Preparation and Performance Analysis of Na2SO4·10H2O/EG Composite Phase-change Materials

Directory of Open Access Journals (Sweden)

LENG Cong-bin

2017-01-01

Full Text Available Sodium sulfate decahydrate/expanded graphite composite phase-change material (Na2SO4·10H2O/EG was prepared by vacuum adsorption method.The thermal properties of Na2SO4·10H2O/EG,such as melting-solidification,phase separation,supercooling and latent heat were tested and analyzed.The results show that with the addition of 2%(mass fraction borax and 8% EG,the composite phase-change materials Na2SO4·10H2O/EG obtain ideal properties.The phase separation is eliminated,the supercooling degree of Na2SO4·10H2O is reduced from 13.6℃ to below 0.6℃,the latent heat and the energy storage density of the phase-change materials reach 225.77kJ·kg-1 and 218.09MJ·m-3 respectively.The thermal conductivity is also greatly improved.Compared with Na2SO4·10H2O with the addition of the nucleating agent borax only,the time for heat storage is shortened by 52.6%,and the time for heat release is shortened by 55.1%.Even after 500 times of rapid heating and cooling cycles,the performance of Na2SO4·10H2O/EG does not deteriorate.The novel composite phase-change material has better storage/exothermic properties.

The importance of SO{sub 2} and SO{sub 3} for sulphation of gaseous KCl - An experimental investigation in a biomass fired CFB boiler

Energy Technology Data Exchange (ETDEWEB)

Kassman, Haakan [Vattenfall Power Consultant AB, Nykoeping (Sweden); Chalmers University of Technology, Department of Energy and Environment, Division of Energy Technology, Gothenburg (Sweden); Baefver, Linda [Technical Research Institute of Sweden, Energy Technology, Boraas (Sweden); Aamand, Lars-Erik [Chalmers University of Technology, Department of Energy and Environment, Division of Energy Technology, Gothenburg (Sweden)

2010-09-15

This paper is based on results obtained during co-combustion of wood pellets and straw in a 12 MW circulating fluidised bed (CFB) boiler. Elemental sulphur (S) and ammonium sulphate ((NH{sub 4}){sub 2}SO{sub 4}) were used as additives to convert the alkali chlorides (mainly KCl) to less corrosive alkali sulphates. Their performance was then evaluated using several measurement tools including, IACM (on-line measurements of gaseous alkali chlorides), a low-pressure impactor (particle size distribution and chemical composition of extracted fly ash particles), and deposit probes (chemical composition in deposits collected). The importance of the presence of either SO{sub 2} or SO{sub 3} for gas phase sulphation of KCl is also discussed. Ammonium sulphate performed significantly better than elemental sulphur. A more efficient sulphation of gaseous KCl was achieved with (NH{sub 4}){sub 2}SO{sub 4} even when the S/Cl molar ratio was less than half compared to sulphur. Thus the presence of gaseous SO{sub 3} is of greater importance than that of SO{sub 2} for the sulphation of gaseous KCl. (author)

Selective sodium intercalation into sodium nickel-manganese sulfate for dual Na-Li-ion batteries.

Science.gov (United States)

Marinova, Delyana M; Kukeva, Rosica R; Zhecheva, Ekaterina N; Stoyanova, Radostina K

2018-04-26

Double sodium transition metal sulfates combine in themselves unique intercalation properties with eco-compatible compositions - a specific feature that makes them attractive electrode materials for lithium and sodium ion batteries. Herein, we examine the intercalation properties of novel double sodium nickel-manganese sulfate, Na2Ni1/2Mn1/2(SO4)2, having a large monoclinic unit cell, through electrochemical and ex situ diffraction and spectroscopic methods. The sulfate salt Na2Ni1/2Mn1/2(SO4)2 is prepared by thermal dehydration of the corresponding hydrate salt Na2Ni1/2Mn1/2(SO4)2·4H2O having a blödite structure. The intercalation reactions on Na2Ni1-xMnx(SO4)2 are studied in two model cells: half-ion cell versus Li metal anode and full-ion cell versus Li4Ti5O12 anode by using lithium (LiPF6 dissolved in EC/DMC) and sodium electrolytes (NaPF6 dissolved in EC:DEC). Based on ex situ XRD and TEM analysis, it is found that sodium intercalation into Na2Ni1/2Mn1/2(SO4)2 takes place via phase separation into the Ni-rich monoclinic phase and Mn-rich alluaudite phase. The redox reactions involving participation of manganese and titanium ions are monitored by ex situ EPR spectroscopy. It has been demonstrated that manganese ions from the sulfate salt are participating in the electrochemical reaction, while the nickel ions remain intact. As a result, a reversible capacity of about 65 mA h g-1 is reached. The selective intercalation properties determine sodium nickel-manganese sulfate as a new electrode material for hybrid lithium-sodium ion batteries that is thought to combine the advantages of individual lithium and sodium batteries.

3.0 V High Energy Density Symmetric Sodium-Ion Battery: Na4V2(PO4)3∥Na3V2(PO4)3.

Science.gov (United States)

Yao, Xuhui; Zhu, Zixuan; Li, Qi; Wang, Xuanpeng; Xu, Xiaoming; Meng, Jiashen; Ren, Wenhao; Zhang, Xinhe; Huang, Yunhui; Mai, Liqiang

2018-03-28

Symmetric sodium-ion batteries (SIBs) are considered as promising candidates for large-scale energy storage owing to the simplified manufacture and wide abundance of sodium resources. However, most symmetric SIBs suffer from suppressed energy density. Here, a superior congeneric Na 4 V 2 (PO 4 ) 3 anode is synthesized via electrochemical preintercalation, and a high energy density symmetric SIB (Na 3 V 2 (PO 4 ) 3 as a cathode and Na 4 V 2 (PO 4 ) 3 as an anode) based on the deepened redox couple of V 4+ /V 2+ is built for the first time. When measured in half cell, both electrodes show stabilized electrochemical performance (over 3000 cycles). The symmetric SIBs exhibit an output voltage of 3.0 V and a cell-level energy density of 138 W h kg -1 . Furthermore, the sodium storage mechanism under the expanded measurement range of 0.01-3.9 V is disclosed through an in situ X-ray diffraction technique.

The effectiveness of sodium hydroxide (NaOH) and sodium carbonate (Na2CO3) on the impurities removal of saturated salt solution

Science.gov (United States)

Pujiastuti, C.; Ngatilah, Y.; Sumada, K.; Muljani, S.

2018-01-01

Increasing the quality of salt can be done through various methods such as washing (hydro-extraction), re-crystallization, ion exchange methods and others. In the process of salt quality improvement by re-crystallization method where salt product diluted with water to form saturated solution and re-crystallized through heating process. The quality of the salt produced is influenced by the quality of the dissolved salt and the crystallization mechanism applied. In this research is proposed a concept that before the saturated salt solution is recrystallized added a chemical for removal of the impurities such as magnesium ion (Mg), calcium (Ca), potassium (K) and sulfate (SO4) is contained in a saturated salt solution. The chemical reagents that used are sodium hydroxide (NaOH) 2 N and sodium carbonate (Na2CO3) 2 N. This research aims to study effectiveness of sodium hydroxide and sodium carbonate on the impurities removal of magnesium (Mg), calcium (Ca), potassium (K) and sulfate (SO4). The results showed that the addition of sodium hydroxide solution can be decreased the impurity ions of magnesium (Mg) 95.2%, calcium ion (Ca) 45%, while the addition of sodium carbonate solution can decreased magnesium ion (Mg) 66.67% and calcium ion (Ca) 77.5%, but both types of materials are not degradable sulfate ions (SO4). The sodium hydroxide solution more effective to decrease magnesium ion than sodium carbonate solution, and the sodium carbonate solution more effective to decrease calcium ion than sodium hydroxide solution.

Calculation of phase equilibria in the Na2SO4-K2SO4-Cs2SO4-H2O system at 25 deg C

International Nuclear Information System (INIS)

Filippov, V.K.; Kalinkin, A.M.; Vasin, S.K.

1990-01-01

Calculation results of solubility diagram and water activity in saturated solutions of Na 2 SO 4 -K 2 SO 4 -Cs 2 SO 4 -H 2 O system at 25 deg C are presented. It is shown that for the calculation of quaternary systems one can use the Pitzer equations. Solubility diagram for the system studied is plotted and data on composition and water activity of solutions saturated by two or three solid phases are given. Classification of nonvariant equilibria from the viewpoint of isomorphism of solubility and fusibility diagrams permits to depict the direction of phase processes during isothermal evaporation of water

Osmotic and activity coefficients of {y Na2SO4 + (1 - y) ZnSO4}(aq) at T = 298.15 K

International Nuclear Information System (INIS)

Marjanovic, V.; Ninkovic, R.; Miladinovic, J.; Todorovic, M.; Pavicevic, V.

2005-01-01

The osmotic coefficients of the mixed electrolyte solution {y Na 2 SO 4 + (1 - y) ZnSO 4 }(aq) have been measured by the isopiestic method, at T = 298.5 K. The experimental results were treated by Scatchard's, Pitzer-Kim's and Clegg-Pitzer-Brimblecombe's methods for mixed-electrolyte solutions. By these methods, the activity coefficients for Na 2 SO 4 and ZnSO 4 were calculated and compared. The Scatchard interaction parameters are used for calculation of the excess Gibbs free energy as a function of ionic strength and ionic-strength fraction of Na 2 SO 4 . Also, the Zdanovskii's rule of linearity is tested

Thermal expansion of the nuclear fuel-sodium reaction product Na3(U0.84(2),Na0.16(2))O4 - Structural mechanism and comparison with related sodium-metal ternary oxides

Science.gov (United States)

Illy, Marie-Claire; Smith, Anna L.; Wallez, Gilles; Raison, Philippe E.; Caciuffo, Roberto; Konings, Rudy J. M.

2017-07-01

Na3.16(2)UV,VI0.84(2)O4 is obtained from the reaction of sodium with uranium dioxide under oxygen potential conditions typical of a sodium-cooled fast nuclear reactor. In the event of a breach of the steel cladding, it would be the dominant reaction product forming at the rim of the mixed (U,Pu)O2 fuel pellets. High-temperature X-ray diffraction measurements show that a distortion of the uranium environment in Na3.16(2)UV,VI0.84(2)O4 results in a strongly anisotropic thermal expansion. A comparison with several related sodium metallates Nan-2Mn+On-1 - including Na3SbO4 and Na3TaO4, whose crystal structures are reported for the first time - has allowed us to assess the role played in the lattice expansion by the Mn+ cation radius and the Na/M ratio. On this basis, the thermomechanical behavior of the title compound is discussed, along with those of several related double oxides of sodium and actinide elements, surrogate elements, or fission products.

Electrochemical study in the molten sodium acid sulphate - potassium acid sulphate eutectic

International Nuclear Information System (INIS)

Le Ber, F.

1964-01-01

The general properties of the NaHSO 4 - KHSO 4 molten eutectic resemble those of neutral sulphates and those of concentrated H 2 SO 4 . We have been able to show the existence in solution of the ions HSO - 4 SO 2- 4 , and H 3 O + , these last being formed by the action of the HSO - 4 ions on dissolved H 2 O. The electro-active zone with a polished platinum electrode is limited in oxidation by the ions H 3 O + and SO 2- 4 , and in reduction by the protons of HSO - 4 . We have compared the electro-active zones obtained with different electrodes (Ag-Au-graphite-mercury). We have considered the dissolution of a few metallic oxides and halides. This work shows the role as O 2- ion acceptors of HSO - 4 ions. We have undertaken an electro-chemical study of a few oxido-reduction Systems: H + / H 2 , Ag↓ / Ag (1), the vanadium and uranium Systems, those of mercury Hg↓ / Hg 2- 2 and of gold Au/Au 3+ , then of the attack by the solvent of a few common metals such as aluminium, iron, copper and nickel. The study of silver Systems has made it possible to obtain the solubility products of AgCl and AgBr and to consider the possibility of coulometric titration Cl - ions with Ag + ions. We have shown the existence of various chemical species of vanadium which may exist in the molten eutectic. (author) [fr

The ternary system K2SO4MgSO4CaSO4

Science.gov (United States)

Rowe, J.J.; Morey, G.W.; Silber, C.C.

1967-01-01

Melting and subsolidus relations in the system K2SO4MgSO4CaSO4 were studied using heating-cooling curves, differential thermal analysis, optics, X-ray diffraction at room and high temperatures and by quenching techniques. Previous investigators were unable to study the binary MgSO4CaSO4 system and the adjacent area in the ternary system because of the decomposition of MgSO4 and CaSO4 at high temperatures. This problem was partly overcome by a novel sealed-tube quenching method, by hydrothermal synthesis, and by long-time heating in the solidus. As a result of this study, we found: (1) a new compound, CaSO4??3MgSO4 (m.p. 1201??C) with a field extending into the ternary system; (2) a high temperature form of MgSO4 with a sluggishly reversible inversion. An X-ray diffraction pattern for this polymorphic form is given; (3) the inversion of ??-CaSO4 (anhydrite) to ??-CaSO4 at 1195??C, in agreement with grahmann; (1) (4) the melting point of MgSO4 is 1136??C and that of CaSO4 is 1462??C (using sealed tube methods to prevent decomposition of the sulphates); (5) calcium langbeinite (K2SO4??2CaSO4) is the only compound in the K2SO4CaSO4 binary system. This resolved discrepancies in the results of previous investigators; (6) a continuous solid solution series between congruently melting K2SOP4??2MgSO4 (langbeinite) and incongruently melting K2SO4??2CaSO4 (calcium langbeinite); (7) the liquidus in the ternary system consists of primary phase fields of K2SO4, MgSO4, CaSO4, langbeinite-calcium langbeinite solid solution, and CaSO4??3MgSO4. The CaSO4 field extends over a large portion of the system. Previously reported fields for the compounds (K2SO4??MgSO4??nCaSO4), K2SO4??3CaSO4 and K2SO4??CaSO4 were not found; (8) a minimum in the ternary system at: 740??C, 25% MgSO4, 6% CaSO4, 69% K2SO4; and ternary eutectics at 882??C, 49% MgSO4, 19% CaSO4, 32% K2SO4; and 880??, 67??5% MgSO4, 5% CaSO4, 27??5% K2SO4. ?? 1967.

Thermal expansion of the nuclear fuel-sodium reaction product Na{sub 3}(U{sub 0.84(2)},Na{sub 0.16(2)})O{sub 4} - Structural mechanism and comparison with related sodium-metal ternary oxides

Energy Technology Data Exchange (ETDEWEB)

Illy, Marie-Claire [Chimie ParisTech, PSL Research University, CNRS, Institut de Recherche de Chimie Paris (IRCP), F-75005 Paris (France); European Commission, Joint Research Centre, P.O. Box 2340, 76125 Karlsruhe (Germany); Smith, Anna L. [European Commission, Joint Research Centre, P.O. Box 2340, 76125 Karlsruhe (Germany); Delft University of Technology, Faculty of Applied Sciences, Department of Radiation Science & Technology, Nuclear Energy and Radiation Applications (NERA), Mekelweg 15, 2629 JB, Delft (Netherlands); Wallez, Gilles, E-mail: gilles.wallez@upmc.fr [Chimie ParisTech, PSL Research University, CNRS, Institut de Recherche de Chimie Paris (IRCP), F-75005 Paris (France); Sorbonne University, UPMC Université, Paris 06, 75005 Paris (France); Raison, Philippe E.; Caciuffo, Roberto; Konings, Rudy J.M. [European Commission, Joint Research Centre, P.O. Box 2340, 76125 Karlsruhe (Germany)

2017-07-15

Na{sub 3.16(2)}U{sup V,VI}{sub 0.84(2)}O{sub 4} is obtained from the reaction of sodium with uranium dioxide under oxygen potential conditions typical of a sodium-cooled fast nuclear reactor. In the event of a breach of the steel cladding, it would be the dominant reaction product forming at the rim of the mixed (U,Pu)O{sub 2} fuel pellets. High-temperature X-ray diffraction measurements show that a distortion of the uranium environment in Na{sub 3.16(2)}U{sup V,VI}{sub 0.84(2)}O{sub 4} results in a strongly anisotropic thermal expansion. A comparison with several related sodium metallates Na{sub n-2}M{sup n+}O{sub n-1} - including Na{sub 3}SbO{sub 4} and Na{sub 3}TaO{sub 4}, whose crystal structures are reported for the first time - has allowed us to assess the role played in the lattice expansion by the M{sup n+} cation radius and the Na/M ratio. On this basis, the thermomechanical behavior of the title compound is discussed, along with those of several related double oxides of sodium and actinide elements, surrogate elements, or fission products. - Highlights: •Thermal expansion and structural mechanism of Na{sub 3}(U{sub 0.84(2)},Na{sub 0.16(2)})O{sub 4}, main product of the reaction of sodium with nuclear fuel. •Thermomechanical behavior of sodium uranate suggests possible strains on the fuel cladding and risks of de-cohesion with the fuel pin. •Effect of homo- and aliovalent cation substitutions allows to predict the thermomechanical behavior of sodium metallates involving fission products or minor actinide elements. •Crystal structure of new compounds Na{sub 3}SbO{sub 4} and Na{sub 3}TaO{sub 4}.

Growth of sodium chlorate crystals in the presence of potassium sulphate

Science.gov (United States)

Kim, E. L.; Tsyganova, A. A.; Vorontsov, D. A.; Ovsetsina, T. I.; Katkova, M. R.; Lykov, V. A.; Portnov, V. N.

2015-09-01

In this work, we investigated the morphology and growth rates of NaClO3 crystals in solutions with K2SO4 additives. NaClO3 crystals were grown using the temperature gradient technique under concentration convection. We found that the crystal habitus changed from cubic to tetrahedral, and the growth of the cubic {100}, tetrahedral {111} and rhomb-dodecahedral {110} faces decelerated with an increase in the concentration of SO42- ions. The {110} face was the most and the {100} face was the least inhibited by sulphate ions. The mechanism of SO42- ions action is their adsorption on the crystal surface, which impedes attachment of the crystal's building units. We conclude that different atomic structure and charge state of various crystal faces determine their sensitivity to the action of the SO42- ions.

The system NaVO3-Na2WO4-Na2W2O7

International Nuclear Information System (INIS)

Kazanbekov, V.R.; Gasanaliev, A.M.; Kazanbekov, R.G.

1994-01-01

Phase diagrams of sodium metavanadate-sodium ditungstate, sodium metavanadate-sodium tungstate systems and surface of primary crystallization of sodium metavabadate-sodium tungstate-sodium ditungstate system were studied. The system sodium metavanadate-sodium ditungstate is eutectic one. Compound NaVO 3 x2Na 2 WO 4 is formed in solid state in sodium metavanadate-sodium tungstate system. Liquidus surface of sodium metavanadate-sodium tungstate-sodium ditungstate is presented by three crystallization fields of initial components. Composition and melting point of ternary eutectics are determined

Investigation into the dehydration of selenate doped Na2M(SO4)2·2H2O (M = Mn, Fe, Co and Ni): Stabilisation of the high Na content alluaudite phases Na3M1.5(SO4)3-1.5x(SeO4)1.5x (M = Mn, Co and Ni) through selenate incorporation

Science.gov (United States)

Driscoll, L. L.; Kendrick, E.; Knight, K. S.; Wright, A. J.; Slater, P. R.

2018-02-01

In this paper we report an investigation into the phases formed on dehydration of Na2M(SO4)2-x(SeO4)x·2H2O (0 ≤ x ≤ 1; M = Mn, Fe, Co and Ni). For the Fe series, all attempts to dehydrate the samples doped with selenate resulted in amorphous products, and it is suspected that a side redox reaction involving the Fe and selenate may be occurring leading to phase decomposition and hence the lack of a crystalline product on dehydration. For M = Mn, Co, Ni, the structure observed was shown to depend upon the transition metal cation and level of selenate doping. An alluaudite phase, Na3M1.5(SO4)3-1.5x(SeO4)1.5x, was observed for the selenate doped compositions, with this phase forming as a single phase for x ≥ 0.5 M = Co, and x = 1.0 M = Ni. For M = Mn, the alluaudite structure is obtained across the series, albeit with small impurities for lower selenate content samples. Although the alluaudite-type phases Na2+2y(Mn/Co)2-y(SO4)3 have recently been reported [1,2], doping with selenate appears to increase the maximum sodium content within the structure. Moreover, the selenate doped Ni based samples reported here are the first examples of a Ni sulfate/selenate containing system exhibiting the alluaudite structure.

Sulphate solubility and sulphate diffusion in oxide glasses: implications for the containment of sulphate-bearing nuclear wastes

International Nuclear Information System (INIS)

Lenoir, M.

2009-09-01

The thesis deals with sulphate solubility and sulphate diffusion in oxide glasses, in order to control sulphate incorporation and sulphate volatilization in nuclear waste glasses. It was conducted on simplified compositions, in the SiO 2 -B 2 O 3 -R 2 O (R = Li, Na, K, Cs), SiO 2 -B 2 O 3 -BaO and V 2 O 5 -B 2 O 3 -BaO systems. These compositions allowed us to study the influence of the nature of network-modifying ions (Li + , Na + , K + , Cs + or Ba 2+ ) and also of former elements (Si, B, V), on structure and properties of glasses. Sulphate volatility is studied in sodium borosilicate melts using an innovative technique of sulphate quantitation with Raman spectroscopy. This technique is useful to obtain kinetic curves of sulphate volatilization. The establishment of a model to fit these curves leads to the determination of diffusion coefficients of sulphate. These diffusion coefficients can thus be compared to diffusion coefficients of other species, determined by other techniques and presented in the literature. They are also linked to diffusion coefficients in relation with the viscosity of the melts. Concerning sulphate solubility in glasses, it depends on glass composition and on the nature of sulphate incorporated. Sulphate incorporation in alkali borosilicate glasses leads to the formation of a sulphate layer floating on top of the melt. Sulphate incorporation in barium borosilicate and boro-vanadate glasses leads to the crystallization of sulphate species inside the vitreous matrix. Moreover, sulphate solubility is higher in these glasses than in alkali borosilicates. Finally, exchanges between cations present in glasses and cations present in the sulphate phase are also studied. (author)

Osmotic and ionic effects of NaCl and Na₂SO₄ salinity on Phragmites australis

DEFF Research Database (Denmark)

Pagter, Majken; Bragato, Claudia; Malagoli, Mario

2009-01-01

Osmotic and ion-specific effects of NaCl and Na2SO4 on Phragmites australis (Cav.) Trin ex. Steud. were investigated in a laboratory experiment by examining effects of iso-osmotic solutions of NaCl and Na2SO4 on growth, osmolality of cell sap, proline content, elemental composition and gas exchange....... Plants were supplied with a control standard nutrient solution (Ψ = -0.09 MPa) or solutions of NaCl or Na2SO4 at water potentials of -0.50, -1.09 or -1.74 MPa. Salt treatments increased root concentrations of Na and S or Cl, whereas P. australis had efficient mechanisms for exclusion of Na and S...... and partly Cl ions from the leaves. Incomplete exclusion of Cl from the leaves may affect aboveground biomass production, which was significantly more reduced by NaCl than Na2SO4. Stomatal conductance was negatively influenced by decreasing water potentials caused by NaCl or Na2SO4, implying that a non...

Selectivity of crystalline Ce(IV)-phosphate-sulphate hydrates for Li+, Na+, K+, Rb+, Cs+, and NH4+ in aqueous medium

International Nuclear Information System (INIS)

Koenig, K.H.; Psotta, L.

1978-01-01

The sequence of exchange-capacities of Cerium(IV)-phosphate-sulphate hydrate (CePO 4 ) 2 (HPO 4 )sub(0.74)(SO 4 )sub(0.26) . 4.74 H 2 O concerning the alkaline ions and the ammonium ion in water at 25 0 C for the case of a small excess of the exchanger (in relation to the equivalent amount) is given by Na + > K + > Rb + > NH 4 + > Cs + > Li + . The simple relation A const/r was found between the exchange-capacity A of these cations and their ionic radii r (given by Ladd); only for Li + the radius of the inner hydration-shell must be considered. The observations are consistent with Eisenmann's theory. (author)

Effect of Na poisoning catalyst (V2O5-WO3/TiO2) on denitration process and SO3 formation

Science.gov (United States)

Xiao, Haiping; Chen, Yu; Qi, Cong; Ru, Yu

2018-03-01

This paper aims to study the effect of alkali metal sodium (Na) poisoning on the performance of the Selective Catalytic Reduction (SCR) catalyst. The result showed that Na2SO4 poisoning leads to a reduced denitration rate of the SCR catalyst and an increase in the SO3 generation rate. Na2O poisoning leads to a significant reduction in the denitration rate of the SCR catalyst and marginally improves the formation of SO3. The maximum of the SO3 generation rate for a Na2SO4-poisoned catalyst reached 1.35%, whereas it was only 0.85% for the SCR catalyst. When the SO2 was contained in flue gas, the denitration rate for the Na2O-poisoned catalyst clearly increased by more than 28%. However, the effect of SO2 on the Na2SO4-poisoned catalyst was very slight. The denitration rate of the SCR catalyst decreased with an increase in the Na content. The BET and XRD results showed that Na poisoning of the catalyst decreased the number of acid sites, the reducibility of the catalyst, the surface area, and pore volume. The H2-TPR and NH3-TPD results show that Na decreases the number of acid sites and the reducibility of the catalyst. The FT-IR and XPS results showed that Na2O poisoning led to the decrease of V5+dbnd O bonds and the consumptions of oxygen atoms. Na2SO4 poisoning can improve surface adsorbed oxygen, which was beneficial for the SO2-SO3 conversion reaction.

Study of the structure of H₂SO₄-amine Primene 81R and Fe(III-amine Primene 81R sulphate compounds by infrared spectroscopy

Directory of Open Access Journals (Sweden)

Alguacil, F. J.

1999-08-01

Full Text Available The primary amine Primene 81R extracts sulphuric acid from aqueous solutions to form the corresponding sulphate and bisulphate salts. The infrared study shows that in the sulphate salt, the sulphate group presents a T_d symmetry, whereas the amine bisulphate presents a C_3v symmetry for the bisulphate group. The former of the above compounds, the amine sulphate, is complexed to Fe(III in sulphate media, and two complexes are extracted depending on temperature. At 8°C or lower temperatures a complex with the stoichiometric formula 4(RNH₃₂SO₄ (Fe(OHSO₄2 is formed, whereas at 50°C or higher temperatures the complex with the stoichiometric formula 3(RNH₃₂SO₄ (Fe(OHSO₄₂ is formed. The infrared spectrum of both complexes is very similar and it is consistent with a weaker interaction between the protons associated with the amine group and the anion, and with a change in the symmetry of the sulphate group respect to the symmetry presented in the amine sulphate salt.

La amina primaria Primene 81R extrae al ácido sulfúrico de los medios acuosos para formar las sales sulfato y bisulfato. El estudio IR muestra que en la sal sulfato, el grupo sulfato presenta una simetría T_d, mientras que en la sal bisulfato este grupo presenta una simetría C_3v. La sal sulfato compleja al Fe(III, formando dos compuestos en función de la temperatura de reacción. A temperaturas iguales a 8°C o inferiores se forma el compuesto de estequiometría 4(RNH₃₂SO₄ (Fe(OHSO₄₂, mientras que a temperaturas iguales o superiores a 50°C la estequiometría del compuesto extraído es 3(RNH₃₂SO₄ (Fe(OHSO₄₂. El espectro infrarrojo de ambos compuestos es muy parecido y es consistente, tanto con una interacción d

Na2MnSiO4 as an attractive high capacity cathode material for sodium-ion battery

Science.gov (United States)

Law, Markas; Ramar, Vishwanathan; Balaya, Palani

2017-08-01

Here we report a polyanion-based cathode material for sodium-ion batteries, Na2MnSiO4, registering impressive sodium storage performances with discharge capacity of 210 mAh g-1 at an average voltage of 3 V at 0.1 C, along with excellent long-term cycling stability (500 cycles at 1 C). Insertion/extraction of ∼1.5 mol of sodium ion per formula unit of the silicate-based compound is reported and the utilisation of Mn2+ ⇋ Mn4+ redox couple is also demonstrated by ex-situ XPS. Besides, this study involves a systematic investigation of influence of the electrolyte additive (with different content) on the sodium storage performance of Na2MnSiO4. The electrolyte additive forms an optimum protective passivation film on the electrode surface, successfully reducing manganese dissolution.

Mechanism of Na2SO4 Promoting Nickel Extraction from Sulfide Concentrates by Sulfation Roasting-Water Leaching

Science.gov (United States)

Li, Guangshi; Cheng, Hongwei; Chen, Sha; Lu, Xionggang; Xu, Qian; Lu, Changyuan

2018-06-01

As a more environmentally friendly and energy-efficient route, the sulfation roasting-water leaching technique has been developed for highly effective extraction of non-ferrous metals from nickel sulfide concentrate in the presence of a Na2SO4 additive. The effects of several important roasting parameters—the roasting temperature, the addition of Na2SO4, the holding time, and the heating rate in particular—have been investigated. The results suggest that about 90 pct Ni, 92 pct Co, 95 pct Cu, and leached from the calcine roasted under the optimum conditions. Furthermore, the behavior and mechanism of the Na2SO4 additive in the roasting process have been well addressed by detailed characterization of the roasted product and leaching residue using quantitative phase analysis (QPA) and energy dispersive spectroscopy (EDS) mapping. The Na2SO4 additive was observed to play a noticeable role in promoting the sulfation degree of valuable metals by forming liquid phases [Na2Me(SO4)2] at the outermost layer, which can create a suitable dynamic environment for sulfation. Thus, addition of Na2SO4 might be conducive to an alternative metallurgical process involving complex sulfide ores.

Isopiestic Investigation of the Osmotic and Activity Coefficients of {yMgCl2 + (1 - y)MgSO4}(aq) and the Osmotic Coefficients of Na2SO4.MgSO4(aq) at 298.15 K

Energy Technology Data Exchange (ETDEWEB)

Miladinovic, J; Ninkovic, R; Todorovic, M; Rard, J A

2007-06-06

Isopiestic vapor pressure measurements were made for {l_brace}yMgCl{sub 2} + (1-y)MgSO{sub 4}{r_brace}(aq) solutions with MgCl{sub 2} ionic strength fractions of y = 0, 0.1997, 0.3989, 0.5992, 0.8008, and (1) at the temperature 298.15 K, using KCl(aq) as the reference standard. These measurements for the mixtures cover the ionic strength range I = 0.9794 to 9.4318 mol {center_dot} kg{sup -1}. In addition, isopiestic measurements were made with NaCl(aq) as reference standard for mixtures of {l_brace}xNa{sub 2}SO{sub 4} + (1-x)MgSO{sub 4}{r_brace}(aq) with the molality fraction x = 0.50000 that correspond to solutions of the evaporite mineral bloedite (astrakanite), Na{sub 2}Mg(SO{sub 4}){sub 2} {center_dot} 4H{sub 2}O(cr). The total molalities, m{sub T} = m(Na{sub 2}SO{sub 4}) + m(MgSO{sub 4}), range from m{sub T} = 1.4479 to 4.4312 mol {center_dot} kg{sup -1} (I = 5.0677 to 15.509 mol {center_dot} kg{sup -1}), where the uppermost concentration is the highest oversaturation molality that could be achieved by isothermal evaporation of the solvent at 298.15 K. The parameters of an extended ion-interaction (Pitzer) model for MgCl2(aq) at 298.15 K, which were required for an analysis of the {l_brace}yMgCl{sub 2} + (1-y)MgSO{sub 4}{r_brace}(aq) mixture results, were evaluated up to I = 12.025 mol {center_dot} kg{sup -1} from published isopiestic data together with the six new osmotic coefficients obtained in this study. Osmotic coefficients of {l_brace}yMgCl{sub 2} + (1-y)MgSO{sub 4}{r_brace}(aq) solutions from the present study, along with critically-assessed values from previous studies, were used to evaluate the mixing parameters of the extended ion-interaction model.

Chemistry of Frozen NaCl and MgSO4 Brines - Implications for Surface Expression of Europa's Ocean Composition

Science.gov (United States)

Johnson, P. V.; Hodyss, R. P.; Choukroun, M.; Vu, T. H.

2015-12-01

The composition of Europa's subsurface ocean is a critical determinant of its habitability, but current analysis of the ocean composition is limited to its expression on the Europan surface. While there is observational evidence indicating that ocean materials make their way to the surface, our understanding of the chemical processes that can alter this material under Europan surface conditions is limited. We present experimental data on the chemistry of mixed solutions of NaCl and MgSO4 as they are frozen to 100 K, replicating the conditions that may occur when subsurface ocean fluids are emplaced onto Europa's surface. Confocal micro-Raman spectroscopy is used to study the formation of salts during the freezing process, and the interaction of ions in the frozen brines. Our data indicate that mixed aqueous solutions of NaCl and MgSO4 form Na2SO4 and MgCl2 preferentially when frozen, rather than making NaCl and MgSO4 precipitates. The detection of epsomite (MgSO4Ÿ•7H2O) on Europa's surface may therefore imply an ocean composition relatively low in sodium, unless radiolytic chemistry converts MgCl2 to MgSO4 as suggested by Hand and Brown 2013 (ApJ 145 110). These results have important implications for the interpretation of remote sensing data of Europa's surface.

Composition and structure of an iron-bearing, layered double hydroxide (LDH) - Green rust sodium sulphate

DEFF Research Database (Denmark)

Christiansen, B. C.; Balic-Zunic, T.; Petit, P. O.

2009-01-01

with Fe(II) and Fe(III) in an ordered distribution. The interlayers contain sulphate, water and sodium in an arrangement characteristic for the nikischerite group. The crystal structure is highly disordered by slacking faults. The composition, formula and crystallographic parameters are: NaFe(II)(6)Fe...

Biosedimentary and geochemical constraints on the precipitation of mineral crusts in shallow sulphate lakes

Science.gov (United States)

Cabestrero, Óscar; del Buey, Pablo; Sanz-Montero, M. Esther

2018-04-01

Seasonal desiccation of Mg2+-(Na+)-(Ca2+)-SO42--(Cl-) saline lakes in La Mancha (Central Spain) that host microbial mats led to the precipitation of hydrated Na-Mg sulphates and gypsum. Sulphates precipitated in the submerged conditions form extensive biolaminites, whilst in marginal areas they produce thin crusts. Sedimentological, mineralogical, petrographic and high resolution textural studies reveal that the crusts were formed within the benthic microbial mats that thrive at salinities ranging from 160 to 340 g·L-1. The minerals of the crusts are primary bloedite (Na2Mg(SO4)2·4H2O), epsomite (MgSO4·7H2O), gypsum (CaSO4·2H2O) and mirabilite (Na2SO4·10H2O), as well as secondary hexahydrite (MgSO4·6H2O) and thenardite (Na2SO4). Primary bloedite crystals, which form the framework of surficial and submerged crusts are seen to nucleate subaqueously and grow incorporatively within the matgrounds. Displacive and incorporative epsomite grows on previous bloedite crystals and also on the ground. Mirabilite is precipitated rapidly at the brine-air interface over bloedite and epsomite. Hexahydrite and thenardite are formed due to dehydration of epsomite and mirabilite, respectively. Hydrochemical modeling with PHREEQC indicated that evaporitic biolaminites are forming from brines undersaturated with respect to bloedite, epsomite and mirabilite, which suggests that the microorganisms contribute to the heterogeneous nucleation of the sulphates in the microbial mats. Unlike carbonates, the influence of microbes on the growth and morphology of complicated double salts such as bloedite has not been documented previously and provides a new perspective on the formation of hydrated sulphate minerals that are common on Earth as well as other planets.

Corrosion Fatigue Characteristics of 12Cr Alloy Steel in Na2SO4 Solution

Science.gov (United States)

Bae, D. H.; Cho, S. Y.

In order to estimate reliability of 12Cr alloy steel using as the turbine blade material of the steam power plant, its corrosion fatigue characteristics in Na2SO4 solution considering its percentage and temperature that were determined from the polarization test results were investigated, and compared with the results in air. The corrosion characteristic of 12Cr alloy steel was remarkably susceptible in 12.7wt.% (IM) Na2SO4 solution, and its susceptibility increased with the solution temperature increase. The corrosion fatigue characteristics in 12.7wt.% Na2SO4 solution were similar to that of in air at 25°C. The crack growth rate was however increased with the temperature of solution increase. The reasons showing such results are due to the difference of the crack growth mechanism according to the electro-chemical activity of the corrosion factors.

