Temperature and sodium chloride effects on the solubility of anthracene in water

Energy Technology Data Exchange (ETDEWEB)

Arias-Gonzalez, Israel [Instituto Mexicano del Petroleo, Direccion de Investigacion y Posgrado, Programa de Ingenieria Molecular, Area de Investigacion en Termofisica, Eje Central Lazaro Cardenas Norte 152. 07730, Mexico D.F. (Mexico); Reza, Joel, E-mail: jreza@imp.m [Instituto Mexicano del Petroleo, Direccion de Investigacion y Posgrado, Programa de Ingenieria Molecular, Area de Investigacion en Termofisica, Eje Central Lazaro Cardenas Norte 152. 07730, Mexico D.F. (Mexico); Trejo, Arturo, E-mail: atrejo@imp.m [Instituto Mexicano del Petroleo, Direccion de Investigacion y Posgrado, Programa de Ingenieria Molecular, Area de Investigacion en Termofisica, Eje Central Lazaro Cardenas Norte 152. 07730, Mexico D.F. (Mexico)

2010-11-15

The solubility of anthracene was measured in pure water and in sodium chloride aqueous solution (salt concentration, m/mol . kg{sup -1} = 0.1006, 0.5056, and 0.6082) at temperatures between (278 and 333) K. Solubility of anthracene in pure water agrees fairly well with values reported in earlier similar studies. Solubility of anthracene in sodium chloride aqueous solutions ranged from (6 . 10{sup -8} to 143 . 10{sup -8}) mol . kg{sup -1}. Sodium chloride had a salting-out effect on the solubility of anthracene. The salting-out coefficients did not vary significantly with temperature over the range studied. The average salting-out coefficient for anthracene was 0.256 kg . mol{sup -1}. The standard molar Gibbs free energies, {Delta}{sub tr}G{sup o}, enthalpies, {Delta}{sub tr}H{sup o}, and entropies, {Delta}{sub tr}S{sup o}, for the transfer of anthracene from pure water to sodium chloride aqueous solutions were also estimated. Most of the estimated {Delta}{sub tr}G{sup o} values were positive [(20 to 1230) J . mol{sup -1}]. The analysis of the thermodynamic parameters shows that the transfer of anthracene from pure water to sodium chloride aqueous solution is thermodynamically unfavorable, and that this unfavorable condition is caused by a decrease in entropy.

Influence of sodium chloride on aflatoxin production by irradiated and non-irradiated spores of aspergillus flavus

International Nuclear Information System (INIS)

El-Bazza, Z.E.

1991-01-01

A liquid medium consisting of 2% yeast extract, 4% sucrose and 0-10% sodium chloride was inoculated with aspergillus flavus and incubated at 22.30 and 37 degree C for 8 days. Aflatoxin was determined in the medium by thin layer chromatography. Aflatoxin production was enhanced by 2 and 4% sodium chloride at 22 and 30 degree C and by 2-6% sodium chloride at 37 degree C. Aflatoxin was decreased by 8 and 10% sodium chloride at the three temperatures. Exposure of Asp. flavus spores to gamma radiation enhanced aflatoxin at 1 kGy and inhibited it at 2 kGy, with the different concentrations of sodium chloride.2 tab

Life cycle inventory of sodium acetate and expanded graphite: Short report

Energy Technology Data Exchange (ETDEWEB)

Jungbluth, N. [ESU-Services Ltd., Uster (Switzerland); Nguyen, B. [Haute Ecole d' Ingenierie et de Gestion du canton de Vaud, Laboratoire d' Energetique Solaire et de Physique du BATiment, HEIG-VD / LESBAT, Yverdon-les-Bains (Switzerland)

2008-07-01

This short report for the Laboratory for Solar Energy and Building Physics at the University of Applied Sciences in Yverdon, Switzerland, takes a look at work being done on the issue of solar energy storage. The use of sodium acetate as a phase-change material is reviewed and considered as being a good way of optimising solar heating systems. The goal of this study was to assess if the energy gain resulting from the use of sodium acetate is balanced out or not by its embodied energy. The study investigated sodium acetate with and without expanded graphite. The paper discusses the life cycle inventory analysis of the two materials and provides some aggregated key indicators for further analysis. In general the ecoinvent methodology has been followed in order to achieve full consistency with the background data used and to provide an assessment of the materials' impact on the environment.

Salt equivalence and temporal dominance of sensations of different sodium chloride substitutes in butter.

Science.gov (United States)

de Souza, Vanessa Rios; Freire, Tassyana Vieira Marques; Saraiva, Carla Gonçalves; de Deus Souza Carneiro, João; Pinheiro, Ana Carla Marques; Nunes, Cleiton Antônio

2013-08-01

Studies indicate a positive association between dietary salt intake and some diseases, which has promoted the tendency to reduce the sodium in foods. The objective of this study was to determine the equivalent amount of different sodium chloride replacements required to promote the same degree of ideal saltiness in butter and to study the sensory profile of sodium chloride and the substitutes using the analysis of Temporal Dominance of Sensations (TDS). Using the magnitude estimation method, it was determined that the potencies of potassium chloride, monosodium glutamate and potassium phosphate relative to the 1% sodium chloride in butter are 83·33, 31·59 and 33·32, respectively. Regarding the sensory profile of the tested salt substitutes, a bitter taste was perceived in the butter with potassium chloride, a sour taste was perceived in the butter with potassium phosphate and sweet and umami tastes were dominant in the butter with monosodium glutamate. Of all the salt substitutes tested calcium lactate, potassium lactate, calcium chloride and magnesium chloride were impractical to use in butter.

Activity of NaOH buffered by silicate solids in molten sodium acetate-water at 3170C

International Nuclear Information System (INIS)

Weres, O.; Tsao, L.

1988-01-01

Silica and sodium acetate are present in the steam generator tube sheet crevices of many nuclear power plants. Trace solutes in the condensate are tremendously concentrated in the crevices by boiling. Sparingly soluble sodium silicates and other solids precipitate from the crevice liquid leaving an extremely concentrated molten mixture of water, sodium acetate and other salts. The precipitates buffer the activity of sodium hydroxide in the superheated liquid that remains. The activity of NaOH corresponding to the buffers quartz/sodium disilicate and sodium disilicate/sodium metasilicate at 317 0 C has been determined experimentally. The sodium hydroxide content of a sodium acetate-water melt buffered by these reactions was determined by chemical analysis, and the corresponding activity of NaOH at temperature was calculated using the recently published Pitzer-Simonson Model of molten salt-water mixtures. The molten mixture of sodium acetate and water plays the role solvent in these experiments and calculations. The free energies of formation of solid sodium silicates at 317 0 C were also determined. The activity of NaOH corresponding to other silicate and phosphate buffers was calculated using published thermodynamic data and estimated from phase diagrams

Flame generation of sodium chloride aerosol for filter testing

International Nuclear Information System (INIS)

Edwards, J.; Kinnear, D.I.

1975-01-01

A generator for sodium chloride aerosol is described, which when used in conjunction with a sensitive portable sodium flame detector unit, will permit the in-place testing of large filter installations having air throughputs up to about 80,000 m 3 /h, at penetrations down to at least 0.005 percent. (U.S.)

Binary nucleation of water and sodium chloride

Czech Academy of Sciences Publication Activity Database

Němec, Tomáš; Maršík, František; Palmer, A.

2006-01-01

Roč. 124, č. 4 (2006), 0445091-0445096 ISSN 0021-9606 R&D Projects: GA ČR(CZ) GA101/05/2536 Institutional research plan: CEZ:AV0Z20760514 Keywords : binary nucleation * sodium chloride * water Subject RIV: BJ - Thermodynamics Impact factor: 3.166, year: 2006

Corrosion behavior of sodium-exposed stainless steels in chloride-containing aqueous solutions

International Nuclear Information System (INIS)

Wu, P.C.S.; Grundy, B.R.; Miller, R.L.

1979-01-01

The corrosion behavior of sodium-exposed stainless steels in chloride-containing aqueous solutions was investigated. Results showed that sodium-corroded Type 316 stainless steel (prototypic Liquid Metal Fast Breeder Reactor (LMFBR) fuel cladding) maintains its integrity after five months exposure in these solutions at 82 0 C and with chloride content up to 500 ppM. In contrast, sensitized and sodium mass transfer deposit-containing Type 304 stainless steel failed in the high chloride solution (500 ppM) within ten days at the same temperature. The failure was initiated by pitting and subsequently accelerated by intergranular attack. The results also show that high pH tends to reduce the susceptibility to failure while procedures commonly used for sodium removal have no significant effect on the water corrosion behavior of the test material. Based on the current results, it is concluded that water shortage is feasible for spent fuels in a LMFBR reprocessing plant

Long term thermal energy storage with stable supercooled sodium acetate trihydrate

DEFF Research Database (Denmark)

Dannemand, Mark; Schultz, Jørgen M.; Johansen, Jakob Berg

2015-01-01

Utilizing stable supercooling of sodium acetate trihydrate makes it possible to store thermal energy partly loss free. This principle makes seasonal heat storage in compact systems possible. To keep high and stable energy content and cycling stability phase separation of the storage material must...... it expands and will cause a pressure built up in a closed chamber which might compromise stability of the supercooling. This can be avoided by having an air volume above the phase change material connected to an external pressure less expansion tank. Supercooled sodium acetate trihydrate at 20 °C stores up...

Experimental investigations on heat content of supercooled sodium acetate trihydrate by a simple heat loss method

DEFF Research Database (Denmark)

Kong, Weiqiang; Dannemand, Mark; Johansen, Jakob Berg

2016-01-01

Sodium acetate trihydrate is a phase change material that can be used for long term heat storage in solar heating systems because of its relatively high heat of fusion, a melting temperature of 58 °C and its ability to supercool stable. In practical applications sodium acetate trihydrate tend to ......, 0.3–0.5 % (wt.%) Xanthan Gum or 1–2% (wt.%) of some solid or liquid polymers as additives had significantly higher heat contents compared to samples of sodium acetate trihydrate suffering from phase separation....

Development of seasonal heat storage based on stable supercooling of a sodium acetate water mixture

DEFF Research Database (Denmark)

Furbo, Simon; Fan, Jianhua; Andersen, Elsa

2012-01-01

A number of heat storage modules for seasonal heat storages based on stable supercooling of a sodium acetate water mixture have been tested by means of experiments in a heat storage test facility. The modules had different volumes and designs. Further, different methods were used to transfer heat...... to and from the sodium acetate water mixture in the modules. By means of the experiments: • The heat exchange capacity rates to and from the sodium acetate water mixture in the heat storage modules were determined for different volume flow rates. • The heat content of the heat storage modules were determined....... • The reliability of the supercooling was elucidated for the heat storage modules for different operation conditions. • The reliability of a cooling method used to start solidification of the supercooled sodium acetate water mixture was elucidated. The method is making use of boiling CO2 in a small tank in good...

The vapour pressures over saturated aqueous solutions of sodium and potassium acetates, chlorates, and perchlorates

Energy Technology Data Exchange (ETDEWEB)

Apelblat, Alexander [Department of Chemical Engineering, Ben Gurion University of the Negev, Beer Sheva 84105 (Israel)]. E-mail: apelblat@bgu.ac.il; Manzurola, Emanuel [Department of Chemical Engineering, Ben Gurion University of the Negev, Beer Sheva 84105 (Israel)

2007-08-15

Vapour pressures of water over saturated solutions of sodium acetate, potassium acetate, sodium perchlorate, and potassium perchlorate were determined over the (278 to 318) K temperature range and compared with available in the literature data. The cases of saturated solutions of sodium chlorate and potassium chlorate are also considered. The determined vapour pressures were used to obtain the water activities, the osmotic coefficients, and the molar enthalpies of vaporization in considered systems.

Effects of sodium chloride on radiation protection and modification of gamma-ray treated rice seeds

International Nuclear Information System (INIS)

Wang Cailian; Zhao Kongnan; Shen Mei; Xu Gang; Chen Qiufang

1992-11-01

The radiation protection effect of sodium chloride on dormant and germinating rice seeds treated with gamma-rays, and modification effect of sodium chloride on mutation were studied. Results show that the radiation-damage effect on seedling growth, percentage of seedling growth, percentage of seedling growth and fertility in M 1 generation is significantly enhanced with the increasing of dose. However, the seedling growth, percentage of seedling growth and fertility can be improved if the irradiated seeds are pre-treated with sodium chloride solution having concentrations of 0.05, 0.10 and 0.20 mol/L. The difference between treated group and control group is very significant. Results also show that pre-treatment and post-treatment by sodium chloride can raise the mutation frequencies of chlorophyll deficient seedlings, especially, the mutation frequency of early heading date and height is more considerably. The conclusion is that the sodium chloride, as a radiation protection agent, combined with gamma-ray treatment could reduce the effect of radiation-damage on M 1 generation and raise the mutation frequency in M 2 generation, and this result will be helpful in rice breeding

V color centers in electrolytically colored hydroxyl-doped sodium chloride crystals

International Nuclear Information System (INIS)

Gu Hongen; Song Cuiying; Han Li

2006-01-01

Hydroxyl-doped sodium chloride crystals were successfully colored electrolytically by using pointed anode and flat cathode at various temperatures and under various electric field strengths. V 2 and V 3 color centers were produced in the colored crystals. Current-time curves for the electrolytic colorations were given, and activation energy for the V 2 and V 3 color center migration was determined. Production of the V 2 and V 3 color centers and formation of current zones for the electrolytic colorations of the hydroxyl-doped sodium chloride crystals are explained

Amendment trials for bioremediation of sodium and chloride contaminated soils

Energy Technology Data Exchange (ETDEWEB)

Wilson, D. [Western Alfalfa Milling Co. Ltd., Norquay, SK (Canada)

2005-06-30

Details of a soil amendment experiment was presented. Soil samples from sodium and chloride contaminated soil were taken from a site located in southeastern Alberta. Soil amendments included high protein dehydrated alfalfa pellets, 2 types of Zeolite, and used coconut coir. The aim of the study was to find an effective in-situ method of remediating the soil while establishing the highest possible plant biomass. Preliminary trial data indicated a strong trend for high plant protein pellets to increase plant productivity on sodium and chloride contaminated soil. The addition of alfalfa increased plant height and stem diameter, as well as leaf width, which increased incrementally with higher volumes of alfalfa. Equivalent rates of .5 MT to 4 MT per acre application rates were used in the trial. Coconut coir was used at a rate of 30 per cent of the volume of the growing medium and also showed increased growth. An experiment was conducted using harvested plant matter from the samples to determine the effect of the 3 amendments on sodium uptake by the plants. Results showed that the sodium uptake significantly increased with the application of soil amendments, particularly when alfalfa pellets were applied, with percentages of sodium found in the plant tissue almost twice as high as percentages found in the control sample. Sodium levels also increased in the plant tissues where coconut coir was used, although to a lesser degree than levels found in plants grown with the alfalfa amended soils. Zeolite did not perform as well on its own. However, it was noted that previous trials have shown good performance when Zeolite was mixed into sodium/chloride contaminated soils and combined with water filtration. It was concluded that the soil amendments improved plant growth, and increased the sodium uptake by plants. The consortium is pursuing industry support to plan larger field studies in the 2006 season. 2 tabs., 5 figs.

Stability of penicillin G sodium diluted with 0.9% sodium chloride injection or 5% dextrose injection and stored in polyvinyl chloride bag containers and elastomeric pump containers.

Science.gov (United States)

Hossain, Mirza Akram; Friciu, Mihaela; Aubin, Sebastien; Leclair, Grégoire

2014-04-15

The stability of penicillin G sodium solutions stored in polyvinyl chloride (PVC) bags or elastomeric pump containers was studied. Test samples were prepared by diluting powdered penicillin G sodium (10 million units/10-mL vial) to solutions of 2,500 or 50,000 units/mL with 0.9% sodium chloride injection or 5% dextrose injection. The preparations were transferred to 250-mL PVC bags and elastomeric pump containers. All samples were prepared in triplicate and stored at 5°C. Chemical stability was measured by a stability-indicating high-performance liquid chromatographic (HPLC) assay and by pH evaluation. Particulate matter was evaluated according to compendial standards using a light-obscuration particle count test. Preparations were visually examined throughout the study. After 21 days of storage, all test samples remained chemically stable, with an HPLC assay recovery value of more than 90% of the initial value. After 28 days, all samples prepared with either diluent and stored in PVC bags, as well as the samples diluted to 2,500 units/mL with sodium chloride injection and stored in elastomeric pump containers, did not meet the recovery acceptance limit. For all test samples, the mean pH consistently decreased during storage, from about 6.4 to about 5.5. Particle counts remained acceptable throughout the study, and no change in appearance was observed. Penicillin G for injection (2,500 and 50,000 units/mL) diluted in 0.9% sodium chloride injection or 5% dextrose injection and stored at 5°C in PVC containers or elastomeric pump containers was physically and chemically stable for a period of at least 21 days.

Degradation of wall paints due to sodium sulphate and sodium chloride crystallization

Directory of Open Access Journals (Sweden)

Díaz Gonçalves, T.

2003-03-01

Full Text Available A test method for evaluating wall paints behaviour to soluble salts crystallization was developed at LNEC. in the present paper, a recent set of tests is described and discussed. The major objectives were: analysing and comparing the behaviour of a common emulsion {"plastic" paint and a silicate-based paint; observing and comparing the effect of sodium sulphate, sodium chloride and distilled water on the paints and on a non-painted stone; evaluating this test method adequacy and effectiveness. The silicate-based paint showed a resistance to soluble salts crystallization greater than the one of the plastic paint. However, the degradation pattern of the silicate-based paint (blistering of a filmic layer was similar to the one of organic paints and distinct from the one of pure mineral paints. The amount of damage that a saline solution can cause to wall paints cannot be inferred from the amount of damage it can cause to stone. Sodium chloride seems to be able to cause more severe degradation to wall paints than sodium sulphate. To the unpainted stone, sodium sulphate seems to be more damaging than sodium chloride. The test method seems adequate to observe and compare the behaviour of wall paints under soluble salts action. However, lower (around 0.5% concentrations for both sodium sulphate and sodium chloride should be tested in the future.

RESUMEN En el LNEC se desarrolló una metodología de ensayo para evaluar la respuesta de pinturas aplicadas sobre paredes, frente a la cristalización de sales solubles. En este trabajo, se describen y discuten un conjunto de ensayos recientes. Los principales objetivos fueron: el análisis y la comparación del comportamiento de una pintura de emulsión común {''pintura plástica" y la de una pintura de silicato; la observación y la comparación de los efectos del sulfato de sodio, del cloruro de sodio y del agua destilada sobre las pinturas y sobre piedra no pintada; la evaluación de la adecuaci

Liquid-liquid extraction of beryllium (II) using Cyanex 923 in kerosene from sodium acetate medium

International Nuclear Information System (INIS)

Kamble, Pravin N.; Madane, Namdev S.; Mohite, Baburao S.

2013-01-01

Liquid-liquid extraction of beryllium(II) from sodium acetate media using cyanex 923 in kerosene has been carried out. Beryllium(II) was quantitatively extracted from 1x10 -1 M sodium acetate with 1x10 -2 M cyanex 923 in kerosene. It was stripped quantitatively from the organic phase with 1M H 2 SO 4 and determined spectrophotometrically with eriochrome cyanine R at 525 nm. The effect of concentrations of sodium acetate, metal ions and strippants have been studied. Separation of beryllium(II) from other elements was achieved from binary as well as from multicomponent mixtures. The method is simple, rapid and selective with good reproducibility (approximately±2%). (author)

Meta-Analysis of Individual Patient Data of Sodium Bicarbonate and Sodium Chloride for All-Cause Mortality After Coronary Angiography

DEFF Research Database (Denmark)

Brown, Robert James (Jim); Pearlman, D. M.; Marshall, E. J.

2016-01-01

We sought to examine the relation between sodium bicarbonate prophylaxis for contrast associated nephropathy (CAN) and mortality. We conducted an individual patient data meta-analysis from multiple randomized controlled trials. We obtained individual patient data sets for 7 of 10 eligible trials (2......,292 of 2,764 participants). For the remaining 3 trials, time-to-event data were imputed based on follow-up periods described in their original reports. We included all trials that compared periprocedural intravenous sodium bicarbonate to periprocedural intravenous sodium chloride in patients undergoing...... bicarbonate was associated with lower mortality hazard than sodium chloride at 1 year (hazard ratio 0.61, 95% confidence interval [CI] 0.41 to 0.89, p = 0.011). Although periprocedural sodium bicarbonate was associated with a reduction in the incidence of CAN (relative risk 0.75, 95% CI 0.62 to 0.91, p = 0...

Long-term sodium chloride retention in a rural watershed: legacy effects of road salt on streamwater concentration.

Science.gov (United States)

Kelly, Victoria R; Lovett, Gary M; Weathers, Kathleen C; Findlay, Stuart E G; Strayer, David L; Burns, David I; Likens, Gene E

2008-01-15

Sodium and chloride concentrations and export increased from 1986 to 2005 in a rural stream in southeastern New York. Concentrations increased 1.5 mg/L per year (chloride) and 0.9 mg/L per year (sodium), and export increased 33,000 kg/year (chloride) and 20,000 kg/year (sodium) during this period. We estimate that salt used for deicing accounted for 91% of the sodium chloride input to the watershed, while sewage and water softeners accounted for less than 10% of the input. Road salt use in the watershed did not increase during the study, but sodium and chloride from sewage and water softeners is likely to have increased slightly due to a small increase in population. Increased input from sewage and water softeners cannot account for the increase in concentration and export from the watershed. Model results suggest that the increase in streamwater concentration and export was likely due to a lag effect of long-term road salt use and subsurface buildup.

Optical Detection of Sodium Salts of Fluoride, Acetate and ...

Indian Academy of Sciences (India)

Administrator

Optical Detection of Sodium Salts of Fluoride, Acetate and Phosphate by a Diacylhydrazine. Ligand via the Formation of a Colour Alkali Metal Complex. Purnandhu Bose, Ranjan Dutta, I. Ravikumar and Pradyut Ghosh. ∗. Department of Inorganic Chemistry, Indian Association for the Cultivation of Science, 2A & 2B Raja ...

Effect of Various Sodium Chloride Mass Fractions on Wheat and Rye Bread Using Different Dough Preparation Techniques

Directory of Open Access Journals (Sweden)

Małgorzata Tańska

2016-01-01

Full Text Available This study assessed the selected properties of bread with reduced amount of sodium chloride. The bread was made from white and wholemeal wheat flour and rye flour. The dough was prepared using three techniques: with yeast, natural sourdough or starter sourdough. Sodium chloride was added to the dough at 0, 0.5, 1.0 and 1.5 % of the flour mass. The following bread properties were examined in the study: yield and volume of the loaf, moisture content, crumb firmness and porosity, and organoleptic properties. Reducing the mass fraction of added sodium chloride was not found to have considerable effect on bread yield, whereas it had a significant and variable effect on the loaf volume, and crumb firmness and porosity. Organoleptic assessment showed diverse effects of sodium chloride addition on sensory properties of bread, depending on the type of bread and the dough preparation method. Reduced mass fractions of sodium chloride changed the organoleptic properties of bread made with yeast and with starter sourdough to a greater extent than of bread prepared with natural sourdough.

Effect of Various Sodium Chloride Mass Fractions on Wheat and Rye Bread Using Different Dough Preparation Techniques

Science.gov (United States)

Tańska, Małgorzata; Rotkiewicz, Daniela; Piętak, Andrzej

2016-01-01

Summary This study assessed the selected properties of bread with reduced amount of sodium chloride. The bread was made from white and wholemeal wheat flour and rye flour. The dough was prepared using three techniques: with yeast, natural sourdough or starter sourdough. Sodium chloride was added to the dough at 0, 0.5, 1.0 and 1.5% of the flour mass. The following bread properties were examined in the study: yield and volume of the loaf, moisture content, crumb firmness and porosity, and organoleptic properties. Reducing the mass fraction of added sodium chloride was not found to have considerable effect on bread yield, whereas it had a significant and variable effect on the loaf volume, and crumb firmness and porosity. Organoleptic assessment showed diverse effects of sodium chloride addition on sensory properties of bread, depending on the type of bread and the dough preparation method. Reduced mass fractions of sodium chloride changed the organoleptic properties of bread made with yeast and with starter sourdough to a greater extent than of bread prepared with natural sourdough. PMID:27904407

Effect of gamma radiation on glucose and sodium chloride solutions for injection

International Nuclear Information System (INIS)

Lakoza, G.N.; Grigor'eva, O.L.; Mart'yanova, B.M.; Vorob'eva, E.N.; Kuznetsova, R.M.

1976-01-01

Irradiation of 40% glucose solution with 0.5-4.0 Mrads di not affect the detoxicating properties of glucose or its ability to raise blood sugar levels. Such doses had no effect on the toxicological properties of 40% glucose solution and on 0.9% sodium chloride solution. The biological and physicochemical properties of 40% solution and 0.9% sodium chloride solutions irradiated with sterilizing doses showed no significant alterations during storage for one and three years, respectively. It is concluded that the solutions studied may be sterilized by radiation. (auth.)

Oxidation of sodium (2-14C) acetate with alkaline permanganate

International Nuclear Information System (INIS)

Zielinski, M.

1983-01-01

The mechanism and kinetics of the oxidation of sodium acetate with permanganate in alkile and neutral media have been investigated using (2- 14 C) acetate. The reaction is first order with respect to both permanganate and acetate ions. The initial second order rate constants depend linearly on the square of the hydroxide ion concentration. Arrhenius activation energy of the oxidation reaction carried out in 12M NaOH is 24.0 kcal/mole in the temperature interval of 50-100 deg C. The mechanism of the principal path leading to the oxalate formation and the mechanism of the side reaction resulting in the carbon dioxide production have been proposed and discussed. (author)

Determination of chloride and sulphur in sodium by ion chromatography and its application to PFBR sodium samples

International Nuclear Information System (INIS)

Vijayalakshmi, S.; Ushalakshmi, K.

2011-01-01

Analytical method using ion chromatography was developed for the determination of chloride and sulphur in sodium. In this method, sodium was dissolved in water and various sulphur species present in the sample was oxidized to sulphate using hydrogen peroxide. Carbon dioxide gas was passed through the solution to convert sodium hydroxide to carbonate solution. The resulting sample solution was analysed using suppressed Ion chromatography employing carbonate eluent. This method was applied to the analysis of sodium samples procured for prototype fast breeder reactor. (author)

Association between continuous peripheral i.v. infusion of 3% sodium chloride injection and phlebitis in adults.

Science.gov (United States)

Meng, Lina; Nguyen, Cherwyn M; Patel, Samit; Mlynash, Michael; Caulfield, Anna Finley

2018-03-01

One institution's experience with use of peripheral i.v. (PIV) catheters for prolonged infusions of 3% sodium chloride injection at rates up to 100 mL/hr is described. A prospective, observational, 13-month quality assurance project was conducted at an academic medical center to evaluate frequencies of patient and catheter phlebitis among adult inpatients who received both an infusion of 3% sodium chloride injection for a period of ≥4 hours through a dedicated PIV catheter and infusions of routine-care solutions (RCSs) through separate PIV catheters during the same hospital stay. Sixty patients received PIV infusions through a total of 291 catheters during the study period. The majority of patients (78%) received infusions of 3% sodium chloride injection for intracranial hypertension, with 30% receiving such infusions in the intensive care unit. Phlebitis occurred in 28 patients (47%) during infusions of 3% sodium chloride and 26 patients (43%) during RCS infusions ( p = 0.19). Catheter phlebitis occurred in 73 catheters (25%), with no significant difference in the frequencies of catheter phlebitis with infusion of 3% sodium chloride versus RCSs (30% [32 of 106 catheters]) versus 22% [41 of 185 catheters]), p = 0.16). Patient and catheter phlebitis rates were not significantly different with infusions of 3% sodium chloride injection versus RCSs, suggesting that an osmolarity cutoff value of 900 mOsm/L for peripheral infusions of hypertonic saline solutions may not be warranted. Copyright © 2018 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

Foliar application of ascorbic acid mitigates sodium chloride induced stress in eggplant (solanum melongena l.)

International Nuclear Information System (INIS)

Jan, S.; Hamayun, M.

2016-01-01

The current work was designed to test the effect of sodium chloride on germination, seedling establishment, vegetative growth, yield, chemical contents and ionic composition of eggplant. The consequences of foliar application of ascorbic acid (AA) on mitigation of adverse effects of sodium chloride were also tested. The seeds of Solanum melongena were germinated using NaCl (60 mM, 100 mM) and ascorbic acid (100 and 200 mM). High levels of salinity significantly affected the seed germination and seedling fresh and dry weights. Plants grown under salinity stress with foliar application of ascorbic acid showed significant increase in germination percentage and seedlings growth as compare to control plants. Sodium chloride stress showed adverse effects on plant height, root length, number of leaves, leaf area, fresh and dry biomass, total chlorophyll, carbohydrates and proteins as compared to untreated plants. The relative water content, electrolyte leakage were increased and Na+ and K+ ions balance was disturbed in different plant parts. Ascorbic acid (100 and 200ppm) enhanced all the growth parameters affected adversely by sodium chloride stress. (author)

Sodium Bicarbonate Versus Sodium Chloride for Preventing Contrast-Associated Acute Kidney Injury in Critically Ill Patients: A Randomized Controlled Trial.

Science.gov (United States)

Valette, Xavier; Desmeulles, Isabelle; Savary, Benoit; Masson, Romain; Seguin, Amélie; Sauneuf, Bertrand; Brunet, Jennifer; Verrier, Pierre; Pottier, Véronique; Orabona, Marie; Samba, Désiré; Viquesnel, Gérald; Lermuzeaux, Mathilde; Hazera, Pascal; Dutheil, Jean-Jacques; Hanouz, Jean-Luc; Parienti, Jean-Jacques; du Cheyron, Damien

2017-04-01

To test whether hydration with bicarbonate rather than isotonic sodium chloride reduces the risk of contrast-associated acute kidney injury in critically ill patients. Prospective, double-blind, multicenter, randomized controlled study. Three French ICUs. Critically ill patients with stable renal function (n = 307) who received intravascular contrast media. Hydration with 0.9% sodium chloride or 1.4% sodium bicarbonate administered with the same infusion protocol: 3 mL/kg during 1 hour before and 1 mL/kg/hr during 6 hours after contrast medium exposure. The primary endpoint was the development of contrast-associated acute kidney injury, as defined by the Acute Kidney Injury Network criteria, 72 hours after contrast exposure. Patients randomized to the bicarbonate group (n = 151) showed a higher urinary pH at the end of the infusion than patients randomized to the saline group (n = 156) (6.7 ± 2.1 vs 6.2 ± 1.8, respectively; p 0.99) were also similar between the saline and bicarbonate groups, respectively. Except for urinary pH, none of the outcomes differed between the two groups. Among ICU patients with stable renal function, the benefit of using sodium bicarbonate rather than isotonic sodium chloride for preventing contrast-associated acute kidney injury is marginal, if any.

Indium sulfide precipitation from hydrochloric acid solutions of calcium and sodium chlorides

International Nuclear Information System (INIS)

Kochetkova, N.V.; Bayandina, Yu.E.; Toptygina, G.M.; Shepot'ko, A.O.

1988-01-01

The effect of precipitation duration, acid concentration, indium complexing with chloride ions on the process of indium sulfide chemical precipitation in hydrochloric acid solutions, precipitate composition and dispersity are studied. It is established that indium sulfide solubility increases in solutions with acid concentration exceeding 0.40-0.45 mol/l. Calcium and indium chloride addition to diluted hydrochloric solutions greatly increases the solubility of indium sulfide. The effect of calcium chloride on In 2 S 3 solubility is higher than that of sodium chloride

Partial replacement of sodium chloride by potassium chloride in the formulation of French bread: effect on the physical, physicochemical and sensory parameters

Directory of Open Access Journals (Sweden)

Thaisa Abrantes Souza GUSMÃO

Full Text Available Abstract This study aimed to the replacement of sodium chloride (0.4 to 1.6% by potassium chloride (0.2 to 0.8% in French bread formulation and evaluate its effect on physical, physicochemical and sensory characteristics. For the preparation of bread was used a factorial design 22 with 4 factorial points and 3 central points, totaling 7 experiments. The physical and physicochemical parameters analyzed were: specific volume, moisture, color of the peel and crumb, pH, acidity and texture profile, sodium and potassium. The sensory evaluation of bread was performed using quantitative descriptive analysis, with 12 sensory terminologies. Response variables of salty taste and sensory chewiness generated statistically significant models. The results indicated optimal ranges of 0.2 to 0.5% of potassium chloride, and 1.0 to 1.6% for sodium chloride, and proved the technical feasibility of producing French bread with 50% salt reduction (174.09 mg.50 g–1, compared to a standard formulation of 1.88% (306.5 mg.50g-1 salt, corresponding to the prognosis recommended by the National Health Surveillance Agency.

Effects of topical flurbiprofen sodium, diclofenac sodium, ketorolac tromethamine and benzalkonium chloride on corneal sensitivity in normal dogs

Directory of Open Access Journals (Sweden)

Raquel de Araújo Cantarella

2017-08-01

Full Text Available To evaluate corneal sensitivity by using the Cochet-Bonnet® esthesiometer in normal canine eyes at different time points following instillation of three different topical non-steroidal anti-inflammatory drugs (flurbiprofen sodium 0.03%, diclofenac sodium 0.1% and ketorolac tromethamine 0.5% and benzalkonium chloride 0.01%. Six healthy mixed breed dogs from the same litter were used in two different stages. First, one drop of flurbiprofen sodium 0.03% and diclofenac sodium 0.1% in each eye; second, one drop of ketorolac tromethamine 0.5% and benzalkonium chloride 0.01% in each eye. Baseline esthesiometry was obtained before eye drop application and every 15 minutes thereafter until a total of 105 minutes of evaluation time. A one-week interval was allowed between the two treatment phases. Statistical analysis was used to compare means according to time of evaluation and drug used. Diclofenac sodium 0.1% decreased corneal sensitivity at 75 and 90 minutes (P > 0.015 with possible interference on neuronal nociceptive activity and analgesic effect while ketorolac tromethamine 0.5% did not show any variation for esthesiometry means along the evaluation. Flurbiprofen sodium 0.03% resulted in increased esthesiometry values 30 minutes after instillation (P > 0.013, increasing corneal sensitivity and possibly producing a greater irritant corneal effect over its analgesic properties. Benzalkonium chloride 0.01% significantly increased corneal sensitivity at 15 minutes of evaluation (P > 0.001, most likely resulting from its irritating effect. Esthesiometry did not allow a definite conclusion over the analgesic effect of the NSAIDs tested; however it was effective in detecting fluctuations in corneal sensitivity.

Stability of methadone hydrochloride in 0.9% sodium chloride injection in single-dose plastic containers.

Science.gov (United States)

Denson, D D; Crews, J C; Grummich, K W; Stirm, E J; Sue, C A

1991-03-01

The stability of methadone hydrochloride in 0.9% sodium chloride injection in flexible polyvinyl chloride containers was studied. Commercially available methadone hydrochloride 20 mg/mL and 25-mL single-dose bags of 0.9% sodium chloride injection were used. Six samples each were prepared at methadone hydrochloride concentrations of 1, 2, and 5 mg/mL. The solutions were stored at room temperature and were not protected from light. Immediately after preparation and after two, three, and four weeks of storage, each of the 18 samples was divided into three aliquots, each of which was analyzed in duplicate for methadone hydrochloride concentration by gas chromatography. There was less than 10% change in methadone hydrochloride concentration in any sample throughout the four-week study period. Methadone hydrochloride at concentrations of 1, 2, and 5 mg/mL prepared in commercially available flexible polyvinyl chloride containers of 0.9% sodium chloride injection and stored at room temperature without deliberate protection from light is stable for at least four weeks.

Respective effects of sodium and chloride ion on physiological ...

African Journals Online (AJOL)

Respective effects of sodium and chloride ion on growth, cell morphological changes, membrane disorganization, ion homeostasis, exoenzyme activities and fermentation performance in Zymomonas mobilis232B cultures were presented. In batch cultures containing 0.15 M NaCl, Z. mobilis232B developed filaments, and ...

Roentgen-phase analysis of sodium chloride of Khodja-Mumindeposit

International Nuclear Information System (INIS)

Nazarov, K.M.; Pulatov, M.S.; Isupov, S.D.

1999-01-01

With the purpose of determination of mineral composition of sodium chloride by authors was carried out the roentgen-phase analysis till its purification, after filtration and after purification from Ca 2 + , Mg 2 + a nd SO 4 2 + i ons by barium-carbonate and hydrochloride-acid methods

Scientific Opinion on the safety evaluation of the active substances, sodium carbonate peroxyhydrate coated with sodium carbonate and sodium silicate, bentonite, sodium chloride, sodium carbonate for use in active food contact materials

OpenAIRE

EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids (CEF)

2013-01-01

This scientific opinion of the Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids deals with the safety evaluation of the powder mixture of the active substances sodium carbonate peroxyhydrate coated with sodium carbonate and sodium silicate (FCM substance No 1009), bentonite (CAS No 1302-78-9, FCM No 393), sodium chloride (CAS No 7647-14-5, FCM No 985), sodium carbonate (CAS No 497-19-8, FCM No 1008) which are intended to be used as combined oxygen generator and carbon...

Sodium and chloride levels in rainfall, mist, streamwater and groundwater at the Plynlimon catchments, mid-Wales: inferences on hydrological and chemical controls

Directory of Open Access Journals (Sweden)

C. Neal

2000-01-01

Full Text Available Variations in sodium and chloride in atmospheric inputs (rainfall and mist, stream runoff and groundwater stores are documented for the upper Severn River (Afon Hafren and Afon Hore catchments, Plynlimon, mid-Wales. The results show five salient features. Sodium and chloride concentrations are highly variable and highly correlated in rainfall and mist. The sodium-chloride relationship in rainfall has a slope close to the sodium/chloride ratio in sea-water, and an intercept that is not significantly different from zero. This indicates that sea-salt is the dominant source of both sodium and chloride in rainfall, which would be expected given the maritime nature of the metrology. For mist, there is also a straight line with near-zero intercept, but with a slightly higher gradient than the sea-salt ratio, presumably due to small additional sodium inputs from other sources. There is an approximate input-output balance for both sodium and chloride, with the exception of one groundwater well, in which high chemical weathering results in an anomalous high Na/Cl ratio. Thus, atmospheric deposition is the dominant source of both sodium and chloride in groundwater and streamflow. The fluctuations in sodium and chloride concentrations in the streams and groundwaters are strongly damped compared to those in the rain and the mist, reflecting the storage and mixing of waters in the subsurface. On all timescales, from weeks to years, sodium fluctuations are more strongly damped than chloride fluctuations in streamflow. The additional damping of sodium is consistent with ion exchange buffering of sodium in the catchment soils.  Sodium and chloride concentrations are linearly correlated in the streams and groundwaters, but the slope is almost universally less than the sea-salt ratio and there is a non-zero intercept. The Na/Cl ratio in streamflow and groundwater is higher than the sea-salt ratio when salinity is low and lower than the sea-salt ratio when

Effects of salinity and ethylenediamine tetra acetic acid (edta) on the ...

African Journals Online (AJOL)

In this study, the effects of the combined treatment of salinity and ethylenediamine tetra acetic acid (EDTA) on the germination of tomato seeds in Petri-dishes were compared to sole salinity. The treatments consisted of seven concentrations of sodium chloride (NaCL): 0 (control), 10, 50, 100, 250, 500 and 1000 mM.

Comparative effects of Potash Sodium Chloride (PSC) mixture and ...

African Journals Online (AJOL)

Honey (Mellifica sp) is produced by Apis mellifera africana, widely consumed without prescription or restriction, and has been shown to possess wound healing and antitusive properties. Comparative study of the effects of honey paste and Potash Sodium Chloride (PSC) mixture on the healing of incisional wound on albino ...

Solidification behavior and thermal conductivity of bulk sodium acetate trihydrate composites with thickening agents and graphite

DEFF Research Database (Denmark)

Dannemand, Mark; Johansen, Jakob Berg; Furbo, Simon

2016-01-01

Sodium acetate trihydrate is a promising phase change material for long term storage of solar thermal energy if supercooling is actively utilized. Well performing thermal energy storages need to be able to charge and discharge energy at a high rate. The relatively low thermal conductivity....... Investigations of the solidification behavior, the formation of cavities and thermal conductivity of composites based on sodium acetate trihydrate crystalizing with or without supercooling are presented in this paper. The thermal conductivity was measured with an ISOMET hot disc surface measurement probe....... Samples that crystalized without supercooling tended to form solid crystals near the heat transfer surface and cavities away from the heat transfer surface. The measured thermal conductivity was up to 0.7 W/m K in solid sodium acetate trihydrate. Samples that crystalized from supercooled state formed...

Functional assessment of sodium chloride cotransporter NCC mutants in polarized mammalian epithelial cells

DEFF Research Database (Denmark)

Rosenbaek, Lena L; Rizzo, Federica; MacAulay, Nanna

2017-01-01

The thiazide-sensitive sodium chloride cotransporter NCC is important for maintaining serum sodium (Na(+)) and, indirectly, serum potassium (K(+)) levels. Functional studies on NCC have used cell lines with native NCC expression, transiently transfected nonpolarized cell lines, or Xenopus laevis...

MECHANICAL PROPERTIES OF BLENDS OF PAMAM DENDRIMERS WITH POLY(VINYL CHLORIDE) AND POLY(VINYL ACETATE)

Science.gov (United States)

Hybrid blends of poly(amidoamine) PAMAM dendrimers with two linear high polymers, poly(vinyl chloride), PVC, and poly(vinyl acetate), PVAc, are reported. The interaction between the blend components was studied using dynamic mechanical analysis, xenon nuclear magnetic resonacne ...

Stability of i.v. admixture containing metoclopramide, diphenhydramine hydrochloride, and dexamethasone sodium phosphate in 0.9% sodium chloride injection.

Science.gov (United States)

Kintzel, Polly E; Zhao, Ting; Wen, Bo; Sun, Duxin

2014-12-01

The chemical stability of a sterile admixture containing metoclopramide 1.6 mg/mL, diphenhydramine hydrochloride 2 mg/mL, and dexamethasone sodium phosphate 0.16 mg/mL in 0.9% sodium chloride injection was evaluated. Triplicate samples were prepared and stored at room temperature without light protection for a total of 48 hours. Aliquots from each sample were tested for chemical stability immediately after preparation and at 1, 4, 8, 24, and 48 hours using liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis. Metoclopramide, diphenhydramine hydrochloride, and dexamethasone sodium phosphate were selectively monitored using multiple-reaction monitoring. Samples were diluted differently for quantitation using three individual LC-MS/MS methods. To determine the drug concentration of the three compounds in the samples, three calibration curves were constructed by plotting the peak area or the peak area ratio versus the concentration of the calibration standards of each tested compound. Apixaban was used as an internal standard. Linearity of the calibration curve was evaluated by the correlation coefficient r(2). Constituents of the admixture of metoclopramide 1.6 mg/mL, diphenhydramine hydrochloride 2 mg/mL, and dexamethasone sodium phosphate 0.16 mg/mL in 0.9% sodium chloride injection retained more than 90% of their initial concentrations over 48 hours of storage at room temperature without protection from light. The observed variability in concentrations of these three compounds was within the limits of assay variability. An i.v. admixture containing metoclopramide 1.6 mg/mL, diphenhydramine hydrochloride 2 mg/mL, and dexamethasone sodium phosphate 0.16 mg/mL in 0.9% sodium chloride injection was chemically stable for 48 hours when stored at room temperature without light protection. Copyright © 2014 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

Rechargeable lithium and sodium anodes in chloroaluminate molten salts containing thionyl chloride

Energy Technology Data Exchange (ETDEWEB)

Fuller, J.; Osteryoung, R.A. [North Carolina State Univ., Raleigh, NC (United States). Dept. of Chemistry; Carlin, R.T.

1995-11-01

Lithium and sodium deposition-stripping studies were performed in room temperature buffered neutral chloroaluminate melts containing low concentrations of thionyl chloride (SOCl{sub 2}). The SOCl{sub 2} solute promotes high cycling efficiencies of the alkali metals in these electrolytes. Staircase cyclic voltammetry and chronopotentiometry show cycling efficiencies of approximately 90% for both lithium and sodium. High cycling efficiencies are maintained following extended exposure of the melt to the dry box atmosphere and after time delays at open circuit. The performance of the SOCl{sub 2}-promoted systems is substantially improved over previous studies in room temperature melts containing hydrogen chloride as the promoting solute.

Preservation of Steamed Fish (Rastrelliger Sp With Combine Method Using Sodium Acetate, Lactic Acid Bacteria Culture and Vacuum Packaging

Directory of Open Access Journals (Sweden)

Betty Sri Laksmi Jenie, . Nuratifa, . Suliantari

2001-04-01

Full Text Available This study was carried out to improve the safety and shelf life of cooked kembung fish (Rastrelliger sp, a traditional food called pindang fish. Fresh eviscerated fish was fisrt soaked in 2% NaCl solution for 15 minutes, drained, washed with tap water and drained again. Sodium chloride at 12% concentration (w/w was distributed on the whole surface of the fish. Fish was then laid on a wooden basket inside a clay pot, steamed for 30 minutes, and then cooled. Combine method applied to the steamed fish (pindang was soaking in a mixed culture of Lactobacillus plantarum kik and Lactococcus lactis subsp. cremoris in the ratio of 2 : 1 (v/v containing 4% Na-acetate for 2 hrs and after draining, the product was vacuum packed. The result showed that the combine method using mixed culture of lactic acid bacteria containing 4% Na-acetate could reduce the growth of Staphylococcus aureus by 3-6 log units, decrease the TMA (Trimethylamine content and maintain the organoleptic properties (texture, appearance and odor of pindang fish during 6 days storage at room temperature. Control treatment without 4% Na-acetate could only keep the pindang fish for 4 days. Vacuum and nonvacuum packaging did not show any significant difference.

Investigation into the role of sodium chloride deposited on oxide and metal substrates in the initiation of hot corrosion

Science.gov (United States)

Birks, N.

1983-01-01

Sodium chloride is deposited on the surface of alumina substrates and exposed to air containing 1% SO2 at temperatures between 500 C and 700 C. In all cases the sodium chloride was converted to sodium sulfate. The volatilization of sodium chloride from the original salt particles was responsible for the development of a uniform coating of sodium sulfate on the alumina substrate. At temperatures above 625 C, a liquid NaCl-Na2SO4 autectic was formed on the substrate. The mechanisms for these reactions are given. One of the main roles of NaCl in low temperature hot corrosion lies in enabling a corrosive liquid to form.

Sodium and chloride levels in rainfall, mist. streamwater and groundwater at the Plynlimon catchments, mid-Wales: inferences on hydrological and chemical controls

Science.gov (United States)

Neal, C.; Kirchner, J. W.

Variations in sodium and chloride in atmospheric inputs (rainfall and mist), stream runoff and groundwater stores are documented for the upper Severn River (Afon Hafren and Afon Hore catchments), Plynlimon, mid-Wales. The results show five salient features. Sodium and chloride concentrations are highly variable and highly correlated in rainfall and mist. The sodium-chloride relationship in rainfall has a slope close to the sodium/chloride ratio in sea-water, and an intercept that is not significantly different from zero. This indicates that sea-salt is the dominant source of both sodium and chloride in rainfall, which would be expected given the maritime nature of the metrology. For mist, there is also a straight line with near-zero intercept, but with a slightly higher gradient than the sea-salt ratio, presumably due to small additional sodium inputs from other sources. There is an approximate input-output balance for both sodium and chloride, with the exception of one groundwater well, in which high chemical weathering results in an anomalous high Na/Cl ratio. Thus, atmospheric deposition is the dominant source of both sodium and chloride in groundwater and streamflow. The fluctuations in sodium and chloride concentrations in the streams and groundwaters are strongly damped compared to those in the rain and the mist, reflecting the storage and mixing of waters in the subsurface. On all timescales, from weeks to years, sodium fluctuations are more strongly damped than chloride fluctuations in streamflow. The additional damping of sodium is consistent with ion exchange buffering of sodium in the catchment soils. Sodium and chloride concentrations are linearly correlated in the streams and groundwaters, but the slope is almost universally less than the sea-salt ratio and there is a non-zero intercept. The Na/Cl ratio in streamflow and groundwater is higher than the sea-salt ratio when salinity is low and lower than the sea-salt ratio when salinity is high. This

The Anion Paradox in Sodium Taste Reception: Resolution by Voltage-Clamp Studies

Science.gov (United States)

Ye, Qing; Heck, Gerard L.; Desimone, John A.

1991-11-01

Sodium salts are potent taste stimuli, but their effectiveness is markedly dependent on the anion, with chloride yielding the greatest response. The cellular mechanisms that mediate this phenomenon are not known. This "anion paradox" has been resolved by considering the field potential that is generated by restricted electrodiffusion of the anion through paracellular shunts between taste-bud cells. Neural responses to sodium chloride, sodium acetate, and sodium gluconate were studied while the field potential was voltage-clamped. Clamping at electronegative values eliminated the anion effect, whereas clamping at electropositive potentials exaggerated it. Thus, field potentials across the lingual epithelium modulate taste reception, indicating that the functional unit of taste reception includes the taste cell and its paracellular microenvironment.

Bacteria contributing to behaviour of radiocarbon in sodium acetate

International Nuclear Information System (INIS)

Ishii, N.; Uchida, S.

2011-01-01

An acetate-utilising bacterium was isolated and identified from deionised water that was used for flooding of paddy soils in this study's batch culture experiments. Bacteria in the deionised water samples formed colonies on agar plates containing [1,2- 14 C] sodium acetate, and the autoradiograms showed that all the colonies were positive for 14 C utilisation. Then one of the acetate-utilising bacteria was isolated. The isolate was characterised by phylogenetic analysis, cell morphology, Gram staining and growth at 30 deg. C. Phylogenetic analysis based on 16 S rRNA sequencing showed that the isolate belonged to the genus Burkholderia. The bacterium was gram-negative rods and grew at 30 deg. C under aerobic conditions. Based on these characteristics, the isolate was identified as Burkholderia gladioli. Because B. gladioli is often found in soil, water and the rhizosphere, attention must be paid to the relationships between bacteria and the behaviour of 14 C to for the safety assessment of geological disposal of transuranic waste. (authors)

Concentrations of chloride and sodium in groundwater in New Hampshire from 1960 through 2011

Science.gov (United States)

Medalie, Laura

2013-01-01

Several studies from the 1970s and more recently (for example, Hall (1975), Daley and others (2009) and Mullaney (2009)) have found that concentrations of chloride and sodium in groundwater in New Hampshire have increased during the past 50 years. Increases likely are related to road salt and other anthropogenic sources, such as septic systems, wastewater, and contamination from landfills and salt-storage areas. According to water-quality data reported to the New Hampshire Department of Environmental Services (NHDES), about 100 public water systems (5 percent) in 2010 had at least one groundwater sample with chloride concentrations that were equal to or exceeded the U.S. Environmental Protection Agency (USEPA) secondary maximum contaminant level (SMCL) of 250 mg/L before the water was treated for public consumption. The SMCL for chloride is a measurement of potential cosmetic or aesthetic effects of chloride in water. High concentrations of chloride and sodium in drinking-water sources can be costly to remove.

Optical detection of sodium salts of fluoride, acetate and phosphate

Indian Academy of Sciences (India)

Optical detection of sodium salts of fluoride, acetate and phosphate by a diacylhydrazine ligand by the formation of a colour alkali metal complex. Purnandhu Bose Ranjan Dutta I ... Department of Inorganic Chemistry, Indian Association for the Cultivation of Science, 2A and 2B Raja S C Mullick Road, Kolkata 700032, India ...

Zinc sacrificial anode behavior at elevated temperatures in sodium chloride and tap water environments

International Nuclear Information System (INIS)

Othman, Othman Mohsen

2005-01-01

Zinc sacrificial anode coupled to mild steel was tested in sodium chloride and tap water environments at elevated temperatures. The anode failed to protect the mild steel specimens in tap water environment at all temperatures specified for this study. This was partly due to the high resistivity of the medium. The temperature factor did not help to activate the anode in water tap medium. In sodium chloride environment the anode demonstrated good protection for steel cathodes. In tap water environment the anode weight loss was negligible. The zinc anode suffered intergranular corrosion in sodium chloride environment and this was noticed starting at 40 degree centigrade. In tap water environment the zinc anode demonstrated interesting behavior beyond 60 degree centigrade, that could be attributed to the phenomenon of reversal of potential at elevated temperatures. It also showed shallow pitting spots in tap water environment without any sign of intergranular corrosion. Zinc anodes would suffer intergranular corrosion at high temperatures. (author)

Progress and recent developments in sodium, metal chloride batteries

International Nuclear Information System (INIS)

Ratnakumar, B.V.; Attia, A.I.; Halpert, G.

1991-01-01

A new class of rechargeable sodium batteries emerged in the last decade mainly due to the efforts in South Africa and the United Kingdom. These systems include solid transition metal chlorides in sodium tetrachloroaluminates as cathodes. Significant developments have been made on two systems, i.e., Na/NiCl 2 and Na/FeCl 2 ; high energy densities of the order of 130 Wh/Kg have been demonstrated at the cell level both with FeCl 2 and NiCl 2 cathodes. Long cycle life of over 2000 cycles was demonstrated with NiCl 2 , especially with a sulfur additive to the electrolyte to retain the sintered structure of the NiCl 2 electrode. Various environmental and safety tests have been successfully performed on the cells. Scale up efforts resulted in cells of 40 - 100 Ah, which were evaluated in an electric vehicle application. Additionally, it appears from a recent evaluation study carried out by European Space Agency on Na/NiCl 2 for GEO and LEO applications that energy densities of the order of 120 Wh/Kg and 100 Wh/Kg respectively at the cell level are feasible and long cycle lives (beyond 2800 cycles are possible). Several fundamental and developmental studies have been carried out at other laboratories aimed at understanding the reaction mechanisms, determining the kinetics and identifying various rate governing processes, and screening various other metal chlorides. Finally, the specific energies and especially the power densities projected for Na/FeCl 2 and Na/NiCl 2 systems based on alternate designs for beta alumina solid electrolyte, i.e., multiple tubes and flat plates are very attractive for electric vehicle and space applications. In this paper, the authors propose to present a detailed account of the developments made hither to as well as the key research issues being addressed in the sodium - metal chloride battery technology

Sodium Chloride Dihydrate - A Potential Cause of Slippery Accidents

DEFF Research Database (Denmark)

Mejlholm, Morten; Thomsen, Kaj; Rasmussen, Peter

From a thermodynamic point of view, it can be expected that sodium chloride dihydrate (hydrohalite, NaCl2H2O) will form on winter roads under certain conditions at temperatures below 0.1¢®C. In order to elucidate whether or not the formation of hydrohalite on the pavement can explain the phenomenon...

Use of Hypertonic Sodium Chloride Solution at Surgery under Extracorporeal Circulation

Directory of Open Access Journals (Sweden)

V. V. Lomivorotov

2012-01-01

Full Text Available The paper analyzes the data available in the references on different aspects of using hypertonic sodium chloride solution during surgery under extracorporeal circulation in cardiosurgical care. The hypertonic solution is shown to lower positive fluid balance in the perioperative period, to increase cardiac output with simultaneously decreased vascular resistance, to improve lung oxygenating function, and to normalize tissue blood circulation and neurological status in patients exposed to artificial perfusion. There is evidence for its effect on the immune system and capillary endothelium. It is suggested that it is necessary to study the effect of the hypertonic solution on the incidence of complications and death rates during surgery under extracorporeal circulation and it is proposed to use the solution under long-term extracorporeal circulation. Key words: hypertonic saline, sodium chloride, extracorporeal circulation.

Increases in wintertime PM2.5 sodium and chloride linked to snowfall and road salt application

Science.gov (United States)

Kolesar, Katheryn R.; Mattson, Claire N.; Peterson, Peter K.; May, Nathaniel W.; Prendergast, Rashad K.; Pratt, Kerri A.

2018-03-01

The application of salts and salty brines to roads is common practice during the winter in many urban environments. Road salts can become aerosolized, thereby injecting sodium and chloride particulate matter (PM) into the atmosphere. Here, data from the United States Environmental Protection Agency Chemical Speciation Monitoring Network were used to assess temporal trends of sodium and chloride PM2.5 (PM road salt aerosols. Sodium and chloride PM2.5 concentrations were an average of three times higher in the winter, as compared to the summer, for locations with greater than 25 cm of average annual snowfall. Winter urban chloride PM2.5 concentrations attributed to road salt can even sometimes rival those of coastal sea spray aerosol-influenced sites. In most snow-influenced cities, chloride and sodium PM2.5 concentrations were positively correlated with snowfall; however, this relationship is complicated by differences in state and local winter maintenance practices. This study highlights the ubiquity of road salt aerosols in the United States and their potential impact on wintertime urban air quality, particularly due to the potential for multiphase reactions to liberate chlorine from the particle-phase. Since road salt application is a common practice in wintertime urban environments across the world, it is imperative that road salt application emissions, currently not included in inventories, and its impacts be investigated through measurements and modeling.

Effects of toxic levels of sodium, arsenic, iron and aluminum on the rice plant

Energy Technology Data Exchange (ETDEWEB)

Lockard, R G; McWalter, A R

1956-01-01

The results of two sand culture experiments on rice plants are described. In one, the toxic effects of sodium, as sodium chloride, and of arsenic, as sodium arsenate, were tested; in the other, iron, chelated with the disodium salt of ethylene-diamine-tetra-acetic acid, and aluminium, as aluminium sulfate, were tried out. The former was undertaken because of the existence of these sub

Micellar solubilization in strongly interacting binary surfactant systems. [Binary surfactant systems of: dodecyltrimethylammonium chloride + sodium dodecyl sulfate; benzyldimethyltetradecylammonium chloride + tetradecyltrimethylammonium chloride

Energy Technology Data Exchange (ETDEWEB)

Treiner, C. (Universite Pierre et Marie Curie, Paris (France)); Nortz, M.; Vaution, C. (Faculte de Pharmacie de Paris-sud, Chatenay-Malabry (France))

1990-07-01

The apparent partition coefficient P of barbituric acids between micelles and water has been determined in mixed binary surfactant solutions from solubility measurements in the whole micellar composition range. The binary systems chosen ranged from the strongly interacting system dodecyltrimethylammonium chloride + sodium dodecyl sulfate to weakly interacting systems such as benzyldimethyltetradecylammonium chloride + tetradecyltrimethyammonium chloride. In all cases studied, mixed micelle formation is unfavorable to micellar solubilization. A correlation is found between the unlike surfactants interaction energy, as measured by the regular solution parameter {beta} and the solute partition coefficient change upon surfactant mixing. By use of literature data on micellar solubilization in binary surfactant solutions, it is shown that the change of P for solutes which are solubilized by surface adsorption is generally governed by the sign and amplitude of the interaction parameter {beta}.

Kinetic Effect on the Freezing of Ammonium-Sodium-Carbonate-Chloride Brines and Implications for Origin of Ceres' Bright Spots

Science.gov (United States)

Hodyss, R. P.; Thomas, E. C.; Vu, T. H.; Johnson, P. V.; Choukroun, M.

2017-12-01

Subsurface brines on Ceres containing natrite (Na2CO3) and smaller amounts of NH4Cl or NH4HCO3 have been proposed to reach the dwarf planet's surface from an internal reservoir, where the brines freeze and result in bright spots across Ceres. Kinetically frozen solutions containing the likely constituents of Ceres' subsurface brines (ammonium, sodium, carbonate, and chloride ions) were studied via infrared and micro-Raman spectroscopy, where the flash-frozen mixtures were found to preferentially form ammonium chloride and ammonium bicarbonate, even in sodium-dominated solutions. Additionally, sodium chloride only formed when sodium or chloride (or both) were present in excess in the brine solutions. Raman spectroscopy was further employed to analyze the effect of vacuum exposure on these frozen brines over longer periods of time to simulate the surface conditions of Ceres.

Current Status of Health and Safety Issues of Sodium/Metal Chloride (Zebra) Batteries

International Nuclear Information System (INIS)

David Trickett

1998-01-01

This report addresses environmental, health, and safety (EH ampersand S) issues associated with sodium/ metal chloride batteries, in general, although most references to specific cell or battery types refer to units developed or being developed under the Zebra trademark. The report focuses on issues pertinent to sodium/metal chloride batteries and their constituent components; however, the fact that some ''issues'' arise from interaction between electric vehicle (EV) and battery design com- pels occasional discussion amid the context of EV vehicle design and operation. This approach has been chosen to provide a reasonably comprehensive account of the topic from a cell technology perspective and an applications perspective

Current Status of Health and Safety Issues of Sodium/Metal Chloride (Zebra) Batteries

Energy Technology Data Exchange (ETDEWEB)

Trickett, D.

1998-12-15

This report addresses environmental, health, and safety (EH&S) issues associated with sodium/ metal chloride batteries, in general, although most references to specific cell or battery types refer to units developed or being developed under the Zebra trademark. The report focuses on issues pertinent to sodium/metal chloride batteries and their constituent components; however, the fact that some ''issues'' arise from interaction between electric vehicle (EV) and battery design compels occasional discussion amid the context of EV vehicle design and operation. This approach has been chosen to provide a reasonably comprehensive account of the topic from a cell technology perspective and an applications perspective.

