretion period. It is normal practice to design the bioassay program based on a 24-hour excretion sample. The Hanford bioassay program simulates a total 24-hour urine excretion sample with urine collection periods lasting from one-half hour before retiring to one-half hour after rising on two consecutive days. Urine passed during the specified periods is collected in three 1-L bottles. Because the daily excretion volume given in Publication 23 of the International Commission on Radiological Protection (ICRP 1975, p. 354) for Reference Man is 1.4 L, it was proposed to use only two 1-L bottles as a cost-saving measure. This raised the broader question of what should be the design capacity of a 24-hour urine sample kit.

Urine sample collection protocols for bioassay samples

Energy Technology Data Exchange (ETDEWEB)

MacLellan, J.A.; McFadden, K.M.

1992-11-01

In vitro radiobioassay analyses are used to measure the amount of radioactive material excreted by personnel exposed to the potential intake of radioactive material. The analytical results are then used with various metabolic models to estimate the amount of radioactive material in the subject's body and the original intake of radioactive material. Proper application of these metabolic models requires knowledge of the excretion period. It is normal practice to design the bioassay program based on a 24-hour excretion sample. The Hanford bioassay program simulates a total 24-hour urine excretion sample with urine collection periods lasting from one-half hour before retiring to one-half hour after rising on two consecutive days. Urine passed during the specified periods is collected in three 1-L bottles. Because the daily excretion volume given in Publication 23 of the International Commission on Radiological Protection (ICRP 1975, p. 354) for Reference Man is 1.4 L, it was proposed to use only two 1-L bottles as a cost-saving measure. This raised the broader question of what should be the design capacity of a 24-hour urine sample kit.

A generalized transmission method for gamma-efficiency determinations in soil samples

International Nuclear Information System (INIS)

Bolivar, J.P.; Garcia-Tenorio, R.; Garcia-Leon, M.

1994-01-01

In this paper, a generalization of the γ-ray transmission method which is useful for measurements on soil samples, for example, is presented. The correction factor, f, is given, which is a function of the apparent density of the soil and the γ-ray energy. With this method, the need for individual determinations of f, for each energy and apparent soil density is avoided. Although the method has been developed for soils, the general philosophy can be applied to other sample matrices, such as water or vegetables for example. (author)

Pilot studies for the North American Soil Geochemical Landscapes Project - Site selection, sampling protocols, analytical methods, and quality control protocols

Science.gov (United States)

Smith, D.B.; Woodruff, L.G.; O'Leary, R. M.; Cannon, W.F.; Garrett, R.G.; Kilburn, J.E.; Goldhaber, M.B.

2009-01-01

In 2004, the US Geological Survey (USGS) and the Geological Survey of Canada sampled and chemically analyzed soils along two transects across Canada and the USA in preparation for a planned soil geochemical survey of North America. This effort was a pilot study to test and refine sampling protocols, analytical methods, quality control protocols, and field logistics for the continental survey. A total of 220 sample sites were selected at approximately 40-km intervals along the two transects. The ideal sampling protocol at each site called for a sample from a depth of 0-5 cm and a composite of each of the O, A, and C horizons. The Ca, Fe, K, Mg, Na, S, Ti, Ag, As, Ba, Be, Bi, Cd, Ce, Co, Cr, Cs, Cu, Ga, In, La, Li, Mn, Mo, Nb, Ni, P, Pb, Rb, Sb, Sc, Sn, Sr, Te, Th, Tl, U, V, W, Y, and Zn by inductively coupled plasma-mass spectrometry and inductively coupled plasma-atomic emission spectrometry following a near-total digestion in a mixture of HCl, HNO3, HClO4, and HF. Separate methods were used for Hg, Se, total C, and carbonate-C on this same size fraction. Only Ag, In, and Te had a large percentage of concentrations below the detection limit. Quality control (QC) of the analyses was monitored at three levels: the laboratory performing the analysis, the USGS QC officer, and the principal investigator for the study. This level of review resulted in an average of one QC sample for every 20 field samples, which proved to be minimally adequate for such a large-scale survey. Additional QC samples should be added to monitor within-batch quality to the extent that no more than 10 samples are analyzed between a QC sample. Only Cr (77%), Y (82%), and Sb (80%) fell outside the acceptable limits of accuracy (% recovery between 85 and 115%) because of likely residence in mineral phases resistant to the acid digestion. A separate sample of 0-5-cm material was collected at each site for determination of organic compounds. A subset of 73 of these samples was analyzed for a suite of

Use of passive sampling devices to determine soil contaminant concentrations

Energy Technology Data Exchange (ETDEWEB)

Johnson, K.A. [Clemson Univ., Pendleton, SC (United States)]|[Washington State Univ., Richland, WA (United States); Hooper, M.J. [Clemson Univ., Pendleton, SC (United States); Weisskopf, C.P. [Washington State Univ., Richland, WA (United States)

1996-12-31

The effective remediation of contaminated sites requires accurate identification of chemical distributions. A rapid sampling method using passive sampling devices (PSDs) can provide a thorough site assessment. We have been pursuing their application in terrestrial systems and have found that they increase the ease and speed of analysis, decrease solvent usage and overall cost, and minimize the transport of contaminated soils. Time and cost savings allow a higher sampling frequency than is generally the case using traditional methods. PSDs have been used in the field in soils of varying physical properties and have been successful in estimating soil concentrations ranging from 1 {mu}g/kg (parts per billion) to greater than 200 mg/kg (parts per million). They were also helpful in identifying hot spots within the sites. Passive sampling devices show extreme promise as an analytical tool to rapidly characterize contaminant distributions in soil. There are substantial time and cost savings in laboratory personnel and supplies. By selectively excluding common interferences that require sample cleanup, PSDs can be retrieved from the field and processed rapidly (one technician can process approximately 90 PSDs in an 8-h work day). The results of our studies indicate that PSDs can be used to accurately estimate soil contaminant concentrations and provide lower detection limits. Further, time and cost savings will allow a more thorough and detailed characterization of contaminant distributions. 13 refs., 4 figs., 2 tabs.

Statistical sampling approaches for soil monitoring

NARCIS (Netherlands)

Brus, D.J.

2014-01-01

This paper describes three statistical sampling approaches for regional soil monitoring, a design-based, a model-based and a hybrid approach. In the model-based approach a space-time model is exploited to predict global statistical parameters of interest such as the space-time mean. In the hybrid

Isolation and Screening of Potential Cellulolytic and Xylanolytic Bacteria from Soil Sample for Degradation of Lignocellulosic Biomass

Directory of Open Access Journals (Sweden)

Bhupal Govinda Shrestha

2016-11-01

them with the aptitude to produce stable enzymes, little emphasis has been given to cellulose/xylanase production from bacteria. Seven soil samples were collected from eastern hilly districts of Nepal viz. Taplejung, Panchthar and Sankhuwasabha districts, from soil surface and at depth of 10cm to 20cm, and were isolated separately. From the seven soil samples, four bacterial isolates were obtained. Isolates (PSS, P1D, TLC, SNK were then screened for cellulolytic/xylanolytic activity using Congo red assay on Carboxymethylcellulose (CMC/xylan agar plates. The enzyme activity obtained from isolates was dependent on substrate concentration. The activity of enzymes produced by isolates were also measured and compared on pretreated sugarcane bagasse. Among those samples, the greatest zone of inhibition in both CMC (1.3 cm and xylan (1.0 cm agar media was seen in isolate P1D. It also produced the highest activity of endoglucanase and xylanase i.e. activity 0.035 U/mL and 0.050 U/mL respectively at 0.010 mg mL-1 standard substrate concentration of CMC and xylan.

28 CFR 28.12 - Collection of DNA samples.

Science.gov (United States)

2010-07-01

... Homeland Security, collecting DNA samples from: (1) Aliens lawfully in, or being processed for lawful... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Collection of DNA samples. 28.12 Section 28.12 Judicial Administration DEPARTMENT OF JUSTICE DNA IDENTIFICATION SYSTEM DNA Sample Collection...

Are There Dangerous Levels of Lead in Local Soil?

Science.gov (United States)

Pita, I.

2017-12-01

The purpose of this experiment was to show that comparing random soil samples from areas in New Orleans; the Garden District will have the highest levels of lead in soil. My Independent variable was the soil samples collected from locations in the Garden District area of New Orleans, and other locations throughout New Orleans. The control was the soil samples collected from the local playground in the New Orleans area. My dependent variable was the lead soil test kit, using ppm (parts per million) of lead to show concentration. 400 ppm + in bare soil where children play is considered dangerous hazard levels. 1,000 + ppm in all other areas is considered dangerous hazard levels. The first step to my experiment, I collected soil samples from different locations throughout the Garden District area of New Orleans. The second step to my experiment, I conducted the lead soil testing in a controlled area at home in a well ventilated room, using all the necessary safety equipment needed, I began testing a 24 hour test period and a 48 hour test period. I then collected the data from both test. The results showed that soil samples from the Garden District area compared to the other sample locations had higher lead concentrations in the soil. This backed my hypothesis when comparing soil samples from areas in New Orleans, the Garden District will have the highest lead levels. In conclusion these experiments showed that with the soil samples collected, there were higher concentrations of lead in the soil from the Garden District area compared to the other areas where soil was collected. Reconstruction and renovations, from the devastation that Hurricane Katrina created, are evident of the lead in paint of older homes which now show the lead concentration in the soil. Lead is a lethal element if consumed or inhaled in high doses, which can damage key organs in our body, which can be deadly. Better awareness through social media, television, radio, doctors, studies, pamphlets

Soil bacteria for remediation of polluted soils

Energy Technology Data Exchange (ETDEWEB)

Springael, D; Bastiaens, L; Carpels, M; Mergaey, M; Diels, L

1996-09-18

Soil bacteria, specifically adapted to contaminated soils, may be used for the remediation of polluted soils. The Flemish research institute VITO has established a collection of bacteria, which were isolated from contaminated areas. This collection includes microbacteria degrading mineral oils (Pseudomonas sp., Acinetobacter sp. and others), microbacteria degrading polycyclic aromatic hydrocarbons (genera Sphingomonas and Mycobacterium), microbacteria degrading polychlorobiphenyls (genus Ralstonia and strains related to beta-Proteobacteria), and metal resistant bacteria with plasmid borne resistances to Cd, Zn, Ni, Co, Cu, Hg, and Cr. Bench-scale reactors were developed to investigate the industrial feasibility of bioremediation. Batch Stirred Tank Reactors were used to evaluate the efficiency of oil degraders. Soils, contaminated with non-ferrous metals, were treated using a Bacterial Metal Slurry Reactor. It was found that the reduction of the Cd concentration may vary strongly from sample to sample: reduction factors vary from 95 to 50%. Is was shown that Cd contained in metallic sinter and biologically unavailable Cd could not be removed.

The standardization of an apparatus for the mixing of soil samples ...

African Journals Online (AJOL)

Quantitative determination of nematode populations in soils frequently necessitates the mixing of representative soil samples to form a homogeneous, compound sample from which the nematodes are extracted. A mixing apparatus was developed and standardized with the aid of a spectrophotometric technique by which ...

Study on vertical distribution of radionuclides ({sup 40}K, Th and U) in soil collected from Manjung district

Energy Technology Data Exchange (ETDEWEB)

Zainal, Fetri; Hamzah, Zaini; Wood, Khalik [Faculty of Sciences, Universiti Teknologi MARA, 40450, Shah Alam, Selangor (Malaysia); Saat, Ahmad [Faculty of Sciences, Universiti Teknologi MARA, 40450, Shah Alam, Selangor (Malaysia); Institute of Science, Universiti Teknologi MARA, 40450, Shah Alam, Selangor (Malaysia); Alias, Masitah [TNB Research Sdn. Bhd. 43000 Kajang, Selangor (Malaysia)

2016-01-22

The accumulation of radionuclides in soil is a greatest concerns due to their toxicity. This study investigated the vertical distribution of radionuclides and radiological assessment in a soil profile were collected in three different directions [North (N), North-East (NE) and South-East (SE)] within 40 km from Manjung district. All profile samples were collected down to 45cm at 7.5cm interval using hand auger. Soil density and radionuclides ({sup 40}K, Th and U) concentrations were determined by gravimetric method and Energy Dispersive X-Ray Fluorescence (EDXRF) technique, respectively. The radionuclides concentrations was in decreasing order of {sup 40}K > Th > U. Soil quality assessment was carried out using Enrichment Factor (EF), Pollution Index (PI) and Geoaccumulation Index (I {sub geo}) where all radionuclides show significant enrichment (5 < EF < 20), PI classified as middle pollution classes and 0 < Igeo < 1, indicating moderately polluted, respectively. From the concentration of radionuclides, the radiological risk was calculated and the present result show external hazard index (H{sub ex}) is below than unity indicate low radiological risk.

Soil map disaggregation improved by soil-landscape relationships, area-proportional sampling and random forest implementation

DEFF Research Database (Denmark)

Møller, Anders Bjørn; Malone, Brendan P.; Odgers, Nathan

implementation generally improved the algorithm’s ability to predict the correct soil class. The implementation of soil-landscape relationships and area-proportional sampling generally increased the calculation time, while the random forest implementation reduced the calculation time. In the most successful......Detailed soil information is often needed to support agricultural practices, environmental protection and policy decisions. Several digital approaches can be used to map soil properties based on field observations. When soil observations are sparse or missing, an alternative approach...... is to disaggregate existing conventional soil maps. At present, the DSMART algorithm represents the most sophisticated approach for disaggregating conventional soil maps (Odgers et al., 2014). The algorithm relies on classification trees trained from resampled points, which are assigned classes according...

Specification for soil multisensor and soil sampling cone penetrometer probes

International Nuclear Information System (INIS)

Iwatate, D.F.