Effect of sodium borohydride synthesis on NaBH4-H2 system economics

International Nuclear Information System (INIS)

Tabakoglu, F. oeznur; Kurtulus, Guelbahar

2007-01-01

The hazards and negative impacts of fossil fuel usage on environment and the prospect of fossil fuel depletion in near future have urged scientists to search for and use clean energy sources and alternative fuels. Hydrogen is the best fuel among others, which can minimize the effects of global warming. Although it is currently more expensive than other fuels, it will be cheaper following further developments in hydrogen technologies from production till end-use. Hydrogen storage is a critical issue in terms of safety and economics of hydrogen energy system. Chemical hydrides are an attractive hydrogen storage method due to their potential of achieving high volumetric and gravimetric storage densities. Among chemical hydrides, sodium borohydride (NaBH 4 ) is given a big attention, due to its 10.8% theoretical hydrogen storage capacity. Hydrogen, which can be released by sodium borohydride hydrolysis reaction on-site, can be used in a proton exchange membrane fuel cell (PEMFC) at anode. on the other hand, sodium borohydride solution can be used directly in a borohydride fuel cell (DBFC) at anode. Like the other chemical hydrides, sodium borohydride has been an expensive material up to now, constituting a major obstacle to commercialization of sodium borohydride as a hydrogen storage method. This paper aims to give an approximate estimation process cost of the NaBH 4 -H 2 system by taking into account both the energy and raw material costs, starting with sodium borohydride production till recycling of it. Two different methods to synthesize sodium borohydride are analyzed and their effects on total cost are compared. It was found that the usage of Bayer process to synthesize sodium borohydride makes the overall sodium borohydride - hydrogen system cost higher than the total cost of the alternative process which starts with the production of sodium borohydride from borax decahydrate. (authors)

Thermodynamics of curium(III) in concentrated electrolyte solutions: formation of sulfate complexes in NaCl/Na2SO4 solutions

International Nuclear Information System (INIS)

Paviet, P.; Fanghaenel, T.; Klenze, R.; Kim, J.I.

1996-01-01

The formation of sulfate complexes of Curium in aqueous solutions is studied by time resolved laser fluorescence spectroscopy (TRLFS) at 25 C. The species Cm 3+ , Cm(SO 4 ) - , Cm(SO 4 ) - 2 and Cm(SO 4 ) 3- 3 are quantified spectroscopically in the trace concentration range by peak deconvolution of fluorescence emission spectra. The complex formation equilibria are measured in NaCl/ Na 2 SO 4 solutions of constant ionic strength (3 molal) as a function of the sulfate concentration. The stability constants of Cm(SO 4 ) + and Cm(SO 4 ) - 2 are determined to be log β 1 = 0.93±0.08 and log β 2 = 0.61±0.08, respectively. The complex Cm(SO 4 ) 3- 3 is found to be stable only at very high sulfate concentrations (above 1 molal) and therefore not considered for further evaluation. (orig.)

Unique edge-sharing sulfate-transition metal coordination in Na2M(SO4)2 (M=Ni and Co)

International Nuclear Information System (INIS)

Fry, Allyson M.; Sweeney, Owen T.; Adam Phelan, W.; Drichko, Natalia; Siegler, Maxime A.; McQueen, Tyrel M.

2015-01-01

Two compounds, Na 2 Ni(SO 4 ) 2 and Na 2 Co(SO 4 ) 2 , were synthesized and their structure and properties were characterized. They adopt a structure that contains a bidentate coordination of sulfate to the transition metal center, which was determined via single crystal X-ray diffraction combined with model refinements to both laboratory X-ray and time-of-flight neutron powder diffraction data. The compounds were both found to crystallize in the C2/c space group with Z=24 and a unit cell of a=23.3461(3) Å, b=10.3004(1) Å, c=17.4115(2) Å, β=98.8659(9)°, and V=4136.99(8) Å 3 for the cobalt analog and a=23.2253(1) Å, b=10.26155(6) Å, c=17.3353(1) Å, β=99.0376(5)°, and V=4080.20(5) Å 3 for the nickel analog. Magnetization measurements show that the transition metal centers have negligible interactions with neighboring sites. Infrared and Raman spectroscopies were used to further probe the unique sulfate-transition metal coordination, and confirm the bidentate binding motif. The resulting pseudo-trigonal bipyramidal coordination produces vivid violet, Na 2 Co(SO 4 ) 2 , and yellow, Na 2 Ni(SO 4 ) 2 , colors that were probed by diffuse reflectance. - Graphical abstract: Two blue distorted transition metal octahedra (oxygen in red) bridged by two sulfate tetrahedra are shown here. Each bridging sulfate tetrahedra shares an edge with one octahedron and a corner with the other. All of the remaining corners of the octahedra are corner sharing with four tetrahedra forming a polyhedral network. - Highlights: • Structure of Na2Ni(SO4)2 and Na2Co(SO4)2 is determined. • Unique sulfate-transition metal binding observed in the new structure. • Combined diffraction and spectroscopic techniques were used. • Magnetization measurements show negligible interactions between sites

Mechanistic and Kinetic Analysis of Na2SO4-Modified Laterite Decomposition by Thermogravimetry Coupled with Mass Spectrometry.

Directory of Open Access Journals (Sweden)

Song Yang

Full Text Available Nickel laterites cannot be effectively used in physical methods because of their poor crystallinity and fine grain size. Na2SO4 is the most efficient additive for grade enrichment and Ni recovery. However, how Na2SO4 affects the selective reduction of laterite ores has not been clearly investigated. This study investigated the decomposition of laterite with and without the addition of Na2SO4 in an argon atmosphere using thermogravimetry coupled with mass spectrometry (TG-MS. Approximately 25 mg of samples with 20 wt% Na2SO4 was pyrolyzed under a 100 ml/min Ar flow at a heating rate of 10°C/min from room temperature to 1300°C. The kinetic study was based on derivative thermogravimetric (DTG curves. The evolution of the pyrolysis gas composition was detected by mass spectrometry, and the decomposition products were analyzed by X-ray diffraction (XRD. The decomposition behavior of laterite with the addition of Na2SO4 was similar to that of pure laterite below 800°C during the first three stages. However, in the fourth stage, the dolomite decomposed at 897°C, which is approximately 200°C lower than the decomposition of pure laterite. In the last stage, the laterite decomposed and emitted SO2 in the presence of Na2SO4 with an activation energy of 91.37 kJ/mol. The decomposition of laterite with and without the addition of Na2SO4 can be described by one first-order reaction. Moreover, the use of Na2SO4 as the modification agent can reduce the activation energy of laterite decomposition; thus, the reaction rate can be accelerated, and the reaction temperature can be markedly reduced.

Sulphate removal from sodium sulphate-rich brine and recovery of barium as a barium salt mixture.

Science.gov (United States)

Vadapalli, Viswanath R K; Zvimba, John N; Mulopo, Jean; Motaung, Solly

2013-01-01

Sulphate removal from sodium sulphate-rich brine using barium hydroxide and recovery of the barium salts has been investigated. The sodium sulphate-rich brine treated with different dosages of barium hydroxide to precipitate barium sulphate showed sulphate removal from 13.5 g/L to less than 400 mg/L over 60 min using a barium to sulphate molar ratio of 1.1. The thermal conversion of precipitated barium sulphate to barium sulphide achieved a conversion yield of 85% using coal as both a reducing agent and an energy source. The recovery of a pure mixture of barium salts from barium sulphide, which involved dissolution of barium sulphide and reaction with ammonium hydroxide resulted in recovery of a mixture of barium carbonate (62%) and barium hydroxide (38%), which is a critical input raw material for barium salts based acid mine drainage (AMD) desalination technologies. Under alkaline conditions of this barium salt mixture recovery process, ammonia gas is given off, while hydrogen sulfide is retained in solution as bisulfide species, and this provides basis for ammonium hydroxide separation and recovery for reuse, with hydrogen sulfide also recoverable for further industrial applications such as sulfur production by subsequent stripping.

Preparation of Magnetite Nanocrystals from Ferrous Sulphate Solution

International Nuclear Information System (INIS)

Cho Yu Mon; Tint Tint Kywe; Moe Moe Kyaw

2010-12-01

Magnetite (Fe3O4) nanoparticle were prepared by hydrothermal process in two ways, which would be used for production of copier toner.In this investigation, the first process was made from ferrous sulphate (FeSO4 . 7H2O) by using 10 M sodium hydroxide solution. In this method, magnetite nanoparticles were prepared by changing aeration time from 1 to 3 hr and heated at 90C for 15 min. The alternative process was carried out from ferrous sulphate (FeSO4.7H2O) by using 6.6 M sodium hydroxide solution and sodium silicate solution.Magnetite (black iron oxide) was synthesized by using different aeration times and reaction times. Aeration time was changed from 1 to 2 hr and reaction time was changed from 1 to 5.5 hr at 85 C. The magnetites obtained were examined by X-ray Diffraction (XRD) analysis and Scanning Electron Microscopy (SEM) technique. The average particle size range of magnetite nanoprticles were 90-120 nm and 120-150 nm in each process. The maximum yied percentages of magnetite based on FeSO4 in both processing were found to be 46.30% and 60.72%. The precent yields of magnetite in both preparation based on theoretical yields were 91.02% and 94.83% respectively.

Synthesis, characterization and thermal decomposition of [Pd2 (C2-dmba (µ-SO4 (SO22

Directory of Open Access Journals (Sweden)

Caires Antonio Carlos Fávero

1998-01-01

Full Text Available The bridged sulphate complex [Pd2 (C²,dmba (µ-SO4 (SO22] has been obtained by reacting a saturated solution of SO2 in methanol and the cyclometallated compound [Pd(C²,N-dmba(µ-N3] 2; (dmba = N,N-dimethylbenzylamine, at room temperature for 24 h. Reaction product was characterized by elemental analysis, NMR comprising 13C{¹H} and ¹H nuclei and I.R. spectrum's measurements. Thermal behavior has been investigated and residual products identified by X-ray powder diffraction.

Osmotic and activity coefficients of {l_brace}y Na{sub 2}SO{sub 4} + (1 - y) ZnSO{sub 4}{r_brace}(aq) at T = 298.15 K

Energy Technology Data Exchange (ETDEWEB)

Marjanovic, V. [High Technical School, Trg Svetog Save 34, 31 000 Uzice (Serbia and Montenegro); Ninkovic, R. [Faculty of Technology and Metallurgy, University of Belgrade, Karnegijeva 4, 11 000 Belgrade (Serbia and Montenegro); Miladinovic, J. [Faculty of Technology and Metallurgy, University of Belgrade, Karnegijeva 4, 11 000 Belgrade (Serbia and Montenegro)]. E-mail: duma@elab.tmf.bg.ac.yu; Todorovic, M. [Faculty of Technology and Metallurgy, University of Belgrade, Karnegijeva 4, 11 000 Belgrade (Serbia and Montenegro); Pavicevic, V. [Faculty of Technology and Metallurgy, University of Belgrade, Karnegijeva 4, 11 000 Belgrade (Serbia and Montenegro)

2005-02-01

The osmotic coefficients of the mixed electrolyte solution {l_brace}y Na{sub 2}SO{sub 4} + (1 - y) ZnSO{sub 4}{r_brace}(aq) have been measured by the isopiestic method, at T = 298.5 K. The experimental results were treated by Scatchard's, Pitzer-Kim's and Clegg-Pitzer-Brimblecombe's methods for mixed-electrolyte solutions. By these methods, the activity coefficients for Na{sub 2}SO{sub 4} and ZnSO{sub 4} were calculated and compared. The Scatchard interaction parameters are used for calculation of the excess Gibbs free energy as a function of ionic strength and ionic-strength fraction of Na{sub 2}SO{sub 4}. Also, the Zdanovskii's rule of linearity is tested.

Selectivity of crystalline Cesup(IV) phosphate sulphate hydrates for Li+, Na+, K+, Rb+ Cs+, and NH4+ in absolute methanol and absolute dimethylsulphoxide

International Nuclear Information System (INIS)

Koenig, K.H.; Psotta, L.

1978-01-01

The sequence of exchange capacities of Cerium(IV) phosphate sulphate hydrate (CePO 4 ) 2 (HPO 4 )sub(0.74(SO 4 )sub(0.26) . 4.74 H 2 O for alkalimetal ions and ammoniumions in absolute methanol at 25 0 C for the case of a small excess of the exchanger (in relation to the equivalent amount) is given by K + > Rb + >= NH 4 + > Cs + > Na + > Li + . Between the exchange capacity A of these cations and their ionic radii r (given by Ladd) exists the simple relation A = const./r. For Na + the radius of the inner hydration shell must be considered. In absolute dimethyl-sulphoxide under the same conditions the sequence is K + >= NH 4 + > Rb + > Na + > Cs + > Li + . For K + , NH 4 + , Rb + and Cs + the exchange capacity is given by A = const./r. + const. . r 4 . The sequences of the alkali ions in both solvents are among the group of 13 sequences which are physicaly significant according to Eisenmann's theory. The results are compared with the observations made with water as solvent. (author)

Biological reduction-deposition and luminescent properties of nanostructured CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Yu, Xiaoniu [School of Materials Science and Engineering, Southeast University, Nanjing 211189 (China); Research Institute of Green Construction Materials, Southeast University, Nanjing 211189 (China); Qian, Chunxiang, E-mail: cxqian@seu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189 (China); Research Institute of Green Construction Materials, Southeast University, Nanjing 211189 (China)

2016-03-01

Nano-sized CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} with hexagonal phase have been prepared by simply varying the reactant P/Ce molar ratio in bacterial liquid. The phase composition of two samples was checked via Fourier transform infrared spectroscopy (FTIR), energy dispersive analysis of X-rays (EDS) and X-ray diffraction (XRD) analyses, displaying the presence of CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} with average crystallite size are 32.34 and 15.61 nm, respectively. The scanning electron microscopy (SEM) images show that nano-clusters and sphere-like in shape with a narrow diameter distribution were observed in two samples. The transmission electron microscopy (TEM) photographs further indicate obtained CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} nanoparticles correspond to nanosheets and nanorods, respectively. The emission spectra of CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} display a broad band of 300–380 nm range with the strongest emission at 342 nm in the violet region. - Highlights: • A new method was found to synthesize CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} nanoparticles. • CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) nanoparticles have good luminescent properties. • Size and luminescent properties of two samples have been studied and compared.

Densities and apparent molar volumes of atmospherically important electrolyte solutions. 1. The solutes H2SO4, HNO3, HCl, Na2SO4, NaNO3, NaCl, (NH4)2SO4, NH4NO3, and NH4Cl from 0 to 50 °C, including extrapolations to very low temperature and to the pure liquid state, and NaHSO4, NaOH, and NH3 at 25 °C.

Science.gov (United States)

Clegg, S L; Wexler, A S

2011-04-21

Calculations of the size and density of atmospheric aerosols are complicated by the fact that they can exist at concentrations highly supersaturated with respect to dissolved salts and supercooled with respect to ice. Densities and apparent molar volumes of solutes in aqueous solutions containing the solutes H(2)SO(4), HNO(3), HCl, Na(2)SO(4), NaNO(3), NaCl, (NH(4))(2)SO(4), NH(4)NO(3), and NH(4)Cl have been critically evaluated and represented using fitted equations from 0 to 50 °C or greater and from infinite dilution to concentrations saturated or supersaturated with respect to the dissolved salts. Using extrapolated densities of high-temperature solutions and melts, the relationship between density and concentration is extended to the hypothetical pure liquid solutes. Above a given reference concentration of a few mol kg(-1), it is observed that density increases almost linearly with decreasing temperature, and comparisons with available data below 0 °C suggest that the fitted equations for density can be extrapolated to very low temperatures. As concentration is decreased below the reference concentration, the variation of density with temperature tends to that of water (which decreases as temperature is reduced below 3.98 °C). In this region below the reference concentration, and below 0 °C, densities are calculated using extrapolated apparent molar volumes which are constrained to agree at the reference concentrations with an equation for the directly fitted density. Calculated volume properties agree well with available data at low temperatures, for both concentrated and dilute solutions. Comparisons are made with literature data for temperatures of maximum density. Apparent molar volumes at infinite dilution are consistent, on a single ion basis, to better than ±0.1 cm(3) mol(-1) from 0 to 50 °C. Volume properties of aqueous NaHSO(4), NaOH, and NH(3) have also been evaluated, at 25 °C only. In part 2 of this work (ref 1 ) an ion interaction (Pitzer

Synthesis and thermal stability of the sodalite Na6Zn2[Al6Si6O24](SO4)2 and its reaction with hydrogen

DEFF Research Database (Denmark)

Heiden, Frank; Nielsen, Ulla Gro; Warner, Terence Edwin

2012-01-01

Ca2[Al6Si6O24](SO4)2. Na6Zn2[Al6Si6O24](SO4)2 was shown to be largely immiscible with nosean, Na8[Al6Si6O24]SO4 in the solid-state. Na6Zn2[Al6Si6O24](SO4)2 decomposes above 700 °C, yielding nosean, Na8[Al6Si6O24]SO4; willemite, Zn2SiO4; gahnite, ZnAl2O4; and presumably a glass phase, 2Na2O•9SiO2...

Bacterial sulphate reduction and the development of alkalinity. I. Experiments with synthetic media

Energy Technology Data Exchange (ETDEWEB)

Abd-El-Malek, Y; Rizk, S G

1963-01-01

In liquid cultures of desulphovibrio desulphuricans the effects of the following on sulphate reduction were determined: The type of cation (ca++ or na+) attached to the sulphate ion; the presence of calcium carbonate alone and with sodium chloride; the concentration of sodium sulphate, sodium lactate and sodium chloride; and the initial pH. The titratable alkalinity formed as a result of sulphate reduction was found to be quantitatively related to the sulphate reduced, and apparently unaffected by strain variation or energy source.

Microwave assisted synthesis of nano sized sulphate doped hydroxyapatite

International Nuclear Information System (INIS)

Alshemary, Ammar Z.; Goh, Yi-Fan; Akram, Muhammad; Razali, Ili Rabihah; Abdul Kadir, Mohammed Rafiq; Hussain, Rafaqat

2013-01-01

Highlights: ► Phase pure nano-sized sulphur doped hydroxyapatite has been synthesized. ► TEM analysis confirmed formation of needle shaped structure. ► Lattice parameters and cell volume increased with increase in sulphate doping. ► Crystallite size decreased as sulphate content inside the structure increased. ► Degree of crystallinity decreased with increase in sulphate substitution. - Abstract: Inorganic sulphate is required by all mammalian cells to function properly, it is the fourth most abundant anion in the human plasma. Sulphate ions are the major source of sulphur which is considered an important element for sustenance of life as it is present in the essential amino and is required by cells to function properly. In this study we have successfully substituted sulphate ions (SO 4 2− ) into hydroxyapatite (Ca 10 (PO 4 ) 6−x (SO 4 ) x (OH) 2−x ) lattice via ion exchange process with phosphate group. Concentration of SO 4 2− ions was varied between X = 0.05–0.5, using (Ca (NO 3 ) 2 ·4H 2 O), ((NH 4 ) 2 HPO 4 ) and (Na 2 SO 4 ) as starting materials. X-ray diffraction (XRD), Fourier transform IR spectroscopy (FTIR), showed that the substitution of SO 4 2− ions into the lattice resulted in peak broadening and reduced peak height due to the amorphous nature and reduced crystallinity of the resulting HA powder. Transmission electron microscopy (TEM) and field emission electron microscopy (FESEM) analysis confirmed the formation of needle shaped particles of 41 nm size with homogenous and uniform distribution of element within the HA structure

Towards highly stable storage of sodium ions: a porous Na(3)V(2)(PO(4))(3)/C cathode material for sodium-ion batteries.

Science.gov (United States)

Shen, Wei; Wang, Cong; Liu, Haimei; Yang, Wensheng

2013-10-18

A porous Na3 V2 (PO4 )3 cathode material coated uniformly with a layer of approximately 6 nm carbon has been synthesized by the sol-gel method combined with a freeze-drying process. The special porous morphology and structure significantly increases the specific surface area of the material, which greatly enlarges the contact area between the electrode and electrolyte, and consequently supplies more active sites for sodium ions. When employed as a cathode material of sodium-ion batteries, this porous Na3 V2 (PO4 )3 /C exhibits excellent rate performance and cycling stability; for instance, it shows quite a flat potential plateau at 3.4 V in the potential window of 2.7-4.0 V versus Na(+) /Na and delivers an initial capacity as high as 118.9 and 98.0 mA h g(-1) at current rates of 0.05 and 0.5 C, respectively, and after 50 cycles, a good capacity retention of 92.7 and 93.6 % are maintained. Moreover, even when the discharge current density is increased to 5 C (590 mA g(-1) ), an initial capacity of 97.6 mA h g(-1) can still be achieved, and an exciting capacity retention of 88.6 % is obtained after 100 cycles. The good cycle performance, excellent rate capability, and moreover, the low cost of Na3 V2 (PO4 )3 /C suggest that this material is a promising cathode for large-scale sodium-ion rechargeable batteries. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microwave assisted synthesis of nano sized sulphate doped hydroxyapatite

Energy Technology Data Exchange (ETDEWEB)

Alshemary, Ammar Z.; Goh, Yi-Fan; Akram, Muhammad; Razali, Ili Rabihah [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor Darul Ta’zim (Malaysia); Abdul Kadir, Mohammed Rafiq [Medical Implant Technology Group, Faculty of Biomedical Engineering and Health Science, Universiti Teknologi Malaysia,81310 UTM Skudai, Johor Darul Ta’zim (Malaysia); Hussain, Rafaqat, E-mail: rafaqat@kimia.fs.utm.my [Ibnu Sina Institute for Fundamental Science Studies, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor DarulTa’zim (Malaysia)

2013-06-01

Highlights: ► Phase pure nano-sized sulphur doped hydroxyapatite has been synthesized. ► TEM analysis confirmed formation of needle shaped structure. ► Lattice parameters and cell volume increased with increase in sulphate doping. ► Crystallite size decreased as sulphate content inside the structure increased. ► Degree of crystallinity decreased with increase in sulphate substitution. - Abstract: Inorganic sulphate is required by all mammalian cells to function properly, it is the fourth most abundant anion in the human plasma. Sulphate ions are the major source of sulphur which is considered an important element for sustenance of life as it is present in the essential amino and is required by cells to function properly. In this study we have successfully substituted sulphate ions (SO{sub 4}{sup 2−}) into hydroxyapatite (Ca{sub 10}(PO{sub 4}){sub 6−x}(SO{sub 4}){sub x}(OH){sub 2−x}) lattice via ion exchange process with phosphate group. Concentration of SO{sub 4}{sup 2−} ions was varied between X = 0.05–0.5, using (Ca (NO{sub 3}){sub 2}·4H{sub 2}O), ((NH{sub 4}){sub 2}HPO{sub 4}) and (Na{sub 2}SO{sub 4}) as starting materials. X-ray diffraction (XRD), Fourier transform IR spectroscopy (FTIR), showed that the substitution of SO{sub 4}{sup 2−} ions into the lattice resulted in peak broadening and reduced peak height due to the amorphous nature and reduced crystallinity of the resulting HA powder. Transmission electron microscopy (TEM) and field emission electron microscopy (FESEM) analysis confirmed the formation of needle shaped particles of 41 nm size with homogenous and uniform distribution of element within the HA structure.

Radiation Effects on Polymers - XIII

DEFF Research Database (Denmark)

El-Awady, N. I.; Ghanem, N. A.; Bo, P.

1979-01-01

Using computerized programs, the water flux and salt rejection properties in reverse osmosis of cellulose acetate-g-acrylamide membranes are determined. Comparisons are made with ungrafted commercial cellulose acetate membranes, using 0.1 and 1.0 M sodium chloride, sodium sulphate and ammonium su...... sulphate solutions. The grafted cellulose acetates show improved water flux but reduced NaCl rejection. However, they show promising prospects in bigger ion separation as for Na2SO4 and (NH4)2SO4 solutions....

First-principles study of mixed eldfellite compounds Nax(Fe1/2M1/2) (SO4)2 (x=0-2, M = Mn, Co, Ni): A new family of high electrode potential cathodes for the sodium-ion battery

Science.gov (United States)

Ri, Gum-Chol; Choe, Song-Hyok; Yu, Chol-Jun

2018-02-01

Natural abundance of sodium and its similar behavior to lithium triggered recent extensive studies of cost-effective sodium-ion batteries (SIBs) for large-scale energy storage systems. A challenge is to develop electrode materials with a high electrode potential, specific capacity and a good rate capability. In this work we propose mixed eldfellite compounds Nax(Fe1/2M1/2) (SO4)2 (x = 0-2, M = Mn, Co, Ni) as a new family of high electrode potential cathodes of SIBs and present their material properties predicted by first-principles calculations. The structural optimizations show that these materials have significantly small volume expansion rates below 5% upon Na insertion/desertion with negative Na binding energies. Through the electronic structure calculations, we find band insulating properties and hole (and/or electron) polaron hoping as a possible mechanism for the charge transfer. Especially we confirm the high electrode voltages over 4 V with reasonably high specific capacities. We also investigate the sodium ion mobility by estimating plausible diffusion pathways and calculating the corresponding activation barriers, demonstrating the reasonably fast migrations of sodium ions during the operation. Our calculation results indicate that these mixed eldfellite compounds can be suitable materials for high performance SIB cathodes.

Neutron diffraction studies of the Na-ion battery electrode materials NaCoCr{sub 2}(PO{sub 4}){sub 3}, NaNiCr{sub 2}(PO{sub 4}){sub 3}, and Na{sub 2}Ni{sub 2}Cr(PO{sub 4}){sub 3}

Energy Technology Data Exchange (ETDEWEB)

Yahia, H. Ben [Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, Qatar Foundation, P.O. Box 5825 Doha (Qatar); Essehli, R., E-mail: ressehli@qf.org.qa [Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, Qatar Foundation, P.O. Box 5825 Doha (Qatar); Avdeev, M. [Australian Nuclear Science and Technology Organisation, New Illawarra Road, Lucas Heights NSW 2234 (Australia); Park, J-B.; Sun, Y-K. [Department of Energy Engineering Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Al-Maadeed, M.A. [Center for Advanced Materials (CAM), Qatar University, 2713 Doha (Qatar); Belharouak, I., E-mail: ibelharouak@qf.org.qa [Qatar Environment and Energy Research Institute, Hamad Bin Khalifa University, Qatar Foundation, P.O. Box 5825 Doha (Qatar)

2016-06-15

The new compounds NaCoCr{sub 2}(PO{sub 4}){sub 3}, NaNiCr{sub 2}(PO{sub 4}){sub 3}, and Na{sub 2}Ni{sub 2}Cr(PO{sub 4}){sub 3} were synthesized by sol-gel method and their crystal structures were determined by using neutron powder diffraction data. These compounds were characterized by galvanometric cycling and cyclic voltammetry. NaCoCr{sub 2}(PO{sub 4}){sub 3}, NaNiCr{sub 2}(PO{sub 4}){sub 3}, and Na{sub 2}Ni{sub 2}Cr(PO{sub 4}){sub 3} crystallize with a stuffed α-CrPO{sub 4}-type structure. The structure consists of a 3D-framework made of octahedra and tetrahedra that are sharing corners and/or edges generating channels along [100] and [010], in which the sodium atoms are located. Of significance, in the structures of NaNiCr{sub 2}(PO{sub 4}){sub 3}, and Na{sub 2}Ni{sub 2}Cr(PO{sub 4}){sub 3} a statistical disorder Ni{sup 2+}/Cr{sup 3+} was observed on both the 8g and 4a atomic positions, whereas in NaCoCr{sub 2}(PO{sub 4}){sub 3} the statistical disorder Co{sup 2+}/Cr{sup 3+} was only observed on the 8g atomic position. When tested as negative electrode materials, NaCoCr{sub 2}(PO{sub 4}){sub 3}, NaNiCr{sub 2}(PO{sub 4}){sub 3}, and Na{sub 2}Ni{sub 2}Cr(PO{sub 4}){sub 3} delivered specific capacities of 352, 385, and 368 mA h g{sup −1}, respectively, which attests to the electrochemical activity of sodium in these compounds. - Highlights: • NaCoCr{sub 2}(PO{sub 4}){sub 3}, NaNiCr{sub 2}(PO{sub 4}){sub 3}, and Na{sub 2}Ni{sub 2}Cr(PO{sub 4}){sub 3} were synthesized by sol-gel method. • The crystal structures were determined by using neutron powder diffraction data. • The three compounds crystallize with a stuffed α-CrPO{sub 4}-type structure. • The three compounds were tested as anodes in sodium-ion batteries. • Relatively high specific capacities were obtained for these compounds.

Hydrolysis and regeneration of sodium borohydride (NaBH4) - A combination of hydrogen production and storage

Science.gov (United States)

Chen, W.; Ouyang, L. Z.; Liu, J. W.; Yao, X. D.; Wang, H.; Liu, Z. W.; Zhu, M.

2017-08-01

Sodium borohydride (NaBH4) hydrolysis is a promising approach for hydrogen generation, but it is limited by high costs, low efficiency of recycling the by-product, and a lack of effective gravimetric storage methods. Here we demonstrate the regeneration of NaBH4 by ball milling the by-product, NaBO2·2H2O or NaBO2·4H2O, with MgH2 at room temperature and atmospheric pressure without any further post-treatment. Record yields of NaBH4 at 90.0% for NaBO2·2H2O and 88.3% for NaBO2·4H2O are achieved. This process also produces hydrogen from the splitting of coordinate water in hydrated sodium metaborate. This compensates the need for extra hydrogen for generating MgH2. Accordingly, we conclude that our unique approach realizes an efficient and cost-effective closed loop system for hydrogen production and storage.

Carbonate mineral solubility at low temperatures in the Na-K-Mg-Ca-H-Cl-SO 4-OH-HCO 3-CO 3-CO 2-H 2O system

Science.gov (United States)

Marion, Giles M.

2001-06-01

Carbonate minerals have played an important role in the geochemical evolution of Earth, and may have also played an important role in the geochemical evolution of Mars and Europa. Several models have been published in recent years that describe chloride and sulfate mineral solubilities in concentrated brines using the Pitzer equations. Few of these models are parameterized for subzero temperatures, and those that are do not include carbonate chemistry. The objectives of this work are to estimate Pitzer-equation bicarbonate-carbonate parameters and carbonate mineral solubility products and to incorporate them into the FREZCHEM model to predict carbonate mineral solubilities in the Na-K-Mg-Ca-H-Cl-SO 4-OH-HCO 3-CO 3-CO 2-H 2O system at low temperatures (≤25°C) with a special focus on subzero temperatures. Most of the Pitzer-equation parameters and equilibrium constants are taken from the literature and extrapolated into the subzero temperature range. Solubility products for 14 sodium, potassium, magnesium, and calcium bicarbonate and carbonate minerals are included in the model. Most of the experimental data are at temperatures ≥ -8°C; only for the NaHCO 3-NaCl-H 2O and Na 2CO 3-NaCl-H 2O systems are there bicarbonate and carbonate data to temperatures as low as -21.6°C. In general, the fit of the model to the experimental data is good. For example, calculated eutectic temperatures and compositions for NaHCO 3, Na 2CO 3, and their mixtures with NaCl and Na 2SO 4 salts are in good agreement with experimental data to temperatures as low as -21.6°C. Application of the model to eight saline, alkaline carbonate waters give predicted pHs ranging from 9.2 to 10.2, in comparison with measured pHs that range from 8.7 to 10.2. The model suggests that the CaCO 3 mineral that precipitates during seawater freezing is probably calcite and not ikaite. The model demonstrates that a proposed salt assemblage for the icy surface of Europa consisting of highly hydrated MgSO 4

Electrochemical and spectroscopie behaviour of iron in the molten NaCl-K2SO4 mixture

DEFF Research Database (Denmark)

Bjerrum, Niels; Petruchina, Irina; Volkov, S.V.

1996-01-01

The chemical and electrochemical dissolving of Armco iron in the NaCl-K2SO4 melt has been studied. In the case of the chemical dissolution, a sample becomes coated, as time goes on, with a dense film consisting of FeO, FeS and Fe3O4; precipitation in the melt is observed, the precipitate consisting...... not detect Fe(III) by electronic absorption spectra, possibly due to the superimposition of the charge transfer bands edge on low-intensity Fe(III) bands of the 5d electronic configuration. The solubility of Fe2O3 in the NaCl-K2SO4 melt is low and was determined to 2 x 10(-3) wt%....

Validation of a chromatographic method and its use in the determination of sulphates in the products of atmospheric corrosion of zinc exposed to SO2 and NO2

International Nuclear Information System (INIS)

Montoya, Paula; Castano, Juan G

2005-01-01

The role of SO 2 and NO 2 in the atmospheric corrosion of zinc was studied by determining sulphates as the main products of corrosion when this metal is exposed to atmospheres containing SO 2 and NO 2 , scanning electron microscopy (SEM/EDX) and Ion Exchange Chromatography (IC) were used as instrumental techniques, the former was used to establish the morphology and the elementary qualitative determination of corrosion products, and the latter to quantify sulphates, before conducting the chromatographic analyses a series of parameters such as selectivity, linearity, precision, accuracy, limit of quantification, and detection limit, were evaluated to validate the method and to have the statistical certainty of its utility in the sulphate quantification, the results showed that when the metal is exposed to an atmosphere containing SO 2 and NO 2 , the sulphate formation increases with exposure time, a synergetic effect of both polluting agents on sulphate formation was found with respect to the sulphate formation in atmospheres containing only SO 2

On synthesis of LiCe(SO4)2xH2O double salt in hydrothermal conditions

International Nuclear Information System (INIS)

Bondar', S.A.; Belokoskov, V.I.; Popova, R.A.; Nikitina, S.D.; Trofimov, G.V.; Korobejnikov, L.S.

1986-01-01

Conditions for LiCe(SO 4 ) 2 xH 2 O double sulfate crystallization are determined by investigation of Li 2 SO 4 -Ce 4 (SO 4 ) 3 -H 2 SO 4 -H 2 O system using the method of isothermal solubility at 150 and 200 deg C in the 35-85 mass % concentration range of sulfuric acid and ratios at mixture charge of Li 2 SO 4 :Ce(SO 4 ) 3 equal to 2:1 and 5:1 (g/mole). Derivatograms, infrared spectra and crystal optical characteristics of double lithium and cerium (3) sulphate are presented

Bacterial Reduction Of Barium Sulphate By Sulphate-Reducing Bacteria

Directory of Open Access Journals (Sweden)

Luptáková Alena

2015-12-01

Full Text Available Acid mine drainage (AMD is a worldwide problem leading to contamination of water sources. AMD are characterized by low pH and high content of heavy metals and sulphates. The barium salts application presents one of the methods for the sulphates removing from AMD. Barium chloride, barium hydroxide and barium sulphide are used for the sulphates precipitation in the form of barium sulphate. Because of high investment costs of barium salts, barium sulphide is recycled from barium sulphate precipitates. It can be recycled by thermic or bacterial reduction of barium sulphate. The aim of our study was to verify experimentally the possibility of the bacterial transformation of BaSO4 to BaS by sulphate-reducing bacteria. Applied BaSO4 came from experiments of sulphates removal from Smolnik AMD using BaCl2.

Ionic strength dependence of the oxidation of SO2 by H2O2 in sodium chloride particles

Science.gov (United States)

Ali, H. M.; Iedema, M.; Yu, X.-Y.; Cowin, J. P.

2014-06-01

The reaction of sulfur dioxide and hydrogen peroxide in the presence of deliquesced (>75% RH) sodium chloride (brine) particles was studied by utilizing a cross flow mini-reactor. The reaction kinetics were followed by observing chloride depletion in particles by computer-controlled scanning electron microscope with energy dispersive X-ray analysis, namely CCSEM/EDX. The reactions take place in concentrated mixed salt brine aerosols, for which no complete kinetic equilibrium data previously existed. We measured the Henry's law solubility of H2O2 in brine solutions to close that gap. We also calculated the reaction rate as the particle transforms continuously from concentrated NaCl brine to, eventually, a mixed NaHSO4 plus H2SO4 brine solution. The reaction rate of the SO2 oxidation by H2O2 was found to be influenced by the change in ionic strength as the particle undergoes compositional transformation, following closely the dependence of the third order rate constant on ionic strength as predicted using established rate equations. This is the first study that has measured the ionic strength dependence of sulfate formation (in non-aqueous media) from oxidation of mixed salt brine aerosols in the presence of H2O2. It also gives the first report of the dependence of the Henry's law constant of H2O2 on ionic strength.