SODIUM-POTASSIUM-CHLORIDE COTRANSPORT IN THE REGULATION OF VASCULAR MYOGENIC TONE

Directory of Open Access Journals (Sweden)

S. N. Orlov

2014-01-01

Full Text Available The article discusses the data on the functioning of Na+,K+,2Cl– cotransport – the carrier providing electroneutral symport of sodium, potassium and chloride, as well as molecular mechanisms of the regulation and physiological significance of this carrier. We analyzed the novel data on involvement of ubiquitous isoform of Na+,K+,2Cl–cotransporter (NKCC1 in regulation of vascular smooth muscle contraction, and role of this carrier in the regulation of cell volume and intracellular chloride concentration.

Functional assessment of sodium chloride cotransporter NCC mutants in polarized mammalian epithelial cells.

Science.gov (United States)

Rosenbaek, Lena L; Rizzo, Federica; MacAulay, Nanna; Staub, Olivier; Fenton, Robert A

2017-08-01

The thiazide-sensitive sodium chloride cotransporter NCC is important for maintaining serum sodium (Na + ) and, indirectly, serum potassium (K + ) levels. Functional studies on NCC have used cell lines with native NCC expression, transiently transfected nonpolarized cell lines, or Xenopus laevis oocytes. Here, we developed the use of polarized Madin-Darby canine kidney type I (MDCKI) mammalian epithelial cell lines with tetracycline-inducible human NCC expression to study NCC activity and membrane abundance in the same system. In radiotracer assays, induced cells grown on filters had robust thiazide-sensitive and chloride dependent sodium-22 ( 22 Na) uptake from the apical side. To minimize cost and maximize throughput, assays were modified to use cells grown on plastic. On plastic, cells had similar thiazide-sensitive 22 Na uptakes that increased following preincubation of cells in chloride-free solutions. NCC was detected in the plasma membrane, and both membrane abundance and phosphorylation of NCC were increased by incubation in chloride-free solutions. Furthermore, in cells exposed for 15 min to low or high extracellular K + , the levels of phosphorylated NCC increased and decreased, respectively. To demonstrate that the system allows rapid and systematic assessment of mutated NCC, three phosphorylation sites in NCC were mutated, and NCC activity was examined. 22 Na fluxes in phosphorylation-deficient mutants were reduced to baseline levels, whereas phosphorylation-mimicking mutants were constitutively active, even without chloride-free stimulation. In conclusion, this system allows the activity, cellular localization, and abundance of wild-type or mutant NCC to be examined in the same polarized mammalian expression system in a rapid, easy, and low-cost fashion. Copyright © 2017 the American Physiological Society.

The influence of sodium salts (iodide, chloride and sulfate) on the formation efficiency of sulfamerazine nanocrystals.

Science.gov (United States)

Lou, Hao; Liu, Min; Qu, Wen; Johnson, James; Brunson, Ed; Almoazen, Hassan

2014-08-01

The purpose of this study is to evaluate the influence of sodium iodide, sodium chloride and sodium sulfate on the formation efficiency of sulfamerazine nanocrystals by wet ball milling. Sulfamerazine was milled using zirconium oxide beads in a solution containing polyvinylpyrrolidone (PVP) and a sodium salt (iodide, chloride or sulfate). Particle size distributions were evaluated by light diffraction before and after milling. High-performance liquid chromatography was utilized to determine the amount of PVP adsorbed onto sulfamerazine surface. Lyophilized nanocrystals were further characterized by differential scanning calorimetry and dissolution testing. Sulfate ion had more profound effect on reducing particle size via milling than iodide or chloride. We linked our findings to Hofmeister ion series, which indicates that sulfate ions tends to break the water structure, increases the surface tension and lowers the solubility of hydrocarbons in water. We hypothesized that the addition of sulfate ions dehydrated the PVP molecules and enhanced its adsorption onto the sulfamerazine particle surfaces. Consequently, the adsorbed PVP helped to stabilize of the nanosuspension. The nanocrystals that were obtained from the lyophilized milled suspensions exhibited a notable increase in dissolution rate. The addition of sodium sulfate enhanced the formation efficiency of sulfamerazine nanocrystals.

Ethanol-induced activation of adenine nucleotide turnover. Evidence for a role of acetate

International Nuclear Information System (INIS)

Puig, J.G.; Fox, I.H.

1984-01-01

Consumption of alcohol causes hyperuricemia by decreasing urate excretion and increasing its production. Our previous studies indicate that ethanol administration increases uric acid production by increasing ATP degradation to uric acid precursors. To test the hypothesis that ethanol-induced increased urate production results from acetate metabolism and enhanced adenosine triphosphate turnover, we gave intravenous sodium acetate, sodium chloride and ethanol (0.1 mmol/kg per min for 1 h) to five normal subjects. Acetate plasma levels increased from 0.04 +/- 0.01 mM (mean +/- SE) to peak values of 0.35 +/- 0.07 mM and to 0.08 +/- 0.01 mM during acetate and ethanol infusions, respectively. Urinary oxypurines increased to 223 +/- 13% and 316 +/- 44% of the base-line values during acetate and ethanol infusions, respectively. Urinary radioactivity from the adenine nucleotide pool labeled with [8-14C] adenine increased to 171 +/- 27% and to 128 +/- 8% of the base-line values after acetate and ethanol infusions. These data indicate that both ethanol and acetate increase purine nucleotide degradation by enhancing the turnover of the adenine nucleotide pool. They support the hypothesis that acetate metabolism contributes to the increased production of urate associated with ethanol intake

Impact of sodium chloride on breakfast cereal products

OpenAIRE

Moreau, Lydie

2009-01-01

To reduce the amount of sodium chloride in breakfast cereals without changing their properties, it is necessary to understand the role of this salt. Hence, a model system was developed. This model, composed of native waxy maize starch, glucose and a mixture of amino-acids generated similar colour and residual volatiles after heating compared to commercial breakfast cereals. Systematically designed experiments used this model to study the influence of NaCl concentration (0 % to 5.44 %) on colo...

Use of potassium chloride and flavor enhancers in low sodium Cheddar cheese.

Science.gov (United States)

Grummer, J; Bobowski, N; Karalus, M; Vickers, Z; Schoenfuss, T

2013-03-01

We investigated use of potassium chloride (KCl) to maintain both the salty flavor and to replace the preservative effects of salt when reducing the sodium content in natural cheese. Because salt replacers can affect flavor because of inherent off-flavors, such as bitter and metallic, we examined the use of flavor enhancers for their ability to modulate some of these undesirable sensory effects. Stirred-curd Cheddar-style cheese was manufactured using 2 cheese-making procedures (different curd knife sizes and target salting titratable acidities), in duplicate. Curd was salted with sodium chloride (NaCl) or 60% reduced sodium blends of NaCl and KCl (2 different sources). Curd was also salted at a 60% reduced sodium rate with NaCl and KCl with added flavor enhancers. A hydrolyzed vegetable protein/yeast extract blend, a natural "potassium-blocking type" flavor, disodium inosinate, or disodium guanylate were each blended with the reduced sodium salt blend and added to curd at the salting step. The resulting blocks of cheese were aged for 5 mo and evaluated monthly for chemical, microbial, and sensory differences. At 5 mo of aging, we measured liking for the cheeses using a consumer panel. Overall, cheeses were well liked by the consumer panel, and the scores of reduced sodium cheese with 2 different KCl sources were not different from those of the full-sodium control. The addition of flavor enhancers to Cheddar curd had mixed results, with one improving the consumer flavor liking only slightly over KCl, and one (disodium inosinate) significantly reducing consumer flavor liking scores, presumably due to the amount of umami flavor it contributed. Potassium chloride replacement salts sourced from different manufacturers affected the chemical and flavor properties of cheese, and changes to pH and temperature targets may be necessary to yield cheese with the moisture and pH targets desired. The cheese-making procedure used also influenced flavors observed, which resulted in

Effect of radioactive chromate on the corrosion and polarisation of mild steel in sodium chloride solution

International Nuclear Information System (INIS)

Subramanyan, N.; Ramakrishnaiah, K.; Iyer, S.V.; Kapali, V.

1980-01-01

Corrosion tests of mild steel in 0.01% sodium chloride containing radioactive chromate and non-radioactive chromate have been carried out. It has been observed that the labelled sodium chromate has a deleterious effect on the inhibitive action of non-radioactive chromate. The effect of radioactive chromate on the potentiostatic polarization of m.s. in sodium chloride solution containing non-radioactive sodium chromate has also been studied. It is observed that both the cathodic and the anodic polarisation of the metal is diminished in the presence of radioactive chromate. The behaviour of the system in the presence of radioactive chromate is attributed both to the action of depolarisers produced by radiolysis of water and to the effect of gamma radiation on the metal. (author)

Substituted sodium phenylanthranylates as inhibitors of corrosion in chloride solutions

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, Yu.I.; Fialkov, Yu.A.; Popova, L.I.; Ehndel' man, E.S.; Kuznetsova, I.G. (AN SSSR, Moscow. Inst. Fizicheskoj Khimii)

The efficiency of corrosion protection of armco iron, zinc (Ts-O) aluminium (AB 000) and its alloys (.D16 and AMG6) with sodium phenylanthranylate derivatives in chloride buffer solutions (pH 7.4-8.08) are investigated. It has been ascertained that the introduction of sodium phenylanthranylate into phenyl radical in m- and p-position relative to the amino group of electron-seeking substitutes improves protective properties of an inhibitor. The inhibiting effect of phenylanthranylates and its dependence on electron structure enchances in zinc-aluminium-iron series and decreases in case of transition from pure aluminium to its alloys.

Extended stability of intravenous 0.9% sodium chloride solution after prolonged heating or cooling.

Science.gov (United States)

Puertos, Enrique

2014-03-01

The primary objective of this study was to evaluate the stability and sterility of an intravenous 0.9% sodium chloride solution that had been cooled or heated for an extended period of time. Fifteen sterile 1 L bags of 0.9% sodium chloride solution were randomly selected for this experiment. Five bags were refrigerated at an average temperature of 5.2°C, 5 bags were heated at an average temperature of 39.2°C, and 5 bags were stored at an average room temperature of 21.8°C to serve as controls. All samples were protected from light and stored for a period of 199 days prior to being assayed and analyzed for microbial and fungal growth. There was no clinically significant difference in the mean sodium values between the refrigerated samples, the heated samples, and the control group. There were no signs of microbial or fungal growth for the duration of the study. A sterile intravenous solution of 0.9% sodium chloride that was heated or cooled remained stable and showed no signs of microbial or fungal growth for a period of 199 days. This finding will allow hospitals and emergency medical technicians to significantly extend the expiration date assigned to these fluids and therefore obviate the need to change out these fluids every 28 days as recommended by the manufacturer.

The use of sodium alginate-based coating and cellulose acetate in papaya post-harvest preservation

Directory of Open Access Journals (Sweden)

Denise Andrade Silva

2014-02-01

Full Text Available This study aimed to evaluate the ripening of papaya fruit (Carica papaya L. at room temperature (±25°C and10°C with 80% relative humidity, coated with edible film based on sodium alginate (1% and cellulose acetate film (3% by dipping the fruit in the suspensions for 1 min. On the application of the treatment and every three days during 12 days of storage, fruit were evaluated for weight loss, firmness, total carotenoid content, lycopene content and vitamin C content of the pulp. The cellulose acetate film extended the shelf-life of papayas, without affecting their quality. This treatment delayed fruit ripening, whose changes in all the parameters analyzed were significantly slower than fruit treated with sodium alginate-based coating. The coating with cellulose acetate at 3% was more effective in the preservation of papaya stored for 12 days under both temperatures.

The determination of hydroxide and carbonate in concentrated sodium chloride solutions

NARCIS (Netherlands)

Roolvink, W.B.; Bos, M.

1980-01-01

A computer method for the determination of carbonate and hydroxide in concentrated (2.89 M) sodium chloride solutions is described. The method is based on multiparametric curve-fitting and can also be applied to salts of dibasic acids with unknown equilibrium constants. The systematic error is not

Sodium, potassium and chloride status in Australian foods and diets using neutron activation analysis

Energy Technology Data Exchange (ETDEWEB)

Fardy, J J; McOrist, G D; Farrar, Y J; Bowles, C J [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia)

1994-12-31

A study of the status of essential, toxic and trace elements in the foods and diets of Australian has been in progress for six years. Results for sodium, potassium and chloride levels are reported here. The average daily dietary intake of sodium and chloride exceeded the range of values recommended by the National Health and Medical Research Council for most population groups with grain and dairy products the main contributor to these high intakes. In contrast, the average daily intakes of potassium fell well within the recommended values for all age groups with intakes for adult females close to the recommended minimum figure. 9 refs., 1 tab., 2 figs.

Sodium, potassium and chloride status in Australian foods and diets using neutron activation analysis

Energy Technology Data Exchange (ETDEWEB)

Fardy, J.J.; McOrist, G.D.; Farrar, Y.J.; Bowles, C.J. [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia)

1993-12-31

A study of the status of essential, toxic and trace elements in the foods and diets of Australian has been in progress for six years. Results for sodium, potassium and chloride levels are reported here. The average daily dietary intake of sodium and chloride exceeded the range of values recommended by the National Health and Medical Research Council for most population groups with grain and dairy products the main contributor to these high intakes. In contrast, the average daily intakes of potassium fell well within the recommended values for all age groups with intakes for adult females close to the recommended minimum figure. 9 refs., 1 tab., 2 figs.

Standard test method for evaluating stress-corrosion cracking of stainless alloys with different nickel content in boiling acidified sodium chloride solution

CERN Document Server

American Society for Testing and Materials. Philadelphia

2000-01-01

1.1 This test method describes a procedure for conducting stress-corrosion cracking tests in an acidified boiling sodium chloride solution. This test method is performed in 25% (by mass ) sodium chloride acidified to pH 1.5 with phosphoric acid. This test method is concerned primarily with the test solution and glassware, although a specific style of U-bend test specimen is suggested. 1.2 This test method is designed to provide better correlation with chemical process industry experience for stainless steels than the more severe boiling magnesium chloride test of Practice G36. Some stainless steels which have provided satisfactory service in many environments readily crack in Practice G36, but have not cracked during interlaboratory testing using this sodium chloride test method. 1.3 This boiling sodium chloride test method was used in an interlaboratory test program to evaluate wrought stainless steels, including duplex (ferrite-austenite) stainless and an alloy with up to about 33% nickel. It may also b...

Porosity and density measurements of sodium acetate trihydrate for thermal energy storage

DEFF Research Database (Denmark)

Dannemand, Mark; Delgado, Monica; Lazaro, Ana

2018-01-01

Sodium acetate trihydrate (SAT) can be used as phase change material in latent heat storage with or without utilizing supercooling. The change of density between liquid to solid state leads to formation of cavities inside the bulk SAT during solidification. Samples of SAT which had solidified from...

Safety assessment of sodium acetate, sodium diacetate and potassium sorbate food additives.

Science.gov (United States)

Mohammadzadeh-Aghdash, Hossein; Sohrabi, Yousef; Mohammadi, Ali; Shanehbandi, Dariush; Dehghan, Parvin; Ezzati Nazhad Dolatabadi, Jafar

2018-08-15

Cytotoxicity and genotoxicity of sodium acetate (SA), sodium diacetate (SDA), and potassium sorbate (PS) was tested on Human Umbilical Vein Endothelial Cells (HUVEC). Cytotoxicity was investigated by MTT assay and flow cytometry analysis, while genotoxicity was evaluated using DNA fragmentation and DAPI staining assays. The growth of treated HUVECs with various concentrations of SA, SDA and PS decreased in a dose-and time-dependent manner. The IC50 of 487.71, 485.82 and 659.96 µM after 24 h and IC50 of 232.05, 190.19 and 123.95 µM after 48 h of treatment were attained for SA, SDA and PS, respectively. Flow cytometry analysis showed that early and late apoptosis percentage in treated cells was not considerable. Also neither considerable DNA fragmentation nor DNA smear was observed using DAPI staining and DNA ladder assays. Overall, it can be concluded that the aforementioned food additives can be used as safe additives at low concentration in food industry. Copyright © 2018 Elsevier Ltd. All rights reserved.

Characterization of a novel phosphorylation site in the sodium-chloride cotransporter, NCC

DEFF Research Database (Denmark)

Rosenbaek, L L; Assentoft, M; Pedersen, N B

2012-01-01

The sodium-chloride cotransporter, NCC, is essential for renal electrolyte balance. NCC function can be modulated by protein phosphorylation. In this study, we characterized the role and physiological regulation of a novel phosphorylation site in NCC at Ser124 (S124). Novel phospho-specific antib......The sodium-chloride cotransporter, NCC, is essential for renal electrolyte balance. NCC function can be modulated by protein phosphorylation. In this study, we characterized the role and physiological regulation of a novel phosphorylation site in NCC at Ser124 (S124). Novel phospho......-related proline-alanine-rich kinase and oxidative stress-response kinases (SPAK and OSR1) were not able to phosphorylate NCC at S124. Protein kinase arrays identified multiple kinases that were able to bind to the region surrounding S124. Four of these kinases (IRAK2, CDK6/Cyclin D1, NLK and m...

Aqueous protocol for allylic arylation of cinnamyl acetates with sodium tetraphenylborate using Bedford-type palladacycle catalyst

KAUST Repository

Ghorpade, Seema Arun; Sawant, Dinesh N; Renn, Dominik; Zernickel, Anna; Du, Weiyuan; Sekar, Nethi; Eppinger, Jö rg

2018-01-01

Allylic arylation of cinnamyl acetates with sodium tetraphenylborate using 0.002 mol % of Bedford-type palladacycle catalyst is described. The developed methodology is applicable for wide range of cinnamyl acetates furnishing excellent yields up to 93%. Notably all reactions proceed smoothly under mild reaction conditions in water under air atmosphere.

Aqueous protocol for allylic arylation of cinnamyl acetates with sodium tetraphenylborate using Bedford-type palladacycle catalyst

KAUST Repository

Ghorpade, Seema Arun

2018-03-19

Allylic arylation of cinnamyl acetates with sodium tetraphenylborate using 0.002 mol % of Bedford-type palladacycle catalyst is described. The developed methodology is applicable for wide range of cinnamyl acetates furnishing excellent yields up to 93%. Notably all reactions proceed smoothly under mild reaction conditions in water under air atmosphere.

Influence of sodium chloride on wine yeast fermentation performance

Directory of Open Access Journals (Sweden)

Stilianos Logothetis

2010-06-01

Full Text Available Stilianos Logothetis1, Elias T Nerantzis2, Anna Gioulioti3, Tasos Kanelis2, Tataridis Panagiotis2, Graeme Walker11University of Abertay Dundee, School of Contemporary Sciences, Dundee, Scotland; 2TEI of Athens Department of Oenology and Spirit Technology, Biotechnology and Industrial Fermentations Lab Agiou Spiridonos, Athens, Greece; 3Ampeloiniki SA Industrial Park Thermi, Thessaloniki, GreeceAbstract: This paper concerns research into the influence of salt (sodium chloride on growth, viability and fermentation performance in a winemaking strain of the yeast, Saccharomyces cerevisiae. Experimental fermentations were conducted in both laboratory-scale and industrial-scale experiments. Preculturing yeasts in elevated levels of sodium chloride, or salt “preconditioning” led to improved fermentation performance. This was manifest by preconditioned yeasts having an improved capability to ferment high-sugar containing media with increased cell viability and with elevated levels of produced ethanol. Salt-preconditioning most likely influenced the stress-tolerance of yeasts by inducing the synthesis of key metabolites such as trehalose and glycerol. These compounds may act to improve cells’ ability to withstand osmostress and ethanol toxicity during fermentations of grape must. Industrial-scale trials using salt-preconditioned yeasts verified the benefit of this novel physiological cell engineering approach to practical winemaking fermentations.Keywords: salt, preconditioning, fermentation performance, Saccharomyces cerevisiae, wine

Hazard identification for human and ecological effects of sodium chloride road salt.

Science.gov (United States)

2007-07-01

The New Hampshire Department of Environmental Services (DES) requested an evaluation of : the human and ecological risks associated with the application of sodium chloride (NaCl) road : salt to roadways. NaCl is the major de-icing agent used in NH to...

Compatibility of butorphanol and droperidol in 0.9% sodium chloride injection.

Science.gov (United States)

Chen, Fu-Chao; Fang, Bao-Xia; Li, Peng; Yang, Jin-Guo; Zhou, Ben-Hong

2013-03-15

The compatibility and stability of butorphanol tartrate and droperidol in polyvinyl chloride (PVC) bags and glass bottles stored at 4°C and 25°C for up to 15 days were studied. Admixtures were assessed initially and for 15 days after preparation in PVC bags and glass bottles using 0.9% sodium chloride injection as a diluent and stored at 4°C and 25°C. The initial drug concentrations were 0.08 mg/mL for butorphanol tartrate and 0.05 mg/mL for droperidol. Samples were withdrawn from each container immediately after preparation and at predetermined intervals (2, 4, 8, 24, 48, 72, 120, 168, 240, and 360 hours after preparation). The solutions were visually inspected for precipitation, cloudiness, and discoloration at each sampling interval. Drug concentrations were determined using a validated high-pressure liquid chromatography method. After 15 days of storage, all formulations tested retained >98% of the initial concentrations of both drugs. The drug mixtures were clear in appearance, and no color change or precipitation was observed. Throughout this period, pH values remained stable. Admixtures of butorphanol tartrate 0.08 mg/mL and droperidol 0.05 mg/mL in 0.9% sodium chloride injection were stable for at least 360 hours when stored in PVC bags or glass bottles at 4°C and 25°C and protected from light.

Sodium Is Not Required for Chloride Efflux via Chloride/Bicarbonate Exchanger from Rat Thymic Lymphocytes

Directory of Open Access Journals (Sweden)

Donatas Stakišaitis

2014-01-01

Full Text Available Sodium-dependent Cl−/HCO3- exchanger acts as a chloride (Cl− efflux in lymphocytes. Its functional characterization had been described when Cl− efflux was measured upon substituting extracellular sodium (Na+ by N-methyl-D-glucamine (NMDG. For Na+ and Cl− substitution, we have used D-mannitol or NMDG. Thymocytes of male Wistar rats aged 7–9 weeks were used and intracellular Cl− was measured by spectrofluorimetry using MQAE dye in bicarbonate buffers. Chloride efflux was measured in a Cl−-free buffer (Cl− substituted with isethionate acid and in Na+ and Cl−-free buffer with D-mannitol or with NMDG. The data have shown that Cl− efflux is mediated in the absence of Na+ in a solution containing D-mannitol and is inhibited by H2DIDS. Mathematical modelling has shown that Cl− efflux mathematical model parameters (relative membrane permeability, relative rate of exchanger transition, and exchanger efficacy were the same in control and in the medium in which Na+ had been substituted by D-mannitol. The net Cl− efflux was completely blocked in the NMDG buffer. The same blockage of Cl− efflux was caused by H2DIDS. The study results allow concluding that Na+ is not required for Cl− efflux via Cl−/HCO3- exchanger. NMDG in buffers cannot be used for substituting Na+ because NMDG inhibits the exchanger.

The study of interaction of lanthanum-, cerium- and neodymium chlorides with sodium borohydride in pyridine- and tetrahydrofuran medium

International Nuclear Information System (INIS)

Mirsaidov, U.; Rotenberg, T.G.; Dymova, T.N.

1976-01-01

Bis-tetrahydrofurans of lanthanum and neodymium borohydrides and bis-pyridinates of lanthanum, cerium and neodymium borohydrides were obtained by interacting sodium borohydride with lanthanum-, cerium and neodymium chlorides in pyridine and tetrahydrofuran media. All operations involving reagent combination, sampling and phase separation are performed in inert atmosphere using argonvacuum equipment. The reaction in pyridine was virtually instantaneous and accompanied by flocculanet precipitation. The interaction of lanthanum chloride and neodymium chloride with sodium borohydride in tetrahydrofuran (THF) was a slow (23-30 hr) heterophase process. The interaction rate was affected by size reduction of the intial substances, temperature, reagent proportion and mixing rate. The reaction time was twice reduced with boiling tetrahydrofuran

Effect of Sodium Chloride Concentrations and Its Foliar Application Time on Quantitative and Qualitative Characteristics of Pomegranate Fruit (Punica granatum L. CV. “Malas Saveh”

Directory of Open Access Journals (Sweden)

V. Rouhi

2016-02-01

Full Text Available Introduction: Pomegranate (Punica granatum L. belong to Punicaceae family is native to Iran and grown extensively in arid and semi-arid regions worldwide. Pomegranate is also important in human medicine and its components have a wide range of clinical applications. Cracking causes a major fruit loss, which is a serious commercial loss to farmers. Fruit cracking, seems to be a problem that lessens the marketability to a great extent. Fruit cracking is one of the physiological disorders wherever pomegranate trees are grown. It may be due to moisture imbalances as this fruit is very sensitive to variation in soil moisture prolonged drought causes hardening of skin and if this is followed by heavy irrigation the pulp grows then skin grows and cracks. Many factors i.e., climate, soil and irrigation, varieties, pruning, insects and nutrition statues influence the growth and production of fruit trees. Deficiencies of various nutrients are related to soil types, plants and even to various cultivars. Most nutrients are readily fixed in soil having different PH. Plant roots are unable to absorb these nutrients adequately from the dry topsoil. Foliar fertilization is particularly useful under conditions where the absorption of nutrients through the soil and this difficult situation to be present in the nutrients such as calcium. Since the calcium element is needed, so spraying them at the right time is correct way to save the plant requirements. Therefore, a research conducted on effect of sodium chloride concentrations and its foliar application time on quantitative and qualitative characteristics of pomegranate fruit (Punica granatum L. CV. “Malas Saveh”. Materials and Methods: An experiment conducted at Jarghoyeh, Esfahan, Iran in 2012. The factors were Sodium chloride (0, 5 and 10 g/L and times of spray (15, 45 and 75 days before harvest. The study was factorial experiment in the base of randomized complete blocks design with three replications

Salt, sodium chloride or sodium? Content and relationship with chemical, instrumental and sensory attributes in cooked meat products.

Science.gov (United States)

Kameník, Josef; Saláková, Alena; Vyskočilová, Věra; Pechová, Alena; Haruštiaková, Danka

2017-09-01

The aim of this study was to determine the salt content in selected cooked meat products by the methods of determining the sodium content and the content of chlorides. The resulting data was compared with other chemical, instrumental and sensory parameters of the analysed samples. A total of 133 samples of 5 meat products were tested. The sodium content ranged from 558.0 to 1308.0mgNa/100g. Salt level determined by the two methods strongly correlated and did not differ in any meat product. Intensity of salty taste of the product was independent on its salt content. The salt (sodium) content may be reduced without a negative impact on sensory or instrumental properties of meat products. Copyright © 2017 Elsevier Ltd. All rights reserved.

Stability of polymyxin B sulfate diluted in 0.9% sodium chloride injection and stored at 4 or 25 degrees C.

Science.gov (United States)

He, Jie; Figueroa, Deborah A; Lim, Tze-Peng; Chow, Diana S; Tam, Vincent H

2010-07-15

The stability of polymyxin B sulfate in infusion bags containing 0.9% sodium chloride injection stored at 4 and 25 degrees C was studied. Seven manufacturing batches of polymyxin B from different sources were tested. The products were reconstituted in sterile water for injection, diluted in infusion bags containing 0.9% sodium chloride injection, and stored at room temperature (25 degrees C) or under refrigeration (4 degrees C). Samples were withdrawn at the same time on days 0, 1, 2, 3, 5, and 7. A modified microbiological assay was used to determine the concentrations, as indicated by zones of inhibition, of polymyxin B. Bordetella bronchiseptica served as the reference organism. Stability was defined as retention of >90% of the initial concentration. The decomposition kinetics of polymyxin B in 0.9% sodium chloride injection were evaluated by plotting the polymyxin B concentration remaining versus time. On average, the samples retained over 90% of their initial concentration for up to two days at both storage temperatures. All samples retained over 90% of their initial concentration at 24 hours. The decomposition kinetics of polymyxin B in infusion bags containing 0.9% sodium chloride injection exhibited pseudo-first-order kinetics, with rate constants of 0.024-0.075 day(-1) at 25 degrees C and 0.022-0.043 day(-1) at 4 degrees C (p > 0.05). Polymyxin B was stable for at least one day when stored at 4 or 25 degrees C in infusion bags containing 0.9% sodium chloride injection. Stability did not differ significantly between the two storage temperatures.

Assessing the effectiveness of 30% sodium chloride aqueous solution for the preservation of fixed anatomical specimens: a 5-year follow-up study.

Science.gov (United States)

de Oliveira, Fabrício Singaretti

2014-07-01

Anatomical specimens used in human or veterinary anatomy laboratories are usually prepared with formaldehyde (a cancerous and teratogenic substance), glycerin (an expensive and viscous fluid), or ethanol (which is flammable). This research aimed to verify the viability of an aqueous 30% sodium chloride solution for preservation of anatomical specimens previously fixed with formaldehyde. Anatomical specimens of ruminant, carnivorous, equine, swine and birds were used. All were previously fixed with an aqueous 20% formaldehyde solution and held for 7 days in a 10% aqueous solution of the same active ingredient. During the first phase of the experiment, small specimens of animal tissue previously fixed in formaldehyde were distributed in vials with different concentrations of formaldehyde, with or without 30% sodium chloride solution, a group containing only 30% sodium chloride, and a control group containing only water. During this phase, no contamination was observed in any specimen containing 30% sodium chloride solution, whether alone or in combination with different concentrations of formaldehyde. In the second phase of the experiment, the 30% sodium chloride solution, found to be optimal in the first phase of the experiment, was tested for its long-term preservation properties. For a period of 5 years, the preserved specimens were evaluated three times a week for visual contamination, odors, and changes in color and texture. There was no visual contamination or decay found in any specimen. Furthermore, no strange odors, or changes in color or softness were noted. The 30% sodium chloride solution was determined to be effective in the preservation of anatomic specimens previously fixed in formaldehyde. © 2014 Anatomical Society.

How Sodium Chloride Salt Inhibits the Formation of CO2 Gas Hydrates.

Science.gov (United States)

Holzammer, Christine; Finckenstein, Agnes; Will, Stefan; Braeuer, Andreas S

2016-03-10

We present an experimental Raman study on how the addition of sodium chloride to CO2-hydrate-forming systems inhibits the hydrate formation thermodynamically. For this purpose, the molar enthalpy of reaction and the molar entropy of reaction for the reaction of weakly hydrogen-bonded water molecules to strongly hydrogen bonded water molecules are determined for different salinities from the Raman spectrum of the water-stretching vibration. Simultaneously, the influence of the salinity on the solubility of CO2 in the liquid water-rich phase right before the start of hydrate formation is analyzed. The results demonstrate that various mechanisms contribute to the inhibition of gas hydrate formation. For the highest salt concentration of 20 wt % investigated, the temperature of gas hydrate formation is lowered by 12 K. For this concentration the molar enthalpy and entropy of reaction become smaller by 50 and 20%, respectively. Concurrently, the solubility of carbon dioxide is reduced by 70%. These results are compared with data in literature for systems of sodium chloride in water (without carbon dioxide).

Lack of the sodium-driven chloride bicarbonate exchanger NCBE impairs visual function in the mouse retina.

Directory of Open Access Journals (Sweden)

Gerrit Hilgen

Full Text Available Regulation of ion and pH homeostasis is essential for normal neuronal function. The sodium-driven chloride bicarbonate exchanger NCBE (Slc4a10, a member of the SLC4 family of bicarbonate transporters, uses the transmembrane gradient of sodium to drive cellular net uptake of bicarbonate and to extrude chloride, thereby modulating both intracellular pH (pH(i and chloride concentration ([Cl(-](i in neurons. Here we show that NCBE is strongly expressed in the retina. As GABA(A receptors conduct both chloride and bicarbonate, we hypothesized that NCBE may be relevant for GABAergic transmission in the retina. Importantly, we found a differential expression of NCBE in bipolar cells: whereas NCBE was expressed on ON and OFF bipolar cell axon terminals, it only localized to dendrites of OFF bipolar cells. On these compartments, NCBE colocalized with the main neuronal chloride extruder KCC2, which renders GABA hyperpolarizing. NCBE was also expressed in starburst amacrine cells, but was absent from neurons known to depolarize in response to GABA, like horizontal cells. Mice lacking NCBE showed decreased visual acuity and contrast sensitivity in behavioral experiments and smaller b-wave amplitudes and longer latencies in electroretinograms. Ganglion cells from NCBE-deficient mice also showed altered temporal response properties. In summary, our data suggest that NCBE may serve to maintain intracellular chloride and bicarbonate concentration in retinal neurons. Consequently, lack of NCBE in the retina may result in changes in pH(i regulation and chloride-dependent inhibition, leading to altered signal transmission and impaired visual function.

Antibacterial effect of roselle extracts (Hibiscus sabadariffa), sodium hypochlorite and acetic acid against multidrug-resistant Salmonella strains isolated from tomatoes.

Science.gov (United States)

Gutiérrez-Alcántara, E J; Rangel-Vargas, E; Gómez-Aldapa, C A; Falfan-Cortes, R N; Rodríguez-Marín, M L; Godínez-Oviedo, A; Cortes-López, H; Castro-Rosas, J

2016-02-01

Antibiotic-resistant Salmonella strains were isolated from saladette and red round type tomatoes, and an analysis done of the antibacterial activity of roselle calyx extracts against any of the identified strains. One hundred saladette tomato samples and 100 red round tomato samples were collected from public markets. Each sample consisted of four whole tomatoes. Salmonella was isolated from the samples by conventional culture procedure. Susceptibility to 16 antibiotics was tested for the isolated Salmonella strains by standard test. The antibacterial effect of four roselle calyx extracts (water, methanol, acetone and ethyl acetate), sodium hypochlorite and acetic acid against antibiotic-resistant Salmonella isolates was evaluated on contaminated tomatoes. Twenty-four Salmonella strains were isolated from 12% of each tomato type. Identified Salmonella serotypes were Typhimurium and Typhi. All isolated strains exhibited resistance to at least three antibiotics and some to as many as 12. Over contaminated tomatoes, the roselle calyx extracts produced a greater reduction (2-2·6 log) in antibiotic-resistant Salmonella strain concentration than sodium hypochlorite and acetic acid. The presence of multidrug-resistant Salmonella in vegetables is a significant public health concern. Multidrug-resistant Salmonella strains were isolated from raw tomatoes purchased in public markets in Mexico and challenged with roselle Hibiscus sabdariffa calyx extracts, sodium hypochlorite and acetic acid. On tomatoes, the extracts caused a greater reduction in the concentration of antibiotic-resistant Salmonella strains than sodium hypochlorite and acetic acid. Roselle calyx extracts are a potentially useful addition to disinfection procedures of raw tomatoes in the field, processing plants, restaurants and homes. © 2015 The Society for Applied Microbiology.

Sodium acetate induces a metabolic alkalosis but not the increase in fatty acid oxidation observed following bicarbonate ingestion in humans.

Science.gov (United States)

Smith, Gordon I; Jeukendrup, Asker E; Ball, Derek

2007-07-01

We conducted this study to quantify the oxidation of exogenous acetate and to determine the effect of increased acetate availability upon fat and carbohydrate utilization in humans at rest. Eight healthy volunteers (6 males and 2 females) completed 2 separate trials, 7 d apart in a single-blind, randomized, crossover design. On each occasion, respiratory gas and arterialized venous blood samples were taken before and during 180 min following consumption of a drink containing either sodium acetate (NaAc) or NaHCO3 at a dose of 2 mmol/kg body mass. Labeled [1,2 -13C] NaAc was added to the NaAc drink to quantify acetate oxidation. Both sodium salts induced a mild metabolic alkalosis and increased energy expenditure (P < 0.05) to a similar magnitude. NaHCO3 ingestion increased fat utilization from 587 +/- 83 kJ/180 min to 693 +/- 101 kJ/180 min (P = 0.01) with no change in carbohydrate utilization. Following ingestion of NaAc, the amount of fat and carbohydrate utilized did not differ from the preingestion values. However, oxidation of the exogenous acetate almost entirely (90%) replaced the additional fat that had been oxidized during the bicarbonate trial. We determined that 80.1 +/- 2.3% of an exogenous source of acetate is oxidized in humans at rest. Whereas NaHCO3 ingestion increased fat oxidation, a similar response did not occur following NaAc ingestion despite the fact both sodium salts induced a similar increase in energy expenditure and shift in acid-base balance.

Contribution on creep polygonization study in crystals. Creep of single crystalline silver chloride and sodium chloride

International Nuclear Information System (INIS)

Pontikis, Vassilis

1977-01-01

Subgrain formation and their influence on plastic behavior of materials has been studied in the case of single crystals of silver chloride and sodium chloride crept at high temperature (T > 0.5 T melting ). It is shown that the creep rate ε is a function of the mean subgrain diameter d. For secondary creep ε ∝ d k with k = 2 for NaCl and AgCl. During secondary creep, the substructure changes continuously: sub-boundaries migrate and sub-grains rotate. We find that sub-boundaries migration accounts for 35 pc of the total strain and that subgrain misorientation θ increases linearly with strain ε: θ ∝ 0.14 ε. The stability of permanent creep seems related to the power that the substructure is able to dissipate. The possible subgrain formation mechanisms are examined. It is shown that subgrain formation is closely related to the geometrical conditions of deformation and to the heterogeneities of this later. (author) [fr

[Antibacterial actin of vinegar against food-borne pathogenic bacteria including Escherichia coli O157:H7 (Part 2). Effect of sodium chloride and temperature on bactericidal activity].

Science.gov (United States)

Entani, E; Asai, M; Tsujihata, S; Tsukamoto, Y; Ohta, M

1997-05-01

Bactericidal effects of various kinds of AWASEZU (processed vinegar, 2.5% acidity) on food-borne pathogenic bacteria including Escherichia coli O157:H7 and other bacteria were examined. the order of bactericidal activities was NIHAIZU (3.5% NaCl was added) > SANBA-IZU (3.5% NaCl and 10% sucrose were added) > plain vinegar (spirit vinegar) > AMAZU (10% sucrose was added). This indicates that their activities were enhanced by the addition of sodium chloride and suppressed by the addition of sugar. On the other hand, when soy sauce was used instead of sodium chloride, the order of bactericidal activities was plain vinegar > AMAZU > NIHAIZU > SANBAIZU. This is mainly because their activities were suppressed by the increase in the pH value. The effect of sodium chloride (0.01-15%) and temperature (10-50 degrees C) on bactericidal activities against E. coli O157:H7 in spirit vinegar (0.5-2.5% acidity) was further examined. When vinegar was used in combination with sodium chloride, predominant synergism on the bactericidal activity was observed. Their activities were markedly enhanced by the addition of sodium chloride in proportion to the concentration. In addition to this, at higher temperatures spirit vinegar killed bacteria much more rapidly. It should be noted that the bactericidal activity of spirit vinegar was extremely enhanced by the combined use of the addition of sodium chloride and the rise of temperature. For example, in 2.5% acidity vinegar, the time required for 3 log decrease in viable cell numbers at 20 degrees C was shortened to 1/140-fold by the addition of 5% sodium chloride, shortened to 1/51-fold by the rise of the reaction temperature at 40 degrees C, and shortened to 1/830-fold; 0.89 minutes by both the addition of 5% sodium chloride and the rise of temperature at 40 degrees C. In order to propose the methods to prevent food poisoning by bacterial infection, bactericidal activities of vinegar solution containing sodium chloride on cooking tools and

Chemistry and Mechanism of Interaction Between Molybdenite Concentrate and Sodium Chloride When Heated in the Presence of Oxygen

Science.gov (United States)

Aleksandrov, P. V.; Medvedev, A. S.; Imideev, V. A.; Moskovskikh, D. O.

2017-04-01

Roasting of molybdenum concentrates with sodium chloride has high potential and can be an alternative to oxidizing roasting and autoclave leaching; however, the chemistry and mechanism are poorly known. The chemical mechanism of the roasting process between molybdenite concentrate and sodium chloride in the presence of atmospheric oxygen is proposed. It is demonstrated that the process occurs through molybdenite oxidation, up to molybdenum trioxide, with subsequent formation of sodium polymolybdates and molybdenum dioxydichloride from molybdenum trioxide. It is found that the formation of water-soluble sodium polymolybdates from molybdenum trioxide stops over time due to passivation of sodium chloride surface by polymolybdates. It is proved experimentally that preliminary grinding of the mixture in a furnace charge leads to an increase in the polymolybdate fraction of the roasting products, which constitutes approximately 65 pct of molybdenum initially in the roasted mixture against 20 to 22 pct in a nonground mixture (or 75 to 77 pct against 30 to 33 pct of molybdenum in calcine). For the first time, the presence of the Na2S2O7 phase in the calcine was confirmed experimentally. The suggested mechanism gives possible explanations for the sharp increase of MoO2Cl2 formation within the temperature range of 673 K to 723 K (400 °C to 450 °C) that is based on the catalytic reaction of molybdenum dioxydichloride from the Na2S2O7 liquid phase as it runs in a melt.

Bioaccumulation of sodium alkyl sulfate zinc chloride and their mixture in young goby proterorhinus marmoratus pall

Energy Technology Data Exchange (ETDEWEB)

Topcuoglu, S.; Birol, E. (Cekmece Nuclear Research and Training Center, Istanbul (Turkey))

1982-12-01

The bioaccumulation of labelled surfactant, 35S-labelled sodium lauryl sulfate and 65Zn-labelled zinc chloride, was investigated both as a mixture and alone by themselves in young goby. The concentration factor of 7.15 was calculated for the surfactant in the whole-body fish and there was no effect of zinc chloride on this bioaccumulation process. Biological half-life of the surfactant was around 35 hours. The effects of surfactants on the zinc accumulation were also followed under the same conditions. The results indicated that the sodium lauryl sulfate had no effect on the accumulation of zinc, however, the other surfactant, linear alkylbenzene sulfonate, caused a significant increase in the zinc accumulation in comparison with the control group, during the uptake period.

Bioaccumulation of sodium alkyl sulfate zinc chloride and their mixture in young goby proterorhinus marmoratus pall

International Nuclear Information System (INIS)

Topcuoglu, S.; Birol, E.

1982-01-01

The bioaccumulation of labelled surfactant, 35S-labelled sodium lauryl sulfate and 65Zn-labelled zinc chloride, was investigated both as a mixture and alone by themselves in young goby. The concentration factor of 7.15 was calculated for the surfactant in the whole-body fish and there was no effect of zinc chloride on this bioaccumulation process. Biological half-life of the surfactant was around 35 hours. The effects of surfactants on the zinc accumulation were also followed under the same conditions. The results indicated that the sodium lauryl sulfate had no effect on the accumulation of zinc, however, the other surfactant, linear alkylbenzene sulfonate, caused a significant increase in the zinc accumulation in comparison with the control group, during the uptake period. (author)

Benefit and risk assessment of increasing potassium intake by replacement of sodium chloride with potassium chloride in industrial food products in Norway.

Science.gov (United States)

Steffensen, Inger-Lise; Frølich, Wenche; Dahl, Knut Helkås; Iversen, Per Ole; Lyche, Jan Ludvig; Lillegaard, Inger Therese Laugsand; Alexander, Jan

2018-01-01

High sodium chloride (NaCl) intake is associated with health risks. NaCl may be replaced by potassium chloride (KCl) to decrease sodium intake. However, increased potassium may also have negative health effects. We conducted a benefit and risk assessment of increasing potassium by ratios of 30:70, 50:50, 70:30 (weight % K + : weight % Na + ) in children, adolescents and adults in Norway, using intake data from national food consumption surveys and available literature on potassium health effects. An intake of at least 3.5 g/day of potassium decreases risk of stroke and hypertension, and this level was used in the benefit assessment of the healthy population. Three g/day of potassium added to mean food intake is assumed safe, and these levels were used in the risk assessment. Not all persons reached the protective level of potassium, and increasing numbers exceeded the safe levels, in these scenarios. In addition, elderly above 85 years and infants below one year of age, as well as several patient groups and medication users, are particularly vulnerable to hyperkalemia. In conclusion, the number of Norwegians facing increased risk is far greater than the number likely to benefit from this replacement of sodium with potassium in industrially produced food. Copyright © 2017 Elsevier Ltd. All rights reserved.

Comparison of heparinized saline and 0.9% sodium chloride for maintaining peripheral intravenous catheter patency in dogs.

Science.gov (United States)

Ueda, Yu; Odunayo, Adesola; Mann, F A

2013-01-01

To determine whether heparinized saline would be more effective in maintaining the patency of peripheral IV catheters in dogs compared to 0.9% sodium chloride. Prospective blinded randomized study. University Veterinary Teaching Hospital. Thirty healthy purpose bred dogs, intended for use in the junior surgery laboratory, were utilized. The dogs were randomized into 1 of 3 groups, 2 treatment groups and a control group. An 18-Ga cephalic catheter was placed in the cephalic vein of each dog. Each dog in the treatment group had their catheter flushed with either 10 IU/mL heparinized saline or 0.9% sodium chloride every 6 hours for 42 hours. The dogs in the control group did not have their catheters flushed until the end of the study period. Immediately prior to flushing catheters, each catheter was evaluated for patency by aspiration of blood and the catheter site was evaluated for phlebitis. All dogs in the heparinized saline and 0.9% sodium chloride group had catheters that flushed easily at each evaluation point. More dogs in the saline group had catheters from which blood could not be aspirated, but there was no significant difference between these groups. All dogs in the control group had catheters that flushed easily at the end of the assigned 6 hour interval except in 1 dog. Phlebitis was not detected in any dog. Flushes of 0.9% sodium chloride were found to be as effective as 10 IU/mL heparinized saline flushes in maintaining patency of 18-Ga peripheral venous catheters in dogs for up to 42 hours. For peripheral catheters placed with the intention of performing serial blood draws, heparinized flushes may be warranted. © Veterinary Emergency and Critical Care Society 2013.

Ion chromatography for the precise analysis of chloride and sodium in sweat for the diagnosis of cystic fibrosis.

Science.gov (United States)

Doorn, J; Storteboom, T T R; Mulder, A M; de Jong, W H A; Rottier, B L; Kema, I P

2015-07-01

Measurement of chloride in sweat is an essential part of the diagnostic algorithm for cystic fibrosis. The lack in sensitivity and reproducibility of current methods led us to develop an ion chromatography/high-performance liquid chromatography (IC/HPLC) method, suitable for the analysis of both chloride and sodium in small volumes of sweat. Precision, linearity and limit of detection of an in-house developed IC/HPLC method were established. Method comparison between the newly developed IC/HPLC method and the traditional Chlorocounter was performed, and trueness was determined using Passing Bablok method comparison with external quality assurance material (Royal College of Pathologists of Australasia). Precision and linearity fulfill criteria as established by UK guidelines are comparable with inductively coupled plasma-mass spectrometry methods. Passing Bablok analysis demonstrated excellent correlation between IC/HPLC measurements and external quality assessment target values, for both chloride and sodium. With a limit of quantitation of 0.95 mmol/L, our method is suitable for the analysis of small amounts of sweat and can thus be used in combination with the Macroduct collection system. Although a chromatographic application results in a somewhat more expensive test compared to a Chlorocounter test, more accurate measurements are achieved. In addition, simultaneous measurements of sodium concentrations will result in better detection of false positives, less test repeating and thus faster and more accurate and effective diagnosis. The described IC/HPLC method, therefore, provides a precise, relatively cheap and easy-to-handle application for the analysis of both chloride and sodium in sweat. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Experimental investigations on prototype heat storage units utilizing stable supercooling of sodium acetate trihydrate mixtures

DEFF Research Database (Denmark)

Dannemand, Mark; Dragsted, Janne; Fan, Jianhua

2016-01-01

Laboratory tests of two heat storage units based on the principle of stable supercooling of sodium acetate trihydrate (SAT) mixtures were carried out. One unit was filled with 199.5 kg of SAT with 9% extra water to avoid phase separation of the incongruently melting salt hydrate. The other unit...

A novel and efficient method for the immobilization of thermolysin using sodium chloride salting-in and consecutive microwave irradiation.

Science.gov (United States)

Chen, Feifei; Zhang, Fangkai; Du, Fangchuan; Wang, Anming; Gao, Weifang; Wang, Qiuyan; Yin, Xiaopu; Xie, Tian

2012-07-01

Sodium chloride salting-in and microwave irradiation were combined to drive thermolysin molecules into mesoporous support to obtain efficiently immobilized enzyme. When the concentration of sodium chloride was 3 M and microwave power was 40 W, 93.2% of the enzyme was coupled to the support by 3 min, and the maximum specific activity of the immobilized enzyme was 17,925.1 U mg(-1). This was a 4.5-fold increase in activity versus enzyme immobilized using conventional techniques, and a 1.6-fold increase versus free enzyme. Additionally, the thermal stability of the immobilized thermolysin was significantly improved. When incubated at 70°C, there was no reduction in activity by 3.5h, whereas free thermolysin lost most of its activity by 3h. Immobilization also protected the thermolysin against organic solvent denaturation. The microwave-assisted immobilization technique, combined with sodium chloride salting-in, could be applied to other sparsely soluble enzymes immobilization because of its simplicity and high efficiency. Copyright © 2011 Elsevier Ltd. All rights reserved.

Efficacy of formalin, hydrogen-peroxide, and sodium-chloride on fungal-infected rainbow-trout eggs

Science.gov (United States)

Schreier, Theresa M.; Rach, J.J.; Howe, G.E.

1996-01-01

Antifungal agents are essential for the maintenance of healthy stocks of fish and their eggs in intensive aquaculture operations. In the usa, formalin is the only fungicide approved for use in fish culture, however, hydrogen peroxide and sodium chloride have been granted low regulatory priority drug status by the united states food and drug administration (fda) and their use is allowed. We evaluated the efficacy of these fungicides for controlling fungal infections on rainbow trout eggs. A pilot study was conducted to determine the minimum water flow rate required to administer test chemicals accurately in heath incubators. A minimum water flow rate of 7.6 1 min(-1) was necessary to maintain treatment concentrations during flow-through chemical exposures, the antifungal activity of formalin, hydrogen peroxide, and sodium chloride was evaluated by treating uninfected and 10% fungal-infected (saprolegnia parasitica) rainbow trout eggs (oncorhynchus mykiss) for 15 min every other day until hatch. There were no significant differences among treatments in percent hatch or final infection for uninfected eggs receiving prophylactic chemical treatments, eggs of the negative control group (uninfected and untreated) had a mean hatch exceeding 86%, all chemical treatments conducted on the infected egg groups controlled the spread of fungus and improved hatching success compared with the positive control groups (infected and untreated), formalin treatments of 1000 and 1500 mu l 1(-1) and hydrogen peroxide treatments of 500 and 1000 mu l 1(-1) were the most effective. Sodium chloride treatments of 30000 mg 1(-1) improved fry hatch, but the compound was less effective at inhibiting fungal growths compared with hydrogen peroxide and formalin treatments.

Stability of Diphenhydramine Hydrochloride, Lorazepam, and Dexamethasone Sodium Phosphate in 0.9% Sodium Chloride Stored in Polypropylene Syringes.

Science.gov (United States)

Anderson, Collin R; Halford, Zachery; MacKay, Mark

2015-01-01

Chemotherapy induced nausea and vomiting is problematic for many patients undergoing chemotherapy. Multiple-drug treatments have been developed to mitigate chemotherapy induced nausea and vomiting. A patient-controlled infusion of diphenhydramine hydrochloride, lorazepam, and dexamethasone sodium phosphate has been studied in patients who are refractory to first-line therapy. Unfortunately, the physical and chemical compatibility of this three-drug combination is not available in the published literature. Chemical compatibility was evaluated using high-performance liquid chromatography with ultraviolet detection. Visual observation was employed to detect change in color, clarity, or gas evolution. Turbidity and pH measurements were performed in conjunction with visual observation at hours 0, 24, and 48. Results showed that diphenhydramine hydrochloride 4 mg/mL, lorazepam 0.16 mg/mL, and dexamethasone sodium phosphate 0.27 mg/mL in 0.9% sodium chloride stored in polypropylene syringes were compatible, and components retained greater than 95% of their original concentration over 48 hours when stored at room temperature.

Sodium and potassium content and their ratio in meatballs in tomato sauce produced with lower amounts of sodium

Science.gov (United States)

Lilić, S.; Nikolić, D.; Pejkovski, Z.; Velebit, B.; Lakićević, B.; Korićanac, V.; Vranić, D.

2017-09-01

The goal of this study was to examine the possibility of partial replacement of sodium chloride with potassium chloride and ammonium chloride, with the target of achieving less sodium content in meatballs and tomato sauce as well as achieving a better Na:K ratio. The trial consisted of five groups. In the control group of meatballs and sauce, only sodium chloride was added. In group 1, half of the sodium chloride was replaced with potassium chloride related to control group while in group 2 one third of the sodium chloride was replaced with potassium chloride. In group 3, one third of the sodium chloride was replaced with ammonium chloride, and in group 4, sodium chloride was reduced to half the amount in the control group, and 1 g (0.25%) of ammonium chloride was also added. All products were acceptable according to sensory analyses. The largest reductions of sodium content were 44.64%, achieved in meatballs from group 1 and 50.62% in tomato sauce from group 4 in relation to meatballs and tomato sauce from control group. The highest Na:K ratio was calculated in meatballs and tomato sauce from control group, 2.88 and 4.39, respectively. The best Na:K ratio was in meatballs and tomato sauce from group 1, 0.60 and 0.92, respectively, in which half of sodium chloride was replaced with potassium chloride. However, in meatballs and tomato sauce from group 4, with only half the amount of sodium chloride related to control group, the Na:K ratio was worse because in these products, potassium chloride was not added.

Stability of tranexamic acid in 0.9% sodium chloride, stored in type 1 glass vials and ethylene/propylene copolymer plastic containers.

Science.gov (United States)

McCluskey, Susan V; Sztajnkrycer, Matthew D; Jenkins, Donald A; Zietlow, Scott P; Berns, Kathleen S; Park, Myung S

2014-01-01

Tranexamic acid has recently been demonstrated to decrease all-cause mortality and deaths due to hemorrhage in trauma patients. The optimal administration of tranexamic acid is within one hour of injury, but not more than three hours from the time of injury. To aid with timely administration, a premixed solution of 1 gram tranexamic acid and 0.9% sodium chloride was proposed to be stocked as a medication in both the aeromedical transport helicopters and Emergency Department at Mayo Clinic Hospital--Rochester Saint Marys Campus. Since no published stability data exists for tranexamic acid diluted with 0.9% sodium chloride, this study was undertaken to determine the stability of tranexamic acid diluted with 0.9% sodium chloride while being stored in two types of containers. Stability was determined through the use of a stability-indicating high-performance liquid reverse phase chromatography assay, pH, and visual tests. Tranexamic acid solutions of 1 gram in 0.9% sodium chloride 65 mL were studied at predetermined intervals for 90 days in ethylene/propylene copolymer plastic containers, protected from light, and at both controlled room and refrigerated temperatures. Tranexamic acid solutions of 1 gram in 0.9% sodium chloride 50 mL were studied at predetermined intervals for 180 days in clear Type 1 borosilicate glass vials sealed with intact elastomeric, Flourotec-coated stoppers, stored protected from light at controlled room temperature. Solutions stored in the ethylene/propylene copolymer plastic containers at both storage temperatures maintained at least 98% of initial potency throughout the 90-day study period. Solutions stored in glass vials at controlled room temperature maintained at least 92% of initial potency throughout the 180-day study period. Visual and pH tests revealed stable, clear, colorless, and particulate-free solutions throughout the respective study periods.

Sodium Chloride Supplementation Is Not Routinely Performed in the Majority of German and Austrian Infants with Classic Salt-Wasting Congenital Adrenal Hyperplasia and Has No Effect on Linear Growth and Hydrocortisone or Fludrocortisone Dose.

Science.gov (United States)

Bonfig, Walter; Roehl, Friedhelm; Riedl, Stefan; Brämswig, Jürgen; Richter-Unruh, Annette; Fricke-Otto, Susanne; Hübner, Angela; Bettendorf, Markus; Schönau, Eckhard; Dörr, Helmut; Holl, Reinhard W; Mohnike, Klaus

2018-01-01

Sodium chloride supplementation in salt-wasting congenital adrenal hyperplasia (CAH) is generally recommended in infants, but its implementation in routine care is very heterogeneous. To evaluate oral sodium chloride supplementation, growth, and hydrocortisone and fludrocortisone dose in infants with salt-wasting CAH due to 21-hydroxylase in 311 infants from the AQUAPE CAH database. Of 358 patients with classic CAH born between 1999 and 2015, 311 patients had salt-wasting CAH (133 females, 178 males). Of these, 86 patients (27.7%) received oral sodium chloride supplementation in a mean dose of 0.9 ± 1.4 mmol/kg/day (excluding nutritional sodium content) during the first year of life. 225 patients (72.3%) were not treated with sodium chloride. The percentage of sodium chloride-supplemented patients rose from 15.2% in children born 1999-2004 to 37.5% in children born 2011-2015. Sodium chloride-supplemented and -unsupplemented infants did not significantly differ in hydrocortisone and fludrocortisone dose, target height-corrected height-SDS, and BMI-SDS during the first 2 years of life. In the AQUAPE CAH database, approximately one-third of infants with salt-wasting CAH receive sodium chloride supplementation. Sodium chloride supplementation is performed more frequently in recent years. However, salt supplementation had no influence on growth, daily fludrocortisone and hydrocortisone dose, and frequency of adrenal crisis. © 2017 S. Karger AG, Basel.

Anion recognition using newly synthesized hydrogen bonding disubstituted phenylhydrazone-based receptors: poly(vinyl chloride)-based sensor for acetate.

Science.gov (United States)

Gupta, Vinod K; Goyal, Rajendra N; Sharma, Ram A

2008-08-15

A potentiometric acetate-selective sensor, based on the use of butane-2,3-dione,bis[(2,4-dinitrophenyl)hydrazone] (BDH) as a neutral carrier in poly(vinyl chloride) (PVC) matrix, is reported. Effect of various plasticizers and cation excluder, cetryaltrimethylammonium bromide (CTAB) was studied. The best performance was obtained with a membrane composition of PVC:BDH:CTAB ratio (w/w; mg) of 160:8:8. The sensor exhibits significantly enhanced selectivity toward acetate ions over a wide concentration range 5.0 x 10(-6) to 1.0 x 10(-1)M with a lower detection limit of 1.2 x 10(-6)M within pH range 6.5-7.5 with a response time of Fast and stable response, good reproducibility and long-term stability are demonstrated. The sensor has a response time of 15s and can be used for at least 65 days without any considerable divergence in their potential response. Selectivity coefficients determined with the separate solution method (SSM) and fixed interference method (FIM) indicate that high selectivity for acetate ion. The proposed electrode shows fairly good discrimination of acetate from several inorganic and organic anions. It was successfully applied to direct determination of acetate within food preservatives. Total concentration of acetic acid in vinegar samples were determined by direct potentiometry and the values agreed with those mentioned by the manufacturers.

Study of Physical Properties for Sodium acetate with Water and Water - Acetone mixtures at Different Temperatures

Directory of Open Access Journals (Sweden)

Ahmed Mohammed Abbas

2017-02-01

Full Text Available In this study binary and ternary solutions are prepared by using the sodium acetate concentrations (0.1, 0.125, 0.2, 0.25, 0.4, 0.5, 0.8, 1 M in water and acetone –water mixtures .The important parameters such as apparent molal volume, the partial molal volume transfer,  apparent  molal compressibility, free energy of activation of viscous flow and thermodynamic activation parameter (enthalpy and entropy determined of sodium acetate in water , 20%, 40% ,60% and 80% V/V acetone –water mixtures at 298.15K, 303.15K, and 308.15K from density and viscosity measurements espectively. The limiting apparent molal volumes and experimental slopes were derived from the Masson equation, have been interpreted in terms of solute–solvent and solute–solute interactions  respectively. The viscosity data were analyzed using theJones–Dole equation and the derived parameter B - coefficient has also been interpreted in terms of solute–solvent interactions in the solutions.

The effect on serum enzymes of intramuscular injections of digoxin, bumetanide, pentazocine and isotonic sodium chloride

DEFF Research Database (Denmark)

Andersen, Klaus Ejner; Damsgaard, T

1976-01-01

Intramuscular injections of digoxin, bumetanide, pentazocine or isotonic sodium chloride have been given to 39 patients. We followed the serum concentrations of creatine kinase (CK), aspartate aminotransferase (ASAT), lactate dehydrogenase (LDH) and LDH isoenzymes for 4 days. Ten patients receiving...

Reduction of potassium permanganate solution by γ-irradiated sodium chloride [Paper No. RD-21

International Nuclear Information System (INIS)

Phansalkar, V.K.; Ravishankar, D.

1982-01-01

The dissolution of γ-irradiated sodium chloride in potassium permanganate solution results in the reduction of MnO 4 - ions. This has been inferred from spectrophotometric studies. This has been explained on the basis of interaction of colour centres with MnO 4 - ions. The extent to which MnO 4 - ions are reduced are found to vary with

Chloride and sodium uptake potential over an entire rotation of Populus irrigated with landfill leachate

Science.gov (United States)

Jill A. Zalesny; Ronald S., Jr. Zalesny

2009-01-01

There is a need for information about the response of Populus genotypes to repeated application of high-salinity water and nutrient sources throughout an entire rotation. We have combined establishment biomass and uptake data with mid- and full-rotation growth data to project potential chloride (Cl−) and sodium (Na...