1997-01-01

Specification requirements for engineering, fabrication, and performance of cone penetrometer (CP) soil multisensor and sampling probes (CP-probes) which are required to support contract procurement for services are presented. The specification provides a documented technical basis of quality assurance that is required to use the probes in an operating Hanford tank farm. The documentation cited in this specification will be incorporated into an operational fielding plan that will address all activities associated with the use of the CP-probes. The probes discussed in this specification support the Hanford Tanks Initiative AX-104 Tank Plume Characterization Sub-task. The probes will be used to interrogate soils and vadose zone surrounding tank AX-104

A stratified two-stage sampling design for digital soil mapping in a Mediterranean basin

Science.gov (United States)

Blaschek, Michael; Duttmann, Rainer

2015-04-01

The quality of environmental modelling results often depends on reliable soil information. In order to obtain soil data in an efficient manner, several sampling strategies are at hand depending on the level of prior knowledge and the overall objective of the planned survey. This study focuses on the collection of soil samples considering available continuous secondary information in an undulating, 16 km²-sized river catchment near Ussana in southern Sardinia (Italy). A design-based, stratified, two-stage sampling design has been applied aiming at the spatial prediction of soil property values at individual locations. The stratification based on quantiles from density functions of two land-surface parameters - topographic wetness index and potential incoming solar radiation - derived from a digital elevation model. Combined with four main geological units, the applied procedure led to 30 different classes in the given test site. Up to six polygons of each available class were selected randomly excluding those areas smaller than 1ha to avoid incorrect location of the points in the field. Further exclusion rules were applied before polygon selection masking out roads and buildings using a 20m buffer. The selection procedure was repeated ten times and the set of polygons with the best geographical spread were chosen. Finally, exact point locations were selected randomly from inside the chosen polygon features. A second selection based on the same stratification and following the same methodology (selecting one polygon instead of six) was made in order to create an appropriate validation set. Supplementary samples were obtained during a second survey focusing on polygons that have either not been considered during the first phase at all or were not adequately represented with respect to feature size. In total, both field campaigns produced an interpolation set of 156 samples and a validation set of 41 points. The selection of sample point locations has been done using

CHARACTERISTIC OF AIRBORNE PARTICULATE MATTER SAMPLES COLLECTED FROM TWO SEMI INDUSTRIAL SITES IN BANDUNG, INDONESIA

Directory of Open Access Journals (Sweden)

Diah Dwiana Lestiani

2013-12-01

Full Text Available Air particulate matter concentrations, black carbon as well as elemental concentrations in two semi industrial sites were investigated as a preliminary study for evaluation of air quality in these areas. Sampling of airborne particulate matter was conducted in July 2009 using a Gent stacked filter unit sampler and a total of 18 pairs of samples were collected. Black carbon was determined by reflectance measurement and elemental analysis was performed using particle induced X-ray emission (PIXE. Elements Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, Cr, Mn, Fe, Cu, Zn and As were detected. Twenty four hour PM2.5 concentration at semi industrial sites Kiaracondong and Holis ranged from 4.0 to 22.2 µg m-3, while the PM10 concentration ranged from 24.5 to 77.1 µg m-3. High concentration of crustal elements, sulphur and zinc were identified in fine and coarse fractions for both sites. The fine fraction data from both sites were analyzed using a multivariate principal component analysis and for Kiaracondong site, identified factors are attributed to sea-salt with soil dust, vehicular emissions and biomass burning, non ferrous smelter, and iron/steel work industry, while for Holis site identified factors are attributed to soil dust, industrial emissions, vehicular emissions with biomass burning, and sea-salt. Although particulate samples were collected from semi industrial sites, vehicular emissions constituted with S, Zn and BC were identified in both sites.

Microbiological evaluation on toxicity amelioration of soil samples contaminated with petroleum-based products

International Nuclear Information System (INIS)

Khairuddin Abdul Rahim; Pauline Liew Woan Ying; Ahmad Nazrul Abd Wahid; Shamsiah Abdul Rahman; Mohd Suhaimi Hamzah; Abdul Khalik Wood; Muhamat Omar

2004-01-01

Samples of soil materials from oil sludge landfarm in Melaka and petroleum sludge ready for disposal were analysed on their potentially toxic elements and compounds and their microbial population. These were compared against uncontaminated soil samples from agricultural plots and fresh crude petroleum samples obtained from an oil refinery in Kerteh, Terengganu. Enumeration and isolation of culturable microbial populations in the above samples were conducted using standard plate counts and screening methods. Populations of microorganisms from uncontaminated soils were tested on its potential to degrade petroleum derived products on contaminated soil samples and crude petroleum samples in a laboratory experiment. Microorganisms with great potential to degrade petroleum sludge will be further screened in further bioremediation studies in the field. (Author)

Determination of 36Cl in environmental samples collected in the JCO by AMS

International Nuclear Information System (INIS)

Seki, R.; Tsukuba Univ., Ibaraki; Arai, D.; Nagashima, Y.; Takahashi, T.; Matsuhiro, T.; Imanaka, T.

2003-01-01

Long-lived chlorine, 36 Cl (T 1/2 = 301,000 y) in environmental samples has been measured by the AMS system installed in Tandem Accelerator Center, University of Tsukuba. A tri-carbon-molecular 12 C 3 - pilot beam method is used to stabilize the terminal voltage of the tandem. A small amount of pure carbon graphite is well mixed into a AgCl target material for creating Cl - and 12 C 3 - in the ion source. A 36 S isobaric interference in the system is eliminated to determine 36 Cl in environmental samples by chemical procedure. Some samples containing chlorine such as soil, chemical reagents and table salt have been collected in the JCO criticality accident site and analyzed to detect neutron-induced 36 Cl. The experimental result has been compared with a theoretical calculation. (author)

Livermore Big Trees Park Soil Survey

International Nuclear Information System (INIS)

McConachie, W.A.; Failor, R.A.

1995-01-01

Lawrence Livermore National Laboratory (LLNL) will sample and analyze soil in the Big Trees Park area in Livermore, California, to determine if the initial level of plutonium (Pu) in a soil sample taken by the U.S. Environmental Protection Agency (EPA) in September 1993 can be confirmed. Nineteen samples will be collected and analyzed: 4 in the area where the initial EPA sample was taken, 2 in the nearby Arroyo Seco, 12 in scattered uncovered soil areas in the park and nearby school, and 1 from the sandbox of a nearby apartment complex. Two quality control (QC) samples (field duplicates of the preceding samples) win also be collected and analyzed. This document briefly describes the purpose behind the sampling, the sampling rationale, and the methodology

Research on self-absorption corrections for laboratory γ spectral analysis of soil samples

International Nuclear Information System (INIS)

Tian Zining; Jia Mingyan; Li Huibin; Cheng Ziwei; Ju Lingjun; Shen Maoquan; Yang Xiaoyan; Yan Ling; Fen Tiancheng

2010-01-01

Based on the calibration results of the point sources,dimensions of HPGe crystal were characterized.Linear attenuation coefficients and detection efficiencies of all kinds of samples were calculated,and the function F(μ) of φ75 mm x 25 mm sample was established. Standard surface source was used to simulate the source of different heights in the soil sample. And the function ε(h) which reflect the relationship between detection efficiencies and heights of the surface sources was determined. The detection efficiency of calibration source can be obtained by integration, F(μ) functions of soil samples established is consistent with the result of MCNP calculation code. Several φ75 mm x 25 mm soil samples were measured by the HPGe spectrometer,and the function F(μ) was used to correct the self absorption. F(μ) functions of soil samples of various dimensions can be calculated by MCNP calculation code established, and self absorption correction can be done. To verify the efficiency of calculation results, φ75 mm x 75 mm soil samples were measured. Several φ75 mm x 25 mm soil samples from aerosphere nuclear testing field was measured by the HPGe spectrometer,and the function F(μ) was used to correct the self absorption. The function F(m) was established, and the technical method which is used to correct the soil samples of unknown area is also given. The correction method of surface source greatly improves the gamma spectrum's metrical accuracy, and it will be widely applied to environmental radioactive investigation. (authors)

Strontium-90 and cesium-137 in soil

International Nuclear Information System (INIS)

1976-01-01

To determine the total deposits of fallout, Japan Chemical Analysis Center has analyzed surface soil samples collected from 30 prefectures (30 locations) by the commission of Science and Technology Agency of Japanese Government. Soil samples were collected at depths of 0 -- 5 and 5 -- 20 cm on grassland or bare surface at each sampling location. Radiochemical analysis of these samples was carried out using the method recommended by Science and Technology Agency. One-hundred gram of soil was used as one sample for analysis. Results obtained during the period from July 1974 to March 1975 are shown in a table. (J.P.N.)

X-ray spectrometry and X-ray microtomography techniques for soil and geological samples analysis

International Nuclear Information System (INIS)

Kubala-Kukuś, A.; Banaś, D.; Braziewicz, J.; Dziadowicz, M.; Kopeć, E.; Majewska, U.; Mazurek, M.; Pajek, M.; Sobisz, M.; Stabrawa, I.; Wudarczyk-Moćko, J.; Góźdź, S.

2015-01-01

A particular subject of X-ray fluorescence analysis is its application in studies of the multielemental sample of composition in a wide range of concentrations, samples with different matrices, also inhomogeneous ones and those characterized with different grain size. Typical examples of these kinds of samples are soil or geological samples for which XRF elemental analysis may be difficult due to XRF disturbing effects. In this paper the WDXRF technique was applied in elemental analysis concerning different soil and geological samples (therapeutic mud, floral soil, brown soil, sandy soil, calcium aluminum cement). The sample morphology was analyzed using X-ray microtomography technique. The paper discusses the differences between the composition of samples, the influence of procedures with respect to the preparation of samples as regards their morphology and, finally, a quantitative analysis. The results of the studies were statistically tested (one-way ANOVA and correlation coefficients). For lead concentration determination in samples of sandy soil and cement-like matrix, the WDXRF spectrometer calibration was performed. The elemental analysis of the samples was complemented with knowledge of chemical composition obtained by X-ray powder diffraction.

X-ray spectrometry and X-ray microtomography techniques for soil and geological samples analysis

Energy Technology Data Exchange (ETDEWEB)

Kubala-Kukuś, A.; Banaś, D.; Braziewicz, J. [Institute of Physics, Jan Kochanowski University, ul. Świetokrzyska 15, 25-406 Kielce (Poland); Holycross Cancer Center, ul. Artwińskiego 3, 25-734 Kielce (Poland); Dziadowicz, M.; Kopeć, E. [Institute of Physics, Jan Kochanowski University, ul. Świetokrzyska 15, 25-406 Kielce (Poland); Majewska, U. [Institute of Physics, Jan Kochanowski University, ul. Świetokrzyska 15, 25-406 Kielce (Poland); Holycross Cancer Center, ul. Artwińskiego 3, 25-734 Kielce (Poland); Mazurek, M.; Pajek, M.; Sobisz, M.; Stabrawa, I. [Institute of Physics, Jan Kochanowski University, ul. Świetokrzyska 15, 25-406 Kielce (Poland); Wudarczyk-Moćko, J. [Holycross Cancer Center, ul. Artwińskiego 3, 25-734 Kielce (Poland); Góźdź, S. [Holycross Cancer Center, ul. Artwińskiego 3, 25-734 Kielce (Poland); Institute of Public Health, Jan Kochanowski University, IX Wieków Kielc 19, 25-317 Kielce (Poland)

2015-12-01

A particular subject of X-ray fluorescence analysis is its application in studies of the multielemental sample of composition in a wide range of concentrations, samples with different matrices, also inhomogeneous ones and those characterized with different grain size. Typical examples of these kinds of samples are soil or geological samples for which XRF elemental analysis may be difficult due to XRF disturbing effects. In this paper the WDXRF technique was applied in elemental analysis concerning different soil and geological samples (therapeutic mud, floral soil, brown soil, sandy soil, calcium aluminum cement). The sample morphology was analyzed using X-ray microtomography technique. The paper discusses the differences between the composition of samples, the influence of procedures with respect to the preparation of samples as regards their morphology and, finally, a quantitative analysis. The results of the studies were statistically tested (one-way ANOVA and correlation coefficients). For lead concentration determination in samples of sandy soil and cement-like matrix, the WDXRF spectrometer calibration was performed. The elemental analysis of the samples was complemented with knowledge of chemical composition obtained by X-ray powder diffraction.

Comparison of in situ gamma soil analysis and soil sampling data for mapping 241Am and 239Pu soil concentrations at the Nevada Test Site

International Nuclear Information System (INIS)

Kirby, J.A.; Anspaugh, L.R.; Phelps, P.L.; Huckabay, G.W.; Markwell, F.; Barnes, M.

1976-01-01

Soil sampling and in situ 241 Am-gamma counting with an array of four high purity, planar, Ge detectors are compared as means of determining soil concentration contours of plutonium and their associated uncertainties. Results of this survey, which covered an area of approximately 300,000 m 2 , indicate that with one-third the number of sampling locations, the in situ gamma survey provided soil concentration contours with confidence intervals that were about one-third as wide as those obtained with soil sampling. The methods of the survey are described and a discussion of advantages and limitations of both methods is given

Comparison of in situ gamma soil analysis and soil sampling data for mapping 241Am and 239Pu soil concentrations at the Nevada Test Site

International Nuclear Information System (INIS)

Kirby, J.A.; Anspaugh, L.R.; Phelps, P.L.; Huckabay, G.W.; Markwell, F.R.; Barnes, M.G.

