WorldWideScience

Sample records for software simulation systems

  1. Visual software system for memory interleaving simulation

    Directory of Open Access Journals (Sweden)

    Milenković Katarina

    2017-01-01

    Full Text Available This paper describes the visual software system for memory interleaving simulation (VSMIS, implemented for the purpose of the course Computer Architecture and Organization 1, at the School of Electrical Engineering, University of Belgrade. The simulator enables students to expand their knowledge through practical work in the laboratory, as well as through independent work at home. VSMIS gives users the possibility to initialize parts of the system and to control simulation steps. The user has the ability to monitor simulation through graphical representation. It is possible to navigate through the entire hierarchy of the system using simple navigation. During the simulation the user can observe and set the values of the memory location. At any time, the user can reset the simulation of the system and observe it for different memory states; in addition, it is possible to save the current state of the simulation and continue with the execution of the simulation later. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. III44009

  2. Physics detector simulation facility system software description

    International Nuclear Information System (INIS)

    Allen, J.; Chang, C.; Estep, P.; Huang, J.; Liu, J.; Marquez, M.; Mestad, S.; Pan, J.; Traversat, B.

    1991-12-01

    Large and costly detectors will be constructed during the next few years to study the interactions produced by the SSC. Efficient, cost-effective designs for these detectors will require careful thought and planning. Because it is not possible to test fully a proposed design in a scaled-down version, the adequacy of a proposed design will be determined by a detailed computer model of the detectors. Physics and detector simulations will be performed on the computer model using high-powered computing system at the Physics Detector Simulation Facility (PDSF). The SSCL has particular computing requirements for high-energy physics (HEP) Monte Carlo calculations for the simulation of SSCL physics and detectors. The numerical calculations to be performed in each simulation are lengthy and detailed; they could require many more months per run on a VAX 11/780 computer and may produce several gigabytes of data per run. Consequently, a distributed computing environment of several networked high-speed computing engines is envisioned to meet these needs. These networked computers will form the basis of a centralized facility for SSCL physics and detector simulation work. Our computer planning groups have determined that the most efficient, cost-effective way to provide these high-performance computing resources at this time is with RISC-based UNIX workstations. The modeling and simulation application software that will run on the computing system is usually written by physicists in FORTRAN language and may need thousands of hours of supercomputing time. The system software is the ''glue'' which integrates the distributed workstations and allows them to be managed as a single entity. This report will address the computing strategy for the SSC

  3. A system for automatic evaluation of simulation software

    Science.gov (United States)

    Ryan, J. P.; Hodges, B. C.

    1976-01-01

    Within the field of computer software, simulation and verification are complementary processes. Simulation methods can be used to verify software by performing variable range analysis. More general verification procedures, such as those described in this paper, can be implicitly, viewed as attempts at modeling the end-product software. From software requirement methodology, each component of the verification system has some element of simulation to it. Conversely, general verification procedures can be used to analyze simulation software. A dynamic analyzer is described which can be used to obtain properly scaled variables for an analog simulation, which is first digitally simulated. In a similar way, it is thought that the other system components and indeed the whole system itself have the potential of being effectively used in a simulation environment.

  4. Cosimulation of embedded system using RTOS software simulator

    Science.gov (United States)

    Wang, Shihao; Duan, Zhigang; Liu, Mingye

    2003-09-01

    Embedded system design often employs co-simulation to verify system's function; one efficient verification tool of software is Instruction Set Simulator (ISS). As a full functional model of target CPU, ISS interprets instruction of embedded software step by step, which usually is time-consuming since it simulates at low-level. Hence ISS often becomes the bottleneck of co-simulation in a complicated system. In this paper, a new software verification tools, the RTOS software simulator (RSS) was presented. The mechanism of its operation was described in a full details. In RSS method, RTOS API is extended and hardware simulator driver is adopted to deal with data-exchange and synchronism between the two simulators.

  5. Control system software, simulation, and robotic applications

    Science.gov (United States)

    Frisch, Harold P.

    1991-01-01

    All essential existing capabilities needed to create a man-machine interaction dynamics and performance (MMIDAP) capability are reviewed. The multibody system dynamics software program Order N DISCOS will be used for machine and musculo-skeletal dynamics modeling. The program JACK will be used for estimating and animating whole body human response to given loading situations and motion constraints. The basic elements of performance (BEP) task decomposition methodologies associated with the Human Performance Institute database will be used for performance assessment. Techniques for resolving the statically indeterminant muscular load sharing problem will be used for a detailed understanding of potential musculotendon or ligamentous fatigue, pain, discomfort, and trauma. The envisioned capacity is to be used for mechanical system design, human performance assessment, extrapolation of man/machine interaction test data, biomedical engineering, and soft prototyping within a concurrent engineering (CE) system.

  6. A Unique Software System For Simulation-to-Flight Research

    Science.gov (United States)

    Chung, Victoria I.; Hutchinson, Brian K.

    2001-01-01

    "Simulation-to-Flight" is a research development concept to reduce costs and increase testing efficiency of future major aeronautical research efforts at NASA. The simulation-to-flight concept is achieved by using common software and hardware, procedures, and processes for both piloted-simulation and flight testing. This concept was applied to the design and development of two full-size transport simulators, a research system installed on a NASA B-757 airplane, and two supporting laboratories. This paper describes the software system that supports the simulation-to-flight facilities. Examples of various simulation-to-flight experimental applications were also provided.

  7. Software simulation: a tool for enhancing control system design

    International Nuclear Information System (INIS)

    Sze, B.; Ridgway, G.H.

    2008-01-01

    The creation, implementation and management of engineering design tools are important to the quality and efficiency of any large engineering project. Some of the most complicated tools to develop are system simulators. The development and implementation of system simulators to support replacement fuel handling control systems is of particular interest to the Canadian nuclear industry given the current age of installations and the risk of obsolescence to many utilities. The use of such simulator tools has been known to significantly improve successful deployment of new software packages and maintenance-related software changes while reducing the time required for their overall development. Moreover, these simulation systems can also serve as operator training stations and provide a virtual environment for site engineers to test operational changes before they are uploaded to the actual system. (author)

  8. Simulation software support (S3) system a software testing and debugging tool

    International Nuclear Information System (INIS)

    Burgess, D.C.; Mahjouri, F.S.

    1990-01-01

    The largest percentage of technical effort in the software development process is accounted for debugging and testing. It is not unusual for a software development organization to spend over 50% of the total project effort on testing. In the extreme, testing of human-rated software (e.g., nuclear reactor monitoring, training simulator) can cost three to five times as much as all other software engineering steps combined. The Simulation Software Support (S 3 ) System, developed by the Link-Miles Simulation Corporation is ideally suited for real-time simulation applications which involve a large database with models programmed in FORTRAN. This paper will focus on testing elements of the S 3 system. In this paper system support software utilities are provided which enable the loading and execution of modules in the development environment. These elements include the Linking/Loader (LLD) for dynamically linking program modules and loading them into memory and the interactive executive (IEXEC) for controlling the execution of the modules. Features of the Interactive Symbolic Debugger (SD) and the Real Time Executive (RTEXEC) to support the unit and integrated testing will be explored

  9. A Software Defined Radio Based Airplane Communication Navigation Simulation System

    Science.gov (United States)

    He, L.; Zhong, H. T.; Song, D.

    2018-01-01

    Radio communication and navigation system plays important role in ensuring the safety of civil airplane in flight. Function and performance should be tested before these systems are installed on-board. Conventionally, a set of transmitter and receiver are needed for each system, thus all the equipment occupy a lot of space and are high cost. In this paper, software defined radio technology is applied to design a common hardware communication and navigation ground simulation system, which can host multiple airplane systems with different operating frequency, such as HF, VHF, VOR, ILS, ADF, etc. We use a broadband analog frontend hardware platform, universal software radio peripheral (USRP), to transmit/receive signal of different frequency band. Software is compiled by LabVIEW on computer, which interfaces with USRP through Ethernet, and is responsible for communication and navigation signal processing and system control. An integrated testing system is established to perform functional test and performance verification of the simulation signal, which demonstrate the feasibility of our design. The system is a low-cost and common hardware platform for multiple airplane systems, which provide helpful reference for integrated avionics design.

  10. Tool Support for Parametric Analysis of Large Software Simulation Systems

    Science.gov (United States)

    Schumann, Johann; Gundy-Burlet, Karen; Pasareanu, Corina; Menzies, Tim; Barrett, Tony

    2008-01-01

    The analysis of large and complex parameterized software systems, e.g., systems simulation in aerospace, is very complicated and time-consuming due to the large parameter space, and the complex, highly coupled nonlinear nature of the different system components. Thus, such systems are generally validated only in regions local to anticipated operating points rather than through characterization of the entire feasible operational envelope of the system. We have addressed the factors deterring such an analysis with a tool to support envelope assessment: we utilize a combination of advanced Monte Carlo generation with n-factor combinatorial parameter variations to limit the number of cases, but still explore important interactions in the parameter space in a systematic fashion. Additional test-cases, automatically generated from models (e.g., UML, Simulink, Stateflow) improve the coverage. The distributed test runs of the software system produce vast amounts of data, making manual analysis impossible. Our tool automatically analyzes the generated data through a combination of unsupervised Bayesian clustering techniques (AutoBayes) and supervised learning of critical parameter ranges using the treatment learner TAR3. The tool has been developed around the Trick simulation environment, which is widely used within NASA. We will present this tool with a GN&C (Guidance, Navigation and Control) simulation of a small satellite system.

  11. Development of an engine system simulation software package - ESIM

    Energy Technology Data Exchange (ETDEWEB)

    Erlandsson, Olof

    2000-10-01

    A software package, ESIM is developed for simulating internal combustion engine systems, including models for engine, manifolds, turbocharger, charge-air cooler (inter cooler) and inlet air heater. This study focus on the thermodynamic treatment and methods used in the models. It also includes some examples of system simulations made with these models for validation purposes. The engine model can be classified as a zero-dimensional, single zone model. It includes calculation of the valve flow process, models for heat release and models for in-cylinder, exhaust port and manifold heat transfer. Models are developed for handling turbocharger performance and charge air cooler characteristics. The main purpose of the project related to this work is to use the ESIM software to study heat balance and performance of homogeneous charge compression ignition (HCCI) engine systems. A short description of the HCCI engine is therefore included, pointing out the difficulties, or challenges regarding the HCCI engine, from a system perspective. However, the relations given here, and the code itself, is quite general, making it possible to use these models to simulate spark ignited, as well as direct injected engines.

  12. Physics Detector Simulation Facility Phase II system software description

    International Nuclear Information System (INIS)

    Scipioni, B.; Allen, J.; Chang, C.; Huang, J.; Liu, J.; Mestad, S.; Pan, J.; Marquez, M.; Estep, P.

    1993-05-01

    This paper presents the Physics Detector Simulation Facility (PDSF) Phase II system software. A key element in the design of a distributed computing environment for the PDSF has been the separation and distribution of the major functions. The facility has been designed to support batch and interactive processing, and to incorporate the file and tape storage systems. By distributing these functions, it is often possible to provide higher throughput and resource availability. Similarly, the design is intended to exploit event-level parallelism in an open distributed environment

  13. The simulation library of the Belle II software system

    Science.gov (United States)

    Kim, D. Y.; Ritter, M.; Bilka, T.; Bobrov, A.; Casarosa, G.; Chilikin, K.; Ferber, T.; Godang, R.; Jaegle, I.; Kandra, J.; Kodys, P.; Kuhr, T.; Kvasnicka, P.; Nakayama, H.; Piilonen, L.; Pulvermacher, C.; Santelj, L.; Schwenker, B.; Sibidanov, A.; Soloviev, Y.; Starič, M.; Uglov, T.

    2017-10-01

    SuperKEKB, the next generation B factory, has been constructed in Japan as an upgrade of KEKB. This brand new e+ e- collider is expected to deliver a very large data set for the Belle II experiment, which will be 50 times larger than the previous Belle sample. Both the triggered physics event rate and the background event rate will be increased by at least 10 times than the previous ones, and will create a challenging data taking environment for the Belle II detector. The software system of the Belle II experiment is designed to execute this ambitious plan. A full detector simulation library, which is a part of the Belle II software system, is created based on Geant4 and has been tested thoroughly. Recently the library has been upgraded with Geant4 version 10.1. The library is behaving as expected and it is utilized actively in producing Monte Carlo data sets for various studies. In this paper, we will explain the structure of the simulation library and the various interfaces to other packages including geometry and beam background simulation.

  14. Development of a dose simulation software for gamma irradiation systems

    International Nuclear Information System (INIS)

    Omi, Nelson Minoru

    2000-01-01

    The use of high temperature, thermal and chemical treatment are among the used sterilization process of food and many products. The ionizing radiation came as another option, it has being used for many purposes and it became available due to the technological development in the second half of the 20 th century. Together with sterilization, many uses of the ionizing radiation were developed, such as applications on health, industrial products and waste recycling, food irradiation, vulcanizing, polymerization and gems color enhancing. The 60 Co gamma stands out among the used radiation sources on commercial facilities. lt is used to optimize this process with many dose mapping tests. The objective of this work is to develop a software to simulate the doses in 60 Co gamma irradiation systems. lt can be used to optimize a process on the project stage of a facility and to make viability studies for new applications in installations already set up. The validation of this software was done comparing the simulation results with the dosimetry data of an operating irradiation plant. The flexibility of the software was verified with extra dosimetry tests performed in another sterilization facility. (author)

  15. Software Design for Interactive Graphic Radiation Treatment Simulation Systems*

    Science.gov (United States)

    Kalet, Ira J.; Sweeney, Christine; Jacky, Jonathan

    1990-01-01

    We examine issues in the design of interactive computer graphic simulation programs for radiation treatment planning (RTP), as well as expert system programs that automate parts of the RTP process, in light of ten years of experience at designing, building and using such programs. An experiment in object-oriented design using standard Pascal shows that while some advantage is gained from the design, it is still difficult to achieve modularity and to integrate expert system components. A new design based on the Common LISP Object System (CLOS) is described. This series of designs for RTP software shows that this application benefits in specific ways from object-oriented design methods and appropriate languages and tools.

  16. EON: software for long time simulations of atomic scale systems

    Science.gov (United States)

    Chill, Samuel T.; Welborn, Matthew; Terrell, Rye; Zhang, Liang; Berthet, Jean-Claude; Pedersen, Andreas; Jónsson, Hannes; Henkelman, Graeme

    2014-07-01

    The EON software is designed for simulations of the state-to-state evolution of atomic scale systems over timescales greatly exceeding that of direct classical dynamics. States are defined as collections of atomic configurations from which a minimization of the potential energy gives the same inherent structure. The time evolution is assumed to be governed by rare events, where transitions between states are uncorrelated and infrequent compared with the timescale of atomic vibrations. Several methods for calculating the state-to-state evolution have been implemented in EON, including parallel replica dynamics, hyperdynamics and adaptive kinetic Monte Carlo. Global optimization methods, including simulated annealing, basin hopping and minima hopping are also implemented. The software has a client/server architecture where the computationally intensive evaluations of the interatomic interactions are calculated on the client-side and the state-to-state evolution is managed by the server. The client supports optimization for different computer architectures to maximize computational efficiency. The server is written in Python so that developers have access to the high-level functionality without delving into the computationally intensive components. Communication between the server and clients is abstracted so that calculations can be deployed on a single machine, clusters using a queuing system, large parallel computers using a message passing interface, or within a distributed computing environment. A generic interface to the evaluation of the interatomic interactions is defined so that empirical potentials, such as in LAMMPS, and density functional theory as implemented in VASP and GPAW can be used interchangeably. Examples are given to demonstrate the range of systems that can be modeled, including surface diffusion and island ripening of adsorbed atoms on metal surfaces, molecular diffusion on the surface of ice and global structural optimization of nanoparticles.

  17. Analysis on flexible manufacturing system layout using arena simulation software

    Science.gov (United States)

    Fadzly, M. K.; Saad, Mohd Sazli; Shayfull, Z.

    2017-09-01

    Flexible manufacturing system (FMS) was defined as highly automated group technology machine cell, consisting of a group of processing stations interconnected by an automated material handling and storage system, and controlled by an integrated computer system. FMS can produce parts or products are in the mid-volume, mid-variety production range. The layout system in FMS is an important criterion to design the FMS system to produce a part or product. This facility layout of an FMS involves the positioning of cells within given boundaries, so as to minimize the total projected travel time between cells. Defining the layout includes specifying the spatial coordinates of each cell, its orientation in either a horizontal or vertical position, and the location of its load or unloads point. There are many types of FMS layout such as In-line, loop ladder and robot centered cell layout. The research is concentrating on the design and optimization FMS layout. The final conclusion can be summarized that the objective to design and optimisation of FMS layout for this study is successful because the FMS In-line layout is the best layout based on effective time and cost using ARENA simulation software.

  18. A software system for the simulation of chest lesions

    Science.gov (United States)

    Ryan, John T.; McEntee, Mark; Barrett, Saoirse; Evanoff, Michael; Manning, David; Brennan, Patrick

    2007-03-01

    We report on the development of a novel software tool for the simulation of chest lesions. This software tool was developed for use in our study to attain optimal ambient lighting conditions for chest radiology. This study involved 61 consultant radiologists from the American Board of Radiology. Because of its success, we intend to use the same tool for future studies. The software has two main functions: the simulation of lesions and retrieval of information for ROC (Receiver Operating Characteristic) and JAFROC (Jack-Knife Free Response ROC) analysis. The simulation layer operates by randomly selecting an image from a bank of reportedly normal chest x-rays. A random location is then generated for each lesion, which is checked against a reference lung-map. If the location is within the lung fields, as derived from the lung-map, a lesion is superimposed. Lesions are also randomly selected from a bank of manually created chest lesion images. A blending algorithm determines which are the best intensity levels for the lesion to sit naturally within the chest x-ray. The same software was used to run a study for all 61 radiologists. A sequence of images is displayed in random order. Half of these images had simulated lesions, ranging from subtle to obvious, and half of the images were normal. The operator then selects locations where he/she thinks lesions exist and grades the lesion accordingly. We have found that this software was very effective in this study and intend to use the same principles for future studies.

  19. Software and system development using virtual platforms full-system simulation with wind river simics

    CERN Document Server

    Aarno, Daniel

    2014-01-01

    Virtual platforms are finding widespread use in both pre- and post-silicon computer software and system development. They reduce time to market, improve system quality, make development more efficient, and enable truly concurrent hardware/software design and bring-up. Virtual platforms increase productivity with unparalleled inspection, configuration, and injection capabilities. In combination with other types of simulators, they provide full-system simulations where computer systems can be tested together with the environment in which they operate. This book is not only about what simulat

  20. Maintenance simulation: Software issues

    Energy Technology Data Exchange (ETDEWEB)

    Luk, C.H.; Jette, M.A.

    1995-07-01

    The maintenance of a distributed software system in a production environment involves: (1) maintaining software integrity, (2) maintaining and database integrity, (3) adding new features, and (4) adding new systems. These issues will be discussed in general: what they are and how they are handled. This paper will present our experience with a distributed resource management system that accounts for resources consumed, in real-time, on a network of heterogenous computers. The simulated environments to maintain this system will be presented relate to the four maintenance areas.

  1. PVSOFT99 - Photovoltaic (PV) System Sizing And Simulation Software

    African Journals Online (AJOL)

    A computer program (PVSOFT99) has been developed for sizing and simulation of stand-alone photovoltaic (PV) systems. Two distinct PV sizing algorithms, one based on the worst case and the other on the reliability concept, have been incorporated in the program. The reliability concept is generalized in that variation of ...

  2. Introduction to co-simulation of software and hardware in embedded processor systems

    Energy Technology Data Exchange (ETDEWEB)

    Dreike, P.L.; McCoy, J.A.

    1996-09-01

    From the dawn of the first use of microprocessors and microcontrollers in embedded systems, the software has been blamed for products being late to market, This is due to software being developed after hardware is fabricated. During the past few years, the use of Hardware Description (or Design) Languages (HDLs) and digital simulation have advanced to a point where the concurrent development of software and hardware can be contemplated using simulation environments. This offers the potential of 50% or greater reductions in time-to-market for embedded systems. This paper is a tutorial on the technical issues that underlie software-hardware (swhw) co-simulation, and the current state of the art. We review the traditional sequential hardware-software design paradigm, and suggest a paradigm for concurrent design, which is supported by co-simulation of software and hardware. This is followed by sections on HDLs modeling and simulation;hardware assisted approaches to simulation; microprocessor modeling methods; brief descriptions of four commercial products for sw-hw co-simulation and a description of our own experiments to develop a co-simulation environment.

  3. Developing Software Simulations

    Directory of Open Access Journals (Sweden)

    Tom Hall

    2007-06-01

    Full Text Available Programs in education and business often require learners to develop and demonstrate competence in specified areas and then be able to effectively apply this knowledge. One method to aid in developing a skill set in these areas is through the use of software simulations. These simulations can be used for learner demonstrations of competencies in a specified course as well as a review of the basic skills at the beginning of subsequent courses. The first section of this paper discusses ToolBook, the software used to develop our software simulations. The second section discusses the process of developing software simulations. The third part discusses how we have used software simulations to assess student knowledge of research design by providing simulations that allow the student to practice using SPSS and Excel.

  4. SIMULATION OF THE SYSTEMS WITH RENEWABLE ENERGY SOURCES USING HOMER SOFTWARE

    Directory of Open Access Journals (Sweden)

    FIRINCĂ S.D.

    2015-12-01

    Full Text Available This paper simulates by using the Homer software, distributed energy systems with capacity below 1 MW. Among the renewable energy sources are used wind and solar energy. For photovoltaic panels, we are considering two situations: fixed panels, oriented at 45 ° and panels with tracking system with two axis. Simulation results contain information regarding operation hours of the system throughout the year, energy produced from the renewable energy sources, energy consumption for the load, and excess of electrical energy. The Homer software also allows an economic analysis of these systems.

  5. Comparison of Engine Simulation Software for Development of Control System

    Directory of Open Access Journals (Sweden)

    KinYip Chan

    2013-01-01

    Full Text Available Most commonly used commercial engine simulation packages generate detailed estimation of the combustion and gas flow parameters. These parameters are required for advanced research on fluid flow and heat transfer and development of geometries of engine components. However, engine control involves different operating parameters. Various sensors are installed into the engine, the combustion performance is recorded, and data is sent to engine control unit (ECU. ECU computes the new set of parameters to make fine adjustments to actuators providing better engine performance. Such techniques include variable valve timing, variable ignition timing, variable air to fuel ratio, and variable compression ratio. In the present study, two of the commercial packages, Ricardo Wave and Lotus Engine Simulation, have been tested on the capabilities for engine control purposes. These packages are compared with an in-house developed package and with reference results available from the literature. Different numerical experiments have been carried out from which it can be concluded that all packages predict similar profiles of pressure and temperature in the engine cylinder. Moreover, those are in reasonable agreement with the reference results while in-house developed package is possible to run simulations with changing speed for engine control purpose.

  6. A software application for energy flow simulation of a grid connected photovoltaic system

    International Nuclear Information System (INIS)

    Hamad, Ayman A.; Alsaad, Mohammad A.

    2010-01-01

    A computer software application was developed to simulate hourly energy flow of a grid connected photovoltaic system. This software application enables conducting an operational evaluation of a studied photovoltaic system in terms of energy exchange with the electrical grid. The system model consists of a photovoltaic array, a converter and an optional generic energy storage component that supports scheduled charging/discharging. In addition to system design parameters, the software uses hourly solar data and hourly load data to determine the amount of energy exchanged with electrical grid for each hour of the simulated year. The resulting information is useful in assessing the impact of the system on demand for electrical energy of a building that uses it. The software also aggregates these hourly results in daily, monthly and full year sums. The software finds the financial benefit of the system as the difference in grid electrical energy cost between two simultaneously considered cases. One is with load supplied only by the electrical grid, while the other is with the photovoltaic system present and contributing energy. The software supports the energy pricing scheme used in Jordan for domestic consumers, which is based on slices of monthly consumption. By projecting the yearly financial results on the system lifetime, the application weighs the financial benefit resulting from using the system against its cost, thus facilitating an economical evaluation.

  7. Project Robot: A Software Simulation for Systems Engineering Education

    Science.gov (United States)

    Arnold, Ross D.; Wade, Jon P.

    2017-01-01

    The U.S. defense industry spends billions of dollars each year developing defense systems to keep the nation and allies secure. However, the failure rate of system development is notoriously high. Even when development efforts do succeed, they often do so with cost overruns and compromises in system performance. As a result, large amounts of money…

  8. Virtual Systems Pharmacology (ViSP software for mechanistic system-level model simulations

    Directory of Open Access Journals (Sweden)

    Sergey eErmakov

    2014-10-01

    Full Text Available Multiple software programs are available for designing and running large scale system-level pharmacology models used in the drug development process. Depending on the problem, scientists may be forced to use several modeling tools that could increase model development time, IT costs and so on. Therefore it is desirable to have a single platform that allows setting up and running large-scale simulations for the models that have been developed with different modeling tools. We developed a workflow and a software platform in which a model file is compiled into a self-contained executable that is no longer dependent on the software that was used to create the model. At the same time the full model specifics is preserved by presenting all model parameters as input parameters for the executable. This platform was implemented as a model agnostic, therapeutic area agnostic and web-based application with a database back-end that can be used to configure, manage and execute large-scale simulations for multiple models by multiple users. The user interface is designed to be easily configurable to reflect the specifics of the model and the user’s particular needs and the back-end database has been implemented to store and manage all aspects of the systems, such as Models, Virtual Patients, User Interface Settings, and Results. The platform can be adapted and deployed on an existing cluster or cloud computing environment. Its use was demonstrated with a metabolic disease systems pharmacology model that simulates the effects of two antidiabetic drugs, metformin and fasiglifam, in type 2 diabetes mellitus patients.

  9. Design and Simulation of Horn Antenna Using CST Software for GPR System

    Science.gov (United States)

    Joret, Ariffuddin; Sulong, M. S.; Abdullah, M. F. L.; Madun, Aziman; Haimi Dahlan, Samsul

    2018-04-01

    Detection of underground object can be made using a GPR system. This system is classified as a non-destructive technique (NDT) where the ground areas need not to be excavated. The technique used by the GPR system is by measuring the reflection of electromagnetic wave signal produced and detected by antenna which is known as the transmitter and the receiver antenna. In this study, a GPR system was studied by means of simulation using a Horn antenna as a transceiver antenna. The electromagnetic wave signal in this simulation is produced by current signal of an antenna which having a shape of modulation of Gaussian pulse which is having spectrum from 8 GHz until 12 GHz. CST and MATLAB Software are used in this GPR system simulation. A model of a Horn antenna has been designed using the CST software before the GPR’s system simulation modeled by adding a model of background in front of the Horn antenna. The simulation results show that the output signal of the Horn antenna can be used in detecting embedded object which are made from material of wood and iron. In addition, the simulation result has successfully developed a 3D model image of the GPR system using output signal of the Horn antenna. The embedded iron object in the GPR system simulation can be seen clearly by using this 3D image.

  10. Model reliability and software quality assurance in simulation of nuclear fuel waste management systems

    International Nuclear Information System (INIS)

    Oeren, T.I.; Elzas, M.S.; Sheng, G.; Wageningen Agricultural Univ., Netherlands; McMaster Univ., Hamilton, Ontario)

    1985-01-01

    As is the case with all scientific simulation studies, computerized simulation of nuclear fuel waste management systems can introduce and hide various types of errors. Frameworks to clarify issues of model reliability and software quality assurance are offered. Potential problems with reference to the main areas of concern for reliability and quality are discussed; e.g., experimental issues, decomposition, scope, fidelity, verification, requirements, testing, correctness, robustness are treated with reference to the experience gained in the past. A list comprising over 80 most common computerization errors is provided. Software tools and techniques used to detect and to correct computerization errors are discussed

  11. Object oriented software for simulation and reconstruction of big alignment systems

    International Nuclear Information System (INIS)

    Arce, P.

    2003-01-01

    Modern high-energy physics experiments require tracking detectors to provide high precision under difficult working conditions (high magnetic field, gravity loads and temperature gradients). This is the reason why several of them are deciding to implement optical alignment systems to monitor the displacement of tracking elements in operation. To simulate and reconstruct optical alignment systems a general purpose software, named COCOA, has been developed, using the object oriented paradigm and software engineering techniques. Thanks to the big flexibility in its design, COCOA is able to reconstruct any optical system made of a combination of the following objects: laser, x-hair laser, incoherent source--pinhole, lens, mirror, plate splitter, cube splitter, optical square, rhomboid prism, 2D sensor, 1D sensor, distance-meter, tilt-meter, user-defined. COCOA was designed to satisfy the requirements of the CMS alignment system, which has several thousands of components. Sparse matrix techniques had been investigated for solving non-linear least squares fits with such a big number of parameters. The soundness of COCOA has already been stressed in the reconstruction of the data of a full simulation of a quarter plane of the CMS muon alignment system, which implied solving a system of 900 equations with 850 unknown parameters. Full simulation of the whole CMS alignment system, with over 30,000 parameters, is quite advanced. The integration of COCOA in the CMS software framework is also under progress

  12. Simulations of oscillatory systems with award-winning software, physics of oscillations

    CERN Document Server

    Butikov, Eugene I

    2015-01-01

    Deepen Your Students' Understanding of Oscillations through Interactive Experiments Simulations of Oscillatory Systems: with Award-Winning Software, Physics of Oscillations provides a hands-on way of visualizing and understanding the fundamental concepts of the physics of oscillations. Both the textbook and software are designed as exploration-oriented supplements for courses in general physics and the theory of oscillations. The book is conveniently structured according to mathematical complexity. Each chapter in Part I contains activities, questions, exercises, and problems of varying levels of difficulty, from straightforward to quite challenging. Part II presents more sophisticated, highly mathematical material that delves into the serious theoretical background for the computer-aided study of oscillations. The software package allows students to observe the motion of linear and nonlinear mechanical oscillatory systems and to obtain plots of the variables that describe the systems along with phase diagram...

  13. Testing FSO WDM communication system in simulation software optiwave OptiSystem in different atmospheric environments

    Science.gov (United States)

    Vanderka, Ales; Hajek, Lukas; Bednarek, Lukas; Latal, Jan; Vitasek, Jan; Hejduk, Stanislav; Vasinek, Vladimir

    2016-09-01

    In this article the author's team deals with using Wavelength Division Multiplexing (WDM) for Free Space Optical (FSO) Communications. In FSO communication occurs due to the influence of atmospheric effect (attenuation, and fluctuation of the received power signal, influence turbulence) and the WDM channel suffers from interchannel crosstalk. There is considered only the one direction. The behavior FSO link was tested for one or eight channels. Here we will be dealing with modulation schemes OOK (On-Off keying), QAM (Quadrature Amplitude Modulation) and Subcarrier Intensity Modulation (SIM) based on a BPSK (Binary Phase Shift Keying). Simulation software OptiSystem 14 was used for tasting. For simulation some parameters were set according to real FSO link such as the datarate 1.25 Gbps, link range 1.4 km. Simulated FSO link used wavelength of 1550 nm with 0.8 nm spacing. There is obtained the influence of crosstalk and modulation format for the BER, depending on the amount of turbulence in the propagation medium.

  14. A Simulation Technique for Three-Dimensional Mechanical Systems Using Universal Software Systems of Analysis

    Directory of Open Access Journals (Sweden)

    V. A. Trudonoshin

    2015-01-01

    Full Text Available The article proposes a technique to develop mathematical models (MM of elements of the three-dimensional (3D mechanical systems for universal simulation software systems that allow us automatically generate the MM of a system based on MM elements and their connections. The technique is based on the MM of 3 D body. Linear and angular velocities are used as the main phase variables (unknown in the MM of the system, linear and angular movements are used as the additional ones, the latter being defined by the normalized quaternions that have computational advantages over turning angles.The paper has considered equations of dynamics, formulas of transition from the global coordinate system to the local one and vice versa. A spherical movable joint is presented as an example of the interaction element between the bodies. The paper shows the MM equivalent circuits of a body and a spherical joint. Such a representation, as the equivalent circuit, automatically enables us to obtain topological equations of the system. Various options to build equations of the joint and advices for their practical use are given.

  15. Utility application of simulation software

    International Nuclear Information System (INIS)

    Sudduth, A.L.

    1986-01-01

    The purpose of this paper is to discuss dynamic system simulation from the perspective of a successful utility user. In it, four aspects of the issue of utility use of simulation will be addressed: (1) What simulation software is available to utilities which can be of practical assistance with a modest investment in staff and training. (2) To what specific problems can utilities apply the technique of simulation and achieve reasonably cost effective results. (3) What the advantages are of in-house dynamic simulation capability, as opposed to depending on NSSS vendors or consultants. (4) What the prospects are for wider use of dynamic simulation in the utility industry

  16. NCS--a software for visual modeling and simulation of PWR nuclear power plant control system

    International Nuclear Information System (INIS)

    Cui Zhenhua

    1998-12-01

    The modeling and simulation of nuclear power plant control system has been investigated. Some mathematical models for rapid and accurate simulation are derived, including core models, pressurizer model, steam generator model, etc. Several numerical methods such as Runge-Kutta Method and Treanor Method are adopted to solve the above system models. In order to model the control system conveniently, a block diagram-oriented visual modeling platform is designed. And the Discrete Similarity Method is used to calculate the control system models. A corresponding simulating software, NCS, is developed for researching on the control systems of commercial nuclear power plant. And some satisfactory results are obtained. The research works will be of referential and applying value to design and analysis of nuclear power plant control system

  17. Software Geometry in Simulations

    Science.gov (United States)

    Alion, Tyler; Viren, Brett; Junk, Tom

    2015-04-01

    The Long Baseline Neutrino Experiment (LBNE) involves many detectors. The experiment's near detector (ND) facility, may ultimately involve several detectors. The far detector (FD) will be significantly larger than any other Liquid Argon (LAr) detector yet constructed; many prototype detectors are being constructed and studied to motivate a plethora of proposed FD designs. Whether it be a constructed prototype or a proposed ND/FD design, every design must be simulated and analyzed. This presents a considerable challenge to LBNE software experts; each detector geometry must be described to the simulation software in an efficient way which allows for multiple authors to easily collaborate. Furthermore, different geometry versions must be tracked throughout their use. We present a framework called General Geometry Description (GGD), written and developed by LBNE software collaborators for managing software to generate geometries. Though GGD is flexible enough to be used by any experiment working with detectors, we present it's first use in generating Geometry Description Markup Language (GDML) files to interface with LArSoft, a framework of detector simulations, event reconstruction, and data analyses written for all LAr technology users at Fermilab. Brett is the other of the framework discussed here, the General Geometry Description (GGD).

  18. PyMUS: Python-Based Simulation Software for Virtual Experiments on Motor Unit System

    Directory of Open Access Journals (Sweden)

    Hojeong Kim

    2018-04-01

    Full Text Available We constructed a physiologically plausible computationally efficient model of a motor unit and developed simulation software that allows for integrative investigations of the input–output processing in the motor unit system. The model motor unit was first built by coupling the motoneuron model and muscle unit model to a simplified axon model. To build the motoneuron model, we used a recently reported two-compartment modeling approach that accurately captures the key cell-type-related electrical properties under both passive conditions (somatic input resistance, membrane time constant, and signal attenuation properties between the soma and the dendrites and active conditions (rheobase current and afterhyperpolarization duration at the soma and plateau behavior at the dendrites. To construct the muscle unit, we used a recently developed muscle modeling approach that reflects the experimentally identified dependencies of muscle activation dynamics on isometric, isokinetic and dynamic variation in muscle length over a full range of stimulation frequencies. Then, we designed the simulation software based on the object-oriented programing paradigm and developed the software using open-source Python language to be fully operational using graphical user interfaces. Using the developed software, separate simulations could be performed for a single motoneuron, muscle unit and motor unit under a wide range of experimental input protocols, and a hierarchical analysis could be performed from a single channel to the entire system behavior. Our model motor unit and simulation software may represent efficient tools not only for researchers studying the neural control of force production from a cellular perspective but also for instructors and students in motor physiology classroom settings.

  19. PyMUS: Python-Based Simulation Software for Virtual Experiments on Motor Unit System.

    Science.gov (United States)

    Kim, Hojeong; Kim, Minjung

    2018-01-01

    We constructed a physiologically plausible computationally efficient model of a motor unit and developed simulation software that allows for integrative investigations of the input-output processing in the motor unit system. The model motor unit was first built by coupling the motoneuron model and muscle unit model to a simplified axon model. To build the motoneuron model, we used a recently reported two-compartment modeling approach that accurately captures the key cell-type-related electrical properties under both passive conditions (somatic input resistance, membrane time constant, and signal attenuation properties between the soma and the dendrites) and active conditions (rheobase current and afterhyperpolarization duration at the soma and plateau behavior at the dendrites). To construct the muscle unit, we used a recently developed muscle modeling approach that reflects the experimentally identified dependencies of muscle activation dynamics on isometric, isokinetic and dynamic variation in muscle length over a full range of stimulation frequencies. Then, we designed the simulation software based on the object-oriented programing paradigm and developed the software using open-source Python language to be fully operational using graphical user interfaces. Using the developed software, separate simulations could be performed for a single motoneuron, muscle unit and motor unit under a wide range of experimental input protocols, and a hierarchical analysis could be performed from a single channel to the entire system behavior. Our model motor unit and simulation software may represent efficient tools not only for researchers studying the neural control of force production from a cellular perspective but also for instructors and students in motor physiology classroom settings.

  20. Object oriented software for simulation and reconstruction of big alignment systems

    CERN Document Server

    Arce, P

    2003-01-01

    Modern high-energy physics experiments require tracking detectors to provide high precision under difficult working conditions (high magnetic field, gravity loads and temperature gradients). This is the reason why several of them are deciding to implement optical alignment systems to monitor the displacement of tracking elements in operation. To simulate and reconstruct optical alignment systems a general purpose software, named COCOA, has been developed, using the object oriented paradigm and software engineering techniques. Thanks to the big flexibility in its design, COCOA is able to reconstruct any optical system made of a combination of the following objects: laser, x-hair laser, incoherent source - pinhole, lens, mirror, plate splitter, cube splitter, optical square, rhomboid prism, 2D sensor, 1D sensor, distance-meter, tilt-meter, user-defined. COCOA was designed to satisfy the requirements of the CMS alignment system, which has several thousands of components. Sparse matrix techniques had been investi...

  1. A Reconfigurable Simulation-Based Test System for Automatically Assessing Software Operating Skills

    Science.gov (United States)

    Su, Jun-Ming; Lin, Huan-Yu

    2015-01-01

    In recent years, software operating skills, the ability in computer literacy to solve problems using specific software, has become much more important. A great deal of research has also proven that students' software operating skills can be efficiently improved by practicing customized virtual and simulated examinations. However, constructing…

  2. Improvement of Simulation Method in Validation of Software of the Coordinate Measuring Systems

    Science.gov (United States)

    Nieciąg, Halina

    2015-10-01

    Software is used in order to accomplish various tasks at each stage of the functioning of modern measuring systems. Before metrological confirmation of measuring equipment, the system has to be validated. This paper discusses the method for conducting validation studies of a fragment of software to calculate the values of measurands. Due to the number and nature of the variables affecting the coordinate measurement results and the complex character and multi-dimensionality of measurands, the study used the Monte Carlo method of numerical simulation. The article presents an attempt of possible improvement of results obtained by classic Monte Carlo tools. The algorithm LHS (Latin Hypercube Sampling) was implemented as alternative to the simple sampling schema of classic algorithm.

  3. Improvement of Simulation Method in Validation of Software of the Coordinate Measuring Systems

    Directory of Open Access Journals (Sweden)

    Nieciąg Halina

    2015-10-01

    Full Text Available Software is used in order to accomplish various tasks at each stage of the functioning of modern measuring systems. Before metrological confirmation of measuring equipment, the system has to be validated. This paper discusses the method for conducting validation studies of a fragment of software to calculate the values of measurands. Due to the number and nature of the variables affecting the coordinate measurement results and the complex character and multi-dimensionality of measurands, the study used the Monte Carlo method of numerical simulation. The article presents an attempt of possible improvement of results obtained by classic Monte Carlo tools. The algorithm LHS (Latin Hypercube Sampling was implemented as alternative to the simple sampling schema of classic algorithm.

  4. Physics Simulation Software for Autonomous Propellant Loading and Gas House Autonomous System Monitoring

    Science.gov (United States)

    Regalado Reyes, Bjorn Constant

    2015-01-01

    1. Kennedy Space Center (KSC) is developing a mobile launching system with autonomous propellant loading capabilities for liquid-fueled rockets. An autonomous system will be responsible for monitoring and controlling the storage, loading and transferring of cryogenic propellants. The Physics Simulation Software will reproduce the sensor data seen during the delivery of cryogenic fluids including valve positions, pressures, temperatures and flow rates. The simulator will provide insight into the functionality of the propellant systems and demonstrate the effects of potential faults. This will provide verification of the communications protocols and the autonomous system control. 2. The High Pressure Gas Facility (HPGF) stores and distributes hydrogen, nitrogen, helium and high pressure air. The hydrogen and nitrogen are stored in cryogenic liquid state. The cryogenic fluids pose several hazards to operators and the storage and transfer equipment. Constant monitoring of pressures, temperatures and flow rates are required in order to maintain the safety of personnel and equipment during the handling and storage of these commodities. The Gas House Autonomous System Monitoring software will be responsible for constantly observing and recording sensor data, identifying and predicting faults and relaying hazard and operational information to the operators.

  5. Creating and Testing Simulation Software

    Science.gov (United States)

    Heinich, Christina M.

    2013-01-01

    The goal of this project is to learn about the software development process, specifically the process to test and fix components of the software. The paper will cover the techniques of testing code, and the benefits of using one style of testing over another. It will also discuss the overall software design and development lifecycle, and how code testing plays an integral role in it. Coding is notorious for always needing to be debugged due to coding errors or faulty program design. Writing tests either before or during program creation that cover all aspects of the code provide a relatively easy way to locate and fix errors, which will in turn decrease the necessity to fix a program after it is released for common use. The backdrop for this paper is the Spaceport Command and Control System (SCCS) Simulation Computer Software Configuration Item (CSCI), a project whose goal is to simulate a launch using simulated models of the ground systems and the connections between them and the control room. The simulations will be used for training and to ensure that all possible outcomes and complications are prepared for before the actual launch day. The code being tested is the Programmable Logic Controller Interface (PLCIF) code, the component responsible for transferring the information from the models to the model Programmable Logic Controllers (PLCs), basic computers that are used for very simple tasks.

  6. Simulator for testing hardware and software of the office system with RFID tags

    Directory of Open Access Journals (Sweden)

    Nowicki Tadeusz

    2017-01-01

    Full Text Available This paper presents the method for examining the properties of the RFID-tagged document management system. The system is composed of computers, where the software for supporting processes of the RFID-tagged documents was installed. Furthermore, the system cooperates with many other elements of the office (cabinets, sluices, copiers, try rider, end so one. The examination of the properties of the RFID-tagged document management system is, in this case, complex due to the number of a possible examination scenarios. The simulator method for examining the system properties was design and implemented. It allows to conduct the examination of the properties in a short period of time for numerous testing scenarios.

  7. Software simulator for property investigation of document management system with RFID tags

    Directory of Open Access Journals (Sweden)

    Kiedrowicz Maciej

    2016-01-01

    Full Text Available The study outlines the method for examining the properties of the RFID-tagged document management system. The system is composed of computers, where the software for supporting processes of the RFID-tagged doc-uments was installed. Furthermore, the system cooperates with many other elements of the secret office (cabinets, sluices, photocopiers, desks. The examination of the properties of the RFID-tagged document management system is, in this case, complex due to the number of a possible examination scenarios. The simulation method for examining the system properties was proposed. It allows to conduct the examination of the properties in a short period of time for numerous testing scenarios.

  8. A large scale software system for simulation and design optimization of mechanical systems

    Science.gov (United States)

    Dopker, Bernhard; Haug, Edward J.

    1989-01-01

    The concept of an advanced integrated, networked simulation and design system is outlined. Such an advanced system can be developed utilizing existing codes without compromising the integrity and functionality of the system. An example has been used to demonstrate the applicability of the concept of the integrated system outlined here. The development of an integrated system can be done incrementally. Initial capabilities can be developed and implemented without having a detailed design of the global system. Only a conceptual global system must exist. For a fully integrated, user friendly design system, further research is needed in the areas of engineering data bases, distributed data bases, and advanced user interface design.

  9. Software-Engineering Process Simulation (SEPS) model

    Science.gov (United States)

    Lin, C. Y.; Abdel-Hamid, T.; Sherif, J. S.

    1992-01-01

    The Software Engineering Process Simulation (SEPS) model is described which was developed at JPL. SEPS is a dynamic simulation model of the software project development process. It uses the feedback principles of system dynamics to simulate the dynamic interactions among various software life cycle development activities and management decision making processes. The model is designed to be a planning tool to examine tradeoffs of cost, schedule, and functionality, and to test the implications of different managerial policies on a project's outcome. Furthermore, SEPS will enable software managers to gain a better understanding of the dynamics of software project development and perform postmodern assessments.

  10. Software system safety

    Science.gov (United States)

    Uber, James G.

    1988-01-01

    Software itself is not hazardous, but since software and hardware share common interfaces there is an opportunity for software to create hazards. Further, these software systems are complex, and proven methods for the design, analysis, and measurement of software safety are not yet available. Some past software failures, future NASA software trends, software engineering methods, and tools and techniques for various software safety analyses are reviewed. Recommendations to NASA are made based on this review.

  11. Modelling and Simulating Complex Systems in Biology: introducing NetBioDyn : A Pedagogical and Intuitive Agent-Based Software

    OpenAIRE

    Ballet, Pascal; Rivière, Jérémy; Pothet, Alain; Théron, Michaël; Pichavant, Karine; Abautret, Frank; Fronville, Alexandra; Rodin, Vincent

    2017-01-01

    International audience; Modelling and teaching complex biological systems is a difficult process. Multi-Agent Based Simulations (MABS) have proved to be an appropriate approach both in research and education when dealing with such systems including emergent, self-organizing phenomena. This chapter presents NetBioDyn, an original software aimed at biologists (students, teachers, researchers) to easily build and simulate complex biological mechanisms observed in multicellular and molecular syst...

  12. SOFTWARE FOR SIMULATION OF TECHNOLOGICAL ADAPTATION OF THE OPTICAL INSTRUMENTS SYSTEMS

    Directory of Open Access Journals (Sweden)

    N. K. Artioukhina

    2012-01-01

    Full Text Available Programs for calculation and analysis of optical systems of any class are provides. The most effective was to combine the programs into a complex with the general system of mathematical models. A characteristic feature is to unify the exchange of information between these programs and software systems Opal and Zemax.

  13. Software as a service approach to sensor simulation software deployment

    Science.gov (United States)

    Webster, Steven; Miller, Gordon; Mayott, Gregory

    2012-05-01

    Traditionally, military simulation has been problem domain specific. Executing an exercise currently requires multiple simulation software providers to specialize, deploy, and configure their respective implementations, integrate the collection of software to achieve a specific system behavior, and then execute for the purpose at hand. This approach leads to rigid system integrations which require simulation expertise for each deployment due to changes in location, hardware, and software. Our alternative is Software as a Service (SaaS) predicated on the virtualization of Night Vision Electronic Sensors (NVESD) sensor simulations as an exemplary case. Management middleware elements layer self provisioning, configuration, and integration services onto the virtualized sensors to present a system of services at run time. Given an Infrastructure as a Service (IaaS) environment, enabled and managed system of simulations yields a durable SaaS delivery without requiring user simulation expertise. Persistent SaaS simulations would provide on demand availability to connected users, decrease integration costs and timelines, and benefit the domain community from immediate deployment of lessons learned.

  14. A bobsleigh simulator software

    Energy Technology Data Exchange (ETDEWEB)

    Rempfler, Georg S., E-mail: georg.rempfler@alumni.ethz.ch [ETH Zurich, CLA G23.3, IMES—Center of Mechanics (Switzerland); Glocker, Christoph, E-mail: glocker@imes.mavt.ethz.ch [ETH Zurich, CLA J23.1, IMES—Center of Mechanics (Switzerland)

    2016-03-15

    This paper presents a model of the artificial ice track in Whistler, Canada that is based on its construction data, and a model of a two-men bobsleigh consisting of nine rigid bodies, having 13 degrees of freedom and incorporating 17 hard frictional contacts. These models are implemented within a simulator that is capable of performing accurate real time simulations of piloted runs on commonly available PC hardware. The simulation is verified against the results of the official two-men race that took place during the Olympic Winter Games in 2010. The simulator has been used by several professional Swiss pilots during their preparation for the 2014 Olympic Winter Games in Sochi, Russia. The simulator is exploited to analyse and judge the range of possible driving lines regarding speed and runtime improvements. It could also serve to consult track designers about safety issues and sleigh constructors about the expected dynamics on a track.

  15. A bobsleigh simulator software

    International Nuclear Information System (INIS)

    Rempfler, Georg S.; Glocker, Christoph

    2016-01-01

    This paper presents a model of the artificial ice track in Whistler, Canada that is based on its construction data, and a model of a two-men bobsleigh consisting of nine rigid bodies, having 13 degrees of freedom and incorporating 17 hard frictional contacts. These models are implemented within a simulator that is capable of performing accurate real time simulations of piloted runs on commonly available PC hardware. The simulation is verified against the results of the official two-men race that took place during the Olympic Winter Games in 2010. The simulator has been used by several professional Swiss pilots during their preparation for the 2014 Olympic Winter Games in Sochi, Russia. The simulator is exploited to analyse and judge the range of possible driving lines regarding speed and runtime improvements. It could also serve to consult track designers about safety issues and sleigh constructors about the expected dynamics on a track.

  16. A Simulation Software for the Analysis of Cropping Systems in Livestock Farms

    Directory of Open Access Journals (Sweden)

    Tommaso Maggiore

    2011-02-01

    Full Text Available Simulation models can support quantitative and integrated analyses of agricultural systems. In this paper we describe VA.TE., a computer program developed to support the preparation and evaluation of nitrogen fertilising plans for livestock farms in the Lombardy region (northern Italy. The program integrates the cropping systems simulation model CropSyst with several regional agricultural databases, and provides the users with a simple framework for applying the model and interpreting results. VA.TE. makes good use of available data, integrating into a single relational database existing information about soils, climate, farms, animal breeds, crops and crop managements, and providing estimates of missing input variables. A simulation engine manages the entire simulation process: choice of farms to be simulated, model parameterisation, creation of model inputs, simulation of scenarios and analysis of model outputs. The program permits to apply at farm scale a model originally designed for the lower scale of homogeneous land parcel. It manages alternative simulation scenarios for each farm, helping to identify solutions to combine low nitrate losses and satisfactory crop yields. Example simulation results for three farms located on different soils and having varying levels of nitrogen surplus show that the integrated system (model + database can manage various simulations automatically, and that strategies to improve N management can be refined by analysing the simulated amounts and temporal patterns of nitrogen leaching.We conclude by discussing the issues regarding the integration of existing regional databases with simulation models.