Antifungal activity of essential oils when associated with sodium chloride or fatty acids

Directory of Open Access Journals (Sweden)

Tantatoui-Elaraki, Abdelthafour

1994-12-01

Full Text Available The inhibition of mycelium growth in a Zygorhynchus sp. and an Aspergillus niger isolates was studied. The inhibition rates (IR caused by 4 essential oils (EO, 5 fatty acids and sodium chloride at various concentrations were determined in Sabouraud Dextrose Agar.
A synergy of action was observed between sodium chloride at 7.5% and the EO of thyme (0.04%, camomile (0.4% and mugwort (0.2 and 0.1% on A. niger and between sodium chloride (5% and the EO of camomile (0.1% and mugwort (0.1 and 0.01% and sodium chloride (7.5% and eucalyptus EO (0.4 and 0.2% on Zygorhynchus sp.
Camomile EO (0.13% associated with propionic acid (0.075%, lauric acid (0.05% or oleic acid (0.15% led to synergetic effect on Zygorhynchus sp. as well as thyme EO (0.04 and 0.05%, respectively with propionic acid (0.1% and linolenic acid (0.075% on A. niger. Other combinations exerted no higher effects than each of the substances used alone.
Practical applications of the results observed were discussed

Se ha estudiado la inhibición del crecimiento miceliar en un aislamiento de Zygorhynchus sp. y otro de Aspergillus niger. Se determinaron las tasas (o índices de inhibición (IR en Agar Sabouraud Dextrosa provocados por varias concentraciones de 4 aceites esenciales (EG, 5 ácidos grasos y cloruro sódico.
Se observó un efecto sinérgico entre cloruro sódico al 7.5% y los aceites esenciales de tomillo (0.04%, manzanilla (0.4% y artemisa (0.2 y 0.1% sobre A. niger, y entre cloruro sódico (5% y los aceites esenciales de manzanilla (0.1% y de artemisa (0.1 y 0.01%, así como cloruro sódico (7.5% y aceite esencial de eucalipto (0.4 y 0.2%, sobre Zygorhynchus sp.
El aceite esencial de manzanilla (0.13% en asociación con ácido propiónico (0.075%, ácido láurico (0.05% o ácido oleico (0.15% provocó un efecto sinérgico sobre Zygorhynchus sp., de la misma forma

Sodium and chloride accumulation in leaf, woody, and root tissue of Populus after irrigation with landfill leachate

International Nuclear Information System (INIS)

Zalesny, Jill A.; Zalesny, Ronald S.; Wiese, Adam H.; Sexton, Bart; Hall, Richard B.

2008-01-01

The response of Populus to irrigation sources containing elevated levels of sodium (Na + ) and chloride (Cl - ) is poorly understood. We irrigated eight Populus clones with fertilized well water (control) (N, P, K) or municipal solid waste landfill leachate weekly during 2005 and 2006 in Rhinelander, Wisconsin, USA (45.6 deg. N, 89.4 deg. W). During August 2006, we tested for differences in total Na + and Cl - concentration in preplanting and harvest soils, and in leaf, woody (stems + branches), and root tissue. The leachate-irrigated soils at harvest had the greatest Na + and Cl - levels. Genotypes exhibited elevated total tree Cl - concentration and increased biomass (clones NC14104, NM2, NM6), elevated Cl - and decreased biomass (NC14018, NC14106, DM115), or mid levels of Cl - and biomass (NC13460, DN5). Leachate tissue concentrations were 17 (Na + ) and four (Cl - ) times greater than water. Sodium and Cl - levels were greatest in roots and leaves, respectively. - Sodium and chloride supplied via landfill leachate irrigation is accumulated at high concentrations in tissues of Populus

Electrochemical corrosion behavior of A 516 steel using corrosive environments with varying concentrations of sodium thiosulphate

International Nuclear Information System (INIS)

Karim, F.; Arif, M.; Reza, I.; Akram, M.; Hussain, N.; Ali, L.

2012-01-01

The corrosion behavior of A 516 steel was studied by potentiodynamic polarization technique. Environment used for these tests was sodium chloride (5%), acetic acid (0.5%) and sodium thiosulphate with varying concentration from 0.001 M to 1 M. Surface study was also carried out using optical microscope. The potentiodynamic polarization results revealed the formation of large number of pits in the sample, which was tested in the solution containing NaCl. Pitting corrosion study of alloy A516 G-70 was also conducted to see the effect of different concentrations of thiosulfate with or without addition of NaCl and acetic acid at room temperature. It was observed that different thiosulfate concentrations did not produce any difference in the polarization behavior of the alloys, when added in 5% NaCl and 0.5% acetic acid solution. However, in the absence of NaCl and acetic acid, thiosulfate concentration 0.001 mol/l or higher did produce general corrosion and pitting in the alloy at room temperature is shown.(Orig./A.B.)

Viscometric investigation of compatibilization of the poly(vinyl chloride)/poly(ethylene-co-vinyl acetate) blends by terpolymer of maleic anhydride styrene vinyl acetate

Science.gov (United States)

İmren, Dilek; Boztuğ, Ali; Yılmaz, Ersen; Zengin, H. Bayram

2008-11-01

In this study, a blend of poly(vinyl chloride) (PVC)/ethylene-co-vinyl acetate (EVA) was compatibilized by terpolymer of maleic anhydride-styrene-vinyl acetate (MAStVA) used as a compatibilizer. It was prepared the blends of 50/50 PVC/EVA containing 2-10% of the terpolymer. The compatibility experiences of these blends were investigated by using viscometric method in the range of concentrations (0.5-2.0 g dL -1) where tetrahydrofuran (THF) is the solvent. The interaction parameter (Δ b) was used to study the miscibility and compatibility of polymer blend in solution, obtained from the modified Krigbaum and Wall theory. Turbidity and FTIR measurements were also used to investigate the miscibility of this pair of polymers. The values of the relative viscosities of the each polymer solution and their blends were measured by a Cannon-Fenske type viscometer. In consequence of the study, it was observed that a considerable improvement was achieved in the miscibility of PVC/EVA blends by adding among 5 and 10 wt% of compatibilizer.

Eliminating radium from uranium mill acid effluent with barium chloride-sodium carbonate precipitation

International Nuclear Information System (INIS)

Xiao Jiayuan

1998-01-01

The eliminating radium procedure, barium chloride-sodium carbonate-sand filtering, being used, radium can be eliminated to 3.7 x 10 -2 Bq/L order of magnitude from uranium mill acid effluents which contain 3.7 Bq/L Ra and pH 6∼9 when Ba 2+ is added by 3∼5 mg per litre, Na 2 CO 3 5mg. The radium elimination rate is more than 90%

Sorption of sulphur dioxide in calcium chloride and nitrate chloride liquids

International Nuclear Information System (INIS)

Trzepierczynska, I.; Gostomczyk, M.A.

1989-01-01

Flue gas desulphurization via application of suspensions has one inherent disadvantage: fixation of sulphur dioxide is very poor. This should be attributed to the low content of calcium ions which results from the solubility of the sorbing species. The solubility of sparingly soluble salts (CaO, CaCO 3 ) may be increased by decreasing the pH of the solution; yet, there is a serious limitation in this method: the corrosivity of the scrubber. The objective of this paper was to assess the sorbing capacity of two soluble calcium salts, calcium chloride and calcium nitrate, as a function of calcium ion concentration in the range of 20 to 82 kg/m 3 . It has been found that sorbing capacity increases with the increasing calcium ion concentration until the calcium concentration in the calcium chloride solution reaches the level of 60 kg/m 3 which is equivalent to the chloride ion content of ∼ 110 kg/m 3 . Addition of calcium hydroxide to the solutions brings about an increase in the sorbing capacity up to 1.6 kg/m 3 and 2.2 kg/m 3 for calcium chloride and calcium nitrate, respectively, as a result of the increased sorbent alkalinity. The sorption capacity of the solutions is considerably enhanced by supplementing them by acetate ions (2.8 to 13.9 kg/m 3 ). Increase in the sorption capacity of calcium nitrate solutions enriched with calcium acetate was approximately 30% as high as that of the chloride solutions enriched with calcium acetate was approximately 30% as high as that of the chloride solutions supplemented in the same way. (author). 12 refs, 7 refs, 4 tabs

Corrosion of nickel in potassium and sodium chloride melts containing vanadium trichloride

International Nuclear Information System (INIS)

Kochergin, V.P.; Ponomarev, Yu.S.; Bezvoritnij, V.A.; Bajbakov, D.P.

1976-01-01

Corrosion of nickel has been studied by the method of the rotating disc in melts of potassium and sodium chlorides containing vanadium trichloride in the concentration 0-20.0 wt.% in the temperature range 1103-1328 K. Corrosion proceeds in the diffusion region, the corrosion rate being controlled by diffusion of either V 3+ or V 2+ depending on the concentration of VCl 3 in the melts. The apparent activation energy of nickel corrosion is 43,110-74660 joule/mol

Behavioural and gill histopathological effects of acute exposure to sodium chloride in moneda (Metynnis orinocensis)

DEFF Research Database (Denmark)

Velasco-Santamaría, Yohana M.; Cruz-Casallas, Pablo E.

2008-01-01

To evaluate the toxicity of sodium chloride (NaCl), juveniles and adult Metynnis orinocensis were exposed for 96 h to 0, 5, 10, 15, 20 or 40 g L-1 of salt. Food intake, behaviour, opercular frequency (OF), mortality, body weight and gill microscopic alterations were evaluated. Behavioural changes...

Potentiometric titrations in anhydrous acetic acid

International Nuclear Information System (INIS)

Le Port, L.

1966-03-01

The method used for studying anhydrous acetic acid is potentiometry with a glass electrode. We have in this way studied the titration of common inorganic acids (HClO 4 - HBr - H 2 SO 4 - HCl - HNO 3 - H 3 PO 4 ) and of some metallic salts. Furthermore we have shown that complex acids are formed between HCl and some metallic chlorides. An analysis of the titration curves for the inorganic acids against pyridinium chloride has made it possible to calculate a certain number of values for the dissociation pK of these acids and of the corresponding pyridinium salts. The titration of metallic perchlorates constitutes a method of studying the stability of acetates; we have thus been able to draw up a classification for some of these acetates. The metallic chlorides studied fall into two groups according to their behaviour in weak or strong acids. The differences have been explained on the basis of the role played by solvolysis. In the third part we have studied the acidic properties of mixtures of HCl with certain metallic chlorides. This work has demonstrated the existence, in certain cases, of acid complexes of the type (HCl) m MCl n . (author) [fr

Acute toxicity of sodium chloride, pentachlorophenol, Guthion, and hexavalent chromium to fathead minnows (Pimephales promelas) and goldfish (Carassius auratus)

Energy Technology Data Exchange (ETDEWEB)

Adelman, I.R.; Smith, L.L. Jr.; Siesennop, G.D.

1976-02-01

The 96-h LC50's for sodium chloride were 7650 and 7341 mg/liter, for pentachlorophenol 0.21 and 0.22 mg/liter, for Guthion 1.9 and 2.4 mg/liter, and for hexavalent chromium 48 and 120 mg/liter, for fathead minnows (Pimephales promelas) and goldfish (Carassius auratus), respectively. Threshold LC50's were reached in 6 days for sodium chloride (7650 and 7322 mg/liter for fathead minnows and goldfish, respectively), and pentachlorophenol (0.21 and 0.21 mg/liter), but were not attained in 11 days (termination of testing) with Guthion (0.76 and 0.80 mg/liter) and hexavalent chromium (18 and 33 mg/liter). With pentachlorophenol and Guthion goldfish were initially more resistant, but by termination there was no significant difference in LC50's between the two species. With hexavalent chromium the goldfish were more resistant throughout the 11-day test, and with sodium chloride goldfish were initially more resistant but at attainment of a threshold LC50 were less resistant. Use of toxicity curves for assessment of acute mortality permits interpretation not possible in 96-h tests where LC50's are computed at 24-h intervals.

Sodium chloride and potassium sorbate: a synergistic combination against Enterococcus faecalis biofilms: an in vitro study

NARCIS (Netherlands)

van der Waal, S.V.; Jiang, L.M.; de Soet, J.J.; van der Sluis, L.W.M.; Wesselink, P.R.; Crielaard, W.

2012-01-01

Incomplete disinfection of the root canal system is a major cause of post-treatment disease. This study aimed to investigate the disinfecting property of organic acid salts and sodium chloride (NaCl), in a double-hurdle strategy, on Enterococcus faecalis biofilms. First of all, the high-throughput

Sodium chloride and potassium sorbate : a synergistic combination against Enterococcus faecalis biofilms: an in vitro study

NARCIS (Netherlands)

van der Waal, Suzette V.; Jiang, Lei-Meng; de Soet, Johannes J.; van der Sluis, Lucas W. M.; Wesselink, Paul R.; Crielaard, Wim

2012-01-01

Incomplete disinfection of the root canal system is a major cause of post-treatment disease. This study aimed to investigate the disinfecting property of organic acid salts and sodium chloride (NaCl), in a double-hurdle strategy, on Enterococcus faecalis biofilms. First of all, the high-throughput

Accounting for Electronic Polarization Effects in Aqueous Sodium Chloride via Molecular Dynamics Aided by Neutron Scattering

Czech Academy of Sciences Publication Activity Database

Kohagen, Miriam; Mason, Philip E.; Jungwirth, Pavel

2016-01-01

Roč. 120, č. 8 (2016), s. 1454-1460 ISSN 1520-6106 R&D Projects: GA ČR GBP208/12/G016 Institutional support: RVO:61388963 Keywords : molecular dynamics * neutron scattering * agueous sodium chloride Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.177, year: 2016

The effect of sodium chloride on the dissolution of calcium silicate hydrate gels

International Nuclear Information System (INIS)

Hill, J.; Harris, A.W.; Manning, M.; Chambers, A.; Swanton, S.W.

2006-01-01

The use of cement based materials will be widespread in the long-term management of radioactive materials in the United Kingdom. One of the applications could be the Nirex reference vault backfill (NRVB) as an engineered barrier within a deep geological repository. NRVB confers alkaline conditions, which would provide a robust chemical barrier through the control of the solubility of some key radionuclides, enhanced sorption and minimised corrosion of steel containers. An understanding of the dissolution of C-S-H gels in cement under the appropriate conditions (e.g., saline groundwaters) is necessary to demonstrate the expected evolution of the chemistry over time and to provide sufficient cement to buffer the porewater conditions for the required time. A programme of experimental work has been undertaken to investigate C-S-H gel dissolution behaviour in sodium chloride solutions and the effect of calcium/silicon ratio (C/S), temperature and cation type on this behaviour. Reductions in calcium concentration and pH values were observed with samples equilibrated at 45 deg. C compared to those prepared at 25 deg. C. The effect of salt cation type on salt-concentration dependence of the dissolution of C-S-H gels was investigated by the addition of lithium or potassium chloride in place of sodium chloride for gels with a C/S of 1.0 and 1.8. With a C/S of 1.0, similar increases in dissolved calcium concentration with increasing ionic strength were recorded for the different salts. However, at a C/S of 1.8, anomalously high calcium concentrations were observed in the presence of lithium

Influence of partial replacement of sodium chloride by potassium chloride in Minas fresh cheese of sheep’s milk

Directory of Open Access Journals (Sweden)

Dalana Cecília Hanauer

2017-08-01

Full Text Available The sheep’s milk has high contents of fat, protein and minerals in relation to the cow’s milk and is suitable for the production of cheeses, as the Minas fresh. The production of this cheese includes the salting, by offering important functions for this product. The salting is performed by adding sodium chloride (NaCl, however in excess this salt may be harmful to consumer health. Then, it was evaluated the development of tree formulations of Minas fresh cheese sheep’s milk (100% NaCl – QA; 75% NaCl and 25% potassium chloride (KCl – QB; 50% NaCl and 50% KCl – QC and they were evaluated by physical-chemical, microbiological and sensorial analyzes. A partial replacement of NaCl by KCl did not influence the moisture, protein and ash contents, pH and water activity of the cheeses. Furthermore, a 50% substitution of NaCl by KCl enabled to obtain a cheese with reduced sodium content in relation to the standard with 100% NaCl. The sensorial analysis showed that the substitution of 50% (QC and 25% (QB of NaCl by KCl did not show significant for the overall acceptance index, however, the use of KCl was perceived by the evaluators, since the formulations QB and QC differed significantly from the standard (QA. However, in the multiple comparison test there was no significant difference between the samples. Thus, the results indicated that a partial replacement of NaCl by KCl can be performed at Minas fresh cheese from sheep’smilk.

Effectiveness of Chlorinated Water, Sodium Hypochlorite, Sodium ...

African Journals Online (AJOL)

This study evaluated the efficacy of chlorinated water, sodium hypochlorite solution, sodium chloride solution and sterile distilled water in eliminating pathogenic bacteria on the surfaces of raw vegetables. Lettuce vegetables were dipped in different concentrations of chlorinated water, sodium hypochlorite solution, sodium ...

Facile and Efficient Acetylation of Primary Alcohols and Phenols with Acetic Anhydride Catalyzed by Dried Sodium Bicarbonate

Directory of Open Access Journals (Sweden)

Fulgentius Nelson Lugemwa

2013-12-01

Full Text Available A variety of primary alcohols and phenols were reacted with acetic anhydride at room temperature in the presence of sodium bicarbonate to produce corresponding esters in good to excellent yields. The acetylation of 4-nitrobenzyl alcohol was also carried out using other bicarbonates and carbonates. The reaction in the presence of cesium bicarbonate and lithium carbonate gave 4-nitrobenzyl acetate in excellent yield, while in the presence of Na2CO3, K2CO3, Cs2CO3, or KHCO3 the yield was in the range of 80%–95%. Calcium carbonate and cobaltous carbonate did not promote the acetylation of 4-ntirobenzyl alcohol using acetic anhydride. The acetylation of 4-nitrobenzyl alcohol was carried out using ethyl acetate, THF, toluene, diethyl ether, dichloromethane and acetonitrile, and gave good yields ranging from 75%–99%. Toluene was the best solvent for the reaction, while diethyl ether was the poorest.

Benzalkonium chloride neutralizes the irritant effect of sodium dodecyl sulfate.

Science.gov (United States)

McFadden, J P; Holloway, D B; Whittle, E G; Basketter, D A

2000-11-01

When benzalkonium chloride (BKC), a cationic surfactant, is added to sodium dodecyl sulfate (SDS), an anionic surfactant, and used in patch testing, on the basis of their known physicochemical interaction, it is possible to predict that there will be a tendency towards a reduction in the expected irritant response when compared to SDS alone. The aim of this study was to investigate whether BKC could reduce the irritant response to SDS when applied after the SDS exposure. 54 non-atopic adult volunteers were recruited for the study. 20% SDS was applied for 2 h under occlusion. 1% BKC was then applied to the same site. Various controls, including SDS application followed by water for 2 h, were included. The irritant reaction was assessed at 24 h and 48 h. 40 of the 54 subjects had some reaction when SDS was applied for 2 h followed by either benzalkonium chloride or water control under occlusion. In comparison to water control, where BKC was applied after SDS, 20 of the 40 responders had a weaker reaction but only 4 had a stronger response. This study shows that BKC applied to skin exposed to SDS attenuates the resulting irritant reaction.

The role of chloride in deoxycorticosterone hypertension: selective sodium loading by diet or drinking fluid

Czech Academy of Sciences Publication Activity Database

Kuneš, Jaroslav; Zicha, Josef; Jelínek, Jiří

2004-01-01

Roč. 53, č. 2 (2004), s. 149-154 ISSN 0862-8408 R&D Projects: GA ČR GA305/03/0769; GA MŠk LN00A069 Institutional research plan: CEZ:AV0Z5011922 Keywords : sodium * chloride * DOCA-salt hypertension Subject RIV: FA - Cardiovascular Diseases incl. Cardiotharic Surgery Impact factor: 1.140, year: 2004

Investigating Seed Germination Indices and Absorption Rate of Sodium, Chloride, Calcium, and Potassium in Different Parts of Seedlings of Sweet Corn KSC 403 (Zea Mays L var. Saccharata Under Salinity Stress and Seed Priming

Directory of Open Access Journals (Sweden)

M. Nasrolah alhossini,

2014-02-01

Full Text Available To investigate the effects of different levels of seed priming on germination indices and nutrient absorption at early growth stages of sweet corn (Golden Kernel Hybrid a factorial experiment based on completely randomized design was conducted with three replications in 2011. The experiment consists of 6 levels of primings (seeds without priming, priming with tap water, priming with distilled water, priming with sodium chloride, potassium chloride, and hydrous calcium chloride and five levels of salinity (zero, 4, 8, 12 and 16 ds/m sodium chloride. The characteristics studied were germination percentage, germination rate, root and shoot length, fresh weight and dry weight of seedling, root to shoot ratio and determination of sodium, chloride, calcium, and potassium concentration in different parts of seedlings (stems, roots and seed. The results indicated that increasing salinity stress levels decreased all parameters measured. Priming seeds with hydrated calcium chloride responded to significantly to salinity stress better than other treatments. Results also showed that increasing concentration of sodium chloride salt, increased absorption rate of sodium but concentration of calcium and potassium were reduced. Because application of hydrous calcium chloride stimulates cell in using calcium under salinity conditions it leads to improved seedling growth parameters. To achieve a more accurate results slicing interaction effect of seed priming×salinity levels was performed. Hydrous calcium chloride treatments improved all traits under study except sodium and potassium concentration. This represents a better performance of seeds germination under salinity stress when seeds primed with hydrous calcium chloride.

Properties of diclofenac sodium sorption onto natural zeolite modified with cetylpyridinium chloride.

Science.gov (United States)

Krajišnik, Danina; Daković, Aleksandra; Milojević, Maja; Malenović, Anđelija; Kragović, Milan; Bogdanović, Danica Bajuk; Dondur, Vera; Milić, Jela

2011-03-01

In this study an investigation of a model drug sorption onto cationic surfactant-modified natural zeolites as a drug formulation excipient was performed. Natural zeolite was modified with cetylpyridinium chloride in amounts equivalent to 100, 200 and 300% of its external cation-exchange capacity. The starting material and obtained organozeolites were characterized by Fourier transform infrared spectroscopy, zeta potential measurements and thermal analysis. In vitro sorption of diclofenac sodium as a model drug was studied for all surfactant/zeolite composites by means of sorption isotherm measurements in aqueous solutions (pH 7.4). The modified zeolites with three levels of surfactant coverage within the short activation time were prepared. Zeta potential measurements and thermal analysis showed that when the surfactant loading level was equal to external cation-exchange value, almost monolayer of organic phase were present at the zeolitic surface while higher amounts of surfactant produced less extended bilayers, ordered bilayers or admicelles at the zeolitic surface. Modified zeolites, obtained in this manner, were effective in diclofenac sodium sorption and the organic phase derived from adsorbed cetylpyridinium chloride was the primary sorption phase for the model drug. The Langmuir isotherm was found to describe the equilibrium sorption data well over the entire concentration range. The separate contributions of the adsorption and partition to the total sorption of DS were analyzed mathematically. Results revealed that that adsorption and partitioning of the model drug take place simultaneously. 2010 Elsevier B.V. All rights reserved.

Effect of calcium chloride concentration on output force in electrical actuator made of sodium alginate gel

Science.gov (United States)

Wu, Yuda; Zhao, Gang; Wei, Chengye; Liu, Shuang; Fu, Yu; Liu, Xvxiong

2018-01-01

As a kind of artificial muscle intelligent material, the biological gel electric driver has the advantages of low driving voltage, large strain, good biological compatibility, good flexibility, low price, etc. The application prospect is broad and it has high academic value. Alginate, as a common substance in sea, has characteristics of low cost, green and pollution-free. Therefore,this paper obtains biological gel electric actuator by sodium alginate and calcium chloride. Effects on output force of the electric actuator is researched by changing the crosslinking of calcium chloride concentration and the output force enhancement mechanism is analyzed in this paper.

Ethanol and sodium acetate as a preservation method to delay degradation of environmental DNA

Science.gov (United States)

Ladell, Bridget A.; Walleser, Liza R.; McCalla, S. Grace; Erickson, Richard A.; Amberg, Jon J.

2018-01-01

Environmental DNA (eDNA) samples that are collected from remote locations depend on rapid stabilization of the DNA. The degradation of eDNA in water samples is minimized when samples are stored at ≤ 4 °C. Developing a preservation technique to maintain eDNA integrity at room temperature would allow a wider range of locations to be sampled. We evaluated an ethanol and sodium acetate solution to maintain the integrity of the DNA samples for the time between collection and lab testing. For this evaluation, replicate water samples taken from a tank housing Asian carp were placed on ice or held at room temperature. At both temperatures, water samples were left untreated or were preserved with an ethanol and sodium acetate solution (EtOH–NaAc). Every day for 6 days following collection, a subset of the samples was removed from each preservation method and DNA was extracted and nuclear and mitochondrial markers were assayed with qPCR. Results showed comparable persistence of DNA between iced samples without the EtOH–NaAc treatment and samples that received EtOH–NaAc treatment that were kept at room temperature. We found that DNA can be amplified from preserved samples using an EtOH–NaAc solution after up to 7 days at room temperature.

Environmental, health, and safety issues of sodium-sulfur batteries for electric and hybrid vehicles. Volume 3, Transport of sodium-sulfur and sodium-metal-chloride batteries

Energy Technology Data Exchange (ETDEWEB)

Hammel, C J

1992-09-01

This report examines the shipping regulations that govern the shipment of dangerous goods. Since the elemental sodium contained in both sodium-sulfur and sodium-metal-chloride batteries is classified as a dangerous good, and is listed on both the national and international hazardous materials listings, both national and international regulatory processes are considered in this report The interrelationships as well as the differences between the two processes are highlighted. It is important to note that the transport regulatory processes examined in this report are reviewed within the context of assessing the necessary steps needed to provide for the domestic and international transport of sodium-beta batteries. The need for such an assessment was determined by the Shipping Sub-Working Group (SSWG) of the EV Battery Readiness Working Group (Working Group), created in 1990. The Working Group was created to examine the regulatory issues pertaining to in-vehicle safety, shipping, and recycling of sodium-sulfur batteries, each of which is addressed by a sub-working group. The mission of the SSWG is to establish basic provisions that will ensure the safe and efficient transport of sodium-beta batteries. To support that end, a proposal to the UN Committee of Experts was prepared by the SSWG, with the goal of obtaining a proper shipping name and UN number for sodium-beta batteries and to establish the basic transport requirements for such batteries (see the appendix for the proposal as submitted). It is emphasized that because batteries are large articles containing elemental sodium and, in some cases, sulfur, there is no existing UN entry under which they can be classified and for which modal transport requirements, such as the use of packaging appropriate for such large articles, are provided for. It is for this reason that a specific UN entry for sodium-beta batteries is considered essential.

Sodium

Science.gov (United States)

Table salt is a combination of two minerals - sodium and chloride Your body needs some sodium to work properly. It helps with the function ... in your body. Your kidneys control how much sodium is in your body. If you have too ...

Effect of temperature on the partial molar volume, isentropic compressibility and viscosity of DL-2-aminobutyric acid in water and in aqueous sodium chloride solutions

International Nuclear Information System (INIS)

Romero, Carmen M.; Rodríguez, Diana M.; Ribeiro, Ana C.F.; Esteso, Miguel A.

2017-01-01

Highlights: • Apparent volumes, apparent compressibilities, viscosities of DL-2-aminobutyric acid. • Effect of temperature on the values for these properties. • Hydrophobic and hydrophilic interactions and the effect of sodium chloride. - Abstract: Density, sound velocity and viscosity of DL-2-aminobutyric acid in water and in aqueous sodium chloride solutions have been measured at temperatures of (293.15, 298.15, 303.15, 308.15 and 313.15) K. The experimental results were used to determine the apparent molar volume and the apparent molar compressibility as a function of composition at these temperatures. The limiting values of both the partial molar volume and the partial molar adiabatic compressibility at infinite dilution of DL-2-aminobutyric acid in water and in aqueous sodium chloride solutions were determined at each temperature. The experimental viscosity values were adjusted by a least-squares method to a second order equation as proposed by Tsangaris-Martin to obtain the viscosity B coefficient which depends on the size, shape and charge of the solute molecule. The influence of the temperature on the behaviour of the selected properties is discussed in terms of both the solute hydration and the balance between hydrophobic and hydrophilic interactions between the acids and water, and the effect of the sodium chloride concentration.

Ultra-long-term human salt balance studies reveal interrelations between sodium, potassium, and chloride intake and excretion

NARCIS (Netherlands)

Birukov, Anna; Rakova, Natalia; Lerchl, Kathrin; Olde Engberink, Rik H. G.; Johannes, Bernd; Wabel, Peter; Moissl, Ulrich; Rauh, Manfred; Luft, Friedrich C.; Titze, Jens

2016-01-01

The intake of sodium, chloride, and potassium is considered important to healthy nutrition and cardiovascular disease risk. Estimating the intake of these electrolytes is difficult and usually predicated on urine collections, commonly for 24 h, which are considered the gold standard. We reported on

Physicochemical characteristics and sensory acceptability of ready-to-eat sliced frozen roast beef with partial reduction of sodium chloride

Directory of Open Access Journals (Sweden)

Camila Vespúcio BIS

2016-01-01

Full Text Available Abstract Sodium chloride in meat products provides microbiological stability and desirable technological and sensory effects. Therefore, the reduction of this ingredient is a challenge for the meat industry. The objective of this study was to evaluate the physicochemical and sensory characteristics of ready-to-eat sliced frozen roast beef with partial replacement of sodium chloride by a commercial additive mostly composed of potassium chloride. The analyses performed were chemical composition, cooking yield and post defrosting loss, microbiological evaluation and sensory analysis. There was higher moisture content (p < 0.05 in the control treatment (without the presence of the replacement additive and all treatments were not different (p ≥ 0.05 in the cooking yield and in post-defrosting loss. The results of microbiological analysis are according to Brazilian Legislation. The sensory evaluation showed no difference between the control treatment and the T1 treatment (with the reduction of 35% of NaCl, while the T2 treatment (with reduction of 70% of NaCl had the lowest average values in all attributes. The study showed that the reduction of 35% NaCl for commercial additive, mostly composed of potassium chloride, in roast beef is feasible since no changes were observed in sensory and technological characteristics evaluated.

Effect of gamma irradiation in sterilization of dry dextran as plasma substitute and sodium chloride

Energy Technology Data Exchange (ETDEWEB)

Piatkiewicz, A; Kusewicz, D [Politechnika Lodzka (Poland)

1975-01-01

The exposure of dry dextran, sodium chloride and polyethylene packing to 0,3-2 Mrad of gamma irradiation decreased their contamination by 60 to 96%. The sterilization effect of irradiation increased with gamma-ray dose. Spores of Bacillus subtilis and Aspergillus niger were shown to be the most resistant to gamma-ray treatment. In some samples the resistant Micrococcus was also detected.

Electrophoretic separation of alginic sodium diester and sodium hexametaphosphate in chondroitin sulfate that interfere with the cetylpyridinium chloride titration assay.

Science.gov (United States)

Weiguo, Zhang; Giancaspro, Gabriel; Adams, Kristie M; Neal-Kababick, James; Hildreth, Jana; Li, Aishan; Roman, Mark C; Betz, Joseph M

2014-01-01

The most commonly used chondroitin sulfate (CS) assay method is cetylpyridinium chloride (CPC) titration. Cellulose acetate membrane electrophoresis (CAME) is the technique used for detection of impurities in the U.S. Pharmacopeia's CS monograph. Because CPC titration is a relatively nonspecific quantitative technique, the apparent amount of CS as determined by CPC titration alone may not reflect the true amount of CS due to possible interference with the CPC assay by impurities that contain CPC titratable functional groups. When CAME is used in conjunction with CPC titration, certain non-CS and adulterants can be visualized and estimated, and a true value for CS can be assigned once the presence of these non-CS impurities has been ruled out. This study examines conjunct application of CPC and CAME in ascertaining CS assay and purity in the presence of certain adulterants. These include propylene glycol alginate sulfate sodium, known in commerce as alginic sodium diester (ASD), and Zero One (Z1), a water-soluble agent newly reported in the CS marketplace and subsequently identified as sodium hexametaphosphate. ASD, Z1, and CS are similar in physical appearance and solubility in water and ethanol. They are also titratable anions and form ionic pairs with CPC, therefore interfering with the CPC titration assay for CS CAME separates these adulterants from each other and from CS by differences in their electrophoretic mobility. CAME is able to detect these impurities in CS at levels as low as 0.66% by weight. Although it is recommended that a method for detecting impurities (e.g., CAME) be used in cormbination with relatively nonspecific assay methods such as CPC titration, this is seldom done in practice. Assay results for CS derived fromn CPC titration may, therefore, be misleading, leaving the CS supply chain vulnerable to adulteration. In this study, the authors investigated ASD and Z1 adulteration of CS and developed an electrophoretic separation of these

Hydration patterns and salting effects in sodium chloride solution.

Science.gov (United States)

Li, Weifeng; Mu, Yuguang

2011-10-07

The salting effects of 2M sodium chloride electrolyte are studied based on a series of model solutes with properties ranging from hydrophobic to hydrophilic. Generally, hydrophobic solutes will be salted out and hydrophilic solutes will be salted in by NaCl solution. The solvation free energy changes are highly correlated with Kirkwood-Buff integrals. The underlying mechanism resorts to the preferential binding of ions and water to solutes. Our results demonstrate that the salting effect not only depends on the salt's position in Hofmeister series, but also on the solutes' specifics. Taking the hydration free energies of solutes and ions as independent variables, a schematic diagram of salting effects is suggested. The resolved multifaceted salting effects rely on the sensitive balance of the tripartite interaction among solutes, ions, and water. © 2011 American Institute of Physics

Determination of lutetium (III) hydrolysis constants in the middle of ion force 1M sodium chloride at 303 K

International Nuclear Information System (INIS)

Jimenez R, M.; Solache R, M.J.; Ramirez G, J.J.; Rojas H, A.

1997-01-01

With the purpose to complete information about the lutetium (III) hydrolysis constants here is used the potentiometric method to determine those in the middle of ion force 1M sodium chloride at 303 K. (Author)

Differential Effects of Sodium Butyrate and Lithium Chloride on Rhesus Monkey Trophoblast Differentiation.

Directory of Open Access Journals (Sweden)

Priyadarsini Kumar

Full Text Available Trophoblast differentiation during early placental development is critical for successful pregnancy and aberrant differentiation causes preeclampsia and early pregnancy loss. During the first trimester, cytotrophoblasts are exposed to low oxygen tension (equivalent to~2%-3% O2 and differentiation proceeds along an extravillous pathway (giving rise to invasive extravillous cytotrophoblasts and a villous pathway (giving rise to multinucleated syncytiotrophoblast. Interstitial extravillous cytotrophoblasts invade the decidua, while endovascular extravillous cytotrophoblasts are involved in re-modelling uterine spiral arteries. We tested the idea that sodium butyrate (an epigenetic modulator induces trophoblast differentiation in early gestation rhesus monkey trophoblasts through activation of the Wnt/β-catenin pathway. The results show that syncytiotrophoblast formation was increased by butyrate, accompanied by nuclear accumulation of β-catenin, and increased expression of EnvV2 and galectin-1 (two factors thought to be involved in trophoblast fusion. Surprisingly, the expression of GCM1 and syncytin-2 was not affected by sodium butyrate. When trophoblasts were incubated with lithium chloride, a GSK3 inhibitor that mimics Wnt activation, nuclear accumulation of β-catenin also occurred but differentiation into syncytiotrophoblast was not observed. Instead the cells differentiated to mononucleated spindle-shaped cells and showed molecular and behavioral characteristics of endovascular trophoblasts. Another highly specific inhibitor of GSK3, CHIR99021, failed to induce endovascular trophoblast characteristics. These observations suggest that activation of the Wnt/β-catenin pathway correlates with both trophoblast differentiation pathways, but that additional factors determine specific cell fate decisions. Other experiments suggested that the differential effects of sodium butyrate and lithium chloride might be explained by their effects on TNF�

Studies of the effect of ethanol and sodium chloride on the micellization of sodium dodecyl sulfate by gel filtration

Energy Technology Data Exchange (ETDEWEB)

Suzuki, H.

1976-06-01

The effects of the addition of ethanol and sodium chloride to aqueous solutions of sodium dodecyl sulfate (SDS) were studied by the gel-filtration method. With an increase in the concentration of ethanol, the CMC decreased and then increased after passing a minimum, while the micellar weight increased and then decreased, showing a corresponding maximum. Above about 40 vol percent ethanol, no micelle formation was observed. The micellar weight and aggregation number in the presence of ethanol were measured in the SDS concentration range of a constant elution rate of micelles. A decrease in the CMC and an increase in the micellar weight of SDS were observed with an increase in the concentration of NaCl from 0 to 10 mmol/l. The gel-filtration study enabled us to make a direct experimental confirmation of the effects of ethanol and NaCl on the micelle formation of SDS.

BIOCHEMICAL PARAMETERS OF LIPID METABOLISM IN ANIMALS AFFECTED BY HEAVY METAL SALTS AND TREATED WITH CARNITINE CHLORIDE AND SODIUM ALGINATE

Directory of Open Access Journals (Sweden)

I. R. Bekus

2017-02-01

Full Text Available Background. Lipid metabolism disorders in the organism affected by environmental pollutants, including poisoning with cadmium and lead salts are of topical matter nowadays. Objective. The study was aimed to examine biochemical features of lipid metabolism in rats subjected to toxic damage by lead and cadmium salts and treated with carnitine chloride and Algigel. Methods. Experiments were carried out on white mature outbred male rats weighing 180-200 g. To cause the toxic damage the animals were administered with aqueous solution of cadmium chloride and lead acetate daily for the period of 30 days using intra-gastric lavage. The indices of lipid metabolism were detected by biochemical methods. Results. In animals treated with cadmium chloride and lead acetate the following changes were observed: HDL-cholesterol concentrations significantly decreased, resulting in 87% of the levels in the intact animals on the third day, 84% on the fifth and 80% on the seventh day. Conversely, concentrations of HDL-cholesterol and VLDL-cholesterol significantly increased during the experiment. Respectively, the ratios for HDL-cholesterol are 240%, 352%, and 388%; and for VLDL-cholesterol 108%, 116%, and 132%. Conclusions. Lipids profile of the rats displayed changes in the levels of cholesterol, triglycerides and lipoproteins of low, high and very low density.

Spectrophotometric determination of molybdenum(VI) with sodium 2-bromo-4, 5-dihydroxyazobenzene-4'-sulfonate in the presence of cetyltrimethylammonium chloride

International Nuclear Information System (INIS)

Wakamatsu, Yoshinobu

1977-01-01

Sodium 2-bromo-4,5-dihydroxyazobenzene-4'-sulfonate (abbreviated as BDAS) reacts with molybdenum(VI) in the presence of excessive cetyltrimethylammonium chloride(CTMAC) to form a water-soluble ternary complex. The combining ratio of molybdenum(VI) and BDAS in the ternary complex was shown to be 1 : 2. The ternary complex having its absorption maximum at 525 nm is quantitatively formed between pH 1.0 and 2.0. A constant absorbance was obtained when the concentrations of BDAS and CTMAC were more than 1.8 x 10 -4 M and (1.2 -- 1.6) x 10 -3 M, respectively. The procedure for the determination of molybdenum(VI) is as follows: Transfer the sample solution containing up to 28 μg of molybdenum(VI) to a 25 ml volumetric flask. Add 3 ml of 2.0 x 10 -3 M BDAS solution and an appropriate amount of a masking agent such as ascorbic acid, EDTA or sodium fluoride. Adjust the pH to about 1.6 with hydrochloric acid and sodium acetate. Add 3.5 ml of 0.01 M CTMAC solution and dilute the solution to the mark with water. Measure the absorbance at 525 nm against the reagent blank. A linear calibration curve was obtained over the concentration range 0 -- 28 μg of molybdenum(VI). The apparent molar absorptivity is 6.1 x 10 4 l cm -1 mol -1 at 525 nm, and the sensitivity of the reaction is 1.5 x 10 -3 μg cm -2 . The interference from metal ions such as iron(III), titanium(IV), zirconium(IV) and vanadium(V) could be eliminated by the addition of ascorbic acid, EDTA, sodium fluoride, or a mixture of these reagents. Tungsten(VI), however, interfered with the determination of molybdenum(VI) even when present at microgram levels. The present method was applied to the determination of molybdenum in three standard steel samples. Analytical results were satisfactory. (auth.)

EFFECTS OF SODIUM CHLORIDE ON GROWTH AND MINERAL NUTRITION OF PURPLETOP VERVAIN

Directory of Open Access Journals (Sweden)

Piotr Salachna

2016-04-01

Full Text Available There is a rising demand for salt-tolerant species for landscaping. Purpletop vervain is an excellent landscape plant for gardens and parks, with fragrant lavender to rose-purple flowers. However, little is known concerning the effect of sodium chloride on morphological characteristics, flowering and mineral uptake of purpletop vervain. In this study, carried out in 2013–2014, the plants of purpletop vervain were grown in pots in an unheated plastic tunnel. The plants were watered with 200 mM NaCl solution four times, every seven days. Salinity-exposed plants were characterized by slightly reduced plant height, weight of the aboveground part and visual score. Salt stress caused also an increase in leaf content sodium, chlorine and manganese. Salinity had no effect on earliness of flowering and content in leaves of phosphorus, potassium, magnesium, copper, zinc and iron. Purpletop vervain seems to be plant species able to tolerate salt stress under controlled conditions.

Ammonium-acetate is sensed by gustatory and olfactory neurons in Caenorhabditis elegans.

Directory of Open Access Journals (Sweden)

Christian Frøkjaer-Jensen

2008-06-01

Full Text Available Caenorhabditis elegans chemosensation has been successfully studied using behavioral assays that treat detection of volatile and water soluble chemicals as separate senses, analogous to smell and taste. However, considerable ambiguity has been associated with the attractive properties of the compound ammonium-acetate (NH(4Ac. NH(4Ac has been used in behavioral assays both as a chemosensory neutral compound and as an attractant.Here we show that over a range of concentrations NH(4Ac can be detected both as a water soluble attractant and as an odorant, and that ammonia and acetic acid individually act as olfactory attractants. We use genetic analysis to show that NaCl and NH(4Ac sensation are mediated by separate pathways and that ammonium sensation depends on the cyclic nucleotide gated ion channel TAX-2/TAX-4, but acetate sensation does not. Furthermore we show that sodium-acetate (NaAc and ammonium-chloride (NH(4Cl are not detected as Na(+ and Cl(- specific stimuli, respectively.These findings clarify the behavioral response of C. elegans to NH(4Ac. The results should have an impact on the design and interpretation of chemosensory experiments studying detection and adaptation to soluble compounds in the nematode Caenorhabditis elegans.

Co-doped sodium chloride crystals exposed to different irradiation temperature

Energy Technology Data Exchange (ETDEWEB)

Ortiz-Morales, A. [Unidad Profesional Interdisciplinaria de Ingenieria y Tecnologias Avanzadas, IPN, Av. Instituto Politecnico Nacional 2580, Col. La Laguna Ticoman, 07340 Mexico D.F., Mexico and Unidad de Irradiacion y Segurid (Mexico); Cruz-Zaragoza, E.; Furetta, C. [Unidad de Irradiacion y Seguridad Radiologica, Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, A.P. 70-543, 04510 Mexico D.F (Mexico); Kitis, G. [Nuclear Physics Laboratory, Aristotle University of Thessaloniki, Thessaloniki 54124 (Greece); Flores J, C.; Hernandez A, J.; Murrieta S, H. [Instituto de Fisica, Universidad Nacional Autonoma de Mexico, AP. 20-364, 01000 Mexico D.F (Mexico)

2013-07-03

Monocrystals of NaCl:XCl{sub 2}:MnCl{sub 2}(X = Ca,Cd) at four different concentrations have been analyzed. The crystals were exposed to different irradiation temperature, such as at room temperature (RT), solid water (SW), dry ice (DI) and liquid nitrogen (LN). The samples were irradiated with photon from {sup 60}Co irradiators. The co-doped sodium chloride crystals show a complex structure of glow curves that can be related to different distribution of traps. The linearity response was analyzed with the F(D) index. The F(D) value was less than unity indicating a sub-linear response was obtained from the TL response on the function of the dose. The glow curves were deconvoluted by using the CGCD program based on the first, second and general order kinetics.

An on-line potentiometric sequential injection titration process analyser for the determination of acetic acid.

Science.gov (United States)

van Staden, J F; Mashamba, Mulalo G; Stefan, Raluca I

2002-09-01

An on-line potentiometric sequential injection titration process analyser for the determination of acetic acid is proposed. A solution of 0.1 mol L(-1) sodium chloride is used as carrier. Titration is achieved by aspirating acetic acid samples between two strong base-zone volumes into a holding coil and by channelling the stack of well-defined zones with flow reversal through a reaction coil to a potentiometric sensor where the peak widths were measured. A linear relationship between peak width and logarithm of the acid concentration was obtained in the range 1-9 g/100 mL. Vinegar samples were analysed without any sample pre-treatment. The method has a relative standard deviation of 0.4% with a sample frequency of 28 samples per hour. The results revealed good agreement between the proposed sequential injection and an automated batch titration method.

Ultra-long-term human salt balance studies reveal interrelations between sodium, potassium, and chloride intake and excretion.

Science.gov (United States)

Birukov, Anna; Rakova, Natalia; Lerchl, Kathrin; Engberink, Rik Hg Olde; Johannes, Bernd; Wabel, Peter; Moissl, Ulrich; Rauh, Manfred; Luft, Friedrich C; Titze, Jens

2016-07-01

The intake of sodium, chloride, and potassium is considered important to healthy nutrition and cardiovascular disease risk. Estimating the intake of these electrolytes is difficult and usually predicated on urine collections, commonly for 24 h, which are considered the gold standard. We reported on data earlier for sodium but not for potassium or chloride. We were able to test the value of 24-h urine collections in a unique, ultra-long-term balance study conducted during a simulated trip to Mars. Four healthy men were observed while ingesting 12 g salt/d, 9 g salt/d, and 6 g salt/d, while their potassium intake was maintained at 4 g/d for 105 d. Six healthy men were studied while ingesting 12 g salt/d, 9 g salt/d, and 6 g salt/d, with a re-exposure of 12 g/d, while their potassium intake was maintained at 4 g/d for 205 d. Food intake and other constituents were recorded every day for each subject. All urine output was collected daily. Long-term urine recovery rates for all 3 electrolytes were very high. Rather than the expected constant daily excretion related to daily intake, we observed remarkable daily variation in excretion, with a 7-d infradian rhythm at a relatively constant intake. We monitored 24-h aldosterone excretion in these studies and found that aldosterone appeared to be the regulator for all 3 electrolytes. We report Bland-Altman analyses on the value of urine collections to estimate intake. A single 24-h urine collection cannot predict sodium, potassium, or chloride intake; thus, multiple collections are necessary. This information is important when assessing electrolyte intake in individuals. © 2016 American Society for Nutrition.

Method of modifying a vinyl chloride resin by utilizing radiation cross-linking polymerization

Energy Technology Data Exchange (ETDEWEB)

Kagiya, T; Fujimoto, T; Hosoi, F; Tsuneta, K; Atogawa, M

1970-08-26

The polyvinyl chloride is improved in its mechanical, thermal and chemical properties, with particular advantages gained in dimensional stability at temperatures higher than the plasticizing temperature. The process comprises irradiating a vinyl chloride resin with ionizing radiations in the presence of a vinyl acetate monomer. In this process, the irradiation of vinyl acetate effects cross-linking and the polymerization of the monomer simultaneously. The vinyl chloride resin may be a copolymer along with another monomer, a polyvinyl chloride derivative, a graft polymer of polyvinyl chloride, a mixture of vinyl chloride with another resin and a graft copolymer of vinyl chloride on another resin in any form. The addition of the vinyl acetate monomer to the vinyl chloride is not limited to any particular procedure. The vinyl acetate monomer may be added to the polyvinyl chloride in a quantity ranging from a trace to 200% by weight. The radiation dose may be 10/sup 2/ to 10/sup 9/, but preferably 10/sup 3/ roentgen. In one example, 36 parts by weight of market available vinyl acetate monomer immersed in 100 parts by weight of hard vinyl tube were placed in a stainless reacting vessel. After the replacement of inner air with nitrogen, the vessel was exposed to ..gamma.. beams of 4.8 x 10 roentgen from a Co-60 source. After dipping the exposed samples in boiled tetrahydrofuran for 48 hours, the insoluble substance in the samjle was 78.9% by weight. In addition, after heating at 180/sup 0/C for 30 minutes, the sample did not show any deformation.

Reaction of Hydrogen Chloride Gas with Sodium Carbonate and Its Deep Removal in a Fixed-Bed Reactor

Czech Academy of Sciences Publication Activity Database

Hartman, Miloslav; Svoboda, Karel; Pohořelý, Michael; Šyc, Michal; Chen, Po-Ch.

2014-01-01

Roč. 53, č. 49 (2014), s. 19145-19158 ISSN 0888-5885 R&D Projects: GA ČR GC14-09692J Grant - others:NSC(TW) 102WBS0300011 Institutional support: RVO:67985858 Keywords : hot fuel gas purification * hydrogen chloride gas * active sodium carbonate Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.587, year: 2014

Localized corrosion of alloys C-276 and 625 in aerated sodium chloride solutions at 25 to 200 degrees C

International Nuclear Information System (INIS)

Postlethwaite, J.

1991-12-01

Two molybdenum-bearing nickel alloys, Alloy C-276 and Alloy 625, were previously identified for consideration as candidate container materials for the Canadian Nuclear Fuel Waste Management Program. Because of the paucity of data for the localized corrosion behaviour of these passive alloys under conditions that may be experienced in a disposal vault, this project was undertaken to study the crevice and pitting corrosion of Alloys C-276 and 625 in chloride solutions at elevated temperatures. Electrochemical and immersion tests have been conducted in neutral sodium chloride solutions (0.1 wt% to saturated) at 25 to 200 degrees C, in an attempt to identify the conditions under which localized corrosion occurs and to relate the actual corrosion behaviour to that expected on the basis of electrochemical studies. Cyclic polarization studies showed that the passivation breakdown potentials move rapidly to more active values with increasing temperatures. Above 100 degrees C the resistance to localized corrosion is greatly reduced. The results of the immersion tests are presented in the form of T versus (C1-) diagrams. These susceptibility diagrams suggest that there is a limiting crevice-corrosion temperature for each alloy in aerated, neutral sodium chloride solutions. Below this temperature corrosion does not occur, regardless of the chloride concentration. The values of the limiting crevice-corrosion temperatures were in the range 100 to 125 degrees C for Alloy C-276 and 100 to 115 degrees C for Alloy 625. Such values suggest that saturation of the chloride solutions by surface boiling could occur without the initiation of localized corrosion. These electrochemical results indicate that a large safety margin for susceptibility to localized corrosion might be found below 100 degrees C

Model investigations for trace analysis of iodine, uranium, and technetium in saturated sodium chloride leaching solutions of stored radioactive waste

International Nuclear Information System (INIS)

Jegle, U.

1989-02-01

This paper describes the development of a time and cost saving chromatographic technique, which allows the matrix to be separated and the most important species to be analyzed in a leaching solution of vitrified radioactive waste. Uranium, iodine, and technetium were chosen for the model technique to be elaborated. In a first step, iodide and pertechnetate were separated from the matrix by the strongly basic AG 1X 8 anion exchange resin and then separated from each other by selective elution. The uranyl ions eluted with the sodium chloride matrix were separated from the excess of sodium chloride in a second step, again by adsorption to the strongly basic resin. The ion-selective electrode was found to be a suitable tool for iodide analysis. Pertechnetate was analysed by means of liquid scintillation. Uranium was determined by ICP-AES. (orig./RB) [de

Test Your Sodium Smarts

Science.gov (United States)

... You may be surprised to learn how much sodium is in many foods. Sodium, including sodium chloride ... foods with little or no salt. Test your sodium smarts by answering these 10 questions about which ...

Electrolytic process to produce sodium hypochlorite using sodium ion conductive ceramic membranes

Science.gov (United States)

Balagopal, Shekar; Malhotra, Vinod; Pendleton, Justin; Reid, Kathy Jo

2012-09-18

An electrochemical process for the production of sodium hypochlorite is disclosed. The process may potentially be used to produce sodium hypochlorite from seawater or low purity un-softened or NaCl-based salt solutions. The process utilizes a sodium ion conductive ceramic membrane, such as membranes based on NASICON-type materials, in an electrolytic cell. In the process, water is reduced at a cathode to form hydroxyl ions and hydrogen gas. Chloride ions from a sodium chloride solution are oxidized in the anolyte compartment to produce chlorine gas which reacts with water to produce hypochlorous and hydrochloric acid. Sodium ions are transported from the anolyte compartment to the catholyte compartment across the sodium ion conductive ceramic membrane. Sodium hydroxide is transported from the catholyte compartment to the anolyte compartment to produce sodium hypochlorite within the anolyte compartment.

Stability study of methotrexate in 0.9% sodium chloride injection and 5% dextrose injection with limit tests for impurities

DEFF Research Database (Denmark)

Nissen, Klaus; Bogedal Jorgensen, Lene; Lindegaard Berg, Dorthe

2017-01-01

Purpose. Results of an evaluation of the stability of methotrexate in 0.9% sodium chloride injection and 5% dextrose injection are presented. Methods. Methotrexate concentrated solution (100 mg/mL) was diluted to nominal concentrations of 0.2 and 20 mg/mL in infusion bags containing 0.9% sodium...... chloride injection or 5% dextrose injection. The filled bags were stored for 28 days at 25 °C and 60% relative humidity and protected from light. Samples were withdrawn for analysis on the day of preparation and after 3, 7, 14, 21, and 28 days. The test program included visual inspections, measurements...... in amounts of known and unknown degradation products were detected. In 5% dextrose injection, methotrexate at the higher concentration was stable for 28 days, with minor formation of degradation products; in the 0.2-mg/mL solution, however, methotrexate was stable for only 3 days. At later time points...

Maintenance fluid therapy and fluid creep impose more significant fluid, sodium, and chloride burdens than resuscitation fluids in critically ill patients: a retrospective study in a tertiary mixed ICU population.

Science.gov (United States)

Van Regenmortel, Niels; Verbrugghe, Walter; Roelant, Ella; Van den Wyngaert, Tim; Jorens, Philippe G

2018-04-01

Research on intravenous fluid therapy and its side effects, volume, sodium, and chloride overload, has focused almost exclusively on the resuscitation setting. We aimed to quantify all fluid sources in the ICU and assess fluid creep, the hidden and unintentional volume administered as a vehicle for medication or electrolytes. We precisely recorded the volume, sodium, and chloride burdens imposed by every fluid source administered to 14,654 patients during the cumulative 103,098 days they resided in our 45-bed tertiary ICU and simulated the impact of important strategic fluid choices on patients' chloride burdens. In septic patients, we assessed the impact of the different fluid sources on cumulative fluid balance, an established marker of morbidity. Maintenance and replacement fluids accounted for 24.7% of the mean daily total fluid volume, thereby far exceeding resuscitation fluids (6.5%) and were the most important sources of sodium and chloride. Fluid creep represented a striking 32.6% of the mean daily total fluid volume [median 645 mL (IQR 308-1039 mL)]. Chloride levels can be more effectively reduced by adopting a hypotonic maintenance strategy [a daily difference in chloride burden of 30.8 mmol (95% CI 30.5-31.1)] than a balanced resuscitation strategy [daily difference 3.0 mmol (95% CI 2.9-3.1)]. In septic patients, non-resuscitation fluids had a larger absolute impact on cumulative fluid balance than did resuscitation fluids. Inadvertent daily volume, sodium, and chloride loading should be avoided when prescribing maintenance fluids in view of the vast amounts of fluid creep. This is especially important when adopting an isotonic maintenance strategy.

Study of alkaline-earth element complexes in anhydrous acetic acid

International Nuclear Information System (INIS)

Petit, N.

1968-10-01

We have studied the complexes of alkaline-earth elements in anhydrous acetic acid. Using glass-electrode potentiometry we have studied the titration of alkaline earth acetates with perchloric acid which is the strongest acid in anhydrous acetic acid. These titrations have shown that the basic strength of these acetates increases as follows: Mg 4 ); the mixed acetate-acid sulfate complex of barium: Ba (OAc)(HSO 4 ); the mixed acetate-chloride of barium: Ba (OAc)(Cl). (author) [fr

Ultra-long–term human salt balance studies reveal interrelations between sodium, potassium, and chloride intake and excretion12

Science.gov (United States)

Birukov, Anna; Rakova, Natalia; Lerchl, Kathrin; Engberink, Rik HG Olde; Johannes, Bernd; Wabel, Peter; Moissl, Ulrich; Rauh, Manfred; Luft, Friedrich C; Titze, Jens

2016-01-01

Background: The intake of sodium, chloride, and potassium is considered important to healthy nutrition and cardiovascular disease risk. Estimating the intake of these electrolytes is difficult and usually predicated on urine collections, commonly for 24 h, which are considered the gold standard. We reported on data earlier for sodium but not for potassium or chloride. Objective: We were able to test the value of 24-h urine collections in a unique, ultra-long–term balance study conducted during a simulated trip to Mars. Design: Four healthy men were observed while ingesting 12 g salt/d, 9 g salt/d, and 6 g salt/d, while their potassium intake was maintained at 4 g/d for 105 d. Six healthy men were studied while ingesting 12 g salt/d, 9 g salt/d, and 6 g salt/d, with a re-exposure of 12 g/d, while their potassium intake was maintained at 4 g/d for 205 d. Food intake and other constituents were recorded every day for each subject. All urine output was collected daily. Results: Long-term urine recovery rates for all 3 electrolytes were very high. Rather than the expected constant daily excretion related to daily intake, we observed remarkable daily variation in excretion, with a 7-d infradian rhythm at a relatively constant intake. We monitored 24-h aldosterone excretion in these studies and found that aldosterone appeared to be the regulator for all 3 electrolytes. We report Bland–Altman analyses on the value of urine collections to estimate intake. Conclusions: A single 24-h urine collection cannot predict sodium, potassium, or chloride intake; thus, multiple collections are necessary. This information is important when assessing electrolyte intake in individuals. PMID:27225435

21 CFR 184.1138 - Ammonium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium chloride. 184.1138 Section 184.1138 Food... Specific Substances Affirmed as GRAS § 184.1138 Ammonium chloride. (a) Ammonium chloride (NH4Cl, CAS Reg. No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution. The...

Could vitamin C and zinc chloride protect the germ cells against sodium arsenite?

Science.gov (United States)

Altoé, L S; Reis, I B; Gomes, Mlm; Dolder, H; Pirovani, Jc Monteiro

2017-10-01

Arsenic (As) is commonly associated with natural and human processes such as volcanic emissions, mining and herbicides production, being an important pollutant. Several studies have associated As intake with male fertility reduction, thus the aim of the present study was to evaluate whether vitamin C and/or zinc would counteract As side effects within the testicles. Adult male Wistar rats were divided into six experimental groups: control, sodium arsenite (5 mg/kg/day), vitamin C (100 mg/kg/day), zinc chloride (ZnCl 2 ; 20 mg/kg/day), sodium arsenite + vitamin C and sodium arsenite + ZnCl 2 . Testicles and epididymis were harvested and either frozen or routinely processed to be embedded in glycol methacrylate resin. As reduced the seminiferous epithelium and tubules diameter due to germ cell loss. In addition, both the round spermatids population and the daily sperm production were reduced. However, ZnCl 2 and vitamin C showed to be effective against such side effects, mainly regarding to sperm morphology. Long-term As intake increased the proportions of abnormal sperm, whereas the concomitant intake of As with zinc or vitamin C enhanced the proportions of normal sperm, showing that such compounds could be used to protect this cell type against morphological defects.

Relations of enzymes inAspergillus repens grown under sodium chloride stress.

Science.gov (United States)

Kelavkar, U P; Chhatpar, H S

1993-09-01

Aspergillus repens, a salt-pan isolate, was halotolerant. When grown for 72 h (log phase) and 144 h (beginning of stationary phase) in a medium containing 2M sodium chloride, the activities of invertase, malate dehydrogenase (MDH), glucose-6-phosphate dehydrogenase (G6PDH), and glutamate dehydrogenase (GDH) were found to have increased. Control cultures grown in a medium devoid of 2M NaCl failed to show such changes. The activities of MDH, G6PDH, and GDH increased with rising concentrations of Na(+) (as NaCl) when added up to 100MM in vitro. At higher concentrations they decreased. Changes in kinetic constants, Km and Vmax of these enzymes, as well as their de novo synthesis, were found to be some of the responses to NaCl stress-mediated changes.

A comparative clinical study investigating the efficacy of a test dentifrice containing 8% strontium acetate and 1040 ppm sodium fluoride versus a marketed control dentifrice containing 8% arginine, calcium carbonate, and 1450 ppm sodium monofluorophosphate in reducing dentinal hypersensitivity.