1977-01-01

Soil sampling and in situ 241 Am-gamma counting with an array of four high-purity, planar, Ge detectors are compared as means of determining soil concentration contours of plutonium and their associated uncertainties. Results of this survey, which covered an area of approximately 300,000 m 2 , indicate that with one-third the number of sampling locations, the in situ gamma survey provided soil concentration contours with confidence intervals that were about one-third as wide as those obtained with soil sampling. The methods of the survey are described and a discussion of advantages and limitations of both methods is given

The feasible research with measuring radon for taking the soils sample

International Nuclear Information System (INIS)

Zeng Bing, Ge Liangquan; Liu Hefan; Li Yeqiang; Zhang Jinzhao; Song Xiao'an

2010-01-01

It explains the mechanism of the separation of soil's radon. Through the designed experiment, it confirms the feasibility of measuring radon for taking the soil's sample. It determines the content of the radon and its sub field with indoor and outside through ways of the activated charcoal adsorption, the initiative suction and the diameter mark etching, also the 226 Ra. The paper indicates: it is feasible with measuring radon for taking the soil's sample, and the stability of data is that indoor data are better than outside's. The temperature, the humidity, the rainfall amount, the intensity and so on are the serious influence of the data. If you want to take a soil's sample, you must avoid the rain as far as possible, and avoid the fault zone, the belt of folded strata and complex geologic structure region, and so on. (authors)

Representativeness of soil samples collected to assess mining-related contamination of flood plains in southeast Kansas

Science.gov (United States)

Juracek, Kyle E.

2015-01-01

Historical lead and zinc mining in the Tri-State Mining District (TSMD), located in parts of southeast Kansas, southwest Missouri, and northeast Oklahoma, has resulted in a substantial ongoing input of lead and zinc to the environment (Juracek, 2006; Juracek and Becker, 2009). In response to concern about the mining-related contamination, southeast Cherokee County, Kansas, was listed on the U.S. Environmental Protection Agency’s (USEPA) National Priority List as a Superfund hazardous waste site (fig. 1). To provide some of the information needed to support remediation efforts in the Cherokee County Superfund site, a study was begun in 2009 by the U.S. Geological Survey (USGS) that was requested and funded by USEPA. As part of the study, surficial-soil sampling was used to investigate the extent and magnitude of mining-related lead and zinc contamination in the flood plains of the Spring River and several tributaries within the Superfund site. In mining-affected areas, flood-plain soils had lead and zinc concentrations that far exceeded background levels as well as probable-effects guidelines for toxic aquatic biological effects (Juracek, 2013). Lead- and zinc-contaminated flood plains are a concern, in part, because they represent a long-term source of contamination to the fluvial environment.

Inter comparison of 90Sr and 137Cs contents in biologic samples and natural U in soil samples

International Nuclear Information System (INIS)

Liu Jianfen; Zeng Guangjian; Lu Xuequan

2001-01-01

The results of the 90 Sr and 137 Cs contents in biologic samples and the natural U in soil samples obtained in a joint effort by fourteen environmental radiation laboratories in the Chinese environmental protection system were analyzed and compared. Two kinds of biologic samples and one kind of soil samples were used for inter comparison. Of which, one kind of biologic samples (biologic powder samples) and the soil samples came from the IAEA samples were environmental and the reference values were known. The another kind of biologic samples were environmental tea-leaf that were taken from a tea garden near Hangzhou. The mean values obtained by all the joined laboratories was used as the reference. The inter comparison results were expressed in terms of the deviation from the reference value. It was found that the deviation of the 90 Sr and 137 Cs contents of biologic powder samples ranged from -15.4% to 26.5% and -15.0% to 0.4%, respectively. The deviation of the natural U content ranged from -25.5% to 7.3% for the soil samples. For the tea-leaf, the 90 Sr deviation was -22.7% to 19.1%, and the 137 Cs data had a relative large scatter with a ratio of the maximum and the minimum values being about 7. It was pointed out that the analysis results offered by different laboratories might have involved system errors

The Apollo lunar samples collection analysis and results

CERN Document Server

Young, Anthony

2017-01-01

This book focuses on the specific mission planning for lunar sample collection, the equipment used, and the analysis and findings concerning the samples at the Lunar Receiving Laboratory in Texas. Anthony Young documents the collection of Apollo samples for the first time for readers of all backgrounds, and includes interviews with many of those involved in planning and analyzing the samples. NASA contracted with the U.S. Geologic Survey to perform classroom and field training of the Apollo astronauts. NASA’s Geology Group within the Manned Spacecraft Center in Houston, Texas, helped to establish the goals of sample collection, as well as the design of sample collection tools, bags, and storage containers. In this book, detailed descriptions are given on the design of the lunar sampling tools, the Modular Experiment Transporter used on Apollo 14, and the specific areas of the Lunar Rover vehicle used for the Apollo 15, 16, and 17 missions, which carried the sampling tools, bags, and other related equipment ...

Assessment of natural radioactivity levels in soil samples from some areas in Assiut, Egypt.

Science.gov (United States)

El-Gamal, Hany; Farid, M El-Azab; Abdel Mageed, A I; Hasabelnaby, M; Hassanien, Hassanien M

2013-12-01

The natural radioactivity of soil samples from Assiut city, Egypt, was studied. The activity concentrations of 28 samples were measured with a NaI(Tl) detector. The radioactivity concentrations of (226)Ra, (232)Th, and (40)K showed large variations, so the results were classified into two groups (A and B) to facilitate the interpretation of the results. Group A represents samples collected from different locations in Assiut and characterized by low activity concentrations with average values of 46.15 ± 9.69, 30.57 ± 4.90, and 553.14 ± 23.19 for (226)Ra, (232)Th, and (40)K, respectively. Group B represents samples mainly collected from the area around Assiut Thermal Power Plant and characterized by very high activity concentrations with average values of 3,803 ± 145, 1,782 ± 98, and 1,377 ± 78 for (226)Ra, (232)Th, and (40)K, respectively. In order to evaluate the radiological hazard of the natural radioactivity, the radium equivalent activity (Raeq), the absorbed dose rate (D), the annual effective dose rate (E), the external hazard index (H ex), and the annual gonadal dose equivalent (AGDE) have been calculated and compared with the internationally approved values. For group A, the calculated averages of these parameters are in good agreement with the international recommended values except for the absorbed dose rate and the AGDE values which are slightly higher than the international recommended values. However, for group B, all obtained averages of these parameters are much higher by several orders of magnitude than the international recommended values. The present work provides a background of radioactivity concentrations in the soil of Assiut.

Inter-laboratory variation in the chemical analysis of acidic forest soil reference samples from eastern North America

Science.gov (United States)

Ross, Donald S.; Bailiey, Scott W; Briggs, Russell D; Curry, Johanna; Fernandez, Ivan J.; Fredriksen, Guinevere; Goodale, Christine L.; Hazlett, Paul W.; Heine, Paul R; Johnson, Chris E.; Larson, John T; Lawrence, Gregory B.; Kolka, Randy K; Ouimet, Rock; Pare, D; Richter, Daniel D.; Shirmer, Charles D; Warby, Richard A.F.

2015-01-01

Long-term forest soil monitoring and research often requires a comparison of laboratory data generated at different times and in different laboratories. Quantifying the uncertainty associated with these analyses is necessary to assess temporal changes in soil properties. Forest soil chemical properties, and methods to measure these properties, often differ from agronomic and horticultural soils. Soil proficiency programs do not generally include forest soil samples that are highly acidic, high in extractable Al, low in extractable Ca and often high in carbon. To determine the uncertainty associated with specific analytical methods for forest soils, we collected and distributed samples from two soil horizons (Oa and Bs) to 15 laboratories in the eastern United States and Canada. Soil properties measured included total organic carbon and nitrogen, pH and exchangeable cations. Overall, results were consistent despite some differences in methodology. We calculated the median absolute deviation (MAD) for each measurement and considered the acceptable range to be the median 6 2.5 3 MAD. Variability among laboratories was usually as low as the typical variability within a laboratory. A few areas of concern include a lack of consistency in the measurement and expression of results on a dry weight basis, relatively high variability in the C/N ratio in the Bs horizon, challenges associated with determining exchangeable cations at concentrations near the lower reporting range of some laboratories and the operationally defined nature of aluminum extractability. Recommendations include a continuation of reference forest soil exchange programs to quantify the uncertainty associated with these analyses in conjunction with ongoing efforts to review and standardize laboratory methods.

Demonstration/Validation of Incremental Sampling at Two Diverse Military Ranges and Development of an Incremental Sampling Tool

Science.gov (United States)

2010-06-01

Sampling (MIS)? • Technique of combining many increments of soil from a number of points within exposure area • Developed by Enviro Stat (Trademarked...Demonstrating a reliable soil sampling strategy to accurately characterize contaminant concentrations in spatially extreme and heterogeneous...into a set of decision (exposure) units • One or several discrete or small- scale composite soil samples collected to represent each decision unit

Stability of volatile organics in environmental soil samples

Energy Technology Data Exchange (ETDEWEB)

Maskarinec, M.P.; Bayne, C.K.; Jenkins, R.A.; Johnson, L.H.; Holladay, S.K.

1992-11-01

This report focuses on data generated for the purpose of establishing the stability of 19 volatile organic compounds in environmental soil samples. The study was carried out over a 56 day (for two soils) and a 111 day (for one reference soil) time frame and took into account as many variables as possible within the constraints of budget and time. The objectives of the study were: 1) to provide a data base which could be used to provide guidance on pre-analytical holding times for regulatory purposes; and 2) to provide a basis for the evaluation of data which is generated outside of the currently allowable holding times.

More Poop, More Precision: Improving Epidemiologic Surveillance of Soil-Transmitted Helminths with Multiple Fecal Sampling using the Kato-Katz Technique.

Science.gov (United States)

Liu, Chengfang; Lu, Louise; Zhang, Linxiu; Bai, Yu; Medina, Alexis; Rozelle, Scott; Smith, Darvin Scott; Zhou, Changhai; Zang, Wei

2017-09-01

Soil-transmitted helminths, or parasitic intestinal worms, are among the most prevalent and geographically widespread parasitic infections in the world. Accurate diagnosis and quantification of helminth infection are critical for informing and assessing deworming interventions. The Kato-Katz thick smear technique, the most widely used laboratory method to quantitatively assess infection prevalence and infection intensity of helminths, has often been compared with other methods. Only a few small-scale studies, however, have considered ways to improve its diagnostic sensitivity. This study, conducted among 4,985 school-age children in an area of rural China with moderate prevalence of helminth infection, examines the effect on diagnostic sensitivity of the Kato-Katz technique when two fecal samples collected over consecutive days are examined and compared with a single sample. A secondary aim was to consider cost-effectiveness by calculating an estimate of the marginal costs of obtaining an additional fecal sample. Our findings show that analysis of an additional fecal sample led to increases of 23%, 26%, and 100% for Ascaris lumbricoides, Trichuris trichiura , and hookworm prevalence, respectively. The cost of collecting a second fecal sample for our study population was approximately USD4.60 per fecal sample. Overall, the findings suggest that investing 31% more capital in fecal sample collection prevents an underestimation of prevalence by about 21%, and hence improves the diagnostic sensitivity of the Kato-Katz method. Especially in areas with light-intensity infections of soil-transmitted helminths and limited public health resources, more accurate epidemiological surveillance using multiple fecal samples will critically inform decisions regarding infection control and prevention.

New approach to measure soil particulate organic matter in intact samples using X-ray computed micro-tomography

Science.gov (United States)

Kravchenko, Alexandra; Negassa, Wakene; Guber, Andrey; Schmidt, Sonja

2014-05-01

Particulate soil organic matter (POM) is biologically and chemically active fraction of soil organic matter. It is a source of many agricultural and ecological benefits, among which are POM's contribution to C sequestration. Most of conventional research methods for studying organic matter dynamics involve measurements conducted on pre-processed i.e., ground and sieved soil samples. Unfortunately, grinding and sieving completely destroys soil structure, the component crucial for soil functioning and C protection. Importance of a better understanding of the role of soil structure and of the physical protection that it provides to soil C cannot be overstated; and analysis of quantities, characteristics, and decomposition rates of POM in soil samples with intact structure is among the key elements of gaining such understanding. However, a marked difficulty hindering the progress in such analyses is a lack of tools for identification and quantitative analysis of POM in intact soil samples. Recent advancement in applications of X-ray computed micro-tomography (μ-CT) to soil science has given an opportunity to conduct such analyses. The objective of the current study is to develop a procedure for identification and quantitative characterization of POM within intact soil samples using X-ray μ-CT images and to test performance of the proposed procedure on a set of multiple intact soil macro-aggregates. We used 16 4-6 mm soil aggregates collected at 0-15 cm depth from a Typic Hapludalf soil at multiple field sites with diverse agricultural management history. The aggregates have been scanned at SIMBIOS Centre, Dundee, Scotland at 10 micron resolution. POM was determined from the aggregate images using the developed procedure. The procedure was based on combining image pre-processing steps with discriminant analysis classification. The first component of the procedure consisted of image pre-processing steps based on the range of gray values (GV) along with shape and size

Soil sampling and analysis plan for the Bear Creek Valley floodplain at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-11-01

This Sampling and Analysis Plan (SAP) for the Bear Creek Valley (BCV) Floodplain presents the approach and rationale for characterizing potentially contaminated soils and sediments of the Bear Creek floodplain and the impact of any contaminants on the floodplain ecosystem. It is an addendum to a previously issued document, the Remedial Investigation Work Plan for Bear Creek (Y02-S600) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee (ES/ER-19&D2), which presents background information pertaining to this floodplain investigation. The strategy presented in the SAP is to divide the investigation into three component parts: a large-scale characterization of the floodplain; a fine-scale characterization of the floodplain beginning with a known contaminated location; and a stream sediment characterization. During the large-scale and the fine-scale characterizations, soil and biota samples (i.e., small mammals, earthworms, and vegetation) will be collected in order to characterize the nature and extent of floodplain soil contamination and the impact of this contamination on floodplain biota. The fine-scale characterization will begin with an investigation of a site corresponding to the location noted in the Remedial Investigation Work Plan (ES/ER-19&D2) as an area where uranium and PCBs are concentrated in discrete strata. During this fine-scale characterization, a 1 m deep soil profile excavation will be dug into the creek berm, and individual soil strata in the excavation will be screened for alpha radiation, PCBs, and VOCs. After the laboratory analysis results are received, biota samples will be collected in the vicinity of those locations.

