The SSCL framework software plans

International Nuclear Information System (INIS)

Frederiksen, S.

1993-12-01

In about ten years the Superconducting Super Collider Laboratory (SSCL) will be Producing 40 TeV proton-proton interactions. The size and scale of the effort demands new approaches to design and develop software used by the experimental collaborations. The Physics Research Division Computing Department (PRCD) of the SSCL is developing (in collaboration with the Solenoidal Detector Collaboration (SDC) and Gamma, Electron and Muon (GEM) collaborations a support system which will be used to build and run the collaboration software. It will be used for simulating the events needed for detector development and for the analysis of these complicated events. The plans status of this program will be discussed

SMART-P MMIS Software Development by Considering the Software License for Nuclear Power Plants and the Development Cost

International Nuclear Information System (INIS)

Suh, Yong Suk; Park, Jae Hong; Park, Heui Youn; Son, Ki Sung; Lee, Ki Hyun; Kim, Hyeon Soo

2005-01-01

The acceptance criteria of software for safety system functions in NPPs (Nuclear Power Plants) are as follows: 1) acceptable plans should be prepared to control the software development activities, 2) the plans should be followed in an acceptable software life cycle, and 3) the process should produce acceptable design outputs. The KINS (Korea Institute of Nuclear Safety) recommended that the software life cycle should be established based on the IEEE Std 1074 with a supplementary requirement of a software safety analysis. The KINS emphasized that the software should be developed to show its high qualities. This paper identifies the major requirements to achieve the software license from the KINS and presents the major facts reflected in the SMART-P (System-integrated Modular Advanced ReacTor-Pilot) MMIS (Man-Machine Interface Systems) which is being developed by KAERI and targeted to start operation in 2010. This paper also addresses major concerns on the development of a safety critical software and the facts reflected in the SMART-P MMIS

Tank monitor and control system (TMACS) software configuration management plan; TOPICAL

International Nuclear Information System (INIS)

GLASSCOCK, J.A.

1999-01-01

This Software Configuration Management Plan (SCMP) describes the methodology for control of computer software developed and supported by the Systems Development and Integration (SD and I) organization of Lockheed Martin Services, Inc. (LMSI) for the Tank Monitor and Control System (TMACS). This plan controls changes to the software and configuration files used by TMACS. The controlled software includes the Gensym software package, Gensym knowledge base files developed for TMACS, C-language programs used by TMACS, the operating system on the production machine, language compilers, and all Windows NT commands and functions which affect the operating environment. The configuration files controlled include the files downloaded to the Acromag and Westronic field instruments

Investigating the effects of different factors on development of open source enterprise resources planning software packages

Directory of Open Access Journals (Sweden)

Mehdi Ghorbaninia

2014-08-01

Full Text Available This paper investigates the effects of different factors on development of open source enterprise resources planning software packages. The study designs a questionnaire in Likert scale and distributes it among 210 experts in the field of open source software package development. Cronbach alpha has been calculated as 0.93, which is well above the minimum acceptable level. Using Pearson correlation as well as stepwise regression analysis, the study determines three most important factors including fundamental issues, during and after implementation of open source software development. The study also determines a positive and strong relationship between fundamental factors and after implementation factors (r=0.9006, Sig. = 0.000.

Software development processes and analysis software: a mismatch and a novel framework

International Nuclear Information System (INIS)

Kelly, D.; Harauz, J.

2011-01-01

This paper discusses the salient characteristics of analysis software and the impact of those characteristics on its development. From this discussion, it can be seen that mainstream software development processes, usually characterized as Plan Driven or Agile, are built upon assumptions that are mismatched to the development and maintenance of analysis software. We propose a novel software development framework that would match the process normally observed in the development of analysis software. In the discussion of this framework, we suggest areas of research and directions for future work. (author)

Sandia National Laboratories Advanced Simulation and Computing (ASC) software quality plan : ASC software quality engineering practices Version 3.0.

Energy Technology Data Exchange (ETDEWEB)

Turgeon, Jennifer L.; Minana, Molly A.; Hackney, Patricia; Pilch, Martin M.

2009-01-01

The purpose of the Sandia National Laboratories (SNL) Advanced Simulation and Computing (ASC) Software Quality Plan is to clearly identify the practices that are the basis for continually improving the quality of ASC software products. Quality is defined in the US Department of Energy/National Nuclear Security Agency (DOE/NNSA) Quality Criteria, Revision 10 (QC-1) as 'conformance to customer requirements and expectations'. This quality plan defines the SNL ASC Program software quality engineering (SQE) practices and provides a mapping of these practices to the SNL Corporate Process Requirement (CPR) 001.3.6; 'Corporate Software Engineering Excellence'. This plan also identifies ASC management's and the software project teams responsibilities in implementing the software quality practices and in assessing progress towards achieving their software quality goals. This SNL ASC Software Quality Plan establishes the signatories commitments to improving software products by applying cost-effective SQE practices. This plan enumerates the SQE practices that comprise the development of SNL ASC's software products and explains the project teams opportunities for tailoring and implementing the practices.

Automated transportation management system (ATMS) software project management plan (SPMP)

Energy Technology Data Exchange (ETDEWEB)

Weidert, R.S., Westinghouse Hanford

1996-05-20

The Automated Transportation Management System (ATMS) Software Project Management plan (SPMP) is the lead planning document governing the life cycle of the ATMS and its integration into the Transportation Information Network (TIN). This SPMP defines the project tasks, deliverables, and high level schedules involved in developing the client/server ATMS software.

Application of PIMS Software in Monthly Planning of Refinery Production

Institute of Scientific and Technical Information of China (English)

无

2005-01-01

This article describes the application of the PIMS software in formulating monthly refining production plan. Application of the PIMS software can help to solve a series of problems related with monthly plan of refining production such as optimized selection of crude and feedstocks, optimized selection of production scale and processing scheme, identification of bottlenecks and their mitigation,optimized selection of turnaround time and optimized selection of operating regime, which have increased the economic benefits of refining enterprises. With the further development and improvement of models the PIMS software will play an increasingly important role in formulating monthly plans of refining operations and production management at refineries. This article also explores the problems existing in refinery monthly planning, and has made recommendations on developing and improving models and reporting system, enhancement of basic data acquisition, model maintenance personnel and staff training.

Web Application Software for Ground Operations Planning Database (GOPDb) Management

Science.gov (United States)

Lanham, Clifton; Kallner, Shawn; Gernand, Jeffrey

2013-01-01

A Web application facilitates collaborative development of the ground operations planning document. This will reduce costs and development time for new programs by incorporating the data governance, access control, and revision tracking of the ground operations planning data. Ground Operations Planning requires the creation and maintenance of detailed timelines and documentation. The GOPDb Web application was created using state-of-the-art Web 2.0 technologies, and was deployed as SaaS (Software as a Service), with an emphasis on data governance and security needs. Application access is managed using two-factor authentication, with data write permissions tied to user roles and responsibilities. Multiple instances of the application can be deployed on a Web server to meet the robust needs for multiple, future programs with minimal additional cost. This innovation features high availability and scalability, with no additional software that needs to be bought or installed. For data governance and security (data quality, management, business process management, and risk management for data handling), the software uses NAMS. No local copy/cloning of data is permitted. Data change log/tracking is addressed, as well as collaboration, work flow, and process standardization. The software provides on-line documentation and detailed Web-based help. There are multiple ways that this software can be deployed on a Web server to meet ground operations planning needs for future programs. The software could be used to support commercial crew ground operations planning, as well as commercial payload/satellite ground operations planning. The application source code and database schema are owned by NASA.

Software development for teleroentgenogram analysis

Science.gov (United States)

Goshkoderov, A. A.; Khlebnikov, N. A.; Obabkov, I. N.; Serkov, K. V.; Gajniyarov, I. M.; Aliev, A. A.

2017-09-01

A framework for the analysis and calculation of teleroentgenograms was developed. Software development was carried out in the Department of Children's Dentistry and Orthodontics in Ural State Medical University. The software calculates the teleroentgenogram by the original method which was developed in this medical department. Program allows designing its own methods for calculating the teleroentgenograms by new methods. It is planned to use the technology of machine learning (Neural networks) in the software. This will help to make the process of calculating the teleroentgenograms easier because methodological points will be placed automatically.

Sandia National Laboratories Advanced Simulation and Computing (ASC) software quality plan. Part 1 : ASC software quality engineering practices version 1.0.

Energy Technology Data Exchange (ETDEWEB)

Minana, Molly A.; Sturtevant, Judith E.; Heaphy, Robert; Hodges, Ann Louise; Boucheron, Edward A.; Drake, Richard Roy; Forsythe, Christi A.; Schofield, Joseph Richard, Jr.; Pavlakos, Constantine James; Williamson, Charles Michael; Edwards, Harold Carter

2005-01-01

The purpose of the Sandia National Laboratories (SNL) Advanced Simulation and Computing (ASC) Software Quality Plan is to clearly identify the practices that are the basis for continually improving the quality of ASC software products. Quality is defined in DOE/AL Quality Criteria (QC-1) as conformance to customer requirements and expectations. This quality plan defines the ASC program software quality practices and provides mappings of these practices to the SNL Corporate Process Requirements (CPR 1.3.2 and CPR 1.3.6) and the Department of Energy (DOE) document, ASCI Software Quality Engineering: Goals, Principles, and Guidelines (GP&G). This quality plan identifies ASC management and software project teams' responsibilities for cost-effective software engineering quality practices. The SNL ASC Software Quality Plan establishes the signatories commitment to improving software products by applying cost-effective software engineering quality practices. This document explains the project teams opportunities for tailoring and implementing the practices; enumerates the practices that compose the development of SNL ASC's software products; and includes a sample assessment checklist that was developed based upon the practices in this document.

Evaluation procedure of software safety plan for digital I and C of KNGR

International Nuclear Information System (INIS)

Lee, Jang Soo; Park, Jong Kyun; Lee, Ki Young; Kwon, Ki Choon; Kim, Jang Yeol; Cheon, Se Woo

2000-05-01

The development, use, and regulation of computer systems in nuclear reactor instrumentation and control (I and C) systems to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Korean next generation reactor (KNGR) software safety verification and validation (SSVV) task, Korea Atomic Energy Research Institute, which investigates different aspects of computer software in reactor I and C systems, and describes the engineering procedures for developing such a software. The purpose of this guideline is to give the software safety evaluator the trail map between the code and standards layer and the design methodology and documents layer for the software important to safety in nuclear power plants. Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organizations. The requirements for software important to safety of nuclear reactor are described in such positions and standards, for example, the new standard review plan (SRP), IEC 880 supplements, IEEE standard 1228-1994, IEEE standard 7-4.3.2-1993, and IAEA safety series No. 50-SG-D3 and D8. We presented the guidance for evaluating the safety plan of the software in the KNGR protection systems. The guideline consists of the regulatory requirements for software safety in chapter 2, the evaluation checklist of software safety plan in chapter3, and the evaluation results of KNGR software safety plan in chapter 4

Evaluation procedure of software safety plan for digital I and C of KNGR

Energy Technology Data Exchange (ETDEWEB)

Lee, Jang Soo; Park, Jong Kyun; Lee, Ki Young; Kwon, Ki Choon; Kim, Jang Yeol; Cheon, Se Woo

2000-05-01

The development, use, and regulation of computer systems in nuclear reactor instrumentation and control (I and C) systems to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Korean next generation reactor (KNGR) software safety verification and validation (SSVV) task, Korea Atomic Energy Research Institute, which investigates different aspects of computer software in reactor I and C systems, and describes the engineering procedures for developing such a software. The purpose of this guideline is to give the software safety evaluator the trail map between the code and standards layer and the design methodology and documents layer for the software important to safety in nuclear power plants. Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organizations. The requirements for software important to safety of nuclear reactor are described in such positions and standards, for example, the new standard review plan (SRP), IEC 880 supplements, IEEE standard 1228-1994, IEEE standard 7-4.3.2-1993, and IAEA safety series No. 50-SG-D3 and D8. We presented the guidance for evaluating the safety plan of the software in the KNGR protection systems. The guideline consists of the regulatory requirements for software safety in chapter 2, the evaluation checklist of software safety plan in chapter3, and the evaluation results of KNGR software safety plan in chapter 4.

Software Engineering Principles for Courseware Development.

Science.gov (United States)

Magel, Kenneth

1980-01-01

Courseware (computer based curriculum materials) development should follow the lessons learned by software engineers. The most important of 28 principles of software development presented here include a stress on human readability, the importance of early planning and analysis, the need for independent evaluation, and the need to be flexible.…

"SABER": A new software tool for radiotherapy treatment plan evaluation.

Science.gov (United States)

Zhao, Bo; Joiner, Michael C; Orton, Colin G; Burmeister, Jay

2010-11-01

Both spatial and biological information are necessary in order to perform true optimization of a treatment plan and for predicting clinical outcome. The goal of this work is to develop an enhanced treatment plan evaluation tool which incorporates biological parameters and retains spatial dose information. A software system is developed which provides biological plan evaluation with a novel combination of features. It incorporates hyper-radiosensitivity using the induced-repair model and applies the new concept of dose convolution filter (DCF) to simulate dose wash-out effects due to cell migration, bystander effect, and/or tissue motion during treatment. Further, the concept of spatial DVH (sDVH) is introduced to evaluate and potentially optimize the spatial dose distribution in the target volume. Finally, generalized equivalent uniform dose is derived from both the physical dose distribution (gEUD) and the distribution of equivalent dose in 2 Gy fractions (gEUD2) and the software provides three separate models for calculation of tumor control probability (TCP), normal tissue complication probability (NTCP), and probability of uncomplicated tumor control (P+). TCP, NTCP, and P+ are provided as a function of prescribed dose and multivariable TCP, NTCP, and P+ plots are provided to illustrate the dependence on individual parameters used to calculate these quantities. Ten plans from two clinical treatment sites are selected to test the three calculation models provided by this software. By retaining both spatial and biological information about the dose distribution, the software is able to distinguish features of radiotherapy treatment plans not discernible using commercial systems. Plans that have similar DVHs may have different spatial and biological characteristics and the application of novel tools such as sDVH and DCF within the software may substantially change the apparent plan quality or predicted plan metrics such as TCP and NTCP. For the cases examined

TMT approach to observatory software development process

Science.gov (United States)

Buur, Hanne; Subramaniam, Annapurni; Gillies, Kim; Dumas, Christophe; Bhatia, Ravinder

2016-07-01

The purpose of the Observatory Software System (OSW) is to integrate all software and hardware components of the Thirty Meter Telescope (TMT) to enable observations and data capture; thus it is a complex software system that is defined by four principal software subsystems: Common Software (CSW), Executive Software (ESW), Data Management System (DMS) and Science Operations Support System (SOSS), all of which have interdependencies with the observatory control systems and data acquisition systems. Therefore, the software development process and plan must consider dependencies to other subsystems, manage architecture, interfaces and design, manage software scope and complexity, and standardize and optimize use of resources and tools. Additionally, the TMT Observatory Software will largely be developed in India through TMT's workshare relationship with the India TMT Coordination Centre (ITCC) and use of Indian software industry vendors, which adds complexity and challenges to the software development process, communication and coordination of activities and priorities as well as measuring performance and managing quality and risk. The software project management challenge for the TMT OSW is thus a multi-faceted technical, managerial, communications and interpersonal relations challenge. The approach TMT is using to manage this multifaceted challenge is a combination of establishing an effective geographically distributed software team (Integrated Product Team) with strong project management and technical leadership provided by the TMT Project Office (PO) and the ITCC partner to manage plans, process, performance, risk and quality, and to facilitate effective communications; establishing an effective cross-functional software management team composed of stakeholders, OSW leadership and ITCC leadership to manage dependencies and software release plans, technical complexities and change to approved interfaces, architecture, design and tool set, and to facilitate

Software to support planning for future waste treatment, storage, transport, and disposal requirements

International Nuclear Information System (INIS)

Holter, G.M.; Shay, M.R.; Stiles, D.L.

1990-04-01

Planning for adequate and appropriate treatment, storage, transport and disposal of wastes to be generated or received in the future is a complex but critical task that can be significantly enhanced by the development and use of appropriate software. This paper describes a software system that has been developed at Pacific Northwest Laboratory to aid in such planning. The basic needs for such a system are outlined, and the approach adopted in developing the software is described. The individual components of the system, and their integration into a unified system, are discussed. Typical analytical applications of this type of software are summarized. Conclusions concerning the development of such software systems and the necessary supporting data are then presented. 2 figs

MCNP trademark Software Quality Assurance plan

International Nuclear Information System (INIS)

Abhold, H.M.; Hendricks, J.S.

1996-04-01

MCNP is a computer code that models the interaction of radiation with matter. MCNP is developed and maintained by the Transport Methods Group (XTM) of the Los Alamos National Laboratory (LANL). This plan describes the Software Quality Assurance (SQA) program applied to the code. The SQA program is consistent with the requirements of IEEE-730.1 and the guiding principles of ISO 900

Design for software a playbook for developers

CERN Document Server

Klimczak, Erik

2013-01-01

A unique resource to help software developers create a desirable user experience Today, top-flight software must feature a desirable user experience. This one-of-a-kind book creates a design process specifically for software, making it easy for developers who lack design background to create that compelling user experience. Appealing to both tech-savvy designers and creative-minded technologists, it establishes a hybrid discipline that will produce first-rate software. Illustrated in full color, it shows how to plan and visualize the design to create software that works on every l

Clinical trials radiotherapy treatment plan review software : is this the first quantified assessment

International Nuclear Information System (INIS)

Hatton, J.A.; Cornes, D.A.

2011-01-01

Full text: Clinical trials require robust quality assurance (QA) procedures to ensure commonality of all treatments, with independent reviews to assess compliance with trial protocols. All clinical trials tools, including QA software, require testing for validity and reliability. enabling inter- and intra-trial comparison. Unlike clinical radiotherapy treatment planning (RTP) systems, review software has no published guidelines. This study describes the design and development of a test suite to quantify the performance of review software in TROG clinical trials. Test areas are image handling and reconstruction; geometric accuracy; dosimetric accuracy; dose-volume histogram (DVH) calculation; display of plan parameters. TROG have developed tests for commissioning plan review software, assessed with SWAN 2.3, and CMS Elekta FocalPro. While image handling tests were based on published guidelines for RTP systems, dosimetric tests used the TROG QA case review requirements. Treatment plans represented systems of all manufacturers (Pinnacle, Eclipse, Xio and Oncentra) used in Australasian centres. The test suite identified areas for SW A software development, including the DVH algorithm, changed to reduce calculation time. Results, in Fig. I, for known volumes of varying shapes and sizes, demonstrate differences between SWAN 2.1 and 2.3 when compared with Eclipse. Liaison with SWAN programmers enabled re-instatement of 2.1 algorithm. The test suite has quantified the RTP review software, prioritised areas for development with the programmers, and improved the user experience.

Configuration management plan. System definition and project development. Repository Based Software Engineering (RBSE) program

Science.gov (United States)

Mckay, Charles

1991-01-01

This is the configuration management Plan for the AdaNet Repository Based Software Engineering (RBSE) contract. This document establishes the requirements and activities needed to ensure that the products developed for the AdaNet RBSE contract are accurately identified, that proposed changes to the product are systematically evaluated and controlled, that the status of all change activity is known at all times, and that the product achieves its functional performance requirements and is accurately documented.

Project W-211, initial tank retrieval systems, retrieval control system software configuration management plan

International Nuclear Information System (INIS)

RIECK, C.A.

1999-01-01

This Software Configuration Management Plan (SCMP) provides the instructions for change control of the W-211 Project, Retrieval Control System (RCS) software after initial approval/release but prior to the transfer of custody to the waste tank operations contractor. This plan applies to the W-211 system software developed by the project, consisting of the computer human-machine interface (HMI) and programmable logic controller (PLC) software source and executable code, for production use by the waste tank operations contractor. The plan encompasses that portion of the W-211 RCS software represented on project-specific AUTOCAD drawings that are released as part of the C1 definitive design package (these drawings are identified on the drawing list associated with each C-1 package), and the associated software code. Implementation of the plan is required for formal acceptance testing and production release. The software configuration management plan does not apply to reports and data generated by the software except where specifically identified. Control of information produced by the software once it has been transferred for operation is the responsibility of the receiving organization

Programming language concepts for software developers

DEFF Research Database (Denmark)

Sestoft, Peter

2008-01-01

This note describes and motivates our current plans for an undergraduate course on programming language concepts for software development students. We describe the competences we expect students to acquire as well as the topics covered by the course. We plan to use C# and Scheme as instruction...

Software for project-based learning of robot motion planning

Science.gov (United States)

Moll, Mark; Bordeaux, Janice; Kavraki, Lydia E.

2013-12-01

Motion planning is a core problem in robotics concerned with finding feasible paths for a given robot. Motion planning algorithms perform a search in the high-dimensional continuous space of robot configurations and exemplify many of the core algorithmic concepts of search algorithms and associated data structures. Motion planning algorithms can be explained in a simplified two-dimensional setting, but this masks many of the subtleties and complexities of the underlying problem. We have developed software for project-based learning of motion planning that enables deep learning. The projects that we have developed allow advanced undergraduate students and graduate students to reflect on the performance of existing textbook algorithms and their own variations on such algorithms. Formative assessment has been conducted at three institutions. The core of the software used for this teaching module is also used within the Robot Operating System, a widely adopted platform by the robotics research community. This allows for transfer of knowledge and skills to robotics research projects involving a large variety robot hardware platforms.

A Study on the Software Quality Assurance Plan

International Nuclear Information System (INIS)

Kim, Hyun Tae

2006-01-01

On 25 August 2006, the CMMI V1.2 (Capability Maturity Model Integration Version 1.2) was released with the new title CMMI-DEV (CMMI for Development) which supersedes the CMMI-SE/SW (CMMI for systems engineering and software engineering) V1.1. This study discusses the application of IEEE Std 730-2002, IEEE Standard for Software Quality Assurance Plans, for the implementation of the Process and Product Quality Assurance (PPQA) process area (PA) of the CMMI-DEV

Software quality assurance plan for GCS

Science.gov (United States)

Duncan, Stephen E.; Bailey, Elizabeth K.

1990-01-01

The software quality assurance (SQA) function for the Guidance and Control Software (GCS) project which is part of a software error studies research program is described. The SQA plan outlines all of the procedures, controls, and audits to be carried out by the SQA organization to ensure adherence to the policies, procedures, and standards for the GCS project.

Light Duty Utility Arm Software Test Plan

International Nuclear Information System (INIS)

Kiebel, G.R.

1995-01-01

This plan describes how validation testing of the software will be implemented for the integrated control and data acquisition system of the Light Duty Utility Arm System (LDUA). The purpose of LDUA software validation testing is to demonstrate and document that the LDUA software meets its software requirements specification

Prometheus Reactor I&C Software Development Methodology, for Action

Energy Technology Data Exchange (ETDEWEB)

T. Hamilton

2005-07-30

The purpose of this letter is to submit the Reactor Instrumentation and Control (I&C) software life cycle, development methodology, and programming language selections and rationale for project Prometheus to NR for approval. This letter also provides the draft Reactor I&C Software Development Process Manual and Reactor Module Software Development Plan to NR for information.

Study on Top-Down Estimation Method of Software Project Planning

Institute of Scientific and Technical Information of China (English)

ZHANG Jun-guang; L(U) Ting-jie; ZHAO Yu-mei

2006-01-01

This paper studies a new software project planning method under some actual project data in order to make software project plans more effective. From the perspective of system theory, our new method regards a software project plan as an associative unit for study. During a top-down estimation of a software project, Program Evaluation and Review Technique (PERT) method and analogy method are combined to estimate its size, then effort estimation and specific schedules are obtained according to distributions of the phase effort. This allows a set of practical and feasible planning methods to be constructed. Actual data indicate that this set of methods can lead to effective software project planning.

Strategies for successful software development risk management

Directory of Open Access Journals (Sweden)

Marija Boban

2003-01-01

Full Text Available Nowadays, software is becoming a major part of enterprise business. Software development is activity connected with advanced technology and high level of knowledge. Risks on software development projects must be successfully mitigated to produce successful software systems. Lack of a defined approach to risk management is one of the common causes for project failures. To improve project chances for success, this work investigates common risk impact areas to perceive a foundation that can be used to define a common approach to software risk management. Based on typical risk impact areas on software development projects, we propose three risk management strategies suitable for a broad area of enterprises and software development projects with different amounts of connected risks. Proposed strategies define activities that should be performed for successful risk management, the one that will enable software development projects to perceive risks as soon as possible and to solve problems connected with risk materialization. We also propose a risk-based approach to software development planning and risk management as attempts to address and retire the highest impact risks as early as possible in the development process. Proposed strategies should improve risk management on software development projects and help create a successful software solution.

Formalizing the ISDF Software Development Methodology

Directory of Open Access Journals (Sweden)

Mihai Liviu DESPA

2015-01-01

Full Text Available The paper is aimed at depicting the ISDF software development methodology by emphasizing quality management and software development lifecycle. The ISDF methodology was built especially for innovative software development projects. The ISDF methodology was developed empirically by trial and error in the process of implementing multiple innovative projects. The research process began by analysing key concepts like innovation and software development and by settling the important dilemma of what makes a web application innovative. Innovation in software development is presented from the end-user, project owner and project manager’s point of view. The main components of a software development methodology are identified. Thus a software development methodology should account for people, roles, skills, teams, tools, techniques, processes, activities, standards, quality measuring tools, and team values. Current software development models are presented and briefly analysed. The need for a dedicated innovation oriented software development methodology is emphasized by highlighting shortcomings of current software development methodologies when tackling innovation. The ISDF methodology is presented in the context of developing an actual application. The ALHPA application is used as a case study for emphasizing the characteristics of the ISDF methodology. The development life cycle of the ISDF methodology includes research, planning, prototyping, design, development, testing, setup and maintenance. Artefacts generated by the ISDF methodology are presented. Quality is managed in the ISDF methodology by assessing compliance, usability, reliability, repeatability, availability and security. In order to properly asses each quality component a dedicated indicator is built. A template for interpreting each indicator is provided. Conclusions are formulated and new related research topics are submitted for debate.

AWARE-P: a collaborative, system-based IAM planning software

OpenAIRE

Coelho, S. T.; Vitorino, D.

2011-01-01

The AWARE-P project aims to promote the application of integrated and risk-based approaches to the rehabilitation of urban water supply and wastewater drainage systems. Central to the project is the development of a software platform based on a set of computational components, which assist in the analyses and decision support involved in the planning process for sustainable infrastructural asset management. The AWARE-P software system brings together onto a common platform the inf...

Developing a Treatment Planning Software Based on TG-43U1 Formalism for Cs-137 LDR Brachytherapy.

Science.gov (United States)

Sina, Sedigheh; Faghihi, Reza; Soleimani Meigooni, Ali; Siavashpour, Zahra; Mosleh-Shirazi, Mohammad Amin

2013-08-01

The old Treatment Planning Systems (TPSs) used for intracavitary brachytherapy with Cs-137 Selectron source utilize traditional dose calculation methods, considering each source as a point source. Using such methods introduces significant errors in dose estimation. As of 1995, TG-43 is used as the main dose calculation formalism in treatment TPSs. The purpose of this study is to design and establish a treatment planning software for Cs-137 Solectron brachytherapy source, based on TG-43U1 formalism by applying the effects of the applicator and dummy spacers. Two softwares used for treatment planning of Cs-137 sources in Iran (STPS and PLATO), are based on old formalisms. The purpose of this work is to establish and develop a TPS for Selectron source based on TG-43 formalism. In this planning system, the dosimetry parameters of each pellet in different places inside applicators were obtained by MCNP4c code. Then the dose distribution around every combination of active and inactive pellets was obtained by summing the doses. The accuracy of this algorithm was checked by comparing its results for special combination of active and inactive pellets with MC simulations. Finally, the uncertainty of old dose calculation formalism was investigated by comparing the results of STPS and PLATO softwares with those obtained by the new algorithm. For a typical arrangement of 10 active pellets in the applicator, the percentage difference between doses obtained by the new algorithm at 1cm distance from the tip of the applicator and those obtained by old formalisms is about 30%, while the difference between the results of MCNP and the new algorithm is less than 5%. According to the results, the old dosimetry formalisms, overestimate the dose especially towards the applicator's tip. While the TG-43U1 based software perform the calculations more accurately.

Software quality assurance plan for PORFLOW-3D

International Nuclear Information System (INIS)

Maheras, S.J.

1993-03-01

This plan describes the steps taken by the Idaho National Engineering Laboratory Subsurface and Environmental Modeling Unit personnel to implement software quality assurance procedures for the PORFLOW-3D computer code. PORFLOW-3D was used to conduct radiological performance assessments at the Savannah River Site. software quality assurance procedures for PORFLOW-3D include software acquisition, installation, testing, operation, maintenance, and retirement. Configuration control and quality assurance procedures are also included or referenced in this plan

Prometheus Reactor I and C Software Development Methodology, for Action

International Nuclear Information System (INIS)

T. Hamilton

2005-01-01

The purpose of this letter is to submit the Reactor Instrumentation and Control (I and C) software life cycle, development methodology, and programming language selections and rationale for project Prometheus to NR for approval. This letter also provides the draft Reactor I and C Software Development Process Manual and Reactor Module Software Development Plan to NR for information

Software quality assurance plan for the National Ignition Facility integrated computer control system

Energy Technology Data Exchange (ETDEWEB)

Woodruff, J.

1996-11-01

Quality achievement is the responsibility of the line organizations of the National Ignition Facility (NIF) Project. This Software Quality Assurance Plan (SQAP) applies to the activities of the Integrated Computer Control System (ICCS) organization and its subcontractors. The Plan describes the activities implemented by the ICCS section to achieve quality in the NIF Project`s controls software and implements the NIF Quality Assurance Program Plan (QAPP, NIF-95-499, L-15958-2) and the Department of Energy`s (DOE`s) Order 5700.6C. This SQAP governs the quality affecting activities associated with developing and deploying all control system software during the life cycle of the NIF Project.

Software quality assurance plan for the National Ignition Facility integrated computer control system

International Nuclear Information System (INIS)

Woodruff, J.

1996-11-01

Quality achievement is the responsibility of the line organizations of the National Ignition Facility (NIF) Project. This Software Quality Assurance Plan (SQAP) applies to the activities of the Integrated Computer Control System (ICCS) organization and its subcontractors. The Plan describes the activities implemented by the ICCS section to achieve quality in the NIF Project's controls software and implements the NIF Quality Assurance Program Plan (QAPP, NIF-95-499, L-15958-2) and the Department of Energy's (DOE's) Order 5700.6C. This SQAP governs the quality affecting activities associated with developing and deploying all control system software during the life cycle of the NIF Project

Small is beautiful: customer driven software development

DEFF Research Database (Denmark)

Hansen, Henrik A.B.; Koch, Christian; Pleman, Allan

1999-01-01

to develop their software. In small software houses operating in markets with complex products such as ERP (enterprise resource planning) systems, networking is necessary in order to gain the needed knowledge and resources in the production development process. Network is not seen as a magic word but leads......Summary form only given. The topics addressed in this paper is how networking can be used as a way for small software houses to enhances their innovative capabilities by using different kinds of collaboration in order to overcome the problems of lacking knowledge as well as resources in order...

Planning for land use and conservation: Assessing GIS-based conservation software for land use planning

Science.gov (United States)

Rob Baldwin; Ryan Scherzinger; Don Lipscomb; Miranda Mockrin; Susan Stein

2014-01-01

Recent advances in planning and ecological software make it possible to conduct highly technical analyses to prioritize conservation investments and inform local land use planning. We review these tools, termed conservation planning tools, and assess the knowledge of a key set of potential users: the land use planning community. We grouped several conservation software...

Order and chaos in agile software development: a comparison of two software development teams in a major IT company

OpenAIRE

Wang, Xiaofeng; Vidgen, Richard

2007-01-01

peer-reviewed Agile methods have emerged and become popular over last few years as a response to shortcomings of the waterfall process model. However, agile processes are stamped by some as chaotic processes and are placed in opposition to waterfall approaches. This paper uses the edge of chaos concept from complex adaptive systems theory as a theoretical lens to analyse the roles of structure and planning in the software development process. The software development processes ...

KAERI software safety guideline for developing safety-critical software in digital instrumentation and control system of nuclear power plant

International Nuclear Information System (INIS)

Lee, Jang Soo; Kim, Jang Yeol; Eum, Heung Seop.

1997-07-01

Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organization. The requirements for software important to safety of nuclear reactor are described in such positions and standards. Most of them are describing mandatory requirements, what shall be done, for the safety-critical software. The developers of such a software. However, there have been a lot of controversial factors on whether the work practices satisfy the regulatory requirements, and to justify the safety of such a system developed by the work practices, between the licenser and the licensee. We believe it is caused by the reason that there is a gap between the mandatory requirements (What) and the work practices (How). We have developed a guidance to fill such gap, which can be useful for both licenser and licensee to conduct a justification of the safety in the planning phase of developing the software for nuclear reactor protection systems. (author). 67 refs., 13 tabs., 2 figs

KAERI software safety guideline for developing safety-critical software in digital instrumentation and control system of nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Lee, Jang Soo; Kim, Jang Yeol; Eum, Heung Seop

1997-07-01

Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organization. The requirements for software important to safety of nuclear reactor are described in such positions and standards. Most of them are describing mandatory requirements, what shall be done, for the safety-critical software. The developers of such a software. However, there have been a lot of controversial factors on whether the work practices satisfy the regulatory requirements, and to justify the safety of such a system developed by the work practices, between the licenser and the licensee. We believe it is caused by the reason that there is a gap between the mandatory requirements (What) and the work practices (How). We have developed a guidance to fill such gap, which can be useful for both licenser and licensee to conduct a justification of the safety in the planning phase of developing the software for nuclear reactor protection systems. (author). 67 refs., 13 tabs., 2 figs.

KNGR core proection calculator, software, verification and validation plan

International Nuclear Information System (INIS)

Kim, Jang Yeol; Park, Jong Kyun; Lee, Ki Young; Lee, Jang Soo; Cheon, Se Woo

2001-05-01

This document describes the Software Verification and Validation Plan(SVVP) Guidance to be used in reviewing the Software Program Manual(SPM) in Korean Next Generation Reactor(KNGR) projects. This document is intended for a verifier or reviewer who is involved with performing of software verification and validation task activity in KNGR projects. This document includeds the basic philosophy, performing V and V effort, software testing techniques, criteria of review and audit on the safety software V and V activity. Major review topics on safety software addresses three kinds of characteristics based on Standard Review Plan(SRP) Chapter 7, Branch Technical Position(BTP)-14 : management characteristics, implementation characteristics and resources characteristics when reviewing on SVVP. Based on major topics of this document, we have produced the evaluation items list such as checklist in Appendix A

SWEPP gamma-ray spectrometer system software test plan and report

International Nuclear Information System (INIS)

Femec, D.A.