Science.gov (United States)

Hughes, Nathan; Mason, Stephen; Jeffery, Peter; Welton, Helen; Tobin, Maira; O'Shea, Caoimhe; Browne, Mairead

2010-01-01

The objective of this clinical study was to evaluate and compare the efficacy in reducing dentin hypersensitivity of an 8% strontium acetate, 1040 ppm sodium fluoride dentifrice to a marketed control 8% arginine, calcium carbonate, 1450 ppm sodium monofluorophosphate dentifrice after twice-daily brushing for two, four, and eight weeks. This was a randomized, examiner-blind, two-arm parallel group, eight-week longitudinal clinical study with seventy-nine subjects, stratified based on baseline tooth sensitivity (Schiff score, Yeaple). Subjects brushed with either an 8% strontium acetate-based dentifrice or a marketed 8% arginine calcium carbonate dentifrice twice daily for approximately one minute. At screening, baseline, weeks two, four, and eight, subjects' tooth sensitivity was determined through both evaporative (Schiff and Visual Analogue Scale [VAS]) and tactile stimuli (Yeaple probe). Subject assessments using each stimulus were performed by the same examiner throughout the study. Seventy-seven subjects completed this clinical study. Both subject groups exhibited significant cumulative reductions from baseline to Days 14, 28, and 56 in dentin hypersensitivity as measured by Schiff, Yeaple, and VAS (for the 8% strontium acetate group, p carbonate group, p = 0.0031 for Yeaple at Day 14, p = 0.0015 for VAS at Day 14, and p 0.05) were observed between treatments for any of the time points and measures except for tactile sensitivity at Day 56, for which the 8% strontium acetate-based dentifrice was statistically superior (p = 0.0391) to the control 8% arginine calcium carbonate dentifrice. The 8% strontium acetate, 1040 ppm sodium fluoride dentifrice provided significant reductions in dentin hypersensitivity (p carbonate dentifrice showed no significant differences (p > 0.05) apart from tactile (Yeaple) sensitivity at week 8, where the 8% strontium acetate-based dentifrice showed significant improvement over the control (p = 0.0391).

Reverse osmosis performance of cellulose acetate membranes in the separation of uranium from dilute solutions

International Nuclear Information System (INIS)

Sastri, V.S.; Ashbrook, A.W.

1976-01-01

Batch 316-type cellulose acetate membranes were characterized in terms of pure water permeability constant, solute transport parameter, and mass transfer coefficient with a reference system of aqueous sodium chloride solution. These membranes were used in the determination of reverse osmosis characteristics such as product rate and solute separation in the case of uranium sulfate solutions of different concentrations (100 to 8000 ppM) in the feed solutions. A long-term test extending over a week has been carried out with dilute uranium solutions. Reverse osmosis treatment of synthetic mine water sample showed satisfactory performance of the membranes in the separation of metal ions

Electrical and spectroscopic characterization of polyaniline-polyvinyl chloride (PANI-PVC) blends doped with sodium thiosulphate

International Nuclear Information System (INIS)

Ameen, Sadia; Ali, Vazid; Zulfequar, M.; Mazharul Haq, M.; Husain, M.

2008-01-01

Polyaniline is doped with sodium thiosulphate in aqueous tetrahydrofuran (THF) and the blended films have been prepared by changing the amount of doped polyaniline (PANI) in the fixed amount of polyvinyl chloride (PVC). The electrical conductivity of various samples of polyaniline-polyvinyl chloride (PANI-PVC) blends has been studied to see the effect of dopant in the temperature range 300-400 K. Mott's parameters are used to explain the conduction mechanism. Different parameters such as pre-exponential factor (σ 0 ), activation energy (ΔE) and T 0 have also been calculated to see the effect of chemical doping. The crystallinity of the blends is explained on the basis of T 0 . The calculated values of T 0 show that crystallinity increases with an increase of doped PANI in PANI-PVC blends. Fourier transform-infrared (FTIR) spectroscopy is done to explore the nature and interaction of dopant into the polymeric chain

The impact of uni-univalent electrolytes on (water + acetic acid + toluene) equilibria: Representation with electrolyte-NRTL model

International Nuclear Information System (INIS)

Saien, Javad; Fattahi, Mahdi; Mozafarvandi, Maryam

2014-01-01

Highlights: • Experimental LLE data for water + acetic acid + toluene + NaCl or KCl were reported. • The salting-out effect was detected; indicating the stronger effect of NaCl. • The electrolyte-NRTL model was adequately used to correlate the phase equilibria. • A good agreement was observed between calculated and experimental tie-lines. - Abstract: The presence of salts can significantly alter the (liquid + liquid) equilibrium and extraction process. In this work, a study was conducted on the (liquid + liquid) equilibria of (water + acetic acid + toluene + sodium chloride or potassium chloride) at temperatures (288.2, 298.2 and 313.2) K. This chemical system, irrespective of salt, is frequently used in (liquid + liquid) extraction investigations. The selected salt concentrations in initial aqueous solutions were (0.9 and 1.7) mol · L −1 . The results show that salting-out effect of the salts was significant, so that an enhancement in the acetic acid distribution coefficient was achieved within (15.6 to 66.8)% with NaCl and within (2.5 to 37.6)% with KCl. Meantime, high separation factors were found at low temperatures and low solute concentrations. The electrolyte-NRTL model was satisfactorily used to correlate the phase equilibria. In this regard for each salt, the temperature dependent binary interaction parameters between components were calculated. The predicted tie-line mole fractions give root-mean square deviation (RMSD) values of only 0.0038 and 0.0045 for the systems containing NaCl and KCl, respectively

Experimental investigations on cylindrical latent heat storage units with sodium acetate trihydrate composites utilizing supercooling

DEFF Research Database (Denmark)

Dannemand, Mark; Johansen, Jakob Berg; Kong, Weiqiang

2016-01-01

Latent heat storage units utilizing stable supercooling of sodium acetate trihydrate (SAT) composites were tested in a laboratory. The stainless steel units were 1.5 m high cylinders with internal heat exchangers of tubes with fins. One unit was tested with 116 kg SAT with 6% extra water. Another...... in the thickened phase change material after melting. The heat content in the fully charged state and the heat released after solidification of the supercooled SAT mixtures at ambient temperature was higher for the unit with the thickened SAT mixture. The heat discharged after solidification of the supercooled SAT...

Stability of diclofenac sodium oral suspensions packaged in amber polyvinyl chloride bottles.

Science.gov (United States)

Donnelly, Ronald F; Pascuet, Elena; Ma, Carmen; Vaillancourt, Régis

2010-01-01

Prescribing of diclofenac for children usually involves a dose different from commercially available strengths. This drug is available only as tablets, which can be divided only so many times before the dose obtained becomes inaccurate. In addition, children may have difficulty swallowing tablets. For these reasons, a compounding formula for a liquid dosage form is essential to ensure effective delivery of the drug to pediatric patients. To develop a compounding formula for diclofenac sodium and to determine the extended physical and chemical stability of this compound when stored in amber polyvinyl chloride (PVC) prescription bottles under refrigeration and at room temperature. A suspension of diclofenac sodium (10 mg/mL) was prepared from commercially available diclofenac sodium tablets, with Ora-Blend as the suspending and flavouring agent. The suspension was packaged in 60-mL amber PVC prescription bottles and stored at either room temperature (23°C) or under refrigeration (5°C). Samples were collected on days 0, 7, 14, 21, 27, 56, and 93. Chemical stability was determined using a validated stability-indicating high-performance liquid chromatography method. At each sampling time, the suspensions were checked for changes in appearance (i.e., colour, layering, caking, ease of resuspension), odour, and pH. The diclofenac sodium suspensions were very stable, retaining at least 99.5% of the original concentration for up to 93 days, regardless of storage temperature. There were no apparent changes in the physical appearance of the suspensions, nor were there any substantial changes in odour or pH. Suspensions of diclofenac sodium (10 mg/mL) were quantitatively stable but difficult to prepare because of the enteric coating of the tablets. Therefore, it is recommended that diclofenac powder be used for the preparation of suspensions. For pediatric use, palatability is a consideration, and a masking agent should be added before administration. An expiry date of up to

13C-sodium acetate breath test for evaluation of gastric emptying times in dogs with gastric dilatation-volvulus.

Science.gov (United States)

Schmitz, S; Jansen, N; Failing, K; Neiger, R

2013-01-01

The aim of the study was to assess solid phase gastric emptying via non-invasive 13C-sodium acetate breath test in large breed dogs with or without gastric dilatation-volvulus (GDV). Dogs were recruited into one of the following groups: group 1 = healthy large breed dogs with no history of GDV, group 2 = dogs that underwent elective abdominal surgery for reasons unrelated to the gastrointestinal tract, and group 3 = dogs that underwent laparotomy and gastropexy to correct GDV. The dogs were fed a test meal containing 100 mg 13C-sodium acetate (for group 2 and 3, this was gastric emptying times were calculated and compared between groups. Gastric emptying times were significantly prolonged in dogs undergoing surgery (group 2) compared to group 1 and 3. Also, gastric emptying times of dogs with GDV were significantly prolonged compared to controls, but not to the same extent as dogs in group 2. There was a significant effect of abdominal surgery on gastric emptying times. Surprisingly, dogs after GDV surgery and gastropexy had shorter gastric emptying times than dogs undergoing laparotomy for reasons other than GDV, but still prolonged compared to healthy controls. The reason for these differences requires further study.

Laboratory test of a prototype heat storage module based on stable supercooling of sodium acetate trihydrate

DEFF Research Database (Denmark)

Dannemand, Mark; Kong, Weiqiang; Fan, Jianhua

2015-01-01

Laboratory test of a long term heat storage module utilizing the principle of stable supercooling of 199.5 kg of sodium acetate water mixture has been carried out. Avoiding phase separation of the incongruently melting salt hydrate by using the extra water principle increased the heat storage...... capacity. An external expansion vessel minimized the pressure built up in the module while heating and reduced the risk of instable supercooling. The module was stable supercooled at indoor ambient temperature for up to two months after which it was discharged. The energy discharged after activating...

Radiation-induced emulsion copolymerization of vinyl chloride with vinyl acetate in an engineering flow system

International Nuclear Information System (INIS)

Tsai, J.T.; Stahel, E.P.; Stannett, V.T.

1979-01-01

A flow reactor system was used to study the radiation-induced emulsion copolymerization of vinyl chloride with vinyl acetate. The emulsion was recirculated from a stirred vessel through transfer lines to a tubular reactor located within a high-intensity Co-60 source. The effects of physical chemical variables such as soap concentration, phase ratio, reaction temperature and residence time distribution on the molecular weight properties were investigated. The rate of copolymerization was found to be proportional to the 0.17 power of the soap concentration. Variation of the monomer-water ratio produced no significant change in rate. The rate increased with an increase in temperature over the range 5 to 50 0 C, while the average molecular weights of the copolymer increased with decreasing polymerization temperature. The molecular weight distribution in this engineering system was found to be essentially similar to those produced in a batch system

Effects of topical flurbiprofen sodium, diclofenac sodium, ketorolac ...

African Journals Online (AJOL)

To evaluate corneal sensitivity by using the Cochet-Bonnet® esthesiometer in normal canine eyes at different time points following instillation of three different topical non-steroidal anti-inflammatory drugs (flurbiprofen sodium 0.03%, diclofenac sodium 0.1% and ketorolac tromethamine 0.5%) and benzalkonium chloride ...

Corrosion of Dental Au-Ag-Cu-Pd Alloys in 0.9 % Sodium Chloride Solution

International Nuclear Information System (INIS)

Chiba, Atsushi; Kusayanagi, Yukiharu

2005-01-01

Two Au-Ag-Cu-Pd dental casting alloys (Au:12% and 20%) used. The test solutions used 0.9 % NaCl solution (isotonic sodium chloride solution), 0.9 % NaCl solution containing 1 % lactic acid, and 0.9 % NaCl solution containing 1 % lactic acid and 0.1 mol dm -3 Na 2 S. The surface of two samples in three sample solutions was not natural discoloration during one year. The alloy containing 12 % gold was easily alloyed and the composition was uniform comparing with the alloy containing 20 % gold. The rest potentials have not a little effect after three months. The kinds of metals could not definitely from the oxidation and reduction waves of metal on the cyclic voltammograms. The dissolutions of gold and palladium were 12 % Au sample in the 0.9 % NaCl solution containing 1 % lactic acid and 0.1 mol dm -3 Na 2 S. The pH of solution had an affect on dissolution of copper, and sulfur ion had an affect on dissolution of silver. The copper dissolved amount from 20 % gold sample was about 26 times comparing with that of 12 % gold sample in the 0.9 % solution containing 1 % lactic acid. Corrosion products were silver chloride and copper chloride in NaCl solution, and silver sulfide and copper sulfide in NaCl solution containing Na 2 S

Long-term stability of temocillin in dextrose 5% and in sodium chloride 0.9% polyolefin bags at 5 ± 3°C after freeze-thaw treatment.

Science.gov (United States)

Rolin, C; Hecq, J-D; Tulkens, P; Vanbeckbergen, D; Jamart, J; Galanti, L

2011-11-01

The aim of this study was to investigate the stability of a mixture of temocillin 20mg/ml in 5% dextrose and in 0.9% sodium chloride polyolefin bags after freezing, microwave thawing and long-term storage at 5±3°C. The stability of ten polyolefin bags containing 20mg/ml of temocillin, five bags in 5% dextrose and five bags in 0.9% sodium chloride, prepared under aseptic conditions was studied after freezing for 1 month at -20°C, thawing in a microwave oven with a validated cycle, and stored at 5±3°C. Over 30 days, temocillin concentrations were measured by high-pressure liquid chromatography. Visual inspections, microscope observation, spectrophotometric measurements and pH measurements were also performed. No precipitation occurred in the preparations but minor colour change was observed. No microaggregate was observed with optical microscopy or revealed by a change of absorbance. Based on a shelf life of 95% residual potency, temocillin infusions were stable at least 11 days in 5% dextrose and 14 days in 0.9% sodium chloride after freezing and microwave thawing (corresponding at the period where 95% lower confidence limit of the concentration-time profile remained superior to 95% of the initial concentration). During this period, the pH values of drug solutions have been observed to decrease without affecting chromatographic parameters. Within these limits, temocillin in 5% dextrose and in 0.9% sodium chloride infusions may be prepared and frozen in advance by a centralized intravenous admixture service then thawed before use in clinical units. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

Experimental Evaluation of Sodium Silicate-Based Nanosilica against Chloride Effects in Offshore Concrete

Science.gov (United States)

Kim, Kyoung-Min; Kim, Hak-Young; Heo, Young-Sun; Jung, Sang-Jin

2014-01-01

This study investigates the effect of a new pore filling material, named sodium silicate-based nanosilica (SS), on resisting the diffusion of the chloride ions. The proposed SS is chosen, mainly due to its smaller particle size, compared to the conventional ethyl silicate-based nanosilica. Each particle of SS is chemically treated to have the negative (−) charge on its surface. Four types of mixes with different amounts of partial replacement with fly ash and slag are prepared. Effect of water to binder ratios (0.35, 0.40, and 0.45) is also examined. Test results showed that the inclusion of SS was significantly beneficial for protecting the concrete from chloride attack. At a given strength, the SS inclusion in concrete was up to three times more effective than the control concrete without SS. It is believed that these excellent results are attributed to the small particle size and the chemical surface treatment of SS. In this study, experiments of compressive strength, hydration heat, accelerated neutralization, and sulfate erosion tests were also conducted to find the general effect of SS inclusion on the fundamental properties and durability of concrete. PMID:25574486

Experimental Evaluation of Sodium Silicate-Based Nanosilica against Chloride Effects in Offshore Concrete

Directory of Open Access Journals (Sweden)

Kyoung-Min Kim

2014-01-01

Full Text Available This study investigates the effect of a new pore filling material, named sodium silicate-based nanosilica (SS, on resisting the diffusion of the chloride ions. The proposed SS is chosen, mainly due to its smaller particle size, compared to the conventional ethyl silicate-based nanosilica. Each particle of SS is chemically treated to have the negative (− charge on its surface. Four types of mixes with different amounts of partial replacement with fly ash and slag are prepared. Effect of water to binder ratios (0.35, 0.40, and 0.45 is also examined. Test results showed that the inclusion of SS was significantly beneficial for protecting the concrete from chloride attack. At a given strength, the SS inclusion in concrete was up to three times more effective than the control concrete without SS. It is believed that these excellent results are attributed to the small particle size and the chemical surface treatment of SS. In this study, experiments of compressive strength, hydration heat, accelerated neutralization, and sulfate erosion tests were also conducted to find the general effect of SS inclusion on the fundamental properties and durability of concrete.

Oxidation of Borneol to Camphor Using Oxone and Catalytic Sodium Chloride: A Green Experiment for the Undergraduate Organic Chemistry Laboratory

Science.gov (United States)

Lang, Patrick T.; Harned, Andrew M.; Wissinger, Jane E.

2011-01-01

A new green oxidation procedure was developed for the undergraduate organic teaching laboratories using Oxone and a catalytic quantity of sodium chloride for the conversion of borneol to camphor. This simple 1 h, room temperature reaction afforded high quality and yield of product, was environmentally friendly, and produced negligible quantities…

Electroless nickel plating on abs plastics from nickel chloride and nickel sulfate baths

International Nuclear Information System (INIS)

Inam-ul-haque; Ahmad, S.; Khan, A.

2005-01-01

Aqueous acid nickel chloride and alkaline nickel sulphate bath were studied for electroless nickel planting on acrylonitrile-butadiene-styrene (ABS) plastic. Before electroless nickel plating, specimens were etched, sensitized and activated. Effects of sodium hypophosphite and sodium citrate concentration on the electroless nickel plating thickness were discussed. Aqueous acid nickel chloride bath comprising, nickel chloride 10 g/L, sodium hypophosphite 40 g/L, sodium citrate 40g/L at pH 5.5, temperature 85 deg. C and density of 1 Be/ for thirty minutes gave best coating thickness in micrometer. It was found that acid nickel chloride bath had a greater stability, wide operating range and better coating thickness results than alkaline nickel sulphate bath. Acid nickel chloride bath gave better coating thickness than alkaline nickel sulfate bath

Sodium Chloride Crystal-Induced SERS Platform for Controlled Highly Sensitive Detection of Illicit Drugs.

Science.gov (United States)

Yu, Borong; Li, Pan; Zhou, Binbin; Tang, Xianghu; Li, Shaofei; Yang, Liangbao

2018-04-03

A sodium chloride crystal-driven spontaneous 'hot spot' structure was demonstrated as a SERS-active platform, to get reproducible SERS signals, and eliminate the need for mapping large areas, in comparison with solution phase testing. During the process of solvent evaporation, the crystals produced induced silver aggregates to assemble around themselves. The micro-scale crystals can also act as a template to obtain an optical position, such that the assembled hot area is conveniently located during SERS measurements. More importantly, the chloride ions added in colloids can also replace the citrate and on the surface of the silver sol, and further decrease the background interference. High quality SERS spectra from heroin, methamphetamine (MAMP), and cocaine have been obtained on the crystal-driven hot spot structure with high sensitivity and credible reproducibility. This approach can not only bring the nanoparticles to form plasmonic hot spots in a controlled way, and thus provide high sensitivity, but also potentially be explored as an active substrate for label-free detection of other illicit drugs or additives. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Evaluation of the pH- and Thermal Stability of the Recombinant Green Fluorescent Protein (GFP) in the Presence of Sodium Chloride

Science.gov (United States)

Ishii, Marina; Kunimura, Juliana Sayuri; Jeng, Hélio Tallon; Vessoni Penna, Thereza Christina; Cholewa, Olivia

The thermal stability of recombinant green fluorescent protein (GFP) in sodium chloride (NaCl) solutions at different concentrations, pH, and temperatures was evaluated by assaying the loss of fluorescence intensity as a measure of denaturation. GFP, extracted from Escherichia coli cells by the three-phase partitioning method and purified through a butyl hydrophobic interaction chromatography (HIC) column, was diluted in water for injection (WFI) (pH 6.0-7.0) and in 10 mM buffer solutions (acetate, pH 5.0; phosphate, pH 7.0; and Tris-EDTA, pH 8.0) with 0.9-30% NaCl or without and incubated at 80-95°C. The extent of protein denaturation was expressed as a percentage of the calculated decimal reduction time (D-value). In acetate buffer (pH 4.84 ±0.12), the mean D-values for 90% reduction in GFP fluorescence ranged from 2.3 to 3.6 min, independent of NaCl concentration and temperature. GFP thermal stability diluted in WFI (pH 5.94±0.60) was half that observed in phosphate buffer (pH 6.08±0.60); but in both systems, D-values decreased linearly with increasing NaCl concentration, with D-values (at 80°C) ranging from 3.44, min (WFI) to 6.1 min (phosphate buffer), both with 30% NaCl. However, D-values in Tris-EDTA (pH 7.65±0.17) were directly dependent on the NaCl concentration and 5-10 times higher than D-values for GFP in WFI at 80°C. GFP pH-and thermal stability can be easily monitored by the convenient measure of fluorescence intensity and potentially be used as an indicator to monitor that processing times and temperatures were attained.

A potentiodynamic study of aluminum-lithium alloys in an aqueous sodium chloride environment

Science.gov (United States)

Tsao, C.-H. T.; Pizzo, P. P.

1985-01-01

The characteristics of the potentiodynamic curves for Al-Li alloys in 3.5 percent NaCl aqueous solution are explained and the electrochemical parameters of the potentiodynamic technique are correlated to observed pitting and intergranular cracking behavior. It is shown that the oxygen content of the sodium chloride electrolyte plays an important role in the electrochemical behavior of Al-Li alloys. The potentiodynamic behavior of the alloys is found to be insensitive to variation in compositional content and heat treatment, both of which affect the stress-corrosion behavior. Stringer oxide particle attack and random pitting are observed. It is shown that alternate-immersion exposure prior to potentiodynamic polarization may offer a means of assessing susceptibility to stress-corrosion cracking.

X-ray diffraction phase analysis of crystalline copper corrosion products after treatment in different chloride solutions

International Nuclear Information System (INIS)

Chmielova, M.; Seidlerova, J.; Weiss, Z.

2003-01-01

The corrosion products Cu 2 (OH) 3 Cl, Cu 2 O, and CuCl 2 were identified on the surface of copper plates after their four days treating in three different sodium chloride, sodium/magnesium, and sodium/calcium chloride solutions using X-ray diffraction powder analysis. However, the quantitative proportions of individual corrosion products differ and depend on the type of chloride solution used. Treating of copper plates only in the sodium chloride solution produced the mixture of corrosion products where Cu 2 O is prevailing over the Cu 2 (OH) 3 Cl and CuCl 2 was not identified. The sample developed after treating of the cooper surface in the sodium/magnesium chloride solution contains Cu 2 (OH) 3 Cl and CuCl 2 prevailing over the Cu 2 O, while the sample developed after treatment of copper in sodium/calcium chloride solution contains Cu 2 (OH) 3 Cl prevailing over CuCl 2 and Cu 2 O was not identified

Efficient and convenient oxidation of benzyl halides to carbonyl compounds with sodium nitrate and acetic acid by phase transfer catalysis in aqueous media

Directory of Open Access Journals (Sweden)

Yu Lin Hu

2010-08-01

Full Text Available A variety of benzyl halides were converted to the corresponding aldehydes/ketones in good to high yields by phase transfer catalysis combined with sodium nitrate and acetic acid at reflux. As a result, a simple and high yield procedure has been developed.

Oxygen, water, and sodium chloride transport in soft contact lenses materials.

Science.gov (United States)

Gavara, Rafael; Compañ, Vicente

2017-11-01

Oxygen permeability, diffusion coefficient of the sodium ions and water flux and permeability in different conventional hydrogel (Hy) and silicone-hydrogel (Si-Hy) contact lenses have been measured experimentally. The results showed that oxygen permeability and transmissibility requirements of the lens have been addressed through the use of siloxane containing hydrogels. In general, oxygen and sodium chloride permeability values increased with the water content of the lens but there was a percolation phenomenon from a given value of water uptake mainly in the Si-Hy lenses which appeared to be related with the differences between free water and bound water contents. The increase of ion permeability with water content did not follow a unique trend indicating a possible dependence of the chemical structure of the polymer and character ionic and non-ionic of the lens. Indeed, the salt permeability values for silicone hydrogel contact lenses were one order of magnitude below those of conventional hydrogel contact lenses, which can be explained by a diffusion of sodium ions occurring only through the hydrophilic channels. The increase of the ionic permeability in Si-Hy materials may be due to the confinement of ions in nanoscale water channels involving possible decreased degrees of freedom for diffusion of both water and ions. In general, ionic lenses presented values of ionic permeability and diffusivity higher than most non-ionic lenses. The tortuosity of the ionic lenses is lower than the non-ionic Si-Hy lenses. Frequency 55 and PureVision exhibited the highest water permeability and flux values and, these parameters were greater for ionic Si-Hy lenses than for ionic conventional hydrogel lenses. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 2218-2231, 2017. © 2016 Wiley Periodicals, Inc.

Enhancement of conductivity in polyaniline-[poly(vinylidene chloride)-co-(vinyl acetate)] blends by irradiation

International Nuclear Information System (INIS)

Bodugoez-Sentuerk, Hatice; Gueven, Olgun

2011-01-01

In this study we have prepared conductive poly(aniline), (PANI) blends with poly(vinylidene chloride-co-vinyl acetate), [P(VDC-co-VAc)] copolymer with varying compositions using gamma radiation to induce conductivity. A number of blends with different compositions were prepared by solution casting followed by irradiation in a 60 Co gamma cell to different doses up to 800 kGy. Electrical conductivity of the blends was measured before and after irradiation using a four-probe technique. Increasing radiation dose resulted in an increase of 9 orders of magnitude in the conductivity of P(VDC-co-VAc)/(PANI) films reaching 0.1 S/cm at 500 kGy and beyond this dose a decrease was observed. Effect of film thickness on conductivity of the blends was investigated and a slight increase of an order of magnitude was observed on increasing the film thickness from 50 to 200 μm. It was also observed that PANI blends exhibited a stretch dependent small increase in conductivity. The conductivity of the irradiated films was found to be stable for up to 12 months under ambient conditions.

Salt taste adaptation: the psychophysical effects of adapting solutions and residual stimuli from prior tastings on the taste of sodium chloride.

Science.gov (United States)

O'Mahony, M

1979-01-01

The paper reviews how adaptation to sodium chloride, changing in concentration as a result of various experimental procedures, affects measurements of the sensitivity, intensity, and quality of the salt taste. The development of and evidence for the current model that the salt taste depends on an adaptation level (taste zero) determined by the sodium cation concentration is examined and found to be generally supported, despite great methodological complications. It would seem that lower adaptation levels elicit lower thresholds, higher intensity estimates, and altered quality descriptions with predictable effects on psychophysical measures.

Validation of a CFD model simulating charge and discharge of a small heat storage test module based on a sodium acetate water mixture

DEFF Research Database (Denmark)

Dannemand, Mark; Fan, Jianhua; Furbo, Simon

2014-01-01

Experimental and theoretical investigations are carried out to study the heating of a 302 x 302 x 55 mm test box of steel containing a sodium acetate water mixture. A thermostatic bath has been set up to control the charging and discharging of the steel box. The charging and discharging has been...... for a Computational Fluid Dynamics (CFD) model. The CFD calculated temperatures are compared to measured temperatures internally in the box to validate the CFD model. Four cases are investigated; heating the test module with the sodium acetate water mixture in solid phase from ambient temperature to 52˚C; heating...... the module starting with the salt water mixture in liquid phase from 72˚C to 95˚C; heating up the module from ambient temperature with the salt water mixture in solid phase, going through melting, ending in liquid phase at 78˚C/82˚C; and discharging the test module from liquid phase at 82˚C, going through...

Assessing the toxicity of sodium chloride to the glochidia of freshwater mussels: Implications for salinization of surface waters

Energy Technology Data Exchange (ETDEWEB)

Gillis, Patricia L., E-mail: patty.gillis@ec.gc.ca [National Water Research Institute, Environment Canada, 867 Lakeshore Road, Burlington, ON L7R-4A6 (Canada)

2011-06-15

Chloride concentrations in surface waters have increased significantly, a rise attributed to road salt use. In Canada, this may be a concern for endangered freshwater mussels, many with ranges limited to southern Ontario, Canada's most road-dense region. The acute toxicity of NaCl was determined for glochidia, the mussel's larval stage. The 24 h EC50s of four (including two Canadian endangered) species ranged from 113-1430 mg Cl L{sup -1} (reconstituted water, 100 mg CaCO{sub 3} L{sup -1}). To determine how mussels would respond to a chloride pulse, natural river water (hardness 278-322 mg CaCO{sub 3} L{sup -1}) was augmented with salt. Lampsilis fasciola glochidia were significantly less sensitive to salt in natural water (EC50s 1265-1559 mg Cl L{sup -1}) than in reconstituted water (EC50 285 mg L{sup -1}). Chloride data from mussel habitats revealed chloride reaches levels acutely toxic to glochidia (1300 mg L{sup -1}). The increased salinization of freshwater could negatively impact freshwater mussels, including numerous species at risk. - Highlights: > Compared to other aquatic organisms glochidia are very sensitive to chloride. > Glochidia were less sensitive to salt in natural water than in reconstituted water. > Glochidia were less sensitive to salt in hard water than in soft water. > Road salt runoff may pose a threat to the reproduction of freshwater mussels. > Salinization of freshwater could negatively impact numerous species at risk. - Freshwater mussel larvae were acutely sensitive to sodium chloride, such that chloride levels in some Canadian rivers may pose a threat to the survival of this early life stage.

Assessing the toxicity of sodium chloride to the glochidia of freshwater mussels: Implications for salinization of surface waters

International Nuclear Information System (INIS)

Gillis, Patricia L.

2011-01-01

Chloride concentrations in surface waters have increased significantly, a rise attributed to road salt use. In Canada, this may be a concern for endangered freshwater mussels, many with ranges limited to southern Ontario, Canada's most road-dense region. The acute toxicity of NaCl was determined for glochidia, the mussel's larval stage. The 24 h EC50s of four (including two Canadian endangered) species ranged from 113-1430 mg Cl L -1 (reconstituted water, 100 mg CaCO 3 L -1 ). To determine how mussels would respond to a chloride pulse, natural river water (hardness 278-322 mg CaCO 3 L -1 ) was augmented with salt. Lampsilis fasciola glochidia were significantly less sensitive to salt in natural water (EC50s 1265-1559 mg Cl L -1 ) than in reconstituted water (EC50 285 mg L -1 ). Chloride data from mussel habitats revealed chloride reaches levels acutely toxic to glochidia (1300 mg L -1 ). The increased salinization of freshwater could negatively impact freshwater mussels, including numerous species at risk. - Highlights: → Compared to other aquatic organisms glochidia are very sensitive to chloride. → Glochidia were less sensitive to salt in natural water than in reconstituted water. → Glochidia were less sensitive to salt in hard water than in soft water. → Road salt runoff may pose a threat to the reproduction of freshwater mussels. → Salinization of freshwater could negatively impact numerous species at risk. - Freshwater mussel larvae were acutely sensitive to sodium chloride, such that chloride levels in some Canadian rivers may pose a threat to the survival of this early life stage.

Synthesis and thermolysis of sodium hexachloromolybdate

International Nuclear Information System (INIS)

Kushakbaev, A.; Terishkhanova, I.G.; Parpiev, N.A.; Adylova, Sh.N.

1985-01-01

Synthesis of Na 3 MoCl 6 and the process of its thermal decomposition are described. Sodium hexachloromolybdate is synthesized by means of molybdenum chloride compolunds (MoCl 5 ; MoCl 5 +Mo, MoCl 3 ) interaction with sodium chloride at moderate temperatures in nitrogen atmosphere. It is shown, that Na 3 MoCl 6 thermolysis in conventional conditions takes place in two stages: the first one (570-600 K) corresponds to the formation of mixture MoO 2 +NaMoCl 4 +5NaCl, the second one (930 K) - to MoO 3 +3NaCl formation. In an inert atmosphere at 920 K a mixture of metal molybdenum and sodium chloride is observed

Electrolyte transport in distal colon of sodium-depleted rats: Effect of sodium repletion

International Nuclear Information System (INIS)

Turnamian, S.G.; Binder, H.J.

1988-01-01

Dietary sodium depletion increases plasma aldosterone level and, as a result, induces amiloride-sensitive electrogenic sodium absorption and electrogenic potassium secretion and stimulates Na + -K + -ATPase activity in rat distal colon, while inhibiting electroneutral sodium chloride absorption. To assess the events that occur as the aldosterone-stimulated colon reverts to normal, unidirectional 22 Na and 36 Cl fluxes were measured under voltage-clamp conditions across isolated distal colonic mucosa of rats that were initially dietary sodium depleted for 7 days and then sodium repleted for varying periods of time before the study. Within 8 h of dietary sodium repletion, plasma aldosterone level and Na + -K + -ATPase activity declined to normal, amiloride-sensitive electrogenic sodium absorption decreased by >90%, and active electrogenic potassium secretion also decreased markedly. In contrast, electroneutral sodium chloride absorption did not completely return to levels seen in normal animals until ∼64-68 h. These results demonstrate that maintenance of electrogenic sodium absorption and potassium secretion are directly dependent on elevated plasma aldosterone levels. The inhibition of electroneutral sodium absorption, although initiated by excess aldosterone, persists after normalization of the plasma aldosterone level, thereby implying that the inhibition is dependent on additional factor(s)

Chloride sensing by WNK1 kinase involves inhibition of autophosphorylation

Science.gov (United States)

Piala, Alexander T.; Moon, Thomas M.; Akella, Radha; He, Haixia; Cobb, Melanie H.; Goldsmith, Elizabeth J.

2014-01-01

WNK1 [with no lysine (K)] is a serine-threonine kinase associated with a form of familial hypertension. WNK1 is at the top of a kinase cascade leading to phosphorylation of several cotransporters, in particular those transporting sodium, potassium, and chloride (NKCC), sodium and chloride (NCC), and potassium and chloride (KCC). The responsiveness of NKCC, NCC, and KCC to changes in extracellular chloride parallels their phosphorylation state, provoking the proposal that these transporters are controlled by a chloride-sensitive protein kinase. Here, we found that chloride stabilizes the inactive conformation of WNK1, preventing kinase autophosphorylation and activation. Crystallographic studies of inactive WNK1 in the presence of chloride revealed that chloride binds directly to the catalytic site, providing a basis for the unique position of the catalytic lysine. Mutagenesis of the chloride binding site rendered the kinase less sensitive to inhibition of autophosphorylation by chloride, validating the binding site. Thus, these data suggest that WNK1 functions as a chloride sensor through direct binding of a regulatory chloride ion to the active site, which inhibits autophosphorylation. PMID:24803536

An eco-friendly approach for sodium chloride free cotton dyeing

International Nuclear Information System (INIS)

Umer, T.

2014-01-01

Present study was conducted with an aim to develop an environmental friendly method of dyeing cotton as an alternative to standard reactive dyeing process that requires high level of salt. When dyeing was carried out in the absence of sodium chloride (NaCl), an extremely lighter depth of shade was experienced, and hence this particular research was focused on the reduction of the total colour difference (AE) to a minimum level. Instead of adding any other chemical or any additional process like cationization, salt-free reactive dyeing was carried out by varying three common process parameters (dyes, alkali, and process time) to achieve required depth of shade. The results obtained were compared with those of conventionally dyed fabrics in terms of depth of shade (AL), total colour difference (AE), washing fastness, and rubbing fastness. The results were found to be promising and comparable to those dyed with using NaCl. Moreover, the investigated method showed a significant reduction of Total Dissolved Solids (TDS) and Electrical Conductivity (EC) in the wastewater, and thus proved to be an environment friendly process. (author)

Tolerance Test of Eisenia Fetida for Sodium Chloride

Energy Technology Data Exchange (ETDEWEB)

Kerr, M.; Stewart, A.J.

2003-01-01

Saltwater spills that make soil excessively saline often occur at petroleum exploration and production (E&P) sites and are ecologically damaging. Brine scars appear when produced water from an E&P site is spilled onto surrounding soil, causing loss of vegetation and subsequent soil erosion. Revegetating lands damaged by brine water can be difficult. The research reported here considers earthworms as a bioremedial treatment for increasing the salt mobility in this soil and encouraging plant growth and a healthy balance of soil nutrients. To determine the practical application of earthworms to remediate brine-contaminated soil, a 17-d test was conducted to establish salt tolerance levels for the common compost earthworm (Eisenia fetida) and relate those levels to soil salinity at brine-spill sites. Soil samples were amended with sodium chloride in concentrations ranging from 1 to 15 g/kg, which represent contamination levels at some spill sites. The survival rate of the earthworms was near 90% in all tested concentrations. Also, reproduction was noted in a number of the lower-concentration test replicates but absent above the 3-g/kg concentrations. Information gathered in this investigation can be used as reference in further studies of the tolerance of earthworms to salty soils, as results suggest that E. fetida is a good candidate to enhance remediation at brine-damaged sites.

Inhibitive effect of N,N'-Dimethylaminoethanol on carbon steel corrosion in neutral sodium chloride solution, at different temperatures

Directory of Open Access Journals (Sweden)

Hassoune Mohammed

2018-01-01

Full Text Available The inhibition of carbon steel corrosion in neutral sodium chloride solution by N,N'- Dimethylaminoethanol (DMEA, at different temperatures, was investigated using weight loss, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS techniques. The results obtained confirm that DMEA is a good organic corrosion inhibitor for carbon steel in 0.5M of NaCl (concentration encountered in the Mediterranean seawater, over the whole range of temperatures studied. The inhibition efficiency (IE% increases with increasing DMEA concentration; it reaches highest value for a concentration around 0.125 mol.L-1. Potentiodynamic polarization data show that, the compound studied in this research predominantly act as anodic-type inhibitor. The EIS study reveals that the addition of DMEA decreases the corrosion rate of carbon steel in neutral sodium chloride solution, due to the fact that the inhibitor molecules are strongly adsorbed on the active sites following Langmuir isotherm, thus leading to the formation of a stable protective film on the steel surface which is able to keep the metal/solution interface in a passive state. Furthermore, the values of the activation parameters, i.e. ΔHa and Ea obtained in this study indicate that the adsorption process of DMEA is endothermic and could be mainly attributed to chemisorption, respectively.

Influence of sodium chloride, pH, and lactic acid bacteria on anaerobic lactic acid utilization during fermented cucumber spoilage.

Science.gov (United States)

Johanningsmeier, Suzanne D; Franco, Wendy; Perez-Diaz, Ilenys; McFeeters, Roger F

2012-07-01

Cucumbers are preserved commercially by natural fermentations in 5% to 8% sodium chloride (NaCl) brines. Occasionally, fermented cucumbers spoil after the primary fermentation is complete. This spoilage has been characterized by decreases in lactic acid and a rise in brine pH caused by microbial instability. Objectives of this study were to determine the combined effects of NaCl and pH on fermented cucumber spoilage and to determine the ability of lactic acid bacteria (LAB) spoilage isolates to initiate lactic acid degradation in fermented cucumbers. Cucumbers fermented with 0%, 2%, 4%, and 6% NaCl were blended into slurries (FCS) and adjusted to pH 3.2, 3.8, 4.3, and 5.0 prior to centrifugation, sterile-filtration, and inoculation with spoilage organisms. Organic acids and pH were measured initially and after 3 wk, 2, 6, 12, and 18 mo anaerobic incubation at 25 °C. Anaerobic lactic acid degradation occurred in FCS at pH 3.8, 4.3, and 5.0 regardless of NaCl concentration. At pH 3.2, reduced NaCl concentrations resulted in increased susceptibility to spoilage, indicating that the pH limit for lactic acid utilization in reduced NaCl fermented cucumbers is 3.2 or lower. Over 18 mo incubation, only cucumbers fermented with 6% NaCl to pH 3.2 prevented anaerobic lactic acid degradation by spoilage bacteria. Among several LAB species isolated from fermented cucumber spoilage, Lactobacillus buchneri was unique in its ability to metabolize lactic acid in FCS with concurrent increases in acetic acid and 1,2-propanediol. Therefore, L. buchneri may be one of multiple organisms that contribute to development of fermented cucumber spoilage. Microbial spoilage of fermented cucumbers during bulk storage causes economic losses for producers. Current knowledge is insufficient to predict or control these losses. This study demonstrated that in the absence of oxygen, cucumbers fermented with 6% sodium chloride to pH 3.2 were not subject to spoilage. However, lactic acid was degraded

Diferentes níveis de formiato de sódio em substituição ao cloreto de sódio na dieta de frangos de corte - DOI: 10.4025/actascianimsci.v31i3.6020 Diferent levels of sodium formate in replacement of sodium chloride in broiler diets - DOI: 10.4025/actascianimsci.v31i3.6020

Directory of Open Access Journals (Sweden)

Everton Krabbe

2009-09-01

Full Text Available Objetivou-se avaliar a eficácia do formiato de sódio como fonte desse mineral na dieta de frangos de corte, comparando-o com o cloreto de sódio. Utilizaram-se 690 fêmeas de corte Ross, que receberam água e alimentação à vontade, divididas em cinco tratamentos e seis repetições, tendo cada repetição 23 aves. Os tratamentos consistiram: T1 (controle, T2 (formiato de sódio com 0,20% de Na+ com cloreto de amônia, T3 (formiato de sódio com 0,20% de Na+ sem cloreto de amônia, T4 (formiato de sódio com 0,16% de Na+ com cloreto de amônia e T5 (formiato de sódio com 0,12% de Na+ com cloreto de amônia. O cloreto de amônia foi adicionado em alguns tratamentos para se equilibrar o balanço eletrolítico das dietas. Os dados foram analisados, utilizando-se Anova 5%, teste de Tukey com comparação de médias duas a duas. Observou-se que os diferentes níveis de formiato de sódio não comprometeram o desempenho das aves nem as variáveis de carcaça, mesmo quando o cloreto de amônia foi incluído. Com isso, conclui-se que o formiato de sódio pode ser utilizado como fonte desse mineral para substituir o cloreto de sódio em dietas de frangos de corte.This study aimed to evaluate the use of sodium formate as a source of sodium in replacement of sodium chloride for broilers. A total of 690 female Ross broiler chickens were divided into five treatments with 6 replicates each. Each replicate had 23 birds. Treatments consisted of: T1 (control, T2 (sodium formate 0.20%Na+ with ammonium chloride, T3 (sodium formate 0.20%Na+ without ammonium chloride, T4 (sodium formate 0.16%Na+ with ammonium chloride and T5 (sodium formate 0.12%Na+ without ammonium chloride. Ammonium chloride was added to some of the treatments to balance the electrolyte balance of the diets. Data were analyzed using ANOVA 5%. Means were separated using Tukey test.The use of sodium formate had no effect on performance and carcass traits of broilers. These results indicate that

Microscopic diagnosis of sodium acetate-acetic acid-formalin-fixed stool samples for helminths and intestinal protozoa: a comparison among European reference laboratories.

Science.gov (United States)

Utzinger, J; Botero-Kleiven, S; Castelli, F; Chiodini, P L; Edwards, H; Köhler, N; Gulletta, M; Lebbad, M; Manser, M; Matthys, B; N'Goran, E K; Tannich, E; Vounatsou, P; Marti, H

2010-03-01

The present study aimed to compare the diagnostic performance of different European reference laboratories in diagnosing helminths and intestinal protozoa, using an ether-concentration method applied to sodium acetate-acetic acid-formalin (SAF)-preserved faecal samples. In total, 102 stool specimens were analysed during a cross-sectional parasitological survey in urban farming communities in Côte d'Ivoire. Five SAF-preserved faecal samples were prepared from each specimen and forwarded to the participating reference laboratories, processed and examined under a microscope adhering to a standard operating procedure (SOP). Schistosoma mansoni (cumulative prevalence: 51.0%) and hookworm (cumulative prevalence: 39.2%) were the predominant helminths. There was excellent agreement (kappa > 0.8; p protozoa were Entamoeba coli (median prevalence: 67.6%), Blastocystis hominis (median prevalence: 55.9%) and Entamoeba histolytica/Entamoeba dispar (median prevalence: 47.1%). Substantial agreement among reference laboratories was found for E. coli (kappa = 0.69), but only fair or moderate agreement was found for other Entamoeba species, Giardia intestinalis and Chilomastix mesnili. There was only poor agreement for B. hominis, Isospora belli and Trichomonas intestinalis. In conclusion, although common helminths were reliably diagnosed by European reference laboratories, there was only moderate agreement between centres for pathogenic intestinal protozoa. Continued external quality assessment and the establishment of a formal network of reference laboratories is necessary to further enhance both accuracy and uniformity in parasite diagnosis.

Reaction of calcium chloride with alkali metal chlorides in melts

International Nuclear Information System (INIS)

Savin, V.D.; Mikhajlova, N.P.

1984-01-01

Thermochemical characteristics of CaCl 2 reaction with sodium, potassium, rubidium and cesium chlorides in melts at 890 deg C are determined. The values of formation enthalpies of infinitely diluted by CaCl 2 solutions (ΔH) in the chloride row increase from -22 in NaCl to -47 kJ/mol of CaCl 2 in CsCl. With increasing the concentration of calcium chloride in the solution the ΔH values decrease. The regularities of separation from the solution of the CaCl 2 -CsCl system at 890 deg C of the CaCl 2 x CsCl in solid are studied. Formation enthalpies under the given conditions constitutes -70+-3 kJ/mol

Untitled

African Journals Online (AJOL)

degradation of polyanine at positive potentials (ca 0.70 V) vs SCE in the absence of aniline monomer is totally suppressed when the electrochemical process is carried in sodium chloride solution and acetic acid-sodium acetate mixture. INTRODUCTION. Research on conducting polymers i.e., poly-(aniline, pyrrole, ...

Method of processing radioactive metallic sodium with recycling alcohols

International Nuclear Information System (INIS)

Sakai, Takuhiko; Mitsuzuka, Norimasa.

1980-01-01

Purpose: To employ high safety alcohol procession and decrease the amount of wastes in the procession of radioactive metallic sodium discharged from LMFBR type reactors. Method: Radioactive metallic sodium containing long half-decay period nuclides such as cesium, strontium, barium, cerium, lanthanum or zirconium is dissolved in an alcohol at about 70% purity. After extracting the sodium alcoholate thus formed, gaseous hydrochloride is blown-in to separate the sodium alcoholate into alcohol and sodium chloride, and regenerated alcohol is used again for dissolving sodium metal. The sodium chloride thus separated is processed into solid wastes. (Furukawa, Y.)

Norepinephrine-evoked salt-sensitive hypertension requires impaired renal sodium chloride cotransporter activity in Sprague-Dawley rats.

Science.gov (United States)

Walsh, Kathryn R; Kuwabara, Jill T; Shim, Joon W; Wainford, Richard D

2016-01-15

Recent studies have implicated a role of norepinephrine (NE) in the activation of the sodium chloride cotransporter (NCC) to drive the development of salt-sensitive hypertension. However, the interaction between NE and increased salt intake on blood pressure remains to be fully elucidated. This study examined the impact of a continuous NE infusion on sodium homeostasis and blood pressure in conscious Sprague-Dawley rats challenged with a normal (NS; 0.6% NaCl) or high-salt (HS; 8% NaCl) diet for 14 days. Naïve and saline-infused Sprague-Dawley rats remained normotensive when placed on HS and exhibited dietary sodium-evoked suppression of peak natriuresis to hydrochlorothiazide. NE infusion resulted in the development of hypertension, which was exacerbated by HS, demonstrating the development of the salt sensitivity of blood pressure [MAP (mmHg) NE+NS: 151 ± 3 vs. NE+HS: 172 ± 4; P salt-sensitive animals, increased NE prevented dietary sodium-evoked suppression of peak natriuresis to hydrochlorothiazide, suggesting impaired NCC activity contributes to the development of salt sensitivity [peak natriuresis to hydrochlorothiazide (μeq/min) Naïve+NS: 9.4 ± 0.2 vs. Naïve+HS: 7 ± 0.1; P salt-sensitive component of NE-mediated hypertension, while chronic ANG II type 1 receptor antagonism significantly attenuated NE-evoked hypertension without restoring NCC function. These data demonstrate that increased levels of NE prevent dietary sodium-evoked suppression of the NCC, via an ANG II-independent mechanism, to stimulate the development of salt-sensitive hypertension. Copyright © 2016 the American Physiological Society.

Effect of sodium acetate on the volumetric behaviour of some mono-, di-, and tri-saccharides in aqueous solutions over temperature range (288.15 to 318.15) K

Energy Technology Data Exchange (ETDEWEB)

Banipal, Parampaul K., E-mail: pkbanipal@yahoo.co [Department of Chemistry, Guru Nanak Dev University, Amritsar 143 005 (India); Singh, Vickramjeet [Department of Chemistry, Guru Nanak Dev University, Amritsar 143 005 (India); Banipal, Tarlok S. [Department of Applied Chemistry, Guru Nanak Dev University, Amritsar 143 005 (India)

2010-01-15

The standard partial molar volumes, V{sub 2}{sup 0} at infinite dilution of eight monosaccharides [D(+)-xylose, D(-)-arabinose, D(-)-ribose, L(-)-sorbose, D(-)-fructose, D(+)-galactose, D(+)-glucose, and D(+)-mannose], six disaccharides [D(+)-cellobiose, sucrose, D(+)-melibiose, D(+)-lactose monohydrate, D(+)-trehalose dihydrate, and D(+)-maltose monohydrate] and two trisaccharides [D(+)-melizitose and D(+)-raffinose pentahydrate] (molalities of saccharides range from (0.03 to 0.12) mol . kg{sup -1}) have been determined in water and in (0.5, 1.0, 2.0, and 3.0) mol . kg{sup -1} aqueous sodium acetate solutions at temperatures, T = (288.15, 298.15, 308.15, and 318.15) K from density measurements using a vibrating-tube digital densimeter. From these results, corresponding standard partial molar volumes of transfer, DELTA{sub t}V{sub 2}{sup 0} have been determined for the transfer of various saccharides from water to aqueous solutions of sodium acetate. Positive values of DELTA{sub t}V{sub 2}{sup 0} were obtained for most of the saccharides, whose magnitude increase with the concentration of sodium acetate as well as temperature. However, negative DELTA{sub t}V{sub 2}{sup 0} values were observed for L(-)-sorbose, D(-)-fructose and D(+)-xylose at lower concentrations of co-solute. The negative magnitude of DELTA{sub t}V{sub 2}{sup 0} values decrease with rise of temperature from (288.15 to 318.15) K. Pair and higher order volumetric interaction coefficients have been determined by using McMillan-Mayer theory. Partial molar expansion coefficients, (partial derivV{sub 2}{sup 0}/partial derivT){sub p} and the second derivatives (partial deriv{sup 2}V{sub 2}{sup 0}/partial derivT{sup 2}){sub p} have also been estimated. These parameters have been utilized to understand various mixing effects in aqueous solutions due to the interactions between solute (saccharide) and co-solute (sodium acetate).

Design, Characterization, and Optimization of Controlled Drug Delivery System Containing Antibiotic Drug/s

Directory of Open Access Journals (Sweden)

Apurv Patel

2016-01-01

Full Text Available The objective of this work was design, characterization, and optimization of controlled drug delivery system containing antibiotic drug/s. Osmotic drug delivery system was chosen as controlled drug delivery system. The porous osmotic pump tablets were designed using Plackett-Burman and Box-Behnken factorial design to find out the best formulation. For screening of three categories of polymers, six independent variables were chosen for Plackett-Burman design. Osmotic agent sodium chloride and microcrystalline cellulose, pore forming agent sodium lauryl sulphate and sucrose, and coating agent ethyl cellulose and cellulose acetate were chosen as independent variables. Optimization of osmotic tablets was done by Box-Behnken design by selecting three independent variables. Osmotic agent sodium chloride, pore forming agent sodium lauryl sulphate, and coating agent cellulose acetate were chosen as independent variables. The result of Plackett-Burman and Box-Behnken design and ANOVA studies revealed that osmotic agent and pore former had significant effect on the drug release up to 12 hr. The observed independent variables were found to be very close to predicted values of most satisfactory formulation which demonstrates the feasibility of the optimization procedure in successful development of porous osmotic pump tablets containing antibiotic drug/s by using sodium chloride, sodium lauryl sulphate, and cellulose acetate as key excipients.

Alkali metal and ammonium chlorides in water and heavy water (binary systems)

CERN Document Server

Cohen-Adad, R

1991-01-01

This volume surveys the data available in the literature for solid-fluid solubility equilibria plus selected solid-liquid-vapour equilibria, for binary systems containing alkali and ammonium chlorides in water or heavy water. Solubilities covered are lithium chloride, sodium chloride, potassium chloride, rubidium chloride, caesium chloride and ammonium chloride in water and heavy water.

Investigations of the corrosion behaviour of special heat exchanging materials in sodium acetate trihydrate melt for the application latent heat storage; Untersuchungen des Korrosionsverhaltens ausgewaehlter Waermeaustauscherwerkstoffe in Natriumacetat-Trihydrat-Schmelze fuer den Anwendungsfall Latentwaermespeichersysteme

Energy Technology Data Exchange (ETDEWEB)

Brandt, B.; Stimming, U. [ZAE Bayern, Walter-Meissner-Str. 6, 87748 Garching (Germany)

2004-06-01

The development activities in the area of latent heat storage have more and more increased in the last years. The reason is the search for new energy storage systems of higher energy efficiency and the reinforced utilisation of renewable and alternative energies which are often only irregularly available. The special advantage of latent heat storage is the high energy storage density which could be reached at the melting point of selected storage materials and the resulting reduction of required space respectively the nearly constant temperature. An important topic relating to the development of these storage systems was the investigation of the long time stability, especially the corrosion stability. At the same time the heat exchange material has the function to transfer the heat and coldness from a heat transfer medium, e. g. water which has drawn the energy from an external source to the storage material. Among the storage materials the sodium acetate trihydrate (melting point: 58 C) has interesting advantages. In that reason the investigation of the corrosion behaviour and the choose of suitable materials for heat exchangers was an important goal. In the present report important results of the investigation of selected metals at 80 C in sodium acetate trihydrate are described. The corrosion influencing impurities chloride, sulphate and carbonate which could be contained in the much more inexpensive salt hydrate of technical quality were added to the analytically pure sodium acetate trihydrate. Furthermore the addition of graphite (for increasing the heat conductivity) and the contact with air were investigated. Some promising metals of high corrosion resistance are the result of the investigations. (Abstract Copyright [2004], Wiley Periodicals, Inc.) [German] In den letzten Jahren haben sich die Entwicklungsaktivitaeten auf dem Gebiet der Latentwaermespeicherung erheblich verstaerkt. Grund dafuer ist die Suche nach Energiespeichern mit hoeherer Effizienz und

Effect of sodium chloride on photosynthetic 14CO2 assimilation in Portulaca oleracea Linn

International Nuclear Information System (INIS)

Joshi, G.V.; Karadge, B.A.

1979-01-01

Effect of NaCl on ion uptake, photosynthetic rate and photosynthetic products in a C 4 non-CAM succulent, P. oleracea has been investigated. NaCl causes accumulation of Na as well as Cl ions with decrease in K and Ca contents. Chlorophylls and photosynthetic 14 CO 2 fixation rates are adversely affected due to sodium chloride salinity. Plants grown in the presence of NaCl show increase in C 4 acid percentage with increase in labelling of organic acids in light. Labelling of amino acids (particularly alanine) and sugars (sucrose) is affected by NaCl. Enzyme studies reveal that PEP-carboxylase is stimulated at all concentrations of NaCl but higher concentrations affected the activity of RuBP-Carboxylase. (author)

Development of an automated modular system for the synthesis of [11C]acetate.

Science.gov (United States)

Felicini, Chiara; Någren, Kjell; Berton, Andrea; Pascali, Giancarlo; Salvadori, Piero Alberto

2010-12-01

Carboxylation reactions offer a straightforward method for the synthesis of carbon-11 labelled carboxylic acids. Among these, the preparation of carbon-11 (C)-acetate is receiving increasing attention because of diagnostic applications in oncology in addition to its well-established use as a probe for myocardial oxidative metabolism. Although a number of dedicated modules are commercially available, the development of the synthesis on flexible platforms would be beneficial to widen the number of tracers, in particular for preclinical assessment and testing. In this study, the carboxylation reaction was implemented for the synthesis of sodium 1-[C]acetate after the classic route of carboxylation of methylmagnesium chloride by [C]carbon dioxide, followed by the acidic hydrolysis, purification and sterile filtration. This was performed using a commercially available kit of preassembled hardware units and fully compatible components of radiochemistry automation (VarioSystem). The system proved be to highly versatile and inexpensive and allowed a quick translation of the radiochemistry project into a working system even by less experienced personnel, because of predefined interfaces between electronic parts and operating software (preloaded on a laptop and included in the kit). The automatic module proved to be a simple and reliable system for the production of 1-[C]acetate that was prepared in 24 min (total synthesis time) with stable radiochemical yields (20% nondecay corrected) and high radiochemical purity (>97%). The module is used routinely to produce 1-[C]acetate for preclinical studies and is being implemented for the production of the labelled fatty acids.

The effective reaction of 2-chloro-3-formylquinoline and acetic acid ...

African Journals Online (AJOL)

formylquinolines in a single step by treating with sodium acetate and acetic acid under microwave irradiation. The structures of the compounds have been established by IR, NMR and mass spectral data. Unexpectedly ...

Direct versus indirect electrochemical oxidation of pesticide polluted drainage water containing sodium chloride

DEFF Research Database (Denmark)

Muff, Jens; Erichsen, Rasmus; Damgaard, Christian

2008-01-01

Drainage water from a depot of chemical waste, polluted with a mixture of organophosphates and degradation products was treated by a direct as well as an indirect electrochemical method using a Ti/Pt-Ir anode and Stainless Steel 304 cathode. With a concentration of 0.7%, sodium chloride...... the treatment. Indirect electrochemical treatment, where a highly oxidized brine solution was added to the drainage water, revealed immediately reduction in COD, and similar to the direct treatment, degradation of all of the pesticide pollutants was obtained except for the O,O,O-triethyl-phosphoric acid...... concentrations. Analyses of the actual pollutants, Me-Parathion, parathion, malathion and degradation products, confirmed that the concentrations of all initial pollutants were eliminated during the treatment. The only exception was O,O,O-triethyl-phosphoric acid, a degradation product which was formed during...

Direct versus indirect electrochemical oxidation of pesticide polluted drainage water containing sodium chloride

DEFF Research Database (Denmark)

Muff, Jens; Erichsen, Rasmus; Damgaard, Christian

2008-01-01

the treatment. Indirect electrochemical treatment, where a highly oxidized brine solution was added to the drainage water, revealed immediately reduction in COD, and similar to the direct treatment, degradation of all of the pesticide pollutants was obtained except for the O,O,O-triethyl-phosphoric acid......Drainage water from a depot of chemical waste, polluted with a mixture of organophosphates and degradation products was treated by a direct as well as an indirect electrochemical method using a Ti/Pt-Ir anode and Stainless Steel 304 cathode. With a concentration of 0.7%, sodium chloride...... concentrations. Analyses of the actual pollutants, Me-Parathion, parathion, malathion and degradation products, confirmed that the concentrations of all initial pollutants were eliminated during the treatment. The only exception was O,O,O-triethyl-phosphoric acid, a degradation product which was formed during...

Effects of 12-O-tetradecanoyl-phorbol-13-acetate [corrected] and sodium lauryl sulfate on the production and expression of cytokines and proto-oncogenes in photoaged and intrinsically aged human keratinocytes.

Science.gov (United States)

Suh, D H; Youn, J I; Eun, H C

2001-11-01

Skin aging may be divided into photoaging and intrinsic aging. The purpose of this study was to investigate the effects of 12-O-tetradecanoyl-phorbol-13-acetate and sodium lauryl sulfate on the production and expression of cytokines and proto-oncogenes in photoaged and intrinsically aged skin, compared with young skin. Keratinocytes were taken from newborns, young adults in their twenties, and from the forearm and thigh of volunteers in their fifties and seventies. Interleukin-1alpha and -6, and interleukin-1 receptor antagonist, c-fos and c-myc were measured after cultured keratinocytes had been treated with 12-O-tetradecanoyl-phorbol-13-acetate and sodium lauryl sulfate. There has been no report concerning the dependence of cytokine production by sodium lauryl sulfate upon photoaging and intrinsic aging. This study also involves the first investigation of the effects of aging on c-myc expression by 12-O-tetradecanoyl-phorbol-13-acetate treatment. Cytokine production decreased markedly with age. These results suggest the progressive decline of cellular function with age. The ratio of cytokine production in the irritant-treated group compared with that in the control group showed a different pattern in photoaging and intrinsic aging. With the significant difference between photoaging and intrinsic aging, T/C ratio decreased in interleukin-1alpha and interleukin-1 receptor antagonist upon aging, whereas it increased in interleukin-6. S/C ratio was uniquely elevated on photoaged skin in the 50 y age group. It is suggested that photoaged skin shows an exaggerated reaction to surfactant. Compared with the control, c-fos expression in 12-O-tetradecanoyl-phorbol-13-acetate-treated keratinocytes decreased with age in the thigh, but increased in the photoaged skin of forearm. The increased c-fos expression in 12-O-tetradecanoyl-phorbol-13-acetate-treated keratinocytes could be relevant for the predisposition of photoaged keratinocytes to malignant transformation.