Simultaneous absorption of SO2 and NO from flue gas with KMnO4/NaOH solutions

International Nuclear Information System (INIS)

Chu, H.; Chien, T.W.; Li, S.Y.

2001-01-01

The wet scrubbing combined SO x /NO x removal system is an advanced air pollution control device. This study attempts to understand the absorption kinetics in the system. The absorption of diluted SO 2 and simultaneous absorption of diluted SO 2 and NO, as occurs in flue gases, in a stirred tank reactor with KMnO 4 /NaOH solutions were carried out at 50C. The liquid-side and gas-side mass transfer coefficients of the system were determined. The results indicate that the absorption of SO 2 is close to completely gas-film controlled where the NaOH concentration is greater than 0.1 M or the KMnO 4 concentration is greater than 0.05 M. The increasing gas flow rate has a positive effect on the absorption rate of SO 2 . The existence of O 2 has no significant effect on the absorption rate of SO 2 . Adding SO 2 would decrease the absorption rate of NO; however, the addition of NO has no effect on the absorption rate of SO 2

EPR study of gamma irradiated N-methyl taurine (C 3H 9NO 3S) and sodium hydrogen sulphate monohydrate (NaHSO 3·H 2O) single crystals

Science.gov (United States)

Yıldırım, İlkay; Karabulut, Bünyamin

2011-03-01

EPR study of gamma irradiated C 3H 9NO 3S and NaHSO 3.H 2O single crystals have been carried out at room temperature. There is one site for the radicals in C 3H 9NO 3S and two magnetically distinct sites for the radicals in NaHSO 3. The observed lines in the EPR spectra have been attributed to the species of SO3- and RH radicals for N-methyl taurine, and to the SO3- and OH radicals for sodium hydrogen sulfate monohydrate single crystals. The principal values of the g for SO3-, the hyperfine values of RH and OH proton splitting have been calculated and discussed.

Interaction of low-expansion NZP ceramics with Na{sub 2}SO{sub 4} at 1000{degrees}C

Energy Technology Data Exchange (ETDEWEB)

Lee, W.Y.; Cooley, K.M.; Stinton, D.P.; Joslin, D.L. [Oak Ridge National Lab., TN (United States)

1996-08-01

The interaction between several low-expansion NZP materials and Na{sub 2}SO{sub 4} at 1000{degrees}C in pure O{sub 2} was studied. Ba{sub 1.25}Zr{sub 4}P{sub 5.5}Si{sub 0.5}O{sub 24} experienced extensive cracking and delamination upon reaction with Na{sub 2}SO{sub 4}. On the other hand, Ca{sub 0.5}Sr{sub 0.5}Zr{sub 4}P{sub 6}O{sub 24} remained intact in terms of visual appearance, and had no significant weight loss or gain. However, the ion exchange between Na{sup +} ions and Ca{sup +2} ions was observed to be sufficiently rapid to allow the penetration of the Na{sup +} ions into the test specimens in 100h. The segregation of Ca to the specimen surface was observed due to the ion exchange. Ca{sub 0.6}Mg{sub 0.4}Zr{sub 4}P{sub 6}O{sub 24} was also tested, but its stability could not properly be assessed because the as-received specimens contained a significant amount of MgZr{sub 4}P{sub 6}O{sub 24} as an impurity phase.

Physiochemical properties and reproducibility of air-based sodium tetradecyl sulphate foam using the Tessari method.

Science.gov (United States)

Watkins, Mike R; Oliver, Richard J

2017-07-01

Objectives The objectives were to examine the density, bubble size distribution and durability of sodium tetradecyl sulphate foam and the consistency of production of foam by a number of different operators using the Tessari method. Methods 1% and 3% sodium tetradecyl sulphate sclerosant foam was produced by an experienced operator and a group of inexperienced operators using either a 1:3 or 1:4 liquid:air ratio and the Tessari method. The foam density, bubble size distribution and foam durability were measured on freshly prepared foam from each operator. Results The foam density measurements were similar for each of the 1:3 preparations and for each of the 1:4 preparations but not affected by the sclerosant concentration. The bubble size for all preparations were very small immediately after preparation but progressively coalesced to become a micro-foam (foams developed liquid more rapidly when made in a 1:3 ratio (37 s) than in a 1:4 ratio (45 s) but all combinations took similar times to reach 0.4 ml liquid formation. For all the experiments, there was no statistical significant difference between operators. Conclusions The Tessari method of foam production for sodium tetradecyl sulphate sclerosant is consistent and reproducible even when made by inexperienced operators. The best quality foam with micro bubbles should be used within the first minute after production.

Effects of Na4EDTA and EDTA on seeded precipitation of sodium aluminate solution

Institute of Scientific and Technical Information of China (English)

吕保林; 陈启元; 尹周澜; 胡慧萍

2010-01-01

Na4EDTA and EDTA were adopted as new additives to intensify the seeded precipitation process of sodium aluminate solution. The effects of the two additives at certain concentrations on the seeded precipitation rate of sodium aluminate solution, particle size distribution (PSD) and morphology of precipitated gibbsite were investigated using titration method, particle size analyzer and scanning electron microscope (SEM), respectively. The results show that the two additives can accelerate the seeded precipitation rate of sodium aluminate solution. At relatively high concentration, the facilitative effect of EDTA on sodium aluminate solution is more obvious than that of Na4EDTA. EDTA makes gibbsite particles thinner than Na4EDTA. The Na+ and H+ result in the different effects on the seeded precipitation rate of sodium aluminate solution in spite of the same EDTA anion in the two additives.

Sodium Sulphate Effect on Cement Produced with Building Stone Waste

Directory of Open Access Journals (Sweden)

Emre Sancak

2015-01-01

Full Text Available In this study, the blended cements produced by using the building stone waste were exposed to sulphate solution and the cement properties were examined. Prepared mortar specimens were cured under water for 28 days and then they were exposed to three different proportions of sodium sulphate solution for 125 days. Performances of cements were determined by means of compressive strength and tensile strength tests. The broken parts of some mortar bars were examined with scanning electron microscope (SEM. Besides, they were left under moist atmosphere and their length change was measured and continuously monitored for period of 125 days. In blended cements, solely cements obtained by replacing 10–20% of diatomites gave similar strength values with ordinary Portland cement (CEM I 42.5R at the ages of 7, 28, and 56 days. In all mortar specimens that included either waste andesite (AP or marble powder (MP showed best performance against very severe effective sodium sulphate solutions (13500 mg/L.

Influence of chromium III ions on the electrical properties of NaNH4SO4.2H2O crystals

International Nuclear Information System (INIS)

Kassem, M.E.; El-Wahidy, E.F.; Hedewy, S.; Darwish, H.G.; Ramadan, T.

1991-07-01

The dielectric constant, ε, and electric conductivity, σ, of pure and Cr +3 doped samples of NaNH 4 SO 4 .2H 2 O are measured in the temperature range 20-300 K. The maximum value of dielectric constant in different crystallographic axes is presented and discussed. The effect of foreign ions on the critical behaviour and transition temperature T c is studied. (author). 18 refs, 2 figs, 1 tab

Anisotropy in elastic properties of lithium sodium sulphate ...

Indian Academy of Sciences (India)

Anisotropy in elastic properties of lithium sodium sulphate hexahydrate single crystal—An ultrasonic study. GEORGE VARUGHESE. ,∗. , A S KUMAR†, J PHILIP†† and GODFREY LOUIS#. Department of Physics, Catholicate College, Pathanamthitta 689 648, India. †SPAP, M.G. University, Kottayam 686 560, India. ††STIC ...

EFFECT OF SODIUM SILICATE TO SODIUM HYDROXIDE RATIOS ON DURABILITY OF GEOPOLYMER MORTARS CONTAINING NATURAL AND ARTIFICIAL POZZOLANS

Directory of Open Access Journals (Sweden)

F. Nurhayat Degirmenci

2017-09-01

Full Text Available This study aims to provide the experimental data on the sulphate and acid performance of geopolymer mortar containing pozzolanic materials such as fly ash (FA, ground granulated blast furnace slag (GGBS and natural zeolite (NZ. The alkaline solution was the combination of sodium silicate and sodium hydroxide solution with the ratio (Na ₂SiO₃/NaOH of 1.0, 2.0 and 3.0. The molarity of sodium hydroxide was fixed as 10. The performances of geopolymer mortar were measured in terms of sodium and magnesium sulphate resistance and sulphuric and hydrochlorich acid resistance with 5% and 10 % concentration after 24 weeks. The evaluations were measured as visual observation, measurement of weight change and residual compressive strength. It has been observed that Na ₂SiO₃/NaOH ratio is effective on residual compressive strength of geopolymer mortar in both sulphate and acid exposure. The higher ratio of Na ₂SiO₃/NaOH results in a higher residual compressive strength. The GGBS based geopolymer mortar has a very good resistance in acid media in terms of weight loss and residual compressive strength. The inclusion of FA in the GGBS based geopolymer mixture was found to be a suitable base of geopolymer mortar under ambient curing conditions.

THE REACTION BETWEEN ZnO AND MOLTEN NA2S2O7 OR K2S2O7 FORMING NA2Zn(SO4)2 OR K2Zn(SO4)2, STUDIED BY RAMAN SPECTROSCOPY AND X-RAY DIFFRACTION

DEFF Research Database (Denmark)

Berg, Rolf W.; Thorup, Niels

2005-01-01

Reactions between solid ZnO and molten Na2S2O7 or K2S2O7 at 500 are shown by Raman spectroscopy to be 1:1 reactions leading to solns. By lowering the temp. of the soln. melts, colorless crystals form. Raman spectra of the crystals are given and tentatively assigned. Crystal structures of the mon...... the three-dimensional network of the M2Zn(SO4)2 structures. Bond distances and angles compare well with literature values. Empirical correlations between S-O bond distances and av. O-S-O bond angles follow a previously found trend....

Thermal decomposition of uranyl sulphate hydrate

International Nuclear Information System (INIS)

Sato, T.; Ozawa, F.; Ikoma, S.

1980-01-01

The thermal decomposition of uranyl sulphate hydrate (UO 2 SO 4 .3H 2 O) has been investigated by thermogravimetry, differential thermal analysis, X-ray diffraction and infrared spectrophotometry. As a result, it is concluded that uranyl sulphate hydrate decomposes thermally: UO 2 SO 4 .3H 2 O → UO 2 SO 4 .xH 2 O(2.5 = 2 SO 4 . 2H 2 O → UO 2 SO 4 .H 2 O → UO 2 SO 4 → α-UO 2 SO 4 → β-UO 2 SO 4 → U 3 O 8 . (author)

Influence of Valsartan on the thermodynamics of micellization of anionic surfactant Sodium Dodecyl Sulphate

Directory of Open Access Journals (Sweden)

Stopková L.

2016-12-01

Full Text Available In this manuscript was investigated behaviour of drug valsartan by micellar media of anionic surfactant sodium dodecyl sulphate. As the method was used electrical conductivity for the determination of critical micelle concentration at different temperatures (T = 293.15 - 313.15 K, as well as calculated thermodynamic parameters like standard Gibbs free energy, enthalpy and entropy of micellization. According to contribution of Gibbs free energy is the process of micellization primarily controlled by entropy. Solubilization of valsartan was studied in surfactant system at 298.15 K and physiological conditions pH 7.4 using UV-spectrophotometry at different concentration range (0.001 - 0.07 mol/l of sodium dodecyl sulphate. The solubilization of drug was observed with increasing concentration of surfactant in aqueous solution.

Sulphate solubility and sulphate diffusion in oxide glasses: implications for the containment of sulphate-bearing nuclear wastes; Solubilite et cinetiques de diffusion des sulfates dans differents verres d'oxydes: application au conditionnement des dechets nucleaires sulfates

Energy Technology Data Exchange (ETDEWEB)

Lenoir, M.

2009-09-15

The thesis deals with sulphate solubility and sulphate diffusion in oxide glasses, in order to control sulphate incorporation and sulphate volatilization in nuclear waste glasses. It was conducted on simplified compositions, in the SiO{sub 2}-B{sub 2}O{sub 3}-R{sub 2}O (R = Li, Na, K, Cs), SiO{sub 2}-B{sub 2}O{sub 3}-BaO and V{sub 2}O{sub 5}-B{sub 2}O{sub 3}-BaO systems. These compositions allowed us to study the influence of the nature of network-modifying ions (Li{sup +}, Na{sup +}, K{sup +}, Cs{sup +} or Ba{sup 2+}) and also of former elements (Si, B, V), on structure and properties of glasses. Sulphate volatility is studied in sodium borosilicate melts using an innovative technique of sulphate quantitation with Raman spectroscopy. This technique is useful to obtain kinetic curves of sulphate volatilization. The establishment of a model to fit these curves leads to the determination of diffusion coefficients of sulphate. These diffusion coefficients can thus be compared to diffusion coefficients of other species, determined by other techniques and presented in the literature. They are also linked to diffusion coefficients in relation with the viscosity of the melts. Concerning sulphate solubility in glasses, it depends on glass composition and on the nature of sulphate incorporated. Sulphate incorporation in alkali borosilicate glasses leads to the formation of a sulphate layer floating on top of the melt. Sulphate incorporation in barium borosilicate and boro-vanadate glasses leads to the crystallization of sulphate species inside the vitreous matrix. Moreover, sulphate solubility is higher in these glasses than in alkali borosilicates. Finally, exchanges between cations present in glasses and cations present in the sulphate phase are also studied. (author)

Interaction of Celestine Concentrate and Reagent Grade SrSO4 with Oxalate Solutions

Directory of Open Access Journals (Sweden)

Abdullah Obut

2012-12-01

Full Text Available The interaction of reagent grade strontium sulphate and celestine concentrate with aqueous solutions of oxalic acid, sodiumoxalate and ammonium oxalate for the production of strontium carbonate were investigated for different oxalate compound:SrSO4 moleratios and reaction times using x-ray diffraction analysis and dissolution tests. Under the same experimental conditions, it was foundthat aqueous oxalic acid and sodium oxalate solutions had no or little effect on reagent grade strontium sulphate or celestineconcentrate, but aqueous ammonium oxalate solution converted them into strontium oxalate hydrate. Strontium carbonate was obtainedat conversion ratios of 74.7% for the celestine concentrate and 84.6 % for the reagent grade strontium sulphate by the decompositionof the obtained strontium oxalate hydrate at 600 °C under air atmosphere.

Degradation of wall paints due to sodium sulphate and sodium chloride crystallization

Directory of Open Access Journals (Sweden)

Díaz Gonçalves, T.

2003-03-01

Full Text Available A test method for evaluating wall paints behaviour to soluble salts crystallization was developed at LNEC. in the present paper, a recent set of tests is described and discussed. The major objectives were: analysing and comparing the behaviour of a common emulsion {"plastic" paint and a silicate-based paint; observing and comparing the effect of sodium sulphate, sodium chloride and distilled water on the paints and on a non-painted stone; evaluating this test method adequacy and effectiveness. The silicate-based paint showed a resistance to soluble salts crystallization greater than the one of the plastic paint. However, the degradation pattern of the silicate-based paint (blistering of a filmic layer was similar to the one of organic paints and distinct from the one of pure mineral paints. The amount of damage that a saline solution can cause to wall paints cannot be inferred from the amount of damage it can cause to stone. Sodium chloride seems to be able to cause more severe degradation to wall paints than sodium sulphate. To the unpainted stone, sodium sulphate seems to be more damaging than sodium chloride. The test method seems adequate to observe and compare the behaviour of wall paints under soluble salts action. However, lower (around 0.5% concentrations for both sodium sulphate and sodium chloride should be tested in the future.

RESUMEN En el LNEC se desarrolló una metodología de ensayo para evaluar la respuesta de pinturas aplicadas sobre paredes, frente a la cristalización de sales solubles. En este trabajo, se describen y discuten un conjunto de ensayos recientes. Los principales objetivos fueron: el análisis y la comparación del comportamiento de una pintura de emulsión común {''pintura plástica" y la de una pintura de silicato; la observación y la comparación de los efectos del sulfato de sodio, del cloruro de sodio y del agua destilada sobre las pinturas y sobre piedra no pintada; la evaluación de la adecuaci

Na7 [Fe2S6 ] , Na2 [FeS2 ] and Na2 [FeSe2 ] : New 'reduced' sodium chalcogenido ferrates

Science.gov (United States)

Stüble, Pirmin; Peschke, Simon; Johrendt, Dirk; Röhr, Caroline

2018-02-01

Three new 'reduced' FeII containing sodium chalcogenido ferrates were obtained applying a reductive synthetic route. The mixed-valent sulfido ferrate Na7 [Fe2S6 ] , which forms bar-shaped crystals with metallic greenish luster, was synthesized in pure phase from natural pyrite and elemental sodium at a maximum temperature of 800 °C. Its centrosymmetric triclinic structure (SG P 1 bar , a = 764.15(2), b = 1153.70(2), c = 1272.58(3) pm, α = 62.3325 (7) , β = 72.8345 (8) , γ = 84.6394 (8) ° , Z = 3, R1 = 0.0185) exhibits two crystallographically different [Fe2S6 ] 7 - dimers of edge-sharing [FeS4 ] tetrahedra, with somewhat larger Fe-S distances than in the fully oxidized FeIII dimers of e.g. Na6 [Fe2III S6 ] . In contrast to the localized AFM ordered pure di-ferrates(III), the Curie-Weiss behavior of the magnetic susceptibility proves the rarely observed valence-delocalized S = 9/2 state of the mixed-valent FeIII /FeII dimer. The nearly spin-only value of the magnetic moment combined with the chemical bonding not generally differing from that in pure ferrates(II) and (III), provides a striking argument, that the reduction of the local Fe spin moments observed in all condensed sulfido ferrate moieties is connected with the AFM spin ordering. The two isotypic ferrates(II) Na2 [FeS2 ] and Na2 [FeSe2 ] with chain-like structural units (SG Ibam, a = 643.54(8)/ 660.81(1), b = 1140.2(2)/1190.30(2) c = 562.90(6)/585.59(1) pm, Z = 4, R1 = 0.0372/0.0466) crystallize in the K2 [ZnO2 ] -type structure. Although representing merely further members of the common series of chalcogenido metallates(II) Na2 [MIIQ2 ] , these two new phases, together with Na6 [FeS4 ] and Li2 [FeS2 ] , are the only examples of pure FeII alkali chalcogenido ferrates. The new compounds allow for a general comparison of di- and chain ferrates(II) and (III) and mixed-valent analogs concerning the electronic and magnetic properties (including Heisenberg super-exchange and double-exchange interactions

A Green Route to a Na2FePO4F-Based Cathode for Sodium Ion Batteries of High Rate and Long Cycling Life.

Science.gov (United States)

Deng, Xiang; Shi, Wenxiang; Sunarso, Jaka; Liu, Meilin; Shao, Zongping

2017-05-17

Sodium ion batteries (SIBs) are considered one of the most promising alternatives for large-scale energy storage due largely to the abundance and low cost of sodium. However, the lack of high-performance cathode materials at low cost represents a major obstacle toward broad commercialization of SIB technology. In this work, we report a green route strategy that allows cost-effective fabrication of carbon-coated Na 2 FePO 4 F cathode for SIBs. By using vitamin C as a green organic carbon source and environmentally friendly water-based polyacrylic latex as the binder, we have demonstrated that the Na 2 FePO 4 F phase in the as-derived Na 2 FePO 4 F/C electrode shows a high reversible capacity of 117 mAh g -1 at a cycling rate of 0.1 C. More attractively, excellent rate capability is achieved while retaining outstanding cycling stability (∼85% capacity retention after 1000 charge-discharge cycles at a rate of 4 C). Further, in operando X-ray diffraction has been used to probe the evolution of phase structures during the charge-discharge process, confirming the structural robustness of the Na 2 FePO 4 F/C cathode (even when charged to 4.5 V). Accordingly, the poor initial Coulombic efficiency of some anode materials may be compensated by extracting more sodium ions from Na 2 FePO 4 F/C cathode at higher potentials (up to 4.5 V).

Structure of sodium alkyl sulphate micelles

International Nuclear Information System (INIS)

Vass, Sz.

1990-05-01

Micellar aggregation numbers of aggregated sodium octyl, decyl, dodecyl and tetradecyl sulphate molecules obtained from small-angle neutron scattering (SANS) measurements are reported. The surfactant concentration and solution temperature were varied systematically. A survey of the physical models and evaluation algorithms applied for SANS are presented. By utilizing a new least square fitting algorithm, the formation and annihilation parameters of orthopositronium in the micellar pseudophase and in the aqueous solvent is deduced by evaluating positron lifetime spectra measured by conventional technqiues. (R.P.) 157 refs.; 10 figs

3D organic Na4C6O6/graphene architecture for fast sodium storage with ultralong cycle life.

Science.gov (United States)

Gu, Jianan; Gu, Yue; Yang, Shubin

2017-11-23

Sodium-ion batteries (SIBs) have aroused increasing interest as one of the most promising replacements for lithium-ion batteries (LIBs). Here, a novel organic-inorganic 3D Na 4 C 6 O 6 -graphene architecture was successfully fabricated from commercial Na 2 C 6 O 6 and for the first time applied for sodium storage. Hence, the 3D Na 4 C 6 O 6 -graphene architecture exhibits a high reversible capacity, good cyclic performance and high-rate capability for sodium storage.

Exacerbation of alopecia areata: A possible complication of sodium tetradecyl sulphate foam sclerotherapy treatment for varicose veins.

Science.gov (United States)

Whiteley, Mark S; Smith, Victoria C

2017-01-01

A 40-year-old woman with a history of alopecia areata related to stress or hormonal changes was treated for bilateral primary symptomatic varicose veins (CEAP clinical score C2S) of pelvic origin, using a staged procedure. Her first procedure entailed pelvic vein embolisation of three pelvic veins using 14 coils and including foam sclerotherapy of the tributaries, using 3% sodium tetradecyl sulphate. Following this procedure, she had an exacerbation of alopecia areata with some moderate shedding of hair. Subsequently, she underwent endovenous laser ablation under local anaesthetic without incident. Seven months after the pelvic vein embolisation, she underwent foam sclerotherapy of leg and labial varicose veins using sodium tetradecyl sulphate. Two days following this procedure, she had a severe exacerbation of alopecia areata with gross shedding of hair. These two episodes of exacerbation of alopecia areata appear to be associated with sodium tetradecyl sulphate foam sclerotherapy of veins.

Electrochemical study in the molten sodium acid sulphate - potassium acid sulphate eutectic; Etude electrochimique dans l'eutectique fondu sulfate acide de sodium - sulfate acide de potassium

Energy Technology Data Exchange (ETDEWEB)

Le Ber, F [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

The general properties of the NaHSO{sub 4} - KHSO{sub 4} molten eutectic resemble those of neutral sulphates and those of concentrated H{sub 2}SO{sub 4}. We have been able to show the existence in solution of the ions HSO{sup -}{sub 4} SO{sup 2-}{sub 4}, and H{sub 3}O{sup +}, these last being formed by the action of the HSO{sup -}{sub 4} ions on dissolved H{sub 2}O. The electro-active zone with a polished platinum electrode is limited in oxidation by the ions H{sub 3}O{sup +} and SO{sup 2-}{sub 4}, and in reduction by the protons of HSO{sup -}{sub 4}. We have compared the electro-active zones obtained with different electrodes (Ag-Au-graphite-mercury). We have considered the dissolution of a few metallic oxides and halides. This work shows the role as O{sup 2-} ion acceptors of HSO{sup -}{sub 4} ions. We have undertaken an electro-chemical study of a few oxido-reduction Systems: H{sup +} / H{sub 2}, Ag{down_arrow} / Ag (1), the vanadium and uranium Systems, those of mercury Hg{down_arrow} / Hg{sup 2-}{sub 2} and of gold Au/Au{sup 3+}, then of the attack by the solvent of a few common metals such as aluminium, iron, copper and nickel. The study of silver Systems has made it possible to obtain the solubility products of AgCl and AgBr and to consider the possibility of coulometric titration Cl{sup -} ions with Ag{sup +} ions. We have shown the existence of various chemical species of vanadium which may exist in the molten eutectic. (author) [French] Les proprietes generales de l'eutectique NaHSO{sub 4} - KHSO{sub 4} fondu s'apparentent a celles des sulfates neutres et a celles de H{sub 2}SO{sub 4} concentre. Nous avons pu mettre en evidence l'existence en solution d'ions HSO{sup -}{sub 4}, SO{sup 2-}{sub 4},et H{sub 3}O{sup +}, ces derniers resultats de l'action des ions HSO{sup -}{sub 4} sur H{sup 2}O dissoute. Le domaine d'electroactivite a une electrode de platine poli est limite en oxydation par les ions H{sub 3}O{sup +} + SO{sup 2-}{sub 4} et en reduction par les

The effects of H2SO4 and NaOH solutions on irradiated sawdust for ethanol production

International Nuclear Information System (INIS)

Lina, M.R.; Susiana; Siagian, E.G.

1988-01-01

The research of gamma irradiated sawdust, which were added H2SO4 and NaOH solutions on fermentation process for ethanol production was investigated. Irradiation doses used were : 0 and 200 kGy, while H2SO4 and NaOH solutions had concentrations of 0,1 and 2% (v/v) and (b/v), with a ratio of sawdust weight and solution volume = 1:3. Fine powder of sawdust with a mesh of 60, was hydrolysed by enzyme (cellulase), S.cerevisiae was a yeast used for fermentation process and fermentation time was 4 hours. From the experimental results showed that irradiation doses up to 200 kGy, could increase the ethanol concentration from sawdust fermentation signivicantly (P= . Irradiation treatment, addition of the solutions and its interaction could not influence the total carbohydrate before and after fermentation. (author). 9 refs, 2 figs, 6 tabs

Exacerbation of alopecia areata: A possible complication of sodium tetradecyl sulphate foam sclerotherapy treatment for varicose veins

Directory of Open Access Journals (Sweden)

Mark S Whiteley

2017-05-01

Full Text Available A 40-year-old woman with a history of alopecia areata related to stress or hormonal changes was treated for bilateral primary symptomatic varicose veins (CEAP clinical score C2S of pelvic origin, using a staged procedure. Her first procedure entailed pelvic vein embolisation of three pelvic veins using 14 coils and including foam sclerotherapy of the tributaries, using 3% sodium tetradecyl sulphate. Following this procedure, she had an exacerbation of alopecia areata with some moderate shedding of hair. Subsequently, she underwent endovenous laser ablation under local anaesthetic without incident. Seven months after the pelvic vein embolisation, she underwent foam sclerotherapy of leg and labial varicose veins using sodium tetradecyl sulphate. Two days following this procedure, she had a severe exacerbation of alopecia areata with gross shedding of hair. These two episodes of exacerbation of alopecia areata appear to be associated with sodium tetradecyl sulphate foam sclerotherapy of veins.

Production of 34S-labeled gypsum (Ca34SO4.2H2O Produção de gesso (Ca34SO4.2H2O, marcado com 34S

Directory of Open Access Journals (Sweden)

Alexssandra Luiza Rodrigues Molina Rossete

2006-08-01

Full Text Available Agricultural gypsum (CaSO4.2H2O stands out as an effective source of calcium and sulfur, and to control aluminum saturation in the soil. Labeled as 34S it can elucidate important aspects of the sulfur cycle. Ca34SO4.2H2O was obtained by chemical reaction between Ca(OH2 and H2(34SO4, performed under slow agitation. The acid was produced by ion exchange chromatography using the Dowex 50WX8 cation exchange resin and a Na2(34SO4 eluting solution. After precipitation, the precipitate was separated and dried in a ventilated oven at 60ºC. From 2.2 L H2SO4 0.2 mol L-1 and 33.6 g Ca(OH2, 73.7 ± 0.6 g Ca34SO4.2H2O were produced on average in the tests, representing a mean yield of 94.6 ± 0.8%, with 98% purity. The 34SO2 gas was obtained from Ca34SO4.2H2O in the presence of NaPO3 in a high vacuum line and was used for the isotopic determination of S in an ATLAS-MAT model CH-4 mass spectrometer.O gesso agrícola (CaSO4.2H2O destaca-se como fonte eficiente de cálcio e enxofre e na redução da saturação de alumínio no solo. O 34S como traçador isotópico pode elucidar aspectos importantes no ciclo do enxofre. Para tanto o Ca34SO4.2H2O foi obtido por reação química entre o Ca(OH2 e solução de H2(34SO4, realizada sob agitação lenta. O ácido foi produzido por cromatografia de troca iônica, utilizando resina catiônica Dowex 50WX8 e solução eluente de Na2(34SO4. Após a precipitação foi separado o precipitado e realizada a secagem em estufa ventilada à temperatura de 60ºC. Nos testes, a partir de 2,2 L de H2SO4 0,2 mol L-1 e 33,6 g de Ca(OH2, foram produzidos em média 73,7 ± 0,6 g de Ca34SO4.2H2O representando um rendimento médio de 94,6 ± 0,8%, com pureza de 98%. A partir do Ca34SO4.2H2O na presença de NaPO3, em linha de alto vácuo, obteve-se o gás 34SO2 utilizado para a determinação isotópica do S no espectrômetro de massas ATLAS-MAT modelo CH-4.

(Solid + liquid) isothermal evaporation phase equilibria in the aqueous ternary system (Li{sub 2}SO{sub 4} + MgSO{sub 4} + H{sub 2}O) at T = 308.15 K

Energy Technology Data Exchange (ETDEWEB)

Wang Shiqiang [Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, Xining 810008 (China); Graduate University of Chinese Academy of Sciences, Beijing 100039 (China); Deng Tianlong [Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, Xining 810008 (China); College of Materials, Chemistry and Chemical Engineering, Chengdu University Technology, Chengdu 610059 (China)], E-mail: dtl@cdut.edu.cn

2008-06-15

The solubility and the density in the aqueous ternary system (Li{sub 2}SO{sub 4} + MgSO{sub 4} + H{sub 2}O) at T = 308.15 K were determined by the isothermal evaporation. Our experimental results permitted the construction of the phase diagram and the plot of density against composition. It was found that there is one eutectic point for (Li{sub 2}SO{sub 4} . H{sub 2}O + MgSO{sub 4} . 7H{sub 2}O), two univariant curves, and two crystallization regions corresponding to lithium sulphate monohydrate (Li{sub 2}SO{sub 4} . H{sub 2}O) and epsomite (MgSO{sub 4} . 7H{sub 2}O). The system belongs to a simple co-saturated type, and neither double salts nor solid solution was found. Based on the Pitzer ion-interaction model and its extended HW models of aqueous electrolyte solution, the solubility of the ternary system at T = 308.15 K has been calculated. The predicted solubility agrees well with the experimental values.

Prediction models of mechanical properties for pet-mortar composite in sodium sulphateaggressive mediums

Directory of Open Access Journals (Sweden)

Kazi Tani Nabil

2018-01-01

Full Text Available In this research, an investigation was carried out on the effect of sodium sulphate attack on the durability of composites produced with waste polyethylene terephthalate (PET. Experiments were accomplished on limestone sand and cement mortars where the blended Portland cement was partially replaced by various volume fractions of waste PET particles (6%, 12% and 17%. The test solutions used to supply the sulphate ions and cations were 5%sodium sulphate solution. Compressive strengths measured on specimens were used to assess the changes in the mechanical properties of PET-mortars exposed to sulphate attack at different ages, mainly the Young modulus of elasticity. Based on experimental compressive tests on PETMortar composite specimens and there densities, the evolution of Young modulus of elasticity has been analyzed in accordance with normative models given by (ACI-318 and (BS-8110 codes of practice. In addition, a comparative study has been carried out for corrosion resistance coefficients K of unmodified mortar to those modified with waste PET particles. It can be noticed that, for the composite immersed in a corrosive Na2SO4 solution, the corrosion resistance coefficients decrease with the increase of the immersion period. The corrosion sulphate resistance K based on Young modulus before and after immersion of PET-mortar composites is better than that of the control mortar. Therefore, for safety considerations of PET-mortar composites use, ACI 318 is recommended code for design and investigation works. Also, it can be concluded that adding waste PET by volume fractions (6%, 12% and 17% to blend Portland cement renders this cement more resistant to the sodium sulphate aggressive medium. Therefore, composites materials based waste PET aare often presented as the materials of the future because of their potential for innovation and the advantages they offer. In fact, using waste PET as cement substitutes reduces the energy consumption. These

Review on Material Synthesis and Characterization of Sodium (Na) Super-Ionic Conductor (NASICON)

Science.gov (United States)

Kimpa, M. I.; Mayzan, M. Z. H.; Yabagi, J. A.; Nmaya, M. M.; Isah, K. U.; Agam, M. A.

2018-04-01

Sodium (Na) Super Ionic Conductor (NASICON) has general formula Na1+ x Zr2P3- xSi x O12 (0 ≤x ≤ 3) derived from its parent compound, sodium zirconium phosphate NaZr2(PO4)3 (NZP) which belong to a rhombohedral crystal structure. This material consists of three-dimensional structure with interesting features such as low thermal expansion coefficient, thermal stability, gas sensor and nuclear waste immobilization that make it viable for industrial applications. Current study presents comprehensive studies on the synthesis and essential characteristics required to understand the theory behind the mechanism that justifies the study of NASICON structure and its application such as lithium ion rechargeable battery, gas sensor, and nuclear waste immobilization and so on.

Ion conductivity and phase transitions in the Na3Sc2(PO4)3 - NaGe2(PO4)3 system

International Nuclear Information System (INIS)

Nogaj, A.S.

2002-01-01

Influence of heteropolyvalent substitution on dipole ordering of sodium-scandium phosphate, as well as on ion conductivity and phase transitions in the system Na 3 Sc 2 (PO 4 ) 3 - NaGe 2 (PO 4 ) 3 , was studied using the methods of solid phase synthesis, X-ray diffraction, laser spectroscopy and measurement of electric conductivity. Boundaries of the dipole-ordered and superionic phases existence ranges in the given system were identified. It is shown that expansion of the dipole-ordered phase existence range with increase in substituent cation concentration is characteristic of the phase on the basis of α-Na 3 Sc 2 (PO 4 ) 3 [ru

Growth of marine yeast on different strength of stress solutes

Digital Repository Service at National Institute of Oceanography (India)

Gupta, R.

tested against the stress solutes NaCl (0-16%), potassium chloride (KCl) and sodium sulphate (Na sub(2) SO sub(4)) at 0.4%, 4% and 8% concentrations. D. hansenii and D. marama were the most versatile isolates exhibiting excellent growth in all...

Electrochemical properties of a new nanocrystalline NaMn{sub 2}O{sub 4} cathode for rechargeable sodium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Datta, Moni Kanchan, E-mail: mkd16@pitt.edu [Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Center for Complex Engineered Multifunctional Materials, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Kuruba, Ramalinga [Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Jampani, Prashanth H. [Chemical and Petroleum Engineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Chung, Sung Jae [Mechanical Engineering and Materials Science, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Saha, Partha [Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Epur, Rigved [Mechanical Engineering and Materials Science, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Kadakia, Karan; Patel, Prasad [Chemical and Petroleum Engineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Gattu, Bharat [Mechanical Engineering and Materials Science, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Manivannan, Ayyakkannu [US Department of Energy, National Energy Technology Laboratory, Morgantown, WV 26507 (United States); Kumta, Prashant N., E-mail: pkumta@pitt.edu [Bioengineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Center for Complex Engineered Multifunctional Materials, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Chemical and Petroleum Engineering, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); Mechanical Engineering and Materials Science, Swanson School of Engineering, University of Pittsburgh, PA 15261 (United States); School of Dental Medicine, University of Pittsburgh, PA 15261 (United States)

2014-10-15

Highlights: • Nanocrystalline NaMn{sub 2}O{sub 4} exhibiting a new crystalline form has been synthesized by high energy mechanical milling. • Mechanical milling for 20 h directly results in nanocrystalline NaMn{sub 2}O{sub 4}. • Thermally treated oxide shows ∼95 mAh/g capacity in the 2–4.5 V window. • Capacities from ∼75 to 95 mAh/g obtained with varying voltage windows. • Oxide exhibits 0.3%/cycle fade in capacity when cycled in the 2–4 V window. - Abstract: Nanocrystalline NaMn{sub 2}O{sub 4} with a crystallite size of ∼8–10 nm exhibiting a new close packed hexagonal crystalline form, different from the known stable orthorhombic (Pbam or Pmnm symmetry) or monoclinic structures common to the Na–Mn–O system, has been synthesized by a high energy mechano-chemical milling process (HEMM) using Na{sub 2}O{sub 2} and Mn{sub 2}O{sub 3} as starting materials. The newly synthesized structure of NaMn{sub 2}O{sub 4} has been studied as a cathode for sodium ion rechargeable batteries. The HEMM derived NaMn{sub 2}O{sub 4} shows a 1st cycle discharge capacity ∼75 mAh/g, ∼86 mAh/g and ∼95 mAh/g when cycled at a rate of ∼40 mA/g in the potential window ∼2.0–4.0 V, ∼2–4.2 V and ∼2–4.5 V, respectively. The nanostructured NaMn{sub 2}O{sub 4} shows a fade in capacity of 0.3% per cycle and a moderate rate capability when cycled in the potential window 2–4 V. However, electrolyte decomposition occurring during charging of the electrode above ∼3.8 V needs to be resolved in order utilize the full capacity of NaMn{sub 2}O{sub 4} as well as improve the stability of the electrode.