Preparation and application of radioactive soil samples for intercomparison

International Nuclear Information System (INIS)

Gao Zequan; Li Zhou; Li Pengxiang; Wang Ruijun; Ren Xiaona

2014-01-01

This article summarized the preparation process and intercomparison results of the simulated environmental radioactive soil samples. The components of the matrix were: SiO 2 , Al 2 O 3 , Fe 2 O 3 , MgO, CaO, NaCl, KCl and TiO 2 . All of the components were milled, oven-dried, sieved and then blended together. The homogeneity test was according to GB 15000. 5-1994, and no significant differences were observed. The 3 H analysis soils were spiked natural soils with the moisture content of 15%. Eight laboratories attended this intercomparison. The results proves that the preparation of the simulated soils were suitable for the inter-laboratories comparison. (authors)

Natural radioactivity and dose rates for soil samples around Tiruchirapalli, South India using γ-ray spectrometry

International Nuclear Information System (INIS)

Senthilkumar, Bojarajan; Manikandan, Sabapathy; Musthafa, Mohamed Saiyad

2012-01-01

The activity concentrations and the gamma-absorbed dose rates of the naturally occurring radionuclides 226 Ra, 232 Th, and 40 K were determined for 40 soil samples collected from Tiruchirapalli, South India, using γ-ray spectrometry. The average activity concentrations of 226 Ra, 232 Th, and 40 K in the soil samples were found to be 29.9, 39.0, and 369.7 Bq kg -1 , respectively. The measured activity concentrations of both 226 Ra and 40 K in the soil were lower than the world average, whereas, the activity of 232 Th was higher than the world average. The concentrations of these radionuclides were also compared with the average activity of the Indian soil. The radiological hazard index was calculated and compared with the internationally approved values. The average external absorbed gamma dose rate was observed to be 79.9 nGy h -1 , with a corresponding average annual effective dose of 97.9 mSv y -1 , which was above the world average values. The values of Ra eq and H ex were found to be within the criterion limit, whereas, the radioactivity level index (l γ ) and total gamma dose rate were above the worldwide average values. (author)

Acid leaching of heavy metals from contaminated soil collected from Jeddah, Saudi Arabia: kinetic and thermodynamics studies

Directory of Open Access Journals (Sweden)

Shorouq I. Alghanmi

2015-09-01

Full Text Available Urban soils polluted with heavy metals are of increasing concern because it is greatly affecting human health and the ecological systems. Hence, it is mandatory to understand the reasons behind this pollution and remediate the contaminated solid. The removal of heavy metals from contaminated soil samples collected from the vicinity of the sewage lake in Jeddah, Saudi Arabia, was explored. The leaching process was studied kinetically and thermodynamically for better understanding of the remediation process. The results showed that the soil samples were slightly basic in nature, and tend to be more neutral away from the main contaminated sewage lake area. The total metal content in the soil samples was measured using the aqua regia extractions by ICP-OES and the results showed that many of the heavy metals present have significant concentrations above the tolerable limits. In general, the metal concentrations at different sites indicated that the heavy metal pollution is mainly due to the sewage discharge to the lake. The results showed excellent correlation between the concentrations of Co, As, and Hg with the distance from the main contaminated area. The leaching of Co, As, and Hg using 1.0 M hydrochloric acid from the soil was studied kinetically at different temperatures and the experimental results were fitted using different kinetics models. The experimental data were best described with two-constant rate and Elovich equation kinetic models. Also, the thermodynamic study showed that the leaching process was spontaneous, endothermic and accompanied with increase in the entropy. In general, the polluted soil could be remediated successfully from the heavy metals using the acid leaching procedure in a short period of time.

Mobility of arsenic and its compounds in soil and soil solution: the effect of soil pretreatment and extraction methods.

Science.gov (United States)

Száková, J; Tlustos, P; Goessler, W; Frková, Z; Najmanová, J

2009-12-30

The effect of soil extraction procedures and/or sample pretreatment (drying, freezing of the soil sample) on the extractability of arsenic and its compounds was tested. In the first part, five extraction procedures were compared with following order of extractable arsenic portions: 2M HNO(3)>0.43 M CH(3)COOH>or=0.05 M EDTA>or=Mehlich III (0.2M CH(3)COOH+0.25 M NH(4)NO(3)+0.013 M HNO(3)+0.015 M NH(4)F+0.001 M EDTA) extraction>water). Additionally, two methods of soil solution sampling were compared, centrifugation of saturated soil and the use of suction cups. The results showed that different sample pretreatments including soil solution sampling could lead to different absolute values of mobile arsenic content in soils. However, the interpretation of the data can lead to similar conclusions as apparent from the comparison of the soil solution sampling methods (r=0.79). For determination of arsenic compounds mild extraction procedures (0.05 M (NH(4))(2)SO(4), 0.01 M CaCl(2), and water) and soil solution sampling using suction cups were compared. Regarding the real soil conditions the extraction of fresh samples and/or in situ collection of soil solution are preferred among the sample pretreatments and/or soil extraction procedures. However, chemical stabilization of the solutions should be allowed and included in the analytical procedures for determination of individual arsenic compounds.

BOREAS TE-01 SSA Soil Lab Data

Data.gov (United States)

National Aeronautics and Space Administration — ABSTRACT: This data set provides a set of soil properties for the SSA. The soil samples were collected at sets of soil pits. Major soil properties include soil...

The development of a Martian atmospheric Sample collection canister

Science.gov (United States)

Kulczycki, E.; Galey, C.; Kennedy, B.; Budney, C.; Bame, D.; Van Schilfgaarde, R.; Aisen, N.; Townsend, J.; Younse, P.; Piacentine, J.

The collection of an atmospheric sample from Mars would provide significant insight to the understanding of the elemental composition and sub-surface out-gassing rates of noble gases. A team of engineers at the Jet Propulsion Laboratory (JPL), California Institute of Technology have developed an atmospheric sample collection canister for Martian application. The engineering strategy has two basic elements: first, to collect two separately sealed 50 cubic centimeter unpressurized atmospheric samples with minimal sensing and actuation in a self contained pressure vessel; and second, to package this atmospheric sample canister in such a way that it can be easily integrated into the orbiting sample capsule for collection and return to Earth. Sample collection and integrity are demonstrated by emulating the atmospheric collection portion of the Mars Sample Return mission on a compressed timeline. The test results achieved by varying the pressure inside of a thermal vacuum chamber while opening and closing the valve on the sample canister at Mars ambient pressure. A commercial off-the-shelf medical grade micro-valve is utilized in the first iteration of this design to enable rapid testing of the system. The valve has been independently leak tested at JPL to quantify and separate the leak rates associated with the canister. The results are factored in to an overall system design that quantifies mass, power, and sensing requirements for a Martian atmospheric Sample Collection (MASC) canister as outlined in the Mars Sample Return mission profile. Qualitative results include the selection of materials to minimize sample contamination, preliminary science requirements, priorities in sample composition, flight valve selection criteria, a storyboard from sample collection to loading in the orbiting sample capsule, and contributions to maintaining “ Earth” clean exterior surfaces on the orbiting sample capsule.

Comparison of soil solution sampling techniques to assess metal fluxes from contaminated soil to groundwater.

Science.gov (United States)

Coutelot, F; Sappin-Didier, V; Keller, C; Atteia, O

2014-12-01

The unsaturated zone plays a major role in elemental fluxes in terrestrial ecosystems. A representative chemical analysis of soil pore water is required for the interpretation of soil chemical phenomena and particularly to assess Trace Elements (TEs) mobility. This requires an optimal sampling system to avoid modification of the extracted soil water chemistry and allow for an accurate estimation of solute fluxes. In this paper, the chemical composition of soil solutions sampled by Rhizon® samplers connected to a standard syringe was compared to two other types of suction probes (Rhizon® + vacuum tube and Rhizon® + diverted flow system). We investigated the effects of different vacuum application procedures on concentrations of spiked elements (Cr, As, Zn) mixed as powder into the first 20 cm of 100-cm columns and non-spiked elements (Ca, Na, Mg) concentrations in two types of columns (SiO2 sand and a mixture of kaolinite + SiO2 sand substrates). Rhizon® was installed at different depths. The metals concentrations showed that (i) in sand, peak concentrations cannot be correctly sampled, thus the flux cannot be estimated, and the errors can easily reach a factor 2; (ii) in sand + clay columns, peak concentrations were larger, indicating that they could be sampled but, due to sorption on clay, it was not possible to compare fluxes at different depths. The different samplers tested were not able to reflect the elemental flux to groundwater and, although the Rhizon® + syringe device was more accurate, the best solution remains to be the use of a lysimeter, whose bottom is kept continuously at a suction close to the one existing in the soil.

Effects of soil water saturation on sampling equilibrium and kinetics of selected polycyclic aromatic hydrocarbons.

Science.gov (United States)

Kim, Pil-Gon; Roh, Ji-Yeon; Hong, Yongseok; Kwon, Jung-Hwan

2017-10-01

Passive sampling can be applied for measuring the freely dissolved concentration of hydrophobic organic chemicals (HOCs) in soil pore water. When using passive samplers under field conditions, however, there are factors that might affect passive sampling equilibrium and kinetics, such as soil water saturation. To determine the effects of soil water saturation on passive sampling, the equilibrium and kinetics of passive sampling were evaluated by observing changes in the distribution coefficient between sampler and soil (K sampler/soil ) and the uptake rate constant (k u ) at various soil water saturations. Polydimethylsiloxane (PDMS) passive samplers were deployed into artificial soils spiked with seven selected polycyclic aromatic hydrocarbons (PAHs). In dry soil (0% water saturation), both K sampler/soil and k u values were much lower than those in wet soils likely due to the contribution of adsorption of PAHs onto soil mineral surfaces and the conformational changes in soil organic matter. For high molecular weight PAHs (chrysene, benzo[a]pyrene, and dibenzo[a,h]anthracene), both K sampler/soil and k u values increased with increasing soil water saturation, whereas they decreased with increasing soil water saturation for low molecular weight PAHs (phenanthrene, anthracene, fluoranthene, and pyrene). Changes in the sorption capacity of soil organic matter with soil water content would be the main cause of the changes in passive sampling equilibrium. Henry's law constant could explain the different behaviors in uptake kinetics of the selected PAHs. The results of this study would be helpful when passive samplers are deployed under various soil water saturations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Forensic Comparison of Soil Samples Using Nondestructive Elemental Analysis.

Science.gov (United States)

Uitdehaag, Stefan; Wiarda, Wim; Donders, Timme; Kuiper, Irene

2017-07-01

Soil can play an important role in forensic cases in linking suspects or objects to a crime scene by comparing samples from the crime scene with samples derived from items. This study uses an adapted ED-XRF analysis (sieving instead of grinding to prevent destruction of microfossils) to produce elemental composition data of 20 elements. Different data processing techniques and statistical distances were evaluated using data from 50 samples and the log-LR cost (C llr ). The best performing combination, Canberra distance, relative data, and square root values, is used to construct a discriminative model. Examples of the spatial resolution of the method in crime scenes are shown for three locations, and sampling strategy is discussed. Twelve test cases were analyzed, and results showed that the method is applicable. The study shows how the combination of an analysis technique, a database, and a discriminative model can be used to compare multiple soil samples quickly. © 2016 American Academy of Forensic Sciences.

BOREAS TE-01 SSA Soil Lab Data

Data.gov (United States)

National Aeronautics and Space Administration — This data set provides a set of soil properties for the SSA. The soil samples were collected at sets of soil pits. Major soil properties include soil horizon; dry...

Analysis on soil compressibility changes of samples stabilized with lime

Directory of Open Access Journals (Sweden)

Elena-Andreea CALARASU

2016-12-01

Full Text Available In order to manage and control the stability of buildings located on difficult foundation soils, several techniques of soil stabilization were developed and applied worldwide. Taking into account the major significance of soil compressibility on construction durability and safety, the soil stabilization with a binder like lime is considered one of the most used and traditional methods. The present paper aims to assess the effect of lime content on soil geotechnical parameters, especially on compressibility ones, based on laboratory experimental tests, for several soil categories in admixture with different lime dosages. The results of this study indicate a significant improvement of stabilized soil parameters, such as compressibility and plasticity, in comparison with natural samples. The effect of lime stabilization is related to an increase of soil structure stability by increasing the bearing capacity.

Soil arthropod fauna from natural ecosites and reclaimed oil sands soils in northern Alberta

Energy Technology Data Exchange (ETDEWEB)

Battigelli, J.P.; Leskiw, L.A. [Paragon Soil and Environmental Consulting Inc., Edmonton, AB (Canada)

2006-07-01

An understanding of soil invertebrates may facilitate current reclamation activities in the oil sands region of Alberta. This paper presented the results of a study investigating the density, diversity, and structure of soil arthropod assemblages in natural habitats and reclaimed sites. The purpose of the study was to establish a baseline inventory of soil arthropod assemblages in order to enable long-term monitoring of soil arthropod recolonization in disturbed sites. Nine natural ecosites were sampled for the study, including peat mix over secondary material over tailing sand; direct placement over tailing sand; peat mix over secondary over overburden; direct placement over overburden; peat mix over tailing sand; and peat mix over overburden. Samples were collected from previously established long-term soil and vegetation treatment plots in both natural ecosites and reclaimed soil sites located near Fort McMurray, Alberta. Results showed that densities of mesofauna were significantly higher in samples collected from natural ecosites. Acari and Collembola represented approximately 97 to 98 per cent of the fauna collected. It was also noted that the overall structure of the soil mesofauna community differed between natural soils and reclaimed soils. A significant reduction in the abundance of oribatid mites was observed in soils that had been reclaimed for over 34 years. Changes in the soil mesofauna community structure suggested that reclaimed soils continue to represent disturbed ecosites, as was indicated by higher proportions of prostigmatid mites and some collembolan families. Differences in community structure may influence soil ecosystem functions, including decomposition rates; nutrient recycling; soil structure; and fungal and bacterial biomass. It was concluded that further research is needed to examine oribatid mites and collembolan species diversity and community structure in reclaimed soils. 18 refs., 6 figs.