1994-09-01

The SWEPP Gamma-Ray Spectrometer (SGRS) System has been developed by the Radiation Measurements and Development Unit of the Idaho National Engineering Laboratory to assist in the characterization of the radiological contents of contact-handled waste containers at the Stored Waste Examination Pilot Plant (SWEPP). In addition to determining the concentrations of gamma-ray-emitting radionuclides, the software also calculates attenuation-corrected isotopic mass ratios of specific interest, and provides controls for SGRS hardware as required. This document presents the test plan and report for the data acquisition and analysis software associated with the SGRS system

Direct Integration: Training Software Developers to Conduct Usability Evaluations

DEFF Research Database (Denmark)

Skov, Mikael B.; Stage, Jan

2008-01-01

is based on an empirical study where 36 teams with a total of 234 first-year university students on software development and design educations were trained in a simple approach for user-based website usability testing that was taught in a 40 hour course. This approach supported them in planning, conducting......Many improvements of the interplay between usability evaluation and software development rely either on better methods for conducting usability evaluations or on better formats for presenting evaluation results in ways that are useful for software designers and developers. Both approaches involve...... a complete division of work between developers and evaluators, which is an undesirable complexity for many software development projects. This paper takes a different approach by exploring to what extent software developers and designers can be trained to carry out their own usability evaluations. The paper...

Adopting to Agile Software Development

Directory of Open Access Journals (Sweden)

Linkevics Gusts

2014-12-01

Full Text Available Agile software development can be made successful, but there is no well-defined way how to achieve this. The problem is that the successful adoption of agile methods and practices is a complex process and this process should be customizable for a particular organization or a team. This research focuses on identification of agile methods and practices. Result of the research is the ranking of agile methods, practices and their usage trends. As some terms of agile software development are interpreted differently in different organizations and teams, terminology used is analyzed. Results of the research can be used as a reference material for those who are planning to adopt agile methods or are looking for the next agile practice to implement. Results will be used for the development of an expert system to support agile adoption.

Qualified software development methodologies for nuclear class 1E equipment

International Nuclear Information System (INIS)

Koch, Shlomo; Ruether, J.

1992-01-01

This article describes the experience learned at Northern States Power and Spectrum Technologies, during the development of a computer based Safeguard Load Sequencer, for Prairie Island Nuclear Generating Plant. The Safeguard Load Sequencer (SLS) performs the function of 4kV emergency bus voltage restoration, load shedding, and emergency diesel generator loading. The system is designed around an Allen-Bradley PLC-5 programmable controller. The Safeguard Load Sequencer is the vehicle to demonstrate the software engineering procedures and methodologies. The article analyzes the requirements imposed by the NUREG 4640 handbook, and the relevant IEEE standards. The article tries to answer the question what is software engineering, and describe the waterfall life cycle phases of software development. The effects of each phase on software quality and V and V plan is described. Issues designing a V and V plan is addressed, and considerations of cost and time to implement the program are described. The article also addresses the subject of tools that can increase productivity and reduce the cost and time of an extensive V and V plan. It describes the tools the authors used, and more importantly presents a wish list of tools that they as developers would like to have. The role of testing is presented. They show that testing at the final stage has a lower impact on software quality then generally assumed. Full coverage of testing is almost always impossible, and they demonstrate how alternative audits and test during the development phase can improve software reliability

Configuration management plan for the GENII software

International Nuclear Information System (INIS)

Rittmann, P.D.

1994-01-01

The GENII program calculates doses from radionuclides released into the environment for a variety of possible exposure scenarios. The user prepares an input data file with the necessary modelling assumptions and parameters. The program reads the user's input file, computes the necessary doses and stores these results in an output file. The output file also contains a listing of the user's input and gives the title lines from the data libraries which are accessed in the course of the calculations. The purpose of this document is to provide users of the GENII software with the configuration controls which are planned for use by WHC in accordance with WHC-CM-3-10. The controls are solely for WHC employees. Non-WHC individuals are not excluded, but no promise is made or implied that they will be informed of errors or revisions to the software. The configuration controls cover the GENII software, the GENII user's guide, the list of GENII users at WHC, and the backup copies. Revisions to the software must be approved prior to distribution in accordance with this configuration management plan

Software configuration management plan, 241-AY and 241-AZ tank farm MICON automation system

International Nuclear Information System (INIS)

Hill, L.F.

1997-01-01

This document establishes a Computer Software Configuration Management Plan (CSCM) for controlling software for the MICON Distributed Control System (DCS) located at the 241-AY and 241-AZ Aging Waste Tank Farm facilities in the 200 East Area. The MICON DCS software controls and monitors the instrumentation and equipment associated with plant systems and processes. A CSCM identifies and defines the configuration items in a system (section 3.1), controls the release and change of these items throughout the system life cycle (section 3.2), records and reports the status of configuration items and change requests (section 3.3), and verifies the completeness and correctness of the items (section 3.4). All software development before initial release, or before software is baselined, is considered developmental. This plan does not apply to developmental software. This plan applies to software that has been baselined and released. The MICON software will monitor and control the related instrumentation and equipment of the 241-AY and 241-AZ Tank Farm ventilation systems. Eventually, this software may also assume the monitoring and control of the tank sludge washing equipment and other systems as they are brought on line. This plan applies to the System Cognizant Manager and MICON Cognizant Engineer (who is also referred to herein as the system administrator) responsible for the software/hardware and administration of the MICON system. This document also applies to any other organizations within Tank Farms which are currently active on the system including system cognizant engineers, nuclear operators, technicians, and control room supervisors

Light Duty Utility Arm computer software configuration management plan

International Nuclear Information System (INIS)

Philipp, B.L.

1998-01-01

This plan describes the configuration management for the Light Duty Utility Arm robotic manipulation arm control software. It identifies the requirement, associated documents, and the software control methodology. The Light Duty Utility Ann (LDUA) System is a multi-axis robotic manipulator arm and deployment vehicle, used to perform surveillance and characterization operations in support of remediation of defense nuclear wastes currently stored in the Hanford Underground Storage Tanks (USTs) through the available 30.5 cm (12 in.) risers. This plan describes the configuration management of the LDUA software

Software for CATV Design and Frequency Plan Optimization

OpenAIRE

Hala, O.

2007-01-01

The paper deals with the structure of a software medium used for design and sub-optimization of frequency plan in CATV networks, their description and design method. The software performance is described and a simple design example of energy balance of a simplified CATV network is given. The software was created in programming environment called Delphi and local optimization was made in Matlab.

Software components for medical image visualization and surgical planning

Science.gov (United States)

Starreveld, Yves P.; Gobbi, David G.; Finnis, Kirk; Peters, Terence M.

2001-05-01

Purpose: The development of new applications in medical image visualization and surgical planning requires the completion of many common tasks such as image reading and re-sampling, segmentation, volume rendering, and surface display. Intra-operative use requires an interface to a tracking system and image registration, and the application requires basic, easy to understand user interface components. Rapid changes in computer and end-application hardware, as well as in operating systems and network environments make it desirable to have a hardware and operating system as an independent collection of reusable software components that can be assembled rapidly to prototype new applications. Methods: Using the OpenGL based Visualization Toolkit as a base, we have developed a set of components that implement the above mentioned tasks. The components are written in both C++ and Python, but all are accessible from Python, a byte compiled scripting language. The components have been used on the Red Hat Linux, Silicon Graphics Iris, Microsoft Windows, and Apple OS X platforms. Rigorous object-oriented software design methods have been applied to ensure hardware independence and a standard application programming interface (API). There are components to acquire, display, and register images from MRI, MRA, CT, Computed Rotational Angiography (CRA), Digital Subtraction Angiography (DSA), 2D and 3D ultrasound, video and physiological recordings. Interfaces to various tracking systems for intra-operative use have also been implemented. Results: The described components have been implemented and tested. To date they have been used to create image manipulation and viewing tools, a deep brain functional atlas, a 3D ultrasound acquisition and display platform, a prototype minimally invasive robotic coronary artery bypass graft planning system, a tracked neuro-endoscope guidance system and a frame-based stereotaxy neurosurgery planning tool. The frame-based stereotaxy module has been

Software engineering architecture-driven software development

CERN Document Server

Schmidt, Richard F

2013-01-01

Software Engineering: Architecture-driven Software Development is the first comprehensive guide to the underlying skills embodied in the IEEE's Software Engineering Body of Knowledge (SWEBOK) standard. Standards expert Richard Schmidt explains the traditional software engineering practices recognized for developing projects for government or corporate systems. Software engineering education often lacks standardization, with many institutions focusing on implementation rather than design as it impacts product architecture. Many graduates join the workforce with incomplete skil

Software for CATV Design and Frequency Plan Optimization

Directory of Open Access Journals (Sweden)

O. Hala

2007-09-01

Full Text Available The paper deals with the structure of a software medium used for design and sub-optimization of frequency plan in CATV networks, their description and design method. The software performance is described and a simple design example of energy balance of a simplified CATV network is given. The software was created in programming environment called Delphi and local optimization was made in Matlab.

Acceptance Test Plan for ANSYS Software

International Nuclear Information System (INIS)

CREA, B.A.

2000-01-01

This plan governs the acceptance testing of the ANSYS software (Full Mechanical Release 5.5) for use on Project Word Management Contract (PHMC) computer systems (either UNIX or Microsoft Windows/NT). There are two phases to the acceptance testing covered by this test plan: program execution in accordance with the guidance provided in installation manuals; and ensuring results of the execution are consistent with the expected physical behavior of the system being modeled

Agile Software Development

Science.gov (United States)

Biju, Soly Mathew

2008-01-01

Many software development firms are now adopting the agile software development method. This method involves the customer at every level of software development, thus reducing the impact of change in the requirement at a later stage. In this article, the principles of the agile method for software development are explored and there is a focus on…

A software tool for advanced MRgFUS prostate therapy planning and follow up

Science.gov (United States)

van Straaten, Dörte; Hoogenboom, Martijn; van Amerongen, Martinus J.; Weiler, Florian; Issawi, Jumana Al; Günther, Matthias; Fütterer, Jurgen; Jenne, Jürgen W.

2017-03-01

US guided HIFU/FUS ablation for the therapy of prostate cancer is a clinical established method, while MR guided HIFU/FUS applications for prostate recently started clinical evaluation. Even if MRI examination is an excellent diagnostic tool for prostate cancer, it is a time consuming procedure and not practicable within an MRgFUS therapy session. The aim of our ongoing work is to develop software to support therapy planning and post-therapy follow-up for MRgFUS on localized prostate cancer, based on multi-parametric MR protocols. The clinical workflow of diagnosis, therapy and follow-up of MR guided FUS on prostate cancer was deeply analyzed. Based on this, the image processing workflow was designed and all necessary components, e.g. GUI, viewer, registration tools etc. were defined and implemented. The software bases on MeVisLab with several implemented C++ modules for the image processing tasks. The developed software, called LTC (Local Therapy Control) will register and visualize automatically all images (T1w, T2w, DWI etc.) and ADC or perfusion maps gained from the diagnostic MRI session. This maximum of diagnostic information helps to segment all necessary ROIs, e.g. the tumor, for therapy planning. Final therapy planning will be performed based on these segmentation data in the following MRgFUS therapy session. In addition, the developed software should help to evaluate the therapy success, by synchronization and display of pre-therapeutic, therapy and follow-up image data including the therapy plan and thermal dose information. In this ongoing project, the first stand-alone prototype was completed and will be clinically evaluated.

Development of a software of VMAT delivery using EPID

International Nuclear Information System (INIS)

Arumugam, Sankar; Xing, Aitang; Jameson, Michael; Holloway, Lois; Goozee, Gary

2011-01-01

Full text: Volumetric Modulated Arc Therapy (VMAT) is more complex than standard IMRT, requiring new methodology to evaluate delivery accuracy. Here, we present the development of methodology and a software tool to perform control point based verification of VMAT delivery using an EPID. Individual segment dose comparison allows the verification of VMAT deli very accuracy for individual control-points. An in-house software tool was developed to predict the individual segment dose as measured by EPID for Pinnacle (Philips) generated VMAT plans. The VMAT plans were delivered using an Elekta-synergy accelerator and the segment doses were measured using EPID. A normalised dose comparison of measured and predicted doses was performed using gamma analysis with 3% dose tolerance and 3 mm DTA. The sensitivity of the proposed methodology in detecting delivery errors was studied by delivering a standard intensity pattern with a preset dose error of 4 and 5% in two of its eight control-points. Four clinical plans were also tested using this methodology. The developed software accurately predicts the EPID dose by considering all possible leaf trajectories in VMAT delivery. The mean gamma value and percentage of pixels exceeding the gamma tolerance for a segment with and without delivery errors are shown in Table. From the tabulated values it is evident that the proposed methodology is sensitive in detecting delivery errors above 3% tolerance level. The clinical plans were successfully validated showing a maximum 2.5% of pixels exceeding gamma tolerance. Methodology and a software were successfully developed to perform control-point validation of VMAT delivery using an EPID. Set error in Delivery (%) Mean gamma value% of pixels exceeding Gamma tolerance 0 0.40 1.240.5417.050.6221.8.

Three-Dimensional Path Planning Software-Assisted Transjugular Intrahepatic Portosystemic Shunt: A Technical Modification

Energy Technology Data Exchange (ETDEWEB)

Tsauo, Jiaywei, E-mail: 80732059@qq.com; Luo, Xuefeng, E-mail: luobo-913@126.com [West China Hospital of Sichuan University, Institute of Interventional Radiology (China); Ye, Linchao, E-mail: linchao.ye@siemens.com [Siemens Ltd, Healthcare Sector (China); Li, Xiao, E-mail: simonlixiao@gmail.com [West China Hospital of Sichuan University, Institute of Interventional Radiology (China)

2015-06-15

PurposeThis study was designed to report our results with a modified technique of three-dimensional (3D) path planning software assisted transjugular intrahepatic portosystemic shunt (TIPS).Methods3D path planning software was recently developed to facilitate TIPS creation by using two carbon dioxide portograms acquired at least 20° apart to generate a 3D path for overlay needle guidance. However, one shortcoming is that puncturing along the overlay would be technically impossible if the angle of the liver access set and the angle of the 3D path are not the same. To solve this problem, a prototype 3D path planning software was fitted with a utility to calculate the angle of the 3D path. Using this, we modified the angle of the liver access set accordingly during the procedure in ten patients.ResultsFailure for technical reasons occurred in three patients (unsuccessful wedged hepatic venography in two cases, software technical failure in one case). The procedure was successful in the remaining seven patients, and only one needle pass was required to obtain portal vein access in each case. The course of puncture was comparable to the 3D path in all patients. No procedure-related complication occurred following the procedures.ConclusionsAdjusting the angle of the liver access set to match the angle of the 3D path determined by the software appears to be a favorable modification to the technique of 3D path planning software assisted TIPS.

Enterprise Architecture Planning in developing A planning Information System: a Case Study of Semarang State University

Directory of Open Access Journals (Sweden)

Budiman Kholiq

2018-01-01

Full Text Available This research has applied an integrated design and development of planning information system, which is been designed using Enterprise Architecture Planning. Frequent discrepancy between planning and realization of the budget that has been made, resulted in ineffective planning, is one of the reason for doing this research. The design using EAP aims to keep development aligned and in line with the strategic direction of the organization. In the practice, EAP is carried out in several stages of the planning initiation, identification and definition of business functions, proceeded with architectural design and EA implementation plan that has been built. In addition to the design of the Enterprise Architecture, this research carried out the implementation, and was tested by several methods of black box and white box. Black box testing method is used to test the fundamental aspects of the software, tested by two kinds of testing, first is using User Acceptance Testing and the second is using software functionality testing. White box testing method is used to test the effectiveness of the code in the software, tested using unit testing. Tests conducted using white box and black box on the integrated planning information system, is declared successful. Success in the software testing can not be ascertained if the software built has not shown any distinction from prior circumstance to the development of this integrated planning information system. For ensuring the success of this system implementation, the authors test consistency between the planning of data and the realization of prior-use of the information system, until after-use information system. This consistency test is done by reducing the time data of the planning and realization time. From the tabulated data, the planning information system that has been built reduces the difference between the planning time and the realization time, in which indicates that the planning information system

Enterprise Architecture Planning in developing A planning Information System: a Case Study of Semarang State University

Science.gov (United States)

Budiman, Kholiq; Prahasto, Toni; Kusumawardhani, Amie

2018-02-01

This research has applied an integrated design and development of planning information system, which is been designed using Enterprise Architecture Planning. Frequent discrepancy between planning and realization of the budget that has been made, resulted in ineffective planning, is one of the reason for doing this research. The design using EAP aims to keep development aligned and in line with the strategic direction of the organization. In the practice, EAP is carried out in several stages of the planning initiation, identification and definition of business functions, proceeded with architectural design and EA implementation plan that has been built. In addition to the design of the Enterprise Architecture, this research carried out the implementation, and was tested by several methods of black box and white box. Black box testing method is used to test the fundamental aspects of the software, tested by two kinds of testing, first is using User Acceptance Testing and the second is using software functionality testing. White box testing method is used to test the effectiveness of the code in the software, tested using unit testing. Tests conducted using white box and black box on the integrated planning information system, is declared successful. Success in the software testing can not be ascertained if the software built has not shown any distinction from prior circumstance to the development of this integrated planning information system. For ensuring the success of this system implementation, the authors test consistency between the planning of data and the realization of prior-use of the information system, until after-use information system. This consistency test is done by reducing the time data of the planning and realization time. From the tabulated data, the planning information system that has been built reduces the difference between the planning time and the realization time, in which indicates that the planning information system can motivate the

SAPHIRE 8 Software Quality Assurance Plan

Energy Technology Data Exchange (ETDEWEB)

Curtis Smith

2010-02-01

This Quality Assurance (QA) Plan documents the QA activities that will be managed by the INL related to JCN N6423. The NRC developed the SAPHIRE computer code for performing probabilistic risk assessments (PRAs) using a personal computer (PC) at the Idaho National Laboratory (INL) under Job Code Number (JCN) L1429. SAPHIRE started out as a feasibility study for a PRA code to be run on a desktop personal PC and evolved through several phases into a state-of-the-art PRA code. The developmental activity of SAPHIRE was the result of two concurrent important events: The tremendous expansion of PC software and hardware capability of the 90s and the onset of a risk-informed regulation era.

Software Configuration Management Plan for the Sodium Removal System

International Nuclear Information System (INIS)

HILL, L.F.

2000-01-01

This document establishers the Software Configuration Management Plan (SCMP) for the software associated with the control system of the Sodium Removal System (SRS) located in the Interim Examination and Maintenance (IEM Cell) Facility of the FFTF Flux Test

Coordinating Management Activities in Distributed Software Development Projects

OpenAIRE

Bendeck, Fawsy; Goldmann, Sigrid; Holz, Harald; Kötting, Boris

1999-01-01

Coordinating distributed processes, especially engineering and software design processes, has been a research topic for some time now. Several approaches have been published that aim at coordinating large projects in general, and large software development processes in specific. However, most of these approaches focus on the technical part of the design process and omit management activities like planning and scheduling the project, or monitoring it during execution. In this paper, we focus o...

Preliminary experience with SpineEOS, a new software for 3D planning in AIS surgery.

Science.gov (United States)

Ferrero, Emmanuelle; Mazda, Keyvan; Simon, Anne-Laure; Ilharreborde, Brice

2018-04-24

Preoperative planning of scoliosis surgery is essential in the effective treatment of spine pathology. Thus, precontoured rods have been recently developed to avoid iatrogenic sagittal misalignment and rod breakage. Some specific issues exist in adolescent idiopathic scoliosis (AIS), such as a less distal lower instrumented level, a great variability in the location of inflection point (transition from lumbar lordosis to thoracic kyphosis), and sagittal correction is limited by both bone-implant interface. Since 2007, stereoradiographic imaging system is used and allows for 3D reconstructions. Therefore, a software was developed to perform preoperative 3D surgical planning and to provide rod's shape and length. The goal of this preliminary study was to assess the feasibility, reliability, and the clinical relevance of this new software. Retrospective study on 47 AIS patients operated with the same surgical technique: posteromedial translation through posterior approach with lumbar screws and thoracic sublaminar bands. Pre- and postoperatively, 3D reconstructions were performed on stereoradiographic images (EOS system, Paris, France) and compared. Then, the software was used to plan the surgical correction and determine rod's shape and length. Simulated spine and rods were compared to postoperative real 3D reconstructions. 3D reconstructions and planning were performed by an independent observer. 3D simulations were performed on the 47 patients. No difference was found between the simulated model and the postoperative 3D reconstructions in terms of sagittal parameters. Postoperatively, 21% of LL were not within reference values. Postoperative SVA was 20 mm anterior in 2/3 of the cases. Postoperative rods were significantly longer than precontoured rods planned with the software (mean 10 mm). Inflection points were different on the rods used and the planned rods (2.3 levels on average). In this preliminary study, the software based on 3D stereoradiography low

Management of Software Development Projects

Directory of Open Access Journals (Sweden)

Felician ALECU

2011-04-01

Full Text Available Any major software development starts with the Initiating process group. Once the charter document is approved, the Planning and then to the Executing stages will follow. Monitoring and Controlling is measuring the potential performance deviation of the project in terms of schedule and costs and performs the related Integrated Change Control activities. At the end, during the Closing, the program/project manager will check the entire work is completed and the objectives are met.

PLANNING QUALITY ASSURANCE PROCESSES IN A LARGE SCALE GEOGRAPHICALLY SPREAD HYBRID SOFTWARE DEVELOPMENT PROJECT

Directory of Open Access Journals (Sweden)

Святослав Аркадійович МУРАВЕЦЬКИЙ

2016-02-01

Full Text Available There have been discussed key points of operational activates in a large scale geographically spread software development projects. A look taken at required QA processes structure in such project. There have been given up to date methods of integration quality assurance processes into software development processes. There have been reviewed existing groups of software development methodologies. Such as sequential, agile and based on RPINCE2. There have been given a condensed overview of quality assurance processes in each group. There have been given a review of common challenges that sequential and agile models are having in case of large geographically spread hybrid software development project. Recommendations were given in order to tackle those challenges.  The conclusions about the best methodology choice and appliance to the particular project have been made.

A Development Framework for Software Security in Nuclear Safety Systems: Integrating Secure Development and System Security Activities

Energy Technology Data Exchange (ETDEWEB)

Park, Jaekwan; Suh, Yongsuk [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-02-15

The protection of nuclear safety software is essential in that a failure can result in significant economic loss and physical damage to the public. However, software security has often been ignored in nuclear safety software development. To enforce security considerations, nuclear regulator commission recently issued and revised the security regulations for nuclear computer-based systems. It is a great challenge for nuclear developers to comply with the security requirements. However, there is still no clear software development process regarding security activities. This paper proposes an integrated development process suitable for the secure development requirements and system security requirements described by various regulatory bodies. It provides a three-stage framework with eight security activities as the software development process. Detailed descriptions are useful for software developers and licensees to understand the regulatory requirements and to establish a detailed activity plan for software design and engineering.

KAERI software verification and validation guideline for developing safety-critical software in digital I and C system of NPP

Energy Technology Data Exchange (ETDEWEB)

Kim, Jang Yeol; Lee, Jang Soo; Eom, Heung Seop

1997-07-01

This technical report is to present V and V guideline development methodology for safety-critical software in NPP safety system. Therefore it is to present V and V guideline of planning phase for the NPP safety system in addition to critical safety items, for example, independence philosophy, software safety analysis concept, commercial off the shelf (COTS) software evaluation criteria, inter-relationships between other safety assurance organizations, including the concepts of existing industrial standard, IEEE Std-1012, IEEE Std-1059. This technical report includes scope of V and V guideline, guideline framework as part of acceptance criteria, V and V activities and task entrance as part of V and V activity and exit criteria, review and audit, testing and QA records of V and V material and configuration management, software verification and validation plan production etc., and safety-critical software V and V methodology. (author). 11 refs.

KAERI software verification and validation guideline for developing safety-critical software in digital I and C system of NPP

International Nuclear Information System (INIS)

Kim, Jang Yeol; Lee, Jang Soo; Eom, Heung Seop.

1997-07-01

This technical report is to present V and V guideline development methodology for safety-critical software in NPP safety system. Therefore it is to present V and V guideline of planning phase for the NPP safety system in addition to critical safety items, for example, independence philosophy, software safety analysis concept, commercial off the shelf (COTS) software evaluation criteria, inter-relationships between other safety assurance organizations, including the concepts of existing industrial standard, IEEE Std-1012, IEEE Std-1059. This technical report includes scope of V and V guideline, guideline framework as part of acceptance criteria, V and V activities and task entrance as part of V and V activity and exit criteria, review and audit, testing and QA records of V and V material and configuration management, software verification and validation plan production etc., and safety-critical software V and V methodology. (author). 11 refs

Exploring Coordination Structures in Open Source Software Development

NARCIS (Netherlands)

van Hillegersberg, Jos; Harmsen, Frank; Hegeman, J.H.; Amrit, Chintan Amrit; Geisberger, Eva; Keil, Patrick; Kuhrmann, Marco

2007-01-01

Coordination is difficult to achieve in a large globally distributed project setting. The problem is multiplied in open source software development projects, where most of the traditional means of coordination such as plans, system-level designs, schedules and defined process are not used. In order

Guidelines for evaluating software configuration management plans for digital instrumentation and control systems

International Nuclear Information System (INIS)

Cheon, Se Woo; Park, Jong Kyun; Lee, Ki Young; Lee, Jang Soo; Kim, Jang Yeon

2001-08-01

Software configuration management (SCM) is the process for identifying software configuration items (CIs), controlling the implementation and changes to software, recording and reporting the status of changes, and verifying the completeness and correctness of the released software. SCM consists of two major aspects: planning and implementation. Effective SCM involves planning for how activities are to be performed, and performing these activities in accordance with the Plan. This report first reviews the background of SCM that include key standards, SCM disciplines, SCM basic functions, baselines, software entity, SCM process, the implementation of SCM, and the tools of SCM. In turn, the report provides the guidelines for evaluating the SCM Plan for digital I and C systems of nuclear power plants. Most of the guidelines in the report are based on IEEE Std 828 and ANSI/IEEE Std 1042. According to BTP-14, NUREG-0800, the evaluation topics on the SCM Plan is classified into three categories: management, implementation, and resource characteristics

Sandia National Laboratories Advanced Simulation and Computing (ASC) software quality plan. Part 1: ASC software quality engineering practices, Version 2.0.

Energy Technology Data Exchange (ETDEWEB)

Sturtevant, Judith E.; Heaphy, Robert; Hodges, Ann Louise; Boucheron, Edward A.; Drake, Richard Roy; Minana, Molly A.; Hackney, Patricia; Forsythe, Christi A.; Schofield, Joseph Richard, Jr. (,; .); Pavlakos, Constantine James; Williamson, Charles Michael; Edwards, Harold Carter

2006-09-01

The purpose of the Sandia National Laboratories Advanced Simulation and Computing (ASC) Software Quality Plan is to clearly identify the practices that are the basis for continually improving the quality of ASC software products. The plan defines the ASC program software quality practices and provides mappings of these practices to Sandia Corporate Requirements CPR 1.3.2 and 1.3.6 and to a Department of Energy document, ASCI Software Quality Engineering: Goals, Principles, and Guidelines. This document also identifies ASC management and software project teams responsibilities in implementing the software quality practices and in assessing progress towards achieving their software quality goals.

FY95 software project management plan: TMACS, CASS computer systems

International Nuclear Information System (INIS)

Spurling, D.G.

1994-01-01

The FY95 Work Plan for TMACS and CASS Software Projects describes the activities planned for the current fiscal year. This plan replaces WHC-SD-WM-SDP-008. The TMACS project schedule is included in the TWRS Integrated Schedule

Developing Software Simulations

Directory of Open Access Journals (Sweden)

Tom Hall

2007-06-01

Full Text Available Programs in education and business often require learners to develop and demonstrate competence in specified areas and then be able to effectively apply this knowledge. One method to aid in developing a skill set in these areas is through the use of software simulations. These simulations can be used for learner demonstrations of competencies in a specified course as well as a review of the basic skills at the beginning of subsequent courses. The first section of this paper discusses ToolBook, the software used to develop our software simulations. The second section discusses the process of developing software simulations. The third part discusses how we have used software simulations to assess student knowledge of research design by providing simulations that allow the student to practice using SPSS and Excel.

Repository-Based Software Engineering Program: Working Program Management Plan

Science.gov (United States)

1993-01-01

Repository-Based Software Engineering Program (RBSE) is a National Aeronautics and Space Administration (NASA) sponsored program dedicated to introducing and supporting common, effective approaches to software engineering practices. The process of conceiving, designing, building, and maintaining software systems by using existing software assets that are stored in a specialized operational reuse library or repository, accessible to system designers, is the foundation of the program. In addition to operating a software repository, RBSE promotes (1) software engineering technology transfer, (2) academic and instructional support of reuse programs, (3) the use of common software engineering standards and practices, (4) software reuse technology research, and (5) interoperability between reuse libraries. This Program Management Plan (PMP) is intended to communicate program goals and objectives, describe major work areas, and define a management report and control process. This process will assist the Program Manager, University of Houston at Clear Lake (UHCL) in tracking work progress and describing major program activities to NASA management. The goal of this PMP is to make managing the RBSE program a relatively easy process that improves the work of all team members. The PMP describes work areas addressed and work efforts being accomplished by the program; however, it is not intended as a complete description of the program. Its focus is on providing management tools and management processes for monitoring, evaluating, and administering the program; and it includes schedules for charting milestones and deliveries of program products. The PMP was developed by soliciting and obtaining guidance from appropriate program participants, analyzing program management guidance, and reviewing related program management documents.

Space Flight Software Development Software for Intelligent System Health Management

Science.gov (United States)

Trevino, Luis C.; Crumbley, Tim

2004-01-01

The slide presentation examines the Marshall Space Flight Center Flight Software Branch, including software development projects, mission critical space flight software development, software technical insight, advanced software development technologies, and continuous improvement in the software development processes and methods.

An integrated approach for requirement selection and scheduling in software release planning

NARCIS (Netherlands)

Li, C.; van den Akker, Marjan; Brinkkemper, Sjaak; Diepen, Guido

2010-01-01

It is essential for product software companies to decide which requirements should be included in the next release and to make an appropriate time plan of the development project. Compared to the extensive research done on requirement selection, very little research has been performed on time

Gammasphere software development

International Nuclear Information System (INIS)

Piercey, R.B.

1994-01-01

This report describes the activities of the nuclear physics group at Mississippi State University which were performed during 1993. Significant progress has been made in the focus areas: chairing the Gammasphere Software Working Group (SWG); assisting with the porting and enhancement of the ORNL UPAK histogramming software package; and developing standard formats for Gammasphere data products. In addition, they have established a new public ftp archive to distribute software and software development tools and information

Self-service for software development projects and HPC activities

International Nuclear Information System (INIS)

Husejko, M; Høimyr, N; Gonzalez, A; Koloventzos, G; Asbury, D; Trzcinska, A; Agtzidis, I; Botrel, G; Otto, J

2014-01-01

This contribution describes how CERN has implemented several essential tools for agile software development processes, ranging from version control (Git) to issue tracking (Jira) and documentation (Wikis). Running such services in a large organisation like CERN requires many administrative actions both by users and service providers, such as creating software projects, managing access rights, users and groups, and performing tool-specific customisation. Dealing with these requests manually would be a time-consuming task. Another area of our CERN computing services that has required dedicated manual support has been clusters for specific user communities with special needs. Our aim is to move all our services to a layered approach, with server infrastructure running on the internal cloud computing infrastructure at CERN. This contribution illustrates how we plan to optimise the management of our of services by means of an end-user facing platform acting as a portal into all the related services for software projects, inspired by popular portals for open-source developments such as Sourceforge, GitHub and others. Furthermore, the contribution will discuss recent activities with tests and evaluations of High Performance Computing (HPC) applications on different hardware and software stacks, and plans to offer a dynamically scalable HPC service at CERN, based on affordable hardware.

Development and Demonstration of a Method to Evaluate Bio-Sampling Strategies Using Building Simulation and Sample Planning Software.

Science.gov (United States)

Dols, W Stuart; Persily, Andrew K; Morrow, Jayne B; Matzke, Brett D; Sego, Landon H; Nuffer, Lisa L; Pulsipher, Brent A

2010-01-01

In an effort to validate and demonstrate response and recovery sampling approaches and technologies, the U.S. Department of Homeland Security (DHS), along with several other agencies, have simulated a biothreat agent release within a facility at Idaho National Laboratory (INL) on two separate occasions in the fall of 2007 and the fall of 2008. Because these events constitute only two realizations of many possible scenarios, increased understanding of sampling strategies can be obtained by virtually examining a wide variety of release and dispersion scenarios using computer simulations. This research effort demonstrates the use of two software tools, CONTAM, developed by the National Institute of Standards and Technology (NIST), and Visual Sample Plan (VSP), developed by Pacific Northwest National Laboratory (PNNL). The CONTAM modeling software was used to virtually contaminate a model of the INL test building under various release and dissemination scenarios as well as a range of building design and operation parameters. The results of these CONTAM simulations were then used to investigate the relevance and performance of various sampling strategies using VSP. One of the fundamental outcomes of this project was the demonstration of how CONTAM and VSP can be used together to effectively develop sampling plans to support the various stages of response to an airborne chemical, biological, radiological, or nuclear event. Following such an event (or prior to an event), incident details and the conceptual site model could be used to create an ensemble of CONTAM simulations which model contaminant dispersion within a building. These predictions could then be used to identify priority area zones within the building and then sampling designs and strategies could be developed based on those zones.

Gammasphere software development

International Nuclear Information System (INIS)

Piercey, R.B.

1993-01-01

Activities of the nuclear physics group are described. Progress was made in organizing the Gammasphere Software Working Group, establishing a nuclear computing facility, participating in software development at Lawrence Berkeley, developing a common data file format, and adapting the ORNL UPAK software to run at Gammasphere. A universal histogram object was developed that defines a file format and provides for an objective-oriented programming model. An automated liquid nitrogen fill system was developed for Gammasphere (110 Ge detectors comprise the sphere)

Beyond Reactive Planning: Self Adaptive Software and Self Modeling Software in Predictive Deliberation Management

National Research Council Canada - National Science Library

Lenahan, Jack; Nash, Michael P; Charles, Phil

2008-01-01

.... We present the following hypothesis: predictive deliberation management using self-adapting and self-modeling software will be required to provide mission planning adjustments after the start of a mission...

[Development of integrated support software for clinical nutrition].

Science.gov (United States)

Siquier Homar, Pedro; Pinteño Blanco, Manel; Calleja Hernández, Miguel Ángel; Fernández Cortés, Francisco; Martínez Sotelo, Jesús

2015-09-01

to develop an integrated computer software application for specialized nutritional support, integrated in the electronic clinical record, which detects automatically and early those undernourished patients or at risk of developing undernourishment, determining points of opportunity for improvement and evaluation of the results. the quality standards published by the Nutrition Work Group of the Spanish Society of Hospital Pharmacy (SEFH) and the recommendations by the Pharmacy Group of the Spanish Society of Parenteral and Enteral Nutrition (SENPE) have been taken into account. According to these quality standards, the nutritional support has to include the following healthcare stages or sub-processes: nutritional screening, nutritional assessment, plan for nutritional care, prescription, preparation and administration. this software allows to conduct, in an automated way, a specific nutritional assessment for those patients with nutritional risk, implementing, if necessary, a nutritional treatment plan, conducting follow-up and traceability of outcomes derived from the implementation of improvement actions, and quantifying to what extent our practice is close to the established standard. this software allows to standardize the specialized nutritional support from a multidisciplinary point of view, introducing the concept of quality control per processes, and including patient as the main customer. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Development of integrated support software for clinical nutrition

Directory of Open Access Journals (Sweden)

Pedro Siquier Homar

2015-09-01

Full Text Available Objectives: to develop an integrated computer software application for specialized nutritional support, integrated in the electronic clinical record, which detects automatically and early those undernourished patients or at risk of developing undernourishment, determining points of opportunity for improvement and evaluation of the results. Methods: the quality standards published by the Nutrition Work Group of the Spanish Society of Hospital Pharmacy (SEFH and the recommendations by the Pharmacy Group of the Spanish Society of Parenteral and Enteral Nutrition (SENPE have been taken into account. According to these quality standards, the nutritional support has to include the following healthcare stages or sub-processes: nutritional screening, nutritional assessment, plan for nutritional care, prescription, preparation and administration. Results: this software allows to conduct, in an automated way, a specific nutritional assessment for those patients with nutritional risk, implementing, if necessary, a nutritional treatment plan, conducting follow-up and traceability of outcomes derived from the implementation of improvement actions, and quantifying to what extent our practice is close to the established standard. Conclusions: this software allows to standardize the specialized nutritional support from a multidisciplinary point of view, introducing the concept of quality control per processes, and including patient as the main customer

Recommendations for a Software Quality Assurance Plan for the CMR Facility at LANL

International Nuclear Information System (INIS)

Adams, K.; Matthews, S. D.; McQueen, M. A.