Pin Hole Discharge Creation in Na2SO4 Water Solutions

Directory of Open Access Journals (Sweden)

Lucie Hlavatá

2013-01-01

Full Text Available This work deals with the diaphragm discharge generated in water solutions containing Na2SO4 as a supporting electrolyte. The solution conductivity was varied in the range of 270 ÷ 750 µScm-1. The batch plasma reactor with volume of 100 ml was divided into two electrode spaces by the Shapal-MTM ceramics dielectric barrier with a pin-hole (diameter of 0.6 mm. Three variable barrier thicknesses (0.3; 0.7 and 1.5 mm and non-pulsed DC voltage up to 2 kV were used for the discharge creation. Each of the current–voltage characteristic can be divided into three parts: electrolysis, bubble formation and discharge operation. The experimental results showed that the discharge ignition moment in the pin-hole was significantly dependent on the dielectric diaphragm thickness. Breakdown voltage increases with the increase of the dielectric barrier thickness.

Molecular Surface of JZTX-V (β-Theraphotoxin-Cj2a Interacting with Voltage-Gated Sodium Channel Subtype NaV1.4

Directory of Open Access Journals (Sweden)

Ji Luo

2014-07-01

Full Text Available Voltage-gated sodium channels (VGSCs; NaV1.1–NaV1.9 have been proven to be critical in controlling the function of excitable cells, and human genetic evidence shows that aberrant function of these channels causes channelopathies, including epilepsy, arrhythmia, paralytic myotonia, and pain. The effects of peptide toxins, especially those isolated from spider venom, have shed light on the structure–function relationship of these channels. However, most of these toxins have not been analyzed in detail. In particular, the bioactive faces of these toxins have not been determined. Jingzhaotoxin (JZTX-V (also known as β-theraphotoxin-Cj2a is a 29-amino acid peptide toxin isolated from the venom of the spider Chilobrachys jingzhao. JZTX-V adopts an inhibitory cysteine knot (ICK motif and has an inhibitory effect on voltage-gated sodium and potassium channels. Previous experiments have shown that JZTX-V has an inhibitory effect on TTX-S and TTX-R sodium currents on rat DRG cells with IC50 values of 27.6 and 30.2 nM, respectively, and is able to shift the activation and inactivation curves to the depolarizing and the hyperpolarizing direction, respectively. Here, we show that JZTX-V has a much stronger inhibitory effect on NaV1.4, the isoform of voltage-gated sodium channels predominantly expressed in skeletal muscle cells, with an IC50 value of 5.12 nM, compared with IC50 values of 61.7–2700 nM for other heterologously expressed NaV1 subtypes. Furthermore, we investigated the bioactive surface of JZTX-V by alanine-scanning the effect of toxin on NaV1.4 and demonstrate that the bioactive face of JZTX-V is composed of three hydrophobic (W5, M6, and W7 and two cationic (R20 and K22 residues. Our results establish that, consistent with previous assumptions, JZTX-V is a Janus-faced toxin which may be a useful tool for the further investigation of the structure and function of sodium channels.

Pitting corrosion of Al and Al-Cu alloys by ClO4- ions in neutral sulphate solutions

International Nuclear Information System (INIS)

Amin, Mohammed A.; Abd El Rehim, Sayed S.; Moussa, S.O.; Ellithy, Abdallah S.

2008-01-01

The influence of various concentrations of NaClO 4 , as a pitting corrosion agent, on the corrosion behaviour of pure Al, and two Al-Cu alloys, namely (Al + 2.5 wt% Cu) and (Al + 7 wt% Cu) alloys in 1.0 M Na 2 SO 4 solution was investigated by potentiodynamic polarization and potentiostatic techniques at 25 deg. C. Measurements were conducted under the influence of various experimental conditions, complemented by ex situ energy dispersive X-ray (EDX) and scanning electron microscopy (SEM) examinations of the electrode surface. In free perchlorate sulphate solutions, for the three Al samples, the anodic polarization exhibits an active/passive transition. The active dissolution region involves an anodic peak (peak A) which is assigned to the formation of Al 2 O 3 passive film on the electrode surface. The passive region extends up to 1500 mV with almost constant current density (j pass ) without exhibiting a critical breakdown potential or showing any evidence of pitting attack. For the three Al samples, addition of ClO 4 - ions to the sulphate solution stimulates their active anodic dissolution and tends to induce pitting corrosion within the oxide passive region. Pitting corrosion was confirmed by SEM examination of the electrode surface. The pitting potential decreases with increasing ClO 4 - ion concentration indicating a decrease in pitting corrosion resistance. The susceptibility of the three Al samples towards pitting corrosion decreases in the order: Al > (Al + 2.5 wt% Cu) alloy > (Al + 7 wt% Cu) alloy. Potentiostatic measurements showed that the rate of pitting initiation increases with increasing ClO 4 - ion concentration and applied step anodic potential, while it decreases with increasing %Cu in the Al samples. The inhibitive effect of SO 4 2- ions was also discussed

Crystal structure of NaPr(SeO4)2

International Nuclear Information System (INIS)

Ovanisyan, S.M.; Iskhakova, L.D.

1989-01-01

NaPr(SeO 4 ) 2 structure is decoded (autodiffractometer CAD-4). Triclinic cell parameters are as follows: a=6.639(2), b=7.118(1), c=7.36(1) A, α=99.16(2) deg, β=96.93(2) deg, γ=89.77 (3) deg, p.gr. P1-bar, Z=2. Structure is of carcass type, built on CaSO 4 anhydride structure base with 2Ca→TR 3+ +Na + -type ordered substitution. Structural comparative crystallochemical analysis of anhydride and NaPr(SeO 4 ) 2 and NaNd(SO 4 ) 2 isostructural double salts is carried out

Thermal transformation of synthetic borax, Na2[B4O5(OH)4]x8H2O

International Nuclear Information System (INIS)

Abdullaev, G.K.

1981-01-01

Using the methods of high temperature roentgenography and derivatography thermal transformation of synthetic borax is studied. It is established that borax dehydration proceeds in four stages (50-80, 80-100, 100-150 and 150-500 deg C) with the formation of three intermediate crystalline hydrate forms (one stable and two unstable) and one final stable crystalline phase. The stable crystalline phases correspond to synthetic tincalconite Na 2 [B 4 O 5 (OH) 4 ]x3H 2 O and sodium tetraborate Na 2 B 4 O 7 . Thermal transformation of borax into tincalconite and sodium tetraborate is explained on the basis of their crystal structures [ru

Alkaline sodium borohydride gel as a hydrogen source for PEMFC or an energy carrier for NaBH 4-air battery

Science.gov (United States)

Liu, B. H.; Li, Z. P.; Chen, L. L.

In this preliminary study, we tried to use sodium polyacrylate as the super absorbent polymer to form alkaline NaBH 4 gel and explored its possibilities for borohydride hydrolysis and borohydride electro-oxidation. It was found that the absorption capacity of sodium polyacrylate decreased with increasing NaBH 4 concentration. The formed gel was rather stable in the sealed vessel but tended to slowly decompose in open air. Hydrogen generation from the gel was carried out using CoCl 2 catalyst precursor solutions. Hydrogen generation rate from the alkaline NaBH 4 gel was found to be higher and impurities in hydrogen were less than that from the alkaline NaBH 4 solution. The NaBH 4 gel also successfully powered a NaBH 4-air battery.

Design of Diclofenac Sodium Indicator Strips Using Polystyrene (PS and Polymethylmethacrylate (PMMA for Detection of Diclofenac Sodium in Traditional Pain Relief Herbal Medicines

Directory of Open Access Journals (Sweden)

Ibrahim Dalli

2017-04-01

Full Text Available Diclofenac sodium is one of analgesic which is often added to traditional pain relief herbal medicines to enhance the effects. One of qualititative method that is easy, efficient and simple testing is an indicator strip. Indicator strip based Polystyrene (PS and Polymethylmethacrylate (PMMA was made for the examination of diclofenac sodium that were misused as a drug chemical compound in traditional pain relief herbal medicine. Strip indikator was made by reagent blending method with specific reagents used, namely, copper sulphate (CuSO4, ferric chloride (FeCl3 and vanillin sulphate. The working principle of the indicator strip in detecting the presence of diclofenac sodium in herbal medicine is with the occurrence of a color reaction. The concentration of PS and PMMA was made in a variation of 5%, 7.5% and 10%, and the mixture of PS: PMMA 1: 5 and 1: 6 concecutively with a ratio of solvent: reactant 6: 4; 7: 3 and 8:2. The test results showed that the best indicator strip is PMMA-CuSO4 5% (7: 3, PMMA-FeCl3 5% (7: 3 and PMMA-Vanillin sulphate 7.5% (7: 3. The detection limit and stability of the strip indicators PMMA-CuSO4 5% (7: 3 are at 50 ppm and is stable up to 29 weeks, PMMA-FeCl3 5% (7: 3 has a detection limit 12,500 ppm and is stable up to 29 weeks, and PMMA-vanillin sulphate 7,5% (7: 3 has a detection limit 500 ppm and is stable up to 29 weeks. The results showed that the indicator strip can be used as an alternative method to detect diclofenac sodium in herbal medicine and finally controlling addition of chemicals in to herbal medicine.

Study of fatigue crack nucleation in 12% chromium stainless steel in sulphate and phosphate solutions

International Nuclear Information System (INIS)

Shalaby, H.M.; Begley, J.A.; Macdonald, D.D.

1989-01-01

The morphology of fatigue crack nucleation has been studied in 12%Cr stainless steel at a single stress level of 448 MN m -2 in deaerated H 2 SO 4 -Na 2 SO 4 -NaOH ([SO 4 2- ] = 0.01M and 1M) and in H 3 PO 4 -NaOH ([PO 4 3- ] = 0.01M and 1M) solutions at pH 2, 7 and 10 at 100 0 C. In sulphate solutions at pH 2, the specimen suffered overall surface attack without the initiation of microcracks. The surface attack intensified at the prior austenite grain boundaries, martensite platelet boundaries, and non-metallic inclusions. In contrast, cracks initiated transgranularly in sulphate solutions at pH 7 and 10 with the development of selective attack at crack sites at later stages in the fatigue life. This attack was ascribed to local acidification as a result of hydrolysis of corrosion products extruded from inside the cracks. Long cracks with crack branching and debonded zones were observed in all phosphate solutions, except in 0.01M phosphate solution at pH 7. In this latter environment, short intrusion-extrusion microcracks were observed. This difference in behaviour was attributed to changes in the characteristics of the passive film as influenced by the local environmental conditions, mechanical rupture by plastic deformation, and electrochemical differences at the metal surface. (author)

Layered P2-Na 2/3 Co 1/2 Ti 1/2 O 2 as a high-performance cathode material for sodium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Sabi, Noha; Doubaji, Siham; Hashimoto, Kazuki; Komaba, Shinichi; Amine, Khalil; Solhy, Abderrahim; Manoun, Bouchaib; Bilal, Essaid; Saadoune, Ismael

2017-02-01

Layered oxides are regarded as promising cathode materials for sodium-ion batteries. We present Na2/3Co1/2Ti1/2O2 as a potential new cathode material for sodium-ion batteries. The crystal features and morphology of the pristine powder were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The cathode material is evaluated in galvanostatic charge-discharge and galvanostatic intermittent titration tests, as well as ex-situ X-ray diffraction analysis. Synthesized by a high-temperature solid state reaction, Na2/3Co1/2Ti1/2O2 crystallizes in P2-type structure with P6(3)/mmc space group. The material presents reversible electrochemical behavior and delivers a specific discharge capacity of 100 mAh g(-1) when tested in Na half cells between 2.0 and 4.2 V (vs. Na+/Na), with capacity retention of 98% after 50 cycles. Furthermore, the electrochemical cycling of this titanium-containing material evidenced a reduction of the potential jumps recorded in the NaxCoO2 parent phase, revealing a positive impact of Ti substitution for Co. The ex-situ XRD measurements confirmed the reversibility and stability of the material. No structural changes were observed in the XRD patterns, and the P2-type structure was stable during the charge/discharge process between 2.0 and 4.2 V vs. Na+/Na. These outcomes will contribute to the progress of developing low cost electrode materials for sodium-ion batteries. (C) 2017 Elsevier B.V. All rights reserved.

The Cs2SO4-Ce2(SO4)3-H2SO4-H2O system at 150 and 200 deg C

International Nuclear Information System (INIS)

Bondar', S.A.; Belokoskov, V.I.; Trofimov, G.V.

1982-01-01

Solubility in the system Cs 2 SO 4 -Ce 2 (SO 4 ) 3 -H 2 SO 4 -H 2 O using the isothermal method at 150 and 200 deg C at molar ratios Cs 2 SO 4 :Ce 2 (SO 4 ) 3 =1:5 and conditions of sulfate crystallization Cs 2 SO 4 xCe 2 (SO 4 ) 3 , Ce 2 (SO 4 ) 3 x0.5H 2 SO 4 xnH 2 O (n=2-3) and Ce 2 (SO 4 ) 3 x3H 2 SO 4 are determined. Double sulfate Cs 2 SO 4 xCe 2 (SO 4 ) 3 is studied using the methods of crystallooptical, thermal, X-ray phase analyses and IR spectroscopy

The impact of sulphate and magnesium on chloride binding in Portland cement paste

Energy Technology Data Exchange (ETDEWEB)

De Weerdt, K., E-mail: klaartje.d.weerdt@ntnu.no [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway); SINTEF Building and Infrastructure, Trondheim (Norway); Orsáková, D. [Department of Civil Engineering, Technical University of Brno, Brno (Czech Republic); Geiker, M.R. [Department of Structural Engineering, Norwegian University of science and Technology, Trondheim (Norway)

2014-11-15

The effect of magnesium and sulphate present in sea water on chloride binding in Portland cement paste was investigated. Ground well hydrated cement paste was exposed to MgCl{sub 2}, NaCl, NaCl + MgCl{sub 2}, MgSO{sub 4} + MgCl{sub 2} and artificial sea water solutions with a range of concentrations at 20 °C. Chloride binding isotherms are determined and pH of the solutions were measured. A selection of samples was examined by SEM-EDS to identify phase changes upon exposure. The experimental data were compared with calculations of a thermodynamic model. Chloride binding from sea water was similar to chloride binding for NaCl solutions. The magnesium content in the sea water lead to a slight decrease in pH, but this did not result in a notable increase in chloride binding. The sulphate present in sea water reduces both chloride binding in C–S–H and AFm phases, as the C–S–H incorporates more sulphates instead of chlorides, and part of the AFm phases converts to ettringite.

Cs2SO4-Pr2(SO4)3-H2O and NiSO4-Pr2(SO4)3-H2O systems at 75 deg C

International Nuclear Information System (INIS)

Onishchenko, M.K.; Skorikov, V.M.; Shevchuk, V.G.; AN SSSR, Moscow. Inst. Obshchej i Neorganicheskoj Khimii)

1979-01-01

To investigate physico-chemical properties of equilibrium saturated solutions and to elucidate the chemical changes under way, the aqueous systems of cesium, nickel and praseodymium (3) sulfates are studied. The method of isothermal saturation of salts at 75 deg C is used. It has been found that in the system Cs 2 SO 4 -Pr 2 (SO 4 ) 3 -H 2 O in a wide concentration range the soluble binary salt Cs 2 SO 4 xPr 2 (SO 4 ) 3 csytallizes in a congruent way. For the system NiSO 4 -Pr 2 (SO 4 ) 3 -H 2 O a solubility curve of the eutonic type is obtained, there being no chemical interaction between the components. The solubility isotherms for the system are given

Alkaline sodium borohydride gel as a hydrogen source for PEMFC or an energy carrier for NaBH{sub 4}-air battery

Energy Technology Data Exchange (ETDEWEB)

Liu, B.H. [Department of Materials and Engineering, Zhejiang University (China); Li, Z.P.; Chen, L.L. [Department of Chemical and Biochemical Engineering, Zhejiang University, Hangzhou 310027 (China)

2008-05-15

In this preliminary study, we tried to use sodium polyacrylate as the super absorbent polymer to form alkaline NaBH{sub 4} gel and explored its possibilities for borohydride hydrolysis and borohydride electro-oxidation. It was found that the absorption capacity of sodium polyacrylate decreased with increasing NaBH{sub 4} concentration. The formed gel was rather stable in the sealed vessel but tended to slowly decompose in open air. Hydrogen generation from the gel was carried out using CoCl{sub 2} catalyst precursor solutions. Hydrogen generation rate from the alkaline NaBH{sub 4} gel was found to be higher and impurities in hydrogen were less than that from the alkaline NaBH{sub 4} solution. The NaBH{sub 4} gel also successfully powered a NaBH{sub 4}-air battery. (author)

Synthesis of specifically deuterated pregnanolone and pregnanediol sulphates for metabolic studies in pregant women

International Nuclear Information System (INIS)

Baillie, T.A.; Herz, J.E.; Anderson, R.A.; Sjovall, J.

1975-01-01

A series of specifically deuterated isomers of pregnanolone sulphate and pregnanediol mono- and disulphate have been synthesized for use in a study of the formation and metabolism of C 21 -steroid sulphates in the plasma of pregnant women. Hecogenin, the starting material for the synthesis, was equilibrated with NaO 2 H- 2 H 2 O and the resulting 11,11- 2 H 2 derivative converted directly to its tosylhydrazone. Reduction with sodium borohydride and degradation of the sapogenin side-chain gave 3β-hydroxy-5α-[11,11- 2 H 2 ] pregn-16-en-20-one (isotopic purity 91.6%). Further deuterium atoms were introduced in the 3α and 3α,20β positions by reductions with sodium borodeuteride and lithium aluminum deuteride, respectively. These reactions led to 3β-hydroxy-5α-[3α,11,11- 2 H 3 ] pregnan-20-one (isotopic purity 87.2%) and 5α-[3α,11,11,20β- 2 H 4 ] pregnane-3β,20α-diol (isotopic purity 83.9%). Steroids possessing the less readily accessible 3α-hydroxy-5α-[3β- 2 H] configuration were obtained, without loss of label, by epimerization of the 3β isomers. Pregnanolone sulphates and pregnanediol disulphates were prepared directly from the free alcohols, while the pregnanediol 3-monosulphates were synthesized from the appropriate pregnanediol 20-monoacetate derivatives

Hydrolysis of Rice Straw Pretreated by Na2SO3 Over Fe-resin/NaCl

Directory of Open Access Journals (Sweden)

YANG Hui

2017-05-01

Full Text Available To increase the conversion of rice straw(RS and the yield of products, we employed three methods, which were ultrasonic wave, steam explosion and Na2SO3 pretreatment to pretreat RS(the treated RS noted as CS-RS, ZQ-RS and Na2SO3-RS, respectively and found that Na2SO3 treatment was the best pretreatment method based on XRD, SEM, elemental analysis and content of cellulose, hemicellulose and lignin. The conversion of Na2SO3-RS and the yield of total reducing sugar(TRS and levulinic acid(LA were 97.3%, 29.6% and 13.5%, respectively by 10% Fe-resin in 3.3% NaCl solution under 200 ℃.

Pilot scale-SO{sub 2} control by dry sodium bicarbonate injection and an electrostatic precipitator

Energy Technology Data Exchange (ETDEWEB)

Pliat, M.J.; Wilder, J.M. [University of Washington, Seattle, WA (United States). Dept. of Civil & Environmental Engineering

2007-10-15

A 500 actual cubic feet gas per minute (acfm) pilot-scale SO{sub 2} control study was undertaken to investigate flue gas desulfurization (FGD) by dry sodium sorbents in 400{sup o}F (204.5{sup o}C) flue gases emitted from a coal fired boiler with flue gas concentrations between 350 and 2500 ppm SO{sub 2}. Powdered sodium alkaline reagents were injected into the hot flue gas downstream of the air preheater and the spent reagents were collected using an electrostatic precipitator. Three different sorbents were used: processed sodium bicarbonate of two particle sizes; solution mined sodium bicarbonate, and processed sodium sesquicarbonate. SO{sub 2} concentrations were measured upstream of the reagent injection, 25-ft (7.62 m) downstream of the injection point, and downstream of the electrostatic precipitator. SO{sub 2} collection efficiencies ranged from 40 to 80% using sodium bicarbonate stoichiometric ratios from 0.5 to 3.0. Much of the in-duct SO{sub 2} removal occurred during the first second of reagent reaction time, indicating that the sulfur dioxide-sodium reaction rates may be faster than have been measured for fixed bed measurements reported in the literature.

Glucose-assisted synthesis of Na3V2(PO4)3/C composite as an electrode material for high-performance sodium-ion batteries

Science.gov (United States)

Li, Guangqiang; Jiang, Danlu; Wang, Hui; Lan, Xinzheng; Zhong, Honghai; Jiang, Yang

2014-11-01

A novel electrode material for sodium-ion batteries (NIBs), Na3V2(PO4)3 with a rhombohedral, Na+ superionic conductor (NASICON)-type structure, was synthesised via a solid-state carbon-thermal reduction reaction assisted by mechanochemical activation. Electron microscopy analysis showed that the synthesised Na3V2(PO4)3 particles had an average size of 300 nm, being coated with a uniform layer of carbon 3 nm in thickness. As a cathode material, Na3V2(PO4)3/C exhibited an initial specific discharge capacity of 98.17 mAh g-1 at 0.1C for potentials ranging from 2.5 to 3.8 V. This was owing to the V3+/V4+ redox couple, which corresponded to the two-phase transition between Na3V2(PO4)3 and NaV2(PO4)3. The cathode lost 4.92% of its discharge specific capacity after 50 cycles. As an anode material, Na3V2(PO4)3/C exhibited an initial specific discharge capacity of 63.2 mAh g-1 at 0.1C for potentials ranging from 1.0 to 2.5 V. This was owing to the V2+/V3+ redox couple, which corresponded to the two-phase transition between Na3V2(PO4)3 and Na4V2(PO4)3. The anode lost approximately 5.41% of its discharge specific capacity after 50 cycles. The three-dimensional channel structure of NaV2(PO4)3 and the changes induced in its lattice parameters during the charge/discharge processes were simulated on the basis of density functional theory.

Study of ZrO2-H2SO4-(NH4)2SO4(NH4Cl)-H2O systems

International Nuclear Information System (INIS)

Motov, D.L.; Sozinova, Yu.P.; Rys'kina, M.P.

1988-01-01

Regions of formation, composition and solubility of ammonium sulfatozirconates (ASZ) in ZrO 2 -H 2 SO 4 -(NH 4 ) 2 SO 4 (NH 4 Cl)-H 2 O systems at 25 and 75 deg C are studied by the isothermal method. Five ASZ: (NH 4 ) 2 Zr(OH) 2 (SO 4 ) 2 , NH 4 ZrOH(SO 4 ) 2 xH 2 O, NH 4 ZrO 0.5 (OH) 2 SO 4 x1.5H 2 O, (NH 4 ) 2 Zr(SO 4 ) 3 x2H 2 O, (NH 4 ) 4 Zr(SO 4 ) 4 x4H 2 O are detected, their properties are investigated. Main sulfates are new compounds never described ealier

Molecular structure of dextran sulphate sodium in aqueous environment

Science.gov (United States)

Yu, Miao; Every, Hayley A.; Jiskoot, Wim; Witkamp, Geert-Jan; Buijs, Wim

2018-03-01

Here we propose a 3D-molecular structural model for dextran sulphate sodium (DSS) in a neutral aqueous environment based on the results of a molecular modelling study. The DSS structure is dominated by the stereochemistry of the 1,6-linked α-glucose units and the presence of two sulphate groups on each α-glucose unit. The structure of DSS can be best described as a helix with various patterns of di-sulphate substitution on the glucose rings. The presence of a side chain does not alter the 3D-structure of the linear main chain much, but affects the overall spatial dimension of the polymer. The simulated polymers have a diameter similar to or in some cases even larger than model α-hemolysin nano-pores for macromolecule transport in many biological processes, indicating a size-limited translocation through such pores. All results of the molecular modelling study are in line with previously reported experimental data. This study establishes the three-dimensional structure of DSS and summarizes the spatial dimension of the polymer, serving as the basis for a better understanding on the molecular level of DSS-involved electrostatic interaction processes with biological components like proteins and cell pores.

Asymmetric synthesis of allylic sulfonic acids: enantio- and regioselective iridium-catalyzed allylations of Na2SO3.

Science.gov (United States)

Liu, Wei; Zhao, Xiao-ming; Zhang, Hong-bo; Zhang, Liang; Zhao, Ming-zhu

2014-12-15

An enantioselective allylation reaction of allylic carbonates with sodium sulfite (Na2 SO3 ) catalyzed by Ir complex was accomplished, providing allylic sulfonic acids in good to excellent yields with a high level of enantio- and regioselectivities. (R)-2-Phenyl-2-sulfoacetic acid, a key intermediate for the synthesis of Cefsulodin and Sulbenicillin, was synthesized as well. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Sulphate and chloride aerosols during Holocene and last glacial periods preserved in the Talos Dome Ice Core, a peripheral region of Antarctica

Directory of Open Access Journals (Sweden)

Yoshinori Iizuka

2013-04-01

Full Text Available Antarctic ice cores preserve the record of past aerosols, an important proxy of past atmospheric chemistry. Here we present the aerosol compositions of sulphate and chloride particles in the Talos Dome (TD ice core from the Holocene and Last Glacial Period. We find that the main salt types of both periods are NaCl, Na2SO4 and CaSO4, indicating that TD ice contains relatively abundant sea salt (NaCl from marine primary particles. By evaluating the molar ratio of NaCl to Na2SO4, we show that about half of the sea salt does not undergo sulphatisation during late Holocene. Compared to in inland Antarctica, the lower sulphatisation rate at TD is probably due to relatively little contact between sea salt and sulphuric acid. This low contact rate can be related to a reduced time of reaction for marine-sourced aerosol before reaching TD and/or to a reduced post-depositional effect from the higher accumulation rate at TD. Many sulphate and chloride salts are adhered to silicate minerals. The ratio of sulphate-adhered mineral to particle mass and the corresponding ratio of chloride-adhered mineral both increase with increasing dust concentration. Also, the TD ice appears to contain Ca(NO32 or CaCO3 particles, thus differing from aerosol compositions in inland Antarctica, and indicating the proximity of peripheral regions to marine aerosols.

Hemicelluloses negatively affect lignocellulose crystallinity for high biomass digestibility under NaOH and H2SO4 pretreatments in Miscanthus

Directory of Open Access Journals (Sweden)

Xu Ning

2012-08-01

Full Text Available Abstract Background Lignocellulose is the most abundant biomass on earth. However, biomass recalcitrance has become a major factor affecting biofuel production. Although cellulose crystallinity significantly influences biomass saccharification, little is known about the impact of three major wall polymers on cellulose crystallization. In this study, we selected six typical pairs of Miscanthus samples that presented different cell wall compositions, and then compared their cellulose crystallinity and biomass digestibility after various chemical pretreatments. Results A Miscanthus sample with a high hemicelluloses level was determined to have a relatively low cellulose crystallinity index (CrI and enhanced biomass digestibility at similar rates after pretreatments of NaOH and H2SO4 with three concentrations. By contrast, a Miscanthus sample with a high cellulose or lignin level showed increased CrI and low biomass saccharification, particularly after H2SO4 pretreatment. Correlation analysis revealed that the cellulose CrI negatively affected biomass digestion. Increased hemicelluloses level by 25% or decreased cellulose and lignin contents by 31% and 37% were also found to result in increased hexose yields by 1.3-times to 2.2-times released from enzymatic hydrolysis after NaOH or H2SO4 pretreatments. The findings indicated that hemicelluloses were the dominant and positive factor, whereas cellulose and lignin had synergistic and negative effects on biomass digestibility. Conclusions Using six pairs of Miscanthus samples with different cell wall compositions, hemicelluloses were revealed to be the dominant factor that positively determined biomass digestibility after pretreatments with NaOH or H2SO4 by negatively affecting cellulose crystallinity. The results suggested potential approaches to the genetic modifications of bioenergy crops.

Mechanochemical transformations in Li(Na)AlH4-Li(Na)NH2 systems

International Nuclear Information System (INIS)

Dolotko, Oleksandr; Zhang Haiqiao; Ugurlu, Ozan; Wiench, Jerzy W.; Pruski, Marek; Scott Chumbley, L.; Pecharsky, Vitalij

2007-01-01

Mechanochemical transformations of tetrahydroaluminates and amides of lithium and sodium have been investigated using gas volumetric analysis, X-ray powder diffraction, solid-state nuclear magnetic resonance (NMR) and transmission electron microscopy. In a transformation of LiAlH 4 and LiNH 2 taken in an 1:1 molar ratio, the amount of released hydrogen (6.6 wt.% after 30 min ball milling) was higher than in any known one pot mechanochemical process involving a hydrogen-containing solid. A total of 4.3 wt.% of hydrogen is released by the NaAlH 4 -NaNH 2 system after 60 min ball milling; and 5.2 wt.% H 2 is released when LiAlH 4 and NaNH 2 or NaAlH 4 and LiNH 2 are ball milled for 90 min and 120 min, respectively. All transformations proceed at room temperature. The mechanism of the overall transformation MAlH 4 (s) + MNH 2 (s) → 2MH(s) + AlN(s) + 2H 2 (g) was identified based on detailed spectroscopic analysis of the intermediate (M 3 AlH 6 ) and final products of the ball milling process

Identification of nitrates and sulphates with dynamic SIMS

International Nuclear Information System (INIS)

Fichtner, M.; Goschnick, J.; Ache, H.J.

1994-01-01

Sputter conditions are outlined for the identification of chemically sensitive salt compounds, such as nitrates or sulphates, in multicomponent samples of environmental origin using dynamic SIMS for depth-profiling with nanoscale resolution. Sputtering with 1 keV Xe + has been found to be appropriate to enable both the emission of decisive molecular ions with enough intensity as well as substantial erosion for depth-profiling. The use of heavy projectiles reduces the destruction of chemical compounds in the surface of the solid and enhances sensitivity and identification power of SIMS. The method was applied to the analysis of urban outdoor aerosol particles to investigate the conversion of NaCl into Na 2 SO 4 or NaNO 3 by the interaction of sea salt aerosol with the atmospheric pollutants NO x and SO x . Only NaNO 3 was found in the sea salt fraction. (orig.)

The early and late effects of digoxin treatment on the sodium transport, sodium content and Na+K+- ATPase or erythrocytes.

Science.gov (United States)

Cumberbatch, M; Zareian, K; Davidson, C; Morgan, D B; Swaminathan, R

1981-01-01

1 Erythrocyte sodium content, sodium transport (ouabain sensitive sodium flux Eos, and ouabain sensitive efflux rate constant ERCos) sodium, potassium activated ouabain sensitive adenosine triphosphatase (Na+K+ATPase) and plasma digoxin were measured in patients during acute digitalisation and in patients who were on long-term digoxin treatment. 2 In the six patients who were studied during digitalisation, the ERCos and Na+K+ATPase activity decreased and erythrocyte sodium content increased during days 2-4 treatment, but there was no change in Eos. 3 In 39 patients on long term digoxin therapy (2-119 months) the erythrocyte sodium content was normal, but the erythrocyte Na+K+ATPase activity was higher than the control group. When the results from these 39 patients were divided according to the duration of treatment it was found that the erythrocyte sodium content was higher in patients treated for 2-4 months than in patients treated for longer periods and the erythrocyte Na+K+ATPase activity increased with duration of treatment. In eight patients (duration of treatment greater than 29 months) in whom ERCos and Eos were measured, ERCos and Eos were higher than the control group. 4 The results suggest that the effects of digoxin on erythrocytes which occur during acute digoxin treatment do not persist in the long term. 5 The possible explanation for the higher ERCos, Eos and Na+K+ATPase activity in patients treated with digoxin for more than 2 months is discussed. PMID:6268133

Sodium pyrophosphate enhances iron bioavailability from bouillon cubes fortified with ferric pyrophosphate.

Science.gov (United States)

Cercamondi, Colin I; Duchateau, Guus S M J E; Harika, Rajwinder K; van den Berg, Robin; Murray, Peter; Koppenol, Wieneke P; Zeder, Christophe; Zimmermann, Michael B; Moretti, Diego

2016-08-01

Fe fortification of centrally manufactured and frequently consumed condiments such as bouillon cubes could help prevent Fe deficiency in developing countries. However, Fe compounds that do not cause sensory changes in the fortified product, such as ferric pyrophosphate (FePP), exhibit low absorption in humans. Tetra sodium pyrophosphate (NaPP) can form soluble complexes with Fe, which could increase Fe bioavailability. Therefore, the aim of this study was to investigate Fe bioavailability from bouillon cubes fortified with either FePP only, FePP+NaPP, ferrous sulphate (FeSO4) only, or FeSO4+NaPP. We first conducted in vitro studies using a protocol of simulated digestion to assess the dialysable and ionic Fe, and the cellular ferritin response in a Caco-2 cell model. Second, Fe absorption from bouillon prepared from intrinsically labelled cubes (2·5 mg stable Fe isotopes/cube) was assessed in twenty-four Fe-deficient women, by measuring Fe incorporation into erythrocytes 2 weeks after consumption. Fe bioavailability in humans increased by 46 % (P<0·005) when comparing bouillons fortified with FePP only (4·4 %) and bouillons fortified with FePP+NaPP (6·4 %). Fe absorption from bouillons fortified with FeSO4 only and with FeSO4+NaPP was 33·8 and 27·8 %, respectively (NS). The outcome from the human study is in agreement with the dialysable Fe from the in vitro experiments. Our findings suggest that the addition of NaPP could be a promising strategy to increase Fe absorption from FePP-fortified bouillon cubes, and if confirmed by further research, for other fortified foods with complex food matrices as well.

Thermal expansion studies on UMoO5, UMoO6, Na2U(MoO4)3 and Na4U(MoO4)4

International Nuclear Information System (INIS)

Keskar, Meera; Dahale, N.D.; Krishnan, K.

2009-01-01

In the present work, thermal expansion behavior of lower valent sodium uranium molybdates, i.e., Na 2 U(MoO 4 ) 3 and Na 4 U(MoO 4 ) 4 were studied under vacuum in the temperature range of 298-873 K using high temperature X-ray diffractometry (HTXRD). Expansion behaviors of UMoO 5 and UMoO 6 were also studied in vacuum from 298 to 873 K and 773 K, respectively. UMoO 5 was synthesized by reacting UO 2 with MoO 3 in equi-molar proportion in evacuated sealed quartz ampoule at 1173 K for 14 h. Na 2 U(MoO 4 ) 3 and Na 4 U(MoO 4 ) 4 were prepared by reacting UMoO 5 and MoO 3 with 1 and 2 moles of Na 2 MoO 4 , respectively, at 873 K in evacuated sealed quartz ampoule. XRD data of UMoO 5 and UMoO 6 were indexed on orthorhombic and monoclinic systems, respectively, whereas, the data of Na 2 U(MoO 4 ) 3 and Na 4 U(MoO 4 ) 4 were indexed on tetragonal system. The lattice parameters and cell volume of all the four compounds, fit into polynomial expression with respect to temperature, showed positive thermal expansion (PTE) up to 873 K.