  17. A Simulation Software for the Analysis of Cropping Systems in Livestock Farms

    Directory of Open Access Journals (Sweden)

    Luca Bechini

    2008-09-01

    Full Text Available Simulation models can support quantitative and integrated analyses of agricultural systems. In this paper we describe VA.TE., a computer program developed to support the preparation and evaluation of nitrogen fertilising plans for livestock farms in the Lombardy region (northern Italy. The program integrates the cropping systems simulation model CropSyst with several regional agricultural databases, and provides the users with a simple framework for applying the model and interpreting results. VA.TE. makes good use of available data, integrating into a single relational database existing information about soils, climate, farms, animal breeds, crops and crop managements, and providing estimates of missing input variables. A simulation engine manages the entire simulation process: choice of farms to be simulated, model parameterisation, creation of model inputs, simulation of scenarios and analysis of model outputs. The program permits to apply at farm scale a model originally designed for the lower scale of homogeneous land parcel. It manages alternative simulation scenarios for each farm, helping to identify solutions to combine low nitrate losses and satisfactory crop yields. Example simulation results for three farms located on different soils and having varying levels of nitrogen surplus show that the integrated system (model + database can manage various simulations automatically, and that strategies to improve N management can be refined by analysing the simulated amounts and temporal patterns of nitrogen leaching.We conclude by discussing the issues regarding the integration of existing regional databases with simulation models.

  18. StochKit2: software for discrete stochastic simulation of biochemical systems with events.

    Science.gov (United States)

    Sanft, Kevin R; Wu, Sheng; Roh, Min; Fu, Jin; Lim, Rone Kwei; Petzold, Linda R

    2011-09-01

    StochKit2 is the first major upgrade of the popular StochKit stochastic simulation software package. StochKit2 provides highly efficient implementations of several variants of Gillespie's stochastic simulation algorithm (SSA), and tau-leaping with automatic step size selection. StochKit2 features include automatic selection of the optimal SSA method based on model properties, event handling, and automatic parallelism on multicore architectures. The underlying structure of the code has been completely updated to provide a flexible framework for extending its functionality. StochKit2 runs on Linux/Unix, Mac OS X and Windows. It is freely available under GPL version 3 and can be downloaded from http://sourceforge.net/projects/stochkit/. petzold@engineering.ucsb.edu.

  19. Evolvable Neural Software System

    Science.gov (United States)

    Curtis, Steven A.

    2009-01-01

    The Evolvable Neural Software System (ENSS) is composed of sets of Neural Basis Functions (NBFs), which can be totally autonomously created and removed according to the changing needs and requirements of the software system. The resulting structure is both hierarchical and self-similar in that a given set of NBFs may have a ruler NBF, which in turn communicates with other sets of NBFs. These sets of NBFs may function as nodes to a ruler node, which are also NBF constructs. In this manner, the synthetic neural system can exhibit the complexity, three-dimensional connectivity, and adaptability of biological neural systems. An added advantage of ENSS over a natural neural system is its ability to modify its core genetic code in response to environmental changes as reflected in needs and requirements. The neural system is fully adaptive and evolvable and is trainable before release. It continues to rewire itself while on the job. The NBF is a unique, bilevel intelligence neural system composed of a higher-level heuristic neural system (HNS) and a lower-level, autonomic neural system (ANS). Taken together, the HNS and the ANS give each NBF the complete capabilities of a biological neural system to match sensory inputs to actions. Another feature of the NBF is the Evolvable Neural Interface (ENI), which links the HNS and ANS. The ENI solves the interface problem between these two systems by actively adapting and evolving from a primitive initial state (a Neural Thread) to a complicated, operational ENI and successfully adapting to a training sequence of sensory input. This simulates the adaptation of a biological neural system in a developmental phase. Within the greater multi-NBF and multi-node ENSS, self-similar ENI s provide the basis for inter-NBF and inter-node connectivity.

  20. Software Intensive Systems

    National Research Council Canada - National Science Library

    Horvitz, E; Katz, D. J; Rumpf, R. L; Shrobe, H; Smith, T. B; Webber, G. E; Williamson, W. E; Winston, P. H; Wolbarsht, James L

    2006-01-01

    .... Additionally, recommend that DoN invest in software engineering, particularly as it complements commercial industry developments and promotes the application of systems engineering methodology...

  1. Hardware-software system for simulating and analyzing earthquakes applied to civil structures

    Directory of Open Access Journals (Sweden)

    J. P. Amezquita-Sanchez

    2012-01-01

    Full Text Available The occurrence of recent strong earthquakes, the incessant worldwide movements of tectonic plates and the continuous ambient vibrations caused by traffic and wind have increased the interest of researchers in improving the capacity of energy dissipation to avoid damages to civil structures. Experimental testing of structural systems is essential for the understanding of physical behaviors and the building of appropriate analytic models in order to expose difficulties that may not have been considered in analytical studies. This paper presents a hardware-software system for exciting, monitoring and analyzing simultaneously a structure under earthquake signals and other types of signals in real-time. Effectiveness of the proposed system has been validated by experimental case studies and has been found to be a useful tool in the analysis of earthquake effects on structures.

  2. Simulation-based Testing of Control Software

    Energy Technology Data Exchange (ETDEWEB)

    Ozmen, Ozgur [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nutaro, James J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sanyal, Jibonananda [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Olama, Mohammed M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-02-10

    It is impossible to adequately test complex software by examining its operation in a physical prototype of the system monitored. Adequate test coverage can require millions of test cases, and the cost of equipment prototypes combined with the real-time constraints of testing with them makes it infeasible to sample more than a small number of these tests. Model based testing seeks to avoid this problem by allowing for large numbers of relatively inexpensive virtual prototypes that operate in simulation time at a speed limited only by the available computing resources. In this report, we describe how a computer system emulator can be used as part of a model based testing environment; specifically, we show that a complete software stack including operating system and application software - can be deployed within a simulated environment, and that these simulations can proceed as fast as possible. To illustrate this approach to model based testing, we describe how it is being used to test several building control systems that act to coordinate air conditioning loads for the purpose of reducing peak demand. These tests involve the use of ADEVS (A Discrete Event System Simulator) and QEMU (Quick Emulator) to host the operational software within the simulation, and a building model developed with the MODELICA programming language using Buildings Library and packaged as an FMU (Functional Mock-up Unit) that serves as the virtual test environment.

  3. Software for simulation of nuclear simulation of nuclear installations

    International Nuclear Information System (INIS)

    Castaneda, J.O.; Ramos, L.M.; Arjona, O.; Rodriguez, L.

    1993-01-01

    The software is an instrument to build conceptual-type simulators of low, medium and full scale for used in nuclear installations. The system is composed by composed by two basic modules: one for the edition and the other for the simulation. The first one allows to prepare the information to simulate: mathematical model, technological design (fundamentally, operation board or mnemotechnical design), parameters to be shown, failures to be simulated

  4. Software for simulating IMRT protocol

    Energy Technology Data Exchange (ETDEWEB)

    Fonseca, Thelma C.F.; Campos, Tarcisio P.R. de, E-mail: tcff@ufmg.b, E-mail: campos@nuclear.ufmg.b [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Dept. de Engenharia Nuclear

    2009-07-01

    The Intensity Modulated Radiation Therapy - IMRT is an advanced technique to cancer treatment widely used on oncology around the world. The present paper describes the SOFT-RT software which is a tool for simulating IMRT protocol. Also, it will be present a cerebral tumor case of studied in which three irradiation windows with distinct orientation were applied. The SOFT-RT collect and export data to MCNP code. This code simulates the photon transport on the voxel model. Later, a out-module from SOFT-RT import the results and express the dose-response superimposing dose and voxel model in a tree-dimensional graphic representation. The present paper address the IMRT software and its function as well a cerebral tumor case of studied is showed. The graphic interface of the SOFT-RT illustrates the example case. (author)

  5. Software for simulating IMRT protocol

    International Nuclear Information System (INIS)

    Fonseca, Thelma C.F.; Campos, Tarcisio P.R. de

    2009-01-01

    The Intensity Modulated Radiation Therapy - IMRT is an advanced technique to cancer treatment widely used on oncology around the world. The present paper describes the SOFT-RT software which is a tool for simulating IMRT protocol. Also, it will be present a cerebral tumor case of studied in which three irradiation windows with distinct orientation were applied. The SOFT-RT collect and export data to MCNP code. This code simulates the photon transport on the voxel model. Later, a out-module from SOFT-RT import the results and express the dose-response superimposing dose and voxel model in a tree-dimensional graphic representation. The present paper address the IMRT software and its function as well a cerebral tumor case of studied is showed. The graphic interface of the SOFT-RT illustrates the example case. (author)

  6. Composing simulations using persistent software components

    Energy Technology Data Exchange (ETDEWEB)

    Holland, J.V.; Michelsen, R.E.; Powell, D.R.; Upton, S.C.; Thompson, D.R.

    1999-03-01

    The traditional process for developing large-scale simulations is cumbersome, time consuming, costly, and in some cases, inadequate. The topics of software components and component-based software engineering are being explored by software professionals in academic and industrial settings. A component is a well-delineated, relatively independent, and replaceable part of a software system that performs a specific function. Many researchers have addressed the potential to derive a component-based approach to simulations in general, and a few have focused on military simulations in particular. In a component-based approach, functional or logical blocks of the simulation entities are represented as coherent collections of components satisfying explicitly defined interface requirements. A simulation is a top-level aggregate comprised of a collection of components that interact with each other in the context of a simulated environment. A component may represent a simulation artifact, an agent, or any entity that can generated events affecting itself, other simulated entities, or the state of the system. The component-based approach promotes code reuse, contributes to reducing time spent validating or verifying models, and promises to reduce the cost of development while still delivering tailored simulations specific to analysis questions. The Integrated Virtual Environment for Simulation (IVES) is a composition-centered framework to achieve this potential. IVES is a Java implementation of simulation composition concepts developed at Los Alamos National Laboratory for use in several application domains. In this paper, its use in the military domain is demonstrated via the simulation of dismounted infantry in an urban environment.

  7. Generalized Fluid System Simulation Program (GFSSP) Version 6 - General Purpose Thermo-Fluid Network Analysis Software

    Science.gov (United States)

    Majumdar, Alok; Leclair, Andre; Moore, Ric; Schallhorn, Paul

    2011-01-01

    GFSSP stands for Generalized Fluid System Simulation Program. It is a general-purpose computer program to compute pressure, temperature and flow distribution in a flow network. GFSSP calculates pressure, temperature, and concentrations at nodes and calculates flow rates through branches. It was primarily developed to analyze Internal Flow Analysis of a Turbopump Transient Flow Analysis of a Propulsion System. GFSSP development started in 1994 with an objective to provide a generalized and easy to use flow analysis tool for thermo-fluid systems.

  8. Coupling an analytical description of anti-scatter grids with simulation software of radiographic systems using Monte Carlo code

    International Nuclear Information System (INIS)

    Rinkel, J.; Dinten, J.M.; Tabary, J.

    2004-01-01

    The use of focused anti-scatter grids on digital radiographic systems with two-dimensional detectors produces acquisitions with a decreased scatter to primary ratio and thus improved contrast and resolution. Simulation software is of great interest in optimizing grid configuration according to a specific application. Classical simulators are based on complete detailed geometric descriptions of the grid. They are accurate but very time consuming since they use Monte Carlo code to simulate scatter within the high-frequency grids. We propose a new practical method which couples an analytical simulation of the grid interaction with a radiographic system simulation program. First, a two dimensional matrix of probability depending on the grid is created offline, in which the first dimension represents the angle of impact with respect to the normal to the grid lines and the other the energy of the photon. This matrix of probability is then used by the Monte Carlo simulation software in order to provide the final scattered flux image. To evaluate the gain of CPU time, we define the increasing factor as the increase of CPU time of the simulation with as opposed to without the grid. Increasing factors were calculated with the new model and with classical methods representing the grid with its CAD model as part of the object. With the new method, increasing factors are shorter by one to two orders of magnitude compared with the second one. These results were obtained with a difference in calculated scatter of less than five percent between the new and the classical method. (authors)

  9. Use of MBS (ADAMS / CAR software in simulations of vehicle suspension systems

    Directory of Open Access Journals (Sweden)

    Łukasz KONIECZNY

    2014-03-01

    Full Text Available The results of the examination of a vehicle suspension system in the plate position are presented in the paper. The model vehicle is a Fiat Seicento with front independent suspension, McPherson type, with the steering system and with the semi-trailing arm in the rear suspension. Identification of the model was made by comparing the simulation results with the results from the test stand. A multibody model of the vehicle will be used in studies of the impact of shock absorber technical conditions on the dynamics of automotive vehicles.

  10. Implementation of Software Tools for Hybrid Control Rooms in the Human Systems Simulation Laboratory

    International Nuclear Information System (INIS)

    Jokstad, Håkon; Berntsson, Olof; McDonald, Robert; Boring, Ronald; Hallbert, Bruce; Fitzgerald, Kirk

    2014-01-01

    The Institute for Energy Technology (IFE) and Idaho National Laboratory have designed, implemented, tested and installed a functioning prototype of a set of large screen overview and procedure support displays for the Generic Pressurized Water Reactor (GPWR) simulator in the U.S. Department of Energy's Human Systems Simulation Laboratory. The overview display is based on IFE's extensive experiences with large screen overview displays in the Halden Man-Machine Laboratory (HAMMLAB), and presents the main control room indicators on a combined three-screen display. The procedure support displays are designed and implemented to provide a compact but still comprehensive overview of the relevant process measurements and indicators to support operators' good situational awareness during the performance of various types of procedures and plant conditions.

  11. Implementation of Software Tools for Hybrid Control Rooms in the Human Systems Simulation Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Jokstad, Håkon [Halden Reactor Project, Halden (Norway); Berntsson, Olof [Halden Reactor Project, Halden (Norway); McDonald, Robert [Halden Reactor Project, Halden (Norway); Boring, Ronald [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hallbert, Bruce [Idaho National Lab. (INL), Idaho Falls, ID (United States); Fitzgerald, Kirk [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-11-01

    The Institute for Energy Technology (IFE) and Idaho National Laboratory have designed, implemented, tested and installed a functioning prototype of a set of large screen overview and procedure support displays for the Generic Pressurized Water Reactor (GPWR) simulator in the U.S. Department of Energy’s Human Systems Simulation Laboratory. The overview display is based on IFE’s extensive experiences with large screen overview displays in the Halden Man-Machine Laboratory (HAMMLAB), and presents the main control room indicators on a combined three-screen display. The procedure support displays are designed and implemented to provide a compact but still comprehensive overview of the relevant process measurements and indicators to support operators' good situational awareness during the performance of various types of procedures and plant conditions.

  12. Software Simulation of Hot Tearing

    DEFF Research Database (Denmark)

    Andersen, S.; Hansen, P.N.; Hattel, Jesper Henri

    1999-01-01

    The brittleness of a solidifying alloy in a temperature range near the solidus temperature has been recognised since the fifties as the mechanism responsible for hot tearing. Due to this brittlenes, the metal will crack under even small amounts of strain in that temperature range. We see these hot...... tears in castings close to hot centres, where the level of strain is often too high.Although the hot tearing mechanism is well understood, until now it has been difficult to do much to reduce the hot tearing tendency in a casting. In the seventies, good hot tearing criteria were developed by considering...... the solidification rate and the strain rate of the hot tear prone areas. But, until recently it was only possible to simulate the solidification rate, so that the criteria could not be used effectively.Today, with new software developments, it is possible to also simulate the strain rate in the hot tear prone areas...

  13. Security System Software

    Science.gov (United States)

    1993-01-01

    C Language Integration Production System (CLIPS), a NASA-developed expert systems program, has enabled a security systems manufacturer to design a new generation of hardware. C.CURESystem 1 Plus, manufactured by Software House, is a software based system that is used with a variety of access control hardware at installations around the world. Users can manage large amounts of information, solve unique security problems and control entry and time scheduling. CLIPS acts as an information management tool when accessed by C.CURESystem 1 Plus. It asks questions about the hardware and when given the answer, recommends possible quick solutions by non-expert persons.

  14. Software verification, model validation, and hydrogeologic modelling aspects in nuclear waste disposal system simulations. A paradigm shift

    International Nuclear Information System (INIS)

    Sheng, G.M.

    1994-01-01

    This work reviewed the current concept of nuclear waste disposal in stable, terrestrial geologic media with a system of natural and man-made multi-barriers. Various aspects of this concept and supporting research were examined with the emphasis on the Canadian Nuclear Fuel Waste Management Program. Several of the crucial issues and challenges facing the current concept were discussed. These include: The difficulties inherent in a concept that centres around lithologic studies; the unsatisfactory state of software quality assurance in the present computer simulation programs; and the lack of a standardized, comprehensive, and systematic procedure to carry out a rigorous process of model validation and assessment of simulation studies. An outline of such an approach was presented and some of the principles, tools and techniques for software verification were introduced and described. A case study involving an evaluation of the Canadian performance assessment computer program is presented. A new paradigm to nuclear waste disposal was advocated to address the challenges facing the existing concept. The RRC (Regional Recharge Concept) was introduced and its many advantages were described and shown through a modelling exercise. (orig./HP)

  15. Present status of an integrated software system for HASP (Human Acts Simulation Program)

    International Nuclear Information System (INIS)

    Otani, Takayuki; Ebihara, Ken-ichi; Kambayashi, Shaw; Kume, Etsuo; Higuchi, Kenji; Fujii, Minoru; Akimoto, Masayuki

    1994-01-01

    In Human Acts Simulation Program (HASP), human acts to be realized by a human-shaped intelligent robot in a nuclear power plant are simulated by computers. The major purpose of HASP is to develop basic and underlying design technologies for intelligent and automatic power plant. The objectives of this paper is to show the present status of the HASP, with particular emphasis on activities targetted at the integration of developed subsystems to simulate the important capabilities of the intelligent robot such as planning, robot dynamics, and so on. (author)

  16. The ATLAS Trigger Simulation with Legacy Software

    CERN Document Server

    Bernius, Catrin; The ATLAS collaboration

    2017-01-01

    Physics analyses at the LHC require accurate simulations of the detector response and the event selection processes, generally done with the most recent software releases. The trigger response simulation is crucial for determination of overall selection efficiencies and signal sensitivities and should be done with the same software release with which data were recorded. This requires potentially running with software dating many years back, the so-called legacy software. Therefore having a strategy for running legacy software in a modern environment becomes essential when data simulated for past years start to present a sizeable fraction of the total. The requirements and possibilities for such a simulation scheme within the ATLAS software framework were examined and a proof-of-concept simulation chain has been successfully implemented. One of the greatest challenges was the choice of a data format which promises long term compatibility with old and new software releases. Over the time periods envisaged, data...

  17. Assessing multizone airflow simulation software

    International Nuclear Information System (INIS)

    Lorenzetti, D.M.

    2002-01-01

    Several standard multizone modeling programs, in order to improve their computational efficiency, make a number of simplifying assumptions. This paper examines how those assumptions reduce the solution times and memory use of the programs, but at the cost of restricting the models they can express. Applications where these restrictions may adversely affect the program's usefulness include: (1) natural ventilation, when buoyancy effects dominate mechanically-driven flow; (2) duct system design, when losses in T-junctions affect the system performance; and (3) control system design, when the dynamic transport of pollutants plays a significant role in the simulated system

  18. Development of micro pattern cutting simulation software

    International Nuclear Information System (INIS)

    Lee, Jong Min; Song, Seok Gyun; Choi, Jeong Ju; Novandy, Bondhan; Kim, Su Jin; Lee, Dong Yoon; Nam, Sung Ho; Je, Tae Jin

    2008-01-01

    The micro pattern machining on the surface of wide mold is not easy to be simulated by conventional software. In this paper, a software is developed for micro pattern cutting simulation. The 3d geometry of v-groove, rectangular groove, pyramid and pillar patterns are visualized by c++ and OpenGL library. The micro cutting force is also simulated for each pattern

  19. Space Telescope Pointing Control System software

    Science.gov (United States)

    Dougherty, H.; Rodoni, C.; Rossini, R.; Tompetrini, K.; Nakashima, A.; Bradley, A.

    1982-01-01

    The Space Telescope Pointing Control System software is in the advanced development stage, having been tested on both the airbearing and the static simulator. The overall structure of the software is discussed, along with timing and sizing evaluations. The interaction between the controls analysts and software designer is described.

  20. ArcNLET: A GIS-based software to simulate groundwater nitrate load from septic systems to surface water bodies

    Science.gov (United States)

    Rios, J. Fernando; Ye, Ming; Wang, Liying; Lee, Paul Z.; Davis, Hal; Hicks, Rick

    2013-03-01

    Onsite wastewater treatment systems (OWTS), or septic systems, can be a significant source of nitrates in groundwater and surface water. The adverse effects that nitrates have on human and environmental health have given rise to the need to estimate the actual or potential level of nitrate contamination. With the goal of reducing data collection and preparation costs, and decreasing the time required to produce an estimate compared to complex nitrate modeling tools, we developed the ArcGIS-based Nitrate Load Estimation Toolkit (ArcNLET) software. Leveraging the power of geographic information systems (GIS), ArcNLET is an easy-to-use software capable of simulating nitrate transport in groundwater and estimating long-term nitrate loads from groundwater to surface water bodies. Data requirements are reduced by using simplified models of groundwater flow and nitrate transport which consider nitrate attenuation mechanisms (subsurface dispersion and denitrification) as well as spatial variability in the hydraulic parameters and septic tank distribution. ArcNLET provides a spatial distribution of nitrate plumes from multiple septic systems and a load estimate to water bodies. ArcNLET's conceptual model is divided into three sub-models: a groundwater flow model, a nitrate transport and fate model, and a load estimation model which are implemented as an extension to ArcGIS. The groundwater flow model uses a map of topography in order to generate a steady-state approximation of the water table. In a validation study, this approximation was found to correlate well with a water table produced by a calibrated numerical model although it was found that the degree to which the water table resembles the topography can vary greatly across the modeling domain. The transport model uses a semi-analytical solution to estimate the distribution of nitrate within groundwater, which is then used to estimate a nitrate load using a mass balance argument. The estimates given by ArcNLET are

  1. The ATLAS Trigger Simulation with Legacy Software

    CERN Document Server

    Bernius, Catrin; The ATLAS collaboration

    2017-01-01

    Physics analyses at the LHC which search for rare physics processes or measure Standard Model parameters with high precision require accurate simulations of the detector response and the event selection processes. The accurate simulation of the trigger response is crucial for determination of overall selection efficiencies and signal sensitivities. For the generation and the reconstruction of simulated event data, generally the most recent software releases are used to ensure the best agreement between simulated data and real data. For the simulation of the trigger selection process, however, the same software release with which real data were taken should be ideally used. This requires potentially running with software dating many years back, the so-called legacy software. Therefore having a strategy for running legacy software in a modern environment becomes essential when data simulated for past years start to present a sizeable fraction of the total. The requirements and possibilities for such a simulatio...

  2. Evaluation of Fluent Software for Simulation and Costruction of a Variable Rate Sprinkler for an Autonomous Irrigation System

    Directory of Open Access Journals (Sweden)

    H Roshan

    2014-09-01

    Full Text Available Water scarcity is today’s world biggest challenge which requires different countries to manage their water resources in the most efficient way. Sprinkler irrigation increases water consumption efficiency due to more uniform distribution of water across the field. Precision farming is based on the site-specific use of inputs according to soil characteristics and plant needs. One of the main inputs for agricultural production is water. Thus, efficient use of water resources based on variable rate irrigation is considered to be a basic approach of precision irrigation. The main purpose of this study was to simulate and fabricate a variable flow sprinkler, applicable in solid set sprinkler irrigation system. The preliminary drawing of the proposed sprinkler, which equipped with a flow and pressure control plunger, was simulated using Fluent software. The actual sprinkler was then fabricated and evaluated in a field. The performance of the sprinkler was evaluated at three pressure levels, three plunger positions (at the points of the least and biggest sprinkler’s cross section for water passage and three diameters of outlet nozzle opening. Results showed that the plunger had the capability of varying outlet flow and pressure in the sprinkler and trends in flow and pressure variation as affected by the plunger position was very complicated. The Fluent model for conditions with fully open of the plunger and half opened was effectively efficient. However, as the plunger closed the water passage more than the half of cross section, the model did not show an acceptable efficiency.

  3. Unified Engineering Software System

    Science.gov (United States)

    Purves, L. R.; Gordon, S.; Peltzman, A.; Dube, M.

    1989-01-01

    Collection of computer programs performs diverse functions in prototype engineering. NEXUS, NASA Engineering Extendible Unified Software system, is research set of computer programs designed to support full sequence of activities encountered in NASA engineering projects. Sequence spans preliminary design, design analysis, detailed design, manufacturing, assembly, and testing. Primarily addresses process of prototype engineering, task of getting single or small number of copies of product to work. Written in FORTRAN 77 and PROLOG.

  4. Lean Development with the Morpheus Simulation Software

    Science.gov (United States)

    Brogley, Aaron C.

    2013-01-01

    The Morpheus project is an autonomous robotic testbed currently in development at NASA's Johnson Space Center (JSC) with support from other centers. Its primary objectives are to test new 'green' fuel propulsion systems and to demonstrate the capability of the Autonomous Lander Hazard Avoidance Technology (ALHAT) sensor, provided by the Jet Propulsion Laboratory (JPL) on a lunar landing trajectory. If successful, these technologies and lessons learned from the Morpheus testing cycle may be incorporated into a landing descent vehicle used on the moon, an asteroid, or Mars. In an effort to reduce development costs and cycle time, the project employs lean development engineering practices in its development of flight and simulation software. The Morpheus simulation makes use of existing software packages where possible to reduce the development time. The development and testing of flight software occurs primarily through the frequent test operation of the vehicle and incrementally increasing the scope of the test. With rapid development cycles, risk of loss of the vehicle and loss of the mission are possible, but efficient progress in development would not be possible without that risk.

  5. Cluster computing software for GATE simulations

    International Nuclear Information System (INIS)

    Beenhouwer, Jan de; Staelens, Steven; Kruecker, Dirk; Ferrer, Ludovic; D'Asseler, Yves; Lemahieu, Ignace; Rannou, Fernando R.

    2007-01-01

    Geometry and tracking (GEANT4) is a Monte Carlo package designed for high energy physics experiments. It is used as the basis layer for Monte Carlo simulations of nuclear medicine acquisition systems in GEANT4 Application for Tomographic Emission (GATE). GATE allows the user to realistically model experiments using accurate physics models and time synchronization for detector movement through a script language contained in a macro file. The downside of this high accuracy is long computation time. This paper describes a platform independent computing approach for running GATE simulations on a cluster of computers in order to reduce the overall simulation time. Our software automatically creates fully resolved, nonparametrized macros accompanied with an on-the-fly generated cluster specific submit file used to launch the simulations. The scalability of GATE simulations on a cluster is investigated for two imaging modalities, positron emission tomography (PET) and single photon emission computed tomography (SPECT). Due to a higher sensitivity, PET simulations are characterized by relatively high data output rates that create rather large output files. SPECT simulations, on the other hand, have lower data output rates but require a long collimator setup time. Both of these characteristics hamper scalability as a function of the number of CPUs. The scalability of PET simulations is improved here by the development of a fast output merger. The scalability of SPECT simulations is improved by greatly reducing the collimator setup time. Accordingly, these two new developments result in higher scalability for both PET and SPECT simulations and reduce the computation time to more practical values

  6. Using modern software tools to design, simulate and test a Level 1 trigger sub-system for the D Zero Detector

    International Nuclear Information System (INIS)

    Angstadt, R.; Borcherding, F.; Johnson, M.E.; Moreira, L.

    1995-06-01

    This paper describes a system which uses a commercial spreadsheet program and commercial hardware on an IBM PC to develop and test a track finding system for the D Zero Level 1 scintillating Fiber Trigger. The trigger system resides in a VME crate. This system allows the user to generate test input, write the pattern to the hardware simulate the results in software, read the hardware result: compare the results and inform the user of any differences

  7. Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation, volume 2, part 1. Appendix A: Software documentation

    Science.gov (United States)

    Lowrie, J. W.; Fermelia, A. J.; Haley, D. C.; Gremban, K. D.; Vanbaalen, J.; Walsh, R. W.

    1982-01-01

    Documentation of the preliminary software developed as a framework for a generalized integrated robotic system simulation is presented. The program structure is composed of three major functions controlled by a program executive. The three major functions are: system definition, analysis tools, and post processing. The system definition function handles user input of system parameters and definition of the manipulator configuration. The analysis tools function handles the computational requirements of the program. The post processing function allows for more detailed study of the results of analysis tool function executions. Also documented is the manipulator joint model software to be used as the basis of the manipulator simulation which will be part of the analysis tools capability.

  8. Software for microcircuit systems

    International Nuclear Information System (INIS)

    Kunz, P.F.

    1978-10-01

    Modern Large Scale Integration (LSI) microcircuits are meant to be programed in order to control the function that they perform. The basics of microprograming and new microcircuits have already been discussed. In this course, the methods of developing software for these microcircuits are explored. This generally requires a package of support software in order to assemble the microprogram, and also some amount of support software to test the microprograms and to test the microprogramed circuit itself. 15 figures, 2 tables

  9. An IP-Based Software System for Real-time, Closed Loop, Multi-Spacecraft Mission Simulations

    Science.gov (United States)

    Cary, Everett; Davis, George; Higinbotham, John; Burns, Richard; Hogie, Keith; Hallahan, Francis

    2003-01-01

    This viewgraph presentation provides information on the architecture of a computerized testbest for simulating Distributed Space Systems (DSS) for controlling spacecraft flying in formation. The presentation also discusses and diagrams the Distributed Synthesis Environment (DSE) for simulating and planning DSS missions.

  10. Software for Engineering Simulations of a Spacecraft

    Science.gov (United States)

    Shireman, Kirk; McSwain, Gene; McCormick, Bernell; Fardelos, Panayiotis

    2005-01-01

    Spacecraft Engineering Simulation II (SES II) is a C-language computer program for simulating diverse aspects of operation of a spacecraft characterized by either three or six degrees of freedom. A functional model in SES can include a trajectory flight plan; a submodel of a flight computer running navigational and flight-control software; and submodels of the environment, the dynamics of the spacecraft, and sensor inputs and outputs. SES II features a modular, object-oriented programming style. SES II supports event-based simulations, which, in turn, create an easily adaptable simulation environment in which many different types of trajectories can be simulated by use of the same software. The simulation output consists largely of flight data. SES II can be used to perform optimization and Monte Carlo dispersion simulations. It can also be used to perform simulations for multiple spacecraft. In addition to its generic simulation capabilities, SES offers special capabilities for space-shuttle simulations: for this purpose, it incorporates submodels of the space-shuttle dynamics and a C-language version of the guidance, navigation, and control components of the space-shuttle flight software.

  11. SPINning parallel systems software

    International Nuclear Information System (INIS)

    Matlin, O.S.; Lusk, E.; McCune, W.

    2002-01-01

    We describe our experiences in using Spin to verify parts of the Multi Purpose Daemon (MPD) parallel process management system. MPD is a distributed collection of processes connected by Unix network sockets. MPD is dynamic processes and connections among them are created and destroyed as MPD is initialized, runs user processes, recovers from faults, and terminates. This dynamic nature is easily expressible in the Spin/Promela framework but poses performance and scalability challenges. We present here the results of expressing some of the parallel algorithms of MPD and executing both simulation and verification runs with Spin

  12. Software for Simulation of Hyperspectral Images

    Science.gov (United States)

    Richtsmeier, Steven C.; Singer-Berk, Alexander; Bernstein, Lawrence S.

    2002-01-01

    A package of software generates simulated hyperspectral images for use in validating algorithms that generate estimates of Earth-surface spectral reflectance from hyperspectral images acquired by airborne and spaceborne instruments. This software is based on a direct simulation Monte Carlo approach for modeling three-dimensional atmospheric radiative transport as well as surfaces characterized by spatially inhomogeneous bidirectional reflectance distribution functions. In this approach, 'ground truth' is accurately known through input specification of surface and atmospheric properties, and it is practical to consider wide variations of these properties. The software can treat both land and ocean surfaces and the effects of finite clouds with surface shadowing. The spectral/spatial data cubes computed by use of this software can serve both as a substitute for and a supplement to field validation data.

  13. Software for microcircuit systems

    International Nuclear Information System (INIS)

    Kunz, P.F.

    1978-01-01

    Modern Large Scale Integration (LSI) microcircuits are meant to be programmed in order to control the function that they perform. In the previous paper the author has already discussed the basics of microprogramming and have studied in some detail two types of new microcircuits. In this paper, methods of developing software for these microcircuits are explored. This generally requires a package of support software in order to assemble the microprogram, and also some amount of support software to test the microprograms and to test the microprogrammed circuit itself. (Auth.)

  14. Comparative Validation of Building Simulation Software

    DEFF Research Database (Denmark)

    Kalyanova, Olena; Heiselberg, Per

    The scope of this subtask is to perform a comparative validation of the building simulation software for the buildings with the double skin façade. The outline of the results in the comparative validation identifies the areas where is no correspondence achieved, i.e. calculation of the air flow r...... is that the comparative validation can be regarded as the main argument to continue the validation of the building simulation software for the buildings with the double skin façade with the empirical validation test cases.......The scope of this subtask is to perform a comparative validation of the building simulation software for the buildings with the double skin façade. The outline of the results in the comparative validation identifies the areas where is no correspondence achieved, i.e. calculation of the air flow...

  15. Distributed co-simulation of embedded control software with exhaust gas recirculation water handling system using INTO-CPS

    DEFF Research Database (Denmark)

    Pedersen, Nicolai; Lausdahl, Kenneth; Sanchez, Enrique Vidal

    2017-01-01

    to reduce the overall costs of validation. This paper demonstrates how this can be achieved for a commercial system developed by MAN Diesel & Turbo using a newly developed tool chain based on the Functional Mock-up Interface standard for co-simulation supporting different operating systems. The generality...

  16. Recommendation systems in software engineering

    CERN Document Server

    Robillard, Martin P; Walker, Robert J; Zimmermann, Thomas

    2014-01-01

    With the growth of public and private data stores and the emergence of off-the-shelf data-mining technology, recommendation systems have emerged that specifically address the unique challenges of navigating and interpreting software engineering data.This book collects, structures and formalizes knowledge on recommendation systems in software engineering. It adopts a pragmatic approach with an explicit focus on system design, implementation, and evaluation. The book is divided into three parts: "Part I - Techniques" introduces basics for building recommenders in software engineering, including techniques for collecting and processing software engineering data, but also for presenting recommendations to users as part of their workflow.?"Part II - Evaluation" summarizes methods and experimental designs for evaluating recommendations in software engineering.?"Part III - Applications" describes needs, issues and solution concepts involved in entire recommendation systems for specific software engineering tasks, fo...

  17. System support software for TSTA

    International Nuclear Information System (INIS)

    Claborn, G.W.; Mann, L.W.; Nielson, C.W.

    1987-01-01

    The software at the Tritium Systems Test Assembly (TSTA) is logically broken into two parts, the system support software and the subsystem software. The purpose of the system support software is to isolate the subsystem software from the physical hardware. In this sense the system support software forms the kernel of the software at TSTA. The kernel software performs several functions. It gathers data from CAMAC modules and makes that data available for subsystem processes. It services requests to send commands to CAMAC modules. It provides a system of logging functions and provides for a system-wide global program state that allows highly structured interaction between subsystem processes. The kernel's most visible function is to provide the Man-Machine Interface (MMI). The MMI allows the operators a window into the physical hardware and subsystem process state. Finally the kernel provides a data archiving and compression function that allows archival data to be accessed and plotted. Such kernel software as developed and implemented at TSTA is described

  18. Westinghouse waste simulation and optimization software tool

    International Nuclear Information System (INIS)

    Mennicken, Kim; Aign, Jorg

    2013-01-01

    Applications for dynamic simulation can be found in virtually all areas of process engineering. The tangible benefits of using dynamic simulation can be seen in tighter design, smoother start-ups and optimized operation. Thus, proper implementation of dynamic simulation can deliver substantial benefits. These benefits are typically derived from improved process understanding. Simulation gives confidence in evidence based decisions and enables users to try out lots of 'what if' scenarios until one is sure that a decision is the right one. In radioactive waste treatment tasks different kinds of waste with different volumes and properties have to be treated, e.g. from NPP operation or D and D activities. Finding a commercially and technically optimized waste treatment concept is a time consuming and difficult task. The Westinghouse Waste Simulation and Optimization Software Tool will enable the user to quickly generate reliable simulation models of various process applications based on equipment modules. These modules can be built with ease and be integrated into the simulation model. This capability ensures that this tool is applicable to typical waste treatment tasks. The identified waste streams and the selected treatment methods are the basis of the simulation and optimization software. After implementing suitable equipment data into the model, process requirements and waste treatment data are fed into the simulation to finally generate primary simulation results. A sensitivity analysis of automated optimization features of the software generates the lowest possible lifecycle cost for the simulated waste stream. In combination with proven waste management equipments and integrated waste management solutions, this tool provides reliable qualitative results that lead to an effective planning and minimizes the total project planning risk of any waste management activity. It is thus the ideal tool for designing a waste treatment facility in an optimum manner

  19. Westinghouse waste simulation and optimization software tool

    Energy Technology Data Exchange (ETDEWEB)

    Mennicken, Kim; Aign, Jorg [Westinghouse Electric Germany GmbH, Hamburg (Germany)

    2013-07-01

    Applications for dynamic simulation can be found in virtually all areas of process engineering. The tangible benefits of using dynamic simulation can be seen in tighter design, smoother start-ups and optimized operation. Thus, proper implementation of dynamic simulation can deliver substantial benefits. These benefits are typically derived from improved process understanding. Simulation gives confidence in evidence based decisions and enables users to try out lots of 'what if' scenarios until one is sure that a decision is the right one. In radioactive waste treatment tasks different kinds of waste with different volumes and properties have to be treated, e.g. from NPP operation or D and D activities. Finding a commercially and technically optimized waste treatment concept is a time consuming and difficult task. The Westinghouse Waste Simulation and Optimization Software Tool will enable the user to quickly generate reliable simulation models of various process applications based on equipment modules. These modules can be built with ease and be integrated into the simulation model. This capability ensures that this tool is applicable to typical waste treatment tasks. The identified waste streams and the selected treatment methods are the basis of the simulation and optimization software. After implementing suitable equipment data into the model, process requirements and waste treatment data are fed into the simulation to finally generate primary simulation results. A sensitivity analysis of automated optimization features of the software generates the lowest possible lifecycle cost for the simulated waste stream. In combination with proven waste management equipments and integrated waste management solutions, this tool provides reliable qualitative results that lead to an effective planning and minimizes the total project planning risk of any waste management activity. It is thus the ideal tool for designing a waste treatment facility in an optimum manner

  20. Distributed co-simulation of embedded control software with exhaust gas recirculation water handling system using INTO-CPS

    DEFF Research Database (Denmark)

    Pedersen, Nicolai; Lausdahl, Kenneth; Sanchez, Enrique Vidal

    2017-01-01

    properties is often desirable. However, it is non-trivial to be able to combine such different models of different constituent elements. In order to reduce the need for expensive tests on the real system it is advantageous to be able to combine such heterogeneous models in a joint co-simulation in order...

  1. Multi-Level Formation of Complex Software Systems

    Directory of Open Access Journals (Sweden)

    Hui Li

    2016-05-01

    Full Text Available We present a multi-level formation model for complex software systems. The previous works extract the software systems to software networks for further studies, but usually investigate the software networks at the class level. In contrast to these works, our treatment of software systems as multi-level networks is more realistic. In particular, the software networks are organized by three levels of granularity, which represents the modularity and hierarchy in the formation process of real-world software systems. More importantly, simulations based on this model have generated more realistic structural properties of software networks, such as power-law, clustering and modularization. On the basis of this model, how the structure of software systems effects software design principles is then explored, and it could be helpful for understanding software evolution and software engineering practices.

  2. Software Platform Evaluation - Verifiable Fuel Cycle Simulation (VISION) Model

    International Nuclear Information System (INIS)

    J. J. Jacobson; D. E. Shropshire; W. B. West

    2005-01-01

    The purpose of this Software Platform Evaluation (SPE) is to document the top-level evaluation of potential software platforms on which to construct a simulation model that satisfies the requirements for a Verifiable Fuel Cycle Simulation Model (VISION) of the Advanced Fuel Cycle (AFC). See the Software Requirements Specification for Verifiable Fuel Cycle Simulation (VISION) Model (INEEL/EXT-05-02643, Rev. 0) for a discussion of the objective and scope of the VISION model. VISION is intended to serve as a broad systems analysis and study tool applicable to work conducted as part of the AFCI (including costs estimates) and Generation IV reactor development studies. This document will serve as a guide for selecting the most appropriate software platform for VISION. This is a ''living document'' that will be modified over the course of the execution of this work

  3. Simulator testing system (STS)

    International Nuclear Information System (INIS)

    Miller, V.N.

    1990-01-01

    In recent years there has been a greater demand placed on the capabilities and time usage of real-time nuclear plant simulators due to NRC, INPO and utilities requirements. The requirements applied to certification, new simulators, upgrades, modifications, and maintenance of the simulators vary; however, they all require the capabilities of the simulator to be tested whether it is for NRC 10CFR55.45b requirements, ATP testing of new simulators, ATP testing of upgrades with or without panels, adding software/hardware due to plant modifications, or analyzing software/hardware problems on the simulator. This paper describes the Simulator Testing System (STS) which addresses each one of these requirements placed on simulators. Special attention will be given to ATP testing of upgrades without the use of control room panels. The capabilities and applications of the four parts of STS which are the Display Control Software (DCS), Procedure Control Software (PCS), Display Generator Software (DGS) and the Procedure Generator Software (PGS) will be reviewed

  4. Software design for resilient computer systems

    CERN Document Server

    Schagaev, Igor

    2016-01-01

    This book addresses the question of how system software should be designed to account for faults, and which fault tolerance features it should provide for highest reliability. The authors first show how the system software interacts with the hardware to tolerate faults. They analyze and further develop the theory of fault tolerance to understand the different ways to increase the reliability of a system, with special attention on the role of system software in this process. They further develop the general algorithm of fault tolerance (GAFT) with its three main processes: hardware checking, preparation for recovery, and the recovery procedure. For each of the three processes, they analyze the requirements and properties theoretically and give possible implementation scenarios and system software support required. Based on the theoretical results, the authors derive an Oberon-based programming language with direct support of the three processes of GAFT. In the last part of this book, they introduce a simulator...

  5. ALICES: an advanced object-oriented software workshop for simulators

    International Nuclear Information System (INIS)

    Sayet, R.L.; Rouault, G.; Pieroux, D.; Houte, U. Van

    1999-01-01

    Reducing simulator development costs while improving model quality, user-friendliness and teaching capabilities, is a major target for many years in the simulation industry. It has led to the development of specific software tools which have been improved progressively following the new features and capabilities offered by the software industry. Unlike most of these software tools, ALICES (which is a French acronym for 'Interactive Software Workshop for the Design of Simulators') is not an upgrade of a previous generation of tools, like putting a graphical front-end to a classical code generator, but a really new development. Its design specification is based on previous experience with different tools as well as on new capabilities of software technology, mainly in Object Oriented Design. This allowed us to make a real technological 'jump' in the simulation industry, beyond the constraints of some traditional approaches. The main objectives behind the development of ALICES were the following: (1) Minimizing the simulator development time and costs: a simulator development consists mainly in developing software. One way to reduce costs is to facilitate reuse of existing software by developing standard components, and by defining interface standards, (2) Insuring that the produced simulator can be maintained and updated at a minimal cost: a simulator must evolve along with the simulated process, and it is then necessary to update periodically the simulator. The cost of an adequate maintenance is highly dependent of the quality of the software workshop, (3) Covering the whole simulator development process: from the data package to the acceptance tests and for maintenance and upgrade activities; with the whole development team, even if it is dispatched at different working sites; respecting the Quality Assurance rules and procedures (CORYS T.E.S.S. and TRACTEBEL are ISO-9001 certified). The development of ALICES was also done to comply with the following two main

  6. Simulation software: engineer processes before reengineering.

    Science.gov (United States)

    Lepley, C J

    2001-01-01

    People make decisions all the time using intuition. But what happens when you are asked: "Are you sure your predictions are accurate? How much will a mistake cost? What are the risks associated with this change?" Once a new process is engineered, it is difficult to analyze what would have been different if other options had been chosen. Simulating a process can help senior clinical officers solve complex patient flow problems and avoid wasted efforts. Simulation software can give you the data you need to make decisions. The author introduces concepts, methodologies, and applications of computer aided simulation to illustrate their use in making decisions to improve workflow design.

  7. Analysis and design of the SI-simulator software system for the VHTR-SI process by using the object-oriented analysis and object-oriented design methodology

    International Nuclear Information System (INIS)

    Chang, Jiwoon; Shin, Youngjoon; Kim, Jihwan; Lee, Kiyoung; Lee, Wonjae; Chang, Jonghwa; Youn, Cheung

    2008-01-01

    The SI-simulator is an application software system that simulates the dynamic behavior of the VHTR-SI process by the use of mathematical models. Object-oriented analysis (OOA) and object-oriented design (OOD) methodologies were employed for the SI simulator system development. OOA is concerned with developing software engineering requirements and specifications that are expressed as a system's object model (which is composed of a population of interacting objects), as opposed to the traditional data or functional views of systems. OOD techniques are useful for the development of large complex systems. Also, OOA/OOD methodology is usually employed to maximize the reusability and extensibility of a software system. In this paper, we present a design feature for the SI simulator software system by the using methodologies of OOA and OOD

  8. Software Build and Delivery Systems

    Energy Technology Data Exchange (ETDEWEB)

    Robey, Robert W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-07-10

    This presentation deals with the hierarchy of software build and delivery systems. One of the goals is to maximize the success rate of new users and developers when first trying your software. First impressions are important. Early successes are important. This also reduces critical documentation costs. This is a presentation focused on computer science and goes into detail about code documentation.

  9. Interactive Dynamic-System Simulation

    CERN Document Server

    Korn, Granino A

    2010-01-01

    Showing you how to use personal computers for modeling and simulation, Interactive Dynamic-System Simulation, Second Edition provides a practical tutorial on interactive dynamic-system modeling and simulation. It discusses how to effectively simulate dynamical systems, such as aerospace vehicles, power plants, chemical processes, control systems, and physiological systems. Written by a pioneer in simulation, the book introduces dynamic-system models and explains how software for solving differential equations works. After demonstrating real simulation programs with simple examples, the author

  10. Selection of a Data Acquisition and Controls System Communications and Software Architecture for Johnson Space Center's Space Environment Simulation Laboratory Thermal and Vacuum Test Facilities

    Science.gov (United States)

    Jordan, Eric A.

    2004-01-01

    Upgrade of data acquisition and controls systems software at Johnson Space Center's Space Environment Simulation Laboratory (SESL) involved the definition, evaluation and selection of a system communication architecture and software components. A brief discussion of the background of the SESL and its data acquisition and controls systems provides a context for discussion of the requirements for each selection. Further framework is provided as upgrades to these systems accomplished in the 1990s and in 2003 are compared to demonstrate the role that technological advances have had in their improvement. Both of the selections were similar in their three phases; 1) definition of requirements, 2) identification of candidate products and their evaluation and testing and 3) selection by comparison of requirement fulfillment. The candidates for the communication architecture selection embraced several different methodologies which are explained and contrasted. Requirements for this selection are presented and the selection process is described. Several candidates for the software component of the data acquisition and controls system are identified, requirements for evaluation and selection are presented, and the evaluation process is described.

  11. System Software 7 Macintosh

    CERN Multimedia

    1991-01-01

    System 7 is a single-user graphical user interface-based operating system for Macintosh computers and was part of the classic Mac OS line of operating systems. It was introduced on May 13, 1991, by Apple Computer. It succeeded System 6, and was the main Macintosh operating system until it was succeeded by Mac OS 8 in 1997. Features added with the System 7 release included virtual memory, personal file sharing, QuickTime, QuickDraw 3D, and an improved user interface. This is the first real major evolution of the Macintosh system, bringing a significant improvement in the user interface, improved stability and many new features such as the ability to use multiple applications at the same time. "System 7" is the last operating system name of the Macintosh that contains the word "system". Macintosh operating systems were later called "Mac OS" (for Macintosh Operating System).

  12. Claire, a simulation and testing tool for critical softwares

    International Nuclear Information System (INIS)

    Gassino, J.; Henry, J.Y.

    1996-01-01

    The CEA and IPSN (Institute of Nuclear Protection and Safety) needs concerning the testing of critical softwares, have led to the development of the CLAIRE tool which is able to test the softwares without modification. This tool allows to graphically model the system and its environment and to include components into the model which observe and do not modify the behaviour of the system to be tested. The executable codes are integrated in the model. The tool uses target machine simulators (microprocessors). The technique used (the event simulation) allows to associate actions with events such as the execution of an instruction, the access to a variable etc.. The simulation results are exploited using graphic, states research and test cover measurement tools. In particular, this tool can give help to the evaluation of critical softwares with pre-existing components. (J.S.)

  13. A computational systems biology software platform for multiscale modeling and simulation: Integrating whole-body physiology, disease biology, and molecular reaction networks

    Directory of Open Access Journals (Sweden)

    Thomas eEissing

    2011-02-01

    Full Text Available Today, in silico studies and trial simulations already complement experimental approaches in pharmaceutical R&D and have become indispensable tools for decision making and communication with regulatory agencies. While biology is multi-scale by nature, project work and software tools usually focus on isolated aspects of drug action, such as pharmacokinetics at the organism scale or pharmacodynamic interaction on the molecular level. We present a modeling and simulation software platform consisting of PK-Sim® and MoBi® capable of building and simulating models that integrate across biological scales. A prototypical multiscale model for the progression of a pancreatic tumor and its response to pharmacotherapy is constructed and virtual patients are treated with a prodrug activated by hepatic metabolization. Tumor growth is driven by signal transduction leading to cell cycle transition and proliferation. Free tumor concentrations of the active metabolite inhibit Raf kinase in the signaling cascade and thereby cell cycle progression. In a virtual clinical study, the individual therapeutic outcome of the chemotherapeutic intervention is simulated for a large population with heterogeneous genomic background. Thereby, the platform allows efficient model building and integration of biological knowledge and prior data from all biological scales. Experimental in vitro model systems can be linked with observations in animal experiments and clinical trials. The interplay between patients, diseases, and drugs and topics with high clinical relevance such as the role of pharmacogenomics, drug-drug or drug-metabolite interactions can be addressed using this mechanistic, insight driven multiscale modeling approach.

  14. Simulation Modeling of Software Development Processes

    Science.gov (United States)

    Calavaro, G. F.; Basili, V. R.; Iazeolla, G.

    1996-01-01

    A simulation modeling approach is proposed for the prediction of software process productivity indices, such as cost and time-to-market, and the sensitivity analysis of such indices to changes in the organization parameters and user requirements. The approach uses a timed Petri Net and Object Oriented top-down model specification. Results demonstrate the model representativeness, and its usefulness in verifying process conformance to expectations, and in performing continuous process improvement and optimization.

  15. REENGINEERING OF THE AIR SIMULATORS LEGACY SOFTWARE

    Directory of Open Access Journals (Sweden)

    Nikolay O. Sidorov

    2008-02-01

    Full Text Available  There are the technical complexes consisting of components, parts of which are actively used, but the rest has lost working capacity owing to moral and physical deterioration. An example of such a complex is the aviation-flight complex "plane-simulator". High cost of components which continue to be used (plane do the actual task of restoring and supporting the out-of-order components (simulator. The considerable part of such complexes is the software, which owing to replacement of the obsolete and physically worn out hardware requires the rework. The rework method is reengineering.

  16. A general software reliability process simulation technique

    Science.gov (United States)

    Tausworthe, Robert C.