The U.S. Geological Survey Geologic Collections Management System (GCMS)—A master catalog and collections management plan for U.S. Geological Survey geologic samples and sample collections

Science.gov (United States)

,

2015-01-01

The U.S. Geological Survey (USGS) is widely recognized in the earth science community as possessing extensive collections of earth materials collected by research personnel over the course of its history. In 2006, a Geologic Collections Inventory was conducted within the USGS Geology Discipline to determine the extent and nature of its sample collections, and in 2008, a working group was convened by the USGS National Geologic and Geophysical Data Preservation Program to examine ways in which these collections could be coordinated, cataloged, and made available to researchers both inside and outside the USGS. The charge to this working group was to evaluate the proposition of creating a Geologic Collections Management System (GCMS), a centralized database that would (1) identify all existing USGS geologic collections, regardless of size, (2) create a virtual link among the collections, and (3) provide a way for scientists and other researchers to obtain access to the samples and data in which they are interested. Additionally, the group was instructed to develop criteria for evaluating current collections and to establish an operating plan and set of standard practices for handling, identifying, and managing future sample collections. Policies and procedures promoted by the GCMS would be based on extant best practices established by the National Science Foundation and the Smithsonian Institution. The resulting report—USGS Circular 1410, “The U.S. Geological Survey Geologic Collections Management System (GCMS): A Master Catalog and Collections Management Plan for U.S. Geological Survey Geologic Samples and Sample Collections”—has been developed for sample repositories to be a guide to establishing common practices in the collection, retention, and disposal of geologic research materials throughout the USGS.

Simultaneous determination of iodide and iodate in soil solution samples by HPLC with electrochemical detection and post-column reaction method

Energy Technology Data Exchange (ETDEWEB)

Takeda, Akira; Takaku, Yuichi; Hisamatsu, Shun' ichi [Department of Radioecology, Institute for Environmental Sciences, Aomori 039-3212 (Japan); Tsukada, Hirofumi [Department of Radioecology, Institute for Environmental Sciences, Aomori 039-3212 (Japan); Institute of Environmental Radioactivity, Fukushima University, Fukushima 960-1196 (Japan)

2014-07-01

{sup -} with ascorbic acid, and the concentration of I- was determined by the method described above. The difference between the concentration of total iodine and the sum of the I{sup -} and IO{sub 3}{sup -} concentrations was considered to be the concentration of organic iodine. Three surface soil samples collected from arable land or grassland in Rokkasho, Japan, were used as test samples. The air-dried soil samples were incubated for 21 d at 30 deg. C after addition of sufficient deionized water to obtain 60% of maximum water-holding capacity of each soil. Soil solutions were then collected after high-speed centrifugation and passed through a 0.22-μm filter. Both I{sup -} and IO{sub 3}{sup -} in a mixed standard solution were successfully detected, and analysis of one sample was completed within 10 min. Calibration curves for I{sup -} and IO{sub 3}{sup -} were linear over the ranges 0.5-25 and 1.0-50 μg-I L{sup -1}, respectively. The concentration of I{sup -} in the soil solution was 1.0-5.9 μg-I L{sup -1}, which represented 3.8%-11% of the total iodine in the solution. IO{sub 3}{sup -} was not detected in any of the soil solutions. This study was performed under contract with the government of Aomori Prefecture, Japan (authors)

Dielectrophoretic sample preparation for environmental monitoring of microorganisms: Soil particle removal.

Science.gov (United States)

Fatoyinbo, Henry O; McDonnell, Martin C; Hughes, Michael P

2014-07-01

Detection of pathogens from environmental samples is often hampered by sensors interacting with environmental particles such as soot, pollen, or environmental dust such as soil or clay. These particles may be of similar size to the target bacterium, preventing removal by filtration, but may non-specifically bind to sensor surfaces, fouling them and causing artefactual results. In this paper, we report the selective manipulation of soil particles using an AC electrokinetic microfluidic system. Four heterogeneous soil samples (smectic clay, kaolinitic clay, peaty loam, and sandy loam) were characterised using dielectrophoresis to identify the electrical difference to a target organism. A flow-cell device was then constructed to evaluate dielectrophoretic separation of bacteria and clay in a continous flow through mode. The average separation efficiency of the system across all soil types was found to be 68.7% with a maximal separation efficiency for kaolinitic clay at 87.6%. This represents the first attempt to separate soil particles from bacteria using dielectrophoresis and indicate that the technique shows significant promise; with appropriate system optimisation, we believe that this preliminary study represents an opportunity to develop a simple yet highly effective sample processing system.

Apparent soil electrical conductivity in two different soil types

Directory of Open Access Journals (Sweden)

Wilker Nunes Medeiros

Full Text Available ABSTRACT Mapping the apparent soil electrical conductivity (ECa has become important for the characterization of the soil variability in precision agriculture systems. Could the ECa be used to locate the soil sampling points for mapping the chemical and physical soil attributes? The objective of this work was to examine the relations between ECa and soil attributes in two fields presenting different soil textures. In each field, 50 sampling points were chosen using a path that presented a high variability of ECa obtained from a preliminary ECa map. At each sampling point, the ECa was measured in soil depths of 0-20, 0-40 and 0-60 cm. In addition, at each point, soil samples were collected for the determination of physical and chemical attributes in the laboratory. The ECa data obtained for different soil depths was very similar. A large number of significant correlations between ECa and the soil attributes were found. In the sandy clay loam texture field there was no correlation between ECa and organic matter or between ECa and soil clay and sand content. However, a significant positive correlation was shown for the remaining phosphorus. In the sandy loam texture field the ECa had a significant positive correlation with clay content and a significant negative correlation with sand content. The results suggest that the mapping of apparent soil electrical conductivity does not replace traditional soil sampling, however, it can be used as information to delimit regions in a field that have similar soil attributes.

Measurement of activity concentration of primordial radionuclides in the soil samples of Tiruchirappalli, Tamil Nadu, India

International Nuclear Information System (INIS)

Sadiq Bukhari, A.; Saiyad Musthafa, M.; Syed Mohamed, H.E.; Krishnamoorthy, R.; Shahul Hameed, M.M.; Shahul Hameed, P.

2008-01-01

Full text: Radioactive minerals such as uranium ( 238 U), thorium ( 232 Th) and potassium ( 40 K) are considered to be Primordial radionuclides which are widely distributed in the earth's crust. Gamma-radiation from these radionuclides represents the main external source of irradiation for the human body. Human beings are exposed outdoors to the natural terrestrial radiation that originates predominantly from the upper 30 cm of the soil. A pilot project was therefore initiated aiming at systematically measuring the terrestrial gamma radiation in Tiruchirappalli city, Tamil Nadu, South India and to establish baseline data on the terrestrial background radiation level determining its contribution to the annual effective dose equivalent to the human population. The natural radioactivity concentrations were studied in soil samples collected from 50 locations in Tiruchirappalli city. The concentration varies significantly over different soil types and the highest radioactivity was measured over soil types of granite origin followed by red soil and alluvial loam. The mean activity concentrations of 232 Th, 238 U and 40 K in soil samples are found to be 81.78 Bq.kg -1 , 32.62 Bq.kg -1 , and 551.35 Bq.kg -1 respectively. The calculated gamma dose from the soil is in the range between 38.86nGy.h -1 and 240.59 nGy.h -1 with a mean value of 89.76 nGy.h -1 . The mean annual effective dose to the population from outdoor terrestrial gamma radiation was estimated to be 0.11mSv.y -1 which is low as compared with the maximum permissible effective dose equivalent of 1mSv.y -1 (ICRP,1991). In the present study it is observed that the major sources of gamma radiation in soils are mainly derived from rocky area with granite basement. (author)

Analysis of PAH in soil samples

International Nuclear Information System (INIS)

Haeufel, J.; Weisweiler, W.

1994-01-01

The supercritical fluid extraction of polycyclic aromatic hydrocarbons (PAH) from soil samples is described. Carbon dioxide mixed with a small amount of methanol is used for solvent. The results are compared with those obtained by a classical extraction method (that means with the use of organic liquids). The extracted PAH from both procedures can be separated by HPLC and analyzed with UV- and fluorescence detection. (orig.) [de

Optimizing detection of noble gas emission at a former UNE site: sample strategy, collection, and analysis

Science.gov (United States)

Kirkham, R.; Olsen, K.; Hayes, J. C.; Emer, D. F.

2013-12-01

Underground nuclear tests may be first detected by seismic or air samplers operated by the CTBTO (Comprehensive Nuclear-Test-Ban Treaty Organization). After initial detection of a suspicious event, member nations may call for an On-Site Inspection (OSI) that in part, will sample for localized releases of radioactive noble gases and particles. Although much of the commercially available equipment and methods used for surface and subsurface environmental sampling of gases can be used for an OSI scenario, on-site sampling conditions, required sampling volumes and establishment of background concentrations of noble gases require development of specialized methodologies. To facilitate development of sampling equipment and methodologies that address OSI sampling volume and detection objectives, and to collect information required for model development, a field test site was created at a former underground nuclear explosion site located in welded volcanic tuff. A mixture of SF-6, Xe127 and Ar37 was metered into 4400 m3 of air as it was injected into the top region of the UNE cavity. These tracers were expected to move towards the surface primarily in response to barometric pumping or through delayed cavity pressurization (accelerated transport to minimize source decay time). Sampling approaches compared during the field exercise included sampling at the soil surface, inside surface fractures, and at soil vapor extraction points at depths down to 2 m. Effectiveness of various sampling approaches and the results of tracer gas measurements will be presented.

Kinetics of exchange of a tracer in soil and clay samples

Energy Technology Data Exchange (ETDEWEB)

Zanotti, J C; Facetti, J F [Asuncion Nacional Univ. (Paraguay). Inst. de Ciencias

1971-01-01

The kinetics of exchange of a Na tracer in soil and clay samples, provides with a reliable and convenient method for the determination of the different soil fraction ahd their CEC values, In addition, the analysis of the exchanges curves can be used for the identification of the clay present in the soil.

Kinetics of exchange of a tracer in soil and clay samples

International Nuclear Information System (INIS)

Zanotti, J.C.; Facetti, J.F.

1971-01-01

The kinetics of exchange of a Na tracer in soil and clay samples, provides with a reliable and convenient method for the determination of the different soil fraction ahd their CEC values, In addition, the analysis of the exchanges curves can be used for the identification of the clay present in the soil

Pore water sampling in acid sulfate soils: a new peeper method.

Science.gov (United States)

Johnston, Scott G; Burton, Edward D; Keene, Annabelle F; Bush, Richard T; Sullivan, Leigh A; Isaacson, Lloyd

2009-01-01

This study describes the design, deployment, and application of a modified equilibration dialysis device (peeper) optimized for sampling pore waters in acid sulfate soils (ASS). The modified design overcomes the limitations of traditional-style peepers, when sampling firm ASS materials over relatively large depth intervals. The new peeper device uses removable, individual cells of 25 mL volume housed in a 1.5 m long rigid, high-density polyethylene rod. The rigid housing structure allows the device to be inserted directly into relatively firm soils without requiring a supporting frame. The use of removable cells eliminates the need for a large glove-box after peeper retrieval, thus simplifying physical handling. Removable cells are easily maintained in an inert atmosphere during sample processing and the 25-mL sample volume is sufficient for undertaking multiple analyses. A field evaluation of equilibration times indicates that 32 to 38 d of deployment was necessary. Overall, the modified method is simple and effective and well suited to acquisition and processing of redox-sensitive pore water profiles>1 m deep in acid sulfate soil or any other firm wetland soils.

Parasitology and urban livestock farming in Nigeria : prevalence of ova in faecal and soil samples and animal ectoparasites in Makurdi

Directory of Open Access Journals (Sweden)

E.A. Omudu

2007-05-01

Full Text Available Domestic environmental pollution resulting from urban livestock farming was investigated in Makurdi using parasitological techniques. The test tube flotation technique was used for the parasitological analysis of animal faecal matter and soil samples collected from residential premises. Ectoparasitic fauna of dogs, goats, sheep and cattle cohabiting with humans within the same residential compound were also collected and identified. The hand-picking and body brushing methods were employed to search for ticks, fleas, lice and mites. Of the 150 soil samples examined, 55 (36.7 % were positive for 1 or more eggs of helminth parasites. There was no significant difference in the distribution of eggs in the soil samples from the 3 areas sampled (c2=0.046, df=2, P>0.05. Ascaris species were the dominant parasite eggs found. Of the 180 faecal samples examined, 107 (59.4 % were positive for 1 or more eggs of helminth parasites. Chi-square analysis showed no significant difference in the level of infection of different animal faeces sampled (c2=5.74, df=4, P>0.05. Ascaris species were again the dominating helminth parasite eggs found. There was also no significant difference in the prevalence of helminth eggs in the animal faecal samples from the 3 areas sampled (c2=5.99, df=4, P>0.05. A total of 1908 ectoparasites was recovered (ticks: 32.80 %; lice: 22.43 %; fleas: 22.06% and mite: 22.69 %. There was no significant difference in infestation animals between sexes (c2=0.10, df=4, P>0.05. The predominant genus encountered for ticks were Amblyomma, while Linognathus (43.90%, Ctenocephalides (97.38% and Sarcoptes (58.89 % were most predominant for lice, fleas and mites respectively. The public health implications of the findings, especially as these relate to the increasing incidence and prevalence of zoonotic infections, are discussed.