Effects of eslicarbazepine acetate on lipid profile and sodium levels in patients with epilepsy.

Science.gov (United States)

Pulitano, Patrizia; Franco, Valentina; Mecarelli, Oriano; Brienza, Marianna; Davassi, Chiara; Russo, Emilio

2017-12-01

Several studies have demonstrated that treatment with enzyme-inducing antiepileptic drugs is associated with increased serum lipid levels. Eslicarbazepine acetate (ESL) is a novel antiepileptic drug specifically designed with the objective to identify carbamazepine and oxcarbazepine analogues with favorable pharmacodynamic and pharmacokinetic profiles. The present study aimed to assess the changes in lipid profile and sodium levels in patients with epilepsy taking ESL as adjunctive therapy. This report describes a retrospective cohort study of 36 adult patients with epilepsy, taking ESL as an add-on treatment. The laboratory values assessed prior and after (range 6-18 months) ESL treatment were sodium levels, total cholesterol (TC), low (LDL) and high (HDL) density lipoproteins and triglycerides. TC and LDL values were significantly decreased already after at least six months of therapy with ESL (191.3±29.6 vs 179.7±29.2mg/dl, p ESL treatment were significantly increased (57.5± 9.1 vs 63.9±8.3mg/dl; pESL, in contrast to the negative effects observed with traditional older carboxamides, positively affects lipid metabolism profile in patients with epilepsy over an average follow-up of 11 months. Further research is needed to confirm the obtained results with a focus on a comprehensive assessment of the biochemical and molecular mechanisms involved. Copyright © 2017 British Epilepsy Association. Published by Elsevier Ltd. All rights reserved.

40 CFR 721.2076 - D-Glucuronic acid, polymer with 6-deoxy-L-mannose and D-glucose, acetate, calcium magnesium...

Science.gov (United States)

2010-07-01

...-deoxy-L-mannose and D-glucose, acetate, calcium magnesium potassium sodium salt. 721.2076 Section 721...-Glucuronic acid, polymer with 6-deoxy-L-mannose and D-glucose, acetate, calcium magnesium potassium sodium... identified as D-Glucuronic acid, polymer with 6-deoxy-L-mannose and D-glucose, acetate, calcium magnesium...

Stability of tacrolimus injection diluted in 0.9% sodium chloride injection and stored in Excel bags.

Science.gov (United States)

Myers, Alan L; Zhang, Yanping; Kawedia, Jitesh D; Shank, Brandon R; Deaver, Melissa A; Kramer, Mark A

2016-12-15

The chemical stability and physical compatibility of tacrolimus i.v. infusion solutions prepared in Excel bags and stored at 23 or 4 °C for up to nine days were studied. Tacrolimus admixtures (2, 4, and 8 μg/mL) were prepared in Excel bags using 0.9% sodium chloride injection and stored at 23 °C without protection from light or at 4 °C in the dark. Test samples were withdrawn from triplicate bag solutions immediately after preparation and at predetermined time intervals (1, 3, 5, 7, and 9 days). Chemical stability was assessed by measuring tacrolimus concentrations using a validated stability-indicating high-performance liquid chromatography assay. The physical stability of the admixtures was assessed by visual examination and by measuring turbidity, particle size, and drug content. All test solutions stored at 23 or 4 °C had a no greater than 6% loss of the initial tacrolimus concentration throughout the nine-day study period. All test samples of tacrolimus admixtures, under both storage conditions, were without precipitation and remained clear initially and throughout the nine-day observation period. Changes in turbidities were minor; measured particulates remained few in number in all samples throughout the study. Extemporaneously prepared infusion solutions of tacrolimus 2, 4, and 8 μg/mL in 0.9% sodium chloride injection in Excel bags were chemically and physically stable for at least nine days when stored at room temperature (23 °C) without protection from light and when stored in a refrigerator (4 °C) in the dark. Copyright © 2016 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

Synthesis of 14C-dehydrocorydaline chloride

International Nuclear Information System (INIS)

Zhang Rui; Wang Ding

1988-01-01

A method for synthesis of 14 C-dehydrocorydaline chloride is described. In the presence of sodium hydroxide, acetonylpalmatine is reacted with 14 C-methyl iodide in sealed glass ampoule to give 14 C-13-methylpalmatine iodide which is then converted to chloride. The radiochemical purity of 14 C-dehydrocorydaline determined by TLC is over 98% and the labelling efficiency is 54%

Lactated Ringer's solution or 0.9% sodium chloride as fluid therapy in pigeons (Columba livia submitted to humerus osteosynthesis

Directory of Open Access Journals (Sweden)

Adriano B. Carregaro

2015-01-01

Full Text Available The study aimed to compare the effects of intraosseous infusion of lactated Ringer's and 0.9% sodium chloride solutions on the electrolytes and acid-base balance in pigeons submitted to humerus osteosynthesis. Eighteen pigeons were undergoing to isoflurane anesthesia by an avalvular circuit system. They were randomly assigned into two groups (n=9 receiving lactated Ringer's solution (LR or 0.9% sodium chloride (SC, in a continuous infusion rate of 20mL/kg/h, by using an intraosseous catheter into the tibiotarsus during 60-minute anesthetic procedure. Heart rate (HR, and respiratory rate (RR were measured every 10 min. Venous blood samples were collected at 0, 30 and 60 minutes to analyze blood pH, PvCO2, HCO3 -, Na+ and K+. Blood gases and electrolytes showed respiratory acidosis in both groups during induction, under physical restraint. This acidosis was evidenced by a decrease of pH since 0 min, associated with a compensatory response, observed by increasing of HCO3 - concentration, at 30 and 60 min. It was not observed any changes on Na+ and K+ serum concentrations. According to the results, there is no reason for choosing one of the two solutions, and it could be concluded that both fluid therapy solutions do not promote any impact on acid-base balance and electrolyte concentrations in pigeons submitted to humerus osteosynthesis.

Corrosion performance of SiCsubp/6061 Al metal matrix composites in sodium chloride solution

International Nuclear Information System (INIS)

Mohmad Soib bin Selamat

1995-01-01

The corrosion performance of silicon carbide particle/aluminium metal matrix composites (SiCsubp/Al) were studied in sodium chloride solution by means of electrochemical, microscopic, gravimetric and analytical techniques. The materials under investigation were compocasting processed 6061 Al reinforced with increasing amounts of SiC particles. Potentiostatic polarization tests were done in 0.1M NaCl solutions that were aerated or deaerated to observe overall corrosion behaviour. It was seen that the corrosion potentials did not vary greatly in relation to the amounts of SiCsubp reinforcement. Corrosion tests showed that the degree of corrosion increased with increasing SiCsubp content. SEM analysis technique was used to study the corroded samples and the pitting morphology. By TEM, no intermetallic layer was found at SiC/Al interface. A model for pitting process was proposed

Measurement of the body content of sodium, potassium, chloride, calcium, phophorus and nitrogen with reference to spironolactone

International Nuclear Information System (INIS)

Boddy, K.

1978-01-01

The total body content of sodium, chloride, nitrogen, calcium and phosphorus can be measured simultaneously by in vivo activation analysis and at the same time total body potassium can be determined directly by whole body counting. These procedures have been described and compared with methods using isotope dilution. The complementary nature of the techniques, when properly applied, as well as reported disparities have been illustrated by a number of clinical investigations generally involving aldosterone antagonists. The methods should provide a better insight to the complex changes in body conposition and metabolism accociated with hypertension (and other diseases) and their treatment. (Auth.)

Effects of Different Oral Doses of Sodium Chloride on the Basal Acid-Base and Mineral Status of Exercising Horses Fed Low Amounts of Hay.

Science.gov (United States)

Zeyner, Annette; Romanowski, Kristin; Vernunft, Andreas; Harris, Patricia; Müller, Ann-Marie; Wolf, Carola; Kienzle, Ellen

2017-01-01

The provision of NaCl, according to current recommendations, to horses in moderate work has been shown to induce immediate postprandial acidosis. The present study aimed to clarify whether this NaCl induced acidosis i) persists beyond the immediate postprandial period, and ii) is still present after a 2 week adaptation period. Six adult warmblood mares in moderate work received daily 1.00 kg hay per 100 kg body weight (bwt) only together with 0.64 kg unprocessed cereal grains/100 kg bwt.d as fed basis. Using a 3x3 Latin Square, either 0 (NaCl-0), 50 (NaCl-50) or 100 (NaCl-100) g NaCl/d were fed together with the concentrates in two equal doses for 3 weeks. During the final week, a mineral digestibility trial was undertaken. The middle sodium and chloride intake (NaCl-50) at least met the most common recommendations for moderate work. Morning (7:00 AM) urine and venous blood samples were collected on days 0, 1-4, 8, and 15, and analysed for pH, acid-base status, creatinine and electrolyte concentrations. Fractional electrolyte clearances (FC) were determined. Mean apparent sodium digestibility ranged between 60-62% whereas chloride digestibility was consistently above 94%. Supplementing 100 g but not 50 g of NaCl resulted in significant reduction of blood pH and base excess as well as urinary pH and urine acid excretion. Both 50 g and 100 g NaCl supplementation caused a significant reduction in base and net acid-base excretion, urine density and potassium concentration, but increased urine sodium concentration and the FC of sodium and chloride (P salt doses is excreted renally. The above effects of NaCl supplementation persisted over the 2 week measurement period. Results suggest that feeding 100 g NaCl to moderately exercising horses results in mild metabolic acidosis, whereas feeding 50 g according to current recommendations resulted in compensated acidosis.

Effects of Different Oral Doses of Sodium Chloride on the Basal Acid-Base and Mineral Status of Exercising Horses Fed Low Amounts of Hay.

Directory of Open Access Journals (Sweden)

Annette Zeyner

Full Text Available The provision of NaCl, according to current recommendations, to horses in moderate work has been shown to induce immediate postprandial acidosis. The present study aimed to clarify whether this NaCl induced acidosis i persists beyond the immediate postprandial period, and ii is still present after a 2 week adaptation period. Six adult warmblood mares in moderate work received daily 1.00 kg hay per 100 kg body weight (bwt only together with 0.64 kg unprocessed cereal grains/100 kg bwt.d as fed basis. Using a 3x3 Latin Square, either 0 (NaCl-0, 50 (NaCl-50 or 100 (NaCl-100 g NaCl/d were fed together with the concentrates in two equal doses for 3 weeks. During the final week, a mineral digestibility trial was undertaken. The middle sodium and chloride intake (NaCl-50 at least met the most common recommendations for moderate work. Morning (7:00 AM urine and venous blood samples were collected on days 0, 1-4, 8, and 15, and analysed for pH, acid-base status, creatinine and electrolyte concentrations. Fractional electrolyte clearances (FC were determined. Mean apparent sodium digestibility ranged between 60-62% whereas chloride digestibility was consistently above 94%. Supplementing 100 g but not 50 g of NaCl resulted in significant reduction of blood pH and base excess as well as urinary pH and urine acid excretion. Both 50 g and 100 g NaCl supplementation caused a significant reduction in base and net acid-base excretion, urine density and potassium concentration, but increased urine sodium concentration and the FC of sodium and chloride (P < 0.05. This suggests that a high proportion of the recommended salt doses is excreted renally. The above effects of NaCl supplementation persisted over the 2 week measurement period. Results suggest that feeding 100 g NaCl to moderately exercising horses results in mild metabolic acidosis, whereas feeding 50 g according to current recommendations resulted in compensated acidosis.

The crystal structure of the regulatory domain of the human sodium-driven chloride/bicarbonate exchanger.

Science.gov (United States)

Alvadia, Carolina M; Sommer, Theis; Bjerregaard-Andersen, Kaare; Damkier, Helle Hasager; Montrasio, Michele; Aalkjaer, Christian; Morth, J Preben

2017-09-21

The sodium-driven chloride/bicarbonate exchanger (NDCBE) is essential for maintaining homeostatic pH in neurons. The crystal structure at 2.8 Å resolution of the regulatory N-terminal domain of human NDCBE represents the first crystal structure of an electroneutral sodium-bicarbonate cotransporter. The crystal structure forms an equivalent dimeric interface as observed for the cytoplasmic domain of Band 3, and thus establishes that the consensus motif VTVLP is the key minimal dimerization motif. The VTVLP motif is highly conserved and likely to be the physiologically relevant interface for all other members of the SLC4 family. A novel conserved Zn 2+ -binding motif present in the N-terminal domain of NDCBE is identified and characterized in vitro. Cellular studies confirm the Zn 2+ dependent transport of two electroneutral bicarbonate transporters, NCBE and NBCn1. The Zn 2+ site is mapped to a cluster of histidines close to the conserved ETARWLKFEE motif and likely plays a role in the regulation of this important motif. The combined structural and bioinformatics analysis provides a model that predicts with additional confidence the physiologically relevant interface between the cytoplasmic domain and the transmembrane domain.

Potentiometric Determination of Free Chloride in Cement Paste – an ...

African Journals Online (AJOL)

... cement paste.16 The accuracy and reliability of this analytical technique has been checked against a certified reference material, Merck sodium chloride solution. Confidence levels (CL0.95), of 0.03 and relative standard deviations of 0.2 % for chloride were determined for ordinary Portland cement (OPC) chloride binding ...

Standard practice for exposure of metals and alloys by alternate immersion in neutral 3.5% Sodium Chloride solution

CERN Document Server

American Society for Testing and Materials. Philadelphia

1999-01-01

1.1 This practice covers procedures for making alternate immersion stress corrosion tests in 3.5 % sodium chloride (NaCl) (). It is primarily for tests of aluminum alloys (Test Method G 47) and ferrous alloys, but may be used for other metals exhibiting susceptibility to chloride ions. It sets forth the environmental conditions of the test and the means for controlling them. Note 1 Alternate immersion stress corrosion exposures are sometimes made in substitute ocean water (without heavy metals) prepared in accordance with Specification D 1141. The general requirements of this present practice are also applicable to such exposures except that the reagents used, the solution concentration, and the solution pH should be as specified in Specification D 1141. 1.2 This practice can be used for both stressed and unstressed corrosion specimens. Historically, it has been used for stress-corrosion cracking testing, but is often used for other forms of corrosion, such as uniform, pitting, intergranular, and galvanic. ...

Characterization and reactivity of sodium aluminoborosilicate glass fiber surfaces

Energy Technology Data Exchange (ETDEWEB)

Ortiz Rivera, Lymaris, E-mail: luo105@psu.edu [Materials Research Institute, Pennsylvania State University, University Park, PA 16802 (United States); Bakaev, Victor A.; Banerjee, Joy [Materials Research Institute, Pennsylvania State University, University Park, PA 16802 (United States); Mueller, Karl T. [Department of Chemistry, Pennsylvania State University, University Park, PA 16802 (United States); Pantano, Carlo G. [Materials Research Institute, Pennsylvania State University, University Park, PA 16802 (United States); Department of Materials Science and Engineering, Pennsylvania State University, University Park, PA 16802 (United States)

2016-05-01

Highlights: • XPS revealed that these fiber surfaces contain sodium carbonate weathering products. • IGC–MS data confirms the products of acetic acid reaction with sodium carbonate. • NMR data shows two closely spaced, but distinct sodium carboxylate peaks. • Acetic acid reacts with both sodium in the glass and sodium in the sodium carbonate. - Abstract: Multicomponent complex oxides, such as sodium aluminoborosilicate glass fibers, are important materials used for thermal insulation in buildings and homes. Although the surface properties of single oxides, such as silica, have been extensively studied, less is known about the distribution of reactive sites at the surface of multicomponent oxides. Here, we investigated the reactivity of sodium aluminoborosilicate glass fiber surfaces for better understanding of their interface chemistry and bonding with acrylic polymers. Acetic acid (with and without a {sup 13}C enrichment) was used as a probe representative of the carboxylic functional groups in many acrylic polymers and adhesives. Inverse gas chromatography coupled to a mass spectrometer (IGC–MS), and solid state nuclear magnetic resonance (NMR), were used to characterize the fiber surface reactions and surface chemical structure. In this way, we discovered that both sodium ions in the glass surface, as well as sodium carbonate salts that formed on the surface due to the intrinsic reactivity of this glass in humid air, are primary sites of interaction with the carboxylic acid. Surface analysis by X-ray photoelectron spectroscopy (XPS) confirmed the presence of sodium carbonates on these surfaces. Computer simulations of the interactions between the reactive sites on the glass fiber surface with acetic acid were performed to evaluate energetically favorable reactions. The adsorption reactions with sodium in the glass structure provide adhesive bonding sites, whereas the reaction with the sodium carbonate consumes the acid to form sodium-carboxylate, H

Sodium Carbonate is Saltier Than Sodium Chloride to Sodium-Depleted Rats.

Science.gov (United States)

St John, Steven J; McBrayer, Anya M; Krauskopf, Erin E

2017-10-01

In a series of behavioral experiments in the 1960s, G.R. Morrison identified several unique features of the taste of Na2CO3 to rats; namely, it is 1) considerably more intense than NaCl at isomolar concentrations, 2) avoided at 10 times lower concentrations than NaCl to thirsty rats, 3) preferred at 10 times lower concentrations than NaCl in sodium-depleted rats. He also demonstrated its qualitatively similarity to NaCl. In Experiment 1, we confirmed and extended many of Morrison's observations. Rats were injected with furosemide on 3 occasions to stimulate a sodium appetite. After each depletion, rats were given a brief-access taste test in a lickometer presenting, in random order, water and 7 concentrations of salt. One test used NaCl (0.028-0.89 M, quarter log steps), another used Na2CO3, and the third used Na2CO3, but at a tenfold lower concentration range (0.0028-0.089 M). Rats licked NaCl in an inverted-U shaped concentration-response function peaking at 0.158-0.281 M. As Morrison's results predicted, rats licked Na2CO3 in nearly identical fashion, but at a tenfold lower concentration range (peak at 0.0158-0.028 M). In a second experiment, furosemide-treated rats were repeatedly tested with the lower Na2CO3 range but mixed in the epithelial sodium channel blocker amiloride at various concentrations (3-300 μM, half log steps). Amiloride reduced licking for Na2CO3 and shifted the peak response rightward up to about half a log unit. Thus, this "super-saltiness" of Na2CO3 to rats is at least partly amiloride-dependent. © The Author 2017. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Enhanced dispersion stability and mobility of carboxyl-functionalized carbon nanotubes in aqueous solutions through strong hydrogen bonds

International Nuclear Information System (INIS)

Bahk, Yeon Kyoung; He, Xu; Gitsis, Emmanouil; Kuo, Yu-Ying; Kim, Nayoung; Wang, Jing

2015-01-01

Dispersion of carbon nanotubes has been heavily studied due to its importance for their technical applications, toxic effects, and environmental impacts. Common electrolytes, such as sodium chloride and potassium chloride, promote agglomeration of nanoparticles in aqueous solutions. On the contrary, we discovered that acetic electrolytes enhanced the dispersion of multi-walled carbon nanotubes (MWCNTs) with carboxyl functional group through the strong hydrogen bond, which was confirmed by UV–Vis spectrometry, dispersion observations and aerosolization-quantification method. When concentrations of acetate electrolytes such as ammonium acetate (CH 3 CO 2 NH 4 ) and sodium acetate (CH 3 CO 2 Na) were lower than 0.03 mol per liter, MWCNT suspensions showed better dispersion and had higher mobility in porous media. The effects by the acetic environment are also applicable to other nanoparticles with the carboxyl functional group, which was demonstrated with polystyrene latex particles as an example

Extraction of heavy metals from MSWI fly ash using hydrochloric acid and sodium chloride solution.

Science.gov (United States)

Weibel, Gisela; Eggenberger, Urs; Kulik, Dmitrii A; Hummel, Wolfgang; Schlumberger, Stefan; Klink, Waldemar; Fisch, Martin; Mäder, Urs K

2018-03-17

Fly ash from municipal solid waste incineration contains a large potential for recyclable metals such as Zn, Pb, Cu and Cd. The Swiss Waste Ordinance prescribes the treatment of fly ash and recovery of metals to be implemented by 2021. More than 60% of the fly ash in Switzerland is acid leached according to the FLUWA process, which provides the basis for metal recovery. The investigation and optimization of the FLUWA process is of increasing interest and an industrial solution for direct metal recovery within Switzerland is in development. With this work, a detailed laboratory study on different filter cakes from fly ash leaching using HCl 5% (represents the FLUWA process) and concentrated sodium chloride solution (300 g/L) is described. This two-step leaching of fly ash is an efficient combination for the mobilization of a high percentage of heavy metals from fly ash (Pb, Cd ≥ 90% and Cu, Zn 70-80%). The depletion of these metals is mainly due to a combination of redox reaction and metal-chloride-complex formation. The results indicate a way forward for an improved metal depletion and recovery from fly ash that has potential for application at industrial scale. Copyright © 2018 Elsevier Ltd. All rights reserved.

Interaction of calcium oxide with molten alkali metal chlorides

International Nuclear Information System (INIS)

Volkovich, A.V.; Zhuravlev, V.I.; Ermakov, D.S.; Magurina, M.V.

1999-01-01

Calcium oxide solubility in molten lithium, sodium, potassium, cesium chlorides and their binary mixtures is determined in a temperature range of 973-1173 K by the method of isothermal saturation. Mechanisms of calcium oxide interaction with molten alkali metal chlorides are proposed

Synergism between sodium chloride, sucrose and tricalcium phosphate in the osmotic dehydration of oca (Oxalis tuberosa with and without chitosan coating

Directory of Open Access Journals (Sweden)

José Arroyo Portal

2010-12-01

Full Text Available We investigated the synergistic effect of three solutes (sodium chloride, sucrose, tricalcium phosphate in different combinations of concentration, on the moisture, solid gain and calcium gain in oca (Oxalis tuberosa with and without chitosan (CR and SR. In both cases applied the Simplex with Extended Centroid mixture design. Were used cylinders of oca of 0.9 cm of diameter and 3.4 cm of length. The kinetics of moisture, solid gain and calcium gain for 48 hours was evaluated. The effective diffusivity of water, solids and calcium was determined. We found that in samples CR is greater loss of water and less solid gain compared with SR samples mainly as sodium chloride or sucrose participate independently, while for the gain of calcium, in all cases, the CR samples gain more of calcium than SR samples. The effective diffusivities found are: water, 1.19E-09 m2 /s in samples CR and 1.34E-09 m2 /s in SR samples; for solid, 3.67E-09 m2 /s in samples CR and 5.43E-09 m2 /s in SR samples; and, for calcium 3.32E-11 m2 /s in samples CR and 1.57E-09 m2 /s in SR samples.

Impact of stirring speed, glycerin and sodium chloride concentrations on photoprotective nanoemulsions

Directory of Open Access Journals (Sweden)

Débora Granemann e Silva

2014-09-01

Full Text Available New technologies that improve the physical as the sensory properties of sunscreens can help to increase its continued use and impact on health. The use of nanoemulsions in the development of photoprotective vehicles is an advantage, since nanostructured components may have superior properties regarding their performance when compared to conventional products. The advantages of using nanobiotechnology in manufacture of cosmetic and dermatological formulations arise from the protection of compounds from chemical or enzymatic degradation, from the control of their release, and also to the prolonged retention time of cosmetic ingredients in the stratum corneum. Thus, this study aimed to evaluate the impact of stirring speed and of glycerin and sodium chloride concentrations in the development and effectiveness of a nanoemulsion containing ethylhexyl methoxycinnamate and benzophenone-3. The results of statistical analyses regarding the impact of the variables in the process of nanoemulsion development showed that these parameters affect the phase inversion temperature (PIT. However, this did not affect the particle size and the photoprotective efficacy in vitro.

effect of ascorbic acid and/or sodium chloride on irradiated mungbean seeds

International Nuclear Information System (INIS)

Hussein, O.S.

2010-01-01

dry seeds of mungbean (Vigna radiata L.) were irradiated with different doses of gamma rays (0, 50, 100, 250 Gy) dose rate was 1.33 Gy/sec and germinated under laboratory conditions (28 degree C±2 degree C) in 100 mM of sodium chloride or 10 mM ascorbic acid or mixture of both in equal amounts . a group of irradiated and unirradiated seeds were moistened with tap water and considered as control. the growth parameters of two weeks old seedling were recorded. photosynthetic pigments, total carbohydrates, crud protein and amino acids contents were also determined. gamma radiation (50-100 Gy)increased total chlorophylls and carotenoid pigments while the highest dose of irradiation (250 Gy) reduced these contents. saline condition decreased total chlorophyll and carotenoid contents of seedlings resulted from irradiated seeds than control. adding of ascorbic acid to irradiated mungbean seeds in presence of NaCl overcame partially the inhibitory effect of NaCl on chlorophyll and carotenoid contents of seedlings. the pattern of changes in amino acids content was more or less similar to that of photosynthetic pigments.

EPR study of sodium plutonyl acetate NaPuO2(CH3COO)3 and plutonium thenoyl trifluoroacetonate Pu(TTA)4: self-irradiation effects

International Nuclear Information System (INIS)

Krishnamurty, M.V.

1978-01-01

High energy radiations are emitted in the radioactive disintegration of plutonium isotopes. These radiations mainly consisting of α-particles interact with the surrounding ligands in the case of plutonium compounds. The ligand molecules undergo electronic excitation, ionization and fragmentation resulting in extensive radiation damage. Electron paramagnetic resonance technique is utilised to indentify and estimate these molecular products formed as a result of self-irradiation in the case of sodium plutonyl acetate, NaPuO 2 (CH 3 COO) 3 , and plutonium thenoyl trifluoroacetonate, Pu(TTA) 4 . The observed EPR spectra are interpreted to be due to acetate and thenoyl trifluoroacetonate radicals with the unpaired electron localized on oxygens of carboxyl group and carbonyl group, respectively. The efficiency parameter, eta, defined as the ratio of the number of paramagnetic species/defects to the total number of radioactive disintegrations has been determined to be 0.83 and 16.9 for the case of the acetate and thenoyl trifluoroacetonate, respectivly. (author)

Formation of mixed hydroxides in the thorium chloride-iron chloride-sodium hydroxide system

International Nuclear Information System (INIS)

Krivokhatskij, A.S.; Prokudina, A.F.; Sapozhnikova, T.V.

1976-01-01

The process of formation of mixed hydroxides in the system thorium chloride-iron chloride-NaOH was studied at commensurate concentrations of Th and Fe in solution (1:1 and 1:10 mole fractions, respectively) with ionic strength 0.3, 2.1, and 4.1, created with the electrolyte NaCl, at room temperature 22+-1degC. By the methods of chemical, potentiometric, thermographic, and IR-spectrometric analyses, it was shown that all the synthesized precipitates are mechanical mixtures of two phases - thorium hydroxide and iron hydroxide - and not a new hydrated compound. The formal solubility of the precipitates of mixed hydroxides was determined. It was shown that the numerical value of the formal solubility depends on the conditions of formation and age of the precipitates

Corrosion behaviour of 2124 aluminium alloy-silicon carbide metal matrix composites in sodium chloride environment

International Nuclear Information System (INIS)

Singh, Nirbhay; Vadera, K.K.; Ramesh Kumar, A.V.; Singh, R.S.; Monga, S.S.; Mathur, G.N.

1999-01-01

Aluminium alloy based particle reinforced metal matrix composites (MMCs) are being considered for a range of applications. Their mechanical properties have been investigated in detail, but more information about their corrosion resistance is needed. In this investigation, the corrosion behaviour of silicon carbide particulates (SiC p )-2124 aluminium metal matrix composites was studied in 3 wt% sodium chloride solution by means of electrochemical technique and optical microscope. The effects of weight percentages and particle size of silicon carbide particulates on corrosion behaviour of the composite were studied in NaCl and it was observed that corrosion rate increases linearly with the increasing weight percentage of SiC p . The corrosion rate of the MMC increases by increasing the size of SiC particles. Anodization improved corrosion resistance of the composites. (author)

The influence of sodium chlorides fog on corrosion resistance of heat exchangers used in automotive

Directory of Open Access Journals (Sweden)

Peta Katarzyna

2017-01-01

Full Text Available In the work, the most important factors which influence on the exploitative durability of heat exchangers are classified. Particular attention was paid to the compounds of sodium chloride used in the winter season for road maintenance. In order to determine their impact on automotive heat exchanger corrosion resistance, a test of heaters in a salt chamber which imitates the conditions of their work was realized. It also allows to verify the durability of these products. To evaluate the corrosion changes, observation with the use of light microscopy and scanning microscopy SEM were made supplemented with microanalysis of chemical composition by EDS spectroscopy method. Critical areas in the heat exchangers which are mostly exposed to damage including the formation of local corrosion pits were located and analyzed.

Enhanced dispersion stability and mobility of carboxyl-functionalized carbon nanotubes in aqueous solutions through strong hydrogen bonds

Energy Technology Data Exchange (ETDEWEB)

Bahk, Yeon Kyoung; He, Xu; Gitsis, Emmanouil; Kuo, Yu-Ying [ETH Zurich, Institute of Environmental Engineering (Switzerland); Kim, Nayoung [EMPA, Building Energy Materials and Components (Switzerland); Wang, Jing, E-mail: jing.wang@ifu.baug.ethz.ch [ETH Zurich, Institute of Environmental Engineering (Switzerland)

2015-10-15

Dispersion of carbon nanotubes has been heavily studied due to its importance for their technical applications, toxic effects, and environmental impacts. Common electrolytes, such as sodium chloride and potassium chloride, promote agglomeration of nanoparticles in aqueous solutions. On the contrary, we discovered that acetic electrolytes enhanced the dispersion of multi-walled carbon nanotubes (MWCNTs) with carboxyl functional group through the strong hydrogen bond, which was confirmed by UV–Vis spectrometry, dispersion observations and aerosolization-quantification method. When concentrations of acetate electrolytes such as ammonium acetate (CH{sub 3}CO{sub 2}NH{sub 4}) and sodium acetate (CH{sub 3}CO{sub 2}Na) were lower than 0.03 mol per liter, MWCNT suspensions showed better dispersion and had higher mobility in porous media. The effects by the acetic environment are also applicable to other nanoparticles with the carboxyl functional group, which was demonstrated with polystyrene latex particles as an example.

Radiation Effects on Polymers - XIII

DEFF Research Database (Denmark)

El-Awady, N. I.; Ghanem, N. A.; Bo, P.

1979-01-01

Using computerized programs, the water flux and salt rejection properties in reverse osmosis of cellulose acetate-g-acrylamide membranes are determined. Comparisons are made with ungrafted commercial cellulose acetate membranes, using 0.1 and 1.0 M sodium chloride, sodium sulphate and ammonium su...... sulphate solutions. The grafted cellulose acetates show improved water flux but reduced NaCl rejection. However, they show promising prospects in bigger ion separation as for Na2SO4 and (NH4)2SO4 solutions....

Impact of combined sodium chloride and saturated long-chain fatty acid challenge on the differentiation of T helper cells in neuroinflammation.

OpenAIRE

Hammer, Anna; Jorg, Stefanie; Haghikia, Aiden; Gold, Ralf; Kleinewietfeld, Markus; Müller, Dominik N.; Linker, Ralf A.

2017-01-01

Background: There has been a marked increase in the incidence of autoimmune diseases like multiple sclerosis (MS) in the last decades which is most likely driven by a change in environmental factors. Here, growing evidence suggests that ingredients of a Western diet like high intake of sodium chloride (NaCl) or saturated fatty acids may impact systemic immune responses, thus increasing disease susceptibility. Recently, we have shown that high dietary salt or long-chain fatty acid (LCFA) intak...

The neuroprotective action of the mood stabilizing drugs lithium chloride and sodium valproate is mediated through the up-regulation of the homeodomain protein Six1

International Nuclear Information System (INIS)

Plant, Kathryn E.; Anderson, Elizabeth; Simecek, Nicole; Brown, Richard; Forster, Sam; Spinks, Jenny; Toms, Nick; Gibson, G. Gordon; Lyon, Jon; Plant, Nick

2009-01-01

The mood stabilizing agents lithium chloride (LiCl) and sodium valproate (VPA) have recently gained interest as potential neuroprotective therapeutics. However, exploitation of these therapeutic applications is hindered by both a lack of molecular understanding of the mode of action, and a number of sub-optimal properties, including a relatively small therapeutic window and variable patient response. Human neuroblastoma cells (SH-SY5Y) were exposed to 1 mM lithium chloride or 1 mM sodium valproate for 6 h or 72 h, and transcriptomes measured by Affymetrix U133A/B microarray. Statistically significant gene expression changes were identified using SAM software, with selected changes confirmed at transcript (TaqMan) and protein (Western blotting) levels. Finally, anti-apoptotic action was measured by an in vitro fluorescent assay. Exposure of SH-SY5Y cells to therapeutically relevant concentrations of either lithium chloride or sodium valproate elicited 936 statistically significant changes in gene expression. Amongst these changes we observed a large (maximal 31.3-fold) increase in the expression of the homeodomain protein Six1, and have characterized the time- and dose-dependent up-regulation of this gene in response to both drugs. In addition, we demonstrate that, like LiCl or VPA treatment, Six1 over-expression protects SH-SY5Y cells from staurosporine-induced apoptosis via the blockade of caspsase-3 activation, whereas removal of Six1 protein via siRNA antagonises the ability of LiCl and VPA to protect SH-SY5Y cells from STS-induced apoptosis. These results provide a novel mechanistic rationale underlying the neuroprotective mechanism of LiCl and VPA, suggesting exciting possibilities for the development of novel therapeutic agents against neurodegenerative diseases such as Alzheimer's or Parkinsonism

Compatibility of butorphanol with granisetron in 0.9% sodium chloride injection packaged in glass bottles or polyolefin bags.

Science.gov (United States)

Chen, Fu-Chao; Xiong, Hui; Liu, Hui-Min; Fang, Bao-Xia; Li, Peng

2015-08-15

The stability of admixtures containing butorphanol and granisetron in polyolefin bags and glass bottles stored at 4 and 25 °C was studied. Commercial solutions of butorphanol tartrate and granisetron hydrochloride were combined and further diluted with 0.9% sodium chloride injection to final concentrations of butorphanol tartrate 0.08 mg/mL and granisetron 0.03 or 0.06 mg/mL; the resulting mixtures were packaged in polyolefin bags and glass bottles. The admixtures were assessed for periods of up to 48 hours after storage at 25 °C without protection from room light and up to 14 days at 4 °C with protection from room light. The chemical stability of the admixtures was evaluated by a validated high-performance liquid chromatography (HPLC) method and by measurement of pH values. Solution appearance and color were assessed by observing the samples against room light and dark backgrounds. HPLC analysis demonstrated that the percentages of the initial concentrations of butorphanol and granisetron in the various solutions remained above 97% during the testing period. No changes in color or turbidity were observed in any of the prepared solutions. Throughout this period, pH values remained stable. Admixtures of butorphanol tartrate 0.08 mg/mL and granisetron 0.03 or 0.06 mg/mL in 0.9% sodium chloride injection in polyolefin bags or glass bottles remained stable for 48 hours when stored at 25 °C exposed to room light and for 14 days when stored at 4 °C protected from room light. Copyright © 2015 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

RNA sequencing analysis of transcriptional change in the freshwater mussel Elliptio complanata after environmentally relevant sodium chloride exposure.

Science.gov (United States)

Robertson, Laura S; Galbraith, Heather S; Iwanowicz, Deborah; Blakeslee, Carrie J; Cornman, R Scott

2017-09-01

To identify potential biomarkers of salt stress in a freshwater sentinel species, we examined transcriptional responses of the common mussel Elliptio complanata to controlled sodium chloride (NaCl) exposures. Ribonucleic acid sequencing (RNA-Seq) of mantle tissue identified 481 transcripts differentially expressed in adult mussels exposed to 2 ppt NaCl (1.2 ppt chloride) for 7 d, of which 290 had nonoverlapping intervals. Differentially expressed gene categories included ion and transmembrane transport, oxidoreductase activity, maintenance of protein folding, and amino acid metabolism. The rate-limiting enzyme for synthesis of taurine, an amino acid frequently linked to osmotic stress in aquatic species, was upregulated, as was the transmembrane ion pump sodium/potassium adenosine 5'-triphosphatase. These patterns confirm a primary transcriptional response to the experimental dose, albeit likely overlapping with nonspecific secondary stress responses. Substantial involvement of the heat shock protein 70 chaperone family and the water-transporting aquaporin family was not detected, however, in contrast to some studies in other bivalves. A subset of the most significantly regulated genes was confirmed by quantitative polymerase chain reaction in an independent sample. Cluster analysis showed separation of mussels exposed to 2 ppt NaCl from control mussels in multivariate space, but mussels exposed to 1 ppt NaCl were largely indistinguishable from controls. Transcriptome-scale analysis of salt exposure under laboratory conditions efficiently identified candidate biomarkers for further functional analysis and field validation. Environ Toxicol Chem 2017;36:2352-2366. © Published 2017 Wiley Periodicals Inc. on behalf of SETAC. This article is a US government work and, as such, is in the public domain in the United States of America. © 2017 SETAC.

Salt, chloride, bleach, and innate host defense

Science.gov (United States)

Wang, Guoshun; Nauseef, William M.

2015-01-01

Salt provides 2 life-essential elements: sodium and chlorine. Chloride, the ionic form of chlorine, derived exclusively from dietary absorption and constituting the most abundant anion in the human body, plays critical roles in many vital physiologic functions, from fluid retention and secretion to osmotic maintenance and pH balance. However, an often overlooked role of chloride is its function in innate host defense against infection. Chloride serves as a substrate for the generation of the potent microbicide chlorine bleach by stimulated neutrophils and also contributes to regulation of ionic homeostasis for optimal antimicrobial activity within phagosomes. An inadequate supply of chloride to phagocytes and their phagosomes, such as in CF disease and other chloride channel disorders, severely compromises host defense against infection. We provide an overview of the roles that chloride plays in normal innate immunity, highlighting specific links between defective chloride channel function and failures in host defense. PMID:26048979

Salt, chloride, bleach, and innate host defense.

Science.gov (United States)

Wang, Guoshun; Nauseef, William M

2015-08-01

Salt provides 2 life-essential elements: sodium and chlorine. Chloride, the ionic form of chlorine, derived exclusively from dietary absorption and constituting the most abundant anion in the human body, plays critical roles in many vital physiologic functions, from fluid retention and secretion to osmotic maintenance and pH balance. However, an often overlooked role of chloride is its function in innate host defense against infection. Chloride serves as a substrate for the generation of the potent microbicide chlorine bleach by stimulated neutrophils and also contributes to regulation of ionic homeostasis for optimal antimicrobial activity within phagosomes. An inadequate supply of chloride to phagocytes and their phagosomes, such as in CF disease and other chloride channel disorders, severely compromises host defense against infection. We provide an overview of the roles that chloride plays in normal innate immunity, highlighting specific links between defective chloride channel function and failures in host defense. © Society for Leukocyte Biology.

Surface decontamination studies using polyvinyl acetate based strippable polymer

International Nuclear Information System (INIS)

Rao, S.V.S.; Lal, K.B.

2004-01-01

Polyvinyl acetate based strippable polymer has been developed for surface decontamination. Stainless steel, mild steel, polyvinyl chloride and rubber have been selected as candidate materials for the radioactive decontamination studies. The ease of strippability and homogeneity of the polymer coating has been studied using infrared spectrophotometer. Decontamination of used radioactive respirator has been carried out and the peels obtained have been subjected to leaching and incineration studies. The infrared spectrophotometric studies also have been conducted to study the interaction between polyvinyl acetate and ions, like cesium, strontium and cobalt. (author)

Effect of sodium bicarbonate on the prevention of contrast induced nephropathy in patients undergoing coronary angiography

International Nuclear Information System (INIS)

Isono, Tsuyoshi; Kamihata, Hiroshi; Seno, Takeshi; Manabe, Kenichi; Moriguchi, Akira; Yurugi, Takatomi; Iwasaka, Toshiji; Motohiro, Masayuki

2007-01-01

Contrast induced nephropathy (CIN) remains a common complication of coronary angiography (CAG) and is associated with significant morbidity and mortality. Although a previous study reported pretreatment with sodium bicarbonate is more effective than sodium chloride for prophylaxis of CIN, this has not been a universal finding and the long-term effects of sodium bicarbonate on CIN have not been studied before. We performed a prospective, single-center, randomized trial to investigate whether CIN can be avoided by sodium bicarbonate in patients with chronic renal failure. Eighty patients with chronic renal failure (defined as serum creatinine concentration (SCr), >1.1 mg per deciliter), who were undergoing CAG, were enrolled in this study. We assigned them to either sodium chloride plus sodium bicarbonate (Group B: n=35) or sodium chloride alone (Group C: n=45). In all patients, an infusion of sodium chloride of 1 ml/kg per hour was given between 12 hours before and after the procedure. In Group B, sodium bicarbonate infusion of 1 ml/kg per hour continued from 3 hours before procedure to 6 hours after procedure, changing from sodium chloride at 1 ml/kg per hour. SCr was measured at baseline, day 1, day 2 and 1 month after the procedure. CIN was defined as a 25% increase in SCr from baseline value, or an absolute increase of at least 0.5 mg/dl, which appears within 2 days after CAG. No differences in age, sex and contrast volume were observed between the two groups. SCr at baseline was not significantly different in the two groups (Group B: 1.41±0.32 versus Group C: 1.50±0.38 mg/dl). SCr at day 2 was significantly lower in Group B than Group C (1.44±0.38 versus 1.60±0.5 mg/dl, p<0.05) and 1 month (1.28±0.27 versus 1.49±0.55 mg/dl, p<0.05). CIN occurred in 9 patients (20%) in Group C but in only 2 (6%) in Group B (p=0.03). Sodium chloride plus sodium bicarbonate is more effective than sodium chloride alone for prophylaxis of CIN and can help retain long

Molten Triazolium Chloride Systems as New Aluminum Battery Electrolytes

DEFF Research Database (Denmark)

Vestergaard, B.; Bjerrum, Niels; Petrushina, Irina

1993-01-01

-170-degrees-C) depending on melt acidity and anode material. DMTC, being specifically adsorbed and reduced on the tungsten electrode surface, had an inhibiting effect on the aluminum reduction, but this effect was suppressed on the aluminum substrate. An electrochemical process with high current density (tens...... of milliamperes per square centimeter) was observed at 0.344 V on the acidic sodium tetrachloroaluminate background, involving a free triazolium radical mechanism. Molten DMTC-AlCl3 electrolytes are acceptable for battery performance and both the aluminum anode and the triazolium electrolyte can be used as active......The possibility of using molten mixtures of 1,4-dimethyl-1,2,4-triazolium chloride (DMTC) and aluminum chloride (AlCl3) as secondary battery electrolytes was studied, in some cases extended by the copresence of sodium chloride. DMTC-AlCl, mixtures demonstrated high specific conductivity in a wide...

Simultaneous determination of triacetin, acetic ether, butyl acetate and amorolfine hydrochloride in amorolfine liniment by HPLC.

Science.gov (United States)

Gao, Yuan; Li, Li; Zhang, Jianjun; Shu, Wenjuan; Gao, Liqiong

2012-04-01

A simple, rapid, specific and precise reversed-phase high-performance liquid chromatographic method was developed for simultaneous estimation of triacetin, acetic ether, butyl acetate and amorolfine in marketed pharmaceutical liniment. Chromatographic separation was performed on a Shimadzu VP-ODS C(18) column using the mixture of citric acid-hydrochloric acid-sodium hydrate buffer (pH 3.0), acetonitrile and methanol (32:30:38) as the mobile phase at a flow rate of 1.0 mL/min with UV-detection at 215 nm. The method separated the four components simultaneously in less than 10 min. The validation of the method was performed with respect to specificity, linearity, accuracy, and precision. The calibration curves were linear in the range of 35.1-81.9 μ/mL for triacetin, 431.1-1005.9 μ/mL for acetic ether, 167.0-389.7 μ/mL for butyl acetate and 151.0-352.3 μ/mL for amorolfine. The mean 100% spiked recovery for triacetin, acetic ether, butyl acetate and amorolfine is 99.43 ± 0.42, 101.5 ± 1.09, 101.4 ± 1.02 and 100.8 ± 0.69, respectively. The intra-day and inter-day relative standard deviation values were liniment.

Controlled immobilization of palladium nanoparticles in two different fluorinated polymeric aggregate cores and their application in catalysis

DEFF Research Database (Denmark)

Kijima, Tetsushi; Javakhishvili, Irakli; Jankova Atanasova, Katja

2012-01-01

Fluoroalkyl end-capped betaine-type cooligomeric nanocomposites-immobilized palladium nanoparticles were prepared by the reactions of palladium chloride with sodium acetate in the presence of sodium chloride and the corresponding fluorinated cooligomers. Outer blocks of poly(2,3,4,5,6-pentafluoro....... These fluorinated nanocomposites-immobilized palladium nanoparticles were also applied to the catalysts for Suzuki-Miyaura cross-coupling reaction, and the different reactivity between these nanocomposites was observed....

Scientific Opinion on the safety of the complexation product of sodium tartrate and iron(III) chloride as a food additive

OpenAIRE

2015-01-01

The complexation product of sodium tartrates and iron(III) chloride (Fe mTA) is proposed for use as an anti-caking agent, only in salt or its substitutes, with a maximum use level of 106 mg Fe mTA/kg salt. Fe mTA can be expected to dissociate into its constituent iron(III) and tartrate components upon ingestion. Studies in rats demonstrated that up to 90 % of ingested DL-tartrate or tartaric acid were absorbed, studies in humans suggested that only 20 % of an ingested dose of tartaric acid we...

Effect of sodium chloride on the growth and fruiting of Cabernet Sauvignon vines

Energy Technology Data Exchange (ETDEWEB)

Hawker, J.S.; Walker, R.R.

1978-01-01

Sodium chloride was supplied to rooted cuttings of Vitis vinifera cv Cabernet Sauvignon grown in a porous growth medium at concentrations of 0, 20, 50 and 75 mM. Shoot and leaf growth and berry set and development were reduced by NaCl, the severity of the effects depending on both NaCl concentration and the age of the plants receiving the treatment. Shoots were not affected by 20 mM NaCl supplied 10 days after flowering but 50 and 75 mM NaCl caused severe stunting of shoots and 75 mM NaCl had a marked effect on berry growth and development. When NaCl was supplied to vines 10 days before flowering, 20, 50 and 75 mM NaCl inhibited shoot growth and reduced berry size and sugar content. Although NaCl caused a decrease in the rate of growth of both leaves and berries, no changes in invertase or pectin methylesterase activities were found in these organs from plants supplied with NaCl.

Compatibility of ondansetron hydrochloride and methylprednisolone sodium succinate in multilayer polyolefin containers.

Science.gov (United States)

Bougouin, Christelle; Thelcide, Chloë; Crespin-Maillard, Fabienne; Maillard, Christian; Kinowski, Jean Marie; Favier, Mireille

2005-10-01

The compatibility of ondansetron hydrochloride and methylprednisolone sodium succinate in 5% dextrose injection and 0.9% sodium chloride injection was studied. Test solutions of ondansetron hydrochloride 0.16 mg/mL and methylprednisolone sodium succinate 2.4 mg/mL were prepared in triplicate and tested in duplicate. Total volumes of 4 and 2 mL of ondansetron hydrochloride solution and methylprednisolone sodium succinate solution, respectively, were added to 50-mL multilayer polyolefin bags containing 5% dextrose injection or 0.9% sodium chloride injection. Bags were stored for 24 hours at 20-25 degrees C and for 48 hours at 4-8 degrees C. Chemical compatibility was measured with high-performance liquid chromatography, and physical compatibility was determined visually. Ondansetron hydrochloride was stable for up to 24 hours at 20-25 degrees C and up to 48 hours at 4-8 degrees C. Methylprednisolone sodium succinate was stable for up to 48 hours at 4-8 degrees C. When stored at 20-25 degrees C, methylprednisolone sodium succinate was stable for up to 7 hours in 5% dextrose injection and up to 24 hours in 0.9% sodium chloride injection. Compatibility data for solutions containing ondansetron hydrochloride plus methylprednisolone sodium succinate revealed that each drug was stable for up to 24 hours at 20-25 degrees C and up to 48 hours at 4-8 degrees C. Ondansetron 0.16 mg/mL (as the hydrochloride) and methylprednisolone 2.4 mg/mL (as the sodium succinate) mixed in 50-mL multilayer polyolefin bags were stable in both 5% dextrose injection and 0.9% sodium chloride injection for up to 24 hours at 20-25 degrees C and up to 48 hours at 4-8 degrees C.

Chloride ion-dependent surface-enhanced Raman scattering study of biotin on the silver surface

International Nuclear Information System (INIS)

Liu Fangfang; Gu Huaimin; Yuan Xiaojuan; Dong Xiao; Lin Yue

2011-01-01

In the present paper, the surface enhanced Raman scattering (SERS) technique was employed to study the SERS spectra of biotin molecules formed on the silver surface. The adsorption geometries of biotin molecules on the silver surface were analyzed based on the SERS data. It can be found that most vibration modes show a Raman shift in silver sol after the addition of sodium chloride solution. In addition, The Raman signals of biotin become weaker and weaker with the increase of the concentration of sodium chloride. This may be due to that the interaction between chloride ions and silver particles is stronger than the interaction between biotin molecules and silver particles. When the concentration of sodium chloride in silver colloid is higher than 0.05mol/L, superfluous chloride ions may form an absorption layer so that biotin can not be adsorbed on silver surface directly. The changes in intensity and profile shape in the SERS spectra suggest different adsorption behavior and surface-coverage of biotin on silver surface. The SERS spectra of biotin suggest that the contribution of the charge transfer mechanism to SERS may be dominant.

Immobilization of myoglobin in sodium alginate composite membranes

Directory of Open Access Journals (Sweden)

Katia Cecília de Souza Figueiredo

2015-06-01

Full Text Available AbstractThe immobilization of myoglobin in sodium alginate films was investigated with the aim of evaluating the protein stability in an ionic polymeric matrix. Myoglobin was chosen due to the resemblance to each hemoglobin tetramer. Sodium alginate, being a natural polysaccharide, was selected as the polymeric matrix because of its chemical structure and film-forming ability. To improve the mechanical resistance of sodium alginate films, the polymer was deposited over the surface of a cellulose acetate support by means of ultrafiltration. The ionic crosslink of sodium alginate was investigated by calcium ions. Composite membrane characterization comprised water swelling tests, water flux, SEM images and UV-visible spectroscopy. The electrostatic interaction between the protein and the polysaccharide did not damage the UV-visible pattern of native myoglobin. A good affinity between sodium alginate and cellulose acetate was observed. The top layer of the dense composite membrane successfully immobilized Myoglobin, retaining the native UV-visible pattern for two months.

Synthesis and characterization of an effective organic/inorganic hybrid green corrosion inhibitive complex based on zinc acetate/Urtica Dioica

International Nuclear Information System (INIS)

Salehi, E.; Naderi, Reza; Ramezanzadeh, B.

2017-01-01

Highlights: • An organic/inorganic hybrid green corrosion inhibitive pigment was synthesized and characterized. • Chemical structure and morphology of the hybrid complex were characterized. • Zinc acetate/Urtica Dioica showed effective inhibition action in saline solution on carbon steel. • The synergistic effect between Zn 2+ cations and inhibitive compounds existed in U.D resulted in protective film deposition on the steel surface. - Abstract: This study aims at synthesis and characterization of an effective corrosion inhibitive complex based on zinc acetate/Urtica Dioica (ZnA-U.D) for corrosion protection of mild steel in chloride solution. The chemical structure and morphology of the complex were characterized by Fourier transform infrared spectroscopy (FT-IR), UV–vis, thermal gravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The corrosion protection performance of the mild steel samples dipped in 3.5 wt.% NaCl solutions with and without ZnA-U.D extract was investigated by visual observations, open circuit potential (OCP) measurements, electrochemical impedance spectroscopy (EIS) and polarization test. Results revealed that the ZnA successfully chelated with organic inhibitive compounds (i.e Quercetin, Quinic acid, Caffeic acid, Hystamine and Serotonin) present in the U.D extract. The electrochemical measurements revealed the effective inhibition action of ZnA-U.D complex in the sodium chloride solution on the mild steel. The synergistic effect between Zn 2+ and organic compounds present in the U.D extract resulted in protective film deposition on the steel surface, which was proved by SEM and XPS analyses.

Synthesis and characterization of an effective organic/inorganic hybrid green corrosion inhibitive complex based on zinc acetate/Urtica Dioica

Energy Technology Data Exchange (ETDEWEB)

Salehi, E.; Naderi, Reza [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Ramezanzadeh, B., E-mail: ramezanzadeh@aut.ac.ir [Department of Surface Coatings and Corrosion, Institute for Color Science and Technology (ICST), PO 16765-654, Tehran (Iran, Islamic Republic of)

2017-02-28

Highlights: • An organic/inorganic hybrid green corrosion inhibitive pigment was synthesized and characterized. • Chemical structure and morphology of the hybrid complex were characterized. • Zinc acetate/Urtica Dioica showed effective inhibition action in saline solution on carbon steel. • The synergistic effect between Zn{sup 2+} cations and inhibitive compounds existed in U.D resulted in protective film deposition on the steel surface. - Abstract: This study aims at synthesis and characterization of an effective corrosion inhibitive complex based on zinc acetate/Urtica Dioica (ZnA-U.D) for corrosion protection of mild steel in chloride solution. The chemical structure and morphology of the complex were characterized by Fourier transform infrared spectroscopy (FT-IR), UV–vis, thermal gravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The corrosion protection performance of the mild steel samples dipped in 3.5 wt.% NaCl solutions with and without ZnA-U.D extract was investigated by visual observations, open circuit potential (OCP) measurements, electrochemical impedance spectroscopy (EIS) and polarization test. Results revealed that the ZnA successfully chelated with organic inhibitive compounds (i.e Quercetin, Quinic acid, Caffeic acid, Hystamine and Serotonin) present in the U.D extract. The electrochemical measurements revealed the effective inhibition action of ZnA-U.D complex in the sodium chloride solution on the mild steel. The synergistic effect between Zn{sup 2+} and organic compounds present in the U.D extract resulted in protective film deposition on the steel surface, which was proved by SEM and XPS analyses.

AFM study of the early corrosion of a high strength steel in a diluted sodium chloride solution

International Nuclear Information System (INIS)

Sanchez, Javier; Fullea, Jose; Andrade, Carmen; Gaitero, Juan J.; Porro, Antonio

2008-01-01

The high strength steels employed as reinforcement in pre-stressed concrete structures are drawn wire steels of eutectoid composition with a pearlitic microstructure. This work is focused on the study, by atomic force microscopy, of the early stages of the corrosion of such steels as a consequence of their exposition to a sodium chloride solution. The obtained images show the pearlitic microstructure of the steel, with a preferential attack of the ferrite phase and the cementite acting as a cathode. The corrosion rate was determined by calculating the amount of material lost from a roughness analysis. The obtained results are in good agreement with the predictions of Galvelel's theory, according to which the corrosion rate slows down as the pit depth increases

Anodic solution of alkali earth alloys in potassium chloride-sodium chloride melts

International Nuclear Information System (INIS)

Volkovich, A.V.

1997-01-01

Generalized results of studying the process of anodic dissolution of alkaline-earth metal alloys with zinc, aluminium and copper in the melts of KCl-NaCl equimolar mixture containing alkaline-earth metal chlorides, are presented. It is shown that during dissolution of both pure liquid metals and their alloys there is no electrode polarization in the range of the current densities lower or comparable in their values to corrosion current

Synthesis and characterization of an effective organic/inorganic hybrid green corrosion inhibitive complex based on zinc acetate/Urtica Dioica

Science.gov (United States)

Salehi, E.; Naderi, Reza; Ramezanzadeh, B.

2017-02-01

This study aims at synthesis and characterization of an effective corrosion inhibitive complex based on zinc acetate/Urtica Dioica (ZnA-U.D) for corrosion protection of mild steel in chloride solution. The chemical structure and morphology of the complex were characterized by Fourier transform infrared spectroscopy (FT-IR), UV-vis, thermal gravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The corrosion protection performance of the mild steel samples dipped in 3.5 wt.% NaCl solutions with and without ZnA-U.D extract was investigated by visual observations, open circuit potential (OCP) measurements, electrochemical impedance spectroscopy (EIS) and polarization test. Results revealed that the ZnA successfully chelated with organic inhibitive compounds (i.e Quercetin, Quinic acid, Caffeic acid, Hystamine and Serotonin) present in the U.D extract. The electrochemical measurements revealed the effective inhibition action of ZnA-U.D complex in the sodium chloride solution on the mild steel. The synergistic effect between Zn2+ and organic compounds present in the U.D extract resulted in protective film deposition on the steel surface, which was proved by SEM and XPS analyses.

Recovery of soluble chloride salts from the wastewater generated during the washing process of municipal solid wastes incineration fly ash.

Science.gov (United States)

Tang, Hailong; Erzat, Aris; Liu, Yangsheng

2014-01-01

Water washing is widely used as the pretreatment method to treat municipal solid waste incineration fly ash, which facilitates the further solidification/stabilization treatment or resource recovery of the fly ash. The wastewater generated during the washing process is a kind of hydrosaline solution, usually containing high concentrations of alkali chlorides and sulphates, which cause serious pollution to environment. However, these salts can be recycled as resources instead of discharge. This paper explored an effective and practical recovery method to separate sodium chloride, potassium chloride, and calcium chloride salts individually from the hydrosaline water. In laboratory experiments, a simulating hydrosaline solution was prepared according to composition of the waste washing water. First, in the three-step evaporation-crystallization process, pure sodium chloride and solid mixture of sodium and potassium chlorides were obtained separately, and the remaining solution contained potassium and calcium chlorides (solution A). And then, the solid mixture was fully dissolved into water (solution B obtained). Finally, ethanol was added into solutions A and B to change the solubility of sodium, potassium, and calcium chlorides within the mixed solvent of water and ethanol. During the ethanol-adding precipitation process, each salt was separated individually, and the purity of the raw production in laboratory experiments reached about 90%. The ethanol can be recycled by distillation and reused as the solvent. Therefore, this technology may bring both environmental and economic benefits.

Shock Hugoniot and equations of states of water, castor oil, and aqueous solutions of sodium chloride, sucrose and gelatin

Science.gov (United States)

Gojani, A. B.; Ohtani, K.; Takayama, K.; Hosseini, S. H. R.

2016-01-01

This paper reports a result of experiments for the determination of reliable shock Hugoniot curves of liquids, in particular, at relatively low pressure region, which are needed to perform precise numerical simulations of shock wave/tissue interaction prior to the development of shock wave related therapeutic devices. Underwater shock waves were generated by explosions of laser ignited 10 mg silver azide pellets, which were temporally and spatially well controlled. Measuring temporal variation of shock velocities and over-pressures in caster oil, aqueous solutions of sodium chloride, sucrose and gelatin with various concentrations, we succeeded to determine shock Hugoniot curves of these liquids and hence parameters describing Tait type equations of state.

Rhenium corrosion in chloride melts

International Nuclear Information System (INIS)

Stepanov, A.D.; Shkol'nikov, S.N.; Vetyukov, M.M.

1989-01-01

The results investigating rhenium corrosion in chloride melts containing sodium, potassium and chromium ions by a gravimetry potentials in argon atmosphere in a sealing quarth cell are described. Rhenium corrosion is shown to be rather considerable in melts containing CrCl 2 . The value of corrosion rate depending on temperature is determined

Experimental studies on seasonal heat storage based on stable supercooling of a sodium acetate water mixture

DEFF Research Database (Denmark)

Furbo, Simon; Dragsted, Janne; Fan, Jianhua

2011-01-01

to transfer heat to and from the module have been tested. Further, a solidification start method, based on a strong cooling of a small part of the salt water mixture in the module by boiling CO2 in a small brass tank in good thermal contact to the outer side of the module wall, has been tested. Tests......Laboratory tests of a 230 l seasonal heat storage module with a sodium acetate water mixture have been carried out. The aim of the tests is to elucidate how best to design a seasonal heat storage based on the salt water mixture, which supercools in a stable way. The module can be a part...... of a seasonal heat storage, that will be suitable for solar heating systems which can fully cover the yearly heat demand of Danish low energy buildings. The tested module has approximately the dimensions 2020 mm x 1285 mm x 80 mm. The module material is steel and the wall thickness is 2 mm. Different methods...

Thermophysical properties of sodium nitrate and sodium chloride solutions and their effects on fluid flow in unsaturated media

International Nuclear Information System (INIS)

Xu, Tianfu; Pruess, Karsten

2001-01-01

Understanding movement of saline sodium nitrate (NaNO 3 ) waste solutions is important for assessing the contaminant migration near leaking waste storage tanks in the unsaturated zone at the Hanford site (Washington, USA). The purpose of this study is to contribute a basic understanding of effects of the thermophysical behavior of NaNO 3 solutions on fluid flow in unsaturated media. We first present mathematical expressions for the dependence of density, viscosity, solubility and vapor pressure of NaNO 3 solutions on both salt concentration and temperature, which were determined by fitting from published measured data. Because the previous studies of thermophysical behavior of sodium chloride (NaCl) solutions can provide a basis for those of NaNO 3 solutions, we also present a comparison of thermophysical properties of both salt solutions. We have implemented the functional thermophysical properties of NaNO 3 solutions into a new TOUGH2 equation-of-state module EWASG-NaNO 3 , which is modified from a previous TOUGH2 equation-of-state module EWASG for NaCl. Using the simulation tool, we have investigated effects of the thermophysical properties on fluid flow in unsaturated media. The effect of density and viscosity of saline solutions has been long recognized. Here we focus our attention on the effect of vapor pressure lowering due to salinity. We present simulations of a one-dimensional problem to study this salinity-driven fluid flow. A number of simulations were performed using different values of thermal conductivity, permeability, and temperature, to illustrate conditions and parameters controlling these processes. Results indicate that heat conduction plays a very important role in this salinity-driven vapor diffusion by maintaining a nearly constant temperature. The smaller the permeability, the more water is transferred into the saline environment. Effects of permeability on water flow are also complicated by effects of capillary pressure and tortuosity. The

Inhibition treatment of the corrosion of lead artefacts in atmospheric conditions and by acetic acid vapour: use of sodium decanoate

International Nuclear Information System (INIS)

Rocca, E.; Rapin, C.; Mirambet, F.