    1991-01-01

    The structure and rationale of the generalized software reliability process, together with the design and implementation of a computer program that simulates this process are described. Given assumed parameters of a particular project, the users of this program are able to generate simulated status timelines of work products, numbers of injected anomalies, and the progress of testing, fault isolation, repair, validation, and retest. Such timelines are useful in comparison with actual timeline data, for validating the project input parameters, and for providing data for researchers in reliability prediction modeling.

  17. DigR: a generic model and its open source simulation software to mimic three-dimensional root-system architecture diversity.

    Science.gov (United States)

    Barczi, Jean-François; Rey, Hervé; Griffon, Sébastien; Jourdan, Christophe

    2018-04-18

    Many studies exist in the literature dealing with mathematical representations of root systems, categorized, for example, as pure structure description, partial derivative equations or functional-structural plant models. However, in these studies, root architecture modelling has seldom been carried out at the organ level with the inclusion of environmental influences that can be integrated into a whole plant characterization. We have conducted a multidisciplinary study on root systems including field observations, architectural analysis, and formal and mathematical modelling. This integrative and coherent approach leads to a generic model (DigR) and its software simulator. Architecture analysis applied to root systems helps at root type classification and architectural unit design for each species. Roots belonging to a particular type share dynamic and morphological characteristics which consist of topological and geometric features. The DigR simulator is integrated into the Xplo environment, with a user interface to input parameter values and make output ready for dynamic 3-D visualization, statistical analysis and saving to standard formats. DigR is simulated in a quasi-parallel computing algorithm and may be used either as a standalone tool or integrated into other simulation platforms. The software is open-source and free to download at http://amapstudio.cirad.fr/soft/xplo/download. DigR is based on three key points: (1) a root-system architectural analysis, (2) root type classification and modelling and (3) a restricted set of 23 root type parameters with flexible values indexed in terms of root position. Genericity and botanical accuracy of the model is demonstrated for growth, branching, mortality and reiteration processes, and for different root architectures. Plugin examples demonstrate the model's versatility at simulating plastic responses to environmental constraints. Outputs of the model include diverse root system structures such as tap

  18. Software Systems Stockroom

    Science.gov (United States)

    2009-11-01

    44  Figure 28: The Triples Report PHP Source .................................................................................. 46  iii...relational database management system (RDBMS). The RDBMS chosen for the S3 prototype is MySQL [9] due to its particular suitability for fronting database...backed websites. However, any RDBMS compliant with the Drupal content management system is suitable. S3 is developed primarily in the PHP

  19. The primary protection system software

    International Nuclear Information System (INIS)

    Tooley, P.A.

    1992-01-01

    This paper continues the detailed description of the Primary Protection System for Sizewell-B by providing an overview of design and implementation of the software, including the features of the design process which ensure that quality is delivered by the contractor. The Nuclear Electric software assessment activities are also described. The argument for the excellence of the software is made on the basis of a quality product delivered by the equipment supplier's design process, and the confirmation of this provided by the Nuclear Electric assessment process, which is as searching and complete an examination as is reasonably practicable to achieve. (author)

  20. Simulator configuration management system

    International Nuclear Information System (INIS)

    Faulent, J.; Brooks, J.G.

    1990-01-01

    The proposed revisions to ANS 3.5-1985 (Section 5) require Utilities to establish a simulator Configuration Management System (CMS). The proposed CMS must be capable of: Establishing and maintaining a simulator design database. Identifying and documenting differences between the simulator and its reference plant. Tracking the resolution of identified differences. Recording data to support simulator certification, testing and maintenance. This paper discusses a CMS capable of meeting the proposed requirements contained in ANS 3.5. The system will utilize a personal computer and a relational database management software to construct a simulator design database. The database will contain records to all reference nuclear plant data used in designing the simulator, as well as records identifying all the software, hardware and documentation making up the simulator. Using the relational powers of the database management software, reports will be generated identifying the impact of reference plant changes on the operation of the simulator. These reports can then be evaluated in terms of training needs to determine if changes are required for the simulator. If a change is authorized, the CMS will track the change through to its resolution and then incorporate the change into the simulator design database

  1. Software for natural gas pipeline design and simulation (gaspisim ...

    African Journals Online (AJOL)

    Software for natural gas pipeline design and simulation (gaspisim) ... This paper focuses on the development of software for optimum design and simulation of natural gas pipeline. General ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

  2. Resilient Software Systems

    Science.gov (United States)

    2015-06-01

    and tools, called model-integrated computing ( MIC ) [3] relies on the use of domain-specific modeling languages for creating models of the system to be...hence giving reflective capabilities to it. We have followed the MIC method here: we designed a domain- specific modeling language for modeling...are produced one-off and not for the mass market , the scope for price reduction based on the market demands is non-existent. Processes to create

  3. The Systems Biology Research Tool: evolvable open-source software

    OpenAIRE

    Wright, J; Wagner, A

    2008-01-01

    Abstract Background Research in the field of systems biology requires software for a variety of purposes. Software must be used to store, retrieve, analyze, and sometimes even to collect the data obtained from system-level (often high-throughput) experiments. Software must also be used to implement mathematical models and algorithms required for simulation and theoretical predictions on the system-level. Results We introduce a free, easy-to-use, open-source, integrated software platform calle...

  4. Method of software development for tasks of automatic control systems for simulation and designing on the base of the technological systems design data

    International Nuclear Information System (INIS)

    Ajzatulin, A.I.

    2007-01-01

    One studies the factors affecting the designing of the full-scale simulation facilities, the design data base simulation and the application of digital computerized process control systems. Paper describes problems dealing with the errors in the process system design data and the algorithm simulation methodological problems. On the basis of the records of the efforts to design the full-scale simulation facilities of the Tienvan NPP and of the Kudankulam NPP one brings to the notice a procedure to elaborate new tools to simulate and to elaborate algorithms for the computerized process control systems based on the process system design data. Paper lists the basic components of the program system under elaboration to ensure simulation and designing and describes their functions. The introduction result is briefly described [ru

  5. Computer systems and software engineering

    Science.gov (United States)

    Mckay, Charles W.

    1988-01-01

    The High Technologies Laboratory (HTL) was established in the fall of 1982 at the University of Houston Clear Lake. Research conducted at the High Tech Lab is focused upon computer systems and software engineering. There is a strong emphasis on the interrelationship of these areas of technology and the United States' space program. In Jan. of 1987, NASA Headquarters announced the formation of its first research center dedicated to software engineering. Operated by the High Tech Lab, the Software Engineering Research Center (SERC) was formed at the University of Houston Clear Lake. The High Tech Lab/Software Engineering Research Center promotes cooperative research among government, industry, and academia to advance the edge-of-knowledge and the state-of-the-practice in key topics of computer systems and software engineering which are critical to NASA. The center also recommends appropriate actions, guidelines, standards, and policies to NASA in matters pertinent to the center's research. Results of the research conducted at the High Tech Lab/Software Engineering Research Center have given direction to many decisions made by NASA concerning the Space Station Program.

  6. Experimental research control software system

    International Nuclear Information System (INIS)

    Cohn, I A; Kovalenko, A G; Vystavkin, A N

    2014-01-01

    A software system, intended for automation of a small scale research, has been developed. The software allows one to control equipment, acquire and process data by means of simple scripts. The main purpose of that development is to increase experiment automation easiness, thus significantly reducing experimental setup automation efforts. In particular, minimal programming skills are required and supervisors have no reviewing troubles. Interactions between scripts and equipment are managed automatically, thus allowing to run multiple scripts simultaneously. Unlike well-known data acquisition commercial software systems, the control is performed by an imperative scripting language. This approach eases complex control and data acquisition algorithms implementation. A modular interface library performs interaction with external interfaces. While most widely used interfaces are already implemented, a simple framework is developed for fast implementations of new software and hardware interfaces. While the software is in continuous development with new features being implemented, it is already used in our laboratory for automation of a helium-3 cryostat control and data acquisition. The software is open source and distributed under Gnu Public License.

  7. Experimental research control software system

    Science.gov (United States)

    Cohn, I. A.; Kovalenko, A. G.; Vystavkin, A. N.

    2014-05-01

    A software system, intended for automation of a small scale research, has been developed. The software allows one to control equipment, acquire and process data by means of simple scripts. The main purpose of that development is to increase experiment automation easiness, thus significantly reducing experimental setup automation efforts. In particular, minimal programming skills are required and supervisors have no reviewing troubles. Interactions between scripts and equipment are managed automatically, thus allowing to run multiple scripts simultaneously. Unlike well-known data acquisition commercial software systems, the control is performed by an imperative scripting language. This approach eases complex control and data acquisition algorithms implementation. A modular interface library performs interaction with external interfaces. While most widely used interfaces are already implemented, a simple framework is developed for fast implementations of new software and hardware interfaces. While the software is in continuous development with new features being implemented, it is already used in our laboratory for automation of a helium-3 cryostat control and data acquisition. The software is open source and distributed under Gnu Public License.

  8. Near-Earth Object Survey Simulation Software

    Science.gov (United States)

    Naidu, Shantanu P.; Chesley, Steven R.; Farnocchia, Davide

    2017-10-01

    There is a significant interest in Near-Earth objects (NEOs) because they pose an impact threat to Earth, offer valuable scientific information, and are potential targets for robotic and human exploration. The number of NEO discoveries has been rising rapidly over the last two decades with over 1800 being discovered last year, making the total number of known NEOs >16000. Pan-STARRS and the Catalina Sky Survey are currently the most prolific NEO surveys, having discovered >1600 NEOs between them in 2016. As next generation surveys such as Large Synoptic Survey Telescope (LSST) and the proposed Near-Earth Object Camera (NEOCam) become operational in the next decade, the discovery rate is expected to increase tremendously. Coordination between various survey telescopes will be necessary in order to optimize NEO discoveries and create a unified global NEO discovery network. We are collaborating on a community-based, open-source software project to simulate asteroid surveys to facilitate such coordination and develop strategies for improving discovery efficiency. Our effort so far has focused on development of a fast and efficient tool capable of accepting user-defined asteroid population models and telescope parameters such as a list of pointing angles and camera field-of-view, and generating an output list of detectable asteroids. The software takes advantage of the widely used and tested SPICE library and architecture developed by NASA’s Navigation and Ancillary Information Facility (Acton, 1996) for saving and retrieving asteroid trajectories and camera pointing. Orbit propagation is done using OpenOrb (Granvik et al. 2009) but future versions will allow the user to plug in a propagator of their choice. The software allows the simulation of both ground-based and space-based surveys. Performance is being tested using the Grav et al. (2011) asteroid population model and the LSST simulated survey “enigma_1189”.

  9. Parallel-Processing Test Bed For Simulation Software

    Science.gov (United States)

    Blech, Richard; Cole, Gary; Townsend, Scott

    1996-01-01

    Second-generation Hypercluster computing system is multiprocessor test bed for research on parallel algorithms for simulation in fluid dynamics, electromagnetics, chemistry, and other fields with large computational requirements but relatively low input/output requirements. Built from standard, off-shelf hardware readily upgraded as improved technology becomes available. System used for experiments with such parallel-processing concepts as message-passing algorithms, debugging software tools, and computational steering. First-generation Hypercluster system described in "Hypercluster Parallel Processor" (LEW-15283).

  10. Virtual Exercise Training Software System

    Science.gov (United States)

    Vu, L.; Kim, H.; Benson, E.; Amonette, W. E.; Barrera, J.; Perera, J.; Rajulu, S.; Hanson, A.

    2018-01-01

    The purpose of this study was to develop and evaluate a virtual exercise training software system (VETSS) capable of providing real-time instruction and exercise feedback during exploration missions. A resistive exercise instructional system was developed using a Microsoft Kinect depth-camera device, which provides markerless 3-D whole-body motion capture at a small form factor and minimal setup effort. It was hypothesized that subjects using the newly developed instructional software tool would perform the deadlift exercise with more optimal kinematics and consistent technique than those without the instructional software. Following a comprehensive evaluation in the laboratory, the system was deployed for testing and refinement in the NASA Extreme Environment Mission Operations (NEEMO) analog.

  11. Software Engineering for Scientific Computer Simulations

    Science.gov (United States)

    Post, Douglass E.; Henderson, Dale B.; Kendall, Richard P.; Whitney, Earl M.

    2004-11-01

    Computer simulation is becoming a very powerful tool for analyzing and predicting the performance of fusion experiments. Simulation efforts are evolving from including only a few effects to many effects, from small teams with a few people to large teams, and from workstations and small processor count parallel computers to massively parallel platforms. Successfully making this transition requires attention to software engineering issues. We report on the conclusions drawn from a number of case studies of large scale scientific computing projects within DOE, academia and the DoD. The major lessons learned include attention to sound project management including setting reasonable and achievable requirements, building a good code team, enforcing customer focus, carrying out verification and validation and selecting the optimum computational mathematics approaches.

  12. In Search of the Philosopher's Stone: Simulation Composability Versus Component-Based Software Design

    National Research Council Canada - National Science Library

    Bartholet, Robert G; Brogan, David C; Reynolds, Jr., Paul F; Carnahan, Joseph C

    2004-01-01

    The simulation community and the software engineering community are actively conducting research on technology that will make it possible to easily build complex systems by combining existing components...

  13. Packaging of control system software

    International Nuclear Information System (INIS)

    Zagar, K.; Kobal, M.; Saje, N.; Zagar, A.; Sabjan, R.; Di Maio, F.; Stepanov, D.

    2012-01-01

    Control system software consists of several parts - the core of the control system, drivers for integration of devices, configuration for user interfaces, alarm system, etc. Once the software is developed and configured, it must be installed to computers where it runs. Usually, it is installed on an operating system whose services it needs, and also in some cases dynamically links with the libraries it provides. Operating system can be quite complex itself - for example, a typical Linux distribution consists of several thousand packages. To manage this complexity, we have decided to rely on Red Hat Package Management system (RPM) to package control system software, and also ensure it is properly installed (i.e., that dependencies are also installed, and that scripts are run after installation if any additional actions need to be performed). As dozens of RPM packages need to be prepared, we are reducing the amount of effort and improving consistency between packages through a Maven-based infrastructure that assists in packaging (e.g., automated generation of RPM SPEC files, including automated identification of dependencies). So far, we have used it to package EPICS, Control System Studio (CSS) and several device drivers. We perform extensive testing on Red Hat Enterprise Linux 5.5, but we have also verified that packaging works on CentOS and Scientific Linux. In this article, we describe in greater detail the systematic system of packaging we are using, and its particular application for the ITER CODAC Core System. (authors)

  14. Software

    Energy Technology Data Exchange (ETDEWEB)

    Macedo, R.; Budd, G.; Ross, E.; Wells, P.

    2010-07-15

    The software section of this journal presented new software programs that have been developed to help in the exploration and development of hydrocarbon resources. Software provider IHS Inc. has made additions to its geological and engineering analysis software tool, IHS PETRA, a product used by geoscientists and engineers to visualize, analyze and manage well production, well log, drilling, reservoir, seismic and other related information. IHS PETRA also includes a directional well module and a decline curve analysis module to improve analysis capabilities in unconventional reservoirs. Petris Technology Inc. has developed a software to help manage the large volumes of data. PetrisWinds Enterprise (PWE) helps users find and manage wellbore data, including conventional wireline and MWD core data; analysis core photos and images; waveforms and NMR; and external files documentation. Ottawa-based Ambercore Software Inc. has been collaborating with Nexen on the Petroleum iQ software for steam assisted gravity drainage (SAGD) producers. Petroleum iQ integrates geology and geophysics data with engineering data in 3D and 4D. Calgary-based Envirosoft Corporation has developed a software that reduces the costly and time-consuming effort required to comply with Directive 39 of the Alberta Energy Resources Conservation Board. The product includes an emissions modelling software. Houston-based Seismic Micro-Technology (SMT) has developed the Kingdom software that features the latest in seismic interpretation. Holland-based Joa Oil and Gas and Calgary-based Computer Modelling Group have both supplied the petroleum industry with advanced reservoir simulation software that enables reservoir interpretation. The 2010 software survey included a guide to new software applications designed to facilitate petroleum exploration, drilling and production activities. Oil and gas producers can use the products for a range of functions, including reservoir characterization and accounting. In

  15. Software To Secure Distributed Propulsion Simulations

    Science.gov (United States)

    Blaser, Tammy M.

    2003-01-01

    Distributed-object computing systems are presented with many security threats, including network eavesdropping, message tampering, and communications middleware masquerading. NASA Glenn Research Center, and its industry partners, has taken an active role in mitigating the security threats associated with developing and operating their proprietary aerospace propulsion simulations. In particular, they are developing a collaborative Common Object Request Broker Architecture (CORBA) Security (CORBASec) test bed to secure their distributed aerospace propulsion simulations. Glenn has been working with its aerospace propulsion industry partners to deploy the Numerical Propulsion System Simulation (NPSS) object-based technology. NPSS is a program focused on reducing the cost and time in developing aerospace propulsion engines

  16. Software for graphic display systems

    International Nuclear Information System (INIS)

    Karlov, A.A.

    1978-01-01

    In this paper some aspects of graphic display systems are discussed. The design of a display subroutine library is described, with an example, and graphic dialogue software is considered primarily from the point of view of the programmer who uses a high-level language. (Auth.)

  17. Software metrics: Software quality metrics for distributed systems. [reliability engineering

    Science.gov (United States)

    Post, J. V.

    1981-01-01

    Software quality metrics was extended to cover distributed computer systems. Emphasis is placed on studying embedded computer systems and on viewing them within a system life cycle. The hierarchy of quality factors, criteria, and metrics was maintained. New software quality factors were added, including survivability, expandability, and evolvability.

  18. OST: analysis tool for real time software by simulation of material and software environments

    International Nuclear Information System (INIS)

    Boulc'h; Le Meur; Lapassat; Salichon; Segalard

    1988-07-01

    The utilization of microprocessors systems in a nuclear installation control oblige a great operation safety in the installation operation and in the environment protection. For the safety analysis of these installations the Institute of Protection and Nuclear Safety (IPSN) will dispose tools which permit to make controls during all the life of the software. The simulation and test tool (OST) which have been created is completely made by softwares. It is used on VAX calculators and can be easily transportable on other calculators [fr

  19. Automating software design system DESTA

    Science.gov (United States)

    Lovitsky, Vladimir A.; Pearce, Patricia D.

    1992-01-01

    'DESTA' is the acronym for the Dialogue Evolutionary Synthesizer of Turnkey Algorithms by means of a natural language (Russian or English) functional specification of algorithms or software being developed. DESTA represents the computer-aided and/or automatic artificial intelligence 'forgiving' system which provides users with software tools support for algorithm and/or structured program development. The DESTA system is intended to provide support for the higher levels and earlier stages of engineering design of software in contrast to conventional Computer Aided Design (CAD) systems which provide low level tools for use at a stage when the major planning and structuring decisions have already been taken. DESTA is a knowledge-intensive system. The main features of the knowledge are procedures, functions, modules, operating system commands, batch files, their natural language specifications, and their interlinks. The specific domain for the DESTA system is a high level programming language like Turbo Pascal 6.0. The DESTA system is operational and runs on an IBM PC computer.

  20. The economics of information systems and software

    CERN Document Server

    Veryard, Richard

    2014-01-01

    The Economics of Information Systems and Software focuses on the economic aspects of information systems and software, including advertising, evaluation of information systems, and software maintenance. The book first elaborates on value and values, software business, and scientific information as an economic category. Discussions focus on information products and information services, special economic properties of information, culture and convergence, hardware and software products, materiality and consumption, technological progress, and software flexibility. The text then takes a look at a

  1. Certification of digital system software

    International Nuclear Information System (INIS)

    Waclo, J.; Cook, B.; Adomaitis, D.

    1991-01-01

    The activities involved in the successful application of digital systems to Nuclear Protection functions is not achieved through happenstance. At Westinghouse there has been a longstanding program to utilize digital state of the art technology for protection system advancement. Thereby gaining the advantages of increased system reliability, performance, ease of operation and reduced maintenance costs. This paper describes the Westinghouse background and experience in the safety system software development process, including Verification and Validation, and its application to protection system qualification and the successful use for licensing the Eagle 21 Digital Process Protection System Upgrade. In addition, the lessons learned from this experience are discussed from the perspective of improving the development process through applying feedback of the measurements made on the process and the software product quality. The goal of this process optimization is to produce the highest possible software quality while recognizing the real world constraints of available resources, project schedule and the regulatory policies that are customary in the nuclear industry

  2. Freud: a software suite for high-throughput simulation analysis

    Science.gov (United States)

    Harper, Eric; Spellings, Matthew; Anderson, Joshua; Glotzer, Sharon

    Computer simulation is an indispensable tool for the study of a wide variety of systems. As simulations scale to fill petascale and exascale supercomputing clusters, so too does the size of the data produced, as well as the difficulty in analyzing these data. We present Freud, an analysis software suite for efficient analysis of simulation data. Freud makes no assumptions about the system being analyzed, allowing for general analysis methods to be applied to nearly any type of simulation. Freud includes standard analysis methods such as the radial distribution function, as well as new methods including the potential of mean force and torque and local crystal environment analysis. Freud combines a Python interface with fast, parallel C + + analysis routines to run efficiently on laptops, workstations, and supercomputing clusters. Data analysis on clusters reduces data transfer requirements, a prohibitive cost for petascale computing. Used in conjunction with simulation software, Freud allows for smart simulations that adapt to the current state of the system, enabling the study of phenomena such as nucleation and growth, intelligent investigation of phases and phase transitions, and determination of effective pair potentials.

  3. Using CONFIG for Simulation of Operation of Water Recovery Subsystems for Advanced Control Software Evaluation

    Science.gov (United States)

    Malin, Jane T.; Flores, Luis; Fleming, Land; Throop, Daiv

    2002-01-01

    A hybrid discrete/continuous simulation tool, CONFIG, has been developed to support evaluation of the operability life support systems. CON FIG simulates operations scenarios in which flows and pressures change continuously while system reconfigurations occur as discrete events. In simulations, intelligent control software can interact dynamically with hardware system models. CONFIG simulations have been used to evaluate control software and intelligent agents for automating life support systems operations. A CON FIG model of an advanced biological water recovery system has been developed to interact with intelligent control software that is being used in a water system test at NASA Johnson Space Center

  4. Software tools for microprocessor based systems

    International Nuclear Information System (INIS)

    Halatsis, C.

    1981-01-01

    After a short review of the hardware and/or software tools for the development of single-chip, fixed instruction set microprocessor-based sytems we focus on the software tools for designing systems based on microprogrammed bit-sliced microprocessors. Emphasis is placed on meta-microassemblers and simulation facilties at the register-transfer-level and architecture level. We review available meta-microassemblers giving their most important features, advantages and disadvantages. We also make extentions to higher-level microprogramming languages and associated systems specifically developed for bit-slices. In the area of simulation facilities we first discuss the simulation objectives and the criteria for chosing the right simulation language. We consertrate to simulation facilities already used in bit-slices projects and discuss the gained experience. We conclude by describing the way the Signetics meta-microassembler and the ISPS simulation tool have been employed in the design of a fast microprogrammed machine, called MICE, made out of ECL bit-slices. (orig.)

  5. Software Simulates Sight: Flat Panel Mura Detection

    Science.gov (United States)

    2008-01-01

    In the increasingly sophisticated world of high-definition flat screen monitors and television screens, image clarity and the elimination of distortion are paramount concerns. As the devices that reproduce images become more and more sophisticated, so do the technologies that verify their accuracy. By simulating the manner in which a human eye perceives and interprets a visual stimulus, NASA scientists have found ways to automatically and accurately test new monitors and displays. The Spatial Standard Observer (SSO) software metric, developed by Dr. Andrew B. Watson at Ames Research Center, measures visibility and defects in screens, displays, and interfaces. In the design of such a software tool, a central challenge is determining which aspects of visual function to include while accuracy and generality are important, relative simplicity of the software module is also a key virtue. Based on data collected in ModelFest, a large cooperative multi-lab project hosted by the Optical Society of America, the SSO simulates a simplified model of human spatial vision, operating on a pair of images that are viewed at a specific viewing distance with pixels having a known relation to luminance. The SSO measures the visibility of foveal spatial patterns, or the discriminability of two patterns, by incorporating only a few essential components of vision. These components include local contrast transformation, a contrast sensitivity function, local masking, and local pooling. By this construction, the SSO provides output in units of "just noticeable differences" (JND) a unit of measure based on the assumed smallest difference of sensory input detectable by a human being. Herein is the truly amazing ability of the SSO, while conventional methods can manipulate images, the SSO models human perception. This set of equations actually defines a mathematical way of working with an image that accurately reflects the way in which the human eye and mind behold a stimulus. The SSO is

  6. Use of Human Modeling Simulation Software in the Task Analysis of the Environmental Control and Life Support System Component Installation Procedures

    Science.gov (United States)

    Estes, Samantha; Parker, Nelson C. (Technical Monitor)

    2001-01-01

    Virtual reality and simulation applications are becoming widespread in human task analysis. These programs have many benefits for the Human Factors Engineering field. Not only do creating and using virtual environments for human engineering analyses save money and time, this approach also promotes user experimentation and provides increased quality of analyses. This paper explains the human engineering task analysis performed on the Environmental Control and Life Support System (ECLSS) space station rack and its Distillation Assembly (DA) subsystem using EAI's human modeling simulation software, Jack. When installed on the International Space Station (ISS), ECLSS will provide the life and environment support needed to adequately sustain crew life. The DA is an Orbital Replaceable Unit (ORU) that provides means of wastewater (primarily urine from flight crew and experimental animals) reclamation. Jack was used to create a model of the weightless environment of the ISS Node 3, where the ECLSS is housed. Computer aided drawings of the ECLSS rack and DA system were also brought into the environment. Anthropometric models of a 95th percentile male and 5th percentile female were used to examine the human interfaces encountered during various ECLSS and DA tasks. The results of the task analyses were used in suggesting modifications to hardware and crew task procedures to improve accessibility, conserve crew time, and add convenience for the crew. This paper will address some of those suggested modifications and the method of presenting final analyses for requirements verification.

  7. Survey on Projects at DLR Simulation and Software Technology with Focus on Software Engineering and HPC

    OpenAIRE

    Schreiber, Andreas; Basermann, Achim

    2013-01-01

    We introduce the DLR institute “Simulation and Software Technology” (SC) and present current activities regarding software engineering and high performance computing (HPC) in German or international projects. Software engineering at SC focusses on data and knowledge management as well as tools for studies and experiments. We discuss how we apply software configuration management, validation and verification in our projects. Concrete research topics are traceability of (software devel...

  8. Modeling of Some Chaotic Systems with AnyLogic Software

    Directory of Open Access Journals (Sweden)

    Biljana Zlatanovska

    2018-05-01

    Full Text Available The chaotic systems are already known in the theory of chaos. In our paper will be analyzed the following chaotic systems: Rossler, Chua and Chen systems. All of them are systems of ordinary differential equations. By mathematical software Mathematica and MatLab, their graphical representation as continuous dynamical systems is already known. By computer simulations, via examples, the systems will be analyzed using AnyLogic software. We would like to present the way how ordinary differential equations are modeling with AnyLogic software, as one of the simplest software for use.

  9. Investigations on development of software and hardware for nuclear power plant training simulators

    International Nuclear Information System (INIS)

    He Sian.

    1987-01-01

    The requirements of a training simulator are discussed. The algorithms of the lumped and distributed parameter system and real time system are analysed on principle in software design. The assumed schemes of a hardware system are proposed, too

  10. High Confidence Software and Systems Research Needs

    Data.gov (United States)

    Networking and Information Technology Research and Development, Executive Office of the President — This White Paper presents a survey of high confidence software and systems research needs. It has been prepared by the High Confidence Software and Systems...

  11. Avionics Simulation, Development and Software Engineering

    Science.gov (United States)

    2002-01-01

    During this reporting period, all technical responsibilities were accomplished as planned. A close working relationship was maintained with personnel of the MSFC Avionics Department Software Group (ED14), the MSFC EXPRESS Project Office (FD31), and the Huntsville Boeing Company. Accomplishments included: performing special tasks; supporting Software Review Board (SRB), Avionics Test Bed (ATB), and EXPRESS Software Control Panel (ESCP) activities; participating in technical meetings; and coordinating issues between the Boeing Company and the MSFC Project Office.

  12. SSAGES: Software Suite for Advanced General Ensemble Simulations

    Science.gov (United States)

    Sidky, Hythem; Colón, Yamil J.; Helfferich, Julian; Sikora, Benjamin J.; Bezik, Cody; Chu, Weiwei; Giberti, Federico; Guo, Ashley Z.; Jiang, Xikai; Lequieu, Joshua; Li, Jiyuan; Moller, Joshua; Quevillon, Michael J.; Rahimi, Mohammad; Ramezani-Dakhel, Hadi; Rathee, Vikramjit S.; Reid, Daniel R.; Sevgen, Emre; Thapar, Vikram; Webb, Michael A.; Whitmer, Jonathan K.; de Pablo, Juan J.

    2018-01-01

    Molecular simulation has emerged as an essential tool for modern-day research, but obtaining proper results and making reliable conclusions from simulations requires adequate sampling of the system under consideration. To this end, a variety of methods exist in the literature that can enhance sampling considerably, and increasingly sophisticated, effective algorithms continue to be developed at a rapid pace. Implementation of these techniques, however, can be challenging for experts and non-experts alike. There is a clear need for software that provides rapid, reliable, and easy access to a wide range of advanced sampling methods and that facilitates implementation of new techniques as they emerge. Here we present SSAGES, a publicly available Software Suite for Advanced General Ensemble Simulations designed to interface with multiple widely used molecular dynamics simulations packages. SSAGES allows facile application of a variety of enhanced sampling techniques—including adaptive biasing force, string methods, and forward flux sampling—that extract meaningful free energy and transition path data from all-atom and coarse-grained simulations. A noteworthy feature of SSAGES is a user-friendly framework that facilitates further development and implementation of new methods and collective variables. In this work, the use of SSAGES is illustrated in the context of simple representative applications involving distinct methods and different collective variables that are available in the current release of the suite. The code may be found at: https://github.com/MICCoM/SSAGES-public.

  13. SSAGES: Software Suite for Advanced General Ensemble Simulations

    Energy Technology Data Exchange (ETDEWEB)

    Sidky, Hythem [Department of Chemical and Biomolecular Engineering, University of Notre Dame, Notre Dame, Indiana 46556, USA; Colón, Yamil J. [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Institute for Molecular Engineering and Materials Science Division, Argonne National Laboratory, Lemont, Illinois 60439, USA; Helfferich, Julian [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Steinbuch Center for Computing, Karlsruhe Institute of Technology, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen, Germany; Sikora, Benjamin J. [Department of Chemical and Biomolecular Engineering, University of Notre Dame, Notre Dame, Indiana 46556, USA; Bezik, Cody [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Chu, Weiwei [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Giberti, Federico [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Guo, Ashley Z. [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Jiang, Xikai [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Lequieu, Joshua [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Li, Jiyuan [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Moller, Joshua [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Quevillon, Michael J. [Department of Chemical and Biomolecular Engineering, University of Notre Dame, Notre Dame, Indiana 46556, USA; Rahimi, Mohammad [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Ramezani-Dakhel, Hadi [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Department of Biochemistry and Molecular Biology, University of Chicago, Chicago, Illinois 60637, USA; Rathee, Vikramjit S. [Department of Chemical and Biomolecular Engineering, University of Notre Dame, Notre Dame, Indiana 46556, USA; Reid, Daniel R. [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Sevgen, Emre [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Thapar, Vikram [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Webb, Michael A. [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Institute for Molecular Engineering and Materials Science Division, Argonne National Laboratory, Lemont, Illinois 60439, USA; Whitmer, Jonathan K. [Department of Chemical and Biomolecular Engineering, University of Notre Dame, Notre Dame, Indiana 46556, USA; de Pablo, Juan J. [Institute for Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA; Institute for Molecular Engineering and Materials Science Division, Argonne National Laboratory, Lemont, Illinois 60439, USA

    2018-01-28

    Molecular simulation has emerged as an essential tool for modern-day research, but obtaining proper results and making reliable conclusions from simulations requires adequate sampling of the system under consideration. To this end, a variety of methods exist in the literature that can enhance sampling considerably, and increasingly sophisticated, effective algorithms continue to be developed at a rapid pace. Implementation of these techniques, however, can be challenging for experts and non-experts alike. There is a clear need for software that provides rapid, reliable, and easy access to a wide range of advanced sampling methods, and that facilitates implementation of new techniques as they emerge. Here we present SSAGES, a publicly available Software Suite for Advanced General Ensemble Simulations designed to interface with multiple widely used molecular dynamics simulations packages. SSAGES allows facile application of a variety of enhanced sampling techniques—including adaptive biasing force, string methods, and forward flux sampling—that extract meaningful free energy and transition path data from all-atom and coarse grained simulations. A noteworthy feature of SSAGES is a user-friendly framework that facilitates further development and implementation of new methods and collective variables. In this work, the use of SSAGES is illustrated in the context of simple representative applications involving distinct methods and different collective variables that are available in the current release of the suite.

  14. MEGACELL: A nanocrystal model construction software for HRTEM multislice simulation

    International Nuclear Information System (INIS)

    Stroppa, Daniel G.; Righetto, Ricardo D.; Montoro, Luciano A.; Ramirez, Antonio J.

    2011-01-01

    Image simulation has an invaluable importance for the accurate analysis of High Resolution Transmission Electron Microscope (HRTEM) results, especially due to its non-linear image formation mechanism. Because the as-obtained images cannot be interpreted in a straightforward fashion, the retrieval of both qualitative and quantitative information from HRTEM micrographs requires an iterative process including the simulation of a nanocrystal model and its comparison with experimental images. However most of the available image simulation software requires atom-by-atom coordinates as input for the calculations, which can be prohibitive for large finite crystals and/or low-symmetry systems and zone axis orientations. This paper presents an open source citation-ware tool named MEGACELL, which was developed to assist on the construction of nanocrystals models. It allows the user to build nanocrystals with virtually any convex polyhedral geometry and to retrieve its atomic positions either as a plain text file or as an output compatible with EMS (Electron Microscopy Software) input protocol. In addition to the description of this tool features, some construction examples and its application for scientific studies are presented. These studies show MEGACELL as a handy tool, which allows an easier construction of complex nanocrystal models and improves the quantitative information extraction from HRTEM images. -- Highlights: → A software to support the HRTEM image simulation of nanocrystals in actual size. → MEGACELL allows the construction of complex nanocrystals models for multislice image simulation. → Some examples of improved nanocrystalline system characterization are presented, including the analysis of 3D morphology and growth behavior.

  15. Space Flight Software Development Software for Intelligent System Health Management

    Science.gov (United States)

    Trevino, Luis C.; Crumbley, Tim

    2004-01-01

    The slide presentation examines the Marshall Space Flight Center Flight Software Branch, including software development projects, mission critical space flight software development, software technical insight, advanced software development technologies, and continuous improvement in the software development processes and methods.

  16. Summary of the International Conference on Software and System Processes

    DEFF Research Database (Denmark)

    Kuhrmann, Marco; O'Connor, Rory V.; Perry, Dewayne E.

    2016-01-01

    The International Conference on Software and Systems Process (ICSSP), continuing the success of Software Process Workshop (SPW), the Software Process Modeling and Simulation Workshop (ProSim) and the International Conference on Software Process (ICSP) conference series, has become the established...... premier event in the field of software and systems engineering processes. It provides a leading forum for the exchange of research outcomes and industrial best-practices in process development from software and systems disciplines. ICSSP 2016 was held in Austin, Texas, from 14-15 May 2016, co......-located with the 38th International Conference on Software Engineering (ICSE). The theme of mICSSP 2016 was studying "Process(es) in Action" by recognizing that the AS-Planned and AS-Practiced processes can be quite different in many ways including their ows, their complexity and the evolving needs of stakeholders...

  17. FPGA-accelerated simulation of computer systems

    CERN Document Server

    Angepat, Hari; Chung, Eric S; Hoe, James C; Chung, Eric S

    2014-01-01

    To date, the most common form of simulators of computer systems are software-based running on standard computers. One promising approach to improve simulation performance is to apply hardware, specifically reconfigurable hardware in the form of field programmable gate arrays (FPGAs). This manuscript describes various approaches of using FPGAs to accelerate software-implemented simulation of computer systems and selected simulators that incorporate those techniques. More precisely, we describe a simulation architecture taxonomy that incorporates a simulation architecture specifically designed f

  18. Software And Systems Engineering Risk Management

    Science.gov (United States)

    2010-04-01

    RSKM 2004 COSO Enterprise RSKM Framework 2006 ISO/IEC 16085 Risk Management Process 2008 ISO/IEC 12207 Software Lifecycle Processes 2009 ISO/IEC...1 Software And Systems Engineering Risk Management John Walz VP Technical and Conferences Activities, IEEE Computer Society Vice-Chair Planning...Software & Systems Engineering Standards Committee, IEEE Computer Society US TAG to ISO TMB Risk Management Working Group Systems and Software

  19. Software Quality Assurance for Nuclear Safety Systems

    International Nuclear Information System (INIS)

    Sparkman, D R; Lagdon, R

    2004-01-01

    The US Department of Energy has undertaken an initiative to improve the quality of software used to design and operate their nuclear facilities across the United States. One aspect of this initiative is to revise or create new directives and guides associated with quality practices for the safety software in its nuclear facilities. Safety software includes the safety structures, systems, and components software and firmware, support software and design and analysis software used to ensure the safety of the facility. DOE nuclear facilities are unique when compared to commercial nuclear or other industrial activities in terms of the types and quantities of hazards that must be controlled to protect workers, public and the environment. Because of these differences, DOE must develop an approach to software quality assurance that ensures appropriate risk mitigation by developing a framework of requirements that accomplishes the following goals: (sm b ullet) Ensures the software processes developed to address nuclear safety in design, operation, construction and maintenance of its facilities are safe (sm b ullet) Considers the larger system that uses the software and its impacts (sm b ullet) Ensures that the software failures do not create unsafe conditions Software designers for nuclear systems and processes must reduce risks in software applications by incorporating processes that recognize, detect, and mitigate software failure in safety related systems. It must also ensure that fail safe modes and component testing are incorporated into software design. For nuclear facilities, the consideration of risk is not necessarily sufficient to ensure safety. Systematic evaluation, independent verification and system safety analysis must be considered for software design, implementation, and operation. The software industry primarily uses risk analysis to determine the appropriate level of rigor applied to software practices. This risk-based approach distinguishes safety

  20. gemcWeb: A Cloud Based Nuclear Physics Simulation Software

    Science.gov (United States)

    Markelon, Sam

    2017-09-01

    gemcWeb allows users to run nuclear physics simulations from the web. Being completely device agnostic, scientists can run simulations from anywhere with an Internet connection. Having a full user system, gemcWeb allows users to revisit and revise their projects, and share configurations and results with collaborators. gemcWeb is based on simulation software gemc, which is based on standard GEant4. gemcWeb requires no C++, gemc, or GEant4 knowledge. Using a simple but powerful GUI allows users to configure their project from geometries and configurations stored on the deployment server. Simulations are then run on the server, with results being posted to the user, and then securely stored. Python based and open-source, the main version of gemcWeb is hosted internally at Jefferson National Labratory and used by the CLAS12 and Electron-Ion Collider Project groups. However, as the software is open-source, and hosted as a GitHub repository, an instance can be deployed on the open web, or any institution's intra-net. An instance can be configured to host experiments specific to an institution, and the code base can be modified by any individual or group. Special thanks to: Maurizio Ungaro, PhD., creator of gemc; Markus Diefenthaler, PhD., advisor; and Kyungseon Joo, PhD., advisor.

  1. Software for simulation of a computed tomography imaging spectrometer using optical design software

    Science.gov (United States)

    Spuhler, Peter T.; Willer, Mark R.; Volin, Curtis E.; Descour, Michael R.; Dereniak, Eustace L.

    2000-11-01

    Our Imaging Spectrometer Simulation Software known under the name Eikon should improve and speed up the design of a Computed Tomography Imaging Spectrometer (CTIS). Eikon uses existing raytracing software to simulate a virtual instrument. Eikon enables designers to virtually run through the design, calibration and data acquisition, saving significant cost and time when designing an instrument. We anticipate that Eikon simulations will improve future designs of CTIS by allowing engineers to explore more instrument options.

  2. Software development for a switch-based data acquisition system

    Energy Technology Data Exchange (ETDEWEB)

    Booth, A. (Superconducting Super Collider Lab., Dallas, TX (United States)); Black, D.; Walsh, D. (Fermi National Accelerator Lab., Batavia, IL (United States))

    1991-12-01

    We report on the software aspects of the development of a switch-based data acquisition system at Fermilab. This paper describes how, with the goal of providing an integrated systems engineering'' environment, several powerful software tools were put in place to facilitate extensive exploration of all aspects of the design. These tools include a simulation package, graphics package and an Expert System shell which have been integrated to provide an environment which encourages the close interaction of hardware and software engineers. This paper includes a description of the simulation, user interface, embedded software, remote procedure calls, and diagnostic software which together have enabled us to provide real-time control and monitoring of a working prototype switch-based data acquisition (DAQ) system.

  3. Dedicated software for diffractive optics design and simulation

    International Nuclear Information System (INIS)

    Firsov, A; Brzhezinskaya, M; Erko, A; Firsov, A; Svintsov, A

    2013-01-01

    An efficient software package for the structure design and simulation of imaging properties of diffraction optical elements has been developed. It operates with point source and consists of: the ZON software, to calculate the structure of an optical element in transmission and reflection; the KRGF software, to simulate the diffraction properties of an ideal optical element with point source; the DS software, to calculate the diffraction properties by taking into consideration material and shadowing effects. Optional software allows simulation with a real non-point source. Zone plate thickness profile, source shape as well as substrate curvature are considered in this calculation. This is especially important for the diffractive focusing elements and gratings at a total external reflection, given that the lateral size of the structure can be up to 1 m. The program package can be used in combination with the Nanomaker software to prepare data for ion and e-beam surface modifications and corrections.

  4. Software tool for horizontal-axis wind turbine simulation

    Energy Technology Data Exchange (ETDEWEB)

    Vitale, A.J. [Instituto Argentino de Oceanografia, Camino La Carrindanga Km. 7, 5 CC 804, B8000FWB Bahia Blanca (Argentina); Universidad Tecnologica Nacional Facultad Regional Bahia Blanca, GESE, 11 de Abril 461, B8000LMI Bahia Blanca (Argentina); Dpto. de Ing. Electrica y de Computadoras, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina); Rossi, A.P. [Universidad Tecnologica Nacional Facultad Regional Bahia Blanca, GESE, 11 de Abril 461, B8000LMI Bahia Blanca (Argentina); Dpto. de Ing. Electrica y de Computadoras, Universidad Nacional del Sur, Av. Alem 1253, 8000 Bahia Blanca (Argentina)

    2008-07-15

    The main problem of a wind turbine generator design project is the design of the right blades capable of satisfying the specific energy requirement of an electric system with optimum performance. Once the blade has been designed for optimum operation at a particular rotor angular speed, it is necessary to determine the overall performance of the rotor under the range of wind speed that it will encounter. A software tool that simulates low-power, horizontal-axis wind turbines was developed for this purpose. With this program, the user can calculate the rotor power output for any combination of wind and rotor speeds, with definite blade shape and airfoil characteristics. The software also provides information about distribution of forces along the blade span, for different operational conditions. (author)

  5. SimulaQron - A simulator for developing quantum internet software

    OpenAIRE

    Dahlberg, Axel; Wehner, Stephanie

    2017-01-01

    We introduce a simulator for a quantum internet with the specific goal to support software development. A quantum internet consists of local quantum processors, which are interconnected by quantum communication channels that enable the transmission of qubits between the different processors. While many simulators exist for local quantum processors, there is presently no simulator for a quantum internet tailored towards software development. Quantum internet protocols require both classical as...

  6. Software for nuclear data acquisition systems

    International Nuclear Information System (INIS)

    Christensen, P.

    1983-01-01

    The situation for experimenters and system designers needing software for instrumentation is described. It is stated that software for a data acquisition system can be divided into programmes described as the foundation software, the applications programme, and the analysis programme. Special attention is given to CAMAC. Two examples from Risoe describing data transportation and archiving are given. Finally the supply of software and the problems of documentation are described. (author)

  7. Cronos 2: a neutronic simulation software for reactor core calculations

    International Nuclear Information System (INIS)

    Lautard, J.J.; Magnaud, C.; Moreau, F.; Baudron, A.M.

    1999-01-01

    The CRONOS2 software is that part of the SAPHYR code system dedicated to neutronic core calculations. CRONOS2 is a powerful tool for reactor design, fuel management and safety studies. Its modular structure and great flexibility make CRONOS2 an unique simulation tool for research and development for a wide variety of reactor systems. CRONOS2 is a versatile tool that covers a large range of applications from very fast calculations used in training simulators to time and memory consuming reference calculations needed to understand complex physical phenomena. CRONOS2 has a procedure library named CPROC that allows the user to create its own application environment fitted to a specific industrial use. (authors)

  8. Management information systems software evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Al-Tunisi, N.; Ghazzawi, A.; Gruyaert, F.; Clarke, D. [Saudi Aramco, Dhahran (Saudi Arabia). Process and Control Systems Dept.

    1995-11-01

    In November 1993, Saudi Aramco management endorsed a proposal to coordinate the development of the Management Information Systems (MISs) of four concurrent projects for its facilities Controls Modernization Program. The affected projects were the Ras Tanura Refinery Upgrade Project, the Abqaiq Plant Controls Modernization and the Shedgum and Uthmaniyah Gas plants Control Upgrade Projects. All of these projects had a significant requirement of MISs in their scope. Under the leadership of the Process and Control Systems Department, and MIS Coordination Team was formed with representatives of several departments. An MIS Applications Evaluation procedure was developed based on the Kepner Tregoe Decisions Analysis Process and general questionnaires were sent to over a hundred potential Vendors. The applications were divided into several categories, such as: Data Capture and Historization, Human User Interface, Trending, Reporting, Graphic Displays, Data Reconciliation, Statistical Analysis, Expert Systems, Maintenance Applications, Document Management and Operations Planning and Scheduling. For each of the MIS Application areas, detailed follow-up questionnaires were used to short list the candidate products. In May and June 1994, selected Vendors were invited to Saudi Arabia for an Exhibition which was open to all Saudi Aramco employees. In conjunction with this, the Vendors were subjected to a rigorous product testing exercise by independent teams of testers. The paper will describe the methods used and the lessons learned in this extensive software evaluation phase, which was a first for Saudi Aramco.

  9. Management information systems software evaluation

    International Nuclear Information System (INIS)

    Al-Tunisi, N.; Ghazzawi, A.; Gruyaert, F.; Clarke, D.

    1995-01-01

    In November 1993, Saudi Aramco management endorsed a proposal to coordinate the development of the Management Information Systems (MISs) of four concurrent projects for its facilities Controls Modernization Program. The affected projects were the Ras Tanura Refinery Upgrade Project, the Abqaiq Plant Controls Modernization and the Shedgum and Uthmaniyah Gas plants Control Upgrade Projects. All of these projects had a significant requirement of MISs in their scope. Under the leadership of the Process and Control Systems Department, and MIS Coordination Team was formed with representatives of several departments. An MIS Applications Evaluation procedure was developed based on the Kepner Tregoe Decisions Analysis Process and general questionnaires were sent to over a hundred potential Vendors. The applications were divided into several categories, such as: Data Capture and Historization, Human User Interface, Trending, Reporting, Graphic Displays, Data Reconciliation, Statistical Analysis, Expert Systems, Maintenance Applications, Document Management and Operations Planning and Scheduling. For each of the MIS Application areas, detailed follow-up questionnaires were used to short list the candidate products. In May and June 1994, selected Vendors were invited to Saudi Arabia for an Exhibition which was open to all Saudi Aramco employees. In conjunction with this, the Vendors were subjected to a rigorous product testing exercise by independent teams of testers. The paper will describe the methods used and the lessons learned in this extensive software evaluation phase, which was a first for Saudi Aramco

  10. Test software for BESIII MDC electronics system

    International Nuclear Information System (INIS)

    Zhang Hongyu; Sheng Huayi; Zhu Haitao; Ji Xiaolu; Zhao Dongxu

    2006-01-01

    This paper presents the design of Test System Software for BESIII MDC Electronics. Two kinds of test systems, SBS VP7 based and PowerPC based systems, and their corresponding test software are introduced. The software is developed in LabVIEW 7.1 and Microsoft Visual C++ 6.0, some test functions of the software, as well as their user interfaces, are described in detail. The software has been applied in hardware debugging, performance test and long term stability test. (authors)

  11. Software dependability in the Tandem GUARDIAN system

    Science.gov (United States)

    Lee, Inhwan; Iyer, Ravishankar K.

    1995-01-01

    Based on extensive field failure data for Tandem's GUARDIAN operating system this paper discusses evaluation of the dependability of operational software. Software faults considered are major defects that result in processor failures and invoke backup processes to take over. The paper categorizes the underlying causes of software failures and evaluates the effectiveness of the process pair technique in tolerating software faults. A model to describe the impact of software faults on the reliability of an overall system is proposed. The model is used to evaluate the significance of key factors that determine software dependability and to identify areas for improvement. An analysis of the data shows that about 77% of processor failures that are initially considered due to software are confirmed as software problems. The analysis shows that the use of process pairs to provide checkpointing and restart (originally intended for tolerating hardware faults) allows the system to tolerate about 75% of reported software faults that result in processor failures. The loose coupling between processors, which results in the backup execution (the processor state and the sequence of events) being different from the original execution, is a major reason for the measured software fault tolerance. Over two-thirds (72%) of measured software failures are recurrences of previously reported faults. Modeling, based on the data, shows that, in addition to reducing the number of software faults, software dependability can be enhanced by reducing the recurrence rate.

  12. GROMOS++Software for the Analysis of Biomolecular Simulation Trajectories

    NARCIS (Netherlands)

    Eichenberger, A.P.; Allison, J.R.; Dolenc, J.; Geerke, D.P.; Horta, B.A.C.; Meier, K; Oostenbrink, B.C.; Schmid, N.; Steiner, D; Wang, D.; van Gunsteren, W.F.

    2011-01-01

    GROMOS++ is a set of C++ programs for pre- and postprocessing of molecular dynamics simulation trajectories and as such is part of the GROningen MOlecular Simulation software for (bio)molecular simulation. It contains more than 70 programs that can be used to prepare data for the production of

  13. Honeywell Modular Automation System Computer Software Documentation

    International Nuclear Information System (INIS)

    STUBBS, A.M.

    2000-01-01

    The purpose of this Computer Software Document (CSWD) is to provide configuration control of the Honeywell Modular Automation System (MAS) in use at the Plutonium Finishing Plant (PFP). This CSWD describes hardware and PFP developed software for control of stabilization furnaces. The Honeywell software can generate configuration reports for the developed control software. These reports are described in the following section and are attached as addendum's. This plan applies to PFP Engineering Manager, Thermal Stabilization Cognizant Engineers, and the Shift Technical Advisors responsible for the Honeywell MAS software/hardware and administration of the Honeywell System

  14. The Particle-in-Cell and Kinetic Simulation Software Center

    Science.gov (United States)

    Mori, W. B.; Decyk, V. K.; Tableman, A.; Fonseca, R. A.; Tsung, F. S.; Hu, Q.; Winjum, B. J.; An, W.; Dalichaouch, T. N.; Davidson, A.; Hildebrand, L.; Joglekar, A.; May, J.; Miller, K.; Touati, M.; Xu, X. L.