Evaluation of Co and Cr mobility in soil profiles collected in a scrapyard of impounded vehicles

International Nuclear Information System (INIS)

Lange, Camila N.; Figueiredo, Ana Maria G.; Enzweiler, Jacinta

2015-01-01

The number of motor vehicles in urban environments has increased dramatically in the past years. As a result, so has the number of impounded and end-of-life vehicles. Car wastes can have a very high metal content, which can cause important environmental impacts to the soil where these vehicles are kept. Most Brazilian vehicle impound scrapyards are currently operating at their maximum capacity and soils may have become contaminated by past or current vehicle handling practices. Most of these areas do not present an impermeable surface. The level of soil contamination with heavy metals depends on the type of soil, climate and management practices. Metals, such as Co and Cr, that are present in many auto-parts, may be considered potentially toxic elements in these areas. The aim of this study was to evaluate Co and Cr levels and behavior in soil profiles located in a scrapyard of impounded vehicles of Ribeirao Pires-SP city. For this purpose, samples from distinct horizons of three soil profiles were collected. Element concentrations were determined by Instrumental Neutron Activation Analysis (INAA). Soil parameters such as pH, organic matter content and clay, silt and sand percentage were also determined. The obtained data were statistically analyzed in order to establish correlations between elemental concentrations and the impounded vehicles scrapyard soil. Soil acidity showed to be the most remarkable property for Cr and Co mobility through soil profile. (author)

Evaluation of Co and Cr mobility in soil profiles collected in a scrapyard of impounded vehicles

Energy Technology Data Exchange (ETDEWEB)

Lange, Camila N.; Figueiredo, Ana Maria G., E-mail: clange@usp.br, E-mail: anamaria@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Enzweiler, Jacinta, E-mail: jacinta@ige.unicamp.br [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Instituto de Geociencias

2015-07-01

The number of motor vehicles in urban environments has increased dramatically in the past years. As a result, so has the number of impounded and end-of-life vehicles. Car wastes can have a very high metal content, which can cause important environmental impacts to the soil where these vehicles are kept. Most Brazilian vehicle impound scrapyards are currently operating at their maximum capacity and soils may have become contaminated by past or current vehicle handling practices. Most of these areas do not present an impermeable surface. The level of soil contamination with heavy metals depends on the type of soil, climate and management practices. Metals, such as Co and Cr, that are present in many auto-parts, may be considered potentially toxic elements in these areas. The aim of this study was to evaluate Co and Cr levels and behavior in soil profiles located in a scrapyard of impounded vehicles of Ribeirao Pires-SP city. For this purpose, samples from distinct horizons of three soil profiles were collected. Element concentrations were determined by Instrumental Neutron Activation Analysis (INAA). Soil parameters such as pH, organic matter content and clay, silt and sand percentage were also determined. The obtained data were statistically analyzed in order to establish correlations between elemental concentrations and the impounded vehicles scrapyard soil. Soil acidity showed to be the most remarkable property for Cr and Co mobility through soil profile. (author)

The use of gamma ray computed tomography to investigate soil compaction due to core sampling devices

International Nuclear Information System (INIS)

Pires, Luiz F.; Arthur, Robson C.J.; Correchel, Vladia; Bacchi, Osny O.S.; Reichardt, Klaus; Brasil, Rene P. Camponez do

2004-01-01

Compaction processes can influence soil physical properties such as soil density, porosity, pore size distribution, and processes like soil water and nutrient movements, root system distribution, and others. Soil porosity modification has important consequences like alterations in results of soil water retention curves. These alterations may cause differences in soil water storage calculations and matrix potential values, which are utilized in irrigation management systems. Because of this, soil-sampling techniques should avoid alterations of sample structure. In this work soil sample compaction caused by core sampling devices was investigated using the gamma ray computed tomography technique. A first generation tomograph with fixed source-detector arrangement and translation/rotational movements of the sample was utilized to obtain the images. The radioactive source is 241 Am, with an activity of 3.7 GBq, and the detector consists of a 3 in. x 3 in. NaI(Tl) scintillation crystal coupled to a photomultiplier tube. Soil samples were taken from an experimental field utilizing cylinders 4.0 cm high and 2.6 cm in diameter. Based on image analyses it was possible to detect compacted regions in all samples next to the cylinder wall due to the sampling system. Tomographic unit profiles of the sample permitted to identify higher values of soil density for deeper regions of the sample, and it was possible to determine the average densities and thickness of these layers. Tomographic analyses showed to be a very useful tool for soil compaction characterization and presented many advantages in relation to traditional methods. (author)

Molecular identification of Coccidioides spp. in soil samples from Brazil.

Science.gov (United States)

de Macêdo, Regina C L; Rosado, Alexandre S; da Mota, Fabio F; Cavalcante, Maria A S; Eulálio, Kelsen D; Filho, Antônio D; Martins, Liline M S; Lazéra, Márcia S; Wanke, Bodo

2011-05-16

Since 1991 several outbreaks of acute coccidioidomycosis (CM) were diagnosed in the semi-arid Northeast of Brazil, mainly related to disturbance of armadillo burrows caused by hunters while digging them for the capture of these animals. This activity causes dust contaminated with arthroconidia of Coccidioides posadasii, which, once inhaled, cause the mycosis. We report on the identification of C. posadasii in soil samples related to outbreaks of CM. Twenty four soil samples had their DNA extracted and subsequently submitted to a semi-nested PCR technique using specific primers. While only 6 (25%) soil samples were positive for C. posadasii by mice inoculation, all (100%) were positive by the molecular tool. This methodology represents a simple, sensitive and specific molecular technique to determine the environmental distribution of Coccidioides spp. in endemic areas, but cannot distinguish the species. Moreover, it may be useful to identify culture isolates. Key-words: 1. Coccidioidomycosis. 2. Coccidioides spp. 3. C. posadasii. 4. Semi-arid. 5. Semi-nested PCR.

76 FR 11334 - Safety Zone; Soil Sampling; Chicago River, Chicago, IL

Science.gov (United States)

2011-03-02

...The Coast Guard is establishing a temporary safety zone on the North Branch of the Chicago River near Chicago, Illinois. This zone is intended to restrict vessels from a portion of the North Branch of the Chicago River due to soil sampling in this area. This temporary safety zone is necessary to protect the surrounding public and vessels from the hazards associated with the soil sampling efforts.

Bacterial diversity of autotrophic enriched cultures from remote, glacial Antarctic, Alpine and Andean aerosol, snow and soil samples

Science.gov (United States)

González-Toril, E.; Amils, R.; Delmas, R. J.; Petit, J.-R.; Komárek, J.; Elster, J.

2009-01-01

Four different communities and one culture of autotrophic microbial assemblages were obtained by incubation of samples collected from high elevation snow in the Alps (Mt. Blanc area) and the Andes (Nevado Illimani summit, Bolivia), from Antarctic aerosol (French station Dumont d'Urville) and a maritime Antarctic soil (King George Island, South Shetlands, Uruguay Station Artigas), in a minimal mineral (oligotrophic) media. Molecular analysis of more than 200 16S rRNA gene sequences showed that all cultured cells belong to the Bacteria domain. Phylogenetic comparison with the currently available rDNA database allowed sequences belonging to Proteobacteria Alpha-, Beta- and Gamma-proteobacteria), Actinobacteria and Bacteroidetes phyla to be identified. The Andes snow culture was the richest in bacterial diversity (eight microorganisms identified) and the marine Antarctic soil the poorest (only one). Snow samples from Col du Midi (Alps) and the Andes shared the highest number of identified microorganisms (Agrobacterium, Limnobacter, Aquiflexus and two uncultured Alphaproteobacteria clones). These two sampling sites also shared four sequences with the Antarctic aerosol sample (Limnobacter, Pseudonocardia and an uncultured Alphaproteobacteriaclone). The only microorganism identified in the Antarctica soil (Brevundimonas sp.) was also detected in the Antarctic aerosol. Most of the identified microorganisms had been detected previously in cold environments, marine sediments soils and rocks. Air current dispersal is the best model to explain the presence of very specific microorganisms, like those identified in this work, in environments very distant and very different from each other.

Effect of soil and water environment on typeability of PowerPlex Y (Promega) in selected tissue samples.

Science.gov (United States)

Niemcunowicz-Janica, Anna; Pepinski, Witold; Janica, Jacek Robert; Skawronska, Malgorzata; Janica, Jerzy; Koc-Zorawska, Ewa; Stolyszewski, Ireneusz

2007-01-01

In cases of decomposed bodies Y chromosomal STR markers may be useful in identification of a male relative. The authors assessed typeability PowerPlex Y (Promega) loci in tissue material stored in water and soil environment. Tissue material was collected during autopsies of five persons aged 20-30 years with time of death determined within the limit of 14 hours. Heart muscle, liver and lung specimens were stored in pond water, sea water, sand and peat soil. DNA was extracted by organic method from tissue samples collected in 7-day intervals. Liver specimens were typeable in all PowerPlex Y loci within 100 days of storage in pond water with gradual decline at DYS392 in sea water. Heart muscle specimens stored in pond water exhibited allelic loss at DYS19, DYS385, DYS389II and DYS392, while all loci were typeable in sea water stored samples. For lung specimens allelic loss was noted throughout the profile. Storage of liver specimens in peat soil for more than 14 days resulted in allelic drop-out, and after 21 days no profiles were typeable. Heart muscle specimens were typeable in all PowerPlex Y systems after 35-day storage in sand, while allelic drop-out and subsequent lack of profiles were noted after 14 and 35 days respectively. Lung specimens stored in garden soil exhibited allelic drop-out and subsequent lack of profiles after 7 and 21 days, respectively. All PowerPlex Y loci were typeable in the latter material in sand up to day 35 with gradual decline of longer amplicons (DYS19, DYS385, DYS389II and DYS392).

Effect of soil and water environment on typeability of PowerPlex Y (Promega in selected tissue samples.

Directory of Open Access Journals (Sweden)

Ewa Koc-Zorawska

2008-01-01

Full Text Available In cases of decomposed bodies Y chromosomal STR markers may be useful in identification of a male relative. The authors assessed typeability PowerPlex Y (Promega loci in tissue material stored in water and soil environment. Tissue material was collected during autopsies of five persons aged 20-30 years with time of death determined within the limit of 14 hours. Heart muscle, liver and lung specimens were stored in pond water, sea water, sand and peat soil. DNA was extracted by organic method from tissue samples collected in 7-day intervals. Liver specimens were typeable in all PowerPlex Y loci within 100 days of storage in pond water with gradual decline at DYS392 in sea water. Heart muscle specimens stored in pond water exhibited allelic loss at DYS19, DYS385, DYS389II and DYS392, while all loci were typeable in sea water stored samples. For lung specimens allelic loss was noted throughout the profile. Storage of liver specimens in peat soil for more than 14 days resulted in allelic drop-out, and after 21 days no profiles were typeable. Heart muscle specimens were typeable in all PowerPlex Y systems after 35-day storage in sand, while allelic drop-out and subsequent lack of profiles were noted after 14 and 35 days respectively. Lung specimens stored in garden soil exhibited allelic drop-out and subsequent lack of profiles after 7 and 21 days, respectively. All PowerPlex Y loci were typeable in the latter material in sand up to day 35 with gradual decline of longer amplicons (DYS19, DYS385, DYS389II and DYS392.

Soil sampling and analysis plan for the Bear Creek Valley floodplain at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1994-11-01

This Sampling and Analysis Plan (SAP) for the Bear Creek Valley (BCV) Floodplain presents the approach and rationale for characterizing potentially contaminated soils and sediments of the Bear Creek floodplain and the impact of any contaminants on the floodplain ecosystem. It is an addendum to a previously issued document, the Remedial Investigation Work Plan for Bear Creek (Y02-S600) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee (ES/ER-19 ampersand D2), which presents background information pertaining to this floodplain investigation. The strategy presented in the SAP is to divide the investigation into three component parts: a large-scale characterization of the floodplain; a fine-scale characterization of the floodplain beginning with a known contaminated location; and a stream sediment characterization. During the large-scale and the fine-scale characterizations, soil and biota samples (i.e., small mammals, earthworms, and vegetation) will be collected in order to characterize the nature and extent of floodplain soil contamination and the impact of this contamination on floodplain biota. The fine-scale characterization will begin with an investigation of a site corresponding to the location noted in the Remedial Investigation Work Plan (ES/ER-19 ampersand D2) as an area where uranium and PCBs are concentrated in discrete strata. During this fine-scale characterization, a 1 m deep soil profile excavation will be dug into the creek berm, and individual soil strata in the excavation will be screened for alpha radiation, PCBs, and VOCs. After the laboratory analysis results are received, biota samples will be collected in the vicinity of those locations

Exchangeable phosphorus and others parameters in soil samples from Sapucai

International Nuclear Information System (INIS)

Facetti, J.F.; Zanotti, J.F.

1972-01-01

Soils samples from the alkaline rocks area at Sapucai were studied. The total amount of P in the soils shows to be high, as well as the E value for the 32 P exclangeable phosphorus. Other parameters like V values, TEC, etc., and their relationschip also were analyzed

Exchangeable phosphorus and others parameters in soil samples from Sapucai

Energy Technology Data Exchange (ETDEWEB)

Facetti, J F; Zanotti, J F [Asuncion Nacional Univ. (Paraguay). Inst. de Ciencias

1972-01-01

Soils samples from the alkaline rocks area at Sapucai were studied. The total amount of P in the soils shows to be high, as well as the E value for the 32 P exclangeable phosphorus. Other parameters like V values, TEC, etc., and their relationschip also were analyzed.

Mobility, bioavailability, and toxic effects of cadmium in soil samples

International Nuclear Information System (INIS)

Prokop, Z.; Cupr, P.; Zlevorova-Zlamalikova V.; Komarek, J.; Dusek, L.; Holoubek, I.