Characterisation of Ba(OH){sub 2}–Na{sub 2}SO{sub 4}–blast furnace slag cement-like composites for the immobilisation of sulfate bearing nuclear wastes

Energy Technology Data Exchange (ETDEWEB)

Mobasher, Neda; Bernal, Susan A.; Hussain, Oday H. [Immobilisation Science Laboratory, Department of Materials Science and Engineering, The University of Sheffield, Sheffield S1 3JD (United Kingdom); Apperley, David C. [Solid-State NMR Group, Department of Chemistry, Durham University, Durham DH1 3LE (United Kingdom); Kinoshita, Hajime [Immobilisation Science Laboratory, Department of Materials Science and Engineering, The University of Sheffield, Sheffield S1 3JD (United Kingdom); Provis, John L., E-mail: j.provis@sheffield.ac.uk [Immobilisation Science Laboratory, Department of Materials Science and Engineering, The University of Sheffield, Sheffield S1 3JD (United Kingdom)

2014-12-15

Soluble sulfate ions in nuclear waste can have detrimental effects on cementitious wasteforms and disposal facilities based on Portland cement. As an alternative, Ba(OH){sub 2}–Na{sub 2}SO{sub 4}–blast furnace slag composites are studied for immobilisation of sulfate-bearing nuclear wastes. Calcium aluminosilicate hydrate (C–A–S–H) with some barium substitution is the main binder phase, with barium also present in the low solubility salts BaSO{sub 4} and BaCO{sub 3}, along with Ba-substituted calcium sulfoaluminate hydrates, and a hydrotalcite-type layered double hydroxide. This reaction product assemblage indicates that Ba(OH){sub 2} and Na{sub 2}SO{sub 4} act as alkaline activators and control the reaction of the slag in addition to forming insoluble BaSO{sub 4}, and this restricts sulfate availability for further reaction as long as sufficient Ba(OH){sub 2} is added. An increased content of Ba(OH){sub 2} promotes a higher degree of reaction, and the formation of a highly cross-linked C–A–S–H gel. These Ba(OH){sub 2}–Na{sub 2}SO{sub 4}–blast furnace slag composite binders could be effective in the immobilisation of sulfate-bearing nuclear wastes.

Structural Stability and Electronic Properties of Na2C6O6 for a Rechargeable Sodium-ion Battery

Science.gov (United States)

Yamashita, Tomoki; Fujii, Akihiro; Momida, Hiroyoshi; Oguchi, Tamio

2014-03-01

Sodium-ion batteries have been explored as a promising alternative to lithium-ion batteries owing to a significant advantage of a natural abundance of sodium. Recently, it has been reported that disodium rhodizonate, Na2C6O6, exhibit good electrochemical properties and cycle performance as a minor-metal free organic cathode for sodium-ion batteries. However, its crystal structures during discharge/charge cycle still remain unclear. In this work, we theoretically propose feasible crystal structures of Na2+xC6O6 using first principles calculations. A structural phase transition has been found: Na4C6O6 has a different C6O6 packing arrangement from Na2C6O6. Electronic structures of Na2+xC6O6 during discharge/charge cycle are also discussed. Our predictions could be the key to understanding the discharge/charge process of Na2C6O6. Supported by MEXT program ``Elements Strategy Initiative to Form Core Rersearch Center'' (since 2012), MEXT; Ministry of Education Culture, Sports, Science and Technology, Japan.

Nuclear spin phonon relaxation by Raman process in Na{sub 3}H(SO{sub 4}){sub 2} single crystals with the electric-quadrupole-type interaction using {sup 1}H and {sup 23}Na NMR

Energy Technology Data Exchange (ETDEWEB)

Lim, Ae Ran [Department of Science Education, Jeonju University, Jeonju 560-759, Chonbuk (Korea, Republic of)], E-mail: aeranlim@hanmail.net; Shin, Chang Woo [Solid State Analysis Team, Korea Basic Science Institute, Daegu 702-701 (Korea, Republic of)

2008-11-30

Successive phase transitions in a Na{sub 3}H(SO{sub 4}){sub 2} single crystal were found at 296, 513, and 533 K. To investigate the mechanism of the phase transition at 296 K, the {sup 1}H and {sup 23}Na spin-lattice relaxation time and the spin-spin relaxation time of Na{sub 3}H(SO{sub 4}){sub 2} were measured near the phase transition temperature using a FT NMR spectrometer. The spin-lattice relaxation time, T{sub 1}, for {sup 1}H in Na{sub 3}H(SO{sub 4}){sub 2} crystals exhibits a minimum below T{sub C1} (=296 K) indicating the presence of distinct molecular motion governed by the Bloembergen-Purcell-Pound (BPP) theory. Although the results for the {sup 1}H and {sup 23}Na relaxation times provide no evidence of the phase transition at T{sub C1}, the separation of the {sup 23}Na resonance lines changes abruptly at T{sub C1}. The phase transition at 296 K produces a change in the separation of the Na resonance line that is associated with a change in the atomic positions in the vicinity of the Na ions. Also, the nuclear spin-lattice relaxation process in Na{sub 3}H(SO{sub 4}){sub 2} crystals with the electric-quadrupole-type interaction proceed via Raman process. These results are compared with those obtained for other M{sub 3}H(SO{sub 4}){sub 2} (M=K, Rb, and Cs) crystals, which have similar hydrogen-bonded structures.

A frogspawn-inspired hierarchical porous NaTi2(PO4)3-C array for high-rate and long-life aqueous rechargeable sodium batteries

Science.gov (United States)

Zhao, Baidan; Lin, Bo; Zhang, Sen; Deng, Chao

2015-11-01

Hollow micro/nano-arrays have attracted tremendous attention in the field of energy conversion and storage, but such structures usually compromise the volumetric energy density of the electrode materials. Frogspawn consists of a spawn core and a transparent jelly shell organized in a hierarchical porous array, which exhibits superior mechanical strength and high-efficiency oxygen permeability. It can be used as a model for designing a new high-performance electrode material, which has advantages such as a high surface area, fast mass transport and superior durability. Herein, we report a frogspawn-like NaTi2(PO4)3/C array prepared by a facile preform impregnation strategy. The framework is formed by a hollow carbon sphere connected by the NaTi2(PO4)3/C skeleton, and its hollow is filled with the NaTi2(PO4)3 nanospheres. The whole hierarchical porous three-dimensional array copies the structure of a frogspawn. This unique structure not only enables easy electrolyte percolation and fast electron/ion transport, but also enhances the reversible capacity and cycling durability. When it is applied as an anode of the aqueous sodium ion battery, it exhibits favorable high rate capability and superior cycling stability, and retains 89% of the initial capacity after two thousand cycles at 20 C. Moreover, the full cell using the frogspawn-inspired NaTi2(PO4)3-C as the anode and Na0.44MnO2 as the cathode is capable of ultralong cycling up to one thousand cycles at alternate 10 and 60 C, which is among the best of state-of-the-art aqueous sodium ion systems. Therefore, the frogspawn-inspired architecture provides a new strategy to the tailored design of polyanion materials for high-power applications.Hollow micro/nano-arrays have attracted tremendous attention in the field of energy conversion and storage, but such structures usually compromise the volumetric energy density of the electrode materials. Frogspawn consists of a spawn core and a transparent jelly shell organized in

Sodium fast reactors energy conversion systems. Na-CO2 interaction. Comparison with Na-water interaction of conventional water Rankine cycle

International Nuclear Information System (INIS)

Latge, Christian; Simon, Nicole

2006-01-01

tracks for the complementary experimental study and the appraisal of the potential consequences will contribute to weighing both the advantages and drawbacks of this innovative option, in comparison to the conventional Rankine cycle. The paper has the following contents: Introduction; 1. Literature review; 2. Interaction Na-CO 2 ; 3. The Na-CO Interaction; 4. Interaction Na - Na 2 CO 3 ; 5. Carbon solubility in sodium; 6. Discussion; 7. Conclusion

Cloud-point measurement for (sulphate salts + polyethylene glycol 15000 + water) systems by the particle counting method

International Nuclear Information System (INIS)

Imani, A.; Modarress, H.; Eliassi, A.; Abdous, M.

2009-01-01

The phase separation of (water + salt + polyethylene glycol 15000) systems was studied by cloud-point measurements using the particle counting method. The effect of three kinds of sulphate salt (Na 2 SO 4 , K 2 SO 4 , (NH 4 ) 2 SO 4 ) concentration, polyethylene glycol 15000 concentration, mass ratio of polymer to salt on the cloud-point temperature of these systems have been investigated. The results obtained indicate that the cloud-point temperatures decrease linearly with increase in polyethylene glycol concentrations for different salts. Also, the cloud points decrease with an increase in mass ratio of salt to polymer.

Effects of Topical Corticosteroid and Tacrolimus on Ceramides and Irritancy to Sodium Lauryl Sulphate in Healthy Skin

DEFF Research Database (Denmark)

Jungersted, Jakob Mutanu; Høgh, Julie Kaae; Hellgren, Lars

2011-01-01

twice daily for one week with betamethasone, tacrolimus, emollient, or left untreated, respectively. After one week each area was challenged with a 24 h sodium lauryl sulphate patch test. The lipids were collected using the cyanoacrylate method and evaluated by high performance thin layer chromatography...... found between treatment regimes. Pretreatment with betamethasone (p = 0.01) or with tacrolimus (p = 0.001) causes a decreased inflammatory response to sodium lauryl sulphate compared with emollient. In conclusion, treatment with betamethasone and tacrolimus has a positive effect on the ceramide...

Proses Treatment Dengan Menggunakan NaOCl Dan H2SO4 Untuk Mempercepat Pembuatan Bioetanol Dari Limbah Rumput Laut Eucheuma Cottonii

Directory of Open Access Journals (Sweden)

I Nyoman Winjaya Putra

2012-11-01

Full Text Available The fermentation process of the waste of Eucheuma cottonii seaweed to become bioethanol can beaccelerated by providing special treatment, such as delignification process using NaOCl and immersion byusing a mixture of H2SO4 for different variations. The fermentation process is also be done by using the yeast ofSaccharomyces cerevisiae with a variety of mixtures, to determine the rate of bioethanol fermentation.In this study NaOCl has been used with variation of 0.25%, 0.50% and 0.75%. H2SO4 is used with aconcentration of 0.5% and the variations of Saccharomyces cerevisiae yeast with a ratio of 1: 0.0015; 1: 0.003;1: 0.0045; 1: 0.006 and 1: 0.0075 for every kilogram of waste Eucheuma Cottonii and yeast, and withfermentation time of 3, 6 and 9 days. As a comparison is the same treatment, but without the use of H2SO4.Based on the research, the following results obtained. The highest rate of bioethanol fermentation is4.4% per day and the highest levels of ethanol produced is 14.0%. This is achieved for where each kilogram ofwaste of Eucheuma cottonii is delignificated with a concentration of 0.5% NaOCl followed by a treatment inphysics, with the variations of yeast 1: 0.006 and with a time of fermentation for 3 days.

Overall conductivity and NCL-type relaxation behavior in nanocrystalline sodium peroxide Na{sub 2}O{sub 2}—Consequences for Na-oxygen batteries

Energy Technology Data Exchange (ETDEWEB)

Dunst, Andreas; Sternad, Michael; Wilkening, Martin, E-mail: wilkening@tugraz.at

2016-09-15

Highlights: • Na{sub 2}O{sub 2} turned out to be a poor electrical conductor. • Total conductivity of nanocrystalline Na{sub 2}O{sub 2} measured slightly above room temperature is in the order of 10{sup −15} S cm{sup −1}. • Activation energies of micro- and nanocrystalline Na{sub 2}O{sub 2} are in the order of 1 eV. • At low temperatures nearly constant loss behavior showed up pointing to locally restricted electrical relaxation processes. - Abstract: Metal air batteries are considered as promising candidates for room-temperature batteries with high-energy densities. On discharge, atmospheric oxygen is reduced at the positive electrode which, in the ideal case, forms the discharge products in a reversible cell reaction. In Na-O{sub 2} batteries upon discharge either sodium peroxide (Na{sub 2}O{sub 2}) or sodium superoxide (NaO{sub 2}) is reported to be formed. So far, the charge carrier transport remains relatively unexplored but is expected to crucially determine the efficiency of such energy storage systems. Na{sub 2}O{sub 2} is predicted to be an electrical insulator wherein the transport presumably is determined by very slow hopping processes. Understanding the basic fundamental properties of the overall charge carrier transport, including also nanostructured forms of Na{sub 2}O{sub 2}, is key to developing high-energy metal oxygen batteries. The present study answers the question how overall, i.e., total, conductivity changes when going from microcrystalline to nanocrystalline, defect-rich Na{sub 2}O{sub 2}. Nanocrystalline Na{sub 2}O{sub 2} was prepared via a top-down approach, viz by high-energy ball milling. Milling does not only shrink the average crystallite diameter but also introduces a large amount of defects which are anticipated to influence total conductivity. It turned out that even after vigorous mechanical treatment the conductivity of the sample is only increased by ca. one order of magnitude. The activation energy remains almost

Structural and impurity phase transitions of LiNaSO4:RE probed using cathodo-thermoluminescence

Science.gov (United States)

Maghrabi, M.; Finch, A. A.; Townsend, P. D.

2008-11-01

Spectrally resolved cathodo-thermoluminescence spectra of rare earth (RE) doped LiNaSO4 measured from 20 to 673 K reveal several anomalies in the RE emission lines and intensities. The low (20-300 K) temperature data show a discontinuous change in intensity at ~170 K that is either a marked intensity enhancement or a drop truncating the entire spectrum. Such an effect on the host luminescence has previously been assigned to a transition between cubic and hexagonal polymorphs of ice nanoparticle inclusions. Similar, but less profound anomalies are seen above room temperature (300-673 K) where the changes take the form of either a discontinuity in intensity at ~480 K or reduced intensity in the range 430-530 K. There are changes in the relative intensities of different emission lines of the same dopant in this temperature range. Such high temperature variations are ascribed to structural phase changes within the LiNaSO4 crystals. The behaviours may result from Li-poor surfaces or twin boundaries behaving like Na2SO4. This phase change is suggested in the open literature for LiNaSO4 but not yet fully documented, perhaps because the effects span a wide range of temperatures or due to experimental features inherent in most luminescence facilities.

Treatment for GaSb surfaces using a sulphur blended (NH4)2S/(NH4)2SO4 solution

International Nuclear Information System (INIS)

Murape, D.M.; Eassa, N.; Neethling, J.H.; Betz, R.; Coetsee, E.; Swart, H.C.; Botha, J.R.; Venter, A.

2012-01-01

A sulphur based chemical, [(NH 4 ) 2 S/(NH 4 ) 2 SO 4 ] to which S has been added, not previously reported for the treatment of (1 0 0) n-GaSb surfaces, is introduced and benchmarked against the commonly used passivants Na 2 S·9H 2 O and (NH 4 ) 2 S. The surfaces of the treated material were studied by scanning electron microscopy (SEM), Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). It has been found that the native oxides present on the GaSb surface are more effectively removed when treated with ([(NH 4 ) 2 S/(NH 4 ) 2 SO 4 ] + S) than with (NH 4 ) 2 S or Na 2 S·9H 2 O, as evidenced by the ratio of the O 506eV to Sb 457eV AES peaks. XPS results reveal that Sb 2 S 3 /Sb 2 S 5 “replaces” Sb 2 O 3 /Sb 2 O 5 , suggesting that sulphur atoms substitute oxygen atoms in Sb 2 O 3 /Sb 2 O 5 to form Sb-S. It seems sulphurization only partially removes Ga 2 O 3 . Treatment with ([(NH 4 ) 2 S/(NH 4 ) 2 SO 4 ] + S) also results in a noteworthy improvement in the current-voltage (I-V) characteristics of Au/n-GaSb Schottky contacts compared to those fabricated on as-received material.

Biomass reduction of Salvinia molesta exposed to copper sulfate pentahydrate (CuSO4.5H2O)

OpenAIRE

Barros,João Pedro Alves de Azevedo; Henares,Matheus Nicolino Peixoto

2015-01-01

Copper in the aquatic ecosystem may remain adsorbed or be incorporated into the biomass and undergo biomagnification causing unwanted effects to aquatic macrophyte communities. This study evaluated the biomass reduction of Salvinia molesta (Mitchell) exposed to copper sulphate pentahydrate (CuSO4.5H2O) under laboratory conditions. Approximately 20.5 g of fresh mass (FM) of S. molesta (0.74 g dry matter, DM) were placed in glass tanks with different concentrations (n = 3) of CuSO4.5H2O as foll...

Influence of MgSO{sub 4} doping on the properties of zinc tris–thiourea sulphate (ZTS) single crystals

Energy Technology Data Exchange (ETDEWEB)

Selvapandiyan, M., E-mail: mselvapandiyan@rediffmail.com [Department of Physics, Sri Vidya Mandir Arts and Science College, Uthangarai 635 207 (India); Arumugam, J. [Department of Physics, Sri Vidya Mandir Arts and Science College, Uthangarai 635 207 (India); Sundaramoorthi, P. [Department of Physics, Thiruvalluvar Government Arts College, Rasipuram 637 401 (India); Sudhakar, S. [CSIR–National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi 110 012 (India)

2013-12-15

Highlights: •The influence of MgSO{sub 4} doping on the properties of ZTS single crystals grown at room temperature. •Thermal stability of the crystals increased with incorporation of Mg atom. •Energy band gap was estimated from UV–vis spectra. •ZTS is a potential material for frequency conversion. •Both pure and doped ZTS crystals are belonging to category of typical insulating materials. -- Abstract: The influence of MgSO{sub 4} doping on the properties of zinc tris–thiourea sulphate single crystals grown at room temperature by slow evaporation solution growth technique was studied. Powder XRD analysis confirmed the orthorhombic crystal structure with noncentrosymmetric space group Pca2{sub 1}. The mechanical properties of the grown crystals were analysed by Vicker’s microhardness method. Functional groups present in the materials were identified by FTIR spectral analysis in the range between 4000 and 400 cm{sup −1}. The UV–Vis spectrum indicates that the UV cut-off wavelength of the crystals has less than 297 nm. The thermal stability of the grown crystals was determined with the aid of thermo-gravimetric analysis (TGA) and differential scanning calorimetry (DSC). Second order nonlinear optical behaviour of the grown crystals have been confirmed by Kurtz powder second harmonic generation (SHG) test.

Changes in 35S-sulphate uptake in different tissues in the knee and hip regions of rabbits during immobilization, remobilization and the development of osteoarthritis

International Nuclear Information System (INIS)

Videman, T.; Michelsson, J.-E.; Rauhamaeki, R.; Langenskioeld, A.

1976-01-01

In order to observe phenomena accompanying the development of osteoarthritis of the rabbit knee, consistently appearing within 4-6 weeks as a consequence of immobilization of this joint, studies on 35 S-sulphate (Na 2 - 35 SO 4 ) uptake were carried out. The investigation suggests that immobilization of the knee leads within 2-4 weeks to increased sulphate uptake in bone, cartilage and ligaments in the knee region and in the hip (not immobilized) of the same leg. The first marked changes in 35 S-sulphate uptake were found in the ligaments and the articular cartilage as early as after 4 days of immobilization. (author)

Direct extraction of a Na- beam from a sodium plasma

International Nuclear Information System (INIS)

Sasao, Namiko; Fujita, Junji; Yamaoka, Hitoshi; Wada, Motoi.

1990-07-01

Negative sodium ions (Na - ) were extracted from a small multi-cusp ion source. A steady state sodium plasma was produced by primary electrons in a sodium gas evaporating from a metal sample placed in the discharge chamber. The Na - current density of 1.5 μA/cm 2 was obtained from a single aperture of 1.5 mm diameter at relatively low discharge power of about 0.4 W and filament power of 50 W. Extraction characteristics were studied by changing the plasma electrode bias. The extracted Na - current showed dependence on the bias voltage similar to that of H - or Li - volume production. (author)

CaSO4:Dy and/or Tm: study of its properties for dosimetry application

International Nuclear Information System (INIS)

Ferreira, M.M.

1979-01-01

In order obtain in practical and cheap solid state dosimeter with high sensitivity, a technique initially developed to cold press a mixture of suitable materials in their powder form sensitive to radiation. The material initially used was natural CaF 2 (fluorite) for this salt was extensively studied in radiation dosimetry since it shows a thermoluminescent (TL) effect after radiation. However, natural calcium fluorite shows two main disadvantages: its high senstivity to room light and the impossibility to control its impurity content due to its natural origin. Calcium sulphate was thus used as a good substitute of fluorite. Rare earths doped calcium sulphate shows a high TL sensitivity and is not disturbed by light. It is also easily obtained in the laboratory under controlled conditions so to get reproducible impurity content. The best dosimeters that can be produced with rare earth doped calcium sulphate are CaSO 4 :Dy and CaSO 4 :Tm. Calcium sulphate, simultaneously doped with Tm and Dy was produced and 100% increase was obtained in the TL sensitivity when compared with the individually are earth doped calcium sulphate. (Author) [pt

Crystal structure of (Na0.70(Na0.70,Mn0.30(Fe3+,Fe2+2Fe2+(VO43, a sodium-, iron- and manganese-based vanadate with the alluaudite-type structure

Directory of Open Access Journals (Sweden)

Elhassan Benhsina

2016-02-01

Full Text Available The title compound, sodium (sodium,manganese triiron(II,III tris[vanadate(V], (Na0.70(Na0.70,Mn0.30(Fe3+,Fe2+2Fe2+(VO43, was prepared by solid-state reactions. It crystallizes in an alluaudite-like structure, characterized by a partial cationic disorder. In the structure, four of the 12 sites in the asymmetric unit are located on special positions, three on a twofold rotation axis (Wyckoff position 4e and one on an inversion centre (4b. Two sites on the twofold rotation axis are entirely filled by Fe2+ and V5+, whereas the third site has a partial occupancy of 70% by Na+. The site on the inversion centre is occupied by Na+ and Mn2+ cations in a 0.7:0.3 ratio. The remaining Fe2+ and Fe3+ atoms are statistically distributed on a general position. The three-dimensional framework of this structure is made up of kinked chains of edge-sharing [FeO6] octahedra stacked parallel to [10-1]. These chains are held together by VO4 tetrahedral groups, forming polyhedral sheets perpendicular to [010]. Within this framework, two types of channels extending along [001] are present. One is occupied by (Na+/Mn2+ while the second is partially occupied by Na+. The mixed site containing (Na+/Mn2+ has an octahedral coordination sphere, while the Na+ cations in the second channel are coordinated by eight O atoms.

Combined CO/CH4 oxidation tests over Pd/Co3O4 monolithic catalyst. Effects of high reaction temperature and SO2 exposure on the deactivation process

International Nuclear Information System (INIS)

Liotta, L.F.; Venezia, A.M.; Di Carlo, G.; Pantaleo, G.; Deganello, G.; Merlone Borla, E.; Pidria, M.

2007-01-01

CO and CH 4 combined oxidation tests were performed over a Pd (70 g/ft 3 )/Co 3 O 4 monolithic catalyst in conditions of GHSV = 100,000 h -1 and feed composition close to that of emission from bi-fuel vehicles. The effect of SO 2 (5 ppm) on CO and CH 4 oxidation activity under lean condition (λ 2) was investigated. The presence of sulphur strongly deactivated the catalyst towards methane oxidation, while the poisoning effect was less drastic in the oxidation of CO. Saturation of the Pd/Co 3 O 4 catalytic sites via chemisorbed SO 3 and/or sulphates occurred upon exposure to SO 2 . A treatment of regeneration to remove sulphate species was attempted by performing a heating/cooling cycle up to 900 C in oxidizing atmosphere. Decomposition of PdO and Co 3 O 4 phases at high temperature, above 750 C, was observed. Moreover, sintering of Pd 0 and PdO particles along with of CoO crystallites takes place. (author)

Systems Li2B4O7 (Na2B4O7, K2B4O7)-N2H3H4OH-H2O at 25 deg C

International Nuclear Information System (INIS)

Skvortsov, V.G.; Sadetdinov, Sh.V.; Akimov, V.M.; Mitrasov, Yu.N.; Petrova, O.V.; Klopov, Yu.N.

1994-01-01

Phase equilibriums in the Li 2 B 4 O 7 (Na 2 B 4 O 7 , K 2 B 4 O 7 )-N 2 H 3 H 4 OH-H 2 O systems were investigated by methods of isothermal solubility, refractometry and PH-metry at 25 deg C for the first time. Lithium and sodium tetraborates was established to form phases of changed composition mM 2 B 4 O 7 ·nN 2 H 3 C 2 H 4 OH·XH 2 O, where M=Li, Na with hydrazine ethanol. K 2 B 4 O 7 ·4H 2 O precipitates in solid phase in the case of potassium salt. Formation of isomorphous mixtures was supported by X-ray diffraction and IR spectroscopy methods

Determination of deuterium in water by a thermometric method

International Nuclear Information System (INIS)

Gabicar, J.

1976-01-01

A simple and rapid method for the determination of deuterium in water has been developed. The method is based on the change of the thermal effect of the solubility of sodium sulphate in the presence of D 2 O. The procedure is based on the measurement of the temperature of phase transition Na 2 SO 4 . 10 H 2 O reversible Na 2 SO 4 + 10 H 2 O. The sensitivity of the method proposed is comparable with mass spectrometry. (author)

Microstructural characterization and electrochemical corrosion behavior of Incoloy 800 in sulphate and chloride solutions

International Nuclear Information System (INIS)

Mansur, Fabio Abud; Schvartzman, Monica Maria de Abreu Mendonca; Campos, Wagner Reis da Costa; Aguiar, Antonio Eugenio de; Chaim, Marcos Souza

2011-01-01

Corrosion has been the major cause of tube failures in steam generators (SG) tubes in nuclear power plants. Problems have resulted from impurities in the secondary water systems which are originated from leaks of cooling water. It is important to understand the compatibility of steam generator tube materials with the environment. This study presents the microstructural characterization and electrochemical behavior of the Incoloy 800 in sodium chloride and sodium sulphate aqueous solutions at 80 degree C. Potentiodynamic anodic polarization, cyclic polarization and open circuit potential (OCP) measurements were the electrochemical techniques applied in this work. The pitting resistance of Incoloy 800 in chloride plus sulphate mixtures were also examined. Experiments performed in solutions with different concentrations of Cl- and SO 4 2- ions in solution (200 ppb, 500 ppb, 1ppm, 5 ppm, 50 ppm and 100 ppm) showed that this concentrations range had no substantial effect on the anodic behavior of the alloy. After polarization no localized corrosion was found on the samples. (author)

Obtention of agricultural gypsum traced on 34 S (Ca34 SO4.2H2O), by chemical reaction between H234 SO4 and Ca(OH)2

International Nuclear Information System (INIS)

Rossete, Alessandra L.R.M.; Bendassolli, Jose A.; Ignoto, Raquel de Fatima; Batagello, Hugo Henrique

2002-01-01

The gypsum (CaSO 4 .2H 2 O) has double function in the soil: as source of calcium and sulfur and reducing agent of aluminum saturation. The sulfur for the plants has acting in the vital functions and it is proven fact increase of the S deficiency in Brazilian soils. The isotope tracer 34 S can elucidate important aspects in the sulfur cycle. The Ca 34 SO 4 .2H 2 O was obtained by chemical reaction between Ca(OH) 2 and H 2 34 SO 4 solution. The acid was obtained by chromatography ionic change, using cationic resin Dowex 50WX8 and Na 2 34 SO 4 solution. The reaction was realized under slow agitation. After the reaction, the precipitate was separated and dried in ventilated stove at 60 deg C temperature. The Mass of the Ca 34 SO 4 .2H 2 O produced was determined by method gravimetric. This way, a system contends resin 426 cm 3 , considering volume of 2.2 liters can be obtained a solution contends 44.2 g of H 2 34 SO 4 , theoretically could be produced 78.0 g of Ca 34 SO 4 .2H 2 O approximately. With results of the tests were verified that there was not total precipitation of the Ca 34 SO 4 .2H 2 O. Were produced 73.7± 0.6 g of Ca 34 SO 4 .2H 2 O representing average income 94.6±0.8 %. The purity of the produced CaSO 4 .2H 2 O was 98%. (author)

Small angle neutron scattering studies of mixed micelles of sodium

Indian Academy of Sciences (India)

The aqueous solutions of sodium cumene sulphonate (NaCS) and its mixtures with each of cetyl trimethylammonium bromide (CTAB) and sodium dodecyl sulphate (SDS) are characterized by small angle neutron scattering (SANS). NaCS when added to CTAB solution leads to the formation of long rod-shaped micelles with ...

Acute Toxicity and the Effects of Copper Sulphate (CuSO4.5H2O on the Behavior of the Black Fish (Capoeta Fusca

Directory of Open Access Journals (Sweden)

Iman Zarei

2013-02-01

Full Text Available Background: The development of toxicity tests regarding toxic responses of different fish species could be more effectively used in predictive toxicology and risk assessment. In this study lethal concentrations (LC50-96 h values of copper sulphate; an important toxic industrial pollutant, on Capoeta fusca were determined. Behavioral changes at different concentrations of CuSO4 were determined for the C.fusca. Methods: The sample fishes were collected from Qanat in Birjand and were transported to the laboratory in polythene bags. The exposure time of fish to CuSO4 was 96 hours. Mortalities were recorded at 24, 48, 72, and 96 hours of exposure, and the dead fish were removed regularly from the test aquariums. Physicochemical parameters, such as dissolved oxygen, pH and Total hardness of aquaria were monitored daily. Results: The LC50 values for CuSO4 at 24, 48, 72, and 96 h of exposure, were 43.62, 12.6, 7.66, and 6.85 mg/L, respectively. The median LC50 value of CuSO4 for C.fusca was found to be 6.928 mg/L by EPA method and estimated to be 6.787 mg/L with SPSS statistical software. Conclusion: The mortality decreased with time, and most of the deaths occurred during the first 24 h. In addition, behavioural changes increased with increased concentration. This metal is an important constituent in industrial effluents discharged into freshwaters. The results obtained in this study clearly revealed the fact that it is necessary to control the use of a heavy metal such as copper.

Sodium diethyldithiocarbamate as accelerator of the rate of copper cementation

Directory of Open Access Journals (Sweden)

Abeer A. El-Saharty

2015-12-01

Full Text Available The effects of Cu2+ ion concentration and temperature on the cementation rate of copper from copper sulphate on zinc and the effect of additives of the organic compound “sodium diethyldithiocarbamate” (NaDDC were studied. It was noticed that the cementation increases significantly by increasing the concentrations of NaDDC. The rate of cementation increased by 58.58−100.31%. Our data showed that sodium diethyldithiocarbamate reacts with the Cu2+ solution giving a complex of copper diethyldithiocarbamate, which enhances the rate of cementation.

Enhanced electrochemical performance of Ti substituted P2-Na2/3Ni1/4Mn3/4O2 cathode material for sodium ion batteries

International Nuclear Information System (INIS)

Zhao, Wenwen; Tanaka, Akinobu; Momosaki, Kyoko; Yamamoto, Shinji; Zhang, Fabi; Guo, Qixin; Noguchi, Hideyuki

2015-01-01

Highlights: • Ti substituted P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode was synthesized. • Structural and electrochemical properties of Na 2/3 Ni 1/4 Ti x Mn 3/4-x O 2 were studied. • Ti substituted cathodes exhibit enhanced cycleability and rate performance. • Ti substitution has impact on stabilizing the P2 structure during cycling. -- Abstract: Ti substituted P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode material with the composition of Na 2/3 Ni 1/4 Ti x Mn 3/4-x O 2 has been synthesized by solid state method. The influence of Ti substitution for Mn on the structure, morphology and electrochemical performances of P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 has been investigated. X-ray diffraction (XRD) results of Ti substituted sample show that they exhibit same diffraction patterns as those of pristine P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 . Progressive change in the lattice parameters of Ti substituted samples suggests that Mn was successfully substituted by Ti. In contrast to P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 which shows step-type voltage profiles, Ti substituted samples show sloping voltage profiles. Drastic capacity fade occurred for P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode, while Ti substituted cathodes still show high capacity retention over 92% after 25 cycles at the voltage range of 2.0-4.3 V. Even cycled at high upper cut-off voltage of 4.5 V, Ti=0.20 sample can deliver a reversible capacity of 140 mAhg −1 with the capacity retention over 92% after 25 cycles. Furthermore, Ti substituted cathodes exhibit enhanced rate capability over pristine P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 cathode. Comparison of the Ex-situ XRD results of the cycled P2-Na 2/3 Ni 1/4 Mn 3/4 O 2 and its substituted samples provides evidence that the improved electrochemical performance of Ti substituted cathodes would be attributed to the stabilization of the structure with Ti substitution

Mechanochemical transformations in Li(Na)AlH{sub 4}-Li(Na)NH{sub 2} systems

Energy Technology Data Exchange (ETDEWEB)

Dolotko, Oleksandr [Ames Laboratory of the U.S. DOE, Iowa State University, Ames, IA 50011-3020 (United States); Zhang Haiqiao [Ames Laboratory of the U.S. DOE, Iowa State University, Ames, IA 50011-3020 (United States); Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011-2300 (United States); Ugurlu, Ozan [Ames Laboratory of the U.S. DOE, Iowa State University, Ames, IA 50011-3020 (United States); Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011-2300 (United States); Wiench, Jerzy W. [Ames Laboratory of the U.S. DOE, Iowa State University, Ames, IA 50011-3020 (United States); Pruski, Marek [Ames Laboratory of the U.S. DOE, Iowa State University, Ames, IA 50011-3020 (United States); Scott Chumbley, L. [Ames Laboratory of the U.S. DOE, Iowa State University, Ames, IA 50011-3020 (United States); Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011-2300 (United States); Pecharsky, Vitalij [Ames Laboratory of the U.S. DOE, Iowa State University, Ames, IA 50011-3020 (United States) and Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011-2300 (United States)]. E-mail: vitkp@ameslab.gov

2007-05-15

Mechanochemical transformations of tetrahydroaluminates and amides of lithium and sodium have been investigated using gas volumetric analysis, X-ray powder diffraction, solid-state nuclear magnetic resonance (NMR) and transmission electron microscopy. In a transformation of LiAlH{sub 4} and LiNH{sub 2} taken in an 1:1 molar ratio, the amount of released hydrogen (6.6 wt.% after 30 min ball milling) was higher than in any known one pot mechanochemical process involving a hydrogen-containing solid. A total of 4.3 wt.% of hydrogen is released by the NaAlH{sub 4}-NaNH{sub 2} system after 60 min ball milling; and 5.2 wt.% H{sub 2} is released when LiAlH{sub 4} and NaNH{sub 2} or NaAlH{sub 4} and LiNH{sub 2} are ball milled for 90 min and 120 min, respectively. All transformations proceed at room temperature. The mechanism of the overall transformation MAlH{sub 4}(s) + MNH{sub 2}(s) {sup {yields}} 2MH(s) + AlN(s) + 2H{sub 2}(g) was identified based on detailed spectroscopic analysis of the intermediate (M{sub 3}AlH{sub 6}) and final products of the ball milling process.

Sulphate deposition by precipitation into Lake Ontario

Energy Technology Data Exchange (ETDEWEB)

Shaw, R W; Whelpdale, D M

1973-01-01

Measurements of sulphate concentration in precipitation from individual snow storms of several hours duration in the western Lake Ontario region indicate that approximately 9-66 mg/M/sub 2/ of SO/sub 4//sup 2 -/ is being deposited into the lake per storm. This amount is up to several times more than daily average values over long periods found by other workers. Using a mean sulphate concentration of 4 mg/l and an annual accumulation of precipitation of 760 mm, the yearly sulphate deposition by precipitation is about 0.1% of the total mass of sulphate in the lake; however, more significantly, it is of the same order of magnitude as that discharged directly into the lake by industry.

Removal of sodium lauryl sulphate by coagulation/flocculation with Moringa oleifera seed extract.

Science.gov (United States)

Beltrán-Heredia, J; Sánchez-Martín, J

2009-05-30

Among other natural flocculant/coagulant agents, Moringa oleifera seed extract ability to remove an anionic surfactant has been evaluated and it has been found to be very interesting. Sodium lauryl sulphate was removed from aqueous solutions up to 80% through coagulation/flocculation process. pH and temperature were found to be not very important factors in removal efficiency. Freundlich (F), Frumkin-Fowler-Guggenheim (FFG) and Gu-Zhu (GZ) models were used to adjust experimental data in a solid-liquid adsorption hypothesis. Last one resulted to be the most accurate one. Several data fit parameters were determined, as Freundlich order, which was found to be 1.66, Flory-Huggins interaction parameter from FFG model, which was found to be 4.87; and limiting Moringa surfactant adsorption capacity from GZ model, which was found to be 2.13 x 10(-3)mol/g.