    2017-10-01

    The UCLA Particle-in-Cell and Kinetic Simulation Software Center (PICKSC) aims to support an international community of PIC and plasma kinetic software developers, users, and educators; to increase the use of this software for accelerating the rate of scientific discovery; and to be a repository of knowledge and history for PIC. We discuss progress towards making available and documenting illustrative open-source software programs and distinct production programs; developing and comparing different PIC algorithms; coordinating the development of resources for the educational use of kinetic software; and the outcomes of our first sponsored OSIRIS users workshop. We also welcome input and discussion from anyone interested in using or developing kinetic software, in obtaining access to our codes, in collaborating, in sharing their own software, or in commenting on how PICKSC can better serve the DPP community. Supported by NSF under Grant ACI-1339893 and by the UCLA Institute for Digital Research and Education.

  15. The portability of the "Electronics Workbench" simulation software to China

    NARCIS (Netherlands)

    Collis, Betty; Zhi-Cheng, Dong

    1993-01-01

    This article discusses the portability of the Canadian-made simulation software package, "Electronic Workbench" package (EWB) to China. As part of a larger project investigating the portability of various educational software packages, the EWB package was used in electronics instruction in China and

  16. Porting a Java-based Brain Simulation Software to C++

    CERN Multimedia

    CERN. Geneva

    2015-01-01

    A currently available software solution to simulate neural development is Cx3D. However, this software is Java-based, and not ideal for high performance computing. This talk presents our step-by-step porting approach, that uses SWIG as a tool to interface C++ code from Java.

  17. Evolving a Simulation Model Product Line Software Architecture from Heterogeneous Model Representations

    National Research Council Canada - National Science Library

    Greaney, Kevin

    2003-01-01

    .... Many of these large-scale, software-intensive simulation systems were autonomously developed over time, and subject to varying degrees of funding, maintenance, and life-cycle management practices...

  18. Hard- and software of real time simulation tools of Electric Power System for adequate modeling power semiconductors in voltage source convertor based HVDC and FACTS

    Directory of Open Access Journals (Sweden)

    Ufa Ruslan A.

    2014-01-01

    Full Text Available The motivation of the presented research is based on the needs for development of new methods and tools for adequate simulation of Flexible Alternating Current Transmission System (FACTS devices and High Voltage Direct Current Transmission (HVDC system as part of real electric power systems (EPS. For that, a hybrid approach for advanced simulation of the FACTS and HVDC based on Voltage Source is proposed. The presented simulation results of the developed hybrid model of VSC confirm the achievement of the desired properties of the model and the effectiveness of the proposed solutions.

  19. Simulation of Phase Meter Using TINA Software

    African Journals Online (AJOL)

    AJC

    analysis. Transient analysis calculates the circuit response to various input waveforms. Results ... with key components IC AD633 and OPAMP. .... Circuit simulation has become a core technology in the field of modern electronics engineering,.

  20. Empirical Validation of Building Simulation Software

    DEFF Research Database (Denmark)

    Kalyanova, Olena; Heiselberg, Per

    The work described in this report is the result of a collaborative effort of members of the International Energy Agency (IEA), Task 34/43: Testing and validation of building energy simulation tools experts group.......The work described in this report is the result of a collaborative effort of members of the International Energy Agency (IEA), Task 34/43: Testing and validation of building energy simulation tools experts group....

  1. A Software Development Platform for Mechatronic Systems

    DEFF Research Database (Denmark)

    Guan, Wei

    Software has become increasingly determinative for development of mechatronic systems, which underscores the importance of demands for shortened time-to-market, increased productivity, higher quality, and improved dependability. As the complexity of systems is dramatically increasing, these demands...... present a challenge to the practitioners who adopt conventional software development approach. An effective approach towards industrial production of software for mechatronic systems is needed. This approach requires a disciplined engineering process that encompasses model-driven engineering and component......-based software engineering, whereby we enable incremental software development using component models to address the essential design issues of real-time embedded systems. To this end, this dissertation presents a software development platform that provides an incremental model-driven development process based...

  2. Healthcare system simulation using Witness

    International Nuclear Information System (INIS)

    Khakdaman, Masoud; Zeinahvazi, Milad; Zohoori, Bahareh; Nasiri, Fardokht; Wong, Kuan Yew

    2013-01-01

    Simulation techniques have a proven track record in manufacturing industry as well as other areas such as healthcare system improvement. In this study, simulation model of a health center in Malaysia is developed through the application of WITNESS simulation software which has shown its flexibility and capability in manufacturing industry. Modelling procedure is started through process mapping and data collection and continued with model development, verification, validation and experimentation. At the end, final results and possible future improvements are demonstrated.

  3. Model-driven design of simulation support for the TERRA robot software tool suite

    NARCIS (Netherlands)

    Lu, Zhou; Bezemer, M.M.; Broenink, Johannes F.

    2015-01-01

    Model-Driven Development (MDD) – based on the concepts of model, meta-model and model transformation – is an approach to develop predictable and re- liable software for Cyber-Physical Systems (CPS). The work presented here concerns a methodology to design simulation software based on MDD techniques,

  4. A NEW EXHAUST VENTILATION SYSTEM DESIGN SOFTWARE

    Directory of Open Access Journals (Sweden)

    H. Asilian Mahabady

    2007-09-01

    Full Text Available A Microsoft Windows based ventilation software package is developed to reduce time-consuming and boring procedure of exhaust ventilation system design. This program Assure accurate and reliable air pollution control related calculations. Herein, package is tentatively named Exhaust Ventilation Design Software which is developed in VB6 programming environment. Most important features of Exhaust Ventilation Design Software that are ignored in formerly developed packages are Collector design and fan dimension data calculations. Automatic system balance is another feature of this package. Exhaust Ventilation Design Software algorithm for design is based on two methods: Balance by design (Static pressure balance and design by Blast gate. The most important section of software is a spreadsheet that is designed based on American Conference of Governmental Industrial Hygienists calculation sheets. Exhaust Ventilation Design Software is developed so that engineers familiar with American Conference of Governmental Industrial Hygienists datasheet can easily employ it for ventilation systems design. Other sections include Collector design section (settling chamber, cyclone, and packed tower, fan geometry and dimension data section, a unit converter section (that helps engineers to deal with units, a hood design section and a Persian HTML help. Psychometric correction is also considered in Exhaust Ventilation Design Software. In Exhaust Ventilation Design Software design process, efforts are focused on improving GUI (graphical user interface and use of programming standards in software design. Reliability of software has been evaluated and results show acceptable accuracy.

  5. A Reusable Software Architecture for Small Satellite AOCS Systems

    DEFF Research Database (Denmark)

    Alminde, Lars; Bendtsen, Jan Dimon; Laursen, Karl Kaas

    2006-01-01

    This paper concerns the software architecture called Sophy, which is an abbreviation for Simulation, Observation, and Planning in HYbrid systems. We present a framework that allows execution of hybrid dynamical systems in an on-line distributed computing environment, which includes interaction...... with both hardware and on-board software. Some of the key issues addressed by the framework are automatic translation of mathematical specifications of hybrid systems into executable software entities, management of execution of coupled models in a parallel distributed environment, as well as interaction...... with external components, hardware and/or software, through generic interfaces. Sophy is primarily intended as a tool for development of model based reusable software for the control and autonomous functions of satellites and/or satellite clusters....

  6. Software for Embedded Control Systems

    NARCIS (Netherlands)

    Broenink, Johannes F.; Hilderink, G.H.; Jovanovic, D.S.

    2001-01-01

    The research of our team deals with the realization of control schemes on digital computers. As such the emphasis is on embedded control software implementation. Applications are in the field of mechatronic devices, using a mechatronic design approach (the integrated and optimal design of a

  7. Development of Radio Frequency Antenna Radiation Simulation Software

    International Nuclear Information System (INIS)

    Mohamad Idris Taib; Rozaimah Abd Rahim; Noor Ezati Shuib; Wan Saffiey Wan Abdullah

    2014-01-01

    Antennas are widely used national wide for radio frequency propagation especially for communication system. Radio frequency is electromagnetic spectrum from 10 kHz to 300 GHz and non-ionizing. These radiation exposures to human being have radiation hazard risk. This software was under development using LabVIEW for radio frequency exposure calculation. For the first phase of this development, software purposely to calculate possible maximum exposure for quick base station assessment, using prediction methods. This software also can be used for educational purpose. Some results of this software are comparing with commercial IXUS and free ware NEC software. (author)

  8. Experiences on dynamic simulation software in chemical engineering education

    DEFF Research Database (Denmark)

    Komulainen, Tiina M.; Enemark-rasmussen, Rasmus; Sin, Gürkan

    2012-01-01

    Commercial process simulators are increasing interest in the chemical engineer education. In this paper, the use of commercial dynamic simulation software, D-SPICE® and K-Spice®, for three different chemical engineering courses is described and discussed. The courses cover the following topics...

  9. PROCESS SIMULATION IN SUPPLY CHAIN USING LOGWARE SOFTWARE

    OpenAIRE

    Sebastian Kot; Beata Åšlusarczyk

    2009-01-01

    The authors present basis of simulation usage in managerial decisionsupport focusing on the supply chain processes. In the beginning the need for simulationis presented, then advantages and disadvantages of simulation experiments and thesimulation tools juxtaposition. Finally the chances of supply chain process simulationusing Logware software are presented.

  10. A Simulation Model for the Waterfall Software Development Life Cycle

    OpenAIRE

    Bassil, Youssef

    2012-01-01

    Software development life cycle or SDLC for short is a methodology for designing, building, and maintaining information and industrial systems. So far, there exist many SDLC models, one of which is the Waterfall model which comprises five phases to be completed sequentially in order to develop a software solution. However, SDLC of software systems has always encountered problems and limitations that resulted in significant budget overruns, late or suspended deliveries, and dissatisfied client...

  11. Tools for Embedded Computing Systems Software

    Science.gov (United States)

    1978-01-01

    A workshop was held to assess the state of tools for embedded systems software and to determine directions for tool development. A synopsis of the talk and the key figures of each workshop presentation, together with chairmen summaries, are presented. The presentations covered four major areas: (1) tools and the software environment (development and testing); (2) tools and software requirements, design, and specification; (3) tools and language processors; and (4) tools and verification and validation (analysis and testing). The utility and contribution of existing tools and research results for the development and testing of embedded computing systems software are described and assessed.

  12. Expert System Software Assistant for Payload Operations

    Science.gov (United States)

    Rogers, Mark N.

    1997-01-01

    The broad objective of this expert system software based application was to demonstrate the enhancements and cost savings that can be achieved through expert system software utilization in a spacecraft ground control center. Spacelab provided a valuable proving ground for this advanced software technology; a technology that will be exploited and expanded for future ISS operations. Our specific focus was on demonstrating payload cadre command and control efficiency improvements through the use of "smart" software which monitors flight telemetry, provides enhanced schematic-based data visualization, and performs advanced engineering data analysis.

  13. Identification of the curve of maximum power of photovoltaic modules using simulation software; Identificacao da curva de maxima potencia de modulos FV utilizando softwares de simulacao

    Energy Technology Data Exchange (ETDEWEB)

    Moreira, Andre Pimentel; Ramalho, Geraldo Luis Bezerra; Dias, Samuel Vieira [Centro Federal de Educacao Tecnologica do Ceara (CEFETCE), Fortaleza, CE (Brazil)], emails: apmoreira@cefetce.br, gramalho@cefetce.br, samueldias@cefetce.br; Carvalho, Paulo Cesar Marques de [Universidade Federal do Ceara (PPGEE/UFC), Fortaleza, CE (Brazil). Programa de Pos Graduacao em Engenharia Eletrica], e-mail: carvalho@dee.ufc.br; Borges Neto, Manuel Rangel [Centro Federal de Educacao Tecnologica de Petrolina (CEFETPet), Petrolina, PE (Brazil)], email: rangel@cefetpet.br

    2008-07-01

    This article is presented the study and compared the behaviour of real and simulated a photovoltaic system, through the design and simulation software, Electronic Workbench (MultiSIM 9), AIM-Spice and identifying the point of maximum power (MPP), with the help of modeling software from Matlab. The results of the simulated model were very close to data collected from a real.photovoltaic system. (author)

  14. CLAIRE, an event-driven simulation tool for testing software

    International Nuclear Information System (INIS)

    Raguideau, J.; Schoen, D.; Henry, J.Y.; Boulc'h, J.

    1994-06-01

    CLAIRE is a software tool created to perform validations on executable codes or on specifications of distributed real-time applications for nuclear safety. CLAIRE can be used both to verify the safety properties by modelling the specifications, and also to validate the final code by simulating the behaviour of its equipment and software interfaces. It can be used to observe and provide dynamic control of the simulation process, and also to record changes to the simulated data for off-line analysis. (R.P.)

  15. Software Tools for Stochastic Simulations of Turbulence

    Science.gov (United States)

    2015-08-28

    40] R. D. Richtmyer. Taylor instability in shock acceleration of compressible fluids. Comm. pure Appl. Math , 13(297-319), 1960. 76 [41] R. Samulyak, J...Research Triangle Park, NC 27709-2211 Pure sciences, Applied sciences, Front tracking, Large eddy simulations, Mesh convergence, Stochastic convergence, Weak...Illustration of a component grid with a front crossing solution stencil. Cells in the pure yellow and pure blue regions are assigned different components

  16. RANS Simulations using OpenFOAM Software

    Science.gov (United States)

    2016-01-01

    OpenFOAM offers considerable advantages for Computational Fluid Dynamics (CFD) simulations; it is open source, free of charge, and has the ability...physics, laser- plasma interactions, warhead design, air blast, detonation physics and computational fluid dynamics . Since moving into the Hydrodynamics...private industry as a consultant at the company Xdin. Michel has been working in research projects with computational fluid dynamics focusing on

  17. Development of design and analysis software for advanced nuclear system

    International Nuclear Information System (INIS)

    Wu Yican; Hu Liqin; Long Pengcheng; Luo Yuetong; Li Yazhou; Zeng Qin; Lu Lei; Zhang Junjun; Zou Jun; Xu Dezheng; Bai Yunqing; Zhou Tao; Chen Hongli; Peng Lei; Song Yong; Huang Qunying

    2010-01-01

    A series of professional codes, which are necessary software tools and data libraries for advanced nuclear system design and analysis, were developed by the FDS Team, including the codes of automatic modeling, physics and engineering calculation, virtual simulation and visualization, system engineering and safety analysis and the related database management etc. The development of these software series was proposed as an exercise of development of nuclear informatics. This paper introduced the main functions and key techniques of the software series, as well as some tests and practical applications. (authors)

  18. Stochastic Simulation of Biomolecular Reaction Networks Using the Biomolecular Network Simulator Software

    National Research Council Canada - National Science Library

    Frazier, John; Chusak, Yaroslav; Foy, Brent

    2008-01-01

    .... The software uses either exact or approximate stochastic simulation algorithms for generating Monte Carlo trajectories that describe the time evolution of the behavior of biomolecular reaction networks...

  19. Parallelization of Rocket Engine Simulator Software (PRESS)

    Science.gov (United States)

    Cezzar, Ruknet

    1998-01-01

    We have outlined our work in the last half of the funding period. We have shown how a demo package for RESSAP using MPI can be done. However, we also mentioned the difficulties with the UNIX platform. We have reiterated some of the suggestions made during the presentation of the progress of the at Fourth Annual HBCU Conference. Although we have discussed, in some detail, how TURBDES/PUMPDES software can be run in parallel using MPI, at present, we are unable to experiment any further with either MPI or PVM. Due to X windows not being implemented, we are also not able to experiment further with XPVM, which it will be recalled, has a nice GUI interface. There are also some concerns, on our part, about MPI being an appropriate tool. The best thing about MPr is that it is public domain. Although and plenty of documentation exists for the intricacies of using MPI, little information is available on its actual implementations. Other than very typical, somewhat contrived examples, such as Jacobi algorithm for solving Laplace's equation, there are few examples which can readily be applied to real situations, such as in our case. In effect, the review of literature on both MPI and PVM, and there is a lot, indicate something similar to the enormous effort which was spent on LISP and LISP-like languages as tools for artificial intelligence research. During the development of a book on programming languages [12], when we searched the literature for very simple examples like taking averages, reading and writing records, multiplying matrices, etc., we could hardly find a any! Yet, so much was said and done on that topic in academic circles. It appears that we faced the same problem with MPI, where despite significant documentation, we could not find even a simple example which supports course-grain parallelism involving only a few processes. From the foregoing, it appears that a new direction may be required for more productive research during the extension period (10/19/98 - 10

  20. Honeywell modular automation system computer software documentation

    International Nuclear Information System (INIS)

    Cunningham, L.T.

    1997-01-01

    This document provides a Computer Software Documentation for a new Honeywell Modular Automation System (MAS) being installed in the Plutonium Finishing Plant (PFP). This system will be used to control new thermal stabilization furnaces in HA-21I

  1. Achieving Critical System Survivability Through Software Architectures

    National Research Council Canada - National Science Library

    Knight, John C; Strunk, Elisabeth A

    2006-01-01

    .... In a system with a survivability architecture, under adverse conditions such as system damage or software failures, some desirable function will be eliminated but critical services will be retained...

  2. Gas characterization system software acceptance test procedure

    International Nuclear Information System (INIS)

    Vo, C.V.

    1996-01-01

    This document details the Software Acceptance Testing of gas characterization systems. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases

  3. Gas characterization system software acceptance test report

    International Nuclear Information System (INIS)

    Vo, C.V.

    1996-01-01

    This document details the results of software acceptance testing of gas characterization systems. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases

  4. Software Reliability Issues Concerning Large and Safety Critical Software Systems

    Science.gov (United States)

    Kamel, Khaled; Brown, Barbara

    1996-01-01

    This research was undertaken to provide NASA with a survey of state-of-the-art techniques using in industrial and academia to provide safe, reliable, and maintainable software to drive large systems. Such systems must match the complexity and strict safety requirements of NASA's shuttle system. In particular, the Launch Processing System (LPS) is being considered for replacement. The LPS is responsible for monitoring and commanding the shuttle during test, repair, and launch phases. NASA built this system in the 1970's using mostly hardware techniques to provide for increased reliability, but it did so often using custom-built equipment, which has not been able to keep up with current technologies. This report surveys the major techniques used in industry and academia to ensure reliability in large and critical computer systems.

  5. Software engineering practices for control system reliability

    International Nuclear Information System (INIS)

    S. K. Schaffner; K. S White

    1999-01-01

    This paper will discuss software engineering practices used to improve Control System reliability. The authors begin with a brief discussion of the Software Engineering Institute's Capability Maturity Model (CMM) which is a framework for evaluating and improving key practices used to enhance software development and maintenance capabilities. The software engineering processes developed and used by the Controls Group at the Thomas Jefferson National Accelerator Facility (Jefferson Lab), using the Experimental Physics and Industrial Control System (EPICS) for accelerator control, are described. Examples are given of how their procedures have been used to minimized control system downtime and improve reliability. While their examples are primarily drawn from their experience with EPICS, these practices are equally applicable to any control system. Specific issues addressed include resource allocation, developing reliable software lifecycle processes and risk management

  6. Requirements engineering for software and systems

    CERN Document Server

    Laplante, Phillip A

    2014-01-01

    Solid requirements engineering has increasingly been recognized as the key to improved, on-time and on-budget delivery of software and systems projects. This book provides practical teaching for graduate and professional systems and software engineers. It uses extensive case studies and exercises to help students grasp concepts and techniques. With a focus on software-intensive systems, this text provides a probing and comprehensive review of recent developments in intelligent systems, soft computing techniques, and their diverse applications in manufacturing. The second edition contains 100% revised content and approximately 30% new material

  7. Autonomous Cryogenics Loading Operations Simulation Software: Knowledgebase Autonomous Test Engineer

    Science.gov (United States)

    Wehner, Walter S., Jr.

    2013-01-01

    Working on the ACLO (Autonomous Cryogenics Loading Operations) project I have had the opportunity to add functionality to the physics simulation software known as KATE (Knowledgebase Autonomous Test Engineer), create a new application allowing WYSIWYG (what-you-see-is-what-you-get) creation of KATE schematic files and begin a preliminary design and implementation of a new subsystem that will provide vision services on the IHM (Integrated Health Management) bus. The functionality I added to KATE over the past few months includes a dynamic visual representation of the fluid height in a pipe based on number of gallons of fluid in the pipe and implementing the IHM bus connection within KATE. I also fixed a broken feature in the system called the Browser Display, implemented many bug fixes and made changes to the GUI (Graphical User Interface).

  8. Validation process of ISIS CFD software for fire simulation

    International Nuclear Information System (INIS)

    Lapuerta, C.; Suard, S.; Babik, F.; Rigollet, L.

    2012-01-01

    Fire propagation constitutes a major safety concern in nuclear facilities. In this context, IRSN is developing a CFD code, named ISIS, dedicated to fire simulations. This software is based on a coherent set of models that can be used to describe a fire in large, mechanically ventilated compartments. The system of balance equations obtained by combining these models is discretized in time using fractional step methods, including a pressure correction technique for solving hydrodynamic equations. Discretization in space combines two techniques, each proven in the relevant context: mixed finite elements for hydrodynamic equations and finite volumes for transport equations. ISIS is currently in an advanced stage of verification and validation. The results obtained for a full-scale fire test performed at IRSN are presented.

  9. UFMulti: A new parallel processing software system for HEP

    Science.gov (United States)

    Avery, Paul; White, Andrew

    1989-12-01

    UFMulti is a multiprocessing software package designed for general purpose high energy physics applications, including physics and detector simulation, data reduction and DST physics analysis. The system is particularly well suited for installations where several workstation or computers are connected through a local area network (LAN). The initial configuration of the software is currently running on VAX/VMS machines with a planned extension to ULTRIX, using the new RISC CPUs from Digital, in the near future.

  10. UFMULTI: A new parallel processing software system for HEP

    International Nuclear Information System (INIS)

    Avery, P.; White, A.

    1989-01-01

    UFMulti is a multiprocessing software package designed for general purpose high energy physics applications, including physics and detector simulation, data reduction and DST physics analysis. The system is particularly well suited for installations where several workstations or computers are connected through a local area network (LAN). The initial configuration of the software is currently running on VAX/VMS machines with a planned extension to ULTRIX, using the new RISC CPUs from Digital, in the near future. (orig.)

  11. Construction of new operation interface for the LABIHS simulator using the ELIPSE E3 studio software

    Energy Technology Data Exchange (ETDEWEB)

    Augusto, Silas C.; Oliveira, Mauro V., E-mail: silas@ien.gov.b, E-mail: mvitor@ien.gov.b [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2011-07-01

    The Human-System Interface Laboratory (LABIHS), located at the Instituto de Engenharia Nuclear (IEN), has a compact simulator that simulate the processes of a pressurized water reactor nuclear power plant of 930 MWe of power. This simulator is composed by a HP-UX workstation computer, where the simulation software runs, and a set of computer stations, that represent an advanced control room, where the simulator is operated by software control panels that represent several systems of the simulated nuclear power plant. The current HSIs for the LABIHS simulator was built using iLog software tool. The development of new human-system interfaces (HSIs) for the simulator is one of the research fields of LABIHS. This paper presents the screen components development process for a new HSI for the LABIHS simulator, using the software Elipse{sup TM} E3 Studio. These new components developed using the E3 Studio are similar to the ones used in the current simulator interface. The article shows some comparisons between the component and screen development with Elipse{sup TM} E3 Studio processes and using iLog Studio. (author)

  12. Construction of new operation interface for the LABIHS simulator using the ELIPSE E3 studio software

    International Nuclear Information System (INIS)

    Augusto, Silas C.; Oliveira, Mauro V.

    2011-01-01

    The Human-System Interface Laboratory (LABIHS), located at the Instituto de Engenharia Nuclear (IEN), has a compact simulator that simulate the processes of a pressurized water reactor nuclear power plant of 930 MWe of power. This simulator is composed by a HP-UX workstation computer, where the simulation software runs, and a set of computer stations, that represent an advanced control room, where the simulator is operated by software control panels that represent several systems of the simulated nuclear power plant. The current HSIs for the LABIHS simulator was built using iLog software tool. The development of new human-system interfaces (HSIs) for the simulator is one of the research fields of LABIHS. This paper presents the screen components development process for a new HSI for the LABIHS simulator, using the software Elipse TM E3 Studio. These new components developed using the E3 Studio are similar to the ones used in the current simulator interface. The article shows some comparisons between the component and screen development with Elipse TM E3 Studio processes and using iLog Studio. (author)

  13. Development of a fatigue analysis software system

    International Nuclear Information System (INIS)

    Choi, B. I.; Lee, H. J.; Han, S. W.; Kim, J. Y.; Hwang, K. H.; Kang, J. Y.

    2001-01-01

    A general purpose fatigue analysis software to predict fatigue lives of mechanical components and structures was developed. This software has some characteristic features including functions of searching weak regions on the free surface in order to reduce computing time significantly, a database of fatigue properties for various materials, and an expert system which can assist any users to get more proper results. This software can be used in the environment consists of commercial finite element packages. Using the software developed fatigue analyses for a SAE keyhole specimen and an automobile knuckle were carried out. It was observed that the results were agree well with those from commercial packages

  14. Design and Implementation of Software for Resistance Welding Process Simulations

    DEFF Research Database (Denmark)

    Zhang, Wenqi

    2003-01-01

    Based on long time engineering research and dedicated collaborations with industry, a new welding software, SORPAS, has been developed for simulation of resistance projection and spot welding processes applying the powerful finite element method (FEM). In order to make the software directly usabl...... equipment manufacturers...... by engineers and technicians in industry, all of the important parameters in resistance welding are considered and automatically implemented into the software. With the specially designed graphic user interface for Windows, engineers (even without prior knowledge of FEM) can quickly learn and easily operate...... and utilize the software. All industrial users, including welding engineers from DaimlerChrysler, Volkswangen, PSA Peugeot Citroen, VOLVO, Siemens, ABB and so on, have started using the software just after taking a one-day training course. With the user-friendly facilities for flexible geometric design...

  15. The SCEC Broadband Platform: Open-Source Software for Strong Ground Motion Simulation and Validation

    Science.gov (United States)

    Silva, F.; Goulet, C. A.; Maechling, P. J.; Callaghan, S.; Jordan, T. H.

    2016-12-01

    The Southern California Earthquake Center (SCEC) Broadband Platform (BBP) is a carefully integrated collection of open-source scientific software programs that can simulate broadband (0-100 Hz) ground motions for earthquakes at regional scales. The BBP can run earthquake rupture and wave propagation modeling software to simulate ground motions for well-observed historical earthquakes and to quantify how well the simulated broadband seismograms match the observed seismograms. The BBP can also run simulations for hypothetical earthquakes. In this case, users input an earthquake location and magnitude description, a list of station locations, and a 1D velocity model for the region of interest, and the BBP software then calculates ground motions for the specified stations. The BBP scientific software modules implement kinematic rupture generation, low- and high-frequency seismogram synthesis using wave propagation through 1D layered velocity structures, several ground motion intensity measure calculations, and various ground motion goodness-of-fit tools. These modules are integrated into a software system that provides user-defined, repeatable, calculation of ground-motion seismograms, using multiple alternative ground motion simulation methods, and software utilities to generate tables, plots, and maps. The BBP has been developed over the last five years in a collaborative project involving geoscientists, earthquake engineers, graduate students, and SCEC scientific software developers. The SCEC BBP software released in 2016 can be compiled and run on recent Linux and Mac OS X systems with GNU compilers. It includes five simulation methods, seven simulation regions covering California, Japan, and Eastern North America, and the ability to compare simulation results against empirical ground motion models (aka GMPEs). The latest version includes updated ground motion simulation methods, a suite of new validation metrics and a simplified command line user interface.

  16. Software quality assurance: in large scale and complex software-intensive systems

    NARCIS (Netherlands)

    Mistrik, I.; Soley, R.; Ali, N.; Grundy, J.; Tekinerdogan, B.

    2015-01-01

    Software Quality Assurance in Large Scale and Complex Software-intensive Systems presents novel and high-quality research related approaches that relate the quality of software architecture to system requirements, system architecture and enterprise-architecture, or software testing. Modern software

  17. Software life cycle dynamic simulation model: The organizational performance submodel

    Science.gov (United States)

    Tausworthe, Robert C.

    1985-01-01

    The submodel structure of a software life cycle dynamic simulation model is described. The software process is divided into seven phases, each with product, staff, and funding flows. The model is subdivided into an organizational response submodel, a management submodel, a management influence interface, and a model analyst interface. The concentration here is on the organizational response model, which simulates the performance characteristics of a software development subject to external and internal influences. These influences emanate from two sources: the model analyst interface, which configures the model to simulate the response of an implementing organization subject to its own internal influences, and the management submodel that exerts external dynamic control over the production process. A complete characterization is given of the organizational response submodel in the form of parameterized differential equations governing product, staffing, and funding levels. The parameter values and functions are allocated to the two interfaces.

  18. Investigation of interfacing NPP simulators with PSCAD software

    International Nuclear Information System (INIS)

    Zahedi, P.

    2006-01-01

    This paper demonstrates a new method of interfacing a NPP simulator with the PSCAD software so that the interaction between the plant dynamics and the grid dynamics can be studied. Through this method, data extracted from NPP simulator, as an object, will be communicated to a server running PSCAD software. This paper will illustrate the use of Remote Procedure Calls (RPC) as a distributed, client-server based application used to establish a connection between NPP simulator running on UNIX server and PSCAD running on a PC. Using this method, the called procedure need not exist in the same address space as the calling procedure. Communication protocols available in the NPP simulator are used to export data from the simulator. (author)

  19. Trend Monitoring System (TMS) graphics software

    Science.gov (United States)

    Brown, J. S.

    1979-01-01

    A prototype bus communications systems, which is being used to support the Trend Monitoring System (TMS) and to evaluate the bus concept is considered. A set of FORTRAN-callable graphics subroutines for the host MODCOMP comuter, and an approach to splitting graphics work between the host and the system's intelligent graphics terminals are described. The graphics software in the MODCOMP and the operating software package written for the graphics terminals are included.

  20. Ensuring system security through formal software evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Howell, J A; Fuyat, C [Los Alamos National Lab., NM (United States); Elvy, M [Marble Associates, Boston, MA (United States)

    1992-01-01

    With the increasing use of computer systems and networks to process safeguards information in nuclear facilities, the issue of system and data integrity is receiving worldwide attention. Among the many considerations are validation that the software performs as intended and that the information is adequately protected. Such validations are often requested of the Safeguards Systems Group of the Los Alamos National Laboratory. This paper describes our methodology for performing these software evaluations.

  1. Simulation of Darlington shutdown and regulation systems

    International Nuclear Information System (INIS)

    1986-10-01

    This report describes the development of a simulation of the Darlington Nuclear Generating Station shutdown and regulating systems, DARSIM. The DARSIM program simulates the spatial neutron dynamics, the regulation of the reactor power, and Shutdown System 1, SDS1, and Shutdown System 2, SDS2, software. The DARSIM program operates in the interactive simulation (INSIM) program environment

  2. Selection of bioprocess simulation software for industrial applications.

    Science.gov (United States)

    Shanklin, T; Roper, K; Yegneswaran, P K; Marten, M R

    2001-02-20

    Two commercially available, process-simulation software packages (Aspen Batch Plus v1.2, Aspen Technology, Inc., Cambridge, Massachusetts, and Intelligen SuperPro v3.0, INTELLIGEN, INC., Scotch Plains, Ner Jersey) are evaluated for use in modeling industrial, biotechnology processes. Software is quantitatively evaluated by Kepner-Tregoe Decision Analysis (Kepner and Tregoe, 1981). This evaluation shows that Aspen Batch Plus v1.2 (ABP) and Intelligen SuperPro v3.0 (ISP) can successfully perform specific simulation tasks but do not provide a complete model of all phenomena occurring within a biotechnology process. Software is best suited to provide a format for process management, using material and energy balances to answer scheduling questions, explore equipment change-outs, and calculate cost data. The ability of simulation software to accurately predict unit operation scale-up and optimize bioprocesses is limited. To realistically evaluate the software, a vaccine manufacturing process under development at Merck & Company is simulated. Case studies from the vaccine process are presented as examples of how ABP and ISP can be used to shed light on real-world processing issues. Copyright 2001 John Wiley & Sons, Inc.

  3. Education (gaming simulation: characteristic of software). Kyoiku (gaming simulation: software no tokucho)

    Energy Technology Data Exchange (ETDEWEB)

    Baba, N [Osaka Kyoiku University, Osaka (Japan)

    1992-12-10

    This paper explains history and classification of gaming simulations briefly, and then introduces some instances actually applied to education and training. First, an environmental game by personal computer network gaming system is introduced, which was recently developed. Each player is required to decide on his own investment for products and environmental protection in consideration of the present state of the environment and the managerial situation of his company. If his decision making is not correct, he fails to continue his management due to the aggravation of the environment. In addition, a gaming simulation for the acid rain problem is described, which is being developed in the same way of thinking. Second, an instance of an educational gaming called Sweden Game is introduced, where students learning the mathematical programming carried out the simulation of a pipe-line plan covering six regions of Sweden. Finally, the state of training is explained, in which several kinds of management games are utilized to bring up mainstay leaders in business organizations. 15 refs., 5 figs., 1 tab.

  4. PID controller simulator software for DC motor of gamma scanning

    International Nuclear Information System (INIS)

    Arjoni Amir

    2008-01-01

    Mostly PID controller (Proportional-Integral-Derivative) has been used in industry. For certain applications, it can be used as a Proportional (P) model only, or as a Proportional-Integral (PI) model. The aim of this paper is to design a PID controller simulator software for DC motor which is used in gamma scanning system. A DC motor is described as a plant of SISO (Single Input Single Output) which is used for pulling down the load (detector + casing) and gamma radiation source (Co-60 + container) by using sling cable. A DC motor consist of an armature and a rotor, the equivalent circuit of DC motor is shown in a transfer function equation between output parameter (angular speed DC motor) and input parameter (voltage of DC motor). Methods used for the process of PID controller design is to arrange the PID controller parameter (Kc, Ti, Td) so that there are more PID controller transfer function model which are able to control angular speed of DC motor in stable condition, as design criteria requirement is needed. Design criteria requirement for control system are the settling time < 3 second, overshoot < 5%, rise time = 0.25 second, steady state gain = 1 and peak time < 3 second with step response reference 1 rad/second. The result of simulation gives several models of PID controller in function transfer equation which is similar with design criteria requirement in a equation of function transfer of order 2 for numerator and order 1 for denominator. (author)

  5. A CRITICAL STUDY AND COMPARISON OF MANUFACTURING SIMULATION SOFTWARES USING ANALYTIC HIERARCHY PROCESS

    Directory of Open Access Journals (Sweden)

    ASHU GUPTA

    2010-03-01

    Full Text Available In a period of continuous change in global business environment, organizations, large and small, are finding it increasingly difficult to deal with, and adjust to the demands for such change. Simulation is a powerful tool for allowing designers imagines new systems and enabling them to both quantify and observe behavior. Currently the market offers a variety of simulation software packages. Some are less expensive than others. Some are generic and can be used in a wide variety of application areas while others are more specific. Some have powerful features for modeling while others provide only basic features. Modeling approaches and strategies are different for different packages. Companies are seeking advice about the desirable features of software for manufacturing simulation, depending on the purpose of its use. Because of this, the importance of an adequate approach to simulation software evaluation and comparison is apparent. This paper presents a critical evaluation of four widely used manufacturing simulators: NX-IDEAS, Star-CD, Micro Saint Sharp and ProModel. Following a review of research into simulation software evaluation, an evaluation and comparison of the above simulators is performed. This paper illustrates and assesses the role the Analytic Hierarchy Process (AHP played in simulation software evaluation and selection. The main purpose of this evaluation and comparison is to discover the suitability of certain types of simulators for particular purposes.

  6. The Systems Biology Research Tool: evolvable open-source software

    Directory of Open Access Journals (Sweden)

    Wright Jeremiah

    2008-06-01

    Full Text Available Abstract Background Research in the field of systems biology requires software for a variety of purposes. Software must be used to store, retrieve, analyze, and sometimes even to collect the data obtained from system-level (often high-throughput experiments. Software must also be used to implement mathematical models and algorithms required for simulation and theoretical predictions on the system-level. Results We introduce a free, easy-to-use, open-source, integrated software platform called the Systems Biology Research Tool (SBRT to facilitate the computational aspects of systems biology. The SBRT currently performs 35 methods for analyzing stoichiometric networks and 16 methods from fields such as graph theory, geometry, algebra, and combinatorics. New computational techniques can be added to the SBRT via process plug-ins, providing a high degree of evolvability and a unifying framework for software development in systems biology. Conclusion The Systems Biology Research Tool represents a technological advance for systems biology. This software can be used to make sophisticated computational techniques accessible to everyone (including those with no programming ability, to facilitate cooperation among researchers, and to expedite progress in the field of systems biology.

  7. Design and development of virtual TXP control system software

    International Nuclear Information System (INIS)

    Wang Yunwei; Leng Shan; Liu Zhisheng; Wang Qiang; Shang Yanxia

    2008-01-01

    Taking distributed control system (DCS) of Siemens TELEPERM-XP (TXP) as the simulation object,Virtual TXP (VTXP) control system based on Virtual DCS with high fidelity and reliability was designed and developed on the platform of Windows. In the process of development, the method of object-oriented modeling and modularization program design are adopted, C++ language and technologies such as multithreading, ActiveX control, Socket network communication are used, to realize the wide range dynamic simulation and recreate the functions of the hardware and software of real TXP. This paper puts emphasis on the design and realization of Control server and Communication server. The development of Virtual TXP control system software is with great effect on the construction of simulation system and the design, commission, verification and maintenance of control system in large-scale power plants, nuclear power plants and combined cycle power plants. (authors)

  8. Software development infrastructure for the HYBRID modeling and simulation project

    International Nuclear Information System (INIS)

    Epiney, Aaron S.; Kinoshita, Robert A.; Kim, Jong Suk; Rabiti, Cristian; Greenwood, M. Scott

    2016-01-01

    One of the goals of the HYBRID modeling and simulation project is to assess the economic viability of hybrid systems in a market that contains renewable energy sources like wind. The idea is that it is possible for the nuclear plant to sell non-electric energy cushions, which absorb (at least partially) the volatility introduced by the renewable energy sources. This system is currently modeled in the Modelica programming language. To assess the economics of the system, an optimization procedure is trying to find the minimal cost of electricity production. The RAVEN code is used as a driver for the whole problem. It is assumed that at this stage, the HYBRID modeling and simulation framework can be classified as non-safety “research and development” software. The associated quality level is Quality Level 3 software. This imposes low requirements on quality control, testing and documentation. The quality level could change as the application development continues.Despite the low quality requirement level, a workflow for the HYBRID developers has been defined that include a coding standard and some documentation and testing requirements. The repository performs automated unit testing of contributed models. The automated testing is achieved via an open-source python script called BuildingsP from Lawrence Berkeley National Lab. BuildingsPy runs Modelica simulation tests using Dymola in an automated manner and generates and runs unit tests from Modelica scripts written by developers. In order to assure effective communication between the different national laboratories a biweekly videoconference has been set-up, where developers can report their progress and issues. In addition, periodic face-face meetings are organized intended to discuss high-level strategy decisions with management. A second means of communication is the developer email list. This is a list to which everybody can send emails that will be received by the collective of the developers and managers

  9. Software development infrastructure for the HYBRID modeling and simulation project

    Energy Technology Data Exchange (ETDEWEB)

    Epiney, Aaron S. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kinoshita, Robert A. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kim, Jong Suk [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Greenwood, M. Scott [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-09-01

    One of the goals of the HYBRID modeling and simulation project is to assess the economic viability of hybrid systems in a market that contains renewable energy sources like wind. The idea is that it is possible for the nuclear plant to sell non-electric energy cushions, which absorb (at least partially) the volatility introduced by the renewable energy sources. This system is currently modeled in the Modelica programming language. To assess the economics of the system, an optimization procedure is trying to find the minimal cost of electricity production. The RAVEN code is used as a driver for the whole problem. It is assumed that at this stage, the HYBRID modeling and simulation framework can be classified as non-safety “research and development” software. The associated quality level is Quality Level 3 software. This imposes low requirements on quality control, testing and documentation. The quality level could change as the application development continues.Despite the low quality requirement level, a workflow for the HYBRID developers has been defined that include a coding standard and some documentation and testing requirements. The repository performs automated unit testing of contributed models. The automated testing is achieved via an open-source python script called BuildingsP from Lawrence Berkeley National Lab. BuildingsPy runs Modelica simulation tests using Dymola in an automated manner and generates and runs unit tests from Modelica scripts written by developers. In order to assure effective communication between the different national laboratories a biweekly videoconference has been set-up, where developers can report their progress and issues. In addition, periodic face-face meetings are organized intended to discuss high-level strategy decisions with management. A second means of communication is the developer email list. This is a list to which everybody can send emails that will be received by the collective of the developers and managers

  10. Coordination Approaches for Complex Software Systems

    NARCIS (Netherlands)

    Bosse, T.; Hoogendoorn, M.; Treur, J.

    2006-01-01

    This document presents the results of a collaboration between the Vrije Universiteit Amsterdam, Department of Artificial Intelligence and Force Vision to investigate coordination approaches for complex software systems. The project was funded by Force Vision.

  11. Architecting Fault-Tolerant Software Systems

    NARCIS (Netherlands)

    Sözer, Hasan

    2009-01-01

    The increasing size and complexity of software systems makes it hard to prevent or remove all possible faults. Faults that remain in the system can eventually lead to a system failure. Fault tolerance techniques are introduced for enabling systems to recover and continue operation when they are

  12. Application of PSpice in simulation of a photovoltaic (PV) system ...

    African Journals Online (AJOL)

    There are two approaches in computer simulation of any system- developing custom software from the scratch or application of one of the commercially available software packages. In the later approach, either dedicated simulating software can be used or general-purpose software can be adapted to suit particular needs.

  13. Wind flow simulation over flat terrain using CFD based software

    International Nuclear Information System (INIS)

    Petrov, Peter; Terziev, Angel; Genovski, Ivan

    2009-01-01

    Velocity distribution recognition over definite place (terrain) is very important because due to that the zones with high energy potential could be defined (the fields with high velocities). This is a precondition for optimal wind turbine generators micro-sitting. In current work a simulation of the open flow over the flat terrain using the CFD based software is reviewed. The simulations are made of a real fluid flow in order to be defined the velocity fields over the terrain

  14. A Software Development Simulation Model of a Spiral Process

    OpenAIRE

    Carolyn Mizell; Linda Malone

    2009-01-01

    This paper will present a discrete event simulation model of a spiral development lifecycle that can be used to analyze cost and schedule effects of using such a process in comparison to a waterfall process. There is a need for simulation models of software development processes other than the waterfall due to new processes becoming more widely used in order to overcome the limitations of the traditional waterfall lifecycle. The use of a spiral process can make the inherently difficult job of...

  15. A Software Architecture for Simulation Support in Building Automation

    Directory of Open Access Journals (Sweden)

    Sergio Leal

    2014-07-01

    Full Text Available Building automation integrates the active components in a building and, thus, has to connect components of different industries. The goal is to provide reliable and efficient operation. This paper describes how simulation can support building automation and how the deployment process of simulation assisted building control systems can be structured. We look at the process as a whole and map it to a set of formally described workflows that can partly be automated. A workbench environment supports the process execution by means of improved planning, collaboration and deployment. This framework allows integration of existing tools, as well as manual tasks, and is, therefore, many more intricate than regular software deployment tools. The complex environment of building commissioning requires expertise in different domains, especially lighting, heating, ventilation, air conditioning, measurement and control technology, as well as energy efficiency; therefore, we present a framework for building commissioning and describe a deployment process that is capable of supporting the various phases of this approach.

  16. Creating a simulation model of software testing using Simulink package

    Directory of Open Access Journals (Sweden)

    V. M. Dubovoi

    2016-12-01

    Full Text Available The determination of the solution model of software testing that allows prediction both the whole process and its specific stages is actual for IT-industry. The article focuses on solving this problem. The aim of the article is prediction the time and improvement the quality of software testing. The analysis of the software testing process shows that it can be attributed to the branched cyclic technological processes because it is cyclical with decision-making on control operations. The investigation uses authors' previous works andsoftware testing process method based on Markov model. The proposed method enables execution the prediction for each software module, which leads to better decision-making of each controlled suboperation of all processes. Simulink simulation model shows implementation and verification of results of proposed technique. Results of the research have practically implemented in the IT-industry.

  17. Advanced Languages for Systems Software

    Science.gov (United States)

    1994-01-01

    in performance. Specific examples of well-structured systems include the microkernel architecture of the Mach 3.0 operating system and the modular... microkernels as a first step towards building a completely modular operating system from a set of composable services. However, just as the idea of a...microprotocol in the x-kernel is a design principle, rather than a formally realized construct, the modularity of microkernels is largely a matter of

  18. Adaptive intrusion data system (AIDS) software routines

    International Nuclear Information System (INIS)

    Corlis, N.E.

    1980-07-01

    An Adaptive Intrusion Data System (AIDS) was developed to collect information from intrusion alarm sensors as part of an evaluation system to improve sensor performance. AIDS is a unique digital data-compression, storage, and formatting system; it also incorporates a capability for video selection and recording for assessment of the sensors monitored by the system. The system is software reprogrammable to numerous configurations that may be used for the collection of environmental, bilevel, analog, and video data. This report describes the software routines that control the different AIDS data-collection modes, the diagnostic programs to test the operating hardware, and the data format. Sample data printouts are also included

  19. Simulation and visualization tool design for robot software

    NARCIS (Netherlands)

    Lu, Zhou; Ran, Tjalling; Broenink, Johannes F.; Chalmers, K.; Pedersen, J.B.

    2016-01-01

    Modern embedded systems are designed for multiple and increasingly demanding tasks. Complex concurrent software is required by multi-task automated service robotics for implementing their challenging (control) algorithms. TERRA is a communicating Sequential Processes (CSP) algebra-based Eclipse

  20. Development of CFD software for the simulation of thermal hydraulics in advanced nuclear reactors. Final report

    International Nuclear Information System (INIS)

    Bachar, Abdelaziz; Haslinger, Wolfgang; Scheuerer, Georg; Theodoridis, Georgios

    2015-01-01

    The objectives of the project were: Improvement of the simulation accuracy for nuclear reactor thermo-hydraulics by coupling system codes with three-dimensional CFD software; Extension of CFD software to predict thermo-hydraulics in advanced reactor concepts; Validation of the CFD software by simulation different UPTF TRAM-C test cases and development of best practice guidelines. The CFD module was based on the ANSYS CFD software and the system code ATHLET of GRS. All three objectives were met: The coupled ATHLET-ANSYS CFD software is in use at GRS and TU Muenchen. Besides the test cases described in the report, it has been used for other applications, for instance the TALL-3D experiment of KTH Stockholm. The CFD software was extended with material properties for liquid metals, and validated using existing data. Several new concepts were tested when applying the CFD software to the UPTF test cases: Simulations with Conjugate Heat Transfer (CHT) were performed for the first time. This led to better agreement between predictions and data and reduced uncertainties when applying temperature boundary conditions. The meshes for the CHT simulation were also used for a coupled fluid-structure-thermal analysis which was another novelty. The results of the multi-physics analysis showed plausible results for the mechanical and thermal stresses. The workflow developed as part of the current project can be directly used for industrial nuclear reactor simulations. Finally, simulations for two-phase flows with and without interfacial mass transfer were performed. These showed good agreement with data. However, a persisting problem for the simulation of multi-phase flows are the long simulation times which make use for industrial applications difficult.

  1. Clinical software for MR imaging system, 4

    International Nuclear Information System (INIS)

    Shimizu, Koji; Kasai, Akira; Okamura, Shoichi

    1992-01-01

    Magnetic resonance imaging continues to elicit new application software through the recent technological advances of MR equipment. This paper describes several applications of our newly developed clinical software. The fast SE sequence (RISE) has proved to reduce routine examination time and to improve image quality, and ultra-fast FE sequence (SMASH) was found to extend the diagnostic capabilities in the field of cardiac study. Diffusion/perfusion imaging achieved in our MR system showed significant promise for providing novel information regarding tissue characterization. Furthermore, Image quality and practicalities of MR angiography have been improved by advanced imaging sequences and sophisticated post-processing software. (author)

  2. Implementing a modeling software for animated protein-complex interactions using a physics simulation library.

    Science.gov (United States)

    Ueno, Yutaka; Ito, Shuntaro; Konagaya, Akihiko

    2014-12-01

    To better understand the behaviors and structural dynamics of proteins within a cell, novel software tools are being developed that can create molecular animations based on the findings of structural biology. This study proposes our method developed based on our prototypes to detect collisions and examine the soft-body dynamics of molecular models. The code was implemented with a software development toolkit for rigid-body dynamics simulation and a three-dimensional graphics library. The essential functions of the target software system included the basic molecular modeling environment, collision detection in the molecular models, and physical simulations of the movement of the model. Taking advantage of recent software technologies such as physics simulation modules and interpreted scripting language, the functions required for accurate and meaningful molecular animation were implemented efficiently.

  3. Evaluation of the litcit software for thermal simulation of superficial lasers such as hair removal lasers

    Directory of Open Access Journals (Sweden)

    Shirkavand A

    2007-01-01

    Full Text Available Background and Objectives : In this study, we evaluate LITCIT software for its application as a thermal simulation software for superficial hair removal laser systems. Materials and Methods: Two articles were used as our references. Complete information regarding the tissues, such as optical/thermal properties and geometrical modeling and also the laser systems such as wavelength, spot size, pulse duration and fluence were extracted from these texts. Then, this information regarding the tissues and systems was entered into the LITCIT simulation software. Further, we ran the program and saved the results. Finally, we compared our results with the results in references and evaluated the. Results : Output results of the LITCIT show that they are consistent with the results of references that were calculated with a different thermal modeling. Such a small average error shows the accuracy of the software for simulation and calculating the temperature. Conclusions : This simulating software has a good ability to be used as a treatment planning software for superficial lasers. Thus, it can be used for the optimization of treatment parameters and protocols.

  4. MPS [Multiparticle Spectrometer] data acquisition software system

    International Nuclear Information System (INIS)

    Saulys, A.C.; Etkin, A.; Foley, K.J.

    1989-01-01

    A description of the software for a FASTBUS based data acquisition system in use at the Brookhaven National Laboratory Multiparticle Spectrometer is presented. Data reading and formatting is done by the SLAC Scanner Processors (SSP's) resident in the FASTBUS system. A multiprocess software system on VAX computers is used to communicate with the SSP's, record the data, and monitor on-line the progress of high energy and heavy ion experiments. The structure and the performance of this system are discussed. 4 refs., 1 fig

  5. Automated software configuration in the MONSOON system

    Science.gov (United States)

    Daly, Philip N.; Buchholz, Nick C.; Moore, Peter C.

    2004-09-01

    MONSOON is the next generation OUV-IR controller project being developed at NOAO. The design is flexible, emphasizing code re-use, maintainability and scalability as key factors. The software needs to support widely divergent detector systems ranging from multi-chip mosaics (for LSST, QUOTA, ODI and NEWFIRM) down to large single or multi-detector laboratory development systems. In order for this flexibility to be effective and safe, the software must be able to configure itself to the requirements of the attached detector system at startup. The basic building block of all MONSOON systems is the PAN-DHE pair which make up a single data acquisition node. In this paper we discuss the software solutions used in the automatic PAN configuration system.