1998-01-01

The Nuclear Materials Technology (NMT) organizations 1 and 3 within the Chemical and Metallurgical Research (CMR) facility at the Los Alamos National Laboratory are working to achieve Waste Isolation Pilot Plant (WIPP) certification to enable them to transport their TRU waste to WIPP. This document is intended to provide not only recommendations to address the necessary software quality assurance activities to enable the NMT-1 and NMT-3 organizations to be WIPP compliant but is also meant to provide a template for the final Software Quality Assurance Plan (SQAP). This document specifically addresses software quality assurance for all software used in support of waste characterization and analysis. Since NMT-1 and NMT-3 currently have several operational software products that are used for waste characterization and analysis, these software quality assurance recommendations apply to the operations, maintenance and retirement of the software and the creation and development of any new software required for waste characterization and analyses

Software Quality Assurance activities of ITER CODAC

Energy Technology Data Exchange (ETDEWEB)

Pande, Sopan, E-mail: sopan.pande@iter.org [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul Lez Durance (France); DiMaio, Franck; Kim, Changseung; Kim, Joohan; Klotz, Wolf-Dieter; Makijarvi, Petri; Stepanov, Denis; Wallander, Anders [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul Lez Durance (France)

2013-10-15

Highlights: ► Comprehensive and consistent software engineering and quality assurance of CODAC. ► Applicable to all CODAC software projects executed by ITER DAs and contractors. ► Configurable plans for cost effective application of SQA processes. ► CODAC software plans SQAP, SVVP, SDP, and SCMP. ► CODAC software processes based on IEEE 12207-2008. -- Abstract: Software as an integral part of the plant system I and C is crucial in the manufacturing and integrated operation of ITER plant systems. Software Quality Assurance is necessary to ensure the development and maintenance of consistently high quality I and C software throughout the lifetime of ITER. CODAC decided to follow IEEE 12207-2008 software lifecycle processes for Software Engineering and Software Quality Assurance. Software Development Plan, Software Configuration Management Plan and Software Verification and Validation Plan are the mainstay of Software Quality Assurance which is documented in the Software Quality Assurance Plan. This paper describes the Software Quality Assurance (SQA) activities performed by CODAC. The SQA includes development and maintenance of above plans, processes and resources. With the help of Verification and Validation Teams they gather evidence of process conformance and product conformance, and record process data for quality audits and perform process improvements.

Software Quality Assurance activities of ITER CODAC

International Nuclear Information System (INIS)

Pande, Sopan; DiMaio, Franck; Kim, Changseung; Kim, Joohan; Klotz, Wolf-Dieter; Makijarvi, Petri; Stepanov, Denis; Wallander, Anders

2013-01-01

Highlights: ► Comprehensive and consistent software engineering and quality assurance of CODAC. ► Applicable to all CODAC software projects executed by ITER DAs and contractors. ► Configurable plans for cost effective application of SQA processes. ► CODAC software plans SQAP, SVVP, SDP, and SCMP. ► CODAC software processes based on IEEE 12207-2008. -- Abstract: Software as an integral part of the plant system I and C is crucial in the manufacturing and integrated operation of ITER plant systems. Software Quality Assurance is necessary to ensure the development and maintenance of consistently high quality I and C software throughout the lifetime of ITER. CODAC decided to follow IEEE 12207-2008 software lifecycle processes for Software Engineering and Software Quality Assurance. Software Development Plan, Software Configuration Management Plan and Software Verification and Validation Plan are the mainstay of Software Quality Assurance which is documented in the Software Quality Assurance Plan. This paper describes the Software Quality Assurance (SQA) activities performed by CODAC. The SQA includes development and maintenance of above plans, processes and resources. With the help of Verification and Validation Teams they gather evidence of process conformance and product conformance, and record process data for quality audits and perform process improvements

Improving Software Developer's Competence

DEFF Research Database (Denmark)

Abrahamsson, Pekka; Kautz, Karlheinz; Sieppi, Heikki

2002-01-01

Emerging agile software development methods are people oriented development approaches to be used by the software industry. The personal software process (PSP) is an accepted method for improving the capabilities of a single software engineer. Five original hypotheses regarding the impact...

Creating a strategic plan for configuration management using computer aided software engineering (CASE) tools

International Nuclear Information System (INIS)

Smith, P.R.; Sarfaty, R.

1993-01-01

This paper provides guidance in the definition, documentation, measurement, enhancement of processes, and validation of a strategic plan for configuration management (CM). The approach and methodology used in establishing a strategic plan is the same for any enterprise, including the Department of Energy (DOE), commercial nuclear plants, the Department of Defense (DOD), or large industrial complexes. The principles and techniques presented are used world wide by some of the largest corporations. The authors used industry knowledge and the areas of their current employment to illustrate and provide examples. Developing a strategic configuration and information management plan for DOE Idaho Field Office (DOE-ID) facilities is discussed in this paper. A good knowledge of CM principles is the key to successful strategic planning. This paper will describe and define CM elements, and discuss how CM integrates the facility's physical configuration, design basis, and documentation. The strategic plan does not need the support of a computer aided software engineering (CASE) tool. However, the use of the CASE tool provides a methodology for consistency in approach, graphics, and database capability combined to form an encyclopedia and a method of presentation that is easily understood and aids the process of reengineering. CASE tools have much more capability than those stated above. Some examples are supporting a joint application development group (JAD) to prepare a software functional specification document and, if necessary, provide the capability to automatically generate software application code. This paper briefly discusses characteristics and capabilities of two CASE tools that use different methodologies to generate similar deliverables

Package-based software development

NARCIS (Netherlands)

Jonge, de M.; Chroust, G.; Hofer, C.

2003-01-01

The main goal of component-based software engineering is to decrease development time and development costs of software systems, by reusing prefabricated building blocks. Here we focus on software reuse within the implementation of such component-based applications, and on the corresponding software

LDUA software custodian's notebook

International Nuclear Information System (INIS)

Aftanas, B.L.

1998-01-01

This plan describes the activities to be performed and controls to be applied to the process of specifying, obtaining, and qualifying the control and data acquisition software for the Light Duty Utility Arm (LDUA) System. It serves the purpose of a software quality assurance plan, a verification and validation plan, and a configuration management plan. This plan applies to all software that is an integral part of the LDUA control and data acquisition system, that is, software that is installed in the computers that are part of the LDUA system as it is deployed in the field. This plan applies to the entire development process, including: requirements; design; implementation; and operations and maintenance. This plan does not apply to any software that is not integral with the LDUA system. This plan has-been prepared in accordance with WHC-CM-6-1 Engineering Practices, EP-2.1; WHC-CM-3-10 Software Practices; and WHC-CM-4-2, QR 19.0, Software Quality Assurance Requirements

[Development of a Software for Automatically Generated Contours in Eclipse TPS].

Science.gov (United States)

Xie, Zhao; Hu, Jinyou; Zou, Lian; Zhang, Weisha; Zou, Yuxin; Luo, Kelin; Liu, Xiangxiang; Yu, Luxin

2015-03-01

The automatic generation of planning targets and auxiliary contours have achieved in Eclipse TPS 11.0. The scripting language autohotkey was used to develop a software for automatically generated contours in Eclipse TPS. This software is named Contour Auto Margin (CAM), which is composed of operational functions of contours, script generated visualization and script file operations. RESULTS Ten cases in different cancers have separately selected, in Eclipse TPS 11.0 scripts generated by the software could not only automatically generate contours but also do contour post-processing. For different cancers, there was no difference between automatically generated contours and manually created contours. The CAM is a user-friendly and powerful software, and can automatically generated contours fast in Eclipse TPS 11.0. With the help of CAM, it greatly save plan preparation time and improve working efficiency of radiation therapy physicists.

Sustainable embedded software lifecycle planning

OpenAIRE

Lee, Dong-Hyun; In, Hoh Peter; Lee, Keun; Park, Sooyong; Hinchey, Mike

2012-01-01

peer-reviewed Time-to-market is a crucial factor in increasing market share in the consumer electronics (CE) market. Furthermore, fierce competition in the market tends to sharply lower the prices of brand-new CE products as soon as they are released. Software-intensive embedded system design methods such as hardware/software co-design have been studied with the goal of reducing development lead-time by designing hardware and software simultaneously. Many researchers, however, concentra...

Systematic Software Development

DEFF Research Database (Denmark)

Kuhrmann, Marco; Méndez Fernández, Daniel

2015-01-01

The speed of innovation and the global allocation of resources to accelerate development or to reduce cost put pressure on the software industry. In the global competition, especially so-called high-price countries have to present arguments why the higher development cost is justified and what...... makes these countries an attractive host for software companies. Often, high-quality engineering and excellent quality of products, e.g., machinery and equipment, are mentioned. Yet, the question is: Can such arguments be also found for the software industry? We aim at investigating the degree...... of professionalism and systematization of software development to draw a map of strengths and weaknesses. To this end, we conducted as a first step an exploratory survey in Germany, presented in this paper. In this survey, we focused on the perceived importance of the two general software engineering process areas...

AWARE-P: a system-based software for urban water IAM planning

OpenAIRE

Coelho, S.T.; Vitorino, D.; Alegre, H.

2013-01-01

The AWARE-P IAM planning software offers a non-intrusive, web-based, collaborative integration environment for a wide variety of data and processes that may be relevant to the IAM decision-making process, including maps, GIS shapefiles and geodatabases; inventory records; work orders, maintenance, inspections/CCTV records; network models, performance indicators, asset valuation records, among others. The software provides an organized framework for evaluating and comparing planning alternativ...

A pioneering application of NQA-1 quality assurance standards in the development of software

International Nuclear Information System (INIS)

Weisbin, A.N.

1988-01-01

The application of NQA-1 Quality Assurance Standards to computer software programs has been recent at the Oak Ridge National Laboratory. One reason for systematically applying quality assurance to computer software is the extensive use of results from computer programs. to characterize potential sites for nuclear waste repositories leading ultimately to important policy making decisions. Because data from these programs characterize the likely radioactivity profile for many hundreds of years, experimental validation is not feasible. The Sensitivity and Uncertainty Analysis Methods Development Project (SUAMDP) was developed to formulate and utilize efficient and comprehensive methods for determining sensitivities of calculated results with respect to changes in all input parameters. The computerized methodology was embodied in the Gradient Enhanced Software System (GRESS). Due to the fact that GRESS was to be used in the site characterization for waste storage, stringent NQA-1 requirements were imposed by the sponsor. A working relationship between the Oak Ridge National Laboratory (ORNL) Quality Department and the research scientists developing GRESS was essential in achieving understanding and acceptance of the quality assurance requirements as applied to the SUAMDP. The relationship resulted in the SUAMDP becoming the first software project at ORNL to develop a comprehensive NQA-1 Quality Assurance Plan; this plan now serves as a model for software quality assurance at ORNL. This paper describes the evolution of this plan and its impact on the application of quality assurance procedures to software

Guidance and Control Software Project Data - Volume 2: Development Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the development documents from the GCS project. Volume 2 contains three appendices: A. Guidance and Control Software Development Specification; B. Design Description for the Pluto Implementation of the Guidance and Control Software; and C. Source Code for the Pluto Implementation of the Guidance and Control Software

SU-E-T-465: Implementation of An Automated Collision Detection Program Using Open Source Software for the Pinnacle Treatment Planning System

Energy Technology Data Exchange (ETDEWEB)

Tanny, S; Bogue, J; Parsai, E; Sperling, N [University of Toledo Medical Center, Toledo, OH (United States)

2015-06-15

Purpose: Potential collisions between the gantry head and the patient or table assembly are difficult to detect in most treatment planning systems. We have developed and implemented a novel software package for the representation of potential gantry collisions with the couch assembly at the time of treatment planning. Methods: Physical dimensions of the Varian Edge linear accelerator treatment head were measured and reproduced using the Visual Python display package. A script was developed for the Pinnacle treatment planning system to generate a file with the relevant couch, gantry, and isocenter positions for each beam in a planning trial. A python program was developed to parse the information from the TPS and produce a representative model of the couch/gantry system. Using the model and the Visual Python libraries, a rendering window is generated for each beam that allows the planner to evaluate the possibility of a collision. Results: Comparison against heuristic methods and direct verification on the machine validated the collision model generated by the software. Encounters of <1 cm between the gantry treatment head and table were visualized as collisions in our virtual model. Visual windows were created depicting the angle of collision for each beam, including the anticipated table coordinates. Visual rendering of a 6 arc trial with multiple couch positions was completed in under 1 minute, with network bandwidth being the primary bottleneck. Conclusion: The developed software allows for quick examination of possible collisions during the treatment planning process and helps to prevent major collisions prior to plan approval. The software can easily be implemented on future planning systems due to the versatility and platform independence of the Python programming language. Further integration of the software with the treatment planning system will allow the possibility of patient-gantry collision detection for a range of treatment machines.

SU-E-T-465: Implementation of An Automated Collision Detection Program Using Open Source Software for the Pinnacle Treatment Planning System

International Nuclear Information System (INIS)

Tanny, S; Bogue, J; Parsai, E; Sperling, N

2015-01-01

Purpose: Potential collisions between the gantry head and the patient or table assembly are difficult to detect in most treatment planning systems. We have developed and implemented a novel software package for the representation of potential gantry collisions with the couch assembly at the time of treatment planning. Methods: Physical dimensions of the Varian Edge linear accelerator treatment head were measured and reproduced using the Visual Python display package. A script was developed for the Pinnacle treatment planning system to generate a file with the relevant couch, gantry, and isocenter positions for each beam in a planning trial. A python program was developed to parse the information from the TPS and produce a representative model of the couch/gantry system. Using the model and the Visual Python libraries, a rendering window is generated for each beam that allows the planner to evaluate the possibility of a collision. Results: Comparison against heuristic methods and direct verification on the machine validated the collision model generated by the software. Encounters of <1 cm between the gantry treatment head and table were visualized as collisions in our virtual model. Visual windows were created depicting the angle of collision for each beam, including the anticipated table coordinates. Visual rendering of a 6 arc trial with multiple couch positions was completed in under 1 minute, with network bandwidth being the primary bottleneck. Conclusion: The developed software allows for quick examination of possible collisions during the treatment planning process and helps to prevent major collisions prior to plan approval. The software can easily be implemented on future planning systems due to the versatility and platform independence of the Python programming language. Further integration of the software with the treatment planning system will allow the possibility of patient-gantry collision detection for a range of treatment machines

A pioneering application of NQA-1 quality assurance standards in the development of software

International Nuclear Information System (INIS)

Weisbin, A.N.

1988-01-01

One reason for systematically applying quality assurance to computer software is the extensive use of results from computer programs to characterize potential sited for nuclear waste repositories leading ultimately to important policy making decisions. Because data from these programs characterize the likely radioactivity profile for many hundreds of years, experimental validation is not feasible. The Sensitivity and Uncertainty Analysis Methods Development Project (SUAMDP) was developed to formulate and utilize efficient and comprehensive methods for determining sensitivities of calculated results with respect to changes in all input parameters. The computerized methodology was embodied in the Gradient Enhanced Software System (GRESS). Due to the fact that GRESS was to be used in the site characterization for waste storage, stringent NQA-1 requirements were imposed by the sponsor. A working relationship between the Oak Ridge National Laboratory (ORNL) Quality Department and the research scientists developing GRESS was essential in achieving understanding and acceptance of the quality assurance requirements as applied to the SUAMDP. The relationship resulted in the SUAMDP becoming the first software project at ORNL to develop a comprehensive NQA-1 Quality Assurance Plan; this plan now serves as a model for software quality assurance at ORNL. This paper describes the evolution of this plan and its impact on the application of quality assurance procedures to software. 2 refs

Development of a transportation planning tool

International Nuclear Information System (INIS)

Funkhouser, B.R.; Moyer, J.W.; Ballweg, E.L.

1994-01-01

This paper describes the application of simulation modeling and logistics techniques to the development of a planning tool for the Department of Energy (DOE). The focus of the Transportation Planning Model (TPM) tool is to aid DOE and Sandia analysts in the planning of future fleet sizes, driver and support personnel sizes, base site locations, and resource balancing among the base sites. The design approach is to develop a rapid modeling environment which will allow analysts to easily set up a shipment scenario and perform multiple ''what if'' evaluations. The TPM is being developed on personal computers using commercial off-the shelf (COTS) software tools under the WINDOWS reg-sign operating environment. Prototype development of the TPM has been completed

Avionics Simulation, Development and Software Engineering

Science.gov (United States)

2002-01-01

During this reporting period, all technical responsibilities were accomplished as planned. A close working relationship was maintained with personnel of the MSFC Avionics Department Software Group (ED14), the MSFC EXPRESS Project Office (FD31), and the Huntsville Boeing Company. Accomplishments included: performing special tasks; supporting Software Review Board (SRB), Avionics Test Bed (ATB), and EXPRESS Software Control Panel (ESCP) activities; participating in technical meetings; and coordinating issues between the Boeing Company and the MSFC Project Office.

Crowdsourcing cloud-based software development

CERN Document Server

Li, Wei; Tsai, Wei-Tek; Wu, Wenjun

2015-01-01

This book presents the latest research on the software crowdsourcing approach to develop large and complex software in a cloud-based platform. It develops the fundamental principles, management organization and processes, and a cloud-based infrastructure to support this new software development approach. The book examines a variety of issues in software crowdsourcing processes, including software quality, costs, diversity of solutions, and the competitive nature of crowdsourcing processes. Furthermore, the book outlines a research roadmap of this emerging field, including all the key technology and management issues for the foreseeable future. Crowdsourcing, as demonstrated by Wikipedia and Facebook for online web applications, has shown promising results for a variety of applications, including healthcare, business, gold mining exploration, education, and software development. Software crowdsourcing is emerging as a promising solution to designing, developing and maintaining software. Preliminary software cr...

A REVIEW OF ESTIMATION OF SOFTWARE PRODUCTS DEVELOPMENT COSTS

Directory of Open Access Journals (Sweden)

Edin Osmanbegović

2017-01-01

Full Text Available In the modern business and management of business processes, the standardization of procedures allows the creation of added value, increasing competitiveness and success in the business of an organization. Evaluation of the budget for software development is crucial to the success of an IT project, because the inability to make a realistic assessment leads to inadequate project plans, customer dissatisfaction, poor quality of software products, and reduced profits. In order to minimize such situations, making accurate and reliable software cost estimation should be carried out at all stages of the project life cycle. Although hundreds of research articles focusing on the application of different methods of budget estimates of the software product have been published so far, there is no comprehensive review of the current situation or review of research trends in the budget estimates of the software product. This paper aims to create a framework for estimation of costs of development of software products by providing an overview of the most influential researchers, the most influential articles published in the WoS database, the most used keywords for searching the articles, as well as a review of the estimation techniques used in budget estimates of the software product.

Process development work plan for waste feed delivery system

International Nuclear Information System (INIS)

Papp, I.G.

1998-01-01

This work plan defines the process used to develop project definition for Waste Feed Delivery (WFD). Project definition provides the direction for development of definitive design media required for the ultimate implementation of operational processing hardware and software. Outlines for the major deliverables are attached as appendices. The implementation of hardware and software will accommodate requirements for safe retrieval and delivery of waste currently stored in Hanford's underground storage tanks. Operations and maintenance ensure the availability of systems, structures, and components for current and future planned operations within the boundary of the Tank Waste Remediation System (TWRS) authorization basis

Intelligent Tools for Planning Knowledge base Development and Verification

Science.gov (United States)

Chien, Steve A.

1996-01-01

A key obstacle hampering fielding of AI planning applications is the considerable expense of developing, verifying, updating, and maintaining the planning knowledge base (KB). Planning systems must be able to compare favorably in terms of software lifecycle costs to other means of automation such as scripts or rule-based expert systems.

Why and how Mastering an Incremental and Iterative Software Development Process

Science.gov (United States)

Dubuc, François; Guichoux, Bernard; Cormery, Patrick; Mescam, Jean Christophe

2004-06-01

One of the key issues regularly mentioned in the current software crisis of the space domain is related to the software development process that must be performed while the system definition is not yet frozen. This is especially true for complex systems like launchers or space vehicles.Several more or less mature solutions are under study by EADS SPACE Transportation and are going to be presented in this paper. The basic principle is to develop the software through an iterative and incremental process instead of the classical waterfall approach, with the following advantages:- It permits systematic management and incorporation of requirements changes over the development cycle with a minimal cost. As far as possible the most dimensioning requirements are analyzed and developed in priority for validating very early the architecture concept without the details.- A software prototype is very quickly available. It improves the communication between system and software teams, as it enables to check very early and efficiently the common understanding of the system requirements.- It allows the software team to complete a whole development cycle very early, and thus to become quickly familiar with the software development environment (methodology, technology, tools...). This is particularly important when the team is new, or when the environment has changed since the previous development. Anyhow, it improves a lot the learning curve of the software team.These advantages seem very attractive, but mastering efficiently an iterative development process is not so easy and induces a lot of difficulties such as:- How to freeze one configuration of the system definition as a development baseline, while most of thesystem requirements are completely and naturally unstable?- How to distinguish stable/unstable and dimensioning/standard requirements?- How to plan the development of each increment?- How to link classical waterfall development milestones with an iterative approach: when

NEAMS Software Licensing, Release, and Distribution: Implications for FY2013 Work Package Planning

International Nuclear Information System (INIS)

Bernholdt, David E.

2012-01-01

The vision of the NEAMS program is to bring truly predictive modeling and simulation (M and S) capabilities to the nuclear engineering community in order to enable a new approach to the analysis of nuclear systems. NEAMS anticipates issuing in FY 2018 a full release of its computational 'Fermi Toolkit' aimed at advanced reactor and fuel cycles. The NEAMS toolkit involves extensive software development activities, some of which have already been underway for several years, however, the Advanced Modeling and Simulation Office (AMSO), which sponsors the NEAMS program, has not yet issued any official guidance regarding software licensing, release, and distribution policies. This motivated an FY12 task in the Capability Transfer work package to develop and recommend an appropriate set of policies. The current preliminary report is intended to provide awareness of issues with implications for work package planning for FY13. We anticipate a small amount of effort associated with putting into place formal licenses and contributor agreements for NEAMS software which doesn't already have them. We do not anticipate any additional effort or costs associated with software release procedures or schedules beyond those dictated by the quality expectations for the software. The largest potential costs we anticipate would be associated with the setup and maintenance of shared code repositories for development and early access to NEAMS software products. We also anticipate an opportunity, with modest associated costs, to work with the Radiation Safety Information Computational Center (RSICC) to clarify export control assessment policies for software under development.

Development of Software for Measurement and Analysis of Solar Radiation

International Nuclear Information System (INIS)

Mohamad Idris Taib; Abul Adli Anuar; Noor Ezati Shuib

2015-01-01

This software was under development using LabVIEW to be using with StellarNet spectrometers system with USB communication to computer. LabVIEW have capabilities in hardware interfacing, graphical user interfacing and mathematical calculation including array manipulation and processing. This software read data from StellarNet spectrometer in real-time and then processed for analysis. Several measurement of solar radiation and analysis have been done. Solar radiation involved mainly infra-red, visible light and ultra-violet. With solar radiation spectrum data, information of weather and suitability of plant can be gathered and analyzed. Furthermore, optimization of utilization and safety precaution of solar radiation can be planned. Using this software, more research and development in utilization and safety of solar radiation can be explored. (author)

Lessons learned from development and quality assurance of software systems at the Halden Project

International Nuclear Information System (INIS)

Bjorlo, T.J.; Berg, O.; Pehrsen, M.; Dahll, G.; Sivertsen, T.

1996-01-01

The OECD Halden Reactor Project has developed a number of software systems within the research programmes. These programmes have comprised a wide range of topics, like studies of software for safety-critical applications, development of different operator support systems, and software systems for building and implementing graphical user interfaces. The systems have ranged from simple prototypes to installations in process plants. In the development of these software systems, Halden has gained much experience in quality assurance of different types of software. This paper summarises the accumulated experience at the Halden Project in quality assurance of software systems. The different software systems being developed at the Halden Project may be grouped into three categories. These are plant-specific software systems (one-of-a-kind deliveries), generic software products, and safety-critical software systems. This classification has been found convenient as the categories have different requirements to the quality assurance process. In addition, the experience from use of software development tools and proprietary software systems at Halden, is addressed. The paper also focuses on the experience gained from the complete software life cycle, starting with the software planning phase and ending with software operation and maintenance

Problems in software development for nuclear robotics

International Nuclear Information System (INIS)

Shinohara, Yoshikuni

1986-01-01

Major technical problems in developing softwares for intelligent robots for future nuclear applications are explained briefly. In order that a robot can perform various kinds of complex works, it must be equipped with a high level of artificial intelligence which includes sensing functions such as visiual, auditory, tactile, proximity sensing, cognitive functions such as recognition of objects and understanding of working environment, decision-making functions such as work planning and control functions such as manipulator and locomotion controls. A large amount of various kinds of signals and informations must be processed with a high speed for an integrated control of these functions. It will be desirable that the computer program for controlling a robot which must run in a real-time will have a functionally hierarchical and distributed structure from the view point of software development. Parallel processing will be required from the view point of computation time. (author)

75 FR 27341 - Increasing Market and Planning Efficiency Through Improved Software; Notice of Technical...

Science.gov (United States)

2010-05-14

..., ramp rates, and network topology), flexible dispatch, settlement calculations, transmission switching... Market and Planning Efficiency Through Improved Software; Notice of Technical Conference To Discuss Increasing Market and Planning Efficiency Through Improved Software May 7, 2010. Take notice that Commission...

Software quality assurance - seven years experience

International Nuclear Information System (INIS)

Malsbury, J.A.

1987-01-01

This paper describes seven years experience with software quality assurance at PPPL. It covers the early attempts of 1980 and 1981 to establish software quality assurance; the first attempt of 1982 to develop a complete software quality assurance plan; the significant modifications of this plan in 1985; and the future. In addition, the paper describes the role of the Quality Assurance organization within each plan. The scope of this paper is limited to discussions of the software development procedures used in the seven year period. Other software quality topics, such as configuration control or problem identification and resolution, are not discussed

Sandia National Laboratories Advanced Simulation and Computing (ASC) software quality plan part 2 mappings for the ASC software quality engineering practices, version 2.0.

Energy Technology Data Exchange (ETDEWEB)

Heaphy, Robert; Sturtevant, Judith E.; Hodges, Ann Louise; Boucheron, Edward A.; Drake, Richard Roy; Minana, Molly A.; Hackney, Patricia; Forsythe, Christi A.; Schofield, Joseph Richard, Jr. (,; .); Pavlakos, Constantine James; Williamson, Charles Michael; Edwards, Harold Carter

2006-09-01

The purpose of the Sandia National Laboratories Advanced Simulation and Computing (ASC) Software Quality Plan is to clearly identify the practices that are the basis for continually improving the quality of ASC software products. The plan defines the ASC program software quality practices and provides mappings of these practices to Sandia Corporate Requirements CPR001.3.2 and CPR001.3.6 and to a Department of Energy document, ''ASCI Software Quality Engineering: Goals, Principles, and Guidelines''. This document also identifies ASC management and software project teams' responsibilities in implementing the software quality practices and in assessing progress towards achieving their software quality goals.

Saltwell PIC Skid Programmable Logic Controller (PLC) Software Configuration Management Plan

International Nuclear Information System (INIS)

KOCH, M.R.

1999-01-01

This document provides the procedures and guidelines necessary for computer software configuration management activities during the operation and maintenance phases of the Saltwell PIC Skids as required by LMH-PRO-309/Rev. 0, Computer Software Quality Assurance, Section 2.6, Software Configuration Management. The software configuration management plan (SCMP) integrates technical and administrative controls to establish and maintain technical consistency among requirements, physical configuration, and documentation for the Saltwell PIC Skid Programmable Logic Controller (PLC) software during the Hanford application, operations and maintenance. This SCMP establishes the Saltwell PIC Skid PLC Software Baseline, status changes to that baseline, and ensures that software meets design and operational requirements and is tested in accordance with their design basis

Evidence-based development of a diagnosis-dependent therapy planning system and its implementation in modern diagnostic software.

Science.gov (United States)

Ahlers, M O; Jakstat, H A

2005-07-01

The prerequisite for structured individual therapy of craniomandibular dysfunctions is differential diagnostics. Suggestions for the structured recording of findings and their structured evaluation beyond the global diagnosis of "craniomandibular disorders" have been published. Only this structured approach enables computerization of the diagnostic process. The respective software is available for use in practice (CMDcheck for CMD screening, CMDfact for the differential diagnostics). Based on this structured diagnostics, knowledge-based therapy planning is also conceivable. The prerequisite for this would be a model of achieving consensus on the indicated forms of therapy related to the diagnosis. Therefore, a procedure for evidence-based achievement of consensus on suitable forms of therapy in CMD was developed first in multicentric cooperation, and then implemented in corresponding software. The clinical knowledge of experienced specialists was included consciously for the consensus achievement process. At the same time, anonymized mathematical statistical evaluations were used for control and objectification. Different examiners form different departments of several universities working independently of one another assigned the theoretically conceiveable therapeutic alternatives to the already published diagnostic scheme. After anonymization, the correlation of these assignments was then calculated mathematically. For achieving consensus in those cases for which no agreement initally existed, agreement was subsequently arrived at in the course of a consensus conference on the basis of literature evaluations and the discussion of clinical case examples. This consensus in turn finally served as the basis of a therapy planner implemented in the above-mentioned diagnostic software CMDfact. Contributing to quality assurance, the principles of programming this assistant as well as the interface for linking into the diagnostic software are documented and also published

Computer-Aided Software Engineering - An approach to real-time software development

Science.gov (United States)

Walker, Carrie K.; Turkovich, John J.

1989-01-01

A new software engineering discipline is Computer-Aided Software Engineering (CASE), a technology aimed at automating the software development process. This paper explores the development of CASE technology, particularly in the area of real-time/scientific/engineering software, and a history of CASE is given. The proposed software development environment for the Advanced Launch System (ALS CASE) is described as an example of an advanced software development system for real-time/scientific/engineering (RT/SE) software. The Automated Programming Subsystem of ALS CASE automatically generates executable code and corresponding documentation from a suitably formatted specification of the software requirements. Software requirements are interactively specified in the form of engineering block diagrams. Several demonstrations of the Automated Programming Subsystem are discussed.

Developing free software for automatic registration for the quality control of IMRT with movies

International Nuclear Information System (INIS)

Moral, F. del; Meilan, E.; Pereira, L.; Salvador, F.; Munoz, V.; Salgado, M.

2011-01-01

In this work, as the commissioner of the e-JMRT, a Monte Carlo calculation network for IMRT planning, has developed software for the automatic recording of the image of the film with the results of the planning system.

NASA software documentation standard software engineering program

Science.gov (United States)

1991-01-01

The NASA Software Documentation Standard (hereinafter referred to as Standard) can be applied to the documentation of all NASA software. This Standard is limited to documentation format and content requirements. It does not mandate specific management, engineering, or assurance standards or techniques. This Standard defines the format and content of documentation for software acquisition, development, and sustaining engineering. Format requirements address where information shall be recorded and content requirements address what information shall be recorded. This Standard provides a framework to allow consistency of documentation across NASA and visibility into the completeness of project documentation. This basic framework consists of four major sections (or volumes). The Management Plan contains all planning and business aspects of a software project, including engineering and assurance planning. The Product Specification contains all technical engineering information, including software requirements and design. The Assurance and Test Procedures contains all technical assurance information, including Test, Quality Assurance (QA), and Verification and Validation (V&V). The Management, Engineering, and Assurance Reports is the library and/or listing of all project reports.

Firing Room Remote Application Software Development & Swamp Works Laboratory Robot Software Development

Science.gov (United States)

Garcia, Janette

2016-01-01

The National Aeronautics and Space Administration (NASA) is creating a way to send humans beyond low Earth orbit, and later to Mars. Kennedy Space Center (KSC) is working to make this possible by developing a Spaceport Command and Control System (SCCS) which will allow the launch of Space Launch System (SLS). This paper's focus is on the work performed by the author in her first and second part of the internship as a remote application software developer. During the first part of her internship, the author worked on the SCCS's software application layer by assisting multiple ground subsystems teams including Launch Accessories (LACC) and Environmental Control System (ECS) on the design, development, integration, and testing of remote control software applications. Then, on the second part of the internship, the author worked on the development of robot software at the Swamp Works Laboratory which is a research and technology development group which focuses on inventing new technology to help future In-Situ Resource Utilization (ISRU) missions.

The Liquid Argon Software Toolkit (LArSoft): Goals, Status and Plan

Energy Technology Data Exchange (ETDEWEB)

Pordes, Rush [Fermilab; Snider, Erica [Fermilab

2016-08-17

LArSoft is a toolkit that provides a software infrastructure and algorithms for the simulation, reconstruction and analysis of events in Liquid Argon Time Projection Chambers (LArTPCs). It is used by the ArgoNeuT, LArIAT, MicroBooNE, DUNE (including 35ton prototype and ProtoDUNE) and SBND experiments. The LArSoft collaboration provides an environment for the development, use, and sharing of code across experiments. The ultimate goal is to develop fully automatic processes for reconstruction and analysis of LArTPC events. The toolkit is based on the art framework and has a well-defined architecture to interface to other packages, including to GEANT4 and GENIE simulation software and the Pandora software development kit for pattern recognition. It is designed to facilitate and support the evolution of algorithms including their transition to new computing platforms. The development of the toolkit is driven by the scientific stakeholders involved. The core infrastructure includes standard definitions of types and constants, means to input experiment geometries as well as meta and event- data in several formats, and relevant general utilities. Examples of algorithms experiments have contributed to date are: photon-propagation; particle identification; hit finding, track finding and fitting; electromagnetic shower identification and reconstruction. We report on the status of the toolkit and plans for future work.

Secure software development training course

Directory of Open Access Journals (Sweden)

Victor S. Gorbatov

2017-06-01

Full Text Available Information security is one of the most important criteria for the quality of developed software. To obtain a sufficient level of application security companies implement security process into software development life cycle. At this stage software companies encounter with deficit employees who able to solve problems of software design, implementation and application security. This article provides a description of the secure software development training course. Training course of application security is designed for co-education students of different IT-specializations.