2003-01-01

Total concentration is not a reliable indicator of metal mobility or bioavailability in soils. The physicochemical form determines the behavior of metals in soils and hence the toxicity toward terrestrial biota. The main objectives of this study were the application and comparison of three approaches for the evaluation of cadmium behavior in soil samples. The mobility and bioavailability of cadmium in five selected soil samples were evaluated using equilibrium speciation (Windermere humic aqueous mode (WHAM)), extraction procedures (Milli-Q water, DMSO, and DTPA), and a number of bioassays (Microtox, growth inhibition test, contact toxicity test, and respiration). The mobility, represented by the water-extractable fraction corresponded well with the amount of cadmium in the soil solution, calculate using the WHAM (r 2 =0.96, P<0.001). The results of the ecotoxicologica evaluation, which represent the bioavailable fraction of cadmium, correlated well with DTPA extractability and also with the concentration of free cadmium ion, which is recognized as the most bioavailable metal form. The results of the WHAM as well as the results of extraction experiments showed a strong binding of cadmium to organic matter and a weak sorption of cadmium to clay minerals

Determination of pyridine in soil and water samples of a polluted area

International Nuclear Information System (INIS)

Peters, R.J.B.; Renesse van Duivenbode, J.A.D. van

1994-01-01

A method for the analyses of pyridine in environmental samples is described. For soil samples a distillation procedure followed by an extraction, an acidic extraction or a Soxhlet extraction can be used. For water samples a distillation procedure followed by extraction can be employed. Deuterated pyridine is used as an internal standard and the extracts are analyzed by GC-MS. The recoveries of the methods are higher than 80%; the detection limits for pyridine are 0.01 mg/kg for soil samples and 0.2 μg/l for water samples. (orig.)

A Technical Design Approach to Soil Moisture Content Measurement

African Journals Online (AJOL)

Soil moisture is an important type of data in many fields; ranging from agriculture to environmental monitoring. Three soil samples were collected at definite proportions to represent the three basic soil types (sandy, loamy and clay soils). The moisture contents of these soil samples were analyzed using the thermogravimetric ...

A survey of gross alpha and gross beta activity in soil samples in Kinta District, Perak, Malaysia

International Nuclear Information System (INIS)

Lee, Siak Kuan; Wagiran, Husin; Ramli, Ahmad Termizi

2014-01-01

The objective of this study was to determine the gross alpha and gross beta activity concentrations from the different soil types found in the Kinta District, Perak, Malaysia. A total of 128 soil samples were collected and their dose rates were measured 1 m above the ground. Gross alpha and gross beta activity measurements were carried out using gas flow proportional counter, Tennelec Series 5 LB5500 Automatic Low Background Counting System. The alpha activity concentration ranged from 15 to 9634 Bq kg -1 with a mean value of 1558±121 Bq kg -1 . The beta activity concentration ranged from 142 to 6173 Bq kg -1 with a mean value of 1112±32 Bq kg -1 . High alpha and beta activity concentrations are from the same soil type. The results of the analysis show a strong correlation between the gross alpha activity concentration and dose rate (R = 0.92). The data obtained can be used as a database for each soil type. (authors)

Environmental pollution with soil-transmitted helminths in Sanliurfa, Turkey

Directory of Open Access Journals (Sweden)

Ulukanligil Mustafa

2001-01-01

Full Text Available Soil transmitted helminth (STH infection are endemic in developing countries. A study was carried out of sewage farms, streams and vegetables to determine the sources and routes of STH infection in Sanliurfa, Turkey. Stool samples from farmhouse inhabitants as well as soil and vegetable samples from the gardens were collected and examined. In addition, water samples from streams and vegetable samples from the city market were collected and examined. One hundred and eighty-seven (59.5% of a total of 314 samples, including 88.4% of the stool samples, 60.8% of the water samples, 84.4% of the soil samples and 14% of the vegetable samples, were found to be positive for STH eggs. These results indicate that the water, soil and vegetables are heavily contaminated, and suggest a vicious circle between humans and the environment. Improving environmental sanitation is imperative for the control of soil-transmitted helminthiasis in Sanliurfa.

Sampling and analysis of alien materials in soil

Energy Technology Data Exchange (ETDEWEB)

Liphard, K G

1987-02-01

For the determination of alien materials in soil, sampling is the decisive step. After minute planning, samples can be obtained by probing, boring or abrasion. Some types of substances can be verified by advance sampling, partly already in the field. Inorganic substances present as anions or cations are eluted and determined with water, heavy metals are determined after preparing a number of solutions by spectroscopic methods. Organic alien substances are extracted with solvents and, as a rule, analysed by chromatography.

Sampling and chemical analysis in environmental samples around Nuclear Power Plants and some environmental samples

Energy Technology Data Exchange (ETDEWEB)

Cho, Yong Woo; Han, Man Jung; Cho, Seong Won; Cho, Hong Jun; Oh, Hyeon Kyun; Lee, Jeong Min; Chang, Jae Sook [KORTIC, Taejon (Korea, Republic of)

2002-12-15

Twelve kinds of environmental samples such as soil, seawater, underground water, etc. around Nuclear Power Plants(NPPs) were collected. Tritium chemical analysis was tried for the samples of rain water, pine-needle, air, seawater, underground water, chinese cabbage, a grain of rice and milk sampled around NPPs, and surface seawater and rain water sampled over the country. Strontium in the soil that sere sampled at 60 point of district in Korea were analyzed. Tritium were sampled at 60 point of district in Korea were analyzed. Tritium were analyzed in 21 samples of surface seawater around the Korea peninsular that were supplied from KFRDI(National Fisheries Research and Development Institute). Sampling and chemical analysis environmental samples around Kori, Woolsung, Youngkwang, Wooljin Npps and Taeduk science town for tritium and strontium analysis was managed according to plans. Succeed to KINS after all samples were tried.

Soil moisture variability across different scales in an Indian watershed for satellite soil moisture product validation

KAUST Repository

Singh, Gurjeet; Panda, Rabindra K.; Mohanty, Binayak P.; Jana, Raghavendra Belur

2016-01-01

Strategic ground-based sampling of soil moisture across multiple scales is necessary to validate remotely sensed quantities such as NASA’s Soil Moisture Active Passive (SMAP) product. In the present study, in-situ soil moisture data were collected

Analysis of arsenic and calcium in soil samples by laser ablation mass spectrometry

International Nuclear Information System (INIS)

Beccaglia, Ana M.; Rinaldi, Carlos A.; Ferrero, Juan C.

2006-01-01

We present an analytical procedure based on laser ablation mass spectrometry (LAMS) in order to detect and quantify arsenic and calcium in soil samples and we analyze the diverse factors that influence the precision of LAMS, such as laser fluence and matrix effect. The results indicate that a Zn matrix is a good choice for the analysis of those metals in soil samples. This work also provides a method for the direct determination of As in soil samples whose concentrations are lower than 100 ppm with a 70 ppm minimum detection limits (MDL)

Extraction and analysis of 14C-carbofuran radioactivity in soil sample

International Nuclear Information System (INIS)

Maizatul Akmam Mhd Nasir; Nashriyah Mat

2005-01-01

Carbofuran insecticide or nematicide sprayed onto soil in the agroecosystem will be taken up by plant. Carbofuran residue will pollute the environment and organisms in the food chain. Extraction and analysis of 14 C-carbofuran in soil from lysimeter were carried out. The Liquid Scintillation Counter (LSC) was used to measure radioactivity of 14 C-carbofuran in soil sample. (Author)

SOIL FERTILITY EVALUATION FOR FERTILISER RECOMMENDATION USING HYPERION DATA

Directory of Open Access Journals (Sweden)

Ranendu Ghosh

2015-12-01

Full Text Available Soil fertility characterised by nitrogen, phosphorus, potassium, calcium, magnesium and sulphur is traditionally measured from soil samples collected from the field. The process is very cumbersome and time intensive. Hyperspectral data available from Hyperion payload of EO 1 was used for facilitating preparation of soil fertility map of Udaipur district of Rajasthan state, India. Hyperion data was pre-processed for band and area sub setting, atmospheric correction and reflectance data preparation. Spectral analysis in the form of SFF and PPI were carried out for selecting the ground truth sites for soil sample collection. Soil samples collected from forty one sites were analysed for analysis of nutrient composition. Generation of correlogram followed by multiple regressions was done for identifying the most important bands and spectral parameters that can be used for nutrient map generation.

Solubility of Heavy Metals/Metalloid on Multi-Metal Contaminated Soil Samples from a Gold Ore Processing Area: Effects of Humic Substances

Directory of Open Access Journals (Sweden)

Cácio Luiz Boechat

2016-01-01

Full Text Available ABSTRACT Bioavailability of heavy metals at contaminated sites is largely controlled by the physicochemical properties of the environmental media such as dissolved organic matter, hydroxides and clay colloids, pH, soil cation exchange capacity and oxidation-reduction potential. The aim of this study was to investigate soil pH and heavy metal solubility effect by levels of humic and fulvic acids applied in soil samples with different levels of contamination by heavy metals. The soil samples used in this study were collected in a known metal-contaminated site. Humic acid (HA and fulvic acid (FA were purchased as a commercially available liquid material extracted from Leonardite. The experiment was carried out in a factorial scheme of 4 × (4 + 1, with four contaminated soil samples and four treatments, comprised of two levels of HA, two levels of FA and a control. The HA treatments increased the solubility of Cu, Zn, Ni, Cr, Cd, Pb, As and Ba from soils, while FA treatments decreased, thus raising or not their availability and mobility in soil. Humic acid concentration did not influence soil pH and FA decreased soil pH until 0.7 units. The initial heavy metal concentration in soil affects the magnitude of the processes involving humic substances. The lower releases of heavy metals by FA verified the importance of the complexation properties of organic compounds. These results appear to encourage the use of HA for increased plant-availability of heavy metals in remediation projects and the use of FA for decreased plant-availability of heavy metals at contaminated sites with a risk of introducing metals into the food chain.

A New Approach To Soil Sampling For Risk Assessment Of Nutrient Mobilisation.

Science.gov (United States)

Jonczyk, J. C.; Owen, G. J.; Snell, M. A.; Barber, N.; Benskin, C.; Reaney, S. M.; Haygarth, P.; Quinn, P. F.; Barker, P. A.; Aftab, A.; Burke, S.; Cleasby, W.; Surridge, B.; Perks, M. T.

2016-12-01

Traditionally, risks of nutrient and sediment losses from soils are assessed through a combination of field soil nutrient values on soil samples taken over the whole field and the proximity of the field to water courses. The field average nutrient concentration of the soil is used by farmers to determine fertiliser needs. These data are often used by scientists to assess the risk of nutrient losses to water course, though are not really `fit' for this purpose. The Eden Demonstration Test Catchment (http://www.edendtc.org.uk/) is a research project based in the River Eden catchment, NW UK, with the aim of cost effectively mitigating diffuse pollution from agriculture whilst maintaining agricultural productivity. Three instrumented focus catchments have been monitored since 2011, providing high resolution in-stream chemistry and ecological data, alongside some spatial data on soils, land use and nutrient inputs. An approach to mitigation was demonstrated in a small sub-catchment, where surface runoff was identified as the key drivers of nutrient losses, using a suite of runoff attenuation features. Other issues identified were management of hard- standings and soil compaction. A new approach for evaluating nutrient losses from soils is assessed in the Eden DTC project. The Sensitive Catchment Integrated Modelling and Prediction (SCIMAP) model is a risk-mapping framework designed to identify where in the landscape diffuse pollution is most likely to be originating (http://www.scimap.org.uk) and was used to look at the spatial pattern of erosion potential. The aim of this work was to assess if erosion potential identified through the model could be used to inform a new soil sampling strategy, to better assess risk of erosion and risk of transport of sediment-bound phosphorus. Soil samples were taken from areas with different erosion potential. The chemical analysis of these targeted samples are compared to those obtained using more traditional sampling approaches

Natural radioactivity in soils from Piracicaba, SP (Brazil)

International Nuclear Information System (INIS)

Oliveira, H. de.

1988-01-01

Using high resolution gamma spectrometry, the specific radioactivity of soils and rocks from Piracicaba, SP (Brazil) was determined. For this purpose, the Ra, Th and Ac natural series and some other nuclides such as sup(40)K and sup(137)Cs were considered. Soil samples representing the main Soil Groups were collected at 60-cm depth. Typical rock samples were also collected. After initial sample preparation, the sealed sample were allowed to rest until reaching the conditions approaching the secular equilibrium. Thereafter, counting was carried out, peak areas being the measurements basis. The mean ponderated values for soil specific activity were 24.1 and 34.8 Bq.kg sup(-1) for the sup(226)Ra and sup(232)Th, respectively. (author)

Molecular identification of Coccidioides spp. in soil samples from Brazil

Directory of Open Access Journals (Sweden)

Filho Antônio D

2011-05-01

Full Text Available Abstract Background Since 1991 several outbreaks of acute coccidioidomycosis (CM were diagnosed in the semi-arid Northeast of Brazil, mainly related to disturbance of armadillo burrows caused by hunters while digging them for the capture of these animals. This activity causes dust contaminated with arthroconidia of Coccidioides posadasii, which, once inhaled, cause the mycosis. We report on the identification of C. posadasii in soil samples related to outbreaks of CM. Results Twenty four soil samples had their DNA extracted and subsequently submitted to a semi-nested PCR technique using specific primers. While only 6 (25% soil samples were positive for C. posadasii by mice inoculation, all (100% were positive by the molecular tool. Conclusion This methodology represents a simple, sensitive and specific molecular technique to determine the environmental distribution of Coccidioides spp. in endemic areas, but cannot distinguish the species. Moreover, it may be useful to identify culture isolates. Key-words: 1. Coccidioidomycosis. 2. Coccidioides spp. 3. C. posadasii. 4. Semi-arid. 5. Semi-nested PCR

Bio indication of soil samples from contaminated military sites in Georgia

International Nuclear Information System (INIS)

Zakariadze, N.; Gagelidze, N.; Amiranashvili, L.; Nabakhtiani, G.; Tsigroshvili, Z.