Synthesis and fluorescence study of sodium-2-(4'-dimethyl-aminocinnamicacyl)-3,3-(1',3'-alkylenedithio) acrylate

International Nuclear Information System (INIS)

Si Zhenjun; Shao Yun; Li Chunxia; Liu Qun

2007-01-01

We synthesized two new compounds: Sodium 2-(4'-dimethyl-aminocinnamicacyl)-3,3-(1',3'- ethyl- enedithio) acrylate (STAA-1) and Sodium 2-(4'-dimethyl-aminocinnamicacyl)-3, 3-(1',3'-propylenedithio) acrylate (STAA-2). The maximum absorption of these compounds ranges from 460 to 520 nm with different molecular structures in different solvents. Meanwhile, the emission peak of these compounds arranges from yellow (510 nm) to red (605 nm). The emission spectra show red shift according to the strength of the hydrogen bonding property of the solvent. But the absorption spectra do not show clearly relationship with the strength of the hydrogen bonding property of the solvent. The Stoke shift of the compounds ranges from 42 to 102 nm. It changes in the following order, EtOH>H 2 O>DMF, and STAA-1>STAA-2 in the same solvent. The fluorescent quantum yield of STAA-1 was measured to be 7.12% with quinine sulphate as the standard compound in ethanol. Furthermore, the relationship of the fluorescence of STAA-1 with pH (ranges form 4 to 14) in water (c=∼10 -4 ) was studied to make sure that these compounds could be used as proton sensors

Synthesis, crystal structure and spectroscopy properties of Na 3AZr(PO 4) 3 ( A=Mg, Ni) and Li 2.6Na 0.4NiZr(PO 4) 3 phosphates

Science.gov (United States)

Chakir, M.; El Jazouli, A.; de Waal, D.

2006-06-01

Na 3AZr(PO 4) 3 ( A=Mg, Ni) phosphates were prepared at 750 °C by coprecipitation route. Their crystal structures have been refined at room temperature from X-ray powder diffraction data using Rietveld method. Li 2.6Na 0.4NiZr(PO 4) 3 was synthesized through ion exchange from the sodium analog. These materials belong to the Nasicon-type structure. Raman spectra of Na 3AZr(PO 4) 3 ( A=Mg, Ni) phosphates present broad peaks in favor of the statistical distribution in the sites around PO 4 tetrahedra. Diffuse reflectance spectra indicate the presence of octahedrally coordinated Ni 2+ ions.

Polymerization of Methyl Methacrylate Initiated by PADC-Cu(Ⅱ)/ Na2 SO3/H2O System%PADC-Cu(Ⅱ)/Na2SO3/H2O体系引发MMA聚合

Institute of Scientific and Technical Information of China (English)

崔元臣; 刘新明; 赵晓伟; 张磊

2006-01-01

由含N,O,S多官能团的螯合树脂PADC和Cu2+作用制得一种新型的高分子金属配合物,用IR、XPS、AAS、TG/DTA对其结构进行了表征.以该配合物和Na2SO3水溶液组成的体系应用于引发MMA聚合,结果表明:PADC-Cu(Ⅱ)/Na2SO3体系可以有效地引发MMA聚合,反应表观活化能Ea=57.4 kJmol-1,并详细研究了影响产率和分子量的各因素,由该体系引发MMA聚合的分子量可达213万,在6h内产率就达58.6%.初步讨论了该聚合过程是一种自由基聚合过程,初始自由基由PADC-Cu2+/Na2SO3/MMA体系"配位氢转移"产生.

Robust high pressure stability and negative thermal expansion in sodium-rich antiperovskites Na3OBr and Na4OI2

International Nuclear Information System (INIS)

Wang, Yonggang; Wen, Ting; Park, Changyong; Kenney-Benson, Curtis; Pravica, Michael; Zhao, Yusheng; Yang, Wenge

2016-01-01

The structure stability under high pressure and thermal expansion behavior of Na 3 OBr and Na 4 OI 2 , two prototypes of alkali-metal-rich antiperovskites, were investigated by in situ synchrotron X-ray diffraction techniques under high pressure and low temperature. Both are soft materials with bulk modulus of 58.6 GPa and 52.0 GPa for Na 3 OBr and Na 4 OI 2 , respectively. The cubic Na 3 OBr structure and tetragonal Na 4 OI 2 with intergrowth K 2 NiF 4 structure are stable under high pressure up to 23 GPa. Although being a characteristic layered structure, Na 4 OI 2 exhibits nearly isotropic compressibility. Negative thermal expansion was observed at low temperature range (20–80 K) in both transition-metal-free antiperovskites for the first time. The robust high pressure structure stability was examined and confirmed by first-principles calculations among various possible polymorphisms qualitatively. The results provide in-depth understanding of the negative thermal expansion and robust crystal structure stability of these antiperovskite systems and their potential applications

Synthesis and thermoluminescence characterization of Na6Mg(SO4)4:RE (RE = Ce, Tb) phosphors

International Nuclear Information System (INIS)

Kore, Bhushan P.; Dhoble, N.S.; Dhoble, S.J.

2014-01-01

Thermoluminescence (TL) properties of sulfate-based phosphors activated by different rare earths have received tremendous attention to the field of radiation dosimetry. Those TL materials based on CaSO 4 have been widely applied for medical and environmental dosimetry. Taking this fact into account we have synthesized Na 6 Mg(SO 4 ) 4 doped with Ce and Tb by wet chemical method. The prepared phosphor was characterized by XRD, FTIR, photoluminescence (PL) and thermoluminescence. For TL study, the phosphor is irradiated with γ-rays from 60 Co source. For studying luminescence properties, the prepared phosphor was annealed at different temperatures and effects of these annealing temperatures on Na 6 Mg(SO 4 ) 4 samples are investigated and quantified. The changes in the glow curve and PL emission spectrum are also investigated as a function of annealing temperature and the annealing temperature was optimized. For calculation of trapping parameters various methods such as peak shape (PS) method, initial rise (IR) method, various heating rate (VHR) method, and computerized glow curve deconvolution (CGCD) are employed. - Highlights: • Na 6 Mg(SO 4 ) 4 phosphor was successfully prepared by wet chemical method. • Effect of annealing temperatures on PL and TL properties has been studied. • Different trap analysis methods were used for calculating the trapping parameters. • Effect of these methods on activation energies were investigated in detail

Integrated dry NO{sub x}/SO{sub 2} emissions control system sodium-based dry sorbent injection test report. Test period: August 4, 1993--July 29, 1995

Energy Technology Data Exchange (ETDEWEB)

Smith, R.A.; Shimoto, G.H.; Muzio, L.J. [Fossil Energy Research Corp., Laguna Hills, CA (United States); Hunt, T. [Public Service Co. of Colorado, Denver, CO (United States)

1997-04-01

The project goal is to demonstrate up to 70% reductions in NOx and SO{sub 2} emissions through the integration of: (1) down-fired low-NOx burners with overfire air; (2) Selective Non-Catalytic Reduction (SNCR) for additional NOx removal; and (3) dry sorbent injection and duct humidification for SO{sub 2} removal. This report documents the sixth phase of the test program, where the performance of dry sorbent injection with sodium compounds was evaluated as a SO{sub 2} removal technique. Dry sorbent injection was performed in-duct downstream of the air heater (ahead of the fabric filter), as well as at a higher temperature location between the economizer and air heater. Two sodium compounds were evaluated during this phase of testing: sodium sesquicarbonate and sodium bicarbonate. In-duct sodium injection with low levels of humidification was also investigated. This sixth test phase was primarily focused on a parametric investigation of sorbent type and feed rate, although boiler load and sorbent preparation parameters were also varied.

A 125Te and 23Na NMR investigation of the structure and crystallisation of sodium tellurite glasses.

Science.gov (United States)

Holland, D; Bailey, J; Ward, G; Turner, B; Tierney, P; Dupree, R

2005-01-01

125Te static nuclear magnetic resonance (NMR) and 23Na and 125Te magic angle spinning (MAS) NMR have been used, in conjunction with X-ray diffraction, to examine the structure and crystallisation behaviour of glasses of composition xNa2O.(1-x)TeO2 (0.075 x 0.4). The MAS NMR 23Na spectra from the glasses are broad and featureless but shift by approximately +5 ppm with increased x, i.e. as the system becomes more ionic. The static 125Te NMR spectra show an increase in axial symmetry with increasing x, indicating a shift from predominantly [TeO4] to [TeO3] structural units. The 23Na and 125Te spectra from the crystallised samples have been fitted to obtain information on the sites in the metastable crystal phases, which are the first to form on heating and which are therefore more closely related to the glass structure than thermodynamically stable crystal phases. New sodium tellurite phases are reported, including a sodium stabilised, face centred cubic phase related to delta-TeO2; a metastable form of Na2Te4O9 containing 3 sodium and 4 tellurium sites; and a metastable form of Na2Te2O5 containing 2 sodium sites. There is evidence of oxidation of TeIV to TeVI occurring in glasses with high values of x and, at x=0.40 and 0.50 (outside the glass forming range), some sodium metatellurate (Na2TeO4) is formed at the same time as sodium metatellurite (Na2TeO3). The 125Te shift is very sensitive to environment within the sodium tellurite system, covering more than 320 ppm, with anisotropies varying from 640 to 1540 ppm. The lack of features in the 125Te spectra of the glass phases, combined with the large shift range and high but variable anisotropy, means than it is not possible to obtain a unique fit to any presumed species present. Furthermore, the chemical shift anisotropy parameters for three of the four Te sites in the Na2Te4O9 phase are found to lie outside the range used for previous simulations of glass spectra.

An ultrathin polymer coating of carboxylate self-assembled monolayer adsorbed on passivated iron to prevent iron corrosion in 0.1 M Na2SO4

International Nuclear Information System (INIS)

Aramaki, Kunitsugu; Shimura, Tadashi

2010-01-01

For preparing an ultrathin two-dimensional polymer coating adsorbed on passivated iron, a 16-hydroxyhexadecanoate ion HO(CH 2 ) 15 CO 2 - self-assembled monolayer (SAM) was modified with 1,2-bis(triethoxysilyl)ethane (C 2 H 5 O) 3 Si(CH 2 ) 2 Si(OC 2 H 5 ) 3 and octadecyltriethoxysilane C 18 H 37 Si(OC 2 H 5 ) 3 . Protection of passivated iron against passive film breakdown and corrosion of iron was investigated by monitoring of the open-circuit potential and repeated polarization measurements in an aerated 0.1 M Na 2 SO 4 solution during immersion for many hours. The time required for passive film breakdown of the polymer-coated electrode was markedly higher in this solution than that of the passivated one, indicating protection of the passive film from breakdown by coverage with the polymer coating. The protective efficiencies of the passive film covered with the coating were extremely high, more than 99.9% in 0.1 M Na 2 SO 4 before the passive film was broken down, showing prominent cooperative suppression of iron corrosion in the solution by coverage with the passive film and polymer coating. The polymer-coated surface was characterized by contact angle measurement and electron-probe microanalysis (EPMA). Prevention of passive film breakdown and iron corrosion for the polymer-coated electrode healed in 0.1 M NaNO 3 was also examined in 0.1 M Na 2 SO 4 .

Eldfellite, NaFe(SO₄)₂, a new fumarolic mineral from Eldfell volcano, Iceland

DEFF Research Database (Denmark)

Balic Zunic, Tonci; Garavelli, A.; Acquafredda, P.

2009-01-01

A new mineral, eldfellite, was found among fumarolic encrustations collected in 1990 on the Eldfell volcano, Heimaey Island, Iceland. Associated minerals are ralstonite, anhydrite, gypsum, bassanite, hematite, opal and tamarugite, as well as a presumably new mineral with the composition Na3Fe(SO4......)3. Along with opal and tamarugite, eldfellite forms soft and fragile aggregates built of thin, platy crystals of micrometre size. The mineral is yellowish-green to greenish-white, with a white streak. The calculated density is 3.062 g/cm3. Eldfellite is monoclinic, C2/m, a 8.043(4) Å, b 5.139(2) Å, c 7...

Inactivation of heat adapted and chlorine adapted Listeria monocytogenes ATCC 7644 on tomatoes using sodium dodecyl sulphate, levulinic acid and sodium hypochlorite solution

Directory of Open Access Journals (Sweden)

Oluwatosin Ademola Ijabadeniyi

2017-04-01

Full Text Available The effectiveness of sodium dodecyl sulphate (SDS, sodium hypochlorite solution and levulinic acid in reducing the survival of heat adapted and chlorine adapted Listeria monocytogenes ATCC 7644 was evaluated. The results against heat adapted L. monocytognes revealed that sodium hypochlorite solution was the least effective, achieving log reduction of 2.75, 2.94 and 3.97 log colony forming unit (CFU/mL for 1, 3 and 5 minutes, respectively. SDS was able to achieve 8 log reduction for both heat adapted and chlorine adapted bacteria. When used against chlorine adapted L. monocytogenes sodium hypochlorite solution achieved log reduction of 2.76, 2.93 and 3.65 log CFU/mL for 1, 3 and 5 minutes, respectively. Using levulinic acid on heat adapted bacteria achieved log reduction of 3.07, 2.78 and 4.97 log CFU/mL for 1, 3, 5 minutes, respectively. On chlorine adapted bacteria levulinic acid achieved log reduction of 2.77, 3.07 and 5.21 log CFU/mL for 1, 3 and 5 minutes, respectively. Using a mixture of 0.05% SDS and 0.5% levulinic acid on heat adapted bacteria achieved log reduction of 3.13, 3.32 and 4.79 log CFU/mL for 1, 3 and 5 minutes while on chlorine adapted bacteria it achieved 3.20, 3.33 and 5.66 log CFU/mL, respectively. Increasing contact time also increased log reduction for both test pathogens. A storage period of up to 72 hours resulted in progressive log reduction for both test pathogens. Results also revealed that there was a significant difference (P≤0.05 among contact times, storage times and sanitizers. Findings from this study can be used to select suitable sanitizers and contact times for heat and chlorine adapted L. monocytogenes in the fresh produce industry.

Time-temperature influence on the corrosion resistance of Ni-Cr-Nb superalloys in contact with Na2SO4-V2O5 molten mixtures

International Nuclear Information System (INIS)

Otero, E.; Pardo, A.; Hernaez, J.; Hierro, P.

1990-01-01

Corrosion rate data obtained by the polarization resistance method in nickel-base superalloys in contact with Na 2 SO 4 -V 2 O 5 molten mixtures are presented. The instrumental technique is also described. Time-temperature influence on the corrosion kinetics in the described conditions is discussed (Author)

Thermoluminescence mechanisms in CaSO4:Dy single crystals

International Nuclear Information System (INIS)

Morgan, M.D.; Stoebe, T.G.

1986-01-01

ESR studies of gamma-irradiated CaSO 4 :Dy have shown, in addition to the usual intrinsic defects, four new paramagnetic centres. An analysis of the g values and the g tensors in conjunction with the anhydrite crystal structure indicate that these centres are related to sulphate ions. Two of these centres (denoted 1a and 3a) are proposed as holes trapped and shared between two adjacent sulphate ions, this structure being stabilised by a neighbouring Ca vacancy. Centre 3b is suggested as a hole associated with one sulphate ion, again stabilised by an adjacent Ca vacancy. Because of the two distinct crystallographic directions in the anhydrite structure, centre 3b was found to consist of two distinguishable defects with slightly differing decay temperatures. The fourth centre appears to be an electron trapping site with structure similar to centre 3b. Decay temperatures of these ESR defects are correlated with the observance of TL peaks in CaSO 4 :Dy. Thermoluminescence studies as a function of impurity content confirmed the presence of calcium vacancies, which are formed during crystal growth, and that they play an important role in the TL process. TL models are proposed to account for the observed properties of CaSO 4 :Dy. (author)

Thermodynamic study of sodium-iron oxides. Part 2. Ternary phase diagram of the Na-Fe-O system

International Nuclear Information System (INIS)

Huang, Jintao; Furukawa, Tomohiro; Aoto, Kazumi

2003-01-01

Studies on ternary phase diagrams of the Na-Fe-O system have been carried out from the thermodynamic point of view. Thermodynamic data of main ternary Na-Fe oxides Na 4 FeO 3 (s), Na 3 FeO 3 (s), Na 5 FeO 4 (s) and Na 8 Fe 2 O 7 (s) have been assessed. A user database has been created by reviewing literature data together with recent DSC and vapor pressure measurements by the present authors. New ternary phase diagrams of the Na-Fe-O system have been constructed from room temperature to 1000K. Stable conditions of the ternary oxides at 800K were presented in predominance diagram as functions of oxygen pressure and sodium pressure

The U phase formation in cement-based systems containing high amounts of Na2SO4

International Nuclear Information System (INIS)

Li, G.; Moranville, M.; Le Bescop, P.

1996-01-01

Simulated cemented low level wastes containing high amounts of Na 2 SO 4 (10--15%) were examined with respect to the mineralogy of the solid phases, chemical composition of the interstitial aqueous phase and immersion behavior in water. All results reveal the formation of a mineral called U phase, first observed by Dosch and zur Strassen in 1967, and its deleterious effects on the samples immersed in water. It appears that this phase can form only at very high alkaline concentration, not compatible with traditional cement paste. Two possible degradation mechanisms associated with the U phase are proposed which are to be elucidated in further works

Electrochemical noise measurements of steel corrosion in the molten NaCl-K2SO4 system

DEFF Research Database (Denmark)

Cappeln, Frederik Vilhelm; Bjerrum, Niels; Petrushina, Irina

2005-01-01

-called active corrosion (i.e., the corrosion proceeds with no passivation due to the influence of chlorine), characterized by the formation of volatile metal chlorides as a primary corrosion product. It was found possible to obtain an empirical separation of general and intergranular corrosion using kurtosis (a......Electrochemical noise measurements have been carried out on AISI347, 10CrMo910, 15Mo3, and X20CrMoV121 steels in molten NaCl-K2SO4 at 630 degrees C. Different types of current noise have been identified for pitting, intergranular and peeling corrosion. The corrosion mechanism was the so...... statistical parameter calculated from the electrochemical noise data). It was found that average kurtosis values above 6 indicated intergranular corrosion and average values below 6 indicated general corrosion. The response time for localized corrosion detection in in-plant monitoring was approximately 90 min...

Thermodynamics of {l_brace}zNaCl+(1-z)Na{sub 2}SO{sub 4}{r_brace}(aq) from T=278.15 K to T=318.15 K, and representation with an extended ion-interaction (Pitzer) model

Energy Technology Data Exchange (ETDEWEB)

Rard, Joseph A. E-mail: rard1@llnl.gov; Clegg, Simon L.; Platford, Robert

2003-06-01

In 1968, R.F. Platford reported the results from extensive isopiestic vapor-pressure measurements for the {l_brace}zNaCl+(1-z)Na{sub 2}SO{sub 4}{r_brace}(aq) system at T=298.15 K, using NaCl(aq) as the isopiestic reference standard [R.F. Platford, J. Chem. Eng. Data 13 (1968) 46-48]. However, only derived quantities were reported, and the experimental isopiestic equilibrium molalities were not given. The complete set of original isopiestic molalities from that study is tabulated in the present report. In addition, published thermodynamic information for this system is reviewed and the isopiestic equilibrium molalities, electromotive force measurements for five different types of electrochemical cells, and enthalpies of mixing from these other studies are critically assessed and recalculated consistently. These combined results are used to evaluate at T=298.15 K the two mixing parameters of Pitzer's ion-interaction model, {sup S}{theta}(Cl,SO{sub 4})=(1.236{+-}0.032{sub 5}){center_dot}10{sup -2} kg{center_dot}mol{sup -1} and {psi}(Na,Cl,SO{sub 4})=(1.808{+-}0.086){center_dot}10{sup -3} kg{sup 2}{center_dot}mol{sup -2}, and their temperature derivatives {l_brace}{partial_derivative}{sup S}{theta}(Cl,SO{sub 4})/{partial_derivative}T{r_brace}{sub p}=(2.474{+-}0.460){center_dot}10{sup -5} kg{center_dot}mol{sup -1}{center_dot}K{sup -1} and {l_brace}{partial_derivative}{psi}(Na,Cl,SO{sub 4})/{partial_derivative}T{r_brace}{sub p}=-(6.228{+-}0.186){center_dot}10{sup -5} kg{sup 2}{center_dot}mol{sup -2}{center_dot}K{sup -1}. Also reported are parameters for an extended ion-interaction model for Na{sub 2}SO{sub 4}(aq), valid from T=(273.15 to 323.15) K, that were required for this mixed electrolyte solution analysis.

In situ observation of initial rust formation process on carbon steel under Na2SO4 and NaCl solution films with wet/dry cycles using synchrotron radiation X-rays

International Nuclear Information System (INIS)

Yamashita, M.; Konishi, H.; Kozakura, T.; Mizuki, J.; Uchida, H.

2005-01-01

Atmospheric corrosion of steel proceeds under thin electrolyte film formed by rain and dew condensation followed by wet and dry cycles. It is said that rust layer formed on steel as a result of atmospheric corrosion strongly affects the corrosion behavior of steel. The effect of environmental corrosiveness on the formation process and structure of the rust layer is, however, not clear to date. In this study, in situ observation of the rusting process of a carbon steel covered with a thin film of Na 2 SO 4 or NaCl solution was performed under a wet/dry repeating condition by X-ray diffraction spectroscopy with white X-rays obtained from synchrotron radiation. The present in situ experiments successfully detected initial process of the rust formation. In the early cycles, the rust constituents were not well crystallized yet, but the presence of Fe(OH) 2 and Fe(OH) 3 was confirmed. In the subsequent cycles, two different solutions resulted in difference in preferential phase of the rust constituents. α-FeOOH was preferentially formed in the case of the Na 2 SO 4 solution film, whereas β-FeOOH appeared only under the NaCl solution film

The effect of magnesium on partial sulphate removal from mine water as gypsum.

Science.gov (United States)

Tolonen, Emma-Tuulia; Rämö, Jaakko; Lassi, Ulla

2015-08-15

The aim of this research was to investigate the effect of magnesium on the removal efficiency of sulphate as gypsum from mine water. The precipitation conditions were simulated with MINEQL + software and the simulation results were compared with the results from laboratory jar test experiments. Both the simulation and the laboratory results showed that magnesium in the mine water was maintaining sulphate in a soluble form as magnesium sulphate (MgSO4) at pH 9.6. Thus magnesium was preventing the removal of sulphate as gypsum (CaSO4·2H2O). However, change in the lime precipitation pH from 9.6 to 12.5 resulted in magnesium hydroxide (Mg(OH)2) precipitation and improved sulphate removal. Additionally, magnesium hydroxide could act as seed crystals for gypsum precipitation or co-precipitate sulphate further enhancing the removal of sulphate from mine water. Copyright © 2015 Elsevier Ltd. All rights reserved.

Crystalline maricite NaFePO4 as a positive electrode material for sodium secondary batteries operating at intermediate temperature

Science.gov (United States)

Hwang, Jinkwang; Matsumoto, Kazuhiko; Orikasa, Yuki; Katayama, Misaki; Inada, Yasuhiro; Nohira, Toshiyuki; Hagiwara, Rika

2018-02-01

Maricite NaFePO4 (m-NaFePO4) was investigated as a positive electrode material for intermediate-temperature operation of sodium secondary batteries using ionic liquid electrolytes. Powdered m-NaFePO4 was prepared by a conventional solid-state method at 873 K and subsequently fabricated in two different conditions; one is ball-milled in acetone and the other is re-calcined at 873 K after the ball-milling. Electrochemical properties of the electrodes prepared with the as-synthesized m-NaFePO4, the ball-milled m-NaFePO4, and the re-calcined m-NaFePO4 were investigated in Na[FSA]-[C2C1im][FSA] (C2C1im+ = 1-ethyl-3-methylimidazolium, FSA- = bis(fluorosulfonyl)amide) ionic liquid electrolytes at 298 K and 363 K to assess the effects of temperature and particle size on their electrochemical properties. A reversible charge-discharge capacity of 107 mAh g-1 was achieved with a coulombic efficiency >98% from the 2nd cycle using the ball-milled m-NaFePO4 electrode at a C-rate of 0.1 C and 363 K. Electrochemical impedance spectroscopy using m-NaFePO4/m-NaFePO4 symmetric cells indicated that inactive m-NaFePO4 becomes an active material through ball-milling treatment and elevation of operating temperature. X-ray diffraction analysis of crystalline m-NaFePO4 confirmed the lattice contraction and expansion upon charging and discharging, respectively. These results indicate that the desodiation-sodiation process in m-NaFePO4 is reversible in the intermediate-temperature range.

Gasification of sulphate soap for the lime kiln

Energy Technology Data Exchange (ETDEWEB)

Saviharju, Kari (Valtion Teknillinen Tutkimuskeskus, Espoo (Finland). Lab. of Fuel and Process Technology); Timonen, Tuomas (Finnish Energy Economy Association, Espoo (Finland). Finnish Recovery Boiler Committee)

1993-01-01

Sulphate soap is a by-product of pulp mills utilized as a raw material for the chemical industry. However, this results in an increase in sulphur input of several kilograms SO[sub 2] per ADt pulp into the mill. Another increasingly interesting alternative is to utilize soap in the lime kiln of the mill. This has a positive effect, in addition to sulphur problems, on the energy balance of the mill. The crucial problem is the high Na + K content of soap, from 4 to 8%, which can result in plugging of the lime kiln. The operational problems can be avoided by gasifying the soap and by separating the inorganic materials from the product gas before the kiln. This paper describes research work on the gasification of crude sulphate soap carried out at the Technical Research Centre of Finland (VTT) over the years 1991 and 1992. This work will be continued in 1993 by focusing on specified problems, after which commercial applications should be available. (author)

Detailed investigation of Na2.24FePO4CO3 as a cathode material for Na-ion batteries

Science.gov (United States)

Huang, Weifeng; Zhou, Jing; Li, Biao; Ma, Jin; Tao, Shi; Xia, Dingguo; Chu, Wangsheng; Wu, Ziyu

2014-01-01

Na-ion batteries are gaining an increased recognition as the next generation low cost energy storage devices. Here, we present a characterization of Na3FePO4CO3 nanoplates as a novel cathode material for sodium ion batteries. First-principles calculations reveal that there are two paths for Na ion migration along b and c axis. In-situ and ex-situ Fe K-edge X-ray absorption near edge structure (XANES) point out that in Na3FePO4CO3 both Fe2+/Fe3+ and Fe3+/Fe4+ redox couples are electrochemically active, suggesting also the existence of a two-electron intercalation reaction. Ex-situ X-ray powder diffraction data demonstrates that the crystalline structure of Na3FePO4CO3 remains stable during the charging/discharging process within the range 2.0–4.55 V. PMID:24595232

Study of the Na-C-O and Na-H-O ternary systems in the sodium rich corner

International Nuclear Information System (INIS)

Maupre, J.-P.

1978-02-01

The purpose of this study is to provide a contribution to the understanding of the sodium - carbon - oxygen and sodium - hydrogen - oxygen ternary systems in the sodium rich corner. In order to do this the Na-NaH-Na 2 O-NaOH phase diagram was completed and the Na-Na 2 O-Na 2 CO 3 -C phase diagram was outlined. This work is made up of two parts. The first is devoted to a critical literature survey essential to establish correct phase diagrams. The second is an experimental study followed by a discussion collating our finding to the literary data. The basic experimental technique used is differential thermal analysis (DTA) but it has been completed by quenching, X-ray and chemical analysis methods. The proposed phase diagrams imply that Na-NaH-Na 2 O-NaOH and Na-Na 2 O-Na 2 CO 3 -C systems are reciprocal ternary systems. Temperatures of stable pairs reversal are respectively 410 and 690 0 C. The stable pairs are Na-NaOH and Na-Na 2 CO 3 at elevated temperature, Na 2 O-NaH and Na 2 O-C at low temperature [fr

Beneficial effect of boron in layered sodium-ion cathode materials - The example of Na2/3B0.11Mn0.89O2

Science.gov (United States)

Vaalma, Christoph; Buchholz, Daniel; Passerini, Stefano

2017-10-01

Sodium-ion batteries are regarded as a complementary drop-in technology to lithium-ion batteries because they promise lower cost and a higher degree of environmental friendliness. Among other reasons, these benefits come from the use of manganese-based materials, whose stabilization via cation substitution is intensively studied to improve the electrochemical performance. Although multiple elements have been considered as substituent, surprisingly, boron has not been reported for layered sodium-ion cathode materials up to date. Our investigation of layered Na2/3B0.11Mn0.89O2 reveals an unexpectedly good electrochemical performance, with charge and discharge capacities of more than 175 mAh g-1 at 10 mA g-1 and 135 mAh g-1 at 500 mA g-1. The measured capacities are among the highest ever reported for sodium-based layered oxides in the potential range of 4.0-2.0 V vs. Na/Na+.

Uranium and sulphate values from carbonate leach process

International Nuclear Information System (INIS)

Berger, B.

1983-01-01

The process concerns the recovery of uraniferous and sulphur values from liquor resulting from the attack of sulphur containing uraniferous ores by an alkaline solution of sodium carbonate and/or bicarbonate. Ammonia is introduced into the liquor to convert any HCO 3 - to CO 3 2- . The neutralised liquor from this step is then contacted with an anion exchange resin to fix the uranium and sulphate ions, leaving a liquor containing ammonia, sodium carbonate and/or bicarbonate in solution. Uranium and sulphate ions are eluted with an ammonia carbonate and/or bicarbonate solution to yield a solution of ammonium uranyl carbonate complex and ammonium sulphate. The solution is subjected to thermal treatment until a suspension of precipitated ammonium uranate and/or diuranate is obtained in a solution of the ammonium sulphate. Carbon dioxide, ammonia and water vapor are driven off. The precipitated ammonium uranate and/or diuranate is then separated from the solution of ammonium sulphate and the precipitate is calcined to yield uranium trioxide and ammonia

Development of a glass matrix for vitrification of sulphate bearing high level radioactive liquid waste

International Nuclear Information System (INIS)

Kaushik, C.P.; Mishra, R.K.; Thorat, Vidya; Ramchandran, M.; Amar Kumar; Ozarde, P.D.; Raj, Kanwar; Das, D.

2004-07-01

High level radioactive liquid waste (HLW) is generated during reprocessing of spent nuclear fuel. In the earlier reprocessing flow sheet ferrous sulphamate has been used for valancy adjustment of Pu from IV to III for effective separation. This has resulted in generation of HLW containing significance amount of sulphate. Internationally borosilicate glass matrix has been adopted for vitrification of HLW. The first Indian vitrification facility at Waste Immobilislition Plant (WIP), Tarapur a five component borosilicate matrix (SiO 2 :B 2 O 3 :Na 2 O : MnO : TiO 2 ) has been used for vitrification of waste. However at Trombay HLW contain significant amount of sulphate which is not compatible with standard borosilicate formulation. Extensive R and D efforts were made to develop a glass formulation which can accommodate sulphate and other constituents of HLW e.g., U, Al, Ca, etc. This report deals with development work of a glass formulations for immobilization of sulphate bearing waste. Different glass formulations were studied to evaluate the compatibility with respect to sulphate and other constituents as mentioned above. This includes sodium, lead and barium borosilicate glass matrices. Problems encountered in different glass matrices for containment of sulphate have also been addressed. A glass formulation based on barium borosilicate was found to be effective and compatible for sulphate bearing high level waste. (author)

Effects of Manganese (Ii Sulphate on Structural, Spectral, Optical, Thermal and Mechanical Properties of L-Alanine Sodium Sulphate Single Crystals

Directory of Open Access Journals (Sweden)

F. Praveena

2017-04-01

Full Text Available New Non-linear Optical materials have been attracting in the research world for their potential applications in emerging opto-electronic technology. The dipolar nature of amino acid leads to peculiar physical and chemical properties, thus making a good candidate for NLO applications. Single crystals of manganese(II sulphate doped L-Alanine sodium sulphate(LASS has been synthesized by slow evaporation technique. Structural property of the grown crystals are characterized by X-ray powder diffraction,FT-IR spectral analysis conforms all the functional groups. Thermogravity (TG and differential themogravimetric (DTA analysis have been performed to study the thermal stability of the crystals. The second harmonic generation efficiency was measured by Kurtz-Perry powder technique. The transmission and absorption of electromagnetic radiation is analysed through UV-VIS spectrum. Microhardness was measured at different applied load to understand the mechanical stability of the crystal.

TXNIP mediates the differential responses of A549 cells to sodium butyrate and sodium 4-phenylbutyrate treatment.

Science.gov (United States)

Jin, Xuefang; Wu, Nana; Dai, Juji; Li, Qiuxia; Xiao, XiaoQiang

2017-02-01

Sodium butyrate (NaBu) and sodium 4-phenylbutyrate (4PBA) have promising futures in cancer treatment; however, their underlying molecular mechanisms are not clearly understood. Here, we show A549 cell death induced by NaBu and 4PBA are not the same. NaBu treatment induces a significantly higher level of A549 cell death than 4PBA. A gene expression microarray identified more than 5000 transcripts that were altered (>1.5-fold) in NaBu-treated A549 cells, but fewer than 2000 transcripts that were altered in 4PBA. Moreover, more than 100 cell cycle-associated genes were greatly repressed by NaBu, but slightly repressed by 4PBA; few genes were significantly upregulated only in 4PBA-treated cells. Gene expression was further validated by other experiments. Additionally, A549 cells that were treated with these showed changes in glucose consumption, caspase 3/7 activation and histone modifications, as well as enhanced mitochondrial superoxide production. TXNIP was strongly induced by NaBu (30- to 40-fold mRNA) but was only slightly induced by 4PBA (two to fivefold) in A549 cells. TXNIP knockdown by shRNA in A549 cells significantly attenuated caspase 3/7 activation and restored cell viability, while TXNIP overexpression significantly increased caspase 3/7 activation and cell death only in NaBu-treated cells. Moreover, TXNIP also regulated NaBu- but not 4PBA-induced H4K5 acetylation and H3K4 trimethylation, possibly by increasing WDR5 expression. Finally, we demonstrated that 4PBA induced a mitochondrial superoxide-associated cell death, while NaBu did so mainly through a TXNIP-mediated pathway. The above data might benefit the future clinic application. © 2016 The Authors. Cancer Medicine published by John Wiley & Sons Ltd.

A data base for thermodynamic modeling of +III actinide solubility in concentrated Na-Cl-SO4-CO3-PO4 electrolytes

International Nuclear Information System (INIS)

Novak, C.F.; Crafts, C.C.; Dhooge, N.J.

1995-01-01

The literature contains thermodynamic parameters for describing the chemical behavior of the following: Am(III) in dilute NaHCO 3 media; Nd(III) in dilute to concentrated Na 2 CO 3 and NaHCO 3 media; Pu(III) in dilute to concentrated NaCl media; Nd(III)/Am(III) in dilute to concentrated Na 2 SO 4 media; and Am(III) in NaH 2 PO 4 media. We have combined this information into a thermodynamic data base for the general +III actinide, An(III), using the analogy for chemical behavior of f-elements in the same oxidation state. This internally consistent data base is based on equilibrium thermodynamics and the specific ion interaction activity coefficient formalism of Pitzer. This data base forms the basis for the prediction of potential Am(III) and Pu(III) dissolved concentrations in the concentrated natural brines associated with the Waste Isolation Pilot Plant (WIPP) in Southeastern New Mexico, USA

Distinctly Different Glass Transition Behaviors of Trehalose Mixed with Na2HPO 4 or NaH 2PO 4: Evidence for its Molecular Origin.

Science.gov (United States)

Weng, Lindong; Elliott, Gloria D

2015-07-01

The present study is aimed at understanding how the interactions between sugar molecules and phosphate ions affect the glass transition temperature of their mixtures, and the implications for pharmaceutical formulations. The glass transition temperature (Tg) and the α-relaxation temperature (Tα) of dehydrated trehalose/sodium phosphate mixtures (monobasic or dibasic) were determined by differential scanning calorimetry and dynamic mechanical analysis, respectively. Molecular dynamics simulations were also conducted to investigate the microscopic interactions between sugar molecules and phosphate ions. The hydrogen-bonding characteristics and the self-aggregation features of these mixtures were quantified and compared. Thermal analysis measurements demonstrated that the addition of NaH2PO4 decreased both the glass transition temperature and the α-relaxation temperature of the dehydrated trehalose/NaH2PO4 mixture compared to trehalose alone while both Tg and Tα were increased by adding Na2HPO4 to pure trehalose. The hydrogen-bonding interactions between trehalose and HPO4(2-) were found to be stronger than both the trehalose-trehalose hydrogen bonds and those formed between trehalose and H2PO4(-). The HPO4(2-) ions also aggregated into smaller clusters than H2PO4(-) ions. The trehalose/Na2HPO4 mixture yielded a higher T g than pure trehalose because marginally self-aggregated HPO4(2-) ions established a strengthened hydrogen-bonding network with trehalose molecules. In contrast H2PO4(-) ions served only as plasticizers, resulting in a lower Tg of the mixtures than trehalose alone, creating large-sized ionic pockets, weakening interactions, and disrupting the original hydrogen-bonding network amongst trehalose molecules.