Factors that motivate software developers in Nigerian's software ...

African Journals Online (AJOL)

It was also observed those courtesy, good reward systems, regular training, recognition, tolerance of mistakes and good leadership were high motivators of software developers. Keywords: Software developers, information technology, project managers, Nigeria International Journal of Natural and Applied Sciences, 6(4): ...

Comparative study on software development methodologies

Directory of Open Access Journals (Sweden)

Mihai Liviu DESPA

2014-12-01

Full Text Available This paper focuses on the current state of knowledge in the field of software development methodologies. It aims to set the stage for the formalization of a software development methodology dedicated to innovation orientated IT projects. The paper starts by depicting specific characteristics in software development project management. Managing software development projects involves techniques and skills that are proprietary to the IT industry. Also the software development project manager handles challenges and risks that are predominantly encountered in business and research areas that involve state of the art technology. Conventional software development stages are defined and briefly described. Development stages are the building blocks of any software development methodology so it is important to properly research this aspect. Current software development methodologies are presented. Development stages are defined for every showcased methodology. For each methodology a graphic representation is illustrated in order to better individualize its structure. Software development methodologies are compared by highlighting strengths and weaknesses from the stakeholder's point of view. Conclusions are formulated and a research direction aimed at formalizing a software development methodology dedicated to innovation orientated IT projects is enunciated.

Usability in open source software development

DEFF Research Database (Denmark)

Andreasen, M. S.; Nielsen, H. V.; Schrøder, S. O.

2006-01-01

Open Source Software (OSS) development has gained significant importance in the production of soft-ware products. Open Source Software developers have produced systems with a functionality that is competitive with similar proprietary software developed by commercial software organizations. Yet OSS...

The Ragnarok Software Development Environment

DEFF Research Database (Denmark)

Christensen, Henrik Bærbak

1999-01-01

Ragnarok is an experimental software development environment that focuses on enhanced support for managerial activities in large scale software development taking the daily work of the software developer as its point of departure. The main emphasis is support in three areas: management, navigation......, and collaboration. The leitmotif is the software architecture, which is extended to handle managerial data in addition to source code; this extended software architecture is put under tight version- and configuration management control and furthermore used as basis for visualisation. Preliminary results of using...

Dosimetric verification of a software for planning of radio therapeutical treatments

International Nuclear Information System (INIS)

Alfonso, R.; Huerta, U.; Alfonso, J.L.; Torres, M.

1995-01-01

A software for radiation treatment planning was recently developed by medical physicists at the Hermanos Ameijeiras Hospital in Havana. Selected locations in head and neck region were used to evaluate the reliability of calculated dose distributions in patients, taking as a reference the results of dosimetric measurements with TLD-700 powder in a RANDO type phantom. The different options is shown. Causes of discrepancies are analyzed and recommendations are made for the use of data acquisitions options

Customer Interaction in Software Development: A Comparison of Software Methodologies Deployed in Namibian Software Firms

CSIR Research Space (South Africa)

Iyawa, GE

2016-01-01

Full Text Available within the Namibian context. An implication for software project managers and software developers is that customer interaction should be properly managed to ensure that the software methodologies for improving software development processes...

On the Use of Hybrid Development Approaches in Software and Systems Development

DEFF Research Database (Denmark)

Kuhrmann, Marco; Münch, Jürgen; Diebold, Philipp

2016-01-01

A software process is the game plan to organize project teams and run projects. Yet, it still is a challenge to select the appropriate development approach for the respective context. A multitude of development approaches compete for the users’ favor, but there is no silver bullet serving all...... possible setups. Moreover, recent research as well as experience from practice shows companies utilizing different development approaches to assemble the best-fitting approach for the respective company: a more traditional process provides the basic framework to serve the organization, while project teams...

Visual Sample Plan (VSP) Software: Designs and Data Analyses for Sampling Contaminated Buildings

International Nuclear Information System (INIS)

Pulsipher, Brent A.; Wilson, John E.; Gilbert, Richard O.; Nuffer, Lisa L.; Hassig, Nancy L.

2005-01-01

A new module of the Visual Sample Plan (VSP) software has been developed to provide sampling designs and data analyses for potentially contaminated buildings. An important application is assessing levels of contamination in buildings after a terrorist attack. This new module, funded by DHS through the Combating Terrorism Technology Support Office, Technical Support Working Group, was developed to provide a tailored, user-friendly and visually-orientated buildings module within the existing VSP software toolkit, the latest version of which can be downloaded from http://dqo.pnl.gov/vsp. In case of, or when planning against, a chemical, biological, or radionuclide release within a building, the VSP module can be used to quickly and easily develop and visualize technically defensible sampling schemes for walls, floors, ceilings, and other surfaces to statistically determine if contamination is present, its magnitude and extent throughout the building and if decontamination has been effective. This paper demonstrates the features of this new VSP buildings module, which include: the ability to import building floor plans or to easily draw, manipulate, and view rooms in several ways; being able to insert doors, windows and annotations into a room; 3-D graphic room views with surfaces labeled and floor plans that show building zones that have separate air handing units. The paper will also discuss the statistical design and data analysis options available in the buildings module. Design objectives supported include comparing an average to a threshold when the data distribution is normal or unknown, and comparing measurements to a threshold to detect hotspots or to insure most of the area is uncontaminated when the data distribution is normal or unknown

Comparative study on software development methodologies

OpenAIRE

Mihai Liviu DESPA

2014-01-01

This paper focuses on the current state of knowledge in the field of software development methodologies. It aims to set the stage for the formalization of a software development methodology dedicated to innovation orientated IT projects. The paper starts by depicting specific characteristics in software development project management. Managing software development projects involves techniques and skills that are proprietary to the IT industry. Also the software development project manager han...

Global software development

DEFF Research Database (Denmark)

Matthiesen, Stina

2016-01-01

This overview presents the mid stages of my doctoral research-based on ethnographic work conducted in IT companies in India and in Denmark-on collaborative work within global software development (GSD). In the following I briefly introduce how this research seeks to spark a debate in CSCW...... by challenging contemporary ideals about software development outsourcing through the exploration of the multiplicities and asymmetric dynamics inherent in the collaborative work of GSD....

Impact of Agile Software Development Model on Software Maintainability

Science.gov (United States)

Gawali, Ajay R.

2012-01-01

Software maintenance and support costs account for up to 60% of the overall software life cycle cost and often burdens tightly budgeted information technology (IT) organizations. Agile software development approach delivers business value early, but implications on software maintainability are still unknown. The purpose of this quantitative study…

MEASUREMENT PROCESS OF SOFTWARE DEVELOPMENT PROJECTS FOR SUPPORTING STRATEGIC BUSINESS OBJECTIVES IN SOFTWARE DEVELOPING COMPANIES

Directory of Open Access Journals (Sweden)

Sandra Lais Pedroso

2013-08-01

Full Text Available Software developing companies work in a competitive market and are often challenged to make business decisions with impact on competitiveness. Models accessing maturity for software development processes quality, such as CMMI and MPS-BR, comprise process measurements systems (PMS. However, these models are not necessarily suitable to support business decisions, neither to achieve strategic goals. The objective of this work is to analyze how the PMS of software development projects could support business strategies for software developing companies. Results taken from this work show that PMS results from maturity models for software processes can be suited to help evaluating operating capabilities and supporting strategic business decisions.

Aspect-Oriented Software Development

NARCIS (Netherlands)

Filman, R.E.; Elrad, T.; Clarke, S.; Aksit, Mehmet; Unknown, [Unknown

2004-01-01

Software development is changing. The opportunities of the Internet, computerized businesses, and computer-savvy consumers, the exponential decline in the cost of computation and communication, and the increasingly dynamic environment for longer-living systems are pressing software developers to

SU-E-J-80: A Comparative Analysis of MIM and Pinnacle Software for Adaptive Planning

Energy Technology Data Exchange (ETDEWEB)

Stanford, J; Duggar, W; Morris, B; Yang, C [University of Mississippi Med. Center, Jackson, MS (United States)

2015-06-15

Purpose: IMRT treatment is often administered with image guidance and small PTV margins. Change in body habitus such as weight loss and tumor response during the course of a treatment could be significant, thus warranting re-simulation and re-planning. Adaptive planning is challenging and places significant burden on the staff, as such some commercial vendors are now offering adaptive planning software to stream line the process of re-planning and dose accumulation between different CT data set. The purpose of this abstract is to compare the adaptive planning tools between Pinnacle version 9.8 and MIM 6.4 software. Methods: Head and Neck cases of previously treated patients that experienced anatomical changes during the course of their treatment were chosen for evaluation. The new CT data set from the re-simulation was imported to Pinnacle and MIM software. The dynamic planning tool in pinnacle was used to calculate the old plan with fixed MU setting on the new CT data. In MIM, the old CT was registered to the new data set, followed by a dose transformation to the new CT. The dose distribution to the PTV and critical structures from each software were analyzed and compared. Results: 9% difference was observed between the Global maximum doses reported by both software. Mean doses to organs at risk and PTV’s were within 6 % however pinnacle showed greater difference in PTV coverage change. Conclusion: MIM software adaptive planning corrects for geometrical changes without consideration for the effect of radiological path length on dose distribution; however Pinnacle corrects for both geometric and radiological effect on the dose distribution. Pinnacle gives a better estimate of the dosimetric impact due to anatomical changes.

Agile software development

CERN Document Server

Stober, Thomas

2009-01-01

Software Development is moving towards a more agile and more flexible approach. It turns out that the traditional 'waterfall' model is not supportive in an environment where technical, financial and strategic constraints are changing almost every day. But what is agility? What are today's major approaches? And especially: What is the impact of agile development principles on the development teams, on project management and on software architects? How can large enterprises become more agile and improve their business processes, which have been existing since many, many years? What are the limit

Decision support software technology demonstration plan

Energy Technology Data Exchange (ETDEWEB)

SULLIVAN,T.; ARMSTRONG,A.

1998-09-01

The performance evaluation of innovative and alternative environmental technologies is an integral part of the US Environmental Protection Agency's (EPA) mission. Early efforts focused on evaluating technologies that supported the implementation of the Clean Air and Clean Water Acts. In 1986 the Agency began to demonstrate and evaluate the cost and performance of remediation and monitoring technologies under the Superfund Innovative Technology Evaluation (SITE) program (in response to the mandate in the Superfund Amendments and Reauthorization Act of 1986 (SARA)). In 1990, the US Technology Policy was announced. This policy placed a renewed emphasis on making the best use of technology in achieving the national goals of improved quality of life for all Americans, continued economic growth, and national security. In the spirit of the technology policy, the Agency began to direct a portion of its resources toward the promotion, recognition, acceptance, and use of US-developed innovative environmental technologies both domestically and abroad. Decision Support Software (DSS) packages integrate environmental data and simulation models into a framework for making site characterization, monitoring, and cleanup decisions. To limit the scope which will be addressed in this demonstration, three endpoints have been selected for evaluation: Visualization; Sample Optimization; and Cost/Benefit Analysis. Five topics are covered in this report: the objectives of the demonstration; the elements of the demonstration plan; an overview of the Site Characterization and Monitoring Technology Pilot; an overview of the technology verification process; and the purpose of this demonstration plan.

Windows Calorimeter Control (WinCal) program computer software configuration management plan

International Nuclear Information System (INIS)

1997-01-01

This document describes the system configuration management activities performed in support of the Windows Calorimeter Control (WinCal) system, in accordance with Site procedures based on Institute of Electrical and Electronic Engineers (IEEE) Standard 828-1990, Standard for Software Configuration Management Plans (IEEE 1990) and IEEE Standard 1042-1987, Guide to Software Configuration Management (IEEE 1987)

Planning and Analysis of the Company’s Financial Performances by Using a Software Simulation

Directory of Open Access Journals (Sweden)

Meri BOSHKOSKA

2017-06-01

Full Text Available Information Technology includes a wide range of software solution that helps managers in decision making processes in order to increase the company's business performance. Using software solution in financial analysis is a valuable tool for managers in the financial decision making process. The objective of the study was accomplished by developing Software that easily determines the financial performances of the company through integration of the analysis of financial indicators and DuPont profitability analysis model. Through this software, managers will be able to calculate the current financial state and visually analyze how their actions will affect the financial performance of the company. This will enable them to identify the best ways to improve the financial performance of the company. The software can perform a financial analysis and give a clear, useful overview of the current business performance and can also help in planning the growth of the company. The Software can also be implemented in educational purposes for students and managers in the field of financial management.

Software Engineering Improvement Plan

Science.gov (United States)

2006-01-01

In performance of this task order, bd Systems personnel provided support to the Flight Software Branch and the Software Working Group through multiple tasks related to software engineering improvement and to activities of the independent Technical Authority (iTA) Discipline Technical Warrant Holder (DTWH) for software engineering. To ensure that the products, comments, and recommendations complied with customer requirements and the statement of work, bd Systems personnel maintained close coordination with the customer. These personnel performed work in areas such as update of agency requirements and directives database, software effort estimation, software problem reports, a web-based process asset library, miscellaneous documentation review, software system requirements, issue tracking software survey, systems engineering NPR, and project-related reviews. This report contains a summary of the work performed and the accomplishments in each of these areas.

A Roadmap to Continuous Integration for ATLAS Software Development

Science.gov (United States)

Elmsheuser, J.; Krasznahorkay, A.; Obreshkov, E.; Undrus, A.; ATLAS Collaboration

2017-10-01

The ATLAS software infrastructure facilitates efforts of more than 1000 developers working on the code base of 2200 packages with 4 million lines of C++ and 1.4 million lines of python code. The ATLAS offline code management system is the powerful, flexible framework for processing new package versions requests, probing code changes in the Nightly Build System, migration to new platforms and compilers, deployment of production releases for worldwide access and supporting physicists with tools and interfaces for efficient software use. It maintains multi-stream, parallel development environment with about 70 multi-platform branches of nightly releases and provides vast opportunities for testing new packages, for verifying patches to existing software and for migrating to new platforms and compilers. The system evolution is currently aimed on the adoption of modern continuous integration (CI) practices focused on building nightly releases early and often, with rigorous unit and integration testing. This paper describes the CI incorporation program for the ATLAS software infrastructure. It brings modern open source tools such as Jenkins and GitLab into the ATLAS Nightly System, rationalizes hardware resource allocation and administrative operations, provides improved feedback and means to fix broken builds promptly for developers. Once adopted, ATLAS CI practices will improve and accelerate innovation cycles and result in increased confidence in new software deployments. The paper reports the status of Jenkins integration with the ATLAS Nightly System as well as short and long term plans for the incorporation of CI practices.

A Quantitative Study of Global Software Development Teams, Requirements, and Software Projects

Science.gov (United States)

Parker, Linda L.

2016-01-01

The study explored the relationship between global software development teams, effective software requirements, and stakeholders' perception of successful software development projects within the field of information technology management. It examined the critical relationship between Global Software Development (GSD) teams creating effective…

Software design practice using two SCADA software packages

DEFF Research Database (Denmark)

Basse, K.P.; Christensen, Georg Kronborg; Frederiksen, P. K.

1996-01-01

Typical software development for manufacturing control is done either by specialists with consideral real-time programming experience or done by the adaptation of standard software packages for manufacturing control. After investigation and test of two commercial software packages: "InTouch" and ......Touch" and "Fix", it is argued, that a more efficient software solution can be achieved by utilising an integrated specification for SCADA and PLC-programming. Experiences gained from process control is planned investigated for descrete parts manufacturing....

Open Source Software Development

Science.gov (United States)

2011-01-01

appropriate to refer to FOSS or FLOSS (L for Libre , where the alternative term “ libre software ” has popularity in some parts of the world) in order...Applying Social Network Analysis to Community-Drive Libre Software Projects, Intern. J. Info. Tech. and Web Engineering, 2006, 1(3), 27-28. 17...Open Source Software Development* Walt Scacchi Institute for Software Researcher University of California, Irvine Irvine, CA 92697-3455 USA Abstract

Software Development as Music Education Research

Science.gov (United States)

Brown, Andrew R.

2007-01-01

This paper discusses how software development can be used as a method for music education research. It explains how software development can externalize ideas, stimulate action and reflection, and provide evidence to support the educative value of new software-based experiences. Parallels between the interactive software development process and…

APPLICATION OF AHP METHOD FOR THE SELECTION OF BUSINESS PLAN SOFTWARE

Directory of Open Access Journals (Sweden)

Marko Hell

2013-02-01

Full Text Available This study seeks to determine the importance of tools that are offered within the software (simplicity, help, etc. and sort them according to your preferences. The results are intended for novice users in business planning. The study was carried out among students who are familiar with the possibilities of five programs for business planning. The students conducted the evaluation in accordance with each of the presented programs that were selected by experts from the problem areas. The practical importance of the results of this research is seen as a recommendation of faculties of economics in procurement of software for business planning for educational purposes. It is possible to apply the already appointed multi criteria (AHP model to the target group with extensive entrepreneurial experience, with a change to the set of criteria weights.

Formalizing the ISDF Software Development Methodology

OpenAIRE

Mihai Liviu DESPA

2015-01-01

The paper is aimed at depicting the ISDF software development methodology by emphasizing quality management and software development lifecycle. The ISDF methodology was built especially for innovative software development projects. The ISDF methodology was developed empirically by trial and error in the process of implementing multiple innovative projects. The research process began by analysing key concepts like innovation and software development and by settling the important dilemma of wha...

Teamwork in Distributed Agile Software Development

OpenAIRE

Gurram, Chaitanya; Bandi, Srinivas Goud

2013-01-01

Context: Distributed software development has become a most desired way of software development. Application of agile development methodologies in distributed environments has taken a new trend in developing software due to its benefits of improved communication and collaboration. Teamwork is an important concept that agile methodologies facilitate and is one of the potential determinants of team performance which was not focused in distributed agile software development. Objectives: This res...

Static and Completion Analysis for Planning Knowledge Base Development and Verification

Science.gov (United States)

Chien, Steve A.

1996-01-01

A key obstacle hampering fielding of AI planning applications is the considerable expense of developing, verifying, updating, and maintaining the planning knowledge base (KB). Planning systems must be able to compare favorably in terms of software lifecycle costs to other means of automation such as scripts or rule-based expert systems.

Gammasphere software development. Progress report

Energy Technology Data Exchange (ETDEWEB)

Piercey, R.B.

1994-01-01

This report describes the activities of the nuclear physics group at Mississippi State University which were performed during 1993. Significant progress has been made in the focus areas: chairing the Gammasphere Software Working Group (SWG); assisting with the porting and enhancement of the ORNL UPAK histogramming software package; and developing standard formats for Gammasphere data products. In addition, they have established a new public ftp archive to distribute software and software development tools and information.

Strategies for Developing China's Software Industry

Directory of Open Access Journals (Sweden)

Mingzhi Li

2003-01-01

Full Text Available The software industry is deemed an ideal target for a developing country to integrate into the world information and communications technology (ICT market. On the one hand the industry is labor intensive, and the developing countries have a large labor surplus; on the other hand, it is a worldwide trend for developed countries to outsource a vast amount of low-end, software-related tasks to the low-cost countries and regions, which fits into some developing countries’ caliber nicely. India has often been cited as the role model for a developing country to tap into the world software market for its continuous success in the software export sector. In comparison, China’s software industry is still negligible in the world despite its sustained high economic growth rate since the economic reform took off in the late 1970s.This paper aims at examining strategies for developing China’s software industry. We use India as a reference because of the similarities of the two countries’ stages of economic development and the clear divergence in their ICT structures and development paths. Although the language barrier has often been singled out as the major obstacle for China’s software exports, we believe the major reasons for its underdevelopment can be ascribed to the following factors. On the national level, the government attention has been skewed toward the hardware sector in the ICT industry, and there is no clear national vision for the strategic direction for the software industry.On the industry and ªrm level, software development has been regarded as the art of individual creativity rather than an engineering process. As a result, the importance of quality and standards, the two important critical factors in software development, have been largely neglected. Perhaps an even more fundamental factor lies in the deeply rooted notion that software is an attachment to the hardware and should be a free product. The lack of intellectual

Software configuration management plan for the Hanford site technical database

International Nuclear Information System (INIS)

GRAVES, N.J.

1999-01-01

The Hanford Site Technical Database (HSTD) is used as the repository/source for the technical requirements baseline and programmatic data input via the Hanford Site and major Hanford Project Systems Engineering (SE) activities. The Hanford Site SE effort has created an integrated technical baseline for the Hanford Site that supports SE processes at the Site and project levels which is captured in the HSTD. The HSTD has been implemented in Ascent Logic Corporation (ALC) Commercial Off-The-Shelf (COTS) package referred to as the Requirements Driven Design (RDD) software. This Software Configuration Management Plan (SCMP) provides a process and means to control and manage software upgrades to the HSTD system

Software Project Management

Science.gov (United States)

1989-07-01

incorporated into the sys- Kotler88 tem. Several interesting concepts are presented, but Kotler , P. Marketing Planning: Analysis, Planning, the bulk of the...the development organiza- In some environments, a software product is de- tion. veloped on speculation that there is a market for Teaching Consideration...development houses find it necessary to b. Types of plans know what the potential market for the product There are a number of plans developed in

Computer-aided software development

International Nuclear Information System (INIS)

Teichroew, D.; Hershey, E.A. III; Yamamoto, Y.

1978-01-01

In recent years, as the hardware cost/capability ratio has continued to decrease and as much of the routine data processing has been computerized, the emphasis in software development has shifted from just getting systems operational to the maintenance of existing systems, reduction of duplication by integration, selective addition of new applications, systems that are more usable, maintainable, portable and reliable and to improving the productivity of software developers. This paper examines a number of trends that are changing the methods by which software is being produced and used. (Auth.)

Extending the agile development process to develop acceptably secure software

NARCIS (Netherlands)

Ben Othmane, L.; Angin, P.; Weffers, H.T.G.; Bhargava, B.

2013-01-01

The agile software development approach makes developing secure software challenging. Existing approaches for extending the agile development process, which enables incremental and iterative software development, fall short of providing a method for efficiently ensuring the security of the software

Applying the metro map to software development management

Science.gov (United States)

Aguirregoitia, Amaia; Dolado, J. Javier; Presedo, Concepción

2010-01-01

This paper presents MetroMap, a new graphical representation model for controlling and managing the software development process. Metromap uses metaphors and visual representation techniques to explore several key indicators in order to support problem detection and resolution. The resulting visualization addresses diverse management tasks, such as tracking of deviations from the plan, analysis of patterns of failure detection and correction, overall assessment of change management policies, and estimation of product quality. The proposed visualization uses a metaphor with a metro map along with various interactive techniques to represent information concerning the software development process and to deal efficiently with multivariate visual queries. Finally, the paper shows the implementation of the tool in JavaFX with data of a real project and the results of testing the tool with the aforementioned data and users attempting several information retrieval tasks. The conclusion shows the results of analyzing user response time and efficiency using the MetroMap visualization system. The utility of the tool was positively evaluated.

Towards Archetypes-Based Software Development

Science.gov (United States)

Piho, Gunnar; Roost, Mart; Perkins, David; Tepandi, Jaak

We present a framework for the archetypes based engineering of domains, requirements and software (Archetypes-Based Software Development, ABD). An archetype is defined as a primordial object that occurs consistently and universally in business domains and in business software systems. An archetype pattern is a collaboration of archetypes. Archetypes and archetype patterns are used to capture conceptual information into domain specific models that are utilized by ABD. The focus of ABD is on software factories - family-based development artefacts (domain specific languages, patterns, frameworks, tools, micro processes, and others) that can be used to build the family members. We demonstrate the usage of ABD for developing laboratory information management system (LIMS) software for the Clinical and Biomedical Proteomics Group, at the Leeds Institute of Molecular Medicine, University of Leeds.

Software for Probabilistic Risk Reduction

Science.gov (United States)

Hensley, Scott; Michel, Thierry; Madsen, Soren; Chapin, Elaine; Rodriguez, Ernesto

2004-01-01

A computer program implements a methodology, denoted probabilistic risk reduction, that is intended to aid in planning the development of complex software and/or hardware systems. This methodology integrates two complementary prior methodologies: (1) that of probabilistic risk assessment and (2) a risk-based planning methodology, implemented in a prior computer program known as Defect Detection and Prevention (DDP), in which multiple requirements and the beneficial effects of risk-mitigation actions are taken into account. The present methodology and the software are able to accommodate both process knowledge (notably of the efficacy of development practices) and product knowledge (notably of the logical structure of a system, the development of which one seeks to plan). Estimates of the costs and benefits of a planned development can be derived. Functional and non-functional aspects of software can be taken into account, and trades made among them. It becomes possible to optimize the planning process in the sense that it becomes possible to select the best suite of process steps and design choices to maximize the expectation of success while remaining within budget.

MEASURING PRODUCTIVITY OF SOFTWARE DEVELOPMENT TEAMS

Directory of Open Access Journals (Sweden)

Goparaju Purna Sudhakar

2012-02-01

Full Text Available This paper gives an exhaustive literature review of the techniques and models available tomeasure the productivity of software development teams. Definition of productivity, measuringindividual programmer’s productivity, and measuring software development team productivity arediscussed. Based on the literature review it was found that software productivity measurement canbe done using SLOC (Source Lines of Code, function points, use case points, object points, andfeature points. Secondary research findings indicate that the team size, response time, taskcomplexity, team climate and team cohesion have an impact on software development teamproductivity. List of factors affecting the software development team productivity are studied andreviewed.

Lessons learned applying CASE methods/tools to Ada software development projects

Science.gov (United States)

Blumberg, Maurice H.; Randall, Richard L.

1993-01-01

This paper describes the lessons learned from introducing CASE methods/tools into organizations and applying them to actual Ada software development projects. This paper will be useful to any organization planning to introduce a software engineering environment (SEE) or evolving an existing one. It contains management level lessons learned, as well as lessons learned in using specific SEE tools/methods. The experiences presented are from Alpha Test projects established under the STARS (Software Technology for Adaptable and Reliable Systems) project. They reflect the front end efforts by those projects to understand the tools/methods, initial experiences in their introduction and use, and later experiences in the use of specific tools/methods and the introduction of new ones.

Knowledge-Based Software Management

International Nuclear Information System (INIS)

Sally Schaffner; Matthew Bickley; Brian Bevins; Leon Clancy; Karen White

2003-01-01

Management of software in a dynamic environment such as is found at Jefferson Lab can be a daunting task. Software development tasks are distributed over a wide range of people with varying skill levels. The machine configuration is constantly changing requiring upgrades to software at both the hardware control level and the operator control level. In order to obtain high quality support from vendor service agreements, which is vital to maintaining 24/7 operations, hardware and software must be kept at industry's current levels. This means that periodic upgrades independent of machine configuration changes must take place. It is often difficult to identify and organize the information needed to guide the process of development, upgrades and enhancements. Dependencies between support software and applications need to be consistently identified to prevent introducing errors during upgrades and to allow adequate testing to be planned and performed. Developers also need access to information regarding compilers, make files and organized distribution directories. This paper describes a system under development at Jefferson Lab which will provide software developers and managers this type of information in a timely user-friendly fashion. The current status and future plans for the system will be detailed

Insights into software development in Japan

Science.gov (United States)

Duvall, Lorraine M.

1992-01-01

The interdependence of the U.S.-Japanese economies makes it imperative that we in the United States understand how business and technology developments take place in Japan. We can gain insight into these developments in software engineering by studying the context in which Japanese software is developed, the practices that are used, the problems encountered, the setting surrounding these problems, and the resolution of these problems. Context includes the technological and sociological characteristics of the software development environment, the software processes applied, personnel involved in the development process, and the corporate and social culture surrounding the development. Presented in this paper is a summary of results of a study that addresses these issues. Data for this study was collected during a three month visit to Japan where the author interviewed 20 software managers representing nine companies involved in developing software in Japan. These data are compared to similar data from the United States in which 12 managers from five companies were interviewed.

Interactive reconstructions of cranial 3D implants under MeVisLab as an alternative to commercial planning software.

Directory of Open Access Journals (Sweden)

Jan Egger

Full Text Available In this publication, the interactive planning and reconstruction of cranial 3D Implants under the medical prototyping platform MeVisLab as alternative to commercial planning software is introduced. In doing so, a MeVisLab prototype consisting of a customized data-flow network and an own C++ module was set up. As a result, the Computer-Aided Design (CAD software prototype guides a user through the whole workflow to generate an implant. Therefore, the workflow begins with loading and mirroring the patients head for an initial curvature of the implant. Then, the user can perform an additional Laplacian smoothing, followed by a Delaunay triangulation. The result is an aesthetic looking and well-fitting 3D implant, which can be stored in a CAD file format, e.g. STereoLithography (STL, for 3D printing. The 3D printed implant can finally be used for an in-depth pre-surgical evaluation or even as a real implant for the patient. In a nutshell, our research and development shows that a customized MeVisLab software prototype can be used as an alternative to complex commercial planning software, which may also not be available in every clinic. Finally, not to conform ourselves directly to available commercial software and look for other options that might improve the workflow.

Interactive reconstructions of cranial 3D implants under MeVisLab as an alternative to commercial planning software

Science.gov (United States)

Egger, Jan; Gall, Markus; Tax, Alois; Ücal, Muammer; Zefferer, Ulrike; Li, Xing; von Campe, Gord; Schäfer, Ute; Schmalstieg, Dieter; Chen, Xiaojun

2017-01-01

In this publication, the interactive planning and reconstruction of cranial 3D Implants under the medical prototyping platform MeVisLab as alternative to commercial planning software is introduced. In doing so, a MeVisLab prototype consisting of a customized data-flow network and an own C++ module was set up. As a result, the Computer-Aided Design (CAD) software prototype guides a user through the whole workflow to generate an implant. Therefore, the workflow begins with loading and mirroring the patients head for an initial curvature of the implant. Then, the user can perform an additional Laplacian smoothing, followed by a Delaunay triangulation. The result is an aesthetic looking and well-fitting 3D implant, which can be stored in a CAD file format, e.g. STereoLithography (STL), for 3D printing. The 3D printed implant can finally be used for an in-depth pre-surgical evaluation or even as a real implant for the patient. In a nutshell, our research and development shows that a customized MeVisLab software prototype can be used as an alternative to complex commercial planning software, which may also not be available in every clinic. Finally, not to conform ourselves directly to available commercial software and look for other options that might improve the workflow. PMID:28264062

Happy software developers solve problems better: psychological measurements in empirical software engineering.

Science.gov (United States)

Graziotin, Daniel; Wang, Xiaofeng; Abrahamsson, Pekka

2014-01-01

For more than thirty years, it has been claimed that a way to improve software developers' productivity and software quality is to focus on people and to provide incentives to make developers satisfied and happy. This claim has rarely been verified in software engineering research, which faces an additional challenge in comparison to more traditional engineering fields: software development is an intellectual activity and is dominated by often-neglected human factors (called human aspects in software engineering research). Among the many skills required for software development, developers must possess high analytical problem-solving skills and creativity for the software construction process. According to psychology research, affective states-emotions and moods-deeply influence the cognitive processing abilities and performance of workers, including creativity and analytical problem solving. Nonetheless, little research has investigated the correlation between the affective states, creativity, and analytical problem-solving performance of programmers. This article echoes the call to employ psychological measurements in software engineering research. We report a study with 42 participants to investigate the relationship between the affective states, creativity, and analytical problem-solving skills of software developers. The results offer support for the claim that happy developers are indeed better problem solvers in terms of their analytical abilities. The following contributions are made by this study: (1) providing a better understanding of the impact of affective states on the creativity and analytical problem-solving capacities of developers, (2) introducing and validating psychological measurements, theories, and concepts of affective states, creativity, and analytical-problem-solving skills in empirical software engineering, and (3) raising the need for studying the human factors of software engineering by employing a multidisciplinary viewpoint.

Introduction to Lean Canvas Transformation Models and Metrics in Software Testing

Directory of Open Access Journals (Sweden)

Nidagundi Padmaraj

2016-05-01

Full Text Available Software plays a key role nowadays in all fields, from simple up to cutting-edge technologies and most of technology devices now work on software. Software development verification and validation have become very important to produce the high quality software according to business stakeholder requirements. Different software development methodologies have given a new dimension for software testing. In traditional waterfall software development software testing has approached the end point and begins with resource planning, a test plan is designed and test criteria are defined for acceptance testing. In this process most of test plan is well documented and it leads towards the time-consuming processes. For the modern software development methodology such as agile where long test processes and documentations are not followed strictly due to small iteration of software development and testing, lean canvas transformation models can be a solution. This paper provides a new dimension to find out the possibilities of adopting the lean transformation models and metrics in the software test plan to simplify the test process for further use of these test metrics on canvas.

Secure Software Configuration Management Processes for nuclear safety software development environment

International Nuclear Information System (INIS)

Chou, I.-Hsin

2011-01-01

Highlights: → The proposed method emphasizes platform-independent security processes. → A hybrid process based on the nuclear SCM and security regulations is proposed. → Detailed descriptions and Process Flow Diagram are useful for software developers. - Abstract: The main difference between nuclear and generic software is that the risk factor is infinitely greater in nuclear software - if there is a malfunction in the safety system, it can result in significant economic loss, physical damage or threat to human life. However, secure software development environment have often been ignored in the nuclear industry. In response to the terrorist attacks on September 11, 2001, the US Nuclear Regulatory Commission (USNRC) revised the Regulatory Guide (RG 1.152-2006) 'Criteria for use of computers in safety systems of nuclear power plants' to provide specific security guidance throughout the software development life cycle. Software Configuration Management (SCM) is an essential discipline in the software development environment. SCM involves identifying configuration items, controlling changes to those items, and maintaining integrity and traceability of them. For securing the nuclear safety software, this paper proposes a Secure SCM Processes (S 2 CMP) which infuses regulatory security requirements into proposed SCM processes. Furthermore, a Process Flow Diagram (PFD) is adopted to describe S 2 CMP, which is intended to enhance the communication between regulators and developers.

An Assessment between Software Development Life Cycle Models of Software Engineering

OpenAIRE

Er. KESHAV VERMA; Er. PRAMOD KUMAR; Er. MOHIT KUMAR; Er.GYANESH TIWARI

2013-01-01

This research deals with an essential and important subject in Digital world. It is related with the software managing processes that inspect the part of software development during the development models, which are called as software development life cycle. It shows five of the development models namely, waterfall, Iteration, V-shaped, spiral and Extreme programming. These models have advantages and disadvantages as well. So, the main objective of this research is to represent dissimilar mod...

A development methodology for scientific software

International Nuclear Information System (INIS)

Cort, G.; Barrus, D.M.; Goldstone, J.A.; Miller, L.; Nelson, R.O.; Poore, R.V.

1985-01-01

We present the details of a software development methodology that addresses all phases of the software life cycle, yet is well suited for application by small projects with limited resources. The methodology has been developed at the Los Alamos Weapons Neutron Research (WNR) Facility and was utilized during the recent development of the WNR Data Acquisition Command Language. The methodology emphasizes the development and maintenance of comprehensive documentation for all software components. The impact of the methodology upon software quality and programmer productivity is assessed

Software Development Standard Processes (SDSP)

Science.gov (United States)

Lavin, Milton L.; Wang, James J.; Morillo, Ronald; Mayer, John T.; Jamshidian, Barzia; Shimizu, Kenneth J.; Wilkinson, Belinda M.; Hihn, Jairus M.; Borgen, Rosana B.; Meyer, Kenneth N.;

Lean software development in action

CERN Document Server

Janes, Andrea

2014-01-01

This book illustrates how goal-oriented, automated measurement can be used to create Lean organizations and to facilitate the development of Lean software, while also demonstrating the practical implementation of Lean software development by combining tried and trusted tools. In order to be successful, a Lean orientation of software development has to go hand in hand with a company's overall business strategy. To achieve this, two interrelated aspects require special attention: measurement and experience management. In this book, Janes and Succi provide the necessary knowledge to establish "

Saltwell Leak Detector Station Programmable Logic Controller (PLC) Software Configuration Management Plan (SCMP)

International Nuclear Information System (INIS)

WHITE, K.A.