  6. Automated Cryocooler Monitor and Control System Software

    Science.gov (United States)

    Britchcliffe, Michael J.; Conroy, Bruce L.; Anderson, Paul E.; Wilson, Ahmad

    2011-01-01

    This software is used in an automated cryogenic control system developed to monitor and control the operation of small-scale cryocoolers. The system was designed to automate the cryogenically cooled low-noise amplifier system described in "Automated Cryocooler Monitor and Control System" (NPO-47246), NASA Tech Briefs, Vol. 35, No. 5 (May 2011), page 7a. The software contains algorithms necessary to convert non-linear output voltages from the cryogenic diode-type thermometers and vacuum pressure and helium pressure sensors, to temperature and pressure units. The control function algorithms use the monitor data to control the cooler power, vacuum solenoid, vacuum pump, and electrical warm-up heaters. The control algorithms are based on a rule-based system that activates the required device based on the operating mode. The external interface is Web-based. It acts as a Web server, providing pages for monitor, control, and configuration. No client software from the external user is required.

  7. Upgrades to the Probabilistic NAS Platform Air Traffic Simulation Software

    Science.gov (United States)

    Hunter, George; Boisvert, Benjamin

    2013-01-01

    This document is the final report for the project entitled "Upgrades to the Probabilistic NAS Platform Air Traffic Simulation Software." This report consists of 17 sections which document the results of the several subtasks of this effort. The Probabilistic NAS Platform (PNP) is an air operations simulation platform developed and maintained by the Saab Sensis Corporation. The improvements made to the PNP simulation include the following: an airborne distributed separation assurance capability, a required time of arrival assignment and conformance capability, and a tactical and strategic weather avoidance capability.

  8. Software for simulation and design of neutron scattering instrumentation

    DEFF Research Database (Denmark)

    Bertelsen, Mads

    designed using the software. The Union components uses a new approach to simulation of samples in McStas. The properties of a sample are split into geometrical and material, simplifying user input, and allowing the construction of complicated geometries such as sample environments. Multiple scattering...... from conventional choices. Simulation of neutron scattering instrumentation is used when designing instrumentation, but also to understand instrumental effects on the measured scattering data. The Monte Carlo ray-tracing package McStas is among the most popular, capable of simulating the path of each...... neutron through the instrument using an easy to learn language. The subject of the defended thesis is contributions to the McStas language in the form of the software package guide_bot and the Union components.The guide_bot package simplifies the process of optimizing neutron guides by writing the Mc...

  9. Coupling photon Monte Carlo simulation and CAD software. Application to X-ray nondestructive evaluation

    International Nuclear Information System (INIS)

    Tabary, J.; Gliere, A.

    2001-01-01

    A Monte Carlo radiation transport simulation program, EGS Nova, and a computer aided design software, BRL-CAD, have been coupled within the framework of Sindbad, a nondestructive evaluation (NDE) simulation system. In its current status, the program is very valuable in a NDE laboratory context, as it helps simulate the images due to the uncollided and scattered photon fluxes in a single NDE software environment, without having to switch to a Monte Carlo code parameters set. Numerical validations show a good agreement with EGS4 computed and published data. As the program's major drawback is the execution time, computational efficiency improvements are foreseen. (orig.)

  10. The development of test software for the inadequate core cooling monitoring system

    International Nuclear Information System (INIS)

    Lee, Soon Sung.

    1996-06-01

    The test software including the ICCMS simulator which is necessary for dynamic test for the ICCMS software in PWR is developed. The developed dynamic test software consists of the module test simulator, the integration test simulator, and the test result analyser. The simulator was programmed by C language according to the same algorithm requirements for the FORTRAN version ICCMS software, and also for the Factory Acceptance Test (FAT). And the simulator can be used as training tool for the reactor operator and system development tool for the performance improvement. (author). 4 tabs., 8 figs., 11 refs

  11. A Reference Model for Software and System Inspections. White Paper

    Science.gov (United States)

    He, Lulu; Shull, Forrest

    2009-01-01

    Software Quality Assurance (SQA) is an important component of the software development process. SQA processes provide assurance that the software products and processes in the project life cycle conform to their specified requirements by planning, enacting, and performing a set of activities to provide adequate confidence that quality is being built into the software. Typical techniques include: (1) Testing (2) Simulation (3) Model checking (4) Symbolic execution (5) Management reviews (6) Technical reviews (7) Inspections (8) Walk-throughs (9) Audits (10) Analysis (complexity analysis, control flow analysis, algorithmic analysis) (11) Formal method Our work over the last few years has resulted in substantial knowledge about SQA techniques, especially the areas of technical reviews and inspections. But can we apply the same QA techniques to the system development process? If yes, what kind of tailoring do we need before applying them in the system engineering context? If not, what types of QA techniques are actually used at system level? And, is there any room for improvement.) After a brief examination of the system engineering literature (especially focused on NASA and DoD guidance) we found that: (1) System and software development process interact with each other at different phases through development life cycle (2) Reviews are emphasized in both system and software development. (Figl.3). For some reviews (e.g. SRR, PDR, CDR), there are both system versions and software versions. (3) Analysis techniques are emphasized (e.g. Fault Tree Analysis, Preliminary Hazard Analysis) and some details are given about how to apply them. (4) Reviews are expected to use the outputs of the analysis techniques. In other words, these particular analyses are usually conducted in preparation for (before) reviews. The goal of our work is to explore the interaction between the Quality Assurance (QA) techniques at the system level and the software level.

  12. Concept of software interface for BCI systems

    Science.gov (United States)

    Svejda, Jaromir; Zak, Roman; Jasek, Roman

    2016-06-01

    Brain Computer Interface (BCI) technology is intended to control external system by brain activity. One of main part of such system is software interface, which carries about clear communication between brain and either computer or additional devices connected to computer. This paper is organized as follows. Firstly, current knowledge about human brain is briefly summarized to points out its complexity. Secondly, there is described a concept of BCI system, which is then used to build an architecture of proposed software interface. Finally, there are mentioned disadvantages of sensing technology discovered during sensing part of our research.

  13. A Multiprocessor Operating System Simulator

    Science.gov (United States)

    Johnston, Gary M.; Campbell, Roy H.

    1988-01-01

    This paper describes a multiprocessor operating system simulator that was developed by the authors in the Fall semester of 1987. The simulator was built in response to the need to provide students with an environment in which to build and test operating system concepts as part of the coursework of a third-year undergraduate operating systems course. Written in C++, the simulator uses the co-routine style task package that is distributed with the AT&T C++ Translator to provide a hierarchy of classes that represents a broad range of operating system software and hardware components. The class hierarchy closely follows that of the 'Choices' family of operating systems for loosely- and tightly-coupled multiprocessors. During an operating system course, these classes are refined and specialized by students in homework assignments to facilitate experimentation with different aspects of operating system design and policy decisions. The current implementation runs on the IBM RT PC under 4.3bsd UNIX.

  14. Cost Analysis of Poor Quality Using a Software Simulation

    Directory of Open Access Journals (Sweden)

    Jana Fabianová

    2017-02-01

    Full Text Available The issues of quality, cost of poor quality and factors affecting quality are crucial to maintaining a competitiveness regarding to business activities. Use of software applications and computer simulation enables more effective quality management. Simulation tools offer incorporating the variability of more variables in experiments and evaluating their common impact on the final output. The article presents a case study focused on the possibility of using computer simulation Monte Carlo in the field of quality management. Two approaches for determining the cost of poor quality are introduced here. One from retrospective scope of view, where the cost of poor quality and production process are calculated based on historical data. The second approach uses the probabilistic characteristics of the input variables by means of simulation, and reflects as a perspective view of the costs of poor quality. Simulation output in the form of a tornado and sensitivity charts complement the risk analysis.

  15. A software simulator for the SPICA Safari instrument

    International Nuclear Information System (INIS)

    Naylor, D A; Hayton, D J; Lindner, J V; Sadeghi, B

    2011-01-01

    A software simulator that has been developed for the Safari instrument proposed for the SPace Infrared telescope for Cosmology and Astrophysics (SPICA) mission is presented. The simulator can ingest a range of realistic input spectra and, following a thorough radiative transfer analysis, calculates the power reaching the detector as a function of the optical path difference within the interferometer. The simulator is modular in design so that it can be easily modified to ingest test data as they become available. The simulator will not only find use during the design phase of the Safari instrument, but also during ground performance verification campaigns of the flight model. Through validation of the simulator on ground test data, it will be possible to predict accurately the in-orbit performance of the Safari instrument

  16. Verification and validation of control system software

    International Nuclear Information System (INIS)

    Munro, J.K. Jr.; Kisner, R.A.; Bhadtt, S.C.

    1991-01-01

    The following guidelines are proposed for verification and validation (V ampersand V) of nuclear power plant control system software: (a) use risk management to decide what and how much V ampersand V is needed; (b) classify each software application using a scheme that reflects what type and how much V ampersand V is needed; (c) maintain a set of reference documents with current information about each application; (d) use Program Inspection as the initial basic verification method; and (e) establish a deficiencies log for each software application. The following additional practices are strongly recommended: (a) use a computer-based configuration management system to track all aspects of development and maintenance; (b) establish reference baselines of the software, associated reference documents, and development tools at regular intervals during development; (c) use object-oriented design and programming to promote greater software reliability and reuse; (d) provide a copy of the software development environment as part of the package of deliverables; and (e) initiate an effort to use formal methods for preparation of Technical Specifications. The paper provides background information and reasons for the guidelines and recommendations. 3 figs., 3 tabs

  17. Software fault tolerance in computer operating systems

    Science.gov (United States)

    Iyer, Ravishankar K.; Lee, Inhwan

    1994-01-01

    This chapter provides data and analysis of the dependability and fault tolerance for three operating systems: the Tandem/GUARDIAN fault-tolerant system, the VAX/VMS distributed system, and the IBM/MVS system. Based on measurements from these systems, basic software error characteristics are investigated. Fault tolerance in operating systems resulting from the use of process pairs and recovery routines is evaluated. Two levels of models are developed to analyze error and recovery processes inside an operating system and interactions among multiple instances of an operating system running in a distributed environment. The measurements show that the use of process pairs in Tandem systems, which was originally intended for tolerating hardware faults, allows the system to tolerate about 70% of defects in system software that result in processor failures. The loose coupling between processors which results in the backup execution (the processor state and the sequence of events occurring) being different from the original execution is a major reason for the measured software fault tolerance. The IBM/MVS system fault tolerance almost doubles when recovery routines are provided, in comparison to the case in which no recovery routines are available. However, even when recovery routines are provided, there is almost a 50% chance of system failure when critical system jobs are involved.

  18. HEP Software Foundation Community White Paper Working Group - Detector Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Apostolakis, J; et al.

    2018-03-12

    A working group on detector simulation was formed as part of the high-energy physics (HEP) Software Foundation's initiative to prepare a Community White Paper that describes the main software challenges and opportunities to be faced in the HEP field over the next decade. The working group met over a period of several months in order to review the current status of the Full and Fast simulation applications of HEP experiments and the improvements that will need to be made in order to meet the goals of future HEP experimental programmes. The scope of the topics covered includes the main components of a HEP simulation application, such as MC truth handling, geometry modeling, particle propagation in materials and fields, physics modeling of the interactions of particles with matter, the treatment of pileup and other backgrounds, as well as signal processing and digitisation. The resulting work programme described in this document focuses on the need to improve both the software performance and the physics of detector simulation. The goals are to increase the accuracy of the physics models and expand their applicability to future physics programmes, while achieving large factors in computing performance gains consistent with projections on available computing resources.

  19. Honeywell Modular Automation System Computer Software Documentation

    International Nuclear Information System (INIS)

    CUNNINGHAM, L.T.

    1999-01-01

    This document provides a Computer Software Documentation for a new Honeywell Modular Automation System (MAS) being installed in the Plutonium Finishing Plant (PFP). This system will be used to control new thermal stabilization furnaces in HA-211 and vertical denitration calciner in HC-230C-2

  20. Software for managing multicrate FASTBUS Systems

    International Nuclear Information System (INIS)

    Deiss, S.R.; Gustavson, D.B.

    1982-10-01

    The FASTBUS System Manager software that was designed and implemented on an LSI-11 system using PASCAL is described. Particular attention is given to the file structures, file access mechanisms, and basic routing algorithms. Portability to other machines and languages is described

  1. TAP II Beamforming System Software Final Report

    Science.gov (United States)

    1977-05-01

    recommended. Ten averages may be sufficient for some wave studies . 2.3.1.4 (U) The TYPE OF WEIGHTING WINDOW is selected according to the characteristics...and FIFF1T), the AP s ource code assembler (APAL), the AP Simulator ( APSIM ), and the AP software Debug program (IIWDBUG). UNCLASSIFiED...PROCESSING. Thia is a moderately complex pro gram uhich utilizes the AP-120B array processor. For detailed descrip- "tion of the process, study of the

  2. The validation of an infrared simulation system

    CSIR Research Space (South Africa)

    De Waal, A

    2013-08-01

    Full Text Available theoretical validation framework. This paper briefly describes the procedure used to validate software models in an infrared system simulation, and provides application examples of this process. The discussion includes practical validation techniques...

  3. Software Intensive Systems Cost and Schedule Estimation

    Science.gov (United States)

    2013-06-13

    of labor counted in or across each activity. The activity data in  the SRDR is reported following the [ ISO   12207 ] processes for software development...Release  Table 19 ISO /IEC 12207 Development Activities System requirements analysis System architectural design A ct iv iti es in S RD R da ta... 12207 ]  ISO /IEC  12207 , International Standard on Information Technology  Software Lifecycle Processes, International Organization for  Standardization

  4. Biomolecular structure refinement using the GROMOS simulation software

    International Nuclear Information System (INIS)

    Schmid, Nathan; Allison, Jane R.; Dolenc, Jožica; Eichenberger, Andreas P.; Kunz, Anna-Pitschna E.; Gunsteren, Wilfred F. van

    2011-01-01

    For the understanding of cellular processes the molecular structure of biomolecules has to be accurately determined. Initial models can be significantly improved by structure refinement techniques. Here, we present the refinement methods and analysis techniques implemented in the GROMOS software for biomolecular simulation. The methodology and some implementation details of the computation of NMR NOE data, 3 J-couplings and residual dipolar couplings, X-ray scattering intensities from crystals and solutions and neutron scattering intensities used in GROMOS is described and refinement strategies and concepts are discussed using example applications. The GROMOS software allows structure refinement combining different types of experimental data with different types of restraining functions, while using a variety of methods to enhance conformational searching and sampling and the thermodynamically calibrated GROMOS force field for biomolecular simulation.

  5. Biomolecular structure refinement using the GROMOS simulation software

    Energy Technology Data Exchange (ETDEWEB)

    Schmid, Nathan; Allison, Jane R.; Dolenc, Jozica; Eichenberger, Andreas P.; Kunz, Anna-Pitschna E.; Gunsteren, Wilfred F. van, E-mail: wfvgn@igc.phys.chem.ethz.ch [Swiss Federal Institute of Technology ETH, Laboratory of Physical Chemistry (Switzerland)

    2011-11-15

    For the understanding of cellular processes the molecular structure of biomolecules has to be accurately determined. Initial models can be significantly improved by structure refinement techniques. Here, we present the refinement methods and analysis techniques implemented in the GROMOS software for biomolecular simulation. The methodology and some implementation details of the computation of NMR NOE data, {sup 3}J-couplings and residual dipolar couplings, X-ray scattering intensities from crystals and solutions and neutron scattering intensities used in GROMOS is described and refinement strategies and concepts are discussed using example applications. The GROMOS software allows structure refinement combining different types of experimental data with different types of restraining functions, while using a variety of methods to enhance conformational searching and sampling and the thermodynamically calibrated GROMOS force field for biomolecular simulation.

  6. Software analysis by simulation for nuclear plant availability and safety goals

    International Nuclear Information System (INIS)

    Lapassat, A.M.; Segalard, J.; Salichon, M.; Le Meur, M.; Boulc'h, J.

    1988-01-01

    The microprocessors utilisation for monitoring protection and safety of nuclear reactor has become reality in the eighties. The authorities responsible for reactor safety systems have considered the necessity of the correct functioning of reactor control systems. The problems take off, when analysis of software, has led us in a first time to develop a completely software tool of verification and validation of programs and specifications. The CEA (French Atomic Energie Commission) responsible of reliable distributed techniques of nuclear plant discusses in this paper the software test and simulation tools used to analyse real-time software. The tool O.S.T. make part of a big program of help for the conception and the evaluation for the systems' fault tolerance which the European ESPRIT SMART no. 1609 (System Measurement and Architecture Technique) will be the kernel [fr

  7. A Stigmergy Approach for Open Source Software Developer Community Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Cui, Xiaohui [ORNL; Beaver, Justin M [ORNL; Potok, Thomas E [ORNL; Pullum, Laura L [ORNL; Treadwell, Jim N [ORNL

    2009-01-01

    The stigmergy collaboration approach provides a hypothesized explanation about how online groups work together. In this research, we presented a stigmergy approach for building an agent based open source software (OSS) developer community collaboration simulation. We used group of actors who collaborate on OSS projects as our frame of reference and investigated how the choices actors make in contribution their work on the projects determinate the global status of the whole OSS projects. In our simulation, the forum posts and project codes served as the digital pheromone and the modified Pierre-Paul Grasse pheromone model is used for computing developer agent behaviors selection probability.

  8. A Software Development Simulation Model of a Spiral Process

    Science.gov (United States)

    Mizell, Carolyn; Malone, Linda

    2007-01-01

    There is a need for simulation models of software development processes other than the waterfall because processes such as spiral development are becoming more and more popular. The use of a spiral process can make the inherently difficult job of cost and schedule estimation even more challenging due to its evolutionary nature, but this allows for a more flexible process that can better meet customers' needs. This paper will present a discrete event simulation model of spiral development that can be used to analyze cost and schedule effects of using such a process in comparison to a waterfall process.

  9. Numerical simulations of progressive hardening by using ABAQUS FEA software

    Directory of Open Access Journals (Sweden)

    Domański Tomasz

    2018-01-01

    Full Text Available The paper concerns numerical simulations of progressive hardening include phase transformations in solid state of steel. Abaqus FEA software is used for numerical analysis of temperature field and phase transformations. Numerical subroutines, written in fortran programming language are used in computer simulations where models of the distribution of movable heat source, kinetics of phase transformations in solid state as well as thermal and structural strain are implemented. Model for evaluation of fractions of phases and their kinetics is based on continuous heating diagram and continuous cooling diagram. The numerical analysis of thermal fields, phase fractions and strain associated progressive hardening of elements made of steel were done.

  10. A User-Friendly Software Package for HIFU Simulation

    Science.gov (United States)

    Soneson, Joshua E.

    2009-04-01

    A freely-distributed, MATLAB (The Mathworks, Inc., Natick, MA)-based software package for simulating axisymmetric high-intensity focused ultrasound (HIFU) beams and their heating effects is discussed. The package (HIFU_Simulator) consists of a propagation module which solves the Khokhlov-Zabolotskaya-Kuznetsov (KZK) equation and a heating module which solves Pennes' bioheat transfer (BHT) equation. The pressure, intensity, heating rate, temperature, and thermal dose fields are computed, plotted, the output is released to the MATLAB workspace for further user analysis or postprocessing.

  11. Model-integrating software components engineering flexible software systems

    CERN Document Server

    Derakhshanmanesh, Mahdi

    2015-01-01

    In his study, Mahdi Derakhshanmanesh builds on the state of the art in modeling by proposing to integrate models into running software on the component-level without translating them to code. Such so-called model-integrating software exploits all advantages of models: models implicitly support a good separation of concerns, they are self-documenting and thus improve understandability and maintainability and in contrast to model-driven approaches there is no synchronization problem anymore between the models and the code generated from them. Using model-integrating components, software will be

  12. Improving Software Systems By Flow Control Analysis

    Directory of Open Access Journals (Sweden)

    Piotr Poznanski

    2012-01-01

    Full Text Available Using agile methods during the implementation of the system that meets mission critical requirements can be a real challenge. The change in the system built of dozens or even hundreds of specialized devices with embedded software requires the cooperation of a large group of engineers. This article presents a solution that supports parallel work of groups of system analysts and software developers. Deployment of formal rules to the requirements written in natural language enables using formal analysis of artifacts being a bridge between software and system requirements. Formalism and textual form of requirements allowed the automatic generation of message flow graph for the (sub system, called the “big-picture-model”. Flow diagram analysis helped to avoid a large number of defects whose repair cost in extreme cases could undermine the legitimacy of agile methods in projects of this scale. Retrospectively, a reduction of technical debt was observed. Continuous analysis of the “big picture model” improves the control of the quality parameters of the software architecture. The article also tries to explain why the commercial platform based on UML modeling language may not be sufficient in projects of this complexity.

  13. Coupling an analytical description of anti-scatter grids with simulation software of radiographic systems using Monte Carlo code; Couplage d'une methode de description analytique de grilles anti diffusantes avec un logiciel de simulation de systemes radiographiques base sur un code Monte Carlo

    Energy Technology Data Exchange (ETDEWEB)

    Rinkel, J.; Dinten, J.M.; Tabary, J

    2004-07-01

    The use of focused anti-scatter grids on digital radiographic systems with two-dimensional detectors produces acquisitions with a decreased scatter to primary ratio and thus improved contrast and resolution. Simulation software is of great interest in optimizing grid configuration according to a specific application. Classical simulators are based on complete detailed geometric descriptions of the grid. They are accurate but very time consuming since they use Monte Carlo code to simulate scatter within the high-frequency grids. We propose a new practical method which couples an analytical simulation of the grid interaction with a radiographic system simulation program. First, a two dimensional matrix of probability depending on the grid is created offline, in which the first dimension represents the angle of impact with respect to the normal to the grid lines and the other the energy of the photon. This matrix of probability is then used by the Monte Carlo simulation software in order to provide the final scattered flux image. To evaluate the gain of CPU time, we define the increasing factor as the increase of CPU time of the simulation with as opposed to without the grid. Increasing factors were calculated with the new model and with classical methods representing the grid with its CAD model as part of the object. With the new method, increasing factors are shorter by one to two orders of magnitude compared with the second one. These results were obtained with a difference in calculated scatter of less than five percent between the new and the classical method. (authors)

  14. Consys Linear Control System Design Software Package

    International Nuclear Information System (INIS)

    Diamantidis, Z.

    1987-01-01

    This package is created in order to help engineers, researchers, students and all who work on linear control systems. The software includes all time and frequency domain analysises, spectral analysises and networks, active filters and regulators design aids. The programmes are written on Hewlett Packard computer in Basic 4.0

  15. Software for Intelligent System Health Management (ISHM)

    Science.gov (United States)

    Trevino, Luis C.

    2004-01-01

    The slide presentation is a briefing in four areas: overview of health management paradigms; overview of the ARC-Houston Software Engineering Technology Workshop held on April 20-22, 2004; identified technologies relevant to technical themes of intelligent system health management; and the author's thoughts on these topics.

  16. Software system for reducing PAM-2 data

    Science.gov (United States)

    Pepin, T. J.

    1982-01-01

    A software system for reducing PAM-II data was constructed. The data reduction process concatenates data tapes; determines ephemeris; and inverts full sun extinction data. Tests of this data reduction process show that PAM-II data can be compared with data from other, similar satellites.

  17. Hotel software-comprehensive hotel systems

    OpenAIRE

    Šilhová, Lenka

    2010-01-01

    This bachelor's thesis deals with the usage of computer systems in the hotel industry. First part is focused on history, development and integration of technology into this field. Second part is dedicated to concrete products of the company Micros-Fidelio, which is the leader of hotel software market in the Czech Republic.

  18. Surgical model-view-controller simulation software framework for local and collaborative applications.

    Science.gov (United States)

    Maciel, Anderson; Sankaranarayanan, Ganesh; Halic, Tansel; Arikatla, Venkata Sreekanth; Lu, Zhonghua; De, Suvranu

    2011-07-01

    Surgical simulations require haptic interactions and collaboration in a shared virtual environment. A software framework for decoupled surgical simulation based on a multi-controller and multi-viewer model-view-controller (MVC) pattern was developed and tested. A software framework for multimodal virtual environments was designed, supporting both visual interactions and haptic feedback while providing developers with an integration tool for heterogeneous architectures maintaining high performance, simplicity of implementation, and straightforward extension. The framework uses decoupled simulation with updates of over 1,000 Hz for haptics and accommodates networked simulation with delays of over 1,000 ms without performance penalty. The simulation software framework was implemented and was used to support the design of virtual reality-based surgery simulation systems. The framework supports the high level of complexity of such applications and the fast response required for interaction with haptics. The efficacy of the framework was tested by implementation of a minimally invasive surgery simulator. A decoupled simulation approach can be implemented as a framework to handle simultaneous processes of the system at the various frame rates each process requires. The framework was successfully used to develop collaborative virtual environments (VEs) involving geographically distributed users connected through a network, with the results comparable to VEs for local users.

  19. 基于直流调速和实时组态的风力机模拟器设计%Design of Wind Turbine Simulator Based on DC Speed Control System and Real-Time Configuration Software

    Institute of Scientific and Technical Information of China (English)

    张计科; 王生铁; 刘广忱

    2013-01-01

    In order to meet the requirements of research on small-scale wind power generation system and improve reliability and development efficiency of software and hardware, the wind turbine simulator based on DC speed control system and real-time configuration environment was designed and implemented according to principle of standardized hardware and configurable software,and experiments were also done in this paper. Experimental results show that the wind turbine simulator not only can simulate accurately static output characteristics of a wind turbine and have good dynamic response so' as to behave almost the same as an actual wind turbine, but also can be configured and run to simulate off-line and run in realtime in MATLAB/Simulink environment,and has the merits of convenient model and parameters adjustment of wind turbine and wind speed as well as high software development efficiency. The wind turbine simulator presented in this paper has significant value for investigation on small wind power generation in a laboratory.%从研究小型风力发电系统需求出发,为了提高软硬件开发效率及可靠性,本着硬件标准化和软件组态化的原则,设计并实现了基于直流调速系统和实时组态环境的小型风力机模拟器,并进行了实验验证.实验结果表明,该风力机模拟器不但可以较为精准地模拟风力机的静态输出特性,动态响应好,达到不依赖于自然风资源而具有实际风力机特性的模拟效果,而且可以使离线仿真和在线运行统一在MATLAB/Simulink平台下组态和运行,风力机和风速模型及参数调整方便、软件开发效率高,对于实验室研究小型风力发电具有重要价值.

  20. Reliable Software Development for Machine Protection Systems

    CERN Document Server

    Anderson, D; Dragu, M; Fuchsberger, K; Garnier, JC; Gorzawski, AA; Koza, M; Krol, K; Misiowiec, K; Stamos, K; Zerlauth, M

    2014-01-01

    The Controls software for the Large Hadron Collider (LHC) at CERN, with more than 150 millions lines of code, resides amongst the largest known code bases in the world1. Industry has been applying Agile software engineering techniques for more than two decades now, and the advantages of these techniques can no longer be ignored to manage the code base for large projects within the accelerator community. Furthermore, CERN is a particular environment due to the high personnel turnover and manpower limitations, where applying Agile processes can improve both, the codebase management as well as its quality. This paper presents the successful application of the Agile software development process Scrum for machine protection systems at CERN, the quality standards and infrastructure introduced together with the Agile process as well as the challenges encountered to adapt it to the CERN environment.

  1. Software challenges in extreme scale systems

    International Nuclear Information System (INIS)

    Sarkar, Vivek; Harrod, William; Snavely, Allan E

    2009-01-01

    Computer systems anticipated in the 2015 - 2020 timeframe are referred to as Extreme Scale because they will be built using massive multi-core processors with 100's of cores per chip. The largest capability Extreme Scale system is expected to deliver Exascale performance of the order of 10 18 operations per second. These systems pose new critical challenges for software in the areas of concurrency, energy efficiency and resiliency. In this paper, we discuss the implications of the concurrency and energy efficiency challenges on future software for Extreme Scale Systems. From an application viewpoint, the concurrency and energy challenges boil down to the ability to express and manage parallelism and locality by exploring a range of strong scaling and new-era weak scaling techniques. For expressing parallelism and locality, the key challenges are the ability to expose all of the intrinsic parallelism and locality in a programming model, while ensuring that this expression of parallelism and locality is portable across a range of systems. For managing parallelism and locality, the OS-related challenges include parallel scalability, spatial partitioning of OS and application functionality, direct hardware access for inter-processor communication, and asynchronous rather than interrupt-driven events, which are accompanied by runtime system challenges for scheduling, synchronization, memory management, communication, performance monitoring, and power management. We conclude by discussing the importance of software-hardware co-design in addressing the fundamental challenges for application enablement on Extreme Scale systems.

  2. A flexible software architecture for tokamak discharge control systems

    International Nuclear Information System (INIS)

    Ferron, J.R.; Penaflor, B.; Walker, M.L.; Moller, J.; Butner, D.

    1995-01-01

    The software structure of the plasma control system in use on the DIII-D tokamak experiment is described. This system implements control functions through software executing in real time on one or more digital computers. The software is organized into a hierarchy that allows new control functions needed to support the DIII-D experimental program to be added easily without affecting previously implemented functions. This also allows the software to be portable in order to create control systems for other applications. The tokamak operator uses an X-windows based interface to specify the time evolution of a tokamak discharge. The interface provides a high level view for the operator that reduces the need for detailed knowledge of the control system operation. There is provision for an asynchronous change to an alternate discharge time evolution in response to an event that is detected in real time. Quality control is enhanced through off-line testing that can make use of software-based tokamak simulators

  3. Smart systems integration and simulation

    CERN Document Server

    Poncino, Massimo; Pravadelli, Graziano

    2016-01-01

    This book-presents new methods and tools for the integration and simulation of smart devices. The design approach described in this book explicitly accounts for integration of Smart Systems components and subsystems as a specific constraint. It includes methodologies and EDA tools to enable multi-disciplinary and multi-scale modeling and design, simulation of multi-domain systems, subsystems and components at all levels of abstraction, system integration and exploration for optimization of functional and non-functional metrics. By covering theoretical and practical aspects of smart device design, this book targets people who are working and studying on hardware/software modelling, component integration and simulation under different positions (system integrators, designers, developers, researchers, teachers, students etc.). In particular, it is a good introduction to people who have interest in managing heterogeneous components in an efficient and effective way on different domains and different abstraction l...

  4. Model for Simulating a Spiral Software-Development Process

    Science.gov (United States)

    Mizell, Carolyn; Curley, Charles; Nayak, Umanath

    2010-01-01

    A discrete-event simulation model, and a computer program that implements the model, have been developed as means of analyzing a spiral software-development process. This model can be tailored to specific development environments for use by software project managers in making quantitative cases for deciding among different software-development processes, courses of action, and cost estimates. A spiral process can be contrasted with a waterfall process, which is a traditional process that consists of a sequence of activities that include analysis of requirements, design, coding, testing, and support. A spiral process is an iterative process that can be regarded as a repeating modified waterfall process. Each iteration includes assessment of risk, analysis of requirements, design, coding, testing, delivery, and evaluation. A key difference between a spiral and a waterfall process is that a spiral process can accommodate changes in requirements at each iteration, whereas in a waterfall process, requirements are considered to be fixed from the beginning and, therefore, a waterfall process is not flexible enough for some projects, especially those in which requirements are not known at the beginning or may change during development. For a given project, a spiral process may cost more and take more time than does a waterfall process, but may better satisfy a customer's expectations and needs. Models for simulating various waterfall processes have been developed previously, but until now, there have been no models for simulating spiral processes. The present spiral-process-simulating model and the software that implements it were developed by extending a discrete-event simulation process model of the IEEE 12207 Software Development Process, which was built using commercially available software known as the Process Analysis Tradeoff Tool (PATT). Typical inputs to PATT models include industry-average values of product size (expressed as number of lines of code

  5. Total Cost of Ownership, System Acceptance and Perceived Success of Enterprise Resource Planning Software: Simulating a Dynamic Feedback Perspective of ERP in the Higher Education Environment

    Science.gov (United States)

    Fryling, Meg

    2010-01-01

    Enterprise Research Planning (ERP) software is advertised as the product that will "run the enterprise", improving data access and accuracy as well as enhancing business process efficiency. Unfortunately, organizations often make implementation decisions with little consideration for the maintenance phase of an ERP, resulting in significant…

  6. Claire, a tool used for the simulation of events in software tests

    International Nuclear Information System (INIS)

    Henry, J.Y.; Boulc'h, J.; Raguideau, J.; Schoen, D.

    1994-06-01

    CLAIRE provides a purely software system which makes it possible to validate the on line applications dealt out to the specifications domain or the code. This tool offers easy graphic design of the application and of its environment. It caries out quite efficiently the simulation of any logged in model and runs the control of the evolution either dynamically or with prerecorded time. (TEC)

  7. Conceptualization and software development of a simulation environment for probalistic safety assessment of radioactive waste repositories

    Energy Technology Data Exchange (ETDEWEB)

    Ghofrani, Javad

    2016-05-26

    Uncertainty and sensitivity analysis of complex simulation models are prominent issues, both in scientific research and education. ReSUS (Repository Simulation, Uncertainty propagation and Sensitivity analysis) is an integrated platform to perform such analysis with numerical models that simulate the THMC (Thermal Hydraulical Mechanical and Chemical) coupled processes via different programs, in particular in the context of safety assessments for radioactive waste repositories. This thesis presents the idea behind the software platform ReSUS and its working mechanisms. Apart from the idea and the working mechanisms, the thesis describes applications related to the safety assessment of radioactive waste disposal systems. In this thesis, previous simulation tools (including the preceding version of ReSUS) are analyzed in order to provide a comprehensive view of the state of the art. In comparison to this state, a more sophisticated software tool is developed here, which provides features which are not offered by previous simulation tools. To achieve this objective, the software platform ReSUS provides a framework for handling probabilistic data uncertainties using deterministic external simulation tools, thus enhancing uncertainty and sensitivity analysis. This platform performs probabilistic simulations of various models, in particular THMC coupled processes, using stand-alone deterministic simulation software tools. The complete software development process of the ReSUS Platform is discussed in this thesis. ReSUS components are developed as libraries, which are capable of being linked to other code implementations. In addition, ASCII template files are used as means for uncertainty propagation into the input files of deterministic simulation tools. The embedded input sampler and analysis tools allow for sensitivity analysis in several kinds of simulation designs. The novelty of the ReSUS platform consists in the flexibility to assign external stand-alone software

  8. Conceptualization and software development of a simulation environment for probalistic safety assessment of radioactive waste repositories

    International Nuclear Information System (INIS)

    Ghofrani, Javad

    2016-01-01

    Uncertainty and sensitivity analysis of complex simulation models are prominent issues, both in scientific research and education. ReSUS (Repository Simulation, Uncertainty propagation and Sensitivity analysis) is an integrated platform to perform such analysis with numerical models that simulate the THMC (Thermal Hydraulical Mechanical and Chemical) coupled processes via different programs, in particular in the context of safety assessments for radioactive waste repositories. This thesis presents the idea behind the software platform ReSUS and its working mechanisms. Apart from the idea and the working mechanisms, the thesis describes applications related to the safety assessment of radioactive waste disposal systems. In this thesis, previous simulation tools (including the preceding version of ReSUS) are analyzed in order to provide a comprehensive view of the state of the art. In comparison to this state, a more sophisticated software tool is developed here, which provides features which are not offered by previous simulation tools. To achieve this objective, the software platform ReSUS provides a framework for handling probabilistic data uncertainties using deterministic external simulation tools, thus enhancing uncertainty and sensitivity analysis. This platform performs probabilistic simulations of various models, in particular THMC coupled processes, using stand-alone deterministic simulation software tools. The complete software development process of the ReSUS Platform is discussed in this thesis. ReSUS components are developed as libraries, which are capable of being linked to other code implementations. In addition, ASCII template files are used as means for uncertainty propagation into the input files of deterministic simulation tools. The embedded input sampler and analysis tools allow for sensitivity analysis in several kinds of simulation designs. The novelty of the ReSUS platform consists in the flexibility to assign external stand-alone software

  9. Software Defined Common Processing System (SDCPS), Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Coherent Logix, Incorporated proposes the Software Defined Common Processing System (SDCPS) program to facilitate the development of a Software Defined Radio...

  10. A graphical simulation software for instruction in cardiovascular mechanics physiology

    Directory of Open Access Journals (Sweden)

    Wenger Roland H

    2011-01-01

    Full Text Available Abstract Background Computer supported, interactive e-learning systems are widely used in the teaching of physiology. However, the currently available complimentary software tools in the field of the physiology of cardiovascular mechanics have not yet been adapted to the latest systems software. Therefore, a simple-to-use replacement for undergraduate and graduate students' education was needed, including an up-to-date graphical software that is validated and field-tested. Methods Software compatible to Windows, based on modified versions of existing mathematical algorithms, has been newly developed. Testing was performed during a full term of physiological lecturing to medical and biology students. Results The newly developed CLabUZH software models a reduced human cardiovascular loop containing all basic compartments: an isolated heart including an artificial electrical stimulator, main vessels and the peripheral resistive components. Students can alter several physiological parameters interactively. The resulting output variables are printed in x-y diagrams and in addition shown in an animated, graphical model. CLabUZH offers insight into the relations of volume, pressure and time dependency in the circulation and their correlation to the electrocardiogram (ECG. Established mechanisms such as the Frank-Starling Law or the Windkessel Effect are considered in this model. The CLabUZH software is self-contained with no extra installation required and runs on most of today's personal computer systems. Conclusions CLabUZH is a user-friendly interactive computer programme that has proved to be useful in teaching the basic physiological principles of heart mechanics.

  11. Design and implementation of a software tool intended for simulation and test of real time codes

    International Nuclear Information System (INIS)

    Le Louarn, C.

    1986-09-01

    The objective of real time software testing is to show off processing errors and unobserved functional requirements or timing constraints in a code. In the perspective of safety analysis of nuclear equipments of power plants testing should be carried independently from the physical process (which is not generally available), and because casual hardware failures must be considered. We propose here a simulation and test tool, integrally software, with large interactive possibilities for testing assembly code running on microprocessor. The OST (outil d'aide a la simulation et au Test de logiciels temps reel) simulates code execution and hardware or software environment behaviour. Test execution is closely monitored and many useful informations are automatically saved. The present thesis work details, after exposing methods and tools dedicated to real time software, the OST system. We show the internal mechanisms and objects of the system: particularly ''events'' (which describe evolutions of the system under test) and mnemonics (which describe the variables). Then, we detail the interactive means available to the user for constructing the test data and the environment of the tested software. Finally, a prototype implementation is presented along with the results of the tests carried out. This demonstrates the many advantages of the use of an automatic tool over a manual investigation. As a conclusion, further developments, nececessary to complete the final tool are rewieved [fr

  12. Automated software for hydraulic simulation of pipeline operation

    Directory of Open Access Journals (Sweden)

    Hurgin Roman

    2018-01-01

    Full Text Available Design of modern water supply systems of large cities as well as their management via renovation of hydraulic models poses time-consuming tasks to researchers, and coping with this task requires specific approaches. When tackling these tasks, water services companies come across a lot of information about various objects of water infrastructure, the majority of which is located underground. In those cases, modern computer-aided design systems containing various components come to help. These systems help to solve a wide array of problems using existing information regarding pipelines, analysis and optimization of their basic parameters. CAD software is becoming an integral part of water supply systems management in large cities, and its capabilities allow engineering and operating companies to not only collect all the necessary data concerning water supply systems in any given city, but also to conduct research aimed at improving various parameters of these systems, including optimization of their hydraulic properties which directly determine the quality of water. This paper contains the analysis of automated CAD software for hydraulic design and management of city water supply systems in order to provide safe and efficient operation of these water supply systems. Authors select the most suitable software that might be used to provide hydraulic compatibility of old and new sections of water supply ring mains after selective or continuous draw-in renovation and decrease in diameter of distribution networks against the background of water consumption decrease in the cities.

  13. Quench Simulation of Superconducting Magnets with Commercial Multiphysics Software

    CERN Document Server

    AUTHOR|(SzGeCERN)751171; Auchmann, Bernhard; Jarkko, Niiranen; Maciejewski, Michal

    The simulation of quenches in superconducting magnets is a multiphysics problem of highest complexity. Operated at 1.9 K above absolute zero, the material properties of superconductors and superfluid helium vary by several orders of magnitude over a range of only 10 K. The heat transfer from metal to helium goes through different transfer and boiling regimes as a function of temperature, heat flux, and transferred energy. Electrical, magnetic, thermal, and fluid dynamic effects are intimately coupled, yet live on vastly different time and spatial scales. While the physical models may be the same in all cases, it is an open debate whether the user should opt for commercial multiphysics software like ANSYS or COMSOL, write customized models based on general purpose network solvers like SPICE, or implement the physics models and numerical solvers entirely in custom software like the QP3, THEA, and ROXIE codes currently in use at the European Organisation for Nuclear Research (CERN). Each approach has its strengt...

  14. Architecture of a software quench management system

    International Nuclear Information System (INIS)

    Jerzy M. Nogiec et al.

    2001-01-01

    Testing superconducting accelerator magnets is inherently coupled with the proper handling of quenches; i.e., protecting the magnet and characterizing the quench process. Therefore, software implementations must include elements of both data acquisition and real-time controls. The architecture of the quench management software developed at Fermilab's Magnet Test Facility is described. This system consists of quench detection, quench protection, and quench characterization components that execute concurrently in a distributed system. Collaboration between the elements of quench detection, quench characterization and current control are discussed, together with a schema of distributed saving of various quench-related data. Solutions to synchronization and reliability in such a distributed quench system are also presented

  15. Timing system control software in the SLC

    International Nuclear Information System (INIS)

    Thompson, K.; Phinney, N.

    1985-04-01

    A new timing system that allows precision (approx.1 to 2 ns) control of the trigger times of klystrons, beam position monitors, and other devices on a pulse-to-pulse basis at up to 360 Hz is in operation in the first third of the SLAC linear accelerator. The control software is divided between a central host VAX and local Intel 8086-based microprocessor clusters. Facilities exist to set up and adjust the timing of devices or groups of devices independently for beam pulses having different destinations and purposes, which are run in an interlaced fashion during normal machine operation. Upgrading of the system is currently underway, using a new version of the Programmable Delay Unit CAMAC module to allow pipelining of timing information for three machine pulses. An overview of the current state of the system is presented in this paper, with an emphasis on software control

  16. An interactive beam position monitor system simulator

    International Nuclear Information System (INIS)

    Ryan, W.A.; Shea, T.J.

    1993-03-01

    A system simulator has been implemented to aid the development of the RHIC position monitor system. Based on the LabVIEW software package by National Instruments, this simulator allows engineers and technicians to interactively explore the parameter space of a system during the design phase. Adjustable parameters are divided into three categories: beam, pickup, and electronics. The simulator uses these parameters in simple formulas to produce results in both time-domain and frequencydomain. During the prototyping phase, these simulated results can be compared to test data acquired with the same software package. The RHIC position monitor system is presented as an example, but the software is applicable to several other systems as well

  17. Integrating open-source software applications to build molecular dynamics systems.

    Science.gov (United States)

    Allen, Bruce M; Predecki, Paul K; Kumosa, Maciej

    2014-04-05

    Three open-source applications, NanoEngineer-1, packmol, and mis2lmp are integrated using an open-source file format to quickly create molecular dynamics (MD) cells for simulation. The three software applications collectively make up the open-source software (OSS) suite known as MD Studio (MDS). The software is validated through software engineering practices and is verified through simulation of the diglycidyl ether of bisphenol-a and isophorone diamine (DGEBA/IPD) system. Multiple simulations are run using the MDS software to create MD cells, and the data generated are used to calculate density, bulk modulus, and glass transition temperature of the DGEBA/IPD system. Simulation results compare well with published experimental and numerical results. The MDS software prototype confirms that OSS applications can be analyzed against real-world research requirements and integrated to create a new capability. Copyright © 2014 Wiley Periodicals, Inc.

  18. Improvements to information management systems simulator

    Science.gov (United States)

    Bilek, R. W.

    1972-01-01

    The performance of personnel in the augmentation and improvement of the interactive IMSIM information management simulation model is summarized. With this augmented model, NASA now has even greater capabilities for the simulation of computer system configurations, data processing loads imposed on these configurations, and executive software to control system operations. Through these simulations, NASA has an extremely cost effective capability for the design and analysis of computer-based data management systems.

  19. Simulation Assessment Validation Environment (SAVE). Software User’s Manual

    Science.gov (United States)

    2000-09-01

    TOOL USAGE Figure 2-14: Factory Simulation Tool Usage This tool directly emulates real-world system behaviors that are associated with each resource...manufacturing simulation tools and Computer Aided Design (CAD) tools. The Factory/Schedule Simulation tool is used to simulate real-world system behaviors ...char Name>_pfchar Part Usage(Produced)/Part/Feature/Char <partuseName>_<partName>_<matName>_<char Name>_cmat PartUsage( Comsumed )/Part/Material

  20. Assembly Line Efficiency Improvement by Using WITNESS Simulation Software

    Science.gov (United States)

    Yasir, A. S. H. M.; Mohamed, N. M. Z. N.

    2018-03-01

    In the nowadays-competitive world, efficiencies and the productivity of the assembly line are essential in manufacturing company. This paper demonstrates the study of the existing production line performance. The actual cycle time observed and recorded during the working process. The current layout was designed and analysed using Witness simulation software. The productivity and effectiveness for every single operator are measured to determine the operator idle time and busy time. Two new alternatives layout were proposed and analysed by using Witness simulation software to improve the performance of production activities. This research provided valuable and better understanding of production effectiveness by adjusting the line balancing. After analysing the data, simulation result from the current layout and the proposed plan later been tabulated to compare the improved efficiency and productivity. The proposed design plan has shown an increase in yield and productivity compared to the current arrangement. This research has been carried out in company XYZ, which is one of the automotive premises in Pahang, Malaysia.

  1. A software Event Summation System for MDSplus

    International Nuclear Information System (INIS)

    Davis, W.M.; Mastrovito, D.M.; Roney, P.G.; Sichta, P.

    2008-01-01

    The MDSplus data acquisition and management system uses software events for communication among interdependent processes anywhere on the network. Actions can then be triggered, such as a data-acquisition routine, or analysis or display programs waiting for data. A small amount of data, such as a shot number, can be passed with these events. Since programs sometimes need more than one data set, we developed a system on NSTX to declare composite events using logical AND and OR operations. The system is written in the IDL language, so it can be run on Linux, Macintosh or Windows platforms. Like MDSplus, the Experimental Physics and Industrial Control System (EPICS) is a core component of the NSTX software environment. The Event Summation System provides an IDL-based interface to EPICS. This permits EPICS-aware processes to be synchronized with MDSplus-aware processes, to provide, for example, engineering operators information about physics data acquisition and analysis. Reliability was a more important design consideration than performance for this system; the system's architecture includes features to support this. The system has run for weeks at a time without requiring manual intervention. Hundreds of incoming events per second can be handled reliably. All incoming and declared events are logged with a timestamp. The system can be configured easily through a single, easy-to-read text file

  2. Software quality assurance and software safety in the Biomed Control System

    International Nuclear Information System (INIS)

    Singh, R.P.; Chu, W.T.; Ludewigt, B.A.; Marks, K.M.; Nyman, M.A.; Renner, T.R.; Stradtner, R.

    1989-01-01

    The Biomed Control System is a hardware/software system used for the delivery, measurement and monitoring of heavy-ion beams in the patient treatment and biology experiment rooms in the Bevalac at the Lawrence Berkeley Laboratory (LBL). This paper describes some aspects of this system including historical background philosophy, configuration management, hardware features that facilitate software testing, software testing procedures, the release of new software quality assurance, safety and operator monitoring. 3 refs

  3. Modular, Autonomous Command and Data Handling Software with Built-In Simulation and Test

    Science.gov (United States)

    Cuseo, John

    2012-01-01

    The spacecraft system that plays the greatest role throughout the program lifecycle is the Command and Data Handling System (C&DH), along with the associated algorithms and software. The C&DH takes on this role as cost driver because it is the brains of the spacecraft and is the element of the system that is primarily responsible for the integration and interoperability of all spacecraft subsystems. During design and development, many activities associated with mission design, system engineering, and subsystem development result in products that are directly supported by the C&DH, such as interfaces, algorithms, flight software (FSW), and parameter sets. A modular system architecture has been developed that provides a means for rapid spacecraft assembly, test, and integration. This modular C&DH software architecture, which can be targeted and adapted to a wide variety of spacecraft architectures, payloads, and mission requirements, eliminates the current practice of rewriting the spacecraft software and test environment for every mission. This software allows missionspecific software and algorithms to be rapidly integrated and tested, significantly decreasing time involved in the software development cycle. Additionally, the FSW includes an Onboard Dynamic Simulation System (ODySSy) that allows the C&DH software to support rapid integration and test. With this solution, the C&DH software capabilities will encompass all phases of the spacecraft lifecycle. ODySSy is an on-board simulation capability built directly into the FSW that provides dynamic built-in test capabilities as soon as the FSW image is loaded onto the processor. It includes a six-degrees- of-freedom, high-fidelity simulation that allows complete closed-loop and hardware-in-the-loop testing of a spacecraft in a ground processing environment without any additional external stimuli. ODySSy can intercept and modify sensor inputs using mathematical sensor models, and can intercept and respond to actuator

  4. Software for airborne radiation monitoring system

    International Nuclear Information System (INIS)

    Sheinfeld, M.; Kadmon, Y.; Tirosh, D.; Elhanany, I.; Gabovitch, A.; Barak, D.

    1997-01-01

    The Airborne Radiation Monitoring System monitors radioactive contamination in the air or on the ground. The contamination source can be a radioactive plume or an area contaminated with radionuclides. This system is composed of two major parts: Airborne Unit carried by a helicopter, and Ground Station carried by a truck. The Airborne software is intended to be the core of a computerized airborne station. The software is written in C++ under MS-Windows with object-oriented methodology. It has been designed to be user-friendly: function keys and other accelerators are used for vital operations, a help file and help subjects are available, the Human-Machine-Interface is plain and obvious. (authors)

  5. Novel software system development for finance

    OpenAIRE

    Maad, Soha

    2002-01-01

    This paper addresses the need for novel software system development (SSD) practices in finance. It proposes Empirical Modelling as a novel approach for SSD in finance. This approach aims at finding a suitable framework for studying both the traditional and the emerging computing culture to SSD in finance. First, the paper studies the change in the financial industry and identifies key issues of the application of computer-based technology in finance. These key issues are framed in a wider age...

  6. Creating the next generation control system software

    International Nuclear Information System (INIS)

    Schultz, D.E.

    1989-01-01

    A new 1980's style support package for future accelerator control systems is proposed. It provides a way to create accelerator applications software without traditional programming. Visual Interactive Applications (VIA) is designed to meet the needs of expanded accelerator complexes in a more cost effective way than past experience with procedural languages by using technology from the personal computer and artificial intelligence communities. 4 refs

  7. FMI for Co-Simulation of Embedded Control Software

    DEFF Research Database (Denmark)

    Pedersen, Nicolai; Bojsen, Tom; Madsen, Jan

    2016-01-01

    the clock of a real time operating system (RTOS), by overwriting the idle thread and waiting for a signal to start execution until return to idle. This ap-proach ensures a deterministic and temporal execution of the simulation across multiple nodes. As proof of concept, a co-simulation is conducted, showing...