2004-01-01

The efficiency of linear sodium decanoate, CH 3 (CH 2 ) 8 COONa (noted NaC 10 ), as corrosion inhibitor of lead was determined by electrochemical techniques in two corrosive mediums: ASTM D1384 standard water and acetic acid-enriched solutions. Best results were obtained with 0.05 mol l -1 of NaC 10 solution. In these conditions, the inhibition efficiency can be estimated of 99.9%. The corrosion inhibition effect was confirmed by cyclic atmospheric tests in a climatic chamber in two different conditions: water saturated vapour, and acid acetic enriched vapour simulating the atmosphere in the wooden displays in museums. Surface analyses by SEM and X-ray diffraction indicate that the metal protection is due to the formation of a protective layer mainly composed of lead decanoate Pb(C 10 ) 2 (metallic soap). This inhibition treatment was applied on objects of metallic cultural heritage: gallo-roman sarcophagus in lead. Electrochemical methods confirm the efficiency of treatment on archaeological materials. In conclusion, this inhibitor treatment seems to be very promising against the atmospheric corrosion and the corrosion by organic acid vapour in museums

Modeling the Combined Effects of Temperature, pH, and Sodium Chloride and Sodium Lactate Concentrations on the Growth Rate of Lactobacillus plantarum ATCC 8014

Directory of Open Access Journals (Sweden)

Francieli Dalcanton

2018-01-01

Full Text Available Nowadays, microorganisms with probiotic or antimicrobial properties are receiving major attention as alternative resources for food preservation. Lactic acid bacteria are able to synthetize compounds with antimicrobial activity against pathogenic and spoilage flora. Among them, Lactobacillus plantarum ATCC 8014 has exhibited this capacity, and further studies reveal that the microorganism is able to produce bacteriocins. An assessment of the growth of L. plantarum ATCC 8014 at different conditions becomes crucial to predict its development in foods. A response surface model of the growth rate of L. plantarum was built in this study as a function of temperature (4, 7, 10, 13, and 16°C, pH (5.5, 6.0, 6.5, 7.0, and 7.5, and sodium chloride (0, 1.5, 3.0, 4.5, and 6.0% and sodium lactate (0, 1, 2, 3, and 4% concentrations. All the factors were statistically significant at a confidence level of 90%  (p<0.10. When temperature and pH increased, there was a corresponding increase in the growth rate, while a negative relationship was observed between NaCl and Na-lactate concentrations and the growth parameter. A mathematical validation was carried out with additional conditions, demonstrating an excellent performance of the model. The developed model could be useful for designing foods with L. plantarum ATCC 8014 added as a probiotic.

Association of urinary sodium/creatinine ratio with bone mineral density in postmenopausal women: KNHANES 2008-2011.

Science.gov (United States)

Kim, Sung-Woo; Jeon, Jae-Han; Choi, Yeon-Kyung; Lee, Won-Kee; Hwang, In-Ryang; Kim, Jung-Guk; Lee, In-Kyu; Park, Keun-Gyu

2015-08-01

Accumulating evidence shows that high sodium chloride intake increases urinary calcium excretion and may be a risk factor for osteoporosis. However, the effect of oral sodium chloride intake on bone mineral density (BMD) and risk of osteoporosis has been inadequately researched. The aim of the present study was to determine whether urinary sodium excretion (reflecting oral sodium chloride intake) associates with BMD and prevalence of osteoporosis in postmenopausal women. This cross-sectional study involved a nationally representative sample consisting of 2,779 postmenopausal women who participated in the Korea National Health and Nutritional Examination Surveys in 2008-2011. The association of urinary sodium/creatinine ratio with BMD and other osteoporosis risk factors was assessed. In addition, the prevalence of osteoporosis was assessed in four groups with different urinary sodium/creatinine ratios. Participants with osteoporosis had significantly higher urinary sodium/creatinine ratios than the participants without osteoporosis. After adjusting for multiple confounding factors, urinary sodium/creatinine ratio correlated inversely with lumbar spine BMD (P = 0.001). Similarly, when participants were divided into quartile groups according to urinary sodium/creatinine ratio, the average BMD dropped as the urinary sodium/creatinine ratio increased. Multiple logistic regression analysis revealed that compared to quartile 1, quartile 4 had a significantly increased prevalence of lumbar spine osteoporosis (odds ratios 1.346, P for trend = 0.044). High urinary sodium excretion was significantly associated with low BMD and high prevalence of osteoporosis in lumbar spine. These results suggest that high sodium chloride intake decreases lumbar spine BMD and increases the risk of osteoporosis in postmenopausal women.

Chloride flux from blood to CSF: inhibition by furosemide and bumetanide

International Nuclear Information System (INIS)

Johnson, D.C.; Singer, S.; Hoop, B.; Kazemi, H.

1987-01-01

Movement of chloride from blood to cerebrospinal fluid (CSF) is one of the factors that may be involved in regulation of CSF [Cl-], which is important to CSF acid-base balance. We made quantitative measurements of the unidirectional flux of radiolabeled chloride between blood and CSF in anesthetized dogs, using 38 Cl, a short-lived isotope (half-life 37.3 min). This allowed multiple studies to be performed in a given animal. A three-compartment model for the blood, CSF, brain extracellular fluid, and ventriculocisternal perfusion system was used to determine the flux rate. With normocapnia, the flux was 0.01.1 min-1. The influx could be reproducibly measured for three separate determinations in the same animal over a period of 6 h, being 98 +/- 6% of the control first run on the second run and 113 +/- 6% on the third. Furosemide and bumetanide, inhibitors of sodium-coupled chloride movement, lowered the flux to 43 +/- 3% and 55 +/- 6% of control, respectively. The combination of hypercapnia and furosemide lowered the influx to 63 +/- 9% of control. These results indicate that a major mechanism of chloride entry into CSF is sodium-coupled chloride transport

Salt craving: The psychobiology of pathogenic sodium intake

OpenAIRE

Morris, Michael J.; Na, Elisa S.; Johnson, Alan Kim

2008-01-01

Ionic sodium, obtained from dietary sources usually in the form of sodium chloride (NaCl, common table salt) is essential to physiological function, and in humans salt is generally regarded as highly palatable. This marriage of pleasant taste and physiological utility might appear fortunate – an appealing taste helps to ensure that such a vital substance is ingested. However, the powerful mechanisms governing sodium retention and sodium balance are unfortunately best adapted for an environmen...

Homogeneous preparation of cellulose acetate propionate (CAP) and cellulose acetate butyrate (CAB) from sugarcane bagasse cellulose in ionic liquid.

Science.gov (United States)

Huang, Kelin; Wang, Ben; Cao, Yan; Li, Huiquan; Wang, Jinshu; Lin, Weijiang; Mu, Chaoshi; Liao, Dankui

2011-05-25

Cellulose acetate butyrate (CAB) and cellulose acetate propionate (CAP) were prepared homogeneously in a 1-allyl-3-methylimidazolium chloride (AmimCl) ionic liquid system from sugarcane bagasse (SB). The reaction temperature, reaction time, and molar ratio of butyric (propionic) anhydride/anhydroglucose units in the cellulose affect the butyryl (B) or propionyl (P) content of CAB or CAP samples. The (13)C NMR data revealed the distribution of the substituents of CAB and CAP. The thermal stability of sugar cane bagasse cellulose was found by thermogravimetric analysis to have decreased after chemical modification. After reaction, the ionic liquid was effectively recycled and reused. This study provides a new way for high-value-added utilization of SB and realizing the objective of turning waste into wealth.

Ion-exchange properties of cesium and strontium into zeolites from sodium salt solutions

International Nuclear Information System (INIS)

Kanno, Takuji; Hashimoto, Hiroyuki; Ohtani, Tozo.

1978-01-01

The ion-exchange properties of cesium and strontium into zeolite from sodium salt solution has been studied in zeolite A, zeolite X, zeolite Y, mordenite and clinoptilolite. The distribution of cesium into mordenite from about 1 -- 2 M sodium chloride and sodium hydroxide solutions is considerably larger than that into zeolite A. The distribution coefficient for 2 M solution of sodium salts was about 300. Therefore, the separation of cesium from sodium salt solution is possible by using mordenite. The distribution of strontium into zeolites form 1 -- 2 M solutions of sodium chloride and sodium nitrate were in the order of zeolite A>zeolite X>zeolite Y asymptoticaly equals mordenite. The distribution coefficient of 230 was obtained for 1 M solutions of sodium salts. The anion in solutions had no effect on the distribution of cesium and strontium into zeolite from sodium salt solution. (author)

Methanogenesis from acetate by Methanosarcina barkeri: Catalysis of acetate formation from methyl iodide, CO/sub 2/, and H/sub 2/ by the enzyme system involved

Energy Technology Data Exchange (ETDEWEB)

Laufer, K; Eikmanns, B; Frimmer, U; Thauer, R K

1987-04-01

Cell suspensions of Methanosarcina barkeri grown on acetate catalyze the formation of methane and CO/sub 2/ from acetate as well as an isotopic exchange between the carboxyl group of acetate and CO/sub 2/. Here we report that these cells also mediate the synthesis of acetate from methyl iodide, CO/sub 2/, and reducing equivalents (H/sub 2/ or CO), the methyl group of acetate being derived from methyl iodide and the carboxyl group from CO/sub 2/. Methyl chloride and methyltosylate but not methanol can substitute for methyl iodide in this reaction. Acetate formation from methyl iodide, CO/sub 2/, and reducing equivalents is coupled with the phosphorylation of ADP. Evidence is presented that methyl iodide is incorporated into the methyl group of acetate via a methyl corrinoid intermediate (deduced from inhibition experiments with propyl iodide) and that CO/sub 2/ is assimilated into the carboxyl group via a C/sub 1/ intermediate which does not exchange with free formate or free CO. The effects of protonophores, of the proton-translocating ATPase inhibitor N,N'-dicyclohexylcarbodiimide, and of arsenate on acetate formation are interpreted to indicate that the reduction of CO/sub 2/ to the oxidation level of the carboxyl group of acetate requires the presence of an electrochemical proton potential and that acetyl-CoA or acetyl-phosphate rather than free acetate is the immediate product of the condensation reaction. These results are dicsussed with respect to the mechanism of methanogenesis from acetate.

Correction of Hemodynamics with Hypertonic Sodium Chloride Solution in Critical Conditions

Directory of Open Access Journals (Sweden)

P. S. Zhbannikov

2007-01-01

Full Text Available Objective: to assess the capabilities of small-volume hypertonic infusion in the context of early goal-directed therapy for critical conditions in surgical patients.Subjects and methods. Twenty-nine patients (SAPS II 47.5±6.81 scores operated on for generalized peritonitis (n=24 or severe concomitant injury with damages to chest and/or abdominal organs (n=5 who had the clinical and laboratory signs of a systemic inflammatory reaction were intravenously injected 4 ml/kg of 7.5% of hypertonic sodium chloride solution (HS and colloidal solution, followed by infusion and, if indicated, inotropic maintenance of hemodynamics for 6 hours in order to achieve the goal vales of mean blood pressure (BP, central venous pressure (CVP, central venous blood oxygen saturation (ScvO2, and diuresis. Plasma concentrations of sodium, chlorine, and lactate, acid-base balance, and osmotic blood pressure were monitored.Results. The patients were found to have infusion therapy-refractory critical arterial hypotension, low ScvO2, and oliguria before small-volume circulation maintenance. In all the patients, HS infusion originally caused a rapid rise in BP up to the goal value, with its further colloid infusion maintenance requiring additional dopamine infusion in 12 patients and red blood cell transfusion in 3. This could stabilize over 6 hours BP at the required level in 25 patients, in 9 of whom CVP only approximated the goal value. All the patients were found to have a significant increase in ScvO2 up to an average of 68% in response to HP infusion after 30—60 minutes; in 14 out of them ScvO2 exceeded 70%. By hour 6, ScvO2 stabilized at its goal level in 23 (79% examinees. Administration of HS caused a significantly increased diuresis. In patients with recovered renal function, the observed hypernatremia, hyperchloremia with hyperchloremic acidosis were transient.Conclusion. The results of the study show it possible to include small-volume hypertonic infusion at

Could Sodium Chloride be an Environmental Trigger for Immune-Mediated Diseases? An Overview of the Experimental and Clinical Evidence.

Science.gov (United States)

Toussirot, Eric; Béreau, Matthieu; Vauchy, Charline; Saas, Philippe

2018-01-01

Immune mediated diseases (IMDs) are complex chronic inflammatory diseases involving genetic and environmental factors. Salt intake has been proposed as a diet factor that can influence the immune response. Indeed, experimental data report the influence of sodium chloride on the differentiation of naive CD4 + T cells into IL-17 secreting T helper (Th) cells (Th17 cells), by a mechanism involving the serum glucocorticoid kinase-1 (SGK1) that promotes the expression of the IL-23 receptor (IL-23R). The IL-23/IL-23R is critical for pathogenic inflammatory Th17 cell differentiation. Experimental data in murine models of arthritis, colitis and encephalomyelitis corroborate these findings. This manuscript reviews the current knowledge on the effects of sodium chloride on innate and adaptive immunity. We also performed a systematic literature review for clinical studies examining the relationships between salt consumption and the development or the activity/severity of the most common IMDs mediated by the IL-23/Th17 pathway, i.e., rheumatoid arthritis (RA), multiple sclerosis (MS), and Crohn's disease (CD). Nine studies were found, 4 in RA, 4 in MS and 1 in CD. An association was found between developments of anti-citrullinated protein antibody (ACPA) positive RA in smokers and salt intake, but these results were not confirmed in another study. For MS, no association was observed in pediatric subjects while in adult patients, a link was found between salt intake and disease activity. However, this result was not confirmed in another study. These conflicting results highlight the fact that further evaluation in human IMDs is required. Moreover, physicians need to develop clinical trials with diet interventions to evaluate the impact of low salt intake on disease activity/severity of IMDs.

Could Sodium Chloride be an Environmental Trigger for Immune-Mediated Diseases? An Overview of the Experimental and Clinical Evidence

Directory of Open Access Journals (Sweden)

Eric Toussirot

2018-04-01

Full Text Available Immune mediated diseases (IMDs are complex chronic inflammatory diseases involving genetic and environmental factors. Salt intake has been proposed as a diet factor that can influence the immune response. Indeed, experimental data report the influence of sodium chloride on the differentiation of naive CD4+ T cells into IL-17 secreting T helper (Th cells (Th17 cells, by a mechanism involving the serum glucocorticoid kinase-1 (SGK1 that promotes the expression of the IL-23 receptor (IL-23R. The IL-23/IL-23R is critical for pathogenic inflammatory Th17 cell differentiation. Experimental data in murine models of arthritis, colitis and encephalomyelitis corroborate these findings. This manuscript reviews the current knowledge on the effects of sodium chloride on innate and adaptive immunity. We also performed a systematic literature review for clinical studies examining the relationships between salt consumption and the development or the activity/severity of the most common IMDs mediated by the IL-23/Th17 pathway, i.e., rheumatoid arthritis (RA, multiple sclerosis (MS, and Crohn's disease (CD. Nine studies were found, 4 in RA, 4 in MS and 1 in CD. An association was found between developments of anti-citrullinated protein antibody (ACPA positive RA in smokers and salt intake, but these results were not confirmed in another study. For MS, no association was observed in pediatric subjects while in adult patients, a link was found between salt intake and disease activity. However, this result was not confirmed in another study. These conflicting results highlight the fact that further evaluation in human IMDs is required. Moreover, physicians need to develop clinical trials with diet interventions to evaluate the impact of low salt intake on disease activity/severity of IMDs.

Microbial Growth in the Magnesium- Chloride - Sodium- Sulphate Ion System: Implications for Habitability in Terrestrial and Extraterrestrial Salts

Science.gov (United States)

Loudon, C. M.; Aka, S.; Cockell, C. S.

2017-12-01

Icy moons in the outer solar system are key targets in the search for extra-terrestrial life as there is evidence that they harbour subsurface oceans. Observational evidence of icy moons such as Europa suggest that these likely brine oceans should be composed of chloride and sulphate salts. The effects of the ions that compose these salts on biology and how the interactions between them can create geochemical and geophysical barriers to life are poorly understood. Here we present an in depth study of four microorganisms grown in solutions with varying combinations of the magnesium- chloride- sodium- sulphate ions. We find that the ion composition of the brine solution can have a large effect on growth. Whilst the water activity must be permissible for growth we found that this alone could not predict the effects of the ions on growth, chaotropic effects and ion specific effects influenced by the specific physiology of organisms are also evident. For this reason we conclude that simply knowing which salts are present on icy moons is not sufficient information to determine their potential habitibility. A full sample of any brine ocean would need to be studied to fully determine the potential for biology on these outer solar system satellites.

Prevention of Contrast-Induced Nephropathy With N-Acetylcysteine or Sodium Bicarbonate in Patients With ST-Segment-Myocardial Infarction

DEFF Research Database (Denmark)

Thayssen, Per; Lassen, Jens Flensted; Jensen, Svend Eggert

2014-01-01

(CINSTEMI) trial. Patients were randomly assigned in a 1:1:1:1 ratio to receive hydration with sodium chloride together with 1 of 4 prophylactic regimes (1) N-acetylcysteine (NAC), (2) sodium bicarbonate (NaHCO3) infusion, (3) NAC in combination with NaHCO3, or (4) hydration with sodium chloride infusion...... not reduce the rate of CIN significantly compared with hydration with intravenous sodium chloride infusion alone (20.1% versus 20.1% versus 20.8% versus 26.5%; P=NS). However, an increase in serum creatinine >25% from the baseline value to 30 day was significantly lower in patients treated with combined NAC...

Removal of chloride from MSWI fly ash.

Science.gov (United States)

Chen, Wei-Sheng; Chang, Fang-Chih; Shen, Yun-Hwei; Tsai, Min-Shing; Ko, Chun-Han

2012-10-30

The high levels of alkali chloride and soluble metal salts present in MSWI fly ash is worth noting for their impact on the environment. In addition, the recycling or reuse of fly ash has become an issue because of limited landfill space. The chloride content in fly ash limits its application as basis for construction materials. Water-soluble chlorides such as potassium chloride (KCl), sodium chloride (NaCl), and calcium chloride hydrate (CaCl(2) · 2H(2)O) in fly ash are easily washed away. However, calcium chloride hydroxide (Ca(OH)Cl) might not be easy to leach away at room temperature. The roasting and washing-flushing processes were applied to remove chloride content in this study. Additionally, air and CO(2) were introduced into the washing process to neutralize the hazardous nature of chlorides. In comparison with the water flushing process, the roasting process is more efficient in reducing the process of solid-liquid separation and drying for the reuse of Cl-removed fly ash particles. In several roasting experiments, the removal of chloride content from fly ash at 1050°C for 3h showed the best results (83% chloride removal efficiency). At a solid to liquid ratio of 1:10 the water-flushing process can almost totally remove water-soluble chloride (97% chloride removal efficiency). Analyses of mineralogical change also prove the efficiency of the fly ash roasting and washing mechanisms for chloride removal. Copyright © 2012 Elsevier B.V. All rights reserved.

Kinetics of the oxidative hydroxylation of sodium hypophosphite in the presence of copper (II chloride modified by humic (fulvo- acid

Directory of Open Access Journals (Sweden)

Zhaksyntay Kairbekov

2012-12-01

Full Text Available It was established that in soft conditions (50-70oC, PO2 = 1 atm sodium hypophosphite effectively is oxidized by oxygen in water solutions of copper(II chloride  to give mainly a phosphorous acid. Humic (fulvo- acid was extracted from brown coal of domestic deposit Kiyakty. For determination of optimum parameters of fulvo-acid extraction the laboratory experiments were carried out using the method of experiment planning. The kinetics, the intermediate and final products, optimal conditions of new catalytic reaction of NaH2PO2 oxidation by oxygen in water solution were defined by kinetics, volumometry, redox-potentiometry and a titration.

Absorption, distribution and excretion of triphenyltin acetate and stannic chloride in guinea pig

Energy Technology Data Exchange (ETDEWEB)

Nagamatsu, K; Kido, Y; Urakubo, G; Aida, Y; Ikeda, Y [National Inst. of Hygienic Sciences, Tokyo (Japan)

1978-08-01

Percutaneous absorption of /sup 113/Sn-triphenyltin acetate was studied with guinea pig skin. Three and eight % of the applied /sup 113/Sn dose were absorbed through the skin, and 16 and 12% were found in the applied areas 1 and 2 days after the application, respectively. After subcutaneons injection of /sup 113/Sn-triphenyltin acetate, radioactivity was found in large amount in livers, kidneys and brains. The body retention of radioactivity showed biological half time of 9.4 days, and about 83% of the dose was excreted in feces within 20 days of dosage. After subcutaneons injection of /sup 113/SnCl/sub 4/, the radioactivity concentration was greatest in bones and kidneys. No transfer to brains was detected. Absorption from the injected sites and excretion, main route of which was urination, were greatly delayed. The biological half time was estimated to be 26.5 days. The intact compounds, /sup 113/Sn-diphenyltin and /sup 113/Sn-mono-phenyltin, were identified as the chemical forms of radiotin excreted in feces after subcutaneous injection of /sup 113/Sn-triphenyltin acetate.

Analysis of PWR auxiliary coolant: determination of chloride in borax/nitrite solution by known addition - known dilution potentiometry

International Nuclear Information System (INIS)

Midgley, D.; Gatford, C.

1989-11-01

Chloride concentrations of 75-250 μg 1 -1 have been determined in simulated PWR auxiliary coolant containing 1000 mg l -1 each of sodium tetraborate and sodium nitrite. The effects of the two main components of the coolant solution on a variety of chloride-selective electrodes have been studied. Sodium tetraborate posed no problem except through its effect on the pH, which is easily adjusted. Such high concentrations of nitrite, however, caused significant deviations in e.m.f. for all the electrodes and marked tarnishing of the electroactive membrane after only one or two measurements. Sulphamic acid was selected as the best means of removing nitrite and silver chloride electrodes were preferred over mercury(I) chloride electrodes because of their greater robustness in the conditions. At these chloride concentrations, the electrodes are operating in their non-Nernstian response regions and direct potentiometry has poor precision, even if standards could be successfully matched to samples containing such high concentrations of background material. Known addition - known dilution potentiometry was adopted, with internal calibration for both slope factor and standard potential. (author)

Operational Environmental Assessment

Science.gov (United States)

1988-09-01

Anhydride 0 oz Cupric Sulfide 5 lb Oxalic Acid 56 oz Potassium Carbonate Anhydrous 32 oz Potassium Phosphate 36 oz Sodium Acetate 44 oz Sodium...Benzene 35,500 ml Antimony Potassium Tartrate 4,000 gm Barbituric Acid 150 gm Barbituric Acid 400 gm Chromium Trioxide 6,000 gm Disodium Ethylenediamine...Hydrocholoride 600 gm *Benzene a pt Boric Acid 5,000 gm Calcium Chloride 6,500 gm Calcium Chloride 3 lb Citric Acid 3 lb Citric Acid 2,500 gm Cupric Sulfate 2,500

Electrochemical Migration on Electronic Chip Resistors in Chloride Environments

DEFF Research Database (Denmark)

Minzari, Daniel; Jellesen, Morten Stendahl; Møller, Per

2009-01-01

Electrochemical migration behavior of end terminals on ceramic chip resistors (CCRs) was studied using a novel experimental setup in varying sodium chloride concentrations from 0 to 1000 ppm. The chip resistor used for the investigation was 10-kΩ CCR size 0805 with end terminals made of 97Sn3Pb...... rate of the Sn and stability of Sn ions in the solution layer play a significant role in the formation of dendrites, which is controlled by chloride concentration and potential bias. Morphology, composition, and resistance of the dendrites were dependent on chloride concentration and potential....

In vitro incorporation of (U-C/sup 14/)-glucose and (1-C/sup 14/)-sodium acetate in peripheral nerves of malnourished young rhesus monkeys

Energy Technology Data Exchange (ETDEWEB)

Rana, S V; Mehta, S; Chopra, J S; Nain, C K; Mehta, J; Dhand, U K

1984-01-01

The effect of protein calorie malnutrition (PCM) on synthesis of lipids in peripheral nerves was studied by in vitro incorporation of (U-C/sup 14/)-glucose and (1-C/sup 14/)-sodium acetate. Ulnar and tibial nerves obtained from five young rhesus monkeys with PCM, five rehabilitated monkeys, and five control monkeys were incubated for 2 h with the radioactive precursors. Uptake of both radioactive precursors in whole peripheral nerves as well as myelin marker lipids was significantly decreased in animals with PCM. However, uptake returned to normal in rehabilitated monkeys.

Accumulation of dissolved gases at hydrophobic surfaces in water and sodium chloride solutions: Implications for coal flotation

Energy Technology Data Exchange (ETDEWEB)

Hampton, M.A.; Nguyen, A.V. [University of Queensland, Brisbane, Qld. (Australia). Division of Chemical Engineering

2009-08-15

Dissolved gases can preferentially accumulate at the hydrophobic solid-water interface as revealed by neutron reflectivity measurements. In this paper, atomic force microscopy (AFM) was used to examine accumulation of dissolved gases at a hydrophobic surface in water and sodium chloride solutions. The solvent-exchange method was used to artificially form gaseous domains accumulated at the interface suitable for AFM imaging. Smooth graphite surfaces were used as model surfaces to minimize the secondary effect of surface roughness on the imaging. The concentration of NaCl up to 1 M was found to have a negligible influence on the geometry and population of pre-existing nanobubbles, nanopancakes and nanobubble-nanopancake composites. The implications of the findings on coal flotation in saline water are discussed in terms of attraction between hydrophobic surfaces in water, bubble-particle attachment and hydrophobic coagulation between particles.

Inactivation of Biological Agents Using Neutral Oxone-Chloride Solutions

National Research Council Canada - National Science Library

Delcomyn, Carrie A; Bushway, Karen E; Henley, Michael V

2006-01-01

... to contaminated equipment or terrain. A neutral, bicarbonate-buffered aqueous solution of Oxone and sodium chloride that rapidly generates hypochlorite and hypochlorous acid in situ was evaluated as a new alternative to bleach...

Captive solvent [11C]acetate synthesis in GMP conditions

International Nuclear Information System (INIS)

Soloviev, Dmitri; Tamburella, Claire

2006-01-01

Reliable procedure for the production of 1-[ 11 C]acetate in GMP conditions was developed based on a combination of the captive-solvent Grignard reaction conducted in the sterile catheter followed by the convenient solid-phase extraction purification on a series of ion-exchange cartridges. The described procedure proved to be reliable in more than 30 patient productions. The process provides stable radiochemical yields (65% EOB) of sodium acetate (1-[ 11 C]) of the Ph.Eur. quality (radiochemical purity better than 95%) in a short time (5 min)

33 Effects of Sodium Chloride Solutions on Compressive Strength ...

African Journals Online (AJOL)

Arc. Usman A. Jalam

strength increase at 3 and 7 days over control cubes; at 28 days concrete cubes containing 5%. RHA cured in NaCl solutions recorded higher strength loss compared to control cubes. Keywords: ... chloride in mixing water reported it to cause.

Resistance of Streptococcus bovis to acetic acid at low pH: Relationship between intracellular pH and anion accumulation

Energy Technology Data Exchange (ETDEWEB)

Russell, J.B. (Cornell Univ., Ithaca, NY (USA))

1991-01-01

Streptococcus bovis JB1, an acid-tolerant ruminal bacterium, was able to grown at pHs from 6.7 to 4.5, and 100 mM acetate had little effect on growth rate or proton motive force across the cell membrane. When S. bovis was grown in glucose-limited chemostats at pH 5.2, the addition of sodium acetate (as much as 100 mM) had little effect on the production of bacterial protein. At higher concentrations of sodium acetate (100 to 360 mM), production of bacterial protein declined, but this decrease could largely be explained by a shift in fermentation products (acetate, formate, and ethanol production to lactate production) and a decline in ATP production (3 ATP per glucose versus 2 ATP per glucose). Y{sub ATP} (grams of cells per mole at ATP) was not decreased significantly even by high concentrations of acetate. Cultures supplemented with 100 mM sodium acetate took up ({sup 14}C)acetate and ({sup 14}C)benzoate in accordance with the Henderson-Hasselbalch equation and gave similar estimates of intracellular pH. As the extracellular pH declined, S. bovis allowed its intracellular pH to decrease and maintained a relatively constant pH gradient across the cell membrane (0.9 unit). The decrease in intracellular pH prevented S. bovis from accumulating large amounts of acetate anion. On the basis of these results it did not appear that acetate was acting as an uncoupler. The sensitivity of other bacteria to volatile fatty acids at low pH is explained most easily by a high transmembrane pH gradient and anion accumulation.

Resistance of Streptococcus bovis to acetic acid at low pH: Relationship between intracellular pH and anion accumulation

International Nuclear Information System (INIS)

Russell, J.B.

1991-01-01

Streptococcus bovis JB1, an acid-tolerant ruminal bacterium, was able to grown at pHs from 6.7 to 4.5, and 100 mM acetate had little effect on growth rate or proton motive force across the cell membrane. When S. bovis was grown in glucose-limited chemostats at pH 5.2, the addition of sodium acetate (as much as 100 mM) had little effect on the production of bacterial protein. At higher concentrations of sodium acetate (100 to 360 mM), production of bacterial protein declined, but this decrease could largely be explained by a shift in fermentation products (acetate, formate, and ethanol production to lactate production) and a decline in ATP production (3 ATP per glucose versus 2 ATP per glucose). Y ATP (grams of cells per mole at ATP) was not decreased significantly even by high concentrations of acetate. Cultures supplemented with 100 mM sodium acetate took up [ 14 C]acetate and [ 14 C]benzoate in accordance with the Henderson-Hasselbalch equation and gave similar estimates of intracellular pH. As the extracellular pH declined, S. bovis allowed its intracellular pH to decrease and maintained a relatively constant pH gradient across the cell membrane (0.9 unit). The decrease in intracellular pH prevented S. bovis from accumulating large amounts of acetate anion. On the basis of these results it did not appear that acetate was acting as an uncoupler. The sensitivity of other bacteria to volatile fatty acids at low pH is explained most easily by a high transmembrane pH gradient and anion accumulation

Effects of Cations on Corrosion of Inconel 625 in Molten Chloride Salts

Science.gov (United States)

Zhu, Ming; Ma, Hongfang; Wang, Mingjing; Wang, Zhihua; Sharif, Adel

2016-04-01

Hot corrosion of Inconel 625 in sodium chloride, potassium chloride, magnesium chloride, calcium chloride and their mixtures with different compositions is conducted at 900°C to investigate the effects of cations in chloride salts on corrosion behavior of the alloy. XRD, SEM/EDS were used to analyze the compositions, phases, and morphologies of the corrosion products. The results showed that Inconel 625 suffers more severe corrosion in alkaline earth metal chloride molten salts than alkaline metal chloride molten salts. For corrosion in mixture salts, the corrosion rate increased with increasing alkaline earth metal chloride salt content in the mixture. Cations in the chloride molten salts mainly affect the thermal and chemical properties of the salts such as vapor pressure and hydroscopicities, which can affect the basicity of the molten salt. Corrosion of Inconel 625 in alkaline earth metal chloride salts is accelerated with increasing basicity.

Outcomes after Angiography with Sodium Bicarbonate and Acetylcysteine.

Science.gov (United States)

Weisbord, Steven D; Gallagher, Martin; Jneid, Hani; Garcia, Santiago; Cass, Alan; Thwin, Soe-Soe; Conner, Todd A; Chertow, Glenn M; Bhatt, Deepak L; Shunk, Kendrick; Parikh, Chirag R; McFalls, Edward O; Brophy, Mary; Ferguson, Ryan; Wu, Hongsheng; Androsenko, Maria; Myles, John; Kaufman, James; Palevsky, Paul M

2018-02-15

Intravenous sodium bicarbonate and oral acetylcysteine are widely used to prevent acute kidney injury and associated adverse outcomes after angiography without definitive evidence of their efficacy. Using a 2-by-2 factorial design, we randomly assigned 5177 patients at high risk for renal complications who were scheduled for angiography to receive intravenous 1.26% sodium bicarbonate or intravenous 0.9% sodium chloride and 5 days of oral acetylcysteine or oral placebo; of these patients, 4993 were included in the modified intention-to-treat analysis. The primary end point was a composite of death, the need for dialysis, or a persistent increase of at least 50% from baseline in the serum creatinine level at 90 days. Contrast-associated acute kidney injury was a secondary end point. The sponsor stopped the trial after a prespecified interim analysis. There was no interaction between sodium bicarbonate and acetylcysteine with respect to the primary end point (P=0.33). The primary end point occurred in 110 of 2511 patients (4.4%) in the sodium bicarbonate group as compared with 116 of 2482 (4.7%) in the sodium chloride group (odds ratio, 0.93; 95% confidence interval [CI], 0.72 to 1.22; P=0.62) and in 114 of 2495 patients (4.6%) in the acetylcysteine group as compared with 112 of 2498 (4.5%) in the placebo group (odds ratio, 1.02; 95% CI, 0.78 to 1.33; P=0.88). There were no significant between-group differences in the rates of contrast-associated acute kidney injury. Among patients at high risk for renal complications who were undergoing angiography, there was no benefit of intravenous sodium bicarbonate over intravenous sodium chloride or of oral acetylcysteine over placebo for the prevention of death, need for dialysis, or persistent decline in kidney function at 90 days or for the prevention of contrast-associated acute kidney injury. (Funded by the U.S. Department of Veterans Affairs Office of Research and Development and the National Health and Medical Research

Glucose & sodium chloride induced biofilm production & ica operon in clinical isolates of staphylococci

Directory of Open Access Journals (Sweden)

Astha Agarwal

2013-01-01

Full Text Available Background & objectives: All colonizing and invasive staphylococcal isolates may not produce biofilm but may turn biofilm producers in certain situations due to change in environmental factors. This study was done to test the hypothesis that non biofilm producing clinical staphylococci isolates turn biofilm producers in presence of sodium chloride (isotonic and high concentration of glucose, irrespective of presence or absence of ica operon. Methods: Clinical isolates of 100 invasive, 50 colonizing and 50 commensal staphylococci were tested for biofilm production by microtiter plate method in different culture media (trypticase soy broth alone or supplemented with 0.9% NaCl/ 5 or 10% glucose. All isolates were tested for the presence of ica ADBC genes by PCR. Results: Biofilm production significantly increased in the presence of glucose and saline, most, when both glucose and saline were used together. All the ica positive staphylococcal isolates and some ica negative isolates turned biofilm producer in at least one of the tested culture conditions. Those remained biofilm negative in different culture conditions were all ica negative. Interpretation & conclusions: The present results showed that the use of glucose or NaCl or combination of both enhanced biofilm producing capacity of staphylococcal isolates irrespective of presence or absence of ica operon.

Extractive process for preparing high purity magnesium chloride hexahydrate

Directory of Open Access Journals (Sweden)

Fezei Radouanne

2012-01-01

Full Text Available This paper refers a method for the preparation of magnesium chloride hexahydrate (bischofite from Sebkha el Melah of Zarzis Tunisian natural brine. It is a five-stage process essentially based on crystallization by isothermal evaporation and chemical precipitation. The two first steps were dedicated to the crystallization of sodium chloride and potassiummagnesium double salts, respectively. Then, the resulting liquor was desulfated using calcium chloride solution. After that another isothermal evaporation stage was implemented in order to eliminate potassium ions in the form of carnallite, KCl.MgCl2.6H2O. At the end of this step, the recovered solution primarily composed of magnesium and chloride ions was treated by dioxan in order to precipitate magnesium chloride as MgCl2.6H2O.C4H8O2. This compound dried at constant temperature of 100°C gave good quality magnesium chloride hexahydrate. Besides this salt, the various by-products obtained from the different treatment stages are also useful.

Reactions of enolisable ketones with dichloroisocyanuric acid in absence and presence of added chloride ions – a kinetic study

Directory of Open Access Journals (Sweden)

Y. L. Kumar

2015-01-01

Full Text Available Kinetics of reactions of enolisable ketones (S = acetone/2-butanone with dichloroisocyanuric acid (DCICA were studied in aqueous acetic acid and perchloric acid media in absence and presence of added chloride ions. The reactions were found to be pseudo zero order and pseudo first order on [DCICA] in absence and presence of chloride ions respectively. Both in presence and absence of chloride ions, first order and fractional order in substrate and perchloric acid were observed respectively. An increase in the rate of reaction was observed with an increase in chloride ion concentration as well as acetic acid composition. The results were interpreted in terms of probable mechanisms involving (i rate-determining enol formation from the conjugate acid of the ketone (SH+ in the absence of added chloride ions and (ii rate-determining interaction of SH+ with the most effective molecular chlorine species produced by the hydrolysis of DCICA (rather than a rate-determining interaction of enol with chlorine in the presence of added chloride ions, prior to the rapid steps of product formation. DOI: http://dx.doi.org/10.4314/bcse.v29i1.12

Sodium chloride crystallization from thin liquid sheets, thick layers, and sessile drops in microgravity

Science.gov (United States)

Fontana, Pietro; Pettit, Donald; Cristoforetti, Samantha

2015-10-01

Crystallization from aqueous sodium chloride solutions as thin liquid sheets, 0.2-0.7 mm thick, with two free surfaces supported by a wire frame, thick liquid layers, 4-6 mm thick, with two free surfaces supported by metal frame, and hemispherical sessile drops, 20-32 mm diameter, supported by a flat polycarbonate surface or an initially flat gelatin film, were carried out under microgravity on the International Space Station (ISS). Different crystal morphologies resulted based on the fluid geometry: tabular hoppers, hopper cubes, circular [111]-oriented crystals, and dendrites. The addition of polyethylene glycol (PEG-3350) inhibited the hopper growth resulting in flat-faced surfaces. In sessile drops, 1-4 mm tabular hopper crystals formed on the free surface and moved to the fixed contact line at the support (polycarbonate or gelatin) self-assembling into a shell. Ring formation created by sessile drop evaporation to dryness was observed but with crystals 100 times larger than particles in terrestrially formed coffee rings. No hopper pyramids formed. By choosing solution geometries offered by microgravity, we found it was possible to selectively grow crystals of preferred morphologies.

The use of immobilized form of benzalkonium chloride and metronidazole in the treatment of purulent wounds

OpenAIRE

Anastasia S. Gorohova; Arsen Yu. Grigoryan; Alexander I. Bezhin; Tatyana A. Pankrusheva; Boris S. Sukovatykh; Ludmila V. Zhilyaeva; Ekaterina S. Mishina; Elena V. Kobzareva

2017-01-01

The purpose of the study is to investigate the wound-healing effect of the immobilized form of benzalkonium chloride and metronidazole based on the sodium salt of carboxymethylcellulose (Na-CMC) or polyethylene oxide (PEO) in the treatment of an experimental purulent wound.Materials and methods. The following compositions were studied, %. Combination 1: benzalkonium chloride – 0.02; Metronidazole – 1,0; Sodium carboxymethylcellulose (NaCMC) – 4,0; Purified water – up to 100,0. Combination 2: ...

Potato plants (Solanum tuberosum L.) are chloride-sensitive: Is this dogma valid?

Science.gov (United States)

Hütsch, Birgit W; Keipp, Katrin; Glaser, Ann-Kathrin; Schubert, Sven

2018-06-01

Chloride sensitivity of the potato (Solanum tuberosum L.) cultivars Marabel and Désirée was investigated in two pot experiments (soil/sand mixture and hydroponics). It was tested whether there are differential effects of KCl and K 2 SO 4 application on tuber yield and tuber quality, and whether both potato cultivars differ in their chloride sensitivity. Tuber yield, dry matter percentage of the tubers, starch concentration and starch yield were not significantly affected by potassium source (K 2 SO 4 or KCl). After exposure to salt stress in hydroponics (100 mmol L -1 NaCl, 50 mmol L -1 Na 2 SO 4 , 50 mmol L -1 CaCl 2 ) for 5 days, 3-week-old potato plants had significantly reduced shoot dry mass after NaCl and Na 2 SO 4 application. However, CaCl 2 treatment did not significantly affect shoot growth, although the chloride concentration reached 65 to 74 mg Cl - mg -1 dry matter, similar to the NaCl treatment. In contrast, growth reductions were closely related to sodium concentrations, thus plants suffered sodium toxicity and not chloride toxicity. Both potato cultivars are chloride-resistant and can be fertilised with KCl instead of K 2 SO 4 without the risk of depression in tuber yield or tuber quality. The statement that potatoes are chloride-sensitive and that chloride has negative effects on yield performance needs reconsideration. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Stability of Fentanyl Citrate, Hydromorphone Hydrochloride, Ketamine Hydrochloride, Midazolam, Morphine Sulfate, and Pentobarbital Sodium in Polypropylene Syringes

OpenAIRE

Anderson, Collin; MacKay, Mark

2015-01-01

Purpose: Determine the stability of fentanyl 10 mcg/mL in 0.9% sodium chloride, fentanyl 10 mcg/mL in 5% dextrose, fentanyl 50 mcg/mL, hydromorphone 100 mcg/mL in 0.9% sodium chloride, ketamine 10 mg/mL, midazolam 0.4 mg/mL in 5% dextrose, midazolam 5 mg/mL, morphine 1 mg/mL in 0.9% sodium chloride, morphine 1 mg/mL in 5% dextrose, and pentobarbital 50 mg/mL when stored as single drug entities at room temperature in polypropylene syringes. Methods: Four 5 mL samples of each drug and concentra...

Ionic strength dependence of the oxidation of SO2 by H2O2 in sodium chloride particles

Science.gov (United States)

Ali, H. M.; Iedema, M.; Yu, X.-Y.; Cowin, J. P.

2014-06-01

The reaction of sulfur dioxide and hydrogen peroxide in the presence of deliquesced (>75% RH) sodium chloride (brine) particles was studied by utilizing a cross flow mini-reactor. The reaction kinetics were followed by observing chloride depletion in particles by computer-controlled scanning electron microscope with energy dispersive X-ray analysis, namely CCSEM/EDX. The reactions take place in concentrated mixed salt brine aerosols, for which no complete kinetic equilibrium data previously existed. We measured the Henry's law solubility of H2O2 in brine solutions to close that gap. We also calculated the reaction rate as the particle transforms continuously from concentrated NaCl brine to, eventually, a mixed NaHSO4 plus H2SO4 brine solution. The reaction rate of the SO2 oxidation by H2O2 was found to be influenced by the change in ionic strength as the particle undergoes compositional transformation, following closely the dependence of the third order rate constant on ionic strength as predicted using established rate equations. This is the first study that has measured the ionic strength dependence of sulfate formation (in non-aqueous media) from oxidation of mixed salt brine aerosols in the presence of H2O2. It also gives the first report of the dependence of the Henry's law constant of H2O2 on ionic strength.

Effects of calcium and magnesium acetates on tissue distribution of carcinogenic doses of calcium chloride in Wistar rats

International Nuclear Information System (INIS)

Kasprzak, K.S.; Poirier, L.A.

1985-01-01

Previous studies have shown that magnesium, unlike calcium, prevents cadmium carcinogenesis at the subcutaneous injection site, and that neither magnesium nor calcium has any significant influence on the production of testicular tumors by cadmium in rats. The present investigation attempts to disclose the nature of those different effects by comparing the results of administration of both physiological metals on the uptake and distribution of carcinogenic doses of cadmium in rats. Male Wistar rats received a single subcutaneous (s.c.) injection of 109 CdCl 2 (0.02 mmol/kg or 0.04 mmol/kg) and s.c. injections (one daily) of calcium acetate (CaAcet; 0.16 mmol/kg), or magnesium acetate (MgAcet; 4 mmol/kg) or saline on the day before, the day of and the day after the 109 CdCl 2 dosing. The concentration of cadmium in tissues was determined by gamma-counting on the 4th, the 15th and the 45th day after 109 CdCl 2 injection. The concentration of cadmium in tissues on day 4 was ranked as follows: liver > kidney > the injection site skin > pancreas > spleen > heart > lung > distant skin > testes > blood. Administration of CaAcet increased by over 20% and that of MgAcet decreased by over 30% the initial uptake of both cadmium doses at the injection site. The MgAcet may prevent cadmium carcinogenesis by inhiniting the uptake of cadmium by the injection site tissues. In the testis and in all other tissues investigated, except kidney, the effects of the physiological metals were reversed, CaAcet and MgAcet tended to increase the uptake of cadmium. CaAcet exerted no noticeable effects on the uptake of cadmium by the kidney. The observed results of CaAcet and MgAcet administration on the concentration of cadmium in distal tissues seem to depend on the alterations in cadmium uptake at the injection site. (author)

Effects of dietary glucose and sodium chloride on intestinal glucose absorption of common carp (Cyprinus carpio L.).

Science.gov (United States)

Qin, Chaobin; Yang, Liping; Zheng, Wenjia; Yan, Xiao; Lu, Ronghua; Xie, Dizhi; Nie, Guoxing

2018-01-08

The co-transport of sodium and glucose is the first step for intestinal glucose absorption. Dietary glucose and sodium chloride (NaCl) may facilitate this physiological process in common carp (Cyprinus carpio L.). To test this hypothesis, we first investigated the feeding rhythm of intestinal glucose absorption. Carps were fed to satiety once a day (09:00 a.m.) for 1 month. Intestinal samples were collected at 01:00, 05:00, 09:00, 13:00, 17:00 and 21:00. Result showed that food intake greatly enhanced sodium/glucose cotransporter 1 (SGLT1) and glucose transporter type 2 (GLUT2) expressions, and improved glucose absorption, with highest levels at 09:00 a.m.. Then we designed iso-nitrogenous and iso-energetic diets with graded levels of glucose (10%, 20%, 30%, 40% and 50%) and NaCl (0%, 1%, 3% and 5%), and submitted to feeding trial for 10 weeks. The expressions of SGLT1 and GLUT2, brush border membrane vesicles (BBMVs) glucose transport and intestinal villus height were determined after the feeding trial. Increasing levels of dietary glucose and NaCl up-regulated mRNA and protein levels of SGLT1 and GLUT2, enhanced BBMVs glucose transport in the proximal, mid and distal intestine. As for histological adaptive response, however, high-glucose diet prolonged while high-NaCl diet shrank intestinal villus height. Furthermore, we also found that higher mRNA levels of SGLT1 and GLUT2, higher glucose transport capacity of BBMVs, and higher intestinal villus were detected in the proximal and mid intestine, compared to the distal part. Taken together, our study indicated that intestinal glucose absorption in carp was primarily occurred in the proximal and mid intestine, and increasing levels of dietary glucose and NaCl enhanced intestinal glucose absorption in carp. Copyright © 2017 Elsevier Inc. All rights reserved.

The Influence of Salt Water on Chloride Penetration in Geopolymer Concrete

Directory of Open Access Journals (Sweden)

Halim Like Novia

2017-01-01

Full Text Available This paper presents the influence of chloride ion penetration in geopolymer concrete. Fly ash as based material for geopolymer concrete was used in this mixture. Fly ash was mixed with sodium hydroxide (NaOH 8 M and sodium silicate (Na2SiO3 as the alkali solution. The sizes of cylindrical specimens were prepared with a diameter of 100 mm and 200 mm high. Some specimens were immersed in salt water at a concentration of 3.5%, and other control specimens were cured in tap water for 30, 60, 90, and 120 days. The mechanical properties were determined with compressive test which was conducted at 28, 30, 60, 90 and 120 days. Some durability tests were performed for porosity, chloride penetration, and pH measurement. It was found that geopolymer concrete has higher compressive strength than concrete made with Ordinary Portland cement (OPC. However, chloride penetration in geopolymer concrete is higher than OPC. The pH measurement showed that geopolymer concrete has less pH than OPC concrete. The porosity of concrete has been found to influence chloride penetration and pH of concrete.

Effect of heat treatment on pitting corrosion of austenitic Cr-Ni-Mo steels in sodium chloride solution

International Nuclear Information System (INIS)

Stefec, R.; Franz, F.; Holecek, A.

1979-01-01

The pitting corrosion resistance of Cr17Ni12Mo2,5 type steel under potentiostatic polarization in a sodium chloride solution is adversely affected by previous annealing. The data obtained were systematically dependent on annealing temperature, time and surface roughness. The corrosion current, the number of pits or the mean area of pit opening and the corrosion rate within the pits were increased by previous annealing at 550 to 750 0 C for 1-100 hrs. The highest corrosion rate estimated corresponded to heat treatments provoking severe sensitization to intergranular corrosion. The paercentage area of corrosion pit openings and the estimated pit penetration rates were several times higher for as-machined than for polished surfaces. It can be assumed that pitting corrosion is little affected by the carbon content and that molybdenum depletion of grain-boundary zones is responsible for the reduced pitting resistance of annealed steels. (orig./HP) [de

A method for the manufacture of nuclear-purity sodium

International Nuclear Information System (INIS)

Besson, Paul; Graff, Willy.

1973-01-01

Description is given of a method for the manufacture of sodium from the amalgam provided by sodium chloride aqueous electrolysis cells, comprising the steps of treating the sodium amalgam by a sodium polysulfide or a mixture of sodium polysulfide in anhydrous alcohol solution, then causing the thus obtained sodium monosulfide to react with a polysulfide or a mixture of polysulfides so as to obtain a mixture of sodium polysulfides with a higher sodium content, and finally separating sodium through the electrolysis of the sodium-rich polysulfides, the electrolysis being carried out in an electrolytic cell with β-alumina solid electrolyte operating at a temperature between 250 and 300 deg C, in which the polysulfide forms the anode compartment and sodium the cathode compartment [fr

Ancylostoma caninum: calibration and comparison of diagnostic accuracy of flotation in tube, McMaster and FLOTAC in faecal samples of dogs.

Science.gov (United States)

Cringoli, Giuseppe; Rinaldi, Laura; Maurelli, Maria Paola; Morgoglione, Maria Elena; Musella, Vincenzo; Utzinger, Jürg

2011-05-01

We performed a calibration of flotation in tube, McMaster and FLOTAC to determine the optimal flotation solution (FS) and the influence of faecal preservation for the diagnosis of Ancylostoma caninum in dogs, and compared the accuracy of the three copromicroscopic techniques. Among nine different FS, sodium chloride and sodium nitrate performed best for detection and quantification of A. caninum eggs. Faecal samples, either fresh or preserved in formalin 5%, resulted in higher A. caninum egg counts, compared to frozen samples or preserved in formalin 10% or sodium acetate-acetic acid-formalin. FLOTAC consistently resulted in higher A. caninum eggs per gram of faeces (EPG) and lower coefficient of variation (CV) than McMaster and flotation in tube. The best results in terms of mean faecal egg counts (highest value, i.e. 117.0EPG) and CV (lowest value, i.e. 4.8%) were obtained with FLOTAC using sodium chloride and faecal samples preserved in formalin 5%. Our findings suggest that the FLOTAC technique should be considered for the diagnosis of A. caninum in dogs. Copyright © 2011 Elsevier Inc. All rights reserved.

Efeito do cloreto de sódio na produção de proteínas (Saccharomyces cerevisiae em fermentação semi-sólida Effect of sodium chloride on protein production (Saccharomyces cerevisae by semi-solid fermentation

Directory of Open Access Journals (Sweden)

Ana Maria RODRIGUES

2001-01-01

Full Text Available Estudou-se o efeito do cloreto de sódio sobre a produção de biomassa e proteínas extracelulares totais, durante o cultivo de Saccharomyces cerevisiae. A levedura foi desenvonvida em fermentador de leito fluidizado, com vazão de ar de 70L/min, temperatura de 33° C, e umidade relativa de 99-100%. Foi utilizado substrato semi-sólido de batatas, previamente hidrolizado, acrescido de cloreto de sódio 0,6M. O crescimento celular foi monitorado por densidade óptica à 595 nm. Observou-se, como resultado, que a adição de cloreto de sódio 0,6M induziu um aumento de 36,86% na produção de proteínas extracelulares totais, mas inibiu o crescimento celular em 27,62% quando os meios com e sem cloreto de sódio foram testados. A produção máxima de biomassa, tanto para os experimentos com adição de cloreto de sódio quanto para o sem adição, ocorreu no período de 7 a 9 horas de fermentacão, enquanto que a produção de proteínas extracelulares totais, independentemente da adição do sal, ocorreu durante o período de 9 a 12 horas de fermentação. As velocidades específicas máximas de crescimento foram de 0,350/h para os experimentos com sal, e de 0,339/h para aqueles sem a adição do sal. A combinação de alta vazão de ar e a presença de cloreto de sódio 0,6M na fermentação parece não ter tido efeito sobre a duração da fase lag na curva de crescimento celular de Saccharomyces cerevisiae.The effect of sodium chloride on the cell's growth and total extracellular protein production during fermentation of Saccharomyces cerevisiae in an air-fluidized bed fermentation, with a 70 L/min air flow at 33° C and 99-100% relative unidity was studied. A semi-solid potato substrate (previously hydrolized with 0.6M sodium chloride was used. Cell's growth was monitored by optical density at 595 nm. Results showed that the addition of 0.6M sodium chloride enhanced total extracellular protein level (36.86%. On the other hand, the addition of

Interaction between dietary content of protein and sodium chloride on milk urea concentration, urinary urea excretion, renal recycling of urea, and urea transfer to the gastrointestinal tract in dairy cows

NARCIS (Netherlands)

Spek, J.W.; Bannink, A.; Gort, G.; Hendriks, W.H.; Dijkstra, J.

2013-01-01

Dietary protein and salt affect the concentration of milk urea nitrogen (MUN; mg of N/dL) and the relationship between MUN and excretion of urea nitrogen in urine (UUN; g of N/d) of dairy cattle. The aim of the present study was to examine the effects of dietary protein and sodium chloride (NaCl)

Structural, electrical and optical properties of indium chloride doped ZnO films synthesized by Ultrasonic Spray Pyrolysis technique

International Nuclear Information System (INIS)

Zaleta-Alejandre, E.; Camargo-Martinez, J.; Ramirez-Garibo, A.; Pérez-Arrieta, M.L.; Balderas-Xicohténcatl, R.; Rivera-Alvarez, Z.; Aguilar-Frutis, M.; Falcony, C.

2012-01-01

Indium chloride doped zinc oxide (ZnO:In) thin films were deposited onto glass substrates using zinc acetate by Ultrasonic Spray Pyrolysis technique. The effect of substrate temperature, deposition time and acetic acid added to the spraying solution on the structural, electrical and optical properties of these ZnO:In films is reported. The films were in all cases polycrystalline with a hexagonal (wurtzite) structure, a transparency over 80% and resistivity of the order of 10 −3 –10 −2 Ω·cm. The resistivity was dependent on the volume % of acetic acid added to the spraying solution. The minimum resistivity value was obtained with a 5 vol.% acetic acid (pH = 3.71) at substrate temperature of 450 °C. The deposition rates obtained were as high as 180 Å·min −1 at a substrate temperature of 450 °C. - Highlights: ► Conductive ZnO:In thin films were deposited by Ultrasonic Spray Pyrolysis (USP). ► USP is of low cost, high growth rates and scalable for industrial applications. ► USP is appropriate for the deposition of metallic oxide films. ► We studied the effect of acetic acid, time deposition and substrate temperature. ► Zinc acetate and indium chloride were used as precursor materials.

Method for the preparation of cellulose acetate flat sheet composite membranes for forward osmosis—Desalination using MgSO4 draw solution

KAUST Repository

Sairam, M.; Sereewatthanawut, E.; Li, K.; Bismarck, A.; Livingston, A.G.

2011-01-01

A lab scale method for the preparation of defect free flat sheet composite membranes for forward osmosis (FO) has been developed. Membranes containing a thin layer of cellulose acetate (CA) cast on a nylon fabric of 50μm thick were prepared by phase inversion in water. Cellulose acetate (CA) membranes with an overall thickness of 70-80μm have been prepared with lactic acid, maleic acid and zinc chloride as pore forming agents, at different annealing temperatures, for forward osmosis. These membranes have been tested in the desalination of saline feeds (35g·L-1 of NaCl) using magnesium sulphate solution (150g·L-1) as the draw solution. The water flux, and rejection of NaCl, were compared with those of commercially available membranes tested under the same FO conditions. The commercially available FO membrane from Hydration Technologies Inc, OR (M1) has a permeability of 0.13L·h-1·m-2·bar-1 with a NaCl rejection of 97% when tested with 150g·L-1 of MgSO4 in the draw solution. Another commercially available membrane for FO from Hydration Technologies Inc, OR, M2 has a water permeability of 0.014L·h-1·m-2·bar-1 with NaCl rejection of 100%. The flux and rejection of the CA membranes prepared in this work are found to be dependent on the nature of the pore forming agent, and annealing temperature. Impregnation of an inorganic filler, sodium montmorrillonite in CA membranes and coating of CA membranes with hydrophilic PVA did not enhance the flux of base CA membranes. Cellulose acetate membranes cast from dope solutions containing acetone/isopropanol and lactic acid, maleic acid and zinc chloride as pore forming agents have water permeabilities of 0.13, 0.09 and 0.68L·h-1·m-2·bar-1 respectively, with NaCl rejections of 97.7, 99.3 and 88% when annealed at 50°C. CA membranes prepared with zinc chloride as a pore forming agent have good permeability of 0.27L·h-1·m-2·bar-1 with a NaCl rejection of 95% when annealed at 70°C. © 2011.

Method for the preparation of cellulose acetate flat sheet composite membranes for forward osmosis—Desalination using MgSO4 draw solution

KAUST Repository

Sairam, M.

2011-06-01

A lab scale method for the preparation of defect free flat sheet composite membranes for forward osmosis (FO) has been developed. Membranes containing a thin layer of cellulose acetate (CA) cast on a nylon fabric of 50μm thick were prepared by phase inversion in water. Cellulose acetate (CA) membranes with an overall thickness of 70-80μm have been prepared with lactic acid, maleic acid and zinc chloride as pore forming agents, at different annealing temperatures, for forward osmosis. These membranes have been tested in the desalination of saline feeds (35g·L-1 of NaCl) using magnesium sulphate solution (150g·L-1) as the draw solution. The water flux, and rejection of NaCl, were compared with those of commercially available membranes tested under the same FO conditions. The commercially available FO membrane from Hydration Technologies Inc, OR (M1) has a permeability of 0.13L·h-1·m-2·bar-1 with a NaCl rejection of 97% when tested with 150g·L-1 of MgSO4 in the draw solution. Another commercially available membrane for FO from Hydration Technologies Inc, OR, M2 has a water permeability of 0.014L·h-1·m-2·bar-1 with NaCl rejection of 100%. The flux and rejection of the CA membranes prepared in this work are found to be dependent on the nature of the pore forming agent, and annealing temperature. Impregnation of an inorganic filler, sodium montmorrillonite in CA membranes and coating of CA membranes with hydrophilic PVA did not enhance the flux of base CA membranes. Cellulose acetate membranes cast from dope solutions containing acetone/isopropanol and lactic acid, maleic acid and zinc chloride as pore forming agents have water permeabilities of 0.13, 0.09 and 0.68L·h-1·m-2·bar-1 respectively, with NaCl rejections of 97.7, 99.3 and 88% when annealed at 50°C. CA membranes prepared with zinc chloride as a pore forming agent have good permeability of 0.27L·h-1·m-2·bar-1 with a NaCl rejection of 95% when annealed at 70°C. © 2011.

Changes of free, soluble conjugated and bound polyamine titers of jojoba explants under sodium chloride salinity in vitro.

Science.gov (United States)

Roussos, Peter A; Pontikis, Constantine A

2007-07-01

Jojoba (Simmondsia chinensis L.) single node explants were cultured in a basal medium supplemented with 17.8 microM 6-benzyladenine and four levels of sodium chloride concentration (0, 56.41, 112.82 and 169.23 mM). The free, the soluble conjugated and the insoluble bound forms of polyamines (PAs) (putrescine (Put), spermidine (Spd) and spermine (Spm)) were determined monthly during a 3-month proliferation stage. Free Put and Spd were found in higher levels in the control treatment, while Spm content was higher in the salt treatments. All soluble conjugated PAs were found to be in lower concentrations in explants growing on medium supplemented with salt, while the opposite was true for the insoluble bound PAs. It appeared that certain PAs and PAs forms could play a significant role in the adaptation mechanism of jojoba under saline conditions.