2000-01-01

This document provides the procedures and guidelines necessary for computer software configuration management activities during the operation and maintenance phases of the Saltwell Leak Detector Stations as required by HNF-PRO-309/Rev.1, Computer Software Quality Assurance, Section 2.4, Software Configuration Management. The software configuration management plan (SCMP) integrates technical and administrative controls to establish and maintain technical consistency among requirements, physical configuration, and documentation for the Saltwell Leak Detector Station Programmable Logic Controller (PLC) software during the Hanford application, operations and maintenance. This SCMP establishes the Saltwell Leak Detector Station PLC Software Baseline, status changes to that baseline, and ensures that software meets design and operational requirements and is tested in accordance with their design basis

Ongoing development of digital radiotherapy plan review tools

International Nuclear Information System (INIS)

Ebert, M.A.; Hatton, J.; Cornes, D.

2011-01-01

Full text: To describe ongoing development of software to support the review of radiotherapy treatment planning system (TPS) data. The 'SWAN' software program was conceived in 2000 and initially developed for the RADAR (TROG 03.04) prostate radiotherapy trial. Validation of the SWAN program has been occurring via implementation by TROG in support of multiple clinical trials. Development has continued and the SWAN software program is now supported by modular components which comprise the 'SW AN system'. This provides a comprehensive set of tools for the review, analysis and archive of TPS exports. The SWAN system has now been used in support of over 20 radiotherapy trials and to review the plans of over 2,000 trial participants. The use of the system for the RADAR trial is now culminating in the derivation of dose-outcomes indices for prostate treatment toxicity. Newly developed SWAN tools include enhanced remote data archive/retrieval, display of dose in both relative and absolute modes, and interfacing to a Matlab-based add-on ('VAST') that allows quantitative analysis of delineated volumes including regional overlap statistics for multi-observer studies. Efforts are continuing to develop the SWAN system in the context of international collaboration aimed at harmonising the quality-assurance activities of collaborative trials groups. Tools such as the SWAN system are essential for ensuring the collection of accurate and reliable evidence to guide future radiotherapy treatments. One of the principal challenges of developing such a tool is establishing a development path that will ensure its validity and applicability well into the future.

SigmaPlot 2000, Version 6.00, SPSS Inc. Computer Software Test Plan

Energy Technology Data Exchange (ETDEWEB)

HURLBUT, S.T.

2000-10-24

SigmaPlot is a vendor software product used in conjunction with the supercritical fluid extraction Fourier transform infrared spectrometer (SFE-FTIR) system. This product converts the raw spectral data to useful area numbers. SigmaPlot will be used in conjunction with procedure ZA-565-301, ''Determination of Moisture by Supercritical Fluid Extraction and Infrared Detection.'' This test plan will be performed in conjunction with or prior to HNF-6936, ''HA-53 Supercritical Fluid Extraction System Acceptance Test Plan'', to perform analyses for water. The test will ensure that the software can be installed properly and will manipulate the analytical data correctly.

Review of Ground Systems Development and Operations (GSDO) Tools for Verifying Command and Control Software

Science.gov (United States)

Aguilar, Michael L.; Bonanne, Kevin H.; Favretto, Jeffrey A.; Jackson, Maddalena M.; Jones, Stephanie L.; Mackey, Ryan M.; Sarrel, Marc A.; Simpson, Kimberly A.

2014-01-01

The Exploration Systems Development (ESD) Standing Review Board (SRB) requested the NASA Engineering and Safety Center (NESC) conduct an independent review of the plan developed by Ground Systems Development and Operations (GSDO) for identifying models and emulators to create a tool(s) to verify their command and control software. The NESC was requested to identify any issues or weaknesses in the GSDO plan. This document contains the outcome of the NESC review.

Educational Software: A Developer's Perspective.

Science.gov (United States)

Armstrong, Timothy C.; Loane, Russell F.

1994-01-01

Examines the current status and short-term future of computer software development in higher education. Topics discussed include educational advantages of software; current program development techniques, including object oriented programming; and market trends, including IBM versus Macintosh and multimedia programs. (LRW)

Master Pump Shutdown MPS Software Quality Assurance Plan (SQAP)

International Nuclear Information System (INIS)

BEVINS, R.R.

2000-01-01

The MPSS Software Quality Assurance (SQAP) describes the tools and strategy used in the development of the MPSS software. The document also describes the methodology for controlling and managing changes to the software

SOFTWARE PROCESS IMPROVEMENT: AWARENESS, USE, AND BENEFITS IN CANADIAN SOFTWARE DEVELOPMENT FIRMS

OpenAIRE

CHEVERS, DELROY

2017-01-01

ABSTRACT Since 1982, the software development community has been concerned with the delivery of quality systems. Software process improvement (SPI) is an initiative to avoid the delivery of low quality systems. However, the awareness and adoption of SPI is low. Thus, this study examines the rate of awareness, use, and benefits of SPI initiatives in Canadian software development firms. Using SPSS as the analytical tool, this study found that 59% of Canadian software development firms are aware...

TOGAF usage in outsourcing of software development

Directory of Open Access Journals (Sweden)

Aziz Ahmad Rais

2013-12-01

Full Text Available TOGAF is an Enterprise Architecture framework that provides a method for developing Enterprise Architecture called architecture development method (ADM. The purpose of this paper is whether TOGAF ADM can be used for developing software application architecture. Because the software application architecture is one of the disciplines in application development life cycle, it is important to find out how the enterprise architecture development method can support the application architecture development. Having an open standard that can be used in the application architecture development could help in outsourcing of software development. If ADM could be used for software application architecture development, then we could consider its usability in outsourcing of software development.

Six Sigma software development

CERN Document Server

Tayntor, Christine B

2002-01-01

Since Six Sigma has had marked success in improving quality in other settings, and since the quality of software remains poor, it seems a natural evolution to apply the concepts and tools of Six Sigma to system development and the IT department. Until now however, there were no books available that applied these concepts to the system development process. Six Sigma Software Development fills this void and illustrates how Six Sigma concepts can be applied to all aspects of the evolving system development process. It includes the traditional waterfall model and in the support of legacy systems,

Hospital Management Software Development

OpenAIRE

sobogunGod, olawale

2012-01-01

The purpose of this thesis was to implement a hospital management software which is suitable for small private hospitals in Nigeria, especially for the ones that use a file based system for storing information rather than having it stored in a more efficient and safer environment like databases or excel programming software. The software developed within this thesis project was specifically designed for the Rainbow specialist hospital which is based in Lagos, the commercial neurological cente...

Understanding flexible and distributed software development processes

OpenAIRE

Agerfalk, Par J.; Fitzgerald, Brian

2006-01-01

peer-reviewed The minitrack on Flexible and Distributed Software Development Processes addresses two important and partially intertwined current themes in software development: process flexibility and globally distributed software development

Planning the Unplanned Experiment: Towards Assessing the Efficacy of Standards for Safety-Critical Software

Science.gov (United States)

Graydon, Patrick J.; Holloway, C. M.

2015-01-01

Safe use of software in safety-critical applications requires well-founded means of determining whether software is fit for such use. While software in industries such as aviation has a good safety record, little is known about whether standards for software in safety-critical applications 'work' (or even what that means). It is often (implicitly) argued that software is fit for safety-critical use because it conforms to an appropriate standard. Without knowing whether a standard works, such reliance is an experiment; without carefully collecting assessment data, that experiment is unplanned. To help plan the experiment, we organized a workshop to develop practical ideas for assessing software safety standards. In this paper, we relate and elaborate on the workshop discussion, which revealed subtle but important study design considerations and practical barriers to collecting appropriate historical data and recruiting appropriate experimental subjects. We discuss assessing standards as written and as applied, several candidate definitions for what it means for a standard to 'work,' and key assessment strategies and study techniques and the pros and cons of each. Finally, we conclude with thoughts about the kinds of research that will be required and how academia, industry, and regulators might collaborate to overcome the noted barriers.

Waste receiving and processing facility module 1 data management system software project management plan

International Nuclear Information System (INIS)

Clark, R.E.

1994-01-01

This document provides the software development plan for the Waste Receiving and Processing (WRAP) Module 1 Data Management System (DMS). The DMS is one of the plant computer systems for the new WRAP 1 facility (Project W-026). The DMS will collect, store, and report data required to certify the low level waste (LLW) and transuranic (TRU) waste items processed at WRAP 1 as acceptable for shipment, storage, or disposal

Software Quality Perceptions of Stakeholders Involved in the Software Development Process

Science.gov (United States)

Padmanabhan, Priya

2013-01-01

Software quality is one of the primary determinants of project management success. Stakeholders involved in software development widely agree that quality is important (Barney and Wohlin 2009). However, they may differ on what constitutes software quality, and which of its attributes are more important than others. Although, software quality…

Software Quality Assurance and Controls Standard

Science.gov (United States)

2010-04-27

dassurance a wor pro uc s an processes comply with predefined provisions and plans. • According to International Standard (IS) 12207 – of the 44...from document (plan) focus to process focus – Alignment with framework standard IS 12207 software life cycle (SLC) processes with exact...Books and P blications IEEE Software and Systems Engineering curriculum ABET u Certified Software Development Professional Standards ISO /IEC

The software development process in worldwide collaborations

International Nuclear Information System (INIS)

Amako, K.

1998-01-01

High energy physics experiments in future colliders are inevitably large scale international collaborations. In these experiments, software development has to be done by a large number of physicists, software engineers and computer scientists, dispersed all over the world. The major subject of this paper is to discuss on various aspects of software development in the worldwide environment. These include software engineering and methodology, software development process and management. (orig.)

A Software Development Platform for Mechatronic Systems

DEFF Research Database (Denmark)

Guan, Wei

Software has become increasingly determinative for development of mechatronic systems, which underscores the importance of demands for shortened time-to-market, increased productivity, higher quality, and improved dependability. As the complexity of systems is dramatically increasing, these demands...... present a challenge to the practitioners who adopt conventional software development approach. An effective approach towards industrial production of software for mechatronic systems is needed. This approach requires a disciplined engineering process that encompasses model-driven engineering and component......-based software engineering, whereby we enable incremental software development using component models to address the essential design issues of real-time embedded systems. To this end, this dissertation presents a software development platform that provides an incremental model-driven development process based...

A Full-Featured User Friendly CO₂-EOR and Sequestration Planning Software

Energy Technology Data Exchange (ETDEWEB)

Savage, Bill [Nitec LLC, Denver, CO (United States)

2013-11-30

A Full-Featured, User Friendly CO₂-EOR and Sequestration Planning Software This project addressed the development of an integrated software solution that includes a graphical user interface, numerical simulation, visualization tools and optimization processes for reservoir simulation modeling of CO₂-EOR. The objective was to assist the industry in the development of domestic energy resources by expanding the application of CO₂-EOR technologies, and ultimately to maximize the CO₂} sequestration capacity of the U.S. The software resulted in a field-ready application for the industry to address the current CO₂-EOR technologies. The software has been made available to the public without restrictions and with user friendly operating documentation and tutorials. The software (executable only) can be downloaded from NITEC’s website at www.nitecllc.com. This integrated solution enables the design, optimization and operation of CO₂-EOR processes for small and mid-sized operators, who currently cannot afford the expensive, time intensive solutions that the major oil companies enjoy. Based on one estimate, small oil fields comprise 30% of the of total economic resource potential for the application of CO₂-EOR processes in the U.S. This corresponds to 21.7 billion barrels of incremental, technically recoverable oil using the current “best practices”, and 31.9 billion barrels using “next-generation” CO₂-EOR techniques. The project included a Case Study of a prospective CO₂-EOR candidate field in Wyoming by a small independent, Linc Energy Petroleum Wyoming, Inc. NITEC LLC has an established track record of developing innovative and user friendly software. The Principle Investigator is an experienced manager and engineer with expertise in software development, numerical techniques, and GUI applications. Unique, presently-proprietary NITEC technologies have been integrated

Trust in Co-sourced Software Development

DEFF Research Database (Denmark)

Schlichter, Bjarne Rerup; Persson, John Stouby

2014-01-01

Software development projects are increasingly geographical distributed with offshoring. Co-sourcing is a highly integrative and cohesive approach, seen successful, to software development offshoring. However, research of how dynamic aspects of trust are shaped in co-sourcing activities is limite...... understanding or personal trust relations. The paper suggests how certain work practices among developers and managers can be explained using a dynamic trust lens based on Abstract Systems, especially dis- and re-embedding mechanisms......Software development projects are increasingly geographical distributed with offshoring. Co-sourcing is a highly integrative and cohesive approach, seen successful, to software development offshoring. However, research of how dynamic aspects of trust are shaped in co-sourcing activities is limited...

Reviews in innovative software development

DEFF Research Database (Denmark)

Aaen, Ivan; Boelsmand, Jeppe Vestergaard; Jensen, Rasmus

2009-01-01

This paper proposes a new review approach for innovative software development. Innovative software development implies that requirements are rarely available as a basis for reviewing and that the purpose of a review is as much to forward additional ideas, as to validate what has been accomplished...

The NUKDOS software for treatment planning in molecular radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Kletting, Peter; Schimmel, Sebastian [Univ. Ulm (Germany). Klinik fuer Nuklearmedizin; Haenscheid, Heribert; Fernandez, Maria; Lassmann, Michael [Univ. Wuerzburg (Germany). Klinik fuer Nuklearmedizin; Luster, Markus [Univ. Marburg (Germany). Klinik fuer Nuklearmedizin; Nosske, Dietmar [Bundesamt fuer Strahlenschutz, Fachbereich Strahlenschutz und Gesundheit, Oberschleissheim (Germany); Glatting, Gerhard [Heidelberg Univ., Medical Radiation Physics/Radiation Protection, Mannheim (Germany)

2015-07-01

The aim of this work was the development of a software tool for treatment planning prior to molecular radiotherapy, which comprises all functionality to objectively determine the activity to administer and the pertaining absorbed doses (including the corresponding error) based on a series of gamma camera images and one SPECT/CT or probe data. NUKDOS was developed in MATLAB. The workflow is based on the MIRD formalism For determination of the tissue or organ pharmacokinetics, gamma camera images as well as probe, urine, serum and blood activity data can be processed. To estimate the time-integrated activity coefficients (TIAC), sums of exponentials are fitted to the time activity data and integrated analytically. To obtain the TIAC on the voxel level, the voxel activity distribution from the quantitative 3D SPECT/CT (or PET/CT) is used for scaling and weighting the TIAC derived from the 2D organ data. The voxel S-values are automatically calculated based on the voxel-size of the image and the therapeutic nuclide ({sup 90}Y, {sup 131}I or {sup 177}Lu). The absorbed dose coefficients are computed by convolution of the voxel TIAC and the voxel S-values. The activity to administer and the pertaining absorbed doses are determined by entering the absorbed dose for the organ at risk. The overall error of the calculated absorbed doses is determined by Gaussian error propagation. NUKDOS was tested for the operation systems Windows {sup registered} 7 (64 Bit) and 8 (64 Bit). The results of each working step were compared to commercially available (SAAMII, OLINDA/EXM) and in-house (UlmDOS) software. The application of the software is demonstrated using examples form peptide receptor radionuclide therapy (PRRT) and from radioiodine therapy of benign thyroid diseases. For the example from PRRT, the calculated activity to administer differed by 4% comparing NUKDOS and the final result using UlmDos, SAAMII and OLINDA/EXM sequentially. The absorbed dose for the spleen and tumour

Assessment of best practice of software development in developing ...

African Journals Online (AJOL)

... Understand the technology of the software (4.03), Memory limit set (3.91), Application pool not shared (3.88) and other parameters were examined for software development. The analysis shows the variance of the assessment of best practices in Software development firms and they are in conformity with the global trend.

Software Configuration Management Plan for the K West Basin Integrated Water Treatment System (IWTS) - Project A.9

International Nuclear Information System (INIS)

GREEN, J.W.

2000-01-01

This document provides a configuration control plan for the software associated with the operation and control of the Integrated Water Treatment System (IWTS). It establishes requirements for ensuring configuration item identification, configuration control, configuration status accounting, defect reporting and resolution of computer software. It is written to comply with HNF-SD-SNF-CM-001, Spent Nuclear Fuel Configuration Management Plan (Forehand 1998) and HNF-PRO-309 Computer Software Quality Assurance Requirements, and applicable sections of administrative procedure CM-6-037-00, SNF Project Process Automation Software and Equipment

RELAP-7 Software Verification and Validation Plan - Requirements Traceability Matrix (RTM) Part 2: Code Assessment Strategy, Procedure, and RTM Update

Energy Technology Data Exchange (ETDEWEB)

Yoo, Jun Soo [Idaho National Lab. (INL), Idaho Falls, ID (United States); Choi, Yong Joon [Idaho National Lab. (INL), Idaho Falls, ID (United States); Smith, Curtis Lee [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-09-01

This document addresses two subjects involved with the RELAP-7 Software Verification and Validation Plan (SVVP): (i) the principles and plan to assure the independence of RELAP-7 assessment through the code development process, and (ii) the work performed to establish the RELAP-7 assessment plan, i.e., the assessment strategy, literature review, and identification of RELAP-7 requirements. Then, the Requirements Traceability Matrices (RTMs) proposed in previous document (INL-EXT-15-36684) are updated. These RTMs provide an efficient way to evaluate the RELAP-7 development status as well as the maturity of RELAP-7 assessment through the development process.

Automating Object-Oriented Software Development Methods

NARCIS (Netherlands)

Tekinerdogan, B.; Saeki, Motoshi; Sunyé, Gerson; van den Broek, P.M.; Hruby, Pavel; Tekinerdogan, B.; van den Broek, P.M.; Saeki, M.; Hruby, P.; Sunye, G.

2001-01-01

Current software projects have generally to deal with producing and managing large and complex software products. It is generally believed that applying software development methods are useful in coping with this complexity and for supporting quality. As such numerous object-oriented software

Automating Object-Oriented Software Development Methods

NARCIS (Netherlands)

Tekinerdogan, B.; Frohner, A´ kos; Saeki, Motoshi; Sunyé, Gerson; van den Broek, P.M.; Hruby, Pavel

2002-01-01

Current software projects have generally to deal with producing and managing large and complex software products. It is generally believed that applying software development methods are useful in coping with this complexity and for supporting quality. As such numerous object-oriented software

A Practice of Secure Development and Operational Environment Plan

International Nuclear Information System (INIS)

Park, Jaekwan; Seo, Sangmun; Suh, Yongsukl; Park, Cheol

2017-01-01

This paper suggests a practice of plan for SDOE establishment in a nuclear I and C. First, it is necessary to perform a requirements analysis to define key regulatory issues and determine the target systems. The analysis includes a survey to find out the applicable measures credited internationally. Based on the analysis results, this paper proposes an implementation plan including a process harmonizing security activities with legacy software activities and applicable technical, operational, and management measures for target systems. Recently, nuclear I and C has been faced with two security issues, cyber security (CS) and secure development and operational environment (SDOE). Unlike cyber security, few studies on planning SDOE have been presented. This paper suggests a plan for establishing an SDOE in a nuclear I and C. This paper defines three key considerations to comply with the regulatory position of RG. 1.152(R3) and proposes a process harmonizing the security activities with legacy software activities. In addition, this paper proposes technical, operational, and management measures applicable for SDOE.

Workshop on Developing Safe Software

International Nuclear Information System (INIS)

Lawrence, J.D.

1994-11-01

The Workshop on Developing Safe Software was held July 22--23, 1992, at the Hotel del Coronado, San Diego, California. The purpose of the workshop was to have four world experts discuss among themselves software safety issues which are of interest to the US Nuclear Regulatory Commission. These issues concern the development of software systems for use in nuclear power plant protection systems. The workshop comprised four sessions. Wednesday morning, July 22, consisted of presentations from each of the four panel members. On Wednesday afternoon, the panel members went through a list of possible software development techniques and commented on them. The Thursday morning, July 23, session consisted of an extended discussion among the panel members and the observers from the NRC. A final session on Thursday afternoon consisted of a discussion among the NRC observers as to what was learned from the workshop

Workshop on developing safe software

International Nuclear Information System (INIS)

Lawrence, J.D.

1992-01-01

The Workshop on Developing Safe Software was held July 22--23 at the Hotel del Coronado, San Diego, California. The purpose of the workshop was to have four world experts discuss among themselves software safety issues which are of interest to the U. S. Nuclear Regulatory Commission (NRC). These issues concern the development of software systems for use in nuclear power plant protection systems. The workshop comprised four sessions. Wednesday morning, July 22, consisted of presentations from each of the four panel members. On Wednesday afternoon, the panel members went through a list of possible software development techniques and commented on them. The Thursday morning, July 23, session consisted of an extended discussion among the panel members and the observers from the NRC. A final session on Thursday afternoon consisted of a discussion among the NRC observers as to what was teamed from the workshop

Using iKidTools™ Software Support Systems to Develop and Implement Self-Monitoring Interventions

Science.gov (United States)

Patti, Angela L.; Miller, Kevin J.

2011-01-01

Educational teams often are faced with the task of developing and implementing Behavioral Intervention Plans (BIPs) for students who present challenging and/or disruptive behaviors. This article describes the steps used to develop and implement a self-monitoring BIP that incorporated an innovative software system, iKidTools™. An authentic case…

CDApps: integrated software for experimental planning and data processing at beamline B23, Diamond Light Source.

Science.gov (United States)

Hussain, Rohanah; Benning, Kristian; Javorfi, Tamas; Longo, Edoardo; Rudd, Timothy R; Pulford, Bill; Siligardi, Giuliano

2015-03-01

The B23 Circular Dichroism beamline at Diamond Light Source has been operational since 2009 and has seen visits from more than 200 user groups, who have generated large amounts of data. Based on the experience of overseeing the users' progress at B23, four key areas requiring the most assistance are identified: planning of experiments and note-keeping; designing titration experiments; processing and analysis of the collected data; and production of experimental reports. To streamline these processes an integrated software package has been developed and made available for the users. The subsequent article summarizes the main features of the software.

Manifesto for the Software Development Professionalization

Directory of Open Access Journals (Sweden)

Red Latinoamericana en Ingeniería de Software (RedLatinaIS

2013-12-01

Full Text Available One of the central problems of current economic development and industrial competitiveness, social and scientific, is the complexity of large and intensive software systems, and processes for their development and implementation. This complexity is defined by the amount and heterogeneity of the interaction of the hardware with the software components, their inter-relationships, of incorporation of the technical and organizational environments, and the interfaces to humans. The domain of these systems requires actions and scientific thoughts, hierarchical and systematic; also, the success of the products, services and organizations, is increasingly determined by the availability of suitable software products. Therefore, highly qualified professionals, able to understand and master the systems, involved in the entire life cycle of software engineering, and adopt different roles during the development. This is the reason that guide the thinking of this Manifesto , which aims is to achieve the Professionalization of Software Development.

EPRI's POWERCOACH trademark software development project

International Nuclear Information System (INIS)

Rost, S.; Leu, Kehshiou

1993-01-01

Today's complex bulk power market accounts for an estimated $35 billion in transactions a year, significantly more than a decade ago. With the increased levels of non-utility generation and changing strategies in the utility industry, it is anticipated that the trend toward rapid growth in the bulk power market will continue. This market has evolved from an ad hoc residual market to one that in some respects stands at par with the retail market in the plans of many utilities. The bulk power market is not based on the obligation to serve to the same extent as retail markets. Utility participation in this market is therefore purely voluntary. This freedom of action or inaction in the bulk power market actually renders corporate decision-making, investment related or operational, more complicated in many respects than in retail markets. Examples of the burgeoning uncertainties affecting the bulk power market include the rapid expansion of transactions undertaken through power pools, and the impact on utility planning and operations brought about by the abundance and price attractiveness of power available for flexible periods. These uncertainties present an ideal opportunity to employ state-of-the-art analytical models to facilitate the effective use of utility assets to foster the efficient functioning of the entire bulk power market. This paper will focus on the POWERCOACH methodology for short-term bulk power transaction analysis under conditions of uncertainty. In August 1992, UPMP began a seventeen month project to convert POWERCOACH from a methodology to a fully functional, commercial software package. UPMP is developing the POWERCOACH software with the extensive, direct involvement of thirty EPRI member utilities. A synopsis of POWERCOACH is presented

Stimulating Creativity Through Opportunistic Software Development

NARCIS (Netherlands)

Z. Obrenovic; D. Gasevic; A. P. W. Eliëns (Anton)

2008-01-01

htmlabstractUsing opportunistic software development principles in computer engineering education encourages students to be creative and to develop solutions that cross the boundaries of diverse technologies. A framework for opportunistic software development education helps to create a space in

Stimulating creativity through opportunistic software development

NARCIS (Netherlands)

Obrenovic, Z.; Gasevic, D.; Eliëns, A.

2008-01-01

Using opportunistic software development principles in computer engineering education encourages students to be creative and to develop solutions that cross the boundaries of diverse technologies. A framework for opportunistic software development education helps to create a space in which students

Software for Optimizing Quality Assurance of Other Software

Science.gov (United States)

Feather, Martin; Cornford, Steven; Menzies, Tim

2004-01-01

Software assurance is the planned and systematic set of activities that ensures that software processes and products conform to requirements, standards, and procedures. Examples of such activities are the following: code inspections, unit tests, design reviews, performance analyses, construction of traceability matrices, etc. In practice, software development projects have only limited resources (e.g., schedule, budget, and availability of personnel) to cover the entire development effort, of which assurance is but a part. Projects must therefore select judiciously from among the possible assurance activities. At its heart, this can be viewed as an optimization problem; namely, to determine the allocation of limited resources (time, money, and personnel) to minimize risk or, alternatively, to minimize the resources needed to reduce risk to an acceptable level. The end result of the work reported here is a means to optimize quality-assurance processes used in developing software.

Software cost estimation

NARCIS (Netherlands)

Heemstra, F.J.

1992-01-01

The paper gives an overview of the state of the art of software cost estimation (SCE). The main questions to be answered in the paper are: (1) What are the reasons for overruns of budgets and planned durations? (2) What are the prerequisites for estimating? (3) How can software development effort be

Software cost estimation

NARCIS (Netherlands)

Heemstra, F.J.; Heemstra, F.J.

1993-01-01

The paper gives an overview of the state of the art of software cost estimation (SCE). The main questions to be answered in the paper are: (1) What are the reasons for overruns of budgets and planned durations? (2) What are the prerequisites for estimating? (3) How can software development effort be

77 FR 19280 - Increasing Market and Planning Efficiency Through Improved Software; Notice of Technical...

Science.gov (United States)

2012-03-30

... concerns that current system data quality might not allow for an AC optimal power flow model to be properly... Market and Planning Efficiency Through Improved Software; Notice of Technical Conference: Increasing Real-Time and Day- Ahead Market Efficiency Through Improved Software Take notice that Commission staff will...

Software development: do good manners matter?

Directory of Open Access Journals (Sweden)

Giuseppe Destefanis

2016-07-01

Full Text Available A successful software project is the result of a complex process involving, above all, people. Developers are the key factors for the success of a software development process, not merely as executors of tasks, but as protagonists and core of the whole development process. This paper investigates social aspects among developers working on software projects developed with the support of Agile tools. We studied 22 open-source software projects developed using the Agile board of the JIRA repository. All comments committed by developers involved in the projects were analyzed and we explored whether the politeness of comments affected the number of developers involved and the time required to fix any given issue. Our results showed that the level of politeness in the communication process among developers does have an effect on the time required to fix issues and, in the majority of the analysed projects, it had a positive correlation with attractiveness of the project to both active and potential developers. The more polite developers were, the less time it took to fix an issue.

Strategic Planning and Decision Analysis: Presentation of the COSIMA Software System

DEFF Research Database (Denmark)

This paper presents a composite decision support system, COSIMA, programmed in MS Excel. COSIMA provides assistance to the decision maker as concerns complex decisions and strategic planning. The COSIMA software is designed as interconnected modules which make it possible to conduct Cost-Benefit...

Alinhando objetivos estratégicos e processo de desenvolvimento em empresas de software Aligning strategic objectives and development practices at software companies

Directory of Open Access Journals (Sweden)

André Leme Fleury

2013-01-01

activities and how to guarantee that the development process is aligned with business goals. Resulting approach includes a referential to analyze software companies and a technique to develop technological plans for these companies. Research project included the development of surveys, action-researches and case studies.

Computer software configuration management plan for 200 East/West Liquid Effluent Facilities

Energy Technology Data Exchange (ETDEWEB)

Graf, F.A. Jr.

1995-02-27

This computer software management configuration plan covers the control of the software for the monitor and control system that operates the Effluent Treatment Facility and its associated truck load in station and some key aspects of the Liquid Effluent Retention Facility that stores condensate to be processed. Also controlled is the Treated Effluent Disposal System`s pumping stations and monitors waste generator flows in this system as well as the Phase Two Effluent Collection System.

Computer software configuration management plan for 200 East/West Liquid Effluent Facilities

International Nuclear Information System (INIS)

Graf, F.A. Jr.

1995-01-01

This computer software management configuration plan covers the control of the software for the monitor and control system that operates the Effluent Treatment Facility and its associated truck load in station and some key aspects of the Liquid Effluent Retention Facility that stores condensate to be processed. Also controlled is the Treated Effluent Disposal System's pumping stations and monitors waste generator flows in this system as well as the Phase Two Effluent Collection System

Software development for geologic information management system on open-pit production

Energy Technology Data Exchange (ETDEWEB)

Li, K.; Tian, A.; Ren, Z.; Pang, Y. [China University of Mining and Technomogy, Xuzhou (China). College of Mineral and Energy Resources

2001-09-01

A software, including geological data gathering and processing, deposit modelling, reserves calculating and mine map plotting, for geologic information management of open-pit production was developed. Based on the interactive technique, CAD, the object-oriented simulation, and the characteristics of geologic structures, all the geologic information databases and geologic mapping sub-systems have been established for open-pit production, planning and management. 6 refs., 1 fig.

Teaching land-use planning in a flood prone area with an educational software

Science.gov (United States)

Metzger, R.; Jaboyedoff, M.

2009-04-01

Teaching of flood risk mapping and mitigation is a necessary task in geosciences studies. However, there is often a gap between the theoretical hydraulic notions broached during the courses and the possibility to make use of them in practice by the students during supervised computer lab exercises. This is mainly due because professional models/software have a steep learning curve and the lecturer spend most of his time to explain how to make such or such operation with the software. To overcome this shortcoming, an educational software was developed, which is made of three main modules: 1) A user-friendly graphical interface (GUI), allowing for handling geographical data and creating thematic maps (Geographical Information System (GIS) module); 2) A flood model (hydrological and inundation models) part allowing for freeing student as much as possible from the repetitive and tedious tasks related to modeling issues, while keeping reasonable computational time; 3) A land use planning module, which allow for specifying mitigation measures (dikes and levees building, flood retention, renaturation, …) and for evaluating their effects by re-running the flood model. The main goal of this educational software is to provide a smooth approach to the modeling issue, without loosing the focus on the main task which is flood risk reduction.

Application of agile methodologies in software development

Directory of Open Access Journals (Sweden)

Jovanović Aca D.

2016-01-01

Full Text Available The paper presents the potentials for the development of software using agile methodologies. Special consideration is devoted to the potentials and advantages of use of the Scrum methodology in the development of software and the relationship between the implementation of agile methodologies and the software development projects.

Perspectives on Open Source Software

National Research Council Canada - National Science Library

Hissam, Scott

2001-01-01

Open source software (OSS) is emerging as the software community's next "silver bullet" and appears to be playing a significant role in the acquisition and development plans of the Department of Defense (DoD) and industry...

Computer software configuration management plan for the Honeywell modular automation system

International Nuclear Information System (INIS)

Cunningham, L.T.

1997-01-01

This document provides a Computer Software management plan for a new Honeywell Modular Automation System (MAS) being installed in the Plutonium Finishing Plant (PFP). This type of system will be used to control new thermal stabilization furnaces, a vertical denitrator calciner, and a pyrolysis furnace

Next Generation Software Development

National Research Council Canada - National Science Library

Manna, Zohar

2005-01-01

Under this grant we have studied the development of a scientifically sound basis for software development that builds on widely used pragmatic methods but is firmly grounded in well-established formal...

Developing software for safety-critical applications

International Nuclear Information System (INIS)

Chudleigh, M.

1989-01-01

The effective implementation of many safety-critical systems involves microprocessors running software which needs to be of very high integrity. This article describes some of the problems of producing such software and the place of software within the total system. A development strategy is proposed based on three principles: the goal of defect-free development, the use of mathematical formalism, and the use of an independent team for testing. (author)

Software-Engineering Process Simulation (SEPS) model

Science.gov (United States)

Lin, C. Y.; Abdel-Hamid, T.; Sherif, J. S.

1992-01-01

The Software Engineering Process Simulation (SEPS) model is described which was developed at JPL. SEPS is a dynamic simulation model of the software project development process. It uses the feedback principles of system dynamics to simulate the dynamic interactions among various software life cycle development activities and management decision making processes. The model is designed to be a planning tool to examine tradeoffs of cost, schedule, and functionality, and to test the implications of different managerial policies on a project's outcome. Furthermore, SEPS will enable software managers to gain a better understanding of the dynamics of software project development and perform postmodern assessments.

Software for planning processes gamma irradiation sterilization of products intended for health care

International Nuclear Information System (INIS)

Gonzalez, Juan P; Carrillo, Miguel A; Mangussi, Josefina; Menendez, Franco

2012-01-01

In this work was developed an application software for PC, with a friendly interface whose main objective is to facilitate the planning processes for gamma irradiation of health care devices for a irradiation plant, decreasing costs and delays caused in the dosimetry and pretesting. Wascreated a program that predicts, previously establishing the location of a plane in the enclosure of irradiation, dose rate in [kGy/h] at certain strategic points of this plane in addition to calculating the corresponding absorbed dose [kGy] for a time defined by the user (author)

The manual of a computer software 'FBR Plant Planning Design Prototype System'

International Nuclear Information System (INIS)

2003-10-01

This is a manual of a computer software 'FBR Plant Planning Design Prototype System', which enables users to conduct case studies of deviated FBR design concepts based on 'MONJU'. The calculations simply proceed as the user clicks displayed buttons, therefore step-by-step explanation is supposed not be necessary. The following pages introduce only particular features of this software, i.e, each interactive screens, functions of buttons and consequences after clicks, and the quitting procedure. (author)

SU-F-T-94: Plan2pdf - a Software Tool for Automatic Plan Report for Philips Pinnacle TPS

Energy Technology Data Exchange (ETDEWEB)

Wu, C [Sutter Medical Foundation, Roseville, CA (United States)

2016-06-15

Purpose: To implement an automatic electronic PDF plan reporting tool for Philips Pinnacle treatment planning system (TPS) Methods: An electronic treatment plan reporting software is developed by us to enable fully automatic PDF report from Pinnacle TPS to external EMR programs such as MOSAIQ. The tool is named “plan2pdf”. plan2pdf is implemented using Pinnacle scripts, Java and UNIX shell scripts, without any external program needed. plan2pdf supports full auto-mode and manual mode reporting. In full auto-mode, with a single mouse click, plan2pdf will generate a detailed Pinnacle plan report in PDF format, which includes customizable cover page, Pinnacle plan summary, orthogonal views through each plan POI and maximum dose point, DRR for each beam, serial transverse views captured throughout the dose grid at a user specified interval, DVH and scorecard windows. The final PDF report is also automatically bookmarked for each section above for convenient plan review. The final PDF report can either be saved on a user specified folder on Pinnacle, or it can be automatically exported to an EMR import folder via a user configured FTP service. In manual capture mode, plan2pdf allows users to capture any Pinnacle plan by full screen, individual window or rectangular ROI drawn on screen. Furthermore, to avoid possible patients’ plan mix-up during auto-mode reporting, a user conflict check feature is included in plan2pdf: it prompts user to wait if another patient is being exported by plan2pdf by another user. Results: plan2pdf is tested extensively and successfully at our institution consists of 5 centers, 15 dosimetrists and 10 physicists, running Pinnacle version 9.10 on Enterprise servers. Conclusion: plan2pdf provides a highly efficient, user friendly and clinical proven platform for all Philips Pinnacle users, to generate a detailed plan report in PDF format for external EMR systems.