  8. Distributed Sensor Network Software Development Testing through Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Brennan, Sean M. [Univ. of New Mexico, Albuquerque, NM (United States)

    2003-12-01

    The distributed sensor network (DSN) presents a novel and highly complex computing platform with dif culties and opportunities that are just beginning to be explored. The potential of sensor networks extends from monitoring for threat reduction, to conducting instant and remote inventories, to ecological surveys. Developing and testing for robust and scalable applications is currently practiced almost exclusively in hardware. The Distributed Sensors Simulator (DSS) is an infrastructure that allows the user to debug and test software for DSNs independent of hardware constraints. The exibility of DSS allows developers and researchers to investigate topological, phenomenological, networking, robustness and scaling issues, to explore arbitrary algorithms for distributed sensors, and to defeat those algorithms through simulated failure. The user speci es the topology, the environment, the application, and any number of arbitrary failures; DSS provides the virtual environmental embedding.

  9. Software Development Processes Applied to Computational Icing Simulation

    Science.gov (United States)

    Levinson, Laurie H.; Potapezuk, Mark G.; Mellor, Pamela A.

    1999-01-01

    The development of computational icing simulation methods is making the transition form the research to common place use in design and certification efforts. As such, standards of code management, design validation, and documentation must be adjusted to accommodate the increased expectations of the user community with respect to accuracy, reliability, capability, and usability. This paper discusses these concepts with regard to current and future icing simulation code development efforts as implemented by the Icing Branch of the NASA Lewis Research Center in collaboration with the NASA Lewis Engineering Design and Analysis Division. With the application of the techniques outlined in this paper, the LEWICE ice accretion code has become a more stable and reliable software product.

  10. Simulating 60 Co gamma irradiation systems

    International Nuclear Information System (INIS)

    Omi, Nelson M.; Rela, Paulo R.

    2000-01-01

    The use of Cadgamma, a software dedicated to simulate 60 Co gamma irradiation systems, can lead to an optimized process and simulating, in a few hours, many configurations setups for the irradiation elements. The software can also simulate changes in the path of the product and the influence of any steady body like the support of the product support and source shoulders. These simulations minimize the number of dose mapping tests in industrial applications and allow the study of unusual setups. Cadgamma was developed at IPEN to simulate it is multipurpose 60 Co irradiation system, under construction and planned to be operating by the second half of 2001. The software was used on project stage and will help to optimize the irradiation process for each product to be treated. (author)

  11. CT-Based Brachytherapy Treatment Planning using Monte Carlo Simulation Aided by an Interface Software

    Directory of Open Access Journals (Sweden)

    Vahid Moslemi

    2011-03-01

    Full Text Available Introduction: In brachytherapy, radioactive sources are placed close to the tumor, therefore, small changes in their positions can cause large changes in the dose distribution. This emphasizes the need for computerized treatment planning. The usual method for treatment planning of cervix brachytherapy uses conventional radiographs in the Manchester system. Nowadays, because of their advantages in locating the source positions and the surrounding tissues, CT and MRI images are replacing conventional radiographs. In this study, we used CT images in Monte Carlo based dose calculation for brachytherapy treatment planning, using an interface software to create the geometry file required in the MCNP code. The aim of using the interface software is to facilitate and speed up the geometry set-up for simulations based on the patient’s anatomy. This paper examines the feasibility of this method in cervix brachytherapy and assesses its accuracy and speed. Material and Methods: For dosimetric measurements regarding the treatment plan, a pelvic phantom was made from polyethylene in which the treatment applicators could be placed. For simulations using CT images, the phantom was scanned at 120 kVp. Using an interface software written in MATLAB, the CT images were converted into MCNP input file and the simulation was then performed. Results: Using the interface software, preparation time for the simulations of the applicator and surrounding structures was approximately 3 minutes; the corresponding time needed in the conventional MCNP geometry entry being approximately 1 hour. The discrepancy in the simulated and measured doses to point A was 1.7% of the prescribed dose.  The corresponding dose differences between the two methods in rectum and bladder were 3.0% and 3.7% of the prescribed dose, respectively. Comparing the results of simulation using the interface software with those of simulation using the standard MCNP geometry entry showed a less than 1

  12. MATLAB Software Versions and Licenses for the Peregrine System |

    Science.gov (United States)

    High-Performance Computing | NREL MATLAB Software Versions and Licenses for the Peregrine System MATLAB Software Versions and Licenses for the Peregrine System Learn about the MATLAB software Peregrine is R2017b. Licenses MATLAB is proprietary software. As such, users have access to a limited number

  13. Educational software for simulating risk of HIV infection

    Science.gov (United States)

    Rothberg, Madeleine A.; Sandberg, Sonja; Awerbuch, Tamara E.

    1994-03-01

    The AIDS epidemic is still growing rapidly and the disease is thought to be uniformly fatal. With no vaccine or cure in sight, education during high school years is a critical component in the prevention of AIDS. We propose the use of computer software with which high school students can explore via simulation their own risk of acquiring an HIV infection given certain sexual behaviors. This particular software is intended to help students understand the three factors that determine their risk of HIV infection (number of sexual acts, probability that their partners are infected, and riskiness of the specific sexual activities they choose). Users can explicitly calculate their own chances of becoming infected based on decisions they make. Use of the program is expected to personalize the risk of HIV infection and thus increase users' concern and awareness. Behavioral change may not result from increased knowledge alone. Therefore the effectiveness of this program in changing attitudes toward risky sexual behaviors would be enhanced when the simulation is embedded in an appropriate curriculum. A description of the program and an example of its use are presented.

  14. GIS-Based Noise Simulation Open Source Software: N-GNOIS

    Science.gov (United States)

    Vijay, Ritesh; Sharma, A.; Kumar, M.; Shende, V.; Chakrabarti, T.; Gupta, Rajesh

    2015-12-01

    Geographical information system (GIS)-based noise simulation software (N-GNOIS) has been developed to simulate the noise scenario due to point and mobile sources considering the impact of geographical features and meteorological parameters. These have been addressed in the software through attenuation modules of atmosphere, vegetation and barrier. N-GNOIS is a user friendly, platform-independent and open geospatial consortia (OGC) compliant software. It has been developed using open source technology (QGIS) and open source language (Python). N-GNOIS has unique features like cumulative impact of point and mobile sources, building structure and honking due to traffic. Honking is the most common phenomenon in developing countries and is frequently observed on any type of roads. N-GNOIS also helps in designing physical barrier and vegetation cover to check the propagation of noise and acts as a decision making tool for planning and management of noise component in environmental impact assessment (EIA) studies.

  15. Ground test accelerator control system software

    International Nuclear Information System (INIS)

    Burczyk, L.; Dalesio, R.; Dingler, R.; Hill, J.; Howell, J.A.; Kerstiens, D.; King, R.; Kozubal, A.; Little, C.; Martz, V.; Rothrock, R.; Sutton, J.

    1988-01-01

    This paper reports on the GTA control system that provides an environment in which the automation of a state-of-the-art accelerator can be developed. It makes use of commercially available computers, workstations, computer networks, industrial 110 equipment, and software. This system has built-in supervisory control (like most accelerator control systems), tools to support continuous control (like the process control industry), and sequential control for automatic start-up and fault recovery (like few other accelerator control systems). Several software tools support these levels of control: a real-time operating system (VxWorks) with a real-time kernel (VRTX), a configuration database, a sequencer, and a graphics editor. VxWorks supports multitasking, fast context-switching, and preemptive scheduling. VxWorks/VRTX is a network-based development environment specifically designed to work in partnership with the UNIX operating system. A data base provides the interface to the accelerator components. It consists of a run time library and a database configuration and editing tool. A sequencer initiates and controls the operation of all sequence programs (expressed as state programs). A graphics editor gives the user the ability to create color graphic displays showing the state of the machine in either text or graphics form

  16. Application software for new BEPC interlock system

    International Nuclear Information System (INIS)

    Tang Shuming; Na Xiangyin; Chen Jiansong; Yu Yulan

    1997-01-01

    New BEPC (Beijing electron Positron collider) interlock system has been built in order to improve the reliability of personnel safety and interlock functions. Moreover, the system updates BEPC operation message once every 6 seconds, which are displayed on TV screens at the major entrances. Since March of 1996, new BEPC interlock system has been operating reliably. The hardware of the system is based on Programmable Logic Controllers (PLC). A multimedia IBM/PC-586 as the host computer of the PLCs, monitors the PLC system via serial port COM2. The PC communicates with the central computer VAX-4500 of BEPC control system and gets operating massage of the accelerator through serial port COM3. The application software on the host computer has been developed. Visual C++ for MS-Windows 3.2 TM is selected as the work bench. It provides nice tools for building programs, such as APP STUDIO, CLASS WIZARD, APP WIZARD and debugger tool. The author describes the design idea and the structure of the application software. Error tolerance is taken into consideration. The author also presents a small database and its data structure for the application

  17. Integrating existing software toolkits into VO system

    Science.gov (United States)

    Cui, Chenzhou; Zhao, Yong-Heng; Wang, Xiaoqian; Sang, Jian; Luo, Ze

    2004-09-01

    Virtual Observatory (VO) is a collection of interoperating data archives and software tools. Taking advantages of the latest information technologies, it aims to provide a data-intensively online research environment for astronomers all around the world. A large number of high-qualified astronomical software packages and libraries are powerful and easy of use, and have been widely used by astronomers for many years. Integrating those toolkits into the VO system is a necessary and important task for the VO developers. VO architecture greatly depends on Grid and Web services, consequently the general VO integration route is "Java Ready - Grid Ready - VO Ready". In the paper, we discuss the importance of VO integration for existing toolkits and discuss the possible solutions. We introduce two efforts in the field from China-VO project, "gImageMagick" and "Galactic abundance gradients statistical research under grid environment". We also discuss what additional work should be done to convert Grid service to VO service.

  18. Software Engineering and Swarm-Based Systems

    Science.gov (United States)

    Hinchey, Michael G.; Sterritt, Roy; Pena, Joaquin; Rouff, Christopher A.

    2006-01-01

    We discuss two software engineering aspects in the development of complex swarm-based systems. NASA researchers have been investigating various possible concept missions that would greatly advance future space exploration capabilities. The concept mission that we have focused on exploits the principles of autonomic computing as well as being based on the use of intelligent swarms, whereby a (potentially large) number of similar spacecraft collaborate to achieve mission goals. The intent is that such systems not only can be sent to explore remote and harsh environments but also are endowed with greater degrees of protection and longevity to achieve mission goals.

  19. The VAXONLINE software system at Fermilab

    International Nuclear Information System (INIS)

    White, V.; Heinicke, P.; Berman, E.

    1987-06-01

    The VAXONLINE software system, started in late 1984, is now in use at 12 experiments at Fermilab, with at least one VAX or MicroVax. Data acquisition features now provide for the collection and combination of data from one or more sources, via a list-driven Event Builder program. Supported sources include CAMAC, FASTBUS, Front-end PDP-11's, Disk, Tape, DECnet, and other processors running VAXONLINE. This paper describes the functionality provided by the VAXONLINE system, gives performance figures, and discusses the ongoing program of enhancements

  20. Digital PIV (DPIV) Software Analysis System

    Science.gov (United States)

    Blackshire, James L.

    1997-01-01

    A software package was developed to provide a Digital PIV (DPIV) capability for NASA LaRC. The system provides an automated image capture, test correlation, and autocorrelation analysis capability for the Kodak Megaplus 1.4 digital camera system for PIV measurements. The package includes three separate programs that, when used together with the PIV data validation algorithm, constitutes a complete DPIV analysis capability. The programs are run on an IBM PC/AT host computer running either Microsoft Windows 3.1 or Windows 95 using a 'quickwin' format that allows simple user interface and output capabilities to the windows environment.

  1. The architecture of a reliable software monitoring system for embedded software systems

    International Nuclear Information System (INIS)

    Munson, J.; Krings, A.; Hiromoto, R.

    2006-01-01

    We develop the notion of a measurement-based methodology for embedded software systems to ensure properties of reliability, survivability and security, not only under benign faults but under malicious and hazardous conditions as well. The driving force is the need to develop a dynamic run-time monitoring system for use in these embedded mission critical systems. These systems must run reliably, must be secure and they must fail gracefully. That is, they must continue operating in the face of the departures from their nominal operating scenarios, the failure of one or more system components due to normal hardware and software faults, as well as malicious acts. To insure the integrity of embedded software systems, the activity of these systems must be monitored as they operate. For each of these systems, it is possible to establish a very succinct representation of nominal system activity. Furthermore, it is possible to detect departures from the nominal operating scenario in a timely fashion. Such departure may be due to various circumstances, e.g., an assault from an outside agent, thus forcing the system to operate in an off-nominal environment for which it was neither tested nor certified, or a hardware/software component that has ceased to operate in a nominal fashion. A well-designed system will have the property of graceful degradation. It must continue to run even though some of the functionality may have been lost. This involves the intelligent re-mapping of system functions. Those functions that are impacted by the failure of a system component must be identified and isolated. Thus, a system must be designed so that its basic operations may be re-mapped onto system components still operational. That is, the mission objectives of the software must be reassessed in terms of the current operational capabilities of the software system. By integrating the mechanisms to support observation and detection directly into the design methodology, we propose to shift

  2. Monte Carlo simulation with the Gate software using grid computing

    International Nuclear Information System (INIS)

    Reuillon, R.; Hill, D.R.C.; Gouinaud, C.; El Bitar, Z.; Breton, V.; Buvat, I.

    2009-03-01

    Monte Carlo simulations are widely used in emission tomography, for protocol optimization, design of processing or data analysis methods, tomographic reconstruction, or tomograph design optimization. Monte Carlo simulations needing many replicates to obtain good statistical results can be easily executed in parallel using the 'Multiple Replications In Parallel' approach. However, several precautions have to be taken in the generation of the parallel streams of pseudo-random numbers. In this paper, we present the distribution of Monte Carlo simulations performed with the GATE software using local clusters and grid computing. We obtained very convincing results with this large medical application, thanks to the EGEE Grid (Enabling Grid for E-science), achieving in one week computations that could have taken more than 3 years of processing on a single computer. This work has been achieved thanks to a generic object-oriented toolbox called DistMe which we designed to automate this kind of parallelization for Monte Carlo simulations. This toolbox, written in Java is freely available on SourceForge and helped to ensure a rigorous distribution of pseudo-random number streams. It is based on the use of a documented XML format for random numbers generators statuses. (authors)

  3. Model extension and improvement for simulator-based software safety analysis

    Energy Technology Data Exchange (ETDEWEB)

    Huang, H.-W. [Department of Engineering and System Science, National Tsing Hua University (NTHU), 101 Section 2 Kuang Fu Road, Hsinchu, Taiwan (China) and Institute of Nuclear Energy Research (INER), No. 1000 Wenhua Road, Chiaan Village, Longtan Township, Taoyuan County 32546, Taiwan (China)]. E-mail: hwhwang@iner.gov.tw; Shih Chunkuan [Department of Engineering and System Science, National Tsing Hua University (NTHU), 101 Section 2 Kuang Fu Road, Hsinchu, Taiwan (China); Yih Swu [Department of Computer Science and Information Engineering, Ching Yun University, 229 Chien-Hsin Road, Jung-Li, Taoyuan County 320, Taiwan (China); Chen, M.-H. [Institute of Nuclear Energy Research (INER), No. 1000Wenhua Road, Chiaan Village, Longtan Township, Taoyuan County 32546, Taiwan (China); Lin, J.-M. [Taiwan Power Company (TPC), 242 Roosevelt Road, Section 3, Taipei 100, Taiwan (China)

    2007-05-15

    One of the major concerns when employing digital I and C system in nuclear power plant is digital system may introduce new failure mode, which differs with previous analog I and C system. Various techniques are under developing to analyze the hazard originated from software faults in digital systems. Preliminary hazard analysis, failure modes and effects analysis, and fault tree analysis are the most extensive used techniques. However, these techniques are static analysis methods, cannot perform dynamic analysis and the interactions among systems. This research utilizes 'simulator/plant model testing' technique classified in (IEEE Std 7-4.3.2-2003, 2003. IEEE Standard for Digital Computers in Safety Systems of Nuclear Power Generating Stations) to identify hazards which might be induced by nuclear I and C software defects. The recirculation flow system, control rod system, feedwater system, steam line model, dynamic power-core flow map, and related control systems of PCTran-ABWR model were successfully extended and improved. The benchmark against ABWR SAR proves this modified model is capable to accomplish dynamic system level software safety analysis and better than the static methods. This improved plant simulation can then further be applied to hazard analysis for operator/digital I and C interface interaction failure study, and the hardware-in-the-loop fault injection study.

  4. Resilience Engineering in Critical Long Term Aerospace Software Systems: A New Approach to Spacecraft Software Safety

    Science.gov (United States)

    Dulo, D. A.

    Safety critical software systems permeate spacecraft, and in a long term venture like a starship would be pervasive in every system of the spacecraft. Yet software failure today continues to plague both the systems and the organizations that develop them resulting in the loss of life, time, money, and valuable system platforms. A starship cannot afford this type of software failure in long journeys away from home. A single software failure could have catastrophic results for the spaceship and the crew onboard. This paper will offer a new approach to developing safe reliable software systems through focusing not on the traditional safety/reliability engineering paradigms but rather by focusing on a new paradigm: Resilience and Failure Obviation Engineering. The foremost objective of this approach is the obviation of failure, coupled with the ability of a software system to prevent or adapt to complex changing conditions in real time as a safety valve should failure occur to ensure safe system continuity. Through this approach, safety is ensured through foresight to anticipate failure and to adapt to risk in real time before failure occurs. In a starship, this type of software engineering is vital. Through software developed in a resilient manner, a starship would have reduced or eliminated software failure, and would have the ability to rapidly adapt should a software system become unstable or unsafe. As a result, long term software safety, reliability, and resilience would be present for a successful long term starship mission.

  5. A federated design for a neurobiological simulation engine: the CBI federated software architecture.

    Directory of Open Access Journals (Sweden)

    Hugo Cornelis

    Full Text Available Simulator interoperability and extensibility has become a growing requirement in computational biology. To address this, we have developed a federated software architecture. It is federated by its union of independent disparate systems under a single cohesive view, provides interoperability through its capability to communicate, execute programs, or transfer data among different independent applications, and supports extensibility by enabling simulator expansion or enhancement without the need for major changes to system infrastructure. Historically, simulator interoperability has relied on development of declarative markup languages such as the neuron modeling language NeuroML, while simulator extension typically occurred through modification of existing functionality. The software architecture we describe here allows for both these approaches. However, it is designed to support alternative paradigms of interoperability and extensibility through the provision of logical relationships and defined application programming interfaces. They allow any appropriately configured component or software application to be incorporated into a simulator. The architecture defines independent functional modules that run stand-alone. They are arranged in logical layers that naturally correspond to the occurrence of high-level data (biological concepts versus low-level data (numerical values and distinguish data from control functions. The modular nature of the architecture and its independence from a given technology facilitates communication about similar concepts and functions for both users and developers. It provides several advantages for multiple independent contributions to software development. Importantly, these include: (1 Reduction in complexity of individual simulator components when compared to the complexity of a complete simulator, (2 Documentation of individual components in terms of their inputs and outputs, (3 Easy removal or replacement of

  6. Data acquisition and test system software

    International Nuclear Information System (INIS)

    Bourgeois, N.A. Jr.

    1979-03-01

    Sandia Laboratories has been assigned the task by the Base and Installation Security Systems (BISS) Program Office to develop various aspects of perimeter security systems. One part of this effort involves the development of advanced signal processing techniques to reduce the false and nuisance alarms from sensor systems while improving the probability of intrusion detection. The need existed for both data acquisition hardware and software. Also, the hardware is used to implement and test the signal processing algorithms in real time. The hardware developed for this signal processing task is the Data Acquisition and Test System (DATS). The programs developed for use on DATS are described. The descriptions are taken directly from the documentation included within the source programs themselves

  7. Software Design Methods for Real-Time Systems

    Science.gov (United States)

    1989-12-01

    This module describes the concepts and methods used in the software design of real time systems . It outlines the characteristics of real time systems , describes...the role of software design in real time system development, surveys and compares some software design methods for real - time systems , and

  8. 14 CFR 417.123 - Computing systems and software.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Computing systems and software. 417.123... systems and software. (a) A launch operator must document a system safety process that identifies the... systems and software. (b) A launch operator must identify all safety-critical functions associated with...

  9. Cloud-Based SimJavaWeb Software Tool to Learn Simulation

    Directory of Open Access Journals (Sweden)

    A. Yu. Bykov

    2017-01-01

    Full Text Available Currently, in simulation there is a trend towards using the distributed software tools, particularly ones, which are using cloud technologies and the Internet. The article considers a simulation educational tool, implemented as a web application using the Java language with special Java class library developed for simulation. It is focused on a discrete event approach to modeling, similarly to the GPSS language, and intended for queuing systems simulation.The structure of the models obtained using this class library is similar to that of the GPSS language models. Also, the simulation language interpreter similar to GPSS is created using this class library, with some differences in the individual statements.Simulation experiments are performed on the server-side, and on client-side you must use a browser with standard functions to enter the source code into HTML-created form. Mobile devices can be used as clients. The source code of a model can be represented both in the Java language using a class library and in the language similar to GPSS.The simulation system implements functions especially for educational process. For example, there is possibility for a student to upload learning materials on the server, send developed software and reports of test control to the teacher via the Internet, and receive a detailed assessment of their results from the teacher. Also detailed results of passed tests in learning modules are entered, and some other functions are implemented in the system.As examples, the article considers models of the m/M/n/0 type queuing system in Java with a class library, and in the language similar to GPSS, shows simulation results, and presents the analytical model and calculations for this system. Analytical calculations proved that the modeling system is useful, as it overlaps simulation results with the acceptable error. Some approaches to the interaction with students through the Internet, used in modeling environment, can

  10. A dependability modeling of software under hardware faults digitized system in nuclear power plants

    International Nuclear Information System (INIS)

    Choi, Jong Gyun

    1996-02-01

    An analytic approach to the dependability evaluation of software in the operational phase is suggested in this work with special attention to the physical fault effects on the software dependability : The physical faults considered are memory faults and the dependability measure in question is the reliability. The model is based on the simple reliability theory and the graph theory with the path decomposition micro model. The model represents an application software with a graph consisting of nodes and arcs that probabilistic ally determine the flow from node to node. Through proper transformation of nodes and arcs, the graph can be reduced to a simple two-node graph and the software failure probability is derived from this graph. This model can be extended to the software system which consists of several complete modules without modification. The derived model is validated by the computer simulation, where the software is transformed to a probabilistic control flow graph. Simulation also shows a different viewpoint of software failure behavior. Using this model, we predict the reliability of an application software and a software system in a digitized system(ILS system) in the nuclear power plant and show the sensitivity of the software reliability to the major physical parameters which affect the software failure in the normal operation phase. The derived model is validated by the computer simulation, where the software is transformed to a probabilistic control flow graph. Simulation also shows a different viewpoint of software failure behavior. Using this model, we predict the reliability of an application software and a software system in a digitized system (ILS system) is the nuclear power plant and show the sensitivity of the software reliability to the major physical parameters which affect the software failure in the normal operation phase. This modeling method is particularly attractive for medium size programs such as software used in digitized systems of

  11. Data systems and computer science: Software Engineering Program

    Science.gov (United States)

    Zygielbaum, Arthur I.

    1991-01-01

    An external review of the Integrated Technology Plan for the Civil Space Program is presented. This review is specifically concerned with the Software Engineering Program. The goals of the Software Engineering Program are as follows: (1) improve NASA's ability to manage development, operation, and maintenance of complex software systems; (2) decrease NASA's cost and risk in engineering complex software systems; and (3) provide technology to assure safety and reliability of software in mission critical applications.

  12. The SOFIA Mission Control System Software

    Science.gov (United States)

    Heiligman, G. M.; Brock, D. R.; Culp, S. D.; Decker, P. H.; Estrada, J. C.; Graybeal, J. B.; Nichols, D. M.; Paluzzi, P. R.; Sharer, P. J.; Pampell, R. J.; Papke, B. L.; Salovich, R. D.; Schlappe, S. B.; Spriestersbach, K. K.; Webb, G. L.

    1999-05-01

    The Stratospheric Observatory for Infrared Astronomy (SOFIA) will be delivered with a computerized mission control system (MCS). The MCS communicates with the aircraft's flight management system and coordinates the operations of the telescope assembly, mission-specific subsystems, and the science instruments. The software for the MCS must be reliable and flexible. It must be easily usable by many teams of observers with widely differing needs, and it must support non-intrusive access for education and public outreach. The technology must be appropriate for SOFIA's 20-year lifetime. The MCS software development process is an object-oriented, use case driven approach. The process is iterative: delivery will be phased over four "builds"; each build will be the result of many iterations; and each iteration will include analysis, design, implementation, and test activities. The team is geographically distributed, coordinating its work via Web pages, teleconferences, T.120 remote collaboration, and CVS (for Internet-enabled configuration management). The MCS software architectural design is derived in part from other observatories' experience. Some important features of the MCS are: * distributed computing over several UNIX and VxWorks computers * fast throughput of time-critical data * use of third-party components, such as the Adaptive Communications Environment (ACE) and the Common Object Request Broker Architecture (CORBA) * extensive configurability via stored, editable configuration files * use of several computer languages so developers have "the right tool for the job". C++, Java, scripting languages, Interactive Data Language (from Research Systems, Int'l.), XML, and HTML will all be used in the final deliverables. This paper reports on work in progress, with the final product scheduled for delivery in 2001. This work was performed for Universities Space Research Association for NASA under contract NAS2-97001.

  13. 78 FR 47015 - Software Requirement Specifications for Digital Computer Software Used in Safety Systems of...

    Science.gov (United States)

    2013-08-02

    ... NUCLEAR REGULATORY COMMISSION [NRC-2012-0195] Software Requirement Specifications for Digital Computer Software Used in Safety Systems of Nuclear Power Plants AGENCY: Nuclear Regulatory Commission... issuing a revised regulatory guide (RG), revision 1 of RG 1.172, ``Software Requirement Specifications for...

  14. Solar thermal power plants simulation using the TRNSYS software

    Energy Technology Data Exchange (ETDEWEB)

    Popel, O.S.; Frid, S.E.; Shpilrain, E.E. [Institute for High Temperatures, Russian Academy of Sciences (IVTAN), Moscow (Russian Federation)

    1999-03-01

    The paper describes activity directed on the TRNSYS software application for mathematical simulation of solar thermal power plants. First stage of developments has been devoted to simulation and thermodynamic analysis of the Hybrid Solar-Fuel Thermal Power Plants (HSFTPP) with gas turbine installations. Three schemes of HSFTPP, namely: Gas Turbine Regenerative Cycle, Brayton Cycle with Steam Injection and Combined Brayton-Rankine Cycle,- have been assembled and tested under the TRNSYS. For this purpose 18 new models of the schemes components (gas and steam turbines, compressor, heat-exchangers, steam generator, solar receiver, condenser, controllers, etc) have been elaborated and incorporated into the TRNSYS library of 'standard' components. The authors do expect that this initiative and received results will stimulate experts involved in the mathematical simulation of solar thermal power plants to join the described activity to contribute to acceleration of development and expansion of 'Solar Thermal Power Plants' branch of the TRNSYS. The proposed approach could provide an appropriate basis for standardization of analysis, models and assumptions for well-founded comparison of different schemes of advanced solar power plants. (authors)

  15. System Risk Balancing Profiles: Software Component

    Science.gov (United States)

    Kelly, John C.; Sigal, Burton C.; Gindorf, Tom

    2000-01-01

    The Software QA / V&V guide will be reviewed and updated based on feedback from NASA organizations and others with a vested interest in this area. Hardware, EEE Parts, Reliability, and Systems Safety are a sample of the future guides that will be developed. Cost Estimates, Lessons Learned, Probability of Failure and PACTS (Prevention, Avoidance, Control or Test) are needed to provide a more complete risk management strategy. This approach to risk management is designed to help balance the resources and program content for risk reduction for NASA's changing environment.

  16. Automated remedial assessment methodology software system

    International Nuclear Information System (INIS)

    Whiting, M.; Wilkins, M.; Stiles, D.

    1994-11-01

    The Automated Remedial Analysis Methodology (ARAM) software system has been developed by the Pacific Northwest Laboratory to assist the U.S. Department of Energy (DOE) in evaluating cleanup options for over 10,000 contaminated sites across the DOE complex. The automated methodology comprises modules for decision logic diagrams, technology applicability and effectiveness rules, mass balance equations, cost and labor estimating factors and equations, and contaminant stream routing. ARAM is used to select technologies for meeting cleanup targets; determine the effectiveness of the technologies in destroying, removing, or immobilizing contaminants; decide the nature and amount of secondary waste requiring further treatment; and estimate the cost and labor involved when applying technologies

  17. CRISP90 - SOFTWARE DESIGN ANALYZER SYSTEM

    Science.gov (United States)

    Tausworthe, R. C.

    1994-01-01

    The CRISP90 Software Design Analyzer System, an update of CRISP-80, is a set of programs forming a software design and documentation tool which supports top-down, hierarchic, modular, structured design and programming methodologies. The quality of a computer program can often be significantly influenced by the design medium in which the program is developed. The medium must foster the expression of the programmer's ideas easily and quickly, and it must permit flexible and facile alterations, additions, and deletions to these ideas as the design evolves. The CRISP90 software design analyzer system was developed to provide the PDL (Programmer Design Language) programmer with such a design medium. A program design using CRISP90 consists of short, English-like textual descriptions of data, interfaces, and procedures that are imbedded in a simple, structured, modular syntax. The display is formatted into two-dimensional, flowchart-like segments for a graphic presentation of the design. Together with a good interactive full-screen editor or word processor, the CRISP90 design analyzer becomes a powerful tool for the programmer. In addition to being a text formatter, the CRISP90 system prepares material that would be tedious and error prone to extract manually, such as a table of contents, module directory, structure (tier) chart, cross-references, and a statistics report on the characteristics of the design. Referenced modules are marked by schematic logic symbols to show conditional, iterative, and/or concurrent invocation in the program. A keyword usage profile can be generated automatically and glossary definitions inserted into the output documentation. Another feature is the capability to detect changes that were made between versions. Thus, "change-bars" can be placed in the output document along with a list of changed pages and a version history report. Also, items may be marked as "to be determined" and each will appear on a special table until the item is

  18. Launch Control System Software Development System Automation Testing

    Science.gov (United States)

    Hwang, Andrew

    2017-01-01

    The Spaceport Command and Control System (SCCS) is the National Aeronautics and Space Administration's (NASA) launch control system for the Orion capsule and Space Launch System, the next generation manned rocket currently in development. This system requires high quality testing that will measure and test the capabilities of the system. For the past two years, the Exploration and Operations Division at Kennedy Space Center (KSC) has assigned a group including interns and full-time engineers to develop automated tests to save the project time and money. The team worked on automating the testing process for the SCCS GUI that would use streamed simulated data from the testing servers to produce data, plots, statuses, etc. to the GUI. The software used to develop automated tests included an automated testing framework and an automation library. The automated testing framework has a tabular-style syntax, which means the functionality of a line of code must have the appropriate number of tabs for the line to function as intended. The header section contains either paths to custom resources or the names of libraries being used. The automation library contains functionality to automate anything that appears on a desired screen with the use of image recognition software to detect and control GUI components. The data section contains any data values strictly created for the current testing file. The body section holds the tests that are being run. The function section can include any number of functions that may be used by the current testing file or any other file that resources it. The resources and body section are required for all test files; the data and function sections can be left empty if the data values and functions being used are from a resourced library or another file. To help equip the automation team with better tools, the Project Lead of the Automated Testing Team, Jason Kapusta, assigned the task to install and train an optical character recognition (OCR

  19. Software qualification for digital safety system in KNICS project

    International Nuclear Information System (INIS)

    Kwon, Kee-Choon; Lee, Dong-Young; Choi, Jong-Gyun

    2012-01-01

    In order to achieve technical self-reliance in the area of nuclear instrumentation and control, the Korea Nuclear Instrumentation and Control System (KNICS) project had been running for seven years from 2001. The safety-grade Programmable Logic Controller (PLC) and the digital safety system were developed by KNICS project. All the software of the PLC and digital safety system were developed and verified following the software development life cycle Verification and Validation (V and V) procedure. The main activities of the V and V process are preparation of software planning documentations, verification of the Software Requirement Specification (SRS), Software Design Specification (SDS) and codes, and a testing of the software components, the integrated software, and the integrated system. In addition, a software safety analysis and a software configuration management are included in the activities. For the software safety analysis at the SRS and SDS phases, the software Hazard Operability (HAZOP) was performed and then the software fault tree analysis was applied. The software fault tree analysis was applied to a part of software module with some critical defects identified by the software HAZOP in SDS phase. The software configuration management was performed using the in-house tool developed in the KNICS project. (author)

  20. Software Configuration Management Plan for the Sodium Removal System

    International Nuclear Information System (INIS)

    HILL, L.F.

    2000-01-01

    This document establishers the Software Configuration Management Plan (SCMP) for the software associated with the control system of the Sodium Removal System (SRS) located in the Interim Examination and Maintenance (IEM Cell) Facility of the FFTF Flux Test

  1. NASA Operational Simulator for Small Satellites: Tools for Software Based Validation and Verification of Small Satellites

    Science.gov (United States)

    Grubb, Matt

    2016-01-01

    The NASA Operational Simulator for Small Satellites (NOS3) is a suite of tools to aid in areas such as software development, integration test (IT), mission operations training, verification and validation (VV), and software systems check-out. NOS3 provides a software development environment, a multi-target build system, an operator interface-ground station, dynamics and environment simulations, and software-based hardware models. NOS3 enables the development of flight software (FSW) early in the project life cycle, when access to hardware is typically not available. For small satellites there are extensive lead times on many of the commercial-off-the-shelf (COTS) components as well as limited funding for engineering test units (ETU). Considering the difficulty of providing a hardware test-bed to each developer tester, hardware models are modeled based upon characteristic data or manufacturers data sheets for each individual component. The fidelity of each hardware models is such that FSW executes unaware that physical hardware is not present. This allows binaries to be compiled for both the simulation environment, and the flight computer, without changing the FSW source code. For hardware models that provide data dependent on the environment, such as a GPS receiver or magnetometer, an open-source tool from NASA GSFC (42 Spacecraft Simulation) is used to provide the necessary data. The underlying infrastructure used to transfer messages between FSW and the hardware models can also be used to monitor, intercept, and inject messages, which has proven to be beneficial for VV of larger missions such as James Webb Space Telescope (JWST). As hardware is procured, drivers can be added to the environment to enable hardware-in-the-loop (HWIL) testing. When strict time synchronization is not vital, any number of combinations of hardware components and software-based models can be tested. The open-source operator interface used in NOS3 is COSMOS from Ball Aerospace. For

  2. Assessing waste management systems using reginalt software

    International Nuclear Information System (INIS)

    Meshkov, N.K.; Camasta, S.F.; Gilbert, T.L.

    1988-03-01

    A method for assessing management systems for low-level radioactive waste is being developed for US Department of Energy. The method is based on benefit-cost-risk analysis. Waste management is broken down into its component steps, which are generation, treatment, packaging, storage, transportation, and disposal. Several different alternatives available for each waste management step are described. A particular waste management system consists of a feasible combination of alternatives for each step. Selecting an optimal waste management system would generally proceed as follows: (1) qualitative considerations are used to narrow down the choice of waste management system alternatives to a manageable number; (2) the costs and risks for each of these system alternatives are evaluated; (3) the number of alternatives is further reduced by eliminating alternatives with similar risks but higher costs, or those with similar costs but higher risks; (4) a trade-off factor between cost and risk is chosen and used to compute the objective function (sum of the cost and risk); and (5) the selection of the optimal waste management system among the remaining alternatives is made by choosing the alternative with the smallest value for the objective function. The authors propose that the REGINALT software system, developed by EG and G Idaho, Inc., as an acid for managers of low-level commerical waste, be augmented for application to the managment of DOE-generated waste. Specific recommendations for modification of the REGINALT system are made. 51 refs., 3 figs., 2 tabs

  3. Software packages for simulating groundwater flow and the spreading of soluble and insoluble admixtures in aquifers

    International Nuclear Information System (INIS)

    Roshal, A.A.; Klein, I.S.; Svishchov, A.M.

    1993-01-01

    Software programs are described designed for solving hydrogeological and environmental problems related to the analysis and prediction of groundwater flow and the spreading of solutes and insolubles in the saturated zones. The software package GWFS (Ground Water Flow Simulation) allows for simulating steady-state and unsteady-state flow in confined, unconfined, and confined-unconfined multi-layer and quasi-3D isotropic and anisotropic aquifer systems. Considered are intra-layer sources and sinks, infiltration, inter-layer leakages, the interrelationships with surface reservoirs and streams, interrelationships with the drains, aquifer discharge to surface sources. The MTS (Mass Transport Simulation) package is designed for solving solute transport problems. Taken into account is convective transport, hydrodynamic dispersion and diffusion, linear equilibrium sorption. The method of characteristics is being implemented here using the ''particles-in-cells'' scheme in which the transport is modeled with the help of tracers. The software package OWFS (Oil-Water Flow Simulation) is designed for the simulation of hydrocarbon (oil-water) migration in aquifers

  4. Fluctuating Finite Element Analysis (FFEA): A continuum mechanics software tool for mesoscale simulation of biomolecules.

    Science.gov (United States)

    Solernou, Albert; Hanson, Benjamin S; Richardson, Robin A; Welch, Robert; Read, Daniel J; Harlen, Oliver G; Harris, Sarah A

    2018-03-01

    Fluctuating Finite Element Analysis (FFEA) is a software package designed to perform continuum mechanics simulations of proteins and other globular macromolecules. It combines conventional finite element methods with stochastic thermal noise, and is appropriate for simulations of large proteins and protein complexes at the mesoscale (length-scales in the range of 5 nm to 1 μm), where there is currently a paucity of modelling tools. It requires 3D volumetric information as input, which can be low resolution structural information such as cryo-electron tomography (cryo-ET) maps or much higher resolution atomistic co-ordinates from which volumetric information can be extracted. In this article we introduce our open source software package for performing FFEA simulations which we have released under a GPLv3 license. The software package includes a C ++ implementation of FFEA, together with tools to assist the user to set up the system from Electron Microscopy Data Bank (EMDB) or Protein Data Bank (PDB) data files. We also provide a PyMOL plugin to perform basic visualisation and additional Python tools for the analysis of FFEA simulation trajectories. This manuscript provides a basic background to the FFEA method, describing the implementation of the core mechanical model and how intermolecular interactions and the solvent environment are included within this framework. We provide prospective FFEA users with a practical overview of how to set up an FFEA simulation with reference to our publicly available online tutorials and manuals that accompany this first release of the package.

  5. 14 CFR 415.123 - Computing systems and software.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Computing systems and software. 415.123... Launch Vehicle From a Non-Federal Launch Site § 415.123 Computing systems and software. (a) An applicant's safety review document must describe all computing systems and software that perform a safety...

  6. AIRMaster: Compressed air system audit software

    International Nuclear Information System (INIS)

    Wheeler, G.M.; Bessey, E.G.; McGill, R.D.; Vischer, K.

    1997-01-01

    The project goal was to develop a software tool, AIRMaster, and a methodology for performing compressed air system audits. AIRMaster and supporting manuals are designed for general auditors or plant personnel to evaluate compressed air system operation with simple instrumentation during a short-term audit. AIRMaster provides a systematic approach to compressed air system audits, analyzing collected data, and reporting results. AIRMaster focuses on inexpensive Operation and Maintenance (O and M) measures, such as fixing air leaks and improving controls that can significantly improve performance and reliability of the compressed air system, without significant risk to production. An experienced auditor can perform an audit, analyze collected data, and produce results in 2--3 days. AIRMaster reduces the cost of an audit, thus freeing funds to implement recommendations. The AIRMaster package includes an Audit Manual, Software and User's manual, Analysis Methodology Manual, and a Case Studies summary report. It also includes a Self-Guided Tour booklet to help users quickly screen a plant for efficiency improvement potentials, and an Industrial Compressed Air Systems Energy Efficiency Guidebook. AIRMaster proved to be a fast and effective audit tool. In sever audits AIRMaster identified energy savings of 4,056,000 kWh, or 49.2% of annual compressor energy use, for a cost savings of $152,000. Total implementation costs were $94,700 for a project payback period of 0.6 years. Available airflow increased between 11% and 51% of plant compressor capacity, leading to potential capital benefits from 40% to 230% of first year energy savings

  7. Software for the Simulation of Power Plant Processes

    DEFF Research Database (Denmark)

    Elmegaard, Brian; Houbak, Niels

    2002-01-01

    description of many static and/or dynamic energy system or process simulators. It discusses the principal implementation of the model handling in DNA and finally, there is a small example illustrating that too simple component models may under certain circumstances result in an erroneous, singular model.......Modelling of energy systems has been increasingly more important. In particular the dynamic behaviour is critical when operating the systems closer to the limits (either of the process, the materials, the emissions or the economics, etc.). This enforces strong requirements on both the models...... and their numerical solution with respect to both accuracy and efficiency. In part A of this paper we give a survey on simulation of energy systems, from models and modelling, over numerical methods to implementational techniques. It covers important aspects of the different phases of modelling of a (energy) system...

  8. Parallel and Distributed System Simulation

    Science.gov (United States)

    Dongarra, Jack

    1998-01-01

    This exploratory study initiated our research into the software infrastructure necessary to support the modeling and simulation techniques that are most appropriate for the Information Power Grid. Such computational power grids will use high-performance networking to connect hardware, software, instruments, databases, and people into a seamless web that supports a new generation of computation-rich problem solving environments for scientists and engineers. In this context we looked at evaluating the NetSolve software environment for network computing that leverages the potential of such systems while addressing their complexities. NetSolve's main purpose is to enable the creation of complex applications that harness the immense power of the grid, yet are simple to use and easy to deploy. NetSolve uses a modular, client-agent-server architecture to create a system that is very easy to use. Moreover, it is designed to be highly composable in that it readily permits new resources to be added by anyone willing to do so. In these respects NetSolve is to the Grid what the World Wide Web is to the Internet. But like the Web, the design that makes these wonderful features possible can also impose significant limitations on the performance and robustness of a NetSolve system. This project explored the design innovations that push the performance and robustness of the NetSolve paradigm as far as possible without sacrificing the Web-like ease of use and composability that make it so powerful.

  9. Simulation Based Studies in Software Engineering: A Matter of Validity

    Directory of Open Access Journals (Sweden)

    Breno Bernard Nicolau de França

    2015-04-01

    Full Text Available Despite the possible lack of validity when compared with other science areas, Simulation-Based Studies (SBS in Software Engineering (SE have supported the achievement of some results in the field. However, as it happens with any other sort of experimental study, it is important to identify and deal with threats to validity aiming at increasing their strength and reinforcing results confidence. OBJECTIVE: To identify potential threats to SBS validity in SE and suggest ways to mitigate them. METHOD: To apply qualitative analysis in a dataset resulted from the aggregation of data from a quasi-systematic literature review combined with ad-hoc surveyed information regarding other science areas. RESULTS: The analysis of data extracted from 15 technical papers allowed the identification and classification of 28 different threats to validity concerned with SBS in SE according Cook and Campbell’s categories. Besides, 12 verification and validation procedures applicable to SBS were also analyzed and organized due to their ability to detect these threats to validity. These results were used to make available an improved set of guidelines regarding the planning and reporting of SBS in SE. CONCLUSIONS: Simulation based studies add different threats to validity when compared with traditional studies. They are not well observed and therefore, it is not easy to identify and mitigate all of them without explicit guidance, as the one depicted in this paper.

  10. Sandia National Laboratories Advanced Simulation and Computing (ASC) software quality plan : ASC software quality engineering practices Version 3.0.

    Energy Technology Data Exchange (ETDEWEB)

    Turgeon, Jennifer L.; Minana, Molly A.; Hackney, Patricia; Pilch, Martin M.

    2009-01-01

    The purpose of the Sandia National Laboratories (SNL) Advanced Simulation and Computing (ASC) Software Quality Plan is to clearly identify the practices that are the basis for continually improving the quality of ASC software products. Quality is defined in the US Department of Energy/National Nuclear Security Agency (DOE/NNSA) Quality Criteria, Revision 10 (QC-1) as 'conformance to customer requirements and expectations'. This quality plan defines the SNL ASC Program software quality engineering (SQE) practices and provides a mapping of these practices to the SNL Corporate Process Requirement (CPR) 001.3.6; 'Corporate Software Engineering Excellence'. This plan also identifies ASC management's and the software project teams responsibilities in implementing the software quality practices and in assessing progress towards achieving their software quality goals. This SNL ASC Software Quality Plan establishes the signatories commitments to improving software products by applying cost-effective SQE practices. This plan enumerates the SQE practices that comprise the development of SNL ASC's software products and explains the project teams opportunities for tailoring and implementing the practices.

  11. The Australian Computational Earth Systems Simulator

    Science.gov (United States)

    Mora, P.; Muhlhaus, H.; Lister, G.; Dyskin, A.; Place, D.; Appelbe, B.; Nimmervoll, N.; Abramson, D.

    2001-12-01

    Numerical simulation of the physics and dynamics of the entire earth system offers an outstanding opportunity for advancing earth system science and technology but represents a major challenge due to the range of scales and physical processes involved, as well as the magnitude of the software engineering effort required. However, new simulation and computer technologies are bringing this objective within reach. Under a special competitive national funding scheme to establish new Major National Research Facilities (MNRF), the Australian government together with a consortium of Universities and research institutions have funded construction of the Australian Computational Earth Systems Simulator (ACcESS). The Simulator or computational virtual earth will provide the research infrastructure to the Australian earth systems science community required for simulations of dynamical earth processes at scales ranging from microscopic to global. It will consist of thematic supercomputer infrastructure and an earth systems simulation software system. The Simulator models and software will be constructed over a five year period by a multi-disciplinary team of computational scientists, mathematicians, earth scientists, civil engineers and software engineers. The construction team will integrate numerical simulation models (3D discrete elements/lattice solid model, particle-in-cell large deformation finite-element method, stress reconstruction models, multi-scale continuum models etc) with geophysical, geological and tectonic models, through advanced software engineering and visualization technologies. When fully constructed, the Simulator aims to provide the software and hardware infrastructure needed to model solid earth phenomena including global scale dynamics and mineralisation processes, crustal scale processes including plate tectonics, mountain building, interacting fault system dynamics, and micro-scale processes that control the geological, physical and dynamic

  12. A Simulation Approach for Performance Validation during Embedded Systems Design

    Science.gov (United States)

    Wang, Zhonglei; Haberl, Wolfgang; Herkersdorf, Andreas; Wechs, Martin

    Due to the time-to-market pressure, it is highly desirable to design hardware and software of embedded systems in parallel. However, hardware and software are developed mostly using very different methods, so that performance evaluation and validation of the whole system is not an easy task. In this paper, we propose a simulation approach to bridge the gap between model-driven software development and simulation based hardware design, by merging hardware and software models into a SystemC based simulation environment. An automated procedure has been established to generate software simulation models from formal models, while the hardware design is originally modeled in SystemC. As the simulation models are annotated with timing information, performance issues are tackled in the same pass as system functionality, rather than in a dedicated approach.

  13. System software of the CERN proton synchrotron control system

    International Nuclear Information System (INIS)

    Carpenter, B.E.; Cailliau, R.; Cuisinier, G.; Remmer, W.

    1984-01-01

    The PS complex consists of 10 different interconnected accelerators or storage rings, mainly controlled by the same distributed system of NORD-10 and ND-100 minicomputers. After a brief outline of the hardware, this report gives a detailed description of the system software, which is based on the SINTRAN III operating system. It describes the general layout of the software, the network, CAMAC access, programming languages, program development, and microprocessor support. It concludes with reviews of performance, documentation, organization and methods, and future prospects. (orig.)

  14. Practical integrated simulation systems for coupled numerical simulations in parallel

    Energy Technology Data Exchange (ETDEWEB)

    Osamu, Hazama; Zhihong, Guo [Japan Atomic Energy Research Inst., Centre for Promotion of Computational Science and Engineering, Tokyo (Japan)

    2003-07-01

    In order for the numerical simulations to reflect 'real-world' phenomena and occurrences, incorporation of multidisciplinary and multi-physics simulations considering various physical models and factors are becoming essential. However, there still exist many obstacles which inhibit such numerical simulations. For example, it is still difficult in many instances to develop satisfactory software packages which allow for such coupled simulations and such simulations will require more computational resources. A precise multi-physics simulation today will require parallel processing which again makes it a complicated process. Under the international cooperative efforts between CCSE/JAERI and Fraunhofer SCAI, a German institute, a library called the MpCCI, or Mesh-based Parallel Code Coupling Interface, has been implemented together with a library called STAMPI to couple two existing codes to develop an 'integrated numerical simulation system' intended for meta-computing environments. (authors)

  15. Inertisation and mine fire simulation using computer software

    Energy Technology Data Exchange (ETDEWEB)

    Stewart Gillies; Hsin Wei Wu [Gillies Wu Mining Technology (Australia)

    2007-05-15

    Inertisation is a technique used to enhance the safety of underground coal mine areas either to avoid the potential for a combustion event or to stabilise a situation after an ignition, fire or heating. The primary objective of the study was to review coal mine inertisation in Australia, in particular, to focus on the use of the Polish mine fire simulation software 'VENTGRAPH' to gain better understanding of how inertisation (GAG, Mineshield, Nitrogen Pressure Swing Adsorption (Floxal) and Tomlinson Boiler) units interact with the complex ventilation behaviour underground during a substantial fire. Most emphasis has been given to understanding the behaviour of the GAG unit because of its high capacity output. Critical aspects targeted for examination include location of the unit for high priority fire positions, size of borehole or pipe range required, time required for inertisation output to interact with and extinguish a fire, effects of seam gases on fire behaviour with inertisation present and main fan management. The project aims to increase understanding of behaviour of mine fires in modern mine ventilation networks with the addition of inert gas streams. A second aim of the project has been to take findings from the simulation exercises and develop inertisation related modifications to the program in conjunction with the Polish program authors. Exercises based on Oaky North and Oaky No 1 mines have involved 'evaluation or auditing' of ability to deliver inert gases generated from GAG units to high priority underground fire locations. These exercises have been built around modelling of fire scenarios across the mine layouts. The fire simulation exercises at Oaky North and Oaky No 1 mines demonstrated that it is possible to efficiently evaluate possible inertisation strategies appropriate to a complex mine layout extracting a gassy seam and determine which approach strategy (if any) can be used to stabilise a mine in a timely fashion.

  16. DSC: software tool for simulation-based design of control strategies applied to wastewater treatment plants.

    Science.gov (United States)

    Ruano, M V; Ribes, J; Seco, A; Ferrer, J

    2011-01-01

    This paper presents a computer tool called DSC (Simulation based Controllers Design) that enables an easy design of control systems and strategies applied to wastewater treatment plants. Although the control systems are developed and evaluated by simulation, this tool aims to facilitate the direct implementation of the designed control system to the PC of the full-scale WWTP (wastewater treatment plants). The designed control system can be programmed in a dedicated control application and can be connected to either the simulation software or the SCADA of the plant. To this end, the developed DSC incorporates an OPC server (OLE for process control) which facilitates an open-standard communication protocol for different industrial process applications. The potential capabilities of the DSC tool are illustrated through the example of a full-scale application. An aeration control system applied to a nutrient removing WWTP was designed, tuned and evaluated with the DSC tool before its implementation in the full scale plant. The control parameters obtained by simulation were suitable for the full scale plant with only few modifications to improve the control performance. With the DSC tool, the control systems performance can be easily evaluated by simulation. Once developed and tuned by simulation, the control systems can be directly applied to the full-scale WWTP.