WATER AND SODIUM CHLORIDE EFFECTS ON Mimosa Tenuiflora (WILLD. POIRET SEED GERMINATION

Directory of Open Access Journals (Sweden)

Ivonete Alves Bakke

2006-01-01

Full Text Available Water shortage and saline soils of the Brazilian semi-arid northeastern region are limiting factors to the development of many plants. Jurema preta (Mimosa tenuiflora (Willd. Poiret is a small, multiple use tree that abundantly colonizes unfavorable sites, including environments with severe water stress. This work had the objective of investigating the tolerance of jurema preta seeds to water and salt stresses during germination. Seeds germination in polyethylene glycol (PEG-6000 and sodium chloride (NaCl solutions was analyzed under five different osmotic potentials (0.0; -0.3, -0.6, -0.9 and -1.2MPa, in order to simulate water and salt stress, respectively, in four 100-seed replications for each treatment. Seeds were placed into 10cmx10cmx4cm boxes, and germination accomplished in BOD germinator adjusted to 30oC. The number of germinated seeds was monitored every 24 hours, and percentage and speed of seed germination were generated from these data. Mean percentage germination in the control treatment was ~95%, reducing to 63-53% at -0.9 to -1.2-MPa PEG solutions, and to 27- 9.5% at NaCl solutions at equivalent osmotic potentials. Velocity of germination index was more affected, and decreased up to 1/8 of the control, at -0.6 MPa. Jurema preta seeds showed lower tolerance to NaCl than to water stress, and this species can be classified as a glycophyte.

Coulometric sodium chloride removal system with Nafion membrane for seawater sample treatment.

Science.gov (United States)

Grygolowicz-Pawlak, Ewa; Sohail, Manzar; Pawlak, Marcin; Neel, Bastien; Shvarev, Alexey; de Marco, Roland; Bakker, Eric

2012-07-17

Seawater analysis is one of the most challenging in the field of environmental monitoring, mainly due to disparate concentration levels between the analyte and the salt matrix causing interferences in a variety of analytical techniques. We propose here a miniature electrochemical sample pretreatment system for a rapid removal of NaCl utilizing the coaxial arrangement of an electrode and a tubular Nafion membrane. Upon electrolysis, chloride is deposited at the Ag electrode as AgCl and the sodium counterions are transported across the membrane. This cell was found to work efficiently at potentials higher than 400 mV in both stationary and flow injection mode. Substantial residual currents observed during electrolysis were found to be a result of NaCl back diffusion from the outer side of the membrane due to insufficient permselectivity of the Nafion membrane. It was demonstrated that the residual current can be significantly reduced by adjusting the concentration of the outer solution. On the basis of ion chromatography results, it was found that the designed cell used in flow injection electrolysis mode reduced the NaCl concentration from 0.6 M to 3 mM. This attempt is very important in view of nutrient analysis in seawater where NaCl is a major interfering agent. We demonstrate that the pretreatment of artificial seawater samples does not reduce the content of nitrite or nitrate ions upon electrolysis. A simple diffusion/extraction steady state model is proposed for the optimization of the electrolysis cell characteristics.

Kinetics study of thermal decomposition of sodium carboxylate salts

International Nuclear Information System (INIS)

Landoll, Michael P.; Holtzapple, Mark T.

2012-01-01

The MixAlco™ process ferments lignocellulosic biomass to carboxylate salts that are thermally decomposed into ketones, which are then chemically converted to a wide variety of chemicals and fuels. To perform these decompositions, suitable reaction models are necessary to properly design, scale, and optimize commercial reactors. For three salt types (sodium acetate, and two types of mixed sodium carboxylate salts), activation energy was determined using three isoconversional methods that employed TGA curves at different heating rates. For all three salt types, activation energy varied significantly with conversion. The average activation energy for sodium acetate was 226.65 kJ/mol, and the activation energies for the two mixed sodium carboxylate salts were 195.61, and 218.18 kJ/mol. In addition, three functions of conversion were employed to see which one best modeled the experimental data. The Sestak-Berggren model fits all three salt types best. -- Highlights: ► Sodium carboxylate salts from fermentation broth thermally decompose to ketones. ► Activation energy varies with conversion for all three salt types. ► Sestak-Berggren model provides best fit for all three salt types.

Extraction of silver by gels of sodium poly-acrylic-polyacrylate acid. Application: elimination of chloride anions; Extraction de l'argent par des gels d'acide polyacrylique-polyacrylate de sodium. Application a l'elimination des ions chlorures

Energy Technology Data Exchange (ETDEWEB)

Rifi, E.H. [Universite Ibn-Tofail, Lab. de Synthese Organique et Pocedes d' Extraction, Faculte des Sciences, Kenitra (Morocco); Lakkis, D.; Leroy, J.F.M. [Universite Louis Pasteur, Lab. de Chimie Analytique et Minerale, Ecole Europeenne de Chimie, Polymeres et Materiaux, 67 - Strasbourg (France)

2005-05-01

The extraction of silver from diluted aqueous solutions by gels of sodium poly-acrylic-polyacrylate acid was studied. The study of pH variations shows that the extraction is done by cation-cation exchange process. The highest loading of the gel by silver is obtained at R(moles of Ag{sup +} fixed by the gel/moles of -COO(H, Na))=0.75. The silver gel loaded allows the recovery of ions chlorides from the aqueous solutions. (authors)

Detection of colloidal silver chloride near solubility limit

Science.gov (United States)

Putri, K. Y.; Adawiah, R.

2018-03-01

Detection of nanoparticles in solution has been made possible by several means; one of them is laser-induced breakdown detection (LIBD). LIBD is able to distinguish colloids of various sizes and concentrations. This technique has been used in several solubility studies. In this study, the formation of colloids in a mixed system of silver nitrate and sodium chloride was observed by acoustic LIBD. Silver chloride has low solubility limit, therefore LIBD measurement is appropriate. Silver and chloride solutions with equal concentrations, set at below and above the solubility of silver chloride as the expected solid product, were mixed and the resulting colloids were observed. The result of LIBD measurement showed that larger particles were present as more silver and chloride introduced. However, once the concentrations exceeded the solubility limit of silver chloride, the detected particle size seemed to be decreasing, hence suggested the occurrence of coprecipitation process. This phenomenon indicated that the ability of LIBD to detect even small changes in colloid amounts might be a useful tool in study on formation and stability of colloids, i.e. to confirm whether nanoparticles synthesis has been successfully performed and whether the system is stable or not.

Determination of chloride content in crystalline silicotitanate

International Nuclear Information System (INIS)

Wilmarth, W.R.

1999-01-01

Crystalline Silicotitanate (CST) is one of three options under evaluation to replace the In-Tank Precipitation process. This Salt Disposition Alternatives team identified three options for pretreatment of High Level Waste supernate: non-elutable ion exchange, precipitation with sodium tetraphenylborate or direct disposal in grout. The ion exchange option would use crystalline silicotitanate (CST). Researchers at Texas A and M and Sandia National Laboratory developed CST. The engineered form of CST was procured from UOP LLC under the trade name IONSIVreg s ign IE-911. Review of vendor literature and discussions with UOP personnel led to speculation concerning the fate of chloride ion during the manufacture process of IE-911. Walker proposed tests to examine the chloride content of CST and removal methods. This report describes the results of tests to determine the chloride levels in as received CST and washed CST

Simultaneous identification and quantification by liquid chromatography of benzethonium chloride, methyl paraben and triclosan in commercial products labeled as grapefruit seed extract.

Science.gov (United States)

Avula, B; Dentali, S; Khan, I A

2007-08-01

A HPLC method has been developed which permits the quantification of methyl paraben, benzethonium chloride and triclosan in various samples of grapefruit seed extract (GSE). The best results were obtained with a Phenomenex Gemini C18 column using gradient mobile phase of water (0.1% acetic acid) and acetonitrile (0.1% acetic acid) with a flow rate of 1.0 mL per minute. The detection wavelength was 254 nm for methyl paraben, and 275 nm for benzethonium chloride and triclosan. The main synthetic antimicrobial agent identified in commercial GSE samples was benzethonium chloride in concentrations from 0.29-21.84%. Positive ion electrospray MS of a commercial GSE sample showed a molecular ion at m/z 412 [M+], which matched that of a standard of benzethonium chloride. Triclosan was detected in two samples at 0.009 and 1.13%concentrations; while methyl paraben was not detected in the samples analyzed.

Crystal structures of superconducting sodium intercalates of hafnium nitride chloride

International Nuclear Information System (INIS)

Oro-Sole, J.; Frontera, C.; Beltran-Porter, D.; Lebedev, O.I.; Van Tendeloo, G.; Fuertes, A.

2006-01-01

Sodium intercalation compounds of HfNCl have been prepared at room temperature in naphtyl sodium solutions in tetrahydrofuran and their crystal structure has been investigated by Rietveld refinement using X-ray powder diffraction data and high-resolution electron microscopy. The structure of two intercalates with space group R3-bar m and lattice parameters a=3.58131(6)A, c=57.752(6)A, and a=3.58791(8)A, c=29.6785(17)A is reported, corresponding to the stages 2 and 1, respectively, of Na x HfNCl. For the stage 2 phase an ordered model is presented, showing two crystallographically independent [HfNCl] units with an alternation of the Hf-Hf interlayer distance along the c-axis, according with the occupation by sodium atoms of one out of two van der Waals gaps. Both stages 1 and 2 phases are superconducting with critical temperatures between 20 and 24K, they coexist in different samples with proportions depending on the synthesis conditions, and show a variation in c spacing that can be correlated with the sodium stoichiometry. High-resolution electron microscopy images of the host and intercalated samples show bending of the HfNCl bilayers as well as stacking faults in some regions, which coexist in the same crystal with ordered domains

Thermo-sensitive and swelling properties of cellouronic acid sodium/poly (acrylamide-co-diallyldimethylammonium chloride) semi-IPN.

Science.gov (United States)

Zhang, Heng; Gao, Xin; Chen, Keli; Li, Hui; Peng, Lincai

2018-02-01

In current study, cellouronic acid sodium (CAS), obtained from bagasse pith, has been introduced into poly(acrylamide-co-diallyldimethylammonium chloride) (poly(AM-co-DAC)) network to form novel thermo-sensitive semi-IPNs. The structure and morphology of the hydrogels were proved by Fourier transformation infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The effects of CAS content, initiator charge, cross-linker dosage and swelling-medium property on the thermo-responsive water absorptivity were investigated in detail. The results elucidated that the prepared gels exhibited a thermo-sensibility with an upper critical solution temperature (UCST) and a high water-absorbency. And the values of UCST and equilibrium swelling ratio largely depended on the inner structure of the semi-IPNs and the external solvent property. It was also revealed that the swelling process conformed to the Schott's pseudo second order model and diffusion type was non-Fickian diffusion. The value of activation energy for this polyelectrolyte was found to be 8.74kJ/mol. Copyright © 2017 Elsevier Ltd. All rights reserved.

Intratesticular hypertonic sodium chloride solution treatment as a method of chemical castration in cattle.

Science.gov (United States)

Neto, Olmiro Andrade; Gasperin, Bernardo G; Rovani, Monique T; Ilha, Gustavo F; Nóbrega, Janduí E; Mondadori, Rafael G; Gonçalves, Paulo B D; Antoniazzi, Alfredo Q

2014-10-15

Castration of male calves is necessary for trading to facilitate handling and prevent reproduction. However, some methods of castration are traumatic and lead to economic losses because of infection and myiasis. The objective of the present study was to evaluate the efficiency of intratesticular injection (ITI) of hypertonic sodium chloride (NaCl; 20%) solution in male calf castration during the first weeks of life. Forty male calves were allocated to one of the following experimental groups: negative control-surgically castrated immediately after birth; positive control -intact males; G1-ITI from 1- to 5-day old; G2-ITI from 15- to 20-day old; and G3-ITI from 25- to 30-day old. Intratesticular injection induced coagulative necrosis of Leydig cells and seminiferous tubules leading to extensive fibrosis. Testosterone secretion and testicular development were severely impaired in 12-month-old animals from G1 and G2 groups (P<0.05), in which no testicular structure and sperm cells were observed during breeding soundness evaluation. Rectal and scrotal temperatures were not affected by different procedures. In conclusion, ITI of hypertonic NaCl solution induces sterility and completely suppresses testosterone secretion when performed during the first 20 days of life. Copyright © 2014 Elsevier Inc. All rights reserved.

Titanocene(III) chloride mediated radical induced addition ...

Indian Academy of Sciences (India)

Reduction of the aldehyde 10 with sodium boro- hydride in the presence of CeCl3.7H2O furnished the alcohol 11 which was finally brominated using PBr3 to yield the dibromo compound 12.13. Thus, a series of bromoepoxides were prepared and subjected to radical cyclization using titanocene(III) chloride and the results ...

Conductivity of Cellulose Acetate Membranes from Pandan Duri Leaves (Pandanus tectorius for Li-ion Battery

Directory of Open Access Journals (Sweden)

Laksono Endang W.

2016-01-01

Full Text Available The purpose of this research is to know the influence of lithium chloride composition on membrane conductivity. Cellulose was extracted from pandan duri leaves (P. tectorius by dilute alkaline and bleaching with 0.5% NaOCl followed by synthesis of cellulose acetate using acetic anhydride as acetylating agent, acetic acid as solvent and sulfuric acid as catalyst. The membranes were prepared by casting polymer solution method and the composition of CA/LiCl were 60/40, 65/35, 70/30, 75/25, 80/20 and 100/0. Structural analysis was carried out by FTIR and X-ray diffraction. The conductivity was measured using Elkahfi 100. The highest conductivity of cellulose acetate membrane was 2.20 × 10-4 S cm-1 that measured at room temperature for 65/35 composition

Structural, electrical and optical properties of indium chloride doped ZnO films synthesized by Ultrasonic Spray Pyrolysis technique

Energy Technology Data Exchange (ETDEWEB)

Zaleta-Alejandre, E., E-mail: ezaleta@fis.cinvestav.mx [Centro de Investigacion y de Estudios Avanzados-IPN, Departamento de Fisica, Apdo, Postal 14-470, Del. Gustavo A. Madero, C.P. 07000, Mexico, D.F. (Mexico); Camargo-Martinez, J.; Ramirez-Garibo, A. [Centro de Investigacion y de Estudios Avanzados-IPN, Departamento de Fisica, Apdo, Postal 14-470, Del. Gustavo A. Madero, C.P. 07000, Mexico, D.F. (Mexico); Perez-Arrieta, M.L. [Universidad Autonoma de Zacatecas, Unidad Academica de Fisica, Calzada Solidaridad esq. Paseo, La Bufa s/n, C.P. 98060, Zacatecas, Mexico (Mexico); Balderas-Xicohtencatl, R.; Rivera-Alvarez, Z. [Centro de Investigacion y de Estudios Avanzados-IPN, Departamento de Fisica, Apdo, Postal 14-470, Del. Gustavo A. Madero, C.P. 07000, Mexico, D.F. (Mexico); Aguilar-Frutis, M. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada-IPN, Legaria 694, Col. Irrigacion, Del. Miguel Hidalgo, Mexico, D.F. (Mexico); Falcony, C. [Centro de Investigacion y de Estudios Avanzados-IPN, Departamento de Fisica, Apdo, Postal 14-470, Del. Gustavo A. Madero, C.P. 07000, Mexico, D.F. (Mexico)

2012-12-01

Indium chloride doped zinc oxide (ZnO:In) thin films were deposited onto glass substrates using zinc acetate by Ultrasonic Spray Pyrolysis technique. The effect of substrate temperature, deposition time and acetic acid added to the spraying solution on the structural, electrical and optical properties of these ZnO:In films is reported. The films were in all cases polycrystalline with a hexagonal (wurtzite) structure, a transparency over 80% and resistivity of the order of 10{sup -3}-10{sup -2} Ohm-Sign {center_dot}cm. The resistivity was dependent on the volume % of acetic acid added to the spraying solution. The minimum resistivity value was obtained with a 5 vol.% acetic acid (pH = 3.71) at substrate temperature of 450 Degree-Sign C. The deposition rates obtained were as high as 180 A{center_dot}min{sup -1} at a substrate temperature of 450 Degree-Sign C. - Highlights: Black-Right-Pointing-Pointer Conductive ZnO:In thin films were deposited by Ultrasonic Spray Pyrolysis (USP). Black-Right-Pointing-Pointer USP is of low cost, high growth rates and scalable for industrial applications. Black-Right-Pointing-Pointer USP is appropriate for the deposition of metallic oxide films. Black-Right-Pointing-Pointer We studied the effect of acetic acid, time deposition and substrate temperature. Black-Right-Pointing-Pointer Zinc acetate and indium chloride were used as precursor materials.

Sodium Thiosulfate for Recovery of Bond Strength to Dentin Treated with Sodium Hypochlorite.

Science.gov (United States)

Pimentel Corrêa, Ana Carolina; Cecchin, Doglas; de Almeida, José Flávio Affonso; Gomes, Brenda Paula Figueiredo de Almeida; Zaia, Alexandre Augusto; Ferraz, Caio Cezar Randi

2016-02-01

The aim of this study was to evaluate the efficacy of sodium thiosulfate (Na2S2O3) for restoring adhesion to pulp chamber dentin treated with sodium hypochlorite (NaOCl) and EDTA. Sixty-three crowns of bovine incisors were cut to expose the dentin pulp chamber. The specimens were polished and randomly distributed into 9 groups (n = 7) according to the following protocols used: 0.9% sodium chloride for 30 minutes (negative control), 5.25% NaOCl for 30 minutes, 17% EDTA for 3 minutes, and 5.25% NaOCl for 1 minute (positive control). The other groups, after treatments with NaOCl and EDTA, were immersed in 0.5% or 5% Na2S2O3 for 1, 5, and 10 minutes or just immersed in an inert solution for 10 minutes (0.9% sodium chloride). After drying the specimens, Scotchbond Multi-Purpose (3M ESPE, St Paul, MN) was applied to the pulp chamber dentin followed by Filtek Z250 composite (3M ESPE). Six rectangular slabs were obtained from each specimen, and the dentin/resin interface was tested by using a universal testing machine. The resulting data were submitted to 1-way analysis of variance and the Duncan test (P = .05). There was a significant decrease in bond strength regarding NaOCl and EDTA (P adhesive restorations to be immediately applied after endodontic treatment. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Study of electrochemical behaviour of tantalum in molten alkali metal chlorides

International Nuclear Information System (INIS)

Bajmakov, A.N.; Ezrokhina, A.M.; Sashinina, O.A.; Shkol'nikov, S.N.

1985-01-01

Equilibrium potentials of metallic tantalum in the melt TaCl 5 +KCl-NaCl are studied. Are average degree of tantalum ion oxidation, which are in equilibrium with metallic tantalum, is determined. Anodic behaviour of tantalum in equimolar mixture of potassium and sodium chlorides with Ta and F ion additions is considered. An average degree of oxidation of Ta ions, which transfer into the melt, depending on current density, is determined. It is established that tantalum is dissolved in the regime of diffusional kinetics. It is shown that tantalum corrodes in equimolar mixture of potassium and sodiUm chlorides, at that, corrosion rate increases with introdUction of Ta and F ions into solution. The corrosion is of electrochemical nature and it proceeds in the regime of diffusional kinetics

Improved adaptation of test with lanthanum nitrate for the colorimetric estimation of acetate

Energy Technology Data Exchange (ETDEWEB)

Szumilo, T [Akademia Medyczna, Lublin (Poland)

1976-01-01

A colorimetric method for the determination of acetate based on the production of the blue complex between iodine and lanthanum alkaline acetate has been developed. Optimum concentrations of reagents (acetate, lanthanum nitrate, iodine and ammonia) as well as the volume of acetate were selected to achieve best colour intensity. Coloured complex was stabilized by dilution of reagent mixture with water to the final volume convenient for determinaton. Absorbance of the complex can be measured immediately after dilution and any changes can be observed during at least 15 minutes. Elevation of temperature over 60/sup 0/decreases absorbance. The method fulfills the Beer's law in the range 1,5-3,5 ..mu..moles of acetate, precision of the method 2/sup +/ = 3,7%. Apart from acetate - propionate and fluoroacetate complex is 620 nm, propionate complex - at 590 nm. Propionate complex displayed any relationship between concentration and absorbance. Potassium, sodium, lithium and barium acetates give the identical results as acetic acid, whereas zinc and cupric acetates failed to react. Other derivatives tested, e.g. chloroacetate, trichloroacetate, iodoacetate, chloroporpionate and butyrate are unable to form the coloured complexes. Many compounds interfere with the formation of acetate complex, therefore, in material containing impurities acetate can be determined after purificaton by means of described in literature methods.

Electrolytic production of light lanthanides from molten chloride alloys on a large laboratory scale

International Nuclear Information System (INIS)

Szklarski, W.; Bogacz, A.; Strzyzewska, M.

1979-01-01

Literature data relating to electrolytic production of rare earth metals are presented. Conditions and results are given of own investigations into the electrolytic process of light lanthanide chloride solutions (LA-Nd) in molten potassium and sodium chlorides conducted on a large laboratory scale using molybdenic, iron, cobaltic and zinc cathodes. Design schemes of employed electrolysers are enclosed. (author)

Liquid-liquid extraction/separation of platinum(IV) and rhodium(III) from acidic chloride solutions using tri-iso-octylamine

Energy Technology Data Exchange (ETDEWEB)

Lee, Jin-Young, E-mail: jinlee@kigam.re.kr [Metals Recovery Department, Minerals Resources Research Division, Korea Institute of Geoscience and Mineral Resources (KIGAM), 92 Gahangno, Yuesong-gu, Daejeon 305-350 (Korea, Republic of); Rajesh Kumar, J., E-mail: rajeshkumarphd@rediffmail.com [Metals Recovery Department, Minerals Resources Research Division, Korea Institute of Geoscience and Mineral Resources (KIGAM), 92 Gahangno, Yuesong-gu, Daejeon 305-350 (Korea, Republic of); Kim, Joon-Soo; Park, Hyung-Kyu; Yoon, Ho-Sung [Metals Recovery Department, Minerals Resources Research Division, Korea Institute of Geoscience and Mineral Resources (KIGAM), 92 Gahangno, Yuesong-gu, Daejeon 305-350 (Korea, Republic of)

2009-08-30

Liquid-liquid extraction/separation of platinum(IV) and rhodium(III) from acidic chloride solutions was carried out using tri-iso-octylamine (Alamine 308) as an extractant diluted in kerosene. The percentage extraction of platinum(IV) and rhodium(III) increased with increase in acid concentration up to 8 mol L{sup -1}. However, at 10 mol L{sup -1} HCl concentration, the extraction behavior was reversed, indicating the solvation type mechanism during extraction. The quantitative extraction of {approx}98% platinum(IV) and 36% rhodium(III) was achieved with 0.01 mol L{sup -1} Alamine 308. The highest separation factor (S.F. = 184.7) of platinum(IV) and rhodium(III) was achieved with 0.01 mol L{sup -1} Alamine 308 at 1.0 mol L{sup -1} of hydrochloric acid concentration. Alkaline metal salts like sodium chloride, sodium nitrate, sodium thiocyanate, lithium chloride, lithium nitrate, potassium chloride and potassium thiocyanate used for the salting-out effect. LiCl proved as best salt for the extraction of platinum(IV). Temperature effect demonstrates that the extraction process is exothermic. Hydrochloric acid and thiourea mixture proved to be better stripping reagents when compared with other mineral acids and bases.

Attachment of 13 Types of Foodborne Bacteria to Jalapeño and Serrano Peppers and Antibacterial Effect of Roselle Calyx Extracts, Sodium Hypochlorite, Colloidal Silver, and Acetic Acid against These Foodborne Bacteria on Peppers.

Science.gov (United States)

Rangel-Vargas, Esmeralda; Gómez-Aldapa, Carlos A; Falfan-Cortes, Reyna N; Rodríguez-Marín, María L; Godínez-Oviedo, Angélica; Acevedo-Sandoval, Otilio A; Castro-Rosas, Javier

2017-03-01

Chili peppers are a very important crop in Mexico. However, these peppers have been associated with Salmonella infection outbreaks in the United States, and Salmonella and diarrheagenic Escherichia coli pathotypes have been isolated from jalapeño and serrano peppers in Mexico. To decrease microbial contamination of fruits and vegetables, chemical agents are commonly used; however, chemical agents used to eliminate pathogenic bacteria on vegetables have a limited antimicrobial effect. Roselle ( Hibiscus sabdariffa ) calyces have been reported to have an antimicrobial effect on pathogenic bacteria. In the present study, the antibacterial effect of four roselle calyx extracts (water, methanol, acetone, and ethyl acetate), sodium hypochlorite, colloidal silver, and acetic acid against foodborne bacteria was evaluated on contaminated jalapeño and serrano peppers. The 13 types of foodborne bacteria evaluated were Listeria monocytogenes , Shigella flexneri , Salmonella Typhimurium, Salmonella Typhi, Salmonella Montevideo, Staphylococcus aureus , E. coli O157:H7, five E. coli pathotypes (Shiga toxin producing, enteropathogenic, enterotoxigenic, enteroinvasive, and enteroaggregative), and Vibrio cholerae O1. All 13 types attached to both pepper types, with no significant differences in attachment between jalapeño and serrano peppers. Roselle calyx extract treatment resulted in a greater reduction in levels of all foodborne bacteria than did treatment with sodium hypochlorite, colloidal silver, and acetic acid on both pepper types. Roselle calyx extracts may be a useful for disinfection of chili peppers in the field, processing plants, restaurants, and homes.

DFT-Based Explanation of the Effect of Simple Anionic Ligands on the Regioselectivity of the Heck Arylation of Acrolein Acetals

DEFF Research Database (Denmark)

Henriksen, Signe Teuber; Tanner, David Ackland; Cacchi, Sandro

2009-01-01

The Heck arylation of acrolein acetal has been studied computationally and compared to the corresponding reaction with allyl ethers. The reaction can be controlled to give either cinnamaldehydes or arylpropanoic esters by addition of different coordinating anions, acetate, or chloride. The comput...... reaction conditions. The difference between the two substrate classes could be rationalized in terms of relative hydride donating power of the two substrates....

Chloride stress corrosion cracking of Alloy 600 in boric acid solutions

International Nuclear Information System (INIS)

Berge, Ph.; Noel, D.; Gras, J.M.; Prieux, B.

1997-10-01

The high nickel austenitic alloys are generally considered to have good resistance to chloride stress corrosion cracking. In the standard boiling magnesium chloride solution tests, alloys with more than 40% nickel are immune. Nevertheless, more recent data show that cracking can occur in both Alloys 600 and 690 if the solution is acidified. In other low pH media, such as boric acid solution at 100 deg C, transgranular and intergranular cracking are observed in Alloy 600 in the presence of minor concentrations of sodium chloride (2g/I). In concentrated boric acid at higher temperatures (250 and 290 deg C), intergranular cracking also occurs, either when the chloride concentration is high, or at low chloride contents and high oxygen levels. The role of pH and a possible specific action of boric acid are discussed, together with the influence of electrochemical potential. (author)

Contribution of chloride channel permease to fluoride resistance in Streptococcus mutans.

Science.gov (United States)

Murata, Takatoshi; Hanada, Nobuhiro

2016-06-01

Genes encoding fluoride transporters have been identified in bacterial and archaeal species. The genome sequence of the cariogenic Streptococcus mutans bacteria suggests the presence of a putative fluoride transporter, which is referred to as a chloride channel permease. Two homologues of this gene (GenBank locus tags SMU_1290c and SMU_1289c) reside in tandem in the genome of S. mutans The aim of this study was to determine whether the chloride channel permeases contribute to fluoride resistance. We constructed SMU_1290c- and SMU_1289c-knockout S. mutans UA159 strains. We also constructed a double-knockout strain lacking both genes. SMU_1290c or SMU_1289c was transformed into a fluoride transporter- disrupted Escherichia coli strain. All bacterial strains were cultured under appropriate conditions with or without sodium fluoride, and fluoride resistance was evaluated. All three gene-knockout S. mutans strains showed lower resistance to sodium fluoride than did the wild-type strain. No significant changes in resistance to other sodium halides were recognized between the wild-type and double-knockout strains. Both SMU_1290c and SMU_1289c transformation rescued fluoride transporter-disrupted E. coli cell from fluoride toxicity. We conclude that the chloride channel permeases contribute to fluoride resistance in S. mutans. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Determination of indium(III) with 3,4,5,6-tetrachlorogallein and cetylpyridinium chloride

International Nuclear Information System (INIS)

Mori, Itsuo; Fujita, Yoshikazu; Ida, Masako; Enoki, Takehisa

1976-01-01

Rapid and highly sensitive methods have been developed for the spectrophotometric and titrimetric determination of indium(III) with 3,4,5,6-tetrachlorogallein(3,4,5,6-T. Cl, Gal.) and cetylpyridinium chloride(CPC) in aqueous solutions of pH 4.2--5.2. The absorbance of the indium(III)-3,4,5,6-T. Cl. Gal. complex at 620 nm and the color change (pure blue - weak violetish red) were used to indicate the end point in the EDTA titration. The calibration curve for the spectrophotometry was linear in the range 0--45.0 μg In(III)/10 ml. According to Sandell's expression, the sensitivity was 0.0032 μg In(III)/cm 2 for an absorbance of 0.001. To the solution containing less than 45.0 μg of indium(III), 2.0 ml of 1.0x10 -2 M CPC solution, 3.0 ml of Walpole buffer solution(pH 4.4; acetic acid-sodium acetate), and 2.0 ml of 1.0x10 -3 M 3,4,5,6-T.Cl.Gal. methanol solution were added and the volume was made up to 10.0 ml with water. The solution was kept at (20--25) 0 C for 30 minutes and then the absorbance was measured at 620 nm against the reagent blank. The mole ratio of indium(III), 3,4,5,6-T.Cl.Gal. and CPC in the complex was estimated to be 1 : 2 : 2 by the continuous variation and the mole ratio methods. (auth.)

Compressive strength, chloride permeability, and freeze-thaw resistance of MWNT concretes under different chemical treatments.

Science.gov (United States)

Wang, Xingang; Rhee, Inkyu; Wang, Yao; Xi, Yunping

2014-01-01

This study investigated compressive strength, chloride penetration, and freeze-thaw resistance of multiwalled carbon nanotube (MWNT) concrete. More than 100 cylindrical specimens were used to assess test variables during sensitivity observations, including water-cement ratios (0.75, 0.5, and 0.4) and exposure to chemical agents (including gum arabic, propanol, ethanol, sodium polyacrylate, methylcellulose, sodium dodecyl sulfate, and silane). To determine the adequate sonication time for MWNT dispersal in water, the compressive strengths of MWNT concrete cylinders were measured after sonication times ranging from 2 to 24 minutes. The results demonstrated that the addition of MWNT can increase the compressive strength of concrete by up to 108%. However, without chemical treatment, MWNT concretes tend to have poor freeze-thaw resistance. Among the different chemical treatments, MWNT concrete treated with sodium polyacrylate has the best compressive strength, chloride resistance, and freeze-thaw durability.

Differential gene expression and filamentation of Listeria monocytogenes 08-5923 exposed to sodium lactate and sodium diacetate.

Science.gov (United States)

Liu, Xiaoji; Basu, Urmila; Miller, Petr; McMullen, Lynn M

2017-05-01

This study reports the gene expression and filamentation in Listeria monocytogenes 08-5923 following exposure to food preservatives sodium lactate (NaL) and sodium diacetate (SD). L. monocytogenes 08-5923 was challenged with a mixture of NaL/SD, NaL or sodium acetate at 37 °C in tryptic soy broth. In the initial study, L. monocytogenes 08-5923 was exposed to NaL/SD for 24 h. The transcriptome was investigated by RNA sequencing. A stress response network was discovered in L. monocytogenes 08-5923, which is mediated by genes encoding two-component systems (hisJ, lisK, OmpR family gene, resE) and RNA polymerase factors (sigC, sigH). NaL/SD resulted in the down-regulation of genes in glycolysis (pykA, eno, fbaA, pgm) and up-regulation of genes in DNA repair (radC), cell division (ftsE) and cell structure synthesis (flagella synthesis: flgK, fliF, fliD). Filamentation was monitored by flow cytometry. NaL/SD mixture resulted in filamentation in L. monocytogenes 08-5923. Longer exposure was required to induce filamentation in L. monocytogenes for SD (24 h) than for NaL (8 h) when cells were exposed to individual salt. The quantitative real time PCR analysis revealed the down-regulation of ftsE in filamented cells of Listeria exposed to NaL or sodium acetate. Copyright © 2016 Elsevier Ltd. All rights reserved.

Catalytic conversion of corncob and corncob pretreatment hydrolysate to furfural in a biphasic system with addition of sodium chloride.

Science.gov (United States)

Qing, Qing; Guo, Qi; Zhou, Linlin; Wan, Yilun; Xu, Youqing; Ji, Huilong; Gao, Xiaohang; Zhang, Yue

2017-02-01

Catalytic conversion of corncob pretreatment hydrolysate and raw corncob into furfural in a modified biphasic system by SO 4 2- /SnO 2 - MMT solid catalyst has been developed. The influence of the organic solvent type, organic to water phase ratio, sodium chloride concentration, reaction temperature and time on the furfural production were comparatively evaluated. The results showed that furfural yields of 81.7% and 66.1% were achieved at 190°C for 15mins and 190°C for 20mins, respectively, for corncob pretreatment hydrolysate and raw corncob by this solid catalyst. The solid catalyst used in this study exhibited good stability and high efficiency applied in the modified biphasic system in addition to excellent recyclability. The proposed catalytic system displayed high performance for catalytic conversion of lignocellulosic biomass into important platform chemicals and has great potential in industrial application. Copyright © 2016 Elsevier Ltd. All rights reserved.

Substituted sodium phenylanthranylates as inhibitors of corrosion in chloride solutions

International Nuclear Information System (INIS)

Kuznetsov, Yu.I.; Fialkov, Yu.A.; Popova, L.I.; Ehndel'man, E.S.; Kuznetsova, I.G.

1982-01-01

The efficiency of corrosion protoction of armco iron, zinc (Ts-O) aluminium (AB 000) and its alloys (.D16 and AMG6) with sodium phenylanthranylate derivatives in clloride buffer solutions (pH 7.4-8.08) are investigated. It has been ascertained that the introduction of sodium phenylantiranylate into phenyl radical in m- and p-position relative to the amino group of electron-seeking substitutes improves protective properties of an inhibitor. The inhibiting effect of phenylanthranylates and its dependence on electron structure enchances in zinc-aluminium-iron series and decreases in case of transition from pure aluminium to its alloys

Ulipristal acetate versus leuprolide acetate for uterine fibroids.

Science.gov (United States)

Donnez, Jacques; Tomaszewski, Janusz; Vázquez, Francisco; Bouchard, Philippe; Lemieszczuk, Boguslav; Baró, Francesco; Nouri, Kazem; Selvaggi, Luigi; Sodowski, Krzysztof; Bestel, Elke; Terrill, Paul; Osterloh, Ian; Loumaye, Ernest

2012-02-02

The efficacy and side-effect profile of ulipristal acetate as compared with those of leuprolide acetate for the treatment of symptomatic uterine fibroids before surgery are unclear. In this double-blind noninferiority trial, we randomly assigned 307 patients with symptomatic fibroids and excessive uterine bleeding to receive 3 months of daily therapy with oral ulipristal acetate (at a dose of either 5 mg or 10 mg) or once-monthly intramuscular injections of leuprolide acetate (at a dose of 3.75 mg). The primary outcome was the proportion of patients with controlled bleeding at week 13, with a prespecified noninferiority margin of -20%. Uterine bleeding was controlled in 90% of patients receiving 5 mg of ulipristal acetate, in 98% of those receiving 10 mg of ulipristal acetate, and in 89% of those receiving leuprolide acetate, for differences (as compared with leuprolide acetate) of 1.2 percentage points (95% confidence interval [CI], -9.3 to 11.8) for 5 mg of ulipristal acetate and 8.8 percentage points (95% CI, 0.4 to 18.3) for 10 mg of ulipristal acetate. Median times to amenorrhea were 7 days for patients receiving 5 mg of ulipristal acetate, 5 days for those receiving 10 mg of ulipristal acetate, and 21 days for those receiving leuprolide acetate. Moderate-to-severe hot flashes were reported for 11% of patients receiving 5 mg of ulipristal acetate, for 10% of those receiving 10 mg of ulipristal acetate, and for 40% of those receiving leuprolide acetate (P<0.001 for each dose of ulipristal acetate vs. leuprolide acetate). Both the 5-mg and 10-mg daily doses of ulipristal acetate were noninferior to once-monthly leuprolide acetate in controlling uterine bleeding and were significantly less likely to cause hot flashes. (Funded by PregLem; ClinicalTrials.gov number, NCT00740831.).

Micro-syntheses for the use of carbon 13 or carbon 14. Micro-preparations of methyl alcohol, methyl iodide, and sodium acetate labeled in the methyl group; Microsyntheses pour l'emploi de carbone 13 ou de carbone 14. Micropreparations d'alcool methylique, d'iodure de methyle et d'acetate de sodium marque sur le groupement methyle

Energy Technology Data Exchange (ETDEWEB)

Baret, C; Pichat, L

1951-11-01

Apparatus and technique are described in detail for (1) reduction of CO{sub 2} to CH{sub 3}OH with LiAlH{sub 4}, (2) conversion of the methanol to CH{sub 3}I by HI, (3) formation of the Mg Grignard reagent, and (4) addition of inactive CO{sub 2} to form CH{sub 3}COOH. All these operations have been carried out on 0.005 moles. Methyl-labeled Na acetate has been prepared in 67% yield based on the Ba{sup 14}CO{sub 3} used as starting material. (author) [French] Description detaillee d'une technique deja connue pour la reduction du gaz carbonique en alcool methylique par LiAlH{sub 4}. Conversion du methanol en iodure de methyle. Ce dernier transforme en reactif de Grigard, et carbonate, fournit de l'acide acetique. Toutes ces operations on ete effectuees sur 5 x 10{sup -3} moles. La methode a ete appliquee a la synthese d'acetate de sodium marque par le groupement methyle par {sup 14}C avec un rendement global de 67% base sur le carbonate de baryum radioactif mis en oeuvre. (auteurs)

on crude water and sodium chloride extracts of Moringa stenopetala

African Journals Online (AJOL)

AJB SERVER

2006-12-04

Dec 4, 2006 ... coordination or complex formation between the metal cations and pH dependent oxygen and nitrogen anionic sites of the ... iron hydroxide, iron chloride, soda ash and synthetic polymers .... o u n d. Zn adsorption by. MSC-SC. Zn adsorption by. MOC-SC .... Okuda T, Baes AU, Nishijima W, Okada M (2001).

Acetate transiently inhibits myocardial contraction by increasing mitochondrial calcium uptake.

Science.gov (United States)

Schooley, James F; Namboodiri, Aryan M A; Cox, Rachel T; Bünger, Rolf; Flagg, Thomas P

2014-12-09

There is a close relationship between cardiovascular disease and cardiac energy metabolism, and we have previously demonstrated that palmitate inhibits myocyte contraction by increasing Kv channel activity and decreasing the action potential duration. Glucose and long chain fatty acids are the major fuel sources supporting cardiac function; however, cardiac myocytes can utilize a variety of substrates for energy generation, and previous studies demonstrate the acetate is rapidly taken up and oxidized by the heart. In this study, we tested the effects of acetate on contractile function of isolated mouse ventricular myocytes. Acute exposure of myocytes to 10 mM sodium acetate caused a marked, but transient, decrease in systolic sarcomere shortening (1.49 ± 0.20% vs. 5.58 ± 0.49% in control), accompanied by a significant increase in diastolic sarcomere length (1.81 ± 0.01 μm vs. 1.77 ± 0.01 μm in control), with a near linear dose response in the 1-10 mM range. Unlike palmitate, acetate caused no change in action potential duration; however, acetate markedly increased mitochondrial Ca(2+) uptake. Moreover, pretreatment of cells with the mitochondrial Ca(2+) uptake blocker, Ru-360 (10 μM), markedly suppressed the effect of acetate on contraction. Lehninger and others have previously demonstrated that the anions of weak aliphatic acids such as acetate stimulate Ca(2+) uptake in isolated mitochondria. Here we show that this effect of acetate appears to extend to isolated cardiac myocytes where it transiently modulates cell contraction.

Inactivation of Foot-and-Mouth Disease Virus by Citric Acid and Sodium Carbonate with Deicers

Science.gov (United States)

Hong, Jang-Kwan; You, Su-Hwa; Kim, Su-Mi; Tark, Dongseob; Lee, Hyang-Sim; Ko, Young-Joon; Seo, Min-Goo; Park, Jong-Hyeon; Kim, Byounghan

2015-01-01

Three out of five outbreaks of foot-and-mouth disease (FMD) since 2010 in the Republic of Korea have occurred in the winter. At the freezing temperatures, it was impossible to spray disinfectant on the surfaces of vehicles, roads, and farm premises because the disinfectant would be frozen shortly after discharge and the surfaces of the roads or machines would become slippery in cold weather. In this study, we added chemical deicers (ethylene glycol, propylene glycol, sodium chloride, calcium chloride, ethyl alcohol, and commercial windshield washer fluid) to keep disinfectants (0.2% citric acid and 4% sodium carbonate) from freezing, and we tested their virucidal efficacies under simulated cold temperatures in a tube. The 0.2% citric acid could reduce the virus titer 4 logs at −20°C with all the deicers. On the other hand, 4% sodium carbonate showed little virucidal activity at −20°C within 30 min, although it resisted being frozen with the function of the deicers. In conclusion, for the winter season, we may recommend the use of citric acid (>0.2%) diluted in 30% ethyl alcohol or 25% sodium chloride solvent, depending on its purpose. PMID:26319879

Investigation of gel formation and volatilization of acetate acid in magnesium acetate droplets by the optical tweezers.

Science.gov (United States)

Lv, Xi-Juan; Wang, Yang; Cai, Chen; Pang, Shu-Feng; Ma, Jia-Bi; Zhang, Yun-Hong

2018-07-05

Hygroscopicity and volatility of single magnesium acetate (MgAc 2 ) aerosol particles at various relative humidities (RHs) are studied by a single-beam optical tweezers, and refractive indices (RIs) and morphology are characterized by cavity enhanced Raman spectroscopy. Gel formation and volatilization of acetate acid (HAc) in MgAc 2 droplets are observed. Due to the formation of amorphous gel structure, water transposition in droplets at RH magnesium hydroxide (Mg(OH) 2 ) inclusions are formed in MgAc 2 droplets due to the volatilization of HAc, and whispering gallery modes (WGMs) of MgAc 2 droplets in the Raman spectrum quench after 50,000 s. In sharp contrast, after 86,000 s at RH ≈ 70%, NaAc droplets are in well-mixed liquid states, containing soluble sodium hydroxide (NaOH). At this state, the RI of NaAc droplet is increased, and the quenching of WGMs is not observable. Copyright © 2018 Elsevier B.V. All rights reserved.

Fixing of metallic acetates on an anion-exchange resin; Fixation d'acetates metalliques dans une resine echangeuse d'anions

Energy Technology Data Exchange (ETDEWEB)

Brigaudeau-Vaissiere, M [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etude Nucleaires

1966-06-01

After giving a brief review of the theoretical principles governing the fixation of anionic complexes of metallic elements on an anion exchange resin, we consider the particular case of uranyl acetate. By plotting the partition curves we have been able to calculate the exchange constants in the resin. By studying the changes in the logarithm of the limiting partition coefficient as a function of the logarithm of the free acetate ion concentration, it has been possible to calculate the dissociation constants for the complexes in solution. The fixation of a large number of metallic acetates has been studied. All the tests have been negative except in the case of mercury. For this reason we have been able to consider the possibility of separating uranium from a certain number of elements. Some of these separations are possible even in the presence of interfering anions such as chlorides which have a greater affinity for the resin than have the acetate ions. In the case of water-ethanol and water-isopropanol mixtures, we have improved the conditions under which copper acetate and mercury acetate may be fixed. This study has enabled us to calculate the dissociation constant for the CuAc{sub 3}{sup -} complex in the mixtures water +40% (by weight) isopropanol and water +50% (by weight) isopropanol. It should also make it possible to use separation conditions which could not hitherto be applied in aqueous media. (author) [French] Apres avoir rappele les principes theoriques de la fixation des complexes anioniques des elements metalliques dans une resine echangeuse d'anions, nous avons etudie tout particulierement le cas de l'acetate d'uranyle. Le trace des courbes de partage nous a permis de calculer les constantes d'echange dans la resine. L'etude des variations du logarithme du coefficient limite de partage avec le logarithme de la concentration des ions acetate libres nous a conduits aux calculs des constantes de dissociation des complexes en solution. La fixation d

Compressive Strength, Chloride Permeability, and Freeze-Thaw Resistance of MWNT Concretes under Different Chemical Treatments

Directory of Open Access Journals (Sweden)

Xingang Wang

2014-01-01

Full Text Available This study investigated compressive strength, chloride penetration, and freeze-thaw resistance of multiwalled carbon nanotube (MWNT concrete. More than 100 cylindrical specimens were used to assess test variables during sensitivity observations, including water-cement ratios (0.75, 0.5, and 0.4 and exposure to chemical agents (including gum arabic, propanol, ethanol, sodium polyacrylate, methylcellulose, sodium dodecyl sulfate, and silane. To determine the adequate sonication time for MWNT dispersal in water, the compressive strengths of MWNT concrete cylinders were measured after sonication times ranging from 2 to 24 minutes. The results demonstrated that the addition of MWNT can increase the compressive strength of concrete by up to 108%. However, without chemical treatment, MWNT concretes tend to have poor freeze-thaw resistance. Among the different chemical treatments, MWNT concrete treated with sodium polyacrylate has the best compressive strength, chloride resistance, and freeze-thaw durability.

Electrochemical reduction of lanthanum trichloride in a molten equimolar mixture of sodium and potassium chlorides

Energy Technology Data Exchange (ETDEWEB)

Glagolevskaya, A.L.; Kuznetsov, S.A.; Polyakov, E.G.; Stangrit, P.T.

1987-09-20

The authors used linear voltamperometry for the investigation of the mechanism for the cathodic reduction of lanthanum. The mechanism for the cathodic reduction of lanthanum chloride in molten equimolar NaCl-KCl may be seen as consisting of a slow irreversible electrode reaction with a subsequent rapid irreversible chemical reaction. Lanthanum ions in a lower oxidation state were not found upon the prolonged maintenance of metallic lanthanum in molten NaCl-KCl-LaCl/sub 3/. Only an increase in the concentration of lanthanum(III) chloride in the melt was noted. The appearance of oxygen anions in the melt does not lead to a change in the mechanism of the cathodic reduction of lanthanum chloride but reduces the concentration of this chloride due to the formation of lanthanum oxochloride which is insoluble in the melt.

Thermal and dynamic mechanical properties of grafted kenaf filled poly (vinyl chloride)/ethylene vinyl acetate composites

International Nuclear Information System (INIS)

Bakar, Nurfatimah Abu; Chee, Ching Yern; Abdullah, Luqman Chuah; Ratnam, Chantara Thevy; Ibrahim, Nor Azowa

2015-01-01

Highlights: • Study on thermal and dynamic mechanical properties of PVC/EVA/PMMA grafted kenaf fiber. • PMMA grafted kenaf fiber showed good interaction with PVC/EVA blends. • Thermal stability of the composites increase upon PMMA grafting on kenaf fiber. • The crystallinity of the composites decrease upon PMMA grafting on kenaf fiber. • PMMA grafted fiber provides more reinforcement on PVC/EVA/grafted PMMA composite. - Abstract: The effects of kenaf and poly (methyl methacrylate grafted kenaf on the thermal and dynamic mechanical properties of poly (vinyl chloride), PVC and ethylene vinyl acetate, EVA blends were investigated. The PVC/EVA/kenaf composites were prepared by mixing the grafted and ungrafted kenaf fiber and PVC/EVA blend using HAAKE Rheomixer at a temperature of 150 °C and the rotor speed at 50 rpm for 20 min. The composites were subjected to Differential Scanning Calorimetric (DSC), Thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), Fourier transform infrared (FTIR) and Scanning Electron Microscopy (SEM) studies. The DSC data revealed that the crystallinity of the EVA decreased with the addition of 30% grafted and ungrafted kenaf fibers. TGA and derivative thermogravimetric (DTG) curves displayed an increase in the thermal stability of the composites upon grafting of the fiber. Studies on DMA indicate that the T g of the PVC and EVA in the PVC/EVA/kenaf composites has been shifted to higher temperature with the addition of the kenaf fiber. The presence of PMMA on the surface of grafted kenaf fiber was further confirmed by the analytical results from FTIR. The morphology of fractured surfaces of the composites, which was examined by a scanning electron microscope, showed the adhesion between the kenaf fiber and the PVC/EVA matrix was improved upon grafting of the kenaf fiber

Compatibility and stability of aloxi (palonosetron hydrochloride) admixed with dexamethasone sodium phosphate.

Science.gov (United States)

Trissel, Lawrence A; Zhang, Yanping

2004-01-01

The purpose of this study was to evaluate the physical and chemical stability of palonosetron hydrochloride 0.25 mg admixed with dexamethasone (as sodium phophate) 10 mg or 20 mg in 5% dextrose injection or 0.9% sodium chloride injection in polyvinylchloride minibags, and also admixed with dexamethasone (as sodium phosphate) 3.3 mg in 5% dextrose injection or 0.9% sodium chloride injection in polypropylene syringes, at 4 deg C stored in the dark for 14 days, and at 23 deg C exposed to normal laboratory fluorescent light over 48 hours. Test samples of palonosetron hydrochloride 5 micrograms/mL with dexamethasone (as sodium phosphate) 0.2 mg/mL and also 0.4 mg/mL were prepared in polyvinylchloride minibags of each infusion solution. Additionally, palonosetron hydrochloride 25 micrograms/mL with dexamethasone (as sodium phosphate) 0.33 mg/mL in each infusion solution were prepared as 10 mL of test solution in 20-mL polypropylene syringes. Evaluations for physical and chemical stability were performed on samples taken initially and after 1, 3, 7 and 14 days of storage at 4 deg C and after 1, 4, 24 and 48 hours at 23 deg C. Physical stability was assessed using visual observation in normal room light and using a high-intensity monodirectional light beam. In addition, turbidity and particle content were measured electronically. Chemical stability of the drug was evaluated by using a stability-indicating high-performance liquid chromatographic analytical technique. All samples were physically compatible throughout the study. The solutions remained clear and showed little or no change in particulate burden and haze level. Additionally, little or no loss of palonosetron hydrochloride and dexamethasone occurred in any of the samples at either temperature throughout the entire study period. Admixtures of palonosetron hydrochloride with dexamethasone sodium phosphate in 5% dextrose injection or in 0.9% sodium chloride injection packaged in polyvinylchloride minibags or in

Radiation fixation of vinyl chloride in an insecticide aerosol container

International Nuclear Information System (INIS)

Kagiya, V.T.; Takemoto, K.

1975-01-01

Recently, a large quantity of vinyl chloride has been used as spraying additive for insecticide aerosols. Since January 1974 when the Food and Drug Administration of the United States of America announced that vinyl chloride causes liver cancer, it has been forbidden in Japan and the United States of America to market insecticide aerosol containers containing vinyl chloride. In Japan, following a government order, about 20 million insecticide aerosol containers have been collected and put into storage. A report is given on the radiation fixation of vinyl chloride as polyvinylchloride powder by gamma-ray-induced polymerization in the aerosol container. Insecticide aerosol containers containing vinyl chloride were irradiated by gamma rays from 60 Co at room temperature. Vinyl chloride polymerized to form powdered polymer in the container. Polymerization conversion increased with the irradiation dose, and after 10 Mrad irradiation, vinyl chloride was not found in the sprayed gas. This establishes that vinyl chloride can be fixed by gamma-ray irradiation in the aerosol container. To accelerate the reaction rate, the effect of various additives on the reaction was investigated. It was found that halogenated hydrocarbons, such as chloroform and carbon tetrachloride, accelerated the initiation of the polymerization, and that a vinyl monomer such as vinyl acetate accelerated the reaction rate due to the promotion of the initiation and the high reactivity of the polyvinylacetate radical to vinyl chloride. Consequently, the required irradiation dose for the fixation of vinyl chloride was decreased to less than 5 Mrad by the addition of various kinds of additives. Following the request of the Ministry of Public Welfare, various technical problems for large-scale treatment are being studied with the co-operation of the Federation of Insecticide Aerosols. (author)

The Synergistic Effect of Iodide and Sodium Nitrite on the Corrosion Inhibition of Mild Steel in Bicarbonate–Chloride Solution

Directory of Open Access Journals (Sweden)

Gaius Debi Eyu

2016-10-01

Full Text Available The effect of potassium iodide (KI and sodium nitrite (NaNO2 inhibitor on the corrosion inhibition of mild steel in chloride bicarbonate solution has been studied using electrochemical techniques. Potentiodynamic polarisation data suggest that, when used in combination, KI and NaNO2 function together to inhibit reactions at both the anode and the cathode, but predominantly anodic. KI/NO2− concentration ratios varied from 2:1 to 2:5; inhibition efficiency was optimized for a ratio of 1:1. The surface morphology and corrosion products were analysed using scanning electron microscopy (SEM and X-ray diffractometry (XRD. The latter shows that the addition of I− to NO2 facilitates the formation of a passivating oxide (γ-Fe2O3 as compared to NO2− alone, decreasing the rate of metal dissolution observed in electrochemical testing. The synergistic effect of KI/NO2− inhibition was enhanced under the dynamic conditions associated with testing in a rotating disc electrode.

Internal structure, hydroscopic and reactive properties of mixed sodium methanesulfonate-sodium chloride particles

Czech Academy of Sciences Publication Activity Database

Liu, Y.; Minofar, Babak; Desyaterik, Y.; Dames, E.; Zhu, Z.; Cain, J. P.; Hopkins, R. J.; Gilles, M. K.; Wang, H.; Jungwirth, Pavel; Laskin, A.

2011-01-01

Roč. 13, č. 25 (2011), s. 11846-11857 ISSN 1463-9076 R&D Projects: GA MŠk LC512; GA MŠk(CZ) LC06010 Grant - others:GA MŠk(CZ) ME09062 Institutional research plan: CEZ:AV0Z40550506; CEZ:AV0Z60870520 Keywords : sodium methanesulfonate particles * air/water interface * molecular dynamics Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.573, year: 2011

Effects of de-icing chemicals sodium chloride and potassium formate on cadmium solubility in a coarse mineral soil

Energy Technology Data Exchange (ETDEWEB)

Rasa, Kimmo [Department of Applied Chemistry and Microbiology, University of Helsinki, P.O. Box 27, FIN-00014, University of Helsinki (Finland)]. E-mail: kimmo.rasa@helsinki.fi; Peltovuori, Tommi [Department of Applied Chemistry and Microbiology, University of Helsinki, P.O. Box 27, FIN-00014, University of Helsinki (Finland); Hartikainen, Helinae [Department of Applied Chemistry and Microbiology, University of Helsinki, P.O. Box 27, FIN-00014, University of Helsinki (Finland)

2006-08-01

Excessive use of sodium chloride (NaCl) as de-icing chemical causes environmental problems, such as elevated chloride concentrations in groundwater. On vulnerable sites, this can be avoided by using alternative organic de-icing chemicals, such as potassium formate (KHCOO). The environmental impacts of KCHOO are, however, not well known. This study reports the potential effects of NaCl and KCHOO on mechanisms controlling the mobility of cadmium (Cd) in roadside soils as a result of vehicular traffic. Changes in the solubility of Cd in a coarse mineral soil treated with these two de-icing chemicals were studied in a 50-day incubation experiment under four different moisture and temperature combinations and an initial soil Cd concentration of 3 mg kg{sup -1}. After incubation, the distribution of soil Cd into different fractions was analyzed using a sequential extraction method. Soil pH and soil redox potential were recorded and the occurrence of Cd-Cl complexes in the soil was estimated using published stability constants. During incubation, KCHOO lowered the soil redox potential, but this was not accompanied by a decrease in the sorption capacity of oxides and the release of oxide-bound Cd into soil solution. On the other hand, elevated pH (from 4.3 to 6.7-8.5) in the formate treatments increased the sorption of Cd onto the oxide surfaces (up to 80% of total sorbed Cd). In the NaCl treatments, cation competition and formation of Cd-Cl complexes increased the water-soluble Cd fraction. Consequently, the amount of bioavailable Cd was 3.5 times smaller in the KCHOO than in the NaCl treatments.

The role of sodium in the body

Directory of Open Access Journals (Sweden)

Munteanu Constantin

2011-05-01

Full Text Available Sodium is a metallic element with the symbol Na , in the same group with Li, K, Rb, Cs; is widespread in nature in the form of salts (nitrates, carbonates, chlorides, atomic number 11 and atomic weight 22,9898 . It,s a soft metal, reactive and with a low melting point , with a relative density of 0,97 at 200C (680 F. From the commercial point of view, sodium is the most important of all the alkaline metals. Elemental sodium was first isolated by Humpry Davy in 1807 by passing an electric current through molten sodium hydroxide. Elemental sodium does not occur naturally on earth, because it quickly oxidizes in air and is violently reactive with water, so it must be stored in a non-oxidizing medium, such as liquid hydrocarbon . The free metal is used for some chemical synthesis, analysis, and heat transfer applications .

The effect of steam curing on chloride penetration in geopolymer concrete

Directory of Open Access Journals (Sweden)

Jaya Ekaputri Januarti

2017-01-01

Full Text Available In this paper, we present the result of our study on the effect of steam curing to chloride ion penetration in geopolymer concrete. Class F fly ash was activated using sodium hydroxide (NaOH and sodium silicate (Na2SiO3. The concrete specimens were then steam-cured at 40°C, 60°C, 80°C and room temperature at 24 hours. The treatment was followed by wet curing for 28 days, and then followed by immersion of all specimens in salt water for the durations of 30, 60, and 90 days. Cylindrical specimens were then prepared for compressive strength, chloride ion penetration, pH, and porosity tests. A 16 mm-steel bar was fixed at the center of the specimen concrete blocks (specimen size: 10cm × 10cm × 15cm. Corrosion probability was determined by conducting Half Cell Potential test. Our result showed that increasing the curing temperature to 80°C induced chloride ion penetration into the concrete’s effective pores, despite improvements in compressive strength. We also found that chloride ingress on the geopolymer concrete increases commensurately with the increase of the curing temperature. The corrosion potential measurement of geopolymer concrete was higher than OPC concrete even if corrosion was not observed in reinforcing. Based on our result, we suggest that the corrosion categorization for geopolymer concretes needs to be adjusted.

Properties of Calcium Acetate Manufactured with Etching Waste Solution and Limestone Sludge as a Cementitious High-Early-Strength Admixture

OpenAIRE

Kim, Deuck-Mo; Ryu, Hwa-Sung; Shin, Sang-Heon; Park, Won-Jun

2016-01-01

Concrete is one of the most widely used construction materials. There are several methods available to improve its performance, with one of them being the use of high-early-strength admixtures (HESAs). Typical HESAs include calcium nitrate, calcium chloride, and calcium formate (CF). Industrial by-products, such as acetic acid and lime stone sludge (LSS), can be used together to produce calcium acetate (CA), which can subsequently be used as a cementitious HESA. In this study, calcium carbona...

Functional modifications of acid-sensing ion channels by ligand-gated chloride channels.

Directory of Open Access Journals (Sweden)

Xuanmao Chen

Full Text Available Together, acid-sensing ion channels (ASICs and epithelial sodium channels (ENaC constitute the majority of voltage-independent sodium channels in mammals. ENaC is regulated by a chloride channel, the cystic fibrosis transmembrane conductance regulator (CFTR. Here we show that ASICs were reversibly inhibited by activation of GABA(A receptors in murine hippocampal neurons. This inhibition of ASICs required opening of the chloride channels but occurred with both outward and inward GABA(A receptor-mediated currents. Moreover, activation of the GABA(A receptors modified the pharmacological features and kinetic properties of the ASIC currents, including the time course of activation, desensitization and deactivation. Modification of ASICs by open GABA(A receptors was also observed in both nucleated patches and outside-out patches excised from hippocampal neurons. Interestingly, ASICs and GABA(A receptors interacted to regulate synaptic plasticity in CA1 hippocampal slices. The activation of glycine receptors, which are similar to GABA(A receptors, also modified ASICs in spinal neurons. We conclude that GABA(A receptors and glycine receptors modify ASICs in neurons through mechanisms that require the opening of chloride channels.

Probing ion-specific effects on aqueous acetate solutions: Ion pairing versus water structure modifications.

Science.gov (United States)

Petit, Tristan; Lange, Kathrin M; Conrad, Gerrit; Yamamoto, Kenji; Schwanke, Christoph; Hodeck, Kai F; Dantz, Marcus; Brandenburg, Tim; Suljoti, Edlira; Aziz, Emad F

2014-05-01

The effect of monovalent cations (Li(+), K(+), NH4 (+), Na(+)) on the water structure in aqueous chloride and acetate solutions was characterized by oxygen K-edge X-ray absorption spectroscopy (XAS), X-ray emission spectroscopy, and resonant inelastic X-ray scattering (RIXS) of a liquid microjet. We show ion- and counterion dependent effects on the emission spectra of the oxygen K-edge, which we attribute to modifications of the hydrogen bond network of water. For acetates, ion pairing with carboxylates was also probed selectively by XAS and RIXS. We correlate our experimental results to speciation data and to the salting-out properties of the cations.