SU-F-T-94: Plan2pdf - a Software Tool for Automatic Plan Report for Philips Pinnacle TPS

International Nuclear Information System (INIS)

Wu, C

2016-01-01

Purpose: To implement an automatic electronic PDF plan reporting tool for Philips Pinnacle treatment planning system (TPS) Methods: An electronic treatment plan reporting software is developed by us to enable fully automatic PDF report from Pinnacle TPS to external EMR programs such as MOSAIQ. The tool is named “plan2pdf”. plan2pdf is implemented using Pinnacle scripts, Java and UNIX shell scripts, without any external program needed. plan2pdf supports full auto-mode and manual mode reporting. In full auto-mode, with a single mouse click, plan2pdf will generate a detailed Pinnacle plan report in PDF format, which includes customizable cover page, Pinnacle plan summary, orthogonal views through each plan POI and maximum dose point, DRR for each beam, serial transverse views captured throughout the dose grid at a user specified interval, DVH and scorecard windows. The final PDF report is also automatically bookmarked for each section above for convenient plan review. The final PDF report can either be saved on a user specified folder on Pinnacle, or it can be automatically exported to an EMR import folder via a user configured FTP service. In manual capture mode, plan2pdf allows users to capture any Pinnacle plan by full screen, individual window or rectangular ROI drawn on screen. Furthermore, to avoid possible patients’ plan mix-up during auto-mode reporting, a user conflict check feature is included in plan2pdf: it prompts user to wait if another patient is being exported by plan2pdf by another user. Results: plan2pdf is tested extensively and successfully at our institution consists of 5 centers, 15 dosimetrists and 10 physicists, running Pinnacle version 9.10 on Enterprise servers. Conclusion: plan2pdf provides a highly efficient, user friendly and clinical proven platform for all Philips Pinnacle users, to generate a detailed plan report in PDF format for external EMR systems.

Firing Room Remote Application Software Development

Science.gov (United States)

Liu, Kan

2015-01-01

The Engineering and Technology Directorate (NE) at National Aeronautics and Space Administration (NASA) Kennedy Space Center (KSC) is designing a new command and control system for the checkout and launch of Space Launch System (SLS) and future rockets. The purposes of the semester long internship as a remote application software developer include the design, development, integration, and verification of the software and hardware in the firing rooms, in particular with the Mobile Launcher (ML) Launch Accessories (LACC) subsystem. In addition, a software test verification procedure document was created to verify and checkout LACC software for Launch Equipment Test Facility (LETF) testing.

Safety critical software development qualification

International Nuclear Information System (INIS)

Marron, J. E.

2006-01-01

With the increasing use of digital systems in control applications, customers must acquire appropriate expectations for software development and quality assurance procedures. Purchasers and users of digital systems need to understand the benefits to the supplier of effective quality systems. These systems consist not only of procedures but tools that enable automation. Without the use of automation, quality can not be assured. A software and systems quality program starts with the documents you are very familiar with. But these documents must define more than the final system. They must address specific development environment characteristics and testing capabilities. Starting with the RFP, some of the items that should be introduced are Software Configuration Management, regression testing and defect tracking. The digital system customer is in the best position to enforce the use of software and systems quality programs by including them in project requirements as early as the Purchase Order. The customer's understanding of the full scope and implementation of a software quality program is essential to achieving the quality necessary in nuclear projects, and, incidentally, completing those projects on schedule. (authors)

Workflow-Based Software Development Environment

Science.gov (United States)

Izygon, Michel E.

2013-01-01

The Software Developer's Assistant (SDA) helps software teams more efficiently and accurately conduct or execute software processes associated with NASA mission-critical software. SDA is a process enactment platform that guides software teams through project-specific standards, processes, and procedures. Software projects are decomposed into all of their required process steps or tasks, and each task is assigned to project personnel. SDA orchestrates the performance of work required to complete all process tasks in the correct sequence. The software then notifies team members when they may begin work on their assigned tasks and provides the tools, instructions, reference materials, and supportive artifacts that allow users to compliantly perform the work. A combination of technology components captures and enacts any software process use to support the software lifecycle. It creates an adaptive workflow environment that can be modified as needed. SDA achieves software process automation through a Business Process Management (BPM) approach to managing the software lifecycle for mission-critical projects. It contains five main parts: TieFlow (workflow engine), Business Rules (rules to alter process flow), Common Repository (storage for project artifacts, versions, history, schedules, etc.), SOA (interface to allow internal, GFE, or COTS tools integration), and the Web Portal Interface (collaborative web environment

Development methodology for the software life cycle process of the safety software

Energy Technology Data Exchange (ETDEWEB)

Kim, D. H.; Lee, S. S. [BNF Technology, Taejon (Korea, Republic of); Cha, K. H.; Lee, C. S.; Kwon, K. C.; Han, H. B. [KAERI, Taejon (Korea, Republic of)

2002-05-01

A methodology for developing software life cycle processes (SLCP) is proposed to develop the digital safety-critical Engineered Safety Features - Component Control System (ESF-CCS) successfully. A software life cycle model is selected as the hybrid model mixed with waterfall, prototyping, and spiral models and is composed of two stages , development stages of prototype of ESF-CCS and ESF-CCS. To produce the software life cycle (SLC) for the Development of the Digital Reactor Safety System, the Activities referenced in IEEE Std. 1074-1997 are mapped onto the hybrid model. The SLCP is established after the available OPAs (Organizational Process Asset) are applied to the SLC Activities, and the known constraints are reconciled. The established SLCP describes well the software life cycle activities with which the Regulatory Authority provides.

Development methodology for the software life cycle process of the safety software

International Nuclear Information System (INIS)

Kim, D. H.; Lee, S. S.; Cha, K. H.; Lee, C. S.; Kwon, K. C.; Han, H. B.

2002-01-01

A methodology for developing software life cycle processes (SLCP) is proposed to develop the digital safety-critical Engineered Safety Features - Component Control System (ESF-CCS) successfully. A software life cycle model is selected as the hybrid model mixed with waterfall, prototyping, and spiral models and is composed of two stages , development stages of prototype of ESF-CCS and ESF-CCS. To produce the software life cycle (SLC) for the Development of the Digital Reactor Safety System, the Activities referenced in IEEE Std. 1074-1997 are mapped onto the hybrid model. The SLCP is established after the available OPAs (Organizational Process Asset) are applied to the SLC Activities, and the known constraints are reconciled. The established SLCP describes well the software life cycle activities with which the Regulatory Authority provides

Space and Missile Systems Center Standard: Software Development

Science.gov (United States)

2015-01-16

waterfall development lifecycle models . Source: Adapted from (IEEE 610.12) See (IEEE 1074) for more information. Software ...spiral, and waterfall lifecycle models .) 2. The developer shall record the selected software development lifecycle model (s) in the Software ...through i.e., waterfall , lifecycle model , the following requirements apply with the interpretation that the software is developed as a single build.

RELAP-7 Software Verification and Validation Plan: Requirements Traceability Matrix (RTM) Part 1 – Physics and numerical methods

Energy Technology Data Exchange (ETDEWEB)

Choi, Yong Joon [Idaho National Lab. (INL), Idaho Falls, ID (United States); Yoo, Jun Soo [Idaho National Lab. (INL), Idaho Falls, ID (United States); Smith, Curtis Lee [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-09-01

This INL plan comprehensively describes the Requirements Traceability Matrix (RTM) on main physics and numerical method of the RELAP-7. The plan also describes the testing-based software verification and validation (SV&V) process—a set of specially designed software models used to test RELAP-7.

Optimal integration and test plans for software releases of lithographic systems

NARCIS (Netherlands)

Boumen, R.; Jong, de I.S.M.; Mortel - Fronczak, van de J.M.; Rooda, J.E.

2007-01-01

This paper describes a method to determine the optimal integration and test plan for embedded systems software releases. The method consists of four steps: 1)describe the integration and test problem in an integration and test model which is introduced in this paper, 2) determine possible test

Waste Management facilities cost information: System Cost Model Software Quality Assurance Plan. Revision 2

International Nuclear Information System (INIS)

Peterson, B.L.; Lundeen, A.S.

1996-02-01

In May of 1994, Lockheed Idaho Technologies Company (LITCO) in Idaho Falls, Idaho and subcontractors developed the System Cost Model (SCM) application. The SCM estimates life-cycle costs of the entire US Department of Energy (DOE) complex for designing; constructing; operating; and decommissioning treatment, storage, and disposal (TSD) facilities for mixed low-level, low-level, transuranic, and mixed transuranic waste. The SCM uses parametric cost functions to estimate life-cycle costs for various treatment, storage, and disposal modules which reflect planned and existing facilities at DOE installations. In addition, SCM can model new facilities based on capacity needs over the program life cycle. The SCM also provides transportation costs for truck and rail, which include transport of contact-handled, remote-handled, and alpha (transuranic) wastes. The user can provide input data (default data is included in the SCM) including the volume and nature of waste to be managed, the time period over which the waste is to be managed, and the configuration of the waste management complex (i.e., where each installation's generated waste will be treated, stored, and disposed). Then the SCM uses parametric cost equations to estimate the costs of pre-operations (designing), construction costs, operation management, and decommissioning these waste management facilities. For the product to be effective and useful the SCM users must have a high level of confidence in the data generated by the software model. The SCM Software Quality Assurance Plan is part of the overall SCM project management effort to ensure that the SCM is maintained as a quality product and can be relied on to produce viable planning data. This document defines tasks and deliverables to ensure continued product integrity, provide increased confidence in the accuracy of the data generated, and meet the LITCO's quality standards during the software maintenance phase. 8 refs., 1 tab

Waste Management facilities cost information: System Cost Model Software Quality Assurance Plan. Revision 2

Energy Technology Data Exchange (ETDEWEB)

Peterson, B.L.; Lundeen, A.S.

1996-02-01

In May of 1994, Lockheed Idaho Technologies Company (LITCO) in Idaho Falls, Idaho and subcontractors developed the System Cost Model (SCM) application. The SCM estimates life-cycle costs of the entire US Department of Energy (DOE) complex for designing; constructing; operating; and decommissioning treatment, storage, and disposal (TSD) facilities for mixed low-level, low-level, transuranic, and mixed transuranic waste. The SCM uses parametric cost functions to estimate life-cycle costs for various treatment, storage, and disposal modules which reflect planned and existing facilities at DOE installations. In addition, SCM can model new facilities based on capacity needs over the program life cycle. The SCM also provides transportation costs for truck and rail, which include transport of contact-handled, remote-handled, and alpha (transuranic) wastes. The user can provide input data (default data is included in the SCM) including the volume and nature of waste to be managed, the time period over which the waste is to be managed, and the configuration of the waste management complex (i.e., where each installation`s generated waste will be treated, stored, and disposed). Then the SCM uses parametric cost equations to estimate the costs of pre-operations (designing), construction costs, operation management, and decommissioning these waste management facilities. For the product to be effective and useful the SCM users must have a high level of confidence in the data generated by the software model. The SCM Software Quality Assurance Plan is part of the overall SCM project management effort to ensure that the SCM is maintained as a quality product and can be relied on to produce viable planning data. This document defines tasks and deliverables to ensure continued product integrity, provide increased confidence in the accuracy of the data generated, and meet the LITCO`s quality standards during the software maintenance phase. 8 refs., 1 tab.

MEDBASE: Strategic Planning and Implementation of an Army Medical Department Software Application

Science.gov (United States)

2003-07-17

downtime procedures) Software/ hardware performance testing Contingency plans Celebration / people management Risk Zone 4 Planning for upgrades...goal to “Crush Adidas !” and Honda’s goal in 1970 to “destroy Yamaha!”. MEDBASE: Strategy and Implementation 57 (3) Role Model BHAGs suit up-and...Crush Adidas ! (Nike, 1960s) Yamaha so tsubusu! We will destroy Yamaha! (Honda, 1970s) Role-Model BHAGs suit up-and-coming organizations Become the

The advanced software development workstation project

Science.gov (United States)

Fridge, Ernest M., III; Pitman, Charles L.

1991-01-01

The Advanced Software Development Workstation (ASDW) task is researching and developing the technologies required to support Computer Aided Software Engineering (CASE) with the emphasis on those advanced methods, tools, and processes that will be of benefit to support all NASA programs. Immediate goals are to provide research and prototype tools that will increase productivity, in the near term, in projects such as the Software Support Environment (SSE), the Space Station Control Center (SSCC), and the Flight Analysis and Design System (FADS) which will be used to support the Space Shuttle and Space Station Freedom. Goals also include providing technology for development, evolution, maintenance, and operations. The technologies under research and development in the ASDW project are targeted to provide productivity enhancements during the software life cycle phase of enterprise and information system modeling, requirements generation and analysis, system design and coding, and system use and maintenance. On-line user's guides will assist users in operating the developed information system with knowledge base expert assistance.

Integrating Usability Evaluations into the Software Development Process

DEFF Research Database (Denmark)

Lizano, Fulvio

as relevant and strategic human–computer interaction (HCI) activities in the software development process, there are obstacles that limit the complete, effective and efficient integration of this kind of testing into the software development process. Two main obstacles are the cost of usability evaluations...... and the software developers' resistance to accepting users’ opinions regarding the lack of usability in their software systems. The ‘cost obstacle’ refers to the constraint of conducting usability evaluations in the software process due to the significant amount of resources required by this type of testing. Some......This thesis addresses the integration of usability evaluations into the software development process. The integration here is contextualized in terms of how to include usability evaluation as an activity in the software development lifecycle. Even though usability evaluations are considered...

Advanced communications technology satellite high burst rate link evaluation terminal power control and rain fade software test plan, version 1.0

Science.gov (United States)

Reinhart, Richard C.

1993-01-01

The Power Control and Rain Fade Software was developed at the NASA Lewis Research Center to support the Advanced Communications Technology Satellite High Burst Rate Link Evaluation Terminal (ACTS HBR-LET). The HBR-LET is an experimenters terminal to communicate with the ACTS for various experiments by government, university, and industry agencies. The Power Control and Rain Fade Software is one segment of the Control and Performance Monitor (C&PM) Software system of the HBR-LET. The Power Control and Rain Fade Software automatically controls the LET uplink power to compensate for signal fades. Besides power augmentation, the C&PM Software system is also responsible for instrument control during HBR-LET experiments, control of the Intermediate Frequency Switch Matrix on board the ACTS to yield a desired path through the spacecraft payload, and data display. The Power Control and Rain Fade Software User's Guide, Version 1.0 outlines the commands and procedures to install and operate the Power Control and Rain Fade Software. The Power Control and Rain Fade Software Maintenance Manual, Version 1.0 is a programmer's guide to the Power Control and Rain Fade Software. This manual details the current implementation of the software from a technical perspective. Included is an overview of the Power Control and Rain Fade Software, computer algorithms, format representations, and computer hardware configuration. The Power Control and Rain Fade Test Plan provides a step-by-step procedure to verify the operation of the software using a predetermined signal fade event. The Test Plan also provides a means to demonstrate the capability of the software.

A systematic approach for component-based software development

NARCIS (Netherlands)

Guareis de farias, Cléver; van Sinderen, Marten J.; Ferreira Pires, Luis

2000-01-01

Component-based software development enables the construction of software artefacts by assembling prefabricated, configurable and independently evolving building blocks, called software components. This paper presents an approach for the development of component-based software artefacts. This

[Computers in nursing: development of free software application with care and management].

Science.gov (United States)

dos Santos, Sérgio Ribeiro

2010-06-01

This study aimed at developing an information system in nursing with the implementation of nursing care and management of the service. The SisEnf--Information System in Nursing--is a free software module that comprises the care of nursing: history, clinical examination and care plan; the management module consists of: service shifts, personnel management, hospital indicators and other elements. The system was implemented at the Medical Clinic of the Lauro Wanderley University Hospital, at Universidade Federal da Paraiba. In view of the need to bring user and developer closer, in addition to the constant change of functional requirements during the interactive process, the method of unified process was used. The SisEnf was developed on a WEB platform and using free software. Hence, the work developed aimed at assisting in the working process of nursing, which will now have the opportunity to incorporate information technology in their work routine.

Software configuration management plan for the TWRS controlled baseline database system [TCBD

International Nuclear Information System (INIS)

Spencer, S.G.

1998-01-01

the software transferred to the system owner. The primary programming for the TCBD was developed by Selfware, Inc. The Automatic Data Processing (ADP) Acquisition Plan, Systems Development and Support Services for TWRS Performance Measurement and Control System, Acquisition Plan No. C94-705286 identifies work scope, deliverables, and cost

Learning Human Aspects of Collaborative Software Development

Science.gov (United States)

Hadar, Irit; Sherman, Sofia; Hazzan, Orit

2008-01-01

Collaboration has become increasingly widespread in the software industry as systems have become larger and more complex, adding human complexity to the technological complexity already involved in developing software systems. To deal with this complexity, human-centric software development methods, such as Extreme Programming and other agile…

Development strategies for the satellite flight software on-board Meteosat Third Generation

Science.gov (United States)

Tipaldi, Massimo; Legendre, Cedric; Koopmann, Olliver; Ferraguto, Massimo; Wenker, Ralf; D'Angelo, Gianni

2018-04-01

Nowadays, satellites are becoming increasingly software dependent. Satellite Flight Software (FSW), that is to say, the application software running on the satellite main On-Board Computer (OBC), plays a relevant role in implementing complex space mission requirements. In this paper, we examine relevant technical approaches and programmatic strategies adopted for the development of the Meteosat Third Generation Satellite (MTG) FSW. To begin with, we present its layered model-based architecture, and the means for ensuring a robust and reliable interaction among the FSW components. Then, we focus on the selection of an effective software development life cycle model. In particular, by combining plan-driven and agile approaches, we can fulfill the need of having preliminary SW versions. They can be used for the elicitation of complex system-level requirements as well as for the initial satellite integration and testing activities. Another important aspect can be identified in the testing activities. Indeed, very demanding quality requirements have to be fulfilled in satellite SW applications. This manuscript proposes a test automation framework, which uses an XML-based test procedure language independent of the underlying test environment. Finally, a short overview of the MTG FSW sizing and timing budgets concludes the paper.

Verification and software validation for nuclear instrumentation; Verificacion y validacion de software para instrumentacion nuclear

Energy Technology Data Exchange (ETDEWEB)

Gaytan G, E. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Salgado G, J. R. [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Barragan No. 779, Col. Narvarte, 03020 Mexico D. F. (Mexico); De Andrade O, E. [Universidad Federal de Rio de Janeiro, Caixa Postal 68509, 21945-970 Rio de Janeiro (Brazil); Ramirez G, A., E-mail: elvira.gaytan@inin.gob.mx [Comision Federal de Electricidad, Gerencia de Centrales Nucleoelectricas, Alto Lucero, Veracruz (Mexico)

2014-10-15

In this work is presented a Verification Methodology and Software Validation, to be applied in instruments of nuclear use with associate software. This methodology was developed under the auspices of IAEA, through the regional projects RLA4022 (ARCAL XCIX) and RLA1011 (RLA CXXIII), led by Mexico. In the first project three plans and three procedures were elaborated taking into consideration IEEE standards, and in the second project these documents were updated considering ISO and IEC standards. The developed methodology has been distributed to the participant countries of Latin America in the ARCAL projects and two related courses have been imparted with the participation of several countries, and participating institutions of Mexico like Instituto Nacional de Investigaciones Nucleares (ININ), Comision Federal de Electricidad (CFE) and Comision Nacional de Seguridad Nuclear y Salvaguardias (CNSNS). In the ININ due to the necessity to work with Software Quality Guarantee in systems for the nuclear power plant of the CFE, a Software Quality Guarantee Plan and five procedures were developed in the year 2004, obtaining the qualification of the ININ for software development for the nuclear power plant of CFE. These first documents were developed taking like reference IEEE standards and regulator guides of NRC, being the first step for the development of the methodology. (Author)

Developing free software for automatic registration for the quality control of IMRT with movies; Desarrollo de un software gratuito para el registro automatico durante el control de calidad de la IMRT con peliculas

Energy Technology Data Exchange (ETDEWEB)

Moral, F. del; Meilan, E.; Pereira, L.; Salvador, F.; Munoz, V.; Salgado, M.

2011-07-01

In this work, as the commissioner of the e-JMRT, a Monte Carlo calculation network for IMRT planning, has developed software for the automatic recording of the image of the film with the results of the planning system.

Estimating software development project size, using probabilistic ...

African Journals Online (AJOL)

Estimating software development project size, using probabilistic techniques. ... of managing the size of software development projects by Purchasers (Clients) and Vendors (Development ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

Hierarchy Software Development Framework (h-dp-fwk) project

International Nuclear Information System (INIS)

Zaytsev, A

2010-01-01

Hierarchy Software Development Framework provides a lightweight tool for building portable modular applications for performing automated data analysis tasks in a batch mode. The history of design and development activities devoted to the project has begun in March 2005 and from the very beginning it was targeting the case of building experimental data processing applications for the CMD-3 experiment which is being commissioned at Budker Institute of Nuclear Physics (BINP, Novosibirsk, Russia). Its design addresses the generic case of modular data processing application operating within the well defined distributed computing environment. The main features of the framework are modularity, built-in message and data exchange mechanisms, XInclude and XML schema enabled XML configuration management tools, dedicated log management tools, internal debugging tools, both dynamic and static module chains support, internal DSO version and consistency checking, well defined API for developing specialized frameworks. It is supported on Scientific Linux 4 and 5 and planned to be ported to other platforms as well. The project is provided with the comprehensive set of technical documentation and users' guides. The licensing schema for the source code, binaries and documentation implies that the product is free for non-commercial use. Although the development phase is not over and many features are to be implemented yet the project is considered ready for public use and creating applications in various fields including development of events reconstruction software for small and moderate scale HEP experiments.

Hierarchy Software Development Framework (h-dp-fwk) project

Energy Technology Data Exchange (ETDEWEB)

Zaytsev, A, E-mail: Alexander.S.Zaytsev@gmail.co [Budker Institute of Nuclear Physics, Novosibirsk (Russian Federation)

2010-04-01

Hierarchy Software Development Framework provides a lightweight tool for building portable modular applications for performing automated data analysis tasks in a batch mode. The history of design and development activities devoted to the project has begun in March 2005 and from the very beginning it was targeting the case of building experimental data processing applications for the CMD-3 experiment which is being commissioned at Budker Institute of Nuclear Physics (BINP, Novosibirsk, Russia). Its design addresses the generic case of modular data processing application operating within the well defined distributed computing environment. The main features of the framework are modularity, built-in message and data exchange mechanisms, XInclude and XML schema enabled XML configuration management tools, dedicated log management tools, internal debugging tools, both dynamic and static module chains support, internal DSO version and consistency checking, well defined API for developing specialized frameworks. It is supported on Scientific Linux 4 and 5 and planned to be ported to other platforms as well. The project is provided with the comprehensive set of technical documentation and users' guides. The licensing schema for the source code, binaries and documentation implies that the product is free for non-commercial use. Although the development phase is not over and many features are to be implemented yet the project is considered ready for public use and creating applications in various fields including development of events reconstruction software for small and moderate scale HEP experiments.

COSINE software development based on code generation technology

International Nuclear Information System (INIS)

Ren Hao; Mo Wentao; Liu Shuo; Zhao Guang

2013-01-01

The code generation technology can significantly improve the quality and productivity of software development and reduce software development risk. At present, the code generator is usually based on UML model-driven technology, which can not satisfy the development demand of nuclear power calculation software. The feature of scientific computing program was analyzed and the FORTRAN code generator (FCG) based on C# was developed in this paper. FCG can generate module variable definition FORTRAN code automatically according to input metadata. FCG also can generate memory allocation interface for dynamic variables as well as data access interface. FCG was applied to the core and system integrated engine for design and analysis (COSINE) software development. The result shows that FCG can greatly improve the development efficiency of nuclear power calculation software, and reduce the defect rate of software development. (authors)

A prospective development study of software-guided radio-frequency ablation of primary and secondary liver tumors: Clinical intervention modelling, planning and proof for ablation cancer treatment (ClinicIMPPACT).

Science.gov (United States)

Reinhardt, Martin; Brandmaier, Philipp; Seider, Daniel; Kolesnik, Marina; Jenniskens, Sjoerd; Sequeiros, Roberto Blanco; Eibisberger, Martin; Voglreiter, Philip; Flanagan, Ronan; Mariappan, Panchatcharam; Busse, Harald; Moche, Michael

2017-12-01

Radio-frequency ablation (RFA) is a promising minimal-invasive treatment option for early liver cancer, however monitoring or predicting the size of the resulting tissue necrosis during the RFA-procedure is a challenging task, potentially resulting in a significant rate of under- or over treatments. Currently there is no reliable lesion size prediction method commercially available. ClinicIMPPACT is designed as multicenter-, prospective-, non-randomized clinical trial to evaluate the accuracy and efficiency of innovative planning and simulation software. 60 patients with early liver cancer will be included at four European clinical institutions and treated with the same RFA system. The preinterventional imaging datasets will be used for computational planning of the RFA treatment. All ablations will be simulated simultaneously to the actual RFA procedure, using the software environment developed in this project. The primary outcome measure is the comparison of the simulated ablation zones with the true lesions shown in follow-up imaging after one month, to assess accuracy of the lesion prediction. This unique multicenter clinical trial aims at the clinical integration of a dedicated software solution to accurately predict lesion size and shape after radiofrequency ablation of liver tumors. Accelerated and optimized workflow integration, and real-time intraoperative image processing, as well as inclusion of patient specific information, e.g. organ perfusion and registration of the real RFA needle position might make the introduced software a powerful tool for interventional radiologists to optimize patient outcomes.

Estimation of total Effort and Effort Elapsed in Each Step of Software Development Using Optimal Bayesian Belief Network

Directory of Open Access Journals (Sweden)

Fatemeh Zare Baghiabad

2017-09-01

Full Text Available Accuracy in estimating the needed effort for software development caused software effort estimation to be a challenging issue. Beside estimation of total effort, determining the effort elapsed in each software development step is very important because any mistakes in enterprise resource planning can lead to project failure. In this paper, a Bayesian belief network was proposed based on effective components and software development process. In this model, the feedback loops are considered between development steps provided that the return rates are different for each project. Different return rates help us determine the percentages of the elapsed effort in each software development step, distinctively. Moreover, the error measurement resulted from optimized effort estimation and the optimal coefficients to modify the model are sought. The results of the comparison between the proposed model and other models showed that the model has the capability to highly accurately estimate the total effort (with the marginal error of about 0.114 and to estimate the effort elapsed in each software development step.

Global Software and IT A Guide to Distributed Development, Projects, and Outsourcing

CERN Document Server

Ebert, Christof

2011-01-01

Global software engineering, implying both internal and outsourced development, is a fast-growing scenario within industry; the growth rates in some sectors are more than 20% per year. However, half of all offshoring activities are cancelled within the first 2 years, at tremendous unanticipated cost to the organization.   This book will provide a more balanced framework for planning global development, covering topics such as managing people in distributed sites, managing a project across locations, mitigating the risk of offshoring, processes for global development, practical outsourcin

Software Testbed for Developing and Evaluating Integrated Autonomous Subsystems

Science.gov (United States)

Ong, James; Remolina, Emilio; Prompt, Axel; Robinson, Peter; Sweet, Adam; Nishikawa, David

2015-01-01

To implement fault tolerant autonomy in future space systems, it will be necessary to integrate planning, adaptive control, and state estimation subsystems. However, integrating these subsystems is difficult, time-consuming, and error-prone. This paper describes Intelliface/ADAPT, a software testbed that helps researchers develop and test alternative strategies for integrating planning, execution, and diagnosis subsystems more quickly and easily. The testbed's architecture, graphical data displays, and implementations of the integrated subsystems support easy plug and play of alternate components to support research and development in fault-tolerant control of autonomous vehicles and operations support systems. Intelliface/ADAPT controls NASA's Advanced Diagnostics and Prognostics Testbed (ADAPT), which comprises batteries, electrical loads (fans, pumps, and lights), relays, circuit breakers, invertors, and sensors. During plan execution, an experimentor can inject faults into the ADAPT testbed by tripping circuit breakers, changing fan speed settings, and closing valves to restrict fluid flow. The diagnostic subsystem, based on NASA's Hybrid Diagnosis Engine (HyDE), detects and isolates these faults to determine the new state of the plant, ADAPT. Intelliface/ADAPT then updates its model of the ADAPT system's resources and determines whether the current plan can be executed using the reduced resources. If not, the planning subsystem generates a new plan that reschedules tasks, reconfigures ADAPT, and reassigns the use of ADAPT resources as needed to work around the fault. The resource model, planning domain model, and planning goals are expressed using NASA's Action Notation Modeling Language (ANML). Parts of the ANML model are generated automatically, and other parts are constructed by hand using the Planning Model Integrated Development Environment, a visual Eclipse-based IDE that accelerates ANML model development. Because native ANML planners are currently

Resource utilization during software development

Science.gov (United States)

Zelkowitz, Marvin V.

1988-01-01

This paper discusses resource utilization over the life cycle of software development and discusses the role that the current 'waterfall' model plays in the actual software life cycle. Software production in the NASA environment was analyzed to measure these differences. The data from 13 different projects were collected by the Software Engineering Laboratory at NASA Goddard Space Flight Center and analyzed for similarities and differences. The results indicate that the waterfall model is not very realistic in practice, and that as technology introduces further perturbations to this model with concepts like executable specifications, rapid prototyping, and wide-spectrum languages, we need to modify our model of this process.

Progress on standardization and automation in software development on W7X

International Nuclear Information System (INIS)

Kühner, Georg; Bluhm, Torsten; Heimann, Peter; Hennig, Christine; Kroiss, Hugo; Krom, Jon; Laqua, Heike; Lewerentz, Marc; Maier, Josef; Schacht, Jörg; Spring, Anett; Werner, Andreas; Zilker, Manfred

2012-01-01

, performance. A further activity is on improving the development cycle. The use of release cycles has already provided favourable concentration of work and predictability of delivery times. However, the demand has risen, to react quickly on priority changes from W7X-project management. So a more agile development cycle is being prepared relying on smaller working packages, shorter release cycles and an associated release plan giving the software development responsible the possibility to react on a shorter time scale.

Progress on standardization and automation in software development on W7X

Energy Technology Data Exchange (ETDEWEB)

Kuehner, Georg, E-mail: kuehner@ipp.mpg.de [Max-Planck-Institut fuer Plasmaphysik, Wendelsteinstrasse 1, D-17491 Greifswald (Germany); Bluhm, Torsten [Max-Planck-Institut fuer Plasmaphysik, Wendelsteinstrasse 1, D-17491 Greifswald (Germany); Heimann, Peter [Max-Planck-Institut fuer Plasmaphysik, Boltzmannstrasse 2, D-85748 Garching (Germany); Hennig, Christine [Max-Planck-Institut fuer Plasmaphysik, Wendelsteinstrasse 1, D-17491 Greifswald (Germany); Kroiss, Hugo [Max-Planck-Institut fuer Plasmaphysik, Boltzmannstrasse 2, D-85748 Garching (Germany); Krom, Jon; Laqua, Heike; Lewerentz, Marc [Max-Planck-Institut fuer Plasmaphysik, Wendelsteinstrasse 1, D-17491 Greifswald (Germany); Maier, Josef [Max-Planck-Institut fuer Plasmaphysik, Boltzmannstrasse 2, D-85748 Garching (Germany); Schacht, Joerg; Spring, Anett; Werner, Andreas [Max-Planck-Institut fuer Plasmaphysik, Wendelsteinstrasse 1, D-17491 Greifswald (Germany); Zilker, Manfred [Max-Planck-Institut fuer Plasmaphysik, Boltzmannstrasse 2, D-85748 Garching (Germany)

2012-12-15

interfaces providing the capability to construct arbitrary function aggregates for dedicated tests of quality attributes as availability, reliability, performance. A further activity is on improving the development cycle. The use of release cycles has already provided favourable concentration of work and predictability of delivery times. However, the demand has risen, to react quickly on priority changes from W7X-project management. So a more agile development cycle is being prepared relying on smaller working packages, shorter release cycles and an associated release plan giving the software development responsible the possibility to react on a shorter time scale.

Newly Developed Software Application for Multiple Access Process Planning

Directory of Open Access Journals (Sweden)

Katarina Monkova

2014-11-01

Full Text Available The purchase of a complex system for computer aided process planning (CAPP can be expensive for little and some middle sized plants, sometimes an inaccessible investment, with a long recoupment period. According to this fact and the author's experience with Eastern European plants, they decided to design a new database application which is suitable for production, stock, and economic data holding as well as processing and exploitation within the manufacturing process. The application can also be used to process a plan according to the selected criteria, for technological documentation and NC program creation. It was based on the theory of a multivariant approach to computer aided plan generation. Its fundamental features, the internal mathematical structure and new code system of processed objects, were prepared by the authors. The verification of the designed information system in real practice has shown that it enables about 30% cost and production time reduction and decreases input material assortment variability.