  17. The Trouble with Thinking like Arena: Learning to Use Simulation Software

    Science.gov (United States)

    Rodgers, Diane M.; Moraga, Reinaldo J.

    2011-01-01

    Simulation software used for modeling has become as ubiquitous as computers themselves. Despite growing reliance on simulation in educational and workplace settings, users encounter frustration in using simulation software programs. The authors conducted a study with 26 engineering students and interviewed them about their experience learning the…

  18. A comparative analysis of currently used microscopic and macroscopic traffic simulation software

    International Nuclear Information System (INIS)

    Ratrout Nedal T; Rahman Syed Masiur

    2009-01-01

    The significant advancements of information technology have contributed to increased development of traffic simulation models. These include microscopic models and broadening the areas of applications ranging from the modeling of specific components of the transportation system to a whole network having different kinds of intersections and links, even in a few cases combining travel demand models. This paper mainly reviews the features of traditionally used macroscopic and microscopic traffic simulation models along with a comparative analysis focusing on freeway operations, urban congested networks, project-level emission modeling, and variations in delay and capacity estimates. The models AIMSUN, CORSIM, and VISSIM are found to be suitable for congested arterials and freeways, and integrated networks of freeways and surface streets. The features of AIMSUN are favorable for creating large urban and regional networks. The models AIMSUN, PARAMICS, INTEGRATION, and CORSIM are potentially useful for Intelligent Transportation System (ITS). There are a few simulation models which are developed focusing on ITS such as MITSIMLab. The TRAF-family and HUTSIM models attempt a system-level simulation approach and develop open environments where several analysis models can be used interactively to solve traffic simulation problems. In Saudi Arabia, use of simulation software with the capability of analyzing an integrated system of freeways and surface streets has not been reported. Calibration and validation of simulation software either for freeways or surface streets has been reported. This paper suggests that researchers evaluate the state-of-the-art simulation tools and find out the suitable tools or approaches for the local conditions of Saudi Arabia. (author)

  19. A software system for oilfield facility investment minimization

    International Nuclear Information System (INIS)

    Ding, Z.X.; Startzman, R.A.

    1996-01-01

    Minimizing investment in oilfield development is an important subject that has attracted a considerable amount of industry attention. One method to reduce investment involves the optimal placement and selection of production facilities. Because of the large amount of capital used in this process, saving a small percent of the total investment may represent a large monetary value. The literature reports algorithms using mathematical programming techniques that were designed to solve the proposed problem in a global optimal manner. Owing to the high-computational complexity and the lack of user-friendly interfaces for data entry and results display, mathematical programming techniques have not been given enough attention in practice. This paper describes an interactive, graphical software system that provides a global optimal solution to the problem of placement and selection of production facilities in oil-field development processes. This software system can be used as an investment minimization tool and a scenario-study simulator. The developed software system consists of five basic modules: (1) an interactive data-input unit, (2) a cost function generator, (3) an optimization unit, (4) a graphic-output display, and (5) a sensitivity-analysis unit

  20. Software on the Peregrine System | High-Performance Computing | NREL

    Science.gov (United States)

    on the Peregrine System Software on the Peregrine System NREL maintains a variety of applications environment modules for use on Peregrine. Applications View list of software applications by name and research area/discipline. Libraries View list of software libraries available for linking and loading

  1. The Utility of Open Source Software in Military Systems

    National Research Council Canada - National Science Library

    Esperon, Agustin I; Munoz, Jose P; Tanneau, Jean M

    2005-01-01

    .... The companies involved were THALES and GMV. The MILOS project aimed to demonstrate benefits of Open Source Software in large software based military systems, by casting off constraints inherent to traditional proprietary COTS and by taking...

  2. Analyzing Software Errors in Safety-Critical Embedded Systems

    Science.gov (United States)

    Lutz, Robyn R.

    1994-01-01

    This paper analyzes the root causes of safty-related software faults identified as potentially hazardous to the system are distributed somewhat differently over the set of possible error causes than non-safety-related software faults.

  3. Using CASE Software to Teach Undergraduates Systems Analysis and Design.

    Science.gov (United States)

    Wilcox, Russell E.

    1988-01-01

    Describes the design and delivery of a college course for information system students utilizing a Computer-Aided Software Engineering program. Discusses class assignments, cooperative learning, student attitudes, and the advantages of using this software in the course. (CW)

  4. A communication-channel-based representation system for software

    NARCIS (Netherlands)

    Demirezen, Zekai; Tanik, Murat M.; Aksit, Mehmet; Skjellum, Anthony

    We observed that before initiating software development the objectives are minimally organized and developers introduce comparatively higher organization throughout the design process. To be able to formally capture this observation, a new communication channel representation system for software is

  5. Innovative simulation systems

    CERN Document Server

    Jędrasiak, Karol

    2016-01-01

    This monograph provides comprehensive guidelines on the current and future trends of innovative simulation systems. In particular, their important components, such as augmented reality and unmanned vehicles are presented. The book consists of three parts. Each part presents good practices, new methods, concepts of systems and new algorithms. Presented challenges and solutions are the results of research and conducted by the contributing authors. The book describes and evaluates the current state of knowledge in the field of innovative simulation systems. Throughout the chapters there are presented current issues and concepts of systems, technology, equipment, tools, research challenges and current, past and future applications of simulation systems. The book is addressed to a wide audience: academic staff, representatives of research institutions, employees of companies and government agencies as well as students and graduates of technical universities in the country and abroad. The book can be a valuable sou...

  6. Engineering Software Suite Validates System Design

    Science.gov (United States)

    2007-01-01

    EDAptive Computing Inc.'s (ECI) EDAstar engineering software tool suite, created to capture and validate system design requirements, was significantly funded by NASA's Ames Research Center through five Small Business Innovation Research (SBIR) contracts. These programs specifically developed Syscape, used to capture executable specifications of multi-disciplinary systems, and VectorGen, used to automatically generate tests to ensure system implementations meet specifications. According to the company, the VectorGen tests considerably reduce the time and effort required to validate implementation of components, thereby ensuring their safe and reliable operation. EDASHIELD, an additional product offering from ECI, can be used to diagnose, predict, and correct errors after a system has been deployed using EDASTAR -created models. Initial commercialization for EDASTAR included application by a large prime contractor in a military setting, and customers include various branches within the U.S. Department of Defense, industry giants like the Lockheed Martin Corporation, Science Applications International Corporation, and Ball Aerospace and Technologies Corporation, as well as NASA's Langley and Glenn Research Centers

  7. Command and Control System Software Development

    Science.gov (United States)

    Velasquez, Ricky

    2017-01-01

    Kennedy Space Center has been the heart of human space flight for decades. From the Apollo Program to the Space Shuttle Program, and now to the coming Space Launch System (SLS) and Orion, NASA will be a leader in deep space exploration for mankind. Before any rockets blast off, there is significant work to be done in preparation for launch. People working on all aspects of spaceflight must contribute by developing new technology that has yet to participate in a successful launch, and which can work with technology already proven in flight. These innovations, whether hardware or software, must be tried and true, and includes the projects to which interns contribute to. For this internship, the objective was to create a data recording system for the developers of a LCS section that records certain messages in the traffic of the system. Developers would then be able to use these recordings for analysis later on, either manually or by an automated test. The tool would be of convenience to a developer as it would be used if the system's main data recorder was not available for tests.

  8. Design of penicillin fermentation process simulation system

    Science.gov (United States)

    Qi, Xiaoyu; Yuan, Zhonghu; Qi, Xiaoxuan; Zhang, Wenqi

    2011-10-01

    Real-time monitoring for batch process attracts increasing attention. It can ensure safety and provide products with consistent quality. The design of simulation system of batch process fault diagnosis is of great significance. In this paper, penicillin fermentation, a typical non-linear, dynamic, multi-stage batch production process, is taken as the research object. A visual human-machine interactive simulation software system based on Windows operation system is developed. The simulation system can provide an effective platform for the research of batch process fault diagnosis.

  9. Modeling and Analysis of Helicopter Ground Resonance Utilizing Symbolic Processing and Dynamic Simulation Software

    National Research Council Canada - National Science Library

    Robinson, Christopher

    1997-01-01

    ...) source code formatted specifically for numerical integration. The compiled source code can be accessed and numerically integrated by the dynamic simulation software SIMULINK(registered). SIMULINK(registered...

  10. Cogeneration system simulation/optimization

    International Nuclear Information System (INIS)

    Puppa, B.A.; Chandrashekar, M.

    1992-01-01

    Companies are increasingly turning to computer software programs to improve and streamline the analysis o cogeneration systems. This paper introduces a computer program which originated with research at the University of Waterloo. The program can simulate and optimize any type of layout of cogeneration plant. An application of the program to a cogeneration feasibility study for a university campus is described. The Steam and Power Plant Optimization System (SAPPOS) is a PC software package which allows users to model any type of steam/power plant on a component-by-component basis. Individual energy/steam balances can be done quickly to model any scenario. A typical days per month cogeneration simulation can also be carried out to provide a detailed monthly cash flow and energy forecast. This paper reports that SAPPOS can be used for scoping, feasibility, and preliminary design work, along with financial studies, gas contract studies, and optimizing the operation of completed plants. In the feasibility study presented, SAPPOS is used to evaluate both diesel engine and gas turbine combined cycle options

  11. Model-Based GN and C Simulation and Flight Software Development for Orion Missions beyond LEO

    Science.gov (United States)

    Odegard, Ryan; Milenkovic, Zoran; Henry, Joel; Buttacoli, Michael

    2014-01-01

    For Orion missions beyond low Earth orbit (LEO), the Guidance, Navigation, and Control (GN&C) system is being developed using a model-based approach for simulation and flight software. Lessons learned from the development of GN&C algorithms and flight software for the Orion Exploration Flight Test One (EFT-1) vehicle have been applied to the development of further capabilities for Orion GN&C beyond EFT-1. Continuing the use of a Model-Based Development (MBD) approach with the Matlab®/Simulink® tool suite, the process for GN&C development and analysis has been largely improved. Furthermore, a model-based simulation environment in Simulink, rather than an external C-based simulation, greatly eases the process for development of flight algorithms. The benefits seen by employing lessons learned from EFT-1 are described, as well as the approach for implementing additional MBD techniques. Also detailed are the key enablers for improvements to the MBD process, including enhanced configuration management techniques for model-based software systems, automated code and artifact generation, and automated testing and integration.

  12. ROSE: A realtime object oriented software environment for high fidelity replica simulation

    International Nuclear Information System (INIS)

    Abramovitch, A.

    1994-01-01

    An object oriented software environment used for the production testing and documentation of real time models for high fidelity training simulators encompasses a wide variety of software constructs including code generators for various classes of physical systems, model executive control programs, a high resolution graphics editor, as well as databases and associated access routines used to store and control information transfer among the various software entities. CAE Electronics' newly developed ROSE allows for the generation and integrated test of thermalhydraulic, analog control, digital control and electrical system models. Based on an iconical/standard subroutine representation of standard plant components along with an admittance matrix solution governed by the topology of the system under consideration, the ROSE blends together network solution algorithms and standard component models, both previously time tested via manual implementation into a single integrated automated software environment. The methodology employed to construct the ROSE, along with a synopsis of the various CASE tools integrated together to form a complete graphics based system for high fidelity real time code generation and validation is described in the presentation. (1 fig.)

  13. Immune system simulation online

    DEFF Research Database (Denmark)

    Rapin, Nicolas; Lund, Ole; Castiglione, Filippo

    2011-01-01

    MOTIVATION: The recognition of antigenic peptides is a major event of an immune response. In current mesoscopic-scale simulators of the immune system, this crucial step has been modeled in a very approximated way. RESULTS: We have equipped an agent-based model of the immune system with immuno...

  14. Treatment planning in radiosurgery: parallel Monte Carlo simulation software

    Energy Technology Data Exchange (ETDEWEB)

    Scielzo, G [Galliera Hospitals, Genova (Italy). Dept. of Hospital Physics; Grillo Ruggieri, F [Galliera Hospitals, Genova (Italy) Dept. for Radiation Therapy; Modesti, M; Felici, R [Electronic Data System, Rome (Italy); Surridge, M [University of South Hampton (United Kingdom). Parallel Apllication Centre

    1995-12-01

    The main objective of this research was to evaluate the possibility of direct Monte Carlo simulation for accurate dosimetry with short computation time. We made us of: graphics workstation, linear accelerator, water, PMMA and anthropomorphic phantoms, for validation purposes; ionometric, film and thermo-luminescent techniques, for dosimetry; treatment planning system for comparison. Benchmarking results suggest that short computing times can be obtained with use of the parallel version of EGS4 that was developed. Parallelism was obtained assigning simulation incident photons to separate processors, and the development of a parallel random number generator was necessary. Validation consisted in: phantom irradiation, comparison of predicted and measured values good agreement in PDD and dose profiles. Experiments on anthropomorphic phantoms (with inhomogeneities) were carried out, and these values are being compared with results obtained with the conventional treatment planning system.

  15. RT-Syn: A real-time software system generator

    Science.gov (United States)

    Setliff, Dorothy E.

    1992-01-01

    This paper presents research into providing highly reusable and maintainable components by using automatic software synthesis techniques. This proposal uses domain knowledge combined with automatic software synthesis techniques to engineer large-scale mission-critical real-time software. The hypothesis centers on a software synthesis architecture that specifically incorporates application-specific (in this case real-time) knowledge. This architecture synthesizes complex system software to meet a behavioral specification and external interaction design constraints. Some examples of these external constraints are communication protocols, precisions, timing, and space limitations. The incorporation of application-specific knowledge facilitates the generation of mathematical software metrics which are used to narrow the design space, thereby making software synthesis tractable. Success has the potential to dramatically reduce mission-critical system life-cycle costs not only by reducing development time, but more importantly facilitating maintenance, modifications, and extensions of complex mission-critical software systems, which are currently dominating life cycle costs.

  16. Systems and software quality the next step for industrialisation

    CERN Document Server

    Wieczorek, Martin; Bons, Heinz

    2014-01-01

    Software and systems quality is playing an increasingly important role in the growth of almost all - profit and non-profit - organisations. Quality is vital to the success of enterprises in their markets. Most small trade and repair businesses use software systems in their administration and marketing processes. Every doctor's surgery is managing its patients using software. Banking is no longer conceivable without software. Aircraft, trucks and cars use more and more software to handle their increasingly complex technical systems. Innovation, competition and cost pressure are always present i

  17. Tank monitor and control system (TMACS) software configuration management plan

    International Nuclear Information System (INIS)

    GLASSCOCK, J.A.

    1999-01-01

    This Software Configuration Management Plan (SCMP) describes the methodology for control of computer software developed and supported by the Systems Development and Integration (SD and I) organization of Lockheed Martin Services, Inc. (LMSI) for the Tank Monitor and Control System (TMACS). This plan controls changes to the software and configuration files used by TMACS. The controlled software includes the Gensym software package, Gensym knowledge base files developed for TMACS, C-language programs used by TMACS, the operating system on the production machine, language compilers, and all Windows NT commands and functions which affect the operating environment. The configuration files controlled include the files downloaded to the Acromag and Westronic field instruments

  18. System support software for TSTA [Tritium Systems Test Assembly

    International Nuclear Information System (INIS)

    Claborn, G.W.; Mann, L.W.; Nielson, C.W.

    1987-10-01

    The fact that Tritium Systems Test Assembly (TSTA) is an experimental facility makes it impossible and undesirable to try to forecast the exact software requirements. Thus the software had to be written in a manner that would allow modifications without compromising the safety requirements imposed by the handling of tritium. This suggested a multi-level approach to the software. In this approach (much like the ISO network model) each level is isolated from the level below and above by cleanly defined interfaces. For example, the subsystem support level interfaces with the subsystem hardware through the software support level. Routines in the software support level provide operations like ''OPEN VALVE'' and CLOSE VALVE'' to the subsystem level. This isolates the subsystem level from the actual hardware. This is advantageous because changes can occur in any level without the need for propagating the change to any other level. The TSTA control system consists of the hardware level, the data conversion level, the operator interface level, and the subsystem process level. These levels are described

  19. A measurement system for large, complex software programs

    Science.gov (United States)

    Rone, Kyle Y.; Olson, Kitty M.; Davis, Nathan E.

    1994-01-01

    This paper describes measurement systems required to forecast, measure, and control activities for large, complex software development and support programs. Initial software cost and quality analysis provides the foundation for meaningful management decisions as a project evolves. In modeling the cost and quality of software systems, the relationship between the functionality, quality, cost, and schedule of the product must be considered. This explicit relationship is dictated by the criticality of the software being developed. This balance between cost and quality is a viable software engineering trade-off throughout the life cycle. Therefore, the ability to accurately estimate the cost and quality of software systems is essential to providing reliable software on time and within budget. Software cost models relate the product error rate to the percent of the project labor that is required for independent verification and validation. The criticality of the software determines which cost model is used to estimate the labor required to develop the software. Software quality models yield an expected error discovery rate based on the software size, criticality, software development environment, and the level of competence of the project and developers with respect to the processes being employed.

  20. The contribution of instrumentation and control software to system reliability

    International Nuclear Information System (INIS)

    Fryer, M.O.

    1984-01-01

    Advanced instrumentation and control systems are usually implemented using computers that monitor the instrumentation and issue commands to control elements. The control commands are based on instrument readings and software control logic. The reliability of the total system will be affected by the software design. When comparing software designs, an evaluation of how each design can contribute to the reliability of the system is desirable. Unfortunately, the science of reliability assessment of combined hardware and software systems is in its infancy. Reliability assessment of combined hardware/software systems is often based on over-simplified assumptions about software behavior. A new method of reliability assessment of combined software/hardware systems is presented. The method is based on a procedure called fault tree analysis which determines how component failures can contribute to system failure. Fault tree analysis is a well developed method for reliability assessment of hardware systems and produces quantitative estimates of failure probability based on component failure rates. It is shown how software control logic can be mapped into a fault tree that depicts both software and hardware contributions to system failure. The new method is important because it provides a way for quantitatively evaluating the reliability contribution of software designs. In many applications, this can help guide designers in producing safer and more reliable systems. An application to the nuclear power research industry is discussed

  1. Software Technology for Adaptable, Reliable Systems (STARS)

    Science.gov (United States)

    1994-03-25

    Tmeline(3), SECOMO(3), SEER(3), GSFC Software Engineering Lab Model(l), SLIM(4), SEER-SEM(l), SPQR (2), PRICE-S(2), internally-developed models(3), APMSS(1...3 " Timeline - 3 " SASET (Software Architecture Sizing Estimating Tool) - 2 " MicroMan 11- 2 * LCM (Logistics Cost Model) - 2 * SPQR - 2 * PRICE-S - 2

  2. Comparing internal and external run-time coupling of CFD and building energy simulation software

    NARCIS (Netherlands)

    Djunaedy, E.; Hensen, J.L.M.; Loomans, M.G.L.C.

    2004-01-01

    This paper describes a comparison between internal and external run-time coupling of CFD and building energy simulation software. Internal coupling can be seen as the "traditional" way of developing software, i.e. the capabilities of existing software are expanded by merging codes. With external

  3. Validation of X1 motorcycle model in industrial plant layout by using WITNESSTM simulation software

    Science.gov (United States)

    Hamzas, M. F. M. A.; Bareduan, S. A.; Zakaria, M. Z.; Tan, W. J.; Zairi, S.

    2017-09-01

    This paper demonstrates a case study on simulation, modelling and analysis for X1 Motorcycles Model. In this research, a motorcycle assembly plant has been selected as a main place of research study. Simulation techniques by using Witness software were applied to evaluate the performance of the existing manufacturing system. The main objective is to validate the data and find out the significant impact on the overall performance of the system for future improvement. The process of validation starts when the layout of the assembly line was identified. All components are evaluated to validate whether the data is significance for future improvement. Machine and labor statistics are among the parameters that were evaluated for process improvement. Average total cycle time for given workstations is used as criterion for comparison of possible variants. From the simulation process, the data used are appropriate and meet the criteria for two-sided assembly line problems.

  4. INDUSTRIAL ROBOT ARM SIMULATION SOFTWARE DEVELOPMENT USING JAVA-3D AND MATLAB SIMULINK PROGRAMMING LANGUAGE

    OpenAIRE

    Wirabhuana, Arya

    2011-01-01

    Robot Arms Simulation Software development using Structured Programming Languages, Third Party Language, and Artificial Intelligence Programming Language are the common techniques in simulating robot arms movement. Those three techniques are having its strengths and weaknesses depend on several constraints such as robot type, degree of operation complexity to be simulated, operator skills, and also computer capability. This paper will discuss on Robot Arms Simulation Software (RSS) developmen...

  5. EZVIDEO, DISSPLA Graphics Software Simulation on IBM PC

    International Nuclear Information System (INIS)

    1991-01-01

    1 - Description of program or function: EZVIDEO simulates a subset of the DISSPLA plotting package to make plots on the IBM PC screen. Screen dumps can also be made to an attached LaserJet or Epson printer to make hard copy without using terminal emulators. The forerunner of EZVIDEO was called EZPLOT. 2 - Method of solution: The subroutines in the EZVIDEO system are based on the Hewlett Packard HP 9000 simulation of DISSPLA. These routines manipulate the pen movements on the screen and are also capable of capturing these same movements so that a hardcopy can be made to dot matrix or laser printer. 3 - Restrictions on the complexity of the problem: For plotting on the IBM PC, the plotting emulator PCPLOT is needed

  6. An automated methodology development. [software design for combat simulation

    Science.gov (United States)

    Hawley, L. R.

    1985-01-01

    The design methodology employed in testing the applicability of Ada in large-scale combat simulations is described. Ada was considered as a substitute for FORTRAN to lower life cycle costs and ease the program development efforts. An object-oriented approach was taken, which featured definitions of military targets, the capability of manipulating their condition in real-time, and one-to-one correlation between the object states and real world states. The simulation design process was automated by the problem statement language (PSL)/problem statement analyzer (PSA). The PSL/PSA system accessed the problem data base directly to enhance the code efficiency by, e.g., eliminating non-used subroutines, and provided for automated report generation, besides allowing for functional and interface descriptions. The ways in which the methodology satisfied the responsiveness, reliability, transportability, modifiability, timeliness and efficiency goals are discussed.

  7. Progressive retry for software error recovery in distributed systems

    Science.gov (United States)

    Wang, Yi-Min; Huang, Yennun; Fuchs, W. K.

    1993-01-01

    In this paper, we describe a method of execution retry for bypassing software errors based on checkpointing, rollback, message reordering and replaying. We demonstrate how rollback techniques, previously developed for transient hardware failure recovery, can also be used to recover from software faults by exploiting message reordering to bypass software errors. Our approach intentionally increases the degree of nondeterminism and the scope of rollback when a previous retry fails. Examples from our experience with telecommunications software systems illustrate the benefits of the scheme.

  8. Telemetry and Science Data Software System

    Science.gov (United States)

    Bates, Lakesha; Hong, Liang

    2011-01-01

    The Telemetry and Science Data Software System (TSDSS) was designed to validate the operational health of a spacecraft, ease test verification, assist in debugging system anomalies, and provide trending data and advanced science analysis. In doing so, the system parses, processes, and organizes raw data from the Aquarius instrument both on the ground and while in space. In addition, it provides a user-friendly telemetry viewer, and an instant pushbutton test report generator. Existing ground data systems can parse and provide simple data processing, but have limitations in advanced science analysis and instant report generation. The TSDSS functions as an offline data analysis system during I&T (integration and test) and mission operations phases. After raw data are downloaded from an instrument, TSDSS ingests the data files, parses, converts telemetry to engineering units, and applies advanced algorithms to produce science level 0, 1, and 2 data products. Meanwhile, it automatically schedules upload of the raw data to a remote server and archives all intermediate and final values in a MySQL database in time order. All data saved in the system can be straightforwardly retrieved, exported, and migrated. Using TSDSS s interactive data visualization tool, a user can conveniently choose any combination and mathematical computation of interesting telemetry points from a large range of time periods (life cycle of mission ground data and mission operations testing), and display a graphical and statistical view of the data. With this graphical user interface (GUI), the data queried graphs can be exported and saved in multiple formats. This GUI is especially useful in trending data analysis, debugging anomalies, and advanced data analysis. At the request of the user, mission-specific instrument performance assessment reports can be generated with a simple click of a button on the GUI. From instrument level to observatory level, the TSDSS has been operating supporting

  9. Software V ampersand V methods for digital plant protection system

    International Nuclear Information System (INIS)

    Kim, Hung-Jun; Han, Jai-Bok; Chun, Chong-Son; Kim, Sung; Kim, Kern-Joong.

    1997-01-01

    Careful thought must be given to software design in the development of digital based systems that play a critical role in the successful operation of nuclear power plants. To evaluate the software verification and validation methods as well as to verify its system performance capabilities for the upgrade instrumentation and control system in the Korean future nuclear power plants, the prototype Digital Plant, Protection System (DPPS) based on the Programmable Logic Controller (PLC) has been constructed. The system design description and features are briefly presented, and the software design and software verification and validation methods are focused. 6 refs., 2 figs

  10. A control system verifier using automated reasoning software

    International Nuclear Information System (INIS)

    Smith, D.E.; Seeman, S.E.

    1985-08-01

    An on-line, automated reasoning software system for verifying the actions of other software or human control systems has been developed. It was demonstrated by verifying the actions of an automated procedure generation system. The verifier uses an interactive theorem prover as its inference engine with the rules included as logical axioms. Operation of the verifier is generally transparent except when the verifier disagrees with the actions of the monitored software. Testing with an automated procedure generation system demonstrates the successful application of automated reasoning software for verification of logical actions in a diverse, redundant manner. A higher degree of confidence may be placed in the verified actions of the combined system

  11. Software architecture standard for simulation virtual machine, version 2.0

    Science.gov (United States)

    Sturtevant, Robert; Wessale, William

    1994-01-01

    The Simulation Virtual Machine (SBM) is an Ada architecture which eases the effort involved in the real-time software maintenance and sustaining engineering. The Software Architecture Standard defines the infrastructure which all the simulation models are built from. SVM was developed for and used in the Space Station Verification and Training Facility.

  12. Software for the international linear collider: Simulation and ...

    Indian Academy of Sciences (India)

    Software plays an increasingly important role already in the early stages of a large project like the ILC. In international collaboration a data format for the ILC detector and physics studies has been developed. Building upon this software frameworks are made available which ease the event reconstruction and analysis.

  13. Experiences with Integrating Simulation into a Software Engineering Curriculum

    Science.gov (United States)

    Bollin, Andreas; Hochmuller, Elke; Mittermeir, Roland; Samuelis, Ladislav

    2012-01-01

    Software Engineering education must account for a broad spectrum of knowledge and skills software engineers will be required to apply throughout their professional life. Covering all the topics in depth within a university setting is infeasible due to curricular constraints as well as due to the inherent differences between educational…

  14. Modelling and transient simulation of water flow in pipelines using WANDA Transient software

    Directory of Open Access Journals (Sweden)

    P.U. Akpan

    2017-09-01

    Full Text Available Pressure transients in conduits such as pipelines are unsteady flow conditions caused by a sudden change in the flow velocity. These conditions might cause damage to the pipelines and its fittings if the extreme pressure (high or low is experienced within the pipeline. In order to avoid this occurrence, engineers usually carry out pressure transient analysis in the hydraulic design phase of pipeline network systems. Modelling and simulation of transients in pipelines is an acceptable and cost effective method of assessing this problem and finding technical solutions. This research predicts the pressure surge for different flow conditions in two different pipeline systems using WANDA Transient simulation software. Computer models were set-up in WANDA Transient for two different systems namely; the Graze experiment (miniature system and a simple main water riser system based on some initial laboratory data and system parameters. The initial laboratory data and system parameters were used for all the simulations. Results obtained from the computer model simulations compared favourably with the experimental results at Polytropic index of 1.2.

  15. Software Tools to Support the Assessment of System Health

    Science.gov (United States)

    Melcher, Kevin J.

    2013-01-01

    sensors that optimally meet the performance goals and the constraints. It identifies optimal sensor suite solutions by utilizing a merit (i.e., cost) function with one of several available optimization approaches. As part of its analysis, S4 can expose fault conditions that are difficult to diagnose due to an incomplete diagnostic philosophy and/or a lack of sensors. S4 was originally developed and applied to liquid rocket engines. It was subsequently used to study the optimized selection of sensors for a simulation ]based aircraft engine diagnostic system. The ETA Tool is a software ]based analysis tool that augments the testability analysis and reporting capabilities of a commercial ]off ]the ]shelf (COTS) package. An initial diagnostic assessment is performed by the COTS software using a user ]developed, qualitative, directed ]graph model of the system being analyzed. The ETA Tool accesses system design information captured within the model and the associated testability analysis output to create a series of six reports for various system engineering needs. These reports are highlighted in the presentation. The ETA Tool was developed by NASA to support the verification of fault management requirements early in the Launch Vehicle process. Due to their early development during the design process, the TEAMS ]based diagnostic model and the ETA Tool were able to positively influence the system design by highlighting gaps in failure detection, fault isolation, and failure recovery.

  16. Software Engineering Laboratory (SEL) data base reporting software user's guide and system description. Volume 1: Introduction and user's guide

    Science.gov (United States)

    1983-01-01

    Reporting software programs provide formatted listings and summary reports of the Software Engineering Laboratory (SEL) data base contents. The operating procedures and system information for 18 different reporting software programs are described. Sample output reports from each program are provided.

  17. Security Information System Digital Simulation

    OpenAIRE

    Tao Kuang; Shanhong Zhu

    2015-01-01

    The study built a simulation model for the study of food security information system relay protection. MATLAB-based simulation technology can support the analysis and design of food security information systems. As an example, the food security information system fault simulation, zero-sequence current protection simulation and transformer differential protection simulation are presented in this study. The case studies show that the simulation of food security information system relay protect...

  18. Analyzing Software Requirements Errors in Safety-Critical, Embedded Systems

    Science.gov (United States)

    Lutz, Robyn R.

    1993-01-01

    This paper analyzes the root causes of safety-related software errors in safety-critical, embedded systems. The results show that software errors identified as potentially hazardous to the system tend to be produced by different error mechanisms than non- safety-related software errors. Safety-related software errors are shown to arise most commonly from (1) discrepancies between the documented requirements specifications and the requirements needed for correct functioning of the system and (2) misunderstandings of the software's interface with the rest of the system. The paper uses these results to identify methods by which requirements errors can be prevented. The goal is to reduce safety-related software errors and to enhance the safety of complex, embedded systems.

  19. Flight test of a resident backup software system

    Science.gov (United States)

    Deets, Dwain A.; Lock, Wilton P.; Megna, Vincent A.

    1987-01-01

    A new fault-tolerant system software concept employing the primary digital computers as host for the backup software portion has been implemented and flight tested in the F-8 digital fly-by-wire airplane. The system was implemented in such a way that essentially no transients occurred in transferring from primary to backup software. This was accomplished without a significant increase in the complexity of the backup software. The primary digital system was frame synchronized, which provided several advantages in implementing the resident backup software system. Since the time of the flight tests, two other flight vehicle programs have made a commitment to incorporate resident backup software similar in nature to the system described here.

  20. SWEPP Gamma-Ray Spectrometer System software design description

    International Nuclear Information System (INIS)

    Femec, D.A.; Killian, E.W.

    1994-08-01

    To assist in the characterization of the radiological contents of contract-handled waste containers at the Stored Waste Examination Pilot Plant (SWEPP), the SWEPP Gamma-Ray Spectrometer (SGRS) System has been developed by the Radiation Measurements and Development Unit of the Idaho National Engineering Laboratory. The SGRS system software controls turntable and detector system activities. In addition to determining the concentrations of gamma-ray-emitting radionuclides, this software also calculates attenuation-corrected isotopic mass ratios of-specific interest. This document describes the software design for the data acquisition and analysis software associated with the SGRS system

  1. SWEPP Gamma-Ray Spectrometer System software design description

    Energy Technology Data Exchange (ETDEWEB)

    Femec, D.A.; Killian, E.W.

    1994-08-01

    To assist in the characterization of the radiological contents of contract-handled waste containers at the Stored Waste Examination Pilot Plant (SWEPP), the SWEPP Gamma-Ray Spectrometer (SGRS) System has been developed by the Radiation Measurements and Development Unit of the Idaho National Engineering Laboratory. The SGRS system software controls turntable and detector system activities. In addition to determining the concentrations of gamma-ray-emitting radionuclides, this software also calculates attenuation-corrected isotopic mass ratios of-specific interest. This document describes the software design for the data acquisition and analysis software associated with the SGRS system.

  2. Software Defined Common Processing System (SDCPS), Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Coherent Logix, Incorporated (CLX) proposes the development of a Software Defined Common Processing System (SDCPS) that leverages the inherent advantages of an...

  3. A Review of Freely Available Quantum Computer Simulation Software

    OpenAIRE

    Brandhorst-Satzkorn, Johan

    2012-01-01

    A study has been made of a few different freely available Quantum Computer simulators. All the simulators tested are available online on their respective websites. A number of tests have been performed to compare the different simulators against each other. Some untested simulators of various programming languages are included to show the diversity of the quantum computer simulator applications. The conclusion of the review is that LibQuantum is the best of the simulators tested because of ea...

  4. Fluctuating Finite Element Analysis (FFEA: A continuum mechanics software tool for mesoscale simulation of biomolecules.

    Directory of Open Access Journals (Sweden)

    Albert Solernou

    2018-03-01

    Full Text Available Fluctuating Finite Element Analysis (FFEA is a software package designed to perform continuum mechanics simulations of proteins and other globular macromolecules. It combines conventional finite element methods with stochastic thermal noise, and is appropriate for simulations of large proteins and protein complexes at the mesoscale (length-scales in the range of 5 nm to 1 μm, where there is currently a paucity of modelling tools. It requires 3D volumetric information as input, which can be low resolution structural information such as cryo-electron tomography (cryo-ET maps or much higher resolution atomistic co-ordinates from which volumetric information can be extracted. In this article we introduce our open source software package for performing FFEA simulations which we have released under a GPLv3 license. The software package includes a C ++ implementation of FFEA, together with tools to assist the user to set up the system from Electron Microscopy Data Bank (EMDB or Protein Data Bank (PDB data files. We also provide a PyMOL plugin to perform basic visualisation and additional Python tools for the analysis of FFEA simulation trajectories. This manuscript provides a basic background to the FFEA method, describing the implementation of the core mechanical model and how intermolecular interactions and the solvent environment are included within this framework. We provide prospective FFEA users with a practical overview of how to set up an FFEA simulation with reference to our publicly available online tutorials and manuals that accompany this first release of the package.

  5. User and system considerations for the TCSTEK software library

    International Nuclear Information System (INIS)

    Gray, W.H.

    1979-08-01

    This report documents the idiosyncrasies of the Tektronix PLOT 10 Terminal Control System level 3.3 software as it currently exists on the ORNL Fusion Energy Division DECsystem-10 computer. It is intended to serve as a reference for future Terminal Control System updates in order that continuity between releases of Terminal Control System PLOT 10 software may be maintained

  6. 36 CFR 1194.21 - Software applications and operating systems.

    Science.gov (United States)

    2010-07-01

    ... operating systems. 1194.21 Section 1194.21 Parks, Forests, and Public Property ARCHITECTURAL AND... Standards § 1194.21 Software applications and operating systems. (a) When software is designed to run on a... shall not disrupt or disable activated features of any operating system that are identified as...

  7. User and system considerations for the TCSTEK software library

    Energy Technology Data Exchange (ETDEWEB)

    Gray, W.H.

    1979-08-01

    This report documents the idiosyncrasies of the Tektronix PLOT 10 Terminal Control System level 3.3 software as it currently exists on the ORNL Fusion Energy Division DECsystem-10 computer. It is intended to serve as a reference for future Terminal Control System updates in order that continuity between releases of Terminal Control System PLOT 10 software may be maintained.

  8. Digital image processing software system using an array processor

    International Nuclear Information System (INIS)

    Sherwood, R.J.; Portnoff, M.R.; Journeay, C.H.; Twogood, R.E.

    1981-01-01

    A versatile array processor-based system for general-purpose image processing was developed. At the heart of this system is an extensive, flexible software package that incorporates the array processor for effective interactive image processing. The software system is described in detail, and its application to a diverse set of applications at LLNL is briefly discussed. 4 figures, 1 table

  9. SORPAS – The Professional Software for Simulation of Resistance Welding

    DEFF Research Database (Denmark)

    Zhang, Wenqi

    2002-01-01

    and easily operate and utilize the software. With the user-friendly facilities for flexible geometric design of work pieces and electrodes as well as process parameter settings similar to real machine parameter settings, the software has been readily applied in industry for supporting product development...... applied in industries including automotive, electronics and other metal processing industries as well as welding equipment manufacturers....... directly usable by engineers and technicians in industry, all of the important parameters in resistance welding are considered and automatically implemented into the software. With the specially designed graphic user interface for Windows, engineers (even without prior knowledge of FEM) can quickly learn...

  10. Software reliability growth model for safety systems of nuclear reactor

    International Nuclear Information System (INIS)

    Thirugnana Murthy, D.; Murali, N.; Sridevi, T.; Satya Murty, S.A.V.; Velusamy, K.

    2014-01-01

    The demand for complex software systems has increased more rapidly than the ability to design, implement, test, and maintain them, and the reliability of software systems has become a major concern for our, modern society.Software failures have impaired several high visibility programs in space, telecommunications, defense and health industries. Besides the costs involved, it setback the projects. The ways of quantifying it and using it for improvement and control of the software development and maintenance process. This paper discusses need for systematic approaches for measuring and assuring software reliability which is a major share of project development resources. It covers the reliability models with the concern on 'Reliability Growth'. It includes data collection on reliability, statistical estimation and prediction, metrics and attributes of product architecture, design, software development, and the operational environment. Besides its use for operational decisions like deployment, it includes guiding software architecture, development, testing and verification and validation. (author)

  11. Compiling software for a hierarchical distributed processing system

    Science.gov (United States)

    Archer, Charles J; Blocksome, Michael A; Ratterman, Joseph D; Smith, Brian E

    2013-12-31

    Compiling software for a hierarchical distributed processing system including providing to one or more compiling nodes software to be compiled, wherein at least a portion of the software to be compiled is to be executed by one or more nodes; compiling, by the compiling node, the software; maintaining, by the compiling node, any compiled software to be executed on the compiling node; selecting, by the compiling node, one or more nodes in a next tier of the hierarchy of the distributed processing system in dependence upon whether any compiled software is for the selected node or the selected node's descendents; sending to the selected node only the compiled software to be executed by the selected node or selected node's descendent.

  12. Software-in-the-loop simulation of a quadcopter portion for hybrid aircraft control

    Science.gov (United States)

    Mansoor, Shoaib; Saedan, Mana

    2018-01-01

    In this paper, we present the design of the software-in-the-loop simulation framework for a quadcopter that is incorporated in our hybrid aircraft. The hybrid aircraft comprises a quad-copter and a fixed wing with one forward thrust rotor. We need to develop a split control system that utilizes a typical quadcopter controller to control four motors/propellers and a supervisor controller to control a forward thrust rotor. The supervisor controller shall take feedback signals from the quadcopter and will command the fifth rotor for stabilizing the hybrid aircraft and resolves problems like thrust saturation. The simulation simulates the control algorithm and verifies the quadcopter’s behavior using MATLAB and Simulink together. Achieving these results, we come to know how our hybrid controller will be implemented, what results to expect once the forward thrust rotor is attached to the quadcopter. The software-in-the-loop simulation of a quadcopter is one of the most effective methods for verifying overall control performance and safety of the hybrid aircraft before actual hardware implementation and flight test.

  13. A fault-tolerant software strategy for digital systems

    Science.gov (United States)

    Hitt, E. F.; Webb, J. J.

    1984-01-01

    Techniques developed for producing fault-tolerant software are described. Tolerance is required because of the impossibility of defining fault-free software. Faults are caused by humans and can appear anywhere in the software life cycle. Tolerance is effected through error detection, damage assessment, recovery, and fault treatment, followed by return of the system to service. Multiversion software comprises two or more versions of the software yielding solutions which are examined by a decision algorithm. Errors can also be detected by extrapolation from previous results or by the acceptability of results. Violations of timing specifications can reveal errors, or the system can roll back to an error-free state when a defect is detected. The software, when used in flight control systems, must not impinge on time-critical responses. Efforts are still needed to reduce the costs of developing the fault-tolerant systems.

  14. SIMULATION AS A TOOL FOR PROCESS OPTIMIZATION OF LOGISTIC SYSTEMS

    Directory of Open Access Journals (Sweden)

    Radko Popovič

    2015-09-01

    Full Text Available The paper deals with the simulation of the production processes, especially module of Siemens Tecnomatix software. Tecnomatix Process Simulate is designed for building new or modifying existing production processes. The simulation created in this software has a posibility for fast testing of planned changes or improvements of the production processes. On the base of simulation you can imagine the future picture of the real production system. 3D Simulation can reflects the actual status and conditions on the running system and of course, after some improvements, it can show the possible figure of the production system.

  15. Model-driven dependability assessment of software systems

    CERN Document Server

    Bernardi, Simona; Petriu, Dorina C

    2013-01-01

    In this book, the authors present cutting-edge model-driven techniques for modeling and analysis of software dependability. Most of them are based on the use of UML as software specification language. From the software system specification point of view, such techniques exploit the standard extension mechanisms of UML (i.e., UML profiling). UML profiles enable software engineers to add non-functional properties to the software model, in addition to the functional ones. The authors detail the state of the art on UML profile proposals for dependability specification and rigorously describe the t

  16. Design of simulation builder software to support the enterprise modeling and simulation task of the AMTEX program

    Energy Technology Data Exchange (ETDEWEB)

    Nolan, M.; Lamont, A.; Chang, L.

    1995-12-12

    This document describes the implementation of the Simulation Builder developed as part of the Enterprise Modeling and Simulation (EM&S) portion of the Demand Activated Manufacturing Architecture (DAMA) project. The Simulation Builder software allows users to develop simulation models using pre-defined modules from a library. The Simulation Builder provides the machinery to allow the modules to link together and communicate information during the simulation run. This report describes the basic capabilities and structure of the Simulation Builder to assist a user in reviewing and using the code. It also describes the basic steps to follow when developing modules to take advantage of the capabilities provided by the Simulation Builder. The Simulation Builder software is written in C++. The discussion in this report assumes a sound understanding of the C++ language. Although this report describes the steps to follow when using the Simulation Builder, it is not intended to be a tutorial for a user unfamiliar with C++.

  17. software for natural gas pipeline design and simulation

    African Journals Online (AJOL)

    Global Journal

    2017-01-17

    Jan 17, 2017 ... investment and operating cost required for natural gas pipeline transmission ... In the early development of the natural gas transmission industry, pressures were low and ..... The software has an error control capability in.

  18. Storage system software solutions for high-end user needs

    Science.gov (United States)

    Hogan, Carole B.

    1992-01-01

    Today's high-end storage user is one that requires rapid access to a reliable terabyte-capacity storage system running in a distributed environment. This paper discusses conventional storage system software and concludes that this software, designed for other purposes, cannot meet high-end storage requirements. The paper also reviews the philosophy and design of evolving storage system software. It concludes that this new software, designed with high-end requirements in mind, provides the potential for solving not only the storage needs of today but those of the foreseeable future as well.

  19. Harmonic Domain Modeling of a Distribution System Using the DIgSILENT PowerFactory Software

    DEFF Research Database (Denmark)

    Wasilewski, J.; Wiechowski, Wojciech Tomasz; Bak, Claus Leth

    The first part of this paper presents the comparison between two models of distribution system created in computer simulation software PowerFactory (PF). Model A is an exciting simplified equivalent model of the distribution system used by Transmission System Operator (TSO) Eltra for balenced load...

  20. Training Requirements and Information Management System. Software user guide

    Energy Technology Data Exchange (ETDEWEB)

    Cillan, T.F.; Hodgson, M.A.

    1992-05-01

    This is the software user`s guide for the Training Requirements and Information Management System. This guide defines and describes the software operating procedures as they apply to the end user of the software program. This guide is intended as a reference tool for the user who already has an indepth knowledge of the Training Requirements and Information Management System functions and data reporting requirement.

  1. Advanced information processing system: Input/output network management software

    Science.gov (United States)

    Nagle, Gail; Alger, Linda; Kemp, Alexander

    1988-01-01

    The purpose of this document is to provide the software requirements and specifications for the Input/Output Network Management Services for the Advanced Information Processing System. This introduction and overview section is provided to briefly outline the overall architecture and software requirements of the AIPS system before discussing the details of the design requirements and specifications of the AIPS I/O Network Management software. A brief overview of the AIPS architecture followed by a more detailed description of the network architecture.

  2. Modernization of tank floor scanning system (TAFLOSS) software

    International Nuclear Information System (INIS)

    Mohd Fitri Abdul Rahman; Jaafar Abdullah; Susan Maria Sipaun

    2002-01-01

    Tank Floor Scanning System (TAFLOSS) is a portable nucleonic device based on the scattering and moderation phenomena of neutrons. TAFLOSS, which was developed by MINT, can precisely and non-destructively measure the gap and hydrogen content in the foundation of a gigantic industrial tank in a practical and cost-effective manner. In recording and analysing measured data, three different computer software were used. In analysing the initial data, a Disk Operating System (DOS) based software called MesTank 3.0 have been developed. The system also used commercial software such as Table Curve 2D and SURFER for graphics purposes. Table Curve 2D was used to plot and evaluate curve fitting, whereas SURFER software used to draw contours. It is not user friendly and time consuming to switch from a software to another software for different tasks of this system. Therefore, the main objective of the project is to develop new user-friendly software that combined the old and commercial software into a single package. The computer programming language that was used to develop the software is Microsoft Visual C++ ver. 6.0. The process of developing this software involved complex mathematical calculation, curve fitting and contour plot. This paper describes the initial development of a computer programme for analysing the initial data and plotting exponential curve fitting. (Author)

  3. Bega - Android-Based Beergame Simulation Software for Interactive Training and Innovation

    Science.gov (United States)

    Lestyánszka Škůrková, Katarína; Szander, Norina

    2013-12-01

    The supply chain management challenges and inventory holding problems can easily be demonstrated by the widely known BeerGame simulation. In the Szabó-Szoba R&D Laboratory, we developed an android-based software application for tablets and smart phones for the purpose of having an adaptable, entertaining and effective program which can provide a real life experience to the participants about the nature of the bullwhip effect. Having an appropriate and comprehensive performance measurement system with the critical parameters and KPIs is inevitable for finding the right solutions - We used four perspectives of the Balanced Scorecard method. The innovative force of our research is based on the trainings: the discussion on outcomes and the team learning. The purpose of the current development is to build a new feature in the software: an artificial client can substitute one or more players in the supply chain, which makes decisions by using genetic algorithms.

  4. Computational simulation of concurrent engineering for aerospace propulsion systems

    Science.gov (United States)

    Chamis, C. C.; Singhal, S. N.

    1992-01-01

    Results are summarized of an investigation to assess the infrastructure available and the technology readiness in order to develop computational simulation methods/software for concurrent engineering. These results demonstrate that development of computational simulations methods for concurrent engineering is timely. Extensive infrastructure, in terms of multi-discipline simulation, component-specific simulation, system simulators, fabrication process simulation, and simulation of uncertainties - fundamental in developing such methods, is available. An approach is recommended which can be used to develop computational simulation methods for concurrent engineering for propulsion systems and systems in general. Benefits and facets needing early attention in the development are outlined.

  5. Computational simulation for concurrent engineering of aerospace propulsion systems

    Science.gov (United States)

    Chamis, C. C.; Singhal, S. N.

    1993-01-01

    Results are summarized for an investigation to assess the infrastructure available and the technology readiness in order to develop computational simulation methods/software for concurrent engineering. These results demonstrate that development of computational simulation methods for concurrent engineering is timely. Extensive infrastructure, in terms of multi-discipline simulation, component-specific simulation, system simulators, fabrication process simulation, and simulation of uncertainties--fundamental to develop such methods, is available. An approach is recommended which can be used to develop computational simulation methods for concurrent engineering of propulsion systems and systems in general. Benefits and issues needing early attention in the development are outlined.

  6. A Visual Basic simulation software tool for performance analysis of a membrane-based advanced water treatment plant.

    Science.gov (United States)

    Pal, P; Kumar, R; Srivastava, N; Chaudhuri, J

    2014-02-01

    A Visual Basic simulation software (WATTPPA) has been developed to analyse the performance of an advanced wastewater treatment plant. This user-friendly and menu-driven software is based on the dynamic mathematical model for an industrial wastewater treatment scheme that integrates chemical, biological and membrane-based unit operations. The software-predicted results corroborate very well with the experimental findings as indicated in the overall correlation coefficient of the order of 0.99. The software permits pre-analysis and manipulation of input data, helps in optimization and exhibits performance of an integrated plant visually on a graphical platform. It allows quick performance analysis of the whole system as well as the individual units. The software first of its kind in its domain and in the well-known Microsoft Excel environment is likely to be very useful in successful design, optimization and operation of an advanced hybrid treatment plant for hazardous wastewater.

  7. A Project Management Approach to Using Simulation for Cost Estimation on Large, Complex Software Development Projects

    Science.gov (United States)

    Mizell, Carolyn; Malone, Linda

    2007-01-01

    It is very difficult for project managers to develop accurate cost and schedule estimates for large, complex software development projects. None of the approaches or tools available today can estimate the true cost of software with any high degree of accuracy early in a project. This paper provides an approach that utilizes a software development process simulation model that considers and conveys the level of uncertainty that exists when developing an initial estimate. A NASA project will be analyzed using simulation and data from the Software Engineering Laboratory to show the benefits of such an approach.

  8. ISWHM: Tools and Techniques for Software and System Health Management

    Science.gov (United States)

    Schumann, Johann; Mengshoel, Ole J.; Darwiche, Adnan

    2010-01-01

    This presentation presents status and results of research on Software Health Management done within the NRA "ISWHM: Tools and Techniques for Software and System Health Management." Topics include: Ingredients of a Guidance, Navigation, and Control System (GN and C); Selected GN and C Testbed example; Health Management of major ingredients; ISWHM testbed architecture; and Conclusions and next Steps.

  9. Software for MR imaging system VISTA-E50

    International Nuclear Information System (INIS)

    Nakatao, Shirou; Iino, Mitsutoshi; Fukuda, Kazuhiko

    1989-01-01

    VISTA-E50 has the advantages of high-quality imaging, fast scanning, high patient throughput and easy operation featured by AI (artificial intelligence) technologies, as well as merits of compact, light-weight, space- and energy-saving system. This paper presents system software and clinical application software of VISTA-E50, especially for each function and advantage. (author)

  10. Environmental Control System Software & Hardware Development

    Science.gov (United States)

    Vargas, Daniel Eduardo

    2017-01-01

    ECS hardware: (1) Provides controlled purge to SLS Rocket and Orion spacecraft. (2) Provide mission-focused engineering products and services. ECS software: (1) NASA requires Compact Unique Identifiers (CUIs); fixed-length identifier used to identify information items. (2) CUI structure; composed of nine semantic fields that aid the user in recognizing its purpose.