Mixed sodium nickel-manganese sulfates: Crystal structure relationships between hydrates and anhydrous salts

Energy Technology Data Exchange (ETDEWEB)

Marinova, Delyana M.; Zhecheva, Ekaterina N.; Kukeva, Rositsa R.; Markov, Pavel V. [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria); Nihtianova, Diana D. [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria); Institute of Mineralogy and Crystallography, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria); Stoyanova, Radostina K., E-mail: radstoy@svr.igic.bas.bg [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria)

2017-06-15

The present contribution provides new structural and spectroscopic data on the formation of solid solutions between hydrated and dehydrated sulfate salts of sodium-nickel and sodium-manganese in a whole concentration range: Na{sub 2}Ni{sub 1−x}Mn{sub x}(SO{sub 4}){sub 2}·yH{sub 2}O, 0≤ x≤1.0. Using powder XRD, electron paramagnetic resonance spectroscopy (EPR), IR and Raman spectroscopy it has been found that double sodium-nickel and sodium-manganese salts form solid solutions Na{sub 2}Ni{sub 1−x}Mn{sub x}(SO{sub 4}){sub 2}·4H{sub 2}O with a blödite-type of structure within a broad concentration range of 0≤x≤0.49, while the manganese rich compositions Na{sub 2}Ni{sub 1−x}Mn{sub x}(SO{sub 4}){sub 2}·2H{sub 2}O (0.97≤x≤1.0) crystallize in the kröhnkite-type of structure. The Ni-based blödites Na{sub 2}Ni{sub 1−x}Mn{sub x}(SO{sub 4}){sub 2}·4H{sub 2}O dehydrate between 140 and 260 °C into anhydrous salts Na{sub 2}Ni{sub 1−x}Mn{sub x}(SO{sub 4}){sub 2}, 0≤ x≤0.44, with a structure where Ni{sub 1−x}Mn{sub x}O{sub 6} octahedra are bridged into pairs by edge- and corner sharing SO{sub 4}{sup 2−} groups. Both TEM and EPR methods show that the Ni{sup 2+} and Mn{sup 2+} ions are homogenously distributed over three crystallographic positions of the large monoclinic cell. The dehydration of the kröhnkite phase Na{sub 2}Ni{sub 1−x}Mn{sub x}(SO{sub 4}){sub 2}·2H{sub 2}O yields the alluaudite phase Na{sub 2+δ}Mn{sub 2-δ/2}(SO{sub 4}){sub 3}, where the Na-to-Mn ratio decreases and all Ni{sup 2+} dopants are released from the structure. The process of the dehydration is discussed in terms of structural aspects taking into account the distortion degree of the Ni,MnO{sub 6} and SO{sub 4} polyhedra. - Graphical abstract: Thermal dehydration of the blödite phase Na{sub 2}Ni{sub 1−x}Mn{sub x}(SO{sub 4}){sub 2}·4H{sub 2}O (0≤ x≤0.49) yields nickel-manganese sulfates Na{sub 2}Ni{sub 1−x}Mn{sub x}(SO{sub 4}){sub 2} (0≤ x≤0.44) with

Anodic behaviour of the stainless steel AISI 430 in aqueous solutions of chloride and sulphate ions

International Nuclear Information System (INIS)

Sebrao, M.Z.

1982-01-01

The kinetics of the dissolution of stainless steel AISI 430 in the presence of chloride and sulphate ions has been studied in terms of the ion concentration, the pH variation, and the velocity of the working electrode. The experimental method utilized was the potentiostatic anodic polarization, and the reactants used were NaCl and Na 2 SO 4 at room temperature. Atomic Absorption spectrophotometry and Auger Electrons spectroscopy (AES) analyses were made in order to support the interpretation of results obtained by means of the potentiostatic polarization method. (author)

Inactivation of Listeria monocytogenes ATCC 7644 on tomatoes using sodium docecyl sulphate, levulinic acid and sodium hypochlorite solution

Directory of Open Access Journals (Sweden)

E. Mnyandu

2015-06-01

Full Text Available The human pathogen Listeria monocytogenes poses a serious threat to public health. A study was carried out to evaluate the effectiveness of four sanitizers, used individually or combined, against L. monocytogenes ATCC 7644. The contact times for bacteria and sanitizer were varied to 1, 3 and 5 minutes. Levulinic acid, sodium dodecyl sulphate (SDS, sodium hypochlorite solution (chlorine and a combination of SDS and levulinic acid (mixture were tested. Results revealed that 0.5% levulinic acid, when used individually, is capable of reducing the surviving colonies by 3.63 log CFU/mL, 4.05 log CFU/mL, 6.71 log CFU/mL after exposure for 1, 3 and 5 minutes respectively.SDS resulted in an 8 log CFU/mL reduction after 1, 3 and 5 minutes. A combination of 0.5% levulinic acid and 0.05% SDS caused a 3.69 log CFU /mL reduction, 4.4 log CFU/mL reduction, 7.97 log CFU/mL reduction for 1, 3 and 5 minutes respectively. Chlorine was the least effective with 2.93 log CFU/mL reduction, 3.16 log CFU/ mL reduction and 4.53 log CFU/ mL reduction respectively. When stored for up to 72 hours at 4°C, the surviving colonies remained viable and decreased in number significantly P < 0.05 = 0.001. The titratable acidity of samples treated with levulinic acid and samples treated with SDS/Lev mixture was lowered significantly compared to the control sample. No significant differences were noted in these same parameters for samples treated with chlorine or SDS. The application of SDS in the fresh produce industry as a sanitizing agent may be successful in eradicating or reducing the viability of L. monocytogenes on fresh produce, thereby replacing the routine chlorine washing.

Insights into the Dual-Electrode Characteristics of Layered Na0.5Ni0.25Mn0.75O2 Materials for Sodium-Ion Batteries.

Science.gov (United States)

Palanisamy, Manikandan; Kim, Hyun Woo; Heo, Seongwoo; Lee, Eungje; Kim, Youngsik

2017-03-29

Sodium-ion batteries are now close to replacing lithium-ion batteries because they provide superior alternative energy storage solutions that are in great demand, particularly for large-scale applications. To that end, the present study is focused on the properties of a new type of dual-electrode material, Na 0.5 Ni 0.25 Mn 0.75 O 2 , synthesized using a mixed hydroxy-carbonate route. Cyclic voltammetry confirms that redox couples, at high and low voltage ranges, are facilitated by the unique features and properties of this dual-electrode, through sodium ion deintercalation/intercalation into the layered Na 0.5 Ni 0.25 Mn 0.75 O 2 material. This material provides superior performance for Na-ion batteries, as evidenced by the fabricated sodium cell that yielded initial charge-discharge capacities of 125/218 mAh g -1 in the voltage range of 1.5-4.4 V at 0.5 C. At a low voltage range (1.5-2.6 V), the anode cell delivered discharge-charge capacities of 100/99 mAh g -1 with 99% capacity retention, which corresponds to highly reversible redox reaction of the Mn 4+/3+ reduction and the Mn 3+/4+ oxidation observed at 1.85 and 2.06 V, respectively. The symmetric Na-ion cell, fabricated using Na 0.5 Ni 0.25 Mn 0.75 O 2 , yielded initial charge-discharge capacities of 196/187 μAh at 107 μA. These results encourage the further development of new types of futuristic sodium-ion-battery-based energy storage systems.

Distinct interactions of Na+ and Ca2+ ions with the selectivity filter of the bacterial sodium channel NaVAb

International Nuclear Information System (INIS)

Ke, Song; Zangerl, Eva-Maria; Stary-Weinzinger, Anna

2013-01-01

Highlights: ► Ca 2+ translocates slowly in the filter, due to lack of “loose” knock-on mechanism. ► Identification of a high affinity binding site in Na V Ab selectivity filter. ► Changes of EEEE locus triggered by electrostatic interactions with Ca 2+ ions. -- Abstract: Rapid and selective ion transport is essential for the generation and regulation of electrical signaling pathways in living organisms. In this study, we use molecular dynamics simulations and free energy calculations to investigate how the bacterial sodium channel Na V Ab (Arcobacter butzleri) differentiates between Na + and Ca 2+ ions. Multiple nanosecond molecular dynamics simulations revealed distinct binding patterns for these two cations in the selectivity filter and suggested a high affinity calcium binding site formed by backbone atoms of residues Leu-176 and Thr-175 (S CEN ) in the sodium channel selectivity filter

Superconductivity in Na{sub 1-x}CoO{sub 2}.yH{sub 2}O thin films

Energy Technology Data Exchange (ETDEWEB)

Hildebrandt, Sandra; Komissinkiy, Philipp; Alff, Lambert [Institute for Materials Science, TU Darmstadt (Germany); Fritsch, Ingo; Habermeier, Hanns-Ulrich [Max-Planck-Institute for Solid State Research, Stuttgart (Germany); Lemmens, Peter [Institute for Condensed Matter Physics, TU Braunschweig (Germany)

2010-07-01

Sodium cobaltate (Na{sub 1-x}CoO{sub 2}) is a novel material with thermoelectric behavior, charge and spin ordered states dependent on the sodium content in the composition. A superconducting phase was found in water intercalated sodium cobaltate (Na{sub 1-x}CoO{sub 2}.yH{sub 2}O) with x=0.65-0.7 and y=0.9-1.3. The pairing state is still under debate, but there are some indications for a spin-triplet or p-wave superconducting pairing state. First films of Na{sub 1-x}CoO{sub 2}.yH{sub 2}O with a superconducting transition temperature near 5 K have been successfully grown. Here we report on thin films of Na{sub 1-x}CoO{sub 2} grown by pulsed laser deposition technique. The deposition parameters, sodium deintercalation and water intercalation conditions are tuned in order to obtain the superconducting phase. The instability of this phase might be an indication for triplet superconductivity, which is known to be affected strongly by impurities and defects.This observation is in agreement with the fact that so far also no superconducting thin films of the most famous triplet superconductor Sr{sub 2}RuO{sub 4} have been reported.

Thermal expansion studies on Th(MoO4)2, Na2Th(MoO4)3 and Na4Th(MoO4)4

International Nuclear Information System (INIS)

Keskar, Meera; Krishnan, K.; Dahale, N.D.

2008-01-01

Thermal expansion behavior of Th(MoO 4 ) 2 , Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 was studied under vacuum in the temperature range of 298-1123 K by high temperature X-ray diffractometer. Th(MoO 4 ) 2 was synthesized by reacting ThO 2 with 2 mol of MoO 3 , at 1073 K in air and Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 were prepared by reacting Th(MoO 4 ) 2 with 1 and 2 mol of Na 2 MoO 4 , respectively at 873 K in air. The XRD data of Th(MoO 4 ) 2 was indexed on orthorhombic system where as XRD data of Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 were indexed on tetragonal system. The lattice parameters and cell volume of all the three compounds, fit into polynomial expression with respect to temperature, showed positive thermal expansion (PTE) up to 1123 K. The average value of thermal expansion coefficients for Th(MoO 4 ) 2 , Na 2 Th(MoO 4 ) 3 and Na 4 Th(MoO 4 ) 4 were determined from the high temperature data

Revealing isomerism in sodium-water clusters: Photoionization spectra of Na(H2O)n (n = 2-90).

Science.gov (United States)

Dierking, Christoph W; Zurheide, Florian; Zeuch, Thomas; Med, Jakub; Parez, Stanislav; Slavíček, Petr

2017-06-28

Soft ionization of sodium tagged polar clusters is increasingly used as a powerful technique for sizing and characterization of small aerosols with possible application, e.g., in atmospheric chemistry or combustion science. Understanding the structure and photoionization of the sodium doped clusters is critical for such applications. In this work, we report on measurements of photoionization spectra for sodium doped water clusters containing 2-90 water molecules. While most of the previous studies focused on the ionization threshold of the Na(H 2 O) n clusters, we provide for the first time full photoionization spectra, including the high-energy region, which are used as reference for a comparison with theory. As reported in previous work, we have seen an initial drop of the appearance ionization energy with cluster size to values of about 3.2 eV for nphotoionization spectrum. Simulations at elevated temperatures show an increased abundance of isomers with low ionization energies, an entropic effect enabling size selective infrared action spectroscopy, based on near threshold photoionization of Na(H 2 O) n clusters. In addition, simulations of the sodium pick-up process were carried out to study the gradual formation of the hydrated electron which is the basis of the sodium-tagging sizing.

Hydration reactions in pastes C3S+C3A+CaSO4.2aq+H20 at 25°C.I

NARCIS (Netherlands)

Corstanje, W.A.; Stein, H.N.; Stevels, J.M.

1973-01-01

A characteristic retardation of the hydration of C3A is found in pastes C3S+C3A+CaSO4.2aq+H2O of weight ratios 1:3:z:4 at certain values of z, when sulphate concentration becomes insufficient for monosulphate formation. This retardation is ascribed to precipitation of amorphous Al(OH)3, when C3A

Synthesizing Porous NaTi2(PO4)3 Nanoparticles Embedded in 3D Graphene Networks for High-Rate and Long Cycle-Life Sodium Electrodes.

Science.gov (United States)

Wu, Chao; Kopold, Peter; Ding, Yuan-Li; van Aken, Peter A; Maier, Joachim; Yu, Yan

2015-06-23

Sodium ion batteries attract increasing attention for large-scale energy storage as a promising alternative to the lithium counterparts in view of low cost and abundant sodium source. However, the large ion radius of Na brings about a series of challenging thermodynamic and kinetic difficulties to the electrodes for sodium-storage, including low reversible capacity and low ion transport, as well as large volume change. To mitigate or even overcome the kinetic problems, we develop a self-assembly route to a novel architecture consisting of nanosized porous NASICON-type NaTi2(PO4)3 particles embedded in microsized 3D graphene network. Such architecture synergistically combines the advantages of a 3D graphene network and of 0D porous nanoparticles. It greatly increases the electron/ion transport kinetics and assures the electrode structure integrity, leading to attractive electrochemical performance as reflected by a high rate-capability (112 mAh g(-1) at 1C, 105 mAh g(-1) at 5C, 96 mAh g(-1) at 10C, 67 mAh g(-1) at 50C), a long cycle-life (capacity retention of 80% after 1000 cycles at 10C), and a high initial Coulombic efficiency (>79%). This nanostructure design provides a promising pathway for developing high performance NASICON-type materials for sodium storage.

Na3Co2(AsO4(As2O7: a new sodium cobalt arsenate

Directory of Open Access Journals (Sweden)

Abderrahmen Guesmi

2012-07-01

Full Text Available In the title compound, trisodium dicobalt arsenate diarsenate, Na3Co2AsO4As2O7, the two Co atoms, one of the two As and three of the seven O atoms lie on special positions, with site symmetries 2 and m for the Co, m for the As, and 2 and twice m for the O atoms. The two Na atoms are disordered over two general and special positions [occupancies 0.72 (3:0.28 (3 and 0.940 (6:0.060 (6, respectively]. The main structural feature is the association of the CoO6 octahedra in the ab plane, forming Co4O20 units, which are corner- and edge-connected via AsO4 and As2O7 arsenate groups, giving rise to a complex polyhedral connectivity with small tunnels, such as those running along the b- and c-axis directions, in which the Na+ ions reside. The structural model is validated by both bond-valence-sum and charge-distribution methods, and the distortion of the coordination polyhedra is analyzed by means of the effective coordination number.

Oxide-Based Composite Electrolytes Using Na3Zr2Si2PO12/Na3PS4 Interfacial Ion Transfer.

Science.gov (United States)

Noi, Kousuke; Nagata, Yuka; Hakari, Takashi; Suzuki, Kenji; Yubuchi, So; Ito, Yusuke; Sakuda, Atsushi; Hayashi, Akitoshi; Tatsumisago, Masahiro

2018-05-31

All-solid-state sodium batteries using Na 3 Zr 2 Si 2 PO 12 (NASICON) solid electrolytes are promising candidates for safe and low-cost advanced rechargeable battery systems. Although NASICON electrolytes have intrinsically high sodium-ion conductivities, their high sintering temperatures interfere with the immediate development of high-performance batteries. In this work, sintering-free NASICON-based composites with Na 3 PS 4 (NPS) glass ceramics were prepared to combine the high grain-bulk conductivity of NASICON and the interfacial formation ability of NPS. Before the composite preparation, the NASICON/NPS interfacial resistance was investigated by modeling the interface between the NASICON sintered ceramic and the NPS glass thin film. The interfacial ion-transfer resistance was very small above room temperature; the area-specific resistances at 25 and 100 °C were 15.8 and 0.40 Ω cm 2 , respectively. On the basis of this smooth ion transfer, NASICON-rich (70-90 wt %) NASICON-NPS composite powders were prepared by ball-milling fine powders of each component. The composite powders were well-densified by pressing at room temperature. Scanning electron microscopy observation showed highly dispersed sub-micrometer NASICON grains in a dense NPS matrix to form closed interfaces between the oxide and sulfide solid electrolytes. The composite green (unfired) compacts with 70 and 80 wt % NASICON exhibited high total conductivities at 100 °C of 1.1 × 10 -3 and 6.8 × 10 -4 S cm -1 , respectively. An all-solid-state Na 15 Sn 4 /TiS 2 cell was constructed using the 70 wt % NASICON composite electrolyte by the uniaxial pressing of the powder materials, and its discharge properties were evaluated at 100 °C. The cell showed the reversible capacities of about 120 mAh g -1 under the current density of 640 μA cm -2 . The prepared oxide-based composite electrolytes were thus successfully applied in all-solid-state sodium rechargeable batteries without sintering.

Quantitative X-ray spectroscopy of sodium Z-pinch plasmas for Na/ne photopumping

International Nuclear Information System (INIS)

Burkhalter, P.G.; Mehlman, G.; Apruzese, J.P.; Newman, D.A.; Scherrer, V.E.; Young, F.C.; Stephanakis, S.J.; Hinshelwood, D.D.

1990-01-01

Spectra of sodium K-shell x-ray emission were measured for implosions of sodium-bearing plasmas produced on the Naval Research Laboratory Gamble II pulsed-power generator. Sodium fluoride from a capillary discharge provided the initial plasma for these fast Z-pinch implosions. Spatially-resolved images, corresponding to sodium K-shell x-rays from a 3 to 4 cm long plasma column, were recorded with a curved-crystal spectrograph. Non-uniform emission was observed along this column. The diameter of the plasma along the column (1-5 mm) was determined from time-integrated pinhole-camera images, and the duration of the x-ray emission (15-23 ns FWHM) was measured with a vacuum x-ray diode. Absolute emissivities were determined for X-rays from the n=2-1 and n=3-1 transitions in Na X and Na XI. Emissivities calculated using a collisional-radiative equilibrium model were fitted to these measurements to determine plasma temperatures of 230 to 550 eV and electron densities of 0.2 to 4.0 x 10 20 cm -3 at several locations along the plasma column. The slope of the recombination continuum was also used to determine temperatures of 200 to 300 eV and 200 to 400 eV for Na X and Na XI ions, respectively. Absolute intensity measurements of the n=2-1 line emissions from Na X and Na XI, averaged over the entire plasma length, indicated shot-to-shot variations of more than a factor of two in these implosions. (author)

Obtention of agricultural gypsum traced on {sup 34} S (Ca{sup 34} SO{sub 4}.2H{sub 2}O), by chemical reaction between H{sub 2}{sup 34} SO{sub 4} and Ca(OH){sub 2}; Obtencao do gesso agricola marcado no {sup 34} S (Ca{sup 34} SO{sub 4}.2H{sub 2}O), por reacao quimica entre o H{sub 2}{sup 34} SO{sub 4} e Ca(OH){sub 2}

Energy Technology Data Exchange (ETDEWEB)

Rossete, Alessandra L.R.M.; Bendassolli, Jose A.; Ignoto, Raquel de Fatima; Batagello, Hugo Henrique [Centro de Energia Nuclear na Agricultura (CENA), Piracicaba, SP (Brazil). Lab. de Isotopos Estaveis

2002-07-01

The gypsum (CaSO{sub 4}.2H{sub 2}O) has double function in the soil: as source of calcium and sulfur and reducing agent of aluminum saturation. The sulfur for the plants has acting in the vital functions and it is proven fact increase of the S deficiency in Brazilian soils. The isotope tracer {sup 34} S can elucidate important aspects in the sulfur cycle. The Ca{sup 34} SO{sub 4}.2H{sub 2}O was obtained by chemical reaction between Ca(OH){sub 2} and H{sub 2}{sup 34} SO{sub 4} solution. The acid was obtained by chromatography ionic change, using cationic resin Dowex 50WX8 and Na{sub 2}{sup 34} SO{sub 4} solution. The reaction was realized under slow agitation. After the reaction, the precipitate was separated and dried in ventilated stove at 60 deg C temperature. The Mass of the Ca{sup 34} SO{sub 4}.2H{sub 2}O produced was determined by method gravimetric. This way, a system contends resin 426 cm{sup 3}, considering volume of 2.2 liters can be obtained a solution contends 44.2 g of H{sub 2}{sup 34} SO{sub 4}, theoretically could be produced 78.0 g of Ca{sup 34} SO{sub 4}.2H{sub 2}O approximately. With results of the tests were verified that there was not total precipitation of the Ca{sup 34}SO{sub 4}.2H{sub 2}O. Were produced 73.7{+-} 0.6 g of Ca{sup 34} SO{sub 4}.2H{sub 2}O representing average income 94.6{+-}0.8 %. The purity of the produced CaSO{sub 4}.2H{sub 2}O was 98%. (author)

Sodium-NaK engineering handbook. Volume III. Sodium systems, safety, handling, and instrumentation. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Foust, O J [ed.

1978-01-01

The handbook is intended for use by present and future designers in the Liquid Metals Fast Breeder Reactor (LMFBR) Program and by the engineering and scientific community performing other type investigation and exprimentation requiring high-temperature sodium and NaK technology. The arrangement of subject matter progresses from a technological discussion of sodium and sodium--potassium alloy (NaK) to discussions of varius categories and uses of hardware in sodium and NaK systems. Emphasis is placed on sodium and NaK as heat-transport media. Sufficient detail is included for basic understanding of sodium and NaK technology and of technical aspects of sodium and NaK components and instrument systems. Information presented is considered adequate for use in feasibility studies and conceptual design, sizing components and systems, developing preliminary component and system descriptions, identifying technological limitations and problem areas, and defining basic constraints and parameters.

Structural, electrical conductivity and dielectric behavior of Na2SO4–LDT composite solid electrolyte

Directory of Open Access Journals (Sweden)

Mohd Z. Iqbal

2016-01-01

Full Text Available A series of composite materials of general molecular formula (1 − x Na2SO4 − (x LDT was prepared by solid state reaction method. The phase structure and functionalization of these materials were defined by X-ray diffraction (XRD and Fourier-transform infrared spectroscopy (FT-IR respectively. Differential thermal analysis (DTA revealed that the hump of phase transition at 250 °C has decreased while its thermal stability was enhanced. Scanning electron microscopy signifies the presence of improved rigid surfaces and interphases that are accountable for the high ionic conduction due to dispersion of LDT particles in the composite systems. Arrhenius plots of the conductance show the maximum conductivity, σ = 4.56 × 10−4 S cm−1 at 500 °C for the x = 0.4 composition with the lowest activation energy 0.34 eV in the temperature range of 573–773 K. The value of dielectric constant was decreased with increasing frequency and follows the usual trend.

Synthesis and characterization of sodium vanadium oxide gels: the effects of water (n) and sodium (x) content on the electrochemistry of Na(x)V2O5·nH2O.

Science.gov (United States)

Lee, Chia-Ying; Marschilok, Amy C; Subramanian, Aditya; Takeuchi, Kenneth J; Takeuchi, Esther S

2011-10-28

Sodium vanadium oxide gels, Na(x)V(2)O(5)·nH(2)O, of varying sodium content (0.12 n > 0.01) and interlayer spacing were found to be inversely proportional to the sodium level (x), thus control of sodium (x) content provided a direct, chimie douce approach for control of hydration level (n) and interlayer spacing, without the need for high temperature treatment to affect dehydration. Notably, the use of high temperatures to modify hydration levels can result in crystallization and collapse of the interlayer structure, highlighting the distinct advantage of our novel chimie douce synthesis strategy. Subsequent to synthesis and characterization, results from an electrochemical study of a series of Na(x)V(2)O(5)·nH(2)O samples highlight the significant impact of interlayer water on delivered capacity of the layered materials. Specifically, the sodium vanadium oxide gels with higher sodium content and lower water content provided higher capacities in lithium based cells, where capacity delivered to 2.0 V under C/20 discharge ranged from 170 mAh/g for Na(0.12)V(2)O(5)·0.23H(2)O to 300 mAh/g for Na(0.32)V(2)O(5)·0.01H(2)O. The capacity differences were maintained as the cells were cycled. This journal is © the Owner Societies 2011

Preparation, characterization and CO{sub 2} gas sensitivity of Polyaniline doped with Sodium Superoxide (NaO{sub 2})

Energy Technology Data Exchange (ETDEWEB)

Barde, R.V., E-mail: rajeshbarde1976@gmail.com

2016-01-15

Highlights: • NaO{sub 2} prepared in single step method from NaNO{sub 3} in oxygen rich environment. • The sensors show better performance towards the CO{sub 2}. • A significant sensitivity and fast response toward of CO{sub 2} is observed. • Sensing response assign to transition from n-type to p-type behavior of samples. - Abstract: The sodium superoxide was prepared in single step method by heating sodium nitrate (NaNO{sub 3}) in oxygen rich environment. The PANi/NaO{sub 2} composites were prepared using Ex-situ technique range from 5–20 wt.%. The crystallinity and structure morphology of the PANi/ NaO{sub 2} composite films were characterized by X-ray diffraction, Scanning electron microscopy and Fourier transform infrared spectroscopy respectively. The sensor response was estimated by the change in electrical resistance of sensor in presence of CO{sub 2} gas. The sensor response and selectivity for pure PANi and doped PANi/NaO{sub 2} sensors as a function of concentration of CO{sub 2} at room temperature has been systematically studied. The sensors show better performance towards the CO{sub 2}. A significant sensitivity and fast response toward CO{sub 2} observed for the 20 wt.% PANi/NaO{sub 2} composite film. The sensing response curve assign to transition from n-type to p-type behavior of samples.

Revealing isomerism in sodium-water clusters: Photoionization spectra of Na(H2O)n (n = 2-90)

Science.gov (United States)

Dierking, Christoph W.; Zurheide, Florian; Zeuch, Thomas; Med, Jakub; Parez, Stanislav; Slavíček, Petr

2017-06-01

Soft ionization of sodium tagged polar clusters is increasingly used as a powerful technique for sizing and characterization of small aerosols with possible application, e.g., in atmospheric chemistry or combustion science. Understanding the structure and photoionization of the sodium doped clusters is critical for such applications. In this work, we report on measurements of photoionization spectra for sodium doped water clusters containing 2-90 water molecules. While most of the previous studies focused on the ionization threshold of the Na(H2O)n clusters, we provide for the first time full photoionization spectra, including the high-energy region, which are used as reference for a comparison with theory. As reported in previous work, we have seen an initial drop of the appearance ionization energy with cluster size to values of about 3.2 eV for n electron cloud. The appearance ionization energy is determined by isomers with fully solvated sodium and a highly delocalized electron cloud, while both fully and incompletely solvated isomers with localized electron clouds can contribute to the high energy part of the photoionization spectrum. Simulations at elevated temperatures show an increased abundance of isomers with low ionization energies, an entropic effect enabling size selective infrared action spectroscopy, based on near threshold photoionization of Na(H2O)n clusters. In addition, simulations of the sodium pick-up process were carried out to study the gradual formation of the hydrated electron which is the basis of the sodium-tagging sizing.

Exacerbation of alopecia areata: A possible complication of sodium tetradecyl sulphate foam sclerotherapy treatment for varicose veins

OpenAIRE

Whiteley, Mark S; Smith, Victoria C

2017-01-01

A 40-year-old woman with a history of alopecia areata related to stress or hormonal changes was treated for bilateral primary symptomatic varicose veins (CEAP clinical score C2S) of pelvic origin, using a staged procedure. Her first procedure entailed pelvic vein embolisation of three pelvic veins using 14 coils and including foam sclerotherapy of the tributaries, using 3% sodium tetradecyl sulphate. Following this procedure, she had an exacerbation of alopecia areata with some moderate shedd...

Synthesis, crystal structure, electrical properties, and sodium transport pathways of the new arsenate Na{sub 4}Co{sub 7}(AsO{sub 4}){sub 6}

Energy Technology Data Exchange (ETDEWEB)

Ben Smida, Youssef; Marzouki, Riadh [Université de Tunis El Manar, Laboratoire de Matériaux et Cristallochimie, Faculté des Sciences de Tunis, Campus Universitaire, 2092 Manar II, Tunis (Tunisia); Georges, Samuel [Université Grenoble Alpes, Laboratoire d’Electrochimie et de Physicochimie des Matériaux et des Interfaces LEPMI, F-38000 Grenoble (France); Kutteh, Ramzi [Bragg Institute, Australian Nuclear Science and Technology Organisation (ANSTO), New Illawarra Road, Lucas Heights, New South Wales 2234 (Australia); Avdeev, Maxim [Bragg Institute, Australian Nuclear Science and Technology Organisation (ANSTO), New Illawarra Road, Lucas Heights, New South Wales 2234 (Australia); School of Chemistry, University of Sydney, Sydney, New South Wales 2006 (Australia); Guesmi, Abderrahmen; Zid, Mohamed Faouzi [Université de Tunis El Manar, Laboratoire de Matériaux et Cristallochimie, Faculté des Sciences de Tunis, Campus Universitaire, 2092 Manar II, Tunis (Tunisia)

2016-07-15

A new sodium cobalt (II) arsenate Na{sub 4}Co{sub 7}(AsO{sub 4}){sub 6} has been synthesized by a solid-state reaction and its crystal structure determined from single crystal X-ray diffraction data. It crystallizes in the monoclinic system, space group C2/m, with a=10.7098(9) Å, b=14.7837(9) Å, c=6.6845(7) Å, and β=105.545(9)°. The structure is described as a three-dimensional framework built up of corner-edge sharing CoO{sub 6}, CoO{sub 4} and AsO{sub 4} polyhedra, with interconnecting channels along [100] in which the Na{sup +} cations are located. The densest ceramics with relative density of 94% was obtained by ball milling and optimization of sintering temperature, and its microstructure characterized by scanning electron microscopy. The electrical properties of the ceramics were studied over a temperature interval from 280 °C to 560 °C using the complex impedance spectroscopy over the range of 13 MHz–5 Hz. The ionic bulk conductivity value of the sample at 360 °C is 2.51 10{sup −5} S cm{sup −1} and the measured activation energy is Ea=1 eV. The sodium migration pathways in the crystal structure were investigated computationally using the bond valence site energy (BVSE) model and classical molecular dynamics (MD) simulations. - Graphical abstract: Correlation between crystal structure, microstructure and ionic conductivity . Display Omitted - Highlights: • A new arsenate Na{sub 4}Co{sub 7}(AsO{sub 4}){sub 6} was prepared by solid state reaction. • Its crystal structure was determined by powder X-ray diffraction. • Na{sup +} ionic conductivity was probed by complex impedance spectroscopy. • Na{sup +} conduction pathways were modeled by bond-valence method and molecular dynamics.

K0.78Na0.22MoO2AsO4

Directory of Open Access Journals (Sweden)

Ahmed Driss

2013-08-01

Full Text Available The title compound, potassium sodium dioxidomolybdenum(VI arsenate, K0.78Na0.22MoO2AsO4, was synthesized by a solid-state reaction route. The structure is built up from corner-sharing MoO6 octahedra and AsO4 tetrahedra, creating infinite [MoAsO8]∞ chains running along the b-axis direction. As, Mo and all but one O atom are on special positions (4c with m symmetry and K (occupancy 0.78 is on a position (4a of -1 in the tunnels. The possible motion of the alkali cations has been investigated by means of the bond-valance sum (BVS model. The simulation shows that the Na+ motion appears to be easier mainly along the b-axis direction. Structural relationships between the different compounds of the AMoO2AsO4 (A = Ag, Li, Na, K, Rb series and MXO8 (M = V; X = P, As chains are discussed.

Ternary phosphates in Ca3(PO4)2-Na3Ln(PO4)2 (Ln-Nd, Eu, Er) systems

International Nuclear Information System (INIS)

Lazoryak, B.I.; Ivanov, L.N.; Strunenkova, T.V.; Golubev, V.N.; Viting, B.N.

1990-01-01

Ternary phosphates, formed in Ca 3 (PO 4 ) 2 -Na 3 Ln(PO 4 ) 2 (Ln-Nd, Eu, Er) systems were investigated by the methods of X-ray phase, luminescent analyses and IR spectroscopy. 5 regions of homogeneity were found. Two of them (I and II) were distinguished for all systems. Samples in the region of up to 14.285 mol.% Na 3 Ln(PO 4 ) 2 crystallize on the basis of β-Ca 3 (PO 4 ) 2 structure, and in other homogeneity regions - on the basis of β-K 2 SO 4 structure

Electrochemical migration of lead-free solder alloys in Na2SO4 environment

DEFF Research Database (Denmark)

Medgyes, Balint; Ádám, Sándor; Tar, Lajos

2017-01-01

The effect of sulphate ion concentration on electrochemical migration of lead-free solder alloys was investigated with the use of water drop tests, by applying an in-situ optical and electrical inspection system. According to the Mean-Time-To-Failure (MTTF) values it was found that in the case of...

Forest land cover continues to exacerbate freshwater acidification despite decline in sulphate emissions

International Nuclear Information System (INIS)

Dunford, Robert W.; Donoghue, Daniel N.M.; Burt, Tim P.

2012-01-01

Evidence from a multi-date regional-scale analysis of both high-flow and annual-average water quality data from Galloway, south-west Scotland, demonstrates that forest land cover continues to exacerbate freshwater acidification. This is in spite of significant reductions in airborne pollutants. The relationship between freshwater sulphate and forest cover has decreased from 1996 to 2006 indicating a decrease in pollutant scavenging. The relationship between forest cover and freshwater acidity (pH) is, however, still present over the same period, and does not show conclusive signs of having declined. Furthermore, evidence for forest cover contributing to a chlorine bias in marine ion capture suggests that forest scavenging of sea-salts may mean that the forest acidification effect may continue in the absence of anthropogenic pollutant inputs, particularly in coastal areas. - Highlights: ► Forest cover and water chemistry remain linked despite decreased sulphate emissions. ► Forest cover has significant relationships SO 4 2− , Cl − , Na + , pH, ANC and Na:Cl ratio. ► Forest cover: pH relationships shows some evidence of decline 1996–2006. ► Forest cover: freshwater sulphate relationships show evidence of decline 1996–2006. ► Natural forest-mechanisms may exacerbate acidification, particularly sea-salt scavenging. - Relationships between forest land cover and freshwater pH continue to be evident despite declines in anthropogenic pollutant sulphate deposition; sea-salt scavenging may play a role.

Sulphate removal from uraniferous liquors

International Nuclear Information System (INIS)

Berger, B.

1983-01-01

A process for the recovery of uranium from liquor resulting from the attack of sulphur containing uraniferous ores by an alkaline solution of sodium carbonate and/or sodium bicarbonate is claimed. An ion exchange resin is used to separate the uranium from the solution of sodium carbonate and/or bicarbonate and sodium sulphate. The ion exchange resin is then eluted with a solution of ammonium carbonate and/or bicarbonate to provide an eluate containing ammonium uranyl tricarbonate, ammonium carbonate and/or bicarbonate and ammonium sulphate. The eluate is heated to boiling to convert the ammonium uranyl tricarbonate to ammonium uranate and/or diuranate. Ammonia, carbon dioxide and water vapor are released. The precipitated ammonium uranate and/or diuranate is separated from the remaining liquor and calcined to give uranium trioxide

Effects of Potassium Sulfate [K2SO4] on The Element Contents, Polyphenol Content, Antioxidant and Antimicrobial Activities of Milk Thistle [Silybum Marianum].

Science.gov (United States)

Yaldiz, Gulsum

2017-01-01

potassium application [120 kg ha -1 extract, all extracts showed high and similar DPPH scavenging activity. The highest phenolic compounds were obtained with 30 kg ha -1 of K 2 SO 4 , whereas the use of 60 kg ha -1 caused the highest total flavonoid content. This plant is a good source of K + , Ca +2 , PO4 -3 , and Cl -1 . In this study, increasing doses of potassium sulfate had significant effect on element, polyphenol content, antioxidant and antimicrobial activities of the milk thistle. All tested extracts were active against all tested microbial species.All extracts have shown high and similar DPPH scavenging activity.There was a gradual increase in the biological properties of the milk thistle seeds with rising levels of potassium sulfate.The milk thistle seeds are rather rich sources of K + , Ca +2 , PO4 -3 and Cl -1 potentially bioavailable for human consumption. Abbreviations used: AlCl 3 : aluminum chloride, Ca +2 : calcium, Cl - : chloride, Cr: chromium CE: catechol equivalents, DPPH: 2,2-diphenylpicrylhydrazyl, ABTS: 2,2'-azino-bis-3-ethylbenzthiazoline-6-sulphonic acid, DAP: diamonyum fosfat, F - : fluoride, Fe: iron, K 2 SO 4 : potassium sulfate, K+ : potassium, Li+: lithium, Mg +2 : magnesium, NH 4 + : amonyum, Na + : sodium, NO 2 - : nitrite, NO 3 - : nitrate, Ni: nickel, NaNO 2 : sodium nitrite, NaOH: sodium hidroksit. ND: Not detectable, PO4 -3 : phosphorus, Zn: zinc.

Preparation of {sup 35}SO{sub 4}H{sub 2} and of some other {sup 35}S labeled mineral compounds; Preparation de {sup 35}SO{sub 4}H{sub 2} et de quelques autres composes mineraux simples marques a {sup 35}S

Energy Technology Data Exchange (ETDEWEB)

De la Gueronniere, E; Henry, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

Methods of preparation, from pile irradiated KCI, of the following labeled molecules are described: - carrier free H{sub 2}SO{sub 4} - SCd (100 m curies/milli mole) - solution of SNa{sub 2} (100 m curies/milli mole) - solution of SK{sub 2} (100 m curies/milli mole) - S metalloid (100 m curies/milli mole) - SO{sub 3}Na{sub 2} (90 m curies/milli mole) - S{sub 2}C{sub 3}Na{sub 2} (50 m curies/mammalia). (author) [French] On decrit les methodes de preparation, a partir de KCl irradie dans les piles, des molecules suivantes marquees au {sup 35}S: - SO{sub 4}H{sub 2} (sans entraineur) - SCd (100 mcuries/millimole) - solution de SNa{sub 2} (100 mcuries/millimole) - solution de SK{sub 2} (100 mcuries/millimole) - S metalloide (100 mcuries/millimole) - Na{sub 2}SO{sub 3} (90 mcuries/millimole) - Na{sub 2}S{sub 2}C{sub 3} (50 mcuries/milIimole). (auteur)

Investigation into the role of sodium chloride deposited on oxide and metal substrates in the initiation of hot corrosion

Science.gov (United States)

Birks, N.

1983-01-01

Sodium chloride is deposited on the surface of alumina substrates and exposed to air containing 1% SO2 at temperatures between 500 C and 700 C. In all cases the sodium chloride was converted to sodium sulfate. The volatilization of sodium chloride from the original salt particles was responsible for the development of a uniform coating of sodium sulfate on the alumina substrate. At temperatures above 625 C, a liquid NaCl-Na2SO4 autectic was formed on the substrate. The mechanisms for these reactions are given. One of the main roles of NaCl in low temperature hot corrosion lies in enabling a corrosive liquid to form.

Unravelling the origin of irreversible capacity loss in NaNiO 2 for high voltage sodium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Wang, Liguang; Wang, Jiajun; Zhang, Xiaoyi; Ren, Yang; Zuo, Pengjian; Yin, Geping; Wang, Jun

2017-04-01

Layered transition metal compounds have attracted much attention due to their high theoretical capacity and energy density for sodium ion batteries. However, this kind of material suffers from serious irreversible capacity decay during the charge and discharge process. Here, using synchrotron-based operando transmission X-ray microscopy and high-energy X-ray diffraction combined with electrochemical measurements, the visualization of the dissymmetric phase transformation and structure evolution mechanism of layered NaNiO2 material during initial charge and discharge cycles are clarified. Phase transformation and deformation of NaNiO2 during the voltage range of below 3.0 V and over 4.0 V are responsible for the irreversible capacity loss during the first cycling, which is also confirmed by the evolution of reaction kinetics behavior obtained by the galvanostatic intermittent titration technique. These findings reveal the origin of the irreversibility of NaNiO2 and offer valuable insight into the phase transformation mechanism, which will provide underlying guidance for further development of high-performance sodium ion batteries.

Solubility of NaNd(CO3)2.6H2O(c) in concentrated Na2CO3 and NaHCO3 solutions

International Nuclear Information System (INIS)

Rao, L.; Rai, D.; Felmy, A.R.; Fulton, R.W.; Novak, C.F.

1996-01-01

NaNd(CO 3 ) 2 x 6 H 2 O(c) was identified to be the final equilibrium solid phase in suspensions containing concentrated sodium carbonate (0.1 to 2.0 M) and sodium bicarbonate (0.1 to 1.0 M), with either NaNd(CO 3 ) 2 x 6 H 2 O(c) or Nd 2 (CO 3 ) 3 x xH 2 O(s) as initial solids. A thermodynamic model, based on Pitzer's specific into-interaction approach, was developed to interpret the solubility of NaNd(CO 3 ) 2 x 6 H 2 O(c) as functions of sodium carbonate and sodium bicarbonate concentrations. In this model, the solubility data of NaNd(CO 3 ) 2 x 6 H 2 O(c) were explained by assuming the formation of NdCO 3 + , Nd(CO 3 ) 2 - and Nd(CO 3 ) 3 3- species and invoking the specific ion interactions between Na + and Nd(CO 3 ) 3 3- . Ion interaction parameters for Na + -Nd(CO 3 ) 3 3- were developed to fit the solubility data. Based on the model calculations, Nd(CO 3 ) 3 3- was the predominant aqueous neodymium species in 0.1 to 2 M sodium carbonate and 0.1 to 1 M sodium bicarbonate solutions. The logarithm of the NaNd(CO 3 ) 2 x 6 H 2 O solubility product (NaNd(CO 3 ) 2 x 6 H 2 O(c)=Na + +Nd 3+ +2 CO 3 2- +6 H 2 O) was calculated to be -21.39. This model also provided satisfactory interpretation of the solubility data of the analogous Am(III) system in less concentrated carbonate and bicarbonate solutions. (orig.)

Treatment for GaSb surfaces using a sulphur blended (NH{sub 4}){sub 2}S/(NH{sub 4}){sub 2}SO{sub 4} solution

Energy Technology Data Exchange (ETDEWEB)

Murape, D.M., E-mail: Davison.Murape@nmmu.ac.za [Department of Physics, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth, 6031 (South Africa); Eassa, N.; Neethling, J.H. [Department of Physics, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth, 6031 (South Africa); Betz, R. [Department of Chemistry, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth, 6031 (South Africa); Coetsee, E.; Swart, H.C. [Department of Physics, University of the Free State, PO Box 339, Bloemfontein, 9300 (South Africa); Botha, J.R.; Venter, A. [Department of Physics, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth, 6031 (South Africa)

2012-07-01

A sulphur based chemical, [(NH{sub 4}){sub 2}S/(NH{sub 4}){sub 2}SO{sub 4}] to which S has been added, not previously reported for the treatment of (1 0 0) n-GaSb surfaces, is introduced and benchmarked against the commonly used passivants Na{sub 2}S{center_dot}9H{sub 2}O and (NH{sub 4}){sub 2}S. The surfaces of the treated material were studied by scanning electron microscopy (SEM), Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). It has been found that the native oxides present on the GaSb surface are more effectively removed when treated with ([(NH{sub 4}){sub 2}S/(NH{sub 4}){sub 2}SO{sub 4}] + S) than with (NH{sub 4}){sub 2}S or Na{sub 2}S{center_dot}9H{sub 2}O, as evidenced by the ratio of the O{sub 506eV} to Sb{sub 457eV} AES peaks. XPS results reveal that Sb{sub 2}S{sub 3}/Sb{sub 2}S{sub 5} 'replaces' Sb{sub 2}O{sub 3}/Sb{sub 2}O{sub 5}, suggesting that sulphur atoms substitute oxygen atoms in Sb{sub 2}O{sub 3}/Sb{sub 2}O{sub 5} to form Sb-S. It seems sulphurization only partially removes Ga{sub 2}O{sub 3}. Treatment with ([(NH{sub 4}){sub 2}S/(NH{sub 4}){sub 2}SO{sub 4}] + S) also results in a noteworthy improvement in the current-voltage (I-V) characteristics of Au/n-GaSb Schottky contacts compared to those fabricated on as-received material.

Size-differentiated composition of inorganic atmospheric aerosols of both marine and polluted continental origin

Science.gov (United States)

Harrison, Roy M.; Pio, Casimiro A.

Atmospheric aerosols were sampled with a high volume impactor/diffusion battery system and the collected fractions analysed for their major water-soluble inorganic constituents. Sulphate, nitrate and chloride showed bimodal distributions; sulphate and nitrate were mainly associated with NH 4+, having approximately log-normal distributions with modes at 1.0 μm. In unpolluted maritime air, chlorides appeared as salts of sodium and magnesium with average modes at c. 5 μm, whilst in polluted air masses significant concentrations of ammonium chloride sub-μm aerosols were detected. Sodium nitrate and sodium sulphate aerosols having average modes of c. 3.5 μm were observed in mixed maritime/polluted air masses. The dimensions of these particles indicate formation from absorption of H 2SO 4 and HNO 3 at the surface of marine NaCl particles. The concentration of H + was very low, but the possibility of its neutralization by atmospheric ammonia during sampling was ruled out by parallel air sampling using an 'ammonia denuder'.

The role of annealing: effect on CaSO4:Dy phosphor with manganese and sodium impurities

International Nuclear Information System (INIS)

Li, S.-H.; Hsu, P.-C.

1990-01-01

The effect of the annealing treatment on the CaSO 4 :Dy phosphor with Mn and Na impurities was studied at different annealing temperatures from 100 0 C to 800 0 C. Doping with or without impurity caused no difference in the properties for temperatures less than 400 0 C. An annealing temperature greater than 400 0 C brings a reduction in low temperature peak intensities of CaSO 4 :Dy with Na only. The high temperature peak intensities increase as the temperature increases from 400 0 C to 600 0 C. However, annealing at a temperature greater than 600 0 C brings a drastic reduction in high temperature peak intensities as well as TL output. (author)

The electrical and thermal properties of sodium sulfate mixed with lithium sulfate, yttrium sulfate, and silicon dioxide

International Nuclear Information System (INIS)

Imanaka, N.; Yamaguchi, Y.; Adachi, G.; Shiokawa, J.

1986-01-01

Sodium sulfate mixed with lithium sulfate, yttrium sulfate, and silicon dioxide was prepared. The thermal and electrical properties of its phases were investigated. The Na 2 SO 4 -Li 2 SO 4 -Y 2 (SO 4 ) 3 SiO 2 samples are similar to the Na 2 SO 4 -I phase (a high temperature phase), which is appreciably effective for Na + ionic conduction. Phase transformation was considerably suppressed by mixing. Electromotive force (EMF) was measured, using Na 2 SO 4 -Li 2 SO 4 -Y 2 (SO 4 ) 3 -SiO 2 as a solid electrolyte, by constructing an SO 2 gas concentration cell. The measured EMF's at 823 and 773 K were in fairly good accordance with the calculated EMF's for inlet SO 2 gas concentration between 30 ppm and 1%, and 500 ppm and 0.5% respectively

Possibilities of Sulphate Elimination from Mine Water

Directory of Open Access Journals (Sweden)

Heviánková Silvie

2004-12-01

Full Text Available The issue of „acid water“ (or AMD is well known in the world for some centuries. In the Eastern Slovakia, the most acid surface water occurs in the area of old mine Smolník, which is closed and submerged for 15 years. The submitted contribution deals with the sulphate-elimination from this locality. Recently, several methods of sulphate-elimination from the mine water are applied. The best-known methods are biological, physical-chemical and chemical precipitation. The method described in this contribution consists of chemical precipitation by sodium aluminate and calcium hydrate. Under application of this method very interesting results were obtained. The amount of SO42- anions decreased to almost zero-value, using optimal doses of the chemical reagents.

Sorption behaviour of uranium and thorium on hydrons tin oxide from aqueous and mixed-solvent H2SO4 media

International Nuclear Information System (INIS)

Misak, N.Z.; Salema, H.N.; El-Naggar, J.M.

1983-01-01

At pH values > about 2 in 10 -3 -10 -2 M aqueous sulphate solutions, uranium seems to be sorbed by hydrous tin oxide mainly as cations, while thorium is sorced as cations and as the neutral complex. At pH values of about 1.1-1.4, both uranium and thorium seem to be mainly sorbed as the neutral complexes. while at lower pH values, sorption of anionic commplexes comes into play. The sorption of uranium generally increased progressively on addition of increasing amounts of methanol, ethanol or acetone. The sorption of thorium decreases a little at 0.01 N H 2 SO 4 and increases a little at 0.5 N H 2 SO 4 on adding the organic solvents. At 0.1 N H 2 SO 4 , the addition of 20percent of the organic solvents brings the sorption of thorium to almost negligible values, which seems to offer an attractive means for U/Th separation. (author)

Protein kinase C-mediated ATP stimulation of Na(+)-ATPase activity in LLC-PK1 cells involves a P2Y2 and/or P2Y4 receptor.

Science.gov (United States)

Wengert, M; Ribeiro, M C; Abreu, T P; Coutinho-Silva, R; Leão-Ferreira, L R; Pinheiro, A A S; Caruso-Neves, C

2013-07-15

ATP-activated P2Y receptors play an important role in renal sodium excretion. The aim of this study was to evaluate the modulation of ATPase-driven sodium reabsorption in the proximal tubule by ATP or adenosine (Ado). LLC-PK1 cells, a model of porcine proximal tubule cells, were used. ATP (10(-6)M) or Ado (10(-6)M) specifically stimulated Na(+)-ATPase activity without any changes in (Na(+)+K(+))-ATPase activity. Our results show that the Ado effect is mediated by its conversion to ATP. Furthermore, it was observed that the effect of ATP was mimicked by UTP, ATPγS and 2-thio-UTP, an agonist of P2Y2 and P2Y4 receptors. In addition, ATP-stimulated Na(+)-ATPase activity involves protein kinase C (PKC). Our results indicate that ATP-induced stimulation of proximal tubule Na(+)-ATPase activity is mediated by a PKC-dependent P2Y2 and/or P2Y4 pathway. These findings provide new perspectives on the role of the effect of P2Y-mediated extracellular ATP on renal sodium handling. Copyright © 2013 Elsevier Inc. All rights reserved.

Analysis of aqueous humour in uveitis by high performance liquid chromatography and sodium dodecyl sulphate-polyacrylamide gel electrophoresis

NARCIS (Netherlands)

Murray, P. I.; Hoekzema, R.; Luyendijk, L.; Kijlstra, A.

1992-01-01

Aqueous humour from patients with Fuchs' heterochromic cyclitis (FHC) and other types of uveitis was analysed by high performance liquid chromatography (HPLC) and sodium dodecyl sulphate-polyacrylamide gel electrophoresis (SDS-PAGE). Using HPLC, the number of peaks and their respective elution times

Robust high pressure stability and negative thermal expansion in sodium-rich antiperovskites Na{sub 3}OBr and Na{sub 4}OI{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Wang, Yonggang, E-mail: yyggwang@gmail.com, E-mail: yangwg@hpstar.ac.cn, E-mail: yusheng.zhao@unlv.edu [High Pressure Science and Engineering Center, University of Nevada, Las Vegas, Nevada 89154 (United States); Institute of Nanostructured Functional Materials, Huanghe Science and Technology College, Zhengzhou, Henan 450006 (China); High Pressure Synergetic Consortium (HPSynC), Geophysical Laboratory, Carnegie Institution of Washington, Argonne, Illinois 60439 (United States); Wen, Ting [Institute of Nanostructured Functional Materials, Huanghe Science and Technology College, Zhengzhou, Henan 450006 (China); Park, Changyong; Kenney-Benson, Curtis [High Pressure Collaborative Access Team (HPCAT), Geophysical Laboratory, Carnegie Institution of Washington, Argonne, Illinois 60439 (United States); Pravica, Michael; Zhao, Yusheng, E-mail: yyggwang@gmail.com, E-mail: yangwg@hpstar.ac.cn, E-mail: yusheng.zhao@unlv.edu [High Pressure Science and Engineering Center, University of Nevada, Las Vegas, Nevada 89154 (United States); Yang, Wenge, E-mail: yyggwang@gmail.com, E-mail: yangwg@hpstar.ac.cn, E-mail: yusheng.zhao@unlv.edu [High Pressure Synergetic Consortium (HPSynC), Geophysical Laboratory, Carnegie Institution of Washington, Argonne, Illinois 60439 (United States); Center for High Pressure Science and Technology Advanced Research (HPSTAR), Shanghai 201203 (China)

2016-01-14

The structure stability under high pressure and thermal expansion behavior of Na{sub 3}OBr and Na{sub 4}OI{sub 2}, two prototypes of alkali-metal-rich antiperovskites, were investigated by in situ synchrotron X-ray diffraction techniques under high pressure and low temperature. Both are soft materials with bulk modulus of 58.6 GPa and 52.0 GPa for Na{sub 3}OBr and Na{sub 4}OI{sub 2}, respectively. The cubic Na{sub 3}OBr structure and tetragonal Na{sub 4}OI{sub 2} with intergrowth K{sub 2}NiF{sub 4} structure are stable under high pressure up to 23 GPa. Although being a characteristic layered structure, Na{sub 4}OI{sub 2} exhibits nearly isotropic compressibility. Negative thermal expansion was observed at low temperature range (20–80 K) in both transition-metal-free antiperovskites for the first time. The robust high pressure structure stability was examined and confirmed by first-principles calculations among various possible polymorphisms qualitatively. The results provide in-depth understanding of the negative thermal expansion and robust crystal structure stability of these antiperovskite systems and their potential applications.

Model study of initial adsorption of SO2 on calcite and dolomite

International Nuclear Information System (INIS)

Malaga-Starzec, Katarina; Panas, Itai; Lindqvist, Oliver

2004-01-01

The rate of calcareous stone degradation is to a significant extent controlled by their surface chemistry with SO 2 . Initial surface sulphite is converted to a harmful gypsum upon, e.g. NO 2 catalysed oxidation. However, it has been observed by scanning electron microscopy that the lateral distributions of gypsum crystals differ between calcitic and dolomitic marbles. The first-principles density functional theory is employed to understand the origin of these fundamentally different morphologies. Here, the stability differences of surface sulphite at calcite CaCO 3 (s) and dolomite Ca x Mg 1-x CO 3 (s) are determined. A qualitative difference in surface sulphite stability, favouring the former, is reported. This is taken to imply that calcitic micro-crystals embedded in a dolomitic matrix act as sinks in the surface sulphation process, controlled by SO 2 diffusion. The subsequent formation of gypsum under such conditions will not require SO 4 2- (aq) ion transport. This explains the homogeneous distribution of gypsum observed on the calcitic micro-crystals in dolomite. In contrast, sulphation on purely calcitic marbles never reaches such high SO 2 coverage. Rather, upon oxidation, SO 4 2- (aq) transport to nucleation centres, such as grain boundaries, is required for the growth of gypsum crystals

A novel method of non-violent dissolution of sodium metal in a concentrated aqueous solution of Epsom salt

International Nuclear Information System (INIS)

Lakshmanan, A.R.; Prasad, M.V.R.; Ponraju, D.; Krishnan, H.

2004-01-01

A new technique of non-violent and fast dissolution of sodium metal in a concentrated aqueous solution of Epsom salt (MgSO 4 .7H 2 O) at room temperature (RT) has been developed. The dissolution process is mildly exothermic but could be carried out even in a glass beaker in air under swift stirring condition. The reaction products consist of mixed salts of MgSO 4 and Na 2 SO 4 as well as Mg(OH) 2 which are only mildly alkaline and hence are non-corrosive and non-hazardous unlike NaOH. A 50 mL solution having Epsom salt concentration of 2 M was found to give the optimal composition for disposal of 1 g of sodium. Supersaturated (>2.7 M), as well as dilute (<1.1 M) solutions, however, cause violent reactions and hence should be avoided. Repeated sodium dissolution in Epsom solution produced a solid waste of 4.7 g per g of sodium dissolved which is comparable with the waste (4 g) produced in 8 M NaOH solution. A 1.4 M Epsom solution sprayed with a high-pressure jet cleaner at RT in air easily removed the sodium blocked inside a metal pipe made of mild steel. The above jet also dissolved peacefully residual sodium collected on the metal tray after a sodium fire experiment. No sodium fire or explosion was observed during this campaign. The Epsom solution spray effectively neutralized the minor quantity of sodium aerosol produced during this campaign. This novel technique would hence be quite useful for draining sodium from fast breeder reactor components and bulk processing of sodium as well as for sodium fire fighting

Study of the solubility of yttrium, praseodymium, neodymium, and gadolinium sulfates in the presence of sodium and potassium in sulfuric-phosphoric acid solutions at 20 deg C

International Nuclear Information System (INIS)

Lokshin, Eh.P.; Tareeva, O.A.; Kashulina, T.G.

2007-01-01

The solubility of yttrium, praseodymium, neodymium, and gadolinium sulfates in the presence of sodium and potassium ions and the composition of solid phases were studied at 20 deg C in relation to the concentration of acids in sulfuric acid, phosphoric acid, and sulfuric-phosphoric acid solutions containing up to 36 wt % H 2 SO 4 and 33.12 g 1 -1 H 3 PO 4 . The formation of double sulfates of praseodymium and neodymium with sodium and potassium ions, as well as of gadolinium sulfate with sodium ions of the composition 1 : 1 was revealed. In water at 20 deg C, the solubility products of PrNa(SO 4 ) 2 ·H 2 O, NdNa(SO 4 ) 2 ·H 2 O, GdNa(SO 4 ) 2 ·H 2 O, PrK(SO 4 ) 2 ·H 2 O, and NdK(SO 4 ) 2 ·H 2 O are found to be 7.28x10 -8 , 7.84x10 -8 , 3.09x10 -6 , 3.02x10 -6 , and 1.70x10 -6 , respectively [ru

Ultra-low cost and highly stable hydrated FePO4 anodes for aqueous sodium-ion battery

Science.gov (United States)

Wang, Yuesheng; Feng, Zimin; Laul, Dharminder; Zhu, Wen; Provencher, Manon; Trudeau, Michel L.; Guerfi, Abdelbast; Zaghib, Karim

2018-01-01

The growing demands for large-scale energy storage devices have put a spotlight on aqueous sodium-ion batteries, which possess a number of highly desirable features, such as sodium abundance, low cost and safety over organic electrolytes. While lots of cathode materials were reported, only few candidate materials like active carbon and NaTi2(PO4)3 were proposed as anodes. It is a long-standing common knowledge that the low cost, non-toxicity, and highly reversible FePO4·2H2O is known as an attractive cathode material for non-aqueous lithium- and sodium-ion batteries, but we demonstrate for the first time that nano-size non-carbon coated amorphous FePO4·2H2O can be used as the anode for an aqueous sodium-ion battery. Its optimum operating voltage (∼2.75 V vs. Na+/Na) avoids hydrogen evolution. The capacity is as high as 80 mAh/g at a rate of 0.5 C in a three-electrode system. The full cell, using the Na0.44MnO2 as cathode, maintained 90% of the capacity at 300 cycles at a rate of 3 C. The calculations also show that its volume change during the intercalation of Na ions is below 2%. Its low cost, high safety, along with its outstanding electrochemical performance makes amorphous FePO4·2H2O a promising anode material for aqueous sodium-ion batteries.

To4, the first Tityus obscurus β-toxin fully electrophysiologically characterized on human sodium channel isoforms.

Science.gov (United States)

Duque, Harry Morales; Mourão, Caroline Barbosa Farias; Tibery, Diogo Vieira; Barbosa, Eder Alves; Campos, Leandro Ambrósio; Schwartz, Elisabeth Ferroni

2017-09-01

Many scorpion toxins that act on sodium channels (NaScTxs) have been characterized till date. These toxins may act modulating the inactivation or the activation of sodium channels and are named α- or β-types, respectively. Some venom toxins from Tityus obscurus (Buthidae), a scorpion widely distributed in the Brazilian Amazon, have been partially characterized in previous studies; however, little information about their electrophysiological role on sodium ion channels has been published. In the present study, we describe the purification, identification and electrophysiological characterization of a NaScTx, which was first described as Tc54 and further fully sequenced and renamed To4. This toxin shows a marked β-type effect on different sodium channel subtypes (hNa v 1.1-hNa v 1.7) at low concentrations, and has more pronounced activity on hNa v 1.1, hNa v 1.2 and hNa v 1.4. By comparing To4 primary structure with other Tityus β-toxins which have already been electrophysiologically tested, it is possible to establish some key amino acid residues for the sodium channel activity. Thus, To4 is the first toxin from T. obscurus fully electrophysiologically characterized on different human sodium channel isoforms. Copyright © 2017 Elsevier Inc. All rights reserved.

Study of mechanisms and kinetics of Sodium-CO2 interactions. Contribution to the evaluation of an energy conversion system with supercritical CO2 for sodium fast breeder reactors

International Nuclear Information System (INIS)

Gicquel, L.

2010-01-01

This PhD study consisted in studying reactive mechanisms and kinetics of sodium-CO 2 interactions, in the frame of the assessment of an energy conversion system with supercritical CO 2 for fast breeder reactors cooled by sodium. The approach was the following. First of all, the interactions between sodium and CO 2 have been brought to light by laboratory experiments associated with products analysis. They have enabled the establishment of a coherent mechanism, in agreement with literature data, and gave preliminary indications on the reaction kinetics. In order to estimate a more detailed reaction kinetics, we tried to approach the phenomenon that appears in the case of a leak in a sodium-CO 2 heat exchanger. Geometry of such heat exchangers is not fixed for the moment, even if the development of compact exchangers is foreseen. Then, free jets of CO 2 in liquid sodium have been modeled in order to obtain, by identification, kinetics parameters of the reaction. Those parameters, estimated with such a geometry, will remain valid with a much complex geometry, that will better represent the real exchanger. An experimental bench has been defined and built to realize those jets. The first laboratory experiments have concluded in the existence of different reactive mechanisms according to the temperature level. A threshold has been brought to light around 500 C. Below this one, reaction appears moderated, or even, slow, with a medium exothermicity, and appears after an induction period that depends on the temperature,and which duration could reach several hours. At contrary, above this threshold, it seems rapid and more exothermic. Below 500 C, sodium oxalate is produced, and then reacts with sodium in an exothermic way, following the reactions: CO 2 + Na →1/4 Na 2 C 2 O 4 + 1/4 CO + 1/4 Na 2 CO 3 (5) 4 Na + Na 2 C 2 O 4 → 3 Na 2 O + CO + C (6) Above 500 C, sodium carbonate is produced, and can then possibly react with sodium in an endothermic way, following the

High-Rate, Durable Sodium-Ion Battery Cathode Enabled by Carbon-Coated Micro-Sized Na ₃ V ₂ (PO ₄ ) ₃ Particles with Interconnected Vertical Nanowalls

Energy Technology Data Exchange (ETDEWEB)

Li, Hui [Beijing Key Laboratory of Environment Science and Engineering, School of Material Science and Engineering, Beijing Institute of Technology, Beijing 100081 China; Bi, Xuanxuan [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South, Cass Avenue Lemont IL 60439 USA; Bai, Ying [Beijing Key Laboratory of Environment Science and Engineering, School of Material Science and Engineering, Beijing Institute of Technology, Beijing 100081 China; Yuan, Yifei [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South, Cass Avenue Lemont IL 60439 USA; Department of Materials Science and Engineering, Michigan Technological University, 1400 Townsend Drive Houghton MI 49931 USA; Shahbazian-Yassar, Reza [Department of Materials Science and Engineering, Michigan Technological University, 1400 Townsend Drive Houghton MI 49931 USA; Wu, Chuan [Beijing Key Laboratory of Environment Science and Engineering, School of Material Science and Engineering, Beijing Institute of Technology, Beijing 100081 China; Collaborative Innovation Center of Electric Vehicles in Beijing, Beijing 100081 China; Wu, Feng [Beijing Key Laboratory of Environment Science and Engineering, School of Material Science and Engineering, Beijing Institute of Technology, Beijing 100081 China; Collaborative Innovation Center of Electric Vehicles in Beijing, Beijing 100081 China; Lu, Jun [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South, Cass Avenue Lemont IL 60439 USA; Amine, Khalil [Chemical Sciences and Engineering Division, Argonne National Laboratory, 9700 South, Cass Avenue Lemont IL 60439 USA

2016-02-08

Na-ion batteries have been regarded as promising alternatives for Li-ion batteries due to the extensive sodium reserves in the world. Na3V2(PO4)3 has been proved to be a good candidate of the cathode materials in Na-ion batteries but the intrinsic low electrical conductivity and sluggish kinetics handicapped its application. Here, 3D hierarchical Na3V2(PO4)3 particles are synthesized by a facile hydrothermal method, constructed by carbon-coated 2D Na3V2(PO4)3 nanowalls. Superior cell performance of high rate capability and cycle stability are observed in the well-defined structure. As the cathode in Na-ion batteries, it delivers a high capacity almost reaching the theoretical one and exhibits high capacity retention. The enhanced rate capability and cycle performance can be attributed to the improved electrical conductivity from the interconnected carbon layer and the shortened ion diffusion length and high specific surface area from the nanowalls.

NaGd(MoO4)2 nanocrystals with diverse morphologies: controlled synthesis, growth mechanism, photoluminescence and thermometric properties.

Science.gov (United States)

Li, Anming; Xu, Dekang; Lin, Hao; Yang, Shenghong; Shao, Yuanzhi; Zhang, Yueli

2016-08-10

Pure tetragonal phase, uniform and well-crystallized sodium gadolinium molybdate (NaGd(MoO4)2) nanocrystals with diverse morphologies, e.g. nanocylinders, nanocubes and square nanoplates have been selectively synthesized via oleic acid-mediated hydrothermal method. The phase, structure, morphology and composition of the as-synthesized products are studied. Contents of both sodium molybdate and oleic acid of the precursor solutions are found to affect the morphologies of the products significantly, and oleic acid plays a key role in the morphology-controlled synthesis of NaGd(MoO4)2 nanocrystals with diverse morphologies. Growth mechanism of NaGd(MoO4)2 nanocrystals is proposed based on time-dependent morphology evolution and X-ray diffraction analysis. Morphology-dependent down-shifting photoluminescence properties of NaGd(MoO4)2: Eu(3+) nanocrystals, and upconversion photoluminescence properties of NaGd(MoO4)2: Yb(3+)/Er(3+) and Yb(3+)/Tm(3+) nanoplates are investigated in detail. Charge transfer band in the down-shifting excitation spectra shows a slight blue-shift, and the luminescence intensities and lifetimes of Eu(3+) are decreased gradually with the morphology of the nanocrystals varying from nanocubes to thin square nanoplates. Upconversion energy transfer mechanisms of NaGd(MoO4)2: Yb(3+)/Er(3+), Yb(3+)/Tm(3+) nanoplates are proposed based on the energy level scheme and power dependence of upconversion emissions. Thermometric properties of NaGd(MoO4)2: Yb(3+)/Er(3+) nanoplates are investigated, and the maximum sensitivity is determined to be 0.01333 K(-1) at 285 K.

Nanowire Na0.35MnO2 from a hydrothermal method as a cathode material for aqueous asymmetric supercapacitors

Science.gov (United States)

Zhang, B. H.; Liu, Y.; Chang, Z.; Yang, Y. Q.; Wen, Z. B.; Wu, Y. P.; Holze, R.

2014-05-01

Nanowire Na0.35MnO2 was prepared by a simple and low energy consumption hydrothermal method; its electrochemical performance as a cathode material for aqueous asymmetric supercapacitors in Na2SO4 solution was investigated. Due to the nanowire structure its capacitance (157 F g-1) is much higher than that of the rod-like Na0.95MnO2 (92 F g-1) from solid phase reaction although its sodium content is lower. When it is assembled into an asymmetric aqueous supercapacitor using activated carbon as the counter electrode and aqueous 0.5 mol L-1 Na2SO4 electrolyte solution, the nanowire Na0.35MnO2 shows an energy density of 42.6 Wh kg-1 at a power density of 129.8 W kg-1 based on the total weight of the two electrode material, higher than those for the rod-like Na0.95MnO2, with an energy density of 27.3 Wh kg-1 at a power density of 74.8 W kg-1, and that of LiMn2O4. The new material presents excellent cycling behavior even when dissolved oxygen is not removed from the electrolyte solution. The results hold great promise for practical applications of this cathode material since sodium is much cheaper than lithium and its natural resources are rich.

Geochemical modelling of Na-SO4 type groundwater at Palmottu using a mass balance approach

International Nuclear Information System (INIS)

Pitkaenen, P.

1993-01-01

The mass balance chemical modelling technique has been applied to the groundwaters at the Palmottu analogue study site (in southwestern Finland) for radioactive waste disposal. The geochemical modelling concentrates on the evolution of Na-SO 4 type groundwater, which is spatially connected to the uranium mineralization. The results calculated along an assumed flow path are consistent with available field data and thermodynamic constraints. The results show that essential production of sulphides is unrealistic in the prevailing conditions. The increasing concentrations of Na, SO 4 and Cl along the evolution trend seem to have the same source and they could originate mainly from the leakage of fluid inclusions. Some mixing of relict sea water is also possible

Neutralization of Na2PO4: Reaction between Na3PO4 and CaCL2

International Nuclear Information System (INIS)

Xia Shenglan; Wang Luning

1990-01-01

The results of reaction Na 3 PO 4 with CaCl 2 in water at ambient and higher temperature are described. The reaction rate of Na 3 PO 4 with CaCl 2 is slow at ambient temperature and the reaction is complete at 260 deg C after 2 h. The products are Ca(OH) 2 and Ca 5 (PO 4 ) 3 (OH). The quantity of them is dependent upon the quanity of Na 3 PO 4 and CaCl 2 contained in water, all of them control pH of water

INVESTIGATION OF DISSOLVED SULPHATE IN VARIOUS GEOTHERMAL FIELDS OF SUMATRA USING OXYGEN AND SULPHUR ISOTOPES

Directory of Open Access Journals (Sweden)

E. Ristin Pujiindiyati

2010-06-01

Full Text Available There are at least 30 high temperature systems; eleven active volcanoes, five degassing volcanoes and one caldera volcano controlled by Sumatra Fault Zone over a length of 1700 km. To understand this geothermal field system, some information about geochemistry including isotope composition in its fluid is needed. Sulphur-34 and oxygen-18 isotopes in dissolved sulphate pair have been used to determine the origin of acidic fluid of sulphate and to evaluate the process involved. The fluids from eight hot springs, two fumaroles, four deep wells and crater have been collected in along Sumatra geothermal fields. Sulphur-34 (d 34S (SO4, 0/00 CDT and oxygen-18 (d 18O (SO4, 0/00 SMOW in sulphate is analyzed according to Robinson-Kusakabe and Rafter method, respectively. The d 34S (SO4 values from Sibayak wells are more enriched of 16.8 0/00 to 18.2 0/0 that may indicate the dissolution of anhydrite minerals or isotope partitioning in hydration of SO2. The d 34S (SO4 values from two fumaroles (Pusuk Bukit - North Sumatra and Rantau Dadap - South Sumatra are at depleted value of -0.150/00 and 1.80/00, those are close to d 34S from magmatic sulphur.  In general, the d 34S (SO4 of springs spread in a wide range of 5.250/00 to14.20/00 and show a mixing process between atmospheric sulphate and sulphate from deep wells. The d 18O (SO4 from wells exhibits depleted value around -3.60/00 suggesting that 87.5% of sulphate oxygen is derived from groundwater oxygen and 12.5% is derived from atmospheric molecular oxygen in sulphide oxidation reaction. In the other hand, hot springs (except Semurup, crater and fumaroles have enriched value of d 18O (SO4. These enriched values suggest that a higher percentage of atmospherically derived oxygen compared to those from the depth.   Keywords: isotope, geothermal, Sumatra