Testing Software Development Project Productivity Model

Science.gov (United States)

Lipkin, Ilya

Software development is an increasingly influential factor in today's business environment, and a major issue affecting software development is how an organization estimates projects. If the organization underestimates cost, schedule, and quality requirements, the end results will not meet customer needs. On the other hand, if the organization overestimates these criteria, resources that could have been used more profitably will be wasted. There is no accurate model or measure available that can guide an organization in a quest for software development, with existing estimation models often underestimating software development efforts as much as 500 to 600 percent. To address this issue, existing models usually are calibrated using local data with a small sample size, with resulting estimates not offering improved cost analysis. This study presents a conceptual model for accurately estimating software development, based on an extensive literature review and theoretical analysis based on Sociotechnical Systems (STS) theory. The conceptual model serves as a solution to bridge organizational and technological factors and is validated using an empirical dataset provided by the DoD. Practical implications of this study allow for practitioners to concentrate on specific constructs of interest that provide the best value for the least amount of time. This study outlines key contributing constructs that are unique for Software Size E-SLOC, Man-hours Spent, and Quality of the Product, those constructs having the largest contribution to project productivity. This study discusses customer characteristics and provides a framework for a simplified project analysis for source selection evaluation and audit task reviews for the customers and suppliers. Theoretical contributions of this study provide an initial theory-based hypothesized project productivity model that can be used as a generic overall model across several application domains such as IT, Command and Control

CT-Based Brachytherapy Treatment Planning using Monte Carlo Simulation Aided by an Interface Software

Directory of Open Access Journals (Sweden)

Vahid Moslemi

2011-03-01

Full Text Available Introduction: In brachytherapy, radioactive sources are placed close to the tumor, therefore, small changes in their positions can cause large changes in the dose distribution. This emphasizes the need for computerized treatment planning. The usual method for treatment planning of cervix brachytherapy uses conventional radiographs in the Manchester system. Nowadays, because of their advantages in locating the source positions and the surrounding tissues, CT and MRI images are replacing conventional radiographs. In this study, we used CT images in Monte Carlo based dose calculation for brachytherapy treatment planning, using an interface software to create the geometry file required in the MCNP code. The aim of using the interface software is to facilitate and speed up the geometry set-up for simulations based on the patient’s anatomy. This paper examines the feasibility of this method in cervix brachytherapy and assesses its accuracy and speed. Material and Methods: For dosimetric measurements regarding the treatment plan, a pelvic phantom was made from polyethylene in which the treatment applicators could be placed. For simulations using CT images, the phantom was scanned at 120 kVp. Using an interface software written in MATLAB, the CT images were converted into MCNP input file and the simulation was then performed. Results: Using the interface software, preparation time for the simulations of the applicator and surrounding structures was approximately 3 minutes; the corresponding time needed in the conventional MCNP geometry entry being approximately 1 hour. The discrepancy in the simulated and measured doses to point A was 1.7% of the prescribed dose.  The corresponding dose differences between the two methods in rectum and bladder were 3.0% and 3.7% of the prescribed dose, respectively. Comparing the results of simulation using the interface software with those of simulation using the standard MCNP geometry entry showed a less than 1

Factors negatively influencing knowledge sharing in software development

Directory of Open Access Journals (Sweden)

Lucas T. Khoza

2017-07-01

Objective: This study seeks to identify factors that negatively influence knowledge sharing in software development in the developing country context. Method: Expert sampling as a subcategory of purposive sampling was employed to extract information, views and opinions from experts in the field of information and communication technology, more specifically from those who are involved in software development projects. Four Johannesburg-based software developing organisations listed on the Johannesburg Stock Exchange (JSE, South Africa, participated in this research study. Quantitative data were collected using an online questionnaire with closed-ended questions. Results: Findings of this research reveal that job security, motivation, time constraints, physiological factors, communication, resistance to change and rewards are core factors negatively influencing knowledge sharing in software developing organisations. Conclusions: Improved understanding of factors negatively influencing knowledge sharing is expected to assist software developing organisations in closing the gap for software development projects failing to meet the triple constraint of time, cost and scope.

Modernization of software quality assurance

Science.gov (United States)

Bhaumik, Gokul

1988-01-01

The customers satisfaction depends not only on functional performance, it also depends on the quality characteristics of the software products. An examination of this quality aspect of software products will provide a clear, well defined framework for quality assurance functions, which improve the life-cycle activities of software development. Software developers must be aware of the following aspects which have been expressed by many quality experts: quality cannot be added on; the level of quality built into a program is a function of the quality attributes employed during the development process; and finally, quality must be managed. These concepts have guided our development of the following definition for a Software Quality Assurance function: Software Quality Assurance is a formal, planned approach of actions designed to evaluate the degree of an identifiable set of quality attributes present in all software systems and their products. This paper is an explanation of how this definition was developed and how it is used.

Methodology for economic evaluation of software development projects

International Nuclear Information System (INIS)

Witte, D.M.

1990-01-01

Many oil and gas exploration and production companies develop computer software in-house or with contract programmers to support their exploration activities. Software development projects compete for funding with exploration and development projects, though most companies lack valid comparison measures for the two types of projects. This paper presents a methodology of pro form a cash flow analysis for software development proposals intended for internal use. This methodology, based on estimates of development and support costs, exploration benefits, and probability of successful development and implementation, can be used to compare proposed software development projects directly with competing exploration proposals

Technical Note: Development and performance of a software tool for quality assurance of online replanning with a conventional Linac or MR-Linac

Energy Technology Data Exchange (ETDEWEB)

Chen, Guang-Pei, E-mail: gpchen@mcw.edu; Ahunbay, Ergun; Li, X. Allen [Department of Radiation Oncology, Medical College of Wisconsin, Milwaukee, Wisconsin 53226 (United States)

2016-04-15

Purpose: To develop an integrated quality assurance (QA) software tool for online replanning capable of efficiently and automatically checking radiation treatment (RT) planning parameters and gross plan quality, verifying treatment plan data transfer from treatment planning system (TPS) to record and verify (R&V) system, performing a secondary monitor unit (MU) calculation with or without a presence of a magnetic field from MR-Linac, and validating the delivery record consistency with the plan. Methods: The software tool, named ArtQA, was developed to obtain and compare plan and treatment parameters from both the TPS and the R&V system database. The TPS data are accessed via direct file reading and the R&V data are retrieved via open database connectivity and structured query language. Plan quality is evaluated with both the logical consistency of planning parameters and the achieved dose–volume histograms. Beams in between the TPS and R&V system are matched based on geometry configurations. To consider the effect of a 1.5 T transverse magnetic field from MR-Linac in the secondary MU calculation, a method based on modified Clarkson integration algorithm was developed and tested for a series of clinical situations. Results: ArtQA has been used in their clinic and can quickly detect inconsistencies and deviations in the entire RT planning process. With the use of the ArtQA tool, the efficiency for plan check including plan quality, data transfer, and delivery check can be improved by at least 60%. The newly developed independent MU calculation tool for MR-Linac reduces the difference between the plan and calculated MUs by 10%. Conclusions: The software tool ArtQA can be used to perform a comprehensive QA check from planning to delivery with conventional Linac or MR-Linac and is an essential tool for online replanning where the QA check needs to be performed rapidly.

Technical Note: Development and performance of a software tool for quality assurance of online replanning with a conventional Linac or MR-Linac.

Science.gov (United States)

Chen, Guang-Pei; Ahunbay, Ergun; Li, X Allen

2016-04-01

To develop an integrated quality assurance (QA) software tool for online replanning capable of efficiently and automatically checking radiation treatment (RT) planning parameters and gross plan quality, verifying treatment plan data transfer from treatment planning system (TPS) to record and verify (R&V) system, performing a secondary monitor unit (MU) calculation with or without a presence of a magnetic field from MR-Linac, and validating the delivery record consistency with the plan. The software tool, named ArtQA, was developed to obtain and compare plan and treatment parameters from both the TPS and the R&V system database. The TPS data are accessed via direct file reading and the R&V data are retrieved via open database connectivity and structured query language. Plan quality is evaluated with both the logical consistency of planning parameters and the achieved dose-volume histograms. Beams in between the TPS and R&V system are matched based on geometry configurations. To consider the effect of a 1.5 T transverse magnetic field from MR-Linac in the secondary MU calculation, a method based on modified Clarkson integration algorithm was developed and tested for a series of clinical situations. ArtQA has been used in their clinic and can quickly detect inconsistencies and deviations in the entire RT planning process. With the use of the ArtQA tool, the efficiency for plan check including plan quality, data transfer, and delivery check can be improved by at least 60%. The newly developed independent MU calculation tool for MR-Linac reduces the difference between the plan and calculated MUs by 10%. The software tool ArtQA can be used to perform a comprehensive QA check from planning to delivery with conventional Linac or MR-Linac and is an essential tool for online replanning where the QA check needs to be performed rapidly.

Planning the Unplanned Experiment: Assessing the Efficacy of Standards for Safety Critical Software

Science.gov (United States)

Graydon, Patrick J.; Holloway, C. Michael

2015-01-01

We need well-founded means of determining whether software is t for use in safety-critical applications. While software in industries such as aviation has an excellent safety record, the fact that software aws have contributed to deaths illustrates the need for justi ably high con dence in software. It is often argued that software is t for safety-critical use because it conforms to a standard for software in safety-critical systems. But little is known about whether such standards `work.' Reliance upon a standard without knowing whether it works is an experiment; without collecting data to assess the standard, this experiment is unplanned. This paper reports on a workshop intended to explore how standards could practicably be assessed. Planning the Unplanned Experiment: Assessing the Ecacy of Standards for Safety Critical Software (AESSCS) was held on 13 May 2014 in conjunction with the European Dependable Computing Conference (EDCC). We summarize and elaborate on the workshop's discussion of the topic, including both the presented positions and the dialogue that ensued.

The Program for Climate Model Diagnosis and Intercomparison (PCMDI) Software Development: Applications, Infrastructure, and Middleware/Networks

Energy Technology Data Exchange (ETDEWEB)

Williams, Dean N. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2011-06-30

The status of and future plans for the Program for Climate Model Diagnosis and Intercomparison (PCMDI) hinge on software that PCMDI is either currently distributing or plans to distribute to the climate community in the near future. These software products include standard conventions, national and international federated infrastructures, and community analysis and visualization tools. This report also mentions other secondary software not necessarily led by or developed at PCMDI to provide a complete picture of the overarching applications, infrastructures, and middleware/networks. Much of the software described anticipates the use of future technologies envisioned over the span of next year to 10 years. These technologies, together with the software, will be the catalyst required to address extreme-scale data warehousing, scalability issues, and service-level requirements for a diverse set of well-known projects essential for predicting climate change. These tools, unlike the previous static analysis tools of the past, will support the co-existence of many users in a productive, shared virtual environment. This advanced technological world driven by extreme-scale computing and the data it generates will increase scientists’ productivity, exploit national and international relationships, and push research to new levels of understanding.

Usability challenges in an Ethiopian software development organization

DEFF Research Database (Denmark)

Teka, Degif; Dittrich, Yvonne; Kifle, Mesfin

2016-01-01

Usability and user centered design (UCD) are central to software development. In developing countries, the gap between IT development and the local use situation is larger than in western countries. However, usability is neither well addressed in software practice nor at the policy making level...... in Ethiopia. Software practitioners focus on functional requirements, meeting deadlines and budget. The software development industry in Ethiopia is in its early stage. The article aims at understanding usability practices in an Ethiopian software development company. Developers, system analysts, product...... configuration, their experience, cultural knowledge and common sense regarding the users' situation guided the design. Prototypes and fast delivery of working versions helped in getting user feedback even if early user focus proved to be a challenge as communication between developers and users suffered from...

Fundamentals of multicore software development

CERN Document Server

Pankratius, Victor; Tichy, Walter F

2011-01-01

With multicore processors now in every computer, server, and embedded device, the need for cost-effective, reliable parallel software has never been greater. By explaining key aspects of multicore programming, Fundamentals of Multicore Software Development helps software engineers understand parallel programming and master the multicore challenge. Accessible to newcomers to the field, the book captures the state of the art of multicore programming in computer science. It covers the fundamentals of multicore hardware, parallel design patterns, and parallel programming in C++, .NET, and Java. It

Understanding Acceptance of Software Metrics--A Developer Perspective

Science.gov (United States)

Umarji, Medha

2009-01-01

Software metrics are measures of software products and processes. Metrics are widely used by software organizations to help manage projects, improve product quality and increase efficiency of the software development process. However, metrics programs tend to have a high failure rate in organizations, and developer pushback is one of the sources…

Co-sourcing in software development offshoring

DEFF Research Database (Denmark)

Schlichter, Bjarne Rerup; Persson, John Stouby

2013-01-01

Software development projects are increasingly geographical distributed with offshoring, which introduce complex risks that can lead to project failure. Co-sourcing is a highly integrative and cohesive approach, seen successful, to software development offshoring. However, research of how co......-sourcing shapes the perception and alleviation of common offshoring risks is limited. We present a case study of how a certified CMMI-level 5 Danish software supplier approaches these risks in offshore co-sourcing. The paper explains how common offshoring risks are perceived and alleviated when adopting the co...

Software quality concepts and practice

CERN Document Server

Galin, Daniel

2018-01-01

The book presents a comprehensive discussion on software quality issues and software quality assurance (SQA) principles and practices, and lays special emphasis on implementing and managing SQA. Primarily designed to serve three audiences; universities and college students, vocational training participants, and software engineers and software development managers, the book may be applicable to all personnel engaged in a software projects Features: * A broad view of SQA. The book delves into SQA issues, going beyond the classic boundaries of custom-made software development to also cover in-house software development, subcontractors, and readymade software. * An up-to-date wide-range coverage of SQA and SQA related topics. Providing comprehensive coverage on multifarious SQA subjects, including topics, hardly explored till in SQA texts. * A systematic presentation of the SQA function and its tasks: establishing the SQA processes, planning, coordinating, follow-up, review and evaluation of SQA processes. * Fo...

SU-G-TeP4-09: Development of a Plan Data Aggregator for Time Efficient Physics Second-Checks of Machine Parameters for External Beam Treatment Plans

Energy Technology Data Exchange (ETDEWEB)

Belley, M; Schmidt, M; Knutson, N [Rhode Island Hospital, Providence RI (United States); University of Rhode Island, Kingston, RI (United States); Price, M [Rhode Island Hospital, Providence RI (United States); University of Rhode Island, Kingston, RI (United States); Alpert Medical School of Brown University, Providence, RI (United States)

2016-06-15

Purpose: Physics second-checks for external beam radiation therapy are performed, in-part, to verify that the machine parameters in the Record-and-Verify (R&V) system that will ultimately be sent to the LINAC exactly match the values initially calculated by the Treatment Planning System (TPS). While performing the second-check, a large portion of the physicists’ time is spent navigating and arranging display windows to locate and compare the relevant numerical values (MLC position, collimator rotation, field size, MU, etc.). Here, we describe the development of a software tool that guides the physicist by aggregating and succinctly displaying machine parameter data relevant to the physics second-check process. Methods: A data retrieval software tool was developed using Python to aggregate data and generate a list of machine parameters that are commonly verified during the physics second-check process. This software tool imported values from (i) the TPS RT Plan DICOM file and (ii) the MOSAIQ (R&V) Structured Query Language (SQL) database. The machine parameters aggregated for this study included: MLC positions, X&Y jaw positions, collimator rotation, gantry rotation, MU, dose rate, wedges and accessories, cumulative dose, energy, machine name, couch angle, and more. Results: A GUI interface was developed to generate a side-by-side display of the aggregated machine parameter values for each field, and presented to the physicist for direct visual comparison. This software tool was tested for 3D conformal, static IMRT, sliding window IMRT, and VMAT treatment plans. Conclusion: This software tool facilitated the data collection process needed in order for the physicist to conduct a second-check, thus yielding an optimized second-check workflow that was both more user friendly and time-efficient. Utilizing this software tool, the physicist was able to spend less time searching through the TPS PDF plan document and the R&V system and focus the second-check efforts on

Software Engineering Research/Developer Collaborations (C104)

Science.gov (United States)

Shell, Elaine; Shull, Forrest

2005-01-01

The goal of this collaboration was to produce Flight Software Branch (FSB) process standards for software inspections which could be used across three new missions within the FSB. The standard was developed by Dr. Forrest Shull (Fraunhofer Center for Experimental Software Engineering, Maryland) using the Perspective-Based Inspection approach, (PBI research has been funded by SARP) , then tested on a pilot Branch project. Because the short time scale of the collaboration ruled out a quantitative evaluation, it would be decided whether the standard was suitable for roll-out to other Branch projects based on a qualitative measure: whether the standard received high ratings from Branch personnel as to usability and overall satisfaction. The project used for piloting the Perspective-Based Inspection approach was a multi-mission framework designed for reuse. This was a good choice because key representatives from the three new missions would be involved in the inspections. The perspective-based approach was applied to produce inspection procedures tailored for the specific quality needs of the branch. The technical information to do so was largely drawn through a series of interviews with Branch personnel. The framework team used the procedures to review requirements. The inspections were useful for indicating that a restructuring of the requirements document was needed, which led to changes in the development project plan. The standard was sent out to other Branch personnel for review. Branch personnel were very positive. However, important changes were identified because the perspective of Attitude Control System (ACS) developers had not been adequately represented, a result of the specific personnel interviewed. The net result is that with some further work to incorporate the ACS perspective, and in synchrony with the roll out of independent Branch standards, the PBI approach will be implemented in the FSB. Also, the project intends to continue its collaboration with

Modular Infrastructure for Rapid Flight Software Development

Science.gov (United States)

Pires, Craig

2010-01-01

This slide presentation reviews the use of modular infrastructure to assist in the development of flight software. A feature of this program is the use of model based approach for application unique software. A review of two programs that this approach was use on are: the development of software for Hover Test Vehicle (HTV), and Lunar Atmosphere and Dust Environment Experiment (LADEE).

Seismology software: state of the practice

Science.gov (United States)

Smith, W. Spencer; Zeng, Zheng; Carette, Jacques

2018-05-01

We analyzed the state of practice for software development in the seismology domain by comparing 30 software packages on four aspects: product, implementation, design, and process. We found room for improvement in most seismology software packages. The principal areas of concern include a lack of adequate requirements and design specification documents, a lack of test data to assess reliability, a lack of examples to get new users started, and a lack of technological tools to assist with managing the development process. To assist going forward, we provide recommendations for a document-driven development process that includes a problem statement, development plan, requirement specification, verification and validation (V&V) plan, design specification, code, V&V report, and a user manual. We also provide advice on tool use, including issue tracking, version control, code documentation, and testing tools.

Seismology software: state of the practice

Science.gov (United States)

Smith, W. Spencer; Zeng, Zheng; Carette, Jacques

2018-02-01

We analyzed the state of practice for software development in the seismology domain by comparing 30 software packages on four aspects: product, implementation, design, and process. We found room for improvement in most seismology software packages. The principal areas of concern include a lack of adequate requirements and design specification documents, a lack of test data to assess reliability, a lack of examples to get new users started, and a lack of technological tools to assist with managing the development process. To assist going forward, we provide recommendations for a document-driven development process that includes a problem statement, development plan, requirement specification, verification and validation (V&V) plan, design specification, code, V&V report, and a user manual. We also provide advice on tool use, including issue tracking, version control, code documentation, and testing tools.

Agile distributed software development

DEFF Research Database (Denmark)

Persson, John Stouby; Mathiassen, Lars; Aaen, Ivan

2012-01-01

While face-to-face interaction is fundamental in agile software development, distributed environments must rely extensively on mediated interactions. Practicing agile principles in distributed environments therefore poses particular control challenges related to balancing fixed vs. evolving quality...... requirements and people vs. process-based collaboration. To investigate these challenges, we conducted an in-depth case study of a successful agile distributed software project with participants from a Russian firm and a Danish firm. Applying Kirsch’s elements of control framework, we offer an analysis of how...

Development of stand-alone risk assessment software for optimized maintenance planning of power plant facilities

International Nuclear Information System (INIS)

Choi, Woo Sung; Song, Gee Wook; Kim, Bum Shin; Chang, Sung Ho; Lee, Sang Min

2015-01-01

Risk-Risk-based inspection (RBI) has been developed in order to identify risky equipment that can cause major accidents or damages in large-scale plants. This assessment evaluates the equipment's risk, categorizes their priorities based on risk level, and then determines the urgency of their maintenance or allocates maintenance resources. An earlier version of the risk-based assessment software is already installed within the equipment management system; however, the assessment is based on examination by an inspector, and the results can be influenced by his subjective judgment, rather than assessment being based on failure probability. Moreover, the system is housed within a server, which limits the inspector's work space and time, and such a system can be used only on site. In this paper, the development of independent risk-based assessment software is introduced; this software calculates the failure probability by an analytical method, and analyzes the field inspection results, as well as inspection effectiveness. It can also operate on site, since it can be installed on an independent platform, and has the ability to generate an I/O function for the field inspection results regarding the period for an optimum maintenance cycle. This program will provide useful information not only to the field users who are participating in maintenance, but also to the engineers who need to decide whether to extend the life cycle of the power machinery or replace only specific components

Software Engineering Research/Developer Collaborations in 2005

Science.gov (United States)

Pressburger, Tom

2006-01-01

In CY 2005, three collaborations between software engineering technology providers and NASA software development personnel deployed three software engineering technologies on NASA development projects (a different technology on each project). The main purposes were to benefit the projects, infuse the technologies if beneficial into NASA, and give feedback to the technology providers to improve the technologies. Each collaboration project produced a final report. Section 2 of this report summarizes each project, drawing from the final reports and communications with the software developers and technology providers. Section 3 indicates paths to further infusion of the technologies into NASA practice. Section 4 summarizes some technology transfer lessons learned. Also included is an acronym list.

Software process improvement: controlling developers, managers or users?

DEFF Research Database (Denmark)

Nørbjerg, Jacob

1999-01-01

The paper discusses how the latest trend in the management of software development: software process improvement (SPI) may affect user-developer relations. At the outset, SPI concerns the "internal workings" of software organisations, but it may also be interpreted as one way to give the developer...... organisation more control over the development process and the relations with the user organization....

Concept Development for Software Health Management

Science.gov (United States)

Riecks, Jung; Storm, Walter; Hollingsworth, Mark

2011-01-01

This report documents the work performed by Lockheed Martin Aeronautics (LM Aero) under NASA contract NNL06AA08B, delivery order NNL07AB06T. The Concept Development for Software Health Management (CDSHM) program was a NASA funded effort sponsored by the Integrated Vehicle Health Management Project, one of the four pillars of the NASA Aviation Safety Program. The CD-SHM program focused on defining a structured approach to software health management (SHM) through the development of a comprehensive failure taxonomy that is used to characterize the fundamental failure modes of safety-critical software.

Strategies for Developing China's Software Industry

OpenAIRE

Mingzhi Li; Ming Gao

2003-01-01

The software industry is deemed an ideal target for a developing country to integrate into the world information and communications technology (ICT) market. On the one hand the industry is labor intensive, and the developing countries have a large labor surplus; on the other hand, it is a worldwide trend for developed countries to outsource a vast amount of low-end, software-related tasks to the low-cost countries and regions, which fits into some developing countries’ caliber nicely. India h...

Software development an open source approach

CERN Document Server

Tucker, Allen; de Silva, Chamindra

2011-01-01

Overview and Motivation Software Free and Open Source Software (FOSS)Two Case Studies Working with a Project Team Key FOSS Activities Client-Oriented vs. Community-Oriented Projects Working on a Client-Oriented Project Joining a Community-Oriented Project Using Project Tools Collaboration Tools Code Management Tools Run-Time System ConstraintsSoftware Architecture Architectural Patterns Layers, Cohesion, and Coupling Security Concurrency, Race Conditions, and DeadlocksWorking with Code Bad Smells and Metrics Refactoring Testing Debugging Extending the Software for a New ProjectDeveloping the D

CERN software developers gathering in September

CERN Document Server

Antonella Del Rosso

2015-01-01

Hundreds of developers work on many different projects at CERN – from data analysis to beam operations and administrative applications. As of this September, they will have an opportunity to meet each other at the newly established Developers@CERN Forum.   “We go to conferences elsewhere but we hardly ever meet here at CERN, where we all work on our own separate software projects,” says José Carlos Luna, a member of the IT department and one of the organisers of the first Developers@CERN Forum. Indeed, although several CERN departments have software developers working in their teams, there is no proper “community” built around them. The first Developers@CERN Forum will be held on 28 and 29 September. The event is being organised by a few developers from the IT department, together with colleagues from the GS and EN departments. Its main scope is to reach out to all the departments in an effort to bring all CERN’s software dev...

Software Development with DevOps

OpenAIRE

Kristinsson, Rögnvaldur

2015-01-01

The goal of the study was to introduce DevOps in software development, its methods and approaches to software development. I was introduced to the subject by one of my teach-ers, which let me into further studies and researched on the subject and finally choosing it for the study. The subject was completely new to me when I started the study which I found inspirational as I was learning a new and an interesting subject on a daily basis dur-ing the process of writing the study. The materia...

Automated real-time software development

Science.gov (United States)

Jones, Denise R.; Walker, Carrie K.; Turkovich, John J.

1993-01-01

A Computer-Aided Software Engineering (CASE) system has been developed at the Charles Stark Draper Laboratory (CSDL) under the direction of the NASA Langley Research Center. The CSDL CASE tool provides an automated method of generating source code and hard copy documentation from functional application engineering specifications. The goal is to significantly reduce the cost of developing and maintaining real-time scientific and engineering software while increasing system reliability. This paper describes CSDL CASE and discusses demonstrations that used the tool to automatically generate real-time application code.

Agile Software Development: An Introduction and Overview

Science.gov (United States)

Dingsøyr, Torgeir; Dybå, Tore; Moe, Nils Brede

Agile software development is an important topic in software engineering and information systems. This chapter provides a characterization and definition of agile software development, an overview of research through a summary of existing overview studies, an analysis of the research literature so far, and an introduction to the main themes of this book. The first part of the book provides foundations and background of agile development. The second part describes findings from studies of agile methods in practice. The third part identifies principal challenges and discusses new frontiers that agile development methods will meet in the future.

A Conceptual Framework for Lean Regulated Software Development

DEFF Research Database (Denmark)

Cawley, Oisin; Richardson, Ita; Wang, Xiaofeng

2015-01-01

for software development within a regulated environment? This poster presents the results of our empirical research into lean and regulated software development. Built from a combination of data sources, we have developed a conceptual framework comprising five primary components. In addition the relationships...... they have with both the central focus of the framework (the situated software development practices) and with each other are indicated....

Developing a User-Centred Planning Tool for Young Adults with Development Disorders: A Research-Based Teaching Project.

Science.gov (United States)

Ribu, Kirsten; Patel, Tulpesh

2016-01-01

People with development disorders, for instance autism, need structured plans to help create predictability in their daily lives. Digital plans can facilitate enhanced independency, learning, and quality of life, but existing apps are largely general purpose and lack the flexibility required by this specific but heterogeneous user group. Universal design is both a goal and a process and should be based on a holistic approach and user-centered design, interacting with the users in all stages of the development process. At Oslo and Akershus University College (HiOA) we conducted a research-based teaching project in co-operation with the Department of Neuro-habilitation at Oslo University Hospital (OUS) with two employees acting as project managers and students as developers. Three groups of Computer Science bachelor students developed digital prototypes for a planning tool for young adults with pervasive development disorders, who live either with their families or in supervised residences, and do not receive extensive public services. The students conducted the initial planning phase of the software development process, focusing on prototyping the system requirements, whilst a professional software company programmed the end solution. The goal of the project was to develop flexible and adaptive user-oriented and user-specific app solutions for tablets that can aid this diverse user group in structuring daily life, whereby, for example, photos of objects and places known to the individual user replace general pictures or drawings, and checklists can be elaborate or sparse as necessary. The three student groups worked independently of each other and created interactive working prototypes based on tests, observations and short interviews with end users (both administrators and residents) and regular user feedback from the project managers. Three very different solutions were developed that were of high enough quality that an external software company were able to

Global Software Development with Cloud Platforms

Science.gov (United States)

Yara, Pavan; Ramachandran, Ramaseshan; Balasubramanian, Gayathri; Muthuswamy, Karthik; Chandrasekar, Divya

Offshore and outsourced distributed software development models and processes are facing challenges, previously unknown, with respect to computing capacity, bandwidth, storage, security, complexity, reliability, and business uncertainty. Clouds promise to address these challenges by adopting recent advances in virtualization, parallel and distributed systems, utility computing, and software services. In this paper, we envision a cloud-based platform that addresses some of these core problems. We outline a generic cloud architecture, its design and our first implementation results for three cloud forms - a compute cloud, a storage cloud and a cloud-based software service- in the context of global distributed software development (GSD). Our ”compute cloud” provides computational services such as continuous code integration and a compile server farm, ”storage cloud” offers storage (block or file-based) services with an on-line virtual storage service, whereas the on-line virtual labs represent a useful cloud service. We note some of the use cases for clouds in GSD, the lessons learned with our prototypes and identify challenges that must be conquered before realizing the full business benefits. We believe that in the future, software practitioners will focus more on these cloud computing platforms and see clouds as a means to supporting a ecosystem of clients, developers and other key stakeholders.

Usability Evaluation Method for Agile Software Development

Directory of Open Access Journals (Sweden)

Saad Masood Butt

2015-02-01

Full Text Available Agile methods are the best fit for tremendously growing software industry due to its flexible and dynamic nature. But the software developed using agile methods do meet the usability standards? To answer this question we can see that majority of agile software development projects currently involve interactive user interface designs, which can only be possible by following User Centered Design (UCD in agile methods. The question here is, how to integrate UCD with agile models. Both Agile models and UCD are iterative in nature but agile models focus on coding and development of software; whereas, UCD focuses on user interface of the software. Similarly, both of them have testing features where the agile model involves automated tested code while UCD involves an expert or a user to test the user interface. In this paper, a new agile usability model is proposed and the evaluation is of the proposed model is presented by practically implementing it in three real life projects. . Key results from these projects clearly show: the proposed agile model incorporates usability evaluation methods, improves the relationship between usability experts to work with agile software experts; in addition, allows agile developers to incorporate the result from UCD into subsequent interactions.

Co-sourcing in software development offshoring

DEFF Research Database (Denmark)

Schlichter, Bjarne Rerup; Persson, John Stouby

2013-01-01

Software development projects are increasingly geographical distributed with offshoring, which introduce complex risks that can lead to project failure. Co-sourcing is a highly integrative and cohesive approach, seen successful, to software development offshoring. However, research of how co-sour......-taking by high attention to of the closely interrelated structure and technology components in terms of CMMI and the actors’ cohesion and integration in terms of Scrum....

Software Process Improvement Using Force Field Analysis ...

African Journals Online (AJOL)

An improvement plan is then drawn and implemented. This paper studied the state of Nigerian software development organizations based on selected attributes. Force field analysis is used to partition the factors obtained into driving and restraining forces. An attempt was made to improve the software development process ...

Honeywell Modular Automation System Computer Software Documentation

International Nuclear Information System (INIS)

STUBBS, A.M.

2000-01-01

The purpose of this Computer Software Document (CSWD) is to provide configuration control of the Honeywell Modular Automation System (MAS) in use at the Plutonium Finishing Plant (PFP). This CSWD describes hardware and PFP developed software for control of stabilization furnaces. The Honeywell software can generate configuration reports for the developed control software. These reports are described in the following section and are attached as addendum's. This plan applies to PFP Engineering Manager, Thermal Stabilization Cognizant Engineers, and the Shift Technical Advisors responsible for the Honeywell MAS software/hardware and administration of the Honeywell System

Crisis management for software development and knowledge transfer

CERN Document Server

Zykov, Sergey V

2016-01-01

This well structured book discusses lifecycle optimization of software projects for crisis management by means of software engineering methods and tools. Its outcomes are based on lessons learned from the software engineering crisis which started in the 1960s. The book presents a systematic approach to overcome the crisis in software engineering depends which not only depends on technology-related but also on human-related factors. It proposes an adaptive methodology for software product development, which optimizes the software product lifecycle in order to avoid “local” crises of software production. The general lifecycle pattern and its stages are discussed, and their impact on the time and budget of the software product development is analyzed. The book identifies key advantages and disadvantages for various models selected and concludes that there is no “silver bullet”, or universal model, which suits all software products equally well. It approaches software architecture in terms of process, dat...

The MINERVA Software Development Process

Science.gov (United States)

Narkawicz, Anthony; Munoz, Cesar A.; Dutle, Aaron M.

2017-01-01

This paper presents a software development process for safety-critical software components of cyber-physical systems. The process is called MINERVA, which stands for Mirrored Implementation Numerically Evaluated against Rigorously Verified Algorithms. The process relies on formal methods for rigorously validating code against its requirements. The software development process uses: (1) a formal specification language for describing the algorithms and their functional requirements, (2) an interactive theorem prover for formally verifying the correctness of the algorithms, (3) test cases that stress the code, and (4) numerical evaluation on these test cases of both the algorithm specifications and their implementations in code. The MINERVA process is illustrated in this paper with an application to geo-containment algorithms for unmanned aircraft systems. These algorithms ensure that the position of an aircraft never leaves a predetermined polygon region and provide recovery maneuvers when the region is inadvertently exited.

An empirical evaluation of software quality assurance practices and challenges in a developing country: a comparison of Nigeria and Turkey.

Science.gov (United States)

Sowunmi, Olaperi Yeside; Misra, Sanjay; Fernandez-Sanz, Luis; Crawford, Broderick; Soto, Ricardo

2016-01-01

The importance of quality assurance in the software development process cannot be overemphasized because its adoption results in high reliability and easy maintenance of the software system and other software products. Software quality assurance includes different activities such as quality control, quality management, quality standards, quality planning, process standardization and improvement amongst others. The aim of this work is to further investigate the software quality assurance practices of practitioners in Nigeria. While our previous work covered areas on quality planning, adherence to standardized processes and the inherent challenges, this work has been extended to include quality control, software process improvement and international quality standard organization membership. It also makes comparison based on a similar study carried out in Turkey. The goal is to generate more robust findings that can properly support decision making by the software community. The qualitative research approach, specifically, the use of questionnaire research instruments was applied to acquire data from software practitioners. In addition to the previous results, it was observed that quality assurance practices are quite neglected and this can be the cause of low patronage. Moreover, software practitioners are neither aware of international standards organizations or the required process improvement techniques; as such their claimed standards are not aligned to those of accredited bodies, and are only limited to their local experience and knowledge, which makes it questionable. The comparison with Turkey also yielded similar findings, making the results typical of developing countries. The research instrument used was tested for internal consistency using the Cronbach's alpha, and it was proved reliable. For the software industry in developing countries to grow strong and be a viable source of external revenue, software assurance practices have to be taken seriously

BISON Software V&V Plan

Energy Technology Data Exchange (ETDEWEB)

R. L. Williamson; J. D. Hales; D. M. Perez; S. R. Novascone; G. Pastore

2014-07-01

The primary vision for the BISON development team is to deliver a nuclear fuel performance simulation tool that is used to provide a researcher or fuel designer with best estimate calculations of the highly coupled and nonlinear phenomena that govern nuclear fuel behavior. Accurately simulating nuclear fuel behavior is a challenging computational undertaking and verification and validation (V&V) play an important role in realizing this vision. The purpose of this V&V plan is to express the BISON team’s definition of the terms verification and validation, document what we have done regarding V&V, and outline what we plan to do.

Effective Software Engineering Leadership for Development Programs

Science.gov (United States)

Cagle West, Marsha

2010-01-01

Software is a critical component of systems ranging from simple consumer appliances to complex health, nuclear, and flight control systems. The development of quality, reliable, and effective software solutions requires the incorporation of effective software engineering processes and leadership. Processes, approaches, and methodologies for…

Software Development using Object-First Approach: a New Learning Strategy

Directory of Open Access Journals (Sweden)

Gurdeep S Hura

2017-08-01

Full Text Available Software Engineering approach deals with the Software Development (SD that is aligned with design and development of software applications. The Software Development may be implemented in a variety of techniques but its implementation using a procedural paradigm and an imperative language seem to be more effective and efficient for the design and implementation of software applications. The procedural approach for Software Development offers advantages as this it may be used to teach some basic features of programming languages. The object of this paper is to introduce the software development and associated object-first approach for the design of software project application using top-down method. This approach defines functions and modules as basic units for the design and implementation and also for offering hands-on experiences with the basics of programming languages of sequences, selections, iterations structures. These structures will be used to define various modules with programming language constructs for of software development process. The software Development process is one of the very crucial processes of software engineering.

The Effects of Development Team Skill on Software Product Quality

Science.gov (United States)

Beaver, Justin M.; Schiavone, Guy A.

2006-01-01

This paper provides an analysis of the effect of the skill/experience of the software development team on the quality of the final software product. A method for the assessment of software development team skill and experience is proposed, and was derived from a workforce management tool currently in use by the National Aeronautics and Space Administration. Using data from 26 smallscale software development projects, the team skill measures are correlated to 5 software product quality metrics from the ISO/IEC 9126 Software Engineering Product Quality standard. in the analysis of the results, development team skill is found to be a significant factor in the adequacy of the design and implementation. In addition, the results imply that inexperienced software developers are tasked with responsibilities ill-suited to their skill level, and thus have a significant adverse effect on the quality of the software product. Keywords: software quality, development skill, software metrics

Overview of Hazard Assessment and Emergency Planning Software of Use to RN First Responders

Energy Technology Data Exchange (ETDEWEB)

Waller, E; Millage, K; Blakely, W F; Ross, J A; Mercier, J R; Sandgren, D J; Levine, I H; Dickerson, W E; Nemhauser, J B; Nasstrom, J S; Sugiyama, G; Homann, S; Buddemeier, B R; Curling, C A; Disraelly, D S

2008-08-26

There are numerous software tools available for field deployment, reach-back, training and planning use in the event of a radiological or nuclear (RN) terrorist event. Specialized software tools used by CBRNe responders can increase information available and the speed and accuracy of the response, thereby ensuring that radiation doses to responders, receivers, and the general public are kept as low as reasonably achievable. Software designed to provide health care providers with assistance in selecting appropriate countermeasures or therapeutic interventions in a timely fashion can improve the potential for positive patient outcome. This paper reviews various software applications of relevance to radiological and nuclear (RN) events that are currently in use by first responders, emergency planners, medical receivers, and criminal investigators.

Exploring the Role of Social Software in Global Software Development Projects

DEFF Research Database (Denmark)

Giuffrida, Rosalba; Dittrich, Y.

2011-01-01

We present a PhD project that investigates the use of Social Software (SoSo) in Global Software Development (GSD) teams. Since SoSo in unstructured and informal in its own nature, we explore how informal communication, which is challenging in GSD, is supported by SoSo in distributed teams and how...

Communication Planning.

Science.gov (United States)

Development Communication Report, 1978

1978-01-01

Communication planning in developing countries is discussed in individual articles on theory, knowledge production and utilization, planning at the regional level, software, and rural development. A nutrition education project and three experiments in developing educational materials with feedback from villagers in Africa are described in the…

Gamification in Software Development Projects

Directory of Open Access Journals (Sweden)

Platonova Valērija

2017-12-01

Full Text Available Gamification is one of the many ways to motivate employees and introduce more fun in daily activities. The aim of the paper is to analyse the impact of gamification method on the software development projects. The paper contains results of a literature review about application areas of gamification, methods, positive and negative effects on projects. The paper also presents an overview of the gamification tools used in software development projects and attempts to answer the question about benefits of gamification usage: whether gamification in the project leads to the desired results and increases the employee productivity and motivation.

The Social Dynamics of Software Development

NARCIS (Netherlands)

Heiskanen, A.; Newman, M.; Simila, J.

2000-01-01

A variety of experiences in software development processes between a public sector organisation and several software vendors over a decade-long period are described and interpreted. Three information systems histories are presented as case examples and their analysis is based on detailed insider

Development of a fatigue analysis software system

International Nuclear Information System (INIS)

Choi, B. I.; Lee, H. J.; Han, S. W.; Kim, J. Y.; Hwang, K. H.; Kang, J. Y.

2001-01-01

A general purpose fatigue analysis software to predict fatigue lives of mechanical components and structures was developed. This software has some characteristic features including functions of searching weak regions on the free surface in order to reduce computing time significantly, a database of fatigue properties for various materials, and an expert system which can assist any users to get more proper results. This software can be used in the environment consists of commercial finite element packages. Using the software developed fatigue analyses for a SAE keyhole specimen and an automobile knuckle were carried out. It was observed that the results were agree well with those from commercial packages

Significance of preoperative planning software for puncture and channel establishment in percutaneous endoscopic lumbar DISCECTOMY: A study of 40 cases.

Science.gov (United States)

Hu, Zhouyang; Li, Xinhua; Cui, Jian; He, Xiaobo; Li, Cong; Han, Yingchao; Pan, Jie; Yang, Mingjie; Tan, Jun; Li, Lijun

2017-05-01

Preoperative planning software has been widely used in many other minimally invasive surgeries, but there is a lack of information describing the clinical benefits of existing software applied in percutaneous endoscopic lumbar discectomy (PELD). This study aimed to compare the clinical efficacy of preoperative planning software in puncture and channel establishment of PELD with routine methods in treating lumbar disc herniation (LDH). From June 2016 to October 2016, 40 patients who had single L4/5 or L5/S1 disc herniation were divided into two groups. Group A adopted planning software for preoperative puncture simulation while Group B took routine cases discussion for making puncture plans. The channel establishment time, operative time, fluoroscopic times and complications were compared between the two groups. The surgical efficacy was evaluated according to the Visual Analogue Scale (VAS), Oswestry Disability Index (ODI) and modified Macnab's criteria. The mean channel establishment time was 25.1 ± 4.2 min and 34.6 ± 5.4 min in Group A and B, respectively (P  0.05). The findings of modified Macnab's criteria at each follow-up also showed no significant differences (P > 0.05). The application of preoperative planning software in puncture and cannula insertion planning in PELD was easy and reliable, and could reduce the channel establishment time, operative time and fluoroscopic times of PELD significantly. Copyright © 2017 IJS Publishing Group Ltd. Published by Elsevier Ltd. All rights reserved.

OpenADR Open Source Toolkit: Developing Open Source Software for the Smart Grid

Energy Technology Data Exchange (ETDEWEB)

McParland, Charles

2011-02-01

Demand response (DR) is becoming an increasingly important part of power grid planning and operation. The advent of the Smart Grid, which mandates its use, further motivates selection and development of suitable software protocols to enable DR functionality. The OpenADR protocol has been developed and is being standardized to serve this goal. We believe that the development of a distributable, open source implementation of OpenADR will benefit this effort and motivate critical evaluation of its capabilities, by the wider community, for providing wide-scale DR services

Software Quality Assurance Metrics

Science.gov (United States)

McRae, Kalindra A.

2004-01-01

Software Quality Assurance (SQA) is a planned and systematic set of activities that ensures conformance of software life cycle processes and products conform to requirements, standards and procedures. In software development, software quality means meeting requirements and a degree of excellence and refinement of a project or product. Software Quality is a set of attributes of a software product by which its quality is described and evaluated. The set of attributes includes functionality, reliability, usability, efficiency, maintainability, and portability. Software Metrics help us understand the technical process that is used to develop a product. The process is measured to improve it and the product is measured to increase quality throughout the life cycle of software. Software Metrics are measurements of the quality of software. Software is measured to indicate the quality of the product, to assess the productivity of the people who produce the product, to assess the benefits derived from new software engineering methods and tools, to form a baseline for estimation, and to help justify requests for new tools or additional training. Any part of the software development can be measured. If Software Metrics are implemented in software development, it can save time, money, and allow the organization to identify the caused of defects which have the greatest effect on software development. The summer of 2004, I worked with Cynthia Calhoun and Frank Robinson in the Software Assurance/Risk Management department. My task was to research and collect, compile, and analyze SQA Metrics that have been used in other projects that are not currently being used by the SA team and report them to the Software Assurance team to see if any metrics can be implemented in their software assurance life cycle process.

Quality Assurance in Software Development: An Exploratory Investigation in Software Project Failures and Business Performance

Science.gov (United States)

Ichu, Emmanuel A.

2010-01-01

Software quality is perhaps one of the most sought-after attributes in product development, however; this goal is unattained. Problem factors in software development and how these have affected the maintainability of the delivered software systems requires a thorough investigation. It was, therefore, very important to understand software…

Development of E-learning Software Based Multiplatform Components

OpenAIRE

Salamah, Irma; Ganiardi, M. Aris

2017-01-01

E-learning software is a product of information and communication technology used to help dynamic and flexible learning process between teacher and student. The software technology was first used in the development of e-learning software in the form of web applications. The advantages of this technology because of the ease in the development, installation, and distribution of data. Along with advances in mobile/wireless electronics technology, e-learning software is adapted to this technology...

Software Development Management: Empirical and Analytical Perspectives

Science.gov (United States)

Kang, Keumseok

2011-01-01

Managing software development is a very complex activity because it must deal with people, organizations, technologies, and business processes. My dissertation consists of three studies that examine software development management from various perspectives. The first study empirically investigates the impacts of prior experience with similar…

Automating Software Development Process using Fuzzy Logic

NARCIS (Netherlands)

Marcelloni, Francesco; Aksit, Mehmet; Damiani, Ernesto; Jain, Lakhmi C.; Madravio, Mauro

2004-01-01

In this chapter, we aim to highlight how fuzzy logic can be a valid expressive tool to manage the software development process. We characterize a software development method in terms of two major components: artifact types and methodological rules. Classes, attributes, operations, and inheritance

Software engineering

CERN Document Server

Sommerville, Ian

2016-01-01

For courses in computer science and software engineering The Fundamental Practice of Software Engineering Software Engineering introduces readers to the overwhelmingly important subject of software programming and development. In the past few years, computer systems have come to dominate not just our technological growth, but the foundations of our world's major industries. This text seeks to lay out the fundamental concepts of this huge and continually growing subject area in a clear and comprehensive manner. The Tenth Edition contains new information that highlights various technological updates of recent years, providing readers with highly relevant and current information. Sommerville's experience in system dependability and systems engineering guides the text through a traditional plan-based approach that incorporates some novel agile methods. The text strives to teach the innovators of tomorrow how to create software that will make our world a better, safer, and more advanced place to live.

Process mining software repositories: do developers work as expected?

NARCIS (Netherlands)

Poncin, W.; Serebrenik, A.; Brand, van den M.G.J.

2012-01-01

Modern software development commonly makes use of a multitude of software repositories. How can these help us to understand the on-going development process? Researchers of Eindhoven University of Technology design new methods revealing how software has been developed.

Management Guidelines for Database Developers' Teams in Software Development Projects

Science.gov (United States)

Rusu, Lazar; Lin, Yifeng; Hodosi, Georg

Worldwide job market for database developers (DBDs) is continually increasing in last several years. In some companies, DBDs are organized as a special team (DBDs team) to support other projects and roles. As a new role, the DBDs team is facing a major problem that there are not any management guidelines for them. The team manager does not know which kinds of tasks should be assigned to this team and what practices should be used during DBDs work. Therefore in this paper we have developed a set of management guidelines, which includes 8 fundamental tasks and 17 practices from software development process, by using two methodologies Capability Maturity Model (CMM) and agile software development in particular Scrum in order to improve the DBDs team work. Moreover the management guidelines developed here has been complemented with practices from authors' experience in this area and has been evaluated in the case of a software company. The management guidelines for DBD teams presented in this paper could be very usefully for other companies too that are using a DBDs team and could contribute towards an increase of the efficiency of these teams in their work on software development projects.

Path Planning Software and Graphics Interface for an Autonomous Vehicle, Accounting for Terrain Features

National Research Council Canada - National Science Library

Hurezeanu, Vlad

2000-01-01

.... This vehicle performs tasks to include surveying fields, laying mines, and teleoperation. The capability of the vehicle will be increased if its supporting software plans paths that take into account the terrain features...

Object-Oriented Software Development Environments

DEFF Research Database (Denmark)

The book "Object-Oriented Environments - The Mjølner Approach" presents the collective results of the Mjølner Project. The project was set up to work on the widely recognized problems of developing, maintaining and understanding large software systems. The starting point was to use object...... and realizations User interfaces for environments and realizations Grammar-based software architectures Structure-based editing Language implementation, runtime organization, garbage collection Incremental compilation techniques...

The Relevance of Software Development Education for Students

Science.gov (United States)

Liebenberg, Janet; Huisman, Magda; Mentz, Elsa

2015-01-01

Despite a widely-acknowledged shortage of software developers, and reports of a gap between industry needs and software education, the possible gap between students' needs and software development education has not been explored in detail. In their university education, students want to take courses and carry out projects that clearly relate to…

Process for planning and control of software projects using XedroGESPRO

OpenAIRE

Jacqueline Marín-Sánchez; José Alejandro Lugo-García; Pedro Yobanis Piñero-Pérez; Alena María Santiesteban-García; Félix Noel Abelardo-Santana; Javier Menéndez-Rizo

2014-01-01

The software project management in Cuba has become a key area for improving production processes and decisionmaking in organizations. Several models and standards for process improvement, related with project management, proposed best practices on issues of planning and control of projects. However, they are generic guidelines that describe only those activities to execute, leaving the responsibility for implementing to organizations, using sometimes , expensive proprietary infor...

Comparison of 3D reconstruction of mandible for pre-operative planning using commercial and open-source software

Science.gov (United States)

Abdullah, Johari Yap; Omar, Marzuki; Pritam, Helmi Mohd Hadi; Husein, Adam; Rajion, Zainul Ahmad

2016-12-01

3D printing of mandible is important for pre-operative planning, diagnostic purposes, as well as for education and training. Currently, the processing of CT data is routinely performed with commercial software which increases the cost of operation and patient management for a small clinical setting. Usage of open-source software as an alternative to commercial software for 3D reconstruction of the mandible from CT data is scarce. The aim of this study is to compare two methods of 3D reconstruction of the mandible using commercial Materialise Mimics software and open-source Medical Imaging Interaction Toolkit (MITK) software. Head CT images with a slice thickness of 1 mm and a matrix of 512x512 pixels each were retrieved from the server located at the Radiology Department of Hospital Universiti Sains Malaysia. The CT data were analysed and the 3D models of mandible were reconstructed using both commercial Materialise Mimics and open-source MITK software. Both virtual 3D models were saved in STL format and exported to 3matic and MeshLab software for morphometric and image analyses. Both models were compared using Wilcoxon Signed Rank Test and Hausdorff Distance. No significant differences were obtained between the 3D models of the mandible produced using Mimics and MITK software. The 3D model of the mandible produced using MITK open-source software is comparable to the commercial MIMICS software. Therefore, open-source software could be used in clinical setting for pre-operative planning to minimise the operational cost.

Applied software risk management a guide for software project managers

CERN Document Server

Pandian, C Ravindranath

2006-01-01

Few software projects are completed on time, on budget, and to their original specifications. Focusing on what practitioners need to know about risk in the pursuit of delivering software projects, Applied Software Risk Management: A Guide for Software Project Managers covers key components of the risk management process and the software development process, as well as best practices for software risk identification, risk planning, and risk analysis. Written in a clear and concise manner, this resource presents concepts and practical insight into managing risk. It first covers risk-driven project management, risk management processes, risk attributes, risk identification, and risk analysis. The book continues by examining responses to risk, the tracking and modeling of risks, intelligence gathering, and integrated risk management. It concludes with details on drafting and implementing procedures. A diary of a risk manager provides insight in implementing risk management processes.Bringing together concepts ...

Upgrade Software and Computing

CERN Document Server

The LHCb Collaboration, CERN

2018-01-01

This document reports the Research and Development activities that are carried out in the software and computing domains in view of the upgrade of the LHCb experiment. The implementation of a full software trigger implies major changes in the core software framework, in the event data model, and in the reconstruction algorithms. The increase of the data volumes for both real and simulated datasets requires a corresponding scaling of the distributed computing infrastructure. An implementation plan in both domains is presented, together with a risk assessment analysis.

Business Analysis Skills and Techniques Among Software Developers from Various BPO Industries In Iloilo City, Philippines

Directory of Open Access Journals (Sweden)

Alex Ledonio

2016-11-01

Full Text Available In Iloilo City, Philippines, BPO Industry is booming and an upcoming Megaworld Business District situates a multitude of BPO companies. In this study the software developers of various BPO companies in Iloilo City were evaluated according to their competency on Business Analysis Skill and Techniques. A common misconception is that IT programmers should be detached to business analysis process and will just have to wait for the requirement solution to implement through software development. This study will gauge how much skills and knowledge they possess on the Business Analysis side. The result of the study reveals that software developers evaluated has an average rating on Business Analysis Tasks and Techniques. Respondents are lacking skills generally on business planning, business requirements analysis, and elicitation processes. These results can be used as a baseline data to recommend a necessary adjustment in school curricula.

Development of Radio Frequency Antenna Radiation Simulation Software

International Nuclear Information System (INIS)

Mohamad Idris Taib; Rozaimah Abd Rahim; Noor Ezati Shuib; Wan Saffiey Wan Abdullah

2014-01-01

Antennas are widely used national wide for radio frequency propagation especially for communication system. Radio frequency is electromagnetic spectrum from 10 kHz to 300 GHz and non-ionizing. These radiation exposures to human being have radiation hazard risk. This software was under development using LabVIEW for radio frequency exposure calculation. For the first phase of this development, software purposely to calculate possible maximum exposure for quick base station assessment, using prediction methods. This software also can be used for educational purpose. Some results of this software are comparing with commercial IXUS and free ware NEC software. (author)

Teaching Agile Software Development: A Case Study

Science.gov (United States)

Devedzic, V.; Milenkovic, S. R.

2011-01-01

This paper describes the authors' experience of teaching agile software development to students of computer science, software engineering, and other related disciplines, and comments on the implications of this and the lessons learned. It is based on the authors' eight years of experience in teaching agile software methodologies to various groups…

Managing MDO Software Development Projects

Science.gov (United States)

Townsend, J. C.; Salas, A. O.

2002-01-01

Over the past decade, the NASA Langley Research Center developed a series of 'grand challenge' applications demonstrating the use of parallel and distributed computation and multidisciplinary design optimization. All but the last of these applications were focused on the high-speed civil transport vehicle; the final application focused on reusable launch vehicles. Teams of discipline experts developed these multidisciplinary applications by integrating legacy engineering analysis codes. As teams became larger and the application development became more complex with increasing levels of fidelity and numbers of disciplines, the need for applying software engineering practices became evident. This paper briefly introduces the application projects and then describes the approaches taken in project management and software engineering for each project; lessons learned are highlighted.

Software development to support decision making in the selection of nursing diagnoses and interventions for children and adolescents.

Science.gov (United States)

Silva, Kenya de Lima; Évora, Yolanda Dora Martinez; Cintra, Camila Santana Justo

2015-01-01

to report the development of a software to support decision-making for the selection of nursing diagnoses and interventions for children and adolescents, based on the nomenclature of nursing diagnoses, outcomes and interventions of a university hospital in Paraiba. a methodological applied study based on software engineering, as proposed by Pressman, developed in three cycles, namely: flow chart construction, development of the navigation interface, and construction of functional expressions and programming development. the software consists of administrative and nursing process screens. The assessment is automatically selected according to age group, the nursing diagnoses are suggested by the system after information is inserted, and can be indicated by the nurse. The interventions for the chosen diagnosis are selected by structuring the care plan. the development of this tool used to document the nursing actions will contribute to decision-making and quality of care.

Corganiser: a web-based software tool for planning time-sensitive sampling of whole rounds during scientific drilling

DEFF Research Database (Denmark)

Marshall, Ian

2014-01-01

with a wide range of core and section configurations and can thus be used in future drilling projects. Corganiser is written in the Python programming language and is implemented both as a graphical web interface and command-line interface. It can be accessed online at http://130.226.247.137/.......Corganiser is a software tool developed to simplify the process of preparing whole-round sampling plans for time-sensitive microbiology and geochemistry sampling during scientific drilling. It was developed during the Integrated Ocean Drilling Program (IODP) Expedition 347, but is designed to work...

Verification and software validation for nuclear instrumentation

International Nuclear Information System (INIS)

Gaytan G, E.; Salgado G, J. R.; De Andrade O, E.; Ramirez G, A.

2014-10-01

In this work is presented a Verification Methodology and Software Validation, to be applied in instruments of nuclear use with associate software. This methodology was developed under the auspices of IAEA, through the regional projects RLA4022 (ARCAL XCIX) and RLA1011 (RLA CXXIII), led by Mexico. In the first project three plans and three procedures were elaborated taking into consideration IEEE standards, and in the second project these documents were updated considering ISO and IEC standards. The developed methodology has been distributed to the participant countries of Latin America in the ARCAL projects and two related courses have been imparted with the participation of several countries, and participating institutions of Mexico like Instituto Nacional de Investigaciones Nucleares (ININ), Comision Federal de Electricidad (CFE) and Comision Nacional de Seguridad Nuclear y Salvaguardias (CNSNS). In the ININ due to the necessity to work with Software Quality Guarantee in systems for the nuclear power plant of the CFE, a Software Quality Guarantee Plan and five procedures were developed in the year 2004, obtaining the qualification of the ININ for software development for the nuclear power plant of CFE. These first documents were developed taking like reference IEEE standards and regulator guides of NRC, being the first step for the development of the methodology. (Author)

arXiv HEP Software Foundation Community White Paper Working Group - Software Development, Deployment and Validation

CERN Document Server

Couturier, Benjamin; Grasland, Hadrien; Hegner, Benedikt; Jouvin, Michel; Kane, Meghan; Katz, Daniel S.; Kuhr, Thomas; Lange, David; Mendez Lorenzo, Patricia; Ritter, Martin; Stewart, Graeme Andrew; Valassi, Andrea

The High Energy Phyiscs community has developed and needs to maintain many tens of millions of lines of code and to integrate effectively the work of thousands of developers across large collaborations. Software needs to be built, validated, and deployed across hundreds of sites. Software also has a lifetime of many years, frequently beyond that of the original developer, it must be developed with sustainability in mind. Adequate recognition of software development as a critical task in the HEP community needs to be fostered and an appropriate publication and citation strategy needs to be developed. As part of the HEP Softare Foundation's Community White Paper process a working group on Software Development, Deployment and Validation was formed to examine all of these issues, identify best practice and to formulare recommendations for the next decade. Its report is presented here.

Community development planning

International Nuclear Information System (INIS)

Gray, S.I.

1983-01-01

The focus of this paper will be methods of local community involvement in the community development planning efforts which will be required at the recommended sites. Community development planning will include capital improvement plans, housing plans, zoning changes, business development plans and other community service and fiscal plans required to meet the projected needs of new residents as a result of the repository construction and operation. This paper will present, (1) the need for community planning, (2) methods of responding to community planning needs, (3) current community planning issues to be addressed. 2 references, 1 figure

The IceCube Data Acquisition Software: Lessons Learned during Distributed, Collaborative, Multi-Disciplined Software Development.

Energy Technology Data Exchange (ETDEWEB)

Beattie, Keith S; Beattie, Keith; Day Ph.D., Christopher; Glowacki, Dave; Hanson Ph.D., Kael; Jacobsen Ph.D., John; McParland, Charles; Patton Ph.D., Simon

2007-09-21

In this experiential paper we report on lessons learned during the development ofthe data acquisition software for the IceCube project - specifically, how to effectively address the unique challenges presented by a distributed, collaborative, multi-institutional, multi-disciplined project such as this. While development progress in software projects is often described solely in terms of technical issues, our experience indicates that non- and quasi-technical interactions play a substantial role in the effectiveness of large software development efforts. These include: selection and management of multiple software development methodologies, the effective useof various collaborative communication tools, project management structure and roles, and the impact and apparent importance of these elements when viewed through the differing perspectives of hardware, software, scientific and project office roles. Even in areas clearly technical in nature, success is still influenced by non-technical issues that can escape close attention. In particular we describe our experiences on software requirements specification, development methodologies and communication tools. We make observations on what tools and techniques have and have not been effective in this geographically disperse (including the South Pole) collaboration and offer suggestions on how similarly structured future projects may build upon our experiences.

Ethics in computer software design and development

Science.gov (United States)

Alan J. Thomson; Daniel L. Schmoldt

2001-01-01

Over the past 20 years, computer software has become integral and commonplace for operational and management tasks throughout agricultural and natural resource disciplines. During this software infusion, however, little thought has been afforded human impacts, both good and bad. This paper examines current ethical issues of software system design and development in...

A Study On Traditional And Evolutionary Software Development Models

Directory of Open Access Journals (Sweden)

Kamran Rasheed

2017-07-01

Full Text Available Today Computing technologies are becoming the pioneers of the organizations and helpful in individual functionality i.e. added to computing device we need to add softwares. Set of instruction or computer program is known as software. The development of software is done through some traditional or some new or evolutionary models. Software development is becoming a key and a successful business nowadays. Without software all hardware is useless. Some collective steps that are performed in the development of these are known as Software development life cycle SDLC. There are some adaptive and predictive models for developing software. Predictive mean already known like WATERFALL Spiral Prototype and V-shaped models while Adaptive model include agile Scrum. All methodologies of both adaptive and predictive have their own procedure and steps. Predictive are Static and Adaptive are dynamic mean change cannot be made to the predictive while adaptive have the capability of changing. The purpose of this study is to get familiar with all these and discuss their uses and steps of development. This discussion will be helpful in deciding which model they should use in which circumstance and what are the development step including in each model.

Verification and validation process for the safety software in KNICS

International Nuclear Information System (INIS)

Kwon, Kee-Choon; Lee, Jang-Soo; Kim, Jang-Yeol

2004-01-01

This paper describes the Verification and Validation (V and V ) process for safety software of Programmable Logic Controller (PLC), Digital Reactor Protection System (DRPS), and Engineered Safety Feature-Component Control System (ESF-CCS) that are being developed in Korea Nuclear Instrumentation and Control System (KNICS) projects. Specifically, it presents DRPS V and V experience according to the software development life cycle. The main activities of DRPS V and V process are preparation of software planning documentation, verification of Software Requirement Specification (SRS), Software Design Specification (SDS) and codes, and testing of the integrated software and the integrated system. In addition, they include software safety analysis and software configuration management. SRS V and V of DRPS are technical evaluation, licensing suitability evaluation, inspection and traceability analysis, formal verification, preparing integrated system test plan, software safety analysis, and software configuration management. Also, SDS V and V of RPS are technical evaluation, licensing suitability evaluation, inspection and traceability analysis, formal verification, preparing integrated software test plan, software safety analysis, and software configuration management. The code V and V of DRPS are traceability analysis, source code inspection, test case and test procedure generation, software safety analysis, and software configuration management. Testing is the major V and V activity of software integration and system integration phase. Software safety analysis at SRS phase uses Hazard Operability (HAZOP) method, at SDS phase it uses HAZOP and Fault Tree Analysis (FTA), and at implementation phase it uses FTA. Finally, software configuration management is performed using Nu-SCM (Nuclear Software Configuration Management) tool developed by KNICS project. Through these activities, we believe we can achieve the functionality, performance, reliability and safety that are V

Supporting Usability Engineering in Small Software Development Organizations

DEFF Research Database (Denmark)

Bornoe, Nis; Stage, Jan

2013-01-01

Despite an interest and use of different usability engineering methods small software development organizations find it challenging to implement usability engineering into the software development process. We present the results from a study about usability engineering in practice. Through a series...... of semistructured interviews we want to get an understanding of how usability is implemented into the organizations and how it’s practiced in reality. We found that the developers found it problematic to combine agile software development methods with classic usability engineering methods. A lack of solid usability...... engineering expertise and not least experience seems to be a main obstacle for a successful implementation of usability engineering into current software development practices. They are requesting methods and procedures that fit better with their current practices and strategies to implement usability...

Development of a New VLBI Data Analysis Software

Science.gov (United States)

Bolotin, Sergei; Gipson, John M.; MacMillan, Daniel S.

2010-01-01

We present an overview of a new VLBI analysis software under development at NASA GSFC. The new software will replace CALC/SOLVE and many related utility programs. It will have the capabilities of the current system as well as incorporate new models and data analysis techniques. In this paper we give a conceptual overview of the new software. We formulate the main goals of the software. The software should be flexible and modular to implement models and estimation techniques that currently exist or will appear in future. On the other hand it should be reliable and possess production quality for processing standard VLBI sessions. Also, it needs to be capable of processing observations from a fully deployed network of VLBI2010 stations in a reasonable time. We describe the software development process and outline the software architecture.

Towards a New Paradigm of Software Development: an Ambassador Driven Process in Distributed Software Companies

Science.gov (United States)

Kumlander, Deniss

The globalization of companies operations and competitor between software vendors demand improving quality of delivered software and decreasing the overall cost. The same in fact introduce a lot of problem into software development process as produce distributed organization breaking the co-location rule of modern software development methodologies. Here we propose a reformulation of the ambassador position increasing its productivity in order to bridge communication and workflow gap by managing the entire communication process rather than concentrating purely on the communication result.

Development and implementation of a software for assessment of calculations in radiotherapy monitor units

International Nuclear Information System (INIS)

Mueller, Marcio Rogerio; Silva, Marco Antonio da; Rodrigues, Laura Natal

2005-01-01

Objective: To develop and implement a software based on the manual calculation algorithm for verification of the calculations in radiotherapy monitor units and to establish acceptance levels as a mechanism of quality assurance. Materials and methods: Data were obtained from Clinac 600C and 2100C Varian linear accelerators and the computerized treatment planning system used was CadPlan TM . Results: For the 6 MV beams the acceptance levels for deviations among the calculations of monitor units, divided by treatment area, were the following: breast (0.0%±1.7%), head and neck (1.5%±0.5%), hypophysis (-1.7%±0.5%), pelvis (2.1%±2.1%) and thorax (0.2%±1.3%). For the 15 MV beams the suggested level for pelvis in all the treatment techniques was (3.2%±1.3%). Conclusion: The present data are sufficient to justify the use of the software in the clinical practice as a tool for the quality assurance program. (author)

A Design and Development of Multi-Purpose CCD Camera System with Thermoelectric Cooling: Software

Directory of Open Access Journals (Sweden)

S. H. Oh

2007-12-01

Full Text Available We present a software which we developed for the multi-purpose CCD camera. This software can be used on the all 3 types of CCD - KAF-0401E (768×512, KAF-1602E (15367times;1024, KAF-3200E (2184×1472 made in KODAK Co.. For the efficient CCD camera control, the software is operated with two independent processes of the CCD control program and the temperature/shutter operation program. This software is designed to fully automatic operation as well as manually operation under LINUX system, and is controled by LINUX user signal procedure. We plan to use this software for all sky survey system and also night sky monitoring and sky observation. As our results, the read-out time of each CCD are about 15sec, 64sec, 134sec for KAF-0401E, KAF-1602E, KAF-3200E., because these time are limited by the data transmission speed of parallel port. For larger format CCD, the data transmission is required more high speed. we are considering this control software to one using USB port for high speed data transmission.

Space Station: NASA's software development approach increases safety and cost risks. Report to the Chairman, Committee on Science, Space, and Technology, House of Representatives

Science.gov (United States)

1992-06-01

The House Committee on Science, Space, and Technology asked NASA to study software development issues for the space station. How well NASA has implemented key software engineering practices for the station was asked. Specifically, the objectives were to determine: (1) if independent verification and validation techniques are being used to ensure that critical software meets specified requirements and functions; (2) if NASA has incorporated software risk management techniques into program; (3) whether standards are in place that will prescribe a disciplined, uniform approach to software development; and (4) if software support tools will help, as intended, to maximize efficiency in developing and maintaining the software. To meet the objectives, NASA proceeded: (1) reviewing and analyzing software development objectives and strategies contained in NASA conference publications; (2) reviewing and analyzing NASA, other government, and industry guidelines for establishing good software development practices; (3) reviewing and analyzing technical proposals and contracts; (4) reviewing and analyzing software management plans, risk management plans, and program requirements; (4) reviewing and analyzing reports prepared by NASA and contractor officials that identified key issues and challenges facing the program; (5) obtaining expert opinions on what constitutes appropriate independent V-and-V and software risk management activities; (6) interviewing program officials at NASA headquarters in Washington, DC; at the Space Station Program Office in Reston, Virginia; and at the three work package centers; Johnson in Houston, Texas; Marshall in Huntsville, Alabama; and Lewis in Cleveland, Ohio; and (7) interviewing contractor officials doing work for NASA at Johnson and Marshall. The audit work was performed in accordance with generally accepted government auditing standards, between April 1991 and May 1992.

The ALMA Common Software as a Basis for a Distributed Software Development

Science.gov (United States)

Raffi, Gianni; Chiozzi, Gianluca; Glendenning, Brian

The Atacama Large Millimeter Array (ALMA) is a joint project involving astronomical organizations in Europe, North America and Japan. ALMA will consist of 64 12-m antennas operating in the millimetre and sub-millimetre wavelength range, with baselines of more than 10 km. It will be located at an altitude above 5000 m in the Chilean Atacama desert. The ALMA Computing group is a joint group with staff scattered on 3 continents and is responsible for all the control and data flow software related to ALMA, including tools ranging from support of proposal preparation to archive access of automatically created images. Early in the project it was decided that an ALMA Common Software (ACS) would be developed as a way to provide to all partners involved in the development a common software platform. The original assumption was that some key middleware like communication via CORBA and the use of XML and Java would be part of the project. It was intended from the beginning to develop this software in an incremental way based on releases, so that it would then evolve into an essential embedded part of all ALMA software applications. In this way we would build a basic unity and coherence into a system that will have been developed in a distributed fashion. This paper evaluates our progress after 1.5 year of work, following a few tests and preliminary releases. It analyzes the advantages and difficulties of such an ambitious approach, which creates an interface across all the various control and data flow applications.

Workshop on Software Development Tools for Petascale Computing

Energy Technology Data Exchange (ETDEWEB)

Vetter, Jeffrey [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Georgia Inst. of Technology, Atlanta, GA (United States)

2007-08-01

Petascale computing systems will soon be available to the DOE science community. Recent studies in the productivity of HPC platforms point to better software environments as a key enabler to science on these systems. To prepare for the deployment and productive use of these petascale platforms, the DOE science and general HPC community must have the software development tools, such as performance analyzers and debuggers that meet application requirements for scalability, functionality, reliability, and ease of use. In this report, we identify and prioritize the research opportunities in the area of software development tools for high performance computing. To facilitate this effort, DOE hosted a group of 55 leading international experts in this area at the Software Development Tools for PetaScale Computing (SDTPC) Workshop, which was held in Washington, D.C. on August 1 and 2, 2007. Software development tools serve as an important interface between the application teams and the target HPC architectures. Broadly speaking, these roles can be decomposed into three categories: performance tools, correctness tools, and development environments. Accordingly, this SDTPC report has four technical thrusts: performance tools, correctness tools, development environment infrastructures, and scalable tool infrastructures. The last thrust primarily targets tool developers per se, rather than end users. Finally, this report identifies non-technical strategic challenges that impact most tool development. The organizing committee emphasizes that many critical areas are outside the scope of this charter; these important areas include system software, compilers, and I/O.

Towards a Theory of Affect and Software Developers' Performance

OpenAIRE

Graziotin, Daniel

2016-01-01

For more than thirty years, it has been claimed that a way to improve software developers' productivity and software quality is to focus on people. The underlying assumption seems to be that "happy and satisfied software developers perform better". More specifically, affects-emotions and moods-have an impact on cognitive activities and the working performance of individuals. Development tasks are undertaken heavily through cognitive processes, yet software engineering research (SE) lacks theo...