  11. New control system: ADA softwares organization

    International Nuclear Information System (INIS)

    David, L.

    1992-01-01

    On VAX/VMS, ADA compiler is integrated in a workshop of ACS software engineering which allows a coherent development by control of source and executable programs, by separation of applications in various levels of visibility and by management of existing links between different modules of a same application. (A.B.)

  12. Artificial intelligence and expert systems in-flight software testing

    Science.gov (United States)

    Demasie, M. P.; Muratore, J. F.

    1991-01-01

    The authors discuss the introduction of advanced information systems technologies such as artificial intelligence, expert systems, and advanced human-computer interfaces directly into Space Shuttle software engineering. The reconfiguration automation project (RAP) was initiated to coordinate this move towards 1990s software technology. The idea behind RAP is to automate several phases of the flight software testing procedure and to introduce AI and ES into space shuttle flight software testing. In the first phase of RAP, conventional tools to automate regression testing have already been developed or acquired. There are currently three tools in use.

  13. An Agent Based Software Approach towards Building Complex Systems

    Directory of Open Access Journals (Sweden)

    Latika Kharb

    2015-08-01

    Full Text Available Agent-oriented techniques represent an exciting new means of analyzing, designing and building complex software systems. They have the potential to significantly improve current practice in software engineering and to extend the range of applications that can feasibly be tackled. Yet, to date, there have been few serious attempts to cast agent systems as a software engineering paradigm. This paper seeks to rectify this omission. Specifically, points to be argued include:firstly, the conceptual apparatus of agent-oriented systems is well-suited to building software solutions for complex systems and secondly, agent-oriented approaches represent a genuine advance over the current state of the art for engineering complex systems. Following on from this view, the major issues raised by adopting an agentoriented approach to software engineering are highlighted and discussed in this paper.

  14. A PC-based discrete tomography imaging software system for assaying radioactive waste containers

    International Nuclear Information System (INIS)

    Palacios, J.C.; Longoria, L.C.; Santos, J.; Perry, R.T.

    2003-01-01

    A PC-based discrete tomography imaging software system for assaying radioactive waste containers for use in facilities in Mexico has been developed. The software system consists of three modules: (i) for reconstruction transmission tomography, (ii) for reconstruction emission tomography, and (iii) for simulation tomography. The Simulation Module is an interactive computer program that is used to create simulated databases for input to the Reconstruction Modules. These databases may be used in the absence of physical measurements to insure that the tomographic theoretical models are valid and that the coding accurately describes these models. Simulation may also be used to determine the detection limits of the reconstruction methodology. A description of the system, the theory, and a demonstration of the systems capabilities is provided in the paper. The hardware for this system is currently under development

  15. The development of WIPPVENT, a windows based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    McDaniel, K.H.

    1995-01-01

    An interactive mine ventilation simulation software program (WIPPVENT) was developed at the Waste Isolation Pilot Plant (WIPP). The WIPP is a US Department of Energy (DOE) research and development project located near Carlsbad, New Mexico. The facility is designed to provide a permanent, safe underground disposal of US defense generated transuranic waste in bedded salt. In addition to it's regular functions, the underground ventilation system is engineered to prevent the uncontrolled spread of radioactive materials in the unlikely event of a release. To enhance the operability system, Westinghouse Electric Corporation has developed an interactive mine ventilation simulation software program (WIPPVENT). While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC (copyright 1991 Mine Ventilation Services, Inc.), the user interface has been completely rewritten as a Windows reg-sign application and screen graphics have been added. WIPPVENT is designed to interact with the WIPP ventilation monitoring systems through the site wide Central Monitoring System

  16. Advanced transport operating system software upgrade: Flight management/flight controls software description

    Science.gov (United States)

    Clinedinst, Winston C.; Debure, Kelly R.; Dickson, Richard W.; Heaphy, William J.; Parks, Mark A.; Slominski, Christopher J.; Wolverton, David A.

    1988-01-01

    The Flight Management/Flight Controls (FM/FC) software for the Norden 2 (PDP-11/70M) computer installed on the NASA 737 aircraft is described. The software computes the navigation position estimates, guidance commands, those commands to be issued to the control surfaces to direct the aircraft in flight based on the modes selected on the Advanced Guidance Control System (AGSC) mode panel, and the flight path selected via the Navigation Control/Display Unit (NCDU).

  17. The software design of area γ radiation monitoring system

    International Nuclear Information System (INIS)

    Song Chenxin; Deng Changming; Cheng Chang; Ren Yi; Meng Dan; Liu Yun

    2007-01-01

    This paper main introduction the system structure, software architecture, design ideas of the area γ radiation monitoring system. Detailed introduction some programming technology about the computer communication with the local display unit. (authors)

  18. The software design of area γ radiation monitoring system

    International Nuclear Information System (INIS)

    Song Chenxin; Deng Changming; Cheng Chang; Ren Yi; Meng Dan; Liu Yun

    2008-01-01

    This paper main introduction the system structure, software architecture, design ideas of the area γ radiation monitoring system. Detailed introduction some programming technology about the computer communication with the local display unit. (authors)

  19. Research and Development on Food Nutrition Statistical Analysis Software System

    OpenAIRE

    Du Li; Ke Yun

    2013-01-01

    Designing and developing a set of food nutrition component statistical analysis software can realize the automation of nutrition calculation, improve the nutrition processional professional’s working efficiency and achieve the informatization of the nutrition propaganda and education. In the software development process, the software engineering method and database technology are used to calculate the human daily nutritional intake and the intelligent system is used to evaluate the user’s hea...

  20. Statistical reliability assessment of software-based systems

    International Nuclear Information System (INIS)

    Korhonen, J.; Pulkkinen, U.; Haapanen, P.

    1997-01-01

    Plant vendors nowadays propose software-based systems even for the most critical safety functions. The reliability estimation of safety critical software-based systems is difficult since the conventional modeling techniques do not necessarily apply to the analysis of these systems, and the quantification seems to be impossible. Due to lack of operational experience and due to the nature of software faults, the conventional reliability estimation methods can not be applied. New methods are therefore needed for the safety assessment of software-based systems. In the research project Programmable automation systems in nuclear power plants (OHA), financed together by the Finnish Centre for Radiation and Nuclear Safety (STUK), the Ministry of Trade and Industry and the Technical Research Centre of Finland (VTT), various safety assessment methods and tools for software based systems are developed and evaluated. This volume in the OHA-report series deals with the statistical reliability assessment of software based systems on the basis of dynamic test results and qualitative evidence from the system design process. Other reports to be published later on in OHA-report series will handle the diversity requirements in safety critical software-based systems, generation of test data from operational profiles and handling of programmable automation in plant PSA-studies. (orig.) (25 refs.)

  1. Testing digital safety system software with a testability measure based on a software fault tree

    International Nuclear Information System (INIS)

    Sohn, Se Do; Hyun Seong, Poong

    2006-01-01

    Using predeveloped software, a digital safety system is designed that meets the quality standards of a safety system. To demonstrate the quality, the design process and operating history of the product are reviewed along with configuration management practices. The application software of the safety system is developed in accordance with the planned life cycle. Testing, which is a major phase that takes a significant time in the overall life cycle, can be optimized if the testability of the software can be evaluated. The proposed testability measure of the software is based on the entropy of the importance of basic statements and the failure probability from a software fault tree. To calculate testability, a fault tree is used in the analysis of a source code. With a quantitative measure of testability, testing can be optimized. The proposed testability can also be used to demonstrate whether the test cases based on uniform partitions, such as branch coverage criteria, result in homogeneous partitions that is known to be more effective than random testing. In this paper, the testability measure is calculated for the modules of a nuclear power plant's safety software. The module testing with branch coverage criteria required fewer test cases if the module has higher testability. The result shows that the testability measure can be used to evaluate whether partitions have homogeneous characteristics

  2. Software reliability and safety in nuclear reactor protection systems

    International Nuclear Information System (INIS)

    Lawrence, J.D.

    1993-11-01

    Planning the development, use and regulation of computer systems in nuclear reactor protection systems in such a way as to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Computer Safety and Reliability Group, Lawrence Livermore that investigates different aspects of computer software in reactor National Laboratory, that investigates different aspects of computer software in reactor protection systems. There are two central themes in the report, First, software considerations cannot be fully understood in isolation from computer hardware and application considerations. Second, the process of engineering reliability and safety into a computer system requires activities to be carried out throughout the software life cycle. The report discusses the many activities that can be carried out during the software life cycle to improve the safety and reliability of the resulting product. The viewpoint is primarily that of the assessor, or auditor

  3. Software reliability and safety in nuclear reactor protection systems

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence, J.D. [Lawrence Livermore National Lab., CA (United States)

    1993-11-01

    Planning the development, use and regulation of computer systems in nuclear reactor protection systems in such a way as to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Computer Safety and Reliability Group, Lawrence Livermore that investigates different aspects of computer software in reactor National Laboratory, that investigates different aspects of computer software in reactor protection systems. There are two central themes in the report, First, software considerations cannot be fully understood in isolation from computer hardware and application considerations. Second, the process of engineering reliability and safety into a computer system requires activities to be carried out throughout the software life cycle. The report discusses the many activities that can be carried out during the software life cycle to improve the safety and reliability of the resulting product. The viewpoint is primarily that of the assessor, or auditor.

  4. A real-time computer simulation of nuclear simulator software using standard PC hardware and linux environments

    International Nuclear Information System (INIS)

    Cha, K. H.; Kweon, K. C.

    2001-01-01

    A feasibility study, which standard PC hardware and Real-Time Linux are applied to real-time computer simulation of software for a nuclear simulator, is presented in this paper. The feasibility prototype was established with the existing software in the Compact Nuclear Simulator (CNS). Throughout the real-time implementation in the feasibility prototype, we has identified that the approach can enable the computer-based predictive simulation to be approached, due to both the remarkable improvement in real-time performance and the less efforts for real-time implementation under standard PC hardware and Real-Time Linux envrionments

  5. Algebraic software analysis and embedded simulation of a driving robot

    NARCIS (Netherlands)

    Merkx, L.L.F.; Duringhof, H.M.; Cuijpers, P.J.L.

    2007-01-01

    At TNO Automotive the Generic Driving Actuator (GDA) is developed. The GDA is a device capable of driving a vehicle fully automatically using the same interface as a human driver does. In this paper, the design of the GDA is discussed. The software and hardware of the GDA and its effect on vehicle

  6. Contribution to the development of a simulation software ...

    African Journals Online (AJOL)

    The present work is to develop software to predict the value yield and the distribution coefficient in the process of liquid-liquid extraction of components of a mixture, from mathematical models expressing these entities, based on equations equilibrium between liquid-liquid phases, and predict the conditions under which the ...

  7. Advances in model-based software for simulating ultrasonic immersion inspections of metal components

    Science.gov (United States)

    Chiou, Chien-Ping; Margetan, Frank J.; Taylor, Jared L.; Engle, Brady J.; Roberts, Ronald A.

    2018-04-01

    Under the sponsorship of the National Science Foundation's Industry/University Cooperative Research Center at ISU, an effort was initiated in 2015 to repackage existing research-grade software into user-friendly tools for the rapid estimation of signal-to-noise ratio (SNR) for ultrasonic inspections of metals. The software combines: (1) a Python-based graphical user interface for specifying an inspection scenario and displaying results; and (2) a Fortran-based engine for computing defect signals and backscattered grain noise characteristics. The later makes use the Thompson-Gray measurement model for the response from an internal defect, and the Thompson-Margetan independent scatterer model for backscattered grain noise. This paper, the third in the series [1-2], provides an overview of the ongoing modeling effort with emphasis on recent developments. These include the ability to: (1) treat microstructures where grain size, shape and tilt relative to the incident sound direction can all vary with depth; and (2) simulate C-scans of defect signals in the presence of backscattered grain noise. The simulation software can now treat both normal and oblique-incidence immersion inspections of curved metal components. Both longitudinal and shear-wave inspections are treated. The model transducer can either be planar, spherically-focused, or bi-cylindrically-focused. A calibration (or reference) signal is required and is used to deduce the measurement system efficiency function. This can be "invented" by the software using center frequency and bandwidth information specified by the user, or, alternatively, a measured calibration signal can be used. Defect types include flat-bottomed-hole reference reflectors, and spherical pores and inclusions. Simulation outputs include estimated defect signal amplitudes, root-mean-square values of grain noise amplitudes, and SNR as functions of the depth of the defect within the metal component. At any particular depth, the user can view

  8. Hardware control system using modular software under RSX-11D

    International Nuclear Information System (INIS)

    Kittell, R.S.; Helland, J.A.

    1978-01-01

    A modular software system used to control extensive hardware is described. The development, operation, and experience with this software are discussed. Included are the methods employed to implement this system while taking advantage of the Real-Time features of RSX-11D. Comparisons are made between this system and an earlier nonmodular system. The controlled hardware includes magnet power supplies, stepping motors, DVM's, and multiplexors, and is interfaced through CAMAC. 4 figures

  9. MATLAB simulation software used for the PhD thesis "Acquisition of Multi-Band Signals via Compressed Sensing

    DEFF Research Database (Denmark)

    2014-01-01

    MATLAB simulation software used for the PhD thesis "Acquisition of Multi-Band Signals via Compressed Sensing......MATLAB simulation software used for the PhD thesis "Acquisition of Multi-Band Signals via Compressed Sensing...

  10. Module-based Simulation System for efficient development of nuclear simulation programs

    International Nuclear Information System (INIS)

    Yoshikawa, Hidekazu; Wakabayashi, Jiro

    1990-01-01

    Module-based Simulation System (MSS) has been developed to realize a new software environment enabling versatile dynamic simulation of a complex nuclear power plant system flexibly. Described in the paper are (i) fundamental methods utilized in MMS and its software systemization, (ii) development of human interface system to help users in generating integrated simulation programs automatically, and (iii) development of an intelligent user support system for helping users in the two phases of automatical semantic diagnosis and consultation to automatic input data setup for the MSS-generated programs. (author)

  11. Sandia National Laboratories Advanced Simulation and Computing (ASC) software quality plan. Part 1: ASC software quality engineering practices, Version 2.0.

    Energy Technology Data Exchange (ETDEWEB)

    Sturtevant, Judith E.; Heaphy, Robert; Hodges, Ann Louise; Boucheron, Edward A.; Drake, Richard Roy; Minana, Molly A.; Hackney, Patricia; Forsythe, Christi A.; Schofield, Joseph Richard, Jr. (,; .); Pavlakos, Constantine James; Williamson, Charles Michael; Edwards, Harold Carter

    2006-09-01

    The purpose of the Sandia National Laboratories Advanced Simulation and Computing (ASC) Software Quality Plan is to clearly identify the practices that are the basis for continually improving the quality of ASC software products. The plan defines the ASC program software quality practices and provides mappings of these practices to Sandia Corporate Requirements CPR 1.3.2 and 1.3.6 and to a Department of Energy document, ASCI Software Quality Engineering: Goals, Principles, and Guidelines. This document also identifies ASC management and software project teams responsibilities in implementing the software quality practices and in assessing progress towards achieving their software quality goals.

  12. Reliability estimation of safety-critical software-based systems using Bayesian networks

    International Nuclear Information System (INIS)

    Helminen, A.

    2001-06-01

    Due to the nature of software faults and the way they cause system failures new methods are needed for the safety and reliability evaluation of software-based safety-critical automation systems in nuclear power plants. In the research project 'Programmable automation system safety integrity assessment (PASSI)', belonging to the Finnish Nuclear Safety Research Programme (FINNUS, 1999-2002), various safety assessment methods and tools for software based systems are developed and evaluated. The project is financed together by the Radiation and Nuclear Safety Authority (STUK), the Ministry of Trade and Industry (KTM) and the Technical Research Centre of Finland (VTT). In this report the applicability of Bayesian networks to the reliability estimation of software-based systems is studied. The applicability is evaluated by building Bayesian network models for the systems of interest and performing simulations for these models. In the simulations hypothetical evidence is used for defining the parameter relations and for determining the ability to compensate disparate evidence in the models. Based on the experiences from modelling and simulations we are able to conclude that Bayesian networks provide a good method for the reliability estimation of software-based systems. (orig.)

  13. Software System for Vocal Rendering of Printed Documents

    Directory of Open Access Journals (Sweden)

    Marian DARDALA

    2008-01-01

    Full Text Available The objective of this paper is to present a software system architecture developed to render the printed documents in a vocal form. On the other hand, in the paper are described the software solutions that exist as software components and are necessary for documents processing as well as for multimedia device controlling used by the system. The usefulness of this system is for people with visual disabilities that can access the contents of documents without that they be printed in Braille system or to exist in an audio form.

  14. A Configurable, Object-Oriented, Transportation System Software Framework

    Energy Technology Data Exchange (ETDEWEB)

    KELLY,SUZANNE M.; MYRE,JOHN W.; PRICE,MARK H.; RUSSELL,ERIC D.; SCOTT,DAN W.

    2000-08-01

    The Transportation Surety Center, 6300, has been conducting continuing research into and development of information systems for the Configurable Transportation Security and Information Management System (CTSS) project, an Object-Oriented Framework approach that uses Component-Based Software Development to facilitate rapid deployment of new systems while improving software cost containment, development reliability, compatibility, and extensibility. The direction has been to develop a Fleet Management System (FMS) framework using object-oriented technology. The goal for the current development is to provide a software and hardware environment that will demonstrate and support object-oriented development commonly in the FMS Central Command Center and Vehicle domains.

  15. The achievement and assessment of safety in systems containing software

    International Nuclear Information System (INIS)

    Ball, A.; Dale, C.J.; Butterfield, M.H.

    1986-01-01

    In order to establish confidence in the safe operation of a reactor protection system, there is a need to establish, as far as it is possible, that: (i) the algorithms used are correct; (ii) the system is a correct implementation of the algorithms; and (iii) the hardware is sufficiently reliable. This paper concentrates principally on the second of these, as it applies to the software aspect of the more accurate and complex trip functions to be performed by modern reactor protection systems. In order to engineer safety into software, there is a need to use a development strategy which will stand a high chance of achieving a correct implementation of the trip algorithms. This paper describes three broad methodologies by which it is possible to enhance the integrity of software: fault avoidance, fault tolerance and fault removal. Fault avoidance is concerned with making the software as fault free as possible by appropriate choice of specification, design and implementation methods. A fault tolerant strategy may be advisable in many safety critical applications, in order to guard against residual faults present in the software of the installed system. Fault detection and removal techniques are used to remove as many faults as possible of those introduced during software development. The paper also discusses safety and reliability assessment as it applies to software, outlining the various approaches available. Finally, there is an outline of a research project underway in the UKAEA which is intended to assess methods for developing and testing safety and protection systems involving software. (author)

  16. A three-dimensional breast software phantom for mammography simulation

    International Nuclear Information System (INIS)

    Bliznakova, K; Bliznakov, Z; Bravou, V; Kolitsi, Z; Pallikarakis, N

    2003-01-01

    This paper presents a methodology for three-dimensional (3D) computer modelling of the breast, using a combination of 3D geometrical primitives and voxel matrices that can be further subjected to simulated x-ray imaging, to produce synthetic mammograms. The breast phantom is a composite model of the breast and includes the breast surface, the duct system and terminal ductal lobular units, Cooper's ligaments, the pectoral muscle, the 3D mammographic background and breast abnormalities. A second analytical x-ray matter interaction modelling module is used to generate synthetic images from monoenergetic fan beams. Mammographic images of various synthesized breast models differing in size, shape and composition were produced. A preliminary qualitative assessment performed by three radiologists and a quantitative evaluation study using fractal and grey-level histogram analysis were conducted. A comparative study of extracted features with published data has also been performed. The evaluation results indicated good correlation of characteristics between synthetic and actual radiographs. Applications foreseen are not only in the area of breast imaging experimentation but also in education and training

  17. Availability simulation software adaptation to the IFMIF accelerator facility RAMI analyses

    International Nuclear Information System (INIS)

    Bargalló, Enric; Sureda, Pere Joan; Arroyo, Jose Manuel; Abal, Javier; De Blas, Alfredo; Dies, Javier; Tapia, Carlos; Mollá, Joaquín; Ibarra, Ángel

    2014-01-01

    Highlights: • The reason why IFMIF RAMI analyses needs a simulation is explained. • Changes, modifications and software validations done to AvailSim are described. • First IFMIF RAMI results obtained with AvailSim 2.0 are shown. • Implications of AvailSim 2.0 in IFMIF RAMI analyses are evaluated. - Abstract: Several problems were found when using generic reliability tools to perform RAMI (Reliability Availability Maintainability Inspectability) studies for the IFMIF (International Fusion Materials Irradiation Facility) accelerator. A dedicated simulation tool was necessary to model properly the complexity of the accelerator facility. AvailSim, the availability simulation software used for the International Linear Collider (ILC) became an excellent option to fulfill RAMI analyses needs. Nevertheless, this software needed to be adapted and modified to simulate the IFMIF accelerator facility in a useful way for the RAMI analyses in the current design phase. Furthermore, some improvements and new features have been added to the software. This software has become a great tool to simulate the peculiarities of the IFMIF accelerator facility allowing obtaining a realistic availability simulation. Degraded operation simulation and maintenance strategies are the main relevant features. In this paper, the necessity of this software, main modifications to improve it and its adaptation to IFMIF RAMI analysis are described. Moreover, first results obtained with AvailSim 2.0 and a comparison with previous results is shown

  18. Availability simulation software adaptation to the IFMIF accelerator facility RAMI analyses

    Energy Technology Data Exchange (ETDEWEB)

    Bargalló, Enric, E-mail: enric.bargallo-font@upc.edu [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Sureda, Pere Joan [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Arroyo, Jose Manuel [Laboratorio Nacional de Fusión por Confinamiento Magnético – CIEMAT, Madrid (Spain); Abal, Javier; De Blas, Alfredo; Dies, Javier; Tapia, Carlos [Fusion Energy Engineering Laboratory (FEEL), Technical University of Catalonia (UPC) Barcelona-Tech, Barcelona (Spain); Mollá, Joaquín; Ibarra, Ángel [Laboratorio Nacional de Fusión por Confinamiento Magnético – CIEMAT, Madrid (Spain)

    2014-10-15

    Highlights: • The reason why IFMIF RAMI analyses needs a simulation is explained. • Changes, modifications and software validations done to AvailSim are described. • First IFMIF RAMI results obtained with AvailSim 2.0 are shown. • Implications of AvailSim 2.0 in IFMIF RAMI analyses are evaluated. - Abstract: Several problems were found when using generic reliability tools to perform RAMI (Reliability Availability Maintainability Inspectability) studies for the IFMIF (International Fusion Materials Irradiation Facility) accelerator. A dedicated simulation tool was necessary to model properly the complexity of the accelerator facility. AvailSim, the availability simulation software used for the International Linear Collider (ILC) became an excellent option to fulfill RAMI analyses needs. Nevertheless, this software needed to be adapted and modified to simulate the IFMIF accelerator facility in a useful way for the RAMI analyses in the current design phase. Furthermore, some improvements and new features have been added to the software. This software has become a great tool to simulate the peculiarities of the IFMIF accelerator facility allowing obtaining a realistic availability simulation. Degraded operation simulation and maintenance strategies are the main relevant features. In this paper, the necessity of this software, main modifications to improve it and its adaptation to IFMIF RAMI analysis are described. Moreover, first results obtained with AvailSim 2.0 and a comparison with previous results is shown.

  19. Availability of software services for a hospital information system.

    Science.gov (United States)

    Sakamoto, N

    1998-03-01

    Hospital information systems (HISs) are becoming more important and covering more parts in daily hospital operations as order-entry systems become popular and electronic charts are introduced. Thus, HISs today need to be able to provide necessary services for hospital operations for a 24-h day, 365 days a year. The provision of services discussed here does not simply mean the availability of computers, in which all that matters is that the computer is functioning. It means the provision of necessary information for hospital operations by the computer software, and we will call it the availability of software services. HISs these days are mostly client-server systems. To increase availability of software services in these systems, it is not enough to just use system structures that are highly reliable in existing host-centred systems. Four main components which support availability of software services are network systems, client computers, server computers, and application software. In this paper, we suggest how to structure these four components to provide the minimum requested software services even if a part of the system stops to function. The network system should be double-protected in stratus using Asynchronous Transfer Mode (ATM) as its base network. Client computers should be fat clients with as much application logic as possible, and reference information which do not require frequent updates (master files, for example) should be replicated in clients. It would be best if all server computers could be double-protected. However, if that is physically impossible, one database file should be made accessible by several server computers. Still, at least the basic patients' information and the latest clinical records should be double-protected physically. Application software should be tested carefully before introduction. Different versions of the application software should always be kept and managed in case the new version has problems. If a hospital

  20. The software product assurance metrics study: JPL's software systems quality and productivity

    Science.gov (United States)

    Bush, Marilyn W.

    1989-01-01

    The findings are reported of the Jet Propulsion Laboratory (JPL)/Software Product Assurance (SPA) Metrics Study, conducted as part of a larger JPL effort to improve software quality and productivity. Until recently, no comprehensive data had been assembled on how JPL manages and develops software-intensive systems. The first objective was to collect data on software development from as many projects and for as many years as possible. Results from five projects are discussed. These results reflect 15 years of JPL software development, representing over 100 data points (systems and subsystems), over a third of a billion dollars, over four million lines of code and 28,000 person months. Analysis of this data provides a benchmark for gauging the effectiveness of past, present and future software development work. In addition, the study is meant to encourage projects to record existing metrics data and to gather future data. The SPA long term goal is to integrate the collection of historical data and ongoing project data with future project estimations.

  1. Systems and software variability management concepts, tools and experiences

    CERN Document Server

    Capilla, Rafael; Kang, Kyo-Chul

    2013-01-01

    The success of product line engineering techniques in the last 15 years has popularized the use of software variability as a key modeling approach for describing the commonality and variability of systems at all stages of the software lifecycle. Software product lines enable a family of products to share a common core platform, while allowing for product specific functionality being built on top of the platform. Many companies have exploited the concept of software product lines to increase the resources that focus on highly differentiating functionality and thus improve their competitiveness

  2. The Software Bus, an Object-Oriented Data Exchange System

    International Nuclear Information System (INIS)

    Akerbaek, T.; Louka, M.

    1996-01-01

    This document describes the Software Bus System, developed for object-oriented task to task communication in a TCP/IP based network. The Software Bus is a set of library functions, developed to be used for the Picasso-3 UIMS, and as a general purpose tool for dynamically interfacing programs at run-time. The Software Bus offers a high level object-oriented data exchange mechanism that relieves the application programmer of the low level TCP/IP-programming and communication protocol handling. The Software Bus is currently available under several UNIX platforms and a version for Windows NT is planned for late 1996. (author)

  3. Software Engineering Issues for Cyber-Physical Systems

    DEFF Research Database (Denmark)

    Al-Jaroodi, Jameela; Mohamed, Nader; Jawhar, Imad

    2016-01-01

    step; however, designing and implementing the right software to integrate and use them effectively is essential. The software facilitates better interfaces, more control and adds smart services, high flexibility and many other added values and features to the CPS. However, software development for CPS......Cyber-Physical Systems (CPS) provide many smart features for enhancing physical processes. These systems are designed with a set of distributed hardware, software, and network components that are embedded in physical systems and environments or attached to humans. Together they function seamlessly...... to offer specific functionalities or features that help enhance human lives, operations or environments. While different CPS components play important roles in a successful CPS development, the software plays the most important role among them. Acquiring and using high quality CPS components is the first...

  4. Testing methodology of embedded software in digital plant protection system

    International Nuclear Information System (INIS)

    Seong, Ah Young; Choi, Bong Joo; Lee, Na Young; Hwang, Il Soon

    2001-01-01

    It is necessary to assure the reliability of software in order to digitalize RPS(Reactor Protection System). Since RPS causes fatal damage on accidental cases, it is classified as Safety 1E class. Therefore we propose the effective testing methodology to assure the reliability of embedded software in the DPPS(Digital Plant Protection System). To test the embedded software effectively in DPPS, our methodology consists of two steps. The first is the re-engineering step that extracts classes from structural source program, and the second is the level of testing step which is composed of unit testing, Integration Testing and System Testing. On each testing step we test the embedded software with selected test cases after the test item identification step. If we use this testing methodology, we can test the embedded software effectively by reducing the cost and the time

  5. Accelerating Project and Process Improvement using Advanced Software Simulation Technology: From the Office to the Enterprise

    Science.gov (United States)

    2010-04-29

    Technology: From the Office Larry Smith Software Technology Support Center to the Enterprise 517 SMXS/MXDEA 6022 Fir Avenue Hill AFB, UT 84056 801...2010 to 00-00-2010 4. TITLE AND SUBTITLE Accelerating Project and Process Improvement using Advanced Software Simulation Technology: From the Office to

  6. The Virtual Genetics Lab II: Improvements to a Freely Available Software Simulation of Genetics

    Science.gov (United States)

    White, Brian T.

    2012-01-01

    The Virtual Genetics Lab II (VGLII) is an improved version of the highly successful genetics simulation software, the Virtual Genetics Lab (VGL). The software allows students to use the techniques of genetic analysis to design crosses and interpret data to solve realistic genetics problems involving a hypothetical diploid insect. This is a brief…

  7. An Educational Software for Simulating the Sample Size of Molecular Marker Experiments

    Science.gov (United States)

    Helms, T. C.; Doetkott, C.

    2007-01-01

    We developed educational software to show graduate students how to plan molecular marker experiments. These computer simulations give the students feedback on the precision of their experiments. The objective of the software was to show students using a hands-on approach how: (1) environmental variation influences the range of the estimates of the…

  8. DAE Tools: equation-based object-oriented modelling, simulation and optimisation software

    Directory of Open Access Journals (Sweden)

    Dragan D. Nikolić

    2016-04-01

    Full Text Available In this work, DAE Tools modelling, simulation and optimisation software, its programming paradigms and main features are presented. The current approaches to mathematical modelling such as the use of modelling languages and general-purpose programming languages are analysed. The common set of capabilities required by the typical simulation software are discussed, and the shortcomings of the current approaches recognised. A new hybrid approach is introduced, and the modelling languages and the hybrid approach are compared in terms of the grammar, compiler, parser and interpreter requirements, maintainability and portability. The most important characteristics of the new approach are discussed, such as: (1 support for the runtime model generation; (2 support for the runtime simulation set-up; (3 support for complex runtime operating procedures; (4 interoperability with the third party software packages (i.e. NumPy/SciPy; (5 suitability for embedding and use as a web application or software as a service; and (6 code-generation, model exchange and co-simulation capabilities. The benefits of an equation-based approach to modelling, implemented in a fourth generation object-oriented general purpose programming language such as Python are discussed. The architecture and the software implementation details as well as the type of problems that can be solved using DAE Tools software are described. Finally, some applications of the software at different levels of abstraction are presented, and its embedding capabilities and suitability for use as a software as a service is demonstrated.

  9. 78 FR 47011 - Software Unit Testing for Digital Computer Software Used in Safety Systems of Nuclear Power Plants

    Science.gov (United States)

    2013-08-02

    ... NUCLEAR REGULATORY COMMISSION [NRC-2012-0195] Software Unit Testing for Digital Computer Software... revised regulatory guide (RG), revision 1 of RG 1.171, ``Software Unit Testing for Digital Computer Software Used in Safety Systems of Nuclear Power Plants.'' This RG endorses American National Standards...

  10. 77 FR 50722 - Software Unit Testing for Digital Computer Software Used in Safety Systems of Nuclear Power Plants

    Science.gov (United States)

    2012-08-22

    ... NUCLEAR REGULATORY COMMISSION [NRC-2012-0195] Software Unit Testing for Digital Computer Software...) is issuing for public comment draft regulatory guide (DG), DG-1208, ``Software Unit Testing for Digital Computer Software used in Safety Systems of Nuclear Power Plants.'' The DG-1208 is proposed...

  11. Software quality and process improvement in scientific simulation codes

    Energy Technology Data Exchange (ETDEWEB)

    Ambrosiano, J.; Webster, R. [Los Alamos National Lab., NM (United States)

    1997-11-01

    This report contains viewgraphs on the quest to develope better simulation code quality through process modeling and improvement. This study is based on the experience of the authors and interviews with ten subjects chosen from simulation code development teams at LANL. This study is descriptive rather than scientific.

  12. Software Infrastructure to Enable Modeling & Simulation as a Service (M&SaaS), Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase 2 project will produce a software service infrastructure that enables most modeling and simulation (M&S) activities from code development and...

  13. SOFTM: a software maintenance expert system in Prolog

    DEFF Research Database (Denmark)

    Pau, L.; Negret, J. M.

    1988-01-01

    A description is given of a knowledge-based system called SOFTM, serving the following purposes: (1) assisting a software programmer or analyst in his application code maintenance tasks, (2) generating and updating automatically software correction documentation, (3) helping the end user register......, and on interfacing capabilities of Prolog II to a variety of other languages...

  14. Integrated analysis software for bulk power system stability

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, T; Nagao, T; Takahashi, K [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

    1994-12-31

    This paper presents Central Research Inst.of Electric Power Industry - CRIEPI`s - own developed three softwares for bulk power network analysis and the user support system which arranges tremendous data necessary for these softwares with easy and high reliability. (author) 3 refs., 7 figs., 2 tabs.

  15. Software for ASS-500 based early warning system

    International Nuclear Information System (INIS)

    Lipinski, P.; Isajenko, K.

    1998-01-01

    The article describes the software for the management of early warning system based on ASS-500 station. The software can communicate with the central computer using TCP/IP protocol. This allows remote control of the station through modem or local area network connection. The article describes Windows based user interface of the program

  16. Conceptual design for controller software of mechatronic systems

    NARCIS (Netherlands)

    Broenink, Johannes F.; Hilderink, G.H.; Bakkers, André; Bradshaw, Alan; Counsell, John

    1998-01-01

    The method and software tool presented here, aims at supporting the development of control software for mechatronic systems. Heterogeneous distributed embedded processors are considered as target hardware. Principles of the method are that the implementation process is a stepwise refinement from

  17. Automated transportation management system (ATMS) software project management plan (SPMP)

    Energy Technology Data Exchange (ETDEWEB)

    Weidert, R.S., Westinghouse Hanford

    1996-05-20

    The Automated Transportation Management System (ATMS) Software Project Management plan (SPMP) is the lead planning document governing the life cycle of the ATMS and its integration into the Transportation Information Network (TIN). This SPMP defines the project tasks, deliverables, and high level schedules involved in developing the client/server ATMS software.

  18. Applications of Cerius2, software of molecular simulation; Aplicaciones de Cerius2, software de simulacion molecular

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez G, M E; Perez A, M; Gutierrez W, C E [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)

    2007-07-01

    Most of the investigations have a theoretical sustenance based on molecular simulation. The area of application of molecular simulation is very wide, in the Materials Technology Department assigned to the Applied Sciences Management have been treated problems about metallic nano structures, glasses, interfaces, and molecules, to sustain and to explain some of the experimental results. Energy calculations are carried out to determine minimum energy structures, for later on to carry out calculations of some of their properties; as well as the images simulation of Electron microscopy and X-ray diffraction. (Author)

  19. Simulation of the Energy Saver refrigeration system

    International Nuclear Information System (INIS)

    Barton, H.R. Jr.; Nicholls, J.E.; Mulholland, G.T.

    1981-10-01

    The helium refrigeration for the Energy Saver is supplied by a Central Helium Liquefier and 24 Satellite Refrigerators installed over a 1-1/4 square mile area. An interactive, software simulator has been developed to calculate the refrigeration available from the cryogenic system over a wide range of operating conditions. The refrigeration system simulator incorporates models of the components which have been developed to quantitatively describe changes in system performance. The simulator output is presented in a real-time display which has been used to search for the optimal operating conditions of the Satellite-Central system, to examine the effect of an extended range of operating parameters and to identify equipment modifications which would improve the system performance

  20. Software architecture considerations for ion source control systems

    International Nuclear Information System (INIS)

    Sinclair, J.W.

    1997-09-01

    General characteristics of distributed control system software tools are examined from the perspective of ion source control system requirements. Emphasis is placed on strategies for building extensible, distributed systems in which the ion source element is one component of a larger system. Vsystem, a commercial software tool kit from Vista Control Systems was utilized extensively in the control system upgrade of the Holifield Radioactive Ion Beam Facility. Part of the control system is described and the characteristics of Vsystem are examined and compared with those of EPICS, the Experimental Physics and Industrial Control System

  1. Analysis for Parallel Execution without Performing Hardware/Software Co-simulation

    OpenAIRE

    Muhammad Rashid

    2014-01-01

    Hardware/software co-simulation improves the performance of embedded applications by executing the applications on a virtual platform before the actual hardware is available in silicon. However, the virtual platform of the target architecture is often not available during early stages of the embedded design flow. Consequently, analysis for parallel execution without performing hardware/software co-simulation is required. This article presents an analysis methodology for parallel execution of ...

  2. Epistemic Opacity, Confirmation Holism and Technical Debt: Computer Simulation in the Light of Empirical Software Engineering

    OpenAIRE

    Newman , Julian

    2015-01-01

    Epistemic opacity vis a vis human agents has been presented as an essential, ineliminable characteristic of computer simulation models resulting from the characteristics of the human cognitive agent. This paper argues, on the contrary, that such epistemic opacity as does occur in computer simulations is not a consequence of human limitations but of a failure on the part of model developers to adopt good software engineering practice for managing human error and ensuring the software artefact ...

  3. Prototype Software for Automated Structural Analysis of Systems

    DEFF Research Database (Denmark)

    Jørgensen, A.; Izadi-Zamanabadi, Roozbeh; Kristensen, M.

    2004-01-01

    In this paper we present a prototype software tool that is developed to analyse the structural model of automated systems in order to identify redundant information that is hence utilized for Fault detection and Isolation (FDI) purposes. The dedicated algorithms in this software tool use a tri......-partite graph that represents the structural model of the system. A component-based approach has been used to address issues such as system complexity and recon¯gurability possibilities....

  4. Prototype Software for Automated Structural Analysis of Systems

    DEFF Research Database (Denmark)

    Jørgensen, A.; Izadi-Zamanabadi, Roozbeh; Kristensen, M.

    2004-01-01

    In this paper we present a prototype software tool that is developed to analyse the structural model of automated systems in order to identify redundant information that is hence utilized for Fault detection and Isolation (FDI) purposes. The dedicated algorithms in this software tool use a tri......-partite graph that represents the structural model of the system. A component-based approach has been used to address issues such as system complexity and reconfigurability possibilities....

  5. Implementation in free software of the PWR type university nucleo electric simulator (SU-PWR)

    International Nuclear Information System (INIS)

    Valle H, J.; Hidago H, F.; Morales S, J.B.

    2007-01-01

    Presently work is shown like was carried out the implementation of the University Simulator of Nucleo-electric type PWR (SU-PWR). The implementation of the simulator was carried out in a free software simulation platform, as it is Scilab, what offers big advantages that go from the free use and without cost of the product, until the codes modification so much of the system like of the program with the purpose of to improve it or to adapt it to future routines and/or more advanced graphic interfaces. The SU-PWR shows the general behavior of a PWR nuclear plant (Pressurized Water Reactor) describing the dynamics of the plant from the generation process of thermal energy in the nuclear fuel, going by the process of energy transport toward the coolant of the primary circuit the one which in turn transfers this energy to the vapor generators of the secondary circuit where the vapor is expanded by means of turbines that in turn move the electric generator producing in this way the electricity. The pressurizer that is indispensable for the process is also modeled. Each one of these stages were implemented in scicos that is the Scilab tool specialized in the simulation. The simulation was carried out by means of modules that contain the differential equation that mathematically models each stage or equipment of the PWR plant. The result is a series of modules that based on certain entrances and characteristic of the system they generate exits that in turn are the entrance to other module. Because the SU-PWR is an experimental project in early phase, it is even work and modifications to carry out, for what the models that are presented in this work can vary a little the being integrated to the whole system to simulate, but however they already show clearly the operation and the conformation of the plant. (Author)

  6. Capturing security requirements for software systems.

    Science.gov (United States)

    El-Hadary, Hassan; El-Kassas, Sherif

    2014-07-01

    Security is often an afterthought during software development. Realizing security early, especially in the requirement phase, is important so that security problems can be tackled early enough before going further in the process and avoid rework. A more effective approach for security requirement engineering is needed to provide a more systematic way for eliciting adequate security requirements. This paper proposes a methodology for security requirement elicitation based on problem frames. The methodology aims at early integration of security with software development. The main goal of the methodology is to assist developers elicit adequate security requirements in a more systematic way during the requirement engineering process. A security catalog, based on the problem frames, is constructed in order to help identifying security requirements with the aid of previous security knowledge. Abuse frames are used to model threats while security problem frames are used to model security requirements. We have made use of evaluation criteria to evaluate the resulting security requirements concentrating on conflicts identification among requirements. We have shown that more complete security requirements can be elicited by such methodology in addition to the assistance offered to developers to elicit security requirements in a more systematic way.

  7. Capturing security requirements for software systems

    Directory of Open Access Journals (Sweden)

    Hassan El-Hadary

    2014-07-01

    Full Text Available Security is often an afterthought during software development. Realizing security early, especially in the requirement phase, is important so that security problems can be tackled early enough before going further in the process and avoid rework. A more effective approach for security requirement engineering is needed to provide a more systematic way for eliciting adequate security requirements. This paper proposes a methodology for security requirement elicitation based on problem frames. The methodology aims at early integration of security with software development. The main goal of the methodology is to assist developers elicit adequate security requirements in a more systematic way during the requirement engineering process. A security catalog, based on the problem frames, is constructed in order to help identifying security requirements with the aid of previous security knowledge. Abuse frames are used to model threats while security problem frames are used to model security requirements. We have made use of evaluation criteria to evaluate the resulting security requirements concentrating on conflicts identification among requirements. We have shown that more complete security requirements can be elicited by such methodology in addition to the assistance offered to developers to elicit security requirements in a more systematic way.

  8. Spaceport Command and Control System Software Development

    Science.gov (United States)

    Mahlin, Jonathan Nicholas

    2017-01-01

    There is an immense challenge in organizing personnel across a large agency such as NASA, or even over a subset of that, like a center's Engineering directorate. Workforce inefficiencies and challenges are bound to grow over time without oversight and management. It is also not always possible to hire new employees to fill workforce gaps, therefore available resources must be utilized more efficiently. The goal of this internship was to develop software that improves organizational efficiency by aiding managers, making employee information viewable and editable in an intuitive manner. This semester I created an application for managers that aids in optimizing allocation of employee resources for a single division with the possibility of scaling upwards. My duties this semester consisted of developing frontend and backend software to complete this task. The application provides user-friendly information displays and documentation of the workforce to allow NASA to track diligently track the status and skills of its workforce. This tool should be able to prove that current employees are being effectively utilized and if new hires are necessary to fulfill skill gaps.

  9. Capturing security requirements for software systems

    Science.gov (United States)

    El-Hadary, Hassan; El-Kassas, Sherif

    2014-01-01

    Security is often an afterthought during software development. Realizing security early, especially in the requirement phase, is important so that security problems can be tackled early enough before going further in the process and avoid rework. A more effective approach for security requirement engineering is needed to provide a more systematic way for eliciting adequate security requirements. This paper proposes a methodology for security requirement elicitation based on problem frames. The methodology aims at early integration of security with software development. The main goal of the methodology is to assist developers elicit adequate security requirements in a more systematic way during the requirement engineering process. A security catalog, based on the problem frames, is constructed in order to help identifying security requirements with the aid of previous security knowledge. Abuse frames are used to model threats while security problem frames are used to model security requirements. We have made use of evaluation criteria to evaluate the resulting security requirements concentrating on conflicts identification among requirements. We have shown that more complete security requirements can be elicited by such methodology in addition to the assistance offered to developers to elicit security requirements in a more systematic way. PMID:25685514

  10. Traceability of Software Safety Requirements in Legacy Safety Critical Systems

    Science.gov (United States)

    Hill, Janice L.

    2007-01-01

    How can traceability of software safety requirements be created for legacy safety critical systems? Requirements in safety standards are imposed most times during contract negotiations. On the other hand, there are instances where safety standards are levied on legacy safety critical systems, some of which may be considered for reuse for new applications. Safety standards often specify that software development documentation include process-oriented and technical safety requirements, and also require that system and software safety analyses are performed supporting technical safety requirements implementation. So what can be done if the requisite documents for establishing and maintaining safety requirements traceability are not available?

  11. Using Software Architectures for Designing Distributed Embedded Systems

    DEFF Research Database (Denmark)

    Christensen, Henrik Bærbak

    In this paper, we outline an on-going project of designing distributed embedded systems for closed-loop process control. The project is a joint effort between software architecture researchers and developers from two companies that produce commercial embedded process control systems. The project...... has a strong emphasis on software architectural issues and terminology in order to envision, design and analyze design alternatives. We present two results. First, we outline how focusing on software architecture, architectural issues and qualities are beneficial in designing distributed, embedded......, systems. Second, we present two different architectures for closed-loop process control and discuss benefits and reliabilities....

  12. Applications of Cerius2, software of molecular simulation

    International Nuclear Information System (INIS)

    Fernandez G, M.E.; Perez A, M.; Gutierrez W, C.E.

    2007-01-01

    Most of the investigations have a theoretical sustenance based on molecular simulation. The area of application of molecular simulation is very wide, in the Materials Technology Department assigned to the Applied Sciences Management have been treated problems about metallic nano structures, glasses, interfaces, and molecules, to sustain and to explain some of the experimental results. Energy calculations are carried out to determine minimum energy structures, for later on to carry out calculations of some of their properties; as well as the images simulation of Electron microscopy and X-ray diffraction. (Author)

  13. Computer software design description for the integrated control and data acquisition system LDUA system

    International Nuclear Information System (INIS)

    Aftanas, B.L.

    1998-01-01

    This Computer Software Design Description (CSDD) document provides the overview of the software design for all the software that is part of the integrated control and data acquisition system of the Light Duty Utility Arm System (LDUA). It describes the major software components and how they interface. It also references the documents that contain the detailed design description of the components

  14. Diversity requirements for safety critical software-based automation systems

    International Nuclear Information System (INIS)

    Korhonen, J.; Pulkkinen, U.; Haapanen, P.

    1998-03-01

    System vendors nowadays propose software-based systems even for the most critical safety functions in nuclear power plants. Due to the nature and mechanisms of influence of software faults new methods are needed for the safety and reliability evaluation of these systems. In the research project 'Programmable automation systems in nuclear power plants (OHA)' various safety assessment methods and tools for software based systems are developed and evaluated. This report first discusses the (common cause) failure mechanisms in software-based systems, then defines fault-tolerant system architectures to avoid common cause failures, then studies the various alternatives to apply diversity and their influence on system reliability. Finally, a method for the assessment of diversity is described. Other recently published reports in OHA-report series handles the statistical reliability assessment of software based (STUK-YTO-TR 119), usage models in reliability assessment of software-based systems (STUK-YTO-TR 128) and handling of programmable automation in plant PSA-studies (STUK-YTO-TR 129)

  15. The art of software thermal management for embedded systems

    CERN Document Server

    Benson, Mark

    2014-01-01

    This book introduces Software Thermal Management (STM) as a means of reducing power consumption in a computing system, in order to manage heat, improve component reliability, and increase system safety.  Readers will benefit from this pragmatic guide to the field of STM for embedded systems and its catalog of software power management techniques.  Since thermal management is a key bottleneck in embedded systems design, this book focuses on power as the root cause of heat. Since software has an enormous impact on power consumption in an embedded system, this book guides readers to manage heat effectively by understanding, categorizing, and developing new ways to reduce dynamic power. Whereas most books on thermal management describe mechanisms to remove heat, this book focuses on ways to avoid generating heat in the first place.   • Explains fundamentals of software thermal management, application techniques and advanced optimization strategies; • Describes a novel method for managing dynamic power, e...

  16. Application of automated reasoning software: procedure generation system verifier

    International Nuclear Information System (INIS)

    Smith, D.E.; Seeman, S.E.

    1984-09-01

    An on-line, automated reasoning software system for verifying the actions of other software or human control systems has been developed. It was demonstrated by verifying the actions of an automated procedure generation system. The verifier uses an interactive theorem prover as its inference engine with the rules included as logic axioms. Operation of the verifier is generally transparent except when the verifier disagrees with the actions of the monitored software. Testing with an automated procedure generation system demonstrates the successful application of automated reasoning software for verification of logical actions in a diverse, redundant manner. A higher degree of confidence may be placed in the verified actions gathered by the combined system

  17. A study of software safety analysis system for safety-critical software

    International Nuclear Information System (INIS)

    Chang, H. S.; Shin, H. K.; Chang, Y. W.; Jung, J. C.; Kim, J. H.; Han, H. H.; Son, H. S.

    2004-01-01

    The core factors and requirements for the safety-critical software traced and the methodology adopted in each stage of software life cycle are presented. In concept phase, Failure Modes and Effects Analysis (FMEA) for the system has been performed. The feasibility evaluation of selected safety parameter was performed and Preliminary Hazards Analysis list was prepared using HAZOP(Hazard and Operability) technique. And the check list for management control has been produced via walk-through technique. Based on the evaluation of the check list, activities to be performed in requirement phase have been determined. In the design phase, hazard analysis has been performed to check the safety capability of the system with regard to safety software algorithm using Fault Tree Analysis (FTA). In the test phase, the test items based on FMEA have been checked for fitness guided by an accident scenario. The pressurizer low pressure trip algorithm has been selected to apply FTA method to software safety analysis as a sample. By applying CASE tool, the requirements traceability of safety critical system has been enhanced during all of software life cycle phases

  18. AVNG System Software-Attribute Verification System with Information Barriers for Mass Isotopic Measurements

    International Nuclear Information System (INIS)

    Elmont, T.H.; Langner, Diana C.; MacArthur, D.W.; Mayo, D.R.; Smith, M.K.; Modenov, A.

    2005-01-01

    This report describes the software development for the plutonium attribute verification system - AVNG. A brief synopsis of the technical solution for the measurement system is presented. The main tasks for the software development that is underway are formulated. The development tasks are shown in software structural flowcharts, measurement system state diagram and a description of the software. The current status of the AVNG software development is elucidated.

  19. Customizable software architectures in the accelerator control system environment

    CERN Document Server

    Mejuev, I; Kadokura, E

    2001-01-01

    Tailoring is further evolution of an application after deployment in order to adapt it to requirements that were not accounted for in the original design. End-user customization has been extensively researched in applied computer science from HCI and software engineering perspectives. Customization allows coping with flexibility requirements, decreasing maintenance and development costs of software products. In general, dynamic or diverse software requirements constitute the need for implementing end-user customization in computer systems. In accelerator physics research the factor of dynamic requirements is especially important, due to frequent software and hardware modifications resulting in correspondingly high upgrade and maintenance costs. We introduce the results of feasibility study on implementing end-user tailorability in the software for accelerator control system, considering the design and implementation of a distributed monitoring application for the 12 GeV KEK Proton Synchrotron as an example. T...

  20. Empirical Validation of Building Simulation Software : Modeling of Double Facades

    DEFF Research Database (Denmark)

    Kalyanova, Olena; Heiselberg, Per

    The work described in this report is the result of a collaborative effort of members of the International Energy Agency (IEA), Task 34/43: Testing and validation of building energy simulation tools experts group.......The work described in this report is the result of a collaborative effort of members of the International Energy Agency (IEA), Task 34/43: Testing and validation of building energy simulation tools experts group....