2005-01-01

of single element's several parameters (multi-parameter bio-indication) makes possible to determine more precisely state of system under different impacts. Except study of soil samples collected on contaminated territories with an aim of low doses radiation impact (2.3 - 5.5 μZv/h) investigation on soil micro-flora in dynamics, it was decided as well to carry out experiments in earlier determined laboratory conditions in vitro by modeling the real fixed cases. The following changes of microorganisms' phenotype parameters were observed under radioactive impacts of low intensity: 1. General CCU values alternation (attenuation under 226 Ra and increase under 90 Sr); 2. Considerable increase of Bacteria colonies (Citrobacter) diameter ( 226 Ra); 3. Altered biological composition - In control sample percentage ratio of microorganisms main groups (Bacteria, Actinomycetes and Microphyte Fungi - 85/13/2) is typical to Black Earth soils. In contaminated soil this ratio is changed - 52/45/3; 4. Increased CCU and MF of Actinomycetes with melanin pigmentation and carotene synthesizing Bacteria colonies; 5. Attenuation and disappearance of Microphyte Fungi; 6. Altered vegetative and spore forms correlation of Bacillus genus, which depends on time of irradiation and effective equivalent doze obtained. Under high doze of irradiation prevalence of spore forms is observed. On application of gradually increasing doze of irradiation this correlation is approximately 1:1. The results of experiments indicate that under radioactive impacts of low intensity regulatory capacity of soil micro flora system is provided and could be maintained by changes of microorganisms separate parameters regulation. The model of microorganisms different variables behavior will be suggested. (authors)

Soil Sampling to Demonstrate Compliance with Department of Energy Radiological Clearance Requirements for the ALE Unit of the Hanford Reach National Monument

Energy Technology Data Exchange (ETDEWEB)

Fritz, Brad G.; Dirkes, Roger L.; Napier, Bruce A.

2007-04-01

The Hanford Reach National Monument consists of several units, one of which is the Fitzner/Eberhardt Arid Lands Ecology Reserve (ALE) Unit. This unit is approximately 311 km2 of shrub-steppe habitat located to the south and west of Highway 240. To fulfill internal U. S. Department of Energy (DOE) requirements prior to any radiological clearance of land, DOE must evaluate the potential for residual radioactive contamination on this land and determine compliance with the requirements of DOE Order 5400.5. Historical soil monitoring conducted on ALE indicated soil concentrations of radionuclides were well below the Authorized Limits. However, the historical sampling was done at a limited number of sampling locations. Therefore, additional soil sampling was conducted to determine if the concentrations of radionuclides in soil on the ALE Unit were below the Authorized Limits. This report contains the results of 50 additional soil samples. The 50 soil samples collected from the ALE Unit all had concentrations of radionuclides far below the Authorized Limits. The average concentrations for all detectable radionuclides were less than the estimated Hanford Site background. Furthermore, the maximum observed soil concentrations for the radionuclides included in the Authorized Limits would result in a potential annual dose of 0.14 mrem assuming the most probable use scenario, a recreational visitor. This potential dose is well below the DOE 100-mrem per year dose limit for a member of the public. Spatial analysis of the results indicated no observable statistically significant differences between radionuclide concentrations across the ALE Unit. Furthermore, the results of the biota dose assessment screen, which used the ResRad Biota code, indicated that the concentrations of radionuclides in ALE Unit soil pose no significant health risk to biota.

Assessment of pesticide contamination in soil samples from an intensive horticulture area, using ultrasonic extraction and gas chromatography-mass spectrometry.

Science.gov (United States)

Gonçalves, C; Alpendurada, M F

2005-03-15

In order to reduce the amount of sample to be collected and the time consumed in the analytical process, a broad range of analytes should be preferably considered in the same analytical procedure. A suitable methodology for pesticide residue analysis in soil samples was developed based on ultrasonic extraction (USE) and gas chromatography-mass spectrometry (GC-MS). For this study, different classes of pesticides were selected, both recent and old persistent molecules: parent compounds and degradation products, namely organochlorine, organophosphorous and pyrethroid insecticides, triazine and acetanilide herbicides and other miscellaneous pesticides. Pesticide residues could be detected in the low- to sub-ppb range (0.05-7.0mugkg(-1)) with good precision (7.5-20.5%, average 13.7% R.S.D.) and extraction efficiency (69-118%, average 88%) for the great majority of analytes. This methodology has been applied in a monitoring program of soil samples from an intensive horticulture area in Póvoa de Varzim, North of Portugal. The pesticides detected in four sampling programs (2001/2002) were the following: lindane, dieldrin, endosulfan, endosulfan sulfate, 4,4'-DDE, 4,4'-DDD, atrazine, desethylatrazine, alachlor, dimethoate, chlorpyrifos, pendimethalin, procymidone and chlorfenvinphos. Pesticide contamination was investigated at three depths and in different soil and crop types to assess the influence of soil characteristics and trends over time.

Concordance analysis of methylation biomarkers detection in self-collected and physician-collected samples in cervical neoplasm

International Nuclear Information System (INIS)

Chang, Cheng-Chang; Huang, Rui-Lan; Liao, Yu-Ping; Su, Po-Hsuan; Hsu, Yaw-Wen; Wang, Hui-Chen; Tien, Chau-Yang; Yu, Mu-Hsien; Lin, Ya-Wen; Lai, Hung-Cheng

2015-01-01

Non-attendance at gynecological clinics is a major limitation of cervical cancer screening and self-collection of samples may improve this situation. Although HPV testing of self-collected vaginal samples is acceptable, the specificity is inadequate. The current focus is increasing self-collection of vaginal samples to minimize clinic visits. In this study, we analyzed the concordance and clinical performance of DNA methylation biomarker (PAX1, SOX1, and ZNF582) detection in self-collected vaginal samples and physician-collected cervical samples for the identification of cervical neoplasm. We enrolled 136 cases with paired methylation data identified from abnormal Pap smears (n = 126) and normal controls (n = 10) regardless of HPV status at gynecological clinics. The study group comprised 37 cervical intraepithelial neoplasm I (CIN1), 23 cervical intraepithelial neoplasm II (CIN2), 16 cervical intraepithelial neoplasm III (CIN3), 30 carcinoma in situ (CIS), 13 squamous cell carcinomas (SCCs) and seven adenocarcinomas (ACs)/adenosquamous carcinomas (ASCs). PAX1, SOX1 and ZNF582 methylation in study samples was assessed by real-time quantitative methylation-specific polymerase chain reaction analysis. We generated methylation index cutoff values for the detection of CIN3+ in physician-collected cervical samples for analysis of the self-collected group. Concordance between the physician-collected and self-collected groups was evaluated by Cohen’s Kappa. Sensitivity, specificity and area under curve (AUC) were calculated for detection of CIN3+ lesions. Finally, we produced an optimal cutoff value with the best sensitivity from the self-collected groups. We generated a methylation index cutoff value from physician-collected samples for detection of CIN3+. There were no significant differences in sensitivity, specificity of PAX1, SOX1 and ZNF582 between the self-collected and physician-collected groups. The methylation status of all three genes in the normal control

Direct determination of tellurium in soil and plant samples by sector-field ICP-MS for the study of soil-plant transfer of radioactive tellurium subsequent to the Fukushima Daiichi Nuclear Power Plant accident

International Nuclear Information System (INIS)

Yang, Guosheng; Zheng, Jian; Tagami, Keiko; Uchida, Shigeo

2013-01-01

The Fukushima Daiichi Nuclear Power Plant (FDNPP) accident caused the release of large amounts of radioactive Te into the environment. Stable Te, as an analogue, is considered to be useful for the estimation of the soil-plant transfer of radioactive Te. It is necessary to estimate the radiation dose of Te that would result from food ingestion. However, due to the extremely low concentrations of Te in the environment, reported transfer factor values for Te are considerably limited. We report a sensitive analytical method for direct determination of trace Te in soil and plant samples using a sector-field inductively coupled plasma mass spectrometry (SF-ICP-MS). The developed analytical method is characterized by a very low detection limit at the sub-parts per billion (ng g"-"1) level in soil and plant samples, and it has been applied to the study of soil-plant transfer to collect transfer factor data in Japan. (author)

Poly-use multi-level sampling system for soil-gas transport analysis in the vadose zone.

Science.gov (United States)

Nauer, Philipp A; Chiri, Eleonora; Schroth, Martin H

2013-10-01

Soil-gas turnover is important in the global cycling of greenhouse gases. The analysis of soil-gas profiles provides quantitative information on below-ground turnover and fluxes. We developed a poly-use multi-level sampling system (PMLS) for soil-gas sampling, water-content and temperature measurement with high depth resolution and minimal soil disturbance. It is based on perforated access tubes (ATs) permanently installed in the soil. A multi-level sampler allows extraction of soil-gas samples from 20 locations within 1 m depth, while a capacitance probe is used to measure volumetric water contents. During idle times, the ATs are sealed and can be equipped with temperature sensors. Proof-of-concept experiments in a field lysimeter showed good agreement of soil-gas samples and water-content measurements compared with conventional techniques, while a successfully performed gas-tracer test demonstrated the feasibility of the PMLS to determine soil-gas diffusion coefficients in situ. A field application of the PMLS to quantify oxidation of atmospheric CH4 in a field lysimeter and in the forefield of a receding glacier yielded activity coefficients and soil-atmosphere fluxes well in agreement with previous studies. With numerous options for customization, the presented tool extends the methodological choices to investigate soil-gas transport in the vadose zone.

Radiological results for samples collected on paired glass- and cellulose-fiber filters at the Sandia complex, Tonopah Test Range, Nevada

International Nuclear Information System (INIS)

Mizell, Steve A.; Shadel, Craig A.

2016-01-01

Airborne particulates are collected at U.S. Department of Energy sites that exhibit radiological contamination on the soil surface to help assess the potential for wind to transport radionuclides from the contamination sites. Collecting these samples was originally accomplished by drawing air through a cellulose-fiber filter. These filters were replaced with glass-fiber filters in March 2011. Airborne particulates were collected side by side on the two filter materials between May 2013 and May 2014. Comparisons of the sample mass and the radioactivity determinations for the side-by-side samples were undertaken to determine if the change in the filter medium produced significant results. The differences in the results obtained using the two filter types were assessed visually by evaluating the time series and correlation plots and statistically by conducting a nonparametric matched-pair sign test. Generally, the glass-fiber filters collect larger samples of particulates and produce higher radioactivity values for the gross alpha, gross beta, and gamma spectroscopy analyses. However, the correlation between the radioanalytical results for the glass-fiber filters and the cellulose-fiber filters was not strong enough to generate a linear regression function to estimate the glass-fiber filter sample results from the cellulose-fiber filter sample results.

Correlation between soil chemical characteristics and soil-borne mycoflora in cucumber tunnels

International Nuclear Information System (INIS)

Qudsia, H.; Javaid, A.; Mahmood, R.; Akhtar, N.

2017-01-01

Twelve soil samples were collected from fields of cucumber (Cucumis sativus L.) tunnels from various localities of Lahore and Shekhupura districts, Pakistan. Soil samples were analyzed for various characteristics viz. pH, EC/sub e/, organic matter, nitrogen (N), phosphorus (P) and potassium (K). Soil mycoflora was isolated using dilution plate method. Soil pH, EC/sub e/, organic matter, N, P and K were in the range of 7.42-8.13, 107-2520 (meu S cm-1), 0.98-1.40%, 0.039-0.070%, 7-357 mg kg/sup -1/ and 88-946 mg kg/sup -1/ in different soil samples, respectively. A total of 18 fungal species belonging to 10 genera viz. Aspergillus, Alternaria, Cladosporium, Drechslera, Emericella, Fusarium, Mortierella, Mucor, Penicillium and Sclerotium were isolated from various soil samples. Saprophytic fungi were more prevalent than pathogenic ones. Number of colonies of saprophytic fungi ranged from 360-2754 g/sup -1/ soil in different samples. In contrast, number of pathogenic fungal colonies were limited to 1-234 g/sup -1/ soil. Number of colonies of pathogenic fungi were positively and significantly correlated with soil organic matter and nitrogen contents. This study concludes that high nitrogen and organic matter in cucumber tunnels favour population of pathogenic fungi. (author)

GEMAS: Colours of dry and moist agricultural soil samples of Europe

Science.gov (United States)

Klug, Martin; Fabian, Karl; Reimann, Clemens

2016-04-01

High resolution HDR colour images of all Ap samples from the GEMAS survey were acquired using a GeoTek Linescan camera. Three measurements of dry and wet samples with increasing exposure time and increasing illumination settings produced a set of colour images at 50μm resolution. Automated image processing was used to calibrate the six images per sample with respect to the synchronously measured X-Rite colorchecker chart. The calibrated images were then fit to Munsell soil colours that were measured in the same way. The results provide overview maps of dry and moist European soil colours. Because colour is closely linked to iron mineralogy, carbonate, silicate and organic carbon content the results can be correlated to magnetic, mineralogical, and geochemical properties. In combination with the full GEMAS chemical and physical measurements, this yields a valuable data set for calibration and interpretation of visible satellite colour data with respect to chemical composition and geological background, soil moisture, and soil degradation. This data set will help to develop new methods for world-wide characterization and monitoring of agricultural soils which is essential for quantifying geologic and human impact on the critical zone environment. It furthermore enables the scientific community and governmental authorities to monitor consequences of climatic change, to plan and administrate economic and ecological land use, and to use the data set for forensic applications.

Intrinsic and induced isoproturon catabolic activity in dissimilar soils and soils under dissimilar land use.