Probing ion-specific effects on aqueous acetate solutions: Ion pairing versus water structure modifications

Directory of Open Access Journals (Sweden)

Tristan Petit

2014-05-01

Full Text Available The effect of monovalent cations (Li+, K+, NH4+, Na+ on the water structure in aqueous chloride and acetate solutions was characterized by oxygen K-edge X-ray absorption spectroscopy (XAS, X-ray emission spectroscopy, and resonant inelastic X-ray scattering (RIXS of a liquid microjet. We show ion- and counterion dependent effects on the emission spectra of the oxygen K-edge, which we attribute to modifications of the hydrogen bond network of water. For acetates, ion pairing with carboxylates was also probed selectively by XAS and RIXS. We correlate our experimental results to speciation data and to the salting-out properties of the cations.

[Influence of non-sodium restricted diet with diuretics on plasma rennin, renal blood flow and in patients with cirrhotic ascites].

Science.gov (United States)

Zhu, Yin-fang; Gu, Xi-bing; Zhu, Hong-ying; Yang, Xiao-juan; Wang, Dong; Yu, Ping

2013-02-01

To explore influence of sodium restricted diet and non-sodium restricted diet on plasma rennin (PRA), angiotensin II (All), ALD, renal blood flow (RBF) and subside of ascites in patients with cirrhotic ascites. Eighty cases of hepatitis B with cirrhotic ascites were randomly divided into sodium restricted diet group and non-sodium restricted diet group. 39 cases were in non-sodium restricted diet group, taking sodium chloride 6500-8000 mg daily; 41 cases were in sodium restricted diet group, taking sodium chloride 5000 mg daily. Both groups received diuretics furosemide and spironolactone. Blood sodium, urine sodium, PRA, AII, ALD, RBF ascites subsiding were compared after treatment. In non-sodium restricted diet group, blood sodium and urine sodium increased 10 days after treatment compared with those before treatment, and compared with those of sodium restricted diet group 10 days after treatment, P Renal damage induced by low blood sodium after treatment was less in non-sodium restricted diet group than that in sodium restricted diet group, P blood sodium, thus increasing excretion of urine sodium and diuretic effect. It can also decrease levels of PRA, AII and ALD, increase renal blood flow and prevent renal damage induced by low blood sodium and facilitate subsiding of ascites.

Localized corrosion of molybdenum-bearing nickel alloys in chloride solutions

International Nuclear Information System (INIS)

Postlethwaite, J.; Scoular, R.J.; Dobbin, M.H.

1988-01-01

Electrochemical and immersion tests have been applied to a study of the localized corrosion resistance of two molybdenum-bearing nickel alloys. Alloys C-276 and 6y25, in neutral chloride solutions in the temperature range of 25 to 200 C as part of the container materials evaluation screening tests for the Canadian Nuclear Fuel Waste Management Program. Cyclic polarization studies show that the passivation breakdown potentials move rapidly to more active values with increasing temperatures, indicating a reduced resistance to localized corrosion. The results of immersion tests show that both alloys do suffer crevice corrosion in neutral aerated sodium chloride solutions at elevated temperatures, but that in both cases there is a limiting temperature > 100C, below which, the alloys are not attacked, regardless of the chloride concentration

Comparison of a sodium-based and a chloride-based approach for the determination of sodium chloride content of processed foods in the Netherlands

NARCIS (Netherlands)

Capuano, E.; Veer, van der G.; Verheijen, P.J.J.; Heenan, S.P.; Laak, van de L.F.J.; Koopmans, H.B.M.; Ruth, van S.M.

2013-01-01

This study reports and discusses the sodium content of a set of 1016 processed food samples collected in the Netherlands, which covered 10 food groups (cakes/pastries, chips/nuts, sauces, processed meat, conserves, snacks, ready-to-eat products, cheese, bread, and soups) and 100 food commodities.

Use of Consumer Acceptability as a Tool to Determine the Level of Sodium Reduction: A Case Study on Beef Soup Substituted With Potassium Chloride and Soy-Sauce Odor.

Science.gov (United States)

Lee, Cho Long; Lee, Soh Min; Kim, Kwang-Ok

2015-11-01

potassium chloride and salty-congruent odor. The result showed that considering consumer acceptability during sodium reduction enabled to better understand the potentials of the sodium substitutes and salty-congruent odor. © 2015 Institute of Food Technologists®

Comparison of the effect of acetic, propionic and butyric acids on ...

African Journals Online (AJOL)

番茄花园

2011-05-23

May 23, 2011 ... Graded levels of mixed VFA sodium salt (the molar proportion of acetate, propionate, and butyrate was 65:25:10), i.e. 0, 5, ... be more associated with the VFA energy level (Ma and. Zhao, 2010) and mediated by IGF-I, insulin ..... Influence of nutrition and bovine growth hormone (GH) on hepatic GH binding, ...

Effect of malva nut gum (purified and crude), sodium chloride and phosphate on cooking, texture, colour, rheology and microstructure of different chicken meat batters.

Science.gov (United States)

Barbut, S; Somboonpanyakul, P; Quinton, M; Smith, A

2009-01-01

1. In the first experiment, the effect of adding purified malva nut gum (PMG) to comminuted poultry breast meat batters formulated with different contents of sodium chloride (NaCl; 10 to 30 g/kg) and tripolyphosphate (TPP; 0 and 5 g/kg) was studied. 2. Increasing salt (sodium chloride) content, along with the addition of 1 g/kg PMG, was beneficial in reducing cooking loss. At all salt contents, batters with PMG showed lower springiness than batters without PMG. Adding PMG to the batter with 20 g/kg salt and TPP decreased fracture force, springiness and chewiness. 3. In a second experiment, the effects of PMG (0.0, 3.0 and 6.0 g/kg), crude malva nut gum (CMG; 3.0 g/kg) and TPP (0.0 and 4.0 g/kg) on cooking loss, fat loss, colour, texture, rheology and microstructure of emulsified chicken meat batters were studied. 4. Increasing PMG reduced cooking and fat losses. Adding TPP increased hardness, springiness, cohesiveness and chewiness. The 1.0 g/kg PMG and TPP provided the greatest hardness. The batter with 3.0 g/kg PMG resulted in the lowest lightness (L*) and highest redness (a*). Adding PMG and TPP resulted in stable batters, as was evident by light microscopy results. The rheological evaluation showed the highest G' in the batter with 4.0 g/kg TPP followed in decreasing order by the batters containing TPP plus 3.0 g/kg PMG, TPP plus 1.0 g/kg PMG, 3.0 g/kg PMG, 1.0 g/kg PMG, 3.0 g/kg CMG and the control. 5. Overall, the results are important for developing new applications where malva nut gum can be used to improve yield and stability of meat products.

[Determination of Chloride Salt Solution by NIR Spectroscopy].

Science.gov (United States)

Zhang, Bin; Chen, Jian-hong; Jiao, Ming-xing

2015-07-01

Determination of chloride salt solution by near infrared spectrum plays a very important role in Biomedicine. The near infrared spectrum analysis of Sodium chloride, potassium chloride, calcium chloride aqueous solution shows that the concentration change of chloride salt can affect hydrogen bond, resulting in the variation of near infrared spectrum of water. The temperature influence on NIR spectrum has been decreased by choosing reasonable wavelength range and the wavelength where the temperature effects are zero (isosbestic point). Chlorine salt prediction model was established based on partial least squares method and used for predicting the concentration of the chlorine ion. The impact on near infrared spectrum of the cation ionic radius, the number of ionic charge, the complex effect of ionic in water has also discussed in this article and the reason of every factor are analysed. Experimental results show that the temperature and concentration will affect the near-infrared spectrum of the solution, It is found that the effect of temperature plays the dominant role at low concentrations of chlorine salt; rather, the ionic dominates at high concentration. Chloride complexes are formed in aqueous solution, It has an effect on hydrogen bond of water combining with the cations in chlorine salt solution, Comparing different chloride solutions at the same concentration, the destruction effects of chloride complexes and catnions on the hydrogen bond of water increases in the sequences: CaCl2 >NaCl>KC. The modeling result shows that the determination coefficients (R2) = 99.97%, the root mean square error of cross validation (RM- SECV) = 4.51, and the residual prediction deviation (RPD) = 62.7, it meets the daily requirements of biochemical detection accuracy.

Processed foods aimed at children and adolescents: sodium content, adequacy according to the dietary reference intakes and label compliance

Directory of Open Access Journals (Sweden)

Vera Favila Ribeiro

2013-08-01

Full Text Available OBJECTIVE: This study determined the sodium content of processed foods aimed at children and adolescents and the adequacy of its content in relation to the dietary reference intakes, and verified label compliance. METHODS: The sodium content of 17 food samples (instant noodles, breaded items, hamburger patties, hot dogs and bologna sausages was determined by flame photometry and chloride titration, and the results were compared with nutritional data. The labels were checked for compliance with the pertinent laws. RESULTS: According to flame photometry and chloride titration, 13 and 5 products, respectively, had sodium contents that exceeded those reported on the nutrition facts label by more than 20%. All samples had more than 480mg of sodium per serving. The tolerable upper intake level for sodium for children aged 4-8 years was exceeded in 8 instant noodles and 3 breaded items according to flame photometry, and in 9 items according to chloride titration. Regarding the legislation, 5 products used a daily reference intake other than that provided by the legislation to report their percent sodium content per serving. Moreover, the serving sizes of 3 instant noodles, the terminology used in 1 instant noodles and the protein content of 1 breaded item were also not compliant with the legislation. CONCLUSION: The sodium contents in the study samples were high and there was no regard for the legislation.

Final report on the safety assessment of ethoxyethanol and ethoxyethanol acetate.

Science.gov (United States)

Johnson, Wilbur

2002-01-01

Ethoxyethanol is an ether alcohol described as a solvent and viscosity-decreasing agent for use in cosmetics. Ethoxyethanol Acetate is the ester of Ethoxyethanol and acetic acid described as a solvent for use in cosmetics. Although these ingredients have been used in the past, neither ingredient is in current use. Ethoxyethanol is produced by reacting ethylene oxide with ethyl alcohol. Ethoxyethanol Acetate is produced via an esterification of Ethoxyethanol and acetic acid, acetic acid anhydride, or acetic chloride. Ethoxyethanol is metabolized to ethoxyacetaldehyde, which is further metabolized to ethoxyacetic acid, which is also a metabolite of Ethoxyethanol Acetate. Low to moderate acute inhalation toxicity is seen in animals studies. Acute oral toxicity studies in several species reported kidney damage, including extreme tubular degeneration. Kidney damage was also seen in acute dermal toxicity studies in rats and rabbits. Minor liver and kidney damage was also seen in short-term studies of rats injected subcutaneously with Ethoxyethanol, but was absent in dogs dosed intravenously. Mixed toxicity results were also seen in subchronic tests in mice and rats. Ethoxyethanol and Ethoxyethanol Acetate were mild to moderate eye irritants in rabbits; mild skin irritants in rabbits, and nonsensitizing in guinea pigs. Most genotoxicity tests were negative, but chromosome aberrations and sister-chromatid exchanges were among the positive results seen. Numerous reproductive and developmental toxicity studies, across several species, involving various routes of administration, indicate that Ethoxyethanol and Ethoxyethanol Acetate are reproductive toxicants and teratogens. Mild anemia was reported in individuals exposed occupationally to Ethoxyethanol, which resolved when the chemical was not used. Reproductive effects have been noted in males exposed occupationally to Ethoxyethanol. Although there are insufficient data to determine the potential carcinogenic effects of

Pitting Corrosion of Ni3(Si,Ti Intermetallic Compound at Various Chloride Concentrations

Directory of Open Access Journals (Sweden)

Gadang Priyotomo

2013-10-01

Full Text Available The pitting corrosion of Ni3(Si,Ti intermetallic compound was investigated as function of chloride concentration by using electrochemical method and scanning electron microscope in sodium chloride solutions at 293 K.  In addition, the pitting corrosion of type C276 alloy was also studied under the same experimental condition for comparison.  The pitting potential obtained for the intermetallic compound decreased with increasing chloride concentration.  The specific pitting potential and pitting potential of Ni3(Si,Ti were lower than those of C276 alloy, which means that the pitting corrosion resistance of C276 alloy was higher than that of Ni3(Si,Ti.

Chloride and sodium uptake potential over an entire rotation of Populus irrigated with landfill leachate.

Science.gov (United States)

Zalesny, Jill A; Zalesny, Ronald S

2009-07-01

There is a need for information about the response of Populus genotypes to repeated application of high-salinity water and nutrient sources throughout an entire rotation. We have combined establishment biomass and uptake data with mid- and full-rotation growth data to project potential chloride (Cl-) and sodium (Na+) uptake for 2- to 11-year-old Populus in the north central United States. Our objectives were to identify potential levels of uptake as the trees developed and stages of plantation development that are conducive to variable application rates of high-salinity irrigation. The projected cumulative uptake of Cl- and Na+ during mid-rotation plantation development was stable 2 to 3 years after planting but increased steadily from year 3 to 6. Year six cumulative uptake ranged from 22 to 175 kg Cl- ha(-1) and 8 to 74 kg Na+ ha(-1), while annual uptake ranged from 8 to 54 kg Cl- ha(-1) yr(-1) and 3 to 23 kg Na+ ha(-1) yr(-1). Full-rotation uptake was greatest from 4 to 9 years (Cl-) and 4 to 8 years (Na+), with maximum levels of Cl- (32 kg ha(-1) yr(-1)) and Na+ (13 kg ha(-1) yr(-1)) occurring in year six. The relative uptake potential of Cl- and Na+ at peak accumulation (year six) was 2.7 times greater than at the end of the rotation.

Physical and Chemical Stability of Urapidil in 0.9% Sodium Chloride in Elastomeric Infusion Pump.

Science.gov (United States)

Tomasello, Cristina; Leggieri, Anna; Rabbia, Franco; Veglio, Franco; Baietto, Lorena; Fulcheri, Chiara; De Nicolò, Amedeo; De Perri, Giovanni; D'Avolio, Antonio

2016-01-01

Urapidil is an antihypertensive agent, usually administered through intravenous bolus injection, slow-intravenous infusion, or continuous-drug infusion by perfusor. Since to date no evidences are available on drug stability in elastomeric pumps, patients have to be hospitalized. The purpose of this study was to validate an ultra-performance liquid chromatographic method to evaluate urapidil stability in an elastomeric infusion pump, in order to allow continuous infusion as home-care treatment. Analyses were conducted by diluting urapidil in an elastomeric pump. Two concentrations were evaluated: 1.6 mg/mL and 3.3 mg/mL. For the analyses, a reverse-phase ultra-performance liquid chromatographic- photodiode array detection instrument was used. Stressed degradation, pH changes, and visual clarity were used as stability indicators up to 10 days after urapidil solution preparation. The drug showed no more than 5% degradation during the test period at room temperature. No pH changes and no evidences of incompatibility were observed. Stress tests resulted in appreciable observation of degradation products. Considering the observed mean values, urapidil hydrochloride in sodium chloride 0.9% in elastomeric infusion pumps is stable for at least 10 days. These results indicate that this treatment could be administered at home for a prolonged duration (at least 7 days) with a satisfactory response. Copyright© by International Journal of Pharmaceutical Compounding, Inc.

Levels of ammonium, sulfate, chloride, calcium, and sodium in snow and ice from southern Greenland

International Nuclear Information System (INIS)

Busenberg, E.; Langway, C.C. Jr.

1979-01-01

Chemical analysis of surface snows and dated ice core samples from Dye 3, Greenland, suggests that the ammonium cation is a major constituent in all samples and that the annual ammonium levels present in the south Greenland samples have varied from 3.3 to 26.3 μg/kg between the seventeenth century and the present time. The annual range of 1974--1975 surface samples was between 3.8 and 8.8 μg/kg, while the mean was 5.7 +- 1.8 μ/kg. The recent large-scale uses of fixed nitrogen fertilizers and industrial pollution have apparently not affected the levels of ammonia reaching southern Greenland. The sodium and chloride present are predominantly derived from ocean spray, while more than 90% of the calcium is of continental origin. The levels of these three elements have not apparently been affected by human activity since the industrial revolution. Sulfate levels have increased dramatically since the industrial revolution, suggesting that sulfate of anthropogenic origin is the most important source of sulfate in modern snows from southern Greenland. The amount of the sulfuric acid neutralized by the ammonium cations was approximately 100% in the seventeenth and eighteenth centuries, dropping to approximately 20% in the 1974--1975 samples. These figures imply that there has been in increase in the acidity of precipitation in southern Greenland since the end of the eighteenth ce

Synthesis and crystal structure analysis of uranyl triple acetates

Energy Technology Data Exchange (ETDEWEB)

Klepov, Vladislav V., E-mail: vladislavklepov@gmail.com [Institute for Energy and Climate Research (IEK-6), Forschungszentrum Jülich GmbH, 52428 Jülich (Germany); Department of Chemistry, Samara National Research University, 443086 Samara (Russian Federation); Serezhkina, Larisa B.; Serezhkin, Victor N. [Department of Chemistry, Samara National Research University, 443086 Samara (Russian Federation); Alekseev, Evgeny V., E-mail: e.alekseev@fz-juelich.de [Institute for Energy and Climate Research (IEK-6), Forschungszentrum Jülich GmbH, 52428 Jülich (Germany); Institut für Kristallographie, RWTH Aachen University, 52066 Aachen (Germany)

2016-12-15

Single crystals of triple acetates NaR[UO{sub 2}(CH{sub 3}COO){sub 3}]{sub 3}·6H{sub 2}O (R=Mg, Co, Ni, Zn), well-known for their use as reagents for sodium determination, were grown from aqueous solutions and their structural and spectroscopic properties were studied. Crystal structures of the mentioned phases are based upon (Na[UO{sub 2}(CH{sub 3}COO){sub 3}]{sub 3}){sup 2–} clusters and [R(H{sub 2}O){sub 6}]{sup 2+} aqua-complexes. The cooling of a single crystal of NaMg[UO{sub 2}(CH{sub 3}COO){sub 3}]{sub 3}·6H{sub 2}O from 300 to 100 K leads to a phase transition from trigonal to monoclinic crystal system. Intermolecular interactions between the structural units and their mutual packing were studied and compared from the point of view of the stereoatomic model of crystal structures based on Voronoi-Dirichlet tessellation. Using this method we compared the crystal structures of the triple acetates with Na[UO{sub 2}(CH{sub 3}COO){sub 3}] and [R(H{sub 2}O){sub 6}][UO{sub 2}(CH{sub 3}COO){sub 3}]{sub 2} and proposed reasons of triple acetates stability. Infrared and Raman spectra were collected and their bands were assigned. - Graphical abstract: Single crystals of uranium based triple acetates, analytical reagents for sodium determination, were synthesized and structurally, spectroscopically and topologically characterized. The structures were compared with the structures of compounds from preceding families [M(H{sub 2}O){sub 6})][UO{sub 2}(CH{sub 3}COO){sub 3}]{sub 2} (M = Mg, Co, Ni, Zn) and Na[UO{sub 2}(CH{sub 3}COO){sub 3}]. Analysis was performed with the method of molecular Voronoi-Dirichlet polyhedra to reveal a large contribution of the hydrogen bonds into intermolecular interactions which can be a reason of low solubility of studied complexes.

Inactivation of foot-and-mouth disease virus by citric acid and sodium carbonate with deicers.

Science.gov (United States)

Hong, Jang-Kwan; Lee, Kwang-Nyeong; You, Su-Hwa; Kim, Su-Mi; Tark, Dongseob; Lee, Hyang-Sim; Ko, Young-Joon; Seo, Min-Goo; Park, Jong-Hyeon; Kim, Byounghan

2015-11-01

Three out of five outbreaks of foot-and-mouth disease (FMD) since 2010 in the Republic of Korea have occurred in the winter. At the freezing temperatures, it was impossible to spray disinfectant on the surfaces of vehicles, roads, and farm premises because the disinfectant would be frozen shortly after discharge and the surfaces of the roads or machines would become slippery in cold weather. In this study, we added chemical deicers (ethylene glycol, propylene glycol, sodium chloride, calcium chloride, ethyl alcohol, and commercial windshield washer fluid) to keep disinfectants (0.2% citric acid and 4% sodium carbonate) from freezing, and we tested their virucidal efficacies under simulated cold temperatures in a tube. The 0.2% citric acid could reduce the virus titer 4 logs at -20°C with all the deicers. On the other hand, 4% sodium carbonate showed little virucidal activity at -20°C within 30 min, although it resisted being frozen with the function of the deicers. In conclusion, for the winter season, we may recommend the use of citric acid (>0.2%) diluted in 30% ethyl alcohol or 25% sodium chloride solvent, depending on its purpose. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Selective sodium removal from lithium chloride brine with novel ...

African Journals Online (AJOL)

Natrium superionic conductor (NASICON) ceramics present interesting sensitive and selective properties against alkaline cations due to their structure. The powder of Li1.4La0.4Zr1.6(PO4)3 has been synthesized by a solid phase reaction. The removal of sodium was studied in an extensive series of tests involving different ...

Simultaneous HPLC method for determination of sodium trimethoprim phenylpropanol disulphonate and sodium sulfaquinoxaline in veterinary drugs

Directory of Open Access Journals (Sweden)

Puangkaew Lakkanatinaporn

2004-11-01

Full Text Available A simple HPLC method has been developed for the separation and determination of sodium trimethoprim phenylpropanol disulphonate and sodium sulfaquinoxaline in veterinary preparations. Both drugs were separated well on a Kromasil C18 column (5 µm, 150 × 4.6 mm using a mixture of acetonitrile and 0.5% triethylamine in 1% acetic acid, pH 3 (18:82, v/v as the mobile phase at the flow rate of 1.5 ml/ min. The presence of both substances was monitored by UV absorption detection at 271 nm. The retention times of sodium trimethoprim phenylpropanol disulphonate and sodium sulfaquinoxaline were 3.2 and 16.0 min, respectively. The performance of the developed method was tested. Linear responses of both drugs were achieved between 48-145% of labeled amount over the concentration ranges of 35-101 µg/ml and 102-306 µg/ ml for sodium trimethoprim phenylpropanol disulphonate and sodium sulfaquinoxaline with correlation coefficients (R2 of 0.9980 and 0.9998, respectively. Accuracy expressed in term of recoveries were 101.4± 1.21% (n=6 for sodium trimethoprim phenylpropanol disulphonate and 99.7±0.92% (n=6 for sodium sulfaquinoxaline. Precision of the method in terms of the relative standard deviation is not more than 2% in all cases. These figures of merit indicated the validity of the developed method.

Formation of glutathione conjugates by reactive metabolites of vinylidene chloride in microsomes and isolated hepatocytes

International Nuclear Information System (INIS)

Liebler, D.C.; Meredith, M.J.; Guengerich, F.P.

1985-01-01

Oxidation of the vinyl halide carcinogen and hepatotoxin vinylidene chloride (VDC) by microsomal cytochrome P-450 yields 2,2-dichloroacetaldehyde, 2-chloroacetyl chloride, 2-chloroacetic acid, and 1,1-dichloroethylene oxide. The roles of these metabolites in covalent modification of proteins and reduced glutathione (GSH) were examined. 2-Chloroacetyl chloride reacted with model thiols at least 10(3)-fold faster than did 1,1-dichloroethylene oxide and at least 10(5)-fold faster than did 2,2-dichloroacetaldehyde or 2-chloroacetic acid. Microsomal covalent binding of [ 14 C]VDC was inhibited by GSH but not by lysine, suggesting that protein thiols, rather than amino groups, are major targets. Liver microsomes catalyzed the formation of three GSH:VDC metabolite conjugates, identified as S-(2,2-dichloro-1-hydroxy)ethylglutathione, 2-(S-glutathionyl)acetate, and S-(2-glutathionyl)acetylglutathione, a novel conjugate containing both stable (thioether) and labile (thioester) linkages. The latter two conjugates also were formed in isolated rat hepatocytes and measurable amounts of 2-(S-glutathionyl)acetate were released into the incubation medium. Both 2-(S-glutathionyl)acetate and S-(2-glutathionyl)acetylglutathione were formed with [ 35 S]GSH added to the hepatic medium, indicating that reactive VDC metabolites are capable of crossing the plasma membrane to react with extracellular targets. Unlabeled S-(2-glutathionyl)-acetylglutathione underwent carbonyl substitution with added [ 35 S]GSH, suggesting that this conjugate may participate in modification of protein thiols. This conjugate also underwent hydrolysis with a half-life of approximately 3 hr. GSH:VDC metabolite conjugates may serve as accessible models for labile covalent adducts formed between VDC metabolites and protein thiols

Salt craving: the psychobiology of pathogenic sodium intake.

Science.gov (United States)

Morris, Michael J; Na, Elisa S; Johnson, Alan Kim

2008-08-06

Ionic sodium, obtained from dietary sources usually in the form of sodium chloride (NaCl, common table salt) is essential to physiological function, and in humans salt is generally regarded as highly palatable. This marriage of pleasant taste and physiological utility might appear fortunate--an appealing taste helps to ensure that such a vital substance is ingested. However, the powerful mechanisms governing sodium retention and sodium balance are unfortunately best adapted for an environment in which few humans still exist. Our physiological and behavioral means for maintaining body sodium and fluid homeostasis evolved in hot climates where sources of dietary sodium were scarce. For many reasons, contemporary diets are high in salt and daily sodium intakes are excessive. High sodium consumption can have pathological consequences. Although there are a number of obstacles to limiting salt ingestion, high sodium intake, like smoking, is a modifiable behavioral risk factor for many cardiovascular diseases. This review discusses the psychobiological mechanisms that promote and maintain excessive dietary sodium intake. Of particular importance are experience-dependent processes including the sensitization of the neural systems underlying sodium appetite and the effects of sodium balance on hedonic state and mood. Accumulating evidence suggests that plasticity within the central nervous system as a result of experience with high salt intake, sodium depletion, or a chronic unresolved sodium appetite fosters enduring changes in sodium related appetitive and consummatory behaviors.

Vapour pressures, densities, and viscosities of the (water + lithium bromide + potassium acetate) system and (water + lithium bromide + sodium lactate) system

International Nuclear Information System (INIS)

Lucas, Antonio de; Donate, Marina; Rodriguez, Juan F.

2006-01-01

Measurements of thermophysical properties (vapour pressure, density, and viscosity) of the (water + lithium bromide + potassium acetate) system LiBr:CH 3 COOK = 2:1 by mass ratio and the (water + lithium bromide + sodium lactate) system LiBr:CH 3 CH(OH)COONa = 2:1 by mass ratio were measured. The system, a possible new working fluid for absorption heat pump, consists of absorbent (LiBr + CH 3 COOK) or (LiBr + CH 3 CH(OH)COONa) and refrigerant H 2 O. The vapour pressures were measured in the ranges of temperature and absorbent concentration from T = (293.15 to 333.15) K and from mass fraction 0.20 to 0.50, densities and viscosities were measured from T = (293.15 to 323.15) K and from mass fraction 0.20 to 0.40. The experimental data were correlated with an Antoine-type equation. Densities and viscosities were measured in the same range of temperature and absorbent concentration as that of the vapour pressure. Regression equations for densities and viscosities were obtained with a minimum mean square error criterion

Toxicity of sodium chloride and methyl parathion on the macrophyte Lemna minor (Linnaeus, 1753 with respect to frond number and chlorophyll

Directory of Open Access Journals (Sweden)

Erlei Cassiano Keppeler

2009-09-01

Full Text Available Duckweed, Lemna minor L., is a suitable plant model for toxicity evaluation of many contaminants due to its small size and rapid growth. Methyl parathion is a toxic compound which is utilized to eliminate aquatic insect larvae, among other purposes. Its toxicity was evaluated with the use of L. minor in this study. Methyl parathion was added to Hoagland’s nutrient medium at concentrations of 0, 8, 16, 22, 28 and 32mg.L–1. Lemna minor is used as a tool in evaluating chemical test products for toxic effects. The sensitivity of Lemna to sodium chloride, the reference substance, at concentrations of 0, 2, 4, 6, 7 and 8 g.L–1, was determined for comparison and resulted in an IC50 of 6.87g.L–1. Methyl parathion in L. minor showed an IC50 of 49.48mg.L–1.

Thermodynamics of aqueous carbonate solutions including mixtures of sodium carbonate, bicarbonate, and chloride

Energy Technology Data Exchange (ETDEWEB)

Peiper, J.C.; Pitzer, K.S.

1982-01-01

Recently the authors examined electrochemical-cell data leading to values of the activity coefficient for aqueous sodium bicarbonate. Since that preliminary analysis, new experimental measurements have been published which contribute significantly to the overall thermodynamic understanding of (sodium carbonate + sodium bicarbonate + carbonic acid). In this more extensive examination we consider a wide variety of measurements leading to activity coefficients of Na/sub 2/CO/sub 3/ and NaHCO/sub 3/ from 273 to 323 K and to relative molar enthalpies and heat capacities at 298.15 K. Tables of thermodynamic quantities at selected temperatures are included. 47 references, 2 figures, 6 tables.

The "chloride theory", a unifying hypothesis for renal handling and body fluid distribution in heart failure pathophysiology.

Science.gov (United States)

Kataoka, Hajime

2017-07-01

Body fluid volume regulation is a complex process involving the interaction of various afferent (sensory) and neurohumoral efferent (effector) mechanisms. Historically, most studies focused on the body fluid dynamics in heart failure (HF) status through control of the balance of sodium, potassium, and water in the body, and maintaining arterial circulatory integrity is central to a unifying hypothesis of body fluid regulation in HF pathophysiology. The pathophysiologic background of the biochemical determinants of vascular volume in HF status, however, has not been known. I recently demonstrated that changes in vascular and red blood cell volumes are independently associated with the serum chloride concentration, but not the serum sodium concentration, during worsening HF and its recovery. Based on these observations and the established central role of chloride in the renin-angiotensin-aldosterone system, I propose a unifying hypothesis of the "chloride theory" for HF pathophysiology, which states that changes in the serum chloride concentration are the primary determinant of changes in plasma volume and the renin-angiotensin-aldosterone system under worsening HF and therapeutic resolution of worsening HF. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sodium Alginate with PEG/PEO Blends as a Floating Drug Delivery Carrier – In vitro Evaluation

Directory of Open Access Journals (Sweden)

Christe Sonia Mary

2016-09-01

Full Text Available Purpose: Floating drug delivery system reduces the quantity of drug intake and the risk of overloading the organs with excess drug. Methods: In the present study, we prepared the blends of sodium alginate with polyethylene glycol (PEG and polyethylene oxide (PEO as a matrix, sodium hydrogen carbonate as a pore forming agent, methyl cellulose as a binder and barium chloride containing 10% acetic acid as a hardening agent. Different ratios of pore forming agent to the polymer blend was used to prepare the floating beads with different porosity and morphology. Ciprofloxacin hydrochloride was used as a model drug for the release kinetics studies. Results: The beads were characterized by optical and FESEM microscopy to study the morphology and pore dimensions. The results obtained shows decrease in beads size with increase in the concentration of the pore forming agent. The swelling properties of the beads were found to be in the range of 80% to 125%. The release kinetics of the ciprofloxacin from the beads was measured by UV-Visible spectroscopy at λmax of 278nm and the results shows for highly porous beads. Conclusion: By varying the amount of alginate and pore forming agent the release kinetics is found to get altered. As a result, ciprofloxacin hydrochloride release is found to be sustained from the blended beads.

Determination of microamounts of potassium in sodium iodide by atomic absorption spectrometry

International Nuclear Information System (INIS)

Ogasawara, Ken; Ohta, Masatoshi; Abe, Kenzo

1980-01-01

Microdetermination of potassium in sodium iodide was developed by the standard addition method. Twenty grams of sample were dissolved in 50 ml of water in a quartz beaker. To the solution, 30 ml of concentrated hydrochloric acid and 30 ml of 30% hydrogen peroxide were added, and evaporated to dryness. By this process sodium iodide was converted into sodium chloride. The cake thus obtained was dissolved in water and diluted to exactly 200 ml. To 25 ml aliquots of the solution, the standard potassium and cesium chloride solutions were added and diluted to 50 ml with water; the concentration of potassium was 0 -- 1 mg/l and that of cesium 4 mM. These solutions were introduced into an air-propane flame and the absorbances were measured at 769.9 nm. During the conversion reaction, hydrochloric acid was completely decomposed, and remained hydrogen peroxide had no influence for absorbance, and other backgrounds were negligible. The linear calibration curve was obtained in the range 0 -- 2 mg of potassium per liter. Potassium in sodium iodide was determined by this method within the coefficient of variation of +-(20 -- 3)% in the range (1.7 -- 32.5) ppm. (author)

Evaluation of chloride-ion-specific electrodes as in situ chemical sensors for monitoring total chloride concentration in aqueous solutions generated during the recovery of plutonium from molten salts used in plutonium electrorefining operations

International Nuclear Information System (INIS)

Smith, W.H.

1992-10-01

Two commercially available chloride-ion-specific electrodes (CLISEs), a solid-state type and a membrane type, were evaluated as potential in situ chemical sensors for determining total chloride ion concentration in mixed sodium chloride/potassium chloride/hydrochloric acid solutions generated during the recovery of plutonium from molten salts used in plutonium electrorefining operations. Because the response of the solid-state CLISE was closer than was the response of the membrane-type CLISE to the theoretical response predicted by the Nernst equation, the solid-state CLISE was selected for further evaluation. A detailed investigation of the characteristics of the chloride system and the corresponding CLISE response to concentration changes suggested four methods by which the CLISE could be used either as a direct, in situ sensor or as an indirect sensor through which an analysis could be performed on-line with a sample extracted from the process solution

Studies on lipids and fatty acids in rats with streptozotocin-induced insulin deficiency II. Incorporation of 1-(14)C-sodium acetate into lipids and fatty acids of liver slices and whole blood cells

OpenAIRE

三宅,寛治

1988-01-01

In order to study the lipid and fatty acid metabolism in the insulin deficient state, the in vitro incorporation of 1-(14)C-sodium acetate into major lipid fractions and fatty acids of liver slices and whole blood cells was determined. Rats were studied one week, one month and three months after insulin deficiency was induced by administration of streptozotocin.The net incorporation of (14)C into lipid fractions and total fatty acids of liver slices significantly decreased after one week. On ...

An improved synthesis of 1,3,5-triaryl-2-pyrazolines in acetic acid aqueous solution under ultrasound irradiation

Directory of Open Access Journals (Sweden)

Lin Zhi-Ping

2007-03-01

Full Text Available Abstract Background Pyrazoline derivatives have been found to possess a broad spectrum of biological activities. Among various pyrazoline derivatives, 2-pyrazolines seem to be the most frequently studied. A variety of methods have been reported for the preparation of this class of compound. However, in spite of their potential utility, some of the reported methods suffer from drawbacks such as long reaction times, cumbersome product isolation procedures and environmental concerns. Organic reactions in aqueous media have attracted increasing interest recently because of environmental issues and the understanding of biochemical processes. Ultrasound has increasingly been used in organic synthesis in the last three decades. A large number of organic reactions can be carried out in higher yields, shorter reaction time or milder conditions under ultrasound irradiation. Results Preparation of a series of 1,3,5-triaryl-2-pyrazolines through the reaction of chalcones and phenylhydrazine hydrochloride was carried out in 83–96% yield within 1.5–2 h in sodium acetate-acetic acid aqueous solution under ultrasound irradiation. Conclusion We have described a practical and convenient procedure for the synthesis of 1,3,5-triaryl-2-pyrazolines in sodium acetate-acetic acid aqueous solution at room temperature under ultrasound irradiation.

Calcium phosphate stabilization of fly ash with chloride extraction.

Science.gov (United States)

Nzihou, Ange; Sharrock, Patrick

2002-01-01

Municipal solid waste incinerator by products include fly ash and air pollution control residues. In order to transform these incinerator wastes into reusable mineral species, soluble alkali chlorides must be separated and toxic trace elements must be stabilized in insoluble form. We show that alkali chlorides can be extracted efficiently in an aqueous extraction step combining a calcium phosphate gel precipitation. In such a process, sodium and potassium chlorides are obtained free from calcium salts, and the trace metal ions are immobilized in the calcium phosphate matrix. Moderate calcination of the chemically treated fly ash leads to the formation of cristalline hydroxylapatite. Fly ash spiked with copper ions and treated by this process shows improved stability of metal ions. Leaching tests with water or EDTA reveal a significant drop in metal ion dissolution. Hydroxylapatite may trap toxic metals and also prevent their evaporation during thermal treatments. Incinerator fly ash together with air pollution control residues, treated by the combined chloride extraction and hydroxylapatite formation process may be considered safe to use as a mineral filler in value added products such as road base or cement blocks.

Extended Stability of Epinephrine Hydrochloride Injection in Polyvinyl Chloride Bags Stored in Amber Ultraviolet Light-Blocking Bags.

Science.gov (United States)

Van Matre, Edward T; Ho, Kang C; Lyda, Clark; Fullmer, Beth A; Oldland, Alan R; Kiser, Tyree H

2017-09-01

Objective: The objective of this study was to evaluate the stability of epinephrine hydrochloride in 0.9% sodium chloride in polyvinyl chloride bags for up to 60 days. Methods: Dilutions of epinephrine hydrochloride to concentrations of 16 and 64 µg/mL were performed under aseptic conditions. The bags were then placed into ultraviolet light-blocking bags and stored at room temperature (23°C-25°C) or under refrigeration (3°C-5°C). Three samples of each preparation and storage environment were analyzed on days 0, 30, 45, and 60. Physical stability was performed by visual examination. The pH was assessed at baseline and upon final degradation evaluation. Sterility of the samples was not assessed. Chemical stability of epinephrine hydrochloride was evaluated using high-performance liquid chromatography. To determine the stability-indicating nature of the assay, degradation 12 months following preparation was evaluated. Samples were considered stable if there was less than 10% degradation of the initial concentration. Results: Epinephrine hydrochloride diluted to 16 and 64 µg/mL with 0.9% sodium chloride injection and stored in amber ultraviolet light-blocking bags was physically stable throughout the study. No precipitation was observed. At days 30 and 45, all bags had less than 10% degradation. At day 60, all refrigerated bags had less than 10% degradation. Overall, the mean concentration of all measurements demonstrated less than 10% degradation at 60 days at room temperature and under refrigeration. Conclusion: Epinephrine hydrochloride diluted to 16 and 64 µg/mL with 0.9% sodium chloride injection in polyvinyl chloride bags stored in amber ultraviolet light-blocking bags was stable up to 45 days at room temperature and up to 60 days under refrigeration.

Synthesis and characterization of foldable and magnetic field-sensitive, freestanding poly(vinyl acetate)/poly(vinyl chloride)/polyfuran composite and nanocomposite films

Energy Technology Data Exchange (ETDEWEB)

Sarıtaş, Sevilay; Eşsiz, Serpil; Sarı, Bekir, E-mail: bsari@gazi.edu.tr

2017-07-01

Highlights: • In this study, ternary composite/nanocomposite films were synthesized. • Magnetic field-sensitive folding films were prepared without any elastomer. • Morphological studies show that all composite films have a smooth surface. • The ternary composites/nanocomposite show improved thermal stability compared to the pure PF. - Abstract: In this study, polyfuran and poly(vinyl acetate)/poly(vinyl chloride)/polyfuran ternary composites were synthesized via the chemical polymerization method. The temperature and magnetic field–sensitive novel composites and the nanocomposite were obtained in the form of powders and films. It was observed that the prepared novel conductive films have superior properties at a certain temperature range (25–50 °C) such as bending and folding. The structural properties, thermal behavior, surface morphology, internal structure, and surface roughness of the prepared samples were investigated by various characterization techniques. The conductivities of the samples were measured at room temperature and different temperatures by the four-point technique. X-ray Diffraction analysis results demonstrated that the PF and composites have an amorphous structure, whereas the nanocomposite is in crystalline form. The saturation magnetization (Ms) values of the magnetite and nanocomposite were found to be 58.9 and 5.3 emu g{sup −1}, respectively. It was found that magnetite-doped nanocomposite has superparamagnetic properties at room temperature.

Role of electrolytes in the preparation of nanoparticles via the emulsion polymerization of vinyl pivalate.

Science.gov (United States)

Kikuchi, Kenji; Kitawaki, Mayuka; Suzuki, Atsushi; Oku, Takeo

2009-10-15

By controlling both the kind of ion and the ionic strength of electrolytes in an emulsion polymerization system of vinyl pivalate containing about 1% sodium lauryl sulfate as a surfactant, nanoparticles of polyvinylpivalate having a diameter of about 25 nm were successfully prepared. The use of high concentrations of lithium chloride and lithium sulfate (approximately 1.0 mol L(-1)) prevented the nanoparticles from aggregating and produced nanoparticles sizes of 25-50 nm. Ammonium acetate and sodium acetate, on the other hand, accelerated the aggregate of the nanoparticles. These phenomena were examined in detail and found to be similar to the Hofmeister phenomena and the combination rule proposed by Craig et al.

Sorption and permeation of solutions of chloride salts, water and methanol in a Nafion membrane

International Nuclear Information System (INIS)

Villaluenga, J.P.G.; Barragan, V.M.; Seoane, B.; Ruiz-Bauza, C.

2006-01-01

The sorption of water-methanol mixtures containing a dissolved chloride salt in a Nafion 117 membrane, and their transport through the membrane under the driving force of a pressure gradient, have been studied. Both type of experiments was performed by using five different salts: lithium chloride, sodium chloride, cesium chloride, magnesium chloride and calcium chloride. It was observed that both the permeation flow through the membrane and the membrane swelling increase significantly with the methanol content of the solutions. These facts are attributed to the increase in wet membrane porosity, which brings about the increase of the mobility of solvents in the membrane, besides the increase of the mobility of the polymer pendant chains. In contrast, the influence of the type of electrolyte on the membrane porosity and permeability is not very important, with the exception of the CsCl solutions, which is probably due to the small hydration ability of the Cs + ion

Chloroindolyl-3-acetic Acid and its Methyl Ester Incorporation of 36Cl in Immature Seeds of Pea and Barley

DEFF Research Database (Denmark)

Engvild, Kjeld Christensen

1974-01-01

Immature seeds of pea and barley were harvested on plants grown in solutions containing 36Cl−, but no other chlorides. Autoradiography of two-dimensional thin layer chromatograms (silicagel) of butanol extracts of freeze-dried seeds showed the presence in both species of several radioactive...... compounds besides Cl−. One compound, present in pea and probably in barley, cochromatographed with a mixture of 4- and 6-chloroindolyl-3-acetic acid methyl esters. Another, detected in pea, but probably not in barley, cochromatographed with a mixture of 4-and 6-chloroindolyl-3-acetic acids....

Effect of acetic acid on citric acid fermentation in an integrated citric acid-methane fermentation process.

Science.gov (United States)

Xu, Jian; Chen, Yang-Qiu; Zhang, Hong-Jian; Tang, Lei; Wang, Ke; Zhang, Jian-Hua; Chen, Xu-Sheng; Mao, Zhong-Gui

2014-09-01

An integrated citric acid-methane fermentation process was proposed to solve the problem of extraction wastewater in citric acid fermentation process. Extraction wastewater was treated by anaerobic digestion and then recycled for the next batch of citric acid fermentation to eliminate wastewater discharge and reduce water resource consumption. Acetic acid as an intermediate product of methane fermentation was present in anaerobic digestion effluent. In this study, the effect of acetic acid on citric acid fermentation was investigated and results showed that lower concentration of acetic acid could promote Aspergillus niger growth and citric acid production. 5-Cyano-2,3-ditolyl tetrazolium chloride (CTC) staining was used to quantify the activity of A. niger cells, and the results suggested that when acetic acid concentration was above 8 mM at initial pH 4.5, the morphology of A. niger became uneven and the part of the cells' activity was significantly reduced, thereby resulting in deceasing of citric acid production. Effects of acetic acid on citric acid fermentation, as influenced by initial pH and cell number in inocula, were also examined. The result indicated that inhibition by acetic acid increased as initial pH declined and was rarely influenced by cell number in inocula.

Influence of bicarbonate on the sensitivity of renin release to sodium chloride

DEFF Research Database (Denmark)

Skøtt, O; Jensen, B L

1989-01-01

glomeruli treated with bicarbonate/chloride exchange inhibitor (DNDS), NaCl/KCl cotransport inhibitor (bumetanide), or Na+/H+ antiport inhibitor (amiloride) in the presence or absence of bicarbonate. In addition, the sensitivity to increases in osmolality by addition of sucrose was tested in the presence...... or absence of bicarbonate. Renin release from time controls superfused with a bicarbonate-free Ringer was identical to release from glomeruli superfused with a bicarbonate Ringer. DNDS (0.11 or 1.1 mM) had no effect on renin release in a bicarbonate Ringer. 30 mM sucrose inhibited renin release independently...... of bicarbonate. 15 mM NaCl stimulated renin release when bicarbonate was absent, while it caused an inhibition in the presence of bicarbonate. When bicarbonate/chloride exchange was inhibited, addition of NaCl stimulated renin release even when bicarbonate was present. The effect of NaCl on renin release...

Chemical castration in cattle with intratesticular injection of sodium chloride: Effects on stress and inflammatory markers.

Science.gov (United States)

Oliveira, Fernando C; Ferreira, Carlos E R; Haas, Cristina S; Oliveira, Leonardo G; Mondadori, Rafael G; Schneider, Augusto; Rovani, Monique T; Gonçalves, Paulo B D; Vieira, Arnaldo D; Gasperin, Bernardo G; Lucia, Thomaz

2017-03-01

Intratesticular injection (ITI) of sodium chloride (NaCl) is efficient for chemical castration of young calves, but its effects on calves welfare are unknown. Two experiments were conducted to evaluate the effects of ITI of 20% NaCl on stress and inflammatory markers in calves less than 20 days old and to assess the efficiency of ITI of 30% NaCl in 5 months old calves. In Experiment 1, control calves were only restrained and compared to calves submitted to castration through surgery (SC) and ITI with 20% NaCl (n = 9/group). No differences were observed for the eye corner temperature measured by thermography from 60 s before to 60 s after the procedures (P > 0.05). In the SC group, acute serum cortisol levels increased at 30 and 60 min after the procedure, but increased levels in the ITI group occurred only at 30 min (P  0.05). Scrotal temperature was higher at D1 in the SC group than for the other groups, but lowest at D4 compared to the control (both P castration through ITI of 20% NaCl in young calves was followed by slight stress and inflammatory responses compared to surgical castration. However, ITI of 30% NaCl was ineffective for chemical castration of 5 months old calves. Copyright © 2016 Elsevier Inc. All rights reserved.

Reverse osmosis separation of radium from dilute aqueous solutions

International Nuclear Information System (INIS)

Subramanian, K.S.; Sastri, V.S.

1980-01-01

Porous cellulose acetate membranes obtained from Osmonics Inc. were characterized in terms of pure water permeability constant, solute transport parameter, and mass transfer coefficient with aqueous sodium chloride solution as the reference system. Reverse osmosis separation behavior of radium-226 as nitrate, chloride, and sulfate salts was studied. Reverse osmosis method of removing radium-226 from aqueous solutions has been compared with other methods, and it has been shown to be one of the best methods for alleviating radium contamination problems

Cloreto de sódio, benzocaína e óleo de cravo-da-índia na água de transporte de tilápia-do-nilo Sodium chloride, benzocaine and clove oil in tilapia transport water

Directory of Open Access Journals (Sweden)

José Ricardo Oliveira

2009-07-01

Full Text Available Testou-se a ação de diferentes concentrações de cloreto de sódio, benzocaína e óleo de cravo-da-índia na sobrevivência de alevinos e juvenis de tilápia (Oreochromis niloticus, linhagem chitralada, por 5 horas visando ao transporte. Utilizaram-se 1.350 alevinos (9,74 ± 0,04 g e 6,79 ± 0,01 cm e 270 juvenis (29,6 ± 0,06 g e 11,52 ± 0,01. Os peixes foram mantidos em jejum por 24 horas em quatro caixas de amianto (500 L com aeração constante. Em seguida, os peixes foram distribuídos em 54 sacos plásticos, capacidade para 5 L e mantidos em soluções de: cloreto de sódio nas concentrações de (0; 4; ou 8 g/L, benzocaína (0; 20; ou 40 mg/L e óleo de cravo (0; 2; ou 5 mg/L. O delineamento foi em blocos casualizados, com três repetições, em arranjo multifatorial, com três fatores: substâncias, peixes e concentrações de cada substância em estudo. Mensuraram-se, no início, os parâmetros oxigênio dissolvido, temperatura, pH, salinidade e amônia e, ao final do experimento, a glicose dos peixes. Maiores níveis de glicose foram registrados nos juvenis mantidos na água com óleo de cravo e cloreto de sódio. Não foi observada diferença significativa na sobrevivência entre os tipos de peixes e as substâncias. Entretanto, as dosagens de cloreto de sódio e benzocaína ocasionaram diferenças significativas na taxa de sobrevivência. A sobrevivência foi baixa nos alevinos com 0 g/L de cloreto de sódio e diferiu das dosagens 4 e 8 g/L. O óleo de cravo promoveu resultados similares, em todas as dosagens e substâncias, de taxas de glicose. Ao final do experimento, a sobrevivência foi satisfatória, com média geral de 97,26%, comprovando que as três substâncias podem ser usadas no transporte de alevinos e juvenis durante 5 horas. Sugere-se o cloreto de sódio por seu melhor custo-benefício.The action of different concentrations of sodium chloride, benzocaine and clove oil in the survival of fingerling and juvenile

Application of cone packing model in extraction: Pt.1

International Nuclear Information System (INIS)

Li Xingfu; Tang Bolin; Sun Pengnian

1987-01-01

Synergistic effect in trinary system: substrate 1 + substrate 2 + extractant, is reported with the extraction for uranyl ion in mixed acetate and chloride substrates by applying cone packing model. Based on the cone packing model, ligand packing around the uranyl equatorial plane should be neither overcrowded nor undercrowded. The sum of ligand's Fan Angle (FA) around the uranyl equatorial plane provides a useful criterion for estimating steric crowding. Whereas FAS of UO 2 (OAc) 2 (TBP) 2 , UO 2 (OAc) 2 TBP, UO 2 Cl 2 (TBP) 2 and UO 2 Cl 2 (TBP) 3 are 204, 164, 164 and 203 deg respectively, none is favourable to form stable extracted complexes. FAS of UO 2 (OAc)Cl(TBP) 2 is l84 deg indicating the most favorable packing. Therefore synergistic effect based on the formation of extracted complex UO 2 (OAc)Cl(TBP) 2 in mixed acetate and chloride solution was predicted. The above speculation was confirmed by extraction of uranyl ion in the substrates of sodium acetate-acetic acid and ammonium chloride. Keeping the total concentration of substrates constant, synergistic extraction is found at l:3 acetate to chloride ratio which shifts a little on changing concentration of the uranyl ion from 3.97 x 10 -4 mol·dm -3 to 2.06 x 10 -2 mol·dm -3 . The extracted complex was proved to be mostly UO 2 (OAc)Cl(TBP) 2 by using the slope method and analysing the uranyl and chloride concentration in organic phase. Variation of the distribution coefficient of synergistic effect with the pH of the medium was studied. The similiar effect was found with other oxtractants and diluents

Toxicity of sodium chloride and methyl parathion on the macrophyte Lemna minor (Linnaeus, 1753 with respect to frond number and chlorophyll

Directory of Open Access Journals (Sweden)

Erlei Cassiano Keppeler

2009-06-01

Full Text Available http://dx.doi.org/10.5007/2175-7925.2009v22n3p27 Duckweed, Lemna minor L., is a suitable plant model for toxicity evaluation of many contaminants due to its small size and rapid growth. Methyl parathion is a toxic compound which is utilized to eliminate aquatic insect larvae, among other purposes. Its toxicity was evaluated with the use of L. minor in this study. Methyl parathion was added to Hoagland’s nutrient medium at concentrations of 0, 8, 16, 22, 28 and 32mg.L–1. Lemna minor is used as a tool in evaluating chemical test products for toxic effects. The sensitivity of Lemna to sodium chloride, the reference substance, at concentrations of 0, 2, 4, 6, 7 and 8 g.L–1, was determined for comparison and resulted in an IC50 of 6.87g.L–1. Methyl parathion in L. minor showed an IC50 of 49.48mg.L–1.

The preparation of accelerator targets by the evaporation of acetate-organic solutions in the presence of NH3 gas

International Nuclear Information System (INIS)

Cai, S.Y.; Ghiorso, A.; Hoffman, D.C.

1987-03-01

The chemical methods described in this paper have been developed for preparation of isotopic targets for bombardment by accelerator-produced ions. Three systems are compared: nitrate-, chloride-, and acetate-organic solutions. The best method was found to be the metallic acetate-organic solution system, evaporated onto the substrate in the presence of ammonia gas. A detailed procedure is given for this method. The targets obtained by the acetate-organic solution system are uniform and adherent. The hydroxide forms fine crystals of good quality for target thicknesses from a few μg/cm 2 to several mg/cm 2 . Thicknesses up to 5 mg/cm 2 of Eu as the oxide were obtained by this method. The process is simple and fast. 18 refs., 1 tab

Acetate Kinase Isozymes Confer Robustness in Acetate Metabolism

DEFF Research Database (Denmark)

Chan, Siu Hung Joshua; Nørregaard, Lasse; Solem, Christian

2014-01-01

transcription structure, determining enzyme characteristics and effect on growth physiology. The results show that the two ACKs are most likely individually transcribed. AckA1 has a much higher turnover number and AckA2 has a much higher affinity for acetate in vitro. Consistently, growth experiments of mutant...... physiological roles in L. lactis to maintain a robust acetate metabolism for fast growth at different extracellular acetate concentrations. The existence of ACK isozymes may reflect a common evolutionary strategy in bacteria in an environment with varying concentrations of acetate.......Acetate kinase (ACK) (EC no: 2.7.2.1) interconverts acetyl-phosphate and acetate to either catabolize or synthesize acetyl-CoA dependent on the metabolic requirement. Among all ACK entries available in UniProt, we found that around 45% are multiple ACKs in some organisms including more than 300...

Multicomponent synthesis of imidazo [1,2-a] pyridines using catalytic zinc chloride

CSIR Research Space (South Africa)

Rousseau, AL

2007-06-01

Full Text Available HN R1 R2 Scheme 1. Tetrahedron Letters 48 (2007) 4079–4082 chloride,12 acetic acid,10a perchloric acid,10e or Montmo- rillonite clay K1013 to catalyze the reaction. The use of solid supports with a range of acid catalysts in the 3CC reaction... tempera- ture (for reactions catalyzed by scandium triflate, acetic acid, toluenesulfonic acid or perchloric acid) or using N X N 1 X=CH 2 X=N N N 3 R1=R2=Cl, R3=R4=C3H7 4 R1=R2=R3=R4=CH3 R1 R2 O N R3 R4 N N SO2Me antagonists.9 Drug...

Study of the transport characteristics of uranyl chloride in a highly concentrated aqueous solution of sodium chloride

International Nuclear Information System (INIS)

Murso, H.

1986-01-01

The purpose of this work was the study of the transport processes of uranyl chloride at various temperatures, in order to be able to estimate the danger potential of the intrusion of water during storage in salt form. For this the concentration dependency of the approximated principal diffusion coefficients of uranyl chloride in a table salt solution, which with a c(NaCl) = 5.2 mol/l is almost at the saturation point, was studied at 25, 40 and 50degC. The measurements were successful in the ternarian system UO 2 Cl 2 -NaCl-H 2 O with absorption optics. An unexpected temperature dependency of the diffusion coefficients was found, which reached its minimum at 40degC with UO 2 Cl 2 concentrations of less than 2x10 -2 mol/l. For comparison the diffusion coefficients were measured in the binary system UO 2 Cl 2 -H 2 O and compared with theoretical calculations. The cause for the poor correlation found here is thought to be the hydrolysis products, whose formation is strongly influenced by the foreign-electrolyte concentration (NaCl). For clarification, viscosity measurements and molar mass determinations (ultracentrifuge) will be done. Some pH-dependent hydrolysis equilibriums are being postulated and the equilibrium constants of uranyl hydroxo complexes are being determined by sedimentation analysis. (orig./RB) [de

Salt (sodium chloride) content of retail samples of Nigerian white bread: implications for the daily salt intake of normotensive and hypertensive adults.

Science.gov (United States)

Nwanguma, B C; Okorie, C H

2013-10-01

Bread has been identified as a major contributor to the excessive salt (sodium chloride) intake of consumers in many countries, some of which have very high incidences of hypertension and related cardiovascular complications, such as stroke. This has prompted a global rise in interest in the salt content of breads produced and consumed in many other countries. The sodium contents of retail samples of 100 brands of Nigerian white bread were determined by photometry with a view to estimating the relative contribution of bread to the recommended daily sodium intake of both normotensive and hypertensive adults in the country. The salt content of the bread samples varied extensively, ranging from 0.51 g per 100 g (0.51%) to 1.8 g per 100 g (1.8%). The average salt content was 1.36 g per 100 g. Based on an estimated consumption of six slices of bread (about 180 g) per meal of bread, this equates to a daily intake of between 0.99 g and 3.33 g of salt from bread alone. This represents between 19.8% and 66.6% of the recommended daily allowance of 5 g for normotensive adults, and between 24.75% and 83.25% of the recommended daily allowance of 4 g for hypertensive adults. The consumption of some brands of bread by normotensive and hypertensive adults puts them at great risk of exceeding their recommended daily allowance for salt. Thus, there is an urgent need to regulate the amount of salt added to bread. In the interim, compelling bakers to declare the salt content of their products on the packaging could help consumers, especially hypertensive adults, avoid brands with a high salt content. © 2013 The Authors Journal of Human Nutrition and Dietetics © 2013 The British Dietetic Association Ltd.

Thermal annealing of gamma irradiated ammonium chloride (Preprint no. RC-37)

International Nuclear Information System (INIS)

Kalkar, C.D.; Lala, Neeta

1991-01-01

Ammonium chloride produces N 2 H 4 + and Cl 2 as the main radiolytic products on gamma irradiation. Thermal annealing has a marked effect on the stability of N 2 H 4 + and Cl 2 . During the thermal annealing the chemical yield of nitrite and iodine was studied by dissolving irradiated ammonium chloride in aqueous sodium nitrate and potassium iodide respectively. The yield of iodine in isochronal annealing showed an exponential behaviour with temperature while that of nitrite showed a decrease and then increases at higher temperatures. The results are explained on the basis of dissociation and recombination of N 2 H 4 + with temperature. (author). 3 refs., 2 figs

Design and functionality of a segmented heat-storage prototype utilizing stable supercooling of sodium acetate trihydrate in a solar heating system

DEFF Research Database (Denmark)

Englmair, Gerald; Moser, Christoph; Furbo, Simon

2018-01-01

acetate trihydrate composites to conserve the latent heat of fusion for long-term heat storage. A control strategy directed heat from a solar collector array to either the PCM storage or a water buffer storage. Several PCM units had to be charged in parallel when the solar collector output peaked at 16 k......A solar heating system with 22.4m2 of solar collectors, a heat storage prototype consisting of four 200 kg phase-change material (PCM) storage units, and a 735 L water tank was designed to improve solar heat supply in single-family houses. The PCM storage utilized stable supercooling of sodium......W. A single unit was charged with 27.4 kWh of heat within four hours on a sunny day, and the PCM temperature increased from 20 °C to 80 °C. The sensible heat from a single PCM unit was transferred to the water tank starting with about 32 kW of thermal power after it had fully melted at 80 °C. A mechanical...

Effect of different ions on the anodic behaviour of alloy 800 chloride solutions at high temperature

International Nuclear Information System (INIS)

Lafont, C.J.; Alvarez, M.G.

1993-01-01

The anodic behaviour and passivity breakdown of alloy 800 in sodium bicarbonate and sodium phosphate aqueous solutions were studied in the temperature range from 100 degrees C to 280 degrees C by means of electrochemical techniques. The effect of phosphate or bicarbonate additions on the pitting susceptibility and pitting morphology of the alloy in chloride solutions was also examined. Experiments were performed in the following solutions: 0.1M NaHCO 3 , at 100 degrees C, 200 degrees C, 280 degrees C; 0.06M NaH 2 PO 4 + 0.04M Na 2 HPO 4 , at 100 degrees C, 200 degrees C and 280 degrees C, and 0.1M NaCl with different additions of bicarbonate ion (0.02M, 0.05M and 0.1M) and phosphate ion (0.01M, 0.05M and 0.1M) at 100 degrees C and 280 degrees C. The anodic polarization curves of alloy 800 in deaerated 0.1M NaHCO 3 and 0.06M NaH 2 PO 4 + 0.04M Na 2 HPO 4 solutions exhibited a similar shape at all the tested temperatures. No localized or generalized corrosion was detected on the metallic surface after polarization. The results obtained in chloride plus bicarbonate and chloride plus phosphate mixtures showed that the pitting potential of alloy 800 in chloride solutions was increased by the presence of bicarbonate or phosphate ions. In those solutions where the inhibitor concentration in the mixture is equal or higher than the chloride concentration , the behaviour of the alloy is similar to the one observed in the absence of chlorides. Changes in pitting morphology were found in phosphate containing solutions, while the pits found in bicarbonate containing solutions were similar to those formed in pure chloride solutions. (author). 3 refs., 